[openwrt/openwrt] bcm4908: add Ethernet driver
LEDE Commits
lede-commits at lists.infradead.org
Mon Feb 8 06:06:34 EST 2021
rmilecki pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/81240a9b8985de7aefe40e8ea3a3d1602094e555
commit 81240a9b8985de7aefe40e8ea3a3d1602094e555
Author: Rafał Miłecki <rafal at milecki.pl>
AuthorDate: Mon Feb 8 11:45:03 2021 +0100
bcm4908: add Ethernet driver
This commit picks up pending netdev patches.
Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
---
target/linux/bcm4908/config-5.4 | 1 +
.../drivers/net/ethernet/broadcom/unimac.h | 68 ++
...-net-document-BCM4908-Ethernet-controller.patch | 60 ++
...m-bcm4908enet-add-BCM4908-controller-driv.patch | 842 +++++++++++++++++++++
...roadcom-bcm4908-describe-Ethernet-control.patch | 49 ++
5 files changed, 1020 insertions(+)
diff --git a/target/linux/bcm4908/config-5.4 b/target/linux/bcm4908/config-5.4
index d13753c49d..2a3cd647fc 100644
--- a/target/linux/bcm4908/config-5.4
+++ b/target/linux/bcm4908/config-5.4
@@ -40,6 +40,7 @@ CONFIG_B53=y
# CONFIG_B53_MMAP_DRIVER is not set
# CONFIG_B53_SERDES is not set
# CONFIG_B53_SRAB_DRIVER is not set
+CONFIG_BCM4908ENET=y
CONFIG_BCM7XXX_PHY=y
CONFIG_BCM_NET_PHYLIB=y
CONFIG_BCM_PMB=y
diff --git a/target/linux/bcm4908/files-5.4/drivers/net/ethernet/broadcom/unimac.h b/target/linux/bcm4908/files-5.4/drivers/net/ethernet/broadcom/unimac.h
new file mode 100644
index 0000000000..585a852862
--- /dev/null
+++ b/target/linux/bcm4908/files-5.4/drivers/net/ethernet/broadcom/unimac.h
@@ -0,0 +1,68 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+#ifndef __UNIMAC_H
+#define __UNIMAC_H
+
+#define UMAC_HD_BKP_CTRL 0x004
+#define HD_FC_EN (1 << 0)
+#define HD_FC_BKOFF_OK (1 << 1)
+#define IPG_CONFIG_RX_SHIFT 2
+#define IPG_CONFIG_RX_MASK 0x1F
+#define UMAC_CMD 0x008
+#define CMD_TX_EN (1 << 0)
+#define CMD_RX_EN (1 << 1)
+#define CMD_SPEED_10 0
+#define CMD_SPEED_100 1
+#define CMD_SPEED_1000 2
+#define CMD_SPEED_2500 3
+#define CMD_SPEED_SHIFT 2
+#define CMD_SPEED_MASK 3
+#define CMD_PROMISC (1 << 4)
+#define CMD_PAD_EN (1 << 5)
+#define CMD_CRC_FWD (1 << 6)
+#define CMD_PAUSE_FWD (1 << 7)
+#define CMD_RX_PAUSE_IGNORE (1 << 8)
+#define CMD_TX_ADDR_INS (1 << 9)
+#define CMD_HD_EN (1 << 10)
+#define CMD_SW_RESET_OLD (1 << 11)
+#define CMD_SW_RESET (1 << 13)
+#define CMD_LCL_LOOP_EN (1 << 15)
+#define CMD_AUTO_CONFIG (1 << 22)
+#define CMD_CNTL_FRM_EN (1 << 23)
+#define CMD_NO_LEN_CHK (1 << 24)
+#define CMD_RMT_LOOP_EN (1 << 25)
+#define CMD_RX_ERR_DISC (1 << 26)
+#define CMD_PRBL_EN (1 << 27)
+#define CMD_TX_PAUSE_IGNORE (1 << 28)
+#define CMD_TX_RX_EN (1 << 29)
+#define CMD_RUNT_FILTER_DIS (1 << 30)
+#define UMAC_MAC0 0x00c
+#define UMAC_MAC1 0x010
+#define UMAC_MAX_FRAME_LEN 0x014
+#define UMAC_PAUSE_QUANTA 0x018
+#define UMAC_MODE 0x044
+#define MODE_LINK_STATUS (1 << 5)
+#define UMAC_FRM_TAG0 0x048 /* outer tag */
+#define UMAC_FRM_TAG1 0x04c /* inner tag */
+#define UMAC_TX_IPG_LEN 0x05c
+#define UMAC_EEE_CTRL 0x064
+#define EN_LPI_RX_PAUSE (1 << 0)
+#define EN_LPI_TX_PFC (1 << 1)
+#define EN_LPI_TX_PAUSE (1 << 2)
+#define EEE_EN (1 << 3)
+#define RX_FIFO_CHECK (1 << 4)
+#define EEE_TX_CLK_DIS (1 << 5)
+#define DIS_EEE_10M (1 << 6)
+#define LP_IDLE_PREDICTION_MODE (1 << 7)
+#define UMAC_EEE_LPI_TIMER 0x068
+#define UMAC_EEE_WAKE_TIMER 0x06C
+#define UMAC_EEE_REF_COUNT 0x070
+#define EEE_REFERENCE_COUNT_MASK 0xffff
+#define UMAC_RX_IPG_INV 0x078
+#define UMAC_MACSEC_PROG_TX_CRC 0x310
+#define UMAC_MACSEC_CTRL 0x314
+#define UMAC_PAUSE_CTRL 0x330
+#define UMAC_TX_FLUSH 0x334
+#define UMAC_RX_FIFO_STATUS 0x338
+#define UMAC_TX_FIFO_STATUS 0x33c
+
+#endif
diff --git a/target/linux/bcm4908/patches-5.4/170-0001-dt-bindings-net-document-BCM4908-Ethernet-controller.patch b/target/linux/bcm4908/patches-5.4/170-0001-dt-bindings-net-document-BCM4908-Ethernet-controller.patch
new file mode 100644
index 0000000000..4c0f44199b
--- /dev/null
+++ b/target/linux/bcm4908/patches-5.4/170-0001-dt-bindings-net-document-BCM4908-Ethernet-controller.patch
@@ -0,0 +1,60 @@
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
+Date: Fri, 5 Feb 2021 21:57:41 +0100
+Subject: [PATCH 1/2] dt-bindings: net: document BCM4908 Ethernet controller
+
+BCM4908 is a family of SoCs with integrated Ethernet controller.
