[openwrt/openwrt] gemini: add 4.14 support
LEDE Commits
lede-commits at lists.infradead.org
Fri May 4 23:26:20 PDT 2018
blogic pushed a commit to openwrt/openwrt.git, branch master:
https://git.lede-project.org/4f74957584cd50786d1d33a3f26867b06a58510f
commit 4f74957584cd50786d1d33a3f26867b06a58510f
Author: Roman Yeryomin <roman at advem.lv>
AuthorDate: Sun Apr 29 17:38:07 2018 +0300
gemini: add 4.14 support
This adds the patches to get fairly complete Gemini support
using kernel v4.14. It is mainly a backport of patches from
kernel v4.16 with omissions of things like graphics that require
substantial changes and will be better handled once we move
to the v4.16 kernel proper.
On top of this are some WIP patches for USB support.
Tested on Raidsonic NAS4220B and D-link DNS-313.
ChangeLog v4->v5:
- Fix ethernet single gmac usecase
- Fix USB reset (patch from Hans)
- Fix Raidsonic ethernet skew delay
- Fix kernel config (bridge, squashfs, jffs2, usb)
- Disable second usb port on Raidsonic board until fotg210_hcd is fixed
ChangeLog v3->v4:
- Make sure to use tabs rather than spaces in base-files.
- Use the dns313 image tool from the firmware-utils.
- Break out the addition of the v4.14 patches and the removal
of the v4.4 patches to separate (big) patches.
ChangeLog v2->v3:
- Update the kernel config as indicated by Hauke Martens:
- Regenerate again after rebasing using kernel_oldconfig
dropping a few optimization settings that are now generic
- Drop CFG80211 stuff (module)
- Drop CIFS stuff (module)
- Drop MAC80211 (module)
- Drop wireless drivers (module)
- Enabled OverlayFS
- Added proper DNS-313 boot image generation with the special
file header tool.
- Disable CMA in the kernel
- Enable LZMA compression of the kernel
- Consequently name the nas4220b images nas4220b
- Update preinit MAC detection script to handle also DNS-313
- Add board.d/03_hdparm to set the disk to spin down after
1 minute by default, if we have the hdparm tool installed
ChangeLog v1->v2:
- Processed config through kernel_oldconfig
- Processed patches through make target/linux/{clean,refresh} V=99
Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
Signed-off-by: Roman Yeryomin <roman at advem.lv>
---
target/linux/gemini/config-4.14 | 576 +++
.../0001-cache-patch-from-OpenWRT.patch | 50 +
...0002-pinctrl-gemini-Add-missing-functions.patch | 33 +
...ARM-dts-Add-TVE200-to-the-Gemini-SoC-DTSI.patch | 51 +
...rl-Add-skew-delay-pin-config-and-bindings.patch | 73 +
...0005-pinctrl-gemini-Use-generic-DT-parser.patch | 112 +
...-gemini-Implement-clock-skew-delay-config.patch | 280 ++
.../0007-pinctrl-gemini-Fix-GMAC-groups.patch | 186 +
...nctrl-gemini-Fix-missing-pad-descriptions.patch | 27 +
...inctrl-gemini-Add-two-missing-GPIO-groups.patch | 25 +
...0-pinctrl-gemini-Fix-usage-of-3512-groups.patch | 25 +
...trl-gemini-Support-drive-strength-setting.patch | 198 ++
...d-ethernet-PHYs-to-the-a-bunch-of-Geminis.patch | 113 +
...s-Add-basic-devicetree-for-D-Link-DNS-313.patch | 272 ++
...RM-dts-Flags-D-Link-DIR-685-I2C-bus-gpios.patch | 27 +
...0015-ARM-dts-Add-PCI-to-WBD111-and-WBD222.patch | 74 +
...-Add-TVE-TVC-and-ILI9322-panel-to-DIR-685.patch | 113 +
...tchdog-gemini-ftwdt010-rename-DT-bindings.patch | 88 +
...gemini-ftwdt010-rename-driver-and-symbols.patch | 527 +++
...watchdog-ftwdt010-Make-interrupt-optional.patch | 93 +
.../0020-soc-Add-SoC-driver-for-Gemini.patch | 113 +
...t-Add-DT-bindings-for-the-Gemini-ethernet.patch | 119 +
...t-Add-a-driver-for-Gemini-gigabit-etherne.patch | 3661 ++++++++++++++++++++
...23-ARM-dts-Add-ethernet-to-the-Gemini-SoC.patch | 74 +
.../0024-net-gemini-Depend-on-HAS_IOMEM.patch | 30 +
...-dts-Set-D-Link-DNS-313-SATA-to-muxmode-0.patch | 36 +
...r-gemini-poweroff-Avoid-spurious-poweroff.patch | 80 +
...sb-host-add-DT-bindings-for-faraday-fotg2.patch | 65 +
...28-usb-host-fotg2-add-device-tree-probing.patch | 61 +
...usb-host-fotg2-add-silicon-clock-handling.patch | 99 +
...b-host-fotg2-add-Gemini-specific-handling.patch | 131 +
...RM-dts-Add-the-FOTG210-USB-host-to-Gemini.patch | 178 +
...b-host-fotg2-restart-hcd-after-port-reset.patch | 31 +
...emini-add-openwrt-partitions-for-nas4220b.patch | 17 +
...-arm-dts-gemini-fix-ethernet-for-nas4220b.patch | 69 +
...rm-dts-gemini-add-second-ata-for-nas4220b.patch | 13 +
...dts-gemini-disable-usb-port-1-until-fixed.patch | 11 +
...ina-fix-uninitialized-struct-member-usage.patch | 23 +
38 files changed, 7754 insertions(+)
diff --git a/target/linux/gemini/config-4.14 b/target/linux/gemini/config-4.14
new file mode 100644
index 0000000..6cadc83
--- /dev/null
+++ b/target/linux/gemini/config-4.14
@@ -0,0 +1,576 @@
+CONFIG_ALIGNMENT_TRAP=y
+CONFIG_AMBA_PL08X=y
+CONFIG_ARCH_CLOCKSOURCE_DATA=y
+CONFIG_ARCH_GEMINI=y
+CONFIG_ARCH_HAS_DEBUG_VIRTUAL=y
+CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
+CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y
+CONFIG_ARCH_HAS_RESET_CONTROLLER=y
+CONFIG_ARCH_HAS_SET_MEMORY=y
+CONFIG_ARCH_HAS_SG_CHAIN=y
+CONFIG_ARCH_HAS_STRICT_KERNEL_RWX=y
+CONFIG_ARCH_HAS_STRICT_MODULE_RWX=y
+CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
+CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
+# CONFIG_ARCH_MOXART is not set
+CONFIG_ARCH_MULTIPLATFORM=y
+# CONFIG_ARCH_MULTI_CPU_AUTO is not set
+CONFIG_ARCH_MULTI_V4=y
+# CONFIG_ARCH_MULTI_V4T is not set
+CONFIG_ARCH_MULTI_V4_V5=y
+# CONFIG_ARCH_MULTI_V5 is not set
+CONFIG_ARCH_NR_GPIO=0
+CONFIG_ARCH_OPTIONAL_KERNEL_RWX=y
+# CONFIG_ARCH_OPTIONAL_KERNEL_RWX_DEFAULT is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
+CONFIG_ARCH_SUPPORTS_UPROBES=y
+CONFIG_ARCH_USE_BUILTIN_BSWAP=y
+CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y
+# CONFIG_ARCH_WANTS_THP_SWAP is not set
+CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
+CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
+CONFIG_ARM=y
+CONFIG_ARM_AMBA=y
+CONFIG_ARM_APPENDED_DTB=y
+# CONFIG_ARM_ATAG_DTB_COMPAT is not set
+CONFIG_ARM_HAS_SG_CHAIN=y
+CONFIG_ARM_L1_CACHE_SHIFT=5
+CONFIG_ARM_PATCH_PHYS_VIRT=y
+# CONFIG_ARM_SMMU is not set
+# CONFIG_ARM_SP805_WATCHDOG is not set
+CONFIG_ARM_UNWIND=y
+CONFIG_ATA=y
+CONFIG_ATAGS=y
+CONFIG_ATA_VERBOSE_ERROR=y
+CONFIG_AUTO_ZRELADDR=y
+CONFIG_BINFMT_MISC=y
+# CONFIG_BLK_CGROUP is not set
+CONFIG_BLK_DEBUG_FS=y
+CONFIG_BLK_DEV_BSG=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=16384
+CONFIG_BLK_DEV_SD=y
+CONFIG_BLK_MQ_PCI=y
+CONFIG_BLK_SCSI_REQUEST=y
+CONFIG_BOUNCE=y
+# CONFIG_BPF_SYSCALL is not set
+CONFIG_BSD_PROCESS_ACCT=y
+# CONFIG_CACHE_L2X0 is not set
+CONFIG_CGROUPS=y
+# CONFIG_CGROUP_CPUACCT is not set
+# CONFIG_CGROUP_DEVICE is not set
+# CONFIG_CGROUP_FREEZER is not set
+# CONFIG_CGROUP_PIDS is not set
+# CONFIG_CGROUP_SCHED is not set
+CONFIG_CLKDEV_LOOKUP=y
+CONFIG_CLKSRC_MMIO=y
+CONFIG_CLONE_BACKWARDS=y
+CONFIG_CMDLINE="console=ttyS0,19200n8"
+CONFIG_CMDLINE_FORCE=y
+CONFIG_COMMON_CLK=y
+CONFIG_COMMON_CLK_GEMINI=y
+CONFIG_COMPACTION=y
+CONFIG_COMPAT_BRK=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_COREDUMP=y
+CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS=y
+CONFIG_CPU_32v4=y
+CONFIG_CPU_ABRT_EV4=y
+# CONFIG_CPU_BPREDICT_DISABLE is not set
+CONFIG_CPU_CACHE_FA=y
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_COPY_FA=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+# CONFIG_CPU_DCACHE_WRITETHROUGH is not set
+CONFIG_CPU_FA526=y
+# CONFIG_CPU_ICACHE_DISABLE is not set
+CONFIG_CPU_NO_EFFICIENT_FFS=y
+CONFIG_CPU_PABRT_LEGACY=y
+CONFIG_CPU_TLB_FA=y
+CONFIG_CPU_USE_DOMAINS=y
+CONFIG_CRASH_CORE=y
+CONFIG_CRC16=y
+# CONFIG_CRC32_SARWATE is not set
+CONFIG_CRC32_SLICEBY8=y
+CONFIG_CRC_CCITT=y
+CONFIG_CRC_ITU_T=y
+CONFIG_CROSS_MEMORY_ATTACH=y
+CONFIG_CRYPTO_AEAD=y
+CONFIG_CRYPTO_AEAD2=y
+CONFIG_CRYPTO_CCM=y
+CONFIG_CRYPTO_CMAC=y
+CONFIG_CRYPTO_CRC32C=y
+CONFIG_CRYPTO_CTR=y
+CONFIG_CRYPTO_DES=y
+CONFIG_CRYPTO_DRBG=y
+CONFIG_CRYPTO_DRBG_HMAC=y
+CONFIG_CRYPTO_DRBG_MENU=y
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_ECHAINIV=y
+CONFIG_CRYPTO_GCM=y
+CONFIG_CRYPTO_GF128MUL=y
+CONFIG_CRYPTO_GHASH=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_HW=y
+CONFIG_CRYPTO_JITTERENTROPY=y
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_MANAGER2=y
+CONFIG_CRYPTO_MD4=y
+CONFIG_CRYPTO_MD5=y
+CONFIG_CRYPTO_NULL=y
+CONFIG_CRYPTO_NULL2=y
+CONFIG_CRYPTO_RNG=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_RNG_DEFAULT=y
+CONFIG_CRYPTO_SEQIV=y
+CONFIG_CRYPTO_SHA256=y
+CONFIG_CRYPTO_WORKQUEUE=y
+CONFIG_DEBUG_BUGVERBOSE=y
+# CONFIG_DEBUG_KERNEL is not set
+CONFIG_DEBUG_LL_INCLUDE="mach/debug-macro.S"
+CONFIG_DEBUG_MEMORY_INIT=y
+# CONFIG_DEBUG_UART_8250 is not set
+# CONFIG_DEBUG_USER is not set
+CONFIG_DECOMPRESS_BZIP2=y
+CONFIG_DECOMPRESS_GZIP=y
+CONFIG_DECOMPRESS_LZ4=y
+CONFIG_DECOMPRESS_LZMA=y
+CONFIG_DECOMPRESS_LZO=y
+CONFIG_DECOMPRESS_XZ=y
+CONFIG_DEFAULT_CFQ=y
+# CONFIG_DEFAULT_DEADLINE is not set
+CONFIG_DEFAULT_IOSCHED="cfq"
+CONFIG_DEVMEM=y
+CONFIG_DEVTMPFS=y
+CONFIG_DMADEVICES=y
+CONFIG_DMATEST=y
+CONFIG_DMA_ENGINE=y
+CONFIG_DMA_ENGINE_RAID=y
+# CONFIG_DMA_NOOP_OPS is not set
+CONFIG_DMA_OF=y
+CONFIG_DMA_SHARED_BUFFER=y
+CONFIG_DMA_VIRTUAL_CHANNELS=y
+# CONFIG_DMA_VIRT_OPS is not set
+CONFIG_DRM=y
+CONFIG_DRM_BRIDGE=y
+CONFIG_DRM_FBDEV_EMULATION=y
+CONFIG_DRM_FBDEV_OVERALLOC=100
+CONFIG_DRM_KMS_FB_HELPER=y
+CONFIG_DRM_KMS_HELPER=y
+# CONFIG_DRM_LIB_RANDOM is not set
+CONFIG_DRM_PANEL=y
+CONFIG_DRM_PANEL_BRIDGE=y
+CONFIG_DST_CACHE=y
+CONFIG_DTC=y
+CONFIG_DUMMY_CONSOLE=y
+CONFIG_EDAC_ATOMIC_SCRUB=y
+CONFIG_EDAC_SUPPORT=y
+CONFIG_EEPROM_93CX6=y
+CONFIG_ELF_CORE=y
+# CONFIG_EMBEDDED is not set
+# CONFIG_ENABLE_WARN_DEPRECATED is not set
+# CONFIG_EXPERT is not set
+CONFIG_EXPORTFS=y
+CONFIG_EXT4_FS=y
+CONFIG_FARADAY_FTINTC010=y
+CONFIG_FAT_FS=y
+CONFIG_FB=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+CONFIG_FB_CMDLINE=y
+CONFIG_FB_DEFERRED_IO=y
+# CONFIG_FB_PROVIDE_GET_FB_UNMAPPED_AREA is not set
+CONFIG_FB_SYS_COPYAREA=y
+CONFIG_FB_SYS_FILLRECT=y
+CONFIG_FB_SYS_FOPS=y
+CONFIG_FB_SYS_IMAGEBLIT=y
+CONFIG_FHANDLE=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_FIXED_PHY=y
+CONFIG_FIX_EARLYCON_MEM=y
+# CONFIG_FONTS is not set
+CONFIG_FONT_8x16=y
+CONFIG_FONT_8x8=y
+CONFIG_FONT_SUPPORT=y
+# CONFIG_FPE_FASTFPE is not set
+# CONFIG_FPE_NWFPE is not set
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
+CONFIG_FS_MBCACHE=y
+CONFIG_FS_POSIX_ACL=y
+CONFIG_FTTMR010_TIMER=y
+CONFIG_FTWDT010_WATCHDOG=y
+CONFIG_FUTEX_PI=y
+# CONFIG_FW_LOADER_USER_HELPER_FALLBACK is not set
+CONFIG_GEMINI_ETHERNET=y
+CONFIG_GENERIC_ALLOCATOR=y
+CONFIG_GENERIC_ATOMIC64=y
+CONFIG_GENERIC_BUG=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CPU_AUTOPROBE=y
+CONFIG_GENERIC_EARLY_IOREMAP=y
+CONFIG_GENERIC_IDLE_POLL_SETUP=y
+CONFIG_GENERIC_IO=y
+CONFIG_GENERIC_IRQ_SHOW=y
+CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
+CONFIG_GENERIC_PCI_IOMAP=y
+CONFIG_GENERIC_PINCONF=y
+CONFIG_GENERIC_SCHED_CLOCK=y
+CONFIG_GENERIC_SMP_IDLE_THREAD=y
+CONFIG_GENERIC_STRNCPY_FROM_USER=y
+CONFIG_GENERIC_STRNLEN_USER=y
+CONFIG_GLOB=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIOLIB_IRQCHIP=y
+CONFIG_GPIO_FTGPIO010=y
+CONFIG_GPIO_GENERIC=y
+CONFIG_GRO_CELLS=y
+CONFIG_HANDLE_DOMAIN_IRQ=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_HAS_DMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT_MAP=y
+# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
+# CONFIG_HAVE_ARCH_BITREVERSE is not set
+CONFIG_HAVE_ARCH_JUMP_LABEL=y
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_HAVE_ARCH_PFN_VALID=y
+CONFIG_HAVE_ARCH_TRACEHOOK=y
+# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
+CONFIG_HAVE_CC_STACKPROTECTOR=y
+CONFIG_HAVE_CLK=y
+CONFIG_HAVE_CLK_PREPARE=y
+CONFIG_HAVE_CONTEXT_TRACKING=y
+CONFIG_HAVE_C_RECORDMCOUNT=y
+CONFIG_HAVE_DEBUG_KMEMLEAK=y
+CONFIG_HAVE_DMA_API_DEBUG=y
+CONFIG_HAVE_DMA_CONTIGUOUS=y
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+CONFIG_HAVE_DYNAMIC_FTRACE_WITH_REGS=y
+CONFIG_HAVE_EBPF_JIT=y
+CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_HAVE_IDE=y
+CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
+CONFIG_HAVE_MEMBLOCK=y
+CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
+CONFIG_HAVE_NET_DSA=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HAVE_OPTPROBES=y
+CONFIG_HAVE_PERF_EVENTS=y
+CONFIG_HAVE_PERF_REGS=y
+CONFIG_HAVE_PERF_USER_STACK_DUMP=y
+CONFIG_HAVE_PROC_CPU=y
+CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
+CONFIG_HAVE_UID16=y
+CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
+CONFIG_HDMI=y
+CONFIG_HID=y
+CONFIG_HID_A4TECH=y
+CONFIG_HID_APPLE=y
+CONFIG_HID_BELKIN=y
+CONFIG_HID_CHERRY=y
+CONFIG_HID_CHICONY=y
+CONFIG_HID_CYPRESS=y
+CONFIG_HID_EZKEY=y
+CONFIG_HID_GENERIC=y
+CONFIG_HID_ITE=y
+CONFIG_HID_KENSINGTON=y
+CONFIG_HID_LOGITECH=y
+CONFIG_HID_MICROSOFT=y
+CONFIG_HID_MONTEREY=y
+CONFIG_HIGHMEM=y
+CONFIG_HIGHPTE=y
+CONFIG_HWMON=y
+CONFIG_HW_CONSOLE=y
+CONFIG_HZ_FIXED=0
+CONFIG_I2C=y
+CONFIG_I2C_ALGOBIT=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
+CONFIG_I2C_GPIO=y
+CONFIG_I2C_HELPER_AUTO=y
+CONFIG_INET6_XFRM_MODE_BEET=y
+CONFIG_INET6_XFRM_MODE_TRANSPORT=y
+CONFIG_INET6_XFRM_MODE_TUNNEL=y
+CONFIG_INET_DIAG=y
+# CONFIG_INET_DIAG_DESTROY is not set
+# CONFIG_INET_RAW_DIAG is not set
+CONFIG_INET_TCP_DIAG=y
+CONFIG_INET_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+# CONFIG_INITRAMFS_FORCE is not set
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_INPUT=y
+CONFIG_INPUT_EVDEV=y
+CONFIG_INPUT_KEYBOARD=y
+CONFIG_INPUT_LEDS=y
+# CONFIG_INPUT_MISC is not set
+CONFIG_IOMMU_HELPER=y
+# CONFIG_IOMMU_IO_PGTABLE_ARMV7S is not set
+# CONFIG_IOMMU_IO_PGTABLE_LPAE is not set
+CONFIG_IOMMU_SUPPORT=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_IPC_NS=y
+CONFIG_IPV6=y
+CONFIG_IPV6_SIT=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+# CONFIG_IP_MULTICAST is not set
+CONFIG_IRQCHIP=y
+CONFIG_IRQ_DOMAIN=y
+CONFIG_IRQ_FORCED_THREADING=y
+CONFIG_IRQ_WORK=y
+CONFIG_IR_JVC_DECODER=y
+CONFIG_IR_MCE_KBD_DECODER=y
+CONFIG_IR_NEC_DECODER=y
+CONFIG_IR_RC5_DECODER=y
+CONFIG_IR_RC6_DECODER=y
+CONFIG_IR_SANYO_DECODER=y
+CONFIG_IR_SHARP_DECODER=y
+CONFIG_IR_SONY_DECODER=y
+CONFIG_IR_XMP_DECODER=y
+# CONFIG_ISDN is not set
+CONFIG_JBD2=y
+CONFIG_KALLSYMS=y
+CONFIG_KERNEL_LZMA=y
+# CONFIG_KERNEL_XZ is not set
+CONFIG_KEXEC=y
+CONFIG_KEXEC_CORE=y
+CONFIG_KEYBOARD_ATKBD=y
+CONFIG_KEYBOARD_DLINK_DIR685=y
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_LDM_DEBUG is not set
+CONFIG_LDM_PARTITION=y
+# CONFIG_LEDS_BRIGHTNESS_HW_CHANGED is not set
+CONFIG_LEDS_GPIO=y
+# CONFIG_LEDS_TRIGGER_DEFAULT_ON is not set
+CONFIG_LEDS_TRIGGER_DISK=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+# CONFIG_LEDS_TRIGGER_TIMER is not set
+CONFIG_LIBFDT=y
+# CONFIG_LIRC is not set
+CONFIG_LOGO=y
+CONFIG_LOGO_LINUX_CLUT224=y
+CONFIG_LOGO_LINUX_MONO=y
+CONFIG_LOGO_LINUX_VGA16=y
+CONFIG_LZ4_DECOMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+CONFIG_MANDATORY_FILE_LOCKING=y
+CONFIG_MDIO_BITBANG=y
+CONFIG_MDIO_BUS=y
+CONFIG_MDIO_DEVICE=y
+CONFIG_MDIO_GPIO=y
+# CONFIG_MEMCG is not set
+CONFIG_MFD_SYSCON=y
+CONFIG_MIGHT_HAVE_PCI=y
+CONFIG_MIGRATION=y
+CONFIG_MODULES_USE_ELF_REL=y
+# CONFIG_MODULE_UNLOAD is not set
+CONFIG_MQ_IOSCHED_DEADLINE=y
+CONFIG_MQ_IOSCHED_KYBER=y
+CONFIG_MTD_CFI_STAA=y
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_PHYSMAP_OF_GEMINI=y
+CONFIG_MULTI_IRQ_HANDLER=y
+CONFIG_NAMESPACES=y
+CONFIG_NEED_DMA_MAP_STATE=y
+CONFIG_NEED_KUSER_HELPERS=y
+CONFIG_NEED_PER_CPU_KM=y
+# CONFIG_NET_CLS_CGROUP is not set
+CONFIG_NET_DSA=y
+CONFIG_NET_IP_TUNNEL=y
+CONFIG_NET_NS=y
+CONFIG_NET_PACKET_ENGINE=y
+CONFIG_NET_SWITCHDEV=y
+# CONFIG_NET_VENDOR_AURORA is not set
+CONFIG_NET_VENDOR_CORTINA=y
+# CONFIG_NL80211_TESTMODE is not set
+CONFIG_NLS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NO_BOOTMEM=y
+CONFIG_NO_HZ_COMMON=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_NVMEM=y
+CONFIG_OABI_COMPAT=y
+CONFIG_OF=y
+CONFIG_OF_ADDRESS=y
+CONFIG_OF_ADDRESS_PCI=y
+CONFIG_OF_EARLY_FLATTREE=y
+CONFIG_OF_FLATTREE=y
+CONFIG_OF_GPIO=y
+CONFIG_OF_IRQ=y
+CONFIG_OF_MDIO=y
+CONFIG_OF_NET=y
+CONFIG_OF_PCI=y
+CONFIG_OF_PCI_IRQ=y
+CONFIG_OF_RESERVED_MEM=y
+CONFIG_OLD_SIGACTION=y
+CONFIG_OLD_SIGSUSPEND3=y
+# CONFIG_PACKET is not set
+CONFIG_PAGE_OFFSET=0xC0000000
+# CONFIG_PANIC_ON_OOPS is not set
+CONFIG_PANIC_ON_OOPS_VALUE=0
+CONFIG_PANIC_TIMEOUT=0
+CONFIG_PATA_FTIDE010=y
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+CONFIG_PCI_DOMAINS_GENERIC=y
+CONFIG_PCI_FTPCI100=y
+CONFIG_PERF_USE_VMALLOC=y
+CONFIG_PGTABLE_LEVELS=2
+CONFIG_PHYLIB=y
+CONFIG_PID_NS=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_GEMINI=y
+# CONFIG_PINCTRL_SINGLE is not set
+CONFIG_PM=y
+CONFIG_PM_CLK=y
+# CONFIG_PM_DEBUG is not set
+CONFIG_POWER_RESET=y
+CONFIG_POWER_RESET_GEMINI_POWEROFF=y
+CONFIG_POWER_RESET_SYSCON=y
+CONFIG_PREEMPT=y
+CONFIG_PREEMPT_COUNT=y
+# CONFIG_PREEMPT_NONE is not set
+CONFIG_PREEMPT_RCU=y
+CONFIG_PROC_PAGE_MONITOR=y
+# CONFIG_QTNFMAC_PEARL_PCIE is not set
+CONFIG_RATIONAL=y
+CONFIG_RCU_CPU_STALL_TIMEOUT=21
+# CONFIG_RCU_EXPERT is not set
+CONFIG_RCU_NEED_SEGCBLIST=y
+CONFIG_RCU_STALL_COMMON=y
+CONFIG_RC_CORE=y
+CONFIG_RC_DECODERS=y
+# CONFIG_RC_DEVICES is not set
+CONFIG_RC_MAP=y
+CONFIG_RD_BZIP2=y
+CONFIG_RD_GZIP=y
+CONFIG_RD_LZ4=y
+CONFIG_RD_LZMA=y
+CONFIG_RD_LZO=y
+CONFIG_RD_XZ=y
+CONFIG_REALTEK_PHY=y
+CONFIG_REGMAP=y
+CONFIG_REGMAP_I2C=y
+CONFIG_REGMAP_MMIO=y
+CONFIG_REGMAP_SPI=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_RELAY=y
+CONFIG_RESET_CONTROLLER=y
+CONFIG_ROMFS_BACKED_BY_BLOCK=y
+# CONFIG_ROMFS_BACKED_BY_BOTH is not set
+# CONFIG_ROMFS_BACKED_BY_MTD is not set
+CONFIG_ROMFS_FS=y
+CONFIG_ROMFS_ON_BLOCK=y
+CONFIG_RTC_CLASS=y
+# CONFIG_RTC_DRV_CMOS is not set
+CONFIG_RTC_DRV_FTRTC010=y
+CONFIG_RTC_I2C_AND_SPI=y
+CONFIG_RTC_NVMEM=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_SATA_GEMINI=y
+CONFIG_SATA_PMP=y
+# CONFIG_SCHED_INFO is not set
+CONFIG_SCSI=y
+# CONFIG_SCSI_LOWLEVEL is not set
+# CONFIG_SCSI_PROC_FS is not set
+CONFIG_SENSORS_GPIO_FAN=y
+CONFIG_SENSORS_LM75=y
+CONFIG_SERIAL_8250_DEPRECATED_OPTIONS=y
+CONFIG_SERIAL_8250_EXAR=y
+CONFIG_SERIAL_8250_FSL=y
+CONFIG_SERIAL_8250_NR_UARTS=1
+CONFIG_SERIAL_8250_PCI=y
+CONFIG_SERIAL_8250_RUNTIME_UARTS=1
+# CONFIG_SERIAL_AMBA_PL011 is not set
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SERIO=y
+CONFIG_SERIO_LIBPS2=y
+CONFIG_SERIO_SERPORT=y
+CONFIG_SG_POOL=y
+CONFIG_SLUB_DEBUG=y
+CONFIG_SOCK_DIAG=y
+CONFIG_SPARSE_IRQ=y
+CONFIG_SPI=y
+CONFIG_SPI_BITBANG=y
+CONFIG_SPI_GPIO=y
+CONFIG_SPI_MASTER=y
+CONFIG_SPLIT_PTLOCK_CPUS=999999
+CONFIG_SRCU=y
+# CONFIG_STAGING is not set
+# CONFIG_STRICT_KERNEL_RWX is not set
+# CONFIG_STRICT_MODULE_RWX is not set
+# CONFIG_STRIP_ASM_SYMS is not set
+CONFIG_SWIOTLB=y
+CONFIG_SWPHY=y
+CONFIG_SYNC_FILE=y
+# CONFIG_SYN_COOKIES is not set
+CONFIG_SYSFS_SYSCALL=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_TASKS_RCU=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_THERMAL=y
+CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
+CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0
+CONFIG_THERMAL_GOV_STEP_WISE=y
+CONFIG_THERMAL_HWMON=y
+CONFIG_THERMAL_OF=y
+CONFIG_THIN_ARCHIVES=y
+CONFIG_TICK_CPU_ACCOUNTING=y
+CONFIG_TIMER_OF=y
+CONFIG_TIMER_PROBE=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_TREE_SRCU=y
+CONFIG_TUN=y
+CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h"
+CONFIG_UNINLINE_SPIN_UNLOCK=y
+CONFIG_USB=y
+CONFIG_USB_COMMON=y
+# CONFIG_USB_EHCI_HCD is not set
+CONFIG_USB_FOTG210_HCD=y
+CONFIG_USB_SUPPORT=y
+# CONFIG_USB_UHCI_HCD is not set
+# CONFIG_USERIO is not set
+CONFIG_USER_NS=y
+CONFIG_USE_OF=y
+CONFIG_UTS_NS=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_VFAT_FS=y
+CONFIG_VGA_ARB=y
+CONFIG_VGA_ARB_MAX_GPUS=16
+# CONFIG_VLAN_8021Q is not set
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_VT=y
+CONFIG_VT_CONSOLE=y
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_WATCHDOG_CORE=y
+CONFIG_WLAN_VENDOR_QUANTENNA=y
+CONFIG_WLAN_VENDOR_RALINK=y
+# CONFIG_WQ_POWER_EFFICIENT_DEFAULT is not set
+CONFIG_XZ_DEC_ARM=y
+CONFIG_XZ_DEC_ARMTHUMB=y
+CONFIG_XZ_DEC_BCJ=y
+CONFIG_XZ_DEC_IA64=y
+CONFIG_XZ_DEC_POWERPC=y
+CONFIG_XZ_DEC_SPARC=y
+CONFIG_XZ_DEC_X86=y
+CONFIG_ZBOOT_ROM_BSS=0
+CONFIG_ZBOOT_ROM_TEXT=0
+CONFIG_ZLIB_INFLATE=y
diff --git a/target/linux/gemini/patches-4.14/0001-cache-patch-from-OpenWRT.patch b/target/linux/gemini/patches-4.14/0001-cache-patch-from-OpenWRT.patch
new file mode 100644
index 0000000..4430ffe
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0001-cache-patch-from-OpenWRT.patch
@@ -0,0 +1,50 @@
+From 57615e112aba6ae4c831d50e769c2c102f013686 Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Tue, 7 Jun 2016 22:53:24 +0200
+Subject: [PATCH 01/31] cache patch from OpenWRT
+
+---
+ arch/arm/mm/cache-fa.S | 17 ++++++++++++++++-
+ 1 file changed, 16 insertions(+), 1 deletion(-)
+
+--- a/arch/arm/mm/cache-fa.S
++++ b/arch/arm/mm/cache-fa.S
+@@ -24,7 +24,8 @@
+ /*
+ * The size of one data cache line.
+ */
+-#define CACHE_DLINESIZE 16
++#define CACHE_DLINESIZE 16
++#define CACHE_DLINESHIFT 4
+
+ /*
+ * The total size of the data cache.
+@@ -169,7 +170,17 @@ ENTRY(fa_flush_kern_dcache_area)
+ * - start - virtual start address
+ * - end - virtual end address
+ */
++__flush_whole_dcache:
++ mcr p15, 0, r0, c7, c14, 0 @ clean/invalidate D cache
++ mov r0, #0
++ mcr p15, 0, r0, c7, c10, 4 @ drain write buffer
++ mov pc, lr
++
+ fa_dma_inv_range:
++ sub r3, r1, r0 @ calculate total size
++ cmp r3, #CACHE_DLIMIT @ total size >= limit?
++ bhs __flush_whole_dcache @ flush whole D cache
++
+ tst r0, #CACHE_DLINESIZE - 1
+ bic r0, r0, #CACHE_DLINESIZE - 1
+ mcrne p15, 0, r0, c7, c14, 1 @ clean & invalidate D entry
+@@ -193,6 +204,10 @@ fa_dma_inv_range:
+ * - end - virtual end address
+ */
+ fa_dma_clean_range:
++ sub r3, r1, r0 @ calculate total size
++ cmp r3, #CACHE_DLIMIT @ total size >= limit?
++ bhs __flush_whole_dcache @ flush whole D cache
++
+ bic r0, r0, #CACHE_DLINESIZE - 1
+ 1: mcr p15, 0, r0, c7, c10, 1 @ clean D entry
+ add r0, r0, #CACHE_DLINESIZE
diff --git a/target/linux/gemini/patches-4.14/0002-pinctrl-gemini-Add-missing-functions.patch b/target/linux/gemini/patches-4.14/0002-pinctrl-gemini-Add-missing-functions.patch
new file mode 100644
index 0000000..604fee4
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0002-pinctrl-gemini-Add-missing-functions.patch
@@ -0,0 +1,33 @@
+From fd7823e6993f440930e9cb85e56375be5823485c Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Sat, 14 Oct 2017 17:13:03 +0200
+Subject: [PATCH 02/31] pinctrl: gemini: Add missing functions
+
+Some two functions were missing from the Gemini pin control
+driver. Noticed when trying to use ethernet. Fix it up by
+adding them.
+
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+---
+ drivers/pinctrl/pinctrl-gemini.c | 10 ++++++++++
+ 1 file changed, 10 insertions(+)
+
+--- a/drivers/pinctrl/pinctrl-gemini.c
++++ b/drivers/pinctrl/pinctrl-gemini.c
+@@ -2074,6 +2074,16 @@ static const struct gemini_pmx_func gemi
+ .num_groups = ARRAY_SIZE(satagrps),
+ },
+ {
++ .name = "usb",
++ .groups = usbgrps,
++ .num_groups = ARRAY_SIZE(usbgrps),
++ },
++ {
++ .name = "gmii",
++ .groups = gmiigrps,
++ .num_groups = ARRAY_SIZE(gmiigrps),
++ },
++ {
+ .name = "pci",
+ .groups = pcigrps,
+ .num_groups = ARRAY_SIZE(pcigrps),
diff --git a/target/linux/gemini/patches-4.14/0003-ARM-dts-Add-TVE200-to-the-Gemini-SoC-DTSI.patch b/target/linux/gemini/patches-4.14/0003-ARM-dts-Add-TVE200-to-the-Gemini-SoC-DTSI.patch
new file mode 100644
index 0000000..81d9788
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0003-ARM-dts-Add-TVE200-to-the-Gemini-SoC-DTSI.patch
@@ -0,0 +1,51 @@
+From 00e53d08bbe92051765c5bb94223b6f628cd3740 Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Wed, 11 Oct 2017 19:45:19 +0200
+Subject: [PATCH 03/31] ARM: dts: Add TVE200 to the Gemini SoC DTSI
+
+The Faraday TVE200 is present in the Gemini SoC, sometimes
+under the name "TVC". Add it to the SoC DTSI file along with
+its resources.
+
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+Signed-off-by: Arnd Bergmann <arnd at arndb.de>
+---
+ arch/arm/boot/dts/gemini.dtsi | 21 +++++++++++++++++++++
+ 1 file changed, 21 insertions(+)
+
+--- a/arch/arm/boot/dts/gemini.dtsi
++++ b/arch/arm/boot/dts/gemini.dtsi
+@@ -142,6 +142,12 @@
+ groups = "idegrp";
+ };
+ };
++ tvc_default_pins: pinctrl-tvc {
++ mux {
++ function = "tvc";
++ groups = "tvcgrp";
++ };
++ };
+ };
+ };
+
+@@ -348,5 +354,20 @@
+ memcpy-bus-width = <32>;
+ #dma-cells = <2>;
+ };
++
++ display-controller at 6a000000 {
++ compatible = "cortina,gemini-tvc", "faraday,tve200";
++ reg = <0x6a000000 0x1000>;
++ interrupts = <13 IRQ_TYPE_EDGE_RISING>;
++ resets = <&syscon GEMINI_RESET_TVC>;
++ clocks = <&syscon GEMINI_CLK_GATE_TVC>,
++ <&syscon GEMINI_CLK_TVC>;
++ clock-names = "PCLK", "TVE";
++ pinctrl-names = "default";
++ pinctrl-0 = <&tvc_default_pins>;
++ #address-cells = <1>;
++ #size-cells = <0>;
++ status = "disabled";
++ };
+ };
+ };
diff --git a/target/linux/gemini/patches-4.14/0004-pinctrl-Add-skew-delay-pin-config-and-bindings.patch b/target/linux/gemini/patches-4.14/0004-pinctrl-Add-skew-delay-pin-config-and-bindings.patch
new file mode 100644
index 0000000..ac39a32
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0004-pinctrl-Add-skew-delay-pin-config-and-bindings.patch
@@ -0,0 +1,73 @@
+From eb3742c4250c6a79e7080bdb6286e5df50c7f26a Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Sat, 28 Oct 2017 15:37:17 +0200
+Subject: [PATCH 04/31] pinctrl: Add skew-delay pin config and bindings
+
+Some pin controllers (such as the Gemini) can control the
+expected clock skew and output delay on certain pins with a
+sub-nanosecond granularity. This is typically done by shunting
+in a number of double inverters in front of or behind the pin.
+Make it possible to configure this with a generic binding.
+
+Cc: devicetree at vger.kernel.org
+Acked-by: Rob Herring <robh at kernel.org>
+Acked-by: Hans Ulli Kroll <ulli.kroll at googlemail.com>
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+---
+ Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt | 4 ++++
+ drivers/pinctrl/pinconf-generic.c | 2 ++
+ include/linux/pinctrl/pinconf-generic.h | 5 +++++
+ 3 files changed, 11 insertions(+)
+
+--- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
++++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+@@ -271,6 +271,10 @@ output-high - set the pin to output mod
+ sleep-hardware-state - indicate this is sleep related state which will be programmed
+ into the registers for the sleep state.
+ slew-rate - set the slew rate
++skew-delay - this affects the expected clock skew on input pins
++ and the delay before latching a value to an output
++ pin. Typically indicates how many double-inverters are
++ used to delay the signal.
+
+ For example:
+
+--- a/drivers/pinctrl/pinconf-generic.c
++++ b/drivers/pinctrl/pinconf-generic.c
+@@ -49,6 +49,7 @@ static const struct pin_config_item conf
+ PCONFDUMP(PIN_CONFIG_POWER_SOURCE, "pin power source", "selector", true),
+ PCONFDUMP(PIN_CONFIG_SLEEP_HARDWARE_STATE, "sleep hardware state", NULL, false),
+ PCONFDUMP(PIN_CONFIG_SLEW_RATE, "slew rate", NULL, true),
++ PCONFDUMP(PIN_CONFIG_SKEW_DELAY, "skew delay", NULL, true),
+ };
+
+ static void pinconf_generic_dump_one(struct pinctrl_dev *pctldev,
+@@ -181,6 +182,7 @@ static const struct pinconf_generic_para
+ { "power-source", PIN_CONFIG_POWER_SOURCE, 0 },
+ { "sleep-hardware-state", PIN_CONFIG_SLEEP_HARDWARE_STATE, 0 },
+ { "slew-rate", PIN_CONFIG_SLEW_RATE, 0 },
++ { "skew-delay", PIN_CONFIG_SKEW_DELAY, 0 },
+ };
+
+ /**
+--- a/include/linux/pinctrl/pinconf-generic.h
++++ b/include/linux/pinctrl/pinconf-generic.h
+@@ -90,6 +90,10 @@
+ * @PIN_CONFIG_SLEW_RATE: if the pin can select slew rate, the argument to
+ * this parameter (on a custom format) tells the driver which alternative
+ * slew rate to use.
++ * @PIN_CONFIG_SKEW_DELAY: if the pin has programmable skew rate (on inputs)
++ * or latch delay (on outputs) this parameter (in a custom format)
++ * specifies the clock skew or latch delay. It typically controls how
++ * many double inverters are put in front of the line.
+ * @PIN_CONFIG_END: this is the last enumerator for pin configurations, if
+ * you need to pass in custom configurations to the pin controller, use
+ * PIN_CONFIG_END+1 as the base offset.
+@@ -117,6 +121,7 @@ enum pin_config_param {
+ PIN_CONFIG_POWER_SOURCE,
+ PIN_CONFIG_SLEEP_HARDWARE_STATE,
+ PIN_CONFIG_SLEW_RATE,
++ PIN_CONFIG_SKEW_DELAY,
+ PIN_CONFIG_END = 0x7F,
+ PIN_CONFIG_MAX = 0xFF,
+ };
diff --git a/target/linux/gemini/patches-4.14/0005-pinctrl-gemini-Use-generic-DT-parser.patch b/target/linux/gemini/patches-4.14/0005-pinctrl-gemini-Use-generic-DT-parser.patch
new file mode 100644
index 0000000..5b0bba1
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0005-pinctrl-gemini-Use-generic-DT-parser.patch
@@ -0,0 +1,112 @@
+From 09240ae27ffca65518f7b9d2360c020c1b1ddabe Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Sat, 28 Oct 2017 15:37:18 +0200
+Subject: [PATCH 05/31] pinctrl: gemini: Use generic DT parser
+
+We can just use the generic Device Tree parser code
+in this driver and save some code.
