[source] ar71xx: Compex WPJ563 support
LEDE Commits
lede-commits at lists.infradead.org
Thu Mar 30 01:01:29 PDT 2017
blogic pushed a commit to source.git, branch master:
https://git.lede-project.org/dc4eae7a8cf676911b0048b1e73c6f9adeea2f06
commit dc4eae7a8cf676911b0048b1e73c6f9adeea2f06
Author: Christian Mehlis <christian at m3hlis.de>
AuthorDate: Sun Feb 26 12:25:57 2017 +0100
ar71xx: Compex WPJ563 support
Specification:
- SoC: Qualcomm Atheros QCA9563 (775 MHz, MIPS 74Kc)
- RAM: 128 MiB
- Storage: 16MB NOR flash
- Wireless: Built into QCA9563 (Dragonfly), PHY modes b/g/n, 3x3 MIMO
- Ethernet: 2x1G
Tested and working:
- ethernet / switch / lan / wan
- 2.4GHz SoC wifi
- PCIe
- leds
- buzzer
Ramload:
- tftpboot 0x84000000 lede-ar71xx-generic-wpj563-16M-initramfs-uImage.bin
- bootm 0x84000000
Install:
- tftpboot 0x80500000 lede-ar71xx-generic-wpj563-16M-squashfs-sysupgrade.bin
- erase 0x9f030000 +$filesize
- erase 0x9f680000 +1
- cp.b $fileaddr 0x9f030000 $filesize
Erasing 0x9f680000 is required because uboot defines
"bootcmd=bootm 0x9f680000 || bootm 0x9f030000", so it first tries to boot
the higher address. I think the 16 mb flash are intended to be used as
8+8mb for a fallback image. In my hardware only the lower address has a
bootable image. But to make sure future hardware will boot lede too, I
erase one block, so uboot will skip this address.
Signed-off-by: Christian Mehlis <christian at m3hlis.de>
---
.../linux/ar71xx/base-files/etc/board.d/02_network | 4 +
target/linux/ar71xx/base-files/etc/diag.sh | 3 +
target/linux/ar71xx/base-files/lib/ar71xx.sh | 3 +
.../ar71xx/base-files/lib/upgrade/platform.sh | 1 +
target/linux/ar71xx/config-4.4 | 1 +
.../ar71xx/files/arch/mips/ath79/Kconfig.openwrt | 11 ++
target/linux/ar71xx/files/arch/mips/ath79/Makefile | 1 +
.../ar71xx/files/arch/mips/ath79/mach-wpj563.c | 150 +++++++++++++++++++++
.../linux/ar71xx/files/arch/mips/ath79/machtypes.h | 1 +
target/linux/ar71xx/image/generic.mk | 9 ++
target/linux/ar71xx/mikrotik/config-default | 1 +
target/linux/ar71xx/nand/config-default | 1 +
12 files changed, 186 insertions(+)
diff --git a/target/linux/ar71xx/base-files/etc/board.d/02_network b/target/linux/ar71xx/base-files/etc/board.d/02_network
index e5892ac..bf7c4dc 100755
--- a/target/linux/ar71xx/base-files/etc/board.d/02_network
+++ b/target/linux/ar71xx/base-files/etc/board.d/02_network
@@ -466,6 +466,10 @@ ar71xx_setup_interfaces()
ucidef_add_switch "switch0" \
"5:lan" "1:wan" "6 at eth0"
;;
+ wpj563)
+ ucidef_add_switch "switch0" \
+ "0 at eth0" "2:lan" "3:wan"
+ ;;
wrt160nl)
ucidef_set_interfaces_lan_wan "eth0.1" "eth1"
ucidef_add_switch "switch0" \
diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh
index fed51a1..3cde175 100644
--- a/target/linux/ar71xx/base-files/etc/diag.sh
+++ b/target/linux/ar71xx/base-files/etc/diag.sh
