[source] ar71xx: add support for Rockeetech AP531B0
LEDE Commits
lede-commits at lists.infradead.org
Sun Mar 12 16:18:38 PDT 2017
pepe2k pushed a commit to source.git, branch master:
https://git.lede-project.org/53ef20f65acdcd068b1166d2522dcbe7d7e298c4
commit 53ef20f65acdcd068b1166d2522dcbe7d7e298c4
Author: Shuanglin Liu <roboidler at gmail.com>
AuthorDate: Fri Mar 3 01:23:50 2017 +0800
ar71xx: add support for Rockeetech AP531B0
Specification:
- SoC: Qualcomm Atheros QCA9531 (650/400/216 MHz (CPU/DDR/AHB))
- RAM: 64 MiB DDR2
- Storage: 16 MiB of flash (optional 16 MiB second flash)
- Wireless: built into QCA9531 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0) 1x100M (port 4)
- PCI-E: x1
- SIMcard slot: x1
- USB 2.0 port: x1 (optional)
- Ext GPIO pin: x8
- UART for serial console: x1
- External watchdog: x1 (optional)
- Power supply: 9-48V (DC jack/passive PoE)
Installation through tftp:
- Copy <Firmware Image Name> into tftp directory
- Connect board via ttl port and Ethernet port
- Boot the AP531B0
- When "Autobooting in 1 seconds" appears press Enter
- Set serverip and ipaddr appropriate
(e.g. setenv serverip 192.168.88.10;setenv ipaddr 192.168.88.1)
- Enter "tftp 0x8050000 <Firmware Image Name>"
- Enter "erase 0x9f050000 +$filesize"
- Enter "cp.b 0x80500000 0x9f050000 $filesize"
- Enter "reset"
Signed-off-by: Shuanglin Liu <roboidler at gmail.com>
---
target/linux/ar71xx/base-files/etc/board.d/01_leds | 9 +-
target/linux/ar71xx/base-files/etc/diag.sh | 1 +
target/linux/ar71xx/base-files/lib/ar71xx.sh | 3 +
.../ar71xx/base-files/lib/upgrade/platform.sh | 1 +
target/linux/ar71xx/config-4.4 | 1 +
.../ar71xx/files/arch/mips/ath79/Kconfig.openwrt | 12 +++
target/linux/ar71xx/files/arch/mips/ath79/Makefile | 1 +
.../ar71xx/files/arch/mips/ath79/mach-ap531b0.c | 112 +++++++++++++++++++++
.../linux/ar71xx/files/arch/mips/ath79/machtypes.h | 1 +
target/linux/ar71xx/image/generic.mk | 9 ++
target/linux/ar71xx/mikrotik/config-default | 1 +
target/linux/ar71xx/nand/config-default | 1 +
12 files changed, 148 insertions(+), 4 deletions(-)
diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds b/target/linux/ar71xx/base-files/etc/board.d/01_leds
index 0ed533d..32d4931 100755
--- a/target/linux/ar71xx/base-files/etc/board.d/01_leds
+++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds
@@ -49,6 +49,11 @@ antrouter-r1)
ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt"
ucidef_set_led_default "btc" "BTC" "$board:green:btc" "0"
;;
+ap531b0|\
+sc1750|\
+sc450)
+ ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt"
+ ;;
archer-c59-v1|\
archer-c60-v1)
ucidef_set_led_switch "lan" "LAN" "$board:green:lan" "switch0" "0x1E"
@@ -490,10 +495,6 @@ re450)
ucidef_set_led_wlan "wlan2g" "WLAN 2.4 GHz" "$board:blue:wlan2g" "phy1tpt"
ucidef_set_led_wlan "wlan5g" "WLAN 5 GHz" "$board:blue:wlan5g" "phy0tpt"
;;
-sc1750|\
-sc450)
- ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt"
- ;;
smart-300)
ucidef_set_led_netdev "wan" "WAN" "nc-link:green:wan" "eth0"
ucidef_set_led_switch "lan1" "LAN1" "nc-link:green:lan1" "switch0" "0x04"
diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh
index 7987e51..461d0da 100644
--- a/target/linux/ar71xx/base-files/etc/diag.sh
+++ b/target/linux/ar71xx/base-files/etc/diag.sh
@@ -31,6 +31,7 @@ get_status_led() {
status_led="$board:green:system"
;;
ap132|\
+ ap531b0|\
db120|\
dr344|\
tew-632brp|\
diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh
index ae0189d..4a0c85d 100755
--- a/target/linux/ar71xx/base-files/lib/ar71xx.sh
+++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh
@@ -458,6 +458,9 @@ ar71xx_board_detect() {
*"AP152 reference board")
