[openwrt/openwrt] rtl838x: add new architecture
LEDE Commits
lede-commits at lists.infradead.org
Mon Sep 14 02:49:21 EDT 2020
blogic pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/df8e6be59a1fbce3f8c6878fe7440a129b1245d6
commit df8e6be59a1fbce3f8c6878fe7440a129b1245d6
Author: Birger Koblitz <git at birger-koblitz.de>
AuthorDate: Sun Sep 13 09:06:13 2020 +0200
rtl838x: add new architecture
This adds support for the RTL838x Architecture.
SoCs of this type are used in managed and un-managed Switches and Routers
with 8-28 ports. Drivers are provided for SoC initialization, GPIOs, Flash,
Ethernet including a DSA switch driver and internal and external PHYs used
with these switches.
Supported SoCs:
RTL8380M
RTL8381M
RTL8382M
The kernel will also boot on the following RTL839x SoCs, however driver
support apart from spi-nor is missing:
RTL8390
RTL8391
RTL8393
The following PHYs are supported:
RTL8214FC (Quad QSGMII multiplexing GMAC and SFP port)
RTL8218B internal: internal PHY of the RTL838x chips
RTL8318b external (QSGMII 8-port GMAC phy)
RTL8382M SerDes for 2 SFP ports
Initialization sequences for the PHYs are provided in the form of
firmware files.
Flash driver supports 3 / 4 byte access
DSA switch driver supports VLANs, port isolation, STP and port mirroring.
The ALLNET ALL-SG8208M is supported as Proof of Concept:
RTL8382M SoC
1 MIPS 4KEc core @ 500MHz
8 Internal PHYs (RTL8218B)
128MB DRAM (Nanya NT5TU128MB)
16MB NOR Flash (MXIC 25L128)
8 GBEthernet ports with one green status LED each (SoC controlled)
1 Power LED (not configurable)
1 SYS LED (configurable)
1 On-Off switch (not configurable)
1 Reset button at the right behind right air-vent (not configurable)
1 Reset button on front panel (configurable)
12V 1A barrel connector
1 serial header with populated standard pin connector and with markings
GND TX RX Vcc(3.3V), connection properties: 115200 8N1
To install, upload the sysupgrade image to the OEM webpage.
Signed-off-by: Birger Koblitz <git at birger-koblitz.de>
---
target/linux/rtl838x/Makefile | 22 +
.../linux/rtl838x/base-files/etc/board.d/01_leds | 15 +
.../rtl838x/base-files/etc/board.d/02_network | 87 +
target/linux/rtl838x/base-files/etc/inittab | 3 +
.../lib/firmware/rtl838x_phy/rtl838x_8214fc.fw | Bin 0 -> 1676 bytes
.../lib/firmware/rtl838x_phy/rtl838x_8218b.fw | Bin 0 -> 1168 bytes
.../lib/firmware/rtl838x_phy/rtl838x_8380.fw | Bin 0 -> 1184 bytes
.../rtl838x/base-files/lib/upgrade/platform.sh | 19 +
target/linux/rtl838x/config-5.4 | 226 ++
.../rtl838x/dts/rtl8382_allnet_all-sg8208m.dts | 221 ++
target/linux/rtl838x/dts/rtl838x.dtsi | 110 +
.../arch/mips/include/asm/mach-rtl838x/ioremap.h | 34 +
.../arch/mips/include/asm/mach-rtl838x/irq.h | 10 +
.../mips/include/asm/mach-rtl838x/mach-rtl838x.h | 428 ++++
.../rtl838x/files-5.4/arch/mips/rtl838x/Makefile | 5 +
.../rtl838x/files-5.4/arch/mips/rtl838x/Platform | 6 +
.../rtl838x/files-5.4/arch/mips/rtl838x/irq.c | 263 +++
.../rtl838x/files-5.4/arch/mips/rtl838x/prom.c | 174 ++
.../rtl838x/files-5.4/arch/mips/rtl838x/serial.c | 100 +
.../rtl838x/files-5.4/arch/mips/rtl838x/setup.c | 187 ++
.../rtl838x/files-5.4/drivers/gpio/gpio-rtl838x.c | 807 ++++++++
.../files-5.4/drivers/mtd/spi-nor/rtl838x-nor.c | 607 ++++++
.../files-5.4/drivers/mtd/spi-nor/rtl838x-spi.h | 111 +
.../rtl838x/files-5.4/drivers/net/dsa/rtl838x.h | 188 ++
.../files-5.4/drivers/net/dsa/rtl838x_phy.c | 1286 ++++++++++++
.../rtl838x/files-5.4/drivers/net/dsa/rtl838x_sw.c | 2150 ++++++++++++++++++++
.../files-5.4/drivers/net/ethernet/rtl838x_eth.c | 1205 +++++++++++
.../files-5.4/drivers/net/ethernet/rtl838x_eth.h | 261 +++
target/linux/rtl838x/image/Makefile | 44 +
.../300-mips-add-rtl838x-platform.patch | 42 +
.../patches-5.4/301-gpio-add-rtl838x-driver.patch | 25 +
.../400-mtd-add-rtl838x-spi-flash-driver.patch | 23 +
...00-net-dsa-add-support-for-rtl838x-switch.patch | 26 +
...t-dsa-add-rtl838x-support-for-tag-trailer.patch | 37 +
...et-dsa-increase-dsa-max-ports-for-rtl838x.patch | 13 +
...ethernet-add-support-for-rtl838x-ethernet.patch | 26 +
...703-include-linux-add-phy-ops-for-rtl838x.patch | 13 +
...4-drivers-net-phy-eee-support-for-rtl838x.patch | 41 +
target/linux/rtl838x/profiles/00-default.mk | 13 +
39 files changed, 8828 insertions(+)
diff --git a/target/linux/rtl838x/Makefile b/target/linux/rtl838x/Makefile
new file mode 100644
index 0000000000..764b94ae38
--- /dev/null
+++ b/target/linux/rtl838x/Makefile
@@ -0,0 +1,22 @@
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+include $(TOPDIR)/rules.mk
+
+ARCH:=mips
+CPU_TYPE:=4kec
+BOARD:=rtl838x
+BOARDNAME:=Realtek MIPS
+FEATURES:=ramdisk squashfs
+
+KERNEL_PATCHVER:=5.4
+
+define Target/Description
+ Build firmware images for Realtek RTL838x based boards.
+endef
+
+include $(INCLUDE_DIR)/target.mk
+
+DEFAULT_PACKAGES += swconfig uboot-envtools ethtool kmod-gpio-button-hotplug
+
+$(eval $(call BuildTarget))
diff --git a/target/linux/rtl838x/base-files/etc/board.d/01_leds b/target/linux/rtl838x/base-files/etc/board.d/01_leds
new file mode 100755
index 0000000000..7991b832f6
--- /dev/null
+++ b/target/linux/rtl838x/base-files/etc/board.d/01_leds
@@ -0,0 +1,15 @@
+#!/bin/sh
+
+. /lib/functions/uci-defaults.sh
+
+board=$(board_name)
+boardname="${board##*,}"
+
+board_config_update
+
+case $board in
+esac
+
+board_config_flush
+
+exit 0
diff --git a/target/linux/rtl838x/base-files/etc/board.d/02_network b/target/linux/rtl838x/base-files/etc/board.d/02_network
new file mode 100755
index 0000000000..a79869d8c3
--- /dev/null
+++ b/target/linux/rtl838x/base-files/etc/board.d/02_network
@@ -0,0 +1,87 @@
+#!/bin/sh
+
+. /lib/functions.sh
+. /lib/functions/uci-defaults.sh
+. /lib/functions/system.sh
+
+rtl838x_setup_switch()
+{
+ local switchid net portid master device lan_role lan_list
+
+ json_select_object switch
+ # Find slave ports
+ for net in $(ls -d /sys/class/net/*); do
+ switchid=$(cat $net/phys_switch_id 2>/dev/null)
+ [ -z "$switchid" ] && continue
+ device=$(basename $net)
+ portid=$(cat $net/phys_port_name)
+ lan_role="$lan_role ${portid##p}"
+ lan_list="$lan_list $device"
+ json_select_object "switch$((switchid))"
+ json_add_boolean enable 1
+ json_add_boolean reset 0
+ json_add_boolean dsa 1
+ json_select_array ports
+ json_add_object
+ json_add_int num "${portid##p}"
+ json_add_string role "lan"
+ json_add_string device "$device"
+ json_close_object
+ json_select ..
+ json_select ..
+ done
+ # Add switch master device
+ for net in $(ls -d /sys/class/net/*/dsa); do
+ master=$(dirname $net)
+ device=$(basename $master)
+ portid=$(cat $master/phys_port_name)
+ lan_role="$lan_role ${portid##p}"
+ json_select_object "switch$((switchid))"
+ json_select_array ports
+ json_add_object
+ json_add_int num "${portid##p}"
+ json_add_string device "$device"
+ json_add_boolean need_tag 0
+ json_add_boolean want_untag 0
+ json_add_boolean master 1
+ json_close_object
+ json_select ..
+ json_select_array roles
+ json_add_object
+ json_add_string role "lan"
+ lan_role=$(echo $lan_role | xargs -n1 | sort -n | xargs)
+ json_add_string ports "$lan_role"
+ json_close_object
+ json_select ..
+ json_select ..
+ done
+ json_select ..
+ lan_list=$(echo $lan_list | xargs -n1 | sort -V | xargs)
+ ucidef_set_interface_lan "$lan_list"
+}
+
+rtl838x_setup_macs()
+{
+ local board="$1"
+ local lan_mac
+ local wan_mac
+ local label_mac
+
+ case $board in
+ allnet,all-sg8208m)
+ lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
+ label_mac=$lan_mac
+ esac
+
+ [ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
+ [ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
+ [ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac
+}
+
+board_config_update
+board=$(board_name)
+rtl838x_setup_switch
+rtl838x_setup_macs $board
+board_config_flush
+
+exit 0
diff --git a/target/linux/rtl838x/base-files/etc/inittab b/target/linux/rtl838x/base-files/etc/inittab
new file mode 100644
index 0000000000..9820e7144b
--- /dev/null
+++ b/target/linux/rtl838x/base-files/etc/inittab
@@ -0,0 +1,3 @@
+::sysinit:/etc/init.d/rcS S boot
+::shutdown:/etc/init.d/rcS K shutdown
+::askconsole:/usr/libexec/login.sh
diff --git a/target/linux/rtl838x/base-files/lib/firmware/rtl838x_phy/rtl838x_8214fc.fw b/target/linux/rtl838x/base-files/lib/firmware/rtl838x_phy/rtl838x_8214fc.fw
new file mode 100644
index 0000000000..035c02d804
Binary files /dev/null and b/target/linux/rtl838x/base-files/lib/firmware/rtl838x_phy/rtl838x_8214fc.fw differ
diff --git a/target/linux/rtl838x/base-files/lib/firmware/rtl838x_phy/rtl838x_8218b.fw b/target/linux/rtl838x/base-files/lib/firmware/rtl838x_phy/rtl838x_8218b.fw
new file mode 100644
index 0000000000..a907849fb9
Binary files /dev/null and b/target/linux/rtl838x/base-files/lib/firmware/rtl838x_phy/rtl838x_8218b.fw differ
diff --git a/target/linux/rtl838x/base-files/lib/firmware/rtl838x_phy/rtl838x_8380.fw b/target/linux/rtl838x/base-files/lib/firmware/rtl838x_phy/rtl838x_8380.fw
new file mode 100644
index 0000000000..ef84c71753
Binary files /dev/null and b/target/linux/rtl838x/base-files/lib/firmware/rtl838x_phy/rtl838x_8380.fw differ
diff --git a/target/linux/rtl838x/base-files/lib/upgrade/platform.sh b/target/linux/rtl838x/base-files/lib/upgrade/platform.sh
new file mode 100644
index 0000000000..927aadbe31
--- /dev/null
+++ b/target/linux/rtl838x/base-files/lib/upgrade/platform.sh
@@ -0,0 +1,19 @@
+PART_NAME=firmware
+REQUIRE_IMAGE_METADATA=1
+
+RAMFS_COPY_BIN='fw_printenv fw_setenv'
+RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
+
+platform_check_image() {
+ return 0
+}
+
+platform_do_upgrade() {
+ local board=$(board_name)
+
+ case "$board" in
+ *)
+ default_do_upgrade "$1"
+ ;;
+ esac
+}
diff --git a/target/linux/rtl838x/config-5.4 b/target/linux/rtl838x/config-5.4
new file mode 100644
index 0000000000..4cd2fddba3
--- /dev/null
+++ b/target/linux/rtl838x/config-5.4
@@ -0,0 +1,226 @@
+CONFIG_ARCH_32BIT_OFF_T=y
+CONFIG_ARCH_CLOCKSOURCE_DATA=y
+CONFIG_ARCH_HAS_DMA_COHERENT_TO_PFN=y
+CONFIG_ARCH_HAS_DMA_PREP_COHERENT=y
+CONFIG_ARCH_HAS_DMA_WRITE_COMBINE=y
+CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
+CONFIG_ARCH_HAS_RESET_CONTROLLER=y
+CONFIG_ARCH_HAS_SYNC_DMA_FOR_DEVICE=y
+CONFIG_ARCH_HAS_UNCACHED_SEGMENT=y
+CONFIG_ARCH_HIBERNATION_POSSIBLE=y
+CONFIG_ARCH_MMAP_RND_BITS_MAX=15
+CONFIG_ARCH_MMAP_RND_COMPAT_BITS_MAX=15
+CONFIG_ARCH_SUPPORTS_UPROBES=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_ARCH_USE_BUILTIN_BSWAP=y
+CONFIG_ARCH_USE_MEMREMAP_PROT=y
+CONFIG_ARCH_USE_QUEUED_RWLOCKS=y
+CONFIG_ARCH_USE_QUEUED_SPINLOCKS=y
+CONFIG_ARCH_WANT_DEFAULT_TOPDOWN_MMAP_LAYOUT=y
+CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=4096
+CONFIG_CEVT_R4K=y
+CONFIG_CLKDEV_LOOKUP=y
+CONFIG_CLONE_BACKWARDS=y
+CONFIG_COMMON_CLK=y
+# CONFIG_COMMON_CLK_BOSTON is not set
+CONFIG_COMPAT_32BIT_TIME=y
+CONFIG_CONSOLE_LOGLEVEL_DEFAULT=15
+CONFIG_CPU_BIG_ENDIAN=y
+CONFIG_CPU_GENERIC_DUMP_TLB=y
+CONFIG_CPU_HAS_LOAD_STORE_LR=y
+CONFIG_CPU_HAS_PREFETCH=y
+CONFIG_CPU_HAS_RIXI=y
+CONFIG_CPU_HAS_SYNC=y
+CONFIG_CPU_MIPS32=y
+# CONFIG_CPU_MIPS32_R1 is not set
+CONFIG_CPU_MIPS32_R2=y
+CONFIG_CPU_MIPSR2=y
+CONFIG_CPU_NEEDS_NO_SMARTMIPS_OR_MICROMIPS=y
+CONFIG_CPU_R4K_CACHE_TLB=y
+CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
+CONFIG_CPU_SUPPORTS_HIGHMEM=y
+CONFIG_CPU_SUPPORTS_MSA=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CSRC_R4K=y
+CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_SECTION_MISMATCH=y
+CONFIG_DMA_NONCOHERENT=y
+CONFIG_DMA_NONCOHERENT_CACHE_SYNC=y
+CONFIG_DTC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_EFI_EARLYCON=y
+CONFIG_ETHERNET_PACKET_MANGLE=y
+# CONFIG_FIXED_PHY is not set
+# CONFIG_FONT_SUPPORT is not set
+CONFIG_FW_LOADER_PAGED_BUF=y
+CONFIG_GENERIC_ATOMIC64=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_CPU_AUTOPROBE=y
+CONFIG_GENERIC_GETTIMEOFDAY=y
+CONFIG_GENERIC_IOMAP=y
+CONFIG_GENERIC_IRQ_CHIP=y
+CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y
+CONFIG_GENERIC_IRQ_IPI=y
+CONFIG_GENERIC_IRQ_SHOW=y
+CONFIG_GENERIC_LIB_ASHLDI3=y
+CONFIG_GENERIC_LIB_ASHRDI3=y
+CONFIG_GENERIC_LIB_CMPDI2=y
+CONFIG_GENERIC_LIB_LSHRDI3=y
+CONFIG_GENERIC_LIB_UCMPDI2=y
+CONFIG_GENERIC_PCI_IOMAP=y
+CONFIG_GENERIC_PHY=y
+CONFIG_GENERIC_SCHED_CLOCK=y
+CONFIG_GENERIC_SMP_IDLE_THREAD=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_HANDLE_DOMAIN_IRQ=y
+CONFIG_HARDWARE_WATCHPOINTS=y
+CONFIG_HAS_DMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT_MAP=y
+CONFIG_HAVE_ARCH_COMPILER_H=y
+CONFIG_HAVE_ARCH_JUMP_LABEL=y
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
+CONFIG_HAVE_ARCH_TRACEHOOK=y
+CONFIG_HAVE_ASM_MODVERSIONS=y
+CONFIG_HAVE_CLK=y
+CONFIG_HAVE_CONTEXT_TRACKING=y
+CONFIG_HAVE_COPY_THREAD_TLS=y
+CONFIG_HAVE_C_RECORDMCOUNT=y
+CONFIG_HAVE_DEBUG_KMEMLEAK=y
+CONFIG_HAVE_DEBUG_STACKOVERFLOW=y
+CONFIG_HAVE_DMA_CONTIGUOUS=y
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+CONFIG_HAVE_FAST_GUP=y
+CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_GENERIC_VDSO=y
+CONFIG_HAVE_IDE=y
+CONFIG_HAVE_IOREMAP_PROT=y
+CONFIG_HAVE_IRQ_EXIT_ON_IRQ_STACK=y
+CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
+CONFIG_HAVE_KVM=y
+CONFIG_HAVE_LD_DEAD_CODE_DATA_ELIMINATION=y
+CONFIG_HAVE_MEMBLOCK_NODE_MAP=y
+CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
+CONFIG_HAVE_NET_DSA=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HAVE_PERF_EVENTS=y
+CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
+CONFIG_HAVE_RSEQ=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
+CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_HZ_PERIODIC=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_IRQCHIP=y
+CONFIG_IRQ_DOMAIN=y
+CONFIG_IRQ_DOMAIN_HIERARCHY=y
+CONFIG_IRQ_FORCED_THREADING=y
+CONFIG_IRQ_MIPS_CPU=y
+CONFIG_IRQ_WORK=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+CONFIG_LIBFDT=y
+CONFIG_LOCK_DEBUGGING_SUPPORT=y
+CONFIG_MDIO_BUS=y
+CONFIG_MDIO_DEVICE=y
+CONFIG_MEMFD_CREATE=y
+CONFIG_MFD_SYSCON=y
+CONFIG_MIGRATION=y
+CONFIG_MIPS=y
+CONFIG_MIPS_ASID_BITS=8
+CONFIG_MIPS_ASID_SHIFT=0
+CONFIG_MIPS_CLOCK_VSYSCALL=y
+# CONFIG_MIPS_CMDLINE_DTB_EXTEND is not set
+# CONFIG_MIPS_CMDLINE_FROM_BOOTLOADER is not set
+CONFIG_MIPS_CMDLINE_FROM_DTB=y
+# CONFIG_MIPS_ELF_APPENDED_DTB is not set
+CONFIG_MIPS_L1_CACHE_SHIFT=5
+# CONFIG_MIPS_MT_SMP is not set
+# CONFIG_MIPS_NO_APPENDED_DTB is not set
+CONFIG_MIPS_RAW_APPENDED_DTB=y
+CONFIG_MIPS_SPRAM=y
+# CONFIG_MIPS_VPE_LOADER is not set
+CONFIG_MODULES_USE_ELF_REL=y
+CONFIG_MTD_CFI_ADV_OPTIONS=y
+CONFIG_MTD_CFI_GEOMETRY=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_JEDECPROBE=y
+CONFIG_MTD_SPI_NOR=y
+CONFIG_MTD_SPLIT_BRNIMAGE_FW=y
+CONFIG_MTD_SPLIT_EVA_FW=y
+CONFIG_MTD_SPLIT_FIRMWARE=y
+CONFIG_MTD_SPLIT_TPLINK_FW=y
+CONFIG_MTD_SPLIT_UIMAGE_FW=y
+CONFIG_NEED_DMA_MAP_STATE=y
+CONFIG_NEED_PER_CPU_KM=y
+CONFIG_NET_DEVLINK=y
+CONFIG_NET_DSA=y
+CONFIG_NET_DSA_RTL838X=y
+CONFIG_NET_DSA_TAG_TRAILER=y
+CONFIG_NET_RTL838X=y
+CONFIG_NET_SWITCHDEV=y
+CONFIG_NO_GENERIC_PCI_IOPORT_MAP=y
+CONFIG_NVMEM=y
+CONFIG_OF=y
+CONFIG_OF_ADDRESS=y
+CONFIG_OF_EARLY_FLATTREE=y
+CONFIG_OF_FLATTREE=y
+CONFIG_OF_GPIO=y
+CONFIG_OF_IRQ=y
+CONFIG_OF_KOBJ=y
+CONFIG_OF_MDIO=y
+CONFIG_OF_NET=y
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_PCI_DRIVERS_LEGACY=y
+CONFIG_PERF_USE_VMALLOC=y
+CONFIG_PGTABLE_LEVELS=2
+# CONFIG_PHYLIB is not set
+CONFIG_PHYLINK=y
+CONFIG_PINCTRL=y
+# CONFIG_PINCTRL_SINGLE is not set
+CONFIG_POWER_RESET=y
+CONFIG_POWER_RESET_SYSCON=y
+CONFIG_PSB6970_PHY=y
+CONFIG_REGMAP=y
+CONFIG_REGMAP_MMIO=y
+CONFIG_RESET_CONTROLLER=y
+CONFIG_RTL838X=y
+CONFIG_GPIO_RTL838X=y
+CONFIG_SERIAL_8250_RUNTIME_UARTS=2
+CONFIG_SERIAL_8250_NR_UARTS=2
+CONFIG_SERIAL_MCTRL_GPIO=y
+CONFIG_SPI=y
+CONFIG_SPI_MASTER=y
+CONFIG_SPI_MEM=y
+CONFIG_SPI_RTL838X=y
+CONFIG_SRCU=y
+CONFIG_SWAP_IO_SPACE=y
+CONFIG_SWCONFIG=y
+CONFIG_SWPHY=y
+CONFIG_SYSCTL_EXCEPTION_TRACE=y
+CONFIG_SYS_HAS_CPU_MIPS32_R1=y
+CONFIG_SYS_HAS_CPU_MIPS32_R2=y
+CONFIG_SYS_HAS_EARLY_PRINTK=y
+CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
+CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
+CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
+CONFIG_SYS_SUPPORTS_MIPS16=y
+CONFIG_SYS_SUPPORTS_MULTITHREADING=y
+CONFIG_SYS_SUPPORTS_VPE_LOADER=y
+CONFIG_TARGET_ISA_REV=2
+CONFIG_TICK_CPU_ACCOUNTING=y
+CONFIG_TINY_SRCU=y
+CONFIG_USE_OF=y
+CONFIG_JFFS2_ZLIB=y
diff --git a/target/linux/rtl838x/dts/rtl8382_allnet_all-sg8208m.dts b/target/linux/rtl838x/dts/rtl8382_allnet_all-sg8208m.dts
new file mode 100644
index 0000000000..09d5aff0fe
--- /dev/null
+++ b/target/linux/rtl838x/dts/rtl8382_allnet_all-sg8208m.dts
@@ -0,0 +1,221 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/dts-v1/;
+
+#include "rtl838x.dtsi"
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ compatible = "allnet,all-sg8208m", "realtek,rtl838x-soc";
+ model = "ALLNET ALL-SG8208M";
+
+ aliases {
+ led-boot = &led_sys;
+ led-failsafe = &led_sys;
+ led-running = &led_sys;
+ led-upgrade = &led_sys;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ };
+
+ keys {
+ compatible = "gpio-keys-polled";
+ poll-interval = <20>;
+
+ reset {
+ label = "reset";
+ gpios = <&gpio0 67 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_sys: sys {
+ label = "all-sg8208m:green:sys";
+ gpios = <&gpio0 47 GPIO_ACTIVE_HIGH>;
+ };
+ // GPIO 25: power on/off all port leds
+ };
+};
+
+&gpio0 {
+ indirect-access-bus-id = <0>;
+};
+
+&spi0 {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x80000>;
+ read-only;
+ };
+
+ partition at 80000 {
+ label = "u-boot-env";
+ reg = <0x80000 0x10000>;
+ read-only;
+ };
+
+ partition at 90000 {
+ label = "u-boot-env2";
+ reg = <0x90000 0x10000>;
+ read-only;
+ };
+
+ partition at a0000 {
+ label = "jffs";
+ reg = <0xa0000 0x100000>;
+ };
+
+ partition at 1a0000 {
+ label = "jffs2";
+ reg = <0x1a0000 0x100000>;
+ };
+
+ partition at 2a0000 {
+ label = "firmware";
+ reg = <0x2a0000 0xd60000>;
+ compatible = "allnet,uimage";
+ };
+ };
+ };
+};
+
+ðernet0 {
+ mdio: mdio-bus {
+ compatible = "realtek,rtl838x-mdio";
+ regmap = <ðernet0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Internal phy */
+ phy8: ethernet-phy at 8 {
+ reg = <8>;
+ compatible = "ethernet-phy-ieee802.3-c22";
+ };
+
+ phy9: ethernet-phy at 9 {
+ reg = <9>;
+ compatible = "ethernet-phy-ieee802.3-c22";
+ };
+
+ phy10: ethernet-phy at 10 {
+ reg = <10>;
+ compatible = "ethernet-phy-ieee802.3-c22";
+ };
+
+ phy11: ethernet-phy at 11 {
+ reg = <11>;
+ compatible = "ethernet-phy-ieee802.3-c22";
+ };
+
+ phy12: ethernet-phy at 12 {
+ reg = <12>;
+ compatible = "ethernet-phy-ieee802.3-c22";
+ };
+
+ phy13: ethernet-phy at 13 {
+ reg = <13>;
+ compatible = "ethernet-phy-ieee802.3-c22";
+ };
+
+ phy14: ethernet-phy at 14 {
+ reg = <14>;
+ compatible = "ethernet-phy-ieee802.3-c22";
+ };
+
+ phy15: ethernet-phy at 15 {
+ reg = <15>;
+ compatible = "ethernet-phy-ieee802.3-c22";
+ };
+ };
+};
+
+&switch0 {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <8>;
+ label = "lan1";
+ phy-handle = <&phy8>;
+ phy-mode = "internal";
+ };
+
+ port at 1 {
+ reg = <9>;
+ label = "lan2";
+ phy-handle = <&phy9>;
+ phy-mode = "internal";
+ };
+
+ port at 2 {
+ reg = <10>;
+ label = "lan3";
+ phy-handle = <&phy10>;
+ phy-mode = "internal";
+ };
+
+ port at 3 {
+ reg = <11>;
+ label = "lan4";
+ phy-handle = <&phy11>;
+ phy-mode = "internal";
+ };
+
+ port at 4 {
+ reg = <12>;
+ label = "lan5";
+ phy-handle = <&phy12>;
+ phy-mode = "internal";
+ };
+
+ port at 5 {
+ reg = <13>;
+ label = "lan6";
+ phy-handle = <&phy13>;
+ phy-mode = "internal";
+ };
+
+ port at 6 {
+ reg = <14>;
+ label = "lan7";
+ phy-handle = <&phy14>;
+ phy-mode = "internal";
+ };
+
+ port at 7 {
+ reg = <15>;
+ label = "lan8";
+ phy-handle = <&phy15>;
+ phy-mode = "internal";
+ };
+
+ port at 28 {
+ ethernet = <ðernet0>;
+ reg = <28>;
+ phy-mode = "internal";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+};
diff --git a/target/linux/rtl838x/dts/rtl838x.dtsi b/target/linux/rtl838x/dts/rtl838x.dtsi
new file mode 100644
index 0000000000..63dc9bf1ba
--- /dev/null
+++ b/target/linux/rtl838x/dts/rtl838x.dtsi
@@ -0,0 +1,110 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ compatible = "realtek,rtl838x-soc";
+ reg = <0xbb000000 0xa000>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ frequency = <500000000>;
+
+ cpu at 0 {
+ compatible = "mips,mips4KEc";
+ reg = <0>;
+ };
+ };
+
+ memory at 0 {
+ device_type = "memory";
+ reg = <0x0 0x8000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,38400";
+ };
+
+ cpuintc: cpuintc {
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ compatible = "rtl838x,icu";
+ reg = <0xb8003000 0x20>;
+ };
+
+ spi0: spi at b8001200 {
+ status = "okay";
+
+ compatible = "realtek,rtl838x-nor";
+ reg = <0xb8001200 0x100>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ uart0: uart at b8002000 {
+ status = "disabled";
+
+ compatible = "ns16550a";
+ reg = <0xb8002000 0x100>;
+
+ clock-frequency = <200000000>;
+ interrupts = <31>;
+
+ reg-io-width = <1>;
+ reg-shift = <2>;
+ fifo-size = <1>;
+ no-loopback-test;
+ };
+
+ uart1: uart at b8002100 {
+ status = "okay";
+
+ compatible = "ns16550a";
+ reg = <0xb8002100 0x100>;
+
+ clock-frequency = <200000000>;
+
+ interrupt-parent = <&cpuintc>;
+ interrupts = <30>;
+
+ reg-io-width = <1>;
+ reg-shift = <2>;
+ fifo-size = <1>;
+ no-loopback-test;
+ };
+
+ gpio0: gpio-controller at b8003500 {
+ compatible = "realtek,rtl838x-gpio";
+ reg = <0xb8003500 0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&cpuintc>;
+ interrupts = <23>;
+ };
+
+ ethernet0: ethernet at bb00a300 {
+ status = "okay";
+
+ compatible = "realtek,rtl838x-eth";
+ reg = <0xbb00a300 0x100>;
+ interrupt-parent = <&cpuintc>;
+ interrupts = <24>;
+ #interrupt-cells = <1>;
+ phy-mode = "internal";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ switch0: switch at bb000000 {
+ status = "okay";
+
+ compatible = "realtek,rtl838x-switch";
+ };
+};
diff --git a/target/linux/rtl838x/files-5.4/arch/mips/include/asm/mach-rtl838x/ioremap.h b/target/linux/rtl838x/files-5.4/arch/mips/include/asm/mach-rtl838x/ioremap.h
new file mode 100644
index 0000000000..e7a5bfaffc
--- /dev/null
+++ b/target/linux/rtl838x/files-5.4/arch/mips/include/asm/mach-rtl838x/ioremap.h
@@ -0,0 +1,34 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+#ifndef RTL838X_IOREMAP_H_
+#define RTL838X_IOREMAP_H_
+
+static inline phys_addr_t fixup_bigphys_addr(phys_addr_t phys_addr, phys_addr_t size)
+{
+ return phys_addr;
+}
+
+static inline int is_rtl838x_internal_registers(phys_addr_t offset)
+{
+ /* IO-Block */
+ if (offset >= 0xb8000000 && offset < 0xb9000000)
+ return 1;
+ /* Switch block */
+ if (offset >= 0xbb000000 && offset < 0xbc000000)
+ return 1;
+ return 0;
+}
+
+static inline void __iomem *plat_ioremap(phys_addr_t offset, unsigned long size,
+ unsigned long flags)
+{
+ if (is_rtl838x_internal_registers(offset))
+ return (void __iomem *)offset;
+ return NULL;
+}
+
+static inline int plat_iounmap(const volatile void __iomem *addr)
+{
+ return is_rtl838x_internal_registers((unsigned long)addr);
+}
+
+#endif
diff --git a/target/linux/rtl838x/files-5.4/arch/mips/include/asm/mach-rtl838x/irq.h b/target/linux/rtl838x/files-5.4/arch/mips/include/asm/mach-rtl838x/irq.h
new file mode 100644
index 0000000000..e821111c5d
--- /dev/null
+++ b/target/linux/rtl838x/files-5.4/arch/mips/include/asm/mach-rtl838x/irq.h
@@ -0,0 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+#ifndef __ASM_MACH_RTL838X_IRQ_H
+#define __ASM_MACH_RTL838X_IRQ_H
+
+#define MIPS_CPU_IRQ_BASE 0
+#define NR_IRQS 64
+
+#include_next <irq.h>
+
+#endif /* __ASM_MACH_ATH79_IRQ_H */
diff --git a/target/linux/rtl838x/files-5.4/arch/mips/include/asm/mach-rtl838x/mach-rtl838x.h b/target/linux/rtl838x/files-5.4/arch/mips/include/asm/mach-rtl838x/mach-rtl838x.h
new file mode 100644
index 0000000000..cece36635c
--- /dev/null
+++ b/target/linux/rtl838x/files-5.4/arch/mips/include/asm/mach-rtl838x/mach-rtl838x.h
@@ -0,0 +1,428 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) 2006-2012 Tony Wu (tonywu at realtek.com)
+ * Copyright (C) 2020 B. Koblitz
+ */
+#ifndef _MACH_RTL838X_H_
+#define _MACH_RTL838X_H_
+
+/*
+ * Register access macros
+ */
+
+#define RTL838X_SW_BASE ((volatile void *) 0xBB000000)
+
+#define rtl838x_r32(reg) __raw_readl(reg)
+#define rtl838x_w32(val, reg) __raw_writel(val, reg)
+#define rtl838x_w32_mask(clear, set, reg) rtl838x_w32((rtl838x_r32(reg) & ~(clear)) | (set), reg)
+
+#define sw_r32(reg) __raw_readl(RTL838X_SW_BASE + reg)
+#define sw_w32(val, reg) __raw_writel(val, RTL838X_SW_BASE + reg)
+#define sw_w32_mask(clear, set, reg) \
+ sw_w32((sw_r32(reg) & ~(clear)) | (set), reg)
+
+#define sw_r64(reg) ((((u64)__raw_readl(RTL838X_SW_BASE + reg)) << 32) | \
+ __raw_readl(RTL838X_SW_BASE + reg + 4))
+
+#define sw_w64(val, reg) do { \
+ __raw_writel((u32)((val) >> 32), RTL838X_SW_BASE + reg); \
+ __raw_writel((u32)((val) & 0xffffffff), \
+ RTL838X_SW_BASE + reg + 4); \
+ } while (0)
+
+/*
+ * SPRAM
+ */
+#define RTL838X_ISPRAM_BASE 0x0
+#define RTL838X_DSPRAM_BASE 0x0
+
+/*
+ * IRQ Controller
+ */
+#define RTL838X_IRQ_CPU_BASE 0
+#define RTL838X_IRQ_CPU_NUM 8
+#define RTL838X_IRQ_ICTL_BASE (RTL838X_IRQ_CPU_BASE + RTL838X_IRQ_CPU_NUM)
+#define RTL838X_IRQ_ICTL_NUM 32
+
+/*
+ * MIPS32R2 counter
+ */
+#define RTL838X_COMPARE_IRQ (RTL838X_IRQ_CPU_BASE + 7)
+
+/*
+ * ICTL
+ * Base address 0xb8003000UL
+ */
+#define RTL838X_ICTL1_IRQ (RTL838X_IRQ_CPU_BASE + 2)
+#define RTL838X_ICTL2_IRQ (RTL838X_IRQ_CPU_BASE + 3)
+#define RTL838X_ICTL3_IRQ (RTL838X_IRQ_CPU_BASE + 4)
+#define RTL838X_ICTL4_IRQ (RTL838X_IRQ_CPU_BASE + 5)
+#define RTL838X_ICTL5_IRQ (RTL838X_IRQ_CPU_BASE + 6)
+
+#define GIMR (0x00)
+#define UART0_IE (1 << 31)
+#define UART1_IE (1 << 30)
+#define TC0_IE (1 << 29)
+#define TC1_IE (1 << 28)
+#define OCPTO_IE (1 << 27)
+#define HLXTO_IE (1 << 26)
+#define SLXTO_IE (1 << 25)
+#define NIC_IE (1 << 24)
+#define GPIO_ABCD_IE (1 << 23)
+#define GPIO_EFGH_IE (1 << 22)
+#define RTC_IE (1 << 21)
+#define WDT_IP1_IE (1 << 19)
+#define WDT_IP2_IE (1 << 18)
+
+#define GISR (0x04)
+#define UART0_IP (1 << 31)
+#define UART1_IP (1 << 30)
+#define TC0_IP (1 << 29)
+#define TC1_IP (1 << 28)
+#define OCPTO_IP (1 << 27)
+#define HLXTO_IP (1 << 26)
+#define SLXTO_IP (1 << 25)
+#define NIC_IP (1 << 24)
+#define GPIO_ABCD_IP (1 << 23)
+#define GPIO_EFGH_IP (1 << 22)
+#define RTC_IP (1 << 21)
+#define WDT_IP1_IP (1 << 19)
+#define WDT_IP2_IP (1 << 18)
+
+#define IRR0 (0x08)
+#define IRR0_SETTING ((UART0_RS << 28) | \
+ (UART1_RS << 24) | \
+ (TC0_RS << 20) | \
+ (TC1_RS << 16) | \
+ (OCPTO_RS << 12) | \
+ (HLXTO_RS << 8) | \
+ (SLXTO_RS << 4) | \
+ (NIC_RS << 0) \
+ )
+
+#define IRR1 (0x0c)
+
+#define IRR1_SETTING ((GPIO_ABCD_RS << 28) | \
+ (GPIO_EFGH_RS << 24) | \
+ (RTC_RS << 20) | \
+ (SWCORE_RS << 16) \
+ )
+
+#define IRR2 (0x10)
+#define IRR2_SETTING 0
+
+#define IRR3 (0x14)
+#define IRR3_SETTING 0
+
+/* Interrupt Routing Selection */
+#define UART0_RS 2
+#define UART1_RS 1
+#define TC0_RS 5
+#define TC1_RS 1
+#define OCPTO_RS 1
+#define HLXTO_RS 1
+#define SLXTO_RS 1
+#define NIC_RS 4
+#define GPIO_ABCD_RS 4
+#define GPIO_EFGH_RS 4
+#define RTC_RS 4
+#define SWCORE_RS 3
+#define WDT_IP1_RS 4
+#define WDT_IP2_RS 5
+
+/* Interrupt IRQ Assignments */
+#define UART0_IRQ 31
+#define UART1_IRQ 30
+#define TC0_IRQ 29
+#define TC1_IRQ 28
+#define OCPTO_IRQ 27
+#define HLXTO_IRQ 26
+#define SLXTO_IRQ 25
+#define NIC_IRQ 24
+#define GPIO_ABCD_IRQ 23
+#define GPIO_EFGH_IRQ 22
+#define RTC_IRQ 21
+#define SWCORE_IRQ 20
+#define WDT_IP1_IRQ 19
+#define WDT_IP2_IRQ 18
+
+#define SYSTEM_FREQ 200000000
+#define RTL838X_UART0_BASE ((volatile void *)(0xb8002000UL))
+#define RTL838X_UART0_BAUD 38400 /* ex. 19200 or 38400 or 57600 or 115200 */
+#define RTL838X_UART0_FREQ (SYSTEM_FREQ - RTL838X_UART0_BAUD * 24)
+#define RTL838X_UART0_MAPBASE 0x18002000UL
+#define RTL838X_UART0_MAPSIZE 0x100
+#define RTL838X_UART0_IRQ UART0_IRQ
+
+#define RTL838X_UART1_BASE ((volatile void *)(0xb8002100UL))
+#define RTL838X_UART1_BAUD 38400 /* ex. 19200 or 38400 or 57600 or 115200 */
+#define RTL838X_UART1_FREQ (SYSTEM_FREQ - RTL838X_UART1_BAUD * 24)
+#define RTL838X_UART1_MAPBASE 0x18002100UL
+#define RTL838X_UART1_MAPSIZE 0x100
+#define RTL838X_UART1_IRQ UART1_IRQ
+
+#define UART0_RBR (RTL838X_UART0_BASE + 0x000)
+#define UART0_THR (RTL838X_UART0_BASE + 0x000)
+#define UART0_DLL (RTL838X_UART0_BASE + 0x000)
+#define UART0_IER (RTL838X_UART0_BASE + 0x004)
+#define UART0_DLM (RTL838X_UART0_BASE + 0x004)
+#define UART0_IIR (RTL838X_UART0_BASE + 0x008)
+#define UART0_FCR (RTL838X_UART0_BASE + 0x008)
+#define UART0_LCR (RTL838X_UART0_BASE + 0x00C)
+#define UART0_MCR (RTL838X_UART0_BASE + 0x010)
+#define UART0_LSR (RTL838X_UART0_BASE + 0x014)
+
+#define UART1_RBR (RTL838X_UART1_BASE + 0x000)
+#define UART1_THR (RTL838X_UART1_BASE + 0x000)
+#define UART1_DLL (RTL838X_UART1_BASE + 0x000)
+#define UART1_IER (RTL838X_UART1_BASE + 0x004)
+#define UART1_DLM (RTL838X_UART1_BASE + 0x004)
+#define UART1_IIR (RTL838X_UART1_BASE + 0x008)
+#define UART1_FCR (RTL838X_UART1_BASE + 0x008)
+ #define FCR_EN 0x01
+ #define FCR_RXRST 0x02
+ #define XRST 0x02
+ #define FCR_TXRST 0x04
+ #define TXRST 0x04
+ #define FCR_DMA 0x08
+ #define FCR_RTRG 0xC0
+ #define CHAR_TRIGGER_01 0x00
+ #define CHAR_TRIGGER_04 0x40
+ #define CHAR_TRIGGER_08 0x80
+ #define CHAR_TRIGGER_14 0xC0
+#define UART1_LCR (RTL838X_UART1_BASE + 0x00C)
+ #define LCR_WLN 0x03
+ #define CHAR_LEN_5 0x00
+ #define CHAR_LEN_6 0x01
+ #define CHAR_LEN_7 0x02
+ #define CHAR_LEN_8 0x03
+ #define LCR_STB 0x04
+ #define ONE_STOP 0x00
+ #define TWO_STOP 0x04
+ #define LCR_PEN 0x08
+ #define PARITY_ENABLE 0x01
+ #define PARITY_DISABLE 0x00
+ #define LCR_EPS 0x30
+ #define PARITY_ODD 0x00
+ #define PARITY_EVEN 0x10
+ #define PARITY_MARK 0x20
+ #define PARITY_SPACE 0x30
+ #define LCR_BRK 0x40
+ #define LCR_DLAB 0x80
+ #define DLAB 0x80
+#define UART1_MCR (RTL838X_UART1_BASE + 0x010)
+#define UART1_LSR (RTL838X_UART1_BASE + 0x014)
+ #define LSR_DR 0x01
+ #define RxCHAR_AVAIL 0x01
+ #define LSR_OE 0x02
+ #define LSR_PE 0x04
+ #define LSR_FE 0x08
+ #define LSR_BI 0x10
+ #define LSR_THRE 0x20
+ #define TxCHAR_AVAIL 0x00
+ #define TxCHAR_EMPTY 0x20
+ #define LSR_TEMT 0x40
+ #define LSR_RFE 0x80
+
+/*
+ * Timer/counter for 8390/80/28 TC & MP chip
+ */
+#define RTL838X_TIMER0_BASE ((volatile void *)(0xb8003100UL))
+#define RTL838X_TIMER0_IRQ RTL838X_TC0_EXT_IRQ
+
+#define RTL8390TC_TC1DATA (RTL838X_TIMER0_BASE + 0x04)
+#define RTL8390TC_TCD_OFFSET 8
+#define RTL8390TC_TC0CNT (RTL838X_TIMER0_BASE + 0x08)
+#define RTL8390TC_TC1CNT (RTL838X_TIMER0_BASE + 0x0C)
+#define RTL8390TC_TCCNR (RTL838X_TIMER0_BASE + 0x10)
+#define RTL8390TC_TC0EN (1 << 31)
+#define RTL8390TC_TC0MODE_TIMER (1 << 30)
+#define RTL8390TC_TC1EN (1 << 29)
+#define RTL8390TC_TC1MODE_TIMER (1 << 28)
+#define RTL8390TC_TCIR (RTL838X_TIMER0_BASE + 0x14)
+#define RTL8390TC_TC0IE (1 << 31)
