[openwrt/openwrt] ipq40xx: add support for Plasma Cloud PA2200
LEDE Commits
lede-commits at lists.infradead.org
Tue Dec 22 13:13:49 EST 2020
ynezz pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/4871fd2616acb03fefe69b068955dba36eb00770
commit 4871fd2616acb03fefe69b068955dba36eb00770
Author: Marek Lindner <marek.lindner at kaiwoo.ai>
AuthorDate: Fri Dec 14 23:46:53 2018 +0800
ipq40xx: add support for Plasma Cloud PA2200
Device specifications:
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200
* GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE
* GPIO-LEDs for power (orange) and status (blue)
* 1x GPIO-button (reset)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy at mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ used as LAN interface
- phy at mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 802.3at POE+
+ used as WAN interface
* 12V 2A DC
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Marek Lindner <marek.lindner at kaiwoo.ai>
[sven at narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven at narfation.org>
---
package/boot/uboot-envtools/files/ipq40xx | 3 +-
package/firmware/ipq-wifi/Makefile | 2 +
.../ipq-wifi/board-plasmacloud_pa2200.ipq4019 | Bin 0 -> 24324 bytes
.../ipq-wifi/board-plasmacloud_pa2200.qca9888 | Bin 0 -> 12172 bytes
scripts/om-fwupgradecfg-gen.sh | 4 +-
.../ipq40xx/base-files/etc/board.d/02_network | 3 +-
.../etc/hotplug.d/firmware/11-ath10k-caldata | 5 +-
.../base-files/lib/upgrade/dualboot_datachk.sh | 1 +
.../ipq40xx/base-files/lib/upgrade/platform.sh | 3 +-
.../arch/arm/boot/dts/qcom-ipq4019-pa2200.dts | 210 +++++++++++++++++++++
target/linux/ipq40xx/image/Makefile | 16 ++
.../patches-5.4/901-arm-boot-add-dts-files.patch | 3 +-
12 files changed, 243 insertions(+), 7 deletions(-)
diff --git a/package/boot/uboot-envtools/files/ipq40xx b/package/boot/uboot-envtools/files/ipq40xx
index 9252c0ffac..bcb4c5c962 100644
--- a/package/boot/uboot-envtools/files/ipq40xx
+++ b/package/boot/uboot-envtools/files/ipq40xx
@@ -37,7 +37,8 @@ glinet,gl-b1300 |\
luma,wrtq-329acn |\
openmesh,a42 |\
openmesh,a62 |\
-plasmacloud,pa1200)
+plasmacloud,pa1200 |\
+plasmacloud,pa2200)
ubootenv_add_uci_config "/dev/mtd5" "0x0" "0x10000" "0x10000"
;;
buffalo,wtr-m2133hp)
diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile
index e26269a710..dfb9e0feb3 100644
--- a/package/firmware/ipq-wifi/Makefile
+++ b/package/firmware/ipq-wifi/Makefile
@@ -43,6 +43,7 @@ ALLWIFIBOARDS:= \
luma_wrtq-329acn \
mobipromo_cm520-79f \
plasmacloud_pa1200 \
+ plasmacloud_pa2200 \
qxwlan_e2600ac
ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
@@ -122,6 +123,7 @@ $(eval $(call generate-ipq-wifi-package,linksys_mr8300-v0,Linksys MR8300))
$(eval $(call generate-ipq-wifi-package,luma_wrtq-329acn,Luma WRTQ-329ACN))
$(eval $(call generate-ipq-wifi-package,mobipromo_cm520-79f,MobiPromo CM520-79F))
$(eval $(call generate-ipq-wifi-package,plasmacloud_pa1200,Plasma Cloud PA1200))
+$(eval $(call generate-ipq-wifi-package,plasmacloud_pa2200,Plasma Cloud PA2200))
$(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,Qxwlan E2600AC))
$(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))
diff --git a/package/firmware/ipq-wifi/board-plasmacloud_pa2200.ipq4019 b/package/firmware/ipq-wifi/board-plasmacloud_pa2200.ipq4019
new file mode 100644
index 0000000000..d1db0f5f4b
Binary files /dev/null and b/package/firmware/ipq-wifi/board-plasmacloud_pa2200.ipq4019 differ
diff --git a/package/firmware/ipq-wifi/board-plasmacloud_pa2200.qca9888 b/package/firmware/ipq-wifi/board-plasmacloud_pa2200.qca9888
new file mode 100644
index 0000000000..6c3f083eb2
Binary files /dev/null and b/package/firmware/ipq-wifi/board-plasmacloud_pa2200.qca9888 differ
