[source] brcm2708: remove linux 4.4 support
LEDE Commits
lede-commits at lists.infradead.org
Tue Feb 7 14:19:32 PST 2017
noltari pushed a commit to source.git, branch master:
https://git.lede-project.org/d9d090e52082635a24aeaefdc6bfe61ab97f38bb
commit d9d090e52082635a24aeaefdc6bfe61ab97f38bb
Author: Álvaro Fernández Rojas <noltari at gmail.com>
AuthorDate: Tue Feb 7 22:30:59 2017 +0100
brcm2708: remove linux 4.4 support
Signed-off-by: Álvaro Fernández Rojas <noltari at gmail.com>
---
target/linux/brcm2708/bcm2708/config-4.4 | 364 -
target/linux/brcm2708/bcm2709/config-4.4 | 396 -
target/linux/brcm2708/bcm2710/config-4.4 | 391 -
...0001-smsx95xx-fix-crimes-against-truesize.patch | 33 -
...02-smsc95xx-Disable-turbo-mode-by-default.patch | 20 -
...around-for-issue-where-dirty-page-count-g.patch | 27 -
.../0004-BCM2835_DT-Fix-I2S-register-map.patch | 50 -
...-Prevent-spurious-interrupts-and-trap-the.patch | 30 -
.../0006-irqchip-bcm2835-Add-FIQ-support.patch | 127 -
...-irqchip-irq-bcm2835-Add-2836-FIQ-support.patch | 96 -
...erial-8250-Don-t-crash-when-nr_uarts-is-0.patch | 20 -
...2835-Set-base-to-0-give-expected-gpio-num.patch | 21 -
...2835-Fix-interrupt-handling-for-GPIOs-28-.patch | 146 -
...2835-Only-request-the-interrupts-listed-i.patch | 27 -
...cm2835-Support-pin-groups-other-than-7-11.patch | 80 -
...RM-bcm2835-Set-Serial-number-and-Revision.patch | 58 -
...-get-base-address-for-DMA-from-devicetree.patch | 65 -
...-add-24bit-support-update-bclk_ratio-to-m.patch | 79 -
...s-setup-clock-only-if-CPU-is-clock-master.patch | 54 -
...835-i2s-Eliminate-debugfs-directory-error.patch | 36 -
.../0018-bcm2835-i2s-Register-PCM-device.patch | 63 -
...i2s-Enable-MMAP-support-via-a-DT-property.patch | 44 -
...0-dmaengine-bcm2835-Add-slave-dma-support.patch | 320 -
...ine-bcm2835-set-residue_granularity-field.patch | 29 -
...cm2835-Load-driver-early-and-support-lega.patch | 97 -
...-dma-Fix-dreq-not-set-for-slave-transfers.patch | 21 -
...-Limit-cyclic-transfers-on-lite-channels-.patch | 36 -
.../0025-bcm2835-Add-support-for-uart1.patch | 57 -
...irmware-bcm2835-Add-missing-property-tags.patch | 62 -
.../0027-Main-bcm2708-bcm2709-linux-port.patch | 2418 -
...-squash-include-ARCH_BCM2708-ARCH_BCM2709.patch | 138 -
.../patches-4.4/0029-Add-dwc_otg-driver.patch | 60780 -------------------
.../0030-bcm2708-framebuffer-driver.patch | 3455 --
.../0031-dmaengine-Add-support-for-BCM2708.patch | 612 -
.../0032-MMC-added-alternative-MMC-driver.patch | 1691 -
...835-sdhost-driver-and-an-overlay-to-enabl.patch | 2021 -
...ma-Add-vc_cma-driver-to-enable-use-of-CMA.patch | 1326 -
.../0035-bcm2708-alsa-sound-driver.patch | 2678 -
.../patches-4.4/0036-bcm2708-vchiq-driver.patch | 13200 ----
.../0037-vc_mem-Add-vc_mem-driver.patch | 991 -
...deoCore-shared-memory-service-for-BCM2835.patch | 4393 --
...omem-device-for-rootless-user-GPIO-access.patch | 306 -
.../brcm2708/patches-4.4/0040-Add-SMI-driver.patch | 1930 -
.../patches-4.4/0041-Add-SMI-NAND-driver.patch | 358 -
...2-lirc-added-support-for-RaspberryPi-GPIO.patch | 841 -
.../patches-4.4/0043-Add-cpufreq-driver.patch | 257 -
...-thermal-driver-for-reporting-core-temper.patch | 193 -
.../0045-Add-Chris-Boot-s-i2c-driver.patch | 635 -
.../0046-char-broadcom-Add-vcio-module.patch | 221 -
...047-firmware-bcm2835-Support-ARCH_BCM270x.patch | 106 -
.../0048-bcm2835-add-v4l2-camera-device.patch | 7338 ---
...-mkknlimg-and-knlinfo-scripts-from-tools-.patch | 460 -
...port-for-the-CONFIG_CMDLINE_EXTEND-option.patch | 55 -
...0051-BCM2708-Add-core-Device-Tree-support.patch | 4564 --
...2-bcm2835-Match-with-BCM2708-Device-Trees.patch | 515 -
.../0053-fbdev-add-FBIOCOPYAREA-ioctl.patch | 91 -
...up-console-framebuffer-imageblit-function.patch | 209 -
...8-Allow-mac-address-to-be-set-in-smsc95xx.patch | 91 -
...e-realtime-clock-1-wire-chip-DS1307-and-1.patch | 242 -
...060-Added-Device-IDs-for-August-DVB-T-205.patch | 22 -
...le-CONFIG_MEMCG-but-leave-it-disabled-due.patch | 49 -
.../0062-ASoC-Add-support-for-PCM5102A-codec.patch | 128 -
.../0063-ASoC-Add-support-for-HifiBerry-DAC.patch | 165 -
.../0064-ASoC-Add-support-for-Rpi-DAC.patch | 275 -
...-Implement-MCLK-configuration-options-add.patch | 40 -
...d-support-for-HiFiBerry-Digi.-Driver-is-b.patch | 282 -
...-Set-idle_bias_off-to-false-Idle-bias-has.patch | 22 -
...audIO-Sound-Card-support-for-Raspberry-Pi.patch | 178 -
...ce-default-mouse-polling-interval-to-60Hz.patch | 36 -
.../0070-Added-support-for-HiFiBerry-DAC.patch | 190 -
...r-for-HiFiBerry-Amp-amplifier-add-on-boar.patch | 816 -
...ate-ds1307-driver-for-device-tree-support.patch | 27 -
...Add-pwr_led-and-the-required-input-trigge.patch | 169 -
...d-device-tree-compatible-string-and-an-ov.patch | 28 -
.../0075-Add-driver-for-rpi-proto.patch | 210 -
.../0076-config-Add-default-configs.patch | 2537 -
.../0077-bcm2835-bcm2835_defconfig.patch | 1426 -
...Add-touchscreen-driver-for-pi-LCD-display.patch | 290 -
...opy_to_user-and-__copy_from_user-performa.patch | 1509 -
...poweroff-Allow-it-to-work-on-Raspberry-Pi.patch | 35 -
...spidev-compatible-string-to-silence-warni.patch | 20 -
.../0082-scripts-dtc-Add-overlay-support.patch | 4389 --
...fd-Add-Raspberry-Pi-Sense-HAT-core-driver.patch | 838 -
.../patches-4.4/0084-RaspiDAC3-support.patch | 243 -
...85-tpa6130a2-Add-headphone-switch-control.patch | 91 -
.../0086-irq-bcm2835-Fix-building-with-2708.patch | 28 -
..._display-add-backlight-driver-and-overlay.patch | 250 -
...88-bcm2835-dma-Fix-up-convert-to-DMA-pool.patch | 85 -
...ti-platform-support-for-mkknlimg-and-knli.patch | 246 -
...-suport-for-3D-rendering-using-the-V3D-en.patch | 5557 --
.../0091-drm-vc4-Force-HDMI-to-connected.patch | 23 -
.../0092-drm-vc4-bo-cache-locking-fixes.patch | 147 -
.../0093-drm-vc4-bo-cache-locking-cleanup.patch | 92 -
...vc4-Use-job_lock-to-protect-seqno_cb_list.patch | 54 -
...c4-Drop-struct_mutex-around-CL-validation.patch | 63 -
...c4-Drop-struct_mutex-around-CL-validation.patch | 74 -
...dd-support-for-more-display-plane-formats.patch | 35 -
...m-vc4-No-need-to-stop-the-stopped-threads.patch | 26 -
...ove-extra-barrier-s-aroudn-CTnCA-CTnEA-se.patch | 32 -
...rm-vc4-Fix-a-typo-in-a-V3D-debug-register.patch | 33 -
...ble-VC4-modules-and-increase-CMA-size-wit.patch | 153 -
.../brcm2708/patches-4.4/0102-squash-fixups.patch | 43 -
...missing-vc4-kms-v3d-overlay.dtb-to-makefi.patch | 19 -
...-Also-build-the-driver-for-downstream-ker.patch | 21 -
...dts-Added-overlay-for-gpio_ir_recv-driver.patch | 104 -
...pio-module-and-add-a-device-tree-overlay-.patch | 100 -
.../0107-New-overlay-for-PiScreen2r.patch | 148 -
...verlay-for-Adafruit-PiTFT-2.8-capacitive-.patch | 145 -
...109-Add-support-for-the-HiFiBerry-DAC-Pro.patch | 539 -
.../0110-BCM270X_DT-Add-at86rf233-overlay.patch | 130 -
.../0111-mm-Remove-the-PFN-busy-warning.patch | 25 -
...optional-field-in-the-driver-struct-for-G.patch | 40 -
...-an-interface-for-capturing-the-GPU-state.patch | 333 -
...ate-a-bunch-of-code-to-match-upstream-sub.patch | 1893 -
...-driver-s-gem_object_free-function-from-C.patch | 59 -
...16-drm-vc4-Add-support-for-MSAA-rendering.patch | 518 -
...ew-more-non-functional-changes-to-sync-to.patch | 345 -
...-hpd-gpios-for-HDMI-GPIO-like-what-landed.patch | 22 -
...chronize-validation-code-for-v2-submissio.patch | 612 -
...use-mmc_debug-if-CONFIG_MMC_BCM2835-is-no.patch | 36 -
...k-timeout-fix-modprobe-baudrate-parameter.patch | 107 -
...-bcm270x_dt-Add-dwc2-and-dwc-otg-overlays.patch | 110 -
...Add-the-sdtweak-overlay-for-tuning-sdhost.patch | 73 -
...-Don-t-override-bus-width-capabilities-fr.patch | 24 -
...0125-SDIO-overlay-add-bus_width-parameter.patch | 42 -
...end-allowed-range-of-channels-and-sampler.patch | 36 -
...cm2835-restrict-channels-rate-to-8-960000.patch | 80 -
.../0128-rpi-update-vc_vchi_audioserv_defs.h.patch | 66 -
.../0129-bcm2835-implement-channel-map-API.patch | 421 -
...835-access-controls-under-the-audio-mutex.patch | 237 -
...ays-use-2-4-8-channels-for-multichannel-l.patch | 138 -
...y-allow-stereo-if-analogue-jack-is-select.patch | 61 -
.../0133-bcm2835-interpolate-audio-delay.patch | 90 -
...ost-Add-workaround-for-odd-behaviour-on-s.patch | 137 -
...35-bcm2835-sdhost-Add-debug_flags-dtparam.patch | 120 -
...Add-sdio_overclock-parameter-to-sdio-over.patch | 68 -
...add-support-for-the-DT-property-wakeup-so.patch | 93 -
.../0138-dt-overlay-add-wittypi-overlay.dts.patch | 57 -
...cm2708-Don-t-change-module-baudrate-param.patch | 98 -
...-24dB-digital-gain-to-be-applied-when-usi.patch | 99 -
...2x-Digital-gain-to-0dB-by-default-with-Hi.patch | 98 -
...M270X_DT-Adjust-overlay-README-formatting.patch | 729 -
.../0143-bcm2835-sdhost-Major-revision.patch | 2070 -
...270X_DT-Add-dtparams-for-the-SD-interface.patch | 235 -
...m-xfer-length-when-buffer-larger-than-all.patch | 37 -
...ost-Restore-ATOMIC-flag-to-PIO-sg-mapping.patch | 32 -
...c95xx-driver-to-check-for-a-valid-MAC-add.patch | 39 -
...dcw_otg-Make-trimming-messages-less-noisy.patch | 31 -
...BCM270X_DT-at86rf233-overlay-drop-to-3MHz.patch | 36 -
...m2835-sdhost-Downgrade-log-message-status.patch | 22 -
.../0151-config-Enable-HCI-over-UARTs.patch | 33 -
...52-hci_h5-Don-t-send-conf_req-when-ACTIVE.patch | 23 -
..._pl011-Don-t-use-DT-aliases-for-numbering.patch | 29 -
...-Add-bindings-for-the-auxiliary-periphera.patch | 72 -
...-Add-a-driver-for-the-auxiliary-periphera.patch | 118 -
.../0156-Aux-SPI-1-2-implementation.patch | 700 -
...d-missing-.owner-fields-in-sound-card-dri.patch | 107 -
...d-option-to-disable-the-crimes-against-tr.patch | 44 -
...0159-bcm2835-virtgpio-Virtual-GPIO-driver.patch | 244 -
.../0160-BCM270X_DT-Add-Pi3-support.patch | 323 -
...161-DT-Add-overlays-to-configure-I2C-pins.patch | 134 -
...era-fix-a-bug-in-computation-of-frame-tim.patch | 22 -
...163-BCM270X_DT-Add-pi3-disable-bt-overlay.patch | 96 -
...BCM270X_DT-Add-pi3-miniuart-bt-DT-overlay.patch | 117 -
...-Pi3-DT-Add-dtparams-for-the-SD-interface.patch | 25 -
.../0166-vchiq_arm-Tweak-the-logging-output.patch | 75 -
...bcm2835-sdhost-Only-claim-one-DMA-channel.patch | 160 -
...68-bcm2835-mmc-Only-claim-one-DMA-channel.patch | 170 -
.../0169-config-rebuild-with-savedefconfig.patch | 28 -
.../0170-config-Add-module-for-mcp3422-ADC.patch | 30 -
...-Pi3-DT-Add-pull-ups-on-the-UART-RX-lines.patch | 40 -
...X_DT-rpi-display-overlay-add-swapxy-param.patch | 38 -
.../0174-Remove-I2S-config-from-bt_pins.patch | 38 -
...75-Revert-scripts-dtc-Add-overlay-support.patch | 4390 --
...ipts-dtc-Update-to-upstream-version-1.4.1.patch | 2736 -
...0177-configfs-implement-binary-attributes.patch | 639 -
.../0178-OF-DT-Overlay-configfs-interface.patch | 408 -
...elease_resource-against-resources-without.patch | 27 -
...0X_DT-Add-a-.dtbo-target-use-for-overlays.patch | 193 -
.../0181-scripts-knlinfo-Decode-DDTK-atom.patch | 31 -
...mic-Device-Tree-for-bcmrpi_defconfig-and-.patch | 40 -
...dd-CONFIG_OF_CONFIGFS-to-bcmrpi_defconfig.patch | 29 -
...ild-dtbs_install-installs-.dtbo-files-too.patch | 42 -
...cm2835-sdhost-Workaround-for-slow-sectors.patch | 118 -
...186-BCM270X_DT-Add-labels-to-spidev-nodes.patch | 114 -
...-BCM270X_DT-Use-spidev-labels-in-overlays.patch | 628 -
...DT-Build-and-document-the-wittypi-overlay.patch | 50 -
...-Fix-UMR-causing-corrupt-dtbo-overlay-fil.patch | 26 -
.../0190-BCM270X_DT-Add-dtparam-for-uart1.patch | 77 -
...-overlay-Use-label-so-overrides-can-apply.patch | 34 -
...-a-debugfs-node-for-tracking-execution-st.patch | 55 -
...lude-vc4_drm.h-in-uapi-in-downstream-buil.patch | 20 -
...-Validate-that-WAIT_BO-padding-is-cleared.patch | 25 -
...-the-clear-color-for-the-first-tile-rende.patch | 48 -
...urn-an-ERR_PTR-from-BO-creation-instead-o.patch | 136 -
...ix-ERESTARTSYS-error-return-from-BO-waits.patch | 32 -
...Drop-error-message-on-seqno-wait-timeouts.patch | 27 -
...270X_DT-Add-1-bit-SDIO-using-minimal-pins.patch | 81 -
...rlay-and-enable-support-for-QCA7000-board.patch | 127 -
...l-Take-care-starting-a-hung-up-tty-s-port.patch | 28 -
...iuart-bt-overlay-Correct-and-clarify-info.patch | 41 -
...rlays-Params-must-have-in-overlay-targets.patch | 52 -
...5-BCM270X_DT-Switch-Compute-Module-to-MMC.patch | 53 -
...-t-free-qh-align-buffers-in-atomic-contex.patch | 43 -
...ble-the-hack-for-Split-Interrupt-transact.patch | 28 -
..._DT-Remove-explicit-claiming-of-UART-pins.patch | 89 -
...irc_rpi-Lower-IR-reception-error-to-debug.patch | 21 -
...rm-Access-the-dequeue_pending-flag-locked.patch | 58 -
.../0211-BCM270X_DT-Add-pi3-act-led-overlay.patch | 94 -
...vchiq_arm-Service-callbacks-must-not-fail.patch | 26 -
...d-configs-and-overlay-for-PCA9548-I2C-mux.patch | 133 -
...-BCM270X_DT-Add-DS1339-to-i2c-rtc-overlay.patch | 58 -
...from_user-CPU_SW_DOMAIN_PAN-compatibility.patch | 53 -
...m2835-sdhost-Adjust-to-core-clock-changes.patch | 339 -
...70X_DT-Document-hazards-of-sdhost-overlay.patch | 34 -
...8-cpufreq-Temporarily-ignore-io_is_busy-1.patch | 31 -
...t-cpufreq-Temporarily-ignore-io_is_busy-1.patch | 26 -
...20-net-sched-add-skb_at_tc_ingress-helper.patch | 31 -
...35-sdhost-Precalc-divisors-and-overclocks.patch | 270 -
...835-sdhost-Precalc-divisors-and-overclock.patch | 266 -
...m2835-sdhost-Adjust-to-core-clock-changes.patch | 327 -
...sdhost-Firmware-manages-the-clock-divisor.patch | 226 -
...rt-cpufreq-Temporarily-ignore-io_is_busy-.patch | 26 -
.../0227-config-Enabled-IPV6_SUBTREES.patch | 30 -
...0228-add-smsc95xx-packetsize-module_param.patch | 42 -
...power-off-rather-than-busy-spinning-when-.patch | 25 -
...835-dma-Fix-dreq-not-set-for-slave-transf.patch | 31 -
...Add-CONFIG_PWM_PCA9685-for-NXP-PCA9685-dr.patch | 92 -
...70X_DT-Don-t-generate-linux-phandle-props.patch | 36 -
.../0233-V4L2-driver-updates-1393.patch | 718 -
...35-sdhost-Reset-the-clock-in-task-context.patch | 107 -
...le-CONFIG_IPV6_ROUTER_PREF-for-networks-w.patch | 31 -
.../0236-Enable-hid-betopff-module.patch | 32 -
...-IPV6-a-module-and-regenerate-with-defcon.patch | 69 -
.../0238-BCM270X_DT-Add-dpi24-overlay.patch | 74 -
...dIO-DAC-ASoC-driver-to-set-card-dai-confi.patch | 57 -
...-for-the-Digital-Dreamtime-Akkordion-musi.patch | 104 -
...41-Add-Support-for-BoomBerry-Audio-boards.patch | 605 -
...42-Add-support-for-mcp7940x-family-of-RTC.patch | 43 -
...config-Fix-typo-on-BoomBerry-configuratio.patch | 22 -
...-boomberry-dac-Adjust-for-ALSA-API-change.patch | 26 -
...-unused-sm_cache_map_vector-definition-14.patch | 34 -
...s-mkknlimg-Append-a-trailer-for-all-input.patch | 63 -
...hermal-Don-t-report-unsupported-trip-type.patch | 69 -
...s-dtc-Only-emit-local-fixups-for-overlays.patch | 21 -
...not-require-substream-for-accessing-chmap.patch | 50 -
...-fallback-channel-layouts-if-channel-map-.patch | 41 -
...0251-bcm2835-log-which-channel-map-is-set.patch | 32 -
...-add-a-round-up-ability-to-the-clock-divi.patch | 69 -
...cm2835-Support-for-clock-parent-selection.patch | 188 -
.../0254-clk-bcm2835-Add-PWM-clock-support.patch | 55 -
...-added-missing-clock-register-definitions.patch | 48 -
...-correctly-enable-fractional-clock-suppor.patch | 133 -
...-clk-bcm2835-clean-up-coding-style-issues.patch | 52 -
...35-expose-raw-clock-registers-via-debugfs.patch | 188 -
...-remove-use-of-BCM2835_CLOCK_COUNT-in-dri.patch | 236 -
...-reorganize-bcm2835_clock_array-assignmen.patch | 925 -
...lk-bcm2835-enable-management-of-PCM-clock.patch | 40 -
...lk-bcm2835-add-missing-PLL-clock-dividers.patch | 73 -
...lk-bcm2835-add-missing-osc-and-per-clocks.patch | 184 -
...-Define-two-new-packets-from-the-latest-f.patch | 33 -
...5-ARM-bcm2835-add-rpi-power-domain-driver.patch | 361 -
...5-clarify-RASPBERRYPI_FIRMWARE-dependency.patch | 36 -
...m2708-Enable-building-power-domain-driver.patch | 20 -
...8-Add-RASPBERRYPI_POWER-to-the-defconfigs.patch | 50 -
...-the-power-domain-driver-to-the-device-tr.patch | 25 -
...erence-the-HDMI-power-domain-for-the-HDMI.patch | 28 -
...y_to_user-returns-the-number-of-bytes-rem.patch | 86 -
...ocate-enough-memory-in-vc4_save_hang_stat.patch | 26 -
...73-drm-vc4-fix-warning-in-validate-printf.patch | 32 -
...prove-comments-on-vc4_plane_state-members.patch | 36 -
...dd-missing-__iomem-annotation-to-hw_dlist.patch | 25 -
...e-the-plane-clipping-scaling-setup-to-a-s.patch | 143 -
...-a-proper-short-circut-path-for-legacy-cu.patch | 192 -
...e-the-CRTCs-cooperate-on-allocating-displ.patch | 248 -
...-vc4-Add-more-display-planes-to-each-CRTC.patch | 106 -
...-which-value-is-being-used-for-source-ima.patch | 76 -
...Add-support-for-scaling-of-display-planes.patch | 579 -
.../0282-drm-vc4-Add-support-for-YUV-planes.patch | 519 -
...4-Fix-spurious-GPU-resets-due-to-BO-reuse.patch | 81 -
...-a-framebuffer-reference-leak-on-async-fl.patch | 26 -
...Bring-HDMI-up-from-power-off-if-necessary.patch | 72 -
...vc4-Add-another-reg-to-HDMI-debug-dumping.patch | 24 -
...-Fix-the-name-of-the-VSYNCD_EVEN-register.patch | 36 -
...x-setting-of-vertical-timings-in-the-CRTC.patch | 34 -
...c4-Initialize-scaler-DISPBKGND-on-modeset.patch | 68 -
...rove-throughput-by-pipelining-binning-and.patch | 429 -
...-gpiolib-know-that-we-re-OK-with-sleeping.patch | 27 -
...pect-GPIO_ACTIVE_LOW-on-HDMI-HPD-if-set-i.patch | 57 -
...4-Return-EFAULT-on-copy_from_user-failure.patch | 36 -
...ognize-a-more-specific-compatible-string-.patch | 28 -
...08-Move-the-CMA-range-down-for-kernel-4.4.patch | 24 -
...-fix-check-of-error-code-returned-by-devm.patch | 33 -
...rm-Add-completion-records-under-the-mutex.patch | 63 -
.../0298-config-Add-DRM_UDL-module.patch | 59 -
...-bcm2835-i2s-Reduce-the-TX-DREQ-threshold.patch | 48 -
...-V4L2-Request-maximum-resolution-from-GPU.patch | 193 -
...0301-ARM-bcm2835-add-i2s-gpio28-31-for-cm.patch | 62 -
...c4-Add-DT-parameters-to-control-CMA-usage.patch | 75 -
...SH-BCM270X_DT-Add-make-rule-for-sdio-1bit.patch | 22 -
.../0304-dts-add-overlay-for-pitft22.patch | 123 -
...0X_DT-Sound-DT-adjustments-for-Dynamic-DT.patch | 578 -
...DT-Fix-codec-use-in-hifiberry-dac-overlay.patch | 21 -
...vert-bcm2835-log-which-channel-map-is-set.patch | 33 -
...835-add-fallback-channel-layouts-if-chann.patch | 31 -
...835-do-not-require-substream-for-accessin.patch | 51 -
...12-Revert-bcm2835-interpolate-audio-delay.patch | 70 -
...835-only-allow-stereo-if-analogue-jack-is.patch | 49 -
...835-always-use-2-4-8-channels-for-multich.patch | 135 -
...-Revert-bcm2835-implement-channel-map-API.patch | 496 -
...835-extend-allowed-range-of-channels-and-.patch | 37 -
...-bcm2835-Return-pins-to-inputs-when-freed.patch | 40 -
...-BCM270X_DT-i2c0-bcm2708-pin-group-params.patch | 99 -
...-config-Add-CONFIG_DRM_LOAD_EDID_FIRMWARE.patch | 30 -
...evert-rpi-update-vc_vchi_audioserv_defs.h.patch | 63 -
...-config-Add-CONFIG_DRM_LOAD_EDID_FIRMWARE.patch | 31 -
...7-adc-Add-basic-machine-driver-for-adau19.patch | 285 -
...-24dB-digital-gain-to-be-applied-when-usi.patch | 60 -
...-config-Add-CONFIG_DRM_LOAD_EDID_FIRMWARE.patch | 30 -
...Move-vc4-node-contents-to-bcm2708_common..patch | 324 -
...Set-correct-HDMI-HPD-GPIO-levels-for-vari.patch | 69 -
...27-Revert-drm-vc4-Force-HDMI-to-connected.patch | 26 -
...nclude-DRM_PANEL_SIMPLE-in-the-defconfigs.patch | 33 -
...n-encoder-and-connector-type-enum-for-DPI.patch | 64 -
...0330-dt-bindings-Add-binding-docs-for-V3D.patch | 42 -
.../patches-4.4/0331-drm-vc4-Add-DPI-driver.patch | 673 -
...c4-Fix-NULL-deref-in-HDMI-init-error-path.patch | 25 -
...k-out-the-simplefb-framebuffer-before-we-.patch | 53 -
.../0334-drm-vc4-Rename-async-to-nonblock.patch | 45 -
.../0335-drm-vc4-Add-support-for-gamma-ramps.patch | 137 -
...6-drm-vc4-Add-missing-render-node-support.patch | 26 -
...-simple-Add-the-7-DPI-panel-from-Adafruit.patch | 86 -
...Add-the-disabled-by-default-DPI-device-no.patch | 33 -
...-get_vblank_counter-with-proper-no-op-for.patch | 31 -
...-drm_vblank_put-get-imbalance-in-page-fli.patch | 47 -
...X_DT-Add-umbrella-I2C-Mux-overlay-i2c-mux.patch | 269 -
...X_DT-Include-address-override-for-pca9542.patch | 24 -
..._DT-Fix-the-tinylcd35-overlay-RTC-support.patch | 68 -
...clk-Allow-clocks-to-be-marked-as-CRITICAL.patch | 43 -
...lk-bcm2835-Mark-the-VPU-clock-as-critical.patch | 46 -
...-Mark-GPIO-clocks-enabled-at-boot-as-crit.patch | 54 -
...-Skip-PLLC-clocks-when-deciding-on-a-new-.patch | 71 -
...Add-MMC_QUIRK_ERASE_BROKEN-for-some-cards.patch | 56 -
...jector.net-Pi-soundcard-with-low-jitter-a.patch | 284 -
...ly-QUIRK_BROKEN_ERASE-to-other-capacities.patch | 23 -
...d-card_quirks-module-parameter-log-quirks.patch | 76 -
...ensure-that-any-pending-alarm-is-cleared-.patch | 58 -
...rt-Revert-drm-vc4-Force-HDMI-to-connected.patch | 27 -
.../0354-config-Add-NF_MATCH_RPFILTER.patch | 46 -
...ay-for-Microchip-MCP23017-I2C-gpio-expand.patch | 86 -
...era-Fix-max-min-error-when-looping-over-c.patch | 24 -
...Berry-name-to-JustBoom-in-all-locations-d.patch | 1139 -
...m-to-force-HiFiBerry-DAC-Pro-into-slave-m.patch | 82 -
...368-simple-add-sound-dai-cells-to-I2S-def.patch | 33 -
...V4L2-Increase-minimum-resolution-to-32x32.patch | 31 -
...config-Add-support-for-Logitech-Rumblepad.patch | 36 -
...for-RRA-DigiDAC1-soundcard-using-WM8741-W.patch | 602 -
...-V4L2-Correct-handling-for-BGR24-vs-RGB24.patch | 170 -
...X_DT-Add-mcp23017-to-the-overlay-Makefile.patch | 20 -
...X_DT-Sort-entries-to-placate-check-script.patch | 56 -
...rlay-gpio_pin-shouldn-t-change-pull-setti.patch | 22 -
...core-define-a-default-timeout-for-drivers.patch | 25 -
...media-rc-gpio-ir-recv-add-timeout-on-idle.patch | 91 -
...ove-a-now-duplicated-definition-IR_DEFAUL.patch | 24 -
...-wakeup-source-option-for-the-i2c-rtc-Dev.patch | 36 -
.../0381-BCM270X_DT-Fix-rpi-dac-overlay.patch | 34 -
...DT-Make-i2c-gpio-usable-by-other-overlays.patch | 37 -
.../patches-4.4/0386-Add-ads1015-overlay.patch | 155 -
...-Fixed-MCP23017-section-in-overlay-README.patch | 22 -
...rt-bcm2835-dma-Fix-up-convert-to-DMA-pool.patch | 86 -
...835-dma-Limit-cyclic-transfers-on-lite-ch.patch | 35 -
...ngine-bcm2835-Load-driver-early-and-suppo.patch | 90 -
...t-dmaengine-bcm2835-Add-slave-dma-support.patch | 312 -
...cm2835-remove-unnecessary-masking-of-dma-.patch | 56 -
...cm2835-add-additional-defines-for-DMA-reg.patch | 93 -
...cm2835-move-cyclic-member-from-bcm2835_ch.patch | 53 -
...cm2835-move-controlblock-chain-generation.patch | 378 -
...cm2835-limit-max-length-based-on-channel-.patch | 114 -
...cm2835-add-slave_sg-support-to-bcm2835-dm.patch | 182 -
...cm2835-add-dma_memcopy-support-to-bcm2835.patch | 87 -
...ngine-bcm2835-use-platform_get_irq_byname.patch | 170 -
...cm2835-Load-driver-early-and-support-lega.patch | 89 -
...-changed-bcrm-dma-channel-mask-to-mask-ou.patch | 26 -
...-add-interrupt-names-and-apply-correct-ma.patch | 50 -
...-make-dma-channel-0-available-for-kms-set.patch | 28 -
...e-bcm2835-Fix-cyclic-DMA-period-splitting.patch | 38 -
...cm2835-Avoid-splitting-periods-into-very-.patch | 56 -
...cm2835-Fix-polling-for-completion-of-DMA-.patch | 68 -
...-BCM270X_DT-Add-spi-rtc-overlay-on-SPI0.0.patch | 76 -
...0409-rtc-Add-SPI-alias-for-pcf2123-driver.patch | 20 -
...rt-for-headphones-microphone-and-bclk_rat.patch | 119 -
...411-IQaudIO-auto-mute-for-AMP-and-DigiAMP.patch | 272 -
...2-mmc-Apply-ERASE_BROKEN-quirks-correctly.patch | 28 -
...support-for-xpad-driver-fixes-flashing-le.patch | 31 -
...l-information-for-getting-pi3-miniuart-bt.patch | 25 -
...835-sdhost-Improvements-to-error-recovery.patch | 312 -
...m2835-Fix-return-type-of-bcm2835_pmx_free.patch | 27 -
...417-Add-IQAudIO-Digi-WM8804-board-support.patch | 399 -
...rlay-for-NXP-SC16IS752-Dual-UART-with-SPI.patch | 106 -
...19-spi-bcm2835-Disable-forced-software-CS.patch | 46 -
...70X_DT-Overlay-to-re-enable-HW-CS-on-SPI0.patch | 69 -
...d-support-for-Dion-Audio-LOCO-DAC-AMP-HAT.patch | 261 -
.../0422-ASoc-wm8731-add-32bit-mode.patch | 39 -
..._DT-Declare-the-audio-PWM-pins-explicitly.patch | 122 -
...424-BCM270X_DT-Restore-lost-closing-brace.patch | 20 -
...Add-driver-for-mcp23017-I2C-GPIO-expander.patch | 56 -
..._arm-Avoid-use-of-mutex-in-add_completion.patch | 192 -
...-bcm2708_fb-Default-framebuffer-to-32-bit.patch | 21 -
.../0428-fix-auto-sense-in-lirc_rpi-driver.patch | 45 -
.../0429-enable-gembird-joypad-support.patch | 30 -
.../0430-Added-HiFiBerry-Digi-Pro-driver.patch | 187 -
...-Mark-the-CM-SDRAM-clock-s-parent-as-crit.patch | 73 -
...-Don-t-rate-change-PLLs-on-behalf-of-divi.patch | 27 -
...-Do-appropriate-name-lookups-for-DSI1-s-p.patch | 125 -
...2835-Add-an-enum-for-the-DSI1-pixel-clock.patch | 87 -
...helper-Remove-implicit-call-to-disable_un.patch | 79 -
...d-assert_falling_edge-to-pps-gpio-overlay.patch | 31 -
.../0437-drm-mipi-dsi-Unregister-bus-at-exit.patch | 30 -
...i-Allow-to-build-drm-mipi-dsi-as-a-module.patch | 32 -
...m-vc4-Fix-flipped-HVS-channels-for-DSI0-1.patch | 30 -
...-support-for-feeding-DSI-encoders-from-th.patch | 96 -
...rt-switching-to-using-debugfs_reg32-helpe.patch | 156 -
.../patches-4.4/0442-drm-vc4-Add-DSI1-driver.patch | 1914 -
...dd-support-for-the-Raspberry-Pi-7-Touchsc.patch | 390 -
...CM270X-Add-the-DSI-panel-to-the-defconfig.patch | 31 -
...-the-DSI-and-DSI-panel-nodes-to-the-VC4-o.patch | 84 -
...f_device_uevent_modalias-for-DRM_MIPI_DSI.patch | 21 -
...dalias-uevents-for-the-DSI-devices-we-cre.patch | 48 -
..._hdmi-add-missing-of_node_put-after-calli.patch | 46 -
.../0449-drm-vc4-Use-for_each_plane_in_state.patch | 42 -
...c4-Fix-ioctl-permissions-for-render-nodes.patch | 39 -
...e-pageflip-completion-handling-more-robus.patch | 126 -
...an-up-error-exit-path-on-failed-dpi_conne.patch | 53 -
...nable-XBGR8888-and-ABGR8888-pixel-formats.patch | 34 -
...d-the-HVS-before-we-bind-the-individual-C.patch | 28 -
...vc4-Implement-precise-vblank-timestamping.patch | 358 -
...drm-vc4-remove-redundant-ret-status-check.patch | 35 -
...c4-add-extern-C-guard-for-the-UAPI-header.patch | 34 -
...-vc4-Fix-definition-of-QPU_R_MS_REV_FLAGS.patch | 25 -
...9-drm-vc4-Fix-a-the-the-typo-in-a-comment.patch | 22 -
...urn-EBUSY-if-there-s-already-a-pending-fl.patch | 44 -
.../0461-config-Enable-SENSORS_LM75.patch | 30 -
.../0462-config-Enable-SERIAL_SC16IS7XX.patch | 30 -
...-Don-t-allow-responses-from-VC-to-be-inte.patch | 63 -
...4-BCM270X-Connect-V3D-to-its-power-domain.patch | 23 -
.../0465-drm-vc4-Enable-runtime-PM.patch | 205 -
...p-firmware-node-getting-now-that-we-use-t.patch | 54 -
...-runtime-PM-to-power-cycle-the-device-whe.patch | 102 -
...rop-debug-printf-from-the-Raspberry-Pi-to.patch | 21 -
...lace-HDMI-force-connected-with-an-EDID-pr.patch | 42 -
...ethernet-enc28j60-add-device-tree-support.patch | 143 -
...j60-Fix-race-condition-in-enc28j60-driver.patch | 64 -
.../patches-4.4/0472-Add-cm3-dts-file.patch | 200 -
...70X-Drop-HPD-setting-from-the-common-dtsi.patch | 21 -
...-Drop-incorrect-HDMI-HPD-line-from-the-DT.patch | 26 -
...-a-getparam-ioctl-for-getting-the-V3D-ide.patch | 124 -
...e-validation-s-current-max-ip-into-the-va.patch | 176 -
...-a-bitmap-of-branch-targets-during-shader.patch | 200 -
...-support-for-branching-in-shader-validati.patch | 475 -
...-a-getparam-to-signal-support-for-branche.patch | 38 -
...-t-force-new-binner-overflow-allocation-p.patch | 28 -
...-drm_free_large-on-handles-to-match-its-a.patch | 27 -
...Fix-oops-when-userspace-hands-in-a-bad-BO.patch | 26 -
...-overflow-mem-unreferencing-when-the-binn.patch | 57 -
.../0484-config-Enable-SERIAL_SC16IS7XX_SPI.patch | 33 -
...-Microchip-MCP23S08-17-SPI-gpio-expanders.patch | 791 -
.../0486-BCM270X_DT-Add-audio_pins-to-CM-dtb.patch | 24 -
...-BCM270X_DT-Don-t-enable-UART0-in-CM3-dtb.patch | 37 -
.../0488-overlays-Add-audremap-overlay.patch | 56 -
...s-Add-swap_lr-and-enable_jack-to-audremap.patch | 50 -
...Clarify-gpio-poweroff-semantics-in-README.patch | 24 -
...erlays-added-sc16is750-UART-over-I2C-1617.patch | 81 -
...ix-l2cap_sock_setsockopt-with-optname-BT_.patch | 33 -
.../0493-config-Add-CONFIG_IPVLAN-module.patch | 30 -
.../0494-config-Add-CONFIG_VXLAN-module.patch | 30 -
...c_bcm2708-Write-to-FIFO-correctly-v2-1574.patch | 48 -
...-sdhost-Don-t-exit-cmd-wait-loop-on-error.patch | 63 -
...X_DT-Use-bcm2835-sdhost-on-Compute-Module.patch | 30 -
...e-that-parameters-are-properly-checked-wi.patch | 27 -
...0499-config-Enabled-SENSORS_INA2XX-module.patch | 30 -
.../0500-overlays-Add-dpi18-overlay-1634.patch | 75 -
...ow-some-more-signals-to-be-packed-with-un.patch | 38 -
...-firmware-Export-the-general-transaction-.patch | 42 -
...-firmware-Define-the-MBOX-channel-in-the-.patch | 21 -
...-a-mode-for-using-the-closed-firmware-for.patch | 776 -
...-an-overlay-for-enabling-the-vc4-driver-i.patch | 189 -
...DAC-boards-Initial-2-channel-stereo-suppo.patch | 324 -
...t-typos-in-spi-gpio35-39-overlay.dts-1651.patch | 29 -
...ble-limited-range-RGB-output-with-CEA-mod.patch | 83 -
...Adafruit-pitft35-touchscreen-support-1657.patch | 196 -
...-races-when-the-CS-reads-from-render-targ.patch | 220 -
...ix-up-the-limited-range-RGB-output-commit.patch | 29 -
...rease-timeout-for-HDMI_SCHEDULER_CONTROL-.patch | 34 -
...-drm-vc4-Disallow-interlaced-modes-on-DPI.patch | 37 -
...c4-Fix-handling-of-interlaced-video-modes.patch | 104 -
.../0517-drm-vc4-Reject-doublescan-modes.patch | 30 -
...ble-precise-vblank-timestamping-for-inter.patch | 61 -
...ble-Disable-vblanks-properly-in-crtc-en-d.patch | 38 -
...-Fix-support-for-interlaced-modes-on-HDMI.patch | 211 -
...-Clamp-the-PLL-s-requested-rate-to-the-ha.patch | 43 -
...drm-vc4-Set-up-the-AVI-and-SPD-infoframes.patch | 223 -
...-vc4-Add-support-for-double-clocked-modes.patch | 127 -
...70X_DT-Update-CM3-to-use-sdhost-interface.patch | 36 -
...drm-vc4-Fix-memory-leak-of-the-CRTC-state.patch | 26 -
...x-kdump-cleanup-aborted-E820_PRAM-max_pfn.patch | 60 -
...527-Support-for-Blokas-Labs-pisound-board.patch | 1208 -
...528-pisound-Fix-a-warning-in-DEBUG-builds.patch | 31 -
.../0529-config-Add-CONFIG_HTU21-module.patch | 30 -
.../0530-spi-bcm2835-Remove-unused-code.patch | 93 -
...Add-ioctl-for-reading-gpu-memory-through-.patch | 167 -
...Create-coherent-buffer-and-push-to-firmwa.patch | 244 -
...io-Create-coherent-buffer-and-push-to-fir.patch | 169 -
...io-Pass-device-structure-into-dma_zalloc_.patch | 53 -
...Pass-device-structure-into-dma_zalloc_coh.patch | 38 -
...-a-couple-error-codes-in-vc4_cl_lookup_bo.patch | 39 -
...-termination-of-the-initial-scan-for-bran.patch | 68 -
...-support-for-rendering-with-ETC1-textures.patch | 55 -
...-runtime-autosuspend-to-avoid-thrashing-V.patch | 78 -
...4-Use-drm_gem_object_unreference_unlocked.patch | 76 -
...-drm_malloc_ab-to-fix-large-rendering-job.patch | 57 -
...ree-hang-state-before-destroying-BO-cache.patch | 29 -
...e-basic-types-for-dma-addresses-as-these-.patch | 23 -
...orrect-bus-address-for-dest-of-dma-memcpy.patch | 29 -
...vc4-Add-fragment-shader-threading-support.patch | 228 -
...-Use-struct-device-for-dma_alloc_coherent.patch | 29 -
...dts-Visit-overlays-subdir-unconditionally.patch | 34 -
...or-Fix-bit-offsets-for-equal-volume-and-a.patch | 55 -
...-config-Add-ABX80X-RTC-driver-and-overlay.patch | 96 -
...0550-config-Add-AK4554-audio-codec-driver.patch | 33 -
.../patches-4.4/0551-kbuild-add-fno-PIE.patch | 40 -
...d-Steal-gcc-s-pie-from-the-very-beginning.patch | 49 -
...RM-dts-Restore-dtbs_install-functionality.patch | 25 -
...4-BCM270X_DT-Update-UART0-clock-frequency.patch | 29 -
...M2835-v4l2-Fix-a-conformance-test-failure.patch | 25 -
...M270X_DT-Add-overlay-for-enc28j60-on-SPI2.patch | 97 -
...i-Delete-vestigial-gpio_in_pull-parameter.patch | 38 -
.../0558-BCM270X_DT-Add-i2c-sensor-overlay.patch | 92 -
...-overlays-overlay.dtb-overlays-.dtbo-1752.patch | 21 -
...dragonrise-fix-HID-Descriptor-for-0x0006-.patch | 99 -
...rng-Avoid-initialising-if-already-enabled.patch | 26 -
.../0562-Pisound-dynamic-overlay-1760.patch | 144 -
...-for-Silicon-Labs-Si7013-20-21-humidity-t.patch | 90 -
.../0564-pisound-improvements-1778.patch | 294 -
..._name-properties-to-JustBoom-drivers-1787.patch | 32 -
...-Changes-for-allowing-asymmetric-sample-f.patch | 96 -
...7-BCM270X_DT-Add-pi3-disable-wifi-overlay.patch | 56 -
...move-ppos-increment-in-configfs_write_bin.patch | 49 -
.../0569-config-Add-CONFIG_DM_CACHE.patch | 31 -
.../0570-BCM270X_DT-Add-spi0-cs-overlay.patch | 81 -
...835-i2s-Changes-for-allowing-asymmetric-s.patch | 96 -
.../0572-BCM270X_DT-Enable-UART0-on-CM3.patch | 23 -
...dd-CONFIG_MD_M25P80-and-CONFIG_MD_SPI_NOR.patch | 37 -
...-USB-config-options-for-bcm2709_defconfig.patch | 48 -
..._DT-Add-reference-to-audio_pins-to-CM-dtb.patch | 28 -
.../0576-Add-overlay-for-mcp3008-adc-1818.patch | 281 -
.../0577-config-add-slcan-kernel-module.patch | 31 -
...-sending-of-page-flip-completion-events-i.patch | 42 -
...clk-bcm2835-Fix-fixed_divider-of-pllh_aux.patch | 27 -
...port-rate-change-propagation-on-bcm2835-c.patch | 124 -
...ow-rate-change-propagation-to-PLLH_AUX-on.patch | 35 -
...-maybe-uninitialized-warning-in-bcm2835_c.patch | 29 -
...-Don-t-rate-change-PLLs-on-behalf-of-DSI-.patch | 172 -
...m-Remove-unnecessary-dev_info-output-1830.patch | 22 -
.../patches-4.4/1000-mfd-rpisense-disable.patch | 10 -
564 files changed, 198905 deletions(-)
diff --git a/target/linux/brcm2708/bcm2708/config-4.4 b/target/linux/brcm2708/bcm2708/config-4.4
deleted file mode 100644
index e74ad8e..0000000
--- a/target/linux/brcm2708/bcm2708/config-4.4
+++ /dev/null
@@ -1,364 +0,0 @@
-# CONFIG_AIO is not set
-CONFIG_ALIGNMENT_TRAP=y
-# CONFIG_AMBA_PL08X is not set
-# CONFIG_APM_EMULATION is not set
-CONFIG_ARCH_BCM2708=y
-# CONFIG_ARCH_BCM2709 is not set
-CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
-CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
-CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y
-# CONFIG_ARCH_HAS_SG_CHAIN is not set
-CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
-CONFIG_ARCH_HIBERNATION_POSSIBLE=y
-CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
-CONFIG_ARCH_NR_GPIO=0
-CONFIG_ARCH_REQUIRE_GPIOLIB=y
-# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
-# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
-CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
-CONFIG_ARCH_SUPPORTS_UPROBES=y
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_ARCH_USE_BUILTIN_BSWAP=y
-CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y
-CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
-CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
-CONFIG_ARM=y
-CONFIG_ARM_AMBA=y
-CONFIG_ARM_CPU_SUSPEND=y
-CONFIG_ARM_ERRATA_411920=y
-CONFIG_ARM_L1_CACHE_SHIFT=5
-# CONFIG_ARM_SP805_WATCHDOG is not set
-CONFIG_ARM_THUMB=y
-CONFIG_ARM_UNWIND=y
-# CONFIG_BACKLIGHT_CLASS_DEVICE is not set
-CONFIG_BACKLIGHT_LCD_SUPPORT=y
-# CONFIG_BCM2708_NOL2CACHE is not set
-CONFIG_BCM2708_VCHIQ=y
-CONFIG_BCM2708_VCMEM=y
-# CONFIG_BCM2835_DEVGPIOMEM is not set
-CONFIG_BCM2835_MBOX=y
-# CONFIG_BCM2835_SMI is not set
-CONFIG_BCM2835_WDT=y
-CONFIG_BCM_VCIO=y
-CONFIG_BCM_VC_CMA=y
-CONFIG_BCM_VC_SM=y
-# CONFIG_BLK_DEV_INITRD is not set
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_COUNT=16
-CONFIG_BLK_DEV_RAM_SIZE=4096
-CONFIG_BLK_DEV_SD=y
-CONFIG_BRCM_CHAR_DRIVERS=y
-CONFIG_BUILD_BIN2C=y
-# CONFIG_CACHE_L2X0 is not set
-CONFIG_CLKDEV_LOOKUP=y
-CONFIG_CLKSRC_MMIO=y
-CONFIG_CLKSRC_OF=y
-CONFIG_CLKSRC_PROBE=y
-CONFIG_CLONE_BACKWARDS=y
-CONFIG_CMA=y
-CONFIG_CMA_ALIGNMENT=8
-CONFIG_CMA_AREAS=7
-# CONFIG_CMA_DEBUG is not set
-# CONFIG_CMA_DEBUGFS is not set
-CONFIG_CMA_SIZE_MBYTES=16
-# CONFIG_CMA_SIZE_SEL_MAX is not set
-CONFIG_CMA_SIZE_SEL_MBYTES=y
-# CONFIG_CMA_SIZE_SEL_MIN is not set
-# CONFIG_CMA_SIZE_SEL_PERCENTAGE is not set
-CONFIG_COMMON_CLK=y
-CONFIG_CONFIGFS_FS=y
-CONFIG_CONSOLE_TRANSLATIONS=y
-CONFIG_CPU_32v6=y
-CONFIG_CPU_ABRT_EV6=y
-# CONFIG_CPU_BPREDICT_DISABLE is not set
-CONFIG_CPU_CACHE_V6=y
-CONFIG_CPU_CACHE_VIPT=y
-CONFIG_CPU_COPY_V6=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-CONFIG_CPU_HAS_ASID=y
-# CONFIG_CPU_ICACHE_DISABLE is not set
-CONFIG_CPU_IDLE=y
-CONFIG_CPU_IDLE_GOV_LADDER=y
-CONFIG_CPU_IDLE_GOV_MENU=y
-CONFIG_CPU_PABRT_V6=y
-CONFIG_CPU_PM=y
-CONFIG_CPU_TLB_V6=y
-CONFIG_CPU_V6=y
-CONFIG_CRC16=y
-CONFIG_CRYPTO_CRC32C=y
-CONFIG_CRYPTO_HASH=y
-CONFIG_CRYPTO_HASH2=y
-CONFIG_CRYPTO_RNG2=y
-CONFIG_CRYPTO_WORKQUEUE=y
-CONFIG_DCACHE_WORD_ACCESS=y
-CONFIG_DEBUG_BUGVERBOSE=y
-CONFIG_DEBUG_INFO=y
-CONFIG_DEBUG_LL_INCLUDE="mach/debug-macro.S"
-# CONFIG_DEBUG_UART_8250 is not set
-# CONFIG_DEBUG_USER is not set
-CONFIG_DEFAULT_CFQ=y
-# CONFIG_DEFAULT_DEADLINE is not set
-CONFIG_DEFAULT_IOSCHED="cfq"
-CONFIG_DMADEVICES=y
-CONFIG_DMA_BCM2708=y
-CONFIG_DMA_BCM2835=y
-CONFIG_DMA_CMA=y
-CONFIG_DMA_ENGINE=y
-CONFIG_DMA_OF=y
-CONFIG_DMA_VIRTUAL_CHANNELS=y
-CONFIG_DNOTIFY=y
-CONFIG_DTC=y
-CONFIG_DUMMY_CONSOLE=y
-CONFIG_EDAC_ATOMIC_SCRUB=y
-CONFIG_EDAC_SUPPORT=y
-CONFIG_ENABLE_MUST_CHECK=y
-CONFIG_EXT4_FS=y
-CONFIG_EXT4_FS_POSIX_ACL=y
-CONFIG_EXT4_FS_SECURITY=y
-CONFIG_FB=y
-CONFIG_FB_BCM2708=y
-CONFIG_FB_CFB_COPYAREA=y
-CONFIG_FB_CFB_FILLRECT=y
-CONFIG_FB_CFB_IMAGEBLIT=y
-CONFIG_FB_CMDLINE=y
-# CONFIG_FB_RPISENSE is not set
-CONFIG_FIQ=y
-CONFIG_FIRMWARE_IN_KERNEL=y
-CONFIG_FIX_EARLYCON_MEM=y
-# CONFIG_FONTS is not set
-CONFIG_FONT_8x16=y
-CONFIG_FONT_8x8=y
-CONFIG_FONT_SUPPORT=y
-# CONFIG_FPE_FASTFPE is not set
-# CONFIG_FPE_NWFPE is not set
-CONFIG_FRAMEBUFFER_CONSOLE=y
-# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
-# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
-CONFIG_FREEZER=y
-CONFIG_FS_MBCACHE=y
-CONFIG_FS_POSIX_ACL=y
-CONFIG_GENERIC_ALLOCATOR=y
-CONFIG_GENERIC_ATOMIC64=y
-CONFIG_GENERIC_BUG=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_GENERIC_IDLE_POLL_SETUP=y
-CONFIG_GENERIC_IO=y
-CONFIG_GENERIC_IRQ_SHOW=y
-CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
-CONFIG_GENERIC_PCI_IOMAP=y
-CONFIG_GENERIC_PINCONF=y
-CONFIG_GENERIC_SCHED_CLOCK=y
-CONFIG_GENERIC_SMP_IDLE_THREAD=y
-CONFIG_GENERIC_STRNCPY_FROM_USER=y
-CONFIG_GENERIC_STRNLEN_USER=y
-CONFIG_GPIOLIB=y
-# CONFIG_GPIO_BCM_VIRT is not set
-CONFIG_GPIO_DEVRES=y
-CONFIG_GPIO_SYSFS=y
-CONFIG_HANDLE_DOMAIN_IRQ=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT_MAP=y
-# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
-# CONFIG_HAVE_ARCH_BITREVERSE is not set
-CONFIG_HAVE_ARCH_JUMP_LABEL=y
-CONFIG_HAVE_ARCH_KGDB=y
-CONFIG_HAVE_ARCH_PFN_VALID=y
-CONFIG_HAVE_ARCH_TRACEHOOK=y
-# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
-CONFIG_HAVE_BPF_JIT=y
-CONFIG_HAVE_CC_STACKPROTECTOR=y
-CONFIG_HAVE_CLK=y
-CONFIG_HAVE_CLK_PREPARE=y
-CONFIG_HAVE_CONTEXT_TRACKING=y
-CONFIG_HAVE_C_RECORDMCOUNT=y
-CONFIG_HAVE_DEBUG_KMEMLEAK=y
-CONFIG_HAVE_DMA_API_DEBUG=y
-CONFIG_HAVE_DMA_ATTRS=y
-CONFIG_HAVE_DMA_CONTIGUOUS=y
-CONFIG_HAVE_DYNAMIC_FTRACE=y
-CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
-CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
-CONFIG_HAVE_FUNCTION_TRACER=y
-CONFIG_HAVE_GENERIC_DMA_COHERENT=y
-CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
-CONFIG_HAVE_KERNEL_GZIP=y
-CONFIG_HAVE_KERNEL_LZ4=y
-CONFIG_HAVE_KERNEL_LZMA=y
-CONFIG_HAVE_KERNEL_LZO=y
-CONFIG_HAVE_KERNEL_XZ=y
-CONFIG_HAVE_LATENCYTOP_SUPPORT=y
-CONFIG_HAVE_MEMBLOCK=y
-CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
-CONFIG_HAVE_NET_DSA=y
-CONFIG_HAVE_OPROFILE=y
-CONFIG_HAVE_OPTPROBES=y
-CONFIG_HAVE_PERF_EVENTS=y
-CONFIG_HAVE_PERF_REGS=y
-CONFIG_HAVE_PERF_USER_STACK_DUMP=y
-CONFIG_HAVE_PROC_CPU=y
-CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
-CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
-CONFIG_HAVE_UID16=y
-CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
-CONFIG_HW_CONSOLE=y
-CONFIG_HZ_FIXED=0
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_INPUT=y
-CONFIG_INPUT_MOUSEDEV=y
-# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
-CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
-CONFIG_IOMMU_HELPER=y
-CONFIG_IOSCHED_CFQ=y
-CONFIG_IRQCHIP=y
-CONFIG_IRQ_DOMAIN=y
-CONFIG_IRQ_FORCED_THREADING=y
-CONFIG_IRQ_WORK=y
-CONFIG_JBD2=y
-CONFIG_KERNEL_GZIP=y
-# CONFIG_KERNEL_XZ is not set
-# CONFIG_LCD_CLASS_DEVICE is not set
-CONFIG_LEDS_GPIO=y
-CONFIG_LEDS_TRIGGER_INPUT=y
-CONFIG_LIBFDT=y
-CONFIG_LOGO=y
-CONFIG_LOGO_LINUX_CLUT224=y
-# CONFIG_LOGO_LINUX_MONO is not set
-# CONFIG_LOGO_LINUX_VGA16 is not set
-CONFIG_MACH_BCM2708=y
-CONFIG_MAC_PARTITION=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_MAILBOX=y
-# CONFIG_MAILBOX_TEST is not set
-CONFIG_MAX_RAW_DEVS=256
-CONFIG_MEMORY_ISOLATION=y
-CONFIG_MIGRATION=y
-CONFIG_MMC=y
-CONFIG_MMC_BCM2835=y
-CONFIG_MMC_BCM2835_DMA=y
-CONFIG_MMC_BCM2835_PIO_DMA_BARRIER=2
-CONFIG_MMC_BCM2835_SDHOST=y
-CONFIG_MMC_BLOCK=y
-CONFIG_MMC_BLOCK_MINORS=32
-CONFIG_MMC_SDHCI=y
-CONFIG_MMC_SDHCI_PLTFM=y
-CONFIG_MODULES_USE_ELF_REL=y
-# CONFIG_MTD is not set
-CONFIG_MULTI_IRQ_HANDLER=y
-CONFIG_NEED_DMA_MAP_STATE=y
-CONFIG_NEED_MACH_IO_H=y
-CONFIG_NEED_MACH_MEMORY_H=y
-CONFIG_NEED_PER_CPU_KM=y
-CONFIG_NLS=y
-CONFIG_NLS_ASCII=y
-CONFIG_NLS_DEFAULT="utf8"
-CONFIG_NO_BOOTMEM=y
-CONFIG_NO_HZ=y
-CONFIG_NO_HZ_COMMON=y
-CONFIG_NO_HZ_IDLE=y
-CONFIG_OABI_COMPAT=y
-CONFIG_OF=y
-CONFIG_OF_ADDRESS=y
-CONFIG_OF_CONFIGFS=y
-CONFIG_OF_DYNAMIC=y
-CONFIG_OF_EARLY_FLATTREE=y
-CONFIG_OF_FLATTREE=y
-CONFIG_OF_GPIO=y
-CONFIG_OF_IRQ=y
-CONFIG_OF_NET=y
-CONFIG_OF_OVERLAY=y
-CONFIG_OF_RESERVED_MEM=y
-CONFIG_OF_RESOLVE=y
-CONFIG_OLD_SIGACTION=y
-CONFIG_OLD_SIGSUSPEND3=y
-CONFIG_PAGE_OFFSET=0xC0000000
-# CONFIG_PCI_DOMAINS_GENERIC is not set
-# CONFIG_PCI_SYSCALL is not set
-CONFIG_PERF_USE_VMALLOC=y
-CONFIG_PGTABLE_LEVELS=2
-CONFIG_PHYS_OFFSET=0
-CONFIG_PINCTRL=y
-CONFIG_PINCTRL_BCM2835=y
-# CONFIG_PL330_DMA is not set
-CONFIG_PM=y
-CONFIG_PM_CLK=y
-# CONFIG_PM_DEBUG is not set
-CONFIG_PM_GENERIC_DOMAINS=y
-CONFIG_PM_GENERIC_DOMAINS_OF=y
-CONFIG_PM_GENERIC_DOMAINS_SLEEP=y
-CONFIG_PM_SLEEP=y
-CONFIG_POWER_SUPPLY=y
-CONFIG_PRINTK_TIME=y
-CONFIG_PROC_PAGE_MONITOR=y
-CONFIG_PWM=y
-CONFIG_PWM_BCM2835=y
-CONFIG_PWM_SYSFS=y
-CONFIG_RASPBERRYPI_FIRMWARE=y
-CONFIG_RASPBERRYPI_POWER=y
-CONFIG_RATIONAL=y
-CONFIG_RAW_DRIVER=y
-# CONFIG_RCU_STALL_COMMON is not set
-CONFIG_RWSEM_XCHGADD_ALGORITHM=y
-CONFIG_SCHED_HRTICK=y
-# CONFIG_SCHED_INFO is not set
-CONFIG_SCSI=y
-# CONFIG_SCSI_LOWLEVEL is not set
-# CONFIG_SCSI_PROC_FS is not set
-# CONFIG_SERIAL_8250_DMA is not set
-CONFIG_SERIAL_8250_FSL=y
-CONFIG_SERIAL_8250_NR_UARTS=1
-CONFIG_SERIAL_8250_RUNTIME_UARTS=0
-# CONFIG_SERIAL_AMBA_PL010 is not set
-CONFIG_SERIAL_AMBA_PL011=y
-CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
-CONFIG_SERIAL_OF_PLATFORM=y
-CONFIG_SPARSE_IRQ=y
-# CONFIG_SQUASHFS is not set
-CONFIG_SRCU=y
-# CONFIG_STAGING is not set
-# CONFIG_STRIP_ASM_SYMS is not set
-CONFIG_SUSPEND=y
-CONFIG_SUSPEND_FREEZER=y
-CONFIG_SWIOTLB=y
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-# CONFIG_TEXTSEARCH is not set
-CONFIG_THERMAL=y
-CONFIG_THERMAL_BCM2835=y
-CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
-CONFIG_THERMAL_GOV_STEP_WISE=y
-CONFIG_THERMAL_OF=y
-CONFIG_TICK_CPU_ACCOUNTING=y
-CONFIG_TMPFS_POSIX_ACL=y
-CONFIG_UEVENT_HELPER_PATH=""
-# CONFIG_UID16 is not set
-CONFIG_UNCOMPRESS_INCLUDE="mach/uncompress.h"
-CONFIG_USB=y
-CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
-CONFIG_USB_COMMON=y
-CONFIG_USB_DWCOTG=y
-# CONFIG_USB_EHCI_HCD is not set
-CONFIG_USB_NET_DRIVERS=y
-CONFIG_USB_NET_SMSC95XX=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_SUPPORT=y
-CONFIG_USB_UAS=y
-CONFIG_USB_USBNET=y
-CONFIG_USE_OF=y
-CONFIG_VECTORS_BASE=0xffff0000
-CONFIG_VFP=y
-CONFIG_VT=y
-CONFIG_VT_CONSOLE=y
-CONFIG_VT_CONSOLE_SLEEP=y
-CONFIG_VT_HW_CONSOLE_BINDING=y
-CONFIG_WATCHDOG_CORE=y
-CONFIG_XZ_DEC_ARM=y
-CONFIG_XZ_DEC_BCJ=y
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZONE_DMA_FLAG=0
diff --git a/target/linux/brcm2708/bcm2709/config-4.4 b/target/linux/brcm2708/bcm2709/config-4.4
deleted file mode 100644
index 2aad7d9..0000000
--- a/target/linux/brcm2708/bcm2709/config-4.4
+++ /dev/null
@@ -1,396 +0,0 @@
-# CONFIG_AIO is not set
-CONFIG_ALIGNMENT_TRAP=y
-# CONFIG_AMBA_PL08X is not set
-# CONFIG_APM_EMULATION is not set
-# CONFIG_ARCH_BCM2708 is not set
-CONFIG_ARCH_BCM2709=y
-CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
-CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
-CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y
-# CONFIG_ARCH_HAS_SG_CHAIN is not set
-CONFIG_ARCH_HAS_TICK_BROADCAST=y
-CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
-CONFIG_ARCH_HIBERNATION_POSSIBLE=y
-CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
-CONFIG_ARCH_NR_GPIO=0
-CONFIG_ARCH_REQUIRE_GPIOLIB=y
-# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
-# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
-CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
-CONFIG_ARCH_SUPPORTS_UPROBES=y
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_ARCH_USE_BUILTIN_BSWAP=y
-CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y
-CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
-CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
-CONFIG_ARM=y
-CONFIG_ARM_AMBA=y
-CONFIG_ARM_ARCH_TIMER=y
-CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y
-CONFIG_ARM_CPU_SUSPEND=y
-CONFIG_ARM_L1_CACHE_SHIFT=6
-CONFIG_ARM_L1_CACHE_SHIFT_6=y
-# CONFIG_ARM_LPAE is not set
-# CONFIG_ARM_SP805_WATCHDOG is not set
-CONFIG_ARM_THUMB=y
-# CONFIG_ARM_THUMBEE is not set
-CONFIG_ARM_UNWIND=y
-CONFIG_ARM_VIRT_EXT=y
-# CONFIG_BACKLIGHT_CLASS_DEVICE is not set
-CONFIG_BACKLIGHT_LCD_SUPPORT=y
-CONFIG_BCM2708_NOL2CACHE=y
-CONFIG_BCM2708_VCHIQ=y
-CONFIG_BCM2708_VCMEM=y
-# CONFIG_BCM2835_DEVGPIOMEM is not set
-CONFIG_BCM2835_MBOX=y
-# CONFIG_BCM2835_SMI is not set
-CONFIG_BCM2835_WDT=y
-CONFIG_BCM_VCIO=y
-CONFIG_BCM_VC_CMA=y
-CONFIG_BCM_VC_SM=y
-# CONFIG_BLK_DEV_INITRD is not set
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_COUNT=16
-CONFIG_BLK_DEV_RAM_SIZE=4096
-CONFIG_BLK_DEV_SD=y
-CONFIG_BRCM_CHAR_DRIVERS=y
-CONFIG_BUILD_BIN2C=y
-# CONFIG_CACHE_L2X0 is not set
-CONFIG_CLKDEV_LOOKUP=y
-CONFIG_CLKSRC_OF=y
-CONFIG_CLKSRC_PROBE=y
-CONFIG_CLONE_BACKWARDS=y
-CONFIG_CMA=y
-CONFIG_CMA_ALIGNMENT=8
-CONFIG_CMA_AREAS=7
-# CONFIG_CMA_DEBUG is not set
-# CONFIG_CMA_DEBUGFS is not set
-CONFIG_CMA_SIZE_MBYTES=16
-# CONFIG_CMA_SIZE_SEL_MAX is not set
-CONFIG_CMA_SIZE_SEL_MBYTES=y
-# CONFIG_CMA_SIZE_SEL_MIN is not set
-# CONFIG_CMA_SIZE_SEL_PERCENTAGE is not set
-CONFIG_COMMON_CLK=y
-CONFIG_CONFIGFS_FS=y
-CONFIG_CONSOLE_TRANSLATIONS=y
-CONFIG_CPU_32v6K=y
-CONFIG_CPU_32v7=y
-CONFIG_CPU_ABRT_EV7=y
-# CONFIG_CPU_BPREDICT_DISABLE is not set
-CONFIG_CPU_CACHE_V7=y
-CONFIG_CPU_CACHE_VIPT=y
-CONFIG_CPU_COPY_V6=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-CONFIG_CPU_HAS_ASID=y
-# CONFIG_CPU_ICACHE_DISABLE is not set
-CONFIG_CPU_IDLE=y
-CONFIG_CPU_IDLE_GOV_LADDER=y
-CONFIG_CPU_IDLE_GOV_MENU=y
-CONFIG_CPU_PABRT_V7=y
-CONFIG_CPU_PM=y
-CONFIG_CPU_RMAP=y
-CONFIG_CPU_TLB_V7=y
-CONFIG_CPU_V7=y
-CONFIG_CRC16=y
-CONFIG_CRYPTO_CRC32C=y
-CONFIG_CRYPTO_HASH=y
-CONFIG_CRYPTO_HASH2=y
-CONFIG_CRYPTO_RNG2=y
-CONFIG_CRYPTO_WORKQUEUE=y
-CONFIG_DCACHE_WORD_ACCESS=y
-CONFIG_DEBUG_BUGVERBOSE=y
-CONFIG_DEBUG_INFO=y
-CONFIG_DEBUG_LL_INCLUDE="mach/debug-macro.S"
-# CONFIG_DEBUG_UART_8250 is not set
-# CONFIG_DEBUG_USER is not set
-CONFIG_DEFAULT_CFQ=y
-# CONFIG_DEFAULT_DEADLINE is not set
-CONFIG_DEFAULT_IOSCHED="cfq"
-CONFIG_DMADEVICES=y
-CONFIG_DMA_BCM2708=y
-CONFIG_DMA_BCM2835=y
-CONFIG_DMA_CMA=y
-CONFIG_DMA_ENGINE=y
-CONFIG_DMA_OF=y
-CONFIG_DMA_VIRTUAL_CHANNELS=y
-CONFIG_DNOTIFY=y
-CONFIG_DTC=y
-CONFIG_DUMMY_CONSOLE=y
-CONFIG_EDAC_ATOMIC_SCRUB=y
-CONFIG_EDAC_SUPPORT=y
-CONFIG_ENABLE_MUST_CHECK=y
-CONFIG_EXT4_FS=y
-CONFIG_EXT4_FS_POSIX_ACL=y
-CONFIG_EXT4_FS_SECURITY=y
-CONFIG_FB=y
-CONFIG_FB_BCM2708=y
-CONFIG_FB_CFB_COPYAREA=y
-CONFIG_FB_CFB_FILLRECT=y
-CONFIG_FB_CFB_IMAGEBLIT=y
-CONFIG_FB_CMDLINE=y
-# CONFIG_FB_RPISENSE is not set
-CONFIG_FIQ=y
-CONFIG_FIRMWARE_IN_KERNEL=y
-CONFIG_FIX_EARLYCON_MEM=y
-# CONFIG_FONTS is not set
-CONFIG_FONT_8x16=y
-CONFIG_FONT_8x8=y
-CONFIG_FONT_SUPPORT=y
-# CONFIG_FPE_FASTFPE is not set
-# CONFIG_FPE_NWFPE is not set
-CONFIG_FRAMEBUFFER_CONSOLE=y
-# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
-# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
-CONFIG_FREEZER=y
-CONFIG_FS_MBCACHE=y
-CONFIG_FS_POSIX_ACL=y
-CONFIG_GENERIC_ALLOCATOR=y
-CONFIG_GENERIC_BUG=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
-CONFIG_GENERIC_IDLE_POLL_SETUP=y
-CONFIG_GENERIC_IO=y
-CONFIG_GENERIC_IRQ_SHOW=y
-CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
-CONFIG_GENERIC_PCI_IOMAP=y
-CONFIG_GENERIC_PINCONF=y
-CONFIG_GENERIC_SCHED_CLOCK=y
-CONFIG_GENERIC_SMP_IDLE_THREAD=y
-CONFIG_GENERIC_STRNCPY_FROM_USER=y
-CONFIG_GENERIC_STRNLEN_USER=y
-CONFIG_GPIOLIB=y
-# CONFIG_GPIO_BCM_VIRT is not set
-CONFIG_GPIO_DEVRES=y
-CONFIG_GPIO_SYSFS=y
-CONFIG_HANDLE_DOMAIN_IRQ=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT_MAP=y
-# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
-CONFIG_HAVE_ARCH_BITREVERSE=y
-CONFIG_HAVE_ARCH_JUMP_LABEL=y
-CONFIG_HAVE_ARCH_KGDB=y
-CONFIG_HAVE_ARCH_PFN_VALID=y
-CONFIG_HAVE_ARCH_TRACEHOOK=y
-CONFIG_HAVE_ARM_ARCH_TIMER=y
-# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
-CONFIG_HAVE_BPF_JIT=y
-CONFIG_HAVE_CC_STACKPROTECTOR=y
-CONFIG_HAVE_CLK=y
-CONFIG_HAVE_CLK_PREPARE=y
-CONFIG_HAVE_CONTEXT_TRACKING=y
-CONFIG_HAVE_C_RECORDMCOUNT=y
-CONFIG_HAVE_DEBUG_KMEMLEAK=y
-CONFIG_HAVE_DMA_API_DEBUG=y
-CONFIG_HAVE_DMA_ATTRS=y
-CONFIG_HAVE_DMA_CONTIGUOUS=y
-CONFIG_HAVE_DYNAMIC_FTRACE=y
-CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
-CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
-CONFIG_HAVE_FUNCTION_TRACER=y
-CONFIG_HAVE_GENERIC_DMA_COHERENT=y
-CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
-CONFIG_HAVE_KERNEL_GZIP=y
-CONFIG_HAVE_KERNEL_LZ4=y
-CONFIG_HAVE_KERNEL_LZMA=y
-CONFIG_HAVE_KERNEL_LZO=y
-CONFIG_HAVE_KERNEL_XZ=y
-CONFIG_HAVE_MEMBLOCK=y
-CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
-CONFIG_HAVE_NET_DSA=y
-CONFIG_HAVE_OPROFILE=y
-CONFIG_HAVE_OPTPROBES=y
-CONFIG_HAVE_PERF_EVENTS=y
-CONFIG_HAVE_PERF_REGS=y
-CONFIG_HAVE_PERF_USER_STACK_DUMP=y
-CONFIG_HAVE_PROC_CPU=y
-CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
-CONFIG_HAVE_SMP=y
-CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
-CONFIG_HAVE_UID16=y
-CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
-CONFIG_HOTPLUG_CPU=y
-CONFIG_HW_CONSOLE=y
-CONFIG_HZ_FIXED=0
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_INPUT=y
-CONFIG_INPUT_MOUSEDEV=y
-# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
-CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
-CONFIG_IOMMU_HELPER=y
-CONFIG_IOSCHED_CFQ=y
-CONFIG_IRQCHIP=y
-CONFIG_IRQ_DOMAIN=y
-CONFIG_IRQ_FORCED_THREADING=y
-CONFIG_IRQ_WORK=y
-CONFIG_JBD2=y
-CONFIG_KERNEL_GZIP=y
-# CONFIG_KERNEL_XZ is not set
-# CONFIG_LCD_CLASS_DEVICE is not set
-CONFIG_LEDS_GPIO=y
-CONFIG_LEDS_TRIGGER_INPUT=y
-CONFIG_LIBFDT=y
-CONFIG_LOCK_SPIN_ON_OWNER=y
-CONFIG_LOGO=y
-CONFIG_LOGO_LINUX_CLUT224=y
-# CONFIG_LOGO_LINUX_MONO is not set
-# CONFIG_LOGO_LINUX_VGA16 is not set
-CONFIG_LZO_COMPRESS=y
-CONFIG_LZO_DECOMPRESS=y
-CONFIG_MACH_BCM2709=y
-CONFIG_MAC_PARTITION=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_MAILBOX=y
-# CONFIG_MAILBOX_TEST is not set
-CONFIG_MAX_RAW_DEVS=256
-CONFIG_MEMORY_ISOLATION=y
-CONFIG_MFD_SYSCON=y
-CONFIG_MIGHT_HAVE_CACHE_L2X0=y
-CONFIG_MIGRATION=y
-CONFIG_MMC=y
-CONFIG_MMC_BCM2835=y
-CONFIG_MMC_BCM2835_DMA=y
-CONFIG_MMC_BCM2835_PIO_DMA_BARRIER=2
-CONFIG_MMC_BCM2835_SDHOST=y
-CONFIG_MMC_BLOCK=y
-CONFIG_MMC_BLOCK_MINORS=32
-CONFIG_MMC_SDHCI=y
-CONFIG_MMC_SDHCI_PLTFM=y
-CONFIG_MODULES_USE_ELF_REL=y
-# CONFIG_MTD is not set
-CONFIG_MULTI_IRQ_HANDLER=y
-CONFIG_MUTEX_SPIN_ON_OWNER=y
-CONFIG_NEED_DMA_MAP_STATE=y
-CONFIG_NEED_MACH_IO_H=y
-CONFIG_NEED_MACH_MEMORY_H=y
-CONFIG_NEON=y
-CONFIG_NET_FLOW_LIMIT=y
-CONFIG_NLS=y
-CONFIG_NLS_ASCII=y
-CONFIG_NLS_DEFAULT="utf8"
-CONFIG_NO_BOOTMEM=y
-CONFIG_NO_HZ=y
-CONFIG_NO_HZ_COMMON=y
-CONFIG_NO_HZ_IDLE=y
-CONFIG_NR_CPUS=4
-CONFIG_OABI_COMPAT=y
-CONFIG_OF=y
-CONFIG_OF_ADDRESS=y
-CONFIG_OF_CONFIGFS=y
-CONFIG_OF_DYNAMIC=y
-CONFIG_OF_EARLY_FLATTREE=y
-CONFIG_OF_FLATTREE=y
-CONFIG_OF_GPIO=y
-CONFIG_OF_IRQ=y
-CONFIG_OF_NET=y
-CONFIG_OF_OVERLAY=y
-CONFIG_OF_RESERVED_MEM=y
-CONFIG_OF_RESOLVE=y
-CONFIG_OLD_SIGACTION=y
-CONFIG_OLD_SIGSUSPEND3=y
-CONFIG_PAGE_OFFSET=0x80000000
-# CONFIG_PCI_DOMAINS_GENERIC is not set
-# CONFIG_PCI_SYSCALL is not set
-CONFIG_PERF_USE_VMALLOC=y
-CONFIG_PGTABLE_LEVELS=2
-CONFIG_PHYS_OFFSET=0
-CONFIG_PINCTRL=y
-CONFIG_PINCTRL_BCM2835=y
-# CONFIG_PL330_DMA is not set
-CONFIG_PM=y
-CONFIG_PM_CLK=y
-# CONFIG_PM_DEBUG is not set
-CONFIG_PM_GENERIC_DOMAINS=y
-CONFIG_PM_GENERIC_DOMAINS_OF=y
-CONFIG_PM_GENERIC_DOMAINS_SLEEP=y
-CONFIG_PM_SLEEP=y
-CONFIG_PM_SLEEP_SMP=y
-CONFIG_POWER_SUPPLY=y
-CONFIG_PRINTK_TIME=y
-CONFIG_PROC_PAGE_MONITOR=y
-CONFIG_PWM=y
-CONFIG_PWM_BCM2835=y
-CONFIG_PWM_SYSFS=y
-CONFIG_RASPBERRYPI_FIRMWARE=y
-CONFIG_RASPBERRYPI_POWER=y
-CONFIG_RATIONAL=y
-CONFIG_RAW_DRIVER=y
-CONFIG_RCU_STALL_COMMON=y
-CONFIG_REGMAP=y
-CONFIG_REGMAP_MMIO=y
-CONFIG_RFS_ACCEL=y
-CONFIG_RPS=y
-CONFIG_RWSEM_SPIN_ON_OWNER=y
-CONFIG_RWSEM_XCHGADD_ALGORITHM=y
-CONFIG_SCHED_HRTICK=y
-# CONFIG_SCHED_INFO is not set
-CONFIG_SCSI=y
-# CONFIG_SCSI_LOWLEVEL is not set
-# CONFIG_SCSI_PROC_FS is not set
-# CONFIG_SERIAL_8250_DMA is not set
-CONFIG_SERIAL_8250_FSL=y
-CONFIG_SERIAL_8250_NR_UARTS=1
-CONFIG_SERIAL_8250_RUNTIME_UARTS=0
-# CONFIG_SERIAL_AMBA_PL010 is not set
-CONFIG_SERIAL_AMBA_PL011=y
-CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
-CONFIG_SERIAL_OF_PLATFORM=y
-CONFIG_SMP=y
-CONFIG_SMP_ON_UP=y
-CONFIG_SPARSE_IRQ=y
-# CONFIG_SQUASHFS is not set
-CONFIG_SRCU=y
-# CONFIG_STAGING is not set
-# CONFIG_STRIP_ASM_SYMS is not set
-CONFIG_SUSPEND=y
-CONFIG_SUSPEND_FREEZER=y
-CONFIG_SWIOTLB=y
-CONFIG_SWP_EMULATE=y
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-# CONFIG_TEXTSEARCH is not set
-CONFIG_THERMAL=y
-CONFIG_THERMAL_BCM2835=y
-CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
-CONFIG_THERMAL_GOV_STEP_WISE=y
-CONFIG_THERMAL_OF=y
-# CONFIG_THUMB2_KERNEL is not set
-CONFIG_TICK_CPU_ACCOUNTING=y
-CONFIG_TMPFS_POSIX_ACL=y
-CONFIG_TREE_RCU=y
-CONFIG_UEVENT_HELPER_PATH=""
-# CONFIG_UID16 is not set
-CONFIG_UNCOMPRESS_INCLUDE="mach/uncompress.h"
-CONFIG_USB=y
-CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
-CONFIG_USB_COMMON=y
-CONFIG_USB_DWCOTG=y
-# CONFIG_USB_EHCI_HCD is not set
-CONFIG_USB_NET_DRIVERS=y
-CONFIG_USB_NET_SMSC95XX=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_SUPPORT=y
-CONFIG_USB_UAS=y
-CONFIG_USB_USBNET=y
-CONFIG_USE_OF=y
-CONFIG_VECTORS_BASE=0xffff0000
-CONFIG_VFP=y
-CONFIG_VFPv3=y
-CONFIG_VMSPLIT_2G=y
-# CONFIG_VMSPLIT_3G is not set
-CONFIG_VT=y
-CONFIG_VT_CONSOLE=y
-CONFIG_VT_CONSOLE_SLEEP=y
-CONFIG_VT_HW_CONSOLE_BINDING=y
-CONFIG_WATCHDOG_CORE=y
-CONFIG_XPS=y
-CONFIG_XZ_DEC_ARM=y
-CONFIG_XZ_DEC_BCJ=y
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZONE_DMA_FLAG=0
diff --git a/target/linux/brcm2708/bcm2710/config-4.4 b/target/linux/brcm2708/bcm2710/config-4.4
deleted file mode 100644
index 5f2b76a..0000000
--- a/target/linux/brcm2708/bcm2710/config-4.4
+++ /dev/null
@@ -1,391 +0,0 @@
-# CONFIG_AIO is not set
-CONFIG_ALIGNMENT_TRAP=y
-# CONFIG_AMBA_PL08X is not set
-# CONFIG_APM_EMULATION is not set
-# CONFIG_ARCH_BCM2708 is not set
-CONFIG_ARCH_BCM2709=y
-CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
-CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
-CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y
-# CONFIG_ARCH_HAS_SG_CHAIN is not set
-CONFIG_ARCH_HAS_TICK_BROADCAST=y
-CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
-CONFIG_ARCH_HIBERNATION_POSSIBLE=y
-CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
-CONFIG_ARCH_NR_GPIO=0
-CONFIG_ARCH_REQUIRE_GPIOLIB=y
-# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
-# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
-CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
-CONFIG_ARCH_SUPPORTS_UPROBES=y
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_ARCH_USE_BUILTIN_BSWAP=y
-CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y
-CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
-CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
-CONFIG_ARM=y
-CONFIG_ARM_AMBA=y
-CONFIG_ARM_ARCH_TIMER=y
-CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y
-CONFIG_ARM_CPU_SUSPEND=y
-CONFIG_ARM_L1_CACHE_SHIFT=6
-CONFIG_ARM_L1_CACHE_SHIFT_6=y
-# CONFIG_ARM_LPAE is not set
-# CONFIG_ARM_SP805_WATCHDOG is not set
-CONFIG_ARM_THUMB=y
-# CONFIG_ARM_THUMBEE is not set
-CONFIG_ARM_UNWIND=y
-CONFIG_ARM_VIRT_EXT=y
-# CONFIG_BACKLIGHT_CLASS_DEVICE is not set
-CONFIG_BACKLIGHT_LCD_SUPPORT=y
-CONFIG_BCM2708_NOL2CACHE=y
-CONFIG_BCM2708_VCHIQ=y
-CONFIG_BCM2708_VCMEM=y
-# CONFIG_BCM2835_DEVGPIOMEM is not set
-CONFIG_BCM2835_MBOX=y
-# CONFIG_BCM2835_SMI is not set
-CONFIG_BCM2835_WDT=y
-CONFIG_BCM_VCIO=y
-CONFIG_BCM_VC_CMA=y
-CONFIG_BCM_VC_SM=y
-# CONFIG_BLK_DEV_INITRD is not set
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_COUNT=16
-CONFIG_BLK_DEV_RAM_SIZE=4096
-CONFIG_BLK_DEV_SD=y
-CONFIG_BRCM_CHAR_DRIVERS=y
-CONFIG_BUILD_BIN2C=y
-# CONFIG_CACHE_L2X0 is not set
-CONFIG_CLKDEV_LOOKUP=y
-CONFIG_CLKSRC_OF=y
-CONFIG_CLKSRC_PROBE=y
-CONFIG_CLONE_BACKWARDS=y
-CONFIG_CMA=y
-CONFIG_CMA_ALIGNMENT=8
-CONFIG_CMA_AREAS=7
-# CONFIG_CMA_DEBUG is not set
-# CONFIG_CMA_DEBUGFS is not set
-CONFIG_CMA_SIZE_MBYTES=16
-# CONFIG_CMA_SIZE_SEL_MAX is not set
-CONFIG_CMA_SIZE_SEL_MBYTES=y
-# CONFIG_CMA_SIZE_SEL_MIN is not set
-# CONFIG_CMA_SIZE_SEL_PERCENTAGE is not set
-CONFIG_COMMON_CLK=y
-CONFIG_CONFIGFS_FS=y
-CONFIG_CONSOLE_TRANSLATIONS=y
-CONFIG_CPU_32v6K=y
-CONFIG_CPU_32v7=y
-CONFIG_CPU_ABRT_EV7=y
-# CONFIG_CPU_BPREDICT_DISABLE is not set
-CONFIG_CPU_CACHE_V7=y
-CONFIG_CPU_CACHE_VIPT=y
-CONFIG_CPU_COPY_V6=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-CONFIG_CPU_HAS_ASID=y
-# CONFIG_CPU_ICACHE_DISABLE is not set
-CONFIG_CPU_IDLE=y
-CONFIG_CPU_IDLE_GOV_LADDER=y
-CONFIG_CPU_IDLE_GOV_MENU=y
-CONFIG_CPU_PABRT_V7=y
-CONFIG_CPU_PM=y
-CONFIG_CPU_RMAP=y
-CONFIG_CPU_TLB_V7=y
-CONFIG_CPU_V7=y
-CONFIG_CRC16=y
-CONFIG_CRYPTO_CRC32C=y
-CONFIG_CRYPTO_HASH=y
-CONFIG_CRYPTO_HASH2=y
-CONFIG_CRYPTO_RNG2=y
-CONFIG_CRYPTO_WORKQUEUE=y
-CONFIG_DCACHE_WORD_ACCESS=y
-CONFIG_DEBUG_BUGVERBOSE=y
-CONFIG_DEBUG_INFO=y
-CONFIG_DEBUG_LL_INCLUDE="mach/debug-macro.S"
-# CONFIG_DEBUG_UART_8250 is not set
-# CONFIG_DEBUG_USER is not set
-CONFIG_DEFAULT_CFQ=y
-# CONFIG_DEFAULT_DEADLINE is not set
-CONFIG_DEFAULT_IOSCHED="cfq"
-CONFIG_DMADEVICES=y
-CONFIG_DMA_BCM2708=y
-CONFIG_DMA_BCM2835=y
-CONFIG_DMA_CMA=y
-CONFIG_DMA_ENGINE=y
-CONFIG_DMA_OF=y
-CONFIG_DMA_VIRTUAL_CHANNELS=y
-CONFIG_DNOTIFY=y
-CONFIG_DTC=y
-CONFIG_DUMMY_CONSOLE=y
-CONFIG_EDAC_ATOMIC_SCRUB=y
-CONFIG_EDAC_SUPPORT=y
-CONFIG_ENABLE_MUST_CHECK=y
-CONFIG_EXT4_FS=y
-CONFIG_EXT4_FS_POSIX_ACL=y
-CONFIG_EXT4_FS_SECURITY=y
-CONFIG_FB=y
-CONFIG_FB_BCM2708=y
-CONFIG_FB_CFB_COPYAREA=y
-CONFIG_FB_CFB_FILLRECT=y
-CONFIG_FB_CFB_IMAGEBLIT=y
-CONFIG_FB_CMDLINE=y
-# CONFIG_FB_RPISENSE is not set
-CONFIG_FIQ=y
-CONFIG_FIRMWARE_IN_KERNEL=y
-CONFIG_FIX_EARLYCON_MEM=y
-# CONFIG_FONTS is not set
-CONFIG_FONT_8x16=y
-CONFIG_FONT_8x8=y
-CONFIG_FONT_SUPPORT=y
-# CONFIG_FPE_FASTFPE is not set
-# CONFIG_FPE_NWFPE is not set
-CONFIG_FRAMEBUFFER_CONSOLE=y
-# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
-# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
-CONFIG_FREEZER=y
-CONFIG_FS_MBCACHE=y
-CONFIG_FS_POSIX_ACL=y
-CONFIG_GENERIC_ALLOCATOR=y
-CONFIG_GENERIC_BUG=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
-CONFIG_GENERIC_IDLE_POLL_SETUP=y
-CONFIG_GENERIC_IO=y
-CONFIG_GENERIC_IRQ_SHOW=y
-CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
-CONFIG_GENERIC_PCI_IOMAP=y
-CONFIG_GENERIC_PINCONF=y
-CONFIG_GENERIC_SCHED_CLOCK=y
-CONFIG_GENERIC_SMP_IDLE_THREAD=y
-CONFIG_GENERIC_STRNCPY_FROM_USER=y
-CONFIG_GENERIC_STRNLEN_USER=y
-CONFIG_GPIOLIB=y
-CONFIG_GPIO_BCM_VIRT=y
-CONFIG_GPIO_DEVRES=y
-CONFIG_GPIO_SYSFS=y
-CONFIG_HANDLE_DOMAIN_IRQ=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT_MAP=y
-# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
-CONFIG_HAVE_ARCH_BITREVERSE=y
-CONFIG_HAVE_ARCH_JUMP_LABEL=y
-CONFIG_HAVE_ARCH_KGDB=y
-CONFIG_HAVE_ARCH_PFN_VALID=y
-CONFIG_HAVE_ARCH_TRACEHOOK=y
-CONFIG_HAVE_ARM_ARCH_TIMER=y
-# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
-CONFIG_HAVE_BPF_JIT=y
-CONFIG_HAVE_CC_STACKPROTECTOR=y
-CONFIG_HAVE_CLK=y
-CONFIG_HAVE_CLK_PREPARE=y
-CONFIG_HAVE_CONTEXT_TRACKING=y
-CONFIG_HAVE_C_RECORDMCOUNT=y
-CONFIG_HAVE_DEBUG_KMEMLEAK=y
-CONFIG_HAVE_DMA_API_DEBUG=y
-CONFIG_HAVE_DMA_ATTRS=y
-CONFIG_HAVE_DMA_CONTIGUOUS=y
-CONFIG_HAVE_DYNAMIC_FTRACE=y
-CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
-CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
-CONFIG_HAVE_FUNCTION_TRACER=y
-CONFIG_HAVE_GENERIC_DMA_COHERENT=y
-CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
-CONFIG_HAVE_MEMBLOCK=y
-CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
-CONFIG_HAVE_NET_DSA=y
-CONFIG_HAVE_OPROFILE=y
-CONFIG_HAVE_OPTPROBES=y
-CONFIG_HAVE_PERF_EVENTS=y
-CONFIG_HAVE_PERF_REGS=y
-CONFIG_HAVE_PERF_USER_STACK_DUMP=y
-CONFIG_HAVE_PROC_CPU=y
-CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
-CONFIG_HAVE_SMP=y
-CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
-CONFIG_HAVE_UID16=y
-CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
-CONFIG_HOTPLUG_CPU=y
-CONFIG_HW_CONSOLE=y
-CONFIG_HZ_FIXED=0
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_INPUT=y
-CONFIG_INPUT_MOUSEDEV=y
-# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
-CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
-CONFIG_IOMMU_HELPER=y
-CONFIG_IOSCHED_CFQ=y
-CONFIG_IRQCHIP=y
-CONFIG_IRQ_DOMAIN=y
-CONFIG_IRQ_FORCED_THREADING=y
-CONFIG_IRQ_WORK=y
-CONFIG_JBD2=y
-CONFIG_KERNEL_GZIP=y
-# CONFIG_KERNEL_XZ is not set
-# CONFIG_LCD_CLASS_DEVICE is not set
-CONFIG_LEDS_GPIO=y
-CONFIG_LEDS_TRIGGER_INPUT=y
-CONFIG_LIBFDT=y
-CONFIG_LOCK_SPIN_ON_OWNER=y
-CONFIG_LOGO=y
-CONFIG_LOGO_LINUX_CLUT224=y
-# CONFIG_LOGO_LINUX_MONO is not set
-# CONFIG_LOGO_LINUX_VGA16 is not set
-CONFIG_LZO_COMPRESS=y
-CONFIG_LZO_DECOMPRESS=y
-CONFIG_MACH_BCM2709=y
-CONFIG_MAC_PARTITION=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_MAILBOX=y
-# CONFIG_MAILBOX_TEST is not set
-CONFIG_MAX_RAW_DEVS=256
-CONFIG_MEMORY_ISOLATION=y
-CONFIG_MFD_SYSCON=y
-CONFIG_MIGHT_HAVE_CACHE_L2X0=y
-CONFIG_MIGRATION=y
-CONFIG_MMC=y
-CONFIG_MMC_BCM2835=y
-CONFIG_MMC_BCM2835_DMA=y
-CONFIG_MMC_BCM2835_PIO_DMA_BARRIER=2
-CONFIG_MMC_BCM2835_SDHOST=y
-CONFIG_MMC_BLOCK=y
-CONFIG_MMC_BLOCK_MINORS=32
-CONFIG_MMC_SDHCI=y
-CONFIG_MMC_SDHCI_PLTFM=y
-CONFIG_MODULES_USE_ELF_REL=y
-# CONFIG_MTD is not set
-CONFIG_MULTI_IRQ_HANDLER=y
-CONFIG_MUTEX_SPIN_ON_OWNER=y
-CONFIG_NEED_DMA_MAP_STATE=y
-CONFIG_NEED_MACH_IO_H=y
-CONFIG_NEED_MACH_MEMORY_H=y
-CONFIG_NEON=y
-CONFIG_NET_FLOW_LIMIT=y
-CONFIG_NLS=y
-CONFIG_NLS_ASCII=y
-CONFIG_NLS_DEFAULT="utf8"
-CONFIG_NO_BOOTMEM=y
-CONFIG_NO_HZ=y
-CONFIG_NO_HZ_COMMON=y
-CONFIG_NO_HZ_IDLE=y
-CONFIG_NR_CPUS=4
-CONFIG_OABI_COMPAT=y
-CONFIG_OF=y
-CONFIG_OF_ADDRESS=y
-CONFIG_OF_CONFIGFS=y
-CONFIG_OF_DYNAMIC=y
-CONFIG_OF_EARLY_FLATTREE=y
-CONFIG_OF_FLATTREE=y
-CONFIG_OF_GPIO=y
-CONFIG_OF_IRQ=y
-CONFIG_OF_NET=y
-CONFIG_OF_OVERLAY=y
-CONFIG_OF_RESERVED_MEM=y
-CONFIG_OF_RESOLVE=y
-CONFIG_OLD_SIGACTION=y
-CONFIG_OLD_SIGSUSPEND3=y
-CONFIG_PAGE_OFFSET=0x80000000
-# CONFIG_PCI_DOMAINS_GENERIC is not set
-# CONFIG_PCI_SYSCALL is not set
-CONFIG_PERF_USE_VMALLOC=y
-CONFIG_PGTABLE_LEVELS=2
-CONFIG_PHYS_OFFSET=0
-CONFIG_PINCTRL=y
-CONFIG_PINCTRL_BCM2835=y
-# CONFIG_PL330_DMA is not set
-CONFIG_PM=y
-CONFIG_PM_CLK=y
-# CONFIG_PM_DEBUG is not set
-CONFIG_PM_GENERIC_DOMAINS=y
-CONFIG_PM_GENERIC_DOMAINS_OF=y
-CONFIG_PM_GENERIC_DOMAINS_SLEEP=y
-CONFIG_PM_SLEEP=y
-CONFIG_PM_SLEEP_SMP=y
-CONFIG_POWER_SUPPLY=y
-CONFIG_PRINTK_TIME=y
-CONFIG_PROC_PAGE_MONITOR=y
-CONFIG_PWM=y
-CONFIG_PWM_BCM2835=y
-CONFIG_PWM_SYSFS=y
-CONFIG_RASPBERRYPI_FIRMWARE=y
-CONFIG_RASPBERRYPI_POWER=y
-CONFIG_RATIONAL=y
-CONFIG_RAW_DRIVER=y
-CONFIG_RCU_STALL_COMMON=y
-CONFIG_REGMAP=y
-CONFIG_REGMAP_MMIO=y
-CONFIG_RFS_ACCEL=y
-CONFIG_RPS=y
-CONFIG_RWSEM_SPIN_ON_OWNER=y
-CONFIG_RWSEM_XCHGADD_ALGORITHM=y
-CONFIG_SCHED_HRTICK=y
-# CONFIG_SCHED_INFO is not set
-CONFIG_SCSI=y
-# CONFIG_SCSI_LOWLEVEL is not set
-# CONFIG_SCSI_PROC_FS is not set
-# CONFIG_SERIAL_8250_DMA is not set
-CONFIG_SERIAL_8250_FSL=y
-CONFIG_SERIAL_8250_NR_UARTS=1
-CONFIG_SERIAL_8250_RUNTIME_UARTS=0
-# CONFIG_SERIAL_AMBA_PL010 is not set
-CONFIG_SERIAL_AMBA_PL011=y
-CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
-CONFIG_SERIAL_OF_PLATFORM=y
-CONFIG_SMP=y
-CONFIG_SMP_ON_UP=y
-CONFIG_SPARSE_IRQ=y
-# CONFIG_SQUASHFS is not set
-CONFIG_SRCU=y
-# CONFIG_STAGING is not set
-# CONFIG_STRIP_ASM_SYMS is not set
-CONFIG_SUSPEND=y
-CONFIG_SUSPEND_FREEZER=y
-CONFIG_SWIOTLB=y
-CONFIG_SWP_EMULATE=y
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-# CONFIG_TEXTSEARCH is not set
-CONFIG_THERMAL=y
-CONFIG_THERMAL_BCM2835=y
-CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
-CONFIG_THERMAL_GOV_STEP_WISE=y
-CONFIG_THERMAL_OF=y
-# CONFIG_THUMB2_KERNEL is not set
-CONFIG_TICK_CPU_ACCOUNTING=y
-CONFIG_TMPFS_POSIX_ACL=y
-CONFIG_TREE_RCU=y
-CONFIG_UEVENT_HELPER_PATH=""
-# CONFIG_UID16 is not set
-CONFIG_UNCOMPRESS_INCLUDE="mach/uncompress.h"
-CONFIG_USB=y
-CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
-CONFIG_USB_COMMON=y
-CONFIG_USB_DWCOTG=y
-# CONFIG_USB_EHCI_HCD is not set
-CONFIG_USB_NET_DRIVERS=y
-CONFIG_USB_NET_SMSC95XX=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_SUPPORT=y
-CONFIG_USB_UAS=y
-CONFIG_USB_USBNET=y
-CONFIG_USE_OF=y
-CONFIG_VECTORS_BASE=0xffff0000
-CONFIG_VFP=y
-CONFIG_VFPv3=y
-CONFIG_VMSPLIT_2G=y
-# CONFIG_VMSPLIT_3G is not set
-CONFIG_VT=y
-CONFIG_VT_CONSOLE=y
-CONFIG_VT_CONSOLE_SLEEP=y
-CONFIG_VT_HW_CONSOLE_BINDING=y
-CONFIG_WATCHDOG_CORE=y
-CONFIG_XPS=y
-CONFIG_XZ_DEC_ARM=y
-CONFIG_XZ_DEC_BCJ=y
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZONE_DMA_FLAG=0
diff --git a/target/linux/brcm2708/patches-4.4/0001-smsx95xx-fix-crimes-against-truesize.patch b/target/linux/brcm2708/patches-4.4/0001-smsx95xx-fix-crimes-against-truesize.patch
deleted file mode 100644
index 0594c64..0000000
--- a/target/linux/brcm2708/patches-4.4/0001-smsx95xx-fix-crimes-against-truesize.patch
+++ /dev/null
@@ -1,33 +0,0 @@
-From 5e0a05acf8d39aa7ad56c3c4e3fadfeb75770244 Mon Sep 17 00:00:00 2001
-From: Steve Glendinning <steve.glendinning at smsc.com>
-Date: Thu, 19 Feb 2015 18:47:12 +0000
-Subject: [PATCH] smsx95xx: fix crimes against truesize
-
-smsc95xx is adjusting truesize when it shouldn't, and following a recent patch from Eric this is now triggering warnings.
-
-This patch stops smsc95xx from changing truesize.
-
-Signed-off-by: Steve Glendinning <steve.glendinning at smsc.com>
----
- drivers/net/usb/smsc95xx.c | 2 --
- 1 file changed, 2 deletions(-)
- mode change 100644 => 100755 drivers/net/usb/smsc95xx.c
-
---- a/drivers/net/usb/smsc95xx.c
-+++ b/drivers/net/usb/smsc95xx.c
-@@ -1785,7 +1785,6 @@ static int smsc95xx_rx_fixup(struct usbn
- if (dev->net->features & NETIF_F_RXCSUM)
- smsc95xx_rx_csum_offload(skb);
- skb_trim(skb, skb->len - 4); /* remove fcs */
-- skb->truesize = size + sizeof(struct sk_buff);
-
- return 1;
- }
-@@ -1803,7 +1802,6 @@ static int smsc95xx_rx_fixup(struct usbn
- if (dev->net->features & NETIF_F_RXCSUM)
- smsc95xx_rx_csum_offload(ax_skb);
- skb_trim(ax_skb, ax_skb->len - 4); /* remove fcs */
-- ax_skb->truesize = size + sizeof(struct sk_buff);
-
- usbnet_skb_return(dev, ax_skb);
- }
diff --git a/target/linux/brcm2708/patches-4.4/0002-smsc95xx-Disable-turbo-mode-by-default.patch b/target/linux/brcm2708/patches-4.4/0002-smsc95xx-Disable-turbo-mode-by-default.patch
deleted file mode 100644
index 71e8a35..0000000
--- a/target/linux/brcm2708/patches-4.4/0002-smsc95xx-Disable-turbo-mode-by-default.patch
+++ /dev/null
@@ -1,20 +0,0 @@
-From 338345265d1f5941fb7814de74213ad610256ee8 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Fri, 17 Apr 2015 16:58:45 +0100
-Subject: [PATCH] smsc95xx: Disable turbo mode by default
-
----
- drivers/net/usb/smsc95xx.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/net/usb/smsc95xx.c
-+++ b/drivers/net/usb/smsc95xx.c
-@@ -70,7 +70,7 @@ struct smsc95xx_priv {
- u8 suspend_flags;
- };
-
--static bool turbo_mode = true;
-+static bool turbo_mode = false;
- module_param(turbo_mode, bool, 0644);
- MODULE_PARM_DESC(turbo_mode, "Enable multiple frames per Rx transaction");
-
diff --git a/target/linux/brcm2708/patches-4.4/0003-vmstat-Workaround-for-issue-where-dirty-page-count-g.patch b/target/linux/brcm2708/patches-4.4/0003-vmstat-Workaround-for-issue-where-dirty-page-count-g.patch
deleted file mode 100644
index f77ad92..0000000
--- a/target/linux/brcm2708/patches-4.4/0003-vmstat-Workaround-for-issue-where-dirty-page-count-g.patch
+++ /dev/null
@@ -1,27 +0,0 @@
-From dbe73fef550bcd1eedfb34be5600f9b87e7d1fe8 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Wed, 18 Jun 2014 13:42:01 +0100
-Subject: [PATCH] vmstat: Workaround for issue where dirty page count goes
- negative
-
-See:
-https://github.com/raspberrypi/linux/issues/617
-http://www.spinics.net/lists/linux-mm/msg72236.html
----
- include/linux/vmstat.h | 4 ++++
- 1 file changed, 4 insertions(+)
-
---- a/include/linux/vmstat.h
-+++ b/include/linux/vmstat.h
-@@ -219,7 +219,11 @@ static inline void __inc_zone_state(stru
- static inline void __dec_zone_state(struct zone *zone, enum zone_stat_item item)
- {
- atomic_long_dec(&zone->vm_stat[item]);
-+ if (item == NR_FILE_DIRTY && unlikely(atomic_long_read(&zone->vm_stat[item]) < 0))
-+ atomic_long_set(&zone->vm_stat[item], 0);
- atomic_long_dec(&vm_stat[item]);
-+ if (item == NR_FILE_DIRTY && unlikely(atomic_long_read(&vm_stat[item]) < 0))
-+ atomic_long_set(&vm_stat[item], 0);
- }
-
- static inline void __inc_zone_page_state(struct page *page,
diff --git a/target/linux/brcm2708/patches-4.4/0004-BCM2835_DT-Fix-I2S-register-map.patch b/target/linux/brcm2708/patches-4.4/0004-BCM2835_DT-Fix-I2S-register-map.patch
deleted file mode 100644
index ae4c145..0000000
--- a/target/linux/brcm2708/patches-4.4/0004-BCM2835_DT-Fix-I2S-register-map.patch
+++ /dev/null
@@ -1,50 +0,0 @@
-From 77886db55c4fcad9de44486e0e5e370d123d81bc Mon Sep 17 00:00:00 2001
-From: Robert Tiemann <rtie at gmx.de>
-Date: Mon, 20 Jul 2015 11:01:25 +0200
-Subject: [PATCH] BCM2835_DT: Fix I2S register map
-
----
- Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt | 4 ++--
- Documentation/devicetree/bindings/sound/brcm,bcm2835-i2s.txt | 4 ++--
- arch/arm/boot/dts/bcm2835.dtsi | 4 ++--
- 3 files changed, 6 insertions(+), 6 deletions(-)
-
---- a/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt
-+++ b/Documentation/devicetree/bindings/dma/brcm,bcm2835-dma.txt
-@@ -48,8 +48,8 @@ Example:
-
- bcm2835_i2s: i2s at 7e203000 {
- compatible = "brcm,bcm2835-i2s";
-- reg = < 0x7e203000 0x20>,
-- < 0x7e101098 0x02>;
-+ reg = < 0x7e203000 0x24>,
-+ < 0x7e101098 0x08>;
-
- dmas = <&dma 2>,
- <&dma 3>;
---- a/Documentation/devicetree/bindings/sound/brcm,bcm2835-i2s.txt
-+++ b/Documentation/devicetree/bindings/sound/brcm,bcm2835-i2s.txt
-@@ -16,8 +16,8 @@ Example:
-
- bcm2835_i2s: i2s at 7e203000 {
- compatible = "brcm,bcm2835-i2s";
-- reg = <0x7e203000 0x20>,
-- <0x7e101098 0x02>;
-+ reg = <0x7e203000 0x24>,
-+ <0x7e101098 0x08>;
-
- dmas = <&dma 2>,
- <&dma 3>;
---- a/arch/arm/boot/dts/bcm2835.dtsi
-+++ b/arch/arm/boot/dts/bcm2835.dtsi
-@@ -120,8 +120,8 @@
-
- i2s: i2s at 7e203000 {
- compatible = "brcm,bcm2835-i2s";
-- reg = <0x7e203000 0x20>,
-- <0x7e101098 0x02>;
-+ reg = <0x7e203000 0x24>,
-+ <0x7e101098 0x08>;
-
- dmas = <&dma 2>,
- <&dma 3>;
diff --git a/target/linux/brcm2708/patches-4.4/0005-irq-bcm2836-Prevent-spurious-interrupts-and-trap-the.patch b/target/linux/brcm2708/patches-4.4/0005-irq-bcm2836-Prevent-spurious-interrupts-and-trap-the.patch
deleted file mode 100644
index 5031f75..0000000
--- a/target/linux/brcm2708/patches-4.4/0005-irq-bcm2836-Prevent-spurious-interrupts-and-trap-the.patch
+++ /dev/null
@@ -1,30 +0,0 @@
-From c384d8900be3c3a0aba65f9538006280545264ba Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 4 Dec 2015 17:41:50 +0000
-Subject: [PATCH] irq-bcm2836: Prevent spurious interrupts, and trap them early
-
-The old arch-specific IRQ macros included a dsb to ensure the
-write to clear the mailbox interrupt completed before returning
-from the interrupt. The BCM2836 irqchip driver needs the same
-precaution to avoid spurious interrupts.
-
-Spurious interrupts are still possible for other reasons,
-though, so trap them early.
----
- drivers/irqchip/irq-bcm2836.c | 3 ++-
- 1 file changed, 2 insertions(+), 1 deletion(-)
-
---- a/drivers/irqchip/irq-bcm2836.c
-+++ b/drivers/irqchip/irq-bcm2836.c
-@@ -170,9 +170,10 @@ __exception_irq_entry bcm2836_arm_irqchi
- u32 ipi = ffs(mbox_val) - 1;
-
- writel(1 << ipi, mailbox0);
-+ dsb();
- handle_IPI(ipi, regs);
- #endif
-- } else {
-+ } else if (stat) {
- u32 hwirq = ffs(stat) - 1;
-
- handle_IRQ(irq_linear_revmap(intc.domain, hwirq), regs);
diff --git a/target/linux/brcm2708/patches-4.4/0006-irqchip-bcm2835-Add-FIQ-support.patch b/target/linux/brcm2708/patches-4.4/0006-irqchip-bcm2835-Add-FIQ-support.patch
deleted file mode 100644
index 0082f9c..0000000
--- a/target/linux/brcm2708/patches-4.4/0006-irqchip-bcm2835-Add-FIQ-support.patch
+++ /dev/null
@@ -1,127 +0,0 @@
-From f1b936ca7898183e0777012f57c8e5cafdda8be1 Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Noralf=20Tr=C3=B8nnes?= <noralf at tronnes.org>
-Date: Fri, 12 Jun 2015 19:01:05 +0200
-Subject: [PATCH] irqchip: bcm2835: Add FIQ support
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Add a duplicate irq range with an offset on the hwirq's so the
-driver can detect that enable_fiq() is used.
-Tested with downstream dwc_otg USB controller driver.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-Acked-by: Stephen Warren <swarren at wwwdotorg.org>
----
- arch/arm/mach-bcm/Kconfig | 1 +
- drivers/irqchip/irq-bcm2835.c | 51 ++++++++++++++++++++++++++++++++++++++-----
- 2 files changed, 47 insertions(+), 5 deletions(-)
-
---- a/arch/arm/mach-bcm/Kconfig
-+++ b/arch/arm/mach-bcm/Kconfig
-@@ -128,6 +128,7 @@ config ARCH_BCM2835
- select ARM_ERRATA_411920
- select ARM_TIMER_SP804
- select CLKSRC_OF
-+ select FIQ
- select PINCTRL
- select PINCTRL_BCM2835
- help
---- a/drivers/irqchip/irq-bcm2835.c
-+++ b/drivers/irqchip/irq-bcm2835.c
-@@ -55,7 +55,7 @@
- #include <asm/mach/irq.h>
-
- /* Put the bank and irq (32 bits) into the hwirq */
--#define MAKE_HWIRQ(b, n) ((b << 5) | (n))
-+#define MAKE_HWIRQ(b, n) (((b) << 5) | (n))
- #define HWIRQ_BANK(i) (i >> 5)
- #define HWIRQ_BIT(i) BIT(i & 0x1f)
-
-@@ -71,9 +71,13 @@
- | SHORTCUT1_MASK | SHORTCUT2_MASK)
-
- #define REG_FIQ_CONTROL 0x0c
-+#define REG_FIQ_ENABLE 0x80
-+#define REG_FIQ_DISABLE 0
-
- #define NR_BANKS 3
- #define IRQS_PER_BANK 32
-+#define NUMBER_IRQS MAKE_HWIRQ(NR_BANKS, 0)
-+#define FIQ_START (NR_IRQS_BANK0 + MAKE_HWIRQ(NR_BANKS - 1, 0))
-
- static const int reg_pending[] __initconst = { 0x00, 0x04, 0x08 };
- static const int reg_enable[] __initconst = { 0x18, 0x10, 0x14 };
-@@ -98,14 +102,38 @@ static void __exception_irq_entry bcm283
- struct pt_regs *regs);
- static void bcm2836_chained_handle_irq(struct irq_desc *desc);
-
-+static inline unsigned int hwirq_to_fiq(unsigned long hwirq)
-+{
-+ hwirq -= NUMBER_IRQS;
-+ /*
-+ * The hwirq numbering used in this driver is:
-+ * BASE (0-7) GPU1 (32-63) GPU2 (64-95).
-+ * This differ from the one used in the FIQ register:
-+ * GPU1 (0-31) GPU2 (32-63) BASE (64-71)
-+ */
-+ if (hwirq >= 32)
-+ return hwirq - 32;
-+
-+ return hwirq + 64;
-+}
-+
- static void armctrl_mask_irq(struct irq_data *d)
- {
-- writel_relaxed(HWIRQ_BIT(d->hwirq), intc.disable[HWIRQ_BANK(d->hwirq)]);
-+ if (d->hwirq >= NUMBER_IRQS)
-+ writel_relaxed(REG_FIQ_DISABLE, intc.base + REG_FIQ_CONTROL);
-+ else
-+ writel_relaxed(HWIRQ_BIT(d->hwirq),
-+ intc.disable[HWIRQ_BANK(d->hwirq)]);
- }
-
- static void armctrl_unmask_irq(struct irq_data *d)
- {
-- writel_relaxed(HWIRQ_BIT(d->hwirq), intc.enable[HWIRQ_BANK(d->hwirq)]);
-+ if (d->hwirq >= NUMBER_IRQS)
-+ writel_relaxed(REG_FIQ_ENABLE | hwirq_to_fiq(d->hwirq),
-+ intc.base + REG_FIQ_CONTROL);
-+ else
-+ writel_relaxed(HWIRQ_BIT(d->hwirq),
-+ intc.enable[HWIRQ_BANK(d->hwirq)]);
- }
-
- static struct irq_chip armctrl_chip = {
-@@ -151,8 +179,9 @@ static int __init armctrl_of_init(struct
- panic("%s: unable to map IC registers\n",
- node->full_name);
-
-- intc.domain = irq_domain_add_linear(node, MAKE_HWIRQ(NR_BANKS, 0),
-- &armctrl_ops, NULL);
-+ intc.base = base;
-+ intc.domain = irq_domain_add_linear(node, NUMBER_IRQS * 2,
-+ &armctrl_ops, NULL);
- if (!intc.domain)
- panic("%s: unable to create IRQ domain\n", node->full_name);
-
-@@ -182,6 +211,18 @@ static int __init armctrl_of_init(struct
- set_handle_irq(bcm2835_handle_irq);
- }
-
-+ /* Make a duplicate irq range which is used to enable FIQ */
-+ for (b = 0; b < NR_BANKS; b++) {
-+ for (i = 0; i < bank_irqs[b]; i++) {
-+ irq = irq_create_mapping(intc.domain,
-+ MAKE_HWIRQ(b, i) + NUMBER_IRQS);
-+ BUG_ON(irq <= 0);
-+ irq_set_chip(irq, &armctrl_chip);
-+ set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
-+ }
-+ }
-+ init_FIQ(FIQ_START);
-+
- return 0;
- }
-
diff --git a/target/linux/brcm2708/patches-4.4/0007-irqchip-irq-bcm2835-Add-2836-FIQ-support.patch b/target/linux/brcm2708/patches-4.4/0007-irqchip-irq-bcm2835-Add-2836-FIQ-support.patch
deleted file mode 100644
index 64faf32..0000000
--- a/target/linux/brcm2708/patches-4.4/0007-irqchip-irq-bcm2835-Add-2836-FIQ-support.patch
+++ /dev/null
@@ -1,96 +0,0 @@
-From e146ad89ce6f3d12fbaea2c2256c89ef991ea94d Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Noralf=20Tr=C3=B8nnes?= <noralf at tronnes.org>
-Date: Fri, 23 Oct 2015 16:26:55 +0200
-Subject: [PATCH] irqchip: irq-bcm2835: Add 2836 FIQ support
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
----
- drivers/irqchip/irq-bcm2835.c | 42 ++++++++++++++++++++++++++++++++++++++++--
- 1 file changed, 40 insertions(+), 2 deletions(-)
-
---- a/drivers/irqchip/irq-bcm2835.c
-+++ b/drivers/irqchip/irq-bcm2835.c
-@@ -50,6 +50,8 @@
- #include <linux/of_irq.h>
- #include <linux/irqchip.h>
- #include <linux/irqdomain.h>
-+#include <linux/mfd/syscon.h>
-+#include <linux/regmap.h>
-
- #include <asm/exception.h>
- #include <asm/mach/irq.h>
-@@ -70,6 +72,9 @@
- #define BANK0_VALID_MASK (BANK0_HWIRQ_MASK | BANK1_HWIRQ | BANK2_HWIRQ \
- | SHORTCUT1_MASK | SHORTCUT2_MASK)
-
-+#undef ARM_LOCAL_GPU_INT_ROUTING
-+#define ARM_LOCAL_GPU_INT_ROUTING 0x0c
-+
- #define REG_FIQ_CONTROL 0x0c
- #define REG_FIQ_ENABLE 0x80
- #define REG_FIQ_DISABLE 0
-@@ -95,6 +100,7 @@ struct armctrl_ic {
- void __iomem *enable[NR_BANKS];
- void __iomem *disable[NR_BANKS];
- struct irq_domain *domain;
-+ struct regmap *local_regmap;
- };
-
- static struct armctrl_ic intc __read_mostly;
-@@ -128,12 +134,35 @@ static void armctrl_mask_irq(struct irq_
-
- static void armctrl_unmask_irq(struct irq_data *d)
- {
-- if (d->hwirq >= NUMBER_IRQS)
-+ if (d->hwirq >= NUMBER_IRQS) {
-+ if (num_online_cpus() > 1) {
-+ unsigned int data;
-+ int ret;
-+
-+ if (!intc.local_regmap) {
-+ pr_err("FIQ is disabled due to missing regmap\n");
-+ return;
-+ }
-+
-+ ret = regmap_read(intc.local_regmap,
-+ ARM_LOCAL_GPU_INT_ROUTING, &data);
-+ if (ret) {
-+ pr_err("Failed to read int routing %d\n", ret);
-+ return;
-+ }
-+
-+ data &= ~0xc;
-+ data |= (1 << 2);
-+ regmap_write(intc.local_regmap,
-+ ARM_LOCAL_GPU_INT_ROUTING, data);
-+ }
-+
- writel_relaxed(REG_FIQ_ENABLE | hwirq_to_fiq(d->hwirq),
- intc.base + REG_FIQ_CONTROL);
-- else
-+ } else {
- writel_relaxed(HWIRQ_BIT(d->hwirq),
- intc.enable[HWIRQ_BANK(d->hwirq)]);
-+ }
- }
-
- static struct irq_chip armctrl_chip = {
-@@ -211,6 +240,15 @@ static int __init armctrl_of_init(struct
- set_handle_irq(bcm2835_handle_irq);
- }
-
-+ if (is_2836) {
-+ intc.local_regmap =
-+ syscon_regmap_lookup_by_compatible("brcm,bcm2836-arm-local");
-+ if (IS_ERR(intc.local_regmap)) {
-+ pr_err("Failed to get local register map. FIQ is disabled for cpus > 1\n");
-+ intc.local_regmap = NULL;
-+ }
-+ }
-+
- /* Make a duplicate irq range which is used to enable FIQ */
- for (b = 0; b < NR_BANKS; b++) {
- for (i = 0; i < bank_irqs[b]; i++) {
diff --git a/target/linux/brcm2708/patches-4.4/0008-serial-8250-Don-t-crash-when-nr_uarts-is-0.patch b/target/linux/brcm2708/patches-4.4/0008-serial-8250-Don-t-crash-when-nr_uarts-is-0.patch
deleted file mode 100644
index 6a271c8..0000000
--- a/target/linux/brcm2708/patches-4.4/0008-serial-8250-Don-t-crash-when-nr_uarts-is-0.patch
+++ /dev/null
@@ -1,20 +0,0 @@
-From 2a1cd53412d5cd5f340b2d7fcfd642231136185a Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Tue, 30 Jun 2015 14:12:42 +0100
-Subject: [PATCH] serial: 8250: Don't crash when nr_uarts is 0
-
----
- drivers/tty/serial/8250/8250_core.c | 2 ++
- 1 file changed, 2 insertions(+)
-
---- a/drivers/tty/serial/8250/8250_core.c
-+++ b/drivers/tty/serial/8250/8250_core.c
-@@ -509,6 +509,8 @@ static void __init serial8250_isa_init_p
-
- if (nr_uarts > UART_NR)
- nr_uarts = UART_NR;
-+ if (!nr_uarts)
-+ return;
-
- for (i = 0; i < nr_uarts; i++) {
- struct uart_8250_port *up = &serial8250_ports[i];
diff --git a/target/linux/brcm2708/patches-4.4/0009-pinctrl-bcm2835-Set-base-to-0-give-expected-gpio-num.patch b/target/linux/brcm2708/patches-4.4/0009-pinctrl-bcm2835-Set-base-to-0-give-expected-gpio-num.patch
deleted file mode 100644
index 3f70511..0000000
--- a/target/linux/brcm2708/patches-4.4/0009-pinctrl-bcm2835-Set-base-to-0-give-expected-gpio-num.patch
+++ /dev/null
@@ -1,21 +0,0 @@
-From 49cdca06e79b83f269961599d2c0b5bde9f12cfe Mon Sep 17 00:00:00 2001
-From: notro <notro at tronnes.org>
-Date: Thu, 10 Jul 2014 13:59:47 +0200
-Subject: [PATCH] pinctrl-bcm2835: Set base to 0 give expected gpio numbering
-
-Signed-off-by: Noralf Tronnes <notro at tronnes.org>
----
- drivers/pinctrl/bcm/pinctrl-bcm2835.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/pinctrl/bcm/pinctrl-bcm2835.c
-+++ b/drivers/pinctrl/bcm/pinctrl-bcm2835.c
-@@ -373,7 +373,7 @@ static struct gpio_chip bcm2835_gpio_chi
- .get = bcm2835_gpio_get,
- .set = bcm2835_gpio_set,
- .to_irq = bcm2835_gpio_to_irq,
-- .base = -1,
-+ .base = 0,
- .ngpio = BCM2835_NUM_GPIOS,
- .can_sleep = false,
- };
diff --git a/target/linux/brcm2708/patches-4.4/0010-pinctrl-bcm2835-Fix-interrupt-handling-for-GPIOs-28-.patch b/target/linux/brcm2708/patches-4.4/0010-pinctrl-bcm2835-Fix-interrupt-handling-for-GPIOs-28-.patch
deleted file mode 100644
index c9c3927..0000000
--- a/target/linux/brcm2708/patches-4.4/0010-pinctrl-bcm2835-Fix-interrupt-handling-for-GPIOs-28-.patch
+++ /dev/null
@@ -1,146 +0,0 @@
-From c51d537a465398bcbb03851a7f1c81b5324ee819 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Tue, 24 Feb 2015 13:40:50 +0000
-Subject: [PATCH] pinctrl-bcm2835: Fix interrupt handling for GPIOs 28-31 and
- 46-53
-
-Contrary to the documentation, the BCM2835 GPIO controller actually has
-four interrupt lines - one each for the three IRQ groups and one common. Rather
-confusingly, the GPIO interrupt groups don't correspond directly with the GPIO
-control banks. Instead, GPIOs 0-27 generate IRQ GPIO0, 28-45 GPIO1 and
-46-53 GPIO2.
-
-Awkwardly, the GPIOS for IRQ GPIO1 straddle two 32-entry GPIO banks, so it is
-cleaner to split out a function to process the interrupts for a single GPIO
-bank.
-
-This bug has only just been observed because GPIOs above 27 can only be
-accessed on an old Raspberry Pi with the optional P5 header fitted, where
-the pins are often used for I2S instead.
----
- drivers/pinctrl/bcm/pinctrl-bcm2835.c | 51 ++++++++++++++++++++++++++---------
- 1 file changed, 39 insertions(+), 12 deletions(-)
-
---- a/drivers/pinctrl/bcm/pinctrl-bcm2835.c
-+++ b/drivers/pinctrl/bcm/pinctrl-bcm2835.c
-@@ -47,6 +47,7 @@
- #define MODULE_NAME "pinctrl-bcm2835"
- #define BCM2835_NUM_GPIOS 54
- #define BCM2835_NUM_BANKS 2
-+#define BCM2835_NUM_IRQS 3
-
- #define BCM2835_PIN_BITMAP_SZ \
- DIV_ROUND_UP(BCM2835_NUM_GPIOS, sizeof(unsigned long) * 8)
-@@ -88,13 +89,13 @@ enum bcm2835_pinconf_pull {
-
- struct bcm2835_gpio_irqdata {
- struct bcm2835_pinctrl *pc;
-- int bank;
-+ int irqgroup;
- };
-
- struct bcm2835_pinctrl {
- struct device *dev;
- void __iomem *base;
-- int irq[BCM2835_NUM_BANKS];
-+ int irq[BCM2835_NUM_IRQS];
-
- /* note: locking assumes each bank will have its own unsigned long */
- unsigned long enabled_irq_map[BCM2835_NUM_BANKS];
-@@ -105,7 +106,7 @@ struct bcm2835_pinctrl {
- struct gpio_chip gpio_chip;
- struct pinctrl_gpio_range gpio_range;
-
-- struct bcm2835_gpio_irqdata irq_data[BCM2835_NUM_BANKS];
-+ struct bcm2835_gpio_irqdata irq_data[BCM2835_NUM_IRQS];
- spinlock_t irq_lock[BCM2835_NUM_BANKS];
- };
-
-@@ -378,17 +379,16 @@ static struct gpio_chip bcm2835_gpio_chi
- .can_sleep = false,
- };
-
--static irqreturn_t bcm2835_gpio_irq_handler(int irq, void *dev_id)
-+static int bcm2835_gpio_irq_handle_bank(struct bcm2835_pinctrl *pc,
-+ unsigned int bank, u32 mask)
- {
-- struct bcm2835_gpio_irqdata *irqdata = dev_id;
-- struct bcm2835_pinctrl *pc = irqdata->pc;
-- int bank = irqdata->bank;
- unsigned long events;
- unsigned offset;
- unsigned gpio;
- unsigned int type;
-
- events = bcm2835_gpio_rd(pc, GPEDS0 + bank * 4);
-+ events &= mask;
- events &= pc->enabled_irq_map[bank];
- for_each_set_bit(offset, &events, 32) {
- gpio = (32 * bank) + offset;
-@@ -396,7 +396,30 @@ static irqreturn_t bcm2835_gpio_irq_hand
-
- generic_handle_irq(irq_linear_revmap(pc->irq_domain, gpio));
- }
-- return events ? IRQ_HANDLED : IRQ_NONE;
-+
-+ return (events != 0);
-+}
-+
-+static irqreturn_t bcm2835_gpio_irq_handler(int irq, void *dev_id)
-+{
-+ struct bcm2835_gpio_irqdata *irqdata = dev_id;
-+ struct bcm2835_pinctrl *pc = irqdata->pc;
-+ int handled = 0;
-+
-+ switch (irqdata->irqgroup) {
-+ case 0: /* IRQ0 covers GPIOs 0-27 */
-+ handled = bcm2835_gpio_irq_handle_bank(pc, 0, 0x0fffffff);
-+ break;
-+ case 1: /* IRQ1 covers GPIOs 28-45 */
-+ handled = bcm2835_gpio_irq_handle_bank(pc, 0, 0xf0000000) |
-+ bcm2835_gpio_irq_handle_bank(pc, 1, 0x00003fff);
-+ break;
-+ case 2: /* IRQ2 covers GPIOs 46-53 */
-+ handled = bcm2835_gpio_irq_handle_bank(pc, 1, 0x003fc000);
-+ break;
-+ }
-+
-+ return handled ? IRQ_HANDLED : IRQ_NONE;
- }
-
- static inline void __bcm2835_gpio_irq_config(struct bcm2835_pinctrl *pc,
-@@ -985,8 +1008,6 @@ static int bcm2835_pinctrl_probe(struct
- for (i = 0; i < BCM2835_NUM_BANKS; i++) {
- unsigned long events;
- unsigned offset;
-- int len;
-- char *name;
-
- /* clear event detection flags */
- bcm2835_gpio_wr(pc, GPREN0 + i * 4, 0);
-@@ -1001,10 +1022,15 @@ static int bcm2835_pinctrl_probe(struct
- for_each_set_bit(offset, &events, 32)
- bcm2835_gpio_wr(pc, GPEDS0 + i * 4, BIT(offset));
-
-+ spin_lock_init(&pc->irq_lock[i]);
-+ }
-+
-+ for (i = 0; i < BCM2835_NUM_IRQS; i++) {
-+ int len;
-+ char *name;
- pc->irq[i] = irq_of_parse_and_map(np, i);
- pc->irq_data[i].pc = pc;
-- pc->irq_data[i].bank = i;
-- spin_lock_init(&pc->irq_lock[i]);
-+ pc->irq_data[i].irqgroup = i;
-
- len = strlen(dev_name(pc->dev)) + 16;
- name = devm_kzalloc(pc->dev, len, GFP_KERNEL);
-@@ -1062,6 +1088,7 @@ static struct platform_driver bcm2835_pi
- .remove = bcm2835_pinctrl_remove,
- .driver = {
- .name = MODULE_NAME,
-+ .owner = THIS_MODULE,
- .of_match_table = bcm2835_pinctrl_match,
- },
- };
diff --git a/target/linux/brcm2708/patches-4.4/0011-pinctrl-bcm2835-Only-request-the-interrupts-listed-i.patch b/target/linux/brcm2708/patches-4.4/0011-pinctrl-bcm2835-Only-request-the-interrupts-listed-i.patch
deleted file mode 100644
index 6fd945d..0000000
--- a/target/linux/brcm2708/patches-4.4/0011-pinctrl-bcm2835-Only-request-the-interrupts-listed-i.patch
+++ /dev/null
@@ -1,27 +0,0 @@
-From 49ffb4028436ce0efce2b8dede6138fc47b2cfd2 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Thu, 26 Feb 2015 09:58:22 +0000
-Subject: [PATCH] pinctrl-bcm2835: Only request the interrupts listed in the
- DTB
-
-Although the GPIO controller can generate three interrupts (four counting
-the common one), the device tree files currently only specify two. In the
-absence of the third, simply don't register that interrupt (as opposed to
-registering 0), which has the effect of making it impossible to generate
-interrupts for GPIOs 46-53 which, since they share pins with the SD card
-interface, is unlikely to be a problem.
----
- drivers/pinctrl/bcm/pinctrl-bcm2835.c | 2 ++
- 1 file changed, 2 insertions(+)
-
---- a/drivers/pinctrl/bcm/pinctrl-bcm2835.c
-+++ b/drivers/pinctrl/bcm/pinctrl-bcm2835.c
-@@ -1029,6 +1029,8 @@ static int bcm2835_pinctrl_probe(struct
- int len;
- char *name;
- pc->irq[i] = irq_of_parse_and_map(np, i);
-+ if (pc->irq[i] == 0)
-+ break;
- pc->irq_data[i].pc = pc;
- pc->irq_data[i].irqgroup = i;
-
diff --git a/target/linux/brcm2708/patches-4.4/0012-spi-bcm2835-Support-pin-groups-other-than-7-11.patch b/target/linux/brcm2708/patches-4.4/0012-spi-bcm2835-Support-pin-groups-other-than-7-11.patch
deleted file mode 100644
index 162a052..0000000
--- a/target/linux/brcm2708/patches-4.4/0012-spi-bcm2835-Support-pin-groups-other-than-7-11.patch
+++ /dev/null
@@ -1,80 +0,0 @@
-From 24fb0aecbadfc9bc8ebfb0c836ef7379b8fc5888 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Wed, 24 Jun 2015 14:10:44 +0100
-Subject: [PATCH] spi-bcm2835: Support pin groups other than 7-11
-
-The spi-bcm2835 driver automatically uses GPIO chip-selects due to
-some unreliability of the native ones. In doing so it chooses the
-same pins as the native chip-selects would use, but the existing
-code always uses pins 7 and 8, wherever the SPI function is mapped.
-
-Search the pinctrl group assigned to the driver for pins that
-correspond to native chip-selects, and use those for GPIO chip-
-selects.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- drivers/spi/spi-bcm2835.c | 45 +++++++++++++++++++++++++++++++++++++--------
- 1 file changed, 37 insertions(+), 8 deletions(-)
-
---- a/drivers/spi/spi-bcm2835.c
-+++ b/drivers/spi/spi-bcm2835.c
-@@ -688,6 +688,8 @@ static int bcm2835_spi_setup(struct spi_
- {
- int err;
- struct gpio_chip *chip;
-+ struct device_node *pins;
-+ u32 pingroup_index;
- /*
- * sanity checking the native-chipselects
- */
-@@ -704,15 +706,42 @@ static int bcm2835_spi_setup(struct spi_
- "setup: only two native chip-selects are supported\n");
- return -EINVAL;
- }
-- /* now translate native cs to GPIO */
-
-- /* get the gpio chip for the base */
-- chip = gpiochip_find("pinctrl-bcm2835", chip_match_name);
-- if (!chip)
-- return 0;
-+ /* now translate native cs to GPIO */
-+ /* first look for chip select pins in the devices pin groups */
-+ for (pingroup_index = 0;
-+ (pins = of_parse_phandle(spi->master->dev.of_node,
-+ "pinctrl-0",
-+ pingroup_index)) != 0;
-+ pingroup_index++) {
-+ u32 pin;
-+ u32 pin_index;
-+ for (pin_index = 0;
-+ of_property_read_u32_index(pins,
-+ "brcm,pins",
-+ pin_index,
-+ &pin) == 0;
-+ pin_index++) {
-+ if (((spi->chip_select == 0) &&
-+ ((pin == 8) || (pin == 36) || (pin == 46))) ||
-+ ((spi->chip_select == 1) &&
-+ ((pin == 7) || (pin == 35)))) {
-+ spi->cs_gpio = pin;
-+ break;
-+ }
-+ }
-+ of_node_put(pins);
-+ }
-+ /* if that fails, assume GPIOs 7-11 are used */
-+ if (!gpio_is_valid(spi->cs_gpio) ) {
-+ /* get the gpio chip for the base */
-+ chip = gpiochip_find("pinctrl-bcm2835", chip_match_name);
-+ if (!chip)
-+ return 0;
-
-- /* and calculate the real CS */
-- spi->cs_gpio = chip->base + 8 - spi->chip_select;
-+ /* and calculate the real CS */
-+ spi->cs_gpio = chip->base + 8 - spi->chip_select;
-+ }
-
- /* and set up the "mode" and level */
- dev_info(&spi->dev, "setting up native-CS%i as GPIO %i\n",
diff --git a/target/linux/brcm2708/patches-4.4/0013-ARM-bcm2835-Set-Serial-number-and-Revision.patch b/target/linux/brcm2708/patches-4.4/0013-ARM-bcm2835-Set-Serial-number-and-Revision.patch
deleted file mode 100644
index 9039731..0000000
--- a/target/linux/brcm2708/patches-4.4/0013-ARM-bcm2835-Set-Serial-number-and-Revision.patch
+++ /dev/null
@@ -1,58 +0,0 @@
-From 36aada743a4bdc21ad36c6b039449444a4b2ab22 Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Noralf=20Tr=C3=B8nnes?= <noralf at tronnes.org>
-Date: Wed, 3 Jun 2015 12:26:13 +0200
-Subject: [PATCH] ARM: bcm2835: Set Serial number and Revision
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-The VideoCore bootloader passes in Serial number and
-Revision number through Device Tree. Make these available to
-userspace through /proc/cpuinfo.
-
-Mainline status:
-
-There is a commit in linux-next that standardize passing the serial
-number through Device Tree (string: /serial-number):
-ARM: 8355/1: arch: Show the serial number from devicetree in cpuinfo
-
-There was an attempt to do the same with the revision number, but it
-didn't get in:
-[PATCH v2 1/2] arm: devtree: Set system_rev from DT revision
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
----
- arch/arm/mach-bcm/board_bcm2835.c | 9 +++++++++
- 1 file changed, 9 insertions(+)
-
---- a/arch/arm/mach-bcm/board_bcm2835.c
-+++ b/arch/arm/mach-bcm/board_bcm2835.c
-@@ -17,12 +17,16 @@
- #include <linux/of_address.h>
- #include <linux/of_platform.h>
- #include <linux/clk/bcm2835.h>
-+#include <asm/system_info.h>
-
- #include <asm/mach/arch.h>
- #include <asm/mach/map.h>
-
- static void __init bcm2835_init(void)
- {
-+ struct device_node *np = of_find_node_by_path("/system");
-+ u32 val;
-+ u64 val64;
- int ret;
-
- bcm2835_init_clocks();
-@@ -33,6 +37,11 @@ static void __init bcm2835_init(void)
- pr_err("of_platform_populate failed: %d\n", ret);
- BUG();
- }
-+
-+ if (!of_property_read_u32(np, "linux,revision", &val))
-+ system_rev = val;
-+ if (!of_property_read_u64(np, "linux,serial", &val64))
-+ system_serial_low = val64;
- }
-
- static const char * const bcm2835_compat[] = {
diff --git a/target/linux/brcm2708/patches-4.4/0014-bcm2835-i2s-get-base-address-for-DMA-from-devicetree.patch b/target/linux/brcm2708/patches-4.4/0014-bcm2835-i2s-get-base-address-for-DMA-from-devicetree.patch
deleted file mode 100644
index 9f869b5..0000000
--- a/target/linux/brcm2708/patches-4.4/0014-bcm2835-i2s-get-base-address-for-DMA-from-devicetree.patch
+++ /dev/null
@@ -1,65 +0,0 @@
-From fba1570f5f2fa5a65e933db49d3fc36126561a15 Mon Sep 17 00:00:00 2001
-From: Matthias Reichl <hias at horus.com>
-Date: Sun, 11 Oct 2015 16:44:05 +0200
-Subject: [PATCH] bcm2835-i2s: get base address for DMA from devicetree
-
-Code copied from spi-bcm2835. Get physical address from devicetree
-instead of using hardcoded constant.
-
-Signed-off-by: Matthias Reichl <hias at horus.com>
----
- sound/soc/bcm/bcm2835-i2s.c | 20 ++++++++++++--------
- 1 file changed, 12 insertions(+), 8 deletions(-)
-
---- a/sound/soc/bcm/bcm2835-i2s.c
-+++ b/sound/soc/bcm/bcm2835-i2s.c
-@@ -38,6 +38,7 @@
- #include <linux/delay.h>
- #include <linux/io.h>
- #include <linux/clk.h>
-+#include <linux/of_address.h>
-
- #include <sound/core.h>
- #include <sound/pcm.h>
-@@ -158,10 +159,6 @@ static const unsigned int bcm2835_clk_fr
- #define BCM2835_I2S_INT_RXR BIT(1)
- #define BCM2835_I2S_INT_TXW BIT(0)
-
--/* I2S DMA interface */
--/* FIXME: Needs IOMMU support */
--#define BCM2835_VCMMU_SHIFT (0x7E000000 - 0x20000000)
--
- /* General device struct */
- struct bcm2835_i2s_dev {
- struct device *dev;
-@@ -791,6 +788,15 @@ static int bcm2835_i2s_probe(struct plat
- int ret;
- struct regmap *regmap[2];
- struct resource *mem[2];
-+ const __be32 *addr;
-+ dma_addr_t dma_reg_base;
-+
-+ addr = of_get_address(pdev->dev.of_node, 0, NULL, NULL);
-+ if (!addr) {
-+ dev_err(&pdev->dev, "could not get DMA-register address\n");
-+ return -ENODEV;
-+ }
-+ dma_reg_base = be32_to_cpup(addr);
-
- /* Request both ioareas */
- for (i = 0; i <= 1; i++) {
-@@ -817,12 +823,10 @@ static int bcm2835_i2s_probe(struct plat
-
- /* Set the DMA address */
- dev->dma_data[SNDRV_PCM_STREAM_PLAYBACK].addr =
-- (dma_addr_t)mem[0]->start + BCM2835_I2S_FIFO_A_REG
-- + BCM2835_VCMMU_SHIFT;
-+ dma_reg_base + BCM2835_I2S_FIFO_A_REG;
-
- dev->dma_data[SNDRV_PCM_STREAM_CAPTURE].addr =
-- (dma_addr_t)mem[0]->start + BCM2835_I2S_FIFO_A_REG
-- + BCM2835_VCMMU_SHIFT;
-+ dma_reg_base + BCM2835_I2S_FIFO_A_REG;
-
- /* Set the bus width */
- dev->dma_data[SNDRV_PCM_STREAM_PLAYBACK].addr_width =
diff --git a/target/linux/brcm2708/patches-4.4/0015-bcm2835-i2s-add-24bit-support-update-bclk_ratio-to-m.patch b/target/linux/brcm2708/patches-4.4/0015-bcm2835-i2s-add-24bit-support-update-bclk_ratio-to-m.patch
deleted file mode 100644
index df806f4..0000000
--- a/target/linux/brcm2708/patches-4.4/0015-bcm2835-i2s-add-24bit-support-update-bclk_ratio-to-m.patch
+++ /dev/null
@@ -1,79 +0,0 @@
-From 002e593baa098b480ee0b6990ab3e43c6b36aac0 Mon Sep 17 00:00:00 2001
-From: Matthias Reichl <hias at horus.com>
-Date: Sun, 11 Oct 2015 15:21:16 +0200
-Subject: [PATCH] bcm2835-i2s: add 24bit support, update bclk_ratio to more
- correct values
-
-Code ported from bcm2708-i2s driver in Raspberry Pi tree.
-
-RPi commit 62c05a0b5328d9376d39c9e74da10b8a2465c234 ("ASoC: BCM2708:
-Add 24 bit support")
-
-This adds 24 bit support to the I2S driver of the BCM2708.
-Besides enabling the 24 bit flags, it includes two bug fixes:
-
-MMAP is not supported. Claiming this leads to strange issues
-when the format of driver and file do not match.
-
-The datasheet states that the width extension bit should be set
-for widths greater than 24, but greater or equal would be correct.
-This follows from the definition of the width field.
-
-Signed-off-by: Florian Meier <florian.meier at koalo.de>
-
-RPi commit 3e8c672bc4e92d457aa4654bbb4cfd79a18a2327 ("bcm2708-i2s:
-Update bclk_ratio to more correct values")
-
-Discussion about blck_ratio affecting sound quality:
-https://github.com/raspberrypi/linux/issues/681
-
-Signed-off-by: Matthias Reichl <hias at horus.com>
----
- sound/soc/bcm/bcm2835-i2s.c | 12 +++++++++---
- 1 file changed, 9 insertions(+), 3 deletions(-)
-
---- a/sound/soc/bcm/bcm2835-i2s.c
-+++ b/sound/soc/bcm/bcm2835-i2s.c
-@@ -340,11 +340,15 @@ static int bcm2835_i2s_hw_params(struct
- switch (params_format(params)) {
- case SNDRV_PCM_FORMAT_S16_LE:
- data_length = 16;
-- bclk_ratio = 40;
-+ bclk_ratio = 50;
-+ break;
-+ case SNDRV_PCM_FORMAT_S24_LE:
-+ data_length = 24;
-+ bclk_ratio = 50;
- break;
- case SNDRV_PCM_FORMAT_S32_LE:
- data_length = 32;
-- bclk_ratio = 80;
-+ bclk_ratio = 100;
- break;
- default:
- return -EINVAL;
-@@ -420,7 +424,7 @@ static int bcm2835_i2s_hw_params(struct
- /* Setup the frame format */
- format = BCM2835_I2S_CHEN;
-
-- if (data_length > 24)
-+ if (data_length >= 24)
- format |= BCM2835_I2S_CHWEX;
-
- format |= BCM2835_I2S_CHWID((data_length-8)&0xf);
-@@ -711,6 +715,7 @@ static struct snd_soc_dai_driver bcm2835
- .channels_max = 2,
- .rates = SNDRV_PCM_RATE_8000_192000,
- .formats = SNDRV_PCM_FMTBIT_S16_LE
-+ | SNDRV_PCM_FMTBIT_S24_LE
- | SNDRV_PCM_FMTBIT_S32_LE
- },
- .capture = {
-@@ -718,6 +723,7 @@ static struct snd_soc_dai_driver bcm2835
- .channels_max = 2,
- .rates = SNDRV_PCM_RATE_8000_192000,
- .formats = SNDRV_PCM_FMTBIT_S16_LE
-+ | SNDRV_PCM_FMTBIT_S24_LE
- | SNDRV_PCM_FMTBIT_S32_LE
- },
- .ops = &bcm2835_i2s_dai_ops,
diff --git a/target/linux/brcm2708/patches-4.4/0016-bcm2835-i2s-setup-clock-only-if-CPU-is-clock-master.patch b/target/linux/brcm2708/patches-4.4/0016-bcm2835-i2s-setup-clock-only-if-CPU-is-clock-master.patch
deleted file mode 100644
index 995266a..0000000
--- a/target/linux/brcm2708/patches-4.4/0016-bcm2835-i2s-setup-clock-only-if-CPU-is-clock-master.patch
+++ /dev/null
@@ -1,54 +0,0 @@
-From 2165ae346e98922f21ffe6abad1f6d4226e445b1 Mon Sep 17 00:00:00 2001
-From: Matthias Reichl <hias at horus.com>
-Date: Sun, 11 Oct 2015 15:25:51 +0200
-Subject: [PATCH] bcm2835-i2s: setup clock only if CPU is clock master
-
-Code ported from bcm2708-i2s driver in Raspberry Pi tree.
-
-RPi commit c14827ecdaa36607f6110f9ce8df96e698672191 ("bcm2708: Allow
-option card devices to be configured via DT")
-
-Original work by Zoltan Szenczi, committed to RPi tree by
-Phil Elwell.
-
-Signed-off-by: Matthias Reichl <hias at horus.com>
----
- sound/soc/bcm/bcm2835-i2s.c | 28 +++++++++++++++++++---------
- 1 file changed, 19 insertions(+), 9 deletions(-)
-
---- a/sound/soc/bcm/bcm2835-i2s.c
-+++ b/sound/soc/bcm/bcm2835-i2s.c
-@@ -411,15 +411,25 @@ static int bcm2835_i2s_hw_params(struct
- divf = dividend & BCM2835_CLK_DIVF_MASK;
- }
-
-- /* Set clock divider */
-- regmap_write(dev->clk_regmap, BCM2835_CLK_PCMDIV_REG, BCM2835_CLK_PASSWD
-- | BCM2835_CLK_DIVI(divi)
-- | BCM2835_CLK_DIVF(divf));
-+ /* Clock should only be set up here if CPU is clock master */
-+ switch (dev->fmt & SND_SOC_DAIFMT_MASTER_MASK) {
-+ case SND_SOC_DAIFMT_CBS_CFS:
-+ case SND_SOC_DAIFMT_CBS_CFM:
-+ /* Set clock divider */
-+ regmap_write(dev->clk_regmap, BCM2835_CLK_PCMDIV_REG,
-+ BCM2835_CLK_PASSWD
-+ | BCM2835_CLK_DIVI(divi)
-+ | BCM2835_CLK_DIVF(divf));
-
-- /* Setup clock, but don't start it yet */
-- regmap_write(dev->clk_regmap, BCM2835_CLK_PCMCTL_REG, BCM2835_CLK_PASSWD
-- | BCM2835_CLK_MASH(mash)
-- | BCM2835_CLK_SRC(clk_src));
-+ /* Setup clock, but don't start it yet */
-+ regmap_write(dev->clk_regmap, BCM2835_CLK_PCMCTL_REG,
-+ BCM2835_CLK_PASSWD
-+ | BCM2835_CLK_MASH(mash)
-+ | BCM2835_CLK_SRC(clk_src));
-+ break;
-+ default:
-+ break;
-+ }
-
- /* Setup the frame format */
- format = BCM2835_I2S_CHEN;
diff --git a/target/linux/brcm2708/patches-4.4/0017-bcm2835-i2s-Eliminate-debugfs-directory-error.patch b/target/linux/brcm2708/patches-4.4/0017-bcm2835-i2s-Eliminate-debugfs-directory-error.patch
deleted file mode 100644
index 7d58d36..0000000
--- a/target/linux/brcm2708/patches-4.4/0017-bcm2835-i2s-Eliminate-debugfs-directory-error.patch
+++ /dev/null
@@ -1,36 +0,0 @@
-From 186eb5323a8492382d30e4857a0e45c8fc80ff2d Mon Sep 17 00:00:00 2001
-From: Matthias Reichl <hias at horus.com>
-Date: Sun, 11 Oct 2015 15:49:51 +0200
-Subject: [PATCH] bcm2835-i2s: Eliminate debugfs directory error
-
-Code ported from bcm2708-i2s driver in Raspberry Pi tree.
-
-RPi commit fd7d7a3dbe9262d16971ef81c234ed28c6499dd7 ("bcm2708:
-Eliminate i2s debugfs directory error")
-
-Qualify the two regmap ranges uses by bcm2708-i2s ('-i2s' and '-clk')
-to avoid the name clash when registering debugfs entries.
-
-Signed-off-by: Matthias Reichl <hias at horus.com>
----
- sound/soc/bcm/bcm2835-i2s.c | 2 ++
- 1 file changed, 2 insertions(+)
-
---- a/sound/soc/bcm/bcm2835-i2s.c
-+++ b/sound/soc/bcm/bcm2835-i2s.c
-@@ -782,6 +782,7 @@ static const struct regmap_config bcm283
- .precious_reg = bcm2835_i2s_precious_reg,
- .volatile_reg = bcm2835_i2s_volatile_reg,
- .cache_type = REGCACHE_RBTREE,
-+ .name = "i2s",
- },
- {
- .reg_bits = 32,
-@@ -790,6 +791,7 @@ static const struct regmap_config bcm283
- .max_register = BCM2835_CLK_PCMDIV_REG,
- .volatile_reg = bcm2835_clk_volatile_reg,
- .cache_type = REGCACHE_RBTREE,
-+ .name = "clk",
- },
- };
-
diff --git a/target/linux/brcm2708/patches-4.4/0018-bcm2835-i2s-Register-PCM-device.patch b/target/linux/brcm2708/patches-4.4/0018-bcm2835-i2s-Register-PCM-device.patch
deleted file mode 100644
index 1c60a01..0000000
--- a/target/linux/brcm2708/patches-4.4/0018-bcm2835-i2s-Register-PCM-device.patch
+++ /dev/null
@@ -1,63 +0,0 @@
-From 1c6fdc37e81dcd4be3590c7130320f23ad0761df Mon Sep 17 00:00:00 2001
-From: Matthias Reichl <hias at horus.com>
-Date: Sun, 11 Oct 2015 15:35:20 +0200
-Subject: [PATCH] bcm2835-i2s: Register PCM device
-
-Code ported from bcm2708-i2s driver in Raspberry Pi tree.
-
-RPi commit ba46b4935a23aa2caac1855ead52a035d4776680 ("ASoC: Add
-support for BCM2708")
-
-This driver adds support for digital audio (I2S)
-for the BCM2708 SoC that is used by the
-Raspberry Pi. External audio codecs can be
-connected to the Raspberry Pi via P5 header.
-
-It relies on cyclic DMA engine support for BCM2708.
-
-Signed-off-by: Florian Meier <florian.meier at koalo.de>
-
-Signed-off-by: Matthias Reichl <hias at horus.com>
----
- sound/soc/bcm/bcm2835-i2s.c | 23 ++++++++++++++++++++++-
- 1 file changed, 22 insertions(+), 1 deletion(-)
-
---- a/sound/soc/bcm/bcm2835-i2s.c
-+++ b/sound/soc/bcm/bcm2835-i2s.c
-@@ -799,6 +799,25 @@ static const struct snd_soc_component_dr
- .name = "bcm2835-i2s-comp",
- };
-
-+static const struct snd_pcm_hardware bcm2835_pcm_hardware = {
-+ .info = SNDRV_PCM_INFO_INTERLEAVED |
-+ SNDRV_PCM_INFO_JOINT_DUPLEX,
-+ .formats = SNDRV_PCM_FMTBIT_S16_LE |
-+ SNDRV_PCM_FMTBIT_S24_LE |
-+ SNDRV_PCM_FMTBIT_S32_LE,
-+ .period_bytes_min = 32,
-+ .period_bytes_max = 64 * PAGE_SIZE,
-+ .periods_min = 2,
-+ .periods_max = 255,
-+ .buffer_bytes_max = 128 * PAGE_SIZE,
-+};
-+
-+static const struct snd_dmaengine_pcm_config bcm2835_dmaengine_pcm_config = {
-+ .prepare_slave_config = snd_dmaengine_pcm_prepare_slave_config,
-+ .pcm_hardware = &bcm2835_pcm_hardware,
-+ .prealloc_buffer_size = 256 * PAGE_SIZE,
-+};
-+
- static int bcm2835_i2s_probe(struct platform_device *pdev)
- {
- struct bcm2835_i2s_dev *dev;
-@@ -870,7 +889,9 @@ static int bcm2835_i2s_probe(struct plat
- return ret;
- }
-
-- ret = devm_snd_dmaengine_pcm_register(&pdev->dev, NULL, 0);
-+ ret = devm_snd_dmaengine_pcm_register(&pdev->dev,
-+ &bcm2835_dmaengine_pcm_config,
-+ SND_DMAENGINE_PCM_FLAG_COMPAT);
- if (ret) {
- dev_err(&pdev->dev, "Could not register PCM: %d\n", ret);
- return ret;
diff --git a/target/linux/brcm2708/patches-4.4/0019-bcm2835-i2s-Enable-MMAP-support-via-a-DT-property.patch b/target/linux/brcm2708/patches-4.4/0019-bcm2835-i2s-Enable-MMAP-support-via-a-DT-property.patch
deleted file mode 100644
index ca9c521..0000000
--- a/target/linux/brcm2708/patches-4.4/0019-bcm2835-i2s-Enable-MMAP-support-via-a-DT-property.patch
+++ /dev/null
@@ -1,44 +0,0 @@
-From 8d32cc49fa07fb95dd101b2d544ed02027982cab Mon Sep 17 00:00:00 2001
-From: Matthias Reichl <hias at horus.com>
-Date: Sun, 11 Oct 2015 15:55:21 +0200
-Subject: [PATCH] bcm2835-i2s: Enable MMAP support via a DT property
-
-Code ported from bcm2708-i2s driver in Raspberry Pi tree.
-
-RPi commit 7ee829fd77a30127db5d0b3c7d79b8718166e568 ("bcm2708-i2s:
-Enable MMAP support via a DT property and overlay")
-
-The i2s driver used to claim to support MMAP, but that feature was disabled
-when some problems were found. Add the ability to enable this feature
-through Device Tree, using the i2s-mmap overlay.
-
-See: #1004
-
-Signed-off-by: Matthias Reichl <hias at horus.com>
----
- sound/soc/bcm/bcm2835-i2s.c | 7 ++++++-
- 1 file changed, 6 insertions(+), 1 deletion(-)
-
---- a/sound/soc/bcm/bcm2835-i2s.c
-+++ b/sound/soc/bcm/bcm2835-i2s.c
-@@ -799,7 +799,7 @@ static const struct snd_soc_component_dr
- .name = "bcm2835-i2s-comp",
- };
-
--static const struct snd_pcm_hardware bcm2835_pcm_hardware = {
-+static struct snd_pcm_hardware bcm2835_pcm_hardware = {
- .info = SNDRV_PCM_INFO_INTERLEAVED |
- SNDRV_PCM_INFO_JOINT_DUPLEX,
- .formats = SNDRV_PCM_FMTBIT_S16_LE |
-@@ -835,6 +835,11 @@ static int bcm2835_i2s_probe(struct plat
- }
- dma_reg_base = be32_to_cpup(addr);
-
-+ if (of_property_read_bool(pdev->dev.of_node, "brcm,enable-mmap"))
-+ bcm2835_pcm_hardware.info |=
-+ SNDRV_PCM_INFO_MMAP |
-+ SNDRV_PCM_INFO_MMAP_VALID;
-+
- /* Request both ioareas */
- for (i = 0; i <= 1; i++) {
- void __iomem *base;
diff --git a/target/linux/brcm2708/patches-4.4/0020-dmaengine-bcm2835-Add-slave-dma-support.patch b/target/linux/brcm2708/patches-4.4/0020-dmaengine-bcm2835-Add-slave-dma-support.patch
deleted file mode 100644
index a8530bf..0000000
--- a/target/linux/brcm2708/patches-4.4/0020-dmaengine-bcm2835-Add-slave-dma-support.patch
+++ /dev/null
@@ -1,320 +0,0 @@
-From 46870419f14aa3631e1269f3ac452c99b0f1a505 Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Noralf=20Tr=C3=B8nnes?= <noralf at tronnes.org>
-Date: Thu, 9 Apr 2015 12:34:11 +0200
-Subject: [PATCH] dmaengine: bcm2835: Add slave dma support
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Add slave transfer capability to BCM2835 dmaengine driver.
-This patch is pulled from the bcm2708-dmaengine driver in the
-Raspberry Pi repo. The work was done by Gellert Weisz.
-
-Tested using the bcm2835-mmc driver from the same repo.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
----
- drivers/dma/bcm2835-dma.c | 206 ++++++++++++++++++++++++++++++++++++++++++----
- 1 file changed, 192 insertions(+), 14 deletions(-)
-
---- a/drivers/dma/bcm2835-dma.c
-+++ b/drivers/dma/bcm2835-dma.c
-@@ -1,11 +1,10 @@
- /*
- * BCM2835 DMA engine support
- *
-- * This driver only supports cyclic DMA transfers
-- * as needed for the I2S module.
-- *
- * Author: Florian Meier <florian.meier at koalo.de>
- * Copyright 2013
-+ * Gellert Weisz <gellert at raspberrypi.org>
-+ * Copyright 2013-2014
- *
- * Based on
- * OMAP DMAengine support by Russell King
-@@ -95,6 +94,8 @@ struct bcm2835_desc {
- size_t size;
- };
-
-+#define BCM2835_DMA_WAIT_CYCLES 0 /* Slow down DMA transfers: 0-31 */
-+
- #define BCM2835_DMA_CS 0x00
- #define BCM2835_DMA_ADDR 0x04
- #define BCM2835_DMA_SOURCE_AD 0x0c
-@@ -111,12 +112,16 @@ struct bcm2835_desc {
- #define BCM2835_DMA_RESET BIT(31) /* WO, self clearing */
-
- #define BCM2835_DMA_INT_EN BIT(0)
-+#define BCM2835_DMA_WAIT_RESP BIT(3)
- #define BCM2835_DMA_D_INC BIT(4)
-+#define BCM2835_DMA_D_WIDTH BIT(5)
- #define BCM2835_DMA_D_DREQ BIT(6)
- #define BCM2835_DMA_S_INC BIT(8)
-+#define BCM2835_DMA_S_WIDTH BIT(9)
- #define BCM2835_DMA_S_DREQ BIT(10)
-
- #define BCM2835_DMA_PER_MAP(x) ((x) << 16)
-+#define BCM2835_DMA_WAITS(x) (((x) & 0x1f) << 21)
-
- #define BCM2835_DMA_DATA_TYPE_S8 1
- #define BCM2835_DMA_DATA_TYPE_S16 2
-@@ -130,6 +135,14 @@ struct bcm2835_desc {
- #define BCM2835_DMA_CHAN(n) ((n) << 8) /* Base address */
- #define BCM2835_DMA_CHANIO(base, n) ((base) + BCM2835_DMA_CHAN(n))
-
-+#define MAX_NORMAL_TRANSFER SZ_1G
-+/*
-+ * Max length on a Lite channel is 65535 bytes.
-+ * DMA handles byte-enables on SDRAM reads and writes even on 128-bit accesses,
-+ * but byte-enables don't exist on peripheral addresses, so align to 32-bit.
-+ */
-+#define MAX_LITE_TRANSFER (SZ_64K - 4)
-+
- static inline struct bcm2835_dmadev *to_bcm2835_dma_dev(struct dma_device *d)
- {
- return container_of(d, struct bcm2835_dmadev, ddev);
-@@ -226,12 +239,18 @@ static irqreturn_t bcm2835_dma_callback(
- d = c->desc;
-
- if (d) {
-- /* TODO Only works for cyclic DMA */
-- vchan_cyclic_callback(&d->vd);
-- }
-+ if (c->cyclic) {
-+ vchan_cyclic_callback(&d->vd);
-
-- /* Keep the DMA engine running */
-- writel(BCM2835_DMA_ACTIVE, c->chan_base + BCM2835_DMA_CS);
-+ /* Keep the DMA engine running */
-+ writel(BCM2835_DMA_ACTIVE,
-+ c->chan_base + BCM2835_DMA_CS);
-+
-+ } else {
-+ vchan_cookie_complete(&c->desc->vd);
-+ bcm2835_dma_start_desc(c);
-+ }
-+ }
-
- spin_unlock_irqrestore(&c->vc.lock, flags);
-
-@@ -339,8 +358,6 @@ static void bcm2835_dma_issue_pending(st
- struct bcm2835_chan *c = to_bcm2835_dma_chan(chan);
- unsigned long flags;
-
-- c->cyclic = true; /* Nothing else is implemented */
--
- spin_lock_irqsave(&c->vc.lock, flags);
- if (vchan_issue_pending(&c->vc) && !c->desc)
- bcm2835_dma_start_desc(c);
-@@ -358,7 +375,7 @@ static struct dma_async_tx_descriptor *b
- struct bcm2835_desc *d;
- dma_addr_t dev_addr;
- unsigned int es, sync_type;
-- unsigned int frame;
-+ unsigned int frame, max_size;
- int i;
-
- /* Grab configuration */
-@@ -393,7 +410,12 @@ static struct dma_async_tx_descriptor *b
-
- d->c = c;
- d->dir = direction;
-- d->frames = buf_len / period_len;
-+ if (c->ch >= 8) /* LITE channel */
-+ max_size = MAX_LITE_TRANSFER;
-+ else
-+ max_size = MAX_NORMAL_TRANSFER;
-+ period_len = min(period_len, max_size);
-+ d->frames = (buf_len - 1) / (period_len + 1);
-
- d->cb_list = kcalloc(d->frames, sizeof(*d->cb_list), GFP_KERNEL);
- if (!d->cb_list) {
-@@ -441,17 +463,171 @@ static struct dma_async_tx_descriptor *b
- BCM2835_DMA_PER_MAP(c->dreq);
-
- /* Length of a frame */
-- control_block->length = period_len;
-+ if (frame != d->frames - 1)
-+ control_block->length = period_len;
-+ else
-+ control_block->length = buf_len - (d->frames - 1) *
-+ period_len;
- d->size += control_block->length;
-
- /*
- * Next block is the next frame.
-- * This DMA engine driver currently only supports cyclic DMA.
-+ * This function is called on cyclic DMA transfers.
- * Therefore, wrap around at number of frames.
- */
- control_block->next = d->cb_list[((frame + 1) % d->frames)].paddr;
- }
-
-+ c->cyclic = true;
-+
-+ return vchan_tx_prep(&c->vc, &d->vd, flags);
-+}
-+
-+static struct dma_async_tx_descriptor *
-+bcm2835_dma_prep_slave_sg(struct dma_chan *chan,
-+ struct scatterlist *sgl,
-+ unsigned int sg_len,
-+ enum dma_transfer_direction direction,
-+ unsigned long flags, void *context)
-+{
-+ struct bcm2835_chan *c = to_bcm2835_dma_chan(chan);
-+ enum dma_slave_buswidth dev_width;
-+ struct bcm2835_desc *d;
-+ dma_addr_t dev_addr;
-+ struct scatterlist *sgent;
-+ unsigned int i, sync_type, split_cnt, max_size;
-+
-+ if (!is_slave_direction(direction)) {
-+ dev_err(chan->device->dev, "direction not supported\n");
-+ return NULL;
-+ }
-+
-+ if (direction == DMA_DEV_TO_MEM) {
-+ dev_addr = c->cfg.src_addr;
-+ dev_width = c->cfg.src_addr_width;
-+ sync_type = BCM2835_DMA_S_DREQ;
-+ } else {
-+ dev_addr = c->cfg.dst_addr;
-+ dev_width = c->cfg.dst_addr_width;
-+ sync_type = BCM2835_DMA_D_DREQ;
-+ }
-+
-+ /* Bus width translates to the element size (ES) */
-+ switch (dev_width) {
-+ case DMA_SLAVE_BUSWIDTH_4_BYTES:
-+ break;
-+ default:
-+ dev_err(chan->device->dev, "buswidth not supported: %i\n",
-+ dev_width);
-+ return NULL;
-+ }
-+
-+ /* Allocate and setup the descriptor. */
-+ d = kzalloc(sizeof(*d), GFP_NOWAIT);
-+ if (!d)
-+ return NULL;
-+
-+ d->dir = direction;
-+
-+ if (c->ch >= 8) /* LITE channel */
-+ max_size = MAX_LITE_TRANSFER;
-+ else
-+ max_size = MAX_NORMAL_TRANSFER;
-+
-+ /*
-+ * Store the length of the SG list in d->frames
-+ * taking care to account for splitting up transfers
-+ * too large for a LITE channel
-+ */
-+ d->frames = 0;
-+ for_each_sg(sgl, sgent, sg_len, i) {
-+ unsigned int len = sg_dma_len(sgent);
-+
-+ d->frames += len / max_size + 1;
-+ }
-+
-+ /* Allocate memory for control blocks */
-+ d->control_block_size = d->frames * sizeof(struct bcm2835_dma_cb);
-+ d->control_block_base = dma_zalloc_coherent(chan->device->dev,
-+ d->control_block_size, &d->control_block_base_phys,
-+ GFP_NOWAIT);
-+ if (!d->control_block_base) {
-+ kfree(d);
-+ return NULL;
-+ }
-+
-+ /*
-+ * Iterate over all SG entries, create a control block
-+ * for each frame and link them together.
-+ * Count the number of times an SG entry had to be split
-+ * as a result of using a LITE channel
-+ */
-+ split_cnt = 0;
-+
-+ for_each_sg(sgl, sgent, sg_len, i) {
-+ unsigned int j;
-+ dma_addr_t addr = sg_dma_address(sgent);
-+ unsigned int len = sg_dma_len(sgent);
-+
-+ for (j = 0; j < len; j += max_size) {
-+ struct bcm2835_dma_cb *control_block =
-+ &d->control_block_base[i + split_cnt];
-+
-+ /* Setup addresses */
-+ if (d->dir == DMA_DEV_TO_MEM) {
-+ control_block->info = BCM2835_DMA_D_INC |
-+ BCM2835_DMA_D_WIDTH |
-+ BCM2835_DMA_S_DREQ;
-+ control_block->src = dev_addr;
-+ control_block->dst = addr + (dma_addr_t)j;
-+ } else {
-+ control_block->info = BCM2835_DMA_S_INC |
-+ BCM2835_DMA_S_WIDTH |
-+ BCM2835_DMA_D_DREQ;
-+ control_block->src = addr + (dma_addr_t)j;
-+ control_block->dst = dev_addr;
-+ }
-+
-+ /* Common part */
-+ control_block->info |=
-+ BCM2835_DMA_WAITS(BCM2835_DMA_WAIT_CYCLES);
-+ control_block->info |= BCM2835_DMA_WAIT_RESP;
-+
-+ /* Enable */
-+ if (i == sg_len - 1 && len - j <= max_size)
-+ control_block->info |= BCM2835_DMA_INT_EN;
-+
-+ /* Setup synchronization */
-+ if (sync_type)
-+ control_block->info |= sync_type;
-+
-+ /* Setup DREQ channel */
-+ if (c->dreq)
-+ control_block->info |=
-+ BCM2835_DMA_PER_MAP(c->dreq);
-+
-+ /* Length of a frame */
-+ control_block->length = min(len - j, max_size);
-+ d->size += control_block->length;
-+
-+ if (i < sg_len - 1 || len - j > max_size) {
-+ /* Next block is the next frame. */
-+ control_block->next =
-+ d->control_block_base_phys +
-+ sizeof(struct bcm2835_dma_cb) *
-+ (i + split_cnt + 1);
-+ } else {
-+ /* Next block is empty. */
-+ control_block->next = 0;
-+ }
-+
-+ if (len - j > max_size)
-+ split_cnt++;
-+ }
-+ }
-+
-+ c->cyclic = false;
-+
- return vchan_tx_prep(&c->vc, &d->vd, flags);
- error_cb:
- i--;
-@@ -620,6 +796,7 @@ static int bcm2835_dma_probe(struct plat
- od->ddev.device_tx_status = bcm2835_dma_tx_status;
- od->ddev.device_issue_pending = bcm2835_dma_issue_pending;
- od->ddev.device_prep_dma_cyclic = bcm2835_dma_prep_dma_cyclic;
-+ od->ddev.device_prep_slave_sg = bcm2835_dma_prep_slave_sg;
- od->ddev.device_config = bcm2835_dma_slave_config;
- od->ddev.device_terminate_all = bcm2835_dma_terminate_all;
- od->ddev.src_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_4_BYTES);
-@@ -708,4 +885,5 @@ module_platform_driver(bcm2835_dma_drive
- MODULE_ALIAS("platform:bcm2835-dma");
- MODULE_DESCRIPTION("BCM2835 DMA engine driver");
- MODULE_AUTHOR("Florian Meier <florian.meier at koalo.de>");
-+MODULE_AUTHOR("Gellert Weisz <gellert at raspberrypi.org>");
- MODULE_LICENSE("GPL v2");
diff --git a/target/linux/brcm2708/patches-4.4/0021-dmaengine-bcm2835-set-residue_granularity-field.patch b/target/linux/brcm2708/patches-4.4/0021-dmaengine-bcm2835-set-residue_granularity-field.patch
deleted file mode 100644
index f1384c2..0000000
--- a/target/linux/brcm2708/patches-4.4/0021-dmaengine-bcm2835-set-residue_granularity-field.patch
+++ /dev/null
@@ -1,29 +0,0 @@
-From cdc0392f43a1ef5571880aefeefd1ffbefd1a726 Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Noralf=20Tr=C3=B8nnes?= <noralf at tronnes.org>
-Date: Sat, 3 Oct 2015 15:58:59 +0200
-Subject: [PATCH] dmaengine: bcm2835: set residue_granularity field
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-bcm2835-dma supports residue reporting at burst level but didn't report
-this via the residue_granularity field.
-
-Without this field set properly we get playback issues with I2S cards.
-
-[by HiassofT, taken from bcm2708-dmaengine]
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
----
- drivers/dma/bcm2835-dma.c | 1 +
- 1 file changed, 1 insertion(+)
-
---- a/drivers/dma/bcm2835-dma.c
-+++ b/drivers/dma/bcm2835-dma.c
-@@ -802,6 +802,7 @@ static int bcm2835_dma_probe(struct plat
- od->ddev.src_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_4_BYTES);
- od->ddev.dst_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_4_BYTES);
- od->ddev.directions = BIT(DMA_DEV_TO_MEM) | BIT(DMA_MEM_TO_DEV);
-+ od->ddev.residue_granularity = DMA_RESIDUE_GRANULARITY_BURST;
- od->ddev.dev = &pdev->dev;
- INIT_LIST_HEAD(&od->ddev.channels);
- spin_lock_init(&od->lock);
diff --git a/target/linux/brcm2708/patches-4.4/0022-dmaengine-bcm2835-Load-driver-early-and-support-lega.patch b/target/linux/brcm2708/patches-4.4/0022-dmaengine-bcm2835-Load-driver-early-and-support-lega.patch
deleted file mode 100644
index bec3a30..0000000
--- a/target/linux/brcm2708/patches-4.4/0022-dmaengine-bcm2835-Load-driver-early-and-support-lega.patch
+++ /dev/null
@@ -1,97 +0,0 @@
-From 50e1ac1b9abaacc14f45e7ca73dc613c4d6dba99 Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Noralf=20Tr=C3=B8nnes?= <noralf at tronnes.org>
-Date: Sat, 3 Oct 2015 22:22:55 +0200
-Subject: [PATCH] dmaengine: bcm2835: Load driver early and support legacy API
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Load driver early since at least bcm2708_fb doesn't support deferred
-probing and even if it did, we don't want the video driver deferred.
-Support the legacy DMA API which is needed by bcm2708_fb.
-Don't mask out channel 2.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
----
- drivers/dma/Kconfig | 2 +-
- drivers/dma/bcm2835-dma.c | 30 ++++++++++++++++++++++++------
- 2 files changed, 25 insertions(+), 7 deletions(-)
-
---- a/drivers/dma/Kconfig
-+++ b/drivers/dma/Kconfig
-@@ -108,7 +108,7 @@ config COH901318
-
- config DMA_BCM2835
- tristate "BCM2835 DMA engine support"
-- depends on ARCH_BCM2835
-+ depends on ARCH_BCM2835 || ARCH_BCM2708 || ARCH_BCM2709
- select DMA_ENGINE
- select DMA_VIRTUAL_CHANNELS
-
---- a/drivers/dma/bcm2835-dma.c
-+++ b/drivers/dma/bcm2835-dma.c
-@@ -36,6 +36,7 @@
- #include <linux/interrupt.h>
- #include <linux/list.h>
- #include <linux/module.h>
-+#include <linux/platform_data/dma-bcm2708.h>
- #include <linux/platform_device.h>
- #include <linux/slab.h>
- #include <linux/io.h>
-@@ -786,6 +787,10 @@ static int bcm2835_dma_probe(struct plat
- if (IS_ERR(base))
- return PTR_ERR(base);
-
-+ rc = bcm_dmaman_probe(pdev, base, BCM2835_DMA_BULK_MASK);
-+ if (rc)
-+ dev_err(&pdev->dev, "Failed to initialize the legacy API\n");
-+
- od->base = base;
-
- dma_cap_set(DMA_SLAVE, od->ddev.cap_mask);
-@@ -818,11 +823,8 @@ static int bcm2835_dma_probe(struct plat
- goto err_no_dma;
- }
-
-- /*
-- * Do not use the FIQ and BULK channels,
-- * because they are used by the GPU.
-- */
-- chans_available &= ~(BCM2835_DMA_FIQ_MASK | BCM2835_DMA_BULK_MASK);
-+ /* Channel 0 is used by the legacy API */
-+ chans_available &= ~BCM2835_DMA_BULK_MASK;
-
- for (i = 0; i < pdev->num_resources; i++) {
- irq = platform_get_irq(pdev, i);
-@@ -866,6 +868,7 @@ static int bcm2835_dma_remove(struct pla
- {
- struct bcm2835_dmadev *od = platform_get_drvdata(pdev);
-
-+ bcm_dmaman_remove(pdev);
- dma_async_device_unregister(&od->ddev);
- bcm2835_dma_free(od);
-
-@@ -881,7 +884,22 @@ static struct platform_driver bcm2835_dm
- },
- };
-
--module_platform_driver(bcm2835_dma_driver);
-+static int bcm2835_dma_init(void)
-+{
-+ return platform_driver_register(&bcm2835_dma_driver);
-+}
-+
-+static void bcm2835_dma_exit(void)
-+{
-+ platform_driver_unregister(&bcm2835_dma_driver);
-+}
-+
-+/*
-+ * Load after serial driver (arch_initcall) so we see the messages if it fails,
-+ * but before drivers (module_init) that need a DMA channel.
-+ */
-+subsys_initcall(bcm2835_dma_init);
-+module_exit(bcm2835_dma_exit);
-
- MODULE_ALIAS("platform:bcm2835-dma");
- MODULE_DESCRIPTION("BCM2835 DMA engine driver");
diff --git a/target/linux/brcm2708/patches-4.4/0023-bcm2835-dma-Fix-dreq-not-set-for-slave-transfers.patch b/target/linux/brcm2708/patches-4.4/0023-bcm2835-dma-Fix-dreq-not-set-for-slave-transfers.patch
deleted file mode 100644
index 070afe0..0000000
--- a/target/linux/brcm2708/patches-4.4/0023-bcm2835-dma-Fix-dreq-not-set-for-slave-transfers.patch
+++ /dev/null
@@ -1,21 +0,0 @@
-From 1dd1e763873c2e19ec9cfc8134b91406c36cac30 Mon Sep 17 00:00:00 2001
-From: Matthias Reichl <hias at horus.com>
-Date: Sat, 10 Oct 2015 12:29:18 +0200
-Subject: [PATCH] bcm2835-dma: Fix dreq not set for slave transfers
-
-Set dreq to slave_id if it is not set like in bcm2708-dmaengine.
----
- drivers/dma/bcm2835-dma.c | 2 ++
- 1 file changed, 2 insertions(+)
-
---- a/drivers/dma/bcm2835-dma.c
-+++ b/drivers/dma/bcm2835-dma.c
-@@ -657,6 +657,8 @@ static int bcm2835_dma_slave_config(stru
- }
-
- c->cfg = *cfg;
-+ if (!c->dreq)
-+ c->dreq = cfg->slave_id;
-
- return 0;
- }
diff --git a/target/linux/brcm2708/patches-4.4/0024-bcm2835-dma-Limit-cyclic-transfers-on-lite-channels-.patch b/target/linux/brcm2708/patches-4.4/0024-bcm2835-dma-Limit-cyclic-transfers-on-lite-channels-.patch
deleted file mode 100644
index 1e26670..0000000
--- a/target/linux/brcm2708/patches-4.4/0024-bcm2835-dma-Limit-cyclic-transfers-on-lite-channels-.patch
+++ /dev/null
@@ -1,36 +0,0 @@
-From f0f4368b3497d129c0c4ca0565f5b6656faed474 Mon Sep 17 00:00:00 2001
-From: Matthias Reichl <hias at horus.com>
-Date: Sun, 11 Oct 2015 12:28:30 +0200
-Subject: [PATCH] bcm2835-dma: Limit cyclic transfers on lite channels to 32k
-
-Transfers larger than 32k cause repeated clicking with I2S soundcards.
-The exact reason is yet unknown, so limit to 32k as bcm2708-dmaengine
-did as an intermediate fix.
----
- drivers/dma/bcm2835-dma.c | 8 +++++++-
- 1 file changed, 7 insertions(+), 1 deletion(-)
-
---- a/drivers/dma/bcm2835-dma.c
-+++ b/drivers/dma/bcm2835-dma.c
-@@ -144,6 +144,12 @@ struct bcm2835_desc {
- */
- #define MAX_LITE_TRANSFER (SZ_64K - 4)
-
-+/*
-+ * Transfers larger than 32k cause issues with the bcm2708-i2s driver,
-+ * so limit transfer size to 32k as bcm2708-dmaengine did.
-+ */
-+#define MAX_CYCLIC_LITE_TRANSFER SZ_32K
-+
- static inline struct bcm2835_dmadev *to_bcm2835_dma_dev(struct dma_device *d)
- {
- return container_of(d, struct bcm2835_dmadev, ddev);
-@@ -412,7 +418,7 @@ static struct dma_async_tx_descriptor *b
- d->c = c;
- d->dir = direction;
- if (c->ch >= 8) /* LITE channel */
-- max_size = MAX_LITE_TRANSFER;
-+ max_size = MAX_CYCLIC_LITE_TRANSFER;
- else
- max_size = MAX_NORMAL_TRANSFER;
- period_len = min(period_len, max_size);
diff --git a/target/linux/brcm2708/patches-4.4/0025-bcm2835-Add-support-for-uart1.patch b/target/linux/brcm2708/patches-4.4/0025-bcm2835-Add-support-for-uart1.patch
deleted file mode 100644
index 5f7fd57..0000000
--- a/target/linux/brcm2708/patches-4.4/0025-bcm2835-Add-support-for-uart1.patch
+++ /dev/null
@@ -1,57 +0,0 @@
-From 877a10a2dc756e4dfc6f0183e98467259c08e753 Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Noralf=20Tr=C3=B8nnes?= <noralf at tronnes.org>
-Date: Sat, 15 Aug 2015 20:50:02 +0200
-Subject: [PATCH] bcm2835: Add support for uart1
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-This is a hack until a proper solution is agreed upon.
-Martin Sperl is doing some work in this area.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
----
- arch/arm/mach-bcm/board_bcm2835.c | 25 +++++++++++++++++++++++++
- 1 file changed, 25 insertions(+)
-
---- a/arch/arm/mach-bcm/board_bcm2835.c
-+++ b/arch/arm/mach-bcm/board_bcm2835.c
-@@ -22,6 +22,29 @@
- #include <asm/mach/arch.h>
- #include <asm/mach/map.h>
-
-+/* Use this hack until a proper solution is agreed upon */
-+static void __init bcm2835_init_uart1(void)
-+{
-+ struct device_node *np;
-+
-+ np = of_find_compatible_node(NULL, NULL, "brcm,bcm2835-aux-uart");
-+ if (of_device_is_available(np)) {
-+ np = of_find_compatible_node(NULL, NULL,
-+ "bcrm,bcm2835-aux-enable");
-+ if (np) {
-+ void __iomem *base = of_iomap(np, 0);
-+
-+ if (!base) {
-+ pr_err("bcm2835: Failed enabling Mini UART\n");
-+ return;
-+ }
-+
-+ writel(1, base);
-+ pr_info("bcm2835: Mini UART enabled\n");
-+ }
-+ }
-+}
-+
- static void __init bcm2835_init(void)
- {
- struct device_node *np = of_find_node_by_path("/system");
-@@ -42,6 +65,8 @@ static void __init bcm2835_init(void)
- system_rev = val;
- if (!of_property_read_u64(np, "linux,serial", &val64))
- system_serial_low = val64;
-+
-+ bcm2835_init_uart1();
- }
-
- static const char * const bcm2835_compat[] = {
diff --git a/target/linux/brcm2708/patches-4.4/0026-firmware-bcm2835-Add-missing-property-tags.patch b/target/linux/brcm2708/patches-4.4/0026-firmware-bcm2835-Add-missing-property-tags.patch
deleted file mode 100644
index 5c1604e..0000000
--- a/target/linux/brcm2708/patches-4.4/0026-firmware-bcm2835-Add-missing-property-tags.patch
+++ /dev/null
@@ -1,62 +0,0 @@
-From 3be2b2bdb87296b858efbbf298ae568d8ce94447 Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Noralf=20Tr=C3=B8nnes?= <noralf at tronnes.org>
-Date: Fri, 26 Jun 2015 14:21:20 +0200
-Subject: [PATCH] firmware: bcm2835: Add missing property tags
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
----
- include/soc/bcm2835/raspberrypi-firmware.h | 8 ++++++++
- 1 file changed, 8 insertions(+)
-
---- a/include/soc/bcm2835/raspberrypi-firmware.h
-+++ b/include/soc/bcm2835/raspberrypi-firmware.h
-@@ -63,6 +63,7 @@ enum rpi_firmware_property_tag {
- RPI_FIRMWARE_GET_MIN_VOLTAGE = 0x00030008,
- RPI_FIRMWARE_GET_TURBO = 0x00030009,
- RPI_FIRMWARE_GET_MAX_TEMPERATURE = 0x0003000a,
-+ RPI_FIRMWARE_GET_STC = 0x0003000b,
- RPI_FIRMWARE_ALLOCATE_MEMORY = 0x0003000c,
- RPI_FIRMWARE_LOCK_MEMORY = 0x0003000d,
- RPI_FIRMWARE_UNLOCK_MEMORY = 0x0003000e,
-@@ -72,10 +73,12 @@ enum rpi_firmware_property_tag {
- RPI_FIRMWARE_SET_ENABLE_QPU = 0x00030012,
- RPI_FIRMWARE_GET_DISPMANX_RESOURCE_MEM_HANDLE = 0x00030014,
- RPI_FIRMWARE_GET_EDID_BLOCK = 0x00030020,
-+ RPI_FIRMWARE_GET_CUSTOMER_OTP = 0x00030021,
- RPI_FIRMWARE_SET_CLOCK_STATE = 0x00038001,
- RPI_FIRMWARE_SET_CLOCK_RATE = 0x00038002,
- RPI_FIRMWARE_SET_VOLTAGE = 0x00038003,
- RPI_FIRMWARE_SET_TURBO = 0x00038009,
-+ RPI_FIRMWARE_SET_CUSTOMER_OTP = 0x00038021,
-
- /* Dispmanx TAGS */
- RPI_FIRMWARE_FRAMEBUFFER_ALLOCATE = 0x00040001,
-@@ -89,6 +92,7 @@ enum rpi_firmware_property_tag {
- RPI_FIRMWARE_FRAMEBUFFER_GET_VIRTUAL_OFFSET = 0x00040009,
- RPI_FIRMWARE_FRAMEBUFFER_GET_OVERSCAN = 0x0004000a,
- RPI_FIRMWARE_FRAMEBUFFER_GET_PALETTE = 0x0004000b,
-+ RPI_FIRMWARE_FRAMEBUFFER_GET_TOUCHBUF = 0x0004000f,
- RPI_FIRMWARE_FRAMEBUFFER_RELEASE = 0x00048001,
- RPI_FIRMWARE_FRAMEBUFFER_TEST_PHYSICAL_WIDTH_HEIGHT = 0x00044003,
- RPI_FIRMWARE_FRAMEBUFFER_TEST_VIRTUAL_WIDTH_HEIGHT = 0x00044004,
-@@ -98,6 +102,7 @@ enum rpi_firmware_property_tag {
- RPI_FIRMWARE_FRAMEBUFFER_TEST_VIRTUAL_OFFSET = 0x00044009,
- RPI_FIRMWARE_FRAMEBUFFER_TEST_OVERSCAN = 0x0004400a,
- RPI_FIRMWARE_FRAMEBUFFER_TEST_PALETTE = 0x0004400b,
-+ RPI_FIRMWARE_FRAMEBUFFER_TEST_VSYNC = 0x0004400e,
- RPI_FIRMWARE_FRAMEBUFFER_SET_PHYSICAL_WIDTH_HEIGHT = 0x00048003,
- RPI_FIRMWARE_FRAMEBUFFER_SET_VIRTUAL_WIDTH_HEIGHT = 0x00048004,
- RPI_FIRMWARE_FRAMEBUFFER_SET_DEPTH = 0x00048005,
-@@ -106,6 +111,9 @@ enum rpi_firmware_property_tag {
- RPI_FIRMWARE_FRAMEBUFFER_SET_VIRTUAL_OFFSET = 0x00048009,
- RPI_FIRMWARE_FRAMEBUFFER_SET_OVERSCAN = 0x0004800a,
- RPI_FIRMWARE_FRAMEBUFFER_SET_PALETTE = 0x0004800b,
-+ RPI_FIRMWARE_FRAMEBUFFER_SET_VSYNC = 0x0004800e,
-+
-+ RPI_FIRMWARE_VCHIQ_INIT = 0x00048010,
-
- RPI_FIRMWARE_GET_COMMAND_LINE = 0x00050001,
- RPI_FIRMWARE_GET_DMA_CHANNELS = 0x00060001,
diff --git a/target/linux/brcm2708/patches-4.4/0027-Main-bcm2708-bcm2709-linux-port.patch b/target/linux/brcm2708/patches-4.4/0027-Main-bcm2708-bcm2709-linux-port.patch
deleted file mode 100644
index 9243de8..0000000
--- a/target/linux/brcm2708/patches-4.4/0027-Main-bcm2708-bcm2709-linux-port.patch
+++ /dev/null
@@ -1,2418 +0,0 @@
-From 419131921c0b0b0c7be32f9a2a30d42377f604e2 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Sun, 12 May 2013 12:24:19 +0100
-Subject: [PATCH] Main bcm2708/bcm2709 linux port
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Signed-off-by: popcornmix <popcornmix at gmail.com>
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
----
- arch/arm/Kconfig | 49 +++
- arch/arm/Kconfig.debug | 8 +
- arch/arm/Makefile | 2 +
- arch/arm/kernel/head.S | 8 +
- arch/arm/kernel/process.c | 10 +
- arch/arm/mach-bcm2708/Kconfig | 23 ++
- arch/arm/mach-bcm2708/Makefile | 5 +
- arch/arm/mach-bcm2708/Makefile.boot | 3 +
- arch/arm/mach-bcm2708/bcm2708.c | 231 ++++++++++++
- arch/arm/mach-bcm2708/include/mach/debug-macro.S | 22 ++
- arch/arm/mach-bcm2708/include/mach/io.h | 27 ++
- arch/arm/mach-bcm2708/include/mach/memory.h | 57 +++
- arch/arm/mach-bcm2708/include/mach/platform.h | 112 ++++++
- arch/arm/mach-bcm2708/include/mach/system.h | 37 ++
- arch/arm/mach-bcm2708/include/mach/uncompress.h | 84 +++++
- arch/arm/mach-bcm2708/include/mach/vmalloc.h | 20 ++
- arch/arm/mach-bcm2709/Kconfig | 16 +
- arch/arm/mach-bcm2709/Makefile | 5 +
- arch/arm/mach-bcm2709/Makefile.boot | 3 +
- arch/arm/mach-bcm2709/bcm2709.c | 380 ++++++++++++++++++++
- arch/arm/mach-bcm2709/include/mach/debug-macro.S | 22 ++
- arch/arm/mach-bcm2709/include/mach/entry-macro.S | 123 +++++++
- arch/arm/mach-bcm2709/include/mach/io.h | 27 ++
- arch/arm/mach-bcm2709/include/mach/memory.h | 57 +++
- arch/arm/mach-bcm2709/include/mach/platform.h | 188 ++++++++++
- arch/arm/mach-bcm2709/include/mach/system.h | 37 ++
- arch/arm/mach-bcm2709/include/mach/uncompress.h | 84 +++++
- arch/arm/mach-bcm2709/include/mach/vc_mem.h | 35 ++
- arch/arm/mach-bcm2709/include/mach/vmalloc.h | 20 ++
- arch/arm/mach-bcm2709/vc_mem.c | 431 +++++++++++++++++++++++
- arch/arm/mm/Kconfig | 2 +-
- arch/arm/mm/proc-v6.S | 15 +-
- arch/arm/mm/proc-v7.S | 1 +
- arch/arm/tools/mach-types | 2 +
- drivers/clocksource/Makefile | 2 +-
- drivers/irqchip/Makefile | 3 +
- include/linux/mmc/host.h | 1 +
- 37 files changed, 2147 insertions(+), 5 deletions(-)
- create mode 100644 arch/arm/mach-bcm2708/Kconfig
- create mode 100644 arch/arm/mach-bcm2708/Makefile
- create mode 100644 arch/arm/mach-bcm2708/Makefile.boot
- create mode 100644 arch/arm/mach-bcm2708/bcm2708.c
- create mode 100644 arch/arm/mach-bcm2708/include/mach/debug-macro.S
- create mode 100644 arch/arm/mach-bcm2708/include/mach/io.h
- create mode 100644 arch/arm/mach-bcm2708/include/mach/memory.h
- create mode 100644 arch/arm/mach-bcm2708/include/mach/platform.h
- create mode 100644 arch/arm/mach-bcm2708/include/mach/system.h
- create mode 100644 arch/arm/mach-bcm2708/include/mach/uncompress.h
- create mode 100644 arch/arm/mach-bcm2708/include/mach/vmalloc.h
- create mode 100644 arch/arm/mach-bcm2709/Kconfig
- create mode 100644 arch/arm/mach-bcm2709/Makefile
- create mode 100644 arch/arm/mach-bcm2709/Makefile.boot
- create mode 100644 arch/arm/mach-bcm2709/bcm2709.c
- create mode 100644 arch/arm/mach-bcm2709/include/mach/debug-macro.S
- create mode 100644 arch/arm/mach-bcm2709/include/mach/entry-macro.S
- create mode 100644 arch/arm/mach-bcm2709/include/mach/io.h
- create mode 100644 arch/arm/mach-bcm2709/include/mach/memory.h
- create mode 100644 arch/arm/mach-bcm2709/include/mach/platform.h
- create mode 100644 arch/arm/mach-bcm2709/include/mach/system.h
- create mode 100644 arch/arm/mach-bcm2709/include/mach/uncompress.h
- create mode 100644 arch/arm/mach-bcm2709/include/mach/vc_mem.h
- create mode 100644 arch/arm/mach-bcm2709/include/mach/vmalloc.h
- create mode 100644 arch/arm/mach-bcm2709/vc_mem.c
-
---- a/arch/arm/Kconfig
-+++ b/arch/arm/Kconfig
-@@ -318,6 +318,52 @@ choice
- default ARCH_VERSATILE if !MMU
- default ARCH_MULTIPLATFORM if MMU
-
-+config ARCH_BCM2708
-+ bool "Broadcom BCM2708 family"
-+ select CPU_V6
-+ select ARM_AMBA
-+ select CLKSRC_MMIO
-+ select CLKSRC_OF if OF
-+ select HAVE_SCHED_CLOCK
-+ select NEED_MACH_GPIO_H
-+ select NEED_MACH_MEMORY_H
-+ select COMMON_CLK
-+ select ARCH_HAS_CPUFREQ
-+ select GENERIC_CLOCKEVENTS
-+ select ARM_ERRATA_411920
-+ select MACH_BCM2708
-+ select MULTI_IRQ_HANDLER
-+ select SPARSE_IRQ
-+ select VC4
-+ select FIQ
-+ help
-+ This enables support for Broadcom BCM2708 boards.
-+
-+config ARCH_BCM2709
-+ bool "Broadcom BCM2709 family"
-+ select CPU_V7
-+ select HAVE_SMP
-+ select ARM_AMBA
-+ select MIGHT_HAVE_CACHE_L2X0
-+ select HAVE_SCHED_CLOCK
-+ select NEED_MACH_MEMORY_H
-+ select NEED_MACH_IO_H
-+ select COMMON_CLK
-+ select ARCH_HAS_CPUFREQ
-+ select GENERIC_CLOCKEVENTS
-+ select MACH_BCM2709
-+ select MULTI_IRQ_HANDLER
-+ select SPARSE_IRQ
-+ select MFD_SYSCON
-+ select VC4
-+ select FIQ
-+ select USE_OF
-+ select ARCH_REQUIRE_GPIOLIB
-+ select PINCTRL
-+ select PINCTRL_BCM2835
-+ help
-+ This enables support for Broadcom BCM2709 boards.
-+
- config ARCH_MULTIPLATFORM
- bool "Allow multiple platforms to be selected"
- depends on MMU
-@@ -809,6 +855,9 @@ config ARCH_VIRT
- # Kconfigs may be included either alphabetically (according to the
- # plat- suffix) or along side the corresponding mach-* source.
- #
-+source "arch/arm/mach-bcm2708/Kconfig"
-+source "arch/arm/mach-bcm2709/Kconfig"
-+
- source "arch/arm/mach-mvebu/Kconfig"
-
- source "arch/arm/mach-alpine/Kconfig"
---- a/arch/arm/Kconfig.debug
-+++ b/arch/arm/Kconfig.debug
-@@ -1240,6 +1240,14 @@ choice
- options; the platform specific options are deprecated
- and will be soon removed.
-
-+ config DEBUG_BCM2708_UART0
-+ bool "Broadcom BCM270X UART0 (PL011)"
-+ depends on ARCH_BCM2708 || ARCH_BCM2709
-+ help
-+ Say Y here if you want the debug print routines to direct
-+ their output to UART 0. The port must have been initialised
-+ by the boot-loader before use.
-+
- endchoice
-
- config DEBUG_EXYNOS_UART
---- a/arch/arm/Makefile
-+++ b/arch/arm/Makefile
-@@ -159,6 +159,8 @@ textofs-$(CONFIG_ARCH_AXXIA) := 0x003080
-
- # Machine directory name. This list is sorted alphanumerically
- # by CONFIG_* macro name.
-+machine-$(CONFIG_ARCH_BCM2708) += bcm2708
-+machine-$(CONFIG_ARCH_BCM2709) += bcm2709
- machine-$(CONFIG_ARCH_ALPINE) += alpine
- machine-$(CONFIG_ARCH_AT91) += at91
- machine-$(CONFIG_ARCH_AXXIA) += axxia
---- a/arch/arm/kernel/head.S
-+++ b/arch/arm/kernel/head.S
-@@ -700,6 +700,14 @@ ARM_BE8(rev16 ip, ip)
- ldrcc r7, [r4], #4 @ use branch for delay slot
- bcc 1b
- ret lr
-+ nop
-+ nop
-+ nop
-+ nop
-+ nop
-+ nop
-+ nop
-+ nop
- #endif
- ENDPROC(__fixup_a_pv_table)
-
---- a/arch/arm/kernel/process.c
-+++ b/arch/arm/kernel/process.c
-@@ -91,6 +91,16 @@ void arch_cpu_idle_exit(void)
- ledtrig_cpu(CPU_LED_IDLE_END);
- }
-
-+char bcm2708_reboot_mode = 'h';
-+
-+int __init reboot_setup(char *str)
-+{
-+ bcm2708_reboot_mode = str[0];
-+ return 1;
-+}
-+
-+__setup("reboot=", reboot_setup);
-+
- void __show_regs(struct pt_regs *regs)
- {
- unsigned long flags;
---- /dev/null
-+++ b/arch/arm/mach-bcm2708/Kconfig
-@@ -0,0 +1,23 @@
-+menu "Broadcom BCM2708 Implementations"
-+ depends on ARCH_BCM2708
-+
-+config MACH_BCM2708
-+ bool "Broadcom BCM2708 Development Platform"
-+ select NEED_MACH_MEMORY_H
-+ select NEED_MACH_IO_H
-+ select CPU_V6
-+ select USE_OF
-+ select ARCH_REQUIRE_GPIOLIB
-+ select PINCTRL
-+ select PINCTRL_BCM2835
-+ help
-+ Include support for the Broadcom(R) BCM2708 platform.
-+
-+config BCM2708_NOL2CACHE
-+ bool "Videocore L2 cache disable"
-+ depends on MACH_BCM2708
-+ default n
-+ help
-+ Do not allow ARM to use GPU's L2 cache. Requires disable_l2cache in config.txt.
-+
-+endmenu
---- /dev/null
-+++ b/arch/arm/mach-bcm2708/Makefile
-@@ -0,0 +1,5 @@
-+#
-+# Makefile for the linux kernel.
-+#
-+
-+obj-$(CONFIG_MACH_BCM2708) += bcm2708.o
---- /dev/null
-+++ b/arch/arm/mach-bcm2708/Makefile.boot
-@@ -0,0 +1,3 @@
-+ zreladdr-y := 0x00008000
-+params_phys-y := 0x00000100
-+initrd_phys-y := 0x00800000
---- /dev/null
-+++ b/arch/arm/mach-bcm2708/bcm2708.c
-@@ -0,0 +1,231 @@
-+/*
-+ * linux/arch/arm/mach-bcm2708/bcm2708.c
-+ *
-+ * Copyright (C) 2010 Broadcom
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
-+ */
-+
-+#include <linux/init.h>
-+#include <linux/dma-mapping.h>
-+#include <linux/module.h>
-+#include <linux/of_platform.h>
-+#include <asm/system_info.h>
-+#include <asm/mach-types.h>
-+#include <asm/mach/arch.h>
-+#include <asm/mach/map.h>
-+
-+#include <mach/system.h>
-+
-+#include <linux/broadcom/vc_cma.h>
-+
-+/* Effectively we have an IOMMU (ARM<->VideoCore map) that is set up to
-+ * give us IO access only to 64Mbytes of physical memory (26 bits). We could
-+ * represent this window by setting our dmamasks to 26 bits but, in fact
-+ * we're not going to use addresses outside this range (they're not in real
-+ * memory) so we don't bother.
-+ *
-+ * In the future we might include code to use this IOMMU to remap other
-+ * physical addresses onto VideoCore memory then the use of 32-bits would be
-+ * more legitimate.
-+ */
-+
-+/* command line parameters */
-+static unsigned boardrev, serial;
-+static unsigned reboot_part = 0;
-+
-+static struct map_desc bcm2708_io_desc[] __initdata = {
-+ {
-+ .virtual = IO_ADDRESS(ARMCTRL_BASE),
-+ .pfn = __phys_to_pfn(ARMCTRL_BASE),
-+ .length = SZ_4K,
-+ .type = MT_DEVICE},
-+ {
-+ .virtual = IO_ADDRESS(UART0_BASE),
-+ .pfn = __phys_to_pfn(UART0_BASE),
-+ .length = SZ_4K,
-+ .type = MT_DEVICE},
-+ {
-+ .virtual = IO_ADDRESS(UART1_BASE),
-+ .pfn = __phys_to_pfn(UART1_BASE),
-+ .length = SZ_4K,
-+ .type = MT_DEVICE},
-+ {
-+ .virtual = IO_ADDRESS(DMA_BASE),
-+ .pfn = __phys_to_pfn(DMA_BASE),
-+ .length = SZ_4K,
-+ .type = MT_DEVICE},
-+ {
-+ .virtual = IO_ADDRESS(MCORE_BASE),
-+ .pfn = __phys_to_pfn(MCORE_BASE),
-+ .length = SZ_4K,
-+ .type = MT_DEVICE},
-+ {
-+ .virtual = IO_ADDRESS(ST_BASE),
-+ .pfn = __phys_to_pfn(ST_BASE),
-+ .length = SZ_4K,
-+ .type = MT_DEVICE},
-+ {
-+ .virtual = IO_ADDRESS(USB_BASE),
-+ .pfn = __phys_to_pfn(USB_BASE),
-+ .length = SZ_128K,
-+ .type = MT_DEVICE},
-+ {
-+ .virtual = IO_ADDRESS(PM_BASE),
-+ .pfn = __phys_to_pfn(PM_BASE),
-+ .length = SZ_4K,
-+ .type = MT_DEVICE},
-+ {
-+ .virtual = IO_ADDRESS(GPIO_BASE),
-+ .pfn = __phys_to_pfn(GPIO_BASE),
-+ .length = SZ_4K,
-+ .type = MT_DEVICE}
-+};
-+
-+void __init bcm2708_map_io(void)
-+{
-+ iotable_init(bcm2708_io_desc, ARRAY_SIZE(bcm2708_io_desc));
-+}
-+
-+int calc_rsts(int partition)
-+{
-+ return PM_PASSWORD |
-+ ((partition & (1 << 0)) << 0) |
-+ ((partition & (1 << 1)) << 1) |
-+ ((partition & (1 << 2)) << 2) |
-+ ((partition & (1 << 3)) << 3) |
-+ ((partition & (1 << 4)) << 4) |
-+ ((partition & (1 << 5)) << 5);
-+}
-+
-+static void bcm2708_restart(enum reboot_mode mode, const char *cmd)
-+{
-+ extern char bcm2708_reboot_mode;
-+ uint32_t pm_rstc, pm_wdog;
-+ uint32_t timeout = 10;
-+ uint32_t pm_rsts = 0;
-+
-+ if(bcm2708_reboot_mode == 'q')
-+ {
-+ // NOOBS < 1.3 booting with reboot=q
-+ pm_rsts = readl(__io_address(PM_RSTS));
-+ pm_rsts = PM_PASSWORD | pm_rsts | PM_RSTS_HADWRQ_SET;
-+ }
-+ else if(bcm2708_reboot_mode == 'p')
-+ {
-+ // NOOBS < 1.3 halting
-+ pm_rsts = readl(__io_address(PM_RSTS));
-+ pm_rsts = PM_PASSWORD | pm_rsts | PM_RSTS_HADWRH_SET;
-+ }
-+ else
-+ {
-+ pm_rsts = calc_rsts(reboot_part);
-+ }
-+
-+ writel(pm_rsts, __io_address(PM_RSTS));
-+
-+ /* Setup watchdog for reset */
-+ pm_rstc = readl(__io_address(PM_RSTC));
-+
-+ pm_wdog = PM_PASSWORD | (timeout & PM_WDOG_TIME_SET); // watchdog timer = timer clock / 16; need password (31:16) + value (11:0)
-+ pm_rstc = PM_PASSWORD | (pm_rstc & PM_RSTC_WRCFG_CLR) | PM_RSTC_WRCFG_FULL_RESET;
-+
-+ writel(pm_wdog, __io_address(PM_WDOG));
-+ writel(pm_rstc, __io_address(PM_RSTC));
-+}
-+
-+/* We can't really power off, but if we do the normal reset scheme, and indicate to bootcode.bin not to reboot, then most of the chip will be powered off */
-+static void bcm2708_power_off(void)
-+{
-+ extern char bcm2708_reboot_mode;
-+ if(bcm2708_reboot_mode == 'q')
-+ {
-+ // NOOBS < v1.3
-+ bcm2708_restart('p', "");
-+ }
-+ else
-+ {
-+ /* partition 63 is special code for HALT the bootloader knows not to boot*/
-+ reboot_part = 63;
-+ /* continue with normal reset mechanism */
-+ bcm2708_restart(0, "");
-+ }
-+}
-+
-+static void __init bcm2708_init_uart1(void)
-+{
-+ struct device_node *np;
-+
-+ np = of_find_compatible_node(NULL, NULL, "brcm,bcm2835-aux-uart");
-+ if (of_device_is_available(np)) {
-+ pr_info("bcm2708: Mini UART enabled\n");
-+ writel(1, __io_address(UART1_BASE + 0x4));
-+ }
-+}
-+
-+void __init bcm2708_init(void)
-+{
-+ int ret;
-+
-+ vc_cma_early_init();
-+
-+ pm_power_off = bcm2708_power_off;
-+
-+ ret = of_platform_populate(NULL, of_default_bus_match_table, NULL,
-+ NULL);
-+ if (ret) {
-+ pr_err("of_platform_populate failed: %d\n", ret);
-+ BUG();
-+ }
-+
-+ bcm2708_init_uart1();
-+
-+ system_rev = boardrev;
-+ system_serial_low = serial;
-+}
-+
-+void __init bcm2708_init_early(void)
-+{
-+ /*
-+ * Some devices allocate their coherent buffers from atomic
-+ * context. Increase size of atomic coherent pool to make sure such
-+ * the allocations won't fail.
-+ */
-+ init_dma_coherent_pool_size(SZ_4M);
-+}
-+
-+static void __init board_reserve(void)
-+{
-+ vc_cma_reserve();
-+}
-+
-+static const char * const bcm2708_compat[] = {
-+ "brcm,bcm2708",
-+ NULL
-+};
-+
-+MACHINE_START(BCM2708, "BCM2708")
-+ /* Maintainer: Broadcom Europe Ltd. */
-+ .map_io = bcm2708_map_io,
-+ .init_machine = bcm2708_init,
-+ .init_early = bcm2708_init_early,
-+ .reserve = board_reserve,
-+ .restart = bcm2708_restart,
-+ .dt_compat = bcm2708_compat,
-+MACHINE_END
-+
-+module_param(boardrev, uint, 0644);
-+module_param(serial, uint, 0644);
-+module_param(reboot_part, uint, 0644);
---- /dev/null
-+++ b/arch/arm/mach-bcm2708/include/mach/debug-macro.S
-@@ -0,0 +1,22 @@
-+/* arch/arm/mach-bcm2708/include/mach/debug-macro.S
-+ *
-+ * Debugging macro include header
-+ *
-+ * Copyright (C) 2010 Broadcom
-+ * Copyright (C) 1994-1999 Russell King
-+ * Moved from linux/arch/arm/kernel/debug.S by Ben Dooks
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ *
-+*/
-+
-+#include <mach/platform.h>
-+
-+ .macro addruart, rp, rv, tmp
-+ ldr \rp, =UART0_BASE
-+ ldr \rv, =IO_ADDRESS(UART0_BASE)
-+ .endm
-+
-+#include <debug/pl01x.S>
---- /dev/null
-+++ b/arch/arm/mach-bcm2708/include/mach/io.h
-@@ -0,0 +1,27 @@
-+/*
-+ * arch/arm/mach-bcm2708/include/mach/io.h
-+ *
-+ * Copyright (C) 2003 ARM Limited
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
-+ */
-+#ifndef __ASM_ARM_ARCH_IO_H
-+#define __ASM_ARM_ARCH_IO_H
-+
-+#define IO_SPACE_LIMIT 0xffffffff
-+
-+#define __io(a) __typesafe_io(a)
-+
-+#endif
---- /dev/null
-+++ b/arch/arm/mach-bcm2708/include/mach/memory.h
-@@ -0,0 +1,57 @@
-+/*
-+ * arch/arm/mach-bcm2708/include/mach/memory.h
-+ *
-+ * Copyright (C) 2010 Broadcom
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
-+ */
-+#ifndef __ASM_ARCH_MEMORY_H
-+#define __ASM_ARCH_MEMORY_H
-+
-+/* Memory overview:
-+
-+ [ARMcore] <--virtual addr-->
-+ [ARMmmu] <--physical addr-->
-+ [GERTmap] <--bus add-->
-+ [VCperiph]
-+
-+*/
-+
-+/*
-+ * Physical DRAM offset.
-+ */
-+#define BCM_PLAT_PHYS_OFFSET UL(0x00000000)
-+#define VC_ARMMEM_OFFSET UL(0x00000000) /* offset in VC of ARM memory */
-+
-+#ifdef CONFIG_BCM2708_NOL2CACHE
-+ #define _REAL_BUS_OFFSET UL(0xC0000000) /* don't use L1 or L2 caches */
-+#else
-+ #define _REAL_BUS_OFFSET UL(0x40000000) /* use L2 cache */
-+#endif
-+
-+/* We're using the memory at 64M in the VideoCore for Linux - this adjustment
-+ * will provide the offset into this area as well as setting the bits that
-+ * stop the L1 and L2 cache from being used
-+ *
-+ * WARNING: this only works because the ARM is given memory at a fixed location
-+ * (ARMMEM_OFFSET)
-+ */
-+#define BUS_OFFSET (VC_ARMMEM_OFFSET + _REAL_BUS_OFFSET)
-+#define __virt_to_bus(x) ((x) + (BUS_OFFSET - PAGE_OFFSET))
-+#define __bus_to_virt(x) ((x) - (BUS_OFFSET - PAGE_OFFSET))
-+#define __pfn_to_bus(x) (__pfn_to_phys(x) + (BUS_OFFSET - BCM_PLAT_PHYS_OFFSET))
-+#define __bus_to_pfn(x) __phys_to_pfn((x) - (BUS_OFFSET - BCM_PLAT_PHYS_OFFSET))
-+
-+#endif
---- /dev/null
-+++ b/arch/arm/mach-bcm2708/include/mach/platform.h
-@@ -0,0 +1,112 @@
-+/*
-+ * arch/arm/mach-bcm2708/include/mach/platform.h
-+ *
-+ * Copyright (C) 2010 Broadcom
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
-+ */
-+
-+#ifndef _BCM2708_PLATFORM_H
-+#define _BCM2708_PLATFORM_H
-+
-+
-+/* macros to get at IO space when running virtually */
-+#define IO_ADDRESS(x) (((x) & 0x0fffffff) + (((x) >> 4) & 0x0f000000) + 0xf0000000)
-+
-+#define __io_address(n) IOMEM(IO_ADDRESS(n))
-+
-+
-+/*
-+ * SDRAM
-+ */
-+#define BCM2708_SDRAM_BASE 0x00000000
-+
-+/*
-+ * Logic expansion modules
-+ *
-+ */
-+
-+
-+/* ------------------------------------------------------------------------
-+ * BCM2708 ARMCTRL Registers
-+ * ------------------------------------------------------------------------
-+ */
-+
-+#define HW_REGISTER_RW(addr) (addr)
-+#define HW_REGISTER_RO(addr) (addr)
-+
-+/*
-+ * Definitions and addresses for the ARM CONTROL logic
-+ * This file is manually generated.
-+ */
-+
-+#define BCM2708_PERI_BASE 0x20000000
-+#define IC0_BASE (BCM2708_PERI_BASE + 0x2000)
-+#define ST_BASE (BCM2708_PERI_BASE + 0x3000) /* System Timer */
-+#define MPHI_BASE (BCM2708_PERI_BASE + 0x6000) /* Message -based Parallel Host Interface */
-+#define DMA_BASE (BCM2708_PERI_BASE + 0x7000) /* DMA controller */
-+#define ARM_BASE (BCM2708_PERI_BASE + 0xB000) /* BCM2708 ARM control block */
-+#define PM_BASE (BCM2708_PERI_BASE + 0x100000) /* Power Management, Reset controller and Watchdog registers */
-+#define PCM_CLOCK_BASE (BCM2708_PERI_BASE + 0x101098) /* PCM Clock */
-+#define RNG_BASE (BCM2708_PERI_BASE + 0x104000) /* Hardware RNG */
-+#define GPIO_BASE (BCM2708_PERI_BASE + 0x200000) /* GPIO */
-+#define UART0_BASE (BCM2708_PERI_BASE + 0x201000) /* Uart 0 */
-+#define MMCI0_BASE (BCM2708_PERI_BASE + 0x202000) /* MMC interface */
-+#define I2S_BASE (BCM2708_PERI_BASE + 0x203000) /* I2S */
-+#define SPI0_BASE (BCM2708_PERI_BASE + 0x204000) /* SPI0 */
-+#define BSC0_BASE (BCM2708_PERI_BASE + 0x205000) /* BSC0 I2C/TWI */
-+#define UART1_BASE (BCM2708_PERI_BASE + 0x215000) /* Uart 1 */
-+#define EMMC_BASE (BCM2708_PERI_BASE + 0x300000) /* eMMC interface */
-+#define SMI_BASE (BCM2708_PERI_BASE + 0x600000) /* SMI */
-+#define BSC1_BASE (BCM2708_PERI_BASE + 0x804000) /* BSC1 I2C/TWI */
-+#define USB_BASE (BCM2708_PERI_BASE + 0x980000) /* DTC_OTG USB controller */
-+#define MCORE_BASE (BCM2708_PERI_BASE + 0x0000) /* Fake frame buffer device (actually the multicore sync block*/
-+
-+#define ARMCTRL_BASE (ARM_BASE + 0x000)
-+#define ARMCTRL_IC_BASE (ARM_BASE + 0x200) /* ARM interrupt controller */
-+#define ARMCTRL_TIMER0_1_BASE (ARM_BASE + 0x400) /* Timer 0 and 1 */
-+#define ARMCTRL_0_SBM_BASE (ARM_BASE + 0x800) /* User 0 (ARM)'s Semaphores Doorbells and Mailboxes */
-+
-+/*
-+ * Watchdog
-+ */
-+#define PM_RSTC (PM_BASE+0x1c)
-+#define PM_RSTS (PM_BASE+0x20)
-+#define PM_WDOG (PM_BASE+0x24)
-+
-+#define PM_WDOG_RESET 0000000000
-+#define PM_PASSWORD 0x5a000000
-+#define PM_WDOG_TIME_SET 0x000fffff
-+#define PM_RSTC_WRCFG_CLR 0xffffffcf
-+#define PM_RSTC_WRCFG_SET 0x00000030
-+#define PM_RSTC_WRCFG_FULL_RESET 0x00000020
-+#define PM_RSTC_RESET 0x00000102
-+
-+#define PM_RSTS_HADPOR_SET 0x00001000
-+#define PM_RSTS_HADSRH_SET 0x00000400
-+#define PM_RSTS_HADSRF_SET 0x00000200
-+#define PM_RSTS_HADSRQ_SET 0x00000100
-+#define PM_RSTS_HADWRH_SET 0x00000040
-+#define PM_RSTS_HADWRF_SET 0x00000020
-+#define PM_RSTS_HADWRQ_SET 0x00000010
-+#define PM_RSTS_HADDRH_SET 0x00000004
-+#define PM_RSTS_HADDRF_SET 0x00000002
-+#define PM_RSTS_HADDRQ_SET 0x00000001
-+
-+#define UART0_CLOCK 3000000
-+
-+#endif
-+
-+/* END */
---- /dev/null
-+++ b/arch/arm/mach-bcm2708/include/mach/system.h
-@@ -0,0 +1,37 @@
-+/*
-+ * arch/arm/mach-bcm2708/include/mach/system.h
-+ *
-+ * Copyright (C) 2010 Broadcom
-+ * Copyright (C) 2003 ARM Limited
-+ * Copyright (C) 2000 Deep Blue Solutions Ltd
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
-+ */
-+#ifndef __ASM_ARCH_SYSTEM_H
-+#define __ASM_ARCH_SYSTEM_H
-+
-+#include <linux/io.h>
-+#include <mach/platform.h>
-+
-+static inline void arch_idle(void)
-+{
-+ /*
-+ * This should do all the clock switching
-+ * and wait for interrupt tricks
-+ */
-+ cpu_do_idle();
-+}
-+
-+#endif
---- /dev/null
-+++ b/arch/arm/mach-bcm2708/include/mach/uncompress.h
-@@ -0,0 +1,84 @@
-+/*
-+ * arch/arm/mach-bcn2708/include/mach/uncompress.h
-+ *
-+ * Copyright (C) 2010 Broadcom
-+ * Copyright (C) 2003 ARM Limited
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
-+ */
-+
-+#include <linux/io.h>
-+#include <linux/amba/serial.h>
-+#include <mach/platform.h>
-+
-+#define UART_BAUD 115200
-+
-+#define BCM2708_UART_DR __io(UART0_BASE + UART01x_DR)
-+#define BCM2708_UART_FR __io(UART0_BASE + UART01x_FR)
-+#define BCM2708_UART_IBRD __io(UART0_BASE + UART011_IBRD)
-+#define BCM2708_UART_FBRD __io(UART0_BASE + UART011_FBRD)
-+#define BCM2708_UART_LCRH __io(UART0_BASE + UART011_LCRH)
-+#define BCM2708_UART_CR __io(UART0_BASE + UART011_CR)
-+
-+/*
-+ * This does not append a newline
-+ */
-+static inline void putc(int c)
-+{
-+ while (__raw_readl(BCM2708_UART_FR) & UART01x_FR_TXFF)
-+ barrier();
-+
-+ __raw_writel(c, BCM2708_UART_DR);
-+}
-+
-+static inline void flush(void)
-+{
-+ int fr;
-+
-+ do {
-+ fr = __raw_readl(BCM2708_UART_FR);
-+ barrier();
-+ } while ((fr & (UART011_FR_TXFE | UART01x_FR_BUSY)) != UART011_FR_TXFE);
-+}
-+
-+static inline void arch_decomp_setup(void)
-+{
-+ int temp, div, rem, frac;
-+
-+ temp = 16 * UART_BAUD;
-+ div = UART0_CLOCK / temp;
-+ rem = UART0_CLOCK % temp;
-+ temp = (8 * rem) / UART_BAUD;
-+ frac = (temp >> 1) + (temp & 1);
-+
-+ /* Make sure the UART is disabled before we start */
-+ __raw_writel(0, BCM2708_UART_CR);
-+
-+ /* Set the baud rate */
-+ __raw_writel(div, BCM2708_UART_IBRD);
-+ __raw_writel(frac, BCM2708_UART_FBRD);
-+
-+ /* Set the UART to 8n1, FIFO enabled */
-+ __raw_writel(UART01x_LCRH_WLEN_8 | UART01x_LCRH_FEN, BCM2708_UART_LCRH);
-+
-+ /* Enable the UART */
-+ __raw_writel(UART01x_CR_UARTEN | UART011_CR_TXE | UART011_CR_RXE,
-+ BCM2708_UART_CR);
-+}
-+
-+/*
-+ * nothing to do
-+ */
-+#define arch_decomp_wdog()
---- /dev/null
-+++ b/arch/arm/mach-bcm2708/include/mach/vmalloc.h
-@@ -0,0 +1,20 @@
-+/*
-+ * arch/arm/mach-bcm2708/include/mach/vmalloc.h
-+ *
-+ * Copyright (C) 2010 Broadcom
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
-+ */
-+#define VMALLOC_END (0xe8000000)
---- /dev/null
-+++ b/arch/arm/mach-bcm2709/Kconfig
-@@ -0,0 +1,16 @@
-+menu "Broadcom BCM2709 Implementations"
-+ depends on ARCH_BCM2709
-+
-+config MACH_BCM2709
-+ bool "Broadcom BCM2709 Development Platform"
-+ help
-+ Include support for the Broadcom(R) BCM2709 platform.
-+
-+config BCM2708_NOL2CACHE
-+ bool "Videocore L2 cache disable"
-+ depends on MACH_BCM2709
-+ default y
-+ help
-+ Do not allow ARM to use GPU's L2 cache. Requires disable_l2cache in config.txt.
-+
-+endmenu
---- /dev/null
-+++ b/arch/arm/mach-bcm2709/Makefile
-@@ -0,0 +1,5 @@
-+#
-+# Makefile for the linux kernel.
-+#
-+
-+obj-$(CONFIG_MACH_BCM2709) += bcm2709.o
---- /dev/null
-+++ b/arch/arm/mach-bcm2709/Makefile.boot
-@@ -0,0 +1,3 @@
-+ zreladdr-y := 0x00008000
-+params_phys-y := 0x00000100
-+initrd_phys-y := 0x00800000
---- /dev/null
-+++ b/arch/arm/mach-bcm2709/bcm2709.c
-@@ -0,0 +1,380 @@
-+/*
-+ * linux/arch/arm/mach-bcm2709/bcm2709.c
-+ *
-+ * Copyright (C) 2010 Broadcom
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
-+ */
-+
-+#include <linux/init.h>
-+#include <linux/dma-mapping.h>
-+#include <linux/interrupt.h>
-+#include <linux/clk-provider.h>
-+#include <linux/clocksource.h>
-+#include <linux/io.h>
-+#include <linux/module.h>
-+#include <linux/of_platform.h>
-+
-+#include <asm/system_info.h>
-+#include <asm/mach-types.h>
-+#include <asm/cputype.h>
-+
-+#include <asm/mach/arch.h>
-+#include <asm/mach/map.h>
-+
-+#include <mach/system.h>
-+
-+#include <linux/broadcom/vc_cma.h>
-+
-+/* Effectively we have an IOMMU (ARM<->VideoCore map) that is set up to
-+ * give us IO access only to 64Mbytes of physical memory (26 bits). We could
-+ * represent this window by setting our dmamasks to 26 bits but, in fact
-+ * we're not going to use addresses outside this range (they're not in real
-+ * memory) so we don't bother.
-+ *
-+ * In the future we might include code to use this IOMMU to remap other
-+ * physical addresses onto VideoCore memory then the use of 32-bits would be
-+ * more legitimate.
-+ */
-+
-+/* command line parameters */
-+static unsigned boardrev, serial;
-+static unsigned reboot_part = 0;
-+
-+static struct map_desc bcm2709_io_desc[] __initdata = {
-+ {
-+ .virtual = IO_ADDRESS(ARMCTRL_BASE),
-+ .pfn = __phys_to_pfn(ARMCTRL_BASE),
-+ .length = SZ_4K,
-+ .type = MT_DEVICE},
-+ {
-+ .virtual = IO_ADDRESS(UART0_BASE),
-+ .pfn = __phys_to_pfn(UART0_BASE),
-+ .length = SZ_4K,
-+ .type = MT_DEVICE},
-+ {
-+ .virtual = IO_ADDRESS(UART1_BASE),
-+ .pfn = __phys_to_pfn(UART1_BASE),
-+ .length = SZ_4K,
-+ .type = MT_DEVICE},
-+ {
-+ .virtual = IO_ADDRESS(DMA_BASE),
-+ .pfn = __phys_to_pfn(DMA_BASE),
-+ .length = SZ_4K,
-+ .type = MT_DEVICE},
-+ {
-+ .virtual = IO_ADDRESS(MCORE_BASE),
-+ .pfn = __phys_to_pfn(MCORE_BASE),
-+ .length = SZ_4K,
-+ .type = MT_DEVICE},
-+ {
-+ .virtual = IO_ADDRESS(ST_BASE),
-+ .pfn = __phys_to_pfn(ST_BASE),
-+ .length = SZ_4K,
-+ .type = MT_DEVICE},
-+ {
-+ .virtual = IO_ADDRESS(USB_BASE),
-+ .pfn = __phys_to_pfn(USB_BASE),
-+ .length = SZ_128K,
-+ .type = MT_DEVICE},
-+ {
-+ .virtual = IO_ADDRESS(PM_BASE),
-+ .pfn = __phys_to_pfn(PM_BASE),
-+ .length = SZ_4K,
-+ .type = MT_DEVICE},
-+ {
-+ .virtual = IO_ADDRESS(GPIO_BASE),
-+ .pfn = __phys_to_pfn(GPIO_BASE),
-+ .length = SZ_4K,
-+ .type = MT_DEVICE},
-+ {
-+ .virtual = IO_ADDRESS(ARM_LOCAL_BASE),
-+ .pfn = __phys_to_pfn(ARM_LOCAL_BASE),
-+ .length = SZ_4K,
-+ .type = MT_DEVICE},
-+};
-+
-+void __init bcm2709_map_io(void)
-+{
-+ iotable_init(bcm2709_io_desc, ARRAY_SIZE(bcm2709_io_desc));
-+}
-+
-+int calc_rsts(int partition)
-+{
-+ return PM_PASSWORD |
-+ ((partition & (1 << 0)) << 0) |
-+ ((partition & (1 << 1)) << 1) |
-+ ((partition & (1 << 2)) << 2) |
-+ ((partition & (1 << 3)) << 3) |
-+ ((partition & (1 << 4)) << 4) |
-+ ((partition & (1 << 5)) << 5);
-+}
-+
-+static void bcm2709_restart(enum reboot_mode mode, const char *cmd)
-+{
-+ extern char bcm2708_reboot_mode;
-+ uint32_t pm_rstc, pm_wdog;
-+ uint32_t timeout = 10;
-+ uint32_t pm_rsts = 0;
-+
-+ if(bcm2708_reboot_mode == 'q')
-+ {
-+ // NOOBS < 1.3 booting with reboot=q
-+ pm_rsts = readl(__io_address(PM_RSTS));
-+ pm_rsts = PM_PASSWORD | pm_rsts | PM_RSTS_HADWRQ_SET;
-+ }
-+ else if(bcm2708_reboot_mode == 'p')
-+ {
-+ // NOOBS < 1.3 halting
-+ pm_rsts = readl(__io_address(PM_RSTS));
-+ pm_rsts = PM_PASSWORD | pm_rsts | PM_RSTS_HADWRH_SET;
-+ }
-+ else
-+ {
-+ pm_rsts = calc_rsts(reboot_part);
-+ }
-+
-+ writel(pm_rsts, __io_address(PM_RSTS));
-+
-+ /* Setup watchdog for reset */
-+ pm_rstc = readl(__io_address(PM_RSTC));
-+
-+ pm_wdog = PM_PASSWORD | (timeout & PM_WDOG_TIME_SET); // watchdog timer = timer clock / 16; need password (31:16) + value (11:0)
-+ pm_rstc = PM_PASSWORD | (pm_rstc & PM_RSTC_WRCFG_CLR) | PM_RSTC_WRCFG_FULL_RESET;
-+
-+ writel(pm_wdog, __io_address(PM_WDOG));
-+ writel(pm_rstc, __io_address(PM_RSTC));
-+}
-+
-+/* We can't really power off, but if we do the normal reset scheme, and indicate to bootcode.bin not to reboot, then most of the chip will be powered off */
-+static void bcm2709_power_off(void)
-+{
-+ extern char bcm2708_reboot_mode;
-+ if(bcm2708_reboot_mode == 'q')
-+ {
-+ // NOOBS < v1.3
-+ bcm2709_restart('p', "");
-+ }
-+ else
-+ {
-+ /* partition 63 is special code for HALT the bootloader knows not to boot*/
-+ reboot_part = 63;
-+ /* continue with normal reset mechanism */
-+ bcm2709_restart(0, "");
-+ }
-+}
-+
-+static void __init bcm2709_init_uart1(void)
-+{
-+ struct device_node *np;
-+
-+ np = of_find_compatible_node(NULL, NULL, "brcm,bcm2835-aux-uart");
-+ if (of_device_is_available(np)) {
-+ pr_info("bcm2709: Mini UART enabled\n");
-+ writel(1, __io_address(UART1_BASE + 0x4));
-+ }
-+}
-+
-+void __init bcm2709_init(void)
-+{
-+ int ret;
-+
-+ vc_cma_early_init();
-+
-+ pm_power_off = bcm2709_power_off;
-+
-+ ret = of_platform_populate(NULL, of_default_bus_match_table, NULL,
-+ NULL);
-+ if (ret) {
-+ pr_err("of_platform_populate failed: %d\n", ret);
-+ BUG();
-+ }
-+
-+ bcm2709_init_uart1();
-+
-+ system_rev = boardrev;
-+ system_serial_low = serial;
-+}
-+
-+static void __init bcm2709_timer_init(void)
-+{
-+ // timer control
-+ writel(0, __io_address(ARM_LOCAL_CONTROL));
-+ // timer pre_scaler
-+ writel(0x80000000, __io_address(ARM_LOCAL_PRESCALER)); // 19.2MHz
-+ //writel(0x06AAAAAB, __io_address(ARM_LOCAL_PRESCALER)); // 1MHz
-+
-+ of_clk_init(NULL);
-+ clocksource_probe();
-+}
-+
-+
-+void __init bcm2709_init_early(void)
-+{
-+ /*
-+ * Some devices allocate their coherent buffers from atomic
-+ * context. Increase size of atomic coherent pool to make sure such
-+ * the allocations won't fail.
-+ */
-+ init_dma_coherent_pool_size(SZ_4M);
-+}
-+
-+static void __init board_reserve(void)
-+{
-+ vc_cma_reserve();
-+}
-+
-+
-+#ifdef CONFIG_SMP
-+#include <linux/smp.h>
-+
-+#include <asm/cacheflush.h>
-+#include <asm/smp_plat.h>
-+int dc4=0;
-+//void dc4_log(unsigned x) { if (dc4) writel((x), __io_address(ST_BASE+10 + raw_smp_processor_id()*4)); }
-+void dc4_log_dead(unsigned x) { if (dc4) writel((readl(__io_address(ST_BASE+0x10 + raw_smp_processor_id()*4)) & 0xffff) | ((x)<<16), __io_address(ST_BASE+0x10 + raw_smp_processor_id()*4)); }
-+
-+static void bcm2835_send_doorbell(const struct cpumask *mask, unsigned int irq)
-+{
-+ int cpu;
-+ /*
-+ * Ensure that stores to Normal memory are visible to the
-+ * other CPUs before issuing the IPI.
-+ */
-+ dsb();
-+
-+ /* Convert our logical CPU mask into a physical one. */
-+ for_each_cpu(cpu, mask)
-+ {
-+ /* submit softirq */
-+ writel(1<<irq, __io_address(ARM_LOCAL_MAILBOX0_SET0 + 0x10 * MPIDR_AFFINITY_LEVEL(cpu_logical_map(cpu), 0)));
-+ }
-+}
-+
-+void __init bcm2709_smp_init_cpus(void)
-+{
-+ void secondary_startup(void);
-+ unsigned int i, ncores;
-+
-+ ncores = 4; // xxx scu_get_core_count(NULL);
-+ printk("[%s] enter (%x->%x)\n", __FUNCTION__, (unsigned)virt_to_phys((void *)secondary_startup), (unsigned)__io_address(ST_BASE + 0x10));
-+ printk("[%s] ncores=%d\n", __FUNCTION__, ncores);
-+
-+ for (i = 0; i < ncores; i++) {
-+ set_cpu_possible(i, true);
-+ /* enable IRQ (not FIQ) */
-+ writel(0x1, __io_address(ARM_LOCAL_MAILBOX_INT_CONTROL0 + 0x4 * i));
-+ //writel(0xf, __io_address(ARM_LOCAL_TIMER_INT_CONTROL0 + 0x4 * i));
-+ }
-+ set_smp_cross_call(bcm2835_send_doorbell);
-+}
-+
-+/*
-+ * for arch/arm/kernel/smp.c:smp_prepare_cpus(unsigned int max_cpus)
-+ */
-+void __init bcm2709_smp_prepare_cpus(unsigned int max_cpus)
-+{
-+ //void __iomem *scu_base;
-+
-+ printk("[%s] enter\n", __FUNCTION__);
-+ //scu_base = scu_base_addr();
-+ //scu_enable(scu_base);
-+}
-+
-+/*
-+ * for linux/arch/arm/kernel/smp.c:secondary_start_kernel(void)
-+ */
-+void __init bcm2709_secondary_init(unsigned int cpu)
-+{
-+ printk("[%s] enter cpu:%d\n", __FUNCTION__, cpu);
-+ //gic_secondary_init(0);
-+}
-+
-+/*
-+ * for linux/arch/arm/kernel/smp.c:__cpu_up(..)
-+ */
-+int __init bcm2709_boot_secondary(unsigned int cpu, struct task_struct *idle)
-+{
-+ void secondary_startup(void);
-+ void *mbox_set = __io_address(ARM_LOCAL_MAILBOX3_SET0 + 0x10 * MPIDR_AFFINITY_LEVEL(cpu_logical_map(cpu), 0));
-+ void *mbox_clr = __io_address(ARM_LOCAL_MAILBOX3_CLR0 + 0x10 * MPIDR_AFFINITY_LEVEL(cpu_logical_map(cpu), 0));
-+ unsigned secondary_boot = (unsigned)virt_to_phys((void *)secondary_startup);
-+ int timeout=20;
-+ unsigned t = -1;
-+ //printk("[%s] enter cpu:%d (%x->%p) %x\n", __FUNCTION__, cpu, secondary_boot, wake, readl(wake));
-+
-+ dsb();
-+ BUG_ON(readl(mbox_clr) != 0);
-+ writel(secondary_boot, mbox_set);
-+
-+ while (--timeout > 0) {
-+ t = readl(mbox_clr);
-+ if (t == 0) break;
-+ cpu_relax();
-+ }
-+ if (timeout==0)
-+ printk("[%s] cpu:%d failed to start (%x)\n", __FUNCTION__, cpu, t);
-+ else
-+ printk("[%s] cpu:%d started (%x) %d\n", __FUNCTION__, cpu, t, timeout);
-+
-+ return 0;
-+}
-+
-+
-+struct smp_operations bcm2709_smp_ops __initdata = {
-+ .smp_init_cpus = bcm2709_smp_init_cpus,
-+ .smp_prepare_cpus = bcm2709_smp_prepare_cpus,
-+ .smp_secondary_init = bcm2709_secondary_init,
-+ .smp_boot_secondary = bcm2709_boot_secondary,
-+};
-+#endif
-+
-+static const char * const bcm2709_compat[] = {
-+ "brcm,bcm2709",
-+ "brcm,bcm2708", /* Could use bcm2708 in a pinch */
-+ NULL
-+};
-+
-+MACHINE_START(BCM2709, "BCM2709")
-+ /* Maintainer: Broadcom Europe Ltd. */
-+#ifdef CONFIG_SMP
-+ .smp = smp_ops(bcm2709_smp_ops),
-+#endif
-+ .map_io = bcm2709_map_io,
-+ .init_time = bcm2709_timer_init,
-+ .init_machine = bcm2709_init,
-+ .init_early = bcm2709_init_early,
-+ .reserve = board_reserve,
-+ .restart = bcm2709_restart,
-+ .dt_compat = bcm2709_compat,
-+MACHINE_END
-+
-+MACHINE_START(BCM2708, "BCM2709")
-+ /* Maintainer: Broadcom Europe Ltd. */
-+#ifdef CONFIG_SMP
-+ .smp = smp_ops(bcm2709_smp_ops),
-+#endif
-+ .map_io = bcm2709_map_io,
-+ .init_time = bcm2709_timer_init,
-+ .init_machine = bcm2709_init,
-+ .init_early = bcm2709_init_early,
-+ .reserve = board_reserve,
-+ .restart = bcm2709_restart,
-+ .dt_compat = bcm2709_compat,
-+MACHINE_END
-+
-+module_param(boardrev, uint, 0644);
-+module_param(serial, uint, 0644);
-+module_param(reboot_part, uint, 0644);
---- /dev/null
-+++ b/arch/arm/mach-bcm2709/include/mach/debug-macro.S
-@@ -0,0 +1,22 @@
-+/* arch/arm/mach-bcm2708/include/mach/debug-macro.S
-+ *
-+ * Debugging macro include header
-+ *
-+ * Copyright (C) 2010 Broadcom
-+ * Copyright (C) 1994-1999 Russell King
-+ * Moved from linux/arch/arm/kernel/debug.S by Ben Dooks
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ *
-+*/
-+
-+#include <mach/platform.h>
-+
-+ .macro addruart, rp, rv, tmp
-+ ldr \rp, =UART0_BASE
-+ ldr \rv, =IO_ADDRESS(UART0_BASE)
-+ .endm
-+
-+#include <debug/pl01x.S>
---- /dev/null
-+++ b/arch/arm/mach-bcm2709/include/mach/entry-macro.S
-@@ -0,0 +1,123 @@
-+/*
-+ * arch/arm/mach-bcm2708/include/mach/entry-macro.S
-+ *
-+ * Low-level IRQ helper macros for BCM2708 platforms
-+ *
-+ * Copyright (C) 2010 Broadcom
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
-+ */
-+#include <mach/hardware.h>
-+#include <mach/irqs.h>
-+
-+ .macro disable_fiq
-+ .endm
-+
-+ .macro get_irqnr_preamble, base, tmp
-+ ldr \base, =IO_ADDRESS(ARMCTRL_IC_BASE)
-+ .endm
-+
-+ .macro arch_ret_to_user, tmp1, tmp2
-+ .endm
-+
-+ .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
-+ /* get core number */
-+ mrc p15, 0, \tmp, c0, c0, 5
-+ ubfx \tmp, \tmp, #0, #2
-+
-+ /* get core's local interrupt controller */
-+ ldr \irqstat, = __io_address(ARM_LOCAL_IRQ_PENDING0) @ local interrupt source
-+ add \irqstat, \irqstat, \tmp, lsl #2
-+ ldr \tmp, [\irqstat]
-+ /* ignore gpu interrupt */
-+ bic \tmp, #0x100
-+ /* ignore mailbox interrupts */
-+ bics \tmp, #0xf0
-+ beq 1005f
-+
-+ @ For non-zero x, LSB(x) = 31 - CLZ(x^(x-1))
-+ @ N.B. CLZ is an ARM5 instruction.
-+ mov \irqnr, #(ARM_IRQ_LOCAL_BASE + 31)
-+ sub \irqstat, \tmp, #1
-+ eor \irqstat, \irqstat, \tmp
-+ clz \tmp, \irqstat
-+ sub \irqnr, \tmp
-+ b 1020f
-+1005:
-+ /* get core number */
-+ mrc p15, 0, \tmp, c0, c0, 5
-+ ubfx \tmp, \tmp, #0, #2
-+
-+ cmp \tmp, #1
-+ beq 1020f
-+ cmp \tmp, #2
-+ beq 1020f
-+ cmp \tmp, #3
-+ beq 1020f
-+
-+ /* get masked status */
-+ ldr \irqstat, [\base, #(ARM_IRQ_PEND0 - ARMCTRL_IC_BASE)]
-+ mov \irqnr, #(ARM_IRQ0_BASE + 31)
-+ and \tmp, \irqstat, #0x300 @ save bits 8 and 9
-+ /* clear bits 8 and 9, and test */
-+ bics \irqstat, \irqstat, #0x300
-+ bne 1010f
-+
-+ tst \tmp, #0x100
-+ ldrne \irqstat, [\base, #(ARM_IRQ_PEND1 - ARMCTRL_IC_BASE)]
-+ movne \irqnr, #(ARM_IRQ1_BASE + 31)
-+ @ Mask out the interrupts also present in PEND0 - see SW-5809
-+ bicne \irqstat, #((1<<7) | (1<<9) | (1<<10))
-+ bicne \irqstat, #((1<<18) | (1<<19))
-+ bne 1010f
-+
-+ tst \tmp, #0x200
-+ ldrne \irqstat, [\base, #(ARM_IRQ_PEND2 - ARMCTRL_IC_BASE)]
-+ movne \irqnr, #(ARM_IRQ2_BASE + 31)
-+ @ Mask out the interrupts also present in PEND0 - see SW-5809
-+ bicne \irqstat, #((1<<21) | (1<<22) | (1<<23) | (1<<24) | (1<<25))
-+ bicne \irqstat, #((1<<30))
-+ beq 1020f
-+
-+1010:
-+ @ For non-zero x, LSB(x) = 31 - CLZ(x^(x-1))
-+ @ N.B. CLZ is an ARM5 instruction.
-+ sub \tmp, \irqstat, #1
-+ eor \irqstat, \irqstat, \tmp
-+ clz \tmp, \irqstat
-+ sub \irqnr, \tmp
-+
-+1020: @ EQ will be set if no irqs pending
-+
-+ .endm
-+
-+ .macro test_for_ipi, irqnr, irqstat, base, tmp
-+ /* get core number */
-+ mrc p15, 0, \tmp, c0, c0, 5
-+ ubfx \tmp, \tmp, #0, #2
-+ /* get core's mailbox interrupt control */
-+ ldr \irqstat, = __io_address(ARM_LOCAL_MAILBOX0_CLR0) @ mbox_clr
-+ add \irqstat, \irqstat, \tmp, lsl #4
-+ ldr \tmp, [\irqstat]
-+ cmp \tmp, #0
-+ beq 1030f
-+ clz \tmp, \tmp
-+ rsb \irqnr, \tmp, #31
-+ mov \tmp, #1
-+ lsl \tmp, \irqnr
-+ str \tmp, [\irqstat] @ clear interrupt source
-+ dsb
-+1030: @ EQ will be set if no irqs pending
-+ .endm
---- /dev/null
-+++ b/arch/arm/mach-bcm2709/include/mach/io.h
-@@ -0,0 +1,27 @@
-+/*
-+ * arch/arm/mach-bcm2708/include/mach/io.h
-+ *
-+ * Copyright (C) 2003 ARM Limited
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
-+ */
-+#ifndef __ASM_ARM_ARCH_IO_H
-+#define __ASM_ARM_ARCH_IO_H
-+
-+#define IO_SPACE_LIMIT 0xffffffff
-+
-+#define __io(a) __typesafe_io(a)
-+
-+#endif
---- /dev/null
-+++ b/arch/arm/mach-bcm2709/include/mach/memory.h
-@@ -0,0 +1,57 @@
-+/*
-+ * arch/arm/mach-bcm2708/include/mach/memory.h
-+ *
-+ * Copyright (C) 2010 Broadcom
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
-+ */
-+#ifndef __ASM_ARCH_MEMORY_H
-+#define __ASM_ARCH_MEMORY_H
-+
-+/* Memory overview:
-+
-+ [ARMcore] <--virtual addr-->
-+ [ARMmmu] <--physical addr-->
-+ [GERTmap] <--bus add-->
-+ [VCperiph]
-+
-+*/
-+
-+/*
-+ * Physical DRAM offset.
-+ */
-+#define BCM_PLAT_PHYS_OFFSET UL(0x00000000)
-+#define VC_ARMMEM_OFFSET UL(0x00000000) /* offset in VC of ARM memory */
-+
-+#ifdef CONFIG_BCM2708_NOL2CACHE
-+ #define _REAL_BUS_OFFSET UL(0xC0000000) /* don't use L1 or L2 caches */
-+#else
-+ #define _REAL_BUS_OFFSET UL(0x40000000) /* use L2 cache */
-+#endif
-+
-+/* We're using the memory at 64M in the VideoCore for Linux - this adjustment
-+ * will provide the offset into this area as well as setting the bits that
-+ * stop the L1 and L2 cache from being used
-+ *
-+ * WARNING: this only works because the ARM is given memory at a fixed location
-+ * (ARMMEM_OFFSET)
-+ */
-+#define BUS_OFFSET (VC_ARMMEM_OFFSET + _REAL_BUS_OFFSET)
-+#define __virt_to_bus(x) ((x) + (BUS_OFFSET - PAGE_OFFSET))
-+#define __bus_to_virt(x) ((x) - (BUS_OFFSET - PAGE_OFFSET))
-+#define __pfn_to_bus(x) (__pfn_to_phys(x) + (BUS_OFFSET - BCM_PLAT_PHYS_OFFSET))
-+#define __bus_to_pfn(x) __phys_to_pfn((x) - (BUS_OFFSET - BCM_PLAT_PHYS_OFFSET))
-+
-+#endif
---- /dev/null
-+++ b/arch/arm/mach-bcm2709/include/mach/platform.h
-@@ -0,0 +1,188 @@
-+/*
-+ * arch/arm/mach-bcm2708/include/mach/platform.h
-+ *
-+ * Copyright (C) 2010 Broadcom
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
-+ */
-+
-+#ifndef _BCM2708_PLATFORM_H
-+#define _BCM2708_PLATFORM_H
-+
-+
-+/* macros to get at IO space when running virtually */
-+#define IO_ADDRESS(x) (((x) & 0x00ffffff) + (((x) >> 4) & 0x0f000000) + 0xf0000000)
-+
-+#define __io_address(n) IOMEM(IO_ADDRESS(n))
-+
-+
-+/*
-+ * SDRAM
-+ */
-+#define BCM2708_SDRAM_BASE 0x00000000
-+
-+/*
-+ * Logic expansion modules
-+ *
-+ */
-+
-+
-+/* ------------------------------------------------------------------------
-+ * BCM2708 ARMCTRL Registers
-+ * ------------------------------------------------------------------------
-+ */
-+
-+#define HW_REGISTER_RW(addr) (addr)
-+#define HW_REGISTER_RO(addr) (addr)
-+
-+/*
-+ * Definitions and addresses for the ARM CONTROL logic
-+ * This file is manually generated.
-+ */
-+
-+#define BCM2708_PERI_BASE 0x3F000000
-+#define IC0_BASE (BCM2708_PERI_BASE + 0x2000)
-+#define ST_BASE (BCM2708_PERI_BASE + 0x3000) /* System Timer */
-+#define MPHI_BASE (BCM2708_PERI_BASE + 0x6000) /* Message -based Parallel Host Interface */
-+#define DMA_BASE (BCM2708_PERI_BASE + 0x7000) /* DMA controller */
-+#define ARM_BASE (BCM2708_PERI_BASE + 0xB000) /* BCM2708 ARM control block */
-+#define PM_BASE (BCM2708_PERI_BASE + 0x100000) /* Power Management, Reset controller and Watchdog registers */
-+#define PCM_CLOCK_BASE (BCM2708_PERI_BASE + 0x101098) /* PCM Clock */
-+#define RNG_BASE (BCM2708_PERI_BASE + 0x104000) /* Hardware RNG */
-+#define GPIO_BASE (BCM2708_PERI_BASE + 0x200000) /* GPIO */
-+#define UART0_BASE (BCM2708_PERI_BASE + 0x201000) /* Uart 0 */
-+#define MMCI0_BASE (BCM2708_PERI_BASE + 0x202000) /* MMC interface */
-+#define I2S_BASE (BCM2708_PERI_BASE + 0x203000) /* I2S */
-+#define SPI0_BASE (BCM2708_PERI_BASE + 0x204000) /* SPI0 */
-+#define BSC0_BASE (BCM2708_PERI_BASE + 0x205000) /* BSC0 I2C/TWI */
-+#define UART1_BASE (BCM2708_PERI_BASE + 0x215000) /* Uart 1 */
-+#define EMMC_BASE (BCM2708_PERI_BASE + 0x300000) /* eMMC interface */
-+#define SMI_BASE (BCM2708_PERI_BASE + 0x600000) /* SMI */
-+#define BSC1_BASE (BCM2708_PERI_BASE + 0x804000) /* BSC1 I2C/TWI */
-+#define USB_BASE (BCM2708_PERI_BASE + 0x980000) /* DTC_OTG USB controller */
-+#define MCORE_BASE (BCM2708_PERI_BASE + 0x0000) /* Fake frame buffer device (actually the multicore sync block*/
-+
-+#define ARMCTRL_BASE (ARM_BASE + 0x000)
-+#define ARMCTRL_IC_BASE (ARM_BASE + 0x200) /* ARM interrupt controller */
-+#define ARMCTRL_TIMER0_1_BASE (ARM_BASE + 0x400) /* Timer 0 and 1 */
-+#define ARMCTRL_0_SBM_BASE (ARM_BASE + 0x800) /* User 0 (ARM)'s Semaphores Doorbells and Mailboxes */
-+
-+/*
-+ * Watchdog
-+ */
-+#define PM_RSTC (PM_BASE+0x1c)
-+#define PM_RSTS (PM_BASE+0x20)
-+#define PM_WDOG (PM_BASE+0x24)
-+
-+#define PM_WDOG_RESET 0000000000
-+#define PM_PASSWORD 0x5a000000
-+#define PM_WDOG_TIME_SET 0x000fffff
-+#define PM_RSTC_WRCFG_CLR 0xffffffcf
-+#define PM_RSTC_WRCFG_SET 0x00000030
-+#define PM_RSTC_WRCFG_FULL_RESET 0x00000020
-+#define PM_RSTC_RESET 0x00000102
-+
-+#define PM_RSTS_HADPOR_SET 0x00001000
-+#define PM_RSTS_HADSRH_SET 0x00000400
-+#define PM_RSTS_HADSRF_SET 0x00000200
-+#define PM_RSTS_HADSRQ_SET 0x00000100
-+#define PM_RSTS_HADWRH_SET 0x00000040
-+#define PM_RSTS_HADWRF_SET 0x00000020
-+#define PM_RSTS_HADWRQ_SET 0x00000010
-+#define PM_RSTS_HADDRH_SET 0x00000004
-+#define PM_RSTS_HADDRF_SET 0x00000002
-+#define PM_RSTS_HADDRQ_SET 0x00000001
-+
-+#define UART0_CLOCK 3000000
-+
-+#define ARM_LOCAL_BASE 0x40000000
-+#define ARM_LOCAL_CONTROL HW_REGISTER_RW(ARM_LOCAL_BASE+0x000)
-+
-+#define ARM_LOCAL_CONTROL HW_REGISTER_RW(ARM_LOCAL_BASE+0x000)
-+#define ARM_LOCAL_PRESCALER HW_REGISTER_RW(ARM_LOCAL_BASE+0x008)
-+#define ARM_LOCAL_GPU_INT_ROUTING HW_REGISTER_RW(ARM_LOCAL_BASE+0x00C)
-+#define ARM_LOCAL_PM_ROUTING_SET HW_REGISTER_RW(ARM_LOCAL_BASE+0x010)
-+#define ARM_LOCAL_PM_ROUTING_CLR HW_REGISTER_RW(ARM_LOCAL_BASE+0x014)
-+#define ARM_LOCAL_TIMER_LS HW_REGISTER_RW(ARM_LOCAL_BASE+0x01C)
-+#define ARM_LOCAL_TIMER_MS HW_REGISTER_RW(ARM_LOCAL_BASE+0x020)
-+#define ARM_LOCAL_INT_ROUTING HW_REGISTER_RW(ARM_LOCAL_BASE+0x024)
-+#define ARM_LOCAL_AXI_COUNT HW_REGISTER_RW(ARM_LOCAL_BASE+0x02C)
-+#define ARM_LOCAL_AXI_IRQ HW_REGISTER_RW(ARM_LOCAL_BASE+0x030)
-+#define ARM_LOCAL_TIMER_CONTROL HW_REGISTER_RW(ARM_LOCAL_BASE+0x034)
-+#define ARM_LOCAL_TIMER_WRITE HW_REGISTER_RW(ARM_LOCAL_BASE+0x038)
-+
-+#define ARM_LOCAL_TIMER_INT_CONTROL0 HW_REGISTER_RW(ARM_LOCAL_BASE+0x040)
-+#define ARM_LOCAL_TIMER_INT_CONTROL1 HW_REGISTER_RW(ARM_LOCAL_BASE+0x044)
-+#define ARM_LOCAL_TIMER_INT_CONTROL2 HW_REGISTER_RW(ARM_LOCAL_BASE+0x048)
-+#define ARM_LOCAL_TIMER_INT_CONTROL3 HW_REGISTER_RW(ARM_LOCAL_BASE+0x04C)
-+
-+#define ARM_LOCAL_MAILBOX_INT_CONTROL0 HW_REGISTER_RW(ARM_LOCAL_BASE+0x050)
-+#define ARM_LOCAL_MAILBOX_INT_CONTROL1 HW_REGISTER_RW(ARM_LOCAL_BASE+0x054)
-+#define ARM_LOCAL_MAILBOX_INT_CONTROL2 HW_REGISTER_RW(ARM_LOCAL_BASE+0x058)
-+#define ARM_LOCAL_MAILBOX_INT_CONTROL3 HW_REGISTER_RW(ARM_LOCAL_BASE+0x05C)
-+
-+#define ARM_LOCAL_IRQ_PENDING0 HW_REGISTER_RW(ARM_LOCAL_BASE+0x060)
-+#define ARM_LOCAL_IRQ_PENDING1 HW_REGISTER_RW(ARM_LOCAL_BASE+0x064)
-+#define ARM_LOCAL_IRQ_PENDING2 HW_REGISTER_RW(ARM_LOCAL_BASE+0x068)
-+#define ARM_LOCAL_IRQ_PENDING3 HW_REGISTER_RW(ARM_LOCAL_BASE+0x06C)
-+
-+#define ARM_LOCAL_FIQ_PENDING0 HW_REGISTER_RW(ARM_LOCAL_BASE+0x070)
-+#define ARM_LOCAL_FIQ_PENDING1 HW_REGISTER_RW(ARM_LOCAL_BASE+0x074)
-+#define ARM_LOCAL_FIQ_PENDING2 HW_REGISTER_RW(ARM_LOCAL_BASE+0x078)
-+#define ARM_LOCAL_FIQ_PENDING3 HW_REGISTER_RW(ARM_LOCAL_BASE+0x07C)
-+
-+#define ARM_LOCAL_MAILBOX0_SET0 HW_REGISTER_RW(ARM_LOCAL_BASE+0x080)
-+#define ARM_LOCAL_MAILBOX1_SET0 HW_REGISTER_RW(ARM_LOCAL_BASE+0x084)
-+#define ARM_LOCAL_MAILBOX2_SET0 HW_REGISTER_RW(ARM_LOCAL_BASE+0x088)
-+#define ARM_LOCAL_MAILBOX3_SET0 HW_REGISTER_RW(ARM_LOCAL_BASE+0x08C)
-+
-+#define ARM_LOCAL_MAILBOX0_SET1 HW_REGISTER_RW(ARM_LOCAL_BASE+0x090)
-+#define ARM_LOCAL_MAILBOX1_SET1 HW_REGISTER_RW(ARM_LOCAL_BASE+0x094)
-+#define ARM_LOCAL_MAILBOX2_SET1 HW_REGISTER_RW(ARM_LOCAL_BASE+0x098)
-+#define ARM_LOCAL_MAILBOX3_SET1 HW_REGISTER_RW(ARM_LOCAL_BASE+0x09C)
-+
-+#define ARM_LOCAL_MAILBOX0_SET2 HW_REGISTER_RW(ARM_LOCAL_BASE+0x0A0)
-+#define ARM_LOCAL_MAILBOX1_SET2 HW_REGISTER_RW(ARM_LOCAL_BASE+0x0A4)
-+#define ARM_LOCAL_MAILBOX2_SET2 HW_REGISTER_RW(ARM_LOCAL_BASE+0x0A8)
-+#define ARM_LOCAL_MAILBOX3_SET2 HW_REGISTER_RW(ARM_LOCAL_BASE+0x0AC)
-+
-+#define ARM_LOCAL_MAILBOX0_SET3 HW_REGISTER_RW(ARM_LOCAL_BASE+0x0B0)
-+#define ARM_LOCAL_MAILBOX1_SET3 HW_REGISTER_RW(ARM_LOCAL_BASE+0x0B4)
-+#define ARM_LOCAL_MAILBOX2_SET3 HW_REGISTER_RW(ARM_LOCAL_BASE+0x0B8)
-+#define ARM_LOCAL_MAILBOX3_SET3 HW_REGISTER_RW(ARM_LOCAL_BASE+0x0BC)
-+
-+#define ARM_LOCAL_MAILBOX0_CLR0 HW_REGISTER_RW(ARM_LOCAL_BASE+0x0C0)
-+#define ARM_LOCAL_MAILBOX1_CLR0 HW_REGISTER_RW(ARM_LOCAL_BASE+0x0C4)
-+#define ARM_LOCAL_MAILBOX2_CLR0 HW_REGISTER_RW(ARM_LOCAL_BASE+0x0C8)
-+#define ARM_LOCAL_MAILBOX3_CLR0 HW_REGISTER_RW(ARM_LOCAL_BASE+0x0CC)
-+
-+#define ARM_LOCAL_MAILBOX0_CLR1 HW_REGISTER_RW(ARM_LOCAL_BASE+0x0D0)
-+#define ARM_LOCAL_MAILBOX1_CLR1 HW_REGISTER_RW(ARM_LOCAL_BASE+0x0D4)
-+#define ARM_LOCAL_MAILBOX2_CLR1 HW_REGISTER_RW(ARM_LOCAL_BASE+0x0D8)
-+#define ARM_LOCAL_MAILBOX3_CLR1 HW_REGISTER_RW(ARM_LOCAL_BASE+0x0DC)
-+
-+#define ARM_LOCAL_MAILBOX0_CLR2 HW_REGISTER_RW(ARM_LOCAL_BASE+0x0E0)
-+#define ARM_LOCAL_MAILBOX1_CLR2 HW_REGISTER_RW(ARM_LOCAL_BASE+0x0E4)
-+#define ARM_LOCAL_MAILBOX2_CLR2 HW_REGISTER_RW(ARM_LOCAL_BASE+0x0E8)
-+#define ARM_LOCAL_MAILBOX3_CLR2 HW_REGISTER_RW(ARM_LOCAL_BASE+0x0EC)
-+
-+#define ARM_LOCAL_MAILBOX0_CLR3 HW_REGISTER_RW(ARM_LOCAL_BASE+0x0F0)
-+#define ARM_LOCAL_MAILBOX1_CLR3 HW_REGISTER_RW(ARM_LOCAL_BASE+0x0F4)
-+#define ARM_LOCAL_MAILBOX2_CLR3 HW_REGISTER_RW(ARM_LOCAL_BASE+0x0F8)
-+#define ARM_LOCAL_MAILBOX3_CLR3 HW_REGISTER_RW(ARM_LOCAL_BASE+0x0FC)
-+
-+#endif
-+
-+/* END */
---- /dev/null
-+++ b/arch/arm/mach-bcm2709/include/mach/system.h
-@@ -0,0 +1,37 @@
-+/*
-+ * arch/arm/mach-bcm2708/include/mach/system.h
-+ *
-+ * Copyright (C) 2010 Broadcom
-+ * Copyright (C) 2003 ARM Limited
-+ * Copyright (C) 2000 Deep Blue Solutions Ltd
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
-+ */
-+#ifndef __ASM_ARCH_SYSTEM_H
-+#define __ASM_ARCH_SYSTEM_H
-+
-+#include <linux/io.h>
-+#include <mach/platform.h>
-+
-+static inline void arch_idle(void)
-+{
-+ /*
-+ * This should do all the clock switching
-+ * and wait for interrupt tricks
-+ */
-+ cpu_do_idle();
-+}
-+
-+#endif
---- /dev/null
-+++ b/arch/arm/mach-bcm2709/include/mach/uncompress.h
-@@ -0,0 +1,84 @@
-+/*
-+ * arch/arm/mach-bcn2708/include/mach/uncompress.h
-+ *
-+ * Copyright (C) 2010 Broadcom
-+ * Copyright (C) 2003 ARM Limited
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
-+ */
-+
-+#include <linux/io.h>
-+#include <linux/amba/serial.h>
-+#include <mach/platform.h>
-+
-+#define UART_BAUD 115200
-+
-+#define BCM2708_UART_DR __io(UART0_BASE + UART01x_DR)
-+#define BCM2708_UART_FR __io(UART0_BASE + UART01x_FR)
-+#define BCM2708_UART_IBRD __io(UART0_BASE + UART011_IBRD)
-+#define BCM2708_UART_FBRD __io(UART0_BASE + UART011_FBRD)
-+#define BCM2708_UART_LCRH __io(UART0_BASE + UART011_LCRH)
-+#define BCM2708_UART_CR __io(UART0_BASE + UART011_CR)
-+
-+/*
-+ * This does not append a newline
-+ */
-+static inline void putc(int c)
-+{
-+ while (__raw_readl(BCM2708_UART_FR) & UART01x_FR_TXFF)
-+ barrier();
-+
-+ __raw_writel(c, BCM2708_UART_DR);
-+}
-+
-+static inline void flush(void)
-+{
-+ int fr;
-+
-+ do {
-+ fr = __raw_readl(BCM2708_UART_FR);
-+ barrier();
-+ } while ((fr & (UART011_FR_TXFE | UART01x_FR_BUSY)) != UART011_FR_TXFE);
-+}
-+
-+static inline void arch_decomp_setup(void)
-+{
-+ int temp, div, rem, frac;
-+
-+ temp = 16 * UART_BAUD;
-+ div = UART0_CLOCK / temp;
-+ rem = UART0_CLOCK % temp;
-+ temp = (8 * rem) / UART_BAUD;
-+ frac = (temp >> 1) + (temp & 1);
-+
-+ /* Make sure the UART is disabled before we start */
-+ __raw_writel(0, BCM2708_UART_CR);
-+
-+ /* Set the baud rate */
-+ __raw_writel(div, BCM2708_UART_IBRD);
-+ __raw_writel(frac, BCM2708_UART_FBRD);
-+
-+ /* Set the UART to 8n1, FIFO enabled */
-+ __raw_writel(UART01x_LCRH_WLEN_8 | UART01x_LCRH_FEN, BCM2708_UART_LCRH);
-+
-+ /* Enable the UART */
-+ __raw_writel(UART01x_CR_UARTEN | UART011_CR_TXE | UART011_CR_RXE,
-+ BCM2708_UART_CR);
-+}
-+
-+/*
-+ * nothing to do
-+ */
-+#define arch_decomp_wdog()
---- /dev/null
-+++ b/arch/arm/mach-bcm2709/include/mach/vc_mem.h
-@@ -0,0 +1,35 @@
-+/*****************************************************************************
-+* Copyright 2010 - 2011 Broadcom Corporation. All rights reserved.
-+*
-+* Unless you and Broadcom execute a separate written software license
-+* agreement governing use of this software, this software is licensed to you
-+* under the terms of the GNU General Public License version 2, available at
-+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
-+*
-+* Notwithstanding the above, under no circumstances may you combine this
-+* software in any way with any other Broadcom software provided under a
-+* license other than the GPL, without Broadcom's express prior written
-+* consent.
-+*****************************************************************************/
-+
-+#if !defined( VC_MEM_H )
-+#define VC_MEM_H
-+
-+#include <linux/ioctl.h>
-+
-+#define VC_MEM_IOC_MAGIC 'v'
-+
-+#define VC_MEM_IOC_MEM_PHYS_ADDR _IOR( VC_MEM_IOC_MAGIC, 0, unsigned long )
-+#define VC_MEM_IOC_MEM_SIZE _IOR( VC_MEM_IOC_MAGIC, 1, unsigned int )
-+#define VC_MEM_IOC_MEM_BASE _IOR( VC_MEM_IOC_MAGIC, 2, unsigned int )
-+#define VC_MEM_IOC_MEM_LOAD _IOR( VC_MEM_IOC_MAGIC, 3, unsigned int )
-+
-+#if defined( __KERNEL__ )
-+#define VC_MEM_TO_ARM_ADDR_MASK 0x3FFFFFFF
-+
-+extern unsigned long mm_vc_mem_phys_addr;
-+extern unsigned int mm_vc_mem_size;
-+extern int vc_mem_get_current_size( void );
-+#endif
-+
-+#endif /* VC_MEM_H */
---- /dev/null
-+++ b/arch/arm/mach-bcm2709/include/mach/vmalloc.h
-@@ -0,0 +1,20 @@
-+/*
-+ * arch/arm/mach-bcm2708/include/mach/vmalloc.h
-+ *
-+ * Copyright (C) 2010 Broadcom
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
-+ */
-+#define VMALLOC_END (0xff000000)
---- /dev/null
-+++ b/arch/arm/mach-bcm2709/vc_mem.c
-@@ -0,0 +1,431 @@
-+/*****************************************************************************
-+* Copyright 2010 - 2011 Broadcom Corporation. All rights reserved.
-+*
-+* Unless you and Broadcom execute a separate written software license
-+* agreement governing use of this software, this software is licensed to you
-+* under the terms of the GNU General Public License version 2, available at
-+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
-+*
-+* Notwithstanding the above, under no circumstances may you combine this
-+* software in any way with any other Broadcom software provided under a
-+* license other than the GPL, without Broadcom's express prior written
-+* consent.
-+*****************************************************************************/
-+
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+#include <linux/fs.h>
-+#include <linux/device.h>
-+#include <linux/cdev.h>
-+#include <linux/mm.h>
-+#include <linux/slab.h>
-+#include <linux/debugfs.h>
-+#include <asm/uaccess.h>
-+#include <linux/dma-mapping.h>
-+#include <linux/platform_data/mailbox-bcm2708.h>
-+
-+#ifdef CONFIG_ARCH_KONA
-+#include <chal/chal_ipc.h>
-+#elif defined(CONFIG_ARCH_BCM2708) || defined(CONFIG_ARCH_BCM2709)
-+#else
-+#include <csp/chal_ipc.h>
-+#endif
-+
-+#include "mach/vc_mem.h"
-+
-+#define DRIVER_NAME "vc-mem"
-+
-+// Device (/dev) related variables
-+static dev_t vc_mem_devnum = 0;
-+static struct class *vc_mem_class = NULL;
-+static struct cdev vc_mem_cdev;
-+static int vc_mem_inited = 0;
-+
-+#ifdef CONFIG_DEBUG_FS
-+static struct dentry *vc_mem_debugfs_entry;
-+#endif
-+
-+/*
-+ * Videocore memory addresses and size
-+ *
-+ * Drivers that wish to know the videocore memory addresses and sizes should
-+ * use these variables instead of the MM_IO_BASE and MM_ADDR_IO defines in
-+ * headers. This allows the other drivers to not be tied down to a a certain
-+ * address/size at compile time.
-+ *
-+ * In the future, the goal is to have the videocore memory virtual address and
-+ * size be calculated at boot time rather than at compile time. The decision of
-+ * where the videocore memory resides and its size would be in the hands of the
-+ * bootloader (and/or kernel). When that happens, the values of these variables
-+ * would be calculated and assigned in the init function.
-+ */
-+// in the 2835 VC in mapped above ARM, but ARM has full access to VC space
-+unsigned long mm_vc_mem_phys_addr = 0x00000000;
-+unsigned int mm_vc_mem_size = 0;
-+unsigned int mm_vc_mem_base = 0;
-+
-+EXPORT_SYMBOL(mm_vc_mem_phys_addr);
-+EXPORT_SYMBOL(mm_vc_mem_size);
-+EXPORT_SYMBOL(mm_vc_mem_base);
-+
-+static uint phys_addr = 0;
-+static uint mem_size = 0;
-+static uint mem_base = 0;
-+
-+
-+/****************************************************************************
-+*
-+* vc_mem_open
-+*
-+***************************************************************************/
-+
-+static int
-+vc_mem_open(struct inode *inode, struct file *file)
-+{
-+ (void) inode;
-+ (void) file;
-+
-+ pr_debug("%s: called file = 0x%p\n", __func__, file);
-+
-+ return 0;
-+}
-+
-+/****************************************************************************
-+*
-+* vc_mem_release
-+*
-+***************************************************************************/
-+
-+static int
-+vc_mem_release(struct inode *inode, struct file *file)
-+{
-+ (void) inode;
-+ (void) file;
-+
-+ pr_debug("%s: called file = 0x%p\n", __func__, file);
-+
-+ return 0;
-+}
-+
-+/****************************************************************************
-+*
-+* vc_mem_get_size
-+*
-+***************************************************************************/
-+
-+static void
-+vc_mem_get_size(void)
-+{
-+}
-+
-+/****************************************************************************
-+*
-+* vc_mem_get_base
-+*
-+***************************************************************************/
-+
-+static void
-+vc_mem_get_base(void)
-+{
-+}
-+
-+/****************************************************************************
-+*
-+* vc_mem_get_current_size
-+*
-+***************************************************************************/
-+
-+int
-+vc_mem_get_current_size(void)
-+{
-+ return mm_vc_mem_size;
-+}
-+
-+EXPORT_SYMBOL_GPL(vc_mem_get_current_size);
-+
-+/****************************************************************************
-+*
-+* vc_mem_ioctl
-+*
-+***************************************************************************/
-+
-+static long
-+vc_mem_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
-+{
-+ int rc = 0;
-+
-+ (void) cmd;
-+ (void) arg;
-+
-+ pr_debug("%s: called file = 0x%p\n", __func__, file);
-+
-+ switch (cmd) {
-+ case VC_MEM_IOC_MEM_PHYS_ADDR:
-+ {
-+ pr_debug("%s: VC_MEM_IOC_MEM_PHYS_ADDR=0x%p\n",
-+ __func__, (void *) mm_vc_mem_phys_addr);
-+
-+ if (copy_to_user((void *) arg, &mm_vc_mem_phys_addr,
-+ sizeof (mm_vc_mem_phys_addr)) != 0) {
-+ rc = -EFAULT;
-+ }
-+ break;
-+ }
-+ case VC_MEM_IOC_MEM_SIZE:
-+ {
-+ // Get the videocore memory size first
-+ vc_mem_get_size();
-+
-+ pr_debug("%s: VC_MEM_IOC_MEM_SIZE=%u\n", __func__,
-+ mm_vc_mem_size);
-+
-+ if (copy_to_user((void *) arg, &mm_vc_mem_size,
-+ sizeof (mm_vc_mem_size)) != 0) {
-+ rc = -EFAULT;
-+ }
-+ break;
-+ }
-+ case VC_MEM_IOC_MEM_BASE:
-+ {
-+ // Get the videocore memory base
-+ vc_mem_get_base();
-+
-+ pr_debug("%s: VC_MEM_IOC_MEM_BASE=%u\n", __func__,
-+ mm_vc_mem_base);
-+
-+ if (copy_to_user((void *) arg, &mm_vc_mem_base,
-+ sizeof (mm_vc_mem_base)) != 0) {
-+ rc = -EFAULT;
-+ }
-+ break;
-+ }
-+ case VC_MEM_IOC_MEM_LOAD:
-+ {
-+ // Get the videocore memory base
-+ vc_mem_get_base();
-+
-+ pr_debug("%s: VC_MEM_IOC_MEM_LOAD=%u\n", __func__,
-+ mm_vc_mem_base);
-+
-+ if (copy_to_user((void *) arg, &mm_vc_mem_base,
-+ sizeof (mm_vc_mem_base)) != 0) {
-+ rc = -EFAULT;
-+ }
-+ break;
-+ }
-+ default:
-+ {
-+ return -ENOTTY;
-+ }
-+ }
-+ pr_debug("%s: file = 0x%p returning %d\n", __func__, file, rc);
-+
-+ return rc;
-+}
-+
-+/****************************************************************************
-+*
-+* vc_mem_mmap
-+*
-+***************************************************************************/
-+
-+static int
-+vc_mem_mmap(struct file *filp, struct vm_area_struct *vma)
-+{
-+ int rc = 0;
-+ unsigned long length = vma->vm_end - vma->vm_start;
-+ unsigned long offset = vma->vm_pgoff << PAGE_SHIFT;
-+
-+ pr_debug("%s: vm_start = 0x%08lx vm_end = 0x%08lx vm_pgoff = 0x%08lx\n",
-+ __func__, (long) vma->vm_start, (long) vma->vm_end,
-+ (long) vma->vm_pgoff);
-+
-+ if (offset + length > mm_vc_mem_size) {
-+ pr_err("%s: length %ld is too big\n", __func__, length);
-+ return -EINVAL;
-+ }
-+ // Do not cache the memory map
-+ vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
-+
-+ rc = remap_pfn_range(vma, vma->vm_start,
-+ (mm_vc_mem_phys_addr >> PAGE_SHIFT) +
-+ vma->vm_pgoff, length, vma->vm_page_prot);
-+ if (rc != 0) {
-+ pr_err("%s: remap_pfn_range failed (rc=%d)\n", __func__, rc);
-+ }
-+
-+ return rc;
-+}
-+
-+/****************************************************************************
-+*
-+* File Operations for the driver.
-+*
-+***************************************************************************/
-+
-+static const struct file_operations vc_mem_fops = {
-+ .owner = THIS_MODULE,
-+ .open = vc_mem_open,
-+ .release = vc_mem_release,
-+ .unlocked_ioctl = vc_mem_ioctl,
-+ .mmap = vc_mem_mmap,
-+};
-+
-+#ifdef CONFIG_DEBUG_FS
-+static void vc_mem_debugfs_deinit(void)
-+{
-+ debugfs_remove_recursive(vc_mem_debugfs_entry);
-+ vc_mem_debugfs_entry = NULL;
-+}
-+
-+
-+static int vc_mem_debugfs_init(
-+ struct device *dev)
-+{
-+ vc_mem_debugfs_entry = debugfs_create_dir(DRIVER_NAME, NULL);
-+ if (!vc_mem_debugfs_entry) {
-+ dev_warn(dev, "could not create debugfs entry\n");
-+ return -EFAULT;
-+ }
-+
-+ if (!debugfs_create_x32("vc_mem_phys_addr",
-+ 0444,
-+ vc_mem_debugfs_entry,
-+ (u32 *)&mm_vc_mem_phys_addr)) {
-+ dev_warn(dev, "%s:could not create vc_mem_phys entry\n",
-+ __func__);
-+ goto fail;
-+ }
-+
-+ if (!debugfs_create_x32("vc_mem_size",
-+ 0444,
-+ vc_mem_debugfs_entry,
-+ (u32 *)&mm_vc_mem_size)) {
-+ dev_warn(dev, "%s:could not create vc_mem_size entry\n",
-+ __func__);
-+ goto fail;
-+ }
-+
-+ if (!debugfs_create_x32("vc_mem_base",
-+ 0444,
-+ vc_mem_debugfs_entry,
-+ (u32 *)&mm_vc_mem_base)) {
-+ dev_warn(dev, "%s:could not create vc_mem_base entry\n",
-+ __func__);
-+ goto fail;
-+ }
-+
-+ return 0;
-+
-+fail:
-+ vc_mem_debugfs_deinit();
-+ return -EFAULT;
-+}
-+
-+#endif /* CONFIG_DEBUG_FS */
-+
-+
-+/****************************************************************************
-+*
-+* vc_mem_init
-+*
-+***************************************************************************/
-+
-+static int __init
-+vc_mem_init(void)
-+{
-+ int rc = -EFAULT;
-+ struct device *dev;
-+
-+ pr_debug("%s: called\n", __func__);
-+
-+ mm_vc_mem_phys_addr = phys_addr;
-+ mm_vc_mem_size = mem_size;
-+ mm_vc_mem_base = mem_base;
-+
-+ vc_mem_get_size();
-+
-+ pr_info("vc-mem: phys_addr:0x%08lx mem_base=0x%08x mem_size:0x%08x(%u MiB)\n",
-+ mm_vc_mem_phys_addr, mm_vc_mem_base, mm_vc_mem_size, mm_vc_mem_size / (1024 * 1024));
-+
-+ if ((rc = alloc_chrdev_region(&vc_mem_devnum, 0, 1, DRIVER_NAME)) < 0) {
-+ pr_err("%s: alloc_chrdev_region failed (rc=%d)\n",
-+ __func__, rc);
-+ goto out_err;
-+ }
-+
-+ cdev_init(&vc_mem_cdev, &vc_mem_fops);
-+ if ((rc = cdev_add(&vc_mem_cdev, vc_mem_devnum, 1)) != 0) {
-+ pr_err("%s: cdev_add failed (rc=%d)\n", __func__, rc);
-+ goto out_unregister;
-+ }
-+
-+ vc_mem_class = class_create(THIS_MODULE, DRIVER_NAME);
-+ if (IS_ERR(vc_mem_class)) {
-+ rc = PTR_ERR(vc_mem_class);
-+ pr_err("%s: class_create failed (rc=%d)\n", __func__, rc);
-+ goto out_cdev_del;
-+ }
-+
-+ dev = device_create(vc_mem_class, NULL, vc_mem_devnum, NULL,
-+ DRIVER_NAME);
-+ if (IS_ERR(dev)) {
-+ rc = PTR_ERR(dev);
-+ pr_err("%s: device_create failed (rc=%d)\n", __func__, rc);
-+ goto out_class_destroy;
-+ }
-+
-+#ifdef CONFIG_DEBUG_FS
-+ /* don't fail if the debug entries cannot be created */
-+ vc_mem_debugfs_init(dev);
-+#endif
-+
-+ vc_mem_inited = 1;
-+ return 0;
-+
-+ device_destroy(vc_mem_class, vc_mem_devnum);
-+
-+ out_class_destroy:
-+ class_destroy(vc_mem_class);
-+ vc_mem_class = NULL;
-+
-+ out_cdev_del:
-+ cdev_del(&vc_mem_cdev);
-+
-+ out_unregister:
-+ unregister_chrdev_region(vc_mem_devnum, 1);
-+
-+ out_err:
-+ return -1;
-+}
-+
-+/****************************************************************************
-+*
-+* vc_mem_exit
-+*
-+***************************************************************************/
-+
-+static void __exit
-+vc_mem_exit(void)
-+{
-+ pr_debug("%s: called\n", __func__);
-+
-+ if (vc_mem_inited) {
-+#if CONFIG_DEBUG_FS
-+ vc_mem_debugfs_deinit();
-+#endif
-+ device_destroy(vc_mem_class, vc_mem_devnum);
-+ class_destroy(vc_mem_class);
-+ cdev_del(&vc_mem_cdev);
-+ unregister_chrdev_region(vc_mem_devnum, 1);
-+ }
-+}
-+
-+module_init(vc_mem_init);
-+module_exit(vc_mem_exit);
-+MODULE_LICENSE("GPL");
-+MODULE_AUTHOR("Broadcom Corporation");
-+
-+module_param(phys_addr, uint, 0644);
-+module_param(mem_size, uint, 0644);
-+module_param(mem_base, uint, 0644);
---- a/arch/arm/mm/Kconfig
-+++ b/arch/arm/mm/Kconfig
-@@ -358,7 +358,7 @@ config CPU_PJ4B
-
- # ARMv6
- config CPU_V6
-- bool "Support ARM V6 processor" if (!ARCH_MULTIPLATFORM || ARCH_MULTI_V6) && (ARCH_INTEGRATOR || MACH_REALVIEW_EB || MACH_REALVIEW_PBX)
-+ bool "Support ARM V6 processor" if (!ARCH_MULTIPLATFORM || ARCH_MULTI_V6) && (ARCH_INTEGRATOR || MACH_REALVIEW_EB || MACH_REALVIEW_PBX || MACH_BCM2708)
- select CPU_32v6
- select CPU_ABRT_EV6
- select CPU_CACHE_V6
---- a/arch/arm/mm/proc-v6.S
-+++ b/arch/arm/mm/proc-v6.S
-@@ -73,10 +73,19 @@ ENDPROC(cpu_v6_reset)
- *
- * IRQs are already disabled.