+#define RTL8390TC_TC1IE (1 << 30)
+#define RTL8390TC_TC0IP (1 << 29)
+#define RTL8390TC_TC1IP (1 << 28)
+#define RTL8390TC_CDBR (RTL838X_TIMER0_BASE + 0x18)
+#define RTL8390TC_DIVF_OFFSET 16
+#define RTL8390TC_WDTCNR (RTL838X_TIMER0_BASE + 0x1C)
+
+#define RTL8390MP_TC1DATA (RTL838X_TIMER0_BASE + 0x10)
+#define RTL8390MP_TC0CNT (RTL838X_TIMER0_BASE + 0x04)
+#define RTL8390MP_TC1CNT (RTL838X_TIMER0_BASE + 0x14)
+#define RTL8390MP_TC0CTL (RTL838X_TIMER0_BASE + 0x08)
+#define RTL8390MP_TC1CTL (RTL838X_TIMER0_BASE + 0x18)
+#define RTL8390MP_TCEN (1 << 28)
+#define RTL8390MP_TCMODE_TIMER (1 << 24)
+#define RTL8390MP_TCDIV_FACTOR (0xFFFF << 0)
+#define RTL8390MP_TC0INT (RTL838X_TIMER0_BASE + 0xC)
+#define RTL8390MP_TC1INT (RTL838X_TIMER0_BASE + 0x1C)
+#define RTL8390MP_TCIE (1 << 20)
+#define RTL8390MP_TCIP (1 << 16)
+#define RTL8390MP_WDTCNR (RTL838X_TIMER0_BASE + 0x50)
+
+#define RTL8380MP_TC0DATA (RTL838X_TIMER0_BASE + 0x00)
+#define RTL8380MP_TC1DATA (RTL838X_TIMER0_BASE + 0x10)
+#define RTL8380MP_TC0CNT (RTL838X_TIMER0_BASE + 0x04)
+#define RTL8380MP_TC1CNT (RTL838X_TIMER0_BASE + 0x14)
+#define RTL8380MP_TC0CTL (RTL838X_TIMER0_BASE + 0x08)
+#define RTL8380MP_TC1CTL (RTL838X_TIMER0_BASE + 0x18)
+#define RTL8380MP_TCEN (1 << 28)
+#define RTL8380MP_TCMODE_TIMER (1 << 24)
+#define RTL8380MP_TCDIV_FACTOR (0xFFFF << 0)
+#define RTL8380MP_TC0INT (RTL838X_TIMER0_BASE + 0xC)
+#define RTL8380MP_TC1INT (RTL838X_TIMER0_BASE + 0x1C)
+#define RTL8380MP_TCIE (1 << 20)
+#define RTL8380MP_TCIP (1 << 16)
+#define RTL8380MP_WDTCNR (RTL838X_TIMER0_BASE + 0x50)
+
+#define DIVISOR_RTL8390 55
+#define DIVISOR_RTL8380 2500
+#define DIVISOR_MAX 16834
+
+/*
+ * Memory Controller
+ */
+#define MC_MCR 0xB8001000
+#define MC_MCR_VAL 0x00000000
+
+#define MC_DCR 0xB8001004
+#define MC_DCR0_VAL 0x54480000
+
+#define MC_DTCR 0xB8001008
+#define MC_DTCR_VAL 0xFFFF05C0
+
+/*
+ * GPIO
+ */
+#define GPIO_CTRL_REG_BASE ((volatile void *) 0xb8003500)
+#define RTL838X_GPIO_PABC_CNR (GPIO_CTRL_REG_BASE + 0x0)
+#define RTL838X_GPIO_PABC_TYPE (GPIO_CTRL_REG_BASE + 0x04)
+#define RTL838X_GPIO_PABC_DIR (GPIO_CTRL_REG_BASE + 0x8)
+#define RTL838X_GPIO_PABC_DATA (GPIO_CTRL_REG_BASE + 0xc)
+#define RTL838X_GPIO_PABC_ISR (GPIO_CTRL_REG_BASE + 0x10)
+#define RTL838X_GPIO_PAB_IMR (GPIO_CTRL_REG_BASE + 0x14)
+#define RTL838X_GPIO_PC_IMR (GPIO_CTRL_REG_BASE + 0x18)
+
+#define RTL838X_MODEL_NAME_INFO (0x00D4)
+#define RTL839X_MODEL_NAME_INFO (0x0FF0)
+#define RTL838X_LED_GLB_CTRL (0xA000)
+#define RTL839X_LED_GLB_CTRL (0x00E4)
+#define RTL838X_EXT_GPIO_DIR_0 (0xA08C)
+#define RTL838X_EXT_GPIO_DIR_1 (0xA090)
+#define RTL838X_EXT_GPIO_DATA_0 (0xA094)
+#define RTL838X_EXT_GPIO_DATA_1 (0xA098)
+#define RTL838X_EXT_GPIO_INDRT_ACCESS (0xA09C)
+#define RTL838X_EXTRA_GPIO_CTRL (0xA0E0)
+#define RTL838X_EXTRA_GPIO_DIR_0 (0xA0E4)
+#define RTL838X_EXTRA_GPIO_DIR_1 (0xA0E8)
+#define RTL838X_EXTRA_GPIO_DATA_0 (0xA0EC)
+#define RTL838X_EXTRA_GPIO_DATA_1 (0xA0F0)
+#define RTL838X_DMY_REG5 (0x0144)
+#define RTL838X_EXTRA_GPIO_CTRL (0xA0E0)
+
+#define RTL838X_GMII_INTF_SEL (0x1000)
+#define RTL838X_IO_DRIVING_ABILITY_CTRL (0x1010)
+
+#define RTL838X_GPIO_A7 31
+#define RTL838X_GPIO_A6 30
+#define RTL838X_GPIO_A5 29
+#define RTL838X_GPIO_A4 28
+#define RTL838X_GPIO_A3 27
+#define RTL838X_GPIO_A2 26
+#define RTL838X_GPIO_A1 25
+#define RTL838X_GPIO_A0 24
+#define RTL838X_GPIO_B7 23
+#define RTL838X_GPIO_B6 22
+#define RTL838X_GPIO_B5 21
+#define RTL838X_GPIO_B4 20
+#define RTL838X_GPIO_B3 19
+#define RTL838X_GPIO_B2 18
+#define RTL838X_GPIO_B1 17
+#define RTL838X_GPIO_B0 16
+#define RTL838X_GPIO_C7 15
+#define RTL838X_GPIO_C6 14
+#define RTL838X_GPIO_C5 13
+#define RTL838X_GPIO_C4 12
+#define RTL838X_GPIO_C3 11
+#define RTL838X_GPIO_C2 10
+#define RTL838X_GPIO_C1 9
+#define RTL838X_GPIO_C0 8
+
+#define RTL838X_INT_RW_CTRL (0x0058)
+#define RTL838X_EXT_VERSION (0x00D0)
+#define RTL838X_PLL_CML_CTRL (0x0FF8)
+#define RTL838X_STRAP_DBG (0x100C)
+
+/*
+ * Reset
+ */
+#define RGCR (0x1E70)
+#define RTL839X_RST_GLB_CTRL (0x0014)
+#define RTL838X_RST_GLB_CTRL_1 (0x0040)
+
+/* LED control by switch */
+#define RTL838X_LED_MODE_SEL (0x1004)
+#define RTL838X_LED_MODE_CTRL (0xA004)
+#define RTL838X_LED_P_EN_CTRL (0xA008)
+
+/* LED control by software */
+#define RTL838X_LED_SW_CTRL (0xA00C)
+#define RTL838X_LED0_SW_P_EN_CTRL (0xA010)
+#define RTL838X_LED1_SW_P_EN_CTRL (0xA014)
+#define RTL838X_LED2_SW_P_EN_CTRL (0xA018)
+#define RTL838X_LED_SW_P_CTRL(p) (0xA01C + ((p) << 2))
+
+#define RTL839X_MAC_EFUSE_CTRL (0x02ac)
+
+/*
+ * MDIO via Realtek's SMI interface
+ */
+#define RTL838X_SMI_GLB_CTRL (0xa100)
+#define RTL838X_SMI_ACCESS_PHY_CTRL_0 (0xa1b8)
+#define RTL838X_SMI_ACCESS_PHY_CTRL_1 (0xa1bc)
+#define RTL838X_SMI_ACCESS_PHY_CTRL_2 (0xa1c0)
+#define RTL838X_SMI_ACCESS_PHY_CTRL_3 (0xa1c4)
+#define RTL838X_SMI_PORT0_5_ADDR_CTRL (0xa1c8)
+#define RTL838X_SMI_POLL_CTRL (0xa17c)
+
+#define RTL839X_SMI_GLB_CTRL (0x03f8)
+#define RTL839X_SMI_PORT_POLLING_CTRL (0x03fc)
+#define RTL839X_PHYREG_ACCESS_CTRL (0x03DC)
+#define RTL839X_PHYREG_CTRL (0x03E0)
+#define RTL839X_PHYREG_PORT_CTRL(p) (0x03E4 + ((p >> 5) << 2))
+#define RTL839X_PHYREG_DATA_CTRL (0x03F0)
+
+/*
+ * Switch interrupts
+ */
+#define RTL838X_IMR_GLB (0x1100)
+#define RTL838X_IMR_PORT_LINK_STS_CHG (0x1104)
+#define RTL838X_ISR_GLB_SRC (0x1148)
+#define RTL838X_ISR_PORT_LINK_STS_CHG (0x114C)
+#define RTL839X_IMR_GLB (0x0064)
+#define RTL839X_IMR_PORT_LINK_STS_CHG (0x0068)
+#define RTL839X_ISR_GLB_SRC (0x009c)
+#define RTL839X_ISR_PORT_LINK_STS_CHG (0x00a0)
+
+/* Definition of family IDs */
+#define RTL8389_FAMILY_ID (0x8389)
+#define RTL8328_FAMILY_ID (0x8328)
+#define RTL8390_FAMILY_ID (0x8390)
+#define RTL8350_FAMILY_ID (0x8350)
+#define RTL8380_FAMILY_ID (0x8380)
+#define RTL8330_FAMILY_ID (0x8330)
+
+struct rtl838x_soc_info {
+ unsigned char *name;
+ unsigned int id;
+ unsigned int family;
+ unsigned char *compatible;
+ volatile void *sw_base;
+ volatile void *icu_base;
+};
+
+void rtl838x_soc_detect(struct rtl838x_soc_info *i);
+
+#endif /* _MACH_RTL838X_H_ */
diff --git a/target/linux/rtl838x/files-5.4/arch/mips/rtl838x/Makefile b/target/linux/rtl838x/files-5.4/arch/mips/rtl838x/Makefile
new file mode 100644
index 0000000000..fe5e1d96a9
--- /dev/null
+++ b/target/linux/rtl838x/files-5.4/arch/mips/rtl838x/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for the rtl838x specific parts of the kernel
+#
+
+obj-y := serial.o setup.o prom.o irq.o
diff --git a/target/linux/rtl838x/files-5.4/arch/mips/rtl838x/Platform b/target/linux/rtl838x/files-5.4/arch/mips/rtl838x/Platform
new file mode 100644
index 0000000000..4d48932d80
--- /dev/null
+++ b/target/linux/rtl838x/files-5.4/arch/mips/rtl838x/Platform
@@ -0,0 +1,6 @@
+#
+# Realtek RTL838x SoCs
+#
+platform-$(CONFIG_RTL838X) += rtl838x/
+cflags-$(CONFIG_RTL838X) += -I$(srctree)/arch/mips/include/asm/mach-rtl838x/
+load-$(CONFIG_RTL838X) += 0xffffffff80000000
diff --git a/target/linux/rtl838x/files-5.4/arch/mips/rtl838x/irq.c b/target/linux/rtl838x/files-5.4/arch/mips/rtl838x/irq.c
new file mode 100644
index 0000000000..34e90982b2
--- /dev/null
+++ b/target/linux/rtl838x/files-5.4/arch/mips/rtl838x/irq.c
@@ -0,0 +1,263 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Realtek RTL838X architecture specific IRQ handling
+ *
+ * Copyright (C) 2020 B. Koblitz
+ * based on the original BSP
+ * Copyright (C) 2006-2012 Tony Wu (tonywu at realtek.com)
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/irqchip.h>
+#include <linux/of_irq.h>
+#include <linux/of_address.h>
+#include <linux/spinlock.h>
+
+#include <asm/irq_cpu.h>
+#include <asm/mipsregs.h>
+#include <mach-rtl838x.h>
+
+extern struct rtl838x_soc_info soc_info;
+
+#define icu_r32(reg) rtl838x_r32(soc_info.icu_base + reg)
+#define icu_w32(val, reg) rtl838x_w32(val, soc_info.icu_base + reg)
+#define icu_w32_mask(clear, set, reg) rtl838x_w32_mask(clear, set, soc_info.icu_base + reg)
+
+static DEFINE_RAW_SPINLOCK(irq_lock);
+
+extern irqreturn_t c0_compare_interrupt(int irq, void *dev_id);
+unsigned int rtl838x_ictl_irq_dispatch1(void);
+unsigned int rtl838x_ictl_irq_dispatch2(void);
+unsigned int rtl838x_ictl_irq_dispatch3(void);
+unsigned int rtl838x_ictl_irq_dispatch4(void);
+unsigned int rtl838x_ictl_irq_dispatch5(void);
+
+static struct irqaction irq_cascade1 = {
+ .handler = no_action,
+ .name = "RTL838X IRQ cascade1",
+};
+
+static struct irqaction irq_cascade2 = {
+ .handler = no_action,
+ .name = "RTL838X IRQ cascade2",
+};
+
+static struct irqaction irq_cascade3 = {
+ .handler = no_action,
+ .name = "RTL838X IRQ cascade3",
+};
+
+static struct irqaction irq_cascade4 = {
+ .handler = no_action,
+ .name = "RTL838X IRQ cascade4",
+};
+
+static struct irqaction irq_cascade5 = {
+ .handler = no_action,
+ .name = "RTL838X IRQ cascade5",
+};
+
+static void rtl838x_ictl_enable_irq(struct irq_data *i)
+{
+ unsigned long flags;
+
+ raw_spin_lock_irqsave(&irq_lock, flags);
+ icu_w32_mask(0, 1 << i->irq, GIMR);
+ raw_spin_unlock_irqrestore(&irq_lock, flags);
+}
+
+static unsigned int rtl838x_ictl_startup_irq(struct irq_data *i)
+{
+ rtl838x_ictl_enable_irq(i);
+ return 0;
+}
+
+static void rtl838x_ictl_disable_irq(struct irq_data *i)
+{
+ unsigned long flags;
+
+ raw_spin_lock_irqsave(&irq_lock, flags);
+ icu_w32_mask(1 << i->irq, 0, GIMR);
+ raw_spin_unlock_irqrestore(&irq_lock, flags);
+}
+
+static void rtl838x_ictl_eoi_irq(struct irq_data *i)
+{
+ unsigned long flags;
+
+ raw_spin_lock_irqsave(&irq_lock, flags);
+ icu_w32_mask(0, 1 << i->irq, GIMR);
+ raw_spin_unlock_irqrestore(&irq_lock, flags);
+}
+
+static struct irq_chip rtl838x_ictl_irq = {
+ .name = "RTL838X",
+ .irq_startup = rtl838x_ictl_startup_irq,
+ .irq_shutdown = rtl838x_ictl_disable_irq,
+ .irq_enable = rtl838x_ictl_enable_irq,
+ .irq_disable = rtl838x_ictl_disable_irq,
+ .irq_ack = rtl838x_ictl_disable_irq,
+ .irq_mask = rtl838x_ictl_disable_irq,
+ .irq_unmask = rtl838x_ictl_enable_irq,
+ .irq_eoi = rtl838x_ictl_eoi_irq,
+};
+
+/*
+ * RTL8390/80/28 Interrupt Scheme
+ *
+ * Source IRQ CPU INT
+ * -------- ------- -------
+ * UART0 31 IP3
+ * UART1 30 IP2
+ * TIMER0 29 IP6
+ * TIMER1 28 IP2
+ * OCPTO 27 IP2
+ * HLXTO 26 IP2
+ * SLXTO 25 IP2
+ * NIC 24 IP5
+ * GPIO_ABCD 23 IP5
+ * SWCORE 20 IP4
+ */
+
+unsigned int rtl838x_ictl_irq_dispatch1(void)
+{
+ /* Identify shared IRQ */
+ unsigned int extint_ip = icu_r32(GIMR) & icu_r32(GISR);
+
+ if (extint_ip & TC1_IP)
+ do_IRQ(TC1_IRQ);
+ else if (extint_ip & UART1_IP)
+ do_IRQ(UART1_IRQ);
+ else
+ spurious_interrupt();
+
+ return IRQ_HANDLED;
+}
+
+unsigned int rtl838x_ictl_irq_dispatch2(void)
+{
+ do_IRQ(UART0_IRQ);
+ return IRQ_HANDLED;
+}
+
+unsigned int rtl838x_ictl_irq_dispatch3(void)
+{
+ do_IRQ(SWCORE_IRQ);
+ return IRQ_HANDLED;
+}
+
+unsigned int rtl838x_ictl_irq_dispatch4(void)
+{
+ /* Identify shared IRQ */
+ unsigned int extint_ip = icu_r32(GIMR) & icu_r32(GISR);
+
+ if (extint_ip & NIC_IP)
+ do_IRQ(NIC_IRQ);
+ else if (extint_ip & GPIO_ABCD_IP)
+ do_IRQ(GPIO_ABCD_IRQ);
+ else if ((extint_ip & GPIO_EFGH_IP) && (soc_info.family == RTL8328_FAMILY_ID))
+ do_IRQ(GPIO_EFGH_IRQ);
+ else
+ spurious_interrupt();
+
+ return IRQ_HANDLED;
+}
+
+unsigned int rtl838x_ictl_irq_dispatch5(void)
+{
+ do_IRQ(TC0_IRQ);
+ return IRQ_HANDLED;
+}
+
+asmlinkage void plat_irq_dispatch(void)
+{
+ unsigned int pending;
+
+ pending = read_c0_cause() & read_c0_status() & ST0_IM;
+
+ if (pending & CAUSEF_IP7)
+ c0_compare_interrupt(7, NULL);
+ else if (pending & CAUSEF_IP6)
+ rtl838x_ictl_irq_dispatch5();
+ else if (pending & CAUSEF_IP5)
+ rtl838x_ictl_irq_dispatch4();
+ else if (pending & CAUSEF_IP4)
+ rtl838x_ictl_irq_dispatch3();
+ else if (pending & CAUSEF_IP3)
+ rtl838x_ictl_irq_dispatch2();
+ else if (pending & CAUSEF_IP2)
+ rtl838x_ictl_irq_dispatch1();
+ else
+ spurious_interrupt();
+}
+
+static void __init rtl838x_ictl_irq_init(unsigned int irq_base)
+{
+ int i;
+
+ for (i = 0; i < RTL838X_IRQ_ICTL_NUM; i++)
+ irq_set_chip_and_handler(irq_base + i, &rtl838x_ictl_irq, handle_level_irq);
+
+ setup_irq(RTL838X_ICTL1_IRQ, &irq_cascade1);
+ setup_irq(RTL838X_ICTL2_IRQ, &irq_cascade2);
+ setup_irq(RTL838X_ICTL3_IRQ, &irq_cascade3);
+ setup_irq(RTL838X_ICTL4_IRQ, &irq_cascade4);
+ setup_irq(RTL838X_ICTL5_IRQ, &irq_cascade5);
+
+ /* Set GIMR, IRR */
+ icu_w32(TC0_IE | UART0_IE, GIMR);
+ icu_w32(IRR0_SETTING, IRR0);
+ icu_w32(IRR1_SETTING, IRR1);
+ icu_w32(IRR2_SETTING, IRR2);
+ icu_w32(IRR3_SETTING, IRR3);
+}
+
+static int intc_map(struct irq_domain *d, unsigned int irq, irq_hw_number_t hw)
+{
+ irq_set_chip_and_handler(hw, &rtl838x_ictl_irq, handle_level_irq);
+
+ return 0;
+}
+
+static const struct irq_domain_ops irq_domain_ops = {
+ .xlate = irq_domain_xlate_onecell,
+ .map = intc_map,
+};
+
+int __init icu_of_init(struct device_node *node, struct device_node *parent)
+{
+ int i;
+ struct irq_domain *domain;
+ struct resource res;
+
+ pr_info("Found Interrupt controller: %s (%s)\n", node->name, node->full_name);
+ if (of_address_to_resource(node, 0, &res)) {
+ panic("Failed to get icu memory range");
+ }
+ if (!request_mem_region(res.start, resource_size(&res), res.name))
+ pr_err("Failed to request icu memory\n");
+ soc_info.icu_base = ioremap(res.start, resource_size(&res));
+ pr_info("ICU Memory: %08x\n", (u32)soc_info.icu_base);
+
+ mips_cpu_irq_init();
+
+ domain = irq_domain_add_simple(node, 32, 0, &irq_domain_ops, NULL);
+
+ /* Setup all external HW irqs */
+ for (i = 8; i < 32; i++)
+ irq_domain_associate(domain, i, i);
+
+ rtl838x_ictl_irq_init(RTL838X_IRQ_ICTL_BASE);
+ return 0;
+}
+
+void __init arch_init_irq(void)
+{
+ /* do board-specific irq initialization */
+ irqchip_init();
+}
+
+IRQCHIP_DECLARE(mips_cpu_intc, "rtl838x,icu", icu_of_init);
diff --git a/target/linux/rtl838x/files-5.4/arch/mips/rtl838x/prom.c b/target/linux/rtl838x/files-5.4/arch/mips/rtl838x/prom.c
new file mode 100644
index 0000000000..604b01806c
--- /dev/null
+++ b/target/linux/rtl838x/files-5.4/arch/mips/rtl838x/prom.c
@@ -0,0 +1,174 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * prom.c
+ * Early intialization code for the Realtek RTL838X SoC
+ *
+ * based on the original BSP by
+ * Copyright (C) 2006-2012 Tony Wu (tonywu at realtek.com)
+ * Copyright (C) 2020 B. Koblitz
+ *
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/of_fdt.h>
+#include <linux/libfdt.h>
+#include <asm/bootinfo.h>
+#include <asm/addrspace.h>
+#include <asm/page.h>
+#include <asm/cpu.h>
+
+#include <mach-rtl838x.h>
+
+extern char arcs_cmdline[];
+const void *fdt;
+extern const char __appended_dtb;
+//extern int __init rtl838x_serial_init(void);
+
+void prom_console_init(void)
+{
+ /* UART 16550A is initialized by the bootloader */
+}
+
+#ifdef CONFIG_EARLY_PRINTK
+#define rtl838x_r8(reg) __raw_readb(reg)
+#define rtl838x_w8(val, reg) __raw_writeb(val, reg)
+
+void unregister_prom_console(void)
+{
+
+}
+
+void disable_early_printk(void)
+{
+
+}
+
+void prom_putchar(char c)
+{
+ unsigned int retry = 0;
+
+ do {
+ if (retry++ >= 30000) {
+ /* Reset Tx FIFO */
+ rtl838x_w8(TXRST | CHAR_TRIGGER_14, UART0_FCR);
+ return;
+ }
+ } while ((rtl838x_r8(UART0_LSR) & LSR_THRE) == TxCHAR_AVAIL);
+
+ /* Send Character */
+ rtl838x_w8(c, UART0_THR);
+}
+
+char prom_getchar(void)
+{
+ return '\0';
+}
+#endif
+
+struct rtl838x_soc_info soc_info;
+
+const char *get_system_type(void)
+{
+ return soc_info.name;
+}
+
+
+void __init prom_free_prom_memory(void)
+{
+
+}
+
+void __init device_tree_init(void)
+{
+ pr_info("%s called\r\n", __func__);
+ if (!fdt_check_header(&__appended_dtb)) {
+ fdt = &__appended_dtb;
+ pr_info("Using appended Device Tree.\n");
+ }
+ initial_boot_params = (void *)fdt;
+ unflatten_and_copy_device_tree();
+}
+
+static void __init prom_init_cmdline(void)
+{
+ int argc = fw_arg0;
+ char **argv = (char **) KSEG1ADDR(fw_arg1);
+ int i;
+
+ arcs_cmdline[0] = '\0';
+
+ for (i = 0; i < argc; i++) {
+ char *p = (char *) KSEG1ADDR(argv[i]);
+
+ if (CPHYSADDR(p) && *p) {
+ strlcat(arcs_cmdline, p, sizeof(arcs_cmdline));
+ strlcat(arcs_cmdline, " ", sizeof(arcs_cmdline));
+ }
+ }
+ pr_info("Kernel command line: %s\n", arcs_cmdline);
+}
+
+/* Do basic initialization */
+void __init prom_init(void)
+{
+ uint32_t model;
+
+ pr_info("%s called\n", __func__);
+ soc_info.sw_base = RTL838X_SW_BASE;
+
+ model = sw_r32(RTL838X_MODEL_NAME_INFO);
+ pr_info("RTL838X model is %x\n", model);
+ model = model >> 16 & 0xFFFF;
+
+ if ((model != 0x8328) && (model != 0x8330) && (model != 0x8332)
+ && (model != 0x8380) && (model != 0x8382)) {
+ model = sw_r32(RTL839X_MODEL_NAME_INFO);
+ pr_info("RTL839X model is %x\n", model);
+ model = model >> 16 & 0xFFFF;
+ }
+
+ soc_info.id = model;
+
+ switch (model) {
+ case 0x8328:
+ soc_info.name = "RTL8328";
+ soc_info.family = RTL8328_FAMILY_ID;
+ break;
+ case 0x8332:
+ soc_info.name = "RTL8332";
+ soc_info.family = RTL8380_FAMILY_ID;
+ break;
+ case 0x8380:
+ soc_info.name = "RTL8380";
+ soc_info.family = RTL8380_FAMILY_ID;
+ break;
+ case 0x8382:
+ soc_info.name = "RTL8382";
+ soc_info.family = RTL8380_FAMILY_ID;
+ break;
+ case 0x8390:
+ soc_info.name = "RTL8390";
+ soc_info.family = RTL8390_FAMILY_ID;
+ break;
+ case 0x8391:
+ soc_info.name = "RTL8391";
+ soc_info.family = RTL8390_FAMILY_ID;
+ break;
+ case 0x8392:
+ soc_info.name = "RTL8392";
+ soc_info.family = RTL8390_FAMILY_ID;
+ break;
+ case 0x8393:
+ soc_info.name = "RTL8393";
+ soc_info.family = RTL8390_FAMILY_ID;
+ break;
+ default:
+ soc_info.name = "DEFAULT";
+ soc_info.family = 0;
+ }
+ pr_info("SoC Type: %s\n", get_system_type());
+ prom_init_cmdline();
+}
+
diff --git a/target/linux/rtl838x/files-5.4/arch/mips/rtl838x/serial.c b/target/linux/rtl838x/files-5.4/arch/mips/rtl838x/serial.c
new file mode 100644
index 0000000000..cebab1df8d
--- /dev/null
+++ b/target/linux/rtl838x/files-5.4/arch/mips/rtl838x/serial.c
@@ -0,0 +1,100 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * 8250 serial console setup for the Realtek RTL838X SoC
+ *
+ * based on the original BSP by
+ * Copyright (C) 2006-2012 Tony Wu (tonywu at realtek.com)
+ *
+ * Copyright (C) 2020 B. Koblitz
+ *
+ */
+#include <linux/types.h>
+#include <linux/ctype.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/version.h>
+#include <linux/serial.h>
+#include <linux/serial_core.h>
+#include <linux/serial_8250.h>
+#include <linux/serial_reg.h>
+#include <linux/tty.h>
+#include <linux/clk.h>
+
+#include <asm/mach-rtl838x/mach-rtl838x.h>
+
+extern char arcs_cmdline[];
+extern struct rtl838x_soc_info soc_info;
+
+int __init rtl838x_serial_init(void)
+{
+#ifdef CONFIG_SERIAL_8250
+ int ret;
+ struct uart_port p;
+ unsigned long baud = 0;
+ int err;
+ char parity = '\0', bits = '\0', flow = '\0';
+ char *s;
+ struct device_node *dn;
+
+ dn = of_find_compatible_node(NULL, NULL, "ns16550a");
+ if (dn) {
+ pr_info("Found NS16550a: %s (%s)\n", dn->name, dn->full_name);
+ dn = of_find_compatible_node(dn, NULL, "ns16550a");
+ if (dn && of_device_is_available(dn) && soc_info.family == RTL8380_FAMILY_ID) {
+ /* Enable UART1 on RTL838x */
+ pr_info("Enabling uart1\n");
+ sw_w32(0x10, RTL838X_GMII_INTF_SEL);
+ }
+ } else {
+ pr_err("No NS16550a UART found!");
+ return -ENODEV;
+ }
+
+ s = strstr(arcs_cmdline, "console=ttyS0,");
+ if (s) {
+ s += 14;
+ baud = kstrtoul(s, 10, &baud);
+ if (err)
+ baud = 0;
+ while (isdigit(*s))
+ s++;
+ if (*s == ',')
+ s++;
+ if (*s)
+ parity = *s++;
+ if (*s == ',')
+ s++;
+ if (*s)
+ bits = *s++;
+ if (*s == ',')
+ s++;
+ if (*s == 'h')
+ flow = 'r';
+ }
+
+ if (baud == 0) {
+ baud = 38400;
+ pr_warn("Using default baud rate: %lu\n", baud);
+ }
+ if (parity != 'n' && parity != 'o' && parity != 'e')
+ parity = 'n';
+ if (bits != '7' && bits != '8')
+ bits = '8';
+
+ memset(&p, 0, sizeof(p));
+
+ p.type = PORT_16550A;
+ p.membase = (unsigned char *) RTL838X_UART0_BASE;
+ p.irq = RTL838X_UART0_IRQ;
+ p.uartclk = SYSTEM_FREQ - (24 * baud);
+ p.flags = UPF_SKIP_TEST | UPF_LOW_LATENCY | UPF_FIXED_TYPE;
+ p.iotype = UPIO_MEM;
+ p.regshift = 2;
+ p.fifosize = 1;
+
+ /* Call early_serial_setup() here, to set up 8250 console driver */
+ if (early_serial_setup(&p) != 0)
+ ret = 1;
+#endif
+ return 0;
+}
diff --git a/target/linux/rtl838x/files-5.4/arch/mips/rtl838x/setup.c b/target/linux/rtl838x/files-5.4/arch/mips/rtl838x/setup.c
new file mode 100644
index 0000000000..6a9485c451
--- /dev/null
+++ b/target/linux/rtl838x/files-5.4/arch/mips/rtl838x/setup.c
@@ -0,0 +1,187 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Setup for the Realtek RTL838X SoC:
+ * Memory, Timer and Serial
+ *
+ * Copyright (C) 2020 B. Koblitz
+ * based on the original BSP by
+ * Copyright (C) 2006-2012 Tony Wu (tonywu at realtek.com)
+ *
+ */
+#include <linux/console.h>
+#include <linux/init.h>
+#include <linux/clk.h>
+#include <linux/clkdev.h>
+#include <linux/clk-provider.h>
+
+#include <asm/addrspace.h>
+#include <asm/io.h>
+
+#include <asm/bootinfo.h>
+#include <linux/of_fdt.h>
+#include <asm/reboot.h>
+#include <asm/time.h> /* for mips_hpt_frequency */
+#include <asm/prom.h>
+#include <asm/smp-ops.h>
+
+#include "mach-rtl838x.h"
+
+extern int rtl838x_serial_init(void);
+extern struct rtl838x_soc_info soc_info;
+
+struct clk {
+ struct clk_lookup cl;
+ unsigned long rate;
+};
+
+struct clk cpu_clk;
+
+u32 pll_reset_value;
+
+static void rtl838x_restart(char *command)
+{
+ u32 pll = sw_r32(RTL838X_PLL_CML_CTRL);
+ /* SoC reset vector (in flash memory): on RTL839x platform preferred way to reset */
+ void (*f)(void) = (void *) 0xbfc00000;
+
+ pr_info("System restart.\n");
+ if (soc_info.family == RTL8390_FAMILY_ID) {
+ f();
+ /* If calling reset vector fails, reset entire chip */
+ sw_w32(0xFFFFFFFF, RTL839X_RST_GLB_CTRL);
+ /* If this fails, halt the CPU */
+ while
+ (1);
+ }
+
+ pr_info("PLL control register: %x, applying reset value %x\n",
+ pll, pll_reset_value);
+ sw_w32(3, RTL838X_INT_RW_CTRL);
+ sw_w32(pll_reset_value, RTL838X_PLL_CML_CTRL);
+ sw_w32(0, RTL838X_INT_RW_CTRL);
+
+ pr_info("Resetting RTL838X SoC\n");
+ /* Reset Global Control1 Register */
+ sw_w32(1, RTL838X_RST_GLB_CTRL_1);
+}
+
+static void rtl838x_halt(void)
+{
+ pr_info("System halted.\n");
+ while
+ (1);
+}
+
+static void __init rtl838x_setup(void)
+{
+ unsigned int val;
+
+ pr_info("Registering _machine_restart\n");
+ _machine_restart = rtl838x_restart;
+ _machine_halt = rtl838x_halt;
+
+ val = rtl838x_r32((volatile void *)0xBB0040000);
+ if (val == 3)
+ pr_info("PCI device found\n");
+ else
+ pr_info("NO PCI device found\n");
+
+ /* Setup System LED. Bit 15 (14 for RTL8390) then allows to toggle it */
+ if (soc_info.family == RTL8380_FAMILY_ID)
+ sw_w32_mask(0, 3 << 16, RTL838X_LED_GLB_CTRL);
+ else
+ sw_w32_mask(0, 3 << 15, RTL839X_LED_GLB_CTRL);
+}
+
+void __init plat_mem_setup(void)
+{
+ void *dtb;
+
+ pr_info("%s called\n", __func__);
+
+ set_io_port_base(KSEG1);
+
+ if (fw_passed_dtb) /* UHI interface */
+ dtb = (void *)fw_passed_dtb;
+ else if (__dtb_start != __dtb_end)
+ dtb = (void *)__dtb_start;
+ else
+ panic("no dtb found");
+
+ /*
+ * Load the devicetree. This causes the chosen node to be
+ * parsed resulting in our memory appearing
+ */
+ __dt_setup_arch(dtb);
+
+ rtl838x_setup();
+}
+
+
+/*
+ * Linux clock API
+ */
+int clk_enable(struct clk *clk)
+{
+ return 0;
+}
+EXPORT_SYMBOL_GPL(clk_enable);
+
+void clk_disable(struct clk *clk)
+{
+
+}
+EXPORT_SYMBOL_GPL(clk_disable);
+
+unsigned long clk_get_rate(struct clk *clk)
+{
+ if (!clk)
+ return 0;
+
+ return clk->rate;
+}
+EXPORT_SYMBOL_GPL(clk_get_rate);
+
+int clk_set_rate(struct clk *clk, unsigned long rate)
+{
+ return -1;
+}
+EXPORT_SYMBOL_GPL(clk_set_rate);
+
+long clk_round_rate(struct clk *clk, unsigned long rate)
+{
+ return -1;
+}
+EXPORT_SYMBOL_GPL(clk_round_rate);
+
+void __init plat_time_init(void)
+{
+ u32 freq = 500000000;
+ struct device_node *np;
+ struct clk *clk = &cpu_clk;
+
+ np = of_find_node_by_name(NULL, "cpus");
+ if (!np) {
+ pr_err("Missing 'cpus' DT node, using default frequency.");
+ } else {
+ if (of_property_read_u32(np, "frequency", &freq) < 0)
+ pr_err("No 'frequency' property in DT, using default.");
+ else
+ pr_info("CPU frequency from device tree: %d", freq);
+ of_node_put(np);
+ }
+
+ clk->rate = freq;
+
+ if (IS_ERR(clk))
+ panic("unable to get CPU clock, err=%ld", PTR_ERR(clk));
+
+ pr_info("CPU Clock: %ld MHz\n", clk->rate / 1000000);
+ mips_hpt_frequency = freq / 2;
+
+ pll_reset_value = sw_r32(RTL838X_PLL_CML_CTRL);
+ pr_info("PLL control register: %x\n", pll_reset_value);
+
+ /* With the info from the command line and cpu-freq we can setup the console */
+ rtl838x_serial_init();
+}
diff --git a/target/linux/rtl838x/files-5.4/drivers/gpio/gpio-rtl838x.c b/target/linux/rtl838x/files-5.4/drivers/gpio/gpio-rtl838x.c
new file mode 100644
index 0000000000..bba3b3f572
--- /dev/null
+++ b/target/linux/rtl838x/files-5.4/drivers/gpio/gpio-rtl838x.c
@@ -0,0 +1,807 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include <linux/gpio/driver.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <asm/mach-rtl838x/mach-rtl838x.h>
+
+/* RTL8231 registers for LED control */
+#define RTL8231_LED_FUNC0 0x0000
+#define RTL8231_GPIO_PIN_SEL(gpio) ((0x0002) + ((gpio) >> 4))
+#define RTL8231_GPIO_DIR(gpio) ((0x0005) + ((gpio) >> 4))
+#define RTL8231_GPIO_DATA(gpio) ((0x001C) + ((gpio) >> 4))
+#define RTL8231_GPIO_PIN_SEL0 0x0002
+#define RTL8231_GPIO_PIN_SEL1 0x0003
+#define RTL8231_GPIO_PIN_SEL2 0x0004
+#define RTL8231_GPIO_IO_SEL0 0x0005
+#define RTL8231_GPIO_IO_SEL1 0x0006
+#define RTL8231_GPIO_IO_SEL2 0x0007
+
+#define MDC_WAIT { int i; for (i = 0; i < 2; i++); }
+#define I2C_WAIT { int i; for (i = 0; i < 5; i++); }
+
+struct rtl838x_gpios {
+ struct gpio_chip gc;
+ u32 id;
+ struct device *dev;
+ int irq;
+ int bus_id;
+ int num_leds;
+ int min_led;
+ int leds_per_port;
+ u32 led_mode;
+ u16 rtl8381_phy_id;
+ int smi_clock;
+ int smi_data;
+ int i2c_sda;
+ int i2c_sdc;
+};
+
+extern struct mutex smi_lock;
+
+u32 rtl838x_rtl8231_read(u8 bus_id, u32 reg)
+{
+ u32 t = 0;
+
+ reg &= 0x1f;
+ bus_id &= 0x1f;
+
+ /* Calculate read register address */
+ t = (bus_id << 2) | (reg << 7);
+
+ mutex_lock(&smi_lock);
+ /* Set execution bit: cleared when operation completed */
+ t |= 1;
+ sw_w32(t, RTL838X_EXT_GPIO_INDRT_ACCESS);
+ do { /* TODO: Return 0x80000000 if timeout */
+ t = sw_r32(RTL838X_EXT_GPIO_INDRT_ACCESS);
+ } while (t & 1);
+ pr_debug("%s: %x, %x, %x\n", __func__, bus_id, reg, (t & 0xffff0000) >> 16);
+
+ mutex_unlock(&smi_lock);
+ return (t & 0xffff0000) >> 16;
+}
+
+int rtl838x_rtl8231_write(u8 bus_id, u32 reg, u32 data)
+{
+ u32 t = 0;
+
+ pr_debug("%s: %x, %x, %x\n", __func__, bus_id, reg, data);
+ data &= 0xffff;
+ reg &= 0x1f;
+ bus_id &= 0x1f;
+
+ mutex_lock(&smi_lock);
+ t = (bus_id << 2) | (reg << 7) | (data << 16);
+ /* Set write bit */
+ t |= 2;
+
+ /* Set execution bit: cleared when operation completed */
+ t |= 1;
+ sw_w32(t, RTL838X_EXT_GPIO_INDRT_ACCESS);
+ do { /* TODO: Return -1 if timeout */
+ t = sw_r32(RTL838X_EXT_GPIO_INDRT_ACCESS);
+ } while (t & 1);
+
+ mutex_unlock(&smi_lock);
+ return 0;
+}
+
+static int rtl8231_pin_dir(u8 bus_id, u32 gpio, u32 dir)
+{
+ /* dir 1: input
+ * dir 0: output
+ */
+
+ u32 v;
+ int pin_sel_addr = RTL8231_GPIO_PIN_SEL(gpio);
+ int pin_dir_addr = RTL8231_GPIO_DIR(gpio);
+ int pin = gpio % 16;
+ int dpin = pin;
+
+ if (gpio > 31) {
+ dpin = pin << 5;
+ pin_dir_addr = pin_sel_addr;
+ }
+
+ /* Select GPIO function for pin */
+ v = rtl838x_rtl8231_read(bus_id, pin_sel_addr);
+ if (v & 0x80000000) {
+ pr_err("Error reading RTL8231\n");
+ return -1;
+ }
+ rtl838x_rtl8231_write(bus_id, pin_sel_addr, v | (1 << pin));
+
+ v = rtl838x_rtl8231_read(bus_id, pin_dir_addr);
+ if (v & 0x80000000) {
+ pr_err("Error reading RTL8231\n");
+ return -1;
+ }
+ rtl838x_rtl8231_write(bus_id, pin_dir_addr,
+ (v & ~(1 << dpin)) | (dir << dpin));
+ return 0;
+}
+
+static int rtl8231_pin_dir_get(u8 bus_id, u32 gpio, u32 *dir)
+{
+ /* dir 1: input
+ * dir 0: output
+ */
+
+ u32 v;
+ int pin_dir_addr = RTL8231_GPIO_DIR(gpio);
+ int pin = gpio % 16;
+
+ if (gpio > 31) {
+ pin_dir_addr = RTL8231_GPIO_PIN_SEL(gpio);
+ pin = pin << 5;
+ }
+
+ v = rtl838x_rtl8231_read(bus_id, pin_dir_addr);
+ if (v & (1 << pin))
+ *dir = 1;
+ else
+ *dir = 0;
+ return 0;
+}
+
+static int rtl8231_pin_set(u8 bus_id, u32 gpio, u32 data)
+{
+ u32 v = rtl838x_rtl8231_read(bus_id, RTL8231_GPIO_DATA(gpio));
+
+ if (v & 0x80000000) {
+ pr_err("Error reading RTL8231\n");
+ return -1;
+ }
+ rtl838x_rtl8231_write(bus_id, RTL8231_GPIO_DATA(gpio),
+ (v & ~(1 << (gpio % 16))) | (data << (gpio % 16)));
+ return 0;
+}
+
+static int rtl8231_pin_get(u8 bus_id, u32 gpio, u16 *state)
+{
+ u32 v = rtl838x_rtl8231_read(bus_id, RTL8231_GPIO_DATA(gpio));
+
+ if (v & 0x80000000) {
+ pr_err("Error reading RTL8231\n");
+ return -1;
+ }
+
+ *state = v & 0xffff;
+ return 0;
+}
+
+static int rtl838x_direction_input(struct gpio_chip *gc, unsigned int offset)
+{
+ struct rtl838x_gpios *gpios = gpiochip_get_data(gc);
+
+ pr_debug("%s: %d\n", __func__, offset);
+
+ if (offset < 32) {
+ rtl838x_w32_mask(1 << offset, 0, RTL838X_GPIO_PABC_DIR);
+ return 0;
+ }
+
+ /* Internal LED driver does not support input */
+ if (offset >= 32 && offset < 64)
+ return -ENOTSUPP;
+
+ if (offset >= 64 && offset < 100 && gpios->bus_id >= 0)
+ return rtl8231_pin_dir(gpios->bus_id, offset - 64, 1);
+
+ return -ENOTSUPP;
+}
+
+static int rtl838x_direction_output(struct gpio_chip *gc, unsigned int offset, int value)
+{
+ struct rtl838x_gpios *gpios = gpiochip_get_data(gc);
+
+ pr_debug("%s: %d\n", __func__, offset);
+ if (offset < 32)
+ rtl838x_w32_mask(0, 1 << offset, RTL838X_GPIO_PABC_DIR);
+
+ /* LED for PWR and SYS driver is direction output by default */
+ if (offset >= 32 && offset < 64)
+ return 0;
+
+ if (offset >= 64 && offset < 100 && gpios->bus_id >= 0)
+ return rtl8231_pin_dir(gpios->bus_id, offset - 64, 0);
+ return 0;
+}
+
+static int rtl838x_get_direction(struct gpio_chip *gc, unsigned int offset)
+{
+ u32 v = 0;
+ struct rtl838x_gpios *gpios = gpiochip_get_data(gc);
+
+ pr_debug("%s: %d\n", __func__, offset);
+ if (offset < 32) {
+ v = rtl838x_r32(RTL838X_GPIO_PABC_DIR);
+ if (v & (1 << offset))
+ return 0;
+ return 1;
+ }
+
+ /* LED driver for PWR and SYS is direction output by default */
+ if (offset >= 32 && offset < 64)
+ return 0;
+
+ if (offset >= 64 && offset < 100 && gpios->bus_id >= 0) {
+ rtl8231_pin_dir_get(gpios->bus_id, offset - 64, &v);
+ return v;
+ }
+
+ return 0;
+}
+
+static int rtl838x_gpio_get(struct gpio_chip *gc, unsigned int offset)
+{
+ u32 v;
+ u16 state = 0;
+ int bit;
+ struct rtl838x_gpios *gpios = gpiochip_get_data(gc);
+
+ pr_debug("%s: %d\n", __func__, offset);
+
+ /* Internal GPIO of the RTL8380 */
+ if (offset < 32) {
+ v = rtl838x_r32(RTL838X_GPIO_PABC_DATA);
+ if (v & (1 << offset))
+ return 1;
+ return 0;
+ }
+
+ /* LED driver for PWR and SYS */
+ if (offset >= 32 && offset < 64) {
