[openwrt/openwrt] ath79: add support for Belkin F9J1108v2 (AC1750 DB Wi-Fi)
LEDE Commits
lede-commits at lists.infradead.org
Mon Dec 7 08:46:10 EST 2020
adrian pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/b9971db7c365c0145faf1db2e78ee48cee4b643d
commit b9971db7c365c0145faf1db2e78ee48cee4b643d
Author: Damien Mascord <tusker at tusker.org>
AuthorDate: Mon Dec 7 13:01:38 2020 +1100
ath79: add support for Belkin F9J1108v2 (AC1750 DB Wi-Fi)
This device is the non-US build of the F9K1115 v2, with a different
firmware magic.
Specifications:
SoC: QCA9558
CPU: 720 MHz
Flash: 16 MiB NOR
RAM: 128 MiB
WiFi 2.4 GHz: QCA9558-AT4A 3x3 MIMO 802.11b/g/n
WiFi 5 GHz: QCA9880-2R4E 3x3 MIMO 802.11a/n/ac
Ethernet: 4x LAN and 1x WAN (all 1gbps)
USB: 1 x USB 2.0 (lower), 1 x USB 3.0 (upper)
MAC addresses based on OEM firmware:
Interface Address Location
--------- ------- --------
lan *:5A sometimes in 0x6
wan *:5B 0x0
2.4Ghz *:5A 0x1002
5Ghz As per mini PCIe EEPROM
Flashing instructions:
The factory.bin can be flashed via the Belkin web UI or via the uboot
http upgrade page.
Once the factory.bin has been written, sysupgrade.bin will work as usual.
Signed-off-by: Damien Mascord <tusker at tusker.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
[wrap commit message/code, adjust label-mac-device, whitespace fixes,
merge block in 02_network]
Signed-off-by: Adrian Schmutzler <freifunk at adrianschmutzler.de>
---
.../linux/ath79/dts/qca9558_belkin_f9j1108-v2.dts | 229 +++++++++++++++++++++
.../generic/base-files/etc/board.d/02_network | 17 +-
target/linux/ath79/image/generic.mk | 39 ++++
3 files changed, 277 insertions(+), 8 deletions(-)
diff --git a/target/linux/ath79/dts/qca9558_belkin_f9j1108-v2.dts b/target/linux/ath79/dts/qca9558_belkin_f9j1108-v2.dts
new file mode 100644
index 0000000000..0bd3af98db
--- /dev/null
+++ b/target/linux/ath79/dts/qca9558_belkin_f9j1108-v2.dts
@@ -0,0 +1,229 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca955x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Belkin F9J1108 v2 (AC1750 DB Wi-Fi)";
+ compatible = "belkin,f9j1108-v2", "qca,qca9558";
+
+ aliases {
+ led-boot = &led_system;
+ led-failsafe = &led_system;
+ led-running = &led_system;
+ led-upgrade = &led_system;
+ label-mac-device = ð1;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ usb {
+ label = "green:usb2";
+ gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+ trigger-sources = <&hub_port0>;
+ linux,default-trigger = "usbport";
+ };
+
+ status {
+ label = "amber:status";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ };
+
+ wps-amber {
+ label = "amber:wps";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ };
+
+ wps-blue {
+ label = "blue:wps";
+ gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+ };
+
+ led_system: system {
+ label = "blue:system";
+ gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-export {
+ compatible = "gpio-export";
+ #size-cells = <0>;
+
+ usb2_power {
+ gpio-export,name = "usb2:power";
+ gpio-export,output = <1>;
+ gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ wps {
+ label = "WPS button";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+
+ reset {
+ label = "Reset button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+ };
+
+ virtual_flash {
+ compatible = "mtd-concat";
+
+ devices = <&fwpart1 &fwpart2>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ compatible = "openwrt,okli";
+ label = "firmware";
+ reg = <0x0 0x0>;
+ };
+ };
+ };
+};
+
+&pcie1 {
+ status = "okay";
+};
+
+&uart {
+ status = "okay";
+};
+
+&usb_phy0 {
+ status = "okay";
+};
+
+&usb0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ hub_port0: port at 1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+};
+
+&spi {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <80000000>;
+ m25p,fast-read;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ uboot: partition at 0 {
+ label = "u-boot";
+ reg = <0x000000 0x040000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "u-boot-env";
+ reg = <0x040000 0x010000>;
+ };
+
+ fwpart1: partition at 50000 {
+ label = "fwpart1";
+ reg = <0x050000 0xe20000>;
+ };
+
+ partition at e70000 {
+ label = "loader";
+ reg = <0xe70000 0x10000>;
+ read-only;
+ };
+
