[openwrt/openwrt] ar71xx: add support for WHQX E1700AC/E600G/E600GAC v2
LEDE Commits
lede-commits at lists.infradead.org
Thu Feb 22 15:22:46 PST 2018
pepe2k pushed a commit to openwrt/openwrt.git, branch master:
https://git.lede-project.org/d8e6c3f6d95304bc84269d2292581767fc9bfd3a
commit d8e6c3f6d95304bc84269d2292581767fc9bfd3a
Author: Peng Zhang <sd20 at qxwlan.com>
AuthorDate: Fri Jan 5 17:38:05 2018 +0800
ar71xx: add support for WHQX E1700AC/E600G/E600GAC v2
WHQX E1700AC v2 is based on Qualcomm QCA9563 + QCA9880 + QCA8334.
Specification:
- 750/400/250 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz (QCA9563) with external FEM (SKY85309-11)
- 3T3R 5 GHz (QCA9880) with external FEM (SKY85728-11)
- 2x 10/100/1000 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (USB 2.0 bus only)
- 1x microSIM slot
- 1x USB 2.0
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x 2-pos switch
- 1x DC jack for main power input (9-48 V)
- UART (J5) and LEDs (J13) headers on PCB
WHQX E600G is based on Qualcomm QCA9531.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 64/128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9531) with external PA (LXK-6601)
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses)
- 1x microSIM slot
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J100), SIM (J34), JTAG (J5) and LEDs (J7) headers on PCB
WHQX E600GAC is based on Qualcomm QCA9531 + QCA9887.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 64/128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887) with external FEM (SKY85703-11)
- 2x 10/100 Mbps Ethernet
- 6x LED (1x RGB, 5 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-12 V)
- UART (J100), USB (J102), JTAG (J5) and LEDs (J7) header on PCB
Important notice:
First version of these boards are using different mtd layout, with ART
data at the end. You should not use v2 images on v1 board because it
will result in lost of ART data!
Flash instruction (using U-Boot CLI and tftp server):
1. Configure PC with static IP 192.168.1.10 and tftp server.
2. Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
3. Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
4. Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
1. Configure PC with static IP 192.168.1.xxx(2-254)/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
3. Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Signed-off-by: Peng Zhang <sd20 at qxwlan.com>
[reworked: image generation code, mach-* files, commit description,
fixed minor code style issues, rebased on master]
Signed-off-by: Piotr Dymacz <pepe2k at gmail.com>
---
target/linux/ar71xx/base-files/etc/board.d/01_leds | 8 +-
.../linux/ar71xx/base-files/etc/board.d/02_network | 11 +-
target/linux/ar71xx/base-files/etc/diag.sh | 5 +
.../etc/hotplug.d/firmware/11-ath10k-caldata | 2 +