+ v = sw_r32(RTL838X_LED_GLB_CTRL);
+ if (v & (1 << (offset-32)))
+ return 1;
+ return 0;
+ }
+
+ /* Indirect access GPIO with RTL8231 */
+ if (offset >= 64 && offset < 100 && gpios->bus_id >= 0) {
+ rtl8231_pin_get(gpios->bus_id, offset - 64, &state);
+ if (state & (1 << (offset % 16)))
+ return 1;
+ return 0;
+ }
+
+ bit = (offset - 100) % 32;
+ if (offset >= 100 && offset < 132) {
+ if (sw_r32(RTL838X_LED1_SW_P_EN_CTRL) & (1 << bit))
+ return 1;
+ return 0;
+ }
+ if (offset >= 132 && offset < 164) {
+ if (sw_r32(RTL838X_LED1_SW_P_EN_CTRL) & (1 << bit))
+ return 1;
+ return 0;
+ }
+ if (offset >= 164 && offset < 196) {
+ if (sw_r32(RTL838X_LED1_SW_P_EN_CTRL) & (1 << bit))
+ return 1;
+ return 0;
+ }
+ return 0;
+}
+
+void rtl838x_gpio_set(struct gpio_chip *gc, unsigned int offset, int value)
+{
+ int bit;
+ struct rtl838x_gpios *gpios = gpiochip_get_data(gc);
+
+ pr_debug("rtl838x_set: %d, value: %d\n", offset, value);
+ /* Internal GPIO of the RTL8380 */
+ if (offset < 32) {
+ if (value)
+ rtl838x_w32_mask(0, 1 << offset, RTL838X_GPIO_PABC_DATA);
+ else
+ rtl838x_w32_mask(1 << offset, 0, RTL838X_GPIO_PABC_DATA);
+ }
+
+ /* LED driver for PWR and SYS */
+ if (offset >= 32 && offset < 64) {
+ bit = offset - 32;
+ if (value)
+ sw_w32_mask(0, 1 << bit, RTL838X_LED_GLB_CTRL);
+ else
+ sw_w32_mask(1 << bit, 0, RTL838X_LED_GLB_CTRL);
+ return;
+ }
+
+ /* Indirect access GPIO with RTL8231 */
+ if (offset >= 64 && offset < 100 && gpios->bus_id >= 0) {
+ rtl8231_pin_set(gpios->bus_id, offset - 64, value);
+ return;
+ }
+
+ bit = (offset - 100) % 32;
+ /* First Port-LED */
+ if (offset >= 100 && offset < 132
+ && offset >= (100 + gpios->min_led)
+ && offset < (100 + gpios->min_led + gpios->num_leds)) {
+ if (value)
+ sw_w32_mask(7, 5, RTL838X_LED_SW_P_CTRL(bit));
+ else
+ sw_w32_mask(7, 0, RTL838X_LED_SW_P_CTRL(bit));
+ }
+ if (offset >= 132 && offset < 164
+ && offset >= (132 + gpios->min_led)
+ && offset < (132 + gpios->min_led + gpios->num_leds)) {
+ if (value)
+ sw_w32_mask(7 << 3, 5 << 3, RTL838X_LED_SW_P_CTRL(bit));
+ else
+ sw_w32_mask(7 << 3, 0, RTL838X_LED_SW_P_CTRL(bit));
+ }
+ if (offset >= 164 && offset < 196
+ && offset >= (164 + gpios->min_led)
+ && offset < (164 + gpios->min_led + gpios->num_leds)) {
+ if (value)
+ sw_w32_mask(7 << 6, 5 << 6, RTL838X_LED_SW_P_CTRL(bit));
+ else
+ sw_w32_mask(7 << 6, 0, RTL838X_LED_SW_P_CTRL(bit));
+ }
+ __asm__ volatile ("sync");
+}
+
+int rtl8231_init(struct rtl838x_gpios *gpios)
+{
+ uint32_t v;
+ u8 bus_id = gpios->bus_id;
+
+ pr_info("%s called\n", __func__);
+
+ /* Enable RTL8231 indirect access mode */
+ sw_w32_mask(0, 1, RTL838X_EXTRA_GPIO_CTRL);
+ sw_w32_mask(3, 1, RTL838X_DMY_REG5);
+
+ /* Enable RTL8231 via GPIO_A1 line */
+ rtl838x_w32_mask(0, 1 << RTL838X_GPIO_A1, RTL838X_GPIO_PABC_DIR);
+ rtl838x_w32_mask(0, 1 << RTL838X_GPIO_A1, RTL838X_GPIO_PABC_DATA);
+ mdelay(50); /* wait 50ms for reset */
+
+ /*Select GPIO functionality for pins 0-15, 16-31 and 32-37 */
+ rtl838x_rtl8231_write(bus_id, RTL8231_GPIO_PIN_SEL(0), 0xffff);
+ rtl838x_rtl8231_write(bus_id, RTL8231_GPIO_PIN_SEL(16), 0xffff);
+ rtl838x_rtl8231_write(bus_id, RTL8231_GPIO_PIN_SEL2, 0x03ff);
+
+ v = rtl838x_rtl8231_read(bus_id, RTL8231_LED_FUNC0);
+ pr_info("RTL8231 led function now: %x\n", v);
+
+ return 0;
+}
+
+static void smi_write_bit(struct rtl838x_gpios *gpios, u32 bit)
+{
+ if (bit)
+ rtl838x_w32_mask(0, 1 << gpios->smi_data, RTL838X_GPIO_PABC_DATA);
+ else
+ rtl838x_w32_mask(1 << gpios->smi_data, 0, RTL838X_GPIO_PABC_DATA);
+
+ MDC_WAIT;
+ rtl838x_w32_mask(1 << gpios->smi_clock, 0, RTL838X_GPIO_PABC_DATA);
+ MDC_WAIT;
+ rtl838x_w32_mask(0, 1 << gpios->smi_clock, RTL838X_GPIO_PABC_DATA);
+}
+
+static int smi_read_bit(struct rtl838x_gpios *gpios)
+{
+ u32 v;
+
+ MDC_WAIT;
+ rtl838x_w32_mask(1 << gpios->smi_clock, 0, RTL838X_GPIO_PABC_DATA);
+ MDC_WAIT;
+ rtl838x_w32_mask(0, 1 << gpios->smi_clock, RTL838X_GPIO_PABC_DATA);
+
+ v = rtl838x_r32(RTL838X_GPIO_PABC_DATA);
+ if (v & (1 << gpios->smi_data))
+ return 1;
+ return 0;
+}
+
+/* Tri-state of MDIO line */
+static void smi_z(struct rtl838x_gpios *gpios)
+{
+ /* MDIO pin to input */
+ rtl838x_w32_mask(1 << gpios->smi_data, 0, RTL838X_GPIO_PABC_DIR);
+ MDC_WAIT;
+ rtl838x_w32_mask(1 << gpios->smi_clock, 0, RTL838X_GPIO_PABC_DATA);
+ MDC_WAIT;
+ rtl838x_w32_mask(0, 1 << gpios->smi_clock, RTL838X_GPIO_PABC_DATA);
+}
+
+static void smi_write_bits(struct rtl838x_gpios *gpios, u32 data, int len)
+{
+ while (len) {
+ len--;
+ smi_write_bit(gpios, data & (1 << len));
+ }
+}
+
+static void smi_read_bits(struct rtl838x_gpios *gpios, int len, u32 *data)
+{
+ u32 v = 0;
+
+ while (len) {
+ len--;
+ v <<= 1;
+ v |= smi_read_bit(gpios);
+ }
+ *data = v;
+}
+
+/* Bit-banged verson of SMI write access, caller must hold smi_lock */
+int rtl8380_smi_write(struct rtl838x_gpios *gpios, u16 reg, u32 data)
+{
+ u16 bus_id = gpios->bus_id;
+
+ /* Set clock and data pins on RTL838X to output */
+ rtl838x_w32_mask(0, 1 << gpios->smi_clock, RTL838X_GPIO_PABC_DIR);
+ rtl838x_w32_mask(0, 1 << gpios->smi_data, RTL838X_GPIO_PABC_DIR);
+
+ /* Write start bits */
+ smi_write_bits(gpios, 0xffffffff, 32);
+
+ smi_write_bits(gpios, 0x5, 4); /* ST and write OP */
+
+ smi_write_bits(gpios, bus_id, 5); /* 5 bits: phy address */
+ smi_write_bits(gpios, reg, 5); /* 5 bits: register address */
+
+ smi_write_bits(gpios, 0x2, 2); /* TURNAROUND */
+
+ smi_write_bits(gpios, data, 16); /* 16 bits: data*/
+
+ smi_z(gpios);
+
+ return 0;
+}
+
+/* Bit-banged verson of SMI read access, caller must hold smi_lock */
+int rtl8380_smi_read(struct rtl838x_gpios *gpios, u16 reg, u32 *data)
+{
+ u16 bus_id = gpios->bus_id;
+
+ /* Set clock and data pins on RTL838X to output */
+ rtl838x_w32_mask(0, 1 << gpios->smi_clock, RTL838X_GPIO_PABC_DIR);
+ rtl838x_w32_mask(0, 1 << gpios->smi_data, RTL838X_GPIO_PABC_DIR);
+
+ /* Write start bits */
+ smi_write_bits(gpios, 0xffffffff, 32);
+
+ smi_write_bits(gpios, 0x6, 4); /* ST and read OP */
+
+ smi_write_bits(gpios, bus_id, 5); /* 5 bits: phy address */
+ smi_write_bits(gpios, reg, 5); /* 5 bits: register address */
+
+ smi_z(gpios); /* TURNAROUND */
+
+ smi_read_bits(gpios, 16, data);
+ return 0;
+}
+
+static void i2c_pin_set(struct rtl838x_gpios *gpios, int pin, u32 data)
+{
+ u32 v;
+
+ rtl8380_smi_read(gpios, RTL8231_GPIO_DATA(pin), &v);
+ if (!data)
+ v &= ~(1 << (pin % 16));
+ else
+ v |= (1 << (pin % 16));
+ rtl8380_smi_write(gpios, RTL8231_GPIO_DATA(pin), v);
+}
+
+static void i2c_pin_get(struct rtl838x_gpios *gpios, int pin, u32 *data)
+{
+ u32 v;
+
+ rtl8380_smi_read(gpios, RTL8231_GPIO_DATA(pin), &v);
+ if (v & (1 << (pin % 16))) {
+ *data = 1;
+ return;
+ }
+ *data = 0;
+}
+
+static void i2c_pin_dir(struct rtl838x_gpios *gpios, int pin, u16 direction)
+{
+ u32 v;
+
+ rtl8380_smi_read(gpios, RTL8231_GPIO_DIR(pin), &v);
+ if (direction) // Output
+ v &= ~(1 << (pin % 16));
+ else
+ v |= (1 << (pin % 16));
+ rtl8380_smi_write(gpios, RTL8231_GPIO_DIR(pin), v);
+}
+
+static void i2c_start(struct rtl838x_gpios *gpios)
+{
+ i2c_pin_dir(gpios, gpios->i2c_sda, 0); /* Output */
+ i2c_pin_dir(gpios, gpios->i2c_sdc, 0); /* Output */
+ I2C_WAIT;
+ i2c_pin_set(gpios, gpios->i2c_sdc, 1);
+ I2C_WAIT;
+ i2c_pin_set(gpios, gpios->i2c_sda, 1);
+ I2C_WAIT;
+ i2c_pin_set(gpios, gpios->i2c_sda, 0);
+ I2C_WAIT;
+ i2c_pin_set(gpios, gpios->i2c_sdc, 0);
+ I2C_WAIT;
+}
+
+static void i2c_stop(struct rtl838x_gpios *gpios)
+{
+ I2C_WAIT;
+ i2c_pin_set(gpios, gpios->i2c_sdc, 1);
+ i2c_pin_set(gpios, gpios->i2c_sda, 0);
+ I2C_WAIT;
+
+ i2c_pin_set(gpios, gpios->i2c_sda, 1);
+ I2C_WAIT;
+ i2c_pin_set(gpios, gpios->i2c_sdc, 0);
+
+ i2c_pin_dir(gpios, gpios->i2c_sda, 1); /* Input */
+ i2c_pin_dir(gpios, gpios->i2c_sdc, 1); /* Input */
+}
+
+static void i2c_read_bits(struct rtl838x_gpios *gpios, int len, u32 *data)
+{
+ u32 v = 0, t;
+
+ while (len) {
+ len--;
+ v <<= 1;
+ i2c_pin_set(gpios, gpios->i2c_sdc, 1);
+ I2C_WAIT;
+ i2c_pin_get(gpios, gpios->i2c_sda, &t);
+ v |= t;
+ i2c_pin_set(gpios, gpios->i2c_sdc, 0);
+ I2C_WAIT;
+ }
+ *data = v;
+}
+
+static void i2c_write_bits(struct rtl838x_gpios *gpios, u32 data, int len)
+{
+ while (len) {
+ len--;
+ i2c_pin_set(gpios, gpios->i2c_sda, data & (1 << len));
+ I2C_WAIT;
+ i2c_pin_set(gpios, gpios->i2c_sdc, 1);
+ I2C_WAIT;
+ i2c_pin_set(gpios, gpios->i2c_sdc, 0);
+ I2C_WAIT;
+ }
+}
+
+/* This initializes direct external GPIOs via the RTL8231 */
+int rtl8380_rtl8321_init(struct rtl838x_gpios *gpios)
+{
+ u32 v;
+ int mdc = gpios->smi_clock;
+ int mdio = gpios->smi_data;
+
+ pr_info("Configuring SMI: Clock %d, Data %d\n", mdc, mdio);
+ sw_w32_mask(0, 0x2, RTL838X_IO_DRIVING_ABILITY_CTRL);
+
+ /* Enter simulated GPIO mode */
+ sw_w32_mask(1, 0, RTL838X_EXTRA_GPIO_CTRL);
+
+ /* MDIO clock to 2.6MHz */
+ sw_w32_mask(0x3 << 8, 0, RTL838X_EXTRA_GPIO_CTRL);
+
+ /* Configure SMI clock and data GPIO pins */
+ rtl838x_w32_mask((1 << mdc) | (1 << mdio), 0, RTL838X_GPIO_PABC_CNR);
+ rtl838x_w32_mask(0, (1 << mdc) | (1 << mdio), RTL838X_GPIO_PABC_DIR);
+
+ rtl8380_smi_write(gpios, RTL8231_GPIO_PIN_SEL0, 0xffff);
+ rtl8380_smi_write(gpios, RTL8231_GPIO_PIN_SEL1, 0xffff);
+ rtl8380_smi_read(gpios, RTL8231_GPIO_PIN_SEL2, &v);
+ v |= 0x1f;
+ rtl8380_smi_write(gpios, RTL8231_GPIO_PIN_SEL2, v);
+
+ rtl8380_smi_write(gpios, RTL8231_GPIO_IO_SEL0, 0xffff);
+ rtl8380_smi_write(gpios, RTL8231_GPIO_IO_SEL1, 0xffff);
+ rtl8380_smi_read(gpios, RTL8231_GPIO_IO_SEL2, &v);
+ v |= 0x1f << 5;
+ rtl8380_smi_write(gpios, RTL8231_GPIO_PIN_SEL2, v);
+
+ return 0;
+}
+
+void rtl8380_led_test(u32 mask)
+{
+ int i;
+ u32 mode_sel = sw_r32(RTL838X_LED_MODE_SEL);
+ u32 led_gbl = sw_r32(RTL838X_LED_GLB_CTRL);
+ u32 led_p_en = sw_r32(RTL838X_LED_P_EN_CTRL);
+
+ /* 2 Leds for ports 0-23 and 24-27, 3 would be 0x7 */
+ sw_w32_mask(0x3f, 0x3 | (0x3 << 3), RTL838X_LED_GLB_CTRL);
+ /* Enable all leds */
+ sw_w32(0xFFFFFFF, RTL838X_LED_P_EN_CTRL);
+
+ /* Enable software control of all leds */
+ sw_w32(0xFFFFFFF, RTL838X_LED_SW_CTRL);
+ sw_w32(0xFFFFFFF, RTL838X_LED0_SW_P_EN_CTRL);
+ sw_w32(0xFFFFFFF, RTL838X_LED1_SW_P_EN_CTRL);
+ sw_w32(0x0000000, RTL838X_LED2_SW_P_EN_CTRL);
+
+ for (i = 0; i < 28; i++) {
+ if (mask & (1 << i))
+ sw_w32(5 | (5 << 3) | (5 << 6),
+ RTL838X_LED_SW_P_CTRL(i));
+ }
+ msleep(3000);
+
+ sw_w32(led_p_en, RTL838X_LED_P_EN_CTRL);
+ /* Disable software control of all leds */
+ sw_w32(0x0000000, RTL838X_LED_SW_CTRL);
+ sw_w32(0x0000000, RTL838X_LED0_SW_P_EN_CTRL);
+ sw_w32(0x0000000, RTL838X_LED1_SW_P_EN_CTRL);
+ sw_w32(0x0000000, RTL838X_LED2_SW_P_EN_CTRL);
+
+ sw_w32(led_gbl, RTL838X_LED_GLB_CTRL);
+ sw_w32(mode_sel, RTL838X_LED_MODE_SEL);
+}
+
+void take_port_leds(struct rtl838x_gpios *gpios)
+{
+ int leds_per_port = gpios->leds_per_port;
+ int mode = gpios->led_mode;
+
+ pr_info("%s, %d, %x\n", __func__, leds_per_port, mode);
+ pr_debug("Bootloader settings: %x %x %x\n",
+ sw_r32(RTL838X_LED0_SW_P_EN_CTRL),
+ sw_r32(RTL838X_LED1_SW_P_EN_CTRL),
+ sw_r32(RTL838X_LED2_SW_P_EN_CTRL)
+ );
+
+ pr_debug("led glb: %x, sel %x\n",
+ sw_r32(RTL838X_LED_GLB_CTRL), sw_r32(RTL838X_LED_MODE_SEL));
+ pr_debug("RTL838X_LED_P_EN_CTRL: %x", sw_r32(RTL838X_LED_P_EN_CTRL));
+ pr_debug("RTL838X_LED_MODE_CTRL: %x", sw_r32(RTL838X_LED_MODE_CTRL));
+
+ sw_w32_mask(3, 0, RTL838X_LED_MODE_SEL);
+ sw_w32(mode, RTL838X_LED_MODE_CTRL);
+
+ /* Enable software control of all leds */
+ sw_w32(0xFFFFFFF, RTL838X_LED_SW_CTRL);
+ sw_w32(0xFFFFFFF, RTL838X_LED_P_EN_CTRL);
+
+ sw_w32(0x0000000, RTL838X_LED0_SW_P_EN_CTRL);
+ sw_w32(0x0000000, RTL838X_LED1_SW_P_EN_CTRL);
+ sw_w32(0x0000000, RTL838X_LED2_SW_P_EN_CTRL);
+
+ sw_w32_mask(0x3f, 0, RTL838X_LED_GLB_CTRL);
+ switch (leds_per_port) {
+ case 3:
+ sw_w32_mask(0, 0x7 | (0x7 << 3), RTL838X_LED_GLB_CTRL);
+ sw_w32(0xFFFFFFF, RTL838X_LED2_SW_P_EN_CTRL);
+ /* FALLTHRU */
+ case 2:
+ sw_w32_mask(0, 0x3 | (0x3 << 3), RTL838X_LED_GLB_CTRL);
+ sw_w32(0xFFFFFFF, RTL838X_LED1_SW_P_EN_CTRL);
+ /* FALLTHRU */
+ case 1:
+ sw_w32_mask(0, 0x1 | (0x1 << 3), RTL838X_LED_GLB_CTRL);
+ sw_w32(0xFFFFFFF, RTL838X_LED0_SW_P_EN_CTRL);
+ break;
+ default:
+ pr_err("No LEDS configured for software control\n");
+ }
+}
+
+static const struct of_device_id rtl838x_gpio_of_match[] = {
+ { .compatible = "realtek,rtl838x-gpio" },
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, rtl838x_gpio_of_match);
+
+static int rtl838x_gpio_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ struct rtl838x_gpios *gpios;
+ int err;
+ u8 indirect_bus_id;
+
+ pr_info("Probing RTL838X GPIOs\n");
+
+ if (!np) {
+ dev_err(&pdev->dev, "No DT found\n");
+ return -EINVAL;
+ }
+
+ gpios = devm_kzalloc(dev, sizeof(*gpios), GFP_KERNEL);
+ if (!gpios)
+ return -ENOMEM;
+
+ gpios->id = sw_r32(RTL838X_MODEL_NAME_INFO) >> 16;
+
+ switch (gpios->id) {
+ case 0x8332:
+ pr_debug("Found RTL8332M GPIO\n");
+ break;
+ case 0x8380:
+ pr_debug("Found RTL8380M GPIO\n");
+ break;
+ case 0x8381:
+ pr_debug("Found RTL8381M GPIO\n");
+ break;
+ case 0x8382:
+ pr_debug("Found RTL8382M GPIO\n");
+ break;
+ default:
+ pr_err("Unknown GPIO chip id (%04x)\n", gpios->id);
+ return -ENODEV;
+ }
+
+ gpios->dev = dev;
+ gpios->gc.base = 0;
+ /* 0-31: internal
+ * 32-63, LED control register
+ * 64-99: external RTL8231
+ * 100-131: PORT-LED 0
+ * 132-163: PORT-LED 1
+ * 164-195: PORT-LED 2
+ */
+ gpios->gc.ngpio = 196;
+ gpios->gc.label = "rtl838x";
+ gpios->gc.parent = dev;
+ gpios->gc.owner = THIS_MODULE;
+ gpios->gc.can_sleep = true;
+ gpios->bus_id = -1;
+ gpios->irq = 31;
+
+ gpios->gc.direction_input = rtl838x_direction_input;
+ gpios->gc.direction_output = rtl838x_direction_output;
+ gpios->gc.set = rtl838x_gpio_set;
+ gpios->gc.get = rtl838x_gpio_get;
+ gpios->gc.get_direction = rtl838x_get_direction;
+
+ if (!of_property_read_u8(np, "indirect-access-bus-id", &indirect_bus_id)) {
+ gpios->bus_id = indirect_bus_id;
+ rtl8231_init(gpios);
+ }
+ if (!of_property_read_u8(np, "smi-bus-id", &indirect_bus_id)) {
+ gpios->bus_id = indirect_bus_id;
+ gpios->smi_clock = RTL838X_GPIO_A2;
+ gpios->smi_data = RTL838X_GPIO_A3;
+ gpios->i2c_sda = 1;
+ gpios->i2c_sdc = 2;
+ rtl8380_rtl8321_init(gpios);
+ }
+
+ if (of_property_read_bool(np, "take-port-leds")) {
+ if (of_property_read_u32(np, "leds-per-port", &gpios->leds_per_port))
+ gpios->leds_per_port = 2;
+ if (of_property_read_u32(np, "led-mode", &gpios->led_mode))
+ gpios->led_mode = (0x1ea << 15) | 0x1ea;
+ if (of_property_read_u32(np, "num-leds", &gpios->num_leds))
+ gpios->num_leds = 32;
+ if (of_property_read_u32(np, "min-led", &gpios->min_led))
+ gpios->min_led = 0;
+ take_port_leds(gpios);
+ }
+
+ err = devm_gpiochip_add_data(dev, &gpios->gc, gpios);
+ return err;
+}
+
+
+static struct platform_driver rtl838x_gpio_driver = {
+ .driver = {
+ .name = "rtl838x-gpio",
+ .of_match_table = rtl838x_gpio_of_match,
+ },
+ .probe = rtl838x_gpio_probe,
+};
+
+module_platform_driver(rtl838x_gpio_driver);
+
+MODULE_DESCRIPTION("Realtek RTL838X GPIO API support");
+MODULE_LICENSE("GPL v2");
diff --git a/target/linux/rtl838x/files-5.4/drivers/mtd/spi-nor/rtl838x-nor.c b/target/linux/rtl838x/files-5.4/drivers/mtd/spi-nor/rtl838x-nor.c
new file mode 100644
index 0000000000..0d8f9dbd3e
--- /dev/null
+++ b/target/linux/rtl838x/files-5.4/drivers/mtd/spi-nor/rtl838x-nor.c
@@ -0,0 +1,607 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/device.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/spi-nor.h>
+
+#include "rtl838x-spi.h"
+#include <asm/mach-rtl838x/mach-rtl838x.h>
+
+extern struct rtl838x_soc_info soc_info;
+
+struct rtl838x_nor {
+ struct spi_nor nor;
+ struct device *dev;
+ volatile void __iomem *base;
+ bool fourByteMode;
+ u32 chipSize;
+ uint32_t flags;
+ uint32_t io_status;
+};
+
+static uint32_t spi_prep(struct rtl838x_nor *rtl838x_nor)
+{
+ /* Needed because of MMU constraints */
+ SPI_WAIT_READY;
+ spi_w32w(SPI_CS_INIT, SFCSR); //deactivate CS0, CS1
+ spi_w32w(0, SFCSR); //activate CS0,CS1
+ spi_w32w(SPI_CS_INIT, SFCSR); //deactivate CS0, CS1
+
+ return (CS0 & rtl838x_nor->flags) ? (SPI_eCS0 & SPI_LEN_INIT)
+ : ((SPI_eCS1 & SPI_LEN_INIT) | SFCSR_CHIP_SEL);
+}
+
+static uint32_t rtl838x_nor_get_SR(struct rtl838x_nor *rtl838x_nor)
+{
+ uint32_t sfcsr, sfdr;
+
+ sfcsr = spi_prep(rtl838x_nor);
+ sfdr = (SPINOR_OP_RDSR)<<24;
+
+ pr_debug("%s: rdid,sfcsr_val = %.8x,SFDR = %.8x\n", __func__, sfcsr, sfdr);
+ pr_debug("rdid,sfcsr = %.8x\n", sfcsr | SPI_LEN4);
+ spi_w32w(sfcsr, SFCSR);
+ spi_w32w(sfdr, SFDR);
+ spi_w32_mask(0, SPI_LEN4, SFCSR);
+ SPI_WAIT_READY;
+
+ return spi_r32(SFDR);
+}
+
+static void spi_write_disable(struct rtl838x_nor *rtl838x_nor)
+{
+ uint32_t sfcsr, sfdr;
+
+ sfcsr = spi_prep(rtl838x_nor);
+ sfdr = (SPINOR_OP_WRDI) << 24;
+ spi_w32w(sfcsr, SFCSR);
+ spi_w32w(sfdr, SFDR);
+ pr_debug("%s: sfcsr_val = %.8x,SFDR = %.8x", __func__, sfcsr, sfdr);
+
+ spi_prep(rtl838x_nor);
+}
+
+static void spi_write_enable(struct rtl838x_nor *rtl838x_nor)
+{
+ uint32_t sfcsr, sfdr;
+
+ sfcsr = spi_prep(rtl838x_nor);
+ sfdr = (SPINOR_OP_WREN) << 24;
+ spi_w32w(sfcsr, SFCSR);
+ spi_w32w(sfdr, SFDR);
+ pr_debug("%s: sfcsr_val = %.8x,SFDR = %.8x", __func__, sfcsr, sfdr);
+
+ spi_prep(rtl838x_nor);
+}
+
+static void spi_4b_set(struct rtl838x_nor *rtl838x_nor, bool enable)
+{
+ uint32_t sfcsr, sfdr;
+
+ sfcsr = spi_prep(rtl838x_nor);
+ if (enable)
+ sfdr = (SPINOR_OP_EN4B) << 24;
+ else
+ sfdr = (SPINOR_OP_EX4B) << 24;
+
+ spi_w32w(sfcsr, SFCSR);
+ spi_w32w(sfdr, SFDR);
+ pr_debug("%s: sfcsr_val = %.8x,SFDR = %.8x", __func__, sfcsr, sfdr);
+
+ spi_prep(rtl838x_nor);
+}
+
+static int rtl838x_get_addr_mode(struct rtl838x_nor *rtl838x_nor)
+{
+ int res = 3;
+ u32 reg;
+
+ sw_w32(0x3, RTL838X_INT_RW_CTRL);
+ if (!sw_r32(RTL838X_EXT_VERSION)) {
+ if (sw_r32(RTL838X_STRAP_DBG) & (1 << 29))
+ res = 4;
+ } else {
+ reg = sw_r32(RTL838X_PLL_CML_CTRL);
+ if ((reg & (1 << 30)) && (reg & (1 << 31)))
+ res = 4;
+ if ((!(reg & (1 << 30)))
+ && sw_r32(RTL838X_STRAP_DBG) & (1 << 29))
+ res = 4;
+ }
+ sw_w32(0x0, RTL838X_INT_RW_CTRL);
+ return res;
+}
+
+static int rtl8390_get_addr_mode(struct rtl838x_nor *rtl838x_nor)
+{
+ if (spi_r32(RTL8390_SOC_SPI_MMIO_CONF) & (1 << 9))
+ return 4;
+ return 3;
+}
+
+ssize_t rtl838x_do_read(struct rtl838x_nor *rtl838x_nor, loff_t from,
+ size_t length, u_char *buffer, uint8_t command)
+{
+ uint32_t sfcsr, sfdr;
+ uint32_t len = length;
+
+ sfcsr = spi_prep(rtl838x_nor);
+ sfdr = command << 24;
+
+ /* Perform SPINOR_OP_READ: 1 byte command & 3 byte addr*/
+ sfcsr |= SPI_LEN4;
+ sfdr |= from;
+
+ spi_w32w(sfcsr, SFCSR);
+ spi_w32w(sfdr, SFDR);
+
+ /* Read Data, 4 bytes at a time */
+ while (length >= 4) {
+ SPI_WAIT_READY;
+ *((uint32_t *) buffer) = spi_r32(SFDR);
+/* printk("%.8x ", *((uint32_t*) buffer)); */
+ buffer += 4;
+ length -= 4;
+ }
+
+ /* The rest needs to be read 1 byte a time */
+ sfcsr &= SPI_LEN_INIT|SPI_LEN1;
+ SPI_WAIT_READY;
+ spi_w32w(sfcsr, SFCSR);
+ while (length > 0) {
+ SPI_WAIT_READY;
+ *(buffer) = spi_r32(SFDR) >> 24;
+/* printk("%.2x ", *(buffer)); */
+ buffer++;
+ length--;
+ }
+ return len;
+}
+
+/*
+ * Do fast read in 3 or 4 Byte addressing mode
+ */
+static ssize_t rtl838x_do_4bf_read(struct rtl838x_nor *rtl838x_nor, loff_t from,
+ size_t length, u_char *buffer, uint8_t command)
+{
+ int sfcsr_addr_len = rtl838x_nor->fourByteMode ? 0x3 : 0x2;
+ int sfdr_addr_shift = rtl838x_nor->fourByteMode ? 0 : 8;
+ uint32_t sfcsr;
+ uint32_t len = length;
+
+ pr_debug("Fast read from %llx, len %x, shift %d\n",
+ from, sfcsr_addr_len, sfdr_addr_shift);
+ sfcsr = spi_prep(rtl838x_nor);
+
+ /* Send read command */
+ spi_w32w(sfcsr | SPI_LEN1, SFCSR);
+ spi_w32w(command << 24, SFDR);
+
+ /* Send address */
+ spi_w32w(sfcsr | (sfcsr_addr_len << 28), SFCSR);
+ spi_w32w(from << sfdr_addr_shift, SFDR);
+
+ /* Dummy cycles */
+ spi_w32w(sfcsr | SPI_LEN1, SFCSR);
+ spi_w32w(0, SFDR);
+
+ /* Start reading */
+ spi_w32w(sfcsr | SPI_LEN4, SFCSR);
+
+ /* Read Data, 4 bytes at a time */
+ while (length >= 4) {
+ SPI_WAIT_READY;
+ *((uint32_t *) buffer) = spi_r32(SFDR);
+/* printk("%.8x ", *((uint32_t*) buffer)); */
+ buffer += 4;
+ length -= 4;
+ }
+
+ /* The rest needs to be read 1 byte a time */
+ sfcsr &= SPI_LEN_INIT|SPI_LEN1;
+ SPI_WAIT_READY;
+ spi_w32w(sfcsr, SFCSR);
+ while (length > 0) {
+ SPI_WAIT_READY;
+ *(buffer) = spi_r32(SFDR) >> 24;
+/* printk("%.2x ", *(buffer)); */
+ buffer++;
+ length--;
+ }
+ return len;
+
+}
+
+/*
+ * Do write (Page Programming) in 3 or 4 Byte addressing mode
+ */
+static ssize_t rtl838x_do_4b_write(struct rtl838x_nor *rtl838x_nor, loff_t to,
+ size_t length, const u_char *buffer,
+ uint8_t command)
+{
+ int sfcsr_addr_len = rtl838x_nor->fourByteMode ? 0x3 : 0x2;
+ int sfdr_addr_shift = rtl838x_nor->fourByteMode ? 0 : 8;
+ uint32_t sfcsr;
+ uint32_t len = length;
+
+ pr_debug("Write to %llx, len %x, shift %d\n",
+ to, sfcsr_addr_len, sfdr_addr_shift);
+ sfcsr = spi_prep(rtl838x_nor);
+
+ /* Send write command, command IO-width is 1 (bit 25/26) */
+ spi_w32w(sfcsr | SPI_LEN1 | (0 << 25), SFCSR);
+ spi_w32w(command << 24, SFDR);
+
+ /* Send address */
+ spi_w32w(sfcsr | (sfcsr_addr_len << 28) | (0 << 25), SFCSR);
+ spi_w32w(to << sfdr_addr_shift, SFDR);
+
+ /* Write Data, 1 byte at a time, if we are not 4-byte aligned */
+ if (((long)buffer) % 4) {
+ spi_w32w(sfcsr | SPI_LEN1, SFCSR);
+ while (length > 0 && (((long)buffer) % 4)) {
+ SPI_WAIT_READY;
+ spi_w32(*(buffer) << 24, SFDR);
+ buffer += 1;
+ length -= 1;
+ }
+ }
+
+ /* Now we can write 4 bytes at a time */
+ SPI_WAIT_READY;
+ spi_w32w(sfcsr | SPI_LEN4, SFCSR);
+ while (length >= 4) {
+ SPI_WAIT_READY;
+ spi_w32(*((uint32_t *)buffer), SFDR);
+ buffer += 4;
+ length -= 4;
+ }
+
+ /* Final bytes might need to be written 1 byte at a time, again */
+ SPI_WAIT_READY;
+ spi_w32w(sfcsr | SPI_LEN1, SFCSR);
+ while (length > 0) {
+ SPI_WAIT_READY;
+ spi_w32(*(buffer) << 24, SFDR);
+ buffer++;
+ length--;
+ }
+ return len;
+}
+
+static ssize_t rtl838x_nor_write(struct spi_nor *nor, loff_t to, size_t len,
+ const u_char *buffer)
+{
+ int ret = 0;
+ uint32_t offset = 0;
+ struct rtl838x_nor *rtl838x_nor = nor->priv;
+ size_t l = len;
+ uint8_t cmd = SPINOR_OP_PP;
+
+ /* Do write in 4-byte mode on large Macronix chips */
+ if (rtl838x_nor->fourByteMode) {
+ cmd = SPINOR_OP_PP_4B;
+ spi_4b_set(rtl838x_nor, true);
+ }
+
+ pr_debug("In %s %8x to: %llx\n", __func__,
+ (unsigned int) rtl838x_nor, to);
+
+ while (l >= SPI_MAX_TRANSFER_SIZE) {
+ while
+ (rtl838x_nor_get_SR(rtl838x_nor) & SPI_WIP);
+ do {
+ spi_write_enable(rtl838x_nor);
+ } while (!(rtl838x_nor_get_SR(rtl838x_nor) & SPI_WEL));
+ ret = rtl838x_do_4b_write(rtl838x_nor, to + offset,
+ SPI_MAX_TRANSFER_SIZE, buffer+offset, cmd);
+ l -= SPI_MAX_TRANSFER_SIZE;
+ offset += SPI_MAX_TRANSFER_SIZE;
+ }
+
+ if (l > 0) {
+ while
+ (rtl838x_nor_get_SR(rtl838x_nor) & SPI_WIP);
+ do {
+ spi_write_enable(rtl838x_nor);
+ } while (!(rtl838x_nor_get_SR(rtl838x_nor) & SPI_WEL));
+ ret = rtl838x_do_4b_write(rtl838x_nor, to+offset,
+ len, buffer+offset, cmd);
+ }
+
+ return len;
+}
+
+static ssize_t rtl838x_nor_read(struct spi_nor *nor, loff_t from,
+ size_t length, u_char *buffer)
+{
+ uint32_t offset = 0;
+ uint8_t cmd = SPINOR_OP_READ_FAST;
+ size_t l = length;
+ struct rtl838x_nor *rtl838x_nor = nor->priv;
+
+ /* Do fast read in 3, or 4-byte mode on large Macronix chips */
+ if (rtl838x_nor->fourByteMode) {
+ cmd = SPINOR_OP_READ_FAST_4B;
+ spi_4b_set(rtl838x_nor, true);
+ }
+
+ /* TODO: do timeout and return error */
+ pr_debug("Waiting for pending writes\n");
+ while
+ (rtl838x_nor_get_SR(rtl838x_nor) & SPI_WIP);
+ do {
+ spi_write_enable(rtl838x_nor);
+ } while (!(rtl838x_nor_get_SR(rtl838x_nor) & SPI_WEL));
+
+ pr_debug("cmd is %d\n", cmd);
+ pr_debug("%s: addr %.8llx to addr %.8x, cmd %.8x, size %d\n", __func__,
+ from, (u32)buffer, (u32)cmd, length);
+
+ while (l >= SPI_MAX_TRANSFER_SIZE) {
+ rtl838x_do_4bf_read(rtl838x_nor, from + offset,
+ SPI_MAX_TRANSFER_SIZE, buffer+offset, cmd);
+ l -= SPI_MAX_TRANSFER_SIZE;
+ offset += SPI_MAX_TRANSFER_SIZE;
+ }
+
+ if (l > 0)
+ rtl838x_do_4bf_read(rtl838x_nor, from + offset, l, buffer+offset, cmd);
+
+ return length;
+}
+
+static int rtl838x_erase(struct spi_nor *nor, loff_t offs)
+{
+ struct rtl838x_nor *rtl838x_nor = nor->priv;
+ int sfcsr_addr_len = rtl838x_nor->fourByteMode ? 0x3 : 0x2;
+ int sfdr_addr_shift = rtl838x_nor->fourByteMode ? 0 : 8;
+ uint32_t sfcsr;
+ uint8_t cmd = SPINOR_OP_SE;
+
+ pr_debug("Erasing sector at %llx\n", offs);
+
+ /* Do erase in 4-byte mode on large Macronix chips */
+ if (rtl838x_nor->fourByteMode) {
+ cmd = SPINOR_OP_SE_4B;
+ spi_4b_set(rtl838x_nor, true);
+ }
+ /* TODO: do timeout and return error */
+ while
+ (rtl838x_nor_get_SR(rtl838x_nor) & SPI_WIP);
+ do {
+ spi_write_enable(rtl838x_nor);
+ } while (!(rtl838x_nor_get_SR(rtl838x_nor) & SPI_WEL));
+
+ sfcsr = spi_prep(rtl838x_nor);
+
+ /* Send erase command, command IO-width is 1 (bit 25/26) */
+ spi_w32w(sfcsr | SPI_LEN1 | (0 << 25), SFCSR);
+ spi_w32w(cmd << 24, SFDR);
+
+ /* Send address */
+ spi_w32w(sfcsr | (sfcsr_addr_len << 28) | (0 << 25), SFCSR);
+ spi_w32w(offs << sfdr_addr_shift, SFDR);
+
+ return 0;
+}
+
+static int rtl838x_nor_read_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len)
+{
+ int length = len;
+ u8 *buffer = buf;
+ uint32_t sfcsr, sfdr;
+ struct rtl838x_nor *rtl838x_nor = nor->priv;
+
+ pr_debug("In %s: opcode %x, len %x\n", __func__, opcode, len);
+
+ sfcsr = spi_prep(rtl838x_nor);
+ sfdr = opcode << 24;
+
+ sfcsr |= SPI_LEN1;
+
+ spi_w32w(sfcsr, SFCSR);
+ spi_w32w(sfdr, SFDR);
+
+ while (length > 0) {
+ SPI_WAIT_READY;
+ *(buffer) = spi_r32(SFDR) >> 24;
+ buffer++;
+ length--;
+ }
+
+ return len;
+}
+
+static int rtl838x_nor_write_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len)
+{
+ uint32_t sfcsr, sfdr;
+ struct rtl838x_nor *rtl838x_nor = nor->priv;
+
+ pr_debug("In %s, opcode %x, len %x\n", __func__, opcode, len);
+ sfcsr = spi_prep(rtl838x_nor);
+ sfdr = opcode << 24;
+
+ if (len == 1) { /* SPINOR_OP_WRSR */
+ sfdr |= buf[0];
+ sfcsr |= SPI_LEN2;
+ }
+ spi_w32w(sfcsr, SFCSR);
+ spi_w32w(sfdr, SFDR);
+ return 0;
+}
+
+static int spi_enter_sio(struct spi_nor *nor)
+{
+ uint32_t sfcsr, sfcr2, sfdr;
+ uint32_t ret = 0, reg = 0, size_bits;
+ struct rtl838x_nor *rtl838x_nor = nor->priv;
+
+ pr_debug("In %s\n", __func__);
+ rtl838x_nor->io_status = 0;
+ sfdr = SPI_C_RSTQIO << 24;
+ sfcsr = spi_prep(rtl838x_nor);
+
+ reg = spi_r32(SFCR2);
+ pr_debug("SFCR2: %x, size %x, rdopt: %x\n", reg, SFCR2_GETSIZE(reg),
+ (reg & SFCR2_RDOPT));
+ size_bits = rtl838x_nor->fourByteMode ? SFCR2_SIZE(0x6) : SFCR2_SIZE(0x7);
+
+ sfcr2 = SFCR2_HOLD_TILL_SFDR2 | size_bits
+ | (reg & SFCR2_RDOPT) | SFCR2_CMDIO(0)
+ | SFCR2_ADDRIO(0) | SFCR2_DUMMYCYCLE(4)
+ | SFCR2_DATAIO(0) | SFCR2_SFCMD(SPINOR_OP_READ_FAST);
+ pr_debug("SFCR2: %x, size %x\n", reg, SFCR2_GETSIZE(reg));
+
+ SPI_WAIT_READY;
+ spi_w32w(sfcr2, SFCR2);
+ spi_w32w(sfcsr, SFCSR);
+ spi_w32w(sfdr, SFDR);
+
+ spi_w32_mask(SFCR2_HOLD_TILL_SFDR2, 0, SFCR2);
+ rtl838x_nor->io_status &= ~IOSTATUS_CIO_MASK;
+ rtl838x_nor->io_status |= CIO1;
+
+ spi_prep(rtl838x_nor);
+
+ return ret;
+}
+
+int rtl838x_spi_nor_scan(struct spi_nor *nor, const char *name)
+{
+ static const struct spi_nor_hwcaps hwcaps = {
+ .mask = SNOR_HWCAPS_READ | SNOR_HWCAPS_PP
+ | SNOR_HWCAPS_READ_FAST
+ };
+
+ struct rtl838x_nor *rtl838x_nor = nor->priv;
+
+ pr_debug("In %s\n", __func__);
+
+ spi_w32_mask(0, SFCR_EnableWBO, SFCR);
+ spi_w32_mask(0, SFCR_EnableRBO, SFCR);
+
+ rtl838x_nor->flags = CS0 | R_MODE;
+
+ spi_nor_scan(nor, NULL, &hwcaps);
+ pr_debug("------------- Got size: %llx\n", nor->mtd.size);
+
+ return 0;
+}
+
+int rtl838x_nor_init(struct rtl838x_nor *rtl838x_nor,
+ struct device_node *flash_node)
+{
+ int ret;
+ struct spi_nor *nor;
+
+ pr_info("%s called\n", __func__);
+ nor = &rtl838x_nor->nor;
+ nor->dev = rtl838x_nor->dev;
+ nor->priv = rtl838x_nor;
+ spi_nor_set_flash_node(nor, flash_node);
+
+ nor->read_reg = rtl838x_nor_read_reg;
+ nor->write_reg = rtl838x_nor_write_reg;
+ nor->read = rtl838x_nor_read;
+ nor->write = rtl838x_nor_write;
+ nor->erase = rtl838x_erase;
+ nor->mtd.name = "rtl838x_nor";
+ nor->erase_opcode = rtl838x_nor->fourByteMode ? SPINOR_OP_SE_4B
+ : SPINOR_OP_SE;
+ /* initialized with NULL */
+ ret = rtl838x_spi_nor_scan(nor, NULL);
+ if (ret)
+ return ret;
+
+ spi_enter_sio(nor);
+ spi_write_disable(rtl838x_nor);
+
+ ret = mtd_device_parse_register(&nor->mtd, NULL, NULL, NULL, 0);
+ return ret;
+}
+
+static int rtl838x_nor_drv_probe(struct platform_device *pdev)
+{
+ struct device_node *flash_np;
+ struct resource *res;
+ int ret;
+ struct rtl838x_nor *rtl838x_nor;
+ int addrMode;
+
+ pr_info("Initializing rtl838x_nor_driver\n");
+ if (!pdev->dev.of_node) {
+ dev_err(&pdev->dev, "No DT found\n");
+ return -EINVAL;
+ }
+
+ rtl838x_nor = devm_kzalloc(&pdev->dev, sizeof(*rtl838x_nor), GFP_KERNEL);
+ if (!rtl838x_nor)
+ return -ENOMEM;
+ platform_set_drvdata(pdev, rtl838x_nor);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ rtl838x_nor->base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR((void *)rtl838x_nor->base))
+ return PTR_ERR((void *)rtl838x_nor->base);
+
+ pr_info("SPI resource base is %08x\n", (u32)rtl838x_nor->base);
+ rtl838x_nor->dev = &pdev->dev;
+
+ /* only support one attached flash */
+ flash_np = of_get_next_available_child(pdev->dev.of_node, NULL);
+ if (!flash_np) {
+ dev_err(&pdev->dev, "no SPI flash device to configure\n");
+ ret = -ENODEV;
+ goto nor_free;
+ }
+
+ /* Get the 3/4 byte address mode as configure by bootloader */
+ if (soc_info.family == RTL8390_FAMILY_ID)
+ addrMode = rtl8390_get_addr_mode(rtl838x_nor);
+ else
+ addrMode = rtl838x_get_addr_mode(rtl838x_nor);
+ pr_info("Address mode is %d bytes\n", addrMode);
+ if (addrMode == 4)
+ rtl838x_nor->fourByteMode = true;
+
+ ret = rtl838x_nor_init(rtl838x_nor, flash_np);
+
+nor_free:
+ return ret;
+}
+
+static int rtl838x_nor_drv_remove(struct platform_device *pdev)
+{
+/* struct rtl8xx_nor *rtl838x_nor = platform_get_drvdata(pdev); */
+ return 0;
+}
+
+static const struct of_device_id rtl838x_nor_of_ids[] = {
+ { .compatible = "realtek,rtl838x-nor"},
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, rtl838x_nor_of_ids);
+
+static struct platform_driver rtl838x_nor_driver = {
+ .probe = rtl838x_nor_drv_probe,
+ .remove = rtl838x_nor_drv_remove,
+ .driver = {
+ .name = "rtl838x-nor",
+ .pm = NULL,
+ .of_match_table = rtl838x_nor_of_ids,
+ },
+};
+
+module_platform_driver(rtl838x_nor_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("RTL838x SPI NOR Flash Driver");
diff --git a/target/linux/rtl838x/files-5.4/drivers/mtd/spi-nor/rtl838x-spi.h b/target/linux/rtl838x/files-5.4/drivers/mtd/spi-nor/rtl838x-spi.h
new file mode 100644
index 0000000000..1209d47b02
--- /dev/null
+++ b/target/linux/rtl838x/files-5.4/drivers/mtd/spi-nor/rtl838x-spi.h
@@ -0,0 +1,111 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) 2009 Realtek Semiconductor Corp.
