[openwrt/openwrt] realtek: backport gpio-realtek-otto driver from 5.13 to 5.10
LEDE Commits
lede-commits at lists.infradead.org
Sat Sep 25 15:37:26 PDT 2021
adrian pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/9bac1c20b8f39f2e0e342b087add5093b94feaed
commit 9bac1c20b8f39f2e0e342b087add5093b94feaed
Author: INAGAKI Hiroshi <musashino.open at gmail.com>
AuthorDate: Wed May 5 22:05:39 2021 +0900
realtek: backport gpio-realtek-otto driver from 5.13 to 5.10
This patch backports "gpio-realtek-otto" driver to Kernel 5.10.
"MACH_REALTEK_RTL" is used as a platform name in upstream, but "RTL838X"
is used in OpenWrt, so update the dependency by the additional patch.
Note: GPIO mapping is changed in the upstreamed driver.
old - new
24 - 0
25 - 1
26 - 2
27 - 3
28 - 4
29 - 5
30 - 6
31 - 7
16 - 8
17 - 9
18 - 10
19 - 11
20 - 12
21 - 13
22 - 14
23 - 15
8 - 16
9 - 17
10 - 18
11 - 19
12 - 20
13 - 21
14 - 22
15 - 23
Signed-off-by: INAGAKI Hiroshi <musashino.open at gmail.com>
---
target/linux/realtek/config-5.10 | 3 +
...ndings-gpio-binding-for-realtek-otto-gpio.patch | 109 ++++++
...2-5.13-gpio-add-realtek-otto-gpio-support.patch | 394 +++++++++++++++++++++
...update-dependencies-for-gpio-realtek-otto.patch | 13 +
4 files changed, 519 insertions(+)
diff --git a/target/linux/realtek/config-5.10 b/target/linux/realtek/config-5.10
index b9ed86b426..8baecf42f3 100644
--- a/target/linux/realtek/config-5.10
+++ b/target/linux/realtek/config-5.10
@@ -72,6 +72,9 @@ CONFIG_GENERIC_SCHED_CLOCK=y
CONFIG_GENERIC_SMP_IDLE_THREAD=y
CONFIG_GENERIC_TIME_VSYSCALL=y
CONFIG_GPIOLIB=y
+CONFIG_GPIOLIB_IRQCHIP=y
+CONFIG_GPIO_GENERIC=y
+CONFIG_GPIO_REALTEK_OTTO=y
CONFIG_GPIO_RTL8231=y
CONFIG_REALTEK_SOC_PHY=y
CONFIG_GRO_CELLS=y
diff --git a/target/linux/realtek/patches-5.10/001-5.13-dt-bindings-gpio-binding-for-realtek-otto-gpio.patch b/target/linux/realtek/patches-5.10/001-5.13-dt-bindings-gpio-binding-for-realtek-otto-gpio.patch
new file mode 100644
index 0000000000..111591c640
--- /dev/null
+++ b/target/linux/realtek/patches-5.10/001-5.13-dt-bindings-gpio-binding-for-realtek-otto-gpio.patch
@@ -0,0 +1,109 @@
+From a362c0ce64866939c3daa17c76943cfed555b065 Mon Sep 17 00:00:00 2001
+From: Sander Vanheule <sander at svanheule.net>
+Date: Tue, 30 Mar 2021 19:48:42 +0200
+Subject: dt-bindings: gpio: Binding for Realtek Otto GPIO
+
+Add a binding description for Realtek's GPIO controller found on several
+of their MIPS-based SoCs (codenamed Otto), such as the RTL838x and
+RTL839x series of switch SoCs.
+
+A fallback binding 'realtek,otto-gpio' is provided for cases where the
+actual port ordering is not known yet, and enabling the interrupt
+controller may result in uncaught interrupts.
