[source] kirkwood: drop kernel 4.4 support
LEDE Commits
lede-commits at lists.infradead.org
Tue Jul 4 11:58:57 PDT 2017
mkresin pushed a commit to source.git, branch master:
https://git.lede-project.org/0825de2df7b7a13e5185140e1a5c0318aa16afe4
commit 0825de2df7b7a13e5185140e1a5c0318aa16afe4
Author: Mathias Kresin <dev at kresin.me>
AuthorDate: Wed Jun 28 23:34:51 2017 +0200
kirkwood: drop kernel 4.4 support
Signed-off-by: Mathias Kresin <dev at kresin.me>
---
target/linux/kirkwood/config-4.4 | 326 ---------------------
.../patches-4.4/100-find_active_root.patch | 61 ----
target/linux/kirkwood/patches-4.4/110-ib62x0.patch | 21 --
.../linux/kirkwood/patches-4.4/130-iconnect.patch | 41 ---
.../linux/kirkwood/patches-4.4/140-dockstar.patch | 32 --
target/linux/kirkwood/patches-4.4/160-ea4500.patch | 200 -------------
target/linux/kirkwood/patches-4.4/170-ea3500.patch | 192 ------------
.../kirkwood/patches-4.4/180-goflexhome.patch | 130 --------
.../linux/kirkwood/patches-4.4/181-goflexnet.patch | 23 --
.../190-zyxel-nsa3xx-common-nand-partitions.patch | 47 ---
.../linux/kirkwood/patches-4.4/191-nsa310b.patch | 169 -----------
.../linux/kirkwood/patches-4.4/192-nsa310s.patch | 300 -------------------
target/linux/kirkwood/patches-4.4/194-nsa325.patch | 233 ---------------
target/linux/kirkwood/patches-4.4/195-on100.patch | 173 -----------
.../kirkwood/patches-4.4/200-disable-tso.patch | 35 ---
...10-enable-sata-port-specific-led-triggers.patch | 10 -
16 files changed, 1993 deletions(-)
diff --git a/target/linux/kirkwood/config-4.4 b/target/linux/kirkwood/config-4.4
deleted file mode 100644
index 90a668a..0000000
--- a/target/linux/kirkwood/config-4.4
+++ /dev/null
@@ -1,326 +0,0 @@
-CONFIG_ALIGNMENT_TRAP=y
-CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
-CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
-CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y
-CONFIG_ARCH_HAS_SG_CHAIN=y
-CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
-CONFIG_ARCH_HIBERNATION_POSSIBLE=y
-CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
-CONFIG_ARCH_MULTIPLATFORM=y
-CONFIG_ARCH_MULTI_CPU_AUTO=y
-# CONFIG_ARCH_MULTI_V4 is not set
-# CONFIG_ARCH_MULTI_V4T is not set
-CONFIG_ARCH_MULTI_V4_V5=y
-CONFIG_ARCH_MULTI_V5=y
-CONFIG_ARCH_MVEBU=y
-CONFIG_ARCH_NR_GPIO=0
-CONFIG_ARCH_REQUIRE_GPIOLIB=y
-# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
-# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
-CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
-CONFIG_ARCH_SUPPORTS_BIG_ENDIAN=y
-CONFIG_ARCH_SUPPORTS_UPROBES=y
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_ARCH_USE_BUILTIN_BSWAP=y
-CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y
-CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
-CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
-CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
-CONFIG_ARCH_WANT_LIBATA_LEDS=y
-CONFIG_ARM=y
-# CONFIG_ARMADA_THERMAL is not set
-CONFIG_ARM_APPENDED_DTB=y
-CONFIG_ARM_ATAG_DTB_COMPAT=y
-# CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND is not set
-CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER=y
-# CONFIG_ARM_CPU_SUSPEND is not set
-CONFIG_ARM_HAS_SG_CHAIN=y
-# CONFIG_ARM_KIRKWOOD_CPUIDLE is not set
-CONFIG_ARM_L1_CACHE_SHIFT=5
-# CONFIG_ARM_MVEBU_V7_CPUIDLE is not set
-CONFIG_ARM_PATCH_PHYS_VIRT=y
-# CONFIG_ARM_THUMB is not set
-CONFIG_ATA=y
-CONFIG_ATAGS=y
-CONFIG_ATA_LEDS=y
-CONFIG_AUTO_ZRELADDR=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_CACHE_FEROCEON_L2=y
-# CONFIG_CACHE_FEROCEON_L2_WRITETHROUGH is not set
-# CONFIG_CACHE_L2X0 is not set
-CONFIG_CLKDEV_LOOKUP=y
-CONFIG_CLKSRC_MMIO=y
-CONFIG_CLKSRC_OF=y
-CONFIG_CLKSRC_PROBE=y
-CONFIG_CLONE_BACKWARDS=y
-CONFIG_COMMON_CLK=y
-CONFIG_CPU_32v5=y
-CONFIG_CPU_ABRT_EV5T=y
-# CONFIG_CPU_BIG_ENDIAN is not set
-CONFIG_CPU_CACHE_VIVT=y
-CONFIG_CPU_COPY_FEROCEON=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-CONFIG_CPU_FEROCEON=y
-# CONFIG_CPU_FEROCEON_OLD_ID is not set
-# CONFIG_CPU_ICACHE_DISABLE is not set
-CONFIG_CPU_IDLE=y
-CONFIG_CPU_IDLE_GOV_LADDER=y
-CONFIG_CPU_PABRT_LEGACY=y
-CONFIG_CPU_PM=y
-CONFIG_CPU_TLB_FEROCEON=y
-CONFIG_CPU_USE_DOMAINS=y
-CONFIG_CRC16=y
-# CONFIG_CRC32_SARWATE is not set
-CONFIG_CRC32_SLICEBY8=y
-CONFIG_CRYPTO_CRC32C=y
-CONFIG_CRYPTO_DEFLATE=y
-CONFIG_CRYPTO_DES=y
-CONFIG_CRYPTO_DEV_MARVELL_CESA=y
-CONFIG_CRYPTO_HASH=y
-CONFIG_CRYPTO_HASH2=y
-CONFIG_CRYPTO_HW=y
-CONFIG_CRYPTO_LZO=y
-CONFIG_CRYPTO_RNG2=y
-CONFIG_CRYPTO_WORKQUEUE=y
-CONFIG_DEBUG_LL=y
-CONFIG_DEBUG_LL_INCLUDE="debug/8250.S"
-CONFIG_DEBUG_MVEBU_UART0=y
-# CONFIG_DEBUG_MVEBU_UART0_ALTERNATE is not set
-# CONFIG_DEBUG_MVEBU_UART1_ALTERNATE is not set
-CONFIG_DEBUG_UART_8250=y
-# CONFIG_DEBUG_UART_8250_FLOW_CONTROL is not set
-CONFIG_DEBUG_UART_8250_SHIFT=2
-# CONFIG_DEBUG_UART_8250_WORD is not set
-CONFIG_DEBUG_UART_PHYS=0xf1012000
-CONFIG_DEBUG_UART_VIRT=0xfed12000
-CONFIG_DEBUG_UNCOMPRESS=y
-# CONFIG_DEBUG_USER is not set
-# CONFIG_DLCI is not set
-CONFIG_DNOTIFY=y
-CONFIG_DTC=y
-# CONFIG_EARLY_PRINTK is not set
-CONFIG_EDAC_ATOMIC_SCRUB=y
-CONFIG_EDAC_SUPPORT=y
-CONFIG_EXT4_FS=y
-CONFIG_FIX_EARLYCON_MEM=y
-CONFIG_FRAME_POINTER=y
-CONFIG_FS_MBCACHE=y
-CONFIG_GENERIC_ALLOCATOR=y
-CONFIG_GENERIC_ATOMIC64=y
-CONFIG_GENERIC_BUG=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_GENERIC_IDLE_POLL_SETUP=y
-CONFIG_GENERIC_IO=y
-CONFIG_GENERIC_IRQ_CHIP=y
-CONFIG_GENERIC_IRQ_SHOW=y
-CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
-CONFIG_GENERIC_PCI_IOMAP=y
-CONFIG_GENERIC_PHY=y
-CONFIG_GENERIC_SCHED_CLOCK=y
-CONFIG_GENERIC_SMP_IDLE_THREAD=y
-CONFIG_GENERIC_STRNCPY_FROM_USER=y
-CONFIG_GENERIC_STRNLEN_USER=y
-CONFIG_GLOB=y
