[openwrt/openwrt] ramips: correct WizFi630S pin mappings

[LEDE Commits]

adrian pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/d0b229f553a814b22c16976e40a197f892c0c0df

commit d0b229f553a814b22c16976e40a197f892c0c0df
Author: Tobias Welz <tw at wiznet.eu>
AuthorDate: Tue Aug 4 17:55:40 2020 +0200

    ramips: correct WizFi630S pin mappings
    
    WizFi630S had some pins changed in the release version of the board.
    The run led, wps button and a slide switch where affected.
    This patch is correcting this.
    i2c is removed as it is sharing a pin with the run (system) led.
    uart2 is enabled as it is also enabled in the OEM firmware.
    
    Signed-off-by: Tobias Welz <tw at wiznet.eu>
---
 .../linux/ramips/dts/mt7628an_wiznet_wizfi630s.dts | 34 +++++-----------------
 1 file changed, 8 insertions(+), 26 deletions(-)

diff --git a/target/linux/ramips/dts/mt7628an_wiznet_wizfi630s.dts b/target/linux/ramips/dts/mt7628an_wiznet_wizfi630s.dts
index 41634c6002..684a70cffe 100644
--- a/target/linux/ramips/dts/mt7628an_wiznet_wizfi630s.dts
+++ b/target/linux/ramips/dts/mt7628an_wiznet_wizfi630s.dts
@@ -28,7 +28,7 @@
 
 		led_run: run {
 			label = "wizfi630s:green:run";
-			gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
 		};
 
 		ledwps {
@@ -61,47 +61,29 @@
 
 		wps {
 			label = "wps";
-			gpios = <&gpio 32 GPIO_ACTIVE_HIGH>;
+			gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WPS_BUTTON>;
 		};
 
 		scm1 {
 			label = "SCM1";
-			gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_1>;
+			linux,input-type = <EV_SW>;
 		};
 
 		scm2 {
 			label = "SCM2";
 			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_2>;
+			linux,input-type = <EV_SW>;
 		};
 	};
 };
 
 &state_default {
 	gpio {
-		groups = "gpio";
-		function = "gpio";
-	};
-
-	i2s {
-		groups = "i2s";
-		function = "gpio";
-	};
-
-	wdt {
-		groups = "wdt";
-		function = "gpio";
-	};
-
-	i2c {
-		groups = "i2c";
-		function = "gpio";
-	};
-
-	refclk {
-		groups = "refclk";
+		groups = "gpio", "i2s", "i2c", "wdt", "refclk", "p1led_an", "p2led_an";
 		function = "gpio";
 	};
 };
@@ -150,11 +132,11 @@
 	};
 };
 
-&i2c {
+&uart1 {
 	status = "okay";
 };
 
-&uart1 {
+&uart2 {
 	status = "okay";
 };