+
+Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
+---
+ .../bindings/net/brcm,bcm4908enet.yaml | 45 +++++++++++++++++++
+ 1 file changed, 45 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/net/brcm,bcm4908enet.yaml
+
+--- /dev/null
++++ b/Documentation/devicetree/bindings/net/brcm,bcm4908enet.yaml
+@@ -0,0 +1,45 @@
++# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
++%YAML 1.2
++---
++$id: http://devicetree.org/schemas/net/brcm,bcm4908enet.yaml#
++$schema: http://devicetree.org/meta-schemas/core.yaml#
++
++title: Broadcom BCM4908 Ethernet controller
++
++description: Broadcom's Ethernet controller integrated into BCM4908 family SoCs
++
++maintainers:
++ - Rafał Miłecki <rafal at milecki.pl>
++
++properties:
++ compatible:
++ const: brcm,bcm4908enet
++
++ reg:
++ maxItems: 1
++
++ interrupts:
++ description: RX interrupt
++
++ interrupt-names:
++ const: rx
++
++required:
++ - reg
++ - interrupts
++ - interrupt-names
++
++additionalProperties: false
++
++examples:
++ - |
++ #include <dt-bindings/interrupt-controller/irq.h>
++ #include <dt-bindings/interrupt-controller/arm-gic.h>
++
++ ethernet at 80002000 {
++ compatible = "brcm,bcm4908enet";
++ reg = <0x80002000 0x1000>;
++
++ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
++ interrupt-names = "rx";
++ };
diff --git a/target/linux/bcm4908/patches-5.4/170-0002-net-broadcom-bcm4908enet-add-BCM4908-controller-driv.patch b/target/linux/bcm4908/patches-5.4/170-0002-net-broadcom-bcm4908enet-add-BCM4908-controller-driv.patch
new file mode 100644
index 0000000000..5b2084e80c
--- /dev/null
+++ b/target/linux/bcm4908/patches-5.4/170-0002-net-broadcom-bcm4908enet-add-BCM4908-controller-driv.patch
@@ -0,0 +1,842 @@
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
+Date: Fri, 5 Feb 2021 21:59:51 +0100
+Subject: [PATCH 2/2] net: broadcom: bcm4908enet: add BCM4908 controller driver
+
+BCM4908 SoCs family uses Ethernel controller that includes UniMAC but
+uses different DMA engine (than other controllers) and requires
+different programming.
+
+Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
+---
+ MAINTAINERS | 9 +
+ drivers/net/ethernet/broadcom/Kconfig | 8 +
+ drivers/net/ethernet/broadcom/Makefile | 1 +
+ drivers/net/ethernet/broadcom/bcm4908enet.c | 676 ++++++++++++++++++++
+ drivers/net/ethernet/broadcom/bcm4908enet.h | 96 +++
+ 5 files changed, 790 insertions(+)
+ create mode 100644 drivers/net/ethernet/broadcom/bcm4908enet.c
+ create mode 100644 drivers/net/ethernet/broadcom/bcm4908enet.h
+
+--- a/MAINTAINERS
++++ b/MAINTAINERS
+@@ -3207,6 +3207,15 @@ F: Documentation/devicetree/bindings/mip
+ F: arch/mips/bcm47xx/*
+ F: arch/mips/include/asm/mach-bcm47xx/*
+
++BROADCOM BCM4908 ETHERNET DRIVER
++M: Rafał Miłecki <rafal at milecki.pl>
++M: bcm-kernel-feedback-list at broadcom.com
++L: netdev at vger.kernel.org
++S: Maintained
++F: Documentation/devicetree/bindings/net/brcm,bcm4908enet.yaml
++F: drivers/net/ethernet/broadcom/bcm4908enet.*
++F: drivers/net/ethernet/broadcom/unimac.h
++
+ BROADCOM BCM5301X ARM ARCHITECTURE
+ M: Hauke Mehrtens <hauke at hauke-m.de>
+ M: Rafał Miłecki <zajec5 at gmail.com>
+--- a/drivers/net/ethernet/broadcom/Kconfig
++++ b/drivers/net/ethernet/broadcom/Kconfig
+@@ -51,6 +51,14 @@ config B44_PCI
+ depends on B44_PCI_AUTOSELECT && B44_PCICORE_AUTOSELECT
+ default y
+
++config BCM4908ENET
++ tristate "Broadcom BCM4908 internal mac support"
++ depends on ARCH_BCM4908 || COMPILE_TEST
++ default y
++ help
++ This driver supports Ethernet controller integrated into Broadcom
++ BCM4908 family SoCs.