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef _RTL838X_SPI_H
+#define _RTL838X_SPI_H
+
+
+/*
+ * Register access macros
+ */
+
+#define spi_r32(reg) __raw_readl(rtl838x_nor->base + reg)
+#define spi_w32(val, reg) __raw_writel(val, rtl838x_nor->base + reg)
+#define spi_w32_mask(clear, set, reg) \
+ spi_w32((spi_r32(reg) & ~(clear)) | (set), reg)
+
+#define SPI_WAIT_READY do { \
+ } while (!(spi_r32(SFCSR) & SFCSR_SPI_RDY))
+
+#define spi_w32w(val, reg) do { \
+ __raw_writel(val, rtl838x_nor->base + reg); \
+ SPI_WAIT_READY; \
+ } while (0)
+
+#define SFCR (0x00) /*SPI Flash Configuration Register*/
+ #define SFCR_CLK_DIV(val) ((val)<<29)
+ #define SFCR_EnableRBO (1<<28)
+ #define SFCR_EnableWBO (1<<27)
+ #define SFCR_SPI_TCS(val) ((val)<<23) /*4 bit, 1111 */
+
+#define SFCR2 (0x04) /*For memory mapped I/O */
+ #define SFCR2_SFCMD(val) ((val)<<24) /*8 bit, 1111_1111 */
+ #define SFCR2_SIZE(val) ((val)<<21) /*3 bit, 111 */
+ #define SFCR2_RDOPT (1<<20)
+ #define SFCR2_CMDIO(val) ((val)<<18) /*2 bit, 11 */
+ #define SFCR2_ADDRIO(val) ((val)<<16) /*2 bit, 11 */
+ #define SFCR2_DUMMYCYCLE(val) ((val)<<13) /*3 bit, 111 */
+ #define SFCR2_DATAIO(val) ((val)<<11) /*2 bit, 11 */
+ #define SFCR2_HOLD_TILL_SFDR2 (1<<10)
+ #define SFCR2_GETSIZE(x) (((x)&0x00E00000)>>21)
+
+#define SFCSR (0x08) /*SPI Flash Control&Status Register*/
+ #define SFCSR_SPI_CSB0 (1<<31)
+ #define SFCSR_SPI_CSB1 (1<<30)
+ #define SFCSR_LEN(val) ((val)<<28) /*2 bits*/
+ #define SFCSR_SPI_RDY (1<<27)
+ #define SFCSR_IO_WIDTH(val) ((val)<<25) /*2 bits*/
+ #define SFCSR_CHIP_SEL (1<<24)
+ #define SFCSR_CMD_BYTE(val) ((val)<<16) /*8 bit, 1111_1111 */
+
+#define SFDR (0x0C) /*SPI Flash Data Register*/
+#define SFDR2 (0x10) /*SPI Flash Data Register - for post SPI bootup setting*/
+ #define SPI_CS_INIT (SFCSR_SPI_CSB0 | SFCSR_SPI_CSB1 | SPI_LEN1)
+ #define SPI_CS0 SFCSR_SPI_CSB0
+ #define SPI_CS1 SFCSR_SPI_CSB1
+ #define SPI_eCS0 ((SFCSR_SPI_CSB1)) /*and SFCSR to active CS0*/
+ #define SPI_eCS1 ((SFCSR_SPI_CSB0)) /*and SFCSR to active CS1*/
+
+ #define SPI_WIP (1) /* Write In Progress */
+ #define SPI_WEL (1<<1) /* Write Enable Latch*/
+ #define SPI_SST_QIO_WIP (1<<7) /* SST QIO Flash Write In Progress */
+ #define SPI_LEN_INIT 0xCFFFFFFF /* and SFCSR to init */
+ #define SPI_LEN4 0x30000000 /* or SFCSR to set */
+ #define SPI_LEN3 0x20000000 /* or SFCSR to set */
+ #define SPI_LEN2 0x10000000 /* or SFCSR to set */
+ #define SPI_LEN1 0x00000000 /* or SFCSR to set */
+ #define SPI_SETLEN(val) do { \
+ SPI_REG(SFCSR) &= 0xCFFFFFFF; \
+ SPI_REG(SFCSR) |= (val-1)<<28; \
+ } while (0)
+/*
+ * SPI interface control
+ */
+#define RTL8390_SOC_SPI_MMIO_CONF (0x04)
+
+#define IOSTATUS_CIO_MASK (0x00000038)
+
+/* Chip select: bits 4-7*/
+#define CS0 (1<<4)
+#define R_MODE 0x04
+
+/* io_status */
+#define IO1 (1<<0)
+#define IO2 (1<<1)
+#define CIO1 (1<<3)
+#define CIO2 (1<<4)
+#define CMD_IO1 (1<<6)
+#define W_ADDR_IO1 ((1)<<12)
+#define R_ADDR_IO2 ((2)<<9)
+#define R_DATA_IO2 ((2)<<15)
+#define W_DATA_IO1 ((1)<<18)
+
+/* Commands */
+#define SPI_C_RSTQIO 0xFF
+
+#define SPI_MAX_TRANSFER_SIZE 256
+
+#endif /* _RTL838X_SPI_H */
diff --git a/target/linux/rtl838x/files-5.4/drivers/net/dsa/rtl838x.h b/target/linux/rtl838x/files-5.4/drivers/net/dsa/rtl838x.h
new file mode 100644
index 0000000000..127a31dca1
--- /dev/null
+++ b/target/linux/rtl838x/files-5.4/drivers/net/dsa/rtl838x.h
@@ -0,0 +1,188 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#ifndef _RTL838X_H
+#define _RTL838X_H
+
+#include <net/dsa.h>
+
+/*
+ * Register definition
+ */
+#define RTL838X_CPU_PORT 28
+#define RTL839X_CPU_PORT 52
+
+#define RTL838X_MAC_PORT_CTRL(port) (0xd560 + (((port) << 7)))
+#define RTL839X_MAC_PORT_CTRL(port) (0x8004 + (((port) << 7)))
+#define RTL838X_RST_GLB_CTRL_0 (0x003c)
+#define RTL838X_MAC_FORCE_MODE_CTRL (0xa104)
+#define RTL839X_MAC_FORCE_MODE_CTRL (0x02bc)
+
+#define RTL838X_DMY_REG31 (0x3b28)
+#define RTL838X_SDS_MODE_SEL (0x0028)
+#define RTL838X_SDS_CFG_REG (0x0034)
+#define RTL838X_INT_MODE_CTRL (0x005c)
+#define RTL838X_CHIP_INFO (0x00d8)
+#define RTL839X_CHIP_INFO (0x0ff4)
+#define RTL838X_SDS4_REG28 (0xef80)
+#define RTL838X_SDS4_DUMMY0 (0xef8c)
+#define RTL838X_SDS5_EXT_REG6 (0xf18c)
+#define RTL838X_PORT_ISO_CTRL(port) (0x4100 + ((port) << 2))
+#define RTL839X_PORT_ISO_CTRL(port) (0x1400 + ((port) << 3))
+#define RTL8380_SDS4_FIB_REG0 (0xF800)
+#define RTL838X_STAT_PORT_STD_MIB (0x1200)
+#define RTL839X_STAT_PORT_STD_MIB (0xC000)
+#define RTL838X_STAT_RST (0x3100)
+#define RTL839X_STAT_RST (0xF504)
+#define RTL838X_STAT_PORT_RST (0x3104)
+#define RTL839X_STAT_PORT_RST (0xF508)
+#define RTL838X_STAT_CTRL (0x3108)
+#define RTL839X_STAT_CTRL (0x04cc)
+
+/* Registers of the internal Serdes of the 8380 */
+#define MAPLE_SDS4_REG0r RTL838X_SDS4_REG28
+#define MAPLE_SDS5_REG0r (RTL838X_SDS4_REG28 + 0x100)
+#define MAPLE_SDS4_REG3r RTL838X_SDS4_DUMMY0
+#define MAPLE_SDS5_REG3r (RTL838X_SDS4_REG28 + 0x100)
+#define MAPLE_SDS4_FIB_REG0r (RTL838X_SDS4_REG28 + 0x880)
+#define MAPLE_SDS5_FIB_REG0r (RTL838X_SDS4_REG28 + 0x980)
+
+/* VLAN registers */
+#define RTL838X_VLAN_PROFILE(idx) (0x3A88 + ((idx) << 2))
+#define RTL838X_VLAN_PORT_EGR_FLTR (0x3A84)
+#define RTL838X_VLAN_PORT_PB_VLAN(port) (0x3C00 + ((port) << 2))
+#define RTL838X_VLAN_PORT_IGR_FLTR_0 (0x3A7C)
+#define RTL838X_VLAN_PORT_IGR_FLTR_1 (0x3A7C + 4)
+
+/* Table 0/1 access registers */
+#define RTL838X_TBL_ACCESS_CTRL_0 (0x6914)
+#define RTL838X_TBL_ACCESS_DATA_0(idx) (0x6918 + ((idx) << 2))
+#define RTL838X_TBL_ACCESS_CTRL_1 (0xA4C8)
+#define RTL838X_TBL_ACCESS_DATA_1(idx) (0xA4CC + ((idx) << 2))
+#define RTL839X_TBL_ACCESS_CTRL_0 (0x1190)
+#define RTL839X_TBL_ACCESS_DATA_0(idx) (0x1194 + ((idx) << 2))
+#define RTL839X_TBL_ACCESS_CTRL_1 (0x6b80)
+#define RTL839X_TBL_ACCESS_DATA_1(idx) (0x6b84 + ((idx) << 2))
+
+/* MAC handling */
+#define RTL838X_MAC_LINK_STS (0xa188)
+#define RTL839X_MAC_LINK_STS (0x0390)
+#define RTL838X_MAC_LINK_SPD_STS(port) (0xa190 + (((port >> 4) << 2)))
+#define RTL838X_MAC_LINK_DUP_STS (0xa19c)
+#define RTL838X_MAC_TX_PAUSE_STS (0xa1a0)
+#define RTL838X_MAC_RX_PAUSE_STS (0xa1a4)
+#define RTL838X_EEE_TX_TIMER_GIGA_CTRL (0xaa04)
+#define RTL838X_EEE_TX_TIMER_GELITE_CTRL (0xaa08)
+
+/* MAC link state bits */
+#define FORCE_EN (1 << 0)
+#define FORCE_LINK_EN (1 << 1)
+#define NWAY_EN (1 << 2)
+#define DUPLX_MODE (1 << 3)
+#define TX_PAUSE_EN (1 << 6)
+#define RX_PAUSE_EN (1 << 7)
+
+/* EEE */
+#define RTL838X_MAC_EEE_ABLTY (0xa1a8)
+#define RTL838X_EEE_PORT_TX_EN (0x014c)
+#define RTL838X_EEE_PORT_RX_EN (0x0150)
+#define RTL838X_EEE_CLK_STOP_CTRL (0x0148)
+
+/* L2 functionality */
+#define RTL838X_L2_CTRL_0 (0x3200)
+#define RTL839X_L2_CTRL_0 (0x3800)
+#define RTL838X_L2_CTRL_1 (0x3204)
+#define RTL839X_L2_CTRL_1 (0x3804)
+#define RTL838X_L2_PORT_AGING_OUT (0x3358)
+#define RTL839X_L2_PORT_AGING_OUT (0x3b74)
+#define RTL838X_TBL_ACCESS_L2_CTRL (0x6900)
+#define RTL839X_TBL_ACCESS_L2_CTRL (0x1180)
+#define RTL838X_TBL_ACCESS_L2_DATA(idx) (0x6908 + ((idx) << 2))
+#define RTL838X_TBL_ACCESS_L2_DATA(idx) (0x6908 + ((idx) << 2))
+#define RTL838X_L2_TBL_FLUSH_CTRL (0x3370)
+#define RTL839X_L2_TBL_FLUSH_CTRL (0x3ba0)
+
+/* Port Mirroring */
+#define RTL838X_MIR_CTRL(grp) (0x5D00 + (((grp) << 2)))
+#define RTL838X_MIR_DPM_CTRL(grp) (0x5D20 + (((grp) << 2)))
+#define RTL838X_MIR_SPM_CTRL(grp) (0x5D10 + (((grp) << 2)))
+
+enum phy_type {
+ PHY_NONE = 0,
+ PHY_RTL838X_SDS = 1,
+ PHY_RTL8218B_INT = 2,
+ PHY_RTL8218B_EXT = 3,
+ PHY_RTL8214FC = 4
+};
+
+struct rtl838x_port {
+ bool enable;
+ u64 pm;
+ u16 pvid;
+ bool eee_enabled;
+ enum phy_type phy;
+};
+
+struct rtl838x_vlan_info {
+ u64 untagged_ports;
+ u64 tagged_ports;
+ u32 vlan_conf;
+};
+
+struct rtl838x_switch_priv;
+
+struct rtl838x_reg {
+ void (*mask_port_reg)(u64 clear, u64 set, int reg);
+ void (*set_port_reg)(u64 set, int reg);
+ u64 (*get_port_reg)(int reg);
+ int stat_port_rst;
+ int stat_rst;
+ int (*stat_port_std_mib)(int p);
+ void (*mask_port_iso_ctrl)(u64 clear, u64 set, int port);
+ void (*set_port_iso_ctrl)(u64 set, int port);
+ int l2_ctrl_0;
+ int l2_ctrl_1;
+ int l2_port_aging_out;
+ int smi_poll_ctrl;
+ int l2_tbl_flush_ctrl;
+ void (*exec_tbl0_cmd)(u32 cmd);
+ void (*exec_tbl1_cmd)(u32 cmd);
+ int (*tbl_access_data_0)(int i);
+ int isr_glb_src;
+ int isr_port_link_sts_chg;
+ int imr_port_link_sts_chg;
+ int imr_glb;
+ void (*vlan_tables_read)(u32 vlan, struct rtl838x_vlan_info *info);
+ void (*vlan_set_tagged)(u32 vlan, u64 portmask, u32 conf);
+ void (*vlan_set_untagged)(u32 vlan, u64 portmask);
+ int (*mac_force_mode_ctrl)(int port);
+ int rst_glb_ctrl;
+};
+
+struct rtl838x_switch_priv {
+ /* Switch operation */
+ struct dsa_switch *ds;
+ struct device *dev;
+ u16 id;
+ u16 family_id;
+ char version;
+ struct rtl838x_port ports[54]; /* TODO: correct size! */
+ struct mutex reg_mutex;
+ int link_state_irq;
+ int mirror_group_ports[4];
+ struct mii_bus *mii_bus;
+ const struct rtl838x_reg *r;
+ u8 cpu_port;
+ u8 port_mask;
+};
+
+extern struct rtl838x_soc_info soc_info;
+extern void rtl8380_sds_rst(int mac);
+
+extern int rtl838x_write_phy(u32 port, u32 page, u32 reg, u32 val);
+extern int rtl839x_write_phy(u32 port, u32 page, u32 reg, u32 val);
+extern int rtl838x_read_phy(u32 port, u32 page, u32 reg, u32 *val);
+extern int rtl839x_read_phy(u32 port, u32 page, u32 reg, u32 *val);
+extern int rtl838x_write_mmd_phy(u32 port, u32 addr, u32 reg, u32 val);
+extern int rtl838x_read_mmd_phy(u32 port, u32 addr, u32 reg, u32 *val);
+
+#endif /* _RTL838X_H */
diff --git a/target/linux/rtl838x/files-5.4/drivers/net/dsa/rtl838x_phy.c b/target/linux/rtl838x/files-5.4/drivers/net/dsa/rtl838x_phy.c
new file mode 100644
index 0000000000..4440dc99cd
--- /dev/null
+++ b/target/linux/rtl838x/files-5.4/drivers/net/dsa/rtl838x_phy.c
@@ -0,0 +1,1286 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Realtek RTL838X Ethernet MDIO interface driver
+ *
+ * Copyright (C) 2020 B. Koblitz
+ */
+
+#include <linux/delay.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/of_mdio.h>
+#include <linux/phy.h>
+#include <linux/platform_device.h>
+#include <linux/firmware.h>
+#include <linux/crc32.h>
+
+#include <asm/mach-rtl838x/mach-rtl838x.h>
+#include "rtl838x.h"
+
+/* External RTL8218B and RTL8214FC IDs are identical */
+#define PHY_ID_RTL8214C 0x001cc942
+#define PHY_ID_RTL8214FC 0x001cc981
+#define PHY_ID_RTL8218B_E 0x001cc981
+#define PHY_ID_RTL8218B_I 0x001cca40
+#define PHY_ID_RTL8390_GENERIC 0x001ccab0
+
+struct __attribute__ ((__packed__)) part {
+ uint16_t start;
+ uint8_t wordsize;
+ uint8_t words;
+};
+
+struct __attribute__ ((__packed__)) fw_header {
+ uint32_t magic;
+ uint32_t phy;
+ uint32_t checksum;
+ uint32_t version;
+ struct part parts[10];
+};
+
+#define FIRMWARE_838X_8380_1 "rtl838x_phy/rtl838x_8380.fw"
+#define FIRMWARE_838X_8214FC_1 "rtl838x_phy/rtl838x_8214fc.fw"
+#define FIRMWARE_838X_8218b_1 "rtl838x_phy/rtl838x_8218b.fw"
+
+static const struct firmware rtl838x_8380_fw;
+static const struct firmware rtl838x_8214fc_fw;
+static const struct firmware rtl838x_8218b_fw;
+
+struct rtl838x_phy_priv {
+ char *name;
+};
+
+static int read_phy(u32 port, u32 page, u32 reg, u32 *val)
+{
+ if (soc_info.family == RTL8390_FAMILY_ID)
+ return rtl839x_read_phy(port, page, reg, val);
+ else
+ return rtl838x_read_phy(port, page, reg, val);
+}
+
+static int write_phy(u32 port, u32 page, u32 reg, u32 val)
+{
+ if (soc_info.family == RTL8390_FAMILY_ID)
+ return rtl839x_write_phy(port, page, reg, val);
+ else
+ return rtl838x_write_phy(port, page, reg, val);
+}
+
+static void rtl8380_int_phy_on_off(int mac, bool on)
+{
+ u32 val;
+
+ read_phy(mac, 0, 0, &val);
+ if (on)
+ write_phy(mac, 0, 0, val & ~(1 << 11));
+ else
+ write_phy(mac, 0, 0, val | (1 << 11));
+}
+
+static void rtl8380_rtl8214fc_on_off(int mac, bool on)
+{
+ u32 val;
+
+ /* fiber ports */
+ write_phy(mac, 4095, 30, 3);
+ read_phy(mac, 0, 16, &val);
+ if (on)
+ write_phy(mac, 0, 16, val & ~(1 << 11));
+ else
+ write_phy(mac, 0, 16, val | (1 << 11));
+
+ /* copper ports */
+ write_phy(mac, 4095, 30, 1);
+ read_phy(mac, 0, 16, &val);
+ if (on)
+ write_phy(mac, 0xa40, 16, val & ~(1 << 11));
+ else
+ write_phy(mac, 0xa40, 16, val | (1 << 11));
+}
+
+static void rtl8380_phy_reset(int mac)
+{
+ u32 val;
+
+ read_phy(mac, 0, 0, &val);
+ write_phy(mac, 0, 0, val | (0x1 << 15));
+}
+
+void rtl8380_sds_rst(int mac)
+{
+ u32 offset = (mac == 24) ? 0 : 0x100;
+
+ sw_w32_mask(1 << 11, 0, RTL8380_SDS4_FIB_REG0 + offset);
+ sw_w32_mask(0x3, 0, RTL838X_SDS4_REG28 + offset);
+ sw_w32_mask(0x3, 0x3, RTL838X_SDS4_REG28 + offset);
+ sw_w32_mask(0, 0x1 << 6, RTL838X_SDS4_DUMMY0 + offset);
+ sw_w32_mask(0x1 << 6, 0, RTL838X_SDS4_DUMMY0 + offset);
+ pr_info("SERDES reset: %d\n", mac);
+}
+
+static struct fw_header *
+rtl838x_request_fw(struct phy_device *phydev, const struct firmware *fw,
+ const char *name)
+{
+ struct device *dev = &phydev->mdio.dev;
+ int err;
+ struct fw_header *h;
+ uint32_t checksum, my_checksum;
+
+ err = request_firmware(&fw, name, dev);
+ if (err < 0)
+ goto out;
+
+ if (fw->size < sizeof(struct fw_header)) {
+ pr_err("Firmware size too small.\n");
+ err = -EINVAL;
+ goto out;
+ }
+
+ h = (struct fw_header *) fw->data;
+ pr_info("Firmware loaded. Size %d, magic: %08x\n", fw->size, h->magic);
+
+ if (h->phy != 0x83800000) {
+ pr_err("Wrong firmware file: PHY mismatch.\n");
+ goto out;
+ }
+
+ checksum = h->checksum;
+ h->checksum = 0;
+ my_checksum = ~crc32(0xFFFFFFFFU, fw->data, fw->size);
+ if (checksum != my_checksum) {
+ pr_err("Firmware checksum mismatch.\n");
+ err = -EINVAL;
+ goto out;
+ }
+ h->checksum = checksum;
+
+ return h;
+out:
+ dev_err(dev, "Unable to load firmware %s (%d)\n", name, err);
+ return NULL;
+}
+
+static int rtl8390_configure_generic(struct phy_device *phydev)
+{
+ u32 val, phy_id;
+ int mac = phydev->mdio.addr;
+
+ read_phy(mac, 0, 2, &val);
+ phy_id = val << 16;
+ read_phy(mac, 0, 3, &val);
+ phy_id |= val;
+ pr_debug("Phy on MAC %d: %x\n", mac, phy_id);
+
+ /* Read internal PHY ID */
+ write_phy(mac, 31, 27, 0x0002);
+ read_phy(mac, 31, 28, &val);
+
+ /* Internal RTL8218B, version 2 */
+ phydev_info(phydev, "Detected unknown %x\n", val);
+ return 0;
+}
+
+static int rtl8380_configure_int_rtl8218b(struct phy_device *phydev)
+{
+ u32 val, phy_id;
+ int i, p, ipd_flag;
+ int mac = phydev->mdio.addr;
+ struct fw_header *h;
+ u32 *rtl838x_6275B_intPhy_perport;
+ u32 *rtl8218b_6276B_hwEsd_perport;
+
+
+ read_phy(mac, 0, 2, &val);
+ phy_id = val << 16;
+ read_phy(mac, 0, 3, &val);
+ phy_id |= val;
+ pr_debug("Phy on MAC %d: %x\n", mac, phy_id);
+
+ /* Read internal PHY ID */
+ write_phy(mac, 31, 27, 0x0002);
+ read_phy(mac, 31, 28, &val);
+ if (val != 0x6275) {
+ phydev_err(phydev, "Expected internal RTL8218B, found PHY-ID %x\n", val);
+ return -1;
+ }
+
+ /* Internal RTL8218B, version 2 */
+ phydev_info(phydev, "Detected internal RTL8218B\n");
+
+ h = rtl838x_request_fw(phydev, &rtl838x_8380_fw, FIRMWARE_838X_8380_1);
+ if (!h)
+ return -1;
+
+ if (h->phy != 0x83800000) {
+ phydev_err(phydev, "Wrong firmware file: PHY mismatch.\n");
+ return -1;
+ }
+
+ rtl838x_6275B_intPhy_perport = (void *)h + sizeof(struct fw_header)
+ + h->parts[8].start;
+
+ rtl8218b_6276B_hwEsd_perport = (void *)h + sizeof(struct fw_header)
+ + h->parts[9].start;
+
+ if (sw_r32(RTL838X_DMY_REG31) == 0x1)
+ ipd_flag = 1;
+
+ read_phy(mac, 0, 0, &val);
+ if (val & (1 << 11))
+ rtl8380_int_phy_on_off(mac, true);
+ else
+ rtl8380_phy_reset(mac);
+ msleep(100);
+
+ /* Ready PHY for patch */
+ for (p = 0; p < 8; p++) {
+ write_phy(mac + p, 0xfff, 0x1f, 0x0b82);
+ write_phy(mac + p, 0xfff, 0x10, 0x0010);
+ }
+ msleep(500);
+ for (p = 0; p < 8; p++) {
+ for (i = 0; i < 100 ; i++) {
+ read_phy(mac + p, 0x0b80, 0x10, &val);
+ if (val & 0x40)
+ break;
+ }
+ if (i >= 100) {
+ phydev_err(phydev,
+ "ERROR: Port %d not ready for patch.\n",
+ mac + p);
+ return -1;
+ }
+ }
+ for (p = 0; p < 8; p++) {
+ i = 0;
+ while (rtl838x_6275B_intPhy_perport[i * 2]) {
+ write_phy(mac + p, 0xfff,
+ rtl838x_6275B_intPhy_perport[i * 2],
+ rtl838x_6275B_intPhy_perport[i * 2 + 1]);
+ i++;
+ }
+ i = 0;
+ while (rtl8218b_6276B_hwEsd_perport[i * 2]) {
+ write_phy(mac + p, 0xfff,
+ rtl8218b_6276B_hwEsd_perport[i * 2],
+ rtl8218b_6276B_hwEsd_perport[i * 2 + 1]);
+ i++;
+ }
+ }
+ return 0;
+}
+
+static int rtl8380_configure_ext_rtl8218b(struct phy_device *phydev)
+{
+ u32 val, ipd, phy_id;
+ int i, l;
+ int mac = phydev->mdio.addr;
+ struct fw_header *h;
+ u32 *rtl8380_rtl8218b_perchip;
+ u32 *rtl8218B_6276B_rtl8380_perport;
+ u32 *rtl8380_rtl8218b_perport;
+
+ if (soc_info.family == RTL8380_FAMILY_ID && mac != 0 && mac != 16) {
+ phydev_err(phydev, "External RTL8218B must have PHY-IDs 0 or 16!\n");
+ return -1;
+ }
+ read_phy(mac, 0, 2, &val);
+ phy_id = val << 16;
+ read_phy(mac, 0, 3, &val);
+ phy_id |= val;
+ pr_info("Phy on MAC %d: %x\n", mac, phy_id);
+
+ /* Read internal PHY ID */
+ write_phy(mac, 31, 27, 0x0002);
+ read_phy(mac, 31, 28, &val);
+ if (val != 0x6276) {
+ phydev_err(phydev, "Expected external RTL8218B, found PHY-ID %x\n", val);
+ return -1;
+ }
+ phydev_info(phydev, "Detected external RTL8218B\n");
+
+ h = rtl838x_request_fw(phydev, &rtl838x_8218b_fw, FIRMWARE_838X_8218b_1);
+ if (!h)
+ return -1;
+
+ if (h->phy != 0x8218b00) {
+ phydev_err(phydev, "Wrong firmware file: PHY mismatch.\n");
+ return -1;
+ }
+
+ rtl8380_rtl8218b_perchip = (void *)h + sizeof(struct fw_header)
+ + h->parts[0].start;
+
+ rtl8218B_6276B_rtl8380_perport = (void *)h + sizeof(struct fw_header)
+ + h->parts[1].start;
+
+ rtl8380_rtl8218b_perport = (void *)h + sizeof(struct fw_header)
+ + h->parts[2].start;
+
+ read_phy(mac, 0, 0, &val);
+ if (val & (1 << 11))
+ rtl8380_int_phy_on_off(mac, true);
+ else
+ rtl8380_phy_reset(mac);
+ msleep(100);
+
+ /* Get Chip revision */
+ write_phy(mac, 0xfff, 0x1f, 0x0);
+ write_phy(mac, 0xfff, 0x1b, 0x4);
+ read_phy(mac, 0xfff, 0x1c, &val);
+
+ i = 0;
+ while (rtl8380_rtl8218b_perchip[i * 3]
+ && rtl8380_rtl8218b_perchip[i * 3 + 1]) {
+ write_phy(mac + rtl8380_rtl8218b_perchip[i * 3],
+ 0xfff, rtl8380_rtl8218b_perchip[i * 3 + 1],
+ rtl8380_rtl8218b_perchip[i * 3 + 2]);
+ i++;
+ }
+
+ /* Enable PHY */
+ for (i = 0; i < 8; i++) {
+ write_phy(mac + i, 0xfff, 0x1f, 0x0000);
+ write_phy(mac + i, 0xfff, 0x00, 0x1140);
+ }
+ mdelay(100);
+
+ /* Request patch */
+ for (i = 0; i < 8; i++) {
+ write_phy(mac + i, 0xfff, 0x1f, 0x0b82);
+ write_phy(mac + i, 0xfff, 0x10, 0x0010);
+ }
+ mdelay(300);
+
+ /* Verify patch readiness */
+ for (i = 0; i < 8; i++) {
+ for (l = 0; l < 100; l++) {
+ read_phy(mac + i, 0xb80, 0x10, &val);
+ if (val & 0x40)
+ break;
+ }
+ if (l >= 100) {
+ phydev_err(phydev, "Could not patch PHY\n");
+ return -1;
+ }
+ }
+
+ /* Use Broadcast ID method for patching */
+ write_phy(mac, 0xfff, 0x1f, 0x0000);
+ write_phy(mac, 0xfff, 0x1d, 0x0008);
+ write_phy(mac, 0xfff, 0x1f, 0x0266);
+ write_phy(mac, 0xfff, 0x16, 0xff00 + mac);
+ write_phy(mac, 0xfff, 0x1f, 0x0000);
+ write_phy(mac, 0xfff, 0x1d, 0x0000);
+ mdelay(1);
+
+ write_phy(mac, 0xfff, 30, 8);
+ write_phy(mac, 0x26e, 17, 0xb);
+ write_phy(mac, 0x26e, 16, 0x2);
+ mdelay(1);
+ read_phy(mac, 0x26e, 19, &ipd);
+ write_phy(mac, 0, 30, 0);
+ ipd = (ipd >> 4) & 0xf;
+
+ i = 0;
+ while (rtl8218B_6276B_rtl8380_perport[i * 2]) {
+ write_phy(mac, 0xfff, rtl8218B_6276B_rtl8380_perport[i * 2],
+ rtl8218B_6276B_rtl8380_perport[i * 2 + 1]);
+ i++;
+ }
+
+ /*Disable broadcast ID*/
+ write_phy(mac, 0xfff, 0x1f, 0x0000);
+ write_phy(mac, 0xfff, 0x1d, 0x0008);
+ write_phy(mac, 0xfff, 0x1f, 0x0266);
+ write_phy(mac, 0xfff, 0x16, 0x00 + mac);
+ write_phy(mac, 0xfff, 0x1f, 0x0000);
+ write_phy(mac, 0xfff, 0x1d, 0x0000);
+ mdelay(1);
+
+ return 0;
+}
+
+static int rtl8218b_ext_match_phy_device(struct phy_device *phydev)
+{
+ int addr = phydev->mdio.addr;
+
+ return phydev->phy_id == PHY_ID_RTL8218B_E && addr < 8;
+}
+
+
+static int rtl8380_rtl8218b_write_mmd(struct phy_device *phydev,
+ int devnum, u16 regnum, u16 val)
+{
+ int addr = phydev->mdio.addr;
+
+ return rtl838x_write_mmd_phy(addr, devnum, regnum, val);
+}
+
+static int rtl8380_rtl8218b_read_mmd(struct phy_device *phydev,
+ int devnum, u16 regnum)
+{
+ int ret;
+ u32 val;
+ int addr = phydev->mdio.addr;
+
+ ret = rtl838x_read_mmd_phy(addr, devnum, regnum, &val);
+ if (ret)
+ return ret;
+ return val;
+}
+
+static void rtl8380_rtl8214fc_media_set(int mac, bool set_fibre)
+{
+ int base = mac - (mac % 4);
+ static int reg[] = {16, 19, 20, 21};
+ int val, media, power;
+
+ pr_info("%s: port %d, set_fibre: %d\n", __func__, mac, set_fibre);
+ write_phy(base, 0xfff, 29, 8);
+ read_phy(base, 0x266, reg[mac % 4], &val);
+
+ media = (val >> 10) & 0x3;
+ pr_info("Current media %x\n", media);
+ if (media & 0x2) {
+ pr_info("Powering off COPPER\n");
+ write_phy(base, 0xfff, 29, 1);
+ /* Ensure power is off */
+ read_phy(base, 0xa40, 16, &power);
+ if (!(power & (1 << 11)))
+ write_phy(base, 0xa40, 16, power | (1 << 11));
+ } else {
+ pr_info("Powering off FIBRE");
+ write_phy(base, 0xfff, 29, 3);
+ /* Ensure power is off */
+ read_phy(base, 0xa40, 16, &power);
+ if (!(power & (1 << 11)))
+ write_phy(base, 0xa40, 16, power | (1 << 11));
+ }
+
+ if (set_fibre) {
+ val |= 1 << 10;
+ val &= ~(1 << 11);
+ } else {
+ val |= 1 << 10;
+ val |= 1 << 11;
+ }
+ write_phy(base, 0xfff, 29, 8);
+ write_phy(base, 0x266, reg[mac % 4], val);
+ write_phy(base, 0xfff, 29, 0);
+
+ if (set_fibre) {
+ pr_info("Powering on FIBRE");
+ write_phy(base, 0xfff, 29, 3);
+ /* Ensure power is off */
+ read_phy(base, 0xa40, 16, &power);
+ if (power & (1 << 11))
+ write_phy(base, 0xa40, 16, power & ~(1 << 11));
+ } else {
+ pr_info("Powering on COPPER\n");
+ write_phy(base, 0xfff, 29, 1);
+ /* Ensure power is off */
+ read_phy(base, 0xa40, 16, &power);
+ if (power & (1 << 11))
+ write_phy(base, 0xa40, 16, power & ~(1 << 11));
+ }
+
+ write_phy(base, 0xfff, 29, 0);
+}
+
+static bool rtl8380_rtl8214fc_media_is_fibre(int mac)
+{
+ int base = mac - (mac % 4);
+ static int reg[] = {16, 19, 20, 21};
+ u32 val;
+
+ write_phy(base, 0xfff, 29, 8);
+ read_phy(base, 0x266, reg[mac % 4], &val);
+ write_phy(base, 0xfff, 29, 0);
+ if (val & (1 << 11))
+ return false;
+ return true;
+}
+
+static int rtl8380_rtl8214fc_set_port(struct phy_device *phydev, int port)
+{
+ bool is_fibre = (port == PORT_FIBRE ? true : false);
+ int addr = phydev->mdio.addr;
+
+ pr_debug("%s port %d to %d\n", __func__, addr, port);
+
+ rtl8380_rtl8214fc_media_set(addr, is_fibre);
+ return 0;
+}
+
+static int rtl8380_rtl8214fc_get_port(struct phy_device *phydev)
+{
+ int addr = phydev->mdio.addr;
+
+ pr_debug("%s: port %d\n", __func__, addr);
+ if (rtl8380_rtl8214fc_media_is_fibre(addr))
+ return PORT_FIBRE;
+ return PORT_MII;
+}
+
+void rtl8380_rtl8214fc_ldps_set(int mac, struct ethtool_eee *e)
+{
+
+}
+
+static void rtl8380_rtl8218b_eee_set_u_boot(int port, bool enable)
+{
+ u32 val;
+ bool an_enabled;
+
+ /* Set GPHY page to copper */
+ write_phy(port, 0, 30, 0x0001);
+ read_phy(port, 0, 0, &val);
+ an_enabled = val & (1 << 12);
+
+ if (enable) {
+ /* 100/1000M EEE Capability */
+ write_phy(port, 0, 13, 0x0007);
+ write_phy(port, 0, 14, 0x003C);
+ write_phy(port, 0, 13, 0x4007);
+ write_phy(port, 0, 14, 0x0006);
+
+ read_phy(port, 0x0A43, 25, &val);
+ val |= 1 << 4;
+ write_phy(port, 0x0A43, 25, val);
+ } else {
+ /* 100/1000M EEE Capability */
+ write_phy(port, 0, 13, 0x0007);
+ write_phy(port, 0, 14, 0x003C);
+ write_phy(port, 0, 13, 0x0007);
+ write_phy(port, 0, 14, 0x0000);
+
+ read_phy(port, 0x0A43, 25, &val);
+ val &= ~(1 << 4);
+ write_phy(port, 0x0A43, 25, val);
+ }
+
+ /* Restart AN if enabled */
+ if (an_enabled) {
+ read_phy(port, 0, 0, &val);
+ val |= (1 << 12) | (1 << 9);
+ write_phy(port, 0, 0, val);
+ }
+
+ /* GPHY page back to auto*/
+ write_phy(port, 0xa42, 29, 0);
+}
+
+static int rtl8380_rtl8218b_get_eee_u_boot(struct phy_device *phydev, struct ethtool_eee *e)
+{
+ u32 val;
+ int addr = phydev->mdio.addr;
+
+ pr_debug("In %s %d\n", __func__, addr);
+
+ /* Set GPHY page to copper */
+ write_phy(addr, 0xa42, 29, 0x0001);
+
+ read_phy(addr, 0xa43, 25, &val);
+ if (e->eee_enabled && (!!(val & (1 << 4))))
+ e->eee_enabled = !!(val & (1 << 4));
+ else
+ e->eee_enabled = 0;
+
+ /* GPHY page to auto */
+ write_phy(addr, 0xa42, 29, 0x0000);
+
+ return 0;
+}
+
+void rtl8380_rtl8218b_eee_set(int port, bool enable)
+{
+ u32 val;
+ bool an_enabled;
+
+ pr_debug("In %s %d, enable %d\n", __func__, port, enable);
+ /* Set GPHY page to copper */
+ write_phy(port, 0xa42, 29, 0x0001);
+
+ read_phy(port, 0, 0, &val);
+ an_enabled = val & (1 << 12);
+
+ /* MAC based EEE */
+ read_phy(port, 0xa43, 25, &val);
+ val &= ~(1 << 5);
+ write_phy(port, 0xa43, 25, val);
+
+ /* 100M / 1000M EEE */
+ if (enable)
+ rtl838x_write_mmd_phy(port, 7, 60, 0x6);
+ else
+ rtl838x_write_mmd_phy(port, 7, 60, 0);
+
+ /* 500M EEE ability */
+ read_phy(port, 0xa42, 20, &val);
+ if (enable)
+ val |= 1 << 7;
+ else
+ val &= ~(1 << 7);
+ write_phy(port, 0xa42, 20, val);
+
+ /* Restart AN if enabled */
+ if (an_enabled) {
+ read_phy(port, 0, 0, &val);
+ val |= (1 << 12) | (1 << 9);
+ write_phy(port, 0, 0, val);
+ }
+
+ /* GPHY page back to auto*/
+ write_phy(port, 0xa42, 29, 0);
+}
+
+int rtl8380_rtl8218b_get_eee(struct phy_device *phydev,
+ struct ethtool_eee *e)
+{
+ u32 val;
+ int addr = phydev->mdio.addr;
+
+ pr_debug("In %s, port %d\n", __func__, addr);
+
+ /* Set GPHY page to copper */
+ write_phy(addr, 0xa42, 29, 0x0001);
+
+ rtl838x_read_mmd_phy(addr, 7, 60, &val);
+ if (e->eee_enabled && (!!(val & (1 << 7))))
+ e->eee_enabled = !!(val & (1 << 7));
+ else
+ e->eee_enabled = 0;
+
+ /* GPHY page to auto */
+ write_phy(addr, 0xa42, 29, 0x0000);
+
+ return 0;
+}
+
+void rtl8380_rtl8218b_green_set(int mac, bool enable)
+{
+ u32 val;
+
+ /* Set GPHY page to copper */
+ write_phy(mac, 0xa42, 29, 0x0001);
+
+ write_phy(mac, 0, 27, 0x8011);
+ read_phy(mac, 0, 28, &val);
+ if (enable) {
+ val |= 1 << 9;
+ write_phy(mac, 0, 27, 0x8011);
+ write_phy(mac, 0, 28, val);
+ } else {
+ val &= ~(1 << 9);
+ write_phy(mac, 0, 27, 0x8011);
+ write_phy(mac, 0, 28, val);
+ }
+
+ /* GPHY page to auto */
+ write_phy(mac, 0xa42, 29, 0x0000);
+}
+
+int rtl8380_rtl8214fc_get_green(struct phy_device *phydev, struct ethtool_eee *e)
+{
+ u32 val;
+ int addr = phydev->mdio.addr;
+
+ pr_debug("In %s %d\n", __func__, addr);
+ /* Set GPHY page to copper */
+ write_phy(addr, 0xa42, 29, 0x0001);
+
+ write_phy(addr, 0, 27, 0x8011);
+ read_phy(addr, 0, 28, &val);
+ if (e->eee_enabled && (!!(val & (1 << 9))))
+ e->eee_enabled = !!(val & (1 << 9));
+ else
+ e->eee_enabled = 0;
+
+ /* GPHY page to auto */
+ write_phy(addr, 0xa42, 29, 0x0000);
+
+ return 0;
+}
+
+static int rtl8380_rtl8214fc_set_eee(struct phy_device *phydev,
+ struct ethtool_eee *e)
+{
+ u32 pollMask;
+ int addr = phydev->mdio.addr;
+
+ pr_debug("In %s port %d, enabled %d\n", __func__, addr, e->eee_enabled);
+
+ if (rtl8380_rtl8214fc_media_is_fibre(addr)) {
+ netdev_err(phydev->attached_dev, "Port %d configured for FIBRE", addr);
+ return -ENOTSUPP;
+ }
+
+ pollMask = sw_r32(RTL838X_SMI_POLL_CTRL);
+ sw_w32(0, RTL838X_SMI_POLL_CTRL);
+ rtl8380_rtl8218b_eee_set_u_boot(addr, (bool) e->eee_enabled);
+ sw_w32(pollMask, RTL838X_SMI_POLL_CTRL);
+ return 0;
+}
+
+static int rtl8380_rtl8214fc_get_eee(struct phy_device *phydev,
+ struct ethtool_eee *e)
+{
+ int addr = phydev->mdio.addr;
+
+ pr_debug("In %s port %d, enabled %d\n", __func__, addr, e->eee_enabled);
+ if (rtl8380_rtl8214fc_media_is_fibre(addr)) {
+ netdev_err(phydev->attached_dev, "Port %d configured for FIBRE", addr);
+ return -ENOTSUPP;
+ }
+
+ return rtl8380_rtl8218b_get_eee_u_boot(phydev, e);
+}
+
+static int rtl8380_rtl8218b_set_eee(struct phy_device *phydev,
+ struct ethtool_eee *e)
+{
+ u32 pollMask;
+ int addr = phydev->mdio.addr;
+
+ pr_debug("In %s, port %d, enabled %d\n", __func__, addr, e->eee_enabled);
+
+ pollMask = sw_r32(RTL838X_SMI_POLL_CTRL);
+ sw_w32(0, RTL838X_SMI_POLL_CTRL);
+ rtl8380_rtl8218b_eee_set_u_boot(addr, (bool) e->eee_enabled);
+ sw_w32(pollMask, RTL838X_SMI_POLL_CTRL);
+
+ return 0;
+}
+
+static int rtl8214c_match_phy_device(struct phy_device *phydev)
+{
+ return phydev->phy_id == PHY_ID_RTL8214C;
+}
+
+static int rtl8380_configure_rtl8214c(struct phy_device *phydev)
+{
+ u32 phy_id, val;
+ int mac = phydev->mdio.addr;
+
+ read_phy(mac, 0, 2, &val);
+ phy_id = val << 16;
+ read_phy(mac, 0, 3, &val);
+ phy_id |= val;
+ pr_debug("Phy on MAC %d: %x\n", mac, phy_id);
+
+ phydev_info(phydev, "Detected external RTL8214C\n");
+
+ /* GPHY auto conf */
+ write_phy(mac, 0xa42, 29, 0);
+ return 0;
+}
+
+static int rtl8380_configure_rtl8214fc(struct phy_device *phydev)
+{
+ u32 phy_id, val, page = 0;
+ int i, l;
+ int mac = phydev->mdio.addr;
+ struct fw_header *h;
+ u32 *rtl8380_rtl8214fc_perchip;
+ u32 *rtl8380_rtl8214fc_perport;
+
+ read_phy(mac, 0, 2, &val);
+ phy_id = val << 16;
+ read_phy(mac, 0, 3, &val);
+ phy_id |= val;
+ pr_debug("Phy on MAC %d: %x\n", mac, phy_id);
+
+ /* Read internal PHY id */
+ write_phy(mac, 0, 30, 0x0001);
+ write_phy(mac, 0, 31, 0x0a42);
+ write_phy(mac, 31, 27, 0x0002);
+ read_phy(mac, 31, 28, &val);
+ if (val != 0x6276) {
+ phydev_err(phydev, "Expected external RTL8214FC, found PHY-ID %x\n", val);
+ return -1;
+ }
+ phydev_info(phydev, "Detected external RTL8214FC\n");
+
+ h = rtl838x_request_fw(phydev, &rtl838x_8214fc_fw, FIRMWARE_838X_8214FC_1);
+ if (!h)
+ return -1;
+
+ if (h->phy != 0x8214fc00) {
+ phydev_err(phydev, "Wrong firmware file: PHY mismatch.\n");
+ return -1;
+ }
+
+ rtl8380_rtl8214fc_perchip = (void *)h + sizeof(struct fw_header)
+ + h->parts[0].start;
+
+ rtl8380_rtl8214fc_perport = (void *)h + sizeof(struct fw_header)
+ + h->parts[1].start;
+
+ /* detect phy version */
+ write_phy(mac, 0xfff, 27, 0x0004);
+ read_phy(mac, 0xfff, 28, &val);
+
+ read_phy(mac, 0, 16, &val);
+ if (val & (1 << 11))
+ rtl8380_rtl8214fc_on_off(mac, true);
+ else
+ rtl8380_phy_reset(mac);
+
+ msleep(100);
+ write_phy(mac, 0, 30, 0x0001);
+
+ i = 0;
+ while (rtl8380_rtl8214fc_perchip[i * 3]
+ && rtl8380_rtl8214fc_perchip[i * 3 + 1]) {
+ if (rtl8380_rtl8214fc_perchip[i * 3 + 1] == 0x1f)
+ page = rtl8380_rtl8214fc_perchip[i * 3 + 2];
+ if (rtl8380_rtl8214fc_perchip[i * 3 + 1] == 0x13 && page == 0x260) {
+ read_phy(mac + rtl8380_rtl8214fc_perchip[i * 3], 0x260, 13, &val);
+ val = (val & 0x1f00) | (rtl8380_rtl8214fc_perchip[i * 3 + 2]
+ & 0xe0ff);
+ write_phy(mac + rtl8380_rtl8214fc_perchip[i * 3],
+ 0xfff, rtl8380_rtl8214fc_perchip[i * 3 + 1], val);
+ } else {
+ write_phy(mac + rtl8380_rtl8214fc_perchip[i * 3],
+ 0xfff, rtl8380_rtl8214fc_perchip[i * 3 + 1],
+ rtl8380_rtl8214fc_perchip[i * 3 + 2]);
+ }
+ i++;
+ }
+
+ /* Force copper medium */
+ for (i = 0; i < 4; i++) {
+ write_phy(mac + i, 0xfff, 0x1f, 0x0000);
+ write_phy(mac + i, 0xfff, 0x1e, 0x0001);
+ }
+
+ /* Enable PHY */
+ for (i = 0; i < 4; i++) {
+ write_phy(mac + i, 0xfff, 0x1f, 0x0000);
+ write_phy(mac + i, 0xfff, 0x00, 0x1140);
+ }
+ mdelay(100);
+
+ /* Disable Autosensing */
+ for (i = 0; i < 4; i++) {
+ for (l = 0; l < 100; l++) {
+ read_phy(mac + i, 0x0a42, 0x10, &val);
+ if ((val & 0x7) >= 3)
+ break;
+ }
+ if (l >= 100) {
+ phydev_err(phydev, "Could not disable autosensing\n");
+ return -1;
+ }
+ }
+
+ /* Request patch */
+ for (i = 0; i < 4; i++) {
+ write_phy(mac + i, 0xfff, 0x1f, 0x0b82);
+ write_phy(mac + i, 0xfff, 0x10, 0x0010);
+ }
+ mdelay(300);
+
+ /* Verify patch readiness */
+ for (i = 0; i < 4; i++) {
+ for (l = 0; l < 100; l++) {