diff --git a/scripts/om-fwupgradecfg-gen.sh b/scripts/om-fwupgradecfg-gen.sh
index c5dcfb0018..bf7c047c5b 100755
--- a/scripts/om-fwupgradecfg-gen.sh
+++ b/scripts/om-fwupgradecfg-gen.sh
@@ -7,7 +7,7 @@
#
usage() {
- echo "Usage: $0 <OM2P|OM5P|OM5PAC|MR600|MR900|MR1750|A60|A42|A62|PA300|PA1200> <out file path> <kernel path> <rootfs path>"
+ echo "Usage: $0 <OM2P|OM5P|OM5PAC|MR600|MR900|MR1750|A60|A42|A62|PA300|PA1200|PA2200> <out file path> <kernel path> <rootfs path>"
rm -f $CFG_OUT
exit 1
}
@@ -39,7 +39,7 @@ case $CE_TYPE in
SIZE_FACTOR=1024
SIZE_FORMAT="0x%08x"
;;
- A62)
+ A62|PA2200)
MAX_PART_SIZE=15552
KERNEL_FLASH_ADDR=0x1a0000
SIZE_FACTOR=1024
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index b9e79c3b68..4361b7c395 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -18,7 +18,8 @@ ipq40xx_setup_interfaces()
engenius,emr3500|\
engenius,ens620ext|\
luma,wrtq-329acn|\
- plasmacloud,pa1200)
+ plasmacloud,pa1200|\
+ plasmacloud,pa2200)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
;;
aruba,ap-303|\
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index ade0d74341..e50732586a 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -36,7 +36,8 @@ case "$FIRMWARE" in
ath10k_patch_mac $(mtd_get_mac_binary ORGDATA 0x32)
;;
engenius,eap2200 |\
- openmesh,a62)
+ openmesh,a62 |\
+ plasmacloud,pa2200)
caldata_extract "0:ART" 0x9000 0x2f20
;;
linksys,ea8300 |\
@@ -102,6 +103,7 @@ case "$FIRMWARE" in
openmesh,a42 |\
openmesh,a62 |\
plasmacloud,pa1200 |\
+ plasmacloud,pa2200 |\
qxwlan,e2600ac-c1 |\
qxwlan,e2600ac-c2 |\
unielec,u4019-32m)
@@ -200,6 +202,7 @@ case "$FIRMWARE" in
openmesh,a42 |\
openmesh,a62 |\
plasmacloud,pa1200 |\
+ plasmacloud,pa2200 |\
qxwlan,e2600ac-c1 |\
qxwlan,e2600ac-c2 |\
unielec,u4019-32m)
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/dualboot_datachk.sh b/target/linux/ipq40xx/base-files/lib/upgrade/dualboot_datachk.sh
index 60886071c9..81418fe0ba 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/dualboot_datachk.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/dualboot_datachk.sh
@@ -48,6 +48,7 @@ platform_do_upgrade_dualboot_datachk() {
openmesh,a42)
primary_kernel_mtd=8
;;
+ plasmacloud,pa2200|\
openmesh,a62)
primary_kernel_mtd=10
;;
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
index 22e9ffe114..e43225cbb2 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
@@ -112,7 +112,8 @@ platform_do_upgrade() {
;;
openmesh,a42 |\
openmesh,a62 |\
- plasmacloud,pa1200)
+ plasmacloud,pa1200 |\
+ plasmacloud,pa2200)
PART_NAME="inactive"
platform_do_upgrade_dualboot_datachk "$1"
;;
diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-pa2200.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-pa2200.dts
new file mode 100644
index 0000000000..2d0655114b
--- /dev/null
+++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-pa2200.dts
@@ -0,0 +1,210 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/* Copyright (c) 2017-2020, Sven Eckelmann <sven at narfation.org>
+ * Copyright (c) 2018, Marek Lindner <marek.lindner at kaiwoo.ai>
+ */
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "Plasma Cloud PA2200";
+ compatible = "plasmacloud,pa2200";
+
+ soc {
+ rng at 22000 {
+ status = "okay";
+ };
+
+ mdio at 90000 {
+ status = "okay";
+ };
+
+ ess-psgmii at 98000 {
+ status = "okay";
+ };
+
+ tcsr at 1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ ess_tcsr at 1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr at 1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ crypto at 8e3a000 {
+ status = "okay";
+ };
+
+ watchdog at b017000 {
+ status = "okay";
+ };
+
+ ess-switch at c000000 {
+ switch_lan_bmp = <0x10>;
+ switch_wan_bmp = <0x20>;
+
+ status = "okay";
+ };
+
+ edma at c080000 {