+
+Acked-by: Hans Ulli Kroll <ulli.kroll at googlemail.com>
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+---
+ drivers/pinctrl/Kconfig | 1 +
+ drivers/pinctrl/pinctrl-gemini.c | 66 +++-------------------------------------
+ 2 files changed, 5 insertions(+), 62 deletions(-)
+
+--- a/drivers/pinctrl/Kconfig
++++ b/drivers/pinctrl/Kconfig
+@@ -153,6 +153,7 @@ config PINCTRL_GEMINI
+ depends on ARCH_GEMINI
+ default ARCH_GEMINI
+ select PINMUX
++ select GENERIC_PINCONF
+ select MFD_SYSCON
+
+ config PINCTRL_MCP23S08
+--- a/drivers/pinctrl/pinctrl-gemini.c
++++ b/drivers/pinctrl/pinctrl-gemini.c
+@@ -13,6 +13,8 @@
+ #include <linux/pinctrl/machine.h>
+ #include <linux/pinctrl/pinctrl.h>
+ #include <linux/pinctrl/pinmux.h>
++#include <linux/pinctrl/pinconf.h>
++#include <linux/pinctrl/pinconf-generic.h>
+ #include <linux/platform_device.h>
+ #include <linux/slab.h>
+ #include <linux/regmap.h>
+@@ -1918,73 +1920,13 @@ static void gemini_pin_dbg_show(struct p
+ seq_printf(s, " " DRIVER_NAME);
+ }
+
+-static int gemini_pinctrl_dt_subnode_to_map(struct pinctrl_dev *pctldev,
+- struct device_node *np,
+- struct pinctrl_map **map,
+- unsigned int *reserved_maps,
+- unsigned int *num_maps)
+-{
+- int ret;
+- const char *function = NULL;
+- const char *group;
+- struct property *prop;
+-
+- ret = of_property_read_string(np, "function", &function);
+- if (ret < 0)
+- return ret;
+-
+- ret = of_property_count_strings(np, "groups");
+- if (ret < 0)
+- return ret;
+-
+- ret = pinctrl_utils_reserve_map(pctldev, map, reserved_maps,
+- num_maps, ret);
+- if (ret < 0)
+- return ret;
+-
+- of_property_for_each_string(np, "groups", prop, group) {
+- ret = pinctrl_utils_add_map_mux(pctldev, map, reserved_maps,
+- num_maps, group, function);
+- if (ret < 0)
+- return ret;
+- pr_debug("ADDED FUNCTION %s <-> GROUP %s\n",
+- function, group);
+- }
+-
+- return 0;
+-}
+-
+-static int gemini_pinctrl_dt_node_to_map(struct pinctrl_dev *pctldev,
+- struct device_node *np_config,
+- struct pinctrl_map **map,
+- unsigned int *num_maps)
+-{
+- unsigned int reserved_maps = 0;
+- struct device_node *np;
+- int ret;
+-
+- *map = NULL;
+- *num_maps = 0;
+-
+- for_each_child_of_node(np_config, np) {
+- ret = gemini_pinctrl_dt_subnode_to_map(pctldev, np, map,
+- &reserved_maps, num_maps);
+- if (ret < 0) {
+- pinctrl_utils_free_map(pctldev, *map, *num_maps);
+- return ret;
+- }
+- }
+-
+- return 0;
+-};
+-
+ static const struct pinctrl_ops gemini_pctrl_ops = {
+ .get_groups_count = gemini_get_groups_count,
+ .get_group_name = gemini_get_group_name,
+ .get_group_pins = gemini_get_group_pins,
+ .pin_dbg_show = gemini_pin_dbg_show,
+- .dt_node_to_map = gemini_pinctrl_dt_node_to_map,
+- .dt_free_map = pinctrl_utils_free_map,
++ .dt_node_to_map = pinconf_generic_dt_node_to_map_group,
++ .dt_free_map = pinconf_generic_dt_free_map,
+ };
+
+ /**
diff --git a/target/linux/gemini/patches-4.14/0006-pinctrl-gemini-Implement-clock-skew-delay-config.patch b/target/linux/gemini/patches-4.14/0006-pinctrl-gemini-Implement-clock-skew-delay-config.patch
new file mode 100644
index 0000000..4bff3bc
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0006-pinctrl-gemini-Implement-clock-skew-delay-config.patch
@@ -0,0 +1,280 @@
+From 43e8f011ddbb293e0a3394d0f39819ea2ead4a1b Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Sat, 28 Oct 2017 15:37:19 +0200
+Subject: [PATCH 06/31] pinctrl: gemini: Implement clock skew/delay config
+
+This enabled pin config on the Gemini driver and implements
+pin skew/delay so that the ethernet pins clocking can be
+properly configured.
+
+Acked-by: Hans Ulli Kroll <ulli.kroll at googlemail.com>
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+---
+ .../bindings/pinctrl/cortina,gemini-pinctrl.txt | 10 +-
+ drivers/pinctrl/pinctrl-gemini.c | 178 ++++++++++++++++++++-
+ 2 files changed, 182 insertions(+), 6 deletions(-)
+
+--- a/Documentation/devicetree/bindings/pinctrl/cortina,gemini-pinctrl.txt
++++ b/Documentation/devicetree/bindings/pinctrl/cortina,gemini-pinctrl.txt
+@@ -9,8 +9,14 @@ The pin controller node must be a subnod
+ Required properties:
+ - compatible: "cortina,gemini-pinctrl"
+
+-Subnodes of the pin controller contain pin control multiplexing set-up.
+-Please refer to pinctrl-bindings.txt for generic pin multiplexing nodes.
++Subnodes of the pin controller contain pin control multiplexing set-up
++and pin configuration of individual pins.
++
++Please refer to pinctrl-bindings.txt for generic pin multiplexing nodes
++and generic pin config nodes.
++
++Supported configurations:
++- skew-delay is supported on the Ethernet pins
+
+ Example:
+
+--- a/drivers/pinctrl/pinctrl-gemini.c
++++ b/drivers/pinctrl/pinctrl-gemini.c
+@@ -24,6 +24,19 @@
+ #define DRIVER_NAME "pinctrl-gemini"
+
+ /**
++ * struct gemini_pin_conf - information about configuring a pin
++ * @pin: the pin number
++ * @reg: config register
++ * @mask: the bits affecting the configuration of the pin
++ */
++struct gemini_pin_conf {
++ unsigned int pin;
++ u32 reg;
++ u32 mask;
++};
++
++/**
++ * struct gemini_pmx - state holder for the gemini pin controller
+ * @dev: a pointer back to containing device
+ * @virtbase: the offset to the controller in virtual memory
+ * @map: regmap to access registers
+@@ -31,6 +44,8 @@
+ * @is_3516: whether the SoC/package is the 3516 variant
+ * @flash_pin: whether the flash pin (extended pins for parallel
+ * flash) is set
++ * @confs: pin config information
++ * @nconfs: number of pin config information items
+ */
+ struct gemini_pmx {
+ struct device *dev;
+@@ -39,6 +54,8 @@ struct gemini_pmx {
+ bool is_3512;
+ bool is_3516;
+ bool flash_pin;
++ const struct gemini_pin_conf *confs;
++ unsigned int nconfs;
+ };
+
+ /**
+@@ -59,6 +76,13 @@ struct gemini_pin_group {
+ u32 value;
+ };
+
++/* Some straight-forward control registers */
++#define GLOBAL_WORD_ID 0x00
++#define GLOBAL_STATUS 0x04
++#define GLOBAL_STATUS_FLPIN BIT(20)
++#define GLOBAL_GMAC_CTRL_SKEW 0x1c
++#define GLOBAL_GMAC0_DATA_SKEW 0x20
++#define GLOBAL_GMAC1_DATA_SKEW 0x24
+ /*
+ * Global Miscellaneous Control Register
+ * This register controls all Gemini pad/pin multiplexing
+@@ -71,9 +95,6 @@ struct gemini_pin_group {
+ * DISABLED again. So you select a flash configuration once, and then
+ * you are stuck with it.
+ */
+-#define GLOBAL_WORD_ID 0x00
+-#define GLOBAL_STATUS 0x04
+-#define GLOBAL_STATUS_FLPIN BIT(20)
+ #define GLOBAL_MISC_CTRL 0x30
+ #define TVC_CLK_PAD_ENABLE BIT(20)
+ #define PCI_CLK_PAD_ENABLE BIT(17)
+@@ -1925,7 +1946,7 @@ static const struct pinctrl_ops gemini_p
+ .get_group_name = gemini_get_group_name,
+ .get_group_pins = gemini_get_group_pins,
+ .pin_dbg_show = gemini_pin_dbg_show,
+- .dt_node_to_map = pinconf_generic_dt_node_to_map_group,
++ .dt_node_to_map = pinconf_generic_dt_node_to_map_all,
+ .dt_free_map = pinconf_generic_dt_free_map,
+ };
+
+@@ -2203,10 +2224,155 @@ static const struct pinmux_ops gemini_pm
+ .set_mux = gemini_pmx_set_mux,
+ };
+
++#define GEMINI_CFGPIN(_n, _r, _lb, _hb) { \
++ .pin = _n, \
++ .reg = _r, \
++ .mask = GENMASK(_hb, _lb) \
++}
++
++static const struct gemini_pin_conf gemini_confs_3512[] = {
++ GEMINI_CFGPIN(259, GLOBAL_GMAC_CTRL_SKEW, 0, 3), /* GMAC0 RXDV */
++ GEMINI_CFGPIN(277, GLOBAL_GMAC_CTRL_SKEW, 4, 7), /* GMAC0 RXC */
++ GEMINI_CFGPIN(241, GLOBAL_GMAC_CTRL_SKEW, 8, 11), /* GMAC0 TXEN */
++ GEMINI_CFGPIN(312, GLOBAL_GMAC_CTRL_SKEW, 12, 15), /* GMAC0 TXC */
++ GEMINI_CFGPIN(298, GLOBAL_GMAC_CTRL_SKEW, 16, 19), /* GMAC1 RXDV */
++ GEMINI_CFGPIN(280, GLOBAL_GMAC_CTRL_SKEW, 20, 23), /* GMAC1 RXC */
++ GEMINI_CFGPIN(316, GLOBAL_GMAC_CTRL_SKEW, 24, 27), /* GMAC1 TXEN */
++ GEMINI_CFGPIN(243, GLOBAL_GMAC_CTRL_SKEW, 28, 31), /* GMAC1 TXC */
++ GEMINI_CFGPIN(295, GLOBAL_GMAC0_DATA_SKEW, 0, 3), /* GMAC0 RXD0 */
++ GEMINI_CFGPIN(313, GLOBAL_GMAC0_DATA_SKEW, 4, 7), /* GMAC0 RXD1 */
++ GEMINI_CFGPIN(242, GLOBAL_GMAC0_DATA_SKEW, 8, 11), /* GMAC0 RXD2 */
++ GEMINI_CFGPIN(260, GLOBAL_GMAC0_DATA_SKEW, 12, 15), /* GMAC0 RXD3 */
++ GEMINI_CFGPIN(294, GLOBAL_GMAC0_DATA_SKEW, 16, 19), /* GMAC0 TXD0 */
++ GEMINI_CFGPIN(276, GLOBAL_GMAC0_DATA_SKEW, 20, 23), /* GMAC0 TXD1 */
++ GEMINI_CFGPIN(258, GLOBAL_GMAC0_DATA_SKEW, 24, 27), /* GMAC0 TXD2 */
++ GEMINI_CFGPIN(240, GLOBAL_GMAC0_DATA_SKEW, 28, 31), /* GMAC0 TXD3 */
++ GEMINI_CFGPIN(262, GLOBAL_GMAC1_DATA_SKEW, 0, 3), /* GMAC1 RXD0 */
++ GEMINI_CFGPIN(244, GLOBAL_GMAC1_DATA_SKEW, 4, 7), /* GMAC1 RXD1 */
++ GEMINI_CFGPIN(317, GLOBAL_GMAC1_DATA_SKEW, 8, 11), /* GMAC1 RXD2 */
++ GEMINI_CFGPIN(299, GLOBAL_GMAC1_DATA_SKEW, 12, 15), /* GMAC1 RXD3 */
++ GEMINI_CFGPIN(261, GLOBAL_GMAC1_DATA_SKEW, 16, 19), /* GMAC1 TXD0 */
++ GEMINI_CFGPIN(279, GLOBAL_GMAC1_DATA_SKEW, 20, 23), /* GMAC1 TXD1 */
++ GEMINI_CFGPIN(297, GLOBAL_GMAC1_DATA_SKEW, 24, 27), /* GMAC1 TXD2 */
++ GEMINI_CFGPIN(315, GLOBAL_GMAC1_DATA_SKEW, 28, 31), /* GMAC1 TXD3 */
++};
++
++static const struct gemini_pin_conf gemini_confs_3516[] = {
++ GEMINI_CFGPIN(347, GLOBAL_GMAC_CTRL_SKEW, 0, 3), /* GMAC0 RXDV */
++ GEMINI_CFGPIN(386, GLOBAL_GMAC_CTRL_SKEW, 4, 7), /* GMAC0 RXC */
++ GEMINI_CFGPIN(307, GLOBAL_GMAC_CTRL_SKEW, 8, 11), /* GMAC0 TXEN */
++ GEMINI_CFGPIN(327, GLOBAL_GMAC_CTRL_SKEW, 12, 15), /* GMAC0 TXC */
++ GEMINI_CFGPIN(309, GLOBAL_GMAC_CTRL_SKEW, 16, 19), /* GMAC1 RXDV */
++ GEMINI_CFGPIN(390, GLOBAL_GMAC_CTRL_SKEW, 20, 23), /* GMAC1 RXC */
++ GEMINI_CFGPIN(370, GLOBAL_GMAC_CTRL_SKEW, 24, 27), /* GMAC1 TXEN */
++ GEMINI_CFGPIN(350, GLOBAL_GMAC_CTRL_SKEW, 28, 31), /* GMAC1 TXC */
++ GEMINI_CFGPIN(367, GLOBAL_GMAC0_DATA_SKEW, 0, 3), /* GMAC0 RXD0 */
++ GEMINI_CFGPIN(348, GLOBAL_GMAC0_DATA_SKEW, 4, 7), /* GMAC0 RXD1 */
++ GEMINI_CFGPIN(387, GLOBAL_GMAC0_DATA_SKEW, 8, 11), /* GMAC0 RXD2 */
++ GEMINI_CFGPIN(328, GLOBAL_GMAC0_DATA_SKEW, 12, 15), /* GMAC0 RXD3 */
++ GEMINI_CFGPIN(306, GLOBAL_GMAC0_DATA_SKEW, 16, 19), /* GMAC0 TXD0 */
++ GEMINI_CFGPIN(325, GLOBAL_GMAC0_DATA_SKEW, 20, 23), /* GMAC0 TXD1 */
++ GEMINI_CFGPIN(346, GLOBAL_GMAC0_DATA_SKEW, 24, 27), /* GMAC0 TXD2 */
++ GEMINI_CFGPIN(326, GLOBAL_GMAC0_DATA_SKEW, 28, 31), /* GMAC0 TXD3 */
++ GEMINI_CFGPIN(391, GLOBAL_GMAC1_DATA_SKEW, 0, 3), /* GMAC1 RXD0 */
++ GEMINI_CFGPIN(351, GLOBAL_GMAC1_DATA_SKEW, 4, 7), /* GMAC1 RXD1 */
++ GEMINI_CFGPIN(310, GLOBAL_GMAC1_DATA_SKEW, 8, 11), /* GMAC1 RXD2 */
++ GEMINI_CFGPIN(371, GLOBAL_GMAC1_DATA_SKEW, 12, 15), /* GMAC1 RXD3 */
++ GEMINI_CFGPIN(329, GLOBAL_GMAC1_DATA_SKEW, 16, 19), /* GMAC1 TXD0 */
++ GEMINI_CFGPIN(389, GLOBAL_GMAC1_DATA_SKEW, 20, 23), /* GMAC1 TXD1 */
++ GEMINI_CFGPIN(369, GLOBAL_GMAC1_DATA_SKEW, 24, 27), /* GMAC1 TXD2 */
++ GEMINI_CFGPIN(308, GLOBAL_GMAC1_DATA_SKEW, 28, 31), /* GMAC1 TXD3 */
++};
++
++static const struct gemini_pin_conf *gemini_get_pin_conf(struct gemini_pmx *pmx,
++ unsigned int pin)
++{
++ const struct gemini_pin_conf *retconf;
++ int i;
++
++ for (i = 0; i < pmx->nconfs; i++) {
++ retconf = &gemini_confs_3516[i];
++ if (retconf->pin == pin)
++ return retconf;
++ }
++ return NULL;
++}
++
++static int gemini_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin,
++ unsigned long *config)
++{
++ struct gemini_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
++ enum pin_config_param param = pinconf_to_config_param(*config);
++ const struct gemini_pin_conf *conf;
++ u32 val;
++
++ switch (param) {
++ case PIN_CONFIG_SKEW_DELAY:
++ conf = gemini_get_pin_conf(pmx, pin);
++ if (!conf)
++ return -ENOTSUPP;
++ regmap_read(pmx->map, conf->reg, &val);
++ val &= conf->mask;
++ val >>= (ffs(conf->mask) - 1);
++ *config = pinconf_to_config_packed(PIN_CONFIG_SKEW_DELAY, val);
++ break;
++ default:
++ return -ENOTSUPP;
++ }
++
++ return 0;
++}
++
++static int gemini_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
++ unsigned long *configs, unsigned int num_configs)
++{
++ struct gemini_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
++ const struct gemini_pin_conf *conf;
++ enum pin_config_param param;
++ u32 arg;
++ int ret = 0;
++ int i;
++
++ for (i = 0; i < num_configs; i++) {
++ param = pinconf_to_config_param(configs[i]);
++ arg = pinconf_to_config_argument(configs[i]);
++
++ switch (param) {
++ case PIN_CONFIG_SKEW_DELAY:
++ if (arg > 0xf)
++ return -EINVAL;
++ conf = gemini_get_pin_conf(pmx, pin);
++ if (!conf) {
++ dev_err(pmx->dev,
++ "invalid pin for skew delay %d\n", pin);
++ return -ENOTSUPP;
++ }
++ arg <<= (ffs(conf->mask) - 1);
++ dev_dbg(pmx->dev,
++ "set pin %d to skew delay mask %08x, val %08x\n",
++ pin, conf->mask, arg);
++ regmap_update_bits(pmx->map, conf->reg, conf->mask, arg);
++ break;
++ default:
++ dev_err(pmx->dev, "Invalid config param %04x\n", param);
++ return -ENOTSUPP;
++ }
++ }
++
++ return ret;
++}
++
++static const struct pinconf_ops gemini_pinconf_ops = {
++ .pin_config_get = gemini_pinconf_get,
++ .pin_config_set = gemini_pinconf_set,
++ .is_generic = true,
++};
++
+ static struct pinctrl_desc gemini_pmx_desc = {
+ .name = DRIVER_NAME,
+ .pctlops = &gemini_pctrl_ops,
+ .pmxops = &gemini_pmx_ops,
++ .confops = &gemini_pinconf_ops,
+ .owner = THIS_MODULE,
+ };
+
+@@ -2249,11 +2415,15 @@ static int gemini_pmx_probe(struct platf
+ val &= 0xffff;
+ if (val == 0x3512) {
+ pmx->is_3512 = true;
++ pmx->confs = gemini_confs_3512;
++ pmx->nconfs = ARRAY_SIZE(gemini_confs_3512);
+ gemini_pmx_desc.pins = gemini_3512_pins;
+ gemini_pmx_desc.npins = ARRAY_SIZE(gemini_3512_pins);
+ dev_info(dev, "detected 3512 chip variant\n");
+ } else if (val == 0x3516) {
+ pmx->is_3516 = true;
++ pmx->confs = gemini_confs_3516;
++ pmx->nconfs = ARRAY_SIZE(gemini_confs_3516);
+ gemini_pmx_desc.pins = gemini_3516_pins;
+ gemini_pmx_desc.npins = ARRAY_SIZE(gemini_3516_pins);
+ dev_info(dev, "detected 3516 chip variant\n");
diff --git a/target/linux/gemini/patches-4.14/0007-pinctrl-gemini-Fix-GMAC-groups.patch b/target/linux/gemini/patches-4.14/0007-pinctrl-gemini-Fix-GMAC-groups.patch
new file mode 100644
index 0000000..902168b
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0007-pinctrl-gemini-Fix-GMAC-groups.patch
@@ -0,0 +1,186 @@
+From e7759c44e0c20dd6b5a259300acdc7350ea6dd32 Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Mon, 6 Nov 2017 21:27:34 +0100
+Subject: [PATCH 07/31] pinctrl: gemini: Fix GMAC groups
+
+The GMII groups need to be split across GMAC0 and GMAC1 since
+GMAC0 is always available but GMAC1 masks GPIO2 lines 0-7
+so we might want just one interface out.
+
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+---
+ drivers/pinctrl/pinctrl-gemini.c | 79 +++++++++++++++++++++++++++-------------
+ 1 file changed, 54 insertions(+), 25 deletions(-)
+
+--- a/drivers/pinctrl/pinctrl-gemini.c
++++ b/drivers/pinctrl/pinctrl-gemini.c
+@@ -96,6 +96,13 @@ struct gemini_pin_group {
+ * you are stuck with it.
+ */
+ #define GLOBAL_MISC_CTRL 0x30
++#define GEMINI_GMAC_IOSEL_MASK GENMASK(28, 27)
++/* Not really used */
++#define GEMINI_GMAC_IOSEL_GMAC0_GMII BIT(28)
++/* Activated with GMAC1 */
++#define GEMINI_GMAC_IOSEL_GMAC0_GMAC1_RGMII BIT(27)
++/* This will be the default */
++#define GEMINI_GMAC_IOSEL_GMAC0_RGMII_GMAC1_GPIO2 0
+ #define TVC_CLK_PAD_ENABLE BIT(20)
+ #define PCI_CLK_PAD_ENABLE BIT(17)
+ #define LPC_CLK_PAD_ENABLE BIT(16)
+@@ -109,8 +116,8 @@ struct gemini_pin_group {
+ #define NAND_PADS_DISABLE BIT(2)
+ #define PFLASH_PADS_DISABLE BIT(1)
+ #define SFLASH_PADS_DISABLE BIT(0)
+-#define PADS_MASK (GENMASK(9, 0) | BIT(16) | BIT(17) | BIT(20))
+-#define PADS_MAXBIT 20
++#define PADS_MASK (GENMASK(9, 0) | BIT(16) | BIT(17) | BIT(20) | BIT(27))
++#define PADS_MAXBIT 27
+
+ /* Ordered by bit index */
+ static const char * const gemini_padgroups[] = {
+@@ -516,9 +523,12 @@ static const unsigned int usb_3512_pins[
+ };
+
+ /* GMII, ethernet pins */
+-static const unsigned int gmii_3512_pins[] = {
+- 311, 240, 258, 276, 294, 312, 241, 259, 277, 295, 313, 242, 260, 278, 296,
+- 315, 297, 279, 261, 243, 316, 298, 280, 262, 244, 317, 299, 281
++static const unsigned int gmii_gmac0_3512_pins[] = {
++ 240, 241, 242, 258, 259, 260, 276, 277, 278, 294, 295, 311, 312, 313
++};
++
++static const unsigned int gmii_gmac1_3512_pins[] = {
++ 243, 244, 261, 262, 279, 280, 281, 296, 297, 298, 299, 315, 316, 317
+ };
+
+ static const unsigned int pci_3512_pins[] = {
+@@ -668,10 +678,10 @@ static const unsigned int gpio1c_3512_pi
+ /* The GPIO1D (28-31) pins overlap with LCD and TVC */
+ static const unsigned int gpio1d_3512_pins[] = { 246, 319, 301, 283 };
+
+-/* The GPIO2A (0-3) pins overlap with GMII and extended parallel flash */
++/* The GPIO2A (0-3) pins overlap with GMII GMAC1 and extended parallel flash */
+ static const unsigned int gpio2a_3512_pins[] = { 315, 297, 279, 261 };
+
+-/* The GPIO2B (4-7) pins overlap with GMII, extended parallel flash and LCD */
++/* The GPIO2B (4-7) pins overlap with GMII GMAC1, extended parallel flash and LCD */
+ static const unsigned int gpio2b_3512_pins[] = { 262, 244, 317, 299 };
+
+ /* The GPIO2C (8-31) pins overlap with PCI */
+@@ -738,9 +748,16 @@ static const struct gemini_pin_group gem
+ .num_pins = ARRAY_SIZE(usb_3512_pins),
+ },
+ {
+- .name = "gmiigrp",
+- .pins = gmii_3512_pins,
+- .num_pins = ARRAY_SIZE(gmii_3512_pins),
++ .name = "gmii_gmac0_grp",
++ .pins = gmii_gmac0_3512_pins,
++ .num_pins = ARRAY_SIZE(gmii_gmac0_3512_pins),
++ },
++ {
++ .name = "gmii_gmac1_grp",
++ .pins = gmii_gmac1_3512_pins,
++ .num_pins = ARRAY_SIZE(gmii_gmac1_3512_pins),
++ /* Bring out RGMII on the GMAC1 pins */
++ .value = GEMINI_GMAC_IOSEL_GMAC0_GMAC1_RGMII,
+ },
+ {
+ .name = "pcigrp",
+@@ -954,14 +971,15 @@ static const struct gemini_pin_group gem
+ .name = "gpio2agrp",
+ .pins = gpio2a_3512_pins,
+ .num_pins = ARRAY_SIZE(gpio2a_3512_pins),
+- /* Conflict with GMII and extended parallel flash */
++ .mask = GEMINI_GMAC_IOSEL_GMAC0_GMAC1_RGMII,
++ /* Conflict with GMII GMAC1 and extended parallel flash */
+ },
+ {
+ .name = "gpio2bgrp",
+ .pins = gpio2b_3512_pins,
+ .num_pins = ARRAY_SIZE(gpio2b_3512_pins),
+- /* Conflict with GMII, extended parallel flash and LCD */
+- .mask = LCD_PADS_ENABLE,
++ /* Conflict with GMII GMAC1, extended parallel flash and LCD */
++ .mask = LCD_PADS_ENABLE | GEMINI_GMAC_IOSEL_GMAC0_GMAC1_RGMII,
+ },
+ {
+ .name = "gpio2cgrp",
+@@ -1441,9 +1459,12 @@ static const unsigned int usb_3516_pins[
+ };
+
+ /* GMII, ethernet pins */
+-static const unsigned int gmii_3516_pins[] = {
+- 306, 307, 308, 309, 310, 325, 326, 327, 328, 329, 330, 345, 346, 347,
+- 348, 349, 350, 351, 367, 368, 369, 370, 371, 386, 387, 389, 390, 391
++static const unsigned int gmii_gmac0_3516_pins[] = {
++ 306, 307, 325, 326, 327, 328, 345, 346, 347, 348, 367, 368, 386, 387
++};
++
++static const unsigned int gmii_gmac1_3516_pins[] = {
++ 308, 309, 310, 329, 330, 349, 350, 351, 369, 370, 371, 389, 390, 391
+ };
+
+ static const unsigned int pci_3516_pins[] = {
+@@ -1585,10 +1606,10 @@ static const unsigned int gpio1c_3516_pi
+ /* The GPIO1D (28-31) pins overlap with TVC */
+ static const unsigned int gpio1d_3516_pins[] = { 353, 311, 394, 374 };
+
+-/* The GPIO2A (0-3) pins overlap with GMII and extended parallel flash */
++/* The GPIO2A (0-3) pins overlap with GMII GMAC1 and extended parallel flash */
+ static const unsigned int gpio2a_3516_pins[] = { 308, 369, 389, 329 };
+
+-/* The GPIO2B (4-7) pins overlap with GMII, extended parallel flash and LCD */
++/* The GPIO2B (4-7) pins overlap with GMII GMAC1, extended parallel flash and LCD */
+ static const unsigned int gpio2b_3516_pins[] = { 391, 351, 310, 371 };
+
+ /* The GPIO2C (8-31) pins overlap with PCI */
+@@ -1660,9 +1681,16 @@ static const struct gemini_pin_group gem
+ .num_pins = ARRAY_SIZE(usb_3516_pins),
+ },
+ {
+- .name = "gmiigrp",
+- .pins = gmii_3516_pins,
+- .num_pins = ARRAY_SIZE(gmii_3516_pins),
++ .name = "gmii_gmac0_grp",
++ .pins = gmii_gmac0_3516_pins,
++ .num_pins = ARRAY_SIZE(gmii_gmac0_3516_pins),
++ },
++ {
++ .name = "gmii_gmac1_grp",
++ .pins = gmii_gmac1_3516_pins,
++ .num_pins = ARRAY_SIZE(gmii_gmac1_3516_pins),
++ /* Bring out RGMII on the GMAC1 pins */
++ .value = GEMINI_GMAC_IOSEL_GMAC0_GMAC1_RGMII,
+ },
+ {
+ .name = "pcigrp",
+@@ -1861,14 +1889,15 @@ static const struct gemini_pin_group gem
+ .name = "gpio2agrp",
+ .pins = gpio2a_3516_pins,
+ .num_pins = ARRAY_SIZE(gpio2a_3516_pins),
+- /* Conflict with GMII and extended parallel flash */
++ .mask = GEMINI_GMAC_IOSEL_GMAC0_GMAC1_RGMII,
++ /* Conflict with GMII GMAC1 and extended parallel flash */
+ },
+ {
+ .name = "gpio2bgrp",
+ .pins = gpio2b_3516_pins,
+ .num_pins = ARRAY_SIZE(gpio2b_3516_pins),
+- /* Conflict with GMII, extended parallel flash and LCD */
+- .mask = LCD_PADS_ENABLE,
++ /* Conflict with GMII GMAC1, extended parallel flash and LCD */
++ .mask = LCD_PADS_ENABLE | GEMINI_GMAC_IOSEL_GMAC0_GMAC1_RGMII,
+ },
+ {
+ .name = "gpio2cgrp",
+@@ -1971,7 +2000,7 @@ static const char * const icegrps[] = {
+ static const char * const idegrps[] = { "idegrp" };
+ static const char * const satagrps[] = { "satagrp" };
+ static const char * const usbgrps[] = { "usbgrp" };
+-static const char * const gmiigrps[] = { "gmiigrp" };
++static const char * const gmiigrps[] = { "gmii_gmac0_grp", "gmii_gmac1_grp" };
+ static const char * const pcigrps[] = { "pcigrp" };
+ static const char * const lpcgrps[] = { "lpcgrp" };
+ static const char * const lcdgrps[] = { "lcdgrp" };
diff --git a/target/linux/gemini/patches-4.14/0008-pinctrl-gemini-Fix-missing-pad-descriptions.patch b/target/linux/gemini/patches-4.14/0008-pinctrl-gemini-Fix-missing-pad-descriptions.patch
new file mode 100644
index 0000000..2d7ed83
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0008-pinctrl-gemini-Fix-missing-pad-descriptions.patch
@@ -0,0 +1,27 @@
+From 3f2941cb12a6d6a0ef4e53e0ecb8d2431d352964 Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Mon, 13 Nov 2017 22:36:12 +0100
+Subject: [PATCH 08/31] pinctrl: gemini: Fix missing pad descriptions
+
+A pretty clever static checker found a bug in my patch: I added more
+bits to a bitmask but didn't extend the array indexed to the same
+bitmask.
+
+Fixes: 756a024f3983 ("pinctrl: gemini: Fix GMAC groups")
+Reported-by: Dan Carpenter <dan.carpenter at oracle.com>
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+---
+ drivers/pinctrl/pinctrl-gemini.c | 2 ++
+ 1 file changed, 2 insertions(+)
+
+--- a/drivers/pinctrl/pinctrl-gemini.c
++++ b/drivers/pinctrl/pinctrl-gemini.c
+@@ -136,6 +136,8 @@ static const char * const gemini_padgrou
+ "PCI CLK",
+ NULL, NULL,
+ "TVC CLK",
++ NULL, NULL, NULL, NULL, NULL,
++ "GMAC1",
+ };
+
+ static const struct pinctrl_pin_desc gemini_3512_pins[] = {
diff --git a/target/linux/gemini/patches-4.14/0009-pinctrl-gemini-Add-two-missing-GPIO-groups.patch b/target/linux/gemini/patches-4.14/0009-pinctrl-gemini-Add-two-missing-GPIO-groups.patch
new file mode 100644
index 0000000..46fc102
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0009-pinctrl-gemini-Add-two-missing-GPIO-groups.patch
@@ -0,0 +1,25 @@
+From c25653d045ce86c5ae472258fdaa39a6baaf75eb Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Sun, 19 Nov 2017 10:57:27 +0100
+Subject: [PATCH 09/31] pinctrl: gemini: Add two missing GPIO groups
+
+The 3512 has two more GPIO groups on GPIO area 0, so let's
+make it possible to combine these with the function.
+
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+---
+ drivers/pinctrl/pinctrl-gemini.c | 3 ++-
+ 1 file changed, 2 insertions(+), 1 deletion(-)
+
+--- a/drivers/pinctrl/pinctrl-gemini.c
++++ b/drivers/pinctrl/pinctrl-gemini.c
+@@ -2015,7 +2015,8 @@ static const char * const sflashgrps[] =
+ static const char * const gpio0grps[] = { "gpio0agrp", "gpio0bgrp", "gpio0cgrp",
+ "gpio0dgrp", "gpio0egrp", "gpio0fgrp",
+ "gpio0ggrp", "gpio0hgrp", "gpio0igrp",
+- "gpio0jgrp", "gpio0kgrp" };
++ "gpio0jgrp", "gpio0kgrp", "gpio0lgrp",
++ "gpio0mgrp" };
+ static const char * const gpio1grps[] = { "gpio1agrp", "gpio1bgrp", "gpio1cgrp",
+ "gpio1dgrp" };
+ static const char * const gpio2grps[] = { "gpio2agrp", "gpio2bgrp", "gpio2cgrp" };
diff --git a/target/linux/gemini/patches-4.14/0010-pinctrl-gemini-Fix-usage-of-3512-groups.patch b/target/linux/gemini/patches-4.14/0010-pinctrl-gemini-Fix-usage-of-3512-groups.patch
new file mode 100644
index 0000000..1cab269
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0010-pinctrl-gemini-Fix-usage-of-3512-groups.patch
@@ -0,0 +1,25 @@
+From 88a5c6ad311588f178c5a88e4eeacc6d40b8ede3 Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Wed, 22 Nov 2017 21:04:14 +0100
+Subject: [PATCH 10/31] pinctrl: gemini: Fix usage of 3512 groups
+
+The pin config lookup function was still hardcoding the
+3516 pin set, which is obviously wrong. Use the pointer
+in the state container.
+
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+---
+ drivers/pinctrl/pinctrl-gemini.c | 2 +-
+ 1 file changed, 1 insertion(+), 1 deletion(-)
+
+--- a/drivers/pinctrl/pinctrl-gemini.c
++++ b/drivers/pinctrl/pinctrl-gemini.c
+@@ -2323,7 +2323,7 @@ static const struct gemini_pin_conf *gem
+ int i;
+
+ for (i = 0; i < pmx->nconfs; i++) {
+- retconf = &gemini_confs_3516[i];
++ retconf = &pmx->confs[i];
+ if (retconf->pin == pin)
+ return retconf;
+ }
diff --git a/target/linux/gemini/patches-4.14/0011-pinctrl-gemini-Support-drive-strength-setting.patch b/target/linux/gemini/patches-4.14/0011-pinctrl-gemini-Support-drive-strength-setting.patch
new file mode 100644
index 0000000..5fefece
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0011-pinctrl-gemini-Support-drive-strength-setting.patch
@@ -0,0 +1,198 @@
+From f147cf49ef39f5e87d5df9ef1fab52683bc75c63 Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Sat, 2 Dec 2017 12:23:09 +0100
+Subject: [PATCH 11/31] pinctrl: gemini: Support drive strength setting
+
+The Gemini pin controller can set drive strength for a few
+select groups of pins (not individually). Implement this
+for GMAC0 and 1 (ethernet ports), IDE and PCI.
+
+Cc: devicetree at vger.kernel.org
+Reviewed-by: Rob Herring <robh at kernel.org>
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+---
+ .../bindings/pinctrl/cortina,gemini-pinctrl.txt | 3 +
+ drivers/pinctrl/pinctrl-gemini.c | 81 ++++++++++++++++++++++
+ 2 files changed, 84 insertions(+)
+
+--- a/Documentation/devicetree/bindings/pinctrl/cortina,gemini-pinctrl.txt
++++ b/Documentation/devicetree/bindings/pinctrl/cortina,gemini-pinctrl.txt
+@@ -17,6 +17,9 @@ and generic pin config nodes.
+
+ Supported configurations:
+ - skew-delay is supported on the Ethernet pins
++- drive-strength with 4, 8, 12 or 16 mA as argument is supported for
++ entire groups on the groups "idegrp", "gmii_gmac0_grp", "gmii_gmac1_grp"
++ and "pcigrp".
+
+ Example:
+
+--- a/drivers/pinctrl/pinctrl-gemini.c
++++ b/drivers/pinctrl/pinctrl-gemini.c
+@@ -67,6 +67,9 @@ struct gemini_pmx {
+ * elements in .pins so we can iterate over that array
+ * @mask: bits to clear to enable this when doing pin muxing
+ * @value: bits to set to enable this when doing pin muxing
++ * @driving_mask: bitmask for the IO Pad driving register for this
++ * group, if it supports altering the driving strength of
++ * its lines.
+ */
+ struct gemini_pin_group {
+ const char *name;
+@@ -74,12 +77,14 @@ struct gemini_pin_group {
+ const unsigned int num_pins;
+ u32 mask;
+ u32 value;
++ u32 driving_mask;
+ };
+
+ /* Some straight-forward control registers */
+ #define GLOBAL_WORD_ID 0x00
+ #define GLOBAL_STATUS 0x04
+ #define GLOBAL_STATUS_FLPIN BIT(20)
++#define GLOBAL_IODRIVE 0x10
+ #define GLOBAL_GMAC_CTRL_SKEW 0x1c
+ #define GLOBAL_GMAC0_DATA_SKEW 0x20
+ #define GLOBAL_GMAC1_DATA_SKEW 0x24
+@@ -738,6 +743,7 @@ static const struct gemini_pin_group gem
+ /* Conflict with all flash usage */
+ .value = IDE_PADS_ENABLE | NAND_PADS_DISABLE |
+ PFLASH_PADS_DISABLE | SFLASH_PADS_DISABLE,
++ .driving_mask = GENMASK(21, 20),
+ },
+ {
+ .name = "satagrp",
+@@ -753,6 +759,7 @@ static const struct gemini_pin_group gem
+ .name = "gmii_gmac0_grp",
+ .pins = gmii_gmac0_3512_pins,
+ .num_pins = ARRAY_SIZE(gmii_gmac0_3512_pins),
++ .driving_mask = GENMASK(17, 16),
+ },
+ {
+ .name = "gmii_gmac1_grp",
+@@ -760,6 +767,7 @@ static const struct gemini_pin_group gem
+ .num_pins = ARRAY_SIZE(gmii_gmac1_3512_pins),
+ /* Bring out RGMII on the GMAC1 pins */
+ .value = GEMINI_GMAC_IOSEL_GMAC0_GMAC1_RGMII,
++ .driving_mask = GENMASK(19, 18),
+ },
+ {
+ .name = "pcigrp",
+@@ -767,6 +775,7 @@ static const struct gemini_pin_group gem
+ .num_pins = ARRAY_SIZE(pci_3512_pins),
+ /* Conflict only with GPIO2 */
+ .value = PCI_PADS_ENABLE | PCI_CLK_PAD_ENABLE,
++ .driving_mask = GENMASK(23, 22),
+ },
+ {
+ .name = "lpcgrp",
+@@ -1671,6 +1680,7 @@ static const struct gemini_pin_group gem
+ /* Conflict with all flash usage */
+ .value = IDE_PADS_ENABLE | NAND_PADS_DISABLE |
+ PFLASH_PADS_DISABLE | SFLASH_PADS_DISABLE,
++ .driving_mask = GENMASK(21, 20),
+ },
+ {
+ .name = "satagrp",
+@@ -1686,6 +1696,7 @@ static const struct gemini_pin_group gem
+ .name = "gmii_gmac0_grp",
+ .pins = gmii_gmac0_3516_pins,
+ .num_pins = ARRAY_SIZE(gmii_gmac0_3516_pins),
++ .driving_mask = GENMASK(17, 16),
+ },
+ {
+ .name = "gmii_gmac1_grp",
+@@ -1693,6 +1704,7 @@ static const struct gemini_pin_group gem
+ .num_pins = ARRAY_SIZE(gmii_gmac1_3516_pins),
+ /* Bring out RGMII on the GMAC1 pins */
+ .value = GEMINI_GMAC_IOSEL_GMAC0_GMAC1_RGMII,
++ .driving_mask = GENMASK(19, 18),
+ },
+ {
+ .name = "pcigrp",
+@@ -1700,6 +1712,7 @@ static const struct gemini_pin_group gem
+ .num_pins = ARRAY_SIZE(pci_3516_pins),
+ /* Conflict only with GPIO2 */
+ .value = PCI_PADS_ENABLE | PCI_CLK_PAD_ENABLE,
++ .driving_mask = GENMASK(23, 22),
+ },
+ {
+ .name = "lpcgrp",
+@@ -2394,9 +2407,77 @@ static int gemini_pinconf_set(struct pin
+ return ret;
+ }
+
++static int gemini_pinconf_group_set(struct pinctrl_dev *pctldev,
++ unsigned selector,
++ unsigned long *configs,
++ unsigned num_configs)
++{
++ struct gemini_pmx *pmx = pinctrl_dev_get_drvdata(pctldev);
++ const struct gemini_pin_group *grp = NULL;
++ enum pin_config_param param;
++ u32 arg;
++ u32 val;
++ int i;
++
++ if (pmx->is_3512)
++ grp = &gemini_3512_pin_groups[selector];
++ if (pmx->is_3516)
++ grp = &gemini_3516_pin_groups[selector];
++
++ /* First figure out if this group supports configs */
++ if (!grp->driving_mask) {
++ dev_err(pmx->dev, "pin config group \"%s\" does "
++ "not support drive strength setting\n",
++ grp->name);
++ return -EINVAL;
++ }
++
++ for (i = 0; i < num_configs; i++) {
++ param = pinconf_to_config_param(configs[i]);
++ arg = pinconf_to_config_argument(configs[i]);
++
++ switch (param) {
++ case PIN_CONFIG_DRIVE_STRENGTH:
++ switch (arg) {
++ case 4:
++ val = 0;
++ break;
++ case 8:
++ val = 1;
++ break;
++ case 12:
++ val = 2;
++ break;
++ case 16:
++ val = 3;
++ break;
++ default:
++ dev_err(pmx->dev,
++ "invalid drive strength %d mA\n",
++ arg);
++ return -ENOTSUPP;
++ }
++ val <<= (ffs(grp->driving_mask) - 1);
++ regmap_update_bits(pmx->map, GLOBAL_IODRIVE,
++ grp->driving_mask,
++ val);
++ dev_info(pmx->dev,
++ "set group %s to %d mA drive strength mask %08x val %08x\n",
++ grp->name, arg, grp->driving_mask, val);
++ break;
++ default:
++ dev_err(pmx->dev, "invalid config param %04x\n", param);
++ return -ENOTSUPP;
++ }
++ }
++
++ return 0;
++}
++
+ static const struct pinconf_ops gemini_pinconf_ops = {
+ .pin_config_get = gemini_pinconf_get,
+ .pin_config_set = gemini_pinconf_set,
++ .pin_config_group_set = gemini_pinconf_group_set,
+ .is_generic = true,
+ };
+
diff --git a/target/linux/gemini/patches-4.14/0012-ARM-dts-Add-ethernet-PHYs-to-the-a-bunch-of-Geminis.patch b/target/linux/gemini/patches-4.14/0012-ARM-dts-Add-ethernet-PHYs-to-the-a-bunch-of-Geminis.patch
new file mode 100644
index 0000000..db701e3
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0012-ARM-dts-Add-ethernet-PHYs-to-the-a-bunch-of-Geminis.patch
@@ -0,0 +1,113 @@
+From f0674df220f3da81c173025636a904b395cf8f8b Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Sun, 19 Nov 2017 10:46:16 +0100
+Subject: [PATCH 12/31] ARM: dts: Add ethernet PHYs to the a bunch of Geminis
+
+These Gemini boards have Ethernet PHY on GPIO bit-banged
+MDIO, clearly defined in the corresponding OpenWRT
+ethernet patches since ages. Add them in accordance with
+the OpenWRT patch so we can use them when we add ethernet
+support.