- */
-+
-+/* See jira SW-5991 for details of this workaround */
- ENTRY(cpu_v6_do_idle)
-- mov r1, #0
-- mcr p15, 0, r1, c7, c10, 4 @ DWB - WFI may enter a low-power mode
-- mcr p15, 0, r1, c7, c0, 4 @ wait for interrupt
-+ .align 5
-+ mov r1, #2
-+1: subs r1, #1
-+ nop
-+ mcreq p15, 0, r1, c7, c10, 4 @ DWB - WFI may enter a low-power mode
-+ mcreq p15, 0, r1, c7, c0, 4 @ wait for interrupt
-+ nop
-+ nop
-+ nop
-+ bne 1b
- ret lr
-
- ENTRY(cpu_v6_dcache_clean_area)
---- a/arch/arm/mm/proc-v7.S
-+++ b/arch/arm/mm/proc-v7.S
-@@ -480,6 +480,7 @@ __errata_finish:
- orr r0, r0, r6 @ set them
- THUMB( orr r0, r0, #1 << 30 ) @ Thumb exceptions
- ret lr @ return to head.S:__ret
-+ .space 256
- ENDPROC(__v7_setup)
-
- .align 2
---- a/arch/arm/tools/mach-types
-+++ b/arch/arm/tools/mach-types
-@@ -522,6 +522,8 @@ torbreck MACH_TORBRECK TORBRECK 3090
- prima2_evb MACH_PRIMA2_EVB PRIMA2_EVB 3103
- paz00 MACH_PAZ00 PAZ00 3128
- acmenetusfoxg20 MACH_ACMENETUSFOXG20 ACMENETUSFOXG20 3129
-+bcm2708 MACH_BCM2708 BCM2708 3138
-+bcm2709 MACH_BCM2709 BCM2709 3139
- ag5evm MACH_AG5EVM AG5EVM 3189
- ics_if_voip MACH_ICS_IF_VOIP ICS_IF_VOIP 3206
- wlf_cragg_6410 MACH_WLF_CRAGG_6410 WLF_CRAGG_6410 3207
---- a/drivers/clocksource/Makefile
-+++ b/drivers/clocksource/Makefile
-@@ -19,7 +19,7 @@ obj-$(CONFIG_CLKSRC_NOMADIK_MTU) += noma
- obj-$(CONFIG_CLKSRC_DBX500_PRCMU) += clksrc-dbx500-prcmu.o
- obj-$(CONFIG_ARMADA_370_XP_TIMER) += time-armada-370-xp.o
- obj-$(CONFIG_ORION_TIMER) += time-orion.o
--obj-$(CONFIG_ARCH_BCM2835) += bcm2835_timer.o
-+obj-$(CONFIG_ARCH_BCM2835)$(CONFIG_ARCH_BCM2708) += bcm2835_timer.o
- obj-$(CONFIG_ARCH_CLPS711X) += clps711x-timer.o
- obj-$(CONFIG_ARCH_ATLAS7) += timer-atlas7.o
- obj-$(CONFIG_ARCH_MOXART) += moxart_timer.o
---- a/drivers/irqchip/Makefile
-+++ b/drivers/irqchip/Makefile
-@@ -2,6 +2,9 @@ obj-$(CONFIG_IRQCHIP) += irqchip.o
-
- obj-$(CONFIG_ARCH_BCM2835) += irq-bcm2835.o
- obj-$(CONFIG_ARCH_BCM2835) += irq-bcm2836.o
-+obj-$(CONFIG_ARCH_BCM2708) += irq-bcm2835.o
-+obj-$(CONFIG_ARCH_BCM2709) += irq-bcm2835.o
-+obj-$(CONFIG_ARCH_BCM2709) += irq-bcm2836.o
- obj-$(CONFIG_ARCH_EXYNOS) += exynos-combiner.o
- obj-$(CONFIG_ARCH_HIP04) += irq-hip04.o
- obj-$(CONFIG_ARCH_MMP) += irq-mmp.o
---- a/include/linux/mmc/host.h
-+++ b/include/linux/mmc/host.h
-@@ -289,6 +289,7 @@ struct mmc_host {
- #define MMC_CAP2_HSX00_1_2V (MMC_CAP2_HS200_1_2V_SDR | MMC_CAP2_HS400_1_2V)
- #define MMC_CAP2_SDIO_IRQ_NOTHREAD (1 << 17)
- #define MMC_CAP2_NO_WRITE_PROTECT (1 << 18) /* No physical write protect pin, assume that card is always read-write */
-+#define MMC_CAP2_FORCE_MULTIBLOCK (1 << 31) /* Always use multiblock transfers */
-
- mmc_pm_flag_t pm_caps; /* supported pm features */
-
diff --git a/target/linux/brcm2708/patches-4.4/0028-squash-include-ARCH_BCM2708-ARCH_BCM2709.patch b/target/linux/brcm2708/patches-4.4/0028-squash-include-ARCH_BCM2708-ARCH_BCM2709.patch
deleted file mode 100644
index 8010e7d..0000000
--- a/target/linux/brcm2708/patches-4.4/0028-squash-include-ARCH_BCM2708-ARCH_BCM2709.patch
+++ /dev/null
@@ -1,138 +0,0 @@
-From fcc9c391c9244922fc3b955d7bf08c6db8b54a9c Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Wed, 11 Nov 2015 21:01:15 +0000
-Subject: [PATCH] squash: include ARCH_BCM2708 / ARCH_BCM2709
-
----
- drivers/char/hw_random/Kconfig | 2 +-
- drivers/mailbox/Kconfig | 2 +-
- drivers/mailbox/bcm2835-mailbox.c | 18 ++++++++++++++++--
- drivers/pinctrl/Makefile | 1 +
- drivers/pwm/Kconfig | 2 +-
- drivers/spi/Kconfig | 2 +-
- drivers/watchdog/Kconfig | 2 +-
- sound/soc/bcm/Kconfig | 2 +-
- 8 files changed, 23 insertions(+), 8 deletions(-)
-
---- a/drivers/char/hw_random/Kconfig
-+++ b/drivers/char/hw_random/Kconfig
-@@ -90,7 +90,7 @@ config HW_RANDOM_BCM63XX
-
- config HW_RANDOM_BCM2835
- tristate "Broadcom BCM2835 Random Number Generator support"
-- depends on ARCH_BCM2835
-+ depends on ARCH_BCM2835 || ARCH_BCM2708 || ARCH_BCM2709
- default HW_RANDOM
- ---help---
- This driver provides kernel-side support for the Random Number
---- a/drivers/mailbox/Kconfig
-+++ b/drivers/mailbox/Kconfig
-@@ -65,7 +65,7 @@ config ALTERA_MBOX
-
- config BCM2835_MBOX
- tristate "BCM2835 Mailbox"
-- depends on ARCH_BCM2835
-+ depends on ARCH_BCM2835 || ARCH_BCM2708 || ARCH_BCM2709
- help
- An implementation of the BCM2385 Mailbox. It is used to invoke
- the services of the Videocore. Say Y here if you want to use the
---- a/drivers/mailbox/bcm2835-mailbox.c
-+++ b/drivers/mailbox/bcm2835-mailbox.c
-@@ -51,12 +51,15 @@
- #define MAIL1_WRT (ARM_0_MAIL1 + 0x00)
- #define MAIL1_STA (ARM_0_MAIL1 + 0x18)
-
-+/* On ARCH_BCM270x these come through <linux/interrupt.h> (arm_control.h ) */
-+#ifndef ARM_MS_FULL
- /* Status register: FIFO state. */
- #define ARM_MS_FULL BIT(31)
- #define ARM_MS_EMPTY BIT(30)
-
- /* Configuration register: Enable interrupts. */
- #define ARM_MC_IHAVEDATAIRQEN BIT(0)
-+#endif
-
- struct bcm2835_mbox {
- void __iomem *regs;
-@@ -151,7 +154,7 @@ static int bcm2835_mbox_probe(struct pla
- return -ENOMEM;
- spin_lock_init(&mbox->lock);
-
-- ret = devm_request_irq(dev, irq_of_parse_and_map(dev->of_node, 0),
-+ ret = devm_request_irq(dev, platform_get_irq(pdev, 0),
- bcm2835_mbox_irq, 0, dev_name(dev), mbox);
- if (ret) {
- dev_err(dev, "Failed to register a mailbox IRQ handler: %d\n",
-@@ -209,7 +212,18 @@ static struct platform_driver bcm2835_mb
- .probe = bcm2835_mbox_probe,
- .remove = bcm2835_mbox_remove,
- };
--module_platform_driver(bcm2835_mbox_driver);
-+
-+static int __init bcm2835_mbox_init(void)
-+{
-+ return platform_driver_register(&bcm2835_mbox_driver);
-+}
-+arch_initcall(bcm2835_mbox_init);
-+
-+static void __init bcm2835_mbox_exit(void)
-+{
-+ platform_driver_unregister(&bcm2835_mbox_driver);
-+}
-+module_exit(bcm2835_mbox_exit);
-
- MODULE_AUTHOR("Lubomir Rintel <lkundrak at v3.sk>");
- MODULE_DESCRIPTION("BCM2835 mailbox IPC driver");
---- a/drivers/pinctrl/Makefile
-+++ b/drivers/pinctrl/Makefile
-@@ -40,6 +40,7 @@ obj-$(CONFIG_PINCTRL_TB10X) += pinctrl-t
- obj-$(CONFIG_PINCTRL_ST) += pinctrl-st.o
- obj-$(CONFIG_PINCTRL_ZYNQ) += pinctrl-zynq.o
-
-+obj-$(CONFIG_ARCH_BCM2708)$(CONFIG_ARCH_BCM2709) += bcm/
- obj-$(CONFIG_ARCH_BCM) += bcm/
- obj-$(CONFIG_ARCH_BERLIN) += berlin/
- obj-y += freescale/
---- a/drivers/pwm/Kconfig
-+++ b/drivers/pwm/Kconfig
-@@ -85,7 +85,7 @@ config PWM_BCM_KONA
-
- config PWM_BCM2835
- tristate "BCM2835 PWM support"
-- depends on ARCH_BCM2835
-+ depends on ARCH_BCM2835 || ARCH_BCM2708 || ARCH_BCM2709
- help
- PWM framework driver for BCM2835 controller (Raspberry Pi)
-
---- a/drivers/spi/Kconfig
-+++ b/drivers/spi/Kconfig
-@@ -78,7 +78,7 @@ config SPI_ATMEL
- config SPI_BCM2835
- tristate "BCM2835 SPI controller"
- depends on GPIOLIB
-- depends on ARCH_BCM2835 || COMPILE_TEST
-+ depends on ARCH_BCM2835 || ARCH_BCM2708 || ARCH_BCM2709 || COMPILE_TEST
- depends on GPIOLIB
- help
- This selects a driver for the Broadcom BCM2835 SPI master.
---- a/drivers/watchdog/Kconfig
-+++ b/drivers/watchdog/Kconfig
-@@ -1282,7 +1282,7 @@ config BCM63XX_WDT
-
- config BCM2835_WDT
- tristate "Broadcom BCM2835 hardware watchdog"
-- depends on ARCH_BCM2835
-+ depends on ARCH_BCM2835 || ARCH_BCM2708 || ARCH_BCM2709
- select WATCHDOG_CORE
- help
- Watchdog driver for the built in watchdog hardware in Broadcom
---- a/sound/soc/bcm/Kconfig
-+++ b/sound/soc/bcm/Kconfig
-@@ -1,6 +1,6 @@
- config SND_BCM2835_SOC_I2S
- tristate "SoC Audio support for the Broadcom BCM2835 I2S module"
-- depends on ARCH_BCM2835 || COMPILE_TEST
-+ depends on ARCH_BCM2835 || MACH_BCM2708 || MACH_BCM2709 || COMPILE_TEST
- select SND_SOC_GENERIC_DMAENGINE_PCM
- select REGMAP_MMIO
- help
diff --git a/target/linux/brcm2708/patches-4.4/0029-Add-dwc_otg-driver.patch b/target/linux/brcm2708/patches-4.4/0029-Add-dwc_otg-driver.patch
deleted file mode 100644
index 7f9ab7c..0000000
--- a/target/linux/brcm2708/patches-4.4/0029-Add-dwc_otg-driver.patch
+++ /dev/null
@@ -1,60780 +0,0 @@
-From 58b2dd98335c7719f4d304a7401a5c2349a2f4cc Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Wed, 1 May 2013 19:46:17 +0100
-Subject: [PATCH] Add dwc_otg driver
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Signed-off-by: popcornmix <popcornmix at gmail.com>
-
-usb: dwc: fix lockdep false positive
-
-Signed-off-by: Kari Suvanto <karis79 at gmail.com>
-
-usb: dwc: fix inconsistent lock state
-
-Signed-off-by: Kari Suvanto <karis79 at gmail.com>
-
-Add FIQ patch to dwc_otg driver. Enable with dwc_otg.fiq_fix_enable=1. Should give about 10% more ARM performance.
-Thanks to Gordon and Costas
-
-Avoid dynamic memory allocation for channel lock in USB driver. Thanks ddv2005.
-
-Add NAK holdoff scheme. Enabled by default, disable with dwc_otg.nak_holdoff_enable=0. Thanks gsh
-
-Make sure we wait for the reset to finish
-
-dwc_otg: fix bug in dwc_otg_hcd.c resulting in silent kernel
- memory corruption, escalating to OOPS under high USB load.
-
-dwc_otg: Fix unsafe access of QTD during URB enqueue
-
-In dwc_otg_hcd_urb_enqueue during qtd creation, it was possible that the
-transaction could complete almost immediately after the qtd was assigned
-to a host channel during URB enqueue, which meant the qtd pointer was no
-longer valid having been completed and removed. Usually, this resulted in
-an OOPS during URB submission. By predetermining whether transactions
-need to be queued or not, this unsafe pointer access is avoided.
-
-This bug was only evident on the Pi model A where a device was attached
-that had no periodic endpoints (e.g. USB pendrive or some wlan devices).
-
-dwc_otg: Fix incorrect URB allocation error handling
-
-If the memory allocation for a dwc_otg_urb failed, the kernel would OOPS
-because for some reason a member of the *unallocated* struct was set to
-zero. Error handling changed to fail correctly.
-
-dwc_otg: fix potential use-after-free case in interrupt handler
-
-If a transaction had previously aborted, certain interrupts are
-enabled to track error counts and reset where necessary. On IN
-endpoints the host generates an ACK interrupt near-simultaneously
-with completion of transfer. In the case where this transfer had
-previously had an error, this results in a use-after-free on
-the QTD memory space with a 1-byte length being overwritten to
-0x00.
-
-dwc_otg: add handling of SPLIT transaction data toggle errors
-
-Previously a data toggle error on packets from a USB1.1 device behind
-a TT would result in the Pi locking up as the driver never handled
-the associated interrupt. Patch adds basic retry mechanism and
-interrupt acknowledgement to cater for either a chance toggle error or
-for devices that have a broken initial toggle state (FT8U232/FT232BM).
-
-dwc_otg: implement tasklet for returning URBs to usbcore hcd layer
-
-The dwc_otg driver interrupt handler for transfer completion will spend
-a very long time with interrupts disabled when a URB is completed -
-this is because usb_hcd_giveback_urb is called from within the handler
-which for a USB device driver with complicated processing (e.g. webcam)
-will take an exorbitant amount of time to complete. This results in
-missed completion interrupts for other USB packets which lead to them
-being dropped due to microframe overruns.
-
-This patch splits returning the URB to the usb hcd layer into a
-high-priority tasklet. This will have most benefit for isochronous IN
-transfers but will also have incidental benefit where multiple periodic
-devices are active at once.
-
-dwc_otg: fix NAK holdoff and allow on split transactions only
-
-This corrects a bug where if a single active non-periodic endpoint
-had at least one transaction in its qh, on frnum == MAX_FRNUM the qh
-would get skipped and never get queued again. This would result in
-a silent device until error detection (automatic or otherwise) would
-either reset the device or flush and requeue the URBs.
-
-Additionally the NAK holdoff was enabled for all transactions - this
-would potentially stall a HS endpoint for 1ms if a previous error state
-enabled this interrupt and the next response was a NAK. Fix so that
-only split transactions get held off.
-
-dwc_otg: Call usb_hcd_unlink_urb_from_ep with lock held in completion handler
-
-usb_hcd_unlink_urb_from_ep must be called with the HCD lock held. Calling it
-asynchronously in the tasklet was not safe (regression in
-c4564d4a1a0a9b10d4419e48239f5d99e88d2667).
-
-This change unlinks it from the endpoint prior to queueing it for handling in
-the tasklet, and also adds a check to ensure the urb is OK to be unlinked
-before doing so.
-
-NULL pointer dereference kernel oopses had been observed in usb_hcd_giveback_urb
-when a USB device was unplugged/replugged during data transfer. This effect
-was reproduced using automated USB port power control, hundreds of replug
-events were performed during active transfers to confirm that the problem was
-eliminated.
-
-USB fix using a FIQ to implement split transactions
-
-This commit adds a FIQ implementaion that schedules
-the split transactions using a FIQ so we don't get
-held off by the interrupt latency of Linux
-
-dwc_otg: fix device attributes and avoid kernel warnings on boot
-
-dcw_otg: avoid logging function that can cause panics
-
-See: https://github.com/raspberrypi/firmware/issues/21
-Thanks to cleverca22 for fix
-
-dwc_otg: mask correct interrupts after transaction error recovery
-
-The dwc_otg driver will unmask certain interrupts on a transaction
-that previously halted in the error state in order to reset the
-QTD error count. The various fine-grained interrupt handlers do not
-consider that other interrupts besides themselves were unmasked.
-
-By disabling the two other interrupts only ever enabled in DMA mode
-for this purpose, we can avoid unnecessary function calls in the
-IRQ handler. This will also prevent an unneccesary FIQ interrupt
-from being generated if the FIQ is enabled.
-
-dwc_otg: fiq: prevent FIQ thrash and incorrect state passing to IRQ
-
-In the case of a transaction to a device that had previously aborted
-due to an error, several interrupts are enabled to reset the error
-count when a device responds. This has the side-effect of making the
-FIQ thrash because the hardware will generate multiple instances of
-a NAK on an IN bulk/interrupt endpoint and multiple instances of ACK
-on an OUT bulk/interrupt endpoint. Make the FIQ mask and clear the
-associated interrupts.
-
-Additionally, on non-split transactions make sure that only unmasked
-interrupts are cleared. This caused a hard-to-trigger but serious
-race condition when you had the combination of an endpoint awaiting
-error recovery and a transaction completed on an endpoint - due to
-the sequencing and timing of interrupts generated by the dwc_otg core,
-it was possible to confuse the IRQ handler.
-
-Fix function tracing
-
-dwc_otg: whitespace cleanup in dwc_otg_urb_enqueue
-
-dwc_otg: prevent OOPSes during device disconnects
-
-The dwc_otg_urb_enqueue function is thread-unsafe. In particular the
-access of urb->hcpriv, usb_hcd_link_urb_to_ep, dwc_otg_urb->qtd and
-friends does not occur within a critical section and so if a device
-was unplugged during activity there was a high chance that the
-usbcore hub_thread would try to disable the endpoint with partially-
-formed entries in the URB queue. This would result in BUG() or null
-pointer dereferences.
-
-Fix so that access of urb->hcpriv, enqueuing to the hardware and
-adding to usbcore endpoint URB lists is contained within a single
-critical section.
-
-dwc_otg: prevent BUG() in TT allocation if hub address is > 16
-
-A fixed-size array is used to track TT allocation. This was
-previously set to 16 which caused a crash because
-dwc_otg_hcd_allocate_port would read past the end of the array.
-
-This was hit if a hub was plugged in which enumerated as addr > 16,
-due to previous device resets or unplugs.
-
-Also add #ifdef FIQ_DEBUG around hcd->hub_port_alloc[], which grows
-to a large size if 128 hub addresses are supported. This field is
-for debug only for tracking which frame an allocate happened in.
-
-dwc_otg: make channel halts with unknown state less damaging
-
-If the IRQ received a channel halt interrupt through the FIQ
-with no other bits set, the IRQ would not release the host
-channel and never complete the URB.
-
-Add catchall handling to treat as a transaction error and retry.
-
-dwc_otg: fiq_split: use TTs with more granularity
-
-This fixes certain issues with split transaction scheduling.
-
-- Isochronous multi-packet OUT transactions now hog the TT until
- they are completed - this prevents hubs aborting transactions
- if they get a periodic start-split out-of-order
-- Don't perform TT allocation on non-periodic endpoints - this
- allows simultaneous use of the TT's bulk/control and periodic
- transaction buffers
-
-This commit will mainly affect USB audio playback.
-
-dwc_otg: fix potential sleep while atomic during urb enqueue
-
-Fixes a regression introduced with eb1b482a. Kmalloc called from
-dwc_otg_hcd_qtd_add / dwc_otg_hcd_qtd_create did not always have
-the GPF_ATOMIC flag set. Force this flag when inside the larger
-critical section.
-
-dwc_otg: make fiq_split_enable imply fiq_fix_enable
-
-Failing to set up the FIQ correctly would result in
-"IRQ 32: nobody cared" errors in dmesg.
-
-dwc_otg: prevent crashes on host port disconnects
-
-Fix several issues resulting in crashes or inconsistent state
-if a Model A root port was disconnected.
-
-- Clean up queue heads properly in kill_urbs_in_qh_list by
- removing the empty QHs from the schedule lists
-- Set the halt status properly to prevent IRQ handlers from
- using freed memory
-- Add fiq_split related cleanup for saved registers
-- Make microframe scheduling reclaim host channels if
- active during a disconnect
-- Abort URBs with -ESHUTDOWN status response, informing
- device drivers so they respond in a more correct fashion
- and don't try to resubmit URBs
-- Prevent IRQ handlers from attempting to handle channel
- interrupts if the associated URB was dequeued (and the
- driver state was cleared)
-
-dwc_otg: prevent leaking URBs during enqueue
-
-A dwc_otg_urb would get leaked if the HCD enqueue function
-failed for any reason. Free the URB at the appropriate points.
-
-dwc_otg: Enable NAK holdoff for control split transactions
-
-Certain low-speed devices take a very long time to complete a
-data or status stage of a control transaction, producing NAK
-responses until they complete internal processing - the USB2.0
-spec limit is up to 500mS. This causes the same type of interrupt
-storm as seen with USB-serial dongles prior to c8edb238.
-
-In certain circumstances, usually while booting, this interrupt
-storm could cause SD card timeouts.
-
-dwc_otg: Fix for occasional lockup on boot when doing a USB reset
-
-dwc_otg: Don't issue traffic to LS devices in FS mode
-
-Issuing low-speed packets when the root port is in full-speed mode
-causes the root port to stop responding. Explicitly fail when
-enqueuing URBs to a LS endpoint on a FS bus.
-
-Fix ARM architecture issue with local_irq_restore()
-
-If local_fiq_enable() is called before a local_irq_restore(flags) where
-the flags variable has the F bit set, the FIQ will be erroneously disabled.
-
-Fixup arch_local_irq_restore to avoid trampling the F bit in CPSR.
-
-Also fix some of the hacks previously implemented for previous dwc_otg
-incarnations.
-
-dwc_otg: fiq_fsm: Base commit for driver rewrite
-
-This commit removes the previous FIQ fixes entirely and adds fiq_fsm.
-
-This rewrite features much more complete support for split transactions
-and takes into account several OTG hardware bugs. High-speed
-isochronous transactions are also capable of being performed by fiq_fsm.
-
-All driver options have been removed and replaced with:
- - dwc_otg.fiq_enable (bool)
- - dwc_otg.fiq_fsm_enable (bool)
- - dwc_otg.fiq_fsm_mask (bitmask)
- - dwc_otg.nak_holdoff (unsigned int)
-
-Defaults are specified such that fiq_fsm behaves similarly to the
-previously implemented FIQ fixes.
-
-fiq_fsm: Push error recovery into the FIQ when fiq_fsm is used
-
-If the transfer associated with a QTD failed due to a bus error, the HCD
-would retry the transfer up to 3 times (implementing the USB2.0
-three-strikes retry in software).
-
-Due to the masking mechanism used by fiq_fsm, it is only possible to pass
-a single interrupt through to the HCD per-transfer.
-
-In this instance host channels would fall off the radar because the error
-reset would function, but the subsequent channel halt would be lost.
-
-Push the error count reset into the FIQ handler.
-
-fiq_fsm: Implement timeout mechanism
-
-For full-speed endpoints with a large packet size, interrupt latency
-runs the risk of the FIQ starting a transaction too late in a full-speed
-frame. If the device is still transmitting data when EOF2 for the
-downstream frame occurs, the hub will disable the port. This change is
-not reflected in the hub status endpoint and the device becomes
-unresponsive.
-
-Prevent high-bandwidth transactions from being started too late in a
-frame. The mechanism is not guaranteed: a combination of bit stuffing
-and hub latency may still result in a device overrunning.
-
-fiq_fsm: fix bounce buffer utilisation for Isochronous OUT
-
-Multi-packet isochronous OUT transactions were subject to a few bounday
-bugs. Fix them.
-
-Audio playback is now much more robust: however, an issue stands with
-devices that have adaptive sinks - ALSA plays samples too fast.
-
-dwc_otg: Return full-speed frame numbers in HS mode
-
-The frame counter increments on every *microframe* in high-speed mode.
-Most device drivers expect this number to be in full-speed frames - this
-caused considerable confusion to e.g. snd_usb_audio which uses the
-frame counter to estimate the number of samples played.
-
-fiq_fsm: save PID on completion of interrupt OUT transfers
-
-Also add edge case handling for interrupt transports.
-
-Note that for periodic split IN, data toggles are unimplemented in the
-OTG host hardware - it unconditionally accepts any PID.
-
-fiq_fsm: add missing case for fiq_fsm_tt_in_use()
-
-Certain combinations of bitrate and endpoint activity could
-result in a periodic transaction erroneously getting started
-while the previous Isochronous OUT was still active.
-
-fiq_fsm: clear hcintmsk for aborted transactions
-
-Prevents the FIQ from erroneously handling interrupts
-on a timed out channel.
-
-fiq_fsm: enable by default
-
-fiq_fsm: fix dequeues for non-periodic split transactions
-
-If a dequeue happened between the SSPLIT and CSPLIT phases of the
-transaction, the HCD would never receive an interrupt.
-
-fiq_fsm: Disable by default
-
-fiq_fsm: Handle HC babble errors
-
-The HCTSIZ transfer size field raises a babble interrupt if
-the counter wraps. Handle the resulting interrupt in this case.
-
-dwc_otg: fix interrupt registration for fiq_enable=0
-
-Additionally make the module parameter conditional for wherever
-hcd->fiq_state is touched.
-
-fiq_fsm: Enable by default
-
-dwc_otg: Fix various issues with root port and transaction errors
-
-Process the host port interrupts correctly (and don't trample them).
-Root port hotplug now functional again.
-
-Fix a few thinkos with the transaction error passthrough for fiq_fsm.
-
-fiq_fsm: Implement hack for Split Interrupt transactions
-
-Hubs aren't too picky about which endpoint we send Control type split
-transactions to. By treating Interrupt transfers as Control, it is
-possible to use the non-periodic queue in the OTG core as well as the
-non-periodic FIFOs in the hub itself. This massively reduces the
-microframe exclusivity/contention that periodic split transactions
-otherwise have to enforce.
-
-It goes without saying that this is a fairly egregious USB specification
-violation, but it works.
-
-Original idea by Hans Petter Selasky @ FreeBSD.org.
-
-dwc_otg: FIQ support on SMP. Set up FIQ stack and handler on Core 0 only.
-
-dwc_otg: introduce fiq_fsm_spin(un|)lock()
-
-SMP safety for the FIQ relies on register read-modify write cycles being
-completed in the correct order. Several places in the DWC code modify
-registers also touched by the FIQ. Protect these by a bare-bones lock
-mechanism.
-
-This also makes it possible to run the FIQ and IRQ handlers on different
-cores.
-
-fiq_fsm: fix build on bcm2708 and bcm2709 platforms
-
-dwc_otg: put some barriers back where they should be for UP
-
-bcm2709/dwc_otg: Setup FIQ on core 1 if >1 core active
-
-dwc_otg: fixup read-modify-write in critical paths
-
-Be more careful about read-modify-write on registers that the FIQ
-also touches.
-
-Guard fiq_fsm_spin_lock with fiq_enable check
-
-fiq_fsm: Falling out of the state machine isn't fatal
-
-This edge case can be hit if the port is disabled while the FIQ is
-in the middle of a transaction. Make the effects less severe.
-
-Also get rid of the useless return value.
-
-squash: dwc_otg: Allow to build without SMP
-
-usb: core: make overcurrent messages more prominent
-
-Hub overcurrent messages are more serious than "debug". Increase loglevel.
-
-usb: dwc_otg: Don't use dma_to_virt()
-
-Commit 6ce0d20 changes dma_to_virt() which breaks this driver.
-Open code the old dma_to_virt() implementation to work around this.
-
-Limit the use of __bus_to_virt() to cases where transfer_buffer_length
-is set and transfer_buffer is not set. This is done to increase the
-chance that this driver will also work on ARCH_BCM2835.
-
-transfer_buffer should not be NULL if the length is set, but the
-comment in the code indicates that there are situations where this
-might happen. drivers/usb/isp1760/isp1760-hcd.c also has a similar
-comment pointing to a possible: 'usb storage / SCSI bug'.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-dwc_otg: Fix crash when fiq_enable=0
-
-dwc_otg: fiq_fsm: Make high-speed isochronous strided transfers work properly
-
-Certain low-bandwidth high-speed USB devices (specialist audio devices,
-compressed-frame webcams) have packet intervals > 1 microframe.
-
-Stride these transfers in the FIQ by using the start-of-frame interrupt
-to restart the channel at the right time.
-
-dwc_otg: Force host mode to fix incorrect compute module boards
-
-dwc_otg: Add ARCH_BCM2835 support
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-dwc_otg: Simplify FIQ irq number code
-
-Dropping ATAGS means we can simplify the FIQ irq number code.
-Also add error checking on the returned irq number.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-dwc_otg: Remove duplicate gadget probe/unregister function
----
- arch/arm/include/asm/irqflags.h | 16 +-
- arch/arm/kernel/fiqasm.S | 4 +
- drivers/usb/Makefile | 1 +
- drivers/usb/core/generic.c | 1 +
- drivers/usb/core/hub.c | 2 +-
- drivers/usb/core/message.c | 79 +
- drivers/usb/core/otg_whitelist.h | 114 +-
- drivers/usb/gadget/file_storage.c | 3676 ++++++++++
- drivers/usb/host/Kconfig | 13 +
- drivers/usb/host/Makefile | 2 +
- drivers/usb/host/dwc_common_port/Makefile | 58 +
- drivers/usb/host/dwc_common_port/Makefile.fbsd | 17 +
- drivers/usb/host/dwc_common_port/Makefile.linux | 49 +
- drivers/usb/host/dwc_common_port/changes.txt | 174 +
- drivers/usb/host/dwc_common_port/doc/doxygen.cfg | 270 +
- drivers/usb/host/dwc_common_port/dwc_cc.c | 532 ++
- drivers/usb/host/dwc_common_port/dwc_cc.h | 224 +
- drivers/usb/host/dwc_common_port/dwc_common_fbsd.c | 1308 ++++
- .../usb/host/dwc_common_port/dwc_common_linux.c | 1433 ++++
- drivers/usb/host/dwc_common_port/dwc_common_nbsd.c | 1275 ++++
- drivers/usb/host/dwc_common_port/dwc_crypto.c | 308 +
- drivers/usb/host/dwc_common_port/dwc_crypto.h | 111 +
- drivers/usb/host/dwc_common_port/dwc_dh.c | 291 +
- drivers/usb/host/dwc_common_port/dwc_dh.h | 106 +
- drivers/usb/host/dwc_common_port/dwc_list.h | 594 ++
- drivers/usb/host/dwc_common_port/dwc_mem.c | 245 +
- drivers/usb/host/dwc_common_port/dwc_modpow.c | 636 ++
- drivers/usb/host/dwc_common_port/dwc_modpow.h | 34 +
- drivers/usb/host/dwc_common_port/dwc_notifier.c | 319 +
- drivers/usb/host/dwc_common_port/dwc_notifier.h | 122 +
- drivers/usb/host/dwc_common_port/dwc_os.h | 1276 ++++
- drivers/usb/host/dwc_common_port/usb.h | 946 +++
- drivers/usb/host/dwc_otg/Makefile | 82 +
- drivers/usb/host/dwc_otg/doc/doxygen.cfg | 224 +
- drivers/usb/host/dwc_otg/dummy_audio.c | 1575 +++++
- drivers/usb/host/dwc_otg/dwc_cfi_common.h | 142 +
- drivers/usb/host/dwc_otg/dwc_otg_adp.c | 854 +++
- drivers/usb/host/dwc_otg/dwc_otg_adp.h | 80 +
- drivers/usb/host/dwc_otg/dwc_otg_attr.c | 1210 ++++
- drivers/usb/host/dwc_otg/dwc_otg_attr.h | 89 +
- drivers/usb/host/dwc_otg/dwc_otg_cfi.c | 1876 +++++
- drivers/usb/host/dwc_otg/dwc_otg_cfi.h | 320 +
- drivers/usb/host/dwc_otg/dwc_otg_cil.c | 7141 ++++++++++++++++++++
- drivers/usb/host/dwc_otg/dwc_otg_cil.h | 1464 ++++
- drivers/usb/host/dwc_otg/dwc_otg_cil_intr.c | 1594 +++++
- drivers/usb/host/dwc_otg/dwc_otg_core_if.h | 705 ++
- drivers/usb/host/dwc_otg/dwc_otg_dbg.h | 117 +
- drivers/usb/host/dwc_otg/dwc_otg_driver.c | 1757 +++++
- drivers/usb/host/dwc_otg/dwc_otg_driver.h | 86 +
- drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.c | 1355 ++++
- drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.h | 370 +
- drivers/usb/host/dwc_otg/dwc_otg_fiq_stub.S | 80 +
- drivers/usb/host/dwc_otg/dwc_otg_hcd.c | 4257 ++++++++++++
- drivers/usb/host/dwc_otg/dwc_otg_hcd.h | 862 +++
- drivers/usb/host/dwc_otg/dwc_otg_hcd_ddma.c | 1132 ++++
- drivers/usb/host/dwc_otg/dwc_otg_hcd_if.h | 417 ++
- drivers/usb/host/dwc_otg/dwc_otg_hcd_intr.c | 2714 ++++++++
- drivers/usb/host/dwc_otg/dwc_otg_hcd_linux.c | 1005 +++
- drivers/usb/host/dwc_otg/dwc_otg_hcd_queue.c | 957 +++
- drivers/usb/host/dwc_otg/dwc_otg_os_dep.h | 188 +
- drivers/usb/host/dwc_otg/dwc_otg_pcd.c | 2712 ++++++++
- drivers/usb/host/dwc_otg/dwc_otg_pcd.h | 266 +
- drivers/usb/host/dwc_otg/dwc_otg_pcd_if.h | 360 +
- drivers/usb/host/dwc_otg/dwc_otg_pcd_intr.c | 5147 ++++++++++++++
- drivers/usb/host/dwc_otg/dwc_otg_pcd_linux.c | 1280 ++++
- drivers/usb/host/dwc_otg/dwc_otg_regs.h | 2550 +++++++
- drivers/usb/host/dwc_otg/test/Makefile | 16 +
- drivers/usb/host/dwc_otg/test/dwc_otg_test.pm | 337 +
- drivers/usb/host/dwc_otg/test/test_mod_param.pl | 133 +
- drivers/usb/host/dwc_otg/test/test_sysfs.pl | 193 +
- 70 files changed, 59867 insertions(+), 16 deletions(-)
- create mode 100644 drivers/usb/gadget/file_storage.c
- create mode 100644 drivers/usb/host/dwc_common_port/Makefile
- create mode 100644 drivers/usb/host/dwc_common_port/Makefile.fbsd
- create mode 100644 drivers/usb/host/dwc_common_port/Makefile.linux
- create mode 100644 drivers/usb/host/dwc_common_port/changes.txt
- create mode 100644 drivers/usb/host/dwc_common_port/doc/doxygen.cfg
- create mode 100644 drivers/usb/host/dwc_common_port/dwc_cc.c
- create mode 100644 drivers/usb/host/dwc_common_port/dwc_cc.h
- create mode 100644 drivers/usb/host/dwc_common_port/dwc_common_fbsd.c
- create mode 100644 drivers/usb/host/dwc_common_port/dwc_common_linux.c
- create mode 100644 drivers/usb/host/dwc_common_port/dwc_common_nbsd.c
- create mode 100644 drivers/usb/host/dwc_common_port/dwc_crypto.c
- create mode 100644 drivers/usb/host/dwc_common_port/dwc_crypto.h
- create mode 100644 drivers/usb/host/dwc_common_port/dwc_dh.c
- create mode 100644 drivers/usb/host/dwc_common_port/dwc_dh.h
- create mode 100644 drivers/usb/host/dwc_common_port/dwc_list.h
- create mode 100644 drivers/usb/host/dwc_common_port/dwc_mem.c
- create mode 100644 drivers/usb/host/dwc_common_port/dwc_modpow.c
- create mode 100644 drivers/usb/host/dwc_common_port/dwc_modpow.h
- create mode 100644 drivers/usb/host/dwc_common_port/dwc_notifier.c
- create mode 100644 drivers/usb/host/dwc_common_port/dwc_notifier.h
- create mode 100644 drivers/usb/host/dwc_common_port/dwc_os.h
- create mode 100644 drivers/usb/host/dwc_common_port/usb.h
- create mode 100644 drivers/usb/host/dwc_otg/Makefile
- create mode 100644 drivers/usb/host/dwc_otg/doc/doxygen.cfg
- create mode 100644 drivers/usb/host/dwc_otg/dummy_audio.c
- create mode 100644 drivers/usb/host/dwc_otg/dwc_cfi_common.h
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_adp.c
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_adp.h
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_attr.c
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_attr.h
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_cfi.c
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_cfi.h
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_cil.c
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_cil.h
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_cil_intr.c
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_core_if.h
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_dbg.h
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_driver.c
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_driver.h
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.c
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.h
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_fiq_stub.S
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_hcd.c
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_hcd.h
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_hcd_ddma.c
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_hcd_if.h
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_hcd_intr.c
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_hcd_linux.c
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_hcd_queue.c
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_os_dep.h
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_pcd.c
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_pcd.h
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_pcd_if.h
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_pcd_intr.c
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_pcd_linux.c
- create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_regs.h
- create mode 100644 drivers/usb/host/dwc_otg/test/Makefile
- create mode 100644 drivers/usb/host/dwc_otg/test/dwc_otg_test.pm
- create mode 100644 drivers/usb/host/dwc_otg/test/test_mod_param.pl
- create mode 100644 drivers/usb/host/dwc_otg/test/test_sysfs.pl
-
---- a/arch/arm/include/asm/irqflags.h
-+++ b/arch/arm/include/asm/irqflags.h
-@@ -162,13 +162,23 @@ static inline unsigned long arch_local_s
- }
-
- /*
-- * restore saved IRQ & FIQ state
-+ * restore saved IRQ state
- */
- #define arch_local_irq_restore arch_local_irq_restore
- static inline void arch_local_irq_restore(unsigned long flags)
- {
-- asm volatile(
-- " msr " IRQMASK_REG_NAME_W ", %0 @ local_irq_restore"
-+ unsigned long temp = 0;
-+ flags &= ~(1 << 6);
-+ asm volatile (
-+ " mrs %0, cpsr"
-+ : "=r" (temp)
-+ :
-+ : "memory", "cc");
-+ /* Preserve FIQ bit */
-+ temp &= (1 << 6);
-+ flags = flags | temp;
-+ asm volatile (
-+ " msr cpsr_c, %0 @ local_irq_restore"
- :
- : "r" (flags)
- : "memory", "cc");
---- a/arch/arm/kernel/fiqasm.S
-+++ b/arch/arm/kernel/fiqasm.S
-@@ -47,3 +47,7 @@ ENTRY(__get_fiq_regs)
- mov r0, r0 @ avoid hazard prior to ARMv4
- ret lr
- ENDPROC(__get_fiq_regs)
-+
-+ENTRY(__FIQ_Branch)
-+ mov pc, r8
-+ENDPROC(__FIQ_Branch)
---- a/drivers/usb/Makefile
-+++ b/drivers/usb/Makefile
-@@ -7,6 +7,7 @@
- obj-$(CONFIG_USB) += core/
- obj-$(CONFIG_USB_SUPPORT) += phy/
-
-+obj-$(CONFIG_USB_DWCOTG) += host/
- obj-$(CONFIG_USB_DWC3) += dwc3/
- obj-$(CONFIG_USB_DWC2) += dwc2/
- obj-$(CONFIG_USB_ISP1760) += isp1760/
---- a/drivers/usb/core/generic.c
-+++ b/drivers/usb/core/generic.c
-@@ -152,6 +152,7 @@ int usb_choose_configuration(struct usb_
- dev_warn(&udev->dev,
- "no configuration chosen from %d choice%s\n",
- num_configs, plural(num_configs));
-+ dev_warn(&udev->dev, "No support over %dmA\n", udev->bus_mA);
- }
- return i;
- }
---- a/drivers/usb/core/hub.c
-+++ b/drivers/usb/core/hub.c
-@@ -4942,7 +4942,7 @@ static void port_event(struct usb_hub *h
- if (portchange & USB_PORT_STAT_C_OVERCURRENT) {
- u16 status = 0, unused;
-
-- dev_dbg(&port_dev->dev, "over-current change\n");
-+ dev_notice(&port_dev->dev, "over-current change\n");
- usb_clear_port_feature(hdev, port1,
- USB_PORT_FEAT_C_OVER_CURRENT);
- msleep(100); /* Cool down */
---- a/drivers/usb/core/message.c
-+++ b/drivers/usb/core/message.c
-@@ -1909,6 +1909,85 @@ free_interfaces:
- if (cp->string == NULL &&
- !(dev->quirks & USB_QUIRK_CONFIG_INTF_STRINGS))
- cp->string = usb_cache_string(dev, cp->desc.iConfiguration);
-+/* Uncomment this define to enable the HS Electrical Test support */
-+#define DWC_HS_ELECT_TST 1
-+#ifdef DWC_HS_ELECT_TST
-+ /* Here we implement the HS Electrical Test support. The
-+ * tester uses a vendor ID of 0x1A0A to indicate we should
-+ * run a special test sequence. The product ID tells us
-+ * which sequence to run. We invoke the test sequence by
-+ * sending a non-standard SetFeature command to our root
-+ * hub port. Our dwc_otg_hcd_hub_control() routine will
-+ * recognize the command and perform the desired test
-+ * sequence.
-+ */
-+ if (dev->descriptor.idVendor == 0x1A0A) {
-+ /* HSOTG Electrical Test */
-+ dev_warn(&dev->dev, "VID from HSOTG Electrical Test Fixture\n");
-+
-+ if (dev->bus && dev->bus->root_hub) {
-+ struct usb_device *hdev = dev->bus->root_hub;
-+ dev_warn(&dev->dev, "Got PID 0x%x\n", dev->descriptor.idProduct);
-+
-+ switch (dev->descriptor.idProduct) {
-+ case 0x0101: /* TEST_SE0_NAK */
-+ dev_warn(&dev->dev, "TEST_SE0_NAK\n");
-+ usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0),
-+ USB_REQ_SET_FEATURE, USB_RT_PORT,
-+ USB_PORT_FEAT_TEST, 0x300, NULL, 0, HZ);
-+ break;
-+
-+ case 0x0102: /* TEST_J */
-+ dev_warn(&dev->dev, "TEST_J\n");
-+ usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0),
-+ USB_REQ_SET_FEATURE, USB_RT_PORT,
-+ USB_PORT_FEAT_TEST, 0x100, NULL, 0, HZ);
-+ break;
-+
-+ case 0x0103: /* TEST_K */
-+ dev_warn(&dev->dev, "TEST_K\n");
-+ usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0),
-+ USB_REQ_SET_FEATURE, USB_RT_PORT,
-+ USB_PORT_FEAT_TEST, 0x200, NULL, 0, HZ);
-+ break;
-+
-+ case 0x0104: /* TEST_PACKET */
-+ dev_warn(&dev->dev, "TEST_PACKET\n");
-+ usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0),
-+ USB_REQ_SET_FEATURE, USB_RT_PORT,
-+ USB_PORT_FEAT_TEST, 0x400, NULL, 0, HZ);
-+ break;
-+
-+ case 0x0105: /* TEST_FORCE_ENABLE */
-+ dev_warn(&dev->dev, "TEST_FORCE_ENABLE\n");
-+ usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0),
-+ USB_REQ_SET_FEATURE, USB_RT_PORT,
-+ USB_PORT_FEAT_TEST, 0x500, NULL, 0, HZ);
-+ break;
-+
-+ case 0x0106: /* HS_HOST_PORT_SUSPEND_RESUME */
-+ dev_warn(&dev->dev, "HS_HOST_PORT_SUSPEND_RESUME\n");
-+ usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0),
-+ USB_REQ_SET_FEATURE, USB_RT_PORT,
-+ USB_PORT_FEAT_TEST, 0x600, NULL, 0, 40 * HZ);
-+ break;
-+
-+ case 0x0107: /* SINGLE_STEP_GET_DEVICE_DESCRIPTOR setup */
-+ dev_warn(&dev->dev, "SINGLE_STEP_GET_DEVICE_DESCRIPTOR setup\n");
-+ usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0),
-+ USB_REQ_SET_FEATURE, USB_RT_PORT,
-+ USB_PORT_FEAT_TEST, 0x700, NULL, 0, 40 * HZ);
-+ break;
-+
-+ case 0x0108: /* SINGLE_STEP_GET_DEVICE_DESCRIPTOR execute */
-+ dev_warn(&dev->dev, "SINGLE_STEP_GET_DEVICE_DESCRIPTOR execute\n");
-+ usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0),
-+ USB_REQ_SET_FEATURE, USB_RT_PORT,
-+ USB_PORT_FEAT_TEST, 0x800, NULL, 0, 40 * HZ);
-+ }
-+ }
-+ }
-+#endif /* DWC_HS_ELECT_TST */
-
- /* Now that the interfaces are installed, re-enable LPM. */
- usb_unlocked_enable_lpm(dev);
---- a/drivers/usb/core/otg_whitelist.h
-+++ b/drivers/usb/core/otg_whitelist.h
-@@ -19,33 +19,82 @@
- static struct usb_device_id whitelist_table[] = {
-
- /* hubs are optional in OTG, but very handy ... */
-+#define CERT_WITHOUT_HUBS
-+#if defined(CERT_WITHOUT_HUBS)
-+{ USB_DEVICE( 0x0000, 0x0000 ), }, /* Root HUB Only*/
-+#else
- { USB_DEVICE_INFO(USB_CLASS_HUB, 0, 0), },
- { USB_DEVICE_INFO(USB_CLASS_HUB, 0, 1), },
-+{ USB_DEVICE_INFO(USB_CLASS_HUB, 0, 2), },
-+#endif
-
- #ifdef CONFIG_USB_PRINTER /* ignoring nonstatic linkage! */
- /* FIXME actually, printers are NOT supposed to use device classes;
- * they're supposed to use interface classes...
- */
--{ USB_DEVICE_INFO(7, 1, 1) },
--{ USB_DEVICE_INFO(7, 1, 2) },
--{ USB_DEVICE_INFO(7, 1, 3) },
-+//{ USB_DEVICE_INFO(7, 1, 1) },
-+//{ USB_DEVICE_INFO(7, 1, 2) },
-+//{ USB_DEVICE_INFO(7, 1, 3) },
- #endif
-
- #ifdef CONFIG_USB_NET_CDCETHER
- /* Linux-USB CDC Ethernet gadget */
--{ USB_DEVICE(0x0525, 0xa4a1), },
-+//{ USB_DEVICE(0x0525, 0xa4a1), },
- /* Linux-USB CDC Ethernet + RNDIS gadget */
--{ USB_DEVICE(0x0525, 0xa4a2), },
-+//{ USB_DEVICE(0x0525, 0xa4a2), },
- #endif
-
- #if defined(CONFIG_USB_TEST) || defined(CONFIG_USB_TEST_MODULE)
- /* gadget zero, for testing */
--{ USB_DEVICE(0x0525, 0xa4a0), },
-+//{ USB_DEVICE(0x0525, 0xa4a0), },
- #endif
-
-+/* OPT Tester */
-+{ USB_DEVICE( 0x1a0a, 0x0101 ), }, /* TEST_SE0_NAK */
-+{ USB_DEVICE( 0x1a0a, 0x0102 ), }, /* Test_J */
-+{ USB_DEVICE( 0x1a0a, 0x0103 ), }, /* Test_K */
-+{ USB_DEVICE( 0x1a0a, 0x0104 ), }, /* Test_PACKET */
-+{ USB_DEVICE( 0x1a0a, 0x0105 ), }, /* Test_FORCE_ENABLE */
-+{ USB_DEVICE( 0x1a0a, 0x0106 ), }, /* HS_PORT_SUSPEND_RESUME */
-+{ USB_DEVICE( 0x1a0a, 0x0107 ), }, /* SINGLE_STEP_GET_DESCRIPTOR setup */
-+{ USB_DEVICE( 0x1a0a, 0x0108 ), }, /* SINGLE_STEP_GET_DESCRIPTOR execute */
-+
-+/* Sony cameras */
-+{ USB_DEVICE_VER(0x054c,0x0010,0x0410, 0x0500), },
-+
-+/* Memory Devices */
-+//{ USB_DEVICE( 0x0781, 0x5150 ), }, /* SanDisk */
-+//{ USB_DEVICE( 0x05DC, 0x0080 ), }, /* Lexar */
-+//{ USB_DEVICE( 0x4146, 0x9281 ), }, /* IOMEGA */
-+//{ USB_DEVICE( 0x067b, 0x2507 ), }, /* Hammer 20GB External HD */
-+{ USB_DEVICE( 0x0EA0, 0x2168 ), }, /* Ours Technology Inc. (BUFFALO ClipDrive)*/
-+//{ USB_DEVICE( 0x0457, 0x0150 ), }, /* Silicon Integrated Systems Corp. */
-+
-+/* HP Printers */
-+//{ USB_DEVICE( 0x03F0, 0x1102 ), }, /* HP Photosmart 245 */
-+//{ USB_DEVICE( 0x03F0, 0x1302 ), }, /* HP Photosmart 370 Series */
-+
-+/* Speakers */
-+//{ USB_DEVICE( 0x0499, 0x3002 ), }, /* YAMAHA YST-MS35D USB Speakers */
-+//{ USB_DEVICE( 0x0672, 0x1041 ), }, /* Labtec USB Headset */
-+
- { } /* Terminating entry */
- };
-
-+static inline void report_errors(struct usb_device *dev)
-+{
-+ /* OTG MESSAGE: report errors here, customize to match your product */
-+ dev_info(&dev->dev, "device Vendor:%04x Product:%04x is not supported\n",
-+ le16_to_cpu(dev->descriptor.idVendor),
-+ le16_to_cpu(dev->descriptor.idProduct));
-+ if (USB_CLASS_HUB == dev->descriptor.bDeviceClass){
-+ dev_printk(KERN_CRIT, &dev->dev, "Unsupported Hub Topology\n");
-+ } else {
-+ dev_printk(KERN_CRIT, &dev->dev, "Attached Device is not Supported\n");
-+ }
-+}
-+
-+
- static int is_targeted(struct usb_device *dev)
- {
- struct usb_device_id *id = whitelist_table;
-@@ -95,16 +144,57 @@ static int is_targeted(struct usb_device
- continue;
-
- return 1;
-- }
-+ /* NOTE: can't use usb_match_id() since interface caches
-+ * aren't set up yet. this is cut/paste from that code.
-+ */
-+ for (id = whitelist_table; id->match_flags; id++) {
-+#ifdef DEBUG
-+ dev_dbg(&dev->dev,
-+ "ID: V:%04x P:%04x DC:%04x SC:%04x PR:%04x \n",
-+ id->idVendor,
-+ id->idProduct,
-+ id->bDeviceClass,
-+ id->bDeviceSubClass,
-+ id->bDeviceProtocol);
-+#endif
-
-- /* add other match criteria here ... */
-+ if ((id->match_flags & USB_DEVICE_ID_MATCH_VENDOR) &&
-+ id->idVendor != le16_to_cpu(dev->descriptor.idVendor))
-+ continue;
-+
-+ if ((id->match_flags & USB_DEVICE_ID_MATCH_PRODUCT) &&
-+ id->idProduct != le16_to_cpu(dev->descriptor.idProduct))
-+ continue;
-+
-+ /* No need to test id->bcdDevice_lo != 0, since 0 is never
-+ greater than any unsigned number. */
-+ if ((id->match_flags & USB_DEVICE_ID_MATCH_DEV_LO) &&
-+ (id->bcdDevice_lo > le16_to_cpu(dev->descriptor.bcdDevice)))
-+ continue;
-+
-+ if ((id->match_flags & USB_DEVICE_ID_MATCH_DEV_HI) &&
-+ (id->bcdDevice_hi < le16_to_cpu(dev->descriptor.bcdDevice)))
-+ continue;
-+
-+ if ((id->match_flags & USB_DEVICE_ID_MATCH_DEV_CLASS) &&
-+ (id->bDeviceClass != dev->descriptor.bDeviceClass))
-+ continue;
-+
-+ if ((id->match_flags & USB_DEVICE_ID_MATCH_DEV_SUBCLASS) &&
-+ (id->bDeviceSubClass != dev->descriptor.bDeviceSubClass))
-+ continue;
-+
-+ if ((id->match_flags & USB_DEVICE_ID_MATCH_DEV_PROTOCOL) &&
-+ (id->bDeviceProtocol != dev->descriptor.bDeviceProtocol))
-+ continue;
-
-+ return 1;
-+ }
-+ }
-
-- /* OTG MESSAGE: report errors here, customize to match your product */
-- dev_err(&dev->dev, "device v%04x p%04x is not supported\n",
-- le16_to_cpu(dev->descriptor.idVendor),
-- le16_to_cpu(dev->descriptor.idProduct));
-+ /* add other match criteria here ... */
-
-+ report_errors(dev);
- return 0;
- }
-
---- /dev/null
-+++ b/drivers/usb/gadget/file_storage.c
-@@ -0,0 +1,3676 @@
-+/*
-+ * file_storage.c -- File-backed USB Storage Gadget, for USB development
-+ *
-+ * Copyright (C) 2003-2008 Alan Stern
-+ * All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") as published by the Free Software
-+ * Foundation, either version 2 of that License or (at your option) any
-+ * later version.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+
-+/*
-+ * The File-backed Storage Gadget acts as a USB Mass Storage device,
-+ * appearing to the host as a disk drive or as a CD-ROM drive. In addition
-+ * to providing an example of a genuinely useful gadget driver for a USB
-+ * device, it also illustrates a technique of double-buffering for increased
-+ * throughput. Last but not least, it gives an easy way to probe the
-+ * behavior of the Mass Storage drivers in a USB host.
-+ *
-+ * Backing storage is provided by a regular file or a block device, specified
-+ * by the "file" module parameter. Access can be limited to read-only by
-+ * setting the optional "ro" module parameter. (For CD-ROM emulation,
-+ * access is always read-only.) The gadget will indicate that it has
-+ * removable media if the optional "removable" module parameter is set.
-+ *
-+ * The gadget supports the Control-Bulk (CB), Control-Bulk-Interrupt (CBI),
-+ * and Bulk-Only (also known as Bulk-Bulk-Bulk or BBB) transports, selected
-+ * by the optional "transport" module parameter. It also supports the
-+ * following protocols: RBC (0x01), ATAPI or SFF-8020i (0x02), QIC-157 (0c03),
-+ * UFI (0x04), SFF-8070i (0x05), and transparent SCSI (0x06), selected by
-+ * the optional "protocol" module parameter. In addition, the default
-+ * Vendor ID, Product ID, release number and serial number can be overridden.
-+ *
-+ * There is support for multiple logical units (LUNs), each of which has
-+ * its own backing file. The number of LUNs can be set using the optional
-+ * "luns" module parameter (anywhere from 1 to 8), and the corresponding
-+ * files are specified using comma-separated lists for "file" and "ro".
-+ * The default number of LUNs is taken from the number of "file" elements;
-+ * it is 1 if "file" is not given. If "removable" is not set then a backing
-+ * file must be specified for each LUN. If it is set, then an unspecified
-+ * or empty backing filename means the LUN's medium is not loaded. Ideally
-+ * each LUN would be settable independently as a disk drive or a CD-ROM
-+ * drive, but currently all LUNs have to be the same type. The CD-ROM
-+ * emulation includes a single data track and no audio tracks; hence there
-+ * need be only one backing file per LUN.
-+ *
-+ * Requirements are modest; only a bulk-in and a bulk-out endpoint are
-+ * needed (an interrupt-out endpoint is also needed for CBI). The memory
-+ * requirement amounts to two 16K buffers, size configurable by a parameter.
-+ * Support is included for both full-speed and high-speed operation.
-+ *
-+ * Note that the driver is slightly non-portable in that it assumes a
-+ * single memory/DMA buffer will be useable for bulk-in, bulk-out, and
-+ * interrupt-in endpoints. With most device controllers this isn't an
-+ * issue, but there may be some with hardware restrictions that prevent
-+ * a buffer from being used by more than one endpoint.
-+ *
-+ * Module options:
-+ *
-+ * file=filename[,filename...]
-+ * Required if "removable" is not set, names of
-+ * the files or block devices used for
-+ * backing storage
-+ * serial=HHHH... Required serial number (string of hex chars)
-+ * ro=b[,b...] Default false, booleans for read-only access
-+ * removable Default false, boolean for removable media
-+ * luns=N Default N = number of filenames, number of
-+ * LUNs to support
-+ * nofua=b[,b...] Default false, booleans for ignore FUA flag
-+ * in SCSI WRITE(10,12) commands
-+ * stall Default determined according to the type of
-+ * USB device controller (usually true),
-+ * boolean to permit the driver to halt
-+ * bulk endpoints
-+ * cdrom Default false, boolean for whether to emulate
-+ * a CD-ROM drive
-+ * transport=XXX Default BBB, transport name (CB, CBI, or BBB)
-+ * protocol=YYY Default SCSI, protocol name (RBC, 8020 or
-+ * ATAPI, QIC, UFI, 8070, or SCSI;
-+ * also 1 - 6)
-+ * vendor=0xVVVV Default 0x0525 (NetChip), USB Vendor ID
-+ * product=0xPPPP Default 0xa4a5 (FSG), USB Product ID
-+ * release=0xRRRR Override the USB release number (bcdDevice)
-+ * buflen=N Default N=16384, buffer size used (will be
-+ * rounded down to a multiple of
-+ * PAGE_CACHE_SIZE)
-+ *
-+ * If CONFIG_USB_FILE_STORAGE_TEST is not set, only the "file", "serial", "ro",
-+ * "removable", "luns", "nofua", "stall", and "cdrom" options are available;
-+ * default values are used for everything else.
-+ *
-+ * The pathnames of the backing files and the ro settings are available in
-+ * the attribute files "file", "nofua", and "ro" in the lun<n> subdirectory of
-+ * the gadget's sysfs directory. If the "removable" option is set, writing to
-+ * these files will simulate ejecting/loading the medium (writing an empty
-+ * line means eject) and adjusting a write-enable tab. Changes to the ro
-+ * setting are not allowed when the medium is loaded or if CD-ROM emulation
-+ * is being used.
-+ *
-+ * This gadget driver is heavily based on "Gadget Zero" by David Brownell.
-+ * The driver's SCSI command interface was based on the "Information
-+ * technology - Small Computer System Interface - 2" document from
-+ * X3T9.2 Project 375D, Revision 10L, 7-SEP-93, available at
-+ * <http://www.t10.org/ftp/t10/drafts/s2/s2-r10l.pdf>. The single exception
-+ * is opcode 0x23 (READ FORMAT CAPACITIES), which was based on the
-+ * "Universal Serial Bus Mass Storage Class UFI Command Specification"
-+ * document, Revision 1.0, December 14, 1998, available at
-+ * <http://www.usb.org/developers/devclass_docs/usbmass-ufi10.pdf>.
-+ */
-+
-+
-+/*
-+ * Driver Design
-+ *
-+ * The FSG driver is fairly straightforward. There is a main kernel
-+ * thread that handles most of the work. Interrupt routines field
-+ * callbacks from the controller driver: bulk- and interrupt-request
-+ * completion notifications, endpoint-0 events, and disconnect events.
-+ * Completion events are passed to the main thread by wakeup calls. Many
-+ * ep0 requests are handled at interrupt time, but SetInterface,
-+ * SetConfiguration, and device reset requests are forwarded to the
-+ * thread in the form of "exceptions" using SIGUSR1 signals (since they
-+ * should interrupt any ongoing file I/O operations).
-+ *
-+ * The thread's main routine implements the standard command/data/status
-+ * parts of a SCSI interaction. It and its subroutines are full of tests
-+ * for pending signals/exceptions -- all this polling is necessary since
-+ * the kernel has no setjmp/longjmp equivalents. (Maybe this is an
-+ * indication that the driver really wants to be running in userspace.)
-+ * An important point is that so long as the thread is alive it keeps an
-+ * open reference to the backing file. This will prevent unmounting
-+ * the backing file's underlying filesystem and could cause problems
-+ * during system shutdown, for example. To prevent such problems, the
-+ * thread catches INT, TERM, and KILL signals and converts them into
-+ * an EXIT exception.
-+ *
-+ * In normal operation the main thread is started during the gadget's
-+ * fsg_bind() callback and stopped during fsg_unbind(). But it can also
-+ * exit when it receives a signal, and there's no point leaving the
-+ * gadget running when the thread is dead. So just before the thread
-+ * exits, it deregisters the gadget driver. This makes things a little
-+ * tricky: The driver is deregistered at two places, and the exiting
-+ * thread can indirectly call fsg_unbind() which in turn can tell the
-+ * thread to exit. The first problem is resolved through the use of the
-+ * REGISTERED atomic bitflag; the driver will only be deregistered once.
-+ * The second problem is resolved by having fsg_unbind() check
-+ * fsg->state; it won't try to stop the thread if the state is already
-+ * FSG_STATE_TERMINATED.
-+ *
-+ * To provide maximum throughput, the driver uses a circular pipeline of
-+ * buffer heads (struct fsg_buffhd). In principle the pipeline can be
-+ * arbitrarily long; in practice the benefits don't justify having more
-+ * than 2 stages (i.e., double buffering). But it helps to think of the
-+ * pipeline as being a long one. Each buffer head contains a bulk-in and
-+ * a bulk-out request pointer (since the buffer can be used for both
-+ * output and input -- directions always are given from the host's
-+ * point of view) as well as a pointer to the buffer and various state
-+ * variables.
-+ *
-+ * Use of the pipeline follows a simple protocol. There is a variable
-+ * (fsg->next_buffhd_to_fill) that points to the next buffer head to use.
-+ * At any time that buffer head may still be in use from an earlier
-+ * request, so each buffer head has a state variable indicating whether
-+ * it is EMPTY, FULL, or BUSY. Typical use involves waiting for the
-+ * buffer head to be EMPTY, filling the buffer either by file I/O or by
-+ * USB I/O (during which the buffer head is BUSY), and marking the buffer
-+ * head FULL when the I/O is complete. Then the buffer will be emptied
-+ * (again possibly by USB I/O, during which it is marked BUSY) and
-+ * finally marked EMPTY again (possibly by a completion routine).
-+ *
-+ * A module parameter tells the driver to avoid stalling the bulk
-+ * endpoints wherever the transport specification allows. This is
-+ * necessary for some UDCs like the SuperH, which cannot reliably clear a
-+ * halt on a bulk endpoint. However, under certain circumstances the
-+ * Bulk-only specification requires a stall. In such cases the driver
-+ * will halt the endpoint and set a flag indicating that it should clear
-+ * the halt in software during the next device reset. Hopefully this
-+ * will permit everything to work correctly. Furthermore, although the
-+ * specification allows the bulk-out endpoint to halt when the host sends
-+ * too much data, implementing this would cause an unavoidable race.
-+ * The driver will always use the "no-stall" approach for OUT transfers.
-+ *
-+ * One subtle point concerns sending status-stage responses for ep0
-+ * requests. Some of these requests, such as device reset, can involve
-+ * interrupting an ongoing file I/O operation, which might take an
-+ * arbitrarily long time. During that delay the host might give up on
-+ * the original ep0 request and issue a new one. When that happens the
-+ * driver should not notify the host about completion of the original
-+ * request, as the host will no longer be waiting for it. So the driver
-+ * assigns to each ep0 request a unique tag, and it keeps track of the
-+ * tag value of the request associated with a long-running exception
-+ * (device-reset, interface-change, or configuration-change). When the
-+ * exception handler is finished, the status-stage response is submitted
-+ * only if the current ep0 request tag is equal to the exception request
-+ * tag. Thus only the most recently received ep0 request will get a
-+ * status-stage response.
-+ *
-+ * Warning: This driver source file is too long. It ought to be split up
-+ * into a header file plus about 3 separate .c files, to handle the details
-+ * of the Gadget, USB Mass Storage, and SCSI protocols.
-+ */
-+
-+
-+/* #define VERBOSE_DEBUG */
-+/* #define DUMP_MSGS */
-+
-+
-+#include <linux/blkdev.h>
-+#include <linux/completion.h>
-+#include <linux/dcache.h>
-+#include <linux/delay.h>
-+#include <linux/device.h>
-+#include <linux/fcntl.h>
-+#include <linux/file.h>
-+#include <linux/fs.h>
-+#include <linux/kref.h>
-+#include <linux/kthread.h>
-+#include <linux/limits.h>
-+#include <linux/module.h>
-+#include <linux/rwsem.h>
-+#include <linux/slab.h>
-+#include <linux/spinlock.h>
-+#include <linux/string.h>
-+#include <linux/freezer.h>
-+#include <linux/utsname.h>
-+
-+#include <linux/usb/ch9.h>
-+#include <linux/usb/gadget.h>
-+
-+#include "gadget_chips.h"
-+
-+
-+
-+/*
-+ * Kbuild is not very cooperative with respect to linking separately
-+ * compiled library objects into one module. So for now we won't use
-+ * separate compilation ... ensuring init/exit sections work to shrink
-+ * the runtime footprint, and giving us at least some parts of what
-+ * a "gcc --combine ... part1.c part2.c part3.c ... " build would.
-+ */
-+#include "usbstring.c"
-+#include "config.c"
-+#include "epautoconf.c"
-+
-+/*-------------------------------------------------------------------------*/
-+
-+#define DRIVER_DESC "File-backed Storage Gadget"
-+#define DRIVER_NAME "g_file_storage"
-+#define DRIVER_VERSION "1 September 2010"
-+
-+static char fsg_string_manufacturer[64];
-+static const char fsg_string_product[] = DRIVER_DESC;
-+static const char fsg_string_config[] = "Self-powered";
-+static const char fsg_string_interface[] = "Mass Storage";
-+
-+
-+#include "storage_common.c"
-+
-+
-+MODULE_DESCRIPTION(DRIVER_DESC);
-+MODULE_AUTHOR("Alan Stern");
-+MODULE_LICENSE("Dual BSD/GPL");
-+
-+/*
-+ * This driver assumes self-powered hardware and has no way for users to
-+ * trigger remote wakeup. It uses autoconfiguration to select endpoints
-+ * and endpoint addresses.
-+ */
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+
-+/* Encapsulate the module parameter settings */
-+
-+static struct {
-+ char *file[FSG_MAX_LUNS];
-+ char *serial;
-+ bool ro[FSG_MAX_LUNS];
-+ bool nofua[FSG_MAX_LUNS];
-+ unsigned int num_filenames;
-+ unsigned int num_ros;
-+ unsigned int num_nofuas;
-+ unsigned int nluns;
-+
-+ bool removable;
-+ bool can_stall;
-+ bool cdrom;
-+
-+ char *transport_parm;
-+ char *protocol_parm;
-+ unsigned short vendor;
-+ unsigned short product;
-+ unsigned short release;
-+ unsigned int buflen;
-+
-+ int transport_type;
-+ char *transport_name;
-+ int protocol_type;
-+ char *protocol_name;
-+
-+} mod_data = { // Default values
-+ .transport_parm = "BBB",
-+ .protocol_parm = "SCSI",
-+ .removable = 0,
-+ .can_stall = 1,
-+ .cdrom = 0,
-+ .vendor = FSG_VENDOR_ID,
-+ .product = FSG_PRODUCT_ID,
-+ .release = 0xffff, // Use controller chip type
-+ .buflen = 16384,
-+ };
-+
-+
-+module_param_array_named(file, mod_data.file, charp, &mod_data.num_filenames,
-+ S_IRUGO);
-+MODULE_PARM_DESC(file, "names of backing files or devices");
-+
-+module_param_named(serial, mod_data.serial, charp, S_IRUGO);
-+MODULE_PARM_DESC(serial, "USB serial number");
-+
-+module_param_array_named(ro, mod_data.ro, bool, &mod_data.num_ros, S_IRUGO);
-+MODULE_PARM_DESC(ro, "true to force read-only");
-+
-+module_param_array_named(nofua, mod_data.nofua, bool, &mod_data.num_nofuas,
-+ S_IRUGO);
-+MODULE_PARM_DESC(nofua, "true to ignore SCSI WRITE(10,12) FUA bit");
-+
-+module_param_named(luns, mod_data.nluns, uint, S_IRUGO);
-+MODULE_PARM_DESC(luns, "number of LUNs");
-+
-+module_param_named(removable, mod_data.removable, bool, S_IRUGO);
-+MODULE_PARM_DESC(removable, "true to simulate removable media");
-+
-+module_param_named(stall, mod_data.can_stall, bool, S_IRUGO);
-+MODULE_PARM_DESC(stall, "false to prevent bulk stalls");
-+
-+module_param_named(cdrom, mod_data.cdrom, bool, S_IRUGO);
-+MODULE_PARM_DESC(cdrom, "true to emulate cdrom instead of disk");
-+
-+/* In the non-TEST version, only the module parameters listed above
-+ * are available. */
-+#ifdef CONFIG_USB_FILE_STORAGE_TEST
-+
-+module_param_named(transport, mod_data.transport_parm, charp, S_IRUGO);
-+MODULE_PARM_DESC(transport, "type of transport (BBB, CBI, or CB)");
-+
-+module_param_named(protocol, mod_data.protocol_parm, charp, S_IRUGO);
-+MODULE_PARM_DESC(protocol, "type of protocol (RBC, 8020, QIC, UFI, "
-+ "8070, or SCSI)");
-+
-+module_param_named(vendor, mod_data.vendor, ushort, S_IRUGO);
-+MODULE_PARM_DESC(vendor, "USB Vendor ID");
-+
-+module_param_named(product, mod_data.product, ushort, S_IRUGO);
-+MODULE_PARM_DESC(product, "USB Product ID");
-+
-+module_param_named(release, mod_data.release, ushort, S_IRUGO);
-+MODULE_PARM_DESC(release, "USB release number");
-+
-+module_param_named(buflen, mod_data.buflen, uint, S_IRUGO);
-+MODULE_PARM_DESC(buflen, "I/O buffer size");
-+
-+#endif /* CONFIG_USB_FILE_STORAGE_TEST */
-+
-+
-+/*
-+ * These definitions will permit the compiler to avoid generating code for
-+ * parts of the driver that aren't used in the non-TEST version. Even gcc
-+ * can recognize when a test of a constant expression yields a dead code
-+ * path.
-+ */
-+
-+#ifdef CONFIG_USB_FILE_STORAGE_TEST
-+
-+#define transport_is_bbb() (mod_data.transport_type == USB_PR_BULK)
-+#define transport_is_cbi() (mod_data.transport_type == USB_PR_CBI)
-+#define protocol_is_scsi() (mod_data.protocol_type == USB_SC_SCSI)
-+
-+#else
-+
-+#define transport_is_bbb() 1
-+#define transport_is_cbi() 0
-+#define protocol_is_scsi() 1
-+
-+#endif /* CONFIG_USB_FILE_STORAGE_TEST */
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+
-+struct fsg_dev {
-+ /* lock protects: state, all the req_busy's, and cbbuf_cmnd */
-+ spinlock_t lock;
-+ struct usb_gadget *gadget;
-+
-+ /* filesem protects: backing files in use */
-+ struct rw_semaphore filesem;
-+
-+ /* reference counting: wait until all LUNs are released */
-+ struct kref ref;
-+
-+ struct usb_ep *ep0; // Handy copy of gadget->ep0
-+ struct usb_request *ep0req; // For control responses
-+ unsigned int ep0_req_tag;
-+ const char *ep0req_name;
-+
-+ struct usb_request *intreq; // For interrupt responses
-+ int intreq_busy;
-+ struct fsg_buffhd *intr_buffhd;
-+
-+ unsigned int bulk_out_maxpacket;
-+ enum fsg_state state; // For exception handling
-+ unsigned int exception_req_tag;
-+
-+ u8 config, new_config;
-+
-+ unsigned int running : 1;
-+ unsigned int bulk_in_enabled : 1;
-+ unsigned int bulk_out_enabled : 1;
-+ unsigned int intr_in_enabled : 1;
-+ unsigned int phase_error : 1;
-+ unsigned int short_packet_received : 1;
-+ unsigned int bad_lun_okay : 1;
-+
-+ unsigned long atomic_bitflags;
-+#define REGISTERED 0
-+#define IGNORE_BULK_OUT 1
-+#define SUSPENDED 2
-+
-+ struct usb_ep *bulk_in;
-+ struct usb_ep *bulk_out;
-+ struct usb_ep *intr_in;
-+
-+ struct fsg_buffhd *next_buffhd_to_fill;
-+ struct fsg_buffhd *next_buffhd_to_drain;
-+
-+ int thread_wakeup_needed;
-+ struct completion thread_notifier;
-+ struct task_struct *thread_task;
-+
-+ int cmnd_size;
-+ u8 cmnd[MAX_COMMAND_SIZE];
-+ enum data_direction data_dir;
-+ u32 data_size;
-+ u32 data_size_from_cmnd;
-+ u32 tag;
-+ unsigned int lun;
-+ u32 residue;
-+ u32 usb_amount_left;
-+
-+ /* The CB protocol offers no way for a host to know when a command
-+ * has completed. As a result the next command may arrive early,
-+ * and we will still have to handle it. For that reason we need
-+ * a buffer to store new commands when using CB (or CBI, which
-+ * does not oblige a host to wait for command completion either). */
-+ int cbbuf_cmnd_size;
-+ u8 cbbuf_cmnd[MAX_COMMAND_SIZE];
-+
-+ unsigned int nluns;
-+ struct fsg_lun *luns;
-+ struct fsg_lun *curlun;
-+ /* Must be the last entry */
-+ struct fsg_buffhd buffhds[];
-+};
-+
-+typedef void (*fsg_routine_t)(struct fsg_dev *);
-+
-+static int exception_in_progress(struct fsg_dev *fsg)
-+{
-+ return (fsg->state > FSG_STATE_IDLE);
-+}
-+
-+/* Make bulk-out requests be divisible by the maxpacket size */
-+static void set_bulk_out_req_length(struct fsg_dev *fsg,
-+ struct fsg_buffhd *bh, unsigned int length)
-+{
-+ unsigned int rem;
-+
-+ bh->bulk_out_intended_length = length;
-+ rem = length % fsg->bulk_out_maxpacket;
-+ if (rem > 0)
-+ length += fsg->bulk_out_maxpacket - rem;
-+ bh->outreq->length = length;
-+}
-+
-+static struct fsg_dev *the_fsg;
-+static struct usb_gadget_driver fsg_driver;
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+static int fsg_set_halt(struct fsg_dev *fsg, struct usb_ep *ep)
-+{
-+ const char *name;
-+
-+ if (ep == fsg->bulk_in)
-+ name = "bulk-in";
-+ else if (ep == fsg->bulk_out)
-+ name = "bulk-out";
-+ else
-+ name = ep->name;
-+ DBG(fsg, "%s set halt\n", name);
-+ return usb_ep_set_halt(ep);
-+}
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+/*
-+ * DESCRIPTORS ... most are static, but strings and (full) configuration
-+ * descriptors are built on demand. Also the (static) config and interface
-+ * descriptors are adjusted during fsg_bind().
-+ */
-+
-+/* There is only one configuration. */
-+#define CONFIG_VALUE 1
-+
-+static struct usb_device_descriptor
-+device_desc = {
-+ .bLength = sizeof device_desc,
-+ .bDescriptorType = USB_DT_DEVICE,
-+
-+ .bcdUSB = cpu_to_le16(0x0200),
-+ .bDeviceClass = USB_CLASS_PER_INTERFACE,
-+
-+ /* The next three values can be overridden by module parameters */
-+ .idVendor = cpu_to_le16(FSG_VENDOR_ID),
-+ .idProduct = cpu_to_le16(FSG_PRODUCT_ID),
-+ .bcdDevice = cpu_to_le16(0xffff),
-+
-+ .iManufacturer = FSG_STRING_MANUFACTURER,
-+ .iProduct = FSG_STRING_PRODUCT,
-+ .iSerialNumber = FSG_STRING_SERIAL,
-+ .bNumConfigurations = 1,
-+};
-+
-+static struct usb_config_descriptor
-+config_desc = {
-+ .bLength = sizeof config_desc,
-+ .bDescriptorType = USB_DT_CONFIG,
-+
-+ /* wTotalLength computed by usb_gadget_config_buf() */
-+ .bNumInterfaces = 1,
-+ .bConfigurationValue = CONFIG_VALUE,
-+ .iConfiguration = FSG_STRING_CONFIG,
-+ .bmAttributes = USB_CONFIG_ATT_ONE | USB_CONFIG_ATT_SELFPOWER,
-+ .bMaxPower = CONFIG_USB_GADGET_VBUS_DRAW / 2,
-+};
-+
-+
-+static struct usb_qualifier_descriptor
-+dev_qualifier = {
-+ .bLength = sizeof dev_qualifier,
-+ .bDescriptorType = USB_DT_DEVICE_QUALIFIER,
-+
-+ .bcdUSB = cpu_to_le16(0x0200),
-+ .bDeviceClass = USB_CLASS_PER_INTERFACE,
-+
-+ .bNumConfigurations = 1,
-+};
-+
-+static int populate_bos(struct fsg_dev *fsg, u8 *buf)
-+{
-+ memcpy(buf, &fsg_bos_desc, USB_DT_BOS_SIZE);
-+ buf += USB_DT_BOS_SIZE;
-+
-+ memcpy(buf, &fsg_ext_cap_desc, USB_DT_USB_EXT_CAP_SIZE);
-+ buf += USB_DT_USB_EXT_CAP_SIZE;
-+
-+ memcpy(buf, &fsg_ss_cap_desc, USB_DT_USB_SS_CAP_SIZE);
-+
-+ return USB_DT_BOS_SIZE + USB_DT_USB_SS_CAP_SIZE
-+ + USB_DT_USB_EXT_CAP_SIZE;
-+}
-+
-+/*
-+ * Config descriptors must agree with the code that sets configurations
-+ * and with code managing interfaces and their altsettings. They must
-+ * also handle different speeds and other-speed requests.
-+ */
-+static int populate_config_buf(struct usb_gadget *gadget,
-+ u8 *buf, u8 type, unsigned index)
-+{
-+ enum usb_device_speed speed = gadget->speed;
-+ int len;
-+ const struct usb_descriptor_header **function;
-+
-+ if (index > 0)
-+ return -EINVAL;
-+
-+ if (gadget_is_dualspeed(gadget) && type == USB_DT_OTHER_SPEED_CONFIG)
-+ speed = (USB_SPEED_FULL + USB_SPEED_HIGH) - speed;
-+ function = gadget_is_dualspeed(gadget) && speed == USB_SPEED_HIGH
-+ ? (const struct usb_descriptor_header **)fsg_hs_function
-+ : (const struct usb_descriptor_header **)fsg_fs_function;
-+
-+ /* for now, don't advertise srp-only devices */
-+ if (!gadget_is_otg(gadget))
-+ function++;
-+
-+ len = usb_gadget_config_buf(&config_desc, buf, EP0_BUFSIZE, function);
-+ ((struct usb_config_descriptor *) buf)->bDescriptorType = type;
-+ return len;
-+}
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+/* These routines may be called in process context or in_irq */
-+
-+/* Caller must hold fsg->lock */
-+static void wakeup_thread(struct fsg_dev *fsg)
-+{
-+ /* Tell the main thread that something has happened */
-+ fsg->thread_wakeup_needed = 1;
-+ if (fsg->thread_task)
-+ wake_up_process(fsg->thread_task);
-+}
-+
-+
-+static void raise_exception(struct fsg_dev *fsg, enum fsg_state new_state)
-+{
-+ unsigned long flags;
-+
-+ /* Do nothing if a higher-priority exception is already in progress.
-+ * If a lower-or-equal priority exception is in progress, preempt it
-+ * and notify the main thread by sending it a signal. */
-+ spin_lock_irqsave(&fsg->lock, flags);
-+ if (fsg->state <= new_state) {
-+ fsg->exception_req_tag = fsg->ep0_req_tag;
-+ fsg->state = new_state;
-+ if (fsg->thread_task)
-+ send_sig_info(SIGUSR1, SEND_SIG_FORCED,
-+ fsg->thread_task);
-+ }
-+ spin_unlock_irqrestore(&fsg->lock, flags);
-+}
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+/* The disconnect callback and ep0 routines. These always run in_irq,
-+ * except that ep0_queue() is called in the main thread to acknowledge
-+ * completion of various requests: set config, set interface, and
-+ * Bulk-only device reset. */
-+
-+static void fsg_disconnect(struct usb_gadget *gadget)
-+{
-+ struct fsg_dev *fsg = get_gadget_data(gadget);
-+
-+ DBG(fsg, "disconnect or port reset\n");
-+ raise_exception(fsg, FSG_STATE_DISCONNECT);
-+}
-+
-+
-+static int ep0_queue(struct fsg_dev *fsg)
-+{
-+ int rc;
-+
-+ rc = usb_ep_queue(fsg->ep0, fsg->ep0req, GFP_ATOMIC);
-+ if (rc != 0 && rc != -ESHUTDOWN) {
-+
-+ /* We can't do much more than wait for a reset */
-+ WARNING(fsg, "error in submission: %s --> %d\n",
-+ fsg->ep0->name, rc);
-+ }
-+ return rc;
-+}
-+
-+static void ep0_complete(struct usb_ep *ep, struct usb_request *req)
-+{
-+ struct fsg_dev *fsg = ep->driver_data;
-+
-+ if (req->actual > 0)
-+ dump_msg(fsg, fsg->ep0req_name, req->buf, req->actual);
-+ if (req->status || req->actual != req->length)
-+ DBG(fsg, "%s --> %d, %u/%u\n", __func__,
-+ req->status, req->actual, req->length);
-+ if (req->status == -ECONNRESET) // Request was cancelled
-+ usb_ep_fifo_flush(ep);
-+
-+ if (req->status == 0 && req->context)
-+ ((fsg_routine_t) (req->context))(fsg);
-+}
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+/* Bulk and interrupt endpoint completion handlers.
-+ * These always run in_irq. */
-+
-+static void bulk_in_complete(struct usb_ep *ep, struct usb_request *req)
-+{
-+ struct fsg_dev *fsg = ep->driver_data;
-+ struct fsg_buffhd *bh = req->context;
-+
-+ if (req->status || req->actual != req->length)
-+ DBG(fsg, "%s --> %d, %u/%u\n", __func__,
-+ req->status, req->actual, req->length);
-+ if (req->status == -ECONNRESET) // Request was cancelled
-+ usb_ep_fifo_flush(ep);
-+
-+ /* Hold the lock while we update the request and buffer states */
-+ smp_wmb();
-+ spin_lock(&fsg->lock);
-+ bh->inreq_busy = 0;
-+ bh->state = BUF_STATE_EMPTY;
-+ wakeup_thread(fsg);
-+ spin_unlock(&fsg->lock);
-+}
-+
-+static void bulk_out_complete(struct usb_ep *ep, struct usb_request *req)
-+{
-+ struct fsg_dev *fsg = ep->driver_data;
-+ struct fsg_buffhd *bh = req->context;
-+
-+ dump_msg(fsg, "bulk-out", req->buf, req->actual);
-+ if (req->status || req->actual != bh->bulk_out_intended_length)
-+ DBG(fsg, "%s --> %d, %u/%u\n", __func__,
-+ req->status, req->actual,
-+ bh->bulk_out_intended_length);
-+ if (req->status == -ECONNRESET) // Request was cancelled
-+ usb_ep_fifo_flush(ep);
-+
-+ /* Hold the lock while we update the request and buffer states */
-+ smp_wmb();
-+ spin_lock(&fsg->lock);
-+ bh->outreq_busy = 0;
-+ bh->state = BUF_STATE_FULL;
-+ wakeup_thread(fsg);
-+ spin_unlock(&fsg->lock);
-+}
-+
-+
-+#ifdef CONFIG_USB_FILE_STORAGE_TEST
-+static void intr_in_complete(struct usb_ep *ep, struct usb_request *req)
-+{
-+ struct fsg_dev *fsg = ep->driver_data;
-+ struct fsg_buffhd *bh = req->context;
-+
-+ if (req->status || req->actual != req->length)
-+ DBG(fsg, "%s --> %d, %u/%u\n", __func__,
-+ req->status, req->actual, req->length);
-+ if (req->status == -ECONNRESET) // Request was cancelled
-+ usb_ep_fifo_flush(ep);
-+
-+ /* Hold the lock while we update the request and buffer states */
-+ smp_wmb();
-+ spin_lock(&fsg->lock);
-+ fsg->intreq_busy = 0;
-+ bh->state = BUF_STATE_EMPTY;
-+ wakeup_thread(fsg);
-+ spin_unlock(&fsg->lock);
-+}
-+
-+#else
-+static void intr_in_complete(struct usb_ep *ep, struct usb_request *req)
-+{}
-+#endif /* CONFIG_USB_FILE_STORAGE_TEST */
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+/* Ep0 class-specific handlers. These always run in_irq. */
-+
-+#ifdef CONFIG_USB_FILE_STORAGE_TEST
-+static void received_cbi_adsc(struct fsg_dev *fsg, struct fsg_buffhd *bh)
-+{
-+ struct usb_request *req = fsg->ep0req;
-+ static u8 cbi_reset_cmnd[6] = {
-+ SEND_DIAGNOSTIC, 4, 0xff, 0xff, 0xff, 0xff};
-+
-+ /* Error in command transfer? */
-+ if (req->status || req->length != req->actual ||
-+ req->actual < 6 || req->actual > MAX_COMMAND_SIZE) {
-+
-+ /* Not all controllers allow a protocol stall after
-+ * receiving control-out data, but we'll try anyway. */
-+ fsg_set_halt(fsg, fsg->ep0);
-+ return; // Wait for reset
-+ }
-+
-+ /* Is it the special reset command? */
-+ if (req->actual >= sizeof cbi_reset_cmnd &&
-+ memcmp(req->buf, cbi_reset_cmnd,
-+ sizeof cbi_reset_cmnd) == 0) {
-+
-+ /* Raise an exception to stop the current operation
-+ * and reinitialize our state. */
-+ DBG(fsg, "cbi reset request\n");
-+ raise_exception(fsg, FSG_STATE_RESET);
-+ return;
-+ }
-+
-+ VDBG(fsg, "CB[I] accept device-specific command\n");
-+ spin_lock(&fsg->lock);
-+
-+ /* Save the command for later */
-+ if (fsg->cbbuf_cmnd_size)
-+ WARNING(fsg, "CB[I] overwriting previous command\n");
-+ fsg->cbbuf_cmnd_size = req->actual;
-+ memcpy(fsg->cbbuf_cmnd, req->buf, fsg->cbbuf_cmnd_size);
-+
-+ wakeup_thread(fsg);
-+ spin_unlock(&fsg->lock);
-+}
-+
-+#else
-+static void received_cbi_adsc(struct fsg_dev *fsg, struct fsg_buffhd *bh)
-+{}
-+#endif /* CONFIG_USB_FILE_STORAGE_TEST */
-+
-+
-+static int class_setup_req(struct fsg_dev *fsg,
-+ const struct usb_ctrlrequest *ctrl)
-+{
-+ struct usb_request *req = fsg->ep0req;
-+ int value = -EOPNOTSUPP;
-+ u16 w_index = le16_to_cpu(ctrl->wIndex);
-+ u16 w_value = le16_to_cpu(ctrl->wValue);
-+ u16 w_length = le16_to_cpu(ctrl->wLength);
-+
-+ if (!fsg->config)
-+ return value;
-+
-+ /* Handle Bulk-only class-specific requests */
-+ if (transport_is_bbb()) {
-+ switch (ctrl->bRequest) {
-+
-+ case US_BULK_RESET_REQUEST:
-+ if (ctrl->bRequestType != (USB_DIR_OUT |
-+ USB_TYPE_CLASS | USB_RECIP_INTERFACE))
-+ break;
-+ if (w_index != 0 || w_value != 0 || w_length != 0) {
-+ value = -EDOM;
-+ break;
-+ }
-+
-+ /* Raise an exception to stop the current operation
-+ * and reinitialize our state. */
-+ DBG(fsg, "bulk reset request\n");
-+ raise_exception(fsg, FSG_STATE_RESET);
-+ value = DELAYED_STATUS;
-+ break;
-+
-+ case US_BULK_GET_MAX_LUN:
-+ if (ctrl->bRequestType != (USB_DIR_IN |
-+ USB_TYPE_CLASS | USB_RECIP_INTERFACE))
-+ break;
-+ if (w_index != 0 || w_value != 0 || w_length != 1) {
-+ value = -EDOM;
-+ break;
-+ }
-+ VDBG(fsg, "get max LUN\n");
-+ *(u8 *) req->buf = fsg->nluns - 1;
-+ value = 1;
-+ break;
-+ }
-+ }
-+
-+ /* Handle CBI class-specific requests */
-+ else {
-+ switch (ctrl->bRequest) {
-+
-+ case USB_CBI_ADSC_REQUEST:
-+ if (ctrl->bRequestType != (USB_DIR_OUT |
-+ USB_TYPE_CLASS | USB_RECIP_INTERFACE))
-+ break;
-+ if (w_index != 0 || w_value != 0) {
-+ value = -EDOM;
-+ break;
-+ }
-+ if (w_length > MAX_COMMAND_SIZE) {
-+ value = -EOVERFLOW;
-+ break;
-+ }
-+ value = w_length;
-+ fsg->ep0req->context = received_cbi_adsc;
-+ break;
-+ }
-+ }
-+
-+ if (value == -EOPNOTSUPP)
-+ VDBG(fsg,
-+ "unknown class-specific control req "
-+ "%02x.%02x v%04x i%04x l%u\n",
-+ ctrl->bRequestType, ctrl->bRequest,
-+ le16_to_cpu(ctrl->wValue), w_index, w_length);
-+ return value;
-+}
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+/* Ep0 standard request handlers. These always run in_irq. */
-+
-+static int standard_setup_req(struct fsg_dev *fsg,
-+ const struct usb_ctrlrequest *ctrl)
-+{
-+ struct usb_request *req = fsg->ep0req;
-+ int value = -EOPNOTSUPP;
-+ u16 w_index = le16_to_cpu(ctrl->wIndex);
-+ u16 w_value = le16_to_cpu(ctrl->wValue);
-+
-+ /* Usually this just stores reply data in the pre-allocated ep0 buffer,
-+ * but config change events will also reconfigure hardware. */
-+ switch (ctrl->bRequest) {
-+
-+ case USB_REQ_GET_DESCRIPTOR:
-+ if (ctrl->bRequestType != (USB_DIR_IN | USB_TYPE_STANDARD |
-+ USB_RECIP_DEVICE))
-+ break;
-+ switch (w_value >> 8) {
-+
-+ case USB_DT_DEVICE:
-+ VDBG(fsg, "get device descriptor\n");
-+ device_desc.bMaxPacketSize0 = fsg->ep0->maxpacket;
-+ value = sizeof device_desc;
-+ memcpy(req->buf, &device_desc, value);
-+ break;
-+ case USB_DT_DEVICE_QUALIFIER:
-+ VDBG(fsg, "get device qualifier\n");
-+ if (!gadget_is_dualspeed(fsg->gadget) ||
-+ fsg->gadget->speed == USB_SPEED_SUPER)
-+ break;
-+ /*
-+ * Assume ep0 uses the same maxpacket value for both
-+ * speeds
-+ */
-+ dev_qualifier.bMaxPacketSize0 = fsg->ep0->maxpacket;
-+ value = sizeof dev_qualifier;
-+ memcpy(req->buf, &dev_qualifier, value);
-+ break;
-+
-+ case USB_DT_OTHER_SPEED_CONFIG:
-+ VDBG(fsg, "get other-speed config descriptor\n");
-+ if (!gadget_is_dualspeed(fsg->gadget) ||
-+ fsg->gadget->speed == USB_SPEED_SUPER)
-+ break;
-+ goto get_config;
-+ case USB_DT_CONFIG:
-+ VDBG(fsg, "get configuration descriptor\n");
-+get_config:
-+ value = populate_config_buf(fsg->gadget,
-+ req->buf,
-+ w_value >> 8,
-+ w_value & 0xff);
-+ break;
-+
-+ case USB_DT_STRING:
-+ VDBG(fsg, "get string descriptor\n");
-+
-+ /* wIndex == language code */
-+ value = usb_gadget_get_string(&fsg_stringtab,
-+ w_value & 0xff, req->buf);
-+ break;
-+
-+ case USB_DT_BOS:
-+ VDBG(fsg, "get bos descriptor\n");
-+
-+ if (gadget_is_superspeed(fsg->gadget))
-+ value = populate_bos(fsg, req->buf);
-+ break;
-+ }
-+
-+ break;
-+
-+ /* One config, two speeds */
-+ case USB_REQ_SET_CONFIGURATION:
-+ if (ctrl->bRequestType != (USB_DIR_OUT | USB_TYPE_STANDARD |
-+ USB_RECIP_DEVICE))
-+ break;
-+ VDBG(fsg, "set configuration\n");
-+ if (w_value == CONFIG_VALUE || w_value == 0) {
-+ fsg->new_config = w_value;
-+
-+ /* Raise an exception to wipe out previous transaction
-+ * state (queued bufs, etc) and set the new config. */
-+ raise_exception(fsg, FSG_STATE_CONFIG_CHANGE);
-+ value = DELAYED_STATUS;
-+ }
-+ break;
-+ case USB_REQ_GET_CONFIGURATION:
-+ if (ctrl->bRequestType != (USB_DIR_IN | USB_TYPE_STANDARD |
-+ USB_RECIP_DEVICE))
-+ break;
-+ VDBG(fsg, "get configuration\n");
-+ *(u8 *) req->buf = fsg->config;
-+ value = 1;
-+ break;
-+
-+ case USB_REQ_SET_INTERFACE:
-+ if (ctrl->bRequestType != (USB_DIR_OUT| USB_TYPE_STANDARD |
-+ USB_RECIP_INTERFACE))
-+ break;
-+ if (fsg->config && w_index == 0) {
-+
-+ /* Raise an exception to wipe out previous transaction
-+ * state (queued bufs, etc) and install the new
-+ * interface altsetting. */
-+ raise_exception(fsg, FSG_STATE_INTERFACE_CHANGE);
-+ value = DELAYED_STATUS;
-+ }
-+ break;
-+ case USB_REQ_GET_INTERFACE:
-+ if (ctrl->bRequestType != (USB_DIR_IN | USB_TYPE_STANDARD |
-+ USB_RECIP_INTERFACE))
-+ break;
-+ if (!fsg->config)
-+ break;
-+ if (w_index != 0) {
-+ value = -EDOM;
-+ break;
-+ }
-+ VDBG(fsg, "get interface\n");
-+ *(u8 *) req->buf = 0;
-+ value = 1;
-+ break;
-+
-+ default:
-+ VDBG(fsg,
-+ "unknown control req %02x.%02x v%04x i%04x l%u\n",
-+ ctrl->bRequestType, ctrl->bRequest,
-+ w_value, w_index, le16_to_cpu(ctrl->wLength));
-+ }
-+
-+ return value;
-+}
-+
-+
-+static int fsg_setup(struct usb_gadget *gadget,
-+ const struct usb_ctrlrequest *ctrl)
-+{
-+ struct fsg_dev *fsg = get_gadget_data(gadget);
-+ int rc;
-+ int w_length = le16_to_cpu(ctrl->wLength);
-+
-+ ++fsg->ep0_req_tag; // Record arrival of a new request
-+ fsg->ep0req->context = NULL;
-+ fsg->ep0req->length = 0;
-+ dump_msg(fsg, "ep0-setup", (u8 *) ctrl, sizeof(*ctrl));
-+
-+ if ((ctrl->bRequestType & USB_TYPE_MASK) == USB_TYPE_CLASS)
-+ rc = class_setup_req(fsg, ctrl);
-+ else
-+ rc = standard_setup_req(fsg, ctrl);
-+
-+ /* Respond with data/status or defer until later? */
-+ if (rc >= 0 && rc != DELAYED_STATUS) {
-+ rc = min(rc, w_length);
-+ fsg->ep0req->length = rc;
-+ fsg->ep0req->zero = rc < w_length;
-+ fsg->ep0req_name = (ctrl->bRequestType & USB_DIR_IN ?
-+ "ep0-in" : "ep0-out");
-+ rc = ep0_queue(fsg);
-+ }
-+
-+ /* Device either stalls (rc < 0) or reports success */
-+ return rc;
-+}
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+/* All the following routines run in process context */
-+
-+
-+/* Use this for bulk or interrupt transfers, not ep0 */
-+static void start_transfer(struct fsg_dev *fsg, struct usb_ep *ep,
-+ struct usb_request *req, int *pbusy,
-+ enum fsg_buffer_state *state)
-+{
-+ int rc;
-+
-+ if (ep == fsg->bulk_in)
-+ dump_msg(fsg, "bulk-in", req->buf, req->length);
-+ else if (ep == fsg->intr_in)
-+ dump_msg(fsg, "intr-in", req->buf, req->length);
-+
-+ spin_lock_irq(&fsg->lock);
-+ *pbusy = 1;
-+ *state = BUF_STATE_BUSY;
-+ spin_unlock_irq(&fsg->lock);
-+ rc = usb_ep_queue(ep, req, GFP_KERNEL);
-+ if (rc != 0) {
-+ *pbusy = 0;
-+ *state = BUF_STATE_EMPTY;
-+
-+ /* We can't do much more than wait for a reset */
-+
-+ /* Note: currently the net2280 driver fails zero-length
-+ * submissions if DMA is enabled. */
-+ if (rc != -ESHUTDOWN && !(rc == -EOPNOTSUPP &&
-+ req->length == 0))
-+ WARNING(fsg, "error in submission: %s --> %d\n",
-+ ep->name, rc);
-+ }
-+}
-+
-+
-+static int sleep_thread(struct fsg_dev *fsg)
-+{
-+ int rc = 0;
-+
-+ /* Wait until a signal arrives or we are woken up */
-+ for (;;) {
-+ try_to_freeze();
-+ set_current_state(TASK_INTERRUPTIBLE);
-+ if (signal_pending(current)) {
-+ rc = -EINTR;
-+ break;
-+ }
-+ if (fsg->thread_wakeup_needed)
-+ break;
-+ schedule();
-+ }
-+ __set_current_state(TASK_RUNNING);
-+ fsg->thread_wakeup_needed = 0;
-+ return rc;
-+}
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+static int do_read(struct fsg_dev *fsg)
-+{
-+ struct fsg_lun *curlun = fsg->curlun;
-+ u32 lba;
-+ struct fsg_buffhd *bh;
-+ int rc;
-+ u32 amount_left;
-+ loff_t file_offset, file_offset_tmp;
-+ unsigned int amount;
-+ ssize_t nread;
-+
-+ /* Get the starting Logical Block Address and check that it's
-+ * not too big */
-+ if (fsg->cmnd[0] == READ_6)
-+ lba = get_unaligned_be24(&fsg->cmnd[1]);
-+ else {
-+ lba = get_unaligned_be32(&fsg->cmnd[2]);
-+
-+ /* We allow DPO (Disable Page Out = don't save data in the
-+ * cache) and FUA (Force Unit Access = don't read from the
-+ * cache), but we don't implement them. */
-+ if ((fsg->cmnd[1] & ~0x18) != 0) {
-+ curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
-+ return -EINVAL;
-+ }
-+ }
-+ if (lba >= curlun->num_sectors) {
-+ curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
-+ return -EINVAL;
-+ }
-+ file_offset = ((loff_t) lba) << curlun->blkbits;
-+
-+ /* Carry out the file reads */
-+ amount_left = fsg->data_size_from_cmnd;
-+ if (unlikely(amount_left == 0))
-+ return -EIO; // No default reply
-+
-+ for (;;) {
-+
-+ /* Figure out how much we need to read:
-+ * Try to read the remaining amount.
-+ * But don't read more than the buffer size.
-+ * And don't try to read past the end of the file.
-+ */
-+ amount = min((unsigned int) amount_left, mod_data.buflen);
-+ amount = min((loff_t) amount,
-+ curlun->file_length - file_offset);
-+
-+ /* Wait for the next buffer to become available */
-+ bh = fsg->next_buffhd_to_fill;
-+ while (bh->state != BUF_STATE_EMPTY) {
-+ rc = sleep_thread(fsg);
-+ if (rc)
-+ return rc;
-+ }
-+
-+ /* If we were asked to read past the end of file,
-+ * end with an empty buffer. */
-+ if (amount == 0) {
-+ curlun->sense_data =
-+ SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
-+ curlun->sense_data_info = file_offset >> curlun->blkbits;
-+ curlun->info_valid = 1;
-+ bh->inreq->length = 0;
-+ bh->state = BUF_STATE_FULL;
-+ break;
-+ }
-+
-+ /* Perform the read */
-+ file_offset_tmp = file_offset;
-+ nread = vfs_read(curlun->filp,
-+ (char __user *) bh->buf,
-+ amount, &file_offset_tmp);
-+ VLDBG(curlun, "file read %u @ %llu -> %d\n", amount,
-+ (unsigned long long) file_offset,
-+ (int) nread);
-+ if (signal_pending(current))
-+ return -EINTR;
-+
-+ if (nread < 0) {
-+ LDBG(curlun, "error in file read: %d\n",
-+ (int) nread);
-+ nread = 0;
-+ } else if (nread < amount) {
-+ LDBG(curlun, "partial file read: %d/%u\n",
-+ (int) nread, amount);
-+ nread = round_down(nread, curlun->blksize);
-+ }
-+ file_offset += nread;
-+ amount_left -= nread;
-+ fsg->residue -= nread;
-+
-+ /* Except at the end of the transfer, nread will be
-+ * equal to the buffer size, which is divisible by the
-+ * bulk-in maxpacket size.
-+ */
-+ bh->inreq->length = nread;
-+ bh->state = BUF_STATE_FULL;
-+
-+ /* If an error occurred, report it and its position */
-+ if (nread < amount) {
-+ curlun->sense_data = SS_UNRECOVERED_READ_ERROR;
-+ curlun->sense_data_info = file_offset >> curlun->blkbits;
-+ curlun->info_valid = 1;
-+ break;
-+ }
-+
-+ if (amount_left == 0)
-+ break; // No more left to read
-+
-+ /* Send this buffer and go read some more */
-+ bh->inreq->zero = 0;
-+ start_transfer(fsg, fsg->bulk_in, bh->inreq,
-+ &bh->inreq_busy, &bh->state);
-+ fsg->next_buffhd_to_fill = bh->next;
-+ }
-+
-+ return -EIO; // No default reply
-+}
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+static int do_write(struct fsg_dev *fsg)
-+{
-+ struct fsg_lun *curlun = fsg->curlun;
-+ u32 lba;
-+ struct fsg_buffhd *bh;
-+ int get_some_more;
-+ u32 amount_left_to_req, amount_left_to_write;
-+ loff_t usb_offset, file_offset, file_offset_tmp;
-+ unsigned int amount;
-+ ssize_t nwritten;
-+ int rc;
-+
-+ if (curlun->ro) {
-+ curlun->sense_data = SS_WRITE_PROTECTED;
-+ return -EINVAL;
-+ }
-+ spin_lock(&curlun->filp->f_lock);
-+ curlun->filp->f_flags &= ~O_SYNC; // Default is not to wait
-+ spin_unlock(&curlun->filp->f_lock);
-+
-+ /* Get the starting Logical Block Address and check that it's
-+ * not too big */
-+ if (fsg->cmnd[0] == WRITE_6)
-+ lba = get_unaligned_be24(&fsg->cmnd[1]);
-+ else {
-+ lba = get_unaligned_be32(&fsg->cmnd[2]);
-+
-+ /* We allow DPO (Disable Page Out = don't save data in the
-+ * cache) and FUA (Force Unit Access = write directly to the
-+ * medium). We don't implement DPO; we implement FUA by
-+ * performing synchronous output. */
-+ if ((fsg->cmnd[1] & ~0x18) != 0) {
-+ curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
-+ return -EINVAL;
-+ }
-+ /* FUA */
-+ if (!curlun->nofua && (fsg->cmnd[1] & 0x08)) {
-+ spin_lock(&curlun->filp->f_lock);
-+ curlun->filp->f_flags |= O_DSYNC;
-+ spin_unlock(&curlun->filp->f_lock);
-+ }
-+ }
-+ if (lba >= curlun->num_sectors) {
-+ curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
-+ return -EINVAL;
-+ }
-+
-+ /* Carry out the file writes */
-+ get_some_more = 1;
-+ file_offset = usb_offset = ((loff_t) lba) << curlun->blkbits;
-+ amount_left_to_req = amount_left_to_write = fsg->data_size_from_cmnd;
-+
-+ while (amount_left_to_write > 0) {
-+
-+ /* Queue a request for more data from the host */
-+ bh = fsg->next_buffhd_to_fill;
-+ if (bh->state == BUF_STATE_EMPTY && get_some_more) {
-+
-+ /* Figure out how much we want to get:
-+ * Try to get the remaining amount,
-+ * but not more than the buffer size.
-+ */
-+ amount = min(amount_left_to_req, mod_data.buflen);
-+
-+ /* Beyond the end of the backing file? */
-+ if (usb_offset >= curlun->file_length) {
-+ get_some_more = 0;
-+ curlun->sense_data =
-+ SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
-+ curlun->sense_data_info = usb_offset >> curlun->blkbits;
-+ curlun->info_valid = 1;
-+ continue;
-+ }
-+
-+ /* Get the next buffer */
-+ usb_offset += amount;
-+ fsg->usb_amount_left -= amount;
-+ amount_left_to_req -= amount;
-+ if (amount_left_to_req == 0)
-+ get_some_more = 0;
-+
-+ /* Except at the end of the transfer, amount will be
-+ * equal to the buffer size, which is divisible by
-+ * the bulk-out maxpacket size.
-+ */
-+ set_bulk_out_req_length(fsg, bh, amount);
-+ start_transfer(fsg, fsg->bulk_out, bh->outreq,
-+ &bh->outreq_busy, &bh->state);
-+ fsg->next_buffhd_to_fill = bh->next;
-+ continue;
-+ }
-+
-+ /* Write the received data to the backing file */
-+ bh = fsg->next_buffhd_to_drain;
-+ if (bh->state == BUF_STATE_EMPTY && !get_some_more)
-+ break; // We stopped early
-+ if (bh->state == BUF_STATE_FULL) {
-+ smp_rmb();
-+ fsg->next_buffhd_to_drain = bh->next;
-+ bh->state = BUF_STATE_EMPTY;
-+
-+ /* Did something go wrong with the transfer? */
-+ if (bh->outreq->status != 0) {
-+ curlun->sense_data = SS_COMMUNICATION_FAILURE;
-+ curlun->sense_data_info = file_offset >> curlun->blkbits;
-+ curlun->info_valid = 1;
-+ break;
-+ }
-+
-+ amount = bh->outreq->actual;
-+ if (curlun->file_length - file_offset < amount) {
-+ LERROR(curlun,
-+ "write %u @ %llu beyond end %llu\n",
-+ amount, (unsigned long long) file_offset,
-+ (unsigned long long) curlun->file_length);
-+ amount = curlun->file_length - file_offset;
-+ }
-+
-+ /* Don't accept excess data. The spec doesn't say
-+ * what to do in this case. We'll ignore the error.
-+ */
-+ amount = min(amount, bh->bulk_out_intended_length);
-+
-+ /* Don't write a partial block */
-+ amount = round_down(amount, curlun->blksize);
-+ if (amount == 0)
-+ goto empty_write;
-+
-+ /* Perform the write */
-+ file_offset_tmp = file_offset;
-+ nwritten = vfs_write(curlun->filp,
-+ (char __user *) bh->buf,
-+ amount, &file_offset_tmp);
-+ VLDBG(curlun, "file write %u @ %llu -> %d\n", amount,
-+ (unsigned long long) file_offset,
-+ (int) nwritten);
-+ if (signal_pending(current))
-+ return -EINTR; // Interrupted!
-+
-+ if (nwritten < 0) {
-+ LDBG(curlun, "error in file write: %d\n",
-+ (int) nwritten);
-+ nwritten = 0;
-+ } else if (nwritten < amount) {
-+ LDBG(curlun, "partial file write: %d/%u\n",
-+ (int) nwritten, amount);
-+ nwritten = round_down(nwritten, curlun->blksize);
-+ }
-+ file_offset += nwritten;
-+ amount_left_to_write -= nwritten;
-+ fsg->residue -= nwritten;
-+
-+ /* If an error occurred, report it and its position */
-+ if (nwritten < amount) {
-+ curlun->sense_data = SS_WRITE_ERROR;
-+ curlun->sense_data_info = file_offset >> curlun->blkbits;
-+ curlun->info_valid = 1;
-+ break;
-+ }
-+
-+ empty_write:
-+ /* Did the host decide to stop early? */
-+ if (bh->outreq->actual < bh->bulk_out_intended_length) {
-+ fsg->short_packet_received = 1;
-+ break;
-+ }
-+ continue;
-+ }
-+
-+ /* Wait for something to happen */
-+ rc = sleep_thread(fsg);
-+ if (rc)
-+ return rc;
-+ }
-+
-+ return -EIO; // No default reply
-+}
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+static int do_synchronize_cache(struct fsg_dev *fsg)
-+{
-+ struct fsg_lun *curlun = fsg->curlun;
-+ int rc;
-+
-+ /* We ignore the requested LBA and write out all file's
-+ * dirty data buffers. */
-+ rc = fsg_lun_fsync_sub(curlun);
-+ if (rc)
-+ curlun->sense_data = SS_WRITE_ERROR;
-+ return 0;
-+}
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+static void invalidate_sub(struct fsg_lun *curlun)
-+{
-+ struct file *filp = curlun->filp;
-+ struct inode *inode = filp->f_path.dentry->d_inode;
-+ unsigned long rc;
-+
-+ rc = invalidate_mapping_pages(inode->i_mapping, 0, -1);
-+ VLDBG(curlun, "invalidate_mapping_pages -> %ld\n", rc);
-+}
-+
-+static int do_verify(struct fsg_dev *fsg)
-+{
-+ struct fsg_lun *curlun = fsg->curlun;
-+ u32 lba;
-+ u32 verification_length;
-+ struct fsg_buffhd *bh = fsg->next_buffhd_to_fill;
-+ loff_t file_offset, file_offset_tmp;
-+ u32 amount_left;
-+ unsigned int amount;
-+ ssize_t nread;
-+
-+ /* Get the starting Logical Block Address and check that it's
-+ * not too big */
-+ lba = get_unaligned_be32(&fsg->cmnd[2]);
-+ if (lba >= curlun->num_sectors) {
-+ curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
-+ return -EINVAL;
-+ }
-+
-+ /* We allow DPO (Disable Page Out = don't save data in the
-+ * cache) but we don't implement it. */
-+ if ((fsg->cmnd[1] & ~0x10) != 0) {
-+ curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
-+ return -EINVAL;
-+ }
-+
-+ verification_length = get_unaligned_be16(&fsg->cmnd[7]);
-+ if (unlikely(verification_length == 0))
-+ return -EIO; // No default reply
-+
-+ /* Prepare to carry out the file verify */
-+ amount_left = verification_length << curlun->blkbits;
-+ file_offset = ((loff_t) lba) << curlun->blkbits;
-+
-+ /* Write out all the dirty buffers before invalidating them */
-+ fsg_lun_fsync_sub(curlun);
-+ if (signal_pending(current))
-+ return -EINTR;
-+
-+ invalidate_sub(curlun);
-+ if (signal_pending(current))
-+ return -EINTR;
-+
-+ /* Just try to read the requested blocks */
-+ while (amount_left > 0) {
-+
-+ /* Figure out how much we need to read:
-+ * Try to read the remaining amount, but not more than
-+ * the buffer size.
-+ * And don't try to read past the end of the file.
-+ */
-+ amount = min((unsigned int) amount_left, mod_data.buflen);
-+ amount = min((loff_t) amount,
-+ curlun->file_length - file_offset);
-+ if (amount == 0) {
-+ curlun->sense_data =
-+ SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
-+ curlun->sense_data_info = file_offset >> curlun->blkbits;
-+ curlun->info_valid = 1;
-+ break;
-+ }
-+
-+ /* Perform the read */
-+ file_offset_tmp = file_offset;
-+ nread = vfs_read(curlun->filp,
-+ (char __user *) bh->buf,
-+ amount, &file_offset_tmp);
-+ VLDBG(curlun, "file read %u @ %llu -> %d\n", amount,
-+ (unsigned long long) file_offset,
-+ (int) nread);
-+ if (signal_pending(current))
-+ return -EINTR;
-+
-+ if (nread < 0) {
-+ LDBG(curlun, "error in file verify: %d\n",
-+ (int) nread);
-+ nread = 0;
-+ } else if (nread < amount) {
-+ LDBG(curlun, "partial file verify: %d/%u\n",
-+ (int) nread, amount);
-+ nread = round_down(nread, curlun->blksize);
-+ }
-+ if (nread == 0) {
-+ curlun->sense_data = SS_UNRECOVERED_READ_ERROR;
-+ curlun->sense_data_info = file_offset >> curlun->blkbits;
-+ curlun->info_valid = 1;
-+ break;
-+ }
-+ file_offset += nread;
-+ amount_left -= nread;
-+ }
-+ return 0;
-+}
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+static int do_inquiry(struct fsg_dev *fsg, struct fsg_buffhd *bh)
-+{
-+ u8 *buf = (u8 *) bh->buf;
-+
-+ static char vendor_id[] = "Linux ";
-+ static char product_disk_id[] = "File-Stor Gadget";
-+ static char product_cdrom_id[] = "File-CD Gadget ";
-+
-+ if (!fsg->curlun) { // Unsupported LUNs are okay
-+ fsg->bad_lun_okay = 1;
-+ memset(buf, 0, 36);
-+ buf[0] = 0x7f; // Unsupported, no device-type
-+ buf[4] = 31; // Additional length
-+ return 36;
-+ }
-+
-+ memset(buf, 0, 8);
-+ buf[0] = (mod_data.cdrom ? TYPE_ROM : TYPE_DISK);
-+ if (mod_data.removable)
-+ buf[1] = 0x80;
-+ buf[2] = 2; // ANSI SCSI level 2
-+ buf[3] = 2; // SCSI-2 INQUIRY data format
-+ buf[4] = 31; // Additional length
-+ // No special options
-+ sprintf(buf + 8, "%-8s%-16s%04x", vendor_id,
-+ (mod_data.cdrom ? product_cdrom_id :
-+ product_disk_id),
-+ mod_data.release);
-+ return 36;
-+}
-+
-+
-+static int do_request_sense(struct fsg_dev *fsg, struct fsg_buffhd *bh)
-+{
-+ struct fsg_lun *curlun = fsg->curlun;
-+ u8 *buf = (u8 *) bh->buf;
-+ u32 sd, sdinfo;
-+ int valid;
-+
-+ /*
-+ * From the SCSI-2 spec., section 7.9 (Unit attention condition):
-+ *
-+ * If a REQUEST SENSE command is received from an initiator
-+ * with a pending unit attention condition (before the target
-+ * generates the contingent allegiance condition), then the
-+ * target shall either:
-+ * a) report any pending sense data and preserve the unit
-+ * attention condition on the logical unit, or,
-+ * b) report the unit attention condition, may discard any
-+ * pending sense data, and clear the unit attention
-+ * condition on the logical unit for that initiator.
-+ *
-+ * FSG normally uses option a); enable this code to use option b).
-+ */
-+#if 0
-+ if (curlun && curlun->unit_attention_data != SS_NO_SENSE) {
-+ curlun->sense_data = curlun->unit_attention_data;
-+ curlun->unit_attention_data = SS_NO_SENSE;
-+ }
-+#endif
-+
-+ if (!curlun) { // Unsupported LUNs are okay
-+ fsg->bad_lun_okay = 1;
-+ sd = SS_LOGICAL_UNIT_NOT_SUPPORTED;
-+ sdinfo = 0;
-+ valid = 0;
-+ } else {
-+ sd = curlun->sense_data;
-+ sdinfo = curlun->sense_data_info;
-+ valid = curlun->info_valid << 7;
-+ curlun->sense_data = SS_NO_SENSE;
-+ curlun->sense_data_info = 0;
-+ curlun->info_valid = 0;
-+ }
-+
-+ memset(buf, 0, 18);
-+ buf[0] = valid | 0x70; // Valid, current error
-+ buf[2] = SK(sd);
-+ put_unaligned_be32(sdinfo, &buf[3]); /* Sense information */
-+ buf[7] = 18 - 8; // Additional sense length
-+ buf[12] = ASC(sd);
-+ buf[13] = ASCQ(sd);
-+ return 18;
-+}
-+
-+
-+static int do_read_capacity(struct fsg_dev *fsg, struct fsg_buffhd *bh)
-+{
-+ struct fsg_lun *curlun = fsg->curlun;
-+ u32 lba = get_unaligned_be32(&fsg->cmnd[2]);
-+ int pmi = fsg->cmnd[8];
-+ u8 *buf = (u8 *) bh->buf;
-+
-+ /* Check the PMI and LBA fields */
-+ if (pmi > 1 || (pmi == 0 && lba != 0)) {
-+ curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
-+ return -EINVAL;
-+ }
-+
-+ put_unaligned_be32(curlun->num_sectors - 1, &buf[0]);
-+ /* Max logical block */
-+ put_unaligned_be32(curlun->blksize, &buf[4]); /* Block length */
-+ return 8;
-+}
-+
-+
-+static int do_read_header(struct fsg_dev *fsg, struct fsg_buffhd *bh)
-+{
-+ struct fsg_lun *curlun = fsg->curlun;
-+ int msf = fsg->cmnd[1] & 0x02;
-+ u32 lba = get_unaligned_be32(&fsg->cmnd[2]);
-+ u8 *buf = (u8 *) bh->buf;
-+
-+ if ((fsg->cmnd[1] & ~0x02) != 0) { /* Mask away MSF */
-+ curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
-+ return -EINVAL;
-+ }
-+ if (lba >= curlun->num_sectors) {
-+ curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
-+ return -EINVAL;
-+ }
-+
-+ memset(buf, 0, 8);
-+ buf[0] = 0x01; /* 2048 bytes of user data, rest is EC */
-+ store_cdrom_address(&buf[4], msf, lba);
-+ return 8;
-+}
-+
-+
-+static int do_read_toc(struct fsg_dev *fsg, struct fsg_buffhd *bh)
-+{
-+ struct fsg_lun *curlun = fsg->curlun;
-+ int msf = fsg->cmnd[1] & 0x02;
-+ int start_track = fsg->cmnd[6];
-+ u8 *buf = (u8 *) bh->buf;
-+
-+ if ((fsg->cmnd[1] & ~0x02) != 0 || /* Mask away MSF */
-+ start_track > 1) {
-+ curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
-+ return -EINVAL;
-+ }
-+
-+ memset(buf, 0, 20);
-+ buf[1] = (20-2); /* TOC data length */
-+ buf[2] = 1; /* First track number */
-+ buf[3] = 1; /* Last track number */
-+ buf[5] = 0x16; /* Data track, copying allowed */
-+ buf[6] = 0x01; /* Only track is number 1 */
-+ store_cdrom_address(&buf[8], msf, 0);
-+
-+ buf[13] = 0x16; /* Lead-out track is data */
-+ buf[14] = 0xAA; /* Lead-out track number */
-+ store_cdrom_address(&buf[16], msf, curlun->num_sectors);
-+ return 20;
-+}
-+
-+
-+static int do_mode_sense(struct fsg_dev *fsg, struct fsg_buffhd *bh)
-+{
-+ struct fsg_lun *curlun = fsg->curlun;
-+ int mscmnd = fsg->cmnd[0];
-+ u8 *buf = (u8 *) bh->buf;
-+ u8 *buf0 = buf;
-+ int pc, page_code;
-+ int changeable_values, all_pages;
-+ int valid_page = 0;
-+ int len, limit;
-+
-+ if ((fsg->cmnd[1] & ~0x08) != 0) { // Mask away DBD
-+ curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
-+ return -EINVAL;
-+ }
-+ pc = fsg->cmnd[2] >> 6;
-+ page_code = fsg->cmnd[2] & 0x3f;
-+ if (pc == 3) {
-+ curlun->sense_data = SS_SAVING_PARAMETERS_NOT_SUPPORTED;
-+ return -EINVAL;
-+ }
-+ changeable_values = (pc == 1);
-+ all_pages = (page_code == 0x3f);
-+
-+ /* Write the mode parameter header. Fixed values are: default
-+ * medium type, no cache control (DPOFUA), and no block descriptors.
-+ * The only variable value is the WriteProtect bit. We will fill in
-+ * the mode data length later. */
-+ memset(buf, 0, 8);
-+ if (mscmnd == MODE_SENSE) {
-+ buf[2] = (curlun->ro ? 0x80 : 0x00); // WP, DPOFUA
-+ buf += 4;
-+ limit = 255;
-+ } else { // MODE_SENSE_10
-+ buf[3] = (curlun->ro ? 0x80 : 0x00); // WP, DPOFUA
-+ buf += 8;
-+ limit = 65535; // Should really be mod_data.buflen
-+ }
-+
-+ /* No block descriptors */
-+
-+ /* The mode pages, in numerical order. The only page we support
-+ * is the Caching page. */
-+ if (page_code == 0x08 || all_pages) {
-+ valid_page = 1;
-+ buf[0] = 0x08; // Page code
-+ buf[1] = 10; // Page length
-+ memset(buf+2, 0, 10); // None of the fields are changeable
-+
-+ if (!changeable_values) {
-+ buf[2] = 0x04; // Write cache enable,
-+ // Read cache not disabled
-+ // No cache retention priorities
-+ put_unaligned_be16(0xffff, &buf[4]);
-+ /* Don't disable prefetch */
-+ /* Minimum prefetch = 0 */
-+ put_unaligned_be16(0xffff, &buf[8]);
-+ /* Maximum prefetch */
-+ put_unaligned_be16(0xffff, &buf[10]);
-+ /* Maximum prefetch ceiling */
-+ }
-+ buf += 12;
-+ }
-+
-+ /* Check that a valid page was requested and the mode data length
-+ * isn't too long. */
-+ len = buf - buf0;
-+ if (!valid_page || len > limit) {
-+ curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
-+ return -EINVAL;
-+ }
-+
-+ /* Store the mode data length */
-+ if (mscmnd == MODE_SENSE)
-+ buf0[0] = len - 1;
-+ else
-+ put_unaligned_be16(len - 2, buf0);
-+ return len;
-+}
-+
-+
-+static int do_start_stop(struct fsg_dev *fsg)
-+{
-+ struct fsg_lun *curlun = fsg->curlun;
-+ int loej, start;
-+
-+ if (!mod_data.removable) {
-+ curlun->sense_data = SS_INVALID_COMMAND;
-+ return -EINVAL;
-+ }
-+
-+ // int immed = fsg->cmnd[1] & 0x01;
-+ loej = fsg->cmnd[4] & 0x02;
-+ start = fsg->cmnd[4] & 0x01;
-+
-+#ifdef CONFIG_USB_FILE_STORAGE_TEST
-+ if ((fsg->cmnd[1] & ~0x01) != 0 || // Mask away Immed
-+ (fsg->cmnd[4] & ~0x03) != 0) { // Mask LoEj, Start
-+ curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
-+ return -EINVAL;
-+ }
-+
-+ if (!start) {
-+
-+ /* Are we allowed to unload the media? */
-+ if (curlun->prevent_medium_removal) {
-+ LDBG(curlun, "unload attempt prevented\n");
-+ curlun->sense_data = SS_MEDIUM_REMOVAL_PREVENTED;
-+ return -EINVAL;
-+ }
-+ if (loej) { // Simulate an unload/eject
-+ up_read(&fsg->filesem);
-+ down_write(&fsg->filesem);
-+ fsg_lun_close(curlun);
-+ up_write(&fsg->filesem);
-+ down_read(&fsg->filesem);
-+ }
-+ } else {
-+
-+ /* Our emulation doesn't support mounting; the medium is
-+ * available for use as soon as it is loaded. */
-+ if (!fsg_lun_is_open(curlun)) {
-+ curlun->sense_data = SS_MEDIUM_NOT_PRESENT;
-+ return -EINVAL;
-+ }
-+ }
-+#endif
-+ return 0;
-+}
-+
-+
-+static int do_prevent_allow(struct fsg_dev *fsg)
-+{
-+ struct fsg_lun *curlun = fsg->curlun;
-+ int prevent;
-+
-+ if (!mod_data.removable) {
-+ curlun->sense_data = SS_INVALID_COMMAND;
-+ return -EINVAL;
-+ }
-+
-+ prevent = fsg->cmnd[4] & 0x01;
-+ if ((fsg->cmnd[4] & ~0x01) != 0) { // Mask away Prevent
-+ curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
-+ return -EINVAL;
-+ }
-+
-+ if (curlun->prevent_medium_removal && !prevent)
-+ fsg_lun_fsync_sub(curlun);
-+ curlun->prevent_medium_removal = prevent;
-+ return 0;
-+}
-+
-+
-+static int do_read_format_capacities(struct fsg_dev *fsg,
-+ struct fsg_buffhd *bh)
-+{
-+ struct fsg_lun *curlun = fsg->curlun;
-+ u8 *buf = (u8 *) bh->buf;
-+
-+ buf[0] = buf[1] = buf[2] = 0;
-+ buf[3] = 8; // Only the Current/Maximum Capacity Descriptor
-+ buf += 4;
-+
-+ put_unaligned_be32(curlun->num_sectors, &buf[0]);
-+ /* Number of blocks */
-+ put_unaligned_be32(curlun->blksize, &buf[4]); /* Block length */
-+ buf[4] = 0x02; /* Current capacity */
-+ return 12;
-+}
-+
-+
-+static int do_mode_select(struct fsg_dev *fsg, struct fsg_buffhd *bh)
-+{
-+ struct fsg_lun *curlun = fsg->curlun;
-+
-+ /* We don't support MODE SELECT */
-+ curlun->sense_data = SS_INVALID_COMMAND;
-+ return -EINVAL;
-+}
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+static int halt_bulk_in_endpoint(struct fsg_dev *fsg)
-+{
-+ int rc;
-+
-+ rc = fsg_set_halt(fsg, fsg->bulk_in);
-+ if (rc == -EAGAIN)
-+ VDBG(fsg, "delayed bulk-in endpoint halt\n");
-+ while (rc != 0) {
-+ if (rc != -EAGAIN) {
-+ WARNING(fsg, "usb_ep_set_halt -> %d\n", rc);
-+ rc = 0;
-+ break;
-+ }
-+
-+ /* Wait for a short time and then try again */
-+ if (msleep_interruptible(100) != 0)
-+ return -EINTR;
-+ rc = usb_ep_set_halt(fsg->bulk_in);
-+ }
-+ return rc;
-+}
-+
-+static int wedge_bulk_in_endpoint(struct fsg_dev *fsg)
-+{
-+ int rc;
-+
-+ DBG(fsg, "bulk-in set wedge\n");
-+ rc = usb_ep_set_wedge(fsg->bulk_in);
-+ if (rc == -EAGAIN)
-+ VDBG(fsg, "delayed bulk-in endpoint wedge\n");
-+ while (rc != 0) {
-+ if (rc != -EAGAIN) {
-+ WARNING(fsg, "usb_ep_set_wedge -> %d\n", rc);
-+ rc = 0;
-+ break;
-+ }
-+
-+ /* Wait for a short time and then try again */
-+ if (msleep_interruptible(100) != 0)
-+ return -EINTR;
-+ rc = usb_ep_set_wedge(fsg->bulk_in);
-+ }
-+ return rc;
-+}
-+
-+static int throw_away_data(struct fsg_dev *fsg)
-+{
-+ struct fsg_buffhd *bh;
-+ u32 amount;
-+ int rc;
-+
-+ while ((bh = fsg->next_buffhd_to_drain)->state != BUF_STATE_EMPTY ||
-+ fsg->usb_amount_left > 0) {
-+
-+ /* Throw away the data in a filled buffer */
-+ if (bh->state == BUF_STATE_FULL) {
-+ smp_rmb();
-+ bh->state = BUF_STATE_EMPTY;
-+ fsg->next_buffhd_to_drain = bh->next;
-+
-+ /* A short packet or an error ends everything */
-+ if (bh->outreq->actual < bh->bulk_out_intended_length ||
-+ bh->outreq->status != 0) {
-+ raise_exception(fsg, FSG_STATE_ABORT_BULK_OUT);
-+ return -EINTR;
-+ }
-+ continue;
-+ }
-+
-+ /* Try to submit another request if we need one */
-+ bh = fsg->next_buffhd_to_fill;
-+ if (bh->state == BUF_STATE_EMPTY && fsg->usb_amount_left > 0) {
-+ amount = min(fsg->usb_amount_left,
-+ (u32) mod_data.buflen);
-+
-+ /* Except at the end of the transfer, amount will be
-+ * equal to the buffer size, which is divisible by
-+ * the bulk-out maxpacket size.
-+ */
-+ set_bulk_out_req_length(fsg, bh, amount);
-+ start_transfer(fsg, fsg->bulk_out, bh->outreq,
-+ &bh->outreq_busy, &bh->state);
-+ fsg->next_buffhd_to_fill = bh->next;
-+ fsg->usb_amount_left -= amount;
-+ continue;
-+ }
-+
-+ /* Otherwise wait for something to happen */
-+ rc = sleep_thread(fsg);
-+ if (rc)
-+ return rc;
-+ }
-+ return 0;
-+}
-+
-+
-+static int finish_reply(struct fsg_dev *fsg)
-+{
-+ struct fsg_buffhd *bh = fsg->next_buffhd_to_fill;
-+ int rc = 0;
-+
-+ switch (fsg->data_dir) {
-+ case DATA_DIR_NONE:
-+ break; // Nothing to send
-+
-+ /* If we don't know whether the host wants to read or write,
-+ * this must be CB or CBI with an unknown command. We mustn't
-+ * try to send or receive any data. So stall both bulk pipes
-+ * if we can and wait for a reset. */
-+ case DATA_DIR_UNKNOWN:
-+ if (mod_data.can_stall) {
-+ fsg_set_halt(fsg, fsg->bulk_out);
-+ rc = halt_bulk_in_endpoint(fsg);
-+ }
-+ break;
-+
-+ /* All but the last buffer of data must have already been sent */
-+ case DATA_DIR_TO_HOST:
-+ if (fsg->data_size == 0)
-+ ; // Nothing to send
-+
-+ /* If there's no residue, simply send the last buffer */
-+ else if (fsg->residue == 0) {
-+ bh->inreq->zero = 0;
-+ start_transfer(fsg, fsg->bulk_in, bh->inreq,
-+ &bh->inreq_busy, &bh->state);
-+ fsg->next_buffhd_to_fill = bh->next;
-+ }
-+
-+ /* There is a residue. For CB and CBI, simply mark the end
-+ * of the data with a short packet. However, if we are
-+ * allowed to stall, there was no data at all (residue ==
-+ * data_size), and the command failed (invalid LUN or
-+ * sense data is set), then halt the bulk-in endpoint
-+ * instead. */
-+ else if (!transport_is_bbb()) {
-+ if (mod_data.can_stall &&
-+ fsg->residue == fsg->data_size &&
-+ (!fsg->curlun || fsg->curlun->sense_data != SS_NO_SENSE)) {
-+ bh->state = BUF_STATE_EMPTY;
-+ rc = halt_bulk_in_endpoint(fsg);
-+ } else {
-+ bh->inreq->zero = 1;
-+ start_transfer(fsg, fsg->bulk_in, bh->inreq,
-+ &bh->inreq_busy, &bh->state);
-+ fsg->next_buffhd_to_fill = bh->next;
-+ }
-+ }
-+
-+ /*
-+ * For Bulk-only, mark the end of the data with a short
-+ * packet. If we are allowed to stall, halt the bulk-in
-+ * endpoint. (Note: This violates the Bulk-Only Transport
-+ * specification, which requires us to pad the data if we
-+ * don't halt the endpoint. Presumably nobody will mind.)
-+ */
-+ else {
-+ bh->inreq->zero = 1;
-+ start_transfer(fsg, fsg->bulk_in, bh->inreq,
-+ &bh->inreq_busy, &bh->state);
-+ fsg->next_buffhd_to_fill = bh->next;
-+ if (mod_data.can_stall)
-+ rc = halt_bulk_in_endpoint(fsg);
-+ }
-+ break;
-+
-+ /* We have processed all we want from the data the host has sent.
-+ * There may still be outstanding bulk-out requests. */
-+ case DATA_DIR_FROM_HOST:
-+ if (fsg->residue == 0)
-+ ; // Nothing to receive
-+
-+ /* Did the host stop sending unexpectedly early? */
-+ else if (fsg->short_packet_received) {
-+ raise_exception(fsg, FSG_STATE_ABORT_BULK_OUT);
-+ rc = -EINTR;
-+ }
-+
-+ /* We haven't processed all the incoming data. Even though
-+ * we may be allowed to stall, doing so would cause a race.
-+ * The controller may already have ACK'ed all the remaining
-+ * bulk-out packets, in which case the host wouldn't see a
-+ * STALL. Not realizing the endpoint was halted, it wouldn't
-+ * clear the halt -- leading to problems later on. */
-+#if 0
-+ else if (mod_data.can_stall) {
-+ fsg_set_halt(fsg, fsg->bulk_out);
-+ raise_exception(fsg, FSG_STATE_ABORT_BULK_OUT);
-+ rc = -EINTR;
-+ }
-+#endif
-+
-+ /* We can't stall. Read in the excess data and throw it
-+ * all away. */
-+ else
-+ rc = throw_away_data(fsg);
-+ break;
-+ }
-+ return rc;
-+}
-+
-+
-+static int send_status(struct fsg_dev *fsg)
-+{
-+ struct fsg_lun *curlun = fsg->curlun;
-+ struct fsg_buffhd *bh;
-+ int rc;
-+ u8 status = US_BULK_STAT_OK;
-+ u32 sd, sdinfo = 0;
-+
-+ /* Wait for the next buffer to become available */
-+ bh = fsg->next_buffhd_to_fill;
-+ while (bh->state != BUF_STATE_EMPTY) {
-+ rc = sleep_thread(fsg);
-+ if (rc)
-+ return rc;
-+ }
-+
-+ if (curlun) {
-+ sd = curlun->sense_data;
-+ sdinfo = curlun->sense_data_info;
-+ } else if (fsg->bad_lun_okay)
-+ sd = SS_NO_SENSE;
-+ else
-+ sd = SS_LOGICAL_UNIT_NOT_SUPPORTED;
-+
-+ if (fsg->phase_error) {
-+ DBG(fsg, "sending phase-error status\n");
-+ status = US_BULK_STAT_PHASE;
-+ sd = SS_INVALID_COMMAND;
-+ } else if (sd != SS_NO_SENSE) {
-+ DBG(fsg, "sending command-failure status\n");
-+ status = US_BULK_STAT_FAIL;
-+ VDBG(fsg, " sense data: SK x%02x, ASC x%02x, ASCQ x%02x;"
-+ " info x%x\n",
-+ SK(sd), ASC(sd), ASCQ(sd), sdinfo);
-+ }
-+
-+ if (transport_is_bbb()) {
-+ struct bulk_cs_wrap *csw = bh->buf;
-+
-+ /* Store and send the Bulk-only CSW */
-+ csw->Signature = cpu_to_le32(US_BULK_CS_SIGN);
-+ csw->Tag = fsg->tag;
-+ csw->Residue = cpu_to_le32(fsg->residue);
-+ csw->Status = status;
-+
-+ bh->inreq->length = US_BULK_CS_WRAP_LEN;
-+ bh->inreq->zero = 0;
-+ start_transfer(fsg, fsg->bulk_in, bh->inreq,
-+ &bh->inreq_busy, &bh->state);
-+
-+ } else if (mod_data.transport_type == USB_PR_CB) {
-+
-+ /* Control-Bulk transport has no status phase! */
-+ return 0;
-+
-+ } else { // USB_PR_CBI
-+ struct interrupt_data *buf = bh->buf;
-+
-+ /* Store and send the Interrupt data. UFI sends the ASC
-+ * and ASCQ bytes. Everything else sends a Type (which
-+ * is always 0) and the status Value. */
-+ if (mod_data.protocol_type == USB_SC_UFI) {
-+ buf->bType = ASC(sd);
-+ buf->bValue = ASCQ(sd);
-+ } else {
-+ buf->bType = 0;
-+ buf->bValue = status;
-+ }
-+ fsg->intreq->length = CBI_INTERRUPT_DATA_LEN;
-+
-+ fsg->intr_buffhd = bh; // Point to the right buffhd
-+ fsg->intreq->buf = bh->inreq->buf;
-+ fsg->intreq->context = bh;
-+ start_transfer(fsg, fsg->intr_in, fsg->intreq,
-+ &fsg->intreq_busy, &bh->state);
-+ }
-+
-+ fsg->next_buffhd_to_fill = bh->next;
-+ return 0;
-+}
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+/* Check whether the command is properly formed and whether its data size
-+ * and direction agree with the values we already have. */
-+static int check_command(struct fsg_dev *fsg, int cmnd_size,
-+ enum data_direction data_dir, unsigned int mask,
-+ int needs_medium, const char *name)
-+{
-+ int i;
-+ int lun = fsg->cmnd[1] >> 5;
-+ static const char dirletter[4] = {'u', 'o', 'i', 'n'};
-+ char hdlen[20];
-+ struct fsg_lun *curlun;
-+
-+ /* Adjust the expected cmnd_size for protocol encapsulation padding.
-+ * Transparent SCSI doesn't pad. */
-+ if (protocol_is_scsi())
-+ ;
-+
-+ /* There's some disagreement as to whether RBC pads commands or not.
-+ * We'll play it safe and accept either form. */
-+ else if (mod_data.protocol_type == USB_SC_RBC) {
-+ if (fsg->cmnd_size == 12)
-+ cmnd_size = 12;
-+
-+ /* All the other protocols pad to 12 bytes */
-+ } else
-+ cmnd_size = 12;
-+
-+ hdlen[0] = 0;
-+ if (fsg->data_dir != DATA_DIR_UNKNOWN)
-+ sprintf(hdlen, ", H%c=%u", dirletter[(int) fsg->data_dir],
-+ fsg->data_size);
-+ VDBG(fsg, "SCSI command: %s; Dc=%d, D%c=%u; Hc=%d%s\n",
-+ name, cmnd_size, dirletter[(int) data_dir],
-+ fsg->data_size_from_cmnd, fsg->cmnd_size, hdlen);
-+
-+ /* We can't reply at all until we know the correct data direction
-+ * and size. */
-+ if (fsg->data_size_from_cmnd == 0)
-+ data_dir = DATA_DIR_NONE;
-+ if (fsg->data_dir == DATA_DIR_UNKNOWN) { // CB or CBI
-+ fsg->data_dir = data_dir;
-+ fsg->data_size = fsg->data_size_from_cmnd;
-+
-+ } else { // Bulk-only
-+ if (fsg->data_size < fsg->data_size_from_cmnd) {
-+
-+ /* Host data size < Device data size is a phase error.
-+ * Carry out the command, but only transfer as much
-+ * as we are allowed. */
-+ fsg->data_size_from_cmnd = fsg->data_size;
-+ fsg->phase_error = 1;
-+ }
-+ }
-+ fsg->residue = fsg->usb_amount_left = fsg->data_size;
-+
-+ /* Conflicting data directions is a phase error */
-+ if (fsg->data_dir != data_dir && fsg->data_size_from_cmnd > 0) {
-+ fsg->phase_error = 1;
-+ return -EINVAL;
-+ }
-+
-+ /* Verify the length of the command itself */
-+ if (cmnd_size != fsg->cmnd_size) {
-+
-+ /* Special case workaround: There are plenty of buggy SCSI
-+ * implementations. Many have issues with cbw->Length
-+ * field passing a wrong command size. For those cases we
-+ * always try to work around the problem by using the length
-+ * sent by the host side provided it is at least as large
-+ * as the correct command length.
-+ * Examples of such cases would be MS-Windows, which issues
-+ * REQUEST SENSE with cbw->Length == 12 where it should
-+ * be 6, and xbox360 issuing INQUIRY, TEST UNIT READY and
-+ * REQUEST SENSE with cbw->Length == 10 where it should
-+ * be 6 as well.
-+ */
-+ if (cmnd_size <= fsg->cmnd_size) {
-+ DBG(fsg, "%s is buggy! Expected length %d "
-+ "but we got %d\n", name,
-+ cmnd_size, fsg->cmnd_size);
-+ cmnd_size = fsg->cmnd_size;
-+ } else {
-+ fsg->phase_error = 1;
-+ return -EINVAL;
-+ }
-+ }
-+
-+ /* Check that the LUN values are consistent */
-+ if (transport_is_bbb()) {
-+ if (fsg->lun != lun)
-+ DBG(fsg, "using LUN %d from CBW, "
-+ "not LUN %d from CDB\n",
-+ fsg->lun, lun);
-+ }
-+
-+ /* Check the LUN */
-+ curlun = fsg->curlun;
-+ if (curlun) {
-+ if (fsg->cmnd[0] != REQUEST_SENSE) {
-+ curlun->sense_data = SS_NO_SENSE;
-+ curlun->sense_data_info = 0;
-+ curlun->info_valid = 0;
-+ }
-+ } else {
-+ fsg->bad_lun_okay = 0;
-+
-+ /* INQUIRY and REQUEST SENSE commands are explicitly allowed
-+ * to use unsupported LUNs; all others may not. */
-+ if (fsg->cmnd[0] != INQUIRY &&
-+ fsg->cmnd[0] != REQUEST_SENSE) {
-+ DBG(fsg, "unsupported LUN %d\n", fsg->lun);
-+ return -EINVAL;
-+ }
-+ }
-+
-+ /* If a unit attention condition exists, only INQUIRY and
-+ * REQUEST SENSE commands are allowed; anything else must fail. */
-+ if (curlun && curlun->unit_attention_data != SS_NO_SENSE &&
-+ fsg->cmnd[0] != INQUIRY &&
-+ fsg->cmnd[0] != REQUEST_SENSE) {
-+ curlun->sense_data = curlun->unit_attention_data;
-+ curlun->unit_attention_data = SS_NO_SENSE;
-+ return -EINVAL;
-+ }
-+
-+ /* Check that only command bytes listed in the mask are non-zero */
-+ fsg->cmnd[1] &= 0x1f; // Mask away the LUN
-+ for (i = 1; i < cmnd_size; ++i) {
-+ if (fsg->cmnd[i] && !(mask & (1 << i))) {
-+ if (curlun)
-+ curlun->sense_data = SS_INVALID_FIELD_IN_CDB;
-+ return -EINVAL;
-+ }
-+ }
-+
-+ /* If the medium isn't mounted and the command needs to access
-+ * it, return an error. */
-+ if (curlun && !fsg_lun_is_open(curlun) && needs_medium) {
-+ curlun->sense_data = SS_MEDIUM_NOT_PRESENT;
-+ return -EINVAL;
-+ }
-+
-+ return 0;
-+}
-+
-+/* wrapper of check_command for data size in blocks handling */
-+static int check_command_size_in_blocks(struct fsg_dev *fsg, int cmnd_size,
-+ enum data_direction data_dir, unsigned int mask,
-+ int needs_medium, const char *name)
-+{
-+ if (fsg->curlun)
-+ fsg->data_size_from_cmnd <<= fsg->curlun->blkbits;
-+ return check_command(fsg, cmnd_size, data_dir,
-+ mask, needs_medium, name);
-+}
-+
-+static int do_scsi_command(struct fsg_dev *fsg)
-+{
-+ struct fsg_buffhd *bh;
-+ int rc;
-+ int reply = -EINVAL;
-+ int i;
-+ static char unknown[16];
-+
-+ dump_cdb(fsg);
-+
-+ /* Wait for the next buffer to become available for data or status */
-+ bh = fsg->next_buffhd_to_drain = fsg->next_buffhd_to_fill;
-+ while (bh->state != BUF_STATE_EMPTY) {
-+ rc = sleep_thread(fsg);
-+ if (rc)
-+ return rc;
-+ }
-+ fsg->phase_error = 0;
-+ fsg->short_packet_received = 0;
-+
-+ down_read(&fsg->filesem); // We're using the backing file
-+ switch (fsg->cmnd[0]) {
-+
-+ case INQUIRY:
-+ fsg->data_size_from_cmnd = fsg->cmnd[4];
-+ if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST,
-+ (1<<4), 0,
-+ "INQUIRY")) == 0)
-+ reply = do_inquiry(fsg, bh);
-+ break;
-+
-+ case MODE_SELECT:
-+ fsg->data_size_from_cmnd = fsg->cmnd[4];
-+ if ((reply = check_command(fsg, 6, DATA_DIR_FROM_HOST,
-+ (1<<1) | (1<<4), 0,
-+ "MODE SELECT(6)")) == 0)
-+ reply = do_mode_select(fsg, bh);
-+ break;
-+
-+ case MODE_SELECT_10:
-+ fsg->data_size_from_cmnd = get_unaligned_be16(&fsg->cmnd[7]);
-+ if ((reply = check_command(fsg, 10, DATA_DIR_FROM_HOST,
-+ (1<<1) | (3<<7), 0,
-+ "MODE SELECT(10)")) == 0)
-+ reply = do_mode_select(fsg, bh);
-+ break;
-+
-+ case MODE_SENSE:
-+ fsg->data_size_from_cmnd = fsg->cmnd[4];
-+ if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST,
-+ (1<<1) | (1<<2) | (1<<4), 0,
-+ "MODE SENSE(6)")) == 0)
-+ reply = do_mode_sense(fsg, bh);
-+ break;
-+
-+ case MODE_SENSE_10:
-+ fsg->data_size_from_cmnd = get_unaligned_be16(&fsg->cmnd[7]);
-+ if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST,
-+ (1<<1) | (1<<2) | (3<<7), 0,
-+ "MODE SENSE(10)")) == 0)
-+ reply = do_mode_sense(fsg, bh);
-+ break;
-+
-+ case ALLOW_MEDIUM_REMOVAL:
-+ fsg->data_size_from_cmnd = 0;
-+ if ((reply = check_command(fsg, 6, DATA_DIR_NONE,
-+ (1<<4), 0,
-+ "PREVENT-ALLOW MEDIUM REMOVAL")) == 0)
-+ reply = do_prevent_allow(fsg);
-+ break;
-+
-+ case READ_6:
-+ i = fsg->cmnd[4];
-+ fsg->data_size_from_cmnd = (i == 0) ? 256 : i;
-+ if ((reply = check_command_size_in_blocks(fsg, 6,
-+ DATA_DIR_TO_HOST,
-+ (7<<1) | (1<<4), 1,
-+ "READ(6)")) == 0)
-+ reply = do_read(fsg);
-+ break;
-+
-+ case READ_10:
-+ fsg->data_size_from_cmnd = get_unaligned_be16(&fsg->cmnd[7]);
-+ if ((reply = check_command_size_in_blocks(fsg, 10,
-+ DATA_DIR_TO_HOST,
-+ (1<<1) | (0xf<<2) | (3<<7), 1,
-+ "READ(10)")) == 0)
-+ reply = do_read(fsg);
-+ break;
-+
-+ case READ_12:
-+ fsg->data_size_from_cmnd = get_unaligned_be32(&fsg->cmnd[6]);
-+ if ((reply = check_command_size_in_blocks(fsg, 12,
-+ DATA_DIR_TO_HOST,
-+ (1<<1) | (0xf<<2) | (0xf<<6), 1,
-+ "READ(12)")) == 0)
-+ reply = do_read(fsg);
-+ break;
-+
-+ case READ_CAPACITY:
-+ fsg->data_size_from_cmnd = 8;
-+ if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST,
-+ (0xf<<2) | (1<<8), 1,
-+ "READ CAPACITY")) == 0)
-+ reply = do_read_capacity(fsg, bh);
-+ break;
-+
-+ case READ_HEADER:
-+ if (!mod_data.cdrom)
-+ goto unknown_cmnd;
-+ fsg->data_size_from_cmnd = get_unaligned_be16(&fsg->cmnd[7]);
-+ if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST,
-+ (3<<7) | (0x1f<<1), 1,
-+ "READ HEADER")) == 0)
-+ reply = do_read_header(fsg, bh);
-+ break;
-+
-+ case READ_TOC:
-+ if (!mod_data.cdrom)
-+ goto unknown_cmnd;
-+ fsg->data_size_from_cmnd = get_unaligned_be16(&fsg->cmnd[7]);
-+ if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST,
-+ (7<<6) | (1<<1), 1,
-+ "READ TOC")) == 0)
-+ reply = do_read_toc(fsg, bh);
-+ break;
-+
-+ case READ_FORMAT_CAPACITIES:
-+ fsg->data_size_from_cmnd = get_unaligned_be16(&fsg->cmnd[7]);
-+ if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST,
-+ (3<<7), 1,
-+ "READ FORMAT CAPACITIES")) == 0)
-+ reply = do_read_format_capacities(fsg, bh);
-+ break;
-+
-+ case REQUEST_SENSE:
-+ fsg->data_size_from_cmnd = fsg->cmnd[4];
-+ if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST,
-+ (1<<4), 0,
-+ "REQUEST SENSE")) == 0)
-+ reply = do_request_sense(fsg, bh);
-+ break;
-+
-+ case START_STOP:
-+ fsg->data_size_from_cmnd = 0;
-+ if ((reply = check_command(fsg, 6, DATA_DIR_NONE,
-+ (1<<1) | (1<<4), 0,
-+ "START-STOP UNIT")) == 0)
-+ reply = do_start_stop(fsg);
-+ break;
-+
-+ case SYNCHRONIZE_CACHE:
-+ fsg->data_size_from_cmnd = 0;
-+ if ((reply = check_command(fsg, 10, DATA_DIR_NONE,
-+ (0xf<<2) | (3<<7), 1,
-+ "SYNCHRONIZE CACHE")) == 0)
-+ reply = do_synchronize_cache(fsg);
-+ break;
-+
-+ case TEST_UNIT_READY:
-+ fsg->data_size_from_cmnd = 0;
-+ reply = check_command(fsg, 6, DATA_DIR_NONE,
-+ 0, 1,
-+ "TEST UNIT READY");
-+ break;
-+
-+ /* Although optional, this command is used by MS-Windows. We
-+ * support a minimal version: BytChk must be 0. */
-+ case VERIFY:
-+ fsg->data_size_from_cmnd = 0;
-+ if ((reply = check_command(fsg, 10, DATA_DIR_NONE,
-+ (1<<1) | (0xf<<2) | (3<<7), 1,
-+ "VERIFY")) == 0)
-+ reply = do_verify(fsg);
-+ break;
-+
-+ case WRITE_6:
-+ i = fsg->cmnd[4];
-+ fsg->data_size_from_cmnd = (i == 0) ? 256 : i;
-+ if ((reply = check_command_size_in_blocks(fsg, 6,
-+ DATA_DIR_FROM_HOST,
-+ (7<<1) | (1<<4), 1,
-+ "WRITE(6)")) == 0)
-+ reply = do_write(fsg);
-+ break;
-+
-+ case WRITE_10:
-+ fsg->data_size_from_cmnd = get_unaligned_be16(&fsg->cmnd[7]);
-+ if ((reply = check_command_size_in_blocks(fsg, 10,
-+ DATA_DIR_FROM_HOST,
-+ (1<<1) | (0xf<<2) | (3<<7), 1,
-+ "WRITE(10)")) == 0)
-+ reply = do_write(fsg);
-+ break;
-+
-+ case WRITE_12:
-+ fsg->data_size_from_cmnd = get_unaligned_be32(&fsg->cmnd[6]);
-+ if ((reply = check_command_size_in_blocks(fsg, 12,
-+ DATA_DIR_FROM_HOST,
-+ (1<<1) | (0xf<<2) | (0xf<<6), 1,
-+ "WRITE(12)")) == 0)
-+ reply = do_write(fsg);
-+ break;
-+
-+ /* Some mandatory commands that we recognize but don't implement.
-+ * They don't mean much in this setting. It's left as an exercise
-+ * for anyone interested to implement RESERVE and RELEASE in terms
-+ * of Posix locks. */
-+ case FORMAT_UNIT:
-+ case RELEASE:
-+ case RESERVE:
-+ case SEND_DIAGNOSTIC:
-+ // Fall through
-+
-+ default:
-+ unknown_cmnd:
-+ fsg->data_size_from_cmnd = 0;
-+ sprintf(unknown, "Unknown x%02x", fsg->cmnd[0]);
-+ if ((reply = check_command(fsg, fsg->cmnd_size,
-+ DATA_DIR_UNKNOWN, ~0, 0, unknown)) == 0) {
-+ fsg->curlun->sense_data = SS_INVALID_COMMAND;
-+ reply = -EINVAL;
-+ }
-+ break;
-+ }
-+ up_read(&fsg->filesem);
-+
-+ if (reply == -EINTR || signal_pending(current))
-+ return -EINTR;
-+
-+ /* Set up the single reply buffer for finish_reply() */
-+ if (reply == -EINVAL)
-+ reply = 0; // Error reply length
-+ if (reply >= 0 && fsg->data_dir == DATA_DIR_TO_HOST) {
-+ reply = min((u32) reply, fsg->data_size_from_cmnd);
-+ bh->inreq->length = reply;
-+ bh->state = BUF_STATE_FULL;
-+ fsg->residue -= reply;
-+ } // Otherwise it's already set
-+
-+ return 0;
-+}
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+static int received_cbw(struct fsg_dev *fsg, struct fsg_buffhd *bh)
-+{
-+ struct usb_request *req = bh->outreq;
-+ struct bulk_cb_wrap *cbw = req->buf;
-+
-+ /* Was this a real packet? Should it be ignored? */
-+ if (req->status || test_bit(IGNORE_BULK_OUT, &fsg->atomic_bitflags))
-+ return -EINVAL;
-+
-+ /* Is the CBW valid? */
-+ if (req->actual != US_BULK_CB_WRAP_LEN ||
-+ cbw->Signature != cpu_to_le32(
-+ US_BULK_CB_SIGN)) {
-+ DBG(fsg, "invalid CBW: len %u sig 0x%x\n",
-+ req->actual,
-+ le32_to_cpu(cbw->Signature));
-+
-+ /* The Bulk-only spec says we MUST stall the IN endpoint
-+ * (6.6.1), so it's unavoidable. It also says we must
-+ * retain this state until the next reset, but there's
-+ * no way to tell the controller driver it should ignore
-+ * Clear-Feature(HALT) requests.
-+ *
-+ * We aren't required to halt the OUT endpoint; instead
-+ * we can simply accept and discard any data received
-+ * until the next reset. */
-+ wedge_bulk_in_endpoint(fsg);
-+ set_bit(IGNORE_BULK_OUT, &fsg->atomic_bitflags);
-+ return -EINVAL;
-+ }
-+
-+ /* Is the CBW meaningful? */
-+ if (cbw->Lun >= FSG_MAX_LUNS || cbw->Flags & ~US_BULK_FLAG_IN ||
-+ cbw->Length <= 0 || cbw->Length > MAX_COMMAND_SIZE) {
-+ DBG(fsg, "non-meaningful CBW: lun = %u, flags = 0x%x, "
-+ "cmdlen %u\n",
-+ cbw->Lun, cbw->Flags, cbw->Length);
-+
-+ /* We can do anything we want here, so let's stall the
-+ * bulk pipes if we are allowed to. */
-+ if (mod_data.can_stall) {
-+ fsg_set_halt(fsg, fsg->bulk_out);
-+ halt_bulk_in_endpoint(fsg);
-+ }
-+ return -EINVAL;
-+ }
-+
-+ /* Save the command for later */
-+ fsg->cmnd_size = cbw->Length;
-+ memcpy(fsg->cmnd, cbw->CDB, fsg->cmnd_size);
-+ if (cbw->Flags & US_BULK_FLAG_IN)
-+ fsg->data_dir = DATA_DIR_TO_HOST;
-+ else
-+ fsg->data_dir = DATA_DIR_FROM_HOST;
-+ fsg->data_size = le32_to_cpu(cbw->DataTransferLength);
-+ if (fsg->data_size == 0)
-+ fsg->data_dir = DATA_DIR_NONE;
-+ fsg->lun = cbw->Lun;
-+ fsg->tag = cbw->Tag;
-+ return 0;
-+}
-+
-+
-+static int get_next_command(struct fsg_dev *fsg)
-+{
-+ struct fsg_buffhd *bh;
-+ int rc = 0;
-+
-+ if (transport_is_bbb()) {
-+
-+ /* Wait for the next buffer to become available */
-+ bh = fsg->next_buffhd_to_fill;
-+ while (bh->state != BUF_STATE_EMPTY) {
-+ rc = sleep_thread(fsg);
-+ if (rc)
-+ return rc;
-+ }
-+
-+ /* Queue a request to read a Bulk-only CBW */
-+ set_bulk_out_req_length(fsg, bh, US_BULK_CB_WRAP_LEN);
-+ start_transfer(fsg, fsg->bulk_out, bh->outreq,
-+ &bh->outreq_busy, &bh->state);
-+
-+ /* We will drain the buffer in software, which means we
-+ * can reuse it for the next filling. No need to advance
-+ * next_buffhd_to_fill. */
-+
-+ /* Wait for the CBW to arrive */
-+ while (bh->state != BUF_STATE_FULL) {
-+ rc = sleep_thread(fsg);
-+ if (rc)
-+ return rc;
-+ }
-+ smp_rmb();
-+ rc = received_cbw(fsg, bh);
-+ bh->state = BUF_STATE_EMPTY;
-+
-+ } else { // USB_PR_CB or USB_PR_CBI
-+
-+ /* Wait for the next command to arrive */
-+ while (fsg->cbbuf_cmnd_size == 0) {
-+ rc = sleep_thread(fsg);
-+ if (rc)
-+ return rc;
-+ }
-+
-+ /* Is the previous status interrupt request still busy?
-+ * The host is allowed to skip reading the status,
-+ * so we must cancel it. */
-+ if (fsg->intreq_busy)
-+ usb_ep_dequeue(fsg->intr_in, fsg->intreq);
-+
-+ /* Copy the command and mark the buffer empty */
-+ fsg->data_dir = DATA_DIR_UNKNOWN;
-+ spin_lock_irq(&fsg->lock);
-+ fsg->cmnd_size = fsg->cbbuf_cmnd_size;
-+ memcpy(fsg->cmnd, fsg->cbbuf_cmnd, fsg->cmnd_size);
-+ fsg->cbbuf_cmnd_size = 0;
-+ spin_unlock_irq(&fsg->lock);
-+
-+ /* Use LUN from the command */
-+ fsg->lun = fsg->cmnd[1] >> 5;
-+ }
-+
-+ /* Update current lun */
-+ if (fsg->lun >= 0 && fsg->lun < fsg->nluns)
-+ fsg->curlun = &fsg->luns[fsg->lun];
-+ else
-+ fsg->curlun = NULL;
-+
-+ return rc;
-+}
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+static int enable_endpoint(struct fsg_dev *fsg, struct usb_ep *ep,
-+ const struct usb_endpoint_descriptor *d)
-+{
-+ int rc;
-+
-+ ep->driver_data = fsg;
-+ ep->desc = d;
-+ rc = usb_ep_enable(ep);
-+ if (rc)
-+ ERROR(fsg, "can't enable %s, result %d\n", ep->name, rc);
-+ return rc;
-+}
-+
-+static int alloc_request(struct fsg_dev *fsg, struct usb_ep *ep,
-+ struct usb_request **preq)
-+{
-+ *preq = usb_ep_alloc_request(ep, GFP_ATOMIC);
-+ if (*preq)
-+ return 0;
-+ ERROR(fsg, "can't allocate request for %s\n", ep->name);
-+ return -ENOMEM;
-+}
-+
-+/*
-+ * Reset interface setting and re-init endpoint state (toggle etc).
-+ * Call with altsetting < 0 to disable the interface. The only other
-+ * available altsetting is 0, which enables the interface.
-+ */
-+static int do_set_interface(struct fsg_dev *fsg, int altsetting)
-+{
-+ int rc = 0;
-+ int i;
-+ const struct usb_endpoint_descriptor *d;
-+
-+ if (fsg->running)
-+ DBG(fsg, "reset interface\n");
-+
-+reset:
-+ /* Deallocate the requests */
-+ for (i = 0; i < fsg_num_buffers; ++i) {
-+ struct fsg_buffhd *bh = &fsg->buffhds[i];
-+
-+ if (bh->inreq) {
-+ usb_ep_free_request(fsg->bulk_in, bh->inreq);
-+ bh->inreq = NULL;
-+ }
-+ if (bh->outreq) {
-+ usb_ep_free_request(fsg->bulk_out, bh->outreq);
-+ bh->outreq = NULL;
-+ }
-+ }
-+ if (fsg->intreq) {
-+ usb_ep_free_request(fsg->intr_in, fsg->intreq);
-+ fsg->intreq = NULL;
-+ }
-+
-+ /* Disable the endpoints */
-+ if (fsg->bulk_in_enabled) {
-+ usb_ep_disable(fsg->bulk_in);
-+ fsg->bulk_in_enabled = 0;
-+ }
-+ if (fsg->bulk_out_enabled) {
-+ usb_ep_disable(fsg->bulk_out);
-+ fsg->bulk_out_enabled = 0;
-+ }
-+ if (fsg->intr_in_enabled) {
-+ usb_ep_disable(fsg->intr_in);
-+ fsg->intr_in_enabled = 0;
-+ }
-+
-+ fsg->running = 0;
-+ if (altsetting < 0 || rc != 0)
-+ return rc;
-+
-+ DBG(fsg, "set interface %d\n", altsetting);
-+
-+ /* Enable the endpoints */
-+ d = fsg_ep_desc(fsg->gadget,
-+ &fsg_fs_bulk_in_desc, &fsg_hs_bulk_in_desc,
-+ &fsg_ss_bulk_in_desc);
-+ if ((rc = enable_endpoint(fsg, fsg->bulk_in, d)) != 0)
-+ goto reset;
-+ fsg->bulk_in_enabled = 1;
-+
-+ d = fsg_ep_desc(fsg->gadget,
-+ &fsg_fs_bulk_out_desc, &fsg_hs_bulk_out_desc,
-+ &fsg_ss_bulk_out_desc);
-+ if ((rc = enable_endpoint(fsg, fsg->bulk_out, d)) != 0)
-+ goto reset;
-+ fsg->bulk_out_enabled = 1;
-+ fsg->bulk_out_maxpacket = usb_endpoint_maxp(d);
-+ clear_bit(IGNORE_BULK_OUT, &fsg->atomic_bitflags);
-+
-+ if (transport_is_cbi()) {
-+ d = fsg_ep_desc(fsg->gadget,
-+ &fsg_fs_intr_in_desc, &fsg_hs_intr_in_desc,
-+ &fsg_ss_intr_in_desc);
-+ if ((rc = enable_endpoint(fsg, fsg->intr_in, d)) != 0)
-+ goto reset;
-+ fsg->intr_in_enabled = 1;
-+ }
-+
-+ /* Allocate the requests */
-+ for (i = 0; i < fsg_num_buffers; ++i) {
-+ struct fsg_buffhd *bh = &fsg->buffhds[i];
-+
-+ if ((rc = alloc_request(fsg, fsg->bulk_in, &bh->inreq)) != 0)
-+ goto reset;
-+ if ((rc = alloc_request(fsg, fsg->bulk_out, &bh->outreq)) != 0)
-+ goto reset;
-+ bh->inreq->buf = bh->outreq->buf = bh->buf;
-+ bh->inreq->context = bh->outreq->context = bh;
-+ bh->inreq->complete = bulk_in_complete;
-+ bh->outreq->complete = bulk_out_complete;
-+ }
-+ if (transport_is_cbi()) {
-+ if ((rc = alloc_request(fsg, fsg->intr_in, &fsg->intreq)) != 0)
-+ goto reset;
-+ fsg->intreq->complete = intr_in_complete;
-+ }
-+
-+ fsg->running = 1;
-+ for (i = 0; i < fsg->nluns; ++i)
-+ fsg->luns[i].unit_attention_data = SS_RESET_OCCURRED;
-+ return rc;
-+}
-+
-+
-+/*
-+ * Change our operational configuration. This code must agree with the code
-+ * that returns config descriptors, and with interface altsetting code.
-+ *
-+ * It's also responsible for power management interactions. Some
-+ * configurations might not work with our current power sources.
-+ * For now we just assume the gadget is always self-powered.
-+ */
-+static int do_set_config(struct fsg_dev *fsg, u8 new_config)
-+{
-+ int rc = 0;
-+
-+ /* Disable the single interface */
-+ if (fsg->config != 0) {
-+ DBG(fsg, "reset config\n");
-+ fsg->config = 0;
-+ rc = do_set_interface(fsg, -1);
-+ }
-+
-+ /* Enable the interface */
-+ if (new_config != 0) {
-+ fsg->config = new_config;
-+ if ((rc = do_set_interface(fsg, 0)) != 0)
-+ fsg->config = 0; // Reset on errors
-+ else
-+ INFO(fsg, "%s config #%d\n",
-+ usb_speed_string(fsg->gadget->speed),
-+ fsg->config);
-+ }
-+ return rc;
-+}
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+static void handle_exception(struct fsg_dev *fsg)
-+{
-+ siginfo_t info;
-+ int sig;
-+ int i;
-+ int num_active;
-+ struct fsg_buffhd *bh;
-+ enum fsg_state old_state;
-+ u8 new_config;
-+ struct fsg_lun *curlun;
-+ unsigned int exception_req_tag;
-+ int rc;
-+
-+ /* Clear the existing signals. Anything but SIGUSR1 is converted
-+ * into a high-priority EXIT exception. */
-+ for (;;) {
-+ sig = dequeue_signal_lock(current, ¤t->blocked, &info);
-+ if (!sig)
-+ break;
-+ if (sig != SIGUSR1) {
-+ if (fsg->state < FSG_STATE_EXIT)
-+ DBG(fsg, "Main thread exiting on signal\n");
-+ raise_exception(fsg, FSG_STATE_EXIT);
-+ }
-+ }
-+
-+ /* Cancel all the pending transfers */
-+ if (fsg->intreq_busy)
-+ usb_ep_dequeue(fsg->intr_in, fsg->intreq);
-+ for (i = 0; i < fsg_num_buffers; ++i) {
-+ bh = &fsg->buffhds[i];
-+ if (bh->inreq_busy)
-+ usb_ep_dequeue(fsg->bulk_in, bh->inreq);
-+ if (bh->outreq_busy)
-+ usb_ep_dequeue(fsg->bulk_out, bh->outreq);
-+ }
-+
-+ /* Wait until everything is idle */
-+ for (;;) {
-+ num_active = fsg->intreq_busy;
-+ for (i = 0; i < fsg_num_buffers; ++i) {
-+ bh = &fsg->buffhds[i];
-+ num_active += bh->inreq_busy + bh->outreq_busy;
-+ }
-+ if (num_active == 0)
-+ break;
-+ if (sleep_thread(fsg))
-+ return;
-+ }
-+
-+ /* Clear out the controller's fifos */
-+ if (fsg->bulk_in_enabled)
-+ usb_ep_fifo_flush(fsg->bulk_in);
-+ if (fsg->bulk_out_enabled)
-+ usb_ep_fifo_flush(fsg->bulk_out);
-+ if (fsg->intr_in_enabled)
-+ usb_ep_fifo_flush(fsg->intr_in);
-+
-+ /* Reset the I/O buffer states and pointers, the SCSI
-+ * state, and the exception. Then invoke the handler. */
-+ spin_lock_irq(&fsg->lock);
-+
-+ for (i = 0; i < fsg_num_buffers; ++i) {
-+ bh = &fsg->buffhds[i];
-+ bh->state = BUF_STATE_EMPTY;
-+ }
-+ fsg->next_buffhd_to_fill = fsg->next_buffhd_to_drain =
-+ &fsg->buffhds[0];
-+
-+ exception_req_tag = fsg->exception_req_tag;
-+ new_config = fsg->new_config;
-+ old_state = fsg->state;
-+
-+ if (old_state == FSG_STATE_ABORT_BULK_OUT)
-+ fsg->state = FSG_STATE_STATUS_PHASE;
-+ else {
-+ for (i = 0; i < fsg->nluns; ++i) {
-+ curlun = &fsg->luns[i];
-+ curlun->prevent_medium_removal = 0;
-+ curlun->sense_data = curlun->unit_attention_data =
-+ SS_NO_SENSE;
-+ curlun->sense_data_info = 0;
-+ curlun->info_valid = 0;
-+ }
-+ fsg->state = FSG_STATE_IDLE;
-+ }
-+ spin_unlock_irq(&fsg->lock);
-+
-+ /* Carry out any extra actions required for the exception */
-+ switch (old_state) {
-+ default:
-+ break;
-+
-+ case FSG_STATE_ABORT_BULK_OUT:
-+ send_status(fsg);
-+ spin_lock_irq(&fsg->lock);
-+ if (fsg->state == FSG_STATE_STATUS_PHASE)
-+ fsg->state = FSG_STATE_IDLE;
-+ spin_unlock_irq(&fsg->lock);
-+ break;
-+
-+ case FSG_STATE_RESET:
-+ /* In case we were forced against our will to halt a
-+ * bulk endpoint, clear the halt now. (The SuperH UDC
-+ * requires this.) */
-+ if (test_and_clear_bit(IGNORE_BULK_OUT, &fsg->atomic_bitflags))
-+ usb_ep_clear_halt(fsg->bulk_in);
-+
-+ if (transport_is_bbb()) {
-+ if (fsg->ep0_req_tag == exception_req_tag)
-+ ep0_queue(fsg); // Complete the status stage
-+
-+ } else if (transport_is_cbi())
-+ send_status(fsg); // Status by interrupt pipe
-+
-+ /* Technically this should go here, but it would only be
-+ * a waste of time. Ditto for the INTERFACE_CHANGE and
-+ * CONFIG_CHANGE cases. */
-+ // for (i = 0; i < fsg->nluns; ++i)
-+ // fsg->luns[i].unit_attention_data = SS_RESET_OCCURRED;
-+ break;
-+
-+ case FSG_STATE_INTERFACE_CHANGE:
-+ rc = do_set_interface(fsg, 0);
-+ if (fsg->ep0_req_tag != exception_req_tag)
-+ break;
-+ if (rc != 0) // STALL on errors
-+ fsg_set_halt(fsg, fsg->ep0);
-+ else // Complete the status stage
-+ ep0_queue(fsg);
-+ break;
-+
-+ case FSG_STATE_CONFIG_CHANGE:
-+ rc = do_set_config(fsg, new_config);
-+ if (fsg->ep0_req_tag != exception_req_tag)
-+ break;
-+ if (rc != 0) // STALL on errors
-+ fsg_set_halt(fsg, fsg->ep0);
-+ else // Complete the status stage
-+ ep0_queue(fsg);
-+ break;
-+
-+ case FSG_STATE_DISCONNECT:
-+ for (i = 0; i < fsg->nluns; ++i)
-+ fsg_lun_fsync_sub(fsg->luns + i);
-+ do_set_config(fsg, 0); // Unconfigured state
-+ break;
-+
-+ case FSG_STATE_EXIT:
-+ case FSG_STATE_TERMINATED:
-+ do_set_config(fsg, 0); // Free resources
-+ spin_lock_irq(&fsg->lock);
-+ fsg->state = FSG_STATE_TERMINATED; // Stop the thread
-+ spin_unlock_irq(&fsg->lock);
-+ break;
-+ }
-+}
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+static int fsg_main_thread(void *fsg_)
-+{
-+ struct fsg_dev *fsg = fsg_;
-+
-+ /* Allow the thread to be killed by a signal, but set the signal mask
-+ * to block everything but INT, TERM, KILL, and USR1. */
-+ allow_signal(SIGINT);
-+ allow_signal(SIGTERM);
-+ allow_signal(SIGKILL);
-+ allow_signal(SIGUSR1);
-+
-+ /* Allow the thread to be frozen */
-+ set_freezable();
-+
-+ /* Arrange for userspace references to be interpreted as kernel
-+ * pointers. That way we can pass a kernel pointer to a routine
-+ * that expects a __user pointer and it will work okay. */
-+ set_fs(get_ds());
-+
-+ /* The main loop */
-+ while (fsg->state != FSG_STATE_TERMINATED) {
-+ if (exception_in_progress(fsg) || signal_pending(current)) {
-+ handle_exception(fsg);
-+ continue;
-+ }
-+
-+ if (!fsg->running) {
-+ sleep_thread(fsg);
-+ continue;
-+ }
-+
-+ if (get_next_command(fsg))
-+ continue;
-+
-+ spin_lock_irq(&fsg->lock);
-+ if (!exception_in_progress(fsg))
-+ fsg->state = FSG_STATE_DATA_PHASE;
-+ spin_unlock_irq(&fsg->lock);
-+
-+ if (do_scsi_command(fsg) || finish_reply(fsg))
-+ continue;
-+
-+ spin_lock_irq(&fsg->lock);
-+ if (!exception_in_progress(fsg))
-+ fsg->state = FSG_STATE_STATUS_PHASE;
-+ spin_unlock_irq(&fsg->lock);
-+
-+ if (send_status(fsg))
-+ continue;
-+
-+ spin_lock_irq(&fsg->lock);
-+ if (!exception_in_progress(fsg))
-+ fsg->state = FSG_STATE_IDLE;
-+ spin_unlock_irq(&fsg->lock);
-+ }
-+
-+ spin_lock_irq(&fsg->lock);
-+ fsg->thread_task = NULL;
-+ spin_unlock_irq(&fsg->lock);
-+
-+ /* If we are exiting because of a signal, unregister the
-+ * gadget driver. */
-+ if (test_and_clear_bit(REGISTERED, &fsg->atomic_bitflags))
-+ usb_gadget_unregister_driver(&fsg_driver);
-+
-+ /* Let the unbind and cleanup routines know the thread has exited */
-+ complete_and_exit(&fsg->thread_notifier, 0);
-+}
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+
-+/* The write permissions and store_xxx pointers are set in fsg_bind() */
-+static DEVICE_ATTR(ro, 0444, fsg_show_ro, NULL);
-+static DEVICE_ATTR(nofua, 0644, fsg_show_nofua, NULL);
-+static DEVICE_ATTR(file, 0444, fsg_show_file, NULL);
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+static void fsg_release(struct kref *ref)
-+{
-+ struct fsg_dev *fsg = container_of(ref, struct fsg_dev, ref);
-+
-+ kfree(fsg->luns);
-+ kfree(fsg);
-+}
-+
-+static void lun_release(struct device *dev)
-+{
-+ struct rw_semaphore *filesem = dev_get_drvdata(dev);
-+ struct fsg_dev *fsg =
-+ container_of(filesem, struct fsg_dev, filesem);
-+
-+ kref_put(&fsg->ref, fsg_release);
-+}
-+
-+static void /* __init_or_exit */ fsg_unbind(struct usb_gadget *gadget)
-+{
-+ struct fsg_dev *fsg = get_gadget_data(gadget);
-+ int i;
-+ struct fsg_lun *curlun;
-+ struct usb_request *req = fsg->ep0req;
-+
-+ DBG(fsg, "unbind\n");
-+ clear_bit(REGISTERED, &fsg->atomic_bitflags);
-+
-+ /* If the thread isn't already dead, tell it to exit now */
-+ if (fsg->state != FSG_STATE_TERMINATED) {
-+ raise_exception(fsg, FSG_STATE_EXIT);
-+ wait_for_completion(&fsg->thread_notifier);
-+
-+ /* The cleanup routine waits for this completion also */
-+ complete(&fsg->thread_notifier);
-+ }
-+
-+ /* Unregister the sysfs attribute files and the LUNs */
-+ for (i = 0; i < fsg->nluns; ++i) {
-+ curlun = &fsg->luns[i];
-+ if (curlun->registered) {
-+ device_remove_file(&curlun->dev, &dev_attr_nofua);
-+ device_remove_file(&curlun->dev, &dev_attr_ro);
-+ device_remove_file(&curlun->dev, &dev_attr_file);
-+ fsg_lun_close(curlun);
-+ device_unregister(&curlun->dev);
-+ curlun->registered = 0;
-+ }
-+ }
-+
-+ /* Free the data buffers */
-+ for (i = 0; i < fsg_num_buffers; ++i)
-+ kfree(fsg->buffhds[i].buf);
-+
-+ /* Free the request and buffer for endpoint 0 */
-+ if (req) {
-+ kfree(req->buf);
-+ usb_ep_free_request(fsg->ep0, req);
-+ }
-+
-+ set_gadget_data(gadget, NULL);
-+}
-+
-+
-+static int __init check_parameters(struct fsg_dev *fsg)
-+{
-+ int prot;
-+ int gcnum;
-+
-+ /* Store the default values */
-+ mod_data.transport_type = USB_PR_BULK;
-+ mod_data.transport_name = "Bulk-only";
-+ mod_data.protocol_type = USB_SC_SCSI;
-+ mod_data.protocol_name = "Transparent SCSI";
-+
-+ /* Some peripheral controllers are known not to be able to
-+ * halt bulk endpoints correctly. If one of them is present,
-+ * disable stalls.
-+ */
-+ if (gadget_is_at91(fsg->gadget))
-+ mod_data.can_stall = 0;
-+
-+ if (mod_data.release == 0xffff) { // Parameter wasn't set
-+ gcnum = usb_gadget_controller_number(fsg->gadget);
-+ if (gcnum >= 0)
-+ mod_data.release = 0x0300 + gcnum;
-+ else {
-+ WARNING(fsg, "controller '%s' not recognized\n",
-+ fsg->gadget->name);
-+ mod_data.release = 0x0399;
-+ }
-+ }
-+
-+ prot = simple_strtol(mod_data.protocol_parm, NULL, 0);
-+
-+#ifdef CONFIG_USB_FILE_STORAGE_TEST
-+ if (strnicmp(mod_data.transport_parm, "BBB", 10) == 0) {
-+ ; // Use default setting
-+ } else if (strnicmp(mod_data.transport_parm, "CB", 10) == 0) {
-+ mod_data.transport_type = USB_PR_CB;
-+ mod_data.transport_name = "Control-Bulk";
-+ } else if (strnicmp(mod_data.transport_parm, "CBI", 10) == 0) {
-+ mod_data.transport_type = USB_PR_CBI;
-+ mod_data.transport_name = "Control-Bulk-Interrupt";
-+ } else {
-+ ERROR(fsg, "invalid transport: %s\n", mod_data.transport_parm);
-+ return -EINVAL;
-+ }
-+
-+ if (strnicmp(mod_data.protocol_parm, "SCSI", 10) == 0 ||
-+ prot == USB_SC_SCSI) {
-+ ; // Use default setting
-+ } else if (strnicmp(mod_data.protocol_parm, "RBC", 10) == 0 ||
-+ prot == USB_SC_RBC) {
-+ mod_data.protocol_type = USB_SC_RBC;
-+ mod_data.protocol_name = "RBC";
-+ } else if (strnicmp(mod_data.protocol_parm, "8020", 4) == 0 ||
-+ strnicmp(mod_data.protocol_parm, "ATAPI", 10) == 0 ||
-+ prot == USB_SC_8020) {
-+ mod_data.protocol_type = USB_SC_8020;
-+ mod_data.protocol_name = "8020i (ATAPI)";
-+ } else if (strnicmp(mod_data.protocol_parm, "QIC", 3) == 0 ||
-+ prot == USB_SC_QIC) {
-+ mod_data.protocol_type = USB_SC_QIC;
-+ mod_data.protocol_name = "QIC-157";
-+ } else if (strnicmp(mod_data.protocol_parm, "UFI", 10) == 0 ||
-+ prot == USB_SC_UFI) {
-+ mod_data.protocol_type = USB_SC_UFI;
-+ mod_data.protocol_name = "UFI";
-+ } else if (strnicmp(mod_data.protocol_parm, "8070", 4) == 0 ||
-+ prot == USB_SC_8070) {
-+ mod_data.protocol_type = USB_SC_8070;
-+ mod_data.protocol_name = "8070i";
-+ } else {
-+ ERROR(fsg, "invalid protocol: %s\n", mod_data.protocol_parm);
-+ return -EINVAL;
-+ }
-+
-+ mod_data.buflen &= PAGE_CACHE_MASK;
-+ if (mod_data.buflen <= 0) {
-+ ERROR(fsg, "invalid buflen\n");
-+ return -ETOOSMALL;
-+ }
-+
-+#endif /* CONFIG_USB_FILE_STORAGE_TEST */
-+
-+ /* Serial string handling.
-+ * On a real device, the serial string would be loaded
-+ * from permanent storage. */
-+ if (mod_data.serial) {
-+ const char *ch;
-+ unsigned len = 0;
-+
-+ /* Sanity check :
-+ * The CB[I] specification limits the serial string to
-+ * 12 uppercase hexadecimal characters.
-+ * BBB need at least 12 uppercase hexadecimal characters,
-+ * with a maximum of 126. */
-+ for (ch = mod_data.serial; *ch; ++ch) {
-+ ++len;
-+ if ((*ch < '0' || *ch > '9') &&
-+ (*ch < 'A' || *ch > 'F')) { /* not uppercase hex */
-+ WARNING(fsg,
-+ "Invalid serial string character: %c\n",
-+ *ch);
-+ goto no_serial;
-+ }
-+ }
-+ if (len > 126 ||
-+ (mod_data.transport_type == USB_PR_BULK && len < 12) ||
-+ (mod_data.transport_type != USB_PR_BULK && len > 12)) {
-+ WARNING(fsg, "Invalid serial string length!\n");
-+ goto no_serial;
-+ }
-+ fsg_strings[FSG_STRING_SERIAL - 1].s = mod_data.serial;
-+ } else {
-+ WARNING(fsg, "No serial-number string provided!\n");
-+ no_serial:
-+ device_desc.iSerialNumber = 0;
-+ }
-+
-+ return 0;
-+}
-+
-+
-+static int __init fsg_bind(struct usb_gadget *gadget)
-+{
-+ struct fsg_dev *fsg = the_fsg;
-+ int rc;
-+ int i;
-+ struct fsg_lun *curlun;
-+ struct usb_ep *ep;
-+ struct usb_request *req;
-+ char *pathbuf, *p;
-+
-+ fsg->gadget = gadget;
-+ set_gadget_data(gadget, fsg);
-+ fsg->ep0 = gadget->ep0;
-+ fsg->ep0->driver_data = fsg;
-+
-+ if ((rc = check_parameters(fsg)) != 0)
-+ goto out;
-+
-+ if (mod_data.removable) { // Enable the store_xxx attributes
-+ dev_attr_file.attr.mode = 0644;
-+ dev_attr_file.store = fsg_store_file;
-+ if (!mod_data.cdrom) {
-+ dev_attr_ro.attr.mode = 0644;
-+ dev_attr_ro.store = fsg_store_ro;
-+ }
-+ }
-+
-+ /* Only for removable media? */
-+ dev_attr_nofua.attr.mode = 0644;
-+ dev_attr_nofua.store = fsg_store_nofua;
-+
-+ /* Find out how many LUNs there should be */
-+ i = mod_data.nluns;
-+ if (i == 0)
-+ i = max(mod_data.num_filenames, 1u);
-+ if (i > FSG_MAX_LUNS) {
-+ ERROR(fsg, "invalid number of LUNs: %d\n", i);
-+ rc = -EINVAL;
-+ goto out;
-+ }
-+
-+ /* Create the LUNs, open their backing files, and register the
-+ * LUN devices in sysfs. */
-+ fsg->luns = kzalloc(i * sizeof(struct fsg_lun), GFP_KERNEL);
-+ if (!fsg->luns) {
-+ rc = -ENOMEM;
-+ goto out;
-+ }
-+ fsg->nluns = i;
-+
-+ for (i = 0; i < fsg->nluns; ++i) {
-+ curlun = &fsg->luns[i];
-+ curlun->cdrom = !!mod_data.cdrom;
-+ curlun->ro = mod_data.cdrom || mod_data.ro[i];
-+ curlun->initially_ro = curlun->ro;
-+ curlun->removable = mod_data.removable;
-+ curlun->nofua = mod_data.nofua[i];
-+ curlun->dev.release = lun_release;
-+ curlun->dev.parent = &gadget->dev;
-+ curlun->dev.driver = &fsg_driver.driver;
-+ dev_set_drvdata(&curlun->dev, &fsg->filesem);
-+ dev_set_name(&curlun->dev,"%s-lun%d",
-+ dev_name(&gadget->dev), i);
-+
-+ kref_get(&fsg->ref);
-+ rc = device_register(&curlun->dev);
-+ if (rc) {
-+ INFO(fsg, "failed to register LUN%d: %d\n", i, rc);
-+ put_device(&curlun->dev);
-+ goto out;
-+ }
-+ curlun->registered = 1;
-+
-+ rc = device_create_file(&curlun->dev, &dev_attr_ro);
-+ if (rc)
-+ goto out;
-+ rc = device_create_file(&curlun->dev, &dev_attr_nofua);
-+ if (rc)
-+ goto out;
-+ rc = device_create_file(&curlun->dev, &dev_attr_file);
-+ if (rc)
-+ goto out;
-+
-+ if (mod_data.file[i] && *mod_data.file[i]) {
-+ rc = fsg_lun_open(curlun, mod_data.file[i]);
-+ if (rc)
-+ goto out;
-+ } else if (!mod_data.removable) {
-+ ERROR(fsg, "no file given for LUN%d\n", i);
-+ rc = -EINVAL;
-+ goto out;
-+ }
-+ }
-+
-+ /* Find all the endpoints we will use */
-+ usb_ep_autoconfig_reset(gadget);
-+ ep = usb_ep_autoconfig(gadget, &fsg_fs_bulk_in_desc);
-+ if (!ep)
-+ goto autoconf_fail;
-+ ep->driver_data = fsg; // claim the endpoint
-+ fsg->bulk_in = ep;
-+
-+ ep = usb_ep_autoconfig(gadget, &fsg_fs_bulk_out_desc);
-+ if (!ep)
-+ goto autoconf_fail;
-+ ep->driver_data = fsg; // claim the endpoint
-+ fsg->bulk_out = ep;
-+
-+ if (transport_is_cbi()) {
-+ ep = usb_ep_autoconfig(gadget, &fsg_fs_intr_in_desc);
-+ if (!ep)
-+ goto autoconf_fail;
-+ ep->driver_data = fsg; // claim the endpoint
-+ fsg->intr_in = ep;
-+ }
-+
-+ /* Fix up the descriptors */
-+ device_desc.idVendor = cpu_to_le16(mod_data.vendor);
-+ device_desc.idProduct = cpu_to_le16(mod_data.product);
-+ device_desc.bcdDevice = cpu_to_le16(mod_data.release);
-+
-+ i = (transport_is_cbi() ? 3 : 2); // Number of endpoints
-+ fsg_intf_desc.bNumEndpoints = i;
-+ fsg_intf_desc.bInterfaceSubClass = mod_data.protocol_type;
-+ fsg_intf_desc.bInterfaceProtocol = mod_data.transport_type;
-+ fsg_fs_function[i + FSG_FS_FUNCTION_PRE_EP_ENTRIES] = NULL;
-+
-+ if (gadget_is_dualspeed(gadget)) {
-+ fsg_hs_function[i + FSG_HS_FUNCTION_PRE_EP_ENTRIES] = NULL;
-+
-+ /* Assume endpoint addresses are the same for both speeds */
-+ fsg_hs_bulk_in_desc.bEndpointAddress =
-+ fsg_fs_bulk_in_desc.bEndpointAddress;
-+ fsg_hs_bulk_out_desc.bEndpointAddress =
-+ fsg_fs_bulk_out_desc.bEndpointAddress;
-+ fsg_hs_intr_in_desc.bEndpointAddress =
-+ fsg_fs_intr_in_desc.bEndpointAddress;
-+ }
-+
-+ if (gadget_is_superspeed(gadget)) {
-+ unsigned max_burst;
-+
-+ fsg_ss_function[i + FSG_SS_FUNCTION_PRE_EP_ENTRIES] = NULL;
-+
-+ /* Calculate bMaxBurst, we know packet size is 1024 */
-+ max_burst = min_t(unsigned, mod_data.buflen / 1024, 15);
-+
-+ /* Assume endpoint addresses are the same for both speeds */
-+ fsg_ss_bulk_in_desc.bEndpointAddress =
-+ fsg_fs_bulk_in_desc.bEndpointAddress;
-+ fsg_ss_bulk_in_comp_desc.bMaxBurst = max_burst;
-+
-+ fsg_ss_bulk_out_desc.bEndpointAddress =
-+ fsg_fs_bulk_out_desc.bEndpointAddress;
-+ fsg_ss_bulk_out_comp_desc.bMaxBurst = max_burst;
-+ }
-+
-+ if (gadget_is_otg(gadget))
-+ fsg_otg_desc.bmAttributes |= USB_OTG_HNP;
-+
-+ rc = -ENOMEM;
-+
-+ /* Allocate the request and buffer for endpoint 0 */
-+ fsg->ep0req = req = usb_ep_alloc_request(fsg->ep0, GFP_KERNEL);
-+ if (!req)
-+ goto out;
-+ req->buf = kmalloc(EP0_BUFSIZE, GFP_KERNEL);
-+ if (!req->buf)
-+ goto out;
-+ req->complete = ep0_complete;
-+
-+ /* Allocate the data buffers */
-+ for (i = 0; i < fsg_num_buffers; ++i) {
-+ struct fsg_buffhd *bh = &fsg->buffhds[i];
-+
-+ /* Allocate for the bulk-in endpoint. We assume that
-+ * the buffer will also work with the bulk-out (and
-+ * interrupt-in) endpoint. */
-+ bh->buf = kmalloc(mod_data.buflen, GFP_KERNEL);
-+ if (!bh->buf)
-+ goto out;
-+ bh->next = bh + 1;
-+ }
-+ fsg->buffhds[fsg_num_buffers - 1].next = &fsg->buffhds[0];
-+
-+ /* This should reflect the actual gadget power source */
-+ usb_gadget_set_selfpowered(gadget);
-+
-+ snprintf(fsg_string_manufacturer, sizeof fsg_string_manufacturer,
-+ "%s %s with %s",
-+ init_utsname()->sysname, init_utsname()->release,
-+ gadget->name);
-+
-+ fsg->thread_task = kthread_create(fsg_main_thread, fsg,
-+ "file-storage-gadget");
-+ if (IS_ERR(fsg->thread_task)) {
-+ rc = PTR_ERR(fsg->thread_task);
-+ goto out;
-+ }
-+
-+ INFO(fsg, DRIVER_DESC ", version: " DRIVER_VERSION "\n");
-+ INFO(fsg, "NOTE: This driver is deprecated. "
-+ "Consider using g_mass_storage instead.\n");
-+ INFO(fsg, "Number of LUNs=%d\n", fsg->nluns);
-+
-+ pathbuf = kmalloc(PATH_MAX, GFP_KERNEL);
-+ for (i = 0; i < fsg->nluns; ++i) {
-+ curlun = &fsg->luns[i];
-+ if (fsg_lun_is_open(curlun)) {
-+ p = NULL;
-+ if (pathbuf) {
-+ p = d_path(&curlun->filp->f_path,
-+ pathbuf, PATH_MAX);
-+ if (IS_ERR(p))
-+ p = NULL;
-+ }
-+ LINFO(curlun, "ro=%d, nofua=%d, file: %s\n",
-+ curlun->ro, curlun->nofua, (p ? p : "(error)"));
-+ }
-+ }
-+ kfree(pathbuf);
-+
-+ DBG(fsg, "transport=%s (x%02x)\n",
-+ mod_data.transport_name, mod_data.transport_type);
-+ DBG(fsg, "protocol=%s (x%02x)\n",
-+ mod_data.protocol_name, mod_data.protocol_type);
-+ DBG(fsg, "VendorID=x%04x, ProductID=x%04x, Release=x%04x\n",
-+ mod_data.vendor, mod_data.product, mod_data.release);
-+ DBG(fsg, "removable=%d, stall=%d, cdrom=%d, buflen=%u\n",
-+ mod_data.removable, mod_data.can_stall,
-+ mod_data.cdrom, mod_data.buflen);
-+ DBG(fsg, "I/O thread pid: %d\n", task_pid_nr(fsg->thread_task));
-+
-+ set_bit(REGISTERED, &fsg->atomic_bitflags);
-+
-+ /* Tell the thread to start working */
-+ wake_up_process(fsg->thread_task);
-+ return 0;
-+
-+autoconf_fail:
-+ ERROR(fsg, "unable to autoconfigure all endpoints\n");
-+ rc = -ENOTSUPP;
-+
-+out:
-+ fsg->state = FSG_STATE_TERMINATED; // The thread is dead
-+ fsg_unbind(gadget);
-+ complete(&fsg->thread_notifier);
-+ return rc;
-+}
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+static void fsg_suspend(struct usb_gadget *gadget)
-+{
-+ struct fsg_dev *fsg = get_gadget_data(gadget);
-+
-+ DBG(fsg, "suspend\n");
-+ set_bit(SUSPENDED, &fsg->atomic_bitflags);
-+}
-+
-+static void fsg_resume(struct usb_gadget *gadget)
-+{
-+ struct fsg_dev *fsg = get_gadget_data(gadget);
-+
-+ DBG(fsg, "resume\n");
-+ clear_bit(SUSPENDED, &fsg->atomic_bitflags);
-+}
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+static struct usb_gadget_driver fsg_driver = {
-+ .max_speed = USB_SPEED_SUPER,
-+ .function = (char *) fsg_string_product,
-+ .unbind = fsg_unbind,
-+ .disconnect = fsg_disconnect,
-+ .setup = fsg_setup,
-+ .suspend = fsg_suspend,
-+ .resume = fsg_resume,
-+
-+ .driver = {
-+ .name = DRIVER_NAME,
-+ .owner = THIS_MODULE,
-+ // .release = ...
-+ // .suspend = ...
-+ // .resume = ...
-+ },
-+};
-+
-+
-+static int __init fsg_alloc(void)
-+{
-+ struct fsg_dev *fsg;
-+
-+ fsg = kzalloc(sizeof *fsg +
-+ fsg_num_buffers * sizeof *(fsg->buffhds), GFP_KERNEL);
-+
-+ if (!fsg)
-+ return -ENOMEM;
-+ spin_lock_init(&fsg->lock);
-+ init_rwsem(&fsg->filesem);
-+ kref_init(&fsg->ref);
-+ init_completion(&fsg->thread_notifier);
-+
-+ the_fsg = fsg;
-+ return 0;
-+}
-+
-+
-+static int __init fsg_init(void)
-+{
-+ int rc;
-+ struct fsg_dev *fsg;
-+
-+ rc = fsg_num_buffers_validate();
-+ if (rc != 0)
-+ return rc;
-+
-+ if ((rc = fsg_alloc()) != 0)
-+ return rc;
-+ fsg = the_fsg;
-+ if ((rc = usb_gadget_probe_driver(&fsg_driver, fsg_bind)) != 0)
-+ kref_put(&fsg->ref, fsg_release);
-+ return rc;
-+}
-+module_init(fsg_init);
-+
-+
-+static void __exit fsg_cleanup(void)
-+{
-+ struct fsg_dev *fsg = the_fsg;
-+
-+ /* Unregister the driver iff the thread hasn't already done so */
-+ if (test_and_clear_bit(REGISTERED, &fsg->atomic_bitflags))
-+ usb_gadget_unregister_driver(&fsg_driver);
-+
-+ /* Wait for the thread to finish up */
-+ wait_for_completion(&fsg->thread_notifier);
-+
-+ kref_put(&fsg->ref, fsg_release);
-+}
-+module_exit(fsg_cleanup);
---- a/drivers/usb/host/Kconfig
-+++ b/drivers/usb/host/Kconfig
-@@ -735,6 +735,19 @@ config USB_HWA_HCD
- To compile this driver a module, choose M here: the module
- will be called "hwa-hc".
-
-+config USB_DWCOTG
-+ tristate "Synopsis DWC host support"
-+ depends on USB
-+ help
-+ The Synopsis DWC controller is a dual-role
-+ host/peripheral/OTG ("On The Go") USB controllers.
-+
-+ Enable this option to support this IP in host controller mode.
-+ If unsure, say N.
-+
-+ To compile this driver as a module, choose M here: the
-+ modules built will be called dwc_otg and dwc_common_port.
-+
- config USB_IMX21_HCD
- tristate "i.MX21 HCD support"
- depends on ARM && ARCH_MXC
---- a/drivers/usb/host/Makefile
-+++ b/drivers/usb/host/Makefile
-@@ -69,6 +69,8 @@ obj-$(CONFIG_USB_SL811_CS) += sl811_cs.o
- obj-$(CONFIG_USB_U132_HCD) += u132-hcd.o
- obj-$(CONFIG_USB_R8A66597_HCD) += r8a66597-hcd.o
- obj-$(CONFIG_USB_HWA_HCD) += hwa-hc.o
-+
-+obj-$(CONFIG_USB_DWCOTG) += dwc_otg/ dwc_common_port/
- obj-$(CONFIG_USB_IMX21_HCD) += imx21-hcd.o
- obj-$(CONFIG_USB_FSL_MPH_DR_OF) += fsl-mph-dr-of.o
- obj-$(CONFIG_USB_EHCI_FSL) += ehci-fsl.o
---- /dev/null
-+++ b/drivers/usb/host/dwc_common_port/Makefile
-@@ -0,0 +1,58 @@
-+#
-+# Makefile for DWC_common library
-+#
-+
-+ifneq ($(KERNELRELEASE),)
-+
-+ccflags-y += -DDWC_LINUX
-+#ccflags-y += -DDEBUG
-+#ccflags-y += -DDWC_DEBUG_REGS
-+#ccflags-y += -DDWC_DEBUG_MEMORY
-+
-+ccflags-y += -DDWC_LIBMODULE
-+ccflags-y += -DDWC_CCLIB
-+#ccflags-y += -DDWC_CRYPTOLIB
-+ccflags-y += -DDWC_NOTIFYLIB
-+ccflags-y += -DDWC_UTFLIB
-+
-+obj-$(CONFIG_USB_DWCOTG) += dwc_common_port_lib.o
-+dwc_common_port_lib-objs := dwc_cc.o dwc_modpow.o dwc_dh.o \
-+ dwc_crypto.o dwc_notifier.o \
-+ dwc_common_linux.o dwc_mem.o
-+
-+kernrelwd := $(subst ., ,$(KERNELRELEASE))
-+kernrel3 := $(word 1,$(kernrelwd)).$(word 2,$(kernrelwd)).$(word 3,$(kernrelwd))
-+
-+ifneq ($(kernrel3),2.6.20)
-+# grayg - I only know that we use ccflags-y in 2.6.31 actually
-+ccflags-y += $(CPPFLAGS)
-+endif
-+
-+else
-+
-+#ifeq ($(KDIR),)
-+#$(error Must give "KDIR=/path/to/kernel/source" on command line or in environment)
-+#endif
-+
-+ifeq ($(ARCH),)
-+$(error Must give "ARCH=<arch>" on command line or in environment. Also, if \
-+ cross-compiling, must give "CROSS_COMPILE=/path/to/compiler/plus/tool-prefix-")
-+endif
-+
-+ifeq ($(DOXYGEN),)
-+DOXYGEN := doxygen
-+endif
-+
-+default:
-+ $(MAKE) -C$(KDIR) M=$(PWD) ARCH=$(ARCH) CROSS_COMPILE=$(CROSS_COMPILE) modules
-+
-+docs: $(wildcard *.[hc]) doc/doxygen.cfg
-+ $(DOXYGEN) doc/doxygen.cfg
-+
-+tags: $(wildcard *.[hc])
-+ $(CTAGS) -e $(wildcard *.[hc]) $(wildcard linux/*.[hc]) $(wildcard $(KDIR)/include/linux/usb*.h)
-+
-+endif
-+
-+clean:
-+ rm -rf *.o *.ko .*.cmd *.mod.c .*.o.d .*.o.tmp modules.order Module.markers Module.symvers .tmp_versions/
---- /dev/null
-+++ b/drivers/usb/host/dwc_common_port/Makefile.fbsd
-@@ -0,0 +1,17 @@
-+CFLAGS += -I/sys/i386/compile/GENERIC -I/sys/i386/include -I/usr/include
-+CFLAGS += -DDWC_FREEBSD
-+CFLAGS += -DDEBUG
-+#CFLAGS += -DDWC_DEBUG_REGS
-+#CFLAGS += -DDWC_DEBUG_MEMORY
-+
-+#CFLAGS += -DDWC_LIBMODULE
-+#CFLAGS += -DDWC_CCLIB
-+#CFLAGS += -DDWC_CRYPTOLIB
-+#CFLAGS += -DDWC_NOTIFYLIB
-+#CFLAGS += -DDWC_UTFLIB
-+
-+KMOD = dwc_common_port_lib
-+SRCS = dwc_cc.c dwc_modpow.c dwc_dh.c dwc_crypto.c dwc_notifier.c \
-+ dwc_common_fbsd.c dwc_mem.c
-+
-+.include <bsd.kmod.mk>
---- /dev/null
-+++ b/drivers/usb/host/dwc_common_port/Makefile.linux
-@@ -0,0 +1,49 @@
-+#
-+# Makefile for DWC_common library
-+#
-+ifneq ($(KERNELRELEASE),)
-+
-+ccflags-y += -DDWC_LINUX
-+#ccflags-y += -DDEBUG
-+#ccflags-y += -DDWC_DEBUG_REGS
-+#ccflags-y += -DDWC_DEBUG_MEMORY
-+
-+ccflags-y += -DDWC_LIBMODULE
-+ccflags-y += -DDWC_CCLIB
-+ccflags-y += -DDWC_CRYPTOLIB
-+ccflags-y += -DDWC_NOTIFYLIB
-+ccflags-y += -DDWC_UTFLIB
-+
-+obj-m := dwc_common_port_lib.o
-+dwc_common_port_lib-objs := dwc_cc.o dwc_modpow.o dwc_dh.o \
-+ dwc_crypto.o dwc_notifier.o \
-+ dwc_common_linux.o dwc_mem.o
-+
-+else
-+
-+ifeq ($(KDIR),)
-+$(error Must give "KDIR=/path/to/kernel/source" on command line or in environment)
-+endif
-+
-+ifeq ($(ARCH),)
-+$(error Must give "ARCH=<arch>" on command line or in environment. Also, if \
-+ cross-compiling, must give "CROSS_COMPILE=/path/to/compiler/plus/tool-prefix-")
-+endif
-+
-+ifeq ($(DOXYGEN),)
-+DOXYGEN := doxygen
-+endif
-+
-+default:
-+ $(MAKE) -C$(KDIR) M=$(PWD) ARCH=$(ARCH) CROSS_COMPILE=$(CROSS_COMPILE) modules
-+
-+docs: $(wildcard *.[hc]) doc/doxygen.cfg
-+ $(DOXYGEN) doc/doxygen.cfg
-+
-+tags: $(wildcard *.[hc])
-+ $(CTAGS) -e $(wildcard *.[hc]) $(wildcard linux/*.[hc]) $(wildcard $(KDIR)/include/linux/usb*.h)
-+
-+endif
-+
-+clean:
-+ rm -rf *.o *.ko .*.cmd *.mod.c .*.o.d .*.o.tmp modules.order Module.markers Module.symvers .tmp_versions/
---- /dev/null
-+++ b/drivers/usb/host/dwc_common_port/changes.txt
-@@ -0,0 +1,174 @@
-+
-+dwc_read_reg32() and friends now take an additional parameter, a pointer to an
-+IO context struct. The IO context struct should live in an os-dependent struct
-+in your driver. As an example, the dwc_usb3 driver has an os-dependent struct
-+named 'os_dep' embedded in the main device struct. So there these calls look
-+like this:
-+
-+ dwc_read_reg32(&usb3_dev->os_dep.ioctx, &pcd->dev_global_regs->dcfg);
-+
-+ dwc_write_reg32(&usb3_dev->os_dep.ioctx,
-+ &pcd->dev_global_regs->dcfg, 0);
-+
-+Note that for the existing Linux driver ports, it is not necessary to actually
-+define the 'ioctx' member in the os-dependent struct. Since Linux does not
-+require an IO context, its macros for dwc_read_reg32() and friends do not
-+use the context pointer, so it is optimized away by the compiler. But it is
-+necessary to add the pointer parameter to all of the call sites, to be ready
-+for any future ports (such as FreeBSD) which do require an IO context.
-+
-+
-+Similarly, dwc_alloc(), dwc_alloc_atomic(), dwc_strdup(), and dwc_free() now
-+take an additional parameter, a pointer to a memory context. Examples:
-+
-+ addr = dwc_alloc(&usb3_dev->os_dep.memctx, size);
-+
-+ dwc_free(&usb3_dev->os_dep.memctx, addr);
-+
-+Again, for the Linux ports, it is not necessary to actually define the memctx
-+member, but it is necessary to add the pointer parameter to all of the call
-+sites.
-+
-+
-+Same for dwc_dma_alloc() and dwc_dma_free(). Examples:
-+
-+ virt_addr = dwc_dma_alloc(&usb3_dev->os_dep.dmactx, size, &phys_addr);
-+
-+ dwc_dma_free(&usb3_dev->os_dep.dmactx, size, virt_addr, phys_addr);
-+
-+
-+Same for dwc_mutex_alloc() and dwc_mutex_free(). Examples:
-+
-+ mutex = dwc_mutex_alloc(&usb3_dev->os_dep.mtxctx);
-+
-+ dwc_mutex_free(&usb3_dev->os_dep.mtxctx, mutex);
-+
-+
-+Same for dwc_spinlock_alloc() and dwc_spinlock_free(). Examples:
-+
-+ lock = dwc_spinlock_alloc(&usb3_dev->osdep.splctx);
-+
-+ dwc_spinlock_free(&usb3_dev->osdep.splctx, lock);
-+
-+
-+Same for dwc_timer_alloc(). Example:
-+
-+ timer = dwc_timer_alloc(&usb3_dev->os_dep.tmrctx, "dwc_usb3_tmr1",
-+ cb_func, cb_data);
-+
-+
-+Same for dwc_waitq_alloc(). Example:
-+
-+ waitq = dwc_waitq_alloc(&usb3_dev->os_dep.wtqctx);
-+
-+
-+Same for dwc_thread_run(). Example:
-+
-+ thread = dwc_thread_run(&usb3_dev->os_dep.thdctx, func,
-+ "dwc_usb3_thd1", data);
-+
-+
-+Same for dwc_workq_alloc(). Example:
-+
-+ workq = dwc_workq_alloc(&usb3_dev->osdep.wkqctx, "dwc_usb3_wkq1");
-+
-+
-+Same for dwc_task_alloc(). Example:
-+
-+ task = dwc_task_alloc(&usb3_dev->os_dep.tskctx, "dwc_usb3_tsk1",
-+ cb_func, cb_data);
-+
-+
-+In addition to the context pointer additions, a few core functions have had
-+other changes made to their parameters:
-+
-+The 'flags' parameter to dwc_spinlock_irqsave() and dwc_spinunlock_irqrestore()
-+has been changed from a uint64_t to a dwc_irqflags_t.
-+
-+dwc_thread_should_stop() now takes a 'dwc_thread_t *' parameter, because the
-+FreeBSD equivalent of that function requires it.
-+
-+And, in addition to the context pointer, dwc_task_alloc() also adds a
-+'char *name' parameter, to be consistent with dwc_thread_run() and
-+dwc_workq_alloc(), and because the FreeBSD equivalent of that function
-+requires a unique name.
-+
-+
-+Here is a complete list of the core functions that now take a pointer to a
-+context as their first parameter:
-+
-+ dwc_read_reg32
-+ dwc_read_reg64
-+ dwc_write_reg32
-+ dwc_write_reg64
-+ dwc_modify_reg32
-+ dwc_modify_reg64
-+ dwc_alloc
-+ dwc_alloc_atomic
-+ dwc_strdup
-+ dwc_free
-+ dwc_dma_alloc
-+ dwc_dma_free
-+ dwc_mutex_alloc
-+ dwc_mutex_free
-+ dwc_spinlock_alloc
-+ dwc_spinlock_free
-+ dwc_timer_alloc
-+ dwc_waitq_alloc
-+ dwc_thread_run
-+ dwc_workq_alloc
-+ dwc_task_alloc Also adds a 'char *name' as its 2nd parameter
-+
-+And here are the core functions that have other changes to their parameters:
-+
-+ dwc_spinlock_irqsave 'flags' param is now a 'dwc_irqflags_t *'
-+ dwc_spinunlock_irqrestore 'flags' param is now a 'dwc_irqflags_t'
-+ dwc_thread_should_stop Adds a 'dwc_thread_t *' parameter
-+
-+
-+
-+The changes to the core functions also require some of the other library
-+functions to change:
-+
-+ dwc_cc_if_alloc() and dwc_cc_if_free() now take a 'void *memctx'
-+ (for memory allocation) as the 1st param and a 'void *mtxctx'
-+ (for mutex allocation) as the 2nd param.
-+
-+ dwc_cc_clear(), dwc_cc_add(), dwc_cc_change(), dwc_cc_remove(),
-+ dwc_cc_data_for_save(), and dwc_cc_restore_from_data() now take a
-+ 'void *memctx' as the 1st param.
-+
-+ dwc_dh_modpow(), dwc_dh_pk(), and dwc_dh_derive_keys() now take a
-+ 'void *memctx' as the 1st param.
-+
-+ dwc_modpow() now takes a 'void *memctx' as the 1st param.
-+
-+ dwc_alloc_notification_manager() now takes a 'void *memctx' as the
-+ 1st param and a 'void *wkqctx' (for work queue allocation) as the 2nd
-+ param, and also now returns an integer value that is non-zero if
-+ allocation of its data structures or work queue fails.
-+
-+ dwc_register_notifier() now takes a 'void *memctx' as the 1st param.
-+
-+ dwc_memory_debug_start() now takes a 'void *mem_ctx' as the first
-+ param, and also now returns an integer value that is non-zero if
-+ allocation of its data structures fails.
-+
-+
-+
-+Other miscellaneous changes:
-+
-+The DEBUG_MEMORY and DEBUG_REGS #define's have been renamed to
-+DWC_DEBUG_MEMORY and DWC_DEBUG_REGS.
-+
-+The following #define's have been added to allow selectively compiling library
-+features:
-+
-+ DWC_CCLIB
-+ DWC_CRYPTOLIB
-+ DWC_NOTIFYLIB
-+ DWC_UTFLIB
-+
-+A DWC_LIBMODULE #define has also been added. If this is not defined, then the
-+module code in dwc_common_linux.c is not compiled in. This allows linking the
-+library code directly into a driver module, instead of as a standalone module.
---- /dev/null
-+++ b/drivers/usb/host/dwc_common_port/doc/doxygen.cfg
-@@ -0,0 +1,270 @@
-+# Doxyfile 1.4.5
-+
-+#---------------------------------------------------------------------------
-+# Project related configuration options
-+#---------------------------------------------------------------------------
-+PROJECT_NAME = "Synopsys DWC Portability and Common Library for UWB"
-+PROJECT_NUMBER =
-+OUTPUT_DIRECTORY = doc
-+CREATE_SUBDIRS = NO
-+OUTPUT_LANGUAGE = English
-+BRIEF_MEMBER_DESC = YES
-+REPEAT_BRIEF = YES
-+ABBREVIATE_BRIEF = "The $name class" \
-+ "The $name widget" \
-+ "The $name file" \
-+ is \
-+ provides \
-+ specifies \
-+ contains \
-+ represents \
-+ a \
-+ an \
-+ the
-+ALWAYS_DETAILED_SEC = YES
-+INLINE_INHERITED_MEMB = NO
-+FULL_PATH_NAMES = NO
-+STRIP_FROM_PATH = ..
-+STRIP_FROM_INC_PATH =
-+SHORT_NAMES = NO
-+JAVADOC_AUTOBRIEF = YES
-+MULTILINE_CPP_IS_BRIEF = NO
-+DETAILS_AT_TOP = YES
-+INHERIT_DOCS = YES
-+SEPARATE_MEMBER_PAGES = NO
-+TAB_SIZE = 8
-+ALIASES =
-+OPTIMIZE_OUTPUT_FOR_C = YES
-+OPTIMIZE_OUTPUT_JAVA = NO
-+BUILTIN_STL_SUPPORT = NO
-+DISTRIBUTE_GROUP_DOC = NO
-+SUBGROUPING = NO
-+#---------------------------------------------------------------------------
-+# Build related configuration options
-+#---------------------------------------------------------------------------
-+EXTRACT_ALL = NO
-+EXTRACT_PRIVATE = NO
-+EXTRACT_STATIC = YES
-+EXTRACT_LOCAL_CLASSES = NO
-+EXTRACT_LOCAL_METHODS = NO
-+HIDE_UNDOC_MEMBERS = NO
-+HIDE_UNDOC_CLASSES = NO
-+HIDE_FRIEND_COMPOUNDS = NO
-+HIDE_IN_BODY_DOCS = NO
-+INTERNAL_DOCS = NO
-+CASE_SENSE_NAMES = YES
-+HIDE_SCOPE_NAMES = NO
-+SHOW_INCLUDE_FILES = NO
-+INLINE_INFO = YES
-+SORT_MEMBER_DOCS = NO
-+SORT_BRIEF_DOCS = NO
-+SORT_BY_SCOPE_NAME = NO
-+GENERATE_TODOLIST = YES
-+GENERATE_TESTLIST = YES
-+GENERATE_BUGLIST = YES
-+GENERATE_DEPRECATEDLIST= YES
-+ENABLED_SECTIONS =
-+MAX_INITIALIZER_LINES = 30
-+SHOW_USED_FILES = YES
-+SHOW_DIRECTORIES = YES
-+FILE_VERSION_FILTER =
-+#---------------------------------------------------------------------------
-+# configuration options related to warning and progress messages
-+#---------------------------------------------------------------------------
-+QUIET = YES
-+WARNINGS = YES
-+WARN_IF_UNDOCUMENTED = NO
-+WARN_IF_DOC_ERROR = YES
-+WARN_NO_PARAMDOC = YES
-+WARN_FORMAT = "$file:$line: $text"
-+WARN_LOGFILE =
-+#---------------------------------------------------------------------------
-+# configuration options related to the input files
-+#---------------------------------------------------------------------------
-+INPUT = .
-+FILE_PATTERNS = *.c \
-+ *.cc \
-+ *.cxx \
-+ *.cpp \
-+ *.c++ \
-+ *.d \
-+ *.java \
-+ *.ii \
-+ *.ixx \
-+ *.ipp \
-+ *.i++ \
-+ *.inl \
-+ *.h \
-+ *.hh \
-+ *.hxx \
-+ *.hpp \
-+ *.h++ \
-+ *.idl \
-+ *.odl \
-+ *.cs \
-+ *.php \
-+ *.php3 \
-+ *.inc \
-+ *.m \
-+ *.mm \
-+ *.dox \
-+ *.py \
-+ *.C \
-+ *.CC \
-+ *.C++ \
-+ *.II \
-+ *.I++ \
-+ *.H \
-+ *.HH \
-+ *.H++ \
-+ *.CS \
-+ *.PHP \
-+ *.PHP3 \
-+ *.M \
-+ *.MM \
-+ *.PY
-+RECURSIVE = NO
-+EXCLUDE =
-+EXCLUDE_SYMLINKS = NO
-+EXCLUDE_PATTERNS =
-+EXAMPLE_PATH =
-+EXAMPLE_PATTERNS = *
-+EXAMPLE_RECURSIVE = NO
-+IMAGE_PATH =
-+INPUT_FILTER =
-+FILTER_PATTERNS =
-+FILTER_SOURCE_FILES = NO
-+#---------------------------------------------------------------------------
-+# configuration options related to source browsing
-+#---------------------------------------------------------------------------
-+SOURCE_BROWSER = NO
-+INLINE_SOURCES = NO
-+STRIP_CODE_COMMENTS = YES
-+REFERENCED_BY_RELATION = YES
-+REFERENCES_RELATION = YES
-+USE_HTAGS = NO
-+VERBATIM_HEADERS = NO
-+#---------------------------------------------------------------------------
-+# configuration options related to the alphabetical class index
-+#---------------------------------------------------------------------------
-+ALPHABETICAL_INDEX = NO
-+COLS_IN_ALPHA_INDEX = 5
-+IGNORE_PREFIX =
-+#---------------------------------------------------------------------------
-+# configuration options related to the HTML output
-+#---------------------------------------------------------------------------
-+GENERATE_HTML = YES
-+HTML_OUTPUT = html
-+HTML_FILE_EXTENSION = .html
-+HTML_HEADER =
-+HTML_FOOTER =
-+HTML_STYLESHEET =
-+HTML_ALIGN_MEMBERS = YES
-+GENERATE_HTMLHELP = NO
-+CHM_FILE =
-+HHC_LOCATION =
-+GENERATE_CHI = NO
-+BINARY_TOC = NO
-+TOC_EXPAND = NO
-+DISABLE_INDEX = NO
-+ENUM_VALUES_PER_LINE = 4
-+GENERATE_TREEVIEW = YES
-+TREEVIEW_WIDTH = 250
-+#---------------------------------------------------------------------------
-+# configuration options related to the LaTeX output
-+#---------------------------------------------------------------------------
-+GENERATE_LATEX = NO
-+LATEX_OUTPUT = latex
-+LATEX_CMD_NAME = latex
-+MAKEINDEX_CMD_NAME = makeindex
-+COMPACT_LATEX = NO
-+PAPER_TYPE = a4wide
-+EXTRA_PACKAGES =
-+LATEX_HEADER =
-+PDF_HYPERLINKS = NO
-+USE_PDFLATEX = NO
-+LATEX_BATCHMODE = NO
-+LATEX_HIDE_INDICES = NO
-+#---------------------------------------------------------------------------
-+# configuration options related to the RTF output
-+#---------------------------------------------------------------------------
-+GENERATE_RTF = NO
-+RTF_OUTPUT = rtf
-+COMPACT_RTF = NO
-+RTF_HYPERLINKS = NO
-+RTF_STYLESHEET_FILE =
-+RTF_EXTENSIONS_FILE =
-+#---------------------------------------------------------------------------
-+# configuration options related to the man page output
-+#---------------------------------------------------------------------------
-+GENERATE_MAN = NO
-+MAN_OUTPUT = man
-+MAN_EXTENSION = .3
-+MAN_LINKS = NO
-+#---------------------------------------------------------------------------
-+# configuration options related to the XML output
-+#---------------------------------------------------------------------------
-+GENERATE_XML = NO
-+XML_OUTPUT = xml
-+XML_SCHEMA =
-+XML_DTD =
-+XML_PROGRAMLISTING = YES
-+#---------------------------------------------------------------------------
-+# configuration options for the AutoGen Definitions output
-+#---------------------------------------------------------------------------
-+GENERATE_AUTOGEN_DEF = NO
-+#---------------------------------------------------------------------------
-+# configuration options related to the Perl module output
-+#---------------------------------------------------------------------------
-+GENERATE_PERLMOD = NO
-+PERLMOD_LATEX = NO
-+PERLMOD_PRETTY = YES
-+PERLMOD_MAKEVAR_PREFIX =
-+#---------------------------------------------------------------------------
-+# Configuration options related to the preprocessor
-+#---------------------------------------------------------------------------
-+ENABLE_PREPROCESSING = YES
-+MACRO_EXPANSION = NO
-+EXPAND_ONLY_PREDEF = NO
-+SEARCH_INCLUDES = YES
-+INCLUDE_PATH =
-+INCLUDE_FILE_PATTERNS =
-+PREDEFINED = DEBUG DEBUG_MEMORY
-+EXPAND_AS_DEFINED =
-+SKIP_FUNCTION_MACROS = YES
-+#---------------------------------------------------------------------------
-+# Configuration::additions related to external references
-+#---------------------------------------------------------------------------
-+TAGFILES =
-+GENERATE_TAGFILE =
-+ALLEXTERNALS = NO
-+EXTERNAL_GROUPS = YES
-+PERL_PATH = /usr/bin/perl
-+#---------------------------------------------------------------------------
-+# Configuration options related to the dot tool
-+#---------------------------------------------------------------------------
-+CLASS_DIAGRAMS = YES
-+HIDE_UNDOC_RELATIONS = YES
-+HAVE_DOT = NO
-+CLASS_GRAPH = YES
-+COLLABORATION_GRAPH = YES
-+GROUP_GRAPHS = YES
-+UML_LOOK = NO
-+TEMPLATE_RELATIONS = NO
-+INCLUDE_GRAPH = NO
-+INCLUDED_BY_GRAPH = YES
-+CALL_GRAPH = NO
-+GRAPHICAL_HIERARCHY = YES
-+DIRECTORY_GRAPH = YES
-+DOT_IMAGE_FORMAT = png
-+DOT_PATH =
-+DOTFILE_DIRS =
-+MAX_DOT_GRAPH_DEPTH = 1000
-+DOT_TRANSPARENT = NO
-+DOT_MULTI_TARGETS = NO
-+GENERATE_LEGEND = YES
-+DOT_CLEANUP = YES
-+#---------------------------------------------------------------------------
-+# Configuration::additions related to the search engine
-+#---------------------------------------------------------------------------
-+SEARCHENGINE = NO
---- /dev/null
-+++ b/drivers/usb/host/dwc_common_port/dwc_cc.c
-@@ -0,0 +1,532 @@
-+/* =========================================================================
-+ * $File: //dwh/usb_iip/dev/software/dwc_common_port_2/dwc_cc.c $
-+ * $Revision: #4 $
-+ * $Date: 2010/11/04 $
-+ * $Change: 1621692 $
-+ *
-+ * Synopsys Portability Library Software and documentation
-+ * (hereinafter, "Software") is an Unsupported proprietary work of
-+ * Synopsys, Inc. unless otherwise expressly agreed to in writing
-+ * between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product
-+ * under any End User Software License Agreement or Agreement for
-+ * Licensed Product with Synopsys or any supplement thereto. You are
-+ * permitted to use and redistribute this Software in source and binary
-+ * forms, with or without modification, provided that redistributions
-+ * of source code must retain this notice. You may not view, use,
-+ * disclose, copy or distribute this file or any information contained
-+ * herein except pursuant to this license grant from Synopsys. If you
-+ * do not agree with this notice, including the disclaimer below, then
-+ * you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS"
-+ * BASIS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
-+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
-+ * FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. IN NO EVENT SHALL
-+ * SYNOPSYS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY
-+ * OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
-+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
-+ * USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================= */
-+#ifdef DWC_CCLIB
-+
-+#include "dwc_cc.h"
-+
-+typedef struct dwc_cc
-+{
-+ uint32_t uid;
-+ uint8_t chid[16];
-+ uint8_t cdid[16];
-+ uint8_t ck[16];
-+ uint8_t *name;
-+ uint8_t length;
-+ DWC_CIRCLEQ_ENTRY(dwc_cc) list_entry;
-+} dwc_cc_t;
-+
-+DWC_CIRCLEQ_HEAD(context_list, dwc_cc);
-+
-+/** The main structure for CC management. */
-+struct dwc_cc_if
-+{
-+ dwc_mutex_t *mutex;
-+ char *filename;
-+
-+ unsigned is_host:1;
-+
-+ dwc_notifier_t *notifier;
-+
-+ struct context_list list;
-+};
-+
-+#ifdef DEBUG
-+static inline void dump_bytes(char *name, uint8_t *bytes, int len)
-+{
-+ int i;
-+ DWC_PRINTF("%s: ", name);
-+ for (i=0; i<len; i++) {
-+ DWC_PRINTF("%02x ", bytes[i]);
-+ }
-+ DWC_PRINTF("\n");
-+}
-+#else
-+#define dump_bytes(x...)
-+#endif
-+
-+static dwc_cc_t *alloc_cc(void *mem_ctx, uint8_t *name, uint32_t length)
-+{
-+ dwc_cc_t *cc = dwc_alloc(mem_ctx, sizeof(dwc_cc_t));
-+ if (!cc) {
-+ return NULL;
-+ }
-+ DWC_MEMSET(cc, 0, sizeof(dwc_cc_t));
-+
-+ if (name) {
-+ cc->length = length;
-+ cc->name = dwc_alloc(mem_ctx, length);
-+ if (!cc->name) {
-+ dwc_free(mem_ctx, cc);
-+ return NULL;
-+ }
-+
-+ DWC_MEMCPY(cc->name, name, length);
-+ }
-+
-+ return cc;
-+}
-+
-+static void free_cc(void *mem_ctx, dwc_cc_t *cc)
-+{
-+ if (cc->name) {
-+ dwc_free(mem_ctx, cc->name);
-+ }
-+ dwc_free(mem_ctx, cc);
-+}
-+
-+static uint32_t next_uid(dwc_cc_if_t *cc_if)
-+{
-+ uint32_t uid = 0;
-+ dwc_cc_t *cc;
-+ DWC_CIRCLEQ_FOREACH(cc, &cc_if->list, list_entry) {
-+ if (cc->uid > uid) {
-+ uid = cc->uid;
-+ }
-+ }
-+
-+ if (uid == 0) {
-+ uid = 255;
-+ }
-+
-+ return uid + 1;
-+}
-+
-+static dwc_cc_t *cc_find(dwc_cc_if_t *cc_if, uint32_t uid)
-+{
-+ dwc_cc_t *cc;
-+ DWC_CIRCLEQ_FOREACH(cc, &cc_if->list, list_entry) {
-+ if (cc->uid == uid) {
-+ return cc;
-+ }
-+ }
-+ return NULL;
-+}
-+
-+static unsigned int cc_data_size(dwc_cc_if_t *cc_if)
-+{
-+ unsigned int size = 0;
-+ dwc_cc_t *cc;
-+ DWC_CIRCLEQ_FOREACH(cc, &cc_if->list, list_entry) {
-+ size += (48 + 1);
-+ if (cc->name) {
-+ size += cc->length;
-+ }
-+ }
-+ return size;
-+}
-+
-+static uint32_t cc_match_chid(dwc_cc_if_t *cc_if, uint8_t *chid)
-+{
-+ uint32_t uid = 0;
-+ dwc_cc_t *cc;
-+
-+ DWC_CIRCLEQ_FOREACH(cc, &cc_if->list, list_entry) {
-+ if (DWC_MEMCMP(cc->chid, chid, 16) == 0) {
-+ uid = cc->uid;
-+ break;
-+ }
-+ }
-+ return uid;
-+}
-+static uint32_t cc_match_cdid(dwc_cc_if_t *cc_if, uint8_t *cdid)
-+{
-+ uint32_t uid = 0;
-+ dwc_cc_t *cc;
-+
-+ DWC_CIRCLEQ_FOREACH(cc, &cc_if->list, list_entry) {
-+ if (DWC_MEMCMP(cc->cdid, cdid, 16) == 0) {
-+ uid = cc->uid;
-+ break;
-+ }
-+ }
-+ return uid;
-+}
-+
-+/* Internal cc_add */
-+static int32_t cc_add(void *mem_ctx, dwc_cc_if_t *cc_if, uint8_t *chid,
-+ uint8_t *cdid, uint8_t *ck, uint8_t *name, uint8_t length)
-+{
-+ dwc_cc_t *cc;
-+ uint32_t uid;
-+
-+ if (cc_if->is_host) {
-+ uid = cc_match_cdid(cc_if, cdid);
-+ }
-+ else {
-+ uid = cc_match_chid(cc_if, chid);
-+ }
-+
-+ if (uid) {
-+ DWC_DEBUGC("Replacing previous connection context id=%d name=%p name_len=%d", uid, name, length);
-+ cc = cc_find(cc_if, uid);
-+ }
-+ else {
-+ cc = alloc_cc(mem_ctx, name, length);
-+ cc->uid = next_uid(cc_if);
-+ DWC_CIRCLEQ_INSERT_TAIL(&cc_if->list, cc, list_entry);
-+ }
-+
-+ DWC_MEMCPY(&(cc->chid[0]), chid, 16);
-+ DWC_MEMCPY(&(cc->cdid[0]), cdid, 16);
-+ DWC_MEMCPY(&(cc->ck[0]), ck, 16);
-+
-+ DWC_DEBUGC("Added connection context id=%d name=%p name_len=%d", cc->uid, name, length);
-+ dump_bytes("CHID", cc->chid, 16);
-+ dump_bytes("CDID", cc->cdid, 16);
-+ dump_bytes("CK", cc->ck, 16);
-+ return cc->uid;
-+}
-+
-+/* Internal cc_clear */
-+static void cc_clear(void *mem_ctx, dwc_cc_if_t *cc_if)
-+{
-+ while (!DWC_CIRCLEQ_EMPTY(&cc_if->list)) {
-+ dwc_cc_t *cc = DWC_CIRCLEQ_FIRST(&cc_if->list);
-+ DWC_CIRCLEQ_REMOVE_INIT(&cc_if->list, cc, list_entry);
-+ free_cc(mem_ctx, cc);
-+ }
-+}
-+
-+dwc_cc_if_t *dwc_cc_if_alloc(void *mem_ctx, void *mtx_ctx,
-+ dwc_notifier_t *notifier, unsigned is_host)
-+{
-+ dwc_cc_if_t *cc_if = NULL;
-+
-+ /* Allocate a common_cc_if structure */
-+ cc_if = dwc_alloc(mem_ctx, sizeof(dwc_cc_if_t));
-+
-+ if (!cc_if)
-+ return NULL;
-+
-+#if (defined(DWC_LINUX) && defined(CONFIG_DEBUG_MUTEXES))
-+ DWC_MUTEX_ALLOC_LINUX_DEBUG(cc_if->mutex);
-+#else
-+ cc_if->mutex = dwc_mutex_alloc(mtx_ctx);
-+#endif
-+ if (!cc_if->mutex) {
-+ dwc_free(mem_ctx, cc_if);
-+ return NULL;
-+ }
-+
-+ DWC_CIRCLEQ_INIT(&cc_if->list);
-+ cc_if->is_host = is_host;
-+ cc_if->notifier = notifier;
-+ return cc_if;
-+}
-+
-+void dwc_cc_if_free(void *mem_ctx, void *mtx_ctx, dwc_cc_if_t *cc_if)
-+{
-+#if (defined(DWC_LINUX) && defined(CONFIG_DEBUG_MUTEXES))
-+ DWC_MUTEX_FREE(cc_if->mutex);
-+#else
-+ dwc_mutex_free(mtx_ctx, cc_if->mutex);
-+#endif
-+ cc_clear(mem_ctx, cc_if);
-+ dwc_free(mem_ctx, cc_if);
-+}
-+
-+static void cc_changed(dwc_cc_if_t *cc_if)
-+{
-+ if (cc_if->notifier) {
-+ dwc_notify(cc_if->notifier, DWC_CC_LIST_CHANGED_NOTIFICATION, cc_if);
-+ }
-+}
-+
-+void dwc_cc_clear(void *mem_ctx, dwc_cc_if_t *cc_if)
-+{
-+ DWC_MUTEX_LOCK(cc_if->mutex);
-+ cc_clear(mem_ctx, cc_if);
-+ DWC_MUTEX_UNLOCK(cc_if->mutex);
-+ cc_changed(cc_if);
-+}
-+
-+int32_t dwc_cc_add(void *mem_ctx, dwc_cc_if_t *cc_if, uint8_t *chid,
-+ uint8_t *cdid, uint8_t *ck, uint8_t *name, uint8_t length)
-+{
-+ uint32_t uid;
-+
-+ DWC_MUTEX_LOCK(cc_if->mutex);
-+ uid = cc_add(mem_ctx, cc_if, chid, cdid, ck, name, length);
-+ DWC_MUTEX_UNLOCK(cc_if->mutex);
-+ cc_changed(cc_if);
-+
-+ return uid;
-+}
-+
-+void dwc_cc_change(void *mem_ctx, dwc_cc_if_t *cc_if, int32_t id, uint8_t *chid,
-+ uint8_t *cdid, uint8_t *ck, uint8_t *name, uint8_t length)
-+{
-+ dwc_cc_t* cc;
-+
-+ DWC_DEBUGC("Change connection context %d", id);
-+
-+ DWC_MUTEX_LOCK(cc_if->mutex);
-+ cc = cc_find(cc_if, id);
-+ if (!cc) {
-+ DWC_ERROR("Uid %d not found in cc list\n", id);
-+ DWC_MUTEX_UNLOCK(cc_if->mutex);
-+ return;
-+ }
-+
-+ if (chid) {
-+ DWC_MEMCPY(&(cc->chid[0]), chid, 16);
-+ }
-+ if (cdid) {
-+ DWC_MEMCPY(&(cc->cdid[0]), cdid, 16);
-+ }
-+ if (ck) {
-+ DWC_MEMCPY(&(cc->ck[0]), ck, 16);
-+ }
-+
-+ if (name) {
-+ if (cc->name) {
-+ dwc_free(mem_ctx, cc->name);
-+ }
-+ cc->name = dwc_alloc(mem_ctx, length);
-+ if (!cc->name) {
-+ DWC_ERROR("Out of memory in dwc_cc_change()\n");
-+ DWC_MUTEX_UNLOCK(cc_if->mutex);
-+ return;
-+ }
-+ cc->length = length;
-+ DWC_MEMCPY(cc->name, name, length);
-+ }
-+
-+ DWC_MUTEX_UNLOCK(cc_if->mutex);
-+
-+ cc_changed(cc_if);
-+
-+ DWC_DEBUGC("Changed connection context id=%d\n", id);
-+ dump_bytes("New CHID", cc->chid, 16);
-+ dump_bytes("New CDID", cc->cdid, 16);
-+ dump_bytes("New CK", cc->ck, 16);
-+}
-+
-+void dwc_cc_remove(void *mem_ctx, dwc_cc_if_t *cc_if, int32_t id)
-+{
-+ dwc_cc_t *cc;
-+
-+ DWC_DEBUGC("Removing connection context %d", id);
-+
-+ DWC_MUTEX_LOCK(cc_if->mutex);
-+ cc = cc_find(cc_if, id);
-+ if (!cc) {
-+ DWC_ERROR("Uid %d not found in cc list\n", id);
-+ DWC_MUTEX_UNLOCK(cc_if->mutex);
-+ return;
-+ }
-+
-+ DWC_CIRCLEQ_REMOVE_INIT(&cc_if->list, cc, list_entry);
-+ DWC_MUTEX_UNLOCK(cc_if->mutex);
-+ free_cc(mem_ctx, cc);
-+
-+ cc_changed(cc_if);
-+}
-+
-+uint8_t *dwc_cc_data_for_save(void *mem_ctx, dwc_cc_if_t *cc_if, unsigned int *length)
-+{
-+ uint8_t *buf, *x;
-+ uint8_t zero = 0;
-+ dwc_cc_t *cc;
-+
-+ DWC_MUTEX_LOCK(cc_if->mutex);
-+ *length = cc_data_size(cc_if);
-+ if (!(*length)) {
-+ DWC_MUTEX_UNLOCK(cc_if->mutex);
-+ return NULL;
-+ }
-+
-+ DWC_DEBUGC("Creating data for saving (length=%d)", *length);
-+
-+ buf = dwc_alloc(mem_ctx, *length);
-+ if (!buf) {
-+ *length = 0;
-+ DWC_MUTEX_UNLOCK(cc_if->mutex);
-+ return NULL;
-+ }
-+
-+ x = buf;
-+ DWC_CIRCLEQ_FOREACH(cc, &cc_if->list, list_entry) {
-+ DWC_MEMCPY(x, cc->chid, 16);
-+ x += 16;
-+ DWC_MEMCPY(x, cc->cdid, 16);
-+ x += 16;
-+ DWC_MEMCPY(x, cc->ck, 16);
-+ x += 16;
-+ if (cc->name) {
-+ DWC_MEMCPY(x, &cc->length, 1);
-+ x += 1;
-+ DWC_MEMCPY(x, cc->name, cc->length);
-+ x += cc->length;
-+ }
-+ else {
-+ DWC_MEMCPY(x, &zero, 1);
-+ x += 1;
-+ }
-+ }
-+ DWC_MUTEX_UNLOCK(cc_if->mutex);
-+
-+ return buf;
-+}
-+
-+void dwc_cc_restore_from_data(void *mem_ctx, dwc_cc_if_t *cc_if, uint8_t *data, uint32_t length)
-+{
-+ uint8_t name_length;
-+ uint8_t *name;
-+ uint8_t *chid;
-+ uint8_t *cdid;
-+ uint8_t *ck;
-+ uint32_t i = 0;
-+
-+ DWC_MUTEX_LOCK(cc_if->mutex);
-+ cc_clear(mem_ctx, cc_if);
-+
-+ while (i < length) {
-+ chid = &data[i];
-+ i += 16;
-+ cdid = &data[i];
-+ i += 16;
-+ ck = &data[i];
-+ i += 16;
-+
-+ name_length = data[i];
-+ i ++;
-+
-+ if (name_length) {
-+ name = &data[i];
-+ i += name_length;
-+ }
-+ else {
-+ name = NULL;
-+ }
-+
-+ /* check to see if we haven't overflown the buffer */
-+ if (i > length) {
-+ DWC_ERROR("Data format error while attempting to load CCs "
-+ "(nlen=%d, iter=%d, buflen=%d).\n", name_length, i, length);
-+ break;
-+ }
-+
-+ cc_add(mem_ctx, cc_if, chid, cdid, ck, name, name_length);
-+ }
-+ DWC_MUTEX_UNLOCK(cc_if->mutex);
-+
-+ cc_changed(cc_if);
-+}
-+
-+uint32_t dwc_cc_match_chid(dwc_cc_if_t *cc_if, uint8_t *chid)
-+{
-+ uint32_t uid = 0;
-+
-+ DWC_MUTEX_LOCK(cc_if->mutex);
-+ uid = cc_match_chid(cc_if, chid);
-+ DWC_MUTEX_UNLOCK(cc_if->mutex);
-+ return uid;
-+}
-+uint32_t dwc_cc_match_cdid(dwc_cc_if_t *cc_if, uint8_t *cdid)
-+{
-+ uint32_t uid = 0;
-+
-+ DWC_MUTEX_LOCK(cc_if->mutex);
-+ uid = cc_match_cdid(cc_if, cdid);
-+ DWC_MUTEX_UNLOCK(cc_if->mutex);
-+ return uid;
-+}
-+
-+uint8_t *dwc_cc_ck(dwc_cc_if_t *cc_if, int32_t id)
-+{
-+ uint8_t *ck = NULL;
-+ dwc_cc_t *cc;
-+
-+ DWC_MUTEX_LOCK(cc_if->mutex);
-+ cc = cc_find(cc_if, id);
-+ if (cc) {
-+ ck = cc->ck;
-+ }
-+ DWC_MUTEX_UNLOCK(cc_if->mutex);
-+
-+ return ck;
-+
-+}
-+
-+uint8_t *dwc_cc_chid(dwc_cc_if_t *cc_if, int32_t id)
-+{
-+ uint8_t *retval = NULL;
-+ dwc_cc_t *cc;
-+
-+ DWC_MUTEX_LOCK(cc_if->mutex);
-+ cc = cc_find(cc_if, id);
-+ if (cc) {
-+ retval = cc->chid;
-+ }
-+ DWC_MUTEX_UNLOCK(cc_if->mutex);
-+
-+ return retval;
-+}
-+
-+uint8_t *dwc_cc_cdid(dwc_cc_if_t *cc_if, int32_t id)
-+{
-+ uint8_t *retval = NULL;
-+ dwc_cc_t *cc;
-+
-+ DWC_MUTEX_LOCK(cc_if->mutex);
-+ cc = cc_find(cc_if, id);
-+ if (cc) {
-+ retval = cc->cdid;
-+ }
-+ DWC_MUTEX_UNLOCK(cc_if->mutex);
-+
-+ return retval;
-+}
-+
-+uint8_t *dwc_cc_name(dwc_cc_if_t *cc_if, int32_t id, uint8_t *length)
-+{
-+ uint8_t *retval = NULL;
-+ dwc_cc_t *cc;
-+
-+ DWC_MUTEX_LOCK(cc_if->mutex);
-+ *length = 0;
-+ cc = cc_find(cc_if, id);
-+ if (cc) {
-+ *length = cc->length;
-+ retval = cc->name;
-+ }
-+ DWC_MUTEX_UNLOCK(cc_if->mutex);
-+
-+ return retval;
-+}
-+
-+#endif /* DWC_CCLIB */
---- /dev/null
-+++ b/drivers/usb/host/dwc_common_port/dwc_cc.h
-@@ -0,0 +1,224 @@
-+/* =========================================================================
-+ * $File: //dwh/usb_iip/dev/software/dwc_common_port_2/dwc_cc.h $
-+ * $Revision: #4 $
-+ * $Date: 2010/09/28 $
-+ * $Change: 1596182 $
-+ *
-+ * Synopsys Portability Library Software and documentation
-+ * (hereinafter, "Software") is an Unsupported proprietary work of
-+ * Synopsys, Inc. unless otherwise expressly agreed to in writing
-+ * between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product
-+ * under any End User Software License Agreement or Agreement for
-+ * Licensed Product with Synopsys or any supplement thereto. You are
-+ * permitted to use and redistribute this Software in source and binary
-+ * forms, with or without modification, provided that redistributions
-+ * of source code must retain this notice. You may not view, use,
-+ * disclose, copy or distribute this file or any information contained
-+ * herein except pursuant to this license grant from Synopsys. If you
-+ * do not agree with this notice, including the disclaimer below, then
-+ * you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS"
-+ * BASIS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
-+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
-+ * FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. IN NO EVENT SHALL
-+ * SYNOPSYS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY
-+ * OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
-+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
-+ * USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================= */
-+#ifndef _DWC_CC_H_
-+#define _DWC_CC_H_
-+
-+#ifdef __cplusplus
-+extern "C" {
-+#endif
-+
-+/** @file
-+ *
-+ * This file defines the Context Context library.
-+ *
-+ * The main data structure is dwc_cc_if_t which is returned by either the
-+ * dwc_cc_if_alloc function or returned by the module to the user via a provided
-+ * function. The data structure is opaque and should only be manipulated via the
-+ * functions provied in this API.
-+ *
-+ * It manages a list of connection contexts and operations can be performed to
-+ * add, remove, query, search, and change, those contexts. Additionally,
-+ * a dwc_notifier_t object can be requested from the manager so that
-+ * the user can be notified whenever the context list has changed.
-+ */
-+
-+#include "dwc_os.h"
-+#include "dwc_list.h"
-+#include "dwc_notifier.h"
-+
-+
-+/* Notifications */
-+#define DWC_CC_LIST_CHANGED_NOTIFICATION "DWC_CC_LIST_CHANGED_NOTIFICATION"
-+
-+struct dwc_cc_if;
-+typedef struct dwc_cc_if dwc_cc_if_t;
-+
-+
-+/** @name Connection Context Operations */
-+/** @{ */
-+
-+/** This function allocates memory for a dwc_cc_if_t structure, initializes
-+ * fields to default values, and returns a pointer to the structure or NULL on
-+ * error. */
-+extern dwc_cc_if_t *dwc_cc_if_alloc(void *mem_ctx, void *mtx_ctx,
-+ dwc_notifier_t *notifier, unsigned is_host);
-+
-+/** Frees the memory for the specified CC structure allocated from
-+ * dwc_cc_if_alloc(). */
-+extern void dwc_cc_if_free(void *mem_ctx, void *mtx_ctx, dwc_cc_if_t *cc_if);
-+
-+/** Removes all contexts from the connection context list */
-+extern void dwc_cc_clear(void *mem_ctx, dwc_cc_if_t *cc_if);
-+
-+/** Adds a connection context (CHID, CK, CDID, Name) to the connection context list.
-+ * If a CHID already exists, the CK and name are overwritten. Statistics are
-+ * not overwritten.
-+ *
-+ * @param cc_if The cc_if structure.
-+ * @param chid A pointer to the 16-byte CHID. This value will be copied.
-+ * @param ck A pointer to the 16-byte CK. This value will be copied.
-+ * @param cdid A pointer to the 16-byte CDID. This value will be copied.
-+ * @param name An optional host friendly name as defined in the association model
-+ * spec. Must be a UTF16-LE unicode string. Can be NULL to indicated no name.
-+ * @param length The length othe unicode string.
-+ * @return A unique identifier used to refer to this context that is valid for
-+ * as long as this context is still in the list. */
-+extern int32_t dwc_cc_add(void *mem_ctx, dwc_cc_if_t *cc_if, uint8_t *chid,
-+ uint8_t *cdid, uint8_t *ck, uint8_t *name,
-+ uint8_t length);
-+
-+/** Changes the CHID, CK, CDID, or Name values of a connection context in the
-+ * list, preserving any accumulated statistics. This would typically be called
-+ * if the host decideds to change the context with a SET_CONNECTION request.
-+ *
-+ * @param cc_if The cc_if structure.
-+ * @param id The identifier of the connection context.
-+ * @param chid A pointer to the 16-byte CHID. This value will be copied. NULL
-+ * indicates no change.
-+ * @param cdid A pointer to the 16-byte CDID. This value will be copied. NULL
-+ * indicates no change.
-+ * @param ck A pointer to the 16-byte CK. This value will be copied. NULL
-+ * indicates no change.
-+ * @param name Host friendly name UTF16-LE. NULL indicates no change.
-+ * @param length Length of name. */
-+extern void dwc_cc_change(void *mem_ctx, dwc_cc_if_t *cc_if, int32_t id,
-+ uint8_t *chid, uint8_t *cdid, uint8_t *ck,
-+ uint8_t *name, uint8_t length);
-+
-+/** Remove the specified connection context.
-+ * @param cc_if The cc_if structure.
-+ * @param id The identifier of the connection context to remove. */
-+extern void dwc_cc_remove(void *mem_ctx, dwc_cc_if_t *cc_if, int32_t id);
-+
-+/** Get a binary block of data for the connection context list and attributes.
-+ * This data can be used by the OS specific driver to save the connection
-+ * context list into non-volatile memory.
-+ *
-+ * @param cc_if The cc_if structure.
-+ * @param length Return the length of the data buffer.
-+ * @return A pointer to the data buffer. The memory for this buffer should be
-+ * freed with DWC_FREE() after use. */
-+extern uint8_t *dwc_cc_data_for_save(void *mem_ctx, dwc_cc_if_t *cc_if,
-+ unsigned int *length);
-+
-+/** Restore the connection context list from the binary data that was previously
-+ * returned from a call to dwc_cc_data_for_save. This can be used by the OS specific
-+ * driver to load a connection context list from non-volatile memory.
-+ *
-+ * @param cc_if The cc_if structure.
-+ * @param data The data bytes as returned from dwc_cc_data_for_save.
-+ * @param length The length of the data. */
-+extern void dwc_cc_restore_from_data(void *mem_ctx, dwc_cc_if_t *cc_if,
-+ uint8_t *data, unsigned int length);
-+
-+/** Find the connection context from the specified CHID.
-+ *
-+ * @param cc_if The cc_if structure.
-+ * @param chid A pointer to the CHID data.
-+ * @return A non-zero identifier of the connection context if the CHID matches.
-+ * Otherwise returns 0. */
-+extern uint32_t dwc_cc_match_chid(dwc_cc_if_t *cc_if, uint8_t *chid);
-+
-+/** Find the connection context from the specified CDID.
-+ *
-+ * @param cc_if The cc_if structure.
-+ * @param cdid A pointer to the CDID data.
-+ * @return A non-zero identifier of the connection context if the CHID matches.
-+ * Otherwise returns 0. */
-+extern uint32_t dwc_cc_match_cdid(dwc_cc_if_t *cc_if, uint8_t *cdid);
-+
-+/** Retrieve the CK from the specified connection context.
-+ *
-+ * @param cc_if The cc_if structure.
-+ * @param id The identifier of the connection context.
-+ * @return A pointer to the CK data. The memory does not need to be freed. */
-+extern uint8_t *dwc_cc_ck(dwc_cc_if_t *cc_if, int32_t id);
-+
-+/** Retrieve the CHID from the specified connection context.
-+ *
-+ * @param cc_if The cc_if structure.
-+ * @param id The identifier of the connection context.
-+ * @return A pointer to the CHID data. The memory does not need to be freed. */
-+extern uint8_t *dwc_cc_chid(dwc_cc_if_t *cc_if, int32_t id);
-+
-+/** Retrieve the CDID from the specified connection context.
-+ *
-+ * @param cc_if The cc_if structure.
-+ * @param id The identifier of the connection context.
-+ * @return A pointer to the CDID data. The memory does not need to be freed. */
-+extern uint8_t *dwc_cc_cdid(dwc_cc_if_t *cc_if, int32_t id);
-+
-+extern uint8_t *dwc_cc_name(dwc_cc_if_t *cc_if, int32_t id, uint8_t *length);
-+
-+/** Checks a buffer for non-zero.
-+ * @param id A pointer to a 16 byte buffer.
-+ * @return true if the 16 byte value is non-zero. */
-+static inline unsigned dwc_assoc_is_not_zero_id(uint8_t *id) {
-+ int i;
-+ for (i=0; i<16; i++) {
-+ if (id[i]) return 1;
-+ }
-+ return 0;
-+}
-+
-+/** Checks a buffer for zero.
-+ * @param id A pointer to a 16 byte buffer.
-+ * @return true if the 16 byte value is zero. */
-+static inline unsigned dwc_assoc_is_zero_id(uint8_t *id) {
-+ return !dwc_assoc_is_not_zero_id(id);
-+}
-+
-+/** Prints an ASCII representation for the 16-byte chid, cdid, or ck, into
-+ * buffer. */
-+static inline int dwc_print_id_string(char *buffer, uint8_t *id) {
-+ char *ptr = buffer;
-+ int i;
-+ for (i=0; i<16; i++) {
-+ ptr += DWC_SPRINTF(ptr, "%02x", id[i]);
-+ if (i < 15) {
-+ ptr += DWC_SPRINTF(ptr, " ");
-+ }
-+ }
-+ return ptr - buffer;
-+}
-+
-+/** @} */
-+
-+#ifdef __cplusplus
-+}
-+#endif
-+
-+#endif /* _DWC_CC_H_ */
---- /dev/null
-+++ b/drivers/usb/host/dwc_common_port/dwc_common_fbsd.c
-@@ -0,0 +1,1308 @@
-+#include "dwc_os.h"
-+#include "dwc_list.h"
-+
-+#ifdef DWC_CCLIB
-+# include "dwc_cc.h"
-+#endif
-+
-+#ifdef DWC_CRYPTOLIB
-+# include "dwc_modpow.h"
-+# include "dwc_dh.h"
-+# include "dwc_crypto.h"
-+#endif
-+
-+#ifdef DWC_NOTIFYLIB
-+# include "dwc_notifier.h"
-+#endif
-+
-+/* OS-Level Implementations */
-+
-+/* This is the FreeBSD 7.0 kernel implementation of the DWC platform library. */
-+
-+
-+/* MISC */
-+
-+void *DWC_MEMSET(void *dest, uint8_t byte, uint32_t size)
-+{
-+ return memset(dest, byte, size);
-+}
-+
-+void *DWC_MEMCPY(void *dest, void const *src, uint32_t size)
-+{
-+ return memcpy(dest, src, size);
-+}
-+
-+void *DWC_MEMMOVE(void *dest, void *src, uint32_t size)
-+{
-+ bcopy(src, dest, size);
-+ return dest;
-+}
-+
-+int DWC_MEMCMP(void *m1, void *m2, uint32_t size)
-+{
-+ return memcmp(m1, m2, size);
-+}
-+
-+int DWC_STRNCMP(void *s1, void *s2, uint32_t size)
-+{
-+ return strncmp(s1, s2, size);
-+}
-+
-+int DWC_STRCMP(void *s1, void *s2)
-+{
-+ return strcmp(s1, s2);
-+}
-+
-+int DWC_STRLEN(char const *str)
-+{
-+ return strlen(str);
-+}
-+
-+char *DWC_STRCPY(char *to, char const *from)
-+{
-+ return strcpy(to, from);
-+}
-+
-+char *DWC_STRDUP(char const *str)
-+{
-+ int len = DWC_STRLEN(str) + 1;
-+ char *new = DWC_ALLOC_ATOMIC(len);
-+
-+ if (!new) {
-+ return NULL;
-+ }
-+
-+ DWC_MEMCPY(new, str, len);
-+ return new;
-+}
-+
-+int DWC_ATOI(char *str, int32_t *value)
-+{
-+ char *end = NULL;
-+
-+ *value = strtol(str, &end, 0);
-+ if (*end == '\0') {
-+ return 0;
-+ }
-+
-+ return -1;
-+}
-+
-+int DWC_ATOUI(char *str, uint32_t *value)
-+{
-+ char *end = NULL;
-+
-+ *value = strtoul(str, &end, 0);
-+ if (*end == '\0') {
-+ return 0;
-+ }
-+
-+ return -1;
-+}
-+
-+
-+#ifdef DWC_UTFLIB
-+/* From usbstring.c */
-+
-+int DWC_UTF8_TO_UTF16LE(uint8_t const *s, uint16_t *cp, unsigned len)
-+{
-+ int count = 0;
-+ u8 c;
-+ u16 uchar;
-+
-+ /* this insists on correct encodings, though not minimal ones.
-+ * BUT it currently rejects legit 4-byte UTF-8 code points,
-+ * which need surrogate pairs. (Unicode 3.1 can use them.)
-+ */
-+ while (len != 0 && (c = (u8) *s++) != 0) {
-+ if (unlikely(c & 0x80)) {
-+ // 2-byte sequence:
-+ // 00000yyyyyxxxxxx = 110yyyyy 10xxxxxx
-+ if ((c & 0xe0) == 0xc0) {
-+ uchar = (c & 0x1f) << 6;
-+
-+ c = (u8) *s++;
-+ if ((c & 0xc0) != 0xc0)
-+ goto fail;
-+ c &= 0x3f;
-+ uchar |= c;
-+
-+ // 3-byte sequence (most CJKV characters):
-+ // zzzzyyyyyyxxxxxx = 1110zzzz 10yyyyyy 10xxxxxx
-+ } else if ((c & 0xf0) == 0xe0) {
-+ uchar = (c & 0x0f) << 12;
-+
-+ c = (u8) *s++;
-+ if ((c & 0xc0) != 0xc0)
-+ goto fail;
-+ c &= 0x3f;
-+ uchar |= c << 6;
-+
-+ c = (u8) *s++;
-+ if ((c & 0xc0) != 0xc0)
-+ goto fail;
-+ c &= 0x3f;
-+ uchar |= c;
-+
-+ /* no bogus surrogates */
-+ if (0xd800 <= uchar && uchar <= 0xdfff)
-+ goto fail;
-+
-+ // 4-byte sequence (surrogate pairs, currently rare):
-+ // 11101110wwwwzzzzyy + 110111yyyyxxxxxx
-+ // = 11110uuu 10uuzzzz 10yyyyyy 10xxxxxx
-+ // (uuuuu = wwww + 1)
-+ // FIXME accept the surrogate code points (only)
-+ } else
-+ goto fail;
-+ } else
-+ uchar = c;
-+ put_unaligned (cpu_to_le16 (uchar), cp++);
-+ count++;
-+ len--;
-+ }
-+ return count;
-+fail:
-+ return -1;
-+}
-+
-+#endif /* DWC_UTFLIB */
-+
-+
-+/* dwc_debug.h */
-+
-+dwc_bool_t DWC_IN_IRQ(void)
-+{
-+// return in_irq();
-+ return 0;
-+}
-+
-+dwc_bool_t DWC_IN_BH(void)
-+{
-+// return in_softirq();
-+ return 0;
-+}
-+
-+void DWC_VPRINTF(char *format, va_list args)
-+{
-+ vprintf(format, args);
-+}
-+
-+int DWC_VSNPRINTF(char *str, int size, char *format, va_list args)
-+{
-+ return vsnprintf(str, size, format, args);
-+}
-+
-+void DWC_PRINTF(char *format, ...)
-+{
-+ va_list args;
-+
-+ va_start(args, format);
-+ DWC_VPRINTF(format, args);
-+ va_end(args);
-+}
-+
-+int DWC_SPRINTF(char *buffer, char *format, ...)
-+{
-+ int retval;
-+ va_list args;
-+
-+ va_start(args, format);
-+ retval = vsprintf(buffer, format, args);
-+ va_end(args);
-+ return retval;
-+}
-+
-+int DWC_SNPRINTF(char *buffer, int size, char *format, ...)
-+{
-+ int retval;
-+ va_list args;
-+
-+ va_start(args, format);
-+ retval = vsnprintf(buffer, size, format, args);
-+ va_end(args);
-+ return retval;
-+}
-+
-+void __DWC_WARN(char *format, ...)
-+{
-+ va_list args;
-+
-+ va_start(args, format);
-+ DWC_VPRINTF(format, args);
-+ va_end(args);
-+}
-+
-+void __DWC_ERROR(char *format, ...)
-+{
-+ va_list args;
-+
-+ va_start(args, format);
-+ DWC_VPRINTF(format, args);
-+ va_end(args);
-+}
-+
-+void DWC_EXCEPTION(char *format, ...)
-+{
-+ va_list args;
-+
-+ va_start(args, format);
-+ DWC_VPRINTF(format, args);
-+ va_end(args);
-+// BUG_ON(1); ???
-+}
-+
-+#ifdef DEBUG
-+void __DWC_DEBUG(char *format, ...)
-+{
-+ va_list args;
-+
-+ va_start(args, format);
-+ DWC_VPRINTF(format, args);
-+ va_end(args);
-+}
-+#endif
-+
-+
-+/* dwc_mem.h */
-+
-+#if 0
-+dwc_pool_t *DWC_DMA_POOL_CREATE(uint32_t size,
-+ uint32_t align,
-+ uint32_t alloc)
-+{
-+ struct dma_pool *pool = dma_pool_create("Pool", NULL,
-+ size, align, alloc);
-+ return (dwc_pool_t *)pool;
-+}
-+
-+void DWC_DMA_POOL_DESTROY(dwc_pool_t *pool)
-+{
-+ dma_pool_destroy((struct dma_pool *)pool);
-+}
-+
-+void *DWC_DMA_POOL_ALLOC(dwc_pool_t *pool, uint64_t *dma_addr)
-+{
-+// return dma_pool_alloc((struct dma_pool *)pool, GFP_KERNEL, dma_addr);
-+ return dma_pool_alloc((struct dma_pool *)pool, M_WAITOK, dma_addr);
-+}
-+
-+void *DWC_DMA_POOL_ZALLOC(dwc_pool_t *pool, uint64_t *dma_addr)
-+{
-+ void *vaddr = DWC_DMA_POOL_ALLOC(pool, dma_addr);
-+ memset(..);
-+}
-+
-+void DWC_DMA_POOL_FREE(dwc_pool_t *pool, void *vaddr, void *daddr)
-+{
-+ dma_pool_free(pool, vaddr, daddr);
-+}
-+#endif
-+
-+static void dmamap_cb(void *arg, bus_dma_segment_t *segs, int nseg, int error)
-+{
-+ if (error)
-+ return;
-+ *(bus_addr_t *)arg = segs[0].ds_addr;
-+}
-+
-+void *__DWC_DMA_ALLOC(void *dma_ctx, uint32_t size, dwc_dma_t *dma_addr)
-+{
-+ dwc_dmactx_t *dma = (dwc_dmactx_t *)dma_ctx;
-+ int error;
-+
-+ error = bus_dma_tag_create(
-+#if __FreeBSD_version >= 700000
-+ bus_get_dma_tag(dma->dev), /* parent */
-+#else
-+ NULL, /* parent */
-+#endif
-+ 4, 0, /* alignment, bounds */
-+ BUS_SPACE_MAXADDR_32BIT, /* lowaddr */
-+ BUS_SPACE_MAXADDR, /* highaddr */
-+ NULL, NULL, /* filter, filterarg */
-+ size, /* maxsize */
-+ 1, /* nsegments */
-+ size, /* maxsegsize */
-+ 0, /* flags */
-+ NULL, /* lockfunc */
-+ NULL, /* lockarg */
-+ &dma->dma_tag);
-+ if (error) {
-+ device_printf(dma->dev, "%s: bus_dma_tag_create failed: %d\n",
-+ __func__, error);
-+ goto fail_0;
-+ }
-+
-+ error = bus_dmamem_alloc(dma->dma_tag, &dma->dma_vaddr,
-+ BUS_DMA_NOWAIT | BUS_DMA_COHERENT, &dma->dma_map);
-+ if (error) {
-+ device_printf(dma->dev, "%s: bus_dmamem_alloc(%ju) failed: %d\n",
-+ __func__, (uintmax_t)size, error);
-+ goto fail_1;
-+ }
-+
-+ dma->dma_paddr = 0;
-+ error = bus_dmamap_load(dma->dma_tag, dma->dma_map, dma->dma_vaddr, size,
-+ dmamap_cb, &dma->dma_paddr, BUS_DMA_NOWAIT);
-+ if (error || dma->dma_paddr == 0) {
-+ device_printf(dma->dev, "%s: bus_dmamap_load failed: %d\n",
-+ __func__, error);
-+ goto fail_2;
-+ }
-+
-+ *dma_addr = dma->dma_paddr;
-+ return dma->dma_vaddr;
-+
-+fail_2:
-+ bus_dmamap_unload(dma->dma_tag, dma->dma_map);
-+fail_1:
-+ bus_dmamem_free(dma->dma_tag, dma->dma_vaddr, dma->dma_map);
-+ bus_dma_tag_destroy(dma->dma_tag);
-+fail_0:
-+ dma->dma_map = NULL;
-+ dma->dma_tag = NULL;
-+
-+ return NULL;
-+}
-+
-+void __DWC_DMA_FREE(void *dma_ctx, uint32_t size, void *virt_addr, dwc_dma_t dma_addr)
-+{
-+ dwc_dmactx_t *dma = (dwc_dmactx_t *)dma_ctx;
-+
-+ if (dma->dma_tag == NULL)
-+ return;
-+ if (dma->dma_map != NULL) {
-+ bus_dmamap_sync(dma->dma_tag, dma->dma_map,
-+ BUS_DMASYNC_POSTREAD | BUS_DMASYNC_POSTWRITE);
-+ bus_dmamap_unload(dma->dma_tag, dma->dma_map);
-+ bus_dmamem_free(dma->dma_tag, dma->dma_vaddr, dma->dma_map);
-+ dma->dma_map = NULL;
-+ }
-+
-+ bus_dma_tag_destroy(dma->dma_tag);
-+ dma->dma_tag = NULL;
-+}
-+
-+void *__DWC_ALLOC(void *mem_ctx, uint32_t size)
-+{
-+ return malloc(size, M_DEVBUF, M_WAITOK | M_ZERO);
-+}
-+
-+void *__DWC_ALLOC_ATOMIC(void *mem_ctx, uint32_t size)
-+{
-+ return malloc(size, M_DEVBUF, M_NOWAIT | M_ZERO);
-+}
-+
-+void __DWC_FREE(void *mem_ctx, void *addr)
-+{
-+ free(addr, M_DEVBUF);
-+}
-+
-+
-+#ifdef DWC_CRYPTOLIB
-+/* dwc_crypto.h */
-+
-+void DWC_RANDOM_BYTES(uint8_t *buffer, uint32_t length)
-+{
-+ get_random_bytes(buffer, length);
-+}
-+
-+int DWC_AES_CBC(uint8_t *message, uint32_t messagelen, uint8_t *key, uint32_t keylen, uint8_t iv[16], uint8_t *out)
-+{
-+ struct crypto_blkcipher *tfm;
-+ struct blkcipher_desc desc;
-+ struct scatterlist sgd;
-+ struct scatterlist sgs;
-+
-+ tfm = crypto_alloc_blkcipher("cbc(aes)", 0, CRYPTO_ALG_ASYNC);
-+ if (tfm == NULL) {
-+ printk("failed to load transform for aes CBC\n");
-+ return -1;
-+ }
-+
-+ crypto_blkcipher_setkey(tfm, key, keylen);
-+ crypto_blkcipher_set_iv(tfm, iv, 16);
-+
-+ sg_init_one(&sgd, out, messagelen);
-+ sg_init_one(&sgs, message, messagelen);
-+
-+ desc.tfm = tfm;
-+ desc.flags = 0;
-+
-+ if (crypto_blkcipher_encrypt(&desc, &sgd, &sgs, messagelen)) {
-+ crypto_free_blkcipher(tfm);
-+ DWC_ERROR("AES CBC encryption failed");
-+ return -1;
-+ }
-+
-+ crypto_free_blkcipher(tfm);
-+ return 0;
-+}
-+
-+int DWC_SHA256(uint8_t *message, uint32_t len, uint8_t *out)
-+{
-+ struct crypto_hash *tfm;
-+ struct hash_desc desc;
-+ struct scatterlist sg;
-+
-+ tfm = crypto_alloc_hash("sha256", 0, CRYPTO_ALG_ASYNC);
-+ if (IS_ERR(tfm)) {
-+ DWC_ERROR("Failed to load transform for sha256: %ld", PTR_ERR(tfm));
-+ return 0;
-+ }
-+ desc.tfm = tfm;
-+ desc.flags = 0;
-+
-+ sg_init_one(&sg, message, len);
-+ crypto_hash_digest(&desc, &sg, len, out);
-+ crypto_free_hash(tfm);
-+
-+ return 1;
-+}
-+
-+int DWC_HMAC_SHA256(uint8_t *message, uint32_t messagelen,
-+ uint8_t *key, uint32_t keylen, uint8_t *out)
-+{
-+ struct crypto_hash *tfm;
-+ struct hash_desc desc;
-+ struct scatterlist sg;
-+
-+ tfm = crypto_alloc_hash("hmac(sha256)", 0, CRYPTO_ALG_ASYNC);
-+ if (IS_ERR(tfm)) {
-+ DWC_ERROR("Failed to load transform for hmac(sha256): %ld", PTR_ERR(tfm));
-+ return 0;
-+ }
-+ desc.tfm = tfm;
-+ desc.flags = 0;
-+
-+ sg_init_one(&sg, message, messagelen);
-+ crypto_hash_setkey(tfm, key, keylen);
-+ crypto_hash_digest(&desc, &sg, messagelen, out);
-+ crypto_free_hash(tfm);
-+
-+ return 1;
-+}
-+
-+#endif /* DWC_CRYPTOLIB */
-+
-+
-+/* Byte Ordering Conversions */
-+
-+uint32_t DWC_CPU_TO_LE32(uint32_t *p)
-+{
-+#ifdef __LITTLE_ENDIAN
-+ return *p;
-+#else
-+ uint8_t *u_p = (uint8_t *)p;
-+
-+ return (u_p[3] | (u_p[2] << 8) | (u_p[1] << 16) | (u_p[0] << 24));
-+#endif
-+}
-+
-+uint32_t DWC_CPU_TO_BE32(uint32_t *p)
-+{
-+#ifdef __BIG_ENDIAN
-+ return *p;
-+#else
-+ uint8_t *u_p = (uint8_t *)p;
-+
-+ return (u_p[3] | (u_p[2] << 8) | (u_p[1] << 16) | (u_p[0] << 24));
-+#endif
-+}
-+
-+uint32_t DWC_LE32_TO_CPU(uint32_t *p)
-+{
-+#ifdef __LITTLE_ENDIAN
-+ return *p;
-+#else
-+ uint8_t *u_p = (uint8_t *)p;
-+
-+ return (u_p[3] | (u_p[2] << 8) | (u_p[1] << 16) | (u_p[0] << 24));
-+#endif
-+}
-+
-+uint32_t DWC_BE32_TO_CPU(uint32_t *p)
-+{
-+#ifdef __BIG_ENDIAN
-+ return *p;
-+#else
-+ uint8_t *u_p = (uint8_t *)p;
-+
-+ return (u_p[3] | (u_p[2] << 8) | (u_p[1] << 16) | (u_p[0] << 24));
-+#endif
-+}
-+
-+uint16_t DWC_CPU_TO_LE16(uint16_t *p)
-+{
-+#ifdef __LITTLE_ENDIAN
-+ return *p;
-+#else
-+ uint8_t *u_p = (uint8_t *)p;
-+ return (u_p[1] | (u_p[0] << 8));
-+#endif
-+}
-+
-+uint16_t DWC_CPU_TO_BE16(uint16_t *p)
-+{
-+#ifdef __BIG_ENDIAN
-+ return *p;
-+#else
-+ uint8_t *u_p = (uint8_t *)p;
-+ return (u_p[1] | (u_p[0] << 8));
-+#endif
-+}
-+
-+uint16_t DWC_LE16_TO_CPU(uint16_t *p)
-+{
-+#ifdef __LITTLE_ENDIAN
-+ return *p;
-+#else
-+ uint8_t *u_p = (uint8_t *)p;
-+ return (u_p[1] | (u_p[0] << 8));
-+#endif
-+}
-+
-+uint16_t DWC_BE16_TO_CPU(uint16_t *p)
-+{
-+#ifdef __BIG_ENDIAN
-+ return *p;
-+#else
-+ uint8_t *u_p = (uint8_t *)p;
-+ return (u_p[1] | (u_p[0] << 8));
-+#endif
-+}
-+
-+
-+/* Registers */
-+
-+uint32_t DWC_READ_REG32(void *io_ctx, uint32_t volatile *reg)
-+{
-+ dwc_ioctx_t *io = (dwc_ioctx_t *)io_ctx;
-+ bus_size_t ior = (bus_size_t)reg;
-+
-+ return bus_space_read_4(io->iot, io->ioh, ior);
-+}
-+
-+#if 0
-+uint64_t DWC_READ_REG64(void *io_ctx, uint64_t volatile *reg)
-+{
-+ dwc_ioctx_t *io = (dwc_ioctx_t *)io_ctx;
-+ bus_size_t ior = (bus_size_t)reg;
-+
-+ return bus_space_read_8(io->iot, io->ioh, ior);
-+}
-+#endif
-+
-+void DWC_WRITE_REG32(void *io_ctx, uint32_t volatile *reg, uint32_t value)
-+{
-+ dwc_ioctx_t *io = (dwc_ioctx_t *)io_ctx;
-+ bus_size_t ior = (bus_size_t)reg;
-+
-+ bus_space_write_4(io->iot, io->ioh, ior, value);
-+}
-+
-+#if 0
-+void DWC_WRITE_REG64(void *io_ctx, uint64_t volatile *reg, uint64_t value)
-+{
-+ dwc_ioctx_t *io = (dwc_ioctx_t *)io_ctx;
-+ bus_size_t ior = (bus_size_t)reg;
-+
-+ bus_space_write_8(io->iot, io->ioh, ior, value);
-+}
-+#endif
-+
-+void DWC_MODIFY_REG32(void *io_ctx, uint32_t volatile *reg, uint32_t clear_mask,
-+ uint32_t set_mask)
-+{
-+ dwc_ioctx_t *io = (dwc_ioctx_t *)io_ctx;
-+ bus_size_t ior = (bus_size_t)reg;
-+
-+ bus_space_write_4(io->iot, io->ioh, ior,
-+ (bus_space_read_4(io->iot, io->ioh, ior) &
-+ ~clear_mask) | set_mask);
-+}
-+
-+#if 0
-+void DWC_MODIFY_REG64(void *io_ctx, uint64_t volatile *reg, uint64_t clear_mask,
-+ uint64_t set_mask)
-+{
-+ dwc_ioctx_t *io = (dwc_ioctx_t *)io_ctx;
-+ bus_size_t ior = (bus_size_t)reg;
-+
-+ bus_space_write_8(io->iot, io->ioh, ior,
-+ (bus_space_read_8(io->iot, io->ioh, ior) &
-+ ~clear_mask) | set_mask);
-+}
-+#endif
-+
-+
-+/* Locking */
-+
-+dwc_spinlock_t *DWC_SPINLOCK_ALLOC(void)
-+{
-+ struct mtx *sl = DWC_ALLOC(sizeof(*sl));
-+
-+ if (!sl) {
-+ DWC_ERROR("Cannot allocate memory for spinlock");
-+ return NULL;
-+ }
-+
-+ mtx_init(sl, "dw3spn", NULL, MTX_SPIN);
-+ return (dwc_spinlock_t *)sl;
-+}
-+
-+void DWC_SPINLOCK_FREE(dwc_spinlock_t *lock)
-+{
-+ struct mtx *sl = (struct mtx *)lock;
-+
-+ mtx_destroy(sl);
-+ DWC_FREE(sl);
-+}
-+
-+void DWC_SPINLOCK(dwc_spinlock_t *lock)
-+{
-+ mtx_lock_spin((struct mtx *)lock); // ???
-+}
-+
-+void DWC_SPINUNLOCK(dwc_spinlock_t *lock)
-+{
-+ mtx_unlock_spin((struct mtx *)lock); // ???
-+}
-+
-+void DWC_SPINLOCK_IRQSAVE(dwc_spinlock_t *lock, dwc_irqflags_t *flags)
-+{
-+ mtx_lock_spin((struct mtx *)lock);
-+}
-+
-+void DWC_SPINUNLOCK_IRQRESTORE(dwc_spinlock_t *lock, dwc_irqflags_t flags)
-+{
-+ mtx_unlock_spin((struct mtx *)lock);
-+}
-+
-+dwc_mutex_t *DWC_MUTEX_ALLOC(void)
-+{
-+ struct mtx *m;
-+ dwc_mutex_t *mutex = (dwc_mutex_t *)DWC_ALLOC(sizeof(struct mtx));
-+
-+ if (!mutex) {
-+ DWC_ERROR("Cannot allocate memory for mutex");
-+ return NULL;
-+ }
-+
-+ m = (struct mtx *)mutex;
-+ mtx_init(m, "dw3mtx", NULL, MTX_DEF);
-+ return mutex;
-+}
-+
-+#if (defined(DWC_LINUX) && defined(CONFIG_DEBUG_MUTEXES))
-+#else
-+void DWC_MUTEX_FREE(dwc_mutex_t *mutex)
-+{
-+ mtx_destroy((struct mtx *)mutex);
-+ DWC_FREE(mutex);
-+}
-+#endif
-+
-+void DWC_MUTEX_LOCK(dwc_mutex_t *mutex)
-+{
-+ struct mtx *m = (struct mtx *)mutex;
-+
-+ mtx_lock(m);
-+}
-+
-+int DWC_MUTEX_TRYLOCK(dwc_mutex_t *mutex)
-+{
-+ struct mtx *m = (struct mtx *)mutex;
-+
-+ return mtx_trylock(m);
-+}
-+
-+void DWC_MUTEX_UNLOCK(dwc_mutex_t *mutex)
-+{
-+ struct mtx *m = (struct mtx *)mutex;
-+
-+ mtx_unlock(m);
-+}
-+
-+
-+/* Timing */
-+
-+void DWC_UDELAY(uint32_t usecs)
-+{
-+ DELAY(usecs);
-+}
-+
-+void DWC_MDELAY(uint32_t msecs)
-+{
-+ do {
-+ DELAY(1000);
-+ } while (--msecs);
-+}
-+
-+void DWC_MSLEEP(uint32_t msecs)
-+{
-+ struct timeval tv;
-+
-+ tv.tv_sec = msecs / 1000;
-+ tv.tv_usec = (msecs - tv.tv_sec * 1000) * 1000;
-+ pause("dw3slp", tvtohz(&tv));
-+}
-+
-+uint32_t DWC_TIME(void)
-+{
-+ struct timeval tv;
-+
-+ microuptime(&tv); // or getmicrouptime? (less precise, but faster)
-+ return tv.tv_sec * 1000 + tv.tv_usec / 1000;
-+}
-+
-+
-+/* Timers */
-+
-+struct dwc_timer {
-+ struct callout t;
-+ char *name;
-+ dwc_spinlock_t *lock;
-+ dwc_timer_callback_t cb;
-+ void *data;
-+};
-+
-+dwc_timer_t *DWC_TIMER_ALLOC(char *name, dwc_timer_callback_t cb, void *data)
-+{
-+ dwc_timer_t *t = DWC_ALLOC(sizeof(*t));
-+
-+ if (!t) {
-+ DWC_ERROR("Cannot allocate memory for timer");
-+ return NULL;
-+ }
-+
-+ callout_init(&t->t, 1);
-+
-+ t->name = DWC_STRDUP(name);
-+ if (!t->name) {
-+ DWC_ERROR("Cannot allocate memory for timer->name");
-+ goto no_name;
-+ }
-+
-+ t->lock = DWC_SPINLOCK_ALLOC();
-+ if (!t->lock) {
-+ DWC_ERROR("Cannot allocate memory for lock");
-+ goto no_lock;
-+ }
-+
-+ t->cb = cb;
-+ t->data = data;
-+
-+ return t;
-+
-+ no_lock:
-+ DWC_FREE(t->name);
-+ no_name:
-+ DWC_FREE(t);
-+
-+ return NULL;
-+}
-+
-+void DWC_TIMER_FREE(dwc_timer_t *timer)
-+{
-+ callout_stop(&timer->t);
-+ DWC_SPINLOCK_FREE(timer->lock);
-+ DWC_FREE(timer->name);
-+ DWC_FREE(timer);
-+}
-+
-+void DWC_TIMER_SCHEDULE(dwc_timer_t *timer, uint32_t time)
-+{
-+ struct timeval tv;
-+
-+ tv.tv_sec = time / 1000;
-+ tv.tv_usec = (time - tv.tv_sec * 1000) * 1000;
-+ callout_reset(&timer->t, tvtohz(&tv), timer->cb, timer->data);
-+}
-+
-+void DWC_TIMER_CANCEL(dwc_timer_t *timer)
-+{
-+ callout_stop(&timer->t);
-+}
-+
-+
-+/* Wait Queues */
-+
-+struct dwc_waitq {
-+ struct mtx lock;
-+ int abort;
-+};
-+
-+dwc_waitq_t *DWC_WAITQ_ALLOC(void)
-+{
-+ dwc_waitq_t *wq = DWC_ALLOC(sizeof(*wq));
-+
-+ if (!wq) {
-+ DWC_ERROR("Cannot allocate memory for waitqueue");
-+ return NULL;
-+ }
-+
-+ mtx_init(&wq->lock, "dw3wtq", NULL, MTX_DEF);
-+ wq->abort = 0;
-+
-+ return wq;
-+}
-+
-+void DWC_WAITQ_FREE(dwc_waitq_t *wq)
-+{
-+ mtx_destroy(&wq->lock);
-+ DWC_FREE(wq);
-+}
-+
-+int32_t DWC_WAITQ_WAIT(dwc_waitq_t *wq, dwc_waitq_condition_t cond, void *data)
-+{
-+// intrmask_t ipl;
-+ int result = 0;
-+
-+ mtx_lock(&wq->lock);
-+// ipl = splbio();
-+
-+ /* Skip the sleep if already aborted or triggered */
-+ if (!wq->abort && !cond(data)) {
-+// splx(ipl);
-+ result = msleep(wq, &wq->lock, PCATCH, "dw3wat", 0); // infinite timeout
-+// ipl = splbio();
-+ }
-+
-+ if (result == ERESTART) { // signaled - restart
-+ result = -DWC_E_RESTART;
-+
-+ } else if (result == EINTR) { // signaled - interrupt
-+ result = -DWC_E_ABORT;
-+
-+ } else if (wq->abort) {
-+ result = -DWC_E_ABORT;
-+
-+ } else {
-+ result = 0;
-+ }
-+
-+ wq->abort = 0;
-+// splx(ipl);
-+ mtx_unlock(&wq->lock);
-+ return result;
-+}
-+
-+int32_t DWC_WAITQ_WAIT_TIMEOUT(dwc_waitq_t *wq, dwc_waitq_condition_t cond,
-+ void *data, int32_t msecs)
-+{
-+ struct timeval tv, tv1, tv2;
-+// intrmask_t ipl;
-+ int result = 0;
-+
-+ tv.tv_sec = msecs / 1000;
-+ tv.tv_usec = (msecs - tv.tv_sec * 1000) * 1000;
-+
-+ mtx_lock(&wq->lock);
-+// ipl = splbio();
-+
-+ /* Skip the sleep if already aborted or triggered */
-+ if (!wq->abort && !cond(data)) {
-+// splx(ipl);
-+ getmicrouptime(&tv1);
-+ result = msleep(wq, &wq->lock, PCATCH, "dw3wto", tvtohz(&tv));
-+ getmicrouptime(&tv2);
-+// ipl = splbio();
-+ }
-+
-+ if (result == 0) { // awoken
-+ if (wq->abort) {
-+ result = -DWC_E_ABORT;
-+ } else {
-+ tv2.tv_usec -= tv1.tv_usec;
-+ if (tv2.tv_usec < 0) {
-+ tv2.tv_usec += 1000000;
-+ tv2.tv_sec--;
-+ }
-+
-+ tv2.tv_sec -= tv1.tv_sec;
-+ result = tv2.tv_sec * 1000 + tv2.tv_usec / 1000;
-+ result = msecs - result;
-+ if (result <= 0)
-+ result = 1;
-+ }
-+ } else if (result == ERESTART) { // signaled - restart
-+ result = -DWC_E_RESTART;
-+
-+ } else if (result == EINTR) { // signaled - interrupt
-+ result = -DWC_E_ABORT;
-+
-+ } else { // timed out
-+ result = -DWC_E_TIMEOUT;
-+ }
-+
-+ wq->abort = 0;
-+// splx(ipl);
-+ mtx_unlock(&wq->lock);
-+ return result;
-+}
-+
-+void DWC_WAITQ_TRIGGER(dwc_waitq_t *wq)
-+{
-+ wakeup(wq);
-+}
-+
-+void DWC_WAITQ_ABORT(dwc_waitq_t *wq)
-+{
-+// intrmask_t ipl;
-+
-+ mtx_lock(&wq->lock);
-+// ipl = splbio();
-+ wq->abort = 1;
-+ wakeup(wq);
-+// splx(ipl);
-+ mtx_unlock(&wq->lock);
-+}
-+
-+
-+/* Threading */
-+
-+struct dwc_thread {
-+ struct proc *proc;
-+ int abort;
-+};
-+
-+dwc_thread_t *DWC_THREAD_RUN(dwc_thread_function_t func, char *name, void *data)
-+{
-+ int retval;
-+ dwc_thread_t *thread = DWC_ALLOC(sizeof(*thread));
-+
-+ if (!thread) {
-+ return NULL;
-+ }
-+
-+ thread->abort = 0;
-+ retval = kthread_create((void (*)(void *))func, data, &thread->proc,
-+ RFPROC | RFNOWAIT, 0, "%s", name);
-+ if (retval) {
-+ DWC_FREE(thread);
-+ return NULL;
-+ }
-+
-+ return thread;
-+}
-+
-+int DWC_THREAD_STOP(dwc_thread_t *thread)
-+{
-+ int retval;
-+
-+ thread->abort = 1;
-+ retval = tsleep(&thread->abort, 0, "dw3stp", 60 * hz);
-+
-+ if (retval == 0) {
-+ /* DWC_THREAD_EXIT() will free the thread struct */
-+ return 0;
-+ }
-+
-+ /* NOTE: We leak the thread struct if thread doesn't die */
-+
-+ if (retval == EWOULDBLOCK) {
-+ return -DWC_E_TIMEOUT;
-+ }
-+
-+ return -DWC_E_UNKNOWN;
-+}
-+
-+dwc_bool_t DWC_THREAD_SHOULD_STOP(dwc_thread_t *thread)
-+{
-+ return thread->abort;
-+}
-+
-+void DWC_THREAD_EXIT(dwc_thread_t *thread)
-+{
-+ wakeup(&thread->abort);
-+ DWC_FREE(thread);
-+ kthread_exit(0);
-+}
-+
-+
-+/* tasklets
-+ - Runs in interrupt context (cannot sleep)
-+ - Each tasklet runs on a single CPU [ How can we ensure this on FreeBSD? Does it matter? ]
-+ - Different tasklets can be running simultaneously on different CPUs [ shouldn't matter ]
-+ */
-+struct dwc_tasklet {
-+ struct task t;
-+ dwc_tasklet_callback_t cb;
-+ void *data;
-+};
-+
-+static void tasklet_callback(void *data, int pending) // what to do with pending ???
