[openwrt/openwrt] realtek: add support for INABA Abaniact AML2-17GP
LEDE Commits
lede-commits at lists.infradead.org
Fri May 7 06:05:44 BST 2021
ynezz pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/4c0c860846b1ad0ba586f847f38dd9bb43aef4b9
commit 4c0c860846b1ad0ba586f847f38dd9bb43aef4b9
Author: INAGAKI Hiroshi <musashino.open at gmail.com>
AuthorDate: Wed Sep 16 14:11:05 2020 +0900
realtek: add support for INABA Abaniact AML2-17GP
INABA Abaniact AML2-17GP is a 17 port gigabit switch, based on RTL8382.
Specification:
- SoC : Realtek RTL8382
- RAM : DDR3 128 MiB (SK hynix H5TQ1G63EFR)
- Flash : SPI-NOR 32 MiB (Macronix MX25L25635FZ2I-10G)
- Ethernet : 10/100/1000 Mbps x17
- port 1-8 : RTL8218B (SoC)
- port 8-16 : RTL8218D
- port wan : RTL8214FC
- LEDs/Keys : 1x, 1x
- UART : pin header on PCB (Molex 530470410 compatible)
- J14: 3.3V, GND, RX, TX from rear side
- 115200n8
- Power : 100-240 VAC, 50/60 Hz, 0.21 A
- Plug : IEC 60320-C13
Flash instruction using initramfs image:
1. Boot AML2-17GP normally
2. Set the IP address of computer to the range of 192.168.1.0/24, other
than 192.168.1.248 and connect computer to "WAN/CONSOLE" port of
AML2-17GP
3. Access to "http://192.168.1.248" and open firmware setting page
-- UI Language: 日本語 --
"メンテナンス" -> "デュアルイメージ"
-- UI Language: ENGLISH --
"Maintenance" -> "Dual Image"
4. Check "イメージ情報 (en: "Images Information")" and set the first
image to active by choosing "アクティブイメージ" (en: "Active
Image") in the partition "0"
5. open firmware upgrade page
-- UI Language: 日本語 --
"メンテナンス" -> "アップグレードマネージャー"
-- UI Language: ENGLISH --
"Maintenance" -> "Upgrade Manager"
6. Set the properties as follows
-- UI Language: 日本語 --
"アップグレード方式" : "HTTP"
"アップグレードタイプ" : "イメージ"
"イメージ" : "アクティブ"
"ブラウズファイル" : (select the OpenWrt initramfs image)
-- UI Language: ENGLISH --
"Upgrade Method" : "HTTP"
"Upgrade Type" : "Image"
"Image" : "(Active)"
"Browse file" : (select the OpenWrt initramfs image)
7. Press "アップグレード" (en: "Upgrade") button and perform upgrade
8. Wait ~150 seconds to complete flashing
9. After the flashing, the following message is showed and press "OK"
button to reboot
-- UI Language: 日本語 --
"成功!! 今すぐリブートしますか?"
-- UI Language: ENGLISH --
"Success!! Do you want to reboot now?"
10. After the rebooting, reconnect the cable to other port (1-16) and
open the SSH connection, download the sysupgrade image to the device
and perform sysupgrade with it
11. Wait ~120 seconds to complete sysupgrade
Note:
- The uploaded image via WebUI will only be written with the length
embedded in the uImage header. If the sysupgrade image is specified,
only the kernel is flashed and lacks the rootfs, this causes a kernel
panic while booting and bootloops.
To avoid this issue, initramfs image is required for flashing on WebUI
of stock firmware.
- This device has 1x LED named as "POWER", but it's not connected to the
GPIO of SoC and cannot be controlled.
- port 17 is named as "WAN/CONSOLE". This port is for the upstream
connection and console access (telnet/WebUI) on stock firmware.