+
+Reviewed-by: Andrew Lunn <andrew at lunn.ch>
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+---
+ arch/arm/boot/dts/gemini-nas4220b.dts | 13 +++++++++++++
+ arch/arm/boot/dts/gemini-rut1xx.dts | 13 +++++++++++++
+ arch/arm/boot/dts/gemini-wbd111.dts | 13 +++++++++++++
+ arch/arm/boot/dts/gemini-wbd222.dts | 18 ++++++++++++++++++
+ 4 files changed, 57 insertions(+)
+
+--- a/arch/arm/boot/dts/gemini-nas4220b.dts
++++ b/arch/arm/boot/dts/gemini-nas4220b.dts
+@@ -64,6 +64,19 @@
+ };
+ };
+
++ mdio0: ethernet-phy {
++ compatible = "virtual,mdio-gpio";
++ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
++ <&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ phy0: ethernet-phy at 1 {
++ reg = <1>;
++ device_type = "ethernet-phy";
++ };
++ };
++
+ soc {
+ flash at 30000000 {
+ status = "okay";
+--- a/arch/arm/boot/dts/gemini-rut1xx.dts
++++ b/arch/arm/boot/dts/gemini-rut1xx.dts
+@@ -58,6 +58,19 @@
+ };
+ };
+
++ mdio0: ethernet-phy {
++ compatible = "virtual,mdio-gpio";
++ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
++ <&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ phy0: ethernet-phy at 1 {
++ reg = <1>;
++ device_type = "ethernet-phy";
++ };
++ };
++
+ soc {
+ flash at 30000000 {
+ status = "okay";
+--- a/arch/arm/boot/dts/gemini-wbd111.dts
++++ b/arch/arm/boot/dts/gemini-wbd111.dts
+@@ -69,6 +69,19 @@
+ };
+ };
+
++ mdio0: ethernet-phy {
++ compatible = "virtual,mdio-gpio";
++ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
++ <&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ phy0: ethernet-phy at 1 {
++ reg = <1>;
++ device_type = "ethernet-phy";
++ };
++ };
++
+ soc {
+ flash at 30000000 {
+ status = "okay";
+--- a/arch/arm/boot/dts/gemini-wbd222.dts
++++ b/arch/arm/boot/dts/gemini-wbd222.dts
+@@ -69,6 +69,24 @@
+ };
+ };
+
++ mdio0: ethernet-phy {
++ compatible = "virtual,mdio-gpio";
++ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
++ <&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ phy0: ethernet-phy at 1 {
++ reg = <1>;
++ device_type = "ethernet-phy";
++ };
++
++ phy1: ethernet-phy at 3 {
++ reg = <3>;
++ device_type = "ethernet-phy";
++ };
++ };
++
+ soc {
+ flash at 30000000 {
+ status = "okay";
diff --git a/target/linux/gemini/patches-4.14/0013-ARM-dts-Add-basic-devicetree-for-D-Link-DNS-313.patch b/target/linux/gemini/patches-4.14/0013-ARM-dts-Add-basic-devicetree-for-D-Link-DNS-313.patch
new file mode 100644
index 0000000..cdf25a9
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0013-ARM-dts-Add-basic-devicetree-for-D-Link-DNS-313.patch
@@ -0,0 +1,272 @@
+From 2f08de94f207a4347053e1faa22c9a310c9c61b0 Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Fri, 17 Nov 2017 16:36:32 +0100
+Subject: [PATCH 13/31] ARM: dts: Add basic devicetree for D-Link DNS-313
+
+This adds a basic device tree for the D-Link DNS-313
+NAS enclosure. This device has a thermal sensor and a
+fan so we add a thermal zone for the chassis in the
+device tree based on information from the product.
+
+Reviewed-by: Andrew Lunn <andrew at lunn.ch>
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+---
+ arch/arm/boot/dts/Makefile | 1 +
+ arch/arm/boot/dts/gemini-dlink-dns-313.dts | 241 +++++++++++++++++++++++++++++
+ 2 files changed, 242 insertions(+)
+ create mode 100644 arch/arm/boot/dts/gemini-dlink-dns-313.dts
+
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -185,6 +185,7 @@ dtb-$(CONFIG_ARCH_EXYNOS5) += \
+ exynos5800-peach-pi.dtb
+ dtb-$(CONFIG_ARCH_GEMINI) += \
+ gemini-dlink-dir-685.dtb \
++ gemini-dlink-dns-313.dtb \
+ gemini-nas4220b.dtb \
+ gemini-rut1xx.dtb \
+ gemini-sq201.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/gemini-dlink-dns-313.dts
+@@ -0,0 +1,241 @@
++// SPDX-License-Identifier: GPL-2.0
++/*
++ * Device Tree file for D-Link DNS-313 1-Bay Network Storage Enclosure
++ */
++
++/dts-v1/;
++
++#include "gemini.dtsi"
++#include <dt-bindings/input/input.h>
++#include <dt-bindings/thermal/thermal.h>
++
++/ {
++ model = "D-Link DNS-313 1-Bay Network Storage Enclosure";
++ compatible = "dlink,dir-313", "cortina,gemini";
++ #address-cells = <1>;
++ #size-cells = <1>;
++
++ memory {
++ /* 64 MB SDRAM in a Nanya NT5DS32M16BS-6K package */
++ device_type = "memory";
++ reg = <0x00000000 0x4000000>;
++ };
++
++ aliases {
++ mdio-gpio0 = &mdio0;
++ };
++
++ chosen {
++ stdout-path = "uart0:19200n8";
++ };
++
++ gpio_keys {
++ compatible = "gpio-keys";
++ #address-cells = <1>;
++ #size-cells = <0>;
++ button-esc {
++ debounce_interval = <50>;
++ wakeup-source;
++ linux,code = <KEY_ESC>;
++ label = "reset";
++ gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
++ };
++ };
++
++ leds {
++ compatible = "gpio-leds";
++ led-power {
++ label = "dns313:blue:power";
++ gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
++ default-state = "on";
++ linux,default-trigger = "heartbeat";
++ };
++ led-disk-blue {
++ label = "dns313:blue:disk";
++ gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
++ default-state = "off";
++ };
++ led-disk-green {
++ label = "dns313:green:disk";
++ gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>;
++ default-state = "off";
++ linux,default-trigger = "ide-disk";
++ /* Ideally should activate while reading */
++ };
++ led-disk-red {
++ label = "dns313:red:disk";
++ gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
++ default-state = "off";
++ /* Ideally should activate while writing */
++ };
++ };
++
++ /*
++ * This is a ADDA AD0405GB-G73 fan @3000 and 6000 RPM.
++ */
++ fan0: gpio-fan {
++ compatible = "gpio-fan";
++ gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>,
++ <&gpio0 12 GPIO_ACTIVE_HIGH>;
++ gpio-fan,speed-map = <0 0>, <3000 1>, <6000 2>;
++ cooling-min-level = <0>;
++ cooling-max-level = <2>;
++ #cooling-cells = <2>;
++ };
++
++
++ /* Global Mixed-Mode Technology G751 mounted on GPIO I2C */
++ gpio-i2c {
++ compatible = "i2c-gpio";
++ sda-gpios = <&gpio0 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
++ scl-gpios = <&gpio0 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ g751: temperature-sensor at 48 {
++ compatible = "gmt,g751";
++ reg = <0x48>;
++ #thermal-sensor-cells = <0>;
++ };
++ };
++
++ thermal-zones {
++ chassis-thermal {
++ /* Poll every 20 seconds */
++ polling-delay = <20000>;
++ /* Poll every 2nd second when cooling */
++ polling-delay-passive = <2000>;
++
++ thermal-sensors = <&g751>;
++
++ /* Tripping points from the fan.script in the rootfs */
++ trips {
++ chassis_alert0: chassis-alert0 {
++ /* At 43 degrees turn on low speed */
++ temperature = <43000>;
++ hysteresis = <3000>;
++ type = "active";
++ };
++ chassis_alert1: chassis-alert1 {
++ /* At 47 degrees turn on high speed */
++ temperature = <47000>;
++ hysteresis = <3000>;
++ type = "active";
++ };
++ chassis_crit: chassis-crit {
++ /* Just shut down at 60 degrees */
++ temperature = <60000>;
++ hysteresis = <2000>;
++ type = "critical";
++ };
++ };
++
++ cooling-maps {
++ map0 {
++ trip = <&chassis_alert0>;
++ cooling-device = <&fan0 1 1>;
++ };
++ map1 {
++ trip = <&chassis_alert1>;
++ cooling-device = <&fan0 2 2>;
++ };
++ };
++ };
++ };
++
++ mdio0: ethernet-phy {
++ compatible = "virtual,mdio-gpio";
++ /* Uses MDC and MDIO */
++ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
++ <&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ /* This is a Realtek RTL8211B Gigabit ethernet transceiver */
++ phy0: ethernet-phy at 1 {
++ reg = <1>;
++ device_type = "ethernet-phy";
++ };
++ };
++
++ soc {
++ flash at 30000000 {
++ status = "okay";
++ /* 512KB of flash */
++ reg = <0x30000000 0x00080000>;
++
++ /*
++ * This "RedBoot" is the Storlink derivative.
++ */
++ partition at 0 {
++ label = "RedBoot";
++ reg = <0x00000000 0x00040000>;
++ read-only;
++ };
++ partition at 40000 {
++ label = "MTD1";
++ reg = <0x00040000 0x00020000>;
++ read-only;
++ };
++ partition at 60000 {
++ label = "MTD2";
++ reg = <0x00060000 0x00020000>;
++ read-only;
++ };
++ };
++
++ syscon: syscon at 40000000 {
++ pinctrl {
++ /*
++ */
++ gpio0_default_pins: pinctrl-gpio0 {
++ mux {
++ function = "gpio0";
++ groups =
++ /* Used by LEDs conflicts ICE */
++ "gpio0bgrp",
++ /* Used by ? conflicts ICE */
++ "gpio0cgrp",
++ /*
++ * Used by fan & G751, conflicts LPC,
++ * UART modem lines, SSP
++ */
++ "gpio0egrp",
++ /* Used by G751 */
++ "gpio0fgrp",
++ /* Used by MDIO */
++ "gpio0igrp";
++ };
++ };
++ gpio1_default_pins: pinctrl-gpio1 {
++ mux {
++ function = "gpio1";
++ /* Used by "reset" button */
++ groups = "gpio1dgrp";
++ };
++ };
++ };
++ };
++
++ sata: sata at 46000000 {
++ /* The ROM uses this muxmode */
++ cortina,gemini-ata-muxmode = <3>;
++ cortina,gemini-enable-sata-bridge;
++ status = "okay";
++ };
++
++ gpio0: gpio at 4d000000 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&gpio0_default_pins>;
++ };
++
++ gpio1: gpio at 4e000000 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&gpio1_default_pins>;
++ };
++
++ ata at 63000000 {
++ status = "okay";
++ };
++ };
++};
diff --git a/target/linux/gemini/patches-4.14/0014-ARM-dts-Flags-D-Link-DIR-685-I2C-bus-gpios.patch b/target/linux/gemini/patches-4.14/0014-ARM-dts-Flags-D-Link-DIR-685-I2C-bus-gpios.patch
new file mode 100644
index 0000000..5cefd18
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0014-ARM-dts-Flags-D-Link-DIR-685-I2C-bus-gpios.patch
@@ -0,0 +1,27 @@
+From eed839dc713fdb7b2579dbfea41d676386b8259b Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Sun, 10 Sep 2017 20:02:33 +0200
+Subject: [PATCH 14/31] ARM: dts: Flags D-Link DIR-685 I2C bus gpios
+
+These GPIOs are used in open drain mode, so make sure to
+flag them as such. Use the new separate scl/sda line
+GPIO bindings.
+
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+---
+ arch/arm/boot/dts/gemini-dlink-dir-685.dts | 4 ++--
+ 1 file changed, 2 insertions(+), 2 deletions(-)
+
+--- a/arch/arm/boot/dts/gemini-dlink-dir-685.dts
++++ b/arch/arm/boot/dts/gemini-dlink-dir-685.dts
+@@ -99,8 +99,8 @@
+ gpio-i2c {
+ compatible = "i2c-gpio";
+ /* Collides with ICE */
+- gpios = <&gpio0 5 0>, /* SDA */
+- <&gpio0 6 0>; /* SCL */
++ sda-gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
++ scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
diff --git a/target/linux/gemini/patches-4.14/0015-ARM-dts-Add-PCI-to-WBD111-and-WBD222.patch b/target/linux/gemini/patches-4.14/0015-ARM-dts-Add-PCI-to-WBD111-and-WBD222.patch
new file mode 100644
index 0000000..429625e
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0015-ARM-dts-Add-PCI-to-WBD111-and-WBD222.patch
@@ -0,0 +1,74 @@
+From dec551d2301f71a692ed1729a323c8259d36f849 Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Wed, 11 Oct 2017 19:49:13 +0200
+Subject: [PATCH 15/31] ARM: dts: Add PCI to WBD111 and WBD222
+
+These two boards have mini-PCI card slots, so enable PCI
+on both of them.
+
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+---
+ arch/arm/boot/dts/gemini-wbd111.dts | 22 ++++++++++++++++++++++
+ arch/arm/boot/dts/gemini-wbd222.dts | 22 ++++++++++++++++++++++
+ 2 files changed, 44 insertions(+)
+
+--- a/arch/arm/boot/dts/gemini-wbd111.dts
++++ b/arch/arm/boot/dts/gemini-wbd111.dts
+@@ -138,5 +138,27 @@
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio0_default_pins>;
+ };
++
++ pci at 50000000 {
++ status = "okay";
++ interrupt-map-mask = <0xf800 0 0 7>;
++ interrupt-map =
++ <0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
++ <0x4800 0 0 2 &pci_intc 1>,
++ <0x4800 0 0 3 &pci_intc 2>,
++ <0x4800 0 0 4 &pci_intc 3>,
++ <0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
++ <0x5000 0 0 2 &pci_intc 2>,
++ <0x5000 0 0 3 &pci_intc 3>,
++ <0x5000 0 0 4 &pci_intc 0>,
++ <0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
++ <0x5800 0 0 2 &pci_intc 3>,
++ <0x5800 0 0 3 &pci_intc 0>,
++ <0x5800 0 0 4 &pci_intc 1>,
++ <0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
++ <0x6000 0 0 2 &pci_intc 0>,
++ <0x6000 0 0 3 &pci_intc 1>,
++ <0x6000 0 0 4 &pci_intc 2>;
++ };
+ };
+ };
+--- a/arch/arm/boot/dts/gemini-wbd222.dts
++++ b/arch/arm/boot/dts/gemini-wbd222.dts
+@@ -143,5 +143,27 @@
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio0_default_pins>;
+ };
++
++ pci at 50000000 {
++ status = "okay";
++ interrupt-map-mask = <0xf800 0 0 7>;
++ interrupt-map =
++ <0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
++ <0x4800 0 0 2 &pci_intc 1>,
++ <0x4800 0 0 3 &pci_intc 2>,
++ <0x4800 0 0 4 &pci_intc 3>,
++ <0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
++ <0x5000 0 0 2 &pci_intc 2>,
++ <0x5000 0 0 3 &pci_intc 3>,
++ <0x5000 0 0 4 &pci_intc 0>,
++ <0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
++ <0x5800 0 0 2 &pci_intc 3>,
++ <0x5800 0 0 3 &pci_intc 0>,
++ <0x5800 0 0 4 &pci_intc 1>,
++ <0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
++ <0x6000 0 0 2 &pci_intc 0>,
++ <0x6000 0 0 3 &pci_intc 1>,
++ <0x6000 0 0 4 &pci_intc 2>;
++ };
+ };
+ };
diff --git a/target/linux/gemini/patches-4.14/0016-ARM-dts-Add-TVE-TVC-and-ILI9322-panel-to-DIR-685.patch b/target/linux/gemini/patches-4.14/0016-ARM-dts-Add-TVE-TVC-and-ILI9322-panel-to-DIR-685.patch
new file mode 100644
index 0000000..e0cf267
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0016-ARM-dts-Add-TVE-TVC-and-ILI9322-panel-to-DIR-685.patch
@@ -0,0 +1,113 @@
+From 9d3b968d13ba1eecaf22d5824cf8fd270c061534 Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Sat, 15 Jul 2017 21:02:06 +0200
+Subject: [PATCH 16/31] ARM: dts: Add TVE/TVC and ILI9322 panel to DIR-685
+
+This adds the TVE200/TVC TV-encoder and the Ilitek ILI9322 panel
+to the DIR-685 device tree.
+
+This brings graphics to this funky router and it is possible to
+even run a console on its tiny screen.
+
+Incidentally this requires us to disable the access to the
+parallel (NOR) flash, as the communication pins to the panel
+are shared with the flash memory.
+
+To access the flash, a separate kernel with the panel disabled
+and the flash enabled should be booted. The pin control selecting
+whether to use the lines cannot be altered at runtime due to
+hardware constraints.
+
+Cc: David Lechner <david at lechnology.com>
+Cc: Stefano Babic <sbabic at denx.de>
+Cc: Ben Dooks <ben.dooks at codethink.co.uk>
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+---
+ arch/arm/boot/dts/gemini-dlink-dir-685.dts | 63 +++++++++++++++++++++++++++++-
+ 1 file changed, 62 insertions(+), 1 deletion(-)
+
+--- a/arch/arm/boot/dts/gemini-dlink-dir-685.dts
++++ b/arch/arm/boot/dts/gemini-dlink-dir-685.dts
+@@ -45,6 +45,47 @@
+ };
+ };
+
++ vdisp: regulator {
++ compatible = "regulator-fixed";
++ regulator-name = "display-power";
++ regulator-min-microvolt = <3600000>;
++ regulator-max-microvolt = <3600000>;
++ /* Collides with LCD E */
++ gpio = <&gpio0 16 GPIO_ACTIVE_HIGH>;
++ enable-active-high;
++ };
++
++ spi {
++ compatible = "spi-gpio";
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ /* Collides with IDE pins, that's cool (we do not use them) */
++ gpio-sck = <&gpio1 5 GPIO_ACTIVE_HIGH>;
++ gpio-miso = <&gpio1 8 GPIO_ACTIVE_HIGH>;
++ gpio-mosi = <&gpio1 7 GPIO_ACTIVE_HIGH>;
++ /* Collides with pflash CE1, not so cool */
++ cs-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
++ num-chipselects = <1>;
++
++ panel: display at 0 {
++ compatible = "dlink,dir-685-panel", "ilitek,ili9322";
++ reg = <0>;
++ /* 50 ns min period = 20 MHz */
++ spi-max-frequency = <20000000>;
++ spi-cpol; /* Clock active low */
++ vcc-supply = <&vdisp>;
++ iovcc-supply = <&vdisp>;
++ vci-supply = <&vdisp>;
++
++ port {
++ panel_in: endpoint {
++ remote-endpoint = <&display_out>;
++ };
++ };
++ };
++ };
++
+ leds {
+ compatible = "gpio-leds";
+ led-wps {
+@@ -115,7 +156,16 @@
+
+ soc {
+ flash at 30000000 {
+- status = "okay";
++ /*
++ * Flash access is by default disabled, because it
++ * collides with the Chip Enable signal for the display
++ * panel, that reuse the parallel flash Chip Select 1
++ * (CS1). Enabling flash makes graphics stop working.
++ *
++ * We might be able to hack around this by letting
++ * GPIO poke around in the flash controller registers.
++ */
++ /* status = "okay"; */
+ /* 32MB of flash */
+ reg = <0x30000000 0x02000000>;
+
+@@ -242,5 +292,16 @@
+ ata at 63000000 {
+ status = "okay";
+ };
++
++ display-controller at 6a000000 {
++ status = "okay";
++
++ port at 0 {
++ reg = <0>;
++ display_out: endpoint {
++ remote-endpoint = <&panel_in>;
++ };
++ };
++ };
+ };
+ };
diff --git a/target/linux/gemini/patches-4.14/0017-watchdog-gemini-ftwdt010-rename-DT-bindings.patch b/target/linux/gemini/patches-4.14/0017-watchdog-gemini-ftwdt010-rename-DT-bindings.patch
new file mode 100644
index 0000000..3fe0b8f
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0017-watchdog-gemini-ftwdt010-rename-DT-bindings.patch
@@ -0,0 +1,88 @@
+From d73f6cc09bcbe258a72c06899215d1a3e8a7686d Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Mon, 16 Oct 2017 22:54:23 +0200
+Subject: [PATCH 17/31] watchdog: gemini/ftwdt010: rename DT bindings
+
+The device tree bindings are in two copies and also should be
+consolidated into a single Faraday Technology FTWDT010
+binding since we uncovered that this IP part is a standard
+IP from Faraday.
+
+Cc: devicetree at vger.kernel.org
+Acked-by: Rob Herring <robh at kernel.org>
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+Reviewed-by: Guenter Roeck <linux at roeck-us.net>
+Signed-off-by: Guenter Roeck <linux at roeck-us.net>
+Signed-off-by: Wim Van Sebroeck <wim at iguana.be>
+---
+ .../bindings/watchdog/cortina,gemini-watchdog.txt | 17 -----------------
+ ...{cortina,gemin-watchdog.txt => faraday,ftwdt010.txt} | 11 ++++++++---
+ 2 files changed, 8 insertions(+), 20 deletions(-)
+ delete mode 100644 Documentation/devicetree/bindings/watchdog/cortina,gemini-watchdog.txt
+ rename Documentation/devicetree/bindings/watchdog/{cortina,gemin-watchdog.txt => faraday,ftwdt010.txt} (55%)
+
+--- a/Documentation/devicetree/bindings/watchdog/cortina,gemini-watchdog.txt
++++ /dev/null
+@@ -1,17 +0,0 @@
+-Cortina Systems Gemini SoC Watchdog
+-
+-Required properties:
+-- compatible : must be "cortina,gemini-watchdog"
+-- reg : shall contain base register location and length
+-- interrupts : shall contain the interrupt for the watchdog
+-
+-Optional properties:
+-- timeout-sec : the default watchdog timeout in seconds.
+-
+-Example:
+-
+-watchdog at 41000000 {
+- compatible = "cortina,gemini-watchdog";
+- reg = <0x41000000 0x1000>;
+- interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
+-};
+--- a/Documentation/devicetree/bindings/watchdog/cortina,gemin-watchdog.txt
++++ /dev/null
+@@ -1,17 +0,0 @@
+-Cortina Systems Gemini SoC Watchdog
+-
+-Required properties:
+-- compatible : must be "cortina,gemini-watchdog"
+-- reg : shall contain base register location and length
+-- interrupts : shall contain the interrupt for the watchdog
+-
+-Optional properties:
+-- timeout-sec : the default watchdog timeout in seconds.
+-
+-Example:
+-
+-watchdog at 41000000 {
+- compatible = "cortina,gemini-watchdog";
+- reg = <0x41000000 0x1000>;
+- interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
+-};
+--- /dev/null
++++ b/Documentation/devicetree/bindings/watchdog/faraday,ftwdt010.txt
+@@ -0,0 +1,22 @@
++Faraday Technology FTWDT010 watchdog
++
++This is an IP part from Faraday Technology found in the Gemini
++SoCs and others.
++
++Required properties:
++- compatible : must be one of
++ "faraday,ftwdt010"
++ "cortina,gemini-watchdog", "faraday,ftwdt010"
++- reg : shall contain base register location and length
++- interrupts : shall contain the interrupt for the watchdog
++
++Optional properties:
++- timeout-sec : the default watchdog timeout in seconds.
++
++Example:
++
++watchdog at 41000000 {
++ compatible = "faraday,ftwdt010";
++ reg = <0x41000000 0x1000>;
++ interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
++};
diff --git a/target/linux/gemini/patches-4.14/0018-watchdog-gemini-ftwdt010-rename-driver-and-symbols.patch b/target/linux/gemini/patches-4.14/0018-watchdog-gemini-ftwdt010-rename-driver-and-symbols.patch
new file mode 100644
index 0000000..23c1989
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0018-watchdog-gemini-ftwdt010-rename-driver-and-symbols.patch
@@ -0,0 +1,527 @@
+From c197a5a04d658da490de08636066a6bdbebf16c5 Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Mon, 16 Oct 2017 22:54:24 +0200
+Subject: [PATCH 18/31] watchdog: gemini/ftwdt010: rename driver and symbols
+
+This renames all the driver files and symbols for the Gemini
+watchdog to FTWDT010 as it has been revealed that this IP block
+is a generic watchdog timer from Faraday Technology used in
+several SoC designs.
+
+Select this driver by default for the Gemini, it is a sensible
+driver to always have enabled.
+
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+Reviewed-by: Guenter Roeck <linux at roeck-us.net>
+Signed-off-by: Guenter Roeck <linux at roeck-us.net>
+Signed-off-by: Wim Van Sebroeck <wim at iguana.be>
+---
+ drivers/watchdog/Kconfig | 14 +--
+ drivers/watchdog/Makefile | 2 +-
+ drivers/watchdog/{gemini_wdt.c => ftwdt010_wdt.c} | 117 +++++++++++-----------
+ 3 files changed, 68 insertions(+), 65 deletions(-)
+ rename drivers/watchdog/{gemini_wdt.c => ftwdt010_wdt.c} (50%)
+
+--- a/drivers/watchdog/Kconfig
++++ b/drivers/watchdog/Kconfig
+@@ -321,16 +321,18 @@ config 977_WATCHDOG
+
+ Not sure? It's safe to say N.
+
+-config GEMINI_WATCHDOG
+- tristate "Gemini watchdog"
+- depends on ARCH_GEMINI
++config FTWDT010_WATCHDOG
++ tristate "Faraday Technology FTWDT010 watchdog"
++ depends on ARM || COMPILE_TEST
+ select WATCHDOG_CORE
++ default ARCH_GEMINI
+ help
+- Say Y here if to include support for the watchdog timer
+- embedded in the Cortina Systems Gemini family of devices.
++ Say Y here if to include support for the Faraday Technology
++ FTWDT010 watchdog timer embedded in the Cortina Systems Gemini
++ family of devices.
+
+ To compile this driver as a module, choose M here: the
+- module will be called gemini_wdt.
++ module will be called ftwdt010_wdt.
+
+ config IXP4XX_WATCHDOG
+ tristate "IXP4xx Watchdog"
+--- a/drivers/watchdog/Makefile
++++ b/drivers/watchdog/Makefile
+@@ -46,7 +46,7 @@ obj-$(CONFIG_OMAP_WATCHDOG) += omap_wdt.
+ obj-$(CONFIG_TWL4030_WATCHDOG) += twl4030_wdt.o
+ obj-$(CONFIG_21285_WATCHDOG) += wdt285.o
+ obj-$(CONFIG_977_WATCHDOG) += wdt977.o
+-obj-$(CONFIG_GEMINI_WATCHDOG) += gemini_wdt.o
++obj-$(CONFIG_FTWDT010_WATCHDOG) += ftwdt010_wdt.o
+ obj-$(CONFIG_IXP4XX_WATCHDOG) += ixp4xx_wdt.o
+ obj-$(CONFIG_KS8695_WATCHDOG) += ks8695_wdt.o
+ obj-$(CONFIG_S3C2410_WATCHDOG) += s3c2410_wdt.o
+--- a/drivers/watchdog/gemini_wdt.c
++++ /dev/null
+@@ -1,229 +0,0 @@
+-/*
+- * Watchdog driver for Cortina Systems Gemini SoC
+- *
+- * Copyright (C) 2017 Linus Walleij <linus.walleij at linaro.org>
+- *
+- * Inspired by the out-of-tree drivers from OpenWRT:
+- * Copyright (C) 2009 Paulius Zaleckas <paulius.zaleckas at teltonika.lt>
+- *
+- * This program is free software; you can redistribute it and/or modify
+- * it under the terms of the GNU General Public License version 2 as
+- * published by the Free Software Foundation.
+- */
+-
+-#include <linux/bitops.h>
+-#include <linux/init.h>
+-#include <linux/interrupt.h>
+-#include <linux/io.h>
+-#include <linux/kernel.h>
+-#include <linux/module.h>
+-#include <linux/of_device.h>
+-#include <linux/platform_device.h>
+-#include <linux/slab.h>
+-#include <linux/watchdog.h>
+-
+-#define GEMINI_WDCOUNTER 0x0
+-#define GEMINI_WDLOAD 0x4
+-#define GEMINI_WDRESTART 0x8
+-#define GEMINI_WDCR 0xC
+-
+-#define WDRESTART_MAGIC 0x5AB9
+-
+-#define WDCR_CLOCK_5MHZ BIT(4)
+-#define WDCR_SYS_RST BIT(1)
+-#define WDCR_ENABLE BIT(0)
+-
+-#define WDT_CLOCK 5000000 /* 5 MHz */
+-
+-struct gemini_wdt {
+- struct watchdog_device wdd;
+- struct device *dev;
+- void __iomem *base;
+-};
+-
+-static inline
+-struct gemini_wdt *to_gemini_wdt(struct watchdog_device *wdd)
+-{
+- return container_of(wdd, struct gemini_wdt, wdd);
+-}
+-
+-static int gemini_wdt_start(struct watchdog_device *wdd)
+-{
+- struct gemini_wdt *gwdt = to_gemini_wdt(wdd);
+-
+- writel(wdd->timeout * WDT_CLOCK, gwdt->base + GEMINI_WDLOAD);
+- writel(WDRESTART_MAGIC, gwdt->base + GEMINI_WDRESTART);
+- /* set clock before enabling */
+- writel(WDCR_CLOCK_5MHZ | WDCR_SYS_RST,
+- gwdt->base + GEMINI_WDCR);
+- writel(WDCR_CLOCK_5MHZ | WDCR_SYS_RST | WDCR_ENABLE,
+- gwdt->base + GEMINI_WDCR);
+-
+- return 0;
+-}
+-
+-static int gemini_wdt_stop(struct watchdog_device *wdd)
+-{
+- struct gemini_wdt *gwdt = to_gemini_wdt(wdd);
+-
+- writel(0, gwdt->base + GEMINI_WDCR);
+-
+- return 0;
+-}
+-
+-static int gemini_wdt_ping(struct watchdog_device *wdd)
+-{
+- struct gemini_wdt *gwdt = to_gemini_wdt(wdd);
+-
+- writel(WDRESTART_MAGIC, gwdt->base + GEMINI_WDRESTART);
+-
+- return 0;
+-}
+-
+-static int gemini_wdt_set_timeout(struct watchdog_device *wdd,
+- unsigned int timeout)
+-{
+- wdd->timeout = timeout;
+- if (watchdog_active(wdd))
+- gemini_wdt_start(wdd);
+-
+- return 0;
+-}
+-
+-static irqreturn_t gemini_wdt_interrupt(int irq, void *data)
+-{
+- struct gemini_wdt *gwdt = data;
+-
+- watchdog_notify_pretimeout(&gwdt->wdd);
+-
+- return IRQ_HANDLED;
+-}
+-
+-static const struct watchdog_ops gemini_wdt_ops = {
+- .start = gemini_wdt_start,
+- .stop = gemini_wdt_stop,
+- .ping = gemini_wdt_ping,
+- .set_timeout = gemini_wdt_set_timeout,
+- .owner = THIS_MODULE,
+-};
+-
+-static const struct watchdog_info gemini_wdt_info = {
+- .options = WDIOF_KEEPALIVEPING
+- | WDIOF_MAGICCLOSE
+- | WDIOF_SETTIMEOUT,
+- .identity = KBUILD_MODNAME,
+-};
+-
+-
+-static int gemini_wdt_probe(struct platform_device *pdev)
+-{
+- struct device *dev = &pdev->dev;
+- struct resource *res;
+- struct gemini_wdt *gwdt;
+- unsigned int reg;
+- int irq;
+- int ret;
+-
+- gwdt = devm_kzalloc(dev, sizeof(*gwdt), GFP_KERNEL);
+- if (!gwdt)
+- return -ENOMEM;
+-
+- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+- gwdt->base = devm_ioremap_resource(dev, res);
+- if (IS_ERR(gwdt->base))
+- return PTR_ERR(gwdt->base);
+-
+- irq = platform_get_irq(pdev, 0);
+- if (!irq)
+- return -EINVAL;
+-
+- gwdt->dev = dev;
+- gwdt->wdd.info = &gemini_wdt_info;
+- gwdt->wdd.ops = &gemini_wdt_ops;
+- gwdt->wdd.min_timeout = 1;
+- gwdt->wdd.max_timeout = 0xFFFFFFFF / WDT_CLOCK;
+- gwdt->wdd.parent = dev;
+-
+- /*
+- * If 'timeout-sec' unspecified in devicetree, assume a 13 second
+- * default.
+- */
+- gwdt->wdd.timeout = 13U;
+- watchdog_init_timeout(&gwdt->wdd, 0, dev);
+-
+- reg = readw(gwdt->base + GEMINI_WDCR);
+- if (reg & WDCR_ENABLE) {
+- /* Watchdog was enabled by the bootloader, disable it. */
+- reg &= ~WDCR_ENABLE;
+- writel(reg, gwdt->base + GEMINI_WDCR);
+- }
+-
+- ret = devm_request_irq(dev, irq, gemini_wdt_interrupt, 0,
+- "watchdog bark", gwdt);
+- if (ret)
+- return ret;
+-
+- ret = devm_watchdog_register_device(dev, &gwdt->wdd);
+- if (ret) {
+- dev_err(&pdev->dev, "failed to register watchdog\n");
+- return ret;
+- }
+-
+- /* Set up platform driver data */
+- platform_set_drvdata(pdev, gwdt);
+- dev_info(dev, "Gemini watchdog driver enabled\n");
+-
+- return 0;
+-}
+-
+-static int __maybe_unused gemini_wdt_suspend(struct device *dev)
+-{
+- struct gemini_wdt *gwdt = dev_get_drvdata(dev);
+- unsigned int reg;
+-
+- reg = readw(gwdt->base + GEMINI_WDCR);
+- reg &= ~WDCR_ENABLE;
+- writel(reg, gwdt->base + GEMINI_WDCR);
+-
+- return 0;
+-}
+-
+-static int __maybe_unused gemini_wdt_resume(struct device *dev)
+-{
+- struct gemini_wdt *gwdt = dev_get_drvdata(dev);
+- unsigned int reg;
+-
+- if (watchdog_active(&gwdt->wdd)) {
+- reg = readw(gwdt->base + GEMINI_WDCR);
+- reg |= WDCR_ENABLE;
+- writel(reg, gwdt->base + GEMINI_WDCR);
+- }
+-
+- return 0;
+-}
+-
+-static const struct dev_pm_ops gemini_wdt_dev_pm_ops = {
+- SET_SYSTEM_SLEEP_PM_OPS(gemini_wdt_suspend,
+- gemini_wdt_resume)
+-};
+-
+-#ifdef CONFIG_OF
+-static const struct of_device_id gemini_wdt_match[] = {
+- { .compatible = "cortina,gemini-watchdog" },
+- {},
+-};
+-MODULE_DEVICE_TABLE(of, gemini_wdt_match);
+-#endif
+-
+-static struct platform_driver gemini_wdt_driver = {
+- .probe = gemini_wdt_probe,
+- .driver = {
+- .name = "gemini-wdt",
+- .of_match_table = of_match_ptr(gemini_wdt_match),
+- .pm = &gemini_wdt_dev_pm_ops,
+- },
+-};
+-module_platform_driver(gemini_wdt_driver);
+-MODULE_AUTHOR("Linus Walleij");
+-MODULE_DESCRIPTION("Watchdog driver for Gemini");
+-MODULE_LICENSE("GPL");
+--- /dev/null
++++ b/drivers/watchdog/ftwdt010_wdt.c
+@@ -0,0 +1,230 @@
++/*
++ * Watchdog driver for Faraday Technology FTWDT010
++ *
++ * Copyright (C) 2017 Linus Walleij <linus.walleij at linaro.org>
++ *
++ * Inspired by the out-of-tree drivers from OpenWRT:
++ * Copyright (C) 2009 Paulius Zaleckas <paulius.zaleckas at teltonika.lt>
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ */
++
++#include <linux/bitops.h>
++#include <linux/init.h>
++#include <linux/interrupt.h>
++#include <linux/io.h>
++#include <linux/kernel.h>
++#include <linux/module.h>
++#include <linux/of_device.h>
++#include <linux/platform_device.h>
++#include <linux/slab.h>
++#include <linux/watchdog.h>
++
++#define FTWDT010_WDCOUNTER 0x0
++#define FTWDT010_WDLOAD 0x4
++#define FTWDT010_WDRESTART 0x8
++#define FTWDT010_WDCR 0xC
++
++#define WDRESTART_MAGIC 0x5AB9
++
++#define WDCR_CLOCK_5MHZ BIT(4)
++#define WDCR_SYS_RST BIT(1)
++#define WDCR_ENABLE BIT(0)
++
++#define WDT_CLOCK 5000000 /* 5 MHz */
++
++struct ftwdt010_wdt {
++ struct watchdog_device wdd;
++ struct device *dev;
++ void __iomem *base;
++};
++
++static inline
++struct ftwdt010_wdt *to_ftwdt010_wdt(struct watchdog_device *wdd)
++{
++ return container_of(wdd, struct ftwdt010_wdt, wdd);
++}
++
++static int ftwdt010_wdt_start(struct watchdog_device *wdd)
++{
++ struct ftwdt010_wdt *gwdt = to_ftwdt010_wdt(wdd);
++
++ writel(wdd->timeout * WDT_CLOCK, gwdt->base + FTWDT010_WDLOAD);
++ writel(WDRESTART_MAGIC, gwdt->base + FTWDT010_WDRESTART);
++ /* set clock before enabling */
++ writel(WDCR_CLOCK_5MHZ | WDCR_SYS_RST,
++ gwdt->base + FTWDT010_WDCR);
++ writel(WDCR_CLOCK_5MHZ | WDCR_SYS_RST | WDCR_ENABLE,
++ gwdt->base + FTWDT010_WDCR);
++
++ return 0;
++}
++
++static int ftwdt010_wdt_stop(struct watchdog_device *wdd)
++{
++ struct ftwdt010_wdt *gwdt = to_ftwdt010_wdt(wdd);
++
++ writel(0, gwdt->base + FTWDT010_WDCR);
++
++ return 0;
++}
++
++static int ftwdt010_wdt_ping(struct watchdog_device *wdd)
++{
++ struct ftwdt010_wdt *gwdt = to_ftwdt010_wdt(wdd);
++
++ writel(WDRESTART_MAGIC, gwdt->base + FTWDT010_WDRESTART);
++
++ return 0;
++}
++
++static int ftwdt010_wdt_set_timeout(struct watchdog_device *wdd,
++ unsigned int timeout)
++{
++ wdd->timeout = timeout;
++ if (watchdog_active(wdd))
++ ftwdt010_wdt_start(wdd);
++
++ return 0;
++}
++
++static irqreturn_t ftwdt010_wdt_interrupt(int irq, void *data)
++{
++ struct ftwdt010_wdt *gwdt = data;
++
++ watchdog_notify_pretimeout(&gwdt->wdd);
++
++ return IRQ_HANDLED;
++}
++
++static const struct watchdog_ops ftwdt010_wdt_ops = {
++ .start = ftwdt010_wdt_start,
++ .stop = ftwdt010_wdt_stop,
++ .ping = ftwdt010_wdt_ping,
++ .set_timeout = ftwdt010_wdt_set_timeout,
++ .owner = THIS_MODULE,
++};
++
++static const struct watchdog_info ftwdt010_wdt_info = {
++ .options = WDIOF_KEEPALIVEPING
++ | WDIOF_MAGICCLOSE
++ | WDIOF_SETTIMEOUT,
++ .identity = KBUILD_MODNAME,
++};
++
++
++static int ftwdt010_wdt_probe(struct platform_device *pdev)
++{
++ struct device *dev = &pdev->dev;
++ struct resource *res;
++ struct ftwdt010_wdt *gwdt;
++ unsigned int reg;
++ int irq;
++ int ret;
++
++ gwdt = devm_kzalloc(dev, sizeof(*gwdt), GFP_KERNEL);
++ if (!gwdt)
++ return -ENOMEM;
++
++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++ gwdt->base = devm_ioremap_resource(dev, res);
++ if (IS_ERR(gwdt->base))
++ return PTR_ERR(gwdt->base);
++
++ irq = platform_get_irq(pdev, 0);
++ if (!irq)
++ return -EINVAL;
++
++ gwdt->dev = dev;
++ gwdt->wdd.info = &ftwdt010_wdt_info;
++ gwdt->wdd.ops = &ftwdt010_wdt_ops;
++ gwdt->wdd.min_timeout = 1;
++ gwdt->wdd.max_timeout = 0xFFFFFFFF / WDT_CLOCK;
++ gwdt->wdd.parent = dev;
++
++ /*
++ * If 'timeout-sec' unspecified in devicetree, assume a 13 second
++ * default.