+ read_phy(mac + i, 0xb80, 0x10, &val);
+ if (val & 0x40)
+ break;
+ }
+ if (l >= 100) {
+ phydev_err(phydev, "Could not patch PHY\n");
+ return -1;
+ }
+ }
+
+ /* Use Broadcast ID method for patching */
+ write_phy(mac, 0xfff, 0x1f, 0x0000);
+ write_phy(mac, 0xfff, 0x1d, 0x0008);
+ write_phy(mac, 0xfff, 0x1f, 0x0266);
+ write_phy(mac, 0xfff, 0x16, 0xff00 + mac);
+ write_phy(mac, 0xfff, 0x1f, 0x0000);
+ write_phy(mac, 0xfff, 0x1d, 0x0000);
+ mdelay(1);
+
+ i = 0;
+ while (rtl8380_rtl8214fc_perport[i * 2]) {
+ write_phy(mac, 0xfff, rtl8380_rtl8214fc_perport[i * 2],
+ rtl8380_rtl8214fc_perport[i * 2 + 1]);
+ i++;
+ }
+
+ /*Disable broadcast ID*/
+ write_phy(mac, 0xfff, 0x1f, 0x0000);
+ write_phy(mac, 0xfff, 0x1d, 0x0008);
+ write_phy(mac, 0xfff, 0x1f, 0x0266);
+ write_phy(mac, 0xfff, 0x16, 0x00 + mac);
+ write_phy(mac, 0xfff, 0x1f, 0x0000);
+ write_phy(mac, 0xfff, 0x1d, 0x0000);
+ mdelay(1);
+
+ /* Auto medium selection */
+ for (i = 0; i < 4; i++) {
+ write_phy(mac + i, 0xfff, 0x1f, 0x0000);
+ write_phy(mac + i, 0xfff, 0x1e, 0x0000);
+ }
+
+ return 0;
+}
+
+static int rtl8214fc_match_phy_device(struct phy_device *phydev)
+{
+ int addr = phydev->mdio.addr;
+
+ return phydev->phy_id == PHY_ID_RTL8214FC && addr >= 24;
+}
+
+static int rtl8380_configure_serdes(struct phy_device *phydev)
+{
+ u32 v;
+ u32 sds_conf_value;
+ int i;
+ struct fw_header *h;
+ u32 *rtl8380_sds_take_reset;
+ u32 *rtl8380_sds_common;
+ u32 *rtl8380_sds01_qsgmii_6275b;
+ u32 *rtl8380_sds23_qsgmii_6275b;
+ u32 *rtl8380_sds4_fiber_6275b;
+ u32 *rtl8380_sds5_fiber_6275b;
+ u32 *rtl8380_sds_reset;
+ u32 *rtl8380_sds_release_reset;
+
+ phydev_info(phydev, "Detected internal RTL8380 SERDES\n");
+
+ h = rtl838x_request_fw(phydev, &rtl838x_8218b_fw, FIRMWARE_838X_8380_1);
+ if (!h)
+ return -1;
+
+ if (h->magic != 0x83808380) {
+ phydev_err(phydev, "Wrong firmware file: magic number mismatch.\n");
+ return -1;
+ }
+
+ rtl8380_sds_take_reset = (void *)h + sizeof(struct fw_header)
+ + h->parts[0].start;
+
+ rtl8380_sds_common = (void *)h + sizeof(struct fw_header)
+ + h->parts[1].start;
+
+ rtl8380_sds01_qsgmii_6275b = (void *)h + sizeof(struct fw_header)
+ + h->parts[2].start;
+
+ rtl8380_sds23_qsgmii_6275b = (void *)h + sizeof(struct fw_header)
+ + h->parts[3].start;
+
+ rtl8380_sds4_fiber_6275b = (void *)h + sizeof(struct fw_header)
+ + h->parts[4].start;
+
+ rtl8380_sds5_fiber_6275b = (void *)h + sizeof(struct fw_header)
+ + h->parts[5].start;
+
+ rtl8380_sds_reset = (void *)h + sizeof(struct fw_header)
+ + h->parts[6].start;
+
+ rtl8380_sds_release_reset = (void *)h + sizeof(struct fw_header)
+ + h->parts[7].start;
+
+ /* Back up serdes power off value */
+ sds_conf_value = sw_r32(RTL838X_SDS_CFG_REG);
+ pr_info("SDS power down value: %x\n", sds_conf_value);
+
+ /* take serdes into reset */
+ i = 0;
+ while (rtl8380_sds_take_reset[2 * i]) {
+ sw_w32(rtl8380_sds_take_reset[2 * i + 1], rtl8380_sds_take_reset[2 * i]);
+ i++;
+ udelay(1000);
+ }
+
+ /* apply common serdes patch */
+ i = 0;
+ while (rtl8380_sds_common[2 * i]) {
+ sw_w32(rtl8380_sds_common[2 * i + 1], rtl8380_sds_common[2 * i]);
+ i++;
+ udelay(1000);
+ }
+
+ /* internal R/W enable */
+ sw_w32(3, RTL838X_INT_RW_CTRL);
+
+ /* SerDes ports 4 and 5 are FIBRE ports */
+ sw_w32_mask(0x7 | 0x38, 1 | (1 << 3), RTL838X_INT_MODE_CTRL);
+
+ /* SerDes module settings, SerDes 0-3 are QSGMII */
+ v = 0x6 << 25 | 0x6 << 20 | 0x6 << 15 | 0x6 << 10;
+ /* SerDes 4 and 5 are 1000BX FIBRE */
+ v |= 0x4 << 5 | 0x4;
+ sw_w32(v, RTL838X_SDS_MODE_SEL);
+
+ pr_info("PLL control register: %x\n", sw_r32(RTL838X_PLL_CML_CTRL));
+ sw_w32_mask(0xfffffff0, 0xaaaaaaaf & 0xf, RTL838X_PLL_CML_CTRL);
+ i = 0;
+ while (rtl8380_sds01_qsgmii_6275b[2 * i]) {
+ sw_w32(rtl8380_sds01_qsgmii_6275b[2 * i + 1],
+ rtl8380_sds01_qsgmii_6275b[2 * i]);
+ i++;
+ }
+
+ i = 0;
+ while (rtl8380_sds23_qsgmii_6275b[2 * i]) {
+ sw_w32(rtl8380_sds23_qsgmii_6275b[2 * i + 1], rtl8380_sds23_qsgmii_6275b[2 * i]);
+ i++;
+ }
+
+ i = 0;
+ while (rtl8380_sds4_fiber_6275b[2 * i]) {
+ sw_w32(rtl8380_sds4_fiber_6275b[2 * i + 1], rtl8380_sds4_fiber_6275b[2 * i]);
+ i++;
+ }
+
+ i = 0;
+ while (rtl8380_sds5_fiber_6275b[2 * i]) {
+ sw_w32(rtl8380_sds5_fiber_6275b[2 * i + 1], rtl8380_sds5_fiber_6275b[2 * i]);
+ i++;
+ }
+
+ i = 0;
+ while (rtl8380_sds_reset[2 * i]) {
+ sw_w32(rtl8380_sds_reset[2 * i + 1], rtl8380_sds_reset[2 * i]);
+ i++;
+ }
+
+ i = 0;
+ while (rtl8380_sds_release_reset[2 * i]) {
+ sw_w32(rtl8380_sds_release_reset[2 * i + 1], rtl8380_sds_release_reset[2 * i]);
+ i++;
+ }
+
+ pr_info("SDS power down value now: %x\n", sw_r32(RTL838X_SDS_CFG_REG));
+ sw_w32(sds_conf_value, RTL838X_SDS_CFG_REG);
+
+ pr_info("Configuration of SERDES done\n");
+ return 0;
+}
+
+static int rtl8214fc_phy_probe(struct phy_device *phydev)
+{
+ struct device *dev = &phydev->mdio.dev;
+ struct rtl838x_phy_priv *priv;
+ int addr = phydev->mdio.addr;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->name = "RTL8214FC";
+
+ /* All base addresses of the PHYs start at multiples of 8 */
+ if (!(addr % 8)) {
+ /* Configuration must be done whil patching still possible */
+ return rtl8380_configure_rtl8214fc(phydev);
+ }
+ return 0;
+}
+
+static int rtl8214c_phy_probe(struct phy_device *phydev)
+{
+ struct device *dev = &phydev->mdio.dev;
+ struct rtl838x_phy_priv *priv;
+ int addr = phydev->mdio.addr;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->name = "RTL8214C";
+
+ /* All base addresses of the PHYs start at multiples of 8 */
+ if (!(addr % 8)) {
+ /* Configuration must be done whil patching still possible */
+ return rtl8380_configure_rtl8214c(phydev);
+ }
+ return 0;
+}
+
+static int rtl8218b_ext_phy_probe(struct phy_device *phydev)
+{
+ struct device *dev = &phydev->mdio.dev;
+ struct rtl838x_phy_priv *priv;
+ int addr = phydev->mdio.addr;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->name = "RTL8218B (external)";
+
+ /* All base addresses of the PHYs start at multiples of 8 */
+ if (!(addr % 8)) {
+ /* Configuration must be done while patching still possible */
+ return rtl8380_configure_ext_rtl8218b(phydev);
+ }
+ return 0;
+}
+
+static int rtl8218b_int_phy_probe(struct phy_device *phydev)
+{
+ struct device *dev = &phydev->mdio.dev;
+ struct rtl838x_phy_priv *priv;
+ int addr = phydev->mdio.addr;
+
+ if (soc_info.family != RTL8380_FAMILY_ID)
+ return -ENODEV;
+ if (addr >= 24)
+ return -ENODEV;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->name = "RTL8218B (internal)";
+
+ /* All base addresses of the PHYs start at multiples of 8 */
+ if (!(addr % 8)) {
+ /* Configuration must be done while patching still possible */
+ return rtl8380_configure_int_rtl8218b(phydev);
+ }
+ return 0;
+}
+
+static int rtl838x_serdes_probe(struct phy_device *phydev)
+{
+ struct device *dev = &phydev->mdio.dev;
+ struct rtl838x_phy_priv *priv;
+ int addr = phydev->mdio.addr;
+
+ if (soc_info.family != RTL8380_FAMILY_ID)
+ return -ENODEV;
+ if (addr < 24)
+ return -ENODEV;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->name = "RTL8380 Serdes";
+
+ /* On the RTL8380M, PHYs 24-27 connect to the internal SerDes */
+ if (soc_info.id == 0x8380) {
+ if (addr == 24)
+ return rtl8380_configure_serdes(phydev);
+ return 0;
+ }
+ return -ENODEV;
+}
+
+static int rtl8390_serdes_probe(struct phy_device *phydev)
+{
+ struct device *dev = &phydev->mdio.dev;
+ struct rtl838x_phy_priv *priv;
+ int addr = phydev->mdio.addr;
+
+ if (soc_info.family != RTL8390_FAMILY_ID)
+ return -ENODEV;
+
+ if (addr < 24)
+ return -ENODEV;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->name = "RTL8390 Serdes";
+ return rtl8390_configure_generic(phydev);
+}
+
+static struct phy_driver rtl838x_phy_driver[] = {
+ {
+ PHY_ID_MATCH_MODEL(PHY_ID_RTL8214FC),
+ .name = "REATLTEK RTL8214C",
+ .features = PHY_GBIT_FEATURES,
+ .match_phy_device = rtl8214c_match_phy_device,
+ .probe = rtl8214c_phy_probe,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
+ .set_loopback = genphy_loopback,
+ },
+ {
+ PHY_ID_MATCH_MODEL(PHY_ID_RTL8214FC),
+ .name = "REATLTEK RTL8214FC",
+ .features = PHY_GBIT_FIBRE_FEATURES,
+ .match_phy_device = rtl8214fc_match_phy_device,
+ .probe = rtl8214fc_phy_probe,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
+ .set_loopback = genphy_loopback,
+ .read_mmd = rtl8380_rtl8218b_read_mmd,
+ .write_mmd = rtl8380_rtl8218b_write_mmd,
+ .set_port = rtl8380_rtl8214fc_set_port,
+ .get_port = rtl8380_rtl8214fc_get_port,
+ .set_eee = rtl8380_rtl8214fc_set_eee,
+ .get_eee = rtl8380_rtl8214fc_get_eee,
+ },
+ {
+ PHY_ID_MATCH_MODEL(PHY_ID_RTL8218B_E),
+ .name = "REATLTEK RTL8218B (external)",
+ .features = PHY_GBIT_FEATURES,
+ .match_phy_device = rtl8218b_ext_match_phy_device,
+ .probe = rtl8218b_ext_phy_probe,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
+ .set_loopback = genphy_loopback,
+ .read_mmd = rtl8380_rtl8218b_read_mmd,
+ .write_mmd = rtl8380_rtl8218b_write_mmd,
+ .set_eee = rtl8380_rtl8218b_set_eee,
+ .get_eee = rtl8380_rtl8218b_get_eee_u_boot,
+ },
+ {
+ PHY_ID_MATCH_MODEL(PHY_ID_RTL8218B_I),
+ .name = "REATLTEK RTL8218B (internal)",
+ .features = PHY_GBIT_FEATURES,
+ .probe = rtl8218b_int_phy_probe,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
+ .set_loopback = genphy_loopback,
+ .read_mmd = rtl8380_rtl8218b_read_mmd,
+ .write_mmd = rtl8380_rtl8218b_write_mmd,
+ .set_eee = rtl8380_rtl8218b_set_eee,
+ .get_eee = rtl8380_rtl8218b_get_eee_u_boot,
+ },
+ {
+ PHY_ID_MATCH_MODEL(PHY_ID_RTL8218B_I),
+ .name = "REATLTEK RTL8380 SERDES",
+ .features = PHY_GBIT_FIBRE_FEATURES,
+ .probe = rtl838x_serdes_probe,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
+ .set_loopback = genphy_loopback,
+ .read_mmd = rtl8380_rtl8218b_read_mmd,
+ .write_mmd = rtl8380_rtl8218b_write_mmd,
+ },
+ {
+ PHY_ID_MATCH_MODEL(PHY_ID_RTL8390_GENERIC),
+ .name = "REATLTEK RTL8390 Generic",
+ .features = PHY_GBIT_FIBRE_FEATURES,
+ .probe = rtl8390_serdes_probe,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
+ .set_loopback = genphy_loopback,
+ }
+};
+
+module_phy_driver(rtl838x_phy_driver);
+
+static struct mdio_device_id __maybe_unused rtl838x_tbl[] = {
+ { PHY_ID_MATCH_MODEL(PHY_ID_RTL8214FC) },
+ { }
+};
+
+MODULE_DEVICE_TABLE(mdio, rtl838x_tbl);
+
+MODULE_AUTHOR("B. Koblitz");
+MODULE_DESCRIPTION("RTL838x PHY driver");
+MODULE_LICENSE("GPL");
diff --git a/target/linux/rtl838x/files-5.4/drivers/net/dsa/rtl838x_sw.c b/target/linux/rtl838x/files-5.4/drivers/net/dsa/rtl838x_sw.c
new file mode 100644
index 0000000000..7f6c2d6a29
--- /dev/null
+++ b/target/linux/rtl838x/files-5.4/drivers/net/dsa/rtl838x_sw.c
@@ -0,0 +1,2150 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/etherdevice.h>
+#include <linux/if_bridge.h>
+#include <linux/iopoll.h>
+#include <linux/mdio.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/of_mdio.h>
+#include <linux/of_net.h>
+#include <linux/of_platform.h>
+#include <linux/phylink.h>
+#include <linux/phy_fixed.h>
+#include <net/dsa.h>
+
+#include <asm/mach-rtl838x/mach-rtl838x.h>
+#include "rtl838x.h"
+
+#define RTL8380_VERSION_A 'A'
+#define RTL8390_VERSION_A 'A'
+#define RTL8380_VERSION_B 'B'
+
+DEFINE_MUTEX(smi_lock);
+
+#define MIB_DESC(_size, _offset, _name) {.size = _size, .offset = _offset, .name = _name}
+struct rtl838x_mib_desc {
+ unsigned int size;
+ unsigned int offset;
+ const char *name;
+};
+
+inline void rtl838x_mask_port_reg(u64 clear, u64 set, int reg)
+{
+ sw_w32_mask((u32)clear, (u32)set, reg);
+}
+
+inline void rtl839x_mask_port_reg(u64 clear, u64 set, int reg)
+{
+ sw_w32_mask((u32) (clear >> 32), (u32) (set >> 32), reg);
+ sw_w32_mask((u32) (clear & 0xffffffff), (u32) (set & 0xffffffff), reg + 4);
+}
+
+inline void rtl838x_set_port_reg(u64 set, int reg)
+{
+ sw_w32(set, reg);
+}
+
+inline void rtl839x_set_port_reg(u64 set, int reg)
+{
+ sw_w32(set >> 32, reg);
+ sw_w32(set & 0xffffffff, reg + 4);
+}
+
+inline u64 rtl838x_get_port_reg(int reg)
+{
+ return ((u64) sw_r32(reg));
+}
+
+inline u64 rtl839x_get_port_reg(int reg)
+{
+ u64 v = sw_r32(reg);
+
+ v <<= 32;
+ v |= sw_r32(reg + 4);
+ return v;
+}
+
+inline int rtl838x_stat_port_std_mib(int p)
+{
+ return RTL838X_STAT_PORT_STD_MIB + (p << 8);
+}
+
+inline int rtl839x_stat_port_std_mib(int p)
+{
+ return RTL839X_STAT_PORT_STD_MIB + (p << 8);
+}
+
+inline void rtl838x_mask_port_iso_ctrl(u64 clear, u64 set, int port)
+{
+ sw_w32_mask(clear, set, RTL838X_PORT_ISO_CTRL(port));
+}
+
+inline void rtl839x_mask_port_iso_ctrl(u64 clear, u64 set, int port)
+{
+ sw_w32_mask(clear >> 32, set >> 32, RTL839X_PORT_ISO_CTRL(port));
+ sw_w32_mask(clear & 0xffffffff, set & 0xffffffff,
+ RTL839X_PORT_ISO_CTRL(port) + 4);
+}
+
+inline void rtl838x_set_port_iso_ctrl(u64 set, int port)
+{
+ sw_w32(set, RTL838X_PORT_ISO_CTRL(port));
+}
+
+inline void rtl839x_set_port_iso_ctrl(u64 set, int port)
+{
+ sw_w32(set >> 32, RTL839X_PORT_ISO_CTRL(port));
+ sw_w32(set & 0xffffffff, RTL839X_PORT_ISO_CTRL(port) + 4);
+}
+
+inline void rtl838x_exec_tbl0_cmd(u32 cmd)
+{
+ sw_w32(cmd, RTL838X_TBL_ACCESS_CTRL_0);
+ do { } while (sw_r32(RTL838X_TBL_ACCESS_CTRL_0) & (1 << 15));
+}
+
+inline void rtl839x_exec_tbl0_cmd(u32 cmd)
+{
+ sw_w32(cmd, RTL839X_TBL_ACCESS_CTRL_0);
+ do { } while (sw_r32(RTL839X_TBL_ACCESS_CTRL_0) & (1 << 16));
+}
+
+inline void rtl838x_exec_tbl1_cmd(u32 cmd)
+{
+ sw_w32(cmd, RTL838X_TBL_ACCESS_CTRL_1);
+ do { } while (sw_r32(RTL838X_TBL_ACCESS_CTRL_1) & (1 << 15));
+}
+
+inline void rtl839x_exec_tbl1_cmd(u32 cmd)
+{
+ sw_w32(cmd, RTL839X_TBL_ACCESS_CTRL_1);
+ do { } while (sw_r32(RTL839X_TBL_ACCESS_CTRL_1) & (1 << 16));
+}
+
+inline int rtl838x_tbl_access_data_0(int i)
+{
+ return RTL838X_TBL_ACCESS_DATA_0(i);
+}
+
+inline int rtl839x_tbl_access_data_0(int i)
+{
+ return RTL839X_TBL_ACCESS_DATA_0(i);
+}
+
+static void rtl839x_vlan_tables_read(u32 vlan, struct rtl838x_vlan_info *info)
+{
+ u32 cmd;
+ u64 v;
+
+ cmd = 1 << 16 /* Execute cmd */
+ | 0 << 15 /* Read */
+ | 0 << 12 /* Table type 0b000 */
+ | (vlan & 0xfff);
+ rtl839x_exec_tbl0_cmd(cmd);
+
+ v = sw_r32(RTL838X_TBL_ACCESS_DATA_0(0));
+ v <<= 32;
+ v |= sw_r32(RTL838X_TBL_ACCESS_DATA_0(1));
+ info->tagged_ports = v >> 11;
+ info->vlan_conf = (v & 0x7ff) << 2;
+ info->vlan_conf |= sw_r32(RTL838X_TBL_ACCESS_DATA_0(1)) >> 30;
+
+ cmd = 1 << 16 /* Execute cmd */
+ | 0 << 15 /* Read */
+ | 0 << 12 /* Table type 0b000 */
+ | (vlan & 0xfff);
+ rtl839x_exec_tbl1_cmd(cmd);
+ v = sw_r32(RTL838X_TBL_ACCESS_DATA_1(0));
+ v <<= 32;
+ v |= sw_r32(RTL838X_TBL_ACCESS_DATA_1(1));
+ info->untagged_ports = v >> 11;
+}
+
+static void rtl838x_vlan_tables_read(u32 vlan, struct rtl838x_vlan_info *info)
+{
+ u32 cmd;
+
+ cmd = 1 << 15 /* Execute cmd */
+ | 1 << 14 /* Read */
+ | 0 << 12 /* Table type 0b00 */
+ | (vlan & 0xfff);
+ rtl838x_exec_tbl0_cmd(cmd);
+ info->tagged_ports = sw_r32(RTL838X_TBL_ACCESS_DATA_0(0));
+ info->vlan_conf = sw_r32(RTL838X_TBL_ACCESS_DATA_0(1));
+
+ cmd = 1 << 15 /* Execute cmd */
+ | 1 << 14 /* Read */
+ | 0 << 12 /* Table type 0b00 */
+ | (vlan & 0xfff);
+ rtl838x_exec_tbl1_cmd(cmd);
+ info->untagged_ports = sw_r32(RTL838X_TBL_ACCESS_DATA_1(0));
+}
+
+static void rtl839x_vlan_set_tagged(u32 vlan, u64 portmask, u32 conf)
+{
+ u32 cmd = 1 << 16 /* Execute cmd */
+ | 1 << 15 /* Write */
+ | 0 << 12 /* Table type 0b00 */
+ | (vlan & 0xfff);
+ u64 v = portmask << 11;
+
+ v |= (conf >> 2) & 0x7ff;
+ sw_w64(v, RTL838X_TBL_ACCESS_DATA_0(0));
+ sw_w32(conf << 30, RTL838X_TBL_ACCESS_DATA_0(2));
+ rtl839x_exec_tbl0_cmd(cmd);
+}
+
+static void rtl838x_vlan_set_tagged(u32 vlan, u64 portmask, u32 conf)
+{
+ u32 cmd = 1 << 15 /* Execute cmd */
+ | 0 << 14 /* Write */
+ | 0 << 12 /* Table type 0b00 */
+ | (vlan & 0xfff);
+
+ sw_w32(portmask, RTL838X_TBL_ACCESS_DATA_0(0));
+ sw_w32(conf, RTL838X_TBL_ACCESS_DATA_0(1));
+ rtl838x_exec_tbl0_cmd(cmd);
+}
+
+static void rtl839x_vlan_set_untagged(u32 vlan, u64 portmask)
+{
+ u32 cmd = 1 << 16 /* Execute cmd */
+ | 1 << 15 /* Write */
+ | 0 << 12 /* Table type 0b00 */
+ | (vlan & 0xfff);
+ sw_w64(portmask << 11, RTL838X_TBL_ACCESS_DATA_1(0));
+ rtl839x_exec_tbl1_cmd(cmd);
+}
+
+static void rtl838x_vlan_set_untagged(u32 vlan, u64 portmask)
+{
+ u32 cmd = 1 << 15 /* Execute cmd */
+ | 0 << 14 /* Write */
+ | 0 << 12 /* Table type 0b00 */
+ | (vlan & 0xfff);
+ sw_w32(portmask & 0x1fffffff, RTL838X_TBL_ACCESS_DATA_1(0));
+ rtl838x_exec_tbl1_cmd(cmd);
+}
+
+static inline int rtl838x_mac_force_mode_ctrl(int p)
+{
+ return RTL838X_MAC_FORCE_MODE_CTRL + (p << 2);
+}
+
+static inline int rtl839x_mac_force_mode_ctrl(int p)
+{
+ return RTL839X_MAC_FORCE_MODE_CTRL + (p << 2);
+}
+
+static const struct rtl838x_reg rtl838x_reg = {
+ .mask_port_reg = rtl838x_mask_port_reg,
+ .set_port_reg = rtl838x_set_port_reg,
+ .get_port_reg = rtl838x_get_port_reg,
+ .stat_port_rst = RTL838X_STAT_PORT_RST,
+ .stat_rst = RTL838X_STAT_RST,
+ .stat_port_std_mib = rtl838x_stat_port_std_mib,
+ .mask_port_iso_ctrl = rtl838x_mask_port_iso_ctrl,
+ .set_port_iso_ctrl = rtl838x_set_port_iso_ctrl,
+ .l2_ctrl_0 = RTL838X_L2_CTRL_0,
+ .l2_ctrl_1 = RTL838X_L2_CTRL_1,
+ .l2_port_aging_out = RTL838X_L2_PORT_AGING_OUT,
+ .smi_poll_ctrl = RTL838X_SMI_POLL_CTRL,
+ .l2_tbl_flush_ctrl = RTL838X_L2_TBL_FLUSH_CTRL,
+ .exec_tbl0_cmd = rtl838x_exec_tbl0_cmd,
+ .exec_tbl1_cmd = rtl838x_exec_tbl1_cmd,
+ .tbl_access_data_0 = rtl838x_tbl_access_data_0,
+ .isr_glb_src = RTL838X_ISR_GLB_SRC,
+ .isr_port_link_sts_chg = RTL838X_ISR_PORT_LINK_STS_CHG,
+ .imr_port_link_sts_chg = RTL838X_IMR_PORT_LINK_STS_CHG,
+ .imr_glb = RTL838X_IMR_GLB,
+ .vlan_tables_read = rtl838x_vlan_tables_read,
+ .vlan_set_tagged = rtl838x_vlan_set_tagged,
+ .vlan_set_untagged = rtl838x_vlan_set_untagged,
+ .mac_force_mode_ctrl = rtl838x_mac_force_mode_ctrl,
+ .rst_glb_ctrl = RTL838X_RST_GLB_CTRL_0,
+};
+
+static const struct rtl838x_reg rtl839x_reg = {
+ .mask_port_reg = rtl839x_mask_port_reg,
+ .set_port_reg = rtl839x_set_port_reg,
+ .get_port_reg = rtl839x_get_port_reg,
+ .stat_port_rst = RTL839X_STAT_PORT_RST,
+ .stat_rst = RTL839X_STAT_RST,
+ .stat_port_std_mib = rtl839x_stat_port_std_mib,
+ .mask_port_iso_ctrl = rtl839x_mask_port_iso_ctrl,
+ .set_port_iso_ctrl = rtl839x_set_port_iso_ctrl,
+ .l2_ctrl_0 = RTL839X_L2_CTRL_0,
+ .l2_ctrl_1 = RTL839X_L2_CTRL_1,
+ .l2_port_aging_out = RTL839X_L2_PORT_AGING_OUT,
+ .smi_poll_ctrl = RTL839X_SMI_PORT_POLLING_CTRL,
+ .l2_tbl_flush_ctrl = RTL839X_L2_TBL_FLUSH_CTRL,
+ .exec_tbl0_cmd = rtl839x_exec_tbl0_cmd,
+ .exec_tbl1_cmd = rtl839x_exec_tbl1_cmd,
+ .tbl_access_data_0 = rtl839x_tbl_access_data_0,
+ .isr_glb_src = RTL839X_ISR_GLB_SRC,
+ .isr_port_link_sts_chg = RTL839X_ISR_PORT_LINK_STS_CHG,
+ .imr_port_link_sts_chg = RTL839X_IMR_PORT_LINK_STS_CHG,
+ .imr_glb = RTL839X_IMR_GLB,
+ .vlan_tables_read = rtl839x_vlan_tables_read,
+ .vlan_set_tagged = rtl839x_vlan_set_tagged,
+ .vlan_set_untagged = rtl839x_vlan_set_untagged,
+ .mac_force_mode_ctrl = rtl839x_mac_force_mode_ctrl,
+ .rst_glb_ctrl = RTL839X_RST_GLB_CTRL,
+};
+
+static const struct rtl838x_mib_desc rtl838x_mib[] = {
+ MIB_DESC(2, 0xf8, "ifInOctets"),
+ MIB_DESC(2, 0xf0, "ifOutOctets"),
+ MIB_DESC(1, 0xec, "dot1dTpPortInDiscards"),
+ MIB_DESC(1, 0xe8, "ifInUcastPkts"),
+ MIB_DESC(1, 0xe4, "ifInMulticastPkts"),
+ MIB_DESC(1, 0xe0, "ifInBroadcastPkts"),
+ MIB_DESC(1, 0xdc, "ifOutUcastPkts"),
+ MIB_DESC(1, 0xd8, "ifOutMulticastPkts"),
+ MIB_DESC(1, 0xd4, "ifOutBroadcastPkts"),
+ MIB_DESC(1, 0xd0, "ifOutDiscards"),
+ MIB_DESC(1, 0xcc, ".3SingleCollisionFrames"),
+ MIB_DESC(1, 0xc8, ".3MultipleCollisionFrames"),
+ MIB_DESC(1, 0xc4, ".3DeferredTransmissions"),
+ MIB_DESC(1, 0xc0, ".3LateCollisions"),
+ MIB_DESC(1, 0xbc, ".3ExcessiveCollisions"),
+ MIB_DESC(1, 0xb8, ".3SymbolErrors"),
+ MIB_DESC(1, 0xb4, ".3ControlInUnknownOpcodes"),
+ MIB_DESC(1, 0xb0, ".3InPauseFrames"),
+ MIB_DESC(1, 0xac, ".3OutPauseFrames"),
+ MIB_DESC(1, 0xa8, "DropEvents"),
+ MIB_DESC(1, 0xa4, "tx_BroadcastPkts"),
+ MIB_DESC(1, 0xa0, "tx_MulticastPkts"),
+ MIB_DESC(1, 0x9c, "CRCAlignErrors"),
+ MIB_DESC(1, 0x98, "tx_UndersizePkts"),
+ MIB_DESC(1, 0x94, "rx_UndersizePkts"),
+ MIB_DESC(1, 0x90, "rx_UndersizedropPkts"),
+ MIB_DESC(1, 0x8c, "tx_OversizePkts"),
+ MIB_DESC(1, 0x88, "rx_OversizePkts"),
+ MIB_DESC(1, 0x84, "Fragments"),
+ MIB_DESC(1, 0x80, "Jabbers"),
+ MIB_DESC(1, 0x7c, "Collisions"),
+ MIB_DESC(1, 0x78, "tx_Pkts64Octets"),
+ MIB_DESC(1, 0x74, "rx_Pkts64Octets"),
+ MIB_DESC(1, 0x70, "tx_Pkts65to127Octets"),
+ MIB_DESC(1, 0x6c, "rx_Pkts65to127Octets"),
+ MIB_DESC(1, 0x68, "tx_Pkts128to255Octets"),
+ MIB_DESC(1, 0x64, "rx_Pkts128to255Octets"),
+ MIB_DESC(1, 0x60, "tx_Pkts256to511Octets"),
+ MIB_DESC(1, 0x5c, "rx_Pkts256to511Octets"),
+ MIB_DESC(1, 0x58, "tx_Pkts512to1023Octets"),
+ MIB_DESC(1, 0x54, "rx_Pkts512to1023Octets"),
+ MIB_DESC(1, 0x50, "tx_Pkts1024to1518Octets"),
+ MIB_DESC(1, 0x4c, "rx_StatsPkts1024to1518Octets"),
+ MIB_DESC(1, 0x48, "tx_Pkts1519toMaxOctets"),
+ MIB_DESC(1, 0x44, "rx_Pkts1519toMaxOctets"),
+ MIB_DESC(1, 0x40, "rxMacDiscards")
+};
+
+static irqreturn_t rtl838x_switch_irq(int irq, void *dev_id)
+{
+ struct dsa_switch *ds = dev_id;
+ u32 status = sw_r32(RTL838X_ISR_GLB_SRC);
+ u32 ports = sw_r32(RTL838X_ISR_PORT_LINK_STS_CHG);
+ u32 link;
+ int i;
+
+ /* Clear status */
+ sw_w32(ports, RTL838X_ISR_PORT_LINK_STS_CHG);
+ pr_info("Link change: status: %x, ports %x\n", status, ports);
+
+ for (i = 0; i < 28; i++) {
+ if (ports & (1 << i)) {
+ link = sw_r32(RTL838X_MAC_LINK_STS);
+ if (link & (1 << i))
+ dsa_port_phylink_mac_change(ds, i, true);
+ else
+ dsa_port_phylink_mac_change(ds, i, false);
+ }
+ }
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t rtl839x_switch_irq(int irq, void *dev_id)
+{
+ struct dsa_switch *ds = dev_id;
+ u32 status = sw_r32(RTL839X_ISR_GLB_SRC);
+ u64 ports = sw_r64(RTL839X_ISR_PORT_LINK_STS_CHG);
+ u64 link;
+ int i;
+
+ /* Clear status */
+ sw_w64(ports, RTL839X_ISR_PORT_LINK_STS_CHG);
+ pr_info("Link change: status: %x, ports %llx\n", status, ports);
+
+ for (i = 0; i < 52; i++) {
+ if (ports & (1 << i)) {
+ link = sw_r64(RTL839X_MAC_LINK_STS);
+ if (link & (1 << i))
+ dsa_port_phylink_mac_change(ds, i, true);
+ else
+ dsa_port_phylink_mac_change(ds, i, false);
+ }
+ }
+ return IRQ_HANDLED;
+}
+
+int rtl8380_sds_power(int mac, int val)
+{
+ u32 mode = (val == 1) ? 0x4 : 0x9;
+ u32 offset = (mac == 24) ? 5 : 0;
+
+ if ((mac != 24) && (mac != 26)) {
+ pr_err("%s: not a fibre port: %d\n", __func__, mac);
+ return -1;
+ }
+
+ sw_w32_mask(0x1f << offset, mode << offset, RTL838X_SDS_MODE_SEL);
+
+ rtl8380_sds_rst(mac);
+
+ return 0;
+}
+
+static int rtl838x_smi_wait_op(int timeout)
+{
+ do {
+ timeout--;
+ udelay(10);
+ } while ((sw_r32(RTL838X_SMI_ACCESS_PHY_CTRL_1) & 0x1) && (timeout >= 0));
+ if (timeout <= 0)
+ return -1;
+ return 0;
+}
+
+/*
+ * Write to a register in a page of the PHY
+ */
+int rtl838x_write_phy(u32 port, u32 page, u32 reg, u32 val)
+{
+ u32 v;
+ u32 park_page;
+
+ val &= 0xffff;
+ if (port > 31 || page > 4095 || reg > 31)
+ return -ENOTSUPP;
+
+ mutex_lock(&smi_lock);
+ if (rtl838x_smi_wait_op(10000))
+ goto timeout;
+
+ sw_w32(1 << port, RTL838X_SMI_ACCESS_PHY_CTRL_0);
+ mdelay(10);
+
+ sw_w32_mask(0xffff0000, val << 16, RTL838X_SMI_ACCESS_PHY_CTRL_2);
+
+ park_page = sw_r32(RTL838X_SMI_ACCESS_PHY_CTRL_1) & ((0x1f << 15) | 0x2);
+ v = reg << 20 | page << 3 | 0x4;
+ sw_w32(v | park_page, RTL838X_SMI_ACCESS_PHY_CTRL_1);
+ sw_w32_mask(0, 1, RTL838X_SMI_ACCESS_PHY_CTRL_1);
+
+ if (rtl838x_smi_wait_op(10000))
+ goto timeout;
+
+ mutex_unlock(&smi_lock);
+ return 0;
+
+timeout:
+ mutex_unlock(&smi_lock);
+ return -ETIMEDOUT;
+}
+
+int rtl839x_write_phy(u32 port, u32 page, u32 reg, u32 val)
+{
+ u32 v;
+ int err = 0;
+
+ val &= 0xffff;
+ if (port > 63 || page > 4095 || reg > 31)
+ return -ENOTSUPP;
+
+ mutex_lock(&smi_lock);
+ /* Clear both port registers */
+ sw_w32(0, RTL839X_PHYREG_PORT_CTRL(0));
+ sw_w32(0, RTL839X_PHYREG_PORT_CTRL(0) + 4);
+ sw_w32_mask(0, 1 << port, RTL839X_PHYREG_PORT_CTRL(port));
+
+ sw_w32_mask(0xffff0000, val << 16, RTL839X_PHYREG_DATA_CTRL);
+
+ v = reg << 5 | page << 10 | ((page == 0x1fff) ? 0x1f : 0) << 23;
+ sw_w32(v, RTL839X_PHYREG_ACCESS_CTRL);
+
+ sw_w32(0x1ff, RTL839X_PHYREG_CTRL);
+
+ v |= 1 << 3 | 1; /* Write operation and execute */
+ sw_w32(v, RTL839X_PHYREG_ACCESS_CTRL);
+
+ do {
+ } while (sw_r32(RTL839X_PHYREG_ACCESS_CTRL) & 0x1);
+
+ if (sw_r32(RTL839X_PHYREG_ACCESS_CTRL) & 0x2)
+ err = -EIO;
+
+ mutex_unlock(&smi_lock);
+ return err;
+}
+
+/*
+ * Reads a register in a page from the PHY
+ */
+int rtl838x_read_phy(u32 port, u32 page, u32 reg, u32 *val)
+{
+ u32 v;
+ u32 park_page;
+
+ if (port > 31 || page > 4095 || reg > 31)
+ return -ENOTSUPP;
+
+ mutex_lock(&smi_lock);
+
+ if (rtl838x_smi_wait_op(10000))
+ goto timeout;
+
+ sw_w32_mask(0xffff0000, port << 16, RTL838X_SMI_ACCESS_PHY_CTRL_2);
+
+ park_page = sw_r32(RTL838X_SMI_ACCESS_PHY_CTRL_1) & ((0x1f << 15) | 0x2);
+ v = reg << 20 | page << 3;
+ sw_w32(v | park_page, RTL838X_SMI_ACCESS_PHY_CTRL_1);
+ sw_w32_mask(0, 1, RTL838X_SMI_ACCESS_PHY_CTRL_1);
+
+ if (rtl838x_smi_wait_op(10000))
+ goto timeout;
+
+ *val = sw_r32(RTL838X_SMI_ACCESS_PHY_CTRL_2) & 0xffff;
+
+ mutex_unlock(&smi_lock);
+ return 0;
+
+timeout:
+ mutex_unlock(&smi_lock);
+ return -ETIMEDOUT;
+}
+
+int rtl839x_read_phy(u32 port, u32 page, u32 reg, u32 *val)
+{
+ u32 v;
+
+ if (port > 63 || page > 4095 || reg > 31)
+ return -ENOTSUPP;
+
+ mutex_lock(&smi_lock);
+
+ sw_w32_mask(0xffff0000, port << 16, RTL839X_PHYREG_DATA_CTRL);
+ v = reg << 5 | page << 10 | ((page == 0x1fff) ? 0x1f : 0) << 23;
+ sw_w32(v, RTL839X_PHYREG_ACCESS_CTRL);
+
+ sw_w32(0x1ff, RTL839X_PHYREG_CTRL);
+
+ v |= 1;
+ sw_w32(v, RTL839X_PHYREG_ACCESS_CTRL);
+
+ do {
+ } while (sw_r32(RTL839X_PHYREG_ACCESS_CTRL) & 0x1);
+
+ *val = sw_r32(RTL839X_PHYREG_DATA_CTRL) & 0xffff;
+
+ mutex_unlock(&smi_lock);
+ return 0;
+}
+
+static int read_phy(u32 port, u32 page, u32 reg, u32 *val)
+{
+ if (soc_info.family == RTL8390_FAMILY_ID)
+ return rtl839x_read_phy(port, page, reg, val);
+ else
+ return rtl838x_read_phy(port, page, reg, val);
+}
+
+static int write_phy(u32 port, u32 page, u32 reg, u32 val)
+{
+ if (soc_info.family == RTL8390_FAMILY_ID)
+ return rtl839x_write_phy(port, page, reg, val);
+ else
+ return rtl838x_write_phy(port, page, reg, val);
+}
+
+/*
+ * Write to an mmd register of the PHY
+ */
+int rtl838x_write_mmd_phy(u32 port, u32 addr, u32 reg, u32 val)
+{
+ u32 v;
+
+ pr_debug("MMD write: port %d, dev %d, reg %d, val %x\n", port, addr, reg, val);
+ val &= 0xffff;
+ mutex_lock(&smi_lock);
+
+ if (rtl838x_smi_wait_op(10000))
+ goto timeout;
+
+ sw_w32(1 << port, RTL838X_SMI_ACCESS_PHY_CTRL_0);
+ mdelay(10);
+
+ sw_w32_mask(0xffff0000, val << 16, RTL838X_SMI_ACCESS_PHY_CTRL_2);
+
+ sw_w32_mask(0x1f << 16, addr << 16, RTL838X_SMI_ACCESS_PHY_CTRL_3);
+ sw_w32_mask(0xffff, reg, RTL838X_SMI_ACCESS_PHY_CTRL_3);
+ /* mmd-access | write | cmd-start */
+ v = 1 << 1 | 1 << 2 | 1;
+ sw_w32(v, RTL838X_SMI_ACCESS_PHY_CTRL_1);
+
+ if (rtl838x_smi_wait_op(10000))
+ goto timeout;
+
+ mutex_unlock(&smi_lock);
+ return 0;
+
+timeout:
+ mutex_unlock(&smi_lock);
+ return -ETIMEDOUT;
+}
+
+/*
+ * Read to an mmd register of the PHY
+ */
+int rtl838x_read_mmd_phy(u32 port, u32 addr, u32 reg, u32 *val)
+{
+ u32 v;
+
+ mutex_lock(&smi_lock);
+
+ if (rtl838x_smi_wait_op(10000))
+ goto timeout;
+
+ sw_w32(1 << port, RTL838X_SMI_ACCESS_PHY_CTRL_0);
+ mdelay(10);
+
+ sw_w32_mask(0xffff0000, port << 16, RTL838X_SMI_ACCESS_PHY_CTRL_2);
+
+ v = addr << 16 | reg;
+ sw_w32(v, RTL838X_SMI_ACCESS_PHY_CTRL_3);
+
+ /* mmd-access | read | cmd-start */
+ v = 1 << 1 | 0 << 2 | 1;
+ sw_w32(v, RTL838X_SMI_ACCESS_PHY_CTRL_1);
+
+ if (rtl838x_smi_wait_op(10000))
+ goto timeout;
+
+ *val = sw_r32(RTL838X_SMI_ACCESS_PHY_CTRL_2) & 0xffff;
+
+ mutex_unlock(&smi_lock);
+ return 0;
+
+timeout:
+ mutex_unlock(&smi_lock);
+ return -ETIMEDOUT;
+}
+
+static void rtl8380_get_version(struct rtl838x_switch_priv *priv)
+{
+ u32 rw_save, info_save;
+ u32 info;
+
+ if (priv->id)
+ pr_debug("SoC ID: %4x: %s\n", priv->id, soc_info.name);
+ else
+ pr_err("Unknown chip id (%04x)\n", priv->id);
+
+ rw_save = sw_r32(RTL838X_INT_RW_CTRL);
+ sw_w32(rw_save | 0x3, RTL838X_INT_RW_CTRL);
+
+ info_save = sw_r32(RTL838X_CHIP_INFO);
+ sw_w32(info_save | 0xA0000000, RTL838X_CHIP_INFO);
+
+ info = sw_r32(RTL838X_CHIP_INFO);
+ sw_w32(info_save, RTL838X_CHIP_INFO);
+ sw_w32(rw_save, RTL838X_INT_RW_CTRL);
+
+ if ((info & 0xFFFF) == 0x6275) {
+ if (((info >> 16) & 0x1F) == 0x1)
+ priv->version = RTL8380_VERSION_A;
+ else if (((info >> 16) & 0x1F) == 0x2)
+ priv->version = RTL8380_VERSION_B;
+ else
+ priv->version = RTL8380_VERSION_B;
+ } else {
+ priv->version = '-';
+ }
+}
+
+static void rtl8390_get_version(struct rtl838x_switch_priv *priv)
+{
+ u32 info;
+
+ sw_w32_mask(0xf << 28, 0xa << 28, RTL839X_CHIP_INFO);
+ info = sw_r32(RTL839X_CHIP_INFO);
+ pr_info("Chip-Info: %x\n", info);
+ priv->version = RTL8390_VERSION_A;
+}
+
+int dsa_phy_read(struct dsa_switch *ds, int phy_addr, int phy_reg)
+{
+ u32 val;
+ u32 offset = 0;
+ struct rtl838x_switch_priv *priv = ds->priv;
+
+ if (phy_addr >= 24 && phy_addr <= 27
+ && priv->ports[24].phy == PHY_RTL838X_SDS) {
+ if (phy_addr == 26)
+ offset = 0x100;
+ val = sw_r32(MAPLE_SDS4_FIB_REG0r + offset + (phy_reg << 2)) & 0xffff;
+ return val;
+ }
+
+ read_phy(phy_addr, 0, phy_reg, &val);
+ return val;
+}
+
+int dsa_phy_write(struct dsa_switch *ds, int phy_addr, int phy_reg, u16 val)
+{
+ u32 offset = 0;
+ struct rtl838x_switch_priv *priv = ds->priv;
+
+ if (phy_addr >= 24 && phy_addr <= 27
+ && priv->ports[24].phy == PHY_RTL838X_SDS) {
+ if (phy_addr == 26)
+ offset = 0x100;
+ sw_w32(val, MAPLE_SDS4_FIB_REG0r + offset + (phy_reg << 2));
+ return 0;
+ }
+ return write_phy(phy_addr, 0, phy_reg, val);
+}
+
+static int rtl838x_mdio_read(struct mii_bus *bus, int addr, int regnum)
+{
+ int ret;
+ struct rtl838x_switch_priv *priv = bus->priv;
+
+ ret = dsa_phy_read(priv->ds, addr, regnum);
+ return ret;
+}
+
+static int rtl838x_mdio_write(struct mii_bus *bus, int addr, int regnum,
+ u16 val)
+{
+ struct rtl838x_switch_priv *priv = bus->priv;
+
+ return dsa_phy_write(priv->ds, addr, regnum, val);
+}
+
+static void rtl838x_enable_phy_polling(struct rtl838x_switch_priv *priv)
+{
+ int i;
+ u64 v = 0;
+
+ msleep(1000);
+ /* Enable all ports with a PHY, including the SFP-ports */
+ for (i = 0; i < priv->cpu_port; i++) {
+ if (priv->ports[i].phy)
+ v |= 1 << i;
+ }
+
+ pr_info("%s: %16llx\n", __func__, v);
+ priv->r->set_port_reg(v, priv->r->smi_poll_ctrl);
+
+ /* PHY update complete */
+ if (priv->family_id == RTL8390_FAMILY_ID)
+ sw_w32_mask(1 << 7, 0, RTL839X_SMI_GLB_CTRL);
+ else
+ sw_w32_mask(0, 0x8000, RTL838X_SMI_GLB_CTRL);
+}
+
+void rtl839x_print_matrix(void)
+{
+ volatile u64 *ptr = RTL838X_SW_BASE + RTL839X_PORT_ISO_CTRL(0);
+ int i;
+
+ for (i = 0; i < 52; i += 4)
+ pr_info("> %16llx %16llx %16llx %16llx\n",
+ ptr[i + 0], ptr[i + 1], ptr[i + 2], ptr[i + 3]);
+ pr_info("CPU_PORT> %16llx\n", ptr[52]);
+}
+
+void rtl838x_print_matrix(void)
+{
+ unsigned volatile int *ptr = RTL838X_SW_BASE + RTL838X_PORT_ISO_CTRL(0);
+ int i;
+
+ if (soc_info.family == RTL8390_FAMILY_ID)
+ return rtl839x_print_matrix();
+
+ for (i = 0; i < 28; i += 8)
+ pr_info("> %8x %8x %8x %8x %8x %8x %8x %8x\n",
+ ptr[i + 0], ptr[i + 1], ptr[i + 2], ptr[i + 3], ptr[i + 4], ptr[i + 5],
+ ptr[i + 6], ptr[i + 7]);
+ pr_info("CPU_PORT> %8x\n", ptr[28]);
+}
+
+static void rtl838x_init_stats(struct rtl838x_switch_priv *priv)
+{
+ mutex_lock(&priv->reg_mutex);
+
+ /* Enable statistics module: all counters plus debug.