+ status = "okay";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART >;
+ };
+ };
+
+ aliases {
+ led-boot = &led_power_orange;
+ led-failsafe = &led_status_blue;
+ led-running = &led_power_orange;
+ led-upgrade = &led_status_blue;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power_orange: power_orange {
+ label = "orange:power";
+ gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
+ };
+
+ 2g_blue {
+ label = "blue:2g";
+ gpios = <&tlmm 46 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+
+ 2g_green {
+ label = "green:5g1";
+ gpios = <&tlmm 47 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ 5g2_green {
+ label = "green:5g2";
+ gpios = <&tlmm 48 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy2tpt";
+ };
+
+ led_status_blue: status_blue {
+ label = "blue:status";
+ gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&tlmm {
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pin {
+ function = "blsp_spi0";
+ pins = "gpio13", "gpio14", "gpio15";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pin_cs {
+ function = "gpio";
+ pins = "gpio12";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+
+ flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+ /* partitions are passed via bootloader */
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&gmac0 {
+ qcom,phy_mdio_addr = <3>;
+ qcom,poll_required = <1>;
+ qcom,forced_speed = <1000>;
+ qcom,forced_duplex = <1>;
+ vlan_tag = <1 0x10>;
+};
+
+&pcie0 {
+ status = "okay";
+ perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+ wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+
+ bridge at 0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi2: wifi at 1,0 {
+ compatible = "qcom,ath10k";
+ status = "okay";
+ reg = <0x00010000 0 0 0 0>;
+ qcom,ath10k-calibration-variant = "PlasmaCloud-PA2200";
+ ieee80211-freq-limit = <5170000 5350000>;
+ };
+ };
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "PlasmaCloud-PA2200";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "PlasmaCloud-PA2200";
+ ieee80211-freq-limit = <5470000 5875000>;
+};
diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile
index b0fde22813..86bf5a2ccb 100644
--- a/target/linux/ipq40xx/image/Makefile
+++ b/target/linux/ipq40xx/image/Makefile
@@ -664,6 +664,22 @@ define Device/plasmacloud_pa1200
endef
TARGET_DEVICES += plasmacloud_pa1200
+define Device/plasmacloud_pa2200
+ $(call Device/FitImageLzma)
+ DEVICE_VENDOR := Plasma Cloud
+ DEVICE_MODEL := PA2200
+ SOC := qcom-ipq4019
+ DEVICE_DTS_CONFIG := config at pc.pa2200
+ BLOCKSIZE := 64k
+ KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
+ IMAGE_SIZE := 15552k
+ IMAGES += factory.bin
+ IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=PA2200
+ IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
+ DEVICE_PACKAGES := ath10k-firmware-qca9888-ct ipq-wifi-plasmacloud-pa2200 uboot-envtools
+endef
+TARGET_DEVICES += plasmacloud_pa2200
+
define Device/qcom_ap-dk01.1-c1
DEVICE_VENDOR := Qualcomm Atheros
DEVICE_MODEL := AP-DK01.1
diff --git a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
index 8d725ebf9e..c4502aa3f7 100644
--- a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john at phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -837,11 +837,55 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -837,11 +837,56 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
@@ -52,6 +52,7 @@ Signed-off-by: John Crispin <john at phrozen.org>
+ qcom-ipq4019-e2600ac-c1.dtb \
+ qcom-ipq4019-e2600ac-c2.dtb \
+ qcom-ipq4019-habanero-dvk.dtb \
++ qcom-ipq4019-pa2200.dtb \
+ qcom-ipq4019-rtl30vw.dtb \
+ qcom-ipq4019-u4019-32m.dtb \
+ qcom-ipq4019-wpj419.dtb \
More information about the lede-commits
mailing list