[openwrt/openwrt] ath79: add support for MikroTik RouterBOARD 962UiGS-5HacT2HnT (hAP ac)
LEDE Commits
lede-commits at lists.infradead.org
Sat Apr 16 08:20:17 PDT 2022
hauke pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/c2140e32ce32b9cc60f7d408e20bdf45dce6a634
commit c2140e32ce32b9cc60f7d408e20bdf45dce6a634
Author: Ryan Mounce <ryan at mounce.com.au>
AuthorDate: Sat Apr 10 12:26:49 2021 +0930
ath79: add support for MikroTik RouterBOARD 962UiGS-5HacT2HnT (hAP ac)
This patch adds support for the MikroTik RouterBOARD 962UiGS-5HacT2HnT (hAP ac)
Specifications:
- SoC: QCA9558
- RAM: 128 MB
- Flash: 16 MB SPI
- 2.4GHz WLAN: 3x3:3 802.11n on SoC
- 5GHz WLAN: 3x3:3 802.11ac on QCA9880 connected via PCIe
- Switch: 5x 1000/100/10 on QCA8337 connected via RGMII
- SFP cage: connected via SGMII (tested with genuine & generic GLC-T)
- USB: 1x type A, GPIO power switch
- PoE: Passive input on Ether1, GPIO switched passthrough to Ether5
- Reset button
- "SFP" LED connected to SoC
- Ethernet LEDs connected to QCA8337 switch
- Green WLAN LED connected to QCA9880
Not working:
- Red WLAN LED
Installation:
TFTP boot initramfs image and then perform sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Ryan Mounce <ryan at mounce.com.au>
---
...9558_mikrotik_routerboard-962uigs-5hact2hnt.dts | 37 ++++
.../dts/qca9558_mikrotik_routerboard-96x.dtsi | 198 +++++++++++++++++++++
target/linux/ath79/image/mikrotik.mk | 11 ++
.../mikrotik/base-files/etc/board.d/02_network | 4 +
.../etc/hotplug.d/firmware/10-ath9k-eeprom | 3 +
.../etc/hotplug.d/firmware/11-ath10k-caldata | 1 +
6 files changed, 254 insertions(+)
diff --git a/target/linux/ath79/dts/qca9558_mikrotik_routerboard-962uigs-5hact2hnt.dts b/target/linux/ath79/dts/qca9558_mikrotik_routerboard-962uigs-5hact2hnt.dts
new file mode 100644
index 0000000000..f3fc31af14
--- /dev/null
+++ b/target/linux/ath79/dts/qca9558_mikrotik_routerboard-962uigs-5hact2hnt.dts
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca9558_mikrotik_routerboard-96x.dtsi"
+
+/ {
+ compatible = "mikrotik,routerboard-962uigs-5hact2hnt", "qca,qca9558";
+ model = "MikroTik RouterBOARD 962UiGS-5HacT2HnT (hAP ac)";
+
+ gpio-export {
+ compatible = "gpio-export";
+
+ port5_poe {
+ gpio-export,name = "port5-poe";
+ gpio-export,output = <1>;
+ gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&gpio {
+ input-poe-out-compat {
+ gpio-hog;
+ gpios = <2 GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "PoE out compat";
+ };
+};
+
+&wmac {
+ status = "okay";
+
+ qca,no-eeprom;
+};
+
+&pcie1 {
+ status = "okay";
+};
diff --git a/target/linux/ath79/dts/qca9558_mikrotik_routerboard-96x.dtsi b/target/linux/ath79/dts/qca9558_mikrotik_routerboard-96x.dtsi
new file mode 100644
index 0000000000..e1de96e40c
--- /dev/null
+++ b/target/linux/ath79/dts/qca9558_mikrotik_routerboard-96x.dtsi
@@ -0,0 +1,198 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca955x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ aliases {
+ led-boot = &led_user;
+ led-failsafe = &led_user;
+ led-upgrade = &led_user;
+ serial0 = &uart;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_user: user {
+ label = "green:user";
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+ };
+
+ gpio-export {
+ compatible = "gpio-export";
+
+ buzzer {
+ /* Beeper requires PWM for frequency selection */
+ gpio-export,name = "buzzer";
+ gpio-export,output = <0>;
+ gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
+ };
+
+ usb_power {
+ gpio-export,name = "usb-power";
+ gpio-export,output = <0>;
+ gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ i2c: i2c {
+ compatible = "i2c-gpio";
+
+ sda-gpios = <&gpio 18 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio 19 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <5>;
+ i2c-gpio,timeout-ms = <1>;
+ };
+
+ sfp1: sfp {
+ compatible = "sff,sfp";
+
+ i2c-bus = <&i2c>;
+ maximum-power-milliwatt = <1000>;
+ los-gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ tx-disable-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+ // Toggling GPIO16 actually enables/disables the transmitter,
+ // but the SFP driver does not seem to be using it.