target/linux/ar71xx/base-files/lib/ar71xx.sh | 9 +
.../ar71xx/base-files/lib/upgrade/platform.sh | 3 +
target/linux/ar71xx/config-4.4 | 2 +
target/linux/ar71xx/config-4.9 | 2 +
.../ar71xx/files/arch/mips/ath79/Kconfig.openwrt | 22 +++
target/linux/ar71xx/files/arch/mips/ath79/Makefile | 2 +
.../ar71xx/files/arch/mips/ath79/mach-e1700ac-v2.c | 145 ++++++++++++++++
.../ar71xx/files/arch/mips/ath79/mach-e600g-v2.c | 184 +++++++++++++++++++++
.../linux/ar71xx/files/arch/mips/ath79/machtypes.h | 3 +
target/linux/ar71xx/generic/config-default | 2 +
target/linux/ar71xx/image/generic.mk | 59 +++++++
15 files changed, 453 insertions(+), 6 deletions(-)
diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds b/target/linux/ar71xx/base-files/etc/board.d/01_leds
index 6711fb4..725bab2 100755
--- a/target/linux/ar71xx/base-files/etc/board.d/01_leds
+++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds
@@ -64,7 +64,9 @@ ap90q|\
cpe505n|\
cpe830|\
cpe870|\
-dr531)
+dr531|\
+e600g-v2|\
+e600gac-v2)
ucidef_set_led_netdev "lan" "LAN" "$board:green:lan" "eth0"
ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth1"
@@ -342,6 +344,10 @@ dlan-pro-1200-ac)
ucidef_set_led_gpio "plcw" "dLAN" "devolo:status:dlan" "17" "0"
ucidef_set_led_gpio "plcr" "dLAN" "devolo:error:dlan" "16" "0"
;;
+e1700ac-v2)
+ ucidef_set_led_usbdev "usb" "USB" "$board:green:usb" "1-1"
+ ucidef_set_led_wlan "wlan2g" "WLAN2G" "$board:green:wlan2g" "phy1tpt"
+ ;;
esr900)
ucidef_set_led_wlan "wlan2g" "WLAN 2.4 GHz" "engenius:blue:wlan-2g" "phy0tpt"
ucidef_set_led_wlan "wlan5g" "WLAN 5 GHz" "engenius:blue:wlan-5g" "phy1tpt"
diff --git a/target/linux/ar71xx/base-files/etc/board.d/02_network b/target/linux/ar71xx/base-files/etc/board.d/02_network
index f131b3b..0fe71e0 100755
--- a/target/linux/ar71xx/base-files/etc/board.d/02_network
+++ b/target/linux/ar71xx/base-files/etc/board.d/02_network
@@ -355,6 +355,12 @@ ar71xx_setup_interfaces()
"0u at eth0" "2:lan" "3:lan" "4:lan"
ucidef_add_switch_attr "switch0" "enable" "false"
;;
+ e1700ac-v2|\
+ unifiac-pro|\
+ xd3200)
+ ucidef_add_switch "switch0" \
+ "0 at eth0" "2:lan" "3:wan"
+ ;;
ebr-2310-c1)
ucidef_set_interfaces_lan_wan "eth0.1" "eth1"
ucidef_add_switch "switch0" \
@@ -493,11 +499,6 @@ ar71xx_setup_interfaces()
ucidef_add_switch "switch0" \
"0 at eth0" "1:lan" "2:wan"
;;
- unifiac-pro|\
- xd3200)
- ucidef_add_switch "switch0" \
- "0 at eth0" "2:lan" "3:wan"
- ;;
wndr3700|\
wndr3700v2|\
wndr3800|\
diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh
index 3b5fc32..facc77e 100644
--- a/target/linux/ar71xx/base-files/etc/diag.sh
+++ b/target/linux/ar71xx/base-files/etc/diag.sh
@@ -23,6 +23,8 @@ get_status_led() {
antminer-s1|\
antminer-s3|\
antminer-r1|\
+ e1700ac-v2|\
+ e600gac-v2|\
eap120|\
minibox-v1|\
som9331|\