++
+ config BCM63XX_ENET
+ tristate "Broadcom 63xx internal mac support"
+ depends on BCM63XX
+--- a/drivers/net/ethernet/broadcom/Makefile
++++ b/drivers/net/ethernet/broadcom/Makefile
+@@ -4,6 +4,7 @@
+ #
+
+ obj-$(CONFIG_B44) += b44.o
++obj-$(CONFIG_BCM4908ENET) += bcm4908enet.o
+ obj-$(CONFIG_BCM63XX_ENET) += bcm63xx_enet.o
+ obj-$(CONFIG_BCMGENET) += genet/
+ obj-$(CONFIG_BNX2) += bnx2.o
+--- /dev/null
++++ b/drivers/net/ethernet/broadcom/bcm4908enet.c
+@@ -0,0 +1,676 @@
++// SPDX-License-Identifier: GPL-2.0-only
++/*
++ * Copyright (C) 2021 Rafał Miłecki <rafal at milecki.pl>
++ */
++
++#include <linux/delay.h>
++#include <linux/etherdevice.h>
++#include <linux/interrupt.h>
++#include <linux/module.h>
++#include <linux/of.h>
++#include <linux/platform_device.h>
++#include <linux/slab.h>
++#include <linux/string.h>
++
++#include "bcm4908enet.h"
++#include "unimac.h"
++
++#define ENET_DMA_CH_RX_CFG ENET_DMA_CH0_CFG
++#define ENET_DMA_CH_TX_CFG ENET_DMA_CH1_CFG
++#define ENET_DMA_CH_RX_STATE_RAM ENET_DMA_CH0_STATE_RAM
++#define ENET_DMA_CH_TX_STATE_RAM ENET_DMA_CH1_STATE_RAM
++
++#define ENET_TX_BDS_NUM 200
++#define ENET_RX_BDS_NUM 200
++#define ENET_RX_BDS_NUM_MAX 8192
++
++#define ENET_DMA_INT_DEFAULTS (ENET_DMA_CH_CFG_INT_DONE | \
++ ENET_DMA_CH_CFG_INT_NO_DESC | \
++ ENET_DMA_CH_CFG_INT_BUFF_DONE)
++#define ENET_DMA_MAX_BURST_LEN 8 /* in 64 bit words */
++
++#define ENET_MTU_MIN 60
++#define ENET_MTU_MAX 1500 /* Is it possible to support 2044? */
++#define ENET_MTU_MAX_EXTRA_SIZE 32 /* L2 */
++
++struct bcm4908enet_dma_ring_bd {
++ __le32 ctl;
++ __le32 addr;
++} __packed;
++
++struct bcm4908enet_dma_ring_slot {
++ struct sk_buff *skb;
++ unsigned int len;
++ dma_addr_t dma_addr;
++};
++
++struct bcm4908enet_dma_ring {
++ int is_tx;
++ int read_idx;
++ int write_idx;
++ int length;
++ u16 cfg_block;
++ u16 st_ram_block;
++
++ union {
++ void *cpu_addr;
++ struct bcm4908enet_dma_ring_bd *buf_desc;
++ };
++ dma_addr_t dma_addr;
++
++ struct bcm4908enet_dma_ring_slot *slots;
++};
++
++struct bcm4908enet {
++ struct device *dev;
++ struct net_device *netdev;
++ struct napi_struct napi;
++ void __iomem *base;
++
++ struct bcm4908enet_dma_ring tx_ring;
++ struct bcm4908enet_dma_ring rx_ring;
++};
++
++/***
++ * R/W ops
++ */
++
++static inline u32 enet_read(struct bcm4908enet *enet, u16 offset)
++{
++ return readl(enet->base + offset);
++}
++
++static inline void enet_write(struct bcm4908enet *enet, u16 offset, u32 value)
++{
++ writel(value, enet->base + offset);
++}
++
++static inline void enet_maskset(struct bcm4908enet *enet, u16 offset, u32 mask, u32 set)
++{
++ u32 val;
++
++ WARN_ON(set & ~mask);
++
++ val = enet_read(enet, offset);
++ val = (val & ~mask) | (set & mask);
++ enet_write(enet, offset, val);
++}
++
++static inline void enet_set(struct bcm4908enet *enet, u16 offset, u32 set)
++{
++ enet_maskset(enet, offset, set, set);
++}
++
++static inline u32 enet_umac_read(struct bcm4908enet *enet, u16 offset)
++{
++ return enet_read(enet, ENET_UNIMAC + offset);
++}
++
++static inline void enet_umac_write(struct bcm4908enet *enet, u16 offset, u32 value)
++{
++ enet_write(enet, ENET_UNIMAC + offset, value);
++}
++
++static inline void enet_umac_maskset(struct bcm4908enet *enet, u16 offset, u32 mask, u32 set)
++{
++ enet_maskset(enet, ENET_UNIMAC + offset, mask, set);
++}
++
++static inline void enet_umac_set(struct bcm4908enet *enet, u16 offset, u32 set)
++{
++ enet_set(enet, ENET_UNIMAC + offset, set);
++}
++
++/***
++ * Helpers
++ */
++
++static void bcm4908enet_intrs_on(struct bcm4908enet *enet)
++{
++ enet_write(enet, ENET_DMA_CH_RX_CFG + ENET_DMA_CH_CFG_INT_MASK, ENET_DMA_INT_DEFAULTS);
++}
++
++static void bcm4908enet_intrs_off(struct bcm4908enet *enet)
++{
++ enet_write(enet, ENET_DMA_CH_RX_CFG + ENET_DMA_CH_CFG_INT_MASK, 0);
++}
++
++static void bcm4908enet_intrs_ack(struct bcm4908enet *enet)
++{
++ enet_write(enet, ENET_DMA_CH_RX_CFG + ENET_DMA_CH_CFG_INT_STAT, ENET_DMA_INT_DEFAULTS);
++}
++
++/***
++ * DMA
++ */
++
++static int bcm4908_dma_alloc_buf_descs(struct bcm4908enet *enet, struct bcm4908enet_dma_ring *ring)
++{
++ int size = ring->length * sizeof(struct bcm4908enet_dma_ring_bd);
++ struct device *dev = enet->dev;
++
++ ring->cpu_addr = dma_alloc_coherent(dev, size, &ring->dma_addr, GFP_KERNEL);
