[openwrt/openwrt] uboot-mediatek: add support for Bananapi BPi-R3
LEDE Commits
lede-commits at lists.infradead.org
Tue Aug 30 12:48:24 PDT 2022
dangole pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/c2bc1bd99aabe1298c93cebc0a434c91c754f3ca
commit c2bc1bd99aabe1298c93cebc0a434c91c754f3ca
Author: Daniel Golle <daniel at makrotopia.org>
AuthorDate: Wed Jul 13 04:29:34 2022 +0100
uboot-mediatek: add support for Bananapi BPi-R3
The Bananapi BPi-R3 board can boot from eMMC, SD card, SPI-NAND and
SPI-NOR, depending on the position of switches controlling the BOOTSEL
bootstrap pins as we as hard-wired chip-select lines. The position of the
chip-select switch SW6 decides whether either SD card or eMMC can be
accessed, SW5 selects either SPI-NAND or SPI-NOR.
Generate U-Boot for all 4 boot options. The SD card version allows
installation to SPI-NAND and SPI-NOR (eMMC cannot be accessed
simultanously with the SD card), the SPI-NAND version allows installation
to eMMC.
Signed-off-by: Daniel Golle <daniel at makrotopia.org>
---
package/boot/uboot-mediatek/Makefile | 63 +-
.../uboot-mediatek/patches/430-add-bpi-r3.patch | 1368 ++++++++++++++++++++
2 files changed, 1428 insertions(+), 3 deletions(-)
diff --git a/package/boot/uboot-mediatek/Makefile b/package/boot/uboot-mediatek/Makefile
index c89fb197ae..7bfc8fd64b 100644
--- a/package/boot/uboot-mediatek/Makefile
+++ b/package/boot/uboot-mediatek/Makefile
@@ -180,7 +180,60 @@ define U-Boot/mt7986_rfb
BUILD_SUBTARGET:=filogic
BUILD_DEVICES:=mediatek_mt7986-rfb
UBOOT_CONFIG:=mt7986_rfb
- UBOOT_IMAGE:=u-boot.bin
+ UBOOT_IMAGE:=u-boot.fip
+ BL2_BOOTDEV:=sdmmc
+ BL2_SOC:=mt7986
+ BL2_DDRTYPE:=ddr4
+ DEPENDS:=+trusted-firmware-a-mt7986-sdmmc-ddr4
+endef
+
+define U-Boot/mt7986_bananapi_bpi-r3-emmc
+ NAME:=BananaPi BPi-R3
+ BUILD_SUBTARGET:=filogic
+ BUILD_DEVICES:=bananapi_bpi-r3
+ UBOOT_CONFIG:=mt7986a_bpi-r3-emmc
+ UBOOT_IMAGE:=u-boot.fip
+ BL2_BOOTDEV:=emmc
+ BL2_SOC:=mt7986
+ BL2_DDRTYPE:=ddr4
+ DEPENDS:=+trusted-firmware-a-mt7986-emmc-ddr4
+endef
+
+define U-Boot/mt7986_bananapi_bpi-r3-sdmmc
+ NAME:=BananaPi BPi-R3
+ BUILD_SUBTARGET:=filogic
+ BUILD_DEVICES:=bananapi_bpi-r3
+ UBOOT_CONFIG:=mt7986a_bpi-r3-sd
+ UBOOT_IMAGE:=u-boot.fip
+ BL2_BOOTDEV:=sdmmc
+ BL2_SOC:=mt7986
+ BL2_DDRTYPE:=ddr4
+ DEPENDS:=+trusted-firmware-a-mt7986-sdmmc-ddr4
+endef
+
+define U-Boot/mt7986_bananapi_bpi-r3-snand
+ NAME:=BananaPi BPi-R3
+ BUILD_SUBTARGET:=filogic
+ BUILD_DEVICES:=bananapi_bpi-r3
+ UBOOT_CONFIG:=mt7986a_bpi-r3-snand
+ UBOOT_IMAGE:=u-boot.fip
+ BL2_BOOTDEV:=spim-nand
+ BL2_SOC:=mt7986
+ BL2_DDRTYPE:=ddr4
+ DEPENDS:=+trusted-firmware-a-mt7986-spim-nand-ddr4
+endef
+
+define U-Boot/mt7986_bananapi_bpi-r3-nor
+ NAME:=BananaPi BPi-R3
+ BUILD_SUBTARGET:=filogic
+ BUILD_DEVICES:=bananapi_bpi-r3
+ UBOOT_CONFIG:=mt7986a_bpi-r3-nor
+ UBOOT_IMAGE:=u-boot.fip
+ BL2_BOOTDEV:=nor
+ BL2_SOC:=mt7986
+ BL2_DDRTYPE:=ddr4
+ DEPENDS:=+trusted-firmware-a-mt7986-nor-ddr4
+ FIP_COMPRESS:=1
endef
UBOOT_TARGETS := \
@@ -199,6 +252,10 @@ UBOOT_TARGETS := \
mt7628_rfb \
ravpower_rp-wd009 \
mt7629_rfb \
+ mt7986_bananapi_bpi-r3-emmc \
+ mt7986_bananapi_bpi-r3-sdmmc \
+ mt7986_bananapi_bpi-r3-snand \
+ mt7986_bananapi_bpi-r3-nor \
mt7986_rfb
ifdef CONFIG_TARGET_mediatek
@@ -207,11 +264,11 @@ endif
define Build/fip-image
$(if $(FIP_COMPRESS),\
- xz -f -e -k -9 -C crc32 $(STAGING_DIR_IMAGE)/$(BUILD_SUBTARGET)-$(BL2_BOOTDEV)-$(BL2_DDRBLOB)ddr-bl31.bin ;\
+ xz -f -e -k -9 -C crc32 $(STAGING_DIR_IMAGE)/$(if $(BL2_SOC),$(BL2_SOC),$(BUILD_SUBTARGET))-$(BL2_BOOTDEV)-$(if $(BL2_DDRTYPE),$(BL2_DDRTYPE)-)$(if $(BL2_DDRBLOB),$(BL2_DDRBLOB)ddr-)bl31.bin ;\
xz -f -e -k -9 -C crc32 $(PKG_BUILD_DIR)/u-boot.bin \
)
$(STAGING_DIR_HOST)/bin/fiptool create \
- --soc-fw $(STAGING_DIR_IMAGE)/$(BUILD_SUBTARGET)-$(BL2_BOOTDEV)-$(BL2_DDRBLOB)ddr-bl31.bin$(if $(FIP_COMPRESS),.xz) \
+ --soc-fw $(STAGING_DIR_IMAGE)/$(if $(BL2_SOC),$(BL2_SOC),$(BUILD_SUBTARGET))-$(BL2_BOOTDEV)-$(if $(BL2_DDRTYPE),$(BL2_DDRTYPE)-)$(if $(BL2_DDRBLOB),$(BL2_DDRBLOB)ddr-)bl31.bin$(if $(FIP_COMPRESS),.xz) \
--nt-fw $(PKG_BUILD_DIR)/u-boot.bin$(if $(FIP_COMPRESS),.xz) \
$(PKG_BUILD_DIR)/u-boot.fip
endef
diff --git a/package/boot/uboot-mediatek/patches/430-add-bpi-r3.patch b/package/boot/uboot-mediatek/patches/430-add-bpi-r3.patch
new file mode 100644
index 0000000000..48835e43af
--- /dev/null
+++ b/package/boot/uboot-mediatek/patches/430-add-bpi-r3.patch
@@ -0,0 +1,1368 @@
+--- a/arch/arm/dts/Makefile
++++ b/arch/arm/dts/Makefile
+@@ -1211,6 +1211,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
+ mt7981-snfi-nand-rfb.dtb \
+ mt7981-emmc-rfb.dtb \
+ mt7981-sd-rfb.dtb \
++ mt7986a-bpi-r3-sd.dtb \
++ mt7986a-bpi-r3-emmc.dtb \
+ mt7986a-rfb.dtb \
+ mt7986b-rfb.dtb \
+ mt7986a-sd-rfb.dtb \
+--- /dev/null
++++ b/configs/mt7986a_bpi-r3-emmc_defconfig
+@@ -0,0 +1,192 @@
++CONFIG_ARM=y
++CONFIG_POSITION_INDEPENDENT=y
++CONFIG_ARCH_MEDIATEK=y
++CONFIG_TARGET_MT7986=y
++CONFIG_SYS_TEXT_BASE=0x41e00000
++CONFIG_SYS_MALLOC_F_LEN=0x4000
++CONFIG_NR_DRAM_BANKS=1
++CONFIG_DEFAULT_DEVICE_TREE="mt7986a-bpi-r3-emmc"
++CONFIG_DEFAULT_ENV_FILE="bananapi_bpi-r3_emmc_env"
++CONFIG_DEFAULT_FDT_FILE="mediatek/mt7986a-bpi-r3-emmc.dtb"
++CONFIG_OF_LIBFDT_OVERLAY=y
++CONFIG_DEBUG_UART_BASE=0x11002000
++CONFIG_DEBUG_UART_CLOCK=40000000
++CONFIG_DEBUG_UART=y
++CONFIG_SYS_LOAD_ADDR=0x46000000
++CONFIG_NET_RANDOM_ETHADDR=y
++CONFIG_SMBIOS_PRODUCT_NAME=""
++CONFIG_AUTOBOOT_KEYED=y
++CONFIG_BOOTDELAY=30
++CONFIG_AUTOBOOT_MENU_SHOW=y
++CONFIG_CFB_CONSOLE_ANSI=y
++CONFIG_BOARD_LATE_INIT=y
++CONFIG_BUTTON=y
++CONFIG_BUTTON_GPIO=y
++CONFIG_GPIO_HOG=y
++CONFIG_CMD_ENV_FLAGS=y
++CONFIG_FIT=y
++CONFIG_FIT_ENABLE_SHA256_SUPPORT=y
++CONFIG_LED=y
++CONFIG_LED_BLINK=y
++CONFIG_LED_GPIO=y
++CONFIG_LOGLEVEL=7
++CONFIG_LOG=y
++CONFIG_SYS_PROMPT="MT7986> "
++CONFIG_CMD_BOOTMENU=y
++CONFIG_CMD_BOOTP=y
++CONFIG_CMD_BUTTON=y
++CONFIG_CMD_CACHE=y
++CONFIG_CMD_CDP=y
++CONFIG_CMD_DHCP=y
++CONFIG_CMD_DM=y
++CONFIG_CMD_DNS=y
++CONFIG_CMD_ECHO=y
++CONFIG_CMD_ENV_READMEM=y
++CONFIG_CMD_ERASEENV=y
++CONFIG_CMD_EXT4=y
++CONFIG_CMD_FAT=y
++CONFIG_CMD_FDT=y
++CONFIG_CMD_FS_GENERIC=y
++CONFIG_CMD_FS_UUID=y
++CONFIG_CMD_GPIO=y
++CONFIG_CMD_GPT=y
++CONFIG_CMD_HASH=y
++CONFIG_CMD_ITEST=y
++CONFIG_CMD_LED=y
++CONFIG_CMD_LICENSE=y
++CONFIG_CMD_LINK_LOCAL=y
++# CONFIG_CMD_MBR is not set
++CONFIG_CMD_MMC=y
++CONFIG_CMD_MTD=y
++CONFIG_CMD_PCI=y
++CONFIG_CMD_PSTORE=y
++CONFIG_CMD_PSTORE_MEM_ADDR=0x42ff0000
++CONFIG_CMD_SF_TEST=y
++CONFIG_CMD_PING=y
++CONFIG_CMD_PXE=y
++CONFIG_CMD_PWM=y
++CONFIG_CMD_SMC=y
++CONFIG_CMD_TFTPBOOT=y
++CONFIG_CMD_TFTPSRV=y
++CONFIG_CMD_UBI=y
++CONFIG_CMD_UBI_RENAME=y
++CONFIG_CMD_UBIFS=y
++CONFIG_CMD_ASKENV=y
++CONFIG_CMD_PART=y
++CONFIG_CMD_RARP=y
++CONFIG_CMD_SETEXPR=y
++CONFIG_CMD_SLEEP=y
++CONFIG_CMD_SNTP=y
++CONFIG_CMD_SOURCE=y