-CONFIG_GPIOLIB=y
-CONFIG_GPIO_DEVRES=y
-CONFIG_GPIO_MVEBU=y
-CONFIG_GPIO_SYSFS=y
-CONFIG_HANDLE_DOMAIN_IRQ=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT_MAP=y
-# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
-CONFIG_HAVE_ARCH_AUDITSYSCALL=y
-# CONFIG_HAVE_ARCH_BITREVERSE is not set
-CONFIG_HAVE_ARCH_JUMP_LABEL=y
-CONFIG_HAVE_ARCH_KGDB=y
-CONFIG_HAVE_ARCH_PFN_VALID=y
-CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
-CONFIG_HAVE_ARCH_TRACEHOOK=y
-# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
-CONFIG_HAVE_BPF_JIT=y
-CONFIG_HAVE_CC_STACKPROTECTOR=y
-CONFIG_HAVE_CLK=y
-CONFIG_HAVE_CLK_PREPARE=y
-CONFIG_HAVE_CONTEXT_TRACKING=y
-CONFIG_HAVE_C_RECORDMCOUNT=y
-CONFIG_HAVE_DEBUG_KMEMLEAK=y
-CONFIG_HAVE_DMA_API_DEBUG=y
-CONFIG_HAVE_DMA_ATTRS=y
-CONFIG_HAVE_DMA_CONTIGUOUS=y
-CONFIG_HAVE_DYNAMIC_FTRACE=y
-CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
-CONFIG_HAVE_FUNCTION_TRACER=y
-CONFIG_HAVE_GENERIC_DMA_COHERENT=y
-CONFIG_HAVE_IDE=y
-CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
-CONFIG_HAVE_LATENCYTOP_SUPPORT=y
-CONFIG_HAVE_MEMBLOCK=y
-CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
-CONFIG_HAVE_NET_DSA=y
-CONFIG_HAVE_OPROFILE=y
-CONFIG_HAVE_OPTPROBES=y
-CONFIG_HAVE_PERF_EVENTS=y
-CONFIG_HAVE_PERF_REGS=y
-CONFIG_HAVE_PERF_USER_STACK_DUMP=y
-CONFIG_HAVE_PROC_CPU=y
-CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
-CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
-CONFIG_HAVE_UID16=y
-CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
-CONFIG_HW_RANDOM=y
-CONFIG_HZ_FIXED=0
-CONFIG_HZ_PERIODIC=y
-CONFIG_I2C=y
-CONFIG_I2C_BOARDINFO=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_MV64XXX=y
-CONFIG_INITRAMFS_SOURCE=""
-CONFIG_IOMMU_HELPER=y
-CONFIG_IP_PIMSM_V1=y
-CONFIG_IP_PIMSM_V2=y
-CONFIG_IRQCHIP=y
-CONFIG_IRQ_DOMAIN=y
-CONFIG_IRQ_FORCED_THREADING=y
-CONFIG_IRQ_WORK=y
-CONFIG_JBD2=y
-CONFIG_KIRKWOOD_CLK=y
-CONFIG_KIRKWOOD_THERMAL=y
-CONFIG_LEDS_GPIO=y
-CONFIG_LEDS_NETXBIG=y
-CONFIG_LEDS_NS2=y
-CONFIG_LEGACY_PTYS=y
-CONFIG_LEGACY_PTY_COUNT=256
-CONFIG_LIBFDT=y
-CONFIG_LZO_COMPRESS=y
-CONFIG_LZO_DECOMPRESS=y
-CONFIG_MACH_KIRKWOOD=y
-CONFIG_MACH_MVEBU_ANY=y
-CONFIG_MANGLE_BOOTARGS=y
-CONFIG_MDIO_BOARDINFO=y
-CONFIG_MIGHT_HAVE_PCI=y
-CONFIG_MMC=y
-CONFIG_MMC_BLOCK=y
-CONFIG_MMC_MVSDIO=y
-# CONFIG_MMC_TIFM_SD is not set
-CONFIG_MODULES_USE_ELF_REL=y
-# CONFIG_MTD_CFI is not set
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_ECC=y
-CONFIG_MTD_NAND_ORION=y
-CONFIG_MTD_UBI=y
-CONFIG_MTD_UBI_BEB_LIMIT=20
-CONFIG_MTD_UBI_BLOCK=y
-# CONFIG_MTD_UBI_FASTMAP is not set
-# CONFIG_MTD_UBI_GLUEBI is not set
-CONFIG_MTD_UBI_WL_THRESHOLD=4096
-CONFIG_MULTI_IRQ_HANDLER=y
-CONFIG_MV643XX_ETH=y
-CONFIG_MVEBU_CLK_COMMON=y
-CONFIG_MVEBU_MBUS=y
-CONFIG_MVMDIO=y
-# CONFIG_MVNETA is not set
-CONFIG_MVSW61XX_PHY=y
-CONFIG_NEED_DMA_MAP_STATE=y
-CONFIG_NEED_KUSER_HELPERS=y
-CONFIG_NEED_PER_CPU_KM=y
-CONFIG_NLS=y
-CONFIG_NO_BOOTMEM=y
-CONFIG_OF=y
-CONFIG_OF_ADDRESS=y
-CONFIG_OF_ADDRESS_PCI=y
-CONFIG_OF_EARLY_FLATTREE=y
-CONFIG_OF_FLATTREE=y
-CONFIG_OF_GPIO=y
-CONFIG_OF_IRQ=y
-CONFIG_OF_MDIO=y
-CONFIG_OF_MTD=y
-CONFIG_OF_NET=y
-CONFIG_OF_PCI=y
-CONFIG_OF_PCI_IRQ=y
-CONFIG_OF_RESERVED_MEM=y
-CONFIG_OLD_SIGACTION=y
-CONFIG_OLD_SIGSUSPEND3=y
-CONFIG_ORION_IRQCHIP=y
-CONFIG_ORION_TIMER=y
-CONFIG_ORION_WATCHDOG=y
-CONFIG_OUTER_CACHE=y
-CONFIG_PAGE_OFFSET=0xC0000000
-CONFIG_PCI=y
-# CONFIG_PCI_DOMAINS_GENERIC is not set
-CONFIG_PCI_MVEBU=y
-CONFIG_PERF_USE_VMALLOC=y
-CONFIG_PGTABLE_LEVELS=2
-CONFIG_PHYLIB=y
-CONFIG_PHY_MVEBU_SATA=y
-CONFIG_PINCTRL=y
-CONFIG_PINCTRL_KIRKWOOD=y
-CONFIG_PINCTRL_MVEBU=y
-# CONFIG_PINCTRL_SINGLE is not set
-CONFIG_PLAT_ORION=y
-CONFIG_POWER_RESET=y
-CONFIG_POWER_RESET_GPIO=y
-# CONFIG_POWER_RESET_QNAP is not set
-CONFIG_POWER_SUPPLY=y
-CONFIG_RATIONAL=y
-# CONFIG_RCU_STALL_COMMON is not set
-CONFIG_REGMAP=y
-CONFIG_REGULATOR=y
-CONFIG_REGULATOR_FIXED_VOLTAGE=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_MV=y
-CONFIG_RWSEM_XCHGADD_ALGORITHM=y
-CONFIG_SATA_MV=y
-# CONFIG_SCHED_INFO is not set
-CONFIG_SCSI=y
-CONFIG_SERIAL_8250_DEPRECATED_OPTIONS=y
-CONFIG_SERIAL_8250_FSL=y
-CONFIG_SERIAL_OF_PLATFORM=y
-CONFIG_SOC_BUS=y
-CONFIG_SPARSE_IRQ=y
-CONFIG_SPI=y
-CONFIG_SPI_MASTER=y
-CONFIG_SPI_ORION=y
-CONFIG_SPLIT_PTLOCK_CPUS=999999
-CONFIG_SRAM=y
-CONFIG_SRCU=y
-CONFIG_SWCONFIG=y
-CONFIG_SWIOTLB=y
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-CONFIG_THERMAL=y
-CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
-CONFIG_THERMAL_GOV_STEP_WISE=y
-CONFIG_THERMAL_OF=y
-CONFIG_TICK_CPU_ACCOUNTING=y
-CONFIG_UBIFS_FS=y
-CONFIG_UBIFS_FS_ADVANCED_COMPR=y
-CONFIG_UBIFS_FS_LZO=y
-CONFIG_UBIFS_FS_ZLIB=y
-CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h"
-CONFIG_USB=y
-CONFIG_USB_COMMON=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_EHCI_HCD_ORION=y
-# CONFIG_USB_EHCI_HCD_PLATFORM is not set
-CONFIG_USB_EHCI_PCI=y
-CONFIG_USB_LED_TRIG=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_SUPPORT=y
-# CONFIG_USB_UHCI_HCD is not set
-CONFIG_USE_OF=y
-CONFIG_VECTORS_BASE=0xffff0000
-# CONFIG_VFP is not set
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_WAN=y
-CONFIG_WATCHDOG_CORE=y
-CONFIG_XZ_DEC_ARM=y
-CONFIG_XZ_DEC_BCJ=y
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZLIB_DEFLATE=y
-CONFIG_ZLIB_INFLATE=y
-CONFIG_ZONE_DMA_FLAG=0
diff --git a/target/linux/kirkwood/patches-4.4/100-find_active_root.patch b/target/linux/kirkwood/patches-4.4/100-find_active_root.patch
deleted file mode 100644
index b39afed..0000000
--- a/target/linux/kirkwood/patches-4.4/100-find_active_root.patch
+++ /dev/null
@@ -1,61 +0,0 @@
-The WRT1900AC among other Linksys routers uses a dual-firmware layout.
