[openwrt/openwrt] lantiq: add support for AVM FRITZ!Box 7430
LEDE Commits
lede-commits at lists.infradead.org
Tue Oct 27 09:22:57 EDT 2020
adrian pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/6c85a449a988876fdfd4ce84d6aa5ffe4a2820c1
commit 6c85a449a988876fdfd4ce84d6aa5ffe4a2820c1
Author: Leon Maurice Adam <leon.adam at aol.de>
AuthorDate: Sun May 3 12:44:24 2020 +0200
lantiq: add support for AVM FRITZ!Box 7430
Hardware:
- SoC: Lantiq VRX 220
- CPU: 2x MIPS 34Kc 500 MHz
- RAM: 128 MiB 250 MHz
- Flash: 128 MiB NAND
- Ethernet: Built-in Fast Ethernet switch, 4 ports used
- Wifi: Atheros AR9381-AL1A b/g/n with 2 pcb/internal and 1 external antennas
- USB: 1x USB 2.0
- DSL: Built-in A/VDSL2 modem
- DECT: Dialog SC14441
- LEDs: 1 two-color, 4 one-color
- Buttons: 1x DECT, 1x WIFI
- Telephone connectors: 1 FXS port via TAE or RJ11 connector
With the exception of FXS/DECT everything works
(there are no drivers for AVM's FXS or DECT implementation),
DSL is yet untested.
Installation:
Boot up the device and wait a few seconds. Run the eva_ramboot.py script
in scripts/flashing/ to load the initramfs image on the device:
$ ./scripts/flashing/eva_ramboot.py 192.168.178.1 <path to your initramfs image>
If the script fails to reach the device, maybe try 169.254.120.1.
Wait until booting is complete. You should now be able to reach your device
under the default ip address 192.168.1.1.
Before flashing, check if linux_fs_start is not set to 1 in the tffs partition:
$ fritz_tffs_nand -d /dev/mtd1 -n linux_fs_start
If linux_fs_start is 1, you will need to reset it to 0, either by FTP,
upgrading FritzOS or doing a recovery.
Now you should be able to flash the device using sysupgrade.
Signed-off-by: Leon Maurice Adam <leon.adam at aol.de>
Acked-by: Aleksander Jan Bajkowski <A.Bajkowski at stud.elka.pw.edu.pl>
[drop BOARD_NAME, use wpad-basic-wolfssl, drop 4.19, drop dts-v1,
remove model prefix from LED names]
Signed-off-by: Adrian Schmutzler <freifunk at adrianschmutzler.de>
---
.../mips/boot/dts/lantiq/vr9_avm_fritz7430.dts | 273 +++++++++++++++++++++
target/linux/lantiq/image/vr9.mk | 10 +
.../xrx200/base-files/etc/board.d/02_network | 10 +-
.../etc/hotplug.d/firmware/12-ath9k-eeprom | 3 +-
.../xrx200/base-files/lib/upgrade/platform.sh | 1 +
5 files changed, 294 insertions(+), 3 deletions(-)
diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/lantiq/vr9_avm_fritz7430.dts b/target/linux/lantiq/files/arch/mips/boot/dts/lantiq/vr9_avm_fritz7430.dts
new file mode 100644
index 0000000000..3894fecb43
--- /dev/null
+++ b/target/linux/lantiq/files/arch/mips/boot/dts/lantiq/vr9_avm_fritz7430.dts
@@ -0,0 +1,273 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "vr9.dtsi"
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/mips/lantiq_rcu_gphy.h>
+
+/ {
+ compatible = "avm,fritz7430", "lantiq,xway", "lantiq,vr9";
+ model = "AVM FRITZ!Box 7430";
+
+ chosen {
+ bootargs = "console=ttyLTQ0,115200";
+ };
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_info_red;
+ led-running = &led_power;
+ led-upgrade = &led_info_green;
+
+ led-dsl = &led_info_green;
+ led-wifi = &led_wifi;
+ };
+
+ memory at 0 {
+ device_type = "memory";
+ reg = <0x0 0x8000000>;
+ };
+
+ keys {
+ compatible = "gpio-keys-polled";
+ poll-interval = <100>;
+
+ dect {
+ label = "dect";
+ gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_PHONE>;
+ };
+
+ wifi {
+ label = "wifi";
+ gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RFKILL>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ label = "green:power";
+ gpios = <&gpio 31 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ };
+
+ led_info_green: info_green {
+ label = "green:info";
+ gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+ };
+
+ led_info_red: info_red {
+ label = "red:info";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ };
+
+ led_wifi: wifi {
+ label = "green:wifi";
+ gpios = <&gpio 34 GPIO_ACTIVE_LOW>;
+ };
+
+ dect {
+ label = "green:dect";
+ gpios = <&gpio 35 GPIO_ACTIVE_LOW>;
+ };
+
+ fon {
+ label = "green:fon";
+ gpios = <&gpio 36 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ usb0_vbus: regulator-usb0-vbus {
+ compatible = "regulator-fixed";
+
+ regulator-name = "USB0_VBUS";
+
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+
+ gpio = <&gpio 5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&localbus {
+ flash at 0 {
+ compatible = "lantiq,nand-xway";
+ bank-width = <2>;
+ reg = <0 0x0 0x8000000>;
+ lantiq,cs = <1>;
+
+ pinctrl-0 = <&nand_pins>, <&nand_cs1_pins>;
+ pinctrl-names = "default";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "urlader";
+ reg = <0x0 0x40000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "nand-tffs";
+ reg = <0x40000 0x400000>;
+ read-only;
+ };
+
+ partition at 440000 {
+ label = "kernel";
+ reg = <0x440000 0x400000>;
+ };
+
+ partition at 840000 {
+ label = "ubi";
+ reg = <0x840000 0x3000000>;
+ };
+
+ partition at 3840000 {
+ label = "reserved-kernel";
+ reg = <0x3840000 0x400000>;
+ read-only;
+ };
+
+ partition at 3c40000 {
+ label = "reserved-filesystem";
+ reg = <0x3c40000 0x3000000>;
+ read-only;
+ };
+
+ partition at 6c40000 {
+ label = "config";
+ reg = <0x6c40000 0x200000>;
+ read-only;
+ };
+
+ partition at 6e40000 {
+ label = "nand-filesystem";
+ reg = <0x6e40000 0x11c0000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&pcie0 {
+ status = "okay";
+
+ gpio-reset = <&gpio 11 GPIO_ACTIVE_LOW>;
+
+ pcie at 0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+
+ wifi at 168c,abcd {
+ compatible = "pci168c,abcd";
+ reg = <0 0 0 0 0>;
+ qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:01:00.0.bin */
+ };
+ };
+};
+
+&gphy0 {
+ lantiq,gphy-mode = <GPHY_MODE_FE>;
+};
+
+&gphy1 {
+ lantiq,gphy-mode = <GPHY_MODE_FE>;
+};
+
+ð0 {
+ interface at 0 {
+ compatible = "lantiq,xrx200-pdi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ lantiq,switch;
+
+ ethernet at 2 {
+ compatible = "lantiq,xrx200-pdi-port";
+ reg = <2>;
+ phy-mode = "mii";
+ phy-handle = <&phy11>;
+ };
+
+ ethernet at 3 {
+ compatible = "lantiq,xrx200-pdi-port";
+ reg = <3>;
+ phy-mode = "mii";
+ phy-handle = <&phy12>;
+ };
+
+ ethernet at 4 {
+ compatible = "lantiq,xrx200-pdi-port";
+ reg = <4>;
+ phy-mode = "mii";
+ phy-handle = <&phy13>;
+ };
+
+ ethernet at 5 {
+ compatible = "lantiq,xrx200-pdi-port";
+ reg = <5>;
+ phy-mode = "mii";
+ phy-handle = <&phy14>;
+ };
+ };
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "lantiq,xrx200-mdio";
+
+ phy11: ethernet-phy at 11 {
+ reg = <0x11>;
+ compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22";
+ };
+
+ phy12: ethernet-phy at 12 {
+ reg = <0x12>;
+ compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22";
+ };
+
+ phy13: ethernet-phy at 13 {
+ reg = <0x13>;
+ compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22";
+ };
+
+ phy14: ethernet-phy at 14 {
+ reg = <0x14>;
+ compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22";
+ };
+ };
+};
+
+&gpio {
+ pinctrl-names = "default";
+ pinctrl-0 = <&state_default>;
+
+ state_default: pinmux {
+ pcie-rst {
+ lantiq,pins = "io11";
+ lantiq,open-drain = <1>;
+ lantiq,output = <1>;
+ };
+ };
+};
+
+&usb_phy0 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+
+ vbus-supply = <&usb0_vbus>;
+};
diff --git a/target/linux/lantiq/image/vr9.mk b/target/linux/lantiq/image/vr9.mk
index e5ebbd3b65..d3420bb2b9 100644
--- a/target/linux/lantiq/image/vr9.mk
+++ b/target/linux/lantiq/image/vr9.mk
@@ -157,6 +157,16 @@ define Device/avm_fritz7412
endef
TARGET_DEVICES += avm_fritz7412
+define Device/avm_fritz7430
+ $(Device/AVM)
+ $(Device/NAND)
+ DEVICE_MODEL := FRITZ!Box 7430
+ KERNEL_SIZE := 4096k
+ IMAGE_SIZE := 49152k
+ DEVICE_PACKAGES := kmod-ath9k kmod-owl-loader wpad-basic-wolfssl fritz-tffs-nand fritz-caldata
+endef
+TARGET_DEVICES += avm_fritz7430
+
define Device/bt_homehub-v5a
$(Device/NAND)
DEVICE_VENDOR := British Telecom
diff --git a/target/linux/lantiq/xrx200/base-files/etc/board.d/02_network b/target/linux/lantiq/xrx200/base-files/etc/board.d/02_network
index 07bcdf9f84..f7af17995f 100755
--- a/target/linux/lantiq/xrx200/base-files/etc/board.d/02_network
+++ b/target/linux/lantiq/xrx200/base-files/etc/board.d/02_network
@@ -44,6 +44,10 @@ lantiq_setup_interfaces()
ucidef_add_switch "switch0" \
"0:lan:3" "1:lan:4" "2:lan:2" "4:lan:1" "6t at eth0"
;;
+ avm,fritz7430)
+ ucidef_add_switch "switch0" \
+ "2:lan:3" "3:lan:4" "4:lan:1" "5:lan:2" "6t at eth0"
+ ;;
bt,homehub-v5a)
ucidef_add_switch "switch0" \
"0:lan:3" "1:lan:4" "2:lan:2" "4:lan:1" "5:wan:5" "6t at eth0"
@@ -85,7 +89,8 @@ lantiq_setup_dsl()
avm,fritz3370-rev2-micron|\
avm,fritz7360sl|\
avm,fritz7362sl|\
- avm,fritz7412)
+ avm,fritz7412|\
+ avm,fritz7430)
annex="b"
;;
esac
@@ -135,7 +140,8 @@ lantiq_setup_macs()
lan_mac=$(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)"))
wan_mac=$(fritz_tffs -n macdsl -i $(find_mtd_part "tffs (1)"))
;;
- avm,fritz7412)
+ avm,fritz7412|\
+ avm,fritz7430)
tffsdev=$(find_mtd_chardev "nand-tffs")
lan_mac=$(/usr/bin/fritz_tffs_nand -d $tffsdev -n maca -o)
wan_mac=$(/usr/bin/fritz_tffs_nand -d $tffsdev -n macdsl -o)
diff --git a/target/linux/lantiq/xrx200/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom b/target/linux/lantiq/xrx200/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom
index 75cc50a207..ee8cc3879a 100644
--- a/target/linux/lantiq/xrx200/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom
+++ b/target/linux/lantiq/xrx200/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom
@@ -20,7 +20,8 @@ case "$FIRMWARE" in
avm,fritz7360-v2)
caldata_extract "urlader" 0x985 0x1000
;;
- avm,fritz7412)
+ avm,fritz7412|\
+ avm,fritz7430)
/usr/bin/fritz_cal_extract -i 1 -s 0x1e000 -e 0x207 -l 4096 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader")
;;
bt,homehub-v5a)
diff --git a/target/linux/lantiq/xrx200/base-files/lib/upgrade/platform.sh b/target/linux/lantiq/xrx200/base-files/lib/upgrade/platform.sh
index dcd797c30d..0770052488 100755
--- a/target/linux/lantiq/xrx200/base-files/lib/upgrade/platform.sh
+++ b/target/linux/lantiq/xrx200/base-files/lib/upgrade/platform.sh
@@ -13,6 +13,7 @@ platform_do_upgrade() {
avm,fritz3370-rev2-micron|\
avm,fritz7362sl|\
avm,fritz7412|\
+ avm,fritz7430|\
bt,homehub-v5a|\
zyxel,p-2812hnu-f1|\
zyxel,p-2812hnu-f3)
More information about the lede-commits
mailing list