-+{
-+ dwc_tasklet_t *task = (dwc_tasklet_t *)data;
-+
-+ task->cb(task->data);
-+}
-+
-+dwc_tasklet_t *DWC_TASK_ALLOC(char *name, dwc_tasklet_callback_t cb, void *data)
-+{
-+ dwc_tasklet_t *task = DWC_ALLOC(sizeof(*task));
-+
-+ if (task) {
-+ task->cb = cb;
-+ task->data = data;
-+ TASK_INIT(&task->t, 0, tasklet_callback, task);
-+ } else {
-+ DWC_ERROR("Cannot allocate memory for tasklet");
-+ }
-+
-+ return task;
-+}
-+
-+void DWC_TASK_FREE(dwc_tasklet_t *task)
-+{
-+ taskqueue_drain(taskqueue_fast, &task->t); // ???
-+ DWC_FREE(task);
-+}
-+
-+void DWC_TASK_SCHEDULE(dwc_tasklet_t *task)
-+{
-+ /* Uses predefined system queue */
-+ taskqueue_enqueue_fast(taskqueue_fast, &task->t);
-+}
-+
-+
-+/* workqueues
-+ - Runs in process context (can sleep)
-+ */
-+typedef struct work_container {
-+ dwc_work_callback_t cb;
-+ void *data;
-+ dwc_workq_t *wq;
-+ char *name;
-+ int hz;
-+
-+#ifdef DEBUG
-+ DWC_CIRCLEQ_ENTRY(work_container) entry;
-+#endif
-+ struct task task;
-+} work_container_t;
-+
-+#ifdef DEBUG
-+DWC_CIRCLEQ_HEAD(work_container_queue, work_container);
-+#endif
-+
-+struct dwc_workq {
-+ struct taskqueue *taskq;
-+ dwc_spinlock_t *lock;
-+ dwc_waitq_t *waitq;
-+ int pending;
-+
-+#ifdef DEBUG
-+ struct work_container_queue entries;
-+#endif
-+};
-+
-+static void do_work(void *data, int pending) // what to do with pending ???
-+{
-+ work_container_t *container = (work_container_t *)data;
-+ dwc_workq_t *wq = container->wq;
-+ dwc_irqflags_t flags;
-+
-+ if (container->hz) {
-+ pause("dw3wrk", container->hz);
-+ }
-+
-+ container->cb(container->data);
-+ DWC_DEBUG("Work done: %s, container=%p", container->name, container);
-+
-+ DWC_SPINLOCK_IRQSAVE(wq->lock, &flags);
-+
-+#ifdef DEBUG
-+ DWC_CIRCLEQ_REMOVE(&wq->entries, container, entry);
-+#endif
-+ if (container->name)
-+ DWC_FREE(container->name);
-+ DWC_FREE(container);
-+ wq->pending--;
-+ DWC_SPINUNLOCK_IRQRESTORE(wq->lock, flags);
-+ DWC_WAITQ_TRIGGER(wq->waitq);
-+}
-+
-+static int work_done(void *data)
-+{
-+ dwc_workq_t *workq = (dwc_workq_t *)data;
-+
-+ return workq->pending == 0;
-+}
-+
-+int DWC_WORKQ_WAIT_WORK_DONE(dwc_workq_t *workq, int timeout)
-+{
-+ return DWC_WAITQ_WAIT_TIMEOUT(workq->waitq, work_done, workq, timeout);
-+}
-+
-+dwc_workq_t *DWC_WORKQ_ALLOC(char *name)
-+{
-+ dwc_workq_t *wq = DWC_ALLOC(sizeof(*wq));
-+
-+ if (!wq) {
-+ DWC_ERROR("Cannot allocate memory for workqueue");
-+ return NULL;
-+ }
-+
-+ wq->taskq = taskqueue_create(name, M_NOWAIT, taskqueue_thread_enqueue, &wq->taskq);
-+ if (!wq->taskq) {
-+ DWC_ERROR("Cannot allocate memory for taskqueue");
-+ goto no_taskq;
-+ }
-+
-+ wq->pending = 0;
-+
-+ wq->lock = DWC_SPINLOCK_ALLOC();
-+ if (!wq->lock) {
-+ DWC_ERROR("Cannot allocate memory for spinlock");
-+ goto no_lock;
-+ }
-+
-+ wq->waitq = DWC_WAITQ_ALLOC();
-+ if (!wq->waitq) {
-+ DWC_ERROR("Cannot allocate memory for waitqueue");
-+ goto no_waitq;
-+ }
-+
-+ taskqueue_start_threads(&wq->taskq, 1, PWAIT, "%s taskq", "dw3tsk");
-+
-+#ifdef DEBUG
-+ DWC_CIRCLEQ_INIT(&wq->entries);
-+#endif
-+ return wq;
-+
-+ no_waitq:
-+ DWC_SPINLOCK_FREE(wq->lock);
-+ no_lock:
-+ taskqueue_free(wq->taskq);
-+ no_taskq:
-+ DWC_FREE(wq);
-+
-+ return NULL;
-+}
-+
-+void DWC_WORKQ_FREE(dwc_workq_t *wq)
-+{
-+#ifdef DEBUG
-+ dwc_irqflags_t flags;
-+
-+ DWC_SPINLOCK_IRQSAVE(wq->lock, &flags);
-+
-+ if (wq->pending != 0) {
-+ struct work_container *container;
-+
-+ DWC_ERROR("Destroying work queue with pending work");
-+
-+ DWC_CIRCLEQ_FOREACH(container, &wq->entries, entry) {
-+ DWC_ERROR("Work %s still pending", container->name);
-+ }
-+ }
-+
-+ DWC_SPINUNLOCK_IRQRESTORE(wq->lock, flags);
-+#endif
-+ DWC_WAITQ_FREE(wq->waitq);
-+ DWC_SPINLOCK_FREE(wq->lock);
-+ taskqueue_free(wq->taskq);
-+ DWC_FREE(wq);
-+}
-+
-+void DWC_WORKQ_SCHEDULE(dwc_workq_t *wq, dwc_work_callback_t cb, void *data,
-+ char *format, ...)
-+{
-+ dwc_irqflags_t flags;
-+ work_container_t *container;
-+ static char name[128];
-+ va_list args;
-+
-+ va_start(args, format);
-+ DWC_VSNPRINTF(name, 128, format, args);
-+ va_end(args);
-+
-+ DWC_SPINLOCK_IRQSAVE(wq->lock, &flags);
-+ wq->pending++;
-+ DWC_SPINUNLOCK_IRQRESTORE(wq->lock, flags);
-+ DWC_WAITQ_TRIGGER(wq->waitq);
-+
-+ container = DWC_ALLOC_ATOMIC(sizeof(*container));
-+ if (!container) {
-+ DWC_ERROR("Cannot allocate memory for container");
-+ return;
-+ }
-+
-+ container->name = DWC_STRDUP(name);
-+ if (!container->name) {
-+ DWC_ERROR("Cannot allocate memory for container->name");
-+ DWC_FREE(container);
-+ return;
-+ }
-+
-+ container->cb = cb;
-+ container->data = data;
-+ container->wq = wq;
-+ container->hz = 0;
-+
-+ DWC_DEBUG("Queueing work: %s, container=%p", container->name, container);
-+
-+ TASK_INIT(&container->task, 0, do_work, container);
-+
-+#ifdef DEBUG
-+ DWC_CIRCLEQ_INSERT_TAIL(&wq->entries, container, entry);
-+#endif
-+ taskqueue_enqueue_fast(wq->taskq, &container->task);
-+}
-+
-+void DWC_WORKQ_SCHEDULE_DELAYED(dwc_workq_t *wq, dwc_work_callback_t cb,
-+ void *data, uint32_t time, char *format, ...)
-+{
-+ dwc_irqflags_t flags;
-+ work_container_t *container;
-+ static char name[128];
-+ struct timeval tv;
-+ va_list args;
-+
-+ va_start(args, format);
-+ DWC_VSNPRINTF(name, 128, format, args);
-+ va_end(args);
-+
-+ DWC_SPINLOCK_IRQSAVE(wq->lock, &flags);
-+ wq->pending++;
-+ DWC_SPINUNLOCK_IRQRESTORE(wq->lock, flags);
-+ DWC_WAITQ_TRIGGER(wq->waitq);
-+
-+ container = DWC_ALLOC_ATOMIC(sizeof(*container));
-+ if (!container) {
-+ DWC_ERROR("Cannot allocate memory for container");
-+ return;
-+ }
-+
-+ container->name = DWC_STRDUP(name);
-+ if (!container->name) {
-+ DWC_ERROR("Cannot allocate memory for container->name");
-+ DWC_FREE(container);
-+ return;
-+ }
-+
-+ container->cb = cb;
-+ container->data = data;
-+ container->wq = wq;
-+
-+ tv.tv_sec = time / 1000;
-+ tv.tv_usec = (time - tv.tv_sec * 1000) * 1000;
-+ container->hz = tvtohz(&tv);
-+
-+ DWC_DEBUG("Queueing work: %s, container=%p", container->name, container);
-+
-+ TASK_INIT(&container->task, 0, do_work, container);
-+
-+#ifdef DEBUG
-+ DWC_CIRCLEQ_INSERT_TAIL(&wq->entries, container, entry);
-+#endif
-+ taskqueue_enqueue_fast(wq->taskq, &container->task);
-+}
-+
-+int DWC_WORKQ_PENDING(dwc_workq_t *wq)
-+{
-+ return wq->pending;
-+}
---- /dev/null
-+++ b/drivers/usb/host/dwc_common_port/dwc_common_linux.c
-@@ -0,0 +1,1433 @@
-+#include <linux/kernel.h>
-+#include <linux/init.h>
-+#include <linux/module.h>
-+#include <linux/kthread.h>
-+
-+#ifdef DWC_CCLIB
-+# include "dwc_cc.h"
-+#endif
-+
-+#ifdef DWC_CRYPTOLIB
-+# include "dwc_modpow.h"
-+# include "dwc_dh.h"
-+# include "dwc_crypto.h"
-+#endif
-+
-+#ifdef DWC_NOTIFYLIB
-+# include "dwc_notifier.h"
-+#endif
-+
-+/* OS-Level Implementations */
-+
-+/* This is the Linux kernel implementation of the DWC platform library. */
-+#include <linux/moduleparam.h>
-+#include <linux/ctype.h>
-+#include <linux/crypto.h>
-+#include <linux/delay.h>
-+#include <linux/device.h>
-+#include <linux/dma-mapping.h>
-+#include <linux/cdev.h>
-+#include <linux/errno.h>
-+#include <linux/interrupt.h>
-+#include <linux/jiffies.h>
-+#include <linux/list.h>
-+#include <linux/pci.h>
-+#include <linux/random.h>
-+#include <linux/scatterlist.h>
-+#include <linux/slab.h>
-+#include <linux/stat.h>
-+#include <linux/string.h>
-+#include <linux/timer.h>
-+#include <linux/usb.h>
-+
-+#include <linux/version.h>
-+
-+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,24)
-+# include <linux/usb/gadget.h>
-+#else
-+# include <linux/usb_gadget.h>
-+#endif
-+
-+#include <asm/io.h>
-+#include <asm/page.h>
-+#include <asm/uaccess.h>
-+#include <asm/unaligned.h>
-+
-+#include "dwc_os.h"
-+#include "dwc_list.h"
-+
-+
-+/* MISC */
-+
-+void *DWC_MEMSET(void *dest, uint8_t byte, uint32_t size)
-+{
-+ return memset(dest, byte, size);
-+}
-+
-+void *DWC_MEMCPY(void *dest, void const *src, uint32_t size)
-+{
-+ return memcpy(dest, src, size);
-+}
-+
-+void *DWC_MEMMOVE(void *dest, void *src, uint32_t size)
-+{
-+ return memmove(dest, src, size);
-+}
-+
-+int DWC_MEMCMP(void *m1, void *m2, uint32_t size)
-+{
-+ return memcmp(m1, m2, size);
-+}
-+
-+int DWC_STRNCMP(void *s1, void *s2, uint32_t size)
-+{
-+ return strncmp(s1, s2, size);
-+}
-+
-+int DWC_STRCMP(void *s1, void *s2)
-+{
-+ return strcmp(s1, s2);
-+}
-+
-+int DWC_STRLEN(char const *str)
-+{
-+ return strlen(str);
-+}
-+
-+char *DWC_STRCPY(char *to, char const *from)
-+{
-+ return strcpy(to, from);
-+}
-+
-+char *DWC_STRDUP(char const *str)
-+{
-+ int len = DWC_STRLEN(str) + 1;
-+ char *new = DWC_ALLOC_ATOMIC(len);
-+
-+ if (!new) {
-+ return NULL;
-+ }
-+
-+ DWC_MEMCPY(new, str, len);
-+ return new;
-+}
-+
-+int DWC_ATOI(const char *str, int32_t *value)
-+{
-+ char *end = NULL;
-+
-+ *value = simple_strtol(str, &end, 0);
-+ if (*end == '\0') {
-+ return 0;
-+ }
-+
-+ return -1;
-+}
-+
-+int DWC_ATOUI(const char *str, uint32_t *value)
-+{
-+ char *end = NULL;
-+
-+ *value = simple_strtoul(str, &end, 0);
-+ if (*end == '\0') {
-+ return 0;
-+ }
-+
-+ return -1;
-+}
-+
-+
-+#ifdef DWC_UTFLIB
-+/* From usbstring.c */
-+
-+int DWC_UTF8_TO_UTF16LE(uint8_t const *s, uint16_t *cp, unsigned len)
-+{
-+ int count = 0;
-+ u8 c;
-+ u16 uchar;
-+
-+ /* this insists on correct encodings, though not minimal ones.
-+ * BUT it currently rejects legit 4-byte UTF-8 code points,
-+ * which need surrogate pairs. (Unicode 3.1 can use them.)
-+ */
-+ while (len != 0 && (c = (u8) *s++) != 0) {
-+ if (unlikely(c & 0x80)) {
-+ // 2-byte sequence:
-+ // 00000yyyyyxxxxxx = 110yyyyy 10xxxxxx
-+ if ((c & 0xe0) == 0xc0) {
-+ uchar = (c & 0x1f) << 6;
-+
-+ c = (u8) *s++;
-+ if ((c & 0xc0) != 0xc0)
-+ goto fail;
-+ c &= 0x3f;
-+ uchar |= c;
-+
-+ // 3-byte sequence (most CJKV characters):
-+ // zzzzyyyyyyxxxxxx = 1110zzzz 10yyyyyy 10xxxxxx
-+ } else if ((c & 0xf0) == 0xe0) {
-+ uchar = (c & 0x0f) << 12;
-+
-+ c = (u8) *s++;
-+ if ((c & 0xc0) != 0xc0)
-+ goto fail;
-+ c &= 0x3f;
-+ uchar |= c << 6;
-+
-+ c = (u8) *s++;
-+ if ((c & 0xc0) != 0xc0)
-+ goto fail;
-+ c &= 0x3f;
-+ uchar |= c;
-+
-+ /* no bogus surrogates */
-+ if (0xd800 <= uchar && uchar <= 0xdfff)
-+ goto fail;
-+
-+ // 4-byte sequence (surrogate pairs, currently rare):
-+ // 11101110wwwwzzzzyy + 110111yyyyxxxxxx
-+ // = 11110uuu 10uuzzzz 10yyyyyy 10xxxxxx
-+ // (uuuuu = wwww + 1)
-+ // FIXME accept the surrogate code points (only)
-+ } else
-+ goto fail;
-+ } else
-+ uchar = c;
-+ put_unaligned (cpu_to_le16 (uchar), cp++);
-+ count++;
-+ len--;
-+ }
-+ return count;
-+fail:
-+ return -1;
-+}
-+#endif /* DWC_UTFLIB */
-+
-+
-+/* dwc_debug.h */
-+
-+dwc_bool_t DWC_IN_IRQ(void)
-+{
-+ return in_irq();
-+}
-+
-+dwc_bool_t DWC_IN_BH(void)
-+{
-+ return in_softirq();
-+}
-+
-+void DWC_VPRINTF(char *format, va_list args)
-+{
-+ vprintk(format, args);
-+}
-+
-+int DWC_VSNPRINTF(char *str, int size, char *format, va_list args)
-+{
-+ return vsnprintf(str, size, format, args);
-+}
-+
-+void DWC_PRINTF(char *format, ...)
-+{
-+ va_list args;
-+
-+ va_start(args, format);
-+ DWC_VPRINTF(format, args);
-+ va_end(args);
-+}
-+
-+int DWC_SPRINTF(char *buffer, char *format, ...)
-+{
-+ int retval;
-+ va_list args;
-+
-+ va_start(args, format);
-+ retval = vsprintf(buffer, format, args);
-+ va_end(args);
-+ return retval;
-+}
-+
-+int DWC_SNPRINTF(char *buffer, int size, char *format, ...)
-+{
-+ int retval;
-+ va_list args;
-+
-+ va_start(args, format);
-+ retval = vsnprintf(buffer, size, format, args);
-+ va_end(args);
-+ return retval;
-+}
-+
-+void __DWC_WARN(char *format, ...)
-+{
-+ va_list args;
-+
-+ va_start(args, format);
-+ DWC_PRINTF(KERN_WARNING);
-+ DWC_VPRINTF(format, args);
-+ va_end(args);
-+}
-+
-+void __DWC_ERROR(char *format, ...)
-+{
-+ va_list args;
-+
-+ va_start(args, format);
-+ DWC_PRINTF(KERN_ERR);
-+ DWC_VPRINTF(format, args);
-+ va_end(args);
-+}
-+
-+void DWC_EXCEPTION(char *format, ...)
-+{
-+ va_list args;
-+
-+ va_start(args, format);
-+ DWC_PRINTF(KERN_ERR);
-+ DWC_VPRINTF(format, args);
-+ va_end(args);
-+ BUG_ON(1);
-+}
-+
-+#ifdef DEBUG
-+void __DWC_DEBUG(char *format, ...)
-+{
-+ va_list args;
-+
-+ va_start(args, format);
-+ DWC_PRINTF(KERN_DEBUG);
-+ DWC_VPRINTF(format, args);
-+ va_end(args);
-+}
-+#endif
-+
-+
-+/* dwc_mem.h */
-+
-+#if 0
-+dwc_pool_t *DWC_DMA_POOL_CREATE(uint32_t size,
-+ uint32_t align,
-+ uint32_t alloc)
-+{
-+ struct dma_pool *pool = dma_pool_create("Pool", NULL,
-+ size, align, alloc);
-+ return (dwc_pool_t *)pool;
-+}
-+
-+void DWC_DMA_POOL_DESTROY(dwc_pool_t *pool)
-+{
-+ dma_pool_destroy((struct dma_pool *)pool);
-+}
-+
-+void *DWC_DMA_POOL_ALLOC(dwc_pool_t *pool, uint64_t *dma_addr)
-+{
-+ return dma_pool_alloc((struct dma_pool *)pool, GFP_KERNEL, dma_addr);
-+}
-+
-+void *DWC_DMA_POOL_ZALLOC(dwc_pool_t *pool, uint64_t *dma_addr)
-+{
-+ void *vaddr = DWC_DMA_POOL_ALLOC(pool, dma_addr);
-+ memset(..);
-+}
-+
-+void DWC_DMA_POOL_FREE(dwc_pool_t *pool, void *vaddr, void *daddr)
-+{
-+ dma_pool_free(pool, vaddr, daddr);
-+}
-+#endif
-+
-+void *__DWC_DMA_ALLOC(void *dma_ctx, uint32_t size, dwc_dma_t *dma_addr)
-+{
-+#ifdef xxCOSIM /* Only works for 32-bit cosim */
-+ void *buf = dma_alloc_coherent(dma_ctx, (size_t)size, dma_addr, GFP_KERNEL);
-+#else
-+ void *buf = dma_alloc_coherent(dma_ctx, (size_t)size, dma_addr, GFP_KERNEL | GFP_DMA32);
-+#endif
-+ if (!buf) {
-+ return NULL;
-+ }
-+
-+ memset(buf, 0, (size_t)size);
-+ return buf;
-+}
-+
-+void *__DWC_DMA_ALLOC_ATOMIC(void *dma_ctx, uint32_t size, dwc_dma_t *dma_addr)
-+{
-+ void *buf = dma_alloc_coherent(NULL, (size_t)size, dma_addr, GFP_ATOMIC);
-+ if (!buf) {
-+ return NULL;
-+ }
-+ memset(buf, 0, (size_t)size);
-+ return buf;
-+}
-+
-+void __DWC_DMA_FREE(void *dma_ctx, uint32_t size, void *virt_addr, dwc_dma_t dma_addr)
-+{
-+ dma_free_coherent(dma_ctx, size, virt_addr, dma_addr);
-+}
-+
-+void *__DWC_ALLOC(void *mem_ctx, uint32_t size)
-+{
-+ return kzalloc(size, GFP_KERNEL);
-+}
-+
-+void *__DWC_ALLOC_ATOMIC(void *mem_ctx, uint32_t size)
-+{
-+ return kzalloc(size, GFP_ATOMIC);
-+}
-+
-+void __DWC_FREE(void *mem_ctx, void *addr)
-+{
-+ kfree(addr);
-+}
-+
-+
-+#ifdef DWC_CRYPTOLIB
-+/* dwc_crypto.h */
-+
-+void DWC_RANDOM_BYTES(uint8_t *buffer, uint32_t length)
-+{
-+ get_random_bytes(buffer, length);
-+}
-+
-+int DWC_AES_CBC(uint8_t *message, uint32_t messagelen, uint8_t *key, uint32_t keylen, uint8_t iv[16], uint8_t *out)
-+{
-+ struct crypto_blkcipher *tfm;
-+ struct blkcipher_desc desc;
-+ struct scatterlist sgd;
-+ struct scatterlist sgs;
-+
-+ tfm = crypto_alloc_blkcipher("cbc(aes)", 0, CRYPTO_ALG_ASYNC);
-+ if (tfm == NULL) {
-+ printk("failed to load transform for aes CBC\n");
-+ return -1;
-+ }
-+
-+ crypto_blkcipher_setkey(tfm, key, keylen);
-+ crypto_blkcipher_set_iv(tfm, iv, 16);
-+
-+ sg_init_one(&sgd, out, messagelen);
-+ sg_init_one(&sgs, message, messagelen);
-+
-+ desc.tfm = tfm;
-+ desc.flags = 0;
-+
-+ if (crypto_blkcipher_encrypt(&desc, &sgd, &sgs, messagelen)) {
-+ crypto_free_blkcipher(tfm);
-+ DWC_ERROR("AES CBC encryption failed");
-+ return -1;
-+ }
-+
-+ crypto_free_blkcipher(tfm);
-+ return 0;
-+}
-+
-+int DWC_SHA256(uint8_t *message, uint32_t len, uint8_t *out)
-+{
-+ struct crypto_hash *tfm;
-+ struct hash_desc desc;
-+ struct scatterlist sg;
-+
-+ tfm = crypto_alloc_hash("sha256", 0, CRYPTO_ALG_ASYNC);
-+ if (IS_ERR(tfm)) {
-+ DWC_ERROR("Failed to load transform for sha256: %ld\n", PTR_ERR(tfm));
-+ return 0;
-+ }
-+ desc.tfm = tfm;
-+ desc.flags = 0;
-+
-+ sg_init_one(&sg, message, len);
-+ crypto_hash_digest(&desc, &sg, len, out);
-+ crypto_free_hash(tfm);
-+
-+ return 1;
-+}
-+
-+int DWC_HMAC_SHA256(uint8_t *message, uint32_t messagelen,
-+ uint8_t *key, uint32_t keylen, uint8_t *out)
-+{
-+ struct crypto_hash *tfm;
-+ struct hash_desc desc;
-+ struct scatterlist sg;
-+
-+ tfm = crypto_alloc_hash("hmac(sha256)", 0, CRYPTO_ALG_ASYNC);
-+ if (IS_ERR(tfm)) {
-+ DWC_ERROR("Failed to load transform for hmac(sha256): %ld\n", PTR_ERR(tfm));
-+ return 0;
-+ }
-+ desc.tfm = tfm;
-+ desc.flags = 0;
-+
-+ sg_init_one(&sg, message, messagelen);
-+ crypto_hash_setkey(tfm, key, keylen);
-+ crypto_hash_digest(&desc, &sg, messagelen, out);
-+ crypto_free_hash(tfm);
-+
-+ return 1;
-+}
-+#endif /* DWC_CRYPTOLIB */
-+
-+
-+/* Byte Ordering Conversions */
-+
-+uint32_t DWC_CPU_TO_LE32(uint32_t *p)
-+{
-+#ifdef __LITTLE_ENDIAN
-+ return *p;
-+#else
-+ uint8_t *u_p = (uint8_t *)p;
-+
-+ return (u_p[3] | (u_p[2] << 8) | (u_p[1] << 16) | (u_p[0] << 24));
-+#endif
-+}
-+
-+uint32_t DWC_CPU_TO_BE32(uint32_t *p)
-+{
-+#ifdef __BIG_ENDIAN
-+ return *p;
-+#else
-+ uint8_t *u_p = (uint8_t *)p;
-+
-+ return (u_p[3] | (u_p[2] << 8) | (u_p[1] << 16) | (u_p[0] << 24));
-+#endif
-+}
-+
-+uint32_t DWC_LE32_TO_CPU(uint32_t *p)
-+{
-+#ifdef __LITTLE_ENDIAN
-+ return *p;
-+#else
-+ uint8_t *u_p = (uint8_t *)p;
-+
-+ return (u_p[3] | (u_p[2] << 8) | (u_p[1] << 16) | (u_p[0] << 24));
-+#endif
-+}
-+
-+uint32_t DWC_BE32_TO_CPU(uint32_t *p)
-+{
-+#ifdef __BIG_ENDIAN
-+ return *p;
-+#else
-+ uint8_t *u_p = (uint8_t *)p;
-+
-+ return (u_p[3] | (u_p[2] << 8) | (u_p[1] << 16) | (u_p[0] << 24));
-+#endif
-+}
-+
-+uint16_t DWC_CPU_TO_LE16(uint16_t *p)
-+{
-+#ifdef __LITTLE_ENDIAN
-+ return *p;
-+#else
-+ uint8_t *u_p = (uint8_t *)p;
-+ return (u_p[1] | (u_p[0] << 8));
-+#endif
-+}
-+
-+uint16_t DWC_CPU_TO_BE16(uint16_t *p)
-+{
-+#ifdef __BIG_ENDIAN
-+ return *p;
-+#else
-+ uint8_t *u_p = (uint8_t *)p;
-+ return (u_p[1] | (u_p[0] << 8));
-+#endif
-+}
-+
-+uint16_t DWC_LE16_TO_CPU(uint16_t *p)
-+{
-+#ifdef __LITTLE_ENDIAN
-+ return *p;
-+#else
-+ uint8_t *u_p = (uint8_t *)p;
-+ return (u_p[1] | (u_p[0] << 8));
-+#endif
-+}
-+
-+uint16_t DWC_BE16_TO_CPU(uint16_t *p)
-+{
-+#ifdef __BIG_ENDIAN
-+ return *p;
-+#else
-+ uint8_t *u_p = (uint8_t *)p;
-+ return (u_p[1] | (u_p[0] << 8));
-+#endif
-+}
-+
-+
-+/* Registers */
-+
-+uint32_t DWC_READ_REG32(uint32_t volatile *reg)
-+{
-+ return readl(reg);
-+}
-+
-+#if 0
-+uint64_t DWC_READ_REG64(uint64_t volatile *reg)
-+{
-+}
-+#endif
-+
-+void DWC_WRITE_REG32(uint32_t volatile *reg, uint32_t value)
-+{
-+ writel(value, reg);
-+}
-+
-+#if 0
-+void DWC_WRITE_REG64(uint64_t volatile *reg, uint64_t value)
-+{
-+}
-+#endif
-+
-+void DWC_MODIFY_REG32(uint32_t volatile *reg, uint32_t clear_mask, uint32_t set_mask)
-+{
-+ writel((readl(reg) & ~clear_mask) | set_mask, reg);
-+}
-+
-+#if 0
-+void DWC_MODIFY_REG64(uint64_t volatile *reg, uint64_t clear_mask, uint64_t set_mask)
-+{
-+}
-+#endif
-+
-+
-+/* Locking */
-+
-+dwc_spinlock_t *DWC_SPINLOCK_ALLOC(void)
-+{
-+ spinlock_t *sl = (spinlock_t *)1;
-+
-+#if defined(CONFIG_PREEMPT) || defined(CONFIG_SMP)
-+ sl = DWC_ALLOC(sizeof(*sl));
-+ if (!sl) {
-+ DWC_ERROR("Cannot allocate memory for spinlock\n");
-+ return NULL;
-+ }
-+
-+ spin_lock_init(sl);
-+#endif
-+ return (dwc_spinlock_t *)sl;
-+}
-+
-+void DWC_SPINLOCK_FREE(dwc_spinlock_t *lock)
-+{
-+#if defined(CONFIG_PREEMPT) || defined(CONFIG_SMP)
-+ DWC_FREE(lock);
-+#endif
-+}
-+
-+void DWC_SPINLOCK(dwc_spinlock_t *lock)
-+{
-+#if defined(CONFIG_PREEMPT) || defined(CONFIG_SMP)
-+ spin_lock((spinlock_t *)lock);
-+#endif
-+}
-+
-+void DWC_SPINUNLOCK(dwc_spinlock_t *lock)
-+{
-+#if defined(CONFIG_PREEMPT) || defined(CONFIG_SMP)
-+ spin_unlock((spinlock_t *)lock);
-+#endif
-+}
-+
-+void DWC_SPINLOCK_IRQSAVE(dwc_spinlock_t *lock, dwc_irqflags_t *flags)
-+{
-+ dwc_irqflags_t f;
-+
-+#if defined(CONFIG_PREEMPT) || defined(CONFIG_SMP)
-+ spin_lock_irqsave((spinlock_t *)lock, f);
-+#else
-+ local_irq_save(f);
-+#endif
-+ *flags = f;
-+}
-+
-+void DWC_SPINUNLOCK_IRQRESTORE(dwc_spinlock_t *lock, dwc_irqflags_t flags)
-+{
-+#if defined(CONFIG_PREEMPT) || defined(CONFIG_SMP)
-+ spin_unlock_irqrestore((spinlock_t *)lock, flags);
-+#else
-+ local_irq_restore(flags);
-+#endif
-+}
-+
-+dwc_mutex_t *DWC_MUTEX_ALLOC(void)
-+{
-+ struct mutex *m;
-+ dwc_mutex_t *mutex = (dwc_mutex_t *)DWC_ALLOC(sizeof(struct mutex));
-+
-+ if (!mutex) {
-+ DWC_ERROR("Cannot allocate memory for mutex\n");
-+ return NULL;
-+ }
-+
-+ m = (struct mutex *)mutex;
-+ mutex_init(m);
-+ return mutex;
-+}
-+
-+#if (defined(DWC_LINUX) && defined(CONFIG_DEBUG_MUTEXES))
-+#else
-+void DWC_MUTEX_FREE(dwc_mutex_t *mutex)
-+{
-+ mutex_destroy((struct mutex *)mutex);
-+ DWC_FREE(mutex);
-+}
-+#endif
-+
-+void DWC_MUTEX_LOCK(dwc_mutex_t *mutex)
-+{
-+ struct mutex *m = (struct mutex *)mutex;
-+ mutex_lock(m);
-+}
-+
-+int DWC_MUTEX_TRYLOCK(dwc_mutex_t *mutex)
-+{
-+ struct mutex *m = (struct mutex *)mutex;
-+ return mutex_trylock(m);
-+}
-+
-+void DWC_MUTEX_UNLOCK(dwc_mutex_t *mutex)
-+{
-+ struct mutex *m = (struct mutex *)mutex;
-+ mutex_unlock(m);
-+}
-+
-+
-+/* Timing */
-+
-+void DWC_UDELAY(uint32_t usecs)
-+{
-+ udelay(usecs);
-+}
-+
-+void DWC_MDELAY(uint32_t msecs)
-+{
-+ mdelay(msecs);
-+}
-+
-+void DWC_MSLEEP(uint32_t msecs)
-+{
-+ msleep(msecs);
-+}
-+
-+uint32_t DWC_TIME(void)
-+{
-+ return jiffies_to_msecs(jiffies);
-+}
-+
-+
-+/* Timers */
-+
-+struct dwc_timer {
-+ struct timer_list *t;
-+ char *name;
-+ dwc_timer_callback_t cb;
-+ void *data;
-+ uint8_t scheduled;
-+ dwc_spinlock_t *lock;
-+};
-+
-+static void timer_callback(unsigned long data)
-+{
-+ dwc_timer_t *timer = (dwc_timer_t *)data;
-+ dwc_irqflags_t flags;
-+
-+ DWC_SPINLOCK_IRQSAVE(timer->lock, &flags);
-+ timer->scheduled = 0;
-+ DWC_SPINUNLOCK_IRQRESTORE(timer->lock, flags);
-+ DWC_DEBUGC("Timer %s callback", timer->name);
-+ timer->cb(timer->data);
-+}
-+
-+dwc_timer_t *DWC_TIMER_ALLOC(char *name, dwc_timer_callback_t cb, void *data)
-+{
-+ dwc_timer_t *t = DWC_ALLOC(sizeof(*t));
-+
-+ if (!t) {
-+ DWC_ERROR("Cannot allocate memory for timer");
-+ return NULL;
-+ }
-+
-+ t->t = DWC_ALLOC(sizeof(*t->t));
-+ if (!t->t) {
-+ DWC_ERROR("Cannot allocate memory for timer->t");
-+ goto no_timer;
-+ }
-+
-+ t->name = DWC_STRDUP(name);
-+ if (!t->name) {
-+ DWC_ERROR("Cannot allocate memory for timer->name");
-+ goto no_name;
-+ }
-+
-+#if (defined(DWC_LINUX) && defined(CONFIG_DEBUG_SPINLOCK))
-+ DWC_SPINLOCK_ALLOC_LINUX_DEBUG(t->lock);
-+#else
-+ t->lock = DWC_SPINLOCK_ALLOC();
-+#endif
-+ if (!t->lock) {
-+ DWC_ERROR("Cannot allocate memory for lock");
-+ goto no_lock;
-+ }
-+
-+ t->scheduled = 0;
-+ t->t->expires = jiffies;
-+ setup_timer(t->t, timer_callback, (unsigned long)t);
-+
-+ t->cb = cb;
-+ t->data = data;
-+
-+ return t;
-+
-+ no_lock:
-+ DWC_FREE(t->name);
-+ no_name:
-+ DWC_FREE(t->t);
-+ no_timer:
-+ DWC_FREE(t);
-+ return NULL;
-+}
-+
-+void DWC_TIMER_FREE(dwc_timer_t *timer)
-+{
-+ dwc_irqflags_t flags;
-+
-+ DWC_SPINLOCK_IRQSAVE(timer->lock, &flags);
-+
-+ if (timer->scheduled) {
-+ del_timer(timer->t);
-+ timer->scheduled = 0;
-+ }
-+
-+ DWC_SPINUNLOCK_IRQRESTORE(timer->lock, flags);
-+ DWC_SPINLOCK_FREE(timer->lock);
-+ DWC_FREE(timer->t);
-+ DWC_FREE(timer->name);
-+ DWC_FREE(timer);
-+}
-+
-+void DWC_TIMER_SCHEDULE(dwc_timer_t *timer, uint32_t time)
-+{
-+ dwc_irqflags_t flags;
-+
-+ DWC_SPINLOCK_IRQSAVE(timer->lock, &flags);
-+
-+ if (!timer->scheduled) {
-+ timer->scheduled = 1;
-+ DWC_DEBUGC("Scheduling timer %s to expire in +%d msec", timer->name, time);
-+ timer->t->expires = jiffies + msecs_to_jiffies(time);
-+ add_timer(timer->t);
-+ } else {
-+ DWC_DEBUGC("Modifying timer %s to expire in +%d msec", timer->name, time);
-+ mod_timer(timer->t, jiffies + msecs_to_jiffies(time));
-+ }
-+
-+ DWC_SPINUNLOCK_IRQRESTORE(timer->lock, flags);
-+}
-+
-+void DWC_TIMER_CANCEL(dwc_timer_t *timer)
-+{
-+ del_timer(timer->t);
-+}
-+
-+
-+/* Wait Queues */
-+
-+struct dwc_waitq {
-+ wait_queue_head_t queue;
-+ int abort;
-+};
-+
-+dwc_waitq_t *DWC_WAITQ_ALLOC(void)
-+{
-+ dwc_waitq_t *wq = DWC_ALLOC(sizeof(*wq));
-+
-+ if (!wq) {
-+ DWC_ERROR("Cannot allocate memory for waitqueue\n");
-+ return NULL;
-+ }
-+
-+ init_waitqueue_head(&wq->queue);
-+ wq->abort = 0;
-+ return wq;
-+}
-+
-+void DWC_WAITQ_FREE(dwc_waitq_t *wq)
-+{
-+ DWC_FREE(wq);
-+}
-+
-+int32_t DWC_WAITQ_WAIT(dwc_waitq_t *wq, dwc_waitq_condition_t cond, void *data)
-+{
-+ int result = wait_event_interruptible(wq->queue,
-+ cond(data) || wq->abort);
-+ if (result == -ERESTARTSYS) {
-+ wq->abort = 0;
-+ return -DWC_E_RESTART;
-+ }
-+
-+ if (wq->abort == 1) {
-+ wq->abort = 0;
-+ return -DWC_E_ABORT;
-+ }
-+
-+ wq->abort = 0;
-+
-+ if (result == 0) {
-+ return 0;
-+ }
-+
-+ return -DWC_E_UNKNOWN;
-+}
-+
-+int32_t DWC_WAITQ_WAIT_TIMEOUT(dwc_waitq_t *wq, dwc_waitq_condition_t cond,
-+ void *data, int32_t msecs)
-+{
-+ int32_t tmsecs;
-+ int result = wait_event_interruptible_timeout(wq->queue,
-+ cond(data) || wq->abort,
-+ msecs_to_jiffies(msecs));
-+ if (result == -ERESTARTSYS) {
-+ wq->abort = 0;
-+ return -DWC_E_RESTART;
-+ }
-+
-+ if (wq->abort == 1) {
-+ wq->abort = 0;
-+ return -DWC_E_ABORT;
-+ }
-+
-+ wq->abort = 0;
-+
-+ if (result > 0) {
-+ tmsecs = jiffies_to_msecs(result);
-+ if (!tmsecs) {
-+ return 1;
-+ }
-+
-+ return tmsecs;
-+ }
-+
-+ if (result == 0) {
-+ return -DWC_E_TIMEOUT;
-+ }
-+
-+ return -DWC_E_UNKNOWN;
-+}
-+
-+void DWC_WAITQ_TRIGGER(dwc_waitq_t *wq)
-+{
-+ wq->abort = 0;
-+ wake_up_interruptible(&wq->queue);
-+}
-+
-+void DWC_WAITQ_ABORT(dwc_waitq_t *wq)
-+{
-+ wq->abort = 1;
-+ wake_up_interruptible(&wq->queue);
-+}
-+
-+
-+/* Threading */
-+
-+dwc_thread_t *DWC_THREAD_RUN(dwc_thread_function_t func, char *name, void *data)
-+{
-+ struct task_struct *thread = kthread_run(func, data, name);
-+
-+ if (thread == ERR_PTR(-ENOMEM)) {
-+ return NULL;
-+ }
-+
-+ return (dwc_thread_t *)thread;
-+}
-+
-+int DWC_THREAD_STOP(dwc_thread_t *thread)
-+{
-+ return kthread_stop((struct task_struct *)thread);
-+}
-+
-+dwc_bool_t DWC_THREAD_SHOULD_STOP(void)
-+{
-+ return kthread_should_stop();
-+}
-+
-+
-+/* tasklets
-+ - run in interrupt context (cannot sleep)
-+ - each tasklet runs on a single CPU
-+ - different tasklets can be running simultaneously on different CPUs
-+ */
-+struct dwc_tasklet {
-+ struct tasklet_struct t;
-+ dwc_tasklet_callback_t cb;
-+ void *data;
-+};
-+
-+static void tasklet_callback(unsigned long data)
-+{
-+ dwc_tasklet_t *t = (dwc_tasklet_t *)data;
-+ t->cb(t->data);
-+}
-+
-+dwc_tasklet_t *DWC_TASK_ALLOC(char *name, dwc_tasklet_callback_t cb, void *data)
-+{
-+ dwc_tasklet_t *t = DWC_ALLOC(sizeof(*t));
-+
-+ if (t) {
-+ t->cb = cb;
-+ t->data = data;
-+ tasklet_init(&t->t, tasklet_callback, (unsigned long)t);
-+ } else {
-+ DWC_ERROR("Cannot allocate memory for tasklet\n");
-+ }
-+
-+ return t;
-+}
-+
-+void DWC_TASK_FREE(dwc_tasklet_t *task)
-+{
-+ DWC_FREE(task);
-+}
-+
-+void DWC_TASK_SCHEDULE(dwc_tasklet_t *task)
-+{
-+ tasklet_schedule(&task->t);
-+}
-+
-+void DWC_TASK_HI_SCHEDULE(dwc_tasklet_t *task)
-+{
-+ tasklet_hi_schedule(&task->t);
-+}
-+
-+
-+/* workqueues
-+ - run in process context (can sleep)
-+ */
-+typedef struct work_container {
-+ dwc_work_callback_t cb;
-+ void *data;
-+ dwc_workq_t *wq;
-+ char *name;
-+
-+#ifdef DEBUG
-+ DWC_CIRCLEQ_ENTRY(work_container) entry;
-+#endif
-+ struct delayed_work work;
-+} work_container_t;
-+
-+#ifdef DEBUG
-+DWC_CIRCLEQ_HEAD(work_container_queue, work_container);
-+#endif
-+
-+struct dwc_workq {
-+ struct workqueue_struct *wq;
-+ dwc_spinlock_t *lock;
-+ dwc_waitq_t *waitq;
-+ int pending;
-+
-+#ifdef DEBUG
-+ struct work_container_queue entries;
-+#endif
-+};
-+
-+static void do_work(struct work_struct *work)
-+{
-+ dwc_irqflags_t flags;
-+ struct delayed_work *dw = container_of(work, struct delayed_work, work);
-+ work_container_t *container = container_of(dw, struct work_container, work);
-+ dwc_workq_t *wq = container->wq;
-+
-+ container->cb(container->data);
-+
-+#ifdef DEBUG
-+ DWC_CIRCLEQ_REMOVE(&wq->entries, container, entry);
-+#endif
-+ DWC_DEBUGC("Work done: %s, container=%p", container->name, container);
-+ if (container->name) {
-+ DWC_FREE(container->name);
-+ }
-+ DWC_FREE(container);
-+
-+ DWC_SPINLOCK_IRQSAVE(wq->lock, &flags);
-+ wq->pending--;
-+ DWC_SPINUNLOCK_IRQRESTORE(wq->lock, flags);
-+ DWC_WAITQ_TRIGGER(wq->waitq);
-+}
-+
-+static int work_done(void *data)
-+{
-+ dwc_workq_t *workq = (dwc_workq_t *)data;
-+ return workq->pending == 0;
-+}
-+
-+int DWC_WORKQ_WAIT_WORK_DONE(dwc_workq_t *workq, int timeout)
-+{
-+ return DWC_WAITQ_WAIT_TIMEOUT(workq->waitq, work_done, workq, timeout);
-+}
-+
-+dwc_workq_t *DWC_WORKQ_ALLOC(char *name)
-+{
-+ dwc_workq_t *wq = DWC_ALLOC(sizeof(*wq));
-+
-+ if (!wq) {
-+ return NULL;
-+ }
-+
-+ wq->wq = create_singlethread_workqueue(name);
-+ if (!wq->wq) {
-+ goto no_wq;
-+ }
-+
-+ wq->pending = 0;
-+
-+#if (defined(DWC_LINUX) && defined(CONFIG_DEBUG_SPINLOCK))
-+ DWC_SPINLOCK_ALLOC_LINUX_DEBUG(wq->lock);
-+#else
-+ wq->lock = DWC_SPINLOCK_ALLOC();
-+#endif
-+ if (!wq->lock) {
-+ goto no_lock;
-+ }
-+
-+ wq->waitq = DWC_WAITQ_ALLOC();
-+ if (!wq->waitq) {
-+ goto no_waitq;
-+ }
-+
-+#ifdef DEBUG
-+ DWC_CIRCLEQ_INIT(&wq->entries);
-+#endif
-+ return wq;
-+
-+ no_waitq:
-+ DWC_SPINLOCK_FREE(wq->lock);
-+ no_lock:
-+ destroy_workqueue(wq->wq);
-+ no_wq:
-+ DWC_FREE(wq);
-+
-+ return NULL;
-+}
-+
-+void DWC_WORKQ_FREE(dwc_workq_t *wq)
-+{
-+#ifdef DEBUG
-+ if (wq->pending != 0) {
-+ struct work_container *wc;
-+ DWC_ERROR("Destroying work queue with pending work");
-+ DWC_CIRCLEQ_FOREACH(wc, &wq->entries, entry) {
-+ DWC_ERROR("Work %s still pending", wc->name);
-+ }
-+ }
-+#endif
-+ destroy_workqueue(wq->wq);
-+ DWC_SPINLOCK_FREE(wq->lock);
-+ DWC_WAITQ_FREE(wq->waitq);
-+ DWC_FREE(wq);
-+}
-+
-+void DWC_WORKQ_SCHEDULE(dwc_workq_t *wq, dwc_work_callback_t cb, void *data,
-+ char *format, ...)
-+{
-+ dwc_irqflags_t flags;
-+ work_container_t *container;
-+ static char name[128];
-+ va_list args;
-+
-+ va_start(args, format);
-+ DWC_VSNPRINTF(name, 128, format, args);
-+ va_end(args);
-+
-+ DWC_SPINLOCK_IRQSAVE(wq->lock, &flags);
-+ wq->pending++;
-+ DWC_SPINUNLOCK_IRQRESTORE(wq->lock, flags);
-+ DWC_WAITQ_TRIGGER(wq->waitq);
-+
-+ container = DWC_ALLOC_ATOMIC(sizeof(*container));
-+ if (!container) {
-+ DWC_ERROR("Cannot allocate memory for container\n");
-+ return;
-+ }
-+
-+ container->name = DWC_STRDUP(name);
-+ if (!container->name) {
-+ DWC_ERROR("Cannot allocate memory for container->name\n");
-+ DWC_FREE(container);
-+ return;
-+ }
-+
-+ container->cb = cb;
-+ container->data = data;
-+ container->wq = wq;
-+ DWC_DEBUGC("Queueing work: %s, container=%p", container->name, container);
-+ INIT_WORK(&container->work.work, do_work);
-+
-+#ifdef DEBUG
-+ DWC_CIRCLEQ_INSERT_TAIL(&wq->entries, container, entry);
-+#endif
-+ queue_work(wq->wq, &container->work.work);
-+}
-+
-+void DWC_WORKQ_SCHEDULE_DELAYED(dwc_workq_t *wq, dwc_work_callback_t cb,
-+ void *data, uint32_t time, char *format, ...)
-+{
-+ dwc_irqflags_t flags;
-+ work_container_t *container;
-+ static char name[128];
-+ va_list args;
-+
-+ va_start(args, format);
-+ DWC_VSNPRINTF(name, 128, format, args);
-+ va_end(args);
-+
-+ DWC_SPINLOCK_IRQSAVE(wq->lock, &flags);
-+ wq->pending++;
-+ DWC_SPINUNLOCK_IRQRESTORE(wq->lock, flags);
-+ DWC_WAITQ_TRIGGER(wq->waitq);
-+
-+ container = DWC_ALLOC_ATOMIC(sizeof(*container));
-+ if (!container) {
-+ DWC_ERROR("Cannot allocate memory for container\n");
-+ return;
-+ }
-+
-+ container->name = DWC_STRDUP(name);
-+ if (!container->name) {
-+ DWC_ERROR("Cannot allocate memory for container->name\n");
-+ DWC_FREE(container);
-+ return;
-+ }
-+
-+ container->cb = cb;
-+ container->data = data;
-+ container->wq = wq;
-+ DWC_DEBUGC("Queueing work: %s, container=%p", container->name, container);
-+ INIT_DELAYED_WORK(&container->work, do_work);
-+
-+#ifdef DEBUG
-+ DWC_CIRCLEQ_INSERT_TAIL(&wq->entries, container, entry);
-+#endif
-+ queue_delayed_work(wq->wq, &container->work, msecs_to_jiffies(time));
-+}
-+
-+int DWC_WORKQ_PENDING(dwc_workq_t *wq)
-+{
-+ return wq->pending;
-+}
-+
-+
-+#ifdef DWC_LIBMODULE
-+
-+#ifdef DWC_CCLIB
-+/* CC */
-+EXPORT_SYMBOL(dwc_cc_if_alloc);
-+EXPORT_SYMBOL(dwc_cc_if_free);
-+EXPORT_SYMBOL(dwc_cc_clear);
-+EXPORT_SYMBOL(dwc_cc_add);
-+EXPORT_SYMBOL(dwc_cc_remove);
-+EXPORT_SYMBOL(dwc_cc_change);
-+EXPORT_SYMBOL(dwc_cc_data_for_save);
-+EXPORT_SYMBOL(dwc_cc_restore_from_data);
-+EXPORT_SYMBOL(dwc_cc_match_chid);
-+EXPORT_SYMBOL(dwc_cc_match_cdid);
-+EXPORT_SYMBOL(dwc_cc_ck);
-+EXPORT_SYMBOL(dwc_cc_chid);
-+EXPORT_SYMBOL(dwc_cc_cdid);
-+EXPORT_SYMBOL(dwc_cc_name);
-+#endif /* DWC_CCLIB */
-+
-+#ifdef DWC_CRYPTOLIB
-+# ifndef CONFIG_MACH_IPMATE
-+/* Modpow */
-+EXPORT_SYMBOL(dwc_modpow);
-+
-+/* DH */
-+EXPORT_SYMBOL(dwc_dh_modpow);
-+EXPORT_SYMBOL(dwc_dh_derive_keys);
-+EXPORT_SYMBOL(dwc_dh_pk);
-+# endif /* CONFIG_MACH_IPMATE */
-+
-+/* Crypto */
-+EXPORT_SYMBOL(dwc_wusb_aes_encrypt);
-+EXPORT_SYMBOL(dwc_wusb_cmf);
-+EXPORT_SYMBOL(dwc_wusb_prf);
-+EXPORT_SYMBOL(dwc_wusb_fill_ccm_nonce);
-+EXPORT_SYMBOL(dwc_wusb_gen_nonce);
-+EXPORT_SYMBOL(dwc_wusb_gen_key);
-+EXPORT_SYMBOL(dwc_wusb_gen_mic);
-+#endif /* DWC_CRYPTOLIB */
-+
-+/* Notification */
-+#ifdef DWC_NOTIFYLIB
-+EXPORT_SYMBOL(dwc_alloc_notification_manager);
-+EXPORT_SYMBOL(dwc_free_notification_manager);
-+EXPORT_SYMBOL(dwc_register_notifier);
-+EXPORT_SYMBOL(dwc_unregister_notifier);
-+EXPORT_SYMBOL(dwc_add_observer);
-+EXPORT_SYMBOL(dwc_remove_observer);
-+EXPORT_SYMBOL(dwc_notify);
-+#endif
-+
-+/* Memory Debugging Routines */
-+#ifdef DWC_DEBUG_MEMORY
-+EXPORT_SYMBOL(dwc_alloc_debug);
-+EXPORT_SYMBOL(dwc_alloc_atomic_debug);
-+EXPORT_SYMBOL(dwc_free_debug);
-+EXPORT_SYMBOL(dwc_dma_alloc_debug);
-+EXPORT_SYMBOL(dwc_dma_free_debug);
-+#endif
-+
-+EXPORT_SYMBOL(DWC_MEMSET);
-+EXPORT_SYMBOL(DWC_MEMCPY);
-+EXPORT_SYMBOL(DWC_MEMMOVE);
-+EXPORT_SYMBOL(DWC_MEMCMP);
-+EXPORT_SYMBOL(DWC_STRNCMP);
-+EXPORT_SYMBOL(DWC_STRCMP);
-+EXPORT_SYMBOL(DWC_STRLEN);
-+EXPORT_SYMBOL(DWC_STRCPY);
-+EXPORT_SYMBOL(DWC_STRDUP);
-+EXPORT_SYMBOL(DWC_ATOI);
-+EXPORT_SYMBOL(DWC_ATOUI);
-+
-+#ifdef DWC_UTFLIB
-+EXPORT_SYMBOL(DWC_UTF8_TO_UTF16LE);
-+#endif /* DWC_UTFLIB */
-+
-+EXPORT_SYMBOL(DWC_IN_IRQ);
-+EXPORT_SYMBOL(DWC_IN_BH);
-+EXPORT_SYMBOL(DWC_VPRINTF);
-+EXPORT_SYMBOL(DWC_VSNPRINTF);
-+EXPORT_SYMBOL(DWC_PRINTF);
-+EXPORT_SYMBOL(DWC_SPRINTF);
-+EXPORT_SYMBOL(DWC_SNPRINTF);
-+EXPORT_SYMBOL(__DWC_WARN);
-+EXPORT_SYMBOL(__DWC_ERROR);
-+EXPORT_SYMBOL(DWC_EXCEPTION);
-+
-+#ifdef DEBUG
-+EXPORT_SYMBOL(__DWC_DEBUG);
-+#endif
-+
-+EXPORT_SYMBOL(__DWC_DMA_ALLOC);
-+EXPORT_SYMBOL(__DWC_DMA_ALLOC_ATOMIC);
-+EXPORT_SYMBOL(__DWC_DMA_FREE);
-+EXPORT_SYMBOL(__DWC_ALLOC);
-+EXPORT_SYMBOL(__DWC_ALLOC_ATOMIC);
-+EXPORT_SYMBOL(__DWC_FREE);
-+
-+#ifdef DWC_CRYPTOLIB
-+EXPORT_SYMBOL(DWC_RANDOM_BYTES);
-+EXPORT_SYMBOL(DWC_AES_CBC);
-+EXPORT_SYMBOL(DWC_SHA256);
-+EXPORT_SYMBOL(DWC_HMAC_SHA256);
-+#endif
-+
-+EXPORT_SYMBOL(DWC_CPU_TO_LE32);
-+EXPORT_SYMBOL(DWC_CPU_TO_BE32);
-+EXPORT_SYMBOL(DWC_LE32_TO_CPU);
-+EXPORT_SYMBOL(DWC_BE32_TO_CPU);
-+EXPORT_SYMBOL(DWC_CPU_TO_LE16);
-+EXPORT_SYMBOL(DWC_CPU_TO_BE16);
-+EXPORT_SYMBOL(DWC_LE16_TO_CPU);
-+EXPORT_SYMBOL(DWC_BE16_TO_CPU);
-+EXPORT_SYMBOL(DWC_READ_REG32);
-+EXPORT_SYMBOL(DWC_WRITE_REG32);
-+EXPORT_SYMBOL(DWC_MODIFY_REG32);
-+
-+#if 0
-+EXPORT_SYMBOL(DWC_READ_REG64);
-+EXPORT_SYMBOL(DWC_WRITE_REG64);
-+EXPORT_SYMBOL(DWC_MODIFY_REG64);
-+#endif
-+
-+EXPORT_SYMBOL(DWC_SPINLOCK_ALLOC);
-+EXPORT_SYMBOL(DWC_SPINLOCK_FREE);
-+EXPORT_SYMBOL(DWC_SPINLOCK);
-+EXPORT_SYMBOL(DWC_SPINUNLOCK);
-+EXPORT_SYMBOL(DWC_SPINLOCK_IRQSAVE);
-+EXPORT_SYMBOL(DWC_SPINUNLOCK_IRQRESTORE);
-+EXPORT_SYMBOL(DWC_MUTEX_ALLOC);
-+
-+#if (!defined(DWC_LINUX) || !defined(CONFIG_DEBUG_MUTEXES))
-+EXPORT_SYMBOL(DWC_MUTEX_FREE);
-+#endif
-+
-+EXPORT_SYMBOL(DWC_MUTEX_LOCK);
-+EXPORT_SYMBOL(DWC_MUTEX_TRYLOCK);
-+EXPORT_SYMBOL(DWC_MUTEX_UNLOCK);
-+EXPORT_SYMBOL(DWC_UDELAY);
-+EXPORT_SYMBOL(DWC_MDELAY);
-+EXPORT_SYMBOL(DWC_MSLEEP);
-+EXPORT_SYMBOL(DWC_TIME);
-+EXPORT_SYMBOL(DWC_TIMER_ALLOC);
-+EXPORT_SYMBOL(DWC_TIMER_FREE);
-+EXPORT_SYMBOL(DWC_TIMER_SCHEDULE);
-+EXPORT_SYMBOL(DWC_TIMER_CANCEL);
-+EXPORT_SYMBOL(DWC_WAITQ_ALLOC);
-+EXPORT_SYMBOL(DWC_WAITQ_FREE);
-+EXPORT_SYMBOL(DWC_WAITQ_WAIT);
-+EXPORT_SYMBOL(DWC_WAITQ_WAIT_TIMEOUT);
-+EXPORT_SYMBOL(DWC_WAITQ_TRIGGER);
-+EXPORT_SYMBOL(DWC_WAITQ_ABORT);
-+EXPORT_SYMBOL(DWC_THREAD_RUN);
-+EXPORT_SYMBOL(DWC_THREAD_STOP);
-+EXPORT_SYMBOL(DWC_THREAD_SHOULD_STOP);
-+EXPORT_SYMBOL(DWC_TASK_ALLOC);
-+EXPORT_SYMBOL(DWC_TASK_FREE);
-+EXPORT_SYMBOL(DWC_TASK_SCHEDULE);
-+EXPORT_SYMBOL(DWC_WORKQ_WAIT_WORK_DONE);
-+EXPORT_SYMBOL(DWC_WORKQ_ALLOC);
-+EXPORT_SYMBOL(DWC_WORKQ_FREE);
-+EXPORT_SYMBOL(DWC_WORKQ_SCHEDULE);
-+EXPORT_SYMBOL(DWC_WORKQ_SCHEDULE_DELAYED);
-+EXPORT_SYMBOL(DWC_WORKQ_PENDING);
-+
-+static int dwc_common_port_init_module(void)
-+{
-+ int result = 0;
-+
-+ printk(KERN_DEBUG "Module dwc_common_port init\n" );
-+
-+#ifdef DWC_DEBUG_MEMORY
-+ result = dwc_memory_debug_start(NULL);
-+ if (result) {
-+ printk(KERN_ERR
-+ "dwc_memory_debug_start() failed with error %d\n",
-+ result);
-+ return result;
-+ }
-+#endif
-+
-+#ifdef DWC_NOTIFYLIB
-+ result = dwc_alloc_notification_manager(NULL, NULL);
-+ if (result) {
-+ printk(KERN_ERR
-+ "dwc_alloc_notification_manager() failed with error %d\n",
-+ result);
-+ return result;
-+ }
-+#endif
-+ return result;
-+}
-+
-+static void dwc_common_port_exit_module(void)
-+{
-+ printk(KERN_DEBUG "Module dwc_common_port exit\n" );
-+
-+#ifdef DWC_NOTIFYLIB
-+ dwc_free_notification_manager();
-+#endif
-+
-+#ifdef DWC_DEBUG_MEMORY
-+ dwc_memory_debug_stop();
-+#endif
-+}
-+
-+module_init(dwc_common_port_init_module);
-+module_exit(dwc_common_port_exit_module);
-+
-+MODULE_DESCRIPTION("DWC Common Library - Portable version");
-+MODULE_AUTHOR("Synopsys Inc.");
-+MODULE_LICENSE ("GPL");
-+
-+#endif /* DWC_LIBMODULE */
---- /dev/null
-+++ b/drivers/usb/host/dwc_common_port/dwc_common_nbsd.c
-@@ -0,0 +1,1275 @@
-+#include "dwc_os.h"
-+#include "dwc_list.h"
-+
-+#ifdef DWC_CCLIB
-+# include "dwc_cc.h"
-+#endif
-+
-+#ifdef DWC_CRYPTOLIB
-+# include "dwc_modpow.h"
-+# include "dwc_dh.h"
-+# include "dwc_crypto.h"
-+#endif
-+
-+#ifdef DWC_NOTIFYLIB
-+# include "dwc_notifier.h"
-+#endif
-+
-+/* OS-Level Implementations */
-+
-+/* This is the NetBSD 4.0.1 kernel implementation of the DWC platform library. */
-+
-+
-+/* MISC */
-+
-+void *DWC_MEMSET(void *dest, uint8_t byte, uint32_t size)
-+{
-+ return memset(dest, byte, size);
-+}
-+
-+void *DWC_MEMCPY(void *dest, void const *src, uint32_t size)
-+{
-+ return memcpy(dest, src, size);
-+}
-+
-+void *DWC_MEMMOVE(void *dest, void *src, uint32_t size)
-+{
-+ bcopy(src, dest, size);
-+ return dest;
-+}
-+
-+int DWC_MEMCMP(void *m1, void *m2, uint32_t size)
-+{
-+ return memcmp(m1, m2, size);
-+}
-+
-+int DWC_STRNCMP(void *s1, void *s2, uint32_t size)
-+{
-+ return strncmp(s1, s2, size);
-+}
-+
-+int DWC_STRCMP(void *s1, void *s2)
-+{
-+ return strcmp(s1, s2);
-+}
-+
-+int DWC_STRLEN(char const *str)
-+{
-+ return strlen(str);
-+}
-+
-+char *DWC_STRCPY(char *to, char const *from)
-+{
-+ return strcpy(to, from);
-+}
-+
-+char *DWC_STRDUP(char const *str)
-+{
-+ int len = DWC_STRLEN(str) + 1;
-+ char *new = DWC_ALLOC_ATOMIC(len);
-+
-+ if (!new) {
-+ return NULL;
-+ }
-+
-+ DWC_MEMCPY(new, str, len);
-+ return new;
-+}
-+
-+int DWC_ATOI(char *str, int32_t *value)
-+{
-+ char *end = NULL;
-+
-+ /* NetBSD doesn't have 'strtol' in the kernel, but 'strtoul'
-+ * should be equivalent on 2's complement machines
-+ */
-+ *value = strtoul(str, &end, 0);
-+ if (*end == '\0') {
-+ return 0;
-+ }
-+
-+ return -1;
-+}
-+
-+int DWC_ATOUI(char *str, uint32_t *value)
-+{
-+ char *end = NULL;
-+
-+ *value = strtoul(str, &end, 0);
-+ if (*end == '\0') {
-+ return 0;
-+ }
-+
-+ return -1;
-+}
-+
-+
-+#ifdef DWC_UTFLIB
-+/* From usbstring.c */
-+
-+int DWC_UTF8_TO_UTF16LE(uint8_t const *s, uint16_t *cp, unsigned len)
-+{
-+ int count = 0;
-+ u8 c;
-+ u16 uchar;
-+
-+ /* this insists on correct encodings, though not minimal ones.
-+ * BUT it currently rejects legit 4-byte UTF-8 code points,
-+ * which need surrogate pairs. (Unicode 3.1 can use them.)
-+ */
-+ while (len != 0 && (c = (u8) *s++) != 0) {
-+ if (unlikely(c & 0x80)) {
-+ // 2-byte sequence:
-+ // 00000yyyyyxxxxxx = 110yyyyy 10xxxxxx
-+ if ((c & 0xe0) == 0xc0) {
-+ uchar = (c & 0x1f) << 6;
-+
-+ c = (u8) *s++;
-+ if ((c & 0xc0) != 0xc0)
-+ goto fail;
-+ c &= 0x3f;
-+ uchar |= c;
-+
-+ // 3-byte sequence (most CJKV characters):
-+ // zzzzyyyyyyxxxxxx = 1110zzzz 10yyyyyy 10xxxxxx
-+ } else if ((c & 0xf0) == 0xe0) {
-+ uchar = (c & 0x0f) << 12;
-+
-+ c = (u8) *s++;
-+ if ((c & 0xc0) != 0xc0)
-+ goto fail;
-+ c &= 0x3f;
-+ uchar |= c << 6;
-+
-+ c = (u8) *s++;
-+ if ((c & 0xc0) != 0xc0)
-+ goto fail;
-+ c &= 0x3f;
-+ uchar |= c;
-+
-+ /* no bogus surrogates */
-+ if (0xd800 <= uchar && uchar <= 0xdfff)
-+ goto fail;
-+
-+ // 4-byte sequence (surrogate pairs, currently rare):
-+ // 11101110wwwwzzzzyy + 110111yyyyxxxxxx
-+ // = 11110uuu 10uuzzzz 10yyyyyy 10xxxxxx
-+ // (uuuuu = wwww + 1)
-+ // FIXME accept the surrogate code points (only)
-+ } else
-+ goto fail;
-+ } else
-+ uchar = c;
-+ put_unaligned (cpu_to_le16 (uchar), cp++);
-+ count++;
-+ len--;
-+ }
-+ return count;
-+fail:
-+ return -1;
-+}
-+
-+#endif /* DWC_UTFLIB */
-+
-+
-+/* dwc_debug.h */
-+
-+dwc_bool_t DWC_IN_IRQ(void)
-+{
-+// return in_irq();
-+ return 0;
-+}
-+
-+dwc_bool_t DWC_IN_BH(void)
-+{
-+// return in_softirq();
-+ return 0;
-+}
-+
-+void DWC_VPRINTF(char *format, va_list args)
-+{
-+ vprintf(format, args);
-+}
-+
-+int DWC_VSNPRINTF(char *str, int size, char *format, va_list args)
-+{
-+ return vsnprintf(str, size, format, args);
-+}
-+
-+void DWC_PRINTF(char *format, ...)
-+{
-+ va_list args;
-+
-+ va_start(args, format);
-+ DWC_VPRINTF(format, args);
-+ va_end(args);
-+}
-+
-+int DWC_SPRINTF(char *buffer, char *format, ...)
-+{
-+ int retval;
-+ va_list args;
-+
-+ va_start(args, format);
-+ retval = vsprintf(buffer, format, args);
-+ va_end(args);
-+ return retval;
-+}
-+
-+int DWC_SNPRINTF(char *buffer, int size, char *format, ...)
-+{
-+ int retval;
-+ va_list args;
-+
-+ va_start(args, format);
-+ retval = vsnprintf(buffer, size, format, args);
-+ va_end(args);
-+ return retval;
-+}
-+
-+void __DWC_WARN(char *format, ...)
-+{
-+ va_list args;
-+
-+ va_start(args, format);
-+ DWC_VPRINTF(format, args);
-+ va_end(args);
-+}
-+
-+void __DWC_ERROR(char *format, ...)
-+{
-+ va_list args;
-+
-+ va_start(args, format);
-+ DWC_VPRINTF(format, args);
-+ va_end(args);
-+}
-+
-+void DWC_EXCEPTION(char *format, ...)
-+{
-+ va_list args;
-+
-+ va_start(args, format);
-+ DWC_VPRINTF(format, args);
-+ va_end(args);
-+// BUG_ON(1); ???
-+}
-+
-+#ifdef DEBUG
-+void __DWC_DEBUG(char *format, ...)
-+{
-+ va_list args;
-+
-+ va_start(args, format);
-+ DWC_VPRINTF(format, args);
-+ va_end(args);
-+}
-+#endif
-+
-+
-+/* dwc_mem.h */
-+
-+#if 0
-+dwc_pool_t *DWC_DMA_POOL_CREATE(uint32_t size,
-+ uint32_t align,
-+ uint32_t alloc)
-+{
-+ struct dma_pool *pool = dma_pool_create("Pool", NULL,
-+ size, align, alloc);
-+ return (dwc_pool_t *)pool;
-+}
-+
-+void DWC_DMA_POOL_DESTROY(dwc_pool_t *pool)
-+{
-+ dma_pool_destroy((struct dma_pool *)pool);
-+}
-+
-+void *DWC_DMA_POOL_ALLOC(dwc_pool_t *pool, uint64_t *dma_addr)
-+{
-+// return dma_pool_alloc((struct dma_pool *)pool, GFP_KERNEL, dma_addr);
-+ return dma_pool_alloc((struct dma_pool *)pool, M_WAITOK, dma_addr);
-+}
-+
-+void *DWC_DMA_POOL_ZALLOC(dwc_pool_t *pool, uint64_t *dma_addr)
-+{
-+ void *vaddr = DWC_DMA_POOL_ALLOC(pool, dma_addr);
-+ memset(..);
-+}
-+
-+void DWC_DMA_POOL_FREE(dwc_pool_t *pool, void *vaddr, void *daddr)
-+{
-+ dma_pool_free(pool, vaddr, daddr);
-+}
-+#endif
-+
-+void *__DWC_DMA_ALLOC(void *dma_ctx, uint32_t size, dwc_dma_t *dma_addr)
-+{
-+ dwc_dmactx_t *dma = (dwc_dmactx_t *)dma_ctx;
-+ int error;
-+
-+ error = bus_dmamem_alloc(dma->dma_tag, size, 1, size, dma->segs,
-+ sizeof(dma->segs) / sizeof(dma->segs[0]),
-+ &dma->nsegs, BUS_DMA_NOWAIT);
-+ if (error) {
-+ printf("%s: bus_dmamem_alloc(%ju) failed: %d\n", __func__,
-+ (uintmax_t)size, error);
-+ goto fail_0;
-+ }
-+
-+ error = bus_dmamem_map(dma->dma_tag, dma->segs, dma->nsegs, size,
-+ (caddr_t *)&dma->dma_vaddr,
-+ BUS_DMA_NOWAIT | BUS_DMA_COHERENT);
-+ if (error) {
-+ printf("%s: bus_dmamem_map failed: %d\n", __func__, error);
-+ goto fail_1;
-+ }
-+
-+ error = bus_dmamap_create(dma->dma_tag, size, 1, size, 0,
-+ BUS_DMA_NOWAIT, &dma->dma_map);
-+ if (error) {
-+ printf("%s: bus_dmamap_create failed: %d\n", __func__, error);
-+ goto fail_2;
-+ }
-+
-+ error = bus_dmamap_load(dma->dma_tag, dma->dma_map, dma->dma_vaddr,
-+ size, NULL, BUS_DMA_NOWAIT);
-+ if (error) {
-+ printf("%s: bus_dmamap_load failed: %d\n", __func__, error);
-+ goto fail_3;
-+ }
-+
-+ dma->dma_paddr = (bus_addr_t)dma->segs[0].ds_addr;
-+ *dma_addr = dma->dma_paddr;
-+ return dma->dma_vaddr;
-+
-+fail_3:
-+ bus_dmamap_destroy(dma->dma_tag, dma->dma_map);
-+fail_2:
-+ bus_dmamem_unmap(dma->dma_tag, dma->dma_vaddr, size);
-+fail_1:
-+ bus_dmamem_free(dma->dma_tag, dma->segs, dma->nsegs);
-+fail_0:
-+ dma->dma_map = NULL;
-+ dma->dma_vaddr = NULL;
-+ dma->nsegs = 0;
-+
-+ return NULL;
-+}
-+
-+void __DWC_DMA_FREE(void *dma_ctx, uint32_t size, void *virt_addr, dwc_dma_t dma_addr)
-+{
-+ dwc_dmactx_t *dma = (dwc_dmactx_t *)dma_ctx;
-+
-+ if (dma->dma_map != NULL) {
-+ bus_dmamap_sync(dma->dma_tag, dma->dma_map, 0, size,
-+ BUS_DMASYNC_POSTREAD | BUS_DMASYNC_POSTWRITE);
-+ bus_dmamap_unload(dma->dma_tag, dma->dma_map);
-+ bus_dmamap_destroy(dma->dma_tag, dma->dma_map);
-+ bus_dmamem_unmap(dma->dma_tag, dma->dma_vaddr, size);
-+ bus_dmamem_free(dma->dma_tag, dma->segs, dma->nsegs);
-+ dma->dma_paddr = 0;
-+ dma->dma_map = NULL;
-+ dma->dma_vaddr = NULL;
-+ dma->nsegs = 0;
-+ }
-+}
-+
-+void *__DWC_ALLOC(void *mem_ctx, uint32_t size)
-+{
-+ return malloc(size, M_DEVBUF, M_WAITOK | M_ZERO);
-+}
-+
-+void *__DWC_ALLOC_ATOMIC(void *mem_ctx, uint32_t size)
-+{
-+ return malloc(size, M_DEVBUF, M_NOWAIT | M_ZERO);
-+}
-+
-+void __DWC_FREE(void *mem_ctx, void *addr)
-+{
-+ free(addr, M_DEVBUF);
-+}
-+
-+
-+#ifdef DWC_CRYPTOLIB
-+/* dwc_crypto.h */
-+
-+void DWC_RANDOM_BYTES(uint8_t *buffer, uint32_t length)
-+{
-+ get_random_bytes(buffer, length);
-+}
-+
-+int DWC_AES_CBC(uint8_t *message, uint32_t messagelen, uint8_t *key, uint32_t keylen, uint8_t iv[16], uint8_t *out)
-+{
-+ struct crypto_blkcipher *tfm;
-+ struct blkcipher_desc desc;
-+ struct scatterlist sgd;
-+ struct scatterlist sgs;
-+
-+ tfm = crypto_alloc_blkcipher("cbc(aes)", 0, CRYPTO_ALG_ASYNC);
-+ if (tfm == NULL) {
-+ printk("failed to load transform for aes CBC\n");
-+ return -1;
-+ }
-+
-+ crypto_blkcipher_setkey(tfm, key, keylen);
-+ crypto_blkcipher_set_iv(tfm, iv, 16);
-+
-+ sg_init_one(&sgd, out, messagelen);
-+ sg_init_one(&sgs, message, messagelen);
-+
-+ desc.tfm = tfm;
-+ desc.flags = 0;
-+
-+ if (crypto_blkcipher_encrypt(&desc, &sgd, &sgs, messagelen)) {
-+ crypto_free_blkcipher(tfm);
-+ DWC_ERROR("AES CBC encryption failed");
-+ return -1;
-+ }
-+
-+ crypto_free_blkcipher(tfm);
-+ return 0;
-+}
-+
-+int DWC_SHA256(uint8_t *message, uint32_t len, uint8_t *out)
-+{
-+ struct crypto_hash *tfm;
-+ struct hash_desc desc;
-+ struct scatterlist sg;
-+
-+ tfm = crypto_alloc_hash("sha256", 0, CRYPTO_ALG_ASYNC);
-+ if (IS_ERR(tfm)) {
-+ DWC_ERROR("Failed to load transform for sha256: %ld", PTR_ERR(tfm));
-+ return 0;
-+ }
-+ desc.tfm = tfm;
-+ desc.flags = 0;
-+
-+ sg_init_one(&sg, message, len);
-+ crypto_hash_digest(&desc, &sg, len, out);
-+ crypto_free_hash(tfm);
-+
-+ return 1;
-+}
-+
-+int DWC_HMAC_SHA256(uint8_t *message, uint32_t messagelen,
-+ uint8_t *key, uint32_t keylen, uint8_t *out)
-+{
-+ struct crypto_hash *tfm;
-+ struct hash_desc desc;
-+ struct scatterlist sg;
-+
-+ tfm = crypto_alloc_hash("hmac(sha256)", 0, CRYPTO_ALG_ASYNC);
-+ if (IS_ERR(tfm)) {
-+ DWC_ERROR("Failed to load transform for hmac(sha256): %ld", PTR_ERR(tfm));
-+ return 0;
-+ }
-+ desc.tfm = tfm;
-+ desc.flags = 0;
-+
-+ sg_init_one(&sg, message, messagelen);
-+ crypto_hash_setkey(tfm, key, keylen);
-+ crypto_hash_digest(&desc, &sg, messagelen, out);
-+ crypto_free_hash(tfm);
-+
-+ return 1;
-+}
-+
-+#endif /* DWC_CRYPTOLIB */
-+
-+
-+/* Byte Ordering Conversions */
-+
-+uint32_t DWC_CPU_TO_LE32(uint32_t *p)
-+{
-+#ifdef __LITTLE_ENDIAN
-+ return *p;
-+#else
-+ uint8_t *u_p = (uint8_t *)p;
-+
-+ return (u_p[3] | (u_p[2] << 8) | (u_p[1] << 16) | (u_p[0] << 24));
-+#endif
-+}
-+
-+uint32_t DWC_CPU_TO_BE32(uint32_t *p)
-+{
-+#ifdef __BIG_ENDIAN
-+ return *p;
-+#else
-+ uint8_t *u_p = (uint8_t *)p;
-+
-+ return (u_p[3] | (u_p[2] << 8) | (u_p[1] << 16) | (u_p[0] << 24));
-+#endif
-+}
-+
-+uint32_t DWC_LE32_TO_CPU(uint32_t *p)
-+{
-+#ifdef __LITTLE_ENDIAN
-+ return *p;
-+#else
-+ uint8_t *u_p = (uint8_t *)p;
-+
-+ return (u_p[3] | (u_p[2] << 8) | (u_p[1] << 16) | (u_p[0] << 24));
-+#endif
-+}
-+
-+uint32_t DWC_BE32_TO_CPU(uint32_t *p)
-+{
-+#ifdef __BIG_ENDIAN
-+ return *p;
-+#else
-+ uint8_t *u_p = (uint8_t *)p;
-+
-+ return (u_p[3] | (u_p[2] << 8) | (u_p[1] << 16) | (u_p[0] << 24));
-+#endif
-+}
-+
-+uint16_t DWC_CPU_TO_LE16(uint16_t *p)
-+{
-+#ifdef __LITTLE_ENDIAN
-+ return *p;
-+#else
-+ uint8_t *u_p = (uint8_t *)p;
-+ return (u_p[1] | (u_p[0] << 8));
-+#endif
-+}
-+
-+uint16_t DWC_CPU_TO_BE16(uint16_t *p)
-+{
-+#ifdef __BIG_ENDIAN
-+ return *p;
-+#else
-+ uint8_t *u_p = (uint8_t *)p;
-+ return (u_p[1] | (u_p[0] << 8));
-+#endif
-+}
-+
-+uint16_t DWC_LE16_TO_CPU(uint16_t *p)
-+{
-+#ifdef __LITTLE_ENDIAN
-+ return *p;
-+#else
-+ uint8_t *u_p = (uint8_t *)p;
-+ return (u_p[1] | (u_p[0] << 8));
-+#endif
-+}
-+
-+uint16_t DWC_BE16_TO_CPU(uint16_t *p)
-+{
-+#ifdef __BIG_ENDIAN
-+ return *p;
-+#else
-+ uint8_t *u_p = (uint8_t *)p;
-+ return (u_p[1] | (u_p[0] << 8));
-+#endif
-+}
-+
-+
-+/* Registers */
-+
-+uint32_t DWC_READ_REG32(void *io_ctx, uint32_t volatile *reg)
-+{
-+ dwc_ioctx_t *io = (dwc_ioctx_t *)io_ctx;
-+ bus_size_t ior = (bus_size_t)reg;
-+
-+ return bus_space_read_4(io->iot, io->ioh, ior);
-+}
-+
-+#if 0
-+uint64_t DWC_READ_REG64(void *io_ctx, uint64_t volatile *reg)
-+{
-+ dwc_ioctx_t *io = (dwc_ioctx_t *)io_ctx;
-+ bus_size_t ior = (bus_size_t)reg;
-+
-+ return bus_space_read_8(io->iot, io->ioh, ior);
-+}
-+#endif
-+
-+void DWC_WRITE_REG32(void *io_ctx, uint32_t volatile *reg, uint32_t value)
-+{
-+ dwc_ioctx_t *io = (dwc_ioctx_t *)io_ctx;
-+ bus_size_t ior = (bus_size_t)reg;
-+
-+ bus_space_write_4(io->iot, io->ioh, ior, value);
-+}
-+
-+#if 0
-+void DWC_WRITE_REG64(void *io_ctx, uint64_t volatile *reg, uint64_t value)
-+{
-+ dwc_ioctx_t *io = (dwc_ioctx_t *)io_ctx;
-+ bus_size_t ior = (bus_size_t)reg;
-+
-+ bus_space_write_8(io->iot, io->ioh, ior, value);
-+}
-+#endif
-+
-+void DWC_MODIFY_REG32(void *io_ctx, uint32_t volatile *reg, uint32_t clear_mask,
-+ uint32_t set_mask)
-+{
-+ dwc_ioctx_t *io = (dwc_ioctx_t *)io_ctx;
-+ bus_size_t ior = (bus_size_t)reg;
-+
-+ bus_space_write_4(io->iot, io->ioh, ior,
-+ (bus_space_read_4(io->iot, io->ioh, ior) &
-+ ~clear_mask) | set_mask);
-+}
-+
-+#if 0
-+void DWC_MODIFY_REG64(void *io_ctx, uint64_t volatile *reg, uint64_t clear_mask,
-+ uint64_t set_mask)
-+{
-+ dwc_ioctx_t *io = (dwc_ioctx_t *)io_ctx;
-+ bus_size_t ior = (bus_size_t)reg;
-+
-+ bus_space_write_8(io->iot, io->ioh, ior,
-+ (bus_space_read_8(io->iot, io->ioh, ior) &
-+ ~clear_mask) | set_mask);
-+}
-+#endif
-+
-+
-+/* Locking */
-+
-+dwc_spinlock_t *DWC_SPINLOCK_ALLOC(void)
-+{
-+ struct simplelock *sl = DWC_ALLOC(sizeof(*sl));
-+
-+ if (!sl) {
-+ DWC_ERROR("Cannot allocate memory for spinlock");
-+ return NULL;
-+ }
-+
-+ simple_lock_init(sl);
-+ return (dwc_spinlock_t *)sl;
-+}
-+
-+void DWC_SPINLOCK_FREE(dwc_spinlock_t *lock)
-+{
-+ struct simplelock *sl = (struct simplelock *)lock;
-+
-+ DWC_FREE(sl);
-+}
-+
-+void DWC_SPINLOCK(dwc_spinlock_t *lock)
-+{
-+ simple_lock((struct simplelock *)lock);
-+}
-+
-+void DWC_SPINUNLOCK(dwc_spinlock_t *lock)
-+{
-+ simple_unlock((struct simplelock *)lock);
-+}
-+
-+void DWC_SPINLOCK_IRQSAVE(dwc_spinlock_t *lock, dwc_irqflags_t *flags)
-+{
-+ simple_lock((struct simplelock *)lock);
-+ *flags = splbio();
-+}
-+
-+void DWC_SPINUNLOCK_IRQRESTORE(dwc_spinlock_t *lock, dwc_irqflags_t flags)
-+{
-+ splx(flags);
-+ simple_unlock((struct simplelock *)lock);
-+}
-+
-+dwc_mutex_t *DWC_MUTEX_ALLOC(void)
-+{
-+ dwc_mutex_t *mutex = DWC_ALLOC(sizeof(struct lock));
-+
-+ if (!mutex) {
-+ DWC_ERROR("Cannot allocate memory for mutex");
-+ return NULL;
-+ }
-+
-+ lockinit((struct lock *)mutex, 0, "dw3mtx", 0, 0);
-+ return mutex;
-+}
-+
-+#if (defined(DWC_LINUX) && defined(CONFIG_DEBUG_MUTEXES))
-+#else
-+void DWC_MUTEX_FREE(dwc_mutex_t *mutex)
-+{
-+ DWC_FREE(mutex);
-+}
-+#endif
-+
-+void DWC_MUTEX_LOCK(dwc_mutex_t *mutex)
-+{
-+ lockmgr((struct lock *)mutex, LK_EXCLUSIVE, NULL);
-+}
-+
-+int DWC_MUTEX_TRYLOCK(dwc_mutex_t *mutex)
-+{
-+ int status;
-+
-+ status = lockmgr((struct lock *)mutex, LK_EXCLUSIVE | LK_NOWAIT, NULL);
-+ return status == 0;
-+}
-+
-+void DWC_MUTEX_UNLOCK(dwc_mutex_t *mutex)
-+{
-+ lockmgr((struct lock *)mutex, LK_RELEASE, NULL);
-+}
-+
-+
-+/* Timing */
-+
-+void DWC_UDELAY(uint32_t usecs)
-+{
-+ DELAY(usecs);
-+}
-+
-+void DWC_MDELAY(uint32_t msecs)
-+{
-+ do {
-+ DELAY(1000);
-+ } while (--msecs);
-+}
-+
-+void DWC_MSLEEP(uint32_t msecs)
-+{
-+ struct timeval tv;
-+
-+ tv.tv_sec = msecs / 1000;
-+ tv.tv_usec = (msecs - tv.tv_sec * 1000) * 1000;
-+ tsleep(&tv, 0, "dw3slp", tvtohz(&tv));
-+}
-+
-+uint32_t DWC_TIME(void)
-+{
-+ struct timeval tv;
-+
-+ microuptime(&tv); // or getmicrouptime? (less precise, but faster)
-+ return tv.tv_sec * 1000 + tv.tv_usec / 1000;
-+}
-+
-+
-+/* Timers */
-+
-+struct dwc_timer {
-+ struct callout t;
-+ char *name;
-+ dwc_spinlock_t *lock;
-+ dwc_timer_callback_t cb;
-+ void *data;
-+};
-+
-+dwc_timer_t *DWC_TIMER_ALLOC(char *name, dwc_timer_callback_t cb, void *data)
-+{
-+ dwc_timer_t *t = DWC_ALLOC(sizeof(*t));
-+
-+ if (!t) {
-+ DWC_ERROR("Cannot allocate memory for timer");
-+ return NULL;
-+ }
-+
-+ callout_init(&t->t);
-+
-+ t->name = DWC_STRDUP(name);
-+ if (!t->name) {
-+ DWC_ERROR("Cannot allocate memory for timer->name");
-+ goto no_name;
-+ }
-+
-+ t->lock = DWC_SPINLOCK_ALLOC();
-+ if (!t->lock) {
-+ DWC_ERROR("Cannot allocate memory for timer->lock");
-+ goto no_lock;
-+ }
-+
-+ t->cb = cb;
-+ t->data = data;
-+
-+ return t;
-+
-+ no_lock:
-+ DWC_FREE(t->name);
-+ no_name:
-+ DWC_FREE(t);
-+
-+ return NULL;
-+}
-+
-+void DWC_TIMER_FREE(dwc_timer_t *timer)
-+{
-+ callout_stop(&timer->t);
-+ DWC_SPINLOCK_FREE(timer->lock);
-+ DWC_FREE(timer->name);
-+ DWC_FREE(timer);
-+}
-+
-+void DWC_TIMER_SCHEDULE(dwc_timer_t *timer, uint32_t time)
-+{
-+ struct timeval tv;
-+
-+ tv.tv_sec = time / 1000;
-+ tv.tv_usec = (time - tv.tv_sec * 1000) * 1000;
-+ callout_reset(&timer->t, tvtohz(&tv), timer->cb, timer->data);
-+}
-+
-+void DWC_TIMER_CANCEL(dwc_timer_t *timer)
-+{
-+ callout_stop(&timer->t);
-+}
-+
-+
-+/* Wait Queues */
-+
-+struct dwc_waitq {
-+ struct simplelock lock;
-+ int abort;
-+};
-+
-+dwc_waitq_t *DWC_WAITQ_ALLOC(void)
-+{
-+ dwc_waitq_t *wq = DWC_ALLOC(sizeof(*wq));
-+
-+ if (!wq) {
-+ DWC_ERROR("Cannot allocate memory for waitqueue");
-+ return NULL;
-+ }
-+
-+ simple_lock_init(&wq->lock);
-+ wq->abort = 0;
-+
-+ return wq;
-+}
-+
-+void DWC_WAITQ_FREE(dwc_waitq_t *wq)
-+{
-+ DWC_FREE(wq);
-+}
-+
-+int32_t DWC_WAITQ_WAIT(dwc_waitq_t *wq, dwc_waitq_condition_t cond, void *data)
-+{
-+ int ipl;
-+ int result = 0;
-+
-+ simple_lock(&wq->lock);
-+ ipl = splbio();
-+
-+ /* Skip the sleep if already aborted or triggered */
-+ if (!wq->abort && !cond(data)) {
-+ splx(ipl);
-+ result = ltsleep(wq, PCATCH, "dw3wat", 0, &wq->lock); // infinite timeout
-+ ipl = splbio();
-+ }
-+
-+ if (result == 0) { // awoken
-+ if (wq->abort) {
-+ wq->abort = 0;
-+ result = -DWC_E_ABORT;
-+ } else {
-+ result = 0;
-+ }
-+
-+ splx(ipl);
-+ simple_unlock(&wq->lock);
-+ } else {
-+ wq->abort = 0;
-+ splx(ipl);
-+ simple_unlock(&wq->lock);
-+
-+ if (result == ERESTART) { // signaled - restart
-+ result = -DWC_E_RESTART;
-+ } else { // signaled - must be EINTR
-+ result = -DWC_E_ABORT;
-+ }
-+ }
-+
-+ return result;
-+}
-+
-+int32_t DWC_WAITQ_WAIT_TIMEOUT(dwc_waitq_t *wq, dwc_waitq_condition_t cond,
-+ void *data, int32_t msecs)
-+{
-+ struct timeval tv, tv1, tv2;
-+ int ipl;
-+ int result = 0;
-+
-+ tv.tv_sec = msecs / 1000;
-+ tv.tv_usec = (msecs - tv.tv_sec * 1000) * 1000;
-+
-+ simple_lock(&wq->lock);
-+ ipl = splbio();
-+
-+ /* Skip the sleep if already aborted or triggered */
-+ if (!wq->abort && !cond(data)) {
-+ splx(ipl);
-+ getmicrouptime(&tv1);
-+ result = ltsleep(wq, PCATCH, "dw3wto", tvtohz(&tv), &wq->lock);
-+ getmicrouptime(&tv2);
-+ ipl = splbio();
-+ }
-+
-+ if (result == 0) { // awoken
-+ if (wq->abort) {
-+ wq->abort = 0;
-+ splx(ipl);
-+ simple_unlock(&wq->lock);
-+ result = -DWC_E_ABORT;
-+ } else {
-+ splx(ipl);
-+ simple_unlock(&wq->lock);
-+
-+ tv2.tv_usec -= tv1.tv_usec;
-+ if (tv2.tv_usec < 0) {
-+ tv2.tv_usec += 1000000;
-+ tv2.tv_sec--;
-+ }
-+
-+ tv2.tv_sec -= tv1.tv_sec;
-+ result = tv2.tv_sec * 1000 + tv2.tv_usec / 1000;
-+ result = msecs - result;
-+ if (result <= 0)
-+ result = 1;
-+ }
-+ } else {
-+ wq->abort = 0;
-+ splx(ipl);
-+ simple_unlock(&wq->lock);
-+
-+ if (result == ERESTART) { // signaled - restart
-+ result = -DWC_E_RESTART;
-+
-+ } else if (result == EINTR) { // signaled - interrupt
-+ result = -DWC_E_ABORT;
-+
-+ } else { // timed out
-+ result = -DWC_E_TIMEOUT;
-+ }
-+ }
-+
-+ return result;
-+}
-+
-+void DWC_WAITQ_TRIGGER(dwc_waitq_t *wq)
-+{
-+ wakeup(wq);
-+}
-+
-+void DWC_WAITQ_ABORT(dwc_waitq_t *wq)
-+{
-+ int ipl;
-+
-+ simple_lock(&wq->lock);
-+ ipl = splbio();
-+ wq->abort = 1;
-+ wakeup(wq);
-+ splx(ipl);
-+ simple_unlock(&wq->lock);
-+}
-+
-+
-+/* Threading */
-+
-+struct dwc_thread {
-+ struct proc *proc;
-+ int abort;
-+};
-+
-+dwc_thread_t *DWC_THREAD_RUN(dwc_thread_function_t func, char *name, void *data)
-+{
-+ int retval;
-+ dwc_thread_t *thread = DWC_ALLOC(sizeof(*thread));
-+
-+ if (!thread) {
-+ return NULL;
-+ }
-+
-+ thread->abort = 0;
-+ retval = kthread_create1((void (*)(void *))func, data, &thread->proc,
-+ "%s", name);
-+ if (retval) {
-+ DWC_FREE(thread);
-+ return NULL;
-+ }
-+
-+ return thread;
-+}
-+
-+int DWC_THREAD_STOP(dwc_thread_t *thread)
-+{
-+ int retval;
-+
-+ thread->abort = 1;
-+ retval = tsleep(&thread->abort, 0, "dw3stp", 60 * hz);
-+
-+ if (retval == 0) {
-+ /* DWC_THREAD_EXIT() will free the thread struct */
-+ return 0;
-+ }
-+
-+ /* NOTE: We leak the thread struct if thread doesn't die */
-+
-+ if (retval == EWOULDBLOCK) {
-+ return -DWC_E_TIMEOUT;
-+ }
-+
-+ return -DWC_E_UNKNOWN;
-+}
-+
-+dwc_bool_t DWC_THREAD_SHOULD_STOP(dwc_thread_t *thread)
-+{
-+ return thread->abort;
-+}
-+
-+void DWC_THREAD_EXIT(dwc_thread_t *thread)
-+{
-+ wakeup(&thread->abort);
-+ DWC_FREE(thread);
-+ kthread_exit(0);
-+}
-+
-+/* tasklets
-+ - Runs in interrupt context (cannot sleep)
-+ - Each tasklet runs on a single CPU
-+ - Different tasklets can be running simultaneously on different CPUs
-+ [ On NetBSD there is no corresponding mechanism, drivers don't have bottom-
-+ halves. So we just call the callback directly from DWC_TASK_SCHEDULE() ]
-+ */
-+struct dwc_tasklet {
-+ dwc_tasklet_callback_t cb;
-+ void *data;
-+};
-+
-+static void tasklet_callback(void *data)
-+{
-+ dwc_tasklet_t *task = (dwc_tasklet_t *)data;
-+
-+ task->cb(task->data);
-+}
-+
-+dwc_tasklet_t *DWC_TASK_ALLOC(char *name, dwc_tasklet_callback_t cb, void *data)
-+{
-+ dwc_tasklet_t *task = DWC_ALLOC(sizeof(*task));
-+
-+ if (task) {
-+ task->cb = cb;
-+ task->data = data;
-+ } else {
-+ DWC_ERROR("Cannot allocate memory for tasklet");
-+ }
-+
-+ return task;
-+}
-+
-+void DWC_TASK_FREE(dwc_tasklet_t *task)
-+{
-+ DWC_FREE(task);
-+}
-+
-+void DWC_TASK_SCHEDULE(dwc_tasklet_t *task)
-+{
-+ tasklet_callback(task);
-+}
-+
-+
-+/* workqueues
-+ - Runs in process context (can sleep)
-+ */
-+typedef struct work_container {
-+ dwc_work_callback_t cb;
-+ void *data;
-+ dwc_workq_t *wq;
-+ char *name;
-+ int hz;
-+ struct work task;
-+} work_container_t;
-+
-+struct dwc_workq {
-+ struct workqueue *taskq;
-+ dwc_spinlock_t *lock;
-+ dwc_waitq_t *waitq;
-+ int pending;
-+ struct work_container *container;
-+};
-+
-+static void do_work(struct work *task, void *data)
-+{
-+ dwc_workq_t *wq = (dwc_workq_t *)data;
-+ work_container_t *container = wq->container;
-+ dwc_irqflags_t flags;
-+
-+ if (container->hz) {
-+ tsleep(container, 0, "dw3wrk", container->hz);
-+ }
-+
-+ container->cb(container->data);
-+ DWC_DEBUG("Work done: %s, container=%p", container->name, container);
-+
-+ DWC_SPINLOCK_IRQSAVE(wq->lock, &flags);
-+ if (container->name)
-+ DWC_FREE(container->name);
-+ DWC_FREE(container);
-+ wq->pending--;
-+ DWC_SPINUNLOCK_IRQRESTORE(wq->lock, flags);
-+ DWC_WAITQ_TRIGGER(wq->waitq);
-+}
-+
-+static int work_done(void *data)
-+{
-+ dwc_workq_t *workq = (dwc_workq_t *)data;
-+
-+ return workq->pending == 0;
-+}
-+
-+int DWC_WORKQ_WAIT_WORK_DONE(dwc_workq_t *workq, int timeout)
-+{
-+ return DWC_WAITQ_WAIT_TIMEOUT(workq->waitq, work_done, workq, timeout);
-+}
-+
-+dwc_workq_t *DWC_WORKQ_ALLOC(char *name)
-+{
-+ int result;
-+ dwc_workq_t *wq = DWC_ALLOC(sizeof(*wq));
-+
-+ if (!wq) {
-+ DWC_ERROR("Cannot allocate memory for workqueue");
-+ return NULL;
-+ }
-+
-+ result = workqueue_create(&wq->taskq, name, do_work, wq, 0 /*PWAIT*/,
-+ IPL_BIO, 0);
-+ if (result) {
-+ DWC_ERROR("Cannot create workqueue");
-+ goto no_taskq;
-+ }
-+
-+ wq->pending = 0;
-+
-+ wq->lock = DWC_SPINLOCK_ALLOC();
-+ if (!wq->lock) {
-+ DWC_ERROR("Cannot allocate memory for spinlock");
-+ goto no_lock;
-+ }
-+
-+ wq->waitq = DWC_WAITQ_ALLOC();
-+ if (!wq->waitq) {
-+ DWC_ERROR("Cannot allocate memory for waitqueue");
-+ goto no_waitq;
-+ }
-+
-+ return wq;
-+
-+ no_waitq:
-+ DWC_SPINLOCK_FREE(wq->lock);
-+ no_lock:
-+ workqueue_destroy(wq->taskq);
-+ no_taskq:
-+ DWC_FREE(wq);
-+
-+ return NULL;
-+}
-+
-+void DWC_WORKQ_FREE(dwc_workq_t *wq)
-+{
-+#ifdef DEBUG
-+ dwc_irqflags_t flags;
-+
-+ DWC_SPINLOCK_IRQSAVE(wq->lock, &flags);
-+
-+ if (wq->pending != 0) {
-+ struct work_container *container = wq->container;
-+
-+ DWC_ERROR("Destroying work queue with pending work");
-+
-+ if (container && container->name) {
-+ DWC_ERROR("Work %s still pending", container->name);
-+ }
-+ }
-+
-+ DWC_SPINUNLOCK_IRQRESTORE(wq->lock, flags);
-+#endif
-+ DWC_WAITQ_FREE(wq->waitq);
-+ DWC_SPINLOCK_FREE(wq->lock);
-+ workqueue_destroy(wq->taskq);
-+ DWC_FREE(wq);
-+}
-+
-+void DWC_WORKQ_SCHEDULE(dwc_workq_t *wq, dwc_work_callback_t cb, void *data,
-+ char *format, ...)
-+{
-+ dwc_irqflags_t flags;
-+ work_container_t *container;
-+ static char name[128];
-+ va_list args;
-+
-+ va_start(args, format);
-+ DWC_VSNPRINTF(name, 128, format, args);
-+ va_end(args);
-+
-+ DWC_SPINLOCK_IRQSAVE(wq->lock, &flags);
-+ wq->pending++;
-+ DWC_SPINUNLOCK_IRQRESTORE(wq->lock, flags);
-+ DWC_WAITQ_TRIGGER(wq->waitq);
-+
-+ container = DWC_ALLOC_ATOMIC(sizeof(*container));
-+ if (!container) {
-+ DWC_ERROR("Cannot allocate memory for container");
-+ return;
-+ }
-+
-+ container->name = DWC_STRDUP(name);
-+ if (!container->name) {
-+ DWC_ERROR("Cannot allocate memory for container->name");
-+ DWC_FREE(container);
-+ return;
-+ }
-+
-+ container->cb = cb;
-+ container->data = data;
-+ container->wq = wq;
-+ container->hz = 0;
-+ wq->container = container;
-+
-+ DWC_DEBUG("Queueing work: %s, container=%p", container->name, container);
-+ workqueue_enqueue(wq->taskq, &container->task);
-+}
-+
-+void DWC_WORKQ_SCHEDULE_DELAYED(dwc_workq_t *wq, dwc_work_callback_t cb,
-+ void *data, uint32_t time, char *format, ...)
-+{
-+ dwc_irqflags_t flags;
-+ work_container_t *container;
-+ static char name[128];
-+ struct timeval tv;
-+ va_list args;
-+
-+ va_start(args, format);
-+ DWC_VSNPRINTF(name, 128, format, args);
-+ va_end(args);
-+
-+ DWC_SPINLOCK_IRQSAVE(wq->lock, &flags);
-+ wq->pending++;
-+ DWC_SPINUNLOCK_IRQRESTORE(wq->lock, flags);
-+ DWC_WAITQ_TRIGGER(wq->waitq);
-+
-+ container = DWC_ALLOC_ATOMIC(sizeof(*container));
-+ if (!container) {
-+ DWC_ERROR("Cannot allocate memory for container");
-+ return;
-+ }
-+
-+ container->name = DWC_STRDUP(name);
-+ if (!container->name) {
-+ DWC_ERROR("Cannot allocate memory for container->name");
-+ DWC_FREE(container);
-+ return;
-+ }
-+
-+ container->cb = cb;
-+ container->data = data;
-+ container->wq = wq;
-+ tv.tv_sec = time / 1000;
-+ tv.tv_usec = (time - tv.tv_sec * 1000) * 1000;
-+ container->hz = tvtohz(&tv);
-+ wq->container = container;
-+
-+ DWC_DEBUG("Queueing work: %s, container=%p", container->name, container);
-+ workqueue_enqueue(wq->taskq, &container->task);
-+}
-+
-+int DWC_WORKQ_PENDING(dwc_workq_t *wq)
-+{
-+ return wq->pending;
-+}
---- /dev/null
-+++ b/drivers/usb/host/dwc_common_port/dwc_crypto.c
-@@ -0,0 +1,308 @@
-+/* =========================================================================
-+ * $File: //dwh/usb_iip/dev/software/dwc_common_port_2/dwc_crypto.c $
-+ * $Revision: #5 $
-+ * $Date: 2010/09/28 $
-+ * $Change: 1596182 $
-+ *
-+ * Synopsys Portability Library Software and documentation
-+ * (hereinafter, "Software") is an Unsupported proprietary work of
-+ * Synopsys, Inc. unless otherwise expressly agreed to in writing
-+ * between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product
-+ * under any End User Software License Agreement or Agreement for
-+ * Licensed Product with Synopsys or any supplement thereto. You are
-+ * permitted to use and redistribute this Software in source and binary
-+ * forms, with or without modification, provided that redistributions
-+ * of source code must retain this notice. You may not view, use,
-+ * disclose, copy or distribute this file or any information contained
-+ * herein except pursuant to this license grant from Synopsys. If you
-+ * do not agree with this notice, including the disclaimer below, then
-+ * you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS"
-+ * BASIS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
-+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
-+ * FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. IN NO EVENT SHALL
-+ * SYNOPSYS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY
-+ * OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
-+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
-+ * USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================= */
-+
-+/** @file
-+ * This file contains the WUSB cryptographic routines.
-+ */
-+
-+#ifdef DWC_CRYPTOLIB
-+
-+#include "dwc_crypto.h"
-+#include "usb.h"
-+
-+#ifdef DEBUG
-+static inline void dump_bytes(char *name, uint8_t *bytes, int len)
-+{
-+ int i;
-+ DWC_PRINTF("%s: ", name);
-+ for (i=0; i<len; i++) {
-+ DWC_PRINTF("%02x ", bytes[i]);
-+ }
-+ DWC_PRINTF("\n");
-+}
-+#else
-+#define dump_bytes(x...)
-+#endif
-+
-+/* Display a block */
-+void show_block(const u8 *blk, const char *prefix, const char *suffix, int a)
-+{
-+#ifdef DWC_DEBUG_CRYPTO
-+ int i, blksize = 16;
-+
-+ DWC_DEBUG("%s", prefix);
-+
-+ if (suffix == NULL) {
-+ suffix = "\n";
-+ blksize = a;
-+ }
-+
-+ for (i = 0; i < blksize; i++)
-+ DWC_PRINT("%02x%s", *blk++, ((i & 3) == 3) ? " " : " ");
-+ DWC_PRINT(suffix);
-+#endif
-+}
-+
-+/**
-+ * Encrypts an array of bytes using the AES encryption engine.
-+ * If <code>dst</code> == <code>src</code>, then the bytes will be encrypted
-+ * in-place.
-+ *
-+ * @return 0 on success, negative error code on error.
-+ */
-+int dwc_wusb_aes_encrypt(u8 *src, u8 *key, u8 *dst)
-+{
-+ u8 block_t[16];
-+ DWC_MEMSET(block_t, 0, 16);
-+
-+ return DWC_AES_CBC(src, 16, key, 16, block_t, dst);
-+}
-+
-+/**
-+ * The CCM-MAC-FUNCTION described in section 6.5 of the WUSB spec.
-+ * This function takes a data string and returns the encrypted CBC
-+ * Counter-mode MIC.
-+ *
-+ * @param key The 128-bit symmetric key.
-+ * @param nonce The CCM nonce.
-+ * @param label The unique 14-byte ASCII text label.
-+ * @param bytes The byte array to be encrypted.
-+ * @param len Length of the byte array.
-+ * @param result Byte array to receive the 8-byte encrypted MIC.
-+ */
-+void dwc_wusb_cmf(u8 *key, u8 *nonce,
-+ char *label, u8 *bytes, int len, u8 *result)
-+{
-+ u8 block_m[16];
-+ u8 block_x[16];
-+ u8 block_t[8];
-+ int idx, blkNum;
-+ u16 la = (u16)(len + 14);
-+
-+ /* Set the AES-128 key */
-+ //dwc_aes_setkey(tfm, key, 16);
-+
-+ /* Fill block B0 from flags = 0x59, N, and l(m) = 0 */
-+ block_m[0] = 0x59;
-+ for (idx = 0; idx < 13; idx++)
-+ block_m[idx + 1] = nonce[idx];
-+ block_m[14] = 0;
-+ block_m[15] = 0;
-+
-+ /* Produce the CBC IV */
-+ dwc_wusb_aes_encrypt(block_m, key, block_x);
-+ show_block(block_m, "CBC IV in: ", "\n", 0);
-+ show_block(block_x, "CBC IV out:", "\n", 0);
-+
-+ /* Fill block B1 from l(a) = Blen + 14, and A */
-+ block_x[0] ^= (u8)(la >> 8);
-+ block_x[1] ^= (u8)la;
-+ for (idx = 0; idx < 14; idx++)
-+ block_x[idx + 2] ^= label[idx];
-+ show_block(block_x, "After xor: ", "b1\n", 16);
-+
-+ dwc_wusb_aes_encrypt(block_x, key, block_x);
-+ show_block(block_x, "After AES: ", "b1\n", 16);
-+
-+ idx = 0;
-+ blkNum = 0;
-+
-+ /* Fill remaining blocks with B */
-+ while (len-- > 0) {
-+ block_x[idx] ^= *bytes++;
-+ if (++idx >= 16) {
-+ idx = 0;
-+ show_block(block_x, "After xor: ", "\n", blkNum);
-+ dwc_wusb_aes_encrypt(block_x, key, block_x);
-+ show_block(block_x, "After AES: ", "\n", blkNum);
-+ blkNum++;
-+ }
-+ }
-+
-+ /* Handle partial last block */
-+ if (idx > 0) {
-+ show_block(block_x, "After xor: ", "\n", blkNum);
-+ dwc_wusb_aes_encrypt(block_x, key, block_x);
-+ show_block(block_x, "After AES: ", "\n", blkNum);
-+ }
-+
-+ /* Save the MIC tag */
-+ DWC_MEMCPY(block_t, block_x, 8);
-+ show_block(block_t, "MIC tag : ", NULL, 8);
-+
-+ /* Fill block A0 from flags = 0x01, N, and counter = 0 */
-+ block_m[0] = 0x01;
-+ block_m[14] = 0;
-+ block_m[15] = 0;
-+
-+ /* Encrypt the counter */
-+ dwc_wusb_aes_encrypt(block_m, key, block_x);
-+ show_block(block_x, "CTR[MIC] : ", NULL, 8);
-+
-+ /* XOR with MIC tag */
-+ for (idx = 0; idx < 8; idx++) {
-+ block_t[idx] ^= block_x[idx];
-+ }
-+
-+ /* Return result to caller */
-+ DWC_MEMCPY(result, block_t, 8);
-+ show_block(result, "CCM-MIC : ", NULL, 8);
-+
-+}
-+
-+/**
-+ * The PRF function described in section 6.5 of the WUSB spec. This function
-+ * concatenates MIC values returned from dwc_cmf() to create a value of
-+ * the requested length.
-+ *
-+ * @param prf_len Length of the PRF function in bits (64, 128, or 256).
-+ * @param key, nonce, label, bytes, len Same as for dwc_cmf().
-+ * @param result Byte array to receive the result.
-+ */
-+void dwc_wusb_prf(int prf_len, u8 *key,
-+ u8 *nonce, char *label, u8 *bytes, int len, u8 *result)
-+{
-+ int i;
-+
-+ nonce[0] = 0;
-+ for (i = 0; i < prf_len >> 6; i++, nonce[0]++) {
-+ dwc_wusb_cmf(key, nonce, label, bytes, len, result);
-+ result += 8;
-+ }
-+}
-+
-+/**
-+ * Fills in CCM Nonce per the WUSB spec.
-+ *
-+ * @param[in] haddr Host address.
-+ * @param[in] daddr Device address.
-+ * @param[in] tkid Session Key(PTK) identifier.
-+ * @param[out] nonce Pointer to where the CCM Nonce output is to be written.
-+ */
-+void dwc_wusb_fill_ccm_nonce(uint16_t haddr, uint16_t daddr, uint8_t *tkid,
-+ uint8_t *nonce)
-+{
-+
-+ DWC_DEBUG("%s %x %x\n", __func__, daddr, haddr);
-+
-+ DWC_MEMSET(&nonce[0], 0, 16);
-+
-+ DWC_MEMCPY(&nonce[6], tkid, 3);
-+ nonce[9] = daddr & 0xFF;
-+ nonce[10] = (daddr >> 8) & 0xFF;
-+ nonce[11] = haddr & 0xFF;
-+ nonce[12] = (haddr >> 8) & 0xFF;
-+
-+ dump_bytes("CCM nonce", nonce, 16);
-+}
-+
-+/**
-+ * Generates a 16-byte cryptographic-grade random number for the Host/Device
-+ * Nonce.
-+ */
-+void dwc_wusb_gen_nonce(uint16_t addr, uint8_t *nonce)
-+{
-+ uint8_t inonce[16];
-+ uint32_t temp[4];
-+
-+ /* Fill in the Nonce */
-+ DWC_MEMSET(&inonce[0], 0, sizeof(inonce));
-+ inonce[9] = addr & 0xFF;
-+ inonce[10] = (addr >> 8) & 0xFF;
-+ inonce[11] = inonce[9];
-+ inonce[12] = inonce[10];
-+
-+ /* Collect "randomness samples" */
-+ DWC_RANDOM_BYTES((uint8_t *)temp, 16);
-+
-+ dwc_wusb_prf_128((uint8_t *)temp, nonce,
-+ "Random Numbers", (uint8_t *)temp, sizeof(temp),
-+ nonce);
-+}
-+
-+/**
-+ * Generates the Session Key (PTK) and Key Confirmation Key (KCK) per the
-+ * WUSB spec.
-+ *
-+ * @param[in] ccm_nonce Pointer to CCM Nonce.
-+ * @param[in] mk Master Key to derive the session from
-+ * @param[in] hnonce Pointer to Host Nonce.
-+ * @param[in] dnonce Pointer to Device Nonce.
-+ * @param[out] kck Pointer to where the KCK output is to be written.
-+ * @param[out] ptk Pointer to where the PTK output is to be written.
-+ */
-+void dwc_wusb_gen_key(uint8_t *ccm_nonce, uint8_t *mk, uint8_t *hnonce,
-+ uint8_t *dnonce, uint8_t *kck, uint8_t *ptk)
-+{
-+ uint8_t idata[32];
-+ uint8_t odata[32];
-+
-+ dump_bytes("ck", mk, 16);
-+ dump_bytes("hnonce", hnonce, 16);
-+ dump_bytes("dnonce", dnonce, 16);
-+
-+ /* The data is the HNonce and DNonce concatenated */
-+ DWC_MEMCPY(&idata[0], hnonce, 16);
-+ DWC_MEMCPY(&idata[16], dnonce, 16);
-+
-+ dwc_wusb_prf_256(mk, ccm_nonce, "Pair-wise keys", idata, 32, odata);
-+
-+ /* Low 16 bytes of the result is the KCK, high 16 is the PTK */
-+ DWC_MEMCPY(kck, &odata[0], 16);
-+ DWC_MEMCPY(ptk, &odata[16], 16);
-+
-+ dump_bytes("kck", kck, 16);
-+ dump_bytes("ptk", ptk, 16);
-+}
-+
-+/**
-+ * Generates the Message Integrity Code over the Handshake data per the
-+ * WUSB spec.
-+ *
-+ * @param ccm_nonce Pointer to CCM Nonce.
-+ * @param kck Pointer to Key Confirmation Key.
-+ * @param data Pointer to Handshake data to be checked.
-+ * @param mic Pointer to where the MIC output is to be written.
-+ */
-+void dwc_wusb_gen_mic(uint8_t *ccm_nonce, uint8_t *kck,
-+ uint8_t *data, uint8_t *mic)
-+{
-+
-+ dwc_wusb_prf_64(kck, ccm_nonce, "out-of-bandMIC",
-+ data, WUSB_HANDSHAKE_LEN_FOR_MIC, mic);
-+}
-+
-+#endif /* DWC_CRYPTOLIB */
---- /dev/null
-+++ b/drivers/usb/host/dwc_common_port/dwc_crypto.h
-@@ -0,0 +1,111 @@
-+/* =========================================================================
-+ * $File: //dwh/usb_iip/dev/software/dwc_common_port_2/dwc_crypto.h $
-+ * $Revision: #3 $
-+ * $Date: 2010/09/28 $
-+ * $Change: 1596182 $
-+ *
-+ * Synopsys Portability Library Software and documentation
-+ * (hereinafter, "Software") is an Unsupported proprietary work of
-+ * Synopsys, Inc. unless otherwise expressly agreed to in writing
-+ * between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product
-+ * under any End User Software License Agreement or Agreement for
-+ * Licensed Product with Synopsys or any supplement thereto. You are
-+ * permitted to use and redistribute this Software in source and binary
-+ * forms, with or without modification, provided that redistributions
-+ * of source code must retain this notice. You may not view, use,
-+ * disclose, copy or distribute this file or any information contained
-+ * herein except pursuant to this license grant from Synopsys. If you
-+ * do not agree with this notice, including the disclaimer below, then
-+ * you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS"
-+ * BASIS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
-+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
-+ * FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. IN NO EVENT SHALL
-+ * SYNOPSYS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY
-+ * OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
-+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
-+ * USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================= */
-+
-+#ifndef _DWC_CRYPTO_H_
-+#define _DWC_CRYPTO_H_
-+
-+#ifdef __cplusplus
-+extern "C" {
-+#endif
-+
-+/** @file
-+ *
-+ * This file contains declarations for the WUSB Cryptographic routines as
-+ * defined in the WUSB spec. They are only to be used internally by the DWC UWB
-+ * modules.
-+ */
-+
-+#include "dwc_os.h"
-+
-+int dwc_wusb_aes_encrypt(u8 *src, u8 *key, u8 *dst);
-+
-+void dwc_wusb_cmf(u8 *key, u8 *nonce,
-+ char *label, u8 *bytes, int len, u8 *result);
-+void dwc_wusb_prf(int prf_len, u8 *key,
-+ u8 *nonce, char *label, u8 *bytes, int len, u8 *result);
-+
-+/**
-+ * The PRF-64 function described in section 6.5 of the WUSB spec.
-+ *
-+ * @param key, nonce, label, bytes, len, result Same as for dwc_prf().
-+ */
-+static inline void dwc_wusb_prf_64(u8 *key, u8 *nonce,
-+ char *label, u8 *bytes, int len, u8 *result)
-+{
-+ dwc_wusb_prf(64, key, nonce, label, bytes, len, result);
-+}
-+
-+/**
-+ * The PRF-128 function described in section 6.5 of the WUSB spec.
-+ *
-+ * @param key, nonce, label, bytes, len, result Same as for dwc_prf().
-+ */
-+static inline void dwc_wusb_prf_128(u8 *key, u8 *nonce,
-+ char *label, u8 *bytes, int len, u8 *result)
-+{
-+ dwc_wusb_prf(128, key, nonce, label, bytes, len, result);
-+}
-+
-+/**
-+ * The PRF-256 function described in section 6.5 of the WUSB spec.
-+ *
-+ * @param key, nonce, label, bytes, len, result Same as for dwc_prf().
-+ */
-+static inline void dwc_wusb_prf_256(u8 *key, u8 *nonce,
-+ char *label, u8 *bytes, int len, u8 *result)
-+{
-+ dwc_wusb_prf(256, key, nonce, label, bytes, len, result);
-+}
-+
-+
-+void dwc_wusb_fill_ccm_nonce(uint16_t haddr, uint16_t daddr, uint8_t *tkid,
-+ uint8_t *nonce);
-+void dwc_wusb_gen_nonce(uint16_t addr,
-+ uint8_t *nonce);
-+
-+void dwc_wusb_gen_key(uint8_t *ccm_nonce, uint8_t *mk,
-+ uint8_t *hnonce, uint8_t *dnonce,
-+ uint8_t *kck, uint8_t *ptk);
-+
-+
-+void dwc_wusb_gen_mic(uint8_t *ccm_nonce, uint8_t
-+ *kck, uint8_t *data, uint8_t *mic);
-+
-+#ifdef __cplusplus
-+}
-+#endif
-+
-+#endif /* _DWC_CRYPTO_H_ */
---- /dev/null
-+++ b/drivers/usb/host/dwc_common_port/dwc_dh.c
-@@ -0,0 +1,291 @@
-+/* =========================================================================
-+ * $File: //dwh/usb_iip/dev/software/dwc_common_port_2/dwc_dh.c $
-+ * $Revision: #3 $
-+ * $Date: 2010/09/28 $
-+ * $Change: 1596182 $
-+ *
-+ * Synopsys Portability Library Software and documentation
-+ * (hereinafter, "Software") is an Unsupported proprietary work of
-+ * Synopsys, Inc. unless otherwise expressly agreed to in writing
-+ * between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product
-+ * under any End User Software License Agreement or Agreement for
-+ * Licensed Product with Synopsys or any supplement thereto. You are
-+ * permitted to use and redistribute this Software in source and binary
-+ * forms, with or without modification, provided that redistributions
-+ * of source code must retain this notice. You may not view, use,
-+ * disclose, copy or distribute this file or any information contained
-+ * herein except pursuant to this license grant from Synopsys. If you
-+ * do not agree with this notice, including the disclaimer below, then
-+ * you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS"
-+ * BASIS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
-+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
-+ * FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. IN NO EVENT SHALL
-+ * SYNOPSYS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY
-+ * OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
-+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
-+ * USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================= */
-+#ifdef DWC_CRYPTOLIB
-+
-+#ifndef CONFIG_MACH_IPMATE
-+
-+#include "dwc_dh.h"
-+#include "dwc_modpow.h"
-+
-+#ifdef DEBUG
-+/* This function prints out a buffer in the format described in the Association
-+ * Model specification. */
-+static void dh_dump(char *str, void *_num, int len)
-+{
-+ uint8_t *num = _num;
-+ int i;
-+ DWC_PRINTF("%s\n", str);
-+ for (i = 0; i < len; i ++) {
-+ DWC_PRINTF("%02x", num[i]);
-+ if (((i + 1) % 2) == 0) DWC_PRINTF(" ");
-+ if (((i + 1) % 26) == 0) DWC_PRINTF("\n");
-+ }
-+
-+ DWC_PRINTF("\n");
-+}
-+#else
-+#define dh_dump(_x...) do {; } while(0)
-+#endif
-+
-+/* Constant g value */
-+static __u32 dh_g[] = {
-+ 0x02000000,
-+};
-+
-+/* Constant p value */
-+static __u32 dh_p[] = {
-+ 0xFFFFFFFF, 0xFFFFFFFF, 0xA2DA0FC9, 0x34C26821, 0x8B62C6C4, 0xD11CDC80, 0x084E0229, 0x74CC678A,
-+ 0xA6BE0B02, 0x229B133B, 0x79084A51, 0xDD04348E, 0xB31995EF, 0x1B433ACD, 0x6D0A2B30, 0x37145FF2,
-+ 0x6D35E14F, 0x45C2516D, 0x76B585E4, 0xC67E5E62, 0xE9424CF4, 0x6BED37A6, 0xB65CFF0B, 0xEDB706F4,
-+ 0xFB6B38EE, 0xA59F895A, 0x11249FAE, 0xE61F4B7C, 0x51662849, 0x3D5BE4EC, 0xB87C00C2, 0x05BF63A1,
-+ 0x3648DA98, 0x9AD3551C, 0xA83F1669, 0x5FCF24FD, 0x235D6583, 0x96ADA3DC, 0x56F3621C, 0xBB528520,
-+ 0x0729D59E, 0x6D969670, 0x4E350C67, 0x0498BC4A, 0x086C74F1, 0x7C2118CA, 0x465E9032, 0x3BCE362E,
-+ 0x2C779EE3, 0x03860E18, 0xA283279B, 0x8FA207EC, 0xF05DC5B5, 0xC9524C6F, 0xF6CB2BDE, 0x18175895,
-+ 0x7C499539, 0xE56A95EA, 0x1826D215, 0x1005FA98, 0x5A8E7215, 0x2DC4AA8A, 0x0D1733AD, 0x337A5004,
-+ 0xAB2155A8, 0x64BA1CDF, 0x0485FBEC, 0x0AEFDB58, 0x5771EA8A, 0x7D0C065D, 0x850F97B3, 0xC7E4E1A6,
-+ 0x8CAEF5AB, 0xD73309DB, 0xE0948C1E, 0x9D61254A, 0x26D2E3CE, 0x6BEED21A, 0x06FA2FF1, 0x64088AD9,
-+ 0x730276D8, 0x646AC83E, 0x182B1F52, 0x0C207B17, 0x5717E1BB, 0x6C5D617A, 0xC0880977, 0xE246D9BA,
-+ 0xA04FE208, 0x31ABE574, 0xFC5BDB43, 0x8E10FDE0, 0x20D1824B, 0xCAD23AA9, 0xFFFFFFFF, 0xFFFFFFFF,
-+};
-+
-+static void dh_swap_bytes(void *_in, void *_out, uint32_t len)
-+{
-+ uint8_t *in = _in;
-+ uint8_t *out = _out;
-+ int i;
-+ for (i=0; i<len; i++) {
-+ out[i] = in[len-1-i];
-+ }
-+}
-+
-+/* Computes the modular exponentiation (num^exp % mod). num, exp, and mod are
-+ * big endian numbers of size len, in bytes. Each len value must be a multiple
-+ * of 4. */
-+int dwc_dh_modpow(void *mem_ctx, void *num, uint32_t num_len,
-+ void *exp, uint32_t exp_len,
-+ void *mod, uint32_t mod_len,
-+ void *out)
-+{
-+ /* modpow() takes little endian numbers. AM uses big-endian. This
-+ * function swaps bytes of numbers before passing onto modpow. */
-+
-+ int retval = 0;
-+ uint32_t *result;
-+
-+ uint32_t *bignum_num = dwc_alloc(mem_ctx, num_len + 4);
-+ uint32_t *bignum_exp = dwc_alloc(mem_ctx, exp_len + 4);
-+ uint32_t *bignum_mod = dwc_alloc(mem_ctx, mod_len + 4);
-+
-+ dh_swap_bytes(num, &bignum_num[1], num_len);
-+ bignum_num[0] = num_len / 4;
-+
-+ dh_swap_bytes(exp, &bignum_exp[1], exp_len);
-+ bignum_exp[0] = exp_len / 4;
-+
-+ dh_swap_bytes(mod, &bignum_mod[1], mod_len);
-+ bignum_mod[0] = mod_len / 4;
-+
-+ result = dwc_modpow(mem_ctx, bignum_num, bignum_exp, bignum_mod);
-+ if (!result) {
-+ retval = -1;
-+ goto dh_modpow_nomem;
-+ }
-+
-+ dh_swap_bytes(&result[1], out, result[0] * 4);
-+ dwc_free(mem_ctx, result);
-+
-+ dh_modpow_nomem:
-+ dwc_free(mem_ctx, bignum_num);
-+ dwc_free(mem_ctx, bignum_exp);
-+ dwc_free(mem_ctx, bignum_mod);
-+ return retval;
-+}
-+
-+
-+int dwc_dh_pk(void *mem_ctx, uint8_t nd, uint8_t *exp, uint8_t *pk, uint8_t *hash)
-+{
-+ int retval;
-+ uint8_t m3[385];
-+
-+#ifndef DH_TEST_VECTORS
-+ DWC_RANDOM_BYTES(exp, 32);
-+#endif
-+
-+ /* Compute the pkd */
-+ if ((retval = dwc_dh_modpow(mem_ctx, dh_g, 4,
-+ exp, 32,
-+ dh_p, 384, pk))) {
-+ return retval;
-+ }
-+
-+ m3[384] = nd;
-+ DWC_MEMCPY(&m3[0], pk, 384);
-+ DWC_SHA256(m3, 385, hash);
-+
-+ dh_dump("PK", pk, 384);
-+ dh_dump("SHA-256(M3)", hash, 32);
-+ return 0;
-+}
-+
-+int dwc_dh_derive_keys(void *mem_ctx, uint8_t nd, uint8_t *pkh, uint8_t *pkd,
-+ uint8_t *exp, int is_host,
-+ char *dd, uint8_t *ck, uint8_t *kdk)
-+{
-+ int retval;
-+ uint8_t mv[784];
-+ uint8_t sha_result[32];
-+ uint8_t dhkey[384];
-+ uint8_t shared_secret[384];
-+ char *message;
-+ uint32_t vd;
-+
-+ uint8_t *pk;
-+
-+ if (is_host) {
-+ pk = pkd;
-+ }
-+ else {
-+ pk = pkh;
-+ }
-+
-+ if ((retval = dwc_dh_modpow(mem_ctx, pk, 384,
-+ exp, 32,
-+ dh_p, 384, shared_secret))) {
-+ return retval;
-+ }
-+ dh_dump("Shared Secret", shared_secret, 384);
-+
-+ DWC_SHA256(shared_secret, 384, dhkey);
-+ dh_dump("DHKEY", dhkey, 384);
-+
-+ DWC_MEMCPY(&mv[0], pkd, 384);
-+ DWC_MEMCPY(&mv[384], pkh, 384);
-+ DWC_MEMCPY(&mv[768], "displayed digest", 16);
-+ dh_dump("MV", mv, 784);
-+
-+ DWC_SHA256(mv, 784, sha_result);
-+ dh_dump("SHA-256(MV)", sha_result, 32);
-+ dh_dump("First 32-bits of SHA-256(MV)", sha_result, 4);
-+
-+ dh_swap_bytes(sha_result, &vd, 4);
-+#ifdef DEBUG
-+ DWC_PRINTF("Vd (decimal) = %d\n", vd);
-+#endif
-+
-+ switch (nd) {
-+ case 2:
-+ vd = vd % 100;
-+ DWC_SPRINTF(dd, "%02d", vd);
-+ break;
-+ case 3:
-+ vd = vd % 1000;
-+ DWC_SPRINTF(dd, "%03d", vd);
-+ break;
-+ case 4:
-+ vd = vd % 10000;
-+ DWC_SPRINTF(dd, "%04d", vd);
-+ break;
-+ }
-+#ifdef DEBUG
-+ DWC_PRINTF("Display Digits: %s\n", dd);
-+#endif
-+
-+ message = "connection key";
-+ DWC_HMAC_SHA256(message, DWC_STRLEN(message), dhkey, 32, sha_result);
-+ dh_dump("HMAC(SHA-256, DHKey, connection key)", sha_result, 32);
-+ DWC_MEMCPY(ck, sha_result, 16);
-+
-+ message = "key derivation key";
-+ DWC_HMAC_SHA256(message, DWC_STRLEN(message), dhkey, 32, sha_result);
-+ dh_dump("HMAC(SHA-256, DHKey, key derivation key)", sha_result, 32);
-+ DWC_MEMCPY(kdk, sha_result, 32);
-+
-+ return 0;
-+}
-+
-+
-+#ifdef DH_TEST_VECTORS
-+
-+static __u8 dh_a[] = {
-+ 0x44, 0x00, 0x51, 0xd6,
-+ 0xf0, 0xb5, 0x5e, 0xa9,
-+ 0x67, 0xab, 0x31, 0xc6,
-+ 0x8a, 0x8b, 0x5e, 0x37,
-+ 0xd9, 0x10, 0xda, 0xe0,
-+ 0xe2, 0xd4, 0x59, 0xa4,
-+ 0x86, 0x45, 0x9c, 0xaa,
-+ 0xdf, 0x36, 0x75, 0x16,
-+};
-+
-+static __u8 dh_b[] = {
-+ 0x5d, 0xae, 0xc7, 0x86,
-+ 0x79, 0x80, 0xa3, 0x24,
-+ 0x8c, 0xe3, 0x57, 0x8f,
-+ 0xc7, 0x5f, 0x1b, 0x0f,
-+ 0x2d, 0xf8, 0x9d, 0x30,
-+ 0x6f, 0xa4, 0x52, 0xcd,
-+ 0xe0, 0x7a, 0x04, 0x8a,
-+ 0xde, 0xd9, 0x26, 0x56,
-+};
-+
-+void dwc_run_dh_test_vectors(void *mem_ctx)
-+{
-+ uint8_t pkd[384];
-+ uint8_t pkh[384];
-+ uint8_t hashd[32];
-+ uint8_t hashh[32];
-+ uint8_t ck[16];
-+ uint8_t kdk[32];
-+ char dd[5];
-+
-+ DWC_PRINTF("\n\n\nDH_TEST_VECTORS\n\n");
-+
-+ /* compute the PKd and SHA-256(PKd || Nd) */
-+ DWC_PRINTF("Computing PKd\n");
-+ dwc_dh_pk(mem_ctx, 2, dh_a, pkd, hashd);
-+
-+ /* compute the PKd and SHA-256(PKh || Nd) */
-+ DWC_PRINTF("Computing PKh\n");
-+ dwc_dh_pk(mem_ctx, 2, dh_b, pkh, hashh);
-+
-+ /* compute the dhkey */
-+ dwc_dh_derive_keys(mem_ctx, 2, pkh, pkd, dh_a, 0, dd, ck, kdk);
-+}
-+#endif /* DH_TEST_VECTORS */
-+
-+#endif /* !CONFIG_MACH_IPMATE */
-+
-+#endif /* DWC_CRYPTOLIB */
---- /dev/null
-+++ b/drivers/usb/host/dwc_common_port/dwc_dh.h
-@@ -0,0 +1,106 @@
-+/* =========================================================================
-+ * $File: //dwh/usb_iip/dev/software/dwc_common_port_2/dwc_dh.h $
-+ * $Revision: #4 $
-+ * $Date: 2010/09/28 $
-+ * $Change: 1596182 $
-+ *
-+ * Synopsys Portability Library Software and documentation
-+ * (hereinafter, "Software") is an Unsupported proprietary work of
-+ * Synopsys, Inc. unless otherwise expressly agreed to in writing
-+ * between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product
-+ * under any End User Software License Agreement or Agreement for
-+ * Licensed Product with Synopsys or any supplement thereto. You are
-+ * permitted to use and redistribute this Software in source and binary
-+ * forms, with or without modification, provided that redistributions
-+ * of source code must retain this notice. You may not view, use,
-+ * disclose, copy or distribute this file or any information contained
-+ * herein except pursuant to this license grant from Synopsys. If you
-+ * do not agree with this notice, including the disclaimer below, then
-+ * you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS"
-+ * BASIS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
-+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
-+ * FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. IN NO EVENT SHALL
-+ * SYNOPSYS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY
-+ * OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
-+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
-+ * USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================= */
-+#ifndef _DWC_DH_H_
-+#define _DWC_DH_H_
-+
-+#ifdef __cplusplus
-+extern "C" {
-+#endif
-+
-+#include "dwc_os.h"
-+
-+/** @file
-+ *
-+ * This file defines the common functions on device and host for performing
-+ * numeric association as defined in the WUSB spec. They are only to be
-+ * used internally by the DWC UWB modules. */
-+
-+extern int dwc_dh_sha256(uint8_t *message, uint32_t len, uint8_t *out);
-+extern int dwc_dh_hmac_sha256(uint8_t *message, uint32_t messagelen,
-+ uint8_t *key, uint32_t keylen,
-+ uint8_t *out);
-+extern int dwc_dh_modpow(void *mem_ctx, void *num, uint32_t num_len,
-+ void *exp, uint32_t exp_len,
-+ void *mod, uint32_t mod_len,
-+ void *out);
-+
-+/** Computes PKD or PKH, and SHA-256(PKd || Nd)
-+ *
-+ * PK = g^exp mod p.
-+ *
-+ * Input:
-+ * Nd = Number of digits on the device.
-+ *
-+ * Output:
-+ * exp = A 32-byte buffer to be filled with a randomly generated number.
-+ * used as either A or B.
-+ * pk = A 384-byte buffer to be filled with the PKH or PKD.
-+ * hash = A 32-byte buffer to be filled with SHA-256(PK || ND).
-+ */
-+extern int dwc_dh_pk(void *mem_ctx, uint8_t nd, uint8_t *exp, uint8_t *pkd, uint8_t *hash);
-+
-+/** Computes the DHKEY, and VD.
-+ *
-+ * If called from host, then it will comput DHKEY=PKD^exp % p.
-+ * If called from device, then it will comput DHKEY=PKH^exp % p.
-+ *
-+ * Input:
-+ * pkd = The PKD value.
-+ * pkh = The PKH value.
-+ * exp = The A value (if device) or B value (if host) generated in dwc_wudev_dh_pk.
-+ * is_host = Set to non zero if a WUSB host is calling this function.
-+ *
-+ * Output:
-+
-+ * dd = A pointer to an buffer to be set to the displayed digits string to be shown
-+ * to the user. This buffer should be at 5 bytes long to hold 4 digits plus a
-+ * null termination character. This buffer can be used directly for display.
-+ * ck = A 16-byte buffer to be filled with the CK.
-+ * kdk = A 32-byte buffer to be filled with the KDK.
-+ */
-+extern int dwc_dh_derive_keys(void *mem_ctx, uint8_t nd, uint8_t *pkh, uint8_t *pkd,
-+ uint8_t *exp, int is_host,
-+ char *dd, uint8_t *ck, uint8_t *kdk);
-+
-+#ifdef DH_TEST_VECTORS
-+extern void dwc_run_dh_test_vectors(void);
-+#endif
-+
-+#ifdef __cplusplus
-+}
-+#endif
-+
-+#endif /* _DWC_DH_H_ */
---- /dev/null
-+++ b/drivers/usb/host/dwc_common_port/dwc_list.h
-@@ -0,0 +1,594 @@
-+/* $OpenBSD: queue.h,v 1.26 2004/05/04 16:59:32 grange Exp $ */
-+/* $NetBSD: queue.h,v 1.11 1996/05/16 05:17:14 mycroft Exp $ */
-+
-+/*
-+ * Copyright (c) 1991, 1993
-+ * The Regents of the University of California. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions and the following disclaimer.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. Neither the name of the University nor the names of its contributors
-+ * may be used to endorse or promote products derived from this software
-+ * without specific prior written permission.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND
-+ * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE
-+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
-+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
-+ * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
-+ * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
-+ * SUCH DAMAGE.
-+ *
-+ * @(#)queue.h 8.5 (Berkeley) 8/20/94
-+ */
-+
-+#ifndef _DWC_LIST_H_
-+#define _DWC_LIST_H_
-+
-+#ifdef __cplusplus
-+extern "C" {
-+#endif
-+
-+/** @file
-+ *
-+ * This file defines linked list operations. It is derived from BSD with
-+ * only the MACRO names being prefixed with DWC_. This is because a few of
-+ * these names conflict with those on Linux. For documentation on use, see the
-+ * inline comments in the source code. The original license for this source
-+ * code applies and is preserved in the dwc_list.h source file.
-+ */
-+
-+/*
-+ * This file defines five types of data structures: singly-linked lists,
-+ * lists, simple queues, tail queues, and circular queues.
-+ *
-+ *
-+ * A singly-linked list is headed by a single forward pointer. The elements
-+ * are singly linked for minimum space and pointer manipulation overhead at
-+ * the expense of O(n) removal for arbitrary elements. New elements can be
-+ * added to the list after an existing element or at the head of the list.
-+ * Elements being removed from the head of the list should use the explicit
-+ * macro for this purpose for optimum efficiency. A singly-linked list may
-+ * only be traversed in the forward direction. Singly-linked lists are ideal
-+ * for applications with large datasets and few or no removals or for
-+ * implementing a LIFO queue.
-+ *
-+ * A list is headed by a single forward pointer (or an array of forward
-+ * pointers for a hash table header). The elements are doubly linked
-+ * so that an arbitrary element can be removed without a need to
-+ * traverse the list. New elements can be added to the list before
-+ * or after an existing element or at the head of the list. A list
-+ * may only be traversed in the forward direction.
-+ *
-+ * A simple queue is headed by a pair of pointers, one the head of the
-+ * list and the other to the tail of the list. The elements are singly
-+ * linked to save space, so elements can only be removed from the
-+ * head of the list. New elements can be added to the list before or after
-+ * an existing element, at the head of the list, or at the end of the
-+ * list. A simple queue may only be traversed in the forward direction.
-+ *
-+ * A tail queue is headed by a pair of pointers, one to the head of the
-+ * list and the other to the tail of the list. The elements are doubly
-+ * linked so that an arbitrary element can be removed without a need to
-+ * traverse the list. New elements can be added to the list before or
-+ * after an existing element, at the head of the list, or at the end of
-+ * the list. A tail queue may be traversed in either direction.
-+ *
-+ * A circle queue is headed by a pair of pointers, one to the head of the
-+ * list and the other to the tail of the list. The elements are doubly
-+ * linked so that an arbitrary element can be removed without a need to
-+ * traverse the list. New elements can be added to the list before or after
-+ * an existing element, at the head of the list, or at the end of the list.
-+ * A circle queue may be traversed in either direction, but has a more
-+ * complex end of list detection.
-+ *
-+ * For details on the use of these macros, see the queue(3) manual page.
-+ */
-+
-+/*
-+ * Double-linked List.
-+ */
-+
-+typedef struct dwc_list_link {
-+ struct dwc_list_link *next;
-+ struct dwc_list_link *prev;
-+} dwc_list_link_t;
-+
-+#define DWC_LIST_INIT(link) do { \
-+ (link)->next = (link); \
-+ (link)->prev = (link); \
-+} while (0)
-+
-+#define DWC_LIST_FIRST(link) ((link)->next)
-+#define DWC_LIST_LAST(link) ((link)->prev)
-+#define DWC_LIST_END(link) (link)
-+#define DWC_LIST_NEXT(link) ((link)->next)
-+#define DWC_LIST_PREV(link) ((link)->prev)
-+#define DWC_LIST_EMPTY(link) \
-+ (DWC_LIST_FIRST(link) == DWC_LIST_END(link))
-+#define DWC_LIST_ENTRY(link, type, field) \
-+ (type *)((uint8_t *)(link) - (size_t)(&((type *)0)->field))
-+
-+#if 0
-+#define DWC_LIST_INSERT_HEAD(list, link) do { \
-+ (link)->next = (list)->next; \
-+ (link)->prev = (list); \
-+ (list)->next->prev = (link); \
-+ (list)->next = (link); \
-+} while (0)
-+
-+#define DWC_LIST_INSERT_TAIL(list, link) do { \
-+ (link)->next = (list); \
-+ (link)->prev = (list)->prev; \
-+ (list)->prev->next = (link); \
-+ (list)->prev = (link); \
-+} while (0)
-+#else
-+#define DWC_LIST_INSERT_HEAD(list, link) do { \
-+ dwc_list_link_t *__next__ = (list)->next; \
-+ __next__->prev = (link); \
-+ (link)->next = __next__; \
-+ (link)->prev = (list); \
-+ (list)->next = (link); \
-+} while (0)
-+
-+#define DWC_LIST_INSERT_TAIL(list, link) do { \
-+ dwc_list_link_t *__prev__ = (list)->prev; \
-+ (list)->prev = (link); \
-+ (link)->next = (list); \
-+ (link)->prev = __prev__; \
-+ __prev__->next = (link); \
-+} while (0)
-+#endif
-+
-+#if 0
-+static inline void __list_add(struct list_head *new,
-+ struct list_head *prev,
-+ struct list_head *next)
-+{
-+ next->prev = new;
-+ new->next = next;
-+ new->prev = prev;
-+ prev->next = new;
-+}
-+
-+static inline void list_add(struct list_head *new, struct list_head *head)
-+{
-+ __list_add(new, head, head->next);
-+}
-+
-+static inline void list_add_tail(struct list_head *new, struct list_head *head)
-+{
-+ __list_add(new, head->prev, head);
-+}
-+
-+static inline void __list_del(struct list_head * prev, struct list_head * next)
-+{
-+ next->prev = prev;
-+ prev->next = next;
-+}
-+
-+static inline void list_del(struct list_head *entry)
-+{
-+ __list_del(entry->prev, entry->next);
-+ entry->next = LIST_POISON1;
-+ entry->prev = LIST_POISON2;
-+}
-+#endif
-+
-+#define DWC_LIST_REMOVE(link) do { \
-+ (link)->next->prev = (link)->prev; \
-+ (link)->prev->next = (link)->next; \
-+} while (0)
-+
-+#define DWC_LIST_REMOVE_INIT(link) do { \
-+ DWC_LIST_REMOVE(link); \
-+ DWC_LIST_INIT(link); \
-+} while (0)
-+
-+#define DWC_LIST_MOVE_HEAD(list, link) do { \
-+ DWC_LIST_REMOVE(link); \
-+ DWC_LIST_INSERT_HEAD(list, link); \
-+} while (0)
-+
-+#define DWC_LIST_MOVE_TAIL(list, link) do { \
-+ DWC_LIST_REMOVE(link); \
-+ DWC_LIST_INSERT_TAIL(list, link); \
-+} while (0)
-+
-+#define DWC_LIST_FOREACH(var, list) \
-+ for((var) = DWC_LIST_FIRST(list); \
-+ (var) != DWC_LIST_END(list); \
-+ (var) = DWC_LIST_NEXT(var))
-+
-+#define DWC_LIST_FOREACH_SAFE(var, var2, list) \
-+ for((var) = DWC_LIST_FIRST(list), (var2) = DWC_LIST_NEXT(var); \
-+ (var) != DWC_LIST_END(list); \
-+ (var) = (var2), (var2) = DWC_LIST_NEXT(var2))
-+
-+#define DWC_LIST_FOREACH_REVERSE(var, list) \
-+ for((var) = DWC_LIST_LAST(list); \
-+ (var) != DWC_LIST_END(list); \
-+ (var) = DWC_LIST_PREV(var))
-+
-+/*
-+ * Singly-linked List definitions.
-+ */
-+#define DWC_SLIST_HEAD(name, type) \
-+struct name { \
-+ struct type *slh_first; /* first element */ \
-+}
-+
-+#define DWC_SLIST_HEAD_INITIALIZER(head) \
-+ { NULL }
-+
-+#define DWC_SLIST_ENTRY(type) \
-+struct { \
-+ struct type *sle_next; /* next element */ \
-+}
-+
-+/*
-+ * Singly-linked List access methods.
-+ */
-+#define DWC_SLIST_FIRST(head) ((head)->slh_first)
-+#define DWC_SLIST_END(head) NULL
-+#define DWC_SLIST_EMPTY(head) (SLIST_FIRST(head) == SLIST_END(head))
-+#define DWC_SLIST_NEXT(elm, field) ((elm)->field.sle_next)
-+
-+#define DWC_SLIST_FOREACH(var, head, field) \
-+ for((var) = SLIST_FIRST(head); \
-+ (var) != SLIST_END(head); \
-+ (var) = SLIST_NEXT(var, field))
-+
-+#define DWC_SLIST_FOREACH_PREVPTR(var, varp, head, field) \
-+ for((varp) = &SLIST_FIRST((head)); \
-+ ((var) = *(varp)) != SLIST_END(head); \
-+ (varp) = &SLIST_NEXT((var), field))
-+
-+/*
-+ * Singly-linked List functions.
-+ */
-+#define DWC_SLIST_INIT(head) { \
-+ SLIST_FIRST(head) = SLIST_END(head); \
-+}
-+
-+#define DWC_SLIST_INSERT_AFTER(slistelm, elm, field) do { \
-+ (elm)->field.sle_next = (slistelm)->field.sle_next; \
-+ (slistelm)->field.sle_next = (elm); \
-+} while (0)
-+
-+#define DWC_SLIST_INSERT_HEAD(head, elm, field) do { \
-+ (elm)->field.sle_next = (head)->slh_first; \
-+ (head)->slh_first = (elm); \
-+} while (0)
-+
-+#define DWC_SLIST_REMOVE_NEXT(head, elm, field) do { \
-+ (elm)->field.sle_next = (elm)->field.sle_next->field.sle_next; \
-+} while (0)
-+
-+#define DWC_SLIST_REMOVE_HEAD(head, field) do { \
-+ (head)->slh_first = (head)->slh_first->field.sle_next; \
-+} while (0)
-+
-+#define DWC_SLIST_REMOVE(head, elm, type, field) do { \
-+ if ((head)->slh_first == (elm)) { \
-+ SLIST_REMOVE_HEAD((head), field); \
-+ } \
-+ else { \
-+ struct type *curelm = (head)->slh_first; \
-+ while( curelm->field.sle_next != (elm) ) \
-+ curelm = curelm->field.sle_next; \
-+ curelm->field.sle_next = \
-+ curelm->field.sle_next->field.sle_next; \
-+ } \
-+} while (0)
-+
-+/*
-+ * Simple queue definitions.
-+ */
-+#define DWC_SIMPLEQ_HEAD(name, type) \
-+struct name { \
-+ struct type *sqh_first; /* first element */ \
-+ struct type **sqh_last; /* addr of last next element */ \
-+}
-+
-+#define DWC_SIMPLEQ_HEAD_INITIALIZER(head) \
-+ { NULL, &(head).sqh_first }
-+
-+#define DWC_SIMPLEQ_ENTRY(type) \
-+struct { \
-+ struct type *sqe_next; /* next element */ \
-+}
-+
-+/*
-+ * Simple queue access methods.
-+ */
-+#define DWC_SIMPLEQ_FIRST(head) ((head)->sqh_first)
-+#define DWC_SIMPLEQ_END(head) NULL
-+#define DWC_SIMPLEQ_EMPTY(head) (SIMPLEQ_FIRST(head) == SIMPLEQ_END(head))
-+#define DWC_SIMPLEQ_NEXT(elm, field) ((elm)->field.sqe_next)
-+
-+#define DWC_SIMPLEQ_FOREACH(var, head, field) \
-+ for((var) = SIMPLEQ_FIRST(head); \
-+ (var) != SIMPLEQ_END(head); \
-+ (var) = SIMPLEQ_NEXT(var, field))
-+
-+/*
-+ * Simple queue functions.
-+ */
-+#define DWC_SIMPLEQ_INIT(head) do { \
-+ (head)->sqh_first = NULL; \
-+ (head)->sqh_last = &(head)->sqh_first; \
-+} while (0)
-+
-+#define DWC_SIMPLEQ_INSERT_HEAD(head, elm, field) do { \
-+ if (((elm)->field.sqe_next = (head)->sqh_first) == NULL) \
-+ (head)->sqh_last = &(elm)->field.sqe_next; \
-+ (head)->sqh_first = (elm); \
-+} while (0)
-+
-+#define DWC_SIMPLEQ_INSERT_TAIL(head, elm, field) do { \
-+ (elm)->field.sqe_next = NULL; \
-+ *(head)->sqh_last = (elm); \
-+ (head)->sqh_last = &(elm)->field.sqe_next; \
-+} while (0)
-+
-+#define DWC_SIMPLEQ_INSERT_AFTER(head, listelm, elm, field) do { \
-+ if (((elm)->field.sqe_next = (listelm)->field.sqe_next) == NULL)\
-+ (head)->sqh_last = &(elm)->field.sqe_next; \
-+ (listelm)->field.sqe_next = (elm); \
-+} while (0)
-+
-+#define DWC_SIMPLEQ_REMOVE_HEAD(head, field) do { \
-+ if (((head)->sqh_first = (head)->sqh_first->field.sqe_next) == NULL) \
-+ (head)->sqh_last = &(head)->sqh_first; \
-+} while (0)
-+
-+/*
-+ * Tail queue definitions.
-+ */
-+#define DWC_TAILQ_HEAD(name, type) \
-+struct name { \
-+ struct type *tqh_first; /* first element */ \
-+ struct type **tqh_last; /* addr of last next element */ \
-+}
-+
-+#define DWC_TAILQ_HEAD_INITIALIZER(head) \
-+ { NULL, &(head).tqh_first }
-+
-+#define DWC_TAILQ_ENTRY(type) \
-+struct { \
-+ struct type *tqe_next; /* next element */ \
-+ struct type **tqe_prev; /* address of previous next element */ \
-+}
-+
-+/*
-+ * tail queue access methods
-+ */
-+#define DWC_TAILQ_FIRST(head) ((head)->tqh_first)
-+#define DWC_TAILQ_END(head) NULL
-+#define DWC_TAILQ_NEXT(elm, field) ((elm)->field.tqe_next)
-+#define DWC_TAILQ_LAST(head, headname) \
-+ (*(((struct headname *)((head)->tqh_last))->tqh_last))
-+/* XXX */
-+#define DWC_TAILQ_PREV(elm, headname, field) \
-+ (*(((struct headname *)((elm)->field.tqe_prev))->tqh_last))
-+#define DWC_TAILQ_EMPTY(head) \
-+ (DWC_TAILQ_FIRST(head) == DWC_TAILQ_END(head))
-+
-+#define DWC_TAILQ_FOREACH(var, head, field) \
-+ for ((var) = DWC_TAILQ_FIRST(head); \
-+ (var) != DWC_TAILQ_END(head); \
-+ (var) = DWC_TAILQ_NEXT(var, field))
-+
-+#define DWC_TAILQ_FOREACH_REVERSE(var, head, headname, field) \
-+ for ((var) = DWC_TAILQ_LAST(head, headname); \
-+ (var) != DWC_TAILQ_END(head); \
-+ (var) = DWC_TAILQ_PREV(var, headname, field))
-+
-+/*
-+ * Tail queue functions.
-+ */
-+#define DWC_TAILQ_INIT(head) do { \
-+ (head)->tqh_first = NULL; \
-+ (head)->tqh_last = &(head)->tqh_first; \
-+} while (0)
-+
-+#define DWC_TAILQ_INSERT_HEAD(head, elm, field) do { \
-+ if (((elm)->field.tqe_next = (head)->tqh_first) != NULL) \
-+ (head)->tqh_first->field.tqe_prev = \
-+ &(elm)->field.tqe_next; \
-+ else \
-+ (head)->tqh_last = &(elm)->field.tqe_next; \
-+ (head)->tqh_first = (elm); \
-+ (elm)->field.tqe_prev = &(head)->tqh_first; \
-+} while (0)
-+
-+#define DWC_TAILQ_INSERT_TAIL(head, elm, field) do { \
-+ (elm)->field.tqe_next = NULL; \
-+ (elm)->field.tqe_prev = (head)->tqh_last; \
-+ *(head)->tqh_last = (elm); \
-+ (head)->tqh_last = &(elm)->field.tqe_next; \
-+} while (0)
-+
-+#define DWC_TAILQ_INSERT_AFTER(head, listelm, elm, field) do { \
-+ if (((elm)->field.tqe_next = (listelm)->field.tqe_next) != NULL)\
-+ (elm)->field.tqe_next->field.tqe_prev = \
-+ &(elm)->field.tqe_next; \
-+ else \
-+ (head)->tqh_last = &(elm)->field.tqe_next; \
-+ (listelm)->field.tqe_next = (elm); \
-+ (elm)->field.tqe_prev = &(listelm)->field.tqe_next; \
-+} while (0)
-+
-+#define DWC_TAILQ_INSERT_BEFORE(listelm, elm, field) do { \
-+ (elm)->field.tqe_prev = (listelm)->field.tqe_prev; \
-+ (elm)->field.tqe_next = (listelm); \
-+ *(listelm)->field.tqe_prev = (elm); \
-+ (listelm)->field.tqe_prev = &(elm)->field.tqe_next; \
-+} while (0)
-+
-+#define DWC_TAILQ_REMOVE(head, elm, field) do { \
-+ if (((elm)->field.tqe_next) != NULL) \
-+ (elm)->field.tqe_next->field.tqe_prev = \
-+ (elm)->field.tqe_prev; \
-+ else \
-+ (head)->tqh_last = (elm)->field.tqe_prev; \
-+ *(elm)->field.tqe_prev = (elm)->field.tqe_next; \
-+} while (0)
-+
-+#define DWC_TAILQ_REPLACE(head, elm, elm2, field) do { \
-+ if (((elm2)->field.tqe_next = (elm)->field.tqe_next) != NULL) \
-+ (elm2)->field.tqe_next->field.tqe_prev = \
-+ &(elm2)->field.tqe_next; \
-+ else \
-+ (head)->tqh_last = &(elm2)->field.tqe_next; \
-+ (elm2)->field.tqe_prev = (elm)->field.tqe_prev; \
-+ *(elm2)->field.tqe_prev = (elm2); \
-+} while (0)
-+
-+/*
-+ * Circular queue definitions.
-+ */
-+#define DWC_CIRCLEQ_HEAD(name, type) \
-+struct name { \
-+ struct type *cqh_first; /* first element */ \
-+ struct type *cqh_last; /* last element */ \
-+}
-+
-+#define DWC_CIRCLEQ_HEAD_INITIALIZER(head) \
-+ { DWC_CIRCLEQ_END(&head), DWC_CIRCLEQ_END(&head) }
-+
-+#define DWC_CIRCLEQ_ENTRY(type) \
-+struct { \
-+ struct type *cqe_next; /* next element */ \
-+ struct type *cqe_prev; /* previous element */ \
-+}
-+
-+/*
-+ * Circular queue access methods
-+ */
-+#define DWC_CIRCLEQ_FIRST(head) ((head)->cqh_first)
-+#define DWC_CIRCLEQ_LAST(head) ((head)->cqh_last)
-+#define DWC_CIRCLEQ_END(head) ((void *)(head))
-+#define DWC_CIRCLEQ_NEXT(elm, field) ((elm)->field.cqe_next)
-+#define DWC_CIRCLEQ_PREV(elm, field) ((elm)->field.cqe_prev)
-+#define DWC_CIRCLEQ_EMPTY(head) \
-+ (DWC_CIRCLEQ_FIRST(head) == DWC_CIRCLEQ_END(head))
-+
-+#define DWC_CIRCLEQ_EMPTY_ENTRY(elm, field) (((elm)->field.cqe_next == NULL) && ((elm)->field.cqe_prev == NULL))
-+
-+#define DWC_CIRCLEQ_FOREACH(var, head, field) \
-+ for((var) = DWC_CIRCLEQ_FIRST(head); \
-+ (var) != DWC_CIRCLEQ_END(head); \
-+ (var) = DWC_CIRCLEQ_NEXT(var, field))
-+
-+#define DWC_CIRCLEQ_FOREACH_SAFE(var, var2, head, field) \
-+ for((var) = DWC_CIRCLEQ_FIRST(head), var2 = DWC_CIRCLEQ_NEXT(var, field); \
-+ (var) != DWC_CIRCLEQ_END(head); \
-+ (var) = var2, var2 = DWC_CIRCLEQ_NEXT(var, field))
-+
-+#define DWC_CIRCLEQ_FOREACH_REVERSE(var, head, field) \
-+ for((var) = DWC_CIRCLEQ_LAST(head); \
-+ (var) != DWC_CIRCLEQ_END(head); \
-+ (var) = DWC_CIRCLEQ_PREV(var, field))
-+
-+/*
-+ * Circular queue functions.
-+ */
-+#define DWC_CIRCLEQ_INIT(head) do { \
-+ (head)->cqh_first = DWC_CIRCLEQ_END(head); \
-+ (head)->cqh_last = DWC_CIRCLEQ_END(head); \
-+} while (0)
-+
-+#define DWC_CIRCLEQ_INIT_ENTRY(elm, field) do { \
-+ (elm)->field.cqe_next = NULL; \
-+ (elm)->field.cqe_prev = NULL; \
-+} while (0)
-+
-+#define DWC_CIRCLEQ_INSERT_AFTER(head, listelm, elm, field) do { \
-+ (elm)->field.cqe_next = (listelm)->field.cqe_next; \
-+ (elm)->field.cqe_prev = (listelm); \
-+ if ((listelm)->field.cqe_next == DWC_CIRCLEQ_END(head)) \
-+ (head)->cqh_last = (elm); \
-+ else \
-+ (listelm)->field.cqe_next->field.cqe_prev = (elm); \
-+ (listelm)->field.cqe_next = (elm); \
-+} while (0)
-+
-+#define DWC_CIRCLEQ_INSERT_BEFORE(head, listelm, elm, field) do { \
-+ (elm)->field.cqe_next = (listelm); \
-+ (elm)->field.cqe_prev = (listelm)->field.cqe_prev; \
-+ if ((listelm)->field.cqe_prev == DWC_CIRCLEQ_END(head)) \
-+ (head)->cqh_first = (elm); \
-+ else \
-+ (listelm)->field.cqe_prev->field.cqe_next = (elm); \
-+ (listelm)->field.cqe_prev = (elm); \
-+} while (0)
-+
-+#define DWC_CIRCLEQ_INSERT_HEAD(head, elm, field) do { \
-+ (elm)->field.cqe_next = (head)->cqh_first; \
-+ (elm)->field.cqe_prev = DWC_CIRCLEQ_END(head); \
-+ if ((head)->cqh_last == DWC_CIRCLEQ_END(head)) \
-+ (head)->cqh_last = (elm); \
-+ else \
-+ (head)->cqh_first->field.cqe_prev = (elm); \
-+ (head)->cqh_first = (elm); \
-+} while (0)
-+
-+#define DWC_CIRCLEQ_INSERT_TAIL(head, elm, field) do { \
-+ (elm)->field.cqe_next = DWC_CIRCLEQ_END(head); \
-+ (elm)->field.cqe_prev = (head)->cqh_last; \
-+ if ((head)->cqh_first == DWC_CIRCLEQ_END(head)) \
-+ (head)->cqh_first = (elm); \
-+ else \
-+ (head)->cqh_last->field.cqe_next = (elm); \
-+ (head)->cqh_last = (elm); \
-+} while (0)
-+
-+#define DWC_CIRCLEQ_REMOVE(head, elm, field) do { \
-+ if ((elm)->field.cqe_next == DWC_CIRCLEQ_END(head)) \
-+ (head)->cqh_last = (elm)->field.cqe_prev; \
-+ else \
-+ (elm)->field.cqe_next->field.cqe_prev = \
-+ (elm)->field.cqe_prev; \
-+ if ((elm)->field.cqe_prev == DWC_CIRCLEQ_END(head)) \
-+ (head)->cqh_first = (elm)->field.cqe_next; \
-+ else \
-+ (elm)->field.cqe_prev->field.cqe_next = \
-+ (elm)->field.cqe_next; \
-+} while (0)
-+
-+#define DWC_CIRCLEQ_REMOVE_INIT(head, elm, field) do { \
-+ DWC_CIRCLEQ_REMOVE(head, elm, field); \
-+ DWC_CIRCLEQ_INIT_ENTRY(elm, field); \
-+} while (0)
-+
-+#define DWC_CIRCLEQ_REPLACE(head, elm, elm2, field) do { \
-+ if (((elm2)->field.cqe_next = (elm)->field.cqe_next) == \
-+ DWC_CIRCLEQ_END(head)) \
-+ (head).cqh_last = (elm2); \
-+ else \
-+ (elm2)->field.cqe_next->field.cqe_prev = (elm2); \
-+ if (((elm2)->field.cqe_prev = (elm)->field.cqe_prev) == \
-+ DWC_CIRCLEQ_END(head)) \
-+ (head).cqh_first = (elm2); \
-+ else \
-+ (elm2)->field.cqe_prev->field.cqe_next = (elm2); \
-+} while (0)
-+
-+#ifdef __cplusplus
-+}
-+#endif
-+
-+#endif /* _DWC_LIST_H_ */
---- /dev/null
-+++ b/drivers/usb/host/dwc_common_port/dwc_mem.c
-@@ -0,0 +1,245 @@
-+/* Memory Debugging */
-+#ifdef DWC_DEBUG_MEMORY
-+
-+#include "dwc_os.h"
-+#include "dwc_list.h"
-+
-+struct allocation {
-+ void *addr;
-+ void *ctx;
-+ char *func;
-+ int line;
-+ uint32_t size;
-+ int dma;
-+ DWC_CIRCLEQ_ENTRY(allocation) entry;
-+};
-+
-+DWC_CIRCLEQ_HEAD(allocation_queue, allocation);
-+
-+struct allocation_manager {
-+ void *mem_ctx;
-+ struct allocation_queue allocations;
-+
-+ /* statistics */
-+ int num;
-+ int num_freed;
-+ int num_active;
-+ uint32_t total;
-+ uint32_t cur;
-+ uint32_t max;
-+};
-+
-+static struct allocation_manager *manager = NULL;
-+
-+static int add_allocation(void *ctx, uint32_t size, char const *func, int line, void *addr,
-+ int dma)
-+{
-+ struct allocation *a;
-+
-+ DWC_ASSERT(manager != NULL, "manager not allocated");
-+
-+ a = __DWC_ALLOC_ATOMIC(manager->mem_ctx, sizeof(*a));
-+ if (!a) {
-+ return -DWC_E_NO_MEMORY;
-+ }
-+
-+ a->func = __DWC_ALLOC_ATOMIC(manager->mem_ctx, DWC_STRLEN(func) + 1);
-+ if (!a->func) {
-+ __DWC_FREE(manager->mem_ctx, a);
-+ return -DWC_E_NO_MEMORY;
-+ }
-+
-+ DWC_MEMCPY(a->func, func, DWC_STRLEN(func) + 1);
-+ a->addr = addr;
-+ a->ctx = ctx;
-+ a->line = line;
-+ a->size = size;
-+ a->dma = dma;
-+ DWC_CIRCLEQ_INSERT_TAIL(&manager->allocations, a, entry);
-+
-+ /* Update stats */
-+ manager->num++;
-+ manager->num_active++;
-+ manager->total += size;
-+ manager->cur += size;
-+
-+ if (manager->max < manager->cur) {
-+ manager->max = manager->cur;
-+ }
-+
-+ return 0;
-+}
-+
-+static struct allocation *find_allocation(void *ctx, void *addr)
-+{
-+ struct allocation *a;
-+
-+ DWC_CIRCLEQ_FOREACH(a, &manager->allocations, entry) {
-+ if (a->ctx == ctx && a->addr == addr) {
-+ return a;
-+ }
-+ }
-+
-+ return NULL;
-+}
-+
-+static void free_allocation(void *ctx, void *addr, char const *func, int line)
-+{
-+ struct allocation *a = find_allocation(ctx, addr);
-+
-+ if (!a) {
-+ DWC_ASSERT(0,
-+ "Free of address %p that was never allocated or already freed %s:%d",
-+ addr, func, line);
-+ return;
-+ }
-+
-+ DWC_CIRCLEQ_REMOVE(&manager->allocations, a, entry);
-+
-+ manager->num_active--;
-+ manager->num_freed++;
-+ manager->cur -= a->size;
-+ __DWC_FREE(manager->mem_ctx, a->func);
-+ __DWC_FREE(manager->mem_ctx, a);
-+}
-+
-+int dwc_memory_debug_start(void *mem_ctx)
-+{
-+ DWC_ASSERT(manager == NULL, "Memory debugging has already started\n");
-+
-+ if (manager) {
-+ return -DWC_E_BUSY;
-+ }
-+
-+ manager = __DWC_ALLOC(mem_ctx, sizeof(*manager));
-+ if (!manager) {
-+ return -DWC_E_NO_MEMORY;
-+ }
-+
-+ DWC_CIRCLEQ_INIT(&manager->allocations);
-+ manager->mem_ctx = mem_ctx;
-+ manager->num = 0;
-+ manager->num_freed = 0;
-+ manager->num_active = 0;
-+ manager->total = 0;
-+ manager->cur = 0;
-+ manager->max = 0;
-+
-+ return 0;
-+}
-+
-+void dwc_memory_debug_stop(void)
-+{
-+ struct allocation *a;
-+
-+ dwc_memory_debug_report();
-+
-+ DWC_CIRCLEQ_FOREACH(a, &manager->allocations, entry) {
-+ DWC_ERROR("Memory leaked from %s:%d\n", a->func, a->line);
-+ free_allocation(a->ctx, a->addr, NULL, -1);
-+ }
-+
-+ __DWC_FREE(manager->mem_ctx, manager);
-+}
-+
-+void dwc_memory_debug_report(void)
-+{
-+ struct allocation *a;
-+
-+ DWC_PRINTF("\n\n\n----------------- Memory Debugging Report -----------------\n\n");
-+ DWC_PRINTF("Num Allocations = %d\n", manager->num);
-+ DWC_PRINTF("Freed = %d\n", manager->num_freed);
-+ DWC_PRINTF("Active = %d\n", manager->num_active);
-+ DWC_PRINTF("Current Memory Used = %d\n", manager->cur);
-+ DWC_PRINTF("Total Memory Used = %d\n", manager->total);
-+ DWC_PRINTF("Maximum Memory Used at Once = %d\n", manager->max);
-+ DWC_PRINTF("Unfreed allocations:\n");
-+
-+ DWC_CIRCLEQ_FOREACH(a, &manager->allocations, entry) {
-+ DWC_PRINTF(" addr=%p, size=%d from %s:%d, DMA=%d\n",
-+ a->addr, a->size, a->func, a->line, a->dma);
-+ }
-+}
-+
-+/* The replacement functions */
-+void *dwc_alloc_debug(void *mem_ctx, uint32_t size, char const *func, int line)
-+{
-+ void *addr = __DWC_ALLOC(mem_ctx, size);
-+
-+ if (!addr) {
-+ return NULL;
-+ }
-+
-+ if (add_allocation(mem_ctx, size, func, line, addr, 0)) {
-+ __DWC_FREE(mem_ctx, addr);
-+ return NULL;
-+ }
-+
-+ return addr;
-+}
-+
-+void *dwc_alloc_atomic_debug(void *mem_ctx, uint32_t size, char const *func,
-+ int line)
-+{
-+ void *addr = __DWC_ALLOC_ATOMIC(mem_ctx, size);
-+
-+ if (!addr) {
-+ return NULL;
-+ }
-+
-+ if (add_allocation(mem_ctx, size, func, line, addr, 0)) {
-+ __DWC_FREE(mem_ctx, addr);
-+ return NULL;
-+ }
-+
-+ return addr;
-+}
-+
-+void dwc_free_debug(void *mem_ctx, void *addr, char const *func, int line)
-+{
-+ free_allocation(mem_ctx, addr, func, line);
-+ __DWC_FREE(mem_ctx, addr);
-+}
-+
-+void *dwc_dma_alloc_debug(void *dma_ctx, uint32_t size, dwc_dma_t *dma_addr,
-+ char const *func, int line)
-+{
-+ void *addr = __DWC_DMA_ALLOC(dma_ctx, size, dma_addr);
-+
-+ if (!addr) {
-+ return NULL;
-+ }
-+
-+ if (add_allocation(dma_ctx, size, func, line, addr, 1)) {
-+ __DWC_DMA_FREE(dma_ctx, size, addr, *dma_addr);
-+ return NULL;
-+ }
-+
-+ return addr;
-+}
-+
-+void *dwc_dma_alloc_atomic_debug(void *dma_ctx, uint32_t size,
-+ dwc_dma_t *dma_addr, char const *func, int line)
-+{
-+ void *addr = __DWC_DMA_ALLOC_ATOMIC(dma_ctx, size, dma_addr);
-+
-+ if (!addr) {
-+ return NULL;
-+ }
-+
-+ if (add_allocation(dma_ctx, size, func, line, addr, 1)) {
-+ __DWC_DMA_FREE(dma_ctx, size, addr, *dma_addr);
-+ return NULL;
-+ }
-+
-+ return addr;
-+}
-+
-+void dwc_dma_free_debug(void *dma_ctx, uint32_t size, void *virt_addr,
-+ dwc_dma_t dma_addr, char const *func, int line)
-+{
-+ free_allocation(dma_ctx, virt_addr, func, line);
-+ __DWC_DMA_FREE(dma_ctx, size, virt_addr, dma_addr);
-+}
-+
-+#endif /* DWC_DEBUG_MEMORY */
---- /dev/null
-+++ b/drivers/usb/host/dwc_common_port/dwc_modpow.c
-@@ -0,0 +1,636 @@
-+/* Bignum routines adapted from PUTTY sources. PuTTY copyright notice follows.
-+ *
-+ * PuTTY is copyright 1997-2007 Simon Tatham.
-+ *
-+ * Portions copyright Robert de Bath, Joris van Rantwijk, Delian
-+ * Delchev, Andreas Schultz, Jeroen Massar, Wez Furlong, Nicolas Barry,
-+ * Justin Bradford, Ben Harris, Malcolm Smith, Ahmad Khalifa, Markus
-+ * Kuhn, and CORE SDI S.A.
-+ *
-+ * Permission is hereby granted, free of charge, to any person
-+ * obtaining a copy of this software and associated documentation files
-+ * (the "Software"), to deal in the Software without restriction,
-+ * including without limitation the rights to use, copy, modify, merge,
-+ * publish, distribute, sublicense, and/or sell copies of the Software,
-+ * and to permit persons to whom the Software is furnished to do so,
-+ * subject to the following conditions:
-+ *
-+ * The above copyright notice and this permission notice shall be
-+ * included in all copies or substantial portions of the Software.
-+
-+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
-+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
-+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
-+ * NONINFRINGEMENT. IN NO EVENT SHALL THE COPYRIGHT HOLDERS BE LIABLE
-+ * FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF
-+ * CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION
-+ * WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
-+ *
-+ */
-+#ifdef DWC_CRYPTOLIB
-+
-+#ifndef CONFIG_MACH_IPMATE
-+
-+#include "dwc_modpow.h"
-+
-+#define BIGNUM_INT_MASK 0xFFFFFFFFUL
-+#define BIGNUM_TOP_BIT 0x80000000UL
-+#define BIGNUM_INT_BITS 32
-+
-+
-+static void *snmalloc(void *mem_ctx, size_t n, size_t size)
-+{
-+ void *p;
-+ size *= n;
-+ if (size == 0) size = 1;
-+ p = dwc_alloc(mem_ctx, size);
-+ return p;
-+}
-+
-+#define snewn(ctx, n, type) ((type *)snmalloc((ctx), (n), sizeof(type)))
-+#define sfree dwc_free
-+
-+/*
-+ * Usage notes:
-+ * * Do not call the DIVMOD_WORD macro with expressions such as array
-+ * subscripts, as some implementations object to this (see below).
-+ * * Note that none of the division methods below will cope if the
-+ * quotient won't fit into BIGNUM_INT_BITS. Callers should be careful
-+ * to avoid this case.
-+ * If this condition occurs, in the case of the x86 DIV instruction,
-+ * an overflow exception will occur, which (according to a correspondent)
-+ * will manifest on Windows as something like
-+ * 0xC0000095: Integer overflow
-+ * The C variant won't give the right answer, either.
-+ */
-+
-+#define MUL_WORD(w1, w2) ((BignumDblInt)w1 * w2)
-+
-+#if defined __GNUC__ && defined __i386__
-+#define DIVMOD_WORD(q, r, hi, lo, w) \
-+ __asm__("div %2" : \
-+ "=d" (r), "=a" (q) : \
-+ "r" (w), "d" (hi), "a" (lo))
-+#else
-+#define DIVMOD_WORD(q, r, hi, lo, w) do { \
-+ BignumDblInt n = (((BignumDblInt)hi) << BIGNUM_INT_BITS) | lo; \
-+ q = n / w; \
-+ r = n % w; \
-+} while (0)
-+#endif
-+
-+// q = n / w;
-+// r = n % w;
-+
-+#define BIGNUM_INT_BYTES (BIGNUM_INT_BITS / 8)
-+
-+#define BIGNUM_INTERNAL
-+
-+static Bignum newbn(void *mem_ctx, int length)
-+{
-+ Bignum b = snewn(mem_ctx, length + 1, BignumInt);
-+ //if (!b)
-+ //abort(); /* FIXME */
-+ DWC_MEMSET(b, 0, (length + 1) * sizeof(*b));
-+ b[0] = length;
-+ return b;
-+}
-+
-+void freebn(void *mem_ctx, Bignum b)
-+{
-+ /*
-+ * Burn the evidence, just in case.
-+ */
-+ DWC_MEMSET(b, 0, sizeof(b[0]) * (b[0] + 1));
-+ sfree(mem_ctx, b);
-+}
-+
-+/*
-+ * Compute c = a * b.
-+ * Input is in the first len words of a and b.
-+ * Result is returned in the first 2*len words of c.
-+ */
-+static void internal_mul(BignumInt *a, BignumInt *b,
-+ BignumInt *c, int len)
-+{
-+ int i, j;
-+ BignumDblInt t;
-+
-+ for (j = 0; j < 2 * len; j++)
-+ c[j] = 0;
-+
-+ for (i = len - 1; i >= 0; i--) {
-+ t = 0;
-+ for (j = len - 1; j >= 0; j--) {
-+ t += MUL_WORD(a[i], (BignumDblInt) b[j]);
-+ t += (BignumDblInt) c[i + j + 1];
-+ c[i + j + 1] = (BignumInt) t;
-+ t = t >> BIGNUM_INT_BITS;
-+ }
-+ c[i] = (BignumInt) t;
-+ }
-+}
-+
-+static void internal_add_shifted(BignumInt *number,
-+ unsigned n, int shift)
-+{
-+ int word = 1 + (shift / BIGNUM_INT_BITS);
-+ int bshift = shift % BIGNUM_INT_BITS;
-+ BignumDblInt addend;
-+
-+ addend = (BignumDblInt)n << bshift;
-+
-+ while (addend) {
-+ addend += number[word];
-+ number[word] = (BignumInt) addend & BIGNUM_INT_MASK;
-+ addend >>= BIGNUM_INT_BITS;
-+ word++;
-+ }
-+}
-+
-+/*
-+ * Compute a = a % m.
-+ * Input in first alen words of a and first mlen words of m.
-+ * Output in first alen words of a
-+ * (of which first alen-mlen words will be zero).
-+ * The MSW of m MUST have its high bit set.
-+ * Quotient is accumulated in the `quotient' array, which is a Bignum
-+ * rather than the internal bigendian format. Quotient parts are shifted
-+ * left by `qshift' before adding into quot.
-+ */
-+static void internal_mod(BignumInt *a, int alen,
-+ BignumInt *m, int mlen,
-+ BignumInt *quot, int qshift)
-+{
-+ BignumInt m0, m1;
-+ unsigned int h;
-+ int i, k;
-+
-+ m0 = m[0];
-+ if (mlen > 1)
-+ m1 = m[1];
-+ else
-+ m1 = 0;
-+
-+ for (i = 0; i <= alen - mlen; i++) {
-+ BignumDblInt t;
-+ unsigned int q, r, c, ai1;
-+
-+ if (i == 0) {
-+ h = 0;
-+ } else {
-+ h = a[i - 1];
-+ a[i - 1] = 0;
-+ }
-+
-+ if (i == alen - 1)
-+ ai1 = 0;
-+ else
-+ ai1 = a[i + 1];
-+
-+ /* Find q = h:a[i] / m0 */
-+ if (h >= m0) {
-+ /*
-+ * Special case.
-+ *
-+ * To illustrate it, suppose a BignumInt is 8 bits, and
-+ * we are dividing (say) A1:23:45:67 by A1:B2:C3. Then
-+ * our initial division will be 0xA123 / 0xA1, which
-+ * will give a quotient of 0x100 and a divide overflow.
-+ * However, the invariants in this division algorithm
-+ * are not violated, since the full number A1:23:... is
-+ * _less_ than the quotient prefix A1:B2:... and so the
-+ * following correction loop would have sorted it out.
-+ *
-+ * In this situation we set q to be the largest
-+ * quotient we _can_ stomach (0xFF, of course).
-+ */
-+ q = BIGNUM_INT_MASK;
-+ } else {
-+ /* Macro doesn't want an array subscript expression passed
-+ * into it (see definition), so use a temporary. */
-+ BignumInt tmplo = a[i];
-+ DIVMOD_WORD(q, r, h, tmplo, m0);
-+
-+ /* Refine our estimate of q by looking at
-+ h:a[i]:a[i+1] / m0:m1 */
-+ t = MUL_WORD(m1, q);
-+ if (t > ((BignumDblInt) r << BIGNUM_INT_BITS) + ai1) {
-+ q--;
-+ t -= m1;
-+ r = (r + m0) & BIGNUM_INT_MASK; /* overflow? */
-+ if (r >= (BignumDblInt) m0 &&
-+ t > ((BignumDblInt) r << BIGNUM_INT_BITS) + ai1) q--;
-+ }
-+ }
-+
-+ /* Subtract q * m from a[i...] */
-+ c = 0;
-+ for (k = mlen - 1; k >= 0; k--) {
-+ t = MUL_WORD(q, m[k]);
-+ t += c;
-+ c = (unsigned)(t >> BIGNUM_INT_BITS);
-+ if ((BignumInt) t > a[i + k])
-+ c++;
-+ a[i + k] -= (BignumInt) t;
-+ }
-+
-+ /* Add back m in case of borrow */
-+ if (c != h) {
-+ t = 0;
-+ for (k = mlen - 1; k >= 0; k--) {
-+ t += m[k];
-+ t += a[i + k];
-+ a[i + k] = (BignumInt) t;
-+ t = t >> BIGNUM_INT_BITS;
-+ }
-+ q--;
-+ }
-+ if (quot)
-+ internal_add_shifted(quot, q, qshift + BIGNUM_INT_BITS * (alen - mlen - i));
-+ }
-+}
-+
-+/*
-+ * Compute p % mod.
-+ * The most significant word of mod MUST be non-zero.
-+ * We assume that the result array is the same size as the mod array.
-+ * We optionally write out a quotient if `quotient' is non-NULL.
-+ * We can avoid writing out the result if `result' is NULL.
-+ */
-+void bigdivmod(void *mem_ctx, Bignum p, Bignum mod, Bignum result, Bignum quotient)
-+{
-+ BignumInt *n, *m;
-+ int mshift;
-+ int plen, mlen, i, j;
-+
-+ /* Allocate m of size mlen, copy mod to m */
-+ /* We use big endian internally */
-+ mlen = mod[0];
-+ m = snewn(mem_ctx, mlen, BignumInt);
-+ //if (!m)
-+ //abort(); /* FIXME */
-+ for (j = 0; j < mlen; j++)
-+ m[j] = mod[mod[0] - j];
-+
-+ /* Shift m left to make msb bit set */
-+ for (mshift = 0; mshift < BIGNUM_INT_BITS-1; mshift++)
-+ if ((m[0] << mshift) & BIGNUM_TOP_BIT)
-+ break;
-+ if (mshift) {
-+ for (i = 0; i < mlen - 1; i++)
-+ m[i] = (m[i] << mshift) | (m[i + 1] >> (BIGNUM_INT_BITS - mshift));
-+ m[mlen - 1] = m[mlen - 1] << mshift;
-+ }
-+
-+ plen = p[0];
-+ /* Ensure plen > mlen */
-+ if (plen <= mlen)
-+ plen = mlen + 1;
-+
-+ /* Allocate n of size plen, copy p to n */
-+ n = snewn(mem_ctx, plen, BignumInt);
-+ //if (!n)
-+ //abort(); /* FIXME */
-+ for (j = 0; j < plen; j++)
-+ n[j] = 0;
-+ for (j = 1; j <= (int)p[0]; j++)
-+ n[plen - j] = p[j];
-+
-+ /* Main computation */
-+ internal_mod(n, plen, m, mlen, quotient, mshift);
-+
-+ /* Fixup result in case the modulus was shifted */
-+ if (mshift) {
-+ for (i = plen - mlen - 1; i < plen - 1; i++)
-+ n[i] = (n[i] << mshift) | (n[i + 1] >> (BIGNUM_INT_BITS - mshift));
-+ n[plen - 1] = n[plen - 1] << mshift;
-+ internal_mod(n, plen, m, mlen, quotient, 0);
-+ for (i = plen - 1; i >= plen - mlen; i--)
-+ n[i] = (n[i] >> mshift) | (n[i - 1] << (BIGNUM_INT_BITS - mshift));
-+ }
-+
-+ /* Copy result to buffer */
-+ if (result) {
-+ for (i = 1; i <= (int)result[0]; i++) {
-+ int j = plen - i;
-+ result[i] = j >= 0 ? n[j] : 0;
-+ }
-+ }
-+
-+ /* Free temporary arrays */
-+ for (i = 0; i < mlen; i++)
-+ m[i] = 0;
-+ sfree(mem_ctx, m);
-+ for (i = 0; i < plen; i++)
-+ n[i] = 0;
-+ sfree(mem_ctx, n);
-+}
-+
-+/*
-+ * Simple remainder.
-+ */
-+Bignum bigmod(void *mem_ctx, Bignum a, Bignum b)
-+{
-+ Bignum r = newbn(mem_ctx, b[0]);
-+ bigdivmod(mem_ctx, a, b, r, NULL);
-+ return r;
-+}
-+
-+/*
-+ * Compute (base ^ exp) % mod.
-+ */
-+Bignum dwc_modpow(void *mem_ctx, Bignum base_in, Bignum exp, Bignum mod)
-+{
-+ BignumInt *a, *b, *n, *m;
-+ int mshift;
-+ int mlen, i, j;
-+ Bignum base, result;
-+
-+ /*
-+ * The most significant word of mod needs to be non-zero. It
-+ * should already be, but let's make sure.
-+ */
-+ //assert(mod[mod[0]] != 0);
-+
-+ /*
-+ * Make sure the base is smaller than the modulus, by reducing
-+ * it modulo the modulus if not.
-+ */
-+ base = bigmod(mem_ctx, base_in, mod);
-+
-+ /* Allocate m of size mlen, copy mod to m */
-+ /* We use big endian internally */
-+ mlen = mod[0];
-+ m = snewn(mem_ctx, mlen, BignumInt);
-+ //if (!m)
-+ //abort(); /* FIXME */
-+ for (j = 0; j < mlen; j++)
-+ m[j] = mod[mod[0] - j];
-+
-+ /* Shift m left to make msb bit set */
-+ for (mshift = 0; mshift < BIGNUM_INT_BITS - 1; mshift++)
-+ if ((m[0] << mshift) & BIGNUM_TOP_BIT)
-+ break;
-+ if (mshift) {
-+ for (i = 0; i < mlen - 1; i++)
-+ m[i] =
-+ (m[i] << mshift) | (m[i + 1] >>
-+ (BIGNUM_INT_BITS - mshift));
-+ m[mlen - 1] = m[mlen - 1] << mshift;
-+ }
-+
-+ /* Allocate n of size mlen, copy base to n */
-+ n = snewn(mem_ctx, mlen, BignumInt);
-+ //if (!n)
-+ //abort(); /* FIXME */
-+ i = mlen - base[0];
-+ for (j = 0; j < i; j++)
-+ n[j] = 0;
-+ for (j = 0; j < base[0]; j++)
-+ n[i + j] = base[base[0] - j];
-+
-+ /* Allocate a and b of size 2*mlen. Set a = 1 */
-+ a = snewn(mem_ctx, 2 * mlen, BignumInt);
-+ //if (!a)
-+ //abort(); /* FIXME */
-+ b = snewn(mem_ctx, 2 * mlen, BignumInt);
-+ //if (!b)
-+ //abort(); /* FIXME */
-+ for (i = 0; i < 2 * mlen; i++)
-+ a[i] = 0;
-+ a[2 * mlen - 1] = 1;
-+
-+ /* Skip leading zero bits of exp. */
-+ i = 0;
-+ j = BIGNUM_INT_BITS - 1;
-+ while (i < exp[0] && (exp[exp[0] - i] & (1 << j)) == 0) {
-+ j--;
-+ if (j < 0) {
-+ i++;
-+ j = BIGNUM_INT_BITS - 1;
-+ }
-+ }
-+
-+ /* Main computation */
-+ while (i < exp[0]) {
-+ while (j >= 0) {
-+ internal_mul(a + mlen, a + mlen, b, mlen);
-+ internal_mod(b, mlen * 2, m, mlen, NULL, 0);
-+ if ((exp[exp[0] - i] & (1 << j)) != 0) {
-+ internal_mul(b + mlen, n, a, mlen);
-+ internal_mod(a, mlen * 2, m, mlen, NULL, 0);
-+ } else {
-+ BignumInt *t;
-+ t = a;
-+ a = b;
-+ b = t;
-+ }
-+ j--;
-+ }
-+ i++;
-+ j = BIGNUM_INT_BITS - 1;
-+ }
-+
-+ /* Fixup result in case the modulus was shifted */
-+ if (mshift) {
-+ for (i = mlen - 1; i < 2 * mlen - 1; i++)
-+ a[i] =
-+ (a[i] << mshift) | (a[i + 1] >>
-+ (BIGNUM_INT_BITS - mshift));
-+ a[2 * mlen - 1] = a[2 * mlen - 1] << mshift;
-+ internal_mod(a, mlen * 2, m, mlen, NULL, 0);
-+ for (i = 2 * mlen - 1; i >= mlen; i--)
-+ a[i] =
-+ (a[i] >> mshift) | (a[i - 1] <<
-+ (BIGNUM_INT_BITS - mshift));
-+ }
-+
-+ /* Copy result to buffer */
-+ result = newbn(mem_ctx, mod[0]);
-+ for (i = 0; i < mlen; i++)
-+ result[result[0] - i] = a[i + mlen];
-+ while (result[0] > 1 && result[result[0]] == 0)
-+ result[0]--;
-+
-+ /* Free temporary arrays */
-+ for (i = 0; i < 2 * mlen; i++)
-+ a[i] = 0;
-+ sfree(mem_ctx, a);
-+ for (i = 0; i < 2 * mlen; i++)
-+ b[i] = 0;
-+ sfree(mem_ctx, b);
-+ for (i = 0; i < mlen; i++)
-+ m[i] = 0;
-+ sfree(mem_ctx, m);
-+ for (i = 0; i < mlen; i++)
-+ n[i] = 0;
-+ sfree(mem_ctx, n);
-+
-+ freebn(mem_ctx, base);
-+
-+ return result;
-+}
-+
-+
-+#ifdef UNITTEST
-+
-+static __u32 dh_p[] = {
-+ 96,
-+ 0xFFFFFFFF,
-+ 0xFFFFFFFF,
-+ 0xA93AD2CA,
-+ 0x4B82D120,
-+ 0xE0FD108E,
-+ 0x43DB5BFC,
-+ 0x74E5AB31,
-+ 0x08E24FA0,
-+ 0xBAD946E2,
-+ 0x770988C0,
-+ 0x7A615D6C,
-+ 0xBBE11757,
-+ 0x177B200C,
-+ 0x521F2B18,
-+ 0x3EC86A64,
-+ 0xD8760273,
-+ 0xD98A0864,
-+ 0xF12FFA06,
-+ 0x1AD2EE6B,
-+ 0xCEE3D226,
-+ 0x4A25619D,
-+ 0x1E8C94E0,
-+ 0xDB0933D7,
-+ 0xABF5AE8C,
-+ 0xA6E1E4C7,
-+ 0xB3970F85,
-+ 0x5D060C7D,
-+ 0x8AEA7157,
-+ 0x58DBEF0A,
-+ 0xECFB8504,
-+ 0xDF1CBA64,
-+ 0xA85521AB,
-+ 0x04507A33,
-+ 0xAD33170D,
-+ 0x8AAAC42D,
-+ 0x15728E5A,
-+ 0x98FA0510,
-+ 0x15D22618,
-+ 0xEA956AE5,
-+ 0x3995497C,
-+ 0x95581718,
-+ 0xDE2BCBF6,
-+ 0x6F4C52C9,
-+ 0xB5C55DF0,
-+ 0xEC07A28F,
-+ 0x9B2783A2,
-+ 0x180E8603,
-+ 0xE39E772C,
-+ 0x2E36CE3B,
-+ 0x32905E46,
-+ 0xCA18217C,
-+ 0xF1746C08,
-+ 0x4ABC9804,
-+ 0x670C354E,
-+ 0x7096966D,
-+ 0x9ED52907,
-+ 0x208552BB,
-+ 0x1C62F356,
-+ 0xDCA3AD96,
-+ 0x83655D23,
-+ 0xFD24CF5F,
-+ 0x69163FA8,
-+ 0x1C55D39A,
-+ 0x98DA4836,
-+ 0xA163BF05,
-+ 0xC2007CB8,
-+ 0xECE45B3D,
-+ 0x49286651,
-+ 0x7C4B1FE6,
-+ 0xAE9F2411,
-+ 0x5A899FA5,
-+ 0xEE386BFB,
-+ 0xF406B7ED,
-+ 0x0BFF5CB6,
-+ 0xA637ED6B,
-+ 0xF44C42E9,
-+ 0x625E7EC6,
-+ 0xE485B576,
-+ 0x6D51C245,
-+ 0x4FE1356D,
-+ 0xF25F1437,
-+ 0x302B0A6D,
-+ 0xCD3A431B,
-+ 0xEF9519B3,
-+ 0x8E3404DD,
-+ 0x514A0879,
-+ 0x3B139B22,
-+ 0x020BBEA6,
-+ 0x8A67CC74,
-+ 0x29024E08,
-+ 0x80DC1CD1,
-+ 0xC4C6628B,
-+ 0x2168C234,
-+ 0xC90FDAA2,
-+ 0xFFFFFFFF,
-+ 0xFFFFFFFF,
-+};
-+
-+static __u32 dh_a[] = {
-+ 8,
-+ 0xdf367516,
-+ 0x86459caa,
-+ 0xe2d459a4,
-+ 0xd910dae0,
-+ 0x8a8b5e37,
-+ 0x67ab31c6,
-+ 0xf0b55ea9,
-+ 0x440051d6,
-+};
-+
-+static __u32 dh_b[] = {
-+ 8,
-+ 0xded92656,
-+ 0xe07a048a,
-+ 0x6fa452cd,
-+ 0x2df89d30,
-+ 0xc75f1b0f,
-+ 0x8ce3578f,
-+ 0x7980a324,
-+ 0x5daec786,
-+};
-+
-+static __u32 dh_g[] = {
-+ 1,
-+ 2,
-+};
-+
-+int main(void)
-+{
-+ int i;
-+ __u32 *k;
-+ k = dwc_modpow(NULL, dh_g, dh_a, dh_p);
-+
-+ printf("\n\n");
-+ for (i=0; i<k[0]; i++) {
-+ __u32 word32 = k[k[0] - i];
-+ __u16 l = word32 & 0xffff;
-+ __u16 m = (word32 & 0xffff0000) >> 16;
-+ printf("%04x %04x ", m, l);
-+ if (!((i + 1)%13)) printf("\n");
-+ }
-+ printf("\n\n");
-+
-+ if ((k[0] == 0x60) && (k[1] == 0x28e490e5) && (k[0x60] == 0x5a0d3d4e)) {
-+ printf("PASS\n\n");
-+ }
-+ else {
-+ printf("FAIL\n\n");
-+ }
-+
-+}
-+
-+#endif /* UNITTEST */
-+
-+#endif /* CONFIG_MACH_IPMATE */
-+
-+#endif /*DWC_CRYPTOLIB */
---- /dev/null
-+++ b/drivers/usb/host/dwc_common_port/dwc_modpow.h
-@@ -0,0 +1,34 @@
-+/*
-+ * dwc_modpow.h
-+ * See dwc_modpow.c for license and changes
-+ */
-+#ifndef _DWC_MODPOW_H
-+#define _DWC_MODPOW_H
-+
-+#ifdef __cplusplus
-+extern "C" {
-+#endif
-+
-+#include "dwc_os.h"
-+
-+/** @file
-+ *
-+ * This file defines the module exponentiation function which is only used
-+ * internally by the DWC UWB modules for calculation of PKs during numeric
-+ * association. The routine is taken from the PUTTY, an open source terminal
-+ * emulator. The PUTTY License is preserved in the dwc_modpow.c file.
-+ *
-+ */
-+
-+typedef uint32_t BignumInt;
-+typedef uint64_t BignumDblInt;
-+typedef BignumInt *Bignum;
-+
-+/* Compute modular exponentiaion */
-+extern Bignum dwc_modpow(void *mem_ctx, Bignum base_in, Bignum exp, Bignum mod);
-+
-+#ifdef __cplusplus
-+}
-+#endif
-+
-+#endif /* _LINUX_BIGNUM_H */
---- /dev/null
-+++ b/drivers/usb/host/dwc_common_port/dwc_notifier.c
-@@ -0,0 +1,319 @@
-+#ifdef DWC_NOTIFYLIB
-+
-+#include "dwc_notifier.h"
-+#include "dwc_list.h"
-+
-+typedef struct dwc_observer {
-+ void *observer;
-+ dwc_notifier_callback_t callback;
-+ void *data;
-+ char *notification;
-+ DWC_CIRCLEQ_ENTRY(dwc_observer) list_entry;
-+} observer_t;
-+
-+DWC_CIRCLEQ_HEAD(observer_queue, dwc_observer);
-+
-+typedef struct dwc_notifier {
-+ void *mem_ctx;
-+ void *object;
-+ struct observer_queue observers;
-+ DWC_CIRCLEQ_ENTRY(dwc_notifier) list_entry;
-+} notifier_t;
-+
-+DWC_CIRCLEQ_HEAD(notifier_queue, dwc_notifier);
-+
-+typedef struct manager {
-+ void *mem_ctx;
-+ void *wkq_ctx;
-+ dwc_workq_t *wq;
-+// dwc_mutex_t *mutex;
-+ struct notifier_queue notifiers;
-+} manager_t;
-+
-+static manager_t *manager = NULL;
-+
-+static int create_manager(void *mem_ctx, void *wkq_ctx)
-+{
-+ manager = dwc_alloc(mem_ctx, sizeof(manager_t));
-+ if (!manager) {
-+ return -DWC_E_NO_MEMORY;
-+ }
-+
-+ DWC_CIRCLEQ_INIT(&manager->notifiers);
-+
-+ manager->wq = dwc_workq_alloc(wkq_ctx, "DWC Notification WorkQ");
-+ if (!manager->wq) {
-+ return -DWC_E_NO_MEMORY;
-+ }
-+
-+ return 0;
-+}
-+
-+static void free_manager(void)
-+{
-+ dwc_workq_free(manager->wq);
-+
-+ /* All notifiers must have unregistered themselves before this module
-+ * can be removed. Hitting this assertion indicates a programmer
-+ * error. */
-+ DWC_ASSERT(DWC_CIRCLEQ_EMPTY(&manager->notifiers),
-+ "Notification manager being freed before all notifiers have been removed");
-+ dwc_free(manager->mem_ctx, manager);
-+}
-+
-+#ifdef DEBUG
-+static void dump_manager(void)
-+{
-+ notifier_t *n;
-+ observer_t *o;
-+
-+ DWC_ASSERT(manager, "Notification manager not found");
-+
-+ DWC_DEBUG("List of all notifiers and observers:\n");
-+ DWC_CIRCLEQ_FOREACH(n, &manager->notifiers, list_entry) {
-+ DWC_DEBUG("Notifier %p has observers:\n", n->object);
-+ DWC_CIRCLEQ_FOREACH(o, &n->observers, list_entry) {
-+ DWC_DEBUG(" %p watching %s\n", o->observer, o->notification);
-+ }
-+ }
-+}
-+#else
-+#define dump_manager(...)
-+#endif
-+
-+static observer_t *alloc_observer(void *mem_ctx, void *observer, char *notification,
-+ dwc_notifier_callback_t callback, void *data)
-+{
-+ observer_t *new_observer = dwc_alloc(mem_ctx, sizeof(observer_t));
-+
-+ if (!new_observer) {
-+ return NULL;
-+ }
-+
-+ DWC_CIRCLEQ_INIT_ENTRY(new_observer, list_entry);
-+ new_observer->observer = observer;
-+ new_observer->notification = notification;
-+ new_observer->callback = callback;
-+ new_observer->data = data;
-+ return new_observer;
-+}
-+
-+static void free_observer(void *mem_ctx, observer_t *observer)
-+{
-+ dwc_free(mem_ctx, observer);
-+}
-+
-+static notifier_t *alloc_notifier(void *mem_ctx, void *object)
-+{
-+ notifier_t *notifier;
-+
-+ if (!object) {
-+ return NULL;
-+ }
-+
-+ notifier = dwc_alloc(mem_ctx, sizeof(notifier_t));
-+ if (!notifier) {
-+ return NULL;
-+ }
-+
-+ DWC_CIRCLEQ_INIT(¬ifier->observers);
-+ DWC_CIRCLEQ_INIT_ENTRY(notifier, list_entry);
-+
-+ notifier->mem_ctx = mem_ctx;
-+ notifier->object = object;
-+ return notifier;
-+}
-+
-+static void free_notifier(notifier_t *notifier)
-+{
-+ observer_t *observer;
-+
-+ DWC_CIRCLEQ_FOREACH(observer, ¬ifier->observers, list_entry) {
-+ free_observer(notifier->mem_ctx, observer);
-+ }
-+
-+ dwc_free(notifier->mem_ctx, notifier);
-+}
-+
-+static notifier_t *find_notifier(void *object)
-+{
-+ notifier_t *notifier;
-+
-+ DWC_ASSERT(manager, "Notification manager not found");
-+
-+ if (!object) {
-+ return NULL;
-+ }
-+
-+ DWC_CIRCLEQ_FOREACH(notifier, &manager->notifiers, list_entry) {
-+ if (notifier->object == object) {
-+ return notifier;
-+ }
-+ }
-+
-+ return NULL;
-+}
-+
-+int dwc_alloc_notification_manager(void *mem_ctx, void *wkq_ctx)
-+{
-+ return create_manager(mem_ctx, wkq_ctx);
-+}
-+
-+void dwc_free_notification_manager(void)
-+{
-+ free_manager();
-+}
-+
-+dwc_notifier_t *dwc_register_notifier(void *mem_ctx, void *object)
-+{
-+ notifier_t *notifier;
-+
-+ DWC_ASSERT(manager, "Notification manager not found");
-+
-+ notifier = find_notifier(object);
-+ if (notifier) {
-+ DWC_ERROR("Notifier %p is already registered\n", object);
-+ return NULL;
-+ }
-+
-+ notifier = alloc_notifier(mem_ctx, object);
-+ if (!notifier) {
-+ return NULL;
-+ }
-+
-+ DWC_CIRCLEQ_INSERT_TAIL(&manager->notifiers, notifier, list_entry);
-+
-+ DWC_INFO("Notifier %p registered", object);
-+ dump_manager();
-+
-+ return notifier;
-+}
-+
-+void dwc_unregister_notifier(dwc_notifier_t *notifier)
-+{
-+ DWC_ASSERT(manager, "Notification manager not found");
-+
-+ if (!DWC_CIRCLEQ_EMPTY(¬ifier->observers)) {
-+ observer_t *o;
-+
-+ DWC_ERROR("Notifier %p has active observers when removing\n", notifier->object);
-+ DWC_CIRCLEQ_FOREACH(o, ¬ifier->observers, list_entry) {
-+ DWC_DEBUGC(" %p watching %s\n", o->observer, o->notification);
-+ }
-+
-+ DWC_ASSERT(DWC_CIRCLEQ_EMPTY(¬ifier->observers),
-+ "Notifier %p has active observers when removing", notifier);
-+ }
-+
-+ DWC_CIRCLEQ_REMOVE_INIT(&manager->notifiers, notifier, list_entry);
-+ free_notifier(notifier);
-+
-+ DWC_INFO("Notifier unregistered");
-+ dump_manager();
-+}
-+
-+/* Add an observer to observe the notifier for a particular state, event, or notification. */
-+int dwc_add_observer(void *observer, void *object, char *notification,
-+ dwc_notifier_callback_t callback, void *data)
-+{
-+ notifier_t *notifier = find_notifier(object);
-+ observer_t *new_observer;
-+
-+ if (!notifier) {
-+ DWC_ERROR("Notifier %p is not found when adding observer\n", object);
-+ return -DWC_E_INVALID;
-+ }
-+
-+ new_observer = alloc_observer(notifier->mem_ctx, observer, notification, callback, data);
-+ if (!new_observer) {
-+ return -DWC_E_NO_MEMORY;
-+ }
-+
-+ DWC_CIRCLEQ_INSERT_TAIL(¬ifier->observers, new_observer, list_entry);
-+
-+ DWC_INFO("Added observer %p to notifier %p observing notification %s, callback=%p, data=%p",
-+ observer, object, notification, callback, data);
-+
-+ dump_manager();
-+ return 0;
-+}
-+
-+int dwc_remove_observer(void *observer)
-+{
-+ notifier_t *n;
-+
-+ DWC_ASSERT(manager, "Notification manager not found");
-+
-+ DWC_CIRCLEQ_FOREACH(n, &manager->notifiers, list_entry) {
-+ observer_t *o;
-+ observer_t *o2;
-+
-+ DWC_CIRCLEQ_FOREACH_SAFE(o, o2, &n->observers, list_entry) {
-+ if (o->observer == observer) {
-+ DWC_CIRCLEQ_REMOVE_INIT(&n->observers, o, list_entry);
-+ DWC_INFO("Removing observer %p from notifier %p watching notification %s:",
-+ o->observer, n->object, o->notification);
-+ free_observer(n->mem_ctx, o);
-+ }
-+ }
-+ }
-+
-+ dump_manager();
-+ return 0;
-+}
-+
-+typedef struct callback_data {
-+ void *mem_ctx;
-+ dwc_notifier_callback_t cb;
-+ void *observer;
-+ void *data;
-+ void *object;
-+ char *notification;
-+ void *notification_data;
-+} cb_data_t;
-+
-+static void cb_task(void *data)
-+{
-+ cb_data_t *cb = (cb_data_t *)data;
-+
-+ cb->cb(cb->object, cb->notification, cb->observer, cb->notification_data, cb->data);
-+ dwc_free(cb->mem_ctx, cb);
-+}
-+
-+void dwc_notify(dwc_notifier_t *notifier, char *notification, void *notification_data)
-+{
-+ observer_t *o;
-+
-+ DWC_ASSERT(manager, "Notification manager not found");
-+
-+ DWC_CIRCLEQ_FOREACH(o, ¬ifier->observers, list_entry) {
-+ int len = DWC_STRLEN(notification);
-+
-+ if (DWC_STRLEN(o->notification) != len) {
-+ continue;
-+ }
-+
-+ if (DWC_STRNCMP(o->notification, notification, len) == 0) {
-+ cb_data_t *cb_data = dwc_alloc(notifier->mem_ctx, sizeof(cb_data_t));
-+
-+ if (!cb_data) {
-+ DWC_ERROR("Failed to allocate callback data\n");
-+ return;
-+ }
-+
-+ cb_data->mem_ctx = notifier->mem_ctx;
-+ cb_data->cb = o->callback;
-+ cb_data->observer = o->observer;
-+ cb_data->data = o->data;
-+ cb_data->object = notifier->object;
-+ cb_data->notification = notification;
-+ cb_data->notification_data = notification_data;
-+ DWC_DEBUGC("Observer found %p for notification %s\n", o->observer, notification);
-+ DWC_WORKQ_SCHEDULE(manager->wq, cb_task, cb_data,
-+ "Notify callback from %p for Notification %s, to observer %p",
-+ cb_data->object, notification, cb_data->observer);
-+ }
-+ }
-+}
-+
-+#endif /* DWC_NOTIFYLIB */
---- /dev/null
-+++ b/drivers/usb/host/dwc_common_port/dwc_notifier.h
-@@ -0,0 +1,122 @@
-+
-+#ifndef __DWC_NOTIFIER_H__
-+#define __DWC_NOTIFIER_H__
-+
-+#ifdef __cplusplus
-+extern "C" {
-+#endif
-+
-+#include "dwc_os.h"
-+
-+/** @file
-+ *
-+ * A simple implementation of the Observer pattern. Any "module" can
-+ * register as an observer or notifier. The notion of "module" is abstract and
-+ * can mean anything used to identify either an observer or notifier. Usually
-+ * it will be a pointer to a data structure which contains some state, ie an
-+ * object.
-+ *
-+ * Before any notifiers can be added, the global notification manager must be
-+ * brought up with dwc_alloc_notification_manager().
-+ * dwc_free_notification_manager() will bring it down and free all resources.
-+ * These would typically be called upon module load and unload. The
-+ * notification manager is a single global instance that handles all registered
-+ * observable modules and observers so this should be done only once.
-+ *
-+ * A module can be observable by using Notifications to publicize some general
-+ * information about it's state or operation. It does not care who listens, or
-+ * even if anyone listens, or what they do with the information. The observable
-+ * modules do not need to know any information about it's observers or their
-+ * interface, or their state or data.
-+ *
-+ * Any module can register to emit Notifications. It should publish a list of
-+ * notifications that it can emit and their behavior, such as when they will get
-+ * triggered, and what information will be provided to the observer. Then it
-+ * should register itself as an observable module. See dwc_register_notifier().
-+ *
-+ * Any module can observe any observable, registered module, provided it has a
-+ * handle to the other module and knows what notifications to observe. See
-+ * dwc_add_observer().
-+ *
-+ * A function of type dwc_notifier_callback_t is called whenever a notification
-+ * is triggered with one or more observers observing it. This function is
-+ * called in it's own process so it may sleep or block if needed. It is
-+ * guaranteed to be called sometime after the notification has occurred and will
-+ * be called once per each time the notification is triggered. It will NOT be
-+ * called in the same process context used to trigger the notification.
-+ *
-+ * @section Limitiations
-+ *
-+ * Keep in mind that Notifications that can be triggered in rapid sucession may
-+ * schedule too many processes too handle. Be aware of this limitation when
-+ * designing to use notifications, and only add notifications for appropriate
-+ * observable information.
-+ *
-+ * Also Notification callbacks are not synchronous. If you need to synchronize
-+ * the behavior between module/observer you must use other means. And perhaps
-+ * that will mean Notifications are not the proper solution.
-+ */
-+
-+struct dwc_notifier;
-+typedef struct dwc_notifier dwc_notifier_t;
-+
-+/** The callback function must be of this type.
-+ *
-+ * @param object This is the object that is being observed.
-+ * @param notification This is the notification that was triggered.
-+ * @param observer This is the observer
-+ * @param notification_data This is notification-specific data that the notifier
-+ * has included in this notification. The value of this should be published in
-+ * the documentation of the observable module with the notifications.
-+ * @param user_data This is any custom data that the observer provided when
-+ * adding itself as an observer to the notification. */
-+typedef void (*dwc_notifier_callback_t)(void *object, char *notification, void *observer,
-+ void *notification_data, void *user_data);
-+
-+/** Brings up the notification manager. */
-+extern int dwc_alloc_notification_manager(void *mem_ctx, void *wkq_ctx);
-+/** Brings down the notification manager. */
-+extern void dwc_free_notification_manager(void);
-+
-+/** This function registers an observable module. A dwc_notifier_t object is
-+ * returned to the observable module. This is an opaque object that is used by
-+ * the observable module to trigger notifications. This object should only be
-+ * accessible to functions that are authorized to trigger notifications for this
-+ * module. Observers do not need this object. */
-+extern dwc_notifier_t *dwc_register_notifier(void *mem_ctx, void *object);
-+
-+/** This function unregisters an observable module. All observers have to be
-+ * removed prior to unregistration. */
-+extern void dwc_unregister_notifier(dwc_notifier_t *notifier);
-+
-+/** Add a module as an observer to the observable module. The observable module
-+ * needs to have previously registered with the notification manager.
-+ *
-+ * @param observer The observer module
-+ * @param object The module to observe
-+ * @param notification The notification to observe
-+ * @param callback The callback function to call
-+ * @param user_data Any additional user data to pass into the callback function */
-+extern int dwc_add_observer(void *observer, void *object, char *notification,
-+ dwc_notifier_callback_t callback, void *user_data);
-+
-+/** Removes the specified observer from all notifications that it is currently
-+ * observing. */
-+extern int dwc_remove_observer(void *observer);
-+
-+/** This function triggers a Notification. It should be called by the
-+ * observable module, or any module or library which the observable module
-+ * allows to trigger notification on it's behalf. Such as the dwc_cc_t.
-+ *
-+ * dwc_notify is a non-blocking function. Callbacks are scheduled called in
-+ * their own process context for each trigger. Callbacks can be blocking.
-+ * dwc_notify can be called from interrupt context if needed.
-+ *
-+ */
-+void dwc_notify(dwc_notifier_t *notifier, char *notification, void *notification_data);
-+
-+#ifdef __cplusplus
-+}
-+#endif
-+
-+#endif /* __DWC_NOTIFIER_H__ */
---- /dev/null
-+++ b/drivers/usb/host/dwc_common_port/dwc_os.h
-@@ -0,0 +1,1276 @@
-+/* =========================================================================
-+ * $File: //dwh/usb_iip/dev/software/dwc_common_port_2/dwc_os.h $
-+ * $Revision: #14 $
-+ * $Date: 2010/11/04 $
-+ * $Change: 1621695 $
-+ *
-+ * Synopsys Portability Library Software and documentation
-+ * (hereinafter, "Software") is an Unsupported proprietary work of
-+ * Synopsys, Inc. unless otherwise expressly agreed to in writing
-+ * between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product
-+ * under any End User Software License Agreement or Agreement for
-+ * Licensed Product with Synopsys or any supplement thereto. You are
-+ * permitted to use and redistribute this Software in source and binary
-+ * forms, with or without modification, provided that redistributions
-+ * of source code must retain this notice. You may not view, use,
-+ * disclose, copy or distribute this file or any information contained
-+ * herein except pursuant to this license grant from Synopsys. If you
-+ * do not agree with this notice, including the disclaimer below, then
-+ * you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS"
-+ * BASIS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
-+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
-+ * FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. IN NO EVENT SHALL
-+ * SYNOPSYS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY
-+ * OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
-+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
-+ * USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================= */
-+#ifndef _DWC_OS_H_
-+#define _DWC_OS_H_
-+
-+#ifdef __cplusplus
-+extern "C" {
-+#endif
-+
-+/** @file
-+ *
-+ * DWC portability library, low level os-wrapper functions
-+ *
-+ */
-+
-+/* These basic types need to be defined by some OS header file or custom header
-+ * file for your specific target architecture.
-+ *
-+ * uint8_t, int8_t, uint16_t, int16_t, uint32_t, int32_t, uint64_t, int64_t
-+ *
-+ * Any custom or alternate header file must be added and enabled here.
-+ */
-+
-+#ifdef DWC_LINUX
-+# include <linux/types.h>
-+# ifdef CONFIG_DEBUG_MUTEXES
-+# include <linux/mutex.h>
-+# endif
-+# include <linux/spinlock.h>
-+# include <linux/errno.h>
-+# include <stdarg.h>
-+#endif
-+
-+#if defined(DWC_FREEBSD) || defined(DWC_NETBSD)
-+# include <os_dep.h>
-+#endif
-+
-+
-+/** @name Primitive Types and Values */
-+
-+/** We define a boolean type for consistency. Can be either YES or NO */
-+typedef uint8_t dwc_bool_t;
-+#define YES 1
-+#define NO 0
-+
-+#ifdef DWC_LINUX
-+
-+/** @name Error Codes */
-+#define DWC_E_INVALID EINVAL
-+#define DWC_E_NO_MEMORY ENOMEM
-+#define DWC_E_NO_DEVICE ENODEV
-+#define DWC_E_NOT_SUPPORTED EOPNOTSUPP
-+#define DWC_E_TIMEOUT ETIMEDOUT
-+#define DWC_E_BUSY EBUSY
-+#define DWC_E_AGAIN EAGAIN
-+#define DWC_E_RESTART ERESTART
-+#define DWC_E_ABORT ECONNABORTED
-+#define DWC_E_SHUTDOWN ESHUTDOWN
-+#define DWC_E_NO_DATA ENODATA
-+#define DWC_E_DISCONNECT ECONNRESET
-+#define DWC_E_UNKNOWN EINVAL
-+#define DWC_E_NO_STREAM_RES ENOSR
-+#define DWC_E_COMMUNICATION ECOMM
-+#define DWC_E_OVERFLOW EOVERFLOW
-+#define DWC_E_PROTOCOL EPROTO
-+#define DWC_E_IN_PROGRESS EINPROGRESS
-+#define DWC_E_PIPE EPIPE
-+#define DWC_E_IO EIO
-+#define DWC_E_NO_SPACE ENOSPC
-+
-+#else
-+
-+/** @name Error Codes */
-+#define DWC_E_INVALID 1001
-+#define DWC_E_NO_MEMORY 1002
-+#define DWC_E_NO_DEVICE 1003
-+#define DWC_E_NOT_SUPPORTED 1004
-+#define DWC_E_TIMEOUT 1005
-+#define DWC_E_BUSY 1006
-+#define DWC_E_AGAIN 1007
-+#define DWC_E_RESTART 1008
-+#define DWC_E_ABORT 1009
-+#define DWC_E_SHUTDOWN 1010
-+#define DWC_E_NO_DATA 1011
-+#define DWC_E_DISCONNECT 2000
-+#define DWC_E_UNKNOWN 3000
-+#define DWC_E_NO_STREAM_RES 4001
-+#define DWC_E_COMMUNICATION 4002
-+#define DWC_E_OVERFLOW 4003
-+#define DWC_E_PROTOCOL 4004
-+#define DWC_E_IN_PROGRESS 4005
-+#define DWC_E_PIPE 4006
-+#define DWC_E_IO 4007
-+#define DWC_E_NO_SPACE 4008
-+
-+#endif
-+
-+
-+/** @name Tracing/Logging Functions
-+ *
-+ * These function provide the capability to add tracing, debugging, and error
-+ * messages, as well exceptions as assertions. The WUDEV uses these
-+ * extensively. These could be logged to the main console, the serial port, an
-+ * internal buffer, etc. These functions could also be no-op if they are too
-+ * expensive on your system. By default undefining the DEBUG macro already
-+ * no-ops some of these functions. */
-+
-+/** Returns non-zero if in interrupt context. */
-+extern dwc_bool_t DWC_IN_IRQ(void);
-+#define dwc_in_irq DWC_IN_IRQ
-+
-+/** Returns "IRQ" if DWC_IN_IRQ is true. */
-+static inline char *dwc_irq(void) {
-+ return DWC_IN_IRQ() ? "IRQ" : "";
-+}
-+
-+/** Returns non-zero if in bottom-half context. */
-+extern dwc_bool_t DWC_IN_BH(void);
-+#define dwc_in_bh DWC_IN_BH
-+
-+/** Returns "BH" if DWC_IN_BH is true. */
-+static inline char *dwc_bh(void) {
-+ return DWC_IN_BH() ? "BH" : "";
-+}
-+
-+/**
-+ * A vprintf() clone. Just call vprintf if you've got it.
-+ */
-+extern void DWC_VPRINTF(char *format, va_list args);
-+#define dwc_vprintf DWC_VPRINTF
-+
-+/**
-+ * A vsnprintf() clone. Just call vprintf if you've got it.
-+ */
-+extern int DWC_VSNPRINTF(char *str, int size, char *format, va_list args);
-+#define dwc_vsnprintf DWC_VSNPRINTF
-+
-+/**
-+ * printf() clone. Just call printf if you've go it.
-+ */
-+extern void DWC_PRINTF(char *format, ...)
-+/* This provides compiler level static checking of the parameters if you're
-+ * using GCC. */
-+#ifdef __GNUC__
-+ __attribute__ ((format(printf, 1, 2)));
-+#else
-+ ;
-+#endif
-+#define dwc_printf DWC_PRINTF
-+
-+/**
-+ * sprintf() clone. Just call sprintf if you've got it.
-+ */
-+extern int DWC_SPRINTF(char *string, char *format, ...)
-+#ifdef __GNUC__
-+ __attribute__ ((format(printf, 2, 3)));
-+#else
-+ ;
-+#endif
-+#define dwc_sprintf DWC_SPRINTF
-+
-+/**
-+ * snprintf() clone. Just call snprintf if you've got it.
-+ */
-+extern int DWC_SNPRINTF(char *string, int size, char *format, ...)
-+#ifdef __GNUC__
-+ __attribute__ ((format(printf, 3, 4)));
-+#else
-+ ;
-+#endif
-+#define dwc_snprintf DWC_SNPRINTF
-+
-+/**
-+ * Prints a WARNING message. On systems that don't differentiate between
-+ * warnings and regular log messages, just print it. Indicates that something
-+ * may be wrong with the driver. Works like printf().
-+ *
-+ * Use the DWC_WARN macro to call this function.
-+ */
-+extern void __DWC_WARN(char *format, ...)
-+#ifdef __GNUC__
-+ __attribute__ ((format(printf, 1, 2)));
-+#else
-+ ;
-+#endif
-+
-+/**
-+ * Prints an error message. On systems that don't differentiate between errors
-+ * and regular log messages, just print it. Indicates that something went wrong
-+ * with the driver. Works like printf().
-+ *
-+ * Use the DWC_ERROR macro to call this function.
-+ */
-+extern void __DWC_ERROR(char *format, ...)
-+#ifdef __GNUC__
-+ __attribute__ ((format(printf, 1, 2)));
-+#else
-+ ;
-+#endif
-+
-+/**
-+ * Prints an exception error message and takes some user-defined action such as
-+ * print out a backtrace or trigger a breakpoint. Indicates that something went
-+ * abnormally wrong with the driver such as programmer error, or other
-+ * exceptional condition. It should not be ignored so even on systems without
-+ * printing capability, some action should be taken to notify the developer of
-+ * it. Works like printf().
-+ */
-+extern void DWC_EXCEPTION(char *format, ...)
-+#ifdef __GNUC__
-+ __attribute__ ((format(printf, 1, 2)));
-+#else
-+ ;
-+#endif
-+#define dwc_exception DWC_EXCEPTION
-+
-+#ifndef DWC_OTG_DEBUG_LEV
-+#define DWC_OTG_DEBUG_LEV 0
-+#endif
-+
-+#ifdef DEBUG
-+/**
-+ * Prints out a debug message. Used for logging/trace messages.
-+ *
-+ * Use the DWC_DEBUG macro to call this function
-+ */
-+extern void __DWC_DEBUG(char *format, ...)
-+#ifdef __GNUC__
-+ __attribute__ ((format(printf, 1, 2)));
-+#else
-+ ;
-+#endif
-+#else
-+#define __DWC_DEBUG printk
-+#endif
-+
-+/**
-+ * Prints out a Debug message.
-+ */
-+#define DWC_DEBUG(_format, _args...) __DWC_DEBUG("DEBUG:%s:%s: " _format "\n", \
-+ __func__, dwc_irq(), ## _args)
-+#define dwc_debug DWC_DEBUG
-+/**
-+ * Prints out a Debug message if enabled at compile time.
-+ */
-+#if DWC_OTG_DEBUG_LEV > 0
-+#define DWC_DEBUGC(_format, _args...) DWC_DEBUG(_format, ##_args )
-+#else
-+#define DWC_DEBUGC(_format, _args...)
-+#endif
-+#define dwc_debugc DWC_DEBUGC
-+/**
-+ * Prints out an informative message.
-+ */
-+#define DWC_INFO(_format, _args...) DWC_PRINTF("INFO:%s: " _format "\n", \
-+ dwc_irq(), ## _args)
-+#define dwc_info DWC_INFO
-+/**
-+ * Prints out an informative message if enabled at compile time.
-+ */
-+#if DWC_OTG_DEBUG_LEV > 1
-+#define DWC_INFOC(_format, _args...) DWC_INFO(_format, ##_args )
-+#else
-+#define DWC_INFOC(_format, _args...)
-+#endif
-+#define dwc_infoc DWC_INFOC
-+/**
-+ * Prints out a warning message.
-+ */
-+#define DWC_WARN(_format, _args...) __DWC_WARN("WARN:%s:%s:%d: " _format "\n", \
-+ dwc_irq(), __func__, __LINE__, ## _args)
-+#define dwc_warn DWC_WARN
-+/**
-+ * Prints out an error message.
-+ */
-+#define DWC_ERROR(_format, _args...) __DWC_ERROR("ERROR:%s:%s:%d: " _format "\n", \
-+ dwc_irq(), __func__, __LINE__, ## _args)
-+#define dwc_error DWC_ERROR
-+
-+#define DWC_PROTO_ERROR(_format, _args...) __DWC_WARN("ERROR:%s:%s:%d: " _format "\n", \
-+ dwc_irq(), __func__, __LINE__, ## _args)
-+#define dwc_proto_error DWC_PROTO_ERROR
-+
-+#ifdef DEBUG
-+/** Prints out a exception error message if the _expr expression fails. Disabled
-+ * if DEBUG is not enabled. */
-+#define DWC_ASSERT(_expr, _format, _args...) do { \
-+ if (!(_expr)) { DWC_EXCEPTION("%s:%s:%d: " _format "\n", dwc_irq(), \
-+ __FILE__, __LINE__, ## _args); } \
-+ } while (0)
-+#else
-+#define DWC_ASSERT(_x...)
-+#endif
-+#define dwc_assert DWC_ASSERT
-+
-+
-+/** @name Byte Ordering
-+ * The following functions are for conversions between processor's byte ordering
-+ * and specific ordering you want.
-+ */
-+
-+/** Converts 32 bit data in CPU byte ordering to little endian. */
-+extern uint32_t DWC_CPU_TO_LE32(uint32_t *p);
-+#define dwc_cpu_to_le32 DWC_CPU_TO_LE32
-+
-+/** Converts 32 bit data in CPU byte orderint to big endian. */
-+extern uint32_t DWC_CPU_TO_BE32(uint32_t *p);
-+#define dwc_cpu_to_be32 DWC_CPU_TO_BE32
-+
-+/** Converts 32 bit little endian data to CPU byte ordering. */
-+extern uint32_t DWC_LE32_TO_CPU(uint32_t *p);
-+#define dwc_le32_to_cpu DWC_LE32_TO_CPU
-+
-+/** Converts 32 bit big endian data to CPU byte ordering. */
-+extern uint32_t DWC_BE32_TO_CPU(uint32_t *p);
-+#define dwc_be32_to_cpu DWC_BE32_TO_CPU
-+
-+/** Converts 16 bit data in CPU byte ordering to little endian. */
-+extern uint16_t DWC_CPU_TO_LE16(uint16_t *p);
-+#define dwc_cpu_to_le16 DWC_CPU_TO_LE16
-+
-+/** Converts 16 bit data in CPU byte orderint to big endian. */
-+extern uint16_t DWC_CPU_TO_BE16(uint16_t *p);
-+#define dwc_cpu_to_be16 DWC_CPU_TO_BE16
-+
-+/** Converts 16 bit little endian data to CPU byte ordering. */
-+extern uint16_t DWC_LE16_TO_CPU(uint16_t *p);
-+#define dwc_le16_to_cpu DWC_LE16_TO_CPU
-+
-+/** Converts 16 bit bi endian data to CPU byte ordering. */
-+extern uint16_t DWC_BE16_TO_CPU(uint16_t *p);
-+#define dwc_be16_to_cpu DWC_BE16_TO_CPU
-+
-+
-+/** @name Register Read/Write
-+ *
-+ * The following six functions should be implemented to read/write registers of
-+ * 32-bit and 64-bit sizes. All modules use this to read/write register values.
-+ * The reg value is a pointer to the register calculated from the void *base
-+ * variable passed into the driver when it is started. */
-+
-+#ifdef DWC_LINUX
-+/* Linux doesn't need any extra parameters for register read/write, so we
-+ * just throw away the IO context parameter.
-+ */
-+/** Reads the content of a 32-bit register. */
-+extern uint32_t DWC_READ_REG32(uint32_t volatile *reg);
-+#define dwc_read_reg32(_ctx_,_reg_) DWC_READ_REG32(_reg_)
-+
-+/** Reads the content of a 64-bit register. */
-+extern uint64_t DWC_READ_REG64(uint64_t volatile *reg);
-+#define dwc_read_reg64(_ctx_,_reg_) DWC_READ_REG64(_reg_)
-+
-+/** Writes to a 32-bit register. */
-+extern void DWC_WRITE_REG32(uint32_t volatile *reg, uint32_t value);
-+#define dwc_write_reg32(_ctx_,_reg_,_val_) DWC_WRITE_REG32(_reg_, _val_)
-+
-+/** Writes to a 64-bit register. */
-+extern void DWC_WRITE_REG64(uint64_t volatile *reg, uint64_t value);
-+#define dwc_write_reg64(_ctx_,_reg_,_val_) DWC_WRITE_REG64(_reg_, _val_)
-+
-+/**
-+ * Modify bit values in a register. Using the
-+ * algorithm: (reg_contents & ~clear_mask) | set_mask.
-+ */
-+extern void DWC_MODIFY_REG32(uint32_t volatile *reg, uint32_t clear_mask, uint32_t set_mask);
-+#define dwc_modify_reg32(_ctx_,_reg_,_cmsk_,_smsk_) DWC_MODIFY_REG32(_reg_,_cmsk_,_smsk_)
-+extern void DWC_MODIFY_REG64(uint64_t volatile *reg, uint64_t clear_mask, uint64_t set_mask);
-+#define dwc_modify_reg64(_ctx_,_reg_,_cmsk_,_smsk_) DWC_MODIFY_REG64(_reg_,_cmsk_,_smsk_)
-+
-+#endif /* DWC_LINUX */
-+
-+#if defined(DWC_FREEBSD) || defined(DWC_NETBSD)
-+typedef struct dwc_ioctx {
-+ struct device *dev;
-+ bus_space_tag_t iot;
-+ bus_space_handle_t ioh;
-+} dwc_ioctx_t;
-+
-+/** BSD needs two extra parameters for register read/write, so we pass
-+ * them in using the IO context parameter.
-+ */
-+/** Reads the content of a 32-bit register. */
-+extern uint32_t DWC_READ_REG32(void *io_ctx, uint32_t volatile *reg);
-+#define dwc_read_reg32 DWC_READ_REG32
-+
-+/** Reads the content of a 64-bit register. */
-+extern uint64_t DWC_READ_REG64(void *io_ctx, uint64_t volatile *reg);
-+#define dwc_read_reg64 DWC_READ_REG64
-+
-+/** Writes to a 32-bit register. */
-+extern void DWC_WRITE_REG32(void *io_ctx, uint32_t volatile *reg, uint32_t value);
-+#define dwc_write_reg32 DWC_WRITE_REG32
-+
-+/** Writes to a 64-bit register. */
-+extern void DWC_WRITE_REG64(void *io_ctx, uint64_t volatile *reg, uint64_t value);
-+#define dwc_write_reg64 DWC_WRITE_REG64
-+
-+/**
-+ * Modify bit values in a register. Using the
-+ * algorithm: (reg_contents & ~clear_mask) | set_mask.
-+ */
-+extern void DWC_MODIFY_REG32(void *io_ctx, uint32_t volatile *reg, uint32_t clear_mask, uint32_t set_mask);
-+#define dwc_modify_reg32 DWC_MODIFY_REG32
-+extern void DWC_MODIFY_REG64(void *io_ctx, uint64_t volatile *reg, uint64_t clear_mask, uint64_t set_mask);
-+#define dwc_modify_reg64 DWC_MODIFY_REG64
-+
-+#endif /* DWC_FREEBSD || DWC_NETBSD */
-+
-+/** @cond */
-+
-+/** @name Some convenience MACROS used internally. Define DWC_DEBUG_REGS to log the
-+ * register writes. */
-+
-+#ifdef DWC_LINUX
-+
-+# ifdef DWC_DEBUG_REGS
-+
-+#define dwc_define_read_write_reg_n(_reg,_container_type) \
-+static inline uint32_t dwc_read_##_reg##_n(_container_type *container, int num) { \
-+ return DWC_READ_REG32(&container->regs->_reg[num]); \
-+} \
-+static inline void dwc_write_##_reg##_n(_container_type *container, int num, uint32_t data) { \
-+ DWC_DEBUG("WRITING %8s[%d]: %p: %08x", #_reg, num, \
-+ &(((uint32_t*)container->regs->_reg)[num]), data); \
-+ DWC_WRITE_REG32(&(((uint32_t*)container->regs->_reg)[num]), data); \
-+}
-+
-+#define dwc_define_read_write_reg(_reg,_container_type) \
-+static inline uint32_t dwc_read_##_reg(_container_type *container) { \
-+ return DWC_READ_REG32(&container->regs->_reg); \
-+} \
-+static inline void dwc_write_##_reg(_container_type *container, uint32_t data) { \
-+ DWC_DEBUG("WRITING %11s: %p: %08x", #_reg, &container->regs->_reg, data); \
-+ DWC_WRITE_REG32(&container->regs->_reg, data); \
-+}
-+
-+# else /* DWC_DEBUG_REGS */
-+
-+#define dwc_define_read_write_reg_n(_reg,_container_type) \
-+static inline uint32_t dwc_read_##_reg##_n(_container_type *container, int num) { \
-+ return DWC_READ_REG32(&container->regs->_reg[num]); \
-+} \
-+static inline void dwc_write_##_reg##_n(_container_type *container, int num, uint32_t data) { \
-+ DWC_WRITE_REG32(&(((uint32_t*)container->regs->_reg)[num]), data); \
-+}
-+
-+#define dwc_define_read_write_reg(_reg,_container_type) \
-+static inline uint32_t dwc_read_##_reg(_container_type *container) { \
-+ return DWC_READ_REG32(&container->regs->_reg); \
-+} \
-+static inline void dwc_write_##_reg(_container_type *container, uint32_t data) { \
-+ DWC_WRITE_REG32(&container->regs->_reg, data); \
-+}
-+
-+# endif /* DWC_DEBUG_REGS */
-+
-+#endif /* DWC_LINUX */
-+
-+#if defined(DWC_FREEBSD) || defined(DWC_NETBSD)
-+
-+# ifdef DWC_DEBUG_REGS
-+
-+#define dwc_define_read_write_reg_n(_reg,_container_type) \
-+static inline uint32_t dwc_read_##_reg##_n(void *io_ctx, _container_type *container, int num) { \
-+ return DWC_READ_REG32(io_ctx, &container->regs->_reg[num]); \
-+} \
-+static inline void dwc_write_##_reg##_n(void *io_ctx, _container_type *container, int num, uint32_t data) { \
-+ DWC_DEBUG("WRITING %8s[%d]: %p: %08x", #_reg, num, \
-+ &(((uint32_t*)container->regs->_reg)[num]), data); \
-+ DWC_WRITE_REG32(io_ctx, &(((uint32_t*)container->regs->_reg)[num]), data); \
-+}
-+
-+#define dwc_define_read_write_reg(_reg,_container_type) \
-+static inline uint32_t dwc_read_##_reg(void *io_ctx, _container_type *container) { \
-+ return DWC_READ_REG32(io_ctx, &container->regs->_reg); \
-+} \
-+static inline void dwc_write_##_reg(void *io_ctx, _container_type *container, uint32_t data) { \
-+ DWC_DEBUG("WRITING %11s: %p: %08x", #_reg, &container->regs->_reg, data); \
-+ DWC_WRITE_REG32(io_ctx, &container->regs->_reg, data); \
-+}
-+
-+# else /* DWC_DEBUG_REGS */
-+
-+#define dwc_define_read_write_reg_n(_reg,_container_type) \
-+static inline uint32_t dwc_read_##_reg##_n(void *io_ctx, _container_type *container, int num) { \
-+ return DWC_READ_REG32(io_ctx, &container->regs->_reg[num]); \
-+} \
-+static inline void dwc_write_##_reg##_n(void *io_ctx, _container_type *container, int num, uint32_t data) { \
-+ DWC_WRITE_REG32(io_ctx, &(((uint32_t*)container->regs->_reg)[num]), data); \
-+}
-+
-+#define dwc_define_read_write_reg(_reg,_container_type) \
-+static inline uint32_t dwc_read_##_reg(void *io_ctx, _container_type *container) { \
-+ return DWC_READ_REG32(io_ctx, &container->regs->_reg); \
-+} \
-+static inline void dwc_write_##_reg(void *io_ctx, _container_type *container, uint32_t data) { \
-+ DWC_WRITE_REG32(io_ctx, &container->regs->_reg, data); \
-+}
-+
-+# endif /* DWC_DEBUG_REGS */
-+
-+#endif /* DWC_FREEBSD || DWC_NETBSD */
-+
-+/** @endcond */
-+
-+
-+#ifdef DWC_CRYPTOLIB
-+/** @name Crypto Functions
-+ *
-+ * These are the low-level cryptographic functions used by the driver. */
-+
-+/** Perform AES CBC */
-+extern int DWC_AES_CBC(uint8_t *message, uint32_t messagelen, uint8_t *key, uint32_t keylen, uint8_t iv[16], uint8_t *out);
-+#define dwc_aes_cbc DWC_AES_CBC
-+
-+/** Fill the provided buffer with random bytes. These should be cryptographic grade random numbers. */
-+extern void DWC_RANDOM_BYTES(uint8_t *buffer, uint32_t length);
-+#define dwc_random_bytes DWC_RANDOM_BYTES
-+
-+/** Perform the SHA-256 hash function */
-+extern int DWC_SHA256(uint8_t *message, uint32_t len, uint8_t *out);
-+#define dwc_sha256 DWC_SHA256
-+
-+/** Calculated the HMAC-SHA256 */
-+extern int DWC_HMAC_SHA256(uint8_t *message, uint32_t messagelen, uint8_t *key, uint32_t keylen, uint8_t *out);
-+#define dwc_hmac_sha256 DWC_HMAC_SHA256
-+
-+#endif /* DWC_CRYPTOLIB */
-+
-+
-+/** @name Memory Allocation
-+ *
-+ * These function provide access to memory allocation. There are only 2 DMA
-+ * functions and 3 Regular memory functions that need to be implemented. None
-+ * of the memory debugging routines need to be implemented. The allocation
-+ * routines all ZERO the contents of the memory.
-+ *
-+ * Defining DWC_DEBUG_MEMORY turns on memory debugging and statistic gathering.
-+ * This checks for memory leaks, keeping track of alloc/free pairs. It also
-+ * keeps track of how much memory the driver is using at any given time. */
-+
-+#define DWC_PAGE_SIZE 4096
-+#define DWC_PAGE_OFFSET(addr) (((uint32_t)addr) & 0xfff)
-+#define DWC_PAGE_ALIGNED(addr) ((((uint32_t)addr) & 0xfff) == 0)
-+
-+#define DWC_INVALID_DMA_ADDR 0x0
-+
-+#ifdef DWC_LINUX
-+/** Type for a DMA address */
-+typedef dma_addr_t dwc_dma_t;
-+#endif
-+
-+#if defined(DWC_FREEBSD) || defined(DWC_NETBSD)
-+typedef bus_addr_t dwc_dma_t;
-+#endif
-+
-+#ifdef DWC_FREEBSD
-+typedef struct dwc_dmactx {
-+ struct device *dev;
-+ bus_dma_tag_t dma_tag;
-+ bus_dmamap_t dma_map;
-+ bus_addr_t dma_paddr;
-+ void *dma_vaddr;
-+} dwc_dmactx_t;
-+#endif
-+
-+#ifdef DWC_NETBSD
-+typedef struct dwc_dmactx {
-+ struct device *dev;
-+ bus_dma_tag_t dma_tag;
-+ bus_dmamap_t dma_map;
-+ bus_dma_segment_t segs[1];
-+ int nsegs;
-+ bus_addr_t dma_paddr;
-+ void *dma_vaddr;
-+} dwc_dmactx_t;
-+#endif
-+
-+/* @todo these functions will be added in the future */
-+#if 0
-+/**
-+ * Creates a DMA pool from which you can allocate DMA buffers. Buffers
-+ * allocated from this pool will be guaranteed to meet the size, alignment, and
-+ * boundary requirements specified.
-+ *
-+ * @param[in] size Specifies the size of the buffers that will be allocated from
-+ * this pool.
-+ * @param[in] align Specifies the byte alignment requirements of the buffers
-+ * allocated from this pool. Must be a power of 2.
-+ * @param[in] boundary Specifies the N-byte boundary that buffers allocated from
-+ * this pool must not cross.
-+ *
-+ * @returns A pointer to an internal opaque structure which is not to be
-+ * accessed outside of these library functions. Use this handle to specify
-+ * which pools to allocate/free DMA buffers from and also to destroy the pool,
-+ * when you are done with it.
-+ */
-+extern dwc_pool_t *DWC_DMA_POOL_CREATE(uint32_t size, uint32_t align, uint32_t boundary);
-+
-+/**
-+ * Destroy a DMA pool. All buffers allocated from that pool must be freed first.
-+ */
-+extern void DWC_DMA_POOL_DESTROY(dwc_pool_t *pool);
-+
-+/**
-+ * Allocate a buffer from the specified DMA pool and zeros its contents.
-+ */
-+extern void *DWC_DMA_POOL_ALLOC(dwc_pool_t *pool, uint64_t *dma_addr);
-+
-+/**
-+ * Free a previously allocated buffer from the DMA pool.
-+ */
-+extern void DWC_DMA_POOL_FREE(dwc_pool_t *pool, void *vaddr, void *daddr);
-+#endif
-+
-+/** Allocates a DMA capable buffer and zeroes its contents. */
-+extern void *__DWC_DMA_ALLOC(void *dma_ctx, uint32_t size, dwc_dma_t *dma_addr);
-+
-+/** Allocates a DMA capable buffer and zeroes its contents in atomic contest */
-+extern void *__DWC_DMA_ALLOC_ATOMIC(void *dma_ctx, uint32_t size, dwc_dma_t *dma_addr);
-+
-+/** Frees a previously allocated buffer. */
-+extern void __DWC_DMA_FREE(void *dma_ctx, uint32_t size, void *virt_addr, dwc_dma_t dma_addr);
-+
-+/** Allocates a block of memory and zeroes its contents. */
-+extern void *__DWC_ALLOC(void *mem_ctx, uint32_t size);
-+
-+/** Allocates a block of memory and zeroes its contents, in an atomic manner
-+ * which can be used inside interrupt context. The size should be sufficiently
-+ * small, a few KB at most, such that failures are not likely to occur. Can just call
-+ * __DWC_ALLOC if it is atomic. */
-+extern void *__DWC_ALLOC_ATOMIC(void *mem_ctx, uint32_t size);
-+
-+/** Frees a previously allocated buffer. */
-+extern void __DWC_FREE(void *mem_ctx, void *addr);
-+
-+#ifndef DWC_DEBUG_MEMORY
-+
-+#define DWC_ALLOC(_size_) __DWC_ALLOC(NULL, _size_)
-+#define DWC_ALLOC_ATOMIC(_size_) __DWC_ALLOC_ATOMIC(NULL, _size_)
-+#define DWC_FREE(_addr_) __DWC_FREE(NULL, _addr_)
-+
-+# ifdef DWC_LINUX
-+#define DWC_DMA_ALLOC(_size_,_dma_) __DWC_DMA_ALLOC(NULL, _size_, _dma_)
-+#define DWC_DMA_ALLOC_ATOMIC(_size_,_dma_) __DWC_DMA_ALLOC_ATOMIC(NULL, _size_,_dma_)
-+#define DWC_DMA_FREE(_size_,_virt_,_dma_) __DWC_DMA_FREE(NULL, _size_, _virt_, _dma_)
-+# endif
-+
-+# if defined(DWC_FREEBSD) || defined(DWC_NETBSD)
-+#define DWC_DMA_ALLOC __DWC_DMA_ALLOC
-+#define DWC_DMA_FREE __DWC_DMA_FREE
-+# endif
-+extern void *dwc_dma_alloc_atomic_debug(uint32_t size, dwc_dma_t *dma_addr, char const *func, int line);
-+
-+#else /* DWC_DEBUG_MEMORY */
-+
-+extern void *dwc_alloc_debug(void *mem_ctx, uint32_t size, char const *func, int line);
-+extern void *dwc_alloc_atomic_debug(void *mem_ctx, uint32_t size, char const *func, int line);
-+extern void dwc_free_debug(void *mem_ctx, void *addr, char const *func, int line);
-+extern void *dwc_dma_alloc_debug(void *dma_ctx, uint32_t size, dwc_dma_t *dma_addr,
-+ char const *func, int line);
-+extern void *dwc_dma_alloc_atomic_debug(void *dma_ctx, uint32_t size, dwc_dma_t *dma_addr,
-+ char const *func, int line);
-+extern void dwc_dma_free_debug(void *dma_ctx, uint32_t size, void *virt_addr,
-+ dwc_dma_t dma_addr, char const *func, int line);
-+
-+extern int dwc_memory_debug_start(void *mem_ctx);
-+extern void dwc_memory_debug_stop(void);
-+extern void dwc_memory_debug_report(void);
-+
-+#define DWC_ALLOC(_size_) dwc_alloc_debug(NULL, _size_, __func__, __LINE__)
-+#define DWC_ALLOC_ATOMIC(_size_) dwc_alloc_atomic_debug(NULL, _size_, \
-+ __func__, __LINE__)
-+#define DWC_FREE(_addr_) dwc_free_debug(NULL, _addr_, __func__, __LINE__)
-+
-+# ifdef DWC_LINUX
-+#define DWC_DMA_ALLOC(_size_,_dma_) dwc_dma_alloc_debug(NULL, _size_, \
-+ _dma_, __func__, __LINE__)
-+#define DWC_DMA_ALLOC_ATOMIC(_size_,_dma_) dwc_dma_alloc_atomic_debug(NULL, _size_, \
-+ _dma_, __func__, __LINE__)
-+#define DWC_DMA_FREE(_size_,_virt_,_dma_) dwc_dma_free_debug(NULL, _size_, \
-+ _virt_, _dma_, __func__, __LINE__)
-+# endif
-+
-+# if defined(DWC_FREEBSD) || defined(DWC_NETBSD)
-+#define DWC_DMA_ALLOC(_ctx_,_size_,_dma_) dwc_dma_alloc_debug(_ctx_, _size_, \
-+ _dma_, __func__, __LINE__)
-+#define DWC_DMA_FREE(_ctx_,_size_,_virt_,_dma_) dwc_dma_free_debug(_ctx_, _size_, \
-+ _virt_, _dma_, __func__, __LINE__)
-+# endif
-+
-+#endif /* DWC_DEBUG_MEMORY */
-+
-+#define dwc_alloc(_ctx_,_size_) DWC_ALLOC(_size_)
-+#define dwc_alloc_atomic(_ctx_,_size_) DWC_ALLOC_ATOMIC(_size_)
-+#define dwc_free(_ctx_,_addr_) DWC_FREE(_addr_)
-+
-+#ifdef DWC_LINUX
-+/* Linux doesn't need any extra parameters for DMA buffer allocation, so we
-+ * just throw away the DMA context parameter.
-+ */
-+#define dwc_dma_alloc(_ctx_,_size_,_dma_) DWC_DMA_ALLOC(_size_, _dma_)
-+#define dwc_dma_alloc_atomic(_ctx_,_size_,_dma_) DWC_DMA_ALLOC_ATOMIC(_size_, _dma_)
-+#define dwc_dma_free(_ctx_,_size_,_virt_,_dma_) DWC_DMA_FREE(_size_, _virt_, _dma_)
-+#endif
-+
-+#if defined(DWC_FREEBSD) || defined(DWC_NETBSD)
-+/** BSD needs several extra parameters for DMA buffer allocation, so we pass
-+ * them in using the DMA context parameter.
-+ */
-+#define dwc_dma_alloc DWC_DMA_ALLOC
-+#define dwc_dma_free DWC_DMA_FREE
-+#endif
-+
-+
-+/** @name Memory and String Processing */
-+
-+/** memset() clone */
-+extern void *DWC_MEMSET(void *dest, uint8_t byte, uint32_t size);
-+#define dwc_memset DWC_MEMSET
-+
-+/** memcpy() clone */
-+extern void *DWC_MEMCPY(void *dest, void const *src, uint32_t size);
-+#define dwc_memcpy DWC_MEMCPY
-+
-+/** memmove() clone */
-+extern void *DWC_MEMMOVE(void *dest, void *src, uint32_t size);
-+#define dwc_memmove DWC_MEMMOVE
-+
-+/** memcmp() clone */
-+extern int DWC_MEMCMP(void *m1, void *m2, uint32_t size);
-+#define dwc_memcmp DWC_MEMCMP
-+
-+/** strcmp() clone */
-+extern int DWC_STRCMP(void *s1, void *s2);
-+#define dwc_strcmp DWC_STRCMP
-+
-+/** strncmp() clone */
-+extern int DWC_STRNCMP(void *s1, void *s2, uint32_t size);
-+#define dwc_strncmp DWC_STRNCMP
-+
-+/** strlen() clone, for NULL terminated ASCII strings */
-+extern int DWC_STRLEN(char const *str);
-+#define dwc_strlen DWC_STRLEN
-+
-+/** strcpy() clone, for NULL terminated ASCII strings */
-+extern char *DWC_STRCPY(char *to, const char *from);
-+#define dwc_strcpy DWC_STRCPY
-+
-+/** strdup() clone. If you wish to use memory allocation debugging, this
-+ * implementation of strdup should use the DWC_* memory routines instead of
-+ * calling a predefined strdup. Otherwise the memory allocated by this routine
-+ * will not be seen by the debugging routines. */
-+extern char *DWC_STRDUP(char const *str);
-+#define dwc_strdup(_ctx_,_str_) DWC_STRDUP(_str_)
-+
-+/** NOT an atoi() clone. Read the description carefully. Returns an integer
-+ * converted from the string str in base 10 unless the string begins with a "0x"
-+ * in which case it is base 16. String must be a NULL terminated sequence of
-+ * ASCII characters and may optionally begin with whitespace, a + or -, and a
-+ * "0x" prefix if base 16. The remaining characters must be valid digits for
-+ * the number and end with a NULL character. If any invalid characters are
-+ * encountered or it returns with a negative error code and the results of the
-+ * conversion are undefined. On sucess it returns 0. Overflow conditions are
-+ * undefined. An example implementation using atoi() can be referenced from the
-+ * Linux implementation. */
-+extern int DWC_ATOI(const char *str, int32_t *value);
-+#define dwc_atoi DWC_ATOI
-+
-+/** Same as above but for unsigned. */
-+extern int DWC_ATOUI(const char *str, uint32_t *value);
-+#define dwc_atoui DWC_ATOUI
-+
-+#ifdef DWC_UTFLIB
-+/** This routine returns a UTF16LE unicode encoded string from a UTF8 string. */
-+extern int DWC_UTF8_TO_UTF16LE(uint8_t const *utf8string, uint16_t *utf16string, unsigned len);
-+#define dwc_utf8_to_utf16le DWC_UTF8_TO_UTF16LE
-+#endif
-+
-+
-+/** @name Wait queues
-+ *
-+ * Wait queues provide a means of synchronizing between threads or processes. A
-+ * process can block on a waitq if some condition is not true, waiting for it to
-+ * become true. When the waitq is triggered all waiting process will get
-+ * unblocked and the condition will be check again. Waitqs should be triggered
-+ * every time a condition can potentially change.*/
-+struct dwc_waitq;
-+
-+/** Type for a waitq */
-+typedef struct dwc_waitq dwc_waitq_t;
-+
-+/** The type of waitq condition callback function. This is called every time
-+ * condition is evaluated. */
-+typedef int (*dwc_waitq_condition_t)(void *data);
-+
-+/** Allocate a waitq */
-+extern dwc_waitq_t *DWC_WAITQ_ALLOC(void);
-+#define dwc_waitq_alloc(_ctx_) DWC_WAITQ_ALLOC()
-+
-+/** Free a waitq */
-+extern void DWC_WAITQ_FREE(dwc_waitq_t *wq);
-+#define dwc_waitq_free DWC_WAITQ_FREE
-+
-+/** Check the condition and if it is false, block on the waitq. When unblocked, check the
-+ * condition again. The function returns when the condition becomes true. The return value
-+ * is 0 on condition true, DWC_WAITQ_ABORTED on abort or killed, or DWC_WAITQ_UNKNOWN on error. */
-+extern int32_t DWC_WAITQ_WAIT(dwc_waitq_t *wq, dwc_waitq_condition_t cond, void *data);
-+#define dwc_waitq_wait DWC_WAITQ_WAIT
-+
-+/** Check the condition and if it is false, block on the waitq. When unblocked,
-+ * check the condition again. The function returns when the condition become
-+ * true or the timeout has passed. The return value is 0 on condition true or
-+ * DWC_TIMED_OUT on timeout, or DWC_WAITQ_ABORTED, or DWC_WAITQ_UNKNOWN on
-+ * error. */
-+extern int32_t DWC_WAITQ_WAIT_TIMEOUT(dwc_waitq_t *wq, dwc_waitq_condition_t cond,
-+ void *data, int32_t msecs);
-+#define dwc_waitq_wait_timeout DWC_WAITQ_WAIT_TIMEOUT
-+
-+/** Trigger a waitq, unblocking all processes. This should be called whenever a condition
-+ * has potentially changed. */
-+extern void DWC_WAITQ_TRIGGER(dwc_waitq_t *wq);
-+#define dwc_waitq_trigger DWC_WAITQ_TRIGGER
-+
-+/** Unblock all processes waiting on the waitq with an ABORTED result. */
-+extern void DWC_WAITQ_ABORT(dwc_waitq_t *wq);
-+#define dwc_waitq_abort DWC_WAITQ_ABORT
-+
-+
-+/** @name Threads
-+ *
-+ * A thread must be explicitly stopped. It must check DWC_THREAD_SHOULD_STOP
-+ * whenever it is woken up, and then return. The DWC_THREAD_STOP function
-+ * returns the value from the thread.
-+ */
-+
-+struct dwc_thread;
-+
-+/** Type for a thread */
-+typedef struct dwc_thread dwc_thread_t;
-+
-+/** The thread function */
-+typedef int (*dwc_thread_function_t)(void *data);
-+
-+/** Create a thread and start it running the thread_function. Returns a handle
-+ * to the thread */
-+extern dwc_thread_t *DWC_THREAD_RUN(dwc_thread_function_t func, char *name, void *data);
-+#define dwc_thread_run(_ctx_,_func_,_name_,_data_) DWC_THREAD_RUN(_func_, _name_, _data_)
-+
-+/** Stops a thread. Return the value returned by the thread. Or will return
-+ * DWC_ABORT if the thread never started. */
-+extern int DWC_THREAD_STOP(dwc_thread_t *thread);
-+#define dwc_thread_stop DWC_THREAD_STOP
-+
-+/** Signifies to the thread that it must stop. */
-+#ifdef DWC_LINUX
-+/* Linux doesn't need any parameters for kthread_should_stop() */
-+extern dwc_bool_t DWC_THREAD_SHOULD_STOP(void);
-+#define dwc_thread_should_stop(_thrd_) DWC_THREAD_SHOULD_STOP()
-+
-+/* No thread_exit function in Linux */
-+#define dwc_thread_exit(_thrd_)
-+#endif
-+
-+#if defined(DWC_FREEBSD) || defined(DWC_NETBSD)
-+/** BSD needs the thread pointer for kthread_suspend_check() */
-+extern dwc_bool_t DWC_THREAD_SHOULD_STOP(dwc_thread_t *thread);
-+#define dwc_thread_should_stop DWC_THREAD_SHOULD_STOP
-+
-+/** The thread must call this to exit. */
-+extern void DWC_THREAD_EXIT(dwc_thread_t *thread);
-+#define dwc_thread_exit DWC_THREAD_EXIT
-+#endif
-+
-+
-+/** @name Work queues
-+ *
-+ * Workqs are used to queue a callback function to be called at some later time,
-+ * in another thread. */
-+struct dwc_workq;
-+
-+/** Type for a workq */
-+typedef struct dwc_workq dwc_workq_t;
-+
-+/** The type of the callback function to be called. */
-+typedef void (*dwc_work_callback_t)(void *data);
-+
-+/** Allocate a workq */
-+extern dwc_workq_t *DWC_WORKQ_ALLOC(char *name);
-+#define dwc_workq_alloc(_ctx_,_name_) DWC_WORKQ_ALLOC(_name_)
-+
-+/** Free a workq. All work must be completed before being freed. */
-+extern void DWC_WORKQ_FREE(dwc_workq_t *workq);
-+#define dwc_workq_free DWC_WORKQ_FREE
-+
-+/** Schedule a callback on the workq, passing in data. The function will be
-+ * scheduled at some later time. */
-+extern void DWC_WORKQ_SCHEDULE(dwc_workq_t *workq, dwc_work_callback_t cb,
-+ void *data, char *format, ...)
-+#ifdef __GNUC__
-+ __attribute__ ((format(printf, 4, 5)));
-+#else
-+ ;
-+#endif
-+#define dwc_workq_schedule DWC_WORKQ_SCHEDULE
-+
-+/** Schedule a callback on the workq, that will be called until at least
-+ * given number miliseconds have passed. */
-+extern void DWC_WORKQ_SCHEDULE_DELAYED(dwc_workq_t *workq, dwc_work_callback_t cb,
-+ void *data, uint32_t time, char *format, ...)
-+#ifdef __GNUC__
-+ __attribute__ ((format(printf, 5, 6)));
-+#else
-+ ;
-+#endif
-+#define dwc_workq_schedule_delayed DWC_WORKQ_SCHEDULE_DELAYED
-+
-+/** The number of processes in the workq */
-+extern int DWC_WORKQ_PENDING(dwc_workq_t *workq);
-+#define dwc_workq_pending DWC_WORKQ_PENDING
-+
-+/** Blocks until all the work in the workq is complete or timed out. Returns <
-+ * 0 on timeout. */
-+extern int DWC_WORKQ_WAIT_WORK_DONE(dwc_workq_t *workq, int timeout);
-+#define dwc_workq_wait_work_done DWC_WORKQ_WAIT_WORK_DONE
-+
-+
-+/** @name Tasklets
-+ *
-+ */
-+struct dwc_tasklet;
-+
-+/** Type for a tasklet */
-+typedef struct dwc_tasklet dwc_tasklet_t;
-+
-+/** The type of the callback function to be called */
-+typedef void (*dwc_tasklet_callback_t)(void *data);
-+
-+/** Allocates a tasklet */
-+extern dwc_tasklet_t *DWC_TASK_ALLOC(char *name, dwc_tasklet_callback_t cb, void *data);
-+#define dwc_task_alloc(_ctx_,_name_,_cb_,_data_) DWC_TASK_ALLOC(_name_, _cb_, _data_)
-+
-+/** Frees a tasklet */
-+extern void DWC_TASK_FREE(dwc_tasklet_t *task);
-+#define dwc_task_free DWC_TASK_FREE
-+
-+/** Schedules a tasklet to run */
-+extern void DWC_TASK_SCHEDULE(dwc_tasklet_t *task);
-+#define dwc_task_schedule DWC_TASK_SCHEDULE
-+
-+extern void DWC_TASK_HI_SCHEDULE(dwc_tasklet_t *task);
-+#define dwc_task_hi_schedule DWC_TASK_HI_SCHEDULE
-+
-+/** @name Timer
-+ *
-+ * Callbacks must be small and atomic.
-+ */
-+struct dwc_timer;
-+
-+/** Type for a timer */
-+typedef struct dwc_timer dwc_timer_t;
-+
-+/** The type of the callback function to be called */
-+typedef void (*dwc_timer_callback_t)(void *data);
-+
-+/** Allocates a timer */
-+extern dwc_timer_t *DWC_TIMER_ALLOC(char *name, dwc_timer_callback_t cb, void *data);
-+#define dwc_timer_alloc(_ctx_,_name_,_cb_,_data_) DWC_TIMER_ALLOC(_name_,_cb_,_data_)
-+
-+/** Frees a timer */
-+extern void DWC_TIMER_FREE(dwc_timer_t *timer);
-+#define dwc_timer_free DWC_TIMER_FREE
-+
-+/** Schedules the timer to run at time ms from now. And will repeat at every
-+ * repeat_interval msec therafter
-+ *
-+ * Modifies a timer that is still awaiting execution to a new expiration time.
-+ * The mod_time is added to the old time. */
-+extern void DWC_TIMER_SCHEDULE(dwc_timer_t *timer, uint32_t time);
-+#define dwc_timer_schedule DWC_TIMER_SCHEDULE
-+
-+/** Disables the timer from execution. */
-+extern void DWC_TIMER_CANCEL(dwc_timer_t *timer);
-+#define dwc_timer_cancel DWC_TIMER_CANCEL
-+
-+
-+/** @name Spinlocks
-+ *
-+ * These locks are used when the work between the lock/unlock is atomic and
-+ * short. Interrupts are also disabled during the lock/unlock and thus they are
-+ * suitable to lock between interrupt/non-interrupt context. They also lock
-+ * between processes if you have multiple CPUs or Preemption. If you don't have
-+ * multiple CPUS or Preemption, then the you can simply implement the
-+ * DWC_SPINLOCK and DWC_SPINUNLOCK to disable and enable interrupts. Because
-+ * the work between the lock/unlock is atomic, the process context will never
-+ * change, and so you never have to lock between processes. */
-+
-+struct dwc_spinlock;
-+
-+/** Type for a spinlock */
-+typedef struct dwc_spinlock dwc_spinlock_t;
-+
-+/** Type for the 'flags' argument to spinlock funtions */
-+typedef unsigned long dwc_irqflags_t;
-+
-+/** Returns an initialized lock variable. This function should allocate and
-+ * initialize the OS-specific data structure used for locking. This data
-+ * structure is to be used for the DWC_LOCK and DWC_UNLOCK functions and should
-+ * be freed by the DWC_FREE_LOCK when it is no longer used.
-+ *
-+ * For Linux Spinlock Debugging make it macro because the debugging routines use
-+ * the symbol name to determine recursive locking. Using a wrapper function
-+ * makes it falsely think recursive locking occurs. */
-+#if defined(DWC_LINUX) && defined(CONFIG_DEBUG_SPINLOCK)
-+#define DWC_SPINLOCK_ALLOC_LINUX_DEBUG(lock) ({ \
-+ lock = DWC_ALLOC(sizeof(spinlock_t)); \
-+ if (lock) { \
-+ spin_lock_init((spinlock_t *)lock); \
-+ } \
-+})
-+#else
-+extern dwc_spinlock_t *DWC_SPINLOCK_ALLOC(void);
-+#define dwc_spinlock_alloc(_ctx_) DWC_SPINLOCK_ALLOC()
-+#endif
-+
-+/** Frees an initialized lock variable. */
-+extern void DWC_SPINLOCK_FREE(dwc_spinlock_t *lock);
-+#define dwc_spinlock_free(_ctx_,_lock_) DWC_SPINLOCK_FREE(_lock_)
-+
-+/** Disables interrupts and blocks until it acquires the lock.
-+ *
-+ * @param lock Pointer to the spinlock.
-+ * @param flags Unsigned long for irq flags storage.
-+ */
-+extern void DWC_SPINLOCK_IRQSAVE(dwc_spinlock_t *lock, dwc_irqflags_t *flags);
-+#define dwc_spinlock_irqsave DWC_SPINLOCK_IRQSAVE
-+
-+/** Re-enables the interrupt and releases the lock.
-+ *
-+ * @param lock Pointer to the spinlock.
-+ * @param flags Unsigned long for irq flags storage. Must be the same as was
-+ * passed into DWC_LOCK.
-+ */
-+extern void DWC_SPINUNLOCK_IRQRESTORE(dwc_spinlock_t *lock, dwc_irqflags_t flags);
-+#define dwc_spinunlock_irqrestore DWC_SPINUNLOCK_IRQRESTORE
-+
-+/** Blocks until it acquires the lock.
-+ *
-+ * @param lock Pointer to the spinlock.
-+ */
-+extern void DWC_SPINLOCK(dwc_spinlock_t *lock);
-+#define dwc_spinlock DWC_SPINLOCK
-+
-+/** Releases the lock.
-+ *
-+ * @param lock Pointer to the spinlock.
-+ */
-+extern void DWC_SPINUNLOCK(dwc_spinlock_t *lock);
-+#define dwc_spinunlock DWC_SPINUNLOCK
-+
-+
-+/** @name Mutexes
-+ *
-+ * Unlike spinlocks Mutexes lock only between processes and the work between the
-+ * lock/unlock CAN block, therefore it CANNOT be called from interrupt context.
-+ */
-+
-+struct dwc_mutex;
-+
-+/** Type for a mutex */
-+typedef struct dwc_mutex dwc_mutex_t;
-+
-+/* For Linux Mutex Debugging make it inline because the debugging routines use
-+ * the symbol to determine recursive locking. This makes it falsely think
-+ * recursive locking occurs. */
-+#if defined(DWC_LINUX) && defined(CONFIG_DEBUG_MUTEXES)
-+#define DWC_MUTEX_ALLOC_LINUX_DEBUG(__mutexp) ({ \
-+ __mutexp = (dwc_mutex_t *)DWC_ALLOC(sizeof(struct mutex)); \
-+ mutex_init((struct mutex *)__mutexp); \
-+})
-+#endif
-+
-+/** Allocate a mutex */
-+extern dwc_mutex_t *DWC_MUTEX_ALLOC(void);
-+#define dwc_mutex_alloc(_ctx_) DWC_MUTEX_ALLOC()
-+
-+/* For memory leak debugging when using Linux Mutex Debugging */
-+#if defined(DWC_LINUX) && defined(CONFIG_DEBUG_MUTEXES)
-+#define DWC_MUTEX_FREE(__mutexp) do { \
-+ mutex_destroy((struct mutex *)__mutexp); \
-+ DWC_FREE(__mutexp); \
-+} while(0)
-+#else
-+/** Free a mutex */
-+extern void DWC_MUTEX_FREE(dwc_mutex_t *mutex);
-+#define dwc_mutex_free(_ctx_,_mutex_) DWC_MUTEX_FREE(_mutex_)
-+#endif
-+
-+/** Lock a mutex */
-+extern void DWC_MUTEX_LOCK(dwc_mutex_t *mutex);
-+#define dwc_mutex_lock DWC_MUTEX_LOCK
-+
-+/** Non-blocking lock returns 1 on successful lock. */
-+extern int DWC_MUTEX_TRYLOCK(dwc_mutex_t *mutex);
-+#define dwc_mutex_trylock DWC_MUTEX_TRYLOCK
-+
-+/** Unlock a mutex */
-+extern void DWC_MUTEX_UNLOCK(dwc_mutex_t *mutex);
-+#define dwc_mutex_unlock DWC_MUTEX_UNLOCK
-+
-+
-+/** @name Time */
-+
-+/** Microsecond delay.
-+ *
-+ * @param usecs Microseconds to delay.
-+ */
-+extern void DWC_UDELAY(uint32_t usecs);
-+#define dwc_udelay DWC_UDELAY
-+
-+/** Millisecond delay.
-+ *
-+ * @param msecs Milliseconds to delay.
-+ */
-+extern void DWC_MDELAY(uint32_t msecs);
-+#define dwc_mdelay DWC_MDELAY
-+
-+/** Non-busy waiting.
-+ * Sleeps for specified number of milliseconds.
-+ *
-+ * @param msecs Milliseconds to sleep.
-+ */
-+extern void DWC_MSLEEP(uint32_t msecs);
-+#define dwc_msleep DWC_MSLEEP
-+
-+/**
-+ * Returns number of milliseconds since boot.
-+ */
-+extern uint32_t DWC_TIME(void);
-+#define dwc_time DWC_TIME
-+
-+
-+
-+
-+/* @mainpage DWC Portability and Common Library
-+ *
-+ * This is the documentation for the DWC Portability and Common Library.
-+ *
-+ * @section intro Introduction
-+ *
-+ * The DWC Portability library consists of wrapper calls and data structures to
-+ * all low-level functions which are typically provided by the OS. The WUDEV
-+ * driver uses only these functions. In order to port the WUDEV driver, only
-+ * the functions in this library need to be re-implemented, with the same
-+ * behavior as documented here.
-+ *
-+ * The Common library consists of higher level functions, which rely only on
-+ * calling the functions from the DWC Portability library. These common
-+ * routines are shared across modules. Some of the common libraries need to be
-+ * used directly by the driver programmer when porting WUDEV. Such as the
-+ * parameter and notification libraries.
-+ *
-+ * @section low Portability Library OS Wrapper Functions
-+ *
-+ * Any function starting with DWC and in all CAPS is a low-level OS-wrapper that
-+ * needs to be implemented when porting, for example DWC_MUTEX_ALLOC(). All of
-+ * these functions are included in the dwc_os.h file.
-+ *
-+ * There are many functions here covering a wide array of OS services. Please
-+ * see dwc_os.h for details, and implementation notes for each function.
-+ *
-+ * @section common Common Library Functions
-+ *
-+ * Any function starting with dwc and in all lowercase is a common library
-+ * routine. These functions have a portable implementation and do not need to
-+ * be reimplemented when porting. The common routines can be used by any
-+ * driver, and some must be used by the end user to control the drivers. For
-+ * example, you must use the Parameter common library in order to set the
-+ * parameters in the WUDEV module.
-+ *
-+ * The common libraries consist of the following:
-+ *
-+ * - Connection Contexts - Used internally and can be used by end-user. See dwc_cc.h
-+ * - Parameters - Used internally and can be used by end-user. See dwc_params.h
-+ * - Notifications - Used internally and can be used by end-user. See dwc_notifier.h
-+ * - Lists - Used internally and can be used by end-user. See dwc_list.h
-+ * - Memory Debugging - Used internally and can be used by end-user. See dwc_os.h
-+ * - Modpow - Used internally only. See dwc_modpow.h
-+ * - DH - Used internally only. See dwc_dh.h
-+ * - Crypto - Used internally only. See dwc_crypto.h
-+ *
-+ *
-+ * @section prereq Prerequistes For dwc_os.h
-+ * @subsection types Data Types
-+ *
-+ * The dwc_os.h file assumes that several low-level data types are pre defined for the
-+ * compilation environment. These data types are:
-+ *
-+ * - uint8_t - unsigned 8-bit data type
-+ * - int8_t - signed 8-bit data type
-+ * - uint16_t - unsigned 16-bit data type
-+ * - int16_t - signed 16-bit data type
-+ * - uint32_t - unsigned 32-bit data type
-+ * - int32_t - signed 32-bit data type
-+ * - uint64_t - unsigned 64-bit data type
-+ * - int64_t - signed 64-bit data type
-+ *
-+ * Ensure that these are defined before using dwc_os.h. The easiest way to do
-+ * that is to modify the top of the file to include the appropriate header.
-+ * This is already done for the Linux environment. If the DWC_LINUX macro is
-+ * defined, the correct header will be added. A standard header <stdint.h> is
-+ * also used for environments where standard C headers are available.
-+ *
-+ * @subsection stdarg Variable Arguments
-+ *
-+ * Variable arguments are provided by a standard C header <stdarg.h>. it is
-+ * available in Both the Linux and ANSI C enviornment. An equivalent must be
-+ * provided in your enviornment in order to use dwc_os.h with the debug and
-+ * tracing message functionality.
-+ *
-+ * @subsection thread Threading
-+ *
-+ * WUDEV Core must be run on an operating system that provides for multiple
-+ * threads/processes. Threading can be implemented in many ways, even in
-+ * embedded systems without an operating system. At the bare minimum, the
-+ * system should be able to start any number of processes at any time to handle
-+ * special work. It need not be a pre-emptive system. Process context can
-+ * change upon a call to a blocking function. The hardware interrupt context
-+ * that calls the module's ISR() function must be differentiable from process
-+ * context, even if your processes are impemented via a hardware interrupt.
-+ * Further locking mechanism between process must exist (or be implemented), and
-+ * process context must have a way to disable interrupts for a period of time to
-+ * lock them out. If all of this exists, the functions in dwc_os.h related to
-+ * threading should be able to be implemented with the defined behavior.
-+ *
-+ */
-+
-+#ifdef __cplusplus
-+}
-+#endif
-+
-+#endif /* _DWC_OS_H_ */
---- /dev/null
-+++ b/drivers/usb/host/dwc_common_port/usb.h
-@@ -0,0 +1,946 @@
-+/*
-+ * Copyright (c) 1998 The NetBSD Foundation, Inc.
-+ * All rights reserved.
-+ *
-+ * This code is derived from software contributed to The NetBSD Foundation
-+ * by Lennart Augustsson (lennart at augustsson.net) at
-+ * Carlstedt Research & Technology.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions and the following disclaimer.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. All advertising materials mentioning features or use of this software
-+ * must display the following acknowledgement:
-+ * This product includes software developed by the NetBSD
-+ * Foundation, Inc. and its contributors.
-+ * 4. Neither the name of The NetBSD Foundation nor the names of its
-+ * contributors may be used to endorse or promote products derived
-+ * from this software without specific prior written permission.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
-+ * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
-+ * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
-+ * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
-+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
-+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
-+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
-+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
-+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
-+ * POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+/* Modified by Synopsys, Inc, 12/12/2007 */
-+
-+
-+#ifndef _USB_H_
-+#define _USB_H_
-+
-+#ifdef __cplusplus
-+extern "C" {
-+#endif
-+
-+/*
-+ * The USB records contain some unaligned little-endian word
-+ * components. The U[SG]ETW macros take care of both the alignment
-+ * and endian problem and should always be used to access non-byte
-+ * values.
-+ */
-+typedef u_int8_t uByte;
-+typedef u_int8_t uWord[2];
-+typedef u_int8_t uDWord[4];
-+
-+#define USETW2(w,h,l) ((w)[0] = (u_int8_t)(l), (w)[1] = (u_int8_t)(h))
-+#define UCONSTW(x) { (x) & 0xff, ((x) >> 8) & 0xff }
-+#define UCONSTDW(x) { (x) & 0xff, ((x) >> 8) & 0xff, \
-+ ((x) >> 16) & 0xff, ((x) >> 24) & 0xff }
-+
-+#if 1
-+#define UGETW(w) ((w)[0] | ((w)[1] << 8))
-+#define USETW(w,v) ((w)[0] = (u_int8_t)(v), (w)[1] = (u_int8_t)((v) >> 8))
-+#define UGETDW(w) ((w)[0] | ((w)[1] << 8) | ((w)[2] << 16) | ((w)[3] << 24))
-+#define USETDW(w,v) ((w)[0] = (u_int8_t)(v), \
-+ (w)[1] = (u_int8_t)((v) >> 8), \
-+ (w)[2] = (u_int8_t)((v) >> 16), \
-+ (w)[3] = (u_int8_t)((v) >> 24))
-+#else
-+/*
-+ * On little-endian machines that can handle unanliged accesses
-+ * (e.g. i386) these macros can be replaced by the following.