@@ -199,6 +201,9 @@ get_status_led() {
r36a)
status_led="$board:blue:status"
;;
+ e600g-v2)
+ status_led="$board:blue:system"
+ ;;
eap300v2)
status_led="engenius:blue:power"
;;
diff --git a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 8284550..b0ada3b 100644
--- a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -67,6 +67,8 @@ case "$FIRMWARE" in
cf-e380ac-v1|\
cf-e380ac-v2|\
dlan-pro-1200-ac|\
+ e1700ac-v2|\
+ e600gac-v2|\
sr3200|\
xd3200)
ath10kcal_extract "art" 20480 2116
diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh
index f0742c1..a9c6821 100755
--- a/target/linux/ar71xx/base-files/lib/ar71xx.sh
+++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh
@@ -627,9 +627,18 @@ ar71xx_board_detect() {
*"DW33D")
name="dw33d"
;;
+ *"E1700AC v2")
+ name="e1700ac-v2"
+ ;;
*"E2100L")
name="e2100l"
;;
+ *"E600G v2")
+ name="e600g-v2"
+ ;;
+ *"E600GAC v2")
+ name="e600gac-v2"
+ ;;
*"EAP120")
name="eap120"
tplink_pharos_board_detect
diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
index 88d0f29..614692d 100755
--- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
@@ -233,6 +233,9 @@ platform_check_image() {
dr342|\
dr531|\
dragino2|\
+ e1700ac-v2|\
+ e600g-v2|\
+ e600gac-v2|\
ebr-2310-c1|\
ens202ext|\
epg5000|\
diff --git a/target/linux/ar71xx/config-4.4 b/target/linux/ar71xx/config-4.4
index 068b83c..ec398a7 100644
--- a/target/linux/ar71xx/config-4.4
+++ b/target/linux/ar71xx/config-4.4
@@ -99,7 +99,9 @@ CONFIG_ATH79=y
# CONFIG_ATH79_MACH_DR344 is not set
# CONFIG_ATH79_MACH_DR531 is not set
# CONFIG_ATH79_MACH_DRAGINO2 is not set
+# CONFIG_ATH79_MACH_E1700AC_V2 is not set
# CONFIG_ATH79_MACH_E2100L is not set
+# CONFIG_ATH79_MACH_E600G_V2 is not set
# CONFIG_ATH79_MACH_EAP120 is not set
# CONFIG_ATH79_MACH_EAP300V2 is not set
# CONFIG_ATH79_MACH_EAP7660D is not set
diff --git a/target/linux/ar71xx/config-4.9 b/target/linux/ar71xx/config-4.9
index e495f6b..924f17c 100644
--- a/target/linux/ar71xx/config-4.9
+++ b/target/linux/ar71xx/config-4.9
@@ -97,7 +97,9 @@ CONFIG_ATH79=y
# CONFIG_ATH79_MACH_DR344 is not set
# CONFIG_ATH79_MACH_DR531 is not set
# CONFIG_ATH79_MACH_DRAGINO2 is not set
+# CONFIG_ATH79_MACH_E1700AC_V2 is not set
# CONFIG_ATH79_MACH_E2100L is not set
+# CONFIG_ATH79_MACH_E600G_V2 is not set
# CONFIG_ATH79_MACH_EAP120 is not set
# CONFIG_ATH79_MACH_EAP300V2 is not set
# CONFIG_ATH79_MACH_EAP7660D is not set
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
index fca5d01..ad4e2a2 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
+++ b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
@@ -689,6 +689,17 @@ config ATH79_MACH_DRAGINO2
select ATH79_DEV_ETH
select ATH79_DEV_USB
+config ATH79_MACH_E1700AC_V2
+ bool "WHQX E1700AC v2 support"
+ select SOC_QCA956X
+ select ATH79_DEV_AP9X_PCI if PCI
+ select ATH79_DEV_ETH