+ * On RTL839x all counters are enabled by default
+ */
+ if (priv->family_id == RTL8380_FAMILY_ID)
+ sw_w32_mask(0, 3, RTL838X_STAT_CTRL);
+
+ /* Reset statistics counters */
+ sw_w32_mask(0, 1, priv->r->stat_rst);
+
+ mutex_unlock(&priv->reg_mutex);
+}
+
+static int rtl838x_setup(struct dsa_switch *ds)
+{
+ int i;
+ u64 port_bitmap = 0;
+ struct rtl838x_switch_priv *priv = ds->priv;
+
+ pr_info("%s called\n", __func__);
+
+ /* Disable MAC polling the PHY so that we can start configuration */
+ priv->r->set_port_reg(0, priv->r->smi_poll_ctrl);
+
+ for (i = 0; i < ds->num_ports; i++)
+ priv->ports[i].enable = false;
+ priv->ports[priv->cpu_port].enable = true;
+
+ /* Isolate ports from each other: traffic only CPU <-> port */
+ for (i = 0; i < priv->cpu_port; i++) {
+ if (priv->ports[i].phy) {
+ priv->r->set_port_iso_ctrl(1 << priv->cpu_port, i);
+ priv->r->mask_port_iso_ctrl(0, 1 << i, i);
+ port_bitmap |= 1 << i;
+ }
+ }
+ priv->r->set_port_iso_ctrl(port_bitmap, priv->cpu_port);
+
+ rtl838x_print_matrix();
+
+ rtl838x_init_stats(priv);
+
+ /* Enable MAC Polling PHY again */
+ rtl838x_enable_phy_polling(priv);
+ pr_info("Please wait until PHY is settled\n");
+ msleep(1000);
+ return 0;
+}
+
+static void rtl838x_get_strings(struct dsa_switch *ds,
+ int port, u32 stringset, u8 *data)
+{
+ int i;
+
+ if (stringset != ETH_SS_STATS)
+ return;
+
+ for (i = 0; i < ARRAY_SIZE(rtl838x_mib); i++)
+ strncpy(data + i * ETH_GSTRING_LEN, rtl838x_mib[i].name,
+ ETH_GSTRING_LEN);
+}
+
+static void rtl838x_get_ethtool_stats(struct dsa_switch *ds, int port,
+ uint64_t *data)
+{
+ struct rtl838x_switch_priv *priv = ds->priv;
+ const struct rtl838x_mib_desc *mib;
+ int i;
+ u64 high;
+
+ for (i = 0; i < ARRAY_SIZE(rtl838x_mib); i++) {
+ mib = &rtl838x_mib[i];
+
+ data[i] = sw_r32(priv->r->stat_port_std_mib(port) + 252 - mib->offset);
+ if (mib->size == 2) {
+ high = sw_r32(priv->r->stat_port_std_mib(port) + 252 - mib->offset - 4);
+ data[i] |= high << 32;
+ }
+ }
+}
+
+static int rtl838x_get_sset_count(struct dsa_switch *ds, int port, int sset)
+{
+ if (sset != ETH_SS_STATS)
+ return 0;
+
+ return ARRAY_SIZE(rtl838x_mib);
+}
+
+static enum dsa_tag_protocol
+rtl838x_get_tag_protocol(struct dsa_switch *ds, int port)
+{
+ /* The switch does not tag the frames, instead internally the header
+ * structure for each packet is tagged accordingly.
+ */
+ return DSA_TAG_PROTO_TRAILER;
+}
+
+static int rtl838x_get_l2aging(struct rtl838x_switch_priv *priv)
+{
+ int t = sw_r32(priv->r->l2_ctrl_1) & 0x7fffff;
+
+ pr_debug("RTL838X_L2_CTRL_1 %x\n", sw_r32(priv->r->l2_ctrl_1));
+
+ t = t * 128 / 625; /* Aging time in seconds. 0: L2 aging disabled */
+ pr_info("L2 AGING time: %d sec\n", t);
+ pr_info("Dynamic aging for ports: %x\n",
+ sw_r32(priv->r->l2_port_aging_out));
+ return t;
+}
+
+/*
+ * Set Switch L2 Aging time, t is time in milliseconds
+ * t = 0: aging is disabled
+ */
+static int rtl838x_set_l2aging(struct dsa_switch *ds, u32 t)
+{
+ struct rtl838x_switch_priv *priv = ds->priv;
+ /* Convert time in mseconds to internal value */
+ if (t > 0x10000000) /* Set to maximum */
+ t = 0x7fffff;
+ else
+ t = ((t * 625) / 1000 + 127) / 128;
+
+ sw_w32(t, priv->r->l2_ctrl_1);
+
+ return 0;
+}
+
+static void rtl838x_fast_age(struct dsa_switch *ds, int port)
+{
+ struct rtl838x_switch_priv *priv = ds->priv;
+ int s = priv->family_id == RTL8390_FAMILY_ID ? 2 : 0;
+
+ pr_info("FAST AGE port %d\n", port);
+ mutex_lock(&priv->reg_mutex);
+ /* RTL838X_L2_TBL_FLUSH_CTRL register bits, 839x has 1 bit larger
+ * port fields:
+ * 0-4: Replacing port
+ * 5-9: Flushed/replaced port
+ * 10-21: FVID
+ * 22: Entry types: 1: dynamic, 0: also static
+ * 23: Match flush port
+ * 24: Match FVID
+ * 25: Flush (0) or replace (1) L2 entries
+ * 26: Status of action (1: Start, 0: Done)
+ */
+ sw_w32(1 << (26 + s) | 1 << (23 + s) | port << 5, priv->r->l2_tbl_flush_ctrl);
+
+ do { } while (sw_r32(priv->r->l2_tbl_flush_ctrl) & (1 << (26 + s)));
+
+ mutex_unlock(&priv->reg_mutex);
+}
+
+/*
+ * Applies the same hash algorithm as the one used currently by the ASIC
+ */
+static u32 rtl838x_hash(struct rtl838x_switch_priv *priv, u64 seed)
+{
+ u32 h1, h2, h3, h;
+
+ if (sw_r32(priv->r->l2_ctrl_0) & 1) {
+ h1 = (seed >> 11) & 0x7ff;
+ h1 = ((h1 & 0x1f) << 6) | ((h1 >> 5) & 0x3f);
+
+ h2 = (seed >> 33) & 0x7ff;
+ h2 = ((h2 & 0x3f) << 5) | ((h2 >> 6) & 0x1f);
+
+ h3 = (seed >> 44) & 0x7ff;
+ h3 = ((h3 & 0x7f) << 4) | ((h3 >> 7) & 0xf);
+
+ h = h1 ^ h2 ^ h3 ^ ((seed >> 55) & 0x1ff);
+ h ^= ((seed >> 22) & 0x7ff) ^ (seed & 0x7ff);
+ } else {
+ h = ((seed >> 55) & 0x1ff) ^ ((seed >> 44) & 0x7ff)
+ ^ ((seed >> 33) & 0x7ff) ^ ((seed >> 22) & 0x7ff)
+ ^ ((seed >> 11) & 0x7ff) ^ (seed & 0x7ff);
+ }
+
+ return h;
+}
+
+static u64 rtl838x_hash_key(struct rtl838x_switch_priv *priv, u64 mac, u32 vid)
+{
+ return rtl838x_hash(priv, mac << 12 | vid);
+}
+
+static u64 read_l2_entry_using_hash(u32 hash, u32 position, u32 *r)
+{
+ u64 entry;
+ /* Search in SRAM, with hash and at position in hash bucket (0-3) */
+ u32 idx = (0 << 14) | (hash << 2) | position;
+
+ u32 cmd = 1 << 16 /* Execute cmd */
+ | 1 << 15 /* Read */
+ | 0 << 13 /* Table type 0b00 */
+ | (idx & 0x1fff);
+
+ sw_w32(cmd, RTL838X_TBL_ACCESS_L2_CTRL);
+ do { } while (sw_r32(RTL838X_TBL_ACCESS_L2_CTRL) & (1 << 16));
+ r[0] = sw_r32(RTL838X_TBL_ACCESS_L2_DATA(0));
+ r[1] = sw_r32(RTL838X_TBL_ACCESS_L2_DATA(1));
+ r[2] = sw_r32(RTL838X_TBL_ACCESS_L2_DATA(2));
+
+ entry = (((u64) r[1]) << 32) | (r[2] & 0xfffff000) | (r[0] & 0xfff);
+ return entry;
+}
+
+static u64 rtl838x_read_cam(int idx, u32 *r)
+{
+ u64 entry;
+ u32 cmd = 1 << 16 /* Execute cmd */
+ | 1 << 15 /* Read */
+ | 1 << 13 /* Table type 0b01 */
+ | (idx & 0x3f);
+ sw_w32(cmd, RTL838X_TBL_ACCESS_L2_CTRL);
+ do { } while (sw_r32(RTL838X_TBL_ACCESS_L2_CTRL) & (1 << 16));
+ r[0] = sw_r32(RTL838X_TBL_ACCESS_L2_DATA(0));
+ r[1] = sw_r32(RTL838X_TBL_ACCESS_L2_DATA(1));
+ r[2] = sw_r32(RTL838X_TBL_ACCESS_L2_DATA(2));
+
+ entry = (((u64) r[1]) << 32) | (r[2] & 0xfffff000) | (r[0] & 0xfff);
+ return entry;
+}
+
+static void rtl838x_write_cam(int idx, u32 *r)
+{
+ u32 cmd = 1 << 16 /* Execute cmd */
+ | 1 << 15 /* Read */
+ | 1 << 13 /* Table type 0b01 */
+ | (idx & 0x3f);
+
+ sw_w32(r[0], RTL838X_TBL_ACCESS_L2_DATA(0));
+ sw_w32(r[1], RTL838X_TBL_ACCESS_L2_DATA(1));
+ sw_w32(r[2], RTL838X_TBL_ACCESS_L2_DATA(2));
+
+ sw_w32(cmd, RTL838X_TBL_ACCESS_L2_CTRL);
+ do { } while (sw_r32(RTL838X_TBL_ACCESS_L2_CTRL) & (1 << 16));
+}
+
+static void rtl838x_write_hash(int idx, u32 *r)
+{
+ u32 cmd = 1 << 16 /* Execute cmd */
+ | 0 << 15 /* Write */
+ | 0 << 13 /* Table type 0b00 */
+ | (idx & 0x1fff);
+
+ sw_w32(0, RTL838X_TBL_ACCESS_L2_DATA(0));
+ sw_w32(0, RTL838X_TBL_ACCESS_L2_DATA(1));
+ sw_w32(0, RTL838X_TBL_ACCESS_L2_DATA(2));
+ sw_w32(cmd, RTL838X_TBL_ACCESS_L2_CTRL);
+ do { } while (sw_r32(RTL838X_TBL_ACCESS_L2_CTRL) & (1 << 16));
+}
+
+static void dump_fdb(struct rtl838x_switch_priv *priv)
+{
+ u32 r[3];
+ int i;
+ u8 mac[6];
+ u16 vid, rvid;
+
+ mutex_lock(&priv->reg_mutex);
+
+ for (i = 0; i < 8192; i++) {
+ read_l2_entry_using_hash(i >> 2, i & 0x3, r);
+ mac[0] = (r[1] >> 20);
+ mac[1] = (r[1] >> 12);
+ mac[2] = (r[1] >> 4);
+ mac[3] = (r[1] & 0xf) << 4 | (r[2] >> 28);
+ mac[4] = (r[2] >> 20);
+ mac[5] = (r[2] >> 12);
+ vid = r[0] & 0xfff;
+ rvid = r[2] & 0xfff;
+
+ if (!(r[0] >> 17)) /* Check for invalid entry */
+ continue;
+
+ pr_info("-> port %02d: %pM, vid: %d, rvid: %d\n",
+ (r[0] >> 12) & priv->port_mask, &mac[0], vid, rvid);
+ }
+
+ mutex_unlock(&priv->reg_mutex);
+}
+
+static int rtl838x_port_fdb_dump(struct dsa_switch *ds, int port,
+ dsa_fdb_dump_cb_t *cb, void *data)
+{
+ u32 r[3];
+ u8 mac[6];
+ u16 vid, rvid;
+ struct rtl838x_switch_priv *priv = ds->priv;
+ int i;
+
+ mutex_lock(&priv->reg_mutex);
+
+ for (i = 0; i < 8192; i++) {
+ read_l2_entry_using_hash(i >> 2, i & 0x3, r);
+ mac[0] = (r[1] >> 20);
+ mac[1] = (r[1] >> 12);
+ mac[2] = (r[1] >> 4);
+ mac[3] = (r[1] & 0xf) << 4 | (r[2] >> 28);
+ mac[4] = (r[2] >> 20);
+ mac[5] = (r[2] >> 12);
+ vid = r[0] & 0xfff;
+ rvid = r[2] & 0xfff;
+
+ if (!(r[0] >> 17)) /* Check for invalid entry */
+ continue;
+
+ if (port == ((r[0] >> 12) & 0x1f)) {
+ pr_info("-> mac %pM, vid: %d, rvid: %d\n", &mac[0], vid, rvid);
+ cb(mac, vid, (r[0] >> 19) & 1, data);
+ }
+ }
+
+ for (i = 0; i < 64; i++) {
+ rtl838x_read_cam(i, r);
+ mac[0] = (r[1] >> 20);
+ mac[1] = (r[1] >> 12);
+ mac[2] = (r[1] >> 4);
+ mac[3] = (r[1] & 0xf) << 4 | (r[2] >> 28);
+ mac[4] = (r[2] >> 20);
+ mac[5] = (r[2] >> 12);
+ vid = r[0] & 0xfff;
+
+ if (!(r[0] >> 17))
+ continue;
+
+ pr_info("Found in CAM: R1 %x R2 %x R3 %x\n", r[0], r[1], r[2]);
+ if (port == ((r[0] >> 12) & priv->port_mask))
+ cb(mac, vid, (r[0] >> 19) & 1, data);
+ }
+
+ mutex_unlock(&priv->reg_mutex);
+ return 0;
+}
+
+static int rtl838x_port_fdb_del(struct dsa_switch *ds, int port,
+ const unsigned char *addr, u16 vid)
+{
+ struct rtl838x_switch_priv *priv = ds->priv;
+ u64 mac = ether_addr_to_u64(addr);
+ u32 key = rtl838x_hash_key(priv, mac, vid);
+ int i;
+ u32 r[3];
+ u64 entry;
+ int idx = -1;
+ int err = 0;
+
+ pr_info("In %s, mac %llx, vid: %d, key: %x\n", __func__, mac, vid, key);
+ mutex_lock(&priv->reg_mutex);
+ for (i = 0; i < 4; i++) {
+ entry = read_l2_entry_using_hash(key, i, r);
+ if (!(r[0] >> 17)) /* Check for invalid entry */
+ continue;
+ if ((entry & 0x0fffffffffffffff) == ((mac << 12) | vid)) {
+ idx = (key << 2) | i;
+ break;
+ }
+ }
+
+ if (idx >= 0) {
+ r[0] = r[1] = r[2] = 0;
+ rtl838x_write_hash(idx, r);
+ goto out;
+ }
+
+ /* Check CAM for spillover from hash buckets */
+ for (i = 0; i < 64; i++) {
+ entry = rtl838x_read_cam(i, r);
+ if ((entry & 0x0fffffffffffffff) == ((mac << 12) | vid)) {
+ idx = i;
+ break;
+ }
+ }
+ if (idx >= 0) {
+ r[0] = r[1] = r[2] = 0;
+ rtl838x_write_cam(idx, r);
+ goto out;
+ }
+ err = -ENOENT;
+out:
+ mutex_unlock(&priv->reg_mutex);
+ return err;
+}
+
+static int rtl838x_port_fdb_add(struct dsa_switch *ds, int port,
+ const unsigned char *addr, u16 vid)
+{
+ struct rtl838x_switch_priv *priv = ds->priv;
+ u64 mac = ether_addr_to_u64(addr);
+ u32 key = rtl838x_hash_key(priv, mac, vid);
+ int i;
+ u32 r[3];
+ int idx = -1;
+ u64 entry;
+ int err = 0;
+
+ mutex_lock(&priv->reg_mutex);
+ for (i = 0; i < 4; i++) {
+ entry = read_l2_entry_using_hash(key, i, r);
+ if (!(r[0] >> 17)) { /* Check for invalid entry */
+ idx = (key << 2) | i;
+ break;
+ }
+ if ((entry & 0x0fffffffffffffff) == ((mac << 12) | vid)) {
+ idx = (key << 2) | i;
+ break;
+ }
+ }
+ if (idx >= 0) {
+ // Found for del: R1 60000 R2 901b0e9 R3 12b0e000, 901b0e912b0e000
+ r[0] = 3 << 17 | port << 12; // Aging and port
+ r[0] |= vid;
+ r[1] = mac >> 16;
+ r[2] = (mac & 0xffff) << 12; /* rvid = 0 */
+ rtl838x_write_hash(idx, r);
+ goto out;
+ }
+
+ /* Hash bucket full, try CAM */
+ for (i = 0; i < 64; i++) {
+ entry = rtl838x_read_cam(i, r);
+ if (!(r[0] >> 17)) { /* Check for invalid entry */
+ if (idx < 0) /* First empty entry? */
+ idx = i;
+ break;
+ } else if ((entry & 0x0fffffffffffffff) == ((mac << 12) | vid)) {
+ pr_debug("Found entry in CAM\n");
+ idx = i;
+ break;
+ }
+ }
+ if (idx >= 0) {
+ r[0] = 3 << 17 | port << 12; // Aging
+ r[0] |= vid;
+ r[1] = mac >> 16;
+ r[2] = (mac & 0xffff) << 12; /* rvid = 0 */
+ rtl838x_write_cam(idx, r);
+ goto out;
+ }
+ err = -ENOTSUPP;
+out:
+ mutex_unlock(&priv->reg_mutex);
+ return err;
+}
+
+static void rtl838x_port_stp_state_set(struct dsa_switch *ds, int port,
+ u8 state)
+{
+ u32 cmd, msti = 0;
+ u32 port_state[4];
+ int index, bit, i;
+
+ struct rtl838x_switch_priv *priv = ds->priv;
+ int n = priv->family_id == RTL8380_FAMILY_ID ? 2 : 4;
+
+ pr_info("%s: port %d state %2x\n", __func__, port, state);
+ if (port >= priv->cpu_port)
+ return;
+
+ mutex_lock(&priv->reg_mutex);
+
+ index = n - (port >> 4) - 1;
+ bit = (port << 1) % 32;
+
+ if (priv->family_id == RTL8380_FAMILY_ID) {
+ cmd = 1 << 15 /* Execute cmd */
+ | 1 << 14 /* Read */
+ | 2 << 12 /* Table type 0b10 */
+ | (msti & 0xfff);
+ } else {
+ cmd = 1 << 16 /* Execute cmd */
+ | 0 << 15 /* Read */
+ | 5 << 12 /* Table type 0b101 */
+ | (msti & 0xfff);
+ }
+ priv->r->exec_tbl0_cmd(cmd);
+
+ for (i = 0; i < n; i++)
+ port_state[i] = sw_r32(priv->r->tbl_access_data_0(i));
+
+ pr_debug("Current state, port %d: %d\n", port, (port_state[index] >> bit) & 3);
+ port_state[index] &= ~(3 << bit);
+
+ switch (state) {
+ case BR_STATE_DISABLED: /* 0 */
+ port_state[index] |= (0 << bit);
+ break;
+ case BR_STATE_BLOCKING: /* 4 */
+ case BR_STATE_LISTENING: /* 1 */
+ port_state[index] |= (1 << bit);
+ break;
+ case BR_STATE_LEARNING: /* 2 */
+ port_state[index] |= (2 << bit);
+ break;
+ case BR_STATE_FORWARDING: /* 3*/
+ port_state[index] |= (3 << bit);
+ default:
+ break;
+ }
+
+ if (priv->family_id == RTL8380_FAMILY_ID) {
+ cmd = 1 << 15 /* Execute cmd */
+ | 0 << 14 /* Write */
+ | 2 << 12 /* Table type 0b10 */
+ | (msti & 0xfff);
+ } else {
+ cmd = 1 << 16 /* Execute cmd */
+ | 1 << 15 /* Write */
+ | 5 << 12 /* Table type 0b101 */
+ | (msti & 0xfff);
+ }
+ for (i = 0; i < n; i++)
+ sw_w32(port_state[i], priv->r->tbl_access_data_0(i));
+ priv->r->exec_tbl0_cmd(cmd);
+
+ mutex_unlock(&priv->reg_mutex);
+}
+
+static int rtl838x_port_mirror_add(struct dsa_switch *ds, int port,
+ struct dsa_mall_mirror_tc_entry *mirror,
+ bool ingress)
+{
+ /* We support 4 mirror groups, one destination port per group */
+ int group;
+ struct rtl838x_switch_priv *priv = ds->priv;
+
+ pr_info("In %s\n", __func__);
+
+ for (group = 0; group < 4; group++) {
+ if (priv->mirror_group_ports[group] == mirror->to_local_port)
+ break;
+ }
+ if (group >= 4) {
+ for (group = 0; group < 4; group++) {
+ if (priv->mirror_group_ports[group] < 0)
+ break;
+ }
+ }
+
+ if (group >= 4)
+ return -ENOSPC;
+
+ pr_debug("Using group %d\n", group);
+ mutex_lock(&priv->reg_mutex);
+ /* Enable mirroring to port across VLANs (bit 11) */
+ sw_w32(1 << 11 | (mirror->to_local_port << 4) | 1, RTL838X_MIR_CTRL(group));
+
+ if (ingress && (sw_r32(RTL838X_MIR_SPM_CTRL(group)) & (1 << port))) {
+ mutex_unlock(&priv->reg_mutex);
+ return -EEXIST;
+ }
+ if ((!ingress) && (sw_r32(RTL838X_MIR_DPM_CTRL(group)) & (1 << port))) {
+ mutex_unlock(&priv->reg_mutex);
+ return -EEXIST;
+ }
+ if (ingress)
+ sw_w32_mask(0, 1 << port, RTL838X_MIR_SPM_CTRL(group));
+ else
+ sw_w32_mask(0, 1 << port, RTL838X_MIR_DPM_CTRL(group));
+
+ priv->mirror_group_ports[group] = mirror->to_local_port;
+ mutex_unlock(&priv->reg_mutex);
+ return 0;
+}
+
+static void rtl838x_port_mirror_del(struct dsa_switch *ds, int port,
+ struct dsa_mall_mirror_tc_entry *mirror)
+{
+ int group = 0;
+ struct rtl838x_switch_priv *priv = ds->priv;
+
+ pr_info("In %s\n", __func__);
+ for (group = 0; group < 4; group++) {
+ if (priv->mirror_group_ports[group] == mirror->to_local_port)
+ break;
+ }
+ if (group >= 4)
+ return;
+
+ mutex_lock(&priv->reg_mutex);
+ if (mirror->ingress) {
+ /* Ingress, clear source port matrix */
+ sw_w32_mask(1 << port, 0, RTL838X_MIR_SPM_CTRL(group));
+ } else {
+ /* Egress, clear destination port matrix */
+ sw_w32_mask(1 << port, 0, RTL838X_MIR_DPM_CTRL(group));
+ }
+
+ if (!(sw_r32(RTL838X_MIR_DPM_CTRL(group)) || sw_r32(RTL838X_MIR_DPM_CTRL(group)))) {
+ priv->mirror_group_ports[group] = -1;
+ sw_w32(0, RTL838X_MIR_CTRL(group));
+ }
+
+ mutex_unlock(&priv->reg_mutex);
+}
+
+
+void rtl838x_vlan_profile_dump(int index)
+{
+ u32 profile;
+
+ if (index < 0 || index > 7)
+ return;
+
+ profile = sw_r32(RTL838X_VLAN_PROFILE(index));
+
+ pr_info("VLAN %d: L2 learning: %d, L2 Unknown MultiCast Field %x",
+ index, profile & 1, (profile >> 1) & 0x1ff);
+ pr_info(" IPv4 Unkn MultiCast Field %x, IPv6 Unkn MultiCast Field: %x",
+ (profile >> 10) & 0x1ff, (profile >> 19) & 0x1ff);
+}
+
+static int rtl838x_vlan_filtering(struct dsa_switch *ds, int port,
+ bool vlan_filtering)
+{
+ struct rtl838x_switch_priv *priv = ds->priv;
+
+ pr_info("%s: port %d\n", __func__, port);
+ mutex_lock(&priv->reg_mutex);
+
+ if (vlan_filtering) {
+ /* Enable ingress and egress filtering */
+ if (port != priv->cpu_port) {
+ if (port < 16) {
+ sw_w32_mask(0b10 << (port << 1),
+ 0b01 << (port << 1),
+ RTL838X_VLAN_PORT_IGR_FLTR_0);
+ } else {
+ sw_w32_mask(0b10 << ((port - 16) << 1),
+ 0b01 << ((port - 16) << 1),
+ RTL838X_VLAN_PORT_IGR_FLTR_1);
+ }
+ }
+ sw_w32_mask(0, 1 << port, RTL838X_VLAN_PORT_EGR_FLTR);
+ } else {
+ /* Disable ingress and egress filtering */
+ if (port != priv->cpu_port) {
+ if (port < 16) {
+ sw_w32_mask(0b11 << (port << 1),
+ 0,
+ RTL838X_VLAN_PORT_IGR_FLTR_0);
+ } else {
+ sw_w32_mask(0b11 << ((port - 16) << 1),
+ 0,
+ RTL838X_VLAN_PORT_IGR_FLTR_1);
+ }
+ }
+ sw_w32_mask(1 << port, 0, RTL838X_VLAN_PORT_EGR_FLTR);
+ }
+
+ /* We need to do something to the CPU-Port, too */
+ mutex_unlock(&priv->reg_mutex);
+
+ return 0;
+}
+
+static int rtl838x_vlan_prepare(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_vlan *vlan)
+{
+ struct rtl838x_vlan_info info;
+ struct rtl838x_switch_priv *priv = ds->priv;
+
+ pr_info("%s: port %d\n", __func__, port);
+
+ mutex_lock(&priv->reg_mutex);
+
+ priv->r->vlan_tables_read(1, &info);
+
+ pr_info("Tagged ports %llx, untag %llx, prof %x, MC# %d, UC# %d, MSTI %x\n",
+ info.tagged_ports, info.untagged_ports, info.vlan_conf & 7,
+ (info.vlan_conf & 8) >> 3, (info.vlan_conf & 16) >> 4,
+ (info.vlan_conf & 0x3e0) >> 5);
+
+ mutex_unlock(&priv->reg_mutex);
+ return 0;
+}
+
+static void rtl838x_vlan_add(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_vlan *vlan)
+{
+ struct rtl838x_vlan_info info;
+ struct rtl838x_switch_priv *priv = ds->priv;
+ int v;
+ u64 portmask;
+
+ pr_info("%s port %d, vid_end %d, vid_end %d, flags %x\n", __func__,
+ port, vlan->vid_begin, vlan->vid_end, vlan->flags);
+
+ if (vlan->vid_begin > 4095 || vlan->vid_end > 4095) {
+ dev_err(priv->dev, "VLAN out of range: %d - %d",
+ vlan->vid_begin, vlan->vid_end);
+ return;
+ }
+
+ mutex_lock(&priv->reg_mutex);
+
+ if (vlan->flags & BRIDGE_VLAN_INFO_PVID) {
+ for (v = vlan->vid_begin; v <= vlan->vid_end; v++) {
+ /* Set both inner and outer PVID of the port */
+ sw_w32((v << 16) | v, RTL838X_VLAN_PORT_PB_VLAN(port));
+ }
+ }
+
+ if (vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED) {
+ for (v = vlan->vid_begin; v <= vlan->vid_end; v++) {
+ /* Get untagged port memberships of this vlan */
+ priv->r->vlan_tables_read(v, &info);
+ portmask = info.untagged_ports | (1 << port);
+ pr_debug("Untagged ports, VLAN %d: %llx\n", v, portmask);
+ priv->r->vlan_set_untagged(v, portmask);
+ }
+ } else {
+ for (v = vlan->vid_begin; v <= vlan->vid_end; v++) {
+ /* Get tagged port memberships of this vlan */
+ priv->r->vlan_tables_read(v, &info);
+ portmask = info.tagged_ports | (1 << port);
+ pr_debug("Tagged ports, VLAN %d: %llx\n", v, portmask);
+ priv->r->vlan_set_tagged(v, portmask, info.vlan_conf);
+ }
+ }
+ mutex_unlock(&priv->reg_mutex);
+}
+
+static int rtl838x_vlan_del(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_vlan *vlan)
+{
+ struct rtl838x_vlan_info info;
+ struct rtl838x_switch_priv *priv = ds->priv;
+ int v;
+ u64 portmask;
+
+ pr_info("%s: port %d, vid_end %d, vid_end %d, flags %x\n", __func__,
+ port, vlan->vid_begin, vlan->vid_end, vlan->flags);
+
+ if (vlan->vid_begin > 4095 || vlan->vid_end > 4095) {
+ dev_err(priv->dev, "VLAN out of range: %d - %d",
+ vlan->vid_begin, vlan->vid_end);
+ return -ENOTSUPP;
+ }
+
+ mutex_lock(&priv->reg_mutex);
+
+ for (v = vlan->vid_begin; v <= vlan->vid_end; v++) {
+ /* Reset both inner and out PVID of the port */
+ sw_w32(0, RTL838X_VLAN_PORT_PB_VLAN(port));
+
+ if (vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED) {
+ /* Get untagged port memberships of this vlan */
+ priv->r->vlan_tables_read(v, &info);
+ portmask = info.untagged_ports & (~(1 << port));
+ pr_info("Untagged ports, VLAN %d: %llx\n", v, portmask);
+ priv->r->vlan_set_untagged(v, portmask);
+ }
+
+ /* Get tagged port memberships of this vlan */
+ priv->r->vlan_tables_read(v, &info);
+ portmask = info.tagged_ports & (~(1 << port));
+ pr_info("Tagged ports, VLAN %d: %llx\n", v, portmask);
+ priv->r->vlan_set_tagged(v, portmask, info.vlan_conf);
+ }
+ mutex_unlock(&priv->reg_mutex);
+
+ return 0;
+}
+
+static void rtl838x_port_bridge_leave(struct dsa_switch *ds, int port,
+ struct net_device *bridge)
+{
+ struct rtl838x_switch_priv *priv = ds->priv;
+ u64 port_bitmap = 1 << priv->cpu_port;
+ int i;
+
+ pr_info("%s %x: %d", __func__, (u32)priv, port);
+ mutex_lock(&priv->reg_mutex);
+ for (i = 0; i < ds->num_ports; i++) {
+ /* Remove this port from the port matrix of the other ports
+ * in the same bridge. If the port is disabled, port matrix
+ * is kept and not being setup until the port becomes enabled.
+ * And the other port's port matrix cannot be broken when the
+ * other port is still a VLAN-aware port.
+ */
+ if (dsa_is_user_port(ds, i) && i != port) {
+ if (dsa_to_port(ds, i)->bridge_dev != bridge)
+ continue;
+ if (priv->ports[i].enable)
+ priv->r->mask_port_iso_ctrl(1 << port, 0, i);
+ priv->ports[i].pm |= 1 << port;
+
+ port_bitmap &= ~(1 << i);
+ }
+ }
+
+ /* Add all other ports to this port matrix. */
+ if (priv->ports[port].enable)
+ priv->r->mask_port_iso_ctrl(0, port_bitmap, port);
+ priv->ports[port].pm &= ~port_bitmap;
+ mutex_unlock(&priv->reg_mutex);
+
+ rtl838x_print_matrix();
+}
+
+static int rtl838x_port_bridge_join(struct dsa_switch *ds, int port,
+ struct net_device *bridge)
+{
+ struct rtl838x_switch_priv *priv = ds->priv;
+ u64 port_bitmap = 1 << priv->cpu_port;
+ int i;
+
+ pr_info("%s %x: %d %llx", __func__, (u32)priv, port, port_bitmap);
+ mutex_lock(&priv->reg_mutex);
+ for (i = 0; i < ds->num_ports; i++) {
+ /* Add this port to the port matrix of the other ports in the
+ * same bridge. If the port is disabled, port matrix is kept
+ * and not being setup until the port becomes enabled.