++ if (!ring->cpu_addr)
++ return -ENOMEM;
++
++ if (((uintptr_t)ring->cpu_addr) & (0x40 - 1)) {
++ dev_err(dev, "Invalid DMA ring alignment\n");
++ goto err_free_buf_descs;
++ }
++
++ ring->slots = kzalloc(ring->length * sizeof(*ring->slots), GFP_KERNEL);
++ if (!ring->slots)
++ goto err_free_buf_descs;
++
++ memset(ring->cpu_addr, 0, size);
++
++ ring->read_idx = 0;
++ ring->write_idx = 0;
++
++ return 0;
++
++err_free_buf_descs:
++ dma_free_coherent(dev, size, ring->cpu_addr, ring->dma_addr);
++ return -ENOMEM;
++}
++
++static void bcm4908enet_dma_free(struct bcm4908enet *enet)
++{
++ struct bcm4908enet_dma_ring *tx_ring = &enet->tx_ring;
++ struct bcm4908enet_dma_ring *rx_ring = &enet->rx_ring;
++ struct device *dev = enet->dev;
++ int size;
++
++ size = rx_ring->length * sizeof(struct bcm4908enet_dma_ring_bd);
++ if (rx_ring->cpu_addr)
++ dma_free_coherent(dev, size, rx_ring->cpu_addr, rx_ring->dma_addr);
++ kfree(rx_ring->slots);
++
++ size = tx_ring->length * sizeof(struct bcm4908enet_dma_ring_bd);
++ if (tx_ring->cpu_addr)
++ dma_free_coherent(dev, size, tx_ring->cpu_addr, tx_ring->dma_addr);
++ kfree(tx_ring->slots);
++}
++
++static int bcm4908enet_dma_alloc(struct bcm4908enet *enet)
++{
++ struct bcm4908enet_dma_ring *tx_ring = &enet->tx_ring;
++ struct bcm4908enet_dma_ring *rx_ring = &enet->rx_ring;
++ struct device *dev = enet->dev;
++ int err;
++
++ tx_ring->length = ENET_TX_BDS_NUM;
++ tx_ring->is_tx = 1;
++ tx_ring->cfg_block = ENET_DMA_CH_TX_CFG;
++ tx_ring->st_ram_block = ENET_DMA_CH_TX_STATE_RAM;
++ err = bcm4908_dma_alloc_buf_descs(enet, tx_ring);
++ if (err) {
++ dev_err(dev, "Failed to alloc TX buf descriptors: %d\n", err);
++ return err;
++ }
++
++ rx_ring->length = ENET_RX_BDS_NUM;
++ rx_ring->is_tx = 0;
++ rx_ring->cfg_block = ENET_DMA_CH_RX_CFG;
++ rx_ring->st_ram_block = ENET_DMA_CH_RX_STATE_RAM;
++ err = bcm4908_dma_alloc_buf_descs(enet, rx_ring);
++ if (err) {
++ dev_err(dev, "Failed to alloc RX buf descriptors: %d\n", err);
++ bcm4908enet_dma_free(enet);
++ return err;
++ }
++
++ return 0;
++}
++
++static void bcm4908enet_dma_reset(struct bcm4908enet *enet)
++{
++ struct bcm4908enet_dma_ring *rings[] = { &enet->rx_ring, &enet->tx_ring };
++ int i;
++
++ /* Disable the DMA controller and channel */
++ for (i = 0; i < ARRAY_SIZE(rings); i++)
++ enet_write(enet, rings[i]->cfg_block + ENET_DMA_CH_CFG, 0);
++ enet_maskset(enet, ENET_DMA_CONTROLLER_CFG, ENET_DMA_CTRL_CFG_MASTER_EN, 0);
++
++ /* Reset channels state */
++ for (i = 0; i < ARRAY_SIZE(rings); i++) {
++ struct bcm4908enet_dma_ring *ring = rings[i];
++
++ enet_write(enet, ring->st_ram_block + ENET_DMA_CH_STATE_RAM_BASE_DESC_PTR, 0);
++ enet_write(enet, ring->st_ram_block + ENET_DMA_CH_STATE_RAM_STATE_DATA, 0);
++ enet_write(enet, ring->st_ram_block + ENET_DMA_CH_STATE_RAM_DESC_LEN_STATUS, 0);
++ enet_write(enet, ring->st_ram_block + ENET_DMA_CH_STATE_RAM_DESC_BASE_BUFPTR, 0);
++ }
++}
++
++static int bcm4908enet_dma_alloc_rx_buf(struct bcm4908enet *enet, unsigned int idx)
++{
++ struct bcm4908enet_dma_ring_bd *buf_desc = &enet->rx_ring.buf_desc[idx];
++ struct bcm4908enet_dma_ring_slot *slot = &enet->rx_ring.slots[idx];
++ struct device *dev = enet->dev;
++ u32 tmp;
++ int err;
++
++ slot->len = ENET_MTU_MAX + ENET_MTU_MAX_EXTRA_SIZE;
++
++ slot->skb = netdev_alloc_skb(enet->netdev, slot->len);
++ if (!slot->skb)
++ return -ENOMEM;
++
++ slot->dma_addr = dma_map_single(dev, slot->skb->data, slot->len, DMA_FROM_DEVICE);
++ err = dma_mapping_error(dev, slot->dma_addr);
++ if (err) {
++ dev_err(dev, "Failed to map DMA buffer: %d\n", err);
++ kfree_skb(slot->skb);
++ slot->skb = NULL;
++ return err;
++ }
++
++ tmp = slot->len << DMA_CTL_LEN_DESC_BUFLENGTH_SHIFT;
++ tmp |= DMA_CTL_STATUS_OWN;
++ if (idx == enet->rx_ring.length - 1)
++ tmp |= DMA_CTL_STATUS_WRAP;
++ buf_desc->ctl = cpu_to_le32(tmp);
++ buf_desc->addr = cpu_to_le32(slot->dma_addr);
++
++ return 0;
++}
++
++static void bcm4908enet_dma_ring_init(struct bcm4908enet *enet,
++ struct bcm4908enet_dma_ring *ring)
++{
++ int reset_channel = 0; /* We support only 1 main channel (with TX and RX) */
++ int reset_subch = ring->is_tx ? 1 : 0;
++
++ /* Reset the DMA channel */
++ enet_write(enet, ENET_DMA_CTRL_CHANNEL_RESET, BIT(reset_channel * 2 + reset_subch));
++ enet_write(enet, ENET_DMA_CTRL_CHANNEL_RESET, 0);
