[openwrt/openwrt] ipq40xx: add support for 8devices Jalapeno
LEDE Commits
lede-commits at lists.infradead.org
Thu Apr 12 22:54:39 PDT 2018
mkresin pushed a commit to openwrt/openwrt.git, branch master:
https://git.lede-project.org/1e341bb5ef9ba342a56ad2765c2876091fdc66db
commit 1e341bb5ef9ba342a56ad2765c2876091fdc66db
Author: Robert Marko <robimarko at gmail.com>
AuthorDate: Wed Apr 11 11:14:36 2018 +0200
ipq40xx: add support for 8devices Jalapeno
This patch adds support for 8devices Jalapeno.
Specification:
QCA IPQ4018, Quad core ARM v7 Cortex A7 717MHz
256 MB of DDR3 RAM
8 MB of SPI NOR flash
128 MB of Winbond SPI NAND flash
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
requires special BDF in QCA4019/hw1.0/board-2.bin with:
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=8devices-Jalapeno
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
requires special BDF in QCA4019/hw1.0/board-2.bin with:
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=8devices-Jalapeno
ETH: Qualcomm Atheros QCA8072 Gigabit Switch (1 x LAN, 1 x WAN)
phy at mdio3:
Label: eth0
gmac0
phy at mdio4:
Label: eth1
gmac1
Installation instructions:
Since boards ship with old version of LEDE installation is simple.
Just use sysupgrade -n -F sysupgrade.bin
Syuspgrade needs to be forced since OpenWRT uses DT detection in recent
releases.
If you get error that FIT configuration is not found during boot it is
due to older U-boot used on your board.
That is because 8devices used custom FIT configuration partition name
as they internally had v1 and v2 boards.
Only v2 boards are sold so now they are shipping boards with never
U-boot using generic config at 1 FIT partition name.
Also for old uboot it is possible to force loading config at 1 by changing
uboot environment:
setenv boot5 'bootm 0x84000000#config at 1’
saveenv
Signed-off-by: Robert Marko <robimarko at gmail.com>
---
.../ipq40xx/base-files/etc/board.d/02_network | 3 +
.../etc/hotplug.d/firmware/11-ath10k-caldata | 18 +-
.../ipq40xx/base-files/lib/upgrade/platform.sh | 3 +
.../arch/arm/boot/dts/qcom-ipq4018-jalapeno.dts | 288 +++++++++++++++++++++
target/linux/ipq40xx/image/Makefile | 11 +
.../patches-4.14/069-arm-boot-add-dts-files.patch | 3 +-
6 files changed, 317 insertions(+), 9 deletions(-)
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index a53e286..91343cd 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -12,6 +12,9 @@ board_config_update
board=$(board_name)
case "$board" in
+8dev,jalapeno)
+ ucidef_set_interfaces_lan_wan "eth0" "eth1"
+ ;;
asus,rt-ac58u)
CI_UBIPART=UBI_DEV
wan_mac_addr=$(mtd_get_mac_binary_ubi Factory 20486)
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 969983e..56c10cb 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -112,6 +112,11 @@ case "$FIRMWARE" in
;;
"ath10k/pre-cal-ahb-a000000.wifi.bin")
case "$board" in
+ 8dev,jalapeno |\
+ glinet,gl-b1300 |\
+ qcom,ap-dk01.1-c1)
+ ath10kcal_extract "ART" 4096 12064
+ ;;
asus,rt-ac58u)
CI_UBIPART=UBI_DEV
ath10kcal_ubi_extract "Factory" 4096 12064
@@ -119,10 +124,6 @@ case "$FIRMWARE" in
avm,fritzbox-4040)
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
;;
- glinet,gl-b1300 |\
- qcom,ap-dk01.1-c1)
- ath10kcal_extract "ART" 4096 12064
- ;;
meraki,mr33)
ath10kcal_ubi_extract "ART" 4096 12064
ath10kcal_is_caldata_valid "202f" || ath10kcal_extract "ART" 4096 12064
@@ -136,6 +137,11 @@ case "$FIRMWARE" in
;;
"ath10k/pre-cal-ahb-a800000.wifi.bin")
case "$board" in
+ 8dev,jalapeno |\
+ glinet,gl-b1300 |\
+ qcom,ap-dk01.1-c1)
+ ath10kcal_extract "ART" 20480 12064
+ ;;
asus,rt-ac58u)
CI_UBIPART=UBI_DEV
ath10kcal_ubi_extract "Factory" 20480 12064
@@ -143,10 +149,6 @@ case "$FIRMWARE" in
avm,fritzbox-4040)
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
;;
- glinet,gl-b1300 |\
- qcom,ap-dk01.1-c1)
- ath10kcal_extract "ART" 20480 12064
- ;;
meraki,mr33)
ath10kcal_ubi_extract "ART" 20480 12064
ath10kcal_is_caldata_valid "202f" || ath10kcal_extract "ART" 20480 12064
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
index 52aa232..5493c47 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
@@ -31,6 +31,9 @@ EOF
platform_do_upgrade() {
case "$(board_name)" in
+ 8dev,jalapeno)
+ nand_do_upgrade "$ARGV"
+ ;;
asus,rt-ac58u)
CI_UBIPART="UBI_DEV"
CI_KERNPART="linux"
diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-jalapeno.dts b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-jalapeno.dts
new file mode 100644
index 0000000..7e2bdcc
--- /dev/null
+++ b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-jalapeno.dts
@@ -0,0 +1,288 @@
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2018, Robert Marko <robimarko at gmail.com>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include "qcom-ipq4019.dtsi"
+#include "qcom-ipq4019-bus.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "8devices Jalapeno";
+ compatible = "8dev,jalapeno", "qcom,ipq4019";
+
+ reserved-memory {