-+ */
-+#define UGETW(w) (*(u_int16_t *)(w))
-+#define USETW(w,v) (*(u_int16_t *)(w) = (v))
-+#define UGETDW(w) (*(u_int32_t *)(w))
-+#define USETDW(w,v) (*(u_int32_t *)(w) = (v))
-+#endif
-+
-+/*
-+ * Macros for accessing UAS IU fields, which are big-endian
-+ */
-+#define IUSETW2(w,h,l) ((w)[0] = (u_int8_t)(h), (w)[1] = (u_int8_t)(l))
-+#define IUCONSTW(x) { ((x) >> 8) & 0xff, (x) & 0xff }
-+#define IUCONSTDW(x) { ((x) >> 24) & 0xff, ((x) >> 16) & 0xff, \
-+ ((x) >> 8) & 0xff, (x) & 0xff }
-+#define IUGETW(w) (((w)[0] << 8) | (w)[1])
-+#define IUSETW(w,v) ((w)[0] = (u_int8_t)((v) >> 8), (w)[1] = (u_int8_t)(v))
-+#define IUGETDW(w) (((w)[0] << 24) | ((w)[1] << 16) | ((w)[2] << 8) | (w)[3])
-+#define IUSETDW(w,v) ((w)[0] = (u_int8_t)((v) >> 24), \
-+ (w)[1] = (u_int8_t)((v) >> 16), \
-+ (w)[2] = (u_int8_t)((v) >> 8), \
-+ (w)[3] = (u_int8_t)(v))
-+
-+#define UPACKED __attribute__((__packed__))
-+
-+typedef struct {
-+ uByte bmRequestType;
-+ uByte bRequest;
-+ uWord wValue;
-+ uWord wIndex;
-+ uWord wLength;
-+} UPACKED usb_device_request_t;
-+
-+#define UT_GET_DIR(a) ((a) & 0x80)
-+#define UT_WRITE 0x00
-+#define UT_READ 0x80
-+
-+#define UT_GET_TYPE(a) ((a) & 0x60)
-+#define UT_STANDARD 0x00
-+#define UT_CLASS 0x20
-+#define UT_VENDOR 0x40
-+
-+#define UT_GET_RECIPIENT(a) ((a) & 0x1f)
-+#define UT_DEVICE 0x00
-+#define UT_INTERFACE 0x01
-+#define UT_ENDPOINT 0x02
-+#define UT_OTHER 0x03
-+
-+#define UT_READ_DEVICE (UT_READ | UT_STANDARD | UT_DEVICE)
-+#define UT_READ_INTERFACE (UT_READ | UT_STANDARD | UT_INTERFACE)
-+#define UT_READ_ENDPOINT (UT_READ | UT_STANDARD | UT_ENDPOINT)
-+#define UT_WRITE_DEVICE (UT_WRITE | UT_STANDARD | UT_DEVICE)
-+#define UT_WRITE_INTERFACE (UT_WRITE | UT_STANDARD | UT_INTERFACE)
-+#define UT_WRITE_ENDPOINT (UT_WRITE | UT_STANDARD | UT_ENDPOINT)
-+#define UT_READ_CLASS_DEVICE (UT_READ | UT_CLASS | UT_DEVICE)
-+#define UT_READ_CLASS_INTERFACE (UT_READ | UT_CLASS | UT_INTERFACE)
-+#define UT_READ_CLASS_OTHER (UT_READ | UT_CLASS | UT_OTHER)
-+#define UT_READ_CLASS_ENDPOINT (UT_READ | UT_CLASS | UT_ENDPOINT)
-+#define UT_WRITE_CLASS_DEVICE (UT_WRITE | UT_CLASS | UT_DEVICE)
-+#define UT_WRITE_CLASS_INTERFACE (UT_WRITE | UT_CLASS | UT_INTERFACE)
-+#define UT_WRITE_CLASS_OTHER (UT_WRITE | UT_CLASS | UT_OTHER)
-+#define UT_WRITE_CLASS_ENDPOINT (UT_WRITE | UT_CLASS | UT_ENDPOINT)
-+#define UT_READ_VENDOR_DEVICE (UT_READ | UT_VENDOR | UT_DEVICE)
-+#define UT_READ_VENDOR_INTERFACE (UT_READ | UT_VENDOR | UT_INTERFACE)
-+#define UT_READ_VENDOR_OTHER (UT_READ | UT_VENDOR | UT_OTHER)
-+#define UT_READ_VENDOR_ENDPOINT (UT_READ | UT_VENDOR | UT_ENDPOINT)
-+#define UT_WRITE_VENDOR_DEVICE (UT_WRITE | UT_VENDOR | UT_DEVICE)
-+#define UT_WRITE_VENDOR_INTERFACE (UT_WRITE | UT_VENDOR | UT_INTERFACE)
-+#define UT_WRITE_VENDOR_OTHER (UT_WRITE | UT_VENDOR | UT_OTHER)
-+#define UT_WRITE_VENDOR_ENDPOINT (UT_WRITE | UT_VENDOR | UT_ENDPOINT)
-+
-+/* Requests */
-+#define UR_GET_STATUS 0x00
-+#define USTAT_STANDARD_STATUS 0x00
-+#define WUSTAT_WUSB_FEATURE 0x01
-+#define WUSTAT_CHANNEL_INFO 0x02
-+#define WUSTAT_RECEIVED_DATA 0x03
-+#define WUSTAT_MAS_AVAILABILITY 0x04
-+#define WUSTAT_CURRENT_TRANSMIT_POWER 0x05
-+#define UR_CLEAR_FEATURE 0x01
-+#define UR_SET_FEATURE 0x03
-+#define UR_SET_AND_TEST_FEATURE 0x0c
-+#define UR_SET_ADDRESS 0x05
-+#define UR_GET_DESCRIPTOR 0x06
-+#define UDESC_DEVICE 0x01
-+#define UDESC_CONFIG 0x02
-+#define UDESC_STRING 0x03
-+#define UDESC_INTERFACE 0x04
-+#define UDESC_ENDPOINT 0x05
-+#define UDESC_SS_USB_COMPANION 0x30
-+#define UDESC_DEVICE_QUALIFIER 0x06
-+#define UDESC_OTHER_SPEED_CONFIGURATION 0x07
-+#define UDESC_INTERFACE_POWER 0x08
-+#define UDESC_OTG 0x09
-+#define WUDESC_SECURITY 0x0c
-+#define WUDESC_KEY 0x0d
-+#define WUD_GET_KEY_INDEX(_wValue_) ((_wValue_) & 0xf)
-+#define WUD_GET_KEY_TYPE(_wValue_) (((_wValue_) & 0x30) >> 4)
-+#define WUD_KEY_TYPE_ASSOC 0x01
-+#define WUD_KEY_TYPE_GTK 0x02
-+#define WUD_GET_KEY_ORIGIN(_wValue_) (((_wValue_) & 0x40) >> 6)
-+#define WUD_KEY_ORIGIN_HOST 0x00
-+#define WUD_KEY_ORIGIN_DEVICE 0x01
-+#define WUDESC_ENCRYPTION_TYPE 0x0e
-+#define WUDESC_BOS 0x0f
-+#define WUDESC_DEVICE_CAPABILITY 0x10
-+#define WUDESC_WIRELESS_ENDPOINT_COMPANION 0x11
-+#define UDESC_BOS 0x0f
-+#define UDESC_DEVICE_CAPABILITY 0x10
-+#define UDESC_CS_DEVICE 0x21 /* class specific */
-+#define UDESC_CS_CONFIG 0x22
-+#define UDESC_CS_STRING 0x23
-+#define UDESC_CS_INTERFACE 0x24
-+#define UDESC_CS_ENDPOINT 0x25
-+#define UDESC_HUB 0x29
-+#define UR_SET_DESCRIPTOR 0x07
-+#define UR_GET_CONFIG 0x08
-+#define UR_SET_CONFIG 0x09
-+#define UR_GET_INTERFACE 0x0a
-+#define UR_SET_INTERFACE 0x0b
-+#define UR_SYNCH_FRAME 0x0c
-+#define WUR_SET_ENCRYPTION 0x0d
-+#define WUR_GET_ENCRYPTION 0x0e
-+#define WUR_SET_HANDSHAKE 0x0f
-+#define WUR_GET_HANDSHAKE 0x10
-+#define WUR_SET_CONNECTION 0x11
-+#define WUR_SET_SECURITY_DATA 0x12
-+#define WUR_GET_SECURITY_DATA 0x13
-+#define WUR_SET_WUSB_DATA 0x14
-+#define WUDATA_DRPIE_INFO 0x01
-+#define WUDATA_TRANSMIT_DATA 0x02
-+#define WUDATA_TRANSMIT_PARAMS 0x03
-+#define WUDATA_RECEIVE_PARAMS 0x04
-+#define WUDATA_TRANSMIT_POWER 0x05
-+#define WUR_LOOPBACK_DATA_WRITE 0x15
-+#define WUR_LOOPBACK_DATA_READ 0x16
-+#define WUR_SET_INTERFACE_DS 0x17
-+
-+/* Feature numbers */
-+#define UF_ENDPOINT_HALT 0
-+#define UF_DEVICE_REMOTE_WAKEUP 1
-+#define UF_TEST_MODE 2
-+#define UF_DEVICE_B_HNP_ENABLE 3
-+#define UF_DEVICE_A_HNP_SUPPORT 4
-+#define UF_DEVICE_A_ALT_HNP_SUPPORT 5
-+#define WUF_WUSB 3
-+#define WUF_TX_DRPIE 0x0
-+#define WUF_DEV_XMIT_PACKET 0x1
-+#define WUF_COUNT_PACKETS 0x2
-+#define WUF_CAPTURE_PACKETS 0x3
-+#define UF_FUNCTION_SUSPEND 0
-+#define UF_U1_ENABLE 48
-+#define UF_U2_ENABLE 49
-+#define UF_LTM_ENABLE 50
-+
-+/* Class requests from the USB 2.0 hub spec, table 11-15 */
-+#define UCR_CLEAR_HUB_FEATURE (0x2000 | UR_CLEAR_FEATURE)
-+#define UCR_CLEAR_PORT_FEATURE (0x2300 | UR_CLEAR_FEATURE)
-+#define UCR_GET_HUB_DESCRIPTOR (0xa000 | UR_GET_DESCRIPTOR)
-+#define UCR_GET_HUB_STATUS (0xa000 | UR_GET_STATUS)
-+#define UCR_GET_PORT_STATUS (0xa300 | UR_GET_STATUS)
-+#define UCR_SET_HUB_FEATURE (0x2000 | UR_SET_FEATURE)
-+#define UCR_SET_PORT_FEATURE (0x2300 | UR_SET_FEATURE)
-+#define UCR_SET_AND_TEST_PORT_FEATURE (0xa300 | UR_SET_AND_TEST_FEATURE)
-+
-+#ifdef _MSC_VER
-+#include <pshpack1.h>
-+#endif
-+
-+typedef struct {
-+ uByte bLength;
-+ uByte bDescriptorType;
-+ uByte bDescriptorSubtype;
-+} UPACKED usb_descriptor_t;
-+
-+typedef struct {
-+ uByte bLength;
-+ uByte bDescriptorType;
-+} UPACKED usb_descriptor_header_t;
-+
-+typedef struct {
-+ uByte bLength;
-+ uByte bDescriptorType;
-+ uWord bcdUSB;
-+#define UD_USB_2_0 0x0200
-+#define UD_IS_USB2(d) (UGETW((d)->bcdUSB) >= UD_USB_2_0)
-+ uByte bDeviceClass;
-+ uByte bDeviceSubClass;
-+ uByte bDeviceProtocol;
-+ uByte bMaxPacketSize;
-+ /* The fields below are not part of the initial descriptor. */
-+ uWord idVendor;
-+ uWord idProduct;
-+ uWord bcdDevice;
-+ uByte iManufacturer;
-+ uByte iProduct;
-+ uByte iSerialNumber;
-+ uByte bNumConfigurations;
-+} UPACKED usb_device_descriptor_t;
-+#define USB_DEVICE_DESCRIPTOR_SIZE 18
-+
-+typedef struct {
-+ uByte bLength;
-+ uByte bDescriptorType;
-+ uWord wTotalLength;
-+ uByte bNumInterface;
-+ uByte bConfigurationValue;
-+ uByte iConfiguration;
-+#define UC_ATT_ONE (1 << 7) /* must be set */
-+#define UC_ATT_SELFPOWER (1 << 6) /* self powered */
-+#define UC_ATT_WAKEUP (1 << 5) /* can wakeup */
-+#define UC_ATT_BATTERY (1 << 4) /* battery powered */
-+ uByte bmAttributes;
-+#define UC_BUS_POWERED 0x80
-+#define UC_SELF_POWERED 0x40
-+#define UC_REMOTE_WAKEUP 0x20
-+ uByte bMaxPower; /* max current in 2 mA units */
-+#define UC_POWER_FACTOR 2
-+} UPACKED usb_config_descriptor_t;
-+#define USB_CONFIG_DESCRIPTOR_SIZE 9
-+
-+typedef struct {
-+ uByte bLength;
-+ uByte bDescriptorType;
-+ uByte bInterfaceNumber;
-+ uByte bAlternateSetting;
-+ uByte bNumEndpoints;
-+ uByte bInterfaceClass;
-+ uByte bInterfaceSubClass;
-+ uByte bInterfaceProtocol;
-+ uByte iInterface;
-+} UPACKED usb_interface_descriptor_t;
-+#define USB_INTERFACE_DESCRIPTOR_SIZE 9
-+
-+typedef struct {
-+ uByte bLength;
-+ uByte bDescriptorType;
-+ uByte bEndpointAddress;
-+#define UE_GET_DIR(a) ((a) & 0x80)
-+#define UE_SET_DIR(a,d) ((a) | (((d)&1) << 7))
-+#define UE_DIR_IN 0x80
-+#define UE_DIR_OUT 0x00
-+#define UE_ADDR 0x0f
-+#define UE_GET_ADDR(a) ((a) & UE_ADDR)
-+ uByte bmAttributes;
-+#define UE_XFERTYPE 0x03
-+#define UE_CONTROL 0x00
-+#define UE_ISOCHRONOUS 0x01
-+#define UE_BULK 0x02
-+#define UE_INTERRUPT 0x03
-+#define UE_GET_XFERTYPE(a) ((a) & UE_XFERTYPE)
-+#define UE_ISO_TYPE 0x0c
-+#define UE_ISO_ASYNC 0x04
-+#define UE_ISO_ADAPT 0x08
-+#define UE_ISO_SYNC 0x0c
-+#define UE_GET_ISO_TYPE(a) ((a) & UE_ISO_TYPE)
-+ uWord wMaxPacketSize;
-+ uByte bInterval;
-+} UPACKED usb_endpoint_descriptor_t;
-+#define USB_ENDPOINT_DESCRIPTOR_SIZE 7
-+
-+typedef struct ss_endpoint_companion_descriptor {
-+ uByte bLength;
-+ uByte bDescriptorType;
-+ uByte bMaxBurst;
-+#define USSE_GET_MAX_STREAMS(a) ((a) & 0x1f)
-+#define USSE_SET_MAX_STREAMS(a, b) ((a) | ((b) & 0x1f))
-+#define USSE_GET_MAX_PACKET_NUM(a) ((a) & 0x03)
-+#define USSE_SET_MAX_PACKET_NUM(a, b) ((a) | ((b) & 0x03))
-+ uByte bmAttributes;
-+ uWord wBytesPerInterval;
-+} UPACKED ss_endpoint_companion_descriptor_t;
-+#define USB_SS_ENDPOINT_COMPANION_DESCRIPTOR_SIZE 6
-+
-+typedef struct {
-+ uByte bLength;
-+ uByte bDescriptorType;
-+ uWord bString[127];
-+} UPACKED usb_string_descriptor_t;
-+#define USB_MAX_STRING_LEN 128
-+#define USB_LANGUAGE_TABLE 0 /* # of the string language id table */
-+
-+/* Hub specific request */
-+#define UR_GET_BUS_STATE 0x02
-+#define UR_CLEAR_TT_BUFFER 0x08
-+#define UR_RESET_TT 0x09
-+#define UR_GET_TT_STATE 0x0a
-+#define UR_STOP_TT 0x0b
-+
-+/* Hub features */
-+#define UHF_C_HUB_LOCAL_POWER 0
-+#define UHF_C_HUB_OVER_CURRENT 1
-+#define UHF_PORT_CONNECTION 0
-+#define UHF_PORT_ENABLE 1
-+#define UHF_PORT_SUSPEND 2
-+#define UHF_PORT_OVER_CURRENT 3
-+#define UHF_PORT_RESET 4
-+#define UHF_PORT_L1 5
-+#define UHF_PORT_POWER 8
-+#define UHF_PORT_LOW_SPEED 9
-+#define UHF_PORT_HIGH_SPEED 10
-+#define UHF_C_PORT_CONNECTION 16
-+#define UHF_C_PORT_ENABLE 17
-+#define UHF_C_PORT_SUSPEND 18
-+#define UHF_C_PORT_OVER_CURRENT 19
-+#define UHF_C_PORT_RESET 20
-+#define UHF_C_PORT_L1 23
-+#define UHF_PORT_TEST 21
-+#define UHF_PORT_INDICATOR 22
-+
-+typedef struct {
-+ uByte bDescLength;
-+ uByte bDescriptorType;
-+ uByte bNbrPorts;
-+ uWord wHubCharacteristics;
-+#define UHD_PWR 0x0003
-+#define UHD_PWR_GANGED 0x0000
-+#define UHD_PWR_INDIVIDUAL 0x0001
-+#define UHD_PWR_NO_SWITCH 0x0002
-+#define UHD_COMPOUND 0x0004
-+#define UHD_OC 0x0018
-+#define UHD_OC_GLOBAL 0x0000
-+#define UHD_OC_INDIVIDUAL 0x0008
-+#define UHD_OC_NONE 0x0010
-+#define UHD_TT_THINK 0x0060
-+#define UHD_TT_THINK_8 0x0000
-+#define UHD_TT_THINK_16 0x0020
-+#define UHD_TT_THINK_24 0x0040
-+#define UHD_TT_THINK_32 0x0060
-+#define UHD_PORT_IND 0x0080
-+ uByte bPwrOn2PwrGood; /* delay in 2 ms units */
-+#define UHD_PWRON_FACTOR 2
-+ uByte bHubContrCurrent;
-+ uByte DeviceRemovable[32]; /* max 255 ports */
-+#define UHD_NOT_REMOV(desc, i) \
-+ (((desc)->DeviceRemovable[(i)/8] >> ((i) % 8)) & 1)
-+ /* deprecated */ uByte PortPowerCtrlMask[1];
-+} UPACKED usb_hub_descriptor_t;
-+#define USB_HUB_DESCRIPTOR_SIZE 9 /* includes deprecated PortPowerCtrlMask */
-+
-+typedef struct {
-+ uByte bLength;
-+ uByte bDescriptorType;
-+ uWord bcdUSB;
-+ uByte bDeviceClass;
-+ uByte bDeviceSubClass;
-+ uByte bDeviceProtocol;
-+ uByte bMaxPacketSize0;
-+ uByte bNumConfigurations;
-+ uByte bReserved;
-+} UPACKED usb_device_qualifier_t;
-+#define USB_DEVICE_QUALIFIER_SIZE 10
-+
-+typedef struct {
-+ uByte bLength;
-+ uByte bDescriptorType;
-+ uByte bmAttributes;
-+#define UOTG_SRP 0x01
-+#define UOTG_HNP 0x02
-+} UPACKED usb_otg_descriptor_t;
-+
-+/* OTG feature selectors */
-+#define UOTG_B_HNP_ENABLE 3
-+#define UOTG_A_HNP_SUPPORT 4
-+#define UOTG_A_ALT_HNP_SUPPORT 5
-+
-+typedef struct {
-+ uWord wStatus;
-+/* Device status flags */
-+#define UDS_SELF_POWERED 0x0001
-+#define UDS_REMOTE_WAKEUP 0x0002
-+/* Endpoint status flags */
-+#define UES_HALT 0x0001
-+} UPACKED usb_status_t;
-+
-+typedef struct {
-+ uWord wHubStatus;
-+#define UHS_LOCAL_POWER 0x0001
-+#define UHS_OVER_CURRENT 0x0002
-+ uWord wHubChange;
-+} UPACKED usb_hub_status_t;
-+
-+typedef struct {
-+ uWord wPortStatus;
-+#define UPS_CURRENT_CONNECT_STATUS 0x0001
-+#define UPS_PORT_ENABLED 0x0002
-+#define UPS_SUSPEND 0x0004
-+#define UPS_OVERCURRENT_INDICATOR 0x0008
-+#define UPS_RESET 0x0010
-+#define UPS_PORT_POWER 0x0100
-+#define UPS_LOW_SPEED 0x0200
-+#define UPS_HIGH_SPEED 0x0400
-+#define UPS_PORT_TEST 0x0800
-+#define UPS_PORT_INDICATOR 0x1000
-+ uWord wPortChange;
-+#define UPS_C_CONNECT_STATUS 0x0001
-+#define UPS_C_PORT_ENABLED 0x0002
-+#define UPS_C_SUSPEND 0x0004
-+#define UPS_C_OVERCURRENT_INDICATOR 0x0008
-+#define UPS_C_PORT_RESET 0x0010
-+} UPACKED usb_port_status_t;
-+
-+#ifdef _MSC_VER
-+#include <poppack.h>
-+#endif
-+
-+/* Device class codes */
-+#define UDCLASS_IN_INTERFACE 0x00
-+#define UDCLASS_COMM 0x02
-+#define UDCLASS_HUB 0x09
-+#define UDSUBCLASS_HUB 0x00
-+#define UDPROTO_FSHUB 0x00
-+#define UDPROTO_HSHUBSTT 0x01
-+#define UDPROTO_HSHUBMTT 0x02
-+#define UDCLASS_DIAGNOSTIC 0xdc
-+#define UDCLASS_WIRELESS 0xe0
-+#define UDSUBCLASS_RF 0x01
-+#define UDPROTO_BLUETOOTH 0x01
-+#define UDCLASS_VENDOR 0xff
-+
-+/* Interface class codes */
-+#define UICLASS_UNSPEC 0x00
-+
-+#define UICLASS_AUDIO 0x01
-+#define UISUBCLASS_AUDIOCONTROL 1
-+#define UISUBCLASS_AUDIOSTREAM 2
-+#define UISUBCLASS_MIDISTREAM 3
-+
-+#define UICLASS_CDC 0x02 /* communication */
-+#define UISUBCLASS_DIRECT_LINE_CONTROL_MODEL 1
-+#define UISUBCLASS_ABSTRACT_CONTROL_MODEL 2
-+#define UISUBCLASS_TELEPHONE_CONTROL_MODEL 3
-+#define UISUBCLASS_MULTICHANNEL_CONTROL_MODEL 4
-+#define UISUBCLASS_CAPI_CONTROLMODEL 5
-+#define UISUBCLASS_ETHERNET_NETWORKING_CONTROL_MODEL 6
-+#define UISUBCLASS_ATM_NETWORKING_CONTROL_MODEL 7
-+#define UIPROTO_CDC_AT 1
-+
-+#define UICLASS_HID 0x03
-+#define UISUBCLASS_BOOT 1
-+#define UIPROTO_BOOT_KEYBOARD 1
-+
-+#define UICLASS_PHYSICAL 0x05
-+
-+#define UICLASS_IMAGE 0x06
-+
-+#define UICLASS_PRINTER 0x07
-+#define UISUBCLASS_PRINTER 1
-+#define UIPROTO_PRINTER_UNI 1
-+#define UIPROTO_PRINTER_BI 2
-+#define UIPROTO_PRINTER_1284 3
-+
-+#define UICLASS_MASS 0x08
-+#define UISUBCLASS_RBC 1
-+#define UISUBCLASS_SFF8020I 2
-+#define UISUBCLASS_QIC157 3
-+#define UISUBCLASS_UFI 4
-+#define UISUBCLASS_SFF8070I 5
-+#define UISUBCLASS_SCSI 6
-+#define UIPROTO_MASS_CBI_I 0
-+#define UIPROTO_MASS_CBI 1
-+#define UIPROTO_MASS_BBB_OLD 2 /* Not in the spec anymore */
-+#define UIPROTO_MASS_BBB 80 /* 'P' for the Iomega Zip drive */
-+
-+#define UICLASS_HUB 0x09
-+#define UISUBCLASS_HUB 0
-+#define UIPROTO_FSHUB 0
-+#define UIPROTO_HSHUBSTT 0 /* Yes, same as previous */
-+#define UIPROTO_HSHUBMTT 1
-+
-+#define UICLASS_CDC_DATA 0x0a
-+#define UISUBCLASS_DATA 0
-+#define UIPROTO_DATA_ISDNBRI 0x30 /* Physical iface */
-+#define UIPROTO_DATA_HDLC 0x31 /* HDLC */
-+#define UIPROTO_DATA_TRANSPARENT 0x32 /* Transparent */
-+#define UIPROTO_DATA_Q921M 0x50 /* Management for Q921 */
-+#define UIPROTO_DATA_Q921 0x51 /* Data for Q921 */
-+#define UIPROTO_DATA_Q921TM 0x52 /* TEI multiplexer for Q921 */
-+#define UIPROTO_DATA_V42BIS 0x90 /* Data compression */
-+#define UIPROTO_DATA_Q931 0x91 /* Euro-ISDN */
-+#define UIPROTO_DATA_V120 0x92 /* V.24 rate adaption */
-+#define UIPROTO_DATA_CAPI 0x93 /* CAPI 2.0 commands */
-+#define UIPROTO_DATA_HOST_BASED 0xfd /* Host based driver */
-+#define UIPROTO_DATA_PUF 0xfe /* see Prot. Unit Func. Desc.*/
-+#define UIPROTO_DATA_VENDOR 0xff /* Vendor specific */
-+
-+#define UICLASS_SMARTCARD 0x0b
-+
-+/*#define UICLASS_FIRM_UPD 0x0c*/
-+
-+#define UICLASS_SECURITY 0x0d
-+
-+#define UICLASS_DIAGNOSTIC 0xdc
-+
-+#define UICLASS_WIRELESS 0xe0
-+#define UISUBCLASS_RF 0x01
-+#define UIPROTO_BLUETOOTH 0x01
-+
-+#define UICLASS_APPL_SPEC 0xfe
-+#define UISUBCLASS_FIRMWARE_DOWNLOAD 1
-+#define UISUBCLASS_IRDA 2
-+#define UIPROTO_IRDA 0
-+
-+#define UICLASS_VENDOR 0xff
-+
-+#define USB_HUB_MAX_DEPTH 5
-+
-+/*
-+ * Minimum time a device needs to be powered down to go through
-+ * a power cycle. XXX Are these time in the spec?
-+ */
-+#define USB_POWER_DOWN_TIME 200 /* ms */
-+#define USB_PORT_POWER_DOWN_TIME 100 /* ms */
-+
-+#if 0
-+/* These are the values from the spec. */
-+#define USB_PORT_RESET_DELAY 10 /* ms */
-+#define USB_PORT_ROOT_RESET_DELAY 50 /* ms */
-+#define USB_PORT_RESET_RECOVERY 10 /* ms */
-+#define USB_PORT_POWERUP_DELAY 100 /* ms */
-+#define USB_SET_ADDRESS_SETTLE 2 /* ms */
-+#define USB_RESUME_DELAY (20*5) /* ms */
-+#define USB_RESUME_WAIT 10 /* ms */
-+#define USB_RESUME_RECOVERY 10 /* ms */
-+#define USB_EXTRA_POWER_UP_TIME 0 /* ms */
-+#else
-+/* Allow for marginal (i.e. non-conforming) devices. */
-+#define USB_PORT_RESET_DELAY 50 /* ms */
-+#define USB_PORT_ROOT_RESET_DELAY 250 /* ms */
-+#define USB_PORT_RESET_RECOVERY 250 /* ms */
-+#define USB_PORT_POWERUP_DELAY 300 /* ms */
-+#define USB_SET_ADDRESS_SETTLE 10 /* ms */
-+#define USB_RESUME_DELAY (50*5) /* ms */
-+#define USB_RESUME_WAIT 50 /* ms */
-+#define USB_RESUME_RECOVERY 50 /* ms */
-+#define USB_EXTRA_POWER_UP_TIME 20 /* ms */
-+#endif
-+
-+#define USB_MIN_POWER 100 /* mA */
-+#define USB_MAX_POWER 500 /* mA */
-+
-+#define USB_BUS_RESET_DELAY 100 /* ms XXX?*/
-+
-+#define USB_UNCONFIG_NO 0
-+#define USB_UNCONFIG_INDEX (-1)
-+
-+/*** ioctl() related stuff ***/
-+
-+struct usb_ctl_request {
-+ int ucr_addr;
-+ usb_device_request_t ucr_request;
-+ void *ucr_data;
-+ int ucr_flags;
-+#define USBD_SHORT_XFER_OK 0x04 /* allow short reads */
-+ int ucr_actlen; /* actual length transferred */
-+};
-+
-+struct usb_alt_interface {
-+ int uai_config_index;
-+ int uai_interface_index;
-+ int uai_alt_no;
-+};
-+
-+#define USB_CURRENT_CONFIG_INDEX (-1)
-+#define USB_CURRENT_ALT_INDEX (-1)
-+
-+struct usb_config_desc {
-+ int ucd_config_index;
-+ usb_config_descriptor_t ucd_desc;
-+};
-+
-+struct usb_interface_desc {
-+ int uid_config_index;
-+ int uid_interface_index;
-+ int uid_alt_index;
-+ usb_interface_descriptor_t uid_desc;
-+};
-+
-+struct usb_endpoint_desc {
-+ int ued_config_index;
-+ int ued_interface_index;
-+ int ued_alt_index;
-+ int ued_endpoint_index;
-+ usb_endpoint_descriptor_t ued_desc;
-+};
-+
-+struct usb_full_desc {
-+ int ufd_config_index;
-+ u_int ufd_size;
-+ u_char *ufd_data;
-+};
-+
-+struct usb_string_desc {
-+ int usd_string_index;
-+ int usd_language_id;
-+ usb_string_descriptor_t usd_desc;
-+};
-+
-+struct usb_ctl_report_desc {
-+ int ucrd_size;
-+ u_char ucrd_data[1024]; /* filled data size will vary */
-+};
-+
-+typedef struct { u_int32_t cookie; } usb_event_cookie_t;
-+
-+#define USB_MAX_DEVNAMES 4
-+#define USB_MAX_DEVNAMELEN 16
-+struct usb_device_info {
-+ u_int8_t udi_bus;
-+ u_int8_t udi_addr; /* device address */
-+ usb_event_cookie_t udi_cookie;
-+ char udi_product[USB_MAX_STRING_LEN];
-+ char udi_vendor[USB_MAX_STRING_LEN];
-+ char udi_release[8];
-+ u_int16_t udi_productNo;
-+ u_int16_t udi_vendorNo;
-+ u_int16_t udi_releaseNo;
-+ u_int8_t udi_class;
-+ u_int8_t udi_subclass;
-+ u_int8_t udi_protocol;
-+ u_int8_t udi_config;
-+ u_int8_t udi_speed;
-+#define USB_SPEED_UNKNOWN 0
-+#define USB_SPEED_LOW 1
-+#define USB_SPEED_FULL 2
-+#define USB_SPEED_HIGH 3
-+#define USB_SPEED_VARIABLE 4
-+#define USB_SPEED_SUPER 5
-+ int udi_power; /* power consumption in mA, 0 if selfpowered */
-+ int udi_nports;
-+ char udi_devnames[USB_MAX_DEVNAMES][USB_MAX_DEVNAMELEN];
-+ u_int8_t udi_ports[16];/* hub only: addresses of devices on ports */
-+#define USB_PORT_ENABLED 0xff
-+#define USB_PORT_SUSPENDED 0xfe
-+#define USB_PORT_POWERED 0xfd
-+#define USB_PORT_DISABLED 0xfc
-+};
-+
-+struct usb_ctl_report {
-+ int ucr_report;
-+ u_char ucr_data[1024]; /* filled data size will vary */
-+};
-+
-+struct usb_device_stats {
-+ u_long uds_requests[4]; /* indexed by transfer type UE_* */
-+};
-+
-+#define WUSB_MIN_IE 0x80
-+#define WUSB_WCTA_IE 0x80
-+#define WUSB_WCONNECTACK_IE 0x81
-+#define WUSB_WHOSTINFO_IE 0x82
-+#define WUHI_GET_CA(_bmAttributes_) ((_bmAttributes_) & 0x3)
-+#define WUHI_CA_RECONN 0x00
-+#define WUHI_CA_LIMITED 0x01
-+#define WUHI_CA_ALL 0x03
-+#define WUHI_GET_MLSI(_bmAttributes_) (((_bmAttributes_) & 0x38) >> 3)
-+#define WUSB_WCHCHANGEANNOUNCE_IE 0x83
-+#define WUSB_WDEV_DISCONNECT_IE 0x84
-+#define WUSB_WHOST_DISCONNECT_IE 0x85
-+#define WUSB_WRELEASE_CHANNEL_IE 0x86
-+#define WUSB_WWORK_IE 0x87
-+#define WUSB_WCHANNEL_STOP_IE 0x88
-+#define WUSB_WDEV_KEEPALIVE_IE 0x89
-+#define WUSB_WISOCH_DISCARD_IE 0x8A
-+#define WUSB_WRESETDEVICE_IE 0x8B
-+#define WUSB_WXMIT_PACKET_ADJUST_IE 0x8C
-+#define WUSB_MAX_IE 0x8C
-+
-+/* Device Notification Types */
-+
-+#define WUSB_DN_MIN 0x01
-+#define WUSB_DN_CONNECT 0x01
-+# define WUSB_DA_OLDCONN 0x00
-+# define WUSB_DA_NEWCONN 0x01
-+# define WUSB_DA_SELF_BEACON 0x02
-+# define WUSB_DA_DIR_BEACON 0x04
-+# define WUSB_DA_NO_BEACON 0x06
-+#define WUSB_DN_DISCONNECT 0x02
-+#define WUSB_DN_EPRDY 0x03
-+#define WUSB_DN_MASAVAILCHANGED 0x04
-+#define WUSB_DN_REMOTEWAKEUP 0x05
-+#define WUSB_DN_SLEEP 0x06
-+#define WUSB_DN_ALIVE 0x07
-+#define WUSB_DN_MAX 0x07
-+
-+#ifdef _MSC_VER
-+#include <pshpack1.h>
-+#endif
-+
-+/* WUSB Handshake Data. Used during the SET/GET HANDSHAKE requests */
-+typedef struct wusb_hndshk_data {
-+ uByte bMessageNumber;
-+ uByte bStatus;
-+ uByte tTKID[3];
-+ uByte bReserved;
-+ uByte CDID[16];
-+ uByte Nonce[16];
-+ uByte MIC[8];
-+} UPACKED wusb_hndshk_data_t;
-+#define WUSB_HANDSHAKE_LEN_FOR_MIC 38
-+
-+/* WUSB Connection Context */
-+typedef struct wusb_conn_context {
-+ uByte CHID [16];
-+ uByte CDID [16];
-+ uByte CK [16];
-+} UPACKED wusb_conn_context_t;
-+
-+/* WUSB Security Descriptor */
-+typedef struct wusb_security_desc {
-+ uByte bLength;
-+ uByte bDescriptorType;
-+ uWord wTotalLength;
-+ uByte bNumEncryptionTypes;
-+} UPACKED wusb_security_desc_t;
-+
-+/* WUSB Encryption Type Descriptor */
-+typedef struct wusb_encrypt_type_desc {
-+ uByte bLength;
-+ uByte bDescriptorType;
-+
-+ uByte bEncryptionType;
-+#define WUETD_UNSECURE 0
-+#define WUETD_WIRED 1
-+#define WUETD_CCM_1 2
-+#define WUETD_RSA_1 3
-+
-+ uByte bEncryptionValue;
-+ uByte bAuthKeyIndex;
-+} UPACKED wusb_encrypt_type_desc_t;
-+
-+/* WUSB Key Descriptor */
-+typedef struct wusb_key_desc {
-+ uByte bLength;
-+ uByte bDescriptorType;
-+ uByte tTKID[3];
-+ uByte bReserved;
-+ uByte KeyData[1]; /* variable length */
-+} UPACKED wusb_key_desc_t;
-+
-+/* WUSB BOS Descriptor (Binary device Object Store) */
-+typedef struct wusb_bos_desc {
-+ uByte bLength;
-+ uByte bDescriptorType;
-+ uWord wTotalLength;
-+ uByte bNumDeviceCaps;
-+} UPACKED wusb_bos_desc_t;
-+
-+#define USB_DEVICE_CAPABILITY_20_EXTENSION 0x02
-+typedef struct usb_dev_cap_20_ext_desc {
-+ uByte bLength;
-+ uByte bDescriptorType;
-+ uByte bDevCapabilityType;
-+#define USB_20_EXT_LPM 0x02
-+ uDWord bmAttributes;
-+} UPACKED usb_dev_cap_20_ext_desc_t;
-+
-+#define USB_DEVICE_CAPABILITY_SS_USB 0x03
-+typedef struct usb_dev_cap_ss_usb {
-+ uByte bLength;
-+ uByte bDescriptorType;
-+ uByte bDevCapabilityType;
-+#define USB_DC_SS_USB_LTM_CAPABLE 0x02
-+ uByte bmAttributes;
-+#define USB_DC_SS_USB_SPEED_SUPPORT_LOW 0x01
-+#define USB_DC_SS_USB_SPEED_SUPPORT_FULL 0x02
-+#define USB_DC_SS_USB_SPEED_SUPPORT_HIGH 0x04
-+#define USB_DC_SS_USB_SPEED_SUPPORT_SS 0x08
-+ uWord wSpeedsSupported;
-+ uByte bFunctionalitySupport;
-+ uByte bU1DevExitLat;
-+ uWord wU2DevExitLat;
-+} UPACKED usb_dev_cap_ss_usb_t;
-+
-+#define USB_DEVICE_CAPABILITY_CONTAINER_ID 0x04
-+typedef struct usb_dev_cap_container_id {
-+ uByte bLength;
-+ uByte bDescriptorType;
-+ uByte bDevCapabilityType;
-+ uByte bReserved;
-+ uByte containerID[16];
-+} UPACKED usb_dev_cap_container_id_t;
-+
-+/* Device Capability Type Codes */
-+#define WUSB_DEVICE_CAPABILITY_WIRELESS_USB 0x01
-+
-+/* Device Capability Descriptor */
-+typedef struct wusb_dev_cap_desc {
-+ uByte bLength;
-+ uByte bDescriptorType;
-+ uByte bDevCapabilityType;
-+ uByte caps[1]; /* Variable length */
-+} UPACKED wusb_dev_cap_desc_t;
-+
-+/* Device Capability Descriptor */
-+typedef struct wusb_dev_cap_uwb_desc {
-+ uByte bLength;
-+ uByte bDescriptorType;
-+ uByte bDevCapabilityType;
-+ uByte bmAttributes;
-+ uWord wPHYRates; /* Bitmap */
-+ uByte bmTFITXPowerInfo;
-+ uByte bmFFITXPowerInfo;
-+ uWord bmBandGroup;
-+ uByte bReserved;
-+} UPACKED wusb_dev_cap_uwb_desc_t;
-+
-+/* Wireless USB Endpoint Companion Descriptor */
-+typedef struct wusb_endpoint_companion_desc {
-+ uByte bLength;
-+ uByte bDescriptorType;
-+ uByte bMaxBurst;
-+ uByte bMaxSequence;
-+ uWord wMaxStreamDelay;
-+ uWord wOverTheAirPacketSize;
-+ uByte bOverTheAirInterval;
-+ uByte bmCompAttributes;
-+} UPACKED wusb_endpoint_companion_desc_t;
-+
-+/* Wireless USB Numeric Association M1 Data Structure */
-+typedef struct wusb_m1_data {
-+ uByte version;
-+ uWord langId;
-+ uByte deviceFriendlyNameLength;
-+ uByte sha_256_m3[32];
-+ uByte deviceFriendlyName[256];
-+} UPACKED wusb_m1_data_t;
-+
-+typedef struct wusb_m2_data {
-+ uByte version;
-+ uWord langId;
-+ uByte hostFriendlyNameLength;
-+ uByte pkh[384];
-+ uByte hostFriendlyName[256];
-+} UPACKED wusb_m2_data_t;
-+
-+typedef struct wusb_m3_data {
-+ uByte pkd[384];
-+ uByte nd;
-+} UPACKED wusb_m3_data_t;
-+
-+typedef struct wusb_m4_data {
-+ uDWord _attributeTypeIdAndLength_1;
-+ uWord associationTypeId;
-+
-+ uDWord _attributeTypeIdAndLength_2;
-+ uWord associationSubTypeId;
-+
-+ uDWord _attributeTypeIdAndLength_3;
-+ uDWord length;
-+
-+ uDWord _attributeTypeIdAndLength_4;
-+ uDWord associationStatus;
-+
-+ uDWord _attributeTypeIdAndLength_5;
-+ uByte chid[16];
-+
-+ uDWord _attributeTypeIdAndLength_6;
-+ uByte cdid[16];
-+
-+ uDWord _attributeTypeIdAndLength_7;
-+ uByte bandGroups[2];
-+} UPACKED wusb_m4_data_t;
-+
-+#ifdef _MSC_VER
-+#include <poppack.h>
-+#endif
-+
-+#ifdef __cplusplus
-+}
-+#endif
-+
-+#endif /* _USB_H_ */
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/Makefile
-@@ -0,0 +1,82 @@
-+#
-+# Makefile for DWC_otg Highspeed USB controller driver
-+#
-+
-+ifneq ($(KERNELRELEASE),)
-+
-+# Use the BUS_INTERFACE variable to compile the software for either
-+# PCI(PCI_INTERFACE) or LM(LM_INTERFACE) bus.
-+ifeq ($(BUS_INTERFACE),)
-+# BUS_INTERFACE = -DPCI_INTERFACE
-+# BUS_INTERFACE = -DLM_INTERFACE
-+ BUS_INTERFACE = -DPLATFORM_INTERFACE
-+endif
-+
-+#ccflags-y += -DDEBUG
-+#ccflags-y += -DDWC_OTG_DEBUGLEV=1 # reduce common debug msgs
-+
-+# Use one of the following flags to compile the software in host-only or
-+# device-only mode.
-+#ccflags-y += -DDWC_HOST_ONLY
-+#ccflags-y += -DDWC_DEVICE_ONLY
-+
-+ccflags-y += -Dlinux -DDWC_HS_ELECT_TST
-+#ccflags-y += -DDWC_EN_ISOC
-+ccflags-y += -I$(obj)/../dwc_common_port
-+#ccflags-y += -I$(PORTLIB)
-+ccflags-y += -DDWC_LINUX
-+ccflags-y += $(CFI)
-+ccflags-y += $(BUS_INTERFACE)
-+#ccflags-y += -DDWC_DEV_SRPCAP
-+
-+obj-$(CONFIG_USB_DWCOTG) += dwc_otg.o
-+
-+dwc_otg-objs := dwc_otg_driver.o dwc_otg_attr.o
-+dwc_otg-objs += dwc_otg_cil.o dwc_otg_cil_intr.o
-+dwc_otg-objs += dwc_otg_pcd_linux.o dwc_otg_pcd.o dwc_otg_pcd_intr.o
-+dwc_otg-objs += dwc_otg_hcd.o dwc_otg_hcd_linux.o dwc_otg_hcd_intr.o dwc_otg_hcd_queue.o dwc_otg_hcd_ddma.o
-+dwc_otg-objs += dwc_otg_adp.o
-+dwc_otg-objs += dwc_otg_fiq_fsm.o
-+dwc_otg-objs += dwc_otg_fiq_stub.o
-+ifneq ($(CFI),)
-+dwc_otg-objs += dwc_otg_cfi.o
-+endif
-+
-+kernrelwd := $(subst ., ,$(KERNELRELEASE))
-+kernrel3 := $(word 1,$(kernrelwd)).$(word 2,$(kernrelwd)).$(word 3,$(kernrelwd))
-+
-+ifneq ($(kernrel3),2.6.20)
-+ccflags-y += $(CPPFLAGS)
-+endif
-+
-+else
-+
-+PWD := $(shell pwd)
-+PORTLIB := $(PWD)/../dwc_common_port
-+
-+# Command paths
-+CTAGS := $(CTAGS)
-+DOXYGEN := $(DOXYGEN)
-+
-+default: portlib
-+ $(MAKE) -C$(KDIR) M=$(PWD) ARCH=$(ARCH) CROSS_COMPILE=$(CROSS_COMPILE) modules
-+
-+install: default
-+ $(MAKE) -C$(KDIR) M=$(PORTLIB) modules_install
-+ $(MAKE) -C$(KDIR) M=$(PWD) modules_install
-+
-+portlib:
-+ $(MAKE) -C$(KDIR) M=$(PORTLIB) ARCH=$(ARCH) CROSS_COMPILE=$(CROSS_COMPILE) modules
-+ cp $(PORTLIB)/Module.symvers $(PWD)/
-+
-+docs: $(wildcard *.[hc]) doc/doxygen.cfg
-+ $(DOXYGEN) doc/doxygen.cfg
-+
-+tags: $(wildcard *.[hc])
-+ $(CTAGS) -e $(wildcard *.[hc]) $(wildcard linux/*.[hc]) $(wildcard $(KDIR)/include/linux/usb*.h)
-+
-+
-+clean:
-+ rm -rf *.o *.ko .*cmd *.mod.c .tmp_versions Module.symvers
-+
-+endif
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/doc/doxygen.cfg
-@@ -0,0 +1,224 @@
-+# Doxyfile 1.3.9.1
-+
-+#---------------------------------------------------------------------------
-+# Project related configuration options
-+#---------------------------------------------------------------------------
-+PROJECT_NAME = "DesignWare USB 2.0 OTG Controller (DWC_otg) Device Driver"
-+PROJECT_NUMBER = v3.00a
-+OUTPUT_DIRECTORY = ./doc/
-+CREATE_SUBDIRS = NO
-+OUTPUT_LANGUAGE = English
-+BRIEF_MEMBER_DESC = YES
-+REPEAT_BRIEF = YES
-+ABBREVIATE_BRIEF = "The $name class" \
-+ "The $name widget" \
-+ "The $name file" \
-+ is \
-+ provides \
-+ specifies \
-+ contains \
-+ represents \
-+ a \
-+ an \
-+ the
-+ALWAYS_DETAILED_SEC = NO
-+INLINE_INHERITED_MEMB = NO
-+FULL_PATH_NAMES = NO
-+STRIP_FROM_PATH =
-+STRIP_FROM_INC_PATH =
-+SHORT_NAMES = NO
-+JAVADOC_AUTOBRIEF = YES
-+MULTILINE_CPP_IS_BRIEF = NO
-+INHERIT_DOCS = YES
-+DISTRIBUTE_GROUP_DOC = NO
-+TAB_SIZE = 8
-+ALIASES =
-+OPTIMIZE_OUTPUT_FOR_C = YES
-+OPTIMIZE_OUTPUT_JAVA = NO
-+SUBGROUPING = YES
-+#---------------------------------------------------------------------------
-+# Build related configuration options
-+#---------------------------------------------------------------------------
-+EXTRACT_ALL = NO
-+EXTRACT_PRIVATE = YES
-+EXTRACT_STATIC = YES
-+EXTRACT_LOCAL_CLASSES = YES
-+EXTRACT_LOCAL_METHODS = NO
-+HIDE_UNDOC_MEMBERS = NO
-+HIDE_UNDOC_CLASSES = NO
-+HIDE_FRIEND_COMPOUNDS = NO
-+HIDE_IN_BODY_DOCS = NO
-+INTERNAL_DOCS = NO
-+CASE_SENSE_NAMES = NO
-+HIDE_SCOPE_NAMES = NO
-+SHOW_INCLUDE_FILES = YES
-+INLINE_INFO = YES
-+SORT_MEMBER_DOCS = NO
-+SORT_BRIEF_DOCS = NO
-+SORT_BY_SCOPE_NAME = NO
-+GENERATE_TODOLIST = YES
-+GENERATE_TESTLIST = YES
-+GENERATE_BUGLIST = YES
-+GENERATE_DEPRECATEDLIST= YES
-+ENABLED_SECTIONS =
-+MAX_INITIALIZER_LINES = 30
-+SHOW_USED_FILES = YES
-+SHOW_DIRECTORIES = YES
-+#---------------------------------------------------------------------------
-+# configuration options related to warning and progress messages
-+#---------------------------------------------------------------------------
-+QUIET = YES
-+WARNINGS = YES
-+WARN_IF_UNDOCUMENTED = NO
-+WARN_IF_DOC_ERROR = YES
-+WARN_FORMAT = "$file:$line: $text"
-+WARN_LOGFILE =
-+#---------------------------------------------------------------------------
-+# configuration options related to the input files
-+#---------------------------------------------------------------------------
-+INPUT = .
-+FILE_PATTERNS = *.c \
-+ *.h \
-+ ./linux/*.c \
-+ ./linux/*.h
-+RECURSIVE = NO
-+EXCLUDE = ./test/ \
-+ ./dwc_otg/.AppleDouble/
-+EXCLUDE_SYMLINKS = YES
-+EXCLUDE_PATTERNS = *.mod.*
-+EXAMPLE_PATH =
-+EXAMPLE_PATTERNS = *
-+EXAMPLE_RECURSIVE = NO
-+IMAGE_PATH =
-+INPUT_FILTER =
-+FILTER_PATTERNS =
-+FILTER_SOURCE_FILES = NO
-+#---------------------------------------------------------------------------
-+# configuration options related to source browsing
-+#---------------------------------------------------------------------------
-+SOURCE_BROWSER = YES
-+INLINE_SOURCES = NO
-+STRIP_CODE_COMMENTS = YES
-+REFERENCED_BY_RELATION = NO
-+REFERENCES_RELATION = NO
-+VERBATIM_HEADERS = NO
-+#---------------------------------------------------------------------------
-+# configuration options related to the alphabetical class index
-+#---------------------------------------------------------------------------
-+ALPHABETICAL_INDEX = NO
-+COLS_IN_ALPHA_INDEX = 5
-+IGNORE_PREFIX =
-+#---------------------------------------------------------------------------
-+# configuration options related to the HTML output
-+#---------------------------------------------------------------------------
-+GENERATE_HTML = YES
-+HTML_OUTPUT = html
-+HTML_FILE_EXTENSION = .html
-+HTML_HEADER =
-+HTML_FOOTER =
-+HTML_STYLESHEET =
-+HTML_ALIGN_MEMBERS = YES
-+GENERATE_HTMLHELP = NO
-+CHM_FILE =
-+HHC_LOCATION =
-+GENERATE_CHI = NO
-+BINARY_TOC = NO
-+TOC_EXPAND = NO
-+DISABLE_INDEX = NO
-+ENUM_VALUES_PER_LINE = 4
-+GENERATE_TREEVIEW = YES
-+TREEVIEW_WIDTH = 250
-+#---------------------------------------------------------------------------
-+# configuration options related to the LaTeX output
-+#---------------------------------------------------------------------------
-+GENERATE_LATEX = NO
-+LATEX_OUTPUT = latex
-+LATEX_CMD_NAME = latex
-+MAKEINDEX_CMD_NAME = makeindex
-+COMPACT_LATEX = NO
-+PAPER_TYPE = a4wide
-+EXTRA_PACKAGES =
-+LATEX_HEADER =
-+PDF_HYPERLINKS = NO
-+USE_PDFLATEX = NO
-+LATEX_BATCHMODE = NO
-+LATEX_HIDE_INDICES = NO
-+#---------------------------------------------------------------------------
-+# configuration options related to the RTF output
-+#---------------------------------------------------------------------------
-+GENERATE_RTF = NO
-+RTF_OUTPUT = rtf
-+COMPACT_RTF = NO
-+RTF_HYPERLINKS = NO
-+RTF_STYLESHEET_FILE =
-+RTF_EXTENSIONS_FILE =
-+#---------------------------------------------------------------------------
-+# configuration options related to the man page output
-+#---------------------------------------------------------------------------
-+GENERATE_MAN = NO
-+MAN_OUTPUT = man
-+MAN_EXTENSION = .3
-+MAN_LINKS = NO
-+#---------------------------------------------------------------------------
-+# configuration options related to the XML output
-+#---------------------------------------------------------------------------
-+GENERATE_XML = NO
-+XML_OUTPUT = xml
-+XML_SCHEMA =
-+XML_DTD =
-+XML_PROGRAMLISTING = YES
-+#---------------------------------------------------------------------------
-+# configuration options for the AutoGen Definitions output
-+#---------------------------------------------------------------------------
-+GENERATE_AUTOGEN_DEF = NO
-+#---------------------------------------------------------------------------
-+# configuration options related to the Perl module output
-+#---------------------------------------------------------------------------
-+GENERATE_PERLMOD = NO
-+PERLMOD_LATEX = NO
-+PERLMOD_PRETTY = YES
-+PERLMOD_MAKEVAR_PREFIX =
-+#---------------------------------------------------------------------------
-+# Configuration options related to the preprocessor
-+#---------------------------------------------------------------------------
-+ENABLE_PREPROCESSING = YES
-+MACRO_EXPANSION = YES
-+EXPAND_ONLY_PREDEF = YES
-+SEARCH_INCLUDES = YES
-+INCLUDE_PATH =
-+INCLUDE_FILE_PATTERNS =
-+PREDEFINED = DEVICE_ATTR DWC_EN_ISOC
-+EXPAND_AS_DEFINED = DWC_OTG_DEVICE_ATTR_BITFIELD_SHOW DWC_OTG_DEVICE_ATTR_BITFIELD_STORE DWC_OTG_DEVICE_ATTR_BITFIELD_RW DWC_OTG_DEVICE_ATTR_BITFIELD_RO DWC_OTG_DEVICE_ATTR_REG_SHOW DWC_OTG_DEVICE_ATTR_REG_STORE DWC_OTG_DEVICE_ATTR_REG32_RW DWC_OTG_DEVICE_ATTR_REG32_RO DWC_EN_ISOC
-+SKIP_FUNCTION_MACROS = NO
-+#---------------------------------------------------------------------------
-+# Configuration::additions related to external references
-+#---------------------------------------------------------------------------
-+TAGFILES =
-+GENERATE_TAGFILE =
-+ALLEXTERNALS = NO
-+EXTERNAL_GROUPS = YES
-+PERL_PATH = /usr/bin/perl
-+#---------------------------------------------------------------------------
-+# Configuration options related to the dot tool
-+#---------------------------------------------------------------------------
-+CLASS_DIAGRAMS = YES
-+HIDE_UNDOC_RELATIONS = YES
-+HAVE_DOT = NO
-+CLASS_GRAPH = YES
-+COLLABORATION_GRAPH = YES
-+UML_LOOK = NO
-+TEMPLATE_RELATIONS = NO
-+INCLUDE_GRAPH = YES
-+INCLUDED_BY_GRAPH = YES
-+CALL_GRAPH = NO
-+GRAPHICAL_HIERARCHY = YES
-+DOT_IMAGE_FORMAT = png
-+DOT_PATH =
-+DOTFILE_DIRS =
-+MAX_DOT_GRAPH_DEPTH = 1000
-+GENERATE_LEGEND = YES
-+DOT_CLEANUP = YES
-+#---------------------------------------------------------------------------
-+# Configuration::additions related to the search engine
-+#---------------------------------------------------------------------------
-+SEARCHENGINE = NO
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dummy_audio.c
-@@ -0,0 +1,1575 @@
-+/*
-+ * zero.c -- Gadget Zero, for USB development
-+ *
-+ * Copyright (C) 2003-2004 David Brownell
-+ * All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") as published by the Free Software
-+ * Foundation, either version 2 of that License or (at your option) any
-+ * later version.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+
-+/*
-+ * Gadget Zero only needs two bulk endpoints, and is an example of how you
-+ * can write a hardware-agnostic gadget driver running inside a USB device.
-+ *
-+ * Hardware details are visible (see CONFIG_USB_ZERO_* below) but don't
-+ * affect most of the driver.
-+ *
-+ * Use it with the Linux host/master side "usbtest" driver to get a basic
-+ * functional test of your device-side usb stack, or with "usb-skeleton".
-+ *
-+ * It supports two similar configurations. One sinks whatever the usb host
-+ * writes, and in return sources zeroes. The other loops whatever the host
-+ * writes back, so the host can read it. Module options include:
-+ *
-+ * buflen=N default N=4096, buffer size used
-+ * qlen=N default N=32, how many buffers in the loopback queue
-+ * loopdefault default false, list loopback config first
-+ *
-+ * Many drivers will only have one configuration, letting them be much
-+ * simpler if they also don't support high speed operation (like this
-+ * driver does).
-+ */
-+
-+#include <linux/config.h>
-+#include <linux/module.h>
-+#include <linux/kernel.h>
-+#include <linux/delay.h>
-+#include <linux/ioport.h>
-+#include <linux/sched.h>
-+#include <linux/slab.h>
-+#include <linux/smp_lock.h>
-+#include <linux/errno.h>
-+#include <linux/init.h>
-+#include <linux/timer.h>
-+#include <linux/list.h>
-+#include <linux/interrupt.h>
-+#include <linux/uts.h>
-+#include <linux/version.h>
-+#include <linux/device.h>
-+#include <linux/moduleparam.h>
-+#include <linux/proc_fs.h>
-+
-+#include <asm/byteorder.h>
-+#include <asm/io.h>
-+#include <asm/irq.h>
-+#include <asm/system.h>
-+#include <asm/unaligned.h>
-+
-+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,21)
-+# include <linux/usb/ch9.h>
-+#else
-+# include <linux/usb_ch9.h>
-+#endif
-+
-+#include <linux/usb_gadget.h>
-+
-+
-+/*-------------------------------------------------------------------------*/
-+/*-------------------------------------------------------------------------*/
-+
-+
-+static int utf8_to_utf16le(const char *s, u16 *cp, unsigned len)
-+{
-+ int count = 0;
-+ u8 c;
-+ u16 uchar;
-+
-+ /* this insists on correct encodings, though not minimal ones.
-+ * BUT it currently rejects legit 4-byte UTF-8 code points,
-+ * which need surrogate pairs. (Unicode 3.1 can use them.)
-+ */
-+ while (len != 0 && (c = (u8) *s++) != 0) {
-+ if (unlikely(c & 0x80)) {
-+ // 2-byte sequence:
-+ // 00000yyyyyxxxxxx = 110yyyyy 10xxxxxx
-+ if ((c & 0xe0) == 0xc0) {
-+ uchar = (c & 0x1f) << 6;
-+
-+ c = (u8) *s++;
-+ if ((c & 0xc0) != 0xc0)
-+ goto fail;
-+ c &= 0x3f;
-+ uchar |= c;
-+
-+ // 3-byte sequence (most CJKV characters):
-+ // zzzzyyyyyyxxxxxx = 1110zzzz 10yyyyyy 10xxxxxx
-+ } else if ((c & 0xf0) == 0xe0) {
-+ uchar = (c & 0x0f) << 12;
-+
-+ c = (u8) *s++;
-+ if ((c & 0xc0) != 0xc0)
-+ goto fail;
-+ c &= 0x3f;
-+ uchar |= c << 6;
-+
-+ c = (u8) *s++;
-+ if ((c & 0xc0) != 0xc0)
-+ goto fail;
-+ c &= 0x3f;
-+ uchar |= c;
-+
-+ /* no bogus surrogates */
-+ if (0xd800 <= uchar && uchar <= 0xdfff)
-+ goto fail;
-+
-+ // 4-byte sequence (surrogate pairs, currently rare):
-+ // 11101110wwwwzzzzyy + 110111yyyyxxxxxx
-+ // = 11110uuu 10uuzzzz 10yyyyyy 10xxxxxx
-+ // (uuuuu = wwww + 1)
-+ // FIXME accept the surrogate code points (only)
-+
-+ } else
-+ goto fail;
-+ } else
-+ uchar = c;
-+ put_unaligned (cpu_to_le16 (uchar), cp++);
-+ count++;
-+ len--;
-+ }
-+ return count;
-+fail:
-+ return -1;
-+}
-+
-+
-+/**
-+ * usb_gadget_get_string - fill out a string descriptor
-+ * @table: of c strings encoded using UTF-8
-+ * @id: string id, from low byte of wValue in get string descriptor
-+ * @buf: at least 256 bytes
-+ *
-+ * Finds the UTF-8 string matching the ID, and converts it into a
-+ * string descriptor in utf16-le.
-+ * Returns length of descriptor (always even) or negative errno
-+ *
-+ * If your driver needs stings in multiple languages, you'll probably
-+ * "switch (wIndex) { ... }" in your ep0 string descriptor logic,
-+ * using this routine after choosing which set of UTF-8 strings to use.
-+ * Note that US-ASCII is a strict subset of UTF-8; any string bytes with
-+ * the eighth bit set will be multibyte UTF-8 characters, not ISO-8859/1
-+ * characters (which are also widely used in C strings).
-+ */
-+int
-+usb_gadget_get_string (struct usb_gadget_strings *table, int id, u8 *buf)
-+{
-+ struct usb_string *s;
-+ int len;
-+
-+ /* descriptor 0 has the language id */
-+ if (id == 0) {
-+ buf [0] = 4;
-+ buf [1] = USB_DT_STRING;
-+ buf [2] = (u8) table->language;
-+ buf [3] = (u8) (table->language >> 8);
-+ return 4;
-+ }
-+ for (s = table->strings; s && s->s; s++)
-+ if (s->id == id)
-+ break;
-+
-+ /* unrecognized: stall. */
-+ if (!s || !s->s)
-+ return -EINVAL;
-+
-+ /* string descriptors have length, tag, then UTF16-LE text */
-+ len = min ((size_t) 126, strlen (s->s));
-+ memset (buf + 2, 0, 2 * len); /* zero all the bytes */
-+ len = utf8_to_utf16le(s->s, (u16 *)&buf[2], len);
-+ if (len < 0)
-+ return -EINVAL;
-+ buf [0] = (len + 1) * 2;
-+ buf [1] = USB_DT_STRING;
-+ return buf [0];
-+}
-+
-+
-+/*-------------------------------------------------------------------------*/
-+/*-------------------------------------------------------------------------*/
-+
-+
-+/**
-+ * usb_descriptor_fillbuf - fill buffer with descriptors
-+ * @buf: Buffer to be filled
-+ * @buflen: Size of buf
-+ * @src: Array of descriptor pointers, terminated by null pointer.
-+ *
-+ * Copies descriptors into the buffer, returning the length or a
-+ * negative error code if they can't all be copied. Useful when
-+ * assembling descriptors for an associated set of interfaces used
-+ * as part of configuring a composite device; or in other cases where
-+ * sets of descriptors need to be marshaled.
-+ */
-+int
-+usb_descriptor_fillbuf(void *buf, unsigned buflen,
-+ const struct usb_descriptor_header **src)
-+{
-+ u8 *dest = buf;
-+
-+ if (!src)
-+ return -EINVAL;
-+
-+ /* fill buffer from src[] until null descriptor ptr */
-+ for (; 0 != *src; src++) {
-+ unsigned len = (*src)->bLength;
-+
-+ if (len > buflen)
-+ return -EINVAL;
-+ memcpy(dest, *src, len);
-+ buflen -= len;
-+ dest += len;
-+ }
-+ return dest - (u8 *)buf;
-+}
-+
-+
-+/**
-+ * usb_gadget_config_buf - builts a complete configuration descriptor
-+ * @config: Header for the descriptor, including characteristics such
-+ * as power requirements and number of interfaces.
-+ * @desc: Null-terminated vector of pointers to the descriptors (interface,
-+ * endpoint, etc) defining all functions in this device configuration.
-+ * @buf: Buffer for the resulting configuration descriptor.
-+ * @length: Length of buffer. If this is not big enough to hold the
-+ * entire configuration descriptor, an error code will be returned.
-+ *
-+ * This copies descriptors into the response buffer, building a descriptor
-+ * for that configuration. It returns the buffer length or a negative
-+ * status code. The config.wTotalLength field is set to match the length
-+ * of the result, but other descriptor fields (including power usage and
-+ * interface count) must be set by the caller.
-+ *
-+ * Gadget drivers could use this when constructing a config descriptor
-+ * in response to USB_REQ_GET_DESCRIPTOR. They will need to patch the
-+ * resulting bDescriptorType value if USB_DT_OTHER_SPEED_CONFIG is needed.
-+ */
-+int usb_gadget_config_buf(
-+ const struct usb_config_descriptor *config,
-+ void *buf,
-+ unsigned length,
-+ const struct usb_descriptor_header **desc
-+)
-+{
-+ struct usb_config_descriptor *cp = buf;
-+ int len;
-+
-+ /* config descriptor first */
-+ if (length < USB_DT_CONFIG_SIZE || !desc)
-+ return -EINVAL;
-+ *cp = *config;
-+
-+ /* then interface/endpoint/class/vendor/... */
-+ len = usb_descriptor_fillbuf(USB_DT_CONFIG_SIZE + (u8*)buf,
-+ length - USB_DT_CONFIG_SIZE, desc);
-+ if (len < 0)
-+ return len;
-+ len += USB_DT_CONFIG_SIZE;
-+ if (len > 0xffff)
-+ return -EINVAL;
-+
-+ /* patch up the config descriptor */
-+ cp->bLength = USB_DT_CONFIG_SIZE;
-+ cp->bDescriptorType = USB_DT_CONFIG;
-+ cp->wTotalLength = cpu_to_le16(len);
-+ cp->bmAttributes |= USB_CONFIG_ATT_ONE;
-+ return len;
-+}
-+
-+/*-------------------------------------------------------------------------*/
-+/*-------------------------------------------------------------------------*/
-+
-+
-+#define RBUF_LEN (1024*1024)
-+static int rbuf_start;
-+static int rbuf_len;
-+static __u8 rbuf[RBUF_LEN];
-+
-+/*-------------------------------------------------------------------------*/
-+
-+#define DRIVER_VERSION "St Patrick's Day 2004"
-+
-+static const char shortname [] = "zero";
-+static const char longname [] = "YAMAHA YST-MS35D USB Speaker ";
-+
-+static const char source_sink [] = "source and sink data";
-+static const char loopback [] = "loop input to output";
-+
-+/*-------------------------------------------------------------------------*/
-+
-+/*
-+ * driver assumes self-powered hardware, and
-+ * has no way for users to trigger remote wakeup.
-+ *
-+ * this version autoconfigures as much as possible,
-+ * which is reasonable for most "bulk-only" drivers.
-+ */
-+static const char *EP_IN_NAME; /* source */
-+static const char *EP_OUT_NAME; /* sink */
-+
-+/*-------------------------------------------------------------------------*/
-+
-+/* big enough to hold our biggest descriptor */
-+#define USB_BUFSIZ 512
-+
-+struct zero_dev {
-+ spinlock_t lock;
-+ struct usb_gadget *gadget;
-+ struct usb_request *req; /* for control responses */
-+
-+ /* when configured, we have one of two configs:
-+ * - source data (in to host) and sink it (out from host)
-+ * - or loop it back (out from host back in to host)
-+ */
-+ u8 config;
-+ struct usb_ep *in_ep, *out_ep;
-+
-+ /* autoresume timer */
-+ struct timer_list resume;
-+};
-+
-+#define xprintk(d,level,fmt,args...) \
-+ dev_printk(level , &(d)->gadget->dev , fmt , ## args)
-+
-+#ifdef DEBUG
-+#define DBG(dev,fmt,args...) \
-+ xprintk(dev , KERN_DEBUG , fmt , ## args)
-+#else
-+#define DBG(dev,fmt,args...) \
-+ do { } while (0)
-+#endif /* DEBUG */
-+
-+#ifdef VERBOSE
-+#define VDBG DBG
-+#else
-+#define VDBG(dev,fmt,args...) \
-+ do { } while (0)
-+#endif /* VERBOSE */
-+
-+#define ERROR(dev,fmt,args...) \
-+ xprintk(dev , KERN_ERR , fmt , ## args)
-+#define WARN(dev,fmt,args...) \
-+ xprintk(dev , KERN_WARNING , fmt , ## args)
-+#define INFO(dev,fmt,args...) \
-+ xprintk(dev , KERN_INFO , fmt , ## args)
-+
-+/*-------------------------------------------------------------------------*/
-+
-+static unsigned buflen = 4096;
-+static unsigned qlen = 32;
-+static unsigned pattern = 0;
-+
-+module_param (buflen, uint, S_IRUGO|S_IWUSR);
-+module_param (qlen, uint, S_IRUGO|S_IWUSR);
-+module_param (pattern, uint, S_IRUGO|S_IWUSR);
-+
-+/*
-+ * if it's nonzero, autoresume says how many seconds to wait
-+ * before trying to wake up the host after suspend.
-+ */
-+static unsigned autoresume = 0;
-+module_param (autoresume, uint, 0);
-+
-+/*
-+ * Normally the "loopback" configuration is second (index 1) so
-+ * it's not the default. Here's where to change that order, to
-+ * work better with hosts where config changes are problematic.
-+ * Or controllers (like superh) that only support one config.
-+ */
-+static int loopdefault = 0;
-+
-+module_param (loopdefault, bool, S_IRUGO|S_IWUSR);
-+
-+/*-------------------------------------------------------------------------*/
-+
-+/* Thanks to NetChip Technologies for donating this product ID.
-+ *
-+ * DO NOT REUSE THESE IDs with a protocol-incompatible driver!! Ever!!
-+ * Instead: allocate your own, using normal USB-IF procedures.
-+ */
-+#ifndef CONFIG_USB_ZERO_HNPTEST
-+#define DRIVER_VENDOR_NUM 0x0525 /* NetChip */
-+#define DRIVER_PRODUCT_NUM 0xa4a0 /* Linux-USB "Gadget Zero" */
-+#else
-+#define DRIVER_VENDOR_NUM 0x1a0a /* OTG test device IDs */
-+#define DRIVER_PRODUCT_NUM 0xbadd
-+#endif
-+
-+/*-------------------------------------------------------------------------*/
-+
-+/*
-+ * DESCRIPTORS ... most are static, but strings and (full)
-+ * configuration descriptors are built on demand.
-+ */
-+
-+/*
-+#define STRING_MANUFACTURER 25
-+#define STRING_PRODUCT 42
-+#define STRING_SERIAL 101
-+*/
-+#define STRING_MANUFACTURER 1
-+#define STRING_PRODUCT 2
-+#define STRING_SERIAL 3
-+
-+#define STRING_SOURCE_SINK 250
-+#define STRING_LOOPBACK 251
-+
-+/*
-+ * This device advertises two configurations; these numbers work
-+ * on a pxa250 as well as more flexible hardware.
-+ */
-+#define CONFIG_SOURCE_SINK 3
-+#define CONFIG_LOOPBACK 2
-+
-+/*
-+static struct usb_device_descriptor
-+device_desc = {
-+ .bLength = sizeof device_desc,
-+ .bDescriptorType = USB_DT_DEVICE,
-+
-+ .bcdUSB = __constant_cpu_to_le16 (0x0200),
-+ .bDeviceClass = USB_CLASS_VENDOR_SPEC,
-+
-+ .idVendor = __constant_cpu_to_le16 (DRIVER_VENDOR_NUM),
-+ .idProduct = __constant_cpu_to_le16 (DRIVER_PRODUCT_NUM),
-+ .iManufacturer = STRING_MANUFACTURER,
-+ .iProduct = STRING_PRODUCT,
-+ .iSerialNumber = STRING_SERIAL,
-+ .bNumConfigurations = 2,
-+};
-+*/
-+static struct usb_device_descriptor
-+device_desc = {
-+ .bLength = sizeof device_desc,
-+ .bDescriptorType = USB_DT_DEVICE,
-+ .bcdUSB = __constant_cpu_to_le16 (0x0100),
-+ .bDeviceClass = USB_CLASS_PER_INTERFACE,
-+ .bDeviceSubClass = 0,
-+ .bDeviceProtocol = 0,
-+ .bMaxPacketSize0 = 64,
-+ .bcdDevice = __constant_cpu_to_le16 (0x0100),
-+ .idVendor = __constant_cpu_to_le16 (0x0499),
-+ .idProduct = __constant_cpu_to_le16 (0x3002),
-+ .iManufacturer = STRING_MANUFACTURER,
-+ .iProduct = STRING_PRODUCT,
-+ .iSerialNumber = STRING_SERIAL,
-+ .bNumConfigurations = 1,
-+};
-+
-+static struct usb_config_descriptor
-+z_config = {
-+ .bLength = sizeof z_config,
-+ .bDescriptorType = USB_DT_CONFIG,
-+
-+ /* compute wTotalLength on the fly */
-+ .bNumInterfaces = 2,
-+ .bConfigurationValue = 1,
-+ .iConfiguration = 0,
-+ .bmAttributes = 0x40,
-+ .bMaxPower = 0, /* self-powered */
-+};
-+
-+
-+static struct usb_otg_descriptor
-+otg_descriptor = {
-+ .bLength = sizeof otg_descriptor,
-+ .bDescriptorType = USB_DT_OTG,
-+
-+ .bmAttributes = USB_OTG_SRP,
-+};
-+
-+/* one interface in each configuration */
-+#ifdef CONFIG_USB_GADGET_DUALSPEED
-+
-+/*
-+ * usb 2.0 devices need to expose both high speed and full speed
-+ * descriptors, unless they only run at full speed.
-+ *
-+ * that means alternate endpoint descriptors (bigger packets)
-+ * and a "device qualifier" ... plus more construction options
-+ * for the config descriptor.
-+ */
-+
-+static struct usb_qualifier_descriptor
-+dev_qualifier = {
-+ .bLength = sizeof dev_qualifier,
-+ .bDescriptorType = USB_DT_DEVICE_QUALIFIER,
-+
-+ .bcdUSB = __constant_cpu_to_le16 (0x0200),
-+ .bDeviceClass = USB_CLASS_VENDOR_SPEC,
-+
-+ .bNumConfigurations = 2,
-+};
-+
-+
-+struct usb_cs_as_general_descriptor {
-+ __u8 bLength;
-+ __u8 bDescriptorType;
-+
-+ __u8 bDescriptorSubType;
-+ __u8 bTerminalLink;
-+ __u8 bDelay;
-+ __u16 wFormatTag;
-+} __attribute__ ((packed));
-+
-+struct usb_cs_as_format_descriptor {
-+ __u8 bLength;
-+ __u8 bDescriptorType;
-+
-+ __u8 bDescriptorSubType;
-+ __u8 bFormatType;
-+ __u8 bNrChannels;
-+ __u8 bSubframeSize;
-+ __u8 bBitResolution;
-+ __u8 bSamfreqType;
-+ __u8 tLowerSamFreq[3];
-+ __u8 tUpperSamFreq[3];
-+} __attribute__ ((packed));
-+
-+static const struct usb_interface_descriptor
-+z_audio_control_if_desc = {
-+ .bLength = sizeof z_audio_control_if_desc,
-+ .bDescriptorType = USB_DT_INTERFACE,
-+ .bInterfaceNumber = 0,
-+ .bAlternateSetting = 0,
-+ .bNumEndpoints = 0,
-+ .bInterfaceClass = USB_CLASS_AUDIO,
-+ .bInterfaceSubClass = 0x1,
-+ .bInterfaceProtocol = 0,
-+ .iInterface = 0,
-+};
-+
-+static const struct usb_interface_descriptor
-+z_audio_if_desc = {
-+ .bLength = sizeof z_audio_if_desc,
-+ .bDescriptorType = USB_DT_INTERFACE,
-+ .bInterfaceNumber = 1,
-+ .bAlternateSetting = 0,
-+ .bNumEndpoints = 0,
-+ .bInterfaceClass = USB_CLASS_AUDIO,
-+ .bInterfaceSubClass = 0x2,
-+ .bInterfaceProtocol = 0,
-+ .iInterface = 0,
-+};
-+
-+static const struct usb_interface_descriptor
-+z_audio_if_desc2 = {
-+ .bLength = sizeof z_audio_if_desc,
-+ .bDescriptorType = USB_DT_INTERFACE,
-+ .bInterfaceNumber = 1,
-+ .bAlternateSetting = 1,
-+ .bNumEndpoints = 1,
-+ .bInterfaceClass = USB_CLASS_AUDIO,
-+ .bInterfaceSubClass = 0x2,
-+ .bInterfaceProtocol = 0,
-+ .iInterface = 0,
-+};
-+
-+static const struct usb_cs_as_general_descriptor
-+z_audio_cs_as_if_desc = {
-+ .bLength = 7,
-+ .bDescriptorType = 0x24,
-+
-+ .bDescriptorSubType = 0x01,
-+ .bTerminalLink = 0x01,
-+ .bDelay = 0x0,
-+ .wFormatTag = __constant_cpu_to_le16 (0x0001)
-+};
-+
-+
-+static const struct usb_cs_as_format_descriptor
-+z_audio_cs_as_format_desc = {
-+ .bLength = 0xe,
-+ .bDescriptorType = 0x24,
-+
-+ .bDescriptorSubType = 2,
-+ .bFormatType = 1,
-+ .bNrChannels = 1,
-+ .bSubframeSize = 1,
-+ .bBitResolution = 8,
-+ .bSamfreqType = 0,
-+ .tLowerSamFreq = {0x7e, 0x13, 0x00},
-+ .tUpperSamFreq = {0xe2, 0xd6, 0x00},
-+};
-+
-+static const struct usb_endpoint_descriptor
-+z_iso_ep = {
-+ .bLength = 0x09,
-+ .bDescriptorType = 0x05,
-+ .bEndpointAddress = 0x04,
-+ .bmAttributes = 0x09,
-+ .wMaxPacketSize = 0x0038,
-+ .bInterval = 0x01,
-+ .bRefresh = 0x00,
-+ .bSynchAddress = 0x00,
-+};
-+
-+static char z_iso_ep2[] = {0x07, 0x25, 0x01, 0x00, 0x02, 0x00, 0x02};
-+
-+// 9 bytes
-+static char z_ac_interface_header_desc[] =
-+{ 0x09, 0x24, 0x01, 0x00, 0x01, 0x2b, 0x00, 0x01, 0x01 };
-+
-+// 12 bytes
-+static char z_0[] = {0x0c, 0x24, 0x02, 0x01, 0x01, 0x01, 0x00, 0x02,
-+ 0x03, 0x00, 0x00, 0x00};
-+// 13 bytes
-+static char z_1[] = {0x0d, 0x24, 0x06, 0x02, 0x01, 0x02, 0x15, 0x00,
-+ 0x02, 0x00, 0x02, 0x00, 0x00};
-+// 9 bytes
-+static char z_2[] = {0x09, 0x24, 0x03, 0x03, 0x01, 0x03, 0x00, 0x02,
-+ 0x00};
-+
-+static char za_0[] = {0x09, 0x04, 0x01, 0x02, 0x01, 0x01, 0x02, 0x00,
-+ 0x00};
-+
-+static char za_1[] = {0x07, 0x24, 0x01, 0x01, 0x00, 0x01, 0x00};
-+
-+static char za_2[] = {0x0e, 0x24, 0x02, 0x01, 0x02, 0x01, 0x08, 0x00,
-+ 0x7e, 0x13, 0x00, 0xe2, 0xd6, 0x00};
-+
-+static char za_3[] = {0x09, 0x05, 0x04, 0x09, 0x70, 0x00, 0x01, 0x00,
-+ 0x00};
-+
-+static char za_4[] = {0x07, 0x25, 0x01, 0x00, 0x02, 0x00, 0x02};
-+
-+static char za_5[] = {0x09, 0x04, 0x01, 0x03, 0x01, 0x01, 0x02, 0x00,
-+ 0x00};
-+
-+static char za_6[] = {0x07, 0x24, 0x01, 0x01, 0x00, 0x01, 0x00};
-+
-+static char za_7[] = {0x0e, 0x24, 0x02, 0x01, 0x01, 0x02, 0x10, 0x00,
-+ 0x7e, 0x13, 0x00, 0xe2, 0xd6, 0x00};
-+
-+static char za_8[] = {0x09, 0x05, 0x04, 0x09, 0x70, 0x00, 0x01, 0x00,
-+ 0x00};
-+
-+static char za_9[] = {0x07, 0x25, 0x01, 0x00, 0x02, 0x00, 0x02};
-+
-+static char za_10[] = {0x09, 0x04, 0x01, 0x04, 0x01, 0x01, 0x02, 0x00,
-+ 0x00};
-+
-+static char za_11[] = {0x07, 0x24, 0x01, 0x01, 0x00, 0x01, 0x00};
-+
-+static char za_12[] = {0x0e, 0x24, 0x02, 0x01, 0x02, 0x02, 0x10, 0x00,
-+ 0x73, 0x13, 0x00, 0xe2, 0xd6, 0x00};
-+
-+static char za_13[] = {0x09, 0x05, 0x04, 0x09, 0xe0, 0x00, 0x01, 0x00,
-+ 0x00};
-+
-+static char za_14[] = {0x07, 0x25, 0x01, 0x00, 0x02, 0x00, 0x02};
-+
-+static char za_15[] = {0x09, 0x04, 0x01, 0x05, 0x01, 0x01, 0x02, 0x00,
-+ 0x00};
-+
-+static char za_16[] = {0x07, 0x24, 0x01, 0x01, 0x00, 0x01, 0x00};
-+
-+static char za_17[] = {0x0e, 0x24, 0x02, 0x01, 0x01, 0x03, 0x14, 0x00,
-+ 0x7e, 0x13, 0x00, 0xe2, 0xd6, 0x00};
-+
-+static char za_18[] = {0x09, 0x05, 0x04, 0x09, 0xa8, 0x00, 0x01, 0x00,
-+ 0x00};
-+
-+static char za_19[] = {0x07, 0x25, 0x01, 0x00, 0x02, 0x00, 0x02};
-+
-+static char za_20[] = {0x09, 0x04, 0x01, 0x06, 0x01, 0x01, 0x02, 0x00,
-+ 0x00};
-+
-+static char za_21[] = {0x07, 0x24, 0x01, 0x01, 0x00, 0x01, 0x00};
-+
-+static char za_22[] = {0x0e, 0x24, 0x02, 0x01, 0x02, 0x03, 0x14, 0x00,
-+ 0x7e, 0x13, 0x00, 0xe2, 0xd6, 0x00};
-+
-+static char za_23[] = {0x09, 0x05, 0x04, 0x09, 0x50, 0x01, 0x01, 0x00,
-+ 0x00};
-+
-+static char za_24[] = {0x07, 0x25, 0x01, 0x00, 0x02, 0x00, 0x02};
-+
-+
-+
-+static const struct usb_descriptor_header *z_function [] = {
-+ (struct usb_descriptor_header *) &z_audio_control_if_desc,
-+ (struct usb_descriptor_header *) &z_ac_interface_header_desc,
-+ (struct usb_descriptor_header *) &z_0,
-+ (struct usb_descriptor_header *) &z_1,
-+ (struct usb_descriptor_header *) &z_2,
-+ (struct usb_descriptor_header *) &z_audio_if_desc,
-+ (struct usb_descriptor_header *) &z_audio_if_desc2,
-+ (struct usb_descriptor_header *) &z_audio_cs_as_if_desc,
-+ (struct usb_descriptor_header *) &z_audio_cs_as_format_desc,
-+ (struct usb_descriptor_header *) &z_iso_ep,
-+ (struct usb_descriptor_header *) &z_iso_ep2,
-+ (struct usb_descriptor_header *) &za_0,
-+ (struct usb_descriptor_header *) &za_1,
-+ (struct usb_descriptor_header *) &za_2,
-+ (struct usb_descriptor_header *) &za_3,
-+ (struct usb_descriptor_header *) &za_4,
-+ (struct usb_descriptor_header *) &za_5,
-+ (struct usb_descriptor_header *) &za_6,
-+ (struct usb_descriptor_header *) &za_7,
-+ (struct usb_descriptor_header *) &za_8,
-+ (struct usb_descriptor_header *) &za_9,
-+ (struct usb_descriptor_header *) &za_10,
-+ (struct usb_descriptor_header *) &za_11,
-+ (struct usb_descriptor_header *) &za_12,
-+ (struct usb_descriptor_header *) &za_13,
-+ (struct usb_descriptor_header *) &za_14,
-+ (struct usb_descriptor_header *) &za_15,
-+ (struct usb_descriptor_header *) &za_16,
-+ (struct usb_descriptor_header *) &za_17,
-+ (struct usb_descriptor_header *) &za_18,
-+ (struct usb_descriptor_header *) &za_19,
-+ (struct usb_descriptor_header *) &za_20,
-+ (struct usb_descriptor_header *) &za_21,
-+ (struct usb_descriptor_header *) &za_22,
-+ (struct usb_descriptor_header *) &za_23,
-+ (struct usb_descriptor_header *) &za_24,
-+ NULL,
-+};
-+
-+/* maxpacket and other transfer characteristics vary by speed. */
-+#define ep_desc(g,hs,fs) (((g)->speed==USB_SPEED_HIGH)?(hs):(fs))
-+
-+#else
-+
-+/* if there's no high speed support, maxpacket doesn't change. */
-+#define ep_desc(g,hs,fs) fs
-+
-+#endif /* !CONFIG_USB_GADGET_DUALSPEED */
-+
-+static char manufacturer [40];
-+//static char serial [40];
-+static char serial [] = "Ser 00 em";
-+
-+/* static strings, in UTF-8 */
-+static struct usb_string strings [] = {
-+ { STRING_MANUFACTURER, manufacturer, },
-+ { STRING_PRODUCT, longname, },
-+ { STRING_SERIAL, serial, },
-+ { STRING_LOOPBACK, loopback, },
-+ { STRING_SOURCE_SINK, source_sink, },
-+ { } /* end of list */
-+};
-+
-+static struct usb_gadget_strings stringtab = {
-+ .language = 0x0409, /* en-us */
-+ .strings = strings,
-+};
-+
-+/*
-+ * config descriptors are also handcrafted. these must agree with code
-+ * that sets configurations, and with code managing interfaces and their
-+ * altsettings. other complexity may come from:
-+ *
-+ * - high speed support, including "other speed config" rules
-+ * - multiple configurations
-+ * - interfaces with alternate settings
-+ * - embedded class or vendor-specific descriptors
-+ *
-+ * this handles high speed, and has a second config that could as easily
-+ * have been an alternate interface setting (on most hardware).
-+ *
-+ * NOTE: to demonstrate (and test) more USB capabilities, this driver
-+ * should include an altsetting to test interrupt transfers, including
-+ * high bandwidth modes at high speed. (Maybe work like Intel's test
-+ * device?)
-+ */
-+static int
-+config_buf (struct usb_gadget *gadget, u8 *buf, u8 type, unsigned index)
-+{
-+ int len;
-+ const struct usb_descriptor_header **function;
-+
-+ function = z_function;
-+ len = usb_gadget_config_buf (&z_config, buf, USB_BUFSIZ, function);
-+ if (len < 0)
-+ return len;
-+ ((struct usb_config_descriptor *) buf)->bDescriptorType = type;
-+ return len;
-+}
-+
-+/*-------------------------------------------------------------------------*/
-+
-+static struct usb_request *
-+alloc_ep_req (struct usb_ep *ep, unsigned length)
-+{
-+ struct usb_request *req;
-+
-+ req = usb_ep_alloc_request (ep, GFP_ATOMIC);
-+ if (req) {
-+ req->length = length;
-+ req->buf = usb_ep_alloc_buffer (ep, length,
-+ &req->dma, GFP_ATOMIC);
-+ if (!req->buf) {
-+ usb_ep_free_request (ep, req);
-+ req = NULL;
-+ }
-+ }
-+ return req;
-+}
-+
-+static void free_ep_req (struct usb_ep *ep, struct usb_request *req)
-+{
-+ if (req->buf)
-+ usb_ep_free_buffer (ep, req->buf, req->dma, req->length);
-+ usb_ep_free_request (ep, req);
-+}
-+
-+/*-------------------------------------------------------------------------*/
-+
-+/* optionally require specific source/sink data patterns */
-+
-+static int
-+check_read_data (
-+ struct zero_dev *dev,
-+ struct usb_ep *ep,
-+ struct usb_request *req
-+)
-+{
-+ unsigned i;
-+ u8 *buf = req->buf;
-+
-+ for (i = 0; i < req->actual; i++, buf++) {
-+ switch (pattern) {
-+ /* all-zeroes has no synchronization issues */
-+ case 0:
-+ if (*buf == 0)
-+ continue;
-+ break;
-+ /* mod63 stays in sync with short-terminated transfers,
-+ * or otherwise when host and gadget agree on how large
-+ * each usb transfer request should be. resync is done
-+ * with set_interface or set_config.
-+ */
-+ case 1:
-+ if (*buf == (u8)(i % 63))
-+ continue;
-+ break;
-+ }
-+ ERROR (dev, "bad OUT byte, buf [%d] = %d\n", i, *buf);
-+ usb_ep_set_halt (ep);
-+ return -EINVAL;
-+ }
-+ return 0;
-+}
-+
-+/*-------------------------------------------------------------------------*/
-+
-+static void zero_reset_config (struct zero_dev *dev)
-+{
-+ if (dev->config == 0)
-+ return;
-+
-+ DBG (dev, "reset config\n");
-+
-+ /* just disable endpoints, forcing completion of pending i/o.
-+ * all our completion handlers free their requests in this case.
-+ */
-+ if (dev->in_ep) {
-+ usb_ep_disable (dev->in_ep);
-+ dev->in_ep = NULL;
-+ }
-+ if (dev->out_ep) {
-+ usb_ep_disable (dev->out_ep);
-+ dev->out_ep = NULL;
-+ }
-+ dev->config = 0;
-+ del_timer (&dev->resume);
-+}
-+
-+#define _write(f, buf, sz) (f->f_op->write(f, buf, sz, &f->f_pos))
-+
-+static void
-+zero_isoc_complete (struct usb_ep *ep, struct usb_request *req)
-+{
-+ struct zero_dev *dev = ep->driver_data;
-+ int status = req->status;
-+ int i, j;
-+
-+ switch (status) {
-+
-+ case 0: /* normal completion? */
-+ //printk ("\nzero ---------------> isoc normal completion %d bytes\n", req->actual);
-+ for (i=0, j=rbuf_start; i<req->actual; i++) {
-+ //printk ("%02x ", ((__u8*)req->buf)[i]);
-+ rbuf[j] = ((__u8*)req->buf)[i];
-+ j++;
-+ if (j >= RBUF_LEN) j=0;
-+ }
-+ rbuf_start = j;
-+ //printk ("\n\n");
-+
-+ if (rbuf_len < RBUF_LEN) {
-+ rbuf_len += req->actual;
-+ if (rbuf_len > RBUF_LEN) {
-+ rbuf_len = RBUF_LEN;
-+ }
-+ }
-+
-+ break;
-+
-+ /* this endpoint is normally active while we're configured */
-+ case -ECONNABORTED: /* hardware forced ep reset */
-+ case -ECONNRESET: /* request dequeued */
-+ case -ESHUTDOWN: /* disconnect from host */
-+ VDBG (dev, "%s gone (%d), %d/%d\n", ep->name, status,
-+ req->actual, req->length);
-+ if (ep == dev->out_ep)
-+ check_read_data (dev, ep, req);
-+ free_ep_req (ep, req);
-+ return;
-+
-+ case -EOVERFLOW: /* buffer overrun on read means that
-+ * we didn't provide a big enough
-+ * buffer.
-+ */
-+ default:
-+#if 1
-+ DBG (dev, "%s complete --> %d, %d/%d\n", ep->name,
-+ status, req->actual, req->length);
-+#endif
-+ case -EREMOTEIO: /* short read */
-+ break;
-+ }
-+
-+ status = usb_ep_queue (ep, req, GFP_ATOMIC);
-+ if (status) {
-+ ERROR (dev, "kill %s: resubmit %d bytes --> %d\n",
-+ ep->name, req->length, status);
-+ usb_ep_set_halt (ep);
-+ /* FIXME recover later ... somehow */
-+ }
-+}
-+
-+static struct usb_request *
-+zero_start_isoc_ep (struct usb_ep *ep, int gfp_flags)
-+{
-+ struct usb_request *req;
-+ int status;
-+
-+ req = alloc_ep_req (ep, 512);
-+ if (!req)
-+ return NULL;
-+
-+ req->complete = zero_isoc_complete;
-+
-+ status = usb_ep_queue (ep, req, gfp_flags);
-+ if (status) {
-+ struct zero_dev *dev = ep->driver_data;
-+
-+ ERROR (dev, "start %s --> %d\n", ep->name, status);
-+ free_ep_req (ep, req);
-+ req = NULL;
-+ }
-+
-+ return req;
-+}
-+
-+/* change our operational config. this code must agree with the code
-+ * that returns config descriptors, and altsetting code.
-+ *
-+ * it's also responsible for power management interactions. some
-+ * configurations might not work with our current power sources.
-+ *
-+ * note that some device controller hardware will constrain what this
-+ * code can do, perhaps by disallowing more than one configuration or
-+ * by limiting configuration choices (like the pxa2xx).
-+ */
-+static int
-+zero_set_config (struct zero_dev *dev, unsigned number, int gfp_flags)
-+{
-+ int result = 0;
-+ struct usb_gadget *gadget = dev->gadget;
-+ const struct usb_endpoint_descriptor *d;
-+ struct usb_ep *ep;
-+
-+ if (number == dev->config)
-+ return 0;
-+
-+ zero_reset_config (dev);
-+
-+ gadget_for_each_ep (ep, gadget) {
-+
-+ if (strcmp (ep->name, "ep4") == 0) {
-+
-+ d = (struct usb_endpoint_descripter *)&za_23; // isoc ep desc for audio i/f alt setting 6
-+ result = usb_ep_enable (ep, d);
-+
-+ if (result == 0) {
-+ ep->driver_data = dev;
-+ dev->in_ep = ep;
-+
-+ if (zero_start_isoc_ep (ep, gfp_flags) != 0) {
-+
-+ dev->in_ep = ep;
-+ continue;
-+ }
-+
-+ usb_ep_disable (ep);
-+ result = -EIO;
-+ }
-+ }
-+
-+ }
-+
-+ dev->config = number;
-+ return result;
-+}
-+
-+/*-------------------------------------------------------------------------*/
-+
-+static void zero_setup_complete (struct usb_ep *ep, struct usb_request *req)
-+{
-+ if (req->status || req->actual != req->length)
-+ DBG ((struct zero_dev *) ep->driver_data,
-+ "setup complete --> %d, %d/%d\n",
-+ req->status, req->actual, req->length);
-+}
-+
-+/*
-+ * The setup() callback implements all the ep0 functionality that's
-+ * not handled lower down, in hardware or the hardware driver (like
-+ * device and endpoint feature flags, and their status). It's all
-+ * housekeeping for the gadget function we're implementing. Most of
-+ * the work is in config-specific setup.
-+ */
-+static int
-+zero_setup (struct usb_gadget *gadget, const struct usb_ctrlrequest *ctrl)
-+{
-+ struct zero_dev *dev = get_gadget_data (gadget);
-+ struct usb_request *req = dev->req;
-+ int value = -EOPNOTSUPP;
-+
-+ /* usually this stores reply data in the pre-allocated ep0 buffer,
-+ * but config change events will reconfigure hardware.
-+ */
-+ req->zero = 0;
-+ switch (ctrl->bRequest) {
-+
-+ case USB_REQ_GET_DESCRIPTOR:
-+
-+ switch (ctrl->wValue >> 8) {
-+
-+ case USB_DT_DEVICE:
-+ value = min (ctrl->wLength, (u16) sizeof device_desc);
-+ memcpy (req->buf, &device_desc, value);
-+ break;
-+#ifdef CONFIG_USB_GADGET_DUALSPEED
-+ case USB_DT_DEVICE_QUALIFIER:
-+ if (!gadget->is_dualspeed)
-+ break;
-+ value = min (ctrl->wLength, (u16) sizeof dev_qualifier);
-+ memcpy (req->buf, &dev_qualifier, value);
-+ break;
-+
-+ case USB_DT_OTHER_SPEED_CONFIG:
-+ if (!gadget->is_dualspeed)
-+ break;
-+ // FALLTHROUGH
-+#endif /* CONFIG_USB_GADGET_DUALSPEED */
-+ case USB_DT_CONFIG:
-+ value = config_buf (gadget, req->buf,
-+ ctrl->wValue >> 8,
-+ ctrl->wValue & 0xff);
-+ if (value >= 0)
-+ value = min (ctrl->wLength, (u16) value);
-+ break;
-+
-+ case USB_DT_STRING:
-+ /* wIndex == language code.
-+ * this driver only handles one language, you can
-+ * add string tables for other languages, using
-+ * any UTF-8 characters
-+ */
-+ value = usb_gadget_get_string (&stringtab,
-+ ctrl->wValue & 0xff, req->buf);
-+ if (value >= 0) {
-+ value = min (ctrl->wLength, (u16) value);
-+ }
-+ break;
-+ }
-+ break;
-+
-+ /* currently two configs, two speeds */
-+ case USB_REQ_SET_CONFIGURATION:
-+ if (ctrl->bRequestType != 0)
-+ goto unknown;
-+
-+ spin_lock (&dev->lock);
-+ value = zero_set_config (dev, ctrl->wValue, GFP_ATOMIC);
-+ spin_unlock (&dev->lock);
-+ break;
-+ case USB_REQ_GET_CONFIGURATION:
-+ if (ctrl->bRequestType != USB_DIR_IN)
-+ goto unknown;
-+ *(u8 *)req->buf = dev->config;
-+ value = min (ctrl->wLength, (u16) 1);
-+ break;
-+
-+ /* until we add altsetting support, or other interfaces,
-+ * only 0/0 are possible. pxa2xx only supports 0/0 (poorly)
-+ * and already killed pending endpoint I/O.
-+ */
-+ case USB_REQ_SET_INTERFACE:
-+
-+ if (ctrl->bRequestType != USB_RECIP_INTERFACE)
-+ goto unknown;
-+ spin_lock (&dev->lock);
-+ if (dev->config) {
-+ u8 config = dev->config;
-+
-+ /* resets interface configuration, forgets about
-+ * previous transaction state (queued bufs, etc)
-+ * and re-inits endpoint state (toggle etc)
-+ * no response queued, just zero status == success.
-+ * if we had more than one interface we couldn't
-+ * use this "reset the config" shortcut.
-+ */
-+ zero_reset_config (dev);
-+ zero_set_config (dev, config, GFP_ATOMIC);
-+ value = 0;
-+ }
-+ spin_unlock (&dev->lock);
-+ break;
-+ case USB_REQ_GET_INTERFACE:
-+ if ((ctrl->bRequestType == 0x21) && (ctrl->wIndex == 0x02)) {
-+ value = ctrl->wLength;
-+ break;
-+ }
-+ else {
-+ if (ctrl->bRequestType != (USB_DIR_IN|USB_RECIP_INTERFACE))
-+ goto unknown;
-+ if (!dev->config)
-+ break;
-+ if (ctrl->wIndex != 0) {
-+ value = -EDOM;
-+ break;
-+ }
-+ *(u8 *)req->buf = 0;
-+ value = min (ctrl->wLength, (u16) 1);
-+ }
-+ break;
-+
-+ /*
-+ * These are the same vendor-specific requests supported by
-+ * Intel's USB 2.0 compliance test devices. We exceed that
-+ * device spec by allowing multiple-packet requests.
-+ */
-+ case 0x5b: /* control WRITE test -- fill the buffer */
-+ if (ctrl->bRequestType != (USB_DIR_OUT|USB_TYPE_VENDOR))
-+ goto unknown;
-+ if (ctrl->wValue || ctrl->wIndex)
-+ break;
-+ /* just read that many bytes into the buffer */
-+ if (ctrl->wLength > USB_BUFSIZ)
-+ break;
-+ value = ctrl->wLength;
-+ break;
-+ case 0x5c: /* control READ test -- return the buffer */
-+ if (ctrl->bRequestType != (USB_DIR_IN|USB_TYPE_VENDOR))
-+ goto unknown;
-+ if (ctrl->wValue || ctrl->wIndex)
-+ break;
-+ /* expect those bytes are still in the buffer; send back */
-+ if (ctrl->wLength > USB_BUFSIZ
-+ || ctrl->wLength != req->length)
-+ break;
-+ value = ctrl->wLength;
-+ break;
-+
-+ case 0x01: // SET_CUR
-+ case 0x02:
-+ case 0x03:
-+ case 0x04:
-+ case 0x05:
-+ value = ctrl->wLength;
-+ break;
-+ case 0x81:
-+ switch (ctrl->wValue) {
-+ case 0x0201:
-+ case 0x0202:
-+ ((u8*)req->buf)[0] = 0x00;
-+ ((u8*)req->buf)[1] = 0xe3;
-+ break;
-+ case 0x0300:
-+ case 0x0500:
-+ ((u8*)req->buf)[0] = 0x00;
-+ break;
-+ }
-+ //((u8*)req->buf)[0] = 0x81;
-+ //((u8*)req->buf)[1] = 0x81;
-+ value = ctrl->wLength;
-+ break;
-+ case 0x82:
-+ switch (ctrl->wValue) {
-+ case 0x0201:
-+ case 0x0202:
-+ ((u8*)req->buf)[0] = 0x00;
-+ ((u8*)req->buf)[1] = 0xc3;
-+ break;
-+ case 0x0300:
-+ case 0x0500:
-+ ((u8*)req->buf)[0] = 0x00;
-+ break;
-+ }
-+ //((u8*)req->buf)[0] = 0x82;
-+ //((u8*)req->buf)[1] = 0x82;
-+ value = ctrl->wLength;
-+ break;
-+ case 0x83:
-+ switch (ctrl->wValue) {
-+ case 0x0201:
-+ case 0x0202:
-+ ((u8*)req->buf)[0] = 0x00;
-+ ((u8*)req->buf)[1] = 0x00;
-+ break;
-+ case 0x0300:
-+ ((u8*)req->buf)[0] = 0x60;
-+ break;
-+ case 0x0500:
-+ ((u8*)req->buf)[0] = 0x18;
-+ break;
-+ }
-+ //((u8*)req->buf)[0] = 0x83;
-+ //((u8*)req->buf)[1] = 0x83;
-+ value = ctrl->wLength;
-+ break;
-+ case 0x84:
-+ switch (ctrl->wValue) {
-+ case 0x0201:
-+ case 0x0202:
-+ ((u8*)req->buf)[0] = 0x00;
-+ ((u8*)req->buf)[1] = 0x01;
-+ break;
-+ case 0x0300:
-+ case 0x0500:
-+ ((u8*)req->buf)[0] = 0x08;
-+ break;
-+ }
-+ //((u8*)req->buf)[0] = 0x84;
-+ //((u8*)req->buf)[1] = 0x84;
-+ value = ctrl->wLength;
-+ break;
-+ case 0x85:
-+ ((u8*)req->buf)[0] = 0x85;
-+ ((u8*)req->buf)[1] = 0x85;
-+ value = ctrl->wLength;
-+ break;
-+
-+
-+ default:
-+unknown:
-+ printk("unknown control req%02x.%02x v%04x i%04x l%d\n",
-+ ctrl->bRequestType, ctrl->bRequest,
-+ ctrl->wValue, ctrl->wIndex, ctrl->wLength);
-+ }
-+
-+ /* respond with data transfer before status phase? */
-+ if (value >= 0) {
-+ req->length = value;
-+ req->zero = value < ctrl->wLength
-+ && (value % gadget->ep0->maxpacket) == 0;
-+ value = usb_ep_queue (gadget->ep0, req, GFP_ATOMIC);
-+ if (value < 0) {
-+ DBG (dev, "ep_queue < 0 --> %d\n", value);
-+ req->status = 0;
-+ zero_setup_complete (gadget->ep0, req);
-+ }
-+ }
-+
-+ /* device either stalls (value < 0) or reports success */
-+ return value;
-+}
-+
-+static void
-+zero_disconnect (struct usb_gadget *gadget)
-+{
-+ struct zero_dev *dev = get_gadget_data (gadget);
-+ unsigned long flags;
-+
-+ spin_lock_irqsave (&dev->lock, flags);
-+ zero_reset_config (dev);
-+
-+ /* a more significant application might have some non-usb
-+ * activities to quiesce here, saving resources like power
-+ * or pushing the notification up a network stack.
-+ */
-+ spin_unlock_irqrestore (&dev->lock, flags);
-+
-+ /* next we may get setup() calls to enumerate new connections;
-+ * or an unbind() during shutdown (including removing module).
-+ */
-+}
-+
-+static void
-+zero_autoresume (unsigned long _dev)
-+{
-+ struct zero_dev *dev = (struct zero_dev *) _dev;
-+ int status;
-+
-+ /* normally the host would be woken up for something
-+ * more significant than just a timer firing...
-+ */
-+ if (dev->gadget->speed != USB_SPEED_UNKNOWN) {
-+ status = usb_gadget_wakeup (dev->gadget);
-+ DBG (dev, "wakeup --> %d\n", status);
-+ }
-+}
-+
-+/*-------------------------------------------------------------------------*/
-+
-+static void
-+zero_unbind (struct usb_gadget *gadget)
-+{
-+ struct zero_dev *dev = get_gadget_data (gadget);
-+
-+ DBG (dev, "unbind\n");
-+
-+ /* we've already been disconnected ... no i/o is active */
-+ if (dev->req)
-+ free_ep_req (gadget->ep0, dev->req);
-+ del_timer_sync (&dev->resume);
-+ kfree (dev);
-+ set_gadget_data (gadget, NULL);
-+}
-+
-+static int
-+zero_bind (struct usb_gadget *gadget)
-+{
-+ struct zero_dev *dev;
-+ //struct usb_ep *ep;
-+
-+ printk("binding\n");
-+ /*
-+ * DRIVER POLICY CHOICE: you may want to do this differently.
-+ * One thing to avoid is reusing a bcdDevice revision code
-+ * with different host-visible configurations or behavior
-+ * restrictions -- using ep1in/ep2out vs ep1out/ep3in, etc
-+ */
-+ //device_desc.bcdDevice = __constant_cpu_to_le16 (0x0201);
-+
-+
-+ /* ok, we made sense of the hardware ... */
-+ dev = kmalloc (sizeof *dev, SLAB_KERNEL);
-+ if (!dev)
-+ return -ENOMEM;
-+ memset (dev, 0, sizeof *dev);
-+ spin_lock_init (&dev->lock);
-+ dev->gadget = gadget;
-+ set_gadget_data (gadget, dev);
-+
-+ /* preallocate control response and buffer */
-+ dev->req = usb_ep_alloc_request (gadget->ep0, GFP_KERNEL);
-+ if (!dev->req)
-+ goto enomem;
-+ dev->req->buf = usb_ep_alloc_buffer (gadget->ep0, USB_BUFSIZ,
-+ &dev->req->dma, GFP_KERNEL);
-+ if (!dev->req->buf)
-+ goto enomem;
-+
-+ dev->req->complete = zero_setup_complete;
-+
-+ device_desc.bMaxPacketSize0 = gadget->ep0->maxpacket;
-+
-+#ifdef CONFIG_USB_GADGET_DUALSPEED
-+ /* assume ep0 uses the same value for both speeds ... */
-+ dev_qualifier.bMaxPacketSize0 = device_desc.bMaxPacketSize0;
-+
-+ /* and that all endpoints are dual-speed */
-+ //hs_source_desc.bEndpointAddress = fs_source_desc.bEndpointAddress;
-+ //hs_sink_desc.bEndpointAddress = fs_sink_desc.bEndpointAddress;
-+#endif
-+
-+ usb_gadget_set_selfpowered (gadget);
-+
-+ init_timer (&dev->resume);
-+ dev->resume.function = zero_autoresume;
-+ dev->resume.data = (unsigned long) dev;
-+
-+ gadget->ep0->driver_data = dev;
-+
-+ INFO (dev, "%s, version: " DRIVER_VERSION "\n", longname);
-+ INFO (dev, "using %s, OUT %s IN %s\n", gadget->name,
-+ EP_OUT_NAME, EP_IN_NAME);
-+
-+ snprintf (manufacturer, sizeof manufacturer,
-+ UTS_SYSNAME " " UTS_RELEASE " with %s",
-+ gadget->name);
-+
-+ return 0;
-+
-+enomem:
-+ zero_unbind (gadget);
-+ return -ENOMEM;
-+}
-+
-+/*-------------------------------------------------------------------------*/
-+
-+static void
-+zero_suspend (struct usb_gadget *gadget)
-+{
-+ struct zero_dev *dev = get_gadget_data (gadget);
-+
-+ if (gadget->speed == USB_SPEED_UNKNOWN)
-+ return;
-+
-+ if (autoresume) {
-+ mod_timer (&dev->resume, jiffies + (HZ * autoresume));
-+ DBG (dev, "suspend, wakeup in %d seconds\n", autoresume);
-+ } else
-+ DBG (dev, "suspend\n");
-+}
-+
-+static void
-+zero_resume (struct usb_gadget *gadget)
-+{
-+ struct zero_dev *dev = get_gadget_data (gadget);
-+
-+ DBG (dev, "resume\n");
-+ del_timer (&dev->resume);
-+}
-+
-+
-+/*-------------------------------------------------------------------------*/
-+
-+static struct usb_gadget_driver zero_driver = {
-+#ifdef CONFIG_USB_GADGET_DUALSPEED
-+ .speed = USB_SPEED_HIGH,
-+#else
-+ .speed = USB_SPEED_FULL,
-+#endif
-+ .function = (char *) longname,
-+ .bind = zero_bind,
-+ .unbind = zero_unbind,
-+
-+ .setup = zero_setup,
-+ .disconnect = zero_disconnect,
-+
-+ .suspend = zero_suspend,
-+ .resume = zero_resume,
-+
-+ .driver = {
-+ .name = (char *) shortname,
-+ // .shutdown = ...
-+ // .suspend = ...
-+ // .resume = ...
-+ },
-+};
-+
-+MODULE_AUTHOR ("David Brownell");
-+MODULE_LICENSE ("Dual BSD/GPL");
-+
-+static struct proc_dir_entry *pdir, *pfile;
-+
-+static int isoc_read_data (char *page, char **start,
-+ off_t off, int count,
-+ int *eof, void *data)
-+{
-+ int i;
-+ static int c = 0;
-+ static int done = 0;
-+ static int s = 0;
-+
-+/*
-+ printk ("\ncount: %d\n", count);
-+ printk ("rbuf_start: %d\n", rbuf_start);
-+ printk ("rbuf_len: %d\n", rbuf_len);
-+ printk ("off: %d\n", off);
-+ printk ("start: %p\n\n", *start);
-+*/
-+ if (done) {
-+ c = 0;
-+ done = 0;
-+ *eof = 1;
-+ return 0;
-+ }
-+
-+ if (c == 0) {
-+ if (rbuf_len == RBUF_LEN)
-+ s = rbuf_start;
-+ else s = 0;
-+ }
-+
-+ for (i=0; i<count && c<rbuf_len; i++, c++) {
-+ page[i] = rbuf[(c+s) % RBUF_LEN];
-+ }
-+ *start = page;
-+
-+ if (c >= rbuf_len) {
-+ *eof = 1;
-+ done = 1;
-+ }
-+
-+
-+ return i;
-+}
-+
-+static int __init init (void)
-+{
-+
-+ int retval = 0;
-+
-+ pdir = proc_mkdir("isoc_test", NULL);
-+ if(pdir == NULL) {
-+ retval = -ENOMEM;
-+ printk("Error creating dir\n");
-+ goto done;
-+ }
-+ pdir->owner = THIS_MODULE;
-+
-+ pfile = create_proc_read_entry("isoc_data",
-+ 0444, pdir,
-+ isoc_read_data,
-+ NULL);
-+ if (pfile == NULL) {
-+ retval = -ENOMEM;
-+ printk("Error creating file\n");
-+ goto no_file;
-+ }
-+ pfile->owner = THIS_MODULE;
-+
-+ return usb_gadget_register_driver (&zero_driver);
-+
-+ no_file:
-+ remove_proc_entry("isoc_data", NULL);
-+ done:
-+ return retval;
-+}
-+module_init (init);
-+
-+static void __exit cleanup (void)
-+{
-+
-+ usb_gadget_unregister_driver (&zero_driver);
-+
-+ remove_proc_entry("isoc_data", pdir);
-+ remove_proc_entry("isoc_test", NULL);
-+}
-+module_exit (cleanup);
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_cfi_common.h
-@@ -0,0 +1,142 @@
-+/* ==========================================================================
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+
-+#if !defined(__DWC_CFI_COMMON_H__)
-+#define __DWC_CFI_COMMON_H__
-+
-+//#include <linux/types.h>
-+
-+/**
-+ * @file
-+ *
-+ * This file contains the CFI specific common constants, interfaces
-+ * (functions and macros) and structures for Linux. No PCD specific
-+ * data structure or definition is to be included in this file.
-+ *
-+ */
-+
-+/** This is a request for all Core Features */
-+#define VEN_CORE_GET_FEATURES 0xB1
-+
-+/** This is a request to get the value of a specific Core Feature */
-+#define VEN_CORE_GET_FEATURE 0xB2
-+
-+/** This command allows the host to set the value of a specific Core Feature */
-+#define VEN_CORE_SET_FEATURE 0xB3
-+
-+/** This command allows the host to set the default values of
-+ * either all or any specific Core Feature
-+ */
-+#define VEN_CORE_RESET_FEATURES 0xB4
-+
-+/** This command forces the PCD to write the deferred values of a Core Features */
-+#define VEN_CORE_ACTIVATE_FEATURES 0xB5
-+
-+/** This request reads a DWORD value from a register at the specified offset */
-+#define VEN_CORE_READ_REGISTER 0xB6
-+
-+/** This request writes a DWORD value into a register at the specified offset */
-+#define VEN_CORE_WRITE_REGISTER 0xB7
-+
-+/** This structure is the header of the Core Features dataset returned to
-+ * the Host
-+ */
-+struct cfi_all_features_header {
-+/** The features header structure length is */
-+#define CFI_ALL_FEATURES_HDR_LEN 8
-+ /**
-+ * The total length of the features dataset returned to the Host
-+ */
-+ uint16_t wTotalLen;
-+
-+ /**
-+ * CFI version number inBinary-Coded Decimal (i.e., 1.00 is 100H).
-+ * This field identifies the version of the CFI Specification with which
-+ * the device is compliant.
-+ */
-+ uint16_t wVersion;
-+
-+ /** The ID of the Core */
-+ uint16_t wCoreID;
-+#define CFI_CORE_ID_UDC 1
-+#define CFI_CORE_ID_OTG 2
-+#define CFI_CORE_ID_WUDEV 3
-+
-+ /** Number of features returned by VEN_CORE_GET_FEATURES request */
-+ uint16_t wNumFeatures;
-+} UPACKED;
-+
-+typedef struct cfi_all_features_header cfi_all_features_header_t;
-+
-+/** This structure is a header of the Core Feature descriptor dataset returned to
-+ * the Host after the VEN_CORE_GET_FEATURES request
-+ */
-+struct cfi_feature_desc_header {
-+#define CFI_FEATURE_DESC_HDR_LEN 8
-+
-+ /** The feature ID */
-+ uint16_t wFeatureID;
-+
-+ /** Length of this feature descriptor in bytes - including the
-+ * length of the feature name string
-+ */
-+ uint16_t wLength;
-+
-+ /** The data length of this feature in bytes */
-+ uint16_t wDataLength;
-+
-+ /**
-+ * Attributes of this features
-+ * D0: Access rights
-+ * 0 - Read/Write
-+ * 1 - Read only
-+ */
-+ uint8_t bmAttributes;
-+#define CFI_FEATURE_ATTR_RO 1
-+#define CFI_FEATURE_ATTR_RW 0
-+
-+ /** Length of the feature name in bytes */
-+ uint8_t bNameLen;
-+
-+ /** The feature name buffer */
-+ //uint8_t *name;
-+} UPACKED;
-+
-+typedef struct cfi_feature_desc_header cfi_feature_desc_header_t;
-+
-+/**
-+ * This structure describes a NULL terminated string referenced by its id field.
-+ * It is very similar to usb_string structure but has the id field type set to 16-bit.
-+ */
-+struct cfi_string {
-+ uint16_t id;
-+ const uint8_t *s;
-+};
-+typedef struct cfi_string cfi_string_t;
-+
-+#endif
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_adp.c
-@@ -0,0 +1,854 @@
-+/* ==========================================================================
-+ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_adp.c $
-+ * $Revision: #12 $
-+ * $Date: 2011/10/26 $
-+ * $Change: 1873028 $
-+ *
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+
-+#include "dwc_os.h"
-+#include "dwc_otg_regs.h"
-+#include "dwc_otg_cil.h"
-+#include "dwc_otg_adp.h"
-+
-+/** @file
-+ *
-+ * This file contains the most of the Attach Detect Protocol implementation for
-+ * the driver to support OTG Rev2.0.
-+ *
-+ */
-+
-+void dwc_otg_adp_write_reg(dwc_otg_core_if_t * core_if, uint32_t value)
-+{
-+ adpctl_data_t adpctl;
-+
-+ adpctl.d32 = value;
-+ adpctl.b.ar = 0x2;
-+
-+ DWC_WRITE_REG32(&core_if->core_global_regs->adpctl, adpctl.d32);
-+
-+ while (adpctl.b.ar) {
-+ adpctl.d32 = DWC_READ_REG32(&core_if->core_global_regs->adpctl);
-+ }
-+
-+}
-+
-+/**
-+ * Function is called to read ADP registers
-+ */
-+uint32_t dwc_otg_adp_read_reg(dwc_otg_core_if_t * core_if)
-+{
-+ adpctl_data_t adpctl;
-+
-+ adpctl.d32 = 0;
-+ adpctl.b.ar = 0x1;
-+
-+ DWC_WRITE_REG32(&core_if->core_global_regs->adpctl, adpctl.d32);
-+
-+ while (adpctl.b.ar) {
-+ adpctl.d32 = DWC_READ_REG32(&core_if->core_global_regs->adpctl);
-+ }
-+
-+ return adpctl.d32;
-+}
-+
-+/**
-+ * Function is called to read ADPCTL register and filter Write-clear bits
-+ */
-+uint32_t dwc_otg_adp_read_reg_filter(dwc_otg_core_if_t * core_if)
-+{
-+ adpctl_data_t adpctl;
-+
-+ adpctl.d32 = dwc_otg_adp_read_reg(core_if);
-+ adpctl.b.adp_tmout_int = 0;
-+ adpctl.b.adp_prb_int = 0;
-+ adpctl.b.adp_tmout_int = 0;
-+
-+ return adpctl.d32;
-+}
-+
-+/**
-+ * Function is called to write ADP registers
-+ */
-+void dwc_otg_adp_modify_reg(dwc_otg_core_if_t * core_if, uint32_t clr,
-+ uint32_t set)
-+{
-+ dwc_otg_adp_write_reg(core_if,
-+ (dwc_otg_adp_read_reg(core_if) & (~clr)) | set);
-+}
-+
-+static void adp_sense_timeout(void *ptr)
-+{
-+ dwc_otg_core_if_t *core_if = (dwc_otg_core_if_t *) ptr;
-+ core_if->adp.sense_timer_started = 0;
-+ DWC_PRINTF("ADP SENSE TIMEOUT\n");
-+ if (core_if->adp_enable) {
-+ dwc_otg_adp_sense_stop(core_if);
-+ dwc_otg_adp_probe_start(core_if);
-+ }
-+}
-+
-+/**
-+ * This function is called when the ADP vbus timer expires. Timeout is 1.1s.
-+ */
-+static void adp_vbuson_timeout(void *ptr)
-+{
-+ gpwrdn_data_t gpwrdn;
-+ dwc_otg_core_if_t *core_if = (dwc_otg_core_if_t *) ptr;
-+ hprt0_data_t hprt0 = {.d32 = 0 };
-+ pcgcctl_data_t pcgcctl = {.d32 = 0 };
-+ DWC_PRINTF("%s: 1.1 seconds expire after turning on VBUS\n",__FUNCTION__);
-+ if (core_if) {
-+ core_if->adp.vbuson_timer_started = 0;
-+ /* Turn off vbus */
-+ hprt0.b.prtpwr = 1;
-+ DWC_MODIFY_REG32(core_if->host_if->hprt0, hprt0.d32, 0);
-+ gpwrdn.d32 = 0;
-+
-+ /* Power off the core */
-+ if (core_if->power_down == 2) {
-+ /* Enable Wakeup Logic */
-+// gpwrdn.b.wkupactiv = 1;
-+ gpwrdn.b.pmuactv = 0;
-+ gpwrdn.b.pwrdnrstn = 1;
-+ gpwrdn.b.pwrdnclmp = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0,
-+ gpwrdn.d32);
-+
-+ /* Suspend the Phy Clock */
-+ pcgcctl.b.stoppclk = 1;
-+ DWC_MODIFY_REG32(core_if->pcgcctl, 0, pcgcctl.d32);
-+
-+ /* Switch on VDD */
-+// gpwrdn.b.wkupactiv = 1;
-+ gpwrdn.b.pmuactv = 1;
-+ gpwrdn.b.pwrdnrstn = 1;
-+ gpwrdn.b.pwrdnclmp = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0,
-+ gpwrdn.d32);
-+ } else {
-+ /* Enable Power Down Logic */
-+ gpwrdn.b.pmuintsel = 1;
-+ gpwrdn.b.pmuactv = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32);
-+ }
-+
-+ /* Power off the core */
-+ if (core_if->power_down == 2) {
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnswtch = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn,
-+ gpwrdn.d32, 0);
-+ }
-+
-+ /* Unmask SRP detected interrupt from Power Down Logic */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.srp_det_msk = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32);
-+
-+ dwc_otg_adp_probe_start(core_if);
-+ dwc_otg_dump_global_registers(core_if);
-+ dwc_otg_dump_host_registers(core_if);
-+ }
-+
-+}
-+
-+/**
-+ * Start the ADP Initial Probe timer to detect if Port Connected interrupt is
-+ * not asserted within 1.1 seconds.
-+ *
-+ * @param core_if the pointer to core_if strucure.
-+ */
-+void dwc_otg_adp_vbuson_timer_start(dwc_otg_core_if_t * core_if)
-+{
-+ core_if->adp.vbuson_timer_started = 1;
-+ if (core_if->adp.vbuson_timer)
-+ {
-+ DWC_PRINTF("SCHEDULING VBUSON TIMER\n");
-+ /* 1.1 secs + 60ms necessary for cil_hcd_start*/
-+ DWC_TIMER_SCHEDULE(core_if->adp.vbuson_timer, 1160);
-+ } else {
-+ DWC_WARN("VBUSON_TIMER = %p\n",core_if->adp.vbuson_timer);
-+ }
-+}
-+
-+#if 0
-+/**
-+ * Masks all DWC OTG core interrupts
-+ *
-+ */
-+static void mask_all_interrupts(dwc_otg_core_if_t * core_if)
-+{
-+ int i;
-+ gahbcfg_data_t ahbcfg = {.d32 = 0 };
-+
-+ /* Mask Host Interrupts */
-+
-+ /* Clear and disable HCINTs */
-+ for (i = 0; i < core_if->core_params->host_channels; i++) {
-+ DWC_WRITE_REG32(&core_if->host_if->hc_regs[i]->hcintmsk, 0);
-+ DWC_WRITE_REG32(&core_if->host_if->hc_regs[i]->hcint, 0xFFFFFFFF);
-+
-+ }
-+
-+ /* Clear and disable HAINT */
-+ DWC_WRITE_REG32(&core_if->host_if->host_global_regs->haintmsk, 0x0000);
-+ DWC_WRITE_REG32(&core_if->host_if->host_global_regs->haint, 0xFFFFFFFF);
-+
-+ /* Mask Device Interrupts */
-+ if (!core_if->multiproc_int_enable) {
-+ /* Clear and disable IN Endpoint interrupts */
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->diepmsk, 0);
-+ for (i = 0; i <= core_if->dev_if->num_in_eps; i++) {
-+ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[i]->
-+ diepint, 0xFFFFFFFF);
-+ }
-+
-+ /* Clear and disable OUT Endpoint interrupts */
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->doepmsk, 0);
-+ for (i = 0; i <= core_if->dev_if->num_out_eps; i++) {
-+ DWC_WRITE_REG32(&core_if->dev_if->out_ep_regs[i]->
-+ doepint, 0xFFFFFFFF);
-+ }
-+
-+ /* Clear and disable DAINT */
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->daint,
-+ 0xFFFFFFFF);
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->daintmsk, 0);
-+ } else {
-+ for (i = 0; i < core_if->dev_if->num_in_eps; ++i) {
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->
-+ diepeachintmsk[i], 0);
-+ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[i]->
-+ diepint, 0xFFFFFFFF);
-+ }
-+
-+ for (i = 0; i < core_if->dev_if->num_out_eps; ++i) {
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->
-+ doepeachintmsk[i], 0);
-+ DWC_WRITE_REG32(&core_if->dev_if->out_ep_regs[i]->
-+ doepint, 0xFFFFFFFF);
-+ }
-+
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->deachintmsk,
-+ 0);
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->deachint,
-+ 0xFFFFFFFF);
-+
-+ }
-+
-+ /* Disable interrupts */
-+ ahbcfg.b.glblintrmsk = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gahbcfg, ahbcfg.d32, 0);
-+
-+ /* Disable all interrupts. */
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintmsk, 0);
-+
-+ /* Clear any pending interrupts */
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, 0xFFFFFFFF);
-+
-+ /* Clear any pending OTG Interrupts */
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gotgint, 0xFFFFFFFF);
-+}
-+
-+/**
-+ * Unmask Port Connection Detected interrupt
-+ *
-+ */
-+static void unmask_conn_det_intr(dwc_otg_core_if_t * core_if)
-+{
-+ gintmsk_data_t gintmsk = {.d32 = 0,.b.portintr = 1 };
-+
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintmsk, gintmsk.d32);
-+}
-+#endif
-+
-+/**
-+ * Starts the ADP Probing
-+ *
-+ * @param core_if the pointer to core_if structure.
-+ */
-+uint32_t dwc_otg_adp_probe_start(dwc_otg_core_if_t * core_if)
-+{
-+
-+ adpctl_data_t adpctl = {.d32 = 0};
-+ gpwrdn_data_t gpwrdn;
-+#if 0
-+ adpctl_data_t adpctl_int = {.d32 = 0, .b.adp_prb_int = 1,
-+ .b.adp_sns_int = 1, b.adp_tmout_int};
-+#endif
-+ dwc_otg_disable_global_interrupts(core_if);
-+ DWC_PRINTF("ADP Probe Start\n");
-+ core_if->adp.probe_enabled = 1;
-+
-+ adpctl.b.adpres = 1;
-+ dwc_otg_adp_write_reg(core_if, adpctl.d32);
-+
-+ while (adpctl.b.adpres) {
-+ adpctl.d32 = dwc_otg_adp_read_reg(core_if);
-+ }
-+
-+ adpctl.d32 = 0;
-+ gpwrdn.d32 = DWC_READ_REG32(&core_if->core_global_regs->gpwrdn);
-+
-+ /* In Host mode unmask SRP detected interrupt */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.sts_chngint_msk = 1;
-+ if (!gpwrdn.b.idsts) {
-+ gpwrdn.b.srp_det_msk = 1;
-+ }
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32);
-+
-+ adpctl.b.adp_tmout_int_msk = 1;
-+ adpctl.b.adp_prb_int_msk = 1;
-+ adpctl.b.prb_dschg = 1;
-+ adpctl.b.prb_delta = 1;
-+ adpctl.b.prb_per = 1;
-+ adpctl.b.adpen = 1;
-+ adpctl.b.enaprb = 1;
-+
-+ dwc_otg_adp_write_reg(core_if, adpctl.d32);
-+ DWC_PRINTF("ADP Probe Finish\n");
-+ return 0;
-+}
-+
-+/**
-+ * Starts the ADP Sense timer to detect if ADP Sense interrupt is not asserted
-+ * within 3 seconds.
-+ *
-+ * @param core_if the pointer to core_if strucure.
-+ */
-+void dwc_otg_adp_sense_timer_start(dwc_otg_core_if_t * core_if)
-+{
-+ core_if->adp.sense_timer_started = 1;
-+ DWC_TIMER_SCHEDULE(core_if->adp.sense_timer, 3000 /* 3 secs */ );
-+}
-+
-+/**
-+ * Starts the ADP Sense
-+ *
-+ * @param core_if the pointer to core_if strucure.
-+ */
-+uint32_t dwc_otg_adp_sense_start(dwc_otg_core_if_t * core_if)
-+{
-+ adpctl_data_t adpctl;
-+
-+ DWC_PRINTF("ADP Sense Start\n");
-+
-+ /* Unmask ADP sense interrupt and mask all other from the core */
-+ adpctl.d32 = dwc_otg_adp_read_reg_filter(core_if);
-+ adpctl.b.adp_sns_int_msk = 1;
-+ dwc_otg_adp_write_reg(core_if, adpctl.d32);
-+ dwc_otg_disable_global_interrupts(core_if); // vahrama
-+
-+ /* Set ADP reset bit*/
-+ adpctl.d32 = dwc_otg_adp_read_reg_filter(core_if);
-+ adpctl.b.adpres = 1;
-+ dwc_otg_adp_write_reg(core_if, adpctl.d32);
-+
-+ while (adpctl.b.adpres) {
-+ adpctl.d32 = dwc_otg_adp_read_reg(core_if);
-+ }
-+
-+ adpctl.b.adpres = 0;
-+ adpctl.b.adpen = 1;
-+ adpctl.b.enasns = 1;
-+ dwc_otg_adp_write_reg(core_if, adpctl.d32);
-+
-+ dwc_otg_adp_sense_timer_start(core_if);
-+
-+ return 0;
-+}
-+
-+/**
-+ * Stops the ADP Probing
-+ *
-+ * @param core_if the pointer to core_if strucure.
-+ */
-+uint32_t dwc_otg_adp_probe_stop(dwc_otg_core_if_t * core_if)
-+{
-+
-+ adpctl_data_t adpctl;
-+ DWC_PRINTF("Stop ADP probe\n");
-+ core_if->adp.probe_enabled = 0;
-+ core_if->adp.probe_counter = 0;
-+ adpctl.d32 = dwc_otg_adp_read_reg(core_if);
-+
-+ adpctl.b.adpen = 0;
-+ adpctl.b.adp_prb_int = 1;
-+ adpctl.b.adp_tmout_int = 1;
-+ adpctl.b.adp_sns_int = 1;
-+ dwc_otg_adp_write_reg(core_if, adpctl.d32);
-+
-+ return 0;
-+}
-+
-+/**
-+ * Stops the ADP Sensing
-+ *
-+ * @param core_if the pointer to core_if strucure.
-+ */
-+uint32_t dwc_otg_adp_sense_stop(dwc_otg_core_if_t * core_if)
-+{
-+ adpctl_data_t adpctl;
-+
-+ core_if->adp.sense_enabled = 0;
-+
-+ adpctl.d32 = dwc_otg_adp_read_reg_filter(core_if);
-+ adpctl.b.enasns = 0;
-+ adpctl.b.adp_sns_int = 1;
-+ dwc_otg_adp_write_reg(core_if, adpctl.d32);
-+
-+ return 0;
-+}
-+
-+/**
-+ * Called to turn on the VBUS after initial ADP probe in host mode.
-+ * If port power was already enabled in cil_hcd_start function then
-+ * only schedule a timer.
-+ *
-+ * @param core_if the pointer to core_if structure.
-+ */
-+void dwc_otg_adp_turnon_vbus(dwc_otg_core_if_t * core_if)
-+{
-+ hprt0_data_t hprt0 = {.d32 = 0 };
-+ hprt0.d32 = dwc_otg_read_hprt0(core_if);
-+ DWC_PRINTF("Turn on VBUS for 1.1s, port power is %d\n", hprt0.b.prtpwr);
-+
-+ if (hprt0.b.prtpwr == 0) {
-+ hprt0.b.prtpwr = 1;
-+ //DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+ }
-+
-+ dwc_otg_adp_vbuson_timer_start(core_if);
-+}
-+
-+/**
-+ * Called right after driver is loaded
-+ * to perform initial actions for ADP
-+ *
-+ * @param core_if the pointer to core_if structure.
-+ * @param is_host - flag for current mode of operation either from GINTSTS or GPWRDN
-+ */
-+void dwc_otg_adp_start(dwc_otg_core_if_t * core_if, uint8_t is_host)
-+{
-+ gpwrdn_data_t gpwrdn;
-+
-+ DWC_PRINTF("ADP Initial Start\n");
-+ core_if->adp.adp_started = 1;
-+
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, 0xFFFFFFFF);
-+ dwc_otg_disable_global_interrupts(core_if);
-+ if (is_host) {
-+ DWC_PRINTF("HOST MODE\n");
-+ /* Enable Power Down Logic Interrupt*/
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuintsel = 1;
-+ gpwrdn.b.pmuactv = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32);
-+ /* Initialize first ADP probe to obtain Ramp Time value */
-+ core_if->adp.initial_probe = 1;
-+ dwc_otg_adp_probe_start(core_if);
-+ } else {
-+ gotgctl_data_t gotgctl;
-+ gotgctl.d32 = DWC_READ_REG32(&core_if->core_global_regs->gotgctl);
-+ DWC_PRINTF("DEVICE MODE\n");
-+ if (gotgctl.b.bsesvld == 0) {
-+ /* Enable Power Down Logic Interrupt*/
-+ gpwrdn.d32 = 0;
-+ DWC_PRINTF("VBUS is not valid - start ADP probe\n");
-+ gpwrdn.b.pmuintsel = 1;
-+ gpwrdn.b.pmuactv = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32);
-+ core_if->adp.initial_probe = 1;
-+ dwc_otg_adp_probe_start(core_if);
-+ } else {
-+ DWC_PRINTF("VBUS is valid - initialize core as a Device\n");
-+ core_if->op_state = B_PERIPHERAL;
-+ dwc_otg_core_init(core_if);
-+ dwc_otg_enable_global_interrupts(core_if);
-+ cil_pcd_start(core_if);
-+ dwc_otg_dump_global_registers(core_if);
-+ dwc_otg_dump_dev_registers(core_if);
-+ }
-+ }
-+}
-+
-+void dwc_otg_adp_init(dwc_otg_core_if_t * core_if)
-+{
-+ core_if->adp.adp_started = 0;
-+ core_if->adp.initial_probe = 0;
-+ core_if->adp.probe_timer_values[0] = -1;
-+ core_if->adp.probe_timer_values[1] = -1;
-+ core_if->adp.probe_enabled = 0;
-+ core_if->adp.sense_enabled = 0;
-+ core_if->adp.sense_timer_started = 0;
-+ core_if->adp.vbuson_timer_started = 0;
-+ core_if->adp.probe_counter = 0;
-+ core_if->adp.gpwrdn = 0;
-+ core_if->adp.attached = DWC_OTG_ADP_UNKOWN;
-+ /* Initialize timers */
-+ core_if->adp.sense_timer =
-+ DWC_TIMER_ALLOC("ADP SENSE TIMER", adp_sense_timeout, core_if);
-+ core_if->adp.vbuson_timer =
-+ DWC_TIMER_ALLOC("ADP VBUS ON TIMER", adp_vbuson_timeout, core_if);
-+ if (!core_if->adp.sense_timer || !core_if->adp.vbuson_timer)
-+ {
-+ DWC_ERROR("Could not allocate memory for ADP timers\n");
-+ }
-+}
-+
-+void dwc_otg_adp_remove(dwc_otg_core_if_t * core_if)
-+{
-+ gpwrdn_data_t gpwrdn = { .d32 = 0 };
-+ gpwrdn.b.pmuintsel = 1;
-+ gpwrdn.b.pmuactv = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+
-+ if (core_if->adp.probe_enabled)
-+ dwc_otg_adp_probe_stop(core_if);
-+ if (core_if->adp.sense_enabled)
-+ dwc_otg_adp_sense_stop(core_if);
-+ if (core_if->adp.sense_timer_started)
-+ DWC_TIMER_CANCEL(core_if->adp.sense_timer);
-+ if (core_if->adp.vbuson_timer_started)
-+ DWC_TIMER_CANCEL(core_if->adp.vbuson_timer);
-+ DWC_TIMER_FREE(core_if->adp.sense_timer);
-+ DWC_TIMER_FREE(core_if->adp.vbuson_timer);
-+}
-+
-+/////////////////////////////////////////////////////////////////////
-+////////////// ADP Interrupt Handlers ///////////////////////////////
-+/////////////////////////////////////////////////////////////////////
-+/**
-+ * This function sets Ramp Timer values
-+ */
-+static uint32_t set_timer_value(dwc_otg_core_if_t * core_if, uint32_t val)
-+{
-+ if (core_if->adp.probe_timer_values[0] == -1) {
-+ core_if->adp.probe_timer_values[0] = val;
-+ core_if->adp.probe_timer_values[1] = -1;
-+ return 1;
-+ } else {
-+ core_if->adp.probe_timer_values[1] =
-+ core_if->adp.probe_timer_values[0];
-+ core_if->adp.probe_timer_values[0] = val;
-+ return 0;
-+ }
-+}
-+
-+/**
-+ * This function compares Ramp Timer values
-+ */
-+static uint32_t compare_timer_values(dwc_otg_core_if_t * core_if)
-+{
-+ uint32_t diff;
-+ if (core_if->adp.probe_timer_values[0]>=core_if->adp.probe_timer_values[1])
-+ diff = core_if->adp.probe_timer_values[0]-core_if->adp.probe_timer_values[1];
-+ else
-+ diff = core_if->adp.probe_timer_values[1]-core_if->adp.probe_timer_values[0];
-+ if(diff < 2) {
-+ return 0;
-+ } else {
-+ return 1;
-+ }
-+}
-+
-+/**
-+ * This function handles ADP Probe Interrupts
-+ */
-+static int32_t dwc_otg_adp_handle_prb_intr(dwc_otg_core_if_t * core_if,
-+ uint32_t val)
-+{
-+ adpctl_data_t adpctl = {.d32 = 0 };
-+ gpwrdn_data_t gpwrdn, temp;
-+ adpctl.d32 = val;
-+
-+ temp.d32 = DWC_READ_REG32(&core_if->core_global_regs->gpwrdn);
-+ core_if->adp.probe_counter++;
-+ core_if->adp.gpwrdn = DWC_READ_REG32(&core_if->core_global_regs->gpwrdn);
-+ if (adpctl.b.rtim == 0 && !temp.b.idsts){
-+ DWC_PRINTF("RTIM value is 0\n");
-+ goto exit;
-+ }
-+ if (set_timer_value(core_if, adpctl.b.rtim) &&
-+ core_if->adp.initial_probe) {
-+ core_if->adp.initial_probe = 0;
-+ dwc_otg_adp_probe_stop(core_if);
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuactv = 1;
-+ gpwrdn.b.pmuintsel = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, 0xFFFFFFFF);
-+
-+ /* check which value is for device mode and which for Host mode */
-+ if (!temp.b.idsts) { /* considered host mode value is 0 */
-+ /*
-+ * Turn on VBUS after initial ADP probe.
-+ */
-+ core_if->op_state = A_HOST;
-+ dwc_otg_enable_global_interrupts(core_if);
-+ DWC_SPINUNLOCK(core_if->lock);
-+ cil_hcd_start(core_if);
-+ dwc_otg_adp_turnon_vbus(core_if);
-+ DWC_SPINLOCK(core_if->lock);
-+ } else {
-+ /*
-+ * Initiate SRP after initial ADP probe.
-+ */
-+ dwc_otg_enable_global_interrupts(core_if);
-+ dwc_otg_initiate_srp(core_if);
-+ }
-+ } else if (core_if->adp.probe_counter > 2){
-+ gpwrdn.d32 = DWC_READ_REG32(&core_if->core_global_regs->gpwrdn);
-+ if (compare_timer_values(core_if)) {
-+ DWC_PRINTF("Difference in timer values !!! \n");
-+// core_if->adp.attached = DWC_OTG_ADP_ATTACHED;
-+ dwc_otg_adp_probe_stop(core_if);
-+
-+ /* Power on the core */
-+ if (core_if->power_down == 2) {
-+ gpwrdn.b.pwrdnswtch = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->
-+ gpwrdn, 0, gpwrdn.d32);
-+ }
-+
-+ /* check which value is for device mode and which for Host mode */
-+ if (!temp.b.idsts) { /* considered host mode value is 0 */
-+ /* Disable Interrupt from Power Down Logic */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuintsel = 1;
-+ gpwrdn.b.pmuactv = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->
-+ gpwrdn, gpwrdn.d32, 0);
-+
-+ /*
-+ * Initialize the Core for Host mode.
-+ */
-+ core_if->op_state = A_HOST;
-+ dwc_otg_core_init(core_if);
-+ dwc_otg_enable_global_interrupts(core_if);
-+ cil_hcd_start(core_if);
-+ } else {
-+ gotgctl_data_t gotgctl;
-+ /* Mask SRP detected interrupt from Power Down Logic */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.srp_det_msk = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->
-+ gpwrdn, gpwrdn.d32, 0);
-+
-+ /* Disable Power Down Logic */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuintsel = 1;
-+ gpwrdn.b.pmuactv = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->
-+ gpwrdn, gpwrdn.d32, 0);
-+
-+ /*
-+ * Initialize the Core for Device mode.
-+ */
-+ core_if->op_state = B_PERIPHERAL;
-+ dwc_otg_core_init(core_if);
-+ dwc_otg_enable_global_interrupts(core_if);
-+ cil_pcd_start(core_if);
-+
-+ gotgctl.d32 = DWC_READ_REG32(&core_if->core_global_regs->gotgctl);
-+ if (!gotgctl.b.bsesvld) {
-+ dwc_otg_initiate_srp(core_if);
-+ }
-+ }
-+ }
-+ if (core_if->power_down == 2) {
-+ if (gpwrdn.b.bsessvld) {
-+ /* Mask SRP detected interrupt from Power Down Logic */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.srp_det_msk = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+
-+ /* Disable Power Down Logic */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuactv = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+
-+ /*
-+ * Initialize the Core for Device mode.
-+ */
-+ core_if->op_state = B_PERIPHERAL;
-+ dwc_otg_core_init(core_if);
-+ dwc_otg_enable_global_interrupts(core_if);
-+ cil_pcd_start(core_if);
-+ }
-+ }
-+ }
-+exit:
-+ /* Clear interrupt */
-+ adpctl.d32 = dwc_otg_adp_read_reg(core_if);
-+ adpctl.b.adp_prb_int = 1;
-+ dwc_otg_adp_write_reg(core_if, adpctl.d32);
-+
-+ return 0;
-+}
-+
-+/**
-+ * This function hadles ADP Sense Interrupt
-+ */
-+static int32_t dwc_otg_adp_handle_sns_intr(dwc_otg_core_if_t * core_if)
-+{
-+ adpctl_data_t adpctl;
-+ /* Stop ADP Sense timer */
-+ DWC_TIMER_CANCEL(core_if->adp.sense_timer);
-+
-+ /* Restart ADP Sense timer */
-+ dwc_otg_adp_sense_timer_start(core_if);
-+
-+ /* Clear interrupt */
-+ adpctl.d32 = dwc_otg_adp_read_reg(core_if);
-+ adpctl.b.adp_sns_int = 1;
-+ dwc_otg_adp_write_reg(core_if, adpctl.d32);
-+
-+ return 0;
-+}
-+
-+/**
-+ * This function handles ADP Probe Interrupts
-+ */
-+static int32_t dwc_otg_adp_handle_prb_tmout_intr(dwc_otg_core_if_t * core_if,
-+ uint32_t val)
-+{
-+ adpctl_data_t adpctl = {.d32 = 0 };
-+ adpctl.d32 = val;
-+ set_timer_value(core_if, adpctl.b.rtim);
-+
-+ /* Clear interrupt */
-+ adpctl.d32 = dwc_otg_adp_read_reg(core_if);
-+ adpctl.b.adp_tmout_int = 1;
-+ dwc_otg_adp_write_reg(core_if, adpctl.d32);
-+
-+ return 0;
-+}
-+
-+/**
-+ * ADP Interrupt handler.
-+ *
-+ */
-+int32_t dwc_otg_adp_handle_intr(dwc_otg_core_if_t * core_if)
-+{
-+ int retval = 0;
-+ adpctl_data_t adpctl = {.d32 = 0};
-+
-+ adpctl.d32 = dwc_otg_adp_read_reg(core_if);
-+ DWC_PRINTF("ADPCTL = %08x\n",adpctl.d32);
-+
-+ if (adpctl.b.adp_sns_int & adpctl.b.adp_sns_int_msk) {
-+ DWC_PRINTF("ADP Sense interrupt\n");
-+ retval |= dwc_otg_adp_handle_sns_intr(core_if);
-+ }
-+ if (adpctl.b.adp_tmout_int & adpctl.b.adp_tmout_int_msk) {
-+ DWC_PRINTF("ADP timeout interrupt\n");
-+ retval |= dwc_otg_adp_handle_prb_tmout_intr(core_if, adpctl.d32);
-+ }
-+ if (adpctl.b.adp_prb_int & adpctl.b.adp_prb_int_msk) {
-+ DWC_PRINTF("ADP Probe interrupt\n");
-+ adpctl.b.adp_prb_int = 1;
-+ retval |= dwc_otg_adp_handle_prb_intr(core_if, adpctl.d32);
-+ }
-+
-+// dwc_otg_adp_modify_reg(core_if, adpctl.d32, 0);
-+ //dwc_otg_adp_write_reg(core_if, adpctl.d32);
-+ DWC_PRINTF("RETURN FROM ADP ISR\n");
-+
-+ return retval;
-+}
-+
-+/**
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ */
-+int32_t dwc_otg_adp_handle_srp_intr(dwc_otg_core_if_t * core_if)
-+{
-+
-+#ifndef DWC_HOST_ONLY
-+ hprt0_data_t hprt0;
-+ gpwrdn_data_t gpwrdn;
-+ DWC_DEBUGPL(DBG_ANY, "++ Power Down Logic Session Request Interrupt++\n");
-+
-+ gpwrdn.d32 = DWC_READ_REG32(&core_if->core_global_regs->gpwrdn);
-+ /* check which value is for device mode and which for Host mode */
-+ if (!gpwrdn.b.idsts) { /* considered host mode value is 0 */
-+ DWC_PRINTF("SRP: Host mode\n");
-+
-+ if (core_if->adp_enable) {
-+ dwc_otg_adp_probe_stop(core_if);
-+
-+ /* Power on the core */
-+ if (core_if->power_down == 2) {
-+ gpwrdn.b.pwrdnswtch = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->
-+ gpwrdn, 0, gpwrdn.d32);
-+ }
-+
-+ core_if->op_state = A_HOST;
-+ dwc_otg_core_init(core_if);
-+ dwc_otg_enable_global_interrupts(core_if);
-+ cil_hcd_start(core_if);
-+ }
-+
-+ /* Turn on the port power bit. */
-+ hprt0.d32 = dwc_otg_read_hprt0(core_if);
-+ hprt0.b.prtpwr = 1;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+
-+ /* Start the Connection timer. So a message can be displayed
-+ * if connect does not occur within 10 seconds. */
-+ cil_hcd_session_start(core_if);
-+ } else {
-+ DWC_PRINTF("SRP: Device mode %s\n", __FUNCTION__);
-+ if (core_if->adp_enable) {
-+ dwc_otg_adp_probe_stop(core_if);
-+
-+ /* Power on the core */
-+ if (core_if->power_down == 2) {
-+ gpwrdn.b.pwrdnswtch = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->
-+ gpwrdn, 0, gpwrdn.d32);
-+ }
-+
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuactv = 0;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0,
-+ gpwrdn.d32);
-+
-+ core_if->op_state = B_PERIPHERAL;
-+ dwc_otg_core_init(core_if);
-+ dwc_otg_enable_global_interrupts(core_if);
-+ cil_pcd_start(core_if);
-+ }
-+ }
-+#endif
-+ return 1;
-+}
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_adp.h
-@@ -0,0 +1,80 @@
-+/* ==========================================================================
-+ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_adp.h $
-+ * $Revision: #7 $
-+ * $Date: 2011/10/24 $
-+ * $Change: 1871159 $
-+ *
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+
-+#ifndef __DWC_OTG_ADP_H__
-+#define __DWC_OTG_ADP_H__
-+
-+/**
-+ * @file
-+ *
-+ * This file contains the Attach Detect Protocol interfaces and defines
-+ * (functions) and structures for Linux.
-+ *
-+ */
-+
-+#define DWC_OTG_ADP_UNATTACHED 0
-+#define DWC_OTG_ADP_ATTACHED 1
-+#define DWC_OTG_ADP_UNKOWN 2
-+
-+typedef struct dwc_otg_adp {
-+ uint32_t adp_started;
-+ uint32_t initial_probe;
-+ int32_t probe_timer_values[2];
-+ uint32_t probe_enabled;
-+ uint32_t sense_enabled;
-+ dwc_timer_t *sense_timer;
-+ uint32_t sense_timer_started;
-+ dwc_timer_t *vbuson_timer;
-+ uint32_t vbuson_timer_started;
-+ uint32_t attached;
-+ uint32_t probe_counter;
-+ uint32_t gpwrdn;
-+} dwc_otg_adp_t;
-+
-+/**
-+ * Attach Detect Protocol functions
-+ */
-+
-+extern void dwc_otg_adp_write_reg(dwc_otg_core_if_t * core_if, uint32_t value);
-+extern uint32_t dwc_otg_adp_read_reg(dwc_otg_core_if_t * core_if);
-+extern uint32_t dwc_otg_adp_probe_start(dwc_otg_core_if_t * core_if);
-+extern uint32_t dwc_otg_adp_sense_start(dwc_otg_core_if_t * core_if);
-+extern uint32_t dwc_otg_adp_probe_stop(dwc_otg_core_if_t * core_if);
-+extern uint32_t dwc_otg_adp_sense_stop(dwc_otg_core_if_t * core_if);
-+extern void dwc_otg_adp_start(dwc_otg_core_if_t * core_if, uint8_t is_host);
-+extern void dwc_otg_adp_init(dwc_otg_core_if_t * core_if);
-+extern void dwc_otg_adp_remove(dwc_otg_core_if_t * core_if);
-+extern int32_t dwc_otg_adp_handle_intr(dwc_otg_core_if_t * core_if);
-+extern int32_t dwc_otg_adp_handle_srp_intr(dwc_otg_core_if_t * core_if);
-+
-+#endif //__DWC_OTG_ADP_H__
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_attr.c
-@@ -0,0 +1,1210 @@
-+/* ==========================================================================
-+ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_attr.c $
-+ * $Revision: #44 $
-+ * $Date: 2010/11/29 $
-+ * $Change: 1636033 $
-+ *
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+
-+/** @file
-+ *
-+ * The diagnostic interface will provide access to the controller for
-+ * bringing up the hardware and testing. The Linux driver attributes
-+ * feature will be used to provide the Linux Diagnostic
-+ * Interface. These attributes are accessed through sysfs.
-+ */
-+
-+/** @page "Linux Module Attributes"
-+ *
-+ * The Linux module attributes feature is used to provide the Linux
-+ * Diagnostic Interface. These attributes are accessed through sysfs.
-+ * The diagnostic interface will provide access to the controller for
-+ * bringing up the hardware and testing.
-+
-+ The following table shows the attributes.
-+ <table>
-+ <tr>
-+ <td><b> Name</b></td>
-+ <td><b> Description</b></td>
-+ <td><b> Access</b></td>
-+ </tr>
-+
-+ <tr>
-+ <td> mode </td>
-+ <td> Returns the current mode: 0 for device mode, 1 for host mode</td>
-+ <td> Read</td>
-+ </tr>
-+
-+ <tr>
-+ <td> hnpcapable </td>
-+ <td> Gets or sets the "HNP-capable" bit in the Core USB Configuraton Register.
-+ Read returns the current value.</td>
-+ <td> Read/Write</td>
-+ </tr>
-+
-+ <tr>
-+ <td> srpcapable </td>
-+ <td> Gets or sets the "SRP-capable" bit in the Core USB Configuraton Register.
-+ Read returns the current value.</td>
-+ <td> Read/Write</td>
-+ </tr>
-+
-+ <tr>
-+ <td> hsic_connect </td>
-+ <td> Gets or sets the "HSIC-Connect" bit in the GLPMCFG Register.
-+ Read returns the current value.</td>
-+ <td> Read/Write</td>
-+ </tr>
-+
-+ <tr>
-+ <td> inv_sel_hsic </td>
-+ <td> Gets or sets the "Invert Select HSIC" bit in the GLPMFG Register.
-+ Read returns the current value.</td>
-+ <td> Read/Write</td>
-+ </tr>
-+
-+ <tr>
-+ <td> hnp </td>
-+ <td> Initiates the Host Negotiation Protocol. Read returns the status.</td>
-+ <td> Read/Write</td>
-+ </tr>
-+
-+ <tr>
-+ <td> srp </td>
-+ <td> Initiates the Session Request Protocol. Read returns the status.</td>
-+ <td> Read/Write</td>
-+ </tr>
-+
-+ <tr>
-+ <td> buspower </td>
-+ <td> Gets or sets the Power State of the bus (0 - Off or 1 - On)</td>
-+ <td> Read/Write</td>
-+ </tr>
-+
-+ <tr>
-+ <td> bussuspend </td>
-+ <td> Suspends the USB bus.</td>
-+ <td> Read/Write</td>
-+ </tr>
-+
-+ <tr>
-+ <td> busconnected </td>
-+ <td> Gets the connection status of the bus</td>
-+ <td> Read</td>
-+ </tr>
-+
-+ <tr>
-+ <td> gotgctl </td>
-+ <td> Gets or sets the Core Control Status Register.</td>
-+ <td> Read/Write</td>
-+ </tr>
-+
-+ <tr>
-+ <td> gusbcfg </td>
-+ <td> Gets or sets the Core USB Configuration Register</td>
-+ <td> Read/Write</td>
-+ </tr>
-+
-+ <tr>
-+ <td> grxfsiz </td>
-+ <td> Gets or sets the Receive FIFO Size Register</td>
-+ <td> Read/Write</td>
-+ </tr>
-+
-+ <tr>
-+ <td> gnptxfsiz </td>
-+ <td> Gets or sets the non-periodic Transmit Size Register</td>
-+ <td> Read/Write</td>
-+ </tr>
-+
-+ <tr>
-+ <td> gpvndctl </td>
-+ <td> Gets or sets the PHY Vendor Control Register</td>
-+ <td> Read/Write</td>
-+ </tr>
-+
-+ <tr>
-+ <td> ggpio </td>
-+ <td> Gets the value in the lower 16-bits of the General Purpose IO Register
-+ or sets the upper 16 bits.</td>
-+ <td> Read/Write</td>
-+ </tr>
-+
-+ <tr>
-+ <td> guid </td>
-+ <td> Gets or sets the value of the User ID Register</td>
-+ <td> Read/Write</td>
-+ </tr>
-+
-+ <tr>
-+ <td> gsnpsid </td>
-+ <td> Gets the value of the Synopsys ID Regester</td>
-+ <td> Read</td>
-+ </tr>
-+
-+ <tr>
-+ <td> devspeed </td>
-+ <td> Gets or sets the device speed setting in the DCFG register</td>
-+ <td> Read/Write</td>
-+ </tr>
-+
-+ <tr>
-+ <td> enumspeed </td>
-+ <td> Gets the device enumeration Speed.</td>
-+ <td> Read</td>
-+ </tr>
-+
-+ <tr>
-+ <td> hptxfsiz </td>
-+ <td> Gets the value of the Host Periodic Transmit FIFO</td>
-+ <td> Read</td>
-+ </tr>
-+
-+ <tr>
-+ <td> hprt0 </td>
-+ <td> Gets or sets the value in the Host Port Control and Status Register</td>
-+ <td> Read/Write</td>
-+ </tr>
-+
-+ <tr>
-+ <td> regoffset </td>
-+ <td> Sets the register offset for the next Register Access</td>
-+ <td> Read/Write</td>
-+ </tr>
-+
-+ <tr>
-+ <td> regvalue </td>
-+ <td> Gets or sets the value of the register at the offset in the regoffset attribute.</td>
-+ <td> Read/Write</td>
-+ </tr>
-+
-+ <tr>
-+ <td> remote_wakeup </td>
-+ <td> On read, shows the status of Remote Wakeup. On write, initiates a remote
-+ wakeup of the host. When bit 0 is 1 and Remote Wakeup is enabled, the Remote
-+ Wakeup signalling bit in the Device Control Register is set for 1
-+ milli-second.</td>
-+ <td> Read/Write</td>
-+ </tr>
-+
-+ <tr>
-+ <td> rem_wakeup_pwrdn </td>
-+ <td> On read, shows the status core - hibernated or not. On write, initiates
-+ a remote wakeup of the device from Hibernation. </td>
-+ <td> Read/Write</td>
-+ </tr>
-+
-+ <tr>
-+ <td> mode_ch_tim_en </td>
-+ <td> This bit is used to enable or disable the host core to wait for 200 PHY
-+ clock cycles at the end of Resume to change the opmode signal to the PHY to 00
-+ after Suspend or LPM. </td>
-+ <td> Read/Write</td>
-+ </tr>
-+
-+ <tr>
-+ <td> fr_interval </td>
-+ <td> On read, shows the value of HFIR Frame Interval. On write, dynamically
-+ reload HFIR register during runtime. The application can write a value to this
-+ register only after the Port Enable bit of the Host Port Control and Status
-+ register (HPRT.PrtEnaPort) has been set </td>
-+ <td> Read/Write</td>
-+ </tr>
-+
-+ <tr>
-+ <td> disconnect_us </td>
-+ <td> On read, shows the status of disconnect_device_us. On write, sets disconnect_us
-+ which causes soft disconnect for 100us. Applicable only for device mode of operation.</td>
-+ <td> Read/Write</td>
-+ </tr>
-+
-+ <tr>
-+ <td> regdump </td>
-+ <td> Dumps the contents of core registers.</td>
-+ <td> Read</td>
-+ </tr>
-+
-+ <tr>
-+ <td> spramdump </td>
-+ <td> Dumps the contents of core registers.</td>
-+ <td> Read</td>
-+ </tr>
-+
-+ <tr>
-+ <td> hcddump </td>
-+ <td> Dumps the current HCD state.</td>
-+ <td> Read</td>
-+ </tr>
-+
-+ <tr>
-+ <td> hcd_frrem </td>
-+ <td> Shows the average value of the Frame Remaining
-+ field in the Host Frame Number/Frame Remaining register when an SOF interrupt
-+ occurs. This can be used to determine the average interrupt latency. Also
-+ shows the average Frame Remaining value for start_transfer and the "a" and
-+ "b" sample points. The "a" and "b" sample points may be used during debugging
-+ bto determine how long it takes to execute a section of the HCD code.</td>
-+ <td> Read</td>
-+ </tr>
-+
-+ <tr>
-+ <td> rd_reg_test </td>
-+ <td> Displays the time required to read the GNPTXFSIZ register many times
-+ (the output shows the number of times the register is read).
-+ <td> Read</td>
-+ </tr>
-+
-+ <tr>
-+ <td> wr_reg_test </td>
-+ <td> Displays the time required to write the GNPTXFSIZ register many times
-+ (the output shows the number of times the register is written).
-+ <td> Read</td>
-+ </tr>
-+
-+ <tr>
-+ <td> lpm_response </td>
-+ <td> Gets or sets lpm_response mode. Applicable only in device mode.
-+ <td> Write</td>
-+ </tr>
-+
-+ <tr>
-+ <td> sleep_status </td>
-+ <td> Shows sleep status of device.
-+ <td> Read</td>
-+ </tr>
-+
-+ </table>
-+
-+ Example usage:
-+ To get the current mode:
-+ cat /sys/devices/lm0/mode
-+
-+ To power down the USB:
-+ echo 0 > /sys/devices/lm0/buspower
-+ */
-+
-+#include "dwc_otg_os_dep.h"
-+#include "dwc_os.h"
-+#include "dwc_otg_driver.h"
-+#include "dwc_otg_attr.h"
-+#include "dwc_otg_core_if.h"
-+#include "dwc_otg_pcd_if.h"
-+#include "dwc_otg_hcd_if.h"
-+
-+/*
-+ * MACROs for defining sysfs attribute
-+ */
-+#ifdef LM_INTERFACE
-+
-+#define DWC_OTG_DEVICE_ATTR_BITFIELD_SHOW(_otg_attr_name_,_string_) \
-+static ssize_t _otg_attr_name_##_show (struct device *_dev, struct device_attribute *attr, char *buf) \
-+{ \
-+ struct lm_device *lm_dev = container_of(_dev, struct lm_device, dev); \
-+ dwc_otg_device_t *otg_dev = lm_get_drvdata(lm_dev); \
-+ uint32_t val; \
-+ val = dwc_otg_get_##_otg_attr_name_ (otg_dev->core_if); \
-+ return sprintf (buf, "%s = 0x%x\n", _string_, val); \
-+}
-+#define DWC_OTG_DEVICE_ATTR_BITFIELD_STORE(_otg_attr_name_,_string_) \
-+static ssize_t _otg_attr_name_##_store (struct device *_dev, struct device_attribute *attr, \
-+ const char *buf, size_t count) \
-+{ \
-+ struct lm_device *lm_dev = container_of(_dev, struct lm_device, dev); \
-+ dwc_otg_device_t *otg_dev = lm_get_drvdata(lm_dev); \
-+ uint32_t set = simple_strtoul(buf, NULL, 16); \
-+ dwc_otg_set_##_otg_attr_name_(otg_dev->core_if, set);\
-+ return count; \
-+}
-+
-+#elif defined(PCI_INTERFACE)
-+
-+#define DWC_OTG_DEVICE_ATTR_BITFIELD_SHOW(_otg_attr_name_,_string_) \
-+static ssize_t _otg_attr_name_##_show (struct device *_dev, struct device_attribute *attr, char *buf) \
-+{ \
-+ dwc_otg_device_t *otg_dev = dev_get_drvdata(_dev); \
-+ uint32_t val; \
-+ val = dwc_otg_get_##_otg_attr_name_ (otg_dev->core_if); \
-+ return sprintf (buf, "%s = 0x%x\n", _string_, val); \
-+}
-+#define DWC_OTG_DEVICE_ATTR_BITFIELD_STORE(_otg_attr_name_,_string_) \
-+static ssize_t _otg_attr_name_##_store (struct device *_dev, struct device_attribute *attr, \
-+ const char *buf, size_t count) \
-+{ \
-+ dwc_otg_device_t *otg_dev = dev_get_drvdata(_dev); \
-+ uint32_t set = simple_strtoul(buf, NULL, 16); \
-+ dwc_otg_set_##_otg_attr_name_(otg_dev->core_if, set);\
-+ return count; \
-+}
-+
-+#elif defined(PLATFORM_INTERFACE)
-+
-+#define DWC_OTG_DEVICE_ATTR_BITFIELD_SHOW(_otg_attr_name_,_string_) \
-+static ssize_t _otg_attr_name_##_show (struct device *_dev, struct device_attribute *attr, char *buf) \
-+{ \
-+ struct platform_device *platform_dev = \
-+ container_of(_dev, struct platform_device, dev); \
-+ dwc_otg_device_t *otg_dev = platform_get_drvdata(platform_dev); \
-+ uint32_t val; \
-+ DWC_PRINTF("%s(%p) -> platform_dev %p, otg_dev %p\n", \
-+ __func__, _dev, platform_dev, otg_dev); \
-+ val = dwc_otg_get_##_otg_attr_name_ (otg_dev->core_if); \
-+ return sprintf (buf, "%s = 0x%x\n", _string_, val); \
-+}
-+#define DWC_OTG_DEVICE_ATTR_BITFIELD_STORE(_otg_attr_name_,_string_) \
-+static ssize_t _otg_attr_name_##_store (struct device *_dev, struct device_attribute *attr, \
-+ const char *buf, size_t count) \
-+{ \
-+ struct platform_device *platform_dev = container_of(_dev, struct platform_device, dev); \
-+ dwc_otg_device_t *otg_dev = platform_get_drvdata(platform_dev); \
-+ uint32_t set = simple_strtoul(buf, NULL, 16); \
-+ dwc_otg_set_##_otg_attr_name_(otg_dev->core_if, set);\
-+ return count; \
-+}
-+#endif
-+
-+/*
-+ * MACROs for defining sysfs attribute for 32-bit registers
-+ */
-+#ifdef LM_INTERFACE
-+#define DWC_OTG_DEVICE_ATTR_REG_SHOW(_otg_attr_name_,_string_) \
-+static ssize_t _otg_attr_name_##_show (struct device *_dev, struct device_attribute *attr, char *buf) \
-+{ \
-+ struct lm_device *lm_dev = container_of(_dev, struct lm_device, dev); \
-+ dwc_otg_device_t *otg_dev = lm_get_drvdata(lm_dev); \
-+ uint32_t val; \
-+ val = dwc_otg_get_##_otg_attr_name_ (otg_dev->core_if); \
-+ return sprintf (buf, "%s = 0x%08x\n", _string_, val); \
-+}
-+#define DWC_OTG_DEVICE_ATTR_REG_STORE(_otg_attr_name_,_string_) \
-+static ssize_t _otg_attr_name_##_store (struct device *_dev, struct device_attribute *attr, \
-+ const char *buf, size_t count) \
-+{ \
-+ struct lm_device *lm_dev = container_of(_dev, struct lm_device, dev); \
-+ dwc_otg_device_t *otg_dev = lm_get_drvdata(lm_dev); \
-+ uint32_t val = simple_strtoul(buf, NULL, 16); \
-+ dwc_otg_set_##_otg_attr_name_ (otg_dev->core_if, val); \
-+ return count; \
-+}
-+#elif defined(PCI_INTERFACE)
-+#define DWC_OTG_DEVICE_ATTR_REG_SHOW(_otg_attr_name_,_string_) \
-+static ssize_t _otg_attr_name_##_show (struct device *_dev, struct device_attribute *attr, char *buf) \
-+{ \
-+ dwc_otg_device_t *otg_dev = dev_get_drvdata(_dev); \
-+ uint32_t val; \
-+ val = dwc_otg_get_##_otg_attr_name_ (otg_dev->core_if); \
-+ return sprintf (buf, "%s = 0x%08x\n", _string_, val); \
-+}
-+#define DWC_OTG_DEVICE_ATTR_REG_STORE(_otg_attr_name_,_string_) \
-+static ssize_t _otg_attr_name_##_store (struct device *_dev, struct device_attribute *attr, \
-+ const char *buf, size_t count) \
-+{ \
-+ dwc_otg_device_t *otg_dev = dev_get_drvdata(_dev); \
-+ uint32_t val = simple_strtoul(buf, NULL, 16); \
-+ dwc_otg_set_##_otg_attr_name_ (otg_dev->core_if, val); \
-+ return count; \
-+}
-+
-+#elif defined(PLATFORM_INTERFACE)
-+#include "dwc_otg_dbg.h"
-+#define DWC_OTG_DEVICE_ATTR_REG_SHOW(_otg_attr_name_,_string_) \
-+static ssize_t _otg_attr_name_##_show (struct device *_dev, struct device_attribute *attr, char *buf) \
-+{ \
-+ struct platform_device *platform_dev = container_of(_dev, struct platform_device, dev); \
-+ dwc_otg_device_t *otg_dev = platform_get_drvdata(platform_dev); \
-+ uint32_t val; \
-+ DWC_PRINTF("%s(%p) -> platform_dev %p, otg_dev %p\n", \
-+ __func__, _dev, platform_dev, otg_dev); \
-+ val = dwc_otg_get_##_otg_attr_name_ (otg_dev->core_if); \
-+ return sprintf (buf, "%s = 0x%08x\n", _string_, val); \
-+}
-+#define DWC_OTG_DEVICE_ATTR_REG_STORE(_otg_attr_name_,_string_) \
-+static ssize_t _otg_attr_name_##_store (struct device *_dev, struct device_attribute *attr, \
-+ const char *buf, size_t count) \
-+{ \
-+ struct platform_device *platform_dev = container_of(_dev, struct platform_device, dev); \
-+ dwc_otg_device_t *otg_dev = platform_get_drvdata(platform_dev); \
-+ uint32_t val = simple_strtoul(buf, NULL, 16); \
-+ dwc_otg_set_##_otg_attr_name_ (otg_dev->core_if, val); \
-+ return count; \
-+}
-+
-+#endif
-+
-+#define DWC_OTG_DEVICE_ATTR_BITFIELD_RW(_otg_attr_name_,_string_) \
-+DWC_OTG_DEVICE_ATTR_BITFIELD_SHOW(_otg_attr_name_,_string_) \
-+DWC_OTG_DEVICE_ATTR_BITFIELD_STORE(_otg_attr_name_,_string_) \
-+DEVICE_ATTR(_otg_attr_name_,0644,_otg_attr_name_##_show,_otg_attr_name_##_store);
-+
-+#define DWC_OTG_DEVICE_ATTR_BITFIELD_RO(_otg_attr_name_,_string_) \
-+DWC_OTG_DEVICE_ATTR_BITFIELD_SHOW(_otg_attr_name_,_string_) \
-+DEVICE_ATTR(_otg_attr_name_,0444,_otg_attr_name_##_show,NULL);
-+
-+#define DWC_OTG_DEVICE_ATTR_REG32_RW(_otg_attr_name_,_addr_,_string_) \
-+DWC_OTG_DEVICE_ATTR_REG_SHOW(_otg_attr_name_,_string_) \
-+DWC_OTG_DEVICE_ATTR_REG_STORE(_otg_attr_name_,_string_) \
-+DEVICE_ATTR(_otg_attr_name_,0644,_otg_attr_name_##_show,_otg_attr_name_##_store);
-+
-+#define DWC_OTG_DEVICE_ATTR_REG32_RO(_otg_attr_name_,_addr_,_string_) \
-+DWC_OTG_DEVICE_ATTR_REG_SHOW(_otg_attr_name_,_string_) \
-+DEVICE_ATTR(_otg_attr_name_,0444,_otg_attr_name_##_show,NULL);
-+
-+/** @name Functions for Show/Store of Attributes */
-+/**@{*/
-+
-+/**
-+ * Helper function returning the otg_device structure of the given device
-+ */
-+static dwc_otg_device_t *dwc_otg_drvdev(struct device *_dev)
-+{
-+ dwc_otg_device_t *otg_dev;
-+ DWC_OTG_GETDRVDEV(otg_dev, _dev);
-+ return otg_dev;
-+}
-+
-+/**
-+ * Show the register offset of the Register Access.
-+ */
-+static ssize_t regoffset_show(struct device *_dev,
-+ struct device_attribute *attr, char *buf)
-+{
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+ return snprintf(buf, sizeof("0xFFFFFFFF\n") + 1, "0x%08x\n",
-+ otg_dev->os_dep.reg_offset);
-+}
-+
-+/**
-+ * Set the register offset for the next Register Access Read/Write
-+ */
-+static ssize_t regoffset_store(struct device *_dev,
-+ struct device_attribute *attr,
-+ const char *buf, size_t count)
-+{
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+ uint32_t offset = simple_strtoul(buf, NULL, 16);
-+#if defined(LM_INTERFACE) || defined(PLATFORM_INTERFACE)
-+ if (offset < SZ_256K) {
-+#elif defined(PCI_INTERFACE)
-+ if (offset < 0x00040000) {
-+#endif
-+ otg_dev->os_dep.reg_offset = offset;
-+ } else {
-+ dev_err(_dev, "invalid offset\n");
-+ }
-+
-+ return count;
-+}
-+
-+DEVICE_ATTR(regoffset, S_IRUGO | S_IWUSR, regoffset_show, regoffset_store);
-+
-+/**
-+ * Show the value of the register at the offset in the reg_offset
-+ * attribute.
-+ */
-+static ssize_t regvalue_show(struct device *_dev,
-+ struct device_attribute *attr, char *buf)
-+{
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+ uint32_t val;
-+ volatile uint32_t *addr;
-+
-+ if (otg_dev->os_dep.reg_offset != 0xFFFFFFFF && 0 != otg_dev->os_dep.base) {
-+ /* Calculate the address */
-+ addr = (uint32_t *) (otg_dev->os_dep.reg_offset +
-+ (uint8_t *) otg_dev->os_dep.base);
-+ val = DWC_READ_REG32(addr);
-+ return snprintf(buf,
-+ sizeof("Reg at 0xFFFFFFFF = 0xFFFFFFFF\n") + 1,
-+ "Reg at 0x%06x = 0x%08x\n", otg_dev->os_dep.reg_offset,
-+ val);
-+ } else {
-+ dev_err(_dev, "Invalid offset (0x%0x)\n", otg_dev->os_dep.reg_offset);
-+ return sprintf(buf, "invalid offset\n");
-+ }
-+}
-+
-+/**
-+ * Store the value in the register at the offset in the reg_offset
-+ * attribute.
-+ *
-+ */
-+static ssize_t regvalue_store(struct device *_dev,
-+ struct device_attribute *attr,
-+ const char *buf, size_t count)
-+{
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+ volatile uint32_t *addr;
-+ uint32_t val = simple_strtoul(buf, NULL, 16);
-+ //dev_dbg(_dev, "Offset=0x%08x Val=0x%08x\n", otg_dev->reg_offset, val);
-+ if (otg_dev->os_dep.reg_offset != 0xFFFFFFFF && 0 != otg_dev->os_dep.base) {
-+ /* Calculate the address */
-+ addr = (uint32_t *) (otg_dev->os_dep.reg_offset +
-+ (uint8_t *) otg_dev->os_dep.base);
-+ DWC_WRITE_REG32(addr, val);
-+ } else {
-+ dev_err(_dev, "Invalid Register Offset (0x%08x)\n",
-+ otg_dev->os_dep.reg_offset);
-+ }
-+ return count;
-+}
-+
-+DEVICE_ATTR(regvalue, S_IRUGO | S_IWUSR, regvalue_show, regvalue_store);
-+
-+/*
-+ * Attributes
-+ */
-+DWC_OTG_DEVICE_ATTR_BITFIELD_RO(mode, "Mode");
-+DWC_OTG_DEVICE_ATTR_BITFIELD_RW(hnpcapable, "HNPCapable");
-+DWC_OTG_DEVICE_ATTR_BITFIELD_RW(srpcapable, "SRPCapable");
-+DWC_OTG_DEVICE_ATTR_BITFIELD_RW(hsic_connect, "HSIC Connect");
-+DWC_OTG_DEVICE_ATTR_BITFIELD_RW(inv_sel_hsic, "Invert Select HSIC");
-+
-+//DWC_OTG_DEVICE_ATTR_BITFIELD_RW(buspower,&(otg_dev->core_if->core_global_regs->gotgctl),(1<<8),8,"Mode");
-+//DWC_OTG_DEVICE_ATTR_BITFIELD_RW(bussuspend,&(otg_dev->core_if->core_global_regs->gotgctl),(1<<8),8,"Mode");
-+DWC_OTG_DEVICE_ATTR_BITFIELD_RO(busconnected, "Bus Connected");
-+
-+DWC_OTG_DEVICE_ATTR_REG32_RW(gotgctl, 0, "GOTGCTL");
-+DWC_OTG_DEVICE_ATTR_REG32_RW(gusbcfg,
-+ &(otg_dev->core_if->core_global_regs->gusbcfg),
-+ "GUSBCFG");
-+DWC_OTG_DEVICE_ATTR_REG32_RW(grxfsiz,
-+ &(otg_dev->core_if->core_global_regs->grxfsiz),
-+ "GRXFSIZ");
-+DWC_OTG_DEVICE_ATTR_REG32_RW(gnptxfsiz,
-+ &(otg_dev->core_if->core_global_regs->gnptxfsiz),
-+ "GNPTXFSIZ");
-+DWC_OTG_DEVICE_ATTR_REG32_RW(gpvndctl,
-+ &(otg_dev->core_if->core_global_regs->gpvndctl),
-+ "GPVNDCTL");
-+DWC_OTG_DEVICE_ATTR_REG32_RW(ggpio,
-+ &(otg_dev->core_if->core_global_regs->ggpio),
-+ "GGPIO");
-+DWC_OTG_DEVICE_ATTR_REG32_RW(guid, &(otg_dev->core_if->core_global_regs->guid),
-+ "GUID");
-+DWC_OTG_DEVICE_ATTR_REG32_RO(gsnpsid,
-+ &(otg_dev->core_if->core_global_regs->gsnpsid),
-+ "GSNPSID");
-+DWC_OTG_DEVICE_ATTR_BITFIELD_RW(devspeed, "Device Speed");
-+DWC_OTG_DEVICE_ATTR_BITFIELD_RO(enumspeed, "Device Enumeration Speed");
-+
-+DWC_OTG_DEVICE_ATTR_REG32_RO(hptxfsiz,
-+ &(otg_dev->core_if->core_global_regs->hptxfsiz),
-+ "HPTXFSIZ");
-+DWC_OTG_DEVICE_ATTR_REG32_RW(hprt0, otg_dev->core_if->host_if->hprt0, "HPRT0");
-+
-+/**
-+ * @todo Add code to initiate the HNP.
-+ */
-+/**
-+ * Show the HNP status bit
-+ */
-+static ssize_t hnp_show(struct device *_dev,
-+ struct device_attribute *attr, char *buf)
-+{
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+ return sprintf(buf, "HstNegScs = 0x%x\n",
-+ dwc_otg_get_hnpstatus(otg_dev->core_if));
-+}
-+
-+/**
-+ * Set the HNP Request bit
-+ */
-+static ssize_t hnp_store(struct device *_dev,
-+ struct device_attribute *attr,
-+ const char *buf, size_t count)
-+{
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+ uint32_t in = simple_strtoul(buf, NULL, 16);
-+ dwc_otg_set_hnpreq(otg_dev->core_if, in);
-+ return count;
-+}
-+
-+DEVICE_ATTR(hnp, 0644, hnp_show, hnp_store);
-+
-+/**
-+ * @todo Add code to initiate the SRP.
-+ */
-+/**
-+ * Show the SRP status bit
-+ */
-+static ssize_t srp_show(struct device *_dev,
-+ struct device_attribute *attr, char *buf)
-+{
-+#ifndef DWC_HOST_ONLY
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+ return sprintf(buf, "SesReqScs = 0x%x\n",
-+ dwc_otg_get_srpstatus(otg_dev->core_if));
-+#else
-+ return sprintf(buf, "Host Only Mode!\n");
-+#endif
-+}
-+
-+/**
-+ * Set the SRP Request bit
-+ */
-+static ssize_t srp_store(struct device *_dev,
-+ struct device_attribute *attr,
-+ const char *buf, size_t count)
-+{
-+#ifndef DWC_HOST_ONLY
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+ dwc_otg_pcd_initiate_srp(otg_dev->pcd);
-+#endif
-+ return count;
-+}
-+
-+DEVICE_ATTR(srp, 0644, srp_show, srp_store);
-+
-+/**
-+ * @todo Need to do more for power on/off?
-+ */
-+/**
-+ * Show the Bus Power status
-+ */
-+static ssize_t buspower_show(struct device *_dev,
-+ struct device_attribute *attr, char *buf)
-+{
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+ return sprintf(buf, "Bus Power = 0x%x\n",
-+ dwc_otg_get_prtpower(otg_dev->core_if));
-+}
-+
-+/**
-+ * Set the Bus Power status
-+ */
-+static ssize_t buspower_store(struct device *_dev,
-+ struct device_attribute *attr,
-+ const char *buf, size_t count)
-+{
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+ uint32_t on = simple_strtoul(buf, NULL, 16);
-+ dwc_otg_set_prtpower(otg_dev->core_if, on);
-+ return count;
-+}
-+
-+DEVICE_ATTR(buspower, 0644, buspower_show, buspower_store);
-+
-+/**
-+ * @todo Need to do more for suspend?
-+ */
-+/**
-+ * Show the Bus Suspend status
-+ */
-+static ssize_t bussuspend_show(struct device *_dev,
-+ struct device_attribute *attr, char *buf)
-+{
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+ return sprintf(buf, "Bus Suspend = 0x%x\n",
-+ dwc_otg_get_prtsuspend(otg_dev->core_if));
-+}
-+
-+/**
-+ * Set the Bus Suspend status
-+ */
-+static ssize_t bussuspend_store(struct device *_dev,
-+ struct device_attribute *attr,
-+ const char *buf, size_t count)
-+{
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+ uint32_t in = simple_strtoul(buf, NULL, 16);
-+ dwc_otg_set_prtsuspend(otg_dev->core_if, in);
-+ return count;
-+}
-+
-+DEVICE_ATTR(bussuspend, 0644, bussuspend_show, bussuspend_store);
-+
-+/**
-+ * Show the Mode Change Ready Timer status
-+ */
-+static ssize_t mode_ch_tim_en_show(struct device *_dev,
-+ struct device_attribute *attr, char *buf)
-+{
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+ return sprintf(buf, "Mode Change Ready Timer Enable = 0x%x\n",
-+ dwc_otg_get_mode_ch_tim(otg_dev->core_if));
-+}
-+
-+/**
-+ * Set the Mode Change Ready Timer status
-+ */
-+static ssize_t mode_ch_tim_en_store(struct device *_dev,
-+ struct device_attribute *attr,
-+ const char *buf, size_t count)
-+{
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+ uint32_t in = simple_strtoul(buf, NULL, 16);
-+ dwc_otg_set_mode_ch_tim(otg_dev->core_if, in);
-+ return count;
-+}
-+
-+DEVICE_ATTR(mode_ch_tim_en, 0644, mode_ch_tim_en_show, mode_ch_tim_en_store);
-+
-+/**
-+ * Show the value of HFIR Frame Interval bitfield
-+ */
-+static ssize_t fr_interval_show(struct device *_dev,
-+ struct device_attribute *attr, char *buf)
-+{
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+ return sprintf(buf, "Frame Interval = 0x%x\n",
-+ dwc_otg_get_fr_interval(otg_dev->core_if));
-+}
-+
-+/**
-+ * Set the HFIR Frame Interval value
-+ */
-+static ssize_t fr_interval_store(struct device *_dev,
-+ struct device_attribute *attr,
-+ const char *buf, size_t count)
-+{
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+ uint32_t in = simple_strtoul(buf, NULL, 10);
-+ dwc_otg_set_fr_interval(otg_dev->core_if, in);
-+ return count;
-+}
-+
-+DEVICE_ATTR(fr_interval, 0644, fr_interval_show, fr_interval_store);
-+
-+/**
-+ * Show the status of Remote Wakeup.
-+ */
-+static ssize_t remote_wakeup_show(struct device *_dev,
-+ struct device_attribute *attr, char *buf)
-+{
-+#ifndef DWC_HOST_ONLY
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+
-+ return sprintf(buf,
-+ "Remote Wakeup Sig = %d Enabled = %d LPM Remote Wakeup = %d\n",
-+ dwc_otg_get_remotewakesig(otg_dev->core_if),
-+ dwc_otg_pcd_get_rmwkup_enable(otg_dev->pcd),
-+ dwc_otg_get_lpm_remotewakeenabled(otg_dev->core_if));
-+#else
-+ return sprintf(buf, "Host Only Mode!\n");
-+#endif /* DWC_HOST_ONLY */
-+}
-+
-+/**
-+ * Initiate a remote wakeup of the host. The Device control register
-+ * Remote Wakeup Signal bit is written if the PCD Remote wakeup enable
-+ * flag is set.
-+ *
-+ */
-+static ssize_t remote_wakeup_store(struct device *_dev,
-+ struct device_attribute *attr,
-+ const char *buf, size_t count)
-+{
-+#ifndef DWC_HOST_ONLY
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+ uint32_t val = simple_strtoul(buf, NULL, 16);
-+
-+ if (val & 1) {
-+ dwc_otg_pcd_remote_wakeup(otg_dev->pcd, 1);
-+ } else {
-+ dwc_otg_pcd_remote_wakeup(otg_dev->pcd, 0);
-+ }
-+#endif /* DWC_HOST_ONLY */
-+ return count;
-+}
-+
-+DEVICE_ATTR(remote_wakeup, S_IRUGO | S_IWUSR, remote_wakeup_show,
-+ remote_wakeup_store);
-+
-+/**
-+ * Show the whether core is hibernated or not.
-+ */
-+static ssize_t rem_wakeup_pwrdn_show(struct device *_dev,
-+ struct device_attribute *attr, char *buf)
-+{
-+#ifndef DWC_HOST_ONLY
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+
-+ if (dwc_otg_get_core_state(otg_dev->core_if)) {
-+ DWC_PRINTF("Core is in hibernation\n");
-+ } else {
-+ DWC_PRINTF("Core is not in hibernation\n");
-+ }
-+#endif /* DWC_HOST_ONLY */
-+ return 0;
-+}
-+
-+extern int dwc_otg_device_hibernation_restore(dwc_otg_core_if_t * core_if,
-+ int rem_wakeup, int reset);
-+
-+/**
-+ * Initiate a remote wakeup of the device to exit from hibernation.
-+ */
-+static ssize_t rem_wakeup_pwrdn_store(struct device *_dev,
-+ struct device_attribute *attr,
-+ const char *buf, size_t count)
-+{
-+#ifndef DWC_HOST_ONLY
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+ dwc_otg_device_hibernation_restore(otg_dev->core_if, 1, 0);
-+#endif
-+ return count;
-+}
-+
-+DEVICE_ATTR(rem_wakeup_pwrdn, S_IRUGO | S_IWUSR, rem_wakeup_pwrdn_show,
-+ rem_wakeup_pwrdn_store);
-+
-+static ssize_t disconnect_us(struct device *_dev,
-+ struct device_attribute *attr,
-+ const char *buf, size_t count)
-+{
-+
-+#ifndef DWC_HOST_ONLY
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+ uint32_t val = simple_strtoul(buf, NULL, 16);
-+ DWC_PRINTF("The Passed value is %04x\n", val);
-+
-+ dwc_otg_pcd_disconnect_us(otg_dev->pcd, 50);
-+
-+#endif /* DWC_HOST_ONLY */
-+ return count;
-+}
-+
-+DEVICE_ATTR(disconnect_us, S_IWUSR, 0, disconnect_us);
-+
-+/**
-+ * Dump global registers and either host or device registers (depending on the
-+ * current mode of the core).
-+ */
-+static ssize_t regdump_show(struct device *_dev,
-+ struct device_attribute *attr, char *buf)
-+{
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+
-+ dwc_otg_dump_global_registers(otg_dev->core_if);
-+ if (dwc_otg_is_host_mode(otg_dev->core_if)) {
-+ dwc_otg_dump_host_registers(otg_dev->core_if);
-+ } else {
-+ dwc_otg_dump_dev_registers(otg_dev->core_if);
-+
-+ }
-+ return sprintf(buf, "Register Dump\n");
-+}
-+
-+DEVICE_ATTR(regdump, S_IRUGO, regdump_show, 0);
-+
-+/**
-+ * Dump global registers and either host or device registers (depending on the
-+ * current mode of the core).
-+ */
-+static ssize_t spramdump_show(struct device *_dev,
-+ struct device_attribute *attr, char *buf)
-+{
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+
-+ //dwc_otg_dump_spram(otg_dev->core_if);
-+
-+ return sprintf(buf, "SPRAM Dump\n");
-+}
-+
-+DEVICE_ATTR(spramdump, S_IRUGO, spramdump_show, 0);
-+
-+/**
-+ * Dump the current hcd state.
-+ */
-+static ssize_t hcddump_show(struct device *_dev,
-+ struct device_attribute *attr, char *buf)
-+{
-+#ifndef DWC_DEVICE_ONLY
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+ dwc_otg_hcd_dump_state(otg_dev->hcd);
-+#endif /* DWC_DEVICE_ONLY */
-+ return sprintf(buf, "HCD Dump\n");
-+}
-+
-+DEVICE_ATTR(hcddump, S_IRUGO, hcddump_show, 0);
-+
-+/**
-+ * Dump the average frame remaining at SOF. This can be used to
-+ * determine average interrupt latency. Frame remaining is also shown for
-+ * start transfer and two additional sample points.
-+ */
-+static ssize_t hcd_frrem_show(struct device *_dev,
-+ struct device_attribute *attr, char *buf)
-+{
-+#ifndef DWC_DEVICE_ONLY
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+
-+ dwc_otg_hcd_dump_frrem(otg_dev->hcd);
-+#endif /* DWC_DEVICE_ONLY */
-+ return sprintf(buf, "HCD Dump Frame Remaining\n");
-+}
-+
-+DEVICE_ATTR(hcd_frrem, S_IRUGO, hcd_frrem_show, 0);
-+
-+/**
-+ * Displays the time required to read the GNPTXFSIZ register many times (the
-+ * output shows the number of times the register is read).
-+ */
-+#define RW_REG_COUNT 10000000
-+#define MSEC_PER_JIFFIE 1000/HZ
-+static ssize_t rd_reg_test_show(struct device *_dev,
-+ struct device_attribute *attr, char *buf)
-+{
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+ int i;
-+ int time;
-+ int start_jiffies;
-+
-+ printk("HZ %d, MSEC_PER_JIFFIE %d, loops_per_jiffy %lu\n",
-+ HZ, MSEC_PER_JIFFIE, loops_per_jiffy);
-+ start_jiffies = jiffies;
-+ for (i = 0; i < RW_REG_COUNT; i++) {
-+ dwc_otg_get_gnptxfsiz(otg_dev->core_if);
-+ }
-+ time = jiffies - start_jiffies;
-+ return sprintf(buf,
-+ "Time to read GNPTXFSIZ reg %d times: %d msecs (%d jiffies)\n",
-+ RW_REG_COUNT, time * MSEC_PER_JIFFIE, time);
-+}
-+
-+DEVICE_ATTR(rd_reg_test, S_IRUGO, rd_reg_test_show, 0);
-+
-+/**
-+ * Displays the time required to write the GNPTXFSIZ register many times (the
-+ * output shows the number of times the register is written).
-+ */
-+static ssize_t wr_reg_test_show(struct device *_dev,
-+ struct device_attribute *attr, char *buf)
-+{
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+ uint32_t reg_val;
-+ int i;
-+ int time;
-+ int start_jiffies;
-+
-+ printk("HZ %d, MSEC_PER_JIFFIE %d, loops_per_jiffy %lu\n",
-+ HZ, MSEC_PER_JIFFIE, loops_per_jiffy);
-+ reg_val = dwc_otg_get_gnptxfsiz(otg_dev->core_if);
-+ start_jiffies = jiffies;
-+ for (i = 0; i < RW_REG_COUNT; i++) {
-+ dwc_otg_set_gnptxfsiz(otg_dev->core_if, reg_val);
-+ }
-+ time = jiffies - start_jiffies;
-+ return sprintf(buf,
-+ "Time to write GNPTXFSIZ reg %d times: %d msecs (%d jiffies)\n",
-+ RW_REG_COUNT, time * MSEC_PER_JIFFIE, time);
-+}
-+
-+DEVICE_ATTR(wr_reg_test, S_IRUGO, wr_reg_test_show, 0);
-+
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+
-+/**
-+* Show the lpm_response attribute.
-+*/
-+static ssize_t lpmresp_show(struct device *_dev,
-+ struct device_attribute *attr, char *buf)
-+{
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+
-+ if (!dwc_otg_get_param_lpm_enable(otg_dev->core_if))
-+ return sprintf(buf, "** LPM is DISABLED **\n");
-+
-+ if (!dwc_otg_is_device_mode(otg_dev->core_if)) {
-+ return sprintf(buf, "** Current mode is not device mode\n");
-+ }
-+ return sprintf(buf, "lpm_response = %d\n",
-+ dwc_otg_get_lpmresponse(otg_dev->core_if));
-+}
-+
-+/**
-+* Store the lpm_response attribute.
-+*/
-+static ssize_t lpmresp_store(struct device *_dev,
-+ struct device_attribute *attr,
-+ const char *buf, size_t count)
-+{
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+ uint32_t val = simple_strtoul(buf, NULL, 16);
-+
-+ if (!dwc_otg_get_param_lpm_enable(otg_dev->core_if)) {
-+ return 0;
-+ }
-+
-+ if (!dwc_otg_is_device_mode(otg_dev->core_if)) {
-+ return 0;
-+ }
-+
-+ dwc_otg_set_lpmresponse(otg_dev->core_if, val);
-+ return count;
-+}
-+
-+DEVICE_ATTR(lpm_response, S_IRUGO | S_IWUSR, lpmresp_show, lpmresp_store);
-+
-+/**
-+* Show the sleep_status attribute.
-+*/
-+static ssize_t sleepstatus_show(struct device *_dev,
-+ struct device_attribute *attr, char *buf)
-+{
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+ return sprintf(buf, "Sleep Status = %d\n",
-+ dwc_otg_get_lpm_portsleepstatus(otg_dev->core_if));
-+}
-+
-+/**
-+ * Store the sleep_status attribure.
-+ */
-+static ssize_t sleepstatus_store(struct device *_dev,
-+ struct device_attribute *attr,
-+ const char *buf, size_t count)
-+{
-+ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev);
-+ dwc_otg_core_if_t *core_if = otg_dev->core_if;
-+
-+ if (dwc_otg_get_lpm_portsleepstatus(otg_dev->core_if)) {
-+ if (dwc_otg_is_host_mode(core_if)) {
-+
-+ DWC_PRINTF("Host initiated resume\n");
-+ dwc_otg_set_prtresume(otg_dev->core_if, 1);
-+ }
-+ }
-+
-+ return count;
-+}
-+
-+DEVICE_ATTR(sleep_status, S_IRUGO | S_IWUSR, sleepstatus_show,
-+ sleepstatus_store);
-+
-+#endif /* CONFIG_USB_DWC_OTG_LPM_ENABLE */
-+
-+/**@}*/
-+
-+/**
-+ * Create the device files
-+ */
-+void dwc_otg_attr_create(
-+#ifdef LM_INTERFACE
-+ struct lm_device *dev
-+#elif defined(PCI_INTERFACE)
-+ struct pci_dev *dev
-+#elif defined(PLATFORM_INTERFACE)
-+ struct platform_device *dev
-+#endif
-+ )
-+{
-+ int error;
-+
-+ error = device_create_file(&dev->dev, &dev_attr_regoffset);
-+ error = device_create_file(&dev->dev, &dev_attr_regvalue);
-+ error = device_create_file(&dev->dev, &dev_attr_mode);
-+ error = device_create_file(&dev->dev, &dev_attr_hnpcapable);
-+ error = device_create_file(&dev->dev, &dev_attr_srpcapable);
-+ error = device_create_file(&dev->dev, &dev_attr_hsic_connect);
-+ error = device_create_file(&dev->dev, &dev_attr_inv_sel_hsic);
-+ error = device_create_file(&dev->dev, &dev_attr_hnp);
-+ error = device_create_file(&dev->dev, &dev_attr_srp);
-+ error = device_create_file(&dev->dev, &dev_attr_buspower);
-+ error = device_create_file(&dev->dev, &dev_attr_bussuspend);
-+ error = device_create_file(&dev->dev, &dev_attr_mode_ch_tim_en);
-+ error = device_create_file(&dev->dev, &dev_attr_fr_interval);
-+ error = device_create_file(&dev->dev, &dev_attr_busconnected);
-+ error = device_create_file(&dev->dev, &dev_attr_gotgctl);
-+ error = device_create_file(&dev->dev, &dev_attr_gusbcfg);
-+ error = device_create_file(&dev->dev, &dev_attr_grxfsiz);
-+ error = device_create_file(&dev->dev, &dev_attr_gnptxfsiz);
-+ error = device_create_file(&dev->dev, &dev_attr_gpvndctl);
-+ error = device_create_file(&dev->dev, &dev_attr_ggpio);
-+ error = device_create_file(&dev->dev, &dev_attr_guid);
-+ error = device_create_file(&dev->dev, &dev_attr_gsnpsid);
-+ error = device_create_file(&dev->dev, &dev_attr_devspeed);
-+ error = device_create_file(&dev->dev, &dev_attr_enumspeed);
-+ error = device_create_file(&dev->dev, &dev_attr_hptxfsiz);
-+ error = device_create_file(&dev->dev, &dev_attr_hprt0);
-+ error = device_create_file(&dev->dev, &dev_attr_remote_wakeup);
-+ error = device_create_file(&dev->dev, &dev_attr_rem_wakeup_pwrdn);
-+ error = device_create_file(&dev->dev, &dev_attr_disconnect_us);
-+ error = device_create_file(&dev->dev, &dev_attr_regdump);
-+ error = device_create_file(&dev->dev, &dev_attr_spramdump);
-+ error = device_create_file(&dev->dev, &dev_attr_hcddump);
-+ error = device_create_file(&dev->dev, &dev_attr_hcd_frrem);
-+ error = device_create_file(&dev->dev, &dev_attr_rd_reg_test);
-+ error = device_create_file(&dev->dev, &dev_attr_wr_reg_test);
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+ error = device_create_file(&dev->dev, &dev_attr_lpm_response);
-+ error = device_create_file(&dev->dev, &dev_attr_sleep_status);
-+#endif
-+}
-+
-+/**
-+ * Remove the device files
-+ */
-+void dwc_otg_attr_remove(
-+#ifdef LM_INTERFACE
-+ struct lm_device *dev
-+#elif defined(PCI_INTERFACE)
-+ struct pci_dev *dev
-+#elif defined(PLATFORM_INTERFACE)
-+ struct platform_device *dev
-+#endif
-+ )
-+{
-+ device_remove_file(&dev->dev, &dev_attr_regoffset);
-+ device_remove_file(&dev->dev, &dev_attr_regvalue);
-+ device_remove_file(&dev->dev, &dev_attr_mode);
-+ device_remove_file(&dev->dev, &dev_attr_hnpcapable);
-+ device_remove_file(&dev->dev, &dev_attr_srpcapable);
-+ device_remove_file(&dev->dev, &dev_attr_hsic_connect);
-+ device_remove_file(&dev->dev, &dev_attr_inv_sel_hsic);
-+ device_remove_file(&dev->dev, &dev_attr_hnp);
-+ device_remove_file(&dev->dev, &dev_attr_srp);
-+ device_remove_file(&dev->dev, &dev_attr_buspower);
-+ device_remove_file(&dev->dev, &dev_attr_bussuspend);
-+ device_remove_file(&dev->dev, &dev_attr_mode_ch_tim_en);
-+ device_remove_file(&dev->dev, &dev_attr_fr_interval);
-+ device_remove_file(&dev->dev, &dev_attr_busconnected);
-+ device_remove_file(&dev->dev, &dev_attr_gotgctl);
-+ device_remove_file(&dev->dev, &dev_attr_gusbcfg);
-+ device_remove_file(&dev->dev, &dev_attr_grxfsiz);
-+ device_remove_file(&dev->dev, &dev_attr_gnptxfsiz);
-+ device_remove_file(&dev->dev, &dev_attr_gpvndctl);
-+ device_remove_file(&dev->dev, &dev_attr_ggpio);
-+ device_remove_file(&dev->dev, &dev_attr_guid);
-+ device_remove_file(&dev->dev, &dev_attr_gsnpsid);
-+ device_remove_file(&dev->dev, &dev_attr_devspeed);
-+ device_remove_file(&dev->dev, &dev_attr_enumspeed);
-+ device_remove_file(&dev->dev, &dev_attr_hptxfsiz);
-+ device_remove_file(&dev->dev, &dev_attr_hprt0);
-+ device_remove_file(&dev->dev, &dev_attr_remote_wakeup);
-+ device_remove_file(&dev->dev, &dev_attr_rem_wakeup_pwrdn);
-+ device_remove_file(&dev->dev, &dev_attr_disconnect_us);
-+ device_remove_file(&dev->dev, &dev_attr_regdump);
-+ device_remove_file(&dev->dev, &dev_attr_spramdump);
-+ device_remove_file(&dev->dev, &dev_attr_hcddump);
-+ device_remove_file(&dev->dev, &dev_attr_hcd_frrem);
-+ device_remove_file(&dev->dev, &dev_attr_rd_reg_test);
-+ device_remove_file(&dev->dev, &dev_attr_wr_reg_test);
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+ device_remove_file(&dev->dev, &dev_attr_lpm_response);
-+ device_remove_file(&dev->dev, &dev_attr_sleep_status);
-+#endif
-+}
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_attr.h
-@@ -0,0 +1,89 @@
-+/* ==========================================================================
-+ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_attr.h $
-+ * $Revision: #13 $
-+ * $Date: 2010/06/21 $
-+ * $Change: 1532021 $
-+ *
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+
-+#if !defined(__DWC_OTG_ATTR_H__)
-+#define __DWC_OTG_ATTR_H__
-+
-+/** @file
-+ * This file contains the interface to the Linux device attributes.
-+ */
-+extern struct device_attribute dev_attr_regoffset;
-+extern struct device_attribute dev_attr_regvalue;
-+
-+extern struct device_attribute dev_attr_mode;
-+extern struct device_attribute dev_attr_hnpcapable;
-+extern struct device_attribute dev_attr_srpcapable;
-+extern struct device_attribute dev_attr_hnp;
-+extern struct device_attribute dev_attr_srp;
-+extern struct device_attribute dev_attr_buspower;
-+extern struct device_attribute dev_attr_bussuspend;
-+extern struct device_attribute dev_attr_mode_ch_tim_en;
-+extern struct device_attribute dev_attr_fr_interval;
-+extern struct device_attribute dev_attr_busconnected;
-+extern struct device_attribute dev_attr_gotgctl;
-+extern struct device_attribute dev_attr_gusbcfg;
-+extern struct device_attribute dev_attr_grxfsiz;
-+extern struct device_attribute dev_attr_gnptxfsiz;
-+extern struct device_attribute dev_attr_gpvndctl;
-+extern struct device_attribute dev_attr_ggpio;
-+extern struct device_attribute dev_attr_guid;
-+extern struct device_attribute dev_attr_gsnpsid;
-+extern struct device_attribute dev_attr_devspeed;
-+extern struct device_attribute dev_attr_enumspeed;
-+extern struct device_attribute dev_attr_hptxfsiz;
-+extern struct device_attribute dev_attr_hprt0;
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+extern struct device_attribute dev_attr_lpm_response;
-+extern struct device_attribute devi_attr_sleep_status;
-+#endif
-+
-+void dwc_otg_attr_create(
-+#ifdef LM_INTERFACE
-+ struct lm_device *dev
-+#elif defined(PCI_INTERFACE)
-+ struct pci_dev *dev
-+#elif defined(PLATFORM_INTERFACE)
-+ struct platform_device *dev
-+#endif
-+ );
-+
-+void dwc_otg_attr_remove(
-+#ifdef LM_INTERFACE
-+ struct lm_device *dev
-+#elif defined(PCI_INTERFACE)
-+ struct pci_dev *dev
-+#elif defined(PLATFORM_INTERFACE)
-+ struct platform_device *dev
-+#endif
-+ );
-+#endif
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_cfi.c
-@@ -0,0 +1,1876 @@
-+/* ==========================================================================
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+
-+/** @file
-+ *
-+ * This file contains the most of the CFI(Core Feature Interface)
-+ * implementation for the OTG.
-+ */
-+
-+#ifdef DWC_UTE_CFI
-+
-+#include "dwc_otg_pcd.h"
-+#include "dwc_otg_cfi.h"
-+
-+/** This definition should actually migrate to the Portability Library */
-+#define DWC_CONSTANT_CPU_TO_LE16(x) (x)
-+
-+extern dwc_otg_pcd_ep_t *get_ep_by_addr(dwc_otg_pcd_t * pcd, u16 wIndex);
-+
-+static int cfi_core_features_buf(uint8_t * buf, uint16_t buflen);
-+static int cfi_get_feature_value(uint8_t * buf, uint16_t buflen,
-+ struct dwc_otg_pcd *pcd,
-+ struct cfi_usb_ctrlrequest *ctrl_req);
-+static int cfi_set_feature_value(struct dwc_otg_pcd *pcd);
-+static int cfi_ep_get_sg_val(uint8_t * buf, struct dwc_otg_pcd *pcd,
-+ struct cfi_usb_ctrlrequest *req);
-+static int cfi_ep_get_concat_val(uint8_t * buf, struct dwc_otg_pcd *pcd,
-+ struct cfi_usb_ctrlrequest *req);
-+static int cfi_ep_get_align_val(uint8_t * buf, struct dwc_otg_pcd *pcd,
-+ struct cfi_usb_ctrlrequest *req);
-+static int cfi_preproc_reset(struct dwc_otg_pcd *pcd,
-+ struct cfi_usb_ctrlrequest *req);
-+static void cfi_free_ep_bs_dyn_data(cfi_ep_t * cfiep);
-+
-+static uint16_t get_dfifo_size(dwc_otg_core_if_t * core_if);
-+static int32_t get_rxfifo_size(dwc_otg_core_if_t * core_if, uint16_t wValue);
-+static int32_t get_txfifo_size(struct dwc_otg_pcd *pcd, uint16_t wValue);
-+
-+static uint8_t resize_fifos(dwc_otg_core_if_t * core_if);
-+
-+/** This is the header of the all features descriptor */
-+static cfi_all_features_header_t all_props_desc_header = {
-+ .wVersion = DWC_CONSTANT_CPU_TO_LE16(0x100),
-+ .wCoreID = DWC_CONSTANT_CPU_TO_LE16(CFI_CORE_ID_OTG),
-+ .wNumFeatures = DWC_CONSTANT_CPU_TO_LE16(9),
-+};
-+
-+/** This is an array of statically allocated feature descriptors */
-+static cfi_feature_desc_header_t prop_descs[] = {
-+
-+ /* FT_ID_DMA_MODE */
-+ {
-+ .wFeatureID = DWC_CONSTANT_CPU_TO_LE16(FT_ID_DMA_MODE),
-+ .bmAttributes = CFI_FEATURE_ATTR_RW,
-+ .wDataLength = DWC_CONSTANT_CPU_TO_LE16(1),
-+ },
-+
-+ /* FT_ID_DMA_BUFFER_SETUP */
-+ {
-+ .wFeatureID = DWC_CONSTANT_CPU_TO_LE16(FT_ID_DMA_BUFFER_SETUP),
-+ .bmAttributes = CFI_FEATURE_ATTR_RW,
-+ .wDataLength = DWC_CONSTANT_CPU_TO_LE16(6),
-+ },
-+
-+ /* FT_ID_DMA_BUFF_ALIGN */
-+ {
-+ .wFeatureID = DWC_CONSTANT_CPU_TO_LE16(FT_ID_DMA_BUFF_ALIGN),
-+ .bmAttributes = CFI_FEATURE_ATTR_RW,
-+ .wDataLength = DWC_CONSTANT_CPU_TO_LE16(2),
-+ },
-+
-+ /* FT_ID_DMA_CONCAT_SETUP */
-+ {
-+ .wFeatureID = DWC_CONSTANT_CPU_TO_LE16(FT_ID_DMA_CONCAT_SETUP),
-+ .bmAttributes = CFI_FEATURE_ATTR_RW,
-+ //.wDataLength = DWC_CONSTANT_CPU_TO_LE16(6),
-+ },
-+
-+ /* FT_ID_DMA_CIRCULAR */
-+ {
-+ .wFeatureID = DWC_CONSTANT_CPU_TO_LE16(FT_ID_DMA_CIRCULAR),
-+ .bmAttributes = CFI_FEATURE_ATTR_RW,
-+ .wDataLength = DWC_CONSTANT_CPU_TO_LE16(6),
-+ },
-+
-+ /* FT_ID_THRESHOLD_SETUP */
-+ {
-+ .wFeatureID = DWC_CONSTANT_CPU_TO_LE16(FT_ID_THRESHOLD_SETUP),
-+ .bmAttributes = CFI_FEATURE_ATTR_RW,
-+ .wDataLength = DWC_CONSTANT_CPU_TO_LE16(6),
-+ },
-+
-+ /* FT_ID_DFIFO_DEPTH */
-+ {
-+ .wFeatureID = DWC_CONSTANT_CPU_TO_LE16(FT_ID_DFIFO_DEPTH),
-+ .bmAttributes = CFI_FEATURE_ATTR_RO,
-+ .wDataLength = DWC_CONSTANT_CPU_TO_LE16(2),
-+ },
-+
-+ /* FT_ID_TX_FIFO_DEPTH */
-+ {
-+ .wFeatureID = DWC_CONSTANT_CPU_TO_LE16(FT_ID_TX_FIFO_DEPTH),
-+ .bmAttributes = CFI_FEATURE_ATTR_RW,
-+ .wDataLength = DWC_CONSTANT_CPU_TO_LE16(2),
-+ },
-+
-+ /* FT_ID_RX_FIFO_DEPTH */
-+ {
-+ .wFeatureID = DWC_CONSTANT_CPU_TO_LE16(FT_ID_RX_FIFO_DEPTH),
-+ .bmAttributes = CFI_FEATURE_ATTR_RW,
-+ .wDataLength = DWC_CONSTANT_CPU_TO_LE16(2),
-+ }
-+};
-+
-+/** The table of feature names */
-+cfi_string_t prop_name_table[] = {
-+ {FT_ID_DMA_MODE, "dma_mode"},
-+ {FT_ID_DMA_BUFFER_SETUP, "buffer_setup"},
-+ {FT_ID_DMA_BUFF_ALIGN, "buffer_align"},
-+ {FT_ID_DMA_CONCAT_SETUP, "concat_setup"},
-+ {FT_ID_DMA_CIRCULAR, "buffer_circular"},
-+ {FT_ID_THRESHOLD_SETUP, "threshold_setup"},
-+ {FT_ID_DFIFO_DEPTH, "dfifo_depth"},
-+ {FT_ID_TX_FIFO_DEPTH, "txfifo_depth"},
-+ {FT_ID_RX_FIFO_DEPTH, "rxfifo_depth"},
-+ {}
-+};
-+
-+/************************************************************************/
-+
-+/**
-+ * Returns the name of the feature by its ID
-+ * or NULL if no featute ID matches.
-+ *
-+ */
-+const uint8_t *get_prop_name(uint16_t prop_id, int *len)
-+{
-+ cfi_string_t *pstr;
-+ *len = 0;
-+
-+ for (pstr = prop_name_table; pstr && pstr->s; pstr++) {
-+ if (pstr->id == prop_id) {
-+ *len = DWC_STRLEN(pstr->s);
-+ return pstr->s;
-+ }
-+ }
-+ return NULL;
-+}
-+
-+/**
-+ * This function handles all CFI specific control requests.
-+ *
-+ * Return a negative value to stall the DCE.
-+ */
-+int cfi_setup(struct dwc_otg_pcd *pcd, struct cfi_usb_ctrlrequest *ctrl)
-+{
-+ int retval = 0;
-+ dwc_otg_pcd_ep_t *ep = NULL;
-+ cfiobject_t *cfi = pcd->cfi;
-+ struct dwc_otg_core_if *coreif = GET_CORE_IF(pcd);
-+ uint16_t wLen = DWC_LE16_TO_CPU(&ctrl->wLength);
-+ uint16_t wValue = DWC_LE16_TO_CPU(&ctrl->wValue);
-+ uint16_t wIndex = DWC_LE16_TO_CPU(&ctrl->wIndex);
-+ uint32_t regaddr = 0;
-+ uint32_t regval = 0;
-+
-+ /* Save this Control Request in the CFI object.
-+ * The data field will be assigned in the data stage completion CB function.
-+ */
-+ cfi->ctrl_req = *ctrl;
-+ cfi->ctrl_req.data = NULL;
-+
-+ cfi->need_gadget_att = 0;
-+ cfi->need_status_in_complete = 0;
-+
-+ switch (ctrl->bRequest) {
-+ case VEN_CORE_GET_FEATURES:
-+ retval = cfi_core_features_buf(cfi->buf_in.buf, CFI_IN_BUF_LEN);
-+ if (retval >= 0) {
-+ //dump_msg(cfi->buf_in.buf, retval);
-+ ep = &pcd->ep0;
-+
-+ retval = min((uint16_t) retval, wLen);
-+ /* Transfer this buffer to the host through the EP0-IN EP */
-+ ep->dwc_ep.dma_addr = cfi->buf_in.addr;
-+ ep->dwc_ep.start_xfer_buff = cfi->buf_in.buf;
-+ ep->dwc_ep.xfer_buff = cfi->buf_in.buf;
-+ ep->dwc_ep.xfer_len = retval;
-+ ep->dwc_ep.xfer_count = 0;
-+ ep->dwc_ep.sent_zlp = 0;
-+ ep->dwc_ep.total_len = ep->dwc_ep.xfer_len;
-+
-+ pcd->ep0_pending = 1;
-+ dwc_otg_ep0_start_transfer(coreif, &ep->dwc_ep);
-+ }
-+ retval = 0;
-+ break;
-+
-+ case VEN_CORE_GET_FEATURE:
-+ CFI_INFO("VEN_CORE_GET_FEATURE\n");
-+ retval = cfi_get_feature_value(cfi->buf_in.buf, CFI_IN_BUF_LEN,
-+ pcd, ctrl);
-+ if (retval >= 0) {
-+ ep = &pcd->ep0;
-+
-+ retval = min((uint16_t) retval, wLen);
-+ /* Transfer this buffer to the host through the EP0-IN EP */
-+ ep->dwc_ep.dma_addr = cfi->buf_in.addr;
-+ ep->dwc_ep.start_xfer_buff = cfi->buf_in.buf;
-+ ep->dwc_ep.xfer_buff = cfi->buf_in.buf;
-+ ep->dwc_ep.xfer_len = retval;
-+ ep->dwc_ep.xfer_count = 0;
-+ ep->dwc_ep.sent_zlp = 0;
-+ ep->dwc_ep.total_len = ep->dwc_ep.xfer_len;
-+
-+ pcd->ep0_pending = 1;
-+ dwc_otg_ep0_start_transfer(coreif, &ep->dwc_ep);
-+ }
-+ CFI_INFO("VEN_CORE_GET_FEATURE=%d\n", retval);
-+ dump_msg(cfi->buf_in.buf, retval);
-+ break;
-+
-+ case VEN_CORE_SET_FEATURE:
-+ CFI_INFO("VEN_CORE_SET_FEATURE\n");
-+ /* Set up an XFER to get the data stage of the control request,
-+ * which is the new value of the feature to be modified.
-+ */
-+ ep = &pcd->ep0;
-+ ep->dwc_ep.is_in = 0;
-+ ep->dwc_ep.dma_addr = cfi->buf_out.addr;
-+ ep->dwc_ep.start_xfer_buff = cfi->buf_out.buf;
-+ ep->dwc_ep.xfer_buff = cfi->buf_out.buf;
-+ ep->dwc_ep.xfer_len = wLen;
-+ ep->dwc_ep.xfer_count = 0;
-+ ep->dwc_ep.sent_zlp = 0;
-+ ep->dwc_ep.total_len = ep->dwc_ep.xfer_len;
-+
-+ pcd->ep0_pending = 1;
-+ /* Read the control write's data stage */
-+ dwc_otg_ep0_start_transfer(coreif, &ep->dwc_ep);
-+ retval = 0;
-+ break;
-+
-+ case VEN_CORE_RESET_FEATURES:
-+ CFI_INFO("VEN_CORE_RESET_FEATURES\n");
-+ cfi->need_gadget_att = 1;
-+ cfi->need_status_in_complete = 1;
-+ retval = cfi_preproc_reset(pcd, ctrl);
-+ CFI_INFO("VEN_CORE_RESET_FEATURES = (%d)\n", retval);
-+ break;
-+
-+ case VEN_CORE_ACTIVATE_FEATURES:
-+ CFI_INFO("VEN_CORE_ACTIVATE_FEATURES\n");
-+ break;
-+
-+ case VEN_CORE_READ_REGISTER:
-+ CFI_INFO("VEN_CORE_READ_REGISTER\n");
-+ /* wValue optionally contains the HI WORD of the register offset and
-+ * wIndex contains the LOW WORD of the register offset
-+ */
-+ if (wValue == 0) {
-+ /* @TODO - MAS - fix the access to the base field */
-+ regaddr = 0;
-+ //regaddr = (uint32_t) pcd->otg_dev->os_dep.base;
-+ //GET_CORE_IF(pcd)->co
-+ regaddr |= wIndex;
-+ } else {
-+ regaddr = (wValue << 16) | wIndex;
-+ }
-+
-+ /* Read a 32-bit value of the memory at the regaddr */
-+ regval = DWC_READ_REG32((uint32_t *) regaddr);
-+
-+ ep = &pcd->ep0;
-+ dwc_memcpy(cfi->buf_in.buf, ®val, sizeof(uint32_t));
-+ ep->dwc_ep.is_in = 1;
-+ ep->dwc_ep.dma_addr = cfi->buf_in.addr;
-+ ep->dwc_ep.start_xfer_buff = cfi->buf_in.buf;
-+ ep->dwc_ep.xfer_buff = cfi->buf_in.buf;
-+ ep->dwc_ep.xfer_len = wLen;
-+ ep->dwc_ep.xfer_count = 0;
-+ ep->dwc_ep.sent_zlp = 0;
-+ ep->dwc_ep.total_len = ep->dwc_ep.xfer_len;
-+
-+ pcd->ep0_pending = 1;
-+ dwc_otg_ep0_start_transfer(coreif, &ep->dwc_ep);
-+ cfi->need_gadget_att = 0;
-+ retval = 0;
-+ break;
-+
-+ case VEN_CORE_WRITE_REGISTER:
-+ CFI_INFO("VEN_CORE_WRITE_REGISTER\n");
-+ /* Set up an XFER to get the data stage of the control request,
-+ * which is the new value of the register to be modified.
-+ */
-+ ep = &pcd->ep0;
-+ ep->dwc_ep.is_in = 0;
-+ ep->dwc_ep.dma_addr = cfi->buf_out.addr;
-+ ep->dwc_ep.start_xfer_buff = cfi->buf_out.buf;
-+ ep->dwc_ep.xfer_buff = cfi->buf_out.buf;
-+ ep->dwc_ep.xfer_len = wLen;
-+ ep->dwc_ep.xfer_count = 0;
-+ ep->dwc_ep.sent_zlp = 0;
-+ ep->dwc_ep.total_len = ep->dwc_ep.xfer_len;
-+
-+ pcd->ep0_pending = 1;
-+ /* Read the control write's data stage */
-+ dwc_otg_ep0_start_transfer(coreif, &ep->dwc_ep);
-+ retval = 0;
-+ break;
-+
-+ default:
-+ retval = -DWC_E_NOT_SUPPORTED;
-+ break;
-+ }
-+
-+ return retval;
-+}
-+
-+/**
-+ * This function prepares the core features descriptors and copies its
-+ * raw representation into the buffer <buf>.
-+ *
-+ * The buffer structure is as follows:
-+ * all_features_header (8 bytes)
-+ * features_#1 (8 bytes + feature name string length)
-+ * features_#2 (8 bytes + feature name string length)
-+ * .....
-+ * features_#n - where n=the total count of feature descriptors
-+ */
-+static int cfi_core_features_buf(uint8_t * buf, uint16_t buflen)
-+{
-+ cfi_feature_desc_header_t *prop_hdr = prop_descs;
-+ cfi_feature_desc_header_t *prop;
-+ cfi_all_features_header_t *all_props_hdr = &all_props_desc_header;
-+ cfi_all_features_header_t *tmp;
-+ uint8_t *tmpbuf = buf;
-+ const uint8_t *pname = NULL;
-+ int i, j, namelen = 0, totlen;
-+
-+ /* Prepare and copy the core features into the buffer */
-+ CFI_INFO("%s:\n", __func__);
-+
-+ tmp = (cfi_all_features_header_t *) tmpbuf;
-+ *tmp = *all_props_hdr;
-+ tmpbuf += CFI_ALL_FEATURES_HDR_LEN;
-+
-+ j = sizeof(prop_descs) / sizeof(cfi_all_features_header_t);
-+ for (i = 0; i < j; i++, prop_hdr++) {
-+ pname = get_prop_name(prop_hdr->wFeatureID, &namelen);
-+ prop = (cfi_feature_desc_header_t *) tmpbuf;
-+ *prop = *prop_hdr;
-+
-+ prop->bNameLen = namelen;
-+ prop->wLength =
-+ DWC_CONSTANT_CPU_TO_LE16(CFI_FEATURE_DESC_HDR_LEN +
-+ namelen);
-+
-+ tmpbuf += CFI_FEATURE_DESC_HDR_LEN;
-+ dwc_memcpy(tmpbuf, pname, namelen);
-+ tmpbuf += namelen;
-+ }
-+
-+ totlen = tmpbuf - buf;
-+
-+ if (totlen > 0) {
-+ tmp = (cfi_all_features_header_t *) buf;
-+ tmp->wTotalLen = DWC_CONSTANT_CPU_TO_LE16(totlen);
-+ }
-+
-+ return totlen;
-+}
-+
-+/**
-+ * This function releases all the dynamic memory in the CFI object.
-+ */
-+static void cfi_release(cfiobject_t * cfiobj)
-+{
-+ cfi_ep_t *cfiep;
-+ dwc_list_link_t *tmp;
-+
-+ CFI_INFO("%s\n", __func__);
-+
-+ if (cfiobj->buf_in.buf) {
-+ DWC_DMA_FREE(CFI_IN_BUF_LEN, cfiobj->buf_in.buf,
-+ cfiobj->buf_in.addr);
-+ cfiobj->buf_in.buf = NULL;
-+ }
-+
-+ if (cfiobj->buf_out.buf) {
-+ DWC_DMA_FREE(CFI_OUT_BUF_LEN, cfiobj->buf_out.buf,
-+ cfiobj->buf_out.addr);
-+ cfiobj->buf_out.buf = NULL;
-+ }
-+
-+ /* Free the Buffer Setup values for each EP */
-+ //list_for_each_entry(cfiep, &cfiobj->active_eps, lh) {
-+ DWC_LIST_FOREACH(tmp, &cfiobj->active_eps) {
-+ cfiep = DWC_LIST_ENTRY(tmp, struct cfi_ep, lh);
-+ cfi_free_ep_bs_dyn_data(cfiep);
-+ }
-+}
-+
-+/**
-+ * This function frees the dynamically allocated EP buffer setup data.
-+ */
-+static void cfi_free_ep_bs_dyn_data(cfi_ep_t * cfiep)
-+{
-+ if (cfiep->bm_sg) {
-+ DWC_FREE(cfiep->bm_sg);
-+ cfiep->bm_sg = NULL;
-+ }
-+
-+ if (cfiep->bm_align) {
-+ DWC_FREE(cfiep->bm_align);
-+ cfiep->bm_align = NULL;
-+ }
-+
-+ if (cfiep->bm_concat) {
-+ if (NULL != cfiep->bm_concat->wTxBytes) {
-+ DWC_FREE(cfiep->bm_concat->wTxBytes);
-+ cfiep->bm_concat->wTxBytes = NULL;
-+ }
-+ DWC_FREE(cfiep->bm_concat);
-+ cfiep->bm_concat = NULL;
-+ }
-+}
-+
-+/**
-+ * This function initializes the default values of the features
-+ * for a specific endpoint and should be called only once when
-+ * the EP is enabled first time.
-+ */
-+static int cfi_ep_init_defaults(struct dwc_otg_pcd *pcd, cfi_ep_t * cfiep)
-+{
-+ int retval = 0;
-+
-+ cfiep->bm_sg = DWC_ALLOC(sizeof(ddma_sg_buffer_setup_t));
-+ if (NULL == cfiep->bm_sg) {
-+ CFI_INFO("Failed to allocate memory for SG feature value\n");
-+ return -DWC_E_NO_MEMORY;
-+ }
-+ dwc_memset(cfiep->bm_sg, 0, sizeof(ddma_sg_buffer_setup_t));
-+
-+ /* For the Concatenation feature's default value we do not allocate
-+ * memory for the wTxBytes field - it will be done in the set_feature_value
-+ * request handler.
-+ */
-+ cfiep->bm_concat = DWC_ALLOC(sizeof(ddma_concat_buffer_setup_t));
-+ if (NULL == cfiep->bm_concat) {
-+ CFI_INFO
-+ ("Failed to allocate memory for CONCATENATION feature value\n");
-+ DWC_FREE(cfiep->bm_sg);
-+ return -DWC_E_NO_MEMORY;
-+ }
-+ dwc_memset(cfiep->bm_concat, 0, sizeof(ddma_concat_buffer_setup_t));
-+
-+ cfiep->bm_align = DWC_ALLOC(sizeof(ddma_align_buffer_setup_t));
-+ if (NULL == cfiep->bm_align) {
-+ CFI_INFO
-+ ("Failed to allocate memory for Alignment feature value\n");
-+ DWC_FREE(cfiep->bm_sg);
-+ DWC_FREE(cfiep->bm_concat);
-+ return -DWC_E_NO_MEMORY;
-+ }
-+ dwc_memset(cfiep->bm_align, 0, sizeof(ddma_align_buffer_setup_t));
-+
-+ return retval;
-+}
-+
-+/**
-+ * The callback function that notifies the CFI on the activation of
-+ * an endpoint in the PCD. The following steps are done in this function:
-+ *
-+ * Create a dynamically allocated cfi_ep_t object (a CFI wrapper to the PCD's
-+ * active endpoint)
-+ * Create MAX_DMA_DESCS_PER_EP count DMA Descriptors for the EP
-+ * Set the Buffer Mode to standard
-+ * Initialize the default values for all EP modes (SG, Circular, Concat, Align)
-+ * Add the cfi_ep_t object to the list of active endpoints in the CFI object
-+ */
-+static int cfi_ep_enable(struct cfiobject *cfi, struct dwc_otg_pcd *pcd,
-+ struct dwc_otg_pcd_ep *ep)
-+{
-+ cfi_ep_t *cfiep;
-+ int retval = -DWC_E_NOT_SUPPORTED;
-+
-+ CFI_INFO("%s: epname=%s; epnum=0x%02x\n", __func__,
-+ "EP_" /*ep->ep.name */ , ep->desc->bEndpointAddress);
-+ /* MAS - Check whether this endpoint already is in the list */
-+ cfiep = get_cfi_ep_by_pcd_ep(cfi, ep);
-+
-+ if (NULL == cfiep) {
-+ /* Allocate a cfi_ep_t object */
-+ cfiep = DWC_ALLOC(sizeof(cfi_ep_t));
-+ if (NULL == cfiep) {
-+ CFI_INFO
-+ ("Unable to allocate memory for <cfiep> in function %s\n",
-+ __func__);
-+ return -DWC_E_NO_MEMORY;
-+ }
-+ dwc_memset(cfiep, 0, sizeof(cfi_ep_t));
-+
-+ /* Save the dwc_otg_pcd_ep pointer in the cfiep object */
-+ cfiep->ep = ep;
-+
-+ /* Allocate the DMA Descriptors chain of MAX_DMA_DESCS_PER_EP count */
-+ ep->dwc_ep.descs =
-+ DWC_DMA_ALLOC(MAX_DMA_DESCS_PER_EP *
-+ sizeof(dwc_otg_dma_desc_t),
-+ &ep->dwc_ep.descs_dma_addr);
-+
-+ if (NULL == ep->dwc_ep.descs) {
-+ DWC_FREE(cfiep);
-+ return -DWC_E_NO_MEMORY;
-+ }
-+
-+ DWC_LIST_INIT(&cfiep->lh);
-+
-+ /* Set the buffer mode to BM_STANDARD. It will be modified
-+ * when building descriptors for a specific buffer mode */
-+ ep->dwc_ep.buff_mode = BM_STANDARD;
-+
-+ /* Create and initialize the default values for this EP's Buffer modes */
-+ if ((retval = cfi_ep_init_defaults(pcd, cfiep)) < 0)
-+ return retval;
-+
-+ /* Add the cfi_ep_t object to the CFI object's list of active endpoints */
-+ DWC_LIST_INSERT_TAIL(&cfi->active_eps, &cfiep->lh);
-+ retval = 0;
-+ } else { /* The sought EP already is in the list */
-+ CFI_INFO("%s: The sought EP already is in the list\n",
-+ __func__);
-+ }
-+
-+ return retval;
-+}
-+
-+/**
-+ * This function is called when the data stage of a 3-stage Control Write request
-+ * is complete.
-+ *
-+ */
-+static int cfi_ctrl_write_complete(struct cfiobject *cfi,
-+ struct dwc_otg_pcd *pcd)
-+{
-+ uint32_t addr, reg_value;
-+ uint16_t wIndex, wValue;
-+ uint8_t bRequest;
-+ uint8_t *buf = cfi->buf_out.buf;
-+ //struct usb_ctrlrequest *ctrl_req = &cfi->ctrl_req_saved;
-+ struct cfi_usb_ctrlrequest *ctrl_req = &cfi->ctrl_req;
-+ int retval = -DWC_E_NOT_SUPPORTED;
-+
-+ CFI_INFO("%s\n", __func__);
-+
-+ bRequest = ctrl_req->bRequest;
-+ wIndex = DWC_CONSTANT_CPU_TO_LE16(ctrl_req->wIndex);
-+ wValue = DWC_CONSTANT_CPU_TO_LE16(ctrl_req->wValue);
-+
-+ /*
-+ * Save the pointer to the data stage in the ctrl_req's <data> field.
-+ * The request should be already saved in the command stage by now.
-+ */
-+ ctrl_req->data = cfi->buf_out.buf;
-+ cfi->need_status_in_complete = 0;
-+ cfi->need_gadget_att = 0;
-+
-+ switch (bRequest) {
-+ case VEN_CORE_WRITE_REGISTER:
-+ /* The buffer contains raw data of the new value for the register */
-+ reg_value = *((uint32_t *) buf);
-+ if (wValue == 0) {
-+ addr = 0;
-+ //addr = (uint32_t) pcd->otg_dev->os_dep.base;
-+ addr += wIndex;
-+ } else {
-+ addr = (wValue << 16) | wIndex;
-+ }
-+
-+ //writel(reg_value, addr);
-+
-+ retval = 0;
-+ cfi->need_status_in_complete = 1;
-+ break;
-+
-+ case VEN_CORE_SET_FEATURE:
-+ /* The buffer contains raw data of the new value of the feature */
-+ retval = cfi_set_feature_value(pcd);
-+ if (retval < 0)
-+ return retval;
-+
-+ cfi->need_status_in_complete = 1;
-+ break;
-+
-+ default:
-+ break;
-+ }
-+
-+ return retval;
-+}
-+
-+/**
-+ * This function builds the DMA descriptors for the SG buffer mode.
-+ */
-+static void cfi_build_sg_descs(struct cfiobject *cfi, cfi_ep_t * cfiep,
-+ dwc_otg_pcd_request_t * req)
-+{
-+ struct dwc_otg_pcd_ep *ep = cfiep->ep;
-+ ddma_sg_buffer_setup_t *sgval = cfiep->bm_sg;
-+ struct dwc_otg_dma_desc *desc = cfiep->ep->dwc_ep.descs;
-+ struct dwc_otg_dma_desc *desc_last = cfiep->ep->dwc_ep.descs;
-+ dma_addr_t buff_addr = req->dma;
-+ int i;
-+ uint32_t txsize, off;
-+
-+ txsize = sgval->wSize;
-+ off = sgval->bOffset;
-+
-+// CFI_INFO("%s: %s TXSIZE=0x%08x; OFFSET=0x%08x\n",
-+// __func__, cfiep->ep->ep.name, txsize, off);
-+
-+ for (i = 0; i < sgval->bCount; i++) {
-+ desc->status.b.bs = BS_HOST_BUSY;
-+ desc->buf = buff_addr;
-+ desc->status.b.l = 0;
-+ desc->status.b.ioc = 0;
-+ desc->status.b.sp = 0;
-+ desc->status.b.bytes = txsize;
-+ desc->status.b.bs = BS_HOST_READY;
-+
-+ /* Set the next address of the buffer */
-+ buff_addr += txsize + off;
-+ desc_last = desc;
-+ desc++;
-+ }
-+
-+ /* Set the last, ioc and sp bits on the Last DMA Descriptor */
-+ desc_last->status.b.l = 1;
-+ desc_last->status.b.ioc = 1;
-+ desc_last->status.b.sp = ep->dwc_ep.sent_zlp;
-+ /* Save the last DMA descriptor pointer */
-+ cfiep->dma_desc_last = desc_last;
-+ cfiep->desc_count = sgval->bCount;
-+}
-+
-+/**
-+ * This function builds the DMA descriptors for the Concatenation buffer mode.
-+ */
-+static void cfi_build_concat_descs(struct cfiobject *cfi, cfi_ep_t * cfiep,
-+ dwc_otg_pcd_request_t * req)
-+{
-+ struct dwc_otg_pcd_ep *ep = cfiep->ep;
-+ ddma_concat_buffer_setup_t *concatval = cfiep->bm_concat;
-+ struct dwc_otg_dma_desc *desc = cfiep->ep->dwc_ep.descs;
-+ struct dwc_otg_dma_desc *desc_last = cfiep->ep->dwc_ep.descs;
-+ dma_addr_t buff_addr = req->dma;
-+ int i;
-+ uint16_t *txsize;
-+
-+ txsize = concatval->wTxBytes;
-+
-+ for (i = 0; i < concatval->hdr.bDescCount; i++) {
-+ desc->buf = buff_addr;
-+ desc->status.b.bs = BS_HOST_BUSY;
-+ desc->status.b.l = 0;
-+ desc->status.b.ioc = 0;
-+ desc->status.b.sp = 0;
-+ desc->status.b.bytes = *txsize;
-+ desc->status.b.bs = BS_HOST_READY;
-+
-+ txsize++;
-+ /* Set the next address of the buffer */
-+ buff_addr += UGETW(ep->desc->wMaxPacketSize);
-+ desc_last = desc;
-+ desc++;
-+ }
-+
-+ /* Set the last, ioc and sp bits on the Last DMA Descriptor */
-+ desc_last->status.b.l = 1;
-+ desc_last->status.b.ioc = 1;
-+ desc_last->status.b.sp = ep->dwc_ep.sent_zlp;
-+ cfiep->dma_desc_last = desc_last;
-+ cfiep->desc_count = concatval->hdr.bDescCount;
-+}
-+
-+/**
-+ * This function builds the DMA descriptors for the Circular buffer mode
-+ */
-+static void cfi_build_circ_descs(struct cfiobject *cfi, cfi_ep_t * cfiep,
-+ dwc_otg_pcd_request_t * req)
-+{
-+ /* @todo: MAS - add implementation when this feature needs to be tested */
-+}
-+
-+/**
-+ * This function builds the DMA descriptors for the Alignment buffer mode
-+ */
-+static void cfi_build_align_descs(struct cfiobject *cfi, cfi_ep_t * cfiep,
-+ dwc_otg_pcd_request_t * req)
-+{
-+ struct dwc_otg_pcd_ep *ep = cfiep->ep;
-+ ddma_align_buffer_setup_t *alignval = cfiep->bm_align;
-+ struct dwc_otg_dma_desc *desc = cfiep->ep->dwc_ep.descs;
-+ dma_addr_t buff_addr = req->dma;
-+
-+ desc->status.b.bs = BS_HOST_BUSY;
-+ desc->status.b.l = 1;
-+ desc->status.b.ioc = 1;
-+ desc->status.b.sp = ep->dwc_ep.sent_zlp;
-+ desc->status.b.bytes = req->length;
-+ /* Adjust the buffer alignment */
-+ desc->buf = (buff_addr + alignval->bAlign);
-+ desc->status.b.bs = BS_HOST_READY;
-+ cfiep->dma_desc_last = desc;
-+ cfiep->desc_count = 1;
-+}
-+
-+/**
-+ * This function builds the DMA descriptors chain for different modes of the
-+ * buffer setup of an endpoint.
-+ */
-+static void cfi_build_descriptors(struct cfiobject *cfi,
-+ struct dwc_otg_pcd *pcd,
-+ struct dwc_otg_pcd_ep *ep,
-+ dwc_otg_pcd_request_t * req)
-+{
-+ cfi_ep_t *cfiep;
-+
-+ /* Get the cfiep by the dwc_otg_pcd_ep */
-+ cfiep = get_cfi_ep_by_pcd_ep(cfi, ep);
-+ if (NULL == cfiep) {
-+ CFI_INFO("%s: Unable to find a matching active endpoint\n",
-+ __func__);
-+ return;
-+ }
-+
-+ cfiep->xfer_len = req->length;
-+
-+ /* Iterate through all the DMA descriptors */
-+ switch (cfiep->ep->dwc_ep.buff_mode) {
-+ case BM_SG:
-+ cfi_build_sg_descs(cfi, cfiep, req);
-+ break;
-+
-+ case BM_CONCAT:
-+ cfi_build_concat_descs(cfi, cfiep, req);
-+ break;
-+
-+ case BM_CIRCULAR:
-+ cfi_build_circ_descs(cfi, cfiep, req);
-+ break;
-+
-+ case BM_ALIGN:
-+ cfi_build_align_descs(cfi, cfiep, req);
-+ break;
-+
-+ default:
-+ break;
-+ }
-+}
-+
-+/**
-+ * Allocate DMA buffer for different Buffer modes.
-+ */
-+static void *cfi_ep_alloc_buf(struct cfiobject *cfi, struct dwc_otg_pcd *pcd,
-+ struct dwc_otg_pcd_ep *ep, dma_addr_t * dma,
-+ unsigned size, gfp_t flags)
-+{
-+ return DWC_DMA_ALLOC(size, dma);
-+}
-+
-+/**
-+ * This function initializes the CFI object.
-+ */
-+int init_cfi(cfiobject_t * cfiobj)
-+{
-+ CFI_INFO("%s\n", __func__);
-+
-+ /* Allocate a buffer for IN XFERs */
-+ cfiobj->buf_in.buf =
-+ DWC_DMA_ALLOC(CFI_IN_BUF_LEN, &cfiobj->buf_in.addr);
-+ if (NULL == cfiobj->buf_in.buf) {
-+ CFI_INFO("Unable to allocate buffer for INs\n");
-+ return -DWC_E_NO_MEMORY;
-+ }
-+
-+ /* Allocate a buffer for OUT XFERs */
-+ cfiobj->buf_out.buf =
-+ DWC_DMA_ALLOC(CFI_OUT_BUF_LEN, &cfiobj->buf_out.addr);
-+ if (NULL == cfiobj->buf_out.buf) {
-+ CFI_INFO("Unable to allocate buffer for OUT\n");
-+ return -DWC_E_NO_MEMORY;
-+ }
-+
-+ /* Initialize the callback function pointers */
-+ cfiobj->ops.release = cfi_release;
-+ cfiobj->ops.ep_enable = cfi_ep_enable;
-+ cfiobj->ops.ctrl_write_complete = cfi_ctrl_write_complete;
-+ cfiobj->ops.build_descriptors = cfi_build_descriptors;
-+ cfiobj->ops.ep_alloc_buf = cfi_ep_alloc_buf;
-+
-+ /* Initialize the list of active endpoints in the CFI object */
-+ DWC_LIST_INIT(&cfiobj->active_eps);
-+
-+ return 0;
-+}
-+
-+/**
-+ * This function reads the required feature's current value into the buffer
-+ *
-+ * @retval: Returns negative as error, or the data length of the feature
-+ */
-+static int cfi_get_feature_value(uint8_t * buf, uint16_t buflen,
-+ struct dwc_otg_pcd *pcd,
-+ struct cfi_usb_ctrlrequest *ctrl_req)
-+{
-+ int retval = -DWC_E_NOT_SUPPORTED;
-+ struct dwc_otg_core_if *coreif = GET_CORE_IF(pcd);
-+ uint16_t dfifo, rxfifo, txfifo;
-+
-+ switch (ctrl_req->wIndex) {
-+ /* Whether the DDMA is enabled or not */
-+ case FT_ID_DMA_MODE:
-+ *buf = (coreif->dma_enable && coreif->dma_desc_enable) ? 1 : 0;
-+ retval = 1;
-+ break;
-+
-+ case FT_ID_DMA_BUFFER_SETUP:
-+ retval = cfi_ep_get_sg_val(buf, pcd, ctrl_req);
-+ break;
-+
-+ case FT_ID_DMA_BUFF_ALIGN:
-+ retval = cfi_ep_get_align_val(buf, pcd, ctrl_req);
-+ break;
-+
-+ case FT_ID_DMA_CONCAT_SETUP:
-+ retval = cfi_ep_get_concat_val(buf, pcd, ctrl_req);
-+ break;
-+
-+ case FT_ID_DMA_CIRCULAR:
-+ CFI_INFO("GetFeature value (FT_ID_DMA_CIRCULAR)\n");
-+ break;
-+
-+ case FT_ID_THRESHOLD_SETUP:
-+ CFI_INFO("GetFeature value (FT_ID_THRESHOLD_SETUP)\n");
-+ break;
-+
-+ case FT_ID_DFIFO_DEPTH:
-+ dfifo = get_dfifo_size(coreif);
-+ *((uint16_t *) buf) = dfifo;
-+ retval = sizeof(uint16_t);
-+ break;
-+
-+ case FT_ID_TX_FIFO_DEPTH:
-+ retval = get_txfifo_size(pcd, ctrl_req->wValue);
-+ if (retval >= 0) {
-+ txfifo = retval;
-+ *((uint16_t *) buf) = txfifo;
-+ retval = sizeof(uint16_t);
-+ }
-+ break;
-+
-+ case FT_ID_RX_FIFO_DEPTH:
-+ retval = get_rxfifo_size(coreif, ctrl_req->wValue);
-+ if (retval >= 0) {
-+ rxfifo = retval;
-+ *((uint16_t *) buf) = rxfifo;
-+ retval = sizeof(uint16_t);
-+ }
-+ break;
-+ }
-+
-+ return retval;
-+}
-+
-+/**
-+ * This function resets the SG for the specified EP to its default value
-+ */
-+static int cfi_reset_sg_val(cfi_ep_t * cfiep)
-+{
-+ dwc_memset(cfiep->bm_sg, 0, sizeof(ddma_sg_buffer_setup_t));
-+ return 0;
-+}
-+
-+/**
-+ * This function resets the Alignment for the specified EP to its default value
-+ */
-+static int cfi_reset_align_val(cfi_ep_t * cfiep)
-+{
-+ dwc_memset(cfiep->bm_sg, 0, sizeof(ddma_sg_buffer_setup_t));
-+ return 0;
-+}
-+
-+/**
-+ * This function resets the Concatenation for the specified EP to its default value
-+ * This function will also set the value of the wTxBytes field to NULL after
-+ * freeing the memory previously allocated for this field.
-+ */
-+static int cfi_reset_concat_val(cfi_ep_t * cfiep)
-+{
-+ /* First we need to free the wTxBytes field */
-+ if (cfiep->bm_concat->wTxBytes) {
-+ DWC_FREE(cfiep->bm_concat->wTxBytes);
-+ cfiep->bm_concat->wTxBytes = NULL;
-+ }
-+
-+ dwc_memset(cfiep->bm_concat, 0, sizeof(ddma_concat_buffer_setup_t));
-+ return 0;
-+}
-+
-+/**
-+ * This function resets all the buffer setups of the specified endpoint
-+ */
-+static int cfi_ep_reset_all_setup_vals(cfi_ep_t * cfiep)
-+{
-+ cfi_reset_sg_val(cfiep);
-+ cfi_reset_align_val(cfiep);
-+ cfi_reset_concat_val(cfiep);
-+ return 0;
-+}
-+
-+static int cfi_handle_reset_fifo_val(struct dwc_otg_pcd *pcd, uint8_t ep_addr,
-+ uint8_t rx_rst, uint8_t tx_rst)
-+{
-+ int retval = -DWC_E_INVALID;
-+ uint16_t tx_siz[15];
-+ uint16_t rx_siz = 0;
-+ dwc_otg_pcd_ep_t *ep = NULL;
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+ dwc_otg_core_params_t *params = GET_CORE_IF(pcd)->core_params;
-+
-+ if (rx_rst) {
-+ rx_siz = params->dev_rx_fifo_size;
-+ params->dev_rx_fifo_size = GET_CORE_IF(pcd)->init_rxfsiz;
-+ }
-+
-+ if (tx_rst) {
-+ if (ep_addr == 0) {
-+ int i;
-+
-+ for (i = 0; i < core_if->hwcfg4.b.num_in_eps; i++) {
-+ tx_siz[i] =
-+ core_if->core_params->dev_tx_fifo_size[i];
-+ core_if->core_params->dev_tx_fifo_size[i] =
-+ core_if->init_txfsiz[i];
-+ }
-+ } else {
-+
-+ ep = get_ep_by_addr(pcd, ep_addr);
-+
-+ if (NULL == ep) {
-+ CFI_INFO
-+ ("%s: Unable to get the endpoint addr=0x%02x\n",
-+ __func__, ep_addr);
-+ return -DWC_E_INVALID;
-+ }
-+
-+ tx_siz[0] =
-+ params->dev_tx_fifo_size[ep->dwc_ep.tx_fifo_num -
-+ 1];
-+ params->dev_tx_fifo_size[ep->dwc_ep.tx_fifo_num - 1] =
-+ GET_CORE_IF(pcd)->init_txfsiz[ep->
-+ dwc_ep.tx_fifo_num -
-+ 1];
-+ }
-+ }
-+
-+ if (resize_fifos(GET_CORE_IF(pcd))) {
-+ retval = 0;
-+ } else {
-+ CFI_INFO
-+ ("%s: Error resetting the feature Reset All(FIFO size)\n",
-+ __func__);
-+ if (rx_rst) {
-+ params->dev_rx_fifo_size = rx_siz;
-+ }
-+
-+ if (tx_rst) {
-+ if (ep_addr == 0) {
-+ int i;
-+ for (i = 0; i < core_if->hwcfg4.b.num_in_eps;
-+ i++) {
-+ core_if->
-+ core_params->dev_tx_fifo_size[i] =
-+ tx_siz[i];
-+ }
-+ } else {
-+ params->dev_tx_fifo_size[ep->
-+ dwc_ep.tx_fifo_num -
-+ 1] = tx_siz[0];
-+ }
-+ }
-+ retval = -DWC_E_INVALID;
-+ }
-+ return retval;
-+}
-+
-+static int cfi_handle_reset_all(struct dwc_otg_pcd *pcd, uint8_t addr)
-+{
-+ int retval = 0;
-+ cfi_ep_t *cfiep;
-+ cfiobject_t *cfi = pcd->cfi;
-+ dwc_list_link_t *tmp;
-+
-+ retval = cfi_handle_reset_fifo_val(pcd, addr, 1, 1);
-+ if (retval < 0) {
-+ return retval;
-+ }
-+
-+ /* If the EP address is known then reset the features for only that EP */
-+ if (addr) {
-+ cfiep = get_cfi_ep_by_addr(pcd->cfi, addr);
-+ if (NULL == cfiep) {
-+ CFI_INFO("%s: Error getting the EP address 0x%02x\n",
-+ __func__, addr);
-+ return -DWC_E_INVALID;
-+ }
-+ retval = cfi_ep_reset_all_setup_vals(cfiep);
-+ cfiep->ep->dwc_ep.buff_mode = BM_STANDARD;
-+ }
-+ /* Otherwise (wValue == 0), reset all features of all EP's */
-+ else {
-+ /* Traverse all the active EP's and reset the feature(s) value(s) */
-+ //list_for_each_entry(cfiep, &cfi->active_eps, lh) {
-+ DWC_LIST_FOREACH(tmp, &cfi->active_eps) {
-+ cfiep = DWC_LIST_ENTRY(tmp, struct cfi_ep, lh);
-+ retval = cfi_ep_reset_all_setup_vals(cfiep);
-+ cfiep->ep->dwc_ep.buff_mode = BM_STANDARD;
-+ if (retval < 0) {
-+ CFI_INFO
-+ ("%s: Error resetting the feature Reset All\n",
-+ __func__);
-+ return retval;
-+ }
-+ }
-+ }
-+ return retval;
-+}
-+
-+static int cfi_handle_reset_dma_buff_setup(struct dwc_otg_pcd *pcd,
-+ uint8_t addr)
-+{
-+ int retval = 0;
-+ cfi_ep_t *cfiep;
-+ cfiobject_t *cfi = pcd->cfi;
-+ dwc_list_link_t *tmp;
-+
-+ /* If the EP address is known then reset the features for only that EP */
-+ if (addr) {
-+ cfiep = get_cfi_ep_by_addr(pcd->cfi, addr);
-+ if (NULL == cfiep) {
-+ CFI_INFO("%s: Error getting the EP address 0x%02x\n",
-+ __func__, addr);
-+ return -DWC_E_INVALID;
-+ }
-+ retval = cfi_reset_sg_val(cfiep);
-+ }
-+ /* Otherwise (wValue == 0), reset all features of all EP's */
-+ else {
-+ /* Traverse all the active EP's and reset the feature(s) value(s) */
-+ //list_for_each_entry(cfiep, &cfi->active_eps, lh) {
-+ DWC_LIST_FOREACH(tmp, &cfi->active_eps) {
-+ cfiep = DWC_LIST_ENTRY(tmp, struct cfi_ep, lh);
-+ retval = cfi_reset_sg_val(cfiep);
-+ if (retval < 0) {
-+ CFI_INFO
-+ ("%s: Error resetting the feature Buffer Setup\n",
-+ __func__);
-+ return retval;
-+ }
-+ }
-+ }
-+ return retval;
-+}
-+
-+static int cfi_handle_reset_concat_val(struct dwc_otg_pcd *pcd, uint8_t addr)
-+{
-+ int retval = 0;
-+ cfi_ep_t *cfiep;
-+ cfiobject_t *cfi = pcd->cfi;
-+ dwc_list_link_t *tmp;
-+
-+ /* If the EP address is known then reset the features for only that EP */
-+ if (addr) {
-+ cfiep = get_cfi_ep_by_addr(pcd->cfi, addr);
-+ if (NULL == cfiep) {
-+ CFI_INFO("%s: Error getting the EP address 0x%02x\n",
-+ __func__, addr);
-+ return -DWC_E_INVALID;
-+ }
-+ retval = cfi_reset_concat_val(cfiep);
-+ }
-+ /* Otherwise (wValue == 0), reset all features of all EP's */
-+ else {
-+ /* Traverse all the active EP's and reset the feature(s) value(s) */
-+ //list_for_each_entry(cfiep, &cfi->active_eps, lh) {
-+ DWC_LIST_FOREACH(tmp, &cfi->active_eps) {
-+ cfiep = DWC_LIST_ENTRY(tmp, struct cfi_ep, lh);
-+ retval = cfi_reset_concat_val(cfiep);
-+ if (retval < 0) {
-+ CFI_INFO
-+ ("%s: Error resetting the feature Concatenation Value\n",
-+ __func__);
-+ return retval;
-+ }
-+ }
-+ }
-+ return retval;
-+}
-+
-+static int cfi_handle_reset_align_val(struct dwc_otg_pcd *pcd, uint8_t addr)
-+{
-+ int retval = 0;
-+ cfi_ep_t *cfiep;
-+ cfiobject_t *cfi = pcd->cfi;
-+ dwc_list_link_t *tmp;
-+
-+ /* If the EP address is known then reset the features for only that EP */
-+ if (addr) {
-+ cfiep = get_cfi_ep_by_addr(pcd->cfi, addr);
-+ if (NULL == cfiep) {
-+ CFI_INFO("%s: Error getting the EP address 0x%02x\n",
-+ __func__, addr);
-+ return -DWC_E_INVALID;
-+ }
-+ retval = cfi_reset_align_val(cfiep);
-+ }
-+ /* Otherwise (wValue == 0), reset all features of all EP's */
-+ else {
-+ /* Traverse all the active EP's and reset the feature(s) value(s) */
-+ //list_for_each_entry(cfiep, &cfi->active_eps, lh) {
-+ DWC_LIST_FOREACH(tmp, &cfi->active_eps) {
-+ cfiep = DWC_LIST_ENTRY(tmp, struct cfi_ep, lh);
-+ retval = cfi_reset_align_val(cfiep);
-+ if (retval < 0) {
-+ CFI_INFO
-+ ("%s: Error resetting the feature Aliignment Value\n",
-+ __func__);
-+ return retval;
-+ }
-+ }
-+ }
-+ return retval;
-+
-+}
-+
-+static int cfi_preproc_reset(struct dwc_otg_pcd *pcd,
-+ struct cfi_usb_ctrlrequest *req)
-+{
-+ int retval = 0;
-+
-+ switch (req->wIndex) {
-+ case 0:
-+ /* Reset all features */
-+ retval = cfi_handle_reset_all(pcd, req->wValue & 0xff);
-+ break;
-+
-+ case FT_ID_DMA_BUFFER_SETUP:
-+ /* Reset the SG buffer setup */
-+ retval =
-+ cfi_handle_reset_dma_buff_setup(pcd, req->wValue & 0xff);
-+ break;
-+
-+ case FT_ID_DMA_CONCAT_SETUP:
-+ /* Reset the Concatenation buffer setup */
-+ retval = cfi_handle_reset_concat_val(pcd, req->wValue & 0xff);
-+ break;
-+
-+ case FT_ID_DMA_BUFF_ALIGN:
-+ /* Reset the Alignment buffer setup */
-+ retval = cfi_handle_reset_align_val(pcd, req->wValue & 0xff);
-+ break;
-+
-+ case FT_ID_TX_FIFO_DEPTH:
-+ retval =
-+ cfi_handle_reset_fifo_val(pcd, req->wValue & 0xff, 0, 1);
-+ pcd->cfi->need_gadget_att = 0;
-+ break;
-+
-+ case FT_ID_RX_FIFO_DEPTH:
-+ retval = cfi_handle_reset_fifo_val(pcd, 0, 1, 0);
-+ pcd->cfi->need_gadget_att = 0;
-+ break;
-+ default:
-+ break;
-+ }
-+ return retval;
-+}
-+
-+/**
-+ * This function sets a new value for the SG buffer setup.
-+ */
-+static int cfi_ep_set_sg_val(uint8_t * buf, struct dwc_otg_pcd *pcd)
-+{
-+ uint8_t inaddr, outaddr;
-+ cfi_ep_t *epin, *epout;
-+ ddma_sg_buffer_setup_t *psgval;
-+ uint32_t desccount, size;
-+
-+ CFI_INFO("%s\n", __func__);
-+
-+ psgval = (ddma_sg_buffer_setup_t *) buf;
-+ desccount = (uint32_t) psgval->bCount;
-+ size = (uint32_t) psgval->wSize;
-+
-+ /* Check the DMA descriptor count */
-+ if ((desccount > MAX_DMA_DESCS_PER_EP) || (desccount == 0)) {
-+ CFI_INFO
-+ ("%s: The count of DMA Descriptors should be between 1 and %d\n",
-+ __func__, MAX_DMA_DESCS_PER_EP);
-+ return -DWC_E_INVALID;
-+ }
-+
-+ /* Check the DMA descriptor count */
-+
-+ if (size == 0) {
-+
-+ CFI_INFO("%s: The transfer size should be at least 1 byte\n",
-+ __func__);
-+
-+ return -DWC_E_INVALID;
-+
-+ }
-+
-+ inaddr = psgval->bInEndpointAddress;
-+ outaddr = psgval->bOutEndpointAddress;
-+
-+ epin = get_cfi_ep_by_addr(pcd->cfi, inaddr);
-+ epout = get_cfi_ep_by_addr(pcd->cfi, outaddr);
-+
-+ if (NULL == epin || NULL == epout) {
-+ CFI_INFO
-+ ("%s: Unable to get the endpoints inaddr=0x%02x outaddr=0x%02x\n",
-+ __func__, inaddr, outaddr);
-+ return -DWC_E_INVALID;
-+ }
-+
-+ epin->ep->dwc_ep.buff_mode = BM_SG;
-+ dwc_memcpy(epin->bm_sg, psgval, sizeof(ddma_sg_buffer_setup_t));
-+
-+ epout->ep->dwc_ep.buff_mode = BM_SG;
-+ dwc_memcpy(epout->bm_sg, psgval, sizeof(ddma_sg_buffer_setup_t));
-+
-+ return 0;
-+}
-+
-+/**
-+ * This function sets a new value for the buffer Alignment setup.
-+ */
-+static int cfi_ep_set_alignment_val(uint8_t * buf, struct dwc_otg_pcd *pcd)
-+{
-+ cfi_ep_t *ep;
-+ uint8_t addr;
-+ ddma_align_buffer_setup_t *palignval;
-+
-+ palignval = (ddma_align_buffer_setup_t *) buf;
-+ addr = palignval->bEndpointAddress;
-+
-+ ep = get_cfi_ep_by_addr(pcd->cfi, addr);
-+
-+ if (NULL == ep) {
-+ CFI_INFO("%s: Unable to get the endpoint addr=0x%02x\n",
-+ __func__, addr);
-+ return -DWC_E_INVALID;
-+ }
-+
-+ ep->ep->dwc_ep.buff_mode = BM_ALIGN;
-+ dwc_memcpy(ep->bm_align, palignval, sizeof(ddma_align_buffer_setup_t));
-+
-+ return 0;
-+}
-+
-+/**
-+ * This function sets a new value for the Concatenation buffer setup.
-+ */
-+static int cfi_ep_set_concat_val(uint8_t * buf, struct dwc_otg_pcd *pcd)
-+{
-+ uint8_t addr;
-+ cfi_ep_t *ep;
-+ struct _ddma_concat_buffer_setup_hdr *pConcatValHdr;
-+ uint16_t *pVals;
-+ uint32_t desccount;
-+ int i;
-+ uint16_t mps;
-+
-+ pConcatValHdr = (struct _ddma_concat_buffer_setup_hdr *)buf;
-+ desccount = (uint32_t) pConcatValHdr->bDescCount;
-+ pVals = (uint16_t *) (buf + BS_CONCAT_VAL_HDR_LEN);
-+
-+ /* Check the DMA descriptor count */
-+ if (desccount > MAX_DMA_DESCS_PER_EP) {
-+ CFI_INFO("%s: Maximum DMA Descriptor count should be %d\n",
-+ __func__, MAX_DMA_DESCS_PER_EP);
-+ return -DWC_E_INVALID;
-+ }
-+
-+ addr = pConcatValHdr->bEndpointAddress;
-+ ep = get_cfi_ep_by_addr(pcd->cfi, addr);
-+ if (NULL == ep) {
-+ CFI_INFO("%s: Unable to get the endpoint addr=0x%02x\n",
-+ __func__, addr);
-+ return -DWC_E_INVALID;
-+ }
-+
-+ mps = UGETW(ep->ep->desc->wMaxPacketSize);
-+
-+#if 0
-+ for (i = 0; i < desccount; i++) {
-+ CFI_INFO("%s: wTxSize[%d]=0x%04x\n", __func__, i, pVals[i]);
-+ }
-+ CFI_INFO("%s: epname=%s; mps=%d\n", __func__, ep->ep->ep.name, mps);
-+#endif
-+
-+ /* Check the wTxSizes to be less than or equal to the mps */
-+ for (i = 0; i < desccount; i++) {
-+ if (pVals[i] > mps) {
-+ CFI_INFO
-+ ("%s: ERROR - the wTxSize[%d] should be <= MPS (wTxSize=%d)\n",
-+ __func__, i, pVals[i]);
-+ return -DWC_E_INVALID;
-+ }
-+ }
-+
-+ ep->ep->dwc_ep.buff_mode = BM_CONCAT;
-+ dwc_memcpy(ep->bm_concat, pConcatValHdr, BS_CONCAT_VAL_HDR_LEN);
-+
-+ /* Free the previously allocated storage for the wTxBytes */
-+ if (ep->bm_concat->wTxBytes) {
-+ DWC_FREE(ep->bm_concat->wTxBytes);
-+ }
-+
-+ /* Allocate a new storage for the wTxBytes field */
-+ ep->bm_concat->wTxBytes =
-+ DWC_ALLOC(sizeof(uint16_t) * pConcatValHdr->bDescCount);
-+ if (NULL == ep->bm_concat->wTxBytes) {
-+ CFI_INFO("%s: Unable to allocate memory\n", __func__);
-+ return -DWC_E_NO_MEMORY;
-+ }
-+
-+ /* Copy the new values into the wTxBytes filed */
-+ dwc_memcpy(ep->bm_concat->wTxBytes, buf + BS_CONCAT_VAL_HDR_LEN,
-+ sizeof(uint16_t) * pConcatValHdr->bDescCount);
-+
-+ return 0;
-+}
-+
-+/**
-+ * This function calculates the total of all FIFO sizes
-+ *
-+ * @param core_if Programming view of DWC_otg controller
-+ *
-+ * @return The total of data FIFO sizes.
-+ *
-+ */
-+static uint16_t get_dfifo_size(dwc_otg_core_if_t * core_if)
-+{
-+ dwc_otg_core_params_t *params = core_if->core_params;
-+ uint16_t dfifo_total = 0;
-+ int i;
-+
-+ /* The shared RxFIFO size */
-+ dfifo_total =
-+ params->dev_rx_fifo_size + params->dev_nperio_tx_fifo_size;
-+
-+ /* Add up each TxFIFO size to the total */
-+ for (i = 0; i < core_if->hwcfg4.b.num_in_eps; i++) {
-+ dfifo_total += params->dev_tx_fifo_size[i];
-+ }
-+
-+ return dfifo_total;
-+}
-+
-+/**
-+ * This function returns Rx FIFO size
-+ *
-+ * @param core_if Programming view of DWC_otg controller
-+ *
-+ * @return The total of data FIFO sizes.
-+ *
-+ */
-+static int32_t get_rxfifo_size(dwc_otg_core_if_t * core_if, uint16_t wValue)
-+{
-+ switch (wValue >> 8) {
-+ case 0:
-+ return (core_if->pwron_rxfsiz <
-+ 32768) ? core_if->pwron_rxfsiz : 32768;
-+ break;
-+ case 1:
-+ return core_if->core_params->dev_rx_fifo_size;
-+ break;
-+ default:
-+ return -DWC_E_INVALID;
-+ break;
-+ }
-+}
-+
-+/**
-+ * This function returns Tx FIFO size for IN EP
-+ *
-+ * @param core_if Programming view of DWC_otg controller
-+ *
-+ * @return The total of data FIFO sizes.
-+ *
-+ */
-+static int32_t get_txfifo_size(struct dwc_otg_pcd *pcd, uint16_t wValue)
-+{
-+ dwc_otg_pcd_ep_t *ep;
-+
-+ ep = get_ep_by_addr(pcd, wValue & 0xff);
-+
-+ if (NULL == ep) {
-+ CFI_INFO("%s: Unable to get the endpoint addr=0x%02x\n",
-+ __func__, wValue & 0xff);
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if (!ep->dwc_ep.is_in) {
-+ CFI_INFO
-+ ("%s: No Tx FIFO assingned to the Out endpoint addr=0x%02x\n",
-+ __func__, wValue & 0xff);
-+ return -DWC_E_INVALID;
-+ }
-+
-+ switch (wValue >> 8) {
-+ case 0:
-+ return (GET_CORE_IF(pcd)->pwron_txfsiz
-+ [ep->dwc_ep.tx_fifo_num - 1] <
-+ 768) ? GET_CORE_IF(pcd)->pwron_txfsiz[ep->
-+ dwc_ep.tx_fifo_num
-+ - 1] : 32768;
-+ break;
-+ case 1:
-+ return GET_CORE_IF(pcd)->core_params->
-+ dev_tx_fifo_size[ep->dwc_ep.num - 1];
-+ break;
-+ default:
-+ return -DWC_E_INVALID;
-+ break;
-+ }
-+}
-+
-+/**
-+ * This function checks if the submitted combination of
-+ * device mode FIFO sizes is possible or not.
-+ *
-+ * @param core_if Programming view of DWC_otg controller
-+ *
-+ * @return 1 if possible, 0 otherwise.
-+ *
-+ */
-+static uint8_t check_fifo_sizes(dwc_otg_core_if_t * core_if)
-+{
-+ uint16_t dfifo_actual = 0;
-+ dwc_otg_core_params_t *params = core_if->core_params;
-+ uint16_t start_addr = 0;
-+ int i;
-+
-+ dfifo_actual =
-+ params->dev_rx_fifo_size + params->dev_nperio_tx_fifo_size;
-+
-+ for (i = 0; i < core_if->hwcfg4.b.num_in_eps; i++) {
-+ dfifo_actual += params->dev_tx_fifo_size[i];
-+ }
-+
-+ if (dfifo_actual > core_if->total_fifo_size) {
-+ return 0;
-+ }
-+
-+ if (params->dev_rx_fifo_size > 32768 || params->dev_rx_fifo_size < 16)
-+ return 0;
-+
-+ if (params->dev_nperio_tx_fifo_size > 32768
-+ || params->dev_nperio_tx_fifo_size < 16)
-+ return 0;
-+
-+ for (i = 0; i < core_if->hwcfg4.b.num_in_eps; i++) {
-+
-+ if (params->dev_tx_fifo_size[i] > 768
-+ || params->dev_tx_fifo_size[i] < 4)
-+ return 0;
-+ }
-+
-+ if (params->dev_rx_fifo_size > core_if->pwron_rxfsiz)
-+ return 0;
-+ start_addr = params->dev_rx_fifo_size;
-+
-+ if (params->dev_nperio_tx_fifo_size > core_if->pwron_gnptxfsiz)
-+ return 0;
-+ start_addr += params->dev_nperio_tx_fifo_size;
-+
-+ for (i = 0; i < core_if->hwcfg4.b.num_in_eps; i++) {
-+
-+ if (params->dev_tx_fifo_size[i] > core_if->pwron_txfsiz[i])
-+ return 0;
-+ start_addr += params->dev_tx_fifo_size[i];
-+ }
-+
-+ return 1;
-+}
-+
-+/**
-+ * This function resizes Device mode FIFOs
-+ *
-+ * @param core_if Programming view of DWC_otg controller
-+ *
-+ * @return 1 if successful, 0 otherwise
-+ *
-+ */
-+static uint8_t resize_fifos(dwc_otg_core_if_t * core_if)
-+{
-+ int i = 0;
-+ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs;
-+ dwc_otg_core_params_t *params = core_if->core_params;
-+ uint32_t rx_fifo_size;
-+ fifosize_data_t nptxfifosize;
-+ fifosize_data_t txfifosize[15];
-+
-+ uint32_t rx_fsz_bak;
-+ uint32_t nptxfsz_bak;
-+ uint32_t txfsz_bak[15];
-+
-+ uint16_t start_address;
-+ uint8_t retval = 1;
-+
-+ if (!check_fifo_sizes(core_if)) {
-+ return 0;
-+ }
-+
-+ /* Configure data FIFO sizes */
-+ if (core_if->hwcfg2.b.dynamic_fifo && params->enable_dynamic_fifo) {
-+ rx_fsz_bak = DWC_READ_REG32(&global_regs->grxfsiz);
-+ rx_fifo_size = params->dev_rx_fifo_size;
-+ DWC_WRITE_REG32(&global_regs->grxfsiz, rx_fifo_size);
-+
-+ /*
-+ * Tx FIFOs These FIFOs are numbered from 1 to 15.
-+ * Indexes of the FIFO size module parameters in the
-+ * dev_tx_fifo_size array and the FIFO size registers in
-+ * the dtxfsiz array run from 0 to 14.
-+ */
-+
-+ /* Non-periodic Tx FIFO */
-+ nptxfsz_bak = DWC_READ_REG32(&global_regs->gnptxfsiz);
-+ nptxfifosize.b.depth = params->dev_nperio_tx_fifo_size;
-+ start_address = params->dev_rx_fifo_size;
-+ nptxfifosize.b.startaddr = start_address;
-+
-+ DWC_WRITE_REG32(&global_regs->gnptxfsiz, nptxfifosize.d32);
-+
-+ start_address += nptxfifosize.b.depth;
-+
-+ for (i = 0; i < core_if->hwcfg4.b.num_in_eps; i++) {
-+ txfsz_bak[i] = DWC_READ_REG32(&global_regs->dtxfsiz[i]);
-+
-+ txfifosize[i].b.depth = params->dev_tx_fifo_size[i];
-+ txfifosize[i].b.startaddr = start_address;
-+ DWC_WRITE_REG32(&global_regs->dtxfsiz[i],
-+ txfifosize[i].d32);
-+
-+ start_address += txfifosize[i].b.depth;
-+ }
-+
-+ /** Check if register values are set correctly */
-+ if (rx_fifo_size != DWC_READ_REG32(&global_regs->grxfsiz)) {
-+ retval = 0;
-+ }
-+
-+ if (nptxfifosize.d32 != DWC_READ_REG32(&global_regs->gnptxfsiz)) {
-+ retval = 0;
-+ }
-+
-+ for (i = 0; i < core_if->hwcfg4.b.num_in_eps; i++) {
-+ if (txfifosize[i].d32 !=
-+ DWC_READ_REG32(&global_regs->dtxfsiz[i])) {
-+ retval = 0;
-+ }
-+ }
-+
-+ /** If register values are not set correctly, reset old values */
-+ if (retval == 0) {
-+ DWC_WRITE_REG32(&global_regs->grxfsiz, rx_fsz_bak);
-+
-+ /* Non-periodic Tx FIFO */
-+ DWC_WRITE_REG32(&global_regs->gnptxfsiz, nptxfsz_bak);
-+
-+ for (i = 0; i < core_if->hwcfg4.b.num_in_eps; i++) {
-+ DWC_WRITE_REG32(&global_regs->dtxfsiz[i],
-+ txfsz_bak[i]);
-+ }
-+ }
-+ } else {
-+ return 0;
-+ }
-+
-+ /* Flush the FIFOs */
-+ dwc_otg_flush_tx_fifo(core_if, 0x10); /* all Tx FIFOs */
-+ dwc_otg_flush_rx_fifo(core_if);
-+
-+ return retval;
-+}
-+
-+/**
-+ * This function sets a new value for the buffer Alignment setup.
-+ */
-+static int cfi_ep_set_tx_fifo_val(uint8_t * buf, dwc_otg_pcd_t * pcd)
-+{
-+ int retval;
-+ uint32_t fsiz;
-+ uint16_t size;
-+ uint16_t ep_addr;
-+ dwc_otg_pcd_ep_t *ep;
-+ dwc_otg_core_params_t *params = GET_CORE_IF(pcd)->core_params;
-+ tx_fifo_size_setup_t *ptxfifoval;
-+
-+ ptxfifoval = (tx_fifo_size_setup_t *) buf;
-+ ep_addr = ptxfifoval->bEndpointAddress;
-+ size = ptxfifoval->wDepth;
-+
-+ ep = get_ep_by_addr(pcd, ep_addr);
-+
-+ CFI_INFO
-+ ("%s: Set Tx FIFO size: endpoint addr=0x%02x, depth=%d, FIFO Num=%d\n",
-+ __func__, ep_addr, size, ep->dwc_ep.tx_fifo_num);
-+
-+ if (NULL == ep) {
-+ CFI_INFO("%s: Unable to get the endpoint addr=0x%02x\n",
-+ __func__, ep_addr);
-+ return -DWC_E_INVALID;
-+ }
-+
-+ fsiz = params->dev_tx_fifo_size[ep->dwc_ep.tx_fifo_num - 1];
-+ params->dev_tx_fifo_size[ep->dwc_ep.tx_fifo_num - 1] = size;
-+
-+ if (resize_fifos(GET_CORE_IF(pcd))) {
-+ retval = 0;
-+ } else {
-+ CFI_INFO
-+ ("%s: Error setting the feature Tx FIFO Size for EP%d\n",
-+ __func__, ep_addr);
-+ params->dev_tx_fifo_size[ep->dwc_ep.tx_fifo_num - 1] = fsiz;
-+ retval = -DWC_E_INVALID;
-+ }
-+
-+ return retval;
-+}
-+
-+/**
-+ * This function sets a new value for the buffer Alignment setup.
-+ */
-+static int cfi_set_rx_fifo_val(uint8_t * buf, dwc_otg_pcd_t * pcd)
-+{
-+ int retval;
-+ uint32_t fsiz;
-+ uint16_t size;
-+ dwc_otg_core_params_t *params = GET_CORE_IF(pcd)->core_params;
-+ rx_fifo_size_setup_t *prxfifoval;
-+
-+ prxfifoval = (rx_fifo_size_setup_t *) buf;
-+ size = prxfifoval->wDepth;
-+
-+ fsiz = params->dev_rx_fifo_size;
-+ params->dev_rx_fifo_size = size;
-+
-+ if (resize_fifos(GET_CORE_IF(pcd))) {
-+ retval = 0;
-+ } else {
-+ CFI_INFO("%s: Error setting the feature Rx FIFO Size\n",
-+ __func__);
-+ params->dev_rx_fifo_size = fsiz;
-+ retval = -DWC_E_INVALID;
-+ }
-+
-+ return retval;
-+}
-+
-+/**
-+ * This function reads the SG of an EP's buffer setup into the buffer buf
-+ */
-+static int cfi_ep_get_sg_val(uint8_t * buf, struct dwc_otg_pcd *pcd,
-+ struct cfi_usb_ctrlrequest *req)
-+{
-+ int retval = -DWC_E_INVALID;
-+ uint8_t addr;
-+ cfi_ep_t *ep;
-+
-+ /* The Low Byte of the wValue contains a non-zero address of the endpoint */
-+ addr = req->wValue & 0xFF;
-+ if (addr == 0) /* The address should be non-zero */
-+ return retval;
-+
-+ ep = get_cfi_ep_by_addr(pcd->cfi, addr);
-+ if (NULL == ep) {
-+ CFI_INFO("%s: Unable to get the endpoint address(0x%02x)\n",
-+ __func__, addr);
-+ return retval;
-+ }
-+
-+ dwc_memcpy(buf, ep->bm_sg, BS_SG_VAL_DESC_LEN);
-+ retval = BS_SG_VAL_DESC_LEN;
-+ return retval;
-+}
-+
-+/**
-+ * This function reads the Concatenation value of an EP's buffer mode into
-+ * the buffer buf
-+ */
-+static int cfi_ep_get_concat_val(uint8_t * buf, struct dwc_otg_pcd *pcd,
-+ struct cfi_usb_ctrlrequest *req)
-+{
-+ int retval = -DWC_E_INVALID;
-+ uint8_t addr;
-+ cfi_ep_t *ep;
-+ uint8_t desc_count;
-+
-+ /* The Low Byte of the wValue contains a non-zero address of the endpoint */
-+ addr = req->wValue & 0xFF;
-+ if (addr == 0) /* The address should be non-zero */
-+ return retval;
-+
-+ ep = get_cfi_ep_by_addr(pcd->cfi, addr);
-+ if (NULL == ep) {
-+ CFI_INFO("%s: Unable to get the endpoint address(0x%02x)\n",
-+ __func__, addr);
-+ return retval;
-+ }
-+
-+ /* Copy the header to the buffer */
-+ dwc_memcpy(buf, ep->bm_concat, BS_CONCAT_VAL_HDR_LEN);
-+ /* Advance the buffer pointer by the header size */
-+ buf += BS_CONCAT_VAL_HDR_LEN;
-+
-+ desc_count = ep->bm_concat->hdr.bDescCount;
-+ /* Copy alll the wTxBytes to the buffer */
-+ dwc_memcpy(buf, ep->bm_concat->wTxBytes, sizeof(uid16_t) * desc_count);
-+
-+ retval = BS_CONCAT_VAL_HDR_LEN + sizeof(uid16_t) * desc_count;
-+ return retval;
-+}
-+
-+/**
-+ * This function reads the buffer Alignment value of an EP's buffer mode into
-+ * the buffer buf
-+ *
-+ * @return The total number of bytes copied to the buffer or negative error code.
-+ */
-+static int cfi_ep_get_align_val(uint8_t * buf, struct dwc_otg_pcd *pcd,
-+ struct cfi_usb_ctrlrequest *req)
-+{
-+ int retval = -DWC_E_INVALID;
-+ uint8_t addr;
-+ cfi_ep_t *ep;
-+
-+ /* The Low Byte of the wValue contains a non-zero address of the endpoint */
-+ addr = req->wValue & 0xFF;
-+ if (addr == 0) /* The address should be non-zero */
-+ return retval;
-+
-+ ep = get_cfi_ep_by_addr(pcd->cfi, addr);
-+ if (NULL == ep) {
-+ CFI_INFO("%s: Unable to get the endpoint address(0x%02x)\n",
-+ __func__, addr);
-+ return retval;
-+ }
-+
-+ dwc_memcpy(buf, ep->bm_align, BS_ALIGN_VAL_HDR_LEN);
-+ retval = BS_ALIGN_VAL_HDR_LEN;
-+
-+ return retval;
-+}
-+
-+/**
-+ * This function sets a new value for the specified feature
-+ *
-+ * @param pcd A pointer to the PCD object
-+ *
-+ * @return 0 if successful, negative error code otherwise to stall the DCE.
-+ */
-+static int cfi_set_feature_value(struct dwc_otg_pcd *pcd)
-+{
-+ int retval = -DWC_E_NOT_SUPPORTED;
-+ uint16_t wIndex, wValue;
-+ uint8_t bRequest;
-+ struct dwc_otg_core_if *coreif;
-+ cfiobject_t *cfi = pcd->cfi;
-+ struct cfi_usb_ctrlrequest *ctrl_req;
-+ uint8_t *buf;
-+ ctrl_req = &cfi->ctrl_req;
-+
-+ buf = pcd->cfi->ctrl_req.data;
-+
-+ coreif = GET_CORE_IF(pcd);
-+ bRequest = ctrl_req->bRequest;
-+ wIndex = DWC_CONSTANT_CPU_TO_LE16(ctrl_req->wIndex);
-+ wValue = DWC_CONSTANT_CPU_TO_LE16(ctrl_req->wValue);
-+
-+ /* See which feature is to be modified */
-+ switch (wIndex) {
-+ case FT_ID_DMA_BUFFER_SETUP:
-+ /* Modify the feature */
-+ if ((retval = cfi_ep_set_sg_val(buf, pcd)) < 0)
-+ return retval;
-+
-+ /* And send this request to the gadget */
-+ cfi->need_gadget_att = 1;
-+ break;
-+
-+ case FT_ID_DMA_BUFF_ALIGN:
-+ if ((retval = cfi_ep_set_alignment_val(buf, pcd)) < 0)
-+ return retval;
-+ cfi->need_gadget_att = 1;
-+ break;
-+
-+ case FT_ID_DMA_CONCAT_SETUP:
-+ /* Modify the feature */
-+ if ((retval = cfi_ep_set_concat_val(buf, pcd)) < 0)
-+ return retval;
-+ cfi->need_gadget_att = 1;
-+ break;
-+
-+ case FT_ID_DMA_CIRCULAR:
-+ CFI_INFO("FT_ID_DMA_CIRCULAR\n");
-+ break;
-+
-+ case FT_ID_THRESHOLD_SETUP:
-+ CFI_INFO("FT_ID_THRESHOLD_SETUP\n");
-+ break;
-+
-+ case FT_ID_DFIFO_DEPTH:
-+ CFI_INFO("FT_ID_DFIFO_DEPTH\n");
-+ break;
-+
-+ case FT_ID_TX_FIFO_DEPTH:
-+ CFI_INFO("FT_ID_TX_FIFO_DEPTH\n");
-+ if ((retval = cfi_ep_set_tx_fifo_val(buf, pcd)) < 0)
-+ return retval;
-+ cfi->need_gadget_att = 0;
-+ break;
-+
-+ case FT_ID_RX_FIFO_DEPTH:
-+ CFI_INFO("FT_ID_RX_FIFO_DEPTH\n");
-+ if ((retval = cfi_set_rx_fifo_val(buf, pcd)) < 0)
-+ return retval;
-+ cfi->need_gadget_att = 0;
-+ break;
-+ }
-+
-+ return retval;
-+}
-+
-+#endif //DWC_UTE_CFI
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_cfi.h
-@@ -0,0 +1,320 @@
-+/* ==========================================================================
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+
-+#if !defined(__DWC_OTG_CFI_H__)
-+#define __DWC_OTG_CFI_H__
-+
-+#include "dwc_otg_pcd.h"
-+#include "dwc_cfi_common.h"
-+
-+/**
-+ * @file
-+ * This file contains the CFI related OTG PCD specific common constants,
-+ * interfaces(functions and macros) and data structures.The CFI Protocol is an
-+ * optional interface for internal testing purposes that a DUT may implement to
-+ * support testing of configurable features.
-+ *
-+ */
-+
-+struct dwc_otg_pcd;
-+struct dwc_otg_pcd_ep;
-+
-+/** OTG CFI Features (properties) ID constants */
-+/** This is a request for all Core Features */
-+#define FT_ID_DMA_MODE 0x0001
-+#define FT_ID_DMA_BUFFER_SETUP 0x0002
-+#define FT_ID_DMA_BUFF_ALIGN 0x0003
-+#define FT_ID_DMA_CONCAT_SETUP 0x0004
-+#define FT_ID_DMA_CIRCULAR 0x0005
-+#define FT_ID_THRESHOLD_SETUP 0x0006
-+#define FT_ID_DFIFO_DEPTH 0x0007
-+#define FT_ID_TX_FIFO_DEPTH 0x0008
-+#define FT_ID_RX_FIFO_DEPTH 0x0009
-+
-+/**********************************************************/
-+#define CFI_INFO_DEF
-+
-+#ifdef CFI_INFO_DEF
-+#define CFI_INFO(fmt...) DWC_PRINTF("CFI: " fmt);
-+#else
-+#define CFI_INFO(fmt...)
-+#endif
-+
-+#define min(x,y) ({ \
-+ x < y ? x : y; })
-+
-+#define max(x,y) ({ \
-+ x > y ? x : y; })
-+
-+/**
-+ * Descriptor DMA SG Buffer setup structure (SG buffer). This structure is
-+ * also used for setting up a buffer for Circular DDMA.
-+ */
-+struct _ddma_sg_buffer_setup {
-+#define BS_SG_VAL_DESC_LEN 6
-+ /* The OUT EP address */
-+ uint8_t bOutEndpointAddress;
-+ /* The IN EP address */
-+ uint8_t bInEndpointAddress;
-+ /* Number of bytes to put between transfer segments (must be DWORD boundaries) */
-+ uint8_t bOffset;
-+ /* The number of transfer segments (a DMA descriptors per each segment) */
-+ uint8_t bCount;
-+ /* Size (in byte) of each transfer segment */
-+ uint16_t wSize;
-+} __attribute__ ((packed));
-+typedef struct _ddma_sg_buffer_setup ddma_sg_buffer_setup_t;
-+
-+/** Descriptor DMA Concatenation Buffer setup structure */
-+struct _ddma_concat_buffer_setup_hdr {
-+#define BS_CONCAT_VAL_HDR_LEN 4
-+ /* The endpoint for which the buffer is to be set up */
-+ uint8_t bEndpointAddress;
-+ /* The count of descriptors to be used */
-+ uint8_t bDescCount;
-+ /* The total size of the transfer */
-+ uint16_t wSize;
-+} __attribute__ ((packed));
-+typedef struct _ddma_concat_buffer_setup_hdr ddma_concat_buffer_setup_hdr_t;
-+
-+/** Descriptor DMA Concatenation Buffer setup structure */
-+struct _ddma_concat_buffer_setup {
-+ /* The SG header */
-+ ddma_concat_buffer_setup_hdr_t hdr;
-+
-+ /* The XFER sizes pointer (allocated dynamically) */
-+ uint16_t *wTxBytes;
-+} __attribute__ ((packed));
-+typedef struct _ddma_concat_buffer_setup ddma_concat_buffer_setup_t;
-+
-+/** Descriptor DMA Alignment Buffer setup structure */
-+struct _ddma_align_buffer_setup {
-+#define BS_ALIGN_VAL_HDR_LEN 2
-+ uint8_t bEndpointAddress;
-+ uint8_t bAlign;
-+} __attribute__ ((packed));
-+typedef struct _ddma_align_buffer_setup ddma_align_buffer_setup_t;
-+
-+/** Transmit FIFO Size setup structure */
-+struct _tx_fifo_size_setup {
-+ uint8_t bEndpointAddress;
-+ uint16_t wDepth;
-+} __attribute__ ((packed));
-+typedef struct _tx_fifo_size_setup tx_fifo_size_setup_t;
-+
-+/** Transmit FIFO Size setup structure */
-+struct _rx_fifo_size_setup {
-+ uint16_t wDepth;
-+} __attribute__ ((packed));
-+typedef struct _rx_fifo_size_setup rx_fifo_size_setup_t;
-+
-+/**
-+ * struct cfi_usb_ctrlrequest - the CFI implementation of the struct usb_ctrlrequest
-+ * This structure encapsulates the standard usb_ctrlrequest and adds a pointer
-+ * to the data returned in the data stage of a 3-stage Control Write requests.
-+ */
-+struct cfi_usb_ctrlrequest {
-+ uint8_t bRequestType;
-+ uint8_t bRequest;
-+ uint16_t wValue;
-+ uint16_t wIndex;
-+ uint16_t wLength;
-+ uint8_t *data;
-+} UPACKED;
-+
-+/*---------------------------------------------------------------------------*/
-+
-+/**
-+ * The CFI wrapper of the enabled and activated dwc_otg_pcd_ep structures.
-+ * This structure is used to store the buffer setup data for any
-+ * enabled endpoint in the PCD.
-+ */
-+struct cfi_ep {
-+ /* Entry for the list container */
-+ dwc_list_link_t lh;
-+ /* Pointer to the active PCD endpoint structure */
-+ struct dwc_otg_pcd_ep *ep;
-+ /* The last descriptor in the chain of DMA descriptors of the endpoint */
-+ struct dwc_otg_dma_desc *dma_desc_last;
-+ /* The SG feature value */
-+ ddma_sg_buffer_setup_t *bm_sg;
-+ /* The Circular feature value */
-+ ddma_sg_buffer_setup_t *bm_circ;
-+ /* The Concatenation feature value */
-+ ddma_concat_buffer_setup_t *bm_concat;
-+ /* The Alignment feature value */
-+ ddma_align_buffer_setup_t *bm_align;
-+ /* XFER length */
-+ uint32_t xfer_len;
-+ /*
-+ * Count of DMA descriptors currently used.
-+ * The total should not exceed the MAX_DMA_DESCS_PER_EP value
-+ * defined in the dwc_otg_cil.h
-+ */
-+ uint32_t desc_count;
-+};
-+typedef struct cfi_ep cfi_ep_t;
-+
-+typedef struct cfi_dma_buff {
-+#define CFI_IN_BUF_LEN 1024
-+#define CFI_OUT_BUF_LEN 1024
-+ dma_addr_t addr;
-+ uint8_t *buf;
-+} cfi_dma_buff_t;
-+
-+struct cfiobject;
-+
-+/**
-+ * This is the interface for the CFI operations.
-+ *
-+ * @param ep_enable Called when any endpoint is enabled and activated.
-+ * @param release Called when the CFI object is released and it needs to correctly
-+ * deallocate the dynamic memory
-+ * @param ctrl_write_complete Called when the data stage of the request is complete
-+ */
-+typedef struct cfi_ops {
-+ int (*ep_enable) (struct cfiobject * cfi, struct dwc_otg_pcd * pcd,
-+ struct dwc_otg_pcd_ep * ep);
-+ void *(*ep_alloc_buf) (struct cfiobject * cfi, struct dwc_otg_pcd * pcd,
-+ struct dwc_otg_pcd_ep * ep, dma_addr_t * dma,
-+ unsigned size, gfp_t flags);
-+ void (*release) (struct cfiobject * cfi);
-+ int (*ctrl_write_complete) (struct cfiobject * cfi,
-+ struct dwc_otg_pcd * pcd);
-+ void (*build_descriptors) (struct cfiobject * cfi,
-+ struct dwc_otg_pcd * pcd,
-+ struct dwc_otg_pcd_ep * ep,
-+ dwc_otg_pcd_request_t * req);
-+} cfi_ops_t;
-+
-+struct cfiobject {
-+ cfi_ops_t ops;
-+ struct dwc_otg_pcd *pcd;
-+ struct usb_gadget *gadget;
-+
-+ /* Buffers used to send/receive CFI-related request data */
-+ cfi_dma_buff_t buf_in;
-+ cfi_dma_buff_t buf_out;
-+
-+ /* CFI specific Control request wrapper */
-+ struct cfi_usb_ctrlrequest ctrl_req;
-+
-+ /* The list of active EP's in the PCD of type cfi_ep_t */
-+ dwc_list_link_t active_eps;
-+
-+ /* This flag shall control the propagation of a specific request
-+ * to the gadget's processing routines.