-Dynamically rename the active partition to "ubi".
-
-Signed-off-by: Imre Kaloz <kaloz at openwrt.org>
-
---- a/drivers/mtd/ofpart.c
-+++ b/drivers/mtd/ofpart.c
-@@ -25,12 +25,15 @@ static bool node_has_compatible(struct d
- return of_get_property(pp, "compatible", NULL);
- }
-
-+static int mangled_rootblock;
-+
- static int parse_ofpart_partitions(struct mtd_info *master,
- struct mtd_partition **pparts,
- struct mtd_part_parser_data *data)
- {
- struct device_node *mtd_node;
- struct device_node *ofpart_node;
-+ const char *owrtpart = "ubi";
- const char *partname;
- struct device_node *pp;
- int nr_parts, i, ret = 0;
-@@ -110,9 +113,15 @@ static int parse_ofpart_partitions(struc
- (*pparts)[i].offset = of_read_number(reg, a_cells);
- (*pparts)[i].size = of_read_number(reg + a_cells, s_cells);
-
-- partname = of_get_property(pp, "label", &len);
-- if (!partname)
-- partname = of_get_property(pp, "name", &len);
-+ if (mangled_rootblock && (i == mangled_rootblock)) {
-+ partname = owrtpart;
-+ } else {
-+ partname = of_get_property(pp, "label", &len);
-+
-+ if (!partname)
-+ partname = of_get_property(pp, "name", &len);
-+ }
-+
- (*pparts)[i].name = partname;
-
- if (of_get_property(pp, "read-only", &len))
-@@ -215,6 +224,18 @@ static int __init ofpart_parser_init(voi
- return 0;
- }
-
-+static int __init active_root(char *str)
-+{
-+ get_option(&str, &mangled_rootblock);
-+
-+ if (!mangled_rootblock)
-+ return 1;
-+
-+ return 1;
-+}
-+
-+__setup("mangled_rootblock=", active_root);
-+
- static void __exit ofpart_parser_exit(void)
- {
- deregister_mtd_parser(&ofpart_parser);
diff --git a/target/linux/kirkwood/patches-4.4/110-ib62x0.patch b/target/linux/kirkwood/patches-4.4/110-ib62x0.patch
deleted file mode 100644
index d6d10d8..0000000
--- a/target/linux/kirkwood/patches-4.4/110-ib62x0.patch
+++ /dev/null
@@ -1,21 +0,0 @@
---- a/arch/arm/boot/dts/kirkwood-ib62x0.dts
-+++ b/arch/arm/boot/dts/kirkwood-ib62x0.dts
-@@ -117,13 +117,13 @@
- };
-
- partition at 100000 {
-- label = "uImage";
-- reg = <0x0100000 0x600000>;
-+ label = "second stage u-boot";
-+ reg = <0x100000 0x200000>;
- };
-
-- partition at 700000 {
-- label = "root";
-- reg = <0x0700000 0xf900000>;
-+ partition at 200000 {
-+ label = "ubi";
-+ reg = <0x200000 0xfe00000>;
- };
-
- };
diff --git a/target/linux/kirkwood/patches-4.4/130-iconnect.patch b/target/linux/kirkwood/patches-4.4/130-iconnect.patch
deleted file mode 100644
index 2d0a376..0000000
--- a/target/linux/kirkwood/patches-4.4/130-iconnect.patch
+++ /dev/null
@@ -1,41 +0,0 @@
---- a/arch/arm/boot/dts/kirkwood-iconnect.dts
-+++ b/arch/arm/boot/dts/kirkwood-iconnect.dts
-@@ -155,28 +155,23 @@
- status = "okay";
-
- partition at 0 {
-- label = "uboot";
-- reg = <0x0000000 0xc0000>;
-+ label = "u-boot";
-+ reg = <0x0000000 0xe0000>;
- };
-
-- partition at a0000 {
-- label = "env";
-- reg = <0xa0000 0x20000>;
-+ partition at e0000 {
-+ label = "u-boot environment";
-+ reg = <0xe0000 0x100000>;
- };
-
- partition at 100000 {
-- label = "zImage";
-- reg = <0x100000 0x300000>;
-+ label = "second stage u-boot";
-+ reg = <0x100000 0x200000>;
- };
-
-- partition at 540000 {
-- label = "initrd";
-- reg = <0x540000 0x300000>;
-- };
--
-- partition at 980000 {
-- label = "boot";
-- reg = <0x980000 0x1f400000>;
-+ partition at 200000 {
-+ label = "ubi";
-+ reg = <0x200000 0x1fe00000>;
- };
- };
-
diff --git a/target/linux/kirkwood/patches-4.4/140-dockstar.patch b/target/linux/kirkwood/patches-4.4/140-dockstar.patch
deleted file mode 100644
index f66e19d..0000000
--- a/target/linux/kirkwood/patches-4.4/140-dockstar.patch
+++ /dev/null
@@ -1,32 +0,0 @@
---- a/arch/arm/boot/dts/kirkwood-dockstar.dts
-+++ b/arch/arm/boot/dts/kirkwood-dockstar.dts
-@@ -77,18 +77,22 @@
-
- partition at 0 {
- label = "u-boot";
-- reg = <0x0000000 0x100000>;
-- read-only;
-+ reg = <0x0000000 0xe0000>;
-+ };
-+
-+ partition at e0000 {
-+ label = "u-boot environment";
-+ reg = <0xe0000 0x100000>;
- };
-
- partition at 100000 {
-- label = "uImage";
-- reg = <0x0100000 0x400000>;
-+ label = "second stage u-boot";
-+ reg = <0x100000 0x200000>;
- };
-
-- partition at 500000 {
-- label = "data";
-- reg = <0x0500000 0xfb00000>;
-+ partition at 200000 {
-+ label = "ubi";
-+ reg = <0x200000 0xfe00000>;
- };
- };
-
diff --git a/target/linux/kirkwood/patches-4.4/160-ea4500.patch b/target/linux/kirkwood/patches-4.4/160-ea4500.patch
deleted file mode 100644
index baf6e01..0000000
--- a/target/linux/kirkwood/patches-4.4/160-ea4500.patch
+++ /dev/null
@@ -1,200 +0,0 @@
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -183,6 +183,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- kirkwood-is2.dtb \
- kirkwood-km_kirkwood.dtb \
- kirkwood-laplug.dtb \
-+ kirkwood-linksys-viper.dtb \
- kirkwood-lschlv2.dtb \
- kirkwood-lswvl.dtb \
- kirkwood-lswxl.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-linksys-viper.dts
-@@ -0,0 +1,187 @@
-+/*
-+ * kirkwood-linksys-viper.dts - Device Tree file for Linksys E4200v2/EA4500
-+ *
-+ * (c) 2013 Jonas Gorski <jogo at openwrt.org>
-+ * (c) 2013 Deutsche Telekom Innovation Laboratories
-+ * (c) 2014 Luka Perkov <luka at openwrt.org>
-+ *
-+ * This file is licensed under the terms of the GNU General Public
-+ * License version 2. This program is licensed "as is" without any
-+ * warranty of any kind, whether express or implied.