+ select ATH79_DEV_GPIO_BUTTONS
+ select ATH79_DEV_LEDS_GPIO
+ select ATH79_DEV_M25P80
+ select ATH79_DEV_USB
+ select ATH79_DEV_WMAC
+
config ATH79_MACH_E2100L
bool "Linksys E2100L board support"
select SOC_AR913X
@@ -700,6 +711,17 @@ config ATH79_MACH_E2100L
select ATH79_DEV_WMAC
select ATH79_NVRAM
+config ATH79_MACH_E600G_V2
+ bool "WHQX E600G/E600GAC v2 support"
+ select SOC_QCA953X
+ select ATH79_DEV_AP9X_PCI if PCI
+ select ATH79_DEV_ETH
+ select ATH79_DEV_GPIO_BUTTONS
+ select ATH79_DEV_LEDS_GPIO
+ select ATH79_DEV_M25P80
+ select ATH79_DEV_USB
+ select ATH79_DEV_WMAC
+
config ATH79_MACH_ESR900
bool "EnGenius ESR900 board support"
select SOC_QCA955X
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Makefile b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
index 98d4677..d489b1a 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/Makefile
+++ b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
@@ -108,6 +108,8 @@ obj-$(CONFIG_ATH79_MACH_DR342) += mach-dr344.o
obj-$(CONFIG_ATH79_MACH_DR344) += mach-dr344.o
obj-$(CONFIG_ATH79_MACH_DR531) += mach-dr531.o
obj-$(CONFIG_ATH79_MACH_DRAGINO2) += mach-dragino2.o
+obj-$(CONFIG_ATH79_MACH_E1700AC_V2) += mach-e1700ac-v2.o
+obj-$(CONFIG_ATH79_MACH_E600G_V2) += mach-e600g-v2.o
obj-$(CONFIG_ATH79_MACH_EAP120) += mach-eap120.o
obj-$(CONFIG_ATH79_MACH_EAP300V2) += mach-eap300v2.o
obj-$(CONFIG_ATH79_MACH_EAP7660D) += mach-eap7660d.o
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-e1700ac-v2.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-e1700ac-v2.c
new file mode 100644
index 0000000..584fd51
--- /dev/null
+++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-e1700ac-v2.c
@@ -0,0 +1,145 @@
+/*
+ * WHQX E1700AC v2 board support
+ *
+ * Copyright (C) 2017 Peng Zhang <sd20 at qxwlan.com>
+ * Copyright (C) 2018 Piotr Dymacz <pepe2k at gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/ar8216_platform.h>
+
+#include "common.h"
+#include "dev-eth.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-m25p80.h"
+#include "dev-usb.h"
+#include "dev-wmac.h"
+#include "machtypes.h"
+#include "pci.h"
+
+#define E1700AC_V2_GPIO_LED_SYS 1
+#define E1700AC_V2_GPIO_LED_USB 7
+#define E1700AC_V2_GPIO_LED_WLAN2G 19
+
+#define E1700AC_V2_GPIO_BTN_SW1 2
+#define E1700AC_V2_GPIO_BTN_RESET 11
+
+#define E1700AC_V2_KEYS_POLL_INTERVAL 20 /* msecs */
+#define E1700AC_V2_KEYS_DEBOUNCE_INTERVAL \
+ (3 * E1700AC_V2_KEYS_POLL_INTERVAL)
+
+static struct gpio_led e1700ac_v2_leds_gpio[] __initdata = {
+ {
+ .name = "e1700ac-v2:green:system",
+ .gpio = E1700AC_V2_GPIO_LED_SYS,
+ .active_low = 1,
+ }, {
+ .name = "e1700ac-v2:green:usb",
+ .gpio = E1700AC_V2_GPIO_LED_USB,
+ .active_low = 1,
+ }, {
+ .name = "e1700ac-v2:green:wlan2g",
+ .gpio = E1700AC_V2_GPIO_LED_WLAN2G,
+ .active_low = 1,
+ },
+};
+