+ fwpart2: partition at e80000 {
+ label = "fwpart2";
+ reg = <0xe80000 0x170000>;
+ };
+
+ art: partition at ff0000 {
+ label = "art";
+ reg = <0xff0000 0x010000>;
+ };
+ };
+ };
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy0: ethernet-phy at 0 {
+ reg = <0>;
+
+ qca,ar8327-initvals = <
+ 0x04 0x00080080 /* PORT0 PAD MODE CTRL */
+ 0x0c 0x07600000 /* PORT6 PAD MODE CTRL */
+ 0x50 0xc737c737 /* LED_CTRL0 */
+ 0x54 0x00000000 /* LED_CTRL1 */
+ 0x58 0x00000000 /* LED_CTRL2 */
+ 0x5c 0x0030c300 /* LED_CTRL3 */
+ 0x7c 0x0000007e /* PORT0_STATUS */
+ 0x94 0x0000007e /* PORT6 STATUS */
+ >;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ mtd-mac-address = <&art 0x0>;
+ phy-handle = <&phy0>;
+ pll-data = <0xa6000000 0x00000101 0x00001616>;
+
+ gmac-config {
+ device = <&gmac>;
+ rgmii-enabled = <1>;
+ };
+};
+
+ð1 {
+ status = "okay";
+
+ mtd-mac-address = <&art 0x0>;
+ mtd-mac-address-increment = <(-1)>;
+ pll-data = <0x03000101 0x00000101 0x00001616>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&pcie0 {
+ status = "okay";
+
+ wifi at 0,0 {
+ compatible = "qcom,ath10k";
+ reg = <0 0 0 0 0>;
+ };
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x1000>;
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index 149f7b1141..987b405431 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -100,6 +100,15 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0 at eth0" "1:lan:1" "2:lan:4" "3:lan:3" "4:lan:2"
;;
+ belkin,f9j1108-v2|\
+ tplink,archer-c5-v1|\
+ tplink,archer-c7-v1|\
+ tplink,archer-c7-v2|\
+ tplink,tl-wdr4900-v2|\
+ tplink,tl-wdr7500-v3)
+ ucidef_add_switch "switch0" \
+ "0 at eth1" "2:lan" "3:lan" "4:lan" "5:lan" "6 at eth0" "1:wan"
+ ;;
buffalo,bhr-4grv|\
buffalo,wzr-hp-g450h)
ucidef_add_switch "switch0" \
@@ -308,14 +317,6 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0 at eth0" "2:lan:3" "3:lan:2" "4:lan:1"
;;
- tplink,archer-c5-v1|\
- tplink,archer-c7-v1|\
- tplink,archer-c7-v2|\
- tplink,tl-wdr4900-v2|\
- tplink,tl-wdr7500-v3)
- ucidef_add_switch "switch0" \
- "0 at eth1" "2:lan" "3:lan" "4:lan" "5:lan" "6 at eth0" "1:wan"
- ;;
tplink,archer-d50-v1)
ucidef_add_switch "switch0" \
"0 at eth0" "2:lan:3" "3:lan:2" "4:lan:1" "1:wan"
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index 614f9ff0b2..d5fbd89c26 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -50,6 +50,24 @@ define Build/cybertan-trx
-rm $@-empty.bin
endef
+define Build/edimax-headers
+ $(eval edimax_magic=$(word 1,$(1)))
+ $(eval edimax_model=$(word 2,$(1)))
+
+ $(STAGING_DIR_HOST)/bin/edimax_fw_header -M $(edimax_magic) -m $(edimax_model)\
+ -v $(VERSION_DIST)$(firstword $(subst +, , $(firstword $(subst -, ,$(REVISION))))) \
+ -n "uImage" \
+ -i $(KDIR)/loader-$(DEVICE_NAME).uImage \
+ -o $@.uImage
+ $(STAGING_DIR_HOST)/bin/edimax_fw_header -M $(edimax_magic) -m $(edimax_model)\
+ -v $(VERSION_DIST)$(firstword $(subst +, , $(firstword $(subst -, ,$(REVISION))))) \
+ -n "rootfs" \
+ -i $@ \
+ -o $@.rootfs
+ cat $@.uImage $@.rootfs > $@
+ rm -rf $@.uImage $@.rootfs
+endef
+
# This needs to make /tmp/_sys/sysupgrade.tgz an empty file prior to
# sysupgrade, as otherwise it will implant the old configuration from
# OEM firmware when writing rootfs from factory.bin
@@ -363,6 +381,27 @@ define Device/avm_fritzdvbc
endef
TARGET_DEVICES += avm_fritzdvbc
+define Device/belkin_f9j1108-v2
+ SOC := qca9558
+ DEVICE_VENDOR := Belkin
+ DEVICE_MODEL := F9J1108 v2 (AC1750 DB Wi-Fi)
+ IMAGE_SIZE := 14464k
+ DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct kmod-usb2 \
+ kmod-usb3 kmod-usb-ledtrig-usbport
+ LOADER_TYPE := bin
+ LOADER_FLASH_OFFS := 0x50000
+ COMPILE := loader-$(1).bin loader-$(1).uImage
+ COMPILE/loader-$(1).bin := loader-okli-compile
+ COMPILE/loader-$(1).uImage := append-loader-okli $(1) | pad-to 64k | \
+ lzma | uImage lzma
+ KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49
+ IMAGES += factory.bin
+ IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
+ append-rootfs | pad-rootfs | check-size | \
+ edimax-headers F9J1108v1 BR-6679BAC | pad-to $$$$(BLOCKSIZE)
+endef
+TARGET_DEVICES += belkin_f9j1108-v2
+
define Device/buffalo_bhr-4grv
$(Device/buffalo_common)
SOC := ar7242
More information about the lede-commits
mailing list