+ */
+ if (dsa_is_user_port(ds, i) && i != port) {
+ if (dsa_to_port(ds, i)->bridge_dev != bridge)
+ continue;
+ if (priv->ports[i].enable)
+ priv->r->mask_port_iso_ctrl(0, 1 << port, i);
+ priv->ports[i].pm |= 1 << port;
+
+ port_bitmap |= 1 << i;
+ }
+ }
+
+ /* Add all other ports to this port matrix. */
+ if (priv->ports[port].enable) {
+ priv->r->mask_port_iso_ctrl(0, 1 << port, priv->cpu_port);
+ priv->r->mask_port_iso_ctrl(0, port_bitmap, port);
+ }
+ priv->ports[port].pm |= port_bitmap;
+ mutex_unlock(&priv->reg_mutex);
+
+ return 0;
+}
+
+static int rtl838x_port_enable(struct dsa_switch *ds, int port,
+ struct phy_device *phydev)
+{
+ struct rtl838x_switch_priv *priv = ds->priv;
+
+ pr_info("%s: %x %d", __func__, (u32) priv, port);
+ priv->ports[port].enable = true;
+
+ if (dsa_is_cpu_port(ds, port))
+ return 0;
+
+ /* add port to switch mask of CPU_PORT */
+ priv->r->mask_port_iso_ctrl(0, 1 << port, priv->cpu_port);
+
+ /* add all other ports in the same bridge to switch mask of port */
+ priv->r->mask_port_iso_ctrl(0, priv->ports[port].pm, port);
+
+ /* enable PHY polling */
+ sw_w32_mask(0, 1 << port, RTL838X_SMI_POLL_CTRL);
+
+ return 0;
+}
+
+static void rtl838x_port_disable(struct dsa_switch *ds, int port)
+{
+ struct rtl838x_switch_priv *priv = ds->priv;
+
+ pr_info("%s %x: %d", __func__, (u32)priv, port);
+
+ /* you can only disable user ports */
+ if (!dsa_is_user_port(ds, port))
+ return;
+
+ /* remove port from switch mask of CPU_PORT */
+ priv->r->mask_port_iso_ctrl(1 << port, 0, priv->cpu_port);
+
+ /* remove all other ports in the same bridge from switch mask of port */
+ priv->r->mask_port_iso_ctrl(priv->ports[port].pm, 0, port);
+
+ priv->ports[port].enable = false;
+
+ /* disable PHY polling */
+ sw_w32_mask(1 << port, 0, RTL838X_SMI_POLL_CTRL);
+}
+
+static int rtl838x_get_mac_eee(struct dsa_switch *ds, int port,
+ struct ethtool_eee *e)
+{
+ struct rtl838x_switch_priv *priv = ds->priv;
+
+ pr_info("%s: port %d", __func__, port);
+ e->supported = SUPPORTED_100baseT_Full | SUPPORTED_1000baseT_Full;
+ if (sw_r32(priv->r->mac_force_mode_ctrl(port)) & (1 << 9))
+ e->advertised |= ADVERTISED_100baseT_Full;
+
+ if (sw_r32(priv->r->mac_force_mode_ctrl(port)) & (1 << 10))
+ e->advertised |= ADVERTISED_1000baseT_Full;
+
+ e->eee_enabled = priv->ports[port].eee_enabled;
+ pr_info("enabled: %d, active %x\n", e->eee_enabled, e->advertised);
+
+ if (sw_r32(RTL838X_MAC_EEE_ABLTY) & (1 << port)) {
+ e->lp_advertised = ADVERTISED_100baseT_Full;
+ e->lp_advertised |= ADVERTISED_1000baseT_Full;
+ }
+
+ e->eee_active = !!(e->advertised & e->lp_advertised);
+ pr_info("active: %d, lp %x\n", e->eee_active, e->lp_advertised);
+
+ return 0;
+}
+
+static int rtl838x_set_mac_eee(struct dsa_switch *ds, int port,
+ struct ethtool_eee *e)
+{
+ struct rtl838x_switch_priv *priv = ds->priv;
+
+ pr_info("%s: port %d", __func__, port);
+ if (e->eee_enabled) {
+ pr_info("Globally enabling EEE\n");
+ sw_w32_mask(0x4, 0, RTL838X_SMI_GLB_CTRL);
+ }
+ if (e->eee_enabled) {
+ pr_info("Enabling EEE for MAC %d\n", port);
+ sw_w32_mask(0, 3 << 9, priv->r->mac_force_mode_ctrl(port));
+ sw_w32_mask(0, 1 << port, RTL838X_EEE_PORT_TX_EN);
+ sw_w32_mask(0, 1 << port, RTL838X_EEE_PORT_RX_EN);
+ priv->ports[port].eee_enabled = true;
+ e->eee_enabled = true;
+ } else {
+ pr_info("Disabling EEE for MAC %d\n", port);
+ sw_w32_mask(3 << 9, 0, priv->r->mac_force_mode_ctrl(port));
+ sw_w32_mask(1 << port, 0, RTL838X_EEE_PORT_TX_EN);
+ sw_w32_mask(1 << port, 0, RTL838X_EEE_PORT_RX_EN);
+ priv->ports[port].eee_enabled = false;
+ e->eee_enabled = false;
+ }
+ return 0;
+}
+
+static void rtl838x_phylink_mac_config(struct dsa_switch *ds, int port,
+ unsigned int mode,
+ const struct phylink_link_state *state)
+{
+ struct rtl838x_switch_priv *priv = ds->priv;
+ u32 reg;
+
+ pr_info("%s port %d, mode %x\n", __func__, port, mode);
+
+ if (port == priv->cpu_port) {
+ /* Set Speed, duplex, flow control
+ * FORCE_EN | LINK_EN | NWAY_EN | DUP_SEL
+ * | SPD_SEL = 0b10 | FORCE_FC_EN | PHY_MASTER_SLV_MANUAL_EN
+ * | MEDIA_SEL
+ */
+ if (priv->family_id == RTL8380_FAMILY_ID) {
+ sw_w32(0x6192F, priv->r->mac_force_mode_ctrl(priv->cpu_port));
+ /* allow CRC errors on CPU-port */
+ sw_w32_mask(0, 0x8, RTL838X_MAC_PORT_CTRL(priv->cpu_port));
+ } else {
+ sw_w32_mask(0, 3, priv->r->mac_force_mode_ctrl(priv->cpu_port));
+ }
+ return;
+ }
+
+ reg = sw_r32(priv->r->mac_force_mode_ctrl(port));
+ if (mode == MLO_AN_PHY) {
+ pr_info("PHY autonegotiates\n");
+ reg |= 1 << 2;
+ sw_w32(reg, priv->r->mac_force_mode_ctrl(port));
+ return;
+ }
+
+ if (mode != MLO_AN_FIXED)
+ pr_info("Not fixed\n");
+
+ /* Clear id_mode_dis bit, and the existing port mode, let
+ * RGMII_MODE_EN bet set by mac_link_{up,down}
+ */
+ reg &= ~(RX_PAUSE_EN | TX_PAUSE_EN);
+
+ if (state->pause & MLO_PAUSE_TXRX_MASK) {
+ if (state->pause & MLO_PAUSE_TX)
+ reg |= TX_PAUSE_EN;
+ reg |= RX_PAUSE_EN;
+ }
+
+ reg &= ~(3 << 4);
+ switch (state->speed) {
+ case SPEED_1000:
+ reg |= 2 << 4;
+ break;
+ case SPEED_100:
+ reg |= 1 << 4;
+ break;
+ }
+
+ reg &= ~(DUPLEX_FULL | FORCE_LINK_EN);
+ if (state->link)
+ reg |= FORCE_LINK_EN;
+ if (state->duplex == DUPLEX_FULL)
+ reg |= DUPLX_MODE;
+
+ // Disable AN
+ reg &= ~(1 << 2);
+ sw_w32(reg, priv->r->mac_force_mode_ctrl(port));
+}
+
+static void rtl838x_phylink_mac_link_down(struct dsa_switch *ds, int port,
+ unsigned int mode,
+ phy_interface_t interface)
+{
+ /* Stop TX/RX to port */
+ sw_w32_mask(0x03, 0, RTL838X_MAC_PORT_CTRL(port));
+}
+
+static void rtl838x_phylink_mac_link_up(struct dsa_switch *ds, int port,
+ unsigned int mode,
+ phy_interface_t interface,
+ struct phy_device *phydev)
+{
+ /* Restart TX/RX to port */
+ sw_w32_mask(0, 0x03, RTL838X_MAC_PORT_CTRL(port));
+}
+
+static void rtl838x_phylink_validate(struct dsa_switch *ds, int port,
+ unsigned long *supported,
+ struct phylink_link_state *state)
+{
+ __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
+
+ pr_info("In %s port %d", __func__, port);
+
+ if (!phy_interface_mode_is_rgmii(state->interface) &&
+ state->interface != PHY_INTERFACE_MODE_1000BASEX &&
+ state->interface != PHY_INTERFACE_MODE_MII &&
+ state->interface != PHY_INTERFACE_MODE_REVMII &&
+ state->interface != PHY_INTERFACE_MODE_GMII &&
+ state->interface != PHY_INTERFACE_MODE_QSGMII &&
+ state->interface != PHY_INTERFACE_MODE_INTERNAL &&
+ state->interface != PHY_INTERFACE_MODE_SGMII) {
+ bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
+ dev_err(ds->dev,
+ "Unsupported interface: %d for port %d\n",
+ state->interface, port);
+ return;
+ }
+
+ /* switch chip-id? if (priv->id == 0x8382) */
+
+ /* Allow all the expected bits */
+ phylink_set(mask, Autoneg);
+ phylink_set_port_modes(mask);
+ phylink_set(mask, Pause);
+ phylink_set(mask, Asym_Pause);
+
+ /* With the exclusion of MII and Reverse MII, we support Gigabit,
+ * including Half duplex
+ */
+ if (state->interface != PHY_INTERFACE_MODE_MII &&
+ state->interface != PHY_INTERFACE_MODE_REVMII) {
+ phylink_set(mask, 1000baseT_Full);
+ phylink_set(mask, 1000baseT_Half);
+ }
+
+ /* On both the 8380 and 8382, ports 24-27 are SFP ports */
+ if (port >= 24 && port <= 27)
+ phylink_set(mask, 1000baseX_Full);
+
+ phylink_set(mask, 10baseT_Half);
+ phylink_set(mask, 10baseT_Full);
+ phylink_set(mask, 100baseT_Half);
+ phylink_set(mask, 100baseT_Full);
+
+ bitmap_and(supported, supported, mask,
+ __ETHTOOL_LINK_MODE_MASK_NBITS);
+ bitmap_and(state->advertising, state->advertising, mask,
+ __ETHTOOL_LINK_MODE_MASK_NBITS);
+}
+
+static int rtl838x_phylink_mac_link_state(struct dsa_switch *ds, int port,
+ struct phylink_link_state *state)
+{
+ struct rtl838x_switch_priv *priv = ds->priv;
+ u32 speed;
+
+ if (port < 0 || port > priv->cpu_port)
+ return -EINVAL;
+
+ state->link = 0;
+ if (sw_r32(RTL838X_MAC_LINK_STS) & (1 << port))
+ state->link = 1;
+ state->duplex = 0;
+ if (sw_r32(RTL838X_MAC_LINK_DUP_STS) & (1 << port))
+ state->duplex = 1;
+
+ speed = sw_r32(RTL838X_MAC_LINK_SPD_STS(port));
+ speed >>= (port % 16) << 1;
+ switch (speed & 0x3) {
+ case 0:
+ state->speed = SPEED_10;
+ break;
+ case 1:
+ state->speed = SPEED_100;
+ break;
+ case 2:
+ state->speed = SPEED_1000;
+ break;
+ case 3:
+ if (port == 24 || port == 26) /* Internal serdes */
+ state->speed = SPEED_2500;
+ else
+ state->speed = SPEED_100; /* Is in fact 500Mbit */
+ }
+
+ state->pause &= (MLO_PAUSE_RX | MLO_PAUSE_TX);
+ if (sw_r32(RTL838X_MAC_RX_PAUSE_STS) & (1 << port))
+ state->pause |= MLO_PAUSE_RX;
+ if (sw_r32(RTL838X_MAC_TX_PAUSE_STS) & (1 << port))
+ state->pause |= MLO_PAUSE_TX;
+ return 1;
+}
+
+static int rtl838x_mdio_probe(struct rtl838x_switch_priv *priv)
+{
+ struct device *dev = priv->dev;
+ struct device_node *dn, *mii_np = dev->of_node;
+ struct mii_bus *bus;
+ int ret;
+ u32 pn;
+
+ pr_info("In %s\n", __func__);
+ mii_np = of_find_compatible_node(NULL, NULL, "realtek,rtl838x-mdio");
+ if (mii_np) {
+ pr_info("Found compatible MDIO node!\n");
+ } else {
+ dev_err(priv->dev, "no %s child node found", "mdio-bus");
+ return -ENODEV;
+ }
+
+ priv->mii_bus = of_mdio_find_bus(mii_np);
+ if (!priv->mii_bus) {
+ pr_info("Deferring probe of mdio bus\n");
+ return -EPROBE_DEFER;
+ }
+ if (!of_device_is_available(mii_np))
+ ret = -ENODEV;
+
+ bus = devm_mdiobus_alloc(priv->ds->dev);
+ if (!bus)
+ return -ENOMEM;
+
+ bus->name = "rtl838x slave mii";
+ bus->read = &rtl838x_mdio_read;
+ bus->write = &rtl838x_mdio_write;
+ snprintf(bus->id, MII_BUS_ID_SIZE, "%s-%d", bus->name, dev->id);
+ bus->parent = dev;
+ priv->ds->slave_mii_bus = bus;
+ priv->ds->slave_mii_bus->priv = priv;
+
+ ret = mdiobus_register(priv->ds->slave_mii_bus);
+ if (ret && mii_np) {
+ of_node_put(dn);
+ return ret;
+ }
+
+ dn = mii_np;
+ for_each_node_by_name(dn, "ethernet-phy") {
+ if (of_property_read_u32(dn, "reg", &pn))
+ continue;
+
+ // Check for the integrated SerDes of the RTL8380M first
+ if (of_property_read_bool(dn, "phy-is-integrated")
+ && priv->id == 0x8380 && pn >= 24) {
+ pr_info("----> FÓUND A SERDES\n");
+ priv->ports[pn].phy = PHY_RTL838X_SDS;
+ continue;
+ }
+
+ if (of_property_read_bool(dn, "phy-is-integrated")
+ && !of_property_read_bool(dn, "sfp")) {
+ priv->ports[pn].phy = PHY_RTL8218B_INT;
+ continue;
+ }
+
+ if (!of_property_read_bool(dn, "phy-is-integrated")
+ && of_property_read_bool(dn, "sfp")) {
+ priv->ports[pn].phy = PHY_RTL8214FC;
+ continue;
+ }
+
+ if (!of_property_read_bool(dn, "phy-is-integrated")
+ && !of_property_read_bool(dn, "sfp")) {
+ priv->ports[pn].phy = PHY_RTL8218B_EXT;
+ continue;
+ }
+ }
+
+ /* Disable MAC polling the PHY so that we can start configuration */
+ sw_w32(0x00000000, RTL838X_SMI_POLL_CTRL);
+
+ /* Enable PHY control via SoC */
+ sw_w32_mask(0, 1 << 15, RTL838X_SMI_GLB_CTRL);
+ /* Power on fibre ports and reset them if necessary */
+ if (priv->ports[24].phy == PHY_RTL838X_SDS) {
+ pr_info("Powering on fibre ports & reset\n");
+ rtl8380_sds_power(24, 1);
+ rtl8380_sds_power(26, 1);
+ }
+
+ pr_info("%s done\n", __func__);
+ return 0;
+}
+
+static const struct dsa_switch_ops rtl838x_switch_ops = {
+ .get_tag_protocol = rtl838x_get_tag_protocol,
+ .setup = rtl838x_setup,
+ .port_vlan_filtering = rtl838x_vlan_filtering,
+ .port_vlan_prepare = rtl838x_vlan_prepare,
+ .port_vlan_add = rtl838x_vlan_add,
+ .port_vlan_del = rtl838x_vlan_del,
+ .port_bridge_join = rtl838x_port_bridge_join,
+ .port_bridge_leave = rtl838x_port_bridge_leave,
+ .port_stp_state_set = rtl838x_port_stp_state_set,
+ .set_ageing_time = rtl838x_set_l2aging,
+ .port_fast_age = rtl838x_fast_age,
+ .port_fdb_add = rtl838x_port_fdb_add,
+ .port_fdb_del = rtl838x_port_fdb_del,
+ .port_fdb_dump = rtl838x_port_fdb_dump,
+ .port_enable = rtl838x_port_enable,
+ .port_disable = rtl838x_port_disable,
+ .port_mirror_add = rtl838x_port_mirror_add,
+ .port_mirror_del = rtl838x_port_mirror_del,
+ .phy_read = dsa_phy_read,
+ .phy_write = dsa_phy_write,
+ .get_strings = rtl838x_get_strings,
+ .get_ethtool_stats = rtl838x_get_ethtool_stats,
+ .get_sset_count = rtl838x_get_sset_count,
+ .phylink_validate = rtl838x_phylink_validate,
+ .phylink_mac_link_state = rtl838x_phylink_mac_link_state,
+ .phylink_mac_config = rtl838x_phylink_mac_config,
+ .phylink_mac_link_down = rtl838x_phylink_mac_link_down,
+ .phylink_mac_link_up = rtl838x_phylink_mac_link_up,
+ .set_mac_eee = rtl838x_set_mac_eee,
+ .get_mac_eee = rtl838x_get_mac_eee,
+
+};
+
+static int __init rtl838x_sw_probe(struct platform_device *pdev)
+{
+ int err = 0, i;
+ struct rtl838x_switch_priv *priv;
+ struct device *dev = &pdev->dev;
+
+ pr_info("Probing RTL838X switch device\n");
+ if (!pdev->dev.of_node) {
+ dev_err(dev, "No DT found\n");
+ return -EINVAL;
+ }
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->ds = dsa_switch_alloc(dev, DSA_MAX_PORTS);
+
+ if (!priv->ds)
+ return -ENOMEM;
+ priv->ds->dev = dev;
+ priv->ds->priv = priv;
+ priv->ds->ops = &rtl838x_switch_ops;
+ priv->dev = dev;
+
+ priv->family_id = soc_info.family;
+ priv->id = soc_info.id;
+ if (soc_info.family == RTL8380_FAMILY_ID) {
+ priv->cpu_port = RTL838X_CPU_PORT;
+ priv->port_mask = 0x1f;
+ priv->r = &rtl838x_reg;
+ priv->ds->num_ports = 30;
+ rtl8380_get_version(priv);
+ } else {
+ priv->cpu_port = RTL839X_CPU_PORT;
+ priv->port_mask = 0x3f;
+ priv->r = &rtl839x_reg;
+ priv->ds->num_ports = 53;
+ rtl8390_get_version(priv);
+ }
+ pr_info("Chip version %c\n", priv->version);
+
+ err = rtl838x_mdio_probe(priv);
+ if (err) {
+ /* Probing fails the 1st time because of missing ethernet driver
+ * initialization. Use this to disable traffic in case the bootloader left if on
+ */
+ return err;
+ }
+ err = dsa_register_switch(priv->ds);
+ if (err) {
+ dev_err(dev, "Error registering switch: %d\n", err);
+ return err;
+ }
+
+ /* Enable link and media change interrupts. Are the SERDES masks needed? */
+ sw_w32_mask(0, 3, priv->r->isr_glb_src);
+ /* ... for all ports */
+ priv->r->set_port_reg(0xffffffffffffffff, priv->r->isr_port_link_sts_chg);
+ priv->r->set_port_reg(0xffffffffffffffff, priv->r->imr_port_link_sts_chg);
+
+ priv->link_state_irq = 20;
+ if (priv->family_id == RTL8380_FAMILY_ID) {
+ err = request_irq(priv->link_state_irq, rtl838x_switch_irq,
+ IRQF_SHARED, "rtl8838x-link-state", priv->ds);
+ } else {
+ err = request_irq(priv->link_state_irq, rtl839x_switch_irq,
+ IRQF_SHARED, "rtl8838x-link-state", priv->ds);
+ }
+ if (err) {
+ dev_err(dev, "Error setting up switch interrupt.\n");
+ /* Need to free allocated switch here */
+ }
+
+ /* Enable interrupts for switch */
+ sw_w32(0x1, priv->r->imr_glb);
+
+ rtl838x_get_l2aging(priv);
+
+ /* Clear all destination ports for mirror groups */
+ for (i = 0; i < 4; i++)
+ priv->mirror_group_ports[i] = -1;
+
+ return err;
+}
+
+static int rtl838x_sw_remove(struct platform_device *pdev)
+{
+ pr_info("Removing platform driver for rtl838x-sw\n");
+ return 0;
+}
+
+static const struct of_device_id rtl838x_switch_of_ids[] = {
+ { .compatible = "realtek,rtl838x-switch"},
+ { /* sentinel */ }
+};
+
+
+MODULE_DEVICE_TABLE(of, rtl838x_switch_of_ids);
+
+static struct platform_driver rtl838x_switch_driver = {
+ .probe = rtl838x_sw_probe,
+ .remove = rtl838x_sw_remove,
+ .driver = {
+ .name = "rtl838x-switch",
+ .pm = NULL,
+ .of_match_table = rtl838x_switch_of_ids,
+ },
+};
+
+module_platform_driver(rtl838x_switch_driver);
+
+MODULE_AUTHOR("B. Koblitz");
+MODULE_DESCRIPTION("RTL838X SoC Switch Driver");
+MODULE_LICENSE("GPL");
diff --git a/target/linux/rtl838x/files-5.4/drivers/net/ethernet/rtl838x_eth.c b/target/linux/rtl838x/files-5.4/drivers/net/ethernet/rtl838x_eth.c
new file mode 100644
index 0000000000..9634b6a24f
--- /dev/null
+++ b/target/linux/rtl838x/files-5.4/drivers/net/ethernet/rtl838x_eth.c
@@ -0,0 +1,1205 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * linux/drivers/net/ethernet/rtl838x_eth.c
+ * Copyright (C) 2020 B. Koblitz
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/etherdevice.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/platform_device.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/of.h>
+#include <linux/of_net.h>
+#include <linux/of_mdio.h>
+#include <linux/module.h>
+#include <linux/phylink.h>
+#include <net/dsa.h>
+
+#include <asm/mach-rtl838x/mach-rtl838x.h>
+#include "rtl838x_eth.h"
+
+extern struct rtl838x_soc_info soc_info;
+
+/*
+ * Maximum number of RX rings is 8, assigned by switch based on
+ * packet/port priortity (not implemented)
+ * Maximum number of TX rings is 2 (only ring 0 used)
+ * RX ringlength needs to be at least 200, otherwise CPU and Switch
+ * may gridlock.
+ */
+#define RXRINGS 2
+#define RXRINGLEN 300
+#define TXRINGS 2
+#define TXRINGLEN 160
+#define TX_EN 0x8
+#define RX_EN 0x4
+#define TX_DO 0x2
+#define WRAP 0x2
+
+#define RING_BUFFER 1600
+
+struct p_hdr {
+ uint8_t *buf;
+ uint16_t reserved;
+ uint16_t size; /* buffer size */
+ uint16_t offset;
+ uint16_t len; /* pkt len */
+ uint16_t reserved2;
+ uint16_t cpu_tag[5];
+} __packed __aligned(1);
+
+struct ring_b {
+ uint32_t rx_r[RXRINGS][RXRINGLEN];
+ uint32_t tx_r[TXRINGS][TXRINGLEN];
+ struct p_hdr rx_header[RXRINGS][RXRINGLEN];
+ struct p_hdr tx_header[TXRINGS][TXRINGLEN];
+ uint32_t c_rx[RXRINGS];
+ uint32_t c_tx[TXRINGS];
+ uint8_t rx_space[RXRINGS*RXRINGLEN*RING_BUFFER];
+ uint8_t tx_space[TXRINGLEN*RING_BUFFER];
+};
+
+struct rtl838x_eth_priv {
+ struct net_device *netdev;
+ struct platform_device *pdev;
+ void *membase;
+ spinlock_t lock;
+ struct mii_bus *mii_bus;
+ struct napi_struct napi;
+ struct phylink *phylink;
+ struct phylink_config phylink_config;
+ u16 id;
+ u16 family_id;
+ const struct rtl838x_reg *r;
+ u8 cpu_port;
+};
+
+static const struct rtl838x_reg rtl838x_reg = {
+ .mac_port_ctrl = rtl838x_mac_port_ctrl,
+ .dma_if_intr_sts = RTL838X_DMA_IF_INTR_STS,
+ .dma_if_intr_msk = RTL838X_DMA_IF_INTR_MSK,
+ .dma_if_ctrl = RTL838X_DMA_IF_CTRL,
+ .mac_force_mode_ctrl = rtl838x_mac_force_mode_ctrl,
+ .dma_rx_base = rtl838x_dma_rx_base,
+ .dma_tx_base = rtl838x_dma_tx_base,
+ .dma_if_rx_ring_size = rtl838x_dma_if_rx_ring_size,
+ .dma_if_rx_ring_cntr = rtl838x_dma_if_rx_ring_cntr,
+ .dma_if_rx_cur = rtl838x_dma_if_rx_cur,
+ .rst_glb_ctrl = RTL838X_RST_GLB_CTRL_0,
+ .get_mac_link_sts = rtl838x_get_mac_link_sts,
+ .get_mac_link_dup_sts = rtl838x_get_mac_link_dup_sts,
+ .get_mac_link_spd_sts = rtl838x_get_mac_link_spd_sts,
+ .get_mac_rx_pause_sts = rtl838x_get_mac_rx_pause_sts,
+ .get_mac_tx_pause_sts = rtl838x_get_mac_tx_pause_sts,
+ .mac = RTL838X_MAC,
+ .l2_tbl_flush_ctrl = RTL838X_L2_TBL_FLUSH_CTRL,
+};
+
+static const struct rtl838x_reg rtl839x_reg = {
+ .mac_port_ctrl = rtl839x_mac_port_ctrl,
+ .dma_if_intr_sts = RTL839X_DMA_IF_INTR_STS,
+ .dma_if_intr_msk = RTL839X_DMA_IF_INTR_MSK,
+ .dma_if_ctrl = RTL839X_DMA_IF_CTRL,
+ .mac_force_mode_ctrl = rtl839x_mac_force_mode_ctrl,
+ .dma_rx_base = rtl839x_dma_rx_base,
+ .dma_tx_base = rtl839x_dma_tx_base,
+ .dma_if_rx_ring_size = rtl839x_dma_if_rx_ring_size,
+ .dma_if_rx_ring_cntr = rtl839x_dma_if_rx_ring_cntr,
+ .dma_if_rx_cur = rtl839x_dma_if_rx_cur,
+ .rst_glb_ctrl = RTL839X_RST_GLB_CTRL,
+ .get_mac_link_sts = rtl839x_get_mac_link_sts,
+ .get_mac_link_dup_sts = rtl839x_get_mac_link_dup_sts,
+ .get_mac_link_spd_sts = rtl839x_get_mac_link_spd_sts,
+ .get_mac_rx_pause_sts = rtl839x_get_mac_rx_pause_sts,
+ .get_mac_tx_pause_sts = rtl839x_get_mac_tx_pause_sts,
+ .mac = RTL839X_MAC,
+ .l2_tbl_flush_ctrl = RTL839X_L2_TBL_FLUSH_CTRL,
+};
+
+/*
+ * Discard the RX ring-buffers, called as part of the net-ISR
+ * when the buffer runs over
+ * Caller needs to hold priv->lock
+ */
+static void rtl838x_rb_cleanup(struct rtl838x_eth_priv *priv)
+{
+ int r;
+ u32 *last;
+ struct p_hdr *h;
+ struct ring_b *ring = priv->membase;
+
+ for (r = 0; r < RXRINGS; r++) {
+ last = (u32 *)KSEG1ADDR(sw_r32(priv->r->dma_if_rx_cur(r)));
+ do {
+ if ((ring->rx_r[r][ring->c_rx[r]] & 0x1))
+ break;
+ h = &ring->rx_header[r][ring->c_rx[r]];
+ h->buf = (u8 *)CPHYSADDR(ring->rx_space
+ + r * ring->c_rx[r] * RING_BUFFER);
+ h->size = RING_BUFFER;
+ h->len = 0;
+ /* make sure the header is visible to the ASIC */
+ mb();
+
+ ring->rx_r[r][ring->c_rx[r]] = CPHYSADDR(h) | 0x1
+ | (ring->c_rx[r] == (RXRINGLEN-1) ? WRAP : 0x1);
+ ring->c_rx[r] = (ring->c_rx[r] + 1) % RXRINGLEN;
+ } while (&ring->rx_r[r][ring->c_rx[r]] != last);
+ }
+}
+
+static irqreturn_t rtl838x_net_irq(int irq, void *dev_id)
+{
+ struct net_device *dev = dev_id;
+ struct rtl838x_eth_priv *priv = netdev_priv(dev);
+ u32 status = sw_r32(priv->r->dma_if_intr_sts);
+
+ spin_lock(&priv->lock);
+ /* Ignore TX interrupt */
+ if ((status & 0xf0000)) {
+ /* Clear ISR */
+ sw_w32(0x000f0000, priv->r->dma_if_intr_sts);
+ }
+
+ /* RX interrupt */
+ if (status & 0x0ff00) {
+ /* Disable RX interrupt */
+ sw_w32_mask(0xff00, 0, priv->r->dma_if_intr_msk);
+ sw_w32(0x0000ff00, priv->r->dma_if_intr_sts);
+ napi_schedule(&priv->napi);
+ }
+
+ /* RX buffer overrun */
+ if (status & 0x000ff) {
+ sw_w32(0x000000ff, priv->r->dma_if_intr_sts);
+ rtl838x_rb_cleanup(priv);
+ }
+
+ spin_unlock(&priv->lock);
+ return IRQ_HANDLED;
+}
+
+static void rtl838x_hw_reset(struct rtl838x_eth_priv *priv)
+{
+ u32 int_saved;
+
+ pr_info("RESETTING %x, CPU_PORT %d\n", priv->family_id, priv->cpu_port);
+ /* Stop TX/RX */
+ sw_w32(0x0, priv->r->mac_port_ctrl(priv->cpu_port));
+ mdelay(500);
+
+ int_saved = sw_r32(priv->r->dma_if_intr_msk);
+ /* Reset NIC */
+ sw_w32(0x08, priv->r->rst_glb_ctrl);
+ do {
+ udelay(20);
+ } while (sw_r32(priv->r->rst_glb_ctrl) & 0x08);
+ mdelay(100);
+
+ /* Restore notification settings: on RTL838x these bits are null */
+ sw_w32_mask(7 << 20, int_saved & (7 << 20), priv->r->dma_if_intr_msk);
+
+ /* Restart TX/RX to CPU port */
+ sw_w32(0x03, priv->r->mac_port_ctrl(priv->cpu_port));
+
+ if (priv->family_id == RTL8380_FAMILY_ID) {
+ /* Set Speed, duplex, flow control
+ * FORCE_EN | LINK_EN | NWAY_EN | DUP_SEL
+ * | SPD_SEL = 0b10 | FORCE_FC_EN | PHY_MASTER_SLV_MANUAL_EN
+ * | MEDIA_SEL
+ */
+ sw_w32(0x6192F, priv->r->mac_force_mode_ctrl(priv->cpu_port));
+ /* allow CRC errors on CPU-port */
+ sw_w32_mask(0, 0x8, priv->r->mac_port_ctrl(priv->cpu_port));
+ } else {
+ /* Force CPU port link up */
+ sw_w32_mask(0, 3, priv->r->mac_force_mode_ctrl(priv->cpu_port));
+ }
+
+ /* Disable and clear interrupts */
+ sw_w32(0x00000000, priv->r->dma_if_intr_msk);
+ sw_w32(0xffffffff, priv->r->dma_if_intr_sts);
+}
+
+static void rtl838x_hw_ring_setup(struct rtl838x_eth_priv *priv)
+{
+ int i;
+ struct ring_b *ring = priv->membase;
+
+ for (i = 0; i < RXRINGS; i++)
+ sw_w32(CPHYSADDR(&ring->rx_r[i]), priv->r->dma_rx_base(i));
+
+ for (i = 0; i < TXRINGS; i++)
+ sw_w32(CPHYSADDR(&ring->tx_r[i]), priv->r->dma_tx_base(i));
+}
+
+static void rtl838x_hw_en_rxtx(struct rtl838x_eth_priv *priv)
+{
+ u32 v;
+
+ pr_info("%s\n", __func__);
+ /* Disable Head of Line features for all RX rings */
+ sw_w32(0xffffffff, priv->r->dma_if_rx_ring_size(0));
+
+ /* Truncate RX buffer to 0x640 (1600) bytes, pad TX */
+ sw_w32(0x06400020, priv->r->dma_if_ctrl);
+
+ /* Enable RX done, RX overflow and TX done interrupts */
+ sw_w32(0xfffff, priv->r->dma_if_intr_msk);
+
+ /* Enable traffic, engine expects empty FCS field */
+ sw_w32_mask(0, RX_EN | TX_EN, priv->r->dma_if_ctrl);
+
+ /* Make sure to flood all traffic to CPU_PORT */
+ if (priv->family_id == RTL8390_FAMILY_ID) {
+ /* CPU port joins Lookup Miss Flooding Portmask */
+ /* Table access: CMD: read, table = 2 */
+ /* Sets MC_PMSK table port bit for port 52 to 1 */
+ sw_w32(0x28000, RTL839X_TBL_ACCESS_L2_CTRL);
+ do { } while (sw_r32(RTL839X_TBL_ACCESS_L2_CTRL) & (1 << 17));
+ v = sw_r32(RTL839X_TBL_ACCESS_L2_DATA(0));
+ sw_w32(v | 0x80000000, RTL839X_TBL_ACCESS_L2_DATA(0));
+ sw_w32(0x38000, RTL839X_TBL_ACCESS_L2_CTRL);
+ do { } while (sw_r32(RTL839X_TBL_ACCESS_L2_CTRL) & (1 << 17));
+ }
+}
+
+static void rtl838x_setup_ring_buffer(struct ring_b *ring)
+{
+ int i, j;
+
+ struct p_hdr *h;
+
+ for (i = 0; i < RXRINGS; i++) {
+ for (j = 0; j < RXRINGLEN; j++) {
+ h = &ring->rx_header[i][j];
+ h->buf = (u8 *)CPHYSADDR(ring->rx_space + i * j * RING_BUFFER);
+ h->reserved = 0;
+ h->size = RING_BUFFER;
+ h->offset = 0;
+ h->len = 0;
+ /* All rings owned by switch, last one wraps */
+ ring->rx_r[i][j] = CPHYSADDR(h) | 1 | (j == (RXRINGLEN - 1) ? WRAP : 0);
+ }
+ ring->c_rx[i] = 0;
+ }
+
+ for (i = 0; i < TXRINGS; i++) {
+ for (j = 0; j < TXRINGLEN; j++) {
+ h = &ring->tx_header[i][j];
+ h->buf = (u8 *)CPHYSADDR(ring->tx_space + i * j * RING_BUFFER);
+ h->reserved = 0;
+ h->size = RING_BUFFER;
+ h->offset = 0;
+ h->len = 0;
+ ring->tx_r[i][j] = CPHYSADDR(&ring->tx_header[i][j]);
+ }
+ /* Last header is wrapping around */
+ ring->tx_r[i][j-1] |= 2;
+ ring->c_tx[i] = 0;
+ }
+}
+
+static int rtl838x_eth_open(struct net_device *ndev)
+{
+ unsigned long flags;
+ struct rtl838x_eth_priv *priv = netdev_priv(ndev);
+ struct ring_b *ring = priv->membase;
+ int err;
+
+ pr_info("%s called %x, ring %x\n", __func__, (uint32_t)priv, (uint32_t)ring);
+ spin_lock_irqsave(&priv->lock, flags);
+ rtl838x_hw_reset(priv);
+ rtl838x_setup_ring_buffer(ring);
+ rtl838x_hw_ring_setup(priv);
+ err = request_irq(ndev->irq, rtl838x_net_irq, IRQF_SHARED,
+ ndev->name, ndev);
+ if (err) {
+ netdev_err(ndev, "%s: could not acquire interrupt: %d\n",
+ __func__, err);
+ return err;
+ }
+ phylink_start(priv->phylink);
+
+ napi_enable(&priv->napi);
+ netif_start_queue(ndev);
+
+ rtl838x_hw_en_rxtx(priv);
+
+ spin_unlock_irqrestore(&priv->lock, flags);
+
+ return 0;
+}
+
+static void rtl838x_hw_stop(struct rtl838x_eth_priv *priv)
+{
+ int i;
+
+ /* Block all ports */
+ if (priv->family_id == RTL8380_FAMILY_ID) {
+ sw_w32(0x03000000, RTL838X_TBL_ACCESS_DATA_0(0));
+ sw_w32(0x00000000, RTL838X_TBL_ACCESS_DATA_0(1));
+ sw_w32(1 << 15 | 2 << 12, RTL838X_TBL_ACCESS_CTRL_0);
+ }
+
+ /* Flush L2 address cache */
+ if (priv->family_id == RTL8380_FAMILY_ID) {
+ for (i = 0; i <= priv->cpu_port; i++) {
+ sw_w32(1 << 26 | 1 << 23 | i << 5, priv->r->l2_tbl_flush_ctrl);
+ do { } while (sw_r32(priv->r->l2_tbl_flush_ctrl) & (1 << 26));
+ }
+ } else {
+ for (i = 0; i <= priv->cpu_port; i++) {
+ sw_w32(1 << 28 | 1 << 25 | i << 5, priv->r->l2_tbl_flush_ctrl);
+ do { } while (sw_r32(priv->r->l2_tbl_flush_ctrl) & (1 << 28));
+ }
+ }
+
+ /* CPU-Port: Link down BUG: Works only for RTL838x */
+ sw_w32(0x6192D, priv->r->mac_force_mode_ctrl(priv->cpu_port));
+ mdelay(100);
+
+ /* Disable traffic */
+ sw_w32_mask(RX_EN | TX_EN, 0, priv->r->dma_if_ctrl);
+ mdelay(200);
+
+ /* Disable all TX/RX interrupts */
+ sw_w32(0x00000000, priv->r->dma_if_intr_msk);
+ sw_w32(0x000fffff, priv->r->dma_if_intr_sts);
+ sw_w32(0x00000000, priv->r->dma_if_ctrl);
+ mdelay(200);
+}
+
+static int rtl838x_eth_stop(struct net_device *ndev)
+{
+ unsigned long flags;
+ struct rtl838x_eth_priv *priv = netdev_priv(ndev);
+
+ pr_info("in %s\n", __func__);
+
+ spin_lock_irqsave(&priv->lock, flags);
+ phylink_stop(priv->phylink);
+ rtl838x_hw_stop(priv);
+ free_irq(ndev->irq, ndev);
+ napi_disable(&priv->napi);
+ netif_stop_queue(ndev);
+ spin_unlock_irqrestore(&priv->lock, flags);
+ return 0;
+}
+
+static void rtl838x_eth_set_multicast_list(struct net_device *dev)
+{
+
+}
+
+static void rtl838x_eth_tx_timeout(struct net_device *ndev)
+{
+ unsigned long flags;
+ struct rtl838x_eth_priv *priv = netdev_priv(ndev);
+
+ pr_info("in %s\n", __func__);
+ spin_lock_irqsave(&priv->lock, flags);
+ rtl838x_hw_stop(priv);
+ rtl838x_hw_ring_setup(priv);
+ rtl838x_hw_en_rxtx(priv);
+ netif_trans_update(ndev);
+ netif_start_queue(ndev);
+ spin_unlock_irqrestore(&priv->lock, flags);
+}
+
+static int rtl838x_eth_tx(struct sk_buff *skb, struct net_device *dev)
+{
+ int len, i;
+ struct rtl838x_eth_priv *priv = netdev_priv(dev);
+ struct ring_b *ring = priv->membase;
+ uint32_t val;
+ int ret;
+ unsigned long flags;
+ struct p_hdr *h;
+ int dest_port = -1;
+
+ spin_lock_irqsave(&priv->lock, flags);
+ len = skb->len;
+
+ /* Check for DSA tagging at the end of the buffer */
+ if (netdev_uses_dsa(dev) && skb->data[len-4] == 0x80 && skb->data[len-3] > 0
+ && skb->data[len-3] < 28 && skb->data[len-2] == 0x10
+ && skb->data[len-1] == 0x00) {
+ /* Reuse tag space for CRC */
+ dest_port = skb->data[len-3];
+ len -= 4;
+ }
+ if (len < ETH_ZLEN)
+ len = ETH_ZLEN;
+
+ /* ASIC expects that packet includes CRC, so we extend by 4 bytes */
+ len += 4;
+
+ if (skb_padto(skb, len)) {
+ ret = NETDEV_TX_OK;
+ goto txdone;
+ }
+
+ /* We can send this packet if CPU owns the descriptor */
+ if (!(ring->tx_r[0][ring->c_tx[0]] & 0x1)) {
+ /* Set descriptor for tx */
+ h = &ring->tx_header[0][ring->c_tx[0]];
+
+ h->buf = (u8 *)CPHYSADDR(ring->tx_space);
+ h->size = len;
+ h->len = len;
+
+ /* Create cpu_tag */
+ if (dest_port > 0) {
+ h->cpu_tag[0] = 0x0400;
+ h->cpu_tag[1] = 0x0200;
+ h->cpu_tag[2] = 0x0000;
+ h->cpu_tag[3] = (1 << dest_port) >> 16;
+ h->cpu_tag[4] = (1 << dest_port) & 0xffff;
+ } else {
+ h->cpu_tag[0] = 0;
+ h->cpu_tag[1] = 0;
+ h->cpu_tag[2] = 0;
+ h->cpu_tag[3] = 0;
+ h->cpu_tag[4] = 0;
+ }
+
+ /* Copy packet data to tx buffer */
+ memcpy((void *)KSEG1ADDR(h->buf), skb->data, len);
+ /* Make sure packet data is visible to ASIC */
+ mb();
+
+ /* Hand over to switch */
+ ring->tx_r[0][ring->c_tx[0]] = ring->tx_r[0][ring->c_tx[0]] | 0x1;
+
+ /* BUG: before tx fetch, need to make sure right data is accessed */
+ for (i = 0; i < 10; i++) {
+ val = sw_r32(priv->r->dma_if_ctrl);
+ if ((val & 0xc) == 0xc)
+ break;
+ }
+
+ /* Tell switch to send data */
+ sw_w32_mask(0, TX_DO, priv->r->dma_if_ctrl);
+
+ dev->stats.tx_packets++;
+ dev->stats.tx_bytes += len;
+ dev_kfree_skb(skb);
+ ring->c_tx[0] = (ring->c_tx[0] + 1) % TXRINGLEN;
+ ret = NETDEV_TX_OK;
+ } else {
+ dev_warn(&priv->pdev->dev, "Data is owned by switch\n");
+ ret = NETDEV_TX_BUSY;
+ }
+txdone:
+ spin_unlock_irqrestore(&priv->lock, flags);
+ return ret;
+}
+
+static int rtl838x_hw_receive(struct net_device *dev, int r, int budget)
+{
+ struct rtl838x_eth_priv *priv = netdev_priv(dev);
+ struct ring_b *ring = priv->membase;
+ struct sk_buff *skb;
+ unsigned long flags;
+ int i, len, work_done = 0;
+ u8 *data, *skb_data;
+ unsigned int val;
+ u32 *last;
+ struct p_hdr *h;
+ bool dsa = netdev_uses_dsa(dev);
+
+ spin_lock_irqsave(&priv->lock, flags);
+ last = (u32 *)KSEG1ADDR(sw_r32(priv->r->dma_if_rx_cur(r)));
+
+ if (&ring->rx_r[r][ring->c_rx[r]] == last) {
+ spin_unlock_irqrestore(&priv->lock, flags);
+ return 0;
+ }
+ do {
+ if ((ring->rx_r[r][ring->c_rx[r]] & 0x1)) {
+ netdev_warn(dev, "WARNING Ring contention: ring %x, last %x, current %x, cPTR %x, ISR %x\n", r, (uint32_t)last,
+ (u32) &ring->rx_r[r][ring->c_rx[r]],
+ ring->rx_r[r][ring->c_rx[r]],
+ sw_r32(priv->r->dma_if_intr_sts));
+ break;
+ }
+
+ h = &ring->rx_header[r][ring->c_rx[r]];
+ data = (u8 *)KSEG1ADDR(h->buf);
+ len = h->len;
+
+ if (!len)
+ break;
+ h->buf = (u8 *)CPHYSADDR(ring->rx_space
+ + r * ring->c_rx[r] * RING_BUFFER);
+ h->size = RING_BUFFER;
+ h->len = 0;
+ work_done++;
+
+ len -= 4; /* strip the CRC */
+ /* Add 4 bytes for cpu_tag */
+ if (dsa)
+ len += 4;
+
+ skb = alloc_skb(len + 4, GFP_KERNEL);
+ skb_reserve(skb, NET_IP_ALIGN);
+
+ if (likely(skb)) {
+ /* BUG: Prevent ASIC bug */
+ sw_w32(0xffffffff, priv->r->dma_if_rx_ring_size(0));
+ for (i = 0; i < RXRINGS; i++) {
+ /* Update each ring cnt */
+ val = sw_r32(priv->r->dma_if_rx_ring_cntr(i));
+ sw_w32(val, priv->r->dma_if_rx_ring_cntr(i));
+ }
+
+ skb_data = skb_put(skb, len);
+ /* Make sure data is visible */
+ mb();
+ memcpy(skb->data, (u8 *)KSEG1ADDR(data), len);
+ /* Overwrite CRC with cpu_tag */
+ if (dsa) {
+ skb->data[len-4] = 0x80;
+ skb->data[len-3] = h->cpu_tag[0] & 0x1f;
+ skb->data[len-2] = 0x10;
+ skb->data[len-1] = 0x00;
+ }
+
+ skb->protocol = eth_type_trans(skb, dev);
+ dev->stats.rx_packets++;
+ dev->stats.rx_bytes += len;
+
+ netif_receive_skb(skb);
+ } else {
+ if (net_ratelimit())
+ dev_warn(&dev->dev, "low on memory - packet dropped\n");
+ dev->stats.rx_dropped++;
+ }
+ ring->rx_r[r][ring->c_rx[r]]
+ = CPHYSADDR(h) | 0x1 | (ring->c_rx[r] == (RXRINGLEN-1) ? WRAP : 0x1);
+ ring->c_rx[r] = (ring->c_rx[r] + 1) % RXRINGLEN;
+ } while (&ring->rx_r[r][ring->c_rx[r]] != last && work_done < budget);
+
+ spin_unlock_irqrestore(&priv->lock, flags);
+ return work_done;
+}
+
+static int rtl838x_poll_rx(struct napi_struct *napi, int budget)
+{
+ struct rtl838x_eth_priv *priv = container_of(napi, struct rtl838x_eth_priv, napi);
+ int work_done = 0, r = 0;
+
+ while (work_done < budget && r < RXRINGS) {
+ work_done += rtl838x_hw_receive(priv->netdev, r, budget - work_done);
+ r++;
+ }
+
+ if (work_done < budget) {
+ napi_complete_done(napi, work_done);
+ /* Enable RX interrupt */
+ sw_w32(0xfffff, priv->r->dma_if_intr_msk);
+ }
+ return work_done;
+}
+
+
+static void rtl838x_validate(struct phylink_config *config,
+ unsigned long *supported,
+ struct phylink_link_state *state)
+{
+ __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
+
+ pr_info("In %s\n", __func__);
+
+ if (!phy_interface_mode_is_rgmii(state->interface) &&
+ state->interface != PHY_INTERFACE_MODE_1000BASEX &&
+ state->interface != PHY_INTERFACE_MODE_MII &&
+ state->interface != PHY_INTERFACE_MODE_REVMII &&
+ state->interface != PHY_INTERFACE_MODE_GMII &&
+ state->interface != PHY_INTERFACE_MODE_QSGMII &&
+ state->interface != PHY_INTERFACE_MODE_INTERNAL &&
+ state->interface != PHY_INTERFACE_MODE_SGMII) {
+ bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
+ pr_err("Unsupported interface: %d\n", state->interface);
+ return;
+ }
+
+ /* Allow all the expected bits */
+ phylink_set(mask, Autoneg);
+ phylink_set_port_modes(mask);
+ phylink_set(mask, Pause);
+ phylink_set(mask, Asym_Pause);
+
+ /* With the exclusion of MII and Reverse MII, we support Gigabit,
+ * including Half duplex
+ */
+ if (state->interface != PHY_INTERFACE_MODE_MII &&
+ state->interface != PHY_INTERFACE_MODE_REVMII) {
+ phylink_set(mask, 1000baseT_Full);
+ phylink_set(mask, 1000baseT_Half);
+ }
+
+ phylink_set(mask, 10baseT_Half);
+ phylink_set(mask, 10baseT_Full);
+ phylink_set(mask, 100baseT_Half);
+ phylink_set(mask, 100baseT_Full);
+
+ bitmap_and(supported, supported, mask,
+ __ETHTOOL_LINK_MODE_MASK_NBITS);
+ bitmap_and(state->advertising, state->advertising, mask,
+ __ETHTOOL_LINK_MODE_MASK_NBITS);
+}
+
+
+static void rtl838x_mac_config(struct phylink_config *config,
+ unsigned int mode,
+ const struct phylink_link_state *state)
+{
+ /* This is only being called for the master device,
+ * i.e. the CPU-Port
+ */
+
+ pr_info("In %s, mode %x\n", __func__, mode);
+}
+
+static void rtl838x_mac_an_restart(struct phylink_config *config)
+{
+ struct net_device *dev = container_of(config->dev, struct net_device, dev);
+ struct rtl838x_eth_priv *priv = netdev_priv(dev);
+
