[openwrt/openwrt] ath79: add support for TP-Link CPE710-v1
LEDE Commits
lede-commits at lists.infradead.org
Sat Sep 25 10:29:28 PDT 2021
adrian pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/ac03e246351fbfa98e98f0319cce3a8663f836d3
commit ac03e246351fbfa98e98f0319cce3a8663f836d3
Author: Andrew Cameron <apcameron at softhome.net>
AuthorDate: Mon Apr 12 13:24:33 2021 -0500
ath79: add support for TP-Link CPE710-v1
TP-Link CPE710-v1 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on the AP152 reference board
Specifications:
- SoC: QCA9563-AL3A MIPS 74kc @ 775MHz, AHB @ 258MHz
- RAM: 128MiB DDR2 @ 650MHz
- Flash: 16MiB SPI NOR Based on the GD25Q128
- Wi-Fi 5Ghz: ath10k chip (802.11ac for up to 867Mbps on 5GHz wireless
data rate) Based on the QCA9896
- Ethernet: one 1GbE port
- 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal
reflector
- Power, LAN, WLAN5G Blue LEDs
- 3x Blue LEDs
Flashing instructions:
Flash factory image through stock firmware WEB UI or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 30-40 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron at softhome.net>
[convert to nvmem, fix MAC assignment in 11-ath10k-caldata]
Signed-off-by: Adrian Schmutzler <freifunk at adrianschmutzler.de>
---
.../linux/ath79/dts/qca9563_tplink_cpe710-v1.dts | 152 +++++++++++++++++++++
.../ath79/generic/base-files/etc/board.d/01_leds | 3 +-
.../generic/base-files/etc/board.d/02_network | 1 +
.../etc/hotplug.d/firmware/11-ath10k-caldata | 6 +
target/linux/ath79/image/generic-tp-link.mk | 11 ++
tools/firmware-utils/src/tplink-safeloader.c | 37 +++++
6 files changed, 209 insertions(+), 1 deletion(-)
diff --git a/target/linux/ath79/dts/qca9563_tplink_cpe710-v1.dts b/target/linux/ath79/dts/qca9563_tplink_cpe710-v1.dts
new file mode 100644
index 0000000000..c97d1652cb
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_tplink_cpe710-v1.dts
@@ -0,0 +1,152 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca956x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "TP-Link CPE710 v1";
+ compatible = "tplink,cpe710-v1", "qca,qca9563";
+
+ aliases {
+ label-mac-device = ð0;
+ led-boot = &led_lan;
+ led-failsafe = &led_lan;
+ led-upgrade = &led_lan;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_lan: lan {
+ label = "blue:lan";
+ gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan5g {
+ label = "blue:wlan5g";
+ gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "Reset button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&spi {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x000000 0x040000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "u-boot-env";
+ reg = <0x040000 0x010000>;
+ };
+
+ partition at 50000 {
+ label = "partition-table";
+ reg = <0x050000 0x010000>;
+ read-only;
+ };
+
+ info: partition at 60000 {
+ label = "info";
+ reg = <0x060000 0x010000>;
+ read-only;
+ };
+
+ partition at 70000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x070000 0xf50000>;
+ };
+
+ partition at fc0000 {
+ label = "config";
+ reg = <0xfc0000 0x030000>;
+ read-only;
+ };
+
+ art: partition at ff0000 {
+ label = "art";
+ reg = <0xff0000 0x010000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&pinmux {
+ mdio_pins: mdio_pins {
+ /* GPIO 10 as MDIO(0x20), GPIO 8 as MDC(0x21) */
+ pinctrl-single,bits = <0x8 0x00200021 0x00ff00ff>;
+ };
+};
+
+&mdio0 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio_pins>;
+
+ phy-mask = <0x10>;
+
+ phy4: ethernet-phy at 4 {
+ reg = <4>;
+ reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ phy-handle = <&phy4>;
+ phy-mode = "sgmii";
+
+ nvmem-cells = <&macaddr_info_8>;
+ nvmem-cell-names = "mac-address";
+
+ qca956x-serdes-fixup;