-+ * 0 - no gadget handling
-+ * 1 - the gadget needs to know about this request (w/o completing a status
-+ * phase - just return a 0 to the _setup callback)
-+ */
-+ uint8_t need_gadget_att;
-+
-+ /* Flag indicating whether the status IN phase needs to be
-+ * completed by the PCD
-+ */
-+ uint8_t need_status_in_complete;
-+};
-+typedef struct cfiobject cfiobject_t;
-+
-+#define DUMP_MSG
-+
-+#if defined(DUMP_MSG)
-+static inline void dump_msg(const u8 * buf, unsigned int length)
-+{
-+ unsigned int start, num, i;
-+ char line[52], *p;
-+
-+ if (length >= 512)
-+ return;
-+
-+ start = 0;
-+ while (length > 0) {
-+ num = min(length, 16u);
-+ p = line;
-+ for (i = 0; i < num; ++i) {
-+ if (i == 8)
-+ *p++ = ' ';
-+ DWC_SPRINTF(p, " %02x", buf[i]);
-+ p += 3;
-+ }
-+ *p = 0;
-+ DWC_DEBUG("%6x: %s\n", start, line);
-+ buf += num;
-+ start += num;
-+ length -= num;
-+ }
-+}
-+#else
-+static inline void dump_msg(const u8 * buf, unsigned int length)
-+{
-+}
-+#endif
-+
-+/**
-+ * This function returns a pointer to cfi_ep_t object with the addr address.
-+ */
-+static inline struct cfi_ep *get_cfi_ep_by_addr(struct cfiobject *cfi,
-+ uint8_t addr)
-+{
-+ struct cfi_ep *pcfiep;
-+ dwc_list_link_t *tmp;
-+
-+ DWC_LIST_FOREACH(tmp, &cfi->active_eps) {
-+ pcfiep = DWC_LIST_ENTRY(tmp, struct cfi_ep, lh);
-+
-+ if (pcfiep->ep->desc->bEndpointAddress == addr) {
-+ return pcfiep;
-+ }
-+ }
-+
-+ return NULL;
-+}
-+
-+/**
-+ * This function returns a pointer to cfi_ep_t object that matches
-+ * the dwc_otg_pcd_ep object.
-+ */
-+static inline struct cfi_ep *get_cfi_ep_by_pcd_ep(struct cfiobject *cfi,
-+ struct dwc_otg_pcd_ep *ep)
-+{
-+ struct cfi_ep *pcfiep = NULL;
-+ dwc_list_link_t *tmp;
-+
-+ DWC_LIST_FOREACH(tmp, &cfi->active_eps) {
-+ pcfiep = DWC_LIST_ENTRY(tmp, struct cfi_ep, lh);
-+ if (pcfiep->ep == ep) {
-+ return pcfiep;
-+ }
-+ }
-+ return NULL;
-+}
-+
-+int cfi_setup(struct dwc_otg_pcd *pcd, struct cfi_usb_ctrlrequest *ctrl);
-+
-+#endif /* (__DWC_OTG_CFI_H__) */
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_cil.c
-@@ -0,0 +1,7141 @@
-+/* ==========================================================================
-+ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_cil.c $
-+ * $Revision: #191 $
-+ * $Date: 2012/08/10 $
-+ * $Change: 2047372 $
-+ *
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+
-+/** @file
-+ *
-+ * The Core Interface Layer provides basic services for accessing and
-+ * managing the DWC_otg hardware. These services are used by both the
-+ * Host Controller Driver and the Peripheral Controller Driver.
-+ *
-+ * The CIL manages the memory map for the core so that the HCD and PCD
-+ * don't have to do this separately. It also handles basic tasks like
-+ * reading/writing the registers and data FIFOs in the controller.
-+ * Some of the data access functions provide encapsulation of several
-+ * operations required to perform a task, such as writing multiple
-+ * registers to start a transfer. Finally, the CIL performs basic
-+ * services that are not specific to either the host or device modes
-+ * of operation. These services include management of the OTG Host
-+ * Negotiation Protocol (HNP) and Session Request Protocol (SRP). A
-+ * Diagnostic API is also provided to allow testing of the controller
-+ * hardware.
-+ *
-+ * The Core Interface Layer has the following requirements:
-+ * - Provides basic controller operations.
-+ * - Minimal use of OS services.
-+ * - The OS services used will be abstracted by using inline functions
-+ * or macros.
-+ *
-+ */
-+
-+#include "dwc_os.h"
-+#include "dwc_otg_regs.h"
-+#include "dwc_otg_cil.h"
-+
-+static int dwc_otg_setup_params(dwc_otg_core_if_t * core_if);
-+
-+/**
-+ * This function is called to initialize the DWC_otg CSR data
-+ * structures. The register addresses in the device and host
-+ * structures are initialized from the base address supplied by the
-+ * caller. The calling function must make the OS calls to get the
-+ * base address of the DWC_otg controller registers. The core_params
-+ * argument holds the parameters that specify how the core should be
-+ * configured.
-+ *
-+ * @param reg_base_addr Base address of DWC_otg core registers
-+ *
-+ */
-+dwc_otg_core_if_t *dwc_otg_cil_init(const uint32_t * reg_base_addr)
-+{
-+ dwc_otg_core_if_t *core_if = 0;
-+ dwc_otg_dev_if_t *dev_if = 0;
-+ dwc_otg_host_if_t *host_if = 0;
-+ uint8_t *reg_base = (uint8_t *) reg_base_addr;
-+ int i = 0;
-+
-+ DWC_DEBUGPL(DBG_CILV, "%s(%p)\n", __func__, reg_base_addr);
-+
-+ core_if = DWC_ALLOC(sizeof(dwc_otg_core_if_t));
-+
-+ if (core_if == NULL) {
-+ DWC_DEBUGPL(DBG_CIL,
-+ "Allocation of dwc_otg_core_if_t failed\n");
-+ return 0;
-+ }
-+ core_if->core_global_regs = (dwc_otg_core_global_regs_t *) reg_base;
-+
-+ /*
-+ * Allocate the Device Mode structures.
-+ */
-+ dev_if = DWC_ALLOC(sizeof(dwc_otg_dev_if_t));
-+
-+ if (dev_if == NULL) {
-+ DWC_DEBUGPL(DBG_CIL, "Allocation of dwc_otg_dev_if_t failed\n");
-+ DWC_FREE(core_if);
-+ return 0;
-+ }
-+
-+ dev_if->dev_global_regs =
-+ (dwc_otg_device_global_regs_t *) (reg_base +
-+ DWC_DEV_GLOBAL_REG_OFFSET);
-+
-+ for (i = 0; i < MAX_EPS_CHANNELS; i++) {
-+ dev_if->in_ep_regs[i] = (dwc_otg_dev_in_ep_regs_t *)
-+ (reg_base + DWC_DEV_IN_EP_REG_OFFSET +
-+ (i * DWC_EP_REG_OFFSET));
-+
-+ dev_if->out_ep_regs[i] = (dwc_otg_dev_out_ep_regs_t *)
-+ (reg_base + DWC_DEV_OUT_EP_REG_OFFSET +
-+ (i * DWC_EP_REG_OFFSET));
-+ DWC_DEBUGPL(DBG_CILV, "in_ep_regs[%d]->diepctl=%p\n",
-+ i, &dev_if->in_ep_regs[i]->diepctl);
-+ DWC_DEBUGPL(DBG_CILV, "out_ep_regs[%d]->doepctl=%p\n",
-+ i, &dev_if->out_ep_regs[i]->doepctl);
-+ }
-+
-+ dev_if->speed = 0; // unknown
-+
-+ core_if->dev_if = dev_if;
-+
-+ /*
-+ * Allocate the Host Mode structures.
-+ */
-+ host_if = DWC_ALLOC(sizeof(dwc_otg_host_if_t));
-+
-+ if (host_if == NULL) {
-+ DWC_DEBUGPL(DBG_CIL,
-+ "Allocation of dwc_otg_host_if_t failed\n");
-+ DWC_FREE(dev_if);
-+ DWC_FREE(core_if);
-+ return 0;
-+ }
-+
-+ host_if->host_global_regs = (dwc_otg_host_global_regs_t *)
-+ (reg_base + DWC_OTG_HOST_GLOBAL_REG_OFFSET);
-+
-+ host_if->hprt0 =
-+ (uint32_t *) (reg_base + DWC_OTG_HOST_PORT_REGS_OFFSET);
-+
-+ for (i = 0; i < MAX_EPS_CHANNELS; i++) {
-+ host_if->hc_regs[i] = (dwc_otg_hc_regs_t *)
-+ (reg_base + DWC_OTG_HOST_CHAN_REGS_OFFSET +
-+ (i * DWC_OTG_CHAN_REGS_OFFSET));
-+ DWC_DEBUGPL(DBG_CILV, "hc_reg[%d]->hcchar=%p\n",
-+ i, &host_if->hc_regs[i]->hcchar);
-+ }
-+
-+ host_if->num_host_channels = MAX_EPS_CHANNELS;
-+ core_if->host_if = host_if;
-+
-+ for (i = 0; i < MAX_EPS_CHANNELS; i++) {
-+ core_if->data_fifo[i] =
-+ (uint32_t *) (reg_base + DWC_OTG_DATA_FIFO_OFFSET +
-+ (i * DWC_OTG_DATA_FIFO_SIZE));
-+ DWC_DEBUGPL(DBG_CILV, "data_fifo[%d]=0x%08lx\n",
-+ i, (unsigned long)core_if->data_fifo[i]);
-+ }
-+
-+ core_if->pcgcctl = (uint32_t *) (reg_base + DWC_OTG_PCGCCTL_OFFSET);
-+
-+ /* Initiate lx_state to L3 disconnected state */
-+ core_if->lx_state = DWC_OTG_L3;
-+ /*
-+ * Store the contents of the hardware configuration registers here for
-+ * easy access later.
-+ */
-+ core_if->hwcfg1.d32 =
-+ DWC_READ_REG32(&core_if->core_global_regs->ghwcfg1);
-+ core_if->hwcfg2.d32 =
-+ DWC_READ_REG32(&core_if->core_global_regs->ghwcfg2);
-+ core_if->hwcfg3.d32 =
-+ DWC_READ_REG32(&core_if->core_global_regs->ghwcfg3);
-+ core_if->hwcfg4.d32 =
-+ DWC_READ_REG32(&core_if->core_global_regs->ghwcfg4);
-+
-+ /* Force host mode to get HPTXFSIZ exact power on value */
-+ {
-+ gusbcfg_data_t gusbcfg = {.d32 = 0 };
-+ gusbcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->gusbcfg);
-+ gusbcfg.b.force_host_mode = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gusbcfg, gusbcfg.d32);
-+ dwc_mdelay(100);
-+ core_if->hptxfsiz.d32 =
-+ DWC_READ_REG32(&core_if->core_global_regs->hptxfsiz);
-+ gusbcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->gusbcfg);
-+ gusbcfg.b.force_host_mode = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gusbcfg, gusbcfg.d32);
-+ dwc_mdelay(100);
-+ }
-+
-+ DWC_DEBUGPL(DBG_CILV, "hwcfg1=%08x\n", core_if->hwcfg1.d32);
-+ DWC_DEBUGPL(DBG_CILV, "hwcfg2=%08x\n", core_if->hwcfg2.d32);
-+ DWC_DEBUGPL(DBG_CILV, "hwcfg3=%08x\n", core_if->hwcfg3.d32);
-+ DWC_DEBUGPL(DBG_CILV, "hwcfg4=%08x\n", core_if->hwcfg4.d32);
-+
-+ core_if->hcfg.d32 =
-+ DWC_READ_REG32(&core_if->host_if->host_global_regs->hcfg);
-+ core_if->dcfg.d32 =
-+ DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dcfg);
-+
-+ DWC_DEBUGPL(DBG_CILV, "hcfg=%08x\n", core_if->hcfg.d32);
-+ DWC_DEBUGPL(DBG_CILV, "dcfg=%08x\n", core_if->dcfg.d32);
-+
-+ DWC_DEBUGPL(DBG_CILV, "op_mode=%0x\n", core_if->hwcfg2.b.op_mode);
-+ DWC_DEBUGPL(DBG_CILV, "arch=%0x\n", core_if->hwcfg2.b.architecture);
-+ DWC_DEBUGPL(DBG_CILV, "num_dev_ep=%d\n", core_if->hwcfg2.b.num_dev_ep);
-+ DWC_DEBUGPL(DBG_CILV, "num_host_chan=%d\n",
-+ core_if->hwcfg2.b.num_host_chan);
-+ DWC_DEBUGPL(DBG_CILV, "nonperio_tx_q_depth=0x%0x\n",
-+ core_if->hwcfg2.b.nonperio_tx_q_depth);
-+ DWC_DEBUGPL(DBG_CILV, "host_perio_tx_q_depth=0x%0x\n",
-+ core_if->hwcfg2.b.host_perio_tx_q_depth);
-+ DWC_DEBUGPL(DBG_CILV, "dev_token_q_depth=0x%0x\n",
-+ core_if->hwcfg2.b.dev_token_q_depth);
-+
-+ DWC_DEBUGPL(DBG_CILV, "Total FIFO SZ=%d\n",
-+ core_if->hwcfg3.b.dfifo_depth);
-+ DWC_DEBUGPL(DBG_CILV, "xfer_size_cntr_width=%0x\n",
-+ core_if->hwcfg3.b.xfer_size_cntr_width);
-+
-+ /*
-+ * Set the SRP sucess bit for FS-I2c
-+ */
-+ core_if->srp_success = 0;
-+ core_if->srp_timer_started = 0;
-+
-+ /*
-+ * Create new workqueue and init works
-+ */
-+ core_if->wq_otg = DWC_WORKQ_ALLOC("dwc_otg");
-+ if (core_if->wq_otg == 0) {
-+ DWC_WARN("DWC_WORKQ_ALLOC failed\n");
-+ DWC_FREE(host_if);
-+ DWC_FREE(dev_if);
-+ DWC_FREE(core_if);
-+ return 0;
-+ }
-+
-+ core_if->snpsid = DWC_READ_REG32(&core_if->core_global_regs->gsnpsid);
-+
-+ DWC_PRINTF("Core Release: %x.%x%x%x\n",
-+ (core_if->snpsid >> 12 & 0xF),
-+ (core_if->snpsid >> 8 & 0xF),
-+ (core_if->snpsid >> 4 & 0xF), (core_if->snpsid & 0xF));
-+
-+ core_if->wkp_timer = DWC_TIMER_ALLOC("Wake Up Timer",
-+ w_wakeup_detected, core_if);
-+ if (core_if->wkp_timer == 0) {
-+ DWC_WARN("DWC_TIMER_ALLOC failed\n");
-+ DWC_FREE(host_if);
-+ DWC_FREE(dev_if);
-+ DWC_WORKQ_FREE(core_if->wq_otg);
-+ DWC_FREE(core_if);
-+ return 0;
-+ }
-+
-+ if (dwc_otg_setup_params(core_if)) {
-+ DWC_WARN("Error while setting core params\n");
-+ }
-+
-+ core_if->hibernation_suspend = 0;
-+
-+ /** ADP initialization */
-+ dwc_otg_adp_init(core_if);
-+
-+ return core_if;
-+}
-+
-+/**
-+ * This function frees the structures allocated by dwc_otg_cil_init().
-+ *
-+ * @param core_if The core interface pointer returned from
-+ * dwc_otg_cil_init().
-+ *
-+ */
-+void dwc_otg_cil_remove(dwc_otg_core_if_t * core_if)
-+{
-+ dctl_data_t dctl = {.d32 = 0 };
-+ DWC_DEBUGPL(DBG_CILV, "%s(%p)\n", __func__, core_if);
-+
-+ /* Disable all interrupts */
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gahbcfg, 1, 0);
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintmsk, 0);
-+
-+ dctl.b.sftdiscon = 1;
-+ if (core_if->snpsid >= OTG_CORE_REV_3_00a) {
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl, 0,
-+ dctl.d32);
-+ }
-+
-+ if (core_if->wq_otg) {
-+ DWC_WORKQ_WAIT_WORK_DONE(core_if->wq_otg, 500);
-+ DWC_WORKQ_FREE(core_if->wq_otg);
-+ }
-+ if (core_if->dev_if) {
-+ DWC_FREE(core_if->dev_if);
-+ }
-+ if (core_if->host_if) {
-+ DWC_FREE(core_if->host_if);
-+ }
-+
-+ /** Remove ADP Stuff */
-+ dwc_otg_adp_remove(core_if);
-+ if (core_if->core_params) {
-+ DWC_FREE(core_if->core_params);
-+ }
-+ if (core_if->wkp_timer) {
-+ DWC_TIMER_FREE(core_if->wkp_timer);
-+ }
-+ if (core_if->srp_timer) {
-+ DWC_TIMER_FREE(core_if->srp_timer);
-+ }
-+ DWC_FREE(core_if);
-+}
-+
-+/**
-+ * This function enables the controller's Global Interrupt in the AHB Config
-+ * register.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ */
-+void dwc_otg_enable_global_interrupts(dwc_otg_core_if_t * core_if)
-+{
-+ gahbcfg_data_t ahbcfg = {.d32 = 0 };
-+ ahbcfg.b.glblintrmsk = 1; /* Enable interrupts */
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gahbcfg, 0, ahbcfg.d32);
-+}
-+
-+/**
-+ * This function disables the controller's Global Interrupt in the AHB Config
-+ * register.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ */
-+void dwc_otg_disable_global_interrupts(dwc_otg_core_if_t * core_if)
-+{
-+ gahbcfg_data_t ahbcfg = {.d32 = 0 };
-+ ahbcfg.b.glblintrmsk = 1; /* Disable interrupts */
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gahbcfg, ahbcfg.d32, 0);
-+}
-+
-+/**
-+ * This function initializes the commmon interrupts, used in both
-+ * device and host modes.
-+ *
-+ * @param core_if Programming view of the DWC_otg controller
-+ *
-+ */
-+static void dwc_otg_enable_common_interrupts(dwc_otg_core_if_t * core_if)
-+{
-+ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs;
-+ gintmsk_data_t intr_mask = {.d32 = 0 };
-+
-+ /* Clear any pending OTG Interrupts */
-+ DWC_WRITE_REG32(&global_regs->gotgint, 0xFFFFFFFF);
-+
-+ /* Clear any pending interrupts */
-+ DWC_WRITE_REG32(&global_regs->gintsts, 0xFFFFFFFF);
-+
-+ /*
-+ * Enable the interrupts in the GINTMSK.
-+ */
-+ intr_mask.b.modemismatch = 1;
-+ intr_mask.b.otgintr = 1;
-+
-+ if (!core_if->dma_enable) {
-+ intr_mask.b.rxstsqlvl = 1;
-+ }
-+
-+ intr_mask.b.conidstschng = 1;
-+ intr_mask.b.wkupintr = 1;
-+ intr_mask.b.disconnect = 0;
-+ intr_mask.b.usbsuspend = 1;
-+ intr_mask.b.sessreqintr = 1;
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+ if (core_if->core_params->lpm_enable) {
-+ intr_mask.b.lpmtranrcvd = 1;
-+ }
-+#endif
-+ DWC_WRITE_REG32(&global_regs->gintmsk, intr_mask.d32);
-+}
-+
-+/*
-+ * The restore operation is modified to support Synopsys Emulated Powerdown and
-+ * Hibernation. This function is for exiting from Device mode hibernation by
-+ * Host Initiated Resume/Reset and Device Initiated Remote-Wakeup.
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param rem_wakeup - indicates whether resume is initiated by Device or Host.
-+ * @param reset - indicates whether resume is initiated by Reset.
-+ */
-+int dwc_otg_device_hibernation_restore(dwc_otg_core_if_t * core_if,
-+ int rem_wakeup, int reset)
-+{
-+ gpwrdn_data_t gpwrdn = {.d32 = 0 };
-+ pcgcctl_data_t pcgcctl = {.d32 = 0 };
-+ dctl_data_t dctl = {.d32 = 0 };
-+
-+ int timeout = 2000;
-+
-+ if (!core_if->hibernation_suspend) {
-+ DWC_PRINTF("Already exited from Hibernation\n");
-+ return 1;
-+ }
-+
-+ DWC_DEBUGPL(DBG_PCD, "%s called\n", __FUNCTION__);
-+ /* Switch-on voltage to the core */
-+ gpwrdn.b.pwrdnswtch = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ dwc_udelay(10);
-+
-+ /* Reset core */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnrstn = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ dwc_udelay(10);
-+
-+ /* Assert Restore signal */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.restore = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32);
-+ dwc_udelay(10);
-+
-+ /* Disable power clamps */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnclmp = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+
-+ if (rem_wakeup) {
-+ dwc_udelay(70);
-+ }
-+
-+ /* Deassert Reset core */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnrstn = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32);
-+ dwc_udelay(10);
-+
-+ /* Disable PMU interrupt */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuintsel = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+
-+ /* Mask interrupts from gpwrdn */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.connect_det_msk = 1;
-+ gpwrdn.b.srp_det_msk = 1;
-+ gpwrdn.b.disconn_det_msk = 1;
-+ gpwrdn.b.rst_det_msk = 1;
-+ gpwrdn.b.lnstchng_msk = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+
-+ /* Indicates that we are going out from hibernation */
-+ core_if->hibernation_suspend = 0;
-+
-+ /*
-+ * Set Restore Essential Regs bit in PCGCCTL register, restore_mode = 1
-+ * indicates restore from remote_wakeup
-+ */
-+ restore_essential_regs(core_if, rem_wakeup, 0);
-+
-+ /*
-+ * Wait a little for seeing new value of variable hibernation_suspend if
-+ * Restore done interrupt received before polling
-+ */
-+ dwc_udelay(10);
-+
-+ if (core_if->hibernation_suspend == 0) {
-+ /*
-+ * Wait For Restore_done Interrupt. This mechanism of polling the
-+ * interrupt is introduced to avoid any possible race conditions
-+ */
-+ do {
-+ gintsts_data_t gintsts;
-+ gintsts.d32 =
-+ DWC_READ_REG32(&core_if->core_global_regs->gintsts);
-+ if (gintsts.b.restoredone) {
-+ gintsts.d32 = 0;
-+ gintsts.b.restoredone = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->
-+ gintsts, gintsts.d32);
-+ DWC_PRINTF("Restore Done Interrupt seen\n");
-+ break;
-+ }
-+ dwc_udelay(10);
-+ } while (--timeout);
-+ if (!timeout) {
-+ DWC_PRINTF("Restore Done interrupt wasn't generated here\n");
-+ }
-+ }
-+ /* Clear all pending interupts */
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, 0xFFFFFFFF);
-+
-+ /* De-assert Restore */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.restore = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ dwc_udelay(10);
-+
-+ if (!rem_wakeup) {
-+ pcgcctl.d32 = 0;
-+ pcgcctl.b.rstpdwnmodule = 1;
-+ DWC_MODIFY_REG32(core_if->pcgcctl, pcgcctl.d32, 0);
-+ }
-+
-+ /* Restore GUSBCFG and DCFG */
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gusbcfg,
-+ core_if->gr_backup->gusbcfg_local);
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dcfg,
-+ core_if->dr_backup->dcfg);
-+
-+ /* De-assert Wakeup Logic */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuactv = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ dwc_udelay(10);
-+
-+ if (!rem_wakeup) {
-+ /* Set Device programming done bit */
-+ dctl.b.pwronprgdone = 1;
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl, 0, dctl.d32);
-+ } else {
-+ /* Start Remote Wakeup Signaling */
-+ dctl.d32 = core_if->dr_backup->dctl;
-+ dctl.b.rmtwkupsig = 1;
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dctl, dctl.d32);
-+ }
-+
-+ dwc_mdelay(2);
-+ /* Clear all pending interupts */
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, 0xFFFFFFFF);
-+
-+ /* Restore global registers */
-+ dwc_otg_restore_global_regs(core_if);
-+ /* Restore device global registers */
-+ dwc_otg_restore_dev_regs(core_if, rem_wakeup);
-+
-+ if (rem_wakeup) {
-+ dwc_mdelay(7);
-+ dctl.d32 = 0;
-+ dctl.b.rmtwkupsig = 1;
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl, dctl.d32, 0);
-+ }
-+
-+ core_if->hibernation_suspend = 0;
-+ /* The core will be in ON STATE */
-+ core_if->lx_state = DWC_OTG_L0;
-+ DWC_PRINTF("Hibernation recovery completes here\n");
-+
-+ return 1;
-+}
-+
-+/*
-+ * The restore operation is modified to support Synopsys Emulated Powerdown and
-+ * Hibernation. This function is for exiting from Host mode hibernation by
-+ * Host Initiated Resume/Reset and Device Initiated Remote-Wakeup.
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param rem_wakeup - indicates whether resume is initiated by Device or Host.
-+ * @param reset - indicates whether resume is initiated by Reset.
-+ */
-+int dwc_otg_host_hibernation_restore(dwc_otg_core_if_t * core_if,
-+ int rem_wakeup, int reset)
-+{
-+ gpwrdn_data_t gpwrdn = {.d32 = 0 };
-+ hprt0_data_t hprt0 = {.d32 = 0 };
-+
-+ int timeout = 2000;
-+
-+ DWC_DEBUGPL(DBG_HCD, "%s called\n", __FUNCTION__);
-+ /* Switch-on voltage to the core */
-+ gpwrdn.b.pwrdnswtch = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ dwc_udelay(10);
-+
-+ /* Reset core */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnrstn = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ dwc_udelay(10);
-+
-+ /* Assert Restore signal */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.restore = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32);
-+ dwc_udelay(10);
-+
-+ /* Disable power clamps */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnclmp = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+
-+ if (!rem_wakeup) {
-+ dwc_udelay(50);
-+ }
-+
-+ /* Deassert Reset core */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnrstn = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32);
-+ dwc_udelay(10);
-+
-+ /* Disable PMU interrupt */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuintsel = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.connect_det_msk = 1;
-+ gpwrdn.b.srp_det_msk = 1;
-+ gpwrdn.b.disconn_det_msk = 1;
-+ gpwrdn.b.rst_det_msk = 1;
-+ gpwrdn.b.lnstchng_msk = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+
-+ /* Indicates that we are going out from hibernation */
-+ core_if->hibernation_suspend = 0;
-+
-+ /* Set Restore Essential Regs bit in PCGCCTL register */
-+ restore_essential_regs(core_if, rem_wakeup, 1);
-+
-+ /* Wait a little for seeing new value of variable hibernation_suspend if
-+ * Restore done interrupt received before polling */
-+ dwc_udelay(10);
-+
-+ if (core_if->hibernation_suspend == 0) {
-+ /* Wait For Restore_done Interrupt. This mechanism of polling the
-+ * interrupt is introduced to avoid any possible race conditions
-+ */
-+ do {
-+ gintsts_data_t gintsts;
-+ gintsts.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintsts);
-+ if (gintsts.b.restoredone) {
-+ gintsts.d32 = 0;
-+ gintsts.b.restoredone = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32);
-+ DWC_DEBUGPL(DBG_HCD,"Restore Done Interrupt seen\n");
-+ break;
-+ }
-+ dwc_udelay(10);
-+ } while (--timeout);
-+ if (!timeout) {
-+ DWC_WARN("Restore Done interrupt wasn't generated\n");
-+ }
-+ }
-+
-+ /* Set the flag's value to 0 again after receiving restore done interrupt */
-+ core_if->hibernation_suspend = 0;
-+
-+ /* This step is not described in functional spec but if not wait for this
-+ * delay, mismatch interrupts occurred because just after restore core is
-+ * in Device mode(gintsts.curmode == 0) */
-+ dwc_mdelay(100);
-+
-+ /* Clear all pending interrupts */
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, 0xFFFFFFFF);
-+
-+ /* De-assert Restore */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.restore = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ dwc_udelay(10);
-+
-+ /* Restore GUSBCFG and HCFG */
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gusbcfg,
-+ core_if->gr_backup->gusbcfg_local);
-+ DWC_WRITE_REG32(&core_if->host_if->host_global_regs->hcfg,
-+ core_if->hr_backup->hcfg_local);
-+
-+ /* De-assert Wakeup Logic */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuactv = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ dwc_udelay(10);
-+
-+ /* Start the Resume operation by programming HPRT0 */
-+ hprt0.d32 = core_if->hr_backup->hprt0_local;
-+ hprt0.b.prtpwr = 1;
-+ hprt0.b.prtena = 0;
-+ hprt0.b.prtsusp = 0;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+
-+ DWC_PRINTF("Resume Starts Now\n");
-+ if (!reset) { // Indicates it is Resume Operation
-+ hprt0.d32 = core_if->hr_backup->hprt0_local;
-+ hprt0.b.prtres = 1;
-+ hprt0.b.prtpwr = 1;
-+ hprt0.b.prtena = 0;
-+ hprt0.b.prtsusp = 0;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+
-+ if (!rem_wakeup)
-+ hprt0.b.prtres = 0;
-+ /* Wait for Resume time and then program HPRT again */
-+ dwc_mdelay(100);
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+
-+ } else { // Indicates it is Reset Operation
-+ hprt0.d32 = core_if->hr_backup->hprt0_local;
-+ hprt0.b.prtrst = 1;
-+ hprt0.b.prtpwr = 1;
-+ hprt0.b.prtena = 0;
-+ hprt0.b.prtsusp = 0;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+ /* Wait for Reset time and then program HPRT again */
-+ dwc_mdelay(60);
-+ hprt0.b.prtrst = 0;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+ }
-+ /* Clear all interrupt status */
-+ hprt0.d32 = dwc_otg_read_hprt0(core_if);
-+ hprt0.b.prtconndet = 1;
-+ hprt0.b.prtenchng = 1;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+
-+ /* Clear all pending interupts */
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, 0xFFFFFFFF);
-+
-+ /* Restore global registers */
-+ dwc_otg_restore_global_regs(core_if);
-+ /* Restore host global registers */
-+ dwc_otg_restore_host_regs(core_if, reset);
-+
-+ /* The core will be in ON STATE */
-+ core_if->lx_state = DWC_OTG_L0;
-+ DWC_PRINTF("Hibernation recovery is complete here\n");
-+ return 0;
-+}
-+
-+/** Saves some register values into system memory. */
-+int dwc_otg_save_global_regs(dwc_otg_core_if_t * core_if)
-+{
-+ struct dwc_otg_global_regs_backup *gr;
-+ int i;
-+
-+ gr = core_if->gr_backup;
-+ if (!gr) {
-+ gr = DWC_ALLOC(sizeof(*gr));
-+ if (!gr) {
-+ return -DWC_E_NO_MEMORY;
-+ }
-+ core_if->gr_backup = gr;
-+ }
-+
-+ gr->gotgctl_local = DWC_READ_REG32(&core_if->core_global_regs->gotgctl);
-+ gr->gintmsk_local = DWC_READ_REG32(&core_if->core_global_regs->gintmsk);
-+ gr->gahbcfg_local = DWC_READ_REG32(&core_if->core_global_regs->gahbcfg);
-+ gr->gusbcfg_local = DWC_READ_REG32(&core_if->core_global_regs->gusbcfg);
-+ gr->grxfsiz_local = DWC_READ_REG32(&core_if->core_global_regs->grxfsiz);
-+ gr->gnptxfsiz_local = DWC_READ_REG32(&core_if->core_global_regs->gnptxfsiz);
-+ gr->hptxfsiz_local = DWC_READ_REG32(&core_if->core_global_regs->hptxfsiz);
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+ gr->glpmcfg_local = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg);
-+#endif
-+ gr->gi2cctl_local = DWC_READ_REG32(&core_if->core_global_regs->gi2cctl);
-+ gr->pcgcctl_local = DWC_READ_REG32(core_if->pcgcctl);
-+ gr->gdfifocfg_local =
-+ DWC_READ_REG32(&core_if->core_global_regs->gdfifocfg);
-+ for (i = 0; i < MAX_EPS_CHANNELS; i++) {
-+ gr->dtxfsiz_local[i] =
-+ DWC_READ_REG32(&(core_if->core_global_regs->dtxfsiz[i]));
-+ }
-+
-+ DWC_DEBUGPL(DBG_ANY, "===========Backing Global registers==========\n");
-+ DWC_DEBUGPL(DBG_ANY, "Backed up gotgctl = %08x\n", gr->gotgctl_local);
-+ DWC_DEBUGPL(DBG_ANY, "Backed up gintmsk = %08x\n", gr->gintmsk_local);
-+ DWC_DEBUGPL(DBG_ANY, "Backed up gahbcfg = %08x\n", gr->gahbcfg_local);
-+ DWC_DEBUGPL(DBG_ANY, "Backed up gusbcfg = %08x\n", gr->gusbcfg_local);
-+ DWC_DEBUGPL(DBG_ANY, "Backed up grxfsiz = %08x\n", gr->grxfsiz_local);
-+ DWC_DEBUGPL(DBG_ANY, "Backed up gnptxfsiz = %08x\n",
-+ gr->gnptxfsiz_local);
-+ DWC_DEBUGPL(DBG_ANY, "Backed up hptxfsiz = %08x\n",
-+ gr->hptxfsiz_local);
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+ DWC_DEBUGPL(DBG_ANY, "Backed up glpmcfg = %08x\n", gr->glpmcfg_local);
-+#endif
-+ DWC_DEBUGPL(DBG_ANY, "Backed up gi2cctl = %08x\n", gr->gi2cctl_local);
-+ DWC_DEBUGPL(DBG_ANY, "Backed up pcgcctl = %08x\n", gr->pcgcctl_local);
-+ DWC_DEBUGPL(DBG_ANY,"Backed up gdfifocfg = %08x\n",gr->gdfifocfg_local);
-+
-+ return 0;
-+}
-+
-+/** Saves GINTMSK register before setting the msk bits. */
-+int dwc_otg_save_gintmsk_reg(dwc_otg_core_if_t * core_if)
-+{
-+ struct dwc_otg_global_regs_backup *gr;
-+
-+ gr = core_if->gr_backup;
-+ if (!gr) {
-+ gr = DWC_ALLOC(sizeof(*gr));
-+ if (!gr) {
-+ return -DWC_E_NO_MEMORY;
-+ }
-+ core_if->gr_backup = gr;
-+ }
-+
-+ gr->gintmsk_local = DWC_READ_REG32(&core_if->core_global_regs->gintmsk);
-+
-+ DWC_DEBUGPL(DBG_ANY,"=============Backing GINTMSK registers============\n");
-+ DWC_DEBUGPL(DBG_ANY, "Backed up gintmsk = %08x\n", gr->gintmsk_local);
-+
-+ return 0;
-+}
-+
-+int dwc_otg_save_dev_regs(dwc_otg_core_if_t * core_if)
-+{
-+ struct dwc_otg_dev_regs_backup *dr;
-+ int i;
-+
-+ dr = core_if->dr_backup;
-+ if (!dr) {
-+ dr = DWC_ALLOC(sizeof(*dr));
-+ if (!dr) {
-+ return -DWC_E_NO_MEMORY;
-+ }
-+ core_if->dr_backup = dr;
-+ }
-+
-+ dr->dcfg = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dcfg);
-+ dr->dctl = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dctl);
-+ dr->daintmsk =
-+ DWC_READ_REG32(&core_if->dev_if->dev_global_regs->daintmsk);
-+ dr->diepmsk =
-+ DWC_READ_REG32(&core_if->dev_if->dev_global_regs->diepmsk);
-+ dr->doepmsk =
-+ DWC_READ_REG32(&core_if->dev_if->dev_global_regs->doepmsk);
-+
-+ for (i = 0; i < core_if->dev_if->num_in_eps; ++i) {
-+ dr->diepctl[i] =
-+ DWC_READ_REG32(&core_if->dev_if->in_ep_regs[i]->diepctl);
-+ dr->dieptsiz[i] =
-+ DWC_READ_REG32(&core_if->dev_if->in_ep_regs[i]->dieptsiz);
-+ dr->diepdma[i] =
-+ DWC_READ_REG32(&core_if->dev_if->in_ep_regs[i]->diepdma);
-+ }
-+
-+ DWC_DEBUGPL(DBG_ANY,
-+ "=============Backing Host registers==============\n");
-+ DWC_DEBUGPL(DBG_ANY, "Backed up dcfg = %08x\n", dr->dcfg);
-+ DWC_DEBUGPL(DBG_ANY, "Backed up dctl = %08x\n", dr->dctl);
-+ DWC_DEBUGPL(DBG_ANY, "Backed up daintmsk = %08x\n",
-+ dr->daintmsk);
-+ DWC_DEBUGPL(DBG_ANY, "Backed up diepmsk = %08x\n", dr->diepmsk);
-+ DWC_DEBUGPL(DBG_ANY, "Backed up doepmsk = %08x\n", dr->doepmsk);
-+ for (i = 0; i < core_if->dev_if->num_in_eps; ++i) {
-+ DWC_DEBUGPL(DBG_ANY, "Backed up diepctl[%d] = %08x\n", i,
-+ dr->diepctl[i]);
-+ DWC_DEBUGPL(DBG_ANY, "Backed up dieptsiz[%d] = %08x\n",
-+ i, dr->dieptsiz[i]);
-+ DWC_DEBUGPL(DBG_ANY, "Backed up diepdma[%d] = %08x\n", i,
-+ dr->diepdma[i]);
-+ }
-+
-+ return 0;
-+}
-+
-+int dwc_otg_save_host_regs(dwc_otg_core_if_t * core_if)
-+{
-+ struct dwc_otg_host_regs_backup *hr;
-+ int i;
-+
-+ hr = core_if->hr_backup;
-+ if (!hr) {
-+ hr = DWC_ALLOC(sizeof(*hr));
-+ if (!hr) {
-+ return -DWC_E_NO_MEMORY;
-+ }
-+ core_if->hr_backup = hr;
-+ }
-+
-+ hr->hcfg_local =
-+ DWC_READ_REG32(&core_if->host_if->host_global_regs->hcfg);
-+ hr->haintmsk_local =
-+ DWC_READ_REG32(&core_if->host_if->host_global_regs->haintmsk);
-+ for (i = 0; i < dwc_otg_get_param_host_channels(core_if); ++i) {
-+ hr->hcintmsk_local[i] =
-+ DWC_READ_REG32(&core_if->host_if->hc_regs[i]->hcintmsk);
-+ }
-+ hr->hprt0_local = DWC_READ_REG32(core_if->host_if->hprt0);
-+ hr->hfir_local =
-+ DWC_READ_REG32(&core_if->host_if->host_global_regs->hfir);
-+
-+ DWC_DEBUGPL(DBG_ANY,
-+ "=============Backing Host registers===============\n");
-+ DWC_DEBUGPL(DBG_ANY, "Backed up hcfg = %08x\n",
-+ hr->hcfg_local);
-+ DWC_DEBUGPL(DBG_ANY, "Backed up haintmsk = %08x\n", hr->haintmsk_local);
-+ for (i = 0; i < dwc_otg_get_param_host_channels(core_if); ++i) {
-+ DWC_DEBUGPL(DBG_ANY, "Backed up hcintmsk[%02d]=%08x\n", i,
-+ hr->hcintmsk_local[i]);
-+ }
-+ DWC_DEBUGPL(DBG_ANY, "Backed up hprt0 = %08x\n",
-+ hr->hprt0_local);
-+ DWC_DEBUGPL(DBG_ANY, "Backed up hfir = %08x\n",
-+ hr->hfir_local);
-+
-+ return 0;
-+}
-+
-+int dwc_otg_restore_global_regs(dwc_otg_core_if_t *core_if)
-+{
-+ struct dwc_otg_global_regs_backup *gr;
-+ int i;
-+
-+ gr = core_if->gr_backup;
-+ if (!gr) {
-+ return -DWC_E_INVALID;
-+ }
-+
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gotgctl, gr->gotgctl_local);
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintmsk, gr->gintmsk_local);
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gusbcfg, gr->gusbcfg_local);
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gahbcfg, gr->gahbcfg_local);
-+ DWC_WRITE_REG32(&core_if->core_global_regs->grxfsiz, gr->grxfsiz_local);
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gnptxfsiz,
-+ gr->gnptxfsiz_local);
-+ DWC_WRITE_REG32(&core_if->core_global_regs->hptxfsiz,
-+ gr->hptxfsiz_local);
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gdfifocfg,
-+ gr->gdfifocfg_local);
-+ for (i = 0; i < MAX_EPS_CHANNELS; i++) {
-+ DWC_WRITE_REG32(&core_if->core_global_regs->dtxfsiz[i],
-+ gr->dtxfsiz_local[i]);
-+ }
-+
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, 0xFFFFFFFF);
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, 0x0000100A);
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gahbcfg,
-+ (gr->gahbcfg_local));
-+ return 0;
-+}
-+
-+int dwc_otg_restore_dev_regs(dwc_otg_core_if_t * core_if, int rem_wakeup)
-+{
-+ struct dwc_otg_dev_regs_backup *dr;
-+ int i;
-+
-+ dr = core_if->dr_backup;
-+
-+ if (!dr) {
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if (!rem_wakeup) {
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dctl,
-+ dr->dctl);
-+ }
-+
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->daintmsk, dr->daintmsk);
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->diepmsk, dr->diepmsk);
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->doepmsk, dr->doepmsk);
-+
-+ for (i = 0; i < core_if->dev_if->num_in_eps; ++i) {
-+ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[i]->dieptsiz, dr->dieptsiz[i]);
-+ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[i]->diepdma, dr->diepdma[i]);
-+ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[i]->diepctl, dr->diepctl[i]);
-+ }
-+
-+ return 0;
-+}
-+
-+int dwc_otg_restore_host_regs(dwc_otg_core_if_t * core_if, int reset)
-+{
-+ struct dwc_otg_host_regs_backup *hr;
-+ int i;
-+ hr = core_if->hr_backup;
-+
-+ if (!hr) {
-+ return -DWC_E_INVALID;
-+ }
-+
-+ DWC_WRITE_REG32(&core_if->host_if->host_global_regs->hcfg, hr->hcfg_local);
-+ //if (!reset)
-+ //{
-+ // DWC_WRITE_REG32(&core_if->host_if->host_global_regs->hfir, hr->hfir_local);
-+ //}
-+
-+ DWC_WRITE_REG32(&core_if->host_if->host_global_regs->haintmsk,
-+ hr->haintmsk_local);
-+ for (i = 0; i < dwc_otg_get_param_host_channels(core_if); ++i) {
-+ DWC_WRITE_REG32(&core_if->host_if->hc_regs[i]->hcintmsk,
-+ hr->hcintmsk_local[i]);
-+ }
-+
-+ return 0;
-+}
-+
-+int restore_lpm_i2c_regs(dwc_otg_core_if_t * core_if)
-+{
-+ struct dwc_otg_global_regs_backup *gr;
-+
-+ gr = core_if->gr_backup;
-+
-+ /* Restore values for LPM and I2C */
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+ DWC_WRITE_REG32(&core_if->core_global_regs->glpmcfg, gr->glpmcfg_local);
-+#endif
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gi2cctl, gr->gi2cctl_local);
-+
-+ return 0;
-+}
-+
-+int restore_essential_regs(dwc_otg_core_if_t * core_if, int rmode, int is_host)
-+{
-+ struct dwc_otg_global_regs_backup *gr;
-+ pcgcctl_data_t pcgcctl = {.d32 = 0 };
-+ gahbcfg_data_t gahbcfg = {.d32 = 0 };
-+ gusbcfg_data_t gusbcfg = {.d32 = 0 };
-+ gintmsk_data_t gintmsk = {.d32 = 0 };
-+
-+ /* Restore LPM and I2C registers */
-+ restore_lpm_i2c_regs(core_if);
-+
-+ /* Set PCGCCTL to 0 */
-+ DWC_WRITE_REG32(core_if->pcgcctl, 0x00000000);
-+
-+ gr = core_if->gr_backup;
-+ /* Load restore values for [31:14] bits */
-+ DWC_WRITE_REG32(core_if->pcgcctl,
-+ ((gr->pcgcctl_local & 0xffffc000) | 0x00020000));
-+
-+ /* Umnask global Interrupt in GAHBCFG and restore it */
-+ gahbcfg.d32 = gr->gahbcfg_local;
-+ gahbcfg.b.glblintrmsk = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gahbcfg, gahbcfg.d32);
-+
-+ /* Clear all pending interupts */
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, 0xFFFFFFFF);
-+
-+ /* Unmask restore done interrupt */
-+ gintmsk.b.restoredone = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintmsk, gintmsk.d32);
-+
-+ /* Restore GUSBCFG and HCFG/DCFG */
-+ gusbcfg.d32 = core_if->gr_backup->gusbcfg_local;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gusbcfg, gusbcfg.d32);
-+
-+ if (is_host) {
-+ hcfg_data_t hcfg = {.d32 = 0 };
-+ hcfg.d32 = core_if->hr_backup->hcfg_local;
-+ DWC_WRITE_REG32(&core_if->host_if->host_global_regs->hcfg,
-+ hcfg.d32);
-+
-+ /* Load restore values for [31:14] bits */
-+ pcgcctl.d32 = gr->pcgcctl_local & 0xffffc000;
-+ pcgcctl.d32 = gr->pcgcctl_local | 0x00020000;
-+
-+ if (rmode)
-+ pcgcctl.b.restoremode = 1;
-+ DWC_WRITE_REG32(core_if->pcgcctl, pcgcctl.d32);
-+ dwc_udelay(10);
-+
-+ /* Load restore values for [31:14] bits and set EssRegRestored bit */
-+ pcgcctl.d32 = gr->pcgcctl_local | 0xffffc000;
-+ pcgcctl.d32 = gr->pcgcctl_local & 0xffffc000;
-+ pcgcctl.b.ess_reg_restored = 1;
-+ if (rmode)
-+ pcgcctl.b.restoremode = 1;
-+ DWC_WRITE_REG32(core_if->pcgcctl, pcgcctl.d32);
-+ } else {
-+ dcfg_data_t dcfg = {.d32 = 0 };
-+ dcfg.d32 = core_if->dr_backup->dcfg;
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dcfg, dcfg.d32);
-+
-+ /* Load restore values for [31:14] bits */
-+ pcgcctl.d32 = gr->pcgcctl_local & 0xffffc000;
-+ pcgcctl.d32 = gr->pcgcctl_local | 0x00020000;
-+ if (!rmode) {
-+ pcgcctl.d32 |= 0x208;
-+ }
-+ DWC_WRITE_REG32(core_if->pcgcctl, pcgcctl.d32);
-+ dwc_udelay(10);
-+
-+ /* Load restore values for [31:14] bits */
-+ pcgcctl.d32 = gr->pcgcctl_local & 0xffffc000;
-+ pcgcctl.d32 = gr->pcgcctl_local | 0x00020000;
-+ pcgcctl.b.ess_reg_restored = 1;
-+ if (!rmode)
-+ pcgcctl.d32 |= 0x208;
-+ DWC_WRITE_REG32(core_if->pcgcctl, pcgcctl.d32);
-+ }
-+
-+ return 0;
-+}
-+
-+/**
-+ * Initializes the FSLSPClkSel field of the HCFG register depending on the PHY
-+ * type.
-+ */
-+static void init_fslspclksel(dwc_otg_core_if_t * core_if)
-+{
-+ uint32_t val;
-+ hcfg_data_t hcfg;
-+
-+ if (((core_if->hwcfg2.b.hs_phy_type == 2) &&
-+ (core_if->hwcfg2.b.fs_phy_type == 1) &&
-+ (core_if->core_params->ulpi_fs_ls)) ||
-+ (core_if->core_params->phy_type == DWC_PHY_TYPE_PARAM_FS)) {
-+ /* Full speed PHY */
-+ val = DWC_HCFG_48_MHZ;
-+ } else {
-+ /* High speed PHY running at full speed or high speed */
-+ val = DWC_HCFG_30_60_MHZ;
-+ }
-+
-+ DWC_DEBUGPL(DBG_CIL, "Initializing HCFG.FSLSPClkSel to 0x%1x\n", val);
-+ hcfg.d32 = DWC_READ_REG32(&core_if->host_if->host_global_regs->hcfg);
-+ hcfg.b.fslspclksel = val;
-+ DWC_WRITE_REG32(&core_if->host_if->host_global_regs->hcfg, hcfg.d32);
-+}
-+
-+/**
-+ * Initializes the DevSpd field of the DCFG register depending on the PHY type
-+ * and the enumeration speed of the device.
-+ */
-+static void init_devspd(dwc_otg_core_if_t * core_if)
-+{
-+ uint32_t val;
-+ dcfg_data_t dcfg;
-+
-+ if (((core_if->hwcfg2.b.hs_phy_type == 2) &&
-+ (core_if->hwcfg2.b.fs_phy_type == 1) &&
-+ (core_if->core_params->ulpi_fs_ls)) ||
-+ (core_if->core_params->phy_type == DWC_PHY_TYPE_PARAM_FS)) {
-+ /* Full speed PHY */
-+ val = 0x3;
-+ } else if (core_if->core_params->speed == DWC_SPEED_PARAM_FULL) {
-+ /* High speed PHY running at full speed */
-+ val = 0x1;
-+ } else {
-+ /* High speed PHY running at high speed */
-+ val = 0x0;
-+ }
-+
-+ DWC_DEBUGPL(DBG_CIL, "Initializing DCFG.DevSpd to 0x%1x\n", val);
-+
-+ dcfg.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dcfg);
-+ dcfg.b.devspd = val;
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dcfg, dcfg.d32);
-+}
-+
-+/**
-+ * This function calculates the number of IN EPS
-+ * using GHWCFG1 and GHWCFG2 registers values
-+ *
-+ * @param core_if Programming view of the DWC_otg controller
-+ */
-+static uint32_t calc_num_in_eps(dwc_otg_core_if_t * core_if)
-+{
-+ uint32_t num_in_eps = 0;
-+ uint32_t num_eps = core_if->hwcfg2.b.num_dev_ep;
-+ uint32_t hwcfg1 = core_if->hwcfg1.d32 >> 3;
-+ uint32_t num_tx_fifos = core_if->hwcfg4.b.num_in_eps;
-+ int i;
-+
-+ for (i = 0; i < num_eps; ++i) {
-+ if (!(hwcfg1 & 0x1))
-+ num_in_eps++;
-+
-+ hwcfg1 >>= 2;
-+ }
-+
-+ if (core_if->hwcfg4.b.ded_fifo_en) {
-+ num_in_eps =
-+ (num_in_eps > num_tx_fifos) ? num_tx_fifos : num_in_eps;
-+ }
-+
-+ return num_in_eps;
-+}
-+
-+/**
-+ * This function calculates the number of OUT EPS
-+ * using GHWCFG1 and GHWCFG2 registers values
-+ *
-+ * @param core_if Programming view of the DWC_otg controller
-+ */
-+static uint32_t calc_num_out_eps(dwc_otg_core_if_t * core_if)
-+{
-+ uint32_t num_out_eps = 0;
-+ uint32_t num_eps = core_if->hwcfg2.b.num_dev_ep;
-+ uint32_t hwcfg1 = core_if->hwcfg1.d32 >> 2;
-+ int i;
-+
-+ for (i = 0; i < num_eps; ++i) {
-+ if (!(hwcfg1 & 0x1))
-+ num_out_eps++;
-+
-+ hwcfg1 >>= 2;
-+ }
-+ return num_out_eps;
-+}
-+
-+/**
-+ * This function initializes the DWC_otg controller registers and
-+ * prepares the core for device mode or host mode operation.
-+ *
-+ * @param core_if Programming view of the DWC_otg controller
-+ *
-+ */
-+void dwc_otg_core_init(dwc_otg_core_if_t * core_if)
-+{
-+ int i = 0;
-+ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs;
-+ dwc_otg_dev_if_t *dev_if = core_if->dev_if;
-+ gahbcfg_data_t ahbcfg = {.d32 = 0 };
-+ gusbcfg_data_t usbcfg = {.d32 = 0 };
-+ gi2cctl_data_t i2cctl = {.d32 = 0 };
-+
-+ DWC_DEBUGPL(DBG_CILV, "dwc_otg_core_init(%p) regs at %p\n",
-+ core_if, global_regs);
-+
-+ /* Common Initialization */
-+ usbcfg.d32 = DWC_READ_REG32(&global_regs->gusbcfg);
-+
-+ /* Program the ULPI External VBUS bit if needed */
-+ usbcfg.b.ulpi_ext_vbus_drv =
-+ (core_if->core_params->phy_ulpi_ext_vbus ==
-+ DWC_PHY_ULPI_EXTERNAL_VBUS) ? 1 : 0;
-+
-+ /* Set external TS Dline pulsing */
-+ usbcfg.b.term_sel_dl_pulse =
-+ (core_if->core_params->ts_dline == 1) ? 1 : 0;
-+ DWC_WRITE_REG32(&global_regs->gusbcfg, usbcfg.d32);
-+
-+ /* Reset the Controller */
-+ dwc_otg_core_reset(core_if);
-+
-+ core_if->adp_enable = core_if->core_params->adp_supp_enable;
-+ core_if->power_down = core_if->core_params->power_down;
-+ core_if->otg_sts = 0;
-+
-+ /* Initialize parameters from Hardware configuration registers. */
-+ dev_if->num_in_eps = calc_num_in_eps(core_if);
-+ dev_if->num_out_eps = calc_num_out_eps(core_if);
-+
-+ DWC_DEBUGPL(DBG_CIL, "num_dev_perio_in_ep=%d\n",
-+ core_if->hwcfg4.b.num_dev_perio_in_ep);
-+
-+ for (i = 0; i < core_if->hwcfg4.b.num_dev_perio_in_ep; i++) {
-+ dev_if->perio_tx_fifo_size[i] =
-+ DWC_READ_REG32(&global_regs->dtxfsiz[i]) >> 16;
-+ DWC_DEBUGPL(DBG_CIL, "Periodic Tx FIFO SZ #%d=0x%0x\n",
-+ i, dev_if->perio_tx_fifo_size[i]);
-+ }
-+
-+ for (i = 0; i < core_if->hwcfg4.b.num_in_eps; i++) {
-+ dev_if->tx_fifo_size[i] =
-+ DWC_READ_REG32(&global_regs->dtxfsiz[i]) >> 16;
-+ DWC_DEBUGPL(DBG_CIL, "Tx FIFO SZ #%d=0x%0x\n",
-+ i, dev_if->tx_fifo_size[i]);
-+ }
-+
-+ core_if->total_fifo_size = core_if->hwcfg3.b.dfifo_depth;
-+ core_if->rx_fifo_size = DWC_READ_REG32(&global_regs->grxfsiz);
-+ core_if->nperio_tx_fifo_size =
-+ DWC_READ_REG32(&global_regs->gnptxfsiz) >> 16;
-+
-+ DWC_DEBUGPL(DBG_CIL, "Total FIFO SZ=%d\n", core_if->total_fifo_size);
-+ DWC_DEBUGPL(DBG_CIL, "Rx FIFO SZ=%d\n", core_if->rx_fifo_size);
-+ DWC_DEBUGPL(DBG_CIL, "NP Tx FIFO SZ=%d\n",
-+ core_if->nperio_tx_fifo_size);
-+
-+ /* This programming sequence needs to happen in FS mode before any other
-+ * programming occurs */
-+ if ((core_if->core_params->speed == DWC_SPEED_PARAM_FULL) &&
-+ (core_if->core_params->phy_type == DWC_PHY_TYPE_PARAM_FS)) {
-+ /* If FS mode with FS PHY */
-+
-+ /* core_init() is now called on every switch so only call the
-+ * following for the first time through. */
-+ if (!core_if->phy_init_done) {
-+ core_if->phy_init_done = 1;
-+ DWC_DEBUGPL(DBG_CIL, "FS_PHY detected\n");
-+ usbcfg.d32 = DWC_READ_REG32(&global_regs->gusbcfg);
-+ usbcfg.b.physel = 1;
-+ DWC_WRITE_REG32(&global_regs->gusbcfg, usbcfg.d32);
-+
-+ /* Reset after a PHY select */
-+ dwc_otg_core_reset(core_if);
-+ }
-+
-+ /* Program DCFG.DevSpd or HCFG.FSLSPclkSel to 48Mhz in FS. Also
-+ * do this on HNP Dev/Host mode switches (done in dev_init and
-+ * host_init). */
-+ if (dwc_otg_is_host_mode(core_if)) {
-+ init_fslspclksel(core_if);
-+ } else {
-+ init_devspd(core_if);
-+ }
-+
-+ if (core_if->core_params->i2c_enable) {
-+ DWC_DEBUGPL(DBG_CIL, "FS_PHY Enabling I2c\n");
-+ /* Program GUSBCFG.OtgUtmifsSel to I2C */
-+ usbcfg.d32 = DWC_READ_REG32(&global_regs->gusbcfg);
-+ usbcfg.b.otgutmifssel = 1;
-+ DWC_WRITE_REG32(&global_regs->gusbcfg, usbcfg.d32);
-+
-+ /* Program GI2CCTL.I2CEn */
-+ i2cctl.d32 = DWC_READ_REG32(&global_regs->gi2cctl);
-+ i2cctl.b.i2cdevaddr = 1;
-+ i2cctl.b.i2cen = 0;
-+ DWC_WRITE_REG32(&global_regs->gi2cctl, i2cctl.d32);
-+ i2cctl.b.i2cen = 1;
-+ DWC_WRITE_REG32(&global_regs->gi2cctl, i2cctl.d32);
-+ }
-+
-+ } /* endif speed == DWC_SPEED_PARAM_FULL */
-+ else {
-+ /* High speed PHY. */
-+ if (!core_if->phy_init_done) {
-+ core_if->phy_init_done = 1;
-+ /* HS PHY parameters. These parameters are preserved
-+ * during soft reset so only program the first time. Do
-+ * a soft reset immediately after setting phyif. */
-+
-+ if (core_if->core_params->phy_type == 2) {
-+ /* ULPI interface */
-+ usbcfg.b.ulpi_utmi_sel = 1;
-+ usbcfg.b.phyif = 0;
-+ usbcfg.b.ddrsel =
-+ core_if->core_params->phy_ulpi_ddr;
-+ } else if (core_if->core_params->phy_type == 1) {
-+ /* UTMI+ interface */
-+ usbcfg.b.ulpi_utmi_sel = 0;
-+ if (core_if->core_params->phy_utmi_width == 16) {
-+ usbcfg.b.phyif = 1;
-+
-+ } else {
-+ usbcfg.b.phyif = 0;
-+ }
-+ } else {
-+ DWC_ERROR("FS PHY TYPE\n");
-+ }
-+ DWC_WRITE_REG32(&global_regs->gusbcfg, usbcfg.d32);
-+ /* Reset after setting the PHY parameters */
-+ dwc_otg_core_reset(core_if);
-+ }
-+ }
-+
-+ if ((core_if->hwcfg2.b.hs_phy_type == 2) &&
-+ (core_if->hwcfg2.b.fs_phy_type == 1) &&
-+ (core_if->core_params->ulpi_fs_ls)) {
-+ DWC_DEBUGPL(DBG_CIL, "Setting ULPI FSLS\n");
-+ usbcfg.d32 = DWC_READ_REG32(&global_regs->gusbcfg);
-+ usbcfg.b.ulpi_fsls = 1;
-+ usbcfg.b.ulpi_clk_sus_m = 1;
-+ DWC_WRITE_REG32(&global_regs->gusbcfg, usbcfg.d32);
-+ } else {
-+ usbcfg.d32 = DWC_READ_REG32(&global_regs->gusbcfg);
-+ usbcfg.b.ulpi_fsls = 0;
-+ usbcfg.b.ulpi_clk_sus_m = 0;
-+ DWC_WRITE_REG32(&global_regs->gusbcfg, usbcfg.d32);
-+ }
-+
-+ /* Program the GAHBCFG Register. */
-+ switch (core_if->hwcfg2.b.architecture) {
-+
-+ case DWC_SLAVE_ONLY_ARCH:
-+ DWC_DEBUGPL(DBG_CIL, "Slave Only Mode\n");
-+ ahbcfg.b.nptxfemplvl_txfemplvl =
-+ DWC_GAHBCFG_TXFEMPTYLVL_HALFEMPTY;
-+ ahbcfg.b.ptxfemplvl = DWC_GAHBCFG_TXFEMPTYLVL_HALFEMPTY;
-+ core_if->dma_enable = 0;
-+ core_if->dma_desc_enable = 0;
-+ break;
-+
-+ case DWC_EXT_DMA_ARCH:
-+ DWC_DEBUGPL(DBG_CIL, "External DMA Mode\n");
-+ {
-+ uint8_t brst_sz = core_if->core_params->dma_burst_size;
-+ ahbcfg.b.hburstlen = 0;
-+ while (brst_sz > 1) {
-+ ahbcfg.b.hburstlen++;
-+ brst_sz >>= 1;
-+ }
-+ }
-+ core_if->dma_enable = (core_if->core_params->dma_enable != 0);
-+ core_if->dma_desc_enable =
-+ (core_if->core_params->dma_desc_enable != 0);
-+ break;
-+
-+ case DWC_INT_DMA_ARCH:
-+ DWC_DEBUGPL(DBG_CIL, "Internal DMA Mode\n");
-+ /* Old value was DWC_GAHBCFG_INT_DMA_BURST_INCR - done for
-+ Host mode ISOC in issue fix - vahrama */
-+ /* Broadcom had altered to (1<<3)|(0<<0) - WRESP=1, max 4 beats */
-+ ahbcfg.b.hburstlen = (1<<3)|(0<<0);//DWC_GAHBCFG_INT_DMA_BURST_INCR4;
-+ core_if->dma_enable = (core_if->core_params->dma_enable != 0);
-+ core_if->dma_desc_enable =
-+ (core_if->core_params->dma_desc_enable != 0);
-+ break;
-+
-+ }
-+ if (core_if->dma_enable) {
-+ if (core_if->dma_desc_enable) {
-+ DWC_PRINTF("Using Descriptor DMA mode\n");
-+ } else {
-+ DWC_PRINTF("Using Buffer DMA mode\n");
-+
-+ }
-+ } else {
-+ DWC_PRINTF("Using Slave mode\n");
-+ core_if->dma_desc_enable = 0;
-+ }
-+
-+ if (core_if->core_params->ahb_single) {
-+ ahbcfg.b.ahbsingle = 1;
-+ }
-+
-+ ahbcfg.b.dmaenable = core_if->dma_enable;
-+ DWC_WRITE_REG32(&global_regs->gahbcfg, ahbcfg.d32);
-+
-+ core_if->en_multiple_tx_fifo = core_if->hwcfg4.b.ded_fifo_en;
-+
-+ core_if->pti_enh_enable = core_if->core_params->pti_enable != 0;
-+ core_if->multiproc_int_enable = core_if->core_params->mpi_enable;
-+ DWC_PRINTF("Periodic Transfer Interrupt Enhancement - %s\n",
-+ ((core_if->pti_enh_enable) ? "enabled" : "disabled"));
-+ DWC_PRINTF("Multiprocessor Interrupt Enhancement - %s\n",
-+ ((core_if->multiproc_int_enable) ? "enabled" : "disabled"));
-+
-+ /*
-+ * Program the GUSBCFG register.
-+ */
-+ usbcfg.d32 = DWC_READ_REG32(&global_regs->gusbcfg);
-+
-+ switch (core_if->hwcfg2.b.op_mode) {
-+ case DWC_MODE_HNP_SRP_CAPABLE:
-+ usbcfg.b.hnpcap = (core_if->core_params->otg_cap ==
-+ DWC_OTG_CAP_PARAM_HNP_SRP_CAPABLE);
-+ usbcfg.b.srpcap = (core_if->core_params->otg_cap !=
-+ DWC_OTG_CAP_PARAM_NO_HNP_SRP_CAPABLE);
-+ break;
-+
-+ case DWC_MODE_SRP_ONLY_CAPABLE:
-+ usbcfg.b.hnpcap = 0;
-+ usbcfg.b.srpcap = (core_if->core_params->otg_cap !=
-+ DWC_OTG_CAP_PARAM_NO_HNP_SRP_CAPABLE);
-+ break;
-+
-+ case DWC_MODE_NO_HNP_SRP_CAPABLE:
-+ usbcfg.b.hnpcap = 0;
-+ usbcfg.b.srpcap = 0;
-+ break;
-+
-+ case DWC_MODE_SRP_CAPABLE_DEVICE:
-+ usbcfg.b.hnpcap = 0;
-+ usbcfg.b.srpcap = (core_if->core_params->otg_cap !=
-+ DWC_OTG_CAP_PARAM_NO_HNP_SRP_CAPABLE);
-+ break;
-+
-+ case DWC_MODE_NO_SRP_CAPABLE_DEVICE:
-+ usbcfg.b.hnpcap = 0;
-+ usbcfg.b.srpcap = 0;
-+ break;
-+
-+ case DWC_MODE_SRP_CAPABLE_HOST:
-+ usbcfg.b.hnpcap = 0;
-+ usbcfg.b.srpcap = (core_if->core_params->otg_cap !=
-+ DWC_OTG_CAP_PARAM_NO_HNP_SRP_CAPABLE);
-+ break;
-+
-+ case DWC_MODE_NO_SRP_CAPABLE_HOST:
-+ usbcfg.b.hnpcap = 0;
-+ usbcfg.b.srpcap = 0;
-+ break;
-+ }
-+
-+ DWC_WRITE_REG32(&global_regs->gusbcfg, usbcfg.d32);
-+
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+ if (core_if->core_params->lpm_enable) {
-+ glpmcfg_data_t lpmcfg = {.d32 = 0 };
-+
-+ /* To enable LPM support set lpm_cap_en bit */
-+ lpmcfg.b.lpm_cap_en = 1;
-+
-+ /* Make AppL1Res ACK */
-+ lpmcfg.b.appl_resp = 1;
-+
-+ /* Retry 3 times */
-+ lpmcfg.b.retry_count = 3;
-+
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->glpmcfg,
-+ 0, lpmcfg.d32);
-+
-+ }
-+#endif
-+ if (core_if->core_params->ic_usb_cap) {
-+ gusbcfg_data_t gusbcfg = {.d32 = 0 };
-+ gusbcfg.b.ic_usb_cap = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gusbcfg,
-+ 0, gusbcfg.d32);
-+ }
-+ {
-+ gotgctl_data_t gotgctl = {.d32 = 0 };
-+ gotgctl.b.otgver = core_if->core_params->otg_ver;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gotgctl, 0,
-+ gotgctl.d32);
-+ /* Set OTG version supported */
-+ core_if->otg_ver = core_if->core_params->otg_ver;
-+ DWC_PRINTF("OTG VER PARAM: %d, OTG VER FLAG: %d\n",
-+ core_if->core_params->otg_ver, core_if->otg_ver);
-+ }
-+
-+
-+ /* Enable common interrupts */
-+ dwc_otg_enable_common_interrupts(core_if);
-+
-+ /* Do device or host intialization based on mode during PCD
-+ * and HCD initialization */
-+ if (dwc_otg_is_host_mode(core_if)) {
-+ DWC_DEBUGPL(DBG_ANY, "Host Mode\n");
-+ core_if->op_state = A_HOST;
-+ } else {
-+ DWC_DEBUGPL(DBG_ANY, "Device Mode\n");
-+ core_if->op_state = B_PERIPHERAL;
-+#ifdef DWC_DEVICE_ONLY
-+ dwc_otg_core_dev_init(core_if);
-+#endif
-+ }
-+}
-+
-+/**
-+ * This function enables the Device mode interrupts.
-+ *
-+ * @param core_if Programming view of DWC_otg controller
-+ */
-+void dwc_otg_enable_device_interrupts(dwc_otg_core_if_t * core_if)
-+{
-+ gintmsk_data_t intr_mask = {.d32 = 0 };
-+ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs;
-+
-+ DWC_DEBUGPL(DBG_CIL, "%s()\n", __func__);
-+
-+ /* Disable all interrupts. */
-+ DWC_WRITE_REG32(&global_regs->gintmsk, 0);
-+
-+ /* Clear any pending interrupts */
-+ DWC_WRITE_REG32(&global_regs->gintsts, 0xFFFFFFFF);
-+
-+ /* Enable the common interrupts */
-+ dwc_otg_enable_common_interrupts(core_if);
-+
-+ /* Enable interrupts */
-+ intr_mask.b.usbreset = 1;
-+ intr_mask.b.enumdone = 1;
-+ /* Disable Disconnect interrupt in Device mode */
-+ intr_mask.b.disconnect = 0;
-+
-+ if (!core_if->multiproc_int_enable) {
-+ intr_mask.b.inepintr = 1;
-+ intr_mask.b.outepintr = 1;
-+ }
-+
-+ intr_mask.b.erlysuspend = 1;
-+
-+ if (core_if->en_multiple_tx_fifo == 0) {
-+ intr_mask.b.epmismatch = 1;
-+ }
-+
-+ //intr_mask.b.incomplisoout = 1;
-+ intr_mask.b.incomplisoin = 1;
-+
-+/* Enable the ignore frame number for ISOC xfers - MAS */
-+/* Disable to support high bandwith ISOC transfers - manukz */
-+#if 0
-+#ifdef DWC_UTE_PER_IO
-+ if (core_if->dma_enable) {
-+ if (core_if->dma_desc_enable) {
-+ dctl_data_t dctl1 = {.d32 = 0 };
-+ dctl1.b.ifrmnum = 1;
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->
-+ dctl, 0, dctl1.d32);
-+ DWC_DEBUG("----Enabled Ignore frame number (0x%08x)",
-+ DWC_READ_REG32(&core_if->dev_if->
-+ dev_global_regs->dctl));
-+ }
-+ }
-+#endif
-+#endif
-+#ifdef DWC_EN_ISOC
-+ if (core_if->dma_enable) {
-+ if (core_if->dma_desc_enable == 0) {
-+ if (core_if->pti_enh_enable) {
-+ dctl_data_t dctl = {.d32 = 0 };
-+ dctl.b.ifrmnum = 1;
-+ DWC_MODIFY_REG32(&core_if->
-+ dev_if->dev_global_regs->dctl,
-+ 0, dctl.d32);
-+ } else {
-+ intr_mask.b.incomplisoin = 1;
-+ intr_mask.b.incomplisoout = 1;
-+ }
-+ }
-+ } else {
-+ intr_mask.b.incomplisoin = 1;
-+ intr_mask.b.incomplisoout = 1;
-+ }
-+#endif /* DWC_EN_ISOC */
-+
-+ /** @todo NGS: Should this be a module parameter? */
-+#ifdef USE_PERIODIC_EP
-+ intr_mask.b.isooutdrop = 1;
-+ intr_mask.b.eopframe = 1;
-+ intr_mask.b.incomplisoin = 1;
-+ intr_mask.b.incomplisoout = 1;
-+#endif
-+
-+ DWC_MODIFY_REG32(&global_regs->gintmsk, intr_mask.d32, intr_mask.d32);
-+
-+ DWC_DEBUGPL(DBG_CIL, "%s() gintmsk=%0x\n", __func__,
-+ DWC_READ_REG32(&global_regs->gintmsk));
-+}
-+
-+/**
-+ * This function initializes the DWC_otg controller registers for
-+ * device mode.
-+ *
-+ * @param core_if Programming view of DWC_otg controller
-+ *
-+ */
-+void dwc_otg_core_dev_init(dwc_otg_core_if_t * core_if)
-+{
-+ int i;
-+ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs;
-+ dwc_otg_dev_if_t *dev_if = core_if->dev_if;
-+ dwc_otg_core_params_t *params = core_if->core_params;
-+ dcfg_data_t dcfg = {.d32 = 0 };
-+ depctl_data_t diepctl = {.d32 = 0 };
-+ grstctl_t resetctl = {.d32 = 0 };
-+ uint32_t rx_fifo_size;
-+ fifosize_data_t nptxfifosize;
-+ fifosize_data_t txfifosize;
-+ dthrctl_data_t dthrctl;
-+ fifosize_data_t ptxfifosize;
-+ uint16_t rxfsiz, nptxfsiz;
-+ gdfifocfg_data_t gdfifocfg = {.d32 = 0 };
-+ hwcfg3_data_t hwcfg3 = {.d32 = 0 };
-+
-+ /* Restart the Phy Clock */
-+ DWC_WRITE_REG32(core_if->pcgcctl, 0);
-+
-+ /* Device configuration register */
-+ init_devspd(core_if);
-+ dcfg.d32 = DWC_READ_REG32(&dev_if->dev_global_regs->dcfg);
-+ dcfg.b.descdma = (core_if->dma_desc_enable) ? 1 : 0;
-+ dcfg.b.perfrint = DWC_DCFG_FRAME_INTERVAL_80;
-+ /* Enable Device OUT NAK in case of DDMA mode*/
-+ if (core_if->core_params->dev_out_nak) {
-+ dcfg.b.endevoutnak = 1;
-+ }
-+
-+ if (core_if->core_params->cont_on_bna) {
-+ dctl_data_t dctl = {.d32 = 0 };
-+ dctl.b.encontonbna = 1;
-+ DWC_MODIFY_REG32(&dev_if->dev_global_regs->dctl, 0, dctl.d32);
-+ }
-+
-+
-+ DWC_WRITE_REG32(&dev_if->dev_global_regs->dcfg, dcfg.d32);
-+
-+ /* Configure data FIFO sizes */
-+ if (core_if->hwcfg2.b.dynamic_fifo && params->enable_dynamic_fifo) {
-+ DWC_DEBUGPL(DBG_CIL, "Total FIFO Size=%d\n",
-+ core_if->total_fifo_size);
-+ DWC_DEBUGPL(DBG_CIL, "Rx FIFO Size=%d\n",
-+ params->dev_rx_fifo_size);
-+ DWC_DEBUGPL(DBG_CIL, "NP Tx FIFO Size=%d\n",
-+ params->dev_nperio_tx_fifo_size);
-+
-+ /* Rx FIFO */
-+ DWC_DEBUGPL(DBG_CIL, "initial grxfsiz=%08x\n",
-+ DWC_READ_REG32(&global_regs->grxfsiz));
-+
-+#ifdef DWC_UTE_CFI
-+ core_if->pwron_rxfsiz = DWC_READ_REG32(&global_regs->grxfsiz);
-+ core_if->init_rxfsiz = params->dev_rx_fifo_size;
-+#endif
-+ rx_fifo_size = params->dev_rx_fifo_size;
-+ DWC_WRITE_REG32(&global_regs->grxfsiz, rx_fifo_size);
-+
-+ DWC_DEBUGPL(DBG_CIL, "new grxfsiz=%08x\n",
-+ DWC_READ_REG32(&global_regs->grxfsiz));
-+
-+ /** Set Periodic Tx FIFO Mask all bits 0 */
-+ core_if->p_tx_msk = 0;
-+
-+ /** Set Tx FIFO Mask all bits 0 */
-+ core_if->tx_msk = 0;
-+
-+ if (core_if->en_multiple_tx_fifo == 0) {
-+ /* Non-periodic Tx FIFO */
-+ DWC_DEBUGPL(DBG_CIL, "initial gnptxfsiz=%08x\n",
-+ DWC_READ_REG32(&global_regs->gnptxfsiz));
-+
-+ nptxfifosize.b.depth = params->dev_nperio_tx_fifo_size;
-+ nptxfifosize.b.startaddr = params->dev_rx_fifo_size;
-+
-+ DWC_WRITE_REG32(&global_regs->gnptxfsiz,
-+ nptxfifosize.d32);
-+
-+ DWC_DEBUGPL(DBG_CIL, "new gnptxfsiz=%08x\n",
-+ DWC_READ_REG32(&global_regs->gnptxfsiz));
-+
-+ /**@todo NGS: Fix Periodic FIFO Sizing! */
-+ /*
-+ * Periodic Tx FIFOs These FIFOs are numbered from 1 to 15.
-+ * Indexes of the FIFO size module parameters in the
-+ * dev_perio_tx_fifo_size array and the FIFO size registers in
-+ * the dptxfsiz array run from 0 to 14.
-+ */
-+ /** @todo Finish debug of this */
-+ ptxfifosize.b.startaddr =
-+ nptxfifosize.b.startaddr + nptxfifosize.b.depth;
-+ for (i = 0; i < core_if->hwcfg4.b.num_dev_perio_in_ep; i++) {
-+ ptxfifosize.b.depth =
-+ params->dev_perio_tx_fifo_size[i];
-+ DWC_DEBUGPL(DBG_CIL,
-+ "initial dtxfsiz[%d]=%08x\n", i,
-+ DWC_READ_REG32(&global_regs->dtxfsiz
-+ [i]));
-+ DWC_WRITE_REG32(&global_regs->dtxfsiz[i],
-+ ptxfifosize.d32);
-+ DWC_DEBUGPL(DBG_CIL, "new dtxfsiz[%d]=%08x\n",
-+ i,
-+ DWC_READ_REG32(&global_regs->dtxfsiz
-+ [i]));
-+ ptxfifosize.b.startaddr += ptxfifosize.b.depth;
-+ }
-+ } else {
-+ /*
-+ * Tx FIFOs These FIFOs are numbered from 1 to 15.
-+ * Indexes of the FIFO size module parameters in the
-+ * dev_tx_fifo_size array and the FIFO size registers in
-+ * the dtxfsiz array run from 0 to 14.
-+ */
-+
-+ /* Non-periodic Tx FIFO */
-+ DWC_DEBUGPL(DBG_CIL, "initial gnptxfsiz=%08x\n",
-+ DWC_READ_REG32(&global_regs->gnptxfsiz));
-+
-+#ifdef DWC_UTE_CFI
-+ core_if->pwron_gnptxfsiz =
-+ (DWC_READ_REG32(&global_regs->gnptxfsiz) >> 16);
-+ core_if->init_gnptxfsiz =
-+ params->dev_nperio_tx_fifo_size;
-+#endif
-+ nptxfifosize.b.depth = params->dev_nperio_tx_fifo_size;
-+ nptxfifosize.b.startaddr = params->dev_rx_fifo_size;
-+
-+ DWC_WRITE_REG32(&global_regs->gnptxfsiz,
-+ nptxfifosize.d32);
-+
-+ DWC_DEBUGPL(DBG_CIL, "new gnptxfsiz=%08x\n",
-+ DWC_READ_REG32(&global_regs->gnptxfsiz));
-+
-+ txfifosize.b.startaddr =
-+ nptxfifosize.b.startaddr + nptxfifosize.b.depth;
-+
-+ for (i = 0; i < core_if->hwcfg4.b.num_in_eps; i++) {
-+
-+ txfifosize.b.depth =
-+ params->dev_tx_fifo_size[i];
-+
-+ DWC_DEBUGPL(DBG_CIL,
-+ "initial dtxfsiz[%d]=%08x\n",
-+ i,
-+ DWC_READ_REG32(&global_regs->dtxfsiz
-+ [i]));
-+
-+#ifdef DWC_UTE_CFI
-+ core_if->pwron_txfsiz[i] =
-+ (DWC_READ_REG32
-+ (&global_regs->dtxfsiz[i]) >> 16);
-+ core_if->init_txfsiz[i] =
-+ params->dev_tx_fifo_size[i];
-+#endif
-+ DWC_WRITE_REG32(&global_regs->dtxfsiz[i],
-+ txfifosize.d32);
-+
-+ DWC_DEBUGPL(DBG_CIL,
-+ "new dtxfsiz[%d]=%08x\n",
-+ i,
-+ DWC_READ_REG32(&global_regs->dtxfsiz
-+ [i]));
-+
-+ txfifosize.b.startaddr += txfifosize.b.depth;
-+ }
-+ if (core_if->snpsid <= OTG_CORE_REV_2_94a) {
-+ /* Calculating DFIFOCFG for Device mode to include RxFIFO and NPTXFIFO */
-+ gdfifocfg.d32 = DWC_READ_REG32(&global_regs->gdfifocfg);
-+ hwcfg3.d32 = DWC_READ_REG32(&global_regs->ghwcfg3);
-+ gdfifocfg.b.gdfifocfg = (DWC_READ_REG32(&global_regs->ghwcfg3) >> 16);
-+ DWC_WRITE_REG32(&global_regs->gdfifocfg, gdfifocfg.d32);
-+ rxfsiz = (DWC_READ_REG32(&global_regs->grxfsiz) & 0x0000ffff);
-+ nptxfsiz = (DWC_READ_REG32(&global_regs->gnptxfsiz) >> 16);
-+ gdfifocfg.b.epinfobase = rxfsiz + nptxfsiz;
-+ DWC_WRITE_REG32(&global_regs->gdfifocfg, gdfifocfg.d32);
-+ }
-+ }
-+
-+ /* Flush the FIFOs */
-+ dwc_otg_flush_tx_fifo(core_if, 0x10); /* all Tx FIFOs */
-+ dwc_otg_flush_rx_fifo(core_if);
-+
-+ /* Flush the Learning Queue. */
-+ resetctl.b.intknqflsh = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->grstctl, resetctl.d32);
-+
-+ if (!core_if->core_params->en_multiple_tx_fifo && core_if->dma_enable) {
-+ core_if->start_predict = 0;
-+ for (i = 0; i<= core_if->dev_if->num_in_eps; ++i) {
-+ core_if->nextep_seq[i] = 0xff; // 0xff - EP not active
-+ }
-+ core_if->nextep_seq[0] = 0;
-+ core_if->first_in_nextep_seq = 0;
-+ diepctl.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[0]->diepctl);
-+ diepctl.b.nextep = 0;
-+ DWC_WRITE_REG32(&dev_if->in_ep_regs[0]->diepctl, diepctl.d32);
-+
-+ /* Update IN Endpoint Mismatch Count by active IN NP EP count + 1 */
-+ dcfg.d32 = DWC_READ_REG32(&dev_if->dev_global_regs->dcfg);
-+ dcfg.b.epmscnt = 2;
-+ DWC_WRITE_REG32(&dev_if->dev_global_regs->dcfg, dcfg.d32);
-+
-+ DWC_DEBUGPL(DBG_CILV,"%s first_in_nextep_seq= %2d; nextep_seq[]:\n",
-+ __func__, core_if->first_in_nextep_seq);
-+ for (i=0; i <= core_if->dev_if->num_in_eps; i++) {
-+ DWC_DEBUGPL(DBG_CILV, "%2d ", core_if->nextep_seq[i]);
-+ }
-+ DWC_DEBUGPL(DBG_CILV,"\n");
-+ }
-+
-+ /* Clear all pending Device Interrupts */
-+ /** @todo - if the condition needed to be checked
-+ * or in any case all pending interrutps should be cleared?
-+ */
-+ if (core_if->multiproc_int_enable) {
-+ for (i = 0; i < core_if->dev_if->num_in_eps; ++i) {
-+ DWC_WRITE_REG32(&dev_if->
-+ dev_global_regs->diepeachintmsk[i], 0);
-+ }
-+ }
-+
-+ for (i = 0; i < core_if->dev_if->num_out_eps; ++i) {
-+ DWC_WRITE_REG32(&dev_if->
-+ dev_global_regs->doepeachintmsk[i], 0);
-+ }
-+
-+ DWC_WRITE_REG32(&dev_if->dev_global_regs->deachint, 0xFFFFFFFF);
-+ DWC_WRITE_REG32(&dev_if->dev_global_regs->deachintmsk, 0);
-+ } else {
-+ DWC_WRITE_REG32(&dev_if->dev_global_regs->diepmsk, 0);
-+ DWC_WRITE_REG32(&dev_if->dev_global_regs->doepmsk, 0);
-+ DWC_WRITE_REG32(&dev_if->dev_global_regs->daint, 0xFFFFFFFF);
-+ DWC_WRITE_REG32(&dev_if->dev_global_regs->daintmsk, 0);
-+ }
-+
-+ for (i = 0; i <= dev_if->num_in_eps; i++) {
-+ depctl_data_t depctl;
-+ depctl.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[i]->diepctl);
-+ if (depctl.b.epena) {
-+ depctl.d32 = 0;
-+ depctl.b.epdis = 1;
-+ depctl.b.snak = 1;
-+ } else {
-+ depctl.d32 = 0;
-+ }
-+
-+ DWC_WRITE_REG32(&dev_if->in_ep_regs[i]->diepctl, depctl.d32);
-+
-+ DWC_WRITE_REG32(&dev_if->in_ep_regs[i]->dieptsiz, 0);
-+ DWC_WRITE_REG32(&dev_if->in_ep_regs[i]->diepdma, 0);
-+ DWC_WRITE_REG32(&dev_if->in_ep_regs[i]->diepint, 0xFF);
-+ }
-+
-+ for (i = 0; i <= dev_if->num_out_eps; i++) {
-+ depctl_data_t depctl;
-+ depctl.d32 = DWC_READ_REG32(&dev_if->out_ep_regs[i]->doepctl);
-+ if (depctl.b.epena) {
-+ dctl_data_t dctl = {.d32 = 0 };
-+ gintmsk_data_t gintsts = {.d32 = 0 };
-+ doepint_data_t doepint = {.d32 = 0 };
-+ dctl.b.sgoutnak = 1;
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl, 0, dctl.d32);
-+ do {
-+ dwc_udelay(10);
-+ gintsts.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintsts);
-+ } while (!gintsts.b.goutnakeff);
-+ gintsts.d32 = 0;
-+ gintsts.b.goutnakeff = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32);
-+
-+ depctl.d32 = 0;
-+ depctl.b.epdis = 1;
-+ depctl.b.snak = 1;
-+ DWC_WRITE_REG32(&core_if->dev_if->out_ep_regs[i]->doepctl, depctl.d32);
-+ do {
-+ dwc_udelay(10);
-+ doepint.d32 = DWC_READ_REG32(&core_if->dev_if->
-+ out_ep_regs[i]->doepint);
-+ } while (!doepint.b.epdisabled);
-+
-+ doepint.b.epdisabled = 1;
-+ DWC_WRITE_REG32(&core_if->dev_if->out_ep_regs[i]->doepint, doepint.d32);
-+
-+ dctl.d32 = 0;
-+ dctl.b.cgoutnak = 1;
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl, 0, dctl.d32);
-+ } else {
-+ depctl.d32 = 0;
-+ }
-+
-+ DWC_WRITE_REG32(&dev_if->out_ep_regs[i]->doepctl, depctl.d32);
-+
-+ DWC_WRITE_REG32(&dev_if->out_ep_regs[i]->doeptsiz, 0);
-+ DWC_WRITE_REG32(&dev_if->out_ep_regs[i]->doepdma, 0);
-+ DWC_WRITE_REG32(&dev_if->out_ep_regs[i]->doepint, 0xFF);
-+ }
-+
-+ if (core_if->en_multiple_tx_fifo && core_if->dma_enable) {
-+ dev_if->non_iso_tx_thr_en = params->thr_ctl & 0x1;
-+ dev_if->iso_tx_thr_en = (params->thr_ctl >> 1) & 0x1;
-+ dev_if->rx_thr_en = (params->thr_ctl >> 2) & 0x1;
-+
-+ dev_if->rx_thr_length = params->rx_thr_length;
-+ dev_if->tx_thr_length = params->tx_thr_length;
-+
-+ dev_if->setup_desc_index = 0;
-+
-+ dthrctl.d32 = 0;
-+ dthrctl.b.non_iso_thr_en = dev_if->non_iso_tx_thr_en;
-+ dthrctl.b.iso_thr_en = dev_if->iso_tx_thr_en;
-+ dthrctl.b.tx_thr_len = dev_if->tx_thr_length;
-+ dthrctl.b.rx_thr_en = dev_if->rx_thr_en;
-+ dthrctl.b.rx_thr_len = dev_if->rx_thr_length;
-+ dthrctl.b.ahb_thr_ratio = params->ahb_thr_ratio;
-+
-+ DWC_WRITE_REG32(&dev_if->dev_global_regs->dtknqr3_dthrctl,
-+ dthrctl.d32);
-+
-+ DWC_DEBUGPL(DBG_CIL,
-+ "Non ISO Tx Thr - %d\nISO Tx Thr - %d\nRx Thr - %d\nTx Thr Len - %d\nRx Thr Len - %d\n",
-+ dthrctl.b.non_iso_thr_en, dthrctl.b.iso_thr_en,
-+ dthrctl.b.rx_thr_en, dthrctl.b.tx_thr_len,
-+ dthrctl.b.rx_thr_len);
-+
-+ }
-+
-+ dwc_otg_enable_device_interrupts(core_if);
-+
-+ {
-+ diepmsk_data_t msk = {.d32 = 0 };
-+ msk.b.txfifoundrn = 1;
-+ if (core_if->multiproc_int_enable) {
-+ DWC_MODIFY_REG32(&dev_if->dev_global_regs->
-+ diepeachintmsk[0], msk.d32, msk.d32);
-+ } else {
-+ DWC_MODIFY_REG32(&dev_if->dev_global_regs->diepmsk,
-+ msk.d32, msk.d32);
-+ }
-+ }
-+
-+ if (core_if->multiproc_int_enable) {
-+ /* Set NAK on Babble */
-+ dctl_data_t dctl = {.d32 = 0 };
-+ dctl.b.nakonbble = 1;
-+ DWC_MODIFY_REG32(&dev_if->dev_global_regs->dctl, 0, dctl.d32);
-+ }
-+
-+ if (core_if->snpsid >= OTG_CORE_REV_2_94a) {
-+ dctl_data_t dctl = {.d32 = 0 };
-+ dctl.d32 = DWC_READ_REG32(&dev_if->dev_global_regs->dctl);
-+ dctl.b.sftdiscon = 0;
-+ DWC_WRITE_REG32(&dev_if->dev_global_regs->dctl, dctl.d32);
-+ }
-+}
-+
-+/**
-+ * This function enables the Host mode interrupts.
-+ *
-+ * @param core_if Programming view of DWC_otg controller
-+ */
-+void dwc_otg_enable_host_interrupts(dwc_otg_core_if_t * core_if)
-+{
-+ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs;
-+ gintmsk_data_t intr_mask = {.d32 = 0 };
-+
-+ DWC_DEBUGPL(DBG_CIL, "%s(%p)\n", __func__, core_if);
-+
-+ /* Disable all interrupts. */
-+ DWC_WRITE_REG32(&global_regs->gintmsk, 0);
-+
-+ /* Clear any pending interrupts. */
-+ DWC_WRITE_REG32(&global_regs->gintsts, 0xFFFFFFFF);
-+
-+ /* Enable the common interrupts */
-+ dwc_otg_enable_common_interrupts(core_if);
-+
-+ /*
-+ * Enable host mode interrupts without disturbing common
-+ * interrupts.
-+ */
-+
-+ intr_mask.b.disconnect = 1;
-+ intr_mask.b.portintr = 1;
-+ intr_mask.b.hcintr = 1;
-+
-+ DWC_MODIFY_REG32(&global_regs->gintmsk, intr_mask.d32, intr_mask.d32);
-+}
-+
-+/**
-+ * This function disables the Host Mode interrupts.
-+ *
-+ * @param core_if Programming view of DWC_otg controller
-+ */
-+void dwc_otg_disable_host_interrupts(dwc_otg_core_if_t * core_if)
-+{
-+ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs;
-+ gintmsk_data_t intr_mask = {.d32 = 0 };
-+
-+ DWC_DEBUGPL(DBG_CILV, "%s()\n", __func__);
-+
-+ /*
-+ * Disable host mode interrupts without disturbing common
-+ * interrupts.
-+ */
-+ intr_mask.b.sofintr = 1;
-+ intr_mask.b.portintr = 1;
-+ intr_mask.b.hcintr = 1;
-+ intr_mask.b.ptxfempty = 1;
-+ intr_mask.b.nptxfempty = 1;
-+
-+ DWC_MODIFY_REG32(&global_regs->gintmsk, intr_mask.d32, 0);
-+}
-+
-+/**
-+ * This function initializes the DWC_otg controller registers for
-+ * host mode.
-+ *
-+ * This function flushes the Tx and Rx FIFOs and it flushes any entries in the
-+ * request queues. Host channels are reset to ensure that they are ready for
-+ * performing transfers.
-+ *
-+ * @param core_if Programming view of DWC_otg controller
-+ *
-+ */
-+void dwc_otg_core_host_init(dwc_otg_core_if_t * core_if)
-+{
-+ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs;
-+ dwc_otg_host_if_t *host_if = core_if->host_if;
-+ dwc_otg_core_params_t *params = core_if->core_params;
-+ hprt0_data_t hprt0 = {.d32 = 0 };
-+ fifosize_data_t nptxfifosize;
-+ fifosize_data_t ptxfifosize;
-+ uint16_t rxfsiz, nptxfsiz, hptxfsiz;
-+ gdfifocfg_data_t gdfifocfg = {.d32 = 0 };
-+ int i;
-+ hcchar_data_t hcchar;
-+ hcfg_data_t hcfg;
-+ hfir_data_t hfir;
-+ dwc_otg_hc_regs_t *hc_regs;
-+ int num_channels;
-+ gotgctl_data_t gotgctl = {.d32 = 0 };
-+
-+ DWC_DEBUGPL(DBG_CILV, "%s(%p)\n", __func__, core_if);
-+
-+ /* Restart the Phy Clock */
-+ DWC_WRITE_REG32(core_if->pcgcctl, 0);
-+
-+ /* Initialize Host Configuration Register */
-+ init_fslspclksel(core_if);
-+ if (core_if->core_params->speed == DWC_SPEED_PARAM_FULL) {
-+ hcfg.d32 = DWC_READ_REG32(&host_if->host_global_regs->hcfg);
-+ hcfg.b.fslssupp = 1;
-+ DWC_WRITE_REG32(&host_if->host_global_regs->hcfg, hcfg.d32);
-+
-+ }
-+
-+ /* This bit allows dynamic reloading of the HFIR register
-+ * during runtime. This bit needs to be programmed during
-+ * initial configuration and its value must not be changed
-+ * during runtime.*/
-+ if (core_if->core_params->reload_ctl == 1) {
-+ hfir.d32 = DWC_READ_REG32(&host_if->host_global_regs->hfir);
-+ hfir.b.hfirrldctrl = 1;
-+ DWC_WRITE_REG32(&host_if->host_global_regs->hfir, hfir.d32);
-+ }
-+
-+ if (core_if->core_params->dma_desc_enable) {
-+ uint8_t op_mode = core_if->hwcfg2.b.op_mode;
-+ if (!
-+ (core_if->hwcfg4.b.desc_dma
-+ && (core_if->snpsid >= OTG_CORE_REV_2_90a)
-+ && ((op_mode == DWC_HWCFG2_OP_MODE_HNP_SRP_CAPABLE_OTG)
-+ || (op_mode == DWC_HWCFG2_OP_MODE_SRP_ONLY_CAPABLE_OTG)
-+ || (op_mode ==
-+ DWC_HWCFG2_OP_MODE_NO_HNP_SRP_CAPABLE_OTG)
-+ || (op_mode == DWC_HWCFG2_OP_MODE_SRP_CAPABLE_HOST)
-+ || (op_mode ==
-+ DWC_HWCFG2_OP_MODE_NO_SRP_CAPABLE_HOST)))) {
-+
-+ DWC_ERROR("Host can't operate in Descriptor DMA mode.\n"
-+ "Either core version is below 2.90a or "
-+ "GHWCFG2, GHWCFG4 registers' values do not allow Descriptor DMA in host mode.\n"
-+ "To run the driver in Buffer DMA host mode set dma_desc_enable "
-+ "module parameter to 0.\n");
-+ return;
-+ }
-+ hcfg.d32 = DWC_READ_REG32(&host_if->host_global_regs->hcfg);
-+ hcfg.b.descdma = 1;
-+ DWC_WRITE_REG32(&host_if->host_global_regs->hcfg, hcfg.d32);
-+ }
-+
-+ /* Configure data FIFO sizes */
-+ if (core_if->hwcfg2.b.dynamic_fifo && params->enable_dynamic_fifo) {
-+ DWC_DEBUGPL(DBG_CIL, "Total FIFO Size=%d\n",
-+ core_if->total_fifo_size);
-+ DWC_DEBUGPL(DBG_CIL, "Rx FIFO Size=%d\n",
-+ params->host_rx_fifo_size);
-+ DWC_DEBUGPL(DBG_CIL, "NP Tx FIFO Size=%d\n",
-+ params->host_nperio_tx_fifo_size);
-+ DWC_DEBUGPL(DBG_CIL, "P Tx FIFO Size=%d\n",
-+ params->host_perio_tx_fifo_size);
-+
-+ /* Rx FIFO */
-+ DWC_DEBUGPL(DBG_CIL, "initial grxfsiz=%08x\n",
-+ DWC_READ_REG32(&global_regs->grxfsiz));
-+ DWC_WRITE_REG32(&global_regs->grxfsiz,
-+ params->host_rx_fifo_size);
-+ DWC_DEBUGPL(DBG_CIL, "new grxfsiz=%08x\n",
-+ DWC_READ_REG32(&global_regs->grxfsiz));
-+
-+ /* Non-periodic Tx FIFO */
-+ DWC_DEBUGPL(DBG_CIL, "initial gnptxfsiz=%08x\n",
-+ DWC_READ_REG32(&global_regs->gnptxfsiz));
-+ nptxfifosize.b.depth = params->host_nperio_tx_fifo_size;
-+ nptxfifosize.b.startaddr = params->host_rx_fifo_size;
-+ DWC_WRITE_REG32(&global_regs->gnptxfsiz, nptxfifosize.d32);
-+ DWC_DEBUGPL(DBG_CIL, "new gnptxfsiz=%08x\n",
-+ DWC_READ_REG32(&global_regs->gnptxfsiz));
-+
-+ /* Periodic Tx FIFO */
-+ DWC_DEBUGPL(DBG_CIL, "initial hptxfsiz=%08x\n",
-+ DWC_READ_REG32(&global_regs->hptxfsiz));
-+ ptxfifosize.b.depth = params->host_perio_tx_fifo_size;
-+ ptxfifosize.b.startaddr =
-+ nptxfifosize.b.startaddr + nptxfifosize.b.depth;
-+ DWC_WRITE_REG32(&global_regs->hptxfsiz, ptxfifosize.d32);
-+ DWC_DEBUGPL(DBG_CIL, "new hptxfsiz=%08x\n",
-+ DWC_READ_REG32(&global_regs->hptxfsiz));
-+
-+ if (core_if->en_multiple_tx_fifo
-+ && core_if->snpsid <= OTG_CORE_REV_2_94a) {
-+ /* Global DFIFOCFG calculation for Host mode - include RxFIFO, NPTXFIFO and HPTXFIFO */
-+ gdfifocfg.d32 = DWC_READ_REG32(&global_regs->gdfifocfg);
-+ rxfsiz = (DWC_READ_REG32(&global_regs->grxfsiz) & 0x0000ffff);
-+ nptxfsiz = (DWC_READ_REG32(&global_regs->gnptxfsiz) >> 16);
-+ hptxfsiz = (DWC_READ_REG32(&global_regs->hptxfsiz) >> 16);
-+ gdfifocfg.b.epinfobase = rxfsiz + nptxfsiz + hptxfsiz;
-+ DWC_WRITE_REG32(&global_regs->gdfifocfg, gdfifocfg.d32);
-+ }
-+ }
-+
-+ /* TODO - check this */
-+ /* Clear Host Set HNP Enable in the OTG Control Register */
-+ gotgctl.b.hstsethnpen = 1;
-+ DWC_MODIFY_REG32(&global_regs->gotgctl, gotgctl.d32, 0);
-+ /* Make sure the FIFOs are flushed. */
-+ dwc_otg_flush_tx_fifo(core_if, 0x10 /* all TX FIFOs */ );
-+ dwc_otg_flush_rx_fifo(core_if);
-+
-+ /* Clear Host Set HNP Enable in the OTG Control Register */
-+ gotgctl.b.hstsethnpen = 1;
-+ DWC_MODIFY_REG32(&global_regs->gotgctl, gotgctl.d32, 0);
-+
-+ if (!core_if->core_params->dma_desc_enable) {
-+ /* Flush out any leftover queued requests. */
-+ num_channels = core_if->core_params->host_channels;
-+
-+ for (i = 0; i < num_channels; i++) {
-+ hc_regs = core_if->host_if->hc_regs[i];
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+ hcchar.b.chen = 0;
-+ hcchar.b.chdis = 1;
-+ hcchar.b.epdir = 0;
-+ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32);
-+ }
-+
-+ /* Halt all channels to put them into a known state. */
-+ for (i = 0; i < num_channels; i++) {
-+ int count = 0;
-+ hc_regs = core_if->host_if->hc_regs[i];
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+ hcchar.b.chen = 1;
-+ hcchar.b.chdis = 1;
-+ hcchar.b.epdir = 0;
-+ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32);
-+ DWC_DEBUGPL(DBG_HCDV, "%s: Halt channel %d regs %p\n", __func__, i, hc_regs);
-+ do {
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+ if (++count > 1000) {
-+ DWC_ERROR
-+ ("%s: Unable to clear halt on channel %d (timeout HCCHAR 0x%X @%p)\n",
-+ __func__, i, hcchar.d32, &hc_regs->hcchar);
-+ break;
-+ }
-+ dwc_udelay(1);
-+ } while (hcchar.b.chen);
-+ }
-+ }
-+
-+ /* Turn on the vbus power. */
-+ DWC_PRINTF("Init: Port Power? op_state=%d\n", core_if->op_state);
-+ if (core_if->op_state == A_HOST) {
-+ hprt0.d32 = dwc_otg_read_hprt0(core_if);
-+ DWC_PRINTF("Init: Power Port (%d)\n", hprt0.b.prtpwr);
-+ if (hprt0.b.prtpwr == 0) {
-+ hprt0.b.prtpwr = 1;
-+ DWC_WRITE_REG32(host_if->hprt0, hprt0.d32);
-+ }
-+ }
-+
-+ dwc_otg_enable_host_interrupts(core_if);
-+}
-+
-+/**
-+ * Prepares a host channel for transferring packets to/from a specific
-+ * endpoint. The HCCHARn register is set up with the characteristics specified
-+ * in _hc. Host channel interrupts that may need to be serviced while this
-+ * transfer is in progress are enabled.
-+ *
-+ * @param core_if Programming view of DWC_otg controller
-+ * @param hc Information needed to initialize the host channel
-+ */
-+void dwc_otg_hc_init(dwc_otg_core_if_t * core_if, dwc_hc_t * hc)
-+{
-+ hcintmsk_data_t hc_intr_mask;
-+ hcchar_data_t hcchar;
-+ hcsplt_data_t hcsplt;
-+
-+ uint8_t hc_num = hc->hc_num;
-+ dwc_otg_host_if_t *host_if = core_if->host_if;
-+ dwc_otg_hc_regs_t *hc_regs = host_if->hc_regs[hc_num];
-+
-+ /* Clear old interrupt conditions for this host channel. */
-+ hc_intr_mask.d32 = 0xFFFFFFFF;
-+ hc_intr_mask.b.reserved14_31 = 0;
-+ DWC_WRITE_REG32(&hc_regs->hcint, hc_intr_mask.d32);
-+
-+ /* Enable channel interrupts required for this transfer. */
-+ hc_intr_mask.d32 = 0;
-+ hc_intr_mask.b.chhltd = 1;
-+ if (core_if->dma_enable) {
-+ /* For Descriptor DMA mode core halts the channel on AHB error. Interrupt is not required */
-+ if (!core_if->dma_desc_enable)
-+ hc_intr_mask.b.ahberr = 1;
-+ else {
-+ if (hc->ep_type == DWC_OTG_EP_TYPE_ISOC)
-+ hc_intr_mask.b.xfercompl = 1;
-+ }
-+
-+ if (hc->error_state && !hc->do_split &&
-+ hc->ep_type != DWC_OTG_EP_TYPE_ISOC) {
-+ hc_intr_mask.b.ack = 1;
-+ if (hc->ep_is_in) {
-+ hc_intr_mask.b.datatglerr = 1;
-+ if (hc->ep_type != DWC_OTG_EP_TYPE_INTR) {
-+ hc_intr_mask.b.nak = 1;
-+ }
-+ }
-+ }
-+ } else {
-+ switch (hc->ep_type) {
-+ case DWC_OTG_EP_TYPE_CONTROL:
-+ case DWC_OTG_EP_TYPE_BULK:
-+ hc_intr_mask.b.xfercompl = 1;
-+ hc_intr_mask.b.stall = 1;
-+ hc_intr_mask.b.xacterr = 1;
-+ hc_intr_mask.b.datatglerr = 1;
-+ if (hc->ep_is_in) {
-+ hc_intr_mask.b.bblerr = 1;
-+ } else {
-+ hc_intr_mask.b.nak = 1;
-+ hc_intr_mask.b.nyet = 1;
-+ if (hc->do_ping) {
-+ hc_intr_mask.b.ack = 1;
-+ }
-+ }
-+
-+ if (hc->do_split) {
-+ hc_intr_mask.b.nak = 1;
-+ if (hc->complete_split) {
-+ hc_intr_mask.b.nyet = 1;
-+ } else {
-+ hc_intr_mask.b.ack = 1;
-+ }
-+ }
-+
-+ if (hc->error_state) {
-+ hc_intr_mask.b.ack = 1;
-+ }
-+ break;
-+ case DWC_OTG_EP_TYPE_INTR:
-+ hc_intr_mask.b.xfercompl = 1;
-+ hc_intr_mask.b.nak = 1;
-+ hc_intr_mask.b.stall = 1;
-+ hc_intr_mask.b.xacterr = 1;
-+ hc_intr_mask.b.datatglerr = 1;
-+ hc_intr_mask.b.frmovrun = 1;
-+
-+ if (hc->ep_is_in) {
-+ hc_intr_mask.b.bblerr = 1;
-+ }
-+ if (hc->error_state) {
-+ hc_intr_mask.b.ack = 1;
-+ }
-+ if (hc->do_split) {
-+ if (hc->complete_split) {
-+ hc_intr_mask.b.nyet = 1;
-+ } else {
-+ hc_intr_mask.b.ack = 1;
-+ }
-+ }
-+ break;
-+ case DWC_OTG_EP_TYPE_ISOC:
-+ hc_intr_mask.b.xfercompl = 1;
-+ hc_intr_mask.b.frmovrun = 1;
-+ hc_intr_mask.b.ack = 1;
-+
-+ if (hc->ep_is_in) {
-+ hc_intr_mask.b.xacterr = 1;
-+ hc_intr_mask.b.bblerr = 1;
-+ }
-+ break;
-+ }
-+ }
-+ DWC_WRITE_REG32(&hc_regs->hcintmsk, hc_intr_mask.d32);
-+
-+ /*
-+ * Program the HCCHARn register with the endpoint characteristics for
-+ * the current transfer.
-+ */
-+ hcchar.d32 = 0;
-+ hcchar.b.devaddr = hc->dev_addr;
-+ hcchar.b.epnum = hc->ep_num;
-+ hcchar.b.epdir = hc->ep_is_in;
-+ hcchar.b.lspddev = (hc->speed == DWC_OTG_EP_SPEED_LOW);
-+ hcchar.b.eptype = hc->ep_type;
-+ hcchar.b.mps = hc->max_packet;
-+
-+ DWC_WRITE_REG32(&host_if->hc_regs[hc_num]->hcchar, hcchar.d32);
-+
-+ DWC_DEBUGPL(DBG_HCDV, "%s: Channel %d, Dev Addr %d, EP #%d\n",
-+ __func__, hc->hc_num, hcchar.b.devaddr, hcchar.b.epnum);
-+ DWC_DEBUGPL(DBG_HCDV, " Is In %d, Is Low Speed %d, EP Type %d, "
-+ "Max Pkt %d, Multi Cnt %d\n",
-+ hcchar.b.epdir, hcchar.b.lspddev, hcchar.b.eptype,
-+ hcchar.b.mps, hcchar.b.multicnt);
-+
-+ /*
-+ * Program the HCSPLIT register for SPLITs
-+ */
-+ hcsplt.d32 = 0;
-+ if (hc->do_split) {
-+ DWC_DEBUGPL(DBG_HCDV, "Programming HC %d with split --> %s\n",
-+ hc->hc_num,
-+ hc->complete_split ? "CSPLIT" : "SSPLIT");
-+ hcsplt.b.compsplt = hc->complete_split;
-+ hcsplt.b.xactpos = hc->xact_pos;
-+ hcsplt.b.hubaddr = hc->hub_addr;
-+ hcsplt.b.prtaddr = hc->port_addr;
-+ DWC_DEBUGPL(DBG_HCDV, "\t comp split %d\n", hc->complete_split);
-+ DWC_DEBUGPL(DBG_HCDV, "\t xact pos %d\n", hc->xact_pos);
-+ DWC_DEBUGPL(DBG_HCDV, "\t hub addr %d\n", hc->hub_addr);
-+ DWC_DEBUGPL(DBG_HCDV, "\t port addr %d\n", hc->port_addr);
-+ DWC_DEBUGPL(DBG_HCDV, "\t is_in %d\n", hc->ep_is_in);
-+ DWC_DEBUGPL(DBG_HCDV, "\t Max Pkt: %d\n", hcchar.b.mps);
-+ DWC_DEBUGPL(DBG_HCDV, "\t xferlen: %d\n", hc->xfer_len);
-+ }
-+ DWC_WRITE_REG32(&host_if->hc_regs[hc_num]->hcsplt, hcsplt.d32);
-+
-+}
-+
-+/**
-+ * Attempts to halt a host channel. This function should only be called in
-+ * Slave mode or to abort a transfer in either Slave mode or DMA mode. Under
-+ * normal circumstances in DMA mode, the controller halts the channel when the
-+ * transfer is complete or a condition occurs that requires application
-+ * intervention.
-+ *
-+ * In slave mode, checks for a free request queue entry, then sets the Channel
-+ * Enable and Channel Disable bits of the Host Channel Characteristics
-+ * register of the specified channel to intiate the halt. If there is no free
-+ * request queue entry, sets only the Channel Disable bit of the HCCHARn
-+ * register to flush requests for this channel. In the latter case, sets a
-+ * flag to indicate that the host channel needs to be halted when a request
-+ * queue slot is open.
-+ *
-+ * In DMA mode, always sets the Channel Enable and Channel Disable bits of the
-+ * HCCHARn register. The controller ensures there is space in the request
-+ * queue before submitting the halt request.
-+ *
-+ * Some time may elapse before the core flushes any posted requests for this
-+ * host channel and halts. The Channel Halted interrupt handler completes the
-+ * deactivation of the host channel.
-+ *
-+ * @param core_if Controller register interface.
-+ * @param hc Host channel to halt.
-+ * @param halt_status Reason for halting the channel.
-+ */
-+void dwc_otg_hc_halt(dwc_otg_core_if_t * core_if,
-+ dwc_hc_t * hc, dwc_otg_halt_status_e halt_status)
-+{
-+ gnptxsts_data_t nptxsts;
-+ hptxsts_data_t hptxsts;
-+ hcchar_data_t hcchar;
-+ dwc_otg_hc_regs_t *hc_regs;
-+ dwc_otg_core_global_regs_t *global_regs;
-+ dwc_otg_host_global_regs_t *host_global_regs;
-+
-+ hc_regs = core_if->host_if->hc_regs[hc->hc_num];
-+ global_regs = core_if->core_global_regs;
-+ host_global_regs = core_if->host_if->host_global_regs;
-+
-+ DWC_ASSERT(!(halt_status == DWC_OTG_HC_XFER_NO_HALT_STATUS),
-+ "halt_status = %d\n", halt_status);
-+
-+ if (halt_status == DWC_OTG_HC_XFER_URB_DEQUEUE ||
-+ halt_status == DWC_OTG_HC_XFER_AHB_ERR) {
-+ /*
-+ * Disable all channel interrupts except Ch Halted. The QTD
-+ * and QH state associated with this transfer has been cleared
-+ * (in the case of URB_DEQUEUE), so the channel needs to be
-+ * shut down carefully to prevent crashes.
-+ */
-+ hcintmsk_data_t hcintmsk;
-+ hcintmsk.d32 = 0;
-+ hcintmsk.b.chhltd = 1;
-+ DWC_WRITE_REG32(&hc_regs->hcintmsk, hcintmsk.d32);
-+
-+ /*
-+ * Make sure no other interrupts besides halt are currently
-+ * pending. Handling another interrupt could cause a crash due
-+ * to the QTD and QH state.
-+ */
-+ DWC_WRITE_REG32(&hc_regs->hcint, ~hcintmsk.d32);
-+
-+ /*
-+ * Make sure the halt status is set to URB_DEQUEUE or AHB_ERR
-+ * even if the channel was already halted for some other
-+ * reason.
-+ */
-+ hc->halt_status = halt_status;
-+
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+ if (hcchar.b.chen == 0) {
-+ /*
-+ * The channel is either already halted or it hasn't
-+ * started yet. In DMA mode, the transfer may halt if
-+ * it finishes normally or a condition occurs that
-+ * requires driver intervention. Don't want to halt
-+ * the channel again. In either Slave or DMA mode,
-+ * it's possible that the transfer has been assigned
-+ * to a channel, but not started yet when an URB is
-+ * dequeued. Don't want to halt a channel that hasn't
-+ * started yet.
-+ */
-+ return;
-+ }
-+ }
-+ if (hc->halt_pending) {
-+ /*
-+ * A halt has already been issued for this channel. This might
-+ * happen when a transfer is aborted by a higher level in
-+ * the stack.
-+ */
-+#ifdef DEBUG
-+ DWC_PRINTF
-+ ("*** %s: Channel %d, _hc->halt_pending already set ***\n",
-+ __func__, hc->hc_num);
-+
-+#endif
-+ return;
-+ }
-+
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+
-+ /* No need to set the bit in DDMA for disabling the channel */
-+ //TODO check it everywhere channel is disabled
-+ if (!core_if->core_params->dma_desc_enable)
-+ hcchar.b.chen = 1;
-+ hcchar.b.chdis = 1;
-+
-+ if (!core_if->dma_enable) {
-+ /* Check for space in the request queue to issue the halt. */
-+ if (hc->ep_type == DWC_OTG_EP_TYPE_CONTROL ||
-+ hc->ep_type == DWC_OTG_EP_TYPE_BULK) {
-+ nptxsts.d32 = DWC_READ_REG32(&global_regs->gnptxsts);
-+ if (nptxsts.b.nptxqspcavail == 0) {
-+ hcchar.b.chen = 0;
-+ }
-+ } else {
-+ hptxsts.d32 =
-+ DWC_READ_REG32(&host_global_regs->hptxsts);
-+ if ((hptxsts.b.ptxqspcavail == 0)
-+ || (core_if->queuing_high_bandwidth)) {
-+ hcchar.b.chen = 0;
-+ }
-+ }
-+ }
-+ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32);
-+
-+ hc->halt_status = halt_status;
-+
-+ if (hcchar.b.chen) {
-+ hc->halt_pending = 1;
-+ hc->halt_on_queue = 0;
-+ } else {
-+ hc->halt_on_queue = 1;
-+ }
-+
-+ DWC_DEBUGPL(DBG_HCDV, "%s: Channel %d\n", __func__, hc->hc_num);
-+ DWC_DEBUGPL(DBG_HCDV, " hcchar: 0x%08x\n", hcchar.d32);
-+ DWC_DEBUGPL(DBG_HCDV, " halt_pending: %d\n", hc->halt_pending);
-+ DWC_DEBUGPL(DBG_HCDV, " halt_on_queue: %d\n", hc->halt_on_queue);
-+ DWC_DEBUGPL(DBG_HCDV, " halt_status: %d\n", hc->halt_status);
-+
-+ return;
-+}
-+
-+/**
-+ * Clears the transfer state for a host channel. This function is normally
-+ * called after a transfer is done and the host channel is being released.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param hc Identifies the host channel to clean up.
-+ */
-+void dwc_otg_hc_cleanup(dwc_otg_core_if_t * core_if, dwc_hc_t * hc)
-+{
-+ dwc_otg_hc_regs_t *hc_regs;
-+
-+ hc->xfer_started = 0;
-+
-+ /*
-+ * Clear channel interrupt enables and any unhandled channel interrupt
-+ * conditions.
-+ */
-+ hc_regs = core_if->host_if->hc_regs[hc->hc_num];
-+ DWC_WRITE_REG32(&hc_regs->hcintmsk, 0);
-+ DWC_WRITE_REG32(&hc_regs->hcint, 0xFFFFFFFF);
-+#ifdef DEBUG
-+ DWC_TIMER_CANCEL(core_if->hc_xfer_timer[hc->hc_num]);
-+#endif
-+}
-+
-+/**
-+ * Sets the channel property that indicates in which frame a periodic transfer
-+ * should occur. This is always set to the _next_ frame. This function has no
-+ * effect on non-periodic transfers.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param hc Identifies the host channel to set up and its properties.
-+ * @param hcchar Current value of the HCCHAR register for the specified host
-+ * channel.
-+ */
-+static inline void hc_set_even_odd_frame(dwc_otg_core_if_t * core_if,
-+ dwc_hc_t * hc, hcchar_data_t * hcchar)
-+{
-+ if (hc->ep_type == DWC_OTG_EP_TYPE_INTR ||
-+ hc->ep_type == DWC_OTG_EP_TYPE_ISOC) {
-+ hfnum_data_t hfnum;
-+ hfnum.d32 =
-+ DWC_READ_REG32(&core_if->host_if->host_global_regs->hfnum);
-+
-+ /* 1 if _next_ frame is odd, 0 if it's even */
-+ hcchar->b.oddfrm = (hfnum.b.frnum & 0x1) ? 0 : 1;
-+#ifdef DEBUG
-+ if (hc->ep_type == DWC_OTG_EP_TYPE_INTR && hc->do_split
-+ && !hc->complete_split) {
-+ switch (hfnum.b.frnum & 0x7) {
-+ case 7:
-+ core_if->hfnum_7_samples++;
-+ core_if->hfnum_7_frrem_accum += hfnum.b.frrem;
-+ break;
-+ case 0:
-+ core_if->hfnum_0_samples++;
-+ core_if->hfnum_0_frrem_accum += hfnum.b.frrem;
-+ break;
-+ default:
-+ core_if->hfnum_other_samples++;
-+ core_if->hfnum_other_frrem_accum +=
-+ hfnum.b.frrem;
-+ break;
-+ }
-+ }
-+#endif
-+ }
-+}
-+
-+#ifdef DEBUG
-+void hc_xfer_timeout(void *ptr)
-+{
-+ hc_xfer_info_t *xfer_info = NULL;
-+ int hc_num = 0;
-+
-+ if (ptr)
-+ xfer_info = (hc_xfer_info_t *) ptr;
-+
-+ if (!xfer_info->hc) {
-+ DWC_ERROR("xfer_info->hc = %p\n", xfer_info->hc);
-+ return;
-+ }
-+
-+ hc_num = xfer_info->hc->hc_num;
-+ DWC_WARN("%s: timeout on channel %d\n", __func__, hc_num);
-+ DWC_WARN(" start_hcchar_val 0x%08x\n",
-+ xfer_info->core_if->start_hcchar_val[hc_num]);
-+}
-+#endif
-+
-+void ep_xfer_timeout(void *ptr)
-+{
-+ ep_xfer_info_t *xfer_info = NULL;
-+ int ep_num = 0;
-+ dctl_data_t dctl = {.d32 = 0 };
-+ gintsts_data_t gintsts = {.d32 = 0 };
-+ gintmsk_data_t gintmsk = {.d32 = 0 };
-+
-+ if (ptr)
-+ xfer_info = (ep_xfer_info_t *) ptr;
-+
-+ if (!xfer_info->ep) {
-+ DWC_ERROR("xfer_info->ep = %p\n", xfer_info->ep);
-+ return;
-+ }
-+
-+ ep_num = xfer_info->ep->num;
-+ DWC_WARN("%s: timeout on endpoit %d\n", __func__, ep_num);
-+ /* Put the sate to 2 as it was time outed */
-+ xfer_info->state = 2;
-+
-+ dctl.d32 =
-+ DWC_READ_REG32(&xfer_info->core_if->dev_if->dev_global_regs->dctl);
-+ gintsts.d32 =
-+ DWC_READ_REG32(&xfer_info->core_if->core_global_regs->gintsts);
-+ gintmsk.d32 =
-+ DWC_READ_REG32(&xfer_info->core_if->core_global_regs->gintmsk);
-+
-+ if (!gintmsk.b.goutnakeff) {
-+ /* Unmask it */
-+ gintmsk.b.goutnakeff = 1;
-+ DWC_WRITE_REG32(&xfer_info->core_if->core_global_regs->gintmsk,
-+ gintmsk.d32);
-+
-+ }
-+
-+ if (!gintsts.b.goutnakeff) {
-+ dctl.b.sgoutnak = 1;
-+ }
-+ DWC_WRITE_REG32(&xfer_info->core_if->dev_if->dev_global_regs->dctl,
-+ dctl.d32);
-+
-+}
-+
-+void set_pid_isoc(dwc_hc_t * hc)
-+{
-+ /* Set up the initial PID for the transfer. */
-+ if (hc->speed == DWC_OTG_EP_SPEED_HIGH) {
-+ if (hc->ep_is_in) {
-+ if (hc->multi_count == 1) {
-+ hc->data_pid_start = DWC_OTG_HC_PID_DATA0;
-+ } else if (hc->multi_count == 2) {
-+ hc->data_pid_start = DWC_OTG_HC_PID_DATA1;
-+ } else {
-+ hc->data_pid_start = DWC_OTG_HC_PID_DATA2;
-+ }
-+ } else {
-+ if (hc->multi_count == 1) {
-+ hc->data_pid_start = DWC_OTG_HC_PID_DATA0;
-+ } else {
-+ hc->data_pid_start = DWC_OTG_HC_PID_MDATA;
-+ }
-+ }
-+ } else {
-+ hc->data_pid_start = DWC_OTG_HC_PID_DATA0;
-+ }
-+}
-+
-+/**
-+ * This function does the setup for a data transfer for a host channel and
-+ * starts the transfer. May be called in either Slave mode or DMA mode. In
-+ * Slave mode, the caller must ensure that there is sufficient space in the
-+ * request queue and Tx Data FIFO.
-+ *
-+ * For an OUT transfer in Slave mode, it loads a data packet into the
-+ * appropriate FIFO. If necessary, additional data packets will be loaded in
-+ * the Host ISR.
-+ *
-+ * For an IN transfer in Slave mode, a data packet is requested. The data
-+ * packets are unloaded from the Rx FIFO in the Host ISR. If necessary,
-+ * additional data packets are requested in the Host ISR.
-+ *
-+ * For a PING transfer in Slave mode, the Do Ping bit is set in the HCTSIZ
-+ * register along with a packet count of 1 and the channel is enabled. This
-+ * causes a single PING transaction to occur. Other fields in HCTSIZ are
-+ * simply set to 0 since no data transfer occurs in this case.
-+ *
-+ * For a PING transfer in DMA mode, the HCTSIZ register is initialized with
-+ * all the information required to perform the subsequent data transfer. In
-+ * addition, the Do Ping bit is set in the HCTSIZ register. In this case, the
-+ * controller performs the entire PING protocol, then starts the data
-+ * transfer.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param hc Information needed to initialize the host channel. The xfer_len
-+ * value may be reduced to accommodate the max widths of the XferSize and
-+ * PktCnt fields in the HCTSIZn register. The multi_count value may be changed
-+ * to reflect the final xfer_len value.
-+ */
-+void dwc_otg_hc_start_transfer(dwc_otg_core_if_t * core_if, dwc_hc_t * hc)
-+{
-+ hcchar_data_t hcchar;
-+ hctsiz_data_t hctsiz;
-+ uint16_t num_packets;
-+ uint32_t max_hc_xfer_size = core_if->core_params->max_transfer_size;
-+ uint16_t max_hc_pkt_count = core_if->core_params->max_packet_count;
-+ dwc_otg_hc_regs_t *hc_regs = core_if->host_if->hc_regs[hc->hc_num];
-+
-+ hctsiz.d32 = 0;
-+
-+ if (hc->do_ping) {
-+ if (!core_if->dma_enable) {
-+ dwc_otg_hc_do_ping(core_if, hc);
-+ hc->xfer_started = 1;
-+ return;
-+ } else {
-+ hctsiz.b.dopng = 1;
-+ }
-+ }
-+
-+ if (hc->do_split) {
-+ num_packets = 1;
-+
-+ if (hc->complete_split && !hc->ep_is_in) {
-+ /* For CSPLIT OUT Transfer, set the size to 0 so the
-+ * core doesn't expect any data written to the FIFO */
-+ hc->xfer_len = 0;
-+ } else if (hc->ep_is_in || (hc->xfer_len > hc->max_packet)) {
-+ hc->xfer_len = hc->max_packet;
-+ } else if (!hc->ep_is_in && (hc->xfer_len > 188)) {
-+ hc->xfer_len = 188;
-+ }
-+
-+ hctsiz.b.xfersize = hc->xfer_len;
-+ } else {
-+ /*
-+ * Ensure that the transfer length and packet count will fit
-+ * in the widths allocated for them in the HCTSIZn register.
-+ */
-+ if (hc->ep_type == DWC_OTG_EP_TYPE_INTR ||
-+ hc->ep_type == DWC_OTG_EP_TYPE_ISOC) {
-+ /*
-+ * Make sure the transfer size is no larger than one
-+ * (micro)frame's worth of data. (A check was done
-+ * when the periodic transfer was accepted to ensure
-+ * that a (micro)frame's worth of data can be
-+ * programmed into a channel.)
-+ */
-+ uint32_t max_periodic_len =
-+ hc->multi_count * hc->max_packet;
-+ if (hc->xfer_len > max_periodic_len) {
-+ hc->xfer_len = max_periodic_len;
-+ } else {
-+ }
-+ } else if (hc->xfer_len > max_hc_xfer_size) {
-+ /* Make sure that xfer_len is a multiple of max packet size. */
-+ hc->xfer_len = max_hc_xfer_size - hc->max_packet + 1;
-+ }
-+
-+ if (hc->xfer_len > 0) {
-+ num_packets =
-+ (hc->xfer_len + hc->max_packet -
-+ 1) / hc->max_packet;
-+ if (num_packets > max_hc_pkt_count) {
-+ num_packets = max_hc_pkt_count;
-+ hc->xfer_len = num_packets * hc->max_packet;
-+ }
-+ } else {
-+ /* Need 1 packet for transfer length of 0. */
-+ num_packets = 1;
-+ }
-+
-+ if (hc->ep_is_in) {
-+ /* Always program an integral # of max packets for IN transfers. */
-+ hc->xfer_len = num_packets * hc->max_packet;
-+ }
-+
-+ if (hc->ep_type == DWC_OTG_EP_TYPE_INTR ||
-+ hc->ep_type == DWC_OTG_EP_TYPE_ISOC) {
-+ /*
-+ * Make sure that the multi_count field matches the
-+ * actual transfer length.
-+ */
-+ hc->multi_count = num_packets;
-+ }
-+
-+ if (hc->ep_type == DWC_OTG_EP_TYPE_ISOC)
-+ set_pid_isoc(hc);
-+
-+ hctsiz.b.xfersize = hc->xfer_len;
-+ }
-+
-+ hc->start_pkt_count = num_packets;
-+ hctsiz.b.pktcnt = num_packets;
-+ hctsiz.b.pid = hc->data_pid_start;
-+ DWC_WRITE_REG32(&hc_regs->hctsiz, hctsiz.d32);
-+
-+ DWC_DEBUGPL(DBG_HCDV, "%s: Channel %d\n", __func__, hc->hc_num);
-+ DWC_DEBUGPL(DBG_HCDV, " Xfer Size: %d\n", hctsiz.b.xfersize);
-+ DWC_DEBUGPL(DBG_HCDV, " Num Pkts: %d\n", hctsiz.b.pktcnt);
-+ DWC_DEBUGPL(DBG_HCDV, " Start PID: %d\n", hctsiz.b.pid);
-+
-+ if (core_if->dma_enable) {
-+ dwc_dma_t dma_addr;
-+ if (hc->align_buff) {
-+ dma_addr = hc->align_buff;
-+ } else {
-+ dma_addr = ((unsigned long)hc->xfer_buff & 0xffffffff);
-+ }
-+ DWC_WRITE_REG32(&hc_regs->hcdma, dma_addr);
-+ }
-+
-+ /* Start the split */
-+ if (hc->do_split) {
-+ hcsplt_data_t hcsplt;
-+ hcsplt.d32 = DWC_READ_REG32(&hc_regs->hcsplt);
-+ hcsplt.b.spltena = 1;
-+ DWC_WRITE_REG32(&hc_regs->hcsplt, hcsplt.d32);
-+ }
-+
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+ hcchar.b.multicnt = hc->multi_count;
-+ hc_set_even_odd_frame(core_if, hc, &hcchar);
-+#ifdef DEBUG
-+ core_if->start_hcchar_val[hc->hc_num] = hcchar.d32;
-+ if (hcchar.b.chdis) {
-+ DWC_WARN("%s: chdis set, channel %d, hcchar 0x%08x\n",
-+ __func__, hc->hc_num, hcchar.d32);
-+ }
-+#endif
-+
-+ /* Set host channel enable after all other setup is complete. */
-+ hcchar.b.chen = 1;
-+ hcchar.b.chdis = 0;
-+ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32);
-+
-+ hc->xfer_started = 1;
-+ hc->requests++;
-+
-+ if (!core_if->dma_enable && !hc->ep_is_in && hc->xfer_len > 0) {
-+ /* Load OUT packet into the appropriate Tx FIFO. */
-+ dwc_otg_hc_write_packet(core_if, hc);
-+ }
-+#ifdef DEBUG
-+ if (hc->ep_type != DWC_OTG_EP_TYPE_INTR) {
-+ DWC_DEBUGPL(DBG_HCDV, "transfer %d from core_if %p\n",
-+ hc->hc_num, core_if);//GRAYG
-+ core_if->hc_xfer_info[hc->hc_num].core_if = core_if;
-+ core_if->hc_xfer_info[hc->hc_num].hc = hc;
-+
-+ /* Start a timer for this transfer. */
-+ DWC_TIMER_SCHEDULE(core_if->hc_xfer_timer[hc->hc_num], 10000);
-+ }
-+#endif
-+}
-+
-+/**
-+ * This function does the setup for a data transfer for a host channel
-+ * and starts the transfer in Descriptor DMA mode.
-+ *
-+ * Initializes HCTSIZ register. For a PING transfer the Do Ping bit is set.
-+ * Sets PID and NTD values. For periodic transfers
-+ * initializes SCHED_INFO field with micro-frame bitmap.
-+ *
-+ * Initializes HCDMA register with descriptor list address and CTD value
-+ * then starts the transfer via enabling the channel.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param hc Information needed to initialize the host channel.
-+ */
-+void dwc_otg_hc_start_transfer_ddma(dwc_otg_core_if_t * core_if, dwc_hc_t * hc)
-+{
-+ dwc_otg_hc_regs_t *hc_regs = core_if->host_if->hc_regs[hc->hc_num];
-+ hcchar_data_t hcchar;
-+ hctsiz_data_t hctsiz;
-+ hcdma_data_t hcdma;
-+
-+ hctsiz.d32 = 0;
-+
-+ if (hc->do_ping)
-+ hctsiz.b_ddma.dopng = 1;
-+
-+ if (hc->ep_type == DWC_OTG_EP_TYPE_ISOC)
-+ set_pid_isoc(hc);
-+
-+ /* Packet Count and Xfer Size are not used in Descriptor DMA mode */
-+ hctsiz.b_ddma.pid = hc->data_pid_start;
-+ hctsiz.b_ddma.ntd = hc->ntd - 1; /* 0 - 1 descriptor, 1 - 2 descriptors, etc. */
-+ hctsiz.b_ddma.schinfo = hc->schinfo; /* Non-zero only for high-speed interrupt endpoints */
-+
-+ DWC_DEBUGPL(DBG_HCDV, "%s: Channel %d\n", __func__, hc->hc_num);
-+ DWC_DEBUGPL(DBG_HCDV, " Start PID: %d\n", hctsiz.b.pid);
-+ DWC_DEBUGPL(DBG_HCDV, " NTD: %d\n", hctsiz.b_ddma.ntd);
-+
-+ DWC_WRITE_REG32(&hc_regs->hctsiz, hctsiz.d32);
-+
-+ hcdma.d32 = 0;
-+ hcdma.b.dma_addr = ((uint32_t) hc->desc_list_addr) >> 11;
-+
-+ /* Always start from first descriptor. */
-+ hcdma.b.ctd = 0;
-+ DWC_WRITE_REG32(&hc_regs->hcdma, hcdma.d32);
-+
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+ hcchar.b.multicnt = hc->multi_count;
-+
-+#ifdef DEBUG
-+ core_if->start_hcchar_val[hc->hc_num] = hcchar.d32;
-+ if (hcchar.b.chdis) {
-+ DWC_WARN("%s: chdis set, channel %d, hcchar 0x%08x\n",
-+ __func__, hc->hc_num, hcchar.d32);
-+ }
-+#endif
-+
-+ /* Set host channel enable after all other setup is complete. */
-+ hcchar.b.chen = 1;
-+ hcchar.b.chdis = 0;
-+
-+ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32);
-+
-+ hc->xfer_started = 1;
-+ hc->requests++;
-+
-+#ifdef DEBUG
-+ if ((hc->ep_type != DWC_OTG_EP_TYPE_INTR)
-+ && (hc->ep_type != DWC_OTG_EP_TYPE_ISOC)) {
-+ DWC_DEBUGPL(DBG_HCDV, "DMA transfer %d from core_if %p\n",
-+ hc->hc_num, core_if);//GRAYG
-+ core_if->hc_xfer_info[hc->hc_num].core_if = core_if;
-+ core_if->hc_xfer_info[hc->hc_num].hc = hc;
-+ /* Start a timer for this transfer. */
-+ DWC_TIMER_SCHEDULE(core_if->hc_xfer_timer[hc->hc_num], 10000);
-+ }
-+#endif
-+
-+}
-+
-+/**
-+ * This function continues a data transfer that was started by previous call
-+ * to <code>dwc_otg_hc_start_transfer</code>. The caller must ensure there is
-+ * sufficient space in the request queue and Tx Data FIFO. This function
-+ * should only be called in Slave mode. In DMA mode, the controller acts
-+ * autonomously to complete transfers programmed to a host channel.
-+ *
-+ * For an OUT transfer, a new data packet is loaded into the appropriate FIFO
-+ * if there is any data remaining to be queued. For an IN transfer, another
-+ * data packet is always requested. For the SETUP phase of a control transfer,
-+ * this function does nothing.
-+ *
-+ * @return 1 if a new request is queued, 0 if no more requests are required
-+ * for this transfer.
-+ */
-+int dwc_otg_hc_continue_transfer(dwc_otg_core_if_t * core_if, dwc_hc_t * hc)
-+{
-+ DWC_DEBUGPL(DBG_HCDV, "%s: Channel %d\n", __func__, hc->hc_num);
-+
-+ if (hc->do_split) {
-+ /* SPLITs always queue just once per channel */
-+ return 0;
-+ } else if (hc->data_pid_start == DWC_OTG_HC_PID_SETUP) {
-+ /* SETUPs are queued only once since they can't be NAKed. */
-+ return 0;
-+ } else if (hc->ep_is_in) {
-+ /*
-+ * Always queue another request for other IN transfers. If
-+ * back-to-back INs are issued and NAKs are received for both,
-+ * the driver may still be processing the first NAK when the
-+ * second NAK is received. When the interrupt handler clears
-+ * the NAK interrupt for the first NAK, the second NAK will
-+ * not be seen. So we can't depend on the NAK interrupt
-+ * handler to requeue a NAKed request. Instead, IN requests
-+ * are issued each time this function is called. When the
-+ * transfer completes, the extra requests for the channel will
-+ * be flushed.
-+ */
-+ hcchar_data_t hcchar;
-+ dwc_otg_hc_regs_t *hc_regs =
-+ core_if->host_if->hc_regs[hc->hc_num];
-+
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+ hc_set_even_odd_frame(core_if, hc, &hcchar);
-+ hcchar.b.chen = 1;
-+ hcchar.b.chdis = 0;
-+ DWC_DEBUGPL(DBG_HCDV, " IN xfer: hcchar = 0x%08x\n",
-+ hcchar.d32);
-+ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32);
-+ hc->requests++;
-+ return 1;
-+ } else {
-+ /* OUT transfers. */
-+ if (hc->xfer_count < hc->xfer_len) {
-+ if (hc->ep_type == DWC_OTG_EP_TYPE_INTR ||
-+ hc->ep_type == DWC_OTG_EP_TYPE_ISOC) {
-+ hcchar_data_t hcchar;
-+ dwc_otg_hc_regs_t *hc_regs;
-+ hc_regs = core_if->host_if->hc_regs[hc->hc_num];
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+ hc_set_even_odd_frame(core_if, hc, &hcchar);
-+ }
-+
-+ /* Load OUT packet into the appropriate Tx FIFO. */
-+ dwc_otg_hc_write_packet(core_if, hc);
-+ hc->requests++;
-+ return 1;
-+ } else {
-+ return 0;
-+ }
-+ }
-+}
-+
-+/**
-+ * Starts a PING transfer. This function should only be called in Slave mode.
-+ * The Do Ping bit is set in the HCTSIZ register, then the channel is enabled.
-+ */
-+void dwc_otg_hc_do_ping(dwc_otg_core_if_t * core_if, dwc_hc_t * hc)
-+{
-+ hcchar_data_t hcchar;
-+ hctsiz_data_t hctsiz;
-+ dwc_otg_hc_regs_t *hc_regs = core_if->host_if->hc_regs[hc->hc_num];
-+
-+ DWC_DEBUGPL(DBG_HCDV, "%s: Channel %d\n", __func__, hc->hc_num);
-+
-+ hctsiz.d32 = 0;
-+ hctsiz.b.dopng = 1;
-+ hctsiz.b.pktcnt = 1;
-+ DWC_WRITE_REG32(&hc_regs->hctsiz, hctsiz.d32);
-+
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+ hcchar.b.chen = 1;
-+ hcchar.b.chdis = 0;
-+ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32);
-+}
-+
-+/*
-+ * This function writes a packet into the Tx FIFO associated with the Host
-+ * Channel. For a channel associated with a non-periodic EP, the non-periodic
-+ * Tx FIFO is written. For a channel associated with a periodic EP, the
-+ * periodic Tx FIFO is written. This function should only be called in Slave
-+ * mode.
-+ *
-+ * Upon return the xfer_buff and xfer_count fields in _hc are incremented by
-+ * then number of bytes written to the Tx FIFO.
-+ */
-+void dwc_otg_hc_write_packet(dwc_otg_core_if_t * core_if, dwc_hc_t * hc)
-+{
-+ uint32_t i;
-+ uint32_t remaining_count;
-+ uint32_t byte_count;
-+ uint32_t dword_count;
-+
-+ uint32_t *data_buff = (uint32_t *) (hc->xfer_buff);
-+ uint32_t *data_fifo = core_if->data_fifo[hc->hc_num];
-+
-+ remaining_count = hc->xfer_len - hc->xfer_count;
-+ if (remaining_count > hc->max_packet) {
-+ byte_count = hc->max_packet;
-+ } else {
-+ byte_count = remaining_count;
-+ }
-+
-+ dword_count = (byte_count + 3) / 4;
-+
-+ if ((((unsigned long)data_buff) & 0x3) == 0) {
-+ /* xfer_buff is DWORD aligned. */
-+ for (i = 0; i < dword_count; i++, data_buff++) {
-+ DWC_WRITE_REG32(data_fifo, *data_buff);
-+ }
-+ } else {
-+ /* xfer_buff is not DWORD aligned. */
-+ for (i = 0; i < dword_count; i++, data_buff++) {
-+ uint32_t data;
-+ data =
-+ (data_buff[0] | data_buff[1] << 8 | data_buff[2] <<
-+ 16 | data_buff[3] << 24);
-+ DWC_WRITE_REG32(data_fifo, data);
-+ }
-+ }
-+
-+ hc->xfer_count += byte_count;
-+ hc->xfer_buff += byte_count;
-+}
-+
-+/**
-+ * Gets the current USB frame number. This is the frame number from the last
-+ * SOF packet.
-+ */
-+uint32_t dwc_otg_get_frame_number(dwc_otg_core_if_t * core_if)
-+{
-+ dsts_data_t dsts;
-+ dsts.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dsts);
-+
-+ /* read current frame/microframe number from DSTS register */
-+ return dsts.b.soffn;
-+}
-+
-+/**
-+ * Calculates and gets the frame Interval value of HFIR register according PHY
-+ * type and speed.The application can modify a value of HFIR register only after
-+ * the Port Enable bit of the Host Port Control and Status register
-+ * (HPRT.PrtEnaPort) has been set.
-+*/
-+
-+uint32_t calc_frame_interval(dwc_otg_core_if_t * core_if)
-+{
-+ gusbcfg_data_t usbcfg;
-+ hwcfg2_data_t hwcfg2;
-+ hprt0_data_t hprt0;
-+ int clock = 60; // default value
-+ usbcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->gusbcfg);
-+ hwcfg2.d32 = DWC_READ_REG32(&core_if->core_global_regs->ghwcfg2);
-+ hprt0.d32 = DWC_READ_REG32(core_if->host_if->hprt0);
-+ if (!usbcfg.b.physel && usbcfg.b.ulpi_utmi_sel && !usbcfg.b.phyif)
-+ clock = 60;
-+ if (usbcfg.b.physel && hwcfg2.b.fs_phy_type == 3)
-+ clock = 48;
-+ if (!usbcfg.b.phylpwrclksel && !usbcfg.b.physel &&
-+ !usbcfg.b.ulpi_utmi_sel && usbcfg.b.phyif)
-+ clock = 30;
-+ if (!usbcfg.b.phylpwrclksel && !usbcfg.b.physel &&
-+ !usbcfg.b.ulpi_utmi_sel && !usbcfg.b.phyif)
-+ clock = 60;
-+ if (usbcfg.b.phylpwrclksel && !usbcfg.b.physel &&
-+ !usbcfg.b.ulpi_utmi_sel && usbcfg.b.phyif)
-+ clock = 48;
-+ if (usbcfg.b.physel && !usbcfg.b.phyif && hwcfg2.b.fs_phy_type == 2)
-+ clock = 48;
-+ if (usbcfg.b.physel && hwcfg2.b.fs_phy_type == 1)
-+ clock = 48;
-+ if (hprt0.b.prtspd == 0)
-+ /* High speed case */
-+ return 125 * clock;
-+ else
-+ /* FS/LS case */
-+ return 1000 * clock;
-+}
-+
-+/**
-+ * This function reads a setup packet from the Rx FIFO into the destination
-+ * buffer. This function is called from the Rx Status Queue Level (RxStsQLvl)
-+ * Interrupt routine when a SETUP packet has been received in Slave mode.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param dest Destination buffer for packet data.
-+ */
-+void dwc_otg_read_setup_packet(dwc_otg_core_if_t * core_if, uint32_t * dest)
-+{
-+ device_grxsts_data_t status;
-+ /* Get the 8 bytes of a setup transaction data */
-+
-+ /* Pop 2 DWORDS off the receive data FIFO into memory */
-+ dest[0] = DWC_READ_REG32(core_if->data_fifo[0]);
-+ dest[1] = DWC_READ_REG32(core_if->data_fifo[0]);
-+ if (core_if->snpsid >= OTG_CORE_REV_3_00a) {
-+ status.d32 =
-+ DWC_READ_REG32(&core_if->core_global_regs->grxstsp);
-+ DWC_DEBUGPL(DBG_ANY,
-+ "EP:%d BCnt:%d " "pktsts:%x Frame:%d(0x%0x)\n",
-+ status.b.epnum, status.b.bcnt, status.b.pktsts,
-+ status.b.fn, status.b.fn);
-+ }
-+}
-+
-+/**
-+ * This function enables EP0 OUT to receive SETUP packets and configures EP0
-+ * IN for transmitting packets. It is normally called when the
-+ * "Enumeration Done" interrupt occurs.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param ep The EP0 data.
-+ */
-+void dwc_otg_ep0_activate(dwc_otg_core_if_t * core_if, dwc_ep_t * ep)
-+{
-+ dwc_otg_dev_if_t *dev_if = core_if->dev_if;
-+ dsts_data_t dsts;
-+ depctl_data_t diepctl;
-+ depctl_data_t doepctl;
-+ dctl_data_t dctl = {.d32 = 0 };
-+
-+ ep->stp_rollover = 0;
-+ /* Read the Device Status and Endpoint 0 Control registers */
-+ dsts.d32 = DWC_READ_REG32(&dev_if->dev_global_regs->dsts);
-+ diepctl.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[0]->diepctl);
-+ doepctl.d32 = DWC_READ_REG32(&dev_if->out_ep_regs[0]->doepctl);
-+
-+ /* Set the MPS of the IN EP based on the enumeration speed */
-+ switch (dsts.b.enumspd) {
-+ case DWC_DSTS_ENUMSPD_HS_PHY_30MHZ_OR_60MHZ:
-+ case DWC_DSTS_ENUMSPD_FS_PHY_30MHZ_OR_60MHZ:
-+ case DWC_DSTS_ENUMSPD_FS_PHY_48MHZ:
-+ diepctl.b.mps = DWC_DEP0CTL_MPS_64;
-+ break;
-+ case DWC_DSTS_ENUMSPD_LS_PHY_6MHZ:
-+ diepctl.b.mps = DWC_DEP0CTL_MPS_8;
-+ break;
-+ }
-+
-+ DWC_WRITE_REG32(&dev_if->in_ep_regs[0]->diepctl, diepctl.d32);
-+
-+ /* Enable OUT EP for receive */
-+ if (core_if->snpsid <= OTG_CORE_REV_2_94a) {
-+ doepctl.b.epena = 1;
-+ DWC_WRITE_REG32(&dev_if->out_ep_regs[0]->doepctl, doepctl.d32);
-+ }
-+#ifdef VERBOSE
-+ DWC_DEBUGPL(DBG_PCDV, "doepctl0=%0x\n",
-+ DWC_READ_REG32(&dev_if->out_ep_regs[0]->doepctl));
-+ DWC_DEBUGPL(DBG_PCDV, "diepctl0=%0x\n",
-+ DWC_READ_REG32(&dev_if->in_ep_regs[0]->diepctl));
-+#endif
-+ dctl.b.cgnpinnak = 1;
-+
-+ DWC_MODIFY_REG32(&dev_if->dev_global_regs->dctl, dctl.d32, dctl.d32);
-+ DWC_DEBUGPL(DBG_PCDV, "dctl=%0x\n",
-+ DWC_READ_REG32(&dev_if->dev_global_regs->dctl));
-+
-+}
-+
-+/**
-+ * This function activates an EP. The Device EP control register for
-+ * the EP is configured as defined in the ep structure. Note: This
-+ * function is not used for EP0.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param ep The EP to activate.
-+ */
-+void dwc_otg_ep_activate(dwc_otg_core_if_t * core_if, dwc_ep_t * ep)
-+{
-+ dwc_otg_dev_if_t *dev_if = core_if->dev_if;
-+ depctl_data_t depctl;
-+ volatile uint32_t *addr;
-+ daint_data_t daintmsk = {.d32 = 0 };
-+ dcfg_data_t dcfg;
-+ uint8_t i;
-+
-+ DWC_DEBUGPL(DBG_PCDV, "%s() EP%d-%s\n", __func__, ep->num,
-+ (ep->is_in ? "IN" : "OUT"));
-+
-+#ifdef DWC_UTE_PER_IO
-+ ep->xiso_frame_num = 0xFFFFFFFF;
-+ ep->xiso_active_xfers = 0;
-+ ep->xiso_queued_xfers = 0;
-+#endif
-+ /* Read DEPCTLn register */
-+ if (ep->is_in == 1) {
-+ addr = &dev_if->in_ep_regs[ep->num]->diepctl;
-+ daintmsk.ep.in = 1 << ep->num;
-+ } else {
-+ addr = &dev_if->out_ep_regs[ep->num]->doepctl;
-+ daintmsk.ep.out = 1 << ep->num;
-+ }
-+
-+ /* If the EP is already active don't change the EP Control
-+ * register. */
-+ depctl.d32 = DWC_READ_REG32(addr);
-+ if (!depctl.b.usbactep) {
-+ depctl.b.mps = ep->maxpacket;
-+ depctl.b.eptype = ep->type;
-+ depctl.b.txfnum = ep->tx_fifo_num;
-+
-+ if (ep->type == DWC_OTG_EP_TYPE_ISOC) {
-+ depctl.b.setd0pid = 1; // ???
-+ } else {
-+ depctl.b.setd0pid = 1;
-+ }
-+ depctl.b.usbactep = 1;
-+
-+ /* Update nextep_seq array and EPMSCNT in DCFG*/
-+ if (!(depctl.b.eptype & 1) && (ep->is_in == 1)) { // NP IN EP
-+ for (i = 0; i <= core_if->dev_if->num_in_eps; i++) {
-+ if (core_if->nextep_seq[i] == core_if->first_in_nextep_seq)
-+ break;
-+ }
-+ core_if->nextep_seq[i] = ep->num;
-+ core_if->nextep_seq[ep->num] = core_if->first_in_nextep_seq;
-+ depctl.b.nextep = core_if->nextep_seq[ep->num];
-+ dcfg.d32 = DWC_READ_REG32(&dev_if->dev_global_regs->dcfg);
-+ dcfg.b.epmscnt++;
-+ DWC_WRITE_REG32(&dev_if->dev_global_regs->dcfg, dcfg.d32);
-+
-+ DWC_DEBUGPL(DBG_PCDV,
-+ "%s first_in_nextep_seq= %2d; nextep_seq[]:\n",
-+ __func__, core_if->first_in_nextep_seq);
-+ for (i=0; i <= core_if->dev_if->num_in_eps; i++) {
-+ DWC_DEBUGPL(DBG_PCDV, "%2d\n",
-+ core_if->nextep_seq[i]);
-+ }
-+
-+ }
-+
-+
-+ DWC_WRITE_REG32(addr, depctl.d32);
-+ DWC_DEBUGPL(DBG_PCDV, "DEPCTL=%08x\n", DWC_READ_REG32(addr));
-+ }
-+
-+ /* Enable the Interrupt for this EP */
-+ if (core_if->multiproc_int_enable) {
-+ if (ep->is_in == 1) {
-+ diepmsk_data_t diepmsk = {.d32 = 0 };
-+ diepmsk.b.xfercompl = 1;
-+ diepmsk.b.timeout = 1;
-+ diepmsk.b.epdisabled = 1;
-+ diepmsk.b.ahberr = 1;
-+ diepmsk.b.intknepmis = 1;
-+ if (!core_if->en_multiple_tx_fifo && core_if->dma_enable)
-+ diepmsk.b.intknepmis = 0;
-+ diepmsk.b.txfifoundrn = 1; //?????
-+ if (ep->type == DWC_OTG_EP_TYPE_ISOC) {
-+ diepmsk.b.nak = 1;
-+ }
-+
-+
-+
-+/*
-+ if (core_if->dma_desc_enable) {
-+ diepmsk.b.bna = 1;
-+ }
-+*/
-+/*
-+ if (core_if->dma_enable) {
-+ doepmsk.b.nak = 1;
-+ }
-+*/
-+ DWC_WRITE_REG32(&dev_if->dev_global_regs->
-+ diepeachintmsk[ep->num], diepmsk.d32);
-+
-+ } else {
-+ doepmsk_data_t doepmsk = {.d32 = 0 };
-+ doepmsk.b.xfercompl = 1;
-+ doepmsk.b.ahberr = 1;
-+ doepmsk.b.epdisabled = 1;
-+ if (ep->type == DWC_OTG_EP_TYPE_ISOC)
-+ doepmsk.b.outtknepdis = 1;
-+
-+/*
-+
-+ if (core_if->dma_desc_enable) {
-+ doepmsk.b.bna = 1;
-+ }
-+*/
-+/*
-+ doepmsk.b.babble = 1;
-+ doepmsk.b.nyet = 1;
-+ doepmsk.b.nak = 1;
-+*/
-+ DWC_WRITE_REG32(&dev_if->dev_global_regs->
-+ doepeachintmsk[ep->num], doepmsk.d32);
-+ }
-+ DWC_MODIFY_REG32(&dev_if->dev_global_regs->deachintmsk,
-+ 0, daintmsk.d32);
-+ } else {
-+ if (ep->type == DWC_OTG_EP_TYPE_ISOC) {
-+ if (ep->is_in) {
-+ diepmsk_data_t diepmsk = {.d32 = 0 };
-+ diepmsk.b.nak = 1;
-+ DWC_MODIFY_REG32(&dev_if->dev_global_regs->diepmsk, 0, diepmsk.d32);
-+ } else {
-+ doepmsk_data_t doepmsk = {.d32 = 0 };
-+ doepmsk.b.outtknepdis = 1;
-+ DWC_MODIFY_REG32(&dev_if->dev_global_regs->doepmsk, 0, doepmsk.d32);
-+ }
-+ }
-+ DWC_MODIFY_REG32(&dev_if->dev_global_regs->daintmsk,
-+ 0, daintmsk.d32);
-+ }
-+
-+ DWC_DEBUGPL(DBG_PCDV, "DAINTMSK=%0x\n",
-+ DWC_READ_REG32(&dev_if->dev_global_regs->daintmsk));
-+
-+ ep->stall_clear_flag = 0;
-+
-+ return;
-+}
-+
-+/**
-+ * This function deactivates an EP. This is done by clearing the USB Active
-+ * EP bit in the Device EP control register. Note: This function is not used
-+ * for EP0. EP0 cannot be deactivated.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param ep The EP to deactivate.
-+ */
-+void dwc_otg_ep_deactivate(dwc_otg_core_if_t * core_if, dwc_ep_t * ep)
-+{
-+ depctl_data_t depctl = {.d32 = 0 };
-+ volatile uint32_t *addr;
-+ daint_data_t daintmsk = {.d32 = 0 };
-+ dcfg_data_t dcfg;
-+ uint8_t i = 0;
-+
-+#ifdef DWC_UTE_PER_IO
-+ ep->xiso_frame_num = 0xFFFFFFFF;
-+ ep->xiso_active_xfers = 0;
-+ ep->xiso_queued_xfers = 0;
-+#endif
-+
-+ /* Read DEPCTLn register */
-+ if (ep->is_in == 1) {
-+ addr = &core_if->dev_if->in_ep_regs[ep->num]->diepctl;
-+ daintmsk.ep.in = 1 << ep->num;
-+ } else {
-+ addr = &core_if->dev_if->out_ep_regs[ep->num]->doepctl;
-+ daintmsk.ep.out = 1 << ep->num;
-+ }
-+
-+ depctl.d32 = DWC_READ_REG32(addr);
-+
-+ depctl.b.usbactep = 0;
-+
-+ /* Update nextep_seq array and EPMSCNT in DCFG*/
-+ if (!(depctl.b.eptype & 1) && ep->is_in == 1) { // NP EP IN
-+ for (i = 0; i <= core_if->dev_if->num_in_eps; i++) {
-+ if (core_if->nextep_seq[i] == ep->num)
-+ break;
-+ }
-+ core_if->nextep_seq[i] = core_if->nextep_seq[ep->num];
-+ if (core_if->first_in_nextep_seq == ep->num)
-+ core_if->first_in_nextep_seq = i;
-+ core_if->nextep_seq[ep->num] = 0xff;
-+ depctl.b.nextep = 0;
-+ dcfg.d32 =
-+ DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dcfg);
-+ dcfg.b.epmscnt--;
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dcfg,
-+ dcfg.d32);
-+
-+ DWC_DEBUGPL(DBG_PCDV,
-+ "%s first_in_nextep_seq= %2d; nextep_seq[]:\n",
-+ __func__, core_if->first_in_nextep_seq);
-+ for (i=0; i <= core_if->dev_if->num_in_eps; i++) {
-+ DWC_DEBUGPL(DBG_PCDV, "%2d\n", core_if->nextep_seq[i]);
-+ }
-+ }
-+
-+ if (ep->is_in == 1)
-+ depctl.b.txfnum = 0;
-+
-+ if (core_if->dma_desc_enable)
-+ depctl.b.epdis = 1;
-+
-+ DWC_WRITE_REG32(addr, depctl.d32);
-+ depctl.d32 = DWC_READ_REG32(addr);
-+ if (core_if->dma_enable && ep->type == DWC_OTG_EP_TYPE_ISOC
-+ && depctl.b.epena) {
-+ depctl_data_t depctl = {.d32 = 0};
-+ if (ep->is_in) {
-+ diepint_data_t diepint = {.d32 = 0};
-+
-+ depctl.b.snak = 1;
-+ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[ep->num]->
-+ diepctl, depctl.d32);
-+ do {
-+ dwc_udelay(10);
-+ diepint.d32 =
-+ DWC_READ_REG32(&core_if->
-+ dev_if->in_ep_regs[ep->num]->
-+ diepint);
-+ } while (!diepint.b.inepnakeff);
-+ diepint.b.inepnakeff = 1;
-+ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[ep->num]->
-+ diepint, diepint.d32);
-+ depctl.d32 = 0;
-+ depctl.b.epdis = 1;
-+ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[ep->num]->
-+ diepctl, depctl.d32);
-+ do {
-+ dwc_udelay(10);
-+ diepint.d32 =
-+ DWC_READ_REG32(&core_if->
-+ dev_if->in_ep_regs[ep->num]->
-+ diepint);
-+ } while (!diepint.b.epdisabled);
-+ diepint.b.epdisabled = 1;
-+ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[ep->num]->
-+ diepint, diepint.d32);
-+ } else {
-+ dctl_data_t dctl = {.d32 = 0};
-+ gintmsk_data_t gintsts = {.d32 = 0};
-+ doepint_data_t doepint = {.d32 = 0};
-+ dctl.b.sgoutnak = 1;
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->
-+ dctl, 0, dctl.d32);
-+ do {
-+ dwc_udelay(10);
-+ gintsts.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintsts);
-+ } while (!gintsts.b.goutnakeff);
-+ gintsts.d32 = 0;
-+ gintsts.b.goutnakeff = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32);
-+
-+ depctl.d32 = 0;
-+ depctl.b.epdis = 1;
-+ depctl.b.snak = 1;
-+ DWC_WRITE_REG32(&core_if->dev_if->out_ep_regs[ep->num]->doepctl, depctl.d32);
-+ do
-+ {
-+ dwc_udelay(10);
-+ doepint.d32 = DWC_READ_REG32(&core_if->dev_if->
-+ out_ep_regs[ep->num]->doepint);
-+ } while (!doepint.b.epdisabled);
-+
-+ doepint.b.epdisabled = 1;
-+ DWC_WRITE_REG32(&core_if->dev_if->out_ep_regs[ep->num]->doepint, doepint.d32);
-+
-+ dctl.d32 = 0;
-+ dctl.b.cgoutnak = 1;
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl, 0, dctl.d32);
-+ }
-+ }
-+
-+ /* Disable the Interrupt for this EP */
-+ if (core_if->multiproc_int_enable) {
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->deachintmsk,
-+ daintmsk.d32, 0);
-+
-+ if (ep->is_in == 1) {
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->
-+ diepeachintmsk[ep->num], 0);
-+ } else {
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->
-+ doepeachintmsk[ep->num], 0);
-+ }
-+ } else {
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->daintmsk,
-+ daintmsk.d32, 0);
-+ }
-+
-+}
-+
-+/**
-+ * This function initializes dma descriptor chain.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param ep The EP to start the transfer on.
-+ */
-+static void init_dma_desc_chain(dwc_otg_core_if_t * core_if, dwc_ep_t * ep)
-+{
-+ dwc_otg_dev_dma_desc_t *dma_desc;
-+ uint32_t offset;
-+ uint32_t xfer_est;
-+ int i;
-+ unsigned maxxfer_local, total_len;
-+
-+ if (!ep->is_in && ep->type == DWC_OTG_EP_TYPE_INTR &&
-+ (ep->maxpacket%4)) {
-+ maxxfer_local = ep->maxpacket;
-+ total_len = ep->xfer_len;
-+ } else {
-+ maxxfer_local = ep->maxxfer;
-+ total_len = ep->total_len;
-+ }
-+
-+ ep->desc_cnt = (total_len / maxxfer_local) +
-+ ((total_len % maxxfer_local) ? 1 : 0);
-+
-+ if (!ep->desc_cnt)
-+ ep->desc_cnt = 1;
-+
-+ if (ep->desc_cnt > MAX_DMA_DESC_CNT)
-+ ep->desc_cnt = MAX_DMA_DESC_CNT;
-+
-+ dma_desc = ep->desc_addr;
-+ if (maxxfer_local == ep->maxpacket) {
-+ if ((total_len % maxxfer_local) &&
-+ (total_len/maxxfer_local < MAX_DMA_DESC_CNT)) {
-+ xfer_est = (ep->desc_cnt - 1) * maxxfer_local +
-+ (total_len % maxxfer_local);
-+ } else
-+ xfer_est = ep->desc_cnt * maxxfer_local;
-+ } else
-+ xfer_est = total_len;
-+ offset = 0;
-+ for (i = 0; i < ep->desc_cnt; ++i) {
-+ /** DMA Descriptor Setup */
-+ if (xfer_est > maxxfer_local) {
-+ dma_desc->status.b.bs = BS_HOST_BUSY;
-+ dma_desc->status.b.l = 0;
-+ dma_desc->status.b.ioc = 0;
-+ dma_desc->status.b.sp = 0;
-+ dma_desc->status.b.bytes = maxxfer_local;
-+ dma_desc->buf = ep->dma_addr + offset;
-+ dma_desc->status.b.sts = 0;
-+ dma_desc->status.b.bs = BS_HOST_READY;
-+
-+ xfer_est -= maxxfer_local;
-+ offset += maxxfer_local;
-+ } else {
-+ dma_desc->status.b.bs = BS_HOST_BUSY;
-+ dma_desc->status.b.l = 1;
-+ dma_desc->status.b.ioc = 1;
-+ if (ep->is_in) {
-+ dma_desc->status.b.sp =
-+ (xfer_est %
-+ ep->maxpacket) ? 1 : ((ep->
-+ sent_zlp) ? 1 : 0);
-+ dma_desc->status.b.bytes = xfer_est;
-+ } else {
-+ if (maxxfer_local == ep->maxpacket)
-+ dma_desc->status.b.bytes = xfer_est;
-+ else
-+ dma_desc->status.b.bytes =
-+ xfer_est + ((4 - (xfer_est & 0x3)) & 0x3);
-+ }
-+
-+ dma_desc->buf = ep->dma_addr + offset;
-+ dma_desc->status.b.sts = 0;
-+ dma_desc->status.b.bs = BS_HOST_READY;
-+ }
-+ dma_desc++;
-+ }
-+}
-+/**
-+ * This function is called when to write ISOC data into appropriate dedicated
-+ * periodic FIFO.
-+ */
-+static int32_t write_isoc_tx_fifo(dwc_otg_core_if_t * core_if, dwc_ep_t * dwc_ep)
-+{
-+ dwc_otg_dev_if_t *dev_if = core_if->dev_if;
-+ dwc_otg_dev_in_ep_regs_t *ep_regs;
-+ dtxfsts_data_t txstatus = {.d32 = 0 };
-+ uint32_t len = 0;
-+ int epnum = dwc_ep->num;
-+ int dwords;
-+
-+ DWC_DEBUGPL(DBG_PCD, "Dedicated TxFifo Empty: %d \n", epnum);
-+
-+ ep_regs = core_if->dev_if->in_ep_regs[epnum];
-+
-+ len = dwc_ep->xfer_len - dwc_ep->xfer_count;
-+
-+ if (len > dwc_ep->maxpacket) {
-+ len = dwc_ep->maxpacket;
-+ }
-+
-+ dwords = (len + 3) / 4;
-+
-+ /* While there is space in the queue and space in the FIFO and
-+ * More data to tranfer, Write packets to the Tx FIFO */
-+ txstatus.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[epnum]->dtxfsts);
-+ DWC_DEBUGPL(DBG_PCDV, "b4 dtxfsts[%d]=0x%08x\n", epnum, txstatus.d32);
-+
-+ while (txstatus.b.txfspcavail > dwords &&
-+ dwc_ep->xfer_count < dwc_ep->xfer_len && dwc_ep->xfer_len != 0) {
-+ /* Write the FIFO */
-+ dwc_otg_ep_write_packet(core_if, dwc_ep, 0);
-+
-+ len = dwc_ep->xfer_len - dwc_ep->xfer_count;
-+ if (len > dwc_ep->maxpacket) {
-+ len = dwc_ep->maxpacket;
-+ }
-+
-+ dwords = (len + 3) / 4;
-+ txstatus.d32 =
-+ DWC_READ_REG32(&dev_if->in_ep_regs[epnum]->dtxfsts);
-+ DWC_DEBUGPL(DBG_PCDV, "dtxfsts[%d]=0x%08x\n", epnum,
-+ txstatus.d32);
-+ }
-+
-+ DWC_DEBUGPL(DBG_PCDV, "b4 dtxfsts[%d]=0x%08x\n", epnum,
-+ DWC_READ_REG32(&dev_if->in_ep_regs[epnum]->dtxfsts));
-+
-+ return 1;
-+}
-+/**
-+ * This function does the setup for a data transfer for an EP and
-+ * starts the transfer. For an IN transfer, the packets will be
-+ * loaded into the appropriate Tx FIFO in the ISR. For OUT transfers,
-+ * the packets are unloaded from the Rx FIFO in the ISR. the ISR.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param ep The EP to start the transfer on.
-+ */
-+
-+void dwc_otg_ep_start_transfer(dwc_otg_core_if_t * core_if, dwc_ep_t * ep)
-+{
-+ depctl_data_t depctl;
-+ deptsiz_data_t deptsiz;
-+ gintmsk_data_t intr_mask = {.d32 = 0 };
-+
-+ DWC_DEBUGPL((DBG_PCDV | DBG_CILV), "%s()\n", __func__);
-+ DWC_DEBUGPL(DBG_PCD, "ep%d-%s xfer_len=%d xfer_cnt=%d "
-+ "xfer_buff=%p start_xfer_buff=%p, total_len = %d\n",
-+ ep->num, (ep->is_in ? "IN" : "OUT"), ep->xfer_len,
-+ ep->xfer_count, ep->xfer_buff, ep->start_xfer_buff,
-+ ep->total_len);
-+ /* IN endpoint */
-+ if (ep->is_in == 1) {
-+ dwc_otg_dev_in_ep_regs_t *in_regs =
-+ core_if->dev_if->in_ep_regs[ep->num];
-+
-+ gnptxsts_data_t gtxstatus;
-+
-+ gtxstatus.d32 =
-+ DWC_READ_REG32(&core_if->core_global_regs->gnptxsts);
-+
-+ if (core_if->en_multiple_tx_fifo == 0
-+ && gtxstatus.b.nptxqspcavail == 0 && !core_if->dma_enable) {
-+#ifdef DEBUG
-+ DWC_PRINTF("TX Queue Full (0x%0x)\n", gtxstatus.d32);
-+#endif
-+ return;
-+ }
-+
-+ depctl.d32 = DWC_READ_REG32(&(in_regs->diepctl));
-+ deptsiz.d32 = DWC_READ_REG32(&(in_regs->dieptsiz));
-+
-+ if (ep->maxpacket > ep->maxxfer / MAX_PKT_CNT)
-+ ep->xfer_len += (ep->maxxfer < (ep->total_len - ep->xfer_len)) ?
-+ ep->maxxfer : (ep->total_len - ep->xfer_len);
-+ else
-+ ep->xfer_len += (MAX_PKT_CNT * ep->maxpacket < (ep->total_len - ep->xfer_len)) ?
-+ MAX_PKT_CNT * ep->maxpacket : (ep->total_len - ep->xfer_len);
-+
-+
-+ /* Zero Length Packet? */
-+ if ((ep->xfer_len - ep->xfer_count) == 0) {
-+ deptsiz.b.xfersize = 0;
-+ deptsiz.b.pktcnt = 1;
-+ } else {
-+ /* Program the transfer size and packet count
-+ * as follows: xfersize = N * maxpacket +
-+ * short_packet pktcnt = N + (short_packet
-+ * exist ? 1 : 0)
-+ */
-+ deptsiz.b.xfersize = ep->xfer_len - ep->xfer_count;
-+ deptsiz.b.pktcnt =
-+ (ep->xfer_len - ep->xfer_count - 1 +
-+ ep->maxpacket) / ep->maxpacket;
-+ if (deptsiz.b.pktcnt > MAX_PKT_CNT) {
-+ deptsiz.b.pktcnt = MAX_PKT_CNT;
-+ deptsiz.b.xfersize = deptsiz.b.pktcnt * ep->maxpacket;
-+ }
-+ if (ep->type == DWC_OTG_EP_TYPE_ISOC)
-+ deptsiz.b.mc = deptsiz.b.pktcnt;
-+ }
-+
-+ /* Write the DMA register */
-+ if (core_if->dma_enable) {
-+ if (core_if->dma_desc_enable == 0) {
-+ if (ep->type != DWC_OTG_EP_TYPE_ISOC)
-+ deptsiz.b.mc = 1;
-+ DWC_WRITE_REG32(&in_regs->dieptsiz,
-+ deptsiz.d32);
-+ DWC_WRITE_REG32(&(in_regs->diepdma),
-+ (uint32_t) ep->dma_addr);
-+ } else {
-+#ifdef DWC_UTE_CFI
-+ /* The descriptor chain should be already initialized by now */
-+ if (ep->buff_mode != BM_STANDARD) {
-+ DWC_WRITE_REG32(&in_regs->diepdma,
-+ ep->descs_dma_addr);
-+ } else {
-+#endif
-+ init_dma_desc_chain(core_if, ep);
-+ /** DIEPDMAn Register write */
-+ DWC_WRITE_REG32(&in_regs->diepdma,
-+ ep->dma_desc_addr);
-+#ifdef DWC_UTE_CFI
-+ }
-+#endif
-+ }
-+ } else {
-+ DWC_WRITE_REG32(&in_regs->dieptsiz, deptsiz.d32);
-+ if (ep->type != DWC_OTG_EP_TYPE_ISOC) {
-+ /**
-+ * Enable the Non-Periodic Tx FIFO empty interrupt,
-+ * or the Tx FIFO epmty interrupt in dedicated Tx FIFO mode,
-+ * the data will be written into the fifo by the ISR.
-+ */
-+ if (core_if->en_multiple_tx_fifo == 0) {
-+ intr_mask.b.nptxfempty = 1;
-+ DWC_MODIFY_REG32
-+ (&core_if->core_global_regs->gintmsk,
-+ intr_mask.d32, intr_mask.d32);
-+ } else {
-+ /* Enable the Tx FIFO Empty Interrupt for this EP */
-+ if (ep->xfer_len > 0) {
-+ uint32_t fifoemptymsk = 0;
-+ fifoemptymsk = 1 << ep->num;
-+ DWC_MODIFY_REG32
-+ (&core_if->dev_if->dev_global_regs->dtknqr4_fifoemptymsk,
-+ 0, fifoemptymsk);
-+
-+ }
-+ }
-+ } else {
-+ write_isoc_tx_fifo(core_if, ep);
-+ }
-+ }
-+ if (!core_if->core_params->en_multiple_tx_fifo && core_if->dma_enable)
-+ depctl.b.nextep = core_if->nextep_seq[ep->num];
-+
-+ if (ep->type == DWC_OTG_EP_TYPE_ISOC) {
-+ dsts_data_t dsts = {.d32 = 0};
-+ if (ep->bInterval == 1) {
-+ dsts.d32 =
-+ DWC_READ_REG32(&core_if->dev_if->
-+ dev_global_regs->dsts);
-+ ep->frame_num = dsts.b.soffn + ep->bInterval;
-+ if (ep->frame_num > 0x3FFF) {
-+ ep->frm_overrun = 1;
-+ ep->frame_num &= 0x3FFF;
-+ } else
-+ ep->frm_overrun = 0;
-+ if (ep->frame_num & 0x1) {
-+ depctl.b.setd1pid = 1;
-+ } else {
-+ depctl.b.setd0pid = 1;
-+ }
-+ }
-+ }
-+ /* EP enable, IN data in FIFO */
-+ depctl.b.cnak = 1;
-+ depctl.b.epena = 1;
-+ DWC_WRITE_REG32(&in_regs->diepctl, depctl.d32);
-+
-+ } else {
-+ /* OUT endpoint */
-+ dwc_otg_dev_out_ep_regs_t *out_regs =
-+ core_if->dev_if->out_ep_regs[ep->num];
-+
-+ depctl.d32 = DWC_READ_REG32(&(out_regs->doepctl));
-+ deptsiz.d32 = DWC_READ_REG32(&(out_regs->doeptsiz));
-+
-+ if (!core_if->dma_desc_enable) {
-+ if (ep->maxpacket > ep->maxxfer / MAX_PKT_CNT)
-+ ep->xfer_len += (ep->maxxfer < (ep->total_len - ep->xfer_len)) ?
-+ ep->maxxfer : (ep->total_len - ep->xfer_len);
-+ else
-+ ep->xfer_len += (MAX_PKT_CNT * ep->maxpacket < (ep->total_len
-+ - ep->xfer_len)) ? MAX_PKT_CNT * ep->maxpacket : (ep->total_len - ep->xfer_len);
-+ }
-+
-+ /* Program the transfer size and packet count as follows:
-+ *
-+ * pktcnt = N
-+ * xfersize = N * maxpacket
-+ */
-+ if ((ep->xfer_len - ep->xfer_count) == 0) {
-+ /* Zero Length Packet */
-+ deptsiz.b.xfersize = ep->maxpacket;
-+ deptsiz.b.pktcnt = 1;
-+ } else {
-+ deptsiz.b.pktcnt =
-+ (ep->xfer_len - ep->xfer_count +
-+ (ep->maxpacket - 1)) / ep->maxpacket;
-+ if (deptsiz.b.pktcnt > MAX_PKT_CNT) {
-+ deptsiz.b.pktcnt = MAX_PKT_CNT;
-+ }
-+ if (!core_if->dma_desc_enable) {
-+ ep->xfer_len =
-+ deptsiz.b.pktcnt * ep->maxpacket + ep->xfer_count;
-+ }
-+ deptsiz.b.xfersize = ep->xfer_len - ep->xfer_count;
-+ }
-+
-+ DWC_DEBUGPL(DBG_PCDV, "ep%d xfersize=%d pktcnt=%d\n",
-+ ep->num, deptsiz.b.xfersize, deptsiz.b.pktcnt);
-+
-+ if (core_if->dma_enable) {
-+ if (!core_if->dma_desc_enable) {
-+ DWC_WRITE_REG32(&out_regs->doeptsiz,
-+ deptsiz.d32);
-+
-+ DWC_WRITE_REG32(&(out_regs->doepdma),
-+ (uint32_t) ep->dma_addr);
-+ } else {
-+#ifdef DWC_UTE_CFI
-+ /* The descriptor chain should be already initialized by now */
-+ if (ep->buff_mode != BM_STANDARD) {
-+ DWC_WRITE_REG32(&out_regs->doepdma,
-+ ep->descs_dma_addr);
-+ } else {
-+#endif
-+ /** This is used for interrupt out transfers*/
-+ if (!ep->xfer_len)
-+ ep->xfer_len = ep->total_len;
-+ init_dma_desc_chain(core_if, ep);
-+
-+ if (core_if->core_params->dev_out_nak) {
-+ if (ep->type == DWC_OTG_EP_TYPE_BULK) {
-+ deptsiz.b.pktcnt = (ep->total_len +
-+ (ep->maxpacket - 1)) / ep->maxpacket;
-+ deptsiz.b.xfersize = ep->total_len;
-+ /* Remember initial value of doeptsiz */
-+ core_if->start_doeptsiz_val[ep->num] = deptsiz.d32;
-+ DWC_WRITE_REG32(&out_regs->doeptsiz,
-+ deptsiz.d32);
-+ }
-+ }
-+ /** DOEPDMAn Register write */
-+ DWC_WRITE_REG32(&out_regs->doepdma,
-+ ep->dma_desc_addr);
-+#ifdef DWC_UTE_CFI
-+ }
-+#endif
-+ }
-+ } else {
-+ DWC_WRITE_REG32(&out_regs->doeptsiz, deptsiz.d32);
-+ }
-+
-+ if (ep->type == DWC_OTG_EP_TYPE_ISOC) {
-+ dsts_data_t dsts = {.d32 = 0};
-+ if (ep->bInterval == 1) {
-+ dsts.d32 =
-+ DWC_READ_REG32(&core_if->dev_if->
-+ dev_global_regs->dsts);
-+ ep->frame_num = dsts.b.soffn + ep->bInterval;
-+ if (ep->frame_num > 0x3FFF) {
-+ ep->frm_overrun = 1;
-+ ep->frame_num &= 0x3FFF;
-+ } else
-+ ep->frm_overrun = 0;
-+
-+ if (ep->frame_num & 0x1) {
-+ depctl.b.setd1pid = 1;
-+ } else {
-+ depctl.b.setd0pid = 1;
-+ }
-+ }
-+ }
-+
-+ /* EP enable */
-+ depctl.b.cnak = 1;
-+ depctl.b.epena = 1;
-+
-+ DWC_WRITE_REG32(&out_regs->doepctl, depctl.d32);
-+
-+ DWC_DEBUGPL(DBG_PCD, "DOEPCTL=%08x DOEPTSIZ=%08x\n",
-+ DWC_READ_REG32(&out_regs->doepctl),
-+ DWC_READ_REG32(&out_regs->doeptsiz));
-+ DWC_DEBUGPL(DBG_PCD, "DAINTMSK=%08x GINTMSK=%08x\n",
-+ DWC_READ_REG32(&core_if->dev_if->dev_global_regs->
-+ daintmsk),
-+ DWC_READ_REG32(&core_if->core_global_regs->
-+ gintmsk));
-+
-+ /* Timer is scheduling only for out bulk transfers for
-+ * "Device DDMA OUT NAK Enhancement" feature to inform user
-+ * about received data payload in case of timeout
-+ */
-+ if (core_if->core_params->dev_out_nak) {
-+ if (ep->type == DWC_OTG_EP_TYPE_BULK) {
-+ core_if->ep_xfer_info[ep->num].core_if = core_if;
-+ core_if->ep_xfer_info[ep->num].ep = ep;
-+ core_if->ep_xfer_info[ep->num].state = 1;
-+
-+ /* Start a timer for this transfer. */
-+ DWC_TIMER_SCHEDULE(core_if->ep_xfer_timer[ep->num], 10000);
-+ }
-+ }
-+ }
-+}
-+
-+/**
-+ * This function setup a zero length transfer in Buffer DMA and
-+ * Slave modes for usb requests with zero field set
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param ep The EP to start the transfer on.
-+ *
-+ */
-+void dwc_otg_ep_start_zl_transfer(dwc_otg_core_if_t * core_if, dwc_ep_t * ep)
-+{
-+
-+ depctl_data_t depctl;
-+ deptsiz_data_t deptsiz;
-+ gintmsk_data_t intr_mask = {.d32 = 0 };
-+
-+ DWC_DEBUGPL((DBG_PCDV | DBG_CILV), "%s()\n", __func__);
-+ DWC_PRINTF("zero length transfer is called\n");
-+
-+ /* IN endpoint */
-+ if (ep->is_in == 1) {
-+ dwc_otg_dev_in_ep_regs_t *in_regs =
-+ core_if->dev_if->in_ep_regs[ep->num];
-+
-+ depctl.d32 = DWC_READ_REG32(&(in_regs->diepctl));
-+ deptsiz.d32 = DWC_READ_REG32(&(in_regs->dieptsiz));
-+
-+ deptsiz.b.xfersize = 0;
-+ deptsiz.b.pktcnt = 1;
-+
-+ /* Write the DMA register */
-+ if (core_if->dma_enable) {
-+ if (core_if->dma_desc_enable == 0) {
-+ deptsiz.b.mc = 1;
-+ DWC_WRITE_REG32(&in_regs->dieptsiz,
-+ deptsiz.d32);
-+ DWC_WRITE_REG32(&(in_regs->diepdma),
-+ (uint32_t) ep->dma_addr);
-+ }
-+ } else {
-+ DWC_WRITE_REG32(&in_regs->dieptsiz, deptsiz.d32);
-+ /**
-+ * Enable the Non-Periodic Tx FIFO empty interrupt,
-+ * or the Tx FIFO epmty interrupt in dedicated Tx FIFO mode,
-+ * the data will be written into the fifo by the ISR.
-+ */
-+ if (core_if->en_multiple_tx_fifo == 0) {
-+ intr_mask.b.nptxfempty = 1;
-+ DWC_MODIFY_REG32(&core_if->
-+ core_global_regs->gintmsk,
-+ intr_mask.d32, intr_mask.d32);
-+ } else {
-+ /* Enable the Tx FIFO Empty Interrupt for this EP */
-+ if (ep->xfer_len > 0) {
-+ uint32_t fifoemptymsk = 0;
-+ fifoemptymsk = 1 << ep->num;
-+ DWC_MODIFY_REG32(&core_if->
-+ dev_if->dev_global_regs->dtknqr4_fifoemptymsk,
-+ 0, fifoemptymsk);
-+ }
-+ }
-+ }
-+
-+ if (!core_if->core_params->en_multiple_tx_fifo && core_if->dma_enable)
-+ depctl.b.nextep = core_if->nextep_seq[ep->num];
-+ /* EP enable, IN data in FIFO */
-+ depctl.b.cnak = 1;
-+ depctl.b.epena = 1;
-+ DWC_WRITE_REG32(&in_regs->diepctl, depctl.d32);
-+
-+ } else {
-+ /* OUT endpoint */
-+ dwc_otg_dev_out_ep_regs_t *out_regs =
-+ core_if->dev_if->out_ep_regs[ep->num];
-+
-+ depctl.d32 = DWC_READ_REG32(&(out_regs->doepctl));
-+ deptsiz.d32 = DWC_READ_REG32(&(out_regs->doeptsiz));
-+
-+ /* Zero Length Packet */
-+ deptsiz.b.xfersize = ep->maxpacket;
-+ deptsiz.b.pktcnt = 1;
-+
-+ if (core_if->dma_enable) {
-+ if (!core_if->dma_desc_enable) {
-+ DWC_WRITE_REG32(&out_regs->doeptsiz,
-+ deptsiz.d32);
-+
-+ DWC_WRITE_REG32(&(out_regs->doepdma),
-+ (uint32_t) ep->dma_addr);
-+ }
-+ } else {
-+ DWC_WRITE_REG32(&out_regs->doeptsiz, deptsiz.d32);
-+ }
-+
-+ /* EP enable */
-+ depctl.b.cnak = 1;
-+ depctl.b.epena = 1;
-+
-+ DWC_WRITE_REG32(&out_regs->doepctl, depctl.d32);
-+
-+ }
-+}
-+
-+/**
-+ * This function does the setup for a data transfer for EP0 and starts
-+ * the transfer. For an IN transfer, the packets will be loaded into
-+ * the appropriate Tx FIFO in the ISR. For OUT transfers, the packets are
-+ * unloaded from the Rx FIFO in the ISR.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param ep The EP0 data.
-+ */
-+void dwc_otg_ep0_start_transfer(dwc_otg_core_if_t * core_if, dwc_ep_t * ep)
-+{
-+ depctl_data_t depctl;
-+ deptsiz0_data_t deptsiz;
-+ gintmsk_data_t intr_mask = {.d32 = 0 };
-+ dwc_otg_dev_dma_desc_t *dma_desc;
-+
-+ DWC_DEBUGPL(DBG_PCD, "ep%d-%s xfer_len=%d xfer_cnt=%d "
-+ "xfer_buff=%p start_xfer_buff=%p \n",
-+ ep->num, (ep->is_in ? "IN" : "OUT"), ep->xfer_len,
-+ ep->xfer_count, ep->xfer_buff, ep->start_xfer_buff);
-+
-+ ep->total_len = ep->xfer_len;
-+
-+ /* IN endpoint */
-+ if (ep->is_in == 1) {
-+ dwc_otg_dev_in_ep_regs_t *in_regs =
-+ core_if->dev_if->in_ep_regs[0];
-+
-+ gnptxsts_data_t gtxstatus;
-+
-+ if (core_if->snpsid >= OTG_CORE_REV_3_00a) {
-+ depctl.d32 = DWC_READ_REG32(&in_regs->diepctl);
-+ if (depctl.b.epena)
-+ return;
-+ }
-+
-+ gtxstatus.d32 =
-+ DWC_READ_REG32(&core_if->core_global_regs->gnptxsts);
-+
-+ /* If dedicated FIFO every time flush fifo before enable ep*/
-+ if (core_if->en_multiple_tx_fifo && core_if->snpsid >= OTG_CORE_REV_3_00a)
-+ dwc_otg_flush_tx_fifo(core_if, ep->tx_fifo_num);
-+
-+ if (core_if->en_multiple_tx_fifo == 0
-+ && gtxstatus.b.nptxqspcavail == 0
-+ && !core_if->dma_enable) {
-+#ifdef DEBUG
-+ deptsiz.d32 = DWC_READ_REG32(&in_regs->dieptsiz);
-+ DWC_DEBUGPL(DBG_PCD, "DIEPCTL0=%0x\n",
-+ DWC_READ_REG32(&in_regs->diepctl));
-+ DWC_DEBUGPL(DBG_PCD, "DIEPTSIZ0=%0x (sz=%d, pcnt=%d)\n",
-+ deptsiz.d32,
-+ deptsiz.b.xfersize, deptsiz.b.pktcnt);
-+ DWC_PRINTF("TX Queue or FIFO Full (0x%0x)\n",
-+ gtxstatus.d32);
-+#endif
-+ return;
-+ }
-+
-+ depctl.d32 = DWC_READ_REG32(&in_regs->diepctl);
-+ deptsiz.d32 = DWC_READ_REG32(&in_regs->dieptsiz);
-+
-+ /* Zero Length Packet? */
-+ if (ep->xfer_len == 0) {
-+ deptsiz.b.xfersize = 0;
-+ deptsiz.b.pktcnt = 1;
-+ } else {
-+ /* Program the transfer size and packet count
-+ * as follows: xfersize = N * maxpacket +
-+ * short_packet pktcnt = N + (short_packet
-+ * exist ? 1 : 0)
-+ */
-+ if (ep->xfer_len > ep->maxpacket) {
-+ ep->xfer_len = ep->maxpacket;
-+ deptsiz.b.xfersize = ep->maxpacket;
-+ } else {
-+ deptsiz.b.xfersize = ep->xfer_len;
-+ }
-+ deptsiz.b.pktcnt = 1;
-+
-+ }
-+ DWC_DEBUGPL(DBG_PCDV,
-+ "IN len=%d xfersize=%d pktcnt=%d [%08x]\n",
-+ ep->xfer_len, deptsiz.b.xfersize, deptsiz.b.pktcnt,
-+ deptsiz.d32);
-+
-+ /* Write the DMA register */
-+ if (core_if->dma_enable) {
-+ if (core_if->dma_desc_enable == 0) {
-+ DWC_WRITE_REG32(&in_regs->dieptsiz,
-+ deptsiz.d32);
-+
-+ DWC_WRITE_REG32(&(in_regs->diepdma),
-+ (uint32_t) ep->dma_addr);
-+ } else {
-+ dma_desc = core_if->dev_if->in_desc_addr;
-+
-+ /** DMA Descriptor Setup */
-+ dma_desc->status.b.bs = BS_HOST_BUSY;
-+ dma_desc->status.b.l = 1;
-+ dma_desc->status.b.ioc = 1;
-+ dma_desc->status.b.sp =
-+ (ep->xfer_len == ep->maxpacket) ? 0 : 1;
-+ dma_desc->status.b.bytes = ep->xfer_len;
-+ dma_desc->buf = ep->dma_addr;
-+ dma_desc->status.b.sts = 0;
-+ dma_desc->status.b.bs = BS_HOST_READY;
-+
-+ /** DIEPDMA0 Register write */
-+ DWC_WRITE_REG32(&in_regs->diepdma,
-+ core_if->
-+ dev_if->dma_in_desc_addr);
-+ }
-+ } else {
-+ DWC_WRITE_REG32(&in_regs->dieptsiz, deptsiz.d32);
-+ }
-+
-+ if (!core_if->core_params->en_multiple_tx_fifo && core_if->dma_enable)
-+ depctl.b.nextep = core_if->nextep_seq[ep->num];
-+ /* EP enable, IN data in FIFO */
-+ depctl.b.cnak = 1;
-+ depctl.b.epena = 1;
-+ DWC_WRITE_REG32(&in_regs->diepctl, depctl.d32);
-+
-+ /**
-+ * Enable the Non-Periodic Tx FIFO empty interrupt, the
-+ * data will be written into the fifo by the ISR.
-+ */
-+ if (!core_if->dma_enable) {
-+ if (core_if->en_multiple_tx_fifo == 0) {
-+ intr_mask.b.nptxfempty = 1;
-+ DWC_MODIFY_REG32(&core_if->
-+ core_global_regs->gintmsk,
-+ intr_mask.d32, intr_mask.d32);
-+ } else {
-+ /* Enable the Tx FIFO Empty Interrupt for this EP */
-+ if (ep->xfer_len > 0) {
-+ uint32_t fifoemptymsk = 0;
-+ fifoemptymsk |= 1 << ep->num;
-+ DWC_MODIFY_REG32(&core_if->
-+ dev_if->dev_global_regs->dtknqr4_fifoemptymsk,
-+ 0, fifoemptymsk);
-+ }
-+ }
-+ }
-+ } else {
-+ /* OUT endpoint */
-+ dwc_otg_dev_out_ep_regs_t *out_regs =
-+ core_if->dev_if->out_ep_regs[0];
-+
-+ depctl.d32 = DWC_READ_REG32(&out_regs->doepctl);
-+ deptsiz.d32 = DWC_READ_REG32(&out_regs->doeptsiz);
-+
-+ /* Program the transfer size and packet count as follows:
-+ * xfersize = N * (maxpacket + 4 - (maxpacket % 4))
-+ * pktcnt = N */
-+ /* Zero Length Packet */
-+ deptsiz.b.xfersize = ep->maxpacket;
-+ deptsiz.b.pktcnt = 1;
-+ if (core_if->snpsid >= OTG_CORE_REV_3_00a)
-+ deptsiz.b.supcnt = 3;
-+
-+ DWC_DEBUGPL(DBG_PCDV, "len=%d xfersize=%d pktcnt=%d\n",
-+ ep->xfer_len, deptsiz.b.xfersize, deptsiz.b.pktcnt);
-+
-+ if (core_if->dma_enable) {
-+ if (!core_if->dma_desc_enable) {
-+ DWC_WRITE_REG32(&out_regs->doeptsiz,
-+ deptsiz.d32);
-+
-+ DWC_WRITE_REG32(&(out_regs->doepdma),
-+ (uint32_t) ep->dma_addr);
-+ } else {
-+ dma_desc = core_if->dev_if->out_desc_addr;
-+
-+ /** DMA Descriptor Setup */
-+ dma_desc->status.b.bs = BS_HOST_BUSY;
-+ if (core_if->snpsid >= OTG_CORE_REV_3_00a) {
-+ dma_desc->status.b.mtrf = 0;
-+ dma_desc->status.b.sr = 0;
-+ }
-+ dma_desc->status.b.l = 1;
-+ dma_desc->status.b.ioc = 1;
-+ dma_desc->status.b.bytes = ep->maxpacket;
-+ dma_desc->buf = ep->dma_addr;
-+ dma_desc->status.b.sts = 0;
-+ dma_desc->status.b.bs = BS_HOST_READY;
-+
-+ /** DOEPDMA0 Register write */
-+ DWC_WRITE_REG32(&out_regs->doepdma,
-+ core_if->dev_if->
-+ dma_out_desc_addr);
-+ }
-+ } else {
-+ DWC_WRITE_REG32(&out_regs->doeptsiz, deptsiz.d32);
-+ }
-+
-+ /* EP enable */
-+ depctl.b.cnak = 1;
-+ depctl.b.epena = 1;
-+ DWC_WRITE_REG32(&(out_regs->doepctl), depctl.d32);
-+ }
-+}
-+
-+/**
-+ * This function continues control IN transfers started by
-+ * dwc_otg_ep0_start_transfer, when the transfer does not fit in a
-+ * single packet. NOTE: The DIEPCTL0/DOEPCTL0 registers only have one
-+ * bit for the packet count.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param ep The EP0 data.
-+ */
-+void dwc_otg_ep0_continue_transfer(dwc_otg_core_if_t * core_if, dwc_ep_t * ep)
-+{
-+ depctl_data_t depctl;
-+ deptsiz0_data_t deptsiz;
-+ gintmsk_data_t intr_mask = {.d32 = 0 };
-+ dwc_otg_dev_dma_desc_t *dma_desc;
-+
-+ if (ep->is_in == 1) {
-+ dwc_otg_dev_in_ep_regs_t *in_regs =
-+ core_if->dev_if->in_ep_regs[0];
-+ gnptxsts_data_t tx_status = {.d32 = 0 };
-+
-+ tx_status.d32 =
-+ DWC_READ_REG32(&core_if->core_global_regs->gnptxsts);
-+ /** @todo Should there be check for room in the Tx
-+ * Status Queue. If not remove the code above this comment. */
-+
-+ depctl.d32 = DWC_READ_REG32(&in_regs->diepctl);
-+ deptsiz.d32 = DWC_READ_REG32(&in_regs->dieptsiz);
-+
-+ /* Program the transfer size and packet count
-+ * as follows: xfersize = N * maxpacket +
-+ * short_packet pktcnt = N + (short_packet
-+ * exist ? 1 : 0)
-+ */
-+
-+ if (core_if->dma_desc_enable == 0) {
-+ deptsiz.b.xfersize =
-+ (ep->total_len - ep->xfer_count) >
-+ ep->maxpacket ? ep->maxpacket : (ep->total_len -
-+ ep->xfer_count);
-+ deptsiz.b.pktcnt = 1;
-+ if (core_if->dma_enable == 0) {
-+ ep->xfer_len += deptsiz.b.xfersize;
-+ } else {
-+ ep->xfer_len = deptsiz.b.xfersize;
-+ }
-+ DWC_WRITE_REG32(&in_regs->dieptsiz, deptsiz.d32);
-+ } else {
-+ ep->xfer_len =
-+ (ep->total_len - ep->xfer_count) >
-+ ep->maxpacket ? ep->maxpacket : (ep->total_len -
-+ ep->xfer_count);
-+
-+ dma_desc = core_if->dev_if->in_desc_addr;
-+
-+ /** DMA Descriptor Setup */
-+ dma_desc->status.b.bs = BS_HOST_BUSY;
-+ dma_desc->status.b.l = 1;
-+ dma_desc->status.b.ioc = 1;
-+ dma_desc->status.b.sp =
-+ (ep->xfer_len == ep->maxpacket) ? 0 : 1;
-+ dma_desc->status.b.bytes = ep->xfer_len;
-+ dma_desc->buf = ep->dma_addr;
-+ dma_desc->status.b.sts = 0;
-+ dma_desc->status.b.bs = BS_HOST_READY;
-+
-+ /** DIEPDMA0 Register write */
-+ DWC_WRITE_REG32(&in_regs->diepdma,
-+ core_if->dev_if->dma_in_desc_addr);
-+ }
-+
-+ DWC_DEBUGPL(DBG_PCDV,
-+ "IN len=%d xfersize=%d pktcnt=%d [%08x]\n",
-+ ep->xfer_len, deptsiz.b.xfersize, deptsiz.b.pktcnt,
-+ deptsiz.d32);
-+
-+ /* Write the DMA register */
-+ if (core_if->hwcfg2.b.architecture == DWC_INT_DMA_ARCH) {
-+ if (core_if->dma_desc_enable == 0)
-+ DWC_WRITE_REG32(&(in_regs->diepdma),
-+ (uint32_t) ep->dma_addr);
-+ }
-+ if (!core_if->core_params->en_multiple_tx_fifo && core_if->dma_enable)
-+ depctl.b.nextep = core_if->nextep_seq[ep->num];
-+ /* EP enable, IN data in FIFO */
-+ depctl.b.cnak = 1;
-+ depctl.b.epena = 1;
-+ DWC_WRITE_REG32(&in_regs->diepctl, depctl.d32);
-+
-+ /**
-+ * Enable the Non-Periodic Tx FIFO empty interrupt, the
-+ * data will be written into the fifo by the ISR.
-+ */
-+ if (!core_if->dma_enable) {
-+ if (core_if->en_multiple_tx_fifo == 0) {
-+ /* First clear it from GINTSTS */
-+ intr_mask.b.nptxfempty = 1;
-+ DWC_MODIFY_REG32(&core_if->
-+ core_global_regs->gintmsk,
-+ intr_mask.d32, intr_mask.d32);
-+
-+ } else {
-+ /* Enable the Tx FIFO Empty Interrupt for this EP */
-+ if (ep->xfer_len > 0) {
-+ uint32_t fifoemptymsk = 0;
-+ fifoemptymsk |= 1 << ep->num;
-+ DWC_MODIFY_REG32(&core_if->
-+ dev_if->dev_global_regs->dtknqr4_fifoemptymsk,
-+ 0, fifoemptymsk);
-+ }
-+ }
-+ }
-+ } else {
-+ dwc_otg_dev_out_ep_regs_t *out_regs =
-+ core_if->dev_if->out_ep_regs[0];
-+
-+ depctl.d32 = DWC_READ_REG32(&out_regs->doepctl);
-+ deptsiz.d32 = DWC_READ_REG32(&out_regs->doeptsiz);
-+
-+ /* Program the transfer size and packet count
-+ * as follows: xfersize = N * maxpacket +
-+ * short_packet pktcnt = N + (short_packet
-+ * exist ? 1 : 0)
-+ */
-+ deptsiz.b.xfersize = ep->maxpacket;
-+ deptsiz.b.pktcnt = 1;
-+
-+ if (core_if->dma_desc_enable == 0) {
-+ DWC_WRITE_REG32(&out_regs->doeptsiz, deptsiz.d32);
-+ } else {
-+ dma_desc = core_if->dev_if->out_desc_addr;
-+
-+ /** DMA Descriptor Setup */
-+ dma_desc->status.b.bs = BS_HOST_BUSY;
-+ dma_desc->status.b.l = 1;
-+ dma_desc->status.b.ioc = 1;
-+ dma_desc->status.b.bytes = ep->maxpacket;
-+ dma_desc->buf = ep->dma_addr;
-+ dma_desc->status.b.sts = 0;
-+ dma_desc->status.b.bs = BS_HOST_READY;
-+
-+ /** DOEPDMA0 Register write */
-+ DWC_WRITE_REG32(&out_regs->doepdma,
-+ core_if->dev_if->dma_out_desc_addr);
-+ }
-+
-+ DWC_DEBUGPL(DBG_PCDV,
-+ "IN len=%d xfersize=%d pktcnt=%d [%08x]\n",
-+ ep->xfer_len, deptsiz.b.xfersize, deptsiz.b.pktcnt,
-+ deptsiz.d32);
-+
-+ /* Write the DMA register */
-+ if (core_if->hwcfg2.b.architecture == DWC_INT_DMA_ARCH) {
-+ if (core_if->dma_desc_enable == 0)
-+ DWC_WRITE_REG32(&(out_regs->doepdma),
-+ (uint32_t) ep->dma_addr);
-+
-+ }
-+
-+ /* EP enable, IN data in FIFO */
-+ depctl.b.cnak = 1;
-+ depctl.b.epena = 1;
-+ DWC_WRITE_REG32(&out_regs->doepctl, depctl.d32);
-+
-+ }
-+}
-+
-+#ifdef DEBUG
-+void dump_msg(const u8 * buf, unsigned int length)
-+{
-+ unsigned int start, num, i;
-+ char line[52], *p;
-+
-+ if (length >= 512)
-+ return;
-+ start = 0;
-+ while (length > 0) {
-+ num = length < 16u ? length : 16u;
-+ p = line;
-+ for (i = 0; i < num; ++i) {
-+ if (i == 8)
-+ *p++ = ' ';
-+ DWC_SPRINTF(p, " %02x", buf[i]);
-+ p += 3;
-+ }
-+ *p = 0;
-+ DWC_PRINTF("%6x: %s\n", start, line);
-+ buf += num;
-+ start += num;
-+ length -= num;
-+ }
-+}
-+#else
-+static inline void dump_msg(const u8 * buf, unsigned int length)
-+{
-+}
-+#endif
-+
-+/**
-+ * This function writes a packet into the Tx FIFO associated with the
-+ * EP. For non-periodic EPs the non-periodic Tx FIFO is written. For
-+ * periodic EPs the periodic Tx FIFO associated with the EP is written
-+ * with all packets for the next micro-frame.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param ep The EP to write packet for.
-+ * @param dma Indicates if DMA is being used.
-+ */
-+void dwc_otg_ep_write_packet(dwc_otg_core_if_t * core_if, dwc_ep_t * ep,
-+ int dma)
-+{
-+ /**
-+ * The buffer is padded to DWORD on a per packet basis in
-+ * slave/dma mode if the MPS is not DWORD aligned. The last
-+ * packet, if short, is also padded to a multiple of DWORD.
-+ *
-+ * ep->xfer_buff always starts DWORD aligned in memory and is a
-+ * multiple of DWORD in length
-+ *
-+ * ep->xfer_len can be any number of bytes
-+ *
-+ * ep->xfer_count is a multiple of ep->maxpacket until the last
-+ * packet
-+ *
-+ * FIFO access is DWORD */
-+
-+ uint32_t i;
-+ uint32_t byte_count;
-+ uint32_t dword_count;
-+ uint32_t *fifo;
-+ uint32_t *data_buff = (uint32_t *) ep->xfer_buff;
-+
-+ DWC_DEBUGPL((DBG_PCDV | DBG_CILV), "%s(%p,%p)\n", __func__, core_if,
-+ ep);
-+ if (ep->xfer_count >= ep->xfer_len) {
-+ DWC_WARN("%s() No data for EP%d!!!\n", __func__, ep->num);
-+ return;
-+ }
-+
-+ /* Find the byte length of the packet either short packet or MPS */
-+ if ((ep->xfer_len - ep->xfer_count) < ep->maxpacket) {
-+ byte_count = ep->xfer_len - ep->xfer_count;
-+ } else {
-+ byte_count = ep->maxpacket;
-+ }
-+
-+ /* Find the DWORD length, padded by extra bytes as neccessary if MPS
-+ * is not a multiple of DWORD */
-+ dword_count = (byte_count + 3) / 4;
-+
-+#ifdef VERBOSE
-+ dump_msg(ep->xfer_buff, byte_count);
-+#endif
-+
-+ /**@todo NGS Where are the Periodic Tx FIFO addresses
-+ * intialized? What should this be? */
-+
-+ fifo = core_if->data_fifo[ep->num];
-+
-+ DWC_DEBUGPL((DBG_PCDV | DBG_CILV), "fifo=%p buff=%p *p=%08x bc=%d\n",
-+ fifo, data_buff, *data_buff, byte_count);
-+
-+ if (!dma) {
-+ for (i = 0; i < dword_count; i++, data_buff++) {
-+ DWC_WRITE_REG32(fifo, *data_buff);
-+ }
-+ }
-+
-+ ep->xfer_count += byte_count;
-+ ep->xfer_buff += byte_count;
-+ ep->dma_addr += byte_count;
-+}
-+
-+/**
-+ * Set the EP STALL.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param ep The EP to set the stall on.
-+ */
-+void dwc_otg_ep_set_stall(dwc_otg_core_if_t * core_if, dwc_ep_t * ep)
-+{
-+ depctl_data_t depctl;
-+ volatile uint32_t *depctl_addr;
-+
-+ DWC_DEBUGPL(DBG_PCD, "%s ep%d-%s\n", __func__, ep->num,
-+ (ep->is_in ? "IN" : "OUT"));
-+
-+ if (ep->is_in == 1) {
-+ depctl_addr = &(core_if->dev_if->in_ep_regs[ep->num]->diepctl);
-+ depctl.d32 = DWC_READ_REG32(depctl_addr);
-+
-+ /* set the disable and stall bits */
-+ if (depctl.b.epena) {
-+ depctl.b.epdis = 1;
-+ }
-+ depctl.b.stall = 1;
-+ DWC_WRITE_REG32(depctl_addr, depctl.d32);
-+ } else {
-+ depctl_addr = &(core_if->dev_if->out_ep_regs[ep->num]->doepctl);
-+ depctl.d32 = DWC_READ_REG32(depctl_addr);
-+
-+ /* set the stall bit */
-+ depctl.b.stall = 1;
-+ DWC_WRITE_REG32(depctl_addr, depctl.d32);
-+ }
-+
-+ DWC_DEBUGPL(DBG_PCD, "DEPCTL=%0x\n", DWC_READ_REG32(depctl_addr));
-+
-+ return;
-+}
-+
-+/**
-+ * Clear the EP STALL.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param ep The EP to clear stall from.
-+ */
-+void dwc_otg_ep_clear_stall(dwc_otg_core_if_t * core_if, dwc_ep_t * ep)
-+{
-+ depctl_data_t depctl;
-+ volatile uint32_t *depctl_addr;
-+
-+ DWC_DEBUGPL(DBG_PCD, "%s ep%d-%s\n", __func__, ep->num,
-+ (ep->is_in ? "IN" : "OUT"));
-+
-+ if (ep->is_in == 1) {
-+ depctl_addr = &(core_if->dev_if->in_ep_regs[ep->num]->diepctl);
-+ } else {
-+ depctl_addr = &(core_if->dev_if->out_ep_regs[ep->num]->doepctl);
-+ }
-+
-+ depctl.d32 = DWC_READ_REG32(depctl_addr);
-+
-+ /* clear the stall bits */
-+ depctl.b.stall = 0;
-+
-+ /*
-+ * USB Spec 9.4.5: For endpoints using data toggle, regardless
-+ * of whether an endpoint has the Halt feature set, a
-+ * ClearFeature(ENDPOINT_HALT) request always results in the
-+ * data toggle being reinitialized to DATA0.
-+ */
-+ if (ep->type == DWC_OTG_EP_TYPE_INTR ||
-+ ep->type == DWC_OTG_EP_TYPE_BULK) {
-+ depctl.b.setd0pid = 1; /* DATA0 */
-+ }
-+
-+ DWC_WRITE_REG32(depctl_addr, depctl.d32);
-+ DWC_DEBUGPL(DBG_PCD, "DEPCTL=%0x\n", DWC_READ_REG32(depctl_addr));
-+ return;
-+}
-+
-+/**
-+ * This function reads a packet from the Rx FIFO into the destination
-+ * buffer. To read SETUP data use dwc_otg_read_setup_packet.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param dest Destination buffer for the packet.
-+ * @param bytes Number of bytes to copy to the destination.
-+ */
-+void dwc_otg_read_packet(dwc_otg_core_if_t * core_if,
-+ uint8_t * dest, uint16_t bytes)
-+{
-+ int i;
-+ int word_count = (bytes + 3) / 4;
-+
-+ volatile uint32_t *fifo = core_if->data_fifo[0];
-+ uint32_t *data_buff = (uint32_t *) dest;
-+
-+ /**
-+ * @todo Account for the case where _dest is not dword aligned. This
-+ * requires reading data from the FIFO into a uint32_t temp buffer,
-+ * then moving it into the data buffer.
-+ */
-+
-+ DWC_DEBUGPL((DBG_PCDV | DBG_CILV), "%s(%p,%p,%d)\n", __func__,
-+ core_if, dest, bytes);
-+
-+ for (i = 0; i < word_count; i++, data_buff++) {
-+ *data_buff = DWC_READ_REG32(fifo);
-+ }
-+
-+ return;
-+}
-+
-+/**
-+ * This functions reads the device registers and prints them
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ */
-+void dwc_otg_dump_dev_registers(dwc_otg_core_if_t * core_if)
-+{
-+ int i;
-+ volatile uint32_t *addr;
-+
-+ DWC_PRINTF("Device Global Registers\n");
-+ addr = &core_if->dev_if->dev_global_regs->dcfg;
-+ DWC_PRINTF("DCFG @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ addr = &core_if->dev_if->dev_global_regs->dctl;
-+ DWC_PRINTF("DCTL @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ addr = &core_if->dev_if->dev_global_regs->dsts;
-+ DWC_PRINTF("DSTS @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ addr = &core_if->dev_if->dev_global_regs->diepmsk;
-+ DWC_PRINTF("DIEPMSK @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->dev_if->dev_global_regs->doepmsk;
-+ DWC_PRINTF("DOEPMSK @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->dev_if->dev_global_regs->daint;
-+ DWC_PRINTF("DAINT @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->dev_if->dev_global_regs->daintmsk;
-+ DWC_PRINTF("DAINTMSK @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->dev_if->dev_global_regs->dtknqr1;
-+ DWC_PRINTF("DTKNQR1 @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ if (core_if->hwcfg2.b.dev_token_q_depth > 6) {
-+ addr = &core_if->dev_if->dev_global_regs->dtknqr2;
-+ DWC_PRINTF("DTKNQR2 @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ }
-+
-+ addr = &core_if->dev_if->dev_global_regs->dvbusdis;
-+ DWC_PRINTF("DVBUSID @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+
-+ addr = &core_if->dev_if->dev_global_regs->dvbuspulse;
-+ DWC_PRINTF("DVBUSPULSE @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+
-+ addr = &core_if->dev_if->dev_global_regs->dtknqr3_dthrctl;
-+ DWC_PRINTF("DTKNQR3_DTHRCTL @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+
-+ if (core_if->hwcfg2.b.dev_token_q_depth > 22) {
-+ addr = &core_if->dev_if->dev_global_regs->dtknqr4_fifoemptymsk;
-+ DWC_PRINTF("DTKNQR4 @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ }
-+
-+ addr = &core_if->dev_if->dev_global_regs->dtknqr4_fifoemptymsk;
-+ DWC_PRINTF("FIFOEMPMSK @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+
-+ if (core_if->hwcfg2.b.multi_proc_int) {
-+
-+ addr = &core_if->dev_if->dev_global_regs->deachint;
-+ DWC_PRINTF("DEACHINT @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ addr = &core_if->dev_if->dev_global_regs->deachintmsk;
-+ DWC_PRINTF("DEACHINTMSK @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+
-+ for (i = 0; i <= core_if->dev_if->num_in_eps; i++) {
-+ addr =
-+ &core_if->dev_if->
-+ dev_global_regs->diepeachintmsk[i];
-+ DWC_PRINTF("DIEPEACHINTMSK[%d] @0x%08lX : 0x%08X\n",
-+ i, (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ }
-+
-+ for (i = 0; i <= core_if->dev_if->num_out_eps; i++) {
-+ addr =
-+ &core_if->dev_if->
-+ dev_global_regs->doepeachintmsk[i];
-+ DWC_PRINTF("DOEPEACHINTMSK[%d] @0x%08lX : 0x%08X\n",
-+ i, (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ }
-+ }
-+
-+ for (i = 0; i <= core_if->dev_if->num_in_eps; i++) {
-+ DWC_PRINTF("Device IN EP %d Registers\n", i);
-+ addr = &core_if->dev_if->in_ep_regs[i]->diepctl;
-+ DWC_PRINTF("DIEPCTL @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ addr = &core_if->dev_if->in_ep_regs[i]->diepint;
-+ DWC_PRINTF("DIEPINT @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ addr = &core_if->dev_if->in_ep_regs[i]->dieptsiz;
-+ DWC_PRINTF("DIETSIZ @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ addr = &core_if->dev_if->in_ep_regs[i]->diepdma;
-+ DWC_PRINTF("DIEPDMA @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ addr = &core_if->dev_if->in_ep_regs[i]->dtxfsts;
-+ DWC_PRINTF("DTXFSTS @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ addr = &core_if->dev_if->in_ep_regs[i]->diepdmab;
-+ DWC_PRINTF("DIEPDMAB @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, 0 /*DWC_READ_REG32(addr) */ );
-+ }
-+
-+ for (i = 0; i <= core_if->dev_if->num_out_eps; i++) {
-+ DWC_PRINTF("Device OUT EP %d Registers\n", i);
-+ addr = &core_if->dev_if->out_ep_regs[i]->doepctl;
-+ DWC_PRINTF("DOEPCTL @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ addr = &core_if->dev_if->out_ep_regs[i]->doepint;
-+ DWC_PRINTF("DOEPINT @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ addr = &core_if->dev_if->out_ep_regs[i]->doeptsiz;
-+ DWC_PRINTF("DOETSIZ @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ addr = &core_if->dev_if->out_ep_regs[i]->doepdma;
-+ DWC_PRINTF("DOEPDMA @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ if (core_if->dma_enable) { /* Don't access this register in SLAVE mode */
-+ addr = &core_if->dev_if->out_ep_regs[i]->doepdmab;
-+ DWC_PRINTF("DOEPDMAB @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ }
-+
-+ }
-+}
-+
-+/**
-+ * This functions reads the SPRAM and prints its content
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ */
-+void dwc_otg_dump_spram(dwc_otg_core_if_t * core_if)
-+{
-+ volatile uint8_t *addr, *start_addr, *end_addr;
-+
-+ DWC_PRINTF("SPRAM Data:\n");
-+ start_addr = (void *)core_if->core_global_regs;
-+ DWC_PRINTF("Base Address: 0x%8lX\n", (unsigned long)start_addr);
-+ start_addr += 0x00028000;
-+ end_addr = (void *)core_if->core_global_regs;
-+ end_addr += 0x000280e0;
-+
-+ for (addr = start_addr; addr < end_addr; addr += 16) {
-+ DWC_PRINTF
-+ ("0x%8lX:\t%2X %2X %2X %2X %2X %2X %2X %2X %2X %2X %2X %2X %2X %2X %2X %2X\n",
-+ (unsigned long)addr, addr[0], addr[1], addr[2], addr[3],
-+ addr[4], addr[5], addr[6], addr[7], addr[8], addr[9],
-+ addr[10], addr[11], addr[12], addr[13], addr[14], addr[15]
-+ );
-+ }
-+
-+ return;
-+}
-+
-+/**
-+ * This function reads the host registers and prints them
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ */
-+void dwc_otg_dump_host_registers(dwc_otg_core_if_t * core_if)
-+{
-+ int i;
-+ volatile uint32_t *addr;
-+
-+ DWC_PRINTF("Host Global Registers\n");
-+ addr = &core_if->host_if->host_global_regs->hcfg;
-+ DWC_PRINTF("HCFG @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ addr = &core_if->host_if->host_global_regs->hfir;
-+ DWC_PRINTF("HFIR @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ addr = &core_if->host_if->host_global_regs->hfnum;
-+ DWC_PRINTF("HFNUM @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->host_if->host_global_regs->hptxsts;
-+ DWC_PRINTF("HPTXSTS @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->host_if->host_global_regs->haint;
-+ DWC_PRINTF("HAINT @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->host_if->host_global_regs->haintmsk;
-+ DWC_PRINTF("HAINTMSK @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ if (core_if->dma_desc_enable) {
-+ addr = &core_if->host_if->host_global_regs->hflbaddr;
-+ DWC_PRINTF("HFLBADDR @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ }
-+
-+ addr = core_if->host_if->hprt0;
-+ DWC_PRINTF("HPRT0 @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+
-+ for (i = 0; i < core_if->core_params->host_channels; i++) {
-+ DWC_PRINTF("Host Channel %d Specific Registers\n", i);
-+ addr = &core_if->host_if->hc_regs[i]->hcchar;
-+ DWC_PRINTF("HCCHAR @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ addr = &core_if->host_if->hc_regs[i]->hcsplt;
-+ DWC_PRINTF("HCSPLT @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ addr = &core_if->host_if->hc_regs[i]->hcint;
-+ DWC_PRINTF("HCINT @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ addr = &core_if->host_if->hc_regs[i]->hcintmsk;
-+ DWC_PRINTF("HCINTMSK @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ addr = &core_if->host_if->hc_regs[i]->hctsiz;
-+ DWC_PRINTF("HCTSIZ @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ addr = &core_if->host_if->hc_regs[i]->hcdma;
-+ DWC_PRINTF("HCDMA @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ if (core_if->dma_desc_enable) {
-+ addr = &core_if->host_if->hc_regs[i]->hcdmab;
-+ DWC_PRINTF("HCDMAB @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ }
-+
-+ }
-+ return;
-+}
-+
-+/**
-+ * This function reads the core global registers and prints them
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ */
-+void dwc_otg_dump_global_registers(dwc_otg_core_if_t * core_if)
-+{
-+ int i, ep_num;
-+ volatile uint32_t *addr;
-+ char *txfsiz;
-+
-+ DWC_PRINTF("Core Global Registers\n");
-+ addr = &core_if->core_global_regs->gotgctl;
-+ DWC_PRINTF("GOTGCTL @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->core_global_regs->gotgint;
-+ DWC_PRINTF("GOTGINT @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->core_global_regs->gahbcfg;
-+ DWC_PRINTF("GAHBCFG @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->core_global_regs->gusbcfg;
-+ DWC_PRINTF("GUSBCFG @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->core_global_regs->grstctl;
-+ DWC_PRINTF("GRSTCTL @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->core_global_regs->gintsts;
-+ DWC_PRINTF("GINTSTS @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->core_global_regs->gintmsk;
-+ DWC_PRINTF("GINTMSK @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->core_global_regs->grxstsr;
-+ DWC_PRINTF("GRXSTSR @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->core_global_regs->grxfsiz;
-+ DWC_PRINTF("GRXFSIZ @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->core_global_regs->gnptxfsiz;
-+ DWC_PRINTF("GNPTXFSIZ @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->core_global_regs->gnptxsts;
-+ DWC_PRINTF("GNPTXSTS @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->core_global_regs->gi2cctl;
-+ DWC_PRINTF("GI2CCTL @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->core_global_regs->gpvndctl;
-+ DWC_PRINTF("GPVNDCTL @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->core_global_regs->ggpio;
-+ DWC_PRINTF("GGPIO @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->core_global_regs->guid;
-+ DWC_PRINTF("GUID @0x%08lX : 0x%08X\n",
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ addr = &core_if->core_global_regs->gsnpsid;
-+ DWC_PRINTF("GSNPSID @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->core_global_regs->ghwcfg1;
-+ DWC_PRINTF("GHWCFG1 @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->core_global_regs->ghwcfg2;
-+ DWC_PRINTF("GHWCFG2 @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->core_global_regs->ghwcfg3;
-+ DWC_PRINTF("GHWCFG3 @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->core_global_regs->ghwcfg4;
-+ DWC_PRINTF("GHWCFG4 @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->core_global_regs->glpmcfg;
-+ DWC_PRINTF("GLPMCFG @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->core_global_regs->gpwrdn;
-+ DWC_PRINTF("GPWRDN @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->core_global_regs->gdfifocfg;
-+ DWC_PRINTF("GDFIFOCFG @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+ addr = &core_if->core_global_regs->adpctl;
-+ DWC_PRINTF("ADPCTL @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ dwc_otg_adp_read_reg(core_if));
-+ addr = &core_if->core_global_regs->hptxfsiz;
-+ DWC_PRINTF("HPTXFSIZ @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+
-+ if (core_if->en_multiple_tx_fifo == 0) {
-+ ep_num = core_if->hwcfg4.b.num_dev_perio_in_ep;
-+ txfsiz = "DPTXFSIZ";
-+ } else {
-+ ep_num = core_if->hwcfg4.b.num_in_eps;
-+ txfsiz = "DIENPTXF";
-+ }
-+ for (i = 0; i < ep_num; i++) {
-+ addr = &core_if->core_global_regs->dtxfsiz[i];
-+ DWC_PRINTF("%s[%d] @0x%08lX : 0x%08X\n", txfsiz, i + 1,
-+ (unsigned long)addr, DWC_READ_REG32(addr));
-+ }
-+ addr = core_if->pcgcctl;
-+ DWC_PRINTF("PCGCCTL @0x%08lX : 0x%08X\n", (unsigned long)addr,
-+ DWC_READ_REG32(addr));
-+}
-+
-+/**
-+ * Flush a Tx FIFO.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param num Tx FIFO to flush.
-+ */
-+void dwc_otg_flush_tx_fifo(dwc_otg_core_if_t * core_if, const int num)
-+{
-+ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs;
-+ volatile grstctl_t greset = {.d32 = 0 };
-+ int count = 0;
-+
-+ DWC_DEBUGPL((DBG_CIL | DBG_PCDV), "Flush Tx FIFO %d\n", num);
-+
-+ greset.b.txfflsh = 1;
-+ greset.b.txfnum = num;
-+ DWC_WRITE_REG32(&global_regs->grstctl, greset.d32);
-+
-+ do {
-+ greset.d32 = DWC_READ_REG32(&global_regs->grstctl);
-+ if (++count > 10000) {
-+ DWC_WARN("%s() HANG! GRSTCTL=%0x GNPTXSTS=0x%08x\n",
-+ __func__, greset.d32,
-+ DWC_READ_REG32(&global_regs->gnptxsts));
-+ break;
-+ }
-+ dwc_udelay(1);
-+ } while (greset.b.txfflsh == 1);
-+
-+ /* Wait for 3 PHY Clocks */
-+ dwc_udelay(1);
-+}
-+
-+/**
-+ * Flush Rx FIFO.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ */
-+void dwc_otg_flush_rx_fifo(dwc_otg_core_if_t * core_if)
-+{
-+ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs;
-+ volatile grstctl_t greset = {.d32 = 0 };
-+ int count = 0;
-+
-+ DWC_DEBUGPL((DBG_CIL | DBG_PCDV), "%s\n", __func__);
-+ /*
-+ *
-+ */
-+ greset.b.rxfflsh = 1;
-+ DWC_WRITE_REG32(&global_regs->grstctl, greset.d32);
-+
-+ do {
-+ greset.d32 = DWC_READ_REG32(&global_regs->grstctl);
-+ if (++count > 10000) {
-+ DWC_WARN("%s() HANG! GRSTCTL=%0x\n", __func__,
-+ greset.d32);
-+ break;
-+ }
-+ dwc_udelay(1);
-+ } while (greset.b.rxfflsh == 1);
-+
-+ /* Wait for 3 PHY Clocks */
-+ dwc_udelay(1);
-+}
-+
-+/**
-+ * Do core a soft reset of the core. Be careful with this because it
-+ * resets all the internal state machines of the core.
-+ */
-+void dwc_otg_core_reset(dwc_otg_core_if_t * core_if)
-+{
-+ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs;
-+ volatile grstctl_t greset = {.d32 = 0 };
-+ int count = 0;
-+
-+ DWC_DEBUGPL(DBG_CILV, "%s\n", __func__);
-+ /* Wait for AHB master IDLE state. */
-+ do {
-+ dwc_udelay(10);
-+ greset.d32 = DWC_READ_REG32(&global_regs->grstctl);
-+ if (++count > 100000) {
-+ DWC_WARN("%s() HANG! AHB Idle GRSTCTL=%0x\n", __func__,
-+ greset.d32);
-+ return;
-+ }
-+ }
-+ while (greset.b.ahbidle == 0);
-+
-+ /* Core Soft Reset */
-+ count = 0;
-+ greset.b.csftrst = 1;
-+ DWC_WRITE_REG32(&global_regs->grstctl, greset.d32);
-+ do {
-+ greset.d32 = DWC_READ_REG32(&global_regs->grstctl);
-+ if (++count > 10000) {
-+ DWC_WARN("%s() HANG! Soft Reset GRSTCTL=%0x\n",
-+ __func__, greset.d32);
-+ break;
-+ }
-+ dwc_udelay(1);
-+ }
-+ while (greset.b.csftrst == 1);
-+
-+ /* Wait for 3 PHY Clocks */
-+ dwc_mdelay(100);
-+}
-+
-+uint8_t dwc_otg_is_device_mode(dwc_otg_core_if_t * _core_if)
-+{
-+ return (dwc_otg_mode(_core_if) != DWC_HOST_MODE);
-+}
-+
-+uint8_t dwc_otg_is_host_mode(dwc_otg_core_if_t * _core_if)
-+{
-+ return (dwc_otg_mode(_core_if) == DWC_HOST_MODE);
-+}
-+
-+/**
-+ * Register HCD callbacks. The callbacks are used to start and stop
-+ * the HCD for interrupt processing.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param cb the HCD callback structure.
-+ * @param p pointer to be passed to callback function (usb_hcd*).
-+ */
-+void dwc_otg_cil_register_hcd_callbacks(dwc_otg_core_if_t * core_if,
-+ dwc_otg_cil_callbacks_t * cb, void *p)
-+{
-+ core_if->hcd_cb = cb;
-+ cb->p = p;
-+}
-+
-+/**
-+ * Register PCD callbacks. The callbacks are used to start and stop
-+ * the PCD for interrupt processing.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param cb the PCD callback structure.
-+ * @param p pointer to be passed to callback function (pcd*).
-+ */
-+void dwc_otg_cil_register_pcd_callbacks(dwc_otg_core_if_t * core_if,
-+ dwc_otg_cil_callbacks_t * cb, void *p)
-+{
-+ core_if->pcd_cb = cb;
-+ cb->p = p;
-+}
-+
-+#ifdef DWC_EN_ISOC
-+
-+/**
-+ * This function writes isoc data per 1 (micro)frame into tx fifo
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param ep The EP to start the transfer on.
-+ *
-+ */
-+void write_isoc_frame_data(dwc_otg_core_if_t * core_if, dwc_ep_t * ep)
-+{
-+ dwc_otg_dev_in_ep_regs_t *ep_regs;
-+ dtxfsts_data_t txstatus = {.d32 = 0 };
-+ uint32_t len = 0;
-+ uint32_t dwords;
-+
-+ ep->xfer_len = ep->data_per_frame;
-+ ep->xfer_count = 0;
-+
-+ ep_regs = core_if->dev_if->in_ep_regs[ep->num];
-+
-+ len = ep->xfer_len - ep->xfer_count;
-+
-+ if (len > ep->maxpacket) {
-+ len = ep->maxpacket;
-+ }
-+
-+ dwords = (len + 3) / 4;
-+
-+ /* While there is space in the queue and space in the FIFO and
-+ * More data to tranfer, Write packets to the Tx FIFO */
-+ txstatus.d32 =
-+ DWC_READ_REG32(&core_if->dev_if->in_ep_regs[ep->num]->dtxfsts);
-+ DWC_DEBUGPL(DBG_PCDV, "b4 dtxfsts[%d]=0x%08x\n", ep->num, txstatus.d32);
-+
-+ while (txstatus.b.txfspcavail > dwords &&
-+ ep->xfer_count < ep->xfer_len && ep->xfer_len != 0) {
-+ /* Write the FIFO */
-+ dwc_otg_ep_write_packet(core_if, ep, 0);
-+
-+ len = ep->xfer_len - ep->xfer_count;
-+ if (len > ep->maxpacket) {
-+ len = ep->maxpacket;
-+ }
-+
-+ dwords = (len + 3) / 4;
-+ txstatus.d32 =
-+ DWC_READ_REG32(&core_if->dev_if->in_ep_regs[ep->num]->
-+ dtxfsts);
-+ DWC_DEBUGPL(DBG_PCDV, "dtxfsts[%d]=0x%08x\n", ep->num,
-+ txstatus.d32);
-+ }
-+}
-+
-+/**
-+ * This function initializes a descriptor chain for Isochronous transfer
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param ep The EP to start the transfer on.
-+ *
-+ */
-+void dwc_otg_iso_ep_start_frm_transfer(dwc_otg_core_if_t * core_if,
-+ dwc_ep_t * ep)
-+{
-+ deptsiz_data_t deptsiz = {.d32 = 0 };
-+ depctl_data_t depctl = {.d32 = 0 };
-+ dsts_data_t dsts = {.d32 = 0 };
-+ volatile uint32_t *addr;
-+
-+ if (ep->is_in) {
-+ addr = &core_if->dev_if->in_ep_regs[ep->num]->diepctl;
-+ } else {
-+ addr = &core_if->dev_if->out_ep_regs[ep->num]->doepctl;
-+ }
-+
-+ ep->xfer_len = ep->data_per_frame;
-+ ep->xfer_count = 0;
-+ ep->xfer_buff = ep->cur_pkt_addr;
-+ ep->dma_addr = ep->cur_pkt_dma_addr;
-+
-+ if (ep->is_in) {
-+ /* Program the transfer size and packet count
-+ * as follows: xfersize = N * maxpacket +
-+ * short_packet pktcnt = N + (short_packet
-+ * exist ? 1 : 0)
-+ */
-+ deptsiz.b.xfersize = ep->xfer_len;
-+ deptsiz.b.pktcnt =
-+ (ep->xfer_len - 1 + ep->maxpacket) / ep->maxpacket;
-+ deptsiz.b.mc = deptsiz.b.pktcnt;
-+ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[ep->num]->dieptsiz,
-+ deptsiz.d32);
-+
-+ /* Write the DMA register */
-+ if (core_if->dma_enable) {
-+ DWC_WRITE_REG32(&
-+ (core_if->dev_if->in_ep_regs[ep->num]->
-+ diepdma), (uint32_t) ep->dma_addr);
-+ }
-+ } else {
-+ deptsiz.b.pktcnt =
-+ (ep->xfer_len + (ep->maxpacket - 1)) / ep->maxpacket;
-+ deptsiz.b.xfersize = deptsiz.b.pktcnt * ep->maxpacket;
-+
-+ DWC_WRITE_REG32(&core_if->dev_if->
-+ out_ep_regs[ep->num]->doeptsiz, deptsiz.d32);
-+
-+ if (core_if->dma_enable) {
-+ DWC_WRITE_REG32(&
-+ (core_if->dev_if->
-+ out_ep_regs[ep->num]->doepdma),
-+ (uint32_t) ep->dma_addr);
-+ }
-+ }
-+
-+ /** Enable endpoint, clear nak */
-+
-+ depctl.d32 = 0;
-+ if (ep->bInterval == 1) {
-+ dsts.d32 =
-+ DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dsts);
-+ ep->next_frame = dsts.b.soffn + ep->bInterval;
-+
-+ if (ep->next_frame & 0x1) {
-+ depctl.b.setd1pid = 1;
-+ } else {
-+ depctl.b.setd0pid = 1;
-+ }
-+ } else {
-+ ep->next_frame += ep->bInterval;
-+
-+ if (ep->next_frame & 0x1) {
-+ depctl.b.setd1pid = 1;
-+ } else {
-+ depctl.b.setd0pid = 1;
-+ }
-+ }
-+ depctl.b.epena = 1;
-+ depctl.b.cnak = 1;
-+
-+ DWC_MODIFY_REG32(addr, 0, depctl.d32);
-+ depctl.d32 = DWC_READ_REG32(addr);
-+
-+ if (ep->is_in && core_if->dma_enable == 0) {
-+ write_isoc_frame_data(core_if, ep);
-+ }
-+
-+}
-+#endif /* DWC_EN_ISOC */
-+
-+static void dwc_otg_set_uninitialized(int32_t * p, int size)
-+{
-+ int i;
-+ for (i = 0; i < size; i++) {
-+ p[i] = -1;
-+ }
-+}
-+
-+static int dwc_otg_param_initialized(int32_t val)
-+{
-+ return val != -1;
-+}
-+
-+static int dwc_otg_setup_params(dwc_otg_core_if_t * core_if)
-+{
-+ int i;
-+ core_if->core_params = DWC_ALLOC(sizeof(*core_if->core_params));
-+ if (!core_if->core_params) {
-+ return -DWC_E_NO_MEMORY;
-+ }
-+ dwc_otg_set_uninitialized((int32_t *) core_if->core_params,
-+ sizeof(*core_if->core_params) /
-+ sizeof(int32_t));
-+ DWC_PRINTF("Setting default values for core params\n");
-+ dwc_otg_set_param_otg_cap(core_if, dwc_param_otg_cap_default);
-+ dwc_otg_set_param_dma_enable(core_if, dwc_param_dma_enable_default);
-+ dwc_otg_set_param_dma_desc_enable(core_if,
-+ dwc_param_dma_desc_enable_default);
-+ dwc_otg_set_param_opt(core_if, dwc_param_opt_default);
-+ dwc_otg_set_param_dma_burst_size(core_if,
-+ dwc_param_dma_burst_size_default);
-+ dwc_otg_set_param_host_support_fs_ls_low_power(core_if,
-+ dwc_param_host_support_fs_ls_low_power_default);
-+ dwc_otg_set_param_enable_dynamic_fifo(core_if,
-+ dwc_param_enable_dynamic_fifo_default);
-+ dwc_otg_set_param_data_fifo_size(core_if,
-+ dwc_param_data_fifo_size_default);
-+ dwc_otg_set_param_dev_rx_fifo_size(core_if,
-+ dwc_param_dev_rx_fifo_size_default);
-+ dwc_otg_set_param_dev_nperio_tx_fifo_size(core_if,
-+ dwc_param_dev_nperio_tx_fifo_size_default);
-+ dwc_otg_set_param_host_rx_fifo_size(core_if,
-+ dwc_param_host_rx_fifo_size_default);
-+ dwc_otg_set_param_host_nperio_tx_fifo_size(core_if,
-+ dwc_param_host_nperio_tx_fifo_size_default);
-+ dwc_otg_set_param_host_perio_tx_fifo_size(core_if,
-+ dwc_param_host_perio_tx_fifo_size_default);
-+ dwc_otg_set_param_max_transfer_size(core_if,
-+ dwc_param_max_transfer_size_default);
-+ dwc_otg_set_param_max_packet_count(core_if,
-+ dwc_param_max_packet_count_default);
-+ dwc_otg_set_param_host_channels(core_if,
-+ dwc_param_host_channels_default);
-+ dwc_otg_set_param_dev_endpoints(core_if,
-+ dwc_param_dev_endpoints_default);
-+ dwc_otg_set_param_phy_type(core_if, dwc_param_phy_type_default);
-+ dwc_otg_set_param_speed(core_if, dwc_param_speed_default);
-+ dwc_otg_set_param_host_ls_low_power_phy_clk(core_if,
-+ dwc_param_host_ls_low_power_phy_clk_default);
-+ dwc_otg_set_param_phy_ulpi_ddr(core_if, dwc_param_phy_ulpi_ddr_default);
-+ dwc_otg_set_param_phy_ulpi_ext_vbus(core_if,
-+ dwc_param_phy_ulpi_ext_vbus_default);
-+ dwc_otg_set_param_phy_utmi_width(core_if,
-+ dwc_param_phy_utmi_width_default);
-+ dwc_otg_set_param_ts_dline(core_if, dwc_param_ts_dline_default);
-+ dwc_otg_set_param_i2c_enable(core_if, dwc_param_i2c_enable_default);
-+ dwc_otg_set_param_ulpi_fs_ls(core_if, dwc_param_ulpi_fs_ls_default);
-+ dwc_otg_set_param_en_multiple_tx_fifo(core_if,
-+ dwc_param_en_multiple_tx_fifo_default);
-+ for (i = 0; i < 15; i++) {
-+ dwc_otg_set_param_dev_perio_tx_fifo_size(core_if,
-+ dwc_param_dev_perio_tx_fifo_size_default,
-+ i);
-+ }
-+
-+ for (i = 0; i < 15; i++) {
-+ dwc_otg_set_param_dev_tx_fifo_size(core_if,
-+ dwc_param_dev_tx_fifo_size_default,
-+ i);
-+ }
-+ dwc_otg_set_param_thr_ctl(core_if, dwc_param_thr_ctl_default);
-+ dwc_otg_set_param_mpi_enable(core_if, dwc_param_mpi_enable_default);
-+ dwc_otg_set_param_pti_enable(core_if, dwc_param_pti_enable_default);
-+ dwc_otg_set_param_lpm_enable(core_if, dwc_param_lpm_enable_default);
-+ dwc_otg_set_param_ic_usb_cap(core_if, dwc_param_ic_usb_cap_default);
-+ dwc_otg_set_param_tx_thr_length(core_if,
-+ dwc_param_tx_thr_length_default);
-+ dwc_otg_set_param_rx_thr_length(core_if,
-+ dwc_param_rx_thr_length_default);
-+ dwc_otg_set_param_ahb_thr_ratio(core_if,
-+ dwc_param_ahb_thr_ratio_default);
-+ dwc_otg_set_param_power_down(core_if, dwc_param_power_down_default);
-+ dwc_otg_set_param_reload_ctl(core_if, dwc_param_reload_ctl_default);
-+ dwc_otg_set_param_dev_out_nak(core_if, dwc_param_dev_out_nak_default);
-+ dwc_otg_set_param_cont_on_bna(core_if, dwc_param_cont_on_bna_default);
-+ dwc_otg_set_param_ahb_single(core_if, dwc_param_ahb_single_default);
-+ dwc_otg_set_param_otg_ver(core_if, dwc_param_otg_ver_default);
-+ dwc_otg_set_param_adp_enable(core_if, dwc_param_adp_enable_default);
-+ DWC_PRINTF("Finished setting default values for core params\n");
-+
-+ return 0;
-+}
-+
-+uint8_t dwc_otg_is_dma_enable(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->dma_enable;
-+}
-+
-+/* Checks if the parameter is outside of its valid range of values */
-+#define DWC_OTG_PARAM_TEST(_param_, _low_, _high_) \
-+ (((_param_) < (_low_)) || \
-+ ((_param_) > (_high_)))
-+
-+/* Parameter access functions */
-+int dwc_otg_set_param_otg_cap(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ int valid;
-+ int retval = 0;
-+ if (DWC_OTG_PARAM_TEST(val, 0, 2)) {
-+ DWC_WARN("Wrong value for otg_cap parameter\n");
-+ DWC_WARN("otg_cap parameter must be 0,1 or 2\n");
-+ retval = -DWC_E_INVALID;
-+ goto out;
-+ }
-+
-+ valid = 1;
-+ switch (val) {
-+ case DWC_OTG_CAP_PARAM_HNP_SRP_CAPABLE:
-+ if (core_if->hwcfg2.b.op_mode !=
-+ DWC_HWCFG2_OP_MODE_HNP_SRP_CAPABLE_OTG)
-+ valid = 0;
-+ break;
-+ case DWC_OTG_CAP_PARAM_SRP_ONLY_CAPABLE:
-+ if ((core_if->hwcfg2.b.op_mode !=
-+ DWC_HWCFG2_OP_MODE_HNP_SRP_CAPABLE_OTG)
-+ && (core_if->hwcfg2.b.op_mode !=
-+ DWC_HWCFG2_OP_MODE_SRP_ONLY_CAPABLE_OTG)
-+ && (core_if->hwcfg2.b.op_mode !=
-+ DWC_HWCFG2_OP_MODE_SRP_CAPABLE_DEVICE)
-+ && (core_if->hwcfg2.b.op_mode !=
-+ DWC_HWCFG2_OP_MODE_SRP_CAPABLE_HOST)) {
-+ valid = 0;
-+ }
-+ break;
-+ case DWC_OTG_CAP_PARAM_NO_HNP_SRP_CAPABLE:
-+ /* always valid */
-+ break;
-+ }
-+ if (!valid) {
-+ if (dwc_otg_param_initialized(core_if->core_params->otg_cap)) {
-+ DWC_ERROR
-+ ("%d invalid for otg_cap paremter. Check HW configuration.\n",
-+ val);
-+ }
-+ val =
-+ (((core_if->hwcfg2.b.op_mode ==
-+ DWC_HWCFG2_OP_MODE_HNP_SRP_CAPABLE_OTG)
-+ || (core_if->hwcfg2.b.op_mode ==
-+ DWC_HWCFG2_OP_MODE_SRP_ONLY_CAPABLE_OTG)
-+ || (core_if->hwcfg2.b.op_mode ==
-+ DWC_HWCFG2_OP_MODE_SRP_CAPABLE_DEVICE)
-+ || (core_if->hwcfg2.b.op_mode ==
-+ DWC_HWCFG2_OP_MODE_SRP_CAPABLE_HOST)) ?
-+ DWC_OTG_CAP_PARAM_SRP_ONLY_CAPABLE :
-+ DWC_OTG_CAP_PARAM_NO_HNP_SRP_CAPABLE);
-+ retval = -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->otg_cap = val;
-+out:
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_otg_cap(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->otg_cap;
-+}
-+
-+int dwc_otg_set_param_opt(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ if (DWC_OTG_PARAM_TEST(val, 0, 1)) {
-+ DWC_WARN("Wrong value for opt parameter\n");
-+ return -DWC_E_INVALID;
-+ }
-+ core_if->core_params->opt = val;
-+ return 0;
-+}
-+
-+int32_t dwc_otg_get_param_opt(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->opt;
-+}
-+
-+int dwc_otg_set_param_dma_enable(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ int retval = 0;
-+ if (DWC_OTG_PARAM_TEST(val, 0, 1)) {
-+ DWC_WARN("Wrong value for dma enable\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if ((val == 1) && (core_if->hwcfg2.b.architecture == 0)) {
-+ if (dwc_otg_param_initialized(core_if->core_params->dma_enable)) {
-+ DWC_ERROR
-+ ("%d invalid for dma_enable paremter. Check HW configuration.\n",
-+ val);
-+ }
-+ val = 0;
-+ retval = -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->dma_enable = val;
-+ if (val == 0) {
-+ dwc_otg_set_param_dma_desc_enable(core_if, 0);
-+ }
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_dma_enable(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->dma_enable;
-+}
-+
-+int dwc_otg_set_param_dma_desc_enable(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ int retval = 0;
-+ if (DWC_OTG_PARAM_TEST(val, 0, 1)) {
-+ DWC_WARN("Wrong value for dma_enable\n");
-+ DWC_WARN("dma_desc_enable must be 0 or 1\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if ((val == 1)
-+ && ((dwc_otg_get_param_dma_enable(core_if) == 0)
-+ || (core_if->hwcfg4.b.desc_dma == 0))) {
-+ if (dwc_otg_param_initialized
-+ (core_if->core_params->dma_desc_enable)) {
-+ DWC_ERROR
-+ ("%d invalid for dma_desc_enable paremter. Check HW configuration.\n",
-+ val);
-+ }
-+ val = 0;
-+ retval = -DWC_E_INVALID;
-+ }
-+ core_if->core_params->dma_desc_enable = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_dma_desc_enable(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->dma_desc_enable;
-+}
-+
-+int dwc_otg_set_param_host_support_fs_ls_low_power(dwc_otg_core_if_t * core_if,
-+ int32_t val)
-+{
-+ if (DWC_OTG_PARAM_TEST(val, 0, 1)) {
-+ DWC_WARN("Wrong value for host_support_fs_low_power\n");
-+ DWC_WARN("host_support_fs_low_power must be 0 or 1\n");
-+ return -DWC_E_INVALID;
-+ }
-+ core_if->core_params->host_support_fs_ls_low_power = val;
-+ return 0;
-+}
-+
-+int32_t dwc_otg_get_param_host_support_fs_ls_low_power(dwc_otg_core_if_t *
-+ core_if)
-+{
-+ return core_if->core_params->host_support_fs_ls_low_power;
-+}
-+
-+int dwc_otg_set_param_enable_dynamic_fifo(dwc_otg_core_if_t * core_if,
-+ int32_t val)
-+{
-+ int retval = 0;
-+ if (DWC_OTG_PARAM_TEST(val, 0, 1)) {
-+ DWC_WARN("Wrong value for enable_dynamic_fifo\n");
-+ DWC_WARN("enable_dynamic_fifo must be 0 or 1\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if ((val == 1) && (core_if->hwcfg2.b.dynamic_fifo == 0)) {
-+ if (dwc_otg_param_initialized
-+ (core_if->core_params->enable_dynamic_fifo)) {
-+ DWC_ERROR
-+ ("%d invalid for enable_dynamic_fifo paremter. Check HW configuration.\n",
-+ val);
-+ }
-+ val = 0;
-+ retval = -DWC_E_INVALID;
-+ }
-+ core_if->core_params->enable_dynamic_fifo = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_enable_dynamic_fifo(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->enable_dynamic_fifo;
-+}
-+
-+int dwc_otg_set_param_data_fifo_size(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ int retval = 0;
-+ if (DWC_OTG_PARAM_TEST(val, 32, 32768)) {
-+ DWC_WARN("Wrong value for data_fifo_size\n");
-+ DWC_WARN("data_fifo_size must be 32-32768\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if (val > core_if->hwcfg3.b.dfifo_depth) {
-+ if (dwc_otg_param_initialized
-+ (core_if->core_params->data_fifo_size)) {
-+ DWC_ERROR
-+ ("%d invalid for data_fifo_size parameter. Check HW configuration.\n",
-+ val);
-+ }
-+ val = core_if->hwcfg3.b.dfifo_depth;
-+ retval = -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->data_fifo_size = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_data_fifo_size(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->data_fifo_size;
-+}
-+
-+int dwc_otg_set_param_dev_rx_fifo_size(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ int retval = 0;
-+ if (DWC_OTG_PARAM_TEST(val, 16, 32768)) {
-+ DWC_WARN("Wrong value for dev_rx_fifo_size\n");
-+ DWC_WARN("dev_rx_fifo_size must be 16-32768\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if (val > DWC_READ_REG32(&core_if->core_global_regs->grxfsiz)) {
-+ if (dwc_otg_param_initialized(core_if->core_params->dev_rx_fifo_size)) {
-+ DWC_WARN("%d invalid for dev_rx_fifo_size parameter\n", val);
-+ }
-+ val = DWC_READ_REG32(&core_if->core_global_regs->grxfsiz);
-+ retval = -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->dev_rx_fifo_size = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_dev_rx_fifo_size(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->dev_rx_fifo_size;
-+}
-+
-+int dwc_otg_set_param_dev_nperio_tx_fifo_size(dwc_otg_core_if_t * core_if,
-+ int32_t val)
-+{
-+ int retval = 0;
-+
-+ if (DWC_OTG_PARAM_TEST(val, 16, 32768)) {
-+ DWC_WARN("Wrong value for dev_nperio_tx_fifo\n");
-+ DWC_WARN("dev_nperio_tx_fifo must be 16-32768\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if (val > (DWC_READ_REG32(&core_if->core_global_regs->gnptxfsiz) >> 16)) {
-+ if (dwc_otg_param_initialized
-+ (core_if->core_params->dev_nperio_tx_fifo_size)) {
-+ DWC_ERROR
-+ ("%d invalid for dev_nperio_tx_fifo_size. Check HW configuration.\n",
-+ val);
-+ }
-+ val =
-+ (DWC_READ_REG32(&core_if->core_global_regs->gnptxfsiz) >>
-+ 16);
-+ retval = -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->dev_nperio_tx_fifo_size = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_dev_nperio_tx_fifo_size(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->dev_nperio_tx_fifo_size;
-+}
-+
-+int dwc_otg_set_param_host_rx_fifo_size(dwc_otg_core_if_t * core_if,
-+ int32_t val)
-+{
-+ int retval = 0;
-+
-+ if (DWC_OTG_PARAM_TEST(val, 16, 32768)) {
-+ DWC_WARN("Wrong value for host_rx_fifo_size\n");
-+ DWC_WARN("host_rx_fifo_size must be 16-32768\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if (val > DWC_READ_REG32(&core_if->core_global_regs->grxfsiz)) {
-+ if (dwc_otg_param_initialized
-+ (core_if->core_params->host_rx_fifo_size)) {
-+ DWC_ERROR
-+ ("%d invalid for host_rx_fifo_size. Check HW configuration.\n",
-+ val);
-+ }
-+ val = DWC_READ_REG32(&core_if->core_global_regs->grxfsiz);
-+ retval = -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->host_rx_fifo_size = val;
-+ return retval;
-+
-+}
-+
-+int32_t dwc_otg_get_param_host_rx_fifo_size(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->host_rx_fifo_size;
-+}
-+
-+int dwc_otg_set_param_host_nperio_tx_fifo_size(dwc_otg_core_if_t * core_if,
-+ int32_t val)
-+{
-+ int retval = 0;
-+
-+ if (DWC_OTG_PARAM_TEST(val, 16, 32768)) {
-+ DWC_WARN("Wrong value for host_nperio_tx_fifo_size\n");
-+ DWC_WARN("host_nperio_tx_fifo_size must be 16-32768\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if (val > (DWC_READ_REG32(&core_if->core_global_regs->gnptxfsiz) >> 16)) {
-+ if (dwc_otg_param_initialized
-+ (core_if->core_params->host_nperio_tx_fifo_size)) {
-+ DWC_ERROR
-+ ("%d invalid for host_nperio_tx_fifo_size. Check HW configuration.\n",
-+ val);
-+ }
-+ val =
-+ (DWC_READ_REG32(&core_if->core_global_regs->gnptxfsiz) >>
-+ 16);
-+ retval = -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->host_nperio_tx_fifo_size = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_host_nperio_tx_fifo_size(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->host_nperio_tx_fifo_size;
-+}
-+
-+int dwc_otg_set_param_host_perio_tx_fifo_size(dwc_otg_core_if_t * core_if,
-+ int32_t val)
-+{
-+ int retval = 0;
-+ if (DWC_OTG_PARAM_TEST(val, 16, 32768)) {
-+ DWC_WARN("Wrong value for host_perio_tx_fifo_size\n");
-+ DWC_WARN("host_perio_tx_fifo_size must be 16-32768\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if (val > ((core_if->hptxfsiz.d32) >> 16)) {
-+ if (dwc_otg_param_initialized
-+ (core_if->core_params->host_perio_tx_fifo_size)) {
-+ DWC_ERROR
-+ ("%d invalid for host_perio_tx_fifo_size. Check HW configuration.\n",
-+ val);
-+ }
-+ val = (core_if->hptxfsiz.d32) >> 16;
-+ retval = -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->host_perio_tx_fifo_size = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_host_perio_tx_fifo_size(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->host_perio_tx_fifo_size;
-+}
-+
-+int dwc_otg_set_param_max_transfer_size(dwc_otg_core_if_t * core_if,
-+ int32_t val)
-+{
-+ int retval = 0;
-+
-+ if (DWC_OTG_PARAM_TEST(val, 2047, 524288)) {
-+ DWC_WARN("Wrong value for max_transfer_size\n");
-+ DWC_WARN("max_transfer_size must be 2047-524288\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if (val >= (1 << (core_if->hwcfg3.b.xfer_size_cntr_width + 11))) {
-+ if (dwc_otg_param_initialized
-+ (core_if->core_params->max_transfer_size)) {
-+ DWC_ERROR
-+ ("%d invalid for max_transfer_size. Check HW configuration.\n",
-+ val);
-+ }
-+ val =
-+ ((1 << (core_if->hwcfg3.b.packet_size_cntr_width + 11)) -
-+ 1);
-+ retval = -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->max_transfer_size = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_max_transfer_size(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->max_transfer_size;
-+}
-+
-+int dwc_otg_set_param_max_packet_count(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ int retval = 0;
-+
-+ if (DWC_OTG_PARAM_TEST(val, 15, 511)) {
-+ DWC_WARN("Wrong value for max_packet_count\n");
-+ DWC_WARN("max_packet_count must be 15-511\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if (val > (1 << (core_if->hwcfg3.b.packet_size_cntr_width + 4))) {
-+ if (dwc_otg_param_initialized
-+ (core_if->core_params->max_packet_count)) {
-+ DWC_ERROR
-+ ("%d invalid for max_packet_count. Check HW configuration.\n",
-+ val);
-+ }
-+ val =
-+ ((1 << (core_if->hwcfg3.b.packet_size_cntr_width + 4)) - 1);
-+ retval = -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->max_packet_count = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_max_packet_count(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->max_packet_count;
-+}
-+
-+int dwc_otg_set_param_host_channels(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ int retval = 0;
-+
-+ if (DWC_OTG_PARAM_TEST(val, 1, 16)) {
-+ DWC_WARN("Wrong value for host_channels\n");
-+ DWC_WARN("host_channels must be 1-16\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if (val > (core_if->hwcfg2.b.num_host_chan + 1)) {
-+ if (dwc_otg_param_initialized
-+ (core_if->core_params->host_channels)) {
-+ DWC_ERROR
-+ ("%d invalid for host_channels. Check HW configurations.\n",
-+ val);
-+ }
-+ val = (core_if->hwcfg2.b.num_host_chan + 1);
-+ retval = -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->host_channels = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_host_channels(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->host_channels;
-+}
-+
-+int dwc_otg_set_param_dev_endpoints(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ int retval = 0;
-+
-+ if (DWC_OTG_PARAM_TEST(val, 1, 15)) {
-+ DWC_WARN("Wrong value for dev_endpoints\n");
-+ DWC_WARN("dev_endpoints must be 1-15\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if (val > (core_if->hwcfg2.b.num_dev_ep)) {
-+ if (dwc_otg_param_initialized
-+ (core_if->core_params->dev_endpoints)) {
-+ DWC_ERROR
-+ ("%d invalid for dev_endpoints. Check HW configurations.\n",
-+ val);
-+ }
-+ val = core_if->hwcfg2.b.num_dev_ep;
-+ retval = -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->dev_endpoints = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_dev_endpoints(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->dev_endpoints;
-+}
-+
-+int dwc_otg_set_param_phy_type(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ int retval = 0;
-+ int valid = 0;
-+
-+ if (DWC_OTG_PARAM_TEST(val, 0, 2)) {
-+ DWC_WARN("Wrong value for phy_type\n");
-+ DWC_WARN("phy_type must be 0,1 or 2\n");
-+ return -DWC_E_INVALID;
-+ }
-+#ifndef NO_FS_PHY_HW_CHECKS
-+ if ((val == DWC_PHY_TYPE_PARAM_UTMI) &&
-+ ((core_if->hwcfg2.b.hs_phy_type == 1) ||
-+ (core_if->hwcfg2.b.hs_phy_type == 3))) {
-+ valid = 1;
-+ } else if ((val == DWC_PHY_TYPE_PARAM_ULPI) &&
-+ ((core_if->hwcfg2.b.hs_phy_type == 2) ||
-+ (core_if->hwcfg2.b.hs_phy_type == 3))) {
-+ valid = 1;
-+ } else if ((val == DWC_PHY_TYPE_PARAM_FS) &&
-+ (core_if->hwcfg2.b.fs_phy_type == 1)) {
-+ valid = 1;
-+ }
-+ if (!valid) {
-+ if (dwc_otg_param_initialized(core_if->core_params->phy_type)) {
-+ DWC_ERROR
-+ ("%d invalid for phy_type. Check HW configurations.\n",
-+ val);
-+ }
-+ if (core_if->hwcfg2.b.hs_phy_type) {
-+ if ((core_if->hwcfg2.b.hs_phy_type == 3) ||
-+ (core_if->hwcfg2.b.hs_phy_type == 1)) {
-+ val = DWC_PHY_TYPE_PARAM_UTMI;
-+ } else {
-+ val = DWC_PHY_TYPE_PARAM_ULPI;
-+ }
-+ }
-+ retval = -DWC_E_INVALID;
-+ }
-+#endif
-+ core_if->core_params->phy_type = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_phy_type(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->phy_type;
-+}
-+
-+int dwc_otg_set_param_speed(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ int retval = 0;
-+ if (DWC_OTG_PARAM_TEST(val, 0, 1)) {
-+ DWC_WARN("Wrong value for speed parameter\n");
-+ DWC_WARN("max_speed parameter must be 0 or 1\n");
-+ return -DWC_E_INVALID;
-+ }
-+ if ((val == 0)
-+ && dwc_otg_get_param_phy_type(core_if) == DWC_PHY_TYPE_PARAM_FS) {
-+ if (dwc_otg_param_initialized(core_if->core_params->speed)) {
-+ DWC_ERROR
-+ ("%d invalid for speed paremter. Check HW configuration.\n",
-+ val);
-+ }
-+ val =
-+ (dwc_otg_get_param_phy_type(core_if) ==
-+ DWC_PHY_TYPE_PARAM_FS ? 1 : 0);
-+ retval = -DWC_E_INVALID;
-+ }
-+ core_if->core_params->speed = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_speed(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->speed;
-+}
-+
-+int dwc_otg_set_param_host_ls_low_power_phy_clk(dwc_otg_core_if_t * core_if,
-+ int32_t val)
-+{
-+ int retval = 0;
-+
-+ if (DWC_OTG_PARAM_TEST(val, 0, 1)) {
-+ DWC_WARN
-+ ("Wrong value for host_ls_low_power_phy_clk parameter\n");
-+ DWC_WARN("host_ls_low_power_phy_clk must be 0 or 1\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if ((val == DWC_HOST_LS_LOW_POWER_PHY_CLK_PARAM_48MHZ)
-+ && (dwc_otg_get_param_phy_type(core_if) == DWC_PHY_TYPE_PARAM_FS)) {
-+ if (dwc_otg_param_initialized
-+ (core_if->core_params->host_ls_low_power_phy_clk)) {
-+ DWC_ERROR
-+ ("%d invalid for host_ls_low_power_phy_clk. Check HW configuration.\n",
-+ val);
-+ }
-+ val =
-+ (dwc_otg_get_param_phy_type(core_if) ==
-+ DWC_PHY_TYPE_PARAM_FS) ?
-+ DWC_HOST_LS_LOW_POWER_PHY_CLK_PARAM_6MHZ :
-+ DWC_HOST_LS_LOW_POWER_PHY_CLK_PARAM_48MHZ;
-+ retval = -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->host_ls_low_power_phy_clk = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_host_ls_low_power_phy_clk(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->host_ls_low_power_phy_clk;
-+}
-+
-+int dwc_otg_set_param_phy_ulpi_ddr(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ if (DWC_OTG_PARAM_TEST(val, 0, 1)) {
-+ DWC_WARN("Wrong value for phy_ulpi_ddr\n");
-+ DWC_WARN("phy_upli_ddr must be 0 or 1\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->phy_ulpi_ddr = val;
-+ return 0;
-+}
-+
-+int32_t dwc_otg_get_param_phy_ulpi_ddr(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->phy_ulpi_ddr;
-+}
-+
-+int dwc_otg_set_param_phy_ulpi_ext_vbus(dwc_otg_core_if_t * core_if,
-+ int32_t val)
-+{
-+ if (DWC_OTG_PARAM_TEST(val, 0, 1)) {
-+ DWC_WARN("Wrong valaue for phy_ulpi_ext_vbus\n");
-+ DWC_WARN("phy_ulpi_ext_vbus must be 0 or 1\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->phy_ulpi_ext_vbus = val;
-+ return 0;
-+}
-+
-+int32_t dwc_otg_get_param_phy_ulpi_ext_vbus(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->phy_ulpi_ext_vbus;
-+}
-+
-+int dwc_otg_set_param_phy_utmi_width(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ if (DWC_OTG_PARAM_TEST(val, 8, 8) && DWC_OTG_PARAM_TEST(val, 16, 16)) {
-+ DWC_WARN("Wrong valaue for phy_utmi_width\n");
-+ DWC_WARN("phy_utmi_width must be 8 or 16\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->phy_utmi_width = val;
-+ return 0;
-+}
-+
-+int32_t dwc_otg_get_param_phy_utmi_width(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->phy_utmi_width;
-+}
-+
-+int dwc_otg_set_param_ulpi_fs_ls(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ if (DWC_OTG_PARAM_TEST(val, 0, 1)) {
-+ DWC_WARN("Wrong valaue for ulpi_fs_ls\n");
-+ DWC_WARN("ulpi_fs_ls must be 0 or 1\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->ulpi_fs_ls = val;
-+ return 0;
-+}
-+
-+int32_t dwc_otg_get_param_ulpi_fs_ls(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->ulpi_fs_ls;
-+}
-+
-+int dwc_otg_set_param_ts_dline(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ if (DWC_OTG_PARAM_TEST(val, 0, 1)) {
-+ DWC_WARN("Wrong valaue for ts_dline\n");
-+ DWC_WARN("ts_dline must be 0 or 1\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->ts_dline = val;
-+ return 0;
-+}
-+
-+int32_t dwc_otg_get_param_ts_dline(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->ts_dline;
-+}
-+
-+int dwc_otg_set_param_i2c_enable(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ int retval = 0;
-+ if (DWC_OTG_PARAM_TEST(val, 0, 1)) {
-+ DWC_WARN("Wrong valaue for i2c_enable\n");
-+ DWC_WARN("i2c_enable must be 0 or 1\n");
-+ return -DWC_E_INVALID;
-+ }
-+#ifndef NO_FS_PHY_HW_CHECK
-+ if (val == 1 && core_if->hwcfg3.b.i2c == 0) {
-+ if (dwc_otg_param_initialized(core_if->core_params->i2c_enable)) {
-+ DWC_ERROR
-+ ("%d invalid for i2c_enable. Check HW configuration.\n",
-+ val);
-+ }
-+ val = 0;
-+ retval = -DWC_E_INVALID;
-+ }
-+#endif
-+
-+ core_if->core_params->i2c_enable = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_i2c_enable(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->i2c_enable;
-+}
-+
-+int dwc_otg_set_param_dev_perio_tx_fifo_size(dwc_otg_core_if_t * core_if,
-+ int32_t val, int fifo_num)
-+{
-+ int retval = 0;
-+
-+ if (DWC_OTG_PARAM_TEST(val, 4, 768)) {
-+ DWC_WARN("Wrong value for dev_perio_tx_fifo_size\n");
-+ DWC_WARN("dev_perio_tx_fifo_size must be 4-768\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if (val >
-+ (DWC_READ_REG32(&core_if->core_global_regs->dtxfsiz[fifo_num]))) {
-+ if (dwc_otg_param_initialized
-+ (core_if->core_params->dev_perio_tx_fifo_size[fifo_num])) {
-+ DWC_ERROR
-+ ("`%d' invalid for parameter `dev_perio_fifo_size_%d'. Check HW configuration.\n",
-+ val, fifo_num);
-+ }
-+ val = (DWC_READ_REG32(&core_if->core_global_regs->dtxfsiz[fifo_num]));
-+ retval = -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->dev_perio_tx_fifo_size[fifo_num] = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_dev_perio_tx_fifo_size(dwc_otg_core_if_t * core_if,
-+ int fifo_num)
-+{
-+ return core_if->core_params->dev_perio_tx_fifo_size[fifo_num];
-+}
-+
-+int dwc_otg_set_param_en_multiple_tx_fifo(dwc_otg_core_if_t * core_if,
-+ int32_t val)
-+{
-+ int retval = 0;
-+ if (DWC_OTG_PARAM_TEST(val, 0, 1)) {
-+ DWC_WARN("Wrong valaue for en_multiple_tx_fifo,\n");
-+ DWC_WARN("en_multiple_tx_fifo must be 0 or 1\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if (val == 1 && core_if->hwcfg4.b.ded_fifo_en == 0) {
-+ if (dwc_otg_param_initialized
-+ (core_if->core_params->en_multiple_tx_fifo)) {
-+ DWC_ERROR
-+ ("%d invalid for parameter en_multiple_tx_fifo. Check HW configuration.\n",
-+ val);
-+ }
-+ val = 0;
-+ retval = -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->en_multiple_tx_fifo = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_en_multiple_tx_fifo(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->en_multiple_tx_fifo;
-+}
-+
-+int dwc_otg_set_param_dev_tx_fifo_size(dwc_otg_core_if_t * core_if, int32_t val,
-+ int fifo_num)
-+{
-+ int retval = 0;
-+
-+ if (DWC_OTG_PARAM_TEST(val, 4, 768)) {
-+ DWC_WARN("Wrong value for dev_tx_fifo_size\n");
-+ DWC_WARN("dev_tx_fifo_size must be 4-768\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if (val >
-+ (DWC_READ_REG32(&core_if->core_global_regs->dtxfsiz[fifo_num]))) {
-+ if (dwc_otg_param_initialized
-+ (core_if->core_params->dev_tx_fifo_size[fifo_num])) {
-+ DWC_ERROR
-+ ("`%d' invalid for parameter `dev_tx_fifo_size_%d'. Check HW configuration.\n",
-+ val, fifo_num);
-+ }
-+ val = (DWC_READ_REG32(&core_if->core_global_regs->dtxfsiz[fifo_num]));
-+ retval = -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->dev_tx_fifo_size[fifo_num] = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_dev_tx_fifo_size(dwc_otg_core_if_t * core_if,
-+ int fifo_num)
-+{
-+ return core_if->core_params->dev_tx_fifo_size[fifo_num];
-+}
-+
-+int dwc_otg_set_param_thr_ctl(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ int retval = 0;
-+
-+ if (DWC_OTG_PARAM_TEST(val, 0, 7)) {
-+ DWC_WARN("Wrong value for thr_ctl\n");
-+ DWC_WARN("thr_ctl must be 0-7\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if ((val != 0) &&
-+ (!dwc_otg_get_param_dma_enable(core_if) ||
-+ !core_if->hwcfg4.b.ded_fifo_en)) {
-+ if (dwc_otg_param_initialized(core_if->core_params->thr_ctl)) {
-+ DWC_ERROR
-+ ("%d invalid for parameter thr_ctl. Check HW configuration.\n",
-+ val);
-+ }
-+ val = 0;
-+ retval = -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->thr_ctl = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_thr_ctl(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->thr_ctl;
-+}
-+
-+int dwc_otg_set_param_lpm_enable(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ int retval = 0;
-+
-+ if (DWC_OTG_PARAM_TEST(val, 0, 1)) {
-+ DWC_WARN("Wrong value for lpm_enable\n");
-+ DWC_WARN("lpm_enable must be 0 or 1\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if (val && !core_if->hwcfg3.b.otg_lpm_en) {
-+ if (dwc_otg_param_initialized(core_if->core_params->lpm_enable)) {
-+ DWC_ERROR
-+ ("%d invalid for parameter lpm_enable. Check HW configuration.\n",
-+ val);
-+ }
-+ val = 0;
-+ retval = -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->lpm_enable = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_lpm_enable(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->lpm_enable;
-+}
-+
-+int dwc_otg_set_param_tx_thr_length(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ if (DWC_OTG_PARAM_TEST(val, 8, 128)) {
-+ DWC_WARN("Wrong valaue for tx_thr_length\n");
-+ DWC_WARN("tx_thr_length must be 8 - 128\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->tx_thr_length = val;
-+ return 0;
-+}
-+
-+int32_t dwc_otg_get_param_tx_thr_length(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->tx_thr_length;
-+}
-+
-+int dwc_otg_set_param_rx_thr_length(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ if (DWC_OTG_PARAM_TEST(val, 8, 128)) {
-+ DWC_WARN("Wrong valaue for rx_thr_length\n");
-+ DWC_WARN("rx_thr_length must be 8 - 128\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->rx_thr_length = val;
-+ return 0;
-+}
-+
-+int32_t dwc_otg_get_param_rx_thr_length(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->rx_thr_length;
-+}
-+
-+int dwc_otg_set_param_dma_burst_size(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ if (DWC_OTG_PARAM_TEST(val, 1, 1) &&
-+ DWC_OTG_PARAM_TEST(val, 4, 4) &&
-+ DWC_OTG_PARAM_TEST(val, 8, 8) &&
-+ DWC_OTG_PARAM_TEST(val, 16, 16) &&
-+ DWC_OTG_PARAM_TEST(val, 32, 32) &&
-+ DWC_OTG_PARAM_TEST(val, 64, 64) &&
-+ DWC_OTG_PARAM_TEST(val, 128, 128) &&
-+ DWC_OTG_PARAM_TEST(val, 256, 256)) {
-+ DWC_WARN("`%d' invalid for parameter `dma_burst_size'\n", val);
-+ return -DWC_E_INVALID;
-+ }
-+ core_if->core_params->dma_burst_size = val;
-+ return 0;
-+}
-+
-+int32_t dwc_otg_get_param_dma_burst_size(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->dma_burst_size;
-+}
-+
-+int dwc_otg_set_param_pti_enable(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ int retval = 0;
-+ if (DWC_OTG_PARAM_TEST(val, 0, 1)) {
-+ DWC_WARN("`%d' invalid for parameter `pti_enable'\n", val);
-+ return -DWC_E_INVALID;
-+ }
-+ if (val && (core_if->snpsid < OTG_CORE_REV_2_72a)) {
-+ if (dwc_otg_param_initialized(core_if->core_params->pti_enable)) {
-+ DWC_ERROR
-+ ("%d invalid for parameter pti_enable. Check HW configuration.\n",
-+ val);
-+ }
-+ retval = -DWC_E_INVALID;
-+ val = 0;
-+ }
-+ core_if->core_params->pti_enable = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_pti_enable(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->pti_enable;
-+}
-+
-+int dwc_otg_set_param_mpi_enable(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ int retval = 0;
-+ if (DWC_OTG_PARAM_TEST(val, 0, 1)) {
-+ DWC_WARN("`%d' invalid for parameter `mpi_enable'\n", val);
-+ return -DWC_E_INVALID;
-+ }
-+ if (val && (core_if->hwcfg2.b.multi_proc_int == 0)) {
-+ if (dwc_otg_param_initialized(core_if->core_params->mpi_enable)) {
-+ DWC_ERROR
-+ ("%d invalid for parameter mpi_enable. Check HW configuration.\n",
-+ val);
-+ }
-+ retval = -DWC_E_INVALID;
-+ val = 0;
-+ }
-+ core_if->core_params->mpi_enable = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_mpi_enable(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->mpi_enable;
-+}
-+
-+int dwc_otg_set_param_adp_enable(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ int retval = 0;
-+ if (DWC_OTG_PARAM_TEST(val, 0, 1)) {
-+ DWC_WARN("`%d' invalid for parameter `adp_enable'\n", val);
-+ return -DWC_E_INVALID;
-+ }
-+ if (val && (core_if->hwcfg3.b.adp_supp == 0)) {
-+ if (dwc_otg_param_initialized
-+ (core_if->core_params->adp_supp_enable)) {
-+ DWC_ERROR
-+ ("%d invalid for parameter adp_enable. Check HW configuration.\n",
-+ val);
-+ }
-+ retval = -DWC_E_INVALID;
-+ val = 0;
-+ }
-+ core_if->core_params->adp_supp_enable = val;
-+ /*Set OTG version 2.0 in case of enabling ADP*/
-+ if (val)
-+ dwc_otg_set_param_otg_ver(core_if, 1);
-+
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_adp_enable(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->adp_supp_enable;
-+}
-+
-+int dwc_otg_set_param_ic_usb_cap(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ int retval = 0;
-+ if (DWC_OTG_PARAM_TEST(val, 0, 1)) {
-+ DWC_WARN("`%d' invalid for parameter `ic_usb_cap'\n", val);
-+ DWC_WARN("ic_usb_cap must be 0 or 1\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if (val && (core_if->hwcfg2.b.otg_enable_ic_usb == 0)) {
-+ if (dwc_otg_param_initialized(core_if->core_params->ic_usb_cap)) {
-+ DWC_ERROR
-+ ("%d invalid for parameter ic_usb_cap. Check HW configuration.\n",
-+ val);
-+ }
-+ retval = -DWC_E_INVALID;
-+ val = 0;
-+ }
-+ core_if->core_params->ic_usb_cap = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_ic_usb_cap(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->ic_usb_cap;
-+}
-+
-+int dwc_otg_set_param_ahb_thr_ratio(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ int retval = 0;
-+ int valid = 1;
-+
-+ if (DWC_OTG_PARAM_TEST(val, 0, 3)) {
-+ DWC_WARN("`%d' invalid for parameter `ahb_thr_ratio'\n", val);
-+ DWC_WARN("ahb_thr_ratio must be 0 - 3\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if (val
-+ && (core_if->snpsid < OTG_CORE_REV_2_81a
-+ || !dwc_otg_get_param_thr_ctl(core_if))) {
-+ valid = 0;
-+ } else if (val
-+ && ((dwc_otg_get_param_tx_thr_length(core_if) / (1 << val)) <
-+ 4)) {
-+ valid = 0;
-+ }
-+ if (valid == 0) {
-+ if (dwc_otg_param_initialized
-+ (core_if->core_params->ahb_thr_ratio)) {
-+ DWC_ERROR
-+ ("%d invalid for parameter ahb_thr_ratio. Check HW configuration.\n",
-+ val);
-+ }
-+ retval = -DWC_E_INVALID;
-+ val = 0;
-+ }
-+
-+ core_if->core_params->ahb_thr_ratio = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_ahb_thr_ratio(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->ahb_thr_ratio;
-+}
-+
-+int dwc_otg_set_param_power_down(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ int retval = 0;
-+ int valid = 1;
-+ hwcfg4_data_t hwcfg4 = {.d32 = 0 };
-+ hwcfg4.d32 = DWC_READ_REG32(&core_if->core_global_regs->ghwcfg4);
-+
-+ if (DWC_OTG_PARAM_TEST(val, 0, 3)) {
-+ DWC_WARN("`%d' invalid for parameter `power_down'\n", val);
-+ DWC_WARN("power_down must be 0 - 2\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if ((val == 2) && (core_if->snpsid < OTG_CORE_REV_2_91a)) {
-+ valid = 0;
-+ }
-+ if ((val == 3)
-+ && ((core_if->snpsid < OTG_CORE_REV_3_00a)
-+ || (hwcfg4.b.xhiber == 0))) {
-+ valid = 0;
-+ }
-+ if (valid == 0) {
-+ if (dwc_otg_param_initialized(core_if->core_params->power_down)) {
-+ DWC_ERROR
-+ ("%d invalid for parameter power_down. Check HW configuration.\n",
-+ val);
-+ }
-+ retval = -DWC_E_INVALID;
-+ val = 0;
-+ }
-+ core_if->core_params->power_down = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_power_down(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->power_down;
-+}
-+
-+int dwc_otg_set_param_reload_ctl(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ int retval = 0;
-+ int valid = 1;
-+
-+ if (DWC_OTG_PARAM_TEST(val, 0, 1)) {
-+ DWC_WARN("`%d' invalid for parameter `reload_ctl'\n", val);
-+ DWC_WARN("reload_ctl must be 0 or 1\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if ((val == 1) && (core_if->snpsid < OTG_CORE_REV_2_92a)) {
-+ valid = 0;
-+ }
-+ if (valid == 0) {
-+ if (dwc_otg_param_initialized(core_if->core_params->reload_ctl)) {
-+ DWC_ERROR("%d invalid for parameter reload_ctl."
-+ "Check HW configuration.\n", val);
-+ }
-+ retval = -DWC_E_INVALID;
-+ val = 0;
-+ }
-+ core_if->core_params->reload_ctl = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_reload_ctl(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->reload_ctl;
-+}
-+
-+int dwc_otg_set_param_dev_out_nak(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ int retval = 0;
-+ int valid = 1;
-+
-+ if (DWC_OTG_PARAM_TEST(val, 0, 1)) {
-+ DWC_WARN("`%d' invalid for parameter `dev_out_nak'\n", val);
-+ DWC_WARN("dev_out_nak must be 0 or 1\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if ((val == 1) && ((core_if->snpsid < OTG_CORE_REV_2_93a) ||
-+ !(core_if->core_params->dma_desc_enable))) {
-+ valid = 0;
-+ }
-+ if (valid == 0) {
-+ if (dwc_otg_param_initialized(core_if->core_params->dev_out_nak)) {
-+ DWC_ERROR("%d invalid for parameter dev_out_nak."
-+ "Check HW configuration.\n", val);
-+ }
-+ retval = -DWC_E_INVALID;
-+ val = 0;
-+ }
-+ core_if->core_params->dev_out_nak = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_dev_out_nak(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->dev_out_nak;
-+}
-+
-+int dwc_otg_set_param_cont_on_bna(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ int retval = 0;
-+ int valid = 1;
-+
-+ if (DWC_OTG_PARAM_TEST(val, 0, 1)) {
-+ DWC_WARN("`%d' invalid for parameter `cont_on_bna'\n", val);
-+ DWC_WARN("cont_on_bna must be 0 or 1\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if ((val == 1) && ((core_if->snpsid < OTG_CORE_REV_2_94a) ||
-+ !(core_if->core_params->dma_desc_enable))) {
-+ valid = 0;
-+ }
-+ if (valid == 0) {
-+ if (dwc_otg_param_initialized(core_if->core_params->cont_on_bna)) {
-+ DWC_ERROR("%d invalid for parameter cont_on_bna."
-+ "Check HW configuration.\n", val);
-+ }
-+ retval = -DWC_E_INVALID;
-+ val = 0;
-+ }
-+ core_if->core_params->cont_on_bna = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_cont_on_bna(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->cont_on_bna;
-+}
-+
-+int dwc_otg_set_param_ahb_single(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ int retval = 0;
-+ int valid = 1;
-+
-+ if (DWC_OTG_PARAM_TEST(val, 0, 1)) {
-+ DWC_WARN("`%d' invalid for parameter `ahb_single'\n", val);
-+ DWC_WARN("ahb_single must be 0 or 1\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if ((val == 1) && (core_if->snpsid < OTG_CORE_REV_2_94a)) {
-+ valid = 0;
-+ }
-+ if (valid == 0) {
-+ if (dwc_otg_param_initialized(core_if->core_params->ahb_single)) {
-+ DWC_ERROR("%d invalid for parameter ahb_single."