+static struct gpio_keys_button e1700ac_v2_gpio_keys[] __initdata = {
+ {
+ .desc = "reset",
+ .type = EV_KEY,
+ .code = KEY_RESTART,
+ .debounce_interval = E1700AC_V2_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = E1700AC_V2_GPIO_BTN_RESET,
+ .active_low = 1,
+ }, {
+ .desc = "sw1",
+ .type = EV_KEY,
+ .code = BTN_0,
+ .debounce_interval = E1700AC_V2_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = E1700AC_V2_GPIO_BTN_SW1,
+ .active_low = 1,
+ },
+};
+
+static const struct ar8327_led_info e1700ac_v2_leds_qca8334[] = {
+ AR8327_LED_INFO(PHY1_0, HW, "e1700ac-v2:green:lan"),
+ AR8327_LED_INFO(PHY2_0, HW, "e1700ac-v2:green:wan"),
+};
+
+/* Blink rate: 1 Gbps -> 8 hz, 100 Mbs -> 4 Hz, 10 Mbps -> 2 Hz */
+static struct ar8327_led_cfg e1700ac_v2_qca8334_led_cfg = {
+ .led_ctrl0 = 0xcf37cf37,
+ .led_ctrl1 = 0xcf37cf37,
+ .led_ctrl2 = 0xcf37cf37,
+ .led_ctrl3 = 0x0,
+ .open_drain = true,
+};
+
+static struct ar8327_pad_cfg e1700ac_v2_qca8334_pad0_cfg = {
+ .mode = AR8327_PAD_MAC_SGMII,
+ .sgmii_delay_en = true,
+};
+
+static struct ar8327_platform_data e1700ac_v2_qca8334_data = {
+ .pad0_cfg = &e1700ac_v2_qca8334_pad0_cfg,
+ .port0_cfg = {
+ .force_link = 1,
+ .speed = AR8327_PORT_SPEED_1000,
+ .duplex = 1,
+ .txpause = 1,
+ .rxpause = 1,
+ },
+ .led_cfg = &e1700ac_v2_qca8334_led_cfg,
+ .leds = e1700ac_v2_leds_qca8334,
+ .num_leds = ARRAY_SIZE(e1700ac_v2_leds_qca8334),
+};
+
+static struct mdio_board_info e1700ac_v2_mdio0_info[] = {
+ {
+ .bus_id = "ag71xx-mdio.0",
+ .phy_addr = 0,
+ .platform_data = &e1700ac_v2_qca8334_data,
+ },
+};
+
+static void __init e1700ac_v2_setup(void)
+{
+ u8 *mac = (u8 *) KSEG1ADDR(0x1f050400);
+ u8 *art = (u8 *) KSEG1ADDR(0x1f061000);
+
+ ath79_register_m25p80(NULL);
+
+ ath79_register_leds_gpio(-1, ARRAY_SIZE(e1700ac_v2_leds_gpio),
+ e1700ac_v2_leds_gpio);
+
+ ath79_register_gpio_keys_polled(-1, E1700AC_V2_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(e1700ac_v2_gpio_keys),
+ e1700ac_v2_gpio_keys);
+
+ ath79_register_mdio(0, 0x0);
+ mdiobus_register_board_info(e1700ac_v2_mdio0_info,
+ ARRAY_SIZE(e1700ac_v2_mdio0_info));
+
+ /* GMAC0 is connected to QCA8334 switch */
+ ath79_eth0_data.duplex = DUPLEX_FULL;
+ ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
+ ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_SGMII;
+ ath79_eth0_data.phy_mask = BIT(0);
+ ath79_eth0_data.speed = SPEED_1000;
+ ath79_eth0_pll_data.pll_1000 = 0x03000101;
+ ath79_init_mac(ath79_eth0_data.mac_addr, mac, 0);
+ ath79_register_eth(0);
+
+ ath79_register_pci();
+ ath79_register_usb();
+ ath79_register_wmac(art, NULL);
+}
+
+MIPS_MACHINE(ATH79_MACH_E1700AC_V2, "E1700AC-V2", "WHQX E1700AC v2",
+ e1700ac_v2_setup);
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-e600g-v2.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-e600g-v2.c