++CONFIG_CMD_STRINGS=y
++CONFIG_CMD_USB=y
++CONFIG_CMD_UUID=y
++CONFIG_DISPLAY_CPUINFO=y
++CONFIG_DM_MMC=y
++CONFIG_DM_MTD=y
++CONFIG_DM_REGULATOR=y
++CONFIG_DM_REGULATOR_FIXED=y
++CONFIG_DM_REGULATOR_GPIO=y
++CONFIG_DM_USB=y
++CONFIG_DM_PWM=y
++CONFIG_PWM_MTK=y
++CONFIG_HUSH_PARSER=y
++CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
++CONFIG_SYS_RELOC_GD_ENV_ADDR=y
++CONFIG_VERSION_VARIABLE=y
++CONFIG_PARTITION_UUIDS=y
++CONFIG_NETCONSOLE=y
++CONFIG_REGMAP=y
++CONFIG_SYSCON=y
++CONFIG_CLK=y
++CONFIG_DM_GPIO=y
++CONFIG_DM_SCSI=y
++CONFIG_AHCI=y
++CONFIG_AHCI_PCI=y
++CONFIG_SCSI_AHCI=y
++CONFIG_SCSI=y
++CONFIG_CMD_SCSI=y
++CONFIG_PHY=y
++CONFIG_PHY_MTK_TPHY=y
++CONFIG_PHY_FIXED=y
++CONFIG_MTK_AHCI=y
++CONFIG_DM_ETH=y
++CONFIG_MEDIATEK_ETH=y
++CONFIG_PCI=y
++CONFIG_MTD=y
++CONFIG_MTD_UBI_FASTMAP=y
++CONFIG_DM_PCI=y
++CONFIG_PCIE_MEDIATEK=y
++CONFIG_PINCTRL=y
++CONFIG_PINCONF=y
++CONFIG_PINCTRL_MT7622=y
++CONFIG_POWER_DOMAIN=y
++CONFIG_PRE_CONSOLE_BUFFER=y
++CONFIG_PRE_CON_BUF_ADDR=0x4007EF00
++CONFIG_MTK_POWER_DOMAIN=y
++CONFIG_RAM=y
++CONFIG_DM_SERIAL=y
++CONFIG_MTK_SERIAL=y
++CONFIG_MMC=y
++CONFIG_MMC_DEFAULT_DEV=1
++CONFIG_MMC_HS200_SUPPORT=y
++CONFIG_MMC_MTK=y
++CONFIG_MMC_SUPPORTS_TUNING=y
++CONFIG_SUPPORT_EMMC_BOOT=y
++CONFIG_SPI=y
++CONFIG_DM_SPI=y
++CONFIG_MTK_SPI_NAND=y
++CONFIG_MTK_SPI_NAND_MTD=y
++CONFIG_SYSRESET_WATCHDOG=y
++CONFIG_WDT_MTK=y
++CONFIG_LZO=y
++CONFIG_ZSTD=y
++CONFIG_HEXDUMP=y
++CONFIG_RANDOM_UUID=y
++CONFIG_REGEX=y
++CONFIG_USB=y
++CONFIG_USB_HOST=y
++CONFIG_USB_XHCI_HCD=y
++CONFIG_USB_XHCI_MTK=y
++CONFIG_USB_STORAGE=y
++CONFIG_OF_EMBED=y
++CONFIG_ENV_OVERWRITE=y
++CONFIG_ENV_IS_IN_MMC=y
++CONFIG_ENV_OFFSET=0x400000
++CONFIG_ENV_OFFSET_REDUND=0x440000
++CONFIG_ENV_SIZE=0x40000
++CONFIG_ENV_SIZE_REDUND=0x40000
++CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
++CONFIG_NET_RANDOM_ETHADDR=y
++CONFIG_REGMAP=y
++CONFIG_SYSCON=y
++CONFIG_CLK=y
++CONFIG_SUPPORT_EMMC_BOOT=y
++CONFIG_MMC_HS200_SUPPORT=y
++CONFIG_MMC_MTK=y
++CONFIG_PHY_FIXED=y
++CONFIG_DM_ETH=y
++CONFIG_MEDIATEK_ETH=y
++CONFIG_PINCTRL=y
++CONFIG_PINCONF=y
++CONFIG_PINCTRL_MT7986=y
++CONFIG_POWER_DOMAIN=y
++CONFIG_MTK_POWER_DOMAIN=y
++CONFIG_DM_REGULATOR=y
++CONFIG_DM_REGULATOR_FIXED=y
++CONFIG_DM_SERIAL=y
++CONFIG_MTK_SERIAL=y
++CONFIG_HEXDUMP=y
++CONFIG_USE_DEFAULT_ENV_FILE=y
++CONFIG_MTD_SPI_NAND=y
++CONFIG_MTK_SPIM=y
++#CONFIG_MTK_SNOR=y
++CONFIG_DM_SPI_FLASH=y
++CONFIG_SPI_FLASH_MTD=y
++CONFIG_SPI_FLASH_WINBOND=y
++# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
++CONFIG_CMD_MTD=y
++CONFIG_CMD_SF=y
++CONFIG_CMD_NAND=y
++CONFIG_CMD_NAND_TRIMFFS=y
++# CONFIG_ENABLE_NAND_NMBM is not set
+--- /dev/null
++++ b/configs/mt7986a_bpi-r3-nor_defconfig
+@@ -0,0 +1,193 @@
++CONFIG_ARM=y
++CONFIG_POSITION_INDEPENDENT=y
++CONFIG_ARCH_MEDIATEK=y
++CONFIG_TARGET_MT7986=y
++CONFIG_SYS_TEXT_BASE=0x41e00000
++CONFIG_SYS_MALLOC_F_LEN=0x4000
++CONFIG_NR_DRAM_BANKS=1
++CONFIG_DEFAULT_DEVICE_TREE="mt7986a-bpi-r3-emmc"
++CONFIG_DEFAULT_ENV_FILE="bananapi_bpi-r3_nor_env"
++CONFIG_DEFAULT_FDT_FILE="mediatek/mt7986a-bpi-r3-emmc.dtb"
++CONFIG_OF_LIBFDT_OVERLAY=y
++CONFIG_DEBUG_UART_BASE=0x11002000
++CONFIG_DEBUG_UART_CLOCK=40000000
++CONFIG_DEBUG_UART=y
++CONFIG_SYS_LOAD_ADDR=0x46000000
++CONFIG_NET_RANDOM_ETHADDR=y
++CONFIG_SMBIOS_PRODUCT_NAME=""
++CONFIG_AUTOBOOT_KEYED=y
++CONFIG_BOOTDELAY=30
++CONFIG_AUTOBOOT_MENU_SHOW=y
++CONFIG_CFB_CONSOLE_ANSI=y
++CONFIG_BOARD_LATE_INIT=y
++CONFIG_BUTTON=y
++CONFIG_BUTTON_GPIO=y
++CONFIG_GPIO_HOG=y
++CONFIG_CMD_ENV_FLAGS=y
++CONFIG_FIT=y
++CONFIG_FIT_ENABLE_SHA256_SUPPORT=y
++CONFIG_LED=y
++CONFIG_LED_BLINK=y
++CONFIG_LED_GPIO=y
++CONFIG_LOGLEVEL=7
++CONFIG_LOG=y
++CONFIG_SYS_PROMPT="MT7986> "
++CONFIG_CMD_BOOTMENU=y
++CONFIG_CMD_BOOTP=y
++CONFIG_CMD_BUTTON=y
++CONFIG_CMD_CACHE=y
++CONFIG_CMD_CDP=y
++CONFIG_CMD_DHCP=y
++CONFIG_CMD_DM=y
++CONFIG_CMD_DNS=y
++CONFIG_CMD_ECHO=y
++CONFIG_CMD_ENV_READMEM=y
++CONFIG_CMD_ERASEENV=y
++CONFIG_CMD_EXT4=y
++CONFIG_CMD_FAT=y
++CONFIG_CMD_FDT=y
++CONFIG_CMD_FS_GENERIC=y
++CONFIG_CMD_FS_UUID=y
++CONFIG_CMD_GPIO=y
++CONFIG_CMD_GPT=y
++CONFIG_CMD_HASH=y
++CONFIG_CMD_ITEST=y
++CONFIG_CMD_LED=y
++CONFIG_CMD_LICENSE=y
++CONFIG_CMD_LINK_LOCAL=y
++# CONFIG_CMD_MBR is not set
++CONFIG_CMD_MMC=y
++CONFIG_CMD_MTD=y
++CONFIG_CMD_PCI=y
++CONFIG_CMD_PSTORE=y
++CONFIG_CMD_PSTORE_MEM_ADDR=0x42ff0000
++CONFIG_CMD_SF_TEST=y
++CONFIG_CMD_PING=y
++CONFIG_CMD_PXE=y
++CONFIG_CMD_PWM=y
++CONFIG_CMD_SMC=y
++CONFIG_CMD_TFTPBOOT=y
++CONFIG_CMD_TFTPSRV=y
++CONFIG_CMD_UBI=y
++CONFIG_CMD_UBI_RENAME=y
++CONFIG_CMD_UBIFS=y
++CONFIG_CMD_ASKENV=y
++CONFIG_CMD_PART=y
++CONFIG_CMD_RARP=y
++CONFIG_CMD_SETEXPR=y
++CONFIG_CMD_SLEEP=y
++CONFIG_CMD_SNTP=y
++CONFIG_CMD_SOURCE=y
++CONFIG_CMD_STRINGS=y
++CONFIG_CMD_USB=y
++CONFIG_CMD_UUID=y
++CONFIG_DISPLAY_CPUINFO=y
++CONFIG_DM_MMC=y
++CONFIG_DM_MTD=y
++CONFIG_DM_REGULATOR=y
++CONFIG_DM_REGULATOR_FIXED=y
++CONFIG_DM_REGULATOR_GPIO=y
++CONFIG_DM_USB=y
++CONFIG_DM_PWM=y
++CONFIG_PWM_MTK=y
++CONFIG_HUSH_PARSER=y
++CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
++CONFIG_SYS_RELOC_GD_ENV_ADDR=y
++CONFIG_VERSION_VARIABLE=y
++CONFIG_PARTITION_UUIDS=y
++CONFIG_NETCONSOLE=y
++CONFIG_REGMAP=y
++CONFIG_SYSCON=y
++CONFIG_CLK=y
++CONFIG_DM_GPIO=y
++CONFIG_DM_SCSI=y
++CONFIG_AHCI=y
++CONFIG_AHCI_PCI=y
++CONFIG_SCSI_AHCI=y
++CONFIG_SCSI=y
++CONFIG_CMD_SCSI=y
++CONFIG_PHY=y
++CONFIG_PHY_MTK_TPHY=y
++CONFIG_PHY_FIXED=y
++CONFIG_MTK_AHCI=y
++CONFIG_DM_ETH=y
++CONFIG_MEDIATEK_ETH=y
++CONFIG_PCI=y
++CONFIG_MTD=y
++CONFIG_MTD_UBI_FASTMAP=y
++CONFIG_DM_PCI=y
++CONFIG_PCIE_MEDIATEK=y
++CONFIG_PINCTRL=y
++CONFIG_PINCONF=y
++CONFIG_PINCTRL_MT7622=y
++CONFIG_POWER_DOMAIN=y
++CONFIG_PRE_CONSOLE_BUFFER=y
++CONFIG_PRE_CON_BUF_ADDR=0x4007EF00
++CONFIG_MTK_POWER_DOMAIN=y
++CONFIG_RAM=y
++CONFIG_DM_SERIAL=y
++CONFIG_MTK_SERIAL=y
++CONFIG_MMC=y
++CONFIG_MMC_DEFAULT_DEV=1
++CONFIG_MMC_HS200_SUPPORT=y
++CONFIG_MMC_MTK=y
++CONFIG_MMC_SUPPORTS_TUNING=y
++CONFIG_SUPPORT_EMMC_BOOT=y
++CONFIG_SPI=y
++CONFIG_DM_SPI=y
++CONFIG_MTK_SPI_NAND=y
++CONFIG_MTK_SPI_NAND_MTD=y
++CONFIG_SYSRESET_WATCHDOG=y
++CONFIG_WDT_MTK=y
++CONFIG_LZO=y
++CONFIG_ZSTD=y
++CONFIG_HEXDUMP=y
++CONFIG_RANDOM_UUID=y
++CONFIG_REGEX=y
++CONFIG_USB=y
++CONFIG_USB_HOST=y
++CONFIG_USB_XHCI_HCD=y
++CONFIG_USB_XHCI_MTK=y
++CONFIG_USB_STORAGE=y
++CONFIG_OF_EMBED=y
++CONFIG_ENV_OVERWRITE=y
++CONFIG_ENV_IS_IN_MTD=y
++CONFIG_ENV_MTD_NAME="u-boot-env"
++CONFIG_ENV_OFFSET=0x0
++CONFIG_ENV_OFFSET_REDUND=0x20000
++CONFIG_ENV_SIZE=0x20000
++CONFIG_ENV_SIZE_REDUND=0x20000
++CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
++CONFIG_NET_RANDOM_ETHADDR=y
++CONFIG_REGMAP=y
++CONFIG_SYSCON=y
++CONFIG_CLK=y
++CONFIG_SUPPORT_EMMC_BOOT=y
++CONFIG_MMC_HS200_SUPPORT=y
++CONFIG_MMC_MTK=y
++CONFIG_PHY_FIXED=y
++CONFIG_DM_ETH=y
++CONFIG_MEDIATEK_ETH=y
++CONFIG_PINCTRL=y
++CONFIG_PINCONF=y
