[openwrt/openwrt] ipq40xx: add support for Netgear EX6100v2/EX6150v2
LEDE Commits
lede-commits at lists.infradead.org
Thu Apr 12 22:54:41 PDT 2018
mkresin pushed a commit to openwrt/openwrt.git, branch master:
https://git.lede-project.org/970f1914be3f299fb302ca74a214589397000858
commit 970f1914be3f299fb302ca74a214589397000858
Author: David Bauer <mail at david-bauer.net>
AuthorDate: Thu Mar 29 00:32:38 2018 +0200
ipq40xx: add support for Netgear EX6100v2/EX6150v2
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MB Winbond W632GU6KB12J
FLASH: 16 MiB Macronix MX25L12805D
ETH: Qualcomm QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac
1x1 (EX6100)
2x2 (EX6150)
INPUT: Power, WPS, reset button
AP / Range-extender toggle
LED: Power, Router, Extender (dual), WPS, Left-/Right-arrow
SERIAL: Header next to QCA8072 chip.
VCC, TX, RX, GND (Square hole is VCC)
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from WebIF
- Factory installation from tftp
- OpenWRT sysupgrade (Preserving and non-preserving)
- LEDs
- Buttons
Not Working:
- AP/Extender toggle-switch
Untested:
- Support on EX6100v2. They share the same GPL-Code and vendor-images.
The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz
board-blob. I only own a EX6150v2, therefore i am only able to verify
functionality on this device.
Install via Web-Interface:
Upload the factory image to the device to the Netgear Web-Interface.
The device might asks you to confirm the update a second time due to
detecting the OpenWRT firmware as older. The device will automatically
reboot after the image is written to flash.
Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command "fw_recovery" will start a tftp server, waiting for
a DNI image to be pushed.
Assign your computer the IP-address 192.168.1.10/24. Push image with
tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY>
Device will erase factory-partition first, then writes the pushed image
to flash and reboots.
Parts of this commit are based on Thomas Hebb's work on the
openwrt-devel mailinglist.
See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html
Signed-off-by: David Bauer <mail at david-bauer.net>
---
package/firmware/ipq-wifi/Makefile | 3 +-
.../firmware/ipq-wifi/board-netgear_ex61x0v2.bin | Bin 0 -> 48628 bytes
.../linux/ipq40xx/base-files/etc/board.d/01_leds | 5 +
.../ipq40xx/base-files/etc/board.d/02_network | 5 +-
.../etc/hotplug.d/firmware/11-ath10k-caldata | 10 +
target/linux/ipq40xx/config-4.14 | 2 +
.../arch/arm/boot/dts/qcom-ipq4018-ex6100v2.dts | 33 +++
.../arch/arm/boot/dts/qcom-ipq4018-ex6150v2.dts | 33 +++
.../arch/arm/boot/dts/qcom-ipq4018-ex61x0v2.dtsi | 322 +++++++++++++++++++++
target/linux/ipq40xx/image/Makefile | 35 +++
.../patches-4.14/069-arm-boot-add-dts-files.patch | 4 +-
11 files changed, 448 insertions(+), 4 deletions(-)
diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile
index 7cc6478..0df5078 100644
--- a/package/firmware/ipq-wifi/Makefile
+++ b/package/firmware/ipq-wifi/Makefile
@@ -13,7 +13,7 @@ endef
define Build/Compile
endef
-ALLWIFIBOARDS:=8dev_jalapeno asus_rt-ac58u avm_fritzbox-4040 glinet_gl-b1300 meraki_mr33
+ALLWIFIBOARDS:=8dev_jalapeno asus_rt-ac58u avm_fritzbox-4040 glinet_gl-b1300 meraki_mr33 netgear_ex61x0v2
ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
define Package/ipq-wifi-default
@@ -52,5 +52,6 @@ $(eval $(call generate-ipq-wifi-package,asus_rt-ac58u,board-asus_rt-ac58u.bin,AS
$(eval $(call generate-ipq-wifi-package,avm_fritzbox-4040,board-avm_fritzbox-4040.bin,AVM FRITZ!Box 4040))
$(eval $(call generate-ipq-wifi-package,glinet_gl-b1300,board-glinet_gl-b1300.bin,GL.iNet GL-B1300))
$(eval $(call generate-ipq-wifi-package,meraki_mr33,board-meraki_mr33.bin,Cisco Meraki MR33))
+$(eval $(call generate-ipq-wifi-package,netgear_ex61x0v2,board-netgear_ex61x0v2.bin,Netgear EX61x0v2))