-+ */
-+
-+/dts-v1/;
-+
-+#include "kirkwood.dtsi"
-+#include "kirkwood-6282.dtsi"
-+
-+/ {
-+ model = "Linksys E4200v2 / EA4500";
-+ compatible = "linksys,viper", "marvell,kirkwood-88f6282", "marvell,kirkwood";
-+
-+ memory {
-+ device_type = "memory";
-+ reg = <0x00000000 0x8000000>;
-+ };
-+
-+ chosen {
-+ bootargs = "console=ttyS0,115200n8 earlyprintk";
-+ };
-+
-+ mbus {
-+ pcie-controller {
-+ status = "okay";
-+
-+ pcie at 1,0 {
-+ status = "okay";
-+ };
-+
-+ pcie at 2,0 {
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ ocp at f1000000 {
-+ pinctrl: pin-controller at 10000 {
-+ pmx_led_white_health: pmx-led-white-health {
-+ marvell,pins = "mpp7";
-+ marvell,function = "gpo";
-+ };
-+ pmx_led_white_pulse: pmx-led-white-pulse {
-+ marvell,pins = "mpp14";
-+ marvell,function = "gpio";
-+ };
-+ pmx_btn_wps: pmx-btn-wps {
-+ marvell,pins = "mpp47";
-+ marvell,function = "gpio";
-+ };
-+ pmx_btn_reset: pmx-btn-reset {
-+ marvell,pins = "mpp48";
-+ marvell,function = "gpio";
-+ };
-+ };
-+
-+ rtc at 10300 {
-+ status = "disabled";
-+ };
-+
-+ serial at 12000 {
-+ status = "okay";
-+ };
-+
-+ };
-+
-+ gpio_keys {
-+ compatible = "gpio-keys";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ pinctrl-0 = < &pmx_btn_wps &pmx_btn_reset >;
-+ pinctrl-names = "default";
-+
-+ button at 15 {
-+ label = "WPS Button";
-+ linux,code = <KEY_WPS_BUTTON>;
-+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
-+ };
-+
-+ button at 16 {
-+ label = "Reset Button";
-+ linux,code = <KEY_RESTART>;
-+ gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
-+ };
-+ };
-+
-+ gpio-leds {
-+ compatible = "gpio-leds";
-+ pinctrl-0 = < &pmx_led_white_health &pmx_led_white_pulse >;
-+ pinctrl-names = "default";
-+
-+ white-health {
-+ label = "viper:white:health";
-+ gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ white-pulse {
-+ label = "viper:white:pulse";
-+ gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
-+ };
-+ };
-+
-+ mvsw61xx {
-+ compatible = "marvell,88e6171";
-+ status = "okay";
-+ reg = <0x10>;
-+
-+ mii-bus = <&mdio>;
-+ cpu-port-0 = <5>;
-+ cpu-port-1 = <6>;
-+ is-indirect;
-+ };
-+};
-+
-+&nand {
-+ status = "okay";
-+ pinctrl-0 = <&pmx_nand>;
-+ pinctrl-names = "default";
-+
-+ partition at 0 {
-+ label = "u-boot";
-+ reg = <0x0 0x80000>;
-+ };
-+
-+ partition at 80000 {
-+ label = "u_env";
-+ reg = <0x80000 0x20000>;
-+ };
-+
-+ partition at a0000 {
-+ label = "s_env";
-+ reg = <0xa0000 0x20000>;
-+ };
-+
-+ partition at 200000 {
-+ label = "kernel1";
-+ reg = <0x200000 0x1a00000>;
-+ };
-+
-+ partition at 4a0000 {
-+ label = "rootfs1";
-+ reg = <0x4a0000 0x1760000>;
-+ };
-+
-+ partition at 1c00000 {
-+ label = "kernel2";
-+ reg = <0x1c00000 0x1a00000>;
-+ };
-+
-+ partition at 1ea0000 {
-+ label = "rootfs2";
-+ reg = <0x1ea0000 0x1760000>;
-+ };
-+
-+ partition at 3600000 {
-+ label = "syscfg";
-+ reg = <0x3600000 0x4a00000>;
-+ };
-+};
-+
-+&mdio {
-+ status = "okay";
-+};
-+
-+ð0 {
-+ status = "okay";
-+ ethernet0-port at 0 {
-+ speed = <1000>;
-+ duplex = <1>;
-+ };
-+};
-+
-+ð1 {
-+ status = "okay";
-+ ethernet1-port at 0 {
-+ speed = <1000>;
-+ duplex = <1>;
-+ };
-+};
diff --git a/target/linux/kirkwood/patches-4.4/170-ea3500.patch b/target/linux/kirkwood/patches-4.4/170-ea3500.patch
deleted file mode 100644
index bc7ce34..0000000
--- a/target/linux/kirkwood/patches-4.4/170-ea3500.patch
+++ /dev/null
@@ -1,192 +0,0 @@
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -183,6 +183,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- kirkwood-is2.dtb \
- kirkwood-km_kirkwood.dtb \
- kirkwood-laplug.dtb \
-+ kirkwood-linksys-audi.dtb \
- kirkwood-linksys-viper.dtb \
- kirkwood-lschlv2.dtb \
- kirkwood-lswvl.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-linksys-audi.dts
-@@ -0,0 +1,179 @@
-+/*
-+ * kirkwood-linksys-audi.dts - Device Tree file for Linksys EA3500
-+ *
-+ * (c) 2013 Jonas Gorski <jogo at openwrt.org>
-+ * (c) 2013 Deutsche Telekom Innovation Laboratories
-+ * (c) 2014 Luka Perkov <luka at openwrt.org>
-+ * (c) 2014 Dan Walters <dan at walters.io>
-+ *
-+ * This file is licensed under the terms of the GNU General Public
-+ * License version 2. This program is licensed "as is" without any
-+ * warranty of any kind, whether express or implied.
-+ */
-+
-+/dts-v1/;
-+
-+#include "kirkwood.dtsi"
-+#include "kirkwood-6282.dtsi"
-+
-+/ {
-+ model = "Linksys EA3500";
-+ compatible = "linksys,audi", "marvell,kirkwood-88f6282", "marvell,kirkwood";
-+
-+ memory {
-+ device_type = "memory";
-+ reg = <0x00000000 0x4000000>;
-+ };
-+
-+ chosen {
-+ bootargs = "console=ttyS0,115200n8 earlyprintk";
-+ };
-+
-+ mbus {
-+ pcie-controller {
-+ status = "okay";
-+
-+ pcie at 1,0 {
-+ status = "okay";
-+ };
-+
-+ pcie at 2,0 {
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ ocp at f1000000 {
-+ pinctrl: pin-controller at 10000 {
-+ pmx_led_green_power: pmx-led-green-power {
-+ marvell,pins = "mpp7";
-+ marvell,function = "gpo";
-+ };
-+ pmx_btn_wps: pmx-btn-wps {
-+ marvell,pins = "mpp47";
-+ marvell,function = "gpio";
-+ };
-+ pmx_btn_reset: pmx-btn-reset {
-+ marvell,pins = "mpp48";
-+ marvell,function = "gpio";
-+ };
-+ };
-+
-+ rtc at 10300 {
-+ status = "disabled";
-+ };
-+
-+ serial at 12000 {
-+ status = "okay";
-+ };
-+
-+ };
-+
-+ gpio_keys {
-+ compatible = "gpio-keys";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ pinctrl-0 = < &pmx_btn_wps &pmx_btn_reset >;
-+ pinctrl-names = "default";
-+
-+ button at 15 {
-+ label = "WPS Button";
-+ linux,code = <KEY_WPS_BUTTON>;
-+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
-+ };
-+
-+ button at 16 {
-+ label = "Reset Button";
-+ linux,code = <KEY_RESTART>;
-+ gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
-+ };
-+ };
-+
-+ gpio-leds {
-+ compatible = "gpio-leds";
-+ pinctrl-0 = < &pmx_led_green_power >;
-+ pinctrl-names = "default";
-+
-+ green-power {
-+ label = "audi:green:power";
-+ gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
-+ };
-+ };
-+
-+ mvsw61xx {
-+ compatible = "marvell,88e6171";
-+ status = "okay";
-+ reg = <0x10>;
-+
-+ mii-bus = <&mdio>;
-+ cpu-port-0 = <5>;
-+ cpu-port-1 = <6>;
-+ is-indirect;
-+ };
-+};
-+
-+&nand {
-+ status = "okay";
-+ pinctrl-0 = <&pmx_nand>;
-+ pinctrl-names = "default";
-+
-+ partition at 0 {
-+ label = "u-boot";
-+ reg = <0x0 0x80000>;
-+ };
-+
-+ partition at 80000 {
-+ label = "u_env";
-+ reg = <0x80000 0x4000>;
-+ };
-+
-+ partition at 84000 {
-+ label = "s_env";
-+ reg = <0x84000 0x4000>;
-+ };
-+
-+ partition at 200000 {
-+ label = "kernel1";
-+ reg = <0x200000 0x1400000>;
-+ };
-+
-+ partition at 490000 {
-+ label = "rootfs1";
-+ reg = <0x490000 0x1170000>;
-+ };
-+