++
++ enet_write(enet, ring->cfg_block + ENET_DMA_CH_CFG, 0);
++ enet_write(enet, ring->cfg_block + ENET_DMA_CH_CFG_MAX_BURST, ENET_DMA_MAX_BURST_LEN);
++ enet_write(enet, ring->cfg_block + ENET_DMA_CH_CFG_INT_MASK, 0);
++
++ enet_write(enet, ring->st_ram_block + ENET_DMA_CH_STATE_RAM_BASE_DESC_PTR,
++ (uint32_t)ring->dma_addr);
++}
++
++static void bcm4908enet_dma_uninit(struct bcm4908enet *enet)
++{
++ struct bcm4908enet_dma_ring *rx_ring = &enet->rx_ring;
++ struct bcm4908enet_dma_ring_slot *slot;
++ struct device *dev = enet->dev;
++ int i;
++
++ for (i = rx_ring->length - 1; i >= 0; i--) {
++ slot = &rx_ring->slots[i];
++ if (!slot->skb)
++ continue;
++ dma_unmap_single(dev, slot->dma_addr, slot->len, DMA_FROM_DEVICE);
++ kfree_skb(slot->skb);
++ slot->skb = NULL;
++ }
++}
++
++static int bcm4908enet_dma_init(struct bcm4908enet *enet)
++{
++ struct bcm4908enet_dma_ring *rx_ring = &enet->rx_ring;
++ struct device *dev = enet->dev;
++ int err;
++ int i;
++
++ for (i = 0; i < rx_ring->length; i++) {
++ err = bcm4908enet_dma_alloc_rx_buf(enet, i);
++ if (err) {
++ dev_err(dev, "Failed to alloc RX buffer: %d\n", err);
++ bcm4908enet_dma_uninit(enet);
++ return err;
++ }
++ }
++
++ bcm4908enet_dma_ring_init(enet, &enet->tx_ring);
++ bcm4908enet_dma_ring_init(enet, &enet->rx_ring);
++
++ return 0;
++}
++
++static void bcm4908enet_dma_tx_ring_ensable(struct bcm4908enet *enet,
++ struct bcm4908enet_dma_ring *ring)
++{
++ enet_write(enet, ring->cfg_block + ENET_DMA_CH_CFG, ENET_DMA_CH_CFG_ENABLE);
++}
++
++static void bcm4908enet_dma_tx_ring_disable(struct bcm4908enet *enet,
++ struct bcm4908enet_dma_ring *ring)
++{
++ enet_write(enet, ring->cfg_block + ENET_DMA_CH_CFG, 0);
++}
++
++static void bcm4908enet_dma_rx_ring_enable(struct bcm4908enet *enet,
++ struct bcm4908enet_dma_ring *ring)
++{
++ enet_set(enet, ring->cfg_block + ENET_DMA_CH_CFG, ENET_DMA_CH_CFG_ENABLE);
++}
++
++static void bcm4908enet_dma_rx_ring_disable(struct bcm4908enet *enet,
++ struct bcm4908enet_dma_ring *ring)
++{
++ unsigned long deadline;
++ u32 tmp;
++
++ enet_maskset(enet, ring->cfg_block + ENET_DMA_CH_CFG, ENET_DMA_CH_CFG_ENABLE, 0);
++
++ deadline = jiffies + usecs_to_jiffies(2000);
++ do {
++ tmp = enet_read(enet, ring->cfg_block + ENET_DMA_CH_CFG);
++ if (!(tmp & ENET_DMA_CH_CFG_ENABLE))
++ return;
++ enet_maskset(enet, ring->cfg_block + ENET_DMA_CH_CFG, ENET_DMA_CH_CFG_ENABLE, 0);
++ usleep_range(10, 30);
++ } while (!time_after_eq(jiffies, deadline));
++
++ dev_warn(enet->dev, "Timeout waiting for DMA TX stop\n");
++}
++
++/***
++ * Ethernet driver
++ */
++
++static void bcm4908enet_gmac_init(struct bcm4908enet *enet)
++{
++ u32 cmd;
++
++ cmd = enet_umac_read(enet, UMAC_CMD);
++ enet_umac_write(enet, UMAC_CMD, cmd | CMD_SW_RESET);
++ enet_umac_write(enet, UMAC_CMD, cmd & ~CMD_SW_RESET);
++
++ enet_set(enet, ENET_FLUSH, ENET_FLUSH_RXFIFO_FLUSH | ENET_FLUSH_TXFIFO_FLUSH);
++ enet_maskset(enet, ENET_FLUSH, ENET_FLUSH_RXFIFO_FLUSH | ENET_FLUSH_TXFIFO_FLUSH, 0);
++
++ enet_set(enet, ENET_MIB_CTRL, ENET_MIB_CTRL_CLR_MIB);
++ enet_maskset(enet, ENET_MIB_CTRL, ENET_MIB_CTRL_CLR_MIB, 0);
++
++ cmd = enet_umac_read(enet, UMAC_CMD);
++ cmd &= ~(CMD_SPEED_MASK << CMD_SPEED_SHIFT);
++ cmd &= ~CMD_TX_EN;
++ cmd &= ~CMD_RX_EN;
++ cmd |= CMD_SPEED_1000 << CMD_SPEED_SHIFT;
++ enet_umac_write(enet, UMAC_CMD, cmd);
++
++ enet_maskset(enet, ENET_GMAC_STATUS,
++ ENET_GMAC_STATUS_ETH_SPEED_MASK |
++ ENET_GMAC_STATUS_HD |
++ ENET_GMAC_STATUS_AUTO_CFG_EN |
++ ENET_GMAC_STATUS_LINK_UP,
++ ENET_GMAC_STATUS_ETH_SPEED_1000 |
++ ENET_GMAC_STATUS_AUTO_CFG_EN |
++ ENET_GMAC_STATUS_LINK_UP);
++}
++
++static irqreturn_t bcm4908enet_irq_handler(int irq, void *dev_id)
++{
++ struct bcm4908enet *enet = dev_id;
++
++ bcm4908enet_intrs_off(enet);
++ bcm4908enet_intrs_ack(enet);
++
++ napi_schedule(&enet->napi);
++
++ return IRQ_HANDLED;
++}
++
++static int bcm4908enet_open(struct net_device *netdev)
++{
++ struct bcm4908enet *enet = netdev_priv(netdev);
++ struct device *dev = enet->dev;
++ int err;
++
++ err = request_irq(netdev->irq, bcm4908enet_irq_handler, 0, "enet", enet);
++ if (err) {
++ dev_err(dev, "Failed to request IRQ %d: %d\n", netdev->irq, err);
++ return err;
++ }
++
++ bcm4908enet_gmac_init(enet);
++ bcm4908enet_dma_reset(enet);