new file mode 100644
index 0000000..9838c30
--- /dev/null
+++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-e600g-v2.c
@@ -0,0 +1,184 @@
+/*
+ * WHQX E600G/E600GAC v2 board support
+ *
+ * Copyright (C) 2017 Peng Zhang <sd20 at qxwlan.com>
+ * Copyright (C) 2018 Piotr Dymacz <pepe2k at gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "common.h"
+#include "dev-eth.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-m25p80.h"
+#include "dev-usb.h"
+#include "dev-wmac.h"
+#include "machtypes.h"
+#include "pci.h"
+
+#define E600G_V2_GPIO_LED_LAN 16
+#define E600G_V2_GPIO_LED_SYS 13
+#define E600G_V2_GPIO_LED_WAN_B 4
+#define E600G_V2_GPIO_LED_WAN_G 15
+
+#define E600GAC_V2_GPIO_LED_CTRL_B 14
+#define E600GAC_V2_GPIO_LED_CTRL_G 11
+#define E600GAC_V2_GPIO_LED_CTRL_R 12
+#define E600GAC_V2_GPIO_LED_LAN 16
+#define E600GAC_V2_GPIO_LED_SYS 13
+#define E600GAC_V2_GPIO_LED_WAN_G 15
+#define E600GAC_V2_GPIO_LED_WAN_O 4
+
+#define E600G_V2_GPIO_BTN_RESET 17
+#define E600GAC_V2_GPIO_BTN_WPS 1
+
+#define E600G_V2_KEYS_POLL_INTERVAL 20 /* msecs */
+#define E600G_V2_KEYS_DEBOUNCE_INTERVAL (3 * E600G_V2_KEYS_POLL_INTERVAL)
+
+static struct gpio_led e600g_v2_leds_gpio[] __initdata = {
+ {
+ .name = "e600g-v2:blue:system",
+ .gpio = E600G_V2_GPIO_LED_SYS,
+ .active_low = 1,
+ }, {
+ .name = "e600g-v2:blue:wan",
+ .gpio = E600G_V2_GPIO_LED_WAN_B,
+ .active_low = 1,
+ }, {
+ .name = "e600g-v2:green:lan",
+ .gpio = E600G_V2_GPIO_LED_LAN,
+ .active_low = 1,
+ }, {
+ .name = "e600g-v2:green:wan",
+ .gpio = E600G_V2_GPIO_LED_WAN_G,
+ .active_low = 1,
+ },
+};
+
+static struct gpio_led e600gac_v2_leds_gpio[] __initdata = {
+ {
+ .name = "e600gac-v2:blue:control",
+ .gpio = E600GAC_V2_GPIO_LED_CTRL_B,
+ .active_low = 1,
+ }, {
+ .name = "e600gac-v2:green:control",
+ .gpio = E600GAC_V2_GPIO_LED_CTRL_G,
+ .active_low = 1,
+ }, {
+ .name = "e600gac-v2:red:control",
+ .gpio = E600GAC_V2_GPIO_LED_CTRL_R,
+ .active_low = 1,
+ }, {
+ .name = "e600gac-v2:green:system",
+ .gpio = E600GAC_V2_GPIO_LED_SYS,
+ .active_low = 1,
+ }, {
+ .name = "e600gac-v2:orange:wan",
+ .gpio = E600GAC_V2_GPIO_LED_WAN_O,
+ .active_low = 1,
+ }, {
+ .name = "e600gac-v2:green:lan",
+ .gpio = E600GAC_V2_GPIO_LED_LAN,
+ .active_low = 1,
+ }, {
+ .name = "e600gac-v2:green:wan",
+ .gpio = E600GAC_V2_GPIO_LED_WAN_G,
+ .active_low = 1,
+ },
+};
+
+static struct gpio_keys_button e600g_v2_gpio_keys[] __initdata = {
+ {
+ .desc = "reset",
+ .type = EV_KEY,
+ .code = KEY_RESTART,
+ .debounce_interval = E600G_V2_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = E600G_V2_GPIO_BTN_RESET,
+ .active_low = 1,
+ },
+};
+
+static struct gpio_keys_button e600gac_v2_gpio_keys[] __initdata = {
+ {
+ .desc = "reset",
+ .type = EV_KEY,
+ .code = KEY_RESTART,