++ */
++ gwdt->wdd.timeout = 13U;
++ watchdog_init_timeout(&gwdt->wdd, 0, dev);
++
++ reg = readw(gwdt->base + FTWDT010_WDCR);
++ if (reg & WDCR_ENABLE) {
++ /* Watchdog was enabled by the bootloader, disable it. */
++ reg &= ~WDCR_ENABLE;
++ writel(reg, gwdt->base + FTWDT010_WDCR);
++ }
++
++ ret = devm_request_irq(dev, irq, ftwdt010_wdt_interrupt, 0,
++ "watchdog bark", gwdt);
++ if (ret)
++ return ret;
++
++ ret = devm_watchdog_register_device(dev, &gwdt->wdd);
++ if (ret) {
++ dev_err(&pdev->dev, "failed to register watchdog\n");
++ return ret;
++ }
++
++ /* Set up platform driver data */
++ platform_set_drvdata(pdev, gwdt);
++ dev_info(dev, "FTWDT010 watchdog driver enabled\n");
++
++ return 0;
++}
++
++static int __maybe_unused ftwdt010_wdt_suspend(struct device *dev)
++{
++ struct ftwdt010_wdt *gwdt = dev_get_drvdata(dev);
++ unsigned int reg;
++
++ reg = readw(gwdt->base + FTWDT010_WDCR);
++ reg &= ~WDCR_ENABLE;
++ writel(reg, gwdt->base + FTWDT010_WDCR);
++
++ return 0;
++}
++
++static int __maybe_unused ftwdt010_wdt_resume(struct device *dev)
++{
++ struct ftwdt010_wdt *gwdt = dev_get_drvdata(dev);
++ unsigned int reg;
++
++ if (watchdog_active(&gwdt->wdd)) {
++ reg = readw(gwdt->base + FTWDT010_WDCR);
++ reg |= WDCR_ENABLE;
++ writel(reg, gwdt->base + FTWDT010_WDCR);
++ }
++
++ return 0;
++}
++
++static const struct dev_pm_ops ftwdt010_wdt_dev_pm_ops = {
++ SET_SYSTEM_SLEEP_PM_OPS(ftwdt010_wdt_suspend,
++ ftwdt010_wdt_resume)
++};
++
++#ifdef CONFIG_OF
++static const struct of_device_id ftwdt010_wdt_match[] = {
++ { .compatible = "faraday,ftwdt010" },
++ { .compatible = "cortina,gemini-watchdog" },
++ {},
++};
++MODULE_DEVICE_TABLE(of, ftwdt010_wdt_match);
++#endif
++
++static struct platform_driver ftwdt010_wdt_driver = {
++ .probe = ftwdt010_wdt_probe,
++ .driver = {
++ .name = "ftwdt010-wdt",
++ .of_match_table = of_match_ptr(ftwdt010_wdt_match),
++ .pm = &ftwdt010_wdt_dev_pm_ops,
++ },
++};
++module_platform_driver(ftwdt010_wdt_driver);
++MODULE_AUTHOR("Linus Walleij");
++MODULE_DESCRIPTION("Watchdog driver for Faraday Technology FTWDT010");
++MODULE_LICENSE("GPL");
diff --git a/target/linux/gemini/patches-4.14/0019-watchdog-ftwdt010-Make-interrupt-optional.patch b/target/linux/gemini/patches-4.14/0019-watchdog-ftwdt010-Make-interrupt-optional.patch
new file mode 100644
index 0000000..23c4ab5
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0019-watchdog-ftwdt010-Make-interrupt-optional.patch
@@ -0,0 +1,93 @@
+From 4347a0b0699989b889857c9d4ccfbce339859f13 Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Mon, 16 Oct 2017 22:54:25 +0200
+Subject: [PATCH 19/31] watchdog: ftwdt010: Make interrupt optional
+
+The Moxart does not appear to be using the interrupt from the
+watchdog timer, maybe it's not even routed, so as to support
+more architectures with this driver, make the interrupt
+optional.
+
+While we are at it: actually enable the use of the interrupt
+if present by setting the right bit in the control register
+and define the missing control register bits.
+
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+Reviewed-by: Guenter Roeck <linux at roeck-us.net>
+Signed-off-by: Guenter Roeck <linux at roeck-us.net>
+Signed-off-by: Wim Van Sebroeck <wim at iguana.be>
+---
+ drivers/watchdog/ftwdt010_wdt.c | 30 ++++++++++++++++++------------
+ 1 file changed, 18 insertions(+), 12 deletions(-)
+
+--- a/drivers/watchdog/ftwdt010_wdt.c
++++ b/drivers/watchdog/ftwdt010_wdt.c
+@@ -30,6 +30,8 @@
+ #define WDRESTART_MAGIC 0x5AB9
+
+ #define WDCR_CLOCK_5MHZ BIT(4)
++#define WDCR_WDEXT BIT(3)
++#define WDCR_WDINTR BIT(2)
+ #define WDCR_SYS_RST BIT(1)
+ #define WDCR_ENABLE BIT(0)
+
+@@ -39,6 +41,7 @@ struct ftwdt010_wdt {
+ struct watchdog_device wdd;
+ struct device *dev;
+ void __iomem *base;
++ bool has_irq;
+ };
+
+ static inline
+@@ -50,14 +53,17 @@ struct ftwdt010_wdt *to_ftwdt010_wdt(str
+ static int ftwdt010_wdt_start(struct watchdog_device *wdd)
+ {
+ struct ftwdt010_wdt *gwdt = to_ftwdt010_wdt(wdd);
++ u32 enable;
+
+ writel(wdd->timeout * WDT_CLOCK, gwdt->base + FTWDT010_WDLOAD);
+ writel(WDRESTART_MAGIC, gwdt->base + FTWDT010_WDRESTART);
+ /* set clock before enabling */
+- writel(WDCR_CLOCK_5MHZ | WDCR_SYS_RST,
+- gwdt->base + FTWDT010_WDCR);
+- writel(WDCR_CLOCK_5MHZ | WDCR_SYS_RST | WDCR_ENABLE,
+- gwdt->base + FTWDT010_WDCR);
++ enable = WDCR_CLOCK_5MHZ | WDCR_SYS_RST;
++ writel(enable, gwdt->base + FTWDT010_WDCR);
++ if (gwdt->has_irq)
++ enable |= WDCR_WDINTR;
++ enable |= WDCR_ENABLE;
++ writel(enable, gwdt->base + FTWDT010_WDCR);
+
+ return 0;
+ }
+@@ -133,10 +139,6 @@ static int ftwdt010_wdt_probe(struct pla
+ if (IS_ERR(gwdt->base))
+ return PTR_ERR(gwdt->base);
+
+- irq = platform_get_irq(pdev, 0);
+- if (!irq)
+- return -EINVAL;
+-
+ gwdt->dev = dev;
+ gwdt->wdd.info = &ftwdt010_wdt_info;
+ gwdt->wdd.ops = &ftwdt010_wdt_ops;
+@@ -158,10 +160,14 @@ static int ftwdt010_wdt_probe(struct pla
+ writel(reg, gwdt->base + FTWDT010_WDCR);
+ }
+
+- ret = devm_request_irq(dev, irq, ftwdt010_wdt_interrupt, 0,
+- "watchdog bark", gwdt);
+- if (ret)
+- return ret;
++ irq = platform_get_irq(pdev, 0);
++ if (irq) {
++ ret = devm_request_irq(dev, irq, ftwdt010_wdt_interrupt, 0,
++ "watchdog bark", gwdt);
++ if (ret)
++ return ret;
++ gwdt->has_irq = true;
++ }
+
+ ret = devm_watchdog_register_device(dev, &gwdt->wdd);
+ if (ret) {
diff --git a/target/linux/gemini/patches-4.14/0020-soc-Add-SoC-driver-for-Gemini.patch b/target/linux/gemini/patches-4.14/0020-soc-Add-SoC-driver-for-Gemini.patch
new file mode 100644
index 0000000..f1bbe0a
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0020-soc-Add-SoC-driver-for-Gemini.patch
@@ -0,0 +1,113 @@
+From b0a88a861b036124ef2d6acfe6dd87cfde63e750 Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Fri, 22 Dec 2017 00:19:08 +0100
+Subject: [PATCH 20/31] soc: Add SoC driver for Gemini
+
+This adds an SoC driver for the Gemini. Currently there
+is only one thing not fitting into any other framework,
+and that is the bus arbitration setting.
+
+All Gemini vendor trees seem to be setting this register to
+exactly the same arbitration so we just add a small code
+snippet to do this at subsys_init() time before any other
+drivers kick in.
+
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+Signed-off-by: Arnd Bergmann <arnd at arndb.de>
+---
+ drivers/soc/Makefile | 1 +
+ drivers/soc/gemini/Makefile | 2 ++
+ drivers/soc/gemini/soc-gemini.c | 71 +++++++++++++++++++++++++++++++++++++++++
+ 3 files changed, 74 insertions(+)
+ create mode 100644 drivers/soc/gemini/Makefile
+ create mode 100644 drivers/soc/gemini/soc-gemini.c
+
+--- a/drivers/soc/Makefile
++++ b/drivers/soc/Makefile
+@@ -9,6 +9,7 @@ obj-y += bcm/
+ obj-$(CONFIG_ARCH_DOVE) += dove/
+ obj-$(CONFIG_MACH_DOVE) += dove/
+ obj-y += fsl/
++obj-$(CONFIG_ARCH_GEMINI) += gemini/
+ obj-$(CONFIG_ARCH_MXC) += imx/
+ obj-$(CONFIG_SOC_XWAY) += lantiq/
+ obj-$(CONFIG_ARCH_MEDIATEK) += mediatek/
+--- /dev/null
++++ b/drivers/soc/gemini/Makefile
+@@ -0,0 +1,2 @@
++# SPDX-License-Identifier: GPL-2.0
++obj-y += soc-gemini.o
+--- /dev/null
++++ b/drivers/soc/gemini/soc-gemini.c
+@@ -0,0 +1,71 @@
++// SPDX-License-Identifier: GPL-2.0
++/*
++ * Copyright (C) 2017 Linaro Ltd.
++ *
++ * Author: Linus Walleij <linus.walleij at linaro.org>
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2, as
++ * published by the Free Software Foundation.
++ *
++ */
++#include <linux/init.h>
++#include <linux/kernel.h>
++#include <linux/mfd/syscon.h>
++#include <linux/regmap.h>
++#include <linux/of.h>
++
++#define GLOBAL_WORD_ID 0x00
++#define GEMINI_GLOBAL_ARB1_CTRL 0x2c
++#define GEMINI_ARB1_BURST_MASK GENMASK(21, 16)
++#define GEMINI_ARB1_BURST_SHIFT 16
++/* These all define the priority on the BUS2 backplane */
++#define GEMINI_ARB1_PRIO_MASK GENMASK(9, 0)
++#define GEMINI_ARB1_DMAC_HIGH_PRIO BIT(0)
++#define GEMINI_ARB1_IDE_HIGH_PRIO BIT(1)
++#define GEMINI_ARB1_RAID_HIGH_PRIO BIT(2)
++#define GEMINI_ARB1_SECURITY_HIGH_PRIO BIT(3)
++#define GEMINI_ARB1_GMAC0_HIGH_PRIO BIT(4)
++#define GEMINI_ARB1_GMAC1_HIGH_PRIO BIT(5)
++#define GEMINI_ARB1_USB0_HIGH_PRIO BIT(6)
++#define GEMINI_ARB1_USB1_HIGH_PRIO BIT(7)
++#define GEMINI_ARB1_PCI_HIGH_PRIO BIT(8)
++#define GEMINI_ARB1_TVE_HIGH_PRIO BIT(9)
++
++#define GEMINI_DEFAULT_BURST_SIZE 0x20
++#define GEMINI_DEFAULT_PRIO (GEMINI_ARB1_GMAC0_HIGH_PRIO | \
++ GEMINI_ARB1_GMAC1_HIGH_PRIO)
++
++static int __init gemini_soc_init(void)
++{
++ struct regmap *map;
++ u32 rev;
++ u32 val;
++ int ret;
++
++ /* Multiplatform guard, only proceed on Gemini */
++ if (!of_machine_is_compatible("cortina,gemini"))
++ return 0;
++
++ map = syscon_regmap_lookup_by_compatible("cortina,gemini-syscon");
++ if (IS_ERR(map))
++ return PTR_ERR(map);
++ ret = regmap_read(map, GLOBAL_WORD_ID, &rev);
++ if (ret)
++ return ret;
++
++ val = (GEMINI_DEFAULT_BURST_SIZE << GEMINI_ARB1_BURST_SHIFT) |
++ GEMINI_DEFAULT_PRIO;
++
++ /* Set up system arbitration */
++ regmap_update_bits(map,
++ GEMINI_GLOBAL_ARB1_CTRL,
++ GEMINI_ARB1_BURST_MASK | GEMINI_ARB1_PRIO_MASK,
++ val);
++
++ pr_info("Gemini SoC %04x revision %02x, set arbitration %08x\n",
++ rev >> 8, rev & 0xff, val);
++
++ return 0;
++}
++subsys_initcall(gemini_soc_init);
diff --git a/target/linux/gemini/patches-4.14/0021-net-ethernet-Add-DT-bindings-for-the-Gemini-ethernet.patch b/target/linux/gemini/patches-4.14/0021-net-ethernet-Add-DT-bindings-for-the-Gemini-ethernet.patch
new file mode 100644
index 0000000..19653d5
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0021-net-ethernet-Add-DT-bindings-for-the-Gemini-ethernet.patch
@@ -0,0 +1,119 @@
+From 49bc597009f52ec8970269f6201d3ed415a844ee Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Fri, 12 Jan 2018 22:34:23 +0100
+Subject: [PATCH 21/31] net: ethernet: Add DT bindings for the Gemini ethernet
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+This adds the device tree bindings for the Gemini ethernet
+controller. It is pretty straight-forward, using standard
+bindings and modelling the two child ports as child devices
+under the parent ethernet controller device.
+
+Cc: devicetree at vger.kernel.org
+Cc: Tobias Waldvogel <tobias.waldvogel at gmail.com>
+Cc: Michał Mirosław <mirq-linux at rere.qmqm.pl>
+Reviewed-by: Rob Herring <robh at kernel.org>
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+Signed-off-by: David S. Miller <davem at davemloft.net>
+---
+ .../bindings/net/cortina,gemini-ethernet.txt | 92 ++++++++++++++++++++++
+ 1 file changed, 92 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/net/cortina,gemini-ethernet.txt
+
+--- /dev/null
++++ b/Documentation/devicetree/bindings/net/cortina,gemini-ethernet.txt
+@@ -0,0 +1,92 @@
++Cortina Systems Gemini Ethernet Controller
++==========================================
++
++This ethernet controller is found in the Gemini SoC family:
++StorLink SL3512 and SL3516, also known as Cortina Systems
++CS3512 and CS3516.
++
++Required properties:
++- compatible: must be "cortina,gemini-ethernet"
++- reg: must contain the global registers and the V-bit and A-bit
++ memory areas, in total three register sets.
++- syscon: a phandle to the system controller
++- #address-cells: must be specified, must be <1>
++- #size-cells: must be specified, must be <1>
++- ranges: should be state like this giving a 1:1 address translation
++ for the subnodes
++
++The subnodes represents the two ethernet ports in this device.
++They are not independent of each other since they share resources
++in the parent node, and are thus children.
++
++Required subnodes:
++- port0: contains the resources for ethernet port 0
++- port1: contains the resources for ethernet port 1
++
++Required subnode properties:
++- compatible: must be "cortina,gemini-ethernet-port"
++- reg: must contain two register areas: the DMA/TOE memory and
++ the GMAC memory area of the port
++- interrupts: should contain the interrupt line of the port.
++ this is nominally a level interrupt active high.
++- resets: this must provide an SoC-integrated reset line for
++ the port.
++- clocks: this should contain a handle to the PCLK clock for
++ clocking the silicon in this port
++- clock-names: must be "PCLK"
++
++Optional subnode properties:
++- phy-mode: see ethernet.txt
++- phy-handle: see ethernet.txt
++
++Example:
++
++mdio-bus {
++ (...)
++ phy0: ethernet-phy at 1 {
++ reg = <1>;
++ device_type = "ethernet-phy";
++ };
++ phy1: ethernet-phy at 3 {
++ reg = <3>;
++ device_type = "ethernet-phy";
++ };
++};
++
++
++ethernet at 60000000 {
++ compatible = "cortina,gemini-ethernet";
++ reg = <0x60000000 0x4000>, /* Global registers, queue */
++ <0x60004000 0x2000>, /* V-bit */
++ <0x60006000 0x2000>; /* A-bit */
++ syscon = <&syscon>;
++ #address-cells = <1>;
++ #size-cells = <1>;
++ ranges;
++
++ gmac0: ethernet-port at 0 {
++ compatible = "cortina,gemini-ethernet-port";
++ reg = <0x60008000 0x2000>, /* Port 0 DMA/TOE */
++ <0x6000a000 0x2000>; /* Port 0 GMAC */
++ interrupt-parent = <&intcon>;
++ interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
++ resets = <&syscon GEMINI_RESET_GMAC0>;
++ clocks = <&syscon GEMINI_CLK_GATE_GMAC0>;
++ clock-names = "PCLK";
++ phy-mode = "rgmii";
++ phy-handle = <&phy0>;
++ };
++
++ gmac1: ethernet-port at 1 {
++ compatible = "cortina,gemini-ethernet-port";
++ reg = <0x6000c000 0x2000>, /* Port 1 DMA/TOE */
++ <0x6000e000 0x2000>; /* Port 1 GMAC */
++ interrupt-parent = <&intcon>;
++ interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
++ resets = <&syscon GEMINI_RESET_GMAC1>;
++ clocks = <&syscon GEMINI_CLK_GATE_GMAC1>;
++ clock-names = "PCLK";
++ phy-mode = "rgmii";
++ phy-handle = <&phy1>;
++ };
++};
diff --git a/target/linux/gemini/patches-4.14/0022-net-ethernet-Add-a-driver-for-Gemini-gigabit-etherne.patch b/target/linux/gemini/patches-4.14/0022-net-ethernet-Add-a-driver-for-Gemini-gigabit-etherne.patch
new file mode 100644
index 0000000..bad9bfa
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0022-net-ethernet-Add-a-driver-for-Gemini-gigabit-etherne.patch
@@ -0,0 +1,3661 @@
+From 07826b86d4ce4d35fd1674d7f78e4b2060ab2910 Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Fri, 12 Jan 2018 22:34:24 +0100
+Subject: [PATCH 22/31] net: ethernet: Add a driver for Gemini gigabit ethernet
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+The Gemini ethernet has been around for years as an out-of-tree
+patch used with the NAS boxen and routers built on StorLink
+SL3512 and SL3516, later Storm Semiconductor, later Cortina
+Systems. These ASICs are still being deployed and brand new
+off-the-shelf systems using it can easily be acquired.
+
+The full name of the IP block is "Net Engine and Gigabit
+Ethernet MAC" commonly just called "GMAC".
+
+The hardware block contains a common TCP Offload Enginer (TOE)
+that can be used by both MACs. The current driver does not use
+it.
+
+Cc: Tobias Waldvogel <tobias.waldvogel at gmail.com>
+Signed-off-by: Michał Mirosław <mirq-linux at rere.qmqm.pl>
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+Signed-off-by: David S. Miller <davem at davemloft.net>
+---
+ MAINTAINERS | 2 +
+ drivers/net/ethernet/Kconfig | 1 +
+ drivers/net/ethernet/Makefile | 1 +
+ drivers/net/ethernet/cortina/Kconfig | 22 +
+ drivers/net/ethernet/cortina/Makefile | 4 +
+ drivers/net/ethernet/cortina/gemini.c | 2593 +++++++++++++++++++++++++++++++++
+ drivers/net/ethernet/cortina/gemini.h | 958 ++++++++++++
+ 7 files changed, 3581 insertions(+)
+ create mode 100644 drivers/net/ethernet/cortina/Kconfig
+ create mode 100644 drivers/net/ethernet/cortina/Makefile
+ create mode 100644 drivers/net/ethernet/cortina/gemini.c
+ create mode 100644 drivers/net/ethernet/cortina/gemini.h
+
+--- a/MAINTAINERS
++++ b/MAINTAINERS
+@@ -1327,8 +1327,10 @@ T: git git://github.com/ulli-kroll/linux
+ S: Maintained
+ F: Documentation/devicetree/bindings/arm/gemini.txt
+ F: Documentation/devicetree/bindings/pinctrl/cortina,gemini-pinctrl.txt
++F: Documentation/devicetree/bindings/net/cortina,gemini-ethernet.txt
+ F: Documentation/devicetree/bindings/rtc/faraday,ftrtc010.txt
+ F: arch/arm/mach-gemini/
++F: drivers/net/ethernet/cortina/gemini/*
+ F: drivers/pinctrl/pinctrl-gemini.c
+ F: drivers/rtc/rtc-ftrtc010.c
+
+--- a/drivers/net/ethernet/Kconfig
++++ b/drivers/net/ethernet/Kconfig
+@@ -42,6 +42,7 @@ source "drivers/net/ethernet/cavium/Kcon
+ source "drivers/net/ethernet/chelsio/Kconfig"
+ source "drivers/net/ethernet/cirrus/Kconfig"
+ source "drivers/net/ethernet/cisco/Kconfig"
++source "drivers/net/ethernet/cortina/Kconfig"
+
+ config CX_ECAT
+ tristate "Beckhoff CX5020 EtherCAT master support"
+--- a/drivers/net/ethernet/Makefile
++++ b/drivers/net/ethernet/Makefile
+@@ -29,6 +29,7 @@ obj-$(CONFIG_NET_VENDOR_CAVIUM) += caviu
+ obj-$(CONFIG_NET_VENDOR_CHELSIO) += chelsio/
+ obj-$(CONFIG_NET_VENDOR_CIRRUS) += cirrus/
+ obj-$(CONFIG_NET_VENDOR_CISCO) += cisco/
++obj-$(CONFIG_NET_VENDOR_CORTINA) += cortina/
+ obj-$(CONFIG_CX_ECAT) += ec_bhf.o
+ obj-$(CONFIG_DM9000) += davicom/
+ obj-$(CONFIG_DNET) += dnet.o
+--- /dev/null
++++ b/drivers/net/ethernet/cortina/Kconfig
+@@ -0,0 +1,22 @@
++# SPDX-License-Identifier: GPL-2.0
++# Cortina ethernet devices
++
++config NET_VENDOR_CORTINA
++ bool "Cortina Gemini devices"
++ default y
++ ---help---
++ If you have a network (Ethernet) card belonging to this class, say Y
++ and read the Ethernet-HOWTO, available from
++ <http://www.tldp.org/docs.html#howto>.
++
++if NET_VENDOR_CORTINA
++
++config GEMINI_ETHERNET
++ tristate "Gemini Gigabit Ethernet support"
++ depends on OF
++ select PHYLIB
++ select CRC32
++ ---help---
++ This driver supports StorLink SL351x (Gemini) dual Gigabit Ethernet.
++
++endif # NET_VENDOR_CORTINA
+--- /dev/null
++++ b/drivers/net/ethernet/cortina/Makefile
+@@ -0,0 +1,4 @@
++# SPDX-License-Identifier: GPL-2.0
++# Makefile for the Cortina Gemini network device drivers.
++
++obj-$(CONFIG_GEMINI_ETHERNET) += gemini.o
+--- /dev/null
++++ b/drivers/net/ethernet/cortina/gemini.c
+@@ -0,0 +1,2593 @@
++// SPDX-License-Identifier: GPL-2.0
++/* Ethernet device driver for Cortina Systems Gemini SoC
++ * Also known as the StorLink SL3512 and SL3516 (SL351x) or Lepus
++ * Net Engine and Gigabit Ethernet MAC (GMAC)
++ * This hardware contains a TCP Offload Engine (TOE) but currently the
++ * driver does not make use of it.
++ *
++ * Authors:
++ * Linus Walleij <linus.walleij at linaro.org>
++ * Tobias Waldvogel <tobias.waldvogel at gmail.com> (OpenWRT)
++ * Michał Mirosław <mirq-linux at rere.qmqm.pl>
++ * Paulius Zaleckas <paulius.zaleckas at gmail.com>
++ * Giuseppe De Robertis <Giuseppe.DeRobertis at ba.infn.it>
++ * Gary Chen & Ch Hsu Storlink Semiconductor
++ */
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/module.h>
++#include <linux/platform_device.h>
++#include <linux/spinlock.h>
++#include <linux/slab.h>
++#include <linux/dma-mapping.h>
++#include <linux/cache.h>
++#include <linux/interrupt.h>
++#include <linux/reset.h>
++#include <linux/clk.h>
++#include <linux/of.h>
++#include <linux/of_mdio.h>
++#include <linux/of_net.h>
++#include <linux/of_platform.h>
++#include <linux/etherdevice.h>
++#include <linux/if_vlan.h>
++#include <linux/skbuff.h>
++#include <linux/phy.h>
++#include <linux/crc32.h>
++#include <linux/ethtool.h>
++#include <linux/tcp.h>
++#include <linux/u64_stats_sync.h>
++
++#include <linux/in.h>
++#include <linux/ip.h>
++#include <linux/ipv6.h>
++
++#include "gemini.h"
++
++#define DRV_NAME "gmac-gemini"
++#define DRV_VERSION "1.0"
++
++#define HSIZE_8 0x00
++#define HSIZE_16 0x01
++#define HSIZE_32 0x02
++
++#define HBURST_SINGLE 0x00
++#define HBURST_INCR 0x01
++#define HBURST_INCR4 0x02
++#define HBURST_INCR8 0x03
++
++#define HPROT_DATA_CACHE BIT(0)
++#define HPROT_PRIVILIGED BIT(1)
++#define HPROT_BUFFERABLE BIT(2)
++#define HPROT_CACHABLE BIT(3)
++
++#define DEFAULT_RX_COALESCE_NSECS 0
++#define DEFAULT_GMAC_RXQ_ORDER 9
++#define DEFAULT_GMAC_TXQ_ORDER 8
++#define DEFAULT_RX_BUF_ORDER 11
++#define DEFAULT_NAPI_WEIGHT 64
++#define TX_MAX_FRAGS 16
++#define TX_QUEUE_NUM 1 /* max: 6 */
++#define RX_MAX_ALLOC_ORDER 2
++
++#define GMAC0_IRQ0_2 (GMAC0_TXDERR_INT_BIT | GMAC0_TXPERR_INT_BIT | \
++ GMAC0_RXDERR_INT_BIT | GMAC0_RXPERR_INT_BIT)
++#define GMAC0_IRQ0_TXQ0_INTS (GMAC0_SWTQ00_EOF_INT_BIT | \
++ GMAC0_SWTQ00_FIN_INT_BIT)
++#define GMAC0_IRQ4_8 (GMAC0_MIB_INT_BIT | GMAC0_RX_OVERRUN_INT_BIT)
++
++#define GMAC_OFFLOAD_FEATURES (NETIF_F_SG | NETIF_F_IP_CSUM | \
++ NETIF_F_IPV6_CSUM | NETIF_F_RXCSUM | \
++ NETIF_F_TSO | NETIF_F_TSO_ECN | NETIF_F_TSO6)
++
++/**
++ * struct gmac_queue_page - page buffer per-page info
++ */
++struct gmac_queue_page {
++ struct page *page;
++ dma_addr_t mapping;
++};
++
++struct gmac_txq {
++ struct gmac_txdesc *ring;
++ struct sk_buff **skb;
++ unsigned int cptr;
++ unsigned int noirq_packets;
++};
++
++struct gemini_ethernet;
++
++struct gemini_ethernet_port {
++ u8 id; /* 0 or 1 */
++
++ struct gemini_ethernet *geth;
++ struct net_device *netdev;
++ struct device *dev;
++ void __iomem *dma_base;
++ void __iomem *gmac_base;
++ struct clk *pclk;
++ struct reset_control *reset;
++ int irq;
++ __le32 mac_addr[3];
++
++ void __iomem *rxq_rwptr;
++ struct gmac_rxdesc *rxq_ring;
++ unsigned int rxq_order;
++
++ struct napi_struct napi;
++ struct hrtimer rx_coalesce_timer;
++ unsigned int rx_coalesce_nsecs;
++ unsigned int freeq_refill;
++ struct gmac_txq txq[TX_QUEUE_NUM];
++ unsigned int txq_order;
++ unsigned int irq_every_tx_packets;
++
++ dma_addr_t rxq_dma_base;
++ dma_addr_t txq_dma_base;
++
++ unsigned int msg_enable;
++ spinlock_t config_lock; /* Locks config register */
++
++ struct u64_stats_sync tx_stats_syncp;
++ struct u64_stats_sync rx_stats_syncp;
++ struct u64_stats_sync ir_stats_syncp;
++
++ struct rtnl_link_stats64 stats;
++ u64 hw_stats[RX_STATS_NUM];
++ u64 rx_stats[RX_STATUS_NUM];
++ u64 rx_csum_stats[RX_CHKSUM_NUM];
++ u64 rx_napi_exits;
++ u64 tx_frag_stats[TX_MAX_FRAGS];
++ u64 tx_frags_linearized;
++ u64 tx_hw_csummed;
++};
++
++struct gemini_ethernet {
++ struct device *dev;
++ void __iomem *base;
++ struct gemini_ethernet_port *port0;
++ struct gemini_ethernet_port *port1;
++
++ spinlock_t irq_lock; /* Locks IRQ-related registers */
++ unsigned int freeq_order;
++ unsigned int freeq_frag_order;
++ struct gmac_rxdesc *freeq_ring;
++ dma_addr_t freeq_dma_base;
++ struct gmac_queue_page *freeq_pages;
++ unsigned int num_freeq_pages;
++ spinlock_t freeq_lock; /* Locks queue from reentrance */
++};
++
++#define GMAC_STATS_NUM ( \
++ RX_STATS_NUM + RX_STATUS_NUM + RX_CHKSUM_NUM + 1 + \
++ TX_MAX_FRAGS + 2)
++
++static const char gmac_stats_strings[GMAC_STATS_NUM][ETH_GSTRING_LEN] = {
++ "GMAC_IN_DISCARDS",
++ "GMAC_IN_ERRORS",
++ "GMAC_IN_MCAST",
++ "GMAC_IN_BCAST",
++ "GMAC_IN_MAC1",
++ "GMAC_IN_MAC2",
++ "RX_STATUS_GOOD_FRAME",
++ "RX_STATUS_TOO_LONG_GOOD_CRC",
++ "RX_STATUS_RUNT_FRAME",
++ "RX_STATUS_SFD_NOT_FOUND",
++ "RX_STATUS_CRC_ERROR",
++ "RX_STATUS_TOO_LONG_BAD_CRC",
++ "RX_STATUS_ALIGNMENT_ERROR",
++ "RX_STATUS_TOO_LONG_BAD_ALIGN",
++ "RX_STATUS_RX_ERR",
++ "RX_STATUS_DA_FILTERED",
++ "RX_STATUS_BUFFER_FULL",
++ "RX_STATUS_11",
++ "RX_STATUS_12",
++ "RX_STATUS_13",
++ "RX_STATUS_14",
++ "RX_STATUS_15",
++ "RX_CHKSUM_IP_UDP_TCP_OK",
++ "RX_CHKSUM_IP_OK_ONLY",
++ "RX_CHKSUM_NONE",
++ "RX_CHKSUM_3",
++ "RX_CHKSUM_IP_ERR_UNKNOWN",
++ "RX_CHKSUM_IP_ERR",
++ "RX_CHKSUM_TCP_UDP_ERR",
++ "RX_CHKSUM_7",
++ "RX_NAPI_EXITS",
++ "TX_FRAGS[1]",
++ "TX_FRAGS[2]",
++ "TX_FRAGS[3]",
++ "TX_FRAGS[4]",
++ "TX_FRAGS[5]",
++ "TX_FRAGS[6]",
++ "TX_FRAGS[7]",
++ "TX_FRAGS[8]",
++ "TX_FRAGS[9]",
++ "TX_FRAGS[10]",
++ "TX_FRAGS[11]",
++ "TX_FRAGS[12]",
++ "TX_FRAGS[13]",
++ "TX_FRAGS[14]",
++ "TX_FRAGS[15]",
++ "TX_FRAGS[16+]",
++ "TX_FRAGS_LINEARIZED",
++ "TX_HW_CSUMMED",
++};
++
++static void gmac_dump_dma_state(struct net_device *netdev);
++
++static void gmac_update_config0_reg(struct net_device *netdev,
++ u32 val, u32 vmask)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ unsigned long flags;
++ u32 reg;
++
++ spin_lock_irqsave(&port->config_lock, flags);
++
++ reg = readl(port->gmac_base + GMAC_CONFIG0);
++ reg = (reg & ~vmask) | val;
++ writel(reg, port->gmac_base + GMAC_CONFIG0);
++
++ spin_unlock_irqrestore(&port->config_lock, flags);
++}
++
++static void gmac_enable_tx_rx(struct net_device *netdev)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ unsigned long flags;
++ u32 reg;
++
++ spin_lock_irqsave(&port->config_lock, flags);
++
++ reg = readl(port->gmac_base + GMAC_CONFIG0);
++ reg &= ~CONFIG0_TX_RX_DISABLE;
++ writel(reg, port->gmac_base + GMAC_CONFIG0);
++
++ spin_unlock_irqrestore(&port->config_lock, flags);
++}
++
++static void gmac_disable_tx_rx(struct net_device *netdev)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ unsigned long flags;
++ u32 val;
++
++ spin_lock_irqsave(&port->config_lock, flags);
++
++ val = readl(port->gmac_base + GMAC_CONFIG0);
++ val |= CONFIG0_TX_RX_DISABLE;
++ writel(val, port->gmac_base + GMAC_CONFIG0);
++
++ spin_unlock_irqrestore(&port->config_lock, flags);
++
++ mdelay(10); /* let GMAC consume packet */
++}
++
++static void gmac_set_flow_control(struct net_device *netdev, bool tx, bool rx)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ unsigned long flags;
++ u32 val;
++
++ spin_lock_irqsave(&port->config_lock, flags);
++
++ val = readl(port->gmac_base + GMAC_CONFIG0);
++ val &= ~CONFIG0_FLOW_CTL;
++ if (tx)
++ val |= CONFIG0_FLOW_TX;
++ if (rx)
++ val |= CONFIG0_FLOW_RX;
++ writel(val, port->gmac_base + GMAC_CONFIG0);
++
++ spin_unlock_irqrestore(&port->config_lock, flags);
++}
++
++static void gmac_speed_set(struct net_device *netdev)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ struct phy_device *phydev = netdev->phydev;
++ union gmac_status status, old_status;
++ int pause_tx = 0;
++ int pause_rx = 0;
++
++ status.bits32 = readl(port->gmac_base + GMAC_STATUS);
++ old_status.bits32 = status.bits32;
++ status.bits.link = phydev->link;
++ status.bits.duplex = phydev->duplex;
++
++ switch (phydev->speed) {
++ case 1000:
++ status.bits.speed = GMAC_SPEED_1000;
++ if (phydev->interface == PHY_INTERFACE_MODE_RGMII)
++ status.bits.mii_rmii = GMAC_PHY_RGMII_1000;
++ netdev_info(netdev, "connect to RGMII @ 1Gbit\n");
++ break;
++ case 100:
++ status.bits.speed = GMAC_SPEED_100;
++ if (phydev->interface == PHY_INTERFACE_MODE_RGMII)
++ status.bits.mii_rmii = GMAC_PHY_RGMII_100_10;
++ netdev_info(netdev, "connect to RGMII @ 100 Mbit\n");
++ break;
++ case 10:
++ status.bits.speed = GMAC_SPEED_10;
++ if (phydev->interface == PHY_INTERFACE_MODE_RGMII)
++ status.bits.mii_rmii = GMAC_PHY_RGMII_100_10;
++ netdev_info(netdev, "connect to RGMII @ 10 Mbit\n");
++ break;
++ default:
++ netdev_warn(netdev, "Not supported PHY speed (%d)\n",
++ phydev->speed);
++ }
++
++ if (phydev->duplex == DUPLEX_FULL) {
++ u16 lcladv = phy_read(phydev, MII_ADVERTISE);
++ u16 rmtadv = phy_read(phydev, MII_LPA);
++ u8 cap = mii_resolve_flowctrl_fdx(lcladv, rmtadv);
++
++ if (cap & FLOW_CTRL_RX)
++ pause_rx = 1;
++ if (cap & FLOW_CTRL_TX)
++ pause_tx = 1;
++ }
++
++ gmac_set_flow_control(netdev, pause_tx, pause_rx);
++
++ if (old_status.bits32 == status.bits32)
++ return;
++
++ if (netif_msg_link(port)) {
++ phy_print_status(phydev);
++ netdev_info(netdev, "link flow control: %s\n",
++ phydev->pause
++ ? (phydev->asym_pause ? "tx" : "both")
++ : (phydev->asym_pause ? "rx" : "none")
++ );
++ }
++
++ gmac_disable_tx_rx(netdev);
++ writel(status.bits32, port->gmac_base + GMAC_STATUS);
++ gmac_enable_tx_rx(netdev);
++}
++
++static int gmac_setup_phy(struct net_device *netdev)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ union gmac_status status = { .bits32 = 0 };
++ struct device *dev = port->dev;
++ struct phy_device *phy;
++
++ phy = of_phy_get_and_connect(netdev,
++ dev->of_node,
++ gmac_speed_set);
++ if (!phy)
++ return -ENODEV;
++ netdev->phydev = phy;
++
++ netdev_info(netdev, "connected to PHY \"%s\"\n",
++ phydev_name(phy));
++ phy_attached_print(phy, "phy_id=0x%.8lx, phy_mode=%s\n",
++ (unsigned long)phy->phy_id,
++ phy_modes(phy->interface));
++
++ phy->supported &= PHY_GBIT_FEATURES;
++ phy->supported |= SUPPORTED_Asym_Pause | SUPPORTED_Pause;
++ phy->advertising = phy->supported;
++
++ /* set PHY interface type */
++ switch (phy->interface) {
++ case PHY_INTERFACE_MODE_MII:
++ netdev_info(netdev, "set GMAC0 to GMII mode, GMAC1 disabled\n");
++ status.bits.mii_rmii = GMAC_PHY_MII;
++ netdev_info(netdev, "connect to MII\n");
++ break;
++ case PHY_INTERFACE_MODE_GMII:
++ netdev_info(netdev, "set GMAC0 to GMII mode, GMAC1 disabled\n");
++ status.bits.mii_rmii = GMAC_PHY_GMII;
++ netdev_info(netdev, "connect to GMII\n");
++ break;
++ case PHY_INTERFACE_MODE_RGMII:
++ dev_info(dev, "set GMAC0 and GMAC1 to MII/RGMII mode\n");
++ status.bits.mii_rmii = GMAC_PHY_RGMII_100_10;
++ netdev_info(netdev, "connect to RGMII\n");
++ break;
++ default:
++ netdev_err(netdev, "Unsupported MII interface\n");
++ phy_disconnect(phy);
++ netdev->phydev = NULL;
++ return -EINVAL;
++ }
++ writel(status.bits32, port->gmac_base + GMAC_STATUS);
++
++ return 0;
++}
++
++static int gmac_pick_rx_max_len(int max_l3_len)
++{
++ /* index = CONFIG_MAXLEN_XXX values */
++ static const int max_len[8] = {
++ 1536, 1518, 1522, 1542,
++ 9212, 10236, 1518, 1518
++ };
++ int i, n = 5;
++
++ max_l3_len += ETH_HLEN + VLAN_HLEN;
++
++ if (max_l3_len > max_len[n])
++ return -1;
++
++ for (i = 0; i < 5; i++) {
++ if (max_len[i] >= max_l3_len && max_len[i] < max_len[n])
++ n = i;
++ }
++
++ return n;
++}
++
++static int gmac_init(struct net_device *netdev)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ union gmac_config0 config0 = { .bits = {
++ .dis_tx = 1,
++ .dis_rx = 1,
++ .ipv4_rx_chksum = 1,
++ .ipv6_rx_chksum = 1,
++ .rx_err_detect = 1,
++ .rgmm_edge = 1,
++ .port0_chk_hwq = 1,
++ .port1_chk_hwq = 1,
++ .port0_chk_toeq = 1,
++ .port1_chk_toeq = 1,
++ .port0_chk_classq = 1,
++ .port1_chk_classq = 1,
++ } };
++ union gmac_ahb_weight ahb_weight = { .bits = {
++ .rx_weight = 1,
++ .tx_weight = 1,
++ .hash_weight = 1,
++ .pre_req = 0x1f,
++ .tq_dv_threshold = 0,
++ } };
++ union gmac_tx_wcr0 hw_weigh = { .bits = {
++ .hw_tq3 = 1,
++ .hw_tq2 = 1,
++ .hw_tq1 = 1,
++ .hw_tq0 = 1,
++ } };
++ union gmac_tx_wcr1 sw_weigh = { .bits = {
++ .sw_tq5 = 1,
++ .sw_tq4 = 1,
++ .sw_tq3 = 1,
++ .sw_tq2 = 1,
++ .sw_tq1 = 1,
++ .sw_tq0 = 1,
++ } };
++ union gmac_config1 config1 = { .bits = {
++ .set_threshold = 16,
++ .rel_threshold = 24,
++ } };
++ union gmac_config2 config2 = { .bits = {
++ .set_threshold = 16,
++ .rel_threshold = 32,
++ } };
++ union gmac_config3 config3 = { .bits = {
++ .set_threshold = 0,
++ .rel_threshold = 0,
++ } };
++ union gmac_config0 tmp;
++ u32 val;
++
++ config0.bits.max_len = gmac_pick_rx_max_len(netdev->mtu);
++ tmp.bits32 = readl(port->gmac_base + GMAC_CONFIG0);
++ config0.bits.reserved = tmp.bits.reserved;
++ writel(config0.bits32, port->gmac_base + GMAC_CONFIG0);
++ writel(config1.bits32, port->gmac_base + GMAC_CONFIG1);
++ writel(config2.bits32, port->gmac_base + GMAC_CONFIG2);
++ writel(config3.bits32, port->gmac_base + GMAC_CONFIG3);
++
++ val = readl(port->dma_base + GMAC_AHB_WEIGHT_REG);
++ writel(ahb_weight.bits32, port->dma_base + GMAC_AHB_WEIGHT_REG);
++
++ writel(hw_weigh.bits32,
++ port->dma_base + GMAC_TX_WEIGHTING_CTRL_0_REG);
++ writel(sw_weigh.bits32,
++ port->dma_base + GMAC_TX_WEIGHTING_CTRL_1_REG);
++
++ port->rxq_order = DEFAULT_GMAC_RXQ_ORDER;
++ port->txq_order = DEFAULT_GMAC_TXQ_ORDER;
++ port->rx_coalesce_nsecs = DEFAULT_RX_COALESCE_NSECS;
++
++ /* Mark every quarter of the queue a packet for interrupt
++ * in order to be able to wake up the queue if it was stopped
++ */
++ port->irq_every_tx_packets = 1 << (port->txq_order - 2);
++
++ return 0;
++}
++
++static void gmac_uninit(struct net_device *netdev)
++{
++ if (netdev->phydev)
++ phy_disconnect(netdev->phydev);
++}
++
++static int gmac_setup_txqs(struct net_device *netdev)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ unsigned int n_txq = netdev->num_tx_queues;
++ struct gemini_ethernet *geth = port->geth;
++ size_t entries = 1 << port->txq_order;
++ struct gmac_txq *txq = port->txq;
++ struct gmac_txdesc *desc_ring;
++ size_t len = n_txq * entries;
++ struct sk_buff **skb_tab;
++ void __iomem *rwptr_reg;
++ unsigned int r;
++ int i;
++
++ rwptr_reg = port->dma_base + GMAC_SW_TX_QUEUE0_PTR_REG;
++
++ skb_tab = kcalloc(len, sizeof(*skb_tab), GFP_KERNEL);
++ if (!skb_tab)
++ return -ENOMEM;
++
++ desc_ring = dma_alloc_coherent(geth->dev, len * sizeof(*desc_ring),
++ &port->txq_dma_base, GFP_KERNEL);
++
++ if (!desc_ring) {
++ kfree(skb_tab);
++ return -ENOMEM;
++ }
++
++ if (port->txq_dma_base & ~DMA_Q_BASE_MASK) {
++ dev_warn(geth->dev, "TX queue base it not aligned\n");
++ return -ENOMEM;
++ }
++
++ writel(port->txq_dma_base | port->txq_order,
++ port->dma_base + GMAC_SW_TX_QUEUE_BASE_REG);
++
++ for (i = 0; i < n_txq; i++) {
++ txq->ring = desc_ring;
++ txq->skb = skb_tab;
++ txq->noirq_packets = 0;
++
++ r = readw(rwptr_reg);
++ rwptr_reg += 2;
++ writew(r, rwptr_reg);
++ rwptr_reg += 2;
++ txq->cptr = r;
++
++ txq++;
++ desc_ring += entries;
++ skb_tab += entries;
++ }
++
++ return 0;
++}
++
++static void gmac_clean_txq(struct net_device *netdev, struct gmac_txq *txq,
++ unsigned int r)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ unsigned int m = (1 << port->txq_order) - 1;
++ struct gemini_ethernet *geth = port->geth;
++ unsigned int c = txq->cptr;
++ union gmac_txdesc_0 word0;
++ union gmac_txdesc_1 word1;
++ unsigned int hwchksum = 0;
++ unsigned long bytes = 0;
++ struct gmac_txdesc *txd;
++ unsigned short nfrags;
++ unsigned int errs = 0;
++ unsigned int pkts = 0;
++ unsigned int word3;
++ dma_addr_t mapping;
++
++ if (c == r)
++ return;
++
++ while (c != r) {
++ txd = txq->ring + c;
++ word0 = txd->word0;
++ word1 = txd->word1;
++ mapping = txd->word2.buf_adr;
++ word3 = txd->word3.bits32;
++
++ dma_unmap_single(geth->dev, mapping,
++ word0.bits.buffer_size, DMA_TO_DEVICE);
++
++ if (word3 & EOF_BIT)
++ dev_kfree_skb(txq->skb[c]);
++
++ c++;
++ c &= m;
++
++ if (!(word3 & SOF_BIT))
++ continue;
++
++ if (!word0.bits.status_tx_ok) {
++ errs++;
++ continue;
++ }
++
++ pkts++;
++ bytes += txd->word1.bits.byte_count;
++
++ if (word1.bits32 & TSS_CHECKUM_ENABLE)
++ hwchksum++;
++
++ nfrags = word0.bits.desc_count - 1;
++ if (nfrags) {
++ if (nfrags >= TX_MAX_FRAGS)
++ nfrags = TX_MAX_FRAGS - 1;
++
++ u64_stats_update_begin(&port->tx_stats_syncp);
++ port->tx_frag_stats[nfrags]++;
++ u64_stats_update_end(&port->ir_stats_syncp);
++ }
++ }
++
++ u64_stats_update_begin(&port->ir_stats_syncp);
++ port->stats.tx_errors += errs;
++ port->stats.tx_packets += pkts;
++ port->stats.tx_bytes += bytes;
++ port->tx_hw_csummed += hwchksum;
++ u64_stats_update_end(&port->ir_stats_syncp);
++
++ txq->cptr = c;
++}
++
++static void gmac_cleanup_txqs(struct net_device *netdev)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ unsigned int n_txq = netdev->num_tx_queues;
++ struct gemini_ethernet *geth = port->geth;
++ void __iomem *rwptr_reg;
++ unsigned int r, i;
++
++ rwptr_reg = port->dma_base + GMAC_SW_TX_QUEUE0_PTR_REG;
++
++ for (i = 0; i < n_txq; i++) {
++ r = readw(rwptr_reg);
++ rwptr_reg += 2;
++ writew(r, rwptr_reg);
++ rwptr_reg += 2;
++
++ gmac_clean_txq(netdev, port->txq + i, r);
++ }
++ writel(0, port->dma_base + GMAC_SW_TX_QUEUE_BASE_REG);
++
++ kfree(port->txq->skb);
++ dma_free_coherent(geth->dev,
++ n_txq * sizeof(*port->txq->ring) << port->txq_order,
++ port->txq->ring, port->txq_dma_base);
++}
++
++static int gmac_setup_rxq(struct net_device *netdev)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ struct gemini_ethernet *geth = port->geth;
++ struct nontoe_qhdr __iomem *qhdr;
++
++ qhdr = geth->base + TOE_DEFAULT_Q_HDR_BASE(netdev->dev_id);
++ port->rxq_rwptr = &qhdr->word1;
++
++ /* Remap a slew of memory to use for the RX queue */
++ port->rxq_ring = dma_alloc_coherent(geth->dev,
++ sizeof(*port->rxq_ring) << port->rxq_order,
++ &port->rxq_dma_base, GFP_KERNEL);
++ if (!port->rxq_ring)
++ return -ENOMEM;
++ if (port->rxq_dma_base & ~NONTOE_QHDR0_BASE_MASK) {
++ dev_warn(geth->dev, "RX queue base it not aligned\n");
++ return -ENOMEM;
++ }
++
++ writel(port->rxq_dma_base | port->rxq_order, &qhdr->word0);
++ writel(0, port->rxq_rwptr);
++ return 0;
++}
++
++static struct gmac_queue_page *
++gmac_get_queue_page(struct gemini_ethernet *geth,
++ struct gemini_ethernet_port *port,
++ dma_addr_t addr)
++{
++ struct gmac_queue_page *gpage;
++ dma_addr_t mapping;
++ int i;
++
++ /* Only look for even pages */
++ mapping = addr & PAGE_MASK;
++
++ if (!geth->freeq_pages) {
++ dev_err(geth->dev, "try to get page with no page list\n");
++ return NULL;
++ }
++
++ /* Look up a ring buffer page from virtual mapping */
++ for (i = 0; i < geth->num_freeq_pages; i++) {
++ gpage = &geth->freeq_pages[i];
++ if (gpage->mapping == mapping)
++ return gpage;
++ }
++
++ return NULL;
++}
++
++static void gmac_cleanup_rxq(struct net_device *netdev)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ struct gemini_ethernet *geth = port->geth;
++ struct gmac_rxdesc *rxd = port->rxq_ring;
++ static struct gmac_queue_page *gpage;
++ struct nontoe_qhdr __iomem *qhdr;
++ void __iomem *dma_reg;
++ void __iomem *ptr_reg;
++ dma_addr_t mapping;
++ union dma_rwptr rw;
++ unsigned int r, w;
++
++ qhdr = geth->base +
++ TOE_DEFAULT_Q_HDR_BASE(netdev->dev_id);
++ dma_reg = &qhdr->word0;
++ ptr_reg = &qhdr->word1;
++
++ rw.bits32 = readl(ptr_reg);
++ r = rw.bits.rptr;
++ w = rw.bits.wptr;
++ writew(r, ptr_reg + 2);
++
++ writel(0, dma_reg);
++
++ /* Loop from read pointer to write pointer of the RX queue
++ * and free up all pages by the queue.
