[openwrt/openwrt] ipq806x: add support for NEC Aterm WG2600HP

LEDE Commits lede-commits at lists.infradead.org
Tue Jun 19 22:44:17 PDT 2018


mkresin pushed a commit to openwrt/openwrt.git, branch master:
https://git.lede-project.org/4645a6d3183ad27ab1ca74ed82495ac8f6019331

commit 4645a6d3183ad27ab1ca74ed82495ac8f6019331
Author: INAGAKI Hiroshi <musashino.open at gmail.com>
AuthorDate: Thu May 17 16:06:02 2018 +0900

    ipq806x: add support for NEC Aterm WG2600HP
    
    NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
    IPQ8064.
    
    Specification:
    
    - IPQ8064 (384 - 1,400 MHz)
    - 512 MB of RAM
    - 32 MB of Flash (SPI)
    - 4T4R 2.4/5 GHz
    - 5x 10/100/1000 Mbps Ethernet
    - 12x LEDs, 4x keys
    - 1x USB 3.0 Type-A
    - UART header on PCB
      - RX, TX, NC, GND, Vcc from power connector side
      - baudrate: 115200 bps
    
    Flash instruction using initramfs image:
    1. Connect serial cable to UART header
    2. Connect power cable and turn on the router
    3. When the "Press the [f] key and hit [enter] to enter failsafe mode"
    message is displayed on the console, press the "f" key and Enter key
    sequentially to enter the failsafe mode
    4. create fw_env.config file with following contents on failsafe mode:
      /dev/mtd9 0x0 0x10000 0x10000
    5. Execute following commands to add and change the environment
    variables of U-Boot
      fw_setenv ipaddr "192.168.0.1"
      fw_setenv serverip "192.168.0.2"
      fw_setenv autostart "yes"
      fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin;
      bootipq"
    6. Set the IP address of the computer to 192.168.0.2, connect to the LAN
    port of WG2600HP, and start the TFTP server on the computer
    7. Rename OpenWrt initramfs image for WG2600HP to
    "wg2600hp-initramfs.bin" and place it in the TFTP directory
    8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP
    9. WG2600HP downloads initramfs image from TFTP server on the computer,
    loads it and boot with initramfs image
    10. On the initramfs image, execute "mtd erase firmware" to erase stock
    firmware and execute sysupgrade with the sysupgrade image
    11. Wait ~180 seconds to complete flashing
    
    Signed-off-by: INAGAKI Hiroshi <musashino.open at gmail.com>
---
 .../linux/ipq806x/base-files/etc/board.d/01_leds   |   5 +
 .../ipq806x/base-files/etc/board.d/02_network      |   4 +
 .../etc/hotplug.d/firmware/11-ath10k-caldata       |   2 +
 .../etc/hotplug.d/ieee80211/10_fix_wifi_mac        |   3 +
 .../ipq806x/base-files/lib/upgrade/platform.sh     |   1 +
 target/linux/ipq806x/config-4.14                   |   1 +
 .../arch/arm/boot/dts/qcom-ipq8064-wg2600hp.dts    | 448 +++++++++++++++++++++
 target/linux/ipq806x/image/Makefile                |  12 +
 .../patches-4.14/0069-arm-boot-add-dts-files.patch |  15 +-
 9 files changed, 484 insertions(+), 7 deletions(-)

diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds
index a8d9573faa..fea4d7c8bb 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds
@@ -15,6 +15,11 @@ compex,wpq864)
 	ucidef_set_led_usbport "usb" "USB" "wpq864:green:usb" "usb1-port1" "usb2-port1"
 	ucidef_set_led_usbport "pcie-usb" "PCIe USB" "wpq864:green:usb-pcie" "usb3-port1"
 	;;
+nec,wg2600hp)
+	ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:green:wlan2g" "phy1tpt"
+	ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:green:wlan5g" "phy0tpt"
+	ucidef_set_led_switch "wan" "WAN" "${boardname}:green:active" "switch0" "0x1e"
+	;;
 netgear,d7800 |\
 netgear,r7500 |\
 netgear,r7500v2 |\
diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network
index 9d8af44855..f5daf62653 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/02_network
+++ b/target/linux/ipq806x/base-files/etc/board.d/02_network
@@ -29,6 +29,10 @@ linksys,ea8500)
 	ucidef_set_interface_macaddr "lan" "$hw_mac_addr"
 	ucidef_set_interface_macaddr "wan" "$hw_mac_addr"
 	;;
+nec,wg2600hp)
+	ucidef_add_switch "switch0" \
+		"2:lan" "3:lan" "4:lan" "5:lan" "6 at eth1" "1:wan" "0 at eth0"
+	;;
 qcom,ipq8064-db149)
 	ucidef_set_interface_lan "eth1 eth2 eth3"
 	ucidef_add_switch "switch0" \
diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index ed99bd5ea8..fa49c250f0 100644
--- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -60,6 +60,7 @@ case "$FIRMWARE" in
 		ath10kcal_extract "radio" 4096 12064
 # 		ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_binary default-mac 8) -1)
 		;;
+	nec,wg2600hp |\
 	tplink,vr2600v)
 		ath10kcal_extract "ART" 4096 12064
 		;;
@@ -83,6 +84,7 @@ case "$FIRMWARE" in
 		ath10kcal_extract "radio" 20480 12064
 # 		ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_binary default-mac 8) -2)
 		;;
+	nec,wg2600hp |\
 	tplink,vr2600v)
 		ath10kcal_extract "ART" 20480 12064
 		;;
diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac b/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac
index 7e31c38561..afa425f075 100644
--- a/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac
+++ b/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac
@@ -15,6 +15,9 @@ case "$board" in
 	linksys,ea8500)
 		echo $(macaddr_add $(mtd_get_mac_ascii devinfo hw_mac_addr) $(($PHYNBR + 1)) ) > /sys${DEVPATH}/macaddress
 		;;
+	nec,wg2600hp)
+		echo $(macaddr_add $(mtd_get_mac_binary PRODUCTDATA 12) $((1 - $PHYNBR)) ) > /sys${DEVPATH}/macaddress
+		;;
 	netgear,d7800 |\
 	netgear,r7500v2 |\
 	netgear,r7800)
diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
index 4f230eac8a..b41bea1c29 100644
--- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
@@ -32,6 +32,7 @@ platform_do_upgrade() {
 		MTD_CONFIG_ARGS="-s 0x200000"
 		default_do_upgrade "$ARGV"
 		;;
+	nec,wg2600hp |\
 	*)
 		default_do_upgrade "$ARGV"
 		;;
diff --git a/target/linux/ipq806x/config-4.14 b/target/linux/ipq806x/config-4.14
index d64e40637e..fda8f52d2c 100644
--- a/target/linux/ipq806x/config-4.14
+++ b/target/linux/ipq806x/config-4.14
@@ -309,6 +309,7 @@ CONFIG_MTD_QCOM_SMEM_PARTS=y
 CONFIG_MTD_SPI_NOR=y
 CONFIG_MTD_SPLIT_FIRMWARE=y
 CONFIG_MTD_SPLIT_FIT_FW=y
+CONFIG_MTD_SPLIT_UIMAGE_FW=y
 CONFIG_MTD_UBI=y
 CONFIG_MTD_UBI_BEB_LIMIT=20
 CONFIG_MTD_UBI_BLOCK=y
diff --git a/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064-wg2600hp.dts b/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064-wg2600hp.dts
new file mode 100644
index 0000000000..b643014b45
--- /dev/null
+++ b/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064-wg2600hp.dts
@@ -0,0 +1,448 @@
+#include "qcom-ipq8064-v2.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "NEC Aterm WG2600HP";
+	compatible = "nec,wg2600hp", "qcom,ipq8064";
+
+	memory at 0 {
+		reg = <0x42000000 0x1e000000>;
+		device_type = "memory";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		rsvd at 41200000 {
+			reg = <0x41200000 0x300000>;
+			no-map;
+		};
+	};
+
+	aliases {
+		serial0 = &gsbi4_serial;
+		mdio-gpio0 = &mdio0;
+
+		led-boot = &power_green;
+		led-failsafe = &power_green;
+		led-running = &power_green;
+		led-upgrade = &power_green;
+	};
+