@@ -469,6 +469,9 @@ get_status_led() {
wpj558)
status_led="$board:green:sig3"
;;
+ wpj563)
+ status_led="$board:green:sig1"
+ ;;
wrt400n|\
wrt160nl)
status_led="$board:blue:wps"
diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh
index eedcb78..25f6b01 100755
--- a/target/linux/ar71xx/base-files/lib/ar71xx.sh
+++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh
@@ -1240,6 +1240,9 @@ ar71xx_board_detect() {
*"WPJ558")
name="wpj558"
;;
+ *"WPJ563")
+ name="wpj563"
+ ;;
*"WPN824N")
name="wpn824n"
;;
diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
index 2f0228b..fb58209 100755
--- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
@@ -283,6 +283,7 @@ platform_check_image() {
wpj342|\
wpj344|\
wpj531|\
+ wpj563|\
wrt400n|\
wrtnode2q|\
wzr-450hp2|\
diff --git a/target/linux/ar71xx/config-4.4 b/target/linux/ar71xx/config-4.4
index 386ce68..6d0941b 100644
--- a/target/linux/ar71xx/config-4.4
+++ b/target/linux/ar71xx/config-4.4
@@ -226,6 +226,7 @@ CONFIG_ATH79_MACH_WPJ342=y
CONFIG_ATH79_MACH_WPJ344=y
CONFIG_ATH79_MACH_WPJ531=y
CONFIG_ATH79_MACH_WPJ558=y
+CONFIG_ATH79_MACH_WPJ563=y
CONFIG_ATH79_MACH_WRT160NL=y
CONFIG_ATH79_MACH_WRT400N=y
CONFIG_ATH79_MACH_WRTNODE2Q=y
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
index 669e026..183e91a 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
+++ b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
@@ -459,6 +459,17 @@ config ATH79_MACH_WPJ558
select ATH79_DEV_USB
select ATH79_DEV_WMAC
+config ATH79_MACH_WPJ563
+ bool "Compex WPJ563 board support"
+ select SOC_QCA956X
+ select ATH79_DEV_AP9X_PCI if PCI
+ select ATH79_DEV_ETH
+ select ATH79_DEV_GPIO_BUTTONS
+ select ATH79_DEV_LEDS_GPIO
+ select ATH79_DEV_M25P80
+ select ATH79_DEV_USB
+ select ATH79_DEV_WMAC
+
config ATH79_MACH_XD3200
bool "YunCore XD3200 support"
select SOC_QCA956X
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Makefile b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
index 1180d4d..01ec133 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/Makefile
+++ b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
@@ -231,6 +231,7 @@ obj-$(CONFIG_ATH79_MACH_WPJ342) += mach-wpj342.o
obj-$(CONFIG_ATH79_MACH_WPJ344) += mach-wpj344.o
obj-$(CONFIG_ATH79_MACH_WPJ531) += mach-wpj531.o
obj-$(CONFIG_ATH79_MACH_WPJ558) += mach-wpj558.o
+obj-$(CONFIG_ATH79_MACH_WPJ563) += mach-wpj563.o
obj-$(CONFIG_ATH79_MACH_WRT160NL) += mach-wrt160nl.o
obj-$(CONFIG_ATH79_MACH_WRT400N) += mach-wrt400n.o
obj-$(CONFIG_ATH79_MACH_WRTNODE2Q) += mach-wrtnode2q.o
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-wpj563.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-wpj563.c
new file mode 100644
index 0000000..70593d8
--- /dev/null
+++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-wpj563.c
@@ -0,0 +1,150 @@
+/*