++CONFIG_PINCTRL_MT7986=y
++CONFIG_POWER_DOMAIN=y
++CONFIG_MTK_POWER_DOMAIN=y
++CONFIG_DM_REGULATOR=y
++CONFIG_DM_REGULATOR_FIXED=y
++CONFIG_DM_SERIAL=y
++CONFIG_MTK_SERIAL=y
++CONFIG_HEXDUMP=y
++CONFIG_USE_DEFAULT_ENV_FILE=y
++#CONFIG_MTD_SPI_NAND=y
++CONFIG_MTK_SPIM=y
++#CONFIG_MTK_SNOR=y
++CONFIG_DM_SPI_FLASH=y
++CONFIG_SPI_FLASH_MTD=y
++CONFIG_SPI_FLASH_WINBOND=y
++# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
++CONFIG_CMD_MTD=y
++CONFIG_CMD_SF=y
++#CONFIG_CMD_NAND=y
++#CONFIG_CMD_NAND_TRIMFFS=y
++# CONFIG_ENABLE_NAND_NMBM is not set
+--- /dev/null
++++ b/configs/mt7986a_bpi-r3-sd_defconfig
+@@ -0,0 +1,192 @@
++CONFIG_ARM=y
++CONFIG_POSITION_INDEPENDENT=y
++CONFIG_ARCH_MEDIATEK=y
++CONFIG_TARGET_MT7986=y
++CONFIG_SYS_TEXT_BASE=0x41e00000
++CONFIG_SYS_MALLOC_F_LEN=0x4000
++CONFIG_NR_DRAM_BANKS=1
++CONFIG_DEFAULT_DEVICE_TREE="mt7986a-bpi-r3-sd"
++CONFIG_DEFAULT_ENV_FILE="bananapi_bpi-r3_sdmmc_env"
++CONFIG_DEFAULT_FDT_FILE="mediatek/mt7986a-bpi-r3-sd.dtb"
++CONFIG_OF_LIBFDT_OVERLAY=y
++CONFIG_DEBUG_UART_BASE=0x11002000
++CONFIG_DEBUG_UART_CLOCK=40000000
++CONFIG_DEBUG_UART=y
++CONFIG_SYS_LOAD_ADDR=0x46000000
++CONFIG_NET_RANDOM_ETHADDR=y
++CONFIG_SMBIOS_PRODUCT_NAME=""
++CONFIG_AUTOBOOT_KEYED=y
++CONFIG_BOOTDELAY=30
++CONFIG_AUTOBOOT_MENU_SHOW=y
++CONFIG_CFB_CONSOLE_ANSI=y
++CONFIG_BOARD_LATE_INIT=y
++CONFIG_BUTTON=y
++CONFIG_BUTTON_GPIO=y
++CONFIG_GPIO_HOG=y
++CONFIG_CMD_ENV_FLAGS=y
++CONFIG_FIT=y
++CONFIG_FIT_ENABLE_SHA256_SUPPORT=y
++CONFIG_LED=y
++CONFIG_LED_BLINK=y
++CONFIG_LED_GPIO=y
++CONFIG_LOGLEVEL=7
++CONFIG_LOG=y
++CONFIG_SYS_PROMPT="MT7986> "
++CONFIG_CMD_BOOTMENU=y
++CONFIG_CMD_BOOTP=y
++CONFIG_CMD_BUTTON=y
++CONFIG_CMD_CACHE=y
++CONFIG_CMD_CDP=y
++CONFIG_CMD_DHCP=y
++CONFIG_CMD_DM=y
++CONFIG_CMD_DNS=y
++CONFIG_CMD_ECHO=y
++CONFIG_CMD_ENV_READMEM=y
++CONFIG_CMD_ERASEENV=y
++CONFIG_CMD_EXT4=y
++CONFIG_CMD_FAT=y
++CONFIG_CMD_FDT=y
++CONFIG_CMD_FS_GENERIC=y
++CONFIG_CMD_FS_UUID=y
++CONFIG_CMD_GPIO=y
++CONFIG_CMD_GPT=y
++CONFIG_CMD_HASH=y
++CONFIG_CMD_ITEST=y
++CONFIG_CMD_LED=y
++CONFIG_CMD_LICENSE=y
++CONFIG_CMD_LINK_LOCAL=y
++# CONFIG_CMD_MBR is not set
++CONFIG_CMD_MMC=y
++CONFIG_CMD_MTD=y
++CONFIG_CMD_PCI=y
++CONFIG_CMD_PSTORE=y
++CONFIG_CMD_PSTORE_MEM_ADDR=0x42ff0000
++CONFIG_CMD_SF_TEST=y
++CONFIG_CMD_PING=y
++CONFIG_CMD_PXE=y
++CONFIG_CMD_PWM=y
++CONFIG_CMD_SMC=y
++CONFIG_CMD_TFTPBOOT=y
++CONFIG_CMD_TFTPSRV=y
++CONFIG_CMD_UBI=y
++CONFIG_CMD_UBI_RENAME=y
++CONFIG_CMD_UBIFS=y
++CONFIG_CMD_ASKENV=y
++CONFIG_CMD_PART=y
++CONFIG_CMD_RARP=y
++CONFIG_CMD_SETEXPR=y
++CONFIG_CMD_SLEEP=y
++CONFIG_CMD_SNTP=y
++CONFIG_CMD_SOURCE=y
++CONFIG_CMD_STRINGS=y
++CONFIG_CMD_USB=y
++CONFIG_CMD_UUID=y
++CONFIG_DISPLAY_CPUINFO=y
++CONFIG_DM_MMC=y
++CONFIG_DM_MTD=y
++CONFIG_DM_REGULATOR=y
++CONFIG_DM_REGULATOR_FIXED=y
++CONFIG_DM_REGULATOR_GPIO=y
++CONFIG_DM_USB=y
++CONFIG_DM_PWM=y
++CONFIG_PWM_MTK=y
++CONFIG_HUSH_PARSER=y
++CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
++CONFIG_SYS_RELOC_GD_ENV_ADDR=y
++CONFIG_VERSION_VARIABLE=y
++CONFIG_PARTITION_UUIDS=y
++CONFIG_NETCONSOLE=y
++CONFIG_REGMAP=y
++CONFIG_SYSCON=y
++CONFIG_CLK=y
++CONFIG_DM_GPIO=y
++CONFIG_DM_SCSI=y
++CONFIG_AHCI=y
++CONFIG_AHCI_PCI=y
++CONFIG_SCSI_AHCI=y
++CONFIG_SCSI=y
++CONFIG_CMD_SCSI=y
++CONFIG_PHY=y
++CONFIG_PHY_MTK_TPHY=y
++CONFIG_PHY_FIXED=y
++CONFIG_MTK_AHCI=y
++CONFIG_DM_ETH=y
++CONFIG_MEDIATEK_ETH=y
++CONFIG_PCI=y
++CONFIG_MTD=y
++CONFIG_MTD_UBI_FASTMAP=y
++CONFIG_DM_PCI=y
++CONFIG_PCIE_MEDIATEK=y
++CONFIG_PINCTRL=y
++CONFIG_PINCONF=y
++CONFIG_PINCTRL_MT7622=y
++CONFIG_POWER_DOMAIN=y
++CONFIG_PRE_CONSOLE_BUFFER=y
++CONFIG_PRE_CON_BUF_ADDR=0x4007EF00
++CONFIG_MTK_POWER_DOMAIN=y
++CONFIG_RAM=y
++CONFIG_DM_SERIAL=y
++CONFIG_MTK_SERIAL=y
++CONFIG_MMC=y
++CONFIG_MMC_DEFAULT_DEV=1
++CONFIG_MMC_HS200_SUPPORT=y
++CONFIG_MMC_MTK=y
++CONFIG_MMC_SUPPORTS_TUNING=y
++CONFIG_SUPPORT_EMMC_BOOT=y
++CONFIG_SPI=y
++CONFIG_DM_SPI=y
++CONFIG_MTK_SPI_NAND=y
++CONFIG_MTK_SPI_NAND_MTD=y
++CONFIG_SYSRESET_WATCHDOG=y
++CONFIG_WDT_MTK=y
++CONFIG_LZO=y
++CONFIG_ZSTD=y
++CONFIG_HEXDUMP=y
++CONFIG_RANDOM_UUID=y
++CONFIG_REGEX=y
++CONFIG_USB=y
++CONFIG_USB_HOST=y
++CONFIG_USB_XHCI_HCD=y
++CONFIG_USB_XHCI_MTK=y
++CONFIG_USB_STORAGE=y
++CONFIG_OF_EMBED=y
++CONFIG_ENV_OVERWRITE=y
++CONFIG_ENV_IS_IN_MMC=y
++CONFIG_ENV_OFFSET=0x400000
++CONFIG_ENV_OFFSET_REDUND=0x440000
++CONFIG_ENV_SIZE=0x40000
++CONFIG_ENV_SIZE_REDUND=0x40000
++CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
++CONFIG_NET_RANDOM_ETHADDR=y
++CONFIG_REGMAP=y
++CONFIG_SYSCON=y
++CONFIG_CLK=y
++CONFIG_SUPPORT_EMMC_BOOT=y
++CONFIG_MMC_HS200_SUPPORT=y
++CONFIG_MMC_MTK=y
++CONFIG_PHY_FIXED=y
++CONFIG_DM_ETH=y
++CONFIG_MEDIATEK_ETH=y
++CONFIG_PINCTRL=y
++CONFIG_PINCONF=y
++CONFIG_PINCTRL_MT7986=y
++CONFIG_POWER_DOMAIN=y
++CONFIG_MTK_POWER_DOMAIN=y
++CONFIG_DM_REGULATOR=y
++CONFIG_DM_REGULATOR_FIXED=y
++CONFIG_DM_SERIAL=y
++CONFIG_MTK_SERIAL=y
++CONFIG_HEXDUMP=y
++CONFIG_USE_DEFAULT_ENV_FILE=y
++CONFIG_MTD_SPI_NAND=y
++CONFIG_MTK_SPIM=y
++#CONFIG_MTK_SNOR=y
++CONFIG_DM_SPI_FLASH=y
++CONFIG_SPI_FLASH_MTD=y
++CONFIG_SPI_FLASH_WINBOND=y
++# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
++CONFIG_CMD_MTD=y
++CONFIG_CMD_SF=y
++CONFIG_CMD_NAND=y
++CONFIG_CMD_NAND_TRIMFFS=y
++# CONFIG_ENABLE_NAND_NMBM is not set
+--- /dev/null
++++ b/configs/mt7986a_bpi-r3-snand_defconfig
+@@ -0,0 +1,193 @@
++CONFIG_ARM=y
++CONFIG_POSITION_INDEPENDENT=y
++CONFIG_ARCH_MEDIATEK=y
++CONFIG_TARGET_MT7986=y
++CONFIG_SYS_TEXT_BASE=0x41e00000
++CONFIG_SYS_MALLOC_F_LEN=0x4000
++CONFIG_NR_DRAM_BANKS=1
++CONFIG_DEFAULT_DEVICE_TREE="mt7986a-bpi-r3-emmc"
++CONFIG_DEFAULT_ENV_FILE="bananapi_bpi-r3_snand_env"
++CONFIG_DEFAULT_FDT_FILE="mediatek/mt7986a-bpi-r3-emmc.dtb"
++CONFIG_OF_LIBFDT_OVERLAY=y
++CONFIG_DEBUG_UART_BASE=0x11002000
++CONFIG_DEBUG_UART_CLOCK=40000000
++CONFIG_DEBUG_UART=y
++CONFIG_SYS_LOAD_ADDR=0x46000000
++CONFIG_NET_RANDOM_ETHADDR=y
++CONFIG_SMBIOS_PRODUCT_NAME=""
++CONFIG_AUTOBOOT_KEYED=y
++CONFIG_BOOTDELAY=30
++CONFIG_AUTOBOOT_MENU_SHOW=y
++CONFIG_CFB_CONSOLE_ANSI=y
++CONFIG_BOARD_LATE_INIT=y
++CONFIG_BUTTON=y
++CONFIG_BUTTON_GPIO=y
++CONFIG_GPIO_HOG=y
++CONFIG_CMD_ENV_FLAGS=y
++CONFIG_FIT=y
++CONFIG_FIT_ENABLE_SHA256_SUPPORT=y
++CONFIG_LED=y
++CONFIG_LED_BLINK=y
++CONFIG_LED_GPIO=y
++CONFIG_LOGLEVEL=7
++CONFIG_LOG=y
++CONFIG_SYS_PROMPT="MT7986> "
++CONFIG_CMD_BOOTMENU=y
++CONFIG_CMD_BOOTP=y
++CONFIG_CMD_BUTTON=y
++CONFIG_CMD_CACHE=y
++CONFIG_CMD_CDP=y
++CONFIG_CMD_DHCP=y
++CONFIG_CMD_DM=y
++CONFIG_CMD_DNS=y
++CONFIG_CMD_ECHO=y
++CONFIG_CMD_ENV_READMEM=y
++CONFIG_CMD_ERASEENV=y
++CONFIG_CMD_EXT4=y
++CONFIG_CMD_FAT=y
++CONFIG_CMD_FDT=y
++CONFIG_CMD_FS_GENERIC=y
++CONFIG_CMD_FS_UUID=y
++CONFIG_CMD_GPIO=y
++CONFIG_CMD_GPT=y
++CONFIG_CMD_HASH=y
++CONFIG_CMD_ITEST=y
++CONFIG_CMD_LED=y
++CONFIG_CMD_LICENSE=y
++CONFIG_CMD_LINK_LOCAL=y