+	chosen {
+		linux,stdout-path = "serial0:115200n8";
+	};
+
+	soc {
+		pinmux at 800000 {
+			button_pins: button_pins {
+				mux {
+					pins = "gpio16", "gpio54", "gpio24", "gpio25";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			i2c4_pins: i2c4_pinmux {
+				mux {
+					pins = "gpio12", "gpio13";
+					function = "gsbi4";
+					drive-strength = <12>;
+					bias-disable;
+				};
+			};
+
+			led_pins: led_pins {
+				mux {
+					pins = "gpio6", "gpio7", "gpio8", "gpio9", "gpio14",
+						"gpio15", "gpio55", "gpio56", "gpio57", "gpio58",
+						"gpio64", "gpio65";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-down;
+				};
+			};
+
+			spi_pins: spi_pins {
+				mux {
+					pins = "gpio18", "gpio19", "gpio21";
+					function = "gsbi5";
+					bias-pull-down;
+				};
+
+				data {
+					pins = "gpio18", "gpio19";
+					drive-strength = <10>;
+				};
+
+				cs {
+					pins = "gpio20";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+
+				clk {
+					pins = "gpio21";
+					drive-strength = <12>;
+				};
+			};
+
+			mdio0_pins: mdio0_pins {
+				mux {
+					pins = "gpio0", "gpio1";
+					function = "gpio";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+
+			rgmii2_pins: rgmii2_pins {
+				mux {
+					pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+					       "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+					function = "rgmii2";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+
+			usb_pwr_en_pins: usb_pwr_en_pins {
+				mux {
+					pins = "gpio22";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-down;
+					output-high;
+				};
+			};
+		};
+
+		gsbi at 16300000 {
+			qcom,mode = <GSBI_PROT_I2C_UART>;
+			status = "ok";
+			serial at 16340000 {
+				status = "ok";
+			};
+			/*
+			 * The i2c device on gsbi4 should not be enabled.
+			 * On ipq806x designs gsbi4 i2c is meant for exclusive
+			 * RPM usage. Turning this on in kernel manifests as
+			 * i2c failure for the RPM.
+			 */
+		};
+
+		gsbi5: gsbi at 1a200000 {
+			qcom,mode = <GSBI_PROT_SPI>;
+			status = "ok";
+
+			spi4: spi at 1a280000 {
+				status = "ok";
+
+				pinctrl-0 = <&spi_pins>;
+				pinctrl-names = "default";
+
+				cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+				flash: m25p80 at 0 {
+					compatible = "jedec,spi-nor";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					spi-max-frequency = <50000000>;
+					reg = <0>;
+
+					SBL1 at 0 {
+						label = "SBL1";
+						reg = <0x0 0x20000>;
+						read-only;
+					};
+
+					MIBIB at 20000 {
+						label = "MIBIB";
+						reg = <0x20000 0x20000>;
+						read-only;
+					};
+
+					SBL2 at 40000 {
+						label = "SBL2";
+						reg = <0x40000 0x40000>;
+						read-only;
+					};
+
+					SBL3 at 80000 {
+						label = "SBL3";
+						reg = <0x80000 0x80000>;
+						read-only;
+					};
+
+					DDRCONFIG at 100000 {
+						label = "DDRCONFIG";
+						reg = <0x100000 0x10000>;
+						read-only;
+					};
+
+					SSD at 110000 {
+						label = "SSD";
+						reg = <0x110000 0x10000>;
+						read-only;
+					};
+
+					TZ at 120000 {
+						label = "TZ";
+						reg = <0x120000 0x80000>;
+						read-only;
+					};
+
+					RPM at 1a0000 {
+						label = "RPM";
+						reg = <0x1a0000 0x80000>;
+						read-only;
+					};
+
+					APPSBL at 220000 {
+						label = "APPSBL";
+						reg = <0x220000 0x80000>;
+						read-only;
+					};
+
+					APPSBLENV at 2a0000 {
+						label = "APPSBLENV";
+						reg = <0x2a0000 0x10000>;
+					};
+
+					PRODUCTDATA: PRODUCTDATA at 2b0000 {
+						label = "PRODUCTDATA";
+						reg = <0x2b0000 0x30000>;
+						read-only;
+					};
+
+					ART at 2e0000 {
+						label = "ART";
+						reg = <0x2e0000 0x40000>;
+						read-only;
+					};
+
+					TP at 320000 {
+						label = "TP";
+						reg = <0x320000 0x40000>;
+						read-only;
+					};
+
+					TINY at 360000 {
+						label = "TINY";
+						reg = <0x360000 0x500000>;
+						read-only;
+					};
+
+					firmware at 860000 {
+						label = "firmware";
+						reg = <0x860000 0x17a0000>;
+					};
+				};
+			};
+		};
+
+		phy at 100f8800 {		/* USB3 port 1 HS phy */
+			status = "ok";
+		};
+
