[openwrt/openwrt] ath79: add support for TP-Link Deco M4R v1 and v2
LEDE Commits
lede-commits at lists.infradead.org
Sat Apr 30 15:54:26 PDT 2022
hauke pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/063e9047cc8b247ea4b04ee3248b99f3212a42f8
commit 063e9047cc8b247ea4b04ee3248b99f3212a42f8
Author: Foica David <superh552 at gmail.com>
AuthorDate: Thu Apr 21 04:20:57 2022 +0300
ath79: add support for TP-Link Deco M4R v1 and v2
This commit adds support for the TP-Link Deco M4R (it can also be M4,
TP-Link uses both names) v1 and v2. It is similar hardware-wise to the
Archer C6 v2. Software-wise it is very different. V2 has a bit different
layout from V1 but the chips are the same and the OEM firmware is the same
for both versions.
Specifications:
SoC: QCA9563-AL3A
RAM: Zentel A3R1GE40JBF
Wireless 2.4GHz: QCA9563-AL3A (main SoC)
Wireless 5GHz: QCA9886
Ethernet Switch: QCA8337N-AL3C
Flash: 16 MB SPI NOR
Flashing:
The device's bootloader only accepts images that are signed using
TP-Link's RSA key, therefore this way of flashing is not possible. The
device has a web GUI that should be accessible after setting up the device
using the app (it requires the app to set it up first because the web GUI
asks for the TP-Link account password) but for unknown reasons, the web
GUI also refuses custom images.
There is a debug firmware image that has been shared on the device's
OpenWrt forum thread that has telnet unlocked, which the bootloader will
accept because it is signed. It can be used to transfer an OpenWrt image
file over to the device and then be used with mtd to flash the device.
Pre-requisites:
- Debug firmware.
- A way of transferring the file to the router, you can use an FTP server
as an example.
- Set a static IP of 192.168.0.2/255.255.255.0 on your computer.
- OpenWrt image.
Installation:
- Unplug your router and turn it upside down. Using a long and thin object
like a SIM unlock tool, press and hold the reset button on the router and
replug it. Keep holding it until the LED flashes yellow.
- Open 192.168.0.1. You should see the bootloader recovery's webpage.
Choose the debug firmware that you downloaded and flash it. Wait until the
router reboots (at this stage you can remove the static IP).
- Open a terminal window and connect to the router via telnet (the primary
router should have a 192.168.0.1 IP address, secondary routers are
different).
- Transfer the file over to the router, you can use curl to download it
from the internet (use the insecure flag and make sure your source accepts
insecure downloads) or from an FTP server.
- The router's default mtd partition scheme has kernel and rootfs
separated. We can use dd to split the OpenWrt image file and flash it with
mtd:
dd if=openwrt.bin of=kernel.bin skip=0 count=8192 bs=256
dd if=openwrt.bin of=rootfs.bin skip=8192 bs=256
- Once the images are ready, you have to flash the device using mtd
(make sure to flash the correct partitions or you may be left with a
hard bricked router):
mtd write kernel.bin kernel
mtd write rootfs.bin rootfs
- Flashing is done, reboot the device now.
