[source] uboot-kirkwood: add uboot for nsa310b
LEDE Commits
lede-commits at lists.infradead.org
Tue Jan 24 07:21:47 PST 2017
nbd pushed a commit to source.git, branch master:
https://git.lede-project.org/3d1b2b22d6d27f9da64d159743fd77ee7265eee9
commit 3d1b2b22d6d27f9da64d159743fd77ee7265eee9
Author: Alberto Bursi <alberto.bursi at outlook.it>
AuthorDate: Sun Jan 22 14:43:51 2017 +0100
uboot-kirkwood: add uboot for nsa310b
this commit allows to make a standalone u-boot for nsa310b.
While both first-stage and second-stage u-boot work fine if
installed to flash or loaded with kwboot,
I could not get stock u-boot nor bodhi's u-boot to chainload
any second stage u-boot (I also tried with dockstar's uboot
that works fine on this device if loaded with kwboot).
Signed-off-by: Alberto Bursi <alberto.bursi at outlook.it>
---
package/boot/uboot-kirkwood/Makefile | 5 +
.../patches/007-nsa310-uboot-generic.patch | 722 +++++++++++++++++++++
.../patches/200-openwrt-config.patch | 27 +-
3 files changed, 745 insertions(+), 9 deletions(-)
diff --git a/package/boot/uboot-kirkwood/Makefile b/package/boot/uboot-kirkwood/Makefile
index 74b9f0f..c42f947 100644
--- a/package/boot/uboot-kirkwood/Makefile
+++ b/package/boot/uboot-kirkwood/Makefile
@@ -58,6 +58,10 @@ define uboot/iconnect_second_stage
TITLE:=second stage U-Boot for Iomega iConnect Wireless
endef
+define uboot/nsa310
+ TITLE:=U-Boot for Zyxel NSA310
+endef
+
define uboot/pogo_e02
TITLE:=U-Boot for Cloud Engines Pogoplug E02
endef
@@ -75,6 +79,7 @@ UBOOTS:= \
goflexhome \
ib62x0 ib62x0_second_stage \
iconnect iconnect_second_stage \
+ nsa310 \
pogo_e02 pogo_e02_second_stage \
sheevaplug
diff --git a/package/boot/uboot-kirkwood/patches/007-nsa310-uboot-generic.patch b/package/boot/uboot-kirkwood/patches/007-nsa310-uboot-generic.patch
new file mode 100644
index 0000000..b9fb78d
--- /dev/null
+++ b/package/boot/uboot-kirkwood/patches/007-nsa310-uboot-generic.patch
@@ -0,0 +1,722 @@
+arm: kirkwood: add ZyXEL NSA310 device
+
+This patch add ZyXEL NSA310 1-Bay Media Server
+
+The ZyXEL NSA310 device is a Kirkwood based NAS:
+
+- SoC: Marvell 88F6702 1200Mhz
+- SDRAM memory: 256MB DDR2 400Mhz
+- Gigabit ethernet: PHY Realtek
+- Flash memory: 128MB
+- 1 Power button
+- 1 Power LED (blue)
+- 5 Status LED (green/red)
+- 1 Copy/Sync button
+- 1 Reset button
+- 2 SATA II port (1 internal and 1 external eSata)
+- 2 USB 2.0 ports (1 front and 1 back)
+- Smart fan
+
+Signed-off-by: Alberto Bursi <alberto.bursi at outlook.it>
+
+NOTE: this patch is ready for upstream, LEDE-specific parts are in
+ another patch
+
+diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
+index 9205b1e..819bd3b 100644