Back to stock firmware:
1. Set "bootpartition" variable in u-boot-env2 partition to "1" by
fw_setsys
fw_setsys bootpartition 1
2. Reboot AML2-17GP
Signed-off-by: INAGAKI Hiroshi <musashino.open at gmail.com>
---
.../linux/realtek/dts/rtl8382_inaba_aml2-17gp.dts | 164 +++++++++++++++++++++
target/linux/realtek/image/Makefile | 9 ++
2 files changed, 173 insertions(+)
diff --git a/target/linux/realtek/dts/rtl8382_inaba_aml2-17gp.dts b/target/linux/realtek/dts/rtl8382_inaba_aml2-17gp.dts
new file mode 100644
index 0000000000..87761ac462
--- /dev/null
+++ b/target/linux/realtek/dts/rtl8382_inaba_aml2-17gp.dts
@@ -0,0 +1,164 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "rtl838x.dtsi"
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ compatible = "inaba,aml2-17gp", "realtek,rtl838x-soc";
+ model = "INABA Abaniact AML2-17GP";
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ };
+
+ memory at 0 {
+ device_type = "memory";
+ reg = <0x0 0x8000000>;
+ };
+
+ keys {
+ compatible = "gpio-keys-polled";
+ poll-interval = <20>;
+
+ reset {
+ label = "reset";
+ gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+};
+
+&gpio0 {
+ indirect-access-bus-id = <0>;
+};
+
+&spi0 {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x80000>;
+ read-only;
+ };
+
+ partition at 80000 {
+ label = "u-boot-env";
+ reg = <0x80000 0x10000>;
+ read-only;
+ };
+
+ partition at 90000 {
+ label = "u-boot-env2";
+ reg = <0x90000 0x10000>;
+ };
+
+ partition at a0000 {
+ label = "jffs2_cfg";
+ reg = <0xa0000 0x400000>;
+ read-only;
+ };
+
+ partition at 4a0000 {
+ label = "jffs2_log";
+ reg = <0x4a0000 0x100000>;
+ read-only;
+ };
+
+ partition at 5a0000 {
+ compatible = "openwrt,uimage", "denx,uimage";
+ label = "firmware";
+ reg = <0x5a0000 0xd30000>;
+ openwrt,ih-magic = <0x83800000>;
+ };
+
+ partition at 12d0000 {
+ label = "runtime2";
+ reg = <0x12d0000 0xd30000>;
+ };
+ };
+ };
+};
+
+ðernet0 {
+ mdio-bus {
+ compatible = "realtek,rtl838x-mdio";
+ regmap = <ðernet0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ INTERNAL_PHY(8)
+ INTERNAL_PHY(9)
+ INTERNAL_PHY(10)
+ INTERNAL_PHY(11)
+ INTERNAL_PHY(12)
+ INTERNAL_PHY(13)
+ INTERNAL_PHY(14)
+ INTERNAL_PHY(15)
+
+ EXTERNAL_PHY(16)
+ EXTERNAL_PHY(17)
+ EXTERNAL_PHY(18)
+ EXTERNAL_PHY(19)
+ EXTERNAL_PHY(20)
+ EXTERNAL_PHY(21)
+ EXTERNAL_PHY(22)
+ EXTERNAL_PHY(23)
+
+ EXTERNAL_PHY(24)
+ };
+};
+
+&switch0 {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ SWITCH_PORT(8, 1, internal)
+ SWITCH_PORT(9, 2, internal)
+ SWITCH_PORT(10, 3, internal)
+ SWITCH_PORT(11, 4, internal)
+ SWITCH_PORT(12, 5, internal)
+ SWITCH_PORT(13, 6, internal)
+ SWITCH_PORT(14, 7, internal)
+ SWITCH_PORT(15, 8, internal)
+
+ SWITCH_PORT(16, 9, qsgmii)
+ SWITCH_PORT(17, 10, qsgmii)
+ SWITCH_PORT(18, 11, qsgmii)
+ SWITCH_PORT(19, 12, qsgmii)
+ SWITCH_PORT(20, 13, qsgmii)
+ SWITCH_PORT(21, 14, qsgmii)
+ SWITCH_PORT(22, 15, qsgmii)
+ SWITCH_PORT(23, 16, qsgmii)
+
+ port at 24 {
+ reg = <24>;
+ label = "wan";
+ phy-handle = <&phy24>;
+ phy-mode = "qsgmii";
+ };
+
+ port at 28 {
+ ethernet = <ðernet0>;
+ reg = <28>;
+ phy-mode = "internal";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+};
diff --git a/target/linux/realtek/image/Makefile b/target/linux/realtek/image/Makefile
index b889cf84d8..ebc0c0a784 100644
--- a/target/linux/realtek/image/Makefile
+++ b/target/linux/realtek/image/Makefile
@@ -72,6 +72,15 @@ define Device/d-link_dgs-1210-28
endef
TARGET_DEVICES += d-link_dgs-1210-28
+define Device/inaba_aml2-17gp
+ SOC := rtl8382
+ IMAGE_SIZE := 13504k
+ DEVICE_VENDOR := INABA
+ DEVICE_MODEL := Abaniact AML2-17GP
+ UIMAGE_MAGIC := 0x83800000
+endef
+TARGET_DEVICES += inaba_aml2-17gp
+
define Device/netgear_gs108t-v3
$(Device/netgear_nge)
DEVICE_MODEL := GS108T
More information about the lede-commits
mailing list