++ */
++ while (r != w) {
++ mapping = rxd[r].word2.buf_adr;
++ r++;
++ r &= ((1 << port->rxq_order) - 1);
++
++ if (!mapping)
++ continue;
++
++ /* Freeq pointers are one page off */
++ gpage = gmac_get_queue_page(geth, port, mapping + PAGE_SIZE);
++ if (!gpage) {
++ dev_err(geth->dev, "could not find page\n");
++ continue;
++ }
++ /* Release the RX queue reference to the page */
++ put_page(gpage->page);
++ }
++
++ dma_free_coherent(geth->dev, sizeof(*port->rxq_ring) << port->rxq_order,
++ port->rxq_ring, port->rxq_dma_base);
++}
++
++static struct page *geth_freeq_alloc_map_page(struct gemini_ethernet *geth,
++ int pn)
++{
++ struct gmac_rxdesc *freeq_entry;
++ struct gmac_queue_page *gpage;
++ unsigned int fpp_order;
++ unsigned int frag_len;
++ dma_addr_t mapping;
++ struct page *page;
++ int i;
++
++ /* First allocate and DMA map a single page */
++ page = alloc_page(GFP_ATOMIC);
++ if (!page)
++ return NULL;
++
++ mapping = dma_map_single(geth->dev, page_address(page),
++ PAGE_SIZE, DMA_FROM_DEVICE);
++ if (dma_mapping_error(geth->dev, mapping)) {
++ put_page(page);
++ return NULL;
++ }
++
++ /* The assign the page mapping (physical address) to the buffer address
++ * in the hardware queue. PAGE_SHIFT on ARM is 12 (1 page is 4096 bytes,
++ * 4k), and the default RX frag order is 11 (fragments are up 20 2048
++ * bytes, 2k) so fpp_order (fragments per page order) is default 1. Thus
++ * each page normally needs two entries in the queue.
++ */
++ frag_len = 1 << geth->freeq_frag_order; /* Usually 2048 */
++ fpp_order = PAGE_SHIFT - geth->freeq_frag_order;
++ freeq_entry = geth->freeq_ring + (pn << fpp_order);
++ dev_dbg(geth->dev, "allocate page %d fragment length %d fragments per page %d, freeq entry %p\n",
++ pn, frag_len, (1 << fpp_order), freeq_entry);
++ for (i = (1 << fpp_order); i > 0; i--) {
++ freeq_entry->word2.buf_adr = mapping;
++ freeq_entry++;
++ mapping += frag_len;
++ }
++
++ /* If the freeq entry already has a page mapped, then unmap it. */
++ gpage = &geth->freeq_pages[pn];
++ if (gpage->page) {
++ mapping = geth->freeq_ring[pn << fpp_order].word2.buf_adr;
++ dma_unmap_single(geth->dev, mapping, frag_len, DMA_FROM_DEVICE);
++ /* This should be the last reference to the page so it gets
++ * released
++ */
++ put_page(gpage->page);
++ }
++
++ /* Then put our new mapping into the page table */
++ dev_dbg(geth->dev, "page %d, DMA addr: %08x, page %p\n",
++ pn, (unsigned int)mapping, page);
++ gpage->mapping = mapping;
++ gpage->page = page;
++
++ return page;
++}
++
++/**
++ * geth_fill_freeq() - Fill the freeq with empty fragments to use
++ * @geth: the ethernet adapter
++ * @refill: whether to reset the queue by filling in all freeq entries or
++ * just refill it, usually the interrupt to refill the queue happens when
++ * the queue is half empty.
++ */
++static unsigned int geth_fill_freeq(struct gemini_ethernet *geth, bool refill)
++{
++ unsigned int fpp_order = PAGE_SHIFT - geth->freeq_frag_order;
++ unsigned int count = 0;
++ unsigned int pn, epn;
++ unsigned long flags;
++ union dma_rwptr rw;
++ unsigned int m_pn;
++
++ /* Mask for page */
++ m_pn = (1 << (geth->freeq_order - fpp_order)) - 1;
++
++ spin_lock_irqsave(&geth->freeq_lock, flags);
++
++ rw.bits32 = readl(geth->base + GLOBAL_SWFQ_RWPTR_REG);
++ pn = (refill ? rw.bits.wptr : rw.bits.rptr) >> fpp_order;
++ epn = (rw.bits.rptr >> fpp_order) - 1;
++ epn &= m_pn;
++
++ /* Loop over the freeq ring buffer entries */
++ while (pn != epn) {
++ struct gmac_queue_page *gpage;
++ struct page *page;
++
++ gpage = &geth->freeq_pages[pn];
++ page = gpage->page;
++
++ dev_dbg(geth->dev, "fill entry %d page ref count %d add %d refs\n",
++ pn, page_ref_count(page), 1 << fpp_order);
++
++ if (page_ref_count(page) > 1) {
++ unsigned int fl = (pn - epn) & m_pn;
++
++ if (fl > 64 >> fpp_order)
++ break;
++
++ page = geth_freeq_alloc_map_page(geth, pn);
++ if (!page)
++ break;
++ }
++
++ /* Add one reference per fragment in the page */
++ page_ref_add(page, 1 << fpp_order);
++ count += 1 << fpp_order;
++ pn++;
++ pn &= m_pn;
++ }
++
++ writew(pn << fpp_order, geth->base + GLOBAL_SWFQ_RWPTR_REG + 2);
++
++ spin_unlock_irqrestore(&geth->freeq_lock, flags);
++
++ return count;
++}
++
++static int geth_setup_freeq(struct gemini_ethernet *geth)
++{
++ unsigned int fpp_order = PAGE_SHIFT - geth->freeq_frag_order;
++ unsigned int frag_len = 1 << geth->freeq_frag_order;
++ unsigned int len = 1 << geth->freeq_order;
++ unsigned int pages = len >> fpp_order;
++ union queue_threshold qt;
++ union dma_skb_size skbsz;
++ unsigned int filled;
++ unsigned int pn;
++
++ geth->freeq_ring = dma_alloc_coherent(geth->dev,
++ sizeof(*geth->freeq_ring) << geth->freeq_order,
++ &geth->freeq_dma_base, GFP_KERNEL);
++ if (!geth->freeq_ring)
++ return -ENOMEM;
++ if (geth->freeq_dma_base & ~DMA_Q_BASE_MASK) {
++ dev_warn(geth->dev, "queue ring base it not aligned\n");
++ goto err_freeq;
++ }
++
++ /* Allocate a mapping to page look-up index */
++ geth->freeq_pages = kzalloc(pages * sizeof(*geth->freeq_pages),
++ GFP_KERNEL);
++ if (!geth->freeq_pages)
++ goto err_freeq;
++ geth->num_freeq_pages = pages;
++
++ dev_info(geth->dev, "allocate %d pages for queue\n", pages);
++ for (pn = 0; pn < pages; pn++)
++ if (!geth_freeq_alloc_map_page(geth, pn))
++ goto err_freeq_alloc;
++
++ filled = geth_fill_freeq(geth, false);
++ if (!filled)
++ goto err_freeq_alloc;
++
++ qt.bits32 = readl(geth->base + GLOBAL_QUEUE_THRESHOLD_REG);
++ qt.bits.swfq_empty = 32;
++ writel(qt.bits32, geth->base + GLOBAL_QUEUE_THRESHOLD_REG);
++
++ skbsz.bits.sw_skb_size = 1 << geth->freeq_frag_order;
++ writel(skbsz.bits32, geth->base + GLOBAL_DMA_SKB_SIZE_REG);
++ writel(geth->freeq_dma_base | geth->freeq_order,
++ geth->base + GLOBAL_SW_FREEQ_BASE_SIZE_REG);
++
++ return 0;
++
++err_freeq_alloc:
++ while (pn > 0) {
++ struct gmac_queue_page *gpage;
++ dma_addr_t mapping;
++
++ --pn;
++ mapping = geth->freeq_ring[pn << fpp_order].word2.buf_adr;
++ dma_unmap_single(geth->dev, mapping, frag_len, DMA_FROM_DEVICE);
++ gpage = &geth->freeq_pages[pn];
++ put_page(gpage->page);
++ }
++
++ kfree(geth->freeq_pages);
++err_freeq:
++ dma_free_coherent(geth->dev,
++ sizeof(*geth->freeq_ring) << geth->freeq_order,
++ geth->freeq_ring, geth->freeq_dma_base);
++ geth->freeq_ring = NULL;
++ return -ENOMEM;
++}
++
++/**
++ * geth_cleanup_freeq() - cleanup the DMA mappings and free the queue
++ * @geth: the Gemini global ethernet state
++ */
++static void geth_cleanup_freeq(struct gemini_ethernet *geth)
++{
++ unsigned int fpp_order = PAGE_SHIFT - geth->freeq_frag_order;
++ unsigned int frag_len = 1 << geth->freeq_frag_order;
++ unsigned int len = 1 << geth->freeq_order;
++ unsigned int pages = len >> fpp_order;
++ unsigned int pn;
++
++ writew(readw(geth->base + GLOBAL_SWFQ_RWPTR_REG),
++ geth->base + GLOBAL_SWFQ_RWPTR_REG + 2);
++ writel(0, geth->base + GLOBAL_SW_FREEQ_BASE_SIZE_REG);
++
++ for (pn = 0; pn < pages; pn++) {
++ struct gmac_queue_page *gpage;
++ dma_addr_t mapping;
++
++ mapping = geth->freeq_ring[pn << fpp_order].word2.buf_adr;
++ dma_unmap_single(geth->dev, mapping, frag_len, DMA_FROM_DEVICE);
++
++ gpage = &geth->freeq_pages[pn];
++ while (page_ref_count(gpage->page) > 0)
++ put_page(gpage->page);
++ }
++
++ kfree(geth->freeq_pages);
++
++ dma_free_coherent(geth->dev,
++ sizeof(*geth->freeq_ring) << geth->freeq_order,
++ geth->freeq_ring, geth->freeq_dma_base);
++}
++
++/**
++ * geth_resize_freeq() - resize the software queue depth
++ * @port: the port requesting the change
++ *
++ * This gets called at least once during probe() so the device queue gets
++ * "resized" from the hardware defaults. Since both ports/net devices share
++ * the same hardware queue, some synchronization between the ports is
++ * needed.
++ */
++static int geth_resize_freeq(struct gemini_ethernet_port *port)
++{
++ struct gemini_ethernet *geth = port->geth;
++ struct net_device *netdev = port->netdev;
++ struct gemini_ethernet_port *other_port;
++ struct net_device *other_netdev;
++ unsigned int new_size = 0;
++ unsigned int new_order;
++ unsigned long flags;
++ u32 en;
++ int ret;
++
++ if (netdev->dev_id == 0)
++ other_netdev = geth->port1->netdev;
++ else
++ other_netdev = geth->port0->netdev;
++
++ if (other_netdev && netif_running(other_netdev))
++ return -EBUSY;
++
++ new_size = 1 << (port->rxq_order + 1);
++ netdev_dbg(netdev, "port %d size: %d order %d\n",
++ netdev->dev_id,
++ new_size,
++ port->rxq_order);
++ if (other_netdev) {
++ other_port = netdev_priv(other_netdev);
++ new_size += 1 << (other_port->rxq_order + 1);
++ netdev_dbg(other_netdev, "port %d size: %d order %d\n",
++ other_netdev->dev_id,
++ (1 << (other_port->rxq_order + 1)),
++ other_port->rxq_order);
++ }
++
++ new_order = min(15, ilog2(new_size - 1) + 1);
++ dev_dbg(geth->dev, "set shared queue to size %d order %d\n",
++ new_size, new_order);
++ if (geth->freeq_order == new_order)
++ return 0;
++
++ spin_lock_irqsave(&geth->irq_lock, flags);
++
++ /* Disable the software queue IRQs */
++ en = readl(geth->base + GLOBAL_INTERRUPT_ENABLE_4_REG);
++ en &= ~SWFQ_EMPTY_INT_BIT;
++ writel(en, geth->base + GLOBAL_INTERRUPT_ENABLE_4_REG);
++ spin_unlock_irqrestore(&geth->irq_lock, flags);
++
++ /* Drop the old queue */
++ if (geth->freeq_ring)
++ geth_cleanup_freeq(geth);
++
++ /* Allocate a new queue with the desired order */
++ geth->freeq_order = new_order;
++ ret = geth_setup_freeq(geth);
++
++ /* Restart the interrupts - NOTE if this is the first resize
++ * after probe(), this is where the interrupts get turned on
++ * in the first place.
++ */
++ spin_lock_irqsave(&geth->irq_lock, flags);
++ en |= SWFQ_EMPTY_INT_BIT;
++ writel(en, geth->base + GLOBAL_INTERRUPT_ENABLE_4_REG);
++ spin_unlock_irqrestore(&geth->irq_lock, flags);
++
++ return ret;
++}
++
++static void gmac_tx_irq_enable(struct net_device *netdev,
++ unsigned int txq, int en)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ struct gemini_ethernet *geth = port->geth;
++ u32 val, mask;
++
++ netdev_dbg(netdev, "%s device %d\n", __func__, netdev->dev_id);
++
++ mask = GMAC0_IRQ0_TXQ0_INTS << (6 * netdev->dev_id + txq);
++
++ if (en)
++ writel(mask, geth->base + GLOBAL_INTERRUPT_STATUS_0_REG);
++
++ val = readl(geth->base + GLOBAL_INTERRUPT_ENABLE_0_REG);
++ val = en ? val | mask : val & ~mask;
++ writel(val, geth->base + GLOBAL_INTERRUPT_ENABLE_0_REG);
++}
++
++static void gmac_tx_irq(struct net_device *netdev, unsigned int txq_num)
++{
++ struct netdev_queue *ntxq = netdev_get_tx_queue(netdev, txq_num);
++
++ gmac_tx_irq_enable(netdev, txq_num, 0);
++ netif_tx_wake_queue(ntxq);
++}
++
++static int gmac_map_tx_bufs(struct net_device *netdev, struct sk_buff *skb,
++ struct gmac_txq *txq, unsigned short *desc)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ struct skb_shared_info *skb_si = skb_shinfo(skb);
++ unsigned short m = (1 << port->txq_order) - 1;
++ short frag, last_frag = skb_si->nr_frags - 1;
++ struct gemini_ethernet *geth = port->geth;
++ unsigned int word1, word3, buflen;
++ unsigned short w = *desc;
++ struct gmac_txdesc *txd;
++ skb_frag_t *skb_frag;
++ dma_addr_t mapping;
++ unsigned short mtu;
++ void *buffer;
++
++ mtu = ETH_HLEN;
++ mtu += netdev->mtu;
++ if (skb->protocol == htons(ETH_P_8021Q))
++ mtu += VLAN_HLEN;
++
++ word1 = skb->len;
++ word3 = SOF_BIT;
++
++ if (word1 > mtu) {
++ word1 |= TSS_MTU_ENABLE_BIT;
++ word3 |= mtu;
++ }
++
++ if (skb->ip_summed != CHECKSUM_NONE) {
++ int tcp = 0;
++
++ if (skb->protocol == htons(ETH_P_IP)) {
++ word1 |= TSS_IP_CHKSUM_BIT;
++ tcp = ip_hdr(skb)->protocol == IPPROTO_TCP;
++ } else { /* IPv6 */
++ word1 |= TSS_IPV6_ENABLE_BIT;
++ tcp = ipv6_hdr(skb)->nexthdr == IPPROTO_TCP;
++ }
++
++ word1 |= tcp ? TSS_TCP_CHKSUM_BIT : TSS_UDP_CHKSUM_BIT;
++ }
++
++ frag = -1;
++ while (frag <= last_frag) {
++ if (frag == -1) {
++ buffer = skb->data;
++ buflen = skb_headlen(skb);
++ } else {
++ skb_frag = skb_si->frags + frag;
++ buffer = page_address(skb_frag_page(skb_frag)) +
++ skb_frag->page_offset;
++ buflen = skb_frag->size;
++ }
++
++ if (frag == last_frag) {
++ word3 |= EOF_BIT;
++ txq->skb[w] = skb;
++ }
++
++ mapping = dma_map_single(geth->dev, buffer, buflen,
++ DMA_TO_DEVICE);
++ if (dma_mapping_error(geth->dev, mapping))
++ goto map_error;
++
++ txd = txq->ring + w;
++ txd->word0.bits32 = buflen;
++ txd->word1.bits32 = word1;
++ txd->word2.buf_adr = mapping;
++ txd->word3.bits32 = word3;
++
++ word3 &= MTU_SIZE_BIT_MASK;
++ w++;
++ w &= m;
++ frag++;
++ }
++
++ *desc = w;
++ return 0;
++
++map_error:
++ while (w != *desc) {
++ w--;
++ w &= m;
++
++ dma_unmap_page(geth->dev, txq->ring[w].word2.buf_adr,
++ txq->ring[w].word0.bits.buffer_size,
++ DMA_TO_DEVICE);
++ }
++ return -ENOMEM;
++}
++
++static int gmac_start_xmit(struct sk_buff *skb, struct net_device *netdev)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ unsigned short m = (1 << port->txq_order) - 1;
++ struct netdev_queue *ntxq;
++ unsigned short r, w, d;
++ void __iomem *ptr_reg;
++ struct gmac_txq *txq;
++ int txq_num, nfrags;
++ union dma_rwptr rw;
++
++ SKB_FRAG_ASSERT(skb);
++
++ if (skb->len >= 0x10000)
++ goto out_drop_free;
++
++ txq_num = skb_get_queue_mapping(skb);
++ ptr_reg = port->dma_base + GMAC_SW_TX_QUEUE_PTR_REG(txq_num);
++ txq = &port->txq[txq_num];
++ ntxq = netdev_get_tx_queue(netdev, txq_num);
++ nfrags = skb_shinfo(skb)->nr_frags;
++
++ rw.bits32 = readl(ptr_reg);
++ r = rw.bits.rptr;
++ w = rw.bits.wptr;
++
++ d = txq->cptr - w - 1;
++ d &= m;
++
++ if (d < nfrags + 2) {
++ gmac_clean_txq(netdev, txq, r);
++ d = txq->cptr - w - 1;
++ d &= m;
++
++ if (d < nfrags + 2) {
++ netif_tx_stop_queue(ntxq);
++
++ d = txq->cptr + nfrags + 16;
++ d &= m;
++ txq->ring[d].word3.bits.eofie = 1;
++ gmac_tx_irq_enable(netdev, txq_num, 1);
++
++ u64_stats_update_begin(&port->tx_stats_syncp);
++ netdev->stats.tx_fifo_errors++;
++ u64_stats_update_end(&port->tx_stats_syncp);
++ return NETDEV_TX_BUSY;
++ }
++ }
++
++ if (gmac_map_tx_bufs(netdev, skb, txq, &w)) {
++ if (skb_linearize(skb))
++ goto out_drop;
++
++ u64_stats_update_begin(&port->tx_stats_syncp);
++ port->tx_frags_linearized++;
++ u64_stats_update_end(&port->tx_stats_syncp);
++
++ if (gmac_map_tx_bufs(netdev, skb, txq, &w))
++ goto out_drop_free;
++ }
++
++ writew(w, ptr_reg + 2);
++
++ gmac_clean_txq(netdev, txq, r);
++ return NETDEV_TX_OK;
++
++out_drop_free:
++ dev_kfree_skb(skb);
++out_drop:
++ u64_stats_update_begin(&port->tx_stats_syncp);
++ port->stats.tx_dropped++;
++ u64_stats_update_end(&port->tx_stats_syncp);
++ return NETDEV_TX_OK;
++}
++
++static void gmac_tx_timeout(struct net_device *netdev)
++{
++ netdev_err(netdev, "Tx timeout\n");
++ gmac_dump_dma_state(netdev);
++}
++
++static void gmac_enable_irq(struct net_device *netdev, int enable)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ struct gemini_ethernet *geth = port->geth;
++ unsigned long flags;
++ u32 val, mask;
++
++ netdev_info(netdev, "%s device %d %s\n", __func__,
++ netdev->dev_id, enable ? "enable" : "disable");
++ spin_lock_irqsave(&geth->irq_lock, flags);
++
++ mask = GMAC0_IRQ0_2 << (netdev->dev_id * 2);
++ val = readl(geth->base + GLOBAL_INTERRUPT_ENABLE_0_REG);
++ val = enable ? (val | mask) : (val & ~mask);
++ writel(val, geth->base + GLOBAL_INTERRUPT_ENABLE_0_REG);
++
++ mask = DEFAULT_Q0_INT_BIT << netdev->dev_id;
++ val = readl(geth->base + GLOBAL_INTERRUPT_ENABLE_1_REG);
++ val = enable ? (val | mask) : (val & ~mask);
++ writel(val, geth->base + GLOBAL_INTERRUPT_ENABLE_1_REG);
++
++ mask = GMAC0_IRQ4_8 << (netdev->dev_id * 8);
++ val = readl(geth->base + GLOBAL_INTERRUPT_ENABLE_4_REG);
++ val = enable ? (val | mask) : (val & ~mask);
++ writel(val, geth->base + GLOBAL_INTERRUPT_ENABLE_4_REG);
++
++ spin_unlock_irqrestore(&geth->irq_lock, flags);
++}
++
++static void gmac_enable_rx_irq(struct net_device *netdev, int enable)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ struct gemini_ethernet *geth = port->geth;
++ unsigned long flags;
++ u32 val, mask;
++
++ netdev_dbg(netdev, "%s device %d %s\n", __func__, netdev->dev_id,
++ enable ? "enable" : "disable");
++ spin_lock_irqsave(&geth->irq_lock, flags);
++ mask = DEFAULT_Q0_INT_BIT << netdev->dev_id;
++
++ val = readl(geth->base + GLOBAL_INTERRUPT_ENABLE_1_REG);
++ val = enable ? (val | mask) : (val & ~mask);
++ writel(val, geth->base + GLOBAL_INTERRUPT_ENABLE_1_REG);
++
++ spin_unlock_irqrestore(&geth->irq_lock, flags);
++}
++
++static struct sk_buff *gmac_skb_if_good_frame(struct gemini_ethernet_port *port,
++ union gmac_rxdesc_0 word0,
++ unsigned int frame_len)
++{
++ unsigned int rx_csum = word0.bits.chksum_status;
++ unsigned int rx_status = word0.bits.status;
++ struct sk_buff *skb = NULL;
++
++ port->rx_stats[rx_status]++;
++ port->rx_csum_stats[rx_csum]++;
++
++ if (word0.bits.derr || word0.bits.perr ||
++ rx_status || frame_len < ETH_ZLEN ||
++ rx_csum >= RX_CHKSUM_IP_ERR_UNKNOWN) {
++ port->stats.rx_errors++;
++
++ if (frame_len < ETH_ZLEN || RX_ERROR_LENGTH(rx_status))
++ port->stats.rx_length_errors++;
++ if (RX_ERROR_OVER(rx_status))
++ port->stats.rx_over_errors++;
++ if (RX_ERROR_CRC(rx_status))
++ port->stats.rx_crc_errors++;
++ if (RX_ERROR_FRAME(rx_status))
++ port->stats.rx_frame_errors++;
++ return NULL;
++ }
++
++ skb = napi_get_frags(&port->napi);
++ if (!skb)
++ goto update_exit;
++
++ if (rx_csum == RX_CHKSUM_IP_UDP_TCP_OK)
++ skb->ip_summed = CHECKSUM_UNNECESSARY;
++
++update_exit:
++ port->stats.rx_bytes += frame_len;
++ port->stats.rx_packets++;
++ return skb;
++}
++
++static unsigned int gmac_rx(struct net_device *netdev, unsigned int budget)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ unsigned short m = (1 << port->rxq_order) - 1;
++ struct gemini_ethernet *geth = port->geth;
++ void __iomem *ptr_reg = port->rxq_rwptr;
++ unsigned int frame_len, frag_len;
++ struct gmac_rxdesc *rx = NULL;
++ struct gmac_queue_page *gpage;
++ static struct sk_buff *skb;
++ union gmac_rxdesc_0 word0;
++ union gmac_rxdesc_1 word1;
++ union gmac_rxdesc_3 word3;
++ struct page *page = NULL;
++ unsigned int page_offs;
++ unsigned short r, w;
++ union dma_rwptr rw;
++ dma_addr_t mapping;
++ int frag_nr = 0;
++
++ rw.bits32 = readl(ptr_reg);
++ /* Reset interrupt as all packages until here are taken into account */
++ writel(DEFAULT_Q0_INT_BIT << netdev->dev_id,
++ geth->base + GLOBAL_INTERRUPT_STATUS_1_REG);
++ r = rw.bits.rptr;
++ w = rw.bits.wptr;
++
++ while (budget && w != r) {
++ rx = port->rxq_ring + r;
++ word0 = rx->word0;
++ word1 = rx->word1;
++ mapping = rx->word2.buf_adr;
++ word3 = rx->word3;
++
++ r++;
++ r &= m;
++
++ frag_len = word0.bits.buffer_size;
++ frame_len = word1.bits.byte_count;
++ page_offs = mapping & ~PAGE_MASK;
++
++ if (!mapping) {
++ netdev_err(netdev,
++ "rxq[%u]: HW BUG: zero DMA desc\n", r);
++ goto err_drop;
++ }
++
++ /* Freeq pointers are one page off */
++ gpage = gmac_get_queue_page(geth, port, mapping + PAGE_SIZE);
++ if (!gpage) {
++ dev_err(geth->dev, "could not find mapping\n");
++ continue;
++ }
++ page = gpage->page;
++
++ if (word3.bits32 & SOF_BIT) {
++ if (skb) {
++ napi_free_frags(&port->napi);
++ port->stats.rx_dropped++;
++ }
++
++ skb = gmac_skb_if_good_frame(port, word0, frame_len);
++ if (!skb)
++ goto err_drop;
++
++ page_offs += NET_IP_ALIGN;
++ frag_len -= NET_IP_ALIGN;
++ frag_nr = 0;
++
++ } else if (!skb) {
++ put_page(page);
++ continue;
++ }
++
++ if (word3.bits32 & EOF_BIT)
++ frag_len = frame_len - skb->len;
++
++ /* append page frag to skb */
++ if (frag_nr == MAX_SKB_FRAGS)
++ goto err_drop;
++
++ if (frag_len == 0)
++ netdev_err(netdev, "Received fragment with len = 0\n");
++
++ skb_fill_page_desc(skb, frag_nr, page, page_offs, frag_len);
++ skb->len += frag_len;
++ skb->data_len += frag_len;
++ skb->truesize += frag_len;
++ frag_nr++;
++
++ if (word3.bits32 & EOF_BIT) {
++ napi_gro_frags(&port->napi);
++ skb = NULL;
++ --budget;
++ }
++ continue;
++
++err_drop:
++ if (skb) {
++ napi_free_frags(&port->napi);
++ skb = NULL;
++ }
++
++ if (mapping)
++ put_page(page);
++
++ port->stats.rx_dropped++;
++ }
++
++ writew(r, ptr_reg);
++ return budget;
++}
++
++static int gmac_napi_poll(struct napi_struct *napi, int budget)
++{
++ struct gemini_ethernet_port *port = netdev_priv(napi->dev);
++ struct gemini_ethernet *geth = port->geth;
++ unsigned int freeq_threshold;
++ unsigned int received;
++
++ freeq_threshold = 1 << (geth->freeq_order - 1);
++ u64_stats_update_begin(&port->rx_stats_syncp);
++
++ received = gmac_rx(napi->dev, budget);
++ if (received < budget) {
++ napi_gro_flush(napi, false);
++ napi_complete_done(napi, received);
++ gmac_enable_rx_irq(napi->dev, 1);
++ ++port->rx_napi_exits;
++ }
++
++ port->freeq_refill += (budget - received);
++ if (port->freeq_refill > freeq_threshold) {
++ port->freeq_refill -= freeq_threshold;
++ geth_fill_freeq(geth, true);
++ }
++
++ u64_stats_update_end(&port->rx_stats_syncp);
++ return received;
++}
++
++static void gmac_dump_dma_state(struct net_device *netdev)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ struct gemini_ethernet *geth = port->geth;
++ void __iomem *ptr_reg;
++ u32 reg[5];
++
++ /* Interrupt status */
++ reg[0] = readl(geth->base + GLOBAL_INTERRUPT_STATUS_0_REG);
++ reg[1] = readl(geth->base + GLOBAL_INTERRUPT_STATUS_1_REG);
++ reg[2] = readl(geth->base + GLOBAL_INTERRUPT_STATUS_2_REG);
++ reg[3] = readl(geth->base + GLOBAL_INTERRUPT_STATUS_3_REG);
++ reg[4] = readl(geth->base + GLOBAL_INTERRUPT_STATUS_4_REG);
++ netdev_err(netdev, "IRQ status: 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x\n",
++ reg[0], reg[1], reg[2], reg[3], reg[4]);
++
++ /* Interrupt enable */
++ reg[0] = readl(geth->base + GLOBAL_INTERRUPT_ENABLE_0_REG);
++ reg[1] = readl(geth->base + GLOBAL_INTERRUPT_ENABLE_1_REG);
++ reg[2] = readl(geth->base + GLOBAL_INTERRUPT_ENABLE_2_REG);
++ reg[3] = readl(geth->base + GLOBAL_INTERRUPT_ENABLE_3_REG);
++ reg[4] = readl(geth->base + GLOBAL_INTERRUPT_ENABLE_4_REG);
++ netdev_err(netdev, "IRQ enable: 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x\n",
++ reg[0], reg[1], reg[2], reg[3], reg[4]);
++
++ /* RX DMA status */
++ reg[0] = readl(port->dma_base + GMAC_DMA_RX_FIRST_DESC_REG);
++ reg[1] = readl(port->dma_base + GMAC_DMA_RX_CURR_DESC_REG);
++ reg[2] = GET_RPTR(port->rxq_rwptr);
++ reg[3] = GET_WPTR(port->rxq_rwptr);
++ netdev_err(netdev, "RX DMA regs: 0x%08x 0x%08x, ptr: %u %u\n",
++ reg[0], reg[1], reg[2], reg[3]);
++
++ reg[0] = readl(port->dma_base + GMAC_DMA_RX_DESC_WORD0_REG);
++ reg[1] = readl(port->dma_base + GMAC_DMA_RX_DESC_WORD1_REG);
++ reg[2] = readl(port->dma_base + GMAC_DMA_RX_DESC_WORD2_REG);
++ reg[3] = readl(port->dma_base + GMAC_DMA_RX_DESC_WORD3_REG);
++ netdev_err(netdev, "RX DMA descriptor: 0x%08x 0x%08x 0x%08x 0x%08x\n",
++ reg[0], reg[1], reg[2], reg[3]);
++
++ /* TX DMA status */
++ ptr_reg = port->dma_base + GMAC_SW_TX_QUEUE0_PTR_REG;
++
++ reg[0] = readl(port->dma_base + GMAC_DMA_TX_FIRST_DESC_REG);
++ reg[1] = readl(port->dma_base + GMAC_DMA_TX_CURR_DESC_REG);
++ reg[2] = GET_RPTR(ptr_reg);
++ reg[3] = GET_WPTR(ptr_reg);
++ netdev_err(netdev, "TX DMA regs: 0x%08x 0x%08x, ptr: %u %u\n",
++ reg[0], reg[1], reg[2], reg[3]);
++
++ reg[0] = readl(port->dma_base + GMAC_DMA_TX_DESC_WORD0_REG);
++ reg[1] = readl(port->dma_base + GMAC_DMA_TX_DESC_WORD1_REG);
++ reg[2] = readl(port->dma_base + GMAC_DMA_TX_DESC_WORD2_REG);
++ reg[3] = readl(port->dma_base + GMAC_DMA_TX_DESC_WORD3_REG);
++ netdev_err(netdev, "TX DMA descriptor: 0x%08x 0x%08x 0x%08x 0x%08x\n",
++ reg[0], reg[1], reg[2], reg[3]);
++
++ /* FREE queues status */
++ ptr_reg = geth->base + GLOBAL_SWFQ_RWPTR_REG;
++
++ reg[0] = GET_RPTR(ptr_reg);
++ reg[1] = GET_WPTR(ptr_reg);
++
++ ptr_reg = geth->base + GLOBAL_HWFQ_RWPTR_REG;
++
++ reg[2] = GET_RPTR(ptr_reg);
++ reg[3] = GET_WPTR(ptr_reg);
++ netdev_err(netdev, "FQ SW ptr: %u %u, HW ptr: %u %u\n",
++ reg[0], reg[1], reg[2], reg[3]);
++}
++
++static void gmac_update_hw_stats(struct net_device *netdev)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ unsigned int rx_discards, rx_mcast, rx_bcast;
++ struct gemini_ethernet *geth = port->geth;
++ unsigned long flags;
++
++ spin_lock_irqsave(&geth->irq_lock, flags);
++ u64_stats_update_begin(&port->ir_stats_syncp);
++
++ rx_discards = readl(port->gmac_base + GMAC_IN_DISCARDS);
++ port->hw_stats[0] += rx_discards;
++ port->hw_stats[1] += readl(port->gmac_base + GMAC_IN_ERRORS);
++ rx_mcast = readl(port->gmac_base + GMAC_IN_MCAST);
++ port->hw_stats[2] += rx_mcast;
++ rx_bcast = readl(port->gmac_base + GMAC_IN_BCAST);
++ port->hw_stats[3] += rx_bcast;
++ port->hw_stats[4] += readl(port->gmac_base + GMAC_IN_MAC1);
++ port->hw_stats[5] += readl(port->gmac_base + GMAC_IN_MAC2);
++
++ port->stats.rx_missed_errors += rx_discards;
++ port->stats.multicast += rx_mcast;
++ port->stats.multicast += rx_bcast;
++
++ writel(GMAC0_MIB_INT_BIT << (netdev->dev_id * 8),
++ geth->base + GLOBAL_INTERRUPT_STATUS_4_REG);
++
++ u64_stats_update_end(&port->ir_stats_syncp);
++ spin_unlock_irqrestore(&geth->irq_lock, flags);
++}
++
++/**
++ * gmac_get_intr_flags() - get interrupt status flags for a port from
++ * @netdev: the net device for the port to get flags from
++ * @i: the interrupt status register 0..4
++ */
++static u32 gmac_get_intr_flags(struct net_device *netdev, int i)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ struct gemini_ethernet *geth = port->geth;
++ void __iomem *irqif_reg, *irqen_reg;
++ unsigned int offs, val;
++
++ /* Calculate the offset using the stride of the status registers */
++ offs = i * (GLOBAL_INTERRUPT_STATUS_1_REG -
++ GLOBAL_INTERRUPT_STATUS_0_REG);
++
++ irqif_reg = geth->base + GLOBAL_INTERRUPT_STATUS_0_REG + offs;
++ irqen_reg = geth->base + GLOBAL_INTERRUPT_ENABLE_0_REG + offs;
++
++ val = readl(irqif_reg) & readl(irqen_reg);
++ return val;
++}
++
++static enum hrtimer_restart gmac_coalesce_delay_expired(struct hrtimer *timer)
++{
++ struct gemini_ethernet_port *port =
++ container_of(timer, struct gemini_ethernet_port,
++ rx_coalesce_timer);
++
++ napi_schedule(&port->napi);
++ return HRTIMER_NORESTART;
++}
++
++static irqreturn_t gmac_irq(int irq, void *data)
++{
++ struct gemini_ethernet_port *port;
++ struct net_device *netdev = data;
++ struct gemini_ethernet *geth;
++ u32 val, orr = 0;
++
++ port = netdev_priv(netdev);
++ geth = port->geth;
++
++ val = gmac_get_intr_flags(netdev, 0);
++ orr |= val;
++