+ pr_info("In %s\n", __func__);
+ /* Restart by disabling and re-enabling link */
+ sw_w32(0x6192D, priv->r->mac_force_mode_ctrl(priv->cpu_port));
+ mdelay(20);
+ sw_w32(0x6192F, priv->r->mac_force_mode_ctrl(priv->cpu_port));
+}
+
+static int rtl838x_mac_pcs_get_state(struct phylink_config *config,
+ struct phylink_link_state *state)
+{
+ u32 speed;
+ struct net_device *dev = container_of(config->dev, struct net_device, dev);
+ struct rtl838x_eth_priv *priv = netdev_priv(dev);
+ int port = priv->cpu_port;
+
+ pr_info("In %s\n", __func__);
+
+ state->link = priv->r->get_mac_link_sts(port) ? 1 : 0;
+ state->duplex = priv->r->get_mac_link_dup_sts(port) ? 1 : 0;
+
+ speed = priv->r->get_mac_link_spd_sts(port);
+ switch (speed) {
+ case 0:
+ state->speed = SPEED_10;
+ break;
+ case 1:
+ state->speed = SPEED_100;
+ break;
+ state->speed = SPEED_1000;
+ break;
+ default:
+ state->speed = SPEED_UNKNOWN;
+ break;
+ }
+
+ state->pause &= (MLO_PAUSE_RX | MLO_PAUSE_TX);
+ if (priv->r->get_mac_rx_pause_sts(port))
+ state->pause |= MLO_PAUSE_RX;
+ if (priv->r->get_mac_tx_pause_sts(port))
+ state->pause |= MLO_PAUSE_TX;
+
+ return 1;
+}
+
+static void dump_mac_conf(struct rtl838x_eth_priv *priv)
+{
+ int p;
+
+ for (p = 8; p < 16; p++) {
+ pr_debug("%d: %x, force %x\n", p, sw_r32(priv->r->mac_port_ctrl(p)),
+ sw_r32(priv->r->mac_force_mode_ctrl(p))
+ );
+ }
+ pr_debug("CPU: %x, force %x\n", sw_r32(priv->r->mac_port_ctrl(priv->cpu_port)),
+ sw_r32(priv->r->mac_force_mode_ctrl(priv->cpu_port))
+ );
+}
+
+static void rtl838x_mac_link_down(struct phylink_config *config,
+ unsigned int mode,
+ phy_interface_t interface)
+{
+ struct net_device *dev = container_of(config->dev, struct net_device, dev);
+ struct rtl838x_eth_priv *priv = netdev_priv(dev);
+
+ pr_info("In %s\n", __func__);
+ /* Stop TX/RX to port */
+ sw_w32_mask(0x03, 0, priv->r->mac_port_ctrl(priv->cpu_port));
+}
+
+static void rtl838x_mac_link_up(struct phylink_config *config, unsigned int mode,
+ phy_interface_t interface,
+ struct phy_device *phy)
+{
+ struct net_device *dev = container_of(config->dev, struct net_device, dev);
+ struct rtl838x_eth_priv *priv = netdev_priv(dev);
+
+ pr_info("In %s\n", __func__);
+ /* Restart TX/RX to port */
+ sw_w32_mask(0, 0x03, priv->r->mac_port_ctrl(priv->cpu_port));
+}
+
+static void rtl838x_set_mac_hw(struct net_device *dev, u8 *mac)
+{
+ struct rtl838x_eth_priv *priv = netdev_priv(dev);
+ unsigned long flags;
+
+ spin_lock_irqsave(&priv->lock, flags);
+ pr_info("In %s\n", __func__);
+ sw_w32((mac[0] << 8) | mac[1], priv->r->mac);
+ sw_w32((mac[2] << 24) | (mac[3] << 16) | (mac[4] << 8) | mac[5], priv->r->mac + 4);
+
+ if (priv->family_id == RTL8380_FAMILY_ID) {
+ /* 2 more registers, ALE/MAC block */
+ sw_w32((mac[0] << 8) | mac[1], RTL838X_MAC_ALE);
+ sw_w32((mac[2] << 24) | (mac[3] << 16) | (mac[4] << 8) | mac[5],
+ (RTL838X_MAC_ALE + 4));
+
+ sw_w32((mac[0] << 8) | mac[1], RTL838X_MAC2);
+ sw_w32((mac[2] << 24) | (mac[3] << 16) | (mac[4] << 8) | mac[5],
+ RTL838X_MAC2 + 4);
+ }
+ spin_unlock_irqrestore(&priv->lock, flags);
+}
+
+static int rtl838x_set_mac_address(struct net_device *dev, void *p)
+{
+ struct rtl838x_eth_priv *priv = netdev_priv(dev);
+ const struct sockaddr *addr = p;
+ u8 *mac = (u8 *) (addr->sa_data);
+
+ if (!is_valid_ether_addr(addr->sa_data))
+ return -EADDRNOTAVAIL;
+
+ memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN);
+ rtl838x_set_mac_hw(dev, mac);
+
+ pr_info("Using MAC %08x%08x\n", sw_r32(priv->r->mac), sw_r32(priv->r->mac + 4));
+ return 0;
+}
+
+static int rtl8390_init_mac(struct rtl838x_eth_priv *priv)
+{
+ pr_info("Configuring RTL8390 MAC\n");
+ // from mac_config_init
+ sw_w32(0x80, RTL839X_MAC_EFUSE_CTRL);
+ sw_w32(0x4, RTL839X_RST_GLB_CTRL);
+ sw_w32(0x3c324f40, RTL839X_MAC_GLB_CTRL);
+ /* Unlimited egress rate */
+ sw_w32(0x1297b961, RTL839X_SCHED_LB_TICK_TKN_CTRL);
+
+ return 0;
+}
+
+static int rtl8380_init_mac(struct rtl838x_eth_priv *priv)
+{
+ int i;
+
+ if (priv->family_id == 0x8390)
+ return rtl8390_init_mac(priv);
+
+ if (priv->family_id != 0x8380)
+ return 0;
+
+ pr_info("%s\n", __func__);
+ /* fix timer for EEE */
+ sw_w32(0x5001411, RTL838X_EEE_TX_TIMER_GIGA_CTRL);
+ sw_w32(0x5001417, RTL838X_EEE_TX_TIMER_GELITE_CTRL);
+
+ /* Init VLAN */
+ if (priv->id == 0x8382) {
+ for (i = 0; i <= 28; i++)
+ sw_w32(0, 0xd57c + i * 0x80);
+ }
+ if (priv->id == 0x8380) {
+ for (i = 8; i <= 28; i++)
+ sw_w32(0, 0xd57c + i * 0x80);
+ }
+ return 0;
+}
+
+static int rtl838x_get_link_ksettings(struct net_device *ndev,
+ struct ethtool_link_ksettings *cmd)
+{
+ struct rtl838x_eth_priv *priv = netdev_priv(ndev);
+
+ pr_info("%s called\n", __func__);
+ return phylink_ethtool_ksettings_get(priv->phylink, cmd);
+}
+
+static int rtl838x_set_link_ksettings(struct net_device *ndev,
+ const struct ethtool_link_ksettings *cmd)
+{
+ struct rtl838x_eth_priv *priv = netdev_priv(ndev);
+
+ pr_info("%s called\n", __func__);
+ return phylink_ethtool_ksettings_set(priv->phylink, cmd);
+}
+
+
+static int rtl838x_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+ u32 val;
+ u32 offset = 0;
+ int err;
+ struct rtl838x_eth_priv *priv = bus->priv;
+
+ if (mii_id >= 24 && mii_id <= 27 && priv->id == 0x8380) {
+ if (mii_id == 26)
+ offset = 0x100;
+ val = sw_r32(MAPLE_SDS4_FIB_REG0r + offset + (regnum << 2)) & 0xffff;
+ return val;
+ }
+ err = rtl838x_read_phy(mii_id, 0, regnum, &val);
+ if (err)
+ return err;
+ return val;
+}
+
+static int rtl839x_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+ u32 val;
+ int err;
+
+ err = rtl839x_read_phy(mii_id, 0, regnum, &val);
+ if (err)
+ return err;
+ return val;
+}
+
+static int rtl838x_mdio_write(struct mii_bus *bus, int mii_id,
+ int regnum, u16 value)
+{
+ u32 offset = 0;
+ struct rtl838x_eth_priv *priv = bus->priv;
+
+ if (mii_id >= 24 && mii_id <= 27 && priv->id == 0x8380) {
+ if (mii_id == 26)
+ offset = 0x100;
+ sw_w32(value, MAPLE_SDS4_FIB_REG0r + offset + (regnum << 2));
+ return 0;
+ }
+ return rtl838x_write_phy(mii_id, 0, regnum, value);
+}
+
+static int rtl839x_mdio_write(struct mii_bus *bus, int mii_id,
+ int regnum, u16 value)
+{
+ return rtl839x_write_phy(mii_id, 0, regnum, value);
+}
+
+static int rtl838x_mdio_reset(struct mii_bus *bus)
+{
+ pr_info("%s called\n", __func__);
+ /* Disable MAC polling the PHY so that we can start configuration */
+ sw_w32(0x00000000, RTL838X_SMI_POLL_CTRL);
+
+ /* Enable PHY control via SoC */
+ sw_w32_mask(0, 1 << 15, RTL838X_SMI_GLB_CTRL);
+
+ return 0;
+}
+
+static int rtl839x_mdio_reset(struct mii_bus *bus)
+{
+ pr_info("%s called\n", __func__);
+ /* Disable MAC polling the PHY so that we can start configuration */
+ sw_w32(0x00000000, RTL839X_SMI_PORT_POLLING_CTRL);
+ sw_w32(0x00000000, RTL839X_SMI_PORT_POLLING_CTRL + 4);
+ /* Disable PHY polling via SoC */
+ sw_w32_mask(1 << 7, 0, RTL839X_SMI_GLB_CTRL);
+
+ return 0;
+}
+
+
+static int rtl838x_mdio_init(struct rtl838x_eth_priv *priv)
+{
+ struct device_node *mii_np;
+ int ret;
+
+ pr_info("%s called\n", __func__);
+ mii_np = of_get_child_by_name(priv->pdev->dev.of_node, "mdio-bus");
+
+ if (!mii_np) {
+ dev_err(&priv->pdev->dev, "no %s child node found", "mdio-bus");
+ return -ENODEV;
+ }
+
+ if (!of_device_is_available(mii_np)) {
+ ret = -ENODEV;
+ goto err_put_node;
+ }
+
+ priv->mii_bus = devm_mdiobus_alloc(&priv->pdev->dev);
+ if (!priv->mii_bus) {
+ ret = -ENOMEM;
+ goto err_put_node;
+ }
+
+ if (priv->family_id == RTL8380_FAMILY_ID) {
+ priv->mii_bus->name = "rtl838x-eth-mdio";
+ priv->mii_bus->read = rtl838x_mdio_read;
+ priv->mii_bus->write = rtl838x_mdio_write;
+ priv->mii_bus->reset = rtl838x_mdio_reset;
+ } else {
+ priv->mii_bus->name = "rtl839x-eth-mdio";
+ priv->mii_bus->read = rtl839x_mdio_read;
+ priv->mii_bus->write = rtl839x_mdio_write;
+ priv->mii_bus->reset = rtl839x_mdio_reset;
+ }
+ priv->mii_bus->priv = priv;
+ priv->mii_bus->parent = &priv->pdev->dev;
+
+ snprintf(priv->mii_bus->id, MII_BUS_ID_SIZE, "%pOFn", mii_np);
+ ret = of_mdiobus_register(priv->mii_bus, mii_np);
+
+err_put_node:
+ of_node_put(mii_np);
+ return ret;
+}
+
+static int rtl838x_mdio_remove(struct rtl838x_eth_priv *priv)
+{
+ pr_info("%s called\n", __func__);
+ if (!priv->mii_bus)
+ return 0;
+
+ mdiobus_unregister(priv->mii_bus);
+ mdiobus_free(priv->mii_bus);
+
+ return 0;
+}
+
+static const struct net_device_ops rtl838x_eth_netdev_ops = {
+ .ndo_open = rtl838x_eth_open,
+ .ndo_stop = rtl838x_eth_stop,
+ .ndo_start_xmit = rtl838x_eth_tx,
+ .ndo_set_mac_address = rtl838x_set_mac_address,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_set_rx_mode = rtl838x_eth_set_multicast_list,
+ .ndo_tx_timeout = rtl838x_eth_tx_timeout,
+};
+
+static const struct phylink_mac_ops rtl838x_phylink_ops = {
+ .validate = rtl838x_validate,
+ .mac_link_state = rtl838x_mac_pcs_get_state,
+ .mac_an_restart = rtl838x_mac_an_restart,
+ .mac_config = rtl838x_mac_config,
+ .mac_link_down = rtl838x_mac_link_down,
+ .mac_link_up = rtl838x_mac_link_up,
+};
+
+static const struct ethtool_ops rtl838x_ethtool_ops = {
+ .get_link_ksettings = rtl838x_get_link_ksettings,
+ .set_link_ksettings = rtl838x_set_link_ksettings,
+};
+
+static int __init rtl838x_eth_probe(struct platform_device *pdev)
+{
+ struct net_device *dev;
+ struct device_node *dn = pdev->dev.of_node;
+ struct rtl838x_eth_priv *priv;
+ struct resource *res, *mem;
+ const void *mac;
+ phy_interface_t phy_mode;
+ struct phylink *phylink;
+ int err = 0;
+
+ pr_info("Probing RTL838X eth device pdev: %x, dev: %x\n",
+ (u32)pdev, (u32)(&(pdev->dev)));
+
+ if (!dn) {
+ dev_err(&pdev->dev, "No DT found\n");
+ return -EINVAL;
+ }
+
+ dev = alloc_etherdev(sizeof(struct rtl838x_eth_priv));
+ if (!dev) {
+ err = -ENOMEM;
+ goto err_free;
+ }
+ SET_NETDEV_DEV(dev, &pdev->dev);
+ priv = netdev_priv(dev);
+
+ /* obtain buffer memory space */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (res) {
+ mem = devm_request_mem_region(&pdev->dev, res->start,
+ resource_size(res), res->name);
+ if (!mem) {
+ dev_err(&pdev->dev, "cannot request memory space\n");
+ err = -ENXIO;
+ goto err_free;
+ }
+
+ dev->mem_start = mem->start;
+ dev->mem_end = mem->end;
+ } else {
+ dev_err(&pdev->dev, "cannot request IO resource\n");
+ err = -ENXIO;
+ goto err_free;
+ }
+
+ /* Allocate buffer memory */
+ priv->membase = dmam_alloc_coherent(&pdev->dev,
+ sizeof(struct ring_b), (void *)&dev->mem_start,
+ GFP_KERNEL);
+ if (!priv->membase) {
+ dev_err(&pdev->dev, "cannot allocate DMA buffer\n");
+ err = -ENOMEM;
+ goto err_free;
+ }
+
+ spin_lock_init(&priv->lock);
+
+ /* obtain device IRQ number */
+ res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "cannot obtain IRQ, using default 24\n");
+ dev->irq = 24;
+ } else {
+ dev->irq = res->start;
+ }
+ dev->ethtool_ops = &rtl838x_ethtool_ops;
+
+ priv->id = soc_info.id;
+ priv->family_id = soc_info.family;
+ if (priv->id) {
+ pr_info("Found SoC ID: %4x: %s, family %x\n",
+ priv->id, soc_info.name, priv->family_id);
+ } else {
+ pr_err("Unknown chip id (%04x)\n", priv->id);
+ return -ENODEV;
+ }
+
+ if (priv->family_id == 0x8390) {
+ priv->cpu_port = RTL839X_CPU_PORT;
+ priv->r = &rtl839x_reg;
+ } else {
+ priv->cpu_port = RTL838X_CPU_PORT;
+ priv->r = &rtl838x_reg;
+ }
+
+ rtl8380_init_mac(priv);
+
+ /* try to get mac address in the following order:
+ * 1) from device tree data
+ * 2) from internal registers set by bootloader
+ */
+ mac = of_get_mac_address(pdev->dev.of_node);
+ if (!IS_ERR(mac)) {
+ memcpy(dev->dev_addr, mac, ETH_ALEN);
+ rtl838x_set_mac_hw(dev, (u8 *)mac);
+ } else {
+ dev->dev_addr[0] = (sw_r32(priv->r->mac) >> 8) & 0xff;
+ dev->dev_addr[1] = sw_r32(priv->r->mac) & 0xff;
+ dev->dev_addr[2] = (sw_r32(priv->r->mac + 4) >> 24) & 0xff;
+ dev->dev_addr[3] = (sw_r32(priv->r->mac + 4) >> 16) & 0xff;
+ dev->dev_addr[4] = (sw_r32(priv->r->mac + 4) >> 8) & 0xff;
+ dev->dev_addr[5] = sw_r32(priv->r->mac + 4) & 0xff;
+ }
+ /* if the address is invalid, use a random value */
+ if (!is_valid_ether_addr(dev->dev_addr)) {
+ struct sockaddr sa = { AF_UNSPEC };
+
+ netdev_warn(dev, "Invalid MAC address, using random\n");
+ eth_hw_addr_random(dev);
+ memcpy(sa.sa_data, dev->dev_addr, ETH_ALEN);
+ if (rtl838x_set_mac_address(dev, &sa))
+ netdev_warn(dev, "Failed to set MAC address.\n");
+ }
+ pr_info("Using MAC %08x%08x\n", sw_r32(priv->r->mac),
+ sw_r32(priv->r->mac + 4));
+ strcpy(dev->name, "eth%d");
+ dev->netdev_ops = &rtl838x_eth_netdev_ops;
+ priv->pdev = pdev;
+ priv->netdev = dev;
+
+ err = rtl838x_mdio_init(priv);
+ if (err)
+ goto err_free;
+
+ err = register_netdev(dev);
+ if (err)
+ goto err_free;
+
+ netif_napi_add(dev, &priv->napi, rtl838x_poll_rx, 64);
+ platform_set_drvdata(pdev, dev);
+
+ phy_mode = of_get_phy_mode(dn);
+ if (phy_mode < 0) {
+ dev_err(&pdev->dev, "incorrect phy-mode\n");
+ err = -EINVAL;
+ goto err_free;
+ }
+ priv->phylink_config.dev = &dev->dev;
+ priv->phylink_config.type = PHYLINK_NETDEV;
+
+ phylink = phylink_create(&priv->phylink_config, pdev->dev.fwnode,
+ phy_mode, &rtl838x_phylink_ops);
+ if (IS_ERR(phylink)) {
+ err = PTR_ERR(phylink);
+ goto err_free;
+ }
+ priv->phylink = phylink;
+ return 0;
+
+err_free:
+ pr_err("Error setting up netdev, freeing it again.\n");
+ free_netdev(dev);
+ return err;
+}
+
+static int rtl838x_eth_remove(struct platform_device *pdev)
+{
+ struct net_device *dev = platform_get_drvdata(pdev);
+ struct rtl838x_eth_priv *priv = netdev_priv(dev);
+
+ if (dev) {
+ pr_info("Removing platform driver for rtl838x-eth\n");
+ rtl838x_mdio_remove(priv);
+ rtl838x_hw_stop(priv);
+ netif_stop_queue(dev);
+ netif_napi_del(&priv->napi);
+ unregister_netdev(dev);
+ free_netdev(dev);
+ }
+ return 0;
+}
+
+static const struct of_device_id rtl838x_eth_of_ids[] = {
+ { .compatible = "realtek,rtl838x-eth"},
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, rtl838x_eth_of_ids);
+
+static struct platform_driver rtl838x_eth_driver = {
+ .probe = rtl838x_eth_probe,
+ .remove = rtl838x_eth_remove,
+ .driver = {
+ .name = "rtl838x-eth",
+ .pm = NULL,
+ .of_match_table = rtl838x_eth_of_ids,
+ },
+};
+
+module_platform_driver(rtl838x_eth_driver);
+
+MODULE_AUTHOR("B. Koblitz");
+MODULE_DESCRIPTION("RTL838X SoC Ethernet Driver");
+MODULE_LICENSE("GPL");
diff --git a/target/linux/rtl838x/files-5.4/drivers/net/ethernet/rtl838x_eth.h b/target/linux/rtl838x/files-5.4/drivers/net/ethernet/rtl838x_eth.h
new file mode 100644
index 0000000000..53ab7e5eb2
--- /dev/null
+++ b/target/linux/rtl838x/files-5.4/drivers/net/ethernet/rtl838x_eth.h
@@ -0,0 +1,261 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#ifndef _RTL838X_ETH_H
+#define _RTL838X_ETH_H
+
+/*
+ * Register definition
+ */
+
+#define RTL838X_CPU_PORT 28
+#define RTL839X_CPU_PORT 52
+
+#define RTL838X_MAC_PORT_CTRL (0xd560)
+#define RTL839X_MAC_PORT_CTRL (0x8004)
+#define RTL838X_DMA_IF_INTR_STS (0x9f54)
+#define RTL839X_DMA_IF_INTR_STS (0x7868)
+#define RTL838X_DMA_IF_INTR_MSK (0x9f50)
+#define RTL839X_DMA_IF_INTR_MSK (0x7864)
+#define RTL838X_DMA_IF_CTRL (0x9f58)
+#define RTL839X_DMA_IF_CTRL (0x786c)
+#define RTL838X_RST_GLB_CTRL_0 (0x003c)
+#define RTL838X_MAC_FORCE_MODE_CTRL (0xa104)
+#define RTL839X_MAC_FORCE_MODE_CTRL (0x02bc)
+
+/* MAC address settings */
+#define RTL838X_MAC (0xa9ec)
+#define RTL839X_MAC (0x02b4)
+#define RTL838X_MAC_ALE (0x6b04)
+#define RTL838X_MAC2 (0xa320)
+
+#define RTL838X_DMA_RX_BASE (0x9f00)
+#define RTL839X_DMA_RX_BASE (0x780c)
+#define RTL838X_DMA_TX_BASE (0x9f40)
+#define RTL839X_DMA_TX_BASE (0x784c)
+#define RTL838X_DMA_IF_RX_RING_SIZE (0xB7E4)
+#define RTL839X_DMA_IF_RX_RING_SIZE (0x6038)
+#define RTL838X_DMA_IF_RX_RING_CNTR (0xB7E8)
+#define RTL839X_DMA_IF_RX_RING_CNTR (0x603c)
+#define RTL838X_DMA_IF_RX_CUR (0x9F20)
+#define RTL839X_DMA_IF_RX_CUR (0x782c)
+
+#define RTL838X_DMY_REG31 (0x3b28)
+#define RTL838X_SDS_MODE_SEL (0x0028)
+#define RTL838X_SDS_CFG_REG (0x0034)
+#define RTL838X_INT_MODE_CTRL (0x005c)
+#define RTL838X_CHIP_INFO (0x00d8)
+#define RTL838X_SDS4_REG28 (0xef80)
+#define RTL838X_SDS4_DUMMY0 (0xef8c)
+#define RTL838X_SDS5_EXT_REG6 (0xf18c)
+#define RTL838X_PORT_ISO_CTRL(port) (0x4100 + ((port) << 2))
+#define RTL838X_STAT_PORT_STD_MIB(port) (0x1200 + (((port) << 8)))
+#define RTL838X_STAT_RST (0x3100)
+#define RTL838X_STAT_CTRL (0x3108)
+
+/* Registers of the internal Serdes of the 8380 */
+#define MAPLE_SDS4_REG0r RTL838X_SDS4_REG28
+#define MAPLE_SDS5_REG0r (RTL838X_SDS4_REG28 + 0x100)
+#define MAPLE_SDS4_REG3r RTL838X_SDS4_DUMMY0
+#define MAPLE_SDS5_REG3r (RTL838X_SDS4_REG28 + 0x100)
+#define MAPLE_SDS4_FIB_REG0r (RTL838X_SDS4_REG28 + 0x880)
+#define MAPLE_SDS5_FIB_REG0r (RTL838X_SDS4_REG28 + 0x980)
+
+/* VLAN registers */
+#define RTL838X_VLAN_PROFILE(idx) (0x3A88 + ((idx) << 2))
+#define RTL838X_VLAN_PORT_EGR_FLTR (0x3A84)
+#define RTL838X_VLAN_PORT_PB_VLAN(port) (0x3C00 + ((port) << 2))
+#define RTL838X_VLAN_PORT_IGR_FLTR_0 (0x3A7C)
+#define RTL838X_VLAN_PORT_IGR_FLTR_1 (0x3A7C + 4)
+#define RTL838X_TBL_ACCESS_CTRL_0 (0x6914)
+#define RTL838X_TBL_ACCESS_DATA_0(idx) (0x6918 + ((idx) << 2))
+#define RTL838X_TBL_ACCESS_CTRL_1 (0xA4C8)
+#define RTL838X_TBL_ACCESS_DATA_1(idx) (0xA4CC + ((idx) << 2))
+#define RTL839X_TBL_ACCESS_L2_CTRL (0x1180)
+#define RTL839X_TBL_ACCESS_L2_DATA(idx) (0x1184 + ((idx) << 2))
+/* MAC handling */
+#define RTL838X_MAC_LINK_STS (0xa188)
+#define RTL839X_MAC_LINK_STS (0x0390)
+#define RTL838X_MAC_LINK_SPD_STS (0xa190)
+#define RTL839X_MAC_LINK_SPD_STS (0x03a0)
+#define RTL838X_MAC_LINK_DUP_STS (0xa19c)
+#define RTL839X_MAC_LINK_DUP_STS (0x03b0)
+// TODO: RTL8390_MAC_LINK_MEDIA_STS_ADDR ???
+#define RTL838X_MAC_TX_PAUSE_STS (0xa1a0)
+#define RTL839X_MAC_TX_PAUSE_STS (0x03b8)
+#define RTL838X_MAC_RX_PAUSE_STS (0xa1a4)
+#define RTL839X_MAC_RX_PAUSE_STS (0x03c0)
+#define RTL838X_EEE_TX_TIMER_GIGA_CTRL (0xaa04)
+#define RTL838X_EEE_TX_TIMER_GELITE_CTRL (0xaa08)
+#define RTL839X_MAC_GLB_CTRL (0x02a8)
+#define RTL839X_SCHED_LB_TICK_TKN_CTRL (0x60f8)
+
+#define RTL838X_L2_TBL_FLUSH_CTRL (0x3370)
+#define RTL839X_L2_TBL_FLUSH_CTRL (0x3ba0)
+
+/* MAC link state bits */
+#define FORCE_EN (1 << 0)
+#define FORCE_LINK_EN (1 << 1)
+#define NWAY_EN (1 << 2)
+#define DUPLX_MODE (1 << 3)
+#define TX_PAUSE_EN (1 << 6)
+#define RX_PAUSE_EN (1 << 7)
+
+inline int rtl838x_mac_port_ctrl(int p)
+{
+ return RTL838X_MAC_PORT_CTRL + (p << 7);
+}
+
+inline int rtl839x_mac_port_ctrl(int p)
+{
+ return RTL839X_MAC_PORT_CTRL + (p << 7);
+}
+
+static inline int rtl838x_mac_force_mode_ctrl(int p)
+{
+ return RTL838X_MAC_FORCE_MODE_CTRL + (p << 2);
+}
+
+static inline int rtl839x_mac_force_mode_ctrl(int p)
+{
+ return RTL839X_MAC_FORCE_MODE_CTRL + (p << 2);
+}
+
+inline int rtl838x_dma_rx_base(int i)
+{
+ return RTL838X_DMA_RX_BASE + (i << 2);
+}
+
+inline int rtl839x_dma_rx_base(int i)
+{
+ return RTL839X_DMA_RX_BASE + (i << 2);
+}
+
+inline int rtl838x_dma_tx_base(int i)
+{
+ return RTL838X_DMA_TX_BASE + (i << 2);
+}
+
+inline int rtl839x_dma_tx_base(int i)
+{
+ return RTL839X_DMA_TX_BASE + (i << 2);
+}
+
+inline int rtl838x_dma_if_rx_ring_size(int i)
+{
+ return RTL838X_DMA_IF_RX_RING_SIZE + ((i >> 3) << 2);
+}
+
+inline int rtl839x_dma_if_rx_ring_size(int i)
+{
+ return RTL839X_DMA_IF_RX_RING_SIZE + ((i >> 3) << 2);
+}
+
+inline int rtl838x_dma_if_rx_ring_cntr(int i)
+{
+ return RTL838X_DMA_IF_RX_RING_CNTR + ((i >> 3) << 2);
+}
+
+inline int rtl839x_dma_if_rx_ring_cntr(int i)
+{
+ return RTL839X_DMA_IF_RX_RING_CNTR + ((i >> 3) << 2);
+}
+
+
+inline int rtl838x_dma_if_rx_cur(int i)
+{
+ return RTL838X_DMA_IF_RX_CUR + (i << 2);
+}
+
+inline int rtl839x_dma_if_rx_cur(int i)
+{
+ return RTL839X_DMA_IF_RX_CUR + (i << 2);
+}
+
+inline u32 rtl838x_get_mac_link_sts(int port)
+{
+ return (sw_r32(RTL838X_MAC_LINK_STS) & (1 << port));
+}
+
+inline u32 rtl839x_get_mac_link_sts(int p)
+{
+ return (sw_r32(RTL839X_MAC_LINK_STS + ((p >> 5) << 2)) & (1 << p));
+}
+
+inline u32 rtl838x_get_mac_link_dup_sts(int port)
+{
+ return (sw_r32(RTL838X_MAC_LINK_DUP_STS) & (1 << port));
+}
+
+inline u32 rtl839x_get_mac_link_dup_sts(int p)
+{
+ return (sw_r32(RTL839X_MAC_LINK_DUP_STS + ((p >> 5) << 2)) & (1 << p));
+}
+
+inline u32 rtl838x_get_mac_link_spd_sts(int port)
+{
+ int r = RTL838X_MAC_LINK_SPD_STS + ((port >> 4) << 2);
+ u32 speed = sw_r32(r);
+
+ speed >>= (port % 16) << 1;
+ return (speed & 0x3);
+}
+
+inline u32 rtl839x_get_mac_link_spd_sts(int port)
+{
+ int r = RTL839X_MAC_LINK_SPD_STS + ((port >> 4) << 2);
+ u32 speed = sw_r32(r);
+
+ speed >>= (port % 16) << 1;
+ return (speed & 0x3);
+}
+
+inline u32 rtl838x_get_mac_rx_pause_sts(int port)
+{
+ return (sw_r32(RTL838X_MAC_RX_PAUSE_STS) & (1 << port));
+}
+
+inline u32 rtl839x_get_mac_rx_pause_sts(int p)
+{
+ return (sw_r32(RTL839X_MAC_RX_PAUSE_STS + ((p >> 5) << 2)) & (1 << p));
+}
+
+inline u32 rtl838x_get_mac_tx_pause_sts(int port)
+{
+ return (sw_r32(RTL838X_MAC_TX_PAUSE_STS) & (1 << port));
+}
+
+inline u32 rtl839x_get_mac_tx_pause_sts(int p)
+{
+ return (sw_r32(RTL839X_MAC_TX_PAUSE_STS + ((p >> 5) << 2)) & (1 << p));
+}
+
+
+struct rtl838x_reg {
+ int (*mac_port_ctrl)(int port);
+ int dma_if_intr_sts;
+ int dma_if_intr_msk;
+ int dma_if_ctrl;
+ int (*mac_force_mode_ctrl)(int port);
+ int (*dma_rx_base)(int ring);
+ int (*dma_tx_base)(int ring);
+ int (*dma_if_rx_ring_size)(int ring);
+ int (*dma_if_rx_ring_cntr)(int ring);
+ int (*dma_if_rx_cur)(int ring);
+ int rst_glb_ctrl;
+ u32 (*get_mac_link_sts)(int port);
+ u32 (*get_mac_link_dup_sts)(int port);
+ u32 (*get_mac_link_spd_sts)(int port);
+ u32 (*get_mac_rx_pause_sts)(int port);
+ u32 (*get_mac_tx_pause_sts)(int port);
+ int mac;
+ int l2_tbl_flush_ctrl;
+};
+
+int rtl838x_write_phy(u32 port, u32 page, u32 reg, u32 val);
+int rtl838x_read_phy(u32 port, u32 page, u32 reg, u32 *val);
+int rtl839x_write_phy(u32 port, u32 page, u32 reg, u32 val);
+int rtl839x_read_phy(u32 port, u32 page, u32 reg, u32 *val);
+
+extern int rtl8380_sds_power(int mac, int val);
+
+#endif /* _RTL838X_ETH_H */
diff --git a/target/linux/rtl838x/image/Makefile b/target/linux/rtl838x/image/Makefile
new file mode 100644
index 0000000000..eef1fe0a33
--- /dev/null
+++ b/target/linux/rtl838x/image/Makefile
@@ -0,0 +1,44 @@
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+include $(TOPDIR)/rules.mk
+include $(INCLUDE_DIR)/image.mk
+
+KERNEL_LOADADDR = 0x80000000
+KERNEL_ENTRY = 0x80000400
+
+define Build/custom-uimage
+ mkimage -A $(LINUX_KARCH) \
+ -O linux -T kernel \
+ -C gzip -a $(KERNEL_LOADADDR) $(if $(UIMAGE_MAGIC),-M $(UIMAGE_MAGIC),) \
+ -e $(if $(KERNEL_ENTRY),$(KERNEL_ENTRY),$(KERNEL_LOADADDR)) \
+ -n '$(1)' -d $@ $@.new
+ mv $@.new $@
+endef
+
+
+define Device/Default
+ PROFILES = Default
+ KERNEL := kernel-bin | append-dtb | gzip | uImage gzip
+ KERNEL_INITRAMFS := kernel-bin | append-dtb | gzip | uImage gzip
+ DEVICE_DTS_DIR := ../dts
+ DEVICE_DTS = $$(SOC)_$(1)
+ SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
+ IMAGES := sysupgrade.bin
+ IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | append-rootfs | pad-rootfs | \
+ append-metadata | check-size
+endef
+
+define Device/allnet_all-sg8208m
+ SOC := rtl8382
+ IMAGE_SIZE := 7168k
+ DEVICE_VENDOR := ALLNET
+ DEVICE_MODEL := ALL-SG8208M
+ UIMAGE_MAGIC := 0x00000006
+ KERNEL := kernel-bin | append-dtb | gzip | custom-uimage 2.2.2.0
+ KERNEL_INITRAMFS := kernel-bin | append-dtb | gzip | custom-uimage 2.2.2.0
+ DEVICE_PACKAGES := ip-full ip-bridge kmod-gpio-button-hotplug tc
+endef
+TARGET_DEVICES += allnet_all-sg8208m
+
+$(eval $(call BuildImage))
diff --git a/target/linux/rtl838x/patches-5.4/300-mips-add-rtl838x-platform.patch b/target/linux/rtl838x/patches-5.4/300-mips-add-rtl838x-platform.patch
new file mode 100644
index 0000000000..34fb959a50
--- /dev/null
+++ b/target/linux/rtl838x/patches-5.4/300-mips-add-rtl838x-platform.patch
@@ -0,0 +1,42 @@
+--- a/arch/mips/Kbuild.platforms
++++ b/arch/mips/Kbuild.platforms
+@@ -27,6 +27,7 @@ platforms += pistachio
+ platforms += pmcs-msp71xx
+ platforms += pnx833x
+ platforms += ralink
++platforms += rtl838x
+ platforms += rb532
+ platforms += sgi-ip22
+ platforms += sgi-ip27
+--- a/arch/mips/Kconfig
++++ b/arch/mips/Kconfig
+@@ -629,6 +629,29 @@ config RALINK
+ select ARCH_HAS_RESET_CONTROLLER
+ select RESET_CONTROLLER
+
++config RTL838X
++ bool "Realtek based platforms"
++ select DMA_NONCOHERENT
++ select IRQ_MIPS_CPU
++ select CSRC_R4K
++ select CEVT_R4K
++ select SYS_HAS_CPU_MIPS32_R1
++ select SYS_HAS_CPU_MIPS32_R2
++ select SYS_SUPPORTS_BIG_ENDIAN
++ select SYS_SUPPORTS_32BIT_KERNEL
++ select SYS_SUPPORTS_MIPS16
++ select SYS_SUPPORTS_MULTITHREADING
++ select SYS_SUPPORTS_VPE_LOADER
++ select SYS_HAS_EARLY_PRINTK
++ select SWAP_IO_SPACE
++ select BOOT_RAW
++ select CLKDEV_LOOKUP
++ select PINCTRL
++ select ARCH_HAS_RESET_CONTROLLER
++ select RESET_CONTROLLER
++ select RTL8380_SERIES
++ select USE_OF
++
+ config SGI_IP22
+ bool "SGI IP22 (Indy/Indigo2)"
+ select FW_ARC
diff --git a/target/linux/rtl838x/patches-5.4/301-gpio-add-rtl838x-driver.patch b/target/linux/rtl838x/patches-5.4/301-gpio-add-rtl838x-driver.patch
new file mode 100644
index 0000000000..5eb8521ccb
--- /dev/null
+++ b/target/linux/rtl838x/patches-5.4/301-gpio-add-rtl838x-driver.patch
@@ -0,0 +1,25 @@
+--- a/drivers/gpio/Kconfig
++++ b/drivers/gpio/Kconfig
+@@ -441,6 +441,12 @@
+ A 32-bit single register GPIO fixed in/out implementation. This
+ can be used to represent any register as a set of GPIO signals.
+
++config GPIO_RTL838X
++ tristate "RTL838X GPIO"
++ depends on RTL838X
++ help
++ Say yes here to support RTL838X GPIO devices.
++
+ config GPIO_SAMA5D2_PIOBU
+ tristate "SAMA5D2 PIOBU GPIO support"
+ depends on MFD_SYSCON
+--- a/drivers/gpio/Makefile
++++ b/drivers/gpio/Makefile
+@@ -117,6 +117,7 @@
+ obj-$(CONFIG_GPIO_RCAR) += gpio-rcar.o
+ obj-$(CONFIG_GPIO_RDC321X) += gpio-rdc321x.o
+ obj-$(CONFIG_GPIO_REG) += gpio-reg.o
++obj-$(CONFIG_GPIO_RTL838X) += gpio-rtl838x.o
+ obj-$(CONFIG_ARCH_SA1100) += gpio-sa1100.o
+ obj-$(CONFIG_GPIO_SAMA5D2_PIOBU) += gpio-sama5d2-piobu.o
+ obj-$(CONFIG_GPIO_SCH311X) += gpio-sch311x.o
diff --git a/target/linux/rtl838x/patches-5.4/400-mtd-add-rtl838x-spi-flash-driver.patch b/target/linux/rtl838x/patches-5.4/400-mtd-add-rtl838x-spi-flash-driver.patch
new file mode 100644
index 0000000000..16cff75308
--- /dev/null
+++ b/target/linux/rtl838x/patches-5.4/400-mtd-add-rtl838x-spi-flash-driver.patch
@@ -0,0 +1,23 @@
+--- a/drivers/mtd/spi-nor/Kconfig
++++ b/drivers/mtd/spi-nor/Kconfig
+@@ -118,4 +118,13 @@ config SPI_INTEL_SPI_PLATFORM
+ To compile this driver as a module, choose M here: the module
+ will be called intel-spi-platform.
+
++config SPI_RTL838X
++ tristate "Realtek RTl838X SPI flash platform driver"
++ depends on RTL838X
++ help
++ This driver provides support for accessing SPI flash
++ in the RTL838X SoC.
++
++ Say N here unless you know what you are doing.
++
+ endif # MTD_SPI_NOR
+--- a/drivers/mtd/spi-nor/Makefile
++++ b/drivers/mtd/spi-nor/Makefile
+@@ -8,3 +8,4 @@ obj-$(CONFIG_SPI_NXP_SPIFI) += nxp-spifi
+ obj-$(CONFIG_SPI_INTEL_SPI) += intel-spi.o
+ obj-$(CONFIG_SPI_INTEL_SPI_PCI) += intel-spi-pci.o
+ obj-$(CONFIG_SPI_INTEL_SPI_PLATFORM) += intel-spi-platform.o
++obj-$(CONFIG_SPI_RTL838X) += rtl838x-nor.o
diff --git a/target/linux/rtl838x/patches-5.4/700-net-dsa-add-support-for-rtl838x-switch.patch b/target/linux/rtl838x/patches-5.4/700-net-dsa-add-support-for-rtl838x-switch.patch
new file mode 100644
index 0000000000..0082176d83
--- /dev/null
+++ b/target/linux/rtl838x/patches-5.4/700-net-dsa-add-support-for-rtl838x-switch.patch
@@ -0,0 +1,26 @@
+--- a/drivers/net/dsa/Kconfig
++++ b/drivers/net/dsa/Kconfig
+@@ -74,6 +74,13 @@ config NET_DSA_REALTEK_SMI
+ This enables support for the Realtek SMI-based switch
+ chips, currently only RTL8366RB.
+
++config NET_DSA_RTL838X
++ tristate "Realtek rtl838x switch support"
++ depends on RTL838X
++ select NET_DSA_TAG_TRAILER
++ ---help---
++ Say Y here if you want to use the Realtek rtl838x switch.
++
+ config NET_DSA_SMSC_LAN9303
+ tristate
+ select NET_DSA_TAG_LAN9303
+--- a/drivers/net/dsa/Makefile
++++ b/drivers/net/dsa/Makefile
+@@ -11,6 +11,7 @@ obj-$(CONFIG_NET_DSA_MV88E6060) += mv88e
+ obj-$(CONFIG_NET_DSA_QCA8K) += qca8k.o
+ obj-$(CONFIG_NET_DSA_REALTEK_SMI) += realtek-smi.o
+ realtek-smi-objs := realtek-smi-core.o rtl8366.o rtl8366rb.o
++obj-$(CONFIG_NET_DSA_RTL838X) += rtl838x_sw.o rtl838x_phy.o
+ obj-$(CONFIG_NET_DSA_SMSC_LAN9303) += lan9303-core.o
+ obj-$(CONFIG_NET_DSA_SMSC_LAN9303_I2C) += lan9303_i2c.o
+ obj-$(CONFIG_NET_DSA_SMSC_LAN9303_MDIO) += lan9303_mdio.o
diff --git a/target/linux/rtl838x/patches-5.4/701-net-dsa-add-rtl838x-support-for-tag-trailer.patch b/target/linux/rtl838x/patches-5.4/701-net-dsa-add-rtl838x-support-for-tag-trailer.patch
new file mode 100644
index 0000000000..d45c547803
--- /dev/null
+++ b/target/linux/rtl838x/patches-5.4/701-net-dsa-add-rtl838x-support-for-tag-trailer.patch
@@ -0,0 +1,37 @@
+--- a/net/dsa/tag_trailer.c
++++ b/net/dsa/tag_trailer.c
+@@ -44,7 +44,12 @@ static struct sk_buff *trailer_xmit(stru
+
+ trailer = skb_put(nskb, 4);
+ trailer[0] = 0x80;
++
++#ifdef CONFIG_NET_DSA_RTL838X
++ trailer[1] = dp->index;
++#else
+ trailer[1] = 1 << dp->index;
++#endif /* CONFIG_NET_DSA_RTL838X */
+ trailer[2] = 0x10;
+ trailer[3] = 0x00;
+
+@@ -61,12 +66,20 @@ static struct sk_buff *trailer_rcv(struc
+ return NULL;
+
+ trailer = skb_tail_pointer(skb) - 4;
++
++#ifdef CONFIG_NET_DSA_RTL838X
++ if (trailer[0] != 0x80 || (trailer[1] & 0xe0) != 0x00 ||
++ (trailer[2] & 0xef) != 0x00 || trailer[3] != 0x00)
++ return NULL;
++
++ source_port = trailer[1] & 0x1f;
++#else
+ if (trailer[0] != 0x80 || (trailer[1] & 0xf8) != 0x00 ||
+ (trailer[2] & 0xef) != 0x00 || trailer[3] != 0x00)
+ return NULL;
+
+ source_port = trailer[1] & 7;
+-
++#endif
+ skb->dev = dsa_master_find_slave(dev, 0, source_port);
+ if (!skb->dev)
+ return NULL;
diff --git a/target/linux/rtl838x/patches-5.4/702-net-dsa-increase-dsa-max-ports-for-rtl838x.patch b/target/linux/rtl838x/patches-5.4/702-net-dsa-increase-dsa-max-ports-for-rtl838x.patch
new file mode 100644
index 0000000000..5329dcad59
--- /dev/null
+++ b/target/linux/rtl838x/patches-5.4/702-net-dsa-increase-dsa-max-ports-for-rtl838x.patch
@@ -0,0 +1,13 @@
+Index: linux-5.4.24/include/linux/platform_data/dsa.h
+===================================================================
+--- linux-5.4.24.orig/include/linux/platform_data/dsa.h
++++ linux-5.4.24/include/linux/platform_data/dsa.h
+@@ -6,7 +6,7 @@ struct device;
+ struct net_device;
+
+ #define DSA_MAX_SWITCHES 4
+-#define DSA_MAX_PORTS 12
++#define DSA_MAX_PORTS 54
+ #define DSA_RTABLE_NONE -1
+
+ struct dsa_chip_data {
diff --git a/target/linux/rtl838x/patches-5.4/702-net-ethernet-add-support-for-rtl838x-ethernet.patch b/target/linux/rtl838x/patches-5.4/702-net-ethernet-add-support-for-rtl838x-ethernet.patch
new file mode 100644
index 0000000000..11e62450d5
--- /dev/null
+++ b/target/linux/rtl838x/patches-5.4/702-net-ethernet-add-support-for-rtl838x-ethernet.patch
@@ -0,0 +1,26 @@
+--- a/drivers/net/ethernet/Kconfig
++++ b/drivers/net/ethernet/Kconfig
+@@ -163,6 +163,13 @@ source "drivers/net/ethernet/rdc/Kconfig
+ source "drivers/net/ethernet/realtek/Kconfig"
+ source "drivers/net/ethernet/renesas/Kconfig"
+ source "drivers/net/ethernet/rocker/Kconfig"
++
++config NET_RTL838X
++ tristate "Realtek rtl838x Ethernet MAC support"
++ depends on RTL838X
++ ---help---
++ Say Y here if you want to use the Realtek rtl838x Gbps Ethernet MAC.
++
+ source "drivers/net/ethernet/samsung/Kconfig"
+ source "drivers/net/ethernet/seeq/Kconfig"
+ source "drivers/net/ethernet/sfc/Kconfig"
+--- a/drivers/net/ethernet/Makefile
++++ b/drivers/net/ethernet/Makefile
+@@ -76,6 +76,7 @@ obj-$(CONFIG_NET_VENDOR_REALTEK) += real
+ obj-$(CONFIG_NET_VENDOR_RENESAS) += renesas/
+ obj-$(CONFIG_NET_VENDOR_RDC) += rdc/
+ obj-$(CONFIG_NET_VENDOR_ROCKER) += rocker/
++obj-$(CONFIG_NET_RTL838X) += rtl838x_eth.o
+ obj-$(CONFIG_NET_VENDOR_SAMSUNG) += samsung/
+ obj-$(CONFIG_NET_VENDOR_SEEQ) += seeq/
+ obj-$(CONFIG_NET_VENDOR_SILAN) += silan/
diff --git a/target/linux/rtl838x/patches-5.4/703-include-linux-add-phy-ops-for-rtl838x.patch b/target/linux/rtl838x/patches-5.4/703-include-linux-add-phy-ops-for-rtl838x.patch
new file mode 100644
index 0000000000..db8b0403f7
--- /dev/null
+++ b/target/linux/rtl838x/patches-5.4/703-include-linux-add-phy-ops-for-rtl838x.patch
@@ -0,0 +1,13 @@
+--- a/include/linux/phy.h
++++ b/include/linux/phy.h
+@@ -628,6 +628,10 @@
+ struct ethtool_tunable *tuna,
+ const void *data);
+ int (*set_loopback)(struct phy_device *dev, bool enable);
++ int (*get_port)(struct phy_device *dev);
++ int (*set_port)(struct phy_device *dev, int port);
++ int (*get_eee)(struct phy_device *dev, struct ethtool_eee *e);
++ int (*set_eee)(struct phy_device *dev, struct ethtool_eee *e);
+ };
+ #define to_phy_driver(d) container_of(to_mdio_common_driver(d), \
+ struct phy_driver, mdiodrv)
diff --git a/target/linux/rtl838x/patches-5.4/704-drivers-net-phy-eee-support-for-rtl838x.patch b/target/linux/rtl838x/patches-5.4/704-drivers-net-phy-eee-support-for-rtl838x.patch
new file mode 100644
index 0000000000..5262be53c6
--- /dev/null
+++ b/target/linux/rtl838x/patches-5.4/704-drivers-net-phy-eee-support-for-rtl838x.patch
@@ -0,0 +1,41 @@
+--- a/drivers/net/phy/phylink.c
++++ b/drivers/net/phy/phylink.c
+@@ -1244,6 +1244,11 @@
+
+ /* If we have a PHY, configure the phy */
+ if (pl->phydev) {
++ if (pl->phydev->drv->get_port && pl->phydev->drv->set_port) {
++ if(pl->phydev->drv->get_port(pl->phydev) != kset->base.port) {
++ pl->phydev->drv->set_port(pl->phydev, kset->base.port);
++ }
++ }
+ ret = phy_ethtool_ksettings_set(pl->phydev, &our_kset);
+ if (ret)
+ return ret;
+@@ -1422,8 +1427,11 @@
+
+ ASSERT_RTNL();
+
+- if (pl->phydev)
++ if (pl->phydev) {
++ if (pl->phydev->drv->get_eee)
++ return pl->phydev->drv->get_eee(pl->phydev, eee);
+ ret = phy_ethtool_get_eee(pl->phydev, eee);
++ }
+
+ return ret;
+ }
+@@ -1440,9 +1448,11 @@
+
+ ASSERT_RTNL();
+
+- if (pl->phydev)
++ if (pl->phydev) {
++ if (pl->phydev->drv->set_eee)
++ return pl->phydev->drv->set_eee(pl->phydev, eee);
+ ret = phy_ethtool_set_eee(pl->phydev, eee);
+-
++ }
+ return ret;
+ }
+ EXPORT_SYMBOL_GPL(phylink_ethtool_set_eee);
diff --git a/target/linux/rtl838x/profiles/00-default.mk b/target/linux/rtl838x/profiles/00-default.mk
new file mode 100644
index 0000000000..d6890a815a
--- /dev/null
+++ b/target/linux/rtl838x/profiles/00-default.mk
@@ -0,0 +1,13 @@
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/Default
+ NAME:=Default Profile
+ PRIORITY:=1
+endef
+
+define Profile/Default/Description
+ Default package set compatible with most boards.
+endef
+$(eval $(call Profile,Default))
More information about the lede-commits
mailing list