name="ap152"
;;
+ *AP531B0)
+ name="ap531b0"
+ ;;
*AP90Q)
name="ap90q"
;;
diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
index 576ff6c..f89ad2c 100755
--- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
@@ -204,6 +204,7 @@ platform_check_image() {
airgateway|\
airrouter|\
ap132|\
+ ap531b0|\
ap90q|\
archer-c59-v1|\
archer-c60-v1|\
diff --git a/target/linux/ar71xx/config-4.4 b/target/linux/ar71xx/config-4.4
index 206ace6..68b408a 100644
--- a/target/linux/ar71xx/config-4.4
+++ b/target/linux/ar71xx/config-4.4
@@ -47,6 +47,7 @@ CONFIG_ATH79_MACH_AP136=y
CONFIG_ATH79_MACH_AP143=y
CONFIG_ATH79_MACH_AP147=y
CONFIG_ATH79_MACH_AP152=y
+CONFIG_ATH79_MACH_AP531B0=y
# CONFIG_ATH79_MACH_AP81 is not set
CONFIG_ATH79_MACH_AP90Q=y
CONFIG_ATH79_MACH_AP96=y
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
index 514d05d..72f3591 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
+++ b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
@@ -183,6 +183,18 @@ config ATH79_MACH_AP152
select ATH79_DEV_WMAC
select ATH79_DEV_AP9X_PCI if PCI
+config ATH79_MACH_AP531B0
+ bool "Rockeetech AP531B0 support"
+ select SOC_QCA953X
+ select ATH79_DEV_AP9X_PCI if PCI
+ select ATH79_DEV_ETH
+ select ATH79_DEV_GPIO_BUTTONS
+ select ATH79_DEV_LEDS_GPIO
+ select ATH79_DEV_M25P80
+ select ATH79_DEV_SPI
+ select ATH79_DEV_USB
+ select ATH79_DEV_WMAC
+
config ATH79_MACH_AP90Q
bool "YunCore AP90Q support"
select SOC_QCA953X
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Makefile b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
index 6475259..7383244 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/Makefile
+++ b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
@@ -53,6 +53,7 @@ obj-$(CONFIG_ATH79_MACH_AP136) += mach-ap136.o
obj-$(CONFIG_ATH79_MACH_AP143) += mach-ap143.o
obj-$(CONFIG_ATH79_MACH_AP147) += mach-ap147.o
obj-$(CONFIG_ATH79_MACH_AP152) += mach-ap152.o
+obj-$(CONFIG_ATH79_MACH_AP531B0) += mach-ap531b0.o
obj-$(CONFIG_ATH79_MACH_AP90Q) += mach-ap90q.o
obj-$(CONFIG_ATH79_MACH_AP96) += mach-ap96.o
obj-$(CONFIG_ATH79_MACH_ARCHER_C59_V1) += mach-archer-c59-v1.o
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-ap531b0.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-ap531b0.c
new file mode 100644
index 0000000..3cb2697
--- /dev/null
+++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-ap531b0.c
@@ -0,0 +1,112 @@
+/*
+ * Rockeetech AP531B0 11ng wireless AP board support
+ *
+ * Copyright (C) 2013 Gabor Juhos <juhosg at openwrt.org>
+ * Copyright (C) 2016 Shuanglin Liu <roboidler at gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/ath9k_platform.h>
+#include <linux/ar8216_platform.h>
+
+#include <asm/mach-ath79/ar71xx_regs.h>
+
+#include "common.h"
+#include "dev-eth.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-m25p80.h"
+#include "dev-spi.h"
+#include "dev-usb.h"
+#include "dev-wmac.h"
+#include "machtypes.h"
+#include "pci.h"
+#include "dev-ap9x-pci.h"
+
+#define AP531B0_GPIO_LED_WLAN 12
+#define AP531B0_GPIO_LED_STATUS 11
+
+#define AP531B0_GPIO_RST_BTN 17
+
+#define AP531B0_KEYS_POLL_INTERVAL 20 /* msecs */
+#define AP531B0_KEYS_DEBOUNCE_INTERVAL (3 * AP531B0_KEYS_POLL_INTERVAL)
+
+#define AP531B0_WMAC_CALDATA_OFFSET 0x1000
+
+
+static struct gpio_led ap531b0_leds_gpio[] __initdata = {
+ {
+ .name = "ap531b0:green:status",
+ .gpio = AP531B0_GPIO_LED_STATUS,
+ .active_low = 1,
+ },
+ {
+ .name = "ap531b0:green:wlan",
+ .gpio = AP531B0_GPIO_LED_WLAN,
+ .active_low = 1,
+ }
+};
+
+static struct gpio_keys_button ap531b0_gpio_keys[] __initdata = {
+ {
+ .desc = "reset",
+ .type = EV_KEY,
+ .code = KEY_RESTART,