++# CONFIG_CMD_MBR is not set
++CONFIG_CMD_MMC=y
++CONFIG_CMD_MTD=y
++CONFIG_CMD_PCI=y
++CONFIG_CMD_PSTORE=y
++CONFIG_CMD_PSTORE_MEM_ADDR=0x42ff0000
++CONFIG_CMD_SF_TEST=y
++CONFIG_CMD_PING=y
++CONFIG_CMD_PXE=y
++CONFIG_CMD_PWM=y
++CONFIG_CMD_SMC=y
++CONFIG_CMD_TFTPBOOT=y
++CONFIG_CMD_TFTPSRV=y
++CONFIG_CMD_UBI=y
++CONFIG_CMD_UBI_RENAME=y
++CONFIG_CMD_UBIFS=y
++CONFIG_CMD_ASKENV=y
++CONFIG_CMD_PART=y
++CONFIG_CMD_RARP=y
++CONFIG_CMD_SETEXPR=y
++CONFIG_CMD_SLEEP=y
++CONFIG_CMD_SNTP=y
++CONFIG_CMD_SOURCE=y
++CONFIG_CMD_STRINGS=y
++CONFIG_CMD_USB=y
++CONFIG_CMD_UUID=y
++CONFIG_DISPLAY_CPUINFO=y
++CONFIG_DM_MMC=y
++CONFIG_DM_MTD=y
++CONFIG_DM_REGULATOR=y
++CONFIG_DM_REGULATOR_FIXED=y
++CONFIG_DM_REGULATOR_GPIO=y
++CONFIG_DM_USB=y
++CONFIG_DM_PWM=y
++CONFIG_PWM_MTK=y
++CONFIG_HUSH_PARSER=y
++CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
++CONFIG_SYS_RELOC_GD_ENV_ADDR=y
++CONFIG_VERSION_VARIABLE=y
++CONFIG_PARTITION_UUIDS=y
++CONFIG_NETCONSOLE=y
++CONFIG_REGMAP=y
++CONFIG_SYSCON=y
++CONFIG_CLK=y
++CONFIG_DM_GPIO=y
++CONFIG_DM_SCSI=y
++CONFIG_AHCI=y
++CONFIG_AHCI_PCI=y
++CONFIG_SCSI_AHCI=y
++CONFIG_SCSI=y
++CONFIG_CMD_SCSI=y
++CONFIG_PHY=y
++CONFIG_PHY_MTK_TPHY=y
++CONFIG_PHY_FIXED=y
++CONFIG_MTK_AHCI=y
++CONFIG_DM_ETH=y
++CONFIG_MEDIATEK_ETH=y
++CONFIG_PCI=y
++CONFIG_MTD=y
++CONFIG_MTD_UBI_FASTMAP=y
++CONFIG_DM_PCI=y
++CONFIG_PCIE_MEDIATEK=y
++CONFIG_PINCTRL=y
++CONFIG_PINCONF=y
++CONFIG_PINCTRL_MT7622=y
++CONFIG_POWER_DOMAIN=y
++CONFIG_PRE_CONSOLE_BUFFER=y
++CONFIG_PRE_CON_BUF_ADDR=0x4007EF00
++CONFIG_MTK_POWER_DOMAIN=y
++CONFIG_RAM=y
++CONFIG_DM_SERIAL=y
++CONFIG_MTK_SERIAL=y
++CONFIG_MMC=y
++CONFIG_MMC_DEFAULT_DEV=1
++CONFIG_MMC_HS200_SUPPORT=y
++CONFIG_MMC_MTK=y
++CONFIG_MMC_SUPPORTS_TUNING=y
++CONFIG_SUPPORT_EMMC_BOOT=y
++CONFIG_SPI=y
++CONFIG_DM_SPI=y
++CONFIG_MTK_SPI_NAND=y
++CONFIG_MTK_SPI_NAND_MTD=y
++CONFIG_SYSRESET_WATCHDOG=y
++CONFIG_WDT_MTK=y
++CONFIG_LZO=y
++CONFIG_ZSTD=y
++CONFIG_HEXDUMP=y
++CONFIG_RANDOM_UUID=y
++CONFIG_REGEX=y
++CONFIG_USB=y
++CONFIG_USB_HOST=y
++CONFIG_USB_XHCI_HCD=y
++CONFIG_USB_XHCI_MTK=y
++CONFIG_USB_STORAGE=y
++CONFIG_OF_EMBED=y
++CONFIG_ENV_OVERWRITE=y
++CONFIG_ENV_IS_IN_UBI=y
++CONFIG_ENV_UBI_PART="ubi"
++CONFIG_ENV_SIZE=0x1f000
++CONFIG_ENV_SIZE_REDUND=0x1f000
++CONFIG_ENV_UBI_VOLUME="ubootenv"
++CONFIG_ENV_UBI_VOLUME_REDUND="ubootenv2"
++CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
++CONFIG_NET_RANDOM_ETHADDR=y
++CONFIG_REGMAP=y
++CONFIG_SYSCON=y
++CONFIG_CLK=y
++CONFIG_SUPPORT_EMMC_BOOT=y
++CONFIG_MMC_HS200_SUPPORT=y
++CONFIG_MMC_MTK=y
++CONFIG_PHY_FIXED=y
++CONFIG_DM_ETH=y
++CONFIG_MEDIATEK_ETH=y
++CONFIG_PINCTRL=y
++CONFIG_PINCONF=y
++CONFIG_PINCTRL_MT7986=y
++CONFIG_POWER_DOMAIN=y
++CONFIG_MTK_POWER_DOMAIN=y
++CONFIG_DM_REGULATOR=y
++CONFIG_DM_REGULATOR_FIXED=y
++CONFIG_DM_SERIAL=y
++CONFIG_MTK_SERIAL=y
++CONFIG_HEXDUMP=y
++CONFIG_USE_DEFAULT_ENV_FILE=y
++CONFIG_MTD_SPI_NAND=y
++CONFIG_MTK_SPIM=y
++#CONFIG_MTK_SNOR=y
++#CONFIG_DM_SPI_FLASH=y
++#CONFIG_SPI_FLASH_MTD=y
++#CONFIG_SPI_FLASH_WINBOND=y
++# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
++CONFIG_CMD_MTD=y
++#CONFIG_CMD_SF=y
++CONFIG_CMD_NAND=y
++CONFIG_CMD_NAND_TRIMFFS=y
++# CONFIG_ENABLE_NAND_NMBM is not set
+--- /dev/null
++++ b/arch/arm/dts/mt7986a-bpi-r3-emmc.dts
+@@ -0,0 +1,33 @@
++// SPDX-License-Identifier: GPL-2.0
++/*
++ * Copyright (c) 2021 MediaTek Inc.
++ * Author: Sam Shih <sam.shih at mediatek.com>
++ */
++
++/dts-v1/;
++#include "mt7986a-bpi-r3-sd.dts"
++#include <dt-bindings/gpio/gpio.h>
++/ {
++ reg_1p8v: regulator-1p8v {
++ compatible = "regulator-fixed";
++ regulator-name = "fixed-1.8V";
++ regulator-min-microvolt = <1800000>;
++ regulator-max-microvolt = <1800000>;
++ regulator-boot-on;
++ regulator-always-on;
++ };
++};
++
++&mmc0 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&mmc0_pins_default>;
++ bus-width = <8>;
++ max-frequency = <200000000>;
++ cap-mmc-highspeed;
++ cap-mmc-hw-reset;
++ vmmc-supply = <®_3p3v>;
++ vqmmc-supply = <®_1p8v>;
++ non-removable;
++ status = "okay";
++};
++
+--- /dev/null
++++ b/arch/arm/dts/mt7986a-bpi-r3-sd.dts
+@@ -0,0 +1,269 @@
++// SPDX-License-Identifier: GPL-2.0
++/*
++ * Copyright (c) 2021 MediaTek Inc.
++ * Author: Sam Shih <sam.shih at mediatek.com>
++ */
++
++/dts-v1/;
++#include "mt7986.dtsi"
++#include <dt-bindings/gpio/gpio.h>
++
++/ {
++ #address-cells = <1>;
++ #size-cells = <1>;
++ model = "BananaPi BPi-R3";
++ compatible = "mediatek,mt7986", "mediatek,mt7986-sd-rfb";
++
++ chosen {
++ stdout-path = &uart0;
++ tick-timer = &timer0;
++ };
++
++ reg_3p3v: regulator-3p3v {
++ compatible = "regulator-fixed";
++ regulator-name = "fixed-3.3V";
++ regulator-min-microvolt = <3300000>;
++ regulator-max-microvolt = <3300000>;
++ regulator-boot-on;
++ regulator-always-on;
++ };
++
++ keys {
++ compatible = "gpio-keys";
++
++ factory {
++ label = "reset";
++ gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
++ };
++
++ wps {
++ label = "wps";
++ gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
++ };
++ };
++
++ leds {
++ compatible = "gpio-leds";
++
++ led_status_green: green {
++ label = "green:status";
++ gpios = <&gpio 69 GPIO_ACTIVE_HIGH>;
++ };
++
++ led_status_blue: blue {
++ label = "blue:status";
++ gpios = <&gpio 86 GPIO_ACTIVE_HIGH>;
++ };
++ };
++
++};
++
++&uart0 {
++ status = "okay";
++};
++
++&uart1 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&uart1_pins>;
++ status = "disabled";
++};
++
++ð {
++ status = "okay";
++ mediatek,gmac-id = <0>;
++ phy-mode = "sgmii";
++ mediatek,switch = "mt7531";
++ reset-gpios = <&gpio 5 GPIO_ACTIVE_HIGH>;
++
++ fixed-link {
++ speed = <1000>;
++ full-duplex;
++ };
++};
++
++&pinctrl {
++ spic_pins: spi1-pins-func-1 {
++ mux {
++ function = "spi";
++ groups = "spi1_2";
++ };
++ };
++
++ uart1_pins: spi1-pins-func-3 {
++ mux {
++ function = "uart";
++ groups = "uart1_2";
++ };
++ };
++
++ pwm_pins: pwm0-pins-func-1 {
++ mux {
++ function = "pwm";
++ groups = "pwm0";
++ };
++ };
++
++ mmc0_pins_default: mmc0default {
++ mux {
++ function = "flash";
++ groups = "emmc_51";
++ };
++
++ conf-cmd-dat {
++ pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
++ "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
++ "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
++ input-enable;
++ drive-strength = <MTK_DRIVE_4mA>;
++ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
++ };
++
++ conf-clk {
++ pins = "EMMC_CK";
++ drive-strength = <MTK_DRIVE_6mA>;
++ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
++ };
++
++ conf-dsl {
++ pins = "EMMC_DSL";
++ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
++ };
++
++ conf-rst {
++ pins = "EMMC_RSTB";
++ drive-strength = <MTK_DRIVE_4mA>;
++ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
++ };
++ };
++
++ spi_flash_pins: spi0-pins-func-1 {
++ mux {
