[openwrt/openwrt] mediatek: add support for Ubiquiti UniFi 6 LR
LEDE Commits
lede-commits at lists.infradead.org
Thu Feb 18 06:14:43 EST 2021
blocktrron pushed a commit to openwrt/openwrt.git, branch openwrt-21.02:
https://git.openwrt.org/194e85e7dbc458891be2712f1055970ea9135826
commit 194e85e7dbc458891be2712f1055970ea9135826
Author: David Bauer <mail at david-bauer.net>
AuthorDate: Thu Feb 11 17:09:06 2021 +0100
mediatek: add support for Ubiquiti UniFi 6 LR
Hardware
--------
MediaTek MT7622
512MB DDR3 RAM
64M SPI-NOR Flash (Winbond W25Q512JV)
MediaTek MT7622 802.11bgn 4T4R WMAC
MediaTek MT7915 802.11ax 4T4R
Marvell AQR1112 100/1000/2500 NBase-T PHY
Holtek HT32F52241 LED controller
Reset Switch
UART
----
CPU UART0 at the pinout next to the Holtek MCU.
Pinout (first pin next to SoC / MCU)
0 3V3
1 RX
2 TX
3 GND
Settings are 115200 8N1.
Opening the case
----------------
Opening the case is not a nice task, as itis glued together. Insert a
flat knife between the front and back casing below the ethernet port.
Open up a gap this way and insert a flat scredriver, remove the knife.
Work your way around the casing by applying force to seperate the front
and back casing. This losens the glue and opens the plastic clips. Be
gentle, as these clips are very cheap and break quickly.
Installation
------------
1. Connect to the booted device at 192.168.1.20 using username/password
"ubnt".
2. Transfer the OpenWrt sysupgrade image to the device using SCP.
3. Check the mtd partition number for bs / kernel0 / kernel1
$ cat /proc/mtd
4. Set the bootselect flag to boot from kernel0
$ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6
5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1
$ dd if=openwrt.bin of=/dev/mtdblock8
$ dd if=openwrt.bin of=/dev/mtdblock9
6. Reboot the device. It should boot into OpenWrt.
Signed-off-by: David Bauer <mail at david-bauer.net>
(cherry picked from commit 634c13c186646aff2badb51a43b248825d0fe5a0)
---
.../base-files/lib/preinit/05_set_preinit_iface | 10 +-
.../boot/dts/mediatek/mt7622-ubnt-unifi-6-lr.dts | 327 +++++++++++++++++++++
target/linux/mediatek/image/mt7622.mk | 9 +
.../mt7622/base-files/etc/board.d/02_network | 3 +
target/linux/mediatek/mt7622/config-5.4 | 6 +-
.../patches-5.4/1020-spi-nor-w25q512jv.patch | 25 ++
6 files changed, 378 insertions(+), 2 deletions(-)
diff --git a/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface b/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface
index f39e8aee8d..3ac856d1c4 100644
--- a/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface
+++ b/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface
@@ -1,6 +1,14 @@
set_preinit_iface() {
ip link set eth0 up
- ifname=lan1
+
+ case $(board_name) in
+ ubnt,unifi-6-lr)
+ ifname=eth0
+ ;;
+ *)
+ ifname=lan1
+ ;;
+ esac
}
boot_hook_add preinit_main set_preinit_iface
diff --git a/target/linux/mediatek/files-5.4/arch/arm64/boot/dts/mediatek/mt7622-ubnt-unifi-6-lr.dts b/target/linux/mediatek/files-5.4/arch/arm64/boot/dts/mediatek/mt7622-ubnt-unifi-6-lr.dts
new file mode 100644
index 0000000000..1f410b1d47
--- /dev/null
+++ b/target/linux/mediatek/files-5.4/arch/arm64/boot/dts/mediatek/mt7622-ubnt-unifi-6-lr.dts
@@ -0,0 +1,327 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+#include "mt7622.dtsi"
+#include "mt6380.dtsi"
+
+/ {
+ model = "Ubiquiti UniFi 6 LR";
+ compatible = "ubnt,unifi-6-lr", "mediatek,mt7622";
+
+ aliases {
+ led-boot = &led_blue;
+ led-failsafe = &led_blue;
+ led-running = &led_blue;
+ led-upgrade = &led_blue;
+ label-mac-device = &gmac0;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ bootargs = "earlycon=uart8250,mmio32,0x11002000 swiotlb=512 console=ttyS0,115200n8";