-+ partition at 1600000 {
-+ label = "kernel2";
-+ reg = <0x1600000 0x1400000>;
-+ };
-+
-+ partition at 1890000 {
-+ label = "rootfs2";
-+ reg = <0x1890000 0x1170000>;
-+ };
-+
-+ partition at 2a00000 {
-+ label = "syscfg";
-+ reg = <0x2a00000 0x1600000>;
-+ };
-+};
-+
-+&mdio {
-+ status = "okay";
-+};
-+
-+ð0 {
-+ status = "okay";
-+ ethernet0-port at 0 {
-+ speed = <1000>;
-+ duplex = <1>;
-+ };
-+};
-+
-+ð1 {
-+ status = "okay";
-+ ethernet1-port at 0 {
-+ speed = <1000>;
-+ duplex = <1>;
-+ };
-+};
diff --git a/target/linux/kirkwood/patches-4.4/180-goflexhome.patch b/target/linux/kirkwood/patches-4.4/180-goflexhome.patch
deleted file mode 100644
index 6a8d350..0000000
--- a/target/linux/kirkwood/patches-4.4/180-goflexhome.patch
+++ /dev/null
@@ -1,130 +0,0 @@
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -175,6 +175,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- kirkwood-ds411.dtb \
- kirkwood-ds411j.dtb \
- kirkwood-ds411slim.dtb \
-+ kirkwood-goflexhome.dtb \
- kirkwood-goflexnet.dtb \
- kirkwood-guruplug-server-plus.dtb \
- kirkwood-ib62x0.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-goflexhome.dts
-@@ -0,0 +1,117 @@
-+/dts-v1/;
-+
-+#include "kirkwood.dtsi"
-+#include "kirkwood-6281.dtsi"
-+
-+/ {
-+ model = "Seagate GoFlex Home";
-+ compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-+
-+ memory {
-+ device_type = "memory";
-+ reg = <0x00000000 0x8000000>;
-+ };
-+
-+ chosen {
-+ bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
-+ stdout-path = &uart0;
-+ };
-+
-+ ocp at f1000000 {
-+ pinctrl: pin-controller at 10000 {
-+ pmx_usb_power_enable: pmx-usb-power-enable {
-+ marvell,pins = "mpp29";
-+ marvell,function = "gpio";
-+ };
-+ pmx_led_white: pmx-led-white {
-+ marvell,pins = "mpp40";
-+ marvell,function = "gpio";
-+ };
-+ pmx_led_green: pmx-led_green {
-+ marvell,pins = "mpp46";
-+ marvell,function = "gpio";
-+ };
-+ pmx_led_orange: pmx-led-orange {
-+ marvell,pins = "mpp47";
-+ marvell,function = "gpio";
-+ };
-+ };
-+ serial at 12000 {
-+ status = "ok";
-+ };
-+
-+ sata at 80000 {
-+ status = "okay";
-+ nr-ports = <2>;
-+ };
-+
-+ };
-+ gpio-leds {
-+ compatible = "gpio-leds";
-+
-+ health {
-+ label = "status:green:health";
-+ gpios = <&gpio1 14 1>;
-+ linux,default-trigger = "default-on";
-+ };
-+ fault {
-+ label = "status:orange:fault";
-+ gpios = <&gpio1 15 1>;
-+ };
-+ misc {
-+ label = "status:white:misc";
-+ gpios = <&gpio1 8 1>;
-+ linux,default-trigger = "ide-disk";
-+ };
-+ };
-+ regulators {
-+ compatible = "simple-bus";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ pinctrl-0 = <&pmx_usb_power_enable>;
-+ pinctrl-names = "default";
-+
-+ usb_power: regulator at 1 {
-+ compatible = "regulator-fixed";
-+ reg = <1>;
-+ regulator-name = "USB Power";
-+ regulator-min-microvolt = <5000000>;
-+ regulator-max-microvolt = <5000000>;
-+ enable-active-high;
-+ regulator-always-on;
-+ regulator-boot-on;
-+ gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
-+ };
-+ };
-+};
-+
-+&nand {
-+ chip-delay = <40>;
-+ status = "okay";
-+
-+ partition at 0 {
-+ label = "u-boot";
-+ reg = <0x0000000 0x100000>;
-+ read-only;
-+ };
-+
-+ partition at 100000 {
-+ label = "ubi";
-+ reg = <0x100000 0x0ff00000>;
-+ };
-+};
-+
-+&mdio {
-+ status = "okay";
-+
-+ ethphy0: ethernet-phy at 0 {
-+ reg = <0>;
-+ };
-+};
-+
-+ð0 {
-+ status = "okay";
-+ ethernet0-port at 0 {
-+ phy-handle = <ðphy0>;
-+ };
-+};
diff --git a/target/linux/kirkwood/patches-4.4/181-goflexnet.patch b/target/linux/kirkwood/patches-4.4/181-goflexnet.patch
deleted file mode 100644
index 9b0620b..0000000
--- a/target/linux/kirkwood/patches-4.4/181-goflexnet.patch
+++ /dev/null
@@ -1,23 +0,0 @@
---- a/arch/arm/boot/dts/kirkwood-goflexnet.dts
-+++ b/arch/arm/boot/dts/kirkwood-goflexnet.dts
-@@ -158,18 +158,8 @@
- };
-
- partition at 100000 {
-- label = "uImage";
-- reg = <0x0100000 0x400000>;
-- };
--
-- partition at 500000 {
-- label = "pogoplug";
-- reg = <0x0500000 0x2000000>;
-- };
--
-- partition at 2500000 {
-- label = "root";
-- reg = <0x02500000 0xd800000>;
-+ label = "ubi";
-+ reg = <0x0100000 0x0ff00000>;
- };
- };
-
diff --git a/target/linux/kirkwood/patches-4.4/190-zyxel-nsa3xx-common-nand-partitions.patch b/target/linux/kirkwood/patches-4.4/190-zyxel-nsa3xx-common-nand-partitions.patch
deleted file mode 100644
index c8e15d4..0000000
--- a/target/linux/kirkwood/patches-4.4/190-zyxel-nsa3xx-common-nand-partitions.patch
+++ /dev/null
@@ -1,47 +0,0 @@
---- a/arch/arm/boot/dts/kirkwood-nsa3x0-common.dtsi
-+++ b/arch/arm/boot/dts/kirkwood-nsa3x0-common.dtsi
-@@ -121,39 +121,15 @@
-
- partition at 0 {
- label = "uboot";
-- reg = <0x0000000 0x0100000>;
-+ reg = <0x0000000 0x00c0000>;
- read-only;
- };
- partition at 100000 {
- label = "uboot_env";
-- reg = <0x0100000 0x0080000>;
-+ reg = <0x00c0000 0x0080000>;
- };
-- partition at 180000 {
-- label = "key_store";
-- reg = <0x0180000 0x0080000>;
-- };
-- partition at 200000 {
-- label = "info";
-- reg = <0x0200000 0x0080000>;
-- };
-- partition at 280000 {
-- label = "etc";
-- reg = <0x0280000 0x0a00000>;
-- };
-- partition at c80000 {
-- label = "kernel_1";
-- reg = <0x0c80000 0x0a00000>;
-- };
-- partition at 1680000 {
-- label = "rootfs1";
-- reg = <0x1680000 0x2fc0000>;
-- };
-- partition at 4640000 {
-- label = "kernel_2";
-- reg = <0x4640000 0x0a00000>;
-- };
-- partition at 5040000 {
-- label = "rootfs2";
-- reg = <0x5040000 0x2fc0000>;
-+ partition at 140000 {
-+ label = "ubi";
-+ reg = <0x0140000 0x7ec0000>;
- };
- };
diff --git a/target/linux/kirkwood/patches-4.4/191-nsa310b.patch b/target/linux/kirkwood/patches-4.4/191-nsa310b.patch
deleted file mode 100644
index b0afb8e..0000000
--- a/target/linux/kirkwood/patches-4.4/191-nsa310b.patch
+++ /dev/null
@@ -1,169 +0,0 @@
-kirkwood: add nsa310b dtb, a zyxel nsa310 variant
-
-add support to a nsa310 variant with red/green usb led
-and lm85 temp/fan controller
-
-Signed-off-by: Alberto Bursi <alberto.bursi at outlook.it>
-
-NOTE: this patch can be upstreamed as-is, LEDE-specific
- nand partitions are set in another patch
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -203,6 +203,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- kirkwood-ns2mini.dtb \
- kirkwood-nsa310.dtb \
- kirkwood-nsa310a.dtb \
-+ kirkwood-nsa310b.dtb \
- kirkwood-openblocks_a6.dtb \
- kirkwood-openblocks_a7.dtb \
- kirkwood-openrd-base.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-nsa310b.dts
-@@ -0,0 +1,146 @@
-+/dts-v1/;
-+
-+#include "kirkwood-nsa3x0-common.dtsi"
-+
-+/*
-+ * There are at least two different NSA310 designs. This variant has
-+ * a red/green USB Led (same as nsa310) and a lm85 temp/fan controller.
