[openwrt/openwrt] ipq40xx: add support for GL.iNet GL-B2200
LEDE Commits
lede-commits at lists.infradead.org
Thu Dec 2 12:43:52 PST 2021
dangole pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/febc2b831f633d8d6648267952bd43c35689c36f
commit febc2b831f633d8d6648267952bd43c35689c36f
Author: TruongSinh Tran-Nguyen <i at truongsinh.pro>
AuthorDate: Wed Dec 1 16:18:17 2021 +0100
ipq40xx: add support for GL.iNet GL-B2200
This patch adds supports for the GL-B2200 router.
Specifications:
- SOC: Qualcomm IPQ4019 ARM Quad-Core
- RAM: 512 MiB
- Flash: 16 MiB NOR - SPI0
- EMMC: 8GB EMMC
- ETH: Qualcomm QCA8075
- WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2
- WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2
- WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2
- INPUT: Reset, WPS
- LED: Power, Internet
- UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
- UART2: On board with BLE module
- SPI1: On board socket for Zigbee module
Update firmware instructions:
Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at
https://docs.gl-inet.com/en/3/troubleshooting/debrick/).
Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware.
Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first.
What's working:
- WiFi 2G, 5G
- WPA2/WPA3
Not tested:
- Bluetooth LE/Zigbee
Credits goes to the original authors of this patch.
V1->V2:
- updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake)
- add uboot-envtools support
V2->V3:
- Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface
V3->V4:
- wire up sysupgrade
Signed-off-by: Li Zhang <li.zhang at gl-inet.com>
[fix tab and trailing space, document what's working and what's not]
Signed-off-by: TruongSinh Tran-Nguyen <i at truongsinh.pro>
[rebase on top of master, address remaining comments]
Signed-off-by: Enrico Mioso <mrkiko.rs at gmail.com>
[remove redundant check in platform.sh]
Signed-off-by: Daniel Golle <daniel at makrotopia.org>
---
package/boot/uboot-envtools/files/ipq40xx | 1 +
package/firmware/ipq-wifi/Makefile | 2 +
.../ipq-wifi/board-glinet_gl-b2200.qca4019 | Bin 0 -> 24308 bytes
.../ipq-wifi/board-glinet_gl-b2200.qca9888 | Bin 0 -> 12200 bytes
.../ipq40xx/base-files/etc/board.d/02_network | 5 +
.../etc/hotplug.d/firmware/11-ath10k-caldata | 5 +
.../ipq40xx/base-files/lib/upgrade/platform.sh | 15 +
.../arch/arm/boot/dts/qcom-ipq4019-gl-b2200.dts | 364 +++++++++++++++++++++
target/linux/ipq40xx/generic/target.mk | 1 +
target/linux/ipq40xx/image/generic.mk | 28 ++
.../patches-5.10/901-arm-boot-add-dts-files.patch | 3 +-
.../patches-5.4/901-arm-boot-add-dts-files.patch | 3 +-
12 files changed, 425 insertions(+), 2 deletions(-)
diff --git a/package/boot/uboot-envtools/files/ipq40xx b/package/boot/uboot-envtools/files/ipq40xx
index 1462aa991d..9a71a622f7 100644
--- a/package/boot/uboot-envtools/files/ipq40xx
+++ b/package/boot/uboot-envtools/files/ipq40xx
@@ -35,6 +35,7 @@ devolo,magic-2-wifi-next|\
edgecore,ecw5211|\
glinet,gl-ap1300|\
glinet,gl-b1300|\
+glinet,gl-b2200|\
luma,wrtq-329acn|\
netgear,wac510|\
openmesh,a42|\
diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile
index ebaac48c24..b1e6541e61 100644
--- a/package/firmware/ipq-wifi/Makefile
+++ b/package/firmware/ipq-wifi/Makefile
@@ -39,6 +39,7 @@ ALLWIFIBOARDS:= \
engenius_emr3500 \
ezviz_cs-w3-wd1200g-eup \
glinet_gl-ap1300 \
+ glinet_gl-b2200 \
glinet_gl-s1300 \
linksys_ea8300 \
linksys_mr8300-v0 \
@@ -127,6 +128,7 @@ $(eval $(call generate-ipq-wifi-package,engenius_emd1,EnGenius EMD1))
$(eval $(call generate-ipq-wifi-package,engenius_emr3500,EnGenius EMR3500))
$(eval $(call generate-ipq-wifi-package,ezviz_cs-w3-wd1200g-eup,EZVIZ CS-W3-WD1200G EUP))