+
+ gmac-config {
+ device = <&gmac>;
+ };
+};
+
+&info {
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_info_8: macaddr at 8 {
+ reg = <0x8 0x6>;
+ };
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index ffc6f3086e..1c112b4952 100644
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -169,7 +169,8 @@ enterasys,ws-ap3705i|\
openmesh,mr900-v1|\
openmesh,mr900-v2|\
openmesh,mr1750-v1|\
-openmesh,mr1750-v2)
+openmesh,mr1750-v2|\
+tplink,cpe710-v1)
ucidef_set_led_netdev "lan" "LAN" "blue:lan" "eth0"
;;
compex,wpj344-16m|\
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index e2c6f9feac..af4cf08ce0 100644
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -63,6 +63,7 @@ ath79_setup_interfaces()
tplink,cpe510-v3|\
tplink,cpe610-v1|\
tplink,cpe610-v2|\
+ tplink,cpe710-v1|\
tplink,eap225-outdoor-v1|\
tplink,eap225-v3|\
tplink,eap245-v1|\
diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 5ba1a7a8ff..7f8c1b1143 100644
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -236,6 +236,12 @@ case "$FIRMWARE" in
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
;;
+ tplink,cpe710-v1)
+ caldata_extract "art" 0x5000 0x2f20
+ ath10k_patch_mac $(mtd_get_mac_binary info 0x8)
+ ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
+ /lib/firmware/ath10k/QCA9888/hw2.0/board.bin
+ ;;
tplink,eap225-outdoor-v1|\
tplink,eap225-v3|\
tplink,eap225-wall-v2|\
diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk
index b6755fe547..363be289c6 100644
--- a/target/linux/ath79/image/generic-tp-link.mk
+++ b/target/linux/ath79/image/generic-tp-link.mk
@@ -362,6 +362,17 @@ define Device/tplink_cpe610-v2
endef
TARGET_DEVICES += tplink_cpe610-v2
+define Device/tplink_cpe710-v1
+ $(Device/tplink-safeloader-uimage)
+ SOC := qca9563
+ IMAGE_SIZE := 15680k
+ DEVICE_MODEL := CPE710
+ DEVICE_VARIANT := v1
+ DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
+ TPLINK_BOARD_ID := CPE710V1
+endef
+TARGET_DEVICES += tplink_cpe710-v1
+
define Device/tplink-eap2x5
$(Device/tplink-safeloader)
LOADER_TYPE := elf
diff --git a/tools/firmware-utils/src/tplink-safeloader.c b/tools/firmware-utils/src/tplink-safeloader.c
index b20d1fdd30..03329a3926 100644
--- a/tools/firmware-utils/src/tplink-safeloader.c
+++ b/tools/firmware-utils/src/tplink-safeloader.c
@@ -534,6 +534,43 @@ static struct device_info boards[] = {
.first_sysupgrade_partition = "os-image",
.last_sysupgrade_partition = "support-list",
},
+ /** Firmware layout for the CPE710 V1 */
+ {
+ .id = "CPE710V1",
+ .vendor = "CPE710(TP-LINK|UN|AC866-5|00000000):1.0\r\n",
+ .support_list =
+ "SupportList:\r\n"
+ "CPE710(TP-LINK|UN|AC866-5|00000000):1.0\r\n"
+ "CPE710(TP-LINK|EU|AC866-5|45550000):1.0\r\n"
+ "CPE710(TP-LINK|US|AC866-5|55530000):1.0\r\n"
+ "CPE710(TP-LINK|UN|AC866-5):1.0\r\n"
+ "CPE710(TP-LINK|EU|AC866-5):1.0\r\n"
+ "CPE710(TP-LINK|US|AC866-5):1.0\r\n",
+ .part_trail = 0xff,
+ .soft_ver = SOFT_VER_DEFAULT,
+
+ .partitions = {
+ {"fs-uboot", 0x00000, 0x50000},
+ {"partition-table", 0x50000, 0x02000},
+ {"default-mac", 0x60000, 0x00020},
+ {"serial-number", 0x60100, 0x00020},
+ {"product-info", 0x61100, 0x00100},
+ {"device-info", 0x61400, 0x00400},
+ {"signature", 0x62000, 0x00400},
+ {"device-id", 0x63000, 0x00100},
+ {"firmware", 0x70000, 0xf40000},
+ {"soft-version", 0xfb0000, 0x00100},
+ {"support-list", 0xfb1000, 0x01000},
+ {"user-config", 0xfc0000, 0x10000},
+ {"default-config", 0xfd0000, 0x10000},
+ {"log", 0xfe0000, 0x10000},
+ {"radio", 0xff0000, 0x10000},
+ {NULL, 0, 0}
+ },
+
+ .first_sysupgrade_partition = "os-image",
+ .last_sysupgrade_partition = "support-list",
+ },
{
.id = "WBS210",
More information about the lede-commits
mailing list