-+ */
-+
-+/ {
-+ model = "ZyXEL NSA310b";
-+ compatible = "zyxel,nsa310a", "zyxel,nsa310", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-+
-+ memory {
-+ device_type = "memory";
-+ reg = <0x00000000 0x10000000>;
-+ };
-+
-+ chosen {
-+ bootargs = "console=ttyS0,115200";
-+ stdout-path = "&uart0";
-+ };
-+
-+ mbus {
-+ pcie-controller {
-+ status = "okay";
-+
-+ pcie at 1,0 {
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ ocp at f1000000 {
-+ pinctrl: pin-controller at 10000 {
-+ pinctrl-0 = <&pmx_unknown>;
-+ pinctrl-names = "default";
-+
-+ pmx_led_esata_green: pmx-led-esata-green {
-+ marvell,pins = "mpp12";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_esata_red: pmx-led-esata-red {
-+ marvell,pins = "mpp13";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_usb_green: pmx-led-usb-green {
-+ marvell,pins = "mpp15";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_usb_red: pmx-led-usb-red {
-+ marvell,pins = "mpp16";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_sys_green: pmx-led-sys-green {
-+ marvell,pins = "mpp28";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_sys_red: pmx-led-sys-red {
-+ marvell,pins = "mpp29";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_hdd_green: pmx-led-hdd-green {
-+ marvell,pins = "mpp41";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_hdd_red: pmx-led-hdd-red {
-+ marvell,pins = "mpp42";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_unknown: pmx-unknown {
-+ marvell,pins = "mpp44";
-+ marvell,function = "gpio";
-+ };
-+
-+ };
-+
-+ i2c at 11000 {
-+ status = "okay";
-+
-+ lm85 at 2e {
-+ compatible = "national,lm85";
-+ reg = <0x2e>;
-+ };
-+ };
-+ };
-+
-+ gpio-leds {
-+ compatible = "gpio-leds";
-+ pinctrl-0 = <&pmx_led_esata_green &pmx_led_esata_red
-+ &pmx_led_usb_green &pmx_led_usb_red
-+ &pmx_led_sys_green &pmx_led_sys_red
-+ &pmx_led_copy_green &pmx_led_copy_red
-+ &pmx_led_hdd_green &pmx_led_hdd_red>;
-+ pinctrl-names = "default";
-+
-+ green-sys {
-+ label = "nsa310:green:sys";
-+ gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
-+ };
-+ red-sys {
-+ label = "nsa310:red:sys";
-+ gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
-+ };
-+ green-hdd {
-+ label = "nsa310:green:hdd";
-+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
-+ };
-+ red-hdd {
-+ label = "nsa310:red:hdd";
-+ gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
-+ };
-+ green-esata {
-+ label = "nsa310:green:esata";
-+ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
-+ };
-+ red-esata {
-+ label = "nsa310:red:esata";
-+ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
-+ };
-+ green-usb {
-+ label = "nsa310:green:usb";
-+ gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
-+ };
-+ red-usb {
-+ label = "nsa310:red:usb";
-+ gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
-+ };
-+ green-copy {
-+ label = "nsa310:green:copy";
-+ gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
-+ };
-+ red-copy {
-+ label = "nsa310:red:copy";
-+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
-+ };
-+ };
-+};
diff --git a/target/linux/kirkwood/patches-4.4/192-nsa310s.patch b/target/linux/kirkwood/patches-4.4/192-nsa310s.patch
deleted file mode 100644
index e78e680..0000000
--- a/target/linux/kirkwood/patches-4.4/192-nsa310s.patch
+++ /dev/null
@@ -1,300 +0,0 @@
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -204,6 +204,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- kirkwood-nsa310.dtb \
- kirkwood-nsa310a.dtb \
- kirkwood-nsa310b.dtb \
-+ kirkwood-nsa310s.dtb \
- kirkwood-openblocks_a6.dtb \
- kirkwood-openblocks_a7.dtb \
- kirkwood-openrd-base.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-nsa310s.dts
-@@ -0,0 +1,287 @@
-+/dts-v1/;
-+
-+#include "kirkwood.dtsi"
-+#include "kirkwood-6281.dtsi"
-+
-+/ {
-+ model = "ZyXEL NSA310S";
-+ compatible = "zyxel,nsa320s", "marvell,kirkwood-88f6702", "marvell,kirkwood";
-+
-+ memory {
-+ device_type = "memory";
-+ reg = <0x00000000 0x10000000>;
-+ };
-+
-+ chosen {
-+ bootargs = "console=ttyS0,115200n8 earlyprintk";
-+ stdout-path = &uart0;
-+ };
-+
-+ mbus {
-+ pcie-controller {
-+ status = "okay";
-+
-+ pcie at 1,0 {
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ ocp at f1000000 {
-+ pinctrl: pin-controller at 10000 {
-+ pinctrl-names = "default";
-+
-+ pmx_sata0: pmx-sata0 {
-+ marvell,pins;
-+ marvell,function = "sata0";
-+ };
-+ pmx_sata1: pmx-sata1 {
-+ marvell,pins;
-+ marvell,function = "sata1";
-+ };
-+ pmx_usb_power: pmx-usb-power {
-+ marvell,pins = "mpp21";
-+ marvell,function = "gpio";
-+ };
-+ pmx_pwr_off: pmx-pwr-off {
-+ marvell,pins = "mpp27";
-+ marvell,function = "gpio";
-+ };
-+ pmx_btn_reset: pmx-btn-reset {
-+ marvell,pins = "mpp24";
-+ marvell,function = "gpio";
-+ };
-+ pmx_btn_copy: pmx-btn-copy {
-+ marvell,pins = "mpp25";
-+ marvell,function = "gpio";
-+ };
-+ pmx_btn_power: pmx-btn-power {
-+ marvell,pins = "mpp26";
-+ marvell,function = "gpio";
-+ };
-+ pmx_led_hdd2_green: pmx-led-hdd2-green {
-+ marvell,pins = "mpp34";
-+ marvell,function = "gpio";
-+ };
-+ pmx_led_hdd2_red: pmx-led-hdd2-red {
-+ marvell,pins = "mpp12";
-+ marvell,function = "gpio";
-+ };
-+ pmx_led_usb_green: pmx-led-usb-green {
-+ marvell,pins = "mpp15";
-+ marvell,function = "gpio";
-+ };
-+ pmx_led_copy_green: pmx-led-copy-green {
-+ marvell,pins = "mpp22";
-+ marvell,function = "gpio";
-+ };
-+ pmx_led_copy_red: pmx-led-copy-red {
-+ marvell,pins = "mpp23";
-+ marvell,function = "gpio";
-+ };
-+ pmx_led_sys_green: pmx-led-sys-green {
-+ marvell,pins = "mpp28";
-+ marvell,function = "gpio";
-+ };
-+ pmx_led_sys_orange: pmx-led-sys-orange {
-+ marvell,pins = "mpp29";
-+ marvell,function = "gpio";
-+ };
-+ pmx_led_hdd1_green: pmx-led-hdd1-green {
-+ marvell,pins = "mpp16";
-+ marvell,function = "gpio";
-+ };
-+ pmx_led_hdd1_red: pmx-led-hdd1-red {
-+ marvell,pins = "mpp13";
-+ marvell,function = "gpio";
-+ };
-+ pmx_pwr_sata1: pmx-pwr-sata1 {
-+ marvell,pins = "mpp33";
-+ marvell,function = "gpio";
-+ };
-+ };
-+
-+ serial at 12000 {
-+ status = "okay";
-+ };
-+
-+ sata at 80000 {
-+ status = "okay";
-+ nr-ports = <2>;
-+ };
-+
-+ rtc at 10300 {
-+ status = "disabled";
-+ };
-+
-+ i2c at 11000 {
-+ status = "okay";
-+ ht1382: rtc at 68 {
-+ compatible = "htk,ht1382";
-+ reg = <0x68>;
-+ };
-+ };
-+ };
-+
-+ regulators {
-+ compatible = "simple-bus";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pmx_usb_power &pmx_pwr_sata1>;
-+
-+ usb0_power: regulator at 1 {
-+ compatible = "regulator-fixed";
-+ reg = <1>;
-+ regulator-name = "USB Power";
-+ regulator-min-microvolt = <5000000>;
-+ regulator-max-microvolt = <5000000>;
-+ regulator-always-on;
-+ regulator-boot-on;
-+ enable-active-high;
-+ gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ sata1_power: regulator at 2 {
-+ compatible = "regulator-fixed";
-+ reg = <2>;
-+ regulator-name = "SATA1 Power";
-+ regulator-min-microvolt = <5000000>;
-+ regulator-max-microvolt = <5000000>;
-+ regulator-always-on;
-+ regulator-boot-on;
-+ enable-active-high;
-+ gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>;
-+ };
-+ };
-+
-+
-+ gpio_keys {