++ function = "flash";
++ groups = "spi0", "spi0_wp_hold";
++ };
++
++ conf-pu {
++ pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
++ drive-strength = <MTK_DRIVE_8mA>;
++ bias-pull-up = <MTK_PUPD_SET_R1R0_00>;
++ };
++
++ conf-pd {
++ pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
++ drive-strength = <MTK_DRIVE_8mA>;
++ bias-pull-down = <MTK_PUPD_SET_R1R0_00>;
++ };
++ };
++};
++
++&pwm {
++ pinctrl-names = "default";
++ pinctrl-0 = <&pwm_pins>;
++ status = "okay";
++};
++
++&spi0 {
++ #address-cells = <1>;
++ #size-cells = <0>;
++ pinctrl-names = "default";
++ pinctrl-0 = <&spi_flash_pins>;
++ status = "okay";
++ must_tx;
++ enhance_timing;
++ dma_ext;
++ ipm_design;
++ support_quad;
++ tick_dly = <1>;
++ sample_sel = <0>;
++
++ spi_nor at 0 {
++ compatible = "jedec,spi-nor";
++ reg = <0>;
++ spi-max-frequency = <52000000>;
++
++ partitions {
++ compatible = "fixed-partitions";
++ #address-cells = <1>;
++ #size-cells = <1>;
++
++ partition at 0 {
++ label = "bl2";
++ reg = <0x0 0x40000>;
++ };
++
++ partition at 40000 {
++ label = "u-boot-env";
++ reg = <0x40000 0x40000>;
++ };
++
++ partition at 80000 {
++ label = "reserved";
++ reg = <0x80000 0x80000>;
++ };
++
++ partition at 100000 {
++ label = "fip";
++ reg = <0x100000 0x80000>;
++ };
++
++ partition at 180000 {
++ label = "recovery";
++ reg = <0x180000 0xa80000>;
++ };
++
++ partition at c00000 {
++ label = "fit";
++ reg = <0xc00000 0x1400000>;
++ };
++ };
++ };
++
++ spi_nand at 1 {
++ compatible = "spi-nand";
++ reg = <1>;
++ spi-max-frequency = <52000000>;
++
++ partitions {
++ compatible = "fixed-partitions";
++ #address-cells = <1>;
++ #size-cells = <1>;
++
++ partition at 0 {
++ label = "bl2";
++ reg = <0x0 0x80000>;
++ };
++
++ partition at 80000 {
++ label = "factory";
++ reg = <0x80000 0x300000>;
++ };
++
++ partition at 380000 {
++ label = "fip";
++ reg = <0x380000 0x200000>;
++ };
++
++ partition at 580000 {
++ label = "ubi";
++ reg = <0x580000 0x7a80000>;
++ };
++ };
++ };
++};
++
++&watchdog {
++ status = "disabled";
++};
++
++&mmc0 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&mmc0_pins_default>;
++ bus-width = <4>;
++ max-frequency = <52000000>;
++ cap-sd-highspeed;
++ r_smpl = <1>;
++ vmmc-supply = <®_3p3v>;
++ vqmmc-supply = <®_3p3v>;
++ status = "okay";
++};
++
+--- /dev/null
++++ b/bananapi_bpi-r3_sdmmc_env
+@@ -0,0 +1,75 @@
++ipaddr=192.168.1.1
++serverip=192.168.1.254
++loadaddr=0x46000000
++console=earlycon=uart8250,mmio32,0x11002000 console=ttyS0
++bootargs=root=/dev/mmcblk0p65
++bootcmd=if pstore check ; then run boot_recovery ; else run boot_sdmmc ; fi
++bootconf=config-mt7986a-bananapi-bpi-r3
++bootdelay=0
++bootfile=openwrt-mediatek-filogic-bananapi_bpi-r3-initramfs-recovery.itb
++bootfile_upg=openwrt-mediatek-filogic-bananapi_bpi-r3-squashfs-sysupgrade.itb
++bootled_pwr=green:status
++bootled_rec=blue:status
++bootmenu_confirm_return=askenv - Press ENTER to return to menu ; bootmenu 60
++bootmenu_default=0
++bootmenu_delay=0
++bootmenu_title= [0;34m( ( ( [1;39mOpenWrt[0;34m ) ) ) [0;36m[SD card][0m
++bootmenu_0=Initialize environment.=run _firstboot
++bootmenu_0d=Run default boot command.=run boot_default
++bootmenu_1=Boot system via TFTP.=run boot_tftp ; run bootmenu_confirm_return
++bootmenu_2=Boot production system from SD card.=run boot_production ; run bootmenu_confirm_return
++bootmenu_3=Boot recovery system from SD card.=run boot_recovery ; run bootmenu_confirm_return
++bootmenu_4=Load production system via TFTP then write to SD card.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_production ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
++bootmenu_5=Load recovery system via TFTP then write to SD card.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_recovery ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
++bootmenu_6=[31mInstall bootloader, recovery and production to NOR.[0m=if sf probe ; then run nor_init ; else echo "NOR not detected" ; fi ; run bootmenu_confirm_return
++bootmenu_7=[31mInstall bootloader, recovery and production to NAND.[0m=if nand info ; then run ubi_init ; else echo "NAND not detected" ; fi ; run bootmenu_confirm_return
++bootmenu_8=Reboot.=reset
++bootmenu_9=Reset all settings to factory defaults.=run reset_factory ; reset
++boot_update_conf=if nand info ; then setenv bootconf config-mt7986a-bananapi-bpi-r3-snand ; else if sf probe ; then setenv bootconf config-mt7986a-bananapi-bpi-r3-nor ; else setenv bootconf config-mt7986a-bananapi-bpi-r3 ; fi ; fi
++boot_first=if button reset ; then led $bootled_rec on ; run boot_tftp_recovery ; setenv flag_recover 1 ; run boot_default ; fi ; bootmenu
++boot_default=if env exists flag_recover ; then else run bootcmd ; fi ; run boot_recovery ; setenv replacevol 1 ; run boot_tftp_forever
++boot_production=led $bootled_pwr on ; run boot_update_conf ; run sdmmc_read_production && bootm $loadaddr#$bootconf ; led $bootled_pwr off
++boot_recovery=led $bootled_rec on ; run boot_update_conf ; run sdmmc_read_recovery && bootm $loadaddr#$bootconf ; led $bootled_rec off
++boot_sdmmc=run boot_production ; run boot_recovery
++boot_tftp_forever=led $bootled_rec on ; while true ; do run boot_tftp_recovery ; sleep 1 ; done
++boot_tftp_production=run boot_update_conf ; tftpboot $loadaddr $bootfile_upg && env exists replacevol && iminfo $loadaddr && run sdmmc_write_production ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
++boot_tftp_recovery=run boot_update_conf ; tftpboot $loadaddr $bootfile && env exists replacevol && iminfo $loadaddr && run sdmmc_write_recovery ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
++boot_tftp=run boot_update_conf ; tftpboot $loadaddr $bootfile && bootm $loadaddr#$bootconf
++mmc_write_vol=imszb $loadaddr image_size && test 0x$image_size -le 0x$part_size && mmc erase 0x$part_addr 0x$part_size && mmc write $loadaddr 0x$part_addr 0x$image_size
++mmc_read_vol=mmc read $loadaddr $part_addr 0x8 && imszb $loadaddr image_size && test 0x$image_size -le 0x$part_size && mmc read $loadaddr 0x$part_addr 0x$image_size && setexpr filesize $image_size * 0x200
++part_default=production
++part_recovery=recovery
++reset_factory=eraseenv && reset
++sdmmc_read_production=part start mmc 0 $part_default part_addr && part size mmc 0 $part_default part_size && run mmc_read_vol
++sdmmc_read_recovery=part start mmc 0 $part_recovery part_addr && part size mmc 0 $part_recovery part_size && run mmc_read_vol
++sdmmc_read_snand_bl2=part start mmc 0 install part_addr && mmc read $loadaddr $part_addr 0x400
++sdmmc_read_snand_fip=part start mmc 0 install part_addr && setexpr offset $part_addr + 0x800 && mmc read $loadaddr $offset 0x1000
++sdmmc_read_nor_bl2=part start mmc 0 install part_addr && setexpr offset $part_addr + 0x2800 && mmc read $loadaddr $offset 0x400
