[openwrt/openwrt] realtek: add ZyXEL GS1900-24HP v1 support
LEDE Commits
lede-commits at lists.infradead.org
Tue Apr 19 14:51:26 PDT 2022
hauke pushed a commit to openwrt/openwrt.git, branch openwrt-22.03:
https://git.openwrt.org/d60b3bf89010d750bb82c353d38086b40f3debf5
commit d60b3bf89010d750bb82c353d38086b40f3debf5
Author: Martin Kennedy <hurricos at gmail.com>
AuthorDate: Sat Mar 5 14:02:36 2022 -0500
realtek: add ZyXEL GS1900-24HP v1 support
The ZyXEL GS1900-24HP v1 is a 24 port PoE switch with two SFP ports,
similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24HP v1
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: Winbond W9751G8KB-25 64 MiB DDR2 SDRAM
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs:
* 1 PWR LED (green, not configurable)
* 1 SYS LED (green, configurable)
* 24 ethernet port link/activity LEDs (green, SoC controlled)
* 24 ethernet port PoE status LEDs
* 2 SFP status/activity LEDs (green, SoC controlled)
* Buttons:
* 1 "RESET" button on front panel (soft reset)
* 1 button ('SW1') behind right hex grate (hardwired power-off)
* PoE:
* Management MCU: ST Micro ST32F100 Microcontroller
* 6 BCM59111 PSE chips
* 170W power budget
* Power: 120-240V AC C13
* UART: Internal populated 10-pin header ('J5') providing RS232;
connected to SoC UART through a TI or SIPEX 3232C for voltage
level shifting.
* 'J5' RS232 Pinout (dot as pin 1):
2) SoC RXD
3) GND
10) SoC TXD
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot
the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24HP v1 is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only be installed in the first partition anyway (hardcoded in the
DTS). To ensure we are set to boot from the first partition, issue the
following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin
Signed-off-by: Martin Kennedy <hurricos at gmail.com>
[Add info on PoE hardware to commit message]
Signed-off-by: Sander Vanheule <sander at svanheule.net>
(cherry picked from commit a5ac8ad0ba9df50bdd0dda1dc26cf36f83006893)
---
package/boot/uboot-envtools/files/realtek | 1 +
.../realtek/base-files/etc/board.d/02_network | 1 +
.../dts-5.10/rtl8382_zyxel_gs1900-24hp-v1.dts | 125 +++++++++++++++++++++
target/linux/realtek/image/rtl838x.mk | 9 ++
4 files changed, 136 insertions(+)
diff --git a/package/boot/uboot-envtools/files/realtek b/package/boot/uboot-envtools/files/realtek
index 9836462a92..c07175a357 100644
--- a/package/boot/uboot-envtools/files/realtek
+++ b/package/boot/uboot-envtools/files/realtek
@@ -16,6 +16,7 @@ zyxel,gs1900-8hp-v1|\
zyxel,gs1900-8hp-v2|\
zyxel,gs1900-10hp|\
zyxel,gs1900-24-v1|\
+zyxel,gs1900-24hp-v1|\
zyxel,gs1900-24hp-v2)
idx="$(find_mtd_index u-boot-env)"
[ -n "$idx" ] && \
diff --git a/target/linux/realtek/base-files/etc/board.d/02_network b/target/linux/realtek/base-files/etc/board.d/02_network
index e8e3f6035d..af9db848dd 100644
--- a/target/linux/realtek/base-files/etc/board.d/02_network
+++ b/target/linux/realtek/base-files/etc/board.d/02_network
@@ -57,6 +57,7 @@ zyxel,gs1900-8hp-v1|\
zyxel,gs1900-8hp-v2)
ucidef_set_poe 70 "$lan_list"
;;
+zyxel,gs1900-24hp-v1|\
zyxel,gs1900-24hp-v2)
ucidef_set_poe 170 "$lan_list"
;;
diff --git a/target/linux/realtek/dts-5.10/rtl8382_zyxel_gs1900-24hp-v1.dts b/target/linux/realtek/dts-5.10/rtl8382_zyxel_gs1900-24hp-v1.dts
new file mode 100644