+ .debounce_interval = AP531B0_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = AP531B0_GPIO_RST_BTN,
+ .active_low = 1,
+ },
+};
+
+
+static void __init ap531b0_gpio_led_setup(void)
+{
+
+ ath79_register_leds_gpio(-1, ARRAY_SIZE(ap531b0_leds_gpio),
+ ap531b0_leds_gpio);
+
+ ath79_register_gpio_keys_polled(-1, AP531B0_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(ap531b0_gpio_keys),
+ ap531b0_gpio_keys);
+}
+
+static void __init ap531b0_setup(void)
+{
+ u8 *art = (u8 *) KSEG1ADDR(0x1fff0000);
+ u8 *pmac;
+
+ ath79_register_m25p80(NULL);
+ ap531b0_gpio_led_setup();
+ ath79_register_usb();
+ ath79_register_pci();
+
+ ath79_register_mdio(0, 0x0);
+
+ pmac = art + AP531B0_WMAC_CALDATA_OFFSET + 2;
+ ath79_init_mac(ath79_eth0_data.mac_addr, pmac, 1);
+ ath79_init_mac(ath79_eth1_data.mac_addr, pmac, 2);
+
+ ath79_register_wmac(art + AP531B0_WMAC_CALDATA_OFFSET, pmac);
+
+ /* WAN port */
+ ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
+ ath79_eth0_data.speed = SPEED_100;
+ ath79_eth0_data.duplex = DUPLEX_FULL;
+ ath79_eth0_data.phy_mask = BIT(4);
+ ath79_register_eth(0);
+
+ /* LAN ports */
+ ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII;
+ ath79_eth1_data.speed = SPEED_1000;
+ ath79_eth1_data.duplex = DUPLEX_FULL;
+ ath79_switch_data.phy_poll_mask |= BIT(4);
+ ath79_switch_data.phy4_mii_en = 1;
+ ath79_register_eth(1);
+}
+
+MIPS_MACHINE(ATH79_MACH_AP531B0, "AP531B0", "Rockeetech AP531B0",
+ ap531b0_setup);
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
index 4cad628..f3277cd 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
+++ b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
@@ -37,6 +37,7 @@ enum ath79_mach_type {
ATH79_MACH_AP143, /* Atheros AP143 reference board */
ATH79_MACH_AP147_010, /* Atheros AP147-010 reference board */
ATH79_MACH_AP152, /* Atheros AP152 reference board */
+ ATH79_MACH_AP531B0, /* Rockeetech AP531B0 */
ATH79_MACH_AP90Q, /* YunCore AP90Q */
ATH79_MACH_AP96, /* Atheros AP96 */
ATH79_MACH_ARCHER_C5, /* TP-LINK Archer C5 board */
diff --git a/target/linux/ar71xx/image/generic.mk b/target/linux/ar71xx/image/generic.mk
index 02f0747..34bb7da 100644
--- a/target/linux/ar71xx/image/generic.mk
+++ b/target/linux/ar71xx/image/generic.mk
@@ -1,3 +1,12 @@
+define Device/ap531b0
+ DEVICE_TITLE := Rockeetech AP531B0
+ DEVICE_PACKAGES := kmod-usb-core kmod-usb2
+ BOARDNAME = AP531B0
+ IMAGE_SIZE := 16000k
+ MTDPARTS := spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,16000k(firmware),64k(art)ro
+endef
+TARGET_DEVICES += ap531b0
+
define Device/ap90q
DEVICE_TITLE := YunCore AP90Q
BOARDNAME = AP90Q
diff --git a/target/linux/ar71xx/mikrotik/config-default b/target/linux/ar71xx/mikrotik/config-default
index 7339149..cf6f754 100644
--- a/target/linux/ar71xx/mikrotik/config-default
+++ b/target/linux/ar71xx/mikrotik/config-default
@@ -13,6 +13,7 @@
# CONFIG_ATH79_MACH_AP143 is not set
# CONFIG_ATH79_MACH_AP147 is not set
# CONFIG_ATH79_MACH_AP152 is not set
+# CONFIG_ATH79_MACH_AP531B0 is not set
# CONFIG_ATH79_MACH_AP90Q is not set
# CONFIG_ATH79_MACH_AP96 is not set
# CONFIG_ATH79_MACH_ARCHER_C59_V1 is not set
diff --git a/target/linux/ar71xx/nand/config-default b/target/linux/ar71xx/nand/config-default
index 14504a4..24e712c 100644
--- a/target/linux/ar71xx/nand/config-default
+++ b/target/linux/ar71xx/nand/config-default
@@ -13,6 +13,7 @@
# CONFIG_ATH79_MACH_AP143 is not set
# CONFIG_ATH79_MACH_AP147 is not set
# CONFIG_ATH79_MACH_AP152 is not set
+# CONFIG_ATH79_MACH_AP531B0 is not set
# CONFIG_ATH79_MACH_AP90Q is not set
# CONFIG_ATH79_MACH_AP96 is not set
# CONFIG_ATH79_MACH_ARCHER_C59_V1 is not set
More information about the lede-commits
mailing list