[openwrt/openwrt] ath79: add support for Senao Engenius EAP600
LEDE Commits
lede-commits at lists.infradead.org
Fri Dec 25 04:38:31 EST 2020
ynezz pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/6c98edaae20ac1dd0364963aadeecb022f6a80a1
commit 6c98edaae20ac1dd0364963aadeecb022f6a80a1
Author: Michael Pratt <mcpratt at pm.me>
AuthorDate: Fri Oct 9 12:28:11 2020 -0400
ath79: add support for Senao Engenius EAP600
FCC ID: A8J-EAP600
Engenius EAP600 is a wireless access point with 1 gigabit ethernet port,
dual-band wireless, external ethernet switch, 4 internal antennas
and 802.3af PoE.
Specification:
- AR9344 SOC (5 GHz, 2x2, WMAC)
- AR9382 WLAN (2.4 GHz, 2x2, PCIe on-board)
- AR8035-A switch (GbE with 802.3af PoE)
- 40 MHz reference clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16DG
- UART at H1 (populated)
- 5 LEDs, 1 button (power, eth, 2.4 GHz, 5 GHz, wps) (reset)
- 4 internal antennas
MAC addresses:
MAC addresses are labeled MAC1 and MAC2
The MAC address in flash is not on the label
The OEM software reports these MACs for the ifconfig
eth0 MAC 1 *:5e ---
phy1 MAC 2 *:5f --- (2.4 GHz)
phy0 ----- *:60 art 0x0 (5 GHz)
Installation:
2 ways to flash factory.bin from OEM:
- if you get Failsafe Mode from failed flash:
only use it to flash Original firmware from Engenius
or risk kernel loop or halt which requires serial cable
Method 1: Firmware upgrade page:
OEM webpage at 192.168.1.1
username and password "admin"
Navigate to "Upgrade Firmware" page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm and wait 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fdf0000`
wait a minute
connect to ethernet and navigate to
"192.168.1.1/index.htm"
Select the factory.bin image and upload
wait about 3 minutes
Return to OEM:
If you have a serial cable, see Serial Failsafe instructions
otherwise, uboot-env can be used to make uboot load the failsafe image
*DISCLAIMER*
The Failsafe image is unique to Engenius boards.
If the failsafe image is missing or damaged this will not work
DO NOT downgrade to ar71xx this way, it can cause kernel loop or halt
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait 3 minutes
connect to ethernet and navigate to 192.168.1.1/index.htm
select OEM firmware image from Engenius and click upgrade
Format of OEM firmware image:
The OEM software of EAP600 is a heavily modified version
of Openwrt Kamikaze. One of the many modifications
is to the sysupgrade program. Image verification is performed
simply by the successful ungzip and untar of the supplied file
and name check and header verification of the resulting contents.
To form a factory.bin that is accepted by OEM Openwrt build,
the kernel and rootfs must have specific names...
openwrt-senao-eap600-uImage-lzma.bin
openwrt-senao-eap600-root.squashfs
and begin with the respective headers (uImage, squashfs).
Then the files must be tarballed and gzipped.
The resulting binary is actually a tar.gz file in disguise.
This can be verified by using binwalk on the OEM firmware images,
ungzipping then untaring.
The OEM upgrade script is at /etc/fwupgrade.sh
Later models in the EAP series likely have a different platform
and the upgrade and image verification process differs.
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035-A switch between
the SOC and the ethernet PHY chips.
For AR934x series, the PLL register for GMAC0
can be seen in the DTSI as 0x2c.
Therefore the PLL register can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x1805002c 1`.
Unfortunately uboot did not have the best values
so they were taken from other similar DTS files.
Tested from master, all link speeds functional
Signed-off-by: Michael Pratt <mcpratt at pm.me>
---
package/boot/uboot-envtools/files/ath79 | 1 +
target/linux/ath79/dts/ar9344_engenius_eap600.dts | 45 ++++++++++++++++++++++
.../generic/base-files/etc/board.d/02_network | 1 +
.../etc/hotplug.d/firmware/10-ath9k-eeprom | 1 +
target/linux/ath79/image/generic.mk | 10 +++++
5 files changed, 58 insertions(+)
diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79
index 4cfcdd3066..8f4b8ef31e 100644
--- a/package/boot/uboot-envtools/files/ath79
+++ b/package/boot/uboot-envtools/files/ath79
@@ -24,6 +24,7 @@ arduino,yun|\
buffalo,bhr-4grv2|\
devolo,magic-2-wifi|\
engenius,eap300-v2|\
+engenius,eap600|\
engenius,ecb1200|\
engenius,ecb1750|\
engenius,ecb350-v1|\
diff --git a/target/linux/ath79/dts/ar9344_engenius_eap600.dts b/target/linux/ath79/dts/ar9344_engenius_eap600.dts
new file mode 100644
index 0000000000..c6961f636e
--- /dev/null
+++ b/target/linux/ath79/dts/ar9344_engenius_eap600.dts
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "ar9344_engenius_exx600.dtsi"
+
+/ {
+ model = "EnGenius EAP600";
+ compatible = "engenius,eap600", "qca,ar9344";
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ label = "amber:power";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ wps {
+ label = "blue:wps";
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ };
+
+ wifi5g {
+ label = "green:wifi5g";
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+ };
+};
+
+ð0 {
+ mtd-mac-address = <&art 0x0>;
+ mtd-mac-address-increment = <(-2)>;
+};
+
+&pcie {
+ wifi at 0,0,0 {
+ mtd-mac-address = <&art 0x0>;
+ };
+};
+
+&wmac {
+ mtd-mac-address = <&art 0x0>;
+ mtd-mac-address-increment = <(-1)>;
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index a3b5d45ad2..355ea25b4d 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -29,6 +29,7 @@ ath79_setup_interfaces()
dlink,dap-1365-a1|\
dlink,dir-505|\
engenius,eap300-v2|\
+ engenius,eap600|\
engenius,ecb1200|\
engenius,ecb1750|\
engenius,ecb350-v1|\
diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index 867a1dac44..553db59231 100644
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -88,6 +88,7 @@ case "$FIRMWARE" in
caldata_extract "art" 0x5000 0x440
ath9k_patch_mac $(macaddr_add $(mtd_get_mac_text "mac" 0x18) 1)
;;
+ engenius,eap600|\
engenius,ecb600|\
mercury,mw4530r-v1|\
ocedo,raccoon|\
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index 064177fcaf..8f9e7159d1 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -965,6 +965,16 @@ define Device/engenius_eap300-v2
endef
TARGET_DEVICES += engenius_eap300-v2
+define Device/engenius_eap600
+ $(Device/engenius_loader_okli)
+ SOC := ar9344
+ DEVICE_MODEL := EAP600
+ IMAGE_SIZE := 12032k
+ LOADER_FLASH_OFFS := 0x230000
+ ENGENIUS_IMGNAME := senao-eap600
+endef
+TARGET_DEVICES += engenius_eap600
+
define Device/engenius_ecb1200
SOC := qca9557
DEVICE_VENDOR := EnGenius
More information about the lede-commits
mailing list