+--- a/arch/arm/mach-kirkwood/Kconfig
++++ b/arch/arm/mach-kirkwood/Kconfig
+@@ -49,6 +49,9 @@ config TARGET_GOFLEXHOME
+ config TARGET_NAS220
+ bool "BlackArmor NAS220"
+
++config TARGET_NSA310
++ bool "Zyxel NSA310 Board"
++
+ config TARGET_NSA310S
+ bool "Zyxel NSA310S"
+
+@@ -72,6 +75,7 @@ source "board/raidsonic/ib62x0/Kconfig"
+ source "board/Seagate/dockstar/Kconfig"
+ source "board/Seagate/goflexhome/Kconfig"
+ source "board/Seagate/nas220/Kconfig"
++source "board/zyxel/nsa310/Kconfig"
+ source "board/zyxel/nsa310s/Kconfig"
+
+ endif
+diff --git a/board/zyxel/nsa310/Kconfig b/board/zyxel/nsa310/Kconfig
+new file mode 100644
+index 0000000..145ade6
+--- /dev/null
++++ b/board/zyxel/nsa310/Kconfig
+@@ -0,0 +1,12 @@
++if TARGET_NSA310
++
++config SYS_BOARD
++ default "nsa310"
++
++config SYS_VENDOR
++ default "zyxel"
++
++config SYS_CONFIG_NAME
++ default "nsa310"
++
++endif
+diff --git a/board/zyxel/nsa310/MAINTAINERS b/board/zyxel/nsa310/MAINTAINERS
+new file mode 100644
+index 0000000..d09f1ab
+--- /dev/null
++++ b/board/zyxel/nsa310/MAINTAINERS
+@@ -0,0 +1,6 @@
++NSA310 BOARD
++M: Alberto Bursi <alberto.bursi at outlook.it>
++S: Maintained
++F: board/zyxel/nsa310/
++F: include/configs/nsa310.h
++F: configs/nsa310_defconfig
+diff --git a/board/zyxel/nsa310/Makefile b/board/zyxel/nsa310/Makefile
+new file mode 100644
+index 0000000..dfe93cc
+--- /dev/null
++++ b/board/zyxel/nsa310/Makefile
+@@ -0,0 +1,12 @@
++#
++# (C) Copyright 2015 bodhi <mibodhi at gmail.com>
++#
++# Based on
++# (C) Copyright 2009
++# Marvell Semiconductor <www.marvell.com>
++# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
++#
++# SPDX-License-Identifier: GPL-2.0+
++#
++
++obj-y := nsa310.o
+diff --git a/board/zyxel/nsa310/kwbimage.cfg b/board/zyxel/nsa310/kwbimage.cfg
+new file mode 100644
+index 0000000..f60e1d2
+--- /dev/null
++++ b/board/zyxel/nsa310/kwbimage.cfg
+@@ -0,0 +1,166 @@
++#
++# Copyright (C) 2013 Rafal Kazmierowski
++#
++# Based on guruplug.c originally written by
++# Siddarth Gore <gores at marvell.com>
++# (C) Copyright 2009
++# Marvell Semiconductor <www.marvell.com>
++#
++# See file CREDITS for list of people who contributed to this
++# project.
++#
++# This program is free software; you can redistribute it and/or
++# modify it under the terms of the GNU General Public License as
++# published by the Free Software Foundation; either version 2 of
++# the License, or (at your option) any later version.
++#
++# This program is distributed in the hope that it will be useful,
++# but WITHOUT ANY WARRANTY; without even the implied warranty of
++# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++# GNU General Public License for more details.
