[openwrt/openwrt] ath79: add support for Qxwlan E1700AC v2

LEDE Commits lede-commits at lists.infradead.org
Sat Oct 17 14:48:45 EDT 2020


adrian pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/4ff7bdfeebd4c974b74df74f779fc10891898f5d

commit 4ff7bdfeebd4c974b74df74f779fc10891898f5d
Author: 张鹏 <sd20 at qxwlan.com>
AuthorDate: Fri Oct 16 12:53:51 2020 +0200

    ath79: add support for Qxwlan E1700AC v2
    
    E1700AC v2 based on Qualcomm/Atheros QCA9563 + QCA9880.
    
    Specification:
    
     - 750/400/250 MHz (CPU/DDR/AHB)
     - 128 MB of RAM (DDR2)
     - 8/16 MB of FLASH (SPI NOR)
     - 3T3R 2.4 GHz
     - 3T3R 5 GHz
     - 2 x 10/1000M Mbps Ethernet (RJ45)
     - 1 x MiniPCI-e
     - 1 x SIM (3G/4G)
     - 1 x USB 2.0 Port
     - 5 x LED , 2 x Button(S8-Reset Buttun), 1 x power input
     - UART (J5) header on PCB (115200 8N1)
    
    Flash instruction:
    
       1.Using tftp mode with UART connection and original LEDE image
          - Configure PC with static IP 192.168.1.10 and tftp server.
          - Rename "openwrt-ar71xx-generic-xxx-squashfs-sysupgrade.bin"
            to "firmware.bin" and place it in tftp server directory.
          - Connect PC with one of LAN ports, power up the router and press
            key "Enter" to access U-Boot CLI.
          - Use the following commands to update the device to LEDE:
            run lfw
          - After that the device will reboot and boot to LEDE.
          - Wait until all LEDs stops flashing and use the router.
    
       2.Using httpd mode with Web UI connection and original LEDE image
          - Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
          - Connect PC with one of LAN ports,press the reset button, power up
            the router and keep button pressed for around 6-7 seconds, until
            leds flashing.
          - Open your browser and enter 192.168.1.1,You will see the upgrade
            interface, select "openwrt-ar71xx-generic-xxx-squashfs-
            sysupgrade.bin" and click the upgrade button.
          - After that the device will reboot and boot to LEDE.
          - Wait until all LEDs stops flashing and use the router.
    
    Signed-off-by: 张鹏 <sd20 at qxwlan.com>
    [cut out of bigger patch, keep swconfig, whitespace fixes]
    Signed-off-by: Adrian Schmutzler <freifunk at adrianschmutzler.de>
---
 .../ath79/dts/qca9563_qxwlan_e1700ac-v2-16m.dts    |  16 +++
 .../ath79/dts/qca9563_qxwlan_e1700ac-v2-8m.dts     |  16 +++
 target/linux/ath79/dts/qca9563_qxwlan_e1700ac.dtsi | 157 +++++++++++++++++++++
 .../generic/base-files/etc/board.d/02_network      |   2 +
 .../etc/hotplug.d/firmware/11-ath10k-caldata       |   2 +
 target/linux/ath79/image/generic.mk                |  21 +++
 6 files changed, 214 insertions(+)