+ .debounce_interval = E600G_V2_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = E600G_V2_GPIO_BTN_RESET,
+ .active_low = 1,
+ }, {
+ .desc = "wps",
+ .type = EV_KEY,
+ .code = KEY_WPS_BUTTON,
+ .debounce_interval = E600G_V2_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = E600GAC_V2_GPIO_BTN_WPS,
+ .active_low = 1,
+ },
+};
+
+static void __init e600g_v2_common_setup(void)
+{
+ u8 *mac = (u8 *) KSEG1ADDR(0x1f050400);
+ u8 *art = (u8 *) KSEG1ADDR(0x1f061000);
+
+ ath79_register_m25p80(NULL);
+
+ ath79_setup_ar933x_phy4_switch(false, false);
+
+ ath79_register_mdio(0, 0x0);
+
+ ath79_switch_data.phy4_mii_en = 1;
+ ath79_switch_data.phy_poll_mask = 0xfe;
+
+ /* LAN */
+ ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
+ ath79_eth0_data.phy_mask = BIT(4);
+ ath79_eth0_data.speed = SPEED_100;
+ ath79_init_mac(ath79_eth0_data.mac_addr, mac, 1);
+ ath79_register_eth(0);
+
+ /* WAN */
+ ath79_eth1_data.duplex = DUPLEX_FULL;
+ ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII;
+ ath79_eth1_data.phy_mask = BIT(0);
+ ath79_eth1_data.speed = SPEED_1000;
+ ath79_init_mac(ath79_eth1_data.mac_addr, mac, 0);
+ ath79_register_eth(1);
+
+ ath79_register_pci();
+ ath79_register_usb();
+ ath79_register_wmac(art, NULL);
+}
+
+static void __init e600g_v2_setup(void)
+{
+ e600g_v2_common_setup();
+
+ ath79_register_leds_gpio(-1, ARRAY_SIZE(e600g_v2_leds_gpio),
+ e600g_v2_leds_gpio);
+
+ ath79_register_gpio_keys_polled(-1, E600G_V2_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(e600g_v2_gpio_keys),
+ e600g_v2_gpio_keys);
+}
+
+static void __init e600gac_v2_setup(void)
+{
+ e600g_v2_common_setup();
+
+ ath79_register_leds_gpio(-1, ARRAY_SIZE(e600gac_v2_leds_gpio),
+ e600gac_v2_leds_gpio);
+
+ ath79_register_gpio_keys_polled(-1, E600G_V2_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(e600gac_v2_gpio_keys),
+ e600gac_v2_gpio_keys);
+}
+
+MIPS_MACHINE(ATH79_MACH_E600G_V2, "E600G-V2", "WHQX E600G v2",
+ e600g_v2_setup);
+
+MIPS_MACHINE(ATH79_MACH_E600GAC_V2, "E600GAC-V2", "WHQX E600GAC v2",
+ e600gac_v2_setup);
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
index 497d794..e22ebd0 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
+++ b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
@@ -98,6 +98,9 @@ enum ath79_mach_type {
ATH79_MACH_DR344, /* Wallys DR344 */
ATH79_MACH_DR531, /* Wallys DR531 */
ATH79_MACH_DRAGINO2, /* Dragino Version 2 */
+ ATH79_MACH_E1700AC_V2, /* WHQX E1700AC v2 */
+ ATH79_MACH_E600G_V2, /* WHQX E600G v2 */
+ ATH79_MACH_E600GAC_V2, /* WHQX E600GAC v2 */
ATH79_MACH_EAP120, /* TP-LINK EAP120 */
ATH79_MACH_EAP300V2, /* EnGenius EAP300 v2 */
ATH79_MACH_EAP7660D, /* Senao EAP7660D */
diff --git a/target/linux/ar71xx/generic/config-default b/target/linux/ar71xx/generic/config-default
index 9caf29a..2e5eb66 100644
--- a/target/linux/ar71xx/generic/config-default