++sdmmc_read_nor_fip=part start mmc 0 install part_addr && setexpr offset $part_addr + 0x3000 && mmc read $loadaddr $offset 0x1000
++sdmmc_read_emmc_install=part start mmc 0 install part_addr && setexpr offset $part_addr + 0x3800 && mmc read $loadaddr $offset 0x4000
++sdmmc_write_production=part start mmc 0 $part_default part_addr && part size mmc 0 $part_default part_size && run mmc_write_vol
++sdmmc_write_recovery=part start mmc 0 $part_recovery part_addr && part size mmc 0 $part_recovery part_size && run mmc_write_vol
++mtd_write_fip=mtd erase fip && mtd write fip $loadaddr
++mtd_write_bl2=mtd erase bl2 && mtd write bl2 $loadaddr
++nor_pad_size=imsz $loadaddr image_size ; setexpr image_eb 0x$image_size / 0x10000 ; setexpr tmp1 0x$image_size % 0x10000 ; test 0x$tmp1 -gt 0 && setexpr image_eb 0x$image_eb + 1 ; setexpr image_eb $image_eb * 0x10000
++nor_erase_env=mtd erase u-boot-env
++nor_write_production=run nor_pad_size ; test 0x$image_eb -le 0x3000000 && mtd erase fit && mtd write fit $loadaddr 0x0 $image_eb
++nor_write_recovery=run nor_pad_size ; test 0x$image_eb -le 0x900000 && mtd erase recovery 0x0 0x$image_eb && mtd write recovery $loadaddr 0x0 $image_eb
++nor_init=run nor_init_bl && run nor_init_openwrt
++nor_init_bl=run sdmmc_read_nor_bl2 && run mtd_write_bl2 && run sdmmc_read_nor_fip && run mtd_write_fip && run nor_erase_env
++nor_init_openwrt=run sdmmc_read_recovery && iminfo $loadaddr && run nor_write_recovery ; run sdmmc_read_production && iminfo $loadaddr && run nor_write_production
++ubi_create_env=ubi create ubootenv 0x100000 dynamic 0 ; ubi create ubootenv2 0x100000 dynamic 1
++ubi_format=ubi detach ; mtd erase ubi && ubi part ubi
++ubi_init=run ubi_init_bl && run ubi_format && run ubi_create_env && run ubi_init_openwrt && run ubi_init_emmc_install
++ubi_init_openwrt=run sdmmc_read_recovery && iminfo $loadaddr && run ubi_write_recovery ; run sdmmc_read_production && iminfo $loadaddr && run ubi_write_production
++ubi_init_bl=run sdmmc_read_snand_bl2 && run mtd_write_bl2 && run sdmmc_read_snand_fip && run mtd_write_fip
++ubi_init_emmc_install=run sdmmc_read_emmc_install && run ubi_write_emmc_install
++ubi_prepare_rootfs=if ubi check rootfs_data ; then else if env exists rootfs_data_max ; then ubi create rootfs_data $rootfs_data_max dynamic || ubi create rootfs_data - dynamic ; else ubi create rootfs_data - dynamic ; fi ; fi
++ubi_remove_rootfs=ubi check rootfs_data && ubi remove rootfs_data
++ubi_write_emmc_install=ubi check emmc_install && ubi remote emmc_install ; ubi create emmc_install 0x800000 dynamic ; ubi write $loadaddr emmc_install 0x800000
++ubi_write_production=ubi check fit && ubi remove fit ; run ubi_remove_rootfs ; ubi create fit $filesize dynamic 2 && ubi write $loadaddr fit $filesize
++ubi_write_recovery=ubi check recovery && ubi remove recovery ; run ubi_remove_rootfs ; ubi create recovery $filesize dynamic 3 && ubi write $loadaddr recovery $filesize
++_init_env=setenv _init_env ; setenv _create_env ; saveenv ; saveenv
++_firstboot=setenv _firstboot ; run _switch_to_menu ; run _init_env ; run boot_first
++_switch_to_menu=setenv _switch_to_menu ; setenv bootdelay 3 ; setenv bootmenu_delay 3 ; setenv bootmenu_0 $bootmenu_0d ; setenv bootmenu_0d ; run _bootmenu_update_title
++_bootmenu_update_title=setenv _bootmenu_update_title ; setenv bootmenu_title "$bootmenu_title [33m$ver[0m"
+--- /dev/null
++++ b/bananapi_bpi-r3_nor_env
+@@ -0,0 +1,55 @@
++ipaddr=192.168.1.1
++serverip=192.168.1.254
++loadaddr=0x46000000
++console=earlycon=uart8250,mmio32,0x11002000 console=ttyS0
++bootargs=root=/dev/mtdblock0p1
++bootcmd=if pstore check ; then run boot_recovery ; else run boot_nor ; fi
++bootconf=config-mt7986a-bananapi-bpi-r3-emmc-nor
++bootdelay=0
++bootfile=openwrt-mediatek-filogic-bananapi_bpi-r3-initramfs-recovery.itb
++bootfile_bl2=openwrt-mediatek-filogic-bananapi_bpi-r3-nor-preloader.bin
++bootfile_fip=openwrt-mediatek-filogic-bananapi_bpi-r3-nor-bl31-uboot.fip
++bootfile_upg=openwrt-mediatek-filogic-bananapi_bpi-r3-squashfs-sysupgrade.itb
++bootled_pwr=green:status
++bootled_rec=blue:status
++bootmenu_confirm_return=askenv - Press ENTER to return to menu ; bootmenu 60
++bootmenu_default=0
++bootmenu_delay=0
++bootmenu_title= [0;34m( ( ( [1;39mOpenWrt[0;34m ) ) ) [0;36m[SPI-NOR][0m
++bootmenu_0=Initialize environment.=run _firstboot
++bootmenu_0d=Run default boot command.=run boot_default
++bootmenu_1=Boot system via TFTP.=run boot_tftp ; run bootmenu_confirm_return
++bootmenu_2=Boot production system from flash.=run boot_production ; run bootmenu_confirm_return
++bootmenu_3=Boot recovery system from flash.=run boot_recovery ; run bootmenu_confirm_return
++bootmenu_4=Load production system via TFTP then write to flash.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_production ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
++bootmenu_5=Load recovery system via TFTP then write to flash.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_recovery ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
++bootmenu_6=[31mLoad BL31+U-Boot FIP via TFTP then write to flash.[0m=run boot_tftp_write_fip ; run bootmenu_confirm_return
++bootmenu_7=[31mLoad BL2 preloader via TFTP then write to flash.[0m=run boot_tftp_write_preloader ; run bootmenu_confirm_return
++bootmenu_8=Reboot.=reset
++bootmenu_9=Reset all settings to factory defaults.=run reset_factory ; reset
++boot_first=if button reset ; then led $bootled_rec on ; run boot_tftp_recovery ; setenv flag_recover 1 ; run boot_default ; fi ; bootmenu
++boot_default=if env exists flag_recover ; then else run bootcmd ; fi ; run boot_recovery ; setenv replacevol 1 ; run boot_tftp_forever
++boot_production=run boot_update_conf ; led $bootled_pwr on ; run nor_read_production && bootm $loadaddr#$bootconf ; led $bootled_pwr off
++boot_recovery=run boot_update_conf ; led $bootled_rec on ; run nor_read_recovery ; bootm $loadaddr#$bootconf ; led $bootled_rec off
++boot_serial_write_fip=loadx $loadaddr 115200 && run boot_write_fip
++boot_serial_write_preloader=loadx $loadaddr 115200 && run boot_write_preloader
++boot_tftp_forever=led $bootled_rec on ; while true ; do run boot_tftp_recovery ; sleep 1 ; done
++boot_tftp_production=run boot_update_conf ; tftpboot $loadaddr $bootfile_upg && env exists replacevol && iminfo $loadaddr && run nor_write_production ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
++boot_tftp_recovery=run boot_update_conf ; tftpboot $loadaddr $bootfile && env exists replacevol && iminfo $loadaddr && run nor_write_recovery ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
++boot_tftp=run boot_update_conf ; tftpboot $loadaddr $bootfile && bootm $loadaddr#$bootconf
++boot_tftp_write_fip=tftpboot $loadaddr $bootfile_fip && run boot_write_fip