++ bcm4908enet_dma_init(enet);
++
++ enet_umac_set(enet, UMAC_CMD, CMD_TX_EN | CMD_RX_EN);
++
++ enet_set(enet, ENET_DMA_CONTROLLER_CFG, ENET_DMA_CTRL_CFG_MASTER_EN);
++ enet_maskset(enet, ENET_DMA_CONTROLLER_CFG, ENET_DMA_CTRL_CFG_FLOWC_CH1_EN, 0);
++ bcm4908enet_dma_rx_ring_enable(enet, &enet->rx_ring);
++
++ napi_enable(&enet->napi);
++ netif_carrier_on(netdev);
++ netif_start_queue(netdev);
++
++ bcm4908enet_intrs_ack(enet);
++ bcm4908enet_intrs_on(enet);
++
++ return 0;
++}
++
++static int bcm4908enet_stop(struct net_device *netdev)
++{
++ struct bcm4908enet *enet = netdev_priv(netdev);
++
++ netif_stop_queue(netdev);
++ netif_carrier_off(netdev);
++ napi_disable(&enet->napi);
++
++ bcm4908enet_dma_rx_ring_disable(enet, &enet->rx_ring);
++ bcm4908enet_dma_tx_ring_disable(enet, &enet->tx_ring);
++
++ bcm4908enet_dma_uninit(enet);
++
++ free_irq(enet->netdev->irq, enet);
++
++ return 0;
++}
++
++static int bcm4908enet_start_xmit(struct sk_buff *skb, struct net_device *netdev)
++{
++ struct bcm4908enet *enet = netdev_priv(netdev);
++ struct bcm4908enet_dma_ring *ring = &enet->tx_ring;
++ struct bcm4908enet_dma_ring_slot *slot;
++ struct device *dev = enet->dev;
++ struct bcm4908enet_dma_ring_bd *buf_desc;
++ int free_buf_descs;
++ u32 tmp;
++
++ /* Free transmitted skbs */
++ while (ring->read_idx != ring->write_idx) {
++ buf_desc = &ring->buf_desc[ring->read_idx];
++ if (buf_desc->ctl & DMA_CTL_STATUS_OWN)
++ break;
++ slot = &ring->slots[ring->read_idx];
++
++ dma_unmap_single(dev, slot->dma_addr, slot->len, DMA_TO_DEVICE);
++ dev_kfree_skb(slot->skb);
++ if (++ring->read_idx == ring->length)
++ ring->read_idx = 0;
++ }
++
++ /* Don't use the last empty buf descriptor */
++ if (ring->read_idx <= ring->write_idx)
++ free_buf_descs = ring->read_idx - ring->write_idx + ring->length;
++ else
++ free_buf_descs = ring->read_idx - ring->write_idx;
++ if (free_buf_descs < 2)
++ return NETDEV_TX_BUSY;
++
++ /* Hardware removes OWN bit after sending data */
++ buf_desc = &ring->buf_desc[ring->write_idx];
++ if (unlikely(le32_to_cpu(buf_desc->ctl) & DMA_CTL_STATUS_OWN)) {
++ netif_stop_queue(netdev);
++ return NETDEV_TX_BUSY;
++ }
++
++ slot = &ring->slots[ring->write_idx];
++ slot->skb = skb;
++ slot->len = skb->len;
++ slot->dma_addr = dma_map_single(dev, skb->data, skb->len, DMA_TO_DEVICE);
++ if (unlikely(dma_mapping_error(dev, slot->dma_addr)))
++ return NETDEV_TX_BUSY;
++
++ tmp = skb->len << DMA_CTL_LEN_DESC_BUFLENGTH_SHIFT;
++ tmp |= DMA_CTL_STATUS_OWN;
++ tmp |= DMA_CTL_STATUS_SOP;
++ tmp |= DMA_CTL_STATUS_EOP;
++ tmp |= DMA_CTL_STATUS_APPEND_CRC;
++ if (ring->write_idx + 1 == ring->length - 1)
++ tmp |= DMA_CTL_STATUS_WRAP;
++
++ buf_desc->addr = cpu_to_le32((uint32_t)slot->dma_addr);
++ buf_desc->ctl = cpu_to_le32(tmp);
++
++ bcm4908enet_dma_tx_ring_ensable(enet, &enet->tx_ring);
++
++ if (++ring->write_idx == ring->length - 1)
++ ring->write_idx = 0;
++ enet->netdev->stats.tx_bytes += skb->len;
++ enet->netdev->stats.tx_packets++;
++
++ return NETDEV_TX_OK;
++}
++
++static int bcm4908enet_poll(struct napi_struct *napi, int weight)
++{
++ struct bcm4908enet *enet = container_of(napi, struct bcm4908enet, napi);
++ struct device *dev = enet->dev;
++ int handled = 0;
++
++ while (handled < weight) {
++ struct bcm4908enet_dma_ring_bd *buf_desc;
++ struct bcm4908enet_dma_ring_slot slot;
++ u32 ctl;
++ int len;
++ int err;
++
++ buf_desc = &enet->rx_ring.buf_desc[enet->rx_ring.read_idx];
++ ctl = le32_to_cpu(buf_desc->ctl);
++ if (ctl & DMA_CTL_STATUS_OWN)
++ break;
++
++ slot = enet->rx_ring.slots[enet->rx_ring.read_idx];
++
++ /* Provide new buffer before unpinning the old one */
++ err = bcm4908enet_dma_alloc_rx_buf(enet, enet->rx_ring.read_idx);
++ if (err)
++ break;
++
++ if (++enet->rx_ring.read_idx == enet->rx_ring.length)
++ enet->rx_ring.read_idx = 0;
++
++ len = (ctl & DMA_CTL_LEN_DESC_BUFLENGTH) >> DMA_CTL_LEN_DESC_BUFLENGTH_SHIFT;
++
++ if (len < ENET_MTU_MIN ||
++ (ctl & (DMA_CTL_STATUS_SOP | DMA_CTL_STATUS_EOP)) != (DMA_CTL_STATUS_SOP | DMA_CTL_STATUS_EOP)) {
++ enet->netdev->stats.rx_dropped++;
++ break;
++ }
++
++ dma_unmap_single(dev, slot.dma_addr, slot.len, DMA_FROM_DEVICE);
++
++ skb_put(slot.skb, len - 4 + 2);
++ slot.skb->protocol = eth_type_trans(slot.skb, enet->netdev);
++ netif_receive_skb(slot.skb);
++