++#
++# You should have received a copy of the GNU General Public License
++# along with this program; if not, write to the Free Software
++# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
++# MA 02110-1301 USA
++#
++# Refer docs/README.kwimage for more details about how-to configure
++# and create kirkwood boot image
++#
++
++# Boot Media configurations
++BOOT_FROM nand
++#BOOT_FROM uart
++NAND_ECC_MODE default
++NAND_PAGE_SIZE 0x0800
++
++# SOC registers configuration using bootrom header extension
++# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
++
++# Configure RGMII-0 interface pad voltage to 1.8V
++DATA 0xFFD100e0 0x1b1b1b9b
++
++#Dram initalization for SINGLE x16 CL=5 @ 400MHz
++DATA 0xFFD01400 0x43010c30 # DDR Configuration register
++# bit13-0: 0xc30 (3120 DDR2 clks refresh rate)
++# bit23-14: zero
++# bit24: 1= enable exit self refresh mode on DDR access
++# bit25: 1 required
++# bit29-26: zero
++# bit31-30: 01
++
++DATA 0xFFD01404 0x37543000 # DDR Controller Control Low
++# bit 4: 0=addr/cmd in smame cycle
++# bit 5: 0=clk is driven during self refresh, we don't care for APX
++# bit 6: 0=use recommended falling edge of clk for addr/cmd
++# bit14: 0=input buffer always powered up
++# bit18: 1=cpu lock transaction enabled
++# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
++# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
++# bit30-28: 3 required
++# bit31: 0=no additional STARTBURST delay
++
++DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
++# bit3-0: TRAS lsbs
++# bit7-4: TRCD
++# bit11- 8: TRP
++# bit15-12: TWR
++# bit19-16: TWTR
++# bit20: TRAS msb
++# bit23-21: 0x0
++# bit27-24: TRRD
++# bit31-28: TRTP
++
++DATA 0xFFD0140C 0x00000a33 # DDR Timing (High)
++# bit6-0: TRFC
++# bit8-7: TR2R
++# bit10-9: TR2W
++# bit12-11: TW2W
++# bit31-13: zero required
++
++DATA 0xFFD01410 0x0000000c # DDR Address Control
++# bit1-0: 01, Cs0width=x8
++# bit3-2: 10, Cs0size=1Gb
++# bit5-4: 01, Cs1width=x8
++# bit7-6: 10, Cs1size=1Gb
++# bit9-8: 00, Cs2width=nonexistent
++# bit11-10: 00, Cs2size =nonexistent
++# bit13-12: 00, Cs3width=nonexistent
++# bit15-14: 00, Cs3size =nonexistent
++# bit16: 0, Cs0AddrSel
++# bit17: 0, Cs1AddrSel
++# bit18: 0, Cs2AddrSel
++# bit19: 0, Cs3AddrSel
++# bit31-20: 0 required
++
++DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
++# bit0: 0, OpenPage enabled
++# bit31-1: 0 required
++
++DATA 0xFFD01418 0x00000000 # DDR Operation
++# bit3-0: 0x0, DDR cmd
++# bit31-4: 0 required
++
++DATA 0xFFD0141C 0x00000652 # DDR Mode
++# bit2-0: 2, BurstLen=2 required
++# bit3: 0, BurstType=0 required
++# bit6-4: 4, CL=5
++# bit7: 0, TestMode=0 normal
++# bit8: 0, DLL reset=0 normal
++# bit11-9: 6, auto-precharge write recovery ????????????
++# bit12: 0, PD must be zero
++# bit31-13: 0 required
++
++DATA 0xFFD01420 0x00000004 # DDR Extended Mode
++# bit0: 0, DDR DLL enabled
++# bit1: 0, DDR drive strenght normal
++# bit2: 0, DDR ODT control lsd (disabled)
++# bit5-3: 000, required
++# bit6: 1, DDR ODT control msb, (disabled)
++# bit9-7: 000, required
++# bit10: 0, differential DQS enabled
++# bit11: 0, required
++# bit12: 0, DDR output buffer enabled
++# bit31-13: 0 required
++
++DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
++# bit2-0: 111, required
++# bit3 : 1 , MBUS Burst Chop disabled
++# bit6-4: 111, required
++# bit7 : 0
++# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
++# bit9 : 0 , no half clock cycle addition to dataout
++# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
++# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
++# bit15-12: 1111 required
++# bit31-16: 0 required
++
++DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
++DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
++
++
++DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
++#DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
++# bit0: 1, Window enabled
++# bit1: 0, Write Protect disabled
++# bit3-2: 00, CS0 hit selected
++# bit23-4: ones, required
++# bit31-24: 0x0F, Size (i.e. 256MB)
++
++DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb
++DATA 0xFFD0150C 0x00000000 # CS[2]n Size, window disabled KAZ z 400db
++DATA 0xFFD01514 0x00000000 # CS[3]n Size, window disabled
++
++DATA 0xFFD0151C 0x00000000 # DDR ODT Control (Low)
++DATA 0xFFD01494 0x00120012 # DDR ODT Control (High) KAZ z nowy STATIC_SDRAM_ODT_CTRL_LOW
++# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
++# bit3-2: 01, ODT1 active NEVER!