+ #address-cells = <0x1>;
+ #size-cells = <0x1>;
+ ranges;
+
+ tz_apps at 87b80000 {
+ reg = <0x87b80000 0x280000>;
+ no-map;
+ };
+
+ smem at 87e00000 {
+ reg = <0x87e00000 0x080000>;
+ no-map;
+ };
+
+ tz at 87e80000 {
+ reg = <0x87e80000 0x180000>;
+ no-map;
+ };
+ };
+
+ soc {
+ mdio at 90000 {
+ status = "okay";
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+ };
+
+ ess-psgmii at 98000 {
+ status = "okay";
+ };
+
+ counter at 4a1000 {
+ compatible = "qcom,qca-gcnt";
+ reg = <0x4a1000 0x4>;
+ };
+
+ tcsr at 1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr at 194b000 {
+ /* select hostmode */
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ status = "okay";
+ };
+
+ ess_tcsr at 1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr at 1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ usb2: usb2 at 60f8800 {
+ status = "okay";
+ };
+
+ serial at 78af000 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ usb3: usb3 at 8af8800 {
+ status = "okay";
+ };
+
+ crypto at 8e3a000 {
+ status = "okay";
+ };
+
+ watchdog at b017000 {
+ status = "okay";
+ };
+
+ ess-switch at c000000 {
+ status = "okay";
+ switch_lan_bmp = <0x10>; /* lan port bitmap */
+ };
+
+ edma at c080000 {
+ status = "okay";
+ };
+ };
+};
+
+&tlmm {
+ mdio_pins: mdio_pinmux {
+ pinmux_1 {
+ pins = "gpio53";
+ function = "mdio";
+ };
+ pinmux_2 {
+ pins = "gpio52";
+ function = "mdc";
+ };
+ pinconf {
+ pins = "gpio52", "gpio53";
+ bias-pull-up;
+ };
+ };
+
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pin {
+ function = "blsp_spi0";
+ pins = "gpio55", "gpio56", "gpio57";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ pin_cs {
+ function = "gpio";
+ pins = "gpio54", "gpio59";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&spi_0 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, <&tlmm 59 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ m25p80 at 0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition0 at 0 {
+ label = "SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+ partition1 at 40000 {
+ label = "MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+ partition2 at 60000 {
+ label = "QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+ partition3 at c0000 {
+ label = "CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+ partition4 at d0000 {
+ label = "DDRPARAMS";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+ partition5 at e0000 {
+ label = "APPSBLENV"; /* uboot env*/
+ reg = <0x000e0000 0x00010000>;
+ read-only;
+ };
+ partition5 at f0000 {
+ label = "APPSBL"; /* uboot */
+ reg = <0x000f0000 0x00080000>;
+ read-only;
+ };
+ partition5 at 170000 {
+ label = "ART";
+ reg = <0x00170000 0x00010000>;
+ read-only;
+ };
+ };
+ };
+
+ mt29f at 1 {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "spinand,mt29f", "w25n01gv";
+ reg = <1>;
+ spi-max-frequency = <24000000>;
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition0 at 0 {
+ label = "ubi";
+ reg = <0x00000000 0x08000000>;
+ };
+ };
+ };
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&gmac0 {
+ qcom,poll_required = <1>;
+ qcom,poll_required_dynamic = <1>;
+ qcom,phy_mdio_addr = <3>;
+ vlan_tag = <1 0x10>;
+};
+
+&gmac1 {
+ qcom,poll_required = <1>;
+ qcom,poll_required_dynamic = <1>;
+ qcom,phy_mdio_addr = <4>;
+ vlan_tag = <2 0x20>;
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "8devices-Jalapeno";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "8devices-Jalapeno";
+};
+
+&usb3_ss_phy {
+ status = "okay";
+};
+
+&usb3_hs_phy {
+ status = "okay";
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile
index 125b3bf..e3364c4 100644
--- a/target/linux/ipq40xx/image/Makefile
+++ b/target/linux/ipq40xx/image/Makefile
@@ -32,6 +32,17 @@ define Device/UbiFit
endef
+define Device/8dev_jalapeno
+ $(call Device/FitImage)
+ $(call Device/UbiFit)
+ DEVICE_DTS := qcom-ipq4018-jalapeno
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ DEVICE_TITLE := 8devices Jalapeno
+ DEVICE_PACKAGES := ath10k-firmware-qca4019
+endef
+TARGET_DEVICES += 8dev_jalapeno
+
define Device/asus_rt-ac58u
$(call Device/FitImageLzma)
DEVICE_DTS := qcom-ipq4018-rt-ac58u
diff --git a/target/linux/ipq40xx/patches-4.14/069-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.14/069-arm-boot-add-dts-files.patch
index c0bdd87..9c09c1f 100644
--- a/target/linux/ipq40xx/patches-4.14/069-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-4.14/069-arm-boot-add-dts-files.patch
@@ -10,12 +10,13 @@ Signed-off-by: John Crispin <john at phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -697,7 +697,14 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -697,7 +697,15 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
+ qcom-ipq4018-a42.dtb \
+ qcom-ipq4018-fritz4040.dtb \
++ qcom-ipq4018-jalapeno.dtb \
+ qcom-ipq4018-rt-ac58u.dtb \
qcom-ipq4019-ap.dk01.1-c1.dtb \
+ qcom-ipq4019-ap.dk04.1-c1.dtb \
More information about the lede-commits
mailing list