$(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))
diff --git a/package/firmware/ipq-wifi/board-netgear_ex61x0v2.bin b/package/firmware/ipq-wifi/board-netgear_ex61x0v2.bin
new file mode 100644
index 0000000..0937a65
Binary files /dev/null and b/package/firmware/ipq-wifi/board-netgear_ex61x0v2.bin differ
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/01_leds b/target/linux/ipq40xx/base-files/etc/board.d/01_leds
index f1f49ab..784fd44 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq40xx/base-files/etc/board.d/01_leds
@@ -26,6 +26,11 @@ avm,fritzbox-4040)
glinet,gl-b1300)
ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:green:wlan" "phy0tpt"
;;
+netgear,ex6100v2 |\
+netgear,ex6150v2)
+ ucidef_set_led_wlan "wlan2g" "WLAN2G" "ex61x0v2:green:router" "phy0tpt"
+ ucidef_set_led_wlan "wlan5g" "WLAN5G" "ex61x0v2:green:client" "phy1tpt"
+ ;;
meraki,mr33)
ucidef_set_interface_lan "eth0"
;;
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 91343cd..ade1b05 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -41,8 +41,9 @@ glinet,gl-b1300)
openmesh,a42)
ucidef_set_interfaces_lan_wan "eth1" "eth0"
;;
-
-meraki,mr33)
+meraki,mr33 |\
+netgear,ex6100v2 |\
+netgear,ex6150v2)
ucidef_set_interface_lan "eth0"
;;
*)
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 56c10cb..0a5780c 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -129,6 +129,11 @@ case "$FIRMWARE" in
ath10kcal_is_caldata_valid "202f" || ath10kcal_extract "ART" 4096 12064
ath10kcal_patch_mac_crc $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 102) +2)
;;
+ netgear,ex6100v2 |\
+ netgear,ex6150v2)
+ ath10kcal_extract "ART" 4096 12064
+ ath10kcal_patch_mac_crc $(mtd_get_mac_binary dnidata 0)
+ ;;
compex,wpj428 |\
openmesh,a42)
ath10kcal_extract "0:ART" 4096 12064
@@ -154,6 +159,11 @@ case "$FIRMWARE" in
ath10kcal_is_caldata_valid "202f" || ath10kcal_extract "ART" 20480 12064
ath10kcal_patch_mac_crc $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 102) +3)
;;
+ netgear,ex6100v2 |\
+ netgear,ex6150v2)
+ ath10kcal_extract "ART" 20480 12064
+ ath10kcal_patch_mac_crc $(mtd_get_mac_binary dnidata 12)
+ ;;
compex,wpj428 |\
openmesh,a42)
ath10kcal_extract "0:ART" 20480 12064
diff --git a/target/linux/ipq40xx/config-4.14 b/target/linux/ipq40xx/config-4.14
index 1bba061..18a8baf 100644
--- a/target/linux/ipq40xx/config-4.14
+++ b/target/linux/ipq40xx/config-4.14
@@ -191,6 +191,7 @@ CONFIG_GENERIC_STRNLEN_USER=y
CONFIG_GENERIC_TIME_VSYSCALL=y
CONFIG_GPIOLIB=y
CONFIG_GPIOLIB_IRQCHIP=y
+CONFIG_GPIO_74X164=y
CONFIG_GPIO_SYSFS=y
CONFIG_GPIO_WATCHDOG=y
# CONFIG_GPIO_WATCHDOG_ARCH_INITCALL is not set
@@ -438,6 +439,7 @@ CONFIG_SMP_ON_UP=y
CONFIG_SPARSE_IRQ=y
CONFIG_SPI=y
CONFIG_SPI_MASTER=y
+CONFIG_SPI_GPIO=y
CONFIG_SPI_QUP=y
CONFIG_SPMI=y
CONFIG_SPMI_MSM_PMIC_ARB=y
diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ex6100v2.dts b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ex6100v2.dts
new file mode 100644
index 0000000..a0abe41
--- /dev/null
+++ b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ex6100v2.dts
@@ -0,0 +1,33 @@
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2018, David Bauer <mail at david-bauer.net>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include "qcom-ipq4018-ex61x0v2.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Netgear EX6100v2";
+ compatible = "netgear,ex6100v2", "qcom,ipq4019";
+};
+
+&wifi0 {
+ qcom,ath10k-calibration-variant = "Netgear-EX6100v2";
+};
+
+&wifi1 {
+ qcom,ath10k-calibration-variant = "Netgear-EX6100v2";
+};
diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ex6150v2.dts b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ex6150v2.dts
new file mode 100644
index 0000000..e0b5c38
--- /dev/null
+++ b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ex6150v2.dts
@@ -0,0 +1,33 @@