++ enet->netdev->stats.rx_packets++;
++ enet->netdev->stats.rx_bytes += len;
++ }
++
++ if (handled < weight) {
++ napi_complete_done(napi, handled);
++ bcm4908enet_intrs_on(enet);
++ }
++
++ return handled;
++}
++
++static const struct net_device_ops bcm96xx_netdev_ops = {
++ .ndo_open = bcm4908enet_open,
++ .ndo_stop = bcm4908enet_stop,
++ .ndo_start_xmit = bcm4908enet_start_xmit,
++ .ndo_set_mac_address = eth_mac_addr,
++};
++
++static int bcm4908enet_probe(struct platform_device *pdev)
++{
++ struct device *dev = &pdev->dev;
++ struct net_device *netdev;
++ struct bcm4908enet *enet;
++ int err;
++
++ netdev = devm_alloc_etherdev(dev, sizeof(*enet));
++ if (!netdev)
++ return -ENOMEM;
++
++ enet = netdev_priv(netdev);
++ enet->dev = dev;
++ enet->netdev = netdev;
++
++ enet->base = devm_platform_ioremap_resource(pdev, 0);
++ if (IS_ERR(enet->base)) {
++ dev_err(dev, "Failed to map registers: %ld\n", PTR_ERR(enet->base));
++ return PTR_ERR(enet->base);
++ }
++
++ netdev->irq = platform_get_irq_byname(pdev, "rx");
++ if (netdev->irq < 0)
++ return netdev->irq;
++
++ dma_set_coherent_mask(dev, DMA_BIT_MASK(32));
++
++ err = bcm4908enet_dma_alloc(enet);
++ if (err)
++ return err;
++
++ SET_NETDEV_DEV(netdev, &pdev->dev);
++ eth_hw_addr_random(netdev);
++ netdev->netdev_ops = &bcm96xx_netdev_ops;
++ netdev->min_mtu = ETH_ZLEN;
++ netdev->mtu = ENET_MTU_MAX;
++ netdev->max_mtu = ENET_MTU_MAX;
++ netif_napi_add(netdev, &enet->napi, bcm4908enet_poll, 64);
++
++ err = register_netdev(netdev);
++ if (err) {
++ bcm4908enet_dma_free(enet);
++ return err;
++ }
++
++ platform_set_drvdata(pdev, enet);
++
++ return 0;
++}
++
++static int bcm4908enet_remove(struct platform_device *pdev)
++{
++ struct bcm4908enet *enet = platform_get_drvdata(pdev);
++
++ unregister_netdev(enet->netdev);
++ netif_napi_del(&enet->napi);
++ bcm4908enet_dma_free(enet);
++
++ return 0;
++}
++
++static const struct of_device_id bcm4908enet_of_match[] = {
++ { .compatible = "brcm,bcm4908enet"},
++ {},
++};
++
++static struct platform_driver bcm4908enet_driver = {
++ .driver = {
++ .name = "bcm4908enet",
++ .of_match_table = bcm4908enet_of_match,
++ },
++ .probe = bcm4908enet_probe,
++ .remove = bcm4908enet_remove,
++};
++module_platform_driver(bcm4908enet_driver);
++
++MODULE_LICENSE("GPL v2");
++MODULE_DEVICE_TABLE(of, bcm4908enet_of_match);
+--- /dev/null
++++ b/drivers/net/ethernet/broadcom/bcm4908enet.h
+@@ -0,0 +1,96 @@
++/* SPDX-License-Identifier: GPL-2.0-only */
++#ifndef __BCM4908ENET_H
++#define __BCM4908ENET_H
++
++#define ENET_CONTROL 0x000
++#define ENET_MIB_CTRL 0x004
++#define ENET_MIB_CTRL_CLR_MIB 0x00000001
++#define ENET_RX_ERR_MASK 0x008
++#define ENET_MIB_MAX_PKT_SIZE 0x00C
++#define ENET_MIB_MAX_PKT_SIZE_VAL 0x00003fff
++#define ENET_DIAG_OUT 0x01c
++#define ENET_ENABLE_DROP_PKT 0x020
++#define ENET_IRQ_ENABLE 0x024
++#define ENET_IRQ_ENABLE_OVFL 0x00000001
++#define ENET_GMAC_STATUS 0x028
++#define ENET_GMAC_STATUS_ETH_SPEED_MASK 0x00000003
++#define ENET_GMAC_STATUS_ETH_SPEED_10 0x00000000
++#define ENET_GMAC_STATUS_ETH_SPEED_100 0x00000001
++#define ENET_GMAC_STATUS_ETH_SPEED_1000 0x00000002
++#define ENET_GMAC_STATUS_HD 0x00000004
++#define ENET_GMAC_STATUS_AUTO_CFG_EN 0x00000008
++#define ENET_GMAC_STATUS_LINK_UP 0x00000010
++#define ENET_IRQ_STATUS 0x02c
++#define ENET_IRQ_STATUS_OVFL 0x00000001
++#define ENET_OVERFLOW_COUNTER 0x030
++#define ENET_FLUSH 0x034
++#define ENET_FLUSH_RXFIFO_FLUSH 0x00000001
++#define ENET_FLUSH_TXFIFO_FLUSH 0x00000002
++#define ENET_RSV_SELECT 0x038
++#define ENET_BP_FORCE 0x03c
++#define ENET_BP_FORCE_FORCE 0x00000001
++#define ENET_DMA_RX_OK_TO_SEND_COUNT 0x040
++#define ENET_DMA_RX_OK_TO_SEND_COUNT_VAL 0x0000000f
++#define ENET_TX_CRC_CTRL 0x044
++#define ENET_MIB 0x200
++#define ENET_UNIMAC 0x400
++#define ENET_DMA 0x800
++#define ENET_DMA_CONTROLLER_CFG 0x800
++#define ENET_DMA_CTRL_CFG_MASTER_EN 0x00000001
++#define ENET_DMA_CTRL_CFG_FLOWC_CH1_EN 0x00000002
++#define ENET_DMA_CTRL_CFG_FLOWC_CH3_EN 0x00000004
++#define ENET_DMA_FLOWCTL_CH1_THRESH_LO 0x804
++#define ENET_DMA_FLOWCTL_CH1_THRESH_HI 0x808
++#define ENET_DMA_FLOWCTL_CH1_ALLOC 0x80c
++#define ENET_DMA_FLOWCTL_CH1_ALLOC_FORCE 0x80000000
++#define ENET_DMA_FLOWCTL_CH3_THRESH_LO 0x810
++#define ENET_DMA_FLOWCTL_CH3_THRESH_HI 0x814