++ if (val & (GMAC0_IRQ0_2 << (netdev->dev_id * 2))) {
++ /* Oh, crap */
++ netdev_err(netdev, "hw failure/sw bug\n");
++ gmac_dump_dma_state(netdev);
++
++ /* don't know how to recover, just reduce losses */
++ gmac_enable_irq(netdev, 0);
++ return IRQ_HANDLED;
++ }
++
++ if (val & (GMAC0_IRQ0_TXQ0_INTS << (netdev->dev_id * 6)))
++ gmac_tx_irq(netdev, 0);
++
++ val = gmac_get_intr_flags(netdev, 1);
++ orr |= val;
++
++ if (val & (DEFAULT_Q0_INT_BIT << netdev->dev_id)) {
++ gmac_enable_rx_irq(netdev, 0);
++
++ if (!port->rx_coalesce_nsecs) {
++ napi_schedule(&port->napi);
++ } else {
++ ktime_t ktime;
++
++ ktime = ktime_set(0, port->rx_coalesce_nsecs);
++ hrtimer_start(&port->rx_coalesce_timer, ktime,
++ HRTIMER_MODE_REL);
++ }
++ }
++
++ val = gmac_get_intr_flags(netdev, 4);
++ orr |= val;
++
++ if (val & (GMAC0_MIB_INT_BIT << (netdev->dev_id * 8)))
++ gmac_update_hw_stats(netdev);
++
++ if (val & (GMAC0_RX_OVERRUN_INT_BIT << (netdev->dev_id * 8))) {
++ writel(GMAC0_RXDERR_INT_BIT << (netdev->dev_id * 8),
++ geth->base + GLOBAL_INTERRUPT_STATUS_4_REG);
++
++ spin_lock(&geth->irq_lock);
++ u64_stats_update_begin(&port->ir_stats_syncp);
++ ++port->stats.rx_fifo_errors;
++ u64_stats_update_end(&port->ir_stats_syncp);
++ spin_unlock(&geth->irq_lock);
++ }
++
++ return orr ? IRQ_HANDLED : IRQ_NONE;
++}
++
++static void gmac_start_dma(struct gemini_ethernet_port *port)
++{
++ void __iomem *dma_ctrl_reg = port->dma_base + GMAC_DMA_CTRL_REG;
++ union gmac_dma_ctrl dma_ctrl;
++
++ dma_ctrl.bits32 = readl(dma_ctrl_reg);
++ dma_ctrl.bits.rd_enable = 1;
++ dma_ctrl.bits.td_enable = 1;
++ dma_ctrl.bits.loopback = 0;
++ dma_ctrl.bits.drop_small_ack = 0;
++ dma_ctrl.bits.rd_insert_bytes = NET_IP_ALIGN;
++ dma_ctrl.bits.rd_prot = HPROT_DATA_CACHE | HPROT_PRIVILIGED;
++ dma_ctrl.bits.rd_burst_size = HBURST_INCR8;
++ dma_ctrl.bits.rd_bus = HSIZE_8;
++ dma_ctrl.bits.td_prot = HPROT_DATA_CACHE;
++ dma_ctrl.bits.td_burst_size = HBURST_INCR8;
++ dma_ctrl.bits.td_bus = HSIZE_8;
++
++ writel(dma_ctrl.bits32, dma_ctrl_reg);
++}
++
++static void gmac_stop_dma(struct gemini_ethernet_port *port)
++{
++ void __iomem *dma_ctrl_reg = port->dma_base + GMAC_DMA_CTRL_REG;
++ union gmac_dma_ctrl dma_ctrl;
++
++ dma_ctrl.bits32 = readl(dma_ctrl_reg);
++ dma_ctrl.bits.rd_enable = 0;
++ dma_ctrl.bits.td_enable = 0;
++ writel(dma_ctrl.bits32, dma_ctrl_reg);
++}
++
++static int gmac_open(struct net_device *netdev)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ int err;
++
++ if (!netdev->phydev) {
++ err = gmac_setup_phy(netdev);
++ if (err) {
++ netif_err(port, ifup, netdev,
++ "PHY init failed: %d\n", err);
++ return err;
++ }
++ }
++
++ err = request_irq(netdev->irq, gmac_irq,
++ IRQF_SHARED, netdev->name, netdev);
++ if (err) {
++ netdev_err(netdev, "no IRQ\n");
++ return err;
++ }
++
++ netif_carrier_off(netdev);
++ phy_start(netdev->phydev);
++
++ err = geth_resize_freeq(port);
++ if (err) {
++ netdev_err(netdev, "could not resize freeq\n");
++ goto err_stop_phy;
++ }
++
++ err = gmac_setup_rxq(netdev);
++ if (err) {
++ netdev_err(netdev, "could not setup RXQ\n");
++ goto err_stop_phy;
++ }
++
++ err = gmac_setup_txqs(netdev);
++ if (err) {
++ netdev_err(netdev, "could not setup TXQs\n");
++ gmac_cleanup_rxq(netdev);
++ goto err_stop_phy;
++ }
++
++ napi_enable(&port->napi);
++
++ gmac_start_dma(port);
++ gmac_enable_irq(netdev, 1);
++ gmac_enable_tx_rx(netdev);
++ netif_tx_start_all_queues(netdev);
++
++ hrtimer_init(&port->rx_coalesce_timer, CLOCK_MONOTONIC,
++ HRTIMER_MODE_REL);
++ port->rx_coalesce_timer.function = &gmac_coalesce_delay_expired;
++
++ netdev_info(netdev, "opened\n");
++
++ return 0;
++
++err_stop_phy:
++ phy_stop(netdev->phydev);
++ free_irq(netdev->irq, netdev);
++ return err;
++}
++
++static int gmac_stop(struct net_device *netdev)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++
++ hrtimer_cancel(&port->rx_coalesce_timer);
++ netif_tx_stop_all_queues(netdev);
++ gmac_disable_tx_rx(netdev);
++ gmac_stop_dma(port);
++ napi_disable(&port->napi);
++
++ gmac_enable_irq(netdev, 0);
++ gmac_cleanup_rxq(netdev);
++ gmac_cleanup_txqs(netdev);
++
++ phy_stop(netdev->phydev);
++ free_irq(netdev->irq, netdev);
++
++ gmac_update_hw_stats(netdev);
++ return 0;
++}
++
++static void gmac_set_rx_mode(struct net_device *netdev)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ union gmac_rx_fltr filter = { .bits = {
++ .broadcast = 1,
++ .multicast = 1,
++ .unicast = 1,
++ } };
++ struct netdev_hw_addr *ha;
++ unsigned int bit_nr;
++ u32 mc_filter[2];
++
++ mc_filter[1] = 0;
++ mc_filter[0] = 0;
++
++ if (netdev->flags & IFF_PROMISC) {
++ filter.bits.error = 1;
++ filter.bits.promiscuous = 1;
++ mc_filter[1] = ~0;
++ mc_filter[0] = ~0;
++ } else if (netdev->flags & IFF_ALLMULTI) {
++ mc_filter[1] = ~0;
++ mc_filter[0] = ~0;
++ } else {
++ netdev_for_each_mc_addr(ha, netdev) {
++ bit_nr = ~crc32_le(~0, ha->addr, ETH_ALEN) & 0x3f;
++ mc_filter[bit_nr >> 5] |= 1 << (bit_nr & 0x1f);
++ }
++ }
++
++ writel(mc_filter[0], port->gmac_base + GMAC_MCAST_FIL0);
++ writel(mc_filter[1], port->gmac_base + GMAC_MCAST_FIL1);
++ writel(filter.bits32, port->gmac_base + GMAC_RX_FLTR);
++}
++
++static void gmac_write_mac_address(struct net_device *netdev)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ __le32 addr[3];
++
++ memset(addr, 0, sizeof(addr));
++ memcpy(addr, netdev->dev_addr, ETH_ALEN);
++
++ writel(le32_to_cpu(addr[0]), port->gmac_base + GMAC_STA_ADD0);
++ writel(le32_to_cpu(addr[1]), port->gmac_base + GMAC_STA_ADD1);
++ writel(le32_to_cpu(addr[2]), port->gmac_base + GMAC_STA_ADD2);
++}
++
++static int gmac_set_mac_address(struct net_device *netdev, void *addr)
++{
++ struct sockaddr *sa = addr;
++
++ memcpy(netdev->dev_addr, sa->sa_data, ETH_ALEN);
++ gmac_write_mac_address(netdev);
++
++ return 0;
++}
++
++static void gmac_clear_hw_stats(struct net_device *netdev)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++
++ readl(port->gmac_base + GMAC_IN_DISCARDS);
++ readl(port->gmac_base + GMAC_IN_ERRORS);
++ readl(port->gmac_base + GMAC_IN_MCAST);
++ readl(port->gmac_base + GMAC_IN_BCAST);
++ readl(port->gmac_base + GMAC_IN_MAC1);
++ readl(port->gmac_base + GMAC_IN_MAC2);
++}
++
++static void gmac_get_stats64(struct net_device *netdev,
++ struct rtnl_link_stats64 *stats)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ unsigned int start;
++
++ gmac_update_hw_stats(netdev);
++
++ /* Racing with RX NAPI */
++ do {
++ start = u64_stats_fetch_begin(&port->rx_stats_syncp);
++
++ stats->rx_packets = port->stats.rx_packets;
++ stats->rx_bytes = port->stats.rx_bytes;
++ stats->rx_errors = port->stats.rx_errors;
++ stats->rx_dropped = port->stats.rx_dropped;
++
++ stats->rx_length_errors = port->stats.rx_length_errors;
++ stats->rx_over_errors = port->stats.rx_over_errors;
++ stats->rx_crc_errors = port->stats.rx_crc_errors;
++ stats->rx_frame_errors = port->stats.rx_frame_errors;
++
++ } while (u64_stats_fetch_retry(&port->rx_stats_syncp, start));
++
++ /* Racing with MIB and TX completion interrupts */
++ do {
++ start = u64_stats_fetch_begin(&port->ir_stats_syncp);
++
++ stats->tx_errors = port->stats.tx_errors;
++ stats->tx_packets = port->stats.tx_packets;
++ stats->tx_bytes = port->stats.tx_bytes;
++
++ stats->multicast = port->stats.multicast;
++ stats->rx_missed_errors = port->stats.rx_missed_errors;
++ stats->rx_fifo_errors = port->stats.rx_fifo_errors;
++
++ } while (u64_stats_fetch_retry(&port->ir_stats_syncp, start));
++
++ /* Racing with hard_start_xmit */
++ do {
++ start = u64_stats_fetch_begin(&port->tx_stats_syncp);
++
++ stats->tx_dropped = port->stats.tx_dropped;
++
++ } while (u64_stats_fetch_retry(&port->tx_stats_syncp, start));
++
++ stats->rx_dropped += stats->rx_missed_errors;
++}
++
++static int gmac_change_mtu(struct net_device *netdev, int new_mtu)
++{
++ int max_len = gmac_pick_rx_max_len(new_mtu);
++
++ if (max_len < 0)
++ return -EINVAL;
++
++ gmac_disable_tx_rx(netdev);
++
++ netdev->mtu = new_mtu;
++ gmac_update_config0_reg(netdev, max_len << CONFIG0_MAXLEN_SHIFT,
++ CONFIG0_MAXLEN_MASK);
++
++ netdev_update_features(netdev);
++
++ gmac_enable_tx_rx(netdev);
++
++ return 0;
++}
++
++static netdev_features_t gmac_fix_features(struct net_device *netdev,
++ netdev_features_t features)
++{
++ if (netdev->mtu + ETH_HLEN + VLAN_HLEN > MTU_SIZE_BIT_MASK)
++ features &= ~GMAC_OFFLOAD_FEATURES;
++
++ return features;
++}
++
++static int gmac_set_features(struct net_device *netdev,
++ netdev_features_t features)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ int enable = features & NETIF_F_RXCSUM;
++ unsigned long flags;
++ u32 reg;
++
++ spin_lock_irqsave(&port->config_lock, flags);
++
++ reg = readl(port->gmac_base + GMAC_CONFIG0);
++ reg = enable ? reg | CONFIG0_RX_CHKSUM : reg & ~CONFIG0_RX_CHKSUM;
++ writel(reg, port->gmac_base + GMAC_CONFIG0);
++
++ spin_unlock_irqrestore(&port->config_lock, flags);
++ return 0;
++}
++
++static int gmac_get_sset_count(struct net_device *netdev, int sset)
++{
++ return sset == ETH_SS_STATS ? GMAC_STATS_NUM : 0;
++}
++
++static void gmac_get_strings(struct net_device *netdev, u32 stringset, u8 *data)
++{
++ if (stringset != ETH_SS_STATS)
++ return;
++
++ memcpy(data, gmac_stats_strings, sizeof(gmac_stats_strings));
++}
++
++static void gmac_get_ethtool_stats(struct net_device *netdev,
++ struct ethtool_stats *estats, u64 *values)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ unsigned int start;
++ u64 *p;
++ int i;
++
++ gmac_update_hw_stats(netdev);
++
++ /* Racing with MIB interrupt */
++ do {
++ p = values;
++ start = u64_stats_fetch_begin(&port->ir_stats_syncp);
++
++ for (i = 0; i < RX_STATS_NUM; i++)
++ *p++ = port->hw_stats[i];
++
++ } while (u64_stats_fetch_retry(&port->ir_stats_syncp, start));
++ values = p;
++
++ /* Racing with RX NAPI */
++ do {
++ p = values;
++ start = u64_stats_fetch_begin(&port->rx_stats_syncp);
++
++ for (i = 0; i < RX_STATUS_NUM; i++)
++ *p++ = port->rx_stats[i];
++ for (i = 0; i < RX_CHKSUM_NUM; i++)
++ *p++ = port->rx_csum_stats[i];
++ *p++ = port->rx_napi_exits;
++
++ } while (u64_stats_fetch_retry(&port->rx_stats_syncp, start));
++ values = p;
++
++ /* Racing with TX start_xmit */
++ do {
++ p = values;
++ start = u64_stats_fetch_begin(&port->tx_stats_syncp);
++
++ for (i = 0; i < TX_MAX_FRAGS; i++) {
++ *values++ = port->tx_frag_stats[i];
++ port->tx_frag_stats[i] = 0;
++ }
++ *values++ = port->tx_frags_linearized;
++ *values++ = port->tx_hw_csummed;
++
++ } while (u64_stats_fetch_retry(&port->tx_stats_syncp, start));
++}
++
++static int gmac_get_ksettings(struct net_device *netdev,
++ struct ethtool_link_ksettings *cmd)
++{
++ if (!netdev->phydev)
++ return -ENXIO;
++ phy_ethtool_ksettings_get(netdev->phydev, cmd);
++
++ return 0;
++}
++
++static int gmac_set_ksettings(struct net_device *netdev,
++ const struct ethtool_link_ksettings *cmd)
++{
++ if (!netdev->phydev)
++ return -ENXIO;
++ return phy_ethtool_ksettings_set(netdev->phydev, cmd);
++}
++
++static int gmac_nway_reset(struct net_device *netdev)
++{
++ if (!netdev->phydev)
++ return -ENXIO;
++ return phy_start_aneg(netdev->phydev);
++}
++
++static void gmac_get_pauseparam(struct net_device *netdev,
++ struct ethtool_pauseparam *pparam)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ union gmac_config0 config0;
++
++ config0.bits32 = readl(port->gmac_base + GMAC_CONFIG0);
++
++ pparam->rx_pause = config0.bits.rx_fc_en;
++ pparam->tx_pause = config0.bits.tx_fc_en;
++ pparam->autoneg = true;
++}
++
++static void gmac_get_ringparam(struct net_device *netdev,
++ struct ethtool_ringparam *rp)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ union gmac_config0 config0;
++
++ config0.bits32 = readl(port->gmac_base + GMAC_CONFIG0);
++
++ rp->rx_max_pending = 1 << 15;
++ rp->rx_mini_max_pending = 0;
++ rp->rx_jumbo_max_pending = 0;
++ rp->tx_max_pending = 1 << 15;
++
++ rp->rx_pending = 1 << port->rxq_order;
++ rp->rx_mini_pending = 0;
++ rp->rx_jumbo_pending = 0;
++ rp->tx_pending = 1 << port->txq_order;
++}
++
++static int gmac_set_ringparam(struct net_device *netdev,
++ struct ethtool_ringparam *rp)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++ int err = 0;
++
++ if (netif_running(netdev))
++ return -EBUSY;
++
++ if (rp->rx_pending) {
++ port->rxq_order = min(15, ilog2(rp->rx_pending - 1) + 1);
++ err = geth_resize_freeq(port);
++ }
++ if (rp->tx_pending) {
++ port->txq_order = min(15, ilog2(rp->tx_pending - 1) + 1);
++ port->irq_every_tx_packets = 1 << (port->txq_order - 2);
++ }
++
++ return err;
++}
++
++static int gmac_get_coalesce(struct net_device *netdev,
++ struct ethtool_coalesce *ecmd)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++
++ ecmd->rx_max_coalesced_frames = 1;
++ ecmd->tx_max_coalesced_frames = port->irq_every_tx_packets;
++ ecmd->rx_coalesce_usecs = port->rx_coalesce_nsecs / 1000;
++
++ return 0;
++}
++
++static int gmac_set_coalesce(struct net_device *netdev,
++ struct ethtool_coalesce *ecmd)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++
++ if (ecmd->tx_max_coalesced_frames < 1)
++ return -EINVAL;
++ if (ecmd->tx_max_coalesced_frames >= 1 << port->txq_order)
++ return -EINVAL;
++
++ port->irq_every_tx_packets = ecmd->tx_max_coalesced_frames;
++ port->rx_coalesce_nsecs = ecmd->rx_coalesce_usecs * 1000;
++
++ return 0;
++}
++
++static u32 gmac_get_msglevel(struct net_device *netdev)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++
++ return port->msg_enable;
++}
++
++static void gmac_set_msglevel(struct net_device *netdev, u32 level)
++{
++ struct gemini_ethernet_port *port = netdev_priv(netdev);
++
++ port->msg_enable = level;
++}
++
++static void gmac_get_drvinfo(struct net_device *netdev,
++ struct ethtool_drvinfo *info)
++{
++ strcpy(info->driver, DRV_NAME);
++ strcpy(info->version, DRV_VERSION);
++ strcpy(info->bus_info, netdev->dev_id ? "1" : "0");
++}
++
++static const struct net_device_ops gmac_351x_ops = {
++ .ndo_init = gmac_init,
++ .ndo_uninit = gmac_uninit,
++ .ndo_open = gmac_open,
++ .ndo_stop = gmac_stop,
++ .ndo_start_xmit = gmac_start_xmit,
++ .ndo_tx_timeout = gmac_tx_timeout,
++ .ndo_set_rx_mode = gmac_set_rx_mode,
++ .ndo_set_mac_address = gmac_set_mac_address,
++ .ndo_get_stats64 = gmac_get_stats64,
++ .ndo_change_mtu = gmac_change_mtu,
++ .ndo_fix_features = gmac_fix_features,
++ .ndo_set_features = gmac_set_features,
++};
++
++static const struct ethtool_ops gmac_351x_ethtool_ops = {
++ .get_sset_count = gmac_get_sset_count,
++ .get_strings = gmac_get_strings,
++ .get_ethtool_stats = gmac_get_ethtool_stats,
++ .get_link = ethtool_op_get_link,
++ .get_link_ksettings = gmac_get_ksettings,
++ .set_link_ksettings = gmac_set_ksettings,
++ .nway_reset = gmac_nway_reset,
++ .get_pauseparam = gmac_get_pauseparam,
++ .get_ringparam = gmac_get_ringparam,
++ .set_ringparam = gmac_set_ringparam,
++ .get_coalesce = gmac_get_coalesce,
++ .set_coalesce = gmac_set_coalesce,
++ .get_msglevel = gmac_get_msglevel,
++ .set_msglevel = gmac_set_msglevel,
++ .get_drvinfo = gmac_get_drvinfo,
++};
++
++static irqreturn_t gemini_port_irq_thread(int irq, void *data)
++{
++ unsigned long irqmask = SWFQ_EMPTY_INT_BIT;
++ struct gemini_ethernet_port *port = data;
++ struct gemini_ethernet *geth;
++ unsigned long flags;
++
++ geth = port->geth;
++ /* The queue is half empty so refill it */
++ geth_fill_freeq(geth, true);
++
++ spin_lock_irqsave(&geth->irq_lock, flags);
++ /* ACK queue interrupt */
++ writel(irqmask, geth->base + GLOBAL_INTERRUPT_STATUS_4_REG);
++ /* Enable queue interrupt again */
++ irqmask |= readl(geth->base + GLOBAL_INTERRUPT_ENABLE_4_REG);
++ writel(irqmask, geth->base + GLOBAL_INTERRUPT_ENABLE_4_REG);
++ spin_unlock_irqrestore(&geth->irq_lock, flags);
++
++ return IRQ_HANDLED;
++}
++
++static irqreturn_t gemini_port_irq(int irq, void *data)
++{
++ struct gemini_ethernet_port *port = data;
++ struct gemini_ethernet *geth;
++ irqreturn_t ret = IRQ_NONE;
++ u32 val, en;
++
++ geth = port->geth;
++ spin_lock(&geth->irq_lock);
++
++ val = readl(geth->base + GLOBAL_INTERRUPT_STATUS_4_REG);
++ en = readl(geth->base + GLOBAL_INTERRUPT_ENABLE_4_REG);
++
++ if (val & en & SWFQ_EMPTY_INT_BIT) {
++ /* Disable the queue empty interrupt while we work on
++ * processing the queue. Also disable overrun interrupts
++ * as there is not much we can do about it here.
++ */
++ en &= ~(SWFQ_EMPTY_INT_BIT | GMAC0_RX_OVERRUN_INT_BIT
++ | GMAC1_RX_OVERRUN_INT_BIT);
++ writel(en, geth->base + GLOBAL_INTERRUPT_ENABLE_4_REG);
++ ret = IRQ_WAKE_THREAD;
++ }
++
++ spin_unlock(&geth->irq_lock);
++
++ return ret;
++}
++
++static void gemini_port_remove(struct gemini_ethernet_port *port)
++{
++ if (port->netdev)
++ unregister_netdev(port->netdev);
++ clk_disable_unprepare(port->pclk);
++ geth_cleanup_freeq(port->geth);
++}
++
++static void gemini_ethernet_init(struct gemini_ethernet *geth)
++{
++ writel(0, geth->base + GLOBAL_INTERRUPT_ENABLE_0_REG);
++ writel(0, geth->base + GLOBAL_INTERRUPT_ENABLE_1_REG);
++ writel(0, geth->base + GLOBAL_INTERRUPT_ENABLE_2_REG);
++ writel(0, geth->base + GLOBAL_INTERRUPT_ENABLE_3_REG);
++ writel(0, geth->base + GLOBAL_INTERRUPT_ENABLE_4_REG);
++
++ /* Interrupt config:
++ *
++ * GMAC0 intr bits ------> int0 ----> eth0
++ * GMAC1 intr bits ------> int1 ----> eth1
++ * TOE intr -------------> int1 ----> eth1
++ * Classification Intr --> int0 ----> eth0
++ * Default Q0 -----------> int0 ----> eth0
++ * Default Q1 -----------> int1 ----> eth1
++ * FreeQ intr -----------> int1 ----> eth1
++ */
++ writel(0xCCFC0FC0, geth->base + GLOBAL_INTERRUPT_SELECT_0_REG);
++ writel(0x00F00002, geth->base + GLOBAL_INTERRUPT_SELECT_1_REG);
++ writel(0xFFFFFFFF, geth->base + GLOBAL_INTERRUPT_SELECT_2_REG);
++ writel(0xFFFFFFFF, geth->base + GLOBAL_INTERRUPT_SELECT_3_REG);
++ writel(0xFF000003, geth->base + GLOBAL_INTERRUPT_SELECT_4_REG);
++
++ /* edge-triggered interrupts packed to level-triggered one... */
++ writel(~0, geth->base + GLOBAL_INTERRUPT_STATUS_0_REG);
++ writel(~0, geth->base + GLOBAL_INTERRUPT_STATUS_1_REG);
++ writel(~0, geth->base + GLOBAL_INTERRUPT_STATUS_2_REG);
++ writel(~0, geth->base + GLOBAL_INTERRUPT_STATUS_3_REG);
++ writel(~0, geth->base + GLOBAL_INTERRUPT_STATUS_4_REG);
++
++ /* Set up queue */
++ writel(0, geth->base + GLOBAL_SW_FREEQ_BASE_SIZE_REG);
++ writel(0, geth->base + GLOBAL_HW_FREEQ_BASE_SIZE_REG);
++ writel(0, geth->base + GLOBAL_SWFQ_RWPTR_REG);
++ writel(0, geth->base + GLOBAL_HWFQ_RWPTR_REG);
++
++ geth->freeq_frag_order = DEFAULT_RX_BUF_ORDER;
++ /* This makes the queue resize on probe() so that we
++ * set up and enable the queue IRQ. FIXME: fragile.
++ */
++ geth->freeq_order = 1;
++}
++
++static void gemini_port_save_mac_addr(struct gemini_ethernet_port *port)
++{
++ port->mac_addr[0] =
++ cpu_to_le32(readl(port->gmac_base + GMAC_STA_ADD0));
++ port->mac_addr[1] =
++ cpu_to_le32(readl(port->gmac_base + GMAC_STA_ADD1));
++ port->mac_addr[2] =
++ cpu_to_le32(readl(port->gmac_base + GMAC_STA_ADD2));
++}
++
++static int gemini_ethernet_port_probe(struct platform_device *pdev)
++{
++ char *port_names[2] = { "ethernet0", "ethernet1" };
++ struct gemini_ethernet_port *port;
++ struct device *dev = &pdev->dev;
++ struct gemini_ethernet *geth;
++ struct net_device *netdev;
++ struct resource *gmacres;
++ struct resource *dmares;
++ struct device *parent;
++ unsigned int id;
++ int irq;
++ int ret;
++
++ parent = dev->parent;
++ geth = dev_get_drvdata(parent);
++
++ if (!strcmp(dev_name(dev), "60008000.ethernet-port"))
++ id = 0;
++ else if (!strcmp(dev_name(dev), "6000c000.ethernet-port"))
++ id = 1;
++ else
++ return -ENODEV;
++
++ dev_info(dev, "probe %s ID %d\n", dev_name(dev), id);
++
++ netdev = alloc_etherdev_mq(sizeof(*port), TX_QUEUE_NUM);
++ if (!netdev) {
++ dev_err(dev, "Can't allocate ethernet device #%d\n", id);
++ return -ENOMEM;
++ }
++
++ port = netdev_priv(netdev);
++ SET_NETDEV_DEV(netdev, dev);
++ port->netdev = netdev;
++ port->id = id;
++ port->geth = geth;
++ port->dev = dev;
++
++ /* DMA memory */
++ dmares = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++ if (!dmares) {
++ dev_err(dev, "no DMA resource\n");
++ return -ENODEV;
++ }
++ port->dma_base = devm_ioremap_resource(dev, dmares);
++ if (IS_ERR(port->dma_base))
++ return PTR_ERR(port->dma_base);
++
++ /* GMAC config memory */
++ gmacres = platform_get_resource(pdev, IORESOURCE_MEM, 1);
++ if (!gmacres) {
++ dev_err(dev, "no GMAC resource\n");
++ return -ENODEV;
++ }
++ port->gmac_base = devm_ioremap_resource(dev, gmacres);
++ if (IS_ERR(port->gmac_base))
++ return PTR_ERR(port->gmac_base);
++
++ /* Interrupt */
++ irq = platform_get_irq(pdev, 0);
++ if (irq <= 0) {
++ dev_err(dev, "no IRQ\n");
++ return irq ? irq : -ENODEV;
++ }
++ port->irq = irq;
++
++ /* Clock the port */
++ port->pclk = devm_clk_get(dev, "PCLK");
++ if (IS_ERR(port->pclk)) {
++ dev_err(dev, "no PCLK\n");
++ return PTR_ERR(port->pclk);
++ }
++ ret = clk_prepare_enable(port->pclk);
++ if (ret)
++ return ret;
++
++ /* Maybe there is a nice ethernet address we should use */
++ gemini_port_save_mac_addr(port);
++
++ /* Reset the port */
++ port->reset = devm_reset_control_get_exclusive(dev, NULL);
++ if (IS_ERR(port->reset)) {
++ dev_err(dev, "no reset\n");
++ return PTR_ERR(port->reset);
++ }
++ reset_control_reset(port->reset);
++ usleep_range(100, 500);
++
++ /* Assign pointer in the main state container */
++ if (!id)
++ geth->port0 = port;
++ else
++ geth->port1 = port;
++ platform_set_drvdata(pdev, port);
++
++ /* Set up and register the netdev */
++ netdev->dev_id = port->id;
++ netdev->irq = irq;
++ netdev->netdev_ops = &gmac_351x_ops;
++ netdev->ethtool_ops = &gmac_351x_ethtool_ops;
++
++ spin_lock_init(&port->config_lock);
++ gmac_clear_hw_stats(netdev);
++
++ netdev->hw_features = GMAC_OFFLOAD_FEATURES;
++ netdev->features |= GMAC_OFFLOAD_FEATURES | NETIF_F_GRO;
++
++ port->freeq_refill = 0;
++ netif_napi_add(netdev, &port->napi, gmac_napi_poll,
++ DEFAULT_NAPI_WEIGHT);
++
++ if (is_valid_ether_addr((void *)port->mac_addr)) {
++ memcpy(netdev->dev_addr, port->mac_addr, ETH_ALEN);
++ } else {
++ dev_dbg(dev, "ethernet address 0x%08x%08x%08x invalid\n",
++ port->mac_addr[0], port->mac_addr[1],
++ port->mac_addr[2]);
++ dev_info(dev, "using a random ethernet address\n");
++ random_ether_addr(netdev->dev_addr);
++ }
++ gmac_write_mac_address(netdev);
++
++ ret = devm_request_threaded_irq(port->dev,
++ port->irq,
++ gemini_port_irq,
++ gemini_port_irq_thread,
++ IRQF_SHARED,
++ port_names[port->id],
++ port);
++ if (ret)
++ return ret;
++
++ ret = register_netdev(netdev);
++ if (!ret) {
++ netdev_info(netdev,
++ "irq %d, DMA @ 0x%pap, GMAC @ 0x%pap\n",
++ port->irq, &dmares->start,
++ &gmacres->start);
++ ret = gmac_setup_phy(netdev);
++ if (ret)
++ netdev_info(netdev,
++ "PHY init failed, deferring to ifup time\n");
++ return 0;
++ }
++
++ port->netdev = NULL;
++ free_netdev(netdev);
++ return ret;
++}
++
++static int gemini_ethernet_port_remove(struct platform_device *pdev)
++{
++ struct gemini_ethernet_port *port = platform_get_drvdata(pdev);
++
++ gemini_port_remove(port);
++ return 0;
++}
++
++static const struct of_device_id gemini_ethernet_port_of_match[] = {
++ {
++ .compatible = "cortina,gemini-ethernet-port",
++ },
++ {},
++};
++MODULE_DEVICE_TABLE(of, gemini_ethernet_port_of_match);
++
++static struct platform_driver gemini_ethernet_port_driver = {
++ .driver = {
++ .name = "gemini-ethernet-port",
++ .of_match_table = of_match_ptr(gemini_ethernet_port_of_match),
++ },
++ .probe = gemini_ethernet_port_probe,
++ .remove = gemini_ethernet_port_remove,
++};
++
++static int gemini_ethernet_probe(struct platform_device *pdev)
++{
++ struct device *dev = &pdev->dev;
++ struct gemini_ethernet *geth;
++ unsigned int retry = 5;
++ struct resource *res;
++ u32 val;
++
++ /* Global registers */
++ geth = devm_kzalloc(dev, sizeof(*geth), GFP_KERNEL);
++ if (!geth)
++ return -ENOMEM;
++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++ if (!res)
++ return -ENODEV;
++ geth->base = devm_ioremap_resource(dev, res);
++ if (IS_ERR(geth->base))
++ return PTR_ERR(geth->base);
++ geth->dev = dev;
++
++ /* Wait for ports to stabilize */
++ do {
++ udelay(2);
++ val = readl(geth->base + GLOBAL_TOE_VERSION_REG);
++ barrier();
++ } while (!val && --retry);
++ if (!retry) {
++ dev_err(dev, "failed to reset ethernet\n");
++ return -EIO;
++ }
++ dev_info(dev, "Ethernet device ID: 0x%03x, revision 0x%01x\n",
++ (val >> 4) & 0xFFFU, val & 0xFU);
++
++ spin_lock_init(&geth->irq_lock);
++ spin_lock_init(&geth->freeq_lock);
++ gemini_ethernet_init(geth);
++
++ /* The children will use this */
++ platform_set_drvdata(pdev, geth);
++
++ /* Spawn child devices for the two ports */
++ return devm_of_platform_populate(dev);
++}
++
++static int gemini_ethernet_remove(struct platform_device *pdev)
++{
++ struct gemini_ethernet *geth = platform_get_drvdata(pdev);
++
++ gemini_ethernet_init(geth);
++ geth_cleanup_freeq(geth);
++
++ return 0;
++}
++
++static const struct of_device_id gemini_ethernet_of_match[] = {
++ {
++ .compatible = "cortina,gemini-ethernet",
++ },
++ {},
++};
++MODULE_DEVICE_TABLE(of, gemini_ethernet_of_match);
++
++static struct platform_driver gemini_ethernet_driver = {
++ .driver = {
++ .name = DRV_NAME,
++ .of_match_table = of_match_ptr(gemini_ethernet_of_match),
++ },
++ .probe = gemini_ethernet_probe,
++ .remove = gemini_ethernet_remove,
++};
++
++static int __init gemini_ethernet_module_init(void)
++{
++ int ret;
++
++ ret = platform_driver_register(&gemini_ethernet_port_driver);
++ if (ret)
++ return ret;
++
++ ret = platform_driver_register(&gemini_ethernet_driver);
++ if (ret) {
++ platform_driver_unregister(&gemini_ethernet_port_driver);
++ return ret;
++ }
++
++ return 0;
++}
++module_init(gemini_ethernet_module_init);
++
++static void __exit gemini_ethernet_module_exit(void)
++{
++ platform_driver_unregister(&gemini_ethernet_driver);
++ platform_driver_unregister(&gemini_ethernet_port_driver);
++}
++module_exit(gemini_ethernet_module_exit);
++
++MODULE_AUTHOR("Linus Walleij <linus.walleij at linaro.org>");
++MODULE_DESCRIPTION("StorLink SL351x (Gemini) ethernet driver");
++MODULE_LICENSE("GPL");
++MODULE_ALIAS("platform:" DRV_NAME);
+--- /dev/null
++++ b/drivers/net/ethernet/cortina/gemini.h
+@@ -0,0 +1,958 @@
++// SPDX-License-Identifier: GPL-2.0
++/* Register definitions for Gemini GMAC Ethernet device driver
++ *
++ * Copyright (C) 2006 Storlink, Corp.