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2018, David Bauer <mail at david-bauer.net>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include "qcom-ipq4018-ex61x0v2.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Netgear EX6150v2";
+ compatible = "netgear,ex6150v2", "qcom,ipq4019";
+};
+
+&wifi0 {
+ qcom,ath10k-calibration-variant = "Netgear-EX6150v2";
+};
+
+&wifi1 {
+ qcom,ath10k-calibration-variant = "Netgear-EX6150v2";
+};
diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ex61x0v2.dtsi b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ex61x0v2.dtsi
new file mode 100644
index 0000000..14c1caa
--- /dev/null
+++ b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ex61x0v2.dtsi
@@ -0,0 +1,322 @@
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2018, David Bauer <mail at david-bauer.net>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include "qcom-ipq4019.dtsi"
+#include "qcom-ipq4019-bus.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "Netgear EX61X0v2";
+ compatible = "netgear,ex61x0v2", "qcom,ipq4019";
+
+ reserved-memory {
+ #address-cells = <0x1>;
+ #size-cells = <0x1>;
+ ranges;
+
+ smem at 87e00000 {
+ reg = <0x87e00000 0x080000>;
+ no-map;
+ };
+
+ tz at 87e80000 {
+ reg = <0x87e80000 0x180000>;
+ no-map;
+ };
+ };
+
+ soc {
+ mdio at 90000 {
+ status = "okay";
+ };
+
+ ess-psgmii at 98000 {
+ status = "okay";
+ };
+
+ tcsr at 1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ ess_tcsr at 1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr at 1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ serial at 78af000 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ crypto at 8e3a000 {
+ status = "okay";
+ };
+
+ watchdog at b017000 {
+ status = "okay";
+ };
+
+ ess-switch at c000000 {
+ status = "okay";
+ };
+
+ edma at c080000 {
+ status = "okay";
+ };
+ };
+
+ aliases {
+ led-boot = &power_amber;
+ led-failsafe = &power_amber;
+ led-running = &power_green;
+ led-upgrade = &power_amber;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ wps {
+ label = "wps";
+ gpios = <&tlmm 0 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ led_spi {
+ compatible = "spi-gpio";
+ #address-cells = <1>;
+ ranges;
+
+ gpio-sck = <&tlmm 5 GPIO_ACTIVE_HIGH>;
+ gpio-mosi = <&tlmm 4 GPIO_ACTIVE_HIGH>;
+ num-chipselects = <0>;
+
+ led_gpio: led_gpio at 0 {
+ compatible = "fairchild,74hc595";
+ reg = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ registers-number = <1>;
+ spi-max-frequency = <1000000>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ power_amber: power_amber {
+ label = "ex61x0v2:amber:power";
+ gpios = <&led_gpio 7 GPIO_ACTIVE_LOW>;
+ };
+
+ power_green: power_green {
+ label = "ex61x0v2:green:power";
+ gpios = <&led_gpio 6 GPIO_ACTIVE_LOW>;
+ };
+
+ right {
+ label = "ex61x0v2:blue:right";
+ gpios = <&led_gpio 5 GPIO_ACTIVE_LOW>;
+ };
+
+ left {
+ label = "ex61x0v2:blue:left";
+ gpios = <&led_gpio 4 GPIO_ACTIVE_LOW>;
+ };
+
+ client_green {
+ label = "ex61x0v2:green:client";
+ gpios = <&led_gpio 3 GPIO_ACTIVE_LOW>;
+ };
+
+ client_red {
+ label = "ex61x0v2:red:client";
+ gpios = <&led_gpio 2 GPIO_ACTIVE_LOW>;
+ };
+
+ router_green {
+ label = "ex61x0v2:green:router";
+ gpios = <&led_gpio 1 GPIO_ACTIVE_LOW>;
+ };
+
+ router_red {
+ label = "ex61x0v2:red:router";
+ gpios = <&led_gpio 0 GPIO_ACTIVE_LOW>;
+ };
+
+ wps {
+ label = "ex61x0v2:green:wps";
+ gpios = <&tlmm 1 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&tlmm {
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pin {
+ function = "blsp_spi0";
+ pins = "gpio55", "gpio56", "gpio57";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pin_cs {
+ function = "gpio";
+ pins = "gpio54";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&spi_0 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+ mx25l12805d at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition0 at 0 {
