[openwrt/openwrt] ramips: add support for Sitecom WLR-4100 v1 002
LEDE Commits
lede-commits at lists.infradead.org
Sat Aug 27 23:21:28 PDT 2022
ynezz pushed a commit to openwrt/openwrt.git, branch openwrt-21.02:
https://git.openwrt.org/caeb618eea9c327d801f0e16eb3ed930f567481d
commit caeb618eea9c327d801f0e16eb3ed930f567481d
Author: Andrea Poletti <polex73 at yahoo.it>
AuthorDate: Fri Jul 23 18:15:00 2021 +0200
ramips: add support for Sitecom WLR-4100 v1 002
Sitecom WLR-4100 v1 002 (marked as X4 N300) is a wireless router
Specification:
SoC: MT7620A
RAM: 64 MB DDR2
Flash: MX25L6405D SPI NOR 8 MB
WIFI: 2.4 GHz integrated
Ethernet: 5x 10/100/1000 Mbps QCA8337
USB: 1x 2.0
LEDS: 2x GPIO controlled, 5x switch
Buttons: 1x GPIO controlled
UART: row of 4 unpopulated holes near USB port, starting count from
white triangle on PCB:
VCC 3.3V
GND
TX
RX
baud: 115200, parity: none, flow control: none
Installation
Connect to one of LAN (yellow) ethernet ports,
Open router configuration interface,
Go to Toolbox > Firmware,
Browse for OpenWrt factory image with dlf extension and hit Apply,
Wait few minutes, after the Power LED will stop blinking, the router is
ready for configuration.
Known issues
Some USB 2.0 devices work at full speed mode 1.1 only
MAC addresses
factory partition only contains one (binary) MAC address in 0x4.
u-boot-env contains four (ascii) MAC addresses, of which two appear
to be valid.
factory 0x4 **:**:**:**:b9:84 binary
u-boot-env ethaddr **:**:**:**:b9:84 ascii
u-boot-env wanaddr **:**:**:**:b9:85 ascii
u-boot-env wlanaddr 00:AA:BB:CC:DD:12 ascii
u-boot-env iNICaddr 00:AA:BB:CC:DD:22 ascii
The factory firmware only assigns ethaddr. Thus, we take the
binary value which we can use directly in DTS.
Additional information
OEM firmware shell password is: SitecomSenao
useful for creating backup of original firmware.
There is also another revision of this device (v1 001), based on RT3352 SoC
The nvmem feature (commit 06bb4a5) was introduced in master after the
splitting of the 21.02 branch. It need to be reverted in 21.02..
Signed-off-by: Andrea Poletti <polex73 at yahoo.it>
[remove config DT label, convert to nvmem, remove MAC address
setup from u-boot-env, add MAC address info to commit message]
Signed-off-by: Adrian Schmutzler <freifunk at adrianschmutzler.de>
(cherry picked from commit de0c380a5f8289839ab970e794a45f0e04a466a3)
Signed-off-by: Petr Štetiar <ynezz at true.cz>
---
package/boot/uboot-envtools/files/ramips | 3 +-
.../ramips/dts/mt7620a_sitecom_wlr-4100-v1-002.dts | 186 +++++++++++++++++++++
target/linux/ramips/image/mt7620.mk | 14 ++
.../mt7620/base-files/etc/board.d/02_network | 3 +-
4 files changed, 204 insertions(+), 2 deletions(-)
diff --git a/package/boot/uboot-envtools/files/ramips b/package/boot/uboot-envtools/files/ramips
index 0de062bd83..8d3ae88b48 100644
--- a/package/boot/uboot-envtools/files/ramips
+++ b/package/boot/uboot-envtools/files/ramips
@@ -18,7 +18,8 @@ alfa-network,awusfree1|\
alfa-network,quad-e4g|\
alfa-network,r36m-e4g|\
alfa-network,tube-e4g|\
-engenius,esr600h)
+engenius,esr600h|\
+sitecom,wlr-4100-v1-002)
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x1000" "0x1000"
;;
allnet,all0256n-4m|\
diff --git a/target/linux/ramips/dts/mt7620a_sitecom_wlr-4100-v1-002.dts b/target/linux/ramips/dts/mt7620a_sitecom_wlr-4100-v1-002.dts
new file mode 100644
index 0000000000..3b260c5b8d
--- /dev/null
+++ b/target/linux/ramips/dts/mt7620a_sitecom_wlr-4100-v1-002.dts
@@ -0,0 +1,186 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7620a.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "sitecom,wlr-4100-v1-002", "ralink,mt7620a-soc";