-+ compatible = "gpio-keys";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ pinctrl-0 = <&pmx_btn_reset &pmx_btn_copy &pmx_btn_power>;
-+ pinctrl-names = "default";
-+
-+ button at 1 {
-+ label = "Power Button";
-+ linux,code = <KEY_POWER>;
-+ gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
-+ };
-+ button at 2 {
-+ label = "Copy Button";
-+ linux,code = <KEY_COPY>;
-+ gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
-+ };
-+ button at 3 {
-+ label = "Reset Button";
-+ linux,code = <KEY_RESTART>;
-+ gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
-+ };
-+ };
-+
-+ gpio-leds {
-+ compatible = "gpio-leds";
-+ pinctrl-0 = <&pmx_led_hdd2_green &pmx_led_hdd2_red
-+ &pmx_led_usb_green
-+ &pmx_led_sys_green &pmx_led_sys_orange
-+ &pmx_led_copy_green &pmx_led_copy_red
-+ &pmx_led_hdd1_green &pmx_led_hdd1_red>;
-+ pinctrl-names = "default";
-+
-+ green-sys {
-+ label = "nsa310s:green:sys";
-+ gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
-+ linux,default-trigger = "timer";
-+ };
-+ orange-sys {
-+ label = "nsa310s:orange:sys";
-+ gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
-+ };
-+ green-hdd1 {
-+ label = "nsa310s:green:hdd1";
-+ gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
-+ };
-+ red-hdd1 {
-+ label = "nsa310s:red:hdd1";
-+ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
-+ };
-+ green-hdd2 {
-+ label = "nsa310s:green:hdd2";
-+ gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
-+ };
-+ red-hdd2 {
-+ label = "nsa310s:red:hdd2";
-+ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
-+ };
-+ green-usb {
-+ label = "nsa310s:green:usb";
-+ gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
-+ };
-+ green-copy {
-+ label = "nsa310s:green:copy";
-+ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
-+ linux,default-trigger = "ide-disk";
-+ };
-+ red-copy {
-+ label = "nsa310s:red:copy";
-+ gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
-+ };
-+ };
-+
-+ gpio_poweroff {
-+ compatible = "gpio-poweroff";
-+ pinctrl-0 = <&pmx_pwr_off>;
-+ pinctrl-names = "default";
-+ gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>;
-+ };
-+};
-+
-+&nand {
-+ status = "okay";
-+ chip-delay = <35>;
-+
-+ partition at 0 {
-+ label = "u-boot";
-+ reg = <0x0000000 0xe0000>;
-+ };
-+
-+ partition at e0000 {
-+ label = "u-boot environment";
-+ reg = <0xe0000 0x100000>;
-+ };
-+
-+ partition at 100000 {
-+ label = "second stage u-boot";
-+ reg = <0x100000 0x200000>;
-+ };
-+
-+ partition at 200000 {
-+ label = "ubi";
-+ reg = <0x200000 0x7e00000>;
-+ };
-+};
-+
-+&mdio {
-+ status = "okay";
-+ ethphy0: ethernet-phy at 1 {
-+ compatible = "marvell,88e1318s";
-+ reg = <1>;
-+ marvell,reg-init = <0x1 0x16 0x0 0x3>,
-+ <0x1 0x10 0x0 0x1017>,
-+ <0x1 0x11 0x0 0x4408>,
-+ <0x1 0x16 0x0 0x0>,
-+ <0x1 0x4 0x0 0x1e1>,
-+ <0x1 0x9 0x0 0x300>,
-+ <0x1 0x10 0x0 0x3860>,
-+ <0x1 0x0 0x0 0x9140>;
-+ };
-+};
-+
-+ð0 {
-+ status = "okay";
-+
-+ ethernet0-port at 0 {
-+ phy-handle = <ðphy0>;
-+ };
-+};
diff --git a/target/linux/kirkwood/patches-4.4/194-nsa325.patch b/target/linux/kirkwood/patches-4.4/194-nsa325.patch
deleted file mode 100644
index e187374..0000000
--- a/target/linux/kirkwood/patches-4.4/194-nsa325.patch
+++ /dev/null
@@ -1,233 +0,0 @@
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -205,6 +205,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- kirkwood-nsa310a.dtb \
- kirkwood-nsa310b.dtb \
- kirkwood-nsa310s.dtb \
-+ kirkwood-nsa325.dtb \
- kirkwood-openblocks_a6.dtb \
- kirkwood-openblocks_a7.dtb \
- kirkwood-openrd-base.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-nsa325.dts
-@@ -0,0 +1,220 @@
-+/*
-+ * Device tree file for Zyxel NSA325 and NSA325v2 NAS
-+ */
-+/dts-v1/;
-+#include "kirkwood-nsa3x0-common.dtsi"
-+
-+/ {
-+ model = "ZyXEL NSA325";
-+ compatible = "zyxel,nsa325", "marvell,kirkwood-88f6282", "marvell,kirkwood";
-+
-+ memory {
-+ device_type = "memory";
-+ reg = <0x00000000 0x20000000>;
-+ };
-+
-+ chosen {
-+ bootargs = "console=ttyS0,115200";
-+ stdout-path = &uart0;
-+ };
-+
-+ mbus {
-+ pcie-controller {
-+ status = "okay";
-+
-+ pcie at 1,0 {
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ ocp at f1000000 {
-+ pinctrl: pin-controller at 10000 {
-+ pinctrl-names = "default";
-+
-+ pmx_led_sata2_green: pmx-led-sata2-green {
-+ marvell,pins = "mpp12";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_sata2_red: pmx-led-sata2-red {
-+ marvell,pins = "mpp13";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_mcu_data: pmx-mcu-data {
-+ marvell,pins = "mpp14";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_usb_green: pmx-led-usb-green {
-+ marvell,pins = "mpp15";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_mcu_clk: pmx-mcu-clk {
-+ marvell,pins = "mpp16";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_mcu_act: pmx-mcu-act {
-+ marvell,pins = "mpp17";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_usb_power_off: pmx-usb-power-off {
-+ marvell,pins = "mpp21";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_sys_green: pmx-led-sys-green {
-+ marvell,pins = "mpp28";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_sys_orange: pmx-led-sys-orange {
-+ marvell,pins = "mpp29";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_sata1_green: pmx-led-sata1-green {
-+ marvell,pins = "mpp41";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_sata1_red: pmx-led-sata1-red {
-+ marvell,pins = "mpp42";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_beeper: pmx-beeper {
-+ marvell,pins = "mpp44";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_pwr_sata1: pmx-pwr-sata1 {
-+ marvell,pins = "mpp47";
-+ marvell,function = "gpio";
-+ };
-+
-+ };
-+
-+ /* This board uses the pcf8563 RTC instead of the SoC RTC */
-+ rtc at 10300 {
-+ status = "disabled";
-+ };
-+
-+ i2c at 11000 {
-+ status = "okay";
-+
-+ pcf8563: pcf8563 at 51 {
-+ compatible = "nxp,pcf8563";
-+ reg = <0x51>;
-+ };
-+ };
-+
-+ };
-+
-+ gpio-leds {
-+ compatible = "gpio-leds";
-+ pinctrl-0 = <&pmx_led_sata1_green &pmx_led_sata1_red
-+ &pmx_led_sata2_green &pmx_led_sata2_red
-+ &pmx_led_sys_green &pmx_led_sys_orange
-+ &pmx_led_copy_green &pmx_led_copy_red
-+ &pmx_led_usb_green>;
-+ pinctrl-names = "default";
-+
-+ green-sata2 {
-+ label = "nsa325:green:sata2";
-+ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ red-sata2 {
-+ label = "nsa325:red:sata2";
-+ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ green-usb {
-+ label = "nsa325:green:usb";
-+ gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ green-sys {
-+ label = "nsa325:green:sys";
-+ gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ orange-sys {
-+ label = "nsa325:orange:sys";
-+ gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ green-copy {
-+ label = "nsa325:green:copy";
-+ gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ red-copy {
-+ label = "nsa325:red:copy";
-+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ green-sata1 {
-+ label = "nsa325:green:sata1";
-+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ red-sata1 {
-+ label = "nsa325:red:sata1";
-+ gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