++#define ENET_DMA_FLOWCTL_CH3_ALLOC 0x818
++#define ENET_DMA_FLOWCTL_CH5_THRESH_LO 0x81C
++#define ENET_DMA_FLOWCTL_CH5_THRESH_HI 0x820
++#define ENET_DMA_FLOWCTL_CH5_ALLOC 0x824
++#define ENET_DMA_FLOWCTL_CH7_THRESH_LO 0x828
++#define ENET_DMA_FLOWCTL_CH7_THRESH_HI 0x82C
++#define ENET_DMA_FLOWCTL_CH7_ALLOC 0x830
++#define ENET_DMA_CTRL_CHANNEL_RESET 0x834
++#define ENET_DMA_CTRL_CHANNEL_DEBUG 0x838
++#define ENET_DMA_CTRL_GLOBAL_INTERRUPT_STATUS 0x840
++#define ENET_DMA_CTRL_GLOBAL_INTERRUPT_MASK 0x844
++#define ENET_DMA_CH0_CFG 0xa00 /* RX */
++#define ENET_DMA_CH1_CFG 0xa10 /* TX */
++#define ENET_DMA_CH0_STATE_RAM 0xc00 /* RX */
++#define ENET_DMA_CH1_STATE_RAM 0xc10 /* TX */
++
++#define ENET_DMA_CH_CFG 0x00 /* assorted configuration */
++#define ENET_DMA_CH_CFG_ENABLE 0x00000001 /* set to enable channel */
++#define ENET_DMA_CH_CFG_PKT_HALT 0x00000002 /* idle after an EOP flag is detected */
++#define ENET_DMA_CH_CFG_BURST_HALT 0x00000004 /* idle after finish current memory burst */
++#define ENET_DMA_CH_CFG_INT_STAT 0x04 /* interrupts control and status */
++#define ENET_DMA_CH_CFG_INT_MASK 0x08 /* interrupts mask */
++#define ENET_DMA_CH_CFG_INT_BUFF_DONE 0x00000001 /* buffer done */
++#define ENET_DMA_CH_CFG_INT_DONE 0x00000002 /* packet xfer complete */
++#define ENET_DMA_CH_CFG_INT_NO_DESC 0x00000004 /* no valid descriptors */
++#define ENET_DMA_CH_CFG_INT_RX_ERROR 0x00000008 /* rxdma detect client protocol error */
++#define ENET_DMA_CH_CFG_MAX_BURST 0x0c /* max burst length permitted */
++#define ENET_DMA_CH_CFG_MAX_BURST_DESCSIZE_SEL 0x00040000 /* DMA Descriptor Size Selection */
++#define ENET_DMA_CH_CFG_SIZE 0x10
++
++#define ENET_DMA_CH_STATE_RAM_BASE_DESC_PTR 0x00 /* descriptor ring start address */
++#define ENET_DMA_CH_STATE_RAM_STATE_DATA 0x04 /* state/bytes done/ring offset */
++#define ENET_DMA_CH_STATE_RAM_DESC_LEN_STATUS 0x08 /* buffer descriptor status and len */
++#define ENET_DMA_CH_STATE_RAM_DESC_BASE_BUFPTR 0x0c /* buffer descrpitor current processing */
++#define ENET_DMA_CH_STATE_RAM_SIZE 0x10
++
++#define DMA_CTL_STATUS_APPEND_CRC 0x00000100
++#define DMA_CTL_STATUS_APPEND_BRCM_TAG 0x00000200
++#define DMA_CTL_STATUS_PRIO 0x00000C00 /* Prio for Tx */
++#define DMA_CTL_STATUS_WRAP 0x00001000 /* */
++#define DMA_CTL_STATUS_SOP 0x00002000 /* first buffer in packet */
++#define DMA_CTL_STATUS_EOP 0x00004000 /* last buffer in packet */
++#define DMA_CTL_STATUS_OWN 0x00008000 /* cleared by DMA, set by SW */
++#define DMA_CTL_LEN_DESC_BUFLENGTH 0x0fff0000
++#define DMA_CTL_LEN_DESC_BUFLENGTH_SHIFT 16
++#define DMA_CTL_LEN_DESC_MULTICAST 0x40000000
++#define DMA_CTL_LEN_DESC_USEFPM 0x80000000
++
++#endif
diff --git a/target/linux/bcm4908/patches-5.4/302-arm64-dts-broadcom-bcm4908-describe-Ethernet-control.patch b/target/linux/bcm4908/patches-5.4/302-arm64-dts-broadcom-bcm4908-describe-Ethernet-control.patch
new file mode 100644
index 0000000000..755292dacf
--- /dev/null
+++ b/target/linux/bcm4908/patches-5.4/302-arm64-dts-broadcom-bcm4908-describe-Ethernet-control.patch
@@ -0,0 +1,49 @@
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal at milecki.pl>
+Date: Mon, 8 Feb 2021 09:11:36 +0100
+Subject: [PATCH] arm64: dts: broadcom: bcm4908: describe Ethernet controller
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+BCM4908 SoCs have an integrated Ethernet controller.
+
+Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
+---
+
+--- a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts
++++ b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts
+@@ -87,6 +87,17 @@
+ full-duplex;
+ };
+ };
++
++ port at 8 {
++ reg = <8>;
++ phy-mode = "internal";
++ brcm,use-bcm-hdr;
++ ethernet = <&gmac>;
++ fixed-link {
++ speed = <1000>;
++ full-duplex;
++ };
++ };
+ };
+
+ &mdio {
+--- a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi
++++ b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi
+@@ -112,6 +112,14 @@
+ #size-cells = <1>;
+ ranges = <0x00 0x00 0x80000000 0x281000>;
+
++ gmac: ethernet at 2000 {
++ compatible = "brcm,bcm4908enet";
++ reg = <0x2000 0x1000>;
++
++ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
++ interrupt-names = "rx";
++ };
++
+ usb_phy: usb-phy at c200 {
+ compatible = "brcm,bcm4908-usb-phy";
+ reg = <0xc200 0x100>;
More information about the lede-commits
mailing list