+		phy at 100f8830 {		/* USB3 port 1 SS phy */
+			status = "ok";
+		};
+
+		phy at 110f8800 {		/* USB3 port 0 HS phy */
+			status = "ok";
+		};
+
+		phy at 110f8830 {		/* USB3 port 0 SS phy */
+			status = "ok";
+		};
+
+		usb30 at 0 {
+			status = "ok";
+
+			pinctrl-0 = <&usb_pwr_en_pins>;
+			pinctrl-names = "default";
+		};
+
+		usb30 at 1 {
+			status = "ok";
+		};
+
+		pcie0: pci at 1b500000 {
+			status = "ok";
+			reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_HIGH>;
+			pinctrl-0 = <&pcie0_pins>;
+			pinctrl-names = "default";
+		};
+
+		pcie1: pci at 1b700000 {
+			status = "ok";
+			reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_HIGH>;
+			pinctrl-0 = <&pcie1_pins>;
+			pinctrl-names = "default";
+			force_gen1 = <1>;
+		};
+
+		mdio0: mdio {
+			compatible = "virtual,mdio-gpio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
+			pinctrl-0 = <&mdio0_pins>;
+			pinctrl-names = "default";
+
+			phy0: ethernet-phy at 0 {
+				device_type = "ethernet-phy";
+				reg = <0>;
+				qca,ar8327-initvals = <
+					0x00004 0x7600000   /* PAD0_MODE */
+					0x00008 0x1000000   /* PAD5_MODE */
+					0x0000c 0x80        /* PAD6_MODE */
+					0x000e4 0x6a545     /* MAC_POWER_SEL */
+					0x000e0 0xc74164de  /* SGMII_CTRL */
+					0x0007c 0x4e        /* PORT0_STATUS */
+					0x00094 0x4e        /* PORT6_STATUS */
+					>;
+			};
+
+			phy4: ethernet-phy at 4 {
+				device_type = "ethernet-phy";
+				reg = <4>;
+			};
+		};
+
+		gmac1: ethernet at 37200000 {
+			status = "ok";
+			phy-mode = "rgmii";
+			qcom,id = <1>;
+
+			pinctrl-0 = <&rgmii2_pins>;
+			pinctrl-names = "default";
+
+			mtd-mac-address = <&PRODUCTDATA 6>;
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		gmac2: ethernet at 37400000 {
+			status = "ok";
+			phy-mode = "sgmii";
+			qcom,id = <2>;
+
+			mtd-mac-address = <&PRODUCTDATA 0>;
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&button_pins>;
+		pinctrl-names = "default";
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		bridge {
+			label = "bridge";
+			gpios = <&qcom_pinmux 24 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+			linux,input-type = <EV_SW>;
+		};
+
+		converter {
+			label = "converter";
+			gpios = <&qcom_pinmux 25 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+			linux,input-type = <EV_SW>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&led_pins>;
+		pinctrl-names = "default";
+
+		converter_green {
+			label = "wg2600hp:green:converter";
+			gpios = <&qcom_pinmux 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		power_red {
+			label = "wg2600hp:red:power";
+			gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		active_green {
+			label = "wg2600hp:green:active";
+			gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		active_red {
+			label = "wg2600hp:red:active";
+			gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		power_green: power_green {
+			label = "wg2600hp:green:power";
+			gpios = <&qcom_pinmux 14 GPIO_ACTIVE_HIGH>;
+		};
+
+		converter_red {
+			label = "wg2600hp:red:converter";
+			gpios = <&qcom_pinmux 15 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan2g_green {
+			label = "wg2600hp:green:wlan2g";
+			gpios = <&qcom_pinmux 55 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan2g_red {
+			label = "wg2600hp:red:wlan2g";
+			gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan5g_green {
+			label = "wg2600hp:green:wlan5g";
+			gpios = <&qcom_pinmux 57 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan5g_red {
+			label = "wg2600hp:red:wlan5g";
+			gpios = <&qcom_pinmux 58 GPIO_ACTIVE_HIGH>;
+		};
+
+		tv_green {
+			label = "wg2600hp:green:tv";
+			gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
+		};
+
+		tv_red {
+			label = "wg2600hp:red:tv";
+			gpios = <&qcom_pinmux 65 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&adm_dma {
+	status = "ok";
+};
diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile
index ac57991961..2902af3231 100644
--- a/target/linux/ipq806x/image/Makefile
+++ b/target/linux/ipq806x/image/Makefile
@@ -101,6 +101,18 @@ define Device/linksys_ea8500
 endef
 TARGET_DEVICES += linksys_ea8500
 