diff --git a/target/linux/ath79/dts/qca9563_qxwlan_e1700ac-v2-16m.dts b/target/linux/ath79/dts/qca9563_qxwlan_e1700ac-v2-16m.dts
new file mode 100644
index 0000000000..b851380a47
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_qxwlan_e1700ac-v2-16m.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca9563_qxwlan_e1700ac.dtsi"
+
+/ {
+	model = "Qxwlan E1700AC v2 16M";
+	compatible = "qxwlan,e1700ac-v2-16m", "qca,qca9563";
+};
+
+&partitions {
+	partition at 70000 {
+		compatible = "denx,uimage";
+		label = "firmware";
+		reg = <0x070000 0xf90000>;
+	};
+};
diff --git a/target/linux/ath79/dts/qca9563_qxwlan_e1700ac-v2-8m.dts b/target/linux/ath79/dts/qca9563_qxwlan_e1700ac-v2-8m.dts
new file mode 100644
index 0000000000..7aaac487c2
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_qxwlan_e1700ac-v2-8m.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca9563_qxwlan_e1700ac.dtsi"
+
+/ {
+	model = "Qxwlan E1700AC v2 8M";
+	compatible = "qxwlan,e1700ac-v2-8m", "qca,qca9563";
+};
+
+&partitions {
+	partition at 70000 {
+		compatible = "denx,uimage";
+		label = "firmware";
+		reg = <0x070000 0x790000>;
+	};
+};
diff --git a/target/linux/ath79/dts/qca9563_qxwlan_e1700ac.dtsi b/target/linux/ath79/dts/qca9563_qxwlan_e1700ac.dtsi
new file mode 100644
index 0000000000..0c397e7dd9
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_qxwlan_e1700ac.dtsi
@@ -0,0 +1,157 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca956x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	aliases {
+		label-mac-device = &eth0;
+		led-boot = &led_system;
+		led-failsafe = &led_system;
+		led-running = &led_system;
+		led-upgrade = &led_system;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_system: system {
+			label = "green:system";
+			gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		usb {
+			label = "green:usb";
+			gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&hub_port0>;
+			linux,default-trigger = "usbport";
+		};
+
+		wlan2g {
+			label = "green:wlan2g";
+			gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy1tpt";
+		};
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&spi {
+	status = "okay";
+
+	num-cs = <1>;
+
+	flash at 0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <25000000>;
+
+		partitions: partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition at 0 {
+				label = "u-boot";
+				reg = <0x000000 0x040000>;
+				read-only;
+			};
+
+			partition at 40000 {
+				label = "u-boot-env";
+				reg = <0x040000 0x010000>;
+				read-only;
+			};
+
+			pridata: partition at 50000 {
+				label = "pri-data";
+				reg = <0x050000 0x010000>;
+				read-only;
+			};
+
+			art: partition at 60000 {
+				label = "art";
+				reg = <0x060000 0x010000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	phy-mask = <0>;
+
+	phy0: ethernet-phy at 0 {
+		reg = <0>;
+		phy-mode = "sgmii";
+		qca,mib-poll-interval = <500>;
+
+		qca,ar8327-initvals = <
+			0x04 0x00080080 /* PORT0 PAD MODE CTRL */
+			0x7c 0x0000007e /* PORT0_STATUS */
+		>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	pll-data = <0x03000101 0x00000101 0x00001919>;
+
+	phy-mode = "sgmii";
+	phy-handle = <&phy0>;
+
+	mtd-mac-address = <&pridata 0x400>;
+};
+
+&usb_phy0 {
+	status = "okay";
+};
+
+&usb0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	hub_port0: port at 1 {
+		reg = <1>;
+		#trigger-source-cells = <0>;
+	};
+};
+
+&usb_phy1 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
+
+&uart {
+	status = "okay";
+};
+
+&wmac {
+	status = "okay";
+
+	mtd-cal-data = <&art 0x1000>;
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index 8f528c33cd..a587cfac96 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -244,6 +244,8 @@ ath79_setup_interfaces()
 			"0 at eth0" "2:lan:1" "3:lan:2" "4:lan:3" "5:lan:4" "1:wan"
 		;;
 	nec,wg1200cr|\
+	qxwlan,e1700ac-v2-8m|\
+	qxwlan,e1700ac-v2-16m|\
 	qxwlan,e750g-v8-8m|\
 	qxwlan,e750g-v8-16m|\
 	ubnt,nanostation-ac|\
diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 857f566db8..25e864ba72 100644
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -22,6 +22,8 @@ case "$FIRMWARE" in
 	comfast,cf-wr650ac-v1|\
 	comfast,cf-wr650ac-v2|\
 	devolo,magic-2-wifi|\
+	qxwlan,e1700ac-v2-8m|\
+	qxwlan,e1700ac-v2-16m|\
 	ubnt,unifiac-lite|\
 	ubnt,unifiac-lr|\
 	ubnt,unifiac-mesh|\
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index 528a63f629..8b0c247876 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -1475,6 +1475,27 @@ define Device/qihoo_c301
 endef
 TARGET_DEVICES += qihoo_c301
 
+define Device/qxwlan_e1700ac-v2
+  SOC := qca9563
+  DEVICE_VENDOR := Qxwlan
+  DEVICE_MODEL := E1700AC
+  DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
+endef
+
+define Device/qxwlan_e1700ac-v2-16m
+  $(Device/qxwlan_e1700ac-v2)
+  DEVICE_VARIANT := v2 (16M)
+  IMAGE_SIZE := 15936k
+endef
+TARGET_DEVICES += qxwlan_e1700ac-v2-16m
+
+define Device/qxwlan_e1700ac-v2-8m
+  $(Device/qxwlan_e1700ac-v2)
+  DEVICE_VARIANT := v2 (8M)
+  IMAGE_SIZE := 7744k
+endef
+TARGET_DEVICES += qxwlan_e1700ac-v2-8m
+
 define Device/qxwlan_e558-v2
   SOC := qca9558
   DEVICE_VENDOR := Qxwlan



More information about the lede-commits mailing list