+ };
+
+ cpus {
+ cpu at 0 {
+ proc-supply = <&mt6380_vcpu_reg>;
+ sram-supply = <&mt6380_vm_reg>;
+ };
+
+ cpu at 1 {
+ proc-supply = <&mt6380_vcpu_reg>;
+ sram-supply = <&mt6380_vm_reg>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&pio 62 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ memory {
+ reg = <0 0x40000000 0 0x3f000000>;
+ };
+
+ reg_1p8v: regulator-1p8v {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+};
+
+&pcie0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie0_pins>;
+ status = "okay";
+};
+
+&slot0 {
+ wifi at 0,0 {
+ reg = <0x0 0 0 0 0>;
+ mediatek,mtd-eeprom = <&factory 0x20000>;
+ mtd-mac-address = <&eeprom 0x6>;
+ ieee80211-freq-limit = <5000000 6000000>;
+ };
+};
+
+&pio {
+ eth_pins: eth-pins {
+ mux {
+ function = "eth";
+ groups = "mdc_mdio", "rgmii_via_gmac2";
+ };
+ };
+
+ pcie0_pins: pcie0-pins {
+ mux {
+ function = "pcie";
+ groups = "pcie0_pad_perst",
+ "pcie0_1_waken",
+ "pcie0_1_clkreq";
+ };
+ };
+
+ pcie1_pins: pcie1-pins {
+ mux {
+ function = "pcie";
+ groups = "pcie1_pad_perst",
+ "pcie1_0_waken",
+ "pcie1_0_clkreq";
+ };
+ };
+
+ pmic_bus_pins: pmic-bus-pins {
+ mux {
+ function = "pmic";
+ groups = "pmic_bus";
+ };
+ };
+
+ spi_nor_pins: spi-nor-pins {
+ mux {
+ function = "flash";
+ groups = "spi_nor";
+ };
+ };
+
+ uart0_pins: uart0-pins {
+ mux {
+ function = "uart";
+ groups = "uart0_0_tx_rx" ;
+ };
+ };
+
+ uart3_pins: uart3-pins {
+ mux {
+ function = "uart";
+ groups = "uart3_1_tx_rx" ;
+ };
+ };
+
+ i2c0_pins: i2c0-pins {
+ mux {
+ function = "i2c";
+ groups = "i2c0";
+ };
+ };
+
+ watchdog_pins: watchdog-pins {
+ mux {
+ function = "watchdog";
+ groups = "watchdog";
+ };
+ };
+};
+
+&bch {
+ status = "okay";
+};
+
+&btif {
+ status = "disabled";
+};
+
+ð {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <ð_pins>;
+
+ gmac0: mac at 0 {
+ compatible = "mediatek,eth-mac";
+ reg = <0>;
+
+ phy-mode = "2500base-x";
+ mtd-mac-address = <&eeprom 0x0>;
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ };
+ };
+
+ mdio: mdio-bus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet-phy at 8 {
+ /* Marvell AQRate AQR112W - no driver */
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x8>;
+ };
+ };
+};
+
+&pwrap {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_bus_pins>;
+
+ status = "okay";
+};
+
+&nor_flash {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_nor_pins>;
+
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "preloader";
+ reg = <0x0 0x40000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "atf";
+ reg = <0x40000 0x20000>;
+ read-only;
+ };
+
+ partition at 60000 {
+ label = "u-boot";
+ reg = <0x60000 0x60000>;
+ read-only;
+ };
+
+ partition at c0000 {
+ label = "u-boot-env";
+ reg = <0xc0000 0x10000>;
+ };
+
+ factory: partition at d0000 {
+ label = "factory";
+ reg = <0xd0000 0x40000>;
+ read-only;
+ };
+
+ eeprom: partition at 110000 {
+ label = "eeprom";
+ reg = <0x110000 0x10000>;
+ read-only;
+ };
+
+ partition at 120000 {
+ label = "bs";
+ reg = <0x120000 0x10000>;
+ };
+
+ partition at 130000 {
+ label = "cfg";
+ reg = <0x130000 0x100000>;
+ read-only;
+ };
+
+ partition at 230000 {
+ compatible = "denx,fit";
+ label = "firmware";
+ reg = <0x230000 0x1ee0000>;
+ };
+
+ partition at 2110000 {
+ label = "kernel1";
+ reg = <0x2110000 0x1ee0000>;
+ };
+ };
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+ status = "okay";
+
+ /* MT7915 Bluetooth */
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ status = "okay";
+
+ led-controller at 30 {