++ * Copyright (C) 2008-2009 Paulius Zaleckas <paulius.zaleckas at teltonika.lt>
++ * Copyright (C) 2010 Michał Mirosław <mirq-linux at rere.qmqm.pl>
++ * Copytight (C) 2017 Linus Walleij <linus.walleij at linaro.org>
++ */
++#ifndef _GEMINI_ETHERNET_H
++#define _GEMINI_ETHERNET_H
++
++#include <linux/bitops.h>
++
++/* Base Registers */
++#define TOE_NONTOE_QUE_HDR_BASE 0x2000
++#define TOE_TOE_QUE_HDR_BASE 0x3000
++
++/* Queue ID */
++#define TOE_SW_FREE_QID 0x00
++#define TOE_HW_FREE_QID 0x01
++#define TOE_GMAC0_SW_TXQ0_QID 0x02
++#define TOE_GMAC0_SW_TXQ1_QID 0x03
++#define TOE_GMAC0_SW_TXQ2_QID 0x04
++#define TOE_GMAC0_SW_TXQ3_QID 0x05
++#define TOE_GMAC0_SW_TXQ4_QID 0x06
++#define TOE_GMAC0_SW_TXQ5_QID 0x07
++#define TOE_GMAC0_HW_TXQ0_QID 0x08
++#define TOE_GMAC0_HW_TXQ1_QID 0x09
++#define TOE_GMAC0_HW_TXQ2_QID 0x0A
++#define TOE_GMAC0_HW_TXQ3_QID 0x0B
++#define TOE_GMAC1_SW_TXQ0_QID 0x12
++#define TOE_GMAC1_SW_TXQ1_QID 0x13
++#define TOE_GMAC1_SW_TXQ2_QID 0x14
++#define TOE_GMAC1_SW_TXQ3_QID 0x15
++#define TOE_GMAC1_SW_TXQ4_QID 0x16
++#define TOE_GMAC1_SW_TXQ5_QID 0x17
++#define TOE_GMAC1_HW_TXQ0_QID 0x18
++#define TOE_GMAC1_HW_TXQ1_QID 0x19
++#define TOE_GMAC1_HW_TXQ2_QID 0x1A
++#define TOE_GMAC1_HW_TXQ3_QID 0x1B
++#define TOE_GMAC0_DEFAULT_QID 0x20
++#define TOE_GMAC1_DEFAULT_QID 0x21
++#define TOE_CLASSIFICATION_QID(x) (0x22 + x) /* 0x22 ~ 0x2F */
++#define TOE_TOE_QID(x) (0x40 + x) /* 0x40 ~ 0x7F */
++
++/* TOE DMA Queue Size should be 2^n, n = 6...12
++ * TOE DMA Queues are the following queue types:
++ * SW Free Queue, HW Free Queue,
++ * GMAC 0/1 SW TX Q0-5, and GMAC 0/1 HW TX Q0-5
++ * The base address and descriptor number are configured at
++ * DMA Queues Descriptor Ring Base Address/Size Register (offset 0x0004)
++ */
++#define GET_WPTR(addr) readw((addr) + 2)
++#define GET_RPTR(addr) readw((addr))
++#define SET_WPTR(addr, data) writew((data), (addr) + 2)
++#define SET_RPTR(addr, data) writew((data), (addr))
++#define __RWPTR_NEXT(x, mask) (((unsigned int)(x) + 1) & (mask))
++#define __RWPTR_PREV(x, mask) (((unsigned int)(x) - 1) & (mask))
++#define __RWPTR_DISTANCE(r, w, mask) (((unsigned int)(w) - (r)) & (mask))
++#define __RWPTR_MASK(order) ((1 << (order)) - 1)
++#define RWPTR_NEXT(x, order) __RWPTR_NEXT((x), __RWPTR_MASK((order)))
++#define RWPTR_PREV(x, order) __RWPTR_PREV((x), __RWPTR_MASK((order)))
++#define RWPTR_DISTANCE(r, w, order) __RWPTR_DISTANCE((r), (w), \
++ __RWPTR_MASK((order)))
++
++/* Global registers */
++#define GLOBAL_TOE_VERSION_REG 0x0000
++#define GLOBAL_SW_FREEQ_BASE_SIZE_REG 0x0004
++#define GLOBAL_HW_FREEQ_BASE_SIZE_REG 0x0008
++#define GLOBAL_DMA_SKB_SIZE_REG 0x0010
++#define GLOBAL_SWFQ_RWPTR_REG 0x0014
++#define GLOBAL_HWFQ_RWPTR_REG 0x0018
++#define GLOBAL_INTERRUPT_STATUS_0_REG 0x0020
++#define GLOBAL_INTERRUPT_ENABLE_0_REG 0x0024
++#define GLOBAL_INTERRUPT_SELECT_0_REG 0x0028
++#define GLOBAL_INTERRUPT_STATUS_1_REG 0x0030
++#define GLOBAL_INTERRUPT_ENABLE_1_REG 0x0034
++#define GLOBAL_INTERRUPT_SELECT_1_REG 0x0038
++#define GLOBAL_INTERRUPT_STATUS_2_REG 0x0040
++#define GLOBAL_INTERRUPT_ENABLE_2_REG 0x0044
++#define GLOBAL_INTERRUPT_SELECT_2_REG 0x0048
++#define GLOBAL_INTERRUPT_STATUS_3_REG 0x0050
++#define GLOBAL_INTERRUPT_ENABLE_3_REG 0x0054
++#define GLOBAL_INTERRUPT_SELECT_3_REG 0x0058
++#define GLOBAL_INTERRUPT_STATUS_4_REG 0x0060
++#define GLOBAL_INTERRUPT_ENABLE_4_REG 0x0064
++#define GLOBAL_INTERRUPT_SELECT_4_REG 0x0068
++#define GLOBAL_HASH_TABLE_BASE_REG 0x006C
++#define GLOBAL_QUEUE_THRESHOLD_REG 0x0070
++
++/* GMAC 0/1 DMA/TOE register */
++#define GMAC_DMA_CTRL_REG 0x0000
++#define GMAC_TX_WEIGHTING_CTRL_0_REG 0x0004
++#define GMAC_TX_WEIGHTING_CTRL_1_REG 0x0008
++#define GMAC_SW_TX_QUEUE0_PTR_REG 0x000C
++#define GMAC_SW_TX_QUEUE1_PTR_REG 0x0010
++#define GMAC_SW_TX_QUEUE2_PTR_REG 0x0014
++#define GMAC_SW_TX_QUEUE3_PTR_REG 0x0018
++#define GMAC_SW_TX_QUEUE4_PTR_REG 0x001C
++#define GMAC_SW_TX_QUEUE5_PTR_REG 0x0020
++#define GMAC_SW_TX_QUEUE_PTR_REG(i) (GMAC_SW_TX_QUEUE0_PTR_REG + 4 * (i))
++#define GMAC_HW_TX_QUEUE0_PTR_REG 0x0024
++#define GMAC_HW_TX_QUEUE1_PTR_REG 0x0028
++#define GMAC_HW_TX_QUEUE2_PTR_REG 0x002C
++#define GMAC_HW_TX_QUEUE3_PTR_REG 0x0030
++#define GMAC_HW_TX_QUEUE_PTR_REG(i) (GMAC_HW_TX_QUEUE0_PTR_REG + 4 * (i))
++#define GMAC_DMA_TX_FIRST_DESC_REG 0x0038
++#define GMAC_DMA_TX_CURR_DESC_REG 0x003C
++#define GMAC_DMA_TX_DESC_WORD0_REG 0x0040
++#define GMAC_DMA_TX_DESC_WORD1_REG 0x0044
++#define GMAC_DMA_TX_DESC_WORD2_REG 0x0048
++#define GMAC_DMA_TX_DESC_WORD3_REG 0x004C
++#define GMAC_SW_TX_QUEUE_BASE_REG 0x0050
++#define GMAC_HW_TX_QUEUE_BASE_REG 0x0054
++#define GMAC_DMA_RX_FIRST_DESC_REG 0x0058
++#define GMAC_DMA_RX_CURR_DESC_REG 0x005C
++#define GMAC_DMA_RX_DESC_WORD0_REG 0x0060
++#define GMAC_DMA_RX_DESC_WORD1_REG 0x0064
++#define GMAC_DMA_RX_DESC_WORD2_REG 0x0068
++#define GMAC_DMA_RX_DESC_WORD3_REG 0x006C
++#define GMAC_HASH_ENGINE_REG0 0x0070
++#define GMAC_HASH_ENGINE_REG1 0x0074
++/* matching rule 0 Control register 0 */
++#define GMAC_MR0CR0 0x0078
++#define GMAC_MR0CR1 0x007C
++#define GMAC_MR0CR2 0x0080
++#define GMAC_MR1CR0 0x0084
++#define GMAC_MR1CR1 0x0088
++#define GMAC_MR1CR2 0x008C
++#define GMAC_MR2CR0 0x0090
++#define GMAC_MR2CR1 0x0094
++#define GMAC_MR2CR2 0x0098
++#define GMAC_MR3CR0 0x009C
++#define GMAC_MR3CR1 0x00A0
++#define GMAC_MR3CR2 0x00A4
++/* Support Protocol Register 0 */
++#define GMAC_SPR0 0x00A8
++#define GMAC_SPR1 0x00AC
++#define GMAC_SPR2 0x00B0
++#define GMAC_SPR3 0x00B4
++#define GMAC_SPR4 0x00B8
++#define GMAC_SPR5 0x00BC
++#define GMAC_SPR6 0x00C0
++#define GMAC_SPR7 0x00C4
++/* GMAC Hash/Rx/Tx AHB Weighting register */
++#define GMAC_AHB_WEIGHT_REG 0x00C8
++
++/* TOE GMAC 0/1 register */
++#define GMAC_STA_ADD0 0x0000
++#define GMAC_STA_ADD1 0x0004
++#define GMAC_STA_ADD2 0x0008
++#define GMAC_RX_FLTR 0x000c
++#define GMAC_MCAST_FIL0 0x0010
++#define GMAC_MCAST_FIL1 0x0014
++#define GMAC_CONFIG0 0x0018
++#define GMAC_CONFIG1 0x001c
++#define GMAC_CONFIG2 0x0020
++#define GMAC_CONFIG3 0x0024
++#define GMAC_RESERVED 0x0028
++#define GMAC_STATUS 0x002c
++#define GMAC_IN_DISCARDS 0x0030
++#define GMAC_IN_ERRORS 0x0034
++#define GMAC_IN_MCAST 0x0038
++#define GMAC_IN_BCAST 0x003c
++#define GMAC_IN_MAC1 0x0040 /* for STA 1 MAC Address */
++#define GMAC_IN_MAC2 0x0044 /* for STA 2 MAC Address */
++
++#define RX_STATS_NUM 6
++
++/* DMA Queues description Ring Base Address/Size Register (offset 0x0004) */
++union dma_q_base_size {
++ unsigned int bits32;
++ unsigned int base_size;
++};
++
++#define DMA_Q_BASE_MASK (~0x0f)
++
++/* DMA SKB Buffer register (offset 0x0008) */
++union dma_skb_size {
++ unsigned int bits32;
++ struct bit_0008 {
++ unsigned int sw_skb_size : 16; /* SW Free poll SKB Size */
++ unsigned int hw_skb_size : 16; /* HW Free poll SKB Size */
++ } bits;
++};
++
++/* DMA SW Free Queue Read/Write Pointer Register (offset 0x000c) */
++union dma_rwptr {
++ unsigned int bits32;
++ struct bit_000c {
++ unsigned int rptr : 16; /* Read Ptr, RO */
++ unsigned int wptr : 16; /* Write Ptr, RW */
++ } bits;
++};
++
++/* Interrupt Status Register 0 (offset 0x0020)
++ * Interrupt Mask Register 0 (offset 0x0024)
++ * Interrupt Select Register 0 (offset 0x0028)
++ */
++#define GMAC1_TXDERR_INT_BIT BIT(31)
++#define GMAC1_TXPERR_INT_BIT BIT(30)
++#define GMAC0_TXDERR_INT_BIT BIT(29)
++#define GMAC0_TXPERR_INT_BIT BIT(28)
++#define GMAC1_RXDERR_INT_BIT BIT(27)
++#define GMAC1_RXPERR_INT_BIT BIT(26)
++#define GMAC0_RXDERR_INT_BIT BIT(25)
++#define GMAC0_RXPERR_INT_BIT BIT(24)
++#define GMAC1_SWTQ15_FIN_INT_BIT BIT(23)
++#define GMAC1_SWTQ14_FIN_INT_BIT BIT(22)
++#define GMAC1_SWTQ13_FIN_INT_BIT BIT(21)
++#define GMAC1_SWTQ12_FIN_INT_BIT BIT(20)
++#define GMAC1_SWTQ11_FIN_INT_BIT BIT(19)
++#define GMAC1_SWTQ10_FIN_INT_BIT BIT(18)
++#define GMAC0_SWTQ05_FIN_INT_BIT BIT(17)
++#define GMAC0_SWTQ04_FIN_INT_BIT BIT(16)
++#define GMAC0_SWTQ03_FIN_INT_BIT BIT(15)
++#define GMAC0_SWTQ02_FIN_INT_BIT BIT(14)
++#define GMAC0_SWTQ01_FIN_INT_BIT BIT(13)
++#define GMAC0_SWTQ00_FIN_INT_BIT BIT(12)
++#define GMAC1_SWTQ15_EOF_INT_BIT BIT(11)
++#define GMAC1_SWTQ14_EOF_INT_BIT BIT(10)
++#define GMAC1_SWTQ13_EOF_INT_BIT BIT(9)
++#define GMAC1_SWTQ12_EOF_INT_BIT BIT(8)
++#define GMAC1_SWTQ11_EOF_INT_BIT BIT(7)
++#define GMAC1_SWTQ10_EOF_INT_BIT BIT(6)
++#define GMAC0_SWTQ05_EOF_INT_BIT BIT(5)
++#define GMAC0_SWTQ04_EOF_INT_BIT BIT(4)
++#define GMAC0_SWTQ03_EOF_INT_BIT BIT(3)
++#define GMAC0_SWTQ02_EOF_INT_BIT BIT(2)
++#define GMAC0_SWTQ01_EOF_INT_BIT BIT(1)
++#define GMAC0_SWTQ00_EOF_INT_BIT BIT(0)
++
++/* Interrupt Status Register 1 (offset 0x0030)
++ * Interrupt Mask Register 1 (offset 0x0034)
++ * Interrupt Select Register 1 (offset 0x0038)
++ */
++#define TOE_IQ3_FULL_INT_BIT BIT(31)
++#define TOE_IQ2_FULL_INT_BIT BIT(30)
++#define TOE_IQ1_FULL_INT_BIT BIT(29)
++#define TOE_IQ0_FULL_INT_BIT BIT(28)
++#define TOE_IQ3_INT_BIT BIT(27)
++#define TOE_IQ2_INT_BIT BIT(26)
++#define TOE_IQ1_INT_BIT BIT(25)
++#define TOE_IQ0_INT_BIT BIT(24)
++#define GMAC1_HWTQ13_EOF_INT_BIT BIT(23)
++#define GMAC1_HWTQ12_EOF_INT_BIT BIT(22)
++#define GMAC1_HWTQ11_EOF_INT_BIT BIT(21)
++#define GMAC1_HWTQ10_EOF_INT_BIT BIT(20)
++#define GMAC0_HWTQ03_EOF_INT_BIT BIT(19)
++#define GMAC0_HWTQ02_EOF_INT_BIT BIT(18)
++#define GMAC0_HWTQ01_EOF_INT_BIT BIT(17)
++#define GMAC0_HWTQ00_EOF_INT_BIT BIT(16)
++#define CLASS_RX_INT_BIT(x) BIT((x + 2))
++#define DEFAULT_Q1_INT_BIT BIT(1)
++#define DEFAULT_Q0_INT_BIT BIT(0)
++
++#define TOE_IQ_INT_BITS (TOE_IQ0_INT_BIT | TOE_IQ1_INT_BIT | \
++ TOE_IQ2_INT_BIT | TOE_IQ3_INT_BIT)
++#define TOE_IQ_FULL_BITS (TOE_IQ0_FULL_INT_BIT | TOE_IQ1_FULL_INT_BIT | \
++ TOE_IQ2_FULL_INT_BIT | TOE_IQ3_FULL_INT_BIT)
++#define TOE_IQ_ALL_BITS (TOE_IQ_INT_BITS | TOE_IQ_FULL_BITS)
++#define TOE_CLASS_RX_INT_BITS 0xfffc
++
++/* Interrupt Status Register 2 (offset 0x0040)
++ * Interrupt Mask Register 2 (offset 0x0044)
++ * Interrupt Select Register 2 (offset 0x0048)
++ */
++#define TOE_QL_FULL_INT_BIT(x) BIT(x)
++
++/* Interrupt Status Register 3 (offset 0x0050)
++ * Interrupt Mask Register 3 (offset 0x0054)
++ * Interrupt Select Register 3 (offset 0x0058)
++ */
++#define TOE_QH_FULL_INT_BIT(x) BIT(x - 32)
++
++/* Interrupt Status Register 4 (offset 0x0060)
++ * Interrupt Mask Register 4 (offset 0x0064)
++ * Interrupt Select Register 4 (offset 0x0068)
++ */
++#define GMAC1_RESERVED_INT_BIT BIT(31)
++#define GMAC1_MIB_INT_BIT BIT(30)
++#define GMAC1_RX_PAUSE_ON_INT_BIT BIT(29)
++#define GMAC1_TX_PAUSE_ON_INT_BIT BIT(28)
++#define GMAC1_RX_PAUSE_OFF_INT_BIT BIT(27)
++#define GMAC1_TX_PAUSE_OFF_INT_BIT BIT(26)
++#define GMAC1_RX_OVERRUN_INT_BIT BIT(25)
++#define GMAC1_STATUS_CHANGE_INT_BIT BIT(24)
++#define GMAC0_RESERVED_INT_BIT BIT(23)
++#define GMAC0_MIB_INT_BIT BIT(22)
++#define GMAC0_RX_PAUSE_ON_INT_BIT BIT(21)
++#define GMAC0_TX_PAUSE_ON_INT_BIT BIT(20)
++#define GMAC0_RX_PAUSE_OFF_INT_BIT BIT(19)
++#define GMAC0_TX_PAUSE_OFF_INT_BIT BIT(18)
++#define GMAC0_RX_OVERRUN_INT_BIT BIT(17)
++#define GMAC0_STATUS_CHANGE_INT_BIT BIT(16)
++#define CLASS_RX_FULL_INT_BIT(x) BIT(x + 2)
++#define HWFQ_EMPTY_INT_BIT BIT(1)
++#define SWFQ_EMPTY_INT_BIT BIT(0)
++
++#define GMAC0_INT_BITS (GMAC0_RESERVED_INT_BIT | GMAC0_MIB_INT_BIT | \
++ GMAC0_RX_PAUSE_ON_INT_BIT | \
++ GMAC0_TX_PAUSE_ON_INT_BIT | \
++ GMAC0_RX_PAUSE_OFF_INT_BIT | \
++ GMAC0_TX_PAUSE_OFF_INT_BIT | \
++ GMAC0_RX_OVERRUN_INT_BIT | \
++ GMAC0_STATUS_CHANGE_INT_BIT)
++#define GMAC1_INT_BITS (GMAC1_RESERVED_INT_BIT | GMAC1_MIB_INT_BIT | \
++ GMAC1_RX_PAUSE_ON_INT_BIT | \
++ GMAC1_TX_PAUSE_ON_INT_BIT | \
++ GMAC1_RX_PAUSE_OFF_INT_BIT | \
++ GMAC1_TX_PAUSE_OFF_INT_BIT | \
++ GMAC1_RX_OVERRUN_INT_BIT | \
++ GMAC1_STATUS_CHANGE_INT_BIT)
++
++#define CLASS_RX_FULL_INT_BITS 0xfffc
++
++/* GLOBAL_QUEUE_THRESHOLD_REG (offset 0x0070) */
++union queue_threshold {
++ unsigned int bits32;
++ struct bit_0070_2 {
++ /* 7:0 Software Free Queue Empty Threshold */
++ unsigned int swfq_empty:8;
++ /* 15:8 Hardware Free Queue Empty Threshold */
++ unsigned int hwfq_empty:8;
++ /* 23:16 */
++ unsigned int intrq:8;
++ /* 31:24 */
++ unsigned int toe_class:8;
++ } bits;
++};
++
++/* GMAC DMA Control Register
++ * GMAC0 offset 0x8000
++ * GMAC1 offset 0xC000
++ */
++union gmac_dma_ctrl {
++ unsigned int bits32;
++ struct bit_8000 {
++ /* bit 1:0 Peripheral Bus Width */
++ unsigned int td_bus:2;
++ /* bit 3:2 TxDMA max burst size for every AHB request */
++ unsigned int td_burst_size:2;
++ /* bit 7:4 TxDMA protection control */
++ unsigned int td_prot:4;
++ /* bit 9:8 Peripheral Bus Width */
++ unsigned int rd_bus:2;
++ /* bit 11:10 DMA max burst size for every AHB request */
++ unsigned int rd_burst_size:2;
++ /* bit 15:12 DMA Protection Control */
++ unsigned int rd_prot:4;
++ /* bit 17:16 */
++ unsigned int rd_insert_bytes:2;
++ /* bit 27:18 */
++ unsigned int reserved:10;
++ /* bit 28 1: Drop, 0: Accept */
++ unsigned int drop_small_ack:1;
++ /* bit 29 Loopback TxDMA to RxDMA */
++ unsigned int loopback:1;
++ /* bit 30 Tx DMA Enable */
++ unsigned int td_enable:1;
++ /* bit 31 Rx DMA Enable */
++ unsigned int rd_enable:1;
++ } bits;
++};
++
++/* GMAC Tx Weighting Control Register 0
++ * GMAC0 offset 0x8004
++ * GMAC1 offset 0xC004
++ */
++union gmac_tx_wcr0 {
++ unsigned int bits32;
++ struct bit_8004 {
++ /* bit 5:0 HW TX Queue 3 */
++ unsigned int hw_tq0:6;
++ /* bit 11:6 HW TX Queue 2 */
++ unsigned int hw_tq1:6;
++ /* bit 17:12 HW TX Queue 1 */
++ unsigned int hw_tq2:6;
++ /* bit 23:18 HW TX Queue 0 */
++ unsigned int hw_tq3:6;
++ /* bit 31:24 */
++ unsigned int reserved:8;
++ } bits;
++};
++
++/* GMAC Tx Weighting Control Register 1
++ * GMAC0 offset 0x8008
++ * GMAC1 offset 0xC008
++ */
++union gmac_tx_wcr1 {
++ unsigned int bits32;
++ struct bit_8008 {
++ /* bit 4:0 SW TX Queue 0 */
++ unsigned int sw_tq0:5;
++ /* bit 9:5 SW TX Queue 1 */
++ unsigned int sw_tq1:5;
++ /* bit 14:10 SW TX Queue 2 */
++ unsigned int sw_tq2:5;
++ /* bit 19:15 SW TX Queue 3 */
++ unsigned int sw_tq3:5;
++ /* bit 24:20 SW TX Queue 4 */
++ unsigned int sw_tq4:5;
++ /* bit 29:25 SW TX Queue 5 */
++ unsigned int sw_tq5:5;
++ /* bit 31:30 */
++ unsigned int reserved:2;
++ } bits;
++};
++
++/* GMAC DMA Tx Description Word 0 Register
++ * GMAC0 offset 0x8040
++ * GMAC1 offset 0xC040
++ */
++union gmac_txdesc_0 {
++ unsigned int bits32;
++ struct bit_8040 {
++ /* bit 15:0 Transfer size */
++ unsigned int buffer_size:16;
++ /* bit 21:16 number of descriptors used for the current frame */
++ unsigned int desc_count:6;
++ /* bit 22 Tx Status, 1: Successful 0: Failed */
++ unsigned int status_tx_ok:1;
++ /* bit 28:23 Tx Status, Reserved bits */
++ unsigned int status_rvd:6;
++ /* bit 29 protocol error during processing this descriptor */
++ unsigned int perr:1;
++ /* bit 30 data error during processing this descriptor */
++ unsigned int derr:1;
++ /* bit 31 */
++ unsigned int reserved:1;
++ } bits;
++};
++
++/* GMAC DMA Tx Description Word 1 Register
++ * GMAC0 offset 0x8044
++ * GMAC1 offset 0xC044
++ */
++union gmac_txdesc_1 {
++ unsigned int bits32;
++ struct txdesc_word1 {
++ /* bit 15: 0 Tx Frame Byte Count */
++ unsigned int byte_count:16;
++ /* bit 16 TSS segmentation use MTU setting */
++ unsigned int mtu_enable:1;
++ /* bit 17 IPV4 Header Checksum Enable */
++ unsigned int ip_chksum:1;
++ /* bit 18 IPV6 Tx Enable */
++ unsigned int ipv6_enable:1;
++ /* bit 19 TCP Checksum Enable */
++ unsigned int tcp_chksum:1;
++ /* bit 20 UDP Checksum Enable */
++ unsigned int udp_chksum:1;
++ /* bit 21 Bypass HW offload engine */
++ unsigned int bypass_tss:1;
++ /* bit 22 Don't update IP length field */
++ unsigned int ip_fixed_len:1;
++ /* bit 31:23 Tx Flag, Reserved */
++ unsigned int reserved:9;
++ } bits;
++};
++
++#define TSS_IP_FIXED_LEN_BIT BIT(22)
++#define TSS_BYPASS_BIT BIT(21)
++#define TSS_UDP_CHKSUM_BIT BIT(20)
++#define TSS_TCP_CHKSUM_BIT BIT(19)
++#define TSS_IPV6_ENABLE_BIT BIT(18)
++#define TSS_IP_CHKSUM_BIT BIT(17)
++#define TSS_MTU_ENABLE_BIT BIT(16)
++
++#define TSS_CHECKUM_ENABLE \
++ (TSS_IP_CHKSUM_BIT | TSS_IPV6_ENABLE_BIT | \
++ TSS_TCP_CHKSUM_BIT | TSS_UDP_CHKSUM_BIT)
++
++/* GMAC DMA Tx Description Word 2 Register
++ * GMAC0 offset 0x8048
++ * GMAC1 offset 0xC048
++ */
++union gmac_txdesc_2 {
++ unsigned int bits32;
++ unsigned int buf_adr;
++};
++
++/* GMAC DMA Tx Description Word 3 Register
++ * GMAC0 offset 0x804C
++ * GMAC1 offset 0xC04C
++ */
++union gmac_txdesc_3 {
++ unsigned int bits32;
++ struct txdesc_word3 {
++ /* bit 12: 0 Tx Frame Byte Count */
++ unsigned int mtu_size:13;
++ /* bit 28:13 */
++ unsigned int reserved:16;
++ /* bit 29 End of frame interrupt enable */
++ unsigned int eofie:1;
++ /* bit 31:30 11: only one, 10: first, 01: last, 00: linking */
++ unsigned int sof_eof:2;
++ } bits;
++};
++
++#define SOF_EOF_BIT_MASK 0x3fffffff
++#define SOF_BIT 0x80000000
++#define EOF_BIT 0x40000000
++#define EOFIE_BIT BIT(29)
++#define MTU_SIZE_BIT_MASK 0x1fff
++
++/* GMAC Tx Descriptor */
++struct gmac_txdesc {
++ union gmac_txdesc_0 word0;
++ union gmac_txdesc_1 word1;
++ union gmac_txdesc_2 word2;
++ union gmac_txdesc_3 word3;
++};
++
++/* GMAC DMA Rx Description Word 0 Register
++ * GMAC0 offset 0x8060
++ * GMAC1 offset 0xC060
++ */
++union gmac_rxdesc_0 {
++ unsigned int bits32;
++ struct bit_8060 {
++ /* bit 15:0 number of descriptors used for the current frame */
++ unsigned int buffer_size:16;
++ /* bit 21:16 number of descriptors used for the current frame */
++ unsigned int desc_count:6;
++ /* bit 24:22 Status of rx frame */
++ unsigned int status:4;
++ /* bit 28:26 Check Sum Status */
++ unsigned int chksum_status:3;
++ /* bit 29 protocol error during processing this descriptor */
++ unsigned int perr:1;
++ /* bit 30 data error during processing this descriptor */
++ unsigned int derr:1;
++ /* bit 31 TOE/CIS Queue Full dropped packet to default queue */
++ unsigned int drop:1;
++ } bits;
++};
++
++#define GMAC_RXDESC_0_T_derr BIT(30)
++#define GMAC_RXDESC_0_T_perr BIT(29)
++#define GMAC_RXDESC_0_T_chksum_status(x) BIT(x + 26)
++#define GMAC_RXDESC_0_T_status(x) BIT(x + 22)
++#define GMAC_RXDESC_0_T_desc_count(x) BIT(x + 16)
++
++#define RX_CHKSUM_IP_UDP_TCP_OK 0
++#define RX_CHKSUM_IP_OK_ONLY 1
++#define RX_CHKSUM_NONE 2
++#define RX_CHKSUM_IP_ERR_UNKNOWN 4
++#define RX_CHKSUM_IP_ERR 5
++#define RX_CHKSUM_TCP_UDP_ERR 6
++#define RX_CHKSUM_NUM 8
++
++#define RX_STATUS_GOOD_FRAME 0
++#define RX_STATUS_TOO_LONG_GOOD_CRC 1
++#define RX_STATUS_RUNT_FRAME 2
++#define RX_STATUS_SFD_NOT_FOUND 3
++#define RX_STATUS_CRC_ERROR 4
++#define RX_STATUS_TOO_LONG_BAD_CRC 5
++#define RX_STATUS_ALIGNMENT_ERROR 6
++#define RX_STATUS_TOO_LONG_BAD_ALIGN 7
++#define RX_STATUS_RX_ERR 8
++#define RX_STATUS_DA_FILTERED 9
++#define RX_STATUS_BUFFER_FULL 10
++#define RX_STATUS_NUM 16
++
++#define RX_ERROR_LENGTH(s) \
++ ((s) == RX_STATUS_TOO_LONG_GOOD_CRC || \
++ (s) == RX_STATUS_TOO_LONG_BAD_CRC || \
++ (s) == RX_STATUS_TOO_LONG_BAD_ALIGN)
++#define RX_ERROR_OVER(s) \
++ ((s) == RX_STATUS_BUFFER_FULL)
++#define RX_ERROR_CRC(s) \
++ ((s) == RX_STATUS_CRC_ERROR || \
++ (s) == RX_STATUS_TOO_LONG_BAD_CRC)
++#define RX_ERROR_FRAME(s) \
++ ((s) == RX_STATUS_ALIGNMENT_ERROR || \
++ (s) == RX_STATUS_TOO_LONG_BAD_ALIGN)
++#define RX_ERROR_FIFO(s) \
++ (0)
++
++/* GMAC DMA Rx Description Word 1 Register
++ * GMAC0 offset 0x8064
++ * GMAC1 offset 0xC064
++ */
++union gmac_rxdesc_1 {
++ unsigned int bits32;
++ struct rxdesc_word1 {
++ /* bit 15: 0 Rx Frame Byte Count */
++ unsigned int byte_count:16;
++ /* bit 31:16 Software ID */
++ unsigned int sw_id:16;
++ } bits;
++};
++
++/* GMAC DMA Rx Description Word 2 Register
++ * GMAC0 offset 0x8068
++ * GMAC1 offset 0xC068
++ */
++union gmac_rxdesc_2 {
++ unsigned int bits32;
++ unsigned int buf_adr;
++};
++
++#define RX_INSERT_NONE 0
++#define RX_INSERT_1_BYTE 1
++#define RX_INSERT_2_BYTE 2
++#define RX_INSERT_3_BYTE 3
++
++/* GMAC DMA Rx Description Word 3 Register
++ * GMAC0 offset 0x806C
++ * GMAC1 offset 0xC06C
++ */
++union gmac_rxdesc_3 {
++ unsigned int bits32;
++ struct rxdesc_word3 {
++ /* bit 7: 0 L3 data offset */
++ unsigned int l3_offset:8;
++ /* bit 15: 8 L4 data offset */
++ unsigned int l4_offset:8;
++ /* bit 23: 16 L7 data offset */
++ unsigned int l7_offset:8;
++ /* bit 24 Duplicated ACK detected */
++ unsigned int dup_ack:1;
++ /* bit 25 abnormal case found */
++ unsigned int abnormal:1;
++ /* bit 26 IPV4 option or IPV6 extension header */
++ unsigned int option:1;
++ /* bit 27 Out of Sequence packet */
++ unsigned int out_of_seq:1;
++ /* bit 28 Control Flag is present */
++ unsigned int ctrl_flag:1;
++ /* bit 29 End of frame interrupt enable */
++ unsigned int eofie:1;
++ /* bit 31:30 11: only one, 10: first, 01: last, 00: linking */
++ unsigned int sof_eof:2;
++ } bits;
++};
++
++/* GMAC Rx Descriptor, this is simply fitted over the queue registers */
++struct gmac_rxdesc {
++ union gmac_rxdesc_0 word0;
++ union gmac_rxdesc_1 word1;
++ union gmac_rxdesc_2 word2;
++ union gmac_rxdesc_3 word3;
++};
++
++/* GMAC Matching Rule Control Register 0
++ * GMAC0 offset 0x8078
++ * GMAC1 offset 0xC078
++ */
++#define MR_L2_BIT BIT(31)
++#define MR_L3_BIT BIT(30)
++#define MR_L4_BIT BIT(29)
++#define MR_L7_BIT BIT(28)
++#define MR_PORT_BIT BIT(27)
++#define MR_PRIORITY_BIT BIT(26)
++#define MR_DA_BIT BIT(23)
++#define MR_SA_BIT BIT(22)
++#define MR_ETHER_TYPE_BIT BIT(21)
++#define MR_VLAN_BIT BIT(20)
++#define MR_PPPOE_BIT BIT(19)
++#define MR_IP_VER_BIT BIT(15)
++#define MR_IP_HDR_LEN_BIT BIT(14)
++#define MR_FLOW_LABLE_BIT BIT(13)
++#define MR_TOS_TRAFFIC_BIT BIT(12)
++#define MR_SPR_BIT(x) BIT(x)
++#define MR_SPR_BITS 0xff
++
++/* GMAC_AHB_WEIGHT registers
++ * GMAC0 offset 0x80C8
++ * GMAC1 offset 0xC0C8
++ */
++union gmac_ahb_weight {
++ unsigned int bits32;
++ struct bit_80C8 {
++ /* 4:0 */
++ unsigned int hash_weight:5;
++ /* 9:5 */
++ unsigned int rx_weight:5;
++ /* 14:10 */
++ unsigned int tx_weight:5;
++ /* 19:15 Rx Data Pre Request FIFO Threshold */
++ unsigned int pre_req:5;
++ /* 24:20 DMA TqCtrl to Start tqDV FIFO Threshold */
++ unsigned int tq_dv_threshold:5;
++ /* 31:25 */
++ unsigned int reserved:7;
++ } bits;
++};
++
++/* GMAC RX FLTR
++ * GMAC0 Offset 0xA00C
++ * GMAC1 Offset 0xE00C
++ */
++union gmac_rx_fltr {
++ unsigned int bits32;
++ struct bit1_000c {
++ /* Enable receive of unicast frames that are sent to STA
++ * address
++ */
++ unsigned int unicast:1;
++ /* Enable receive of multicast frames that pass multicast
++ * filter
++ */
++ unsigned int multicast:1;
++ /* Enable receive of broadcast frames */
++ unsigned int broadcast:1;
++ /* Enable receive of all frames */
++ unsigned int promiscuous:1;
++ /* Enable receive of all error frames */
++ unsigned int error:1;
++ unsigned int reserved:27;
++ } bits;
++};
++
++/* GMAC Configuration 0
++ * GMAC0 Offset 0xA018
++ * GMAC1 Offset 0xE018
++ */
++union gmac_config0 {
++ unsigned int bits32;
++ struct bit1_0018 {
++ /* 0: disable transmit */
++ unsigned int dis_tx:1;
++ /* 1: disable receive */
++ unsigned int dis_rx:1;
++ /* 2: transmit data loopback enable */
++ unsigned int loop_back:1;
++ /* 3: flow control also trigged by Rx queues */
++ unsigned int flow_ctrl:1;
++ /* 4-7: adjust IFG from 96+/-56 */
++ unsigned int adj_ifg:4;
++ /* 8-10 maximum receive frame length allowed */
++ unsigned int max_len:3;
++ /* 11: disable back-off function */
++ unsigned int dis_bkoff:1;
++ /* 12: disable 16 collisions abort function */
++ unsigned int dis_col:1;
++ /* 13: speed up timers in simulation */
++ unsigned int sim_test:1;
++ /* 14: RX flow control enable */
++ unsigned int rx_fc_en:1;
++ /* 15: TX flow control enable */
++ unsigned int tx_fc_en:1;
++ /* 16: RGMII in-band status enable */
++ unsigned int rgmii_en:1;
++ /* 17: IPv4 RX Checksum enable */
++ unsigned int ipv4_rx_chksum:1;
++ /* 18: IPv6 RX Checksum enable */
++ unsigned int ipv6_rx_chksum:1;
++ /* 19: Remove Rx VLAN tag */
++ unsigned int rx_tag_remove:1;
++ /* 20 */
++ unsigned int rgmm_edge:1;
++ /* 21 */
++ unsigned int rxc_inv:1;
++ /* 22 */
++ unsigned int ipv6_exthdr_order:1;
++ /* 23 */
++ unsigned int rx_err_detect:1;
++ /* 24 */
++ unsigned int port0_chk_hwq:1;
++ /* 25 */
++ unsigned int port1_chk_hwq:1;
++ /* 26 */
++ unsigned int port0_chk_toeq:1;
++ /* 27 */
++ unsigned int port1_chk_toeq:1;
++ /* 28 */
++ unsigned int port0_chk_classq:1;
++ /* 29 */
++ unsigned int port1_chk_classq:1;
++ /* 30, 31 */
++ unsigned int reserved:2;
++ } bits;
++};
++
++#define CONFIG0_TX_RX_DISABLE (BIT(1) | BIT(0))
++#define CONFIG0_RX_CHKSUM (BIT(18) | BIT(17))
++#define CONFIG0_FLOW_RX BIT(14)
++#define CONFIG0_FLOW_TX BIT(15)
++#define CONFIG0_FLOW_TX_RX (BIT(14) | BIT(15))
++#define CONFIG0_FLOW_CTL (BIT(14) | BIT(15))
++
++#define CONFIG0_MAXLEN_SHIFT 8
++#define CONFIG0_MAXLEN_MASK (7 << CONFIG0_MAXLEN_SHIFT)
++#define CONFIG0_MAXLEN_1536 0
++#define CONFIG0_MAXLEN_1518 1
++#define CONFIG0_MAXLEN_1522 2
++#define CONFIG0_MAXLEN_1542 3
++#define CONFIG0_MAXLEN_9k 4 /* 9212 */
++#define CONFIG0_MAXLEN_10k 5 /* 10236 */
++#define CONFIG0_MAXLEN_1518__6 6
++#define CONFIG0_MAXLEN_1518__7 7
++
++/* GMAC Configuration 1
++ * GMAC0 Offset 0xA01C
++ * GMAC1 Offset 0xE01C
++ */
++union gmac_config1 {
++ unsigned int bits32;
++ struct bit1_001c {
++ /* Flow control set threshold */
++ unsigned int set_threshold:8;
++ /* Flow control release threshold */
++ unsigned int rel_threshold:8;
++ unsigned int reserved:16;
++ } bits;
++};
++
++#define GMAC_FLOWCTRL_SET_MAX 32
++#define GMAC_FLOWCTRL_SET_MIN 0
++#define GMAC_FLOWCTRL_RELEASE_MAX 32
++#define GMAC_FLOWCTRL_RELEASE_MIN 0
++
++/* GMAC Configuration 2
++ * GMAC0 Offset 0xA020
++ * GMAC1 Offset 0xE020
++ */
++union gmac_config2 {
++ unsigned int bits32;
++ struct bit1_0020 {
++ /* Flow control set threshold */
++ unsigned int set_threshold:16;
++ /* Flow control release threshold */
++ unsigned int rel_threshold:16;
++ } bits;
++};
++
++/* GMAC Configuration 3
++ * GMAC0 Offset 0xA024
++ * GMAC1 Offset 0xE024
++ */
++union gmac_config3 {
++ unsigned int bits32;
++ struct bit1_0024 {
++ /* Flow control set threshold */
++ unsigned int set_threshold:16;
++ /* Flow control release threshold */
++ unsigned int rel_threshold:16;
++ } bits;
++};
++
++/* GMAC STATUS
++ * GMAC0 Offset 0xA02C
++ * GMAC1 Offset 0xE02C
++ */
++union gmac_status {
++ unsigned int bits32;
++ struct bit1_002c {
++ /* Link status */
++ unsigned int link:1;
++ /* Link speed(00->2.5M 01->25M 10->125M) */
++ unsigned int speed:2;
++ /* Duplex mode */
++ unsigned int duplex:1;
++ unsigned int reserved_1:1;
++ /* PHY interface type */
++ unsigned int mii_rmii:2;
++ unsigned int reserved_2:25;
++ } bits;
++};
++
++#define GMAC_SPEED_10 0
++#define GMAC_SPEED_100 1
++#define GMAC_SPEED_1000 2
++
++#define GMAC_PHY_MII 0
++#define GMAC_PHY_GMII 1
++#define GMAC_PHY_RGMII_100_10 2
++#define GMAC_PHY_RGMII_1000 3
++
++/* Queue Header
++ * (1) TOE Queue Header
++ * (2) Non-TOE Queue Header
++ * (3) Interrupt Queue Header
++ *
++ * memory Layout
++ * TOE Queue Header
++ * 0x60003000 +---------------------------+ 0x0000
++ * | TOE Queue 0 Header |
++ * | 8 * 4 Bytes |
++ * +---------------------------+ 0x0020
++ * | TOE Queue 1 Header |
++ * | 8 * 4 Bytes |
++ * +---------------------------+ 0x0040
++ * | ...... |
++ * | |
++ * +---------------------------+
++ *
++ * Non TOE Queue Header
++ * 0x60002000 +---------------------------+ 0x0000
++ * | Default Queue 0 Header |
++ * | 2 * 4 Bytes |
++ * +---------------------------+ 0x0008
++ * | Default Queue 1 Header |
++ * | 2 * 4 Bytes |
++ * +---------------------------+ 0x0010
++ * | Classification Queue 0 |
++ * | 2 * 4 Bytes |
++ * +---------------------------+
++ * | Classification Queue 1 |
++ * | 2 * 4 Bytes |
++ * +---------------------------+ (n * 8 + 0x10)
++ * | ... |
++ * | 2 * 4 Bytes |
++ * +---------------------------+ (13 * 8 + 0x10)
++ * | Classification Queue 13 |
++ * | 2 * 4 Bytes |
++ * +---------------------------+ 0x80
++ * | Interrupt Queue 0 |
++ * | 2 * 4 Bytes |
++ * +---------------------------+
++ * | Interrupt Queue 1 |
++ * | 2 * 4 Bytes |
++ * +---------------------------+
++ * | Interrupt Queue 2 |
++ * | 2 * 4 Bytes |
++ * +---------------------------+
++ * | Interrupt Queue 3 |
++ * | 2 * 4 Bytes |
++ * +---------------------------+
++ *
++ */
++#define TOE_QUEUE_HDR_ADDR(n) (TOE_TOE_QUE_HDR_BASE + n * 32)
++#define TOE_Q_HDR_AREA_END (TOE_QUEUE_HDR_ADDR(TOE_TOE_QUEUE_MAX + 1))
++#define TOE_DEFAULT_Q_HDR_BASE(x) (TOE_NONTOE_QUE_HDR_BASE + 0x08 * (x))
++#define TOE_CLASS_Q_HDR_BASE (TOE_NONTOE_QUE_HDR_BASE + 0x10)
++#define TOE_INTR_Q_HDR_BASE (TOE_NONTOE_QUE_HDR_BASE + 0x80)
++#define INTERRUPT_QUEUE_HDR_ADDR(n) (TOE_INTR_Q_HDR_BASE + n * 8)
++#define NONTOE_Q_HDR_AREA_END (INTERRUPT_QUEUE_HDR_ADDR(TOE_INTR_QUEUE_MAX + 1))
++
++/* NONTOE Queue Header Word 0 */
++union nontoe_qhdr0 {
++ unsigned int bits32;
++ unsigned int base_size;
++};
++
++#define NONTOE_QHDR0_BASE_MASK (~0x0f)
++
++/* NONTOE Queue Header Word 1 */
++union nontoe_qhdr1 {
++ unsigned int bits32;
++ struct bit_nonqhdr1 {
++ /* bit 15:0 */
++ unsigned int rptr:16;
++ /* bit 31:16 */
++ unsigned int wptr:16;
++ } bits;
++};
++
++/* Non-TOE Queue Header */
++struct nontoe_qhdr {
++ union nontoe_qhdr0 word0;
++ union nontoe_qhdr1 word1;
++};
++
++#endif /* _GEMINI_ETHERNET_H */
diff --git a/target/linux/gemini/patches-4.14/0023-ARM-dts-Add-ethernet-to-the-Gemini-SoC.patch b/target/linux/gemini/patches-4.14/0023-ARM-dts-Add-ethernet-to-the-Gemini-SoC.patch
new file mode 100644
index 0000000..0960f6b
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0023-ARM-dts-Add-ethernet-to-the-Gemini-SoC.patch
@@ -0,0 +1,74 @@
+From 860005c1a2f16aaa33458a7d80c9728b710ae292 Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Mon, 6 Nov 2017 00:05:28 +0100
+Subject: [PATCH 23/31] ARM: dts: Add ethernet to the Gemini SoC
+
+This adds the Gemini ethernet node to the Gemini SoC.