-+ "Check HW configuration.\n", val);
-+ }
-+ retval = -DWC_E_INVALID;
-+ val = 0;
-+ }
-+ core_if->core_params->ahb_single = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_ahb_single(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->ahb_single;
-+}
-+
-+int dwc_otg_set_param_otg_ver(dwc_otg_core_if_t * core_if, int32_t val)
-+{
-+ int retval = 0;
-+
-+ if (DWC_OTG_PARAM_TEST(val, 0, 1)) {
-+ DWC_WARN("`%d' invalid for parameter `otg_ver'\n", val);
-+ DWC_WARN
-+ ("otg_ver must be 0(for OTG 1.3 support) or 1(for OTG 2.0 support)\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ core_if->core_params->otg_ver = val;
-+ return retval;
-+}
-+
-+int32_t dwc_otg_get_param_otg_ver(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->core_params->otg_ver;
-+}
-+
-+uint32_t dwc_otg_get_hnpstatus(dwc_otg_core_if_t * core_if)
-+{
-+ gotgctl_data_t otgctl;
-+ otgctl.d32 = DWC_READ_REG32(&core_if->core_global_regs->gotgctl);
-+ return otgctl.b.hstnegscs;
-+}
-+
-+uint32_t dwc_otg_get_srpstatus(dwc_otg_core_if_t * core_if)
-+{
-+ gotgctl_data_t otgctl;
-+ otgctl.d32 = DWC_READ_REG32(&core_if->core_global_regs->gotgctl);
-+ return otgctl.b.sesreqscs;
-+}
-+
-+void dwc_otg_set_hnpreq(dwc_otg_core_if_t * core_if, uint32_t val)
-+{
-+ if(core_if->otg_ver == 0) {
-+ gotgctl_data_t otgctl;
-+ otgctl.d32 = DWC_READ_REG32(&core_if->core_global_regs->gotgctl);
-+ otgctl.b.hnpreq = val;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gotgctl, otgctl.d32);
-+ } else {
-+ core_if->otg_sts = val;
-+ }
-+}
-+
-+uint32_t dwc_otg_get_gsnpsid(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->snpsid;
-+}
-+
-+uint32_t dwc_otg_get_mode(dwc_otg_core_if_t * core_if)
-+{
-+ gintsts_data_t gintsts;
-+ gintsts.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintsts);
-+ return gintsts.b.curmode;
-+}
-+
-+uint32_t dwc_otg_get_hnpcapable(dwc_otg_core_if_t * core_if)
-+{
-+ gusbcfg_data_t usbcfg;
-+ usbcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->gusbcfg);
-+ return usbcfg.b.hnpcap;
-+}
-+
-+void dwc_otg_set_hnpcapable(dwc_otg_core_if_t * core_if, uint32_t val)
-+{
-+ gusbcfg_data_t usbcfg;
-+ usbcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->gusbcfg);
-+ usbcfg.b.hnpcap = val;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gusbcfg, usbcfg.d32);
-+}
-+
-+uint32_t dwc_otg_get_srpcapable(dwc_otg_core_if_t * core_if)
-+{
-+ gusbcfg_data_t usbcfg;
-+ usbcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->gusbcfg);
-+ return usbcfg.b.srpcap;
-+}
-+
-+void dwc_otg_set_srpcapable(dwc_otg_core_if_t * core_if, uint32_t val)
-+{
-+ gusbcfg_data_t usbcfg;
-+ usbcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->gusbcfg);
-+ usbcfg.b.srpcap = val;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gusbcfg, usbcfg.d32);
-+}
-+
-+uint32_t dwc_otg_get_devspeed(dwc_otg_core_if_t * core_if)
-+{
-+ dcfg_data_t dcfg;
-+ /* originally: dcfg.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dcfg); */
-+
-+ dcfg.d32 = -1; //GRAYG
-+ DWC_DEBUGPL(DBG_CILV, "%s - core_if(%p)\n", __func__, core_if);
-+ if (NULL == core_if)
-+ DWC_ERROR("reg request with NULL core_if\n");
-+ DWC_DEBUGPL(DBG_CILV, "%s - core_if(%p)->dev_if(%p)\n", __func__,
-+ core_if, core_if->dev_if);
-+ if (NULL == core_if->dev_if)
-+ DWC_ERROR("reg request with NULL dev_if\n");
-+ DWC_DEBUGPL(DBG_CILV, "%s - core_if(%p)->dev_if(%p)->"
-+ "dev_global_regs(%p)\n", __func__,
-+ core_if, core_if->dev_if,
-+ core_if->dev_if->dev_global_regs);
-+ if (NULL == core_if->dev_if->dev_global_regs)
-+ DWC_ERROR("reg request with NULL dev_global_regs\n");
-+ else {
-+ DWC_DEBUGPL(DBG_CILV, "%s - &core_if(%p)->dev_if(%p)->"
-+ "dev_global_regs(%p)->dcfg = %p\n", __func__,
-+ core_if, core_if->dev_if,
-+ core_if->dev_if->dev_global_regs,
-+ &core_if->dev_if->dev_global_regs->dcfg);
-+ dcfg.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dcfg);
-+ }
-+ return dcfg.b.devspd;
-+}
-+
-+void dwc_otg_set_devspeed(dwc_otg_core_if_t * core_if, uint32_t val)
-+{
-+ dcfg_data_t dcfg;
-+ dcfg.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dcfg);
-+ dcfg.b.devspd = val;
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dcfg, dcfg.d32);
-+}
-+
-+uint32_t dwc_otg_get_busconnected(dwc_otg_core_if_t * core_if)
-+{
-+ hprt0_data_t hprt0;
-+ hprt0.d32 = DWC_READ_REG32(core_if->host_if->hprt0);
-+ return hprt0.b.prtconnsts;
-+}
-+
-+uint32_t dwc_otg_get_enumspeed(dwc_otg_core_if_t * core_if)
-+{
-+ dsts_data_t dsts;
-+ dsts.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dsts);
-+ return dsts.b.enumspd;
-+}
-+
-+uint32_t dwc_otg_get_prtpower(dwc_otg_core_if_t * core_if)
-+{
-+ hprt0_data_t hprt0;
-+ hprt0.d32 = DWC_READ_REG32(core_if->host_if->hprt0);
-+ return hprt0.b.prtpwr;
-+
-+}
-+
-+uint32_t dwc_otg_get_core_state(dwc_otg_core_if_t * core_if)
-+{
-+ return core_if->hibernation_suspend;
-+}
-+
-+void dwc_otg_set_prtpower(dwc_otg_core_if_t * core_if, uint32_t val)
-+{
-+ hprt0_data_t hprt0;
-+ hprt0.d32 = dwc_otg_read_hprt0(core_if);
-+ hprt0.b.prtpwr = val;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+}
-+
-+uint32_t dwc_otg_get_prtsuspend(dwc_otg_core_if_t * core_if)
-+{
-+ hprt0_data_t hprt0;
-+ hprt0.d32 = DWC_READ_REG32(core_if->host_if->hprt0);
-+ return hprt0.b.prtsusp;
-+
-+}
-+
-+void dwc_otg_set_prtsuspend(dwc_otg_core_if_t * core_if, uint32_t val)
-+{
-+ hprt0_data_t hprt0;
-+ hprt0.d32 = dwc_otg_read_hprt0(core_if);
-+ hprt0.b.prtsusp = val;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+}
-+
-+uint32_t dwc_otg_get_fr_interval(dwc_otg_core_if_t * core_if)
-+{
-+ hfir_data_t hfir;
-+ hfir.d32 = DWC_READ_REG32(&core_if->host_if->host_global_regs->hfir);
-+ return hfir.b.frint;
-+
-+}
-+
-+void dwc_otg_set_fr_interval(dwc_otg_core_if_t * core_if, uint32_t val)
-+{
-+ hfir_data_t hfir;
-+ uint32_t fram_int;
-+ fram_int = calc_frame_interval(core_if);
-+ hfir.d32 = DWC_READ_REG32(&core_if->host_if->host_global_regs->hfir);
-+ if (!core_if->core_params->reload_ctl) {
-+ DWC_WARN("\nCannot reload HFIR register.HFIR.HFIRRldCtrl bit is"
-+ "not set to 1.\nShould load driver with reload_ctl=1"
-+ " module parameter\n");
-+ return;
-+ }
-+ switch (fram_int) {
-+ case 3750:
-+ if ((val < 3350) || (val > 4150)) {
-+ DWC_WARN("HFIR interval for HS core and 30 MHz"
-+ "clock freq should be from 3350 to 4150\n");
-+ return;
-+ }
-+ break;
-+ case 30000:
-+ if ((val < 26820) || (val > 33180)) {
-+ DWC_WARN("HFIR interval for FS/LS core and 30 MHz"
-+ "clock freq should be from 26820 to 33180\n");
-+ return;
-+ }
-+ break;
-+ case 6000:
-+ if ((val < 5360) || (val > 6640)) {
-+ DWC_WARN("HFIR interval for HS core and 48 MHz"
-+ "clock freq should be from 5360 to 6640\n");
-+ return;
-+ }
-+ break;
-+ case 48000:
-+ if ((val < 42912) || (val > 53088)) {
-+ DWC_WARN("HFIR interval for FS/LS core and 48 MHz"
-+ "clock freq should be from 42912 to 53088\n");
-+ return;
-+ }
-+ break;
-+ case 7500:
-+ if ((val < 6700) || (val > 8300)) {
-+ DWC_WARN("HFIR interval for HS core and 60 MHz"
-+ "clock freq should be from 6700 to 8300\n");
-+ return;
-+ }
-+ break;
-+ case 60000:
-+ if ((val < 53640) || (val > 65536)) {
-+ DWC_WARN("HFIR interval for FS/LS core and 60 MHz"
-+ "clock freq should be from 53640 to 65536\n");
-+ return;
-+ }
-+ break;
-+ default:
-+ DWC_WARN("Unknown frame interval\n");
-+ return;
-+ break;
-+
-+ }
-+ hfir.b.frint = val;
-+ DWC_WRITE_REG32(&core_if->host_if->host_global_regs->hfir, hfir.d32);
-+}
-+
-+uint32_t dwc_otg_get_mode_ch_tim(dwc_otg_core_if_t * core_if)
-+{
-+ hcfg_data_t hcfg;
-+ hcfg.d32 = DWC_READ_REG32(&core_if->host_if->host_global_regs->hcfg);
-+ return hcfg.b.modechtimen;
-+
-+}
-+
-+void dwc_otg_set_mode_ch_tim(dwc_otg_core_if_t * core_if, uint32_t val)
-+{
-+ hcfg_data_t hcfg;
-+ hcfg.d32 = DWC_READ_REG32(&core_if->host_if->host_global_regs->hcfg);
-+ hcfg.b.modechtimen = val;
-+ DWC_WRITE_REG32(&core_if->host_if->host_global_regs->hcfg, hcfg.d32);
-+}
-+
-+void dwc_otg_set_prtresume(dwc_otg_core_if_t * core_if, uint32_t val)
-+{
-+ hprt0_data_t hprt0;
-+ hprt0.d32 = dwc_otg_read_hprt0(core_if);
-+ hprt0.b.prtres = val;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+}
-+
-+uint32_t dwc_otg_get_remotewakesig(dwc_otg_core_if_t * core_if)
-+{
-+ dctl_data_t dctl;
-+ dctl.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dctl);
-+ return dctl.b.rmtwkupsig;
-+}
-+
-+uint32_t dwc_otg_get_lpm_portsleepstatus(dwc_otg_core_if_t * core_if)
-+{
-+ glpmcfg_data_t lpmcfg;
-+ lpmcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg);
-+
-+ DWC_ASSERT(!
-+ ((core_if->lx_state == DWC_OTG_L1) ^ lpmcfg.b.prt_sleep_sts),
-+ "lx_state = %d, lmpcfg.prt_sleep_sts = %d\n",
-+ core_if->lx_state, lpmcfg.b.prt_sleep_sts);
-+
-+ return lpmcfg.b.prt_sleep_sts;
-+}
-+
-+uint32_t dwc_otg_get_lpm_remotewakeenabled(dwc_otg_core_if_t * core_if)
-+{
-+ glpmcfg_data_t lpmcfg;
-+ lpmcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg);
-+ return lpmcfg.b.rem_wkup_en;
-+}
-+
-+uint32_t dwc_otg_get_lpmresponse(dwc_otg_core_if_t * core_if)
-+{
-+ glpmcfg_data_t lpmcfg;
-+ lpmcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg);
-+ return lpmcfg.b.appl_resp;
-+}
-+
-+void dwc_otg_set_lpmresponse(dwc_otg_core_if_t * core_if, uint32_t val)
-+{
-+ glpmcfg_data_t lpmcfg;
-+ lpmcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg);
-+ lpmcfg.b.appl_resp = val;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->glpmcfg, lpmcfg.d32);
-+}
-+
-+uint32_t dwc_otg_get_hsic_connect(dwc_otg_core_if_t * core_if)
-+{
-+ glpmcfg_data_t lpmcfg;
-+ lpmcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg);
-+ return lpmcfg.b.hsic_connect;
-+}
-+
-+void dwc_otg_set_hsic_connect(dwc_otg_core_if_t * core_if, uint32_t val)
-+{
-+ glpmcfg_data_t lpmcfg;
-+ lpmcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg);
-+ lpmcfg.b.hsic_connect = val;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->glpmcfg, lpmcfg.d32);
-+}
-+
-+uint32_t dwc_otg_get_inv_sel_hsic(dwc_otg_core_if_t * core_if)
-+{
-+ glpmcfg_data_t lpmcfg;
-+ lpmcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg);
-+ return lpmcfg.b.inv_sel_hsic;
-+
-+}
-+
-+void dwc_otg_set_inv_sel_hsic(dwc_otg_core_if_t * core_if, uint32_t val)
-+{
-+ glpmcfg_data_t lpmcfg;
-+ lpmcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg);
-+ lpmcfg.b.inv_sel_hsic = val;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->glpmcfg, lpmcfg.d32);
-+}
-+
-+uint32_t dwc_otg_get_gotgctl(dwc_otg_core_if_t * core_if)
-+{
-+ return DWC_READ_REG32(&core_if->core_global_regs->gotgctl);
-+}
-+
-+void dwc_otg_set_gotgctl(dwc_otg_core_if_t * core_if, uint32_t val)
-+{
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gotgctl, val);
-+}
-+
-+uint32_t dwc_otg_get_gusbcfg(dwc_otg_core_if_t * core_if)
-+{
-+ return DWC_READ_REG32(&core_if->core_global_regs->gusbcfg);
-+}
-+
-+void dwc_otg_set_gusbcfg(dwc_otg_core_if_t * core_if, uint32_t val)
-+{
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gusbcfg, val);
-+}
-+
-+uint32_t dwc_otg_get_grxfsiz(dwc_otg_core_if_t * core_if)
-+{
-+ return DWC_READ_REG32(&core_if->core_global_regs->grxfsiz);
-+}
-+
-+void dwc_otg_set_grxfsiz(dwc_otg_core_if_t * core_if, uint32_t val)
-+{
-+ DWC_WRITE_REG32(&core_if->core_global_regs->grxfsiz, val);
-+}
-+
-+uint32_t dwc_otg_get_gnptxfsiz(dwc_otg_core_if_t * core_if)
-+{
-+ return DWC_READ_REG32(&core_if->core_global_regs->gnptxfsiz);
-+}
-+
-+void dwc_otg_set_gnptxfsiz(dwc_otg_core_if_t * core_if, uint32_t val)
-+{
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gnptxfsiz, val);
-+}
-+
-+uint32_t dwc_otg_get_gpvndctl(dwc_otg_core_if_t * core_if)
-+{
-+ return DWC_READ_REG32(&core_if->core_global_regs->gpvndctl);
-+}
-+
-+void dwc_otg_set_gpvndctl(dwc_otg_core_if_t * core_if, uint32_t val)
-+{
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gpvndctl, val);
-+}
-+
-+uint32_t dwc_otg_get_ggpio(dwc_otg_core_if_t * core_if)
-+{
-+ return DWC_READ_REG32(&core_if->core_global_regs->ggpio);
-+}
-+
-+void dwc_otg_set_ggpio(dwc_otg_core_if_t * core_if, uint32_t val)
-+{
-+ DWC_WRITE_REG32(&core_if->core_global_regs->ggpio, val);
-+}
-+
-+uint32_t dwc_otg_get_hprt0(dwc_otg_core_if_t * core_if)
-+{
-+ return DWC_READ_REG32(core_if->host_if->hprt0);
-+
-+}
-+
-+void dwc_otg_set_hprt0(dwc_otg_core_if_t * core_if, uint32_t val)
-+{
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, val);
-+}
-+
-+uint32_t dwc_otg_get_guid(dwc_otg_core_if_t * core_if)
-+{
-+ return DWC_READ_REG32(&core_if->core_global_regs->guid);
-+}
-+
-+void dwc_otg_set_guid(dwc_otg_core_if_t * core_if, uint32_t val)
-+{
-+ DWC_WRITE_REG32(&core_if->core_global_regs->guid, val);
-+}
-+
-+uint32_t dwc_otg_get_hptxfsiz(dwc_otg_core_if_t * core_if)
-+{
-+ return DWC_READ_REG32(&core_if->core_global_regs->hptxfsiz);
-+}
-+
-+uint16_t dwc_otg_get_otg_version(dwc_otg_core_if_t * core_if)
-+{
-+ return ((core_if->otg_ver == 1) ? (uint16_t)0x0200 : (uint16_t)0x0103);
-+}
-+
-+/**
-+ * Start the SRP timer to detect when the SRP does not complete within
-+ * 6 seconds.
-+ *
-+ * @param core_if the pointer to core_if strucure.
-+ */
-+void dwc_otg_pcd_start_srp_timer(dwc_otg_core_if_t * core_if)
-+{
-+ core_if->srp_timer_started = 1;
-+ DWC_TIMER_SCHEDULE(core_if->srp_timer, 6000 /* 6 secs */ );
-+}
-+
-+void dwc_otg_initiate_srp(dwc_otg_core_if_t * core_if)
-+{
-+ uint32_t *addr = (uint32_t *) & (core_if->core_global_regs->gotgctl);
-+ gotgctl_data_t mem;
-+ gotgctl_data_t val;
-+
-+ val.d32 = DWC_READ_REG32(addr);
-+ if (val.b.sesreq) {
-+ DWC_ERROR("Session Request Already active!\n");
-+ return;
-+ }
-+
-+ DWC_INFO("Session Request Initated\n"); //NOTICE
-+ mem.d32 = DWC_READ_REG32(addr);
-+ mem.b.sesreq = 1;
-+ DWC_WRITE_REG32(addr, mem.d32);
-+
-+ /* Start the SRP timer */
-+ dwc_otg_pcd_start_srp_timer(core_if);
-+ return;
-+}
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_cil.h
-@@ -0,0 +1,1464 @@
-+/* ==========================================================================
-+ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_cil.h $
-+ * $Revision: #123 $
-+ * $Date: 2012/08/10 $
-+ * $Change: 2047372 $
-+ *
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+
-+#if !defined(__DWC_CIL_H__)
-+#define __DWC_CIL_H__
-+
-+#include "dwc_list.h"
-+#include "dwc_otg_dbg.h"
-+#include "dwc_otg_regs.h"
-+
-+#include "dwc_otg_core_if.h"
-+#include "dwc_otg_adp.h"
-+
-+/**
-+ * @file
-+ * This file contains the interface to the Core Interface Layer.
-+ */
-+
-+#ifdef DWC_UTE_CFI
-+
-+#define MAX_DMA_DESCS_PER_EP 256
-+
-+/**
-+ * Enumeration for the data buffer mode
-+ */
-+typedef enum _data_buffer_mode {
-+ BM_STANDARD = 0, /* data buffer is in normal mode */
-+ BM_SG = 1, /* data buffer uses the scatter/gather mode */
-+ BM_CONCAT = 2, /* data buffer uses the concatenation mode */
-+ BM_CIRCULAR = 3, /* data buffer uses the circular DMA mode */
-+ BM_ALIGN = 4 /* data buffer is in buffer alignment mode */
-+} data_buffer_mode_e;
-+#endif //DWC_UTE_CFI
-+
-+/** Macros defined for DWC OTG HW Release version */
-+
-+#define OTG_CORE_REV_2_60a 0x4F54260A
-+#define OTG_CORE_REV_2_71a 0x4F54271A
-+#define OTG_CORE_REV_2_72a 0x4F54272A
-+#define OTG_CORE_REV_2_80a 0x4F54280A
-+#define OTG_CORE_REV_2_81a 0x4F54281A
-+#define OTG_CORE_REV_2_90a 0x4F54290A
-+#define OTG_CORE_REV_2_91a 0x4F54291A
-+#define OTG_CORE_REV_2_92a 0x4F54292A
-+#define OTG_CORE_REV_2_93a 0x4F54293A
-+#define OTG_CORE_REV_2_94a 0x4F54294A
-+#define OTG_CORE_REV_3_00a 0x4F54300A
-+
-+/**
-+ * Information for each ISOC packet.
-+ */
-+typedef struct iso_pkt_info {
-+ uint32_t offset;
-+ uint32_t length;
-+ int32_t status;
-+} iso_pkt_info_t;
-+
-+/**
-+ * The <code>dwc_ep</code> structure represents the state of a single
-+ * endpoint when acting in device mode. It contains the data items
-+ * needed for an endpoint to be activated and transfer packets.
-+ */
-+typedef struct dwc_ep {
-+ /** EP number used for register address lookup */
-+ uint8_t num;
-+ /** EP direction 0 = OUT */
-+ unsigned is_in:1;
-+ /** EP active. */
-+ unsigned active:1;
-+
-+ /**
-+ * Periodic Tx FIFO # for IN EPs For INTR EP set to 0 to use non-periodic
-+ * Tx FIFO. If dedicated Tx FIFOs are enabled Tx FIFO # FOR IN EPs*/
-+ unsigned tx_fifo_num:4;
-+ /** EP type: 0 - Control, 1 - ISOC, 2 - BULK, 3 - INTR */
-+ unsigned type:2;
-+#define DWC_OTG_EP_TYPE_CONTROL 0
-+#define DWC_OTG_EP_TYPE_ISOC 1
-+#define DWC_OTG_EP_TYPE_BULK 2
-+#define DWC_OTG_EP_TYPE_INTR 3
-+
-+ /** DATA start PID for INTR and BULK EP */
-+ unsigned data_pid_start:1;
-+ /** Frame (even/odd) for ISOC EP */
-+ unsigned even_odd_frame:1;
-+ /** Max Packet bytes */
-+ unsigned maxpacket:11;
-+
-+ /** Max Transfer size */
-+ uint32_t maxxfer;
-+
-+ /** @name Transfer state */
-+ /** @{ */
-+
-+ /**
-+ * Pointer to the beginning of the transfer buffer -- do not modify
-+ * during transfer.
-+ */
-+
-+ dwc_dma_t dma_addr;
-+
-+ dwc_dma_t dma_desc_addr;
-+ dwc_otg_dev_dma_desc_t *desc_addr;
-+
-+ uint8_t *start_xfer_buff;
-+ /** pointer to the transfer buffer */
-+ uint8_t *xfer_buff;
-+ /** Number of bytes to transfer */
-+ unsigned xfer_len:19;
-+ /** Number of bytes transferred. */
-+ unsigned xfer_count:19;
-+ /** Sent ZLP */
-+ unsigned sent_zlp:1;
-+ /** Total len for control transfer */
-+ unsigned total_len:19;
-+
-+ /** stall clear flag */
-+ unsigned stall_clear_flag:1;
-+
-+ /** SETUP pkt cnt rollover flag for EP0 out*/
-+ unsigned stp_rollover;
-+
-+#ifdef DWC_UTE_CFI
-+ /* The buffer mode */
-+ data_buffer_mode_e buff_mode;
-+
-+ /* The chain of DMA descriptors.
-+ * MAX_DMA_DESCS_PER_EP will be allocated for each active EP.
-+ */
-+ dwc_otg_dma_desc_t *descs;
-+
-+ /* The DMA address of the descriptors chain start */
-+ dma_addr_t descs_dma_addr;
-+ /** This variable stores the length of the last enqueued request */
-+ uint32_t cfi_req_len;
-+#endif //DWC_UTE_CFI
-+
-+/** Max DMA Descriptor count for any EP */
-+#define MAX_DMA_DESC_CNT 256
-+ /** Allocated DMA Desc count */
-+ uint32_t desc_cnt;
-+
-+ /** bInterval */
-+ uint32_t bInterval;
-+ /** Next frame num to setup next ISOC transfer */
-+ uint32_t frame_num;
-+ /** Indicates SOF number overrun in DSTS */
-+ uint8_t frm_overrun;
-+
-+#ifdef DWC_UTE_PER_IO
-+ /** Next frame num for which will be setup DMA Desc */
-+ uint32_t xiso_frame_num;
-+ /** bInterval */
-+ uint32_t xiso_bInterval;
-+ /** Count of currently active transfers - shall be either 0 or 1 */
-+ int xiso_active_xfers;
-+ int xiso_queued_xfers;
-+#endif
-+#ifdef DWC_EN_ISOC
-+ /**
-+ * Variables specific for ISOC EPs
-+ *
-+ */
-+ /** DMA addresses of ISOC buffers */
-+ dwc_dma_t dma_addr0;
-+ dwc_dma_t dma_addr1;
-+
-+ dwc_dma_t iso_dma_desc_addr;
-+ dwc_otg_dev_dma_desc_t *iso_desc_addr;
-+
-+ /** pointer to the transfer buffers */
-+ uint8_t *xfer_buff0;
-+ uint8_t *xfer_buff1;
-+
-+ /** number of ISOC Buffer is processing */
-+ uint32_t proc_buf_num;
-+ /** Interval of ISOC Buffer processing */
-+ uint32_t buf_proc_intrvl;
-+ /** Data size for regular frame */
-+ uint32_t data_per_frame;
-+
-+ /* todo - pattern data support is to be implemented in the future */
-+ /** Data size for pattern frame */
-+ uint32_t data_pattern_frame;
-+ /** Frame number of pattern data */
-+ uint32_t sync_frame;
-+
-+ /** bInterval */
-+ uint32_t bInterval;
-+ /** ISO Packet number per frame */
-+ uint32_t pkt_per_frm;
-+ /** Next frame num for which will be setup DMA Desc */
-+ uint32_t next_frame;
-+ /** Number of packets per buffer processing */
-+ uint32_t pkt_cnt;
-+ /** Info for all isoc packets */
-+ iso_pkt_info_t *pkt_info;
-+ /** current pkt number */
-+ uint32_t cur_pkt;
-+ /** current pkt number */
-+ uint8_t *cur_pkt_addr;
-+ /** current pkt number */
-+ uint32_t cur_pkt_dma_addr;
-+#endif /* DWC_EN_ISOC */
-+
-+/** @} */
-+} dwc_ep_t;
-+
-+/*
-+ * Reasons for halting a host channel.
-+ */
-+typedef enum dwc_otg_halt_status {
-+ DWC_OTG_HC_XFER_NO_HALT_STATUS,
-+ DWC_OTG_HC_XFER_COMPLETE,
-+ DWC_OTG_HC_XFER_URB_COMPLETE,
-+ DWC_OTG_HC_XFER_ACK,
-+ DWC_OTG_HC_XFER_NAK,
-+ DWC_OTG_HC_XFER_NYET,
-+ DWC_OTG_HC_XFER_STALL,
-+ DWC_OTG_HC_XFER_XACT_ERR,
-+ DWC_OTG_HC_XFER_FRAME_OVERRUN,
-+ DWC_OTG_HC_XFER_BABBLE_ERR,
-+ DWC_OTG_HC_XFER_DATA_TOGGLE_ERR,
-+ DWC_OTG_HC_XFER_AHB_ERR,
-+ DWC_OTG_HC_XFER_PERIODIC_INCOMPLETE,
-+ DWC_OTG_HC_XFER_URB_DEQUEUE
-+} dwc_otg_halt_status_e;
-+
-+/**
-+ * Host channel descriptor. This structure represents the state of a single
-+ * host channel when acting in host mode. It contains the data items needed to
-+ * transfer packets to an endpoint via a host channel.
-+ */
-+typedef struct dwc_hc {
-+ /** Host channel number used for register address lookup */
-+ uint8_t hc_num;
-+
-+ /** Device to access */
-+ unsigned dev_addr:7;
-+
-+ /** EP to access */
-+ unsigned ep_num:4;
-+
-+ /** EP direction. 0: OUT, 1: IN */
-+ unsigned ep_is_in:1;
-+
-+ /**
-+ * EP speed.
-+ * One of the following values:
-+ * - DWC_OTG_EP_SPEED_LOW
-+ * - DWC_OTG_EP_SPEED_FULL
-+ * - DWC_OTG_EP_SPEED_HIGH
-+ */
-+ unsigned speed:2;
-+#define DWC_OTG_EP_SPEED_LOW 0
-+#define DWC_OTG_EP_SPEED_FULL 1
-+#define DWC_OTG_EP_SPEED_HIGH 2
-+
-+ /**
-+ * Endpoint type.
-+ * One of the following values:
-+ * - DWC_OTG_EP_TYPE_CONTROL: 0
-+ * - DWC_OTG_EP_TYPE_ISOC: 1
-+ * - DWC_OTG_EP_TYPE_BULK: 2
-+ * - DWC_OTG_EP_TYPE_INTR: 3
-+ */
-+ unsigned ep_type:2;
-+
-+ /** Max packet size in bytes */
-+ unsigned max_packet:11;
-+
-+ /**
-+ * PID for initial transaction.
-+ * 0: DATA0,<br>
-+ * 1: DATA2,<br>
-+ * 2: DATA1,<br>
-+ * 3: MDATA (non-Control EP),
-+ * SETUP (Control EP)
-+ */
-+ unsigned data_pid_start:2;
-+#define DWC_OTG_HC_PID_DATA0 0
-+#define DWC_OTG_HC_PID_DATA2 1
-+#define DWC_OTG_HC_PID_DATA1 2
-+#define DWC_OTG_HC_PID_MDATA 3
-+#define DWC_OTG_HC_PID_SETUP 3
-+
-+ /** Number of periodic transactions per (micro)frame */
-+ unsigned multi_count:2;
-+
-+ /** @name Transfer State */
-+ /** @{ */
-+
-+ /** Pointer to the current transfer buffer position. */
-+ uint8_t *xfer_buff;
-+ /**
-+ * In Buffer DMA mode this buffer will be used
-+ * if xfer_buff is not DWORD aligned.
-+ */
-+ dwc_dma_t align_buff;
-+ /** Total number of bytes to transfer. */
-+ uint32_t xfer_len;
-+ /** Number of bytes transferred so far. */
-+ uint32_t xfer_count;
-+ /** Packet count at start of transfer.*/
-+ uint16_t start_pkt_count;
-+
-+ /**
-+ * Flag to indicate whether the transfer has been started. Set to 1 if
-+ * it has been started, 0 otherwise.
-+ */
-+ uint8_t xfer_started;
-+
-+ /**
-+ * Set to 1 to indicate that a PING request should be issued on this
-+ * channel. If 0, process normally.
-+ */
-+ uint8_t do_ping;
-+
-+ /**
-+ * Set to 1 to indicate that the error count for this transaction is
-+ * non-zero. Set to 0 if the error count is 0.
-+ */
-+ uint8_t error_state;
-+
-+ /**
-+ * Set to 1 to indicate that this channel should be halted the next
-+ * time a request is queued for the channel. This is necessary in
-+ * slave mode if no request queue space is available when an attempt
-+ * is made to halt the channel.
-+ */
-+ uint8_t halt_on_queue;
-+
-+ /**
-+ * Set to 1 if the host channel has been halted, but the core is not
-+ * finished flushing queued requests. Otherwise 0.
-+ */
-+ uint8_t halt_pending;
-+
-+ /**
-+ * Reason for halting the host channel.
-+ */
-+ dwc_otg_halt_status_e halt_status;
-+
-+ /*
-+ * Split settings for the host channel
-+ */
-+ uint8_t do_split; /**< Enable split for the channel */
-+ uint8_t complete_split; /**< Enable complete split */
-+ uint8_t hub_addr; /**< Address of high speed hub */
-+
-+ uint8_t port_addr; /**< Port of the low/full speed device */
-+ /** Split transaction position
-+ * One of the following values:
-+ * - DWC_HCSPLIT_XACTPOS_MID
-+ * - DWC_HCSPLIT_XACTPOS_BEGIN
-+ * - DWC_HCSPLIT_XACTPOS_END
-+ * - DWC_HCSPLIT_XACTPOS_ALL */
-+ uint8_t xact_pos;
-+
-+ /** Set when the host channel does a short read. */
-+ uint8_t short_read;
-+
-+ /**
-+ * Number of requests issued for this channel since it was assigned to
-+ * the current transfer (not counting PINGs).
-+ */
-+ uint8_t requests;
-+
-+ /**
-+ * Queue Head for the transfer being processed by this channel.
-+ */
-+ struct dwc_otg_qh *qh;
-+
-+ /** @} */
-+
-+ /** Entry in list of host channels. */
-+ DWC_CIRCLEQ_ENTRY(dwc_hc) hc_list_entry;
-+
-+ /** @name Descriptor DMA support */
-+ /** @{ */
-+
-+ /** Number of Transfer Descriptors */
-+ uint16_t ntd;
-+
-+ /** Descriptor List DMA address */
-+ dwc_dma_t desc_list_addr;
-+
-+ /** Scheduling micro-frame bitmap. */
-+ uint8_t schinfo;
-+
-+ /** @} */
-+} dwc_hc_t;
-+
-+/**
-+ * The following parameters may be specified when starting the module. These
-+ * parameters define how the DWC_otg controller should be configured.
-+ */
-+typedef struct dwc_otg_core_params {
-+ int32_t opt;
-+
-+ /**
-+ * Specifies the OTG capabilities. The driver will automatically
-+ * detect the value for this parameter if none is specified.
-+ * 0 - HNP and SRP capable (default)
-+ * 1 - SRP Only capable
-+ * 2 - No HNP/SRP capable
-+ */
-+ int32_t otg_cap;
-+
-+ /**
-+ * Specifies whether to use slave or DMA mode for accessing the data
-+ * FIFOs. The driver will automatically detect the value for this
-+ * parameter if none is specified.
-+ * 0 - Slave
-+ * 1 - DMA (default, if available)
-+ */
-+ int32_t dma_enable;
-+
-+ /**
-+ * When DMA mode is enabled specifies whether to use address DMA or DMA
-+ * Descriptor mode for accessing the data FIFOs in device mode. The driver
-+ * will automatically detect the value for this if none is specified.
-+ * 0 - address DMA
-+ * 1 - DMA Descriptor(default, if available)
-+ */
-+ int32_t dma_desc_enable;
-+ /** The DMA Burst size (applicable only for External DMA
-+ * Mode). 1, 4, 8 16, 32, 64, 128, 256 (default 32)
-+ */
-+ int32_t dma_burst_size; /* Translate this to GAHBCFG values */
-+
-+ /**
-+ * Specifies the maximum speed of operation in host and device mode.
-+ * The actual speed depends on the speed of the attached device and
-+ * the value of phy_type. The actual speed depends on the speed of the
-+ * attached device.
-+ * 0 - High Speed (default)
-+ * 1 - Full Speed
-+ */
-+ int32_t speed;
-+ /** Specifies whether low power mode is supported when attached
-+ * to a Full Speed or Low Speed device in host mode.
-+ * 0 - Don't support low power mode (default)
-+ * 1 - Support low power mode
-+ */
-+ int32_t host_support_fs_ls_low_power;
-+
-+ /** Specifies the PHY clock rate in low power mode when connected to a
-+ * Low Speed device in host mode. This parameter is applicable only if
-+ * HOST_SUPPORT_FS_LS_LOW_POWER is enabled. If PHY_TYPE is set to FS
-+ * then defaults to 6 MHZ otherwise 48 MHZ.
-+ *
-+ * 0 - 48 MHz
-+ * 1 - 6 MHz
-+ */
-+ int32_t host_ls_low_power_phy_clk;
-+
-+ /**
-+ * 0 - Use cC FIFO size parameters
-+ * 1 - Allow dynamic FIFO sizing (default)
-+ */
-+ int32_t enable_dynamic_fifo;
-+
-+ /** Total number of 4-byte words in the data FIFO memory. This
-+ * memory includes the Rx FIFO, non-periodic Tx FIFO, and periodic
-+ * Tx FIFOs.
-+ * 32 to 32768 (default 8192)
-+ * Note: The total FIFO memory depth in the FPGA configuration is 8192.
-+ */
-+ int32_t data_fifo_size;
-+
-+ /** Number of 4-byte words in the Rx FIFO in device mode when dynamic
-+ * FIFO sizing is enabled.
-+ * 16 to 32768 (default 1064)
-+ */
-+ int32_t dev_rx_fifo_size;
-+
-+ /** Number of 4-byte words in the non-periodic Tx FIFO in device mode
-+ * when dynamic FIFO sizing is enabled.
-+ * 16 to 32768 (default 1024)
-+ */
-+ int32_t dev_nperio_tx_fifo_size;
-+
-+ /** Number of 4-byte words in each of the periodic Tx FIFOs in device
-+ * mode when dynamic FIFO sizing is enabled.
-+ * 4 to 768 (default 256)
-+ */
-+ uint32_t dev_perio_tx_fifo_size[MAX_PERIO_FIFOS];
-+
-+ /** Number of 4-byte words in the Rx FIFO in host mode when dynamic
-+ * FIFO sizing is enabled.
-+ * 16 to 32768 (default 1024)
-+ */
-+ int32_t host_rx_fifo_size;
-+
-+ /** Number of 4-byte words in the non-periodic Tx FIFO in host mode
-+ * when Dynamic FIFO sizing is enabled in the core.
-+ * 16 to 32768 (default 1024)
-+ */
-+ int32_t host_nperio_tx_fifo_size;
-+
-+ /** Number of 4-byte words in the host periodic Tx FIFO when dynamic
-+ * FIFO sizing is enabled.
-+ * 16 to 32768 (default 1024)
-+ */
-+ int32_t host_perio_tx_fifo_size;
-+
-+ /** The maximum transfer size supported in bytes.
-+ * 2047 to 65,535 (default 65,535)
-+ */
-+ int32_t max_transfer_size;
-+
-+ /** The maximum number of packets in a transfer.
-+ * 15 to 511 (default 511)
-+ */
-+ int32_t max_packet_count;
-+
-+ /** The number of host channel registers to use.
-+ * 1 to 16 (default 12)
-+ * Note: The FPGA configuration supports a maximum of 12 host channels.
-+ */
-+ int32_t host_channels;
-+
-+ /** The number of endpoints in addition to EP0 available for device
-+ * mode operations.
-+ * 1 to 15 (default 6 IN and OUT)
-+ * Note: The FPGA configuration supports a maximum of 6 IN and OUT
-+ * endpoints in addition to EP0.
-+ */
-+ int32_t dev_endpoints;
-+
-+ /**
-+ * Specifies the type of PHY interface to use. By default, the driver
-+ * will automatically detect the phy_type.
-+ *
-+ * 0 - Full Speed PHY
-+ * 1 - UTMI+ (default)
-+ * 2 - ULPI
-+ */
-+ int32_t phy_type;
-+
-+ /**
-+ * Specifies the UTMI+ Data Width. This parameter is
-+ * applicable for a PHY_TYPE of UTMI+ or ULPI. (For a ULPI
-+ * PHY_TYPE, this parameter indicates the data width between
-+ * the MAC and the ULPI Wrapper.) Also, this parameter is
-+ * applicable only if the OTG_HSPHY_WIDTH cC parameter was set
-+ * to "8 and 16 bits", meaning that the core has been
-+ * configured to work at either data path width.
-+ *
-+ * 8 or 16 bits (default 16)
-+ */
-+ int32_t phy_utmi_width;
-+
-+ /**
-+ * Specifies whether the ULPI operates at double or single
-+ * data rate. This parameter is only applicable if PHY_TYPE is
-+ * ULPI.
-+ *
-+ * 0 - single data rate ULPI interface with 8 bit wide data
-+ * bus (default)
-+ * 1 - double data rate ULPI interface with 4 bit wide data
-+ * bus
-+ */
-+ int32_t phy_ulpi_ddr;
-+
-+ /**
-+ * Specifies whether to use the internal or external supply to
-+ * drive the vbus with a ULPI phy.
-+ */
-+ int32_t phy_ulpi_ext_vbus;
-+
-+ /**
-+ * Specifies whether to use the I2Cinterface for full speed PHY. This
-+ * parameter is only applicable if PHY_TYPE is FS.
-+ * 0 - No (default)
-+ * 1 - Yes
-+ */
-+ int32_t i2c_enable;
-+
-+ int32_t ulpi_fs_ls;
-+
-+ int32_t ts_dline;
-+
-+ /**
-+ * Specifies whether dedicated transmit FIFOs are
-+ * enabled for non periodic IN endpoints in device mode
-+ * 0 - No
-+ * 1 - Yes
-+ */
-+ int32_t en_multiple_tx_fifo;
-+
-+ /** Number of 4-byte words in each of the Tx FIFOs in device
-+ * mode when dynamic FIFO sizing is enabled.
-+ * 4 to 768 (default 256)
-+ */
-+ uint32_t dev_tx_fifo_size[MAX_TX_FIFOS];
-+
-+ /** Thresholding enable flag-
-+ * bit 0 - enable non-ISO Tx thresholding
-+ * bit 1 - enable ISO Tx thresholding
-+ * bit 2 - enable Rx thresholding
-+ */
-+ uint32_t thr_ctl;
-+
-+ /** Thresholding length for Tx
-+ * FIFOs in 32 bit DWORDs
-+ */
-+ uint32_t tx_thr_length;
-+
-+ /** Thresholding length for Rx
-+ * FIFOs in 32 bit DWORDs
-+ */
-+ uint32_t rx_thr_length;
-+
-+ /**
-+ * Specifies whether LPM (Link Power Management) support is enabled
-+ */
-+ int32_t lpm_enable;
-+
-+ /** Per Transfer Interrupt
-+ * mode enable flag
-+ * 1 - Enabled
-+ * 0 - Disabled
-+ */
-+ int32_t pti_enable;
-+
-+ /** Multi Processor Interrupt
-+ * mode enable flag
-+ * 1 - Enabled
-+ * 0 - Disabled
-+ */
-+ int32_t mpi_enable;
-+
-+ /** IS_USB Capability
-+ * 1 - Enabled
-+ * 0 - Disabled
-+ */
-+ int32_t ic_usb_cap;
-+
-+ /** AHB Threshold Ratio
-+ * 2'b00 AHB Threshold = MAC Threshold
-+ * 2'b01 AHB Threshold = 1/2 MAC Threshold
-+ * 2'b10 AHB Threshold = 1/4 MAC Threshold
-+ * 2'b11 AHB Threshold = 1/8 MAC Threshold
-+ */
-+ int32_t ahb_thr_ratio;
-+
-+ /** ADP Support
-+ * 1 - Enabled
-+ * 0 - Disabled
-+ */
-+ int32_t adp_supp_enable;
-+
-+ /** HFIR Reload Control
-+ * 0 - The HFIR cannot be reloaded dynamically.
-+ * 1 - Allow dynamic reloading of the HFIR register during runtime.
-+ */
-+ int32_t reload_ctl;
-+
-+ /** DCFG: Enable device Out NAK
-+ * 0 - The core does not set NAK after Bulk Out transfer complete.
-+ * 1 - The core sets NAK after Bulk OUT transfer complete.
-+ */
-+ int32_t dev_out_nak;
-+
-+ /** DCFG: Enable Continue on BNA
-+ * After receiving BNA interrupt the core disables the endpoint,when the
-+ * endpoint is re-enabled by the application the core starts processing
-+ * 0 - from the DOEPDMA descriptor
-+ * 1 - from the descriptor which received the BNA.
-+ */
-+ int32_t cont_on_bna;
-+
-+ /** GAHBCFG: AHB Single Support
-+ * This bit when programmed supports SINGLE transfers for remainder
-+ * data in a transfer for DMA mode of operation.
-+ * 0 - in this case the remainder data will be sent using INCR burst size.
-+ * 1 - in this case the remainder data will be sent using SINGLE burst size.
-+ */
-+ int32_t ahb_single;
-+
-+ /** Core Power down mode
-+ * 0 - No Power Down is enabled
-+ * 1 - Reserved
-+ * 2 - Complete Power Down (Hibernation)
-+ */
-+ int32_t power_down;
-+
-+ /** OTG revision supported
-+ * 0 - OTG 1.3 revision
-+ * 1 - OTG 2.0 revision
-+ */
-+ int32_t otg_ver;
-+
-+} dwc_otg_core_params_t;
-+
-+#ifdef DEBUG
-+struct dwc_otg_core_if;
-+typedef struct hc_xfer_info {
-+ struct dwc_otg_core_if *core_if;
-+ dwc_hc_t *hc;
-+} hc_xfer_info_t;
-+#endif
-+
-+typedef struct ep_xfer_info {
-+ struct dwc_otg_core_if *core_if;
-+ dwc_ep_t *ep;
-+ uint8_t state;
-+} ep_xfer_info_t;
-+/*
-+ * Device States
-+ */
-+typedef enum dwc_otg_lx_state {
-+ /** On state */
-+ DWC_OTG_L0,
-+ /** LPM sleep state*/
-+ DWC_OTG_L1,
-+ /** USB suspend state*/
-+ DWC_OTG_L2,
-+ /** Off state*/
-+ DWC_OTG_L3
-+} dwc_otg_lx_state_e;
-+
-+struct dwc_otg_global_regs_backup {
-+ uint32_t gotgctl_local;
-+ uint32_t gintmsk_local;
-+ uint32_t gahbcfg_local;
-+ uint32_t gusbcfg_local;
-+ uint32_t grxfsiz_local;
-+ uint32_t gnptxfsiz_local;
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+ uint32_t glpmcfg_local;
-+#endif
-+ uint32_t gi2cctl_local;
-+ uint32_t hptxfsiz_local;
-+ uint32_t pcgcctl_local;
-+ uint32_t gdfifocfg_local;
-+ uint32_t dtxfsiz_local[MAX_EPS_CHANNELS];
-+ uint32_t gpwrdn_local;
-+ uint32_t xhib_pcgcctl;
-+ uint32_t xhib_gpwrdn;
-+};
-+
-+struct dwc_otg_host_regs_backup {
-+ uint32_t hcfg_local;
-+ uint32_t haintmsk_local;
-+ uint32_t hcintmsk_local[MAX_EPS_CHANNELS];
-+ uint32_t hprt0_local;
-+ uint32_t hfir_local;
-+};
-+
-+struct dwc_otg_dev_regs_backup {
-+ uint32_t dcfg;
-+ uint32_t dctl;
-+ uint32_t daintmsk;
-+ uint32_t diepmsk;
-+ uint32_t doepmsk;
-+ uint32_t diepctl[MAX_EPS_CHANNELS];
-+ uint32_t dieptsiz[MAX_EPS_CHANNELS];
-+ uint32_t diepdma[MAX_EPS_CHANNELS];
-+};
-+/**
-+ * The <code>dwc_otg_core_if</code> structure contains information needed to manage
-+ * the DWC_otg controller acting in either host or device mode. It
-+ * represents the programming view of the controller as a whole.
-+ */
-+struct dwc_otg_core_if {
-+ /** Parameters that define how the core should be configured.*/
-+ dwc_otg_core_params_t *core_params;
-+
-+ /** Core Global registers starting at offset 000h. */
-+ dwc_otg_core_global_regs_t *core_global_regs;
-+
-+ /** Device-specific information */
-+ dwc_otg_dev_if_t *dev_if;
-+ /** Host-specific information */
-+ dwc_otg_host_if_t *host_if;
-+
-+ /** Value from SNPSID register */
-+ uint32_t snpsid;
-+
-+ /*
-+ * Set to 1 if the core PHY interface bits in USBCFG have been
-+ * initialized.
-+ */
-+ uint8_t phy_init_done;
-+
-+ /*
-+ * SRP Success flag, set by srp success interrupt in FS I2C mode
-+ */
-+ uint8_t srp_success;
-+ uint8_t srp_timer_started;
-+ /** Timer for SRP. If it expires before SRP is successful
-+ * clear the SRP. */
-+ dwc_timer_t *srp_timer;
-+
-+#ifdef DWC_DEV_SRPCAP
-+ /* This timer is needed to power on the hibernated host core if SRP is not
-+ * initiated on connected SRP capable device for limited period of time
-+ */
-+ uint8_t pwron_timer_started;
-+ dwc_timer_t *pwron_timer;
-+#endif
-+ /* Common configuration information */
-+ /** Power and Clock Gating Control Register */
-+ volatile uint32_t *pcgcctl;
-+#define DWC_OTG_PCGCCTL_OFFSET 0xE00
-+
-+ /** Push/pop addresses for endpoints or host channels.*/
-+ uint32_t *data_fifo[MAX_EPS_CHANNELS];
-+#define DWC_OTG_DATA_FIFO_OFFSET 0x1000
-+#define DWC_OTG_DATA_FIFO_SIZE 0x1000
-+
-+ /** Total RAM for FIFOs (Bytes) */
-+ uint16_t total_fifo_size;
-+ /** Size of Rx FIFO (Bytes) */
-+ uint16_t rx_fifo_size;
-+ /** Size of Non-periodic Tx FIFO (Bytes) */
-+ uint16_t nperio_tx_fifo_size;
-+
-+ /** 1 if DMA is enabled, 0 otherwise. */
-+ uint8_t dma_enable;
-+
-+ /** 1 if DMA descriptor is enabled, 0 otherwise. */
-+ uint8_t dma_desc_enable;
-+
-+ /** 1 if PTI Enhancement mode is enabled, 0 otherwise. */
-+ uint8_t pti_enh_enable;
-+
-+ /** 1 if MPI Enhancement mode is enabled, 0 otherwise. */
-+ uint8_t multiproc_int_enable;
-+
-+ /** 1 if dedicated Tx FIFOs are enabled, 0 otherwise. */
-+ uint8_t en_multiple_tx_fifo;
-+
-+ /** Set to 1 if multiple packets of a high-bandwidth transfer is in
-+ * process of being queued */
-+ uint8_t queuing_high_bandwidth;
-+
-+ /** Hardware Configuration -- stored here for convenience.*/
-+ hwcfg1_data_t hwcfg1;
-+ hwcfg2_data_t hwcfg2;
-+ hwcfg3_data_t hwcfg3;
-+ hwcfg4_data_t hwcfg4;
-+ fifosize_data_t hptxfsiz;
-+
-+ /** Host and Device Configuration -- stored here for convenience.*/
-+ hcfg_data_t hcfg;
-+ dcfg_data_t dcfg;
-+
-+ /** The operational State, during transations
-+ * (a_host>>a_peripherial and b_device=>b_host) this may not
-+ * match the core but allows the software to determine
-+ * transitions.
-+ */
-+ uint8_t op_state;
-+
-+ /**
-+ * Set to 1 if the HCD needs to be restarted on a session request
-+ * interrupt. This is required if no connector ID status change has
-+ * occurred since the HCD was last disconnected.
-+ */
-+ uint8_t restart_hcd_on_session_req;
-+
-+ /** HCD callbacks */
-+ /** A-Device is a_host */
-+#define A_HOST (1)
-+ /** A-Device is a_suspend */
-+#define A_SUSPEND (2)
-+ /** A-Device is a_peripherial */
-+#define A_PERIPHERAL (3)
-+ /** B-Device is operating as a Peripheral. */
-+#define B_PERIPHERAL (4)
-+ /** B-Device is operating as a Host. */
-+#define B_HOST (5)
-+
-+ /** HCD callbacks */
-+ struct dwc_otg_cil_callbacks *hcd_cb;
-+ /** PCD callbacks */
-+ struct dwc_otg_cil_callbacks *pcd_cb;
-+
-+ /** Device mode Periodic Tx FIFO Mask */
-+ uint32_t p_tx_msk;
-+ /** Device mode Periodic Tx FIFO Mask */
-+ uint32_t tx_msk;
-+
-+ /** Workqueue object used for handling several interrupts */
-+ dwc_workq_t *wq_otg;
-+
-+ /** Timer object used for handling "Wakeup Detected" Interrupt */
-+ dwc_timer_t *wkp_timer;
-+ /** This arrays used for debug purposes for DEV OUT NAK enhancement */
-+ uint32_t start_doeptsiz_val[MAX_EPS_CHANNELS];
-+ ep_xfer_info_t ep_xfer_info[MAX_EPS_CHANNELS];
-+ dwc_timer_t *ep_xfer_timer[MAX_EPS_CHANNELS];
-+#ifdef DEBUG
-+ uint32_t start_hcchar_val[MAX_EPS_CHANNELS];
-+
-+ hc_xfer_info_t hc_xfer_info[MAX_EPS_CHANNELS];
-+ dwc_timer_t *hc_xfer_timer[MAX_EPS_CHANNELS];
-+
-+ uint32_t hfnum_7_samples;
-+ uint64_t hfnum_7_frrem_accum;
-+ uint32_t hfnum_0_samples;
-+ uint64_t hfnum_0_frrem_accum;
-+ uint32_t hfnum_other_samples;
-+ uint64_t hfnum_other_frrem_accum;
-+#endif
-+
-+#ifdef DWC_UTE_CFI
-+ uint16_t pwron_rxfsiz;
-+ uint16_t pwron_gnptxfsiz;
-+ uint16_t pwron_txfsiz[15];
-+
-+ uint16_t init_rxfsiz;
-+ uint16_t init_gnptxfsiz;
-+ uint16_t init_txfsiz[15];
-+#endif
-+
-+ /** Lx state of device */
-+ dwc_otg_lx_state_e lx_state;
-+
-+ /** Saved Core Global registers */
-+ struct dwc_otg_global_regs_backup *gr_backup;
-+ /** Saved Host registers */
-+ struct dwc_otg_host_regs_backup *hr_backup;
-+ /** Saved Device registers */
-+ struct dwc_otg_dev_regs_backup *dr_backup;
-+
-+ /** Power Down Enable */
-+ uint32_t power_down;
-+
-+ /** ADP support Enable */
-+ uint32_t adp_enable;
-+
-+ /** ADP structure object */
-+ dwc_otg_adp_t adp;
-+
-+ /** hibernation/suspend flag */
-+ int hibernation_suspend;
-+
-+ /** Device mode extended hibernation flag */
-+ int xhib;
-+
-+ /** OTG revision supported */
-+ uint32_t otg_ver;
-+
-+ /** OTG status flag used for HNP polling */
-+ uint8_t otg_sts;
-+
-+ /** Pointer to either hcd->lock or pcd->lock */
-+ dwc_spinlock_t *lock;
-+
-+ /** Start predict NextEP based on Learning Queue if equal 1,
-+ * also used as counter of disabled NP IN EP's */
-+ uint8_t start_predict;
-+
-+ /** NextEp sequence, including EP0: nextep_seq[] = EP if non-periodic and
-+ * active, 0xff otherwise */
-+ uint8_t nextep_seq[MAX_EPS_CHANNELS];
-+
-+ /** Index of fisrt EP in nextep_seq array which should be re-enabled **/
-+ uint8_t first_in_nextep_seq;
-+
-+ /** Frame number while entering to ISR - needed for ISOCs **/
-+ uint32_t frame_num;
-+
-+};
-+
-+#ifdef DEBUG
-+/*
-+ * This function is called when transfer is timed out.
-+ */
-+extern void hc_xfer_timeout(void *ptr);
-+#endif
-+
-+/*
-+ * This function is called when transfer is timed out on endpoint.
-+ */
-+extern void ep_xfer_timeout(void *ptr);
-+
-+/*
-+ * The following functions are functions for works
-+ * using during handling some interrupts
-+ */
-+extern void w_conn_id_status_change(void *p);
-+
-+extern void w_wakeup_detected(void *p);
-+
-+/** Saves global register values into system memory. */
-+extern int dwc_otg_save_global_regs(dwc_otg_core_if_t * core_if);
-+/** Saves device register values into system memory. */
-+extern int dwc_otg_save_dev_regs(dwc_otg_core_if_t * core_if);
-+/** Saves host register values into system memory. */
-+extern int dwc_otg_save_host_regs(dwc_otg_core_if_t * core_if);
-+/** Restore global register values. */
-+extern int dwc_otg_restore_global_regs(dwc_otg_core_if_t * core_if);
-+/** Restore host register values. */
-+extern int dwc_otg_restore_host_regs(dwc_otg_core_if_t * core_if, int reset);
-+/** Restore device register values. */
-+extern int dwc_otg_restore_dev_regs(dwc_otg_core_if_t * core_if,
-+ int rem_wakeup);
-+extern int restore_lpm_i2c_regs(dwc_otg_core_if_t * core_if);
-+extern int restore_essential_regs(dwc_otg_core_if_t * core_if, int rmode,
-+ int is_host);
-+
-+extern int dwc_otg_host_hibernation_restore(dwc_otg_core_if_t * core_if,
-+ int restore_mode, int reset);
-+extern int dwc_otg_device_hibernation_restore(dwc_otg_core_if_t * core_if,
-+ int rem_wakeup, int reset);
-+
-+/*
-+ * The following functions support initialization of the CIL driver component
-+ * and the DWC_otg controller.
-+ */
-+extern void dwc_otg_core_host_init(dwc_otg_core_if_t * _core_if);
-+extern void dwc_otg_core_dev_init(dwc_otg_core_if_t * _core_if);
-+
-+/** @name Device CIL Functions
-+ * The following functions support managing the DWC_otg controller in device
-+ * mode.
-+ */
-+/**@{*/
-+extern void dwc_otg_wakeup(dwc_otg_core_if_t * _core_if);
-+extern void dwc_otg_read_setup_packet(dwc_otg_core_if_t * _core_if,
-+ uint32_t * _dest);
-+extern uint32_t dwc_otg_get_frame_number(dwc_otg_core_if_t * _core_if);
-+extern void dwc_otg_ep0_activate(dwc_otg_core_if_t * _core_if, dwc_ep_t * _ep);
-+extern void dwc_otg_ep_activate(dwc_otg_core_if_t * _core_if, dwc_ep_t * _ep);
-+extern void dwc_otg_ep_deactivate(dwc_otg_core_if_t * _core_if, dwc_ep_t * _ep);
-+extern void dwc_otg_ep_start_transfer(dwc_otg_core_if_t * _core_if,
-+ dwc_ep_t * _ep);
-+extern void dwc_otg_ep_start_zl_transfer(dwc_otg_core_if_t * _core_if,
-+ dwc_ep_t * _ep);
-+extern void dwc_otg_ep0_start_transfer(dwc_otg_core_if_t * _core_if,
-+ dwc_ep_t * _ep);
-+extern void dwc_otg_ep0_continue_transfer(dwc_otg_core_if_t * _core_if,
-+ dwc_ep_t * _ep);
-+extern void dwc_otg_ep_write_packet(dwc_otg_core_if_t * _core_if,
-+ dwc_ep_t * _ep, int _dma);
-+extern void dwc_otg_ep_set_stall(dwc_otg_core_if_t * _core_if, dwc_ep_t * _ep);
-+extern void dwc_otg_ep_clear_stall(dwc_otg_core_if_t * _core_if,
-+ dwc_ep_t * _ep);
-+extern void dwc_otg_enable_device_interrupts(dwc_otg_core_if_t * _core_if);
-+
-+#ifdef DWC_EN_ISOC
-+extern void dwc_otg_iso_ep_start_frm_transfer(dwc_otg_core_if_t * core_if,
-+ dwc_ep_t * ep);
-+extern void dwc_otg_iso_ep_start_buf_transfer(dwc_otg_core_if_t * core_if,
-+ dwc_ep_t * ep);
-+#endif /* DWC_EN_ISOC */
-+/**@}*/
-+
-+/** @name Host CIL Functions
-+ * The following functions support managing the DWC_otg controller in host
-+ * mode.
-+ */
-+/**@{*/
-+extern void dwc_otg_hc_init(dwc_otg_core_if_t * _core_if, dwc_hc_t * _hc);
-+extern void dwc_otg_hc_halt(dwc_otg_core_if_t * _core_if,
-+ dwc_hc_t * _hc, dwc_otg_halt_status_e _halt_status);
-+extern void dwc_otg_hc_cleanup(dwc_otg_core_if_t * _core_if, dwc_hc_t * _hc);
-+extern void dwc_otg_hc_start_transfer(dwc_otg_core_if_t * _core_if,
-+ dwc_hc_t * _hc);
-+extern int dwc_otg_hc_continue_transfer(dwc_otg_core_if_t * _core_if,
-+ dwc_hc_t * _hc);
-+extern void dwc_otg_hc_do_ping(dwc_otg_core_if_t * _core_if, dwc_hc_t * _hc);
-+extern void dwc_otg_hc_write_packet(dwc_otg_core_if_t * _core_if,
-+ dwc_hc_t * _hc);
-+extern void dwc_otg_enable_host_interrupts(dwc_otg_core_if_t * _core_if);
-+extern void dwc_otg_disable_host_interrupts(dwc_otg_core_if_t * _core_if);
-+
-+extern void dwc_otg_hc_start_transfer_ddma(dwc_otg_core_if_t * core_if,
-+ dwc_hc_t * hc);
-+
-+extern uint32_t calc_frame_interval(dwc_otg_core_if_t * core_if);
-+
-+/* Macro used to clear one channel interrupt */
-+#define clear_hc_int(_hc_regs_, _intr_) \
-+do { \
-+ hcint_data_t hcint_clear = {.d32 = 0}; \
-+ hcint_clear.b._intr_ = 1; \
-+ DWC_WRITE_REG32(&(_hc_regs_)->hcint, hcint_clear.d32); \
-+} while (0)
-+
-+/*
-+ * Macro used to disable one channel interrupt. Channel interrupts are
-+ * disabled when the channel is halted or released by the interrupt handler.
-+ * There is no need to handle further interrupts of that type until the
-+ * channel is re-assigned. In fact, subsequent handling may cause crashes
-+ * because the channel structures are cleaned up when the channel is released.
-+ */
-+#define disable_hc_int(_hc_regs_, _intr_) \
-+do { \
-+ hcintmsk_data_t hcintmsk = {.d32 = 0}; \
-+ hcintmsk.b._intr_ = 1; \
-+ DWC_MODIFY_REG32(&(_hc_regs_)->hcintmsk, hcintmsk.d32, 0); \
-+} while (0)
-+
-+/**
-+ * This function Reads HPRT0 in preparation to modify. It keeps the
-+ * WC bits 0 so that if they are read as 1, they won't clear when you
-+ * write it back
-+ */
-+static inline uint32_t dwc_otg_read_hprt0(dwc_otg_core_if_t * _core_if)
-+{
-+ hprt0_data_t hprt0;
-+ hprt0.d32 = DWC_READ_REG32(_core_if->host_if->hprt0);
-+ hprt0.b.prtena = 0;
-+ hprt0.b.prtconndet = 0;
-+ hprt0.b.prtenchng = 0;
-+ hprt0.b.prtovrcurrchng = 0;
-+ return hprt0.d32;
-+}
-+
-+/**@}*/
-+
-+/** @name Common CIL Functions
-+ * The following functions support managing the DWC_otg controller in either
-+ * device or host mode.
-+ */
-+/**@{*/
-+
-+extern void dwc_otg_read_packet(dwc_otg_core_if_t * core_if,
-+ uint8_t * dest, uint16_t bytes);
-+
-+extern void dwc_otg_flush_tx_fifo(dwc_otg_core_if_t * _core_if, const int _num);
-+extern void dwc_otg_flush_rx_fifo(dwc_otg_core_if_t * _core_if);
-+extern void dwc_otg_core_reset(dwc_otg_core_if_t * _core_if);
-+
-+/**
-+ * This function returns the Core Interrupt register.
-+ */
-+static inline uint32_t dwc_otg_read_core_intr(dwc_otg_core_if_t * core_if)
-+{
-+ return (DWC_READ_REG32(&core_if->core_global_regs->gintsts) &
-+ DWC_READ_REG32(&core_if->core_global_regs->gintmsk));
-+}
-+
-+/**
-+ * This function returns the OTG Interrupt register.
-+ */
-+static inline uint32_t dwc_otg_read_otg_intr(dwc_otg_core_if_t * core_if)
-+{
-+ return (DWC_READ_REG32(&core_if->core_global_regs->gotgint));
-+}
-+
-+/**
-+ * This function reads the Device All Endpoints Interrupt register and
-+ * returns the IN endpoint interrupt bits.
-+ */
-+static inline uint32_t dwc_otg_read_dev_all_in_ep_intr(dwc_otg_core_if_t *
-+ core_if)
-+{
-+
-+ uint32_t v;
-+
-+ if (core_if->multiproc_int_enable) {
-+ v = DWC_READ_REG32(&core_if->dev_if->
-+ dev_global_regs->deachint) &
-+ DWC_READ_REG32(&core_if->
-+ dev_if->dev_global_regs->deachintmsk);
-+ } else {
-+ v = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->daint) &
-+ DWC_READ_REG32(&core_if->dev_if->dev_global_regs->daintmsk);
-+ }
-+ return (v & 0xffff);
-+}
-+
-+/**
-+ * This function reads the Device All Endpoints Interrupt register and
-+ * returns the OUT endpoint interrupt bits.
-+ */
-+static inline uint32_t dwc_otg_read_dev_all_out_ep_intr(dwc_otg_core_if_t *
-+ core_if)
-+{
-+ uint32_t v;
-+
-+ if (core_if->multiproc_int_enable) {
-+ v = DWC_READ_REG32(&core_if->dev_if->
-+ dev_global_regs->deachint) &
-+ DWC_READ_REG32(&core_if->
-+ dev_if->dev_global_regs->deachintmsk);
-+ } else {
-+ v = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->daint) &
-+ DWC_READ_REG32(&core_if->dev_if->dev_global_regs->daintmsk);
-+ }
-+
-+ return ((v & 0xffff0000) >> 16);
-+}
-+
-+/**
-+ * This function returns the Device IN EP Interrupt register
-+ */
-+static inline uint32_t dwc_otg_read_dev_in_ep_intr(dwc_otg_core_if_t * core_if,
-+ dwc_ep_t * ep)
-+{
-+ dwc_otg_dev_if_t *dev_if = core_if->dev_if;
-+ uint32_t v, msk, emp;
-+
-+ if (core_if->multiproc_int_enable) {
-+ msk =
-+ DWC_READ_REG32(&dev_if->
-+ dev_global_regs->diepeachintmsk[ep->num]);
-+ emp =
-+ DWC_READ_REG32(&dev_if->
-+ dev_global_regs->dtknqr4_fifoemptymsk);
-+ msk |= ((emp >> ep->num) & 0x1) << 7;
-+ v = DWC_READ_REG32(&dev_if->in_ep_regs[ep->num]->diepint) & msk;
-+ } else {
-+ msk = DWC_READ_REG32(&dev_if->dev_global_regs->diepmsk);
-+ emp =
-+ DWC_READ_REG32(&dev_if->
-+ dev_global_regs->dtknqr4_fifoemptymsk);
-+ msk |= ((emp >> ep->num) & 0x1) << 7;
-+ v = DWC_READ_REG32(&dev_if->in_ep_regs[ep->num]->diepint) & msk;
-+ }
-+
-+ return v;
-+}
-+
-+/**
-+ * This function returns the Device OUT EP Interrupt register
-+ */
-+static inline uint32_t dwc_otg_read_dev_out_ep_intr(dwc_otg_core_if_t *
-+ _core_if, dwc_ep_t * _ep)
-+{
-+ dwc_otg_dev_if_t *dev_if = _core_if->dev_if;
-+ uint32_t v;
-+ doepmsk_data_t msk = {.d32 = 0 };
-+
-+ if (_core_if->multiproc_int_enable) {
-+ msk.d32 =
-+ DWC_READ_REG32(&dev_if->
-+ dev_global_regs->doepeachintmsk[_ep->num]);
-+ if (_core_if->pti_enh_enable) {
-+ msk.b.pktdrpsts = 1;
-+ }
-+ v = DWC_READ_REG32(&dev_if->
-+ out_ep_regs[_ep->num]->doepint) & msk.d32;
-+ } else {
-+ msk.d32 = DWC_READ_REG32(&dev_if->dev_global_regs->doepmsk);
-+ if (_core_if->pti_enh_enable) {
-+ msk.b.pktdrpsts = 1;
-+ }
-+ v = DWC_READ_REG32(&dev_if->
-+ out_ep_regs[_ep->num]->doepint) & msk.d32;
-+ }
-+ return v;
-+}
-+
-+/**
-+ * This function returns the Host All Channel Interrupt register
-+ */
-+static inline uint32_t dwc_otg_read_host_all_channels_intr(dwc_otg_core_if_t *
-+ _core_if)
-+{
-+ return (DWC_READ_REG32(&_core_if->host_if->host_global_regs->haint));
-+}
-+
-+static inline uint32_t dwc_otg_read_host_channel_intr(dwc_otg_core_if_t *
-+ _core_if, dwc_hc_t * _hc)
-+{
-+ return (DWC_READ_REG32
-+ (&_core_if->host_if->hc_regs[_hc->hc_num]->hcint));
-+}
-+
-+/**
-+ * This function returns the mode of the operation, host or device.
-+ *
-+ * @return 0 - Device Mode, 1 - Host Mode
-+ */
-+static inline uint32_t dwc_otg_mode(dwc_otg_core_if_t * _core_if)
-+{
-+ return (DWC_READ_REG32(&_core_if->core_global_regs->gintsts) & 0x1);
-+}
-+
-+/**@}*/
-+
-+/**
-+ * DWC_otg CIL callback structure. This structure allows the HCD and
-+ * PCD to register functions used for starting and stopping the PCD
-+ * and HCD for role change on for a DRD.
-+ */
-+typedef struct dwc_otg_cil_callbacks {
-+ /** Start function for role change */
-+ int (*start) (void *_p);
-+ /** Stop Function for role change */
-+ int (*stop) (void *_p);
-+ /** Disconnect Function for role change */
-+ int (*disconnect) (void *_p);
-+ /** Resume/Remote wakeup Function */
-+ int (*resume_wakeup) (void *_p);
-+ /** Suspend function */
-+ int (*suspend) (void *_p);
-+ /** Session Start (SRP) */
-+ int (*session_start) (void *_p);
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+ /** Sleep (switch to L0 state) */
-+ int (*sleep) (void *_p);
-+#endif
-+ /** Pointer passed to start() and stop() */
-+ void *p;
-+} dwc_otg_cil_callbacks_t;
-+
-+extern void dwc_otg_cil_register_pcd_callbacks(dwc_otg_core_if_t * _core_if,
-+ dwc_otg_cil_callbacks_t * _cb,
-+ void *_p);
-+extern void dwc_otg_cil_register_hcd_callbacks(dwc_otg_core_if_t * _core_if,
-+ dwc_otg_cil_callbacks_t * _cb,
-+ void *_p);
-+
-+void dwc_otg_initiate_srp(dwc_otg_core_if_t * core_if);
-+
-+//////////////////////////////////////////////////////////////////////
-+/** Start the HCD. Helper function for using the HCD callbacks.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ */
-+static inline void cil_hcd_start(dwc_otg_core_if_t * core_if)
-+{
-+ if (core_if->hcd_cb && core_if->hcd_cb->start) {
-+ core_if->hcd_cb->start(core_if->hcd_cb->p);
-+ }
-+}
-+
-+/** Stop the HCD. Helper function for using the HCD callbacks.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ */
-+static inline void cil_hcd_stop(dwc_otg_core_if_t * core_if)
-+{
-+ if (core_if->hcd_cb && core_if->hcd_cb->stop) {
-+ core_if->hcd_cb->stop(core_if->hcd_cb->p);
-+ }
-+}
-+
-+/** Disconnect the HCD. Helper function for using the HCD callbacks.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ */
-+static inline void cil_hcd_disconnect(dwc_otg_core_if_t * core_if)
-+{
-+ if (core_if->hcd_cb && core_if->hcd_cb->disconnect) {
-+ core_if->hcd_cb->disconnect(core_if->hcd_cb->p);
-+ }
-+}
-+
-+/** Inform the HCD the a New Session has begun. Helper function for
-+ * using the HCD callbacks.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ */
-+static inline void cil_hcd_session_start(dwc_otg_core_if_t * core_if)
-+{
-+ if (core_if->hcd_cb && core_if->hcd_cb->session_start) {
-+ core_if->hcd_cb->session_start(core_if->hcd_cb->p);
-+ }
-+}
-+
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+/**
-+ * Inform the HCD about LPM sleep.
-+ * Helper function for using the HCD callbacks.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ */
-+static inline void cil_hcd_sleep(dwc_otg_core_if_t * core_if)
-+{
-+ if (core_if->hcd_cb && core_if->hcd_cb->sleep) {
-+ core_if->hcd_cb->sleep(core_if->hcd_cb->p);
-+ }
-+}
-+#endif
-+
-+/** Resume the HCD. Helper function for using the HCD callbacks.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ */
-+static inline void cil_hcd_resume(dwc_otg_core_if_t * core_if)
-+{
-+ if (core_if->hcd_cb && core_if->hcd_cb->resume_wakeup) {
-+ core_if->hcd_cb->resume_wakeup(core_if->hcd_cb->p);
-+ }
-+}
-+
-+/** Start the PCD. Helper function for using the PCD callbacks.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ */
-+static inline void cil_pcd_start(dwc_otg_core_if_t * core_if)
-+{
-+ if (core_if->pcd_cb && core_if->pcd_cb->start) {
-+ core_if->pcd_cb->start(core_if->pcd_cb->p);
-+ }
-+}
-+
-+/** Stop the PCD. Helper function for using the PCD callbacks.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ */
-+static inline void cil_pcd_stop(dwc_otg_core_if_t * core_if)
-+{
-+ if (core_if->pcd_cb && core_if->pcd_cb->stop) {
-+ core_if->pcd_cb->stop(core_if->pcd_cb->p);
-+ }
-+}
-+
-+/** Suspend the PCD. Helper function for using the PCD callbacks.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ */
-+static inline void cil_pcd_suspend(dwc_otg_core_if_t * core_if)
-+{
-+ if (core_if->pcd_cb && core_if->pcd_cb->suspend) {
-+ core_if->pcd_cb->suspend(core_if->pcd_cb->p);
-+ }
-+}
-+
-+/** Resume the PCD. Helper function for using the PCD callbacks.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ */
-+static inline void cil_pcd_resume(dwc_otg_core_if_t * core_if)
-+{
-+ if (core_if->pcd_cb && core_if->pcd_cb->resume_wakeup) {
-+ core_if->pcd_cb->resume_wakeup(core_if->pcd_cb->p);
-+ }
-+}
-+
-+//////////////////////////////////////////////////////////////////////
-+
-+#endif
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_cil_intr.c
-@@ -0,0 +1,1594 @@
-+/* ==========================================================================
-+ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_cil_intr.c $
-+ * $Revision: #32 $
-+ * $Date: 2012/08/10 $
-+ * $Change: 2047372 $
-+ *
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+
-+/** @file
-+ *
-+ * The Core Interface Layer provides basic services for accessing and
-+ * managing the DWC_otg hardware. These services are used by both the
-+ * Host Controller Driver and the Peripheral Controller Driver.
-+ *
-+ * This file contains the Common Interrupt handlers.
-+ */
-+#include "dwc_os.h"
-+#include "dwc_otg_regs.h"
-+#include "dwc_otg_cil.h"
-+#include "dwc_otg_driver.h"
-+#include "dwc_otg_pcd.h"
-+#include "dwc_otg_hcd.h"
-+
-+#ifdef DEBUG
-+inline const char *op_state_str(dwc_otg_core_if_t * core_if)
-+{
-+ return (core_if->op_state == A_HOST ? "a_host" :
-+ (core_if->op_state == A_SUSPEND ? "a_suspend" :
-+ (core_if->op_state == A_PERIPHERAL ? "a_peripheral" :
-+ (core_if->op_state == B_PERIPHERAL ? "b_peripheral" :
-+ (core_if->op_state == B_HOST ? "b_host" : "unknown")))));
-+}
-+#endif
-+
-+/** This function will log a debug message
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ */
-+int32_t dwc_otg_handle_mode_mismatch_intr(dwc_otg_core_if_t * core_if)
-+{
-+ gintsts_data_t gintsts;
-+ DWC_WARN("Mode Mismatch Interrupt: currently in %s mode\n",
-+ dwc_otg_mode(core_if) ? "Host" : "Device");
-+
-+ /* Clear interrupt */
-+ gintsts.d32 = 0;
-+ gintsts.b.modemismatch = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32);
-+ return 1;
-+}
-+
-+/**
-+ * This function handles the OTG Interrupts. It reads the OTG
-+ * Interrupt Register (GOTGINT) to determine what interrupt has
-+ * occurred.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ */
-+int32_t dwc_otg_handle_otg_intr(dwc_otg_core_if_t * core_if)
-+{
-+ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs;
-+ gotgint_data_t gotgint;
-+ gotgctl_data_t gotgctl;
-+ gintmsk_data_t gintmsk;
-+ gpwrdn_data_t gpwrdn;
-+
-+ gotgint.d32 = DWC_READ_REG32(&global_regs->gotgint);
-+ gotgctl.d32 = DWC_READ_REG32(&global_regs->gotgctl);
-+ DWC_DEBUGPL(DBG_CIL, "++OTG Interrupt gotgint=%0x [%s]\n", gotgint.d32,
-+ op_state_str(core_if));
-+
-+ if (gotgint.b.sesenddet) {
-+ DWC_DEBUGPL(DBG_ANY, " ++OTG Interrupt: "
-+ "Session End Detected++ (%s)\n",
-+ op_state_str(core_if));
-+ gotgctl.d32 = DWC_READ_REG32(&global_regs->gotgctl);
-+
-+ if (core_if->op_state == B_HOST) {
-+ cil_pcd_start(core_if);
-+ core_if->op_state = B_PERIPHERAL;
-+ } else {
-+ /* If not B_HOST and Device HNP still set. HNP
-+ * Did not succeed!*/
-+ if (gotgctl.b.devhnpen) {
-+ DWC_DEBUGPL(DBG_ANY, "Session End Detected\n");
-+ __DWC_ERROR("Device Not Connected/Responding!\n");
-+ }
-+
-+ /* If Session End Detected the B-Cable has
-+ * been disconnected. */
-+ /* Reset PCD and Gadget driver to a
-+ * clean state. */
-+ core_if->lx_state = DWC_OTG_L0;
-+ DWC_SPINUNLOCK(core_if->lock);
-+ cil_pcd_stop(core_if);
-+ DWC_SPINLOCK(core_if->lock);
-+
-+ if (core_if->adp_enable) {
-+ if (core_if->power_down == 2) {
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnswtch = 1;
-+ DWC_MODIFY_REG32(&core_if->
-+ core_global_regs->
-+ gpwrdn, gpwrdn.d32, 0);
-+ }
-+
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuintsel = 1;
-+ gpwrdn.b.pmuactv = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->
-+ gpwrdn, 0, gpwrdn.d32);
-+
-+ dwc_otg_adp_sense_start(core_if);
-+ }
-+ }
-+
-+ gotgctl.d32 = 0;
-+ gotgctl.b.devhnpen = 1;
-+ DWC_MODIFY_REG32(&global_regs->gotgctl, gotgctl.d32, 0);
-+ }
-+ if (gotgint.b.sesreqsucstschng) {
-+ DWC_DEBUGPL(DBG_ANY, " ++OTG Interrupt: "
-+ "Session Reqeust Success Status Change++\n");
-+ gotgctl.d32 = DWC_READ_REG32(&global_regs->gotgctl);
-+ if (gotgctl.b.sesreqscs) {
-+
-+ if ((core_if->core_params->phy_type ==
-+ DWC_PHY_TYPE_PARAM_FS) && (core_if->core_params->i2c_enable)) {
-+ core_if->srp_success = 1;
-+ } else {
-+ DWC_SPINUNLOCK(core_if->lock);
-+ cil_pcd_resume(core_if);
-+ DWC_SPINLOCK(core_if->lock);
-+ /* Clear Session Request */
-+ gotgctl.d32 = 0;
-+ gotgctl.b.sesreq = 1;
-+ DWC_MODIFY_REG32(&global_regs->gotgctl,
-+ gotgctl.d32, 0);
-+ }
-+ }
-+ }
-+ if (gotgint.b.hstnegsucstschng) {
-+ /* Print statements during the HNP interrupt handling
-+ * can cause it to fail.*/
-+ gotgctl.d32 = DWC_READ_REG32(&global_regs->gotgctl);
-+ /* WA for 3.00a- HW is not setting cur_mode, even sometimes
-+ * this does not help*/
-+ if (core_if->snpsid >= OTG_CORE_REV_3_00a)
-+ dwc_udelay(100);
-+ if (gotgctl.b.hstnegscs) {
-+ if (dwc_otg_is_host_mode(core_if)) {
-+ core_if->op_state = B_HOST;
-+ /*
-+ * Need to disable SOF interrupt immediately.
-+ * When switching from device to host, the PCD
-+ * interrupt handler won't handle the
-+ * interrupt if host mode is already set. The
-+ * HCD interrupt handler won't get called if
-+ * the HCD state is HALT. This means that the
-+ * interrupt does not get handled and Linux
-+ * complains loudly.
-+ */
-+ gintmsk.d32 = 0;
-+ gintmsk.b.sofintr = 1;
-+ DWC_MODIFY_REG32(&global_regs->gintmsk,
-+ gintmsk.d32, 0);
-+ /* Call callback function with spin lock released */
-+ DWC_SPINUNLOCK(core_if->lock);
-+ cil_pcd_stop(core_if);
-+ /*
-+ * Initialize the Core for Host mode.
-+ */
-+ cil_hcd_start(core_if);
-+ DWC_SPINLOCK(core_if->lock);
-+ core_if->op_state = B_HOST;
-+ }
-+ } else {
-+ gotgctl.d32 = 0;
-+ gotgctl.b.hnpreq = 1;
-+ gotgctl.b.devhnpen = 1;
-+ DWC_MODIFY_REG32(&global_regs->gotgctl, gotgctl.d32, 0);
-+ DWC_DEBUGPL(DBG_ANY, "HNP Failed\n");
-+ __DWC_ERROR("Device Not Connected/Responding\n");
-+ }
-+ }
-+ if (gotgint.b.hstnegdet) {
-+ /* The disconnect interrupt is set at the same time as
-+ * Host Negotiation Detected. During the mode
-+ * switch all interrupts are cleared so the disconnect
-+ * interrupt handler will not get executed.
-+ */
-+ DWC_DEBUGPL(DBG_ANY, " ++OTG Interrupt: "
-+ "Host Negotiation Detected++ (%s)\n",
-+ (dwc_otg_is_host_mode(core_if) ? "Host" :
-+ "Device"));
-+ if (dwc_otg_is_device_mode(core_if)) {
-+ DWC_DEBUGPL(DBG_ANY, "a_suspend->a_peripheral (%d)\n",
-+ core_if->op_state);
-+ DWC_SPINUNLOCK(core_if->lock);
-+ cil_hcd_disconnect(core_if);
-+ cil_pcd_start(core_if);
-+ DWC_SPINLOCK(core_if->lock);
-+ core_if->op_state = A_PERIPHERAL;
-+ } else {
-+ /*
-+ * Need to disable SOF interrupt immediately. When
-+ * switching from device to host, the PCD interrupt
-+ * handler won't handle the interrupt if host mode is
-+ * already set. The HCD interrupt handler won't get
-+ * called if the HCD state is HALT. This means that
-+ * the interrupt does not get handled and Linux
-+ * complains loudly.
-+ */
-+ gintmsk.d32 = 0;
-+ gintmsk.b.sofintr = 1;
-+ DWC_MODIFY_REG32(&global_regs->gintmsk, gintmsk.d32, 0);
-+ DWC_SPINUNLOCK(core_if->lock);
-+ cil_pcd_stop(core_if);
-+ cil_hcd_start(core_if);
-+ DWC_SPINLOCK(core_if->lock);
-+ core_if->op_state = A_HOST;
-+ }
-+ }
-+ if (gotgint.b.adevtoutchng) {
-+ DWC_DEBUGPL(DBG_ANY, " ++OTG Interrupt: "
-+ "A-Device Timeout Change++\n");
-+ }
-+ if (gotgint.b.debdone) {
-+ DWC_DEBUGPL(DBG_ANY, " ++OTG Interrupt: " "Debounce Done++\n");
-+ }
-+
-+ /* Clear GOTGINT */
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gotgint, gotgint.d32);
-+
-+ return 1;
-+}
-+
-+void w_conn_id_status_change(void *p)
-+{
-+ dwc_otg_core_if_t *core_if = p;
-+ uint32_t count = 0;
-+ gotgctl_data_t gotgctl = {.d32 = 0 };
-+
-+ gotgctl.d32 = DWC_READ_REG32(&core_if->core_global_regs->gotgctl);
-+ DWC_DEBUGPL(DBG_CIL, "gotgctl=%0x\n", gotgctl.d32);
-+ DWC_DEBUGPL(DBG_CIL, "gotgctl.b.conidsts=%d\n", gotgctl.b.conidsts);
-+
-+ /* B-Device connector (Device Mode) */
-+ if (gotgctl.b.conidsts) {
-+ /* Wait for switch to device mode. */
-+ while (!dwc_otg_is_device_mode(core_if)) {
-+ DWC_PRINTF("Waiting for Peripheral Mode, Mode=%s\n",
-+ (dwc_otg_is_host_mode(core_if) ? "Host" :
-+ "Peripheral"));
-+ dwc_mdelay(100);
-+ if (++count > 10000)
-+ break;
-+ }
-+ DWC_ASSERT(++count < 10000,
-+ "Connection id status change timed out");
-+ core_if->op_state = B_PERIPHERAL;
-+ dwc_otg_core_init(core_if);
-+ dwc_otg_enable_global_interrupts(core_if);
-+ cil_pcd_start(core_if);
-+ } else {
-+ /* A-Device connector (Host Mode) */
-+ while (!dwc_otg_is_host_mode(core_if)) {
-+ DWC_PRINTF("Waiting for Host Mode, Mode=%s\n",
-+ (dwc_otg_is_host_mode(core_if) ? "Host" :
-+ "Peripheral"));
-+ dwc_mdelay(100);
-+ if (++count > 10000)
-+ break;
-+ }
-+ DWC_ASSERT(++count < 10000,
-+ "Connection id status change timed out");
-+ core_if->op_state = A_HOST;
-+ /*
-+ * Initialize the Core for Host mode.
-+ */
-+ dwc_otg_core_init(core_if);
-+ dwc_otg_enable_global_interrupts(core_if);
-+ cil_hcd_start(core_if);
-+ }
-+}
-+
-+/**
-+ * This function handles the Connector ID Status Change Interrupt. It
-+ * reads the OTG Interrupt Register (GOTCTL) to determine whether this
-+ * is a Device to Host Mode transition or a Host Mode to Device
-+ * Transition.
-+ *
-+ * This only occurs when the cable is connected/removed from the PHY
-+ * connector.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ */
-+int32_t dwc_otg_handle_conn_id_status_change_intr(dwc_otg_core_if_t * core_if)
-+{
-+
-+ /*
-+ * Need to disable SOF interrupt immediately. If switching from device
-+ * to host, the PCD interrupt handler won't handle the interrupt if
-+ * host mode is already set. The HCD interrupt handler won't get
-+ * called if the HCD state is HALT. This means that the interrupt does
-+ * not get handled and Linux complains loudly.
-+ */
-+ gintmsk_data_t gintmsk = {.d32 = 0 };
-+ gintsts_data_t gintsts = {.d32 = 0 };
-+
-+ gintmsk.b.sofintr = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gintmsk, gintmsk.d32, 0);
-+
-+ DWC_DEBUGPL(DBG_CIL,
-+ " ++Connector ID Status Change Interrupt++ (%s)\n",
-+ (dwc_otg_is_host_mode(core_if) ? "Host" : "Device"));
-+
-+ DWC_SPINUNLOCK(core_if->lock);
-+
-+ /*
-+ * Need to schedule a work, as there are possible DELAY function calls
-+ * Release lock before scheduling workq as it holds spinlock during scheduling
-+ */
-+
-+ DWC_WORKQ_SCHEDULE(core_if->wq_otg, w_conn_id_status_change,
-+ core_if, "connection id status change");
-+ DWC_SPINLOCK(core_if->lock);
-+
-+ /* Set flag and clear interrupt */
-+ gintsts.b.conidstschng = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32);
-+
-+ return 1;
-+}
-+
-+/**
-+ * This interrupt indicates that a device is initiating the Session
-+ * Request Protocol to request the host to turn on bus power so a new
-+ * session can begin. The handler responds by turning on bus power. If
-+ * the DWC_otg controller is in low power mode, the handler brings the
-+ * controller out of low power mode before turning on bus power.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ */
-+int32_t dwc_otg_handle_session_req_intr(dwc_otg_core_if_t * core_if)
-+{
-+ gintsts_data_t gintsts;
-+
-+#ifndef DWC_HOST_ONLY
-+ DWC_DEBUGPL(DBG_ANY, "++Session Request Interrupt++\n");
-+
-+ if (dwc_otg_is_device_mode(core_if)) {
-+ DWC_PRINTF("SRP: Device mode\n");
-+ } else {
-+ hprt0_data_t hprt0;
-+ DWC_PRINTF("SRP: Host mode\n");
-+
-+ /* Turn on the port power bit. */
-+ hprt0.d32 = dwc_otg_read_hprt0(core_if);
-+ hprt0.b.prtpwr = 1;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+
-+ /* Start the Connection timer. So a message can be displayed
-+ * if connect does not occur within 10 seconds. */
-+ cil_hcd_session_start(core_if);
-+ }
-+#endif
-+
-+ /* Clear interrupt */
-+ gintsts.d32 = 0;
-+ gintsts.b.sessreqintr = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32);
-+
-+ return 1;
-+}
-+
-+void w_wakeup_detected(void *p)
-+{
-+ dwc_otg_core_if_t *core_if = (dwc_otg_core_if_t *) p;
-+ /*
-+ * Clear the Resume after 70ms. (Need 20 ms minimum. Use 70 ms
-+ * so that OPT tests pass with all PHYs).
-+ */
-+ hprt0_data_t hprt0 = {.d32 = 0 };
-+#if 0
-+ pcgcctl_data_t pcgcctl = {.d32 = 0 };
-+ /* Restart the Phy Clock */
-+ pcgcctl.b.stoppclk = 1;
-+ DWC_MODIFY_REG32(core_if->pcgcctl, pcgcctl.d32, 0);
-+ dwc_udelay(10);
-+#endif //0
-+ hprt0.d32 = dwc_otg_read_hprt0(core_if);
-+ DWC_DEBUGPL(DBG_ANY, "Resume: HPRT0=%0x\n", hprt0.d32);
-+// dwc_mdelay(70);
-+ hprt0.b.prtres = 0; /* Resume */
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+ DWC_DEBUGPL(DBG_ANY, "Clear Resume: HPRT0=%0x\n",
-+ DWC_READ_REG32(core_if->host_if->hprt0));
-+
-+ cil_hcd_resume(core_if);
-+
-+ /** Change to L0 state*/
-+ core_if->lx_state = DWC_OTG_L0;
-+}
-+
-+/**
-+ * This interrupt indicates that the DWC_otg controller has detected a
-+ * resume or remote wakeup sequence. If the DWC_otg controller is in
-+ * low power mode, the handler must brings the controller out of low
-+ * power mode. The controller automatically begins resume
-+ * signaling. The handler schedules a time to stop resume signaling.
-+ */
-+int32_t dwc_otg_handle_wakeup_detected_intr(dwc_otg_core_if_t * core_if)
-+{
-+ gintsts_data_t gintsts;
-+
-+ DWC_DEBUGPL(DBG_ANY,
-+ "++Resume and Remote Wakeup Detected Interrupt++\n");
-+
-+ DWC_PRINTF("%s lxstate = %d\n", __func__, core_if->lx_state);
-+
-+ if (dwc_otg_is_device_mode(core_if)) {
-+ dctl_data_t dctl = {.d32 = 0 };
-+ DWC_DEBUGPL(DBG_PCD, "DSTS=0x%0x\n",
-+ DWC_READ_REG32(&core_if->dev_if->dev_global_regs->
-+ dsts));
-+ if (core_if->lx_state == DWC_OTG_L2) {
-+#ifdef PARTIAL_POWER_DOWN
-+ if (core_if->hwcfg4.b.power_optimiz) {
-+ pcgcctl_data_t power = {.d32 = 0 };
-+
-+ power.d32 = DWC_READ_REG32(core_if->pcgcctl);
-+ DWC_DEBUGPL(DBG_CIL, "PCGCCTL=%0x\n",
-+ power.d32);
-+
-+ power.b.stoppclk = 0;
-+ DWC_WRITE_REG32(core_if->pcgcctl, power.d32);
-+
-+ power.b.pwrclmp = 0;
-+ DWC_WRITE_REG32(core_if->pcgcctl, power.d32);
-+
-+ power.b.rstpdwnmodule = 0;
-+ DWC_WRITE_REG32(core_if->pcgcctl, power.d32);
-+ }
-+#endif
-+ /* Clear the Remote Wakeup Signaling */
-+ dctl.b.rmtwkupsig = 1;
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->
-+ dctl, dctl.d32, 0);
-+
-+ DWC_SPINUNLOCK(core_if->lock);
-+ if (core_if->pcd_cb && core_if->pcd_cb->resume_wakeup) {
-+ core_if->pcd_cb->resume_wakeup(core_if->pcd_cb->p);
-+ }
-+ DWC_SPINLOCK(core_if->lock);
-+ } else {
-+ glpmcfg_data_t lpmcfg;
-+ lpmcfg.d32 =
-+ DWC_READ_REG32(&core_if->core_global_regs->glpmcfg);
-+ lpmcfg.b.hird_thres &= (~(1 << 4));
-+ DWC_WRITE_REG32(&core_if->core_global_regs->glpmcfg,
-+ lpmcfg.d32);
-+ }
-+ /** Change to L0 state*/
-+ core_if->lx_state = DWC_OTG_L0;
-+ } else {
-+ if (core_if->lx_state != DWC_OTG_L1) {
-+ pcgcctl_data_t pcgcctl = {.d32 = 0 };
-+
-+ /* Restart the Phy Clock */
-+ pcgcctl.b.stoppclk = 1;
-+ DWC_MODIFY_REG32(core_if->pcgcctl, pcgcctl.d32, 0);
-+ DWC_TIMER_SCHEDULE(core_if->wkp_timer, 71);
-+ } else {
-+ /** Change to L0 state*/
-+ core_if->lx_state = DWC_OTG_L0;
-+ }
-+ }
-+
-+ /* Clear interrupt */
-+ gintsts.d32 = 0;
-+ gintsts.b.wkupintr = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32);
-+
-+ return 1;
-+}
-+
-+/**
-+ * This interrupt indicates that the Wakeup Logic has detected a
-+ * Device disconnect.
-+ */
-+static int32_t dwc_otg_handle_pwrdn_disconnect_intr(dwc_otg_core_if_t *core_if)
-+{
-+ gpwrdn_data_t gpwrdn = { .d32 = 0 };
-+ gpwrdn_data_t gpwrdn_temp = { .d32 = 0 };
-+ gpwrdn_temp.d32 = DWC_READ_REG32(&core_if->core_global_regs->gpwrdn);
-+
-+ DWC_PRINTF("%s called\n", __FUNCTION__);
-+
-+ if (!core_if->hibernation_suspend) {
-+ DWC_PRINTF("Already exited from Hibernation\n");
-+ return 1;
-+ }
-+
-+ /* Switch on the voltage to the core */
-+ gpwrdn.b.pwrdnswtch = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ dwc_udelay(10);
-+
-+ /* Reset the core */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnrstn = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ dwc_udelay(10);
-+
-+ /* Disable power clamps*/
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnclmp = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+
-+ /* Remove reset the core signal */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnrstn = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32);
-+ dwc_udelay(10);
-+
-+ /* Disable PMU interrupt */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuintsel = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+
-+ core_if->hibernation_suspend = 0;
-+
-+ /* Disable PMU */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuactv = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ dwc_udelay(10);
-+
-+ if (gpwrdn_temp.b.idsts) {
-+ core_if->op_state = B_PERIPHERAL;
-+ dwc_otg_core_init(core_if);
-+ dwc_otg_enable_global_interrupts(core_if);
-+ cil_pcd_start(core_if);
-+ } else {
-+ core_if->op_state = A_HOST;
-+ dwc_otg_core_init(core_if);
-+ dwc_otg_enable_global_interrupts(core_if);
-+ cil_hcd_start(core_if);
-+ }
-+
-+ return 1;
-+}
-+
-+/**
-+ * This interrupt indicates that the Wakeup Logic has detected a
-+ * remote wakeup sequence.
-+ */
-+static int32_t dwc_otg_handle_pwrdn_wakeup_detected_intr(dwc_otg_core_if_t * core_if)
-+{
-+ gpwrdn_data_t gpwrdn = {.d32 = 0 };
-+ DWC_DEBUGPL(DBG_ANY,
-+ "++Powerdown Remote Wakeup Detected Interrupt++\n");
-+
-+ if (!core_if->hibernation_suspend) {
-+ DWC_PRINTF("Already exited from Hibernation\n");
-+ return 1;
-+ }
-+
-+ gpwrdn.d32 = DWC_READ_REG32(&core_if->core_global_regs->gpwrdn);
-+ if (gpwrdn.b.idsts) { // Device Mode
-+ if ((core_if->power_down == 2)
-+ && (core_if->hibernation_suspend == 1)) {
-+ dwc_otg_device_hibernation_restore(core_if, 0, 0);
-+ }
-+ } else {
-+ if ((core_if->power_down == 2)
-+ && (core_if->hibernation_suspend == 1)) {
-+ dwc_otg_host_hibernation_restore(core_if, 1, 0);
-+ }
-+ }
-+ return 1;
-+}
-+
-+static int32_t dwc_otg_handle_pwrdn_idsts_change(dwc_otg_device_t *otg_dev)
-+{
-+ gpwrdn_data_t gpwrdn = {.d32 = 0 };
-+ gpwrdn_data_t gpwrdn_temp = {.d32 = 0 };
-+ dwc_otg_core_if_t *core_if = otg_dev->core_if;
-+
-+ DWC_DEBUGPL(DBG_ANY, "%s called\n", __FUNCTION__);
-+ gpwrdn_temp.d32 = DWC_READ_REG32(&core_if->core_global_regs->gpwrdn);
-+ if (core_if->power_down == 2) {
-+ if (!core_if->hibernation_suspend) {
-+ DWC_PRINTF("Already exited from Hibernation\n");
-+ return 1;
-+ }
-+ DWC_DEBUGPL(DBG_ANY, "Exit from hibernation on ID sts change\n");
-+ /* Switch on the voltage to the core */
-+ gpwrdn.b.pwrdnswtch = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ dwc_udelay(10);
-+
-+ /* Reset the core */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnrstn = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ dwc_udelay(10);
-+
-+ /* Disable power clamps */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnclmp = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+
-+ /* Remove reset the core signal */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnrstn = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32);
-+ dwc_udelay(10);
-+
-+ /* Disable PMU interrupt */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuintsel = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+
-+ /*Indicates that we are exiting from hibernation */
-+ core_if->hibernation_suspend = 0;
-+
-+ /* Disable PMU */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuactv = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ dwc_udelay(10);
-+
-+ gpwrdn.d32 = core_if->gr_backup->gpwrdn_local;
-+ if (gpwrdn.b.dis_vbus == 1) {
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.dis_vbus = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ }
-+
-+ if (gpwrdn_temp.b.idsts) {
-+ core_if->op_state = B_PERIPHERAL;
-+ dwc_otg_core_init(core_if);
-+ dwc_otg_enable_global_interrupts(core_if);
-+ cil_pcd_start(core_if);
-+ } else {
-+ core_if->op_state = A_HOST;
-+ dwc_otg_core_init(core_if);
-+ dwc_otg_enable_global_interrupts(core_if);
-+ cil_hcd_start(core_if);
-+ }
-+ }
-+
-+ if (core_if->adp_enable) {
-+ uint8_t is_host = 0;
-+ DWC_SPINUNLOCK(core_if->lock);
-+ /* Change the core_if's lock to hcd/pcd lock depend on mode? */
-+#ifndef DWC_HOST_ONLY
-+ if (gpwrdn_temp.b.idsts)
-+ core_if->lock = otg_dev->pcd->lock;
-+#endif
-+#ifndef DWC_DEVICE_ONLY
-+ if (!gpwrdn_temp.b.idsts) {
-+ core_if->lock = otg_dev->hcd->lock;
-+ is_host = 1;
-+ }
-+#endif
-+ DWC_PRINTF("RESTART ADP\n");
-+ if (core_if->adp.probe_enabled)
-+ dwc_otg_adp_probe_stop(core_if);
-+ if (core_if->adp.sense_enabled)
-+ dwc_otg_adp_sense_stop(core_if);
-+ if (core_if->adp.sense_timer_started)
-+ DWC_TIMER_CANCEL(core_if->adp.sense_timer);
-+ if (core_if->adp.vbuson_timer_started)
-+ DWC_TIMER_CANCEL(core_if->adp.vbuson_timer);
-+ core_if->adp.probe_timer_values[0] = -1;
-+ core_if->adp.probe_timer_values[1] = -1;
-+ core_if->adp.sense_timer_started = 0;
-+ core_if->adp.vbuson_timer_started = 0;
-+ core_if->adp.probe_counter = 0;
-+ core_if->adp.gpwrdn = 0;
-+
-+ /* Disable PMU and restart ADP */
-+ gpwrdn_temp.d32 = 0;
-+ gpwrdn_temp.b.pmuactv = 1;
-+ gpwrdn_temp.b.pmuintsel = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ DWC_PRINTF("Check point 1\n");
-+ dwc_mdelay(110);
-+ dwc_otg_adp_start(core_if, is_host);
-+ DWC_SPINLOCK(core_if->lock);
-+ }
-+
-+
-+ return 1;
-+}
-+
-+static int32_t dwc_otg_handle_pwrdn_session_change(dwc_otg_core_if_t * core_if)
-+{
-+ gpwrdn_data_t gpwrdn = {.d32 = 0 };
-+ int32_t otg_cap_param = core_if->core_params->otg_cap;
-+ DWC_DEBUGPL(DBG_ANY, "%s called\n", __FUNCTION__);
-+
-+ gpwrdn.d32 = DWC_READ_REG32(&core_if->core_global_regs->gpwrdn);
-+ if (core_if->power_down == 2) {
-+ if (!core_if->hibernation_suspend) {
-+ DWC_PRINTF("Already exited from Hibernation\n");
-+ return 1;
-+ }
-+
-+ if ((otg_cap_param != DWC_OTG_CAP_PARAM_HNP_SRP_CAPABLE ||
-+ otg_cap_param != DWC_OTG_CAP_PARAM_SRP_ONLY_CAPABLE) &&
-+ gpwrdn.b.bsessvld == 0) {
-+ /* Save gpwrdn register for further usage if stschng interrupt */
-+ core_if->gr_backup->gpwrdn_local =
-+ DWC_READ_REG32(&core_if->core_global_regs->gpwrdn);
-+ /*Exit from ISR and wait for stschng interrupt with bsessvld = 1 */
-+ return 1;
-+ }
-+
-+ /* Switch on the voltage to the core */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnswtch = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ dwc_udelay(10);
-+
-+ /* Reset the core */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnrstn = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ dwc_udelay(10);
-+
-+ /* Disable power clamps */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnclmp = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+
-+ /* Remove reset the core signal */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnrstn = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32);
-+ dwc_udelay(10);
-+
-+ /* Disable PMU interrupt */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuintsel = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ dwc_udelay(10);
-+
-+ /*Indicates that we are exiting from hibernation */
-+ core_if->hibernation_suspend = 0;
-+
-+ /* Disable PMU */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuactv = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ dwc_udelay(10);
-+
-+ core_if->op_state = B_PERIPHERAL;
-+ dwc_otg_core_init(core_if);
-+ dwc_otg_enable_global_interrupts(core_if);
-+ cil_pcd_start(core_if);
-+
-+ if (otg_cap_param == DWC_OTG_CAP_PARAM_HNP_SRP_CAPABLE ||
-+ otg_cap_param == DWC_OTG_CAP_PARAM_SRP_ONLY_CAPABLE) {
-+ /*
-+ * Initiate SRP after initial ADP probe.
-+ */
-+ dwc_otg_initiate_srp(core_if);
-+ }
-+ }
-+
-+ return 1;
-+}
-+/**
-+ * This interrupt indicates that the Wakeup Logic has detected a
-+ * status change either on IDDIG or BSessVld.
-+ */
-+static uint32_t dwc_otg_handle_pwrdn_stschng_intr(dwc_otg_device_t *otg_dev)
-+{
-+ int retval;
-+ gpwrdn_data_t gpwrdn = {.d32 = 0 };
-+ gpwrdn_data_t gpwrdn_temp = {.d32 = 0 };
-+ dwc_otg_core_if_t *core_if = otg_dev->core_if;
-+
-+ DWC_PRINTF("%s called\n", __FUNCTION__);
-+
-+ if (core_if->power_down == 2) {
-+ if (core_if->hibernation_suspend <= 0) {
-+ DWC_PRINTF("Already exited from Hibernation\n");
-+ return 1;
-+ } else
-+ gpwrdn_temp.d32 = core_if->gr_backup->gpwrdn_local;
-+
-+ } else {
-+ gpwrdn_temp.d32 = core_if->adp.gpwrdn;
-+ }
-+
-+ gpwrdn.d32 = DWC_READ_REG32(&core_if->core_global_regs->gpwrdn);
-+
-+ if (gpwrdn.b.idsts ^ gpwrdn_temp.b.idsts) {
-+ retval = dwc_otg_handle_pwrdn_idsts_change(otg_dev);
-+ } else if (gpwrdn.b.bsessvld ^ gpwrdn_temp.b.bsessvld) {
-+ retval = dwc_otg_handle_pwrdn_session_change(core_if);
-+ }
-+
-+ return retval;
-+}
-+
-+/**
-+ * This interrupt indicates that the Wakeup Logic has detected a
-+ * SRP.
-+ */
-+static int32_t dwc_otg_handle_pwrdn_srp_intr(dwc_otg_core_if_t * core_if)
-+{
-+ gpwrdn_data_t gpwrdn = {.d32 = 0 };
-+
-+ DWC_PRINTF("%s called\n", __FUNCTION__);
-+
-+ if (!core_if->hibernation_suspend) {
-+ DWC_PRINTF("Already exited from Hibernation\n");
-+ return 1;
-+ }
-+#ifdef DWC_DEV_SRPCAP
-+ if (core_if->pwron_timer_started) {
-+ core_if->pwron_timer_started = 0;
-+ DWC_TIMER_CANCEL(core_if->pwron_timer);
-+ }
-+#endif
-+
-+ /* Switch on the voltage to the core */
-+ gpwrdn.b.pwrdnswtch = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ dwc_udelay(10);
-+
-+ /* Reset the core */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnrstn = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ dwc_udelay(10);
-+
-+ /* Disable power clamps */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnclmp = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+
-+ /* Remove reset the core signal */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnrstn = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32);
-+ dwc_udelay(10);
-+
-+ /* Disable PMU interrupt */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuintsel = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+
-+ /* Indicates that we are exiting from hibernation */
-+ core_if->hibernation_suspend = 0;
-+
-+ /* Disable PMU */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuactv = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ dwc_udelay(10);
-+
-+ /* Programm Disable VBUS to 0 */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.dis_vbus = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+
-+ /*Initialize the core as Host */
-+ core_if->op_state = A_HOST;
-+ dwc_otg_core_init(core_if);
-+ dwc_otg_enable_global_interrupts(core_if);
-+ cil_hcd_start(core_if);
-+
-+ return 1;
-+}
-+
-+/** This interrupt indicates that restore command after Hibernation
-+ * was completed by the core. */
-+int32_t dwc_otg_handle_restore_done_intr(dwc_otg_core_if_t * core_if)
-+{
-+ pcgcctl_data_t pcgcctl;
-+ DWC_DEBUGPL(DBG_ANY, "++Restore Done Interrupt++\n");
-+
-+ //TODO De-assert restore signal. 8.a
-+ pcgcctl.d32 = DWC_READ_REG32(core_if->pcgcctl);
-+ if (pcgcctl.b.restoremode == 1) {
-+ gintmsk_data_t gintmsk = {.d32 = 0 };
-+ /*
-+ * If restore mode is Remote Wakeup,
-+ * unmask Remote Wakeup interrupt.
-+ */
-+ gintmsk.b.wkupintr = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gintmsk,
-+ 0, gintmsk.d32);
-+ }
-+
-+ return 1;
-+}
-+
-+/**
-+ * This interrupt indicates that a device has been disconnected from
-+ * the root port.
-+ */
-+int32_t dwc_otg_handle_disconnect_intr(dwc_otg_core_if_t * core_if)
-+{
-+ gintsts_data_t gintsts;
-+
-+ DWC_DEBUGPL(DBG_ANY, "++Disconnect Detected Interrupt++ (%s) %s\n",
-+ (dwc_otg_is_host_mode(core_if) ? "Host" : "Device"),
-+ op_state_str(core_if));
-+
-+/** @todo Consolidate this if statement. */
-+#ifndef DWC_HOST_ONLY
-+ if (core_if->op_state == B_HOST) {
-+ /* If in device mode Disconnect and stop the HCD, then
-+ * start the PCD. */
-+ DWC_SPINUNLOCK(core_if->lock);
-+ cil_hcd_disconnect(core_if);
-+ cil_pcd_start(core_if);
-+ DWC_SPINLOCK(core_if->lock);
-+ core_if->op_state = B_PERIPHERAL;
-+ } else if (dwc_otg_is_device_mode(core_if)) {
-+ gotgctl_data_t gotgctl = {.d32 = 0 };
-+ gotgctl.d32 =
-+ DWC_READ_REG32(&core_if->core_global_regs->gotgctl);
-+ if (gotgctl.b.hstsethnpen == 1) {
-+ /* Do nothing, if HNP in process the OTG
-+ * interrupt "Host Negotiation Detected"
-+ * interrupt will do the mode switch.
-+ */
-+ } else if (gotgctl.b.devhnpen == 0) {
-+ /* If in device mode Disconnect and stop the HCD, then
-+ * start the PCD. */
-+ DWC_SPINUNLOCK(core_if->lock);
-+ cil_hcd_disconnect(core_if);
-+ cil_pcd_start(core_if);
-+ DWC_SPINLOCK(core_if->lock);
-+ core_if->op_state = B_PERIPHERAL;
-+ } else {
-+ DWC_DEBUGPL(DBG_ANY, "!a_peripheral && !devhnpen\n");
-+ }
-+ } else {
-+ if (core_if->op_state == A_HOST) {
-+ /* A-Cable still connected but device disconnected. */
-+ cil_hcd_disconnect(core_if);
-+ if (core_if->adp_enable) {
-+ gpwrdn_data_t gpwrdn = { .d32 = 0 };
-+ cil_hcd_stop(core_if);
-+ /* Enable Power Down Logic */
-+ gpwrdn.b.pmuintsel = 1;
-+ gpwrdn.b.pmuactv = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->
-+ gpwrdn, 0, gpwrdn.d32);
-+ dwc_otg_adp_probe_start(core_if);
-+
-+ /* Power off the core */
-+ if (core_if->power_down == 2) {
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnswtch = 1;
-+ DWC_MODIFY_REG32
-+ (&core_if->core_global_regs->gpwrdn,
-+ gpwrdn.d32, 0);
-+ }
-+ }
-+ }
-+ }
-+#endif
-+ /* Change to L3(OFF) state */
-+ core_if->lx_state = DWC_OTG_L3;
-+
-+ gintsts.d32 = 0;
-+ gintsts.b.disconnect = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32);
-+ return 1;
-+}
-+
-+/**
-+ * This interrupt indicates that SUSPEND state has been detected on
-+ * the USB.
-+ *
-+ * For HNP the USB Suspend interrupt signals the change from
-+ * "a_peripheral" to "a_host".
-+ *
-+ * When power management is enabled the core will be put in low power
-+ * mode.
-+ */
-+int32_t dwc_otg_handle_usb_suspend_intr(dwc_otg_core_if_t * core_if)
-+{
-+ dsts_data_t dsts;
-+ gintsts_data_t gintsts;
-+ dcfg_data_t dcfg;
-+
-+ DWC_DEBUGPL(DBG_ANY, "USB SUSPEND\n");
-+
-+ if (dwc_otg_is_device_mode(core_if)) {
-+ /* Check the Device status register to determine if the Suspend
-+ * state is active. */
-+ dsts.d32 =
-+ DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dsts);
-+ DWC_DEBUGPL(DBG_PCD, "DSTS=0x%0x\n", dsts.d32);
-+ DWC_DEBUGPL(DBG_PCD, "DSTS.Suspend Status=%d "
-+ "HWCFG4.power Optimize=%d\n",
-+ dsts.b.suspsts, core_if->hwcfg4.b.power_optimiz);
-+
-+#ifdef PARTIAL_POWER_DOWN
-+/** @todo Add a module parameter for power management. */
-+
-+ if (dsts.b.suspsts && core_if->hwcfg4.b.power_optimiz) {
-+ pcgcctl_data_t power = {.d32 = 0 };
-+ DWC_DEBUGPL(DBG_CIL, "suspend\n");
-+
-+ power.b.pwrclmp = 1;
-+ DWC_WRITE_REG32(core_if->pcgcctl, power.d32);
-+
-+ power.b.rstpdwnmodule = 1;
-+ DWC_MODIFY_REG32(core_if->pcgcctl, 0, power.d32);
-+
-+ power.b.stoppclk = 1;
-+ DWC_MODIFY_REG32(core_if->pcgcctl, 0, power.d32);
-+
-+ } else {
-+ DWC_DEBUGPL(DBG_ANY, "disconnect?\n");
-+ }
-+#endif
-+ /* PCD callback for suspend. Release the lock inside of callback function */
-+ cil_pcd_suspend(core_if);
-+ if (core_if->power_down == 2)
-+ {
-+ dcfg.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dcfg);
-+ DWC_DEBUGPL(DBG_ANY,"lx_state = %08x\n",core_if->lx_state);
-+ DWC_DEBUGPL(DBG_ANY," device address = %08d\n",dcfg.b.devaddr);
-+
-+ if (core_if->lx_state != DWC_OTG_L3 && dcfg.b.devaddr) {
-+ pcgcctl_data_t pcgcctl = {.d32 = 0 };
-+ gpwrdn_data_t gpwrdn = {.d32 = 0 };
-+ gusbcfg_data_t gusbcfg = {.d32 = 0 };
-+
-+ /* Change to L2(suspend) state */
-+ core_if->lx_state = DWC_OTG_L2;
-+
-+ /* Clear interrupt in gintsts */
-+ gintsts.d32 = 0;
-+ gintsts.b.usbsuspend = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->
-+ gintsts, gintsts.d32);
-+ DWC_PRINTF("Start of hibernation completed\n");
-+ dwc_otg_save_global_regs(core_if);
-+ dwc_otg_save_dev_regs(core_if);
-+
-+ gusbcfg.d32 =
-+ DWC_READ_REG32(&core_if->core_global_regs->
-+ gusbcfg);
-+ if (gusbcfg.b.ulpi_utmi_sel == 1) {
-+ /* ULPI interface */
-+ /* Suspend the Phy Clock */
-+ pcgcctl.d32 = 0;
-+ pcgcctl.b.stoppclk = 1;
-+ DWC_MODIFY_REG32(core_if->pcgcctl, 0,
-+ pcgcctl.d32);
-+ dwc_udelay(10);
-+ gpwrdn.b.pmuactv = 1;
-+ DWC_MODIFY_REG32(&core_if->
-+ core_global_regs->
-+ gpwrdn, 0, gpwrdn.d32);
-+ } else {
-+ /* UTMI+ Interface */
-+ gpwrdn.b.pmuactv = 1;
-+ DWC_MODIFY_REG32(&core_if->
-+ core_global_regs->
-+ gpwrdn, 0, gpwrdn.d32);
-+ dwc_udelay(10);
-+ pcgcctl.b.stoppclk = 1;
-+ DWC_MODIFY_REG32(core_if->pcgcctl, 0,
-+ pcgcctl.d32);
-+ dwc_udelay(10);
-+ }
-+
-+ /* Set flag to indicate that we are in hibernation */
-+ core_if->hibernation_suspend = 1;
-+ /* Enable interrupts from wake up logic */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuintsel = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->
-+ gpwrdn, 0, gpwrdn.d32);
-+ dwc_udelay(10);
-+
-+ /* Unmask device mode interrupts in GPWRDN */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.rst_det_msk = 1;
-+ gpwrdn.b.lnstchng_msk = 1;
-+ gpwrdn.b.sts_chngint_msk = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->
-+ gpwrdn, 0, gpwrdn.d32);
-+ dwc_udelay(10);
-+
-+ /* Enable Power Down Clamp */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnclmp = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->
-+ gpwrdn, 0, gpwrdn.d32);
-+ dwc_udelay(10);
-+
-+ /* Switch off VDD */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnswtch = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->
-+ gpwrdn, 0, gpwrdn.d32);
-+
-+ /* Save gpwrdn register for further usage if stschng interrupt */
-+ core_if->gr_backup->gpwrdn_local =
-+ DWC_READ_REG32(&core_if->core_global_regs->gpwrdn);
-+ DWC_PRINTF("Hibernation completed\n");
-+
-+ return 1;
-+ }
-+ } else if (core_if->power_down == 3) {
-+ pcgcctl_data_t pcgcctl = {.d32 = 0 };
-+ dcfg.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dcfg);
-+ DWC_DEBUGPL(DBG_ANY, "lx_state = %08x\n",core_if->lx_state);
-+ DWC_DEBUGPL(DBG_ANY, " device address = %08d\n",dcfg.b.devaddr);
-+
-+ if (core_if->lx_state != DWC_OTG_L3 && dcfg.b.devaddr) {
-+ DWC_DEBUGPL(DBG_ANY, "Start entering to extended hibernation\n");
-+ core_if->xhib = 1;
-+
-+ /* Clear interrupt in gintsts */
-+ gintsts.d32 = 0;
-+ gintsts.b.usbsuspend = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->
-+ gintsts, gintsts.d32);
-+
-+ dwc_otg_save_global_regs(core_if);
-+ dwc_otg_save_dev_regs(core_if);
-+
-+ /* Wait for 10 PHY clocks */
-+ dwc_udelay(10);
-+
-+ /* Program GPIO register while entering to xHib */
-+ DWC_WRITE_REG32(&core_if->core_global_regs->ggpio, 0x1);
-+
-+ pcgcctl.b.enbl_extnd_hiber = 1;
-+ DWC_MODIFY_REG32(core_if->pcgcctl, 0, pcgcctl.d32);
-+ DWC_MODIFY_REG32(core_if->pcgcctl, 0, pcgcctl.d32);
-+
-+ pcgcctl.d32 = 0;
-+ pcgcctl.b.extnd_hiber_pwrclmp = 1;
-+ DWC_MODIFY_REG32(core_if->pcgcctl, 0, pcgcctl.d32);
-+
-+ pcgcctl.d32 = 0;
-+ pcgcctl.b.extnd_hiber_switch = 1;
-+ core_if->gr_backup->xhib_gpwrdn = DWC_READ_REG32(&core_if->core_global_regs->gpwrdn);
-+ core_if->gr_backup->xhib_pcgcctl = DWC_READ_REG32(core_if->pcgcctl) | pcgcctl.d32;
-+ DWC_MODIFY_REG32(core_if->pcgcctl, 0, pcgcctl.d32);
-+
-+ DWC_DEBUGPL(DBG_ANY, "Finished entering to extended hibernation\n");
-+
-+ return 1;
-+ }
-+ }
-+ } else {
-+ if (core_if->op_state == A_PERIPHERAL) {
-+ DWC_DEBUGPL(DBG_ANY, "a_peripheral->a_host\n");
-+ /* Clear the a_peripheral flag, back to a_host. */
-+ DWC_SPINUNLOCK(core_if->lock);
-+ cil_pcd_stop(core_if);
-+ cil_hcd_start(core_if);
-+ DWC_SPINLOCK(core_if->lock);
-+ core_if->op_state = A_HOST;
-+ }
-+ }
-+
-+ /* Change to L2(suspend) state */
-+ core_if->lx_state = DWC_OTG_L2;
-+
-+ /* Clear interrupt */
-+ gintsts.d32 = 0;
-+ gintsts.b.usbsuspend = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32);
-+
-+ return 1;
-+}
-+
-+static int32_t dwc_otg_handle_xhib_exit_intr(dwc_otg_core_if_t * core_if)
-+{
-+ gpwrdn_data_t gpwrdn = {.d32 = 0 };
-+ pcgcctl_data_t pcgcctl = {.d32 = 0 };
-+ gahbcfg_data_t gahbcfg = {.d32 = 0 };
-+
-+ dwc_udelay(10);
-+
-+ /* Program GPIO register while entering to xHib */
-+ DWC_WRITE_REG32(&core_if->core_global_regs->ggpio, 0x0);
-+
-+ pcgcctl.d32 = core_if->gr_backup->xhib_pcgcctl;
-+ pcgcctl.b.extnd_hiber_pwrclmp = 0;
-+ DWC_WRITE_REG32(core_if->pcgcctl, pcgcctl.d32);
-+ dwc_udelay(10);
-+
-+ gpwrdn.d32 = core_if->gr_backup->xhib_gpwrdn;
-+ gpwrdn.b.restore = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32);
-+ dwc_udelay(10);
-+
-+ restore_lpm_i2c_regs(core_if);
-+
-+ pcgcctl.d32 = core_if->gr_backup->pcgcctl_local & (0x3FFFF << 14);
-+ pcgcctl.b.max_xcvrselect = 1;
-+ pcgcctl.b.ess_reg_restored = 0;
-+ pcgcctl.b.extnd_hiber_switch = 0;
-+ pcgcctl.b.extnd_hiber_pwrclmp = 0;
-+ pcgcctl.b.enbl_extnd_hiber = 1;
-+ DWC_WRITE_REG32(core_if->pcgcctl, pcgcctl.d32);
-+
-+ gahbcfg.d32 = core_if->gr_backup->gahbcfg_local;
-+ gahbcfg.b.glblintrmsk = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gahbcfg, gahbcfg.d32);
-+
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, 0xFFFFFFFF);
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintmsk, 0x1 << 16);
-+
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gusbcfg,
-+ core_if->gr_backup->gusbcfg_local);
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dcfg,
-+ core_if->dr_backup->dcfg);
-+
-+ pcgcctl.d32 = 0;
-+ pcgcctl.d32 = core_if->gr_backup->pcgcctl_local & (0x3FFFF << 14);
-+ pcgcctl.b.max_xcvrselect = 1;
-+ pcgcctl.d32 |= 0x608;
-+ DWC_WRITE_REG32(core_if->pcgcctl, pcgcctl.d32);
-+ dwc_udelay(10);
-+
-+ pcgcctl.d32 = 0;
-+ pcgcctl.d32 = core_if->gr_backup->pcgcctl_local & (0x3FFFF << 14);
-+ pcgcctl.b.max_xcvrselect = 1;
-+ pcgcctl.b.ess_reg_restored = 1;
-+ pcgcctl.b.enbl_extnd_hiber = 1;
-+ pcgcctl.b.rstpdwnmodule = 1;
-+ pcgcctl.b.restoremode = 1;
-+ DWC_WRITE_REG32(core_if->pcgcctl, pcgcctl.d32);
-+
-+ DWC_DEBUGPL(DBG_ANY, "%s called\n", __FUNCTION__);
-+
-+ return 1;
-+}
-+
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+/**
-+ * This function hadles LPM transaction received interrupt.
-+ */
-+static int32_t dwc_otg_handle_lpm_intr(dwc_otg_core_if_t * core_if)
-+{
-+ glpmcfg_data_t lpmcfg;
-+ gintsts_data_t gintsts;
-+
-+ if (!core_if->core_params->lpm_enable) {
-+ DWC_PRINTF("Unexpected LPM interrupt\n");
-+ }
-+
-+ lpmcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg);
-+ DWC_PRINTF("LPM config register = 0x%08x\n", lpmcfg.d32);
-+
-+ if (dwc_otg_is_host_mode(core_if)) {
-+ cil_hcd_sleep(core_if);
-+ } else {
-+ lpmcfg.b.hird_thres |= (1 << 4);
-+ DWC_WRITE_REG32(&core_if->core_global_regs->glpmcfg,
-+ lpmcfg.d32);
-+ }
-+
-+ /* Examine prt_sleep_sts after TL1TokenTetry period max (10 us) */
-+ dwc_udelay(10);
-+ lpmcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg);
-+ if (lpmcfg.b.prt_sleep_sts) {
-+ /* Save the current state */
-+ core_if->lx_state = DWC_OTG_L1;
-+ }
-+
-+ /* Clear interrupt */
-+ gintsts.d32 = 0;
-+ gintsts.b.lpmtranrcvd = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32);
-+ return 1;
-+}
-+#endif /* CONFIG_USB_DWC_OTG_LPM */
-+
-+/**
-+ * This function returns the Core Interrupt register.
-+ */
-+static inline uint32_t dwc_otg_read_common_intr(dwc_otg_core_if_t * core_if, gintmsk_data_t *reenable_gintmsk, dwc_otg_hcd_t *hcd)
-+{
-+ gahbcfg_data_t gahbcfg = {.d32 = 0 };
-+ gintsts_data_t gintsts;
-+ gintmsk_data_t gintmsk;
-+ gintmsk_data_t gintmsk_common = {.d32 = 0 };
-+ gintmsk_common.b.wkupintr = 1;
-+ gintmsk_common.b.sessreqintr = 1;
-+ gintmsk_common.b.conidstschng = 1;
-+ gintmsk_common.b.otgintr = 1;
-+ gintmsk_common.b.modemismatch = 1;
-+ gintmsk_common.b.disconnect = 1;
-+ gintmsk_common.b.usbsuspend = 1;
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+ gintmsk_common.b.lpmtranrcvd = 1;
-+#endif
-+ gintmsk_common.b.restoredone = 1;
-+ if(dwc_otg_is_device_mode(core_if))
-+ {
-+ /** @todo: The port interrupt occurs while in device
-+ * mode. Added code to CIL to clear the interrupt for now!
-+ */
-+ gintmsk_common.b.portintr = 1;
-+ }
-+ gintsts.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintsts);
-+ gintmsk.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintmsk);
-+ if(fiq_enable) {
-+ local_fiq_disable();
-+ /* Pull in the interrupts that the FIQ has masked */
-+ gintmsk.d32 |= ~(hcd->fiq_state->gintmsk_saved.d32);
-+ gintmsk.d32 |= gintmsk_common.d32;
-+ /* for the upstairs function to reenable - have to read it here in case FIQ triggers again */
-+ reenable_gintmsk->d32 = gintmsk.d32;
-+ local_fiq_enable();
-+ }
-+
-+ gahbcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->gahbcfg);
-+
-+#ifdef DEBUG
-+ /* if any common interrupts set */
-+ if (gintsts.d32 & gintmsk_common.d32) {
-+ DWC_DEBUGPL(DBG_ANY, "common_intr: gintsts=%08x gintmsk=%08x\n",
-+ gintsts.d32, gintmsk.d32);
-+ }
-+#endif
-+ if (!fiq_enable){
-+ if (gahbcfg.b.glblintrmsk)
-+ return ((gintsts.d32 & gintmsk.d32) & gintmsk_common.d32);
-+ else
-+ return 0;
-+ } else {
-+ /* Our IRQ kicker is no longer the USB hardware, it's the MPHI interface.
-+ * Can't trust the global interrupt mask bit in this case.
-+ */
-+ return ((gintsts.d32 & gintmsk.d32) & gintmsk_common.d32);
-+ }
-+
-+}
-+
-+/* MACRO for clearing interupt bits in GPWRDN register */
-+#define CLEAR_GPWRDN_INTR(__core_if,__intr) \
-+do { \
-+ gpwrdn_data_t gpwrdn = {.d32=0}; \
-+ gpwrdn.b.__intr = 1; \
-+ DWC_MODIFY_REG32(&__core_if->core_global_regs->gpwrdn, \
-+ 0, gpwrdn.d32); \
-+} while (0)
-+
-+/**
-+ * Common interrupt handler.
-+ *
-+ * The common interrupts are those that occur in both Host and Device mode.
-+ * This handler handles the following interrupts:
-+ * - Mode Mismatch Interrupt
-+ * - Disconnect Interrupt
-+ * - OTG Interrupt
-+ * - Connector ID Status Change Interrupt
-+ * - Session Request Interrupt.
-+ * - Resume / Remote Wakeup Detected Interrupt.
-+ * - LPM Transaction Received Interrupt
-+ * - ADP Transaction Received Interrupt
-+ *
-+ */
-+int32_t dwc_otg_handle_common_intr(void *dev)
-+{
-+ int retval = 0;
-+ gintsts_data_t gintsts;
-+ gintmsk_data_t gintmsk_reenable = { .d32 = 0 };
-+ gpwrdn_data_t gpwrdn = {.d32 = 0 };
-+ dwc_otg_device_t *otg_dev = dev;
-+ dwc_otg_core_if_t *core_if = otg_dev->core_if;
-+ gpwrdn.d32 = DWC_READ_REG32(&core_if->core_global_regs->gpwrdn);
-+ if (dwc_otg_is_device_mode(core_if))
-+ core_if->frame_num = dwc_otg_get_frame_number(core_if);
-+
-+ if (core_if->lock)
-+ DWC_SPINLOCK(core_if->lock);
-+
-+ if (core_if->power_down == 3 && core_if->xhib == 1) {
-+ DWC_DEBUGPL(DBG_ANY, "Exiting from xHIB state\n");
-+ retval |= dwc_otg_handle_xhib_exit_intr(core_if);
-+ core_if->xhib = 2;
-+ if (core_if->lock)
-+ DWC_SPINUNLOCK(core_if->lock);
-+
-+ return retval;
-+ }
-+
-+ if (core_if->hibernation_suspend <= 0) {
-+ /* read_common will have to poke the FIQ's saved mask. We must then clear this mask at the end
-+ * of this handler - god only knows why it's done like this
-+ */
-+ gintsts.d32 = dwc_otg_read_common_intr(core_if, &gintmsk_reenable, otg_dev->hcd);
-+
-+ if (gintsts.b.modemismatch) {
-+ retval |= dwc_otg_handle_mode_mismatch_intr(core_if);
-+ }
-+ if (gintsts.b.otgintr) {
-+ retval |= dwc_otg_handle_otg_intr(core_if);
-+ }
-+ if (gintsts.b.conidstschng) {
-+ retval |=
-+ dwc_otg_handle_conn_id_status_change_intr(core_if);
-+ }
-+ if (gintsts.b.disconnect) {
-+ retval |= dwc_otg_handle_disconnect_intr(core_if);
-+ }
-+ if (gintsts.b.sessreqintr) {
-+ retval |= dwc_otg_handle_session_req_intr(core_if);
-+ }
-+ if (gintsts.b.wkupintr) {
-+ retval |= dwc_otg_handle_wakeup_detected_intr(core_if);
-+ }
-+ if (gintsts.b.usbsuspend) {
-+ retval |= dwc_otg_handle_usb_suspend_intr(core_if);
-+ }
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+ if (gintsts.b.lpmtranrcvd) {
-+ retval |= dwc_otg_handle_lpm_intr(core_if);
-+ }
-+#endif
-+ if (gintsts.b.restoredone) {
-+ gintsts.d32 = 0;
-+ if (core_if->power_down == 2)
-+ core_if->hibernation_suspend = -1;
-+ else if (core_if->power_down == 3 && core_if->xhib == 2) {
-+ gpwrdn_data_t gpwrdn = {.d32 = 0 };
-+ pcgcctl_data_t pcgcctl = {.d32 = 0 };
-+ dctl_data_t dctl = {.d32 = 0 };
-+
-+ DWC_WRITE_REG32(&core_if->core_global_regs->
-+ gintsts, 0xFFFFFFFF);
-+
-+ DWC_DEBUGPL(DBG_ANY,
-+ "RESTORE DONE generated\n");
-+
-+ gpwrdn.b.restore = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ dwc_udelay(10);
-+
-+ pcgcctl.b.rstpdwnmodule = 1;
-+ DWC_MODIFY_REG32(core_if->pcgcctl, pcgcctl.d32, 0);
-+
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gusbcfg, core_if->gr_backup->gusbcfg_local);
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dcfg, core_if->dr_backup->dcfg);
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dctl, core_if->dr_backup->dctl);
-+ dwc_udelay(50);
-+
-+ dctl.b.pwronprgdone = 1;
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl, 0, dctl.d32);
-+ dwc_udelay(10);
-+
-+ dwc_otg_restore_global_regs(core_if);
-+ dwc_otg_restore_dev_regs(core_if, 0);
-+
-+ dctl.d32 = 0;
-+ dctl.b.pwronprgdone = 1;
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl, dctl.d32, 0);
-+ dwc_udelay(10);
-+
-+ pcgcctl.d32 = 0;
-+ pcgcctl.b.enbl_extnd_hiber = 1;
-+ DWC_MODIFY_REG32(core_if->pcgcctl, pcgcctl.d32, 0);
-+
-+ /* The core will be in ON STATE */
-+ core_if->lx_state = DWC_OTG_L0;
-+ core_if->xhib = 0;
-+
-+ DWC_SPINUNLOCK(core_if->lock);
-+ if (core_if->pcd_cb && core_if->pcd_cb->resume_wakeup) {
-+ core_if->pcd_cb->resume_wakeup(core_if->pcd_cb->p);
-+ }
-+ DWC_SPINLOCK(core_if->lock);
-+
-+ }
-+
-+ gintsts.b.restoredone = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts,gintsts.d32);
-+ DWC_PRINTF(" --Restore done interrupt received-- \n");
-+ retval |= 1;
-+ }
-+ if (gintsts.b.portintr && dwc_otg_is_device_mode(core_if)) {
-+ /* The port interrupt occurs while in device mode with HPRT0
-+ * Port Enable/Disable.
-+ */
-+ gintsts.d32 = 0;
-+ gintsts.b.portintr = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts,gintsts.d32);
-+ retval |= 1;
-+ gintmsk_reenable.b.portintr = 1;
-+
-+ }
-+ /* Did we actually handle anything? if so, unmask the interrupt */
-+// fiq_print(FIQDBG_INT, otg_dev->hcd->fiq_state, "CILOUT %1d", retval);
-+// fiq_print(FIQDBG_INT, otg_dev->hcd->fiq_state, "%08x", gintsts.d32);
-+// fiq_print(FIQDBG_INT, otg_dev->hcd->fiq_state, "%08x", gintmsk_reenable.d32);
-+ if (retval && fiq_enable) {
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintmsk, gintmsk_reenable.d32);
-+ }
-+
-+ } else {
-+ DWC_DEBUGPL(DBG_ANY, "gpwrdn=%08x\n", gpwrdn.d32);
-+
-+ if (gpwrdn.b.disconn_det && gpwrdn.b.disconn_det_msk) {
-+ CLEAR_GPWRDN_INTR(core_if, disconn_det);
-+ if (gpwrdn.b.linestate == 0) {
-+ dwc_otg_handle_pwrdn_disconnect_intr(core_if);
-+ } else {
-+ DWC_PRINTF("Disconnect detected while linestate is not 0\n");
-+ }
-+
-+ retval |= 1;
-+ }
-+ if (gpwrdn.b.lnstschng && gpwrdn.b.lnstchng_msk) {
-+ CLEAR_GPWRDN_INTR(core_if, lnstschng);
-+ /* remote wakeup from hibernation */
-+ if (gpwrdn.b.linestate == 2 || gpwrdn.b.linestate == 1) {
-+ dwc_otg_handle_pwrdn_wakeup_detected_intr(core_if);
-+ } else {
-+ DWC_PRINTF("gpwrdn.linestate = %d\n", gpwrdn.b.linestate);
-+ }
-+ retval |= 1;
-+ }
-+ if (gpwrdn.b.rst_det && gpwrdn.b.rst_det_msk) {
-+ CLEAR_GPWRDN_INTR(core_if, rst_det);
-+ if (gpwrdn.b.linestate == 0) {
-+ DWC_PRINTF("Reset detected\n");
-+ retval |= dwc_otg_device_hibernation_restore(core_if, 0, 1);
-+ }
-+ }
-+ if (gpwrdn.b.srp_det && gpwrdn.b.srp_det_msk) {
-+ CLEAR_GPWRDN_INTR(core_if, srp_det);
-+ dwc_otg_handle_pwrdn_srp_intr(core_if);
-+ retval |= 1;
-+ }
-+ }
-+ /* Handle ADP interrupt here */
-+ if (gpwrdn.b.adp_int) {
-+ DWC_PRINTF("ADP interrupt\n");
-+ CLEAR_GPWRDN_INTR(core_if, adp_int);
-+ dwc_otg_adp_handle_intr(core_if);
-+ retval |= 1;
-+ }
-+ if (gpwrdn.b.sts_chngint && gpwrdn.b.sts_chngint_msk) {
-+ DWC_PRINTF("STS CHNG interrupt asserted\n");
-+ CLEAR_GPWRDN_INTR(core_if, sts_chngint);
-+ dwc_otg_handle_pwrdn_stschng_intr(otg_dev);
-+
-+ retval |= 1;
-+ }
-+ if (core_if->lock)
-+ DWC_SPINUNLOCK(core_if->lock);
-+ return retval;
-+}
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_core_if.h
-@@ -0,0 +1,705 @@
-+/* ==========================================================================
-+ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_core_if.h $
-+ * $Revision: #13 $
-+ * $Date: 2012/08/10 $
-+ * $Change: 2047372 $
-+ *
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+#if !defined(__DWC_CORE_IF_H__)
-+#define __DWC_CORE_IF_H__
-+
-+#include "dwc_os.h"
-+
-+/** @file
-+ * This file defines DWC_OTG Core API
-+ */
-+
-+struct dwc_otg_core_if;
-+typedef struct dwc_otg_core_if dwc_otg_core_if_t;
-+
-+/** Maximum number of Periodic FIFOs */
-+#define MAX_PERIO_FIFOS 15
-+/** Maximum number of Periodic FIFOs */
-+#define MAX_TX_FIFOS 15
-+
-+/** Maximum number of Endpoints/HostChannels */
-+#define MAX_EPS_CHANNELS 16
-+
-+extern dwc_otg_core_if_t *dwc_otg_cil_init(const uint32_t * _reg_base_addr);
-+extern void dwc_otg_core_init(dwc_otg_core_if_t * _core_if);
-+extern void dwc_otg_cil_remove(dwc_otg_core_if_t * _core_if);
-+
-+extern void dwc_otg_enable_global_interrupts(dwc_otg_core_if_t * _core_if);
-+extern void dwc_otg_disable_global_interrupts(dwc_otg_core_if_t * _core_if);
-+
-+extern uint8_t dwc_otg_is_device_mode(dwc_otg_core_if_t * _core_if);
-+extern uint8_t dwc_otg_is_host_mode(dwc_otg_core_if_t * _core_if);
-+
-+extern uint8_t dwc_otg_is_dma_enable(dwc_otg_core_if_t * core_if);
-+
-+/** This function should be called on every hardware interrupt. */
-+extern int32_t dwc_otg_handle_common_intr(void *otg_dev);
-+
-+/** @name OTG Core Parameters */
-+/** @{ */
-+
-+/**
-+ * Specifies the OTG capabilities. The driver will automatically
-+ * detect the value for this parameter if none is specified.
-+ * 0 - HNP and SRP capable (default)
-+ * 1 - SRP Only capable
-+ * 2 - No HNP/SRP capable
-+ */
-+extern int dwc_otg_set_param_otg_cap(dwc_otg_core_if_t * core_if, int32_t val);
-+extern int32_t dwc_otg_get_param_otg_cap(dwc_otg_core_if_t * core_if);
-+#define DWC_OTG_CAP_PARAM_HNP_SRP_CAPABLE 0
-+#define DWC_OTG_CAP_PARAM_SRP_ONLY_CAPABLE 1
-+#define DWC_OTG_CAP_PARAM_NO_HNP_SRP_CAPABLE 2
-+#define dwc_param_otg_cap_default DWC_OTG_CAP_PARAM_HNP_SRP_CAPABLE
-+
-+extern int dwc_otg_set_param_opt(dwc_otg_core_if_t * core_if, int32_t val);
-+extern int32_t dwc_otg_get_param_opt(dwc_otg_core_if_t * core_if);
-+#define dwc_param_opt_default 1
-+
-+/**
-+ * Specifies whether to use slave or DMA mode for accessing the data
-+ * FIFOs. The driver will automatically detect the value for this
-+ * parameter if none is specified.
-+ * 0 - Slave
-+ * 1 - DMA (default, if available)
-+ */
-+extern int dwc_otg_set_param_dma_enable(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_dma_enable(dwc_otg_core_if_t * core_if);
-+#define dwc_param_dma_enable_default 1
-+
-+/**
-+ * When DMA mode is enabled specifies whether to use
-+ * address DMA or DMA Descritor mode for accessing the data
-+ * FIFOs in device mode. The driver will automatically detect
-+ * the value for this parameter if none is specified.
-+ * 0 - address DMA
-+ * 1 - DMA Descriptor(default, if available)
-+ */
-+extern int dwc_otg_set_param_dma_desc_enable(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_dma_desc_enable(dwc_otg_core_if_t * core_if);
-+//#define dwc_param_dma_desc_enable_default 1
-+#define dwc_param_dma_desc_enable_default 0 // Broadcom BCM2708
-+
-+/** The DMA Burst size (applicable only for External DMA
-+ * Mode). 1, 4, 8 16, 32, 64, 128, 256 (default 32)
-+ */
-+extern int dwc_otg_set_param_dma_burst_size(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_dma_burst_size(dwc_otg_core_if_t * core_if);
-+#define dwc_param_dma_burst_size_default 32
-+
-+/**
-+ * Specifies the maximum speed of operation in host and device mode.
-+ * The actual speed depends on the speed of the attached device and
-+ * the value of phy_type. The actual speed depends on the speed of the
-+ * attached device.
-+ * 0 - High Speed (default)
-+ * 1 - Full Speed
-+ */
-+extern int dwc_otg_set_param_speed(dwc_otg_core_if_t * core_if, int32_t val);
-+extern int32_t dwc_otg_get_param_speed(dwc_otg_core_if_t * core_if);
-+#define dwc_param_speed_default 0
-+#define DWC_SPEED_PARAM_HIGH 0
-+#define DWC_SPEED_PARAM_FULL 1
-+
-+/** Specifies whether low power mode is supported when attached
-+ * to a Full Speed or Low Speed device in host mode.
-+ * 0 - Don't support low power mode (default)
-+ * 1 - Support low power mode
-+ */
-+extern int dwc_otg_set_param_host_support_fs_ls_low_power(dwc_otg_core_if_t *
-+ core_if, int32_t val);
-+extern int32_t dwc_otg_get_param_host_support_fs_ls_low_power(dwc_otg_core_if_t
-+ * core_if);
-+#define dwc_param_host_support_fs_ls_low_power_default 0
-+
-+/** Specifies the PHY clock rate in low power mode when connected to a
-+ * Low Speed device in host mode. This parameter is applicable only if
-+ * HOST_SUPPORT_FS_LS_LOW_POWER is enabled. If PHY_TYPE is set to FS
-+ * then defaults to 6 MHZ otherwise 48 MHZ.
-+ *
-+ * 0 - 48 MHz
-+ * 1 - 6 MHz
-+ */
-+extern int dwc_otg_set_param_host_ls_low_power_phy_clk(dwc_otg_core_if_t *
-+ core_if, int32_t val);
-+extern int32_t dwc_otg_get_param_host_ls_low_power_phy_clk(dwc_otg_core_if_t *
-+ core_if);
-+#define dwc_param_host_ls_low_power_phy_clk_default 0
-+#define DWC_HOST_LS_LOW_POWER_PHY_CLK_PARAM_48MHZ 0
-+#define DWC_HOST_LS_LOW_POWER_PHY_CLK_PARAM_6MHZ 1
-+
-+/**
-+ * 0 - Use cC FIFO size parameters
-+ * 1 - Allow dynamic FIFO sizing (default)
-+ */
-+extern int dwc_otg_set_param_enable_dynamic_fifo(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_enable_dynamic_fifo(dwc_otg_core_if_t *
-+ core_if);
-+#define dwc_param_enable_dynamic_fifo_default 1
-+
-+/** Total number of 4-byte words in the data FIFO memory. This
-+ * memory includes the Rx FIFO, non-periodic Tx FIFO, and periodic
-+ * Tx FIFOs.
-+ * 32 to 32768 (default 8192)
-+ * Note: The total FIFO memory depth in the FPGA configuration is 8192.
-+ */
-+extern int dwc_otg_set_param_data_fifo_size(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_data_fifo_size(dwc_otg_core_if_t * core_if);
-+//#define dwc_param_data_fifo_size_default 8192
-+#define dwc_param_data_fifo_size_default 0xFF0 // Broadcom BCM2708
-+
-+/** Number of 4-byte words in the Rx FIFO in device mode when dynamic
-+ * FIFO sizing is enabled.
-+ * 16 to 32768 (default 1064)
-+ */
-+extern int dwc_otg_set_param_dev_rx_fifo_size(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_dev_rx_fifo_size(dwc_otg_core_if_t * core_if);
-+#define dwc_param_dev_rx_fifo_size_default 1064
-+
-+/** Number of 4-byte words in the non-periodic Tx FIFO in device mode
-+ * when dynamic FIFO sizing is enabled.
-+ * 16 to 32768 (default 1024)
-+ */
-+extern int dwc_otg_set_param_dev_nperio_tx_fifo_size(dwc_otg_core_if_t *
-+ core_if, int32_t val);
-+extern int32_t dwc_otg_get_param_dev_nperio_tx_fifo_size(dwc_otg_core_if_t *
-+ core_if);
-+#define dwc_param_dev_nperio_tx_fifo_size_default 1024
-+
-+/** Number of 4-byte words in each of the periodic Tx FIFOs in device
-+ * mode when dynamic FIFO sizing is enabled.
-+ * 4 to 768 (default 256)
-+ */
-+extern int dwc_otg_set_param_dev_perio_tx_fifo_size(dwc_otg_core_if_t * core_if,
-+ int32_t val, int fifo_num);
-+extern int32_t dwc_otg_get_param_dev_perio_tx_fifo_size(dwc_otg_core_if_t *
-+ core_if, int fifo_num);
-+#define dwc_param_dev_perio_tx_fifo_size_default 256
-+
-+/** Number of 4-byte words in the Rx FIFO in host mode when dynamic
-+ * FIFO sizing is enabled.
-+ * 16 to 32768 (default 1024)
-+ */
-+extern int dwc_otg_set_param_host_rx_fifo_size(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_host_rx_fifo_size(dwc_otg_core_if_t * core_if);
-+//#define dwc_param_host_rx_fifo_size_default 1024
-+#define dwc_param_host_rx_fifo_size_default 774 // Broadcom BCM2708
-+
-+/** Number of 4-byte words in the non-periodic Tx FIFO in host mode
-+ * when Dynamic FIFO sizing is enabled in the core.
-+ * 16 to 32768 (default 1024)
-+ */
-+extern int dwc_otg_set_param_host_nperio_tx_fifo_size(dwc_otg_core_if_t *
-+ core_if, int32_t val);
-+extern int32_t dwc_otg_get_param_host_nperio_tx_fifo_size(dwc_otg_core_if_t *
-+ core_if);
-+//#define dwc_param_host_nperio_tx_fifo_size_default 1024
-+#define dwc_param_host_nperio_tx_fifo_size_default 0x100 // Broadcom BCM2708
-+
-+/** Number of 4-byte words in the host periodic Tx FIFO when dynamic
-+ * FIFO sizing is enabled.
-+ * 16 to 32768 (default 1024)
-+ */
-+extern int dwc_otg_set_param_host_perio_tx_fifo_size(dwc_otg_core_if_t *
-+ core_if, int32_t val);
-+extern int32_t dwc_otg_get_param_host_perio_tx_fifo_size(dwc_otg_core_if_t *
-+ core_if);
-+//#define dwc_param_host_perio_tx_fifo_size_default 1024
-+#define dwc_param_host_perio_tx_fifo_size_default 0x200 // Broadcom BCM2708
-+
-+/** The maximum transfer size supported in bytes.
-+ * 2047 to 65,535 (default 65,535)
-+ */
-+extern int dwc_otg_set_param_max_transfer_size(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_max_transfer_size(dwc_otg_core_if_t * core_if);
-+#define dwc_param_max_transfer_size_default 65535
-+
-+/** The maximum number of packets in a transfer.
-+ * 15 to 511 (default 511)
-+ */
-+extern int dwc_otg_set_param_max_packet_count(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_max_packet_count(dwc_otg_core_if_t * core_if);
-+#define dwc_param_max_packet_count_default 511
-+
-+/** The number of host channel registers to use.
-+ * 1 to 16 (default 12)
-+ * Note: The FPGA configuration supports a maximum of 12 host channels.
-+ */
-+extern int dwc_otg_set_param_host_channels(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_host_channels(dwc_otg_core_if_t * core_if);
-+//#define dwc_param_host_channels_default 12
-+#define dwc_param_host_channels_default 8 // Broadcom BCM2708
-+
-+/** The number of endpoints in addition to EP0 available for device
-+ * mode operations.
-+ * 1 to 15 (default 6 IN and OUT)
-+ * Note: The FPGA configuration supports a maximum of 6 IN and OUT
-+ * endpoints in addition to EP0.
-+ */
-+extern int dwc_otg_set_param_dev_endpoints(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_dev_endpoints(dwc_otg_core_if_t * core_if);
-+#define dwc_param_dev_endpoints_default 6
-+
-+/**
-+ * Specifies the type of PHY interface to use. By default, the driver
-+ * will automatically detect the phy_type.
-+ *
-+ * 0 - Full Speed PHY
-+ * 1 - UTMI+ (default)
-+ * 2 - ULPI
-+ */
-+extern int dwc_otg_set_param_phy_type(dwc_otg_core_if_t * core_if, int32_t val);
-+extern int32_t dwc_otg_get_param_phy_type(dwc_otg_core_if_t * core_if);
-+#define DWC_PHY_TYPE_PARAM_FS 0
-+#define DWC_PHY_TYPE_PARAM_UTMI 1
-+#define DWC_PHY_TYPE_PARAM_ULPI 2
-+#define dwc_param_phy_type_default DWC_PHY_TYPE_PARAM_UTMI
-+
-+/**
-+ * Specifies the UTMI+ Data Width. This parameter is
-+ * applicable for a PHY_TYPE of UTMI+ or ULPI. (For a ULPI
-+ * PHY_TYPE, this parameter indicates the data width between
-+ * the MAC and the ULPI Wrapper.) Also, this parameter is
-+ * applicable only if the OTG_HSPHY_WIDTH cC parameter was set
-+ * to "8 and 16 bits", meaning that the core has been
-+ * configured to work at either data path width.
-+ *
-+ * 8 or 16 bits (default 16)
-+ */
-+extern int dwc_otg_set_param_phy_utmi_width(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_phy_utmi_width(dwc_otg_core_if_t * core_if);
-+//#define dwc_param_phy_utmi_width_default 16
-+#define dwc_param_phy_utmi_width_default 8 // Broadcom BCM2708
-+
-+/**
-+ * Specifies whether the ULPI operates at double or single
-+ * data rate. This parameter is only applicable if PHY_TYPE is
-+ * ULPI.
-+ *
-+ * 0 - single data rate ULPI interface with 8 bit wide data
-+ * bus (default)
-+ * 1 - double data rate ULPI interface with 4 bit wide data
-+ * bus
-+ */
-+extern int dwc_otg_set_param_phy_ulpi_ddr(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_phy_ulpi_ddr(dwc_otg_core_if_t * core_if);
-+#define dwc_param_phy_ulpi_ddr_default 0
-+
-+/**
-+ * Specifies whether to use the internal or external supply to
-+ * drive the vbus with a ULPI phy.
-+ */
-+extern int dwc_otg_set_param_phy_ulpi_ext_vbus(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_phy_ulpi_ext_vbus(dwc_otg_core_if_t * core_if);
-+#define DWC_PHY_ULPI_INTERNAL_VBUS 0
-+#define DWC_PHY_ULPI_EXTERNAL_VBUS 1
-+#define dwc_param_phy_ulpi_ext_vbus_default DWC_PHY_ULPI_INTERNAL_VBUS
-+
-+/**
-+ * Specifies whether to use the I2Cinterface for full speed PHY. This
-+ * parameter is only applicable if PHY_TYPE is FS.
-+ * 0 - No (default)
-+ * 1 - Yes
-+ */
-+extern int dwc_otg_set_param_i2c_enable(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_i2c_enable(dwc_otg_core_if_t * core_if);
-+#define dwc_param_i2c_enable_default 0
-+
-+extern int dwc_otg_set_param_ulpi_fs_ls(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_ulpi_fs_ls(dwc_otg_core_if_t * core_if);
-+#define dwc_param_ulpi_fs_ls_default 0
-+
-+extern int dwc_otg_set_param_ts_dline(dwc_otg_core_if_t * core_if, int32_t val);
-+extern int32_t dwc_otg_get_param_ts_dline(dwc_otg_core_if_t * core_if);
-+#define dwc_param_ts_dline_default 0
-+
-+/**
-+ * Specifies whether dedicated transmit FIFOs are
-+ * enabled for non periodic IN endpoints in device mode
-+ * 0 - No
-+ * 1 - Yes
-+ */
-+extern int dwc_otg_set_param_en_multiple_tx_fifo(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_en_multiple_tx_fifo(dwc_otg_core_if_t *
-+ core_if);
-+#define dwc_param_en_multiple_tx_fifo_default 1
-+
-+/** Number of 4-byte words in each of the Tx FIFOs in device
-+ * mode when dynamic FIFO sizing is enabled.
-+ * 4 to 768 (default 256)
-+ */
-+extern int dwc_otg_set_param_dev_tx_fifo_size(dwc_otg_core_if_t * core_if,
-+ int fifo_num, int32_t val);
-+extern int32_t dwc_otg_get_param_dev_tx_fifo_size(dwc_otg_core_if_t * core_if,
-+ int fifo_num);
-+#define dwc_param_dev_tx_fifo_size_default 768
-+
-+/** Thresholding enable flag-
-+ * bit 0 - enable non-ISO Tx thresholding
-+ * bit 1 - enable ISO Tx thresholding
-+ * bit 2 - enable Rx thresholding
-+ */
-+extern int dwc_otg_set_param_thr_ctl(dwc_otg_core_if_t * core_if, int32_t val);
-+extern int32_t dwc_otg_get_thr_ctl(dwc_otg_core_if_t * core_if, int fifo_num);
-+#define dwc_param_thr_ctl_default 0
-+
-+/** Thresholding length for Tx
-+ * FIFOs in 32 bit DWORDs
-+ */
-+extern int dwc_otg_set_param_tx_thr_length(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_tx_thr_length(dwc_otg_core_if_t * core_if);
-+#define dwc_param_tx_thr_length_default 64
-+
-+/** Thresholding length for Rx
-+ * FIFOs in 32 bit DWORDs
-+ */
-+extern int dwc_otg_set_param_rx_thr_length(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_rx_thr_length(dwc_otg_core_if_t * core_if);
-+#define dwc_param_rx_thr_length_default 64
-+
-+/**
-+ * Specifies whether LPM (Link Power Management) support is enabled
-+ */
-+extern int dwc_otg_set_param_lpm_enable(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_lpm_enable(dwc_otg_core_if_t * core_if);
-+#define dwc_param_lpm_enable_default 1
-+
-+/**
-+ * Specifies whether PTI enhancement is enabled
-+ */
-+extern int dwc_otg_set_param_pti_enable(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_pti_enable(dwc_otg_core_if_t * core_if);
-+#define dwc_param_pti_enable_default 0
-+
-+/**
-+ * Specifies whether MPI enhancement is enabled
-+ */
-+extern int dwc_otg_set_param_mpi_enable(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_mpi_enable(dwc_otg_core_if_t * core_if);
-+#define dwc_param_mpi_enable_default 0
-+
-+/**
-+ * Specifies whether ADP capability is enabled
-+ */
-+extern int dwc_otg_set_param_adp_enable(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_adp_enable(dwc_otg_core_if_t * core_if);
-+#define dwc_param_adp_enable_default 0
-+
-+/**
-+ * Specifies whether IC_USB capability is enabled
-+ */
-+
-+extern int dwc_otg_set_param_ic_usb_cap(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_ic_usb_cap(dwc_otg_core_if_t * core_if);
-+#define dwc_param_ic_usb_cap_default 0
-+
-+extern int dwc_otg_set_param_ahb_thr_ratio(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_ahb_thr_ratio(dwc_otg_core_if_t * core_if);
-+#define dwc_param_ahb_thr_ratio_default 0
-+
-+extern int dwc_otg_set_param_power_down(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_power_down(dwc_otg_core_if_t * core_if);
-+#define dwc_param_power_down_default 0
-+
-+extern int dwc_otg_set_param_reload_ctl(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_reload_ctl(dwc_otg_core_if_t * core_if);
-+#define dwc_param_reload_ctl_default 0
-+
-+extern int dwc_otg_set_param_dev_out_nak(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_dev_out_nak(dwc_otg_core_if_t * core_if);
-+#define dwc_param_dev_out_nak_default 0
-+
-+extern int dwc_otg_set_param_cont_on_bna(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_cont_on_bna(dwc_otg_core_if_t * core_if);
-+#define dwc_param_cont_on_bna_default 0
-+
-+extern int dwc_otg_set_param_ahb_single(dwc_otg_core_if_t * core_if,
-+ int32_t val);
-+extern int32_t dwc_otg_get_param_ahb_single(dwc_otg_core_if_t * core_if);
-+#define dwc_param_ahb_single_default 0
-+
-+extern int dwc_otg_set_param_otg_ver(dwc_otg_core_if_t * core_if, int32_t val);
-+extern int32_t dwc_otg_get_param_otg_ver(dwc_otg_core_if_t * core_if);
-+#define dwc_param_otg_ver_default 0
-+
-+/** @} */
-+
-+/** @name Access to registers and bit-fields */
-+
-+/**
-+ * Dump core registers and SPRAM
-+ */
-+extern void dwc_otg_dump_dev_registers(dwc_otg_core_if_t * _core_if);
-+extern void dwc_otg_dump_spram(dwc_otg_core_if_t * _core_if);
-+extern void dwc_otg_dump_host_registers(dwc_otg_core_if_t * _core_if);
-+extern void dwc_otg_dump_global_registers(dwc_otg_core_if_t * _core_if);
-+
-+/**
-+ * Get host negotiation status.
-+ */
-+extern uint32_t dwc_otg_get_hnpstatus(dwc_otg_core_if_t * core_if);
-+
-+/**
-+ * Get srp status
-+ */
-+extern uint32_t dwc_otg_get_srpstatus(dwc_otg_core_if_t * core_if);
-+
-+/**
-+ * Set hnpreq bit in the GOTGCTL register.
-+ */
-+extern void dwc_otg_set_hnpreq(dwc_otg_core_if_t * core_if, uint32_t val);
-+
-+/**
-+ * Get Content of SNPSID register.
-+ */
-+extern uint32_t dwc_otg_get_gsnpsid(dwc_otg_core_if_t * core_if);
-+
-+/**
-+ * Get current mode.
-+ * Returns 0 if in device mode, and 1 if in host mode.
-+ */
-+extern uint32_t dwc_otg_get_mode(dwc_otg_core_if_t * core_if);
-+
-+/**
-+ * Get value of hnpcapable field in the GUSBCFG register
-+ */
-+extern uint32_t dwc_otg_get_hnpcapable(dwc_otg_core_if_t * core_if);
-+/**
-+ * Set value of hnpcapable field in the GUSBCFG register
-+ */
-+extern void dwc_otg_set_hnpcapable(dwc_otg_core_if_t * core_if, uint32_t val);
-+
-+/**
-+ * Get value of srpcapable field in the GUSBCFG register
-+ */
-+extern uint32_t dwc_otg_get_srpcapable(dwc_otg_core_if_t * core_if);
-+/**
-+ * Set value of srpcapable field in the GUSBCFG register
-+ */
-+extern void dwc_otg_set_srpcapable(dwc_otg_core_if_t * core_if, uint32_t val);
-+
-+/**
-+ * Get value of devspeed field in the DCFG register
-+ */
-+extern uint32_t dwc_otg_get_devspeed(dwc_otg_core_if_t * core_if);
-+/**
-+ * Set value of devspeed field in the DCFG register
-+ */
-+extern void dwc_otg_set_devspeed(dwc_otg_core_if_t * core_if, uint32_t val);
-+
-+/**
-+ * Get the value of busconnected field from the HPRT0 register
-+ */
-+extern uint32_t dwc_otg_get_busconnected(dwc_otg_core_if_t * core_if);
-+
-+/**
-+ * Gets the device enumeration Speed.
-+ */
-+extern uint32_t dwc_otg_get_enumspeed(dwc_otg_core_if_t * core_if);
-+
-+/**
-+ * Get value of prtpwr field from the HPRT0 register
-+ */
-+extern uint32_t dwc_otg_get_prtpower(dwc_otg_core_if_t * core_if);
-+
-+/**
-+ * Get value of flag indicating core state - hibernated or not
-+ */
-+extern uint32_t dwc_otg_get_core_state(dwc_otg_core_if_t * core_if);
-+
-+/**
-+ * Set value of prtpwr field from the HPRT0 register
-+ */
-+extern void dwc_otg_set_prtpower(dwc_otg_core_if_t * core_if, uint32_t val);
-+
-+/**
-+ * Get value of prtsusp field from the HPRT0 regsiter
-+ */
-+extern uint32_t dwc_otg_get_prtsuspend(dwc_otg_core_if_t * core_if);
-+/**
-+ * Set value of prtpwr field from the HPRT0 register
-+ */
-+extern void dwc_otg_set_prtsuspend(dwc_otg_core_if_t * core_if, uint32_t val);
-+
-+/**
-+ * Get value of ModeChTimEn field from the HCFG regsiter
-+ */
-+extern uint32_t dwc_otg_get_mode_ch_tim(dwc_otg_core_if_t * core_if);
-+/**
-+ * Set value of ModeChTimEn field from the HCFG regsiter
-+ */
-+extern void dwc_otg_set_mode_ch_tim(dwc_otg_core_if_t * core_if, uint32_t val);
-+
-+/**
-+ * Get value of Fram Interval field from the HFIR regsiter
-+ */
-+extern uint32_t dwc_otg_get_fr_interval(dwc_otg_core_if_t * core_if);
-+/**
-+ * Set value of Frame Interval field from the HFIR regsiter
-+ */
-+extern void dwc_otg_set_fr_interval(dwc_otg_core_if_t * core_if, uint32_t val);
-+
-+/**
-+ * Set value of prtres field from the HPRT0 register
-+ *FIXME Remove?
-+ */
-+extern void dwc_otg_set_prtresume(dwc_otg_core_if_t * core_if, uint32_t val);
-+
-+/**
-+ * Get value of rmtwkupsig bit in DCTL register
-+ */
-+extern uint32_t dwc_otg_get_remotewakesig(dwc_otg_core_if_t * core_if);
-+
-+/**
-+ * Get value of prt_sleep_sts field from the GLPMCFG register
-+ */
-+extern uint32_t dwc_otg_get_lpm_portsleepstatus(dwc_otg_core_if_t * core_if);
-+
-+/**
-+ * Get value of rem_wkup_en field from the GLPMCFG register
-+ */
-+extern uint32_t dwc_otg_get_lpm_remotewakeenabled(dwc_otg_core_if_t * core_if);
-+
-+/**
-+ * Get value of appl_resp field from the GLPMCFG register
-+ */
-+extern uint32_t dwc_otg_get_lpmresponse(dwc_otg_core_if_t * core_if);
-+/**
-+ * Set value of appl_resp field from the GLPMCFG register
-+ */
-+extern void dwc_otg_set_lpmresponse(dwc_otg_core_if_t * core_if, uint32_t val);
-+
-+/**
-+ * Get value of hsic_connect field from the GLPMCFG register
-+ */
-+extern uint32_t dwc_otg_get_hsic_connect(dwc_otg_core_if_t * core_if);
-+/**
-+ * Set value of hsic_connect field from the GLPMCFG register
-+ */
-+extern void dwc_otg_set_hsic_connect(dwc_otg_core_if_t * core_if, uint32_t val);
-+
-+/**
-+ * Get value of inv_sel_hsic field from the GLPMCFG register.
-+ */
-+extern uint32_t dwc_otg_get_inv_sel_hsic(dwc_otg_core_if_t * core_if);
-+/**
-+ * Set value of inv_sel_hsic field from the GLPMFG register.
-+ */
-+extern void dwc_otg_set_inv_sel_hsic(dwc_otg_core_if_t * core_if, uint32_t val);
-+
-+/*
-+ * Some functions for accessing registers
-+ */
-+
-+/**
-+ * GOTGCTL register
-+ */
-+extern uint32_t dwc_otg_get_gotgctl(dwc_otg_core_if_t * core_if);
-+extern void dwc_otg_set_gotgctl(dwc_otg_core_if_t * core_if, uint32_t val);
-+
-+/**
-+ * GUSBCFG register
-+ */
-+extern uint32_t dwc_otg_get_gusbcfg(dwc_otg_core_if_t * core_if);
-+extern void dwc_otg_set_gusbcfg(dwc_otg_core_if_t * core_if, uint32_t val);
-+
-+/**
-+ * GRXFSIZ register
-+ */
-+extern uint32_t dwc_otg_get_grxfsiz(dwc_otg_core_if_t * core_if);
-+extern void dwc_otg_set_grxfsiz(dwc_otg_core_if_t * core_if, uint32_t val);
-+
-+/**
-+ * GNPTXFSIZ register
-+ */
-+extern uint32_t dwc_otg_get_gnptxfsiz(dwc_otg_core_if_t * core_if);
-+extern void dwc_otg_set_gnptxfsiz(dwc_otg_core_if_t * core_if, uint32_t val);
-+
-+extern uint32_t dwc_otg_get_gpvndctl(dwc_otg_core_if_t * core_if);
-+extern void dwc_otg_set_gpvndctl(dwc_otg_core_if_t * core_if, uint32_t val);
-+
-+/**
-+ * GGPIO register
-+ */
-+extern uint32_t dwc_otg_get_ggpio(dwc_otg_core_if_t * core_if);
-+extern void dwc_otg_set_ggpio(dwc_otg_core_if_t * core_if, uint32_t val);
-+
-+/**
-+ * GUID register
-+ */
-+extern uint32_t dwc_otg_get_guid(dwc_otg_core_if_t * core_if);
-+extern void dwc_otg_set_guid(dwc_otg_core_if_t * core_if, uint32_t val);
-+
-+/**
-+ * HPRT0 register
-+ */
-+extern uint32_t dwc_otg_get_hprt0(dwc_otg_core_if_t * core_if);
-+extern void dwc_otg_set_hprt0(dwc_otg_core_if_t * core_if, uint32_t val);
-+
-+/**
-+ * GHPTXFSIZE
-+ */
-+extern uint32_t dwc_otg_get_hptxfsiz(dwc_otg_core_if_t * core_if);
-+
-+/** @} */
-+
-+#endif /* __DWC_CORE_IF_H__ */
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_dbg.h
-@@ -0,0 +1,117 @@
-+/* ==========================================================================
-+ *
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+
-+#ifndef __DWC_OTG_DBG_H__
-+#define __DWC_OTG_DBG_H__
-+
-+/** @file
-+ * This file defines debug levels.
-+ * Debugging support vanishes in non-debug builds.
-+ */
-+
-+/**
-+ * The Debug Level bit-mask variable.
-+ */
-+extern uint32_t g_dbg_lvl;
-+/**
-+ * Set the Debug Level variable.
-+ */
-+static inline uint32_t SET_DEBUG_LEVEL(const uint32_t new)
-+{
-+ uint32_t old = g_dbg_lvl;
-+ g_dbg_lvl = new;
-+ return old;
-+}
-+
-+#define DBG_USER (0x1)
-+/** When debug level has the DBG_CIL bit set, display CIL Debug messages. */
-+#define DBG_CIL (0x2)
-+/** When debug level has the DBG_CILV bit set, display CIL Verbose debug
-+ * messages */
-+#define DBG_CILV (0x20)
-+/** When debug level has the DBG_PCD bit set, display PCD (Device) debug
-+ * messages */
-+#define DBG_PCD (0x4)
-+/** When debug level has the DBG_PCDV set, display PCD (Device) Verbose debug
-+ * messages */
-+#define DBG_PCDV (0x40)
-+/** When debug level has the DBG_HCD bit set, display Host debug messages */
-+#define DBG_HCD (0x8)
-+/** When debug level has the DBG_HCDV bit set, display Verbose Host debug
-+ * messages */
-+#define DBG_HCDV (0x80)
-+/** When debug level has the DBG_HCD_URB bit set, display enqueued URBs in host
-+ * mode. */
-+#define DBG_HCD_URB (0x800)
-+/** When debug level has the DBG_HCDI bit set, display host interrupt
-+ * messages. */
-+#define DBG_HCDI (0x1000)
-+
-+/** When debug level has any bit set, display debug messages */
-+#define DBG_ANY (0xFF)
-+
-+/** All debug messages off */
-+#define DBG_OFF 0
-+
-+/** Prefix string for DWC_DEBUG print macros. */
-+#define USB_DWC "DWC_otg: "
-+
-+/**
-+ * Print a debug message when the Global debug level variable contains
-+ * the bit defined in <code>lvl</code>.
-+ *
-+ * @param[in] lvl - Debug level, use one of the DBG_ constants above.
-+ * @param[in] x - like printf
-+ *
-+ * Example:<p>
-+ * <code>
-+ * DWC_DEBUGPL( DBG_ANY, "%s(%p)\n", __func__, _reg_base_addr);
-+ * </code>
-+ * <br>
-+ * results in:<br>
-+ * <code>
-+ * usb-DWC_otg: dwc_otg_cil_init(ca867000)
-+ * </code>
-+ */
-+#ifdef DEBUG
-+
-+# define DWC_DEBUGPL(lvl, x...) do{ if ((lvl)&g_dbg_lvl)__DWC_DEBUG(USB_DWC x ); }while(0)
-+# define DWC_DEBUGP(x...) DWC_DEBUGPL(DBG_ANY, x )
-+
-+# define CHK_DEBUG_LEVEL(level) ((level) & g_dbg_lvl)
-+
-+#else
-+
-+# define DWC_DEBUGPL(lvl, x...) do{}while(0)
-+# define DWC_DEBUGP(x...)
-+
-+# define CHK_DEBUG_LEVEL(level) (0)
-+
-+#endif /*DEBUG*/
-+#endif
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_driver.c
-@@ -0,0 +1,1757 @@
-+/* ==========================================================================
-+ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_driver.c $
-+ * $Revision: #92 $
-+ * $Date: 2012/08/10 $
-+ * $Change: 2047372 $
-+ *
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+
-+/** @file
-+ * The dwc_otg_driver module provides the initialization and cleanup entry
-+ * points for the DWC_otg driver. This module will be dynamically installed
-+ * after Linux is booted using the insmod command. When the module is
-+ * installed, the dwc_otg_driver_init function is called. When the module is
-+ * removed (using rmmod), the dwc_otg_driver_cleanup function is called.
-+ *
-+ * This module also defines a data structure for the dwc_otg_driver, which is
-+ * used in conjunction with the standard ARM lm_device structure. These
-+ * structures allow the OTG driver to comply with the standard Linux driver
-+ * model in which devices and drivers are registered with a bus driver. This
-+ * has the benefit that Linux can expose attributes of the driver and device
-+ * in its special sysfs file system. Users can then read or write files in
-+ * this file system to perform diagnostics on the driver components or the
-+ * device.
-+ */
-+
-+#include "dwc_otg_os_dep.h"
-+#include "dwc_os.h"
-+#include "dwc_otg_dbg.h"
-+#include "dwc_otg_driver.h"
-+#include "dwc_otg_attr.h"
-+#include "dwc_otg_core_if.h"
-+#include "dwc_otg_pcd_if.h"
-+#include "dwc_otg_hcd_if.h"
-+#include "dwc_otg_fiq_fsm.h"
-+
-+#define DWC_DRIVER_VERSION "3.00a 10-AUG-2012"
-+#define DWC_DRIVER_DESC "HS OTG USB Controller driver"
-+
-+bool microframe_schedule=true;
-+
-+static const char dwc_driver_name[] = "dwc_otg";
-+
-+
-+extern int pcd_init(
-+#ifdef LM_INTERFACE
-+ struct lm_device *_dev
-+#elif defined(PCI_INTERFACE)
-+ struct pci_dev *_dev
-+#elif defined(PLATFORM_INTERFACE)
-+ struct platform_device *dev
-+#endif
-+ );
-+extern int hcd_init(
-+#ifdef LM_INTERFACE
-+ struct lm_device *_dev
-+#elif defined(PCI_INTERFACE)
-+ struct pci_dev *_dev
-+#elif defined(PLATFORM_INTERFACE)
-+ struct platform_device *dev
-+#endif
-+ );
-+
-+extern int pcd_remove(
-+#ifdef LM_INTERFACE
-+ struct lm_device *_dev
-+#elif defined(PCI_INTERFACE)
-+ struct pci_dev *_dev
-+#elif defined(PLATFORM_INTERFACE)
-+ struct platform_device *_dev
-+#endif
-+ );
-+
-+extern void hcd_remove(
-+#ifdef LM_INTERFACE
-+ struct lm_device *_dev
-+#elif defined(PCI_INTERFACE)
-+ struct pci_dev *_dev
-+#elif defined(PLATFORM_INTERFACE)
-+ struct platform_device *_dev
-+#endif
-+ );
-+
-+extern void dwc_otg_adp_start(dwc_otg_core_if_t * core_if, uint8_t is_host);
-+
-+/*-------------------------------------------------------------------------*/
-+/* Encapsulate the module parameter settings */
-+
-+struct dwc_otg_driver_module_params {
-+ int32_t opt;
-+ int32_t otg_cap;
-+ int32_t dma_enable;
-+ int32_t dma_desc_enable;
-+ int32_t dma_burst_size;
-+ int32_t speed;
-+ int32_t host_support_fs_ls_low_power;
-+ int32_t host_ls_low_power_phy_clk;
-+ int32_t enable_dynamic_fifo;
-+ int32_t data_fifo_size;
-+ int32_t dev_rx_fifo_size;
-+ int32_t dev_nperio_tx_fifo_size;
-+ uint32_t dev_perio_tx_fifo_size[MAX_PERIO_FIFOS];
-+ int32_t host_rx_fifo_size;
-+ int32_t host_nperio_tx_fifo_size;
-+ int32_t host_perio_tx_fifo_size;
-+ int32_t max_transfer_size;
-+ int32_t max_packet_count;
-+ int32_t host_channels;
-+ int32_t dev_endpoints;
-+ int32_t phy_type;
-+ int32_t phy_utmi_width;
-+ int32_t phy_ulpi_ddr;
-+ int32_t phy_ulpi_ext_vbus;
-+ int32_t i2c_enable;
-+ int32_t ulpi_fs_ls;
-+ int32_t ts_dline;
-+ int32_t en_multiple_tx_fifo;
-+ uint32_t dev_tx_fifo_size[MAX_TX_FIFOS];
-+ uint32_t thr_ctl;
-+ uint32_t tx_thr_length;
-+ uint32_t rx_thr_length;
-+ int32_t pti_enable;
-+ int32_t mpi_enable;
-+ int32_t lpm_enable;
-+ int32_t ic_usb_cap;
-+ int32_t ahb_thr_ratio;
-+ int32_t power_down;
-+ int32_t reload_ctl;
-+ int32_t dev_out_nak;
-+ int32_t cont_on_bna;
-+ int32_t ahb_single;
-+ int32_t otg_ver;
-+ int32_t adp_enable;
-+};
-+
-+static struct dwc_otg_driver_module_params dwc_otg_module_params = {
-+ .opt = -1,
-+ .otg_cap = -1,
-+ .dma_enable = -1,
-+ .dma_desc_enable = -1,
-+ .dma_burst_size = -1,
-+ .speed = -1,
-+ .host_support_fs_ls_low_power = -1,
-+ .host_ls_low_power_phy_clk = -1,
-+ .enable_dynamic_fifo = -1,
-+ .data_fifo_size = -1,
-+ .dev_rx_fifo_size = -1,
-+ .dev_nperio_tx_fifo_size = -1,
-+ .dev_perio_tx_fifo_size = {
-+ /* dev_perio_tx_fifo_size_1 */
-+ -1,
-+ -1,
-+ -1,
-+ -1,
-+ -1,
-+ -1,
-+ -1,
-+ -1,
-+ -1,
-+ -1,
-+ -1,
-+ -1,
-+ -1,
-+ -1,
-+ -1
-+ /* 15 */
-+ },
-+ .host_rx_fifo_size = -1,
-+ .host_nperio_tx_fifo_size = -1,
-+ .host_perio_tx_fifo_size = -1,
-+ .max_transfer_size = -1,
-+ .max_packet_count = -1,
-+ .host_channels = -1,
-+ .dev_endpoints = -1,
-+ .phy_type = -1,
-+ .phy_utmi_width = -1,
-+ .phy_ulpi_ddr = -1,
-+ .phy_ulpi_ext_vbus = -1,
-+ .i2c_enable = -1,
-+ .ulpi_fs_ls = -1,
-+ .ts_dline = -1,
-+ .en_multiple_tx_fifo = -1,
-+ .dev_tx_fifo_size = {
-+ /* dev_tx_fifo_size */
-+ -1,
-+ -1,
-+ -1,
-+ -1,
-+ -1,
-+ -1,
-+ -1,
-+ -1,
-+ -1,
-+ -1,
-+ -1,
-+ -1,
-+ -1,
-+ -1,
-+ -1
-+ /* 15 */
-+ },
-+ .thr_ctl = -1,
-+ .tx_thr_length = -1,
-+ .rx_thr_length = -1,
-+ .pti_enable = -1,
-+ .mpi_enable = -1,
-+ .lpm_enable = 0,
-+ .ic_usb_cap = -1,
-+ .ahb_thr_ratio = -1,
-+ .power_down = -1,
-+ .reload_ctl = -1,
-+ .dev_out_nak = -1,
-+ .cont_on_bna = -1,
-+ .ahb_single = -1,
-+ .otg_ver = -1,
-+ .adp_enable = -1,
-+};
-+
-+//Global variable to switch the fiq fix on or off
-+bool fiq_enable = 1;
-+// Global variable to enable the split transaction fix
-+bool fiq_fsm_enable = true;
-+//Bulk split-transaction NAK holdoff in microframes
-+uint16_t nak_holdoff = 8;
-+
-+unsigned short fiq_fsm_mask = 0x07;
-+
-+/**
-+ * This function shows the Driver Version.
-+ */
-+static ssize_t version_show(struct device_driver *dev, char *buf)
-+{
-+ return snprintf(buf, sizeof(DWC_DRIVER_VERSION) + 2, "%s\n",
-+ DWC_DRIVER_VERSION);
-+}
-+
-+static DRIVER_ATTR(version, S_IRUGO, version_show, NULL);
-+
-+/**
-+ * Global Debug Level Mask.
-+ */
-+uint32_t g_dbg_lvl = 0; /* OFF */
-+
-+/**
-+ * This function shows the driver Debug Level.
-+ */
-+static ssize_t dbg_level_show(struct device_driver *drv, char *buf)
-+{
-+ return sprintf(buf, "0x%0x\n", g_dbg_lvl);
-+}
-+
-+/**
-+ * This function stores the driver Debug Level.
-+ */
-+static ssize_t dbg_level_store(struct device_driver *drv, const char *buf,
-+ size_t count)
-+{
-+ g_dbg_lvl = simple_strtoul(buf, NULL, 16);
-+ return count;
-+}
-+
-+static DRIVER_ATTR(debuglevel, S_IRUGO | S_IWUSR, dbg_level_show,
-+ dbg_level_store);
-+
-+/**
-+ * This function is called during module intialization
-+ * to pass module parameters to the DWC_OTG CORE.
-+ */
-+static int set_parameters(dwc_otg_core_if_t * core_if)
-+{
-+ int retval = 0;
-+ int i;
-+
-+ if (dwc_otg_module_params.otg_cap != -1) {
-+ retval +=
-+ dwc_otg_set_param_otg_cap(core_if,
-+ dwc_otg_module_params.otg_cap);
-+ }
-+ if (dwc_otg_module_params.dma_enable != -1) {
-+ retval +=
-+ dwc_otg_set_param_dma_enable(core_if,
-+ dwc_otg_module_params.
-+ dma_enable);
-+ }
-+ if (dwc_otg_module_params.dma_desc_enable != -1) {
-+ retval +=
-+ dwc_otg_set_param_dma_desc_enable(core_if,
-+ dwc_otg_module_params.
-+ dma_desc_enable);
-+ }
-+ if (dwc_otg_module_params.opt != -1) {
-+ retval +=
-+ dwc_otg_set_param_opt(core_if, dwc_otg_module_params.opt);
-+ }
-+ if (dwc_otg_module_params.dma_burst_size != -1) {
-+ retval +=
-+ dwc_otg_set_param_dma_burst_size(core_if,
-+ dwc_otg_module_params.
-+ dma_burst_size);
-+ }
-+ if (dwc_otg_module_params.host_support_fs_ls_low_power != -1) {
-+ retval +=
-+ dwc_otg_set_param_host_support_fs_ls_low_power(core_if,
-+ dwc_otg_module_params.
-+ host_support_fs_ls_low_power);
-+ }
-+ if (dwc_otg_module_params.enable_dynamic_fifo != -1) {
-+ retval +=
-+ dwc_otg_set_param_enable_dynamic_fifo(core_if,
-+ dwc_otg_module_params.
-+ enable_dynamic_fifo);
-+ }
-+ if (dwc_otg_module_params.data_fifo_size != -1) {
-+ retval +=
-+ dwc_otg_set_param_data_fifo_size(core_if,
-+ dwc_otg_module_params.
-+ data_fifo_size);
-+ }
-+ if (dwc_otg_module_params.dev_rx_fifo_size != -1) {
-+ retval +=
-+ dwc_otg_set_param_dev_rx_fifo_size(core_if,
-+ dwc_otg_module_params.
-+ dev_rx_fifo_size);
-+ }
-+ if (dwc_otg_module_params.dev_nperio_tx_fifo_size != -1) {
-+ retval +=
-+ dwc_otg_set_param_dev_nperio_tx_fifo_size(core_if,
-+ dwc_otg_module_params.
-+ dev_nperio_tx_fifo_size);
-+ }
-+ if (dwc_otg_module_params.host_rx_fifo_size != -1) {
-+ retval +=
-+ dwc_otg_set_param_host_rx_fifo_size(core_if,
-+ dwc_otg_module_params.host_rx_fifo_size);
-+ }
-+ if (dwc_otg_module_params.host_nperio_tx_fifo_size != -1) {
-+ retval +=
-+ dwc_otg_set_param_host_nperio_tx_fifo_size(core_if,
-+ dwc_otg_module_params.
-+ host_nperio_tx_fifo_size);
-+ }
-+ if (dwc_otg_module_params.host_perio_tx_fifo_size != -1) {
-+ retval +=
-+ dwc_otg_set_param_host_perio_tx_fifo_size(core_if,
-+ dwc_otg_module_params.
-+ host_perio_tx_fifo_size);
-+ }
-+ if (dwc_otg_module_params.max_transfer_size != -1) {
-+ retval +=
-+ dwc_otg_set_param_max_transfer_size(core_if,
-+ dwc_otg_module_params.
-+ max_transfer_size);
-+ }
-+ if (dwc_otg_module_params.max_packet_count != -1) {
-+ retval +=
-+ dwc_otg_set_param_max_packet_count(core_if,
-+ dwc_otg_module_params.
-+ max_packet_count);
-+ }
-+ if (dwc_otg_module_params.host_channels != -1) {
-+ retval +=
-+ dwc_otg_set_param_host_channels(core_if,
-+ dwc_otg_module_params.
-+ host_channels);
-+ }
-+ if (dwc_otg_module_params.dev_endpoints != -1) {
-+ retval +=
-+ dwc_otg_set_param_dev_endpoints(core_if,
-+ dwc_otg_module_params.
-+ dev_endpoints);
-+ }
-+ if (dwc_otg_module_params.phy_type != -1) {
-+ retval +=
-+ dwc_otg_set_param_phy_type(core_if,
-+ dwc_otg_module_params.phy_type);
-+ }
-+ if (dwc_otg_module_params.speed != -1) {
-+ retval +=
-+ dwc_otg_set_param_speed(core_if,
-+ dwc_otg_module_params.speed);
-+ }
-+ if (dwc_otg_module_params.host_ls_low_power_phy_clk != -1) {
-+ retval +=
-+ dwc_otg_set_param_host_ls_low_power_phy_clk(core_if,
-+ dwc_otg_module_params.
-+ host_ls_low_power_phy_clk);
-+ }
-+ if (dwc_otg_module_params.phy_ulpi_ddr != -1) {
-+ retval +=
-+ dwc_otg_set_param_phy_ulpi_ddr(core_if,
-+ dwc_otg_module_params.
-+ phy_ulpi_ddr);
-+ }
-+ if (dwc_otg_module_params.phy_ulpi_ext_vbus != -1) {
-+ retval +=
-+ dwc_otg_set_param_phy_ulpi_ext_vbus(core_if,
-+ dwc_otg_module_params.
-+ phy_ulpi_ext_vbus);
-+ }
-+ if (dwc_otg_module_params.phy_utmi_width != -1) {
-+ retval +=
-+ dwc_otg_set_param_phy_utmi_width(core_if,
-+ dwc_otg_module_params.
-+ phy_utmi_width);
-+ }
-+ if (dwc_otg_module_params.ulpi_fs_ls != -1) {
-+ retval +=
-+ dwc_otg_set_param_ulpi_fs_ls(core_if,
-+ dwc_otg_module_params.ulpi_fs_ls);
-+ }
-+ if (dwc_otg_module_params.ts_dline != -1) {
-+ retval +=
-+ dwc_otg_set_param_ts_dline(core_if,
-+ dwc_otg_module_params.ts_dline);
-+ }
-+ if (dwc_otg_module_params.i2c_enable != -1) {
-+ retval +=
-+ dwc_otg_set_param_i2c_enable(core_if,
-+ dwc_otg_module_params.
-+ i2c_enable);
-+ }
-+ if (dwc_otg_module_params.en_multiple_tx_fifo != -1) {
-+ retval +=
-+ dwc_otg_set_param_en_multiple_tx_fifo(core_if,
-+ dwc_otg_module_params.
-+ en_multiple_tx_fifo);
-+ }
-+ for (i = 0; i < 15; i++) {
-+ if (dwc_otg_module_params.dev_perio_tx_fifo_size[i] != -1) {
-+ retval +=
-+ dwc_otg_set_param_dev_perio_tx_fifo_size(core_if,
-+ dwc_otg_module_params.
-+ dev_perio_tx_fifo_size
-+ [i], i);
-+ }
-+ }
-+
-+ for (i = 0; i < 15; i++) {
-+ if (dwc_otg_module_params.dev_tx_fifo_size[i] != -1) {
-+ retval += dwc_otg_set_param_dev_tx_fifo_size(core_if,
-+ dwc_otg_module_params.
-+ dev_tx_fifo_size
-+ [i], i);
-+ }
-+ }
-+ if (dwc_otg_module_params.thr_ctl != -1) {
-+ retval +=
-+ dwc_otg_set_param_thr_ctl(core_if,
-+ dwc_otg_module_params.thr_ctl);
-+ }
-+ if (dwc_otg_module_params.mpi_enable != -1) {
-+ retval +=
-+ dwc_otg_set_param_mpi_enable(core_if,
-+ dwc_otg_module_params.
-+ mpi_enable);
-+ }
-+ if (dwc_otg_module_params.pti_enable != -1) {
-+ retval +=
-+ dwc_otg_set_param_pti_enable(core_if,
-+ dwc_otg_module_params.
-+ pti_enable);
-+ }
-+ if (dwc_otg_module_params.lpm_enable != -1) {
-+ retval +=
-+ dwc_otg_set_param_lpm_enable(core_if,
-+ dwc_otg_module_params.
-+ lpm_enable);
-+ }
-+ if (dwc_otg_module_params.ic_usb_cap != -1) {
-+ retval +=
-+ dwc_otg_set_param_ic_usb_cap(core_if,
-+ dwc_otg_module_params.
-+ ic_usb_cap);
-+ }
-+ if (dwc_otg_module_params.tx_thr_length != -1) {
-+ retval +=
-+ dwc_otg_set_param_tx_thr_length(core_if,
-+ dwc_otg_module_params.tx_thr_length);
-+ }
-+ if (dwc_otg_module_params.rx_thr_length != -1) {
-+ retval +=
-+ dwc_otg_set_param_rx_thr_length(core_if,
-+ dwc_otg_module_params.
-+ rx_thr_length);
-+ }
-+ if (dwc_otg_module_params.ahb_thr_ratio != -1) {
-+ retval +=
-+ dwc_otg_set_param_ahb_thr_ratio(core_if,
-+ dwc_otg_module_params.ahb_thr_ratio);
-+ }
-+ if (dwc_otg_module_params.power_down != -1) {
-+ retval +=
-+ dwc_otg_set_param_power_down(core_if,
-+ dwc_otg_module_params.power_down);
-+ }
-+ if (dwc_otg_module_params.reload_ctl != -1) {
-+ retval +=
-+ dwc_otg_set_param_reload_ctl(core_if,
-+ dwc_otg_module_params.reload_ctl);
-+ }
-+
-+ if (dwc_otg_module_params.dev_out_nak != -1) {
-+ retval +=
-+ dwc_otg_set_param_dev_out_nak(core_if,
-+ dwc_otg_module_params.dev_out_nak);
-+ }
-+
-+ if (dwc_otg_module_params.cont_on_bna != -1) {
-+ retval +=
-+ dwc_otg_set_param_cont_on_bna(core_if,
-+ dwc_otg_module_params.cont_on_bna);
-+ }
-+
-+ if (dwc_otg_module_params.ahb_single != -1) {
-+ retval +=
-+ dwc_otg_set_param_ahb_single(core_if,
-+ dwc_otg_module_params.ahb_single);
-+ }
-+
-+ if (dwc_otg_module_params.otg_ver != -1) {
-+ retval +=
-+ dwc_otg_set_param_otg_ver(core_if,
-+ dwc_otg_module_params.otg_ver);
-+ }
-+ if (dwc_otg_module_params.adp_enable != -1) {
-+ retval +=
-+ dwc_otg_set_param_adp_enable(core_if,
-+ dwc_otg_module_params.
-+ adp_enable);
-+ }
-+ return retval;
-+}
-+
-+/**
-+ * This function is the top level interrupt handler for the Common
-+ * (Device and host modes) interrupts.
-+ */
-+static irqreturn_t dwc_otg_common_irq(int irq, void *dev)
-+{
-+ int32_t retval = IRQ_NONE;
-+
-+ retval = dwc_otg_handle_common_intr(dev);
-+ if (retval != 0) {
-+ S3C2410X_CLEAR_EINTPEND();
-+ }
-+ return IRQ_RETVAL(retval);
-+}
-+
-+/**
-+ * This function is called when a lm_device is unregistered with the
-+ * dwc_otg_driver. This happens, for example, when the rmmod command is
-+ * executed. The device may or may not be electrically present. If it is
-+ * present, the driver stops device processing. Any resources used on behalf
-+ * of this device are freed.
-+ *
-+ * @param _dev
-+ */
-+#ifdef LM_INTERFACE
-+#define REM_RETVAL(n)
-+static void dwc_otg_driver_remove( struct lm_device *_dev )
-+{ dwc_otg_device_t *otg_dev = lm_get_drvdata(_dev);
-+#elif defined(PCI_INTERFACE)
-+#define REM_RETVAL(n)
-+static void dwc_otg_driver_remove( struct pci_dev *_dev )
-+{ dwc_otg_device_t *otg_dev = pci_get_drvdata(_dev);
-+#elif defined(PLATFORM_INTERFACE)
-+#define REM_RETVAL(n) n
-+static int dwc_otg_driver_remove( struct platform_device *_dev )
-+{ dwc_otg_device_t *otg_dev = platform_get_drvdata(_dev);
-+#endif
-+
-+ DWC_DEBUGPL(DBG_ANY, "%s(%p) otg_dev %p\n", __func__, _dev, otg_dev);
-+
-+ if (!otg_dev) {
-+ /* Memory allocation for the dwc_otg_device failed. */
-+ DWC_DEBUGPL(DBG_ANY, "%s: otg_dev NULL!\n", __func__);
-+ return REM_RETVAL(-ENOMEM);
-+ }
-+#ifndef DWC_DEVICE_ONLY
-+ if (otg_dev->hcd) {
-+ hcd_remove(_dev);
-+ } else {
-+ DWC_DEBUGPL(DBG_ANY, "%s: otg_dev->hcd NULL!\n", __func__);
-+ return REM_RETVAL(-EINVAL);
-+ }
-+#endif
-+
-+#ifndef DWC_HOST_ONLY
-+ if (otg_dev->pcd) {
-+ pcd_remove(_dev);
-+ } else {
-+ DWC_DEBUGPL(DBG_ANY, "%s: otg_dev->pcd NULL!\n", __func__);
-+ return REM_RETVAL(-EINVAL);
-+ }
-+#endif
-+ /*
-+ * Free the IRQ
-+ */
-+ if (otg_dev->common_irq_installed) {
-+#ifdef PLATFORM_INTERFACE
-+ free_irq(platform_get_irq(_dev, 0), otg_dev);
-+#else
-+ free_irq(_dev->irq, otg_dev);
-+#endif
-+ } else {
-+ DWC_DEBUGPL(DBG_ANY, "%s: There is no installed irq!\n", __func__);
-+ return REM_RETVAL(-ENXIO);
-+ }
-+
-+ if (otg_dev->core_if) {
-+ dwc_otg_cil_remove(otg_dev->core_if);
-+ } else {
-+ DWC_DEBUGPL(DBG_ANY, "%s: otg_dev->core_if NULL!\n", __func__);
-+ return REM_RETVAL(-ENXIO);
-+ }
-+
-+ /*
-+ * Remove the device attributes
-+ */
-+ dwc_otg_attr_remove(_dev);
-+
-+ /*
-+ * Return the memory.
-+ */
-+ if (otg_dev->os_dep.base) {
-+ iounmap(otg_dev->os_dep.base);
-+ }
-+ DWC_FREE(otg_dev);
-+
-+ /*
-+ * Clear the drvdata pointer.
-+ */
-+#ifdef LM_INTERFACE
-+ lm_set_drvdata(_dev, 0);
-+#elif defined(PCI_INTERFACE)
-+ release_mem_region(otg_dev->os_dep.rsrc_start,
-+ otg_dev->os_dep.rsrc_len);
-+ pci_set_drvdata(_dev, 0);
-+#elif defined(PLATFORM_INTERFACE)
-+ platform_set_drvdata(_dev, 0);
-+#endif
-+ return REM_RETVAL(0);
-+}
-+
-+/**
-+ * This function is called when an lm_device is bound to a
-+ * dwc_otg_driver. It creates the driver components required to
-+ * control the device (CIL, HCD, and PCD) and it initializes the
-+ * device. The driver components are stored in a dwc_otg_device
-+ * structure. A reference to the dwc_otg_device is saved in the
-+ * lm_device. This allows the driver to access the dwc_otg_device
-+ * structure on subsequent calls to driver methods for this device.
-+ *
-+ * @param _dev Bus device
-+ */
-+static int dwc_otg_driver_probe(
-+#ifdef LM_INTERFACE
-+ struct lm_device *_dev
-+#elif defined(PCI_INTERFACE)
-+ struct pci_dev *_dev,
-+ const struct pci_device_id *id
-+#elif defined(PLATFORM_INTERFACE)
-+ struct platform_device *_dev
-+#endif
-+ )
-+{
-+ int retval = 0;
-+ dwc_otg_device_t *dwc_otg_device;
-+ int devirq;
-+
-+ dev_dbg(&_dev->dev, "dwc_otg_driver_probe(%p)\n", _dev);
-+#ifdef LM_INTERFACE
-+ dev_dbg(&_dev->dev, "start=0x%08x\n", (unsigned)_dev->resource.start);
-+#elif defined(PCI_INTERFACE)
-+ if (!id) {
-+ DWC_ERROR("Invalid pci_device_id %p", id);
-+ return -EINVAL;
-+ }
-+
-+ if (!_dev || (pci_enable_device(_dev) < 0)) {
-+ DWC_ERROR("Invalid pci_device %p", _dev);
-+ return -ENODEV;
-+ }
-+ dev_dbg(&_dev->dev, "start=0x%08x\n", (unsigned)pci_resource_start(_dev,0));
-+ /* other stuff needed as well? */
-+
-+#elif defined(PLATFORM_INTERFACE)
-+ dev_dbg(&_dev->dev, "start=0x%08x (len 0x%x)\n",
-+ (unsigned)_dev->resource->start,
-+ (unsigned)(_dev->resource->end - _dev->resource->start));
-+#endif
-+
-+ dwc_otg_device = DWC_ALLOC(sizeof(dwc_otg_device_t));
-+
-+ if (!dwc_otg_device) {
-+ dev_err(&_dev->dev, "kmalloc of dwc_otg_device failed\n");
-+ return -ENOMEM;
-+ }
-+
-+ memset(dwc_otg_device, 0, sizeof(*dwc_otg_device));
-+ dwc_otg_device->os_dep.reg_offset = 0xFFFFFFFF;
-+ dwc_otg_device->os_dep.platformdev = _dev;
-+
-+ /*
-+ * Map the DWC_otg Core memory into virtual address space.
-+ */
-+#ifdef LM_INTERFACE
-+ dwc_otg_device->os_dep.base = ioremap(_dev->resource.start, SZ_256K);
-+
-+ if (!dwc_otg_device->os_dep.base) {
-+ dev_err(&_dev->dev, "ioremap() failed\n");
-+ DWC_FREE(dwc_otg_device);
-+ return -ENOMEM;
-+ }
-+ dev_dbg(&_dev->dev, "base=0x%08x\n",
-+ (unsigned)dwc_otg_device->os_dep.base);
-+#elif defined(PCI_INTERFACE)
-+ _dev->current_state = PCI_D0;
-+ _dev->dev.power.power_state = PMSG_ON;
-+
-+ if (!_dev->irq) {
-+ DWC_ERROR("Found HC with no IRQ. Check BIOS/PCI %s setup!",
-+ pci_name(_dev));
-+ iounmap(dwc_otg_device->os_dep.base);
-+ DWC_FREE(dwc_otg_device);
-+ return -ENODEV;
-+ }
-+
-+ dwc_otg_device->os_dep.rsrc_start = pci_resource_start(_dev, 0);
-+ dwc_otg_device->os_dep.rsrc_len = pci_resource_len(_dev, 0);
-+ DWC_DEBUGPL(DBG_ANY, "PCI resource: start=%08x, len=%08x\n",
-+ (unsigned)dwc_otg_device->os_dep.rsrc_start,
-+ (unsigned)dwc_otg_device->os_dep.rsrc_len);
-+ if (!request_mem_region
-+ (dwc_otg_device->os_dep.rsrc_start, dwc_otg_device->os_dep.rsrc_len,
-+ "dwc_otg")) {
-+ dev_dbg(&_dev->dev, "error requesting memory\n");
-+ iounmap(dwc_otg_device->os_dep.base);
-+ DWC_FREE(dwc_otg_device);
-+ return -EFAULT;
-+ }
-+
-+ dwc_otg_device->os_dep.base =
-+ ioremap_nocache(dwc_otg_device->os_dep.rsrc_start,
-+ dwc_otg_device->os_dep.rsrc_len);
-+ if (dwc_otg_device->os_dep.base == NULL) {
-+ dev_dbg(&_dev->dev, "error mapping memory\n");
-+ release_mem_region(dwc_otg_device->os_dep.rsrc_start,
-+ dwc_otg_device->os_dep.rsrc_len);
-+ iounmap(dwc_otg_device->os_dep.base);
-+ DWC_FREE(dwc_otg_device);
-+ return -EFAULT;
-+ }
-+ dev_dbg(&_dev->dev, "base=0x%p (before adjust) \n",
-+ dwc_otg_device->os_dep.base);
-+ dwc_otg_device->os_dep.base = (char *)dwc_otg_device->os_dep.base;
-+ dev_dbg(&_dev->dev, "base=0x%p (after adjust) \n",
-+ dwc_otg_device->os_dep.base);
-+ dev_dbg(&_dev->dev, "%s: mapped PA 0x%x to VA 0x%p\n", __func__,
-+ (unsigned)dwc_otg_device->os_dep.rsrc_start,
-+ dwc_otg_device->os_dep.base);
-+
-+ pci_set_master(_dev);
-+ pci_set_drvdata(_dev, dwc_otg_device);
-+#elif defined(PLATFORM_INTERFACE)
-+ DWC_DEBUGPL(DBG_ANY,"Platform resource: start=%08x, len=%08x\n",
-+ _dev->resource->start,
-+ _dev->resource->end - _dev->resource->start + 1);
-+#if 1
-+ if (!request_mem_region(_dev->resource[0].start,
-+ _dev->resource[0].end - _dev->resource[0].start + 1,
-+ "dwc_otg")) {
-+ dev_dbg(&_dev->dev, "error reserving mapped memory\n");
-+ retval = -EFAULT;
-+ goto fail;
-+ }
-+
-+ dwc_otg_device->os_dep.base = ioremap_nocache(_dev->resource[0].start,
-+ _dev->resource[0].end -
-+ _dev->resource[0].start+1);
-+ if (fiq_enable)
-+ {
-+ if (!request_mem_region(_dev->resource[1].start,
-+ _dev->resource[1].end - _dev->resource[1].start + 1,
-+ "dwc_otg")) {
-+ dev_dbg(&_dev->dev, "error reserving mapped memory\n");
-+ retval = -EFAULT;
-+ goto fail;
-+ }
-+
-+ dwc_otg_device->os_dep.mphi_base = ioremap_nocache(_dev->resource[1].start,
-+ _dev->resource[1].end -
-+ _dev->resource[1].start + 1);
-+ }
-+
-+#else
-+ {
-+ struct map_desc desc = {
-+ .virtual = IO_ADDRESS((unsigned)_dev->resource->start),
-+ .pfn = __phys_to_pfn((unsigned)_dev->resource->start),
-+ .length = SZ_128K,
-+ .type = MT_DEVICE
-+ };
-+ iotable_init(&desc, 1);
-+ dwc_otg_device->os_dep.base = (void *)desc.virtual;
-+ }
-+#endif
-+ if (!dwc_otg_device->os_dep.base) {
-+ dev_err(&_dev->dev, "ioremap() failed\n");
-+ retval = -ENOMEM;
-+ goto fail;
-+ }
-+ dev_dbg(&_dev->dev, "base=0x%08x\n",
-+ (unsigned)dwc_otg_device->os_dep.base);
-+#endif
-+
-+ /*
-+ * Initialize driver data to point to the global DWC_otg
-+ * Device structure.
-+ */
-+#ifdef LM_INTERFACE
-+ lm_set_drvdata(_dev, dwc_otg_device);
-+#elif defined(PLATFORM_INTERFACE)
-+ platform_set_drvdata(_dev, dwc_otg_device);
-+#endif
-+ dev_dbg(&_dev->dev, "dwc_otg_device=0x%p\n", dwc_otg_device);
-+
-+ dwc_otg_device->core_if = dwc_otg_cil_init(dwc_otg_device->os_dep.base);
-+ DWC_DEBUGPL(DBG_HCDV, "probe of device %p given core_if %p\n",
-+ dwc_otg_device, dwc_otg_device->core_if);//GRAYG
-+
-+ if (!dwc_otg_device->core_if) {
-+ dev_err(&_dev->dev, "CIL initialization failed!\n");
-+ retval = -ENOMEM;
-+ goto fail;
-+ }
-+
-+ dev_dbg(&_dev->dev, "Calling get_gsnpsid\n");
-+ /*
-+ * Attempt to ensure this device is really a DWC_otg Controller.
-+ * Read and verify the SNPSID register contents. The value should be
-+ * 0x45F42XXX or 0x45F42XXX, which corresponds to either "OT2" or "OTG3",
-+ * as in "OTG version 2.XX" or "OTG version 3.XX".
-+ */
-+
-+ if (((dwc_otg_get_gsnpsid(dwc_otg_device->core_if) & 0xFFFFF000) != 0x4F542000) &&
-+ ((dwc_otg_get_gsnpsid(dwc_otg_device->core_if) & 0xFFFFF000) != 0x4F543000)) {
-+ dev_err(&_dev->dev, "Bad value for SNPSID: 0x%08x\n",
-+ dwc_otg_get_gsnpsid(dwc_otg_device->core_if));
-+ retval = -EINVAL;
-+ goto fail;
-+ }
-+
-+ /*
-+ * Validate parameter values.
-+ */
-+ dev_dbg(&_dev->dev, "Calling set_parameters\n");
-+ if (set_parameters(dwc_otg_device->core_if)) {
-+ retval = -EINVAL;
-+ goto fail;
-+ }
-+
-+ /*
-+ * Create Device Attributes in sysfs
-+ */
-+ dev_dbg(&_dev->dev, "Calling attr_create\n");
-+ dwc_otg_attr_create(_dev);
-+
-+ /*
-+ * Disable the global interrupt until all the interrupt
-+ * handlers are installed.
-+ */
-+ dev_dbg(&_dev->dev, "Calling disable_global_interrupts\n");
-+ dwc_otg_disable_global_interrupts(dwc_otg_device->core_if);
-+
-+ /*
-+ * Install the interrupt handler for the common interrupts before
-+ * enabling common interrupts in core_init below.
-+ */
-+
-+#if defined(PLATFORM_INTERFACE)
-+ devirq = platform_get_irq(_dev, fiq_enable ? 0 : 1);
-+#else
-+ devirq = _dev->irq;
-+#endif
-+ DWC_DEBUGPL(DBG_CIL, "registering (common) handler for irq%d\n",
-+ devirq);
-+ dev_dbg(&_dev->dev, "Calling request_irq(%d)\n", devirq);
-+ retval = request_irq(devirq, dwc_otg_common_irq,
-+ IRQF_SHARED,
-+ "dwc_otg", dwc_otg_device);
-+ if (retval) {
-+ DWC_ERROR("request of irq%d failed\n", devirq);
-+ retval = -EBUSY;
-+ goto fail;
-+ } else {
-+ dwc_otg_device->common_irq_installed = 1;
-+ }
-+
-+#ifndef IRQF_TRIGGER_LOW
-+#if defined(LM_INTERFACE) || defined(PLATFORM_INTERFACE)
-+ dev_dbg(&_dev->dev, "Calling set_irq_type\n");
-+ set_irq_type(devirq,
-+#if (LINUX_VERSION_CODE < KERNEL_VERSION(2,6,30))
-+ IRQT_LOW
-+#else
-+ IRQ_TYPE_LEVEL_LOW
-+#endif
-+ );
-+#endif
-+#endif /*IRQF_TRIGGER_LOW*/
-+
-+ /*
-+ * Initialize the DWC_otg core.
-+ */
-+ dev_dbg(&_dev->dev, "Calling dwc_otg_core_init\n");
-+ dwc_otg_core_init(dwc_otg_device->core_if);
-+
-+#ifndef DWC_HOST_ONLY
-+ /*
-+ * Initialize the PCD
-+ */
-+ dev_dbg(&_dev->dev, "Calling pcd_init\n");
-+ retval = pcd_init(_dev);
-+ if (retval != 0) {
-+ DWC_ERROR("pcd_init failed\n");
-+ dwc_otg_device->pcd = NULL;
-+ goto fail;
-+ }
-+#endif
-+#ifndef DWC_DEVICE_ONLY
-+ /*
-+ * Initialize the HCD
-+ */
-+ dev_dbg(&_dev->dev, "Calling hcd_init\n");
-+ retval = hcd_init(_dev);
-+ if (retval != 0) {
-+ DWC_ERROR("hcd_init failed\n");
-+ dwc_otg_device->hcd = NULL;
-+ goto fail;
-+ }
-+#endif
-+ /* Recover from drvdata having been overwritten by hcd_init() */
-+#ifdef LM_INTERFACE
-+ lm_set_drvdata(_dev, dwc_otg_device);
-+#elif defined(PLATFORM_INTERFACE)
-+ platform_set_drvdata(_dev, dwc_otg_device);
-+#elif defined(PCI_INTERFACE)
-+ pci_set_drvdata(_dev, dwc_otg_device);
-+ dwc_otg_device->os_dep.pcidev = _dev;
-+#endif
-+
-+ /*
-+ * Enable the global interrupt after all the interrupt
-+ * handlers are installed if there is no ADP support else
-+ * perform initial actions required for Internal ADP logic.
-+ */
-+ if (!dwc_otg_get_param_adp_enable(dwc_otg_device->core_if)) {
-+ dev_dbg(&_dev->dev, "Calling enable_global_interrupts\n");
-+ dwc_otg_enable_global_interrupts(dwc_otg_device->core_if);
-+ dev_dbg(&_dev->dev, "Done\n");
-+ } else
-+ dwc_otg_adp_start(dwc_otg_device->core_if,
-+ dwc_otg_is_host_mode(dwc_otg_device->core_if));
-+
-+ return 0;
-+
-+fail:
-+ dwc_otg_driver_remove(_dev);
-+ return retval;
-+}
-+
-+/**
-+ * This structure defines the methods to be called by a bus driver
-+ * during the lifecycle of a device on that bus. Both drivers and
-+ * devices are registered with a bus driver. The bus driver matches
-+ * devices to drivers based on information in the device and driver
-+ * structures.
-+ *
-+ * The probe function is called when the bus driver matches a device
-+ * to this driver. The remove function is called when a device is
-+ * unregistered with the bus driver.
-+ */
-+#ifdef LM_INTERFACE
-+static struct lm_driver dwc_otg_driver = {
-+ .drv = {.name = (char *)dwc_driver_name,},
-+ .probe = dwc_otg_driver_probe,
-+ .remove = dwc_otg_driver_remove,
-+ // 'suspend' and 'resume' absent
-+};
-+#elif defined(PCI_INTERFACE)
-+static const struct pci_device_id pci_ids[] = { {
-+ PCI_DEVICE(0x16c3, 0xabcd),
-+ .driver_data =
-+ (unsigned long)0xdeadbeef,
-+ }, { /* end: all zeroes */ }
-+};
-+
-+MODULE_DEVICE_TABLE(pci, pci_ids);
-+
-+/* pci driver glue; this is a "new style" PCI driver module */
-+static struct pci_driver dwc_otg_driver = {
-+ .name = "dwc_otg",
-+ .id_table = pci_ids,
-+
-+ .probe = dwc_otg_driver_probe,
-+ .remove = dwc_otg_driver_remove,
-+
-+ .driver = {
-+ .name = (char *)dwc_driver_name,
-+ },
-+};
-+#elif defined(PLATFORM_INTERFACE)
-+static struct platform_device_id platform_ids[] = {
-+ {
-+ .name = "bcm2708_usb",
-+ .driver_data = (kernel_ulong_t) 0xdeadbeef,
-+ },
-+ { /* end: all zeroes */ }
-+};
-+MODULE_DEVICE_TABLE(platform, platform_ids);
-+
-+static const struct of_device_id dwc_otg_of_match_table[] = {
-+ { .compatible = "brcm,bcm2708-usb", },
-+ {},
-+};
-+MODULE_DEVICE_TABLE(of, dwc_otg_of_match_table);
-+
-+static struct platform_driver dwc_otg_driver = {
-+ .driver = {
-+ .name = (char *)dwc_driver_name,
-+ .of_match_table = dwc_otg_of_match_table,
-+ },
-+ .id_table = platform_ids,
-+
-+ .probe = dwc_otg_driver_probe,
-+ .remove = dwc_otg_driver_remove,
-+ // no 'shutdown', 'suspend', 'resume', 'suspend_late' or 'resume_early'
-+};
-+#endif
-+
-+/**
-+ * This function is called when the dwc_otg_driver is installed with the
-+ * insmod command. It registers the dwc_otg_driver structure with the
-+ * appropriate bus driver. This will cause the dwc_otg_driver_probe function
-+ * to be called. In addition, the bus driver will automatically expose
-+ * attributes defined for the device and driver in the special sysfs file
-+ * system.
-+ *
-+ * @return
-+ */
-+static int __init dwc_otg_driver_init(void)
-+{
-+ int retval = 0;
-+ int error;
-+ struct device_driver *drv;
-+
-+ if(fiq_fsm_enable && !fiq_enable) {
-+ printk(KERN_WARNING "dwc_otg: fiq_fsm_enable was set without fiq_enable! Correcting.\n");
-+ fiq_enable = 1;
-+ }
-+
-+ printk(KERN_INFO "%s: version %s (%s bus)\n", dwc_driver_name,
-+ DWC_DRIVER_VERSION,
-+#ifdef LM_INTERFACE
-+ "logicmodule");
-+ retval = lm_driver_register(&dwc_otg_driver);
-+ drv = &dwc_otg_driver.drv;
-+#elif defined(PCI_INTERFACE)
-+ "pci");
-+ retval = pci_register_driver(&dwc_otg_driver);
-+ drv = &dwc_otg_driver.driver;
-+#elif defined(PLATFORM_INTERFACE)
-+ "platform");
-+ retval = platform_driver_register(&dwc_otg_driver);
-+ drv = &dwc_otg_driver.driver;
-+#endif
-+ if (retval < 0) {
-+ printk(KERN_ERR "%s retval=%d\n", __func__, retval);
-+ return retval;
-+ }
-+ printk(KERN_DEBUG "dwc_otg: FIQ %s\n", fiq_enable ? "enabled":"disabled");
-+ printk(KERN_DEBUG "dwc_otg: NAK holdoff %s\n", nak_holdoff ? "enabled":"disabled");
-+ printk(KERN_DEBUG "dwc_otg: FIQ split-transaction FSM %s\n", fiq_fsm_enable ? "enabled":"disabled");
-+
-+ error = driver_create_file(drv, &driver_attr_version);
-+#ifdef DEBUG
-+ error = driver_create_file(drv, &driver_attr_debuglevel);
-+#endif
-+ return retval;
-+}
-+
-+module_init(dwc_otg_driver_init);
-+
-+/**
-+ * This function is called when the driver is removed from the kernel
-+ * with the rmmod command. The driver unregisters itself with its bus
-+ * driver.
-+ *
-+ */
-+static void __exit dwc_otg_driver_cleanup(void)
-+{
-+ printk(KERN_DEBUG "dwc_otg_driver_cleanup()\n");
-+
-+#ifdef LM_INTERFACE
-+ driver_remove_file(&dwc_otg_driver.drv, &driver_attr_debuglevel);
-+ driver_remove_file(&dwc_otg_driver.drv, &driver_attr_version);
-+ lm_driver_unregister(&dwc_otg_driver);
-+#elif defined(PCI_INTERFACE)
-+ driver_remove_file(&dwc_otg_driver.driver, &driver_attr_debuglevel);
-+ driver_remove_file(&dwc_otg_driver.driver, &driver_attr_version);
-+ pci_unregister_driver(&dwc_otg_driver);
-+#elif defined(PLATFORM_INTERFACE)
-+ driver_remove_file(&dwc_otg_driver.driver, &driver_attr_debuglevel);
-+ driver_remove_file(&dwc_otg_driver.driver, &driver_attr_version);
-+ platform_driver_unregister(&dwc_otg_driver);
-+#endif
-+
-+ printk(KERN_INFO "%s module removed\n", dwc_driver_name);
-+}
-+
-+module_exit(dwc_otg_driver_cleanup);
-+
-+MODULE_DESCRIPTION(DWC_DRIVER_DESC);
-+MODULE_AUTHOR("Synopsys Inc.");
-+MODULE_LICENSE("GPL");
-+
-+module_param_named(otg_cap, dwc_otg_module_params.otg_cap, int, 0444);
-+MODULE_PARM_DESC(otg_cap, "OTG Capabilities 0=HNP&SRP 1=SRP Only 2=None");
-+module_param_named(opt, dwc_otg_module_params.opt, int, 0444);
-+MODULE_PARM_DESC(opt, "OPT Mode");
-+module_param_named(dma_enable, dwc_otg_module_params.dma_enable, int, 0444);
-+MODULE_PARM_DESC(dma_enable, "DMA Mode 0=Slave 1=DMA enabled");
-+
-+module_param_named(dma_desc_enable, dwc_otg_module_params.dma_desc_enable, int,
-+ 0444);
-+MODULE_PARM_DESC(dma_desc_enable,
-+ "DMA Desc Mode 0=Address DMA 1=DMA Descriptor enabled");
-+
-+module_param_named(dma_burst_size, dwc_otg_module_params.dma_burst_size, int,
-+ 0444);
-+MODULE_PARM_DESC(dma_burst_size,
-+ "DMA Burst Size 1, 4, 8, 16, 32, 64, 128, 256");
-+module_param_named(speed, dwc_otg_module_params.speed, int, 0444);
-+MODULE_PARM_DESC(speed, "Speed 0=High Speed 1=Full Speed");
-+module_param_named(host_support_fs_ls_low_power,
-+ dwc_otg_module_params.host_support_fs_ls_low_power, int,
-+ 0444);
-+MODULE_PARM_DESC(host_support_fs_ls_low_power,
-+ "Support Low Power w/FS or LS 0=Support 1=Don't Support");
-+module_param_named(host_ls_low_power_phy_clk,
-+ dwc_otg_module_params.host_ls_low_power_phy_clk, int, 0444);
-+MODULE_PARM_DESC(host_ls_low_power_phy_clk,
-+ "Low Speed Low Power Clock 0=48Mhz 1=6Mhz");
-+module_param_named(enable_dynamic_fifo,
-+ dwc_otg_module_params.enable_dynamic_fifo, int, 0444);
-+MODULE_PARM_DESC(enable_dynamic_fifo, "0=cC Setting 1=Allow Dynamic Sizing");
-+module_param_named(data_fifo_size, dwc_otg_module_params.data_fifo_size, int,
-+ 0444);
-+MODULE_PARM_DESC(data_fifo_size,
-+ "Total number of words in the data FIFO memory 32-32768");
-+module_param_named(dev_rx_fifo_size, dwc_otg_module_params.dev_rx_fifo_size,
-+ int, 0444);
-+MODULE_PARM_DESC(dev_rx_fifo_size, "Number of words in the Rx FIFO 16-32768");
-+module_param_named(dev_nperio_tx_fifo_size,
-+ dwc_otg_module_params.dev_nperio_tx_fifo_size, int, 0444);
-+MODULE_PARM_DESC(dev_nperio_tx_fifo_size,
-+ "Number of words in the non-periodic Tx FIFO 16-32768");
-+module_param_named(dev_perio_tx_fifo_size_1,
-+ dwc_otg_module_params.dev_perio_tx_fifo_size[0], int, 0444);
-+MODULE_PARM_DESC(dev_perio_tx_fifo_size_1,
-+ "Number of words in the periodic Tx FIFO 4-768");
-+module_param_named(dev_perio_tx_fifo_size_2,
-+ dwc_otg_module_params.dev_perio_tx_fifo_size[1], int, 0444);
-+MODULE_PARM_DESC(dev_perio_tx_fifo_size_2,
-+ "Number of words in the periodic Tx FIFO 4-768");
-+module_param_named(dev_perio_tx_fifo_size_3,
-+ dwc_otg_module_params.dev_perio_tx_fifo_size[2], int, 0444);
-+MODULE_PARM_DESC(dev_perio_tx_fifo_size_3,
-+ "Number of words in the periodic Tx FIFO 4-768");
-+module_param_named(dev_perio_tx_fifo_size_4,
-+ dwc_otg_module_params.dev_perio_tx_fifo_size[3], int, 0444);
-+MODULE_PARM_DESC(dev_perio_tx_fifo_size_4,
-+ "Number of words in the periodic Tx FIFO 4-768");
-+module_param_named(dev_perio_tx_fifo_size_5,
-+ dwc_otg_module_params.dev_perio_tx_fifo_size[4], int, 0444);
-+MODULE_PARM_DESC(dev_perio_tx_fifo_size_5,
-+ "Number of words in the periodic Tx FIFO 4-768");
-+module_param_named(dev_perio_tx_fifo_size_6,
-+ dwc_otg_module_params.dev_perio_tx_fifo_size[5], int, 0444);
-+MODULE_PARM_DESC(dev_perio_tx_fifo_size_6,
-+ "Number of words in the periodic Tx FIFO 4-768");
-+module_param_named(dev_perio_tx_fifo_size_7,
-+ dwc_otg_module_params.dev_perio_tx_fifo_size[6], int, 0444);
-+MODULE_PARM_DESC(dev_perio_tx_fifo_size_7,
-+ "Number of words in the periodic Tx FIFO 4-768");
-+module_param_named(dev_perio_tx_fifo_size_8,
-+ dwc_otg_module_params.dev_perio_tx_fifo_size[7], int, 0444);
-+MODULE_PARM_DESC(dev_perio_tx_fifo_size_8,
-+ "Number of words in the periodic Tx FIFO 4-768");
-+module_param_named(dev_perio_tx_fifo_size_9,
-+ dwc_otg_module_params.dev_perio_tx_fifo_size[8], int, 0444);
-+MODULE_PARM_DESC(dev_perio_tx_fifo_size_9,
-+ "Number of words in the periodic Tx FIFO 4-768");
-+module_param_named(dev_perio_tx_fifo_size_10,
-+ dwc_otg_module_params.dev_perio_tx_fifo_size[9], int, 0444);
-+MODULE_PARM_DESC(dev_perio_tx_fifo_size_10,
-+ "Number of words in the periodic Tx FIFO 4-768");
-+module_param_named(dev_perio_tx_fifo_size_11,
-+ dwc_otg_module_params.dev_perio_tx_fifo_size[10], int, 0444);
-+MODULE_PARM_DESC(dev_perio_tx_fifo_size_11,
-+ "Number of words in the periodic Tx FIFO 4-768");
-+module_param_named(dev_perio_tx_fifo_size_12,
-+ dwc_otg_module_params.dev_perio_tx_fifo_size[11], int, 0444);
-+MODULE_PARM_DESC(dev_perio_tx_fifo_size_12,
-+ "Number of words in the periodic Tx FIFO 4-768");
-+module_param_named(dev_perio_tx_fifo_size_13,
-+ dwc_otg_module_params.dev_perio_tx_fifo_size[12], int, 0444);
-+MODULE_PARM_DESC(dev_perio_tx_fifo_size_13,
-+ "Number of words in the periodic Tx FIFO 4-768");
-+module_param_named(dev_perio_tx_fifo_size_14,
-+ dwc_otg_module_params.dev_perio_tx_fifo_size[13], int, 0444);
-+MODULE_PARM_DESC(dev_perio_tx_fifo_size_14,
-+ "Number of words in the periodic Tx FIFO 4-768");
-+module_param_named(dev_perio_tx_fifo_size_15,
-+ dwc_otg_module_params.dev_perio_tx_fifo_size[14], int, 0444);
-+MODULE_PARM_DESC(dev_perio_tx_fifo_size_15,
-+ "Number of words in the periodic Tx FIFO 4-768");
-+module_param_named(host_rx_fifo_size, dwc_otg_module_params.host_rx_fifo_size,
-+ int, 0444);
-+MODULE_PARM_DESC(host_rx_fifo_size, "Number of words in the Rx FIFO 16-32768");
-+module_param_named(host_nperio_tx_fifo_size,
-+ dwc_otg_module_params.host_nperio_tx_fifo_size, int, 0444);
-+MODULE_PARM_DESC(host_nperio_tx_fifo_size,
-+ "Number of words in the non-periodic Tx FIFO 16-32768");
-+module_param_named(host_perio_tx_fifo_size,
-+ dwc_otg_module_params.host_perio_tx_fifo_size, int, 0444);
-+MODULE_PARM_DESC(host_perio_tx_fifo_size,
-+ "Number of words in the host periodic Tx FIFO 16-32768");
-+module_param_named(max_transfer_size, dwc_otg_module_params.max_transfer_size,
-+ int, 0444);
-+/** @todo Set the max to 512K, modify checks */
-+MODULE_PARM_DESC(max_transfer_size,
-+ "The maximum transfer size supported in bytes 2047-65535");
-+module_param_named(max_packet_count, dwc_otg_module_params.max_packet_count,
-+ int, 0444);
-+MODULE_PARM_DESC(max_packet_count,
-+ "The maximum number of packets in a transfer 15-511");
-+module_param_named(host_channels, dwc_otg_module_params.host_channels, int,
-+ 0444);
-+MODULE_PARM_DESC(host_channels,
-+ "The number of host channel registers to use 1-16");
-+module_param_named(dev_endpoints, dwc_otg_module_params.dev_endpoints, int,
-+ 0444);
-+MODULE_PARM_DESC(dev_endpoints,
-+ "The number of endpoints in addition to EP0 available for device mode 1-15");
-+module_param_named(phy_type, dwc_otg_module_params.phy_type, int, 0444);
-+MODULE_PARM_DESC(phy_type, "0=Reserved 1=UTMI+ 2=ULPI");
-+module_param_named(phy_utmi_width, dwc_otg_module_params.phy_utmi_width, int,
-+ 0444);
-+MODULE_PARM_DESC(phy_utmi_width, "Specifies the UTMI+ Data Width 8 or 16 bits");
-+module_param_named(phy_ulpi_ddr, dwc_otg_module_params.phy_ulpi_ddr, int, 0444);
-+MODULE_PARM_DESC(phy_ulpi_ddr,
-+ "ULPI at double or single data rate 0=Single 1=Double");
-+module_param_named(phy_ulpi_ext_vbus, dwc_otg_module_params.phy_ulpi_ext_vbus,
-+ int, 0444);
-+MODULE_PARM_DESC(phy_ulpi_ext_vbus,
-+ "ULPI PHY using internal or external vbus 0=Internal");
-+module_param_named(i2c_enable, dwc_otg_module_params.i2c_enable, int, 0444);
-+MODULE_PARM_DESC(i2c_enable, "FS PHY Interface");
-+module_param_named(ulpi_fs_ls, dwc_otg_module_params.ulpi_fs_ls, int, 0444);
-+MODULE_PARM_DESC(ulpi_fs_ls, "ULPI PHY FS/LS mode only");
-+module_param_named(ts_dline, dwc_otg_module_params.ts_dline, int, 0444);
-+MODULE_PARM_DESC(ts_dline, "Term select Dline pulsing for all PHYs");
-+module_param_named(debug, g_dbg_lvl, int, 0444);
-+MODULE_PARM_DESC(debug, "");
-+
-+module_param_named(en_multiple_tx_fifo,
-+ dwc_otg_module_params.en_multiple_tx_fifo, int, 0444);
-+MODULE_PARM_DESC(en_multiple_tx_fifo,
-+ "Dedicated Non Periodic Tx FIFOs 0=disabled 1=enabled");
-+module_param_named(dev_tx_fifo_size_1,
-+ dwc_otg_module_params.dev_tx_fifo_size[0], int, 0444);
-+MODULE_PARM_DESC(dev_tx_fifo_size_1, "Number of words in the Tx FIFO 4-768");
-+module_param_named(dev_tx_fifo_size_2,
-+ dwc_otg_module_params.dev_tx_fifo_size[1], int, 0444);
-+MODULE_PARM_DESC(dev_tx_fifo_size_2, "Number of words in the Tx FIFO 4-768");
-+module_param_named(dev_tx_fifo_size_3,
-+ dwc_otg_module_params.dev_tx_fifo_size[2], int, 0444);
-+MODULE_PARM_DESC(dev_tx_fifo_size_3, "Number of words in the Tx FIFO 4-768");
-+module_param_named(dev_tx_fifo_size_4,
-+ dwc_otg_module_params.dev_tx_fifo_size[3], int, 0444);
-+MODULE_PARM_DESC(dev_tx_fifo_size_4, "Number of words in the Tx FIFO 4-768");
-+module_param_named(dev_tx_fifo_size_5,
-+ dwc_otg_module_params.dev_tx_fifo_size[4], int, 0444);
-+MODULE_PARM_DESC(dev_tx_fifo_size_5, "Number of words in the Tx FIFO 4-768");
-+module_param_named(dev_tx_fifo_size_6,
-+ dwc_otg_module_params.dev_tx_fifo_size[5], int, 0444);
-+MODULE_PARM_DESC(dev_tx_fifo_size_6, "Number of words in the Tx FIFO 4-768");
-+module_param_named(dev_tx_fifo_size_7,
-+ dwc_otg_module_params.dev_tx_fifo_size[6], int, 0444);
-+MODULE_PARM_DESC(dev_tx_fifo_size_7, "Number of words in the Tx FIFO 4-768");
-+module_param_named(dev_tx_fifo_size_8,
-+ dwc_otg_module_params.dev_tx_fifo_size[7], int, 0444);
-+MODULE_PARM_DESC(dev_tx_fifo_size_8, "Number of words in the Tx FIFO 4-768");
-+module_param_named(dev_tx_fifo_size_9,
-+ dwc_otg_module_params.dev_tx_fifo_size[8], int, 0444);
-+MODULE_PARM_DESC(dev_tx_fifo_size_9, "Number of words in the Tx FIFO 4-768");
-+module_param_named(dev_tx_fifo_size_10,
-+ dwc_otg_module_params.dev_tx_fifo_size[9], int, 0444);
-+MODULE_PARM_DESC(dev_tx_fifo_size_10, "Number of words in the Tx FIFO 4-768");
-+module_param_named(dev_tx_fifo_size_11,
-+ dwc_otg_module_params.dev_tx_fifo_size[10], int, 0444);
-+MODULE_PARM_DESC(dev_tx_fifo_size_11, "Number of words in the Tx FIFO 4-768");
-+module_param_named(dev_tx_fifo_size_12,
-+ dwc_otg_module_params.dev_tx_fifo_size[11], int, 0444);
-+MODULE_PARM_DESC(dev_tx_fifo_size_12, "Number of words in the Tx FIFO 4-768");
-+module_param_named(dev_tx_fifo_size_13,
-+ dwc_otg_module_params.dev_tx_fifo_size[12], int, 0444);
-+MODULE_PARM_DESC(dev_tx_fifo_size_13, "Number of words in the Tx FIFO 4-768");
-+module_param_named(dev_tx_fifo_size_14,
-+ dwc_otg_module_params.dev_tx_fifo_size[13], int, 0444);
-+MODULE_PARM_DESC(dev_tx_fifo_size_14, "Number of words in the Tx FIFO 4-768");
-+module_param_named(dev_tx_fifo_size_15,
-+ dwc_otg_module_params.dev_tx_fifo_size[14], int, 0444);
-+MODULE_PARM_DESC(dev_tx_fifo_size_15, "Number of words in the Tx FIFO 4-768");
-+
-+module_param_named(thr_ctl, dwc_otg_module_params.thr_ctl, int, 0444);
-+MODULE_PARM_DESC(thr_ctl,
-+ "Thresholding enable flag bit 0 - non ISO Tx thr., 1 - ISO Tx thr., 2 - Rx thr.- bit 0=disabled 1=enabled");
-+module_param_named(tx_thr_length, dwc_otg_module_params.tx_thr_length, int,
-+ 0444);
-+MODULE_PARM_DESC(tx_thr_length, "Tx Threshold length in 32 bit DWORDs");
-+module_param_named(rx_thr_length, dwc_otg_module_params.rx_thr_length, int,
-+ 0444);
-+MODULE_PARM_DESC(rx_thr_length, "Rx Threshold length in 32 bit DWORDs");
-+
-+module_param_named(pti_enable, dwc_otg_module_params.pti_enable, int, 0444);
-+module_param_named(mpi_enable, dwc_otg_module_params.mpi_enable, int, 0444);
-+module_param_named(lpm_enable, dwc_otg_module_params.lpm_enable, int, 0444);
-+MODULE_PARM_DESC(lpm_enable, "LPM Enable 0=LPM Disabled 1=LPM Enabled");
-+module_param_named(ic_usb_cap, dwc_otg_module_params.ic_usb_cap, int, 0444);
-+MODULE_PARM_DESC(ic_usb_cap,
-+ "IC_USB Capability 0=IC_USB Disabled 1=IC_USB Enabled");
-+module_param_named(ahb_thr_ratio, dwc_otg_module_params.ahb_thr_ratio, int,
-+ 0444);
-+MODULE_PARM_DESC(ahb_thr_ratio, "AHB Threshold Ratio");
-+module_param_named(power_down, dwc_otg_module_params.power_down, int, 0444);
-+MODULE_PARM_DESC(power_down, "Power Down Mode");
-+module_param_named(reload_ctl, dwc_otg_module_params.reload_ctl, int, 0444);
-+MODULE_PARM_DESC(reload_ctl, "HFIR Reload Control");
-+module_param_named(dev_out_nak, dwc_otg_module_params.dev_out_nak, int, 0444);
-+MODULE_PARM_DESC(dev_out_nak, "Enable Device OUT NAK");
-+module_param_named(cont_on_bna, dwc_otg_module_params.cont_on_bna, int, 0444);
-+MODULE_PARM_DESC(cont_on_bna, "Enable Enable Continue on BNA");
-+module_param_named(ahb_single, dwc_otg_module_params.ahb_single, int, 0444);
-+MODULE_PARM_DESC(ahb_single, "Enable AHB Single Support");
-+module_param_named(adp_enable, dwc_otg_module_params.adp_enable, int, 0444);
-+MODULE_PARM_DESC(adp_enable, "ADP Enable 0=ADP Disabled 1=ADP Enabled");
-+module_param_named(otg_ver, dwc_otg_module_params.otg_ver, int, 0444);
-+MODULE_PARM_DESC(otg_ver, "OTG revision supported 0=OTG 1.3 1=OTG 2.0");
-+module_param(microframe_schedule, bool, 0444);
-+MODULE_PARM_DESC(microframe_schedule, "Enable the microframe scheduler");
-+
-+module_param(fiq_enable, bool, 0444);
-+MODULE_PARM_DESC(fiq_enable, "Enable the FIQ");
-+module_param(nak_holdoff, ushort, 0644);
-+MODULE_PARM_DESC(nak_holdoff, "Throttle duration for bulk split-transaction endpoints on a NAK. Default 8");
-+module_param(fiq_fsm_enable, bool, 0444);
-+MODULE_PARM_DESC(fiq_fsm_enable, "Enable the FIQ to perform split transactions as defined by fiq_fsm_mask");
-+module_param(fiq_fsm_mask, ushort, 0444);
-+MODULE_PARM_DESC(fiq_fsm_mask, "Bitmask of transactions to perform in the FIQ.\n"
-+ "Bit 0 : Non-periodic split transactions\n"
-+ "Bit 1 : Periodic split transactions\n"
-+ "Bit 2 : High-speed multi-transfer isochronous\n"
-+ "All other bits should be set 0.");
-+
-+
-+/** @page "Module Parameters"
-+ *
-+ * The following parameters may be specified when starting the module.
-+ * These parameters define how the DWC_otg controller should be
-+ * configured. Parameter values are passed to the CIL initialization
-+ * function dwc_otg_cil_init
-+ *
-+ * Example: <code>modprobe dwc_otg speed=1 otg_cap=1</code>
-+ *
-+
-+ <table>
-+ <tr><td>Parameter Name</td><td>Meaning</td></tr>
-+
-+ <tr>
-+ <td>otg_cap</td>
-+ <td>Specifies the OTG capabilities. The driver will automatically detect the
-+ value for this parameter if none is specified.
-+ - 0: HNP and SRP capable (default, if available)
-+ - 1: SRP Only capable
-+ - 2: No HNP/SRP capable
-+ </td></tr>
-+
-+ <tr>
-+ <td>dma_enable</td>
-+ <td>Specifies whether to use slave or DMA mode for accessing the data FIFOs.
-+ The driver will automatically detect the value for this parameter if none is
-+ specified.
-+ - 0: Slave
-+ - 1: DMA (default, if available)
-+ </td></tr>
-+
-+ <tr>
-+ <td>dma_burst_size</td>
-+ <td>The DMA Burst size (applicable only for External DMA Mode).
-+ - Values: 1, 4, 8 16, 32, 64, 128, 256 (default 32)
-+ </td></tr>
-+
-+ <tr>
-+ <td>speed</td>
-+ <td>Specifies the maximum speed of operation in host and device mode. The
-+ actual speed depends on the speed of the attached device and the value of
-+ phy_type.
-+ - 0: High Speed (default)
-+ - 1: Full Speed
-+ </td></tr>
-+
-+ <tr>
-+ <td>host_support_fs_ls_low_power</td>
-+ <td>Specifies whether low power mode is supported when attached to a Full
-+ Speed or Low Speed device in host mode.
-+ - 0: Don't support low power mode (default)
-+ - 1: Support low power mode
-+ </td></tr>
-+
-+ <tr>
-+ <td>host_ls_low_power_phy_clk</td>
-+ <td>Specifies the PHY clock rate in low power mode when connected to a Low
-+ Speed device in host mode. This parameter is applicable only if
-+ HOST_SUPPORT_FS_LS_LOW_POWER is enabled.
-+ - 0: 48 MHz (default)
-+ - 1: 6 MHz
-+ </td></tr>
-+
-+ <tr>
-+ <td>enable_dynamic_fifo</td>
-+ <td> Specifies whether FIFOs may be resized by the driver software.
-+ - 0: Use cC FIFO size parameters
-+ - 1: Allow dynamic FIFO sizing (default)
-+ </td></tr>
-+
-+ <tr>
-+ <td>data_fifo_size</td>
-+ <td>Total number of 4-byte words in the data FIFO memory. This memory
-+ includes the Rx FIFO, non-periodic Tx FIFO, and periodic Tx FIFOs.
-+ - Values: 32 to 32768 (default 8192)
-+
-+ Note: The total FIFO memory depth in the FPGA configuration is 8192.
-+ </td></tr>
-+
-+ <tr>
-+ <td>dev_rx_fifo_size</td>
-+ <td>Number of 4-byte words in the Rx FIFO in device mode when dynamic
-+ FIFO sizing is enabled.
-+ - Values: 16 to 32768 (default 1064)
-+ </td></tr>
-+
-+ <tr>
-+ <td>dev_nperio_tx_fifo_size</td>
-+ <td>Number of 4-byte words in the non-periodic Tx FIFO in device mode when
-+ dynamic FIFO sizing is enabled.
-+ - Values: 16 to 32768 (default 1024)
-+ </td></tr>
-+
-+ <tr>
-+ <td>dev_perio_tx_fifo_size_n (n = 1 to 15)</td>
-+ <td>Number of 4-byte words in each of the periodic Tx FIFOs in device mode
-+ when dynamic FIFO sizing is enabled.
-+ - Values: 4 to 768 (default 256)
-+ </td></tr>
-+
-+ <tr>
-+ <td>host_rx_fifo_size</td>
-+ <td>Number of 4-byte words in the Rx FIFO in host mode when dynamic FIFO
-+ sizing is enabled.
-+ - Values: 16 to 32768 (default 1024)
-+ </td></tr>
-+
-+ <tr>
-+ <td>host_nperio_tx_fifo_size</td>
-+ <td>Number of 4-byte words in the non-periodic Tx FIFO in host mode when
-+ dynamic FIFO sizing is enabled in the core.
-+ - Values: 16 to 32768 (default 1024)
-+ </td></tr>
-+
-+ <tr>
-+ <td>host_perio_tx_fifo_size</td>
-+ <td>Number of 4-byte words in the host periodic Tx FIFO when dynamic FIFO
-+ sizing is enabled.
-+ - Values: 16 to 32768 (default 1024)
-+ </td></tr>
-+
-+ <tr>
-+ <td>max_transfer_size</td>
-+ <td>The maximum transfer size supported in bytes.
-+ - Values: 2047 to 65,535 (default 65,535)
-+ </td></tr>
-+
-+ <tr>
-+ <td>max_packet_count</td>
-+ <td>The maximum number of packets in a transfer.
-+ - Values: 15 to 511 (default 511)
-+ </td></tr>
-+
-+ <tr>
-+ <td>host_channels</td>
-+ <td>The number of host channel registers to use.
-+ - Values: 1 to 16 (default 12)
-+
-+ Note: The FPGA configuration supports a maximum of 12 host channels.
-+ </td></tr>
-+
-+ <tr>
-+ <td>dev_endpoints</td>
-+ <td>The number of endpoints in addition to EP0 available for device mode
-+ operations.
-+ - Values: 1 to 15 (default 6 IN and OUT)
-+
-+ Note: The FPGA configuration supports a maximum of 6 IN and OUT endpoints in
-+ addition to EP0.
-+ </td></tr>
-+
-+ <tr>
-+ <td>phy_type</td>
-+ <td>Specifies the type of PHY interface to use. By default, the driver will
-+ automatically detect the phy_type.
-+ - 0: Full Speed
-+ - 1: UTMI+ (default, if available)
-+ - 2: ULPI
-+ </td></tr>
-+
-+ <tr>
-+ <td>phy_utmi_width</td>
-+ <td>Specifies the UTMI+ Data Width. This parameter is applicable for a
-+ phy_type of UTMI+. Also, this parameter is applicable only if the
-+ OTG_HSPHY_WIDTH cC parameter was set to "8 and 16 bits", meaning that the
-+ core has been configured to work at either data path width.
-+ - Values: 8 or 16 bits (default 16)
-+ </td></tr>
-+
-+ <tr>
-+ <td>phy_ulpi_ddr</td>
-+ <td>Specifies whether the ULPI operates at double or single data rate. This
-+ parameter is only applicable if phy_type is ULPI.
-+ - 0: single data rate ULPI interface with 8 bit wide data bus (default)
-+ - 1: double data rate ULPI interface with 4 bit wide data bus
-+ </td></tr>
-+
-+ <tr>
-+ <td>i2c_enable</td>
-+ <td>Specifies whether to use the I2C interface for full speed PHY. This
-+ parameter is only applicable if PHY_TYPE is FS.
-+ - 0: Disabled (default)
-+ - 1: Enabled
-+ </td></tr>
-+
-+ <tr>
-+ <td>ulpi_fs_ls</td>
-+ <td>Specifies whether to use ULPI FS/LS mode only.
-+ - 0: Disabled (default)
-+ - 1: Enabled
-+ </td></tr>
-+
-+ <tr>
-+ <td>ts_dline</td>
-+ <td>Specifies whether term select D-Line pulsing for all PHYs is enabled.
-+ - 0: Disabled (default)
-+ - 1: Enabled
-+ </td></tr>
-+
-+ <tr>
-+ <td>en_multiple_tx_fifo</td>
-+ <td>Specifies whether dedicatedto tx fifos are enabled for non periodic IN EPs.
-+ The driver will automatically detect the value for this parameter if none is
-+ specified.
-+ - 0: Disabled
-+ - 1: Enabled (default, if available)
-+ </td></tr>
-+
-+ <tr>
-+ <td>dev_tx_fifo_size_n (n = 1 to 15)</td>
-+ <td>Number of 4-byte words in each of the Tx FIFOs in device mode
-+ when dynamic FIFO sizing is enabled.
-+ - Values: 4 to 768 (default 256)
-+ </td></tr>
-+
-+ <tr>
-+ <td>tx_thr_length</td>
-+ <td>Transmit Threshold length in 32 bit double words
-+ - Values: 8 to 128 (default 64)
-+ </td></tr>
-+
-+ <tr>
-+ <td>rx_thr_length</td>
-+ <td>Receive Threshold length in 32 bit double words
-+ - Values: 8 to 128 (default 64)
-+ </td></tr>
-+
-+<tr>
-+ <td>thr_ctl</td>
-+ <td>Specifies whether to enable Thresholding for Device mode. Bits 0, 1, 2 of
-+ this parmater specifies if thresholding is enabled for non-Iso Tx, Iso Tx and
-+ Rx transfers accordingly.
-+ The driver will automatically detect the value for this parameter if none is
-+ specified.
-+ - Values: 0 to 7 (default 0)
-+ Bit values indicate:
-+ - 0: Thresholding disabled
-+ - 1: Thresholding enabled
-+ </td></tr>
-+
-+<tr>
-+ <td>dma_desc_enable</td>
-+ <td>Specifies whether to enable Descriptor DMA mode.
-+ The driver will automatically detect the value for this parameter if none is
-+ specified.
-+ - 0: Descriptor DMA disabled
-+ - 1: Descriptor DMA (default, if available)
-+ </td></tr>
-+
-+<tr>
-+ <td>mpi_enable</td>
-+ <td>Specifies whether to enable MPI enhancement mode.
-+ The driver will automatically detect the value for this parameter if none is
-+ specified.
-+ - 0: MPI disabled (default)
-+ - 1: MPI enable
-+ </td></tr>
-+
-+<tr>
-+ <td>pti_enable</td>
-+ <td>Specifies whether to enable PTI enhancement support.
-+ The driver will automatically detect the value for this parameter if none is
-+ specified.
-+ - 0: PTI disabled (default)
-+ - 1: PTI enable
-+ </td></tr>
-+
-+<tr>
-+ <td>lpm_enable</td>
-+ <td>Specifies whether to enable LPM support.
-+ The driver will automatically detect the value for this parameter if none is
-+ specified.
-+ - 0: LPM disabled
-+ - 1: LPM enable (default, if available)
-+ </td></tr>
-+
-+<tr>
-+ <td>ic_usb_cap</td>
-+ <td>Specifies whether to enable IC_USB capability.
-+ The driver will automatically detect the value for this parameter if none is
-+ specified.
-+ - 0: IC_USB disabled (default, if available)
-+ - 1: IC_USB enable
-+ </td></tr>
-+
-+<tr>
-+ <td>ahb_thr_ratio</td>
-+ <td>Specifies AHB Threshold ratio.
-+ - Values: 0 to 3 (default 0)
-+ </td></tr>
-+
-+<tr>
-+ <td>power_down</td>
-+ <td>Specifies Power Down(Hibernation) Mode.
-+ The driver will automatically detect the value for this parameter if none is
-+ specified.
-+ - 0: Power Down disabled (default)
-+ - 2: Power Down enabled
-+ </td></tr>
-+
-+ <tr>
-+ <td>reload_ctl</td>
-+ <td>Specifies whether dynamic reloading of the HFIR register is allowed during
-+ run time. The driver will automatically detect the value for this parameter if
-+ none is specified. In case the HFIR value is reloaded when HFIR.RldCtrl == 1'b0
-+ the core might misbehave.
-+ - 0: Reload Control disabled (default)
-+ - 1: Reload Control enabled
-+ </td></tr>
-+
-+ <tr>
-+ <td>dev_out_nak</td>
-+ <td>Specifies whether Device OUT NAK enhancement enabled or no.
-+ The driver will automatically detect the value for this parameter if
-+ none is specified. This parameter is valid only when OTG_EN_DESC_DMA == 1b1.
-+ - 0: The core does not set NAK after Bulk OUT transfer complete (default)
-+ - 1: The core sets NAK after Bulk OUT transfer complete
-+ </td></tr>
-+
-+ <tr>
-+ <td>cont_on_bna</td>
-+ <td>Specifies whether Enable Continue on BNA enabled or no.
-+ After receiving BNA interrupt the core disables the endpoint,when the
-+ endpoint is re-enabled by the application the
-+ - 0: Core starts processing from the DOEPDMA descriptor (default)
-+ - 1: Core starts processing from the descriptor which received the BNA.
-+ This parameter is valid only when OTG_EN_DESC_DMA == 1b1.
-+ </td></tr>
-+
-+ <tr>
-+ <td>ahb_single</td>
-+ <td>This bit when programmed supports SINGLE transfers for remainder data
-+ in a transfer for DMA mode of operation.
-+ - 0: The remainder data will be sent using INCR burst size (default)
-+ - 1: The remainder data will be sent using SINGLE burst size.
-+ </td></tr>
-+
-+<tr>
-+ <td>adp_enable</td>
-+ <td>Specifies whether ADP feature is enabled.
-+ The driver will automatically detect the value for this parameter if none is
-+ specified.
-+ - 0: ADP feature disabled (default)
-+ - 1: ADP feature enabled
-+ </td></tr>
-+
-+ <tr>
-+ <td>otg_ver</td>
-+ <td>Specifies whether OTG is performing as USB OTG Revision 2.0 or Revision 1.3
-+ USB OTG device.
-+ - 0: OTG 2.0 support disabled (default)
-+ - 1: OTG 2.0 support enabled
-+ </td></tr>
-+
-+*/
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_driver.h
-@@ -0,0 +1,86 @@
-+/* ==========================================================================
-+ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_driver.h $
-+ * $Revision: #19 $
-+ * $Date: 2010/11/15 $
-+ * $Change: 1627671 $
-+ *
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+
-+#ifndef __DWC_OTG_DRIVER_H__
-+#define __DWC_OTG_DRIVER_H__
-+
-+/** @file
-+ * This file contains the interface to the Linux driver.
-+ */
-+#include "dwc_otg_os_dep.h"
-+#include "dwc_otg_core_if.h"
-+
-+/* Type declarations */
-+struct dwc_otg_pcd;
-+struct dwc_otg_hcd;
-+
-+/**
-+ * This structure is a wrapper that encapsulates the driver components used to
-+ * manage a single DWC_otg controller.
-+ */
-+typedef struct dwc_otg_device {
-+ /** Structure containing OS-dependent stuff. KEEP THIS STRUCT AT THE
-+ * VERY BEGINNING OF THE DEVICE STRUCT. OSes such as FreeBSD and NetBSD
-+ * require this. */
-+ struct os_dependent os_dep;
-+
-+ /** Pointer to the core interface structure. */
-+ dwc_otg_core_if_t *core_if;
-+
-+ /** Pointer to the PCD structure. */
-+ struct dwc_otg_pcd *pcd;
-+
-+ /** Pointer to the HCD structure. */
-+ struct dwc_otg_hcd *hcd;
-+
-+ /** Flag to indicate whether the common IRQ handler is installed. */
-+ uint8_t common_irq_installed;
-+
-+} dwc_otg_device_t;
-+
-+/*We must clear S3C24XX_EINTPEND external interrupt register
-+ * because after clearing in this register trigerred IRQ from
-+ * H/W core in kernel interrupt can be occured again before OTG
-+ * handlers clear all IRQ sources of Core registers because of
-+ * timing latencies and Low Level IRQ Type.
-+ */
-+#ifdef CONFIG_MACH_IPMATE
-+#define S3C2410X_CLEAR_EINTPEND() \
-+do { \
-+ __raw_writel(1UL << 11,S3C24XX_EINTPEND); \
-+} while (0)
-+#else
-+#define S3C2410X_CLEAR_EINTPEND() do { } while (0)
-+#endif
-+
-+#endif
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.c
-@@ -0,0 +1,1355 @@
-+/*
-+ * dwc_otg_fiq_fsm.c - The finite state machine FIQ
-+ *
-+ * Copyright (c) 2013 Raspberry Pi Foundation
-+ *
-+ * Author: Jonathan Bell <jonathan at raspberrypi.org>
-+ * All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions are met:
-+ * * Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions and the following disclaimer.
-+ * * Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * * Neither the name of Raspberry Pi nor the
-+ * names of its contributors may be used to endorse or promote products
-+ * derived from this software without specific prior written permission.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND
-+ * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
-+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
-+ * DISCLAIMED. IN NO EVENT SHALL <COPYRIGHT HOLDER> BE LIABLE FOR ANY
-+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
-+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
-+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
-+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ *
-+ * This FIQ implements functionality that performs split transactions on
-+ * the dwc_otg hardware without any outside intervention. A split transaction
-+ * is "queued" by nominating a specific host channel to perform the entirety
-+ * of a split transaction. This FIQ will then perform the microframe-precise
-+ * scheduling required in each phase of the transaction until completion.
-+ *
-+ * The FIQ functionality is glued into the Synopsys driver via the entry point
-+ * in the FSM enqueue function, and at the exit point in handling a HC interrupt
-+ * for a FSM-enabled channel.
-+ *
-+ * NB: Large parts of this implementation have architecture-specific code.
-+ * For porting this functionality to other ARM machines, the minimum is required:
-+ * - An interrupt controller allowing the top-level dwc USB interrupt to be routed
-+ * to the FIQ
-+ * - A method of forcing a software generated interrupt from FIQ mode that then
-+ * triggers an IRQ entry (with the dwc USB handler called by this IRQ number)
-+ * - Guaranteed interrupt routing such that both the FIQ and SGI occur on the same
-+ * processor core - there is no locking between the FIQ and IRQ (aside from
-+ * local_fiq_disable)
-+ *
-+ */
-+
-+#include "dwc_otg_fiq_fsm.h"
-+
-+
-+char buffer[1000*16];
-+int wptr;
-+void notrace _fiq_print(enum fiq_debug_level dbg_lvl, volatile struct fiq_state *state, char *fmt, ...)
-+{
-+ enum fiq_debug_level dbg_lvl_req = FIQDBG_ERR;
-+ va_list args;
-+ char text[17];
-+ hfnum_data_t hfnum = { .d32 = FIQ_READ(state->dwc_regs_base + 0x408) };
-+
-+ if((dbg_lvl & dbg_lvl_req) || dbg_lvl == FIQDBG_ERR)
-+ {
-+ snprintf(text, 9, " %4d:%1u ", hfnum.b.frnum/8, hfnum.b.frnum & 7);
-+ va_start(args, fmt);
-+ vsnprintf(text+8, 9, fmt, args);
-+ va_end(args);
-+
-+ memcpy(buffer + wptr, text, 16);
-+ wptr = (wptr + 16) % sizeof(buffer);
-+ }
-+}
-+
-+/**
-+ * fiq_fsm_spin_lock() - ARMv6+ bare bones spinlock
-+ * Must be called with local interrupts and FIQ disabled.
-+ */
-+#if defined(CONFIG_ARCH_BCM2709) && defined(CONFIG_SMP)
-+inline void fiq_fsm_spin_lock(fiq_lock_t *lock)
-+{
-+ unsigned long tmp;
-+ uint32_t newval;
-+ fiq_lock_t lockval;
-+ smp_mb__before_spinlock();
-+ /* Nested locking, yay. If we are on the same CPU as the fiq, then the disable
-+ * will be sufficient. If we are on a different CPU, then the lock protects us. */
-+ prefetchw(&lock->slock);
-+ asm volatile (
-+ "1: ldrex %0, [%3]\n"
-+ " add %1, %0, %4\n"
-+ " strex %2, %1, [%3]\n"
-+ " teq %2, #0\n"
-+ " bne 1b"
-+ : "=&r" (lockval), "=&r" (newval), "=&r" (tmp)
-+ : "r" (&lock->slock), "I" (1 << 16)
-+ : "cc");
-+
-+ while (lockval.tickets.next != lockval.tickets.owner) {
-+ wfe();
-+ lockval.tickets.owner = ACCESS_ONCE(lock->tickets.owner);
-+ }
-+ smp_mb();
-+}
-+#else
-+inline void fiq_fsm_spin_lock(fiq_lock_t *lock) { }
-+#endif
-+
-+/**
-+ * fiq_fsm_spin_unlock() - ARMv6+ bare bones spinunlock
-+ */
-+#if defined(CONFIG_ARCH_BCM2709) && defined(CONFIG_SMP)
-+inline void fiq_fsm_spin_unlock(fiq_lock_t *lock)
-+{
-+ smp_mb();
-+ lock->tickets.owner++;
-+ dsb_sev();
-+}
-+#else
-+inline void fiq_fsm_spin_unlock(fiq_lock_t *lock) { }
-+#endif
-+
-+/**
-+ * fiq_fsm_restart_channel() - Poke channel enable bit for a split transaction
-+ * @channel: channel to re-enable
-+ */
-+static void fiq_fsm_restart_channel(struct fiq_state *st, int n, int force)
-+{
-+ hcchar_data_t hcchar = { .d32 = FIQ_READ(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCCHAR) };
-+
-+ hcchar.b.chen = 0;
-+ if (st->channel[n].hcchar_copy.b.eptype & 0x1) {
-+ hfnum_data_t hfnum = { .d32 = FIQ_READ(st->dwc_regs_base + HFNUM) };
-+ /* Hardware bug workaround: update the ssplit index */
-+ if (st->channel[n].hcsplt_copy.b.spltena)
-+ st->channel[n].expected_uframe = (hfnum.b.frnum + 1) & 0x3FFF;
-+
-+ hcchar.b.oddfrm = (hfnum.b.frnum & 0x1) ? 0 : 1;
-+ }
-+
-+ FIQ_WRITE(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCCHAR, hcchar.d32);
-+ hcchar.d32 = FIQ_READ(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCCHAR);
-+ hcchar.b.chen = 1;
-+
-+ FIQ_WRITE(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCCHAR, hcchar.d32);
-+ fiq_print(FIQDBG_INT, st, "HCGO %01d %01d", n, force);
-+}
-+
-+/**
-+ * fiq_fsm_setup_csplit() - Prepare a host channel for a CSplit transaction stage
-+ * @st: Pointer to the channel's state
-+ * @n : channel number
-+ *
-+ * Change host channel registers to perform a complete-split transaction. Being mindful of the
-+ * endpoint direction, set control regs up correctly.
-+ */
-+static void notrace fiq_fsm_setup_csplit(struct fiq_state *st, int n)
-+{
-+ hcsplt_data_t hcsplt = { .d32 = FIQ_READ(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCSPLT) };
-+ hctsiz_data_t hctsiz = { .d32 = FIQ_READ(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCTSIZ) };
-+
-+ hcsplt.b.compsplt = 1;
-+ if (st->channel[n].hcchar_copy.b.epdir == 1) {
-+ // If IN, the CSPLIT result contains the data or a hub handshake. hctsiz = maxpacket.
-+ hctsiz.b.xfersize = st->channel[n].hctsiz_copy.b.xfersize;
-+ } else {
-+ // If OUT, the CSPLIT result contains handshake only.
-+ hctsiz.b.xfersize = 0;
-+ }
-+ FIQ_WRITE(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCSPLT, hcsplt.d32);
-+ FIQ_WRITE(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCTSIZ, hctsiz.d32);
-+ mb();
-+}
-+
-+static inline int notrace fiq_get_xfer_len(struct fiq_state *st, int n)
-+{
-+ /* The xfersize register is a bit wonky. For IN transfers, it decrements by the packet size. */
-+ hctsiz_data_t hctsiz = { .d32 = FIQ_READ(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCTSIZ) };
-+
-+ if (st->channel[n].hcchar_copy.b.epdir == 0) {
-+ return st->channel[n].hctsiz_copy.b.xfersize;
-+ } else {
-+ return st->channel[n].hctsiz_copy.b.xfersize - hctsiz.b.xfersize;
-+ }
-+
-+}
-+
-+
-+/**
-+ * fiq_increment_dma_buf() - update DMA address for bounce buffers after a CSPLIT
-+ *
-+ * Of use only for IN periodic transfers.
-+ */
-+static int notrace fiq_increment_dma_buf(struct fiq_state *st, int num_channels, int n)
-+{
-+ hcdma_data_t hcdma;
-+ int i = st->channel[n].dma_info.index;
-+ int len;
-+ struct fiq_dma_blob *blob = (struct fiq_dma_blob *) st->dma_base;
-+
-+ len = fiq_get_xfer_len(st, n);
-+ fiq_print(FIQDBG_INT, st, "LEN: %03d", len);
-+ st->channel[n].dma_info.slot_len[i] = len;
-+ i++;
-+ if (i > 6)
-+ BUG();
-+
-+ hcdma.d32 = (dma_addr_t) &blob->channel[n].index[i].buf[0];
-+ FIQ_WRITE(st->dwc_regs_base + HC_DMA + (HC_OFFSET * n), hcdma.d32);
-+ st->channel[n].dma_info.index = i;
-+ return 0;
-+}
-+
-+/**
-+ * fiq_reload_hctsiz() - for IN transactions, reset HCTSIZ
-+ */
-+static void notrace fiq_fsm_reload_hctsiz(struct fiq_state *st, int n)
-+{
-+ hctsiz_data_t hctsiz = { .d32 = FIQ_READ(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCTSIZ) };
-+ hctsiz.b.xfersize = st->channel[n].hctsiz_copy.b.xfersize;
-+ hctsiz.b.pktcnt = 1;
-+ FIQ_WRITE(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCTSIZ, hctsiz.d32);
-+}
-+
-+/**
-+ * fiq_iso_out_advance() - update DMA address and split position bits
-+ * for isochronous OUT transactions.
-+ *
-+ * Returns 1 if this is the last packet queued, 0 otherwise. Split-ALL and
-+ * Split-BEGIN states are not handled - this is done when the transaction was queued.
-+ *
-+ * This function must only be called from the FIQ_ISO_OUT_ACTIVE state.
-+ */
-+static int notrace fiq_iso_out_advance(struct fiq_state *st, int num_channels, int n)
-+{
-+ hcsplt_data_t hcsplt;
-+ hctsiz_data_t hctsiz;
-+ hcdma_data_t hcdma;
-+ struct fiq_dma_blob *blob = (struct fiq_dma_blob *) st->dma_base;
-+ int last = 0;
-+ int i = st->channel[n].dma_info.index;
-+
-+ fiq_print(FIQDBG_INT, st, "ADV %01d %01d ", n, i);
-+ i++;
-+ if (i == 4)
-+ last = 1;
-+ if (st->channel[n].dma_info.slot_len[i+1] == 255)
-+ last = 1;
-+
-+ /* New DMA address - address of bounce buffer referred to in index */
-+ hcdma.d32 = (uint32_t) &blob->channel[n].index[i].buf[0];
-+ //hcdma.d32 = FIQ_READ(st->dwc_regs_base + HC_DMA + (HC_OFFSET * n));
-+ //hcdma.d32 += st->channel[n].dma_info.slot_len[i];
-+ fiq_print(FIQDBG_INT, st, "LAST: %01d ", last);
-+ fiq_print(FIQDBG_INT, st, "LEN: %03d", st->channel[n].dma_info.slot_len[i]);
-+ hcsplt.d32 = FIQ_READ(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCSPLT);
-+ hctsiz.d32 = FIQ_READ(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCTSIZ);
-+ hcsplt.b.xactpos = (last) ? ISOC_XACTPOS_END : ISOC_XACTPOS_MID;
-+ /* Set up new packet length */
-+ hctsiz.b.pktcnt = 1;
-+ hctsiz.b.xfersize = st->channel[n].dma_info.slot_len[i];
-+ fiq_print(FIQDBG_INT, st, "%08x", hctsiz.d32);
-+
-+ st->channel[n].dma_info.index++;
-+ FIQ_WRITE(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCSPLT, hcsplt.d32);
-+ FIQ_WRITE(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCTSIZ, hctsiz.d32);
-+ FIQ_WRITE(st->dwc_regs_base + HC_DMA + (HC_OFFSET * n), hcdma.d32);
-+ return last;
-+}
-+
-+/**
-+ * fiq_fsm_tt_next_isoc() - queue next pending isochronous out start-split on a TT
-+ *
-+ * Despite the limitations of the DWC core, we can force a microframe pipeline of
-+ * isochronous OUT start-split transactions while waiting for a corresponding other-type
-+ * of endpoint to finish its CSPLITs. TTs have big periodic buffers therefore it
-+ * is very unlikely that filling the start-split FIFO will cause data loss.
-+ * This allows much better interleaving of transactions in an order-independent way-
-+ * there is no requirement to prioritise isochronous, just a state-space search has
-+ * to be performed on each periodic start-split complete interrupt.
-+ */
-+static int notrace fiq_fsm_tt_next_isoc(struct fiq_state *st, int num_channels, int n)
-+{
-+ int hub_addr = st->channel[n].hub_addr;
-+ int port_addr = st->channel[n].port_addr;
-+ int i, poked = 0;
-+ for (i = 0; i < num_channels; i++) {
-+ if (i == n || st->channel[i].fsm == FIQ_PASSTHROUGH)
-+ continue;
-+ if (st->channel[i].hub_addr == hub_addr &&
-+ st->channel[i].port_addr == port_addr) {
-+ switch (st->channel[i].fsm) {
-+ case FIQ_PER_ISO_OUT_PENDING:
-+ if (st->channel[i].nrpackets == 1) {
-+ st->channel[i].fsm = FIQ_PER_ISO_OUT_LAST;
-+ } else {
-+ st->channel[i].fsm = FIQ_PER_ISO_OUT_ACTIVE;
-+ }
-+ fiq_fsm_restart_channel(st, i, 0);
-+ poked = 1;
-+ break;
-+
-+ default:
-+ break;
-+ }
-+ }
-+ if (poked)
-+ break;
-+ }
-+ return poked;
-+}
-+
-+/**
-+ * fiq_fsm_tt_in_use() - search for host channels using this TT
-+ * @n: Channel to use as reference
-+ *
-+ */
-+int notrace noinline fiq_fsm_tt_in_use(struct fiq_state *st, int num_channels, int n)
-+{
-+ int hub_addr = st->channel[n].hub_addr;
-+ int port_addr = st->channel[n].port_addr;
-+ int i, in_use = 0;
-+ for (i = 0; i < num_channels; i++) {
-+ if (i == n || st->channel[i].fsm == FIQ_PASSTHROUGH)
-+ continue;
-+ switch (st->channel[i].fsm) {
-+ /* TT is reserved for channels that are in the middle of a periodic
-+ * split transaction.
-+ */
-+ case FIQ_PER_SSPLIT_STARTED:
-+ case FIQ_PER_CSPLIT_WAIT:
-+ case FIQ_PER_CSPLIT_NYET1:
-+ //case FIQ_PER_CSPLIT_POLL:
-+ case FIQ_PER_ISO_OUT_ACTIVE:
-+ case FIQ_PER_ISO_OUT_LAST:
-+ if (st->channel[i].hub_addr == hub_addr &&
-+ st->channel[i].port_addr == port_addr) {
-+ in_use = 1;
-+ }
-+ break;
-+ default:
-+ break;
-+ }
-+ if (in_use)
-+ break;
-+ }
-+ return in_use;
-+}
-+
-+/**
-+ * fiq_fsm_more_csplits() - determine whether additional CSPLITs need
-+ * to be issued for this IN transaction.
-+ *
-+ * We cannot tell the inbound PID of a data packet due to hardware limitations.
-+ * we need to make an educated guess as to whether we need to queue another CSPLIT
-+ * or not. A no-brainer is when we have received enough data to fill the endpoint
-+ * size, but for endpoints that give variable-length data then we have to resort
-+ * to heuristics.
-+ *
-+ * We also return whether this is the last CSPLIT to be queued, again based on
-+ * heuristics. This is to allow a 1-uframe overlap of periodic split transactions.
-+ * Note: requires at least 1 CSPLIT to have been performed prior to being called.
-+ */
-+
-+/*
-+ * We need some way of guaranteeing if a returned periodic packet of size X
-+ * has a DATA0 PID.
-+ * The heuristic value of 144 bytes assumes that the received data has maximal
-+ * bit-stuffing and the clock frequency of the transmitting device is at the lowest
-+ * permissible limit. If the transfer length results in a final packet size
-+ * 144 < p <= 188, then an erroneous CSPLIT will be issued.
-+ * Also used to ensure that an endpoint will nominally only return a single
-+ * complete-split worth of data.
-+ */
-+#define DATA0_PID_HEURISTIC 144
-+
-+static int notrace noinline fiq_fsm_more_csplits(struct fiq_state *state, int n, int *probably_last)
-+{
-+
-+ int i;
-+ int total_len = 0;
-+ int more_needed = 1;
-+ struct fiq_channel_state *st = &state->channel[n];
-+
-+ for (i = 0; i < st->dma_info.index; i++) {
-+ total_len += st->dma_info.slot_len[i];
-+ }
-+
-+ *probably_last = 0;
-+
-+ if (st->hcchar_copy.b.eptype == 0x3) {
-+ /*
-+ * An interrupt endpoint will take max 2 CSPLITs. if we are receiving data
-+ * then this is definitely the last CSPLIT.
-+ */
-+ *probably_last = 1;
-+ } else {
-+ /* Isoc IN. This is a bit risky if we are the first transaction:
-+ * we may have been held off slightly. */
-+ if (i > 1 && st->dma_info.slot_len[st->dma_info.index-1] <= DATA0_PID_HEURISTIC) {
-+ more_needed = 0;
-+ }
-+ /* If in the next uframe we will receive enough data to fill the endpoint,
-+ * then only issue 1 more csplit.
-+ */
-+ if (st->hctsiz_copy.b.xfersize - total_len <= DATA0_PID_HEURISTIC)
-+ *probably_last = 1;
-+ }
-+
-+ if (total_len >= st->hctsiz_copy.b.xfersize ||
-+ i == 6 || total_len == 0)
-+ /* Note: due to bit stuffing it is possible to have > 6 CSPLITs for
-+ * a single endpoint. Accepting more would completely break our scheduling mechanism though
-+ * - in these extreme cases we will pass through a truncated packet.
-+ */
-+ more_needed = 0;
-+
-+ return more_needed;
-+}
-+
-+/**
-+ * fiq_fsm_too_late() - Test transaction for lateness
-+ *
-+ * If a SSPLIT for a large IN transaction is issued too late in a frame,
-+ * the hub will disable the port to the device and respond with ERR handshakes.
-+ * The hub status endpoint will not reflect this change.
-+ * Returns 1 if we will issue a SSPLIT that will result in a device babble.
-+ */
-+int notrace fiq_fsm_too_late(struct fiq_state *st, int n)
-+{
-+ int uframe;
-+ hfnum_data_t hfnum = { .d32 = FIQ_READ(st->dwc_regs_base + HFNUM) };
-+ uframe = hfnum.b.frnum & 0x7;
-+ if ((uframe < 6) && (st->channel[n].nrpackets + 1 + uframe > 7)) {
-+ return 1;
-+ } else {
-+ return 0;
-+ }
-+}
-+
-+
-+/**
-+ * fiq_fsm_start_next_periodic() - A half-arsed attempt at a microframe pipeline
-+ *
-+ * Search pending transactions in the start-split pending state and queue them.
-+ * Don't queue packets in uframe .5 (comes out in .6) (USB2.0 11.18.4).
-+ * Note: we specifically don't do isochronous OUT transactions first because better
-+ * use of the TT's start-split fifo can be achieved by pipelining an IN before an OUT.
-+ */
-+static void notrace noinline fiq_fsm_start_next_periodic(struct fiq_state *st, int num_channels)
-+{
-+ int n;
-+ hfnum_data_t hfnum = { .d32 = FIQ_READ(st->dwc_regs_base + HFNUM) };
-+ if ((hfnum.b.frnum & 0x7) == 5)
-+ return;
-+ for (n = 0; n < num_channels; n++) {
-+ if (st->channel[n].fsm == FIQ_PER_SSPLIT_QUEUED) {
-+ /* Check to see if any other transactions are using this TT */
-+ if(!fiq_fsm_tt_in_use(st, num_channels, n)) {
-+ if (!fiq_fsm_too_late(st, n)) {
-+ st->channel[n].fsm = FIQ_PER_SSPLIT_STARTED;
-+ fiq_print(FIQDBG_INT, st, "NEXTPER ");
-+ fiq_fsm_restart_channel(st, n, 0);
-+ } else {
-+ st->channel[n].fsm = FIQ_PER_SPLIT_TIMEOUT;
-+ }
-+ break;
-+ }
-+ }
-+ }
-+ for (n = 0; n < num_channels; n++) {
-+ if (st->channel[n].fsm == FIQ_PER_ISO_OUT_PENDING) {
-+ if (!fiq_fsm_tt_in_use(st, num_channels, n)) {
-+ fiq_print(FIQDBG_INT, st, "NEXTISO ");
-+ st->channel[n].fsm = FIQ_PER_ISO_OUT_ACTIVE;
-+ fiq_fsm_restart_channel(st, n, 0);
-+ break;
-+ }
-+ }
-+ }
-+}
-+
-+/**
-+ * fiq_fsm_update_hs_isoc() - update isochronous frame and transfer data
-+ * @state: Pointer to fiq_state
-+ * @n: Channel transaction is active on
-+ * @hcint: Copy of host channel interrupt register
-+ *
-+ * Returns 0 if there are no more transactions for this HC to do, 1
-+ * otherwise.
-+ */
-+static int notrace noinline fiq_fsm_update_hs_isoc(struct fiq_state *state, int n, hcint_data_t hcint)
-+{
-+ struct fiq_channel_state *st = &state->channel[n];
-+ int xfer_len = 0, nrpackets = 0;
-+ hcdma_data_t hcdma;
-+ fiq_print(FIQDBG_INT, state, "HSISO %02d", n);
-+
-+ xfer_len = fiq_get_xfer_len(state, n);
-+ st->hs_isoc_info.iso_desc[st->hs_isoc_info.index].actual_length = xfer_len;
-+
-+ st->hs_isoc_info.iso_desc[st->hs_isoc_info.index].status = hcint.d32;
-+
-+ st->hs_isoc_info.index++;
-+ if (st->hs_isoc_info.index == st->hs_isoc_info.nrframes) {
-+ return 0;
-+ }
-+
-+ /* grab the next DMA address offset from the array */
-+ hcdma.d32 = st->hcdma_copy.d32 + st->hs_isoc_info.iso_desc[st->hs_isoc_info.index].offset;
-+ FIQ_WRITE(state->dwc_regs_base + HC_DMA + (HC_OFFSET * n), hcdma.d32);
-+
-+ /* We need to set multi_count. This is a bit tricky - has to be set per-transaction as
-+ * the core needs to be told to send the correct number. Caution: for IN transfers,
-+ * this is always set to the maximum size of the endpoint. */
-+ xfer_len = st->hs_isoc_info.iso_desc[st->hs_isoc_info.index].length;
-+ /* Integer divide in a FIQ: fun. FIXME: make this not suck */
-+ nrpackets = (xfer_len + st->hcchar_copy.b.mps - 1) / st->hcchar_copy.b.mps;
-+ if (nrpackets == 0)
-+ nrpackets = 1;
-+ st->hcchar_copy.b.multicnt = nrpackets;
-+ st->hctsiz_copy.b.pktcnt = nrpackets;
-+
-+ /* Initial PID also needs to be set */
-+ if (st->hcchar_copy.b.epdir == 0) {
-+ st->hctsiz_copy.b.xfersize = xfer_len;
-+ switch (st->hcchar_copy.b.multicnt) {
-+ case 1:
-+ st->hctsiz_copy.b.pid = DWC_PID_DATA0;
-+ break;
-+ case 2:
-+ case 3:
-+ st->hctsiz_copy.b.pid = DWC_PID_MDATA;
-+ break;
-+ }
-+
-+ } else {
-+ switch (st->hcchar_copy.b.multicnt) {
-+ st->hctsiz_copy.b.xfersize = nrpackets * st->hcchar_copy.b.mps;
-+ case 1:
-+ st->hctsiz_copy.b.pid = DWC_PID_DATA0;
-+ break;
-+ case 2:
-+ st->hctsiz_copy.b.pid = DWC_PID_DATA1;
-+ break;
-+ case 3:
-+ st->hctsiz_copy.b.pid = DWC_PID_DATA2;
-+ break;
-+ }
-+ }
-+ FIQ_WRITE(state->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCTSIZ, st->hctsiz_copy.d32);
-+ FIQ_WRITE(state->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCCHAR, st->hcchar_copy.d32);
-+ /* Channel is enabled on hcint handler exit */
-+ fiq_print(FIQDBG_INT, state, "HSISOOUT");
-+ return 1;
-+}
-+
-+
-+/**
-+ * fiq_fsm_do_sof() - FSM start-of-frame interrupt handler
-+ * @state: Pointer to the state struct passed from banked FIQ mode registers.
-+ * @num_channels: set according to the DWC hardware configuration
-+ *
-+ * The SOF handler in FSM mode has two functions
-+ * 1. Hold off SOF from causing schedule advancement in IRQ context if there's
-+ * nothing to do
-+ * 2. Advance certain FSM states that require either a microframe delay, or a microframe
-+ * of holdoff.
-+ *
-+ * The second part is architecture-specific to mach-bcm2835 -
-+ * a sane interrupt controller would have a mask register for ARM interrupt sources
-+ * to be promoted to the nFIQ line, but it doesn't. Instead a single interrupt
-+ * number (USB) can be enabled. This means that certain parts of the USB specification
-+ * that require "wait a little while, then issue another packet" cannot be fulfilled with
-+ * the timing granularity required to achieve optimal throughout. The workaround is to use
-+ * the SOF "timer" (125uS) to perform this task.
-+ */
-+static int notrace noinline fiq_fsm_do_sof(struct fiq_state *state, int num_channels)
-+{
-+ hfnum_data_t hfnum = { .d32 = FIQ_READ(state->dwc_regs_base + HFNUM) };
-+ int n;
-+ int kick_irq = 0;
-+
-+ if ((hfnum.b.frnum & 0x7) == 1) {
-+ /* We cannot issue csplits for transactions in the last frame past (n+1).1
-+ * Check to see if there are any transactions that are stale.
-+ * Boot them out.
-+ */
-+ for (n = 0; n < num_channels; n++) {
-+ switch (state->channel[n].fsm) {
-+ case FIQ_PER_CSPLIT_WAIT:
-+ case FIQ_PER_CSPLIT_NYET1:
-+ case FIQ_PER_CSPLIT_POLL:
-+ case FIQ_PER_CSPLIT_LAST:
-+ /* Check if we are no longer in the same full-speed frame. */
-+ if (((state->channel[n].expected_uframe & 0x3FFF) & ~0x7) <
-+ (hfnum.b.frnum & ~0x7))
-+ state->channel[n].fsm = FIQ_PER_SPLIT_TIMEOUT;
-+ break;
-+ default:
-+ break;
-+ }
-+ }
-+ }
-+
-+ for (n = 0; n < num_channels; n++) {
-+ switch (state->channel[n].fsm) {
-+
-+ case FIQ_NP_SSPLIT_RETRY:
-+ case FIQ_NP_IN_CSPLIT_RETRY:
-+ case FIQ_NP_OUT_CSPLIT_RETRY:
-+ fiq_fsm_restart_channel(state, n, 0);
-+ break;
-+
-+ case FIQ_HS_ISOC_SLEEPING:
-+ /* Is it time to wake this channel yet? */
-+ if (--state->channel[n].uframe_sleeps == 0) {
-+ state->channel[n].fsm = FIQ_HS_ISOC_TURBO;
-+ fiq_fsm_restart_channel(state, n, 0);
-+ }
-+ break;
-+
-+ case FIQ_PER_SSPLIT_QUEUED:
-+ if ((hfnum.b.frnum & 0x7) == 5)
-+ break;
-+ if(!fiq_fsm_tt_in_use(state, num_channels, n)) {
-+ if (!fiq_fsm_too_late(state, n)) {
-+ fiq_print(FIQDBG_INT, state, "SOF GO %01d", n);
-+ fiq_fsm_restart_channel(state, n, 0);
-+ state->channel[n].fsm = FIQ_PER_SSPLIT_STARTED;
-+ } else {
-+ /* Transaction cannot be started without risking a device babble error */
-+ state->channel[n].fsm = FIQ_PER_SPLIT_TIMEOUT;
-+ state->haintmsk_saved.b2.chint &= ~(1 << n);
-+ FIQ_WRITE(state->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCINTMSK, 0);
-+ kick_irq |= 1;
-+ }
-+ }
-+ break;
-+
-+ case FIQ_PER_ISO_OUT_PENDING:
-+ /* Ordinarily, this should be poked after the SSPLIT
-+ * complete interrupt for a competing transfer on the same
-+ * TT. Doesn't happen for aborted transactions though.
-+ */
-+ if ((hfnum.b.frnum & 0x7) >= 5)
-+ break;
-+ if (!fiq_fsm_tt_in_use(state, num_channels, n)) {
-+ /* Hardware bug. SOF can sometimes occur after the channel halt interrupt
-+ * that caused this.
-+ */
-+ fiq_fsm_restart_channel(state, n, 0);
-+ fiq_print(FIQDBG_INT, state, "SOF ISOC");
-+ if (state->channel[n].nrpackets == 1) {
-+ state->channel[n].fsm = FIQ_PER_ISO_OUT_LAST;
-+ } else {
-+ state->channel[n].fsm = FIQ_PER_ISO_OUT_ACTIVE;
-+ }
-+ }
-+ break;
-+
-+ case FIQ_PER_CSPLIT_WAIT:
-+ /* we are guaranteed to be in this state if and only if the SSPLIT interrupt
-+ * occurred when the bus transaction occurred. The SOF interrupt reversal bug
-+ * will utterly bugger this up though.
-+ */
-+ if (hfnum.b.frnum != state->channel[n].expected_uframe) {
-+ fiq_print(FIQDBG_INT, state, "SOFCS %d ", n);
-+ state->channel[n].fsm = FIQ_PER_CSPLIT_POLL;
-+ fiq_fsm_restart_channel(state, n, 0);
-+ fiq_fsm_start_next_periodic(state, num_channels);
-+
-+ }
-+ break;
-+
-+ case FIQ_PER_SPLIT_TIMEOUT:
-+ case FIQ_DEQUEUE_ISSUED:
-+ /* Ugly: we have to force a HCD interrupt.
-+ * Poke the mask for the channel in question.
-+ * We will take a fake SOF because of this, but
-+ * that's OK.
-+ */
-+ state->haintmsk_saved.b2.chint &= ~(1 << n);
-+ FIQ_WRITE(state->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCINTMSK, 0);
-+ kick_irq |= 1;
-+ break;
-+
-+ default:
-+ break;
-+ }
-+ }
-+
-+ if (state->kick_np_queues ||
-+ dwc_frame_num_le(state->next_sched_frame, hfnum.b.frnum))
-+ kick_irq |= 1;
-+
-+ return !kick_irq;
-+}
-+
-+
-+/**
-+ * fiq_fsm_do_hcintr() - FSM host channel interrupt handler
-+ * @state: Pointer to the FIQ state struct
-+ * @num_channels: Number of channels as per hardware config
-+ * @n: channel for which HAINT(i) was raised
-+ *
-+ * An important property is that only the CHHLT interrupt is unmasked. Unfortunately, AHBerr is as well.
-+ */
-+static int notrace noinline fiq_fsm_do_hcintr(struct fiq_state *state, int num_channels, int n)
-+{
-+ hcint_data_t hcint;
-+ hcintmsk_data_t hcintmsk;
-+ hcint_data_t hcint_probe;
-+ hcchar_data_t hcchar;
-+ int handled = 0;
-+ int restart = 0;
-+ int last_csplit = 0;
-+ int start_next_periodic = 0;
-+ struct fiq_channel_state *st = &state->channel[n];
-+ hfnum_data_t hfnum;
-+
-+ hcint.d32 = FIQ_READ(state->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCINT);
-+ hcintmsk.d32 = FIQ_READ(state->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCINTMSK);
-+ hcint_probe.d32 = hcint.d32 & hcintmsk.d32;
-+
-+ if (st->fsm != FIQ_PASSTHROUGH) {
-+ fiq_print(FIQDBG_INT, state, "HC%01d ST%02d", n, st->fsm);
-+ fiq_print(FIQDBG_INT, state, "%08x", hcint.d32);
-+ }
-+
-+ switch (st->fsm) {
-+
-+ case FIQ_PASSTHROUGH:
-+ case FIQ_DEQUEUE_ISSUED:
-+ /* doesn't belong to us, kick it upstairs */
-+ break;
-+
-+ case FIQ_PASSTHROUGH_ERRORSTATE:
-+ /* We are here to emulate the error recovery mechanism of the dwc HCD.
-+ * Several interrupts are unmasked if a previous transaction failed - it's
-+ * death for the FIQ to attempt to handle them as the channel isn't halted.
-+ * Emulate what the HCD does in this situation: mask and continue.
-+ * The FSM has no other state setup so this has to be handled out-of-band.
-+ */
-+ fiq_print(FIQDBG_ERR, state, "ERRST %02d", n);
-+ if (hcint_probe.b.nak || hcint_probe.b.ack || hcint_probe.b.datatglerr) {
-+ fiq_print(FIQDBG_ERR, state, "RESET %02d", n);
-+ /* In some random cases we can get a NAK interrupt coincident with a Xacterr
-+ * interrupt, after the device has disappeared.
-+ */
-+ if (!hcint.b.xacterr)
-+ st->nr_errors = 0;
-+ hcintmsk.b.nak = 0;
-+ hcintmsk.b.ack = 0;
-+ hcintmsk.b.datatglerr = 0;
-+ FIQ_WRITE(state->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCINTMSK, hcintmsk.d32);
-+ return 1;
-+ }
-+ if (hcint_probe.b.chhltd) {
-+ fiq_print(FIQDBG_ERR, state, "CHHLT %02d", n);
-+ fiq_print(FIQDBG_ERR, state, "%08x", hcint.d32);
-+ return 0;
-+ }
-+ break;
-+
-+ /* Non-periodic state groups */
-+ case FIQ_NP_SSPLIT_STARTED:
-+ case FIQ_NP_SSPLIT_RETRY:
-+ /* Got a HCINT for a NP SSPLIT. Expected ACK / NAK / fail */
-+ if (hcint.b.ack) {
-+ /* SSPLIT complete. For OUT, the data has been sent. For IN, the LS transaction
-+ * will start shortly. SOF needs to kick the transaction to prevent a NYET flood.
