[source] ipq806x: add ipq4019 fritz4040 support

LEDE Commits lede-commits at lists.infradead.org
Wed Mar 22 01:45:43 PDT 2017 

blogic pushed a commit to source.git, branch master:
https://git.lede-project.org/1cb406d019dc84497a8405c470f0b0394d5ff64a

commit 1cb406d019dc84497a8405c470f0b0394d5ff64a
Author: Christian Lamparter <chunkeey at googlemail.com>
AuthorDate: Tue Mar 14 17:04:28 2017 +0100

    ipq806x: add ipq4019 fritz4040 support
    
    This patch adds support for AVM FRITZ!Box 4040.
    
    hardware highlights:
    
    SOC:	IPQ4018 / QCA Dakota
    CPU:	Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
    DRAM:	256 MiB Nanya NT5CC128M16IP
    FLASH:	32 MiB MXIC MX25L25635FMI
    ETH:	Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
    USB:	1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
    	1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC)
    WLAN1:	Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
    WLAN2:	Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
    INPUT:	one WLAN and one WPS button
    LEDS:	Power, WAN/Internet, WIFI, INFO (red and amber) and LAN.
    Serial:
    	WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
            The Serial setting is 115200-8-N-1. The SoC's serial port is right
    	next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1"
    	header for it. Use a multimeter to figure out the pinout!
    
    This board currently needs an additional u-boot image in order to boot
    properly. Booting with EVA isn't possible ATM.
    
    Install Procedure:
     0. It's highly recommended to connect to the serial port.
        The serial settings are listed above.
     1. install a u-boot image for AVM Fritz!Box 4040
        (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and
        <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>)
     2. upload the initramfs.itb image via tftp (u-boot listens to
        192.168.1.1 - use binary transfer mode!)
     3. connect to the FB4040 and use sysupgrade sysupgrade.bin
        to install the image.
    
    Works:
    	- Switch and Ethernet (99%)
            - Buttons (WLAN, WPS)
            - FLASH (1 x 32MiB NOR Chip)
            - WLAN2G and WLAN5G
            - CPUFREQ scaling
            - PRNG
            - serial
            - Crypto Accelerator
            - sysupgrade (Read the flash instructions to avoid bricking)
            - full LEDE Install (Read the flash instructions to avoid bricking)
    	- LEDs (Power, WAN, Info (red and amber), LAN)
              The LEDs are connected to the QCA8075 LED ports.
    	  The AR40xx driver contains a gpio-controller to
    	  handle these special "GPIOs".
            - USB Both 3.0 and 2.0 ports
            - many packages from other ARMv7 boards
              (This does include the RaspberryPi Model 2!)
            - ...
    
    Not planned:
    	- WAN<->LAN short-cut
    	- Qualcomm Secure Execution Environment
            - ...
    
    Signed-off-by: Christian Lamparter <chunkeey at googlemail.com>
    Signed-off-by: John Crispin <john at phrozen.org>
---
 .../linux/ipq806x/base-files/etc/board.d/01_leds   |  5 +++++
 .../ipq806x/base-files/etc/board.d/02_network      |  5 +++++
 .../etc/hotplug.d/firmware/11-ath10k-caldata       | 15 +++++++++++++
 target/linux/ipq806x/base-files/lib/ipq806x.sh     |  3 +++
 .../ipq806x/base-files/lib/upgrade/platform.sh     |  3 +++
 .../arch/arm/boot/dts/qcom-ipq4019-fritz4040.dts   |  2 +-
 target/linux/ipq806x/image/Makefile                | 26 +++++++++++++++++++---
 7 files changed, 55 insertions(+), 4 deletions(-)

diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds
index 977b3b1..1371767 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds
@@ -26,6 +26,11 @@ r7800)
 	ucidef_set_led_netdev "wan" "WAN" "${board}:white:wan" "eth0"
 	ucidef_set_led_ide "esata" "eSATA" "${board}:white:esata"
 	;;
+fritz4040)
+	ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt" "phy1tpt"
+	ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth1"
+	ucidef_set_led_switch "lan" "LAN" "${board}:green:lan" "switch0" "0x1e"
+	;;
 nbg6817)
 	ucidef_set_led_wlan "wlan2g" "WLAN2G" "$board:amber:wifi2g" "phy1tpt"
 	ucidef_set_led_wlan "wlan5g" "WLAN5G" "$board:amber:wifi5g" "phy0tpt"
diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network
index 52bb162..36e0fb3 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/02_network
+++ b/target/linux/ipq806x/base-files/etc/board.d/02_network
@@ -36,6 +36,11 @@ ea8500)
 	ucidef_set_interface_macaddr "lan" "$hw_mac_addr"
 	ucidef_set_interface_macaddr "wan" "$hw_mac_addr"
 	;;
+fritz4040)
+	ucidef_set_interfaces_lan_wan "eth0" "eth1"
+	ucidef_add_switch "switch0" \
+		"0 at eth0" "1:lan" "2:lan" "3:lan" "4:lan"
+	;;
 nbg6817)
 	hw_mac_addr=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr)
 	ucidef_add_switch "switch0" \
diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 72c3ae8..6526212 100644
--- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -46,6 +46,21 @@ board=$(ipq806x_board_name)
 