+
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+---
+ arch/arm/boot/dts/gemini.dtsi | 44 ++++++++++++++++++++++++++++++++++++++++++-
+ 1 file changed, 43 insertions(+), 1 deletion(-)
+
+--- a/arch/arm/boot/dts/gemini.dtsi
++++ b/arch/arm/boot/dts/gemini.dtsi
+@@ -114,9 +114,16 @@
+ };
+ };
+ gmii_default_pins: pinctrl-gmii {
++ /*
++ * Only activate GMAC0 by default since
++ * GMAC1 will overlap with 8 GPIO lines
++ * gpio2a, gpio2b. Overlay groups with
++ * "gmii_gmac0_grp", "gmii_gmac1_grp" for
++ * both ethernet interfaces.
++ */
+ mux {
+ function = "gmii";
+- groups = "gmiigrp";
++ groups = "gmii_gmac0_grp";
+ };
+ };
+ pci_default_pins: pinctrl-pci {
+@@ -316,6 +323,41 @@
+ };
+ };
+
++ ethernet at 60000000 {
++ compatible = "cortina,gemini-ethernet";
++ reg = <0x60000000 0x4000>, /* Global registers, queue */
++ <0x60004000 0x2000>, /* V-bit */
++ <0x60006000 0x2000>; /* A-bit */
++ pinctrl-names = "default";
++ pinctrl-0 = <&gmii_default_pins>;
++ status = "disabled";
++ #address-cells = <1>;
++ #size-cells = <1>;
++ ranges;
++
++ gmac0: ethernet-port at 0 {
++ compatible = "cortina,gemini-ethernet-port";
++ reg = <0x60008000 0x2000>, /* Port 0 DMA/TOE */
++ <0x6000a000 0x2000>; /* Port 0 GMAC */
++ interrupt-parent = <&intcon>;
++ interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
++ resets = <&syscon GEMINI_RESET_GMAC0>;
++ clocks = <&syscon GEMINI_CLK_GATE_GMAC0>;
++ clock-names = "PCLK";
++ };
++
++ gmac1: ethernet-port at 1 {
++ compatible = "cortina,gemini-ethernet-port";
++ reg = <0x6000c000 0x2000>, /* Port 1 DMA/TOE */
++ <0x6000e000 0x2000>; /* Port 1 GMAC */
++ interrupt-parent = <&intcon>;
++ interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
++ resets = <&syscon GEMINI_RESET_GMAC1>;
++ clocks = <&syscon GEMINI_CLK_GATE_GMAC1>;
++ clock-names = "PCLK";
++ };
++ };
++
+ ata at 63000000 {
+ compatible = "cortina,gemini-pata", "faraday,ftide010";
+ reg = <0x63000000 0x1000>;
diff --git a/target/linux/gemini/patches-4.14/0024-net-gemini-Depend-on-HAS_IOMEM.patch b/target/linux/gemini/patches-4.14/0024-net-gemini-Depend-on-HAS_IOMEM.patch
new file mode 100644
index 0000000..2b95a92
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0024-net-gemini-Depend-on-HAS_IOMEM.patch
@@ -0,0 +1,30 @@
+From e0a7c7762e3a81e908bcca4176139ea9755d0985 Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Sun, 21 Jan 2018 14:15:41 +0100
+Subject: [PATCH 24/31] net: gemini: Depend on HAS_IOMEM
+
+The zeroday builder notices that since Usermode Linux does not
+have IO memory, the build fails for them when selecting everything
+it can enable.
+
+As the driver is clearly using memory-mapped registers to access
+the network adapter, we add depends on HAS_IOMEM to solve this
+problem.
+
+Reported-by: kbuild test robot <fengguang.wu at intel.com>
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+Signed-off-by: David S. Miller <davem at davemloft.net>
+---
+ drivers/net/ethernet/cortina/Kconfig | 1 +
+ 1 file changed, 1 insertion(+)
+
+--- a/drivers/net/ethernet/cortina/Kconfig
++++ b/drivers/net/ethernet/cortina/Kconfig
+@@ -14,6 +14,7 @@ if NET_VENDOR_CORTINA
+ config GEMINI_ETHERNET
+ tristate "Gemini Gigabit Ethernet support"
+ depends on OF
++ depends on HAS_IOMEM
+ select PHYLIB
+ select CRC32
+ ---help---
diff --git a/target/linux/gemini/patches-4.14/0025-ARM-dts-Set-D-Link-DNS-313-SATA-to-muxmode-0.patch b/target/linux/gemini/patches-4.14/0025-ARM-dts-Set-D-Link-DNS-313-SATA-to-muxmode-0.patch
new file mode 100644
index 0000000..06609a7
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0025-ARM-dts-Set-D-Link-DNS-313-SATA-to-muxmode-0.patch
@@ -0,0 +1,36 @@
+From f30cc6acdeb834be1a6ae54d47c84b2f8012b83d Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Thu, 18 Jan 2018 14:36:21 +0100
+Subject: [PATCH 25/31] ARM: dts: Set D-Link DNS-313 SATA to muxmode 0
+
+This stops the driver from trying to probe the ATA slave
+interface. The vendor code enables the slave interface
+but the driver in the vendor tree does not make use of
+it.
+
+Setting it to muxmode 0 disables the slave interface:
+the hardware only has the master interface connected
+to the one harddrive slot anyways.
+
+Without this change booting takes excessive time, so it
+is very annoying to end users.
+
+Fixes: dd5c0561db75 ("ARM: dts: Add basic devicetree for D-Link DNS-313")
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+---
+ARM SoC folks: please apply this for fixes for v4.16.
+---
+ arch/arm/boot/dts/gemini-dlink-dns-313.dts | 2 +-
+ 1 file changed, 1 insertion(+), 1 deletion(-)
+
+--- a/arch/arm/boot/dts/gemini-dlink-dns-313.dts
++++ b/arch/arm/boot/dts/gemini-dlink-dns-313.dts
+@@ -219,7 +219,7 @@
+
+ sata: sata at 46000000 {
+ /* The ROM uses this muxmode */
+- cortina,gemini-ata-muxmode = <3>;
++ cortina,gemini-ata-muxmode = <0>;
+ cortina,gemini-enable-sata-bridge;
+ status = "okay";
+ };
diff --git a/target/linux/gemini/patches-4.14/0026-power-gemini-poweroff-Avoid-spurious-poweroff.patch b/target/linux/gemini/patches-4.14/0026-power-gemini-poweroff-Avoid-spurious-poweroff.patch
new file mode 100644
index 0000000..e97aeac
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0026-power-gemini-poweroff-Avoid-spurious-poweroff.patch
@@ -0,0 +1,80 @@
+From da443bc125265cae24a0e5f7d1c7bba196a9319f Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Thu, 22 Feb 2018 08:34:35 +0100
+Subject: [PATCH 26/31] power: gemini-poweroff: Avoid spurious poweroff
+
+On the D-Link DIR-685 we get spurious poweroff from
+infrared. Since that block (CIR) doesn't even have a
+driver this can be safely ignored, we can revisit this
+code once we have a device supporting CIR.
+
+On the D-Link DNS-313 we get spurious poweroff from
+the power button. This appears to be an initialization
+issue: we need to enable the block (start the state
+machine) before we clear any dangling IRQ.
+
+This patch fixes both issues.
+
+Fixes: f7a388d6cd1c ("power: reset: Add a driver for the Gemini poweroff")
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+---
+ChangeLog v1->v2:
+- Fix both issues and rename the patch.
+- Proper commit message with specifics.
+---
+ drivers/power/reset/gemini-poweroff.c | 30 +++++++++++++++++-------------
+ 1 file changed, 17 insertions(+), 13 deletions(-)
+
+--- a/drivers/power/reset/gemini-poweroff.c
++++ b/drivers/power/reset/gemini-poweroff.c
+@@ -47,8 +47,12 @@ static irqreturn_t gemini_powerbutton_in
+ val &= 0x70U;
+ switch (val) {
+ case GEMINI_STAT_CIR:
+- dev_info(gpw->dev, "infrared poweroff\n");
+- orderly_poweroff(true);
++ /*
++ * We do not yet have a driver for the infrared
++ * controller so it can cause spurious poweroff
++ * events. Ignore those for now.
++ */
++ dev_info(gpw->dev, "infrared poweroff - ignored\n");
+ break;
+ case GEMINI_STAT_RTC:
+ dev_info(gpw->dev, "RTC poweroff\n");
+@@ -116,7 +120,17 @@ static int gemini_poweroff_probe(struct
+ return -ENODEV;
+ }
+
+- /* Clear the power management IRQ */
++ /*
++ * Enable the power controller. This is crucial on Gemini
++ * systems: if this is not done, pressing the power button
++ * will result in unconditional poweroff without any warning.
++ * This makes the kernel handle the poweroff.
++ */
++ val = readl(gpw->base + GEMINI_PWC_CTRLREG);
++ val |= GEMINI_CTRL_ENABLE;
++ writel(val, gpw->base + GEMINI_PWC_CTRLREG);
++
++ /* Now that the state machine is active, clear the IRQ */
+ val = readl(gpw->base + GEMINI_PWC_CTRLREG);
+ val |= GEMINI_CTRL_IRQ_CLR;
+ writel(val, gpw->base + GEMINI_PWC_CTRLREG);
+@@ -129,16 +143,6 @@ static int gemini_poweroff_probe(struct
+ pm_power_off = gemini_poweroff;
+ gpw_poweroff = gpw;
+
+- /*
+- * Enable the power controller. This is crucial on Gemini
+- * systems: if this is not done, pressing the power button
+- * will result in unconditional poweroff without any warning.
+- * This makes the kernel handle the poweroff.
+- */
+- val = readl(gpw->base + GEMINI_PWC_CTRLREG);
+- val |= GEMINI_CTRL_ENABLE;
+- writel(val, gpw->base + GEMINI_PWC_CTRLREG);
+-
+ dev_info(dev, "Gemini poweroff driver registered\n");
+
+ return 0;
diff --git a/target/linux/gemini/patches-4.14/0027-usb-host-add-DT-bindings-for-faraday-fotg2.patch b/target/linux/gemini/patches-4.14/0027-usb-host-add-DT-bindings-for-faraday-fotg2.patch
new file mode 100644
index 0000000..e677c38
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0027-usb-host-add-DT-bindings-for-faraday-fotg2.patch
@@ -0,0 +1,65 @@
+From 3699f119ff8da021fe7a1759e98e38ca88fa6766 Mon Sep 17 00:00:00 2001
+From: Hans Ulli Kroll <ulli.kroll at googlemail.com>
+Date: Wed, 8 Feb 2017 21:00:09 +0100
+Subject: [PATCH 27/31] usb: host: add DT bindings for faraday fotg2
+
+This adds device tree bindings for the Faraday FOTG2
+dual-mode host controller.
+
+Cc: devicetree at vger.kernel.org
+Signed-off-by: Hans Ulli Kroll <ulli.kroll at googlemail.com>
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+---
+ChangeLog v1->v3:
+- Change compatible to "faraday,fotg210" as the name of the
+ hardware block.
+- Add an elaborate SoC-specific compatible string for the
+ Cortina Systems Gemini so that SoC-specific features can
+ be enabled.
+- Add cortina,gemini-mini-b to indicate a Gemini PHY with
+ a Mini-B adapter connected.
+- Indicated that the Gemini version can handle "wakeup-source".
+- Add optional IP block clock.
+---
+ .../devicetree/bindings/usb/faraday,fotg210.txt | 35 ++++++++++++++++++++++
+ 1 file changed, 35 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/usb/faraday,fotg210.txt
+
+--- /dev/null
++++ b/Documentation/devicetree/bindings/usb/faraday,fotg210.txt
+@@ -0,0 +1,35 @@
++Faraday FOTG Host controller
++
++This OTG-capable USB host controller is found in Cortina Systems
++Gemini and other SoC products.
++
++Required properties:
++- compatible: should be one of:
++ "faraday,fotg210"
++ "cortina,gemini-usb", "faraday,fotg210"
++- reg: should contain one register range i.e. start and length
++- interrupts: description of the interrupt line
++
++Optional properties:
++- clocks: should contain the IP block clock
++- clock-names: should be "PCLK" for the IP block clock
++
++Required properties for "cortina,gemini-usb" compatible:
++- syscon: a phandle to the system controller to access PHY registers
++
++Optional properties for "cortina,gemini-usb" compatible:
++- cortina,gemini-mini-b: boolean property that indicates that a Mini-B
++ OTH connector is in use
++- wakeup-source: see power/wakeup-source.txt
++
++Example for Gemini:
++
++usb at 68000000 {
++ compatible = "cortina,gemini-usb", "faraday,fotg210";
++ reg = <0x68000000 0x1000>;
++ interrupts = <10 IRQ_TYPE_LEVEL_HIGH>;
++ clocks = <&cc 12>;
++ clock-names = "PCLK";
++ syscon = <&syscon>;
++ wakeup-source;
++};
diff --git a/target/linux/gemini/patches-4.14/0028-usb-host-fotg2-add-device-tree-probing.patch b/target/linux/gemini/patches-4.14/0028-usb-host-fotg2-add-device-tree-probing.patch
new file mode 100644
index 0000000..862cb64
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0028-usb-host-fotg2-add-device-tree-probing.patch
@@ -0,0 +1,61 @@
+From 5662c553e89ac4179ec2a7a94a342ba3e5d78cf7 Mon Sep 17 00:00:00 2001
+From: Hans Ulli Kroll <ulli.kroll at googlemail.com>
+Date: Thu, 9 Feb 2017 15:20:49 +0100
+Subject: [PATCH 28/31] usb: host: fotg2: add device tree probing
+
+Add device tree probing to the fotg2 driver.
+
+Signed-off-by: Hans Ulli Kroll <ulli.kroll at googlemail.com>
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+---
+ChangeLog v2->v3:
+- Change compatible to "faraday,fotg210" simply.
+---
+ drivers/usb/host/fotg210-hcd.c | 19 +++++++++++++++++++
+ 1 file changed, 19 insertions(+)
+
+--- a/drivers/usb/host/fotg210-hcd.c
++++ b/drivers/usb/host/fotg210-hcd.c
+@@ -23,6 +23,7 @@
+ * Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+ #include <linux/module.h>
++#include <linux/of.h>
+ #include <linux/device.h>
+ #include <linux/dmapool.h>
+ #include <linux/kernel.h>
+@@ -5600,6 +5601,15 @@ static int fotg210_hcd_probe(struct plat
+ if (usb_disabled())
+ return -ENODEV;
+
++ /* Right now device-tree probed devices don't get dma_mask set.
++ * Since shared usb code relies on it, set it here for now.
++ * Once we have dma capability bindings this can go away.
++ */
++
++ retval = dma_coerce_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
++ if (retval)
++ goto fail_create_hcd;
++
+ pdev->dev.power.power_state = PMSG_ON;
+
+ res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+@@ -5676,9 +5686,18 @@ static int fotg210_hcd_remove(struct pla
+ return 0;
+ }
+
++#ifdef CONFIG_OF
++static const struct of_device_id fotg210_of_match[] = {
++ { .compatible = "faraday,fotg210" },
++ {},
++};
++MODULE_DEVICE_TABLE(of, fotg210_of_match);
++#endif
++
+ static struct platform_driver fotg210_hcd_driver = {
+ .driver = {
+ .name = "fotg210-hcd",
++ .of_match_table = of_match_ptr(fotg210_of_match),
+ },
+ .probe = fotg210_hcd_probe,
+ .remove = fotg210_hcd_remove,
diff --git a/target/linux/gemini/patches-4.14/0029-usb-host-fotg2-add-silicon-clock-handling.patch b/target/linux/gemini/patches-4.14/0029-usb-host-fotg2-add-silicon-clock-handling.patch
new file mode 100644
index 0000000..4a1faf9
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0029-usb-host-fotg2-add-silicon-clock-handling.patch
@@ -0,0 +1,99 @@
+From acd19633751f14607ccd76f9dfde5bde7935766c Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Fri, 21 Apr 2017 20:46:12 +0200
+Subject: [PATCH 29/31] usb: host: fotg2: add silicon clock handling
+
+When used in a system with software-controller silicon clocks,
+the FOTG210 needs to grab, prepare and enable the clock.
+This is needed on for example the Cortina Gemini, where the
+platform will by default gate off the clock unless the
+peripheral (in this case the USB driver) grabs and enables
+the clock.
+
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+---
+ drivers/usb/host/fotg210-hcd.c | 26 ++++++++++++++++++++++----
+ drivers/usb/host/fotg210.h | 3 +++
+ 2 files changed, 25 insertions(+), 4 deletions(-)
+
+--- a/drivers/usb/host/fotg210-hcd.c
++++ b/drivers/usb/host/fotg210-hcd.c
+@@ -45,6 +45,7 @@
+ #include <linux/uaccess.h>
+ #include <linux/platform_device.h>
+ #include <linux/io.h>
++#include <linux/clk.h>
+
+ #include <asm/byteorder.h>
+ #include <asm/irq.h>
+@@ -5635,7 +5636,7 @@ static int fotg210_hcd_probe(struct plat
+ hcd->regs = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(hcd->regs)) {
+ retval = PTR_ERR(hcd->regs);
+- goto failed;
++ goto failed_put_hcd;
+ }
+
+ hcd->rsrc_start = res->start;
+@@ -5645,22 +5646,35 @@ static int fotg210_hcd_probe(struct plat
+
+ fotg210->caps = hcd->regs;
+
++ /* It's OK not to supply this clock */
++ fotg210->pclk = clk_get(dev, "PCLK");
++ if (!IS_ERR(fotg210->pclk)) {
++ retval = clk_prepare_enable(fotg210->pclk);
++ if (retval) {
++ dev_err(dev, "failed to enable PCLK\n");
++ goto failed_dis_clk;
++ }
++ }
++
+ retval = fotg210_setup(hcd);
+ if (retval)
+- goto failed;
++ goto failed_dis_clk;
+
+ fotg210_init(fotg210);
+
+ retval = usb_add_hcd(hcd, irq, IRQF_SHARED);
+ if (retval) {
+ dev_err(dev, "failed to add hcd with err %d\n", retval);
+- goto failed;
++ goto failed_dis_clk;
+ }
+ device_wakeup_enable(hcd->self.controller);
+
+ return retval;
+
+-failed:
++failed_dis_clk:
++ if (!IS_ERR(fotg210->pclk))
++ clk_disable_unprepare(fotg210->pclk);
++failed_put_hcd:
+ usb_put_hcd(hcd);
+ fail_create_hcd:
+ dev_err(dev, "init %s fail, %d\n", dev_name(dev), retval);
+@@ -5676,6 +5690,10 @@ static int fotg210_hcd_remove(struct pla
+ {
+ struct device *dev = &pdev->dev;
+ struct usb_hcd *hcd = dev_get_drvdata(dev);
++ struct fotg210_hcd *fotg210 = hcd_to_fotg210(hcd);
++
++ if (!IS_ERR(fotg210->pclk))
++ clk_disable_unprepare(fotg210->pclk);
+
+ if (!hcd)
+ return 0;
+--- a/drivers/usb/host/fotg210.h
++++ b/drivers/usb/host/fotg210.h
+@@ -182,6 +182,9 @@ struct fotg210_hcd { /* one per contro
+ # define COUNT(x)
+ #endif
+
++ /* silicon clock */
++ struct clk *pclk;
++
+ /* debug files */
+ struct dentry *debug_dir;
+ };
diff --git a/target/linux/gemini/patches-4.14/0030-usb-host-fotg2-add-Gemini-specific-handling.patch b/target/linux/gemini/patches-4.14/0030-usb-host-fotg2-add-Gemini-specific-handling.patch
new file mode 100644
index 0000000..2e781e4
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0030-usb-host-fotg2-add-Gemini-specific-handling.patch
@@ -0,0 +1,131 @@
+From e8ede0f62b39a3d3b06ae3dc04a74680a1f0a64b Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Fri, 21 Apr 2017 22:19:00 +0200
+Subject: [PATCH 30/31] usb: host: fotg2: add Gemini-specific handling
+
+The Cortina Systems Gemini has bolted on a PHY inside the
+silicon that can be handled by six bits in a MISC register in
+the system controller.
+
+If we are running on Gemini, look up a syscon regmap through
+a phandle and enable VBUS and optionally the Mini-B connector.
+
+If the device is flagged as "wakeup-source" using the standard
+DT bindings, we also enable this in the global controller for
+respective port.
+
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+---
+ drivers/usb/host/Kconfig | 1 +
+ drivers/usb/host/fotg210-hcd.c | 76 ++++++++++++++++++++++++++++++++++++++++++
+ 2 files changed, 77 insertions(+)
+
+--- a/drivers/usb/host/Kconfig
++++ b/drivers/usb/host/Kconfig
+@@ -375,6 +375,7 @@ config USB_ISP1362_HCD
+ config USB_FOTG210_HCD
+ tristate "FOTG210 HCD support"
+ depends on USB && HAS_DMA && HAS_IOMEM
++ select MFD_SYSCON
+ ---help---
+ Faraday FOTG210 is an OTG controller which can be configured as
+ an USB2.0 host. It is designed to meet USB2.0 EHCI specification
+--- a/drivers/usb/host/fotg210-hcd.c
++++ b/drivers/usb/host/fotg210-hcd.c
+@@ -46,6 +46,10 @@
+ #include <linux/platform_device.h>
+ #include <linux/io.h>
+ #include <linux/clk.h>
++#include <linux/bitops.h>
++/* For Cortina Gemini */
++#include <linux/mfd/syscon.h>
++#include <linux/regmap.h>
+
+ #include <asm/byteorder.h>
+ #include <asm/irq.h>
+@@ -5583,6 +5587,72 @@ static void fotg210_init(struct fotg210_
+ iowrite32(value, &fotg210->regs->otgcsr);
+ }
+
++/*
++ * Gemini-specific initialization function, only executed on the
++ * Gemini SoC using the global misc control register.
++ */
++#define GEMINI_GLOBAL_MISC_CTRL 0x30
++#define GEMINI_MISC_USB0_WAKEUP BIT(14)
++#define GEMINI_MISC_USB1_WAKEUP BIT(15)
++#define GEMINI_MISC_USB0_VBUS_ON BIT(22)
++#define GEMINI_MISC_USB1_VBUS_ON BIT(23)
++#define GEMINI_MISC_USB0_MINI_B BIT(29)
++#define GEMINI_MISC_USB1_MINI_B BIT(30)
++
++static int fotg210_gemini_init(struct device *dev, struct usb_hcd *hcd)
++{
++ struct device_node *np = dev->of_node;
++ struct regmap *map;
++ bool mini_b;
++ bool wakeup;
++ u32 mask, val;
++ int ret;
++
++ map = syscon_regmap_lookup_by_phandle(np, "syscon");
++ if (IS_ERR(map)) {
++ dev_err(dev, "no syscon\n");
++ return PTR_ERR(map);
++ }
++ mini_b = of_property_read_bool(np, "cortina,gemini-mini-b");
++ wakeup = of_property_read_bool(np, "wakeup-source");
++
++ /*
++ * Figure out if this is USB0 or USB1 by simply checking the
++ * physical base address.
++ */
++ mask = 0;
++ if (hcd->rsrc_start == 0x69000000) {
++ val = GEMINI_MISC_USB1_VBUS_ON;
++ if (mini_b)
++ val |= GEMINI_MISC_USB1_MINI_B;
++ else
++ mask |= GEMINI_MISC_USB1_MINI_B;
++ if (wakeup)
++ val |= GEMINI_MISC_USB1_WAKEUP;
++ else
++ mask |= GEMINI_MISC_USB1_WAKEUP;
++ } else {
++ val = GEMINI_MISC_USB0_VBUS_ON;
++ if (mini_b)
++ val |= GEMINI_MISC_USB0_MINI_B;
++ else
++ mask |= GEMINI_MISC_USB0_MINI_B;
++ if (wakeup)
++ val |= GEMINI_MISC_USB0_WAKEUP;
++ else
++ mask |= GEMINI_MISC_USB0_WAKEUP;
++ }
++
++ ret = regmap_update_bits(map, GEMINI_GLOBAL_MISC_CTRL, mask, val);
++ if (ret) {
++ dev_err(dev, "failed to initialize Gemini PHY\n");
++ return ret;
++ }
++
++ dev_info(dev, "initialized Gemini PHY\n");
++ return 0;
++}
++
+ /**
+ * fotg210_hcd_probe - initialize faraday FOTG210 HCDs
+ *
+@@ -5662,6 +5732,12 @@ static int fotg210_hcd_probe(struct plat
+
+ fotg210_init(fotg210);
+
++ if (of_device_is_compatible(dev->of_node, "cortina,gemini-usb")) {
++ retval = fotg210_gemini_init(dev, hcd);
++ if (retval)
++ goto failed_dis_clk;
++ }
++
+ retval = usb_add_hcd(hcd, irq, IRQF_SHARED);
+ if (retval) {
+ dev_err(dev, "failed to add hcd with err %d\n", retval);
diff --git a/target/linux/gemini/patches-4.14/0031-ARM-dts-Add-the-FOTG210-USB-host-to-Gemini.patch b/target/linux/gemini/patches-4.14/0031-ARM-dts-Add-the-FOTG210-USB-host-to-Gemini.patch
new file mode 100644
index 0000000..cb6fdb8
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0031-ARM-dts-Add-the-FOTG210-USB-host-to-Gemini.patch
@@ -0,0 +1,178 @@
+From dd62aee5d2d24199e71e745544e49a1a8b3c6f7a Mon Sep 17 00:00:00 2001
+From: Linus Walleij <linus.walleij at linaro.org>
+Date: Fri, 21 Apr 2017 20:50:22 +0200
+Subject: [PATCH 31/31] ARM: dts: Add the FOTG210 USB host to Gemini
+
+This adds the FOTG210 USB host controller to the Gemini
+device trees. In the main SoC DTSI it is flagged as disabled
+and then it is selectively enabled on the devices that utilize
+it (these per-platform enablements are done on the out-of-tree
+OpenWrt patch set). It is not enabled on the Itian SquareOne
+NAS/router since this instead has a VIA host controller
+soldered on the PCI port, and can gate off these USB host
+controllers.
+
+Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
+---
+USB maintainers: I will merge this through the ARM SoC tree,
+the patch is only included in the series for context.
+---
+ arch/arm/boot/dts/gemini-dlink-dir-685.dts | 8 ++++++++
+ arch/arm/boot/dts/gemini-nas4220b.dts | 8 ++++++++
+ arch/arm/boot/dts/gemini-rut1xx.dts | 20 ++++++++++++++++++++
+ arch/arm/boot/dts/gemini-wbd111.dts | 20 ++++++++++++++++++++
+ arch/arm/boot/dts/gemini-wbd222.dts | 21 +++++++++++++++++++++
+ arch/arm/boot/dts/gemini.dtsi | 26 ++++++++++++++++++++++++++
+ 6 files changed, 103 insertions(+)
+
+--- a/arch/arm/boot/dts/gemini-dlink-dir-685.dts
++++ b/arch/arm/boot/dts/gemini-dlink-dir-685.dts
+@@ -303,5 +303,13 @@
+ };
+ };
+ };
++
++ usb at 68000000 {
++ status = "okay";
++ };
++
++ usb at 69000000 {
++ status = "okay";
++ };
+ };
+ };
+--- a/arch/arm/boot/dts/gemini-nas4220b.dts
++++ b/arch/arm/boot/dts/gemini-nas4220b.dts
+@@ -146,5 +146,13 @@
+ ata at 63000000 {
+ status = "okay";
+ };
++
++ usb at 68000000 {
++ status = "okay";
++ };
++
++ usb at 69000000 {
++ status = "okay";
++ };
+ };
+ };
+--- a/arch/arm/boot/dts/gemini-rut1xx.dts
++++ b/arch/arm/boot/dts/gemini-rut1xx.dts
+@@ -114,5 +114,25 @@
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio1_default_pins>;
+ };
++
++ ethernet at 60000000 {
++ status = "okay";
++
++ ethernet-port at 0 {
++ phy-mode = "rgmii";
++ phy-handle = <&phy0>;
++ };
++ ethernet-port at 1 {
++ /* Not used in this platform */
++ };
++ };
++
++ usb at 68000000 {
++ status = "okay";
++ };
++
++ usb at 69000000 {
++ status = "okay";
++ };
+ };
+ };
+--- a/arch/arm/boot/dts/gemini-wbd111.dts
++++ b/arch/arm/boot/dts/gemini-wbd111.dts
+@@ -160,5 +160,25 @@
+ <0x6000 0 0 3 &pci_intc 1>,
+ <0x6000 0 0 4 &pci_intc 2>;
+ };
++
++ ethernet at 60000000 {
++ status = "okay";
++
++ ethernet-port at 0 {
++ phy-mode = "rgmii";
++ phy-handle = <&phy0>;
++ };
++ ethernet-port at 1 {
++ /* Not used in this platform */
++ };
++ };
++
++ usb at 68000000 {
++ status = "okay";
++ };
++
++ usb at 69000000 {
++ status = "okay";
++ };
+ };
+ };
+--- a/arch/arm/boot/dts/gemini-wbd222.dts
++++ b/arch/arm/boot/dts/gemini-wbd222.dts
+@@ -165,5 +165,26 @@
+ <0x6000 0 0 3 &pci_intc 1>,
+ <0x6000 0 0 4 &pci_intc 2>;
+ };
++
++ ethernet at 60000000 {
++ status = "okay";
++
++ ethernet-port at 0 {
++ phy-mode = "rgmii";
++ phy-handle = <&phy0>;
++ };
++ ethernet-port at 1 {
++ phy-mode = "rgmii";
++ phy-handle = <&phy1>;
++ };
++ };
++
++ usb at 68000000 {
++ status = "okay";
++ };
++
++ usb at 69000000 {
++ status = "okay";
++ };
+ };
+ };
+--- a/arch/arm/boot/dts/gemini.dtsi
++++ b/arch/arm/boot/dts/gemini.dtsi
+@@ -411,5 +411,31 @@
+ #size-cells = <0>;
+ status = "disabled";
+ };
++
++ usb at 68000000 {
++ compatible = "cortina,gemini-usb", "faraday,fotg210";
++ reg = <0x68000000 0x1000>;
++ interrupts = <10 IRQ_TYPE_LEVEL_HIGH>;
++ resets = <&syscon GEMINI_RESET_USB0>;
++ clocks = <&syscon GEMINI_CLK_GATE_USB0>;
++ clock-names = "PCLK";
++ pinctrl-names = "default";
++ pinctrl-0 = <&usb_default_pins>;
++ syscon = <&syscon>;
++ status = "disabled";
++ };
++
++ usb at 69000000 {
++ compatible = "cortina,gemini-usb", "faraday,fotg210";
++ reg = <0x69000000 0x1000>;
++ interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
++ resets = <&syscon GEMINI_RESET_USB1>;
++ clocks = <&syscon GEMINI_CLK_GATE_USB1>;
++ clock-names = "PCLK";
++ pinctrl-names = "default";
++ pinctrl-0 = <&usb_default_pins>;
++ syscon = <&syscon>;
++ status = "disabled";
++ };
+ };
+ };
diff --git a/target/linux/gemini/patches-4.14/0032-usb-host-fotg2-restart-hcd-after-port-reset.patch b/target/linux/gemini/patches-4.14/0032-usb-host-fotg2-restart-hcd-after-port-reset.patch
new file mode 100644
index 0000000..1479644
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0032-usb-host-fotg2-restart-hcd-after-port-reset.patch
@@ -0,0 +1,31 @@
+From 731a2896e11b4e6a8d252e6c14edb1b09dbfcd46 Mon Sep 17 00:00:00 2001
+From: Hans Ulli Kroll <ulli.kroll at googlemail.com>
+Date: Sat, 14 Apr 2018 18:49:57 +0200
+Subject: [PATCH 1/2] usb: host: fotg2: restart hcd after port reset
+
+on Gemini SoC FOTG2 stalls after port reset
+rerstart the hcd.
+
+Signed-off-by: Hans Ulli Kroll <ulli.kroll at googlemail.com>
+---
+ drivers/usb/host/fotg210-hcd.c | 4 ++++
+ 1 file changed, 4 insertions(+)
+
+diff --git a/drivers/usb/host/fotg210-hcd.c b/drivers/usb/host/fotg210-hcd.c
+index 2acc51b0be5a..bc9efb49adc7 100644
+--- a/drivers/usb/host/fotg210-hcd.c
++++ b/drivers/usb/host/fotg210-hcd.c
+@@ -1658,6 +1658,10 @@ static int fotg210_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
+ /* see what we found out */
+ temp = check_reset_complete(fotg210, wIndex, status_reg,
+ fotg210_readl(fotg210, status_reg));
++
++ /* restart schedule */
++ fotg210->command |= CMD_RUN;
++ fotg210_writel(fotg210, fotg210->command, &fotg210->regs->command);
+ }
+
+ if (!(temp & (PORT_RESUME|PORT_RESET))) {
+--
+2.16.2
+
diff --git a/target/linux/gemini/patches-4.14/0900-arm-dts-gemini-add-openwrt-partitions-for-nas4220b.patch b/target/linux/gemini/patches-4.14/0900-arm-dts-gemini-add-openwrt-partitions-for-nas4220b.patch
new file mode 100644
index 0000000..0fae0af
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0900-arm-dts-gemini-add-openwrt-partitions-for-nas4220b.patch
@@ -0,0 +1,17 @@
+--- a/arch/arm/boot/dts/gemini-nas4220b.dts
++++ b/arch/arm/boot/dts/gemini-nas4220b.dts
+@@ -115,6 +115,14 @@
+ reg = <0x00fe0000 0x00020000>;
+ read-only;
+ };
++ firmware at 20000 {
++ label = "firmware";
++ reg = <0x00020000 0x00f00000>;
++ };
++ rootfs at 320000 {
++ label = "rootfs";
++ reg = <0x00320000 0x00c00000>;
++ };
+ };
+
+ syscon: syscon at 40000000 {
diff --git a/target/linux/gemini/patches-4.14/0901-arm-dts-gemini-fix-ethernet-for-nas4220b.patch b/target/linux/gemini/patches-4.14/0901-arm-dts-gemini-fix-ethernet-for-nas4220b.patch
new file mode 100644
index 0000000..90e95a7
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0901-arm-dts-gemini-fix-ethernet-for-nas4220b.patch
@@ -0,0 +1,69 @@
+--- a/arch/arm/boot/dts/gemini-nas4220b.dts
++++ b/arch/arm/boot/dts/gemini-nas4220b.dts
+@@ -137,6 +137,47 @@
+ groups = "gpio1dgrp";
+ };
+ };
++ pinctrl-gmii {
++ mux {
++ function = "gmii";
++ groups = "gmii_gmac0_grp";
++ };
++ conf0 {
++ pins = "V8 GMAC0 RXDV", "T10 GMAC1 RXDV";
++ skew-delay = <0>;
++ };
++ conf1 {
++ pins = "Y7 GMAC0 RXC", "Y11 GMAC1 RXC";
++ skew-delay = <15>;
++ };
++ conf2 {
++ pins = "T8 GMAC0 TXEN", "W11 GMAC1 TXEN";
++ skew-delay = <7>;
++ };
++ conf3 {
++ pins = "U8 GMAC0 TXC";
++ skew-delay = <11>;
++ };
++ conf4 {
++ pins = "V11 GMAC1 TXC";
++ skew-delay = <10>;
++ };
++ conf5 {
++ pins = "W8 GMAC0 RXD0", "V9 GMAC0 RXD1",
++ "Y8 GMAC0 RXD2", "U9 GMAC0 RXD3",
++ "T7 GMAC0 TXD0", "U6 GMAC0 TXD1",
++ "V7 GMAC0 TXD2", "U7 GMAC0 TXD3",
++ "Y12 GMAC1 RXD0", "V12 GMAC1 RXD1",
++ "T11 GMAC1 RXD2", "W12 GMAC1 RXD3",
++ "U10 GMAC1 TXD0", "Y10 GMAC1 TXD1",
++ "W10 GMAC1 TXD2", "T9 GMAC1 TXD3";
++ skew-delay = <7>;
++ };
++ conf6 {
++ groups = "gmii_gmac0_grp";
++ drive-strength = <16>;
++ };
++ };
+ };
+ };
+
+@@ -151,6 +192,18 @@
+ pinctrl-0 = <&gpio1_default_pins>;
+ };
+
++ ethernet at 60000000 {
++ status = "okay";
++
++ gmac0: ethernet-port at 0 {
++ phy-mode = "rgmii";
++ phy-handle = <&phy0>;
++ };
++ gmac1: ethernet-port at 1 {
++ status = "disabled";
++ };
++ };
++
+ ata at 63000000 {
+ status = "okay";
+ };
diff --git a/target/linux/gemini/patches-4.14/0902-arm-dts-gemini-add-second-ata-for-nas4220b.patch b/target/linux/gemini/patches-4.14/0902-arm-dts-gemini-add-second-ata-for-nas4220b.patch
new file mode 100644
index 0000000..ef98172
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0902-arm-dts-gemini-add-second-ata-for-nas4220b.patch
@@ -0,0 +1,13 @@
+--- a/arch/arm/boot/dts/gemini-nas4220b.dts
++++ b/arch/arm/boot/dts/gemini-nas4220b.dts
+@@ -208,6 +208,10 @@
+ status = "okay";
+ };
+
++ ata at 63400000 {
++ status = "okay";
++ };
++
+ usb at 68000000 {
+ status = "okay";
+ };
diff --git a/target/linux/gemini/patches-4.14/0903-arm-dts-gemini-disable-usb-port-1-until-fixed.patch b/target/linux/gemini/patches-4.14/0903-arm-dts-gemini-disable-usb-port-1-until-fixed.patch
new file mode 100644
index 0000000..6962d56
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0903-arm-dts-gemini-disable-usb-port-1-until-fixed.patch
@@ -0,0 +1,11 @@
+--- a/arch/arm/boot/dts/gemini-nas4220b.dts
++++ b/arch/arm/boot/dts/gemini-nas4220b.dts
+@@ -217,7 +217,7 @@
+ };
+
+ usb at 69000000 {
+- status = "okay";
++ status = "disabled";
+ };
+ };
+ };
diff --git a/target/linux/gemini/patches-4.14/0904-net-cortina-fix-uninitialized-struct-member-usage.patch b/target/linux/gemini/patches-4.14/0904-net-cortina-fix-uninitialized-struct-member-usage.patch
new file mode 100644
index 0000000..15a2d6c
--- /dev/null
+++ b/target/linux/gemini/patches-4.14/0904-net-cortina-fix-uninitialized-struct-member-usage.patch
@@ -0,0 +1,23 @@
+--- a/drivers/net/ethernet/cortina/gemini.c
++++ b/drivers/net/ethernet/cortina/gemini.c
+@@ -1013,9 +1013,9 @@ static int geth_resize_freeq(struct gemi
+ int ret;
+
+ if (netdev->dev_id == 0)
+- other_netdev = geth->port1->netdev;
++ other_netdev = (geth->port1)? geth->port1->netdev : NULL;
+ else
+- other_netdev = geth->port0->netdev;
++ other_netdev = (geth->port0)? geth->port0->netdev : NULL;
+
+ if (other_netdev && netif_running(other_netdev))
+ return -EBUSY;
+@@ -2510,6 +2510,8 @@ static int gemini_ethernet_probe(struct
+ if (IS_ERR(geth->base))
+ return PTR_ERR(geth->base);
+ geth->dev = dev;
++ geth->port0 = NULL;
++ geth->port1 = NULL;
+
+ /* Wait for ports to stabilize */
+ do {
More information about the lede-commits
mailing list