$(eval $(call generate-ipq-wifi-package,glinet_gl-ap1300,GL.iNet GL-AP1300))
+$(eval $(call generate-ipq-wifi-package,glinet_gl-b2200,GL.iNet GL-B2200))
$(eval $(call generate-ipq-wifi-package,glinet_gl-s1300,GL.iNet GL-S1300))
$(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300))
$(eval $(call generate-ipq-wifi-package,linksys_mr8300-v0,Linksys MR8300))
diff --git a/package/firmware/ipq-wifi/board-glinet_gl-b2200.qca4019 b/package/firmware/ipq-wifi/board-glinet_gl-b2200.qca4019
new file mode 100644
index 0000000000..ac1850160a
Binary files /dev/null and b/package/firmware/ipq-wifi/board-glinet_gl-b2200.qca4019 differ
diff --git a/package/firmware/ipq-wifi/board-glinet_gl-b2200.qca9888 b/package/firmware/ipq-wifi/board-glinet_gl-b2200.qca9888
new file mode 100644
index 0000000000..4f0a521f35
Binary files /dev/null and b/package/firmware/ipq-wifi/board-glinet_gl-b2200.qca9888 differ
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 63209fa49a..c37fc58b22 100644
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -106,6 +106,11 @@ ipq40xx_setup_interfaces()
ucidef_add_switch "switch0" \
"0u at eth0" "3:lan" "4:lan"
;;
+ glinet,gl-b2200)
+ ucidef_set_interfaces_lan_wan "eth0" "eth1"
+ ucidef_add_switch "switch0" \
+ "0u at eth0" "1:lan" "2:lan" "3:lan" "5:lan" "0u at eth1" "4:wan"
+ ;;
mobipromo,cm520-79f)
ucidef_add_switch "switch0" \
"0u at eth0" "3:lan:2" "4:lan:1"
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index f43a3a88b7..8924fb3258 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -9,6 +9,9 @@ board=$(board_name)
case "$FIRMWARE" in
"ath10k/cal-pci-0000:01:00.0.bin")
case "$board" in
+ glinet,gl-b2200)
+ caldata_extract "ART" 0x9000 0x2f20
+ ;;
meraki,mr33)
caldata_extract_ubi "ART" 0x9000 0x844
caldata_valid "4408" || caldata_extract "ART" 0x9000 0x844
@@ -64,6 +67,7 @@ case "$FIRMWARE" in
ezviz,cs-w3-wd1200g-eup |\
glinet,gl-ap1300 |\
glinet,gl-b1300 |\
+ glinet,gl-b2200 |\
glinet,gl-s1300 |\
linksys,ea6350v3 |\
mobipromo,cm520-79f |\
@@ -186,6 +190,7 @@ case "$FIRMWARE" in
ezviz,cs-w3-wd1200g-eup |\
glinet,gl-ap1300 |\
glinet,gl-b1300 |\
+ glinet,gl-b2200 |\
glinet,gl-s1300 |\
linksys,ea6350v3 |\
mobipromo,cm520-79f |\
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
index 8f8494dcff..357e02000a 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
@@ -96,6 +96,12 @@ platform_do_upgrade() {
qxwlan,e2600ac-c2)
nand_do_upgrade "$1"
;;
+ glinet,gl-b2200)
+ CI_KERNPART="0:HLOS"
+ CI_ROOTPART="rootfs"
+ CI_DATAPART="rootfs_data"
+ emmc_do_upgrade "$1"
+ ;;
alfa-network,ap120c-ac)
part="$(awk -F 'ubi.mtd=' '{printf $2}' /proc/cmdline | sed -e 's/ .*$//')"
if [ "$part" = "rootfs1" ]; then
@@ -166,3 +172,12 @@ platform_do_upgrade() {
;;
esac
}
+
+platform_copy_config() {
+ case "$(board_name)" in
+ glinet,gl-b2200)
+ emmc_copy_config
+ ;;
+ esac
+ return 0;
+}
diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-gl-b2200.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-gl-b2200.dts
new file mode 100644
index 0000000000..6b84f78dc4
--- /dev/null
+++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-gl-b2200.dts
@@ -0,0 +1,364 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "GL.iNet GL-B2200";
+ compatible = "glinet,gl-b2200", "qcom,ipq4019";
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>;
+ };
+
+ chosen {
+ bootargs-append = " root=/dev/mmcblk0p2 rw rootwait clk_ignore_unused";
+ };
+
+ soc {
+ rng at 22000 {
+ status = "okay";
+ };
+
+ mdio at 90000 {
+ status = "okay";
+ };
+
+ ess-psgmii at 98000 {
+ status = "okay";
+ };
+
+ tcsr at 1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr at 194b000 {
+ /* select hostmode */
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ status = "okay";