 
 case "$FIRMWARE" in
+"ath10k/pre-cal-ahb-a000000.wifi.bin")
+	case "$board" in
+	fritz4040)
+		/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
+		;;
+	esac
+	;;
+"ath10k/pre-cal-ahb-a800000.wifi.bin")
+	case "$board" in
+	fritz4040)
+		/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
+		;;
+	esac
+	;;
+
 "ath10k/cal-pci-0000:01:00.0.bin")
 	case $board in
 	c2600)
diff --git a/target/linux/ipq806x/base-files/lib/ipq806x.sh b/target/linux/ipq806x/base-files/lib/ipq806x.sh
index a8b909a..348a3a8 100644
--- a/target/linux/ipq806x/base-files/lib/ipq806x.sh
+++ b/target/linux/ipq806x/base-files/lib/ipq806x.sh
@@ -17,6 +17,9 @@ ipq806x_board_detect() {
 	*"AP148")
 		name="ap148"
 		;;
+	*"4040")
+		name="fritz4040"
+		;;
 	*"C2600")
 		name="c2600"
 		;;
diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
index c3741f9..8970285 100644
--- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
@@ -42,6 +42,9 @@ platform_do_upgrade() {
 		MTD_CONFIG_ARGS="-s 0x200000"
 		default_do_upgrade "$ARGV"
 		;;
+	*)
+		default_do_upgrade "$ARGV"
+		;;
 	esac
 }
 
diff --git a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq4019-fritz4040.dts b/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq4019-fritz4040.dts
index fdd565c..1bd5b51 100644
--- a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq4019-fritz4040.dts
+++ b/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq4019-fritz4040.dts
@@ -272,7 +272,7 @@
 				read-only;
 			};
 			partition11 at 2A0000 {
-				label = "image"; /* firmware */
+				label = "firmware";
 				reg = <0x002A0000 0x01C60000>;
 			};
 			partition12 at 1f00000 {
diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile
index 70c8056..8091d99 100644
--- a/target/linux/ipq806x/image/Makefile
+++ b/target/linux/ipq806x/image/Makefile
@@ -5,8 +5,6 @@ include $(INCLUDE_DIR)/image.mk
 
 UBIFS_OPTS = -m 2048 -e 124KiB -c 4096 -U -F
 
-KERNEL_LOADADDR := 0x42208000
-
 define Image/Prepare
 	$(CP) $(LINUX_DIR)/vmlinux $(KDIR)/$(IMG_PREFIX)-vmlinux.elf
 endef
@@ -30,6 +28,7 @@ define Device/Default
 	KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
 	KERNEL_INITRAMFS_PREFIX := $$(IMG_PREFIX)-$(1)-initramfs
 	KERNEL_PREFIX := $$(IMAGE_PREFIX)
+	KERNEL_LOADADDR = 0x42208000
 	SUPPORTED_DEVICES = $$(BOARD_NAME)
 	IMAGE/sysupgrade.tar = sysupgrade-tar | append-metadata
 endef
@@ -46,6 +45,12 @@ define Device/FitImage
 	KERNEL_NAME := Image
 endef
 
+define Device/FitImageLzma
+	KERNEL_SUFFIX := -fit-uImage.itb
+	KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb
+	KERNEL_NAME := Image
+endef
+
 define Device/UbiFit
 	KERNEL_IN_UBI := 1
 	IMAGES := nand-factory.ubi nand-sysupgrade.tar
@@ -165,6 +170,20 @@ define Device/EA8500
 	DEVICE_PACKAGES := ath10k-firmware-qca99x0
 endef
 
+define Device/FRITZ4040
+	$(call Device/FitImageLzma)
+	DEVICE_DTS := qcom-ipq4019-fritz4040
+	KERNEL_LOADADDR := 0x80208000
+	BLOCKSIZE := 4k
+	PAGESIZE := 256
+	BOARD_NAME := fritz4040
+	DEVICE_TITLE := AVM Fritz!Box 4040
+	IMAGE_SIZE := 29753344
+	IMAGES = sysupgrade.bin
+	IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
+	DEVICE_PACKAGES := kmod-usb-phy-qcom-ipq4019 ipq-wifi-fritz4040 fritz-tools u-boot-fritz4040
+endef
+
 define Device/R7500
 	$(call Device/DniImage)
 	DEVICE_DTS := qcom-ipq8064-r7500
@@ -231,6 +250,7 @@ define Device/VR2600v
 	IMAGE/sysupgrade.bin := pad-extra 512 | append-kernel | pad-to $$$${KERNEL_SIZE} | append-rootfs | pad-rootfs | append-metadata
 endef
 
-TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 R7500 R7500v2 R7800 NBG6817 VR2600v
+TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 FRITZ4040 R7500 \
+		  R7500v2 R7800 NBG6817 VR2600v
 
 $(eval $(call BuildImage))

More information about the lede-commits mailing list