+ };
+};
+
+&spi {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "RouterBoot";
+ reg = <0x0 0x20000>;
+ read-only;
+ compatible = "mikrotik,routerboot-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "bootloader1";
+ reg = <0x0 0x0>;
+ read-only;
+ };
+
+ hard_config {
+ read-only;
+ };
+
+ bios {
+ size = <0x1000>;
+ read-only;
+ };
+
+ partition at 10000 {
+ label = "bootloader2";
+ reg = <0x10000 0x0>;
+ read-only;
+ };
+
+ soft_config {
+ };
+ };
+
+ partition at 20000 {
+ compatible = "mikrotik,minor";
+ label = "firmware";
+ reg = <0x020000 0xfe0000>;
+ };
+ };
+ };
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy0: ethernet-phy at 0 {
+ reg = <0>;
+
+ qca,ar8327-initvals = <
+ /* PAD0_MODE from vendor firmware
+ * RGMII_EN, TX/RXCLK_DELAY_EN, TXCLK_DELAY_SEL=1
+ */
+ 0x04 0x07400000 /* PAD0_MODE */
+ 0x50 0xc737c737 /* LED_CTRL0 */
+ 0x54 0x00000000 /* LED_CTRL1 */
+ 0x58 0x00000000 /* LED_CTRL2 */
+ 0x5c 0x0030c300 /* LED_CTRL3 */
+ 0x7c 0x0000007e /* PORT0_STATUS */
+ >;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ phy-handle = <&phy0>;
+ /* gigabit pll-data from vendor firmware
+ * TX_INVERT, TX_DELAY=3, GIGE, OFFSET_PHASE
+ */
+ pll-data = <0x8f000000 0x00000101 0x00001616>;
+
+ gmac-config {
+ device = <&gmac>;
+ rgmii-enabled = <1>;
+ };
+};
+
+&mdio1 {
+ status = "okay";
+
+ phy_sfp: ethernet-phy at 0 {
+ reg = <0>;
+ phy-mode = "sgmii";
+ sfp = <&sfp1>;
+ };
+};
+
+ð1 {
+ status = "okay";
+
+ phy-handle = <&phy_sfp>;
+ pll-data = <0x03000000 0x00000101 0x00001616>;
+ qca955x-sgmii-fixup;
+
+ gmac-config {
+ device = <&gmac>;
+ };
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb_phy0 {
+ status = "okay";
+};
diff --git a/target/linux/ath79/image/mikrotik.mk b/target/linux/ath79/image/mikrotik.mk
index dccb05e45a..13aec3949a 100644
--- a/target/linux/ath79/image/mikrotik.mk
+++ b/target/linux/ath79/image/mikrotik.mk
@@ -38,6 +38,17 @@ define Device/mikrotik_routerboard-922uags-5hpacd
endef
TARGET_DEVICES += mikrotik_routerboard-922uags-5hpacd
+define Device/mikrotik_routerboard-962uigs-5hact2hnt
+ $(Device/mikrotik_nor)
+ SOC := qca9558
+ DEVICE_MODEL := RouterBOARD 962UiGS-5HacT2HnT (hAP ac)
+ DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct kmod-usb2 \
+ kmod-i2c-gpio kmod-sfp
+ IMAGE_SIZE := 16256k
+ SUPPORTED_DEVICES += rb-962uigs-5hact2hnt
+endef
+TARGET_DEVICES += mikrotik_routerboard-962uigs-5hact2hnt
+
define Device/mikrotik_routerboard-lhg-2nd
$(Device/mikrotik_nor)
SOC := qca9533
diff --git a/target/linux/ath79/mikrotik/base-files/etc/board.d/02_network b/target/linux/ath79/mikrotik/base-files/etc/board.d/02_network
index cc4121f93e..04bedfb569 100644
--- a/target/linux/ath79/mikrotik/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/mikrotik/base-files/etc/board.d/02_network
@@ -23,6 +23,10 @@ ath79_setup_interfaces()
mikrotik,routerboard-wapr-2nd)
ucidef_set_interface_lan "eth0"
;;
+ mikrotik,routerboard-962uigs-5hact2hnt)
+ ucidef_add_switch "switch0" \
+ "0 at eth0" "2:lan" "3:lan" "4:lan" "5:lan" "1:wan"
+ ;;
*)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
;;
diff --git a/target/linux/ath79/mikrotik/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/mikrotik/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index 8b1b5f04dd..4701460cb6 100644
--- a/target/linux/ath79/mikrotik/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ath79/mikrotik/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -34,6 +34,9 @@ case "$FIRMWARE" in
mikrotik,routerboard-wap-g-5hact2hnd)
caldata_mikrotik_ath9k 0x1000 0x440 $(macaddr_add "$mac_base" 2)
;;
+ mikrotik,routerboard-962uigs-5hact2hnt)
+ caldata_mikrotik_ath9k 0x1000 0x440 $(macaddr_add "$mac_base" 7)
+ ;;
*)
caldata_die "board $board is not supported yet"
;;
diff --git a/target/linux/ath79/mikrotik/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/mikrotik/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 31d4eeedbc..77cd47f6a0 100644
--- a/target/linux/ath79/mikrotik/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/mikrotik/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -12,6 +12,7 @@ case "$FIRMWARE" in
"ath10k/cal-pci-0000:00:00.0.bin")
case $board in
mikrotik,routerboard-921gs-5hpacd-15s|\
+ mikrotik,routerboard-962uigs-5hact2hnt|\
mikrotik,routerboard-wap-g-5hact2hnd)
caldata_sysfsload_from_file $wlan_data 0x5000 0x844
;;
More information about the lede-commits
mailing list