+ model = "Sitecom WLR-4100 v1 002";
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ };
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ label = "amber:power";
+ gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ wifi {
+ label = "blue:wifi";
+ gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+
+ wps {
+ label = "white:wps";
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ wps {
+ label = "wps";
+ gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ gpio_export {
+ compatible = "gpio-export";
+ #size-cells = <0>;
+
+ usb-power {
+ gpio-export,name = "usb-power";
+ gpio-export,output = <1>;
+ gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&gpio1 {
+ status = "okay";
+};
+
+&gpio3 {
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "uboot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition at 30000 {
+ label = "u-boot-env";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ factory: partition at 40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ partition at 50000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x50000 0x790000>;
+ };
+
+ partition at 7e0000 {
+ label = "backup";
+ reg = <0x7e0000 0x10000>;
+ read-only;
+ };
+
+ partition at 7f0000 {
+ label = "storage";
+ reg = <0x7f0000 0x10000>;
+ read-only;
+ };
+ };
+ };
+};
+
+ðernet {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii1_pins &mdio_pins>;
+
+ mtd-mac-address = <&factory 0x4>;
+
+ port at 5 {
+ status = "okay";
+
+ phy-mode = "rgmii";
+ mediatek,fixed-link = <1000 1 1 1>;
+ };
+
+ mdio-bus {
+ status = "okay";
+
+ ethernet-phy at 0 {
+ reg = <0>;
+ phy-mode = "rgmii";
+
+ qca,ar8327-initvals = <
+ 0x04 0x06200000 /* PORT0 PAD MODE CTRL */
+ 0x08 0x01000000 /* PORT5 PAD MODE CTRL RX delay EN all ports 0, 5, 6 */
+ 0x7c 0x0000007e /* PORT0_STATUS */
+ 0x94 0x00000000 /* PORT6_STATUS */
+ >;
+ };
+ };
+};
+
+&gsw {
+ mediatek,ephy-base = /bits/ 8 <8>;
+};
+
+&ehci {
+ status = "okay";
+};
+
+&ohci {
+ status = "okay";
+};
+
+&wmac {
+ status = "okay";
+
+ ralink,mtd-eeprom = <&factory 0x0>;
+};
+
+&state_default {
+ gpio {
+ groups = "uartf", "i2c", "wled", "spi refclk";
+ function = "gpio";
+ };
+};
+
diff --git a/target/linux/ramips/image/mt7620.mk b/target/linux/ramips/image/mt7620.mk
index 93fa8ae48d..1fc75974f6 100644
--- a/target/linux/ramips/image/mt7620.mk
+++ b/target/linux/ramips/image/mt7620.mk
@@ -963,6 +963,20 @@ define Device/sercomm_na930
endef
TARGET_DEVICES += sercomm_na930
+define Device/sitecom_wlr-4100-v1-002
+ SOC := mt7620a
+ BLOCKSIZE := 4k
+ IMAGE_SIZE := 7744k
+ IMAGES += factory.dlf
+ IMAGE/factory.dlf := $$(sysupgrade_bin) | check-size | \
+ senao-header -r 0x0222 -p 0x104A -t 2
+ DEVICE_VENDOR := Sitecom
+ DEVICE_MODEL := WLR-4100
+ DEVICE_VARIANT := v1 002
+ DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci uboot-envtools
+endef
+TARGET_DEVICES += sitecom_wlr-4100-v1-002
+
define Device/tplink_archer-c20i
$(Device/tplink-v2)
SOC := mt7620a
diff --git a/target/linux/ramips/mt7620/base-files/etc/board.d/02_network b/target/linux/ramips/mt7620/base-files/etc/board.d/02_network
index e867b58aed..07b17a9daf 100755
--- a/target/linux/ramips/mt7620/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/mt7620/base-files/etc/board.d/02_network
@@ -134,7 +134,8 @@ ramips_setup_interfaces()
ucidef_add_switch "switch1" \
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "6 at eth0"
;;
- engenius,esr600)
+ engenius,esr600|\
+ sitecom,wlr-4100-v1-002)
ucidef_add_switch "switch0" \
"1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan" "0 at eth0"
ucidef_add_switch "switch1" \
More information about the lede-commits
mailing list