[source] ramips: fix Youku-YK1 support

[LEDE Commits]

mkresin pushed a commit to source.git, branch master:
https://git.lede-project.org/9786b53efb8225f5b6f21921e684b40b9febe61e

commit 9786b53efb8225f5b6f21921e684b40b9febe61e
Author: Edmunt Pienkowsky <roed at onet.eu>
AuthorDate: Sat Oct 21 11:07:43 2017 +0200

    ramips: fix Youku-YK1 support
    
    Remove the ephy-pins from the ethernet device tree node. The ephy-pins
    are useed to controll the ePHY LEDs and this board doesn't have these.
    Instead one of the ePHY pins is used in GPIO mode to control the WAN
    LED.
    
    Use the switch LED trigger to control the WAN LED. Move the power LED
    handling to diag.sh to show the boot status via this LED.
    
    Add the missing kernel packages for USB and microSD card reader to the
    default package selection.
    
    Fix the maximum image size value. The board has a 32MByte flash chip.
    
    Fixes: FS#1055
    
    Signed-off-by: Edmunt Pienkowsky <roed at onet.eu>
    [make the commit message more verbose, remove GPIO pinmux for pins not
    used as GPIOs]
    Signed-off-by: Mathias Kresin <dev at kresin.me>
---
 target/linux/ramips/base-files/etc/board.d/01_leds | 2 +-
 target/linux/ramips/base-files/etc/diag.sh         | 3 ++-
 target/linux/ramips/dts/YOUKU-YK1.dts              | 3 +--
 target/linux/ramips/image/mt7620.mk                | 3 ++-
 4 files changed, 6 insertions(+), 5 deletions(-)

diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
index 75ab0da..037331d 100755
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -461,9 +461,9 @@ zte-q7)
 	set_wifi_led "$board:blue:status"
 	;;
 youku-yk1)
-	ucidef_set_led_default "power" "power" "$board:blue:power" "1"
 	set_wifi_led "$board:blue:air"
 	set_usb_led "$board:blue:usb"
+	ucidef_set_led_switch "wan" "wan" "$board:blue:wan" "switch0" "0x10"
 	;;
 esac
 
diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
index 4411bab..3b3c455 100644
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -134,7 +134,8 @@ get_status_led() {
 	wl-330n3g|\
 	wli-tx4-ag300n|\
 	y1|\
-	y1s)
+	y1s|\
+	youku-yk1)
 		status_led="$board:blue:power"
 		;;
 	db-wrt01|\
diff --git a/target/linux/ramips/dts/YOUKU-YK1.dts b/target/linux/ramips/dts/YOUKU-YK1.dts
index d4e3c90..8a0e081 100644
--- a/target/linux/ramips/dts/YOUKU-YK1.dts
+++ b/target/linux/ramips/dts/YOUKU-YK1.dts
@@ -96,7 +96,7 @@
 &pinctrl {
 	state_default: pinctrl0 {
 		default {
-			ralink,group = "i2c", "uartf", "rgmii1", "rgmii2", "ephy", "wled", "nd_sd";
+			ralink,group = "i2c", "rgmii1", "ephy", "wled";
 			ralink,function = "gpio";
 		};
 	};
@@ -104,7 +104,6 @@
 
 &ethernet {
 	pinctrl-names = "default";
-	pinctrl-0 = <&ephy_pins>;
 	mtd-mac-address = <&factory 0x4>;
 	mediatek,portmap = "llllw";
 };
diff --git a/target/linux/ramips/image/mt7620.mk b/target/linux/ramips/image/mt7620.mk
index 8eac6f5..2f3f59e 100644
--- a/target/linux/ramips/image/mt7620.mk
+++ b/target/linux/ramips/image/mt7620.mk
@@ -505,8 +505,9 @@ TARGET_DEVICES += y1s
 
 define Device/youku-yk1
   DTS := YOUKU-YK1
-  IMAGE_SIZE := $(ralink_default_fw_size_16M)
+  IMAGE_SIZE := $(ralink_default_fw_size_32M)
   DEVICE_TITLE := YOUKU YK1
+  DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-sdhci-mt7620 kmod-usb-ledtrig-usbport
 endef
 TARGET_DEVICES += youku-yk1