+ label = "SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+
+ partition1 at 40000 {
+ label = "MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+
+ partition2 at 60000 {
+ label = "QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+
+ partition3 at c0000 {
+ label = "CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+
+ partition4 at d0000 {
+ label = "DDRPARAMS";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+
+ partition5 at E0000 {
+ label = "APPSBLENV";
+ reg = <0x000e0000 0x00010000>;
+ read-only;
+ };
+
+ partition6 at F0000 {
+ label = "APPSBL";
+ reg = <0x000f0000 0x00080000>;
+ read-only;
+ };
+
+ partition7 at 170000 {
+ label = "ART";
+ reg = <0x00170000 0x00010000>;
+ read-only;
+ };
+
+ partition8 at 180000 {
+ label = "config";
+ reg = <0x00180000 0x00010000>;
+ read-only;
+ };
+
+ partition9 at 190000 {
+ label = "pot";
+ reg = <0x00190000 0x00010000>;
+ read-only;
+ };
+
+ partition10 at 1a0000 {
+ label = "dnidata";
+ reg = <0x001a0000 0x00010000>;
+ read-only;
+ };
+
+ partition11 at 1b0000 {
+ label = "firmware";
+ reg = <0x001b0000 0x00e10000>;
+ };
+
+ partition12 at fc0000 {
+ label = "language";
+ reg = <0x00fc0000 0x00040000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+};
+
+&wifi1 {
+ status = "okay";
+};
diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile
index 87545d0..c13516e 100644
--- a/target/linux/ipq40xx/image/Makefile
+++ b/target/linux/ipq40xx/image/Makefile
@@ -31,6 +31,18 @@ define Device/UbiFit
IMAGE/nand-sysupgrade.bin := sysupgrade-tar | append-metadata
endef
+define Device/DniImage
+ KERNEL_SUFFIX := -fit-uImage.itb
+ KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
+ KERNEL_NAME := Image
+ NETGEAR_BOARD_ID :=
+ NETGEAR_HW_ID :=
+ IMAGES := factory.img sysupgrade.bin
+ IMAGE/factory.img := append-kernel | pad-offset 64k 64 | append-uImage-fakeroot-hdr | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | netgear-dni
+ IMAGE/sysupgrade.bin := append-kernel | pad-offset 64k 64 | append-uImage-fakeroot-hdr | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | append-metadata
+endef
+DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
+
define Device/8dev_jalapeno
$(call Device/FitImage)
@@ -113,6 +125,29 @@ define Device/meraki_mr33
endef
TARGET_DEVICES += meraki_mr33
+define Device/netgear_ex61x0v2
+ $(call Device/DniImage)
+ KERNEL_SIZE := 3080192
+ DEVICE_DTS_CONFIG := config at 4
+ DEVICE_PACKAGES := ath10k-firmware-qca4019 ipq-wifi-netgear_ex61x0v2
+ NETGEAR_BOARD_ID := EX6150v2series
+ NETGEAR_HW_ID := 29765285+16+0+128+2x2
+endef
+
+define Device/netgear_ex6100v2
+ $(call Device/netgear_ex61x0v2)
+ DEVICE_DTS := qcom-ipq4018-ex6100v2
+ DEVICE_TITLE := Netgear EX6100v2
+endef
+TARGET_DEVICES += netgear_ex6100v2
+
+define Device/netgear_ex6150v2
+ $(call Device/netgear_ex61x0v2)
+ DEVICE_DTS := qcom-ipq4018-ex6150v2
+ DEVICE_TITLE := Netgear EX6150v2
+endef
+TARGET_DEVICES += netgear_ex6150v2
+
define Device/openmesh_a42
$(call Device/FitImageLzma)
DEVICE_DTS := qcom-ipq4018-a42
diff --git a/target/linux/ipq40xx/patches-4.14/069-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.14/069-arm-boot-add-dts-files.patch
index 9c09c1f..99417d3 100644
--- a/target/linux/ipq40xx/patches-4.14/069-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-4.14/069-arm-boot-add-dts-files.patch
@@ -10,11 +10,13 @@ Signed-off-by: John Crispin <john at phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -697,7 +697,15 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -697,7 +697,17 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
+ qcom-ipq4018-a42.dtb \
++ qcom-ipq4018-ex6100v2.dtb \
++ qcom-ipq4018-ex6150v2.dtb \
+ qcom-ipq4018-fritz4040.dtb \
+ qcom-ipq4018-jalapeno.dtb \
+ qcom-ipq4018-rt-ac58u.dtb \
More information about the lede-commits
mailing list