+ compatible = "ubnt,ledbar";
+ reg = <0x30>;
+
+ enable-gpio = <&pio 59 0>;
+
+ red {
+ label = "red";
+ };
+
+ green {
+ label = "green";
+ };
+
+ led_blue: blue {
+ label = "blue";
+ };
+ };
+};
+
+&watchdog {
+ pinctrl-names = "default";
+ pinctrl-0 = <&watchdog_pins>;
+ status = "okay";
+};
+
+&wmac {
+ mediatek,mtd-eeprom = <&factory 0x0>;
+ mtd-mac-address = <&eeprom 0x0>;
+ status = "okay";
+};
diff --git a/target/linux/mediatek/image/mt7622.mk b/target/linux/mediatek/image/mt7622.mk
index 0851184dcb..bf706930e4 100644
--- a/target/linux/mediatek/image/mt7622.mk
+++ b/target/linux/mediatek/image/mt7622.mk
@@ -58,3 +58,12 @@ define Device/mediatek_mt7622-ubi
DEVICE_PACKAGES := kmod-usb-ohci kmod-usb2 kmod-usb3 kmod-ata-ahci-mtk
endef
TARGET_DEVICES += mediatek_mt7622-ubi
+
+define Device/ubnt_unifi-6-lr
+ DEVICE_VENDOR := Ubiquiti
+ DEVICE_MODEL := UniFi 6 LR
+ DEVICE_DTS := mt7622-ubnt-unifi-6-lr
+ DEVICE_DTS_DIR := $(DTS_DIR)/mediatek
+ DEVICE_PACKAGES := kmod-mt7915e
+endef
+TARGET_DEVICES += ubnt_unifi-6-lr
diff --git a/target/linux/mediatek/mt7622/base-files/etc/board.d/02_network b/target/linux/mediatek/mt7622/base-files/etc/board.d/02_network
index 426d9937bf..3a409c8ec9 100755
--- a/target/linux/mediatek/mt7622/base-files/etc/board.d/02_network
+++ b/target/linux/mediatek/mt7622/base-files/etc/board.d/02_network
@@ -16,6 +16,9 @@ mediatek_setup_interfaces()
mediatek,mt7622-rfb1)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" wan
;;
+ ubnt,unifi-6-lr)
+ ucidef_set_interfaces_lan "eth0"
+ ;;
*)
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "6u at eth0" "5u at eth1"
diff --git a/target/linux/mediatek/mt7622/config-5.4 b/target/linux/mediatek/mt7622/config-5.4
index e92789697d..1b0b1e36a6 100644
--- a/target/linux/mediatek/mt7622/config-5.4
+++ b/target/linux/mediatek/mt7622/config-5.4
@@ -333,6 +333,10 @@ CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
CONFIG_HOLES_IN_ZONE=y
CONFIG_HZ=250
CONFIG_HZ_250=y
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_MT65XX=y
CONFIG_ICPLUS_PHY=y
CONFIG_IIO=y
CONFIG_IKCONFIG=y
@@ -536,7 +540,7 @@ CONFIG_SPI=y
CONFIG_SPI_MASTER=y
CONFIG_SPI_MEM=y
CONFIG_SPI_MT65XX=y
-# CONFIG_SPI_MTK_NOR is not set
+CONFIG_SPI_MTK_NOR=y
CONFIG_SPI_MTK_SNFI=y
CONFIG_SRCU=y
CONFIG_SWCONFIG=y
diff --git a/target/linux/mediatek/patches-5.4/1020-spi-nor-w25q512jv.patch b/target/linux/mediatek/patches-5.4/1020-spi-nor-w25q512jv.patch
new file mode 100644
index 0000000000..1a16574c2b
--- /dev/null
+++ b/target/linux/mediatek/patches-5.4/1020-spi-nor-w25q512jv.patch
@@ -0,0 +1,25 @@
+From: David Bauer <mail at david-bauer.net>
+Date: Thu, 11 Feb 2021 19:57:26 +0100
+Subject: [PATCH] mtd: spi-nor: add support for Winbond W25Q512
+
+The Winbond W25Q512 is a 512mb SPI-NOR chip. It supports 4K sectors as
+well as block protection and Dual-/Quad-read.
+
+Tested on: Ubiquiti UniFi 6 LR
+
+Signed-off-by: David Bauer <mail at david-bauer.net>
+
+Ref: https://patchwork.ozlabs.org/project/linux-mtd/patch/20210213151047.11700-1-mail@david-bauer.net/
+
+--- a/drivers/mtd/spi-nor/spi-nor.c
++++ b/drivers/mtd/spi-nor/spi-nor.c
+@@ -2550,6 +2550,9 @@ static const struct flash_info spi_nor_i
+ .fixups = &w25q256_fixups },
+ { "w25q256jvm", INFO(0xef7019, 0, 64 * 1024, 512,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
++ { "w25q512jv", INFO(0xef4020, 0, 64 * 1024, 1024,
++ SECT_4K | SPI_NOR_QUAD_READ | SPI_NOR_DUAL_READ |
++ SPI_NOR_HAS_TB | SPI_NOR_HAS_LOCK) },
+ { "w25m512jv", INFO(0xef7119, 0, 64 * 1024, 1024,
+ SECT_4K | SPI_NOR_QUAD_READ | SPI_NOR_DUAL_READ) },
+
More information about the lede-commits
mailing list