-+ */
-+ if(st->hcchar_copy.b.epdir == 1)
-+ st->fsm = FIQ_NP_IN_CSPLIT_RETRY;
-+ else
-+ st->fsm = FIQ_NP_OUT_CSPLIT_RETRY;
-+ st->nr_errors = 0;
-+ handled = 1;
-+ fiq_fsm_setup_csplit(state, n);
-+ } else if (hcint.b.nak) {
-+ // No buffer space in TT. Retry on a uframe boundary.
-+ st->fsm = FIQ_NP_SSPLIT_RETRY;
-+ handled = 1;
-+ } else if (hcint.b.xacterr) {
-+ // The only other one we care about is xacterr. This implies HS bus error - retry.
-+ st->nr_errors++;
-+ st->fsm = FIQ_NP_SSPLIT_RETRY;
-+ if (st->nr_errors >= 3) {
-+ st->fsm = FIQ_NP_SPLIT_HS_ABORTED;
-+ } else {
-+ handled = 1;
-+ restart = 1;
-+ }
-+ } else {
-+ st->fsm = FIQ_NP_SPLIT_LS_ABORTED;
-+ handled = 0;
-+ restart = 0;
-+ }
-+ break;
-+
-+ case FIQ_NP_IN_CSPLIT_RETRY:
-+ /* Received a CSPLIT done interrupt.
-+ * Expected Data/NAK/STALL/NYET for IN.
-+ */
-+ if (hcint.b.xfercomp) {
-+ /* For IN, data is present. */
-+ st->fsm = FIQ_NP_SPLIT_DONE;
-+ } else if (hcint.b.nak) {
-+ /* no endpoint data. Punt it upstairs */
-+ st->fsm = FIQ_NP_SPLIT_DONE;
-+ } else if (hcint.b.nyet) {
-+ /* CSPLIT NYET - retry on a uframe boundary. */
-+ handled = 1;
-+ st->nr_errors = 0;
-+ } else if (hcint.b.datatglerr) {
-+ /* data toggle errors do not set the xfercomp bit. */
-+ st->fsm = FIQ_NP_SPLIT_LS_ABORTED;
-+ } else if (hcint.b.xacterr) {
-+ /* HS error. Retry immediate */
-+ st->fsm = FIQ_NP_IN_CSPLIT_RETRY;
-+ st->nr_errors++;
-+ if (st->nr_errors >= 3) {
-+ st->fsm = FIQ_NP_SPLIT_HS_ABORTED;
-+ } else {
-+ handled = 1;
-+ restart = 1;
-+ }
-+ } else if (hcint.b.stall || hcint.b.bblerr) {
-+ /* A STALL implies either a LS bus error or a genuine STALL. */
-+ st->fsm = FIQ_NP_SPLIT_LS_ABORTED;
-+ } else {
-+ /* Hardware bug. It's possible in some cases to
-+ * get a channel halt with nothing else set when
-+ * the response was a NYET. Treat as local 3-strikes retry.
-+ */
-+ hcint_data_t hcint_test = hcint;
-+ hcint_test.b.chhltd = 0;
-+ if (!hcint_test.d32) {
-+ st->nr_errors++;
-+ if (st->nr_errors >= 3) {
-+ st->fsm = FIQ_NP_SPLIT_HS_ABORTED;
-+ } else {
-+ handled = 1;
-+ }
-+ } else {
-+ /* Bail out if something unexpected happened */
-+ st->fsm = FIQ_NP_SPLIT_HS_ABORTED;
-+ }
-+ }
-+ break;
-+
-+ case FIQ_NP_OUT_CSPLIT_RETRY:
-+ /* Received a CSPLIT done interrupt.
-+ * Expected ACK/NAK/STALL/NYET/XFERCOMP for OUT.*/
-+ if (hcint.b.xfercomp) {
-+ st->fsm = FIQ_NP_SPLIT_DONE;
-+ } else if (hcint.b.nak) {
-+ // The HCD will implement the holdoff on frame boundaries.
-+ st->fsm = FIQ_NP_SPLIT_DONE;
-+ } else if (hcint.b.nyet) {
-+ // Hub still processing.
-+ st->fsm = FIQ_NP_OUT_CSPLIT_RETRY;
-+ handled = 1;
-+ st->nr_errors = 0;
-+ //restart = 1;
-+ } else if (hcint.b.xacterr) {
-+ /* HS error. retry immediate */
-+ st->fsm = FIQ_NP_OUT_CSPLIT_RETRY;
-+ st->nr_errors++;
-+ if (st->nr_errors >= 3) {
-+ st->fsm = FIQ_NP_SPLIT_HS_ABORTED;
-+ } else {
-+ handled = 1;
-+ restart = 1;
-+ }
-+ } else if (hcint.b.stall) {
-+ /* LS bus error or genuine stall */
-+ st->fsm = FIQ_NP_SPLIT_LS_ABORTED;
-+ } else {
-+ /*
-+ * Hardware bug. It's possible in some cases to get a
-+ * channel halt with nothing else set when the response was a NYET.
-+ * Treat as local 3-strikes retry.
-+ */
-+ hcint_data_t hcint_test = hcint;
-+ hcint_test.b.chhltd = 0;
-+ if (!hcint_test.d32) {
-+ st->nr_errors++;
-+ if (st->nr_errors >= 3) {
-+ st->fsm = FIQ_NP_SPLIT_HS_ABORTED;
-+ } else {
-+ handled = 1;
-+ }
-+ } else {
-+ // Something unexpected happened. AHBerror or babble perhaps. Let the IRQ deal with it.
-+ st->fsm = FIQ_NP_SPLIT_HS_ABORTED;
-+ }
-+ }
-+ break;
-+
-+ /* Periodic split states (except isoc out) */
-+ case FIQ_PER_SSPLIT_STARTED:
-+ /* Expect an ACK or failure for SSPLIT */
-+ if (hcint.b.ack) {
-+ /*
-+ * SSPLIT transfer complete interrupt - the generation of this interrupt is fraught with bugs.
-+ * For a packet queued in microframe n-3 to appear in n-2, if the channel is enabled near the EOF1
-+ * point for microframe n-3, the packet will not appear on the bus until microframe n.
-+ * Additionally, the generation of the actual interrupt is dodgy. For a packet appearing on the bus
-+ * in microframe n, sometimes the interrupt is generated immediately. Sometimes, it appears in n+1
-+ * coincident with SOF for n+1.
-+ * SOF is also buggy. It can sometimes be raised AFTER the first bus transaction has taken place.
-+ * These appear to be caused by timing/clock crossing bugs within the core itself.
-+ * State machine workaround.
-+ */
-+ hfnum.d32 = FIQ_READ(state->dwc_regs_base + HFNUM);
-+ hcchar.d32 = FIQ_READ(state->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCCHAR);
-+ fiq_fsm_setup_csplit(state, n);
-+ /* Poke the oddfrm bit. If we are equivalent, we received the interrupt at the correct
-+ * time. If not, then we're in the next SOF.
-+ */
-+ if ((hfnum.b.frnum & 0x1) == hcchar.b.oddfrm) {
-+ fiq_print(FIQDBG_INT, state, "CSWAIT %01d", n);
-+ st->expected_uframe = hfnum.b.frnum;
-+ st->fsm = FIQ_PER_CSPLIT_WAIT;
-+ } else {
-+ fiq_print(FIQDBG_INT, state, "CSPOL %01d", n);
-+ /* For isochronous IN endpoints,
-+ * we need to hold off if we are expecting a lot of data */
-+ if (st->hcchar_copy.b.mps < DATA0_PID_HEURISTIC) {
-+ start_next_periodic = 1;
-+ }
-+ /* Danger will robinson: we are in a broken state. If our first interrupt after
-+ * this is a NYET, it will be delayed by 1 uframe and result in an unrecoverable
-+ * lag. Unmask the NYET interrupt.
-+ */
-+ st->expected_uframe = (hfnum.b.frnum + 1) & 0x3FFF;
-+ st->fsm = FIQ_PER_CSPLIT_BROKEN_NYET1;
-+ restart = 1;
-+ }
-+ handled = 1;
-+ } else if (hcint.b.xacterr) {
-+ /* 3-strikes retry is enabled, we have hit our max nr_errors */
-+ st->fsm = FIQ_PER_SPLIT_HS_ABORTED;
-+ start_next_periodic = 1;
-+ } else {
-+ st->fsm = FIQ_PER_SPLIT_HS_ABORTED;
-+ start_next_periodic = 1;
-+ }
-+ /* We can now queue the next isochronous OUT transaction, if one is pending. */
-+ if(fiq_fsm_tt_next_isoc(state, num_channels, n)) {
-+ fiq_print(FIQDBG_INT, state, "NEXTISO ");
-+ }
-+ break;
-+
-+ case FIQ_PER_CSPLIT_NYET1:
-+ /* First CSPLIT attempt was a NYET. If we get a subsequent NYET,
-+ * we are too late and the TT has dropped its CSPLIT fifo.
-+ */
-+ hfnum.d32 = FIQ_READ(state->dwc_regs_base + HFNUM);
-+ hcchar.d32 = FIQ_READ(state->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCCHAR);
-+ start_next_periodic = 1;
-+ if (hcint.b.nak) {
-+ st->fsm = FIQ_PER_SPLIT_DONE;
-+ } else if (hcint.b.xfercomp) {
-+ fiq_increment_dma_buf(state, num_channels, n);
-+ st->fsm = FIQ_PER_CSPLIT_POLL;
-+ st->nr_errors = 0;
-+ if (fiq_fsm_more_csplits(state, n, &last_csplit)) {
-+ handled = 1;
-+ restart = 1;
-+ if (!last_csplit)
-+ start_next_periodic = 0;
-+ } else {
-+ st->fsm = FIQ_PER_SPLIT_DONE;
-+ }
-+ } else if (hcint.b.nyet) {
-+ /* Doh. Data lost. */
-+ st->fsm = FIQ_PER_SPLIT_NYET_ABORTED;
-+ } else if (hcint.b.xacterr || hcint.b.stall || hcint.b.bblerr) {
-+ st->fsm = FIQ_PER_SPLIT_LS_ABORTED;
-+ } else {
-+ st->fsm = FIQ_PER_SPLIT_HS_ABORTED;
-+ }
-+ break;
-+
-+ case FIQ_PER_CSPLIT_BROKEN_NYET1:
-+ /*
-+ * we got here because our host channel is in the delayed-interrupt
-+ * state and we cannot take a NYET interrupt any later than when it
-+ * occurred. Disable then re-enable the channel if this happens to force
-+ * CSPLITs to occur at the right time.
-+ */
-+ hfnum.d32 = FIQ_READ(state->dwc_regs_base + HFNUM);
-+ hcchar.d32 = FIQ_READ(state->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCCHAR);
-+ fiq_print(FIQDBG_INT, state, "BROK: %01d ", n);
-+ if (hcint.b.nak) {
-+ st->fsm = FIQ_PER_SPLIT_DONE;
-+ start_next_periodic = 1;
-+ } else if (hcint.b.xfercomp) {
-+ fiq_increment_dma_buf(state, num_channels, n);
-+ if (fiq_fsm_more_csplits(state, n, &last_csplit)) {
-+ st->fsm = FIQ_PER_CSPLIT_POLL;
-+ handled = 1;
-+ restart = 1;
-+ start_next_periodic = 1;
-+ /* Reload HCTSIZ for the next transfer */
-+ fiq_fsm_reload_hctsiz(state, n);
-+ if (!last_csplit)
-+ start_next_periodic = 0;
-+ } else {
-+ st->fsm = FIQ_PER_SPLIT_DONE;
-+ }
-+ } else if (hcint.b.nyet) {
-+ st->fsm = FIQ_PER_SPLIT_NYET_ABORTED;
-+ start_next_periodic = 1;
-+ } else if (hcint.b.xacterr || hcint.b.stall || hcint.b.bblerr) {
-+ /* Local 3-strikes retry is handled by the core. This is a ERR response.*/
-+ st->fsm = FIQ_PER_SPLIT_LS_ABORTED;
-+ } else {
-+ st->fsm = FIQ_PER_SPLIT_HS_ABORTED;
-+ }
-+ break;
-+
-+ case FIQ_PER_CSPLIT_POLL:
-+ hfnum.d32 = FIQ_READ(state->dwc_regs_base + HFNUM);
-+ hcchar.d32 = FIQ_READ(state->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCCHAR);
-+ start_next_periodic = 1;
-+ if (hcint.b.nak) {
-+ st->fsm = FIQ_PER_SPLIT_DONE;
-+ } else if (hcint.b.xfercomp) {
-+ fiq_increment_dma_buf(state, num_channels, n);
-+ if (fiq_fsm_more_csplits(state, n, &last_csplit)) {
-+ handled = 1;
-+ restart = 1;
-+ /* Reload HCTSIZ for the next transfer */
-+ fiq_fsm_reload_hctsiz(state, n);
-+ if (!last_csplit)
-+ start_next_periodic = 0;
-+ } else {
-+ st->fsm = FIQ_PER_SPLIT_DONE;
-+ }
-+ } else if (hcint.b.nyet) {
-+ /* Are we a NYET after the first data packet? */
-+ if (st->nrpackets == 0) {
-+ st->fsm = FIQ_PER_CSPLIT_NYET1;
-+ handled = 1;
-+ restart = 1;
-+ } else {
-+ /* We got a NYET when polling CSPLITs. Can happen
-+ * if our heuristic fails, or if someone disables us
-+ * for any significant length of time.
-+ */
-+ if (st->nr_errors >= 3) {
-+ st->fsm = FIQ_PER_SPLIT_NYET_ABORTED;
-+ } else {
-+ st->fsm = FIQ_PER_SPLIT_DONE;
-+ }
-+ }
-+ } else if (hcint.b.xacterr || hcint.b.stall || hcint.b.bblerr) {
-+ /* For xacterr, Local 3-strikes retry is handled by the core. This is a ERR response.*/
-+ st->fsm = FIQ_PER_SPLIT_LS_ABORTED;
-+ } else {
-+ st->fsm = FIQ_PER_SPLIT_HS_ABORTED;
-+ }
-+ break;
-+
-+ case FIQ_HS_ISOC_TURBO:
-+ if (fiq_fsm_update_hs_isoc(state, n, hcint)) {
-+ /* more transactions to come */
-+ handled = 1;
-+ fiq_print(FIQDBG_INT, state, "HSISO M ");
-+ /* For strided transfers, put ourselves to sleep */
-+ if (st->hs_isoc_info.stride > 1) {
-+ st->uframe_sleeps = st->hs_isoc_info.stride - 1;
-+ st->fsm = FIQ_HS_ISOC_SLEEPING;
-+ } else {
-+ restart = 1;
-+ }
-+ } else {
-+ st->fsm = FIQ_HS_ISOC_DONE;
-+ fiq_print(FIQDBG_INT, state, "HSISO F ");
-+ }
-+ break;
-+
-+ case FIQ_HS_ISOC_ABORTED:
-+ /* This abort is called by the driver rewriting the state mid-transaction
-+ * which allows the dequeue mechanism to work more effectively.
-+ */
-+ break;
-+
-+ case FIQ_PER_ISO_OUT_ACTIVE:
-+ if (hcint.b.ack) {
-+ if(fiq_iso_out_advance(state, num_channels, n)) {
-+ /* last OUT transfer */
-+ st->fsm = FIQ_PER_ISO_OUT_LAST;
-+ /*
-+ * Assuming the periodic FIFO in the dwc core
-+ * actually does its job properly, we can queue
-+ * the next ssplit now and in theory, the wire
-+ * transactions will be in-order.
-+ */
-+ // No it doesn't. It appears to process requests in host channel order.
-+ //start_next_periodic = 1;
-+ }
-+ handled = 1;
-+ restart = 1;
-+ } else {
-+ /*
-+ * Isochronous transactions carry on regardless. Log the error
-+ * and continue.
-+ */
-+ //explode += 1;
-+ st->nr_errors++;
-+ if(fiq_iso_out_advance(state, num_channels, n)) {
-+ st->fsm = FIQ_PER_ISO_OUT_LAST;
-+ //start_next_periodic = 1;
-+ }
-+ handled = 1;
-+ restart = 1;
-+ }
-+ break;
-+
-+ case FIQ_PER_ISO_OUT_LAST:
-+ if (hcint.b.ack) {
-+ /* All done here */
-+ st->fsm = FIQ_PER_ISO_OUT_DONE;
-+ } else {
-+ st->fsm = FIQ_PER_ISO_OUT_DONE;
-+ st->nr_errors++;
-+ }
-+ start_next_periodic = 1;
-+ break;
-+
-+ case FIQ_PER_SPLIT_TIMEOUT:
-+ /* SOF kicked us because we overran. */
-+ start_next_periodic = 1;
-+ break;
-+
-+ default:
-+ break;
-+ }
-+
-+ if (handled) {
-+ FIQ_WRITE(state->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCINT, hcint.d32);
-+ } else {
-+ /* Copy the regs into the state so the IRQ knows what to do */
-+ st->hcint_copy.d32 = hcint.d32;
-+ }
-+
-+ if (restart) {
-+ /* Restart always implies handled. */
-+ if (restart == 2) {
-+ /* For complete-split INs, the show must go on.
-+ * Force a channel restart */
-+ fiq_fsm_restart_channel(state, n, 1);
-+ } else {
-+ fiq_fsm_restart_channel(state, n, 0);
-+ }
-+ }
-+ if (start_next_periodic) {
-+ fiq_fsm_start_next_periodic(state, num_channels);
-+ }
-+ if (st->fsm != FIQ_PASSTHROUGH)
-+ fiq_print(FIQDBG_INT, state, "FSMOUT%02d", st->fsm);
-+
-+ return handled;
-+}
-+
-+
-+/**
-+ * dwc_otg_fiq_fsm() - Flying State Machine (monster) FIQ
-+ * @state: pointer to state struct passed from the banked FIQ mode registers.
-+ * @num_channels: set according to the DWC hardware configuration
-+ * @dma: pointer to DMA bounce buffers for split transaction slots
-+ *
-+ * The FSM FIQ performs the low-level tasks that normally would be performed by the microcode
-+ * inside an EHCI or similar host controller regarding split transactions. The DWC core
-+ * interrupts each and every time a split transaction packet is received or sent successfully.
-+ * This results in either an interrupt storm when everything is working "properly", or
-+ * the interrupt latency of the system in general breaks time-sensitive periodic split
-+ * transactions. Pushing the low-level, but relatively easy state machine work into the FIQ
-+ * solves these problems.
-+ *
-+ * Return: void
-+ */
-+void notrace dwc_otg_fiq_fsm(struct fiq_state *state, int num_channels)
-+{
-+ gintsts_data_t gintsts, gintsts_handled;
-+ gintmsk_data_t gintmsk;
-+ //hfnum_data_t hfnum;
-+ haint_data_t haint, haint_handled;
-+ haintmsk_data_t haintmsk;
-+ int kick_irq = 0;
-+
-+ gintsts_handled.d32 = 0;
-+ haint_handled.d32 = 0;
-+
-+ fiq_fsm_spin_lock(&state->lock);
-+ gintsts.d32 = FIQ_READ(state->dwc_regs_base + GINTSTS);
-+ gintmsk.d32 = FIQ_READ(state->dwc_regs_base + GINTMSK);
-+ gintsts.d32 &= gintmsk.d32;
-+
-+ if (gintsts.b.sofintr) {
-+ /* For FSM mode, SOF is required to keep the state machine advance for
-+ * certain stages of the periodic pipeline. It's death to mask this
-+ * interrupt in that case.
-+ */
-+
-+ if (!fiq_fsm_do_sof(state, num_channels)) {
-+ /* Kick IRQ once. Queue advancement means that all pending transactions
-+ * will get serviced when the IRQ finally executes.
-+ */
-+ if (state->gintmsk_saved.b.sofintr == 1)
-+ kick_irq |= 1;
-+ state->gintmsk_saved.b.sofintr = 0;
-+ }
-+ gintsts_handled.b.sofintr = 1;
-+ }
-+
-+ if (gintsts.b.hcintr) {
-+ int i;
-+ haint.d32 = FIQ_READ(state->dwc_regs_base + HAINT);
-+ haintmsk.d32 = FIQ_READ(state->dwc_regs_base + HAINTMSK);
-+ haint.d32 &= haintmsk.d32;
-+ haint_handled.d32 = 0;
-+ for (i=0; i<num_channels; i++) {
-+ if (haint.b2.chint & (1 << i)) {
-+ if(!fiq_fsm_do_hcintr(state, num_channels, i)) {
-+ /* HCINT was not handled in FIQ
-+ * HAINT is level-sensitive, leading to level-sensitive ginststs.b.hcint bit.
-+ * Mask HAINT(i) but keep top-level hcint unmasked.
-+ */
-+ state->haintmsk_saved.b2.chint &= ~(1 << i);
-+ } else {
-+ /* do_hcintr cleaned up after itself, but clear haint */
-+ haint_handled.b2.chint |= (1 << i);
-+ }
-+ }
-+ }
-+
-+ if (haint_handled.b2.chint) {
-+ FIQ_WRITE(state->dwc_regs_base + HAINT, haint_handled.d32);
-+ }
-+
-+ if (haintmsk.d32 != (haintmsk.d32 & state->haintmsk_saved.d32)) {
-+ /*
-+ * This is necessary to avoid multiple retriggers of the MPHI in the case
-+ * where interrupts are held off and HCINTs start to pile up.
-+ * Only wake up the IRQ if a new interrupt came in, was not handled and was
-+ * masked.
-+ */
-+ haintmsk.d32 &= state->haintmsk_saved.d32;
-+ FIQ_WRITE(state->dwc_regs_base + HAINTMSK, haintmsk.d32);
-+ kick_irq |= 1;
-+ }
-+ /* Top-Level interrupt - always handled because it's level-sensitive */
-+ gintsts_handled.b.hcintr = 1;
-+ }
-+
-+
-+ /* Clear the bits in the saved register that were not handled but were triggered. */
-+ state->gintmsk_saved.d32 &= ~(gintsts.d32 & ~gintsts_handled.d32);
-+
-+ /* FIQ didn't handle something - mask has changed - write new mask */
-+ if (gintmsk.d32 != (gintmsk.d32 & state->gintmsk_saved.d32)) {
-+ gintmsk.d32 &= state->gintmsk_saved.d32;
-+ gintmsk.b.sofintr = 1;
-+ FIQ_WRITE(state->dwc_regs_base + GINTMSK, gintmsk.d32);
-+// fiq_print(FIQDBG_INT, state, "KICKGINT");
-+// fiq_print(FIQDBG_INT, state, "%08x", gintmsk.d32);
-+// fiq_print(FIQDBG_INT, state, "%08x", state->gintmsk_saved.d32);
-+ kick_irq |= 1;
-+ }
-+
-+ if (gintsts_handled.d32) {
-+ /* Only applies to edge-sensitive bits in GINTSTS */
-+ FIQ_WRITE(state->dwc_regs_base + GINTSTS, gintsts_handled.d32);
-+ }
-+
-+ /* We got an interrupt, didn't handle it. */
-+ if (kick_irq) {
-+ state->mphi_int_count++;
-+ FIQ_WRITE(state->mphi_regs.outdda, (int) state->dummy_send);
-+ FIQ_WRITE(state->mphi_regs.outddb, (1<<29));
-+
-+ }
-+ state->fiq_done++;
-+ mb();
-+ fiq_fsm_spin_unlock(&state->lock);
-+}
-+
-+
-+/**
-+ * dwc_otg_fiq_nop() - FIQ "lite"
-+ * @state: pointer to state struct passed from the banked FIQ mode registers.
-+ *
-+ * The "nop" handler does not intervene on any interrupts other than SOF.
-+ * It is limited in scope to deciding at each SOF if the IRQ SOF handler (which deals
-+ * with non-periodic/periodic queues) needs to be kicked.
-+ *
-+ * This is done to hold off the SOF interrupt, which occurs at a rate of 8000 per second.
-+ *
-+ * Return: void
-+ */
-+void notrace dwc_otg_fiq_nop(struct fiq_state *state)
-+{
-+ gintsts_data_t gintsts, gintsts_handled;
-+ gintmsk_data_t gintmsk;
-+ hfnum_data_t hfnum;
-+
-+ fiq_fsm_spin_lock(&state->lock);
-+ hfnum.d32 = FIQ_READ(state->dwc_regs_base + HFNUM);
-+ gintsts.d32 = FIQ_READ(state->dwc_regs_base + GINTSTS);
-+ gintmsk.d32 = FIQ_READ(state->dwc_regs_base + GINTMSK);
-+ gintsts.d32 &= gintmsk.d32;
-+ gintsts_handled.d32 = 0;
-+
-+ if (gintsts.b.sofintr) {
-+ if (!state->kick_np_queues &&
-+ dwc_frame_num_gt(state->next_sched_frame, hfnum.b.frnum)) {
-+ /* SOF handled, no work to do, just ACK interrupt */
-+ gintsts_handled.b.sofintr = 1;
-+ } else {
-+ /* Kick IRQ */
-+ state->gintmsk_saved.b.sofintr = 0;
-+ }
-+ }
-+
-+ /* Reset handled interrupts */
-+ if(gintsts_handled.d32) {
-+ FIQ_WRITE(state->dwc_regs_base + GINTSTS, gintsts_handled.d32);
-+ }
-+
-+ /* Clear the bits in the saved register that were not handled but were triggered. */
-+ state->gintmsk_saved.d32 &= ~(gintsts.d32 & ~gintsts_handled.d32);
-+
-+ /* We got an interrupt, didn't handle it and want to mask it */
-+ if (~(state->gintmsk_saved.d32)) {
-+ state->mphi_int_count++;
-+ gintmsk.d32 &= state->gintmsk_saved.d32;
-+ FIQ_WRITE(state->dwc_regs_base + GINTMSK, gintmsk.d32);
-+ /* Force a clear before another dummy send */
-+ FIQ_WRITE(state->mphi_regs.intstat, (1<<29));
-+ FIQ_WRITE(state->mphi_regs.outdda, (int) state->dummy_send);
-+ FIQ_WRITE(state->mphi_regs.outddb, (1<<29));
-+
-+ }
-+ state->fiq_done++;
-+ mb();
-+ fiq_fsm_spin_unlock(&state->lock);
-+}
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.h
-@@ -0,0 +1,370 @@
-+/*
-+ * dwc_otg_fiq_fsm.h - Finite state machine FIQ header definitions
-+ *
-+ * Copyright (c) 2013 Raspberry Pi Foundation
-+ *
-+ * Author: Jonathan Bell <jonathan at raspberrypi.org>
-+ * All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions are met:
-+ * * Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions and the following disclaimer.
-+ * * Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * * Neither the name of Raspberry Pi nor the
-+ * names of its contributors may be used to endorse or promote products
-+ * derived from this software without specific prior written permission.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND
-+ * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
-+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
-+ * DISCLAIMED. IN NO EVENT SHALL <COPYRIGHT HOLDER> BE LIABLE FOR ANY
-+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
-+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
-+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
-+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ *
-+ * This FIQ implements functionality that performs split transactions on
-+ * the dwc_otg hardware without any outside intervention. A split transaction
-+ * is "queued" by nominating a specific host channel to perform the entirety
-+ * of a split transaction. This FIQ will then perform the microframe-precise
-+ * scheduling required in each phase of the transaction until completion.
-+ *
-+ * The FIQ functionality has been surgically implanted into the Synopsys
-+ * vendor-provided driver.
-+ *
-+ */
-+
-+#ifndef DWC_OTG_FIQ_FSM_H_
-+#define DWC_OTG_FIQ_FSM_H_
-+
-+#include "dwc_otg_regs.h"
-+#include "dwc_otg_cil.h"
-+#include "dwc_otg_hcd.h"
-+#include <linux/kernel.h>
-+#include <linux/irqflags.h>
-+#include <linux/string.h>
-+#include <asm/barrier.h>
-+
-+#if 0
-+#define FLAME_ON(x) \
-+do { \
-+ int gpioreg; \
-+ \
-+ gpioreg = readl(__io_address(0x20200000+0x8)); \
-+ gpioreg &= ~(7 << (x-20)*3); \
-+ gpioreg |= 0x1 << (x-20)*3; \
-+ writel(gpioreg, __io_address(0x20200000+0x8)); \
-+ \
-+ writel(1<<x, __io_address(0x20200000+(0x1C))); \
-+} while (0)
-+
-+#define FLAME_OFF(x) \
-+do { \
-+ writel(1<<x, __io_address(0x20200000+(0x28))); \
-+} while (0)
-+#else
-+#define FLAME_ON(x) do { } while (0)
-+#define FLAME_OFF(X) do { } while (0)
-+#endif
-+
-+/* This is a quick-and-dirty arch-specific register read/write. We know that
-+ * writes to a peripheral on BCM2835 will always arrive in-order, also that
-+ * reads and writes are executed in-order therefore the need for memory barriers
-+ * is obviated if we're only talking to USB.
-+ */
-+#define FIQ_WRITE(_addr_,_data_) (*(volatile unsigned int *) (_addr_) = (_data_))
-+#define FIQ_READ(_addr_) (*(volatile unsigned int *) (_addr_))
-+
-+/* FIQ-ified register definitions. Offsets are from dwc_regs_base. */
-+#define GINTSTS 0x014
-+#define GINTMSK 0x018
-+/* Debug register. Poll the top of the received packets FIFO. */
-+#define GRXSTSR 0x01C
-+#define HFNUM 0x408
-+#define HAINT 0x414
-+#define HAINTMSK 0x418
-+#define HPRT0 0x440
-+
-+/* HC_regs start from an offset of 0x500 */
-+#define HC_START 0x500
-+#define HC_OFFSET 0x020
-+
-+#define HC_DMA 0x514
-+
-+#define HCCHAR 0x00
-+#define HCSPLT 0x04
-+#define HCINT 0x08
-+#define HCINTMSK 0x0C
-+#define HCTSIZ 0x10
-+
-+#define ISOC_XACTPOS_ALL 0b11
-+#define ISOC_XACTPOS_BEGIN 0b10
-+#define ISOC_XACTPOS_MID 0b00
-+#define ISOC_XACTPOS_END 0b01
-+
-+#define DWC_PID_DATA2 0b01
-+#define DWC_PID_MDATA 0b11
-+#define DWC_PID_DATA1 0b10
-+#define DWC_PID_DATA0 0b00
-+
-+typedef struct {
-+ volatile void* base;
-+ volatile void* ctrl;
-+ volatile void* outdda;
-+ volatile void* outddb;
-+ volatile void* intstat;
-+} mphi_regs_t;
-+
-+enum fiq_debug_level {
-+ FIQDBG_SCHED = (1 << 0),
-+ FIQDBG_INT = (1 << 1),
-+ FIQDBG_ERR = (1 << 2),
-+ FIQDBG_PORTHUB = (1 << 3),
-+};
-+
-+typedef struct {
-+ union {
-+ uint32_t slock;
-+ struct _tickets {
-+ uint16_t owner;
-+ uint16_t next;
-+ } tickets;
-+ };
-+} fiq_lock_t;
-+
-+struct fiq_state;
-+
-+extern void _fiq_print (enum fiq_debug_level dbg_lvl, volatile struct fiq_state *state, char *fmt, ...);
-+#if 0
-+#define fiq_print _fiq_print
-+#else
-+#define fiq_print(x, y, ...)
-+#endif
-+
-+extern bool fiq_enable, fiq_fsm_enable;
-+extern ushort nak_holdoff;
-+
-+/**
-+ * enum fiq_fsm_state - The FIQ FSM states.
-+ *
-+ * This is the "core" of the FIQ FSM. Broadly, the FSM states follow the
-+ * USB2.0 specification for host responses to various transaction states.
-+ * There are modifications to this host state machine because of a variety of
-+ * quirks and limitations in the dwc_otg hardware.
-+ *
-+ * The fsm state is also used to communicate back to the driver on completion of
-+ * a split transaction. The end states are used in conjunction with the interrupts
-+ * raised by the final transaction.
-+ */
-+enum fiq_fsm_state {
-+ /* FIQ isn't enabled for this host channel */
-+ FIQ_PASSTHROUGH = 0,
-+ /* For the first interrupt received for this channel,
-+ * the FIQ has to ack any interrupts indicating success. */
-+ FIQ_PASSTHROUGH_ERRORSTATE = 31,
-+ /* Nonperiodic state groups */
-+ FIQ_NP_SSPLIT_STARTED = 1,
-+ FIQ_NP_SSPLIT_RETRY = 2,
-+ FIQ_NP_OUT_CSPLIT_RETRY = 3,
-+ FIQ_NP_IN_CSPLIT_RETRY = 4,
-+ FIQ_NP_SPLIT_DONE = 5,
-+ FIQ_NP_SPLIT_LS_ABORTED = 6,
-+ /* This differentiates a HS transaction error from a LS one
-+ * (handling the hub state is different) */
-+ FIQ_NP_SPLIT_HS_ABORTED = 7,
-+
-+ /* Periodic state groups */
-+ /* Periodic transactions are either started directly by the IRQ handler
-+ * or deferred if the TT is already in use.
-+ */
-+ FIQ_PER_SSPLIT_QUEUED = 8,
-+ FIQ_PER_SSPLIT_STARTED = 9,
-+ FIQ_PER_SSPLIT_LAST = 10,
-+
-+
-+ FIQ_PER_ISO_OUT_PENDING = 11,
-+ FIQ_PER_ISO_OUT_ACTIVE = 12,
-+ FIQ_PER_ISO_OUT_LAST = 13,
-+ FIQ_PER_ISO_OUT_DONE = 27,
-+
-+ FIQ_PER_CSPLIT_WAIT = 14,
-+ FIQ_PER_CSPLIT_NYET1 = 15,
-+ FIQ_PER_CSPLIT_BROKEN_NYET1 = 28,
-+ FIQ_PER_CSPLIT_NYET_FAFF = 29,
-+ /* For multiple CSPLITs (large isoc IN, or delayed interrupt) */
-+ FIQ_PER_CSPLIT_POLL = 16,
-+ /* The last CSPLIT for a transaction has been issued, differentiates
-+ * for the state machine to queue the next packet.
-+ */
-+ FIQ_PER_CSPLIT_LAST = 17,
-+
-+ FIQ_PER_SPLIT_DONE = 18,
-+ FIQ_PER_SPLIT_LS_ABORTED = 19,
-+ FIQ_PER_SPLIT_HS_ABORTED = 20,
-+ FIQ_PER_SPLIT_NYET_ABORTED = 21,
-+ /* Frame rollover has occurred without the transaction finishing. */
-+ FIQ_PER_SPLIT_TIMEOUT = 22,
-+
-+ /* FIQ-accelerated HS Isochronous state groups */
-+ FIQ_HS_ISOC_TURBO = 23,
-+ /* For interval > 1, SOF wakes up the isochronous FSM */
-+ FIQ_HS_ISOC_SLEEPING = 24,
-+ FIQ_HS_ISOC_DONE = 25,
-+ FIQ_HS_ISOC_ABORTED = 26,
-+ FIQ_DEQUEUE_ISSUED = 30,
-+ FIQ_TEST = 32,
-+};
-+
-+struct fiq_stack {
-+ int magic1;
-+ uint8_t stack[2048];
-+ int magic2;
-+};
-+
-+
-+/**
-+ * struct fiq_dma_info - DMA bounce buffer utilisation information (per-channel)
-+ * @index: Number of slots reported used for IN transactions / number of slots
-+ * transmitted for an OUT transaction
-+ * @slot_len[6]: Number of actual transfer bytes in each slot (255 if unused)
-+ *
-+ * Split transaction transfers can have variable length depending on other bus
-+ * traffic. The OTG core DMA engine requires 4-byte aligned addresses therefore
-+ * each transaction needs a guaranteed aligned address. A maximum of 6 split transfers
-+ * can happen per-frame.
-+ */
-+struct fiq_dma_info {
-+ u8 index;
-+ u8 slot_len[6];
-+};
-+
-+struct __attribute__((packed)) fiq_split_dma_slot {
-+ u8 buf[188];
-+};
-+
-+struct fiq_dma_channel {
-+ struct __attribute__((packed)) fiq_split_dma_slot index[6];
-+};
-+
-+struct fiq_dma_blob {
-+ struct __attribute__((packed)) fiq_dma_channel channel[0];
-+};
-+
-+/**
-+ * struct fiq_hs_isoc_info - USB2.0 isochronous data
-+ * @iso_frame: Pointer to the array of OTG URB iso_frame_descs.
-+ * @nrframes: Total length of iso_frame_desc array
-+ * @index: Current index (FIQ-maintained)
-+ * @stride: Interval in uframes between HS isoc transactions
-+ */
-+struct fiq_hs_isoc_info {
-+ struct dwc_otg_hcd_iso_packet_desc *iso_desc;
-+ unsigned int nrframes;
-+ unsigned int index;
-+ unsigned int stride;
-+};
-+
-+/**
-+ * struct fiq_channel_state - FIQ state machine storage
-+ * @fsm: Current state of the channel as understood by the FIQ
-+ * @nr_errors: Number of transaction errors on this split-transaction
-+ * @hub_addr: SSPLIT/CSPLIT destination hub
-+ * @port_addr: SSPLIT/CSPLIT destination port - always 1 if single TT hub
-+ * @nrpackets: For isoc OUT, the number of split-OUT packets to transmit. For
-+ * split-IN, number of CSPLIT data packets that were received.
-+ * @hcchar_copy:
-+ * @hcsplt_copy:
-+ * @hcintmsk_copy:
-+ * @hctsiz_copy: Copies of the host channel registers.
-+ * For use as scratch, or for returning state.
-+ *
-+ * The fiq_channel_state is state storage between interrupts for a host channel. The
-+ * FSM state is stored here. Members of this structure must only be set up by the
-+ * driver prior to enabling the FIQ for this host channel, and not touched until the FIQ
-+ * has updated the state to either a COMPLETE state group or ABORT state group.
-+ */
-+
-+struct fiq_channel_state {
-+ enum fiq_fsm_state fsm;
-+ unsigned int nr_errors;
-+ unsigned int hub_addr;
-+ unsigned int port_addr;
-+ /* Hardware bug workaround: sometimes channel halt interrupts are
-+ * delayed until the next SOF. Keep track of when we expected to get interrupted. */
-+ unsigned int expected_uframe;
-+ /* number of uframes remaining (for interval > 1 HS isoc transfers) before next transfer */
-+ unsigned int uframe_sleeps;
-+ /* in/out for communicating number of dma buffers used, or number of ISOC to do */
-+ unsigned int nrpackets;
-+ struct fiq_dma_info dma_info;
-+ struct fiq_hs_isoc_info hs_isoc_info;
-+ /* Copies of HC registers - in/out communication from/to IRQ handler
-+ * and for ease of channel setup. A bit of mungeing is performed - for
-+ * example the hctsiz.b.maxp is _always_ the max packet size of the endpoint.
-+ */
-+ hcchar_data_t hcchar_copy;
-+ hcsplt_data_t hcsplt_copy;
-+ hcint_data_t hcint_copy;
-+ hcintmsk_data_t hcintmsk_copy;
-+ hctsiz_data_t hctsiz_copy;
-+ hcdma_data_t hcdma_copy;
-+};
-+
-+/**
-+ * struct fiq_state - top-level FIQ state machine storage
-+ * @mphi_regs: virtual address of the MPHI peripheral register file
-+ * @dwc_regs_base: virtual address of the base of the DWC core register file
-+ * @dma_base: physical address for the base of the DMA bounce buffers
-+ * @dummy_send: Scratch area for sending a fake message to the MPHI peripheral
-+ * @gintmsk_saved: Top-level mask of interrupts that the FIQ has not handled.
-+ * Used for determining which interrupts fired to set off the IRQ handler.
-+ * @haintmsk_saved: Mask of interrupts from host channels that the FIQ did not handle internally.
-+ * @np_count: Non-periodic transactions in the active queue
-+ * @np_sent: Count of non-periodic transactions that have completed
-+ * @next_sched_frame: For periodic transactions handled by the driver's SOF-driven queuing mechanism,
-+ * this is the next frame on which a SOF interrupt is required. Used to hold off
-+ * passing SOF through to the driver until necessary.
-+ * @channel[n]: Per-channel FIQ state. Allocated during init depending on the number of host
-+ * channels configured into the core logic.
-+ *
-+ * This is passed as the first argument to the dwc_otg_fiq_fsm top-level FIQ handler from the asm stub.
-+ * It contains top-level state information.
-+ */
-+struct fiq_state {
-+ fiq_lock_t lock;
-+ mphi_regs_t mphi_regs;
-+ void *dwc_regs_base;
-+ dma_addr_t dma_base;
-+ struct fiq_dma_blob *fiq_dmab;
-+ void *dummy_send;
-+ gintmsk_data_t gintmsk_saved;
-+ haintmsk_data_t haintmsk_saved;
-+ int mphi_int_count;
-+ unsigned int fiq_done;
-+ unsigned int kick_np_queues;
-+ unsigned int next_sched_frame;
-+#ifdef FIQ_DEBUG
-+ char * buffer;
-+ unsigned int bufsiz;
-+#endif
-+ struct fiq_channel_state channel[0];
-+};
-+
-+extern void fiq_fsm_spin_lock(fiq_lock_t *lock);
-+
-+extern void fiq_fsm_spin_unlock(fiq_lock_t *lock);
-+
-+extern int fiq_fsm_too_late(struct fiq_state *st, int n);
-+
-+extern int fiq_fsm_tt_in_use(struct fiq_state *st, int num_channels, int n);
-+
-+extern void dwc_otg_fiq_fsm(struct fiq_state *state, int num_channels);
-+
-+extern void dwc_otg_fiq_nop(struct fiq_state *state);
-+
-+#endif /* DWC_OTG_FIQ_FSM_H_ */
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_fiq_stub.S
-@@ -0,0 +1,80 @@
-+/*
-+ * dwc_otg_fiq_fsm.S - assembly stub for the FSM FIQ
-+ *
-+ * Copyright (c) 2013 Raspberry Pi Foundation
-+ *
-+ * Author: Jonathan Bell <jonathan at raspberrypi.org>
-+ * All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions are met:
-+ * * Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions and the following disclaimer.
-+ * * Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * * Neither the name of Raspberry Pi nor the
-+ * names of its contributors may be used to endorse or promote products
-+ * derived from this software without specific prior written permission.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND
-+ * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
-+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
-+ * DISCLAIMED. IN NO EVENT SHALL <COPYRIGHT HOLDER> BE LIABLE FOR ANY
-+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
-+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
-+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
-+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+
-+#include <asm/assembler.h>
-+#include <linux/linkage.h>
-+
-+
-+.text
-+
-+.global _dwc_otg_fiq_stub_end;
-+
-+/**
-+ * _dwc_otg_fiq_stub() - entry copied to the FIQ vector page to allow
-+ * a C-style function call with arguments from the FIQ banked registers.
-+ * r0 = &hcd->fiq_state
-+ * r1 = &hcd->num_channels
-+ * r2 = &hcd->dma_buffers
-+ * Tramples: r0, r1, r2, r4, fp, ip
-+ */
-+
-+ENTRY(_dwc_otg_fiq_stub)
-+ /* Stash unbanked regs - SP will have been set up for us */
-+ mov ip, sp;
-+ stmdb sp!, {r0-r12, lr};
-+#ifdef FIQ_DEBUG
-+ // Cycle profiling - read cycle counter at start
-+ mrc p15, 0, r5, c15, c12, 1;
-+#endif
-+ /* r11 = fp, don't trample it */
-+ mov r4, fp;
-+ /* set EABI frame size */
-+ sub fp, ip, #512;
-+
-+ /* for fiq NOP mode - just need state */
-+ mov r0, r8;
-+ /* r9 = num_channels */
-+ mov r1, r9;
-+ /* r10 = struct *dma_bufs */
-+// mov r2, r10;
-+
-+ /* r4 = &fiq_c_function */
-+ blx r4;
-+#ifdef FIQ_DEBUG
-+ mrc p15, 0, r4, c15, c12, 1;
-+ subs r5, r5, r4;
-+ // r5 is now the cycle count time for executing the FIQ. Store it somewhere?
-+#endif
-+ ldmia sp!, {r0-r12, lr};
-+ subs pc, lr, #4;
-+_dwc_otg_fiq_stub_end:
-+END(_dwc_otg_fiq_stub)
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_hcd.c
-@@ -0,0 +1,4257 @@
-+
-+/* ==========================================================================
-+ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_hcd.c $
-+ * $Revision: #104 $
-+ * $Date: 2011/10/24 $
-+ * $Change: 1871159 $
-+ *
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+#ifndef DWC_DEVICE_ONLY
-+
-+/** @file
-+ * This file implements HCD Core. All code in this file is portable and doesn't
-+ * use any OS specific functions.
-+ * Interface provided by HCD Core is defined in <code><hcd_if.h></code>
-+ * header file.
-+ */
-+
-+#include <linux/usb.h>
-+#include <linux/usb/hcd.h>
-+
-+#include "dwc_otg_hcd.h"
-+#include "dwc_otg_regs.h"
-+#include "dwc_otg_fiq_fsm.h"
-+
-+extern bool microframe_schedule;
-+extern uint16_t fiq_fsm_mask, nak_holdoff;
-+
-+//#define DEBUG_HOST_CHANNELS
-+#ifdef DEBUG_HOST_CHANNELS
-+static int last_sel_trans_num_per_scheduled = 0;
-+static int last_sel_trans_num_nonper_scheduled = 0;
-+static int last_sel_trans_num_avail_hc_at_start = 0;
-+static int last_sel_trans_num_avail_hc_at_end = 0;
-+#endif /* DEBUG_HOST_CHANNELS */
-+
-+
-+dwc_otg_hcd_t *dwc_otg_hcd_alloc_hcd(void)
-+{
-+ return DWC_ALLOC(sizeof(dwc_otg_hcd_t));
-+}
-+
-+/**
-+ * Connection timeout function. An OTG host is required to display a
-+ * message if the device does not connect within 10 seconds.
-+ */
-+void dwc_otg_hcd_connect_timeout(void *ptr)
-+{
-+ DWC_DEBUGPL(DBG_HCDV, "%s(%p)\n", __func__, ptr);
-+ DWC_PRINTF("Connect Timeout\n");
-+ __DWC_ERROR("Device Not Connected/Responding\n");
-+}
-+
-+#if defined(DEBUG)
-+static void dump_channel_info(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh)
-+{
-+ if (qh->channel != NULL) {
-+ dwc_hc_t *hc = qh->channel;
-+ dwc_list_link_t *item;
-+ dwc_otg_qh_t *qh_item;
-+ int num_channels = hcd->core_if->core_params->host_channels;
-+ int i;
-+
-+ dwc_otg_hc_regs_t *hc_regs;
-+ hcchar_data_t hcchar;
-+ hcsplt_data_t hcsplt;
-+ hctsiz_data_t hctsiz;
-+ uint32_t hcdma;
-+
-+ hc_regs = hcd->core_if->host_if->hc_regs[hc->hc_num];
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+ hcsplt.d32 = DWC_READ_REG32(&hc_regs->hcsplt);
-+ hctsiz.d32 = DWC_READ_REG32(&hc_regs->hctsiz);
-+ hcdma = DWC_READ_REG32(&hc_regs->hcdma);
-+
-+ DWC_PRINTF(" Assigned to channel %p:\n", hc);
-+ DWC_PRINTF(" hcchar 0x%08x, hcsplt 0x%08x\n", hcchar.d32,
-+ hcsplt.d32);
-+ DWC_PRINTF(" hctsiz 0x%08x, hcdma 0x%08x\n", hctsiz.d32,
-+ hcdma);
-+ DWC_PRINTF(" dev_addr: %d, ep_num: %d, ep_is_in: %d\n",
-+ hc->dev_addr, hc->ep_num, hc->ep_is_in);
-+ DWC_PRINTF(" ep_type: %d\n", hc->ep_type);
-+ DWC_PRINTF(" max_packet: %d\n", hc->max_packet);
-+ DWC_PRINTF(" data_pid_start: %d\n", hc->data_pid_start);
-+ DWC_PRINTF(" xfer_started: %d\n", hc->xfer_started);
-+ DWC_PRINTF(" halt_status: %d\n", hc->halt_status);
-+ DWC_PRINTF(" xfer_buff: %p\n", hc->xfer_buff);
-+ DWC_PRINTF(" xfer_len: %d\n", hc->xfer_len);
-+ DWC_PRINTF(" qh: %p\n", hc->qh);
-+ DWC_PRINTF(" NP inactive sched:\n");
-+ DWC_LIST_FOREACH(item, &hcd->non_periodic_sched_inactive) {
-+ qh_item =
-+ DWC_LIST_ENTRY(item, dwc_otg_qh_t, qh_list_entry);
-+ DWC_PRINTF(" %p\n", qh_item);
-+ }
-+ DWC_PRINTF(" NP active sched:\n");
-+ DWC_LIST_FOREACH(item, &hcd->non_periodic_sched_active) {
-+ qh_item =
-+ DWC_LIST_ENTRY(item, dwc_otg_qh_t, qh_list_entry);
-+ DWC_PRINTF(" %p\n", qh_item);
-+ }
-+ DWC_PRINTF(" Channels: \n");
-+ for (i = 0; i < num_channels; i++) {
-+ dwc_hc_t *hc = hcd->hc_ptr_array[i];
-+ DWC_PRINTF(" %2d: %p\n", i, hc);
-+ }
-+ }
-+}
-+#else
-+#define dump_channel_info(hcd, qh)
-+#endif /* DEBUG */
-+
-+/**
-+ * Work queue function for starting the HCD when A-Cable is connected.
-+ * The hcd_start() must be called in a process context.
-+ */
-+static void hcd_start_func(void *_vp)
-+{
-+ dwc_otg_hcd_t *hcd = (dwc_otg_hcd_t *) _vp;
-+
-+ DWC_DEBUGPL(DBG_HCDV, "%s() %p\n", __func__, hcd);
-+ if (hcd) {
-+ hcd->fops->start(hcd);
-+ }
-+}
-+
-+static void del_xfer_timers(dwc_otg_hcd_t * hcd)
-+{
-+#ifdef DEBUG
-+ int i;
-+ int num_channels = hcd->core_if->core_params->host_channels;
-+ for (i = 0; i < num_channels; i++) {
-+ DWC_TIMER_CANCEL(hcd->core_if->hc_xfer_timer[i]);
-+ }
-+#endif
-+}
-+
-+static void del_timers(dwc_otg_hcd_t * hcd)
-+{
-+ del_xfer_timers(hcd);
-+ DWC_TIMER_CANCEL(hcd->conn_timer);
-+}
-+
-+/**
-+ * Processes all the URBs in a single list of QHs. Completes them with
-+ * -ESHUTDOWN and frees the QTD.
-+ */
-+static void kill_urbs_in_qh_list(dwc_otg_hcd_t * hcd, dwc_list_link_t * qh_list)
-+{
-+ dwc_list_link_t *qh_item, *qh_tmp;
-+ dwc_otg_qh_t *qh;
-+ dwc_otg_qtd_t *qtd, *qtd_tmp;
-+
-+ DWC_LIST_FOREACH_SAFE(qh_item, qh_tmp, qh_list) {
-+ qh = DWC_LIST_ENTRY(qh_item, dwc_otg_qh_t, qh_list_entry);
-+ DWC_CIRCLEQ_FOREACH_SAFE(qtd, qtd_tmp,
-+ &qh->qtd_list, qtd_list_entry) {
-+ qtd = DWC_CIRCLEQ_FIRST(&qh->qtd_list);
-+ if (qtd->urb != NULL) {
-+ hcd->fops->complete(hcd, qtd->urb->priv,
-+ qtd->urb, -DWC_E_SHUTDOWN);
-+ dwc_otg_hcd_qtd_remove_and_free(hcd, qtd, qh);
-+ }
-+
-+ }
-+ if(qh->channel) {
-+ /* Using hcchar.chen == 1 is not a reliable test.
-+ * It is possible that the channel has already halted
-+ * but not yet been through the IRQ handler.
-+ */
-+ dwc_otg_hc_halt(hcd->core_if, qh->channel,
-+ DWC_OTG_HC_XFER_URB_DEQUEUE);
-+ if(microframe_schedule)
-+ hcd->available_host_channels++;
-+ qh->channel = NULL;
-+ }
-+ dwc_otg_hcd_qh_remove(hcd, qh);
-+ }
-+}
-+
-+/**
-+ * Responds with an error status of ESHUTDOWN to all URBs in the non-periodic
-+ * and periodic schedules. The QTD associated with each URB is removed from
-+ * the schedule and freed. This function may be called when a disconnect is
-+ * detected or when the HCD is being stopped.
-+ */
-+static void kill_all_urbs(dwc_otg_hcd_t * hcd)
-+{
-+ kill_urbs_in_qh_list(hcd, &hcd->non_periodic_sched_inactive);
-+ kill_urbs_in_qh_list(hcd, &hcd->non_periodic_sched_active);
-+ kill_urbs_in_qh_list(hcd, &hcd->periodic_sched_inactive);
-+ kill_urbs_in_qh_list(hcd, &hcd->periodic_sched_ready);
-+ kill_urbs_in_qh_list(hcd, &hcd->periodic_sched_assigned);
-+ kill_urbs_in_qh_list(hcd, &hcd->periodic_sched_queued);
-+}
-+
-+/**
-+ * Start the connection timer. An OTG host is required to display a
-+ * message if the device does not connect within 10 seconds. The
-+ * timer is deleted if a port connect interrupt occurs before the
-+ * timer expires.
-+ */
-+static void dwc_otg_hcd_start_connect_timer(dwc_otg_hcd_t * hcd)
-+{
-+ DWC_TIMER_SCHEDULE(hcd->conn_timer, 10000 /* 10 secs */ );
-+}
-+
-+/**
-+ * HCD Callback function for disconnect of the HCD.
-+ *
-+ * @param p void pointer to the <code>struct usb_hcd</code>
-+ */
-+static int32_t dwc_otg_hcd_session_start_cb(void *p)
-+{
-+ dwc_otg_hcd_t *dwc_otg_hcd;
-+ DWC_DEBUGPL(DBG_HCDV, "%s(%p)\n", __func__, p);
-+ dwc_otg_hcd = p;
-+ dwc_otg_hcd_start_connect_timer(dwc_otg_hcd);
-+ return 1;
-+}
-+
-+/**
-+ * HCD Callback function for starting the HCD when A-Cable is
-+ * connected.
-+ *
-+ * @param p void pointer to the <code>struct usb_hcd</code>
-+ */
-+static int32_t dwc_otg_hcd_start_cb(void *p)
-+{
-+ dwc_otg_hcd_t *dwc_otg_hcd = p;
-+ dwc_otg_core_if_t *core_if;
-+ hprt0_data_t hprt0;
-+
-+ core_if = dwc_otg_hcd->core_if;
-+
-+ if (core_if->op_state == B_HOST) {
-+ /*
-+ * Reset the port. During a HNP mode switch the reset
-+ * needs to occur within 1ms and have a duration of at
-+ * least 50ms.
-+ */
-+ hprt0.d32 = dwc_otg_read_hprt0(core_if);
-+ hprt0.b.prtrst = 1;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+ }
-+ DWC_WORKQ_SCHEDULE_DELAYED(core_if->wq_otg,
-+ hcd_start_func, dwc_otg_hcd, 50,
-+ "start hcd");
-+
-+ return 1;
-+}
-+
-+/**
-+ * HCD Callback function for disconnect of the HCD.
-+ *
-+ * @param p void pointer to the <code>struct usb_hcd</code>
-+ */
-+static int32_t dwc_otg_hcd_disconnect_cb(void *p)
-+{
-+ gintsts_data_t intr;
-+ dwc_otg_hcd_t *dwc_otg_hcd = p;
-+
-+ /*
-+ * Set status flags for the hub driver.
-+ */
-+ dwc_otg_hcd->flags.b.port_connect_status_change = 1;
-+ dwc_otg_hcd->flags.b.port_connect_status = 0;
-+ if(fiq_enable)
-+ local_fiq_disable();
-+ /*
-+ * Shutdown any transfers in process by clearing the Tx FIFO Empty
-+ * interrupt mask and status bits and disabling subsequent host
-+ * channel interrupts.
-+ */
-+ intr.d32 = 0;
-+ intr.b.nptxfempty = 1;
-+ intr.b.ptxfempty = 1;
-+ intr.b.hcintr = 1;
-+ DWC_MODIFY_REG32(&dwc_otg_hcd->core_if->core_global_regs->gintmsk,
-+ intr.d32, 0);
-+ DWC_MODIFY_REG32(&dwc_otg_hcd->core_if->core_global_regs->gintsts,
-+ intr.d32, 0);
-+
-+ del_timers(dwc_otg_hcd);
-+
-+ /*
-+ * Turn off the vbus power only if the core has transitioned to device
-+ * mode. If still in host mode, need to keep power on to detect a
-+ * reconnection.
-+ */
-+ if (dwc_otg_is_device_mode(dwc_otg_hcd->core_if)) {
-+ if (dwc_otg_hcd->core_if->op_state != A_SUSPEND) {
-+ hprt0_data_t hprt0 = {.d32 = 0 };
-+ DWC_PRINTF("Disconnect: PortPower off\n");
-+ hprt0.b.prtpwr = 0;
-+ DWC_WRITE_REG32(dwc_otg_hcd->core_if->host_if->hprt0,
-+ hprt0.d32);
-+ }
-+
-+ dwc_otg_disable_host_interrupts(dwc_otg_hcd->core_if);
-+ }
-+
-+ /* Respond with an error status to all URBs in the schedule. */
-+ kill_all_urbs(dwc_otg_hcd);
-+
-+ if (dwc_otg_is_host_mode(dwc_otg_hcd->core_if)) {
-+ /* Clean up any host channels that were in use. */
-+ int num_channels;
-+ int i;
-+ dwc_hc_t *channel;
-+ dwc_otg_hc_regs_t *hc_regs;
-+ hcchar_data_t hcchar;
-+
-+ num_channels = dwc_otg_hcd->core_if->core_params->host_channels;
-+
-+ if (!dwc_otg_hcd->core_if->dma_enable) {
-+ /* Flush out any channel requests in slave mode. */
-+ for (i = 0; i < num_channels; i++) {
-+ channel = dwc_otg_hcd->hc_ptr_array[i];
-+ if (DWC_CIRCLEQ_EMPTY_ENTRY
-+ (channel, hc_list_entry)) {
-+ hc_regs =
-+ dwc_otg_hcd->core_if->
-+ host_if->hc_regs[i];
-+ hcchar.d32 =
-+ DWC_READ_REG32(&hc_regs->hcchar);
-+ if (hcchar.b.chen) {
-+ hcchar.b.chen = 0;
-+ hcchar.b.chdis = 1;
-+ hcchar.b.epdir = 0;
-+ DWC_WRITE_REG32
-+ (&hc_regs->hcchar,
-+ hcchar.d32);
-+ }
-+ }
-+ }
-+ }
-+
-+ for (i = 0; i < num_channels; i++) {
-+ channel = dwc_otg_hcd->hc_ptr_array[i];
-+ if (DWC_CIRCLEQ_EMPTY_ENTRY(channel, hc_list_entry)) {
-+ hc_regs =
-+ dwc_otg_hcd->core_if->host_if->hc_regs[i];
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+ if (hcchar.b.chen) {
-+ /* Halt the channel. */
-+ hcchar.b.chdis = 1;
-+ DWC_WRITE_REG32(&hc_regs->hcchar,
-+ hcchar.d32);
-+ }
-+
-+ dwc_otg_hc_cleanup(dwc_otg_hcd->core_if,
-+ channel);
-+ DWC_CIRCLEQ_INSERT_TAIL
-+ (&dwc_otg_hcd->free_hc_list, channel,
-+ hc_list_entry);
-+ /*
-+ * Added for Descriptor DMA to prevent channel double cleanup
-+ * in release_channel_ddma(). Which called from ep_disable
-+ * when device disconnect.
-+ */
-+ channel->qh = NULL;
-+ }
-+ }
-+ if(fiq_fsm_enable) {
-+ for(i=0; i < 128; i++) {
-+ dwc_otg_hcd->hub_port[i] = 0;
-+ }
-+ }
-+
-+ }
-+
-+ if(fiq_enable)
-+ local_fiq_enable();
-+
-+ if (dwc_otg_hcd->fops->disconnect) {
-+ dwc_otg_hcd->fops->disconnect(dwc_otg_hcd);
-+ }
-+
-+ return 1;
-+}
-+
-+/**
-+ * HCD Callback function for stopping the HCD.
-+ *
-+ * @param p void pointer to the <code>struct usb_hcd</code>
-+ */
-+static int32_t dwc_otg_hcd_stop_cb(void *p)
-+{
-+ dwc_otg_hcd_t *dwc_otg_hcd = p;
-+
-+ DWC_DEBUGPL(DBG_HCDV, "%s(%p)\n", __func__, p);
-+ dwc_otg_hcd_stop(dwc_otg_hcd);
-+ return 1;
-+}
-+
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+/**
-+ * HCD Callback function for sleep of HCD.
-+ *
-+ * @param p void pointer to the <code>struct usb_hcd</code>
-+ */
-+static int dwc_otg_hcd_sleep_cb(void *p)
-+{
-+ dwc_otg_hcd_t *hcd = p;
-+
-+ dwc_otg_hcd_free_hc_from_lpm(hcd);
-+
-+ return 0;
-+}
-+#endif
-+
-+
-+/**
-+ * HCD Callback function for Remote Wakeup.
-+ *
-+ * @param p void pointer to the <code>struct usb_hcd</code>
-+ */
-+static int dwc_otg_hcd_rem_wakeup_cb(void *p)
-+{
-+ dwc_otg_hcd_t *hcd = p;
-+
-+ if (hcd->core_if->lx_state == DWC_OTG_L2) {
-+ hcd->flags.b.port_suspend_change = 1;
-+ }
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+ else {
-+ hcd->flags.b.port_l1_change = 1;
-+ }
-+#endif
-+ return 0;
-+}
-+
-+/**
-+ * Halts the DWC_otg host mode operations in a clean manner. USB transfers are
-+ * stopped.
-+ */
-+void dwc_otg_hcd_stop(dwc_otg_hcd_t * hcd)
-+{
-+ hprt0_data_t hprt0 = {.d32 = 0 };
-+
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD STOP\n");
-+
-+ /*
-+ * The root hub should be disconnected before this function is called.
-+ * The disconnect will clear the QTD lists (via ..._hcd_urb_dequeue)
-+ * and the QH lists (via ..._hcd_endpoint_disable).
-+ */
-+
-+ /* Turn off all host-specific interrupts. */
-+ dwc_otg_disable_host_interrupts(hcd->core_if);
-+
-+ /* Turn off the vbus power */
-+ DWC_PRINTF("PortPower off\n");
-+ hprt0.b.prtpwr = 0;
-+ DWC_WRITE_REG32(hcd->core_if->host_if->hprt0, hprt0.d32);
-+ dwc_mdelay(1);
-+}
-+
-+int dwc_otg_hcd_urb_enqueue(dwc_otg_hcd_t * hcd,
-+ dwc_otg_hcd_urb_t * dwc_otg_urb, void **ep_handle,
-+ int atomic_alloc)
-+{
-+ int retval = 0;
-+ uint8_t needs_scheduling = 0;
-+ dwc_otg_transaction_type_e tr_type;
-+ dwc_otg_qtd_t *qtd;
-+ gintmsk_data_t intr_mask = {.d32 = 0 };
-+ hprt0_data_t hprt0 = { .d32 = 0 };
-+
-+#ifdef DEBUG /* integrity checks (Broadcom) */
-+ if (NULL == hcd->core_if) {
-+ DWC_ERROR("**** DWC OTG HCD URB Enqueue - HCD has NULL core_if\n");
-+ /* No longer connected. */
-+ return -DWC_E_INVALID;
-+ }
-+#endif
-+ if (!hcd->flags.b.port_connect_status) {
-+ /* No longer connected. */
-+ DWC_ERROR("Not connected\n");
-+ return -DWC_E_NO_DEVICE;
-+ }
-+
-+ /* Some core configurations cannot support LS traffic on a FS root port */
-+ if ((hcd->fops->speed(hcd, dwc_otg_urb->priv) == USB_SPEED_LOW) &&
-+ (hcd->core_if->hwcfg2.b.fs_phy_type == 1) &&
-+ (hcd->core_if->hwcfg2.b.hs_phy_type == 1)) {
-+ hprt0.d32 = DWC_READ_REG32(hcd->core_if->host_if->hprt0);
-+ if (hprt0.b.prtspd == DWC_HPRT0_PRTSPD_FULL_SPEED) {
-+ return -DWC_E_NO_DEVICE;
-+ }
-+ }
-+
-+ qtd = dwc_otg_hcd_qtd_create(dwc_otg_urb, atomic_alloc);
-+ if (qtd == NULL) {
-+ DWC_ERROR("DWC OTG HCD URB Enqueue failed creating QTD\n");
-+ return -DWC_E_NO_MEMORY;
-+ }
-+#ifdef DEBUG /* integrity checks (Broadcom) */
-+ if (qtd->urb == NULL) {
-+ DWC_ERROR("**** DWC OTG HCD URB Enqueue created QTD with no URBs\n");
-+ return -DWC_E_NO_MEMORY;
-+ }
-+ if (qtd->urb->priv == NULL) {
-+ DWC_ERROR("**** DWC OTG HCD URB Enqueue created QTD URB with no URB handle\n");
-+ return -DWC_E_NO_MEMORY;
-+ }
-+#endif
-+ intr_mask.d32 = DWC_READ_REG32(&hcd->core_if->core_global_regs->gintmsk);
-+ if(!intr_mask.b.sofintr || fiq_enable) needs_scheduling = 1;
-+ if((((dwc_otg_qh_t *)ep_handle)->ep_type == UE_BULK) && !(qtd->urb->flags & URB_GIVEBACK_ASAP))
-+ /* Do not schedule SG transactions until qtd has URB_GIVEBACK_ASAP set */
-+ needs_scheduling = 0;
-+
-+ retval = dwc_otg_hcd_qtd_add(qtd, hcd, (dwc_otg_qh_t **) ep_handle, atomic_alloc);
-+ // creates a new queue in ep_handle if it doesn't exist already
-+ if (retval < 0) {
-+ DWC_ERROR("DWC OTG HCD URB Enqueue failed adding QTD. "
-+ "Error status %d\n", retval);
-+ dwc_otg_hcd_qtd_free(qtd);
-+ return retval;
-+ }
-+
-+ if(needs_scheduling) {
-+ tr_type = dwc_otg_hcd_select_transactions(hcd);
-+ if (tr_type != DWC_OTG_TRANSACTION_NONE) {
-+ dwc_otg_hcd_queue_transactions(hcd, tr_type);
-+ }
-+ }
-+ return retval;
-+}
-+
-+int dwc_otg_hcd_urb_dequeue(dwc_otg_hcd_t * hcd,
-+ dwc_otg_hcd_urb_t * dwc_otg_urb)
-+{
-+ dwc_otg_qh_t *qh;
-+ dwc_otg_qtd_t *urb_qtd;
-+ BUG_ON(!hcd);
-+ BUG_ON(!dwc_otg_urb);
-+
-+#ifdef DEBUG /* integrity checks (Broadcom) */
-+
-+ if (hcd == NULL) {
-+ DWC_ERROR("**** DWC OTG HCD URB Dequeue has NULL HCD\n");
-+ return -DWC_E_INVALID;
-+ }
-+ if (dwc_otg_urb == NULL) {
-+ DWC_ERROR("**** DWC OTG HCD URB Dequeue has NULL URB\n");
-+ return -DWC_E_INVALID;
-+ }
-+ if (dwc_otg_urb->qtd == NULL) {
-+ DWC_ERROR("**** DWC OTG HCD URB Dequeue with NULL QTD\n");
-+ return -DWC_E_INVALID;
-+ }
-+ urb_qtd = dwc_otg_urb->qtd;
-+ BUG_ON(!urb_qtd);
-+ if (urb_qtd->qh == NULL) {
-+ DWC_ERROR("**** DWC OTG HCD URB Dequeue with QTD with NULL Q handler\n");
-+ return -DWC_E_INVALID;
-+ }
-+#else
-+ urb_qtd = dwc_otg_urb->qtd;
-+ BUG_ON(!urb_qtd);
-+#endif
-+ qh = urb_qtd->qh;
-+ BUG_ON(!qh);
-+ if (CHK_DEBUG_LEVEL(DBG_HCDV | DBG_HCD_URB)) {
-+ if (urb_qtd->in_process) {
-+ dump_channel_info(hcd, qh);
-+ }
-+ }
-+#ifdef DEBUG /* integrity checks (Broadcom) */
-+ if (hcd->core_if == NULL) {
-+ DWC_ERROR("**** DWC OTG HCD URB Dequeue HCD has NULL core_if\n");
-+ return -DWC_E_INVALID;
-+ }
-+#endif
-+ if (urb_qtd->in_process && qh->channel) {
-+ /* The QTD is in process (it has been assigned to a channel). */
-+ if (hcd->flags.b.port_connect_status) {
-+ int n = qh->channel->hc_num;
-+ /*
-+ * If still connected (i.e. in host mode), halt the
-+ * channel so it can be used for other transfers. If
-+ * no longer connected, the host registers can't be
-+ * written to halt the channel since the core is in
-+ * device mode.
-+ */
-+ /* In FIQ FSM mode, we need to shut down carefully.
-+ * The FIQ may attempt to restart a disabled channel */
-+ if (fiq_fsm_enable && (hcd->fiq_state->channel[n].fsm != FIQ_PASSTHROUGH)) {
-+ qh->channel->halt_status = DWC_OTG_HC_XFER_URB_DEQUEUE;
-+ qh->channel->halt_pending = 1;
-+ hcd->fiq_state->channel[n].fsm = FIQ_DEQUEUE_ISSUED;
-+ } else {
-+ dwc_otg_hc_halt(hcd->core_if, qh->channel,
-+ DWC_OTG_HC_XFER_URB_DEQUEUE);
-+ }
-+ }
-+ }
-+
-+ /*
-+ * Free the QTD and clean up the associated QH. Leave the QH in the
-+ * schedule if it has any remaining QTDs.
-+ */
-+
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD URB Dequeue - "
-+ "delete %sQueue handler\n",
-+ hcd->core_if->dma_desc_enable?"DMA ":"");
-+ if (!hcd->core_if->dma_desc_enable) {
-+ uint8_t b = urb_qtd->in_process;
-+ dwc_otg_hcd_qtd_remove_and_free(hcd, urb_qtd, qh);
-+ if (b) {
-+ dwc_otg_hcd_qh_deactivate(hcd, qh, 0);
-+ qh->channel = NULL;
-+ } else if (DWC_CIRCLEQ_EMPTY(&qh->qtd_list)) {
-+ dwc_otg_hcd_qh_remove(hcd, qh);
-+ }
-+ } else {
-+ dwc_otg_hcd_qtd_remove_and_free(hcd, urb_qtd, qh);
-+ }
-+ return 0;
-+}
-+
-+int dwc_otg_hcd_endpoint_disable(dwc_otg_hcd_t * hcd, void *ep_handle,
-+ int retry)
-+{
-+ dwc_otg_qh_t *qh = (dwc_otg_qh_t *) ep_handle;
-+ int retval = 0;
-+ dwc_irqflags_t flags;
-+
-+ if (retry < 0) {
-+ retval = -DWC_E_INVALID;
-+ goto done;
-+ }
-+
-+ if (!qh) {
-+ retval = -DWC_E_INVALID;
-+ goto done;
-+ }
-+
-+ DWC_SPINLOCK_IRQSAVE(hcd->lock, &flags);
-+
-+ while (!DWC_CIRCLEQ_EMPTY(&qh->qtd_list) && retry) {
-+ DWC_SPINUNLOCK_IRQRESTORE(hcd->lock, flags);
-+ retry--;
-+ dwc_msleep(5);
-+ DWC_SPINLOCK_IRQSAVE(hcd->lock, &flags);
-+ }
-+
-+ dwc_otg_hcd_qh_remove(hcd, qh);
-+
-+ DWC_SPINUNLOCK_IRQRESTORE(hcd->lock, flags);
-+ /*
-+ * Split dwc_otg_hcd_qh_remove_and_free() into qh_remove
-+ * and qh_free to prevent stack dump on DWC_DMA_FREE() with
-+ * irq_disabled (spinlock_irqsave) in dwc_otg_hcd_desc_list_free()
-+ * and dwc_otg_hcd_frame_list_alloc().
-+ */
-+ dwc_otg_hcd_qh_free(hcd, qh);
-+
-+done:
-+ return retval;
-+}
-+
-+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,30)
-+int dwc_otg_hcd_endpoint_reset(dwc_otg_hcd_t * hcd, void *ep_handle)
-+{
-+ int retval = 0;
-+ dwc_otg_qh_t *qh = (dwc_otg_qh_t *) ep_handle;
-+ if (!qh)
-+ return -DWC_E_INVALID;
-+
-+ qh->data_toggle = DWC_OTG_HC_PID_DATA0;
-+ return retval;
-+}
-+#endif
-+
-+/**
-+ * HCD Callback structure for handling mode switching.
-+ */
-+static dwc_otg_cil_callbacks_t hcd_cil_callbacks = {
-+ .start = dwc_otg_hcd_start_cb,
-+ .stop = dwc_otg_hcd_stop_cb,
-+ .disconnect = dwc_otg_hcd_disconnect_cb,
-+ .session_start = dwc_otg_hcd_session_start_cb,
-+ .resume_wakeup = dwc_otg_hcd_rem_wakeup_cb,
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+ .sleep = dwc_otg_hcd_sleep_cb,
-+#endif
-+ .p = 0,
-+};
-+
-+/**
-+ * Reset tasklet function
-+ */
-+static void reset_tasklet_func(void *data)
-+{
-+ dwc_otg_hcd_t *dwc_otg_hcd = (dwc_otg_hcd_t *) data;
-+ dwc_otg_core_if_t *core_if = dwc_otg_hcd->core_if;
-+ hprt0_data_t hprt0;
-+
-+ DWC_DEBUGPL(DBG_HCDV, "USB RESET tasklet called\n");
-+
-+ hprt0.d32 = dwc_otg_read_hprt0(core_if);
-+ hprt0.b.prtrst = 1;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+ dwc_mdelay(60);
-+
-+ hprt0.b.prtrst = 0;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+ dwc_otg_hcd->flags.b.port_reset_change = 1;
-+}
-+
-+static void completion_tasklet_func(void *ptr)
-+{
-+ dwc_otg_hcd_t *hcd = (dwc_otg_hcd_t *) ptr;
-+ struct urb *urb;
-+ urb_tq_entry_t *item;
-+ dwc_irqflags_t flags;
-+
-+ /* This could just be spin_lock_irq */
-+ DWC_SPINLOCK_IRQSAVE(hcd->lock, &flags);
-+ while (!DWC_TAILQ_EMPTY(&hcd->completed_urb_list)) {
-+ item = DWC_TAILQ_FIRST(&hcd->completed_urb_list);
-+ urb = item->urb;
-+ DWC_TAILQ_REMOVE(&hcd->completed_urb_list, item,
-+ urb_tq_entries);
-+ DWC_SPINUNLOCK_IRQRESTORE(hcd->lock, flags);
-+ DWC_FREE(item);
-+
-+ usb_hcd_giveback_urb(hcd->priv, urb, urb->status);
-+
-+
-+ DWC_SPINLOCK_IRQSAVE(hcd->lock, &flags);
-+ }
-+ DWC_SPINUNLOCK_IRQRESTORE(hcd->lock, flags);
-+ return;
-+}
-+
-+static void qh_list_free(dwc_otg_hcd_t * hcd, dwc_list_link_t * qh_list)
-+{
-+ dwc_list_link_t *item;
-+ dwc_otg_qh_t *qh;
-+ dwc_irqflags_t flags;
-+
-+ if (!qh_list->next) {
-+ /* The list hasn't been initialized yet. */
-+ return;
-+ }
-+ /*
-+ * Hold spinlock here. Not needed in that case if bellow
-+ * function is being called from ISR
-+ */
-+ DWC_SPINLOCK_IRQSAVE(hcd->lock, &flags);
-+ /* Ensure there are no QTDs or URBs left. */
-+ kill_urbs_in_qh_list(hcd, qh_list);
-+ DWC_SPINUNLOCK_IRQRESTORE(hcd->lock, flags);
-+
-+ DWC_LIST_FOREACH(item, qh_list) {
-+ qh = DWC_LIST_ENTRY(item, dwc_otg_qh_t, qh_list_entry);
-+ dwc_otg_hcd_qh_remove_and_free(hcd, qh);
-+ }
-+}
-+
-+/**
-+ * Exit from Hibernation if Host did not detect SRP from connected SRP capable
-+ * Device during SRP time by host power up.
-+ */
-+void dwc_otg_hcd_power_up(void *ptr)
-+{
-+ gpwrdn_data_t gpwrdn = {.d32 = 0 };
-+ dwc_otg_core_if_t *core_if = (dwc_otg_core_if_t *) ptr;
-+
-+ DWC_PRINTF("%s called\n", __FUNCTION__);
-+
-+ if (!core_if->hibernation_suspend) {
-+ DWC_PRINTF("Already exited from Hibernation\n");
-+ return;
-+ }
-+
-+ /* Switch on the voltage to the core */
-+ gpwrdn.b.pwrdnswtch = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ dwc_udelay(10);
-+
-+ /* Reset the core */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnrstn = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ dwc_udelay(10);
-+
-+ /* Disable power clamps */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnclmp = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+
-+ /* Remove reset the core signal */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnrstn = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32);
-+ dwc_udelay(10);
-+
-+ /* Disable PMU interrupt */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuintsel = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+
-+ core_if->hibernation_suspend = 0;
-+
-+ /* Disable PMU */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuactv = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+ dwc_udelay(10);
-+
-+ /* Enable VBUS */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.dis_vbus = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0);
-+
-+ core_if->op_state = A_HOST;
-+ dwc_otg_core_init(core_if);
-+ dwc_otg_enable_global_interrupts(core_if);
-+ cil_hcd_start(core_if);
-+}
-+
-+void dwc_otg_cleanup_fiq_channel(dwc_otg_hcd_t *hcd, uint32_t num)
-+{
-+ struct fiq_channel_state *st = &hcd->fiq_state->channel[num];
-+ struct fiq_dma_blob *blob = hcd->fiq_dmab;
-+ int i;
-+
-+ st->fsm = FIQ_PASSTHROUGH;
-+ st->hcchar_copy.d32 = 0;
-+ st->hcsplt_copy.d32 = 0;
-+ st->hcint_copy.d32 = 0;
-+ st->hcintmsk_copy.d32 = 0;
-+ st->hctsiz_copy.d32 = 0;
-+ st->hcdma_copy.d32 = 0;
-+ st->nr_errors = 0;
-+ st->hub_addr = 0;
-+ st->port_addr = 0;
-+ st->expected_uframe = 0;
-+ st->nrpackets = 0;
-+ st->dma_info.index = 0;
-+ for (i = 0; i < 6; i++)
-+ st->dma_info.slot_len[i] = 255;
-+ st->hs_isoc_info.index = 0;
-+ st->hs_isoc_info.iso_desc = NULL;
-+ st->hs_isoc_info.nrframes = 0;
-+
-+ DWC_MEMSET(&blob->channel[num].index[0], 0x6b, 1128);
-+}
-+
-+/**
-+ * Frees secondary storage associated with the dwc_otg_hcd structure contained
-+ * in the struct usb_hcd field.
-+ */
-+static void dwc_otg_hcd_free(dwc_otg_hcd_t * dwc_otg_hcd)
-+{
-+ int i;
-+
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD FREE\n");
-+
-+ del_timers(dwc_otg_hcd);
-+
-+ /* Free memory for QH/QTD lists */
-+ qh_list_free(dwc_otg_hcd, &dwc_otg_hcd->non_periodic_sched_inactive);
-+ qh_list_free(dwc_otg_hcd, &dwc_otg_hcd->non_periodic_sched_active);
-+ qh_list_free(dwc_otg_hcd, &dwc_otg_hcd->periodic_sched_inactive);
-+ qh_list_free(dwc_otg_hcd, &dwc_otg_hcd->periodic_sched_ready);
-+ qh_list_free(dwc_otg_hcd, &dwc_otg_hcd->periodic_sched_assigned);
-+ qh_list_free(dwc_otg_hcd, &dwc_otg_hcd->periodic_sched_queued);
-+
-+ /* Free memory for the host channels. */
-+ for (i = 0; i < MAX_EPS_CHANNELS; i++) {
-+ dwc_hc_t *hc = dwc_otg_hcd->hc_ptr_array[i];
-+
-+#ifdef DEBUG
-+ if (dwc_otg_hcd->core_if->hc_xfer_timer[i]) {
-+ DWC_TIMER_FREE(dwc_otg_hcd->core_if->hc_xfer_timer[i]);
-+ }
-+#endif
-+ if (hc != NULL) {
-+ DWC_DEBUGPL(DBG_HCDV, "HCD Free channel #%i, hc=%p\n",
-+ i, hc);
-+ DWC_FREE(hc);
-+ }
-+ }
-+
-+ if (dwc_otg_hcd->core_if->dma_enable) {
-+ if (dwc_otg_hcd->status_buf_dma) {
-+ DWC_DMA_FREE(DWC_OTG_HCD_STATUS_BUF_SIZE,
-+ dwc_otg_hcd->status_buf,
-+ dwc_otg_hcd->status_buf_dma);
-+ }
-+ } else if (dwc_otg_hcd->status_buf != NULL) {
-+ DWC_FREE(dwc_otg_hcd->status_buf);
-+ }
-+ DWC_SPINLOCK_FREE(dwc_otg_hcd->channel_lock);
-+ DWC_SPINLOCK_FREE(dwc_otg_hcd->lock);
-+ /* Set core_if's lock pointer to NULL */
-+ dwc_otg_hcd->core_if->lock = NULL;
-+
-+ DWC_TIMER_FREE(dwc_otg_hcd->conn_timer);
-+ DWC_TASK_FREE(dwc_otg_hcd->reset_tasklet);
-+ DWC_TASK_FREE(dwc_otg_hcd->completion_tasklet);
-+ DWC_FREE(dwc_otg_hcd->fiq_state);
-+
-+#ifdef DWC_DEV_SRPCAP
-+ if (dwc_otg_hcd->core_if->power_down == 2 &&
-+ dwc_otg_hcd->core_if->pwron_timer) {
-+ DWC_TIMER_FREE(dwc_otg_hcd->core_if->pwron_timer);
-+ }
-+#endif
-+ DWC_FREE(dwc_otg_hcd);
-+}
-+
-+int init_hcd_usecs(dwc_otg_hcd_t *_hcd);
-+
-+int dwc_otg_hcd_init(dwc_otg_hcd_t * hcd, dwc_otg_core_if_t * core_if)
-+{
-+ int retval = 0;
-+ int num_channels;
-+ int i;
-+ dwc_hc_t *channel;
-+
-+#if (defined(DWC_LINUX) && defined(CONFIG_DEBUG_SPINLOCK))
-+ DWC_SPINLOCK_ALLOC_LINUX_DEBUG(hcd->lock);
-+ DWC_SPINLOCK_ALLOC_LINUX_DEBUG(hcd->channel_lock);
-+#else
-+ hcd->lock = DWC_SPINLOCK_ALLOC();
-+ hcd->channel_lock = DWC_SPINLOCK_ALLOC();
-+#endif
-+ DWC_DEBUGPL(DBG_HCDV, "init of HCD %p given core_if %p\n",
-+ hcd, core_if);
-+ if (!hcd->lock) {
-+ DWC_ERROR("Could not allocate lock for pcd");
-+ DWC_FREE(hcd);
-+ retval = -DWC_E_NO_MEMORY;
-+ goto out;
-+ }
-+ hcd->core_if = core_if;
-+
-+ /* Register the HCD CIL Callbacks */
-+ dwc_otg_cil_register_hcd_callbacks(hcd->core_if,
-+ &hcd_cil_callbacks, hcd);
-+
-+ /* Initialize the non-periodic schedule. */
-+ DWC_LIST_INIT(&hcd->non_periodic_sched_inactive);
-+ DWC_LIST_INIT(&hcd->non_periodic_sched_active);
-+
-+ /* Initialize the periodic schedule. */
-+ DWC_LIST_INIT(&hcd->periodic_sched_inactive);
-+ DWC_LIST_INIT(&hcd->periodic_sched_ready);
-+ DWC_LIST_INIT(&hcd->periodic_sched_assigned);
-+ DWC_LIST_INIT(&hcd->periodic_sched_queued);
-+ DWC_TAILQ_INIT(&hcd->completed_urb_list);
-+ /*
-+ * Create a host channel descriptor for each host channel implemented
-+ * in the controller. Initialize the channel descriptor array.
-+ */
-+ DWC_CIRCLEQ_INIT(&hcd->free_hc_list);
-+ num_channels = hcd->core_if->core_params->host_channels;
-+ DWC_MEMSET(hcd->hc_ptr_array, 0, sizeof(hcd->hc_ptr_array));
-+ for (i = 0; i < num_channels; i++) {
-+ channel = DWC_ALLOC(sizeof(dwc_hc_t));
-+ if (channel == NULL) {
-+ retval = -DWC_E_NO_MEMORY;
-+ DWC_ERROR("%s: host channel allocation failed\n",
-+ __func__);
-+ dwc_otg_hcd_free(hcd);
-+ goto out;
-+ }
-+ channel->hc_num = i;
-+ hcd->hc_ptr_array[i] = channel;
-+#ifdef DEBUG
-+ hcd->core_if->hc_xfer_timer[i] =
-+ DWC_TIMER_ALLOC("hc timer", hc_xfer_timeout,
-+ &hcd->core_if->hc_xfer_info[i]);
-+#endif
-+ DWC_DEBUGPL(DBG_HCDV, "HCD Added channel #%d, hc=%p\n", i,
-+ channel);
-+ }
-+
-+ if (fiq_enable) {
-+ hcd->fiq_state = DWC_ALLOC(sizeof(struct fiq_state) + (sizeof(struct fiq_channel_state) * num_channels));
-+ if (!hcd->fiq_state) {
-+ retval = -DWC_E_NO_MEMORY;
-+ DWC_ERROR("%s: cannot allocate fiq_state structure\n", __func__);
-+ dwc_otg_hcd_free(hcd);
-+ goto out;
-+ }
-+ DWC_MEMSET(hcd->fiq_state, 0, (sizeof(struct fiq_state) + (sizeof(struct fiq_channel_state) * num_channels)));
-+
-+ for (i = 0; i < num_channels; i++) {
-+ hcd->fiq_state->channel[i].fsm = FIQ_PASSTHROUGH;
-+ }
-+ hcd->fiq_state->dummy_send = DWC_ALLOC_ATOMIC(16);
-+
-+ hcd->fiq_stack = DWC_ALLOC(sizeof(struct fiq_stack));
-+ if (!hcd->fiq_stack) {
-+ retval = -DWC_E_NO_MEMORY;
-+ DWC_ERROR("%s: cannot allocate fiq_stack structure\n", __func__);
-+ dwc_otg_hcd_free(hcd);
-+ goto out;
-+ }
-+ hcd->fiq_stack->magic1 = 0xDEADBEEF;
-+ hcd->fiq_stack->magic2 = 0xD00DFEED;
-+ hcd->fiq_state->gintmsk_saved.d32 = ~0;
-+ hcd->fiq_state->haintmsk_saved.b2.chint = ~0;
-+
-+ /* This bit is terrible and uses no API, but necessary. The FIQ has no concept of DMA pools
-+ * (and if it did, would be a lot slower). This allocates a chunk of memory (~9kiB for 8 host channels)
-+ * for use as transaction bounce buffers in a 2-D array. Our access into this chunk is done by some
-+ * moderately readable array casts.
-+ */
-+ hcd->fiq_dmab = DWC_DMA_ALLOC((sizeof(struct fiq_dma_channel) * num_channels), &hcd->fiq_state->dma_base);
-+ DWC_WARN("FIQ DMA bounce buffers: virt = 0x%08x dma = 0x%08x len=%d",
-+ (unsigned int)hcd->fiq_dmab, (unsigned int)hcd->fiq_state->dma_base,
-+ sizeof(struct fiq_dma_channel) * num_channels);
-+
-+ DWC_MEMSET(hcd->fiq_dmab, 0x6b, 9024);
-+
-+ /* pointer for debug in fiq_print */
-+ hcd->fiq_state->fiq_dmab = hcd->fiq_dmab;
-+ if (fiq_fsm_enable) {
-+ int i;
-+ for (i=0; i < hcd->core_if->core_params->host_channels; i++) {
-+ dwc_otg_cleanup_fiq_channel(hcd, i);
-+ }
-+ DWC_PRINTF("FIQ FSM acceleration enabled for :\n%s%s%s%s",
-+ (fiq_fsm_mask & 0x1) ? "Non-periodic Split Transactions\n" : "",
-+ (fiq_fsm_mask & 0x2) ? "Periodic Split Transactions\n" : "",
-+ (fiq_fsm_mask & 0x4) ? "High-Speed Isochronous Endpoints\n" : "",
-+ (fiq_fsm_mask & 0x8) ? "Interrupt/Control Split Transaction hack enabled\n" : "");
-+ }
-+ }
-+
-+ /* Initialize the Connection timeout timer. */
-+ hcd->conn_timer = DWC_TIMER_ALLOC("Connection timer",
-+ dwc_otg_hcd_connect_timeout, 0);
-+
-+ printk(KERN_DEBUG "dwc_otg: Microframe scheduler %s\n", microframe_schedule ? "enabled":"disabled");
-+ if (microframe_schedule)
-+ init_hcd_usecs(hcd);
-+
-+ /* Initialize reset tasklet. */
-+ hcd->reset_tasklet = DWC_TASK_ALLOC("reset_tasklet", reset_tasklet_func, hcd);
-+
-+ hcd->completion_tasklet = DWC_TASK_ALLOC("completion_tasklet",
-+ completion_tasklet_func, hcd);
-+#ifdef DWC_DEV_SRPCAP
-+ if (hcd->core_if->power_down == 2) {
-+ /* Initialize Power on timer for Host power up in case hibernation */
-+ hcd->core_if->pwron_timer = DWC_TIMER_ALLOC("PWRON TIMER",
-+ dwc_otg_hcd_power_up, core_if);
-+ }
-+#endif
-+
-+ /*
-+ * Allocate space for storing data on status transactions. Normally no
-+ * data is sent, but this space acts as a bit bucket. This must be
-+ * done after usb_add_hcd since that function allocates the DMA buffer
-+ * pool.
-+ */
-+ if (hcd->core_if->dma_enable) {
-+ hcd->status_buf =
-+ DWC_DMA_ALLOC(DWC_OTG_HCD_STATUS_BUF_SIZE,
-+ &hcd->status_buf_dma);
-+ } else {
-+ hcd->status_buf = DWC_ALLOC(DWC_OTG_HCD_STATUS_BUF_SIZE);
-+ }
-+ if (!hcd->status_buf) {
-+ retval = -DWC_E_NO_MEMORY;
-+ DWC_ERROR("%s: status_buf allocation failed\n", __func__);
-+ dwc_otg_hcd_free(hcd);
-+ goto out;
-+ }
-+
-+ hcd->otg_port = 1;
-+ hcd->frame_list = NULL;
-+ hcd->frame_list_dma = 0;
-+ hcd->periodic_qh_count = 0;
-+
-+ DWC_MEMSET(hcd->hub_port, 0, sizeof(hcd->hub_port));
-+#ifdef FIQ_DEBUG
-+ DWC_MEMSET(hcd->hub_port_alloc, -1, sizeof(hcd->hub_port_alloc));
-+#endif
-+
-+out:
-+ return retval;
-+}
-+
-+void dwc_otg_hcd_remove(dwc_otg_hcd_t * hcd)
-+{
-+ /* Turn off all host-specific interrupts. */
-+ dwc_otg_disable_host_interrupts(hcd->core_if);
-+
-+ dwc_otg_hcd_free(hcd);
-+}
-+
-+/**
-+ * Initializes dynamic portions of the DWC_otg HCD state.
-+ */
-+static void dwc_otg_hcd_reinit(dwc_otg_hcd_t * hcd)
-+{
-+ int num_channels;
-+ int i;
-+ dwc_hc_t *channel;
-+ dwc_hc_t *channel_tmp;
-+
-+ hcd->flags.d32 = 0;
-+
-+ hcd->non_periodic_qh_ptr = &hcd->non_periodic_sched_active;
-+ if (!microframe_schedule) {
-+ hcd->non_periodic_channels = 0;
-+ hcd->periodic_channels = 0;
-+ } else {
-+ hcd->available_host_channels = hcd->core_if->core_params->host_channels;
-+ }
-+ /*
-+ * Put all channels in the free channel list and clean up channel
-+ * states.
-+ */
-+ DWC_CIRCLEQ_FOREACH_SAFE(channel, channel_tmp,
-+ &hcd->free_hc_list, hc_list_entry) {
-+ DWC_CIRCLEQ_REMOVE(&hcd->free_hc_list, channel, hc_list_entry);
-+ }
-+
-+ num_channels = hcd->core_if->core_params->host_channels;
-+ for (i = 0; i < num_channels; i++) {
-+ channel = hcd->hc_ptr_array[i];
-+ DWC_CIRCLEQ_INSERT_TAIL(&hcd->free_hc_list, channel,
-+ hc_list_entry);
-+ dwc_otg_hc_cleanup(hcd->core_if, channel);
-+ }
-+
-+ /* Initialize the DWC core for host mode operation. */
-+ dwc_otg_core_host_init(hcd->core_if);
-+
-+ /* Set core_if's lock pointer to the hcd->lock */
-+ hcd->core_if->lock = hcd->lock;
-+}
-+
-+/**
-+ * Assigns transactions from a QTD to a free host channel and initializes the
-+ * host channel to perform the transactions. The host channel is removed from
-+ * the free list.
-+ *
-+ * @param hcd The HCD state structure.
-+ * @param qh Transactions from the first QTD for this QH are selected and
-+ * assigned to a free host channel.
-+ */
-+static void assign_and_init_hc(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh)
-+{
-+ dwc_hc_t *hc;
-+ dwc_otg_qtd_t *qtd;
-+ dwc_otg_hcd_urb_t *urb;
-+ void* ptr = NULL;
-+ uint32_t intr_enable;
-+ unsigned long flags;
-+ gintmsk_data_t gintmsk = { .d32 = 0, };
-+
-+ qtd = DWC_CIRCLEQ_FIRST(&qh->qtd_list);
-+
-+ urb = qtd->urb;
-+
-+ DWC_DEBUGPL(DBG_HCDV, "%s(%p,%p) - urb %x, actual_length %d\n", __func__, hcd, qh, (unsigned int)urb, urb->actual_length);
-+
-+ if (((urb->actual_length < 0) || (urb->actual_length > urb->length)) && !dwc_otg_hcd_is_pipe_in(&urb->pipe_info))
-+ urb->actual_length = urb->length;
-+
-+
-+ hc = DWC_CIRCLEQ_FIRST(&hcd->free_hc_list);
-+
-+ /* Remove the host channel from the free list. */
-+ DWC_CIRCLEQ_REMOVE_INIT(&hcd->free_hc_list, hc, hc_list_entry);
-+
-+ qh->channel = hc;
-+
-+ qtd->in_process = 1;
-+
-+ /*
-+ * Use usb_pipedevice to determine device address. This address is
-+ * 0 before the SET_ADDRESS command and the correct address afterward.
-+ */
-+ hc->dev_addr = dwc_otg_hcd_get_dev_addr(&urb->pipe_info);
-+ hc->ep_num = dwc_otg_hcd_get_ep_num(&urb->pipe_info);
-+ hc->speed = qh->dev_speed;
-+ hc->max_packet = dwc_max_packet(qh->maxp);
-+
-+ hc->xfer_started = 0;
-+ hc->halt_status = DWC_OTG_HC_XFER_NO_HALT_STATUS;
-+ hc->error_state = (qtd->error_count > 0);
-+ hc->halt_on_queue = 0;
-+ hc->halt_pending = 0;
-+ hc->requests = 0;
-+
-+ /*
-+ * The following values may be modified in the transfer type section
-+ * below. The xfer_len value may be reduced when the transfer is
-+ * started to accommodate the max widths of the XferSize and PktCnt
-+ * fields in the HCTSIZn register.
-+ */
-+
-+ hc->ep_is_in = (dwc_otg_hcd_is_pipe_in(&urb->pipe_info) != 0);
-+ if (hc->ep_is_in) {
-+ hc->do_ping = 0;
-+ } else {
-+ hc->do_ping = qh->ping_state;
-+ }
-+
-+ hc->data_pid_start = qh->data_toggle;
-+ hc->multi_count = 1;
-+
-+ if (hcd->core_if->dma_enable) {
-+ hc->xfer_buff = (uint8_t *) urb->dma + urb->actual_length;
-+
-+ /* For non-dword aligned case */
-+ if (((unsigned long)hc->xfer_buff & 0x3)
-+ && !hcd->core_if->dma_desc_enable) {
-+ ptr = (uint8_t *) urb->buf + urb->actual_length;
-+ }
-+ } else {
-+ hc->xfer_buff = (uint8_t *) urb->buf + urb->actual_length;
-+ }
-+ hc->xfer_len = urb->length - urb->actual_length;
-+ hc->xfer_count = 0;
-+
-+ /*
-+ * Set the split attributes
-+ */
-+ hc->do_split = 0;
-+ if (qh->do_split) {
-+ uint32_t hub_addr, port_addr;
-+ hc->do_split = 1;
-+ hc->xact_pos = qtd->isoc_split_pos;
-+ /* We don't need to do complete splits anymore */
-+// if(fiq_fsm_enable)
-+ if (0)
-+ hc->complete_split = qtd->complete_split = 0;
-+ else
-+ hc->complete_split = qtd->complete_split;
-+
-+ hcd->fops->hub_info(hcd, urb->priv, &hub_addr, &port_addr);
-+ hc->hub_addr = (uint8_t) hub_addr;
-+ hc->port_addr = (uint8_t) port_addr;
-+ }
-+
-+ switch (dwc_otg_hcd_get_pipe_type(&urb->pipe_info)) {
-+ case UE_CONTROL:
-+ hc->ep_type = DWC_OTG_EP_TYPE_CONTROL;
-+ switch (qtd->control_phase) {
-+ case DWC_OTG_CONTROL_SETUP:
-+ DWC_DEBUGPL(DBG_HCDV, " Control setup transaction\n");
-+ hc->do_ping = 0;
-+ hc->ep_is_in = 0;
-+ hc->data_pid_start = DWC_OTG_HC_PID_SETUP;
-+ if (hcd->core_if->dma_enable) {
-+ hc->xfer_buff = (uint8_t *) urb->setup_dma;
-+ } else {
-+ hc->xfer_buff = (uint8_t *) urb->setup_packet;
-+ }
-+ hc->xfer_len = 8;
-+ ptr = NULL;
-+ break;
-+ case DWC_OTG_CONTROL_DATA:
-+ DWC_DEBUGPL(DBG_HCDV, " Control data transaction\n");
-+ hc->data_pid_start = qtd->data_toggle;
-+ break;
-+ case DWC_OTG_CONTROL_STATUS:
-+ /*
-+ * Direction is opposite of data direction or IN if no
-+ * data.
-+ */
-+ DWC_DEBUGPL(DBG_HCDV, " Control status transaction\n");
-+ if (urb->length == 0) {
-+ hc->ep_is_in = 1;
-+ } else {
-+ hc->ep_is_in =
-+ dwc_otg_hcd_is_pipe_out(&urb->pipe_info);
-+ }
-+ if (hc->ep_is_in) {
-+ hc->do_ping = 0;
-+ }
-+
-+ hc->data_pid_start = DWC_OTG_HC_PID_DATA1;
-+
-+ hc->xfer_len = 0;
-+ if (hcd->core_if->dma_enable) {
-+ hc->xfer_buff = (uint8_t *) hcd->status_buf_dma;
-+ } else {
-+ hc->xfer_buff = (uint8_t *) hcd->status_buf;
-+ }
-+ ptr = NULL;
-+ break;
-+ }
-+ break;
-+ case UE_BULK:
-+ hc->ep_type = DWC_OTG_EP_TYPE_BULK;
-+ break;
-+ case UE_INTERRUPT:
-+ hc->ep_type = DWC_OTG_EP_TYPE_INTR;
-+ break;
-+ case UE_ISOCHRONOUS:
-+ {
-+ struct dwc_otg_hcd_iso_packet_desc *frame_desc;
-+
-+ hc->ep_type = DWC_OTG_EP_TYPE_ISOC;
-+
-+ if (hcd->core_if->dma_desc_enable)
-+ break;
-+
-+ frame_desc = &urb->iso_descs[qtd->isoc_frame_index];
-+
-+ frame_desc->status = 0;
-+
-+ if (hcd->core_if->dma_enable) {
-+ hc->xfer_buff = (uint8_t *) urb->dma;
-+ } else {
-+ hc->xfer_buff = (uint8_t *) urb->buf;
-+ }
-+ hc->xfer_buff +=
-+ frame_desc->offset + qtd->isoc_split_offset;
-+ hc->xfer_len =
-+ frame_desc->length - qtd->isoc_split_offset;
-+
-+ /* For non-dword aligned buffers */
-+ if (((unsigned long)hc->xfer_buff & 0x3)
-+ && hcd->core_if->dma_enable) {
-+ ptr =
-+ (uint8_t *) urb->buf + frame_desc->offset +
-+ qtd->isoc_split_offset;
-+ } else
-+ ptr = NULL;
-+
-+ if (hc->xact_pos == DWC_HCSPLIT_XACTPOS_ALL) {
-+ if (hc->xfer_len <= 188) {
-+ hc->xact_pos = DWC_HCSPLIT_XACTPOS_ALL;
-+ } else {
-+ hc->xact_pos =
-+ DWC_HCSPLIT_XACTPOS_BEGIN;
-+ }
-+ }
-+ }
-+ break;
-+ }
-+ /* non DWORD-aligned buffer case */
-+ if (ptr) {
-+ uint32_t buf_size;
-+ if (hc->ep_type != DWC_OTG_EP_TYPE_ISOC) {
-+ buf_size = hcd->core_if->core_params->max_transfer_size;
-+ } else {
-+ buf_size = 4096;
-+ }
-+ if (!qh->dw_align_buf) {
-+ qh->dw_align_buf = DWC_DMA_ALLOC_ATOMIC(buf_size,
-+ &qh->dw_align_buf_dma);
-+ if (!qh->dw_align_buf) {
-+ DWC_ERROR
-+ ("%s: Failed to allocate memory to handle "
-+ "non-dword aligned buffer case\n",
-+ __func__);
-+ return;
-+ }
-+ }
-+ if (!hc->ep_is_in) {
-+ dwc_memcpy(qh->dw_align_buf, ptr, hc->xfer_len);
-+ }
-+ hc->align_buff = qh->dw_align_buf_dma;
-+ } else {
-+ hc->align_buff = 0;
-+ }
-+
-+ if (hc->ep_type == DWC_OTG_EP_TYPE_INTR ||
-+ hc->ep_type == DWC_OTG_EP_TYPE_ISOC) {
-+ /*
-+ * This value may be modified when the transfer is started to
-+ * reflect the actual transfer length.
-+ */
-+ hc->multi_count = dwc_hb_mult(qh->maxp);
-+ }
-+
-+ if (hcd->core_if->dma_desc_enable)
-+ hc->desc_list_addr = qh->desc_list_dma;
-+
-+ dwc_otg_hc_init(hcd->core_if, hc);
-+
-+ local_irq_save(flags);
-+
-+ if (fiq_enable) {
-+ local_fiq_disable();
-+ fiq_fsm_spin_lock(&hcd->fiq_state->lock);
-+ }
-+
-+ /* Enable the top level host channel interrupt. */
-+ intr_enable = (1 << hc->hc_num);
-+ DWC_MODIFY_REG32(&hcd->core_if->host_if->host_global_regs->haintmsk, 0, intr_enable);
-+
-+ /* Make sure host channel interrupts are enabled. */
-+ gintmsk.b.hcintr = 1;
-+ DWC_MODIFY_REG32(&hcd->core_if->core_global_regs->gintmsk, 0, gintmsk.d32);
-+
-+ if (fiq_enable) {
-+ fiq_fsm_spin_unlock(&hcd->fiq_state->lock);
-+ local_fiq_enable();
-+ }
-+
-+ local_irq_restore(flags);
-+ hc->qh = qh;
-+}
-+
-+
-+/**
-+ * fiq_fsm_transaction_suitable() - Test a QH for compatibility with the FIQ
-+ * @qh: pointer to the endpoint's queue head
-+ *
-+ * Transaction start/end control flow is grafted onto the existing dwc_otg
-+ * mechanisms, to avoid spaghettifying the functions more than they already are.
-+ * This function's eligibility check is altered by debug parameter.
-+ *
-+ * Returns: 0 for unsuitable, 1 implies the FIQ can be enabled for this transaction.
-+ */
-+
-+int fiq_fsm_transaction_suitable(dwc_otg_qh_t *qh)
-+{
-+ if (qh->do_split) {
-+ switch (qh->ep_type) {
-+ case UE_CONTROL:
-+ case UE_BULK:
-+ if (fiq_fsm_mask & (1 << 0))
-+ return 1;
-+ break;
-+ case UE_INTERRUPT:
-+ case UE_ISOCHRONOUS:
-+ if (fiq_fsm_mask & (1 << 1))
-+ return 1;
-+ break;
-+ default:
-+ break;
-+ }
-+ } else if (qh->ep_type == UE_ISOCHRONOUS) {
-+ if (fiq_fsm_mask & (1 << 2)) {
-+ /* HS ISOCH support. We test for compatibility:
-+ * - DWORD aligned buffers
-+ * - Must be at least 2 transfers (otherwise pointless to use the FIQ)
-+ * If yes, then the fsm enqueue function will handle the state machine setup.
-+ */
-+ dwc_otg_qtd_t *qtd = DWC_CIRCLEQ_FIRST(&qh->qtd_list);
-+ dwc_otg_hcd_urb_t *urb = qtd->urb;
-+ struct dwc_otg_hcd_iso_packet_desc (*iso_descs)[0] = &urb->iso_descs;
-+ int nr_iso_frames = urb->packet_count;
-+ int i;
-+ uint32_t ptr;
-+
-+ if (nr_iso_frames < 2)
-+ return 0;
-+ for (i = 0; i < nr_iso_frames; i++) {
-+ ptr = urb->dma + iso_descs[i]->offset;
-+ if (ptr & 0x3) {
-+ printk_ratelimited("%s: Non-Dword aligned isochronous frame offset."
-+ " Cannot queue FIQ-accelerated transfer to device %d endpoint %d\n",
-+ __FUNCTION__, qh->channel->dev_addr, qh->channel->ep_num);
-+ return 0;
-+ }
-+ }
-+ return 1;
-+ }
-+ }
-+ return 0;
-+}
-+
-+/**
-+ * fiq_fsm_setup_periodic_dma() - Set up DMA bounce buffers
-+ * @hcd: Pointer to the dwc_otg_hcd struct
-+ * @qh: Pointer to the endpoint's queue head
-+ *
-+ * Periodic split transactions are transmitted modulo 188 bytes.
-+ * This necessitates slicing data up into buckets for isochronous out
-+ * and fixing up the DMA address for all IN transfers.
-+ *
-+ * Returns 1 if the DMA bounce buffers have been used, 0 if the default
-+ * HC buffer has been used.
-+ */
-+int fiq_fsm_setup_periodic_dma(dwc_otg_hcd_t *hcd, struct fiq_channel_state *st, dwc_otg_qh_t *qh)
-+ {
-+ int frame_length, i = 0;
-+ uint8_t *ptr = NULL;
-+ dwc_hc_t *hc = qh->channel;
-+ struct fiq_dma_blob *blob;
-+ struct dwc_otg_hcd_iso_packet_desc *frame_desc;
-+
-+ for (i = 0; i < 6; i++) {
-+ st->dma_info.slot_len[i] = 255;
-+ }
-+ st->dma_info.index = 0;
-+ i = 0;
-+ if (hc->ep_is_in) {
-+ /*
-+ * Set dma_regs to bounce buffer. FIQ will update the
-+ * state depending on transaction progress.
-+ */
-+ blob = (struct fiq_dma_blob *) hcd->fiq_state->dma_base;
-+ st->hcdma_copy.d32 = (uint32_t) &blob->channel[hc->hc_num].index[0].buf[0];
-+ /* Calculate the max number of CSPLITS such that the FIQ can time out
-+ * a transaction if it fails.
-+ */
-+ frame_length = st->hcchar_copy.b.mps;
-+ do {
-+ i++;
-+ frame_length -= 188;
-+ } while (frame_length >= 0);
-+ st->nrpackets = i;
-+ return 1;
-+ } else {
-+ if (qh->ep_type == UE_ISOCHRONOUS) {
-+
-+ dwc_otg_qtd_t *qtd = DWC_CIRCLEQ_FIRST(&qh->qtd_list);
-+
-+ frame_desc = &qtd->urb->iso_descs[qtd->isoc_frame_index];
-+ frame_length = frame_desc->length;
-+
-+ /* Virtual address for bounce buffers */
-+ blob = hcd->fiq_dmab;
-+
-+ ptr = qtd->urb->buf + frame_desc->offset;
-+ if (frame_length == 0) {
-+ /*
-+ * for isochronous transactions, we must still transmit a packet
-+ * even if the length is zero.
-+ */
-+ st->dma_info.slot_len[0] = 0;
-+ st->nrpackets = 1;
-+ } else {
-+ do {
-+ if (frame_length <= 188) {
-+ dwc_memcpy(&blob->channel[hc->hc_num].index[i].buf[0], ptr, frame_length);
-+ st->dma_info.slot_len[i] = frame_length;
-+ ptr += frame_length;
-+ } else {
-+ dwc_memcpy(&blob->channel[hc->hc_num].index[i].buf[0], ptr, 188);
-+ st->dma_info.slot_len[i] = 188;
-+ ptr += 188;
-+ }
-+ i++;
-+ frame_length -= 188;
-+ } while (frame_length > 0);
-+ st->nrpackets = i;
-+ }
-+ ptr = qtd->urb->buf + frame_desc->offset;
-+ /* Point the HC at the DMA address of the bounce buffers */
-+ blob = (struct fiq_dma_blob *) hcd->fiq_state->dma_base;
-+ st->hcdma_copy.d32 = (uint32_t) &blob->channel[hc->hc_num].index[0].buf[0];
-+
-+ /* fixup xfersize to the actual packet size */
-+ st->hctsiz_copy.b.pid = 0;
-+ st->hctsiz_copy.b.xfersize = st->dma_info.slot_len[0];
-+ return 1;
-+ } else {
-+ /* For interrupt, single OUT packet required, goes in the SSPLIT from hc_buff. */
-+ return 0;
-+ }
-+ }
-+}
-+
-+/*
-+ * Pushing a periodic request into the queue near the EOF1 point
-+ * in a microframe causes erroneous behaviour (frmovrun) interrupt.
-+ * Usually, the request goes out on the bus causing a transfer but
-+ * the core does not transfer the data to memory.
-+ * This guard interval (in number of 60MHz clocks) is required which
-+ * must cater for CPU latency between reading the value and enabling
-+ * the channel.
-+ */
-+#define PERIODIC_FRREM_BACKOFF 1000
-+
-+int fiq_fsm_queue_isoc_transaction(dwc_otg_hcd_t *hcd, dwc_otg_qh_t *qh)
-+{
-+ dwc_hc_t *hc = qh->channel;
-+ dwc_otg_hc_regs_t *hc_regs = hcd->core_if->host_if->hc_regs[hc->hc_num];
-+ dwc_otg_qtd_t *qtd = DWC_CIRCLEQ_FIRST(&qh->qtd_list);
-+ int frame;
-+ struct fiq_channel_state *st = &hcd->fiq_state->channel[hc->hc_num];
-+ int xfer_len, nrpackets;
-+ hcdma_data_t hcdma;
-+ hfnum_data_t hfnum;
-+
-+ if (st->fsm != FIQ_PASSTHROUGH)
-+ return 0;
-+
-+ st->nr_errors = 0;
-+
-+ st->hcchar_copy.d32 = 0;
-+ st->hcchar_copy.b.mps = hc->max_packet;
-+ st->hcchar_copy.b.epdir = hc->ep_is_in;
-+ st->hcchar_copy.b.devaddr = hc->dev_addr;
-+ st->hcchar_copy.b.epnum = hc->ep_num;
-+ st->hcchar_copy.b.eptype = hc->ep_type;
-+
-+ st->hcintmsk_copy.b.chhltd = 1;
-+
-+ frame = dwc_otg_hcd_get_frame_number(hcd);
-+ st->hcchar_copy.b.oddfrm = (frame & 0x1) ? 0 : 1;
-+
-+ st->hcchar_copy.b.lspddev = 0;
-+ /* Enable the channel later as a final register write. */
-+
-+ st->hcsplt_copy.d32 = 0;
-+
-+ st->hs_isoc_info.iso_desc = (struct dwc_otg_hcd_iso_packet_desc *) &qtd->urb->iso_descs;
-+ st->hs_isoc_info.nrframes = qtd->urb->packet_count;
-+ /* grab the next DMA address offset from the array */
-+ st->hcdma_copy.d32 = qtd->urb->dma;
-+ hcdma.d32 = st->hcdma_copy.d32 + st->hs_isoc_info.iso_desc[0].offset;
-+
-+ /* We need to set multi_count. This is a bit tricky - has to be set per-transaction as
-+ * the core needs to be told to send the correct number. Caution: for IN transfers,
-+ * this is always set to the maximum size of the endpoint. */
-+ xfer_len = st->hs_isoc_info.iso_desc[0].length;
-+ nrpackets = (xfer_len + st->hcchar_copy.b.mps - 1) / st->hcchar_copy.b.mps;
-+ if (nrpackets == 0)
-+ nrpackets = 1;
-+ st->hcchar_copy.b.multicnt = nrpackets;
-+ st->hctsiz_copy.b.pktcnt = nrpackets;
-+
-+ /* Initial PID also needs to be set */
-+ if (st->hcchar_copy.b.epdir == 0) {
-+ st->hctsiz_copy.b.xfersize = xfer_len;
-+ switch (st->hcchar_copy.b.multicnt) {
-+ case 1:
-+ st->hctsiz_copy.b.pid = DWC_PID_DATA0;
-+ break;
-+ case 2:
-+ case 3:
-+ st->hctsiz_copy.b.pid = DWC_PID_MDATA;
-+ break;
-+ }
-+
-+ } else {
-+ st->hctsiz_copy.b.xfersize = nrpackets * st->hcchar_copy.b.mps;
-+ switch (st->hcchar_copy.b.multicnt) {
-+ case 1:
-+ st->hctsiz_copy.b.pid = DWC_PID_DATA0;
-+ break;
-+ case 2:
-+ st->hctsiz_copy.b.pid = DWC_PID_DATA1;
-+ break;
-+ case 3:
-+ st->hctsiz_copy.b.pid = DWC_PID_DATA2;
-+ break;
-+ }
-+ }
-+
-+ st->hs_isoc_info.stride = qh->interval;
-+ st->uframe_sleeps = 0;
-+
-+ fiq_print(FIQDBG_INT, hcd->fiq_state, "FSMQ %01d ", hc->hc_num);
-+ fiq_print(FIQDBG_INT, hcd->fiq_state, "%08x", st->hcchar_copy.d32);
-+ fiq_print(FIQDBG_INT, hcd->fiq_state, "%08x", st->hctsiz_copy.d32);
-+ fiq_print(FIQDBG_INT, hcd->fiq_state, "%08x", st->hcdma_copy.d32);
-+ hfnum.d32 = DWC_READ_REG32(&hcd->core_if->host_if->host_global_regs->hfnum);
-+ local_fiq_disable();
-+ fiq_fsm_spin_lock(&hcd->fiq_state->lock);
-+ DWC_WRITE_REG32(&hc_regs->hctsiz, st->hctsiz_copy.d32);
-+ DWC_WRITE_REG32(&hc_regs->hcsplt, st->hcsplt_copy.d32);
-+ DWC_WRITE_REG32(&hc_regs->hcdma, st->hcdma_copy.d32);
-+ DWC_WRITE_REG32(&hc_regs->hcchar, st->hcchar_copy.d32);
-+ DWC_WRITE_REG32(&hc_regs->hcintmsk, st->hcintmsk_copy.d32);
-+ if (hfnum.b.frrem < PERIODIC_FRREM_BACKOFF) {
-+ /* Prevent queueing near EOF1. Bad things happen if a periodic
-+ * split transaction is queued very close to EOF. SOF interrupt handler
-+ * will wake this channel at the next interrupt.
-+ */
-+ st->fsm = FIQ_HS_ISOC_SLEEPING;
-+ st->uframe_sleeps = 1;
-+ } else {
-+ st->fsm = FIQ_HS_ISOC_TURBO;
-+ st->hcchar_copy.b.chen = 1;
-+ DWC_WRITE_REG32(&hc_regs->hcchar, st->hcchar_copy.d32);
-+ }
-+ mb();
-+ st->hcchar_copy.b.chen = 0;
-+ fiq_fsm_spin_unlock(&hcd->fiq_state->lock);
-+ local_fiq_enable();
-+ return 0;
-+}
-+
-+
-+/**
-+ * fiq_fsm_queue_split_transaction() - Set up a host channel and FIQ state
-+ * @hcd: Pointer to the dwc_otg_hcd struct
-+ * @qh: Pointer to the endpoint's queue head
-+ *
-+ * This overrides the dwc_otg driver's normal method of queueing a transaction.
-+ * Called from dwc_otg_hcd_queue_transactions(), this performs specific setup
-+ * for the nominated host channel.
-+ *
-+ * For periodic transfers, it also peeks at the FIQ state to see if an immediate
-+ * start is possible. If not, then the FIQ is left to start the transfer.
-+ */
-+int fiq_fsm_queue_split_transaction(dwc_otg_hcd_t *hcd, dwc_otg_qh_t *qh)
-+{
-+ int start_immediate = 1, i;
-+ hfnum_data_t hfnum;
-+ dwc_hc_t *hc = qh->channel;
-+ dwc_otg_hc_regs_t *hc_regs = hcd->core_if->host_if->hc_regs[hc->hc_num];
-+ /* Program HC registers, setup FIQ_state, examine FIQ if periodic, start transfer (not if uframe 5) */
-+ int hub_addr, port_addr, frame, uframe;
-+ struct fiq_channel_state *st = &hcd->fiq_state->channel[hc->hc_num];
-+
-+ if (st->fsm != FIQ_PASSTHROUGH)
-+ return 0;
-+ st->nr_errors = 0;
-+
-+ st->hcchar_copy.d32 = 0;
-+ st->hcchar_copy.b.mps = hc->max_packet;
-+ st->hcchar_copy.b.epdir = hc->ep_is_in;
-+ st->hcchar_copy.b.devaddr = hc->dev_addr;
-+ st->hcchar_copy.b.epnum = hc->ep_num;
-+ st->hcchar_copy.b.eptype = hc->ep_type;
-+ if (hc->ep_type & 0x1) {
-+ if (hc->ep_is_in)
-+ st->hcchar_copy.b.multicnt = 3;
-+ else
-+ /* Docs say set this to 1, but driver sets to 0! */
-+ st->hcchar_copy.b.multicnt = 0;
-+ } else {
-+ st->hcchar_copy.b.multicnt = 1;
-+ st->hcchar_copy.b.oddfrm = 0;
-+ }
-+ st->hcchar_copy.b.lspddev = (hc->speed == DWC_OTG_EP_SPEED_LOW) ? 1 : 0;
-+ /* Enable the channel later as a final register write. */
-+
-+ st->hcsplt_copy.d32 = 0;
-+ if(qh->do_split) {
-+ hcd->fops->hub_info(hcd, DWC_CIRCLEQ_FIRST(&qh->qtd_list)->urb->priv, &hub_addr, &port_addr);
-+ st->hcsplt_copy.b.compsplt = 0;
-+ st->hcsplt_copy.b.spltena = 1;
-+ // XACTPOS is for isoc-out only but needs initialising anyway.
-+ st->hcsplt_copy.b.xactpos = ISOC_XACTPOS_ALL;
-+ if((qh->ep_type == DWC_OTG_EP_TYPE_ISOC) && (!qh->ep_is_in)) {
-+ /* For packetsize 0 < L < 188, ISOC_XACTPOS_ALL.
-+ * for longer than this, ISOC_XACTPOS_BEGIN and the FIQ
-+ * will update as necessary.
-+ */
-+ if (hc->xfer_len > 188) {
-+ st->hcsplt_copy.b.xactpos = ISOC_XACTPOS_BEGIN;
-+ }
-+ }
-+ st->hcsplt_copy.b.hubaddr = (uint8_t) hub_addr;
-+ st->hcsplt_copy.b.prtaddr = (uint8_t) port_addr;
-+ st->hub_addr = hub_addr;
-+ st->port_addr = port_addr;
-+ }
-+
-+ st->hctsiz_copy.d32 = 0;
-+ st->hctsiz_copy.b.dopng = 0;
-+ st->hctsiz_copy.b.pid = hc->data_pid_start;
-+
-+ if (hc->ep_is_in || (hc->xfer_len > hc->max_packet)) {
-+ hc->xfer_len = hc->max_packet;
-+ } else if (!hc->ep_is_in && (hc->xfer_len > 188)) {
-+ hc->xfer_len = 188;
-+ }
-+ st->hctsiz_copy.b.xfersize = hc->xfer_len;
-+
-+ st->hctsiz_copy.b.pktcnt = 1;
-+
-+ if (hc->ep_type & 0x1) {
-+ /*
-+ * For potentially multi-packet transfers, must use the DMA bounce buffers. For IN transfers,
-+ * the DMA address is the address of the first 188byte slot buffer in the bounce buffer array.
-+ * For multi-packet OUT transfers, we need to copy the data into the bounce buffer array so the FIQ can punt
-+ * the right address out as necessary. hc->xfer_buff and hc->xfer_len have already been set
-+ * in assign_and_init_hc(), but this is for the eventual transaction completion only. The FIQ
-+ * must not touch internal driver state.
-+ */
-+ if(!fiq_fsm_setup_periodic_dma(hcd, st, qh)) {
-+ if (hc->align_buff) {
-+ st->hcdma_copy.d32 = hc->align_buff;
-+ } else {
-+ st->hcdma_copy.d32 = ((unsigned long) hc->xfer_buff & 0xFFFFFFFF);
-+ }
-+ }
-+ } else {
-+ if (hc->align_buff) {
-+ st->hcdma_copy.d32 = hc->align_buff;
-+ } else {
-+ st->hcdma_copy.d32 = ((unsigned long) hc->xfer_buff & 0xFFFFFFFF);
-+ }
-+ }
-+ /* The FIQ depends upon no other interrupts being enabled except channel halt.
-+ * Fixup channel interrupt mask. */
-+ st->hcintmsk_copy.d32 = 0;
-+ st->hcintmsk_copy.b.chhltd = 1;
-+ st->hcintmsk_copy.b.ahberr = 1;
-+
-+ /* Hack courtesy of FreeBSD: apparently forcing Interrupt Split transactions
-+ * as Control puts the transfer into the non-periodic request queue and the
-+ * non-periodic handler in the hub. Makes things lots easier.
-+ */
-+ if ((fiq_fsm_mask & 0x8) && hc->ep_type == UE_INTERRUPT) {
-+ st->hcchar_copy.b.multicnt = 0;
-+ st->hcchar_copy.b.oddfrm = 0;
-+ st->hcchar_copy.b.eptype = UE_CONTROL;
-+ if (hc->align_buff) {
-+ st->hcdma_copy.d32 = hc->align_buff;
-+ } else {
-+ st->hcdma_copy.d32 = ((unsigned long) hc->xfer_buff & 0xFFFFFFFF);
-+ }
-+ }
-+ DWC_WRITE_REG32(&hc_regs->hcdma, st->hcdma_copy.d32);
-+ DWC_WRITE_REG32(&hc_regs->hctsiz, st->hctsiz_copy.d32);
-+ DWC_WRITE_REG32(&hc_regs->hcsplt, st->hcsplt_copy.d32);
-+ DWC_WRITE_REG32(&hc_regs->hcchar, st->hcchar_copy.d32);
-+ DWC_WRITE_REG32(&hc_regs->hcintmsk, st->hcintmsk_copy.d32);
-+
-+ local_fiq_disable();
-+ fiq_fsm_spin_lock(&hcd->fiq_state->lock);
-+
-+ if (hc->ep_type & 0x1) {
-+ hfnum.d32 = DWC_READ_REG32(&hcd->core_if->host_if->host_global_regs->hfnum);
-+ frame = (hfnum.b.frnum & ~0x7) >> 3;
-+ uframe = hfnum.b.frnum & 0x7;
-+ if (hfnum.b.frrem < PERIODIC_FRREM_BACKOFF) {
-+ /* Prevent queueing near EOF1. Bad things happen if a periodic
-+ * split transaction is queued very close to EOF.
-+ */
-+ start_immediate = 0;
-+ } else if (uframe == 5) {
-+ start_immediate = 0;
-+ } else if (hc->ep_type == UE_ISOCHRONOUS && !hc->ep_is_in) {
-+ start_immediate = 0;
-+ } else if (hc->ep_is_in && fiq_fsm_too_late(hcd->fiq_state, hc->hc_num)) {
-+ start_immediate = 0;
-+ } else {
-+ /* Search through all host channels to determine if a transaction
-+ * is currently in progress */
-+ for (i = 0; i < hcd->core_if->core_params->host_channels; i++) {
-+ if (i == hc->hc_num || hcd->fiq_state->channel[i].fsm == FIQ_PASSTHROUGH)
-+ continue;
-+ switch (hcd->fiq_state->channel[i].fsm) {
-+ /* TT is reserved for channels that are in the middle of a periodic
-+ * split transaction.
-+ */
-+ case FIQ_PER_SSPLIT_STARTED:
-+ case FIQ_PER_CSPLIT_WAIT:
-+ case FIQ_PER_CSPLIT_NYET1:
-+ case FIQ_PER_CSPLIT_POLL:
-+ case FIQ_PER_ISO_OUT_ACTIVE:
-+ case FIQ_PER_ISO_OUT_LAST:
-+ if (hcd->fiq_state->channel[i].hub_addr == hub_addr &&
-+ hcd->fiq_state->channel[i].port_addr == port_addr) {
-+ start_immediate = 0;
-+ }
-+ break;
-+ default:
-+ break;
-+ }
-+ if (!start_immediate)
-+ break;
-+ }
-+ }
-+ }
-+ if ((fiq_fsm_mask & 0x8) && hc->ep_type == UE_INTERRUPT)
-+ start_immediate = 1;
-+
-+ fiq_print(FIQDBG_INT, hcd->fiq_state, "FSMQ %01d %01d", hc->hc_num, start_immediate);
-+ fiq_print(FIQDBG_INT, hcd->fiq_state, "%08d", hfnum.b.frrem);
-+ //fiq_print(FIQDBG_INT, hcd->fiq_state, "H:%02dP:%02d", hub_addr, port_addr);
-+ //fiq_print(FIQDBG_INT, hcd->fiq_state, "%08x", st->hctsiz_copy.d32);
-+ //fiq_print(FIQDBG_INT, hcd->fiq_state, "%08x", st->hcdma_copy.d32);
-+ switch (hc->ep_type) {
-+ case UE_CONTROL:
-+ case UE_BULK:
-+ st->fsm = FIQ_NP_SSPLIT_STARTED;
-+ break;
-+ case UE_ISOCHRONOUS:
-+ if (hc->ep_is_in) {
-+ if (start_immediate) {
-+ st->fsm = FIQ_PER_SSPLIT_STARTED;
-+ } else {
-+ st->fsm = FIQ_PER_SSPLIT_QUEUED;
-+ }
-+ } else {
-+ if (start_immediate) {
-+ /* Single-isoc OUT packets don't require FIQ involvement */
-+ if (st->nrpackets == 1) {
-+ st->fsm = FIQ_PER_ISO_OUT_LAST;
-+ } else {
-+ st->fsm = FIQ_PER_ISO_OUT_ACTIVE;
-+ }
-+ } else {
-+ st->fsm = FIQ_PER_ISO_OUT_PENDING;
-+ }
-+ }
-+ break;
-+ case UE_INTERRUPT:
-+ if (fiq_fsm_mask & 0x8) {
-+ st->fsm = FIQ_NP_SSPLIT_STARTED;
-+ } else if (start_immediate) {
-+ st->fsm = FIQ_PER_SSPLIT_STARTED;
-+ } else {
-+ st->fsm = FIQ_PER_SSPLIT_QUEUED;
-+ }
-+ default:
-+ break;
-+ }
-+ if (start_immediate) {
-+ /* Set the oddfrm bit as close as possible to actual queueing */
-+ frame = dwc_otg_hcd_get_frame_number(hcd);
-+ st->expected_uframe = (frame + 1) & 0x3FFF;
-+ st->hcchar_copy.b.oddfrm = (frame & 0x1) ? 0 : 1;
-+ st->hcchar_copy.b.chen = 1;
-+ DWC_WRITE_REG32(&hc_regs->hcchar, st->hcchar_copy.d32);
-+ }
-+ mb();
-+ fiq_fsm_spin_unlock(&hcd->fiq_state->lock);
-+ local_fiq_enable();
-+ return 0;
-+}
-+
-+
-+/**
-+ * This function selects transactions from the HCD transfer schedule and
-+ * assigns them to available host channels. It is called from HCD interrupt
-+ * handler functions.
-+ *
-+ * @param hcd The HCD state structure.
-+ *
-+ * @return The types of new transactions that were assigned to host channels.
-+ */
-+dwc_otg_transaction_type_e dwc_otg_hcd_select_transactions(dwc_otg_hcd_t * hcd)
-+{
-+ dwc_list_link_t *qh_ptr;
-+ dwc_otg_qh_t *qh;
-+ int num_channels;
-+ dwc_irqflags_t flags;
-+ dwc_spinlock_t *channel_lock = hcd->channel_lock;
-+ dwc_otg_transaction_type_e ret_val = DWC_OTG_TRANSACTION_NONE;
-+
-+#ifdef DEBUG_HOST_CHANNELS
-+ last_sel_trans_num_per_scheduled = 0;
-+ last_sel_trans_num_nonper_scheduled = 0;
-+ last_sel_trans_num_avail_hc_at_start = hcd->available_host_channels;
-+#endif /* DEBUG_HOST_CHANNELS */
-+
-+ /* Process entries in the periodic ready list. */
-+ qh_ptr = DWC_LIST_FIRST(&hcd->periodic_sched_ready);
-+
-+ while (qh_ptr != &hcd->periodic_sched_ready &&
-+ !DWC_CIRCLEQ_EMPTY(&hcd->free_hc_list)) {
-+
-+ qh = DWC_LIST_ENTRY(qh_ptr, dwc_otg_qh_t, qh_list_entry);
-+
-+ if (microframe_schedule) {
-+ // Make sure we leave one channel for non periodic transactions.
-+ DWC_SPINLOCK_IRQSAVE(channel_lock, &flags);
-+ if (hcd->available_host_channels <= 1) {
-+ DWC_SPINUNLOCK_IRQRESTORE(channel_lock, flags);
-+ break;
-+ }
-+ hcd->available_host_channels--;
-+ DWC_SPINUNLOCK_IRQRESTORE(channel_lock, flags);
-+#ifdef DEBUG_HOST_CHANNELS
-+ last_sel_trans_num_per_scheduled++;
-+#endif /* DEBUG_HOST_CHANNELS */
-+ }
-+ qh = DWC_LIST_ENTRY(qh_ptr, dwc_otg_qh_t, qh_list_entry);
-+ assign_and_init_hc(hcd, qh);
-+
-+ /*
-+ * Move the QH from the periodic ready schedule to the
-+ * periodic assigned schedule.
-+ */
-+ qh_ptr = DWC_LIST_NEXT(qh_ptr);
-+ DWC_SPINLOCK_IRQSAVE(channel_lock, &flags);
-+ DWC_LIST_MOVE_HEAD(&hcd->periodic_sched_assigned,
-+ &qh->qh_list_entry);
-+ DWC_SPINUNLOCK_IRQRESTORE(channel_lock, flags);
-+ }
-+
-+ /*
-+ * Process entries in the inactive portion of the non-periodic
-+ * schedule. Some free host channels may not be used if they are
-+ * reserved for periodic transfers.
-+ */
-+ qh_ptr = hcd->non_periodic_sched_inactive.next;
-+ num_channels = hcd->core_if->core_params->host_channels;
-+ while (qh_ptr != &hcd->non_periodic_sched_inactive &&
-+ (microframe_schedule || hcd->non_periodic_channels <
-+ num_channels - hcd->periodic_channels) &&
-+ !DWC_CIRCLEQ_EMPTY(&hcd->free_hc_list)) {
-+
-+ qh = DWC_LIST_ENTRY(qh_ptr, dwc_otg_qh_t, qh_list_entry);
-+ /*
-+ * Check to see if this is a NAK'd retransmit, in which case ignore for retransmission
-+ * we hold off on bulk retransmissions to reduce NAK interrupt overhead for full-speed
-+ * cheeky devices that just hold off using NAKs
-+ */
-+ if (fiq_enable && nak_holdoff && qh->do_split) {
-+ if (qh->nak_frame != 0xffff) {
-+ uint16_t next_frame = dwc_frame_num_inc(qh->nak_frame, (qh->ep_type == UE_BULK) ? nak_holdoff : 8);
-+ uint16_t frame = dwc_otg_hcd_get_frame_number(hcd);
-+ if (dwc_frame_num_le(frame, next_frame)) {
-+ if(dwc_frame_num_le(next_frame, hcd->fiq_state->next_sched_frame)) {
-+ hcd->fiq_state->next_sched_frame = next_frame;
-+ }
-+ qh_ptr = DWC_LIST_NEXT(qh_ptr);
-+ continue;
-+ } else {
-+ qh->nak_frame = 0xFFFF;
-+ }
-+ }
-+ }
-+
-+ if (microframe_schedule) {
-+ DWC_SPINLOCK_IRQSAVE(channel_lock, &flags);
-+ if (hcd->available_host_channels < 1) {
-+ DWC_SPINUNLOCK_IRQRESTORE(channel_lock, flags);
-+ break;
-+ }
-+ hcd->available_host_channels--;
-+ DWC_SPINUNLOCK_IRQRESTORE(channel_lock, flags);
-+#ifdef DEBUG_HOST_CHANNELS
-+ last_sel_trans_num_nonper_scheduled++;
-+#endif /* DEBUG_HOST_CHANNELS */
-+ }
-+
-+ assign_and_init_hc(hcd, qh);
-+
-+ /*
-+ * Move the QH from the non-periodic inactive schedule to the
-+ * non-periodic active schedule.
-+ */
-+ qh_ptr = DWC_LIST_NEXT(qh_ptr);
-+ DWC_SPINLOCK_IRQSAVE(channel_lock, &flags);
-+ DWC_LIST_MOVE_HEAD(&hcd->non_periodic_sched_active,
-+ &qh->qh_list_entry);
-+ DWC_SPINUNLOCK_IRQRESTORE(channel_lock, flags);
-+
-+
-+ if (!microframe_schedule)
-+ hcd->non_periodic_channels++;
-+ }
-+ /* we moved a non-periodic QH to the active schedule. If the inactive queue is empty,
-+ * stop the FIQ from kicking us. We could potentially still have elements here if we
-+ * ran out of host channels.
-+ */
-+ if (fiq_enable) {
-+ if (DWC_LIST_EMPTY(&hcd->non_periodic_sched_inactive)) {
-+ hcd->fiq_state->kick_np_queues = 0;
-+ } else {
-+ /* For each entry remaining in the NP inactive queue,
-+ * if this a NAK'd retransmit then don't set the kick flag.
-+ */
-+ if(nak_holdoff) {
-+ DWC_LIST_FOREACH(qh_ptr, &hcd->non_periodic_sched_inactive) {
-+ qh = DWC_LIST_ENTRY(qh_ptr, dwc_otg_qh_t, qh_list_entry);
-+ if (qh->nak_frame == 0xFFFF) {
-+ hcd->fiq_state->kick_np_queues = 1;
-+ }
-+ }
-+ }
-+ }
-+ }
-+ if(!DWC_LIST_EMPTY(&hcd->periodic_sched_assigned))
-+ ret_val |= DWC_OTG_TRANSACTION_PERIODIC;
-+
-+ if(!DWC_LIST_EMPTY(&hcd->non_periodic_sched_active))
-+ ret_val |= DWC_OTG_TRANSACTION_NON_PERIODIC;
-+
-+
-+#ifdef DEBUG_HOST_CHANNELS
-+ last_sel_trans_num_avail_hc_at_end = hcd->available_host_channels;
-+#endif /* DEBUG_HOST_CHANNELS */
-+ return ret_val;
-+}
-+
-+/**
-+ * Attempts to queue a single transaction request for a host channel
-+ * associated with either a periodic or non-periodic transfer. This function
-+ * assumes that there is space available in the appropriate request queue. For
-+ * an OUT transfer or SETUP transaction in Slave mode, it checks whether space
-+ * is available in the appropriate Tx FIFO.
-+ *
-+ * @param hcd The HCD state structure.
-+ * @param hc Host channel descriptor associated with either a periodic or
-+ * non-periodic transfer.
-+ * @param fifo_dwords_avail Number of DWORDs available in the periodic Tx
-+ * FIFO for periodic transfers or the non-periodic Tx FIFO for non-periodic
-+ * transfers.
-+ *
-+ * @return 1 if a request is queued and more requests may be needed to
-+ * complete the transfer, 0 if no more requests are required for this
-+ * transfer, -1 if there is insufficient space in the Tx FIFO.
-+ */
-+static int queue_transaction(dwc_otg_hcd_t * hcd,
-+ dwc_hc_t * hc, uint16_t fifo_dwords_avail)
-+{
-+ int retval;
-+
-+ if (hcd->core_if->dma_enable) {
-+ if (hcd->core_if->dma_desc_enable) {
-+ if (!hc->xfer_started
-+ || (hc->ep_type == DWC_OTG_EP_TYPE_ISOC)) {
-+ dwc_otg_hcd_start_xfer_ddma(hcd, hc->qh);
-+ hc->qh->ping_state = 0;
-+ }
-+ } else if (!hc->xfer_started) {
-+ if (fiq_fsm_enable && hc->error_state) {
-+ hcd->fiq_state->channel[hc->hc_num].nr_errors =
-+ DWC_CIRCLEQ_FIRST(&hc->qh->qtd_list)->error_count;
-+ hcd->fiq_state->channel[hc->hc_num].fsm =
-+ FIQ_PASSTHROUGH_ERRORSTATE;
-+ }
-+ dwc_otg_hc_start_transfer(hcd->core_if, hc);
-+ hc->qh->ping_state = 0;
-+ }
-+ retval = 0;
-+ } else if (hc->halt_pending) {
-+ /* Don't queue a request if the channel has been halted. */
-+ retval = 0;
-+ } else if (hc->halt_on_queue) {
-+ dwc_otg_hc_halt(hcd->core_if, hc, hc->halt_status);
-+ retval = 0;
-+ } else if (hc->do_ping) {
-+ if (!hc->xfer_started) {
-+ dwc_otg_hc_start_transfer(hcd->core_if, hc);
-+ }
-+ retval = 0;
-+ } else if (!hc->ep_is_in || hc->data_pid_start == DWC_OTG_HC_PID_SETUP) {
-+ if ((fifo_dwords_avail * 4) >= hc->max_packet) {
-+ if (!hc->xfer_started) {
-+ dwc_otg_hc_start_transfer(hcd->core_if, hc);
-+ retval = 1;
-+ } else {
-+ retval =
-+ dwc_otg_hc_continue_transfer(hcd->core_if,
-+ hc);
-+ }
-+ } else {
-+ retval = -1;
-+ }
-+ } else {
-+ if (!hc->xfer_started) {
-+ dwc_otg_hc_start_transfer(hcd->core_if, hc);
-+ retval = 1;
-+ } else {
-+ retval = dwc_otg_hc_continue_transfer(hcd->core_if, hc);
-+ }
-+ }
-+
-+ return retval;
-+}
-+
-+/**
-+ * Processes periodic channels for the next frame and queues transactions for
-+ * these channels to the DWC_otg controller. After queueing transactions, the
-+ * Periodic Tx FIFO Empty interrupt is enabled if there are more transactions
-+ * to queue as Periodic Tx FIFO or request queue space becomes available.
-+ * Otherwise, the Periodic Tx FIFO Empty interrupt is disabled.
-+ */
-+static void process_periodic_channels(dwc_otg_hcd_t * hcd)
-+{
-+ hptxsts_data_t tx_status;
-+ dwc_list_link_t *qh_ptr;
-+ dwc_otg_qh_t *qh;
-+ int status = 0;
-+ int no_queue_space = 0;
-+ int no_fifo_space = 0;
-+
-+ dwc_otg_host_global_regs_t *host_regs;
-+ host_regs = hcd->core_if->host_if->host_global_regs;
-+
-+ DWC_DEBUGPL(DBG_HCDV, "Queue periodic transactions\n");
-+#ifdef DEBUG
-+ tx_status.d32 = DWC_READ_REG32(&host_regs->hptxsts);
-+ DWC_DEBUGPL(DBG_HCDV,
-+ " P Tx Req Queue Space Avail (before queue): %d\n",
-+ tx_status.b.ptxqspcavail);
-+ DWC_DEBUGPL(DBG_HCDV, " P Tx FIFO Space Avail (before queue): %d\n",
-+ tx_status.b.ptxfspcavail);
-+#endif
-+
-+ qh_ptr = hcd->periodic_sched_assigned.next;
-+ while (qh_ptr != &hcd->periodic_sched_assigned) {
-+ tx_status.d32 = DWC_READ_REG32(&host_regs->hptxsts);
-+ if (tx_status.b.ptxqspcavail == 0) {
-+ no_queue_space = 1;
-+ break;
-+ }
-+
-+ qh = DWC_LIST_ENTRY(qh_ptr, dwc_otg_qh_t, qh_list_entry);
-+
-+ // Do not send a split start transaction any later than frame .6
-+ // Note, we have to schedule a periodic in .5 to make it go in .6
-+ if(fiq_fsm_enable && qh->do_split && ((dwc_otg_hcd_get_frame_number(hcd) + 1) & 7) > 6)
-+ {
-+ qh_ptr = qh_ptr->next;
-+ hcd->fiq_state->next_sched_frame = dwc_otg_hcd_get_frame_number(hcd) | 7;
-+ continue;
-+ }
-+
-+ if (fiq_fsm_enable && fiq_fsm_transaction_suitable(qh)) {
-+ if (qh->do_split)
-+ fiq_fsm_queue_split_transaction(hcd, qh);
-+ else
-+ fiq_fsm_queue_isoc_transaction(hcd, qh);
-+ } else {
-+
-+ /*
-+ * Set a flag if we're queueing high-bandwidth in slave mode.
-+ * The flag prevents any halts to get into the request queue in
-+ * the middle of multiple high-bandwidth packets getting queued.
-+ */
-+ if (!hcd->core_if->dma_enable && qh->channel->multi_count > 1) {
-+ hcd->core_if->queuing_high_bandwidth = 1;
-+ }
-+ status = queue_transaction(hcd, qh->channel,
-+ tx_status.b.ptxfspcavail);
-+ if (status < 0) {
-+ no_fifo_space = 1;
-+ break;
-+ }
-+ }
-+
-+ /*
-+ * In Slave mode, stay on the current transfer until there is
-+ * nothing more to do or the high-bandwidth request count is
-+ * reached. In DMA mode, only need to queue one request. The
-+ * controller automatically handles multiple packets for
-+ * high-bandwidth transfers.
-+ */
-+ if (hcd->core_if->dma_enable || status == 0 ||
-+ qh->channel->requests == qh->channel->multi_count) {
-+ qh_ptr = qh_ptr->next;
-+ /*
-+ * Move the QH from the periodic assigned schedule to
-+ * the periodic queued schedule.
-+ */
-+ DWC_LIST_MOVE_HEAD(&hcd->periodic_sched_queued,
-+ &qh->qh_list_entry);
-+
-+ /* done queuing high bandwidth */
-+ hcd->core_if->queuing_high_bandwidth = 0;
-+ }
-+ }
-+
-+ if (!hcd->core_if->dma_enable) {
-+ dwc_otg_core_global_regs_t *global_regs;
-+ gintmsk_data_t intr_mask = {.d32 = 0 };
-+
-+ global_regs = hcd->core_if->core_global_regs;
-+ intr_mask.b.ptxfempty = 1;
-+#ifdef DEBUG
-+ tx_status.d32 = DWC_READ_REG32(&host_regs->hptxsts);
-+ DWC_DEBUGPL(DBG_HCDV,
-+ " P Tx Req Queue Space Avail (after queue): %d\n",
-+ tx_status.b.ptxqspcavail);
-+ DWC_DEBUGPL(DBG_HCDV,
-+ " P Tx FIFO Space Avail (after queue): %d\n",
-+ tx_status.b.ptxfspcavail);
-+#endif
-+ if (!DWC_LIST_EMPTY(&hcd->periodic_sched_assigned) ||
-+ no_queue_space || no_fifo_space) {
-+ /*
-+ * May need to queue more transactions as the request
-+ * queue or Tx FIFO empties. Enable the periodic Tx
-+ * FIFO empty interrupt. (Always use the half-empty
-+ * level to ensure that new requests are loaded as
-+ * soon as possible.)
-+ */
-+ DWC_MODIFY_REG32(&global_regs->gintmsk, 0,
-+ intr_mask.d32);
-+ } else {
-+ /*
-+ * Disable the Tx FIFO empty interrupt since there are
-+ * no more transactions that need to be queued right
-+ * now. This function is called from interrupt
-+ * handlers to queue more transactions as transfer
-+ * states change.
-+ */
-+ DWC_MODIFY_REG32(&global_regs->gintmsk, intr_mask.d32,
-+ 0);
-+ }
-+ }
-+}
-+
-+/**
-+ * Processes active non-periodic channels and queues transactions for these
-+ * channels to the DWC_otg controller. After queueing transactions, the NP Tx
-+ * FIFO Empty interrupt is enabled if there are more transactions to queue as
-+ * NP Tx FIFO or request queue space becomes available. Otherwise, the NP Tx
-+ * FIFO Empty interrupt is disabled.
-+ */
-+static void process_non_periodic_channels(dwc_otg_hcd_t * hcd)
-+{
-+ gnptxsts_data_t tx_status;
-+ dwc_list_link_t *orig_qh_ptr;
-+ dwc_otg_qh_t *qh;
-+ int status;
-+ int no_queue_space = 0;
-+ int no_fifo_space = 0;
-+ int more_to_do = 0;
-+
-+ dwc_otg_core_global_regs_t *global_regs =
-+ hcd->core_if->core_global_regs;
-+
-+ DWC_DEBUGPL(DBG_HCDV, "Queue non-periodic transactions\n");
-+#ifdef DEBUG
-+ tx_status.d32 = DWC_READ_REG32(&global_regs->gnptxsts);
-+ DWC_DEBUGPL(DBG_HCDV,
-+ " NP Tx Req Queue Space Avail (before queue): %d\n",
-+ tx_status.b.nptxqspcavail);
-+ DWC_DEBUGPL(DBG_HCDV, " NP Tx FIFO Space Avail (before queue): %d\n",
-+ tx_status.b.nptxfspcavail);
-+#endif
-+ /*
-+ * Keep track of the starting point. Skip over the start-of-list
-+ * entry.
-+ */
-+ if (hcd->non_periodic_qh_ptr == &hcd->non_periodic_sched_active) {
-+ hcd->non_periodic_qh_ptr = hcd->non_periodic_qh_ptr->next;
-+ }
-+ orig_qh_ptr = hcd->non_periodic_qh_ptr;
-+
-+ /*
-+ * Process once through the active list or until no more space is
-+ * available in the request queue or the Tx FIFO.
-+ */
-+ do {
-+ tx_status.d32 = DWC_READ_REG32(&global_regs->gnptxsts);
-+ if (!hcd->core_if->dma_enable && tx_status.b.nptxqspcavail == 0) {
-+ no_queue_space = 1;
-+ break;
-+ }
-+
-+ qh = DWC_LIST_ENTRY(hcd->non_periodic_qh_ptr, dwc_otg_qh_t,
-+ qh_list_entry);
-+
-+ if(fiq_fsm_enable && fiq_fsm_transaction_suitable(qh)) {
-+ fiq_fsm_queue_split_transaction(hcd, qh);
-+ } else {
-+ status = queue_transaction(hcd, qh->channel,
-+ tx_status.b.nptxfspcavail);
-+
-+ if (status > 0) {
-+ more_to_do = 1;
-+ } else if (status < 0) {
-+ no_fifo_space = 1;
-+ break;
-+ }
-+ }
-+ /* Advance to next QH, skipping start-of-list entry. */
-+ hcd->non_periodic_qh_ptr = hcd->non_periodic_qh_ptr->next;
-+ if (hcd->non_periodic_qh_ptr == &hcd->non_periodic_sched_active) {
-+ hcd->non_periodic_qh_ptr =
-+ hcd->non_periodic_qh_ptr->next;
-+ }
-+
-+ } while (hcd->non_periodic_qh_ptr != orig_qh_ptr);
-+
-+ if (!hcd->core_if->dma_enable) {
-+ gintmsk_data_t intr_mask = {.d32 = 0 };
-+ intr_mask.b.nptxfempty = 1;
-+
-+#ifdef DEBUG
-+ tx_status.d32 = DWC_READ_REG32(&global_regs->gnptxsts);
-+ DWC_DEBUGPL(DBG_HCDV,
-+ " NP Tx Req Queue Space Avail (after queue): %d\n",
-+ tx_status.b.nptxqspcavail);
-+ DWC_DEBUGPL(DBG_HCDV,
-+ " NP Tx FIFO Space Avail (after queue): %d\n",
-+ tx_status.b.nptxfspcavail);
-+#endif
-+ if (more_to_do || no_queue_space || no_fifo_space) {
-+ /*
-+ * May need to queue more transactions as the request
-+ * queue or Tx FIFO empties. Enable the non-periodic
-+ * Tx FIFO empty interrupt. (Always use the half-empty
-+ * level to ensure that new requests are loaded as
-+ * soon as possible.)
-+ */
-+ DWC_MODIFY_REG32(&global_regs->gintmsk, 0,
-+ intr_mask.d32);
-+ } else {
-+ /*
-+ * Disable the Tx FIFO empty interrupt since there are
-+ * no more transactions that need to be queued right
-+ * now. This function is called from interrupt
-+ * handlers to queue more transactions as transfer
-+ * states change.
-+ */
-+ DWC_MODIFY_REG32(&global_regs->gintmsk, intr_mask.d32,
-+ 0);
-+ }
-+ }
-+}
-+
-+/**
-+ * This function processes the currently active host channels and queues
-+ * transactions for these channels to the DWC_otg controller. It is called
-+ * from HCD interrupt handler functions.
-+ *
-+ * @param hcd The HCD state structure.
-+ * @param tr_type The type(s) of transactions to queue (non-periodic,
-+ * periodic, or both).
-+ */
-+void dwc_otg_hcd_queue_transactions(dwc_otg_hcd_t * hcd,
-+ dwc_otg_transaction_type_e tr_type)
-+{
-+#ifdef DEBUG_SOF
-+ DWC_DEBUGPL(DBG_HCD, "Queue Transactions\n");
-+#endif
-+ /* Process host channels associated with periodic transfers. */
-+ if ((tr_type == DWC_OTG_TRANSACTION_PERIODIC ||
-+ tr_type == DWC_OTG_TRANSACTION_ALL) &&
-+ !DWC_LIST_EMPTY(&hcd->periodic_sched_assigned)) {
-+
-+ process_periodic_channels(hcd);
-+ }
-+
-+ /* Process host channels associated with non-periodic transfers. */
-+ if (tr_type == DWC_OTG_TRANSACTION_NON_PERIODIC ||
-+ tr_type == DWC_OTG_TRANSACTION_ALL) {
-+ if (!DWC_LIST_EMPTY(&hcd->non_periodic_sched_active)) {
-+ process_non_periodic_channels(hcd);
-+ } else {
-+ /*
-+ * Ensure NP Tx FIFO empty interrupt is disabled when
-+ * there are no non-periodic transfers to process.
-+ */
-+ gintmsk_data_t gintmsk = {.d32 = 0 };
-+ gintmsk.b.nptxfempty = 1;
-+
-+ if (fiq_enable) {
-+ local_fiq_disable();
-+ fiq_fsm_spin_lock(&hcd->fiq_state->lock);
-+ DWC_MODIFY_REG32(&hcd->core_if->core_global_regs->gintmsk, gintmsk.d32, 0);
-+ fiq_fsm_spin_unlock(&hcd->fiq_state->lock);
-+ local_fiq_enable();
-+ } else {
-+ DWC_MODIFY_REG32(&hcd->core_if->core_global_regs->gintmsk, gintmsk.d32, 0);
-+ }
-+ }
-+ }
-+}
-+
-+#ifdef DWC_HS_ELECT_TST
-+/*
-+ * Quick and dirty hack to implement the HS Electrical Test
-+ * SINGLE_STEP_GET_DEVICE_DESCRIPTOR feature.
-+ *
-+ * This code was copied from our userspace app "hset". It sends a
-+ * Get Device Descriptor control sequence in two parts, first the
-+ * Setup packet by itself, followed some time later by the In and
-+ * Ack packets. Rather than trying to figure out how to add this
-+ * functionality to the normal driver code, we just hijack the
-+ * hardware, using these two function to drive the hardware
-+ * directly.
-+ */
-+
-+static dwc_otg_core_global_regs_t *global_regs;
-+static dwc_otg_host_global_regs_t *hc_global_regs;
-+static dwc_otg_hc_regs_t *hc_regs;
-+static uint32_t *data_fifo;
-+
-+static void do_setup(void)
-+{
-+ gintsts_data_t gintsts;
-+ hctsiz_data_t hctsiz;
-+ hcchar_data_t hcchar;
-+ haint_data_t haint;
-+ hcint_data_t hcint;
-+
-+ /* Enable HAINTs */
-+ DWC_WRITE_REG32(&hc_global_regs->haintmsk, 0x0001);
-+
-+ /* Enable HCINTs */
-+ DWC_WRITE_REG32(&hc_regs->hcintmsk, 0x04a3);
-+
-+ /* Read GINTSTS */
-+ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts);
-+
-+ /* Read HAINT */
-+ haint.d32 = DWC_READ_REG32(&hc_global_regs->haint);
-+
-+ /* Read HCINT */
-+ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint);
-+
-+ /* Read HCCHAR */
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+
-+ /* Clear HCINT */
-+ DWC_WRITE_REG32(&hc_regs->hcint, hcint.d32);
-+
-+ /* Clear HAINT */
-+ DWC_WRITE_REG32(&hc_global_regs->haint, haint.d32);
-+
-+ /* Clear GINTSTS */
-+ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32);
-+
-+ /* Read GINTSTS */
-+ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts);
-+
-+ /*
-+ * Send Setup packet (Get Device Descriptor)
-+ */
-+
-+ /* Make sure channel is disabled */
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+ if (hcchar.b.chen) {
-+ hcchar.b.chdis = 1;
-+// hcchar.b.chen = 1;
-+ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32);
-+ //sleep(1);
-+ dwc_mdelay(1000);
-+
-+ /* Read GINTSTS */
-+ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts);
-+
-+ /* Read HAINT */
-+ haint.d32 = DWC_READ_REG32(&hc_global_regs->haint);
-+
-+ /* Read HCINT */
-+ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint);
-+
-+ /* Read HCCHAR */
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+
-+ /* Clear HCINT */
-+ DWC_WRITE_REG32(&hc_regs->hcint, hcint.d32);
-+
-+ /* Clear HAINT */
-+ DWC_WRITE_REG32(&hc_global_regs->haint, haint.d32);
-+
-+ /* Clear GINTSTS */
-+ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32);
-+
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+ }
-+
-+ /* Set HCTSIZ */
-+ hctsiz.d32 = 0;
-+ hctsiz.b.xfersize = 8;
-+ hctsiz.b.pktcnt = 1;
-+ hctsiz.b.pid = DWC_OTG_HC_PID_SETUP;
-+ DWC_WRITE_REG32(&hc_regs->hctsiz, hctsiz.d32);
-+
-+ /* Set HCCHAR */
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+ hcchar.b.eptype = DWC_OTG_EP_TYPE_CONTROL;
-+ hcchar.b.epdir = 0;
-+ hcchar.b.epnum = 0;
-+ hcchar.b.mps = 8;
-+ hcchar.b.chen = 1;
-+ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32);
-+
-+ /* Fill FIFO with Setup data for Get Device Descriptor */
-+ data_fifo = (uint32_t *) ((char *)global_regs + 0x1000);
-+ DWC_WRITE_REG32(data_fifo++, 0x01000680);
-+ DWC_WRITE_REG32(data_fifo++, 0x00080000);
-+
-+ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts);
-+
-+ /* Wait for host channel interrupt */
-+ do {
-+ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts);
-+ } while (gintsts.b.hcintr == 0);
-+
-+ /* Disable HCINTs */
-+ DWC_WRITE_REG32(&hc_regs->hcintmsk, 0x0000);
-+
-+ /* Disable HAINTs */
-+ DWC_WRITE_REG32(&hc_global_regs->haintmsk, 0x0000);
-+
-+ /* Read HAINT */
-+ haint.d32 = DWC_READ_REG32(&hc_global_regs->haint);
-+
-+ /* Read HCINT */
-+ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint);
-+
-+ /* Read HCCHAR */
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+
-+ /* Clear HCINT */
-+ DWC_WRITE_REG32(&hc_regs->hcint, hcint.d32);
-+
-+ /* Clear HAINT */
-+ DWC_WRITE_REG32(&hc_global_regs->haint, haint.d32);
-+
-+ /* Clear GINTSTS */
-+ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32);
-+
-+ /* Read GINTSTS */
-+ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts);
-+}
-+
-+static void do_in_ack(void)
-+{
-+ gintsts_data_t gintsts;
-+ hctsiz_data_t hctsiz;
-+ hcchar_data_t hcchar;
-+ haint_data_t haint;
-+ hcint_data_t hcint;
-+ host_grxsts_data_t grxsts;
-+
-+ /* Enable HAINTs */
-+ DWC_WRITE_REG32(&hc_global_regs->haintmsk, 0x0001);
-+
-+ /* Enable HCINTs */
-+ DWC_WRITE_REG32(&hc_regs->hcintmsk, 0x04a3);
-+
-+ /* Read GINTSTS */
-+ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts);
-+
-+ /* Read HAINT */
-+ haint.d32 = DWC_READ_REG32(&hc_global_regs->haint);
-+
-+ /* Read HCINT */
-+ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint);
-+
-+ /* Read HCCHAR */
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+
-+ /* Clear HCINT */
-+ DWC_WRITE_REG32(&hc_regs->hcint, hcint.d32);
-+
-+ /* Clear HAINT */
-+ DWC_WRITE_REG32(&hc_global_regs->haint, haint.d32);
-+
-+ /* Clear GINTSTS */
-+ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32);
-+
-+ /* Read GINTSTS */
-+ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts);
-+
-+ /*
-+ * Receive Control In packet
-+ */
-+
-+ /* Make sure channel is disabled */
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+ if (hcchar.b.chen) {
-+ hcchar.b.chdis = 1;
-+ hcchar.b.chen = 1;
-+ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32);
-+ //sleep(1);
-+ dwc_mdelay(1000);
-+
-+ /* Read GINTSTS */
-+ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts);
-+
-+ /* Read HAINT */
-+ haint.d32 = DWC_READ_REG32(&hc_global_regs->haint);
-+
-+ /* Read HCINT */
-+ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint);
-+
-+ /* Read HCCHAR */
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+
-+ /* Clear HCINT */
-+ DWC_WRITE_REG32(&hc_regs->hcint, hcint.d32);
-+
-+ /* Clear HAINT */
-+ DWC_WRITE_REG32(&hc_global_regs->haint, haint.d32);
-+
-+ /* Clear GINTSTS */
-+ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32);
-+
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+ }
-+
-+ /* Set HCTSIZ */
-+ hctsiz.d32 = 0;
-+ hctsiz.b.xfersize = 8;
-+ hctsiz.b.pktcnt = 1;
-+ hctsiz.b.pid = DWC_OTG_HC_PID_DATA1;
-+ DWC_WRITE_REG32(&hc_regs->hctsiz, hctsiz.d32);
-+
-+ /* Set HCCHAR */
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+ hcchar.b.eptype = DWC_OTG_EP_TYPE_CONTROL;
-+ hcchar.b.epdir = 1;
-+ hcchar.b.epnum = 0;
-+ hcchar.b.mps = 8;
-+ hcchar.b.chen = 1;
-+ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32);
-+
-+ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts);
-+
-+ /* Wait for receive status queue interrupt */
-+ do {
-+ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts);
-+ } while (gintsts.b.rxstsqlvl == 0);
-+
-+ /* Read RXSTS */
-+ grxsts.d32 = DWC_READ_REG32(&global_regs->grxstsp);
-+
-+ /* Clear RXSTSQLVL in GINTSTS */
-+ gintsts.d32 = 0;
-+ gintsts.b.rxstsqlvl = 1;
-+ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32);
-+
-+ switch (grxsts.b.pktsts) {
-+ case DWC_GRXSTS_PKTSTS_IN:
-+ /* Read the data into the host buffer */
-+ if (grxsts.b.bcnt > 0) {
-+ int i;
-+ int word_count = (grxsts.b.bcnt + 3) / 4;
-+
-+ data_fifo = (uint32_t *) ((char *)global_regs + 0x1000);
-+
-+ for (i = 0; i < word_count; i++) {
-+ (void)DWC_READ_REG32(data_fifo++);
-+ }
-+ }
-+ break;
-+
-+ default:
-+ break;
-+ }
-+
-+ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts);
-+
-+ /* Wait for receive status queue interrupt */
-+ do {
-+ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts);
-+ } while (gintsts.b.rxstsqlvl == 0);
-+
-+ /* Read RXSTS */
-+ grxsts.d32 = DWC_READ_REG32(&global_regs->grxstsp);
-+
-+ /* Clear RXSTSQLVL in GINTSTS */
-+ gintsts.d32 = 0;
-+ gintsts.b.rxstsqlvl = 1;
-+ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32);
-+
-+ switch (grxsts.b.pktsts) {
-+ case DWC_GRXSTS_PKTSTS_IN_XFER_COMP:
-+ break;
-+
-+ default:
-+ break;
-+ }
-+
-+ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts);
-+
-+ /* Wait for host channel interrupt */
-+ do {
-+ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts);
-+ } while (gintsts.b.hcintr == 0);
-+
-+ /* Read HAINT */
-+ haint.d32 = DWC_READ_REG32(&hc_global_regs->haint);
-+
-+ /* Read HCINT */
-+ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint);
-+
-+ /* Read HCCHAR */
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+
-+ /* Clear HCINT */
-+ DWC_WRITE_REG32(&hc_regs->hcint, hcint.d32);
-+
-+ /* Clear HAINT */
-+ DWC_WRITE_REG32(&hc_global_regs->haint, haint.d32);
-+
-+ /* Clear GINTSTS */
-+ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32);
-+
-+ /* Read GINTSTS */
-+ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts);
-+
-+// usleep(100000);
-+// mdelay(100);
-+ dwc_mdelay(1);
-+
-+ /*
-+ * Send handshake packet
-+ */
-+
-+ /* Read HAINT */
-+ haint.d32 = DWC_READ_REG32(&hc_global_regs->haint);
-+
-+ /* Read HCINT */
-+ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint);
-+
-+ /* Read HCCHAR */
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+
-+ /* Clear HCINT */
-+ DWC_WRITE_REG32(&hc_regs->hcint, hcint.d32);
-+
-+ /* Clear HAINT */
-+ DWC_WRITE_REG32(&hc_global_regs->haint, haint.d32);
-+
-+ /* Clear GINTSTS */
-+ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32);
-+
-+ /* Read GINTSTS */
-+ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts);
-+
-+ /* Make sure channel is disabled */
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+ if (hcchar.b.chen) {
-+ hcchar.b.chdis = 1;
-+ hcchar.b.chen = 1;
-+ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32);
-+ //sleep(1);
-+ dwc_mdelay(1000);
-+
-+ /* Read GINTSTS */
-+ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts);
-+
-+ /* Read HAINT */
-+ haint.d32 = DWC_READ_REG32(&hc_global_regs->haint);
-+
-+ /* Read HCINT */
-+ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint);
-+
-+ /* Read HCCHAR */
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+
-+ /* Clear HCINT */
-+ DWC_WRITE_REG32(&hc_regs->hcint, hcint.d32);
-+
-+ /* Clear HAINT */
-+ DWC_WRITE_REG32(&hc_global_regs->haint, haint.d32);
-+
-+ /* Clear GINTSTS */
-+ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32);
-+
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+ }
-+
-+ /* Set HCTSIZ */
-+ hctsiz.d32 = 0;
-+ hctsiz.b.xfersize = 0;
-+ hctsiz.b.pktcnt = 1;
-+ hctsiz.b.pid = DWC_OTG_HC_PID_DATA1;
-+ DWC_WRITE_REG32(&hc_regs->hctsiz, hctsiz.d32);
-+
-+ /* Set HCCHAR */
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+ hcchar.b.eptype = DWC_OTG_EP_TYPE_CONTROL;
-+ hcchar.b.epdir = 0;
-+ hcchar.b.epnum = 0;
-+ hcchar.b.mps = 8;
-+ hcchar.b.chen = 1;
-+ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32);
-+
-+ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts);
-+
-+ /* Wait for host channel interrupt */
-+ do {
-+ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts);
-+ } while (gintsts.b.hcintr == 0);
-+
-+ /* Disable HCINTs */
-+ DWC_WRITE_REG32(&hc_regs->hcintmsk, 0x0000);
-+
-+ /* Disable HAINTs */
-+ DWC_WRITE_REG32(&hc_global_regs->haintmsk, 0x0000);
-+
-+ /* Read HAINT */
-+ haint.d32 = DWC_READ_REG32(&hc_global_regs->haint);
-+
-+ /* Read HCINT */
-+ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint);
-+
-+ /* Read HCCHAR */
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+
-+ /* Clear HCINT */
-+ DWC_WRITE_REG32(&hc_regs->hcint, hcint.d32);
-+
-+ /* Clear HAINT */
-+ DWC_WRITE_REG32(&hc_global_regs->haint, haint.d32);
-+
-+ /* Clear GINTSTS */
-+ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32);
-+
-+ /* Read GINTSTS */
-+ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts);
-+}
-+#endif
-+
-+/** Handles hub class-specific requests. */
-+int dwc_otg_hcd_hub_control(dwc_otg_hcd_t * dwc_otg_hcd,
-+ uint16_t typeReq,
-+ uint16_t wValue,
-+ uint16_t wIndex, uint8_t * buf, uint16_t wLength)
-+{
-+ int retval = 0;
-+
-+ dwc_otg_core_if_t *core_if = dwc_otg_hcd->core_if;
-+ usb_hub_descriptor_t *hub_desc;
-+ hprt0_data_t hprt0 = {.d32 = 0 };
-+
-+ uint32_t port_status;
-+
-+ switch (typeReq) {
-+ case UCR_CLEAR_HUB_FEATURE:
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - "
-+ "ClearHubFeature 0x%x\n", wValue);
-+ switch (wValue) {
-+ case UHF_C_HUB_LOCAL_POWER:
-+ case UHF_C_HUB_OVER_CURRENT:
-+ /* Nothing required here */
-+ break;
-+ default:
-+ retval = -DWC_E_INVALID;
-+ DWC_ERROR("DWC OTG HCD - "
-+ "ClearHubFeature request %xh unknown\n",
-+ wValue);
-+ }
-+ break;
-+ case UCR_CLEAR_PORT_FEATURE:
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+ if (wValue != UHF_PORT_L1)
-+#endif
-+ if (!wIndex || wIndex > 1)
-+ goto error;
-+
-+ switch (wValue) {
-+ case UHF_PORT_ENABLE:
-+ DWC_DEBUGPL(DBG_ANY, "DWC OTG HCD HUB CONTROL - "
-+ "ClearPortFeature USB_PORT_FEAT_ENABLE\n");
-+ hprt0.d32 = dwc_otg_read_hprt0(core_if);
-+ hprt0.b.prtena = 1;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+ break;
-+ case UHF_PORT_SUSPEND:
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - "
-+ "ClearPortFeature USB_PORT_FEAT_SUSPEND\n");
-+
-+ if (core_if->power_down == 2) {
-+ dwc_otg_host_hibernation_restore(core_if, 0, 0);
-+ } else {
-+ DWC_WRITE_REG32(core_if->pcgcctl, 0);
-+ dwc_mdelay(5);
-+
-+ hprt0.d32 = dwc_otg_read_hprt0(core_if);
-+ hprt0.b.prtres = 1;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+ hprt0.b.prtsusp = 0;
-+ /* Clear Resume bit */
-+ dwc_mdelay(100);
-+ hprt0.b.prtres = 0;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+ }
-+ break;
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+ case UHF_PORT_L1:
-+ {
-+ pcgcctl_data_t pcgcctl = {.d32 = 0 };
-+ glpmcfg_data_t lpmcfg = {.d32 = 0 };
-+
-+ lpmcfg.d32 =
-+ DWC_READ_REG32(&core_if->
-+ core_global_regs->glpmcfg);
-+ lpmcfg.b.en_utmi_sleep = 0;
-+ lpmcfg.b.hird_thres &= (~(1 << 4));
-+ lpmcfg.b.prt_sleep_sts = 1;
-+ DWC_WRITE_REG32(&core_if->
-+ core_global_regs->glpmcfg,
-+ lpmcfg.d32);
-+
-+ /* Clear Enbl_L1Gating bit. */
-+ pcgcctl.b.enbl_sleep_gating = 1;
-+ DWC_MODIFY_REG32(core_if->pcgcctl, pcgcctl.d32,
-+ 0);
-+
-+ dwc_mdelay(5);
-+
-+ hprt0.d32 = dwc_otg_read_hprt0(core_if);
-+ hprt0.b.prtres = 1;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0,
-+ hprt0.d32);
-+ /* This bit will be cleared in wakeup interrupt handle */
-+ break;
-+ }
-+#endif
-+ case UHF_PORT_POWER:
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - "
-+ "ClearPortFeature USB_PORT_FEAT_POWER\n");
-+ hprt0.d32 = dwc_otg_read_hprt0(core_if);
-+ hprt0.b.prtpwr = 0;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+ break;
-+ case UHF_PORT_INDICATOR:
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - "
-+ "ClearPortFeature USB_PORT_FEAT_INDICATOR\n");
-+ /* Port inidicator not supported */
-+ break;
-+ case UHF_C_PORT_CONNECTION:
-+ /* Clears drivers internal connect status change
-+ * flag */
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - "
-+ "ClearPortFeature USB_PORT_FEAT_C_CONNECTION\n");
-+ dwc_otg_hcd->flags.b.port_connect_status_change = 0;
-+ break;
-+ case UHF_C_PORT_RESET:
-+ /* Clears the driver's internal Port Reset Change
-+ * flag */
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - "
-+ "ClearPortFeature USB_PORT_FEAT_C_RESET\n");
-+ dwc_otg_hcd->flags.b.port_reset_change = 0;
-+ break;
-+ case UHF_C_PORT_ENABLE:
-+ /* Clears the driver's internal Port
-+ * Enable/Disable Change flag */
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - "
-+ "ClearPortFeature USB_PORT_FEAT_C_ENABLE\n");
-+ dwc_otg_hcd->flags.b.port_enable_change = 0;
-+ break;
-+ case UHF_C_PORT_SUSPEND:
-+ /* Clears the driver's internal Port Suspend
-+ * Change flag, which is set when resume signaling on
-+ * the host port is complete */
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - "
-+ "ClearPortFeature USB_PORT_FEAT_C_SUSPEND\n");
-+ dwc_otg_hcd->flags.b.port_suspend_change = 0;
-+ break;
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+ case UHF_C_PORT_L1:
-+ dwc_otg_hcd->flags.b.port_l1_change = 0;
-+ break;
-+#endif
-+ case UHF_C_PORT_OVER_CURRENT:
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - "
-+ "ClearPortFeature USB_PORT_FEAT_C_OVER_CURRENT\n");
-+ dwc_otg_hcd->flags.b.port_over_current_change = 0;
-+ break;
-+ default:
-+ retval = -DWC_E_INVALID;
-+ DWC_ERROR("DWC OTG HCD - "
-+ "ClearPortFeature request %xh "
-+ "unknown or unsupported\n", wValue);
-+ }
-+ break;
-+ case UCR_GET_HUB_DESCRIPTOR:
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - "
-+ "GetHubDescriptor\n");
-+ hub_desc = (usb_hub_descriptor_t *) buf;
-+ hub_desc->bDescLength = 9;
-+ hub_desc->bDescriptorType = 0x29;
-+ hub_desc->bNbrPorts = 1;
-+ USETW(hub_desc->wHubCharacteristics, 0x08);
-+ hub_desc->bPwrOn2PwrGood = 1;
-+ hub_desc->bHubContrCurrent = 0;
-+ hub_desc->DeviceRemovable[0] = 0;
-+ hub_desc->DeviceRemovable[1] = 0xff;
-+ break;
-+ case UCR_GET_HUB_STATUS:
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - "
-+ "GetHubStatus\n");
-+ DWC_MEMSET(buf, 0, 4);
-+ break;
-+ case UCR_GET_PORT_STATUS:
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - "
-+ "GetPortStatus wIndex = 0x%04x FLAGS=0x%08x\n",
-+ wIndex, dwc_otg_hcd->flags.d32);
-+ if (!wIndex || wIndex > 1)
-+ goto error;
-+
-+ port_status = 0;
-+
-+ if (dwc_otg_hcd->flags.b.port_connect_status_change)
-+ port_status |= (1 << UHF_C_PORT_CONNECTION);
-+
-+ if (dwc_otg_hcd->flags.b.port_enable_change)
-+ port_status |= (1 << UHF_C_PORT_ENABLE);
-+
-+ if (dwc_otg_hcd->flags.b.port_suspend_change)
-+ port_status |= (1 << UHF_C_PORT_SUSPEND);
-+
-+ if (dwc_otg_hcd->flags.b.port_l1_change)
-+ port_status |= (1 << UHF_C_PORT_L1);
-+
-+ if (dwc_otg_hcd->flags.b.port_reset_change) {
-+ port_status |= (1 << UHF_C_PORT_RESET);
-+ }
-+
-+ if (dwc_otg_hcd->flags.b.port_over_current_change) {
-+ DWC_WARN("Overcurrent change detected\n");
-+ port_status |= (1 << UHF_C_PORT_OVER_CURRENT);
-+ }
-+
-+ if (!dwc_otg_hcd->flags.b.port_connect_status) {
-+ /*
-+ * The port is disconnected, which means the core is
-+ * either in device mode or it soon will be. Just
-+ * return 0's for the remainder of the port status
-+ * since the port register can't be read if the core
-+ * is in device mode.
-+ */
-+ *((__le32 *) buf) = dwc_cpu_to_le32(&port_status);
-+ break;
-+ }
-+
-+ hprt0.d32 = DWC_READ_REG32(core_if->host_if->hprt0);
-+ DWC_DEBUGPL(DBG_HCDV, " HPRT0: 0x%08x\n", hprt0.d32);
-+
-+ if (hprt0.b.prtconnsts)
-+ port_status |= (1 << UHF_PORT_CONNECTION);
-+
-+ if (hprt0.b.prtena)
-+ port_status |= (1 << UHF_PORT_ENABLE);
-+
-+ if (hprt0.b.prtsusp)
-+ port_status |= (1 << UHF_PORT_SUSPEND);
-+
-+ if (hprt0.b.prtovrcurract)
-+ port_status |= (1 << UHF_PORT_OVER_CURRENT);
-+
-+ if (hprt0.b.prtrst)
-+ port_status |= (1 << UHF_PORT_RESET);
-+
-+ if (hprt0.b.prtpwr)
-+ port_status |= (1 << UHF_PORT_POWER);
-+
-+ if (hprt0.b.prtspd == DWC_HPRT0_PRTSPD_HIGH_SPEED)
-+ port_status |= (1 << UHF_PORT_HIGH_SPEED);
-+ else if (hprt0.b.prtspd == DWC_HPRT0_PRTSPD_LOW_SPEED)
-+ port_status |= (1 << UHF_PORT_LOW_SPEED);
-+
-+ if (hprt0.b.prttstctl)
-+ port_status |= (1 << UHF_PORT_TEST);
-+ if (dwc_otg_get_lpm_portsleepstatus(dwc_otg_hcd->core_if)) {
-+ port_status |= (1 << UHF_PORT_L1);
-+ }
-+ /*
-+ For Synopsys HW emulation of Power down wkup_control asserts the
-+ hreset_n and prst_n on suspned. This causes the HPRT0 to be zero.
-+ We intentionally tell the software that port is in L2Suspend state.
-+ Only for STE.
-+ */
-+ if ((core_if->power_down == 2)
-+ && (core_if->hibernation_suspend == 1)) {
-+ port_status |= (1 << UHF_PORT_SUSPEND);
-+ }
-+ /* USB_PORT_FEAT_INDICATOR unsupported always 0 */
-+
-+ *((__le32 *) buf) = dwc_cpu_to_le32(&port_status);
-+
-+ break;
-+ case UCR_SET_HUB_FEATURE:
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - "
-+ "SetHubFeature\n");
-+ /* No HUB features supported */
-+ break;
-+ case UCR_SET_PORT_FEATURE:
-+ if (wValue != UHF_PORT_TEST && (!wIndex || wIndex > 1))
-+ goto error;
-+
-+ if (!dwc_otg_hcd->flags.b.port_connect_status) {
-+ /*
-+ * The port is disconnected, which means the core is
-+ * either in device mode or it soon will be. Just
-+ * return without doing anything since the port
-+ * register can't be written if the core is in device
-+ * mode.
-+ */
-+ break;
-+ }
-+
-+ switch (wValue) {
-+ case UHF_PORT_SUSPEND:
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - "
-+ "SetPortFeature - USB_PORT_FEAT_SUSPEND\n");
-+ if (dwc_otg_hcd_otg_port(dwc_otg_hcd) != wIndex) {
-+ goto error;
-+ }
-+ if (core_if->power_down == 2) {
-+ int timeout = 300;
-+ dwc_irqflags_t flags;
-+ pcgcctl_data_t pcgcctl = {.d32 = 0 };
-+ gpwrdn_data_t gpwrdn = {.d32 = 0 };
-+ gusbcfg_data_t gusbcfg = {.d32 = 0 };
-+#ifdef DWC_DEV_SRPCAP
-+ int32_t otg_cap_param = core_if->core_params->otg_cap;
-+#endif
-+ DWC_PRINTF("Preparing for complete power-off\n");
-+
-+ /* Save registers before hibernation */
-+ dwc_otg_save_global_regs(core_if);
-+ dwc_otg_save_host_regs(core_if);
-+
-+ hprt0.d32 = dwc_otg_read_hprt0(core_if);
-+ hprt0.b.prtsusp = 1;
-+ hprt0.b.prtena = 0;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+ /* Spin hprt0.b.prtsusp to became 1 */
-+ do {
-+ hprt0.d32 = dwc_otg_read_hprt0(core_if);
-+ if (hprt0.b.prtsusp) {
-+ break;
-+ }
-+ dwc_mdelay(1);
-+ } while (--timeout);
-+ if (!timeout) {
-+ DWC_WARN("Suspend wasn't genereted\n");
-+ }
-+ dwc_udelay(10);
-+
-+ /*
-+ * We need to disable interrupts to prevent servicing of any IRQ
-+ * during going to hibernation
-+ */
-+ DWC_SPINLOCK_IRQSAVE(dwc_otg_hcd->lock, &flags);
-+ core_if->lx_state = DWC_OTG_L2;
-+#ifdef DWC_DEV_SRPCAP
-+ hprt0.d32 = dwc_otg_read_hprt0(core_if);
-+ hprt0.b.prtpwr = 0;
-+ hprt0.b.prtena = 0;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0,
-+ hprt0.d32);
-+#endif
-+ gusbcfg.d32 =
-+ DWC_READ_REG32(&core_if->core_global_regs->
-+ gusbcfg);
-+ if (gusbcfg.b.ulpi_utmi_sel == 1) {
-+ /* ULPI interface */
-+ /* Suspend the Phy Clock */
-+ pcgcctl.d32 = 0;
-+ pcgcctl.b.stoppclk = 1;
-+ DWC_MODIFY_REG32(core_if->pcgcctl, 0,
-+ pcgcctl.d32);
-+ dwc_udelay(10);
-+ gpwrdn.b.pmuactv = 1;
-+ DWC_MODIFY_REG32(&core_if->
-+ core_global_regs->
-+ gpwrdn, 0, gpwrdn.d32);
-+ } else {
-+ /* UTMI+ Interface */
-+ gpwrdn.b.pmuactv = 1;
-+ DWC_MODIFY_REG32(&core_if->
-+ core_global_regs->
-+ gpwrdn, 0, gpwrdn.d32);
-+ dwc_udelay(10);
-+ pcgcctl.b.stoppclk = 1;
-+ DWC_MODIFY_REG32(core_if->pcgcctl, 0, pcgcctl.d32);
-+ dwc_udelay(10);
-+ }
-+#ifdef DWC_DEV_SRPCAP
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.dis_vbus = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->
-+ gpwrdn, 0, gpwrdn.d32);
-+#endif
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuintsel = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->
-+ gpwrdn, 0, gpwrdn.d32);
-+ dwc_udelay(10);
-+
-+ gpwrdn.d32 = 0;
-+#ifdef DWC_DEV_SRPCAP
-+ gpwrdn.b.srp_det_msk = 1;
-+#endif
-+ gpwrdn.b.disconn_det_msk = 1;
-+ gpwrdn.b.lnstchng_msk = 1;
-+ gpwrdn.b.sts_chngint_msk = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->
-+ gpwrdn, 0, gpwrdn.d32);
-+ dwc_udelay(10);
-+
-+ /* Enable Power Down Clamp and all interrupts in GPWRDN */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnclmp = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->
-+ gpwrdn, 0, gpwrdn.d32);
-+ dwc_udelay(10);
-+
-+ /* Switch off VDD */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pwrdnswtch = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->
-+ gpwrdn, 0, gpwrdn.d32);
-+
-+#ifdef DWC_DEV_SRPCAP
-+ if (otg_cap_param == DWC_OTG_CAP_PARAM_HNP_SRP_CAPABLE)
-+ {
-+ core_if->pwron_timer_started = 1;
-+ DWC_TIMER_SCHEDULE(core_if->pwron_timer, 6000 /* 6 secs */ );
-+ }
-+#endif
-+ /* Save gpwrdn register for further usage if stschng interrupt */
-+ core_if->gr_backup->gpwrdn_local =
-+ DWC_READ_REG32(&core_if->core_global_regs->gpwrdn);
-+
-+ /* Set flag to indicate that we are in hibernation */
-+ core_if->hibernation_suspend = 1;
-+ DWC_SPINUNLOCK_IRQRESTORE(dwc_otg_hcd->lock,flags);
-+
-+ DWC_PRINTF("Host hibernation completed\n");
-+ // Exit from case statement
-+ break;
-+
-+ }
-+ if (dwc_otg_hcd_otg_port(dwc_otg_hcd) == wIndex &&
-+ dwc_otg_hcd->fops->get_b_hnp_enable(dwc_otg_hcd)) {
-+ gotgctl_data_t gotgctl = {.d32 = 0 };
-+ gotgctl.b.hstsethnpen = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->
-+ gotgctl, 0, gotgctl.d32);
-+ core_if->op_state = A_SUSPEND;
-+ }
-+ hprt0.d32 = dwc_otg_read_hprt0(core_if);
-+ hprt0.b.prtsusp = 1;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+ {
-+ dwc_irqflags_t flags;
-+ /* Update lx_state */
-+ DWC_SPINLOCK_IRQSAVE(dwc_otg_hcd->lock, &flags);
-+ core_if->lx_state = DWC_OTG_L2;
-+ DWC_SPINUNLOCK_IRQRESTORE(dwc_otg_hcd->lock, flags);
-+ }
-+ /* Suspend the Phy Clock */
-+ {
-+ pcgcctl_data_t pcgcctl = {.d32 = 0 };
-+ pcgcctl.b.stoppclk = 1;
-+ DWC_MODIFY_REG32(core_if->pcgcctl, 0,
-+ pcgcctl.d32);
-+ dwc_udelay(10);
-+ }
-+
-+ /* For HNP the bus must be suspended for at least 200ms. */
-+ if (dwc_otg_hcd->fops->get_b_hnp_enable(dwc_otg_hcd)) {
-+ pcgcctl_data_t pcgcctl = {.d32 = 0 };
-+ pcgcctl.b.stoppclk = 1;
-+ DWC_MODIFY_REG32(core_if->pcgcctl, pcgcctl.d32, 0);
-+ dwc_mdelay(200);
-+ }
-+
-+ /** @todo - check how sw can wait for 1 sec to check asesvld??? */
-+#if 0 //vahrama !!!!!!!!!!!!!!!!!!
-+ if (core_if->adp_enable) {
-+ gotgctl_data_t gotgctl = {.d32 = 0 };
-+ gpwrdn_data_t gpwrdn;
-+
-+ while (gotgctl.b.asesvld == 1) {
-+ gotgctl.d32 =
-+ DWC_READ_REG32(&core_if->
-+ core_global_regs->
-+ gotgctl);
-+ dwc_mdelay(100);
-+ }
-+
-+ /* Enable Power Down Logic */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuactv = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->
-+ gpwrdn, 0, gpwrdn.d32);
-+
-+ /* Unmask SRP detected interrupt from Power Down Logic */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.srp_det_msk = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->
-+ gpwrdn, 0, gpwrdn.d32);
-+
-+ dwc_otg_adp_probe_start(core_if);
-+ }
-+#endif
-+ break;
-+ case UHF_PORT_POWER:
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - "
-+ "SetPortFeature - USB_PORT_FEAT_POWER\n");
-+ hprt0.d32 = dwc_otg_read_hprt0(core_if);
-+ hprt0.b.prtpwr = 1;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+ break;
-+ case UHF_PORT_RESET:
-+ if ((core_if->power_down == 2)
-+ && (core_if->hibernation_suspend == 1)) {
-+ /* If we are going to exit from Hibernated
-+ * state via USB RESET.
-+ */
-+ dwc_otg_host_hibernation_restore(core_if, 0, 1);
-+ } else {
-+ hprt0.d32 = dwc_otg_read_hprt0(core_if);
-+
-+ DWC_DEBUGPL(DBG_HCD,
-+ "DWC OTG HCD HUB CONTROL - "
-+ "SetPortFeature - USB_PORT_FEAT_RESET\n");
-+ {
-+ pcgcctl_data_t pcgcctl = {.d32 = 0 };
-+ pcgcctl.b.enbl_sleep_gating = 1;
-+ pcgcctl.b.stoppclk = 1;
-+ DWC_MODIFY_REG32(core_if->pcgcctl, pcgcctl.d32, 0);
-+ DWC_WRITE_REG32(core_if->pcgcctl, 0);
-+ }
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+ {
-+ glpmcfg_data_t lpmcfg;
-+ lpmcfg.d32 =
-+ DWC_READ_REG32(&core_if->core_global_regs->glpmcfg);
-+ if (lpmcfg.b.prt_sleep_sts) {
-+ lpmcfg.b.en_utmi_sleep = 0;
-+ lpmcfg.b.hird_thres &= (~(1 << 4));
-+ DWC_WRITE_REG32
-+ (&core_if->core_global_regs->glpmcfg,
-+ lpmcfg.d32);
-+ dwc_mdelay(1);
-+ }
-+ }
-+#endif
-+ hprt0.d32 = dwc_otg_read_hprt0(core_if);
-+ /* Clear suspend bit if resetting from suspended state. */
-+ hprt0.b.prtsusp = 0;
-+ /* When B-Host the Port reset bit is set in
-+ * the Start HCD Callback function, so that
-+ * the reset is started within 1ms of the HNP
-+ * success interrupt. */
-+ if (!dwc_otg_hcd_is_b_host(dwc_otg_hcd)) {
-+ hprt0.b.prtpwr = 1;
-+ hprt0.b.prtrst = 1;
-+ DWC_PRINTF("Indeed it is in host mode hprt0 = %08x\n",hprt0.d32);
-+ DWC_WRITE_REG32(core_if->host_if->hprt0,
-+ hprt0.d32);
-+ }
-+ /* Clear reset bit in 10ms (FS/LS) or 50ms (HS) */
-+ dwc_mdelay(60);
-+ hprt0.b.prtrst = 0;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+ core_if->lx_state = DWC_OTG_L0; /* Now back to the on state */
-+ }
-+ break;
-+#ifdef DWC_HS_ELECT_TST
-+ case UHF_PORT_TEST:
-+ {
-+ uint32_t t;
-+ gintmsk_data_t gintmsk;
-+
-+ t = (wIndex >> 8); /* MSB wIndex USB */
-+ DWC_DEBUGPL(DBG_HCD,
-+ "DWC OTG HCD HUB CONTROL - "
-+ "SetPortFeature - USB_PORT_FEAT_TEST %d\n",
-+ t);
-+ DWC_WARN("USB_PORT_FEAT_TEST %d\n", t);
-+ if (t < 6) {
-+ hprt0.d32 = dwc_otg_read_hprt0(core_if);
-+ hprt0.b.prttstctl = t;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0,
-+ hprt0.d32);
-+ } else {
-+ /* Setup global vars with reg addresses (quick and
-+ * dirty hack, should be cleaned up)
-+ */
-+ global_regs = core_if->core_global_regs;
-+ hc_global_regs =
-+ core_if->host_if->host_global_regs;
-+ hc_regs =
-+ (dwc_otg_hc_regs_t *) ((char *)
-+ global_regs +
-+ 0x500);
-+ data_fifo =
-+ (uint32_t *) ((char *)global_regs +
-+ 0x1000);
-+
-+ if (t == 6) { /* HS_HOST_PORT_SUSPEND_RESUME */
-+ /* Save current interrupt mask */
-+ gintmsk.d32 =
-+ DWC_READ_REG32
-+ (&global_regs->gintmsk);
-+
-+ /* Disable all interrupts while we muck with
-+ * the hardware directly
-+ */
-+ DWC_WRITE_REG32(&global_regs->gintmsk, 0);
-+
-+ /* 15 second delay per the test spec */
-+ dwc_mdelay(15000);
-+
-+ /* Drive suspend on the root port */
-+ hprt0.d32 =
-+ dwc_otg_read_hprt0(core_if);
-+ hprt0.b.prtsusp = 1;
-+ hprt0.b.prtres = 0;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+
-+ /* 15 second delay per the test spec */
-+ dwc_mdelay(15000);
-+
-+ /* Drive resume on the root port */
-+ hprt0.d32 =
-+ dwc_otg_read_hprt0(core_if);
-+ hprt0.b.prtsusp = 0;
-+ hprt0.b.prtres = 1;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+ dwc_mdelay(100);
-+
-+ /* Clear the resume bit */
-+ hprt0.b.prtres = 0;
-+ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32);
-+
-+ /* Restore interrupts */
-+ DWC_WRITE_REG32(&global_regs->gintmsk, gintmsk.d32);
-+ } else if (t == 7) { /* SINGLE_STEP_GET_DEVICE_DESCRIPTOR setup */
-+ /* Save current interrupt mask */
-+ gintmsk.d32 =
-+ DWC_READ_REG32
-+ (&global_regs->gintmsk);
-+
-+ /* Disable all interrupts while we muck with
-+ * the hardware directly
-+ */
-+ DWC_WRITE_REG32(&global_regs->gintmsk, 0);
-+
-+ /* 15 second delay per the test spec */
-+ dwc_mdelay(15000);
-+
-+ /* Send the Setup packet */
-+ do_setup();
-+
-+ /* 15 second delay so nothing else happens for awhile */
-+ dwc_mdelay(15000);
-+
-+ /* Restore interrupts */
-+ DWC_WRITE_REG32(&global_regs->gintmsk, gintmsk.d32);
-+ } else if (t == 8) { /* SINGLE_STEP_GET_DEVICE_DESCRIPTOR execute */
-+ /* Save current interrupt mask */
-+ gintmsk.d32 =
-+ DWC_READ_REG32
-+ (&global_regs->gintmsk);
-+
-+ /* Disable all interrupts while we muck with
-+ * the hardware directly
-+ */
-+ DWC_WRITE_REG32(&global_regs->gintmsk, 0);
-+
-+ /* Send the Setup packet */
-+ do_setup();
-+
-+ /* 15 second delay so nothing else happens for awhile */
-+ dwc_mdelay(15000);
-+
-+ /* Send the In and Ack packets */
-+ do_in_ack();
-+
-+ /* 15 second delay so nothing else happens for awhile */
-+ dwc_mdelay(15000);
-+
-+ /* Restore interrupts */
-+ DWC_WRITE_REG32(&global_regs->gintmsk, gintmsk.d32);
-+ }
-+ }
-+ break;
-+ }
-+#endif /* DWC_HS_ELECT_TST */
-+
-+ case UHF_PORT_INDICATOR:
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - "
-+ "SetPortFeature - USB_PORT_FEAT_INDICATOR\n");
-+ /* Not supported */
-+ break;
-+ default:
-+ retval = -DWC_E_INVALID;
-+ DWC_ERROR("DWC OTG HCD - "
-+ "SetPortFeature request %xh "
-+ "unknown or unsupported\n", wValue);
-+ break;
-+ }
-+ break;
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+ case UCR_SET_AND_TEST_PORT_FEATURE:
-+ if (wValue != UHF_PORT_L1) {
-+ goto error;
-+ }
-+ {
-+ int portnum, hird, devaddr, remwake;
-+ glpmcfg_data_t lpmcfg;
-+ uint32_t time_usecs;
-+ gintsts_data_t gintsts;
-+ gintmsk_data_t gintmsk;
-+
-+ if (!dwc_otg_get_param_lpm_enable(core_if)) {
-+ goto error;
-+ }
-+ if (wValue != UHF_PORT_L1 || wLength != 1) {
-+ goto error;
-+ }
-+ /* Check if the port currently is in SLEEP state */
-+ lpmcfg.d32 =
-+ DWC_READ_REG32(&core_if->core_global_regs->glpmcfg);
-+ if (lpmcfg.b.prt_sleep_sts) {
-+ DWC_INFO("Port is already in sleep mode\n");
-+ buf[0] = 0; /* Return success */
-+ break;
-+ }
-+
-+ portnum = wIndex & 0xf;
-+ hird = (wIndex >> 4) & 0xf;
-+ devaddr = (wIndex >> 8) & 0x7f;
-+ remwake = (wIndex >> 15);
-+
-+ if (portnum != 1) {
-+ retval = -DWC_E_INVALID;
-+ DWC_WARN
-+ ("Wrong port number(%d) in SetandTestPortFeature request\n",
-+ portnum);
-+ break;
-+ }
-+
-+ DWC_PRINTF
-+ ("SetandTestPortFeature request: portnum = %d, hird = %d, devaddr = %d, rewake = %d\n",
-+ portnum, hird, devaddr, remwake);
-+ /* Disable LPM interrupt */
-+ gintmsk.d32 = 0;
-+ gintmsk.b.lpmtranrcvd = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gintmsk,
-+ gintmsk.d32, 0);
-+
-+ if (dwc_otg_hcd_send_lpm
-+ (dwc_otg_hcd, devaddr, hird, remwake)) {
-+ retval = -DWC_E_INVALID;
-+ break;
-+ }
-+
-+ time_usecs = 10 * (lpmcfg.b.retry_count + 1);
-+ /* We will consider timeout if time_usecs microseconds pass,
-+ * and we don't receive LPM transaction status.
-+ * After receiving non-error responce(ACK/NYET/STALL) from device,
-+ * core will set lpmtranrcvd bit.
-+ */
-+ do {
-+ gintsts.d32 =
-+ DWC_READ_REG32(&core_if->core_global_regs->gintsts);
-+ if (gintsts.b.lpmtranrcvd) {
-+ break;
-+ }
-+ dwc_udelay(1);
-+ } while (--time_usecs);
-+ /* lpm_int bit will be cleared in LPM interrupt handler */
-+
-+ /* Now fill status
-+ * 0x00 - Success
-+ * 0x10 - NYET
-+ * 0x11 - Timeout
-+ */
-+ if (!gintsts.b.lpmtranrcvd) {
-+ buf[0] = 0x3; /* Completion code is Timeout */
-+ dwc_otg_hcd_free_hc_from_lpm(dwc_otg_hcd);
-+ } else {
-+ lpmcfg.d32 =
-+ DWC_READ_REG32(&core_if->core_global_regs->glpmcfg);
-+ if (lpmcfg.b.lpm_resp == 0x3) {
-+ /* ACK responce from the device */
-+ buf[0] = 0x00; /* Success */
-+ } else if (lpmcfg.b.lpm_resp == 0x2) {
-+ /* NYET responce from the device */
-+ buf[0] = 0x2;
-+ } else {
-+ /* Otherwise responce with Timeout */
-+ buf[0] = 0x3;
-+ }
-+ }
-+ DWC_PRINTF("Device responce to LPM trans is %x\n",
-+ lpmcfg.b.lpm_resp);
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gintmsk, 0,
-+ gintmsk.d32);
-+
-+ break;
-+ }
-+#endif /* CONFIG_USB_DWC_OTG_LPM */
-+ default:
-+error:
-+ retval = -DWC_E_INVALID;
-+ DWC_WARN("DWC OTG HCD - "
-+ "Unknown hub control request type or invalid typeReq: %xh wIndex: %xh wValue: %xh\n",
-+ typeReq, wIndex, wValue);
-+ break;
-+ }
-+
-+ return retval;
-+}
-+
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+/** Returns index of host channel to perform LPM transaction. */
-+int dwc_otg_hcd_get_hc_for_lpm_tran(dwc_otg_hcd_t * hcd, uint8_t devaddr)
-+{
-+ dwc_otg_core_if_t *core_if = hcd->core_if;
-+ dwc_hc_t *hc;
-+ hcchar_data_t hcchar;
-+ gintmsk_data_t gintmsk = {.d32 = 0 };
-+
-+ if (DWC_CIRCLEQ_EMPTY(&hcd->free_hc_list)) {
-+ DWC_PRINTF("No free channel to select for LPM transaction\n");
-+ return -1;
-+ }
-+
-+ hc = DWC_CIRCLEQ_FIRST(&hcd->free_hc_list);
-+
-+ /* Mask host channel interrupts. */
-+ gintmsk.b.hcintr = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gintmsk, gintmsk.d32, 0);
-+
-+ /* Fill fields that core needs for LPM transaction */
-+ hcchar.b.devaddr = devaddr;
-+ hcchar.b.epnum = 0;
-+ hcchar.b.eptype = DWC_OTG_EP_TYPE_CONTROL;
-+ hcchar.b.mps = 64;
-+ hcchar.b.lspddev = (hc->speed == DWC_OTG_EP_SPEED_LOW);
-+ hcchar.b.epdir = 0; /* OUT */
-+ DWC_WRITE_REG32(&core_if->host_if->hc_regs[hc->hc_num]->hcchar,
-+ hcchar.d32);
-+
-+ /* Remove the host channel from the free list. */
-+ DWC_CIRCLEQ_REMOVE_INIT(&hcd->free_hc_list, hc, hc_list_entry);
-+
-+ DWC_PRINTF("hcnum = %d devaddr = %d\n", hc->hc_num, devaddr);
-+
-+ return hc->hc_num;
-+}
-+
-+/** Release hc after performing LPM transaction */
-+void dwc_otg_hcd_free_hc_from_lpm(dwc_otg_hcd_t * hcd)
-+{
-+ dwc_hc_t *hc;
-+ glpmcfg_data_t lpmcfg;
-+ uint8_t hc_num;
-+
-+ lpmcfg.d32 = DWC_READ_REG32(&hcd->core_if->core_global_regs->glpmcfg);
-+ hc_num = lpmcfg.b.lpm_chan_index;
-+
-+ hc = hcd->hc_ptr_array[hc_num];
-+
-+ DWC_PRINTF("Freeing channel %d after LPM\n", hc_num);
-+ /* Return host channel to free list */
-+ DWC_CIRCLEQ_INSERT_TAIL(&hcd->free_hc_list, hc, hc_list_entry);
-+}
-+
-+int dwc_otg_hcd_send_lpm(dwc_otg_hcd_t * hcd, uint8_t devaddr, uint8_t hird,
-+ uint8_t bRemoteWake)
-+{
-+ glpmcfg_data_t lpmcfg;
-+ pcgcctl_data_t pcgcctl = {.d32 = 0 };
-+ int channel;
-+
-+ channel = dwc_otg_hcd_get_hc_for_lpm_tran(hcd, devaddr);
-+ if (channel < 0) {
-+ return channel;
-+ }
-+
-+ pcgcctl.b.enbl_sleep_gating = 1;
-+ DWC_MODIFY_REG32(hcd->core_if->pcgcctl, 0, pcgcctl.d32);
-+
-+ /* Read LPM config register */
-+ lpmcfg.d32 = DWC_READ_REG32(&hcd->core_if->core_global_regs->glpmcfg);
-+
-+ /* Program LPM transaction fields */
-+ lpmcfg.b.rem_wkup_en = bRemoteWake;
-+ lpmcfg.b.hird = hird;
-+ lpmcfg.b.hird_thres = 0x1c;
-+ lpmcfg.b.lpm_chan_index = channel;
-+ lpmcfg.b.en_utmi_sleep = 1;
-+ /* Program LPM config register */
-+ DWC_WRITE_REG32(&hcd->core_if->core_global_regs->glpmcfg, lpmcfg.d32);
-+
-+ /* Send LPM transaction */
-+ lpmcfg.b.send_lpm = 1;
-+ DWC_WRITE_REG32(&hcd->core_if->core_global_regs->glpmcfg, lpmcfg.d32);
-+
-+ return 0;
-+}
-+
-+#endif /* CONFIG_USB_DWC_OTG_LPM */
-+
-+int dwc_otg_hcd_is_status_changed(dwc_otg_hcd_t * hcd, int port)
-+{
-+ int retval;
-+
-+ if (port != 1) {
-+ return -DWC_E_INVALID;
-+ }
-+
-+ retval = (hcd->flags.b.port_connect_status_change ||
-+ hcd->flags.b.port_reset_change ||
-+ hcd->flags.b.port_enable_change ||
-+ hcd->flags.b.port_suspend_change ||
-+ hcd->flags.b.port_over_current_change);
-+#ifdef DEBUG
-+ if (retval) {
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB STATUS DATA:"
-+ " Root port status changed\n");
-+ DWC_DEBUGPL(DBG_HCDV, " port_connect_status_change: %d\n",
-+ hcd->flags.b.port_connect_status_change);
-+ DWC_DEBUGPL(DBG_HCDV, " port_reset_change: %d\n",
-+ hcd->flags.b.port_reset_change);
-+ DWC_DEBUGPL(DBG_HCDV, " port_enable_change: %d\n",
-+ hcd->flags.b.port_enable_change);
-+ DWC_DEBUGPL(DBG_HCDV, " port_suspend_change: %d\n",
-+ hcd->flags.b.port_suspend_change);
-+ DWC_DEBUGPL(DBG_HCDV, " port_over_current_change: %d\n",
-+ hcd->flags.b.port_over_current_change);
-+ }
-+#endif
-+ return retval;
-+}
-+
-+int dwc_otg_hcd_get_frame_number(dwc_otg_hcd_t * dwc_otg_hcd)
-+{
-+ hfnum_data_t hfnum;
-+ hfnum.d32 =
-+ DWC_READ_REG32(&dwc_otg_hcd->core_if->host_if->host_global_regs->
-+ hfnum);
-+
-+#ifdef DEBUG_SOF
-+ DWC_DEBUGPL(DBG_HCDV, "DWC OTG HCD GET FRAME NUMBER %d\n",
-+ hfnum.b.frnum);
-+#endif
-+ return hfnum.b.frnum;
-+}
-+
-+int dwc_otg_hcd_start(dwc_otg_hcd_t * hcd,
-+ struct dwc_otg_hcd_function_ops *fops)
-+{
-+ int retval = 0;
-+
-+ hcd->fops = fops;
-+ if (!dwc_otg_is_device_mode(hcd->core_if) &&
-+ (!hcd->core_if->adp_enable || hcd->core_if->adp.adp_started)) {
-+ dwc_otg_hcd_reinit(hcd);
-+ } else {
-+ retval = -DWC_E_NO_DEVICE;
-+ }
-+
-+ return retval;
-+}
-+
-+void *dwc_otg_hcd_get_priv_data(dwc_otg_hcd_t * hcd)
-+{
-+ return hcd->priv;
-+}
-+
-+void dwc_otg_hcd_set_priv_data(dwc_otg_hcd_t * hcd, void *priv_data)
-+{
-+ hcd->priv = priv_data;
-+}
-+
-+uint32_t dwc_otg_hcd_otg_port(dwc_otg_hcd_t * hcd)
-+{
-+ return hcd->otg_port;
-+}
-+
-+uint32_t dwc_otg_hcd_is_b_host(dwc_otg_hcd_t * hcd)
-+{
-+ uint32_t is_b_host;
-+ if (hcd->core_if->op_state == B_HOST) {
-+ is_b_host = 1;
-+ } else {
-+ is_b_host = 0;
-+ }
-+
-+ return is_b_host;
-+}
-+
-+dwc_otg_hcd_urb_t *dwc_otg_hcd_urb_alloc(dwc_otg_hcd_t * hcd,
-+ int iso_desc_count, int atomic_alloc)
-+{
-+ dwc_otg_hcd_urb_t *dwc_otg_urb;
-+ uint32_t size;
-+
-+ size =
-+ sizeof(*dwc_otg_urb) +
-+ iso_desc_count * sizeof(struct dwc_otg_hcd_iso_packet_desc);
-+ if (atomic_alloc)
-+ dwc_otg_urb = DWC_ALLOC_ATOMIC(size);
-+ else
-+ dwc_otg_urb = DWC_ALLOC(size);
-+
-+ if (dwc_otg_urb)
-+ dwc_otg_urb->packet_count = iso_desc_count;
-+ else {
-+ DWC_ERROR("**** DWC OTG HCD URB alloc - "
-+ "%salloc of %db failed\n",
-+ atomic_alloc?"atomic ":"", size);
-+ }
-+ return dwc_otg_urb;
-+}
-+
-+void dwc_otg_hcd_urb_set_pipeinfo(dwc_otg_hcd_urb_t * dwc_otg_urb,
-+ uint8_t dev_addr, uint8_t ep_num,
-+ uint8_t ep_type, uint8_t ep_dir, uint16_t mps)
-+{
-+ dwc_otg_hcd_fill_pipe(&dwc_otg_urb->pipe_info, dev_addr, ep_num,
-+ ep_type, ep_dir, mps);
-+#if 0
-+ DWC_PRINTF
-+ ("addr = %d, ep_num = %d, ep_dir = 0x%x, ep_type = 0x%x, mps = %d\n",
-+ dev_addr, ep_num, ep_dir, ep_type, mps);
-+#endif
-+}
-+
-+void dwc_otg_hcd_urb_set_params(dwc_otg_hcd_urb_t * dwc_otg_urb,
-+ void *urb_handle, void *buf, dwc_dma_t dma,
-+ uint32_t buflen, void *setup_packet,
-+ dwc_dma_t setup_dma, uint32_t flags,
-+ uint16_t interval)
-+{
-+ dwc_otg_urb->priv = urb_handle;
-+ dwc_otg_urb->buf = buf;
-+ dwc_otg_urb->dma = dma;
-+ dwc_otg_urb->length = buflen;
-+ dwc_otg_urb->setup_packet = setup_packet;
-+ dwc_otg_urb->setup_dma = setup_dma;
-+ dwc_otg_urb->flags = flags;
-+ dwc_otg_urb->interval = interval;
-+ dwc_otg_urb->status = -DWC_E_IN_PROGRESS;
-+}
-+
-+uint32_t dwc_otg_hcd_urb_get_status(dwc_otg_hcd_urb_t * dwc_otg_urb)
-+{
-+ return dwc_otg_urb->status;
-+}
-+
-+uint32_t dwc_otg_hcd_urb_get_actual_length(dwc_otg_hcd_urb_t * dwc_otg_urb)
-+{
-+ return dwc_otg_urb->actual_length;
-+}
-+
-+uint32_t dwc_otg_hcd_urb_get_error_count(dwc_otg_hcd_urb_t * dwc_otg_urb)
-+{
-+ return dwc_otg_urb->error_count;
-+}
-+
-+void dwc_otg_hcd_urb_set_iso_desc_params(dwc_otg_hcd_urb_t * dwc_otg_urb,
-+ int desc_num, uint32_t offset,
-+ uint32_t length)
-+{
-+ dwc_otg_urb->iso_descs[desc_num].offset = offset;
-+ dwc_otg_urb->iso_descs[desc_num].length = length;
-+}
-+
-+uint32_t dwc_otg_hcd_urb_get_iso_desc_status(dwc_otg_hcd_urb_t * dwc_otg_urb,
-+ int desc_num)
-+{
-+ return dwc_otg_urb->iso_descs[desc_num].status;
-+}
-+
-+uint32_t dwc_otg_hcd_urb_get_iso_desc_actual_length(dwc_otg_hcd_urb_t *
-+ dwc_otg_urb, int desc_num)
-+{
-+ return dwc_otg_urb->iso_descs[desc_num].actual_length;
-+}
-+
-+int dwc_otg_hcd_is_bandwidth_allocated(dwc_otg_hcd_t * hcd, void *ep_handle)
-+{
-+ int allocated = 0;
-+ dwc_otg_qh_t *qh = (dwc_otg_qh_t *) ep_handle;
-+
-+ if (qh) {
-+ if (!DWC_LIST_EMPTY(&qh->qh_list_entry)) {
-+ allocated = 1;
-+ }
-+ }
-+ return allocated;
-+}
-+
-+int dwc_otg_hcd_is_bandwidth_freed(dwc_otg_hcd_t * hcd, void *ep_handle)
-+{
-+ dwc_otg_qh_t *qh = (dwc_otg_qh_t *) ep_handle;
-+ int freed = 0;
-+ DWC_ASSERT(qh, "qh is not allocated\n");
-+
-+ if (DWC_LIST_EMPTY(&qh->qh_list_entry)) {
-+ freed = 1;
-+ }
-+
-+ return freed;
-+}
-+
-+uint8_t dwc_otg_hcd_get_ep_bandwidth(dwc_otg_hcd_t * hcd, void *ep_handle)
-+{
-+ dwc_otg_qh_t *qh = (dwc_otg_qh_t *) ep_handle;
-+ DWC_ASSERT(qh, "qh is not allocated\n");
-+ return qh->usecs;
-+}
-+
-+void dwc_otg_hcd_dump_state(dwc_otg_hcd_t * hcd)
-+{
-+#ifdef DEBUG
-+ int num_channels;
-+ int i;
-+ gnptxsts_data_t np_tx_status;
-+ hptxsts_data_t p_tx_status;
-+
-+ num_channels = hcd->core_if->core_params->host_channels;
-+ DWC_PRINTF("\n");
-+ DWC_PRINTF
-+ ("************************************************************\n");
-+ DWC_PRINTF("HCD State:\n");
-+ DWC_PRINTF(" Num channels: %d\n", num_channels);
-+ for (i = 0; i < num_channels; i++) {
-+ dwc_hc_t *hc = hcd->hc_ptr_array[i];
-+ DWC_PRINTF(" Channel %d:\n", i);
-+ DWC_PRINTF(" dev_addr: %d, ep_num: %d, ep_is_in: %d\n",
-+ hc->dev_addr, hc->ep_num, hc->ep_is_in);
-+ DWC_PRINTF(" speed: %d\n", hc->speed);
-+ DWC_PRINTF(" ep_type: %d\n", hc->ep_type);
-+ DWC_PRINTF(" max_packet: %d\n", hc->max_packet);
-+ DWC_PRINTF(" data_pid_start: %d\n", hc->data_pid_start);
-+ DWC_PRINTF(" multi_count: %d\n", hc->multi_count);
-+ DWC_PRINTF(" xfer_started: %d\n", hc->xfer_started);
-+ DWC_PRINTF(" xfer_buff: %p\n", hc->xfer_buff);
-+ DWC_PRINTF(" xfer_len: %d\n", hc->xfer_len);
-+ DWC_PRINTF(" xfer_count: %d\n", hc->xfer_count);
-+ DWC_PRINTF(" halt_on_queue: %d\n", hc->halt_on_queue);
-+ DWC_PRINTF(" halt_pending: %d\n", hc->halt_pending);
-+ DWC_PRINTF(" halt_status: %d\n", hc->halt_status);
-+ DWC_PRINTF(" do_split: %d\n", hc->do_split);
-+ DWC_PRINTF(" complete_split: %d\n", hc->complete_split);
-+ DWC_PRINTF(" hub_addr: %d\n", hc->hub_addr);
-+ DWC_PRINTF(" port_addr: %d\n", hc->port_addr);
-+ DWC_PRINTF(" xact_pos: %d\n", hc->xact_pos);
-+ DWC_PRINTF(" requests: %d\n", hc->requests);
-+ DWC_PRINTF(" qh: %p\n", hc->qh);
-+ if (hc->xfer_started) {
-+ hfnum_data_t hfnum;
-+ hcchar_data_t hcchar;
-+ hctsiz_data_t hctsiz;
-+ hcint_data_t hcint;
-+ hcintmsk_data_t hcintmsk;
-+ hfnum.d32 =
-+ DWC_READ_REG32(&hcd->core_if->
-+ host_if->host_global_regs->hfnum);
-+ hcchar.d32 =
-+ DWC_READ_REG32(&hcd->core_if->host_if->
-+ hc_regs[i]->hcchar);
-+ hctsiz.d32 =
-+ DWC_READ_REG32(&hcd->core_if->host_if->
-+ hc_regs[i]->hctsiz);
-+ hcint.d32 =
-+ DWC_READ_REG32(&hcd->core_if->host_if->
-+ hc_regs[i]->hcint);
-+ hcintmsk.d32 =
-+ DWC_READ_REG32(&hcd->core_if->host_if->
-+ hc_regs[i]->hcintmsk);
-+ DWC_PRINTF(" hfnum: 0x%08x\n", hfnum.d32);
-+ DWC_PRINTF(" hcchar: 0x%08x\n", hcchar.d32);
-+ DWC_PRINTF(" hctsiz: 0x%08x\n", hctsiz.d32);
-+ DWC_PRINTF(" hcint: 0x%08x\n", hcint.d32);
-+ DWC_PRINTF(" hcintmsk: 0x%08x\n", hcintmsk.d32);
-+ }
-+ if (hc->xfer_started && hc->qh) {
-+ dwc_otg_qtd_t *qtd;
-+ dwc_otg_hcd_urb_t *urb;
-+
-+ DWC_CIRCLEQ_FOREACH(qtd, &hc->qh->qtd_list, qtd_list_entry) {
-+ if (!qtd->in_process)
-+ break;
-+
-+ urb = qtd->urb;
-+ DWC_PRINTF(" URB Info:\n");
-+ DWC_PRINTF(" qtd: %p, urb: %p\n", qtd, urb);
-+ if (urb) {
-+ DWC_PRINTF(" Dev: %d, EP: %d %s\n",
-+ dwc_otg_hcd_get_dev_addr(&urb->
-+ pipe_info),
-+ dwc_otg_hcd_get_ep_num(&urb->
-+ pipe_info),
-+ dwc_otg_hcd_is_pipe_in(&urb->
-+ pipe_info) ?
-+ "IN" : "OUT");
-+ DWC_PRINTF(" Max packet size: %d\n",
-+ dwc_otg_hcd_get_mps(&urb->
-+ pipe_info));
-+ DWC_PRINTF(" transfer_buffer: %p\n",
-+ urb->buf);
-+ DWC_PRINTF(" transfer_dma: %p\n",
-+ (void *)urb->dma);
-+ DWC_PRINTF(" transfer_buffer_length: %d\n",
-+ urb->length);
-+ DWC_PRINTF(" actual_length: %d\n",
-+ urb->actual_length);
-+ }
-+ }
-+ }
-+ }
-+ DWC_PRINTF(" non_periodic_channels: %d\n", hcd->non_periodic_channels);
-+ DWC_PRINTF(" periodic_channels: %d\n", hcd->periodic_channels);
-+ DWC_PRINTF(" periodic_usecs: %d\n", hcd->periodic_usecs);
-+ np_tx_status.d32 =
-+ DWC_READ_REG32(&hcd->core_if->core_global_regs->gnptxsts);
-+ DWC_PRINTF(" NP Tx Req Queue Space Avail: %d\n",
-+ np_tx_status.b.nptxqspcavail);
-+ DWC_PRINTF(" NP Tx FIFO Space Avail: %d\n",
-+ np_tx_status.b.nptxfspcavail);
-+ p_tx_status.d32 =
-+ DWC_READ_REG32(&hcd->core_if->host_if->host_global_regs->hptxsts);
-+ DWC_PRINTF(" P Tx Req Queue Space Avail: %d\n",
-+ p_tx_status.b.ptxqspcavail);
-+ DWC_PRINTF(" P Tx FIFO Space Avail: %d\n", p_tx_status.b.ptxfspcavail);
-+ dwc_otg_hcd_dump_frrem(hcd);
-+ dwc_otg_dump_global_registers(hcd->core_if);
-+ dwc_otg_dump_host_registers(hcd->core_if);
-+ DWC_PRINTF
-+ ("************************************************************\n");
-+ DWC_PRINTF("\n");
-+#endif
-+}
-+
-+#ifdef DEBUG
-+void dwc_print_setup_data(uint8_t * setup)
-+{
-+ int i;
-+ if (CHK_DEBUG_LEVEL(DBG_HCD)) {
-+ DWC_PRINTF("Setup Data = MSB ");
-+ for (i = 7; i >= 0; i--)
-+ DWC_PRINTF("%02x ", setup[i]);
-+ DWC_PRINTF("\n");
-+ DWC_PRINTF(" bmRequestType Tranfer = %s\n",
-+ (setup[0] & 0x80) ? "Device-to-Host" :
-+ "Host-to-Device");
-+ DWC_PRINTF(" bmRequestType Type = ");
-+ switch ((setup[0] & 0x60) >> 5) {
-+ case 0:
-+ DWC_PRINTF("Standard\n");
-+ break;
-+ case 1:
-+ DWC_PRINTF("Class\n");
-+ break;
-+ case 2:
-+ DWC_PRINTF("Vendor\n");
-+ break;
-+ case 3:
-+ DWC_PRINTF("Reserved\n");
-+ break;
-+ }
-+ DWC_PRINTF(" bmRequestType Recipient = ");
-+ switch (setup[0] & 0x1f) {
-+ case 0:
-+ DWC_PRINTF("Device\n");
-+ break;
-+ case 1:
-+ DWC_PRINTF("Interface\n");
-+ break;
-+ case 2:
-+ DWC_PRINTF("Endpoint\n");
-+ break;
-+ case 3:
-+ DWC_PRINTF("Other\n");
-+ break;
-+ default:
-+ DWC_PRINTF("Reserved\n");
-+ break;
-+ }
-+ DWC_PRINTF(" bRequest = 0x%0x\n", setup[1]);
-+ DWC_PRINTF(" wValue = 0x%0x\n", *((uint16_t *) & setup[2]));
-+ DWC_PRINTF(" wIndex = 0x%0x\n", *((uint16_t *) & setup[4]));
-+ DWC_PRINTF(" wLength = 0x%0x\n\n", *((uint16_t *) & setup[6]));
-+ }
-+}
-+#endif
-+
-+void dwc_otg_hcd_dump_frrem(dwc_otg_hcd_t * hcd)
-+{
-+#if 0
-+ DWC_PRINTF("Frame remaining at SOF:\n");
-+ DWC_PRINTF(" samples %u, accum %llu, avg %llu\n",
-+ hcd->frrem_samples, hcd->frrem_accum,
-+ (hcd->frrem_samples > 0) ?
-+ hcd->frrem_accum / hcd->frrem_samples : 0);
-+
-+ DWC_PRINTF("\n");
-+ DWC_PRINTF("Frame remaining at start_transfer (uframe 7):\n");
-+ DWC_PRINTF(" samples %u, accum %llu, avg %llu\n",
-+ hcd->core_if->hfnum_7_samples,
-+ hcd->core_if->hfnum_7_frrem_accum,
-+ (hcd->core_if->hfnum_7_samples >
-+ 0) ? hcd->core_if->hfnum_7_frrem_accum /
-+ hcd->core_if->hfnum_7_samples : 0);
-+ DWC_PRINTF("Frame remaining at start_transfer (uframe 0):\n");
-+ DWC_PRINTF(" samples %u, accum %llu, avg %llu\n",
-+ hcd->core_if->hfnum_0_samples,
-+ hcd->core_if->hfnum_0_frrem_accum,
-+ (hcd->core_if->hfnum_0_samples >
-+ 0) ? hcd->core_if->hfnum_0_frrem_accum /
-+ hcd->core_if->hfnum_0_samples : 0);
-+ DWC_PRINTF("Frame remaining at start_transfer (uframe 1-6):\n");
-+ DWC_PRINTF(" samples %u, accum %llu, avg %llu\n",
-+ hcd->core_if->hfnum_other_samples,
-+ hcd->core_if->hfnum_other_frrem_accum,
-+ (hcd->core_if->hfnum_other_samples >
-+ 0) ? hcd->core_if->hfnum_other_frrem_accum /
-+ hcd->core_if->hfnum_other_samples : 0);
-+
-+ DWC_PRINTF("\n");
-+ DWC_PRINTF("Frame remaining at sample point A (uframe 7):\n");
-+ DWC_PRINTF(" samples %u, accum %llu, avg %llu\n",
-+ hcd->hfnum_7_samples_a, hcd->hfnum_7_frrem_accum_a,
-+ (hcd->hfnum_7_samples_a > 0) ?
-+ hcd->hfnum_7_frrem_accum_a / hcd->hfnum_7_samples_a : 0);
-+ DWC_PRINTF("Frame remaining at sample point A (uframe 0):\n");
-+ DWC_PRINTF(" samples %u, accum %llu, avg %llu\n",
-+ hcd->hfnum_0_samples_a, hcd->hfnum_0_frrem_accum_a,
-+ (hcd->hfnum_0_samples_a > 0) ?
-+ hcd->hfnum_0_frrem_accum_a / hcd->hfnum_0_samples_a : 0);
-+ DWC_PRINTF("Frame remaining at sample point A (uframe 1-6):\n");
-+ DWC_PRINTF(" samples %u, accum %llu, avg %llu\n",
-+ hcd->hfnum_other_samples_a, hcd->hfnum_other_frrem_accum_a,
-+ (hcd->hfnum_other_samples_a > 0) ?
-+ hcd->hfnum_other_frrem_accum_a /
-+ hcd->hfnum_other_samples_a : 0);
-+
-+ DWC_PRINTF("\n");
-+ DWC_PRINTF("Frame remaining at sample point B (uframe 7):\n");
-+ DWC_PRINTF(" samples %u, accum %llu, avg %llu\n",
-+ hcd->hfnum_7_samples_b, hcd->hfnum_7_frrem_accum_b,
-+ (hcd->hfnum_7_samples_b > 0) ?
-+ hcd->hfnum_7_frrem_accum_b / hcd->hfnum_7_samples_b : 0);
-+ DWC_PRINTF("Frame remaining at sample point B (uframe 0):\n");
-+ DWC_PRINTF(" samples %u, accum %llu, avg %llu\n",
-+ hcd->hfnum_0_samples_b, hcd->hfnum_0_frrem_accum_b,
-+ (hcd->hfnum_0_samples_b > 0) ?
-+ hcd->hfnum_0_frrem_accum_b / hcd->hfnum_0_samples_b : 0);
-+ DWC_PRINTF("Frame remaining at sample point B (uframe 1-6):\n");
-+ DWC_PRINTF(" samples %u, accum %llu, avg %llu\n",
-+ hcd->hfnum_other_samples_b, hcd->hfnum_other_frrem_accum_b,
-+ (hcd->hfnum_other_samples_b > 0) ?
-+ hcd->hfnum_other_frrem_accum_b /
-+ hcd->hfnum_other_samples_b : 0);
-+#endif
-+}
-+
-+#endif /* DWC_DEVICE_ONLY */
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_hcd.h
-@@ -0,0 +1,862 @@
-+/* ==========================================================================
-+ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_hcd.h $
-+ * $Revision: #58 $
-+ * $Date: 2011/09/15 $
-+ * $Change: 1846647 $
-+ *
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+#ifndef DWC_DEVICE_ONLY
-+#ifndef __DWC_HCD_H__
-+#define __DWC_HCD_H__
-+
-+#include "dwc_otg_os_dep.h"
-+#include "usb.h"
-+#include "dwc_otg_hcd_if.h"
-+#include "dwc_otg_core_if.h"
-+#include "dwc_list.h"
-+#include "dwc_otg_cil.h"
-+#include "dwc_otg_fiq_fsm.h"
-+
-+
-+/**
-+ * @file
-+ *
-+ * This file contains the structures, constants, and interfaces for
-+ * the Host Contoller Driver (HCD).
-+ *
-+ * The Host Controller Driver (HCD) is responsible for translating requests
-+ * from the USB Driver into the appropriate actions on the DWC_otg controller.
-+ * It isolates the USBD from the specifics of the controller by providing an
-+ * API to the USBD.
-+ */
-+
-+struct dwc_otg_hcd_pipe_info {
-+ uint8_t dev_addr;
-+ uint8_t ep_num;
-+ uint8_t pipe_type;
-+ uint8_t pipe_dir;
-+ uint16_t mps;
-+};
-+
-+struct dwc_otg_hcd_iso_packet_desc {
-+ uint32_t offset;
-+ uint32_t length;
-+ uint32_t actual_length;
-+ uint32_t status;
-+};
-+
-+struct dwc_otg_qtd;
-+
-+struct dwc_otg_hcd_urb {
-+ void *priv;
-+ struct dwc_otg_qtd *qtd;
-+ void *buf;
-+ dwc_dma_t dma;
-+ void *setup_packet;
-+ dwc_dma_t setup_dma;
-+ uint32_t length;
-+ uint32_t actual_length;
-+ uint32_t status;
-+ uint32_t error_count;
-+ uint32_t packet_count;
-+ uint32_t flags;
-+ uint16_t interval;
-+ struct dwc_otg_hcd_pipe_info pipe_info;
-+ struct dwc_otg_hcd_iso_packet_desc iso_descs[0];
-+};
-+
-+static inline uint8_t dwc_otg_hcd_get_ep_num(struct dwc_otg_hcd_pipe_info *pipe)
-+{
-+ return pipe->ep_num;
-+}
-+
-+static inline uint8_t dwc_otg_hcd_get_pipe_type(struct dwc_otg_hcd_pipe_info
-+ *pipe)
-+{
-+ return pipe->pipe_type;
-+}
-+
-+static inline uint16_t dwc_otg_hcd_get_mps(struct dwc_otg_hcd_pipe_info *pipe)
-+{
-+ return pipe->mps;
-+}
-+
-+static inline uint8_t dwc_otg_hcd_get_dev_addr(struct dwc_otg_hcd_pipe_info
-+ *pipe)
-+{
-+ return pipe->dev_addr;
-+}
-+
-+static inline uint8_t dwc_otg_hcd_is_pipe_isoc(struct dwc_otg_hcd_pipe_info
-+ *pipe)
-+{
-+ return (pipe->pipe_type == UE_ISOCHRONOUS);
-+}
-+
-+static inline uint8_t dwc_otg_hcd_is_pipe_int(struct dwc_otg_hcd_pipe_info
-+ *pipe)
-+{
-+ return (pipe->pipe_type == UE_INTERRUPT);
-+}
-+
-+static inline uint8_t dwc_otg_hcd_is_pipe_bulk(struct dwc_otg_hcd_pipe_info
-+ *pipe)
-+{
-+ return (pipe->pipe_type == UE_BULK);
-+}
-+
-+static inline uint8_t dwc_otg_hcd_is_pipe_control(struct dwc_otg_hcd_pipe_info
-+ *pipe)
-+{
-+ return (pipe->pipe_type == UE_CONTROL);
-+}
-+
-+static inline uint8_t dwc_otg_hcd_is_pipe_in(struct dwc_otg_hcd_pipe_info *pipe)
-+{
-+ return (pipe->pipe_dir == UE_DIR_IN);
-+}
-+
-+static inline uint8_t dwc_otg_hcd_is_pipe_out(struct dwc_otg_hcd_pipe_info
-+ *pipe)
-+{
-+ return (!dwc_otg_hcd_is_pipe_in(pipe));
-+}
-+
-+static inline void dwc_otg_hcd_fill_pipe(struct dwc_otg_hcd_pipe_info *pipe,
-+ uint8_t devaddr, uint8_t ep_num,
-+ uint8_t pipe_type, uint8_t pipe_dir,
-+ uint16_t mps)
-+{
-+ pipe->dev_addr = devaddr;
-+ pipe->ep_num = ep_num;
-+ pipe->pipe_type = pipe_type;
-+ pipe->pipe_dir = pipe_dir;
-+ pipe->mps = mps;
-+}
-+
-+/**
-+ * Phases for control transfers.
-+ */
-+typedef enum dwc_otg_control_phase {
-+ DWC_OTG_CONTROL_SETUP,
-+ DWC_OTG_CONTROL_DATA,
-+ DWC_OTG_CONTROL_STATUS
-+} dwc_otg_control_phase_e;
-+
-+/** Transaction types. */
-+typedef enum dwc_otg_transaction_type {
-+ DWC_OTG_TRANSACTION_NONE = 0,
-+ DWC_OTG_TRANSACTION_PERIODIC = 1,
-+ DWC_OTG_TRANSACTION_NON_PERIODIC = 2,
-+ DWC_OTG_TRANSACTION_ALL = DWC_OTG_TRANSACTION_PERIODIC + DWC_OTG_TRANSACTION_NON_PERIODIC
-+} dwc_otg_transaction_type_e;
-+
-+struct dwc_otg_qh;
-+
-+/**
-+ * A Queue Transfer Descriptor (QTD) holds the state of a bulk, control,
-+ * interrupt, or isochronous transfer. A single QTD is created for each URB
-+ * (of one of these types) submitted to the HCD. The transfer associated with
-+ * a QTD may require one or multiple transactions.
-+ *
-+ * A QTD is linked to a Queue Head, which is entered in either the
-+ * non-periodic or periodic schedule for execution. When a QTD is chosen for
-+ * execution, some or all of its transactions may be executed. After
-+ * execution, the state of the QTD is updated. The QTD may be retired if all
-+ * its transactions are complete or if an error occurred. Otherwise, it
-+ * remains in the schedule so more transactions can be executed later.
-+ */
-+typedef struct dwc_otg_qtd {
-+ /**
-+ * Determines the PID of the next data packet for the data phase of
-+ * control transfers. Ignored for other transfer types.<br>
-+ * One of the following values:
-+ * - DWC_OTG_HC_PID_DATA0
-+ * - DWC_OTG_HC_PID_DATA1
-+ */
-+ uint8_t data_toggle;
-+
-+ /** Current phase for control transfers (Setup, Data, or Status). */
-+ dwc_otg_control_phase_e control_phase;
-+
-+ /** Keep track of the current split type
-+ * for FS/LS endpoints on a HS Hub */
-+ uint8_t complete_split;
-+
-+ /** How many bytes transferred during SSPLIT OUT */
-+ uint32_t ssplit_out_xfer_count;
-+
-+ /**
-+ * Holds the number of bus errors that have occurred for a transaction
-+ * within this transfer.
-+ */
-+ uint8_t error_count;
-+
-+ /**
-+ * Index of the next frame descriptor for an isochronous transfer. A
-+ * frame descriptor describes the buffer position and length of the
-+ * data to be transferred in the next scheduled (micro)frame of an
-+ * isochronous transfer. It also holds status for that transaction.
-+ * The frame index starts at 0.
-+ */
-+ uint16_t isoc_frame_index;
-+
-+ /** Position of the ISOC split on full/low speed */
-+ uint8_t isoc_split_pos;
-+
-+ /** Position of the ISOC split in the buffer for the current frame */
-+ uint16_t isoc_split_offset;
-+
-+ /** URB for this transfer */
-+ struct dwc_otg_hcd_urb *urb;
-+
-+ struct dwc_otg_qh *qh;
-+
-+ /** This list of QTDs */
-+ DWC_CIRCLEQ_ENTRY(dwc_otg_qtd) qtd_list_entry;
-+
-+ /** Indicates if this QTD is currently processed by HW. */
-+ uint8_t in_process;
-+
-+ /** Number of DMA descriptors for this QTD */
-+ uint8_t n_desc;
-+
-+ /**
-+ * Last activated frame(packet) index.
-+ * Used in Descriptor DMA mode only.
-+ */
-+ uint16_t isoc_frame_index_last;
-+
-+} dwc_otg_qtd_t;
-+
-+DWC_CIRCLEQ_HEAD(dwc_otg_qtd_list, dwc_otg_qtd);
-+
-+/**
-+ * A Queue Head (QH) holds the static characteristics of an endpoint and
-+ * maintains a list of transfers (QTDs) for that endpoint. A QH structure may
-+ * be entered in either the non-periodic or periodic schedule.
-+ */
-+typedef struct dwc_otg_qh {
-+ /**
-+ * Endpoint type.
-+ * One of the following values:
-+ * - UE_CONTROL
-+ * - UE_BULK
-+ * - UE_INTERRUPT
-+ * - UE_ISOCHRONOUS
-+ */
-+ uint8_t ep_type;
-+ uint8_t ep_is_in;
-+
-+ /** wMaxPacketSize Field of Endpoint Descriptor. */
-+ uint16_t maxp;
-+
-+ /**
-+ * Device speed.
-+ * One of the following values:
-+ * - DWC_OTG_EP_SPEED_LOW
-+ * - DWC_OTG_EP_SPEED_FULL
-+ * - DWC_OTG_EP_SPEED_HIGH
-+ */
-+ uint8_t dev_speed;
-+
-+ /**
-+ * Determines the PID of the next data packet for non-control
-+ * transfers. Ignored for control transfers.<br>
-+ * One of the following values:
-+ * - DWC_OTG_HC_PID_DATA0
-+ * - DWC_OTG_HC_PID_DATA1
-+ */
-+ uint8_t data_toggle;
-+
-+ /** Ping state if 1. */
-+ uint8_t ping_state;
-+
-+ /**
-+ * List of QTDs for this QH.
-+ */
-+ struct dwc_otg_qtd_list qtd_list;
-+
-+ /** Host channel currently processing transfers for this QH. */
-+ struct dwc_hc *channel;
-+
-+ /** Full/low speed endpoint on high-speed hub requires split. */
-+ uint8_t do_split;
-+
-+ /** @name Periodic schedule information */
-+ /** @{ */
-+
-+ /** Bandwidth in microseconds per (micro)frame. */
-+ uint16_t usecs;
-+
-+ /** Interval between transfers in (micro)frames. */
-+ uint16_t interval;
-+
-+ /**
-+ * (micro)frame to initialize a periodic transfer. The transfer
-+ * executes in the following (micro)frame.
-+ */
-+ uint16_t sched_frame;
-+
-+ /*
-+ ** Frame a NAK was received on this queue head, used to minimise NAK retransmission
-+ */
-+ uint16_t nak_frame;
-+
-+ /** (micro)frame at which last start split was initialized. */
-+ uint16_t start_split_frame;
-+
-+ /** @} */
-+
-+ /**
-+ * Used instead of original buffer if
-+ * it(physical address) is not dword-aligned.
-+ */
-+ uint8_t *dw_align_buf;
-+ dwc_dma_t dw_align_buf_dma;
-+
-+ /** Entry for QH in either the periodic or non-periodic schedule. */
-+ dwc_list_link_t qh_list_entry;
-+
-+ /** @name Descriptor DMA support */
-+ /** @{ */
-+
-+ /** Descriptor List. */
-+ dwc_otg_host_dma_desc_t *desc_list;
-+
-+ /** Descriptor List physical address. */
-+ dwc_dma_t desc_list_dma;
-+
-+ /**
-+ * Xfer Bytes array.
-+ * Each element corresponds to a descriptor and indicates
-+ * original XferSize size value for the descriptor.
-+ */
-+ uint32_t *n_bytes;
-+
-+ /** Actual number of transfer descriptors in a list. */
-+ uint16_t ntd;
-+
-+ /** First activated isochronous transfer descriptor index. */
-+ uint8_t td_first;
-+ /** Last activated isochronous transfer descriptor index. */
-+ uint8_t td_last;
-+
-+ /** @} */
-+
-+
-+ uint16_t speed;
-+ uint16_t frame_usecs[8];
-+
-+ uint32_t skip_count;
-+} dwc_otg_qh_t;
-+
-+DWC_CIRCLEQ_HEAD(hc_list, dwc_hc);
-+
-+typedef struct urb_tq_entry {
-+ struct urb *urb;
-+ DWC_TAILQ_ENTRY(urb_tq_entry) urb_tq_entries;
-+} urb_tq_entry_t;
-+
-+DWC_TAILQ_HEAD(urb_list, urb_tq_entry);
-+
-+/**
-+ * This structure holds the state of the HCD, including the non-periodic and
-+ * periodic schedules.
-+ */
-+struct dwc_otg_hcd {
-+ /** The DWC otg device pointer */
-+ struct dwc_otg_device *otg_dev;
-+ /** DWC OTG Core Interface Layer */
-+ dwc_otg_core_if_t *core_if;
-+
-+ /** Function HCD driver callbacks */
-+ struct dwc_otg_hcd_function_ops *fops;
-+
-+ /** Internal DWC HCD Flags */
-+ volatile union dwc_otg_hcd_internal_flags {
-+ uint32_t d32;
-+ struct {
-+ unsigned port_connect_status_change:1;
-+ unsigned port_connect_status:1;
-+ unsigned port_reset_change:1;
-+ unsigned port_enable_change:1;
-+ unsigned port_suspend_change:1;
-+ unsigned port_over_current_change:1;
-+ unsigned port_l1_change:1;
-+ unsigned reserved:26;
-+ } b;
-+ } flags;
-+
-+ /**
-+ * Inactive items in the non-periodic schedule. This is a list of
-+ * Queue Heads. Transfers associated with these Queue Heads are not
-+ * currently assigned to a host channel.
-+ */
-+ dwc_list_link_t non_periodic_sched_inactive;
-+
-+ /**
-+ * Active items in the non-periodic schedule. This is a list of
-+ * Queue Heads. Transfers associated with these Queue Heads are
-+ * currently assigned to a host channel.
-+ */
-+ dwc_list_link_t non_periodic_sched_active;
-+
-+ /**
-+ * Pointer to the next Queue Head to process in the active
-+ * non-periodic schedule.
-+ */
-+ dwc_list_link_t *non_periodic_qh_ptr;
-+
-+ /**
-+ * Inactive items in the periodic schedule. This is a list of QHs for
-+ * periodic transfers that are _not_ scheduled for the next frame.
-+ * Each QH in the list has an interval counter that determines when it
-+ * needs to be scheduled for execution. This scheduling mechanism
-+ * allows only a simple calculation for periodic bandwidth used (i.e.
-+ * must assume that all periodic transfers may need to execute in the
-+ * same frame). However, it greatly simplifies scheduling and should
-+ * be sufficient for the vast majority of OTG hosts, which need to
-+ * connect to a small number of peripherals at one time.
-+ *
-+ * Items move from this list to periodic_sched_ready when the QH
-+ * interval counter is 0 at SOF.
-+ */
-+ dwc_list_link_t periodic_sched_inactive;
-+
-+ /**
-+ * List of periodic QHs that are ready for execution in the next
-+ * frame, but have not yet been assigned to host channels.
-+ *
-+ * Items move from this list to periodic_sched_assigned as host
-+ * channels become available during the current frame.
-+ */
-+ dwc_list_link_t periodic_sched_ready;
-+
-+ /**
-+ * List of periodic QHs to be executed in the next frame that are
-+ * assigned to host channels.
-+ *
-+ * Items move from this list to periodic_sched_queued as the
-+ * transactions for the QH are queued to the DWC_otg controller.
-+ */
-+ dwc_list_link_t periodic_sched_assigned;
-+
-+ /**
-+ * List of periodic QHs that have been queued for execution.
-+ *
-+ * Items move from this list to either periodic_sched_inactive or
-+ * periodic_sched_ready when the channel associated with the transfer
-+ * is released. If the interval for the QH is 1, the item moves to
-+ * periodic_sched_ready because it must be rescheduled for the next
-+ * frame. Otherwise, the item moves to periodic_sched_inactive.
-+ */
-+ dwc_list_link_t periodic_sched_queued;
-+
-+ /**
-+ * Total bandwidth claimed so far for periodic transfers. This value
-+ * is in microseconds per (micro)frame. The assumption is that all
-+ * periodic transfers may occur in the same (micro)frame.
-+ */
-+ uint16_t periodic_usecs;
-+
-+ /**
-+ * Total bandwidth claimed so far for all periodic transfers
-+ * in a frame.
-+ * This will include a mixture of HS and FS transfers.
-+ * Units are microseconds per (micro)frame.
-+ * We have a budget per frame and have to schedule
-+ * transactions accordingly.
-+ * Watch out for the fact that things are actually scheduled for the
-+ * "next frame".
-+ */
-+ uint16_t frame_usecs[8];
-+
-+
-+ /**
-+ * Frame number read from the core at SOF. The value ranges from 0 to
-+ * DWC_HFNUM_MAX_FRNUM.
-+ */
-+ uint16_t frame_number;
-+
-+ /**
-+ * Count of periodic QHs, if using several eps. For SOF enable/disable.
-+ */
-+ uint16_t periodic_qh_count;
-+
-+ /**
-+ * Free host channels in the controller. This is a list of
-+ * dwc_hc_t items.
-+ */
-+ struct hc_list free_hc_list;
-+ /**
-+ * Number of host channels assigned to periodic transfers. Currently
-+ * assuming that there is a dedicated host channel for each periodic
-+ * transaction and at least one host channel available for
-+ * non-periodic transactions.
-+ */
-+ int periodic_channels; /* microframe_schedule==0 */
-+
-+ /**
-+ * Number of host channels assigned to non-periodic transfers.
-+ */
-+ int non_periodic_channels; /* microframe_schedule==0 */
-+
-+ /**
-+ * Number of host channels assigned to non-periodic transfers.
-+ */
-+ int available_host_channels;
-+
-+ /**
-+ * Array of pointers to the host channel descriptors. Allows accessing
-+ * a host channel descriptor given the host channel number. This is
-+ * useful in interrupt handlers.
-+ */
-+ struct dwc_hc *hc_ptr_array[MAX_EPS_CHANNELS];
-+
-+ /**
-+ * Buffer to use for any data received during the status phase of a
-+ * control transfer. Normally no data is transferred during the status
-+ * phase. This buffer is used as a bit bucket.
-+ */
-+ uint8_t *status_buf;
-+
-+ /**
-+ * DMA address for status_buf.
-+ */
-+ dma_addr_t status_buf_dma;
-+#define DWC_OTG_HCD_STATUS_BUF_SIZE 64
-+
-+ /**
-+ * Connection timer. An OTG host must display a message if the device
-+ * does not connect. Started when the VBus power is turned on via
-+ * sysfs attribute "buspower".
-+ */
-+ dwc_timer_t *conn_timer;
-+
-+ /* Tasket to do a reset */
-+ dwc_tasklet_t *reset_tasklet;
-+
-+ dwc_tasklet_t *completion_tasklet;
-+ struct urb_list completed_urb_list;
-+
-+ /* */
-+ dwc_spinlock_t *lock;
-+ dwc_spinlock_t *channel_lock;
-+ /**
-+ * Private data that could be used by OS wrapper.
-+ */
-+ void *priv;
-+
-+ uint8_t otg_port;
-+
-+ /** Frame List */
-+ uint32_t *frame_list;
-+
-+ /** Hub - Port assignment */
-+ int hub_port[128];
-+#ifdef FIQ_DEBUG
-+ int hub_port_alloc[2048];
-+#endif
-+
-+ /** Frame List DMA address */
-+ dma_addr_t frame_list_dma;
-+
-+ struct fiq_stack *fiq_stack;
-+ struct fiq_state *fiq_state;
-+
-+ /** Virtual address for split transaction DMA bounce buffers */
-+ struct fiq_dma_blob *fiq_dmab;
-+
-+#ifdef DEBUG
-+ uint32_t frrem_samples;
-+ uint64_t frrem_accum;
-+
-+ uint32_t hfnum_7_samples_a;
-+ uint64_t hfnum_7_frrem_accum_a;
-+ uint32_t hfnum_0_samples_a;
-+ uint64_t hfnum_0_frrem_accum_a;
-+ uint32_t hfnum_other_samples_a;
-+ uint64_t hfnum_other_frrem_accum_a;
-+
-+ uint32_t hfnum_7_samples_b;
-+ uint64_t hfnum_7_frrem_accum_b;
-+ uint32_t hfnum_0_samples_b;
-+ uint64_t hfnum_0_frrem_accum_b;
-+ uint32_t hfnum_other_samples_b;
-+ uint64_t hfnum_other_frrem_accum_b;
-+#endif
-+};
-+
-+/** @name Transaction Execution Functions */
-+/** @{ */
-+extern dwc_otg_transaction_type_e dwc_otg_hcd_select_transactions(dwc_otg_hcd_t
-+ * hcd);
-+extern void dwc_otg_hcd_queue_transactions(dwc_otg_hcd_t * hcd,
-+ dwc_otg_transaction_type_e tr_type);
-+
-+int dwc_otg_hcd_allocate_port(dwc_otg_hcd_t * hcd, dwc_otg_qh_t *qh);
-+void dwc_otg_hcd_release_port(dwc_otg_hcd_t * dwc_otg_hcd, dwc_otg_qh_t *qh);
-+
-+extern int fiq_fsm_queue_transaction(dwc_otg_hcd_t *hcd, dwc_otg_qh_t *qh);
-+extern int fiq_fsm_transaction_suitable(dwc_otg_qh_t *qh);
-+extern void dwc_otg_cleanup_fiq_channel(dwc_otg_hcd_t *hcd, uint32_t num);
-+
-+/** @} */
-+
-+/** @name Interrupt Handler Functions */
-+/** @{ */
-+extern int32_t dwc_otg_hcd_handle_intr(dwc_otg_hcd_t * dwc_otg_hcd);
-+extern int32_t dwc_otg_hcd_handle_sof_intr(dwc_otg_hcd_t * dwc_otg_hcd);
-+extern int32_t dwc_otg_hcd_handle_rx_status_q_level_intr(dwc_otg_hcd_t *
-+ dwc_otg_hcd);
-+extern int32_t dwc_otg_hcd_handle_np_tx_fifo_empty_intr(dwc_otg_hcd_t *
-+ dwc_otg_hcd);
-+extern int32_t dwc_otg_hcd_handle_perio_tx_fifo_empty_intr(dwc_otg_hcd_t *
-+ dwc_otg_hcd);
-+extern int32_t dwc_otg_hcd_handle_incomplete_periodic_intr(dwc_otg_hcd_t *
-+ dwc_otg_hcd);
-+extern int32_t dwc_otg_hcd_handle_port_intr(dwc_otg_hcd_t * dwc_otg_hcd);
-+extern int32_t dwc_otg_hcd_handle_conn_id_status_change_intr(dwc_otg_hcd_t *
-+ dwc_otg_hcd);
-+extern int32_t dwc_otg_hcd_handle_disconnect_intr(dwc_otg_hcd_t * dwc_otg_hcd);
-+extern int32_t dwc_otg_hcd_handle_hc_intr(dwc_otg_hcd_t * dwc_otg_hcd);
-+extern int32_t dwc_otg_hcd_handle_hc_n_intr(dwc_otg_hcd_t * dwc_otg_hcd,
-+ uint32_t num);
-+extern int32_t dwc_otg_hcd_handle_session_req_intr(dwc_otg_hcd_t * dwc_otg_hcd);
-+extern int32_t dwc_otg_hcd_handle_wakeup_detected_intr(dwc_otg_hcd_t *
-+ dwc_otg_hcd);
-+/** @} */
-+
-+/** @name Schedule Queue Functions */
-+/** @{ */
-+
-+/* Implemented in dwc_otg_hcd_queue.c */
-+extern dwc_otg_qh_t *dwc_otg_hcd_qh_create(dwc_otg_hcd_t * hcd,
-+ dwc_otg_hcd_urb_t * urb, int atomic_alloc);
-+extern void dwc_otg_hcd_qh_free(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh);
-+extern int dwc_otg_hcd_qh_add(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh);
-+extern void dwc_otg_hcd_qh_remove(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh);
-+extern void dwc_otg_hcd_qh_deactivate(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh,
-+ int sched_csplit);
-+
-+/** Remove and free a QH */
-+static inline void dwc_otg_hcd_qh_remove_and_free(dwc_otg_hcd_t * hcd,
-+ dwc_otg_qh_t * qh)
-+{
-+ dwc_irqflags_t flags;
-+ DWC_SPINLOCK_IRQSAVE(hcd->lock, &flags);
-+ dwc_otg_hcd_qh_remove(hcd, qh);
-+ DWC_SPINUNLOCK_IRQRESTORE(hcd->lock, flags);
-+ dwc_otg_hcd_qh_free(hcd, qh);
-+}
-+
-+/** Allocates memory for a QH structure.
-+ * @return Returns the memory allocate or NULL on error. */
-+static inline dwc_otg_qh_t *dwc_otg_hcd_qh_alloc(int atomic_alloc)
-+{
-+ if (atomic_alloc)
-+ return (dwc_otg_qh_t *) DWC_ALLOC_ATOMIC(sizeof(dwc_otg_qh_t));
-+ else
-+ return (dwc_otg_qh_t *) DWC_ALLOC(sizeof(dwc_otg_qh_t));
-+}
-+
-+extern dwc_otg_qtd_t *dwc_otg_hcd_qtd_create(dwc_otg_hcd_urb_t * urb,
-+ int atomic_alloc);
-+extern void dwc_otg_hcd_qtd_init(dwc_otg_qtd_t * qtd, dwc_otg_hcd_urb_t * urb);
-+extern int dwc_otg_hcd_qtd_add(dwc_otg_qtd_t * qtd, dwc_otg_hcd_t * dwc_otg_hcd,
-+ dwc_otg_qh_t ** qh, int atomic_alloc);
-+
-+/** Allocates memory for a QTD structure.
-+ * @return Returns the memory allocate or NULL on error. */
-+static inline dwc_otg_qtd_t *dwc_otg_hcd_qtd_alloc(int atomic_alloc)
-+{
-+ if (atomic_alloc)
-+ return (dwc_otg_qtd_t *) DWC_ALLOC_ATOMIC(sizeof(dwc_otg_qtd_t));
-+ else
-+ return (dwc_otg_qtd_t *) DWC_ALLOC(sizeof(dwc_otg_qtd_t));
-+}
-+
-+/** Frees the memory for a QTD structure. QTD should already be removed from
-+ * list.
-+ * @param qtd QTD to free.*/
-+static inline void dwc_otg_hcd_qtd_free(dwc_otg_qtd_t * qtd)
-+{
-+ DWC_FREE(qtd);
-+}
-+
-+/** Removes a QTD from list.
-+ * @param hcd HCD instance.
-+ * @param qtd QTD to remove from list.
-+ * @param qh QTD belongs to.
-+ */
-+static inline void dwc_otg_hcd_qtd_remove(dwc_otg_hcd_t * hcd,
-+ dwc_otg_qtd_t * qtd,
-+ dwc_otg_qh_t * qh)
-+{
-+ DWC_CIRCLEQ_REMOVE(&qh->qtd_list, qtd, qtd_list_entry);
-+}
-+
-+/** Remove and free a QTD
-+ * Need to disable IRQ and hold hcd lock while calling this function out of
-+ * interrupt servicing chain */
-+static inline void dwc_otg_hcd_qtd_remove_and_free(dwc_otg_hcd_t * hcd,
-+ dwc_otg_qtd_t * qtd,
-+ dwc_otg_qh_t * qh)
-+{
-+ dwc_otg_hcd_qtd_remove(hcd, qtd, qh);
-+ dwc_otg_hcd_qtd_free(qtd);
-+}
-+
-+/** @} */
-+
-+/** @name Descriptor DMA Supporting Functions */
-+/** @{ */
-+
-+extern void dwc_otg_hcd_start_xfer_ddma(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh);
-+extern void dwc_otg_hcd_complete_xfer_ddma(dwc_otg_hcd_t * hcd,
-+ dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs,
-+ dwc_otg_halt_status_e halt_status);
-+
-+extern int dwc_otg_hcd_qh_init_ddma(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh);
-+extern void dwc_otg_hcd_qh_free_ddma(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh);
-+
-+/** @} */
-+
-+/** @name Internal Functions */
-+/** @{ */
-+dwc_otg_qh_t *dwc_urb_to_qh(dwc_otg_hcd_urb_t * urb);
-+/** @} */
-+
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+extern int dwc_otg_hcd_get_hc_for_lpm_tran(dwc_otg_hcd_t * hcd,
-+ uint8_t devaddr);
-+extern void dwc_otg_hcd_free_hc_from_lpm(dwc_otg_hcd_t * hcd);
-+#endif
-+
-+/** Gets the QH that contains the list_head */
-+#define dwc_list_to_qh(_list_head_ptr_) container_of(_list_head_ptr_, dwc_otg_qh_t, qh_list_entry)
-+
-+/** Gets the QTD that contains the list_head */
-+#define dwc_list_to_qtd(_list_head_ptr_) container_of(_list_head_ptr_, dwc_otg_qtd_t, qtd_list_entry)
-+
-+/** Check if QH is non-periodic */
-+#define dwc_qh_is_non_per(_qh_ptr_) ((_qh_ptr_->ep_type == UE_BULK) || \
-+ (_qh_ptr_->ep_type == UE_CONTROL))
-+
-+/** High bandwidth multiplier as encoded in highspeed endpoint descriptors */
-+#define dwc_hb_mult(wMaxPacketSize) (1 + (((wMaxPacketSize) >> 11) & 0x03))
-+
-+/** Packet size for any kind of endpoint descriptor */
-+#define dwc_max_packet(wMaxPacketSize) ((wMaxPacketSize) & 0x07ff)
-+
-+/**
-+ * Returns true if _frame1 is less than or equal to _frame2. The comparison is
-+ * done modulo DWC_HFNUM_MAX_FRNUM. This accounts for the rollover of the
-+ * frame number when the max frame number is reached.
-+ */
-+static inline int dwc_frame_num_le(uint16_t frame1, uint16_t frame2)
-+{
-+ return ((frame2 - frame1) & DWC_HFNUM_MAX_FRNUM) <=
-+ (DWC_HFNUM_MAX_FRNUM >> 1);
-+}
-+
-+/**
-+ * Returns true if _frame1 is greater than _frame2. The comparison is done
-+ * modulo DWC_HFNUM_MAX_FRNUM. This accounts for the rollover of the frame
-+ * number when the max frame number is reached.
-+ */
-+static inline int dwc_frame_num_gt(uint16_t frame1, uint16_t frame2)
-+{
-+ return (frame1 != frame2) &&
-+ (((frame1 - frame2) & DWC_HFNUM_MAX_FRNUM) <
-+ (DWC_HFNUM_MAX_FRNUM >> 1));
-+}
-+
-+/**
-+ * Increments _frame by the amount specified by _inc. The addition is done
-+ * modulo DWC_HFNUM_MAX_FRNUM. Returns the incremented value.
-+ */
-+static inline uint16_t dwc_frame_num_inc(uint16_t frame, uint16_t inc)
-+{
-+ return (frame + inc) & DWC_HFNUM_MAX_FRNUM;
-+}
-+
-+static inline uint16_t dwc_full_frame_num(uint16_t frame)
-+{
-+ return (frame & DWC_HFNUM_MAX_FRNUM) >> 3;
-+}
-+
-+static inline uint16_t dwc_micro_frame_num(uint16_t frame)
-+{
-+ return frame & 0x7;
-+}
-+
-+void dwc_otg_hcd_save_data_toggle(dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs,
-+ dwc_otg_qtd_t * qtd);
-+
-+#ifdef DEBUG
-+/**
-+ * Macro to sample the remaining PHY clocks left in the current frame. This
-+ * may be used during debugging to determine the average time it takes to
-+ * execute sections of code. There are two possible sample points, "a" and
-+ * "b", so the _letter argument must be one of these values.
-+ *
-+ * To dump the average sample times, read the "hcd_frrem" sysfs attribute. For
-+ * example, "cat /sys/devices/lm0/hcd_frrem".
-+ */
-+#define dwc_sample_frrem(_hcd, _qh, _letter) \
-+{ \
-+ hfnum_data_t hfnum; \
-+ dwc_otg_qtd_t *qtd; \
-+ qtd = list_entry(_qh->qtd_list.next, dwc_otg_qtd_t, qtd_list_entry); \
-+ if (usb_pipeint(qtd->urb->pipe) && _qh->start_split_frame != 0 && !qtd->complete_split) { \
-+ hfnum.d32 = DWC_READ_REG32(&_hcd->core_if->host_if->host_global_regs->hfnum); \
-+ switch (hfnum.b.frnum & 0x7) { \
-+ case 7: \
-+ _hcd->hfnum_7_samples_##_letter++; \
-+ _hcd->hfnum_7_frrem_accum_##_letter += hfnum.b.frrem; \
-+ break; \
-+ case 0: \
-+ _hcd->hfnum_0_samples_##_letter++; \
-+ _hcd->hfnum_0_frrem_accum_##_letter += hfnum.b.frrem; \
-+ break; \
-+ default: \
-+ _hcd->hfnum_other_samples_##_letter++; \
-+ _hcd->hfnum_other_frrem_accum_##_letter += hfnum.b.frrem; \
-+ break; \
-+ } \
-+ } \
-+}
-+#else
-+#define dwc_sample_frrem(_hcd, _qh, _letter)
-+#endif
-+#endif
-+#endif /* DWC_DEVICE_ONLY */
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_hcd_ddma.c
-@@ -0,0 +1,1132 @@
-+/*==========================================================================
-+ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_hcd_ddma.c $
-+ * $Revision: #10 $
-+ * $Date: 2011/10/20 $
-+ * $Change: 1869464 $
-+ *
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+#ifndef DWC_DEVICE_ONLY
-+
-+/** @file
-+ * This file contains Descriptor DMA support implementation for host mode.
-+ */
-+
-+#include "dwc_otg_hcd.h"
-+#include "dwc_otg_regs.h"
-+
-+extern bool microframe_schedule;
-+
-+static inline uint8_t frame_list_idx(uint16_t frame)
-+{
-+ return (frame & (MAX_FRLIST_EN_NUM - 1));
-+}
-+
-+static inline uint16_t desclist_idx_inc(uint16_t idx, uint16_t inc, uint8_t speed)
-+{
-+ return (idx + inc) &
-+ (((speed ==
-+ DWC_OTG_EP_SPEED_HIGH) ? MAX_DMA_DESC_NUM_HS_ISOC :
-+ MAX_DMA_DESC_NUM_GENERIC) - 1);
-+}
-+
-+static inline uint16_t desclist_idx_dec(uint16_t idx, uint16_t inc, uint8_t speed)
-+{
-+ return (idx - inc) &
-+ (((speed ==
-+ DWC_OTG_EP_SPEED_HIGH) ? MAX_DMA_DESC_NUM_HS_ISOC :
-+ MAX_DMA_DESC_NUM_GENERIC) - 1);
-+}
-+
-+static inline uint16_t max_desc_num(dwc_otg_qh_t * qh)
-+{
-+ return (((qh->ep_type == UE_ISOCHRONOUS)
-+ && (qh->dev_speed == DWC_OTG_EP_SPEED_HIGH))
-+ ? MAX_DMA_DESC_NUM_HS_ISOC : MAX_DMA_DESC_NUM_GENERIC);
-+}
-+static inline uint16_t frame_incr_val(dwc_otg_qh_t * qh)
-+{
-+ return ((qh->dev_speed == DWC_OTG_EP_SPEED_HIGH)
-+ ? ((qh->interval + 8 - 1) / 8)
-+ : qh->interval);
-+}
-+
-+static int desc_list_alloc(dwc_otg_qh_t * qh)
-+{
-+ int retval = 0;
-+
-+ qh->desc_list = (dwc_otg_host_dma_desc_t *)
-+ DWC_DMA_ALLOC(sizeof(dwc_otg_host_dma_desc_t) * max_desc_num(qh),
-+ &qh->desc_list_dma);
-+
-+ if (!qh->desc_list) {
-+ retval = -DWC_E_NO_MEMORY;
-+ DWC_ERROR("%s: DMA descriptor list allocation failed\n", __func__);
-+
-+ }
-+
-+ dwc_memset(qh->desc_list, 0x00,
-+ sizeof(dwc_otg_host_dma_desc_t) * max_desc_num(qh));
-+
-+ qh->n_bytes =
-+ (uint32_t *) DWC_ALLOC(sizeof(uint32_t) * max_desc_num(qh));
-+
-+ if (!qh->n_bytes) {
-+ retval = -DWC_E_NO_MEMORY;
-+ DWC_ERROR
-+ ("%s: Failed to allocate array for descriptors' size actual values\n",
-+ __func__);
-+
-+ }
-+ return retval;
-+
-+}
-+
-+static void desc_list_free(dwc_otg_qh_t * qh)
-+{
-+ if (qh->desc_list) {
-+ DWC_DMA_FREE(max_desc_num(qh), qh->desc_list,
-+ qh->desc_list_dma);
-+ qh->desc_list = NULL;
-+ }
-+
-+ if (qh->n_bytes) {
-+ DWC_FREE(qh->n_bytes);
-+ qh->n_bytes = NULL;
-+ }
-+}
-+
-+static int frame_list_alloc(dwc_otg_hcd_t * hcd)
-+{
-+ int retval = 0;
-+ if (hcd->frame_list)
-+ return 0;
-+
-+ hcd->frame_list = DWC_DMA_ALLOC(4 * MAX_FRLIST_EN_NUM,
-+ &hcd->frame_list_dma);
-+ if (!hcd->frame_list) {
-+ retval = -DWC_E_NO_MEMORY;
-+ DWC_ERROR("%s: Frame List allocation failed\n", __func__);
-+ }
-+
-+ dwc_memset(hcd->frame_list, 0x00, 4 * MAX_FRLIST_EN_NUM);
-+
-+ return retval;
-+}
-+
-+static void frame_list_free(dwc_otg_hcd_t * hcd)
-+{
-+ if (!hcd->frame_list)
-+ return;
-+
-+ DWC_DMA_FREE(4 * MAX_FRLIST_EN_NUM, hcd->frame_list, hcd->frame_list_dma);
-+ hcd->frame_list = NULL;
-+}
-+
-+static void per_sched_enable(dwc_otg_hcd_t * hcd, uint16_t fr_list_en)
-+{
-+
-+ hcfg_data_t hcfg;
-+
-+ hcfg.d32 = DWC_READ_REG32(&hcd->core_if->host_if->host_global_regs->hcfg);
-+
-+ if (hcfg.b.perschedena) {
-+ /* already enabled */
-+ return;
-+ }
-+
-+ DWC_WRITE_REG32(&hcd->core_if->host_if->host_global_regs->hflbaddr,
-+ hcd->frame_list_dma);
-+
-+ switch (fr_list_en) {
-+ case 64:
-+ hcfg.b.frlisten = 3;
-+ break;
-+ case 32:
-+ hcfg.b.frlisten = 2;
-+ break;
-+ case 16:
-+ hcfg.b.frlisten = 1;
-+ break;
-+ case 8:
-+ hcfg.b.frlisten = 0;
-+ break;
-+ default:
-+ break;
-+ }
-+
-+ hcfg.b.perschedena = 1;
-+
-+ DWC_DEBUGPL(DBG_HCD, "Enabling Periodic schedule\n");
-+ DWC_WRITE_REG32(&hcd->core_if->host_if->host_global_regs->hcfg, hcfg.d32);
-+
-+}
-+
-+static void per_sched_disable(dwc_otg_hcd_t * hcd)
-+{
-+ hcfg_data_t hcfg;
-+
-+ hcfg.d32 = DWC_READ_REG32(&hcd->core_if->host_if->host_global_regs->hcfg);
-+
-+ if (!hcfg.b.perschedena) {
-+ /* already disabled */
-+ return;
-+ }
-+ hcfg.b.perschedena = 0;
-+
-+ DWC_DEBUGPL(DBG_HCD, "Disabling Periodic schedule\n");
-+ DWC_WRITE_REG32(&hcd->core_if->host_if->host_global_regs->hcfg, hcfg.d32);
-+}
-+
-+/*
-+ * Activates/Deactivates FrameList entries for the channel
-+ * based on endpoint servicing period.
-+ */
-+void update_frame_list(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh, uint8_t enable)
-+{
-+ uint16_t i, j, inc;
-+ dwc_hc_t *hc = NULL;
-+
-+ if (!qh->channel) {
-+ DWC_ERROR("qh->channel = %p", qh->channel);
-+ return;
-+ }
-+
-+ if (!hcd) {
-+ DWC_ERROR("------hcd = %p", hcd);
-+ return;
-+ }
-+
-+ if (!hcd->frame_list) {
-+ DWC_ERROR("-------hcd->frame_list = %p", hcd->frame_list);
-+ return;
-+ }
-+
-+ hc = qh->channel;
-+ inc = frame_incr_val(qh);
-+ if (qh->ep_type == UE_ISOCHRONOUS)
-+ i = frame_list_idx(qh->sched_frame);
-+ else
-+ i = 0;
-+
-+ j = i;
-+ do {
-+ if (enable)
-+ hcd->frame_list[j] |= (1 << hc->hc_num);
-+ else
-+ hcd->frame_list[j] &= ~(1 << hc->hc_num);
-+ j = (j + inc) & (MAX_FRLIST_EN_NUM - 1);
-+ }
-+ while (j != i);
-+ if (!enable)
-+ return;
-+ hc->schinfo = 0;
-+ if (qh->channel->speed == DWC_OTG_EP_SPEED_HIGH) {
-+ j = 1;
-+ /* TODO - check this */
-+ inc = (8 + qh->interval - 1) / qh->interval;
-+ for (i = 0; i < inc; i++) {
-+ hc->schinfo |= j;
-+ j = j << qh->interval;
-+ }
-+ } else {
-+ hc->schinfo = 0xff;
-+ }
-+}
-+
-+#if 1
-+void dump_frame_list(dwc_otg_hcd_t * hcd)
-+{
-+ int i = 0;
-+ DWC_PRINTF("--FRAME LIST (hex) --\n");
-+ for (i = 0; i < MAX_FRLIST_EN_NUM; i++) {
-+ DWC_PRINTF("%x\t", hcd->frame_list[i]);
-+ if (!(i % 8) && i)
-+ DWC_PRINTF("\n");
-+ }
-+ DWC_PRINTF("\n----\n");
-+
-+}
-+#endif
-+
-+static void release_channel_ddma(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh)
-+{
-+ dwc_irqflags_t flags;
-+ dwc_spinlock_t *channel_lock = hcd->channel_lock;
-+
-+ dwc_hc_t *hc = qh->channel;
-+ if (dwc_qh_is_non_per(qh)) {
-+ DWC_SPINLOCK_IRQSAVE(channel_lock, &flags);
-+ if (!microframe_schedule)
-+ hcd->non_periodic_channels--;
-+ else
-+ hcd->available_host_channels++;
-+ DWC_SPINUNLOCK_IRQRESTORE(channel_lock, flags);
-+ } else
-+ update_frame_list(hcd, qh, 0);
-+
-+ /*
-+ * The condition is added to prevent double cleanup try in case of device
-+ * disconnect. See channel cleanup in dwc_otg_hcd_disconnect_cb().
-+ */
-+ if (hc->qh) {
-+ dwc_otg_hc_cleanup(hcd->core_if, hc);
-+ DWC_CIRCLEQ_INSERT_TAIL(&hcd->free_hc_list, hc, hc_list_entry);
-+ hc->qh = NULL;
-+ }
-+
-+ qh->channel = NULL;
-+ qh->ntd = 0;
-+
-+ if (qh->desc_list) {
-+ dwc_memset(qh->desc_list, 0x00,
-+ sizeof(dwc_otg_host_dma_desc_t) * max_desc_num(qh));
-+ }
-+}
-+
-+/**
-+ * Initializes a QH structure's Descriptor DMA related members.
-+ * Allocates memory for descriptor list.
-+ * On first periodic QH, allocates memory for FrameList
-+ * and enables periodic scheduling.
-+ *
-+ * @param hcd The HCD state structure for the DWC OTG controller.
-+ * @param qh The QH to init.
-+ *
-+ * @return 0 if successful, negative error code otherwise.
-+ */
-+int dwc_otg_hcd_qh_init_ddma(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh)
-+{
-+ int retval = 0;
-+
-+ if (qh->do_split) {
-+ DWC_ERROR("SPLIT Transfers are not supported in Descriptor DMA.\n");
-+ return -1;
-+ }
-+
-+ retval = desc_list_alloc(qh);
-+
-+ if ((retval == 0)
-+ && (qh->ep_type == UE_ISOCHRONOUS || qh->ep_type == UE_INTERRUPT)) {
-+ if (!hcd->frame_list) {
-+ retval = frame_list_alloc(hcd);
-+ /* Enable periodic schedule on first periodic QH */
-+ if (retval == 0)
-+ per_sched_enable(hcd, MAX_FRLIST_EN_NUM);
-+ }
-+ }
-+
-+ qh->ntd = 0;
-+
-+ return retval;
-+}
-+
-+/**
-+ * Frees descriptor list memory associated with the QH.
-+ * If QH is periodic and the last, frees FrameList memory
-+ * and disables periodic scheduling.
-+ *
-+ * @param hcd The HCD state structure for the DWC OTG controller.
-+ * @param qh The QH to init.
-+ */
-+void dwc_otg_hcd_qh_free_ddma(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh)
-+{
-+ desc_list_free(qh);
-+
-+ /*
-+ * Channel still assigned due to some reasons.
-+ * Seen on Isoc URB dequeue. Channel halted but no subsequent
-+ * ChHalted interrupt to release the channel. Afterwards
-+ * when it comes here from endpoint disable routine
-+ * channel remains assigned.
-+ */
-+ if (qh->channel)
-+ release_channel_ddma(hcd, qh);
-+
-+ if ((qh->ep_type == UE_ISOCHRONOUS || qh->ep_type == UE_INTERRUPT)
-+ && (microframe_schedule || !hcd->periodic_channels) && hcd->frame_list) {
-+
-+ per_sched_disable(hcd);
-+ frame_list_free(hcd);
-+ }
-+}
-+
-+static uint8_t frame_to_desc_idx(dwc_otg_qh_t * qh, uint16_t frame_idx)
-+{
-+ if (qh->dev_speed == DWC_OTG_EP_SPEED_HIGH) {
-+ /*
-+ * Descriptor set(8 descriptors) index
-+ * which is 8-aligned.
-+ */
-+ return (frame_idx & ((MAX_DMA_DESC_NUM_HS_ISOC / 8) - 1)) * 8;
-+ } else {
-+ return (frame_idx & (MAX_DMA_DESC_NUM_GENERIC - 1));
-+ }
-+}
-+
-+/*
-+ * Determine starting frame for Isochronous transfer.
-+ * Few frames skipped to prevent race condition with HC.
-+ */
-+static uint8_t calc_starting_frame(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh,
-+ uint8_t * skip_frames)
-+{
-+ uint16_t frame = 0;
-+ hcd->frame_number = dwc_otg_hcd_get_frame_number(hcd);
-+
-+ /* sched_frame is always frame number(not uFrame) both in FS and HS !! */
-+
-+ /*
-+ * skip_frames is used to limit activated descriptors number
-+ * to avoid the situation when HC services the last activated
-+ * descriptor firstly.
-+ * Example for FS:
-+ * Current frame is 1, scheduled frame is 3. Since HC always fetches the descriptor
-+ * corresponding to curr_frame+1, the descriptor corresponding to frame 2
-+ * will be fetched. If the number of descriptors is max=64 (or greather) the
-+ * list will be fully programmed with Active descriptors and it is possible
-+ * case(rare) that the latest descriptor(considering rollback) corresponding
-+ * to frame 2 will be serviced first. HS case is more probable because, in fact,
-+ * up to 11 uframes(16 in the code) may be skipped.
-+ */
-+ if (qh->dev_speed == DWC_OTG_EP_SPEED_HIGH) {
-+ /*
-+ * Consider uframe counter also, to start xfer asap.
-+ * If half of the frame elapsed skip 2 frames otherwise
-+ * just 1 frame.
-+ * Starting descriptor index must be 8-aligned, so
-+ * if the current frame is near to complete the next one
-+ * is skipped as well.
-+ */
-+
-+ if (dwc_micro_frame_num(hcd->frame_number) >= 5) {
-+ *skip_frames = 2 * 8;
-+ frame = dwc_frame_num_inc(hcd->frame_number, *skip_frames);
-+ } else {
-+ *skip_frames = 1 * 8;
-+ frame = dwc_frame_num_inc(hcd->frame_number, *skip_frames);
-+ }
-+
-+ frame = dwc_full_frame_num(frame);
-+ } else {
-+ /*
-+ * Two frames are skipped for FS - the current and the next.
-+ * But for descriptor programming, 1 frame(descriptor) is enough,
-+ * see example above.
-+ */
-+ *skip_frames = 1;
-+ frame = dwc_frame_num_inc(hcd->frame_number, 2);
-+ }
-+
-+ return frame;
-+}
-+
-+/*
-+ * Calculate initial descriptor index for isochronous transfer
-+ * based on scheduled frame.
-+ */
-+static uint8_t recalc_initial_desc_idx(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh)
-+{
-+ uint16_t frame = 0, fr_idx, fr_idx_tmp;
-+ uint8_t skip_frames = 0;
-+ /*
-+ * With current ISOC processing algorithm the channel is being
-+ * released when no more QTDs in the list(qh->ntd == 0).
-+ * Thus this function is called only when qh->ntd == 0 and qh->channel == 0.
-+ *
-+ * So qh->channel != NULL branch is not used and just not removed from the
-+ * source file. It is required for another possible approach which is,
-+ * do not disable and release the channel when ISOC session completed,
-+ * just move QH to inactive schedule until new QTD arrives.
-+ * On new QTD, the QH moved back to 'ready' schedule,
-+ * starting frame and therefore starting desc_index are recalculated.
-+ * In this case channel is released only on ep_disable.
-+ */
-+
-+ /* Calculate starting descriptor index. For INTERRUPT endpoint it is always 0. */
-+ if (qh->channel) {
-+ frame = calc_starting_frame(hcd, qh, &skip_frames);
-+ /*
-+ * Calculate initial descriptor index based on FrameList current bitmap
-+ * and servicing period.
-+ */
-+ fr_idx_tmp = frame_list_idx(frame);
-+ fr_idx =
-+ (MAX_FRLIST_EN_NUM + frame_list_idx(qh->sched_frame) -
-+ fr_idx_tmp)
-+ % frame_incr_val(qh);
-+ fr_idx = (fr_idx + fr_idx_tmp) % MAX_FRLIST_EN_NUM;
-+ } else {
-+ qh->sched_frame = calc_starting_frame(hcd, qh, &skip_frames);
-+ fr_idx = frame_list_idx(qh->sched_frame);
-+ }
-+
-+ qh->td_first = qh->td_last = frame_to_desc_idx(qh, fr_idx);
-+
-+ return skip_frames;
-+}
-+
-+#define ISOC_URB_GIVEBACK_ASAP
-+
-+#define MAX_ISOC_XFER_SIZE_FS 1023
-+#define MAX_ISOC_XFER_SIZE_HS 3072
-+#define DESCNUM_THRESHOLD 4
-+
-+static void init_isoc_dma_desc(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh,
-+ uint8_t skip_frames)
-+{
-+ struct dwc_otg_hcd_iso_packet_desc *frame_desc;
-+ dwc_otg_qtd_t *qtd;
-+ dwc_otg_host_dma_desc_t *dma_desc;
-+ uint16_t idx, inc, n_desc, ntd_max, max_xfer_size;
-+
-+ idx = qh->td_last;
-+ inc = qh->interval;
-+ n_desc = 0;
-+
-+ ntd_max = (max_desc_num(qh) + qh->interval - 1) / qh->interval;
-+ if (skip_frames && !qh->channel)
-+ ntd_max = ntd_max - skip_frames / qh->interval;
-+
-+ max_xfer_size =
-+ (qh->dev_speed ==
-+ DWC_OTG_EP_SPEED_HIGH) ? MAX_ISOC_XFER_SIZE_HS :
-+ MAX_ISOC_XFER_SIZE_FS;
-+
-+ DWC_CIRCLEQ_FOREACH(qtd, &qh->qtd_list, qtd_list_entry) {
-+ while ((qh->ntd < ntd_max)
-+ && (qtd->isoc_frame_index_last <
-+ qtd->urb->packet_count)) {
-+
-+ dma_desc = &qh->desc_list[idx];
-+ dwc_memset(dma_desc, 0x00, sizeof(dwc_otg_host_dma_desc_t));
-+
-+ frame_desc = &qtd->urb->iso_descs[qtd->isoc_frame_index_last];
-+
-+ if (frame_desc->length > max_xfer_size)
-+ qh->n_bytes[idx] = max_xfer_size;
-+ else
-+ qh->n_bytes[idx] = frame_desc->length;
-+ dma_desc->status.b_isoc.n_bytes = qh->n_bytes[idx];
-+ dma_desc->status.b_isoc.a = 1;
-+ dma_desc->status.b_isoc.sts = 0;
-+
-+ dma_desc->buf = qtd->urb->dma + frame_desc->offset;
-+
-+ qh->ntd++;
-+
-+ qtd->isoc_frame_index_last++;
-+
-+#ifdef ISOC_URB_GIVEBACK_ASAP
-+ /*
-+ * Set IOC for each descriptor corresponding to the
-+ * last frame of the URB.
-+ */
-+ if (qtd->isoc_frame_index_last ==
-+ qtd->urb->packet_count)
-+ dma_desc->status.b_isoc.ioc = 1;
-+
-+#endif
-+ idx = desclist_idx_inc(idx, inc, qh->dev_speed);
-+ n_desc++;
-+
-+ }
-+ qtd->in_process = 1;
-+ }
-+
-+ qh->td_last = idx;
-+
-+#ifdef ISOC_URB_GIVEBACK_ASAP
-+ /* Set IOC for the last descriptor if descriptor list is full */
-+ if (qh->ntd == ntd_max) {
-+ idx = desclist_idx_dec(qh->td_last, inc, qh->dev_speed);
-+ qh->desc_list[idx].status.b_isoc.ioc = 1;
-+ }
-+#else
-+ /*
-+ * Set IOC bit only for one descriptor.
-+ * Always try to be ahead of HW processing,
-+ * i.e. on IOC generation driver activates next descriptors but
-+ * core continues to process descriptors followed the one with IOC set.
-+ */
-+
-+ if (n_desc > DESCNUM_THRESHOLD) {
-+ /*
-+ * Move IOC "up". Required even if there is only one QTD
-+ * in the list, cause QTDs migth continue to be queued,
-+ * but during the activation it was only one queued.
-+ * Actually more than one QTD might be in the list if this function called
-+ * from XferCompletion - QTDs was queued during HW processing of the previous
-+ * descriptor chunk.
-+ */
-+ idx = dwc_desclist_idx_dec(idx, inc * ((qh->ntd + 1) / 2), qh->dev_speed);
-+ } else {
-+ /*
-+ * Set the IOC for the latest descriptor
-+ * if either number of descriptor is not greather than threshold
-+ * or no more new descriptors activated.
-+ */
-+ idx = dwc_desclist_idx_dec(qh->td_last, inc, qh->dev_speed);
-+ }
-+
-+ qh->desc_list[idx].status.b_isoc.ioc = 1;
-+#endif
-+}
-+
-+static void init_non_isoc_dma_desc(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh)
-+{
-+
-+ dwc_hc_t *hc;
-+ dwc_otg_host_dma_desc_t *dma_desc;
-+ dwc_otg_qtd_t *qtd;
-+ int num_packets, len, n_desc = 0;
-+
-+ hc = qh->channel;
-+
-+ /*
-+ * Start with hc->xfer_buff initialized in
-+ * assign_and_init_hc(), then if SG transfer consists of multiple URBs,
-+ * this pointer re-assigned to the buffer of the currently processed QTD.