++# bit31-4: zero, required
++
++DATA 0xFFD01498 0x00000000 # CPU ODT Control KAZ STATIC_SDRAM_ODT_CTRL_HI
++DATA 0xFFD0149C 0x0000E403 # DDR Initialization Control KAZ STATIC_SDRAM_DUNIT_ODT_CTRL
++DATA 0xFFD01480 0x00000001 # DDR Initialization Control
++#bit0=1, enable DDR init upon this register write
++
++# End of Header extension
++DATA 0x0 0x0
+diff --git a/board/zyxel/nsa310/nsa310.c b/board/zyxel/nsa310/nsa310.c
+new file mode 100644
+index 0000000..eee3f1a
+--- /dev/null
++++ b/board/zyxel/nsa310/nsa310.c
+@@ -0,0 +1,190 @@
++/*
++ * Copyright (C) 2013 Rafal Kazmierowski
++ *
++ * Based on NSA320.c Peter Schildmann <linux at schildmann.info>
++ * originally written by
++ * Marvell Semiconductor <www.marvell.com>
++ * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
++ *
++ * See file CREDITS for list of people who contributed to this
++ * project.
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License as
++ * published by the Free Software Foundation; either version 2 of
++ * the License, or (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
++ * MA 02110-1301 USA
++ */
++
++#include <common.h>
++#include <miiphy.h>
++#include <asm/arch/cpu.h>
++#include <asm/arch/soc.h>
++#include <asm/arch/mpp.h>
++#include <asm/io.h>
++#include "nsa310.h"
++
++DECLARE_GLOBAL_DATA_PTR;
++
++int board_early_init_f(void)
++{
++ /*
++ * default gpio configuration
++ * There are maximum 64 gpios controlled through 2 sets of registers
++ * the below configuration configures mainly initial LED status
++ */
++ mvebu_config_gpio(NSA310_VAL_LOW, NSA310_VAL_HIGH,
++ NSA310_OE_LOW, NSA310_OE_HIGH);
++
++ /* Multi-Purpose Pins Functionality configuration */
++ /* (all LEDs & power off active high) */
++ static const u32 kwmpp_config[] = {
++ MPP0_NF_IO2,
++ MPP1_NF_IO3,
++ MPP2_NF_IO4,
++ MPP3_NF_IO5,
++ MPP4_NF_IO6,
++ MPP5_NF_IO7,
++ MPP6_SYSRST_OUTn,
++ MPP7_GPO,
++ MPP8_TW_SDA, /* PCF8563 RTC chip */
++ MPP9_TW_SCK, /* connected to TWSI */
++ MPP10_UART0_TXD,
++ MPP11_UART0_RXD,
++ MPP12_GPO, /* SATA2 LED (green) */
++ MPP13_GPIO, /* SATA2 LED (red) */
++ MPP14_GPIO, /* MCU DATA pin (in) */
++ MPP15_GPIO, /* USB LED (green) */
++ MPP16_GPIO, /* MCU CLK pin (out) */
++ MPP17_GPIO, /* MCU ACT pin (out) */
++ MPP18_NF_IO0,
++ MPP19_NF_IO1,
++ MPP20_GPIO,
++ MPP21_GPIO, /* USB LED (red)-Power*/
++ MPP22_GPIO,
++ MPP23_GPIO,
++ MPP24_GPIO,
++ MPP25_GPIO,
++ MPP26_GPIO,
++ MPP27_GPIO,
++ MPP28_GPIO, /* SYS LED (green) */
++ MPP29_GPIO, /* SYS LED (red) */
++ MPP30_GPIO,
++ MPP31_GPIO,
++ MPP32_GPIO,
++ MPP33_GPIO,
++ MPP34_GPIO,
++ MPP35_GPIO,
++ MPP36_GPIO, /* Reset button */
++ MPP37_GPIO, /* Copy button */
++ MPP38_GPIO, /* VID B0 */
++ MPP39_GPIO, /* COPY LED (green) */
++ MPP40_GPIO, /* COPY LED (red) */
++ MPP41_GPIO, /* SATA1 LED (green) */
++ MPP42_GPIO, /* SATA1 LED (red) */
++ MPP43_GPIO, /* HTP pin */
++ MPP44_GPIO, /* Buzzer */
++ MPP45_GPIO, /* VID B1 */
++ MPP46_GPIO, /* Power button */
++ MPP47_GPIO, /* Power resume data */
++ MPP48_GPIO, /* Power off */
++ MPP49_GPIO, /* Power resume clock */
++ 0
++ };
++ kirkwood_mpp_conf(kwmpp_config,NULL);