+
+Signed-off-by: Sander Vanheule <sander at svanheule.net>
+Reviewed-by: Linus Walleij <linus.walleij at linaro.org>
+Reviewed-by: Rob Herring <robh at kernel.org>
+Signed-off-by: Bartosz Golaszewski <bgolaszewski at baylibre.com>
+---
+ .../bindings/gpio/realtek,otto-gpio.yaml | 78 ++++++++++++++++++++++
+ 1 file changed, 78 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/gpio/realtek,otto-gpio.yaml
+
+diff --git a/Documentation/devicetree/bindings/gpio/realtek,otto-gpio.yaml b/Documentation/devicetree/bindings/gpio/realtek,otto-gpio.yaml
+new file mode 100644
+index 0000000000000..100f20cebd76a
+--- /dev/null
++++ b/Documentation/devicetree/bindings/gpio/realtek,otto-gpio.yaml
+@@ -0,0 +1,78 @@
++# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
++%YAML 1.2
++---
++$id: http://devicetree.org/schemas/gpio/realtek,otto-gpio.yaml#
++$schema: http://devicetree.org/meta-schemas/core.yaml#
++
++title: Realtek Otto GPIO controller
++
++maintainers:
++ - Sander Vanheule <sander at svanheule.net>
++ - Bert Vermeulen <bert at biot.com>
++
++description: |
++ Realtek's GPIO controller on their MIPS switch SoCs (Otto platform) consists
++ of two banks of 32 GPIOs. These GPIOs can generate edge-triggered interrupts.
++ Each bank's interrupts are cascased into one interrupt line on the parent
++ interrupt controller, if provided.
++ This binding allows defining a single bank in the devicetree. The interrupt
++ controller is not supported on the fallback compatible name, which only
++ allows for GPIO port use.
++
++properties:
++ $nodename:
++ pattern: "^gpio@[0-9a-f]+$"
++
++ compatible:
++ items:
++ - enum:
++ - realtek,rtl8380-gpio
++ - realtek,rtl8390-gpio
++ - const: realtek,otto-gpio
++
++ reg:
++ maxItems: 1
++
++ "#gpio-cells":
++ const: 2
++
++ gpio-controller: true
++
++ ngpios:
++ minimum: 1
++ maximum: 32
++
++ interrupt-controller: true
++
++ "#interrupt-cells":
++ const: 2
++
++ interrupts:
++ maxItems: 1
++
++required:
++ - compatible
++ - reg
++ - "#gpio-cells"
++ - gpio-controller
++
++additionalProperties: false
++
++dependencies:
++ interrupt-controller: [ interrupts ]
++
++examples:
++ - |
++ gpio at 3500 {
++ compatible = "realtek,rtl8380-gpio", "realtek,otto-gpio";
++ reg = <0x3500 0x1c>;
++ gpio-controller;
++ #gpio-cells = <2>;
++ ngpios = <24>;
++ interrupt-controller;
++ #interrupt-cells = <2>;
++ interrupt-parent = <&rtlintc>;
++ interrupts = <23>;
++ };
++
++...
+--
+cgit 1.2.3-1.el7
+
diff --git a/target/linux/realtek/patches-5.10/002-5.13-gpio-add-realtek-otto-gpio-support.patch b/target/linux/realtek/patches-5.10/002-5.13-gpio-add-realtek-otto-gpio-support.patch
new file mode 100644
index 0000000000..fc13824282
--- /dev/null
+++ b/target/linux/realtek/patches-5.10/002-5.13-gpio-add-realtek-otto-gpio-support.patch
@@ -0,0 +1,394 @@
+From f0f7d662e8514169c90d3d84cd6df773b2983088 Mon Sep 17 00:00:00 2001
+From: Sander Vanheule <sander at svanheule.net>
+Date: Tue, 30 Mar 2021 19:48:43 +0200
+Subject: gpio: Add Realtek Otto GPIO support
+
+Realtek MIPS SoCs (platform name Otto) have GPIO controllers with up to
+64 GPIOs, divided over two banks. Each bank has a set of registers for
+32 GPIOs, with support for edge-triggered interrupts.
+
+Each GPIO bank consists of four 8-bit GPIO ports (ABCD and EFGH). Most
+registers pack one bit per GPIO, except for the IMR register, which
+packs two bits per GPIO (AB-CD).
+
+Although the byte order is currently assumed to have port A..D at offset
+0x0..0x3, this has been observed to be reversed on other, Lexra-based,
+SoCs (e.g. RTL8196E/97D/97F).
+
+Interrupt support is disabled for the fallback devicetree-compatible
+'realtek,otto-gpio'. This allows for quick support of GPIO banks in
+which the byte order would be unknown. In this case, the port ordering
+in the IMR registers may not match the reversed order in the other
+registers (DCBA, and BA-DC or DC-BA).