-+ * For non-SG request there is always one QTD active.
-+ */
-+
-+ DWC_CIRCLEQ_FOREACH(qtd, &qh->qtd_list, qtd_list_entry) {
-+
-+ if (n_desc) {
-+ /* SG request - more than 1 QTDs */
-+ hc->xfer_buff = (uint8_t *)qtd->urb->dma + qtd->urb->actual_length;
-+ hc->xfer_len = qtd->urb->length - qtd->urb->actual_length;
-+ }
-+
-+ qtd->n_desc = 0;
-+
-+ do {
-+ dma_desc = &qh->desc_list[n_desc];
-+ len = hc->xfer_len;
-+
-+ if (len > MAX_DMA_DESC_SIZE)
-+ len = MAX_DMA_DESC_SIZE - hc->max_packet + 1;
-+
-+ if (hc->ep_is_in) {
-+ if (len > 0) {
-+ num_packets = (len + hc->max_packet - 1) / hc->max_packet;
-+ } else {
-+ /* Need 1 packet for transfer length of 0. */
-+ num_packets = 1;
-+ }
-+ /* Always program an integral # of max packets for IN transfers. */
-+ len = num_packets * hc->max_packet;
-+ }
-+
-+ dma_desc->status.b.n_bytes = len;
-+
-+ qh->n_bytes[n_desc] = len;
-+
-+ if ((qh->ep_type == UE_CONTROL)
-+ && (qtd->control_phase == DWC_OTG_CONTROL_SETUP))
-+ dma_desc->status.b.sup = 1; /* Setup Packet */
-+
-+ dma_desc->status.b.a = 1; /* Active descriptor */
-+ dma_desc->status.b.sts = 0;
-+
-+ dma_desc->buf =
-+ ((unsigned long)hc->xfer_buff & 0xffffffff);
-+
-+ /*
-+ * Last descriptor(or single) of IN transfer
-+ * with actual size less than MaxPacket.
-+ */
-+ if (len > hc->xfer_len) {
-+ hc->xfer_len = 0;
-+ } else {
-+ hc->xfer_buff += len;
-+ hc->xfer_len -= len;
-+ }
-+
-+ qtd->n_desc++;
-+ n_desc++;
-+ }
-+ while ((hc->xfer_len > 0) && (n_desc != MAX_DMA_DESC_NUM_GENERIC));
-+
-+
-+ qtd->in_process = 1;
-+
-+ if (qh->ep_type == UE_CONTROL)
-+ break;
-+
-+ if (n_desc == MAX_DMA_DESC_NUM_GENERIC)
-+ break;
-+ }
-+
-+ if (n_desc) {
-+ /* Request Transfer Complete interrupt for the last descriptor */
-+ qh->desc_list[n_desc - 1].status.b.ioc = 1;
-+ /* End of List indicator */
-+ qh->desc_list[n_desc - 1].status.b.eol = 1;
-+
-+ hc->ntd = n_desc;
-+ }
-+}
-+
-+/**
-+ * For Control and Bulk endpoints initializes descriptor list
-+ * and starts the transfer.
-+ *
-+ * For Interrupt and Isochronous endpoints initializes descriptor list
-+ * then updates FrameList, marking appropriate entries as active.
-+ * In case of Isochronous, the starting descriptor index is calculated based
-+ * on the scheduled frame, but only on the first transfer descriptor within a session.
-+ * Then starts the transfer via enabling the channel.
-+ * For Isochronous endpoint the channel is not halted on XferComplete
-+ * interrupt so remains assigned to the endpoint(QH) until session is done.
-+ *
-+ * @param hcd The HCD state structure for the DWC OTG controller.
-+ * @param qh The QH to init.
-+ *
-+ * @return 0 if successful, negative error code otherwise.
-+ */
-+void dwc_otg_hcd_start_xfer_ddma(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh)
-+{
-+ /* Channel is already assigned */
-+ dwc_hc_t *hc = qh->channel;
-+ uint8_t skip_frames = 0;
-+
-+ switch (hc->ep_type) {
-+ case DWC_OTG_EP_TYPE_CONTROL:
-+ case DWC_OTG_EP_TYPE_BULK:
-+ init_non_isoc_dma_desc(hcd, qh);
-+
-+ dwc_otg_hc_start_transfer_ddma(hcd->core_if, hc);
-+ break;
-+ case DWC_OTG_EP_TYPE_INTR:
-+ init_non_isoc_dma_desc(hcd, qh);
-+
-+ update_frame_list(hcd, qh, 1);
-+
-+ dwc_otg_hc_start_transfer_ddma(hcd->core_if, hc);
-+ break;
-+ case DWC_OTG_EP_TYPE_ISOC:
-+
-+ if (!qh->ntd)
-+ skip_frames = recalc_initial_desc_idx(hcd, qh);
-+
-+ init_isoc_dma_desc(hcd, qh, skip_frames);
-+
-+ if (!hc->xfer_started) {
-+
-+ update_frame_list(hcd, qh, 1);
-+
-+ /*
-+ * Always set to max, instead of actual size.
-+ * Otherwise ntd will be changed with
-+ * channel being enabled. Not recommended.
-+ *
-+ */
-+ hc->ntd = max_desc_num(qh);
-+ /* Enable channel only once for ISOC */
-+ dwc_otg_hc_start_transfer_ddma(hcd->core_if, hc);
-+ }
-+
-+ break;
-+ default:
-+
-+ break;
-+ }
-+}
-+
-+static void complete_isoc_xfer_ddma(dwc_otg_hcd_t * hcd,
-+ dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs,
-+ dwc_otg_halt_status_e halt_status)
-+{
-+ struct dwc_otg_hcd_iso_packet_desc *frame_desc;
-+ dwc_otg_qtd_t *qtd, *qtd_tmp;
-+ dwc_otg_qh_t *qh;
-+ dwc_otg_host_dma_desc_t *dma_desc;
-+ uint16_t idx, remain;
-+ uint8_t urb_compl;
-+
-+ qh = hc->qh;
-+ idx = qh->td_first;
-+
-+ if (hc->halt_status == DWC_OTG_HC_XFER_URB_DEQUEUE) {
-+ DWC_CIRCLEQ_FOREACH_SAFE(qtd, qtd_tmp, &hc->qh->qtd_list, qtd_list_entry)
-+ qtd->in_process = 0;
-+ return;
-+ } else if ((halt_status == DWC_OTG_HC_XFER_AHB_ERR) ||
-+ (halt_status == DWC_OTG_HC_XFER_BABBLE_ERR)) {
-+ /*
-+ * Channel is halted in these error cases.
-+ * Considered as serious issues.
-+ * Complete all URBs marking all frames as failed,
-+ * irrespective whether some of the descriptors(frames) succeeded or no.
-+ * Pass error code to completion routine as well, to
-+ * update urb->status, some of class drivers might use it to stop
-+ * queing transfer requests.
-+ */
-+ int err = (halt_status == DWC_OTG_HC_XFER_AHB_ERR)
-+ ? (-DWC_E_IO)
-+ : (-DWC_E_OVERFLOW);
-+
-+ DWC_CIRCLEQ_FOREACH_SAFE(qtd, qtd_tmp, &hc->qh->qtd_list, qtd_list_entry) {
-+ for (idx = 0; idx < qtd->urb->packet_count; idx++) {
-+ frame_desc = &qtd->urb->iso_descs[idx];
-+ frame_desc->status = err;
-+ }
-+ hcd->fops->complete(hcd, qtd->urb->priv, qtd->urb, err);
-+ dwc_otg_hcd_qtd_remove_and_free(hcd, qtd, qh);
-+ }
-+ return;
-+ }
-+
-+ DWC_CIRCLEQ_FOREACH_SAFE(qtd, qtd_tmp, &hc->qh->qtd_list, qtd_list_entry) {
-+
-+ if (!qtd->in_process)
-+ break;
-+
-+ urb_compl = 0;
-+
-+ do {
-+
-+ dma_desc = &qh->desc_list[idx];
-+
-+ frame_desc = &qtd->urb->iso_descs[qtd->isoc_frame_index];
-+ remain = hc->ep_is_in ? dma_desc->status.b_isoc.n_bytes : 0;
-+
-+ if (dma_desc->status.b_isoc.sts == DMA_DESC_STS_PKTERR) {
-+ /*
-+ * XactError or, unable to complete all the transactions
-+ * in the scheduled micro-frame/frame,
-+ * both indicated by DMA_DESC_STS_PKTERR.
-+ */
-+ qtd->urb->error_count++;
-+ frame_desc->actual_length = qh->n_bytes[idx] - remain;
-+ frame_desc->status = -DWC_E_PROTOCOL;
-+ } else {
-+ /* Success */
-+
-+ frame_desc->actual_length = qh->n_bytes[idx] - remain;
-+ frame_desc->status = 0;
-+ }
-+
-+ if (++qtd->isoc_frame_index == qtd->urb->packet_count) {
-+ /*
-+ * urb->status is not used for isoc transfers here.
-+ * The individual frame_desc status are used instead.
-+ */
-+
-+ hcd->fops->complete(hcd, qtd->urb->priv, qtd->urb, 0);
-+ dwc_otg_hcd_qtd_remove_and_free(hcd, qtd, qh);
-+
-+ /*
-+ * This check is necessary because urb_dequeue can be called
-+ * from urb complete callback(sound driver example).
-+ * All pending URBs are dequeued there, so no need for
-+ * further processing.
-+ */
-+ if (hc->halt_status == DWC_OTG_HC_XFER_URB_DEQUEUE) {
-+ return;
-+ }
-+
-+ urb_compl = 1;
-+
-+ }
-+
-+ qh->ntd--;
-+
-+ /* Stop if IOC requested descriptor reached */
-+ if (dma_desc->status.b_isoc.ioc) {
-+ idx = desclist_idx_inc(idx, qh->interval, hc->speed);
-+ goto stop_scan;
-+ }
-+
-+ idx = desclist_idx_inc(idx, qh->interval, hc->speed);
-+
-+ if (urb_compl)
-+ break;
-+ }
-+ while (idx != qh->td_first);
-+ }
-+stop_scan:
-+ qh->td_first = idx;
-+}
-+
-+uint8_t update_non_isoc_urb_state_ddma(dwc_otg_hcd_t * hcd,
-+ dwc_hc_t * hc,
-+ dwc_otg_qtd_t * qtd,
-+ dwc_otg_host_dma_desc_t * dma_desc,
-+ dwc_otg_halt_status_e halt_status,
-+ uint32_t n_bytes, uint8_t * xfer_done)
-+{
-+
-+ uint16_t remain = hc->ep_is_in ? dma_desc->status.b.n_bytes : 0;
-+ dwc_otg_hcd_urb_t *urb = qtd->urb;
-+
-+ if (halt_status == DWC_OTG_HC_XFER_AHB_ERR) {
-+ urb->status = -DWC_E_IO;
-+ return 1;
-+ }
-+ if (dma_desc->status.b.sts == DMA_DESC_STS_PKTERR) {
-+ switch (halt_status) {
-+ case DWC_OTG_HC_XFER_STALL:
-+ urb->status = -DWC_E_PIPE;
-+ break;
-+ case DWC_OTG_HC_XFER_BABBLE_ERR:
-+ urb->status = -DWC_E_OVERFLOW;
-+ break;
-+ case DWC_OTG_HC_XFER_XACT_ERR:
-+ urb->status = -DWC_E_PROTOCOL;
-+ break;
-+ default:
-+ DWC_ERROR("%s: Unhandled descriptor error status (%d)\n", __func__,
-+ halt_status);
-+ break;
-+ }
-+ return 1;
-+ }
-+
-+ if (dma_desc->status.b.a == 1) {
-+ DWC_DEBUGPL(DBG_HCDV,
-+ "Active descriptor encountered on channel %d\n",
-+ hc->hc_num);
-+ return 0;
-+ }
-+
-+ if (hc->ep_type == DWC_OTG_EP_TYPE_CONTROL) {
-+ if (qtd->control_phase == DWC_OTG_CONTROL_DATA) {
-+ urb->actual_length += n_bytes - remain;
-+ if (remain || urb->actual_length == urb->length) {
-+ /*
-+ * For Control Data stage do not set urb->status=0 to prevent
-+ * URB callback. Set it when Status phase done. See below.
-+ */
-+ *xfer_done = 1;
-+ }
-+
-+ } else if (qtd->control_phase == DWC_OTG_CONTROL_STATUS) {
-+ urb->status = 0;
-+ *xfer_done = 1;
-+ }
-+ /* No handling for SETUP stage */
-+ } else {
-+ /* BULK and INTR */
-+ urb->actual_length += n_bytes - remain;
-+ if (remain || urb->actual_length == urb->length) {
-+ urb->status = 0;
-+ *xfer_done = 1;
-+ }
-+ }
-+
-+ return 0;
-+}
-+
-+static void complete_non_isoc_xfer_ddma(dwc_otg_hcd_t * hcd,
-+ dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs,
-+ dwc_otg_halt_status_e halt_status)
-+{
-+ dwc_otg_hcd_urb_t *urb = NULL;
-+ dwc_otg_qtd_t *qtd, *qtd_tmp;
-+ dwc_otg_qh_t *qh;
-+ dwc_otg_host_dma_desc_t *dma_desc;
-+ uint32_t n_bytes, n_desc, i;
-+ uint8_t failed = 0, xfer_done;
-+
-+ n_desc = 0;
-+
-+ qh = hc->qh;
-+
-+ if (hc->halt_status == DWC_OTG_HC_XFER_URB_DEQUEUE) {
-+ DWC_CIRCLEQ_FOREACH_SAFE(qtd, qtd_tmp, &hc->qh->qtd_list, qtd_list_entry) {
-+ qtd->in_process = 0;
-+ }
-+ return;
-+ }
-+
-+ DWC_CIRCLEQ_FOREACH_SAFE(qtd, qtd_tmp, &qh->qtd_list, qtd_list_entry) {
-+
-+ urb = qtd->urb;
-+
-+ n_bytes = 0;
-+ xfer_done = 0;
-+
-+ for (i = 0; i < qtd->n_desc; i++) {
-+ dma_desc = &qh->desc_list[n_desc];
-+
-+ n_bytes = qh->n_bytes[n_desc];
-+
-+ failed =
-+ update_non_isoc_urb_state_ddma(hcd, hc, qtd,
-+ dma_desc,
-+ halt_status, n_bytes,
-+ &xfer_done);
-+
-+ if (failed
-+ || (xfer_done
-+ && (urb->status != -DWC_E_IN_PROGRESS))) {
-+
-+ hcd->fops->complete(hcd, urb->priv, urb,
-+ urb->status);
-+ dwc_otg_hcd_qtd_remove_and_free(hcd, qtd, qh);
-+
-+ if (failed)
-+ goto stop_scan;
-+ } else if (qh->ep_type == UE_CONTROL) {
-+ if (qtd->control_phase == DWC_OTG_CONTROL_SETUP) {
-+ if (urb->length > 0) {
-+ qtd->control_phase = DWC_OTG_CONTROL_DATA;
-+ } else {
-+ qtd->control_phase = DWC_OTG_CONTROL_STATUS;
-+ }
-+ DWC_DEBUGPL(DBG_HCDV, " Control setup transaction done\n");
-+ } else if (qtd->control_phase == DWC_OTG_CONTROL_DATA) {
-+ if (xfer_done) {
-+ qtd->control_phase = DWC_OTG_CONTROL_STATUS;
-+ DWC_DEBUGPL(DBG_HCDV, " Control data transfer done\n");
-+ } else if (i + 1 == qtd->n_desc) {
-+ /*
-+ * Last descriptor for Control data stage which is
-+ * not completed yet.
-+ */
-+ dwc_otg_hcd_save_data_toggle(hc, hc_regs, qtd);
-+ }
-+ }
-+ }
-+
-+ n_desc++;
-+ }
-+
-+ }
-+
-+stop_scan:
-+
-+ if (qh->ep_type != UE_CONTROL) {
-+ /*
-+ * Resetting the data toggle for bulk
-+ * and interrupt endpoints in case of stall. See handle_hc_stall_intr()
-+ */
-+ if (halt_status == DWC_OTG_HC_XFER_STALL)
-+ qh->data_toggle = DWC_OTG_HC_PID_DATA0;
-+ else
-+ dwc_otg_hcd_save_data_toggle(hc, hc_regs, qtd);
-+ }
-+
-+ if (halt_status == DWC_OTG_HC_XFER_COMPLETE) {
-+ hcint_data_t hcint;
-+ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint);
-+ if (hcint.b.nyet) {
-+ /*
-+ * Got a NYET on the last transaction of the transfer. It
-+ * means that the endpoint should be in the PING state at the
-+ * beginning of the next transfer.
-+ */
-+ qh->ping_state = 1;
-+ clear_hc_int(hc_regs, nyet);
-+ }
-+
-+ }
-+
-+}
-+
-+/**
-+ * This function is called from interrupt handlers.
-+ * Scans the descriptor list, updates URB's status and
-+ * calls completion routine for the URB if it's done.
-+ * Releases the channel to be used by other transfers.
-+ * In case of Isochronous endpoint the channel is not halted until
-+ * the end of the session, i.e. QTD list is empty.
-+ * If periodic channel released the FrameList is updated accordingly.
-+ *
-+ * Calls transaction selection routines to activate pending transfers.
-+ *
-+ * @param hcd The HCD state structure for the DWC OTG controller.
-+ * @param hc Host channel, the transfer is completed on.
-+ * @param hc_regs Host channel registers.
-+ * @param halt_status Reason the channel is being halted,
-+ * or just XferComplete for isochronous transfer
-+ */
-+void dwc_otg_hcd_complete_xfer_ddma(dwc_otg_hcd_t * hcd,
-+ dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs,
-+ dwc_otg_halt_status_e halt_status)
-+{
-+ uint8_t continue_isoc_xfer = 0;
-+ dwc_otg_transaction_type_e tr_type;
-+ dwc_otg_qh_t *qh = hc->qh;
-+
-+ if (hc->ep_type == DWC_OTG_EP_TYPE_ISOC) {
-+
-+ complete_isoc_xfer_ddma(hcd, hc, hc_regs, halt_status);
-+
-+ /* Release the channel if halted or session completed */
-+ if (halt_status != DWC_OTG_HC_XFER_COMPLETE ||
-+ DWC_CIRCLEQ_EMPTY(&qh->qtd_list)) {
-+
-+ /* Halt the channel if session completed */
-+ if (halt_status == DWC_OTG_HC_XFER_COMPLETE) {
-+ dwc_otg_hc_halt(hcd->core_if, hc, halt_status);
-+ }
-+
-+ release_channel_ddma(hcd, qh);
-+ dwc_otg_hcd_qh_remove(hcd, qh);
-+ } else {
-+ /* Keep in assigned schedule to continue transfer */
-+ DWC_LIST_MOVE_HEAD(&hcd->periodic_sched_assigned,
-+ &qh->qh_list_entry);
-+ continue_isoc_xfer = 1;
-+
-+ }
-+ /** @todo Consider the case when period exceeds FrameList size.
-+ * Frame Rollover interrupt should be used.
-+ */
-+ } else {
-+ /* Scan descriptor list to complete the URB(s), then release the channel */
-+ complete_non_isoc_xfer_ddma(hcd, hc, hc_regs, halt_status);
-+
-+ release_channel_ddma(hcd, qh);
-+ dwc_otg_hcd_qh_remove(hcd, qh);
-+
-+ if (!DWC_CIRCLEQ_EMPTY(&qh->qtd_list)) {
-+ /* Add back to inactive non-periodic schedule on normal completion */
-+ dwc_otg_hcd_qh_add(hcd, qh);
-+ }
-+
-+ }
-+ tr_type = dwc_otg_hcd_select_transactions(hcd);
-+ if (tr_type != DWC_OTG_TRANSACTION_NONE || continue_isoc_xfer) {
-+ if (continue_isoc_xfer) {
-+ if (tr_type == DWC_OTG_TRANSACTION_NONE) {
-+ tr_type = DWC_OTG_TRANSACTION_PERIODIC;
-+ } else if (tr_type == DWC_OTG_TRANSACTION_NON_PERIODIC) {
-+ tr_type = DWC_OTG_TRANSACTION_ALL;
-+ }
-+ }
-+ dwc_otg_hcd_queue_transactions(hcd, tr_type);
-+ }
-+}
-+
-+#endif /* DWC_DEVICE_ONLY */
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_hcd_if.h
-@@ -0,0 +1,417 @@
-+/* ==========================================================================
-+ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_hcd_if.h $
-+ * $Revision: #12 $
-+ * $Date: 2011/10/26 $
-+ * $Change: 1873028 $
-+ *
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+#ifndef DWC_DEVICE_ONLY
-+#ifndef __DWC_HCD_IF_H__
-+#define __DWC_HCD_IF_H__
-+
-+#include "dwc_otg_core_if.h"
-+
-+/** @file
-+ * This file defines DWC_OTG HCD Core API.
-+ */
-+
-+struct dwc_otg_hcd;
-+typedef struct dwc_otg_hcd dwc_otg_hcd_t;
-+
-+struct dwc_otg_hcd_urb;
-+typedef struct dwc_otg_hcd_urb dwc_otg_hcd_urb_t;
-+
-+/** @name HCD Function Driver Callbacks */
-+/** @{ */
-+
-+/** This function is called whenever core switches to host mode. */
-+typedef int (*dwc_otg_hcd_start_cb_t) (dwc_otg_hcd_t * hcd);
-+
-+/** This function is called when device has been disconnected */
-+typedef int (*dwc_otg_hcd_disconnect_cb_t) (dwc_otg_hcd_t * hcd);
-+
-+/** Wrapper provides this function to HCD to core, so it can get hub information to which device is connected */
-+typedef int (*dwc_otg_hcd_hub_info_from_urb_cb_t) (dwc_otg_hcd_t * hcd,
-+ void *urb_handle,
-+ uint32_t * hub_addr,
-+ uint32_t * port_addr);
-+/** Via this function HCD core gets device speed */
-+typedef int (*dwc_otg_hcd_speed_from_urb_cb_t) (dwc_otg_hcd_t * hcd,
-+ void *urb_handle);
-+
-+/** This function is called when urb is completed */
-+typedef int (*dwc_otg_hcd_complete_urb_cb_t) (dwc_otg_hcd_t * hcd,
-+ void *urb_handle,
-+ dwc_otg_hcd_urb_t * dwc_otg_urb,
-+ int32_t status);
-+
-+/** Via this function HCD core gets b_hnp_enable parameter */
-+typedef int (*dwc_otg_hcd_get_b_hnp_enable) (dwc_otg_hcd_t * hcd);
-+
-+struct dwc_otg_hcd_function_ops {
-+ dwc_otg_hcd_start_cb_t start;
-+ dwc_otg_hcd_disconnect_cb_t disconnect;
-+ dwc_otg_hcd_hub_info_from_urb_cb_t hub_info;
-+ dwc_otg_hcd_speed_from_urb_cb_t speed;
-+ dwc_otg_hcd_complete_urb_cb_t complete;
-+ dwc_otg_hcd_get_b_hnp_enable get_b_hnp_enable;
-+};
-+/** @} */
-+
-+/** @name HCD Core API */
-+/** @{ */
-+/** This function allocates dwc_otg_hcd structure and returns pointer on it. */
-+extern dwc_otg_hcd_t *dwc_otg_hcd_alloc_hcd(void);
-+
-+/** This function should be called to initiate HCD Core.
-+ *
-+ * @param hcd The HCD
-+ * @param core_if The DWC_OTG Core
-+ *
-+ * Returns -DWC_E_NO_MEMORY if no enough memory.
-+ * Returns 0 on success
-+ */
-+extern int dwc_otg_hcd_init(dwc_otg_hcd_t * hcd, dwc_otg_core_if_t * core_if);
-+
-+/** Frees HCD
-+ *
-+ * @param hcd The HCD
-+ */
-+extern void dwc_otg_hcd_remove(dwc_otg_hcd_t * hcd);
-+
-+/** This function should be called on every hardware interrupt.
-+ *
-+ * @param dwc_otg_hcd The HCD
-+ *
-+ * Returns non zero if interrupt is handled
-+ * Return 0 if interrupt is not handled
-+ */
-+extern int32_t dwc_otg_hcd_handle_intr(dwc_otg_hcd_t * dwc_otg_hcd);
-+
-+/** This function is used to handle the fast interrupt
-+ *
-+ */
-+extern void __attribute__ ((naked)) dwc_otg_hcd_handle_fiq(void);
-+
-+/**
-+ * Returns private data set by
-+ * dwc_otg_hcd_set_priv_data function.
-+ *
-+ * @param hcd The HCD
-+ */
-+extern void *dwc_otg_hcd_get_priv_data(dwc_otg_hcd_t * hcd);
-+
-+/**
-+ * Set private data.
-+ *
-+ * @param hcd The HCD
-+ * @param priv_data pointer to be stored in private data
-+ */
-+extern void dwc_otg_hcd_set_priv_data(dwc_otg_hcd_t * hcd, void *priv_data);
-+
-+/**
-+ * This function initializes the HCD Core.
-+ *
-+ * @param hcd The HCD
-+ * @param fops The Function Driver Operations data structure containing pointers to all callbacks.
-+ *
-+ * Returns -DWC_E_NO_DEVICE if Core is currently is in device mode.
-+ * Returns 0 on success
-+ */
-+extern int dwc_otg_hcd_start(dwc_otg_hcd_t * hcd,
-+ struct dwc_otg_hcd_function_ops *fops);
-+
-+/**
-+ * Halts the DWC_otg host mode operations in a clean manner. USB transfers are
-+ * stopped.
-+ *
-+ * @param hcd The HCD
-+ */
-+extern void dwc_otg_hcd_stop(dwc_otg_hcd_t * hcd);
-+
-+/**
-+ * Handles hub class-specific requests.
-+ *
-+ * @param dwc_otg_hcd The HCD
-+ * @param typeReq Request Type
-+ * @param wValue wValue from control request
-+ * @param wIndex wIndex from control request
-+ * @param buf data buffer
-+ * @param wLength data buffer length
-+ *
-+ * Returns -DWC_E_INVALID if invalid argument is passed
-+ * Returns 0 on success
-+ */
-+extern int dwc_otg_hcd_hub_control(dwc_otg_hcd_t * dwc_otg_hcd,
-+ uint16_t typeReq, uint16_t wValue,
-+ uint16_t wIndex, uint8_t * buf,
-+ uint16_t wLength);
-+
-+/**
-+ * Returns otg port number.
-+ *
-+ * @param hcd The HCD
-+ */
-+extern uint32_t dwc_otg_hcd_otg_port(dwc_otg_hcd_t * hcd);
-+
-+/**
-+ * Returns OTG version - either 1.3 or 2.0.
-+ *
-+ * @param core_if The core_if structure pointer
-+ */
-+extern uint16_t dwc_otg_get_otg_version(dwc_otg_core_if_t * core_if);
-+
-+/**
-+ * Returns 1 if currently core is acting as B host, and 0 otherwise.
-+ *
-+ * @param hcd The HCD
-+ */
-+extern uint32_t dwc_otg_hcd_is_b_host(dwc_otg_hcd_t * hcd);
-+
-+/**
-+ * Returns current frame number.
-+ *
-+ * @param hcd The HCD
-+ */
-+extern int dwc_otg_hcd_get_frame_number(dwc_otg_hcd_t * hcd);
-+
-+/**
-+ * Dumps hcd state.
-+ *
-+ * @param hcd The HCD
-+ */
-+extern void dwc_otg_hcd_dump_state(dwc_otg_hcd_t * hcd);
-+
-+/**
-+ * Dump the average frame remaining at SOF. This can be used to
-+ * determine average interrupt latency. Frame remaining is also shown for
-+ * start transfer and two additional sample points.
-+ * Currently this function is not implemented.
-+ *
-+ * @param hcd The HCD
-+ */
-+extern void dwc_otg_hcd_dump_frrem(dwc_otg_hcd_t * hcd);
-+
-+/**
-+ * Sends LPM transaction to the local device.
-+ *
-+ * @param hcd The HCD
-+ * @param devaddr Device Address
-+ * @param hird Host initiated resume duration
-+ * @param bRemoteWake Value of bRemoteWake field in LPM transaction
-+ *
-+ * Returns negative value if sending LPM transaction was not succeeded.
-+ * Returns 0 on success.
-+ */
-+extern int dwc_otg_hcd_send_lpm(dwc_otg_hcd_t * hcd, uint8_t devaddr,
-+ uint8_t hird, uint8_t bRemoteWake);
-+
-+/* URB interface */
-+
-+/**
-+ * Allocates memory for dwc_otg_hcd_urb structure.
-+ * Allocated memory should be freed by call of DWC_FREE.
-+ *
-+ * @param hcd The HCD
-+ * @param iso_desc_count Count of ISOC descriptors
-+ * @param atomic_alloc Specefies whether to perform atomic allocation.
-+ */
-+extern dwc_otg_hcd_urb_t *dwc_otg_hcd_urb_alloc(dwc_otg_hcd_t * hcd,
-+ int iso_desc_count,
-+ int atomic_alloc);
-+
-+/**
-+ * Set pipe information in URB.
-+ *
-+ * @param hcd_urb DWC_OTG URB
-+ * @param devaddr Device Address
-+ * @param ep_num Endpoint Number
-+ * @param ep_type Endpoint Type
-+ * @param ep_dir Endpoint Direction
-+ * @param mps Max Packet Size
-+ */
-+extern void dwc_otg_hcd_urb_set_pipeinfo(dwc_otg_hcd_urb_t * hcd_urb,
-+ uint8_t devaddr, uint8_t ep_num,
-+ uint8_t ep_type, uint8_t ep_dir,
-+ uint16_t mps);
-+
-+/* Transfer flags */
-+#define URB_GIVEBACK_ASAP 0x1
-+#define URB_SEND_ZERO_PACKET 0x2
-+
-+/**
-+ * Sets dwc_otg_hcd_urb parameters.
-+ *
-+ * @param urb DWC_OTG URB allocated by dwc_otg_hcd_urb_alloc function.
-+ * @param urb_handle Unique handle for request, this will be passed back
-+ * to function driver in completion callback.
-+ * @param buf The buffer for the data
-+ * @param dma The DMA buffer for the data
-+ * @param buflen Transfer length
-+ * @param sp Buffer for setup data
-+ * @param sp_dma DMA address of setup data buffer
-+ * @param flags Transfer flags
-+ * @param interval Polling interval for interrupt or isochronous transfers.
-+ */
-+extern void dwc_otg_hcd_urb_set_params(dwc_otg_hcd_urb_t * urb,
-+ void *urb_handle, void *buf,
-+ dwc_dma_t dma, uint32_t buflen, void *sp,
-+ dwc_dma_t sp_dma, uint32_t flags,
-+ uint16_t interval);
-+
-+/** Gets status from dwc_otg_hcd_urb
-+ *
-+ * @param dwc_otg_urb DWC_OTG URB
-+ */
-+extern uint32_t dwc_otg_hcd_urb_get_status(dwc_otg_hcd_urb_t * dwc_otg_urb);
-+
-+/** Gets actual length from dwc_otg_hcd_urb
-+ *
-+ * @param dwc_otg_urb DWC_OTG URB
-+ */
-+extern uint32_t dwc_otg_hcd_urb_get_actual_length(dwc_otg_hcd_urb_t *
-+ dwc_otg_urb);
-+
-+/** Gets error count from dwc_otg_hcd_urb. Only for ISOC URBs
-+ *
-+ * @param dwc_otg_urb DWC_OTG URB
-+ */
-+extern uint32_t dwc_otg_hcd_urb_get_error_count(dwc_otg_hcd_urb_t *
-+ dwc_otg_urb);
-+
-+/** Set ISOC descriptor offset and length
-+ *
-+ * @param dwc_otg_urb DWC_OTG URB
-+ * @param desc_num ISOC descriptor number
-+ * @param offset Offset from beginig of buffer.
-+ * @param length Transaction length
-+ */
-+extern void dwc_otg_hcd_urb_set_iso_desc_params(dwc_otg_hcd_urb_t * dwc_otg_urb,
-+ int desc_num, uint32_t offset,
-+ uint32_t length);
-+
-+/** Get status of ISOC descriptor, specified by desc_num
-+ *
-+ * @param dwc_otg_urb DWC_OTG URB
-+ * @param desc_num ISOC descriptor number
-+ */
-+extern uint32_t dwc_otg_hcd_urb_get_iso_desc_status(dwc_otg_hcd_urb_t *
-+ dwc_otg_urb, int desc_num);
-+
-+/** Get actual length of ISOC descriptor, specified by desc_num
-+ *
-+ * @param dwc_otg_urb DWC_OTG URB
-+ * @param desc_num ISOC descriptor number
-+ */
-+extern uint32_t dwc_otg_hcd_urb_get_iso_desc_actual_length(dwc_otg_hcd_urb_t *
-+ dwc_otg_urb,
-+ int desc_num);
-+
-+/** Queue URB. After transfer is completes, the complete callback will be called with the URB status
-+ *
-+ * @param dwc_otg_hcd The HCD
-+ * @param dwc_otg_urb DWC_OTG URB
-+ * @param ep_handle Out parameter for returning endpoint handle
-+ * @param atomic_alloc Flag to do atomic allocation if needed
-+ *
-+ * Returns -DWC_E_NO_DEVICE if no device is connected.
-+ * Returns -DWC_E_NO_MEMORY if there is no enough memory.
-+ * Returns 0 on success.
-+ */
-+extern int dwc_otg_hcd_urb_enqueue(dwc_otg_hcd_t * dwc_otg_hcd,
-+ dwc_otg_hcd_urb_t * dwc_otg_urb,
-+ void **ep_handle, int atomic_alloc);
-+
-+/** De-queue the specified URB
-+ *
-+ * @param dwc_otg_hcd The HCD
-+ * @param dwc_otg_urb DWC_OTG URB
-+ */
-+extern int dwc_otg_hcd_urb_dequeue(dwc_otg_hcd_t * dwc_otg_hcd,
-+ dwc_otg_hcd_urb_t * dwc_otg_urb);
-+
-+/** Frees resources in the DWC_otg controller related to a given endpoint.
-+ * Any URBs for the endpoint must already be dequeued.
-+ *
-+ * @param hcd The HCD
-+ * @param ep_handle Endpoint handle, returned by dwc_otg_hcd_urb_enqueue function
-+ * @param retry Number of retries if there are queued transfers.
-+ *
-+ * Returns -DWC_E_INVALID if invalid arguments are passed.
-+ * Returns 0 on success
-+ */
-+extern int dwc_otg_hcd_endpoint_disable(dwc_otg_hcd_t * hcd, void *ep_handle,
-+ int retry);
-+
-+/* Resets the data toggle in qh structure. This function can be called from
-+ * usb_clear_halt routine.
-+ *
-+ * @param hcd The HCD
-+ * @param ep_handle Endpoint handle, returned by dwc_otg_hcd_urb_enqueue function
-+ *
-+ * Returns -DWC_E_INVALID if invalid arguments are passed.
-+ * Returns 0 on success
-+ */
-+extern int dwc_otg_hcd_endpoint_reset(dwc_otg_hcd_t * hcd, void *ep_handle);
-+
-+/** Returns 1 if status of specified port is changed and 0 otherwise.
-+ *
-+ * @param hcd The HCD
-+ * @param port Port number
-+ */
-+extern int dwc_otg_hcd_is_status_changed(dwc_otg_hcd_t * hcd, int port);
-+
-+/** Call this function to check if bandwidth was allocated for specified endpoint.
-+ * Only for ISOC and INTERRUPT endpoints.
-+ *
-+ * @param hcd The HCD
-+ * @param ep_handle Endpoint handle
-+ */
-+extern int dwc_otg_hcd_is_bandwidth_allocated(dwc_otg_hcd_t * hcd,
-+ void *ep_handle);
-+
-+/** Call this function to check if bandwidth was freed for specified endpoint.
-+ *
-+ * @param hcd The HCD
-+ * @param ep_handle Endpoint handle
-+ */
-+extern int dwc_otg_hcd_is_bandwidth_freed(dwc_otg_hcd_t * hcd, void *ep_handle);
-+
-+/** Returns bandwidth allocated for specified endpoint in microseconds.
-+ * Only for ISOC and INTERRUPT endpoints.
-+ *
-+ * @param hcd The HCD
-+ * @param ep_handle Endpoint handle
-+ */
-+extern uint8_t dwc_otg_hcd_get_ep_bandwidth(dwc_otg_hcd_t * hcd,
-+ void *ep_handle);
-+
-+/** @} */
-+
-+#endif /* __DWC_HCD_IF_H__ */
-+#endif /* DWC_DEVICE_ONLY */
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_hcd_intr.c
-@@ -0,0 +1,2714 @@
-+/* ==========================================================================
-+ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_hcd_intr.c $
-+ * $Revision: #89 $
-+ * $Date: 2011/10/20 $
-+ * $Change: 1869487 $
-+ *
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+#ifndef DWC_DEVICE_ONLY
-+
-+#include "dwc_otg_hcd.h"
-+#include "dwc_otg_regs.h"
-+
-+#include <linux/jiffies.h>
-+#include <asm/fiq.h>
-+
-+
-+extern bool microframe_schedule;
-+
-+/** @file
-+ * This file contains the implementation of the HCD Interrupt handlers.
-+ */
-+
-+int fiq_done, int_done;
-+
-+#ifdef FIQ_DEBUG
-+char buffer[1000*16];
-+int wptr;
-+void notrace _fiq_print(FIQDBG_T dbg_lvl, char *fmt, ...)
-+{
-+ FIQDBG_T dbg_lvl_req = FIQDBG_PORTHUB;
-+ va_list args;
-+ char text[17];
-+ hfnum_data_t hfnum = { .d32 = FIQ_READ(dwc_regs_base + 0x408) };
-+
-+ if(dbg_lvl & dbg_lvl_req || dbg_lvl == FIQDBG_ERR)
-+ {
-+ local_fiq_disable();
-+ snprintf(text, 9, "%4d%d:%d ", hfnum.b.frnum/8, hfnum.b.frnum%8, 8 - hfnum.b.frrem/937);
-+ va_start(args, fmt);
-+ vsnprintf(text+8, 9, fmt, args);
-+ va_end(args);
-+
-+ memcpy(buffer + wptr, text, 16);
-+ wptr = (wptr + 16) % sizeof(buffer);
-+ local_fiq_enable();
-+ }
-+}
-+#endif
-+
-+/** This function handles interrupts for the HCD. */
-+int32_t dwc_otg_hcd_handle_intr(dwc_otg_hcd_t * dwc_otg_hcd)
-+{
-+ int retval = 0;
-+ static int last_time;
-+ dwc_otg_core_if_t *core_if = dwc_otg_hcd->core_if;
-+ gintsts_data_t gintsts;
-+ gintmsk_data_t gintmsk;
-+ hfnum_data_t hfnum;
-+ haintmsk_data_t haintmsk;
-+
-+#ifdef DEBUG
-+ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs;
-+
-+#endif
-+
-+ gintsts.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintsts);
-+ gintmsk.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintmsk);
-+
-+ /* Exit from ISR if core is hibernated */
-+ if (core_if->hibernation_suspend == 1) {
-+ goto exit_handler_routine;
-+ }
-+ DWC_SPINLOCK(dwc_otg_hcd->lock);
-+ /* Check if HOST Mode */
-+ if (dwc_otg_is_host_mode(core_if)) {
-+ if (fiq_enable) {
-+ local_fiq_disable();
-+ fiq_fsm_spin_lock(&dwc_otg_hcd->fiq_state->lock);
-+ /* Pull in from the FIQ's disabled mask */
-+ gintmsk.d32 = gintmsk.d32 | ~(dwc_otg_hcd->fiq_state->gintmsk_saved.d32);
-+ dwc_otg_hcd->fiq_state->gintmsk_saved.d32 = ~0;
-+ }
-+
-+ if (fiq_fsm_enable && ( 0x0000FFFF & ~(dwc_otg_hcd->fiq_state->haintmsk_saved.b2.chint))) {
-+ gintsts.b.hcintr = 1;
-+ }
-+
-+ /* Danger will robinson: fake a SOF if necessary */
-+ if (fiq_fsm_enable && (dwc_otg_hcd->fiq_state->gintmsk_saved.b.sofintr == 1)) {
-+ gintsts.b.sofintr = 1;
-+ }
-+ gintsts.d32 &= gintmsk.d32;
-+
-+ if (fiq_enable) {
-+ fiq_fsm_spin_unlock(&dwc_otg_hcd->fiq_state->lock);
-+ local_fiq_enable();
-+ }
-+
-+ if (!gintsts.d32) {
-+ goto exit_handler_routine;
-+ }
-+
-+#ifdef DEBUG
-+ // We should be OK doing this because the common interrupts should already have been serviced
-+ /* Don't print debug message in the interrupt handler on SOF */
-+#ifndef DEBUG_SOF
-+ if (gintsts.d32 != DWC_SOF_INTR_MASK)
-+#endif
-+ DWC_DEBUGPL(DBG_HCDI, "\n");
-+#endif
-+
-+#ifdef DEBUG
-+#ifndef DEBUG_SOF
-+ if (gintsts.d32 != DWC_SOF_INTR_MASK)
-+#endif
-+ DWC_DEBUGPL(DBG_HCDI,
-+ "DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x%08x core_if=%p\n",
-+ gintsts.d32, core_if);
-+#endif
-+ hfnum.d32 = DWC_READ_REG32(&dwc_otg_hcd->core_if->host_if->host_global_regs->hfnum);
-+ if (gintsts.b.sofintr) {
-+ retval |= dwc_otg_hcd_handle_sof_intr(dwc_otg_hcd);
-+ }
-+
-+ if (gintsts.b.rxstsqlvl) {
-+ retval |=
-+ dwc_otg_hcd_handle_rx_status_q_level_intr
-+ (dwc_otg_hcd);
-+ }
-+ if (gintsts.b.nptxfempty) {
-+ retval |=
-+ dwc_otg_hcd_handle_np_tx_fifo_empty_intr
-+ (dwc_otg_hcd);
-+ }
-+ if (gintsts.b.i2cintr) {
-+ /** @todo Implement i2cintr handler. */
-+ }
-+ if (gintsts.b.portintr) {
-+
-+ gintmsk_data_t gintmsk = { .b.portintr = 1};
-+ retval |= dwc_otg_hcd_handle_port_intr(dwc_otg_hcd);
-+ if (fiq_enable) {
-+ local_fiq_disable();
-+ fiq_fsm_spin_lock(&dwc_otg_hcd->fiq_state->lock);
-+ DWC_MODIFY_REG32(&dwc_otg_hcd->core_if->core_global_regs->gintmsk, 0, gintmsk.d32);
-+ fiq_fsm_spin_unlock(&dwc_otg_hcd->fiq_state->lock);
-+ local_fiq_enable();
-+ } else {
-+ DWC_MODIFY_REG32(&dwc_otg_hcd->core_if->core_global_regs->gintmsk, 0, gintmsk.d32);
-+ }
-+ }
-+ if (gintsts.b.hcintr) {
-+ retval |= dwc_otg_hcd_handle_hc_intr(dwc_otg_hcd);
-+ }
-+ if (gintsts.b.ptxfempty) {
-+ retval |=
-+ dwc_otg_hcd_handle_perio_tx_fifo_empty_intr
-+ (dwc_otg_hcd);
-+ }
-+#ifdef DEBUG
-+#ifndef DEBUG_SOF
-+ if (gintsts.d32 != DWC_SOF_INTR_MASK)
-+#endif
-+ {
-+ DWC_DEBUGPL(DBG_HCDI,
-+ "DWC OTG HCD Finished Servicing Interrupts\n");
-+ DWC_DEBUGPL(DBG_HCDV, "DWC OTG HCD gintsts=0x%08x\n",
-+ DWC_READ_REG32(&global_regs->gintsts));
-+ DWC_DEBUGPL(DBG_HCDV, "DWC OTG HCD gintmsk=0x%08x\n",
-+ DWC_READ_REG32(&global_regs->gintmsk));
-+ }
-+#endif
-+
-+#ifdef DEBUG
-+#ifndef DEBUG_SOF
-+ if (gintsts.d32 != DWC_SOF_INTR_MASK)
-+#endif
-+ DWC_DEBUGPL(DBG_HCDI, "\n");
-+#endif
-+
-+ }
-+
-+exit_handler_routine:
-+ if (fiq_enable) {
-+ gintmsk_data_t gintmsk_new;
-+ haintmsk_data_t haintmsk_new;
-+ local_fiq_disable();
-+ fiq_fsm_spin_lock(&dwc_otg_hcd->fiq_state->lock);
-+ gintmsk_new.d32 = *(volatile uint32_t *)&dwc_otg_hcd->fiq_state->gintmsk_saved.d32;
-+ if(fiq_fsm_enable)
-+ haintmsk_new.d32 = *(volatile uint32_t *)&dwc_otg_hcd->fiq_state->haintmsk_saved.d32;
-+ else
-+ haintmsk_new.d32 = 0x0000FFFF;
-+
-+ /* The FIQ could have sneaked another interrupt in. If so, don't clear MPHI */
-+ if ((gintmsk_new.d32 == ~0) && (haintmsk_new.d32 == 0x0000FFFF)) {
-+ DWC_WRITE_REG32(dwc_otg_hcd->fiq_state->mphi_regs.intstat, (1<<16));
-+ if (dwc_otg_hcd->fiq_state->mphi_int_count >= 50) {
-+ fiq_print(FIQDBG_INT, dwc_otg_hcd->fiq_state, "MPHI CLR");
-+ DWC_WRITE_REG32(dwc_otg_hcd->fiq_state->mphi_regs.ctrl, ((1<<31) + (1<<16)));
-+ while (!(DWC_READ_REG32(dwc_otg_hcd->fiq_state->mphi_regs.ctrl) & (1 << 17)))
-+ ;
-+ DWC_WRITE_REG32(dwc_otg_hcd->fiq_state->mphi_regs.ctrl, (1<<31));
-+ dwc_otg_hcd->fiq_state->mphi_int_count = 0;
-+ }
-+ int_done++;
-+ }
-+ haintmsk.d32 = DWC_READ_REG32(&core_if->host_if->host_global_regs->haintmsk);
-+ /* Re-enable interrupts that the FIQ masked (first time round) */
-+ FIQ_WRITE(dwc_otg_hcd->fiq_state->dwc_regs_base + GINTMSK, gintmsk.d32);
-+ fiq_fsm_spin_unlock(&dwc_otg_hcd->fiq_state->lock);
-+ local_fiq_enable();
-+
-+ if ((jiffies / HZ) > last_time) {
-+ //dwc_otg_qh_t *qh;
-+ //dwc_list_link_t *cur;
-+ /* Once a second output the fiq and irq numbers, useful for debug */
-+ last_time = jiffies / HZ;
-+ // DWC_WARN("np_kick=%d AHC=%d sched_frame=%d cur_frame=%d int_done=%d fiq_done=%d",
-+ // dwc_otg_hcd->fiq_state->kick_np_queues, dwc_otg_hcd->available_host_channels,
-+ // dwc_otg_hcd->fiq_state->next_sched_frame, hfnum.b.frnum, int_done, dwc_otg_hcd->fiq_state->fiq_done);
-+ //printk(KERN_WARNING "Periodic queues:\n");
-+ }
-+ }
-+
-+ DWC_SPINUNLOCK(dwc_otg_hcd->lock);
-+ return retval;
-+}
-+
-+#ifdef DWC_TRACK_MISSED_SOFS
-+
-+#warning Compiling code to track missed SOFs
-+#define FRAME_NUM_ARRAY_SIZE 1000
-+/**
-+ * This function is for debug only.
-+ */
-+static inline void track_missed_sofs(uint16_t curr_frame_number)
-+{
-+ static uint16_t frame_num_array[FRAME_NUM_ARRAY_SIZE];
-+ static uint16_t last_frame_num_array[FRAME_NUM_ARRAY_SIZE];
-+ static int frame_num_idx = 0;
-+ static uint16_t last_frame_num = DWC_HFNUM_MAX_FRNUM;
-+ static int dumped_frame_num_array = 0;
-+
-+ if (frame_num_idx < FRAME_NUM_ARRAY_SIZE) {
-+ if (((last_frame_num + 1) & DWC_HFNUM_MAX_FRNUM) !=
-+ curr_frame_number) {
-+ frame_num_array[frame_num_idx] = curr_frame_number;
-+ last_frame_num_array[frame_num_idx++] = last_frame_num;
-+ }
-+ } else if (!dumped_frame_num_array) {
-+ int i;
-+ DWC_PRINTF("Frame Last Frame\n");
-+ DWC_PRINTF("----- ----------\n");
-+ for (i = 0; i < FRAME_NUM_ARRAY_SIZE; i++) {
-+ DWC_PRINTF("0x%04x 0x%04x\n",
-+ frame_num_array[i], last_frame_num_array[i]);
-+ }
-+ dumped_frame_num_array = 1;
-+ }
-+ last_frame_num = curr_frame_number;
-+}
-+#endif
-+
-+/**
-+ * Handles the start-of-frame interrupt in host mode. Non-periodic
-+ * transactions may be queued to the DWC_otg controller for the current
-+ * (micro)frame. Periodic transactions may be queued to the controller for the
-+ * next (micro)frame.
-+ */
-+int32_t dwc_otg_hcd_handle_sof_intr(dwc_otg_hcd_t * hcd)
-+{
-+ hfnum_data_t hfnum;
-+ gintsts_data_t gintsts = { .d32 = 0 };
-+ dwc_list_link_t *qh_entry;
-+ dwc_otg_qh_t *qh;
-+ dwc_otg_transaction_type_e tr_type;
-+ int did_something = 0;
-+ int32_t next_sched_frame = -1;
-+
-+ hfnum.d32 =
-+ DWC_READ_REG32(&hcd->core_if->host_if->host_global_regs->hfnum);
-+
-+#ifdef DEBUG_SOF
-+ DWC_DEBUGPL(DBG_HCD, "--Start of Frame Interrupt--\n");
-+#endif
-+ hcd->frame_number = hfnum.b.frnum;
-+
-+#ifdef DEBUG
-+ hcd->frrem_accum += hfnum.b.frrem;
-+ hcd->frrem_samples++;
-+#endif
-+
-+#ifdef DWC_TRACK_MISSED_SOFS
-+ track_missed_sofs(hcd->frame_number);
-+#endif
-+ /* Determine whether any periodic QHs should be executed. */
-+ qh_entry = DWC_LIST_FIRST(&hcd->periodic_sched_inactive);
-+ while (qh_entry != &hcd->periodic_sched_inactive) {
-+ qh = DWC_LIST_ENTRY(qh_entry, dwc_otg_qh_t, qh_list_entry);
-+ qh_entry = qh_entry->next;
-+ if (dwc_frame_num_le(qh->sched_frame, hcd->frame_number)) {
-+
-+ /*
-+ * Move QH to the ready list to be executed next
-+ * (micro)frame.
-+ */
-+ DWC_LIST_MOVE_HEAD(&hcd->periodic_sched_ready,
-+ &qh->qh_list_entry);
-+
-+ did_something = 1;
-+ }
-+ else
-+ {
-+ if(next_sched_frame < 0 || dwc_frame_num_le(qh->sched_frame, next_sched_frame))
-+ {
-+ next_sched_frame = qh->sched_frame;
-+ }
-+ }
-+ }
-+ if (fiq_enable)
-+ hcd->fiq_state->next_sched_frame = next_sched_frame;
-+
-+ tr_type = dwc_otg_hcd_select_transactions(hcd);
-+ if (tr_type != DWC_OTG_TRANSACTION_NONE) {
-+ dwc_otg_hcd_queue_transactions(hcd, tr_type);
-+ did_something = 1;
-+ }
-+
-+ /* Clear interrupt - but do not trample on the FIQ sof */
-+ if (!fiq_fsm_enable) {
-+ gintsts.b.sofintr = 1;
-+ DWC_WRITE_REG32(&hcd->core_if->core_global_regs->gintsts, gintsts.d32);
-+ }
-+ return 1;
-+}
-+
-+/** Handles the Rx Status Queue Level Interrupt, which indicates that there is at
-+ * least one packet in the Rx FIFO. The packets are moved from the FIFO to
-+ * memory if the DWC_otg controller is operating in Slave mode. */
-+int32_t dwc_otg_hcd_handle_rx_status_q_level_intr(dwc_otg_hcd_t * dwc_otg_hcd)
-+{
-+ host_grxsts_data_t grxsts;
-+ dwc_hc_t *hc = NULL;
-+
-+ DWC_DEBUGPL(DBG_HCD, "--RxStsQ Level Interrupt--\n");
-+
-+ grxsts.d32 =
-+ DWC_READ_REG32(&dwc_otg_hcd->core_if->core_global_regs->grxstsp);
-+
-+ hc = dwc_otg_hcd->hc_ptr_array[grxsts.b.chnum];
-+ if (!hc) {
-+ DWC_ERROR("Unable to get corresponding channel\n");
-+ return 0;
-+ }
-+
-+ /* Packet Status */
-+ DWC_DEBUGPL(DBG_HCDV, " Ch num = %d\n", grxsts.b.chnum);
-+ DWC_DEBUGPL(DBG_HCDV, " Count = %d\n", grxsts.b.bcnt);
-+ DWC_DEBUGPL(DBG_HCDV, " DPID = %d, hc.dpid = %d\n", grxsts.b.dpid,
-+ hc->data_pid_start);
-+ DWC_DEBUGPL(DBG_HCDV, " PStatus = %d\n", grxsts.b.pktsts);
-+
-+ switch (grxsts.b.pktsts) {
-+ case DWC_GRXSTS_PKTSTS_IN:
-+ /* Read the data into the host buffer. */
-+ if (grxsts.b.bcnt > 0) {
-+ dwc_otg_read_packet(dwc_otg_hcd->core_if,
-+ hc->xfer_buff, grxsts.b.bcnt);
-+
-+ /* Update the HC fields for the next packet received. */
-+ hc->xfer_count += grxsts.b.bcnt;
-+ hc->xfer_buff += grxsts.b.bcnt;
-+ }
-+
-+ case DWC_GRXSTS_PKTSTS_IN_XFER_COMP:
-+ case DWC_GRXSTS_PKTSTS_DATA_TOGGLE_ERR:
-+ case DWC_GRXSTS_PKTSTS_CH_HALTED:
-+ /* Handled in interrupt, just ignore data */
-+ break;
-+ default:
-+ DWC_ERROR("RX_STS_Q Interrupt: Unknown status %d\n",
-+ grxsts.b.pktsts);
-+ break;
-+ }
-+
-+ return 1;
-+}
-+
-+/** This interrupt occurs when the non-periodic Tx FIFO is half-empty. More
-+ * data packets may be written to the FIFO for OUT transfers. More requests
-+ * may be written to the non-periodic request queue for IN transfers. This
-+ * interrupt is enabled only in Slave mode. */
-+int32_t dwc_otg_hcd_handle_np_tx_fifo_empty_intr(dwc_otg_hcd_t * dwc_otg_hcd)
-+{
-+ DWC_DEBUGPL(DBG_HCD, "--Non-Periodic TxFIFO Empty Interrupt--\n");
-+ dwc_otg_hcd_queue_transactions(dwc_otg_hcd,
-+ DWC_OTG_TRANSACTION_NON_PERIODIC);
-+ return 1;
-+}
-+
-+/** This interrupt occurs when the periodic Tx FIFO is half-empty. More data
-+ * packets may be written to the FIFO for OUT transfers. More requests may be
-+ * written to the periodic request queue for IN transfers. This interrupt is
-+ * enabled only in Slave mode. */
-+int32_t dwc_otg_hcd_handle_perio_tx_fifo_empty_intr(dwc_otg_hcd_t * dwc_otg_hcd)
-+{
-+ DWC_DEBUGPL(DBG_HCD, "--Periodic TxFIFO Empty Interrupt--\n");
-+ dwc_otg_hcd_queue_transactions(dwc_otg_hcd,
-+ DWC_OTG_TRANSACTION_PERIODIC);
-+ return 1;
-+}
-+
-+/** There are multiple conditions that can cause a port interrupt. This function
-+ * determines which interrupt conditions have occurred and handles them
-+ * appropriately. */
-+int32_t dwc_otg_hcd_handle_port_intr(dwc_otg_hcd_t * dwc_otg_hcd)
-+{
-+ int retval = 0;
-+ hprt0_data_t hprt0;
-+ hprt0_data_t hprt0_modify;
-+
-+ hprt0.d32 = DWC_READ_REG32(dwc_otg_hcd->core_if->host_if->hprt0);
-+ hprt0_modify.d32 = DWC_READ_REG32(dwc_otg_hcd->core_if->host_if->hprt0);
-+
-+ /* Clear appropriate bits in HPRT0 to clear the interrupt bit in
-+ * GINTSTS */
-+
-+ hprt0_modify.b.prtena = 0;
-+ hprt0_modify.b.prtconndet = 0;
-+ hprt0_modify.b.prtenchng = 0;
-+ hprt0_modify.b.prtovrcurrchng = 0;
-+
-+ /* Port Connect Detected
-+ * Set flag and clear if detected */
-+ if (dwc_otg_hcd->core_if->hibernation_suspend == 1) {
-+ // Dont modify port status if we are in hibernation state
-+ hprt0_modify.b.prtconndet = 1;
-+ hprt0_modify.b.prtenchng = 1;
-+ DWC_WRITE_REG32(dwc_otg_hcd->core_if->host_if->hprt0, hprt0_modify.d32);
-+ hprt0.d32 = DWC_READ_REG32(dwc_otg_hcd->core_if->host_if->hprt0);
-+ return retval;
-+ }
-+
-+ if (hprt0.b.prtconndet) {
-+ /** @todo - check if steps performed in 'else' block should be perfromed regardles adp */
-+ if (dwc_otg_hcd->core_if->adp_enable &&
-+ dwc_otg_hcd->core_if->adp.vbuson_timer_started == 1) {
-+ DWC_PRINTF("PORT CONNECT DETECTED ----------------\n");
-+ DWC_TIMER_CANCEL(dwc_otg_hcd->core_if->adp.vbuson_timer);
-+ dwc_otg_hcd->core_if->adp.vbuson_timer_started = 0;
-+ /* TODO - check if this is required, as
-+ * host initialization was already performed
-+ * after initial ADP probing
-+ */
-+ /*dwc_otg_hcd->core_if->adp.vbuson_timer_started = 0;
-+ dwc_otg_core_init(dwc_otg_hcd->core_if);
-+ dwc_otg_enable_global_interrupts(dwc_otg_hcd->core_if);
-+ cil_hcd_start(dwc_otg_hcd->core_if);*/
-+ } else {
-+
-+ DWC_DEBUGPL(DBG_HCD, "--Port Interrupt HPRT0=0x%08x "
-+ "Port Connect Detected--\n", hprt0.d32);
-+ dwc_otg_hcd->flags.b.port_connect_status_change = 1;
-+ dwc_otg_hcd->flags.b.port_connect_status = 1;
-+ hprt0_modify.b.prtconndet = 1;
-+
-+ /* B-Device has connected, Delete the connection timer. */
-+ DWC_TIMER_CANCEL(dwc_otg_hcd->conn_timer);
-+ }
-+ /* The Hub driver asserts a reset when it sees port connect
-+ * status change flag */
-+ retval |= 1;
-+ }
-+
-+ /* Port Enable Changed
-+ * Clear if detected - Set internal flag if disabled */
-+ if (hprt0.b.prtenchng) {
-+ DWC_DEBUGPL(DBG_HCD, " --Port Interrupt HPRT0=0x%08x "
-+ "Port Enable Changed--\n", hprt0.d32);
-+ hprt0_modify.b.prtenchng = 1;
-+ if (hprt0.b.prtena == 1) {
-+ hfir_data_t hfir;
-+ int do_reset = 0;
-+ dwc_otg_core_params_t *params =
-+ dwc_otg_hcd->core_if->core_params;
-+ dwc_otg_core_global_regs_t *global_regs =
-+ dwc_otg_hcd->core_if->core_global_regs;
-+ dwc_otg_host_if_t *host_if =
-+ dwc_otg_hcd->core_if->host_if;
-+
-+ /* Every time when port enables calculate
-+ * HFIR.FrInterval
-+ */
-+ hfir.d32 = DWC_READ_REG32(&host_if->host_global_regs->hfir);
-+ hfir.b.frint = calc_frame_interval(dwc_otg_hcd->core_if);
-+ DWC_WRITE_REG32(&host_if->host_global_regs->hfir, hfir.d32);
-+
-+ /* Check if we need to adjust the PHY clock speed for
-+ * low power and adjust it */
-+ if (params->host_support_fs_ls_low_power) {
-+ gusbcfg_data_t usbcfg;
-+
-+ usbcfg.d32 =
-+ DWC_READ_REG32(&global_regs->gusbcfg);
-+
-+ if (hprt0.b.prtspd == DWC_HPRT0_PRTSPD_LOW_SPEED
-+ || hprt0.b.prtspd ==
-+ DWC_HPRT0_PRTSPD_FULL_SPEED) {
-+ /*
-+ * Low power
-+ */
-+ hcfg_data_t hcfg;
-+ if (usbcfg.b.phylpwrclksel == 0) {
-+ /* Set PHY low power clock select for FS/LS devices */
-+ usbcfg.b.phylpwrclksel = 1;
-+ DWC_WRITE_REG32
-+ (&global_regs->gusbcfg,
-+ usbcfg.d32);
-+ do_reset = 1;
-+ }
-+
-+ hcfg.d32 =
-+ DWC_READ_REG32
-+ (&host_if->host_global_regs->hcfg);
-+
-+ if (hprt0.b.prtspd ==
-+ DWC_HPRT0_PRTSPD_LOW_SPEED
-+ && params->host_ls_low_power_phy_clk
-+ ==
-+ DWC_HOST_LS_LOW_POWER_PHY_CLK_PARAM_6MHZ)
-+ {
-+ /* 6 MHZ */
-+ DWC_DEBUGPL(DBG_CIL,
-+ "FS_PHY programming HCFG to 6 MHz (Low Power)\n");
-+ if (hcfg.b.fslspclksel !=
-+ DWC_HCFG_6_MHZ) {
-+ hcfg.b.fslspclksel =
-+ DWC_HCFG_6_MHZ;
-+ DWC_WRITE_REG32
-+ (&host_if->host_global_regs->hcfg,
-+ hcfg.d32);
-+ do_reset = 1;
-+ }
-+ } else {
-+ /* 48 MHZ */
-+ DWC_DEBUGPL(DBG_CIL,
-+ "FS_PHY programming HCFG to 48 MHz ()\n");
-+ if (hcfg.b.fslspclksel !=
-+ DWC_HCFG_48_MHZ) {
-+ hcfg.b.fslspclksel =
-+ DWC_HCFG_48_MHZ;
-+ DWC_WRITE_REG32
-+ (&host_if->host_global_regs->hcfg,
-+ hcfg.d32);
-+ do_reset = 1;
-+ }
-+ }
-+ } else {
-+ /*
-+ * Not low power
-+ */
-+ if (usbcfg.b.phylpwrclksel == 1) {
-+ usbcfg.b.phylpwrclksel = 0;
-+ DWC_WRITE_REG32
-+ (&global_regs->gusbcfg,
-+ usbcfg.d32);
-+ do_reset = 1;
-+ }
-+ }
-+
-+ if (do_reset) {
-+ DWC_TASK_SCHEDULE(dwc_otg_hcd->reset_tasklet);
-+ }
-+ }
-+
-+ if (!do_reset) {
-+ /* Port has been enabled set the reset change flag */
-+ dwc_otg_hcd->flags.b.port_reset_change = 1;
-+ }
-+ } else {
-+ dwc_otg_hcd->flags.b.port_enable_change = 1;
-+ }
-+ retval |= 1;
-+ }
-+
-+ /** Overcurrent Change Interrupt */
-+ if (hprt0.b.prtovrcurrchng) {
-+ DWC_DEBUGPL(DBG_HCD, " --Port Interrupt HPRT0=0x%08x "
-+ "Port Overcurrent Changed--\n", hprt0.d32);
-+ dwc_otg_hcd->flags.b.port_over_current_change = 1;
-+ hprt0_modify.b.prtovrcurrchng = 1;
-+ retval |= 1;
-+ }
-+
-+ /* Clear Port Interrupts */
-+ DWC_WRITE_REG32(dwc_otg_hcd->core_if->host_if->hprt0, hprt0_modify.d32);
-+
-+ return retval;
-+}
-+
-+/** This interrupt indicates that one or more host channels has a pending
-+ * interrupt. There are multiple conditions that can cause each host channel
-+ * interrupt. This function determines which conditions have occurred for each
-+ * host channel interrupt and handles them appropriately. */
-+int32_t dwc_otg_hcd_handle_hc_intr(dwc_otg_hcd_t * dwc_otg_hcd)
-+{
-+ int i;
-+ int retval = 0;
-+ haint_data_t haint = { .d32 = 0 } ;
-+
-+ /* Clear appropriate bits in HCINTn to clear the interrupt bit in
-+ * GINTSTS */
-+
-+ if (!fiq_fsm_enable)
-+ haint.d32 = dwc_otg_read_host_all_channels_intr(dwc_otg_hcd->core_if);
-+
-+ // Overwrite with saved interrupts from fiq handler
-+ if(fiq_fsm_enable)
-+ {
-+ /* check the mask? */
-+ local_fiq_disable();
-+ fiq_fsm_spin_lock(&dwc_otg_hcd->fiq_state->lock);
-+ haint.b2.chint |= ~(dwc_otg_hcd->fiq_state->haintmsk_saved.b2.chint);
-+ dwc_otg_hcd->fiq_state->haintmsk_saved.b2.chint = ~0;
-+ fiq_fsm_spin_unlock(&dwc_otg_hcd->fiq_state->lock);
-+ local_fiq_enable();
-+ }
-+
-+ for (i = 0; i < dwc_otg_hcd->core_if->core_params->host_channels; i++) {
-+ if (haint.b2.chint & (1 << i)) {
-+ retval |= dwc_otg_hcd_handle_hc_n_intr(dwc_otg_hcd, i);
-+ }
-+ }
-+
-+ return retval;
-+}
-+
-+/**
-+ * Gets the actual length of a transfer after the transfer halts. _halt_status
-+ * holds the reason for the halt.
-+ *
-+ * For IN transfers where halt_status is DWC_OTG_HC_XFER_COMPLETE,
-+ * *short_read is set to 1 upon return if less than the requested
-+ * number of bytes were transferred. Otherwise, *short_read is set to 0 upon
-+ * return. short_read may also be NULL on entry, in which case it remains
-+ * unchanged.
-+ */
-+static uint32_t get_actual_xfer_length(dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs,
-+ dwc_otg_qtd_t * qtd,
-+ dwc_otg_halt_status_e halt_status,
-+ int *short_read)
-+{
-+ hctsiz_data_t hctsiz;
-+ uint32_t length;
-+
-+ if (short_read != NULL) {
-+ *short_read = 0;
-+ }
-+ hctsiz.d32 = DWC_READ_REG32(&hc_regs->hctsiz);
-+
-+ if (halt_status == DWC_OTG_HC_XFER_COMPLETE) {
-+ if (hc->ep_is_in) {
-+ length = hc->xfer_len - hctsiz.b.xfersize;
-+ if (short_read != NULL) {
-+ *short_read = (hctsiz.b.xfersize != 0);
-+ }
-+ } else if (hc->qh->do_split) {
-+ //length = split_out_xfersize[hc->hc_num];
-+ length = qtd->ssplit_out_xfer_count;
-+ } else {
-+ length = hc->xfer_len;
-+ }
-+ } else {
-+ /*
-+ * Must use the hctsiz.pktcnt field to determine how much data
-+ * has been transferred. This field reflects the number of
-+ * packets that have been transferred via the USB. This is
-+ * always an integral number of packets if the transfer was
-+ * halted before its normal completion. (Can't use the
-+ * hctsiz.xfersize field because that reflects the number of
-+ * bytes transferred via the AHB, not the USB).
-+ */
-+ length =
-+ (hc->start_pkt_count - hctsiz.b.pktcnt) * hc->max_packet;
-+ }
-+
-+ return length;
-+}
-+
-+/**
-+ * Updates the state of the URB after a Transfer Complete interrupt on the
-+ * host channel. Updates the actual_length field of the URB based on the
-+ * number of bytes transferred via the host channel. Sets the URB status
-+ * if the data transfer is finished.
-+ *
-+ * @return 1 if the data transfer specified by the URB is completely finished,
-+ * 0 otherwise.
-+ */
-+static int update_urb_state_xfer_comp(dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs,
-+ dwc_otg_hcd_urb_t * urb,
-+ dwc_otg_qtd_t * qtd)
-+{
-+ int xfer_done = 0;
-+ int short_read = 0;
-+
-+ int xfer_length;
-+
-+ xfer_length = get_actual_xfer_length(hc, hc_regs, qtd,
-+ DWC_OTG_HC_XFER_COMPLETE,
-+ &short_read);
-+
-+ /* non DWORD-aligned buffer case handling. */
-+ if (hc->align_buff && xfer_length && hc->ep_is_in) {
-+ dwc_memcpy(urb->buf + urb->actual_length, hc->qh->dw_align_buf,
-+ xfer_length);
-+ }
-+
-+ urb->actual_length += xfer_length;
-+
-+ if (xfer_length && (hc->ep_type == DWC_OTG_EP_TYPE_BULK) &&
-+ (urb->flags & URB_SEND_ZERO_PACKET)
-+ && (urb->actual_length == urb->length)
-+ && !(urb->length % hc->max_packet)) {
-+ xfer_done = 0;
-+ } else if (short_read || urb->actual_length >= urb->length) {
-+ xfer_done = 1;
-+ urb->status = 0;
-+ }
-+
-+#ifdef DEBUG
-+ {
-+ hctsiz_data_t hctsiz;
-+ hctsiz.d32 = DWC_READ_REG32(&hc_regs->hctsiz);
-+ DWC_DEBUGPL(DBG_HCDV, "DWC_otg: %s: %s, channel %d\n",
-+ __func__, (hc->ep_is_in ? "IN" : "OUT"),
-+ hc->hc_num);
-+ DWC_DEBUGPL(DBG_HCDV, " hc->xfer_len %d\n", hc->xfer_len);
-+ DWC_DEBUGPL(DBG_HCDV, " hctsiz.xfersize %d\n",
-+ hctsiz.b.xfersize);
-+ DWC_DEBUGPL(DBG_HCDV, " urb->transfer_buffer_length %d\n",
-+ urb->length);
-+ DWC_DEBUGPL(DBG_HCDV, " urb->actual_length %d\n",
-+ urb->actual_length);
-+ DWC_DEBUGPL(DBG_HCDV, " short_read %d, xfer_done %d\n",
-+ short_read, xfer_done);
-+ }
-+#endif
-+
-+ return xfer_done;
-+}
-+
-+/*
-+ * Save the starting data toggle for the next transfer. The data toggle is
-+ * saved in the QH for non-control transfers and it's saved in the QTD for
-+ * control transfers.
-+ */
-+void dwc_otg_hcd_save_data_toggle(dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs, dwc_otg_qtd_t * qtd)
-+{
-+ hctsiz_data_t hctsiz;
-+ hctsiz.d32 = DWC_READ_REG32(&hc_regs->hctsiz);
-+
-+ if (hc->ep_type != DWC_OTG_EP_TYPE_CONTROL) {
-+ dwc_otg_qh_t *qh = hc->qh;
-+ if (hctsiz.b.pid == DWC_HCTSIZ_DATA0) {
-+ qh->data_toggle = DWC_OTG_HC_PID_DATA0;
-+ } else {
-+ qh->data_toggle = DWC_OTG_HC_PID_DATA1;
-+ }
-+ } else {
-+ if (hctsiz.b.pid == DWC_HCTSIZ_DATA0) {
-+ qtd->data_toggle = DWC_OTG_HC_PID_DATA0;
-+ } else {
-+ qtd->data_toggle = DWC_OTG_HC_PID_DATA1;
-+ }
-+ }
-+}
-+
-+/**
-+ * Updates the state of an Isochronous URB when the transfer is stopped for
-+ * any reason. The fields of the current entry in the frame descriptor array
-+ * are set based on the transfer state and the input _halt_status. Completes
-+ * the Isochronous URB if all the URB frames have been completed.
-+ *
-+ * @return DWC_OTG_HC_XFER_COMPLETE if there are more frames remaining to be
-+ * transferred in the URB. Otherwise return DWC_OTG_HC_XFER_URB_COMPLETE.
-+ */
-+static dwc_otg_halt_status_e
-+update_isoc_urb_state(dwc_otg_hcd_t * hcd,
-+ dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs,
-+ dwc_otg_qtd_t * qtd, dwc_otg_halt_status_e halt_status)
-+{
-+ dwc_otg_hcd_urb_t *urb = qtd->urb;
-+ dwc_otg_halt_status_e ret_val = halt_status;
-+ struct dwc_otg_hcd_iso_packet_desc *frame_desc;
-+
-+ frame_desc = &urb->iso_descs[qtd->isoc_frame_index];
-+ switch (halt_status) {
-+ case DWC_OTG_HC_XFER_COMPLETE:
-+ frame_desc->status = 0;
-+ frame_desc->actual_length =
-+ get_actual_xfer_length(hc, hc_regs, qtd, halt_status, NULL);
-+
-+ /* non DWORD-aligned buffer case handling. */
-+ if (hc->align_buff && frame_desc->actual_length && hc->ep_is_in) {
-+ dwc_memcpy(urb->buf + frame_desc->offset + qtd->isoc_split_offset,
-+ hc->qh->dw_align_buf, frame_desc->actual_length);
-+ }
-+
-+ break;
-+ case DWC_OTG_HC_XFER_FRAME_OVERRUN:
-+ urb->error_count++;
-+ if (hc->ep_is_in) {
-+ frame_desc->status = -DWC_E_NO_STREAM_RES;
-+ } else {
-+ frame_desc->status = -DWC_E_COMMUNICATION;
-+ }
-+ frame_desc->actual_length = 0;
-+ break;
-+ case DWC_OTG_HC_XFER_BABBLE_ERR:
-+ urb->error_count++;
-+ frame_desc->status = -DWC_E_OVERFLOW;
-+ /* Don't need to update actual_length in this case. */
-+ break;
-+ case DWC_OTG_HC_XFER_XACT_ERR:
-+ urb->error_count++;
-+ frame_desc->status = -DWC_E_PROTOCOL;
-+ frame_desc->actual_length =
-+ get_actual_xfer_length(hc, hc_regs, qtd, halt_status, NULL);
-+
-+ /* non DWORD-aligned buffer case handling. */
-+ if (hc->align_buff && frame_desc->actual_length && hc->ep_is_in) {
-+ dwc_memcpy(urb->buf + frame_desc->offset + qtd->isoc_split_offset,
-+ hc->qh->dw_align_buf, frame_desc->actual_length);
-+ }
-+ /* Skip whole frame */
-+ if (hc->qh->do_split && (hc->ep_type == DWC_OTG_EP_TYPE_ISOC) &&
-+ hc->ep_is_in && hcd->core_if->dma_enable) {
-+ qtd->complete_split = 0;
-+ qtd->isoc_split_offset = 0;
-+ }
-+
-+ break;
-+ default:
-+ DWC_ASSERT(1, "Unhandled _halt_status (%d)\n", halt_status);
-+ break;
-+ }
-+ if (++qtd->isoc_frame_index == urb->packet_count) {
-+ /*
-+ * urb->status is not used for isoc transfers.
-+ * The individual frame_desc statuses are used instead.
-+ */
-+ hcd->fops->complete(hcd, urb->priv, urb, 0);
-+ ret_val = DWC_OTG_HC_XFER_URB_COMPLETE;
-+ } else {
-+ ret_val = DWC_OTG_HC_XFER_COMPLETE;
-+ }
-+ return ret_val;
-+}
-+
-+/**
-+ * Frees the first QTD in the QH's list if free_qtd is 1. For non-periodic
-+ * QHs, removes the QH from the active non-periodic schedule. If any QTDs are
-+ * still linked to the QH, the QH is added to the end of the inactive
-+ * non-periodic schedule. For periodic QHs, removes the QH from the periodic
-+ * schedule if no more QTDs are linked to the QH.
-+ */
-+static void deactivate_qh(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh, int free_qtd)
-+{
-+ int continue_split = 0;
-+ dwc_otg_qtd_t *qtd;
-+
-+ DWC_DEBUGPL(DBG_HCDV, " %s(%p,%p,%d)\n", __func__, hcd, qh, free_qtd);
-+
-+ qtd = DWC_CIRCLEQ_FIRST(&qh->qtd_list);
-+
-+ if (qtd->complete_split) {
-+ continue_split = 1;
-+ } else if (qtd->isoc_split_pos == DWC_HCSPLIT_XACTPOS_MID ||
-+ qtd->isoc_split_pos == DWC_HCSPLIT_XACTPOS_END) {
-+ continue_split = 1;
-+ }
-+
-+ if (free_qtd) {
-+ dwc_otg_hcd_qtd_remove_and_free(hcd, qtd, qh);
-+ continue_split = 0;
-+ }
-+
-+ qh->channel = NULL;
-+ dwc_otg_hcd_qh_deactivate(hcd, qh, continue_split);
-+}
-+
-+/**
-+ * Releases a host channel for use by other transfers. Attempts to select and
-+ * queue more transactions since at least one host channel is available.
-+ *
-+ * @param hcd The HCD state structure.
-+ * @param hc The host channel to release.
-+ * @param qtd The QTD associated with the host channel. This QTD may be freed
-+ * if the transfer is complete or an error has occurred.
-+ * @param halt_status Reason the channel is being released. This status
-+ * determines the actions taken by this function.
-+ */
-+static void release_channel(dwc_otg_hcd_t * hcd,
-+ dwc_hc_t * hc,
-+ dwc_otg_qtd_t * qtd,
-+ dwc_otg_halt_status_e halt_status)
-+{
-+ dwc_otg_transaction_type_e tr_type;
-+ int free_qtd;
-+ dwc_irqflags_t flags;
-+ dwc_spinlock_t *channel_lock = hcd->channel_lock;
-+
-+ int hog_port = 0;
-+
-+ DWC_DEBUGPL(DBG_HCDV, " %s: channel %d, halt_status %d, xfer_len %d\n",
-+ __func__, hc->hc_num, halt_status, hc->xfer_len);
-+
-+ if(fiq_fsm_enable && hc->do_split) {
-+ if(!hc->ep_is_in && hc->ep_type == UE_ISOCHRONOUS) {
-+ if(hc->xact_pos == DWC_HCSPLIT_XACTPOS_MID ||
-+ hc->xact_pos == DWC_HCSPLIT_XACTPOS_BEGIN) {
-+ hog_port = 0;
-+ }
-+ }
-+ }
-+
-+ switch (halt_status) {
-+ case DWC_OTG_HC_XFER_URB_COMPLETE:
-+ free_qtd = 1;
-+ break;
-+ case DWC_OTG_HC_XFER_AHB_ERR:
-+ case DWC_OTG_HC_XFER_STALL:
-+ case DWC_OTG_HC_XFER_BABBLE_ERR:
-+ free_qtd = 1;
-+ break;
-+ case DWC_OTG_HC_XFER_XACT_ERR:
-+ if (qtd->error_count >= 3) {
-+ DWC_DEBUGPL(DBG_HCDV,
-+ " Complete URB with transaction error\n");
-+ free_qtd = 1;
-+ qtd->urb->status = -DWC_E_PROTOCOL;
-+ hcd->fops->complete(hcd, qtd->urb->priv,
-+ qtd->urb, -DWC_E_PROTOCOL);
-+ } else {
-+ free_qtd = 0;
-+ }
-+ break;
-+ case DWC_OTG_HC_XFER_URB_DEQUEUE:
-+ /*
-+ * The QTD has already been removed and the QH has been
-+ * deactivated. Don't want to do anything except release the
-+ * host channel and try to queue more transfers.
-+ */
-+ goto cleanup;
-+ case DWC_OTG_HC_XFER_NO_HALT_STATUS:
-+ free_qtd = 0;
-+ break;
-+ case DWC_OTG_HC_XFER_PERIODIC_INCOMPLETE:
-+ DWC_DEBUGPL(DBG_HCDV,
-+ " Complete URB with I/O error\n");
-+ free_qtd = 1;
-+ qtd->urb->status = -DWC_E_IO;
-+ hcd->fops->complete(hcd, qtd->urb->priv,
-+ qtd->urb, -DWC_E_IO);
-+ break;
-+ default:
-+ free_qtd = 0;
-+ break;
-+ }
-+
-+ deactivate_qh(hcd, hc->qh, free_qtd);
-+
-+cleanup:
-+ /*
-+ * Release the host channel for use by other transfers. The cleanup
-+ * function clears the channel interrupt enables and conditions, so
-+ * there's no need to clear the Channel Halted interrupt separately.
-+ */
-+ if (fiq_fsm_enable && hcd->fiq_state->channel[hc->hc_num].fsm != FIQ_PASSTHROUGH)
-+ dwc_otg_cleanup_fiq_channel(hcd, hc->hc_num);
-+ dwc_otg_hc_cleanup(hcd->core_if, hc);
-+ DWC_CIRCLEQ_INSERT_TAIL(&hcd->free_hc_list, hc, hc_list_entry);
-+
-+ if (!microframe_schedule) {
-+ switch (hc->ep_type) {
-+ case DWC_OTG_EP_TYPE_CONTROL:
-+ case DWC_OTG_EP_TYPE_BULK:
-+ hcd->non_periodic_channels--;
-+ break;
-+
-+ default:
-+ /*
-+ * Don't release reservations for periodic channels here.
-+ * That's done when a periodic transfer is descheduled (i.e.
-+ * when the QH is removed from the periodic schedule).
-+ */
-+ break;
-+ }
-+ } else {
-+
-+ DWC_SPINLOCK_IRQSAVE(channel_lock, &flags);
-+ hcd->available_host_channels++;
-+ fiq_print(FIQDBG_INT, hcd->fiq_state, "AHC = %d ", hcd->available_host_channels);
-+ DWC_SPINUNLOCK_IRQRESTORE(channel_lock, flags);
-+ }
-+
-+ /* Try to queue more transfers now that there's a free channel. */
-+ tr_type = dwc_otg_hcd_select_transactions(hcd);
-+ if (tr_type != DWC_OTG_TRANSACTION_NONE) {
-+ dwc_otg_hcd_queue_transactions(hcd, tr_type);
-+ }
-+}
-+
-+/**
-+ * Halts a host channel. If the channel cannot be halted immediately because
-+ * the request queue is full, this function ensures that the FIFO empty
-+ * interrupt for the appropriate queue is enabled so that the halt request can
-+ * be queued when there is space in the request queue.
-+ *
-+ * This function may also be called in DMA mode. In that case, the channel is
-+ * simply released since the core always halts the channel automatically in
-+ * DMA mode.
-+ */
-+static void halt_channel(dwc_otg_hcd_t * hcd,
-+ dwc_hc_t * hc,
-+ dwc_otg_qtd_t * qtd, dwc_otg_halt_status_e halt_status)
-+{
-+ if (hcd->core_if->dma_enable) {
-+ release_channel(hcd, hc, qtd, halt_status);
-+ return;
-+ }
-+
-+ /* Slave mode processing... */
-+ dwc_otg_hc_halt(hcd->core_if, hc, halt_status);
-+
-+ if (hc->halt_on_queue) {
-+ gintmsk_data_t gintmsk = {.d32 = 0 };
-+ dwc_otg_core_global_regs_t *global_regs;
-+ global_regs = hcd->core_if->core_global_regs;
-+
-+ if (hc->ep_type == DWC_OTG_EP_TYPE_CONTROL ||
-+ hc->ep_type == DWC_OTG_EP_TYPE_BULK) {
-+ /*
-+ * Make sure the Non-periodic Tx FIFO empty interrupt
-+ * is enabled so that the non-periodic schedule will
-+ * be processed.
-+ */
-+ gintmsk.b.nptxfempty = 1;
-+ if (fiq_enable) {
-+ local_fiq_disable();
-+ fiq_fsm_spin_lock(&hcd->fiq_state->lock);
-+ DWC_MODIFY_REG32(&global_regs->gintmsk, 0, gintmsk.d32);
-+ fiq_fsm_spin_unlock(&hcd->fiq_state->lock);
-+ local_fiq_enable();
-+ } else {
-+ DWC_MODIFY_REG32(&global_regs->gintmsk, 0, gintmsk.d32);
-+ }
-+ } else {
-+ /*
-+ * Move the QH from the periodic queued schedule to
-+ * the periodic assigned schedule. This allows the
-+ * halt to be queued when the periodic schedule is
-+ * processed.
-+ */
-+ DWC_LIST_MOVE_HEAD(&hcd->periodic_sched_assigned,
-+ &hc->qh->qh_list_entry);
-+
-+ /*
-+ * Make sure the Periodic Tx FIFO Empty interrupt is
-+ * enabled so that the periodic schedule will be
-+ * processed.
-+ */
-+ gintmsk.b.ptxfempty = 1;
-+ if (fiq_enable) {
-+ local_fiq_disable();
-+ fiq_fsm_spin_lock(&hcd->fiq_state->lock);
-+ DWC_MODIFY_REG32(&global_regs->gintmsk, 0, gintmsk.d32);
-+ fiq_fsm_spin_unlock(&hcd->fiq_state->lock);
-+ local_fiq_enable();
-+ } else {
-+ DWC_MODIFY_REG32(&global_regs->gintmsk, 0, gintmsk.d32);
-+ }
-+ }
-+ }
-+}
-+
-+/**
-+ * Performs common cleanup for non-periodic transfers after a Transfer
-+ * Complete interrupt. This function should be called after any endpoint type
-+ * specific handling is finished to release the host channel.
-+ */
-+static void complete_non_periodic_xfer(dwc_otg_hcd_t * hcd,
-+ dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs,
-+ dwc_otg_qtd_t * qtd,
-+ dwc_otg_halt_status_e halt_status)
-+{
-+ hcint_data_t hcint;
-+
-+ qtd->error_count = 0;
-+
-+ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint);
-+ if (hcint.b.nyet) {
-+ /*
-+ * Got a NYET on the last transaction of the transfer. This
-+ * means that the endpoint should be in the PING state at the
-+ * beginning of the next transfer.
-+ */
-+ hc->qh->ping_state = 1;
-+ clear_hc_int(hc_regs, nyet);
-+ }
-+
-+ /*
-+ * Always halt and release the host channel to make it available for
-+ * more transfers. There may still be more phases for a control
-+ * transfer or more data packets for a bulk transfer at this point,
-+ * but the host channel is still halted. A channel will be reassigned
-+ * to the transfer when the non-periodic schedule is processed after
-+ * the channel is released. This allows transactions to be queued
-+ * properly via dwc_otg_hcd_queue_transactions, which also enables the
-+ * Tx FIFO Empty interrupt if necessary.
-+ */
-+ if (hc->ep_is_in) {
-+ /*
-+ * IN transfers in Slave mode require an explicit disable to
-+ * halt the channel. (In DMA mode, this call simply releases
-+ * the channel.)
-+ */
-+ halt_channel(hcd, hc, qtd, halt_status);
-+ } else {
-+ /*
-+ * The channel is automatically disabled by the core for OUT
-+ * transfers in Slave mode.
-+ */
-+ release_channel(hcd, hc, qtd, halt_status);
-+ }
-+}
-+
-+/**
-+ * Performs common cleanup for periodic transfers after a Transfer Complete
-+ * interrupt. This function should be called after any endpoint type specific
-+ * handling is finished to release the host channel.
-+ */
-+static void complete_periodic_xfer(dwc_otg_hcd_t * hcd,
-+ dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs,
-+ dwc_otg_qtd_t * qtd,
-+ dwc_otg_halt_status_e halt_status)
-+{
-+ hctsiz_data_t hctsiz;
-+ qtd->error_count = 0;
-+
-+ hctsiz.d32 = DWC_READ_REG32(&hc_regs->hctsiz);
-+ if (!hc->ep_is_in || hctsiz.b.pktcnt == 0) {
-+ /* Core halts channel in these cases. */
-+ release_channel(hcd, hc, qtd, halt_status);
-+ } else {
-+ /* Flush any outstanding requests from the Tx queue. */
-+ halt_channel(hcd, hc, qtd, halt_status);
-+ }
-+}
-+
-+static int32_t handle_xfercomp_isoc_split_in(dwc_otg_hcd_t * hcd,
-+ dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs,
-+ dwc_otg_qtd_t * qtd)
-+{
-+ uint32_t len;
-+ struct dwc_otg_hcd_iso_packet_desc *frame_desc;
-+ frame_desc = &qtd->urb->iso_descs[qtd->isoc_frame_index];
-+
-+ len = get_actual_xfer_length(hc, hc_regs, qtd,
-+ DWC_OTG_HC_XFER_COMPLETE, NULL);
-+
-+ if (!len) {
-+ qtd->complete_split = 0;
-+ qtd->isoc_split_offset = 0;
-+ return 0;
-+ }
-+ frame_desc->actual_length += len;
-+
-+ if (hc->align_buff && len)
-+ dwc_memcpy(qtd->urb->buf + frame_desc->offset +
-+ qtd->isoc_split_offset, hc->qh->dw_align_buf, len);
-+ qtd->isoc_split_offset += len;
-+
-+ if (frame_desc->length == frame_desc->actual_length) {
-+ frame_desc->status = 0;
-+ qtd->isoc_frame_index++;
-+ qtd->complete_split = 0;
-+ qtd->isoc_split_offset = 0;
-+ }
-+
-+ if (qtd->isoc_frame_index == qtd->urb->packet_count) {
-+ hcd->fops->complete(hcd, qtd->urb->priv, qtd->urb, 0);
-+ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_URB_COMPLETE);
-+ } else {
-+ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NO_HALT_STATUS);
-+ }
-+
-+ return 1; /* Indicates that channel released */
-+}
-+
-+/**
-+ * Handles a host channel Transfer Complete interrupt. This handler may be
-+ * called in either DMA mode or Slave mode.
-+ */
-+static int32_t handle_hc_xfercomp_intr(dwc_otg_hcd_t * hcd,
-+ dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs,
-+ dwc_otg_qtd_t * qtd)
-+{
-+ int urb_xfer_done;
-+ dwc_otg_halt_status_e halt_status = DWC_OTG_HC_XFER_COMPLETE;
-+ dwc_otg_hcd_urb_t *urb = qtd->urb;
-+ int pipe_type = dwc_otg_hcd_get_pipe_type(&urb->pipe_info);
-+
-+ DWC_DEBUGPL(DBG_HCDI, "--Host Channel %d Interrupt: "
-+ "Transfer Complete--\n", hc->hc_num);
-+
-+ if (hcd->core_if->dma_desc_enable) {
-+ dwc_otg_hcd_complete_xfer_ddma(hcd, hc, hc_regs, halt_status);
-+ if (pipe_type == UE_ISOCHRONOUS) {
-+ /* Do not disable the interrupt, just clear it */
-+ clear_hc_int(hc_regs, xfercomp);
-+ return 1;
-+ }
-+ goto handle_xfercomp_done;
-+ }
-+
-+ /*
-+ * Handle xfer complete on CSPLIT.
-+ */
-+
-+ if (hc->qh->do_split) {
-+ if ((hc->ep_type == DWC_OTG_EP_TYPE_ISOC) && hc->ep_is_in
-+ && hcd->core_if->dma_enable) {
-+ if (qtd->complete_split
-+ && handle_xfercomp_isoc_split_in(hcd, hc, hc_regs,
-+ qtd))
-+ goto handle_xfercomp_done;
-+ } else {
-+ qtd->complete_split = 0;
-+ }
-+ }
-+
-+ /* Update the QTD and URB states. */
-+ switch (pipe_type) {
-+ case UE_CONTROL:
-+ switch (qtd->control_phase) {
-+ case DWC_OTG_CONTROL_SETUP:
-+ if (urb->length > 0) {
-+ qtd->control_phase = DWC_OTG_CONTROL_DATA;
-+ } else {
-+ qtd->control_phase = DWC_OTG_CONTROL_STATUS;
-+ }
-+ DWC_DEBUGPL(DBG_HCDV,
-+ " Control setup transaction done\n");
-+ halt_status = DWC_OTG_HC_XFER_COMPLETE;
-+ break;
-+ case DWC_OTG_CONTROL_DATA:{
-+ urb_xfer_done =
-+ update_urb_state_xfer_comp(hc, hc_regs, urb,
-+ qtd);
-+ if (urb_xfer_done) {
-+ qtd->control_phase =
-+ DWC_OTG_CONTROL_STATUS;
-+ DWC_DEBUGPL(DBG_HCDV,
-+ " Control data transfer done\n");
-+ } else {
-+ dwc_otg_hcd_save_data_toggle(hc, hc_regs, qtd);
-+ }
-+ halt_status = DWC_OTG_HC_XFER_COMPLETE;
-+ break;
-+ }
-+ case DWC_OTG_CONTROL_STATUS:
-+ DWC_DEBUGPL(DBG_HCDV, " Control transfer complete\n");
-+ if (urb->status == -DWC_E_IN_PROGRESS) {
-+ urb->status = 0;
-+ }
-+ hcd->fops->complete(hcd, urb->priv, urb, urb->status);
-+ halt_status = DWC_OTG_HC_XFER_URB_COMPLETE;
-+ break;
-+ }
-+
-+ complete_non_periodic_xfer(hcd, hc, hc_regs, qtd, halt_status);
-+ break;
-+ case UE_BULK:
-+ DWC_DEBUGPL(DBG_HCDV, " Bulk transfer complete\n");
-+ urb_xfer_done =
-+ update_urb_state_xfer_comp(hc, hc_regs, urb, qtd);
-+ if (urb_xfer_done) {
-+ hcd->fops->complete(hcd, urb->priv, urb, urb->status);
-+ halt_status = DWC_OTG_HC_XFER_URB_COMPLETE;
-+ } else {
-+ halt_status = DWC_OTG_HC_XFER_COMPLETE;
-+ }
-+
-+ dwc_otg_hcd_save_data_toggle(hc, hc_regs, qtd);
-+ complete_non_periodic_xfer(hcd, hc, hc_regs, qtd, halt_status);
-+ break;
-+ case UE_INTERRUPT:
-+ DWC_DEBUGPL(DBG_HCDV, " Interrupt transfer complete\n");
-+ urb_xfer_done =
-+ update_urb_state_xfer_comp(hc, hc_regs, urb, qtd);
-+
-+ /*
-+ * Interrupt URB is done on the first transfer complete
-+ * interrupt.
-+ */
-+ if (urb_xfer_done) {
-+ hcd->fops->complete(hcd, urb->priv, urb, urb->status);
-+ halt_status = DWC_OTG_HC_XFER_URB_COMPLETE;
-+ } else {
-+ halt_status = DWC_OTG_HC_XFER_COMPLETE;
-+ }
-+
-+ dwc_otg_hcd_save_data_toggle(hc, hc_regs, qtd);
-+ complete_periodic_xfer(hcd, hc, hc_regs, qtd, halt_status);
-+ break;
-+ case UE_ISOCHRONOUS:
-+ DWC_DEBUGPL(DBG_HCDV, " Isochronous transfer complete\n");
-+ if (qtd->isoc_split_pos == DWC_HCSPLIT_XACTPOS_ALL) {
-+ halt_status =
-+ update_isoc_urb_state(hcd, hc, hc_regs, qtd,
-+ DWC_OTG_HC_XFER_COMPLETE);
-+ }
-+ complete_periodic_xfer(hcd, hc, hc_regs, qtd, halt_status);
-+ break;
-+ }
-+
-+handle_xfercomp_done:
-+ disable_hc_int(hc_regs, xfercompl);
-+
-+ return 1;
-+}
-+
-+/**
-+ * Handles a host channel STALL interrupt. This handler may be called in
-+ * either DMA mode or Slave mode.
-+ */
-+static int32_t handle_hc_stall_intr(dwc_otg_hcd_t * hcd,
-+ dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs,
-+ dwc_otg_qtd_t * qtd)
-+{
-+ dwc_otg_hcd_urb_t *urb = qtd->urb;
-+ int pipe_type = dwc_otg_hcd_get_pipe_type(&urb->pipe_info);
-+
-+ DWC_DEBUGPL(DBG_HCD, "--Host Channel %d Interrupt: "
-+ "STALL Received--\n", hc->hc_num);
-+
-+ if (hcd->core_if->dma_desc_enable) {
-+ dwc_otg_hcd_complete_xfer_ddma(hcd, hc, hc_regs, DWC_OTG_HC_XFER_STALL);
-+ goto handle_stall_done;
-+ }
-+
-+ if (pipe_type == UE_CONTROL) {
-+ hcd->fops->complete(hcd, urb->priv, urb, -DWC_E_PIPE);
-+ }
-+
-+ if (pipe_type == UE_BULK || pipe_type == UE_INTERRUPT) {
-+ hcd->fops->complete(hcd, urb->priv, urb, -DWC_E_PIPE);
-+ /*
-+ * USB protocol requires resetting the data toggle for bulk
-+ * and interrupt endpoints when a CLEAR_FEATURE(ENDPOINT_HALT)
-+ * setup command is issued to the endpoint. Anticipate the
-+ * CLEAR_FEATURE command since a STALL has occurred and reset
-+ * the data toggle now.
-+ */
-+ hc->qh->data_toggle = 0;
-+ }
-+
-+ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_STALL);
-+
-+handle_stall_done:
-+ disable_hc_int(hc_regs, stall);
-+
-+ return 1;
-+}
-+
-+/*
-+ * Updates the state of the URB when a transfer has been stopped due to an
-+ * abnormal condition before the transfer completes. Modifies the
-+ * actual_length field of the URB to reflect the number of bytes that have
-+ * actually been transferred via the host channel.
-+ */
-+static void update_urb_state_xfer_intr(dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs,
-+ dwc_otg_hcd_urb_t * urb,
-+ dwc_otg_qtd_t * qtd,
-+ dwc_otg_halt_status_e halt_status)
-+{
-+ uint32_t bytes_transferred = get_actual_xfer_length(hc, hc_regs, qtd,
-+ halt_status, NULL);
-+ /* non DWORD-aligned buffer case handling. */
-+ if (hc->align_buff && bytes_transferred && hc->ep_is_in) {
-+ dwc_memcpy(urb->buf + urb->actual_length, hc->qh->dw_align_buf,
-+ bytes_transferred);
-+ }
-+
-+ urb->actual_length += bytes_transferred;
-+
-+#ifdef DEBUG
-+ {
-+ hctsiz_data_t hctsiz;
-+ hctsiz.d32 = DWC_READ_REG32(&hc_regs->hctsiz);
-+ DWC_DEBUGPL(DBG_HCDV, "DWC_otg: %s: %s, channel %d\n",
-+ __func__, (hc->ep_is_in ? "IN" : "OUT"),
-+ hc->hc_num);
-+ DWC_DEBUGPL(DBG_HCDV, " hc->start_pkt_count %d\n",
-+ hc->start_pkt_count);
-+ DWC_DEBUGPL(DBG_HCDV, " hctsiz.pktcnt %d\n", hctsiz.b.pktcnt);
-+ DWC_DEBUGPL(DBG_HCDV, " hc->max_packet %d\n", hc->max_packet);
-+ DWC_DEBUGPL(DBG_HCDV, " bytes_transferred %d\n",
-+ bytes_transferred);
-+ DWC_DEBUGPL(DBG_HCDV, " urb->actual_length %d\n",
-+ urb->actual_length);
-+ DWC_DEBUGPL(DBG_HCDV, " urb->transfer_buffer_length %d\n",
-+ urb->length);
-+ }
-+#endif
-+}
-+
-+/**
-+ * Handles a host channel NAK interrupt. This handler may be called in either
-+ * DMA mode or Slave mode.
-+ */
-+static int32_t handle_hc_nak_intr(dwc_otg_hcd_t * hcd,
-+ dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs,
-+ dwc_otg_qtd_t * qtd)
-+{
-+ DWC_DEBUGPL(DBG_HCDI, "--Host Channel %d Interrupt: "
-+ "NAK Received--\n", hc->hc_num);
-+
-+ /*
-+ * When we get bulk NAKs then remember this so we holdoff on this qh until
-+ * the beginning of the next frame
-+ */
-+ switch(dwc_otg_hcd_get_pipe_type(&qtd->urb->pipe_info)) {
-+ case UE_BULK:
-+ case UE_CONTROL:
-+ if (nak_holdoff && qtd->qh->do_split)
-+ hc->qh->nak_frame = dwc_otg_hcd_get_frame_number(hcd);
-+ }
-+
-+ /*
-+ * Handle NAK for IN/OUT SSPLIT/CSPLIT transfers, bulk, control, and
-+ * interrupt. Re-start the SSPLIT transfer.
-+ */
-+ if (hc->do_split) {
-+ if (hc->complete_split) {
-+ qtd->error_count = 0;
-+ }
-+ qtd->complete_split = 0;
-+ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NAK);
-+ goto handle_nak_done;
-+ }
-+
-+ switch (dwc_otg_hcd_get_pipe_type(&qtd->urb->pipe_info)) {
-+ case UE_CONTROL:
-+ case UE_BULK:
-+ if (hcd->core_if->dma_enable && hc->ep_is_in) {
-+ /*
-+ * NAK interrupts are enabled on bulk/control IN
-+ * transfers in DMA mode for the sole purpose of
-+ * resetting the error count after a transaction error
-+ * occurs. The core will continue transferring data.
-+ * Disable other interrupts unmasked for the same
-+ * reason.
-+ */
-+ disable_hc_int(hc_regs, datatglerr);
-+ disable_hc_int(hc_regs, ack);
-+ qtd->error_count = 0;
-+ goto handle_nak_done;
-+ }
-+
-+ /*
-+ * NAK interrupts normally occur during OUT transfers in DMA
-+ * or Slave mode. For IN transfers, more requests will be
-+ * queued as request queue space is available.
-+ */
-+ qtd->error_count = 0;
-+
-+ if (!hc->qh->ping_state) {
-+ update_urb_state_xfer_intr(hc, hc_regs,
-+ qtd->urb, qtd,
-+ DWC_OTG_HC_XFER_NAK);
-+ dwc_otg_hcd_save_data_toggle(hc, hc_regs, qtd);
-+
-+ if (hc->speed == DWC_OTG_EP_SPEED_HIGH)
-+ hc->qh->ping_state = 1;
-+ }
-+
-+ /*
-+ * Halt the channel so the transfer can be re-started from
-+ * the appropriate point or the PING protocol will
-+ * start/continue.
-+ */
-+ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NAK);
-+ break;
-+ case UE_INTERRUPT:
-+ qtd->error_count = 0;
-+ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NAK);
-+ break;
-+ case UE_ISOCHRONOUS:
-+ /* Should never get called for isochronous transfers. */
-+ DWC_ASSERT(1, "NACK interrupt for ISOC transfer\n");
-+ break;
-+ }
-+
-+handle_nak_done:
-+ disable_hc_int(hc_regs, nak);
-+
-+ return 1;
-+}
-+
-+/**
-+ * Handles a host channel ACK interrupt. This interrupt is enabled when
-+ * performing the PING protocol in Slave mode, when errors occur during
-+ * either Slave mode or DMA mode, and during Start Split transactions.
-+ */
-+static int32_t handle_hc_ack_intr(dwc_otg_hcd_t * hcd,
-+ dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs,
-+ dwc_otg_qtd_t * qtd)
-+{
-+ DWC_DEBUGPL(DBG_HCDI, "--Host Channel %d Interrupt: "
-+ "ACK Received--\n", hc->hc_num);
-+
-+ if (hc->do_split) {
-+ /*
-+ * Handle ACK on SSPLIT.
-+ * ACK should not occur in CSPLIT.
-+ */
-+ if (!hc->ep_is_in && hc->data_pid_start != DWC_OTG_HC_PID_SETUP) {
-+ qtd->ssplit_out_xfer_count = hc->xfer_len;
-+ }
-+ if (!(hc->ep_type == DWC_OTG_EP_TYPE_ISOC && !hc->ep_is_in)) {
-+ /* Don't need complete for isochronous out transfers. */
-+ qtd->complete_split = 1;
-+ }
-+
-+ /* ISOC OUT */
-+ if (hc->ep_type == DWC_OTG_EP_TYPE_ISOC && !hc->ep_is_in) {
-+ switch (hc->xact_pos) {
-+ case DWC_HCSPLIT_XACTPOS_ALL:
-+ break;
-+ case DWC_HCSPLIT_XACTPOS_END:
-+ qtd->isoc_split_pos = DWC_HCSPLIT_XACTPOS_ALL;
-+ qtd->isoc_split_offset = 0;
-+ break;
-+ case DWC_HCSPLIT_XACTPOS_BEGIN:
-+ case DWC_HCSPLIT_XACTPOS_MID:
-+ /*
-+ * For BEGIN or MID, calculate the length for
-+ * the next microframe to determine the correct
-+ * SSPLIT token, either MID or END.
-+ */
-+ {
-+ struct dwc_otg_hcd_iso_packet_desc
-+ *frame_desc;
-+
-+ frame_desc =
-+ &qtd->urb->
-+ iso_descs[qtd->isoc_frame_index];
-+ qtd->isoc_split_offset += 188;
-+
-+ if ((frame_desc->length -
-+ qtd->isoc_split_offset) <= 188) {
-+ qtd->isoc_split_pos =
-+ DWC_HCSPLIT_XACTPOS_END;
-+ } else {
-+ qtd->isoc_split_pos =
-+ DWC_HCSPLIT_XACTPOS_MID;
-+ }
-+
-+ }
-+ break;
-+ }
-+ } else {
-+ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_ACK);
-+ }
-+ } else {
-+ /*
-+ * An unmasked ACK on a non-split DMA transaction is
-+ * for the sole purpose of resetting error counts. Disable other
-+ * interrupts unmasked for the same reason.
-+ */
-+ if(hcd->core_if->dma_enable) {
-+ disable_hc_int(hc_regs, datatglerr);
-+ disable_hc_int(hc_regs, nak);
-+ }
-+ qtd->error_count = 0;
-+
-+ if (hc->qh->ping_state) {
-+ hc->qh->ping_state = 0;
-+ /*
-+ * Halt the channel so the transfer can be re-started
-+ * from the appropriate point. This only happens in
-+ * Slave mode. In DMA mode, the ping_state is cleared
-+ * when the transfer is started because the core
-+ * automatically executes the PING, then the transfer.
-+ */
-+ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_ACK);
-+ }
-+ }
-+
-+ /*
-+ * If the ACK occurred when _not_ in the PING state, let the channel
-+ * continue transferring data after clearing the error count.
-+ */
-+
-+ disable_hc_int(hc_regs, ack);
-+
-+ return 1;
-+}
-+
-+/**
-+ * Handles a host channel NYET interrupt. This interrupt should only occur on
-+ * Bulk and Control OUT endpoints and for complete split transactions. If a
-+ * NYET occurs at the same time as a Transfer Complete interrupt, it is
-+ * handled in the xfercomp interrupt handler, not here. This handler may be
-+ * called in either DMA mode or Slave mode.
-+ */
-+static int32_t handle_hc_nyet_intr(dwc_otg_hcd_t * hcd,
-+ dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs,
-+ dwc_otg_qtd_t * qtd)
-+{
-+ DWC_DEBUGPL(DBG_HCDI, "--Host Channel %d Interrupt: "
-+ "NYET Received--\n", hc->hc_num);
-+
-+ /*
-+ * NYET on CSPLIT
-+ * re-do the CSPLIT immediately on non-periodic
-+ */
-+ if (hc->do_split && hc->complete_split) {
-+ if (hc->ep_is_in && (hc->ep_type == DWC_OTG_EP_TYPE_ISOC)
-+ && hcd->core_if->dma_enable) {
-+ qtd->complete_split = 0;
-+ qtd->isoc_split_offset = 0;
-+ if (++qtd->isoc_frame_index == qtd->urb->packet_count) {
-+ hcd->fops->complete(hcd, qtd->urb->priv, qtd->urb, 0);
-+ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_URB_COMPLETE);
-+ }
-+ else
-+ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NO_HALT_STATUS);
-+ goto handle_nyet_done;
-+ }
-+
-+ if (hc->ep_type == DWC_OTG_EP_TYPE_INTR ||
-+ hc->ep_type == DWC_OTG_EP_TYPE_ISOC) {
-+ int frnum = dwc_otg_hcd_get_frame_number(hcd);
-+
-+ // With the FIQ running we only ever see the failed NYET
-+ if (dwc_full_frame_num(frnum) !=
-+ dwc_full_frame_num(hc->qh->sched_frame) ||
-+ fiq_fsm_enable) {
-+ /*
-+ * No longer in the same full speed frame.
-+ * Treat this as a transaction error.
-+ */
-+#if 0
-+ /** @todo Fix system performance so this can
-+ * be treated as an error. Right now complete
-+ * splits cannot be scheduled precisely enough
-+ * due to other system activity, so this error
-+ * occurs regularly in Slave mode.
-+ */
-+ qtd->error_count++;
-+#endif
-+ qtd->complete_split = 0;
-+ halt_channel(hcd, hc, qtd,
-+ DWC_OTG_HC_XFER_XACT_ERR);
-+ /** @todo add support for isoc release */
-+ goto handle_nyet_done;
-+ }
-+ }
-+
-+ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NYET);
-+ goto handle_nyet_done;
-+ }
-+
-+ hc->qh->ping_state = 1;
-+ qtd->error_count = 0;
-+
-+ update_urb_state_xfer_intr(hc, hc_regs, qtd->urb, qtd,
-+ DWC_OTG_HC_XFER_NYET);
-+ dwc_otg_hcd_save_data_toggle(hc, hc_regs, qtd);
-+
-+ /*
-+ * Halt the channel and re-start the transfer so the PING
-+ * protocol will start.
-+ */
-+ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NYET);
-+
-+handle_nyet_done:
-+ disable_hc_int(hc_regs, nyet);
-+ return 1;
-+}
-+
-+/**
-+ * Handles a host channel babble interrupt. This handler may be called in
-+ * either DMA mode or Slave mode.
-+ */
-+static int32_t handle_hc_babble_intr(dwc_otg_hcd_t * hcd,
-+ dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs,
-+ dwc_otg_qtd_t * qtd)
-+{
-+ DWC_DEBUGPL(DBG_HCDI, "--Host Channel %d Interrupt: "
-+ "Babble Error--\n", hc->hc_num);
-+
-+ if (hcd->core_if->dma_desc_enable) {
-+ dwc_otg_hcd_complete_xfer_ddma(hcd, hc, hc_regs,
-+ DWC_OTG_HC_XFER_BABBLE_ERR);
-+ goto handle_babble_done;
-+ }
-+
-+ if (hc->ep_type != DWC_OTG_EP_TYPE_ISOC) {
-+ hcd->fops->complete(hcd, qtd->urb->priv,
-+ qtd->urb, -DWC_E_OVERFLOW);
-+ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_BABBLE_ERR);
-+ } else {
-+ dwc_otg_halt_status_e halt_status;
-+ halt_status = update_isoc_urb_state(hcd, hc, hc_regs, qtd,
-+ DWC_OTG_HC_XFER_BABBLE_ERR);
-+ halt_channel(hcd, hc, qtd, halt_status);
-+ }
-+
-+handle_babble_done:
-+ disable_hc_int(hc_regs, bblerr);
-+ return 1;
-+}
-+
-+/**
-+ * Handles a host channel AHB error interrupt. This handler is only called in
-+ * DMA mode.
-+ */
-+static int32_t handle_hc_ahberr_intr(dwc_otg_hcd_t * hcd,
-+ dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs,
-+ dwc_otg_qtd_t * qtd)
-+{
-+ hcchar_data_t hcchar;
-+ hcsplt_data_t hcsplt;
-+ hctsiz_data_t hctsiz;
-+ uint32_t hcdma;
-+ char *pipetype, *speed;
-+
-+ dwc_otg_hcd_urb_t *urb = qtd->urb;
-+
-+ DWC_DEBUGPL(DBG_HCDI, "--Host Channel %d Interrupt: "
-+ "AHB Error--\n", hc->hc_num);
-+
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+ hcsplt.d32 = DWC_READ_REG32(&hc_regs->hcsplt);
-+ hctsiz.d32 = DWC_READ_REG32(&hc_regs->hctsiz);
-+ hcdma = DWC_READ_REG32(&hc_regs->hcdma);
-+
-+ DWC_ERROR("AHB ERROR, Channel %d\n", hc->hc_num);
-+ DWC_ERROR(" hcchar 0x%08x, hcsplt 0x%08x\n", hcchar.d32, hcsplt.d32);
-+ DWC_ERROR(" hctsiz 0x%08x, hcdma 0x%08x\n", hctsiz.d32, hcdma);
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD URB Enqueue\n");
-+ DWC_ERROR(" Device address: %d\n",
-+ dwc_otg_hcd_get_dev_addr(&urb->pipe_info));
-+ DWC_ERROR(" Endpoint: %d, %s\n",
-+ dwc_otg_hcd_get_ep_num(&urb->pipe_info),
-+ (dwc_otg_hcd_is_pipe_in(&urb->pipe_info) ? "IN" : "OUT"));
-+
-+ switch (dwc_otg_hcd_get_pipe_type(&urb->pipe_info)) {
-+ case UE_CONTROL:
-+ pipetype = "CONTROL";
-+ break;
-+ case UE_BULK:
-+ pipetype = "BULK";
-+ break;
-+ case UE_INTERRUPT:
-+ pipetype = "INTERRUPT";
-+ break;
-+ case UE_ISOCHRONOUS:
-+ pipetype = "ISOCHRONOUS";
-+ break;
-+ default:
-+ pipetype = "UNKNOWN";
-+ break;
-+ }
-+
-+ DWC_ERROR(" Endpoint type: %s\n", pipetype);
-+
-+ switch (hc->speed) {
-+ case DWC_OTG_EP_SPEED_HIGH:
-+ speed = "HIGH";
-+ break;
-+ case DWC_OTG_EP_SPEED_FULL:
-+ speed = "FULL";
-+ break;
-+ case DWC_OTG_EP_SPEED_LOW:
-+ speed = "LOW";
-+ break;
-+ default:
-+ speed = "UNKNOWN";
-+ break;
-+ };
-+
-+ DWC_ERROR(" Speed: %s\n", speed);
-+
-+ DWC_ERROR(" Max packet size: %d\n",
-+ dwc_otg_hcd_get_mps(&urb->pipe_info));
-+ DWC_ERROR(" Data buffer length: %d\n", urb->length);
-+ DWC_ERROR(" Transfer buffer: %p, Transfer DMA: %p\n",
-+ urb->buf, (void *)urb->dma);
-+ DWC_ERROR(" Setup buffer: %p, Setup DMA: %p\n",
-+ urb->setup_packet, (void *)urb->setup_dma);
-+ DWC_ERROR(" Interval: %d\n", urb->interval);
-+
-+ /* Core haltes the channel for Descriptor DMA mode */
-+ if (hcd->core_if->dma_desc_enable) {
-+ dwc_otg_hcd_complete_xfer_ddma(hcd, hc, hc_regs,
-+ DWC_OTG_HC_XFER_AHB_ERR);
-+ goto handle_ahberr_done;
-+ }
-+
-+ hcd->fops->complete(hcd, urb->priv, urb, -DWC_E_IO);
-+
-+ /*
-+ * Force a channel halt. Don't call halt_channel because that won't
-+ * write to the HCCHARn register in DMA mode to force the halt.
-+ */
-+ dwc_otg_hc_halt(hcd->core_if, hc, DWC_OTG_HC_XFER_AHB_ERR);
-+handle_ahberr_done:
-+ disable_hc_int(hc_regs, ahberr);
-+ return 1;
-+}
-+
-+/**
-+ * Handles a host channel transaction error interrupt. This handler may be
-+ * called in either DMA mode or Slave mode.
-+ */
-+static int32_t handle_hc_xacterr_intr(dwc_otg_hcd_t * hcd,
-+ dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs,
-+ dwc_otg_qtd_t * qtd)
-+{
-+ DWC_DEBUGPL(DBG_HCDI, "--Host Channel %d Interrupt: "
-+ "Transaction Error--\n", hc->hc_num);
-+
-+ if (hcd->core_if->dma_desc_enable) {
-+ dwc_otg_hcd_complete_xfer_ddma(hcd, hc, hc_regs,
-+ DWC_OTG_HC_XFER_XACT_ERR);
-+ goto handle_xacterr_done;
-+ }
-+
-+ switch (dwc_otg_hcd_get_pipe_type(&qtd->urb->pipe_info)) {
-+ case UE_CONTROL:
-+ case UE_BULK:
-+ qtd->error_count++;
-+ if (!hc->qh->ping_state) {
-+
-+ update_urb_state_xfer_intr(hc, hc_regs,
-+ qtd->urb, qtd,
-+ DWC_OTG_HC_XFER_XACT_ERR);
-+ dwc_otg_hcd_save_data_toggle(hc, hc_regs, qtd);
-+ if (!hc->ep_is_in && hc->speed == DWC_OTG_EP_SPEED_HIGH) {
-+ hc->qh->ping_state = 1;
-+ }
-+ }
-+
-+ /*
-+ * Halt the channel so the transfer can be re-started from
-+ * the appropriate point or the PING protocol will start.
-+ */
-+ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_XACT_ERR);
-+ break;
-+ case UE_INTERRUPT:
-+ qtd->error_count++;
-+ if (hc->do_split && hc->complete_split) {
-+ qtd->complete_split = 0;
-+ }
-+ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_XACT_ERR);
-+ break;
-+ case UE_ISOCHRONOUS:
-+ {
-+ dwc_otg_halt_status_e halt_status;
-+ halt_status =
-+ update_isoc_urb_state(hcd, hc, hc_regs, qtd,
-+ DWC_OTG_HC_XFER_XACT_ERR);
-+
-+ halt_channel(hcd, hc, qtd, halt_status);
-+ }
-+ break;
-+ }
-+handle_xacterr_done:
-+ disable_hc_int(hc_regs, xacterr);
-+
-+ return 1;
-+}
-+
-+/**
-+ * Handles a host channel frame overrun interrupt. This handler may be called
-+ * in either DMA mode or Slave mode.
-+ */
-+static int32_t handle_hc_frmovrun_intr(dwc_otg_hcd_t * hcd,
-+ dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs,
-+ dwc_otg_qtd_t * qtd)
-+{
-+ DWC_DEBUGPL(DBG_HCDI, "--Host Channel %d Interrupt: "
-+ "Frame Overrun--\n", hc->hc_num);
-+
-+ switch (dwc_otg_hcd_get_pipe_type(&qtd->urb->pipe_info)) {
-+ case UE_CONTROL:
-+ case UE_BULK:
-+ break;
-+ case UE_INTERRUPT:
-+ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_FRAME_OVERRUN);
-+ break;
-+ case UE_ISOCHRONOUS:
-+ {
-+ dwc_otg_halt_status_e halt_status;
-+ halt_status =
-+ update_isoc_urb_state(hcd, hc, hc_regs, qtd,
-+ DWC_OTG_HC_XFER_FRAME_OVERRUN);
-+
-+ halt_channel(hcd, hc, qtd, halt_status);
-+ }
-+ break;
-+ }
-+
-+ disable_hc_int(hc_regs, frmovrun);
-+
-+ return 1;
-+}
-+
-+/**
-+ * Handles a host channel data toggle error interrupt. This handler may be
-+ * called in either DMA mode or Slave mode.
-+ */
-+static int32_t handle_hc_datatglerr_intr(dwc_otg_hcd_t * hcd,
-+ dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs,
-+ dwc_otg_qtd_t * qtd)
-+{
-+ DWC_DEBUGPL(DBG_HCDI, "--Host Channel %d Interrupt: "
-+ "Data Toggle Error on %s transfer--\n",
-+ hc->hc_num, (hc->ep_is_in ? "IN" : "OUT"));
-+
-+ /* Data toggles on split transactions cause the hc to halt.
-+ * restart transfer */
-+ if(hc->qh->do_split)
-+ {
-+ qtd->error_count++;
-+ dwc_otg_hcd_save_data_toggle(hc, hc_regs, qtd);
-+ update_urb_state_xfer_intr(hc, hc_regs,
-+ qtd->urb, qtd, DWC_OTG_HC_XFER_XACT_ERR);
-+ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_XACT_ERR);
-+ } else if (hc->ep_is_in) {
-+ /* An unmasked data toggle error on a non-split DMA transaction is
-+ * for the sole purpose of resetting error counts. Disable other
-+ * interrupts unmasked for the same reason.
-+ */
-+ if(hcd->core_if->dma_enable) {
-+ disable_hc_int(hc_regs, ack);
-+ disable_hc_int(hc_regs, nak);
-+ }
-+ qtd->error_count = 0;
-+ }
-+
-+ disable_hc_int(hc_regs, datatglerr);
-+
-+ return 1;
-+}
-+
-+#ifdef DEBUG
-+/**
-+ * This function is for debug only. It checks that a valid halt status is set
-+ * and that HCCHARn.chdis is clear. If there's a problem, corrective action is
-+ * taken and a warning is issued.
-+ * @return 1 if halt status is ok, 0 otherwise.
-+ */
-+static inline int halt_status_ok(dwc_otg_hcd_t * hcd,
-+ dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs,
-+ dwc_otg_qtd_t * qtd)
-+{
-+ hcchar_data_t hcchar;
-+ hctsiz_data_t hctsiz;
-+ hcint_data_t hcint;
-+ hcintmsk_data_t hcintmsk;
-+ hcsplt_data_t hcsplt;
-+
-+ if (hc->halt_status == DWC_OTG_HC_XFER_NO_HALT_STATUS) {
-+ /*
-+ * This code is here only as a check. This condition should
-+ * never happen. Ignore the halt if it does occur.
-+ */
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+ hctsiz.d32 = DWC_READ_REG32(&hc_regs->hctsiz);
-+ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint);
-+ hcintmsk.d32 = DWC_READ_REG32(&hc_regs->hcintmsk);
-+ hcsplt.d32 = DWC_READ_REG32(&hc_regs->hcsplt);
-+ DWC_WARN
-+ ("%s: hc->halt_status == DWC_OTG_HC_XFER_NO_HALT_STATUS, "
-+ "channel %d, hcchar 0x%08x, hctsiz 0x%08x, "
-+ "hcint 0x%08x, hcintmsk 0x%08x, "
-+ "hcsplt 0x%08x, qtd->complete_split %d\n", __func__,
-+ hc->hc_num, hcchar.d32, hctsiz.d32, hcint.d32,
-+ hcintmsk.d32, hcsplt.d32, qtd->complete_split);
-+
-+ DWC_WARN("%s: no halt status, channel %d, ignoring interrupt\n",
-+ __func__, hc->hc_num);
-+ DWC_WARN("\n");
-+ clear_hc_int(hc_regs, chhltd);
-+ return 0;
-+ }
-+
-+ /*
-+ * This code is here only as a check. hcchar.chdis should
-+ * never be set when the halt interrupt occurs. Halt the
-+ * channel again if it does occur.
-+ */
-+ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar);
-+ if (hcchar.b.chdis) {
-+ DWC_WARN("%s: hcchar.chdis set unexpectedly, "
-+ "hcchar 0x%08x, trying to halt again\n",
-+ __func__, hcchar.d32);
-+ clear_hc_int(hc_regs, chhltd);
-+ hc->halt_pending = 0;
-+ halt_channel(hcd, hc, qtd, hc->halt_status);
-+ return 0;
-+ }
-+
-+ return 1;
-+}
-+#endif
-+
-+/**
-+ * Handles a host Channel Halted interrupt in DMA mode. This handler
-+ * determines the reason the channel halted and proceeds accordingly.
-+ */
-+static void handle_hc_chhltd_intr_dma(dwc_otg_hcd_t * hcd,
-+ dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs,
-+ dwc_otg_qtd_t * qtd)
-+{
-+ int out_nak_enh = 0;
-+ hcint_data_t hcint;
-+ hcintmsk_data_t hcintmsk;
-+ /* For core with OUT NAK enhancement, the flow for high-
-+ * speed CONTROL/BULK OUT is handled a little differently.
-+ */
-+ if (hcd->core_if->snpsid >= OTG_CORE_REV_2_71a) {
-+ if (hc->speed == DWC_OTG_EP_SPEED_HIGH && !hc->ep_is_in &&
-+ (hc->ep_type == DWC_OTG_EP_TYPE_CONTROL ||
-+ hc->ep_type == DWC_OTG_EP_TYPE_BULK)) {
-+ out_nak_enh = 1;
-+ }
-+ }
-+
-+ if (hc->halt_status == DWC_OTG_HC_XFER_URB_DEQUEUE ||
-+ (hc->halt_status == DWC_OTG_HC_XFER_AHB_ERR
-+ && !hcd->core_if->dma_desc_enable)) {
-+ /*
-+ * Just release the channel. A dequeue can happen on a
-+ * transfer timeout. In the case of an AHB Error, the channel
-+ * was forced to halt because there's no way to gracefully
-+ * recover.
-+ */
-+ if (hcd->core_if->dma_desc_enable)
-+ dwc_otg_hcd_complete_xfer_ddma(hcd, hc, hc_regs,
-+ hc->halt_status);
-+ else
-+ release_channel(hcd, hc, qtd, hc->halt_status);
-+ return;
-+ }
-+
-+ /* Read the HCINTn register to determine the cause for the halt. */
-+
-+ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint);
-+ hcintmsk.d32 = DWC_READ_REG32(&hc_regs->hcintmsk);
-+
-+ if (hcint.b.xfercomp) {
-+ /** @todo This is here because of a possible hardware bug. Spec
-+ * says that on SPLIT-ISOC OUT transfers in DMA mode that a HALT
-+ * interrupt w/ACK bit set should occur, but I only see the
-+ * XFERCOMP bit, even with it masked out. This is a workaround
-+ * for that behavior. Should fix this when hardware is fixed.
-+ */
-+ if (hc->ep_type == DWC_OTG_EP_TYPE_ISOC && !hc->ep_is_in) {
-+ handle_hc_ack_intr(hcd, hc, hc_regs, qtd);
-+ }
-+ handle_hc_xfercomp_intr(hcd, hc, hc_regs, qtd);
-+ } else if (hcint.b.stall) {
-+ handle_hc_stall_intr(hcd, hc, hc_regs, qtd);
-+ } else if (hcint.b.xacterr && !hcd->core_if->dma_desc_enable) {
-+ if (out_nak_enh) {
-+ if (hcint.b.nyet || hcint.b.nak || hcint.b.ack) {
-+ DWC_DEBUGPL(DBG_HCD, "XactErr with NYET/NAK/ACK\n");
-+ qtd->error_count = 0;
-+ } else {
-+ DWC_DEBUGPL(DBG_HCD, "XactErr without NYET/NAK/ACK\n");
-+ }
-+ }
-+
-+ /*
-+ * Must handle xacterr before nak or ack. Could get a xacterr
-+ * at the same time as either of these on a BULK/CONTROL OUT
-+ * that started with a PING. The xacterr takes precedence.
-+ */
-+ handle_hc_xacterr_intr(hcd, hc, hc_regs, qtd);
-+ } else if (hcint.b.xcs_xact && hcd->core_if->dma_desc_enable) {
-+ handle_hc_xacterr_intr(hcd, hc, hc_regs, qtd);
-+ } else if (hcint.b.ahberr && hcd->core_if->dma_desc_enable) {
-+ handle_hc_ahberr_intr(hcd, hc, hc_regs, qtd);
-+ } else if (hcint.b.bblerr) {
-+ handle_hc_babble_intr(hcd, hc, hc_regs, qtd);
-+ } else if (hcint.b.frmovrun) {
-+ handle_hc_frmovrun_intr(hcd, hc, hc_regs, qtd);
-+ } else if (hcint.b.datatglerr) {
-+ handle_hc_datatglerr_intr(hcd, hc, hc_regs, qtd);
-+ } else if (!out_nak_enh) {
-+ if (hcint.b.nyet) {
-+ /*
-+ * Must handle nyet before nak or ack. Could get a nyet at the
-+ * same time as either of those on a BULK/CONTROL OUT that
-+ * started with a PING. The nyet takes precedence.
-+ */
-+ handle_hc_nyet_intr(hcd, hc, hc_regs, qtd);
-+ } else if (hcint.b.nak && !hcintmsk.b.nak) {
-+ /*
-+ * If nak is not masked, it's because a non-split IN transfer
-+ * is in an error state. In that case, the nak is handled by
-+ * the nak interrupt handler, not here. Handle nak here for
-+ * BULK/CONTROL OUT transfers, which halt on a NAK to allow
-+ * rewinding the buffer pointer.
-+ */
-+ handle_hc_nak_intr(hcd, hc, hc_regs, qtd);
-+ } else if (hcint.b.ack && !hcintmsk.b.ack) {
-+ /*
-+ * If ack is not masked, it's because a non-split IN transfer
-+ * is in an error state. In that case, the ack is handled by
-+ * the ack interrupt handler, not here. Handle ack here for
-+ * split transfers. Start splits halt on ACK.
-+ */
-+ handle_hc_ack_intr(hcd, hc, hc_regs, qtd);
-+ } else {
-+ if (hc->ep_type == DWC_OTG_EP_TYPE_INTR ||
-+ hc->ep_type == DWC_OTG_EP_TYPE_ISOC) {
-+ /*
-+ * A periodic transfer halted with no other channel
-+ * interrupts set. Assume it was halted by the core
-+ * because it could not be completed in its scheduled
-+ * (micro)frame.
-+ */
-+#ifdef DEBUG
-+ DWC_PRINTF
-+ ("%s: Halt channel %d (assume incomplete periodic transfer)\n",
-+ __func__, hc->hc_num);
-+#endif
-+ halt_channel(hcd, hc, qtd,
-+ DWC_OTG_HC_XFER_PERIODIC_INCOMPLETE);
-+ } else {
-+ DWC_ERROR
-+ ("%s: Channel %d, DMA Mode -- ChHltd set, but reason "
-+ "for halting is unknown, hcint 0x%08x, intsts 0x%08x\n",
-+ __func__, hc->hc_num, hcint.d32,
-+ DWC_READ_REG32(&hcd->
-+ core_if->core_global_regs->
-+ gintsts));
-+ /* Failthrough: use 3-strikes rule */
-+ qtd->error_count++;
-+ dwc_otg_hcd_save_data_toggle(hc, hc_regs, qtd);
-+ update_urb_state_xfer_intr(hc, hc_regs,
-+ qtd->urb, qtd, DWC_OTG_HC_XFER_XACT_ERR);
-+ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_XACT_ERR);
-+ }
-+
-+ }
-+ } else {
-+ DWC_PRINTF("NYET/NAK/ACK/other in non-error case, 0x%08x\n",
-+ hcint.d32);
-+ /* Failthrough: use 3-strikes rule */
-+ qtd->error_count++;
-+ dwc_otg_hcd_save_data_toggle(hc, hc_regs, qtd);
-+ update_urb_state_xfer_intr(hc, hc_regs,
-+ qtd->urb, qtd, DWC_OTG_HC_XFER_XACT_ERR);
-+ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_XACT_ERR);
-+ }
-+}
-+
-+/**
-+ * Handles a host channel Channel Halted interrupt.
-+ *
-+ * In slave mode, this handler is called only when the driver specifically
-+ * requests a halt. This occurs during handling other host channel interrupts
-+ * (e.g. nak, xacterr, stall, nyet, etc.).
-+ *
-+ * In DMA mode, this is the interrupt that occurs when the core has finished
-+ * processing a transfer on a channel. Other host channel interrupts (except
-+ * ahberr) are disabled in DMA mode.
-+ */
-+static int32_t handle_hc_chhltd_intr(dwc_otg_hcd_t * hcd,
-+ dwc_hc_t * hc,
-+ dwc_otg_hc_regs_t * hc_regs,
-+ dwc_otg_qtd_t * qtd)
-+{
-+ DWC_DEBUGPL(DBG_HCDI, "--Host Channel %d Interrupt: "
-+ "Channel Halted--\n", hc->hc_num);
-+
-+ if (hcd->core_if->dma_enable) {
-+ handle_hc_chhltd_intr_dma(hcd, hc, hc_regs, qtd);
-+ } else {
-+#ifdef DEBUG
-+ if (!halt_status_ok(hcd, hc, hc_regs, qtd)) {
-+ return 1;
-+ }
-+#endif
-+ release_channel(hcd, hc, qtd, hc->halt_status);
-+ }
-+
-+ return 1;
-+}
-+
-+
-+/**
-+ * dwc_otg_fiq_unmangle_isoc() - Update the iso_frame_desc structure on
-+ * FIQ transfer completion
-+ * @hcd: Pointer to dwc_otg_hcd struct
-+ * @num: Host channel number
-+ *
-+ * 1. Un-mangle the status as recorded in each iso_frame_desc status
-+ * 2. Copy it from the dwc_otg_urb into the real URB
-+ */
-+void dwc_otg_fiq_unmangle_isoc(dwc_otg_hcd_t *hcd, dwc_otg_qh_t *qh, dwc_otg_qtd_t *qtd, uint32_t num)
-+{
-+ struct dwc_otg_hcd_urb *dwc_urb = qtd->urb;
-+ int nr_frames = dwc_urb->packet_count;
-+ int i;
-+ hcint_data_t frame_hcint;
-+
-+ for (i = 0; i < nr_frames; i++) {
-+ frame_hcint.d32 = dwc_urb->iso_descs[i].status;
-+ if (frame_hcint.b.xfercomp) {
-+ dwc_urb->iso_descs[i].status = 0;
-+ dwc_urb->actual_length += dwc_urb->iso_descs[i].actual_length;
-+ } else if (frame_hcint.b.frmovrun) {
-+ if (qh->ep_is_in)
-+ dwc_urb->iso_descs[i].status = -DWC_E_NO_STREAM_RES;
-+ else
-+ dwc_urb->iso_descs[i].status = -DWC_E_COMMUNICATION;
-+ dwc_urb->error_count++;
-+ dwc_urb->iso_descs[i].actual_length = 0;
-+ } else if (frame_hcint.b.xacterr) {
-+ dwc_urb->iso_descs[i].status = -DWC_E_PROTOCOL;
-+ dwc_urb->error_count++;
-+ dwc_urb->iso_descs[i].actual_length = 0;
-+ } else if (frame_hcint.b.bblerr) {
-+ dwc_urb->iso_descs[i].status = -DWC_E_OVERFLOW;
-+ dwc_urb->error_count++;
-+ dwc_urb->iso_descs[i].actual_length = 0;
-+ } else {
-+ /* Something went wrong */
-+ dwc_urb->iso_descs[i].status = -1;
-+ dwc_urb->iso_descs[i].actual_length = 0;
-+ dwc_urb->error_count++;
-+ }
-+ }
-+ qh->sched_frame = dwc_frame_num_inc(qh->sched_frame, qh->interval * (nr_frames - 1));
-+
-+ //printk_ratelimited(KERN_INFO "%s: HS isochronous of %d/%d frames with %d errors complete\n",
-+ // __FUNCTION__, i, dwc_urb->packet_count, dwc_urb->error_count);
-+}
-+
-+/**
-+ * dwc_otg_fiq_unsetup_per_dma() - Remove data from bounce buffers for split transactions
-+ * @hcd: Pointer to dwc_otg_hcd struct
-+ * @num: Host channel number
-+ *
-+ * Copies data from the FIQ bounce buffers into the URB's transfer buffer. Does not modify URB state.
-+ * Returns total length of data or -1 if the buffers were not used.
-+ *
-+ */
-+int dwc_otg_fiq_unsetup_per_dma(dwc_otg_hcd_t *hcd, dwc_otg_qh_t *qh, dwc_otg_qtd_t *qtd, uint32_t num)
-+{
-+ dwc_hc_t *hc = qh->channel;
-+ struct fiq_dma_blob *blob = hcd->fiq_dmab;
-+ struct fiq_channel_state *st = &hcd->fiq_state->channel[num];
-+ uint8_t *ptr = NULL;
-+ int index = 0, len = 0;
-+ int i = 0;
-+ if (hc->ep_is_in) {
-+ /* Copy data out of the DMA bounce buffers to the URB's buffer.
-+ * The align_buf is ignored as this is ignored on FSM enqueue. */
-+ ptr = qtd->urb->buf;
-+ if (qh->ep_type == UE_ISOCHRONOUS) {
-+ /* Isoc IN transactions - grab the offset of the iso_frame_desc into the URB transfer buffer */
-+ index = qtd->isoc_frame_index;
-+ ptr += qtd->urb->iso_descs[index].offset;
-+ } else {
-+ /* Need to increment by actual_length for interrupt IN */
-+ ptr += qtd->urb->actual_length;
-+ }
-+
-+ for (i = 0; i < st->dma_info.index; i++) {
-+ len += st->dma_info.slot_len[i];
-+ dwc_memcpy(ptr, &blob->channel[num].index[i].buf[0], st->dma_info.slot_len[i]);
-+ ptr += st->dma_info.slot_len[i];
-+ }
-+ return len;
-+ } else {
-+ /* OUT endpoints - nothing to do. */
-+ return -1;
-+ }
-+
-+}
-+/**
-+ * dwc_otg_hcd_handle_hc_fsm() - handle an unmasked channel interrupt
-+ * from a channel handled in the FIQ
-+ * @hcd: Pointer to dwc_otg_hcd struct
-+ * @num: Host channel number
-+ *
-+ * If a host channel interrupt was received by the IRQ and this was a channel
-+ * used by the FIQ, the execution flow for transfer completion is substantially
-+ * different from the normal (messy) path. This function and its friends handles
-+ * channel cleanup and transaction completion from a FIQ transaction.
-+ */
-+void dwc_otg_hcd_handle_hc_fsm(dwc_otg_hcd_t *hcd, uint32_t num)
-+{
-+ struct fiq_channel_state *st = &hcd->fiq_state->channel[num];
-+ dwc_hc_t *hc = hcd->hc_ptr_array[num];
-+ dwc_otg_qtd_t *qtd = DWC_CIRCLEQ_FIRST(&hc->qh->qtd_list);
-+ dwc_otg_qh_t *qh = hc->qh;
-+ dwc_otg_hc_regs_t *hc_regs = hcd->core_if->host_if->hc_regs[num];
-+ hcint_data_t hcint = hcd->fiq_state->channel[num].hcint_copy;
-+ int hostchannels = 0;
-+ fiq_print(FIQDBG_INT, hcd->fiq_state, "OUT %01d %01d ", num , st->fsm);
-+
-+ hostchannels = hcd->available_host_channels;
-+ switch (st->fsm) {
-+ case FIQ_TEST:
-+ break;
-+
-+ case FIQ_DEQUEUE_ISSUED:
-+ /* hc_halt was called. QTD no longer exists. */
-+ /* TODO: for a nonperiodic split transaction, need to issue a
-+ * CLEAR_TT_BUFFER hub command if we were in the start-split phase.
-+ */
-+ release_channel(hcd, hc, NULL, hc->halt_status);
-+ break;
-+
-+ case FIQ_NP_SPLIT_DONE:
-+ /* Nonperiodic transaction complete. */
-+ if (!hc->ep_is_in) {
-+ qtd->ssplit_out_xfer_count = hc->xfer_len;
-+ }
-+ if (hcint.b.xfercomp) {
-+ handle_hc_xfercomp_intr(hcd, hc, hc_regs, qtd);
-+ } else if (hcint.b.nak) {
-+ handle_hc_nak_intr(hcd, hc, hc_regs, qtd);
-+ }
-+ break;
-+
-+ case FIQ_NP_SPLIT_HS_ABORTED:
-+ /* A HS abort is a 3-strikes on the HS bus at any point in the transaction.
-+ * Normally a CLEAR_TT_BUFFER hub command would be required: we can't do that
-+ * because there's no guarantee which order a non-periodic split happened in.
-+ * We could end up clearing a perfectly good transaction out of the buffer.
-+ */
-+ if (hcint.b.xacterr) {
-+ qtd->error_count += st->nr_errors;
-+ handle_hc_xacterr_intr(hcd, hc, hc_regs, qtd);
-+ } else if (hcint.b.ahberr) {
-+ handle_hc_ahberr_intr(hcd, hc, hc_regs, qtd);
-+ } else {
-+ local_fiq_disable();
-+ BUG();
-+ }
-+ break;
-+
-+ case FIQ_NP_SPLIT_LS_ABORTED:
-+ /* A few cases can cause this - either an unknown state on a SSPLIT or
-+ * STALL/data toggle error response on a CSPLIT */
-+ if (hcint.b.stall) {
-+ handle_hc_stall_intr(hcd, hc, hc_regs, qtd);
-+ } else if (hcint.b.datatglerr) {
-+ handle_hc_datatglerr_intr(hcd, hc, hc_regs, qtd);
-+ } else if (hcint.b.bblerr) {
-+ handle_hc_babble_intr(hcd, hc, hc_regs, qtd);
-+ } else if (hcint.b.ahberr) {
-+ handle_hc_ahberr_intr(hcd, hc, hc_regs, qtd);
-+ } else {
-+ local_fiq_disable();
-+ BUG();
-+ }
-+ break;
-+
-+ case FIQ_PER_SPLIT_DONE:
-+ /* Isoc IN or Interrupt IN/OUT */
-+
-+ /* Flow control here is different from the normal execution by the driver.
-+ * We need to completely ignore most of the driver's method of handling
-+ * split transactions and do it ourselves.
-+ */
-+ if (hc->ep_type == UE_INTERRUPT) {
-+ if (hcint.b.nak) {
-+ handle_hc_nak_intr(hcd, hc, hc_regs, qtd);
-+ } else if (hc->ep_is_in) {
-+ int len;
-+ len = dwc_otg_fiq_unsetup_per_dma(hcd, hc->qh, qtd, num);
-+ //printk(KERN_NOTICE "FIQ Transaction: hc=%d len=%d urb_len = %d\n", num, len, qtd->urb->length);
-+ qtd->urb->actual_length += len;
-+ if (qtd->urb->actual_length >= qtd->urb->length) {
-+ qtd->urb->status = 0;
-+ hcd->fops->complete(hcd, qtd->urb->priv, qtd->urb, qtd->urb->status);
-+ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_URB_COMPLETE);
-+ } else {
-+ /* Interrupt transfer not complete yet - is it a short read? */
-+ if (len < hc->max_packet) {
-+ /* Interrupt transaction complete */
-+ qtd->urb->status = 0;
-+ hcd->fops->complete(hcd, qtd->urb->priv, qtd->urb, qtd->urb->status);
-+ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_URB_COMPLETE);
-+ } else {
-+ /* Further transactions required */
-+ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_COMPLETE);
-+ }
-+ }
-+ } else {
-+ /* Interrupt OUT complete. */
-+ dwc_otg_hcd_save_data_toggle(hc, hc_regs, qtd);
-+ qtd->urb->actual_length += hc->xfer_len;
-+ if (qtd->urb->actual_length >= qtd->urb->length) {
-+ qtd->urb->status = 0;
-+ hcd->fops->complete(hcd, qtd->urb->priv, qtd->urb, qtd->urb->status);
-+ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_URB_COMPLETE);
-+ } else {
-+ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_COMPLETE);
-+ }
-+ }
-+ } else {
-+ /* ISOC IN complete. */
-+ struct dwc_otg_hcd_iso_packet_desc *frame_desc = &qtd->urb->iso_descs[qtd->isoc_frame_index];
-+ int len = 0;
-+ /* Record errors, update qtd. */
-+ if (st->nr_errors) {
-+ frame_desc->actual_length = 0;
-+ frame_desc->status = -DWC_E_PROTOCOL;
-+ } else {
-+ frame_desc->status = 0;
-+ /* Unswizzle dma */
-+ len = dwc_otg_fiq_unsetup_per_dma(hcd, qh, qtd, num);
-+ frame_desc->actual_length = len;
-+ }
-+ qtd->isoc_frame_index++;
-+ if (qtd->isoc_frame_index == qtd->urb->packet_count) {
-+ hcd->fops->complete(hcd, qtd->urb->priv, qtd->urb, 0);
-+ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_URB_COMPLETE);
-+ } else {
-+ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_COMPLETE);
-+ }
-+ }
-+ break;
-+
-+ case FIQ_PER_ISO_OUT_DONE: {
-+ struct dwc_otg_hcd_iso_packet_desc *frame_desc = &qtd->urb->iso_descs[qtd->isoc_frame_index];
-+ /* Record errors, update qtd. */
-+ if (st->nr_errors) {
-+ frame_desc->actual_length = 0;
-+ frame_desc->status = -DWC_E_PROTOCOL;
-+ } else {
-+ frame_desc->status = 0;
-+ frame_desc->actual_length = frame_desc->length;
-+ }
-+ qtd->isoc_frame_index++;
-+ qtd->isoc_split_offset = 0;
-+ if (qtd->isoc_frame_index == qtd->urb->packet_count) {
-+ hcd->fops->complete(hcd, qtd->urb->priv, qtd->urb, 0);
-+ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_URB_COMPLETE);
-+ } else {
-+ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_COMPLETE);
-+ }
-+ }
-+ break;
-+
-+ case FIQ_PER_SPLIT_NYET_ABORTED:
-+ /* Doh. lost the data. */
-+ printk_ratelimited(KERN_INFO "Transfer to device %d endpoint 0x%x frame %d failed "
-+ "- FIQ reported NYET. Data may have been lost.\n",
-+ hc->dev_addr, hc->ep_num, dwc_otg_hcd_get_frame_number(hcd) >> 3);
-+ if (hc->ep_type == UE_ISOCHRONOUS) {
-+ struct dwc_otg_hcd_iso_packet_desc *frame_desc = &qtd->urb->iso_descs[qtd->isoc_frame_index];
-+ /* Record errors, update qtd. */
-+ frame_desc->actual_length = 0;
-+ frame_desc->status = -DWC_E_PROTOCOL;
-+ qtd->isoc_frame_index++;
-+ qtd->isoc_split_offset = 0;
-+ if (qtd->isoc_frame_index == qtd->urb->packet_count) {
-+ hcd->fops->complete(hcd, qtd->urb->priv, qtd->urb, 0);
-+ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_URB_COMPLETE);
-+ } else {
-+ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_COMPLETE);
-+ }
-+ } else {
-+ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NO_HALT_STATUS);
-+ }
-+ break;
-+
-+ case FIQ_HS_ISOC_DONE:
-+ /* The FIQ has performed a whole pile of isochronous transactions.
-+ * The status is recorded as the interrupt state should the transaction
-+ * fail.
-+ */
-+ dwc_otg_fiq_unmangle_isoc(hcd, qh, qtd, num);
-+ hcd->fops->complete(hcd, qtd->urb->priv, qtd->urb, 0);
-+ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_URB_COMPLETE);
-+ break;
-+
-+ case FIQ_PER_SPLIT_LS_ABORTED:
-+ if (hcint.b.xacterr) {
-+ /* Hub has responded with an ERR packet. Device
-+ * has been unplugged or the port has been disabled.
-+ * TODO: need to issue a reset to the hub port. */
-+ qtd->error_count += 3;
-+ handle_hc_xacterr_intr(hcd, hc, hc_regs, qtd);
-+ } else if (hcint.b.stall) {
-+ handle_hc_stall_intr(hcd, hc, hc_regs, qtd);
-+ } else if (hcint.b.bblerr) {
-+ handle_hc_babble_intr(hcd, hc, hc_regs, qtd);
-+ } else {
-+ printk_ratelimited(KERN_INFO "Transfer to device %d endpoint 0x%x failed "
-+ "- FIQ reported FSM=%d. Data may have been lost.\n",
-+ st->fsm, hc->dev_addr, hc->ep_num);
-+ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NO_HALT_STATUS);
-+ }
-+ break;
-+
-+ case FIQ_PER_SPLIT_HS_ABORTED:
-+ /* Either the SSPLIT phase suffered transaction errors or something
-+ * unexpected happened.
-+ */
-+ qtd->error_count += 3;
-+ handle_hc_xacterr_intr(hcd, hc, hc_regs, qtd);
-+ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NO_HALT_STATUS);
-+ break;
-+
-+ case FIQ_PER_SPLIT_TIMEOUT:
-+ /* Couldn't complete in the nominated frame */
-+ printk(KERN_INFO "Transfer to device %d endpoint 0x%x frame %d failed "
-+ "- FIQ timed out. Data may have been lost.\n",
-+ hc->dev_addr, hc->ep_num, dwc_otg_hcd_get_frame_number(hcd) >> 3);
-+ if (hc->ep_type == UE_ISOCHRONOUS) {
-+ struct dwc_otg_hcd_iso_packet_desc *frame_desc = &qtd->urb->iso_descs[qtd->isoc_frame_index];
-+ /* Record errors, update qtd. */
-+ frame_desc->actual_length = 0;
-+ if (hc->ep_is_in) {
-+ frame_desc->status = -DWC_E_NO_STREAM_RES;
-+ } else {
-+ frame_desc->status = -DWC_E_COMMUNICATION;
-+ }
-+ qtd->isoc_frame_index++;
-+ if (qtd->isoc_frame_index == qtd->urb->packet_count) {
-+ hcd->fops->complete(hcd, qtd->urb->priv, qtd->urb, 0);
-+ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_URB_COMPLETE);
-+ } else {
-+ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_COMPLETE);
-+ }
-+ } else {
-+ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NO_HALT_STATUS);
-+ }
-+ break;
-+
-+ default:
-+ DWC_WARN("Unexpected state received on hc=%d fsm=%d on transfer to device %d ep 0x%x",
-+ hc->hc_num, st->fsm, hc->dev_addr, hc->ep_num);
-+ qtd->error_count++;
-+ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NO_HALT_STATUS);
-+ }
-+ return;
-+}
-+
-+/** Handles interrupt for a specific Host Channel */
-+int32_t dwc_otg_hcd_handle_hc_n_intr(dwc_otg_hcd_t * dwc_otg_hcd, uint32_t num)
-+{
-+ int retval = 0;
-+ hcint_data_t hcint;
-+ hcintmsk_data_t hcintmsk;
-+ dwc_hc_t *hc;
-+ dwc_otg_hc_regs_t *hc_regs;
-+ dwc_otg_qtd_t *qtd;
-+
-+ DWC_DEBUGPL(DBG_HCDV, "--Host Channel Interrupt--, Channel %d\n", num);
-+
-+ hc = dwc_otg_hcd->hc_ptr_array[num];
-+ hc_regs = dwc_otg_hcd->core_if->host_if->hc_regs[num];
-+ if(hc->halt_status == DWC_OTG_HC_XFER_URB_DEQUEUE) {
-+ /* We are responding to a channel disable. Driver
-+ * state is cleared - our qtd has gone away.
-+ */
-+ release_channel(dwc_otg_hcd, hc, NULL, hc->halt_status);
-+ return 1;
-+ }
-+ qtd = DWC_CIRCLEQ_FIRST(&hc->qh->qtd_list);
-+
-+ /*
-+ * FSM mode: Check to see if this is a HC interrupt from a channel handled by the FIQ.
-+ * Execution path is fundamentally different for the channels after a FIQ has completed
-+ * a split transaction.
-+ */
-+ if (fiq_fsm_enable) {
-+ switch (dwc_otg_hcd->fiq_state->channel[num].fsm) {
-+ case FIQ_PASSTHROUGH:
-+ break;
-+ case FIQ_PASSTHROUGH_ERRORSTATE:
-+ /* Hook into the error count */
-+ fiq_print(FIQDBG_ERR, dwc_otg_hcd->fiq_state, "HCDERR%02d", num);
-+ if (!dwc_otg_hcd->fiq_state->channel[num].nr_errors) {
-+ qtd->error_count = 0;
-+ fiq_print(FIQDBG_ERR, dwc_otg_hcd->fiq_state, "RESET ");
-+ }
-+ break;
-+ default:
-+ dwc_otg_hcd_handle_hc_fsm(dwc_otg_hcd, num);
-+ return 1;
-+ }
-+ }
-+
-+ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint);
-+ hcintmsk.d32 = DWC_READ_REG32(&hc_regs->hcintmsk);
-+ hcint.d32 = hcint.d32 & hcintmsk.d32;
-+ if (!dwc_otg_hcd->core_if->dma_enable) {
-+ if (hcint.b.chhltd && hcint.d32 != 0x2) {
-+ hcint.b.chhltd = 0;
-+ }
-+ }
-+
-+ if (hcint.b.xfercomp) {
-+ retval |=
-+ handle_hc_xfercomp_intr(dwc_otg_hcd, hc, hc_regs, qtd);
-+ /*
-+ * If NYET occurred at same time as Xfer Complete, the NYET is
-+ * handled by the Xfer Complete interrupt handler. Don't want
-+ * to call the NYET interrupt handler in this case.
-+ */
-+ hcint.b.nyet = 0;
-+ }
-+ if (hcint.b.chhltd) {
-+ retval |= handle_hc_chhltd_intr(dwc_otg_hcd, hc, hc_regs, qtd);
-+ }
-+ if (hcint.b.ahberr) {
-+ retval |= handle_hc_ahberr_intr(dwc_otg_hcd, hc, hc_regs, qtd);
-+ }
-+ if (hcint.b.stall) {
-+ retval |= handle_hc_stall_intr(dwc_otg_hcd, hc, hc_regs, qtd);
-+ }
-+ if (hcint.b.nak) {
-+ retval |= handle_hc_nak_intr(dwc_otg_hcd, hc, hc_regs, qtd);
-+ }
-+ if (hcint.b.ack) {
-+ if(!hcint.b.chhltd)
-+ retval |= handle_hc_ack_intr(dwc_otg_hcd, hc, hc_regs, qtd);
-+ }
-+ if (hcint.b.nyet) {
-+ retval |= handle_hc_nyet_intr(dwc_otg_hcd, hc, hc_regs, qtd);
-+ }
-+ if (hcint.b.xacterr) {
-+ retval |= handle_hc_xacterr_intr(dwc_otg_hcd, hc, hc_regs, qtd);
-+ }
-+ if (hcint.b.bblerr) {
-+ retval |= handle_hc_babble_intr(dwc_otg_hcd, hc, hc_regs, qtd);
-+ }
-+ if (hcint.b.frmovrun) {
-+ retval |=
-+ handle_hc_frmovrun_intr(dwc_otg_hcd, hc, hc_regs, qtd);
-+ }
-+ if (hcint.b.datatglerr) {
-+ retval |=
-+ handle_hc_datatglerr_intr(dwc_otg_hcd, hc, hc_regs, qtd);
-+ }
-+
-+ return retval;
-+}
-+#endif /* DWC_DEVICE_ONLY */
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_hcd_linux.c
-@@ -0,0 +1,1005 @@
-+
-+/* ==========================================================================
-+ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_hcd_linux.c $
-+ * $Revision: #20 $
-+ * $Date: 2011/10/26 $
-+ * $Change: 1872981 $
-+ *
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+#ifndef DWC_DEVICE_ONLY
-+
-+/**
-+ * @file
-+ *
-+ * This file contains the implementation of the HCD. In Linux, the HCD
-+ * implements the hc_driver API.
-+ */
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+#include <linux/moduleparam.h>
-+#include <linux/init.h>
-+#include <linux/device.h>
-+#include <linux/errno.h>
-+#include <linux/list.h>
-+#include <linux/interrupt.h>
-+#include <linux/string.h>
-+#include <linux/dma-mapping.h>
-+#include <linux/version.h>
-+#include <asm/io.h>
-+#include <asm/fiq.h>
-+#include <linux/usb.h>
-+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,35)
-+#include <../drivers/usb/core/hcd.h>
-+#else
-+#include <linux/usb/hcd.h>
-+#endif
-+#include <asm/bug.h>
-+
-+#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,30))
-+#define USB_URB_EP_LINKING 1
-+#else
-+#define USB_URB_EP_LINKING 0
-+#endif
-+
-+#include "dwc_otg_hcd_if.h"
-+#include "dwc_otg_dbg.h"
-+#include "dwc_otg_driver.h"
-+#include "dwc_otg_hcd.h"
-+
-+extern unsigned char _dwc_otg_fiq_stub, _dwc_otg_fiq_stub_end;
-+
-+/**
-+ * Gets the endpoint number from a _bEndpointAddress argument. The endpoint is
-+ * qualified with its direction (possible 32 endpoints per device).
-+ */
-+#define dwc_ep_addr_to_endpoint(_bEndpointAddress_) ((_bEndpointAddress_ & USB_ENDPOINT_NUMBER_MASK) | \
-+ ((_bEndpointAddress_ & USB_DIR_IN) != 0) << 4)
-+
-+static const char dwc_otg_hcd_name[] = "dwc_otg_hcd";
-+
-+extern bool fiq_enable;
-+
-+/** @name Linux HC Driver API Functions */
-+/** @{ */
-+/* manage i/o requests, device state */
-+static int dwc_otg_urb_enqueue(struct usb_hcd *hcd,
-+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28)
-+ struct usb_host_endpoint *ep,
-+#endif
-+ struct urb *urb, gfp_t mem_flags);
-+
-+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,30)
-+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28)
-+static int dwc_otg_urb_dequeue(struct usb_hcd *hcd, struct urb *urb);
-+#endif
-+#else /* kernels at or post 2.6.30 */
-+static int dwc_otg_urb_dequeue(struct usb_hcd *hcd,
-+ struct urb *urb, int status);
-+#endif /* LINUX_VERSION_CODE < KERNEL_VERSION(2,6,30) */
-+
-+static void endpoint_disable(struct usb_hcd *hcd, struct usb_host_endpoint *ep);
-+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,30)
-+static void endpoint_reset(struct usb_hcd *hcd, struct usb_host_endpoint *ep);
-+#endif
-+static irqreturn_t dwc_otg_hcd_irq(struct usb_hcd *hcd);
-+extern int hcd_start(struct usb_hcd *hcd);
-+extern void hcd_stop(struct usb_hcd *hcd);
-+static int get_frame_number(struct usb_hcd *hcd);
-+extern int hub_status_data(struct usb_hcd *hcd, char *buf);
-+extern int hub_control(struct usb_hcd *hcd,
-+ u16 typeReq,
-+ u16 wValue, u16 wIndex, char *buf, u16 wLength);
-+
-+struct wrapper_priv_data {
-+ dwc_otg_hcd_t *dwc_otg_hcd;
-+};
-+
-+/** @} */
-+
-+static struct hc_driver dwc_otg_hc_driver = {
-+
-+ .description = dwc_otg_hcd_name,
-+ .product_desc = "DWC OTG Controller",
-+ .hcd_priv_size = sizeof(struct wrapper_priv_data),
-+
-+ .irq = dwc_otg_hcd_irq,
-+
-+ .flags = HCD_MEMORY | HCD_USB2,
-+
-+ //.reset =
-+ .start = hcd_start,
-+ //.suspend =
-+ //.resume =
-+ .stop = hcd_stop,
-+
-+ .urb_enqueue = dwc_otg_urb_enqueue,
-+ .urb_dequeue = dwc_otg_urb_dequeue,
-+ .endpoint_disable = endpoint_disable,
-+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,30)
-+ .endpoint_reset = endpoint_reset,
-+#endif
-+ .get_frame_number = get_frame_number,
-+
-+ .hub_status_data = hub_status_data,
-+ .hub_control = hub_control,
-+ //.bus_suspend =
-+ //.bus_resume =
-+};
-+
-+/** Gets the dwc_otg_hcd from a struct usb_hcd */
-+static inline dwc_otg_hcd_t *hcd_to_dwc_otg_hcd(struct usb_hcd *hcd)
-+{
-+ struct wrapper_priv_data *p;
-+ p = (struct wrapper_priv_data *)(hcd->hcd_priv);
-+ return p->dwc_otg_hcd;
-+}
-+
-+/** Gets the struct usb_hcd that contains a dwc_otg_hcd_t. */
-+static inline struct usb_hcd *dwc_otg_hcd_to_hcd(dwc_otg_hcd_t * dwc_otg_hcd)
-+{
-+ return dwc_otg_hcd_get_priv_data(dwc_otg_hcd);
-+}
-+
-+/** Gets the usb_host_endpoint associated with an URB. */
-+inline struct usb_host_endpoint *dwc_urb_to_endpoint(struct urb *urb)
-+{
-+ struct usb_device *dev = urb->dev;
-+ int ep_num = usb_pipeendpoint(urb->pipe);
-+
-+ if (usb_pipein(urb->pipe))
-+ return dev->ep_in[ep_num];
-+ else
-+ return dev->ep_out[ep_num];
-+}
-+
-+static int _disconnect(dwc_otg_hcd_t * hcd)
-+{
-+ struct usb_hcd *usb_hcd = dwc_otg_hcd_to_hcd(hcd);
-+
-+ usb_hcd->self.is_b_host = 0;
-+ return 0;
-+}
-+
-+static int _start(dwc_otg_hcd_t * hcd)
-+{
-+ struct usb_hcd *usb_hcd = dwc_otg_hcd_to_hcd(hcd);
-+
-+ usb_hcd->self.is_b_host = dwc_otg_hcd_is_b_host(hcd);
-+ hcd_start(usb_hcd);
-+
-+ return 0;
-+}
-+
-+static int _hub_info(dwc_otg_hcd_t * hcd, void *urb_handle, uint32_t * hub_addr,
-+ uint32_t * port_addr)
-+{
-+ struct urb *urb = (struct urb *)urb_handle;
-+ struct usb_bus *bus;
-+#if 1 //GRAYG - temporary
-+ if (NULL == urb_handle)
-+ DWC_ERROR("**** %s - NULL URB handle\n", __func__);//GRAYG
-+ if (NULL == urb->dev)
-+ DWC_ERROR("**** %s - URB has no device\n", __func__);//GRAYG
-+ if (NULL == port_addr)
-+ DWC_ERROR("**** %s - NULL port_address\n", __func__);//GRAYG
-+#endif
-+ if (urb->dev->tt) {
-+ if (NULL == urb->dev->tt->hub) {
-+ DWC_ERROR("**** %s - (URB's transactor has no TT - giving no hub)\n",
-+ __func__); //GRAYG
-+ //*hub_addr = (u8)usb_pipedevice(urb->pipe); //GRAYG
-+ *hub_addr = 0; //GRAYG
-+ // we probably shouldn't have a transaction translator if
-+ // there's no associated hub?
-+ } else {
-+ bus = hcd_to_bus(dwc_otg_hcd_to_hcd(hcd));
-+ if (urb->dev->tt->hub == bus->root_hub)
-+ *hub_addr = 0;
-+ else
-+ *hub_addr = urb->dev->tt->hub->devnum;
-+ }
-+ *port_addr = urb->dev->tt->multi ? urb->dev->ttport : 1;
-+ } else {
-+ *hub_addr = 0;
-+ *port_addr = urb->dev->ttport;
-+ }
-+ return 0;
-+}
-+
-+static int _speed(dwc_otg_hcd_t * hcd, void *urb_handle)
-+{
-+ struct urb *urb = (struct urb *)urb_handle;
-+ return urb->dev->speed;
-+}
-+
-+static int _get_b_hnp_enable(dwc_otg_hcd_t * hcd)
-+{
-+ struct usb_hcd *usb_hcd = dwc_otg_hcd_to_hcd(hcd);
-+ return usb_hcd->self.b_hnp_enable;
-+}
-+
-+static void allocate_bus_bandwidth(struct usb_hcd *hcd, uint32_t bw,
-+ struct urb *urb)
-+{
-+ hcd_to_bus(hcd)->bandwidth_allocated += bw / urb->interval;
-+ if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) {
-+ hcd_to_bus(hcd)->bandwidth_isoc_reqs++;
-+ } else {
-+ hcd_to_bus(hcd)->bandwidth_int_reqs++;
-+ }
-+}
-+
-+static void free_bus_bandwidth(struct usb_hcd *hcd, uint32_t bw,
-+ struct urb *urb)
-+{
-+ hcd_to_bus(hcd)->bandwidth_allocated -= bw / urb->interval;
-+ if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) {
-+ hcd_to_bus(hcd)->bandwidth_isoc_reqs--;
-+ } else {
-+ hcd_to_bus(hcd)->bandwidth_int_reqs--;
-+ }
-+}
-+
-+/**
-+ * Sets the final status of an URB and returns it to the device driver. Any
-+ * required cleanup of the URB is performed. The HCD lock should be held on
-+ * entry.
-+ */
-+static int _complete(dwc_otg_hcd_t * hcd, void *urb_handle,
-+ dwc_otg_hcd_urb_t * dwc_otg_urb, int32_t status)
-+{
-+ struct urb *urb = (struct urb *)urb_handle;
-+ urb_tq_entry_t *new_entry;
-+ int rc = 0;
-+ if (CHK_DEBUG_LEVEL(DBG_HCDV | DBG_HCD_URB)) {
-+ DWC_PRINTF("%s: urb %p, device %d, ep %d %s, status=%d\n",
-+ __func__, urb, usb_pipedevice(urb->pipe),
-+ usb_pipeendpoint(urb->pipe),
-+ usb_pipein(urb->pipe) ? "IN" : "OUT", status);
-+ if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) {
-+ int i;
-+ for (i = 0; i < urb->number_of_packets; i++) {
-+ DWC_PRINTF(" ISO Desc %d status: %d\n",
-+ i, urb->iso_frame_desc[i].status);
-+ }
-+ }
-+ }
-+ new_entry = DWC_ALLOC_ATOMIC(sizeof(urb_tq_entry_t));
-+ urb->actual_length = dwc_otg_hcd_urb_get_actual_length(dwc_otg_urb);
-+ /* Convert status value. */
-+ switch (status) {
-+ case -DWC_E_PROTOCOL:
-+ status = -EPROTO;
-+ break;
-+ case -DWC_E_IN_PROGRESS:
-+ status = -EINPROGRESS;
-+ break;
-+ case -DWC_E_PIPE:
-+ status = -EPIPE;
-+ break;
-+ case -DWC_E_IO:
-+ status = -EIO;
-+ break;
-+ case -DWC_E_TIMEOUT:
-+ status = -ETIMEDOUT;
-+ break;
-+ case -DWC_E_OVERFLOW:
-+ status = -EOVERFLOW;
-+ break;
-+ case -DWC_E_SHUTDOWN:
-+ status = -ESHUTDOWN;
-+ break;
-+ default:
-+ if (status) {
-+ DWC_PRINTF("Uknown urb status %d\n", status);
-+
-+ }
-+ }
-+
-+ if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) {
-+ int i;
-+
-+ urb->error_count = dwc_otg_hcd_urb_get_error_count(dwc_otg_urb);
-+ for (i = 0; i < urb->number_of_packets; ++i) {
-+ urb->iso_frame_desc[i].actual_length =
-+ dwc_otg_hcd_urb_get_iso_desc_actual_length
-+ (dwc_otg_urb, i);
-+ urb->iso_frame_desc[i].status =
-+ dwc_otg_hcd_urb_get_iso_desc_status(dwc_otg_urb, i);
-+ }
-+ }
-+
-+ urb->status = status;
-+ urb->hcpriv = NULL;
-+ if (!status) {
-+ if ((urb->transfer_flags & URB_SHORT_NOT_OK) &&
-+ (urb->actual_length < urb->transfer_buffer_length)) {
-+ urb->status = -EREMOTEIO;
-+ }
-+ }
-+
-+ if ((usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) ||
-+ (usb_pipetype(urb->pipe) == PIPE_INTERRUPT)) {
-+ struct usb_host_endpoint *ep = dwc_urb_to_endpoint(urb);
-+ if (ep) {
-+ free_bus_bandwidth(dwc_otg_hcd_to_hcd(hcd),
-+ dwc_otg_hcd_get_ep_bandwidth(hcd,
-+ ep->hcpriv),
-+ urb);
-+ }
-+ }
-+ DWC_FREE(dwc_otg_urb);
-+ if (!new_entry) {
-+ DWC_ERROR("dwc_otg_hcd: complete: cannot allocate URB TQ entry\n");
-+ urb->status = -EPROTO;
-+ /* don't schedule the tasklet -
-+ * directly return the packet here with error. */
-+#if USB_URB_EP_LINKING
-+ usb_hcd_unlink_urb_from_ep(dwc_otg_hcd_to_hcd(hcd), urb);
-+#endif
-+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28)
-+ usb_hcd_giveback_urb(dwc_otg_hcd_to_hcd(hcd), urb);
-+#else
-+ usb_hcd_giveback_urb(dwc_otg_hcd_to_hcd(hcd), urb, urb->status);
-+#endif
-+ } else {
-+ new_entry->urb = urb;
-+#if USB_URB_EP_LINKING
-+ rc = usb_hcd_check_unlink_urb(dwc_otg_hcd_to_hcd(hcd), urb, urb->status);
-+ if(0 == rc) {
-+ usb_hcd_unlink_urb_from_ep(dwc_otg_hcd_to_hcd(hcd), urb);
-+ }
-+#endif
-+ if(0 == rc) {
-+ DWC_TAILQ_INSERT_TAIL(&hcd->completed_urb_list, new_entry,
-+ urb_tq_entries);
-+ DWC_TASK_HI_SCHEDULE(hcd->completion_tasklet);
-+ }
-+ }
-+ return 0;
-+}
-+
-+static struct dwc_otg_hcd_function_ops hcd_fops = {
-+ .start = _start,
-+ .disconnect = _disconnect,
-+ .hub_info = _hub_info,
-+ .speed = _speed,
-+ .complete = _complete,
-+ .get_b_hnp_enable = _get_b_hnp_enable,
-+};
-+
-+static struct fiq_handler fh = {
-+ .name = "usb_fiq",
-+};
-+
-+static void hcd_init_fiq(void *cookie)
-+{
-+ dwc_otg_device_t *otg_dev = cookie;
-+ dwc_otg_hcd_t *dwc_otg_hcd = otg_dev->hcd;
-+ struct pt_regs regs;
-+ int irq;
-+
-+ if (claim_fiq(&fh)) {
-+ DWC_ERROR("Can't claim FIQ");
-+ BUG();
-+ }
-+ DWC_WARN("FIQ on core %d at 0x%08x",
-+ smp_processor_id(),
-+ (fiq_fsm_enable ? (int)&dwc_otg_fiq_fsm : (int)&dwc_otg_fiq_nop));
-+ DWC_WARN("FIQ ASM at 0x%08x length %d", (int)&_dwc_otg_fiq_stub, (int)(&_dwc_otg_fiq_stub_end - &_dwc_otg_fiq_stub));
-+ set_fiq_handler((void *) &_dwc_otg_fiq_stub, &_dwc_otg_fiq_stub_end - &_dwc_otg_fiq_stub);
-+ memset(®s,0,sizeof(regs));
-+
-+ regs.ARM_r8 = (long) dwc_otg_hcd->fiq_state;
-+ if (fiq_fsm_enable) {
-+ regs.ARM_r9 = dwc_otg_hcd->core_if->core_params->host_channels;
-+ //regs.ARM_r10 = dwc_otg_hcd->dma;
-+ regs.ARM_fp = (long) dwc_otg_fiq_fsm;
-+ } else {
-+ regs.ARM_fp = (long) dwc_otg_fiq_nop;
-+ }
-+
-+ regs.ARM_sp = (long) dwc_otg_hcd->fiq_stack + (sizeof(struct fiq_stack) - 4);
-+
-+// __show_regs(®s);
-+ set_fiq_regs(®s);
-+
-+ //Set the mphi periph to the required registers
-+ dwc_otg_hcd->fiq_state->mphi_regs.base = otg_dev->os_dep.mphi_base;
-+ dwc_otg_hcd->fiq_state->mphi_regs.ctrl = otg_dev->os_dep.mphi_base + 0x4c;
-+ dwc_otg_hcd->fiq_state->mphi_regs.outdda = otg_dev->os_dep.mphi_base + 0x28;
-+ dwc_otg_hcd->fiq_state->mphi_regs.outddb = otg_dev->os_dep.mphi_base + 0x2c;
-+ dwc_otg_hcd->fiq_state->mphi_regs.intstat = otg_dev->os_dep.mphi_base + 0x50;
-+ dwc_otg_hcd->fiq_state->dwc_regs_base = otg_dev->os_dep.base;
-+ DWC_WARN("MPHI regs_base at 0x%08x", (int)dwc_otg_hcd->fiq_state->mphi_regs.base);
-+ //Enable mphi peripheral
-+ writel((1<<31),dwc_otg_hcd->fiq_state->mphi_regs.ctrl);
-+#ifdef DEBUG
-+ if (readl(dwc_otg_hcd->fiq_state->mphi_regs.ctrl) & 0x80000000)
-+ DWC_WARN("MPHI periph has been enabled");
-+ else
-+ DWC_WARN("MPHI periph has NOT been enabled");
-+#endif
-+ // Enable FIQ interrupt from USB peripheral
-+#ifdef CONFIG_MULTI_IRQ_HANDLER
-+ irq = platform_get_irq(otg_dev->os_dep.platformdev, 1);
-+#else
-+ irq = INTERRUPT_VC_USB;
-+#endif
-+ if (irq < 0) {
-+ DWC_ERROR("Can't get FIQ irq");
-+ return;
-+ }
-+ enable_fiq(irq);
-+ local_fiq_enable();
-+}
-+
-+/**
-+ * Initializes the HCD. This function allocates memory for and initializes the
-+ * static parts of the usb_hcd and dwc_otg_hcd structures. It also registers the
-+ * USB bus with the core and calls the hc_driver->start() function. It returns
-+ * a negative error on failure.
-+ */
-+int hcd_init(dwc_bus_dev_t *_dev)
-+{
-+ struct usb_hcd *hcd = NULL;
-+ dwc_otg_hcd_t *dwc_otg_hcd = NULL;
-+ dwc_otg_device_t *otg_dev = DWC_OTG_BUSDRVDATA(_dev);
-+ int retval = 0;
-+ u64 dmamask;
-+
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD INIT otg_dev=%p\n", otg_dev);
-+
-+ /* Set device flags indicating whether the HCD supports DMA. */
-+ if (dwc_otg_is_dma_enable(otg_dev->core_if))
-+ dmamask = DMA_BIT_MASK(32);
-+ else
-+ dmamask = 0;
-+
-+#if defined(LM_INTERFACE) || defined(PLATFORM_INTERFACE)
-+ dma_set_mask(&_dev->dev, dmamask);
-+ dma_set_coherent_mask(&_dev->dev, dmamask);
-+#elif defined(PCI_INTERFACE)
-+ pci_set_dma_mask(_dev, dmamask);
-+ pci_set_consistent_dma_mask(_dev, dmamask);
-+#endif
-+
-+ /*
-+ * Allocate memory for the base HCD plus the DWC OTG HCD.
-+ * Initialize the base HCD.
-+ */
-+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,30)
-+ hcd = usb_create_hcd(&dwc_otg_hc_driver, &_dev->dev, _dev->dev.bus_id);
-+#else
-+ hcd = usb_create_hcd(&dwc_otg_hc_driver, &_dev->dev, dev_name(&_dev->dev));
-+ hcd->has_tt = 1;
-+// hcd->uses_new_polling = 1;
-+// hcd->poll_rh = 0;
-+#endif
-+ if (!hcd) {
-+ retval = -ENOMEM;
-+ goto error1;
-+ }
-+
-+ hcd->regs = otg_dev->os_dep.base;
-+
-+
-+ /* Initialize the DWC OTG HCD. */
-+ dwc_otg_hcd = dwc_otg_hcd_alloc_hcd();
-+ if (!dwc_otg_hcd) {
-+ goto error2;
-+ }
-+ ((struct wrapper_priv_data *)(hcd->hcd_priv))->dwc_otg_hcd =
-+ dwc_otg_hcd;
-+ otg_dev->hcd = dwc_otg_hcd;
-+
-+ if (dwc_otg_hcd_init(dwc_otg_hcd, otg_dev->core_if)) {
-+ goto error2;
-+ }
-+
-+ if (fiq_enable) {
-+ if (num_online_cpus() > 1) {
-+ /* bcm2709: can run the FIQ on a separate core to IRQs */
-+ smp_call_function_single(1, hcd_init_fiq, otg_dev, 1);
-+ } else {
-+ smp_call_function_single(0, hcd_init_fiq, otg_dev, 1);
-+ }
-+ }
-+
-+ otg_dev->hcd->otg_dev = otg_dev;
-+ hcd->self.otg_port = dwc_otg_hcd_otg_port(dwc_otg_hcd);
-+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,33) //don't support for LM(with 2.6.20.1 kernel)
-+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,35) //version field absent later
-+ hcd->self.otg_version = dwc_otg_get_otg_version(otg_dev->core_if);
-+#endif
-+ /* Don't support SG list at this point */
-+ hcd->self.sg_tablesize = 0;
-+#endif
-+ /*
-+ * Finish generic HCD initialization and start the HCD. This function
-+ * allocates the DMA buffer pool, registers the USB bus, requests the
-+ * IRQ line, and calls hcd_start method.
-+ */
-+#ifdef PLATFORM_INTERFACE
-+ retval = usb_add_hcd(hcd, platform_get_irq(_dev, fiq_enable ? 0 : 1), IRQF_SHARED);
-+#else
-+ retval = usb_add_hcd(hcd, _dev->irq, IRQF_SHARED);
-+#endif
-+ if (retval < 0) {
-+ goto error2;
-+ }
-+
-+ dwc_otg_hcd_set_priv_data(dwc_otg_hcd, hcd);
-+ return 0;
-+
-+error2:
-+ usb_put_hcd(hcd);
-+error1:
-+ return retval;
-+}
-+
-+/**
-+ * Removes the HCD.
-+ * Frees memory and resources associated with the HCD and deregisters the bus.
-+ */
-+void hcd_remove(dwc_bus_dev_t *_dev)
-+{
-+ dwc_otg_device_t *otg_dev = DWC_OTG_BUSDRVDATA(_dev);
-+ dwc_otg_hcd_t *dwc_otg_hcd;
-+ struct usb_hcd *hcd;
-+
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD REMOVE otg_dev=%p\n", otg_dev);
-+
-+ if (!otg_dev) {
-+ DWC_DEBUGPL(DBG_ANY, "%s: otg_dev NULL!\n", __func__);
-+ return;
-+ }
-+
-+ dwc_otg_hcd = otg_dev->hcd;
-+
-+ if (!dwc_otg_hcd) {
-+ DWC_DEBUGPL(DBG_ANY, "%s: otg_dev->hcd NULL!\n", __func__);
-+ return;
-+ }
-+
-+ hcd = dwc_otg_hcd_to_hcd(dwc_otg_hcd);
-+
-+ if (!hcd) {
-+ DWC_DEBUGPL(DBG_ANY,
-+ "%s: dwc_otg_hcd_to_hcd(dwc_otg_hcd) NULL!\n",
-+ __func__);
-+ return;
-+ }
-+ usb_remove_hcd(hcd);
-+ dwc_otg_hcd_set_priv_data(dwc_otg_hcd, NULL);
-+ dwc_otg_hcd_remove(dwc_otg_hcd);
-+ usb_put_hcd(hcd);
-+}
-+
-+/* =========================================================================
-+ * Linux HC Driver Functions
-+ * ========================================================================= */
-+
-+/** Initializes the DWC_otg controller and its root hub and prepares it for host
-+ * mode operation. Activates the root port. Returns 0 on success and a negative
-+ * error code on failure. */
-+int hcd_start(struct usb_hcd *hcd)
-+{
-+ dwc_otg_hcd_t *dwc_otg_hcd = hcd_to_dwc_otg_hcd(hcd);
-+ struct usb_bus *bus;
-+
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD START\n");
-+ bus = hcd_to_bus(hcd);
-+
-+ hcd->state = HC_STATE_RUNNING;
-+ if (dwc_otg_hcd_start(dwc_otg_hcd, &hcd_fops)) {
-+ return 0;
-+ }
-+
-+ /* Initialize and connect root hub if one is not already attached */
-+ if (bus->root_hub) {
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD Has Root Hub\n");
-+ /* Inform the HUB driver to resume. */
-+ usb_hcd_resume_root_hub(hcd);
-+ }
-+
-+ return 0;
-+}
-+
-+/**
-+ * Halts the DWC_otg host mode operations in a clean manner. USB transfers are
-+ * stopped.
-+ */
-+void hcd_stop(struct usb_hcd *hcd)
-+{
-+ dwc_otg_hcd_t *dwc_otg_hcd = hcd_to_dwc_otg_hcd(hcd);
-+
-+ dwc_otg_hcd_stop(dwc_otg_hcd);
-+}
-+
-+/** Returns the current frame number. */
-+static int get_frame_number(struct usb_hcd *hcd)
-+{
-+ hprt0_data_t hprt0;
-+ dwc_otg_hcd_t *dwc_otg_hcd = hcd_to_dwc_otg_hcd(hcd);
-+ hprt0.d32 = DWC_READ_REG32(dwc_otg_hcd->core_if->host_if->hprt0);
-+ if (hprt0.b.prtspd == DWC_HPRT0_PRTSPD_HIGH_SPEED)
-+ return dwc_otg_hcd_get_frame_number(dwc_otg_hcd) >> 3;
-+ else
-+ return dwc_otg_hcd_get_frame_number(dwc_otg_hcd);
-+}
-+
-+#ifdef DEBUG
-+static void dump_urb_info(struct urb *urb, char *fn_name)
-+{
-+ DWC_PRINTF("%s, urb %p\n", fn_name, urb);
-+ DWC_PRINTF(" Device address: %d\n", usb_pipedevice(urb->pipe));
-+ DWC_PRINTF(" Endpoint: %d, %s\n", usb_pipeendpoint(urb->pipe),
-+ (usb_pipein(urb->pipe) ? "IN" : "OUT"));
-+ DWC_PRINTF(" Endpoint type: %s\n", ( {
-+ char *pipetype;
-+ switch (usb_pipetype(urb->pipe)) {
-+case PIPE_CONTROL:
-+pipetype = "CONTROL"; break; case PIPE_BULK:
-+pipetype = "BULK"; break; case PIPE_INTERRUPT:
-+pipetype = "INTERRUPT"; break; case PIPE_ISOCHRONOUS:
-+pipetype = "ISOCHRONOUS"; break; default:
-+ pipetype = "UNKNOWN"; break;};
-+ pipetype;}
-+ )) ;
-+ DWC_PRINTF(" Speed: %s\n", ( {
-+ char *speed; switch (urb->dev->speed) {
-+case USB_SPEED_HIGH:
-+speed = "HIGH"; break; case USB_SPEED_FULL:
-+speed = "FULL"; break; case USB_SPEED_LOW:
-+speed = "LOW"; break; default:
-+ speed = "UNKNOWN"; break;};
-+ speed;}
-+ )) ;
-+ DWC_PRINTF(" Max packet size: %d\n",
-+ usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe)));
-+ DWC_PRINTF(" Data buffer length: %d\n", urb->transfer_buffer_length);
-+ DWC_PRINTF(" Transfer buffer: %p, Transfer DMA: %p\n",
-+ urb->transfer_buffer, (void *)urb->transfer_dma);
-+ DWC_PRINTF(" Setup buffer: %p, Setup DMA: %p\n",
-+ urb->setup_packet, (void *)urb->setup_dma);
-+ DWC_PRINTF(" Interval: %d\n", urb->interval);
-+ if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) {
-+ int i;
-+ for (i = 0; i < urb->number_of_packets; i++) {
-+ DWC_PRINTF(" ISO Desc %d:\n", i);
-+ DWC_PRINTF(" offset: %d, length %d\n",
-+ urb->iso_frame_desc[i].offset,
-+ urb->iso_frame_desc[i].length);
-+ }
-+ }
-+}
-+#endif
-+
-+/** Starts processing a USB transfer request specified by a USB Request Block
-+ * (URB). mem_flags indicates the type of memory allocation to use while
-+ * processing this URB. */
-+static int dwc_otg_urb_enqueue(struct usb_hcd *hcd,
-+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28)
-+ struct usb_host_endpoint *ep,
-+#endif
-+ struct urb *urb, gfp_t mem_flags)
-+{
-+ int retval = 0;
-+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,28)
-+ struct usb_host_endpoint *ep = urb->ep;
-+#endif
-+ dwc_irqflags_t irqflags;
-+ void **ref_ep_hcpriv = &ep->hcpriv;
-+ dwc_otg_hcd_t *dwc_otg_hcd = hcd_to_dwc_otg_hcd(hcd);
-+ dwc_otg_hcd_urb_t *dwc_otg_urb;
-+ int i;
-+ int alloc_bandwidth = 0;
-+ uint8_t ep_type = 0;
-+ uint32_t flags = 0;
-+ void *buf;
-+
-+#ifdef DEBUG
-+ if (CHK_DEBUG_LEVEL(DBG_HCDV | DBG_HCD_URB)) {
-+ dump_urb_info(urb, "dwc_otg_urb_enqueue");
-+ }
-+#endif
-+
-+ if (!urb->transfer_buffer && urb->transfer_buffer_length)
-+ return -EINVAL;
-+
-+ if ((usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS)
-+ || (usb_pipetype(urb->pipe) == PIPE_INTERRUPT)) {
-+ if (!dwc_otg_hcd_is_bandwidth_allocated
-+ (dwc_otg_hcd, ref_ep_hcpriv)) {
-+ alloc_bandwidth = 1;
-+ }
-+ }
-+
-+ switch (usb_pipetype(urb->pipe)) {
-+ case PIPE_CONTROL:
-+ ep_type = USB_ENDPOINT_XFER_CONTROL;
-+ break;
-+ case PIPE_ISOCHRONOUS:
-+ ep_type = USB_ENDPOINT_XFER_ISOC;
-+ break;
-+ case PIPE_BULK:
-+ ep_type = USB_ENDPOINT_XFER_BULK;
-+ break;
-+ case PIPE_INTERRUPT:
-+ ep_type = USB_ENDPOINT_XFER_INT;
-+ break;
-+ default:
-+ DWC_WARN("Wrong EP type - %d\n", usb_pipetype(urb->pipe));
-+ }
-+
-+ /* # of packets is often 0 - do we really need to call this then? */
-+ dwc_otg_urb = dwc_otg_hcd_urb_alloc(dwc_otg_hcd,
-+ urb->number_of_packets,
-+ mem_flags == GFP_ATOMIC ? 1 : 0);
-+
-+ if(dwc_otg_urb == NULL)
-+ return -ENOMEM;
-+
-+ if (!dwc_otg_urb && urb->number_of_packets)
-+ return -ENOMEM;
-+
-+ dwc_otg_hcd_urb_set_pipeinfo(dwc_otg_urb, usb_pipedevice(urb->pipe),
-+ usb_pipeendpoint(urb->pipe), ep_type,
-+ usb_pipein(urb->pipe),
-+ usb_maxpacket(urb->dev, urb->pipe,
-+ !(usb_pipein(urb->pipe))));
-+
-+ buf = urb->transfer_buffer;
-+ if (hcd->self.uses_dma && !buf && urb->transfer_buffer_length) {
-+ /*
-+ * Calculate virtual address from physical address,
-+ * because some class driver may not fill transfer_buffer.
-+ * In Buffer DMA mode virual address is used,
-+ * when handling non DWORD aligned buffers.
-+ */
-+ buf = (void *)__bus_to_virt((unsigned long)urb->transfer_dma);
-+ dev_warn_once(&urb->dev->dev,
-+ "USB transfer_buffer was NULL, will use __bus_to_virt(%pad)=%p\n",
-+ &urb->transfer_dma, buf);
-+ }
-+
-+ if (!(urb->transfer_flags & URB_NO_INTERRUPT))
-+ flags |= URB_GIVEBACK_ASAP;
-+ if (urb->transfer_flags & URB_ZERO_PACKET)
-+ flags |= URB_SEND_ZERO_PACKET;
-+
-+ dwc_otg_hcd_urb_set_params(dwc_otg_urb, urb, buf,
-+ urb->transfer_dma,
-+ urb->transfer_buffer_length,
-+ urb->setup_packet,
-+ urb->setup_dma, flags, urb->interval);
-+
-+ for (i = 0; i < urb->number_of_packets; ++i) {
-+ dwc_otg_hcd_urb_set_iso_desc_params(dwc_otg_urb, i,
-+ urb->
-+ iso_frame_desc[i].offset,
-+ urb->
-+ iso_frame_desc[i].length);
-+ }
-+
-+ DWC_SPINLOCK_IRQSAVE(dwc_otg_hcd->lock, &irqflags);
-+ urb->hcpriv = dwc_otg_urb;
-+#if USB_URB_EP_LINKING
-+ retval = usb_hcd_link_urb_to_ep(hcd, urb);
-+ if (0 == retval)
-+#endif
-+ {
-+ retval = dwc_otg_hcd_urb_enqueue(dwc_otg_hcd, dwc_otg_urb,
-+ /*(dwc_otg_qh_t **)*/
-+ ref_ep_hcpriv, 1);
-+ if (0 == retval) {
-+ if (alloc_bandwidth) {
-+ allocate_bus_bandwidth(hcd,
-+ dwc_otg_hcd_get_ep_bandwidth(
-+ dwc_otg_hcd, *ref_ep_hcpriv),
-+ urb);
-+ }
-+ } else {
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG dwc_otg_hcd_urb_enqueue failed rc %d\n", retval);
-+#if USB_URB_EP_LINKING
-+ usb_hcd_unlink_urb_from_ep(hcd, urb);
-+#endif
-+ DWC_FREE(dwc_otg_urb);
-+ urb->hcpriv = NULL;
-+ if (retval == -DWC_E_NO_DEVICE)
-+ retval = -ENODEV;
-+ }
-+ }
-+#if USB_URB_EP_LINKING
-+ else
-+ {
-+ DWC_FREE(dwc_otg_urb);
-+ urb->hcpriv = NULL;
-+ }
-+#endif
-+ DWC_SPINUNLOCK_IRQRESTORE(dwc_otg_hcd->lock, irqflags);
-+ return retval;
-+}
-+
-+/** Aborts/cancels a USB transfer request. Always returns 0 to indicate
-+ * success. */
-+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28)
-+static int dwc_otg_urb_dequeue(struct usb_hcd *hcd, struct urb *urb)
-+#else
-+static int dwc_otg_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status)
-+#endif
-+{
-+ dwc_irqflags_t flags;
-+ dwc_otg_hcd_t *dwc_otg_hcd;
-+ int rc;
-+
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD URB Dequeue\n");
-+
-+ dwc_otg_hcd = hcd_to_dwc_otg_hcd(hcd);
-+
-+#ifdef DEBUG
-+ if (CHK_DEBUG_LEVEL(DBG_HCDV | DBG_HCD_URB)) {
-+ dump_urb_info(urb, "dwc_otg_urb_dequeue");
-+ }
-+#endif
-+
-+ DWC_SPINLOCK_IRQSAVE(dwc_otg_hcd->lock, &flags);
-+ rc = usb_hcd_check_unlink_urb(hcd, urb, status);
-+ if (0 == rc) {
-+ if(urb->hcpriv != NULL) {
-+ dwc_otg_hcd_urb_dequeue(dwc_otg_hcd,
-+ (dwc_otg_hcd_urb_t *)urb->hcpriv);
-+
-+ DWC_FREE(urb->hcpriv);
-+ urb->hcpriv = NULL;
-+ }
-+ }
-+
-+ if (0 == rc) {
-+ /* Higher layer software sets URB status. */
-+#if USB_URB_EP_LINKING
-+ usb_hcd_unlink_urb_from_ep(hcd, urb);
-+#endif
-+ DWC_SPINUNLOCK_IRQRESTORE(dwc_otg_hcd->lock, flags);
-+
-+
-+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28)
-+ usb_hcd_giveback_urb(hcd, urb);
-+#else
-+ usb_hcd_giveback_urb(hcd, urb, status);
-+#endif
-+ if (CHK_DEBUG_LEVEL(DBG_HCDV | DBG_HCD_URB)) {
-+ DWC_PRINTF("Called usb_hcd_giveback_urb() \n");
-+ DWC_PRINTF(" 1urb->status = %d\n", urb->status);
-+ }
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD URB Dequeue OK\n");
-+ } else {
-+ DWC_SPINUNLOCK_IRQRESTORE(dwc_otg_hcd->lock, flags);
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD URB Dequeue failed - rc %d\n",
-+ rc);
-+ }
-+
-+ return rc;
-+}
-+
-+/* Frees resources in the DWC_otg controller related to a given endpoint. Also
-+ * clears state in the HCD related to the endpoint. Any URBs for the endpoint
-+ * must already be dequeued. */
-+static void endpoint_disable(struct usb_hcd *hcd, struct usb_host_endpoint *ep)
-+{
-+ dwc_otg_hcd_t *dwc_otg_hcd = hcd_to_dwc_otg_hcd(hcd);
-+
-+ DWC_DEBUGPL(DBG_HCD,
-+ "DWC OTG HCD EP DISABLE: _bEndpointAddress=0x%02x, "
-+ "endpoint=%d\n", ep->desc.bEndpointAddress,
-+ dwc_ep_addr_to_endpoint(ep->desc.bEndpointAddress));
-+ dwc_otg_hcd_endpoint_disable(dwc_otg_hcd, ep->hcpriv, 250);
-+ ep->hcpriv = NULL;
-+}
-+
-+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,30)
-+/* Resets endpoint specific parameter values, in current version used to reset
-+ * the data toggle(as a WA). This function can be called from usb_clear_halt routine */
-+static void endpoint_reset(struct usb_hcd *hcd, struct usb_host_endpoint *ep)
-+{
-+ dwc_irqflags_t flags;
-+ struct usb_device *udev = NULL;
-+ int epnum = usb_endpoint_num(&ep->desc);
-+ int is_out = usb_endpoint_dir_out(&ep->desc);
-+ int is_control = usb_endpoint_xfer_control(&ep->desc);
-+ dwc_otg_hcd_t *dwc_otg_hcd = hcd_to_dwc_otg_hcd(hcd);
-+ struct device *dev = DWC_OTG_OS_GETDEV(dwc_otg_hcd->otg_dev->os_dep);
-+
-+ if (dev)
-+ udev = to_usb_device(dev);
-+ else
-+ return;
-+
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD EP RESET: Endpoint Num=0x%02d\n", epnum);
-+
-+ DWC_SPINLOCK_IRQSAVE(dwc_otg_hcd->lock, &flags);
-+ usb_settoggle(udev, epnum, is_out, 0);
-+ if (is_control)
-+ usb_settoggle(udev, epnum, !is_out, 0);
-+
-+ if (ep->hcpriv) {
-+ dwc_otg_hcd_endpoint_reset(dwc_otg_hcd, ep->hcpriv);
-+ }
-+ DWC_SPINUNLOCK_IRQRESTORE(dwc_otg_hcd->lock, flags);
-+}
-+#endif
-+
-+/** Handles host mode interrupts for the DWC_otg controller. Returns IRQ_NONE if
-+ * there was no interrupt to handle. Returns IRQ_HANDLED if there was a valid
-+ * interrupt.
-+ *
-+ * This function is called by the USB core when an interrupt occurs */
-+static irqreturn_t dwc_otg_hcd_irq(struct usb_hcd *hcd)
-+{
-+ dwc_otg_hcd_t *dwc_otg_hcd = hcd_to_dwc_otg_hcd(hcd);
-+ int32_t retval = dwc_otg_hcd_handle_intr(dwc_otg_hcd);
-+ if (retval != 0) {
-+ S3C2410X_CLEAR_EINTPEND();
-+ }
-+ return IRQ_RETVAL(retval);
-+}
-+
-+/** Creates Status Change bitmap for the root hub and root port. The bitmap is
-+ * returned in buf. Bit 0 is the status change indicator for the root hub. Bit 1
-+ * is the status change indicator for the single root port. Returns 1 if either
-+ * change indicator is 1, otherwise returns 0. */
-+int hub_status_data(struct usb_hcd *hcd, char *buf)
-+{
-+ dwc_otg_hcd_t *dwc_otg_hcd = hcd_to_dwc_otg_hcd(hcd);
-+
-+ buf[0] = 0;
-+ buf[0] |= (dwc_otg_hcd_is_status_changed(dwc_otg_hcd, 1)) << 1;
-+
-+ return (buf[0] != 0);
-+}
-+
-+/** Handles hub class-specific requests. */
-+int hub_control(struct usb_hcd *hcd,
-+ u16 typeReq, u16 wValue, u16 wIndex, char *buf, u16 wLength)
-+{
-+ int retval;
-+
-+ retval = dwc_otg_hcd_hub_control(hcd_to_dwc_otg_hcd(hcd),
-+ typeReq, wValue, wIndex, buf, wLength);
-+
-+ switch (retval) {
-+ case -DWC_E_INVALID:
-+ retval = -EINVAL;
-+ break;
-+ }
-+
-+ return retval;
-+}
-+
-+#endif /* DWC_DEVICE_ONLY */
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_hcd_queue.c
-@@ -0,0 +1,957 @@
-+/* ==========================================================================
-+ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_hcd_queue.c $
-+ * $Revision: #44 $
-+ * $Date: 2011/10/26 $
-+ * $Change: 1873028 $
-+ *
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+#ifndef DWC_DEVICE_ONLY
-+
-+/**
-+ * @file
-+ *
-+ * This file contains the functions to manage Queue Heads and Queue
-+ * Transfer Descriptors.
-+ */
-+
-+#include "dwc_otg_hcd.h"
-+#include "dwc_otg_regs.h"
-+
-+extern bool microframe_schedule;
-+
-+/**
-+ * Free each QTD in the QH's QTD-list then free the QH. QH should already be
-+ * removed from a list. QTD list should already be empty if called from URB
-+ * Dequeue.
-+ *
-+ * @param hcd HCD instance.
-+ * @param qh The QH to free.
-+ */
-+void dwc_otg_hcd_qh_free(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh)
-+{
-+ dwc_otg_qtd_t *qtd, *qtd_tmp;
-+ dwc_irqflags_t flags;
-+
-+ /* Free each QTD in the QTD list */
-+ DWC_SPINLOCK_IRQSAVE(hcd->lock, &flags);
-+ DWC_CIRCLEQ_FOREACH_SAFE(qtd, qtd_tmp, &qh->qtd_list, qtd_list_entry) {
-+ DWC_CIRCLEQ_REMOVE(&qh->qtd_list, qtd, qtd_list_entry);
-+ dwc_otg_hcd_qtd_free(qtd);
-+ }
-+
-+ if (hcd->core_if->dma_desc_enable) {
-+ dwc_otg_hcd_qh_free_ddma(hcd, qh);
-+ } else if (qh->dw_align_buf) {
-+ uint32_t buf_size;
-+ if (qh->ep_type == UE_ISOCHRONOUS) {
-+ buf_size = 4096;
-+ } else {
-+ buf_size = hcd->core_if->core_params->max_transfer_size;
-+ }
-+ DWC_DMA_FREE(buf_size, qh->dw_align_buf, qh->dw_align_buf_dma);
-+ }
-+
-+ DWC_FREE(qh);
-+ DWC_SPINUNLOCK_IRQRESTORE(hcd->lock, flags);
-+ return;
-+}
-+
-+#define BitStuffTime(bytecount) ((8 * 7* bytecount) / 6)
-+#define HS_HOST_DELAY 5 /* nanoseconds */
-+#define FS_LS_HOST_DELAY 1000 /* nanoseconds */
-+#define HUB_LS_SETUP 333 /* nanoseconds */
-+#define NS_TO_US(ns) ((ns + 500) / 1000)
-+ /* convert & round nanoseconds to microseconds */
-+
-+static uint32_t calc_bus_time(int speed, int is_in, int is_isoc, int bytecount)
-+{
-+ unsigned long retval;
-+
-+ switch (speed) {
-+ case USB_SPEED_HIGH:
-+ if (is_isoc) {
-+ retval =
-+ ((38 * 8 * 2083) +
-+ (2083 * (3 + BitStuffTime(bytecount)))) / 1000 +
-+ HS_HOST_DELAY;
-+ } else {
-+ retval =
-+ ((55 * 8 * 2083) +
-+ (2083 * (3 + BitStuffTime(bytecount)))) / 1000 +
-+ HS_HOST_DELAY;
-+ }
-+ break;
-+ case USB_SPEED_FULL:
-+ if (is_isoc) {
-+ retval =
-+ (8354 * (31 + 10 * BitStuffTime(bytecount))) / 1000;
-+ if (is_in) {
-+ retval = 7268 + FS_LS_HOST_DELAY + retval;
-+ } else {
-+ retval = 6265 + FS_LS_HOST_DELAY + retval;
-+ }
-+ } else {
-+ retval =
-+ (8354 * (31 + 10 * BitStuffTime(bytecount))) / 1000;
-+ retval = 9107 + FS_LS_HOST_DELAY + retval;
-+ }
-+ break;
-+ case USB_SPEED_LOW:
-+ if (is_in) {
-+ retval =
-+ (67667 * (31 + 10 * BitStuffTime(bytecount))) /
-+ 1000;
-+ retval =
-+ 64060 + (2 * HUB_LS_SETUP) + FS_LS_HOST_DELAY +
-+ retval;
-+ } else {
-+ retval =
-+ (66700 * (31 + 10 * BitStuffTime(bytecount))) /
-+ 1000;
-+ retval =
-+ 64107 + (2 * HUB_LS_SETUP) + FS_LS_HOST_DELAY +
-+ retval;
-+ }
-+ break;
-+ default:
-+ DWC_WARN("Unknown device speed\n");
-+ retval = -1;
-+ }
-+
-+ return NS_TO_US(retval);
-+}
-+
-+/**
-+ * Initializes a QH structure.
-+ *
-+ * @param hcd The HCD state structure for the DWC OTG controller.
-+ * @param qh The QH to init.
-+ * @param urb Holds the information about the device/endpoint that we need
-+ * to initialize the QH.
-+ */
-+#define SCHEDULE_SLOP 10
-+void qh_init(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh, dwc_otg_hcd_urb_t * urb)
-+{
-+ char *speed, *type;
-+ int dev_speed;
-+ uint32_t hub_addr, hub_port;
-+
-+ dwc_memset(qh, 0, sizeof(dwc_otg_qh_t));
-+
-+ /* Initialize QH */
-+ qh->ep_type = dwc_otg_hcd_get_pipe_type(&urb->pipe_info);
-+ qh->ep_is_in = dwc_otg_hcd_is_pipe_in(&urb->pipe_info) ? 1 : 0;
-+
-+ qh->data_toggle = DWC_OTG_HC_PID_DATA0;
-+ qh->maxp = dwc_otg_hcd_get_mps(&urb->pipe_info);
-+ DWC_CIRCLEQ_INIT(&qh->qtd_list);
-+ DWC_LIST_INIT(&qh->qh_list_entry);
-+ qh->channel = NULL;
-+
-+ /* FS/LS Enpoint on HS Hub
-+ * NOT virtual root hub */
-+ dev_speed = hcd->fops->speed(hcd, urb->priv);
-+
-+ hcd->fops->hub_info(hcd, urb->priv, &hub_addr, &hub_port);
-+ qh->do_split = 0;
-+ if (microframe_schedule)
-+ qh->speed = dev_speed;
-+
-+ qh->nak_frame = 0xffff;
-+
-+ if (((dev_speed == USB_SPEED_LOW) ||
-+ (dev_speed == USB_SPEED_FULL)) &&
-+ (hub_addr != 0 && hub_addr != 1)) {
-+ DWC_DEBUGPL(DBG_HCD,
-+ "QH init: EP %d: TT found at hub addr %d, for port %d\n",
-+ dwc_otg_hcd_get_ep_num(&urb->pipe_info), hub_addr,
-+ hub_port);
-+ qh->do_split = 1;
-+ qh->skip_count = 0;
-+ }
-+
-+ if (qh->ep_type == UE_INTERRUPT || qh->ep_type == UE_ISOCHRONOUS) {
-+ /* Compute scheduling parameters once and save them. */
-+ hprt0_data_t hprt;
-+
-+ /** @todo Account for split transfers in the bus time. */
-+ int bytecount =
-+ dwc_hb_mult(qh->maxp) * dwc_max_packet(qh->maxp);
-+
-+ qh->usecs =
-+ calc_bus_time((qh->do_split ? USB_SPEED_HIGH : dev_speed),
-+ qh->ep_is_in, (qh->ep_type == UE_ISOCHRONOUS),
-+ bytecount);
-+ /* Start in a slightly future (micro)frame. */
-+ qh->sched_frame = dwc_frame_num_inc(hcd->frame_number,
-+ SCHEDULE_SLOP);
-+ qh->interval = urb->interval;
-+
-+#if 0
-+ /* Increase interrupt polling rate for debugging. */
-+ if (qh->ep_type == UE_INTERRUPT) {
-+ qh->interval = 8;
-+ }
-+#endif
-+ hprt.d32 = DWC_READ_REG32(hcd->core_if->host_if->hprt0);
-+ if ((hprt.b.prtspd == DWC_HPRT0_PRTSPD_HIGH_SPEED) &&
-+ ((dev_speed == USB_SPEED_LOW) ||
-+ (dev_speed == USB_SPEED_FULL))) {
-+ qh->interval *= 8;
-+ qh->sched_frame |= 0x7;
-+ qh->start_split_frame = qh->sched_frame;
-+ }
-+
-+ }
-+
-+ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD QH Initialized\n");
-+ DWC_DEBUGPL(DBG_HCDV, "DWC OTG HCD QH - qh = %p\n", qh);
-+ DWC_DEBUGPL(DBG_HCDV, "DWC OTG HCD QH - Device Address = %d\n",
-+ dwc_otg_hcd_get_dev_addr(&urb->pipe_info));
-+ DWC_DEBUGPL(DBG_HCDV, "DWC OTG HCD QH - Endpoint %d, %s\n",
-+ dwc_otg_hcd_get_ep_num(&urb->pipe_info),
-+ dwc_otg_hcd_is_pipe_in(&urb->pipe_info) ? "IN" : "OUT");
-+ switch (dev_speed) {
-+ case USB_SPEED_LOW:
-+ qh->dev_speed = DWC_OTG_EP_SPEED_LOW;
-+ speed = "low";
-+ break;
-+ case USB_SPEED_FULL:
-+ qh->dev_speed = DWC_OTG_EP_SPEED_FULL;
-+ speed = "full";
-+ break;
-+ case USB_SPEED_HIGH:
-+ qh->dev_speed = DWC_OTG_EP_SPEED_HIGH;
-+ speed = "high";
-+ break;
-+ default:
-+ speed = "?";
-+ break;
-+ }
-+ DWC_DEBUGPL(DBG_HCDV, "DWC OTG HCD QH - Speed = %s\n", speed);
-+
-+ switch (qh->ep_type) {
-+ case UE_ISOCHRONOUS:
-+ type = "isochronous";
-+ break;
-+ case UE_INTERRUPT:
-+ type = "interrupt";
-+ break;
-+ case UE_CONTROL:
-+ type = "control";
-+ break;
-+ case UE_BULK:
-+ type = "bulk";
-+ break;
-+ default:
-+ type = "?";
-+ break;
-+ }
-+
-+ DWC_DEBUGPL(DBG_HCDV, "DWC OTG HCD QH - Type = %s\n", type);
-+
-+#ifdef DEBUG
-+ if (qh->ep_type == UE_INTERRUPT) {
-+ DWC_DEBUGPL(DBG_HCDV, "DWC OTG HCD QH - usecs = %d\n",
-+ qh->usecs);
-+ DWC_DEBUGPL(DBG_HCDV, "DWC OTG HCD QH - interval = %d\n",
-+ qh->interval);
-+ }
-+#endif
-+
-+}
-+
-+/**
-+ * This function allocates and initializes a QH.
-+ *
-+ * @param hcd The HCD state structure for the DWC OTG controller.
-+ * @param urb Holds the information about the device/endpoint that we need
-+ * to initialize the QH.
-+ * @param atomic_alloc Flag to do atomic allocation if needed
-+ *
-+ * @return Returns pointer to the newly allocated QH, or NULL on error. */
-+dwc_otg_qh_t *dwc_otg_hcd_qh_create(dwc_otg_hcd_t * hcd,
-+ dwc_otg_hcd_urb_t * urb, int atomic_alloc)
-+{
-+ dwc_otg_qh_t *qh;
-+
-+ /* Allocate memory */
-+ /** @todo add memflags argument */
-+ qh = dwc_otg_hcd_qh_alloc(atomic_alloc);
-+ if (qh == NULL) {
-+ DWC_ERROR("qh allocation failed");
-+ return NULL;
-+ }
-+
-+ qh_init(hcd, qh, urb);
-+
-+ if (hcd->core_if->dma_desc_enable
-+ && (dwc_otg_hcd_qh_init_ddma(hcd, qh) < 0)) {
-+ dwc_otg_hcd_qh_free(hcd, qh);
-+ return NULL;
-+ }
-+
-+ return qh;
-+}
-+
-+/* microframe_schedule=0 start */
-+
-+/**
-+ * Checks that a channel is available for a periodic transfer.
-+ *
-+ * @return 0 if successful, negative error code otherise.
-+ */
-+static int periodic_channel_available(dwc_otg_hcd_t * hcd)
-+{
-+ /*
-+ * Currently assuming that there is a dedicated host channnel for each
-+ * periodic transaction plus at least one host channel for
-+ * non-periodic transactions.
-+ */
-+ int status;
-+ int num_channels;
-+
-+ num_channels = hcd->core_if->core_params->host_channels;
-+ if ((hcd->periodic_channels + hcd->non_periodic_channels < num_channels)
-+ && (hcd->periodic_channels < num_channels - 1)) {
-+ status = 0;
-+ } else {
-+ DWC_INFO("%s: Total channels: %d, Periodic: %d, Non-periodic: %d\n",
-+ __func__, num_channels, hcd->periodic_channels, hcd->non_periodic_channels); //NOTICE
-+ status = -DWC_E_NO_SPACE;
-+ }
-+
-+ return status;
-+}
-+
-+/**
-+ * Checks that there is sufficient bandwidth for the specified QH in the
-+ * periodic schedule. For simplicity, this calculation assumes that all the
-+ * transfers in the periodic schedule may occur in the same (micro)frame.
-+ *
-+ * @param hcd The HCD state structure for the DWC OTG controller.
-+ * @param qh QH containing periodic bandwidth required.
-+ *
-+ * @return 0 if successful, negative error code otherwise.
-+ */
-+static int check_periodic_bandwidth(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh)
-+{
-+ int status;
-+ int16_t max_claimed_usecs;
-+
-+ status = 0;
-+
-+ if ((qh->dev_speed == DWC_OTG_EP_SPEED_HIGH) || qh->do_split) {
-+ /*
-+ * High speed mode.
-+ * Max periodic usecs is 80% x 125 usec = 100 usec.
-+ */
-+
-+ max_claimed_usecs = 100 - qh->usecs;
-+ } else {
-+ /*
-+ * Full speed mode.
-+ * Max periodic usecs is 90% x 1000 usec = 900 usec.
-+ */
-+ max_claimed_usecs = 900 - qh->usecs;
-+ }
-+
-+ if (hcd->periodic_usecs > max_claimed_usecs) {
-+ DWC_INFO("%s: already claimed usecs %d, required usecs %d\n", __func__, hcd->periodic_usecs, qh->usecs); //NOTICE
-+ status = -DWC_E_NO_SPACE;
-+ }
-+
-+ return status;
-+}
-+
-+/* microframe_schedule=0 end */
-+
-+/**
-+ * Microframe scheduler
-+ * track the total use in hcd->frame_usecs
-+ * keep each qh use in qh->frame_usecs
-+ * when surrendering the qh then donate the time back
-+ */
-+const unsigned short max_uframe_usecs[]={ 100, 100, 100, 100, 100, 100, 30, 0 };
-+
-+/*
-+ * called from dwc_otg_hcd.c:dwc_otg_hcd_init
-+ */
-+int init_hcd_usecs(dwc_otg_hcd_t *_hcd)
-+{
-+ int i;
-+ for (i=0; i<8; i++) {
-+ _hcd->frame_usecs[i] = max_uframe_usecs[i];
-+ }
-+ return 0;
-+}
-+
-+static int find_single_uframe(dwc_otg_hcd_t * _hcd, dwc_otg_qh_t * _qh)
-+{
-+ int i;
-+ unsigned short utime;
-+ int t_left;
-+ int ret;
-+ int done;
-+
-+ ret = -1;
-+ utime = _qh->usecs;
-+ t_left = utime;
-+ i = 0;
-+ done = 0;
-+ while (done == 0) {
-+ /* At the start _hcd->frame_usecs[i] = max_uframe_usecs[i]; */
-+ if (utime <= _hcd->frame_usecs[i]) {
-+ _hcd->frame_usecs[i] -= utime;
-+ _qh->frame_usecs[i] += utime;
-+ t_left -= utime;
-+ ret = i;
-+ done = 1;
-+ return ret;
-+ } else {
-+ i++;
-+ if (i == 8) {
-+ done = 1;
-+ ret = -1;
-+ }
-+ }
-+ }
-+ return ret;
-+ }
-+
-+/*
-+ * use this for FS apps that can span multiple uframes
-+ */
-+static int find_multi_uframe(dwc_otg_hcd_t * _hcd, dwc_otg_qh_t * _qh)
-+{
-+ int i;
-+ int j;
-+ unsigned short utime;
-+ int t_left;
-+ int ret;
-+ int done;
-+ unsigned short xtime;
-+
-+ ret = -1;
-+ utime = _qh->usecs;
-+ t_left = utime;
-+ i = 0;
-+ done = 0;
-+loop:
-+ while (done == 0) {
-+ if(_hcd->frame_usecs[i] <= 0) {
-+ i++;
-+ if (i == 8) {
-+ done = 1;
-+ ret = -1;
-+ }
-+ goto loop;
-+ }
-+
-+ /*
-+ * we need n consecutive slots
-+ * so use j as a start slot j plus j+1 must be enough time (for now)
-+ */
-+ xtime= _hcd->frame_usecs[i];
-+ for (j = i+1 ; j < 8 ; j++ ) {
-+ /*
-+ * if we add this frame remaining time to xtime we may
-+ * be OK, if not we need to test j for a complete frame
-+ */
-+ if ((xtime+_hcd->frame_usecs[j]) < utime) {
-+ if (_hcd->frame_usecs[j] < max_uframe_usecs[j]) {
-+ j = 8;
-+ ret = -1;
-+ continue;
-+ }
-+ }
-+ if (xtime >= utime) {
-+ ret = i;
-+ j = 8; /* stop loop with a good value ret */
-+ continue;
-+ }
-+ /* add the frame time to x time */
-+ xtime += _hcd->frame_usecs[j];
-+ /* we must have a fully available next frame or break */
-+ if ((xtime < utime)
-+ && (_hcd->frame_usecs[j] == max_uframe_usecs[j])) {
-+ ret = -1;
-+ j = 8; /* stop loop with a bad value ret */
-+ continue;
-+ }
-+ }
-+ if (ret >= 0) {
-+ t_left = utime;
-+ for (j = i; (t_left>0) && (j < 8); j++ ) {
-+ t_left -= _hcd->frame_usecs[j];
-+ if ( t_left <= 0 ) {
-+ _qh->frame_usecs[j] += _hcd->frame_usecs[j] + t_left;
-+ _hcd->frame_usecs[j]= -t_left;
-+ ret = i;
-+ done = 1;
-+ } else {
-+ _qh->frame_usecs[j] += _hcd->frame_usecs[j];
-+ _hcd->frame_usecs[j] = 0;
-+ }
-+ }
-+ } else {
-+ i++;
-+ if (i == 8) {
-+ done = 1;
-+ ret = -1;
-+ }
-+ }
-+ }
-+ return ret;
-+}
-+
-+static int find_uframe(dwc_otg_hcd_t * _hcd, dwc_otg_qh_t * _qh)
-+{
-+ int ret;
-+ ret = -1;
-+
-+ if (_qh->speed == USB_SPEED_HIGH) {
-+ /* if this is a hs transaction we need a full frame */
-+ ret = find_single_uframe(_hcd, _qh);
-+ } else {
-+ /* if this is a fs transaction we may need a sequence of frames */
-+ ret = find_multi_uframe(_hcd, _qh);
-+ }
-+ return ret;
-+}
-+
-+/**
-+ * Checks that the max transfer size allowed in a host channel is large enough
-+ * to handle the maximum data transfer in a single (micro)frame for a periodic
-+ * transfer.
-+ *
-+ * @param hcd The HCD state structure for the DWC OTG controller.
-+ * @param qh QH for a periodic endpoint.
-+ *
-+ * @return 0 if successful, negative error code otherwise.
-+ */
-+static int check_max_xfer_size(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh)
-+{
-+ int status;
-+ uint32_t max_xfer_size;
-+ uint32_t max_channel_xfer_size;
-+
-+ status = 0;
-+
-+ max_xfer_size = dwc_max_packet(qh->maxp) * dwc_hb_mult(qh->maxp);
-+ max_channel_xfer_size = hcd->core_if->core_params->max_transfer_size;
-+
-+ if (max_xfer_size > max_channel_xfer_size) {
-+ DWC_INFO("%s: Periodic xfer length %d > " "max xfer length for channel %d\n",
-+ __func__, max_xfer_size, max_channel_xfer_size); //NOTICE
-+ status = -DWC_E_NO_SPACE;
-+ }
-+
-+ return status;
-+}
-+
-+
-+
-+/**
-+ * Schedules an interrupt or isochronous transfer in the periodic schedule.
-+ *
-+ * @param hcd The HCD state structure for the DWC OTG controller.
-+ * @param qh QH for the periodic transfer. The QH should already contain the
-+ * scheduling information.
-+ *
-+ * @return 0 if successful, negative error code otherwise.
-+ */
-+static int schedule_periodic(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh)
-+{
-+ int status = 0;
-+
-+ if (microframe_schedule) {
-+ int frame;
-+ status = find_uframe(hcd, qh);
-+ frame = -1;
-+ if (status == 0) {
-+ frame = 7;
-+ } else {
-+ if (status > 0 )
-+ frame = status-1;
-+ }
-+
-+ /* Set the new frame up */
-+ if (frame > -1) {
-+ qh->sched_frame &= ~0x7;
-+ qh->sched_frame |= (frame & 7);
-+ }
-+
-+ if (status != -1)
-+ status = 0;
-+ } else {
-+ status = periodic_channel_available(hcd);
-+ if (status) {
-+ DWC_INFO("%s: No host channel available for periodic " "transfer.\n", __func__); //NOTICE
-+ return status;
-+ }
-+
-+ status = check_periodic_bandwidth(hcd, qh);
-+ }
-+ if (status) {
-+ DWC_INFO("%s: Insufficient periodic bandwidth for "
-+ "periodic transfer.\n", __func__);
-+ return status;
-+ }
-+ status = check_max_xfer_size(hcd, qh);
-+ if (status) {
-+ DWC_INFO("%s: Channel max transfer size too small "
-+ "for periodic transfer.\n", __func__);
-+ return status;
-+ }
-+
-+ if (hcd->core_if->dma_desc_enable) {
-+ /* Don't rely on SOF and start in ready schedule */
-+ DWC_LIST_INSERT_TAIL(&hcd->periodic_sched_ready, &qh->qh_list_entry);
-+ }
-+ else {
-+ if(fiq_enable && (DWC_LIST_EMPTY(&hcd->periodic_sched_inactive) || dwc_frame_num_le(qh->sched_frame, hcd->fiq_state->next_sched_frame)))
-+ {
-+ hcd->fiq_state->next_sched_frame = qh->sched_frame;
-+
-+ }
-+ /* Always start in the inactive schedule. */
-+ DWC_LIST_INSERT_TAIL(&hcd->periodic_sched_inactive, &qh->qh_list_entry);
-+ }
-+
-+ if (!microframe_schedule) {
-+ /* Reserve the periodic channel. */
-+ hcd->periodic_channels++;
-+ }
-+
-+ /* Update claimed usecs per (micro)frame. */
-+ hcd->periodic_usecs += qh->usecs;
-+
-+ return status;
-+}
-+
-+
-+/**
-+ * This function adds a QH to either the non periodic or periodic schedule if
-+ * it is not already in the schedule. If the QH is already in the schedule, no
-+ * action is taken.
-+ *
-+ * @return 0 if successful, negative error code otherwise.
-+ */
-+int dwc_otg_hcd_qh_add(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh)
-+{
-+ int status = 0;
-+ gintmsk_data_t intr_mask = {.d32 = 0 };
-+
-+ if (!DWC_LIST_EMPTY(&qh->qh_list_entry)) {
-+ /* QH already in a schedule. */
-+ return status;
-+ }
-+
-+ /* Add the new QH to the appropriate schedule */
-+ if (dwc_qh_is_non_per(qh)) {
-+ /* Always start in the inactive schedule. */
-+ DWC_LIST_INSERT_TAIL(&hcd->non_periodic_sched_inactive,
-+ &qh->qh_list_entry);
-+ //hcd->fiq_state->kick_np_queues = 1;
-+ } else {
-+ status = schedule_periodic(hcd, qh);
-+ if ( !hcd->periodic_qh_count ) {
-+ intr_mask.b.sofintr = 1;
-+ if (fiq_enable) {
-+ local_fiq_disable();
-+ fiq_fsm_spin_lock(&hcd->fiq_state->lock);
-+ DWC_MODIFY_REG32(&hcd->core_if->core_global_regs->gintmsk, intr_mask.d32, intr_mask.d32);
-+ fiq_fsm_spin_unlock(&hcd->fiq_state->lock);
-+ local_fiq_enable();
-+ } else {
-+ DWC_MODIFY_REG32(&hcd->core_if->core_global_regs->gintmsk, intr_mask.d32, intr_mask.d32);
-+ }
-+ }
-+ hcd->periodic_qh_count++;
-+ }
-+
-+ return status;
-+}
-+
-+/**
-+ * Removes an interrupt or isochronous transfer from the periodic schedule.
-+ *
-+ * @param hcd The HCD state structure for the DWC OTG controller.
-+ * @param qh QH for the periodic transfer.
-+ */
-+static void deschedule_periodic(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh)
-+{
-+ int i;
-+ DWC_LIST_REMOVE_INIT(&qh->qh_list_entry);
-+
-+ /* Update claimed usecs per (micro)frame. */
-+ hcd->periodic_usecs -= qh->usecs;
-+
-+ if (!microframe_schedule) {
-+ /* Release the periodic channel reservation. */
-+ hcd->periodic_channels--;
-+ } else {
-+ for (i = 0; i < 8; i++) {
-+ hcd->frame_usecs[i] += qh->frame_usecs[i];
-+ qh->frame_usecs[i] = 0;
-+ }
-+ }
-+}
-+
-+/**
-+ * Removes a QH from either the non-periodic or periodic schedule. Memory is
-+ * not freed.
-+ *
-+ * @param hcd The HCD state structure.
-+ * @param qh QH to remove from schedule. */
-+void dwc_otg_hcd_qh_remove(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh)
-+{
-+ gintmsk_data_t intr_mask = {.d32 = 0 };
-+
-+ if (DWC_LIST_EMPTY(&qh->qh_list_entry)) {
-+ /* QH is not in a schedule. */
-+ return;
-+ }
-+
-+ if (dwc_qh_is_non_per(qh)) {
-+ if (hcd->non_periodic_qh_ptr == &qh->qh_list_entry) {
-+ hcd->non_periodic_qh_ptr =
-+ hcd->non_periodic_qh_ptr->next;
-+ }
-+ DWC_LIST_REMOVE_INIT(&qh->qh_list_entry);
-+ //if (!DWC_LIST_EMPTY(&hcd->non_periodic_sched_inactive))
-+ // hcd->fiq_state->kick_np_queues = 1;
-+ } else {
-+ deschedule_periodic(hcd, qh);
-+ hcd->periodic_qh_count--;
-+ if( !hcd->periodic_qh_count && !fiq_fsm_enable ) {
-+ intr_mask.b.sofintr = 1;
-+ if (fiq_enable) {
-+ local_fiq_disable();
-+ fiq_fsm_spin_lock(&hcd->fiq_state->lock);
-+ DWC_MODIFY_REG32(&hcd->core_if->core_global_regs->gintmsk, intr_mask.d32, 0);
-+ fiq_fsm_spin_unlock(&hcd->fiq_state->lock);
-+ local_fiq_enable();
-+ } else {
-+ DWC_MODIFY_REG32(&hcd->core_if->core_global_regs->gintmsk, intr_mask.d32, 0);
-+ }
-+ }
-+ }
-+}
-+
-+/**
-+ * Deactivates a QH. For non-periodic QHs, removes the QH from the active
-+ * non-periodic schedule. The QH is added to the inactive non-periodic
-+ * schedule if any QTDs are still attached to the QH.
-+ *
-+ * For periodic QHs, the QH is removed from the periodic queued schedule. If
-+ * there are any QTDs still attached to the QH, the QH is added to either the
-+ * periodic inactive schedule or the periodic ready schedule and its next
-+ * scheduled frame is calculated. The QH is placed in the ready schedule if
-+ * the scheduled frame has been reached already. Otherwise it's placed in the
-+ * inactive schedule. If there are no QTDs attached to the QH, the QH is
-+ * completely removed from the periodic schedule.
-+ */
-+void dwc_otg_hcd_qh_deactivate(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh,
-+ int sched_next_periodic_split)
-+{
-+ if (dwc_qh_is_non_per(qh)) {
-+ dwc_otg_hcd_qh_remove(hcd, qh);
-+ if (!DWC_CIRCLEQ_EMPTY(&qh->qtd_list)) {
-+ /* Add back to inactive non-periodic schedule. */
-+ dwc_otg_hcd_qh_add(hcd, qh);
-+ //hcd->fiq_state->kick_np_queues = 1;
-+ }
-+ } else {
-+ uint16_t frame_number = dwc_otg_hcd_get_frame_number(hcd);
-+
-+ if (qh->do_split) {
-+ /* Schedule the next continuing periodic split transfer */
-+ if (sched_next_periodic_split) {
-+
-+ qh->sched_frame = frame_number;
-+
-+ if (dwc_frame_num_le(frame_number,
-+ dwc_frame_num_inc
-+ (qh->start_split_frame,
-+ 1))) {
-+ /*
-+ * Allow one frame to elapse after start
-+ * split microframe before scheduling
-+ * complete split, but DONT if we are
-+ * doing the next start split in the
-+ * same frame for an ISOC out.
-+ */
-+ if ((qh->ep_type != UE_ISOCHRONOUS) ||
-+ (qh->ep_is_in != 0)) {
-+ qh->sched_frame =
-+ dwc_frame_num_inc(qh->sched_frame, 1);
-+ }
-+ }
-+ } else {
-+ qh->sched_frame =
-+ dwc_frame_num_inc(qh->start_split_frame,
-+ qh->interval);
-+ if (dwc_frame_num_le
-+ (qh->sched_frame, frame_number)) {
-+ qh->sched_frame = frame_number;
-+ }
-+ qh->sched_frame |= 0x7;
-+ qh->start_split_frame = qh->sched_frame;
-+ }
-+ } else {
-+ qh->sched_frame =
-+ dwc_frame_num_inc(qh->sched_frame, qh->interval);
-+ if (dwc_frame_num_le(qh->sched_frame, frame_number)) {
-+ qh->sched_frame = frame_number;
-+ }
-+ }
-+
-+ if (DWC_CIRCLEQ_EMPTY(&qh->qtd_list)) {
-+ dwc_otg_hcd_qh_remove(hcd, qh);
-+ } else {
-+ /*
-+ * Remove from periodic_sched_queued and move to
-+ * appropriate queue.
-+ */
-+ if ((microframe_schedule && dwc_frame_num_le(qh->sched_frame, frame_number)) ||
-+ (!microframe_schedule && qh->sched_frame == frame_number)) {
-+ DWC_LIST_MOVE_HEAD(&hcd->periodic_sched_ready,
-+ &qh->qh_list_entry);
-+ } else {
-+ if(fiq_enable && !dwc_frame_num_le(hcd->fiq_state->next_sched_frame, qh->sched_frame))
-+ {
-+ hcd->fiq_state->next_sched_frame = qh->sched_frame;
-+ }
-+
-+ DWC_LIST_MOVE_HEAD
-+ (&hcd->periodic_sched_inactive,
-+ &qh->qh_list_entry);
-+ }
-+ }
-+ }
-+}
-+
-+/**
-+ * This function allocates and initializes a QTD.
-+ *
-+ * @param urb The URB to create a QTD from. Each URB-QTD pair will end up
-+ * pointing to each other so each pair should have a unique correlation.
-+ * @param atomic_alloc Flag to do atomic alloc if needed
-+ *
-+ * @return Returns pointer to the newly allocated QTD, or NULL on error. */
-+dwc_otg_qtd_t *dwc_otg_hcd_qtd_create(dwc_otg_hcd_urb_t * urb, int atomic_alloc)
-+{
-+ dwc_otg_qtd_t *qtd;
-+
-+ qtd = dwc_otg_hcd_qtd_alloc(atomic_alloc);
-+ if (qtd == NULL) {
-+ return NULL;
-+ }
-+
-+ dwc_otg_hcd_qtd_init(qtd, urb);
-+ return qtd;
-+}
-+
-+/**
-+ * Initializes a QTD structure.
-+ *
-+ * @param qtd The QTD to initialize.
-+ * @param urb The URB to use for initialization. */
-+void dwc_otg_hcd_qtd_init(dwc_otg_qtd_t * qtd, dwc_otg_hcd_urb_t * urb)
-+{
-+ dwc_memset(qtd, 0, sizeof(dwc_otg_qtd_t));
-+ qtd->urb = urb;
-+ if (dwc_otg_hcd_get_pipe_type(&urb->pipe_info) == UE_CONTROL) {
-+ /*
-+ * The only time the QTD data toggle is used is on the data
-+ * phase of control transfers. This phase always starts with
-+ * DATA1.
-+ */
-+ qtd->data_toggle = DWC_OTG_HC_PID_DATA1;
-+ qtd->control_phase = DWC_OTG_CONTROL_SETUP;
-+ }
-+
-+ /* start split */
-+ qtd->complete_split = 0;
-+ qtd->isoc_split_pos = DWC_HCSPLIT_XACTPOS_ALL;
-+ qtd->isoc_split_offset = 0;
-+ qtd->in_process = 0;
-+
-+ /* Store the qtd ptr in the urb to reference what QTD. */
-+ urb->qtd = qtd;
-+ return;
-+}
-+
-+/**
-+ * This function adds a QTD to the QTD-list of a QH. It will find the correct
-+ * QH to place the QTD into. If it does not find a QH, then it will create a
-+ * new QH. If the QH to which the QTD is added is not currently scheduled, it
-+ * is placed into the proper schedule based on its EP type.
-+ * HCD lock must be held and interrupts must be disabled on entry
-+ *
-+ * @param[in] qtd The QTD to add
-+ * @param[in] hcd The DWC HCD structure
-+ * @param[out] qh out parameter to return queue head
-+ * @param atomic_alloc Flag to do atomic alloc if needed
-+ *
-+ * @return 0 if successful, negative error code otherwise.
-+ */
-+int dwc_otg_hcd_qtd_add(dwc_otg_qtd_t * qtd,
-+ dwc_otg_hcd_t * hcd, dwc_otg_qh_t ** qh, int atomic_alloc)
-+{
-+ int retval = 0;
-+ dwc_otg_hcd_urb_t *urb = qtd->urb;
-+
-+ /*
-+ * Get the QH which holds the QTD-list to insert to. Create QH if it
-+ * doesn't exist.
-+ */
-+ if (*qh == NULL) {
-+ *qh = dwc_otg_hcd_qh_create(hcd, urb, atomic_alloc);
-+ if (*qh == NULL) {
-+ retval = -DWC_E_NO_MEMORY;
-+ goto done;
-+ } else {
-+ if (fiq_enable)
-+ hcd->fiq_state->kick_np_queues = 1;
-+ }
-+ }
-+ retval = dwc_otg_hcd_qh_add(hcd, *qh);
-+ if (retval == 0) {
-+ DWC_CIRCLEQ_INSERT_TAIL(&((*qh)->qtd_list), qtd,
-+ qtd_list_entry);
-+ qtd->qh = *qh;
-+ }
-+done:
-+
-+ return retval;
-+}
-+
-+#endif /* DWC_DEVICE_ONLY */
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_os_dep.h
-@@ -0,0 +1,188 @@
-+#ifndef _DWC_OS_DEP_H_
-+#define _DWC_OS_DEP_H_
-+
-+/**
-+ * @file
-+ *
-+ * This file contains OS dependent structures.
-+ *
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+#include <linux/moduleparam.h>
-+#include <linux/init.h>
-+#include <linux/device.h>
-+#include <linux/errno.h>
-+#include <linux/types.h>
-+#include <linux/slab.h>
-+#include <linux/list.h>
-+#include <linux/interrupt.h>
-+#include <linux/ctype.h>
-+#include <linux/string.h>
-+#include <linux/dma-mapping.h>
-+#include <linux/jiffies.h>
-+#include <linux/delay.h>
-+#include <linux/timer.h>
-+#include <linux/workqueue.h>
-+#include <linux/stat.h>
-+#include <linux/pci.h>
-+
-+#include <linux/version.h>
-+
-+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,20)
-+# include <linux/irq.h>
-+#endif
-+
-+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,21)
-+# include <linux/usb/ch9.h>
-+#else
-+# include <linux/usb_ch9.h>
-+#endif
-+
-+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,24)
-+# include <linux/usb/gadget.h>
-+#else
-+# include <linux/usb_gadget.h>
-+#endif
-+
-+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,20)
-+# include <asm/irq.h>
-+#endif
-+
-+#ifdef PCI_INTERFACE
-+# include <asm/io.h>
-+#endif
-+
-+#ifdef LM_INTERFACE
-+# include <asm/unaligned.h>
-+# include <asm/sizes.h>
-+# include <asm/param.h>
-+# include <asm/io.h>
-+# if (LINUX_VERSION_CODE < KERNEL_VERSION(2,6,30))
-+# include <asm/arch/hardware.h>
-+# include <asm/arch/lm.h>
-+# include <asm/arch/irqs.h>
-+# include <asm/arch/regs-irq.h>
-+# else
-+/* in 2.6.31, at least, we seem to have lost the generic LM infrastructure -
-+ here we assume that the machine architecture provides definitions
-+ in its own header
-+*/
-+# include <mach/lm.h>
-+# include <mach/hardware.h>
-+# endif
-+#endif
-+
-+#ifdef PLATFORM_INTERFACE
-+#include <linux/platform_device.h>
-+#include <asm/mach/map.h>
-+#endif
-+
-+/** The OS page size */
-+#define DWC_OS_PAGE_SIZE PAGE_SIZE
-+
-+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,14)
-+typedef int gfp_t;
-+#endif
-+
-+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,18)
-+# define IRQF_SHARED SA_SHIRQ
-+#endif
-+
-+typedef struct os_dependent {
-+ /** Base address returned from ioremap() */
-+ void *base;
-+
-+ /** Register offset for Diagnostic API */
-+ uint32_t reg_offset;
-+
-+ /** Base address for MPHI peripheral */
-+ void *mphi_base;
-+
-+#ifdef LM_INTERFACE
-+ struct lm_device *lmdev;
-+#elif defined(PCI_INTERFACE)
-+ struct pci_dev *pcidev;
-+
-+ /** Start address of a PCI region */
-+ resource_size_t rsrc_start;
-+
-+ /** Length address of a PCI region */
-+ resource_size_t rsrc_len;
-+#elif defined(PLATFORM_INTERFACE)
-+ struct platform_device *platformdev;
-+#endif
-+
-+} os_dependent_t;
-+
-+#ifdef __cplusplus
-+}
-+#endif
-+
-+
-+
-+/* Type for the our device on the chosen bus */
-+#if defined(LM_INTERFACE)
-+typedef struct lm_device dwc_bus_dev_t;
-+#elif defined(PCI_INTERFACE)
-+typedef struct pci_dev dwc_bus_dev_t;
-+#elif defined(PLATFORM_INTERFACE)
-+typedef struct platform_device dwc_bus_dev_t;
-+#endif
-+
-+/* Helper macro to retrieve drvdata from the device on the chosen bus */
-+#if defined(LM_INTERFACE)
-+#define DWC_OTG_BUSDRVDATA(_dev) lm_get_drvdata(_dev)
-+#elif defined(PCI_INTERFACE)
-+#define DWC_OTG_BUSDRVDATA(_dev) pci_get_drvdata(_dev)
-+#elif defined(PLATFORM_INTERFACE)
-+#define DWC_OTG_BUSDRVDATA(_dev) platform_get_drvdata(_dev)
-+#endif
-+
-+/**
-+ * Helper macro returning the otg_device structure of a given struct device
-+ *
-+ * c.f. static dwc_otg_device_t *dwc_otg_drvdev(struct device *_dev)
-+ */
-+#ifdef LM_INTERFACE
-+#define DWC_OTG_GETDRVDEV(_var, _dev) do { \
-+ struct lm_device *lm_dev = \
-+ container_of(_dev, struct lm_device, dev); \
-+ _var = lm_get_drvdata(lm_dev); \
-+ } while (0)
-+
-+#elif defined(PCI_INTERFACE)
-+#define DWC_OTG_GETDRVDEV(_var, _dev) do { \
-+ _var = dev_get_drvdata(_dev); \
-+ } while (0)
-+
-+#elif defined(PLATFORM_INTERFACE)
-+#define DWC_OTG_GETDRVDEV(_var, _dev) do { \
-+ struct platform_device *platform_dev = \
-+ container_of(_dev, struct platform_device, dev); \
-+ _var = platform_get_drvdata(platform_dev); \
-+ } while (0)
-+#endif
-+
-+
-+/**
-+ * Helper macro returning the struct dev of the given struct os_dependent
-+ *
-+ * c.f. static struct device *dwc_otg_getdev(struct os_dependent *osdep)
-+ */
-+#ifdef LM_INTERFACE
-+#define DWC_OTG_OS_GETDEV(_osdep) \
-+ ((_osdep).lmdev == NULL? NULL: &(_osdep).lmdev->dev)
-+#elif defined(PCI_INTERFACE)
-+#define DWC_OTG_OS_GETDEV(_osdep) \
-+ ((_osdep).pci_dev == NULL? NULL: &(_osdep).pci_dev->dev)
-+#elif defined(PLATFORM_INTERFACE)
-+#define DWC_OTG_OS_GETDEV(_osdep) \
-+ ((_osdep).platformdev == NULL? NULL: &(_osdep).platformdev->dev)
-+#endif
-+
-+
-+
-+
-+#endif /* _DWC_OS_DEP_H_ */
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_pcd.c
-@@ -0,0 +1,2712 @@
-+/* ==========================================================================
-+ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_pcd.c $
-+ * $Revision: #101 $
-+ * $Date: 2012/08/10 $
-+ * $Change: 2047372 $
-+ *
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+#ifndef DWC_HOST_ONLY
-+
-+/** @file
-+ * This file implements PCD Core. All code in this file is portable and doesn't
-+ * use any OS specific functions.
-+ * PCD Core provides Interface, defined in <code><dwc_otg_pcd_if.h></code>
-+ * header file, which can be used to implement OS specific PCD interface.
-+ *
-+ * An important function of the PCD is managing interrupts generated
-+ * by the DWC_otg controller. The implementation of the DWC_otg device
-+ * mode interrupt service routines is in dwc_otg_pcd_intr.c.
-+ *
-+ * @todo Add Device Mode test modes (Test J mode, Test K mode, etc).
-+ * @todo Does it work when the request size is greater than DEPTSIZ
-+ * transfer size
-+ *
-+ */
-+
-+#include "dwc_otg_pcd.h"
-+
-+#ifdef DWC_UTE_CFI
-+#include "dwc_otg_cfi.h"
-+
-+extern int init_cfi(cfiobject_t * cfiobj);
-+#endif
-+
-+/**
-+ * Choose endpoint from ep arrays using usb_ep structure.
-+ */
-+static dwc_otg_pcd_ep_t *get_ep_from_handle(dwc_otg_pcd_t * pcd, void *handle)
-+{
-+ int i;
-+ if (pcd->ep0.priv == handle) {
-+ return &pcd->ep0;
-+ }
-+ for (i = 0; i < MAX_EPS_CHANNELS - 1; i++) {
-+ if (pcd->in_ep[i].priv == handle)
-+ return &pcd->in_ep[i];
-+ if (pcd->out_ep[i].priv == handle)
-+ return &pcd->out_ep[i];
-+ }
-+
-+ return NULL;
-+}
-+
-+/**
-+ * This function completes a request. It call's the request call back.
-+ */
-+void dwc_otg_request_done(dwc_otg_pcd_ep_t * ep, dwc_otg_pcd_request_t * req,
-+ int32_t status)
-+{
-+ unsigned stopped = ep->stopped;
-+
-+ DWC_DEBUGPL(DBG_PCDV, "%s(ep %p req %p)\n", __func__, ep, req);
-+ DWC_CIRCLEQ_REMOVE_INIT(&ep->queue, req, queue_entry);
-+
-+ /* don't modify queue heads during completion callback */
-+ ep->stopped = 1;
-+ /* spin_unlock/spin_lock now done in fops->complete() */
-+ ep->pcd->fops->complete(ep->pcd, ep->priv, req->priv, status,
-+ req->actual);
-+
-+ if (ep->pcd->request_pending > 0) {
-+ --ep->pcd->request_pending;
-+ }
-+
-+ ep->stopped = stopped;
-+ DWC_FREE(req);
-+}
-+
-+/**
-+ * This function terminates all the requsts in the EP request queue.
-+ */
-+void dwc_otg_request_nuke(dwc_otg_pcd_ep_t * ep)
-+{
-+ dwc_otg_pcd_request_t *req;
-+
-+ ep->stopped = 1;
-+
-+ /* called with irqs blocked?? */
-+ while (!DWC_CIRCLEQ_EMPTY(&ep->queue)) {
-+ req = DWC_CIRCLEQ_FIRST(&ep->queue);
-+ dwc_otg_request_done(ep, req, -DWC_E_SHUTDOWN);
-+ }
-+}
-+
-+void dwc_otg_pcd_start(dwc_otg_pcd_t * pcd,
-+ const struct dwc_otg_pcd_function_ops *fops)
-+{
-+ pcd->fops = fops;
-+}
-+
-+/**
-+ * PCD Callback function for initializing the PCD when switching to
-+ * device mode.
-+ *
-+ * @param p void pointer to the <code>dwc_otg_pcd_t</code>
-+ */
-+static int32_t dwc_otg_pcd_start_cb(void *p)
-+{
-+ dwc_otg_pcd_t *pcd = (dwc_otg_pcd_t *) p;
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+
-+ /*
-+ * Initialized the Core for Device mode.
-+ */
-+ if (dwc_otg_is_device_mode(core_if)) {
-+ dwc_otg_core_dev_init(core_if);
-+ /* Set core_if's lock pointer to the pcd->lock */
-+ core_if->lock = pcd->lock;
-+ }
-+ return 1;
-+}
-+
-+/** CFI-specific buffer allocation function for EP */
-+#ifdef DWC_UTE_CFI
-+uint8_t *cfiw_ep_alloc_buffer(dwc_otg_pcd_t * pcd, void *pep, dwc_dma_t * addr,
-+ size_t buflen, int flags)
-+{
-+ dwc_otg_pcd_ep_t *ep;
-+ ep = get_ep_from_handle(pcd, pep);
-+ if (!ep) {
-+ DWC_WARN("bad ep\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ return pcd->cfi->ops.ep_alloc_buf(pcd->cfi, pcd, ep, addr, buflen,
-+ flags);
-+}
-+#else
-+uint8_t *cfiw_ep_alloc_buffer(dwc_otg_pcd_t * pcd, void *pep, dwc_dma_t * addr,
-+ size_t buflen, int flags);
-+#endif
-+
-+/**
-+ * PCD Callback function for notifying the PCD when resuming from
-+ * suspend.
-+ *
-+ * @param p void pointer to the <code>dwc_otg_pcd_t</code>
-+ */
-+static int32_t dwc_otg_pcd_resume_cb(void *p)
-+{
-+ dwc_otg_pcd_t *pcd = (dwc_otg_pcd_t *) p;
-+
-+ if (pcd->fops->resume) {
-+ pcd->fops->resume(pcd);
-+ }
-+
-+ /* Stop the SRP timeout timer. */
-+ if ((GET_CORE_IF(pcd)->core_params->phy_type != DWC_PHY_TYPE_PARAM_FS)
-+ || (!GET_CORE_IF(pcd)->core_params->i2c_enable)) {
-+ if (GET_CORE_IF(pcd)->srp_timer_started) {
-+ GET_CORE_IF(pcd)->srp_timer_started = 0;
-+ DWC_TIMER_CANCEL(GET_CORE_IF(pcd)->srp_timer);
-+ }
-+ }
-+ return 1;
-+}
-+
-+/**
-+ * PCD Callback function for notifying the PCD device is suspended.
-+ *
-+ * @param p void pointer to the <code>dwc_otg_pcd_t</code>
-+ */
-+static int32_t dwc_otg_pcd_suspend_cb(void *p)
-+{
-+ dwc_otg_pcd_t *pcd = (dwc_otg_pcd_t *) p;
-+
-+ if (pcd->fops->suspend) {
-+ DWC_SPINUNLOCK(pcd->lock);
-+ pcd->fops->suspend(pcd);
-+ DWC_SPINLOCK(pcd->lock);
-+ }
-+
-+ return 1;
-+}
-+
-+/**
-+ * PCD Callback function for stopping the PCD when switching to Host
-+ * mode.
-+ *
-+ * @param p void pointer to the <code>dwc_otg_pcd_t</code>
-+ */
-+static int32_t dwc_otg_pcd_stop_cb(void *p)
-+{
-+ dwc_otg_pcd_t *pcd = (dwc_otg_pcd_t *) p;
-+ extern void dwc_otg_pcd_stop(dwc_otg_pcd_t * _pcd);
-+
-+ dwc_otg_pcd_stop(pcd);
-+ return 1;
-+}
-+
-+/**
-+ * PCD Callback structure for handling mode switching.
-+ */
-+static dwc_otg_cil_callbacks_t pcd_callbacks = {
-+ .start = dwc_otg_pcd_start_cb,
-+ .stop = dwc_otg_pcd_stop_cb,
-+ .suspend = dwc_otg_pcd_suspend_cb,
-+ .resume_wakeup = dwc_otg_pcd_resume_cb,
-+ .p = 0, /* Set at registration */
-+};
-+
-+/**
-+ * This function allocates a DMA Descriptor chain for the Endpoint
-+ * buffer to be used for a transfer to/from the specified endpoint.
-+ */
-+dwc_otg_dev_dma_desc_t *dwc_otg_ep_alloc_desc_chain(dwc_dma_t * dma_desc_addr,
-+ uint32_t count)
-+{
-+ return DWC_DMA_ALLOC_ATOMIC(count * sizeof(dwc_otg_dev_dma_desc_t),
-+ dma_desc_addr);
-+}
-+
-+/**
-+ * This function frees a DMA Descriptor chain that was allocated by ep_alloc_desc.
-+ */
-+void dwc_otg_ep_free_desc_chain(dwc_otg_dev_dma_desc_t * desc_addr,
-+ uint32_t dma_desc_addr, uint32_t count)
-+{
-+ DWC_DMA_FREE(count * sizeof(dwc_otg_dev_dma_desc_t), desc_addr,
-+ dma_desc_addr);
-+}
-+
-+#ifdef DWC_EN_ISOC
-+
-+/**
-+ * This function initializes a descriptor chain for Isochronous transfer
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param dwc_ep The EP to start the transfer on.
-+ *
-+ */
-+void dwc_otg_iso_ep_start_ddma_transfer(dwc_otg_core_if_t * core_if,
-+ dwc_ep_t * dwc_ep)
-+{
-+
-+ dsts_data_t dsts = {.d32 = 0 };
-+ depctl_data_t depctl = {.d32 = 0 };
-+ volatile uint32_t *addr;
-+ int i, j;
-+ uint32_t len;
-+
-+ if (dwc_ep->is_in)
-+ dwc_ep->desc_cnt = dwc_ep->buf_proc_intrvl / dwc_ep->bInterval;
-+ else
-+ dwc_ep->desc_cnt =
-+ dwc_ep->buf_proc_intrvl * dwc_ep->pkt_per_frm /
-+ dwc_ep->bInterval;
-+
-+ /** Allocate descriptors for double buffering */
-+ dwc_ep->iso_desc_addr =
-+ dwc_otg_ep_alloc_desc_chain(&dwc_ep->iso_dma_desc_addr,
-+ dwc_ep->desc_cnt * 2);
-+ if (dwc_ep->desc_addr) {
-+ DWC_WARN("%s, can't allocate DMA descriptor chain\n", __func__);
-+ return;
-+ }
-+
-+ dsts.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dsts);
-+
-+ /** ISO OUT EP */
-+ if (dwc_ep->is_in == 0) {
-+ dev_dma_desc_sts_t sts = {.d32 = 0 };
-+ dwc_otg_dev_dma_desc_t *dma_desc = dwc_ep->iso_desc_addr;
-+ dma_addr_t dma_ad;
-+ uint32_t data_per_desc;
-+ dwc_otg_dev_out_ep_regs_t *out_regs =
-+ core_if->dev_if->out_ep_regs[dwc_ep->num];
-+ int offset;
-+
-+ addr = &core_if->dev_if->out_ep_regs[dwc_ep->num]->doepctl;
-+ dma_ad = (dma_addr_t) DWC_READ_REG32(&(out_regs->doepdma));
-+
-+ /** Buffer 0 descriptors setup */
-+ dma_ad = dwc_ep->dma_addr0;
-+
-+ sts.b_iso_out.bs = BS_HOST_READY;
-+ sts.b_iso_out.rxsts = 0;
-+ sts.b_iso_out.l = 0;
-+ sts.b_iso_out.sp = 0;
-+ sts.b_iso_out.ioc = 0;
-+ sts.b_iso_out.pid = 0;
-+ sts.b_iso_out.framenum = 0;
-+
-+ offset = 0;
-+ for (i = 0; i < dwc_ep->desc_cnt - dwc_ep->pkt_per_frm;
-+ i += dwc_ep->pkt_per_frm) {
-+
-+ for (j = 0; j < dwc_ep->pkt_per_frm; ++j) {
-+ uint32_t len = (j + 1) * dwc_ep->maxpacket;
-+ if (len > dwc_ep->data_per_frame)
-+ data_per_desc =
-+ dwc_ep->data_per_frame -
-+ j * dwc_ep->maxpacket;
-+ else
-+ data_per_desc = dwc_ep->maxpacket;
-+ len = data_per_desc % 4;
-+ if (len)
-+ data_per_desc += 4 - len;
-+
-+ sts.b_iso_out.rxbytes = data_per_desc;
-+ dma_desc->buf = dma_ad;
-+ dma_desc->status.d32 = sts.d32;
-+
-+ offset += data_per_desc;
-+ dma_desc++;
-+ dma_ad += data_per_desc;
-+ }
-+ }
-+
-+ for (j = 0; j < dwc_ep->pkt_per_frm - 1; ++j) {
-+ uint32_t len = (j + 1) * dwc_ep->maxpacket;
-+ if (len > dwc_ep->data_per_frame)
-+ data_per_desc =
-+ dwc_ep->data_per_frame -
-+ j * dwc_ep->maxpacket;
-+ else
-+ data_per_desc = dwc_ep->maxpacket;
-+ len = data_per_desc % 4;
-+ if (len)
-+ data_per_desc += 4 - len;
-+ sts.b_iso_out.rxbytes = data_per_desc;
-+ dma_desc->buf = dma_ad;
-+ dma_desc->status.d32 = sts.d32;
-+
-+ offset += data_per_desc;
-+ dma_desc++;
-+ dma_ad += data_per_desc;
-+ }
-+
-+ sts.b_iso_out.ioc = 1;
-+ len = (j + 1) * dwc_ep->maxpacket;
-+ if (len > dwc_ep->data_per_frame)
-+ data_per_desc =
-+ dwc_ep->data_per_frame - j * dwc_ep->maxpacket;
-+ else
-+ data_per_desc = dwc_ep->maxpacket;
-+ len = data_per_desc % 4;
-+ if (len)
-+ data_per_desc += 4 - len;
-+ sts.b_iso_out.rxbytes = data_per_desc;
-+
-+ dma_desc->buf = dma_ad;
-+ dma_desc->status.d32 = sts.d32;
-+ dma_desc++;
-+
-+ /** Buffer 1 descriptors setup */
-+ sts.b_iso_out.ioc = 0;
-+ dma_ad = dwc_ep->dma_addr1;
-+
-+ offset = 0;
-+ for (i = 0; i < dwc_ep->desc_cnt - dwc_ep->pkt_per_frm;
-+ i += dwc_ep->pkt_per_frm) {
-+ for (j = 0; j < dwc_ep->pkt_per_frm; ++j) {
-+ uint32_t len = (j + 1) * dwc_ep->maxpacket;
-+ if (len > dwc_ep->data_per_frame)
-+ data_per_desc =
-+ dwc_ep->data_per_frame -
-+ j * dwc_ep->maxpacket;
-+ else
-+ data_per_desc = dwc_ep->maxpacket;
-+ len = data_per_desc % 4;
-+ if (len)
-+ data_per_desc += 4 - len;
-+
-+ data_per_desc =
-+ sts.b_iso_out.rxbytes = data_per_desc;
-+ dma_desc->buf = dma_ad;
-+ dma_desc->status.d32 = sts.d32;
-+
-+ offset += data_per_desc;
-+ dma_desc++;
-+ dma_ad += data_per_desc;
-+ }
-+ }
-+ for (j = 0; j < dwc_ep->pkt_per_frm - 1; ++j) {
-+ data_per_desc =
-+ ((j + 1) * dwc_ep->maxpacket >
-+ dwc_ep->data_per_frame) ? dwc_ep->data_per_frame -
-+ j * dwc_ep->maxpacket : dwc_ep->maxpacket;
-+ data_per_desc +=
-+ (data_per_desc % 4) ? (4 - data_per_desc % 4) : 0;
-+ sts.b_iso_out.rxbytes = data_per_desc;
-+ dma_desc->buf = dma_ad;
-+ dma_desc->status.d32 = sts.d32;
-+
-+ offset += data_per_desc;
-+ dma_desc++;
-+ dma_ad += data_per_desc;
-+ }
-+
-+ sts.b_iso_out.ioc = 1;
-+ sts.b_iso_out.l = 1;
-+ data_per_desc =
-+ ((j + 1) * dwc_ep->maxpacket >
-+ dwc_ep->data_per_frame) ? dwc_ep->data_per_frame -
-+ j * dwc_ep->maxpacket : dwc_ep->maxpacket;
-+ data_per_desc +=
-+ (data_per_desc % 4) ? (4 - data_per_desc % 4) : 0;
-+ sts.b_iso_out.rxbytes = data_per_desc;
-+
-+ dma_desc->buf = dma_ad;
-+ dma_desc->status.d32 = sts.d32;
-+
-+ dwc_ep->next_frame = 0;
-+
-+ /** Write dma_ad into DOEPDMA register */
-+ DWC_WRITE_REG32(&(out_regs->doepdma),
-+ (uint32_t) dwc_ep->iso_dma_desc_addr);
-+
-+ }
-+ /** ISO IN EP */
-+ else {
-+ dev_dma_desc_sts_t sts = {.d32 = 0 };
-+ dwc_otg_dev_dma_desc_t *dma_desc = dwc_ep->iso_desc_addr;
-+ dma_addr_t dma_ad;
-+ dwc_otg_dev_in_ep_regs_t *in_regs =
-+ core_if->dev_if->in_ep_regs[dwc_ep->num];
-+ unsigned int frmnumber;
-+ fifosize_data_t txfifosize, rxfifosize;
-+
-+ txfifosize.d32 =
-+ DWC_READ_REG32(&core_if->dev_if->in_ep_regs[dwc_ep->num]->
-+ dtxfsts);
-+ rxfifosize.d32 =
-+ DWC_READ_REG32(&core_if->core_global_regs->grxfsiz);
-+
-+ addr = &core_if->dev_if->in_ep_regs[dwc_ep->num]->diepctl;
-+
-+ dma_ad = dwc_ep->dma_addr0;
-+
-+ dsts.d32 =
-+ DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dsts);
-+
-+ sts.b_iso_in.bs = BS_HOST_READY;
-+ sts.b_iso_in.txsts = 0;
-+ sts.b_iso_in.sp =
-+ (dwc_ep->data_per_frame % dwc_ep->maxpacket) ? 1 : 0;
-+ sts.b_iso_in.ioc = 0;
-+ sts.b_iso_in.pid = dwc_ep->pkt_per_frm;
-+
-+ frmnumber = dwc_ep->next_frame;
-+
-+ sts.b_iso_in.framenum = frmnumber;
-+ sts.b_iso_in.txbytes = dwc_ep->data_per_frame;
-+ sts.b_iso_in.l = 0;
-+
-+ /** Buffer 0 descriptors setup */
-+ for (i = 0; i < dwc_ep->desc_cnt - 1; i++) {
-+ dma_desc->buf = dma_ad;
-+ dma_desc->status.d32 = sts.d32;
-+ dma_desc++;
-+
-+ dma_ad += dwc_ep->data_per_frame;
-+ sts.b_iso_in.framenum += dwc_ep->bInterval;
-+ }
-+
-+ sts.b_iso_in.ioc = 1;
-+ dma_desc->buf = dma_ad;
-+ dma_desc->status.d32 = sts.d32;
-+ ++dma_desc;
-+
-+ /** Buffer 1 descriptors setup */
-+ sts.b_iso_in.ioc = 0;
-+ dma_ad = dwc_ep->dma_addr1;
-+
-+ for (i = 0; i < dwc_ep->desc_cnt - dwc_ep->pkt_per_frm;
-+ i += dwc_ep->pkt_per_frm) {
-+ dma_desc->buf = dma_ad;
-+ dma_desc->status.d32 = sts.d32;
-+ dma_desc++;
-+
-+ dma_ad += dwc_ep->data_per_frame;
-+ sts.b_iso_in.framenum += dwc_ep->bInterval;
-+
-+ sts.b_iso_in.ioc = 0;
-+ }
-+ sts.b_iso_in.ioc = 1;
-+ sts.b_iso_in.l = 1;
-+
-+ dma_desc->buf = dma_ad;
-+ dma_desc->status.d32 = sts.d32;
-+
-+ dwc_ep->next_frame = sts.b_iso_in.framenum + dwc_ep->bInterval;
-+
-+ /** Write dma_ad into diepdma register */
-+ DWC_WRITE_REG32(&(in_regs->diepdma),
-+ (uint32_t) dwc_ep->iso_dma_desc_addr);
-+ }
-+ /** Enable endpoint, clear nak */
-+ depctl.d32 = 0;
-+ depctl.b.epena = 1;
-+ depctl.b.usbactep = 1;
-+ depctl.b.cnak = 1;
-+
-+ DWC_MODIFY_REG32(addr, depctl.d32, depctl.d32);
-+ depctl.d32 = DWC_READ_REG32(addr);
-+}
-+
-+/**
-+ * This function initializes a descriptor chain for Isochronous transfer
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param ep The EP to start the transfer on.
-+ *
-+ */
-+void dwc_otg_iso_ep_start_buf_transfer(dwc_otg_core_if_t * core_if,
-+ dwc_ep_t * ep)
-+{
-+ depctl_data_t depctl = {.d32 = 0 };
-+ volatile uint32_t *addr;
-+
-+ if (ep->is_in) {
-+ addr = &core_if->dev_if->in_ep_regs[ep->num]->diepctl;
-+ } else {
-+ addr = &core_if->dev_if->out_ep_regs[ep->num]->doepctl;
-+ }
-+
-+ if (core_if->dma_enable == 0 || core_if->dma_desc_enable != 0) {
-+ return;
-+ } else {
-+ deptsiz_data_t deptsiz = {.d32 = 0 };
-+
-+ ep->xfer_len =
-+ ep->data_per_frame * ep->buf_proc_intrvl / ep->bInterval;
-+ ep->pkt_cnt =
-+ (ep->xfer_len - 1 + ep->maxpacket) / ep->maxpacket;
-+ ep->xfer_count = 0;
-+ ep->xfer_buff =
-+ (ep->proc_buf_num) ? ep->xfer_buff1 : ep->xfer_buff0;
-+ ep->dma_addr =
-+ (ep->proc_buf_num) ? ep->dma_addr1 : ep->dma_addr0;
-+
-+ if (ep->is_in) {
-+ /* Program the transfer size and packet count
-+ * as follows: xfersize = N * maxpacket +
-+ * short_packet pktcnt = N + (short_packet
-+ * exist ? 1 : 0)
-+ */
-+ deptsiz.b.mc = ep->pkt_per_frm;
-+ deptsiz.b.xfersize = ep->xfer_len;
-+ deptsiz.b.pktcnt =
-+ (ep->xfer_len - 1 + ep->maxpacket) / ep->maxpacket;
-+ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[ep->num]->
-+ dieptsiz, deptsiz.d32);
-+
-+ /* Write the DMA register */
-+ DWC_WRITE_REG32(&
-+ (core_if->dev_if->in_ep_regs[ep->num]->
-+ diepdma), (uint32_t) ep->dma_addr);
-+
-+ } else {
-+ deptsiz.b.pktcnt =
-+ (ep->xfer_len + (ep->maxpacket - 1)) /
-+ ep->maxpacket;
-+ deptsiz.b.xfersize = deptsiz.b.pktcnt * ep->maxpacket;
-+
-+ DWC_WRITE_REG32(&core_if->dev_if->out_ep_regs[ep->num]->
-+ doeptsiz, deptsiz.d32);
-+
-+ /* Write the DMA register */
-+ DWC_WRITE_REG32(&
-+ (core_if->dev_if->out_ep_regs[ep->num]->
-+ doepdma), (uint32_t) ep->dma_addr);
-+
-+ }
-+ /** Enable endpoint, clear nak */
-+ depctl.d32 = 0;
-+ depctl.b.epena = 1;
-+ depctl.b.cnak = 1;
-+
-+ DWC_MODIFY_REG32(addr, depctl.d32, depctl.d32);
-+ }
-+}
-+
-+/**
-+ * This function does the setup for a data transfer for an EP and
-+ * starts the transfer. For an IN transfer, the packets will be
-+ * loaded into the appropriate Tx FIFO in the ISR. For OUT transfers,
-+ * the packets are unloaded from the Rx FIFO in the ISR.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param ep The EP to start the transfer on.
-+ */
-+
-+static void dwc_otg_iso_ep_start_transfer(dwc_otg_core_if_t * core_if,
-+ dwc_ep_t * ep)
-+{
-+ if (core_if->dma_enable) {
-+ if (core_if->dma_desc_enable) {
-+ if (ep->is_in) {
-+ ep->desc_cnt = ep->pkt_cnt / ep->pkt_per_frm;
-+ } else {
-+ ep->desc_cnt = ep->pkt_cnt;
-+ }
-+ dwc_otg_iso_ep_start_ddma_transfer(core_if, ep);
-+ } else {
-+ if (core_if->pti_enh_enable) {
-+ dwc_otg_iso_ep_start_buf_transfer(core_if, ep);
-+ } else {
-+ ep->cur_pkt_addr =
-+ (ep->proc_buf_num) ? ep->xfer_buff1 : ep->
-+ xfer_buff0;
-+ ep->cur_pkt_dma_addr =
-+ (ep->proc_buf_num) ? ep->dma_addr1 : ep->
-+ dma_addr0;
-+ dwc_otg_iso_ep_start_frm_transfer(core_if, ep);
-+ }
-+ }
-+ } else {
-+ ep->cur_pkt_addr =
-+ (ep->proc_buf_num) ? ep->xfer_buff1 : ep->xfer_buff0;
-+ ep->cur_pkt_dma_addr =
-+ (ep->proc_buf_num) ? ep->dma_addr1 : ep->dma_addr0;
-+ dwc_otg_iso_ep_start_frm_transfer(core_if, ep);
-+ }
-+}
-+
-+/**
-+ * This function stops transfer for an EP and
-+ * resets the ep's variables.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param ep The EP to start the transfer on.
-+ */
-+
-+void dwc_otg_iso_ep_stop_transfer(dwc_otg_core_if_t * core_if, dwc_ep_t * ep)
-+{
-+ depctl_data_t depctl = {.d32 = 0 };
-+ volatile uint32_t *addr;
-+
-+ if (ep->is_in == 1) {
-+ addr = &core_if->dev_if->in_ep_regs[ep->num]->diepctl;
-+ } else {
-+ addr = &core_if->dev_if->out_ep_regs[ep->num]->doepctl;
-+ }
-+
-+ /* disable the ep */
-+ depctl.d32 = DWC_READ_REG32(addr);
-+
-+ depctl.b.epdis = 1;
-+ depctl.b.snak = 1;
-+
-+ DWC_WRITE_REG32(addr, depctl.d32);
-+
-+ if (core_if->dma_desc_enable &&
-+ ep->iso_desc_addr && ep->iso_dma_desc_addr) {
-+ dwc_otg_ep_free_desc_chain(ep->iso_desc_addr,
-+ ep->iso_dma_desc_addr,
-+ ep->desc_cnt * 2);
-+ }
-+
-+ /* reset varibales */
-+ ep->dma_addr0 = 0;
-+ ep->dma_addr1 = 0;
-+ ep->xfer_buff0 = 0;
-+ ep->xfer_buff1 = 0;
-+ ep->data_per_frame = 0;
-+ ep->data_pattern_frame = 0;
-+ ep->sync_frame = 0;
-+ ep->buf_proc_intrvl = 0;
-+ ep->bInterval = 0;
-+ ep->proc_buf_num = 0;
-+ ep->pkt_per_frm = 0;
-+ ep->pkt_per_frm = 0;
-+ ep->desc_cnt = 0;
-+ ep->iso_desc_addr = 0;
-+ ep->iso_dma_desc_addr = 0;
-+}
-+
-+int dwc_otg_pcd_iso_ep_start(dwc_otg_pcd_t * pcd, void *ep_handle,
-+ uint8_t * buf0, uint8_t * buf1, dwc_dma_t dma0,
-+ dwc_dma_t dma1, int sync_frame, int dp_frame,
-+ int data_per_frame, int start_frame,
-+ int buf_proc_intrvl, void *req_handle,
-+ int atomic_alloc)
-+{
-+ dwc_otg_pcd_ep_t *ep;
-+ dwc_irqflags_t flags = 0;
-+ dwc_ep_t *dwc_ep;
-+ int32_t frm_data;
-+ dsts_data_t dsts;
-+ dwc_otg_core_if_t *core_if;
-+
-+ ep = get_ep_from_handle(pcd, ep_handle);
-+
-+ if (!ep || !ep->desc || ep->dwc_ep.num == 0) {
-+ DWC_WARN("bad ep\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ DWC_SPINLOCK_IRQSAVE(pcd->lock, &flags);
-+ core_if = GET_CORE_IF(pcd);
-+ dwc_ep = &ep->dwc_ep;
-+
-+ if (ep->iso_req_handle) {
-+ DWC_WARN("ISO request in progress\n");
-+ }
-+
-+ dwc_ep->dma_addr0 = dma0;
-+ dwc_ep->dma_addr1 = dma1;
-+
-+ dwc_ep->xfer_buff0 = buf0;
-+ dwc_ep->xfer_buff1 = buf1;
-+
-+ dwc_ep->data_per_frame = data_per_frame;
-+
-+ /** @todo - pattern data support is to be implemented in the future */
-+ dwc_ep->data_pattern_frame = dp_frame;
-+ dwc_ep->sync_frame = sync_frame;
-+
-+ dwc_ep->buf_proc_intrvl = buf_proc_intrvl;
-+
-+ dwc_ep->bInterval = 1 << (ep->desc->bInterval - 1);
-+
-+ dwc_ep->proc_buf_num = 0;
-+
-+ dwc_ep->pkt_per_frm = 0;
-+ frm_data = ep->dwc_ep.data_per_frame;
-+ while (frm_data > 0) {
-+ dwc_ep->pkt_per_frm++;
-+ frm_data -= ep->dwc_ep.maxpacket;
-+ }
-+
-+ dsts.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dsts);
-+
-+ if (start_frame == -1) {
-+ dwc_ep->next_frame = dsts.b.soffn + 1;
-+ if (dwc_ep->bInterval != 1) {
-+ dwc_ep->next_frame =
-+ dwc_ep->next_frame + (dwc_ep->bInterval - 1 -
-+ dwc_ep->next_frame %
-+ dwc_ep->bInterval);
-+ }
-+ } else {
-+ dwc_ep->next_frame = start_frame;
-+ }
-+
-+ if (!core_if->pti_enh_enable) {
-+ dwc_ep->pkt_cnt =
-+ dwc_ep->buf_proc_intrvl * dwc_ep->pkt_per_frm /
-+ dwc_ep->bInterval;
-+ } else {
-+ dwc_ep->pkt_cnt =
-+ (dwc_ep->data_per_frame *
-+ (dwc_ep->buf_proc_intrvl / dwc_ep->bInterval)
-+ - 1 + dwc_ep->maxpacket) / dwc_ep->maxpacket;
-+ }
-+
-+ if (core_if->dma_desc_enable) {
-+ dwc_ep->desc_cnt =
-+ dwc_ep->buf_proc_intrvl * dwc_ep->pkt_per_frm /
-+ dwc_ep->bInterval;
-+ }
-+
-+ if (atomic_alloc) {
-+ dwc_ep->pkt_info =
-+ DWC_ALLOC_ATOMIC(sizeof(iso_pkt_info_t) * dwc_ep->pkt_cnt);
-+ } else {
-+ dwc_ep->pkt_info =
-+ DWC_ALLOC(sizeof(iso_pkt_info_t) * dwc_ep->pkt_cnt);
-+ }
-+ if (!dwc_ep->pkt_info) {
-+ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags);
-+ return -DWC_E_NO_MEMORY;
-+ }
-+ if (core_if->pti_enh_enable) {
-+ dwc_memset(dwc_ep->pkt_info, 0,
-+ sizeof(iso_pkt_info_t) * dwc_ep->pkt_cnt);
-+ }
-+
-+ dwc_ep->cur_pkt = 0;
-+ ep->iso_req_handle = req_handle;
-+
-+ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags);
-+ dwc_otg_iso_ep_start_transfer(core_if, dwc_ep);
-+ return 0;
-+}
-+
-+int dwc_otg_pcd_iso_ep_stop(dwc_otg_pcd_t * pcd, void *ep_handle,
-+ void *req_handle)
-+{
-+ dwc_irqflags_t flags = 0;
-+ dwc_otg_pcd_ep_t *ep;
-+ dwc_ep_t *dwc_ep;
-+
-+ ep = get_ep_from_handle(pcd, ep_handle);
-+ if (!ep || !ep->desc || ep->dwc_ep.num == 0) {
-+ DWC_WARN("bad ep\n");
-+ return -DWC_E_INVALID;
-+ }
-+ dwc_ep = &ep->dwc_ep;
-+
-+ dwc_otg_iso_ep_stop_transfer(GET_CORE_IF(pcd), dwc_ep);
-+
-+ DWC_FREE(dwc_ep->pkt_info);
-+ DWC_SPINLOCK_IRQSAVE(pcd->lock, &flags);
-+ if (ep->iso_req_handle != req_handle) {
-+ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags);
-+ return -DWC_E_INVALID;
-+ }
-+
-+ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags);
-+
-+ ep->iso_req_handle = 0;
-+ return 0;
-+}
-+
-+/**
-+ * This function is used for perodical data exchnage between PCD and gadget drivers.
-+ * for Isochronous EPs
-+ *
-+ * - Every time a sync period completes this function is called to
-+ * perform data exchange between PCD and gadget
-+ */
-+void dwc_otg_iso_buffer_done(dwc_otg_pcd_t * pcd, dwc_otg_pcd_ep_t * ep,
-+ void *req_handle)
-+{
-+ int i;
-+ dwc_ep_t *dwc_ep;
-+
-+ dwc_ep = &ep->dwc_ep;
-+
-+ DWC_SPINUNLOCK(ep->pcd->lock);
-+ pcd->fops->isoc_complete(pcd, ep->priv, ep->iso_req_handle,
-+ dwc_ep->proc_buf_num ^ 0x1);
-+ DWC_SPINLOCK(ep->pcd->lock);
-+
-+ for (i = 0; i < dwc_ep->pkt_cnt; ++i) {
-+ dwc_ep->pkt_info[i].status = 0;
-+ dwc_ep->pkt_info[i].offset = 0;
-+ dwc_ep->pkt_info[i].length = 0;
-+ }
-+}
-+
-+int dwc_otg_pcd_get_iso_packet_count(dwc_otg_pcd_t * pcd, void *ep_handle,
-+ void *iso_req_handle)
-+{
-+ dwc_otg_pcd_ep_t *ep;
-+ dwc_ep_t *dwc_ep;
-+
-+ ep = get_ep_from_handle(pcd, ep_handle);
-+ if (!ep->desc || ep->dwc_ep.num == 0) {
-+ DWC_WARN("bad ep\n");
-+ return -DWC_E_INVALID;
-+ }
-+ dwc_ep = &ep->dwc_ep;
-+
-+ return dwc_ep->pkt_cnt;
-+}
-+
-+void dwc_otg_pcd_get_iso_packet_params(dwc_otg_pcd_t * pcd, void *ep_handle,
-+ void *iso_req_handle, int packet,
-+ int *status, int *actual, int *offset)
-+{
-+ dwc_otg_pcd_ep_t *ep;
-+ dwc_ep_t *dwc_ep;
-+
-+ ep = get_ep_from_handle(pcd, ep_handle);
-+ if (!ep)
-+ DWC_WARN("bad ep\n");
-+
-+ dwc_ep = &ep->dwc_ep;
-+
-+ *status = dwc_ep->pkt_info[packet].status;
-+ *actual = dwc_ep->pkt_info[packet].length;
-+ *offset = dwc_ep->pkt_info[packet].offset;
-+}
-+
-+#endif /* DWC_EN_ISOC */
-+
-+static void dwc_otg_pcd_init_ep(dwc_otg_pcd_t * pcd, dwc_otg_pcd_ep_t * pcd_ep,
-+ uint32_t is_in, uint32_t ep_num)
-+{
-+ /* Init EP structure */
-+ pcd_ep->desc = 0;
-+ pcd_ep->pcd = pcd;
-+ pcd_ep->stopped = 1;
-+ pcd_ep->queue_sof = 0;
-+
-+ /* Init DWC ep structure */
-+ pcd_ep->dwc_ep.is_in = is_in;
-+ pcd_ep->dwc_ep.num = ep_num;
-+ pcd_ep->dwc_ep.active = 0;
-+ pcd_ep->dwc_ep.tx_fifo_num = 0;
-+ /* Control until ep is actvated */
-+ pcd_ep->dwc_ep.type = DWC_OTG_EP_TYPE_CONTROL;
-+ pcd_ep->dwc_ep.maxpacket = MAX_PACKET_SIZE;
-+ pcd_ep->dwc_ep.dma_addr = 0;
-+ pcd_ep->dwc_ep.start_xfer_buff = 0;
-+ pcd_ep->dwc_ep.xfer_buff = 0;
-+ pcd_ep->dwc_ep.xfer_len = 0;
-+ pcd_ep->dwc_ep.xfer_count = 0;
-+ pcd_ep->dwc_ep.sent_zlp = 0;
-+ pcd_ep->dwc_ep.total_len = 0;
-+ pcd_ep->dwc_ep.desc_addr = 0;
-+ pcd_ep->dwc_ep.dma_desc_addr = 0;
-+ DWC_CIRCLEQ_INIT(&pcd_ep->queue);
-+}
-+
-+/**
-+ * Initialize ep's
-+ */
-+static void dwc_otg_pcd_reinit(dwc_otg_pcd_t * pcd)
-+{
-+ int i;
-+ uint32_t hwcfg1;
-+ dwc_otg_pcd_ep_t *ep;
-+ int in_ep_cntr, out_ep_cntr;
-+ uint32_t num_in_eps = (GET_CORE_IF(pcd))->dev_if->num_in_eps;
-+ uint32_t num_out_eps = (GET_CORE_IF(pcd))->dev_if->num_out_eps;
-+
-+ /**
-+ * Initialize the EP0 structure.
-+ */
-+ ep = &pcd->ep0;
-+ dwc_otg_pcd_init_ep(pcd, ep, 0, 0);
-+
-+ in_ep_cntr = 0;
-+ hwcfg1 = (GET_CORE_IF(pcd))->hwcfg1.d32 >> 3;
-+ for (i = 1; in_ep_cntr < num_in_eps; i++) {
-+ if ((hwcfg1 & 0x1) == 0) {
-+ dwc_otg_pcd_ep_t *ep = &pcd->in_ep[in_ep_cntr];
-+ in_ep_cntr++;
-+ /**
-+ * @todo NGS: Add direction to EP, based on contents
-+ * of HWCFG1. Need a copy of HWCFG1 in pcd structure?
-+ * sprintf(";r
-+ */
-+ dwc_otg_pcd_init_ep(pcd, ep, 1 /* IN */ , i);
-+
-+ DWC_CIRCLEQ_INIT(&ep->queue);
-+ }
-+ hwcfg1 >>= 2;
-+ }
-+
-+ out_ep_cntr = 0;
-+ hwcfg1 = (GET_CORE_IF(pcd))->hwcfg1.d32 >> 2;
-+ for (i = 1; out_ep_cntr < num_out_eps; i++) {
-+ if ((hwcfg1 & 0x1) == 0) {
-+ dwc_otg_pcd_ep_t *ep = &pcd->out_ep[out_ep_cntr];
-+ out_ep_cntr++;
-+ /**
-+ * @todo NGS: Add direction to EP, based on contents
-+ * of HWCFG1. Need a copy of HWCFG1 in pcd structure?
-+ * sprintf(";r
-+ */
-+ dwc_otg_pcd_init_ep(pcd, ep, 0 /* OUT */ , i);
-+ DWC_CIRCLEQ_INIT(&ep->queue);
-+ }
-+ hwcfg1 >>= 2;
-+ }
-+
-+ pcd->ep0state = EP0_DISCONNECT;
-+ pcd->ep0.dwc_ep.maxpacket = MAX_EP0_SIZE;
-+ pcd->ep0.dwc_ep.type = DWC_OTG_EP_TYPE_CONTROL;
-+}
-+
-+/**
-+ * This function is called when the SRP timer expires. The SRP should
-+ * complete within 6 seconds.
-+ */
-+static void srp_timeout(void *ptr)
-+{
-+ gotgctl_data_t gotgctl;
-+ dwc_otg_core_if_t *core_if = (dwc_otg_core_if_t *) ptr;
-+ volatile uint32_t *addr = &core_if->core_global_regs->gotgctl;
-+
-+ gotgctl.d32 = DWC_READ_REG32(addr);
-+
-+ core_if->srp_timer_started = 0;
-+
-+ if (core_if->adp_enable) {
-+ if (gotgctl.b.bsesvld == 0) {
-+ gpwrdn_data_t gpwrdn = {.d32 = 0 };
-+ DWC_PRINTF("SRP Timeout BSESSVLD = 0\n");
-+ /* Power off the core */
-+ if (core_if->power_down == 2) {
-+ gpwrdn.b.pwrdnswtch = 1;
-+ DWC_MODIFY_REG32(&core_if->
-+ core_global_regs->gpwrdn,
-+ gpwrdn.d32, 0);
-+ }
-+
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuintsel = 1;
-+ gpwrdn.b.pmuactv = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0,
-+ gpwrdn.d32);
-+ dwc_otg_adp_probe_start(core_if);
-+ } else {
-+ DWC_PRINTF("SRP Timeout BSESSVLD = 1\n");
-+ core_if->op_state = B_PERIPHERAL;
-+ dwc_otg_core_init(core_if);
-+ dwc_otg_enable_global_interrupts(core_if);
-+ cil_pcd_start(core_if);
-+ }
-+ }
-+
-+ if ((core_if->core_params->phy_type == DWC_PHY_TYPE_PARAM_FS) &&
-+ (core_if->core_params->i2c_enable)) {
-+ DWC_PRINTF("SRP Timeout\n");
-+
-+ if ((core_if->srp_success) && (gotgctl.b.bsesvld)) {
-+ if (core_if->pcd_cb && core_if->pcd_cb->resume_wakeup) {
-+ core_if->pcd_cb->resume_wakeup(core_if->pcd_cb->p);
-+ }
-+
-+ /* Clear Session Request */
-+ gotgctl.d32 = 0;
-+ gotgctl.b.sesreq = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gotgctl,
-+ gotgctl.d32, 0);
-+
-+ core_if->srp_success = 0;
-+ } else {
-+ __DWC_ERROR("Device not connected/responding\n");
-+ gotgctl.b.sesreq = 0;
-+ DWC_WRITE_REG32(addr, gotgctl.d32);
-+ }
-+ } else if (gotgctl.b.sesreq) {
-+ DWC_PRINTF("SRP Timeout\n");
-+
-+ __DWC_ERROR("Device