+++ b/target/linux/ar71xx/generic/config-default
@@ -70,7 +70,9 @@ CONFIG_ATH79_MACH_DR342=y
CONFIG_ATH79_MACH_DR344=y
CONFIG_ATH79_MACH_DR531=y
CONFIG_ATH79_MACH_DRAGINO2=y
+CONFIG_ATH79_MACH_E1700AC_V2=y
CONFIG_ATH79_MACH_E2100L=y
+CONFIG_ATH79_MACH_E600G_V2=y
CONFIG_ATH79_MACH_EAP120=y
CONFIG_ATH79_MACH_EAP300V2=y
CONFIG_ATH79_MACH_EAP7660D=y
diff --git a/target/linux/ar71xx/image/generic.mk b/target/linux/ar71xx/image/generic.mk
index eeefde0..beb56bd 100644
--- a/target/linux/ar71xx/image/generic.mk
+++ b/target/linux/ar71xx/image/generic.mk
@@ -281,6 +281,65 @@ define Device/dragino2
endef
TARGET_DEVICES += dragino2
+define Device/e1700ac-v2-16M
+ DEVICE_TITLE := WHQX E1700AC v2 (16MB flash)
+ DEVICE_PACKAGES := kmod-ath10k ath10k-firmware-qca988x kmod-usb-core \
+ kmod-usb2 kmod-usb-ledtrig-usbport
+ BOARDNAME := E1700AC-V2
+ SUPPORTED_DEVICES := e1700ac-v2
+ IMAGE_SIZE := 15936k
+ MTDPARTS := spi0.0:256k(u-boot)ro,64k(u-boot-env),64k(pri-data)ro,64k(art)ro,-(firmware)
+ IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) |\
+ append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
+endef
+TARGET_DEVICES += e1700ac-v2-16M
+
+define Device/e1700ac-v2-8M
+ $(Device/e1700ac-v2-16M)
+ DEVICE_TITLE := WHQX E1700AC v2 (8MB flash)
+ IMAGE_SIZE := 7744k
+endef
+TARGET_DEVICES += e1700ac-v2-8M
+
+define Device/e600g-v2-16M
+ DEVICE_TITLE := WHQX E600G v2 (16MB flash)
+ DEVICE_PACKAGES := kmod-usb-core kmod-usb2 -swconfig
+ BOARDNAME := E600G-V2
+ SUPPORTED_DEVICES := e600g-v2
+ IMAGE_SIZE := 15936k
+ MTDPARTS := spi0.0:256k(u-boot)ro,64k(u-boot-env),64k(pri-data)ro,64k(art)ro,-(firmware)
+ IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) |\
+ append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
+endef
+TARGET_DEVICES += e600g-v2-16M
+
+define Device/e600g-v2-8M
+ $(Device/e600g-v2-16M)
+ DEVICE_TITLE := WHQX E600G v2 (8MB flash)
+ IMAGE_SIZE := 7744k
+endef
+TARGET_DEVICES += e600g-v2-8M
+
+define Device/e600gac-v2-16M
+ DEVICE_TITLE := WHQX E600GAC v2 (16MB flash)
+ DEVICE_PACKAGES := kmod-ath10k ath10k-firmware-qca9887 kmod-usb-core \
+ kmod-usb2 -swconfig
+ BOARDNAME := E600GAC-V2
+ SUPPORTED_DEVICES := e600gac-v2
+ IMAGE_SIZE := 15936k
+ MTDPARTS := spi0.0:256k(u-boot)ro,64k(u-boot-env),64k(pri-data)ro,64k(art)ro,-(firmware)
+ IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) |\
+ append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
+endef
+TARGET_DEVICES += e600gac-v2-16M
+
+define Device/e600gac-v2-8M
+ $(Device/e600gac-v2-16M)
+ DEVICE_TITLE := WHQX E600GAC v2 (8MB flash)
+ IMAGE_SIZE := 7744k
+endef
+TARGET_DEVICES += e600gac-v2-8M
+
define Device/ew-balin
DEVICE_TITLE := Embedded Wireless Balin Platform
DEVICE_PACKAGES := kmod-usb-core kmod-usb-chipidea
More information about the lede-commits
mailing list