-+ };
-+ };
-+
-+ regulators {
-+ compatible = "simple-bus";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ pinctrl-0 = <&pmx_usb_power_off &pmx_pwr_sata1>;
-+ pinctrl-names = "default";
-+
-+ usb_power: regulator at 1 {
-+ compatible = "regulator-fixed";
-+ reg = <1>;
-+ regulator-name = "USB Power";
-+ regulator-min-microvolt = <5000000>;
-+ regulator-max-microvolt = <5000000>;
-+ regulator-always-on;
-+ regulator-boot-on;
-+ enable-active-high;
-+ gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>;
-+ };
-+
-+ sata1_power: regulator at 2 {
-+ compatible = "regulator-fixed";
-+ reg = <2>;
-+ regulator-name = "SATA Power";
-+ regulator-min-microvolt = <5000000>;
-+ regulator-max-microvolt = <5000000>;
-+ regulator-always-on;
-+ regulator-boot-on;
-+ enable-active-high;
-+ gpio = <&gpio1 15 GPIO_ACTIVE_HIGH>;
-+ };
-+ };
-+};
-+
-+&mdio {
-+ status = "okay";
-+
-+ ethphy0: ethernet-phy at 1 {
-+ reg = <1>;
-+ };
-+};
-+
-+ð0 {
-+ status = "okay";
-+
-+ ethernet0-port at 0 {
-+ phy-handle = <ðphy0>;
-+ };
-+};
diff --git a/target/linux/kirkwood/patches-4.4/195-on100.patch b/target/linux/kirkwood/patches-4.4/195-on100.patch
deleted file mode 100644
index 8c66f2d..0000000
--- a/target/linux/kirkwood/patches-4.4/195-on100.patch
+++ /dev/null
@@ -1,173 +0,0 @@
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-on100.dts
-@@ -0,0 +1,160 @@
-+/dts-v1/;
-+
-+#include "kirkwood.dtsi"
-+#include "kirkwood-6282.dtsi"
-+
-+/ {
-+ model = "Cisco Systems ON100";
-+ compatible = "cisco,on100", "marvell,kirkwood-88f6282", "marvell,kirkwood";
-+
-+ memory {
-+ device_type = "memory";
-+ reg = <0x00000000 0x20000000>;
-+ };
-+
-+ aliases {
-+ serial0 = &uart0;
-+ };
-+
-+ chosen {
-+ bootargs = "console=ttyS0,115200n8 earlyprintk";
-+ stdout-path = "serial0:115200n8";
-+ };
-+
-+ gpio_keys {
-+ compatible = "gpio-keys";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ pinctrl-0 = <&pmx_btn_reset>;
-+ pinctrl-names = "default";
-+
-+ button at 1 {
-+ label = "Reset Button";
-+ linux,code = <KEY_RESTART>;
-+ gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
-+ };
-+ };
-+
-+ gpio-leds {
-+ compatible = "gpio-leds";
-+ pinctrl-0 = < &pmx_led_health_r &pmx_led_health_g >;
-+ pinctrl-names = "default";
-+
-+ health-g {
-+ label = "on100:green:health";
-+ gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
-+ };
-+
-+ health-r {
-+ label = "on100:red:health";
-+ gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
-+ };
-+
-+ health2-g {
-+ label = "on100:green:health2";
-+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
-+ };
-+
-+ health2-r {
-+ label = "on100:red:health2";
-+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
-+ };
-+ };
-+};
-+
-+ð0 {
-+ status = "okay";
-+
-+ ethernet0-port at 0 {
-+ phy-handle = <ðphy0>;
-+ phy-connection-type = "rgmii-id";
-+ };
-+};
-+
-+ð1 {
-+ status = "okay";
-+
-+ ethernet1-port at 0 {
-+ phy-handle = <ðphy1>;
-+ phy-connection-type = "rgmii-id";
-+ };
-+};
-+
-+&mdio {
-+ status = "okay";
-+
-+ ethphy0: ethernet-phy at 0 {
-+ /* Marvell 88E1121R */
-+ compatible = "ethernet-phy-id0141.0cb0",
-+ "ethernet-phy-ieee802.3-c22";
-+ reg = <0>;
-+ };
-+
-+ ethphy1: ethernet-phy at 1 {
-+ /* Marvell 88E1121R */
-+ compatible = "ethernet-phy-id0141.0cb0",
-+ "ethernet-phy-ieee802.3-c22";
-+ reg = <1>;
-+ };
-+};
-+
-+&nand {
-+ status = "okay";
-+
-+ partition at 0 {
-+ label = "u-boot";
-+ reg = <0x00000000 0x000a0000>;
-+ read-only;
-+ };
-+
-+ partition at a0000 {
-+ label = "u-boot environment";
-+ reg = <0x000a0000 0x00020000>;
-+ read-only;
-+ };
-+
-+ partition at c0000 {
-+ label = "kernel";
-+ reg = <0x000c0000 0x00540000>;
-+ };
-+
-+ partition at 600000 {
-+ label = "ubi";
-+ reg = <0x00600000 0x1fa00000>;
-+ };
-+};
-+
-+&pinctrl {
-+ pmx_led_health_r: pmx-led-health-r {
-+ marvell,pins = "mpp45";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_health_g: pmx-led-health-g {
-+ marvell,pins = "mpp44";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_health2_r: pmx-led-health2-r {
-+ marvell,pins = "mpp47";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_health2_g: pmx-led-health2-g {
-+ marvell,pins = "mpp46";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_btn_reset: pmx-led-reset {
-+ marvell,pins = "mpp31";
-+ marvell,function = "gpio";
-+ };
-+};
-+
-+&sdio {
-+ status = "okay";
-+};
-+
-+&uart0 {
-+ status = "okay";
-+};
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -206,6 +206,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- kirkwood-nsa310b.dtb \
- kirkwood-nsa310s.dtb \
- kirkwood-nsa325.dtb \
-+ kirkwood-on100.dtb \
- kirkwood-openblocks_a6.dtb \
- kirkwood-openblocks_a7.dtb \
- kirkwood-openrd-base.dtb \
diff --git a/target/linux/kirkwood/patches-4.4/200-disable-tso.patch b/target/linux/kirkwood/patches-4.4/200-disable-tso.patch
deleted file mode 100644
index af6ec20..0000000
--- a/target/linux/kirkwood/patches-4.4/200-disable-tso.patch
+++ /dev/null
@@ -1,35 +0,0 @@
-From: Ezequiel Garcia <ezequiel.garcia at free-electrons.com>
-Subject: [PATCH] net: mv643xx_eth: Make TSO disabled by default
-
-Data corruption has been observed to be produced by TSO. For instance,
-accessing files on a NFS-server with TSO enabled results in different data
-transferred each time.
-
-This has been observed only on Kirkwood platforms, i.e. with the mv643xx_eth
-driver. Same tests on platforms using the mvneta ethernet driver have
-passed without errors.
-
-Make TSO disabled by default for now, until we can found a proper fix
-for the regression.
-
-Fixes: 3ae8f4e0b98 ('net: mv643xx_eth: Implement software TSO')
-Reported-by: Slawomir Gajzner <slawomir.gajzner <at> gmail.com>
-Reported-by: Julien D'Ascenzio <jdascenzio <at> yahoo.fr>
-Signed-off-by: Ezequiel Garcia <ezequiel.garcia <at> free-electrons.com>
----
---- a/drivers/net/ethernet/marvell/mv643xx_eth.c
-+++ b/drivers/net/ethernet/marvell/mv643xx_eth.c
-@@ -3178,11 +3178,11 @@ static int mv643xx_eth_probe(struct plat
- dev->watchdog_timeo = 2 * HZ;
- dev->base_addr = 0;
-
-- dev->features = NETIF_F_SG | NETIF_F_IP_CSUM | NETIF_F_TSO;
-+ dev->features = NETIF_F_SG | NETIF_F_IP_CSUM;
- dev->vlan_features = dev->features;
-
- dev->features |= NETIF_F_RXCSUM;
-- dev->hw_features = dev->features;
-+ dev->hw_features = dev->features | NETIF_F_TSO;
-
- dev->priv_flags |= IFF_UNICAST_FLT;
- dev->gso_max_segs = MV643XX_MAX_TSO_SEGS;
diff --git a/target/linux/kirkwood/patches-4.4/210-enable-sata-port-specific-led-triggers.patch b/target/linux/kirkwood/patches-4.4/210-enable-sata-port-specific-led-triggers.patch
deleted file mode 100644
index 96c4f7b..0000000
--- a/target/linux/kirkwood/patches-4.4/210-enable-sata-port-specific-led-triggers.patch
+++ /dev/null
@@ -1,10 +0,0 @@
---- a/arch/arm/mach-mvebu/Kconfig
-+++ b/arch/arm/mach-mvebu/Kconfig
-@@ -105,6 +105,7 @@ config MACH_DOVE
- config MACH_KIRKWOOD
- bool "Marvell Kirkwood boards" if ARCH_MULTI_V5
- select ARCH_REQUIRE_GPIOLIB
-+ select ARCH_WANT_LIBATA_LEDS
- select CPU_FEROCEON
- select KIRKWOOD_CLK
- select MACH_MVEBU_ANY
More information about the lede-commits
mailing list