++ return 0;
++}
++
++int board_init(void)
++{
++ /* address of boot parameters */
++ gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
++
++ return 0;
++}
++
++#ifdef CONFIG_RESET_PHY_R
++/* Configure and enable MV88E1318 PHY */
++void reset_phy(void)
++{
++ u16 reg;
++ u16 devadr;
++ char *name = "egiga0";
++
++ if (miiphy_set_current_dev(name))
++ return;
++
++ /* command to read PHY dev address */
++ if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
++ printf("Err..%s could not read PHY dev address\n",
++ __FUNCTION__);
++ return;
++ }
++
++ /* Set RGMII delay */
++ miiphy_write(name, devadr, MV88E1318_PGADR_REG, 2);
++ miiphy_read(name, devadr, MV88E1318_MAC_CTRL_REG, ®);
++ reg |= (MV88E1318_RGMII_RXTM_CTRL | MV88E1318_RGMII_TXTM_CTRL);
++ miiphy_write(name, devadr, MV88E1318_MAC_CTRL_REG, reg);
++ miiphy_write(name, devadr, MV88E1318_PGADR_REG, 0);
++
++ /* reset the phy */
++ miiphy_reset(name, devadr);
++
++ printf("MV88E1318 PHY initialized on %s\n", name);
++}
++#endif /* CONFIG_RESET_PHY_R */
++
++#ifdef CONFIG_SHOW_BOOT_PROGRESS
++void show_boot_progress(int val)
++{
++ struct kwgpio_registers *gpio0 = (struct kwgpio_registers *)MVEBU_GPIO0_BASE;
++ u32 dout0 = readl(&gpio0->dout);
++ u32 blen0 = readl(&gpio0->blink_en);
++
++ struct kwgpio_registers *gpio1 = (struct kwgpio_registers *)MVEBU_GPIO1_BASE;
++ u32 dout1 = readl(&gpio1->dout);
++ u32 blen1 = readl(&gpio1->blink_en);
++
++ switch (val) {
++ case BOOTSTAGE_ID_DECOMP_IMAGE:
++ writel(blen0 & ~(SYS_GREEN_LED | SYS_RED_LED), &gpio0->blink_en);
++ writel((dout0 & ~SYS_GREEN_LED) | SYS_RED_LED, &gpio0->dout);
++ break;
++ case BOOTSTAGE_ID_RUN_OS:
++ writel(dout0 & ~SYS_RED_LED, &gpio0->dout);
++ writel(blen0 | SYS_GREEN_LED, &gpio0->blink_en);
++ break;
++ case BOOTSTAGE_ID_NET_START:
++ writel(dout1 & ~COPY_RED_LED, &gpio1->dout);
++ writel((blen1 & ~COPY_RED_LED) | COPY_GREEN_LED, &gpio1->blink_en);
++ break;
++ case BOOTSTAGE_ID_NET_LOADED:
++ writel(blen1 & ~(COPY_RED_LED | COPY_GREEN_LED), &gpio1->blink_en);
++ writel((dout1 & ~COPY_RED_LED) | COPY_GREEN_LED, &gpio1->dout);
++ break;
++ case -BOOTSTAGE_ID_NET_NETLOOP_OK:
++ case -BOOTSTAGE_ID_NET_LOADED:
++ writel(dout1 & ~COPY_GREEN_LED, &gpio1->dout);
++ writel((blen1 & ~COPY_GREEN_LED) | COPY_RED_LED, &gpio1->blink_en);
++ break;
++ default:
++ if (val < 0) {
++ /* error */
++ printf("Error occured, error code = %d\n", -val);
++ writel(dout0 & ~SYS_GREEN_LED, &gpio0->dout);
++ writel(blen0 | SYS_RED_LED, &gpio0->blink_en);
++ }
++ break;
++ }
++}
++#endif
+diff --git a/board/zyxel/nsa310/nsa310.h b/board/zyxel/nsa310/nsa310.h
+new file mode 100644
+index 0000000..6634a4f
+--- /dev/null
++++ b/board/zyxel/nsa310/nsa310.h
+@@ -0,0 +1,56 @@
++/*
++ * Copyright (C) 2013 Rafal Kazmierowski
++ *
++ * Based on Peter Schildmann <linux at schildmann.info>
++ * and guruplug.h originally written by
++ * Siddarth Gore <gores at marvell.com>
++ * (C) Copyright 2009
++ * Marvell Semiconductor <www.marvell.com>
++ *
++ * See file CREDITS for list of people who contributed to this
++ * project.