+ };
+
+ ess_tcsr at 1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr at 1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ crypto at 8e3a000 {
+ status = "okay";
+ };
+
+ ess-switch at c000000 {
+ status = "okay";
+ switch_lan_bmp = <0x2e>;
+ switch_wan_bmp = <0x10>;
+ };
+
+ edma at c080000 {
+ status = "okay";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ wps {
+ label = "wps";
+ gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ linux,input-type = <1>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ linux,input-type = <1>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ power_blue {
+ label = "blue:power";
+ gpios = <&tlmm 57 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ internet_blue {
+ label = "blue:internet";
+ gpios = <&tlmm 60 GPIO_ACTIVE_HIGH>;
+ };
+ power_white {
+ label = "white:power";
+ gpios = <&tlmm 61 GPIO_ACTIVE_LOW>;
+ };
+ internet_white {
+ label = "white:internet";
+ gpios = <&tlmm 66 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&gmac1 {
+ qcom,phy_mdio_addr = <3>;
+ qcom,poll_required = <1>;
+ qcom,forced_speed = <1000>;
+ qcom,forced_duplex = <1>;
+ vlan_tag = <2 0x10>;
+};
+
+&gmac0 {
+ vlan_tag = <1 0x2e>;
+};
+
+&vqmmc {
+ status = "okay";
+};
+
+&sdhci {
+ status = "okay";
+ pinctrl-0 = <&sd_pins>;
+ pinctrl-names = "default";
+ cd-gpios = <&tlmm 3 GPIO_ACTIVE_LOW>;
+ vqmmc-supply = <&vqmmc>;
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "SBL1";
+ reg = <0x0 0x40000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "MIBIB";
+ reg = <0x40000 0x20000>;
+ read-only;
+ };
+
+ partition at 60000 {
+ label = "QSEE";
+ reg = <0x60000 0x60000>;
+ read-only;
+ };
+
+ partition at c0000 {
+ label = "CDT";
+ reg = <0xc0000 0x10000>;
+ read-only;
+ };
+
+ partition at d0000 {
+ label = "DDRPARAMS";
+ reg = <0xd0000 0x10000>;
+ read-only;
+ };
+
+ partition at e0000 {
+ label = "APPSBLENV";
+ reg = <0xe0000 0x10000>;
+ read-only;
+ };
+
+ partition at f0000 {
+ label = "APPSBL";
+ reg = <0xf0000 0x80000>;
+ read-only;
+ };
+
+ partition at 170000 {
+ label = "ART";
+ reg = <0x170000 0x10000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&blsp1_spi2 {
+ pinctrl-0 = <&spi_1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ spidev1: spi at 0 {
+ compatible = "siliconlabs,si3210";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&blsp1_uart2 {
+ pinctrl-0 = <&serial_1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&tlmm {
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ serial_1_pins: serial1_pinmux {
+ mux {
+ pins = "gpio8", "gpio9",
+ "gpio10", "gpio11";
+ function = "blsp_uart1";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pinmux {
+ function = "blsp_spi0";
+ pins = "gpio13", "gpio14", "gpio15";
+ };
+ pinmux_cs {
+ function = "gpio";
+ pins = "gpio12";
+ };
+ pinconf {
+ pins = "gpio13", "gpio14", "gpio15";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pinconf_cs {
+ pins = "gpio12";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ spi_1_pins: spi_1_pinmux {
+ mux {
+ pins = "gpio44", "gpio46", "gpio47";
+ function = "blsp_spi1";
+ bias-disable;
+ };
+ cs {
+ pins = "gpio45";
+ function = "gpio";
+ bias-pull-up;
+ };
+ reset {
+ pins = "gpio43";
+ function = "gpio";
+ output-high;
+ };
+ mux_2 {
+ pins = "gpio35";
+ function = "gpio";
+ output-high;
+ };
+ host_int {
+ pins = "gpio2";
+ function = "gpio";
+ input;
+ };
+ wake {
+ pins = "gpio48";
+ function = "gpio";
+ output-high;
+ };
+ };
+
+ sd_pins: sd_pins {
+ pinmux {
+ function = "sdio";
+ pins = "gpio23", "gpio24", "gpio25", "gpio26",
+ "gpio29", "gpio30", "gpio31", "gpio32";
+ drive-strength = <10>;
+ };
+
+ pinmux_sd_clk {
+ function = "sdio";