+
+Signed-off-by: Sander Vanheule <sander at svanheule.net>
+Reviewed-by: Linus Walleij <linus.walleij at linaro.org>
+Reviewed-by: Andy Shevchenko <andy.shevchenko at gmail.com>
+Signed-off-by: Bartosz Golaszewski <bgolaszewski at baylibre.com>
+---
+ drivers/gpio/Kconfig | 13 ++
+ drivers/gpio/Makefile | 1 +
+ drivers/gpio/gpio-realtek-otto.c | 325 +++++++++++++++++++++++++++++++++++++++
+ 3 files changed, 339 insertions(+)
+ create mode 100644 drivers/gpio/gpio-realtek-otto.c
+
+--- a/drivers/gpio/Kconfig
++++ b/drivers/gpio/Kconfig
+@@ -489,6 +489,19 @@ config GPIO_RDA
+ help
+ Say Y here to support RDA Micro GPIO controller.
+
++config GPIO_REALTEK_OTTO
++ tristate "Realtek Otto GPIO support"
++ depends on MACH_REALTEK_RTL
++ default MACH_REALTEK_RTL
++ select GPIO_GENERIC
++ select GPIOLIB_IRQCHIP
++ help
++ The GPIO controller on the Otto MIPS platform supports up to two
++ banks of 32 GPIOs, with edge triggered interrupts. The 32 GPIOs
++ are grouped in four 8-bit wide ports.
++
++ When built as a module, the module will be called realtek_otto_gpio.
++
+ config GPIO_REG
+ bool
+ help
+--- a/drivers/gpio/Makefile
++++ b/drivers/gpio/Makefile
+@@ -124,6 +124,7 @@ obj-$(CONFIG_GPIO_RC5T583) += gpio-rc5t
+ obj-$(CONFIG_GPIO_RCAR) += gpio-rcar.o
+ obj-$(CONFIG_GPIO_RDA) += gpio-rda.o
+ obj-$(CONFIG_GPIO_RDC321X) += gpio-rdc321x.o
++obj-$(CONFIG_GPIO_REALTEK_OTTO) += gpio-realtek-otto.o
+ obj-$(CONFIG_GPIO_REG) += gpio-reg.o
+ obj-$(CONFIG_ARCH_SA1100) += gpio-sa1100.o
+ obj-$(CONFIG_GPIO_SAMA5D2_PIOBU) += gpio-sama5d2-piobu.o
+--- /dev/null
++++ b/drivers/gpio/gpio-realtek-otto.c
+@@ -0,0 +1,325 @@
++// SPDX-License-Identifier: GPL-2.0-only
++
++#include <linux/gpio/driver.h>
++#include <linux/irq.h>
++#include <linux/minmax.h>
++#include <linux/mod_devicetable.h>
++#include <linux/module.h>
++#include <linux/platform_device.h>
++#include <linux/property.h>
++
++/*
++ * Total register block size is 0x1C for one bank of four ports (A, B, C, D).
++ * An optional second bank, with ports E, F, G, and H, may be present, starting
++ * at register offset 0x1C.
++ */
++
++/*
++ * Pin select: (0) "normal", (1) "dedicate peripheral"
++ * Not used on RTL8380/RTL8390, peripheral selection is managed by control bits
++ * in the peripheral registers.
++ */
++#define REALTEK_GPIO_REG_CNR 0x00
++/* Clear bit (0) for input, set bit (1) for output */
++#define REALTEK_GPIO_REG_DIR 0x08
++#define REALTEK_GPIO_REG_DATA 0x0C
++/* Read bit for IRQ status, write 1 to clear IRQ */
++#define REALTEK_GPIO_REG_ISR 0x10
++/* Two bits per GPIO in IMR registers */
++#define REALTEK_GPIO_REG_IMR 0x14
++#define REALTEK_GPIO_REG_IMR_AB 0x14
++#define REALTEK_GPIO_REG_IMR_CD 0x18
++#define REALTEK_GPIO_IMR_LINE_MASK GENMASK(1, 0)
++#define REALTEK_GPIO_IRQ_EDGE_FALLING 1
++#define REALTEK_GPIO_IRQ_EDGE_RISING 2
++#define REALTEK_GPIO_IRQ_EDGE_BOTH 3
++
++#define REALTEK_GPIO_MAX 32
++#define REALTEK_GPIO_PORTS_PER_BANK 4
++
++/**
++ * realtek_gpio_ctrl - Realtek Otto GPIO driver data
++ *
++ * @gc: Associated gpio_chip instance
++ * @base: Base address of the register block for a GPIO bank
++ * @lock: Lock for accessing the IRQ registers and values
++ * @intr_mask: Mask for interrupts lines
++ * @intr_type: Interrupt type selection
++ *
++ * Because the interrupt mask register (IMR) combines the function of IRQ type
++ * selection and masking, two extra values are stored. @intr_mask is used to
++ * mask/unmask the interrupts for a GPIO port, and @intr_type is used to store
++ * the selected interrupt types. The logical AND of these values is written to
++ * IMR on changes.