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License as
++ * published by the Free Software Foundation; either version 2 of
++ * the License, or (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
++ * MA 02110-1301 USA
++ */
++
++#ifndef __NSA310_H
++#define __NSA310_H
++
++/* GPIO's */
++#define SYS_GREEN_LED (1 << 28)
++#define SYS_RED_LED (1 << 29)
++#define SATA1_GREEN_LED (1 << 41)
++#define SATA1_RED_LED (1 << 42)
++#define SATA2_GREEN_LED (1 << 12)
++#define SATA2_RED_LED (1 << 13)
++#define USB_GREEN_LED (1 << 15)
++#define USB_RED_LED (1 << 21)
++#define COPY_GREEN_LED (1 << 39)
++#define COPY_RED_LED (1 << 40)
++
++#define NSA310_OE_LOW (0)
++#define NSA310_VAL_LOW (SYS_GREEN_LED)
++#define NSA310_OE_HIGH ((COPY_GREEN_LED | COPY_RED_LED | \
++ SATA1_GREEN_LED | SATA1_RED_LED))
++#define NSA310_VAL_HIGH (0)
++
++/* PHY related */
++#define MV88E1318_MAC_CTRL_REG 21
++#define MV88E1318_PGADR_REG 22
++#define MV88E1318_RGMII_TXTM_CTRL (1 << 4)
++#define MV88E1318_RGMII_RXTM_CTRL (1 << 5)
++
++#endif /* __NSA310_H */
+diff --git a/configs/nsa310_defconfig b/configs/nsa310_defconfig
+new file mode 100644
+index 0000000..d26ef35
+--- /dev/null
++++ b/configs/nsa310_defconfig
+@@ -0,0 +1,18 @@
++CONFIG_ARM=y
++CONFIG_KIRKWOOD=y
++CONFIG_TARGET_NSA310=y
++CONFIG_BOOTDELAY=3
++CONFIG_SYS_PROMPT="NSA310> "
++# CONFIG_CMD_IMLS is not set
++# CONFIG_CMD_FLASH is not set
++CONFIG_SYS_NS16550=y
++CONFIG_CMD_FDT=y
++CONFIG_OF_LIBFDT=y
++CONFIG_CMD_SETEXPR=y
++CONFIG_CMD_DHCP=y
++CONFIG_CMD_NAND=y
++CONFIG_CMD_PING=y
++CONFIG_CMD_USB=y
++CONFIG_CMD_EXT2=y
++CONFIG_CMD_FAT=y
++CONFIG_USB_STORAGE=y
+diff --git a/include/configs/nsa310.h b/include/configs/nsa310.h
+new file mode 100644
+index 0000000..86ef825
+--- /dev/null
++++ b/include/configs/nsa310.h
+@@ -0,0 +1,168 @@
++/* Copyright (C) 2015-2016 bodhi <mibodhi at gmail.com>
++ *
++ * Based on
++ * Copyright (C) 2012 Peter Schildmann <linux at schildmann.info>
++ *
++ * Based on guruplug.h originally written by
++ * Siddarth Gore <gores at marvell.com>
++ * (C) Copyright 2009
++ * Marvell Semiconductor <www.marvell.com>
++ *
++ * See file CREDITS for list of people who contributed to this
++ * project.