+define Device/nec_wg2600hp
+	$(call Device/LegacyImage)
+	DEVICE_DTS := qcom-ipq8064-wg2600hp
+	BLOCKSIZE := 64k
+	BOARD_NAME := wg2600hp
+	DEVICE_TITLE := NEC Aterm WG2600HP
+	IMAGES := sysupgrade.bin
+	IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
+	DEVICE_PACKAGES := ath10k-firmware-qca99x0
+endef
+TARGET_DEVICES += nec_wg2600hp
+
 define Device/netgear_d7800
 	$(call Device/DniImage)
 	DEVICE_DTS := qcom-ipq8064-d7800
diff --git a/target/linux/ipq806x/patches-4.14/0069-arm-boot-add-dts-files.patch b/target/linux/ipq806x/patches-4.14/0069-arm-boot-add-dts-files.patch
index fead994c00..59f37a7027 100644
--- a/target/linux/ipq806x/patches-4.14/0069-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq806x/patches-4.14/0069-arm-boot-add-dts-files.patch
@@ -10,19 +10,20 @@ Signed-off-by: John Crispin <john at phrozen.org>
 
 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -699,6 +699,15 @@ dtb-$(CONFIG_ARCH_QCOM) += \
- 	qcom-apq8084-mtp.dtb \
- 	qcom-ipq4019-ap.dk01.1-c1.dtb \
- 	qcom-ipq8064-ap148.dtb \
+@@ -699,6 +699,16 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+	qcom-apq8084-mtp.dtb \
+	qcom-ipq4019-ap.dk01.1-c1.dtb \
+	qcom-ipq8064-ap148.dtb \
 +	qcom-ipq8064-c2600.dtb \
 +	qcom-ipq8064-d7800.dtb \
 +	qcom-ipq8064-db149.dtb \
 +	qcom-ipq8064-ea8500.dtb \
 +	qcom-ipq8064-r7500.dtb \
 +	qcom-ipq8064-r7500v2.dtb \
++	qcom-ipq8064-wg2600hp.dtb \
 +	qcom-ipq8064-wpq864.dtb \
 +	qcom-ipq8065-nbg6817.dtb \
 +	qcom-ipq8065-r7800.dtb \
- 	qcom-msm8660-surf.dtb \
- 	qcom-msm8960-cdp.dtb \
- 	qcom-msm8974-lge-nexus5-hammerhead.dtb \
+	qcom-msm8660-surf.dtb \
+	qcom-msm8960-cdp.dtb \
+	qcom-msm8974-lge-nexus5-hammerhead.dtb \



More information about the lede-commits mailing list