++boot_tftp_write_preloader=tftpboot $loadaddr $bootfile_bl2 && run boot_write_preloader
++boot_update_conf=if mmc partconf 0 ; then setenv bootconf config-mt7986a-bananapi-bpi-r3-emmc-nor ; else setenv bootconf config-mt7986a-bananapi-bpi-r3-nor ; fi
++boot_nor=run boot_production ; run boot_recovery
++boot_write_fip=mtd erase fip && mtd write fip $loadaddr
++boot_write_preloader=mtd erase bl2 && mtd write bl2 $loadaddr
++reset_factory=mtd erase u-boot-env
++nor_read_production=mtd read fit $loadaddr 0x0 0x1000 && imsz $loadaddr image_size && mtd read fit $loadaddr 0x0 $image_size
++nor_read_recovery=mtd read recovery $loadaddr 0x0 0x1000 && imsz $loadaddr image_size && mtd read recovery $loadaddr 0x0 $image_size
++nor_pad_size=imsz $loadaddr image_size ; setexpr image_eb 0x$image_size / 0x10000 ; setexpr tmp1 0x$image_size % 0x10000 ; test 0x$tmp1 -gt 0 && setexpr image_eb 0x$image_eb + 1 ; setexpr image_eb $image_eb * 0x10000
++nor_write_production=run nor_pad_size ; test 0x$image_eb -le 0x3000000 && mtd erase fit && mtd write fit $loadaddr 0x0 $image_eb
++nor_write_recovery=run nor_pad_size ; test 0x$image_eb -le 0x900000 && mtd erase recovery 0x0 0x$image_eb && mtd write recovery $loadaddr 0x0 $image_eb
++_init_env=setenv _init_env ; saveenv
++_firstboot=setenv _firstboot ; run _switch_to_menu ; run _init_env ; run boot_first
++_switch_to_menu=setenv _switch_to_menu ; setenv bootdelay 3 ; setenv bootmenu_delay 3 ; setenv bootmenu_0 $bootmenu_0d ; setenv bootmenu_0d ; run _bootmenu_update_title
++_bootmenu_update_title=setenv _bootmenu_update_title ; setenv bootmenu_title "$bootmenu_title [33m$ver[0m"
+--- /dev/null
++++ b/bananapi_bpi-r3_snand_env
+@@ -0,0 +1,69 @@
++ipaddr=192.168.1.1
++serverip=192.168.1.254
++loadaddr=0x46000000
++console=earlycon=uart8250,mmio32,0x11002000 console=ttyS0
++bootargs=root=/dev/ubiblock0_2p1
++bootconf=config-mt7986a-bananapi-bpi-r3-snand
++bootcmd=if pstore check ; then run boot_recovery ; else run boot_ubi ; fi
++bootdelay=0
++bootfile=openwrt-mediatek-filogic-bananapi_bpi-r3-initramfs-recovery.itb
++bootfile_bl2=openwrt-mediatek-filogic-bananapi_bpi-r3-snand-preloader.bin
++bootfile_fip=openwrt-mediatek-filogic-bananapi_bpi-r3-snand-bl31-uboot.fip
++bootfile_upg=openwrt-mediatek-filogic-bananapi_bpi-r3-squashfs-sysupgrade.itb
++bootled_pwr=green:status
++bootled_rec=blue:status
++bootmenu_confirm_return=askenv - Press ENTER to return to menu ; bootmenu 60
++bootmenu_default=0
++bootmenu_delay=0
++bootmenu_title= [0;34m( ( ( [1;39mOpenWrt[0;34m ) ) ) [0;36m[SPI-NAND][0m
++bootmenu_0=Initialize environment.=run _firstboot
++bootmenu_0d=Run default boot command.=run boot_default
++bootmenu_1=Boot system via TFTP.=run boot_tftp ; run bootmenu_confirm_return
++bootmenu_2=Boot production system from NAND.=run boot_production ; run bootmenu_confirm_return
++bootmenu_3=Boot recovery system from NAND.=run boot_recovery ; run bootmenu_confirm_return
++bootmenu_4=Load production system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_production ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
++bootmenu_5=Load recovery system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_recovery ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
++bootmenu_6=[31mLoad BL31+U-Boot FIP via TFTP then write to NAND.[0m=run boot_tftp_write_fip ; run bootmenu_confirm_return
++bootmenu_7=[31mLoad BL2 preloader via TFTP then write to NAND.[0m=run boot_tftp_write_bl2 ; run bootmenu_confirm_return
++bootmenu_8=[31mInstall bootloader, recovery and production to eMMC.[0m=if mmc partconf 0 ; then run emmc_init ; else echo "eMMC not detected" ; fi ; run bootmenu_confirm_return
++bootmenu_9=Reboot.=reset
++bootmenu_10=Reset all settings to factory defaults.=run reset_factory ; reset
++boot_first=if button reset ; then led $bootled_rec on ; run boot_tftp_recovery ; setenv flag_recover 1 ; run boot_default ; fi ; bootmenu
++boot_default=if env exists flag_recover ; then else run bootcmd ; fi ; run boot_recovery ; setenv replacevol 1 ; run boot_tftp_forever
++boot_production=run boot_update_conf ; led $bootled_pwr on ; run ubi_read_production && bootm $loadaddr#$bootconf ; led $bootled_pwr off
++boot_recovery=run boot_update_conf ; led $bootled_rec on ; run ubi_read_recovery && bootm $loadaddr#$bootconf ; led $bootled_rec off
++boot_ubi=run boot_update_conf ; run boot_production ; run boot_recovery
++boot_tftp_forever=led $bootled_rec on ; while true ; do run boot_tftp_recovery ; sleep 1 ; done
++boot_tftp_production=run boot_update_conf ; tftpboot $loadaddr $bootfile_upg && env exists replacevol && iminfo $loadaddr && run ubi_write_production ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
++boot_tftp_recovery=run boot_update_conf ; tftpboot $loadaddr $bootfile && env exists replacevol && iminfo $loadaddr && run ubi_write_recovery ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
++boot_tftp=run boot_update_conf ; tftpboot $loadaddr $bootfile && bootm $loadaddr#$bootconf
++boot_tftp_write_fip=tftpboot $loadaddr $bootfile_fip && run mtd_write_fip && run reset_factory
++boot_tftp_write_bl2=tftpboot $loadaddr $bootfile_bl2 && run mtd_write_bl2
++boot_update_conf=if mmc partconf 0 ; then setenv bootconf config-mt7986a-bananapi-bpi-r3-emmc-snand ; else setenv bootconf config-mt7986a-bananapi-bpi-r3-snand ; fi
++part_default=production
++part_recovery=recovery
++reset_factory=ubi part ubi ; mw $loadaddr 0x0 0x800 ; ubi write $loadaddr ubootenv 0x800 ; ubi write $loadaddr ubootenv2 0x800
++mtd_write_fip=mtd erase fip && mtd write fip $loadaddr
++mtd_write_bl2=mtd erase bl2 && mtd write bl2 $loadaddr
++ubi_create_env=ubi check ubootenv || ubi create ubootenv 0x100000 dynamic 0 ; ubi check ubootenv2 || ubi create ubootenv2 0x100000 dynamic 1
++ubi_format=ubi detach ; mtd erase ubi && ubi part ubi ; reset
++ubi_prepare_rootfs=if ubi check rootfs_data ; then else if env exists rootfs_data_max ; then ubi create rootfs_data $rootfs_data_max dynamic || ubi create rootfs_data - dynamic ; else ubi create rootfs_data - dynamic ; fi ; fi
++ubi_read_production=ubi read $loadaddr fit && iminfo $loadaddr && run ubi_prepare_rootfs
++ubi_read_recovery=ubi check recovery && ubi read $loadaddr recovery
++ubi_read_emmc_install=ubi check emmc_install && ubi read $loadaddr emmc_install
++ubi_remove_rootfs=ubi check rootfs_data && ubi remove rootfs_data
++ubi_write_production=ubi check fit && ubi remove fit ; run ubi_remove_rootfs ; ubi create fit $filesize dynamic 2 && ubi write $loadaddr fit $filesize
++ubi_write_recovery=ubi check recovery && ubi remove recovery ; run ubi_remove_rootfs ; ubi create recovery $filesize dynamic 3 && ubi write $loadaddr recovery $filesize
++mmc_write_vol=imszb $loadaddr image_size && test 0x$image_size -le 0x$part_size && mmc erase 0x$part_addr 0x$part_size && mmc write $loadaddr 0x$part_addr 0x$image_size