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License as
++ * published by the Free Software Foundation; either version 2 of
++ * the License, or (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
++ * MA 02110-1301 USA
++ */
++
++#ifndef _CONFIG_NSA310_H
++#define _CONFIG_NSA310_H
++
++/*
++ * Version number information
++ */
++
++#define CONFIG_IDENT_STRING "\nZyXEL NSA310 1-Bay Power Media Server \n"
++
++/*
++ * High Level Configuration Options (easy to change)
++ */
++#define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */
++#define CONFIG_KW88F6281 /* SOC Name */
++#define CONFIG_MACH_NSA310 /* Machine type */
++#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
++
++/*
++ * Misc Configuration Options
++ */
++#define CONFIG_SHOW_BOOT_PROGRESS 1 /* boot progess display (LED's) */
++
++/*
++ * Commands configuration
++ */
++#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
++#define CONFIG_SYS_MVFS /* Picks up Filesystem from mv-common.h */
++#define CONFIG_CMD_DHCP
++#define CONFIG_CMD_ENV
++#define CONFIG_CMD_IDE
++#define CONFIG_CMD_MII
++#define CONFIG_CMD_NAND
++#define CONFIG_CMD_PING
++#define CONFIG_CMD_USB
++#define CONFIG_CMD_DATE
++#define CONFIG_SYS_LONGHELP
++#define CONFIG_PREBOOT
++#define CONFIG_SYS_HUSH_PARSER
++#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
++
++/*
++ * mv-common.h should be defined after CMD configs since it used them
++ * to enable certain macros
++ */
++#include "mv-common.h"
++
++/* Remove or override few declarations from mv-common.h */
++#undef CONFIG_SYS_PROMPT /* previously defined in mv-common.h */
++#define CONFIG_SYS_PROMPT "NSA310> " /* Command Prompt */
++
++/*
++ * Environment variables configurations
++ */
++#ifdef CONFIG_CMD_NAND
++#define CONFIG_ENV_IS_IN_NAND 1
++#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
++#else
++#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */
++#endif
++
++/* max 4k env size is enough, but in case of nand
++ * it has to be rounded to sector size
++ */
++#define CONFIG_ENV_SIZE 0x20000 /* 128k */
++#define CONFIG_ENV_ADDR 0xc0000
++#define CONFIG_ENV_OFFSET 0xc0000 /* env starts here */
++
++/*
++ * Default environment variables
++ */
++#define CONFIG_BOOTCOMMAND \
++ "ubi part ubi; " \
++ "ubi read 0x800000 kernel; " \
++ "bootm 0x800000"
++
++#define CONFIG_MTDPARTS \
++ "mtdparts=orion_nand:" \
++ "0x0c0000(uboot)," \
++ "0x80000(uboot_env)," \
++ "0x7ec0000(ubi)\0"
++
++#define CONFIG_EXTRA_ENV_SETTINGS \
++ "console=console=ttyS0,115200\0" \
++ "mtdids=nand0=orion_nand\0" \
++ "mtdparts="CONFIG_MTDPARTS \
++ "bootargs_root=\0"
++
++/*
++ * Ethernet Driver configuration
++ */
++#ifdef CONFIG_CMD_NET
++#define CONFIG_NETCONSOLE
++#define CONFIG_NET_MULTI
++#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
++#define CONFIG_PHY_BASE_ADR 0x1
++#define CONFIG_PHY_GIGE
++#define CONFIG_RESET_PHY_R
