[openwrt/openwrt] ath79: Add support for OpenMesh OM2P-LC
LEDE Commits
lede-commits at lists.infradead.org
Wed Dec 30 17:32:40 EST 2020
adrian pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/eb3a5ddba0d4d0c4ab1f21ccbfbcf9aa0254bce9
commit eb3a5ddba0d4d0c4ab1f21ccbfbcf9aa0254bce9
Author: Sven Eckelmann <sven at narfation.org>
AuthorDate: Mon Nov 23 13:41:34 2020 +0100
ath79: Add support for OpenMesh OM2P-LC
Device specifications:
======================
* Qualcomm/Atheros AR9330 rev 1
* 400/400/200 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ builtin switch port 1
+ used as LAN interface
- eth1
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to
the device via
scp <filename-of-squashfs-sysupgrade>.bin root at 192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven at narfation.org>
---
package/boot/uboot-envtools/Makefile | 2 +-
package/boot/uboot-envtools/files/ath79 | 1 +
target/linux/ath79/dts/ar9330_openmesh_om2p-lc.dts | 8 ++
target/linux/ath79/dts/ar9330_openmesh_om2p.dtsi | 151 +++++++++++++++++++++
.../ath79/generic/base-files/etc/board.d/01_leds | 1 +
.../generic/base-files/lib/upgrade/platform.sh | 3 +-
target/linux/ath79/image/generic.mk | 8 ++
7 files changed, 172 insertions(+), 2 deletions(-)
diff --git a/package/boot/uboot-envtools/Makefile b/package/boot/uboot-envtools/Makefile
index 7557984595..7dcc3ef428 100644
--- a/package/boot/uboot-envtools/Makefile
+++ b/package/boot/uboot-envtools/Makefile
@@ -10,7 +10,7 @@ include $(TOPDIR)/rules.mk
PKG_NAME:=uboot-envtools
PKG_DISTNAME:=u-boot
PKG_VERSION:=2020.04
-PKG_RELEASE:=14
+PKG_RELEASE:=15
PKG_SOURCE:=$(PKG_DISTNAME)-$(PKG_VERSION).tar.bz2
PKG_SOURCE_URL:= \
diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79
index 2865501f26..70331b694a 100644
--- a/package/boot/uboot-envtools/files/ath79
+++ b/package/boot/uboot-envtools/files/ath79
@@ -90,6 +90,7 @@ openmesh,om2p-hs-v1|\
openmesh,om2p-hs-v2|\
openmesh,om2p-hs-v3|\
openmesh,om2p-hs-v4|\
+openmesh,om2p-lc|\
plasmacloud,pa300|\
plasmacloud,pa300e)
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x40000" "0x40000"
diff --git a/target/linux/ath79/dts/ar9330_openmesh_om2p-lc.dts b/target/linux/ath79/dts/ar9330_openmesh_om2p-lc.dts
new file mode 100644
index 0000000000..7383df50ab
--- /dev/null
+++ b/target/linux/ath79/dts/ar9330_openmesh_om2p-lc.dts
@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "ar9330_openmesh_om2p.dtsi"
+
+/ {
+ compatible = "openmesh,om2p-lc", "qca,ar9330";
+ model = "OpenMesh OM2P-LC";
+};
diff --git a/target/linux/ath79/dts/ar9330_openmesh_om2p.dtsi b/target/linux/ath79/dts/ar9330_openmesh_om2p.dtsi
new file mode 100644
index 0000000000..d9ca2c0f72
--- /dev/null
+++ b/target/linux/ath79/dts/ar9330_openmesh_om2p.dtsi
@@ -0,0 +1,151 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "ar9330.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ chosen {
+ /delete-property/ bootargs;
+ };
+
+ aliases {
+ serial0 = &uart;
+ led-boot = &led_power_blue;
+ led-failsafe = &led_power_blue;
+ led-running = &led_power_blue;
+ led-upgrade = &led_power_blue;
+ label-mac-device = ð1;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&switch_led_disable_pins>;
+
+ wifi_yellow {
+ label = "yellow:wifi";
+ gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+ };
+
+ led_power_blue: power_blue {
+ label = "blue:power";
+ gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ lan_blue {
+ label = "blue:lan";
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ };
+
+ wifi_green {
+ label = "green:wifi";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ wifi_red {
+ label = "red:wifi";
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ };
+
+ wan_blue {
+ label = "blue:wan";
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ watchdog {
+ compatible = "linux,wdt-gpio";
+ gpios = <&gpio 26 GPIO_ACTIVE_LOW>;
+ hw_algo = "toggle";
+ /* hw_margin_ms is actually 300s but driver limits it to 60s */
+ hw_margin_ms = <60000>;
+ always-running;
+ };
+};
+
+&uart {
+ status = "okay";
+};
+
+&spi {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ /* partitions are passed via bootloader */
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x000000 0x040000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "u-boot-env";
+ reg = <0x040000 0x040000>;
+ };
+
+ partition at 80000 {
+ label = "custom";
+ reg = <0x080000 0x140000>;
+ read-only;
+ };
+
+ partition at 1c0000 {
+ label = "inactive";
+ reg = <0x1c0000 0x700000>;
+ };
+
+ partition at 8c0000 {
+ label = "inactive2";
+ reg = <0x8c0000 0x700000>;
+ };
+
+ art: partition at fc0000 {
+ label = "ART";
+ reg = <0xfc0000 0x040000>;
+ read-only;
+ };
+ };
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ mtd-mac-address = <&art 0x6>;
+};
+
+ð1 {
+ status = "okay";
+
+ mtd-mac-address = <&art 0x0>;
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x1000>;
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index 3889969ee5..b651432dca 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -148,6 +148,7 @@ comfast,cf-ew72|\
openmesh,om2p-hs-v1|\
openmesh,om2p-hs-v2|\
openmesh,om2p-hs-v3|\
+openmesh,om2p-lc|\
telco,t1)
ucidef_set_led_switch "lan" "LAN" "blue:lan" "switch0" "0x02"
ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth1"
diff --git a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
index 9ff36f1bf5..ea3d9d6d84 100644
--- a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
@@ -54,7 +54,8 @@ platform_do_upgrade() {
openmesh,om2p-hs-v1|\
openmesh,om2p-hs-v2|\
openmesh,om2p-hs-v3|\
- openmesh,om2p-hs-v4)
+ openmesh,om2p-hs-v4|\
+ openmesh,om2p-lc)
PART_NAME="inactive"
platform_do_upgrade_openmesh "$1"
;;
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index 631cc2fd6a..6f21db78d2 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -1613,6 +1613,14 @@ define Device/openmesh_om2p-hs-v4
endef
TARGET_DEVICES += openmesh_om2p-hs-v4
+define Device/openmesh_om2p-lc
+ $(Device/openmesh_om2p-common)
+ SOC := ar9330
+ DEVICE_MODEL := OM2P-LC
+ SUPPORTED_DEVICES += om2p-lc
+endef
+TARGET_DEVICES += openmesh_om2p-lc
+
define Device/openmesh_om5p-ac-v2
SOC := qca9558
DEVICE_VENDOR := OpenMesh
More information about the lede-commits
mailing list