++ */
++struct realtek_gpio_ctrl {
++ struct gpio_chip gc;
++ void __iomem *base;
++ raw_spinlock_t lock;
++ u16 intr_mask[REALTEK_GPIO_PORTS_PER_BANK];
++ u16 intr_type[REALTEK_GPIO_PORTS_PER_BANK];
++};
++
++/* Expand with more flags as devices with other quirks are added */
++enum realtek_gpio_flags {
++ /*
++ * Allow disabling interrupts, for cases where the port order is
++ * unknown. This may result in a port mismatch between ISR and IMR.
++ * An interrupt would appear to come from a different line than the
++ * line the IRQ handler was assigned to, causing uncaught interrupts.
++ */
++ GPIO_INTERRUPTS_DISABLED = BIT(0),
++};
++
++static struct realtek_gpio_ctrl *irq_data_to_ctrl(struct irq_data *data)
++{
++ struct gpio_chip *gc = irq_data_get_irq_chip_data(data);
++
++ return container_of(gc, struct realtek_gpio_ctrl, gc);
++}
++
++/*
++ * Normal port order register access
++ *
++ * Port information is stored with the first port at offset 0, followed by the
++ * second, etc. Most registers store one bit per GPIO and use a u8 value per
++ * port. The two interrupt mask registers store two bits per GPIO, so use u16
++ * values.
++ */
++static void realtek_gpio_write_imr(struct realtek_gpio_ctrl *ctrl,
++ unsigned int port, u16 irq_type, u16 irq_mask)
++{
++ iowrite16(irq_type & irq_mask, ctrl->base + REALTEK_GPIO_REG_IMR + 2 * port);
++}
++
++static void realtek_gpio_clear_isr(struct realtek_gpio_ctrl *ctrl,
++ unsigned int port, u8 mask)
++{
++ iowrite8(mask, ctrl->base + REALTEK_GPIO_REG_ISR + port);
++}
++
++static u8 realtek_gpio_read_isr(struct realtek_gpio_ctrl *ctrl, unsigned int port)
++{
++ return ioread8(ctrl->base + REALTEK_GPIO_REG_ISR + port);
++}
++
++/* Set the rising and falling edge mask bits for a GPIO port pin */
++static u16 realtek_gpio_imr_bits(unsigned int pin, u16 value)
++{
++ return (value & REALTEK_GPIO_IMR_LINE_MASK) << 2 * pin;
++}
++
++static void realtek_gpio_irq_ack(struct irq_data *data)
++{
++ struct realtek_gpio_ctrl *ctrl = irq_data_to_ctrl(data);
++ irq_hw_number_t line = irqd_to_hwirq(data);
++ unsigned int port = line / 8;
++ unsigned int port_pin = line % 8;
++
++ realtek_gpio_clear_isr(ctrl, port, BIT(port_pin));
++}
++
++static void realtek_gpio_irq_unmask(struct irq_data *data)
++{
++ struct realtek_gpio_ctrl *ctrl = irq_data_to_ctrl(data);
++ unsigned int line = irqd_to_hwirq(data);
++ unsigned int port = line / 8;
++ unsigned int port_pin = line % 8;
++ unsigned long flags;
++ u16 m;
++
++ raw_spin_lock_irqsave(&ctrl->lock, flags);
++ m = ctrl->intr_mask[port];
++ m |= realtek_gpio_imr_bits(port_pin, REALTEK_GPIO_IMR_LINE_MASK);
++ ctrl->intr_mask[port] = m;
++ realtek_gpio_write_imr(ctrl, port, ctrl->intr_type[port], m);
++ raw_spin_unlock_irqrestore(&ctrl->lock, flags);
++}
++
++static void realtek_gpio_irq_mask(struct irq_data *data)
++{
++ struct realtek_gpio_ctrl *ctrl = irq_data_to_ctrl(data);
++ unsigned int line = irqd_to_hwirq(data);