index 0000000000..7bb3410a31
--- /dev/null
+++ b/target/linux/realtek/dts-5.10/rtl8382_zyxel_gs1900-24hp-v1.dts
@@ -0,0 +1,125 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "rtl8380_zyxel_gs1900.dtsi"
+
+/ {
+ compatible = "zyxel,gs1900-24hp-v1", "realtek,rtl838x-soc";
+ model = "ZyXEL GS1900-24HP v1";
+
+ memory at 0 {
+ reg = <0x0 0x4000000>;
+ };
+
+ /* i2c of the left SFP cage: port 25 */
+ i2c0: i2c-gpio-0 {
+ compatible = "i2c-gpio";
+ sda-gpios = <&gpio1 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio1 25 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ sfp0: sfp-p25 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c0>;
+ los-gpio = <&gpio1 27 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpio = <&gpio1 26 GPIO_ACTIVE_LOW>;
+ tx-disable-gpio = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* i2c of the right SFP cage: port 26 */
+ i2c1: i2c-gpio-1 {
+ compatible = "i2c-gpio";
+ sda-gpios = <&gpio1 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio1 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ sfp1: sfp-p26 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c1>;
+ los-gpio = <&gpio1 33 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpio = <&gpio1 32 GPIO_ACTIVE_LOW>;
+ tx-disable-gpio = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&mdio {
+ EXTERNAL_PHY(0)
+ EXTERNAL_PHY(1)
+ EXTERNAL_PHY(2)
+ EXTERNAL_PHY(3)
+ EXTERNAL_PHY(4)
+ EXTERNAL_PHY(5)
+ EXTERNAL_PHY(6)
+ EXTERNAL_PHY(7)
+
+ EXTERNAL_PHY(16)
+ EXTERNAL_PHY(17)
+ EXTERNAL_PHY(18)
+ EXTERNAL_PHY(19)
+ EXTERNAL_PHY(20)
+ EXTERNAL_PHY(21)
+ EXTERNAL_PHY(22)
+ EXTERNAL_PHY(23)
+
+ INTERNAL_PHY(24)
+ INTERNAL_PHY(26)
+};
+
+&switch0 {
+ ports {
+ SWITCH_PORT(0, 1, qsgmii)
+ SWITCH_PORT(1, 2, qsgmii)
+ SWITCH_PORT(2, 3, qsgmii)
+ SWITCH_PORT(3, 4, qsgmii)
+ SWITCH_PORT(4, 5, qsgmii)
+ SWITCH_PORT(5, 6, qsgmii)
+ SWITCH_PORT(6, 7, qsgmii)
+ SWITCH_PORT(7, 8, qsgmii)
+
+ SWITCH_PORT(8, 9, internal)
+ SWITCH_PORT(9, 10, internal)
+ SWITCH_PORT(10, 11, internal)
+ SWITCH_PORT(11, 12, internal)
+ SWITCH_PORT(12, 13, internal)
+ SWITCH_PORT(13, 14, internal)
+ SWITCH_PORT(14, 15, internal)
+ SWITCH_PORT(15, 16, internal)
+
+ SWITCH_PORT(16, 17, qsgmii)
+ SWITCH_PORT(17, 18, qsgmii)
+ SWITCH_PORT(18, 19, qsgmii)
+ SWITCH_PORT(19, 20, qsgmii)
+ SWITCH_PORT(20, 21, qsgmii)
+ SWITCH_PORT(21, 22, qsgmii)
+ SWITCH_PORT(22, 23, qsgmii)
+ SWITCH_PORT(23, 24, qsgmii)
+
+ port at 24 {
+ reg = <24>;
+ label = "lan25";
+ phy-mode = "1000base-x";
+ managed = "in-band-status";
+ sfp = <&sfp0>;
+ };
+
+ port at 26 {
+ reg = <26>;
+ label = "lan26";
+ phy-mode = "1000base-x";
+ managed = "in-band-status";
+ sfp = <&sfp1>;
+ };
+ };
+};
+
diff --git a/target/linux/realtek/image/rtl838x.mk b/target/linux/realtek/image/rtl838x.mk
index 9688dd93de..29e7ff2695 100644
--- a/target/linux/realtek/image/rtl838x.mk
+++ b/target/linux/realtek/image/rtl838x.mk
@@ -145,6 +145,15 @@ define Device/zyxel_gs1900-24-v1
endef
TARGET_DEVICES += zyxel_gs1900-24-v1
+define Device/zyxel_gs1900-24hp-v1
+ $(Device/zyxel_gs1900)
+ SOC := rtl8382
+ DEVICE_MODEL := GS1900-24HP
+ DEVICE_VARIANT := v1
+ ZYXEL_VERS := AAHM
+endef
+TARGET_DEVICES += zyxel_gs1900-24hp-v1
+
define Device/zyxel_gs1900-24hp-v2
$(Device/zyxel_gs1900)
SOC := rtl8382
More information about the lede-commits
mailing list