+ pins = "gpio27";
+ drive-strength = <16>;
+ };
+
+ pinmux_sd7 {
+ function = "sdio";
+ pins = "gpio28";
+ drive-strength = <10>;
+ bias-disable;
+ };
+ };
+
+};
+
+&pcie0 {
+ status = "okay";
+ perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+ wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+
+ bridge at 0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi2: wifi at 1,0 {
+ status = "okay";
+ compatible = "qcom,ath10k";
+ reg = <0x00010000 0 0 0 0>;
+ qcom,ath10k-calibration-variant = "GL-B2200";
+ };
+ };
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "GL-B2200";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "GL-B2200";
+};
diff --git a/target/linux/ipq40xx/generic/target.mk b/target/linux/ipq40xx/generic/target.mk
index f5cb1fb19b..e158b1c98b 100644
--- a/target/linux/ipq40xx/generic/target.mk
+++ b/target/linux/ipq40xx/generic/target.mk
@@ -1 +1,2 @@
BOARDNAME:=Generic
+FEATURES+=emmc
diff --git a/target/linux/ipq40xx/image/generic.mk b/target/linux/ipq40xx/image/generic.mk
index 0d7d7a30d2..872c4f957f 100644
--- a/target/linux/ipq40xx/image/generic.mk
+++ b/target/linux/ipq40xx/image/generic.mk
@@ -92,6 +92,16 @@ define Build/qsdk-ipq-factory-nand-askey
@mv $@.new $@
endef
+define Build/qsdk-ipq-app-gpt
+ cp $@ $@.tmp 2>/dev/null || true
+ ptgen -g -o $@.tmp -a 1 -l 1024 \
+ -t 0x2e -N 0:HLOS -r -p 32M \
+ -t 0x83 -N rootfs -r -p 128M \
+ -N rootfs_data -p 512M
+ cat $@.tmp >> $@
+ rm $@.tmp
+endef
+
define Build/SenaoFW
-$(STAGING_DIR_HOST)/bin/mksenaofw \
-n $(BOARD_NAME) -r $(VENDOR_ID) -p $(1) \
@@ -520,6 +530,24 @@ define Device/glinet_gl-b1300
endef
TARGET_DEVICES += glinet_gl-b1300
+define Device/glinet_gl-b2200
+ $(call Device/FitzImage)
+ DEVICE_VENDOR := GL.iNet
+ DEVICE_MODEL := GL-B2200
+ SOC := qcom-ipq4019
+ DEVICE_DTS_CONFIG := config at ap.dk04.1-c3
+ KERNEL_INITRAMFS_SUFFIX := -recovery.itb
+ IMAGES := emmc.img.gz sysupgrade.bin
+ IMAGE/emmc.img.gz := qsdk-ipq-app-gpt |\
+ pad-to 1024k | append-kernel |\
+ pad-to 33792k | append-rootfs |\
+ append-metadata | gzip
+ IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+ DEVICE_PACKAGES := ath10k-firmware-qca9888-ct ipq-wifi-glinet_gl-b2200 \
+ kmod-fs-ext4 kmod-mmc kmod-spi-dev mkf2fs e2fsprogs kmod-fs-f2fs
+endef
+TARGET_DEVICES += glinet_gl-b2200
+
define Device/glinet_gl-s1300
$(call Device/FitzImage)
DEVICE_VENDOR := GL.iNet
diff --git a/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch
index 3bd13bf932..b641251423 100644
--- a/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john at phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -902,11 +902,70 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -902,11 +902,71 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
@@ -76,6 +76,7 @@ Signed-off-by: John Crispin <john at phrozen.org>
+ qcom-ipq4029-ap-303h.dtb \
+ qcom-ipq4029-ap-365.dtb \
+ qcom-ipq4029-gl-b1300.dtb \
++ qcom-ipq4019-gl-b2200.dtb \
+ qcom-ipq4029-gl-s1300.dtb \
+ qcom-ipq4029-mr33.dtb \
qcom-ipq8064-ap148.dtb \
diff --git a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
index 734d08387a..4270418d6c 100644
--- a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john at phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -837,11 +837,68 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -837,11 +837,69 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
@@ -74,6 +74,7 @@ Signed-off-by: John Crispin <john at phrozen.org>
+ qcom-ipq4029-ap-303h.dtb \
+ qcom-ipq4029-ap-365.dtb \
+ qcom-ipq4029-gl-b1300.dtb \
++ qcom-ipq4019-gl-b2200.dtb \
+ qcom-ipq4029-gl-s1300.dtb \
+ qcom-ipq4029-mr33.dtb \
qcom-ipq8064-ap148.dtb \
More information about the lede-commits
mailing list