Signed-off-by: Foica David <superh552 at gmail.com>
---
.../linux/ath79/dts/qca9563_tplink_deco-m4r-v1.dts | 147 +++++++++++++++++++++
.../generic/base-files/etc/board.d/02_network | 4 +
.../etc/hotplug.d/firmware/11-ath10k-caldata | 6 +
target/linux/ath79/image/generic-tp-link.mk | 12 ++
4 files changed, 169 insertions(+)
diff --git a/target/linux/ath79/dts/qca9563_tplink_deco-m4r-v1.dts b/target/linux/ath79/dts/qca9563_tplink_deco-m4r-v1.dts
new file mode 100644
index 0000000000..26bb906910
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_tplink_deco-m4r-v1.dts
@@ -0,0 +1,147 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca956x.dtsi"
+
+/ {
+ compatible = "tplink,deco-m4r-v1", "qca,qca9563";
+ model = "TP-Link Deco M4R v1";
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ wlan2g {
+ label = "red:wlan2g";
+ gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+
+ led_power: power {
+ label = "green:power";
+ gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ wlan5g {
+ label = "blue:wlan5g";
+ gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+ };
+
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "Reset button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&mdio0 {
+ status = "okay";
+ phy-mask = <0>;
+
+ phy0: ethernet-phy at 0 {
+ reg = <0>;
+ phy-mode = "sgmii";
+ qca,mib-poll-interval = <500>;
+
+ qca,ar8327-initvals = <
+ 0x04 0x00080080 /* PORT0 PAD MODE CTRL */
+ 0x7c 0x0000007e /* PORT0_STATUS */
+ >;
+ };
+};
+
+&spi {
+ status = "okay";
+ num-cs = <1>;
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ uboot: partition at 0 {
+ label = "u-boot";
+ reg = <0x000000 0x080000>;
+ read-only;
+ };
+
+ partition at 80000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x080000 0xe00000>;
+ };
+
+ partition at e80000 {
+ label = "product-info";
+ reg = <0xe80000 0x05000>;
+ read-only;
+ };
+
+ config: partition at e85000 {
+ label = "config";
+ reg = <0xe85000 0x16b000>;
+ read-only;
+ };
+
+ art: partition at ff0000 {
+ label = "art";
+ reg = <0xff0000 0x010000>;
+ read-only;
+ };
+ };
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ phy-mode = "sgmii";
+ phy-handle = <&phy0>;
+
+ nvmem-cells = <&macaddr_config_8>;
+ nvmem-cell-names = "mac-address";
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x1000>;
+ nvmem-cells = <&macaddr_config_8>;
+ nvmem-cell-names = "mac-address";
+};
+
+&config {
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_config_8: macaddr at 8 {
+ reg = <0x8 0x6>;
+ };
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index a6427efe2b..78e2624fe7 100644
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -508,6 +508,10 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0 at eth0" "1:lan" "2:lan"
;;
+ tplink,deco-m4r-v1)
+ ucidef_add_switch "switch0" \
+ "0 at eth0" "3:lan:1" "5:lan:2"
+ ;;
hiwifi,hc6361|\
xiaomi,mi-router-4q|\
zbtlink,zbt-wd323)
diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 00aa34f0a8..668fd76af3 100644
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -269,6 +269,12 @@ case "$FIRMWARE" in
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9984/hw1.0/board.bin
;;
+ tplink,deco-m4r-v1)
+ caldata_extract "art" 0x5000 0x2f20
+ ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary config 0x8) -1)
+ ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
+ /lib/firmware/ath10k/QCA9888/hw2.0/board.bin
+ ;;
yuncore,a782|\
yuncore,xd4200)
caldata_extract "art" 0x5000 0x2f20
diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk
index ce0f81be6e..8f4bf90b83 100644
--- a/target/linux/ath79/image/generic-tp-link.mk
+++ b/target/linux/ath79/image/generic-tp-link.mk
@@ -459,6 +459,18 @@ define Device/tplink_eap245-v3
endef
TARGET_DEVICES += tplink_eap245-v3
+define Device/tplink_deco-m4r-v1
+ $(Device/tplink-safeloader-uimage)
+ SOC := qca9563
+ IMAGE_SIZE := 13824k
+ DEVICE_MODEL := Deco M4R
+ DEVICE_VARIANT := v1
+ DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
+ SUPPORTED_DEVICES += deco-m4r-v1
+ TPLINK_BOARD_ID := DECO-M4R-V1
+endef
+TARGET_DEVICES += tplink_deco-m4r-v1
+
define Device/tplink_re350k-v1
$(Device/tplink-safeloader)
SOC := qca9558
More information about the lede-commits
mailing list