[openwrt/openwrt] ath79: support for TP-Link EAP225-Outdoor v1
LEDE Commits
lede-commits at lists.infradead.org
Mon Nov 23 16:53:53 EST 2020
ynezz pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/4f86edf477edbc0f20b5a49a69f658fa82158284
commit 4f86edf477edbc0f20b5a49a69f658fa82158284
Author: Sander Vanheule <sander at svanheule.net>
AuthorDate: Tue Jul 7 18:04:37 2020 +0200
ath79: support for TP-Link EAP225-Outdoor v1
TP-Link EAP225-Outdoor v1 is an AC1200 (802.11ac Wave-2) pole or wall
mount access point. Debricking requires access to the serial port, which
is non-trivial.
Device specifications:
* SoC: QCA9563 @ 775MHz
* Memory: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n 2x2
* Wireless 5GHz (QCA9886): a/n/ac 2x2 MU-MIMO
* Ethernet (AR8033): 1× 1GbE, PoE
Flashing instructions:
* ssh into target device with recent (>= v1.6.0) firmware
* run `cliclientd stopcs` on target device
* upload factory image via web interface
Debricking:
To recover the device, you need access to the serial port. This requires
fine soldering to test points, or the use of probe pins.
* Open the case and solder wires to the test points: RXD, TXD and TPGND4
* Use a 3.3V UART, 115200 baud, 8n1
* Interrupt bootloader by holding ctrl+B during boot
* upload initramfs via built-in tftp client and perform sysupgrade
setenv ipaddr 192.168.1.1 # default, change as required
setenv serverip 192.168.1.10 # default, change as required
tftp 0x80800000 initramfs.bin
bootelf $fileaddr
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From stock ifconfig:
ath0 Link encap:Ethernet HWaddr D8:...:2E
ath10 Link encap:Ethernet HWaddr D8:...:2F
br0 Link encap:Ethernet HWaddr D8:...:2E
eth0 Link encap:Ethernet HWaddr D8:...:2E
Tested by forum user PolynomialDivision on firmware v1.7.0.
UART access tested by forum user arinc9.
Signed-off-by: Sander Vanheule <sander at svanheule.net>
---
.../ath79/dts/qca9563_tplink_eap225-outdoor-v1.dts | 30 ++++++++++++++++++++++
.../generic/base-files/etc/board.d/02_network | 1 +
.../etc/hotplug.d/firmware/11-ath10k-caldata | 1 +
target/linux/ath79/image/generic-tp-link.mk | 11 ++++++++
tools/firmware-utils/src/tplink-safeloader.c | 29 +++++++++++++++++++++
5 files changed, 72 insertions(+)
diff --git a/target/linux/ath79/dts/qca9563_tplink_eap225-outdoor-v1.dts b/target/linux/ath79/dts/qca9563_tplink_eap225-outdoor-v1.dts
new file mode 100644
index 0000000000..fc6d3365a0
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_tplink_eap225-outdoor-v1.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca9563_tplink_eap2x5-1port.dtsi"
+
+/ {
+ compatible = "tplink,eap225-outdoor-v1", "qca,qca9563";
+ model = "TP-Link EAP225-Outdoor v1";
+
+ aliases {
+ led-boot = &led_status_green;
+ led-failsafe = &led_status_amber;
+ led-running = &led_status_green;
+ led-upgrade = &led_status_amber;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_status_green: status_green {
+ label = "green:status";
+ gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ led_status_amber: status_amber {
+ label = "amber:status";
+ gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index c29c4006c8..928b6c8903 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -48,6 +48,7 @@ ath79_setup_interfaces()
tplink,cpe510-v3|\
tplink,cpe610-v1|\
tplink,cpe610-v2|\
+ tplink,eap225-outdoor-v1|\
tplink,eap245-v1|\
tplink,re350k-v1|\
tplink,re355-v1|\
diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 5229ad17f4..5be1c72ab0 100644
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -208,6 +208,7 @@ case "$FIRMWARE" in
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
;;
+ tplink,eap225-outdoor-v1|\
tplink,eap225-wall-v2|\
tplink,tl-wpa8630p-v2-int|\
tplink,tl-wpa8630p-v2.0-eu|\
diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk
index c704d99c98..343ea963c3 100644
--- a/target/linux/ath79/image/generic-tp-link.mk
+++ b/target/linux/ath79/image/generic-tp-link.mk
@@ -371,6 +371,17 @@ define Device/tplink-eap2x5
pad-extra 128
endef
+define Device/tplink_eap225-outdoor-v1
+ $(Device/tplink-eap2x5)
+ SOC := qca9563
+ IMAGE_SIZE := 13824k
+ DEVICE_MODEL := EAP225-Outdoor
+ DEVICE_VARIANT := v1
+ DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
+ TPLINK_BOARD_ID := EAP225-OUTDOOR-V1
+endef
+TARGET_DEVICES += tplink_eap225-outdoor-v1
+
define Device/tplink_eap225-wall-v2
$(Device/tplink-eap2x5)
SOC := qca9561
diff --git a/tools/firmware-utils/src/tplink-safeloader.c b/tools/firmware-utils/src/tplink-safeloader.c
index 2657b2c928..4389cf0346 100644
--- a/tools/firmware-utils/src/tplink-safeloader.c
+++ b/tools/firmware-utils/src/tplink-safeloader.c
@@ -1298,6 +1298,35 @@ static struct device_info boards[] = {
.last_sysupgrade_partition = "file-system"
},
+ /** Firmware layout for the EAP225-Outdoor v1 */
+ {
+ .id = "EAP225-OUTDOOR-V1",
+ .support_list =
+ "SupportList:\r\n"
+ "EAP225-Outdoor(TP-Link|UN|AC1200-D):1.0\r\n",
+ .support_trail = '\xff',
+ .soft_ver = NULL,
+ .soft_ver_compat_level = 1,
+
+ .partitions = {
+ {"fs-uboot", 0x00000, 0x20000},
+ {"partition-table", 0x20000, 0x02000},
+ {"default-mac", 0x30000, 0x01000},
+ {"support-list", 0x31000, 0x00100},
+ {"product-info", 0x31100, 0x00400},
+ {"soft-version", 0x32000, 0x00100},
+ {"firmware", 0x40000, 0xd80000},
+ {"user-config", 0xdc0000, 0x30000},
+ {"mutil-log", 0xf30000, 0x80000},
+ {"oops", 0xfb0000, 0x40000},
+ {"radio", 0xff0000, 0x10000},
+ {NULL, 0, 0}
+ },
+
+ .first_sysupgrade_partition = "os-image",
+ .last_sysupgrade_partition = "file-system"
+ },
+
/** Firmware layout for the EAP225-Wall v2 */
{
.id = "EAP225-WALL-V2",
More information about the lede-commits
mailing list