++ unsigned int port = line / 8;
++ unsigned int port_pin = line % 8;
++ unsigned long flags;
++ u16 m;
++
++ raw_spin_lock_irqsave(&ctrl->lock, flags);
++ m = ctrl->intr_mask[port];
++ m &= ~realtek_gpio_imr_bits(port_pin, REALTEK_GPIO_IMR_LINE_MASK);
++ ctrl->intr_mask[port] = m;
++ realtek_gpio_write_imr(ctrl, port, ctrl->intr_type[port], m);
++ raw_spin_unlock_irqrestore(&ctrl->lock, flags);
++}
++
++static int realtek_gpio_irq_set_type(struct irq_data *data, unsigned int flow_type)
++{
++ struct realtek_gpio_ctrl *ctrl = irq_data_to_ctrl(data);
++ unsigned int line = irqd_to_hwirq(data);
++ unsigned int port = line / 8;
++ unsigned int port_pin = line % 8;
++ unsigned long flags;
++ u16 type, t;
++
++ switch (flow_type & IRQ_TYPE_SENSE_MASK) {
++ case IRQ_TYPE_EDGE_FALLING:
++ type = REALTEK_GPIO_IRQ_EDGE_FALLING;
++ break;
++ case IRQ_TYPE_EDGE_RISING:
++ type = REALTEK_GPIO_IRQ_EDGE_RISING;
++ break;
++ case IRQ_TYPE_EDGE_BOTH:
++ type = REALTEK_GPIO_IRQ_EDGE_BOTH;
++ break;
++ default:
++ return -EINVAL;
++ }
++
++ irq_set_handler_locked(data, handle_edge_irq);
++
++ raw_spin_lock_irqsave(&ctrl->lock, flags);
++ t = ctrl->intr_type[port];
++ t &= ~realtek_gpio_imr_bits(port_pin, REALTEK_GPIO_IMR_LINE_MASK);
++ t |= realtek_gpio_imr_bits(port_pin, type);
++ ctrl->intr_type[port] = t;
++ realtek_gpio_write_imr(ctrl, port, t, ctrl->intr_mask[port]);
++ raw_spin_unlock_irqrestore(&ctrl->lock, flags);
++
++ return 0;
++}
++
++static void realtek_gpio_irq_handler(struct irq_desc *desc)
++{
++ struct gpio_chip *gc = irq_desc_get_handler_data(desc);
++ struct realtek_gpio_ctrl *ctrl = gpiochip_get_data(gc);
++ struct irq_chip *irq_chip = irq_desc_get_chip(desc);
++ unsigned int lines_done;
++ unsigned int port_pin_count;
++ unsigned int irq;
++ unsigned long status;
++ int offset;
++
++ chained_irq_enter(irq_chip, desc);
++
++ for (lines_done = 0; lines_done < gc->ngpio; lines_done += 8) {
++ status = realtek_gpio_read_isr(ctrl, lines_done / 8);
++ port_pin_count = min(gc->ngpio - lines_done, 8U);
++ for_each_set_bit(offset, &status, port_pin_count) {
++ irq = irq_find_mapping(gc->irq.domain, offset);
++ generic_handle_irq(irq);
++ }
++ }
++
++ chained_irq_exit(irq_chip, desc);
++}
++
++static int realtek_gpio_irq_init(struct gpio_chip *gc)
++{
++ struct realtek_gpio_ctrl *ctrl = gpiochip_get_data(gc);
++ unsigned int port;
++
++ for (port = 0; (port * 8) < gc->ngpio; port++) {
++ realtek_gpio_write_imr(ctrl, port, 0, 0);
++ realtek_gpio_clear_isr(ctrl, port, GENMASK(7, 0));
++ }
++
++ return 0;
++}
++
++static struct irq_chip realtek_gpio_irq_chip = {
++ .name = "realtek-otto-gpio",
++ .irq_ack = realtek_gpio_irq_ack,
++ .irq_mask = realtek_gpio_irq_mask,
++ .irq_unmask = realtek_gpio_irq_unmask,
++ .irq_set_type = realtek_gpio_irq_set_type,
++};
++
++static const struct of_device_id realtek_gpio_of_match[] = {
++ {
++ .compatible = "realtek,otto-gpio",
++ .data = (void *)GPIO_INTERRUPTS_DISABLED,
++ },
++ {
