[openwrt/openwrt] ath79: add support for Samsung WAM250

Sun Sep 27 19:30:27 EDT 2020

pepe2k pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/cf42660dcedf5b994eb9aa5f508ec9a7c301fddc

commit cf42660dcedf5b994eb9aa5f508ec9a7c301fddc
Author: Piotr Dymacz <pepe2k at gmail.com>
AuthorDate: Fri Sep 18 14:11:13 2020 +0200

    ath79: add support for Samsung WAM250
    
    Samsung WAM250 is a dual-band (selectable, not simultaneous) wireless
    hub, dedicated for Samsung Shape Wireless Audio System. The device is
    based on Atheros AR9344 (FCC ID: A3LWAM250). Support for this device
    was first introduced in e58e49bdbe (ar71xx target).
    
    Specifications:
    
    - Atheros AR9344
    - 560/450/225 MHz (CPU/DDR/AHB)
    - 64 MB of RAM (DDR2)
    - 16 MB of flash (SPI NOR)
    - 2x 10/100 Mbps Ethernet
    - 2T2R 2.4/5 GHz Wi-Fi, with ext. PA (SE2598L, SE5003L) and LNA
    - 1x USB 2.0
    - 4x LED (all are driven by GPIO)
    - 2x button (reset, wps/speaker add)
    - DC jack for main power input (14 V)
    - UART header on PCB (J4, RX: 3, TX: 5)
    
    Flash instruction:
    
    This device uses dual-image (switched between upgrades) with a common
    jffs2 config partition. Fortunately, there is a way to disable this mode
    so that more flash space can be used by OpenWrt image.
    
    You can easily access this device over telnet, using root/root
    credentials (the same also work for serial console access).
    
    1. Make sure that your device uses second (bootpart=2) image using
       command: "fw_printenv bootpart".
    2. If your device uses first image (bootpart=1), perform upgrade to the
       latest vendor firmware (after the update, device should boot from
       second partition) using web gui (default login: admin/1234567890).
    3. Rename "sysupgrade" image to "firmware.bin", download it (you can use
       wget, tftp or ftpget) to "/tmp" and issue below commands:
    
       mtd_debug erase /dev/mtd3 0 $(wc -c /tmp/firmware.bin | awk -F' ' '{print $1}')
       mtd_debug write /dev/mtd3 0 $(wc -c /tmp/firmware.bin)
       fw_setenv bootpart
       fw_setenv bootcmd "bootm 0x9f070000"
       reboot
    
    Revert to vendor firmware instruction:
    
    1. Download vendor firmware to "/tmp" device and issue below commands:
    
       fw_setenv bootpart 1
       sysupgrade -n -F SS_BHUB_v2.2.05.bin
    
    Signed-off-by: Piotr Dymacz <pepe2k at gmail.com>
---
 target/linux/ath79/dts/ar9344_samsung_wam250.dts   | 163 +++++++++++++++++++++
 .../ath79/generic/base-files/etc/board.d/01_leds   |   3 +
 target/linux/ath79/image/generic.mk                |  10 ++
 3 files changed, 176 insertions(+)

diff --git a/target/linux/ath79/dts/ar9344_samsung_wam250.dts b/target/linux/ath79/dts/ar9344_samsung_wam250.dts
new file mode 100644
index 0000000000..3ae68d6104
--- /dev/null
+++ b/target/linux/ath79/dts/ar9344_samsung_wam250.dts
@@ -0,0 +1,163 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "ar9344.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Samsung WAM250";
+	compatible = "samsung,wam250", "qca,ar9344";
+
+	aliases {
+		led-boot = &led_power;
+		led-failsafe = &led_power;
+		led-running = &led_power;
+		led-upgrade = &led_power;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+
+		wps {
+			label = "wps";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		lan {
+			label = "wam250:white:lan";
+			gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+		};
+
+		led_power: power {
+			label = "wam250:white:power";
+			gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+		};
+
+		repeater {
+			label = "wam250:white:repeater";
+			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+		};
+
+		wlan {
+			label = "wam250:white:wlan";
+			gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	phy-handle = <&swphy0>;
+
+	mtd-mac-address = <&art 0x1002>;
+	mtd-mac-address-increment = <1>;
+
+	gmac-config {
+		device = <&gmac>;
+		switch-phy-swap = <1>;
+	};
+};
+
+&eth1 {
+	status = "okay";
+
+	mtd-mac-address = <&art 0x1002>;
+};
+
+&gpio {
+	lna0 {
+		line-name = "wam250:ext:lna0";
+		gpios = <19 GPIO_ACTIVE_HIGH>;
+		output-high;
+		gpio-hog;
+	};
+};
+
+&ref {
+	clock-frequency = <40000000>;
+};
+
+&spi {
+	status = "okay";
+
+	num-cs = <1>;
+
+	flash at 0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		m25p,fast-read;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition at 0 {
+				label = "u-boot";
+				reg = <0x000000 0x040000>;
+				read-only;
+			};
+
+			partition at 40000 {
+				label = "u-boot-env";
+				reg = <0x040000 0x010000>;
+			};
+
+			partition at 50000 {
+				label = "nvram";
+				reg = <0x050000 0x020000>;
+				read-only;
+			};
+
+			partition at 70000 {
+				compatible = "denx,uimage";
+				label = "firmware";
+				reg = <0x070000 0xf80000>;
+			};
+
+			art: partition at ff0000 {
+				label = "art";
+				reg = <0xff0000 0x010000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&uart {
+	status = "okay";
+};
+
+
+&usb {
+	status = "okay";
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+
+&wmac {
+	status = "okay";
+
+	mtd-cal-data = <&art 0x1000>;
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index 2b7b3bed55..78726afecf 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -212,6 +212,9 @@ pcs,cr3000)
 qihoo,c301)
 	ucidef_set_led_wlan "wlan" "WLAN" "$boardname:green:wlan" "phy0tpt"
 	;;
+samsung,wam250)
+	ucidef_set_led_netdev "lan" "LAN" "$boardname:white:lan" "eth0"
+	;;
 tplink,archer-a7-v5|\
 tplink,archer-c7-v4|\
 tplink,archer-c7-v5)
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index 5d1058cae2..ce927ecd4f 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -1415,6 +1415,16 @@ define Device/rosinson_wr818
 endef
 TARGET_DEVICES += rosinson_wr818
 
+define Device/samsung_wam250
+  SOC := ar9344
+  DEVICE_VENDOR := Samsung
+  DEVICE_MODEL := WAM250
+  IMAGE_SIZE := 15872k
+  DEVICE_PACKAGES := kmod-usb2
+  SUPPORTED_DEVICES += wam250
+endef
+TARGET_DEVICES += samsung_wam250
+
 define Device/siemens_ws-ap3610
   SOC := ar7161
   DEVICE_VENDOR := Siemens