+ * Compex WPJ563 board support
+ *
+ * Copyright (c) 2015 Qualcomm Atheros
+ * Copyright (c) 2012 Gabor Juhos <juhosg at openwrt.org>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include <linux/platform_device.h>
+#include <linux/ath9k_platform.h>
+#include <linux/ar8216_platform.h>
+#include <asm/mach-ath79/ar71xx_regs.h>
+
+#include "common.h"
+#include "dev-m25p80.h"
+#include "machtypes.h"
+#include "pci.h"
+#include "dev-eth.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-spi.h"
+#include "dev-usb.h"
+#include "dev-wmac.h"
+
+#define WPJ563_GPIO_LED_SIG1 1
+#define WPJ563_GPIO_LED_SIG2 5
+#define WPJ563_GPIO_LED_SIG3 6
+#define WPJ563_GPIO_LED_SIG4 7
+#define WPJ563_GPIO_BUZZER 19
+
+#define WPJ563_GPIO_BTN_RESET 2
+#define WPJ563_KEYS_POLL_INTERVAL 20 /* msecs */
+#define WPJ563_KEYS_DEBOUNCE_INTERVAL (3 * WPJ563_KEYS_POLL_INTERVAL)
+
+#define WPJ563_MAC0_OFFSET 0x10
+#define WPJ563_MAC1_OFFSET 0x18
+#define WPJ563_WMAC_CALDATA_OFFSET 0x1000
+
+static struct gpio_led WPJ563_leds_gpio[] __initdata = {
+ {
+ .name = "wpj563:green:sig1",
+ .gpio = WPJ563_GPIO_LED_SIG1,
+ .active_low = 1,
+ },
+ {
+ .name = "wpj563:green:sig2",
+ .gpio = WPJ563_GPIO_LED_SIG2,
+ .active_low = 1,
+ },
+ {
+ .name = "wpj563:green:sig3",
+ .gpio = WPJ563_GPIO_LED_SIG3,
+ .active_low = 1,
+ },
+ {
+ .name = "wpj563:green:sig4",
+ .gpio = WPJ563_GPIO_LED_SIG4,
+ .active_low = 1,
+ },
+ {
+ .name = "wpj563:buzzer",
+ .gpio = WPJ563_GPIO_BUZZER,
+ .active_low = 0,
+ }
+};
+
+static struct gpio_keys_button WPJ563_gpio_keys[] __initdata = {
+ {
+ .desc = "Reset button",
+ .type = EV_KEY,
+ .code = KEY_RESTART,
+ .debounce_interval = WPJ563_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = WPJ563_GPIO_BTN_RESET,
+ .active_low = 1,
+ },
+};
+
+static struct ar8327_pad_cfg WPJ563_ar8337_pad0_cfg = {
+ .mode = AR8327_PAD_MAC_SGMII,
+ .sgmii_delay_en = true,
+};
+
+static struct ar8327_platform_data WPJ563_ar8337_data = {
+ .pad0_cfg = &WPJ563_ar8337_pad0_cfg,
+ .port0_cfg = {
+ .force_link = 1,
+ .speed = AR8327_PORT_SPEED_1000,
+ .duplex = 1,
+ .txpause = 1,
+ .rxpause = 1,
+ },
+};
+
+static struct mdio_board_info WPJ563_mdio0_info[] = {
+ {
+ .bus_id = "ag71xx-mdio.0",
+ .phy_addr = 0,
+ .platform_data = &WPJ563_ar8337_data,
+ },
+};
+
+static void __init WPJ563_setup(void)
+{
+ u8 *art = (u8 *) KSEG1ADDR(0x1fff0000);
+ u8 *mac = (u8 *) KSEG1ADDR(0x1f02e000);
+
+ ath79_register_m25p80(NULL);
+
+ ath79_register_leds_gpio(-1, ARRAY_SIZE(WPJ563_leds_gpio),
+ WPJ563_leds_gpio);
+ ath79_register_gpio_keys_polled(-1, WPJ563_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(WPJ563_gpio_keys),
+ WPJ563_gpio_keys);
+
+ ath79_register_usb();
+
+ ath79_register_wmac(art + WPJ563_WMAC_CALDATA_OFFSET, NULL);
+
+ ath79_register_pci();
+
+ mdiobus_register_board_info(WPJ563_mdio0_info,