++ .compatible = "realtek,rtl8380-gpio",
++ },
++ {
++ .compatible = "realtek,rtl8390-gpio",
++ },
++ {}
++};
++MODULE_DEVICE_TABLE(of, realtek_gpio_of_match);
++
++static int realtek_gpio_probe(struct platform_device *pdev)
++{
++ struct device *dev = &pdev->dev;
++ unsigned int dev_flags;
++ struct gpio_irq_chip *girq;
++ struct realtek_gpio_ctrl *ctrl;
++ u32 ngpios;
++ int err, irq;
++
++ ctrl = devm_kzalloc(dev, sizeof(*ctrl), GFP_KERNEL);
++ if (!ctrl)
++ return -ENOMEM;
++
++ dev_flags = (unsigned int) device_get_match_data(dev);
++
++ ngpios = REALTEK_GPIO_MAX;
++ device_property_read_u32(dev, "ngpios", &ngpios);
++
++ if (ngpios > REALTEK_GPIO_MAX) {
++ dev_err(&pdev->dev, "invalid ngpios (max. %d)\n",
++ REALTEK_GPIO_MAX);
++ return -EINVAL;
++ }
++
++ ctrl->base = devm_platform_ioremap_resource(pdev, 0);
++ if (IS_ERR(ctrl->base))
++ return PTR_ERR(ctrl->base);
++
++ raw_spin_lock_init(&ctrl->lock);
++
++ err = bgpio_init(&ctrl->gc, dev, 4,
++ ctrl->base + REALTEK_GPIO_REG_DATA, NULL, NULL,
++ ctrl->base + REALTEK_GPIO_REG_DIR, NULL,
++ BGPIOF_BIG_ENDIAN_BYTE_ORDER);
++ if (err) {
++ dev_err(dev, "unable to init generic GPIO");
++ return err;
++ }
++
++ ctrl->gc.ngpio = ngpios;
++ ctrl->gc.owner = THIS_MODULE;
++
++ irq = platform_get_irq_optional(pdev, 0);
++ if (!(dev_flags & GPIO_INTERRUPTS_DISABLED) && irq > 0) {
++ girq = &ctrl->gc.irq;
++ girq->chip = &realtek_gpio_irq_chip;
++ girq->default_type = IRQ_TYPE_NONE;
++ girq->handler = handle_bad_irq;
++ girq->parent_handler = realtek_gpio_irq_handler;
++ girq->num_parents = 1;
++ girq->parents = devm_kcalloc(dev, girq->num_parents,
++ sizeof(*girq->parents), GFP_KERNEL);
++ if (!girq->parents)
++ return -ENOMEM;
++ girq->parents[0] = irq;
++ girq->init_hw = realtek_gpio_irq_init;
++ }
++
++ return devm_gpiochip_add_data(dev, &ctrl->gc, ctrl);
++}
++
++static struct platform_driver realtek_gpio_driver = {
++ .driver = {
++ .name = "realtek-otto-gpio",
++ .of_match_table = realtek_gpio_of_match,
++ },
++ .probe = realtek_gpio_probe,
++};
++module_platform_driver(realtek_gpio_driver);
++
++MODULE_DESCRIPTION("Realtek Otto GPIO support");
++MODULE_AUTHOR("Sander Vanheule <sander at svanheule.net>");
++MODULE_LICENSE("GPL v2");
diff --git a/target/linux/realtek/patches-5.10/303-gpio-update-dependencies-for-gpio-realtek-otto.patch b/target/linux/realtek/patches-5.10/303-gpio-update-dependencies-for-gpio-realtek-otto.patch
new file mode 100644
index 0000000000..4ff98e44e8
--- /dev/null
+++ b/target/linux/realtek/patches-5.10/303-gpio-update-dependencies-for-gpio-realtek-otto.patch
@@ -0,0 +1,13 @@
+--- a/drivers/gpio/Kconfig
++++ b/drivers/gpio/Kconfig
+@@ -491,8 +491,8 @@ config GPIO_RDA
+
+ config GPIO_REALTEK_OTTO
+ tristate "Realtek Otto GPIO support"
+- depends on MACH_REALTEK_RTL
+- default MACH_REALTEK_RTL
++ depends on RTL838X
++ default RTL838X
+ select GPIO_GENERIC
+ select GPIOLIB_IRQCHIP
+ help
More information about the lede-commits
mailing list