++#endif /* CONFIG_CMD_NET */
++
++/*
++ * SATA Driver configuration
++ */
++#ifdef CONFIG_MVSATA_IDE
++#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
++#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET
++#endif /* CONFIG_MVSATA_IDE */
++
++/*
++ * File system
++ */
++#define CONFIG_CMD_EXT2
++#define CONFIG_CMD_EXT4
++#define CONFIG_CMD_FAT
++#define CONFIG_CMD_JFFS2
++#define CONFIG_JFFS2_NAND
++#define CONFIG_JFFS2_LZO
++#define CONFIG_CMD_UBI
++#define CONFIG_CMD_UBIFS
++#define CONFIG_RBTREE
++#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
++#define CONFIG_MTD_PARTITIONS
++#define CONFIG_CMD_MTDPARTS
++#define CONFIG_LZO
++
++/*
++ * EFI partition
++ */
++#define CONFIG_EFI_PARTITION
++
++/*
++ * Date Time
++ */
++#ifdef CONFIG_CMD_DATE
++#define CONFIG_RTC_MV
++#define CONFIG_CMD_SNTP
++#define CONFIG_CMD_DNS
++#endif /* CONFIG_CMD_DATE */
++
++#endif /* _CONFIG_NSA310_H */
diff --git a/package/boot/uboot-kirkwood/patches/200-openwrt-config.patch b/package/boot/uboot-kirkwood/patches/200-openwrt-config.patch
index 37f30d0..1f5dd84 100644
--- a/package/boot/uboot-kirkwood/patches/200-openwrt-config.patch
+++ b/package/boot/uboot-kirkwood/patches/200-openwrt-config.patch
@@ -1,9 +1,9 @@
--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
-@@ -74,4 +74,7 @@ source "board/Seagate/goflexhome/Kconfig
- source "board/Seagate/nas220/Kconfig"
+@@ -78,4 +78,7 @@ source "board/Seagate/nas220/Kconfig"
+ source "board/zyxel/nsa310/Kconfig"
source "board/zyxel/nsa310s/Kconfig"
-
+
+config SECOND_STAGE
+ bool "OpenWrt second stage hack"
+
@@ -13,7 +13,7 @@
@@ -98,4 +98,6 @@
#define CONFIG_CMD_MTDPARTS
#define CONFIG_LZO
-
+
+#include "openwrt-kirkwood-common.h"
+
#endif /* _CONFIG_DOCKSTAR_H */
@@ -22,7 +22,7 @@
@@ -108,4 +108,6 @@
#define CONFIG_RTC_MV
#endif /* CONFIG_CMD_DATE */
-
+
+#include "openwrt-kirkwood-common.h"
+
#endif /* _CONFIG_IB62x0_H */
@@ -31,7 +31,7 @@
@@ -103,4 +103,6 @@
#define CONFIG_MTD_PARTITIONS
#define CONFIG_CMD_MTDPARTS
-
+
+#include "openwrt-kirkwood-common.h"
+
#endif /* _CONFIG_ICONNECT_H */
@@ -83,7 +83,7 @@
@@ -99,4 +99,6 @@
#define CONFIG_CMD_MTDPARTS
#define CONFIG_LZO
-
+
+#include "openwrt-kirkwood-common.h"
+
#endif /* _CONFIG_POGO_E02_H */
@@ -92,7 +92,7 @@
@@ -109,4 +109,6 @@
#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET
#endif /* CONFIG_CMD_IDE */
-
+
+#include "openwrt-kirkwood-common.h"
+
#endif /* _CONFIG_SHEEVAPLUG_H */
@@ -101,7 +101,16 @@
@@ -122,4 +122,6 @@
#define CONFIG_RTC_MV
#endif /* CONFIG_CMD_DATE */
-
+
+#include "openwrt-kirkwood-common.h"
+
#endif /* _CONFIG_GOFLEXHOME_H */
+--- a/include/configs/nsa310.h
++++ b/include/configs/nsa310.h
+@@ -166,4 +166,6 @@
+ #define CONFIG_CMD_DNS
+ #endif /* CONFIG_CMD_DATE */
+
++#include "openwrt-kirkwood-common.h"
++
+ #endif /* _CONFIG_NSA310_H */
More information about the lede-commits
mailing list