+ ARRAY_SIZE(WPJ563_mdio0_info));
+ ath79_register_mdio(0, 0x0);
+
+ ath79_init_mac(ath79_eth0_data.mac_addr, mac + WPJ563_MAC0_OFFSET, 0);
+ ath79_init_mac(ath79_eth1_data.mac_addr, mac + WPJ563_MAC1_OFFSET, 0);
+
+ /* GMAC0 is connected to an QCA8334 switch */
+ ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_SGMII;
+ ath79_eth0_data.speed = SPEED_1000;
+ ath79_eth0_data.duplex = DUPLEX_FULL;
+ ath79_eth0_data.phy_mask = BIT(0);
+ ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
+
+ ath79_register_eth(0);
+}
+
+MIPS_MACHINE(ATH79_MACH_WPJ563, "WPJ563", "Compex WPJ563", WPJ563_setup);
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
index b9cc243..4278f5e 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
+++ b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
@@ -303,6 +303,7 @@ enum ath79_mach_type {
ATH79_MACH_WPJ344, /* Compex WPJ344 */
ATH79_MACH_WPJ531, /* Compex WPJ531 */
ATH79_MACH_WPJ558, /* Compex WPJ558 */
+ ATH79_MACH_WPJ563, /* Compex WPJ563 */
ATH79_MACH_WPN824N, /* NETGEAR WPN824N */
ATH79_MACH_WRT160NL, /* Linksys WRT160NL */
ATH79_MACH_WRT400N, /* Linksys WRT400N */
diff --git a/target/linux/ar71xx/image/generic.mk b/target/linux/ar71xx/image/generic.mk
index 2ad058e..ebcb183 100644
--- a/target/linux/ar71xx/image/generic.mk
+++ b/target/linux/ar71xx/image/generic.mk
@@ -825,3 +825,12 @@ define Device/wpj558
IMAGE_SIZE := 16128k
endef
TARGET_DEVICES += wpj558
+
+define Device/wpj563
+ DEVICE_TITLE := Compex WPJ563 (16MB flash)
+ DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport
+ BOARDNAME := WPJ563
+ MTDPARTS := spi0.0:192k(u-boot)ro,16128k(firmware),64k(art)ro
+ IMAGE_SIZE := 16128k
+endef
+TARGET_DEVICES += wpj563
diff --git a/target/linux/ar71xx/mikrotik/config-default b/target/linux/ar71xx/mikrotik/config-default
index 1cc485a..ecaa6e5 100644
--- a/target/linux/ar71xx/mikrotik/config-default
+++ b/target/linux/ar71xx/mikrotik/config-default
@@ -191,6 +191,7 @@ CONFIG_ATH79_MACH_RBSXTLITE=y
# CONFIG_ATH79_MACH_WPJ344 is not set
# CONFIG_ATH79_MACH_WPJ531 is not set
# CONFIG_ATH79_MACH_WPJ558 is not set
+# CONFIG_ATH79_MACH_WPJ563 is not set
# CONFIG_ATH79_MACH_WRT160NL is not set
# CONFIG_ATH79_MACH_WRT400N is not set
# CONFIG_ATH79_MACH_WRTNODE2Q is not set
diff --git a/target/linux/ar71xx/nand/config-default b/target/linux/ar71xx/nand/config-default
index 16e652e..1c5d0ba 100644
--- a/target/linux/ar71xx/nand/config-default
+++ b/target/linux/ar71xx/nand/config-default
@@ -176,6 +176,7 @@
# CONFIG_ATH79_MACH_WPJ344 is not set
# CONFIG_ATH79_MACH_WPJ531 is not set
# CONFIG_ATH79_MACH_WPJ558 is not set
+# CONFIG_ATH79_MACH_WPJ563 is not set
# CONFIG_ATH79_MACH_WRT160NL is not set
# CONFIG_ATH79_MACH_WRT400N is not set
# CONFIG_ATH79_MACH_WRTNODE2Q is not set
More information about the lede-commits
mailing list