++emmc_init=mmc dev 0 && mmc bootbus 0 0 0 0 && run emmc_init_bl && run emmc_init_openwrt ; env default bootcmd ; saveenv ; saveenv
++emmc_init_bl=run ubi_read_emmc_install && setenv fileaddr $loadaddr && run emmc_write_bl2 && setexpr fileaddr $loadaddr + 0x100000 && run emmc_write_fip && setexpr fileaddr $loadaddr + 0x500000 && run emmc_write_hdr
++emmc_init_openwrt=run ubi_read_recovery && iminfo $loadaddr && run emmc_write_recovery ; run ubi_read_production && iminfo $loadaddr && run emmc_write_production
++emmc_write_bl2=mmc partconf 0 1 1 1 && mmc erase 0x0 0x400 && mmc write $fileaddr 0x0 0x400 ; mmc partconf 0 1 1 0
++emmc_write_fip=mmc erase 0x3400 0x2000 && mmc write $fileaddr 0x3400 0x2000 && mmc erase 0x2000 0x800
++emmc_write_hdr=mmc erase 0x0 0x40 && mmc write $fileaddr 0x0 0x40
++emmc_write_production=part start mmc 0 $part_default part_addr && part size mmc 0 $part_default part_size && run mmc_write_vol
++emmc_write_recovery=part start mmc 0 $part_recovery part_addr && part size mmc 0 $part_recovery part_size && run mmc_write_vol
++_init_env=setenv _init_env ; run ubi_create_env ; saveenv ; saveenv
++_firstboot=setenv _firstboot ; run _switch_to_menu ; run _init_env ; run boot_first
++_switch_to_menu=setenv _switch_to_menu ; setenv bootdelay 3 ; setenv bootmenu_delay 3 ; setenv bootmenu_0 $bootmenu_0d ; setenv bootmenu_0d ; run _bootmenu_update_title
++_bootmenu_update_title=setenv _bootmenu_update_title ; setenv bootmenu_title "$bootmenu_title [33m$ver[0m"
+--- /dev/null
++++ b/bananapi_bpi-r3_emmc_env
+@@ -0,0 +1,56 @@
++ipaddr=192.168.1.1
++serverip=192.168.1.254
++loadaddr=0x46000000
++console=earlycon=uart8250,mmio32,0x11002000 console=ttyS0
++bootargs=root=/dev/mmcblk0p65
++bootcmd=if pstore check ; then run boot_recovery ; else run boot_emmc ; fi
++bootconf=config-mt7986a-bananapi-bpi-r3-emmc
++bootdelay=0
++bootfile=openwrt-mediatek-filogic-bananapi_bpi-r3-initramfs-recovery.itb
++bootfile_bl2=openwrt-mediatek-filogic-bananapi_bpi-r3-emmc-preloader.bin
++bootfile_fip=openwrt-mediatek-filogic-bananapi_bpi-r3-emmc-bl31-uboot.fip
++bootfile_upg=openwrt-mediatek-filogic-bananapi_bpi-r3-squashfs-sysupgrade.itb
++bootled_pwr=green:status
++bootled_rec=blue:status
++bootmenu_confirm_return=askenv - Press ENTER to return to menu ; bootmenu 60
++bootmenu_default=0
++bootmenu_delay=0
++bootmenu_title= [0;34m( ( ( [1;39mOpenWrt[0;34m ) ) ) [0;36m[eMMC][0m
++bootmenu_0=Initialize environment.=run _firstboot
++bootmenu_0d=Run default boot command.=run boot_default
++bootmenu_1=Boot system via TFTP.=run boot_tftp ; run bootmenu_confirm_return
++bootmenu_2=Boot production system from eMMC.=run boot_production ; run bootmenu_confirm_return
++bootmenu_3=Boot recovery system from eMMC.=run boot_recovery ; run bootmenu_confirm_return
++bootmenu_4=Load production system via TFTP then write to eMMC.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_production ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
++bootmenu_5=Load recovery system via TFTP then write to eMMC.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_recovery ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
++bootmenu_6=[31mLoad BL31+U-Boot FIP via TFTP then write to eMMC.[0m=run boot_tftp_write_fip ; run bootmenu_confirm_return
++bootmenu_7=[31mLoad BL2 preloader via TFTP then write to eMMC.[0m=run boot_tftp_write_bl2 ; run bootmenu_confirm_return
++bootmenu_8=Reboot.=reset
++bootmenu_9=Reset all settings to factory defaults.=run reset_factory ; reset
++boot_first=if button reset ; then led $bootled_rec on ; run boot_tftp_recovery ; setenv flag_recover 1 ; run boot_default ; fi ; bootmenu
++boot_default=if env exists flag_recover ; then else run bootcmd ; fi ; run boot_recovery ; setenv replacevol 1 ; run boot_tftp_forever
++boot_production=run boot_update_conf ; led $bootled_pwr on ; run emmc_read_production && bootm $loadaddr#$bootconf ; led $bootled_pwr off
++boot_recovery=run boot_update_conf ; led $bootled_rec on ; run emmc_read_recovery && bootm $loadaddr#$bootconf ; led $bootled_rec off
++boot_emmc=run boot_update_conf ; run boot_production ; run boot_recovery
++boot_tftp_forever=led $bootled_rec on ; while true ; do run boot_tftp_recovery ; sleep 1 ; done
++boot_tftp_production=run boot_update_conf ; tftpboot $loadaddr $bootfile_upg && env exists replacevol && iminfo $loadaddr && run emmc_write_production ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
++boot_tftp_recovery=run boot_update_conf ; tftpboot $loadaddr $bootfile && env exists replacevol && iminfo $loadaddr && run emmc_write_recovery ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
++boot_tftp_write_fip=tftpboot $loadaddr $bootfile_fip && run emmc_write_fip
++boot_tftp_write_bl2=tftpboot $loadaddr $bootfile_bl2 && run emmc_write_bl2
++boot_tftp=run boot_update_conf ; tftpboot $loadaddr $bootfile && bootm $loadaddr#$bootconf
++boot_update_conf=if nand info ; then setenv bootconf config-mt7986a-bananapi-bpi-r3-emmc-snand ; else setenv bootconf config-mt7986a-bananapi-bpi-r3-emmc-nor ; fi
++mmc_write_vol=imszb $loadaddr image_size && test 0x$image_size -le 0x$part_size && mmc erase 0x$part_addr 0x$part_size && mmc write $loadaddr 0x$part_addr 0x$image_size
++mmc_read_vol=mmc read $loadaddr $part_addr 0x8 && imszb $loadaddr image_size && test 0x$image_size -le 0x$part_size && mmc read $loadaddr 0x$part_addr 0x$image_size && setexpr filesize $image_size * 0x200
++part_default=production
++part_recovery=recovery
++reset_factory=eraseenv && reset
++emmc_read_production=part start mmc 0 $part_default part_addr && part size mmc 0 $part_default part_size && run mmc_read_vol
++emmc_read_recovery=part start mmc 0 $part_recovery part_addr && part size mmc 0 $part_recovery part_size && run mmc_read_vol
++emmc_write_bl2=mmc partconf 0 1 1 1 && mmc erase 0x0 0x400 && mmc write $fileaddr 0x0 0x400 ; mmc partconf 0 1 1 0
++emmc_write_fip=mmc erase 0x3400 0x2000 && mmc write $fileaddr 0x3400 0x2000 && mmc erase 0x2000 0x800
++emmc_write_production=part start mmc 0 $part_default part_addr && part size mmc 0 $part_default part_size && run mmc_write_vol
++emmc_write_recovery=part start mmc 0 $part_recovery part_addr && part size mmc 0 $part_recovery part_size && run mmc_write_vol
++_init_env=setenv _init_env ; setenv _create_env ; saveenv ; saveenv
++_firstboot=setenv _firstboot ; run _switch_to_menu ; run _init_env ; run boot_first
++_switch_to_menu=setenv _switch_to_menu ; setenv bootdelay 3 ; setenv bootmenu_delay 3 ; setenv bootmenu_0 $bootmenu_0d ; setenv bootmenu_0d ; run _bootmenu_update_title
++_bootmenu_update_title=setenv _bootmenu_update_title ; setenv bootmenu_title "$bootmenu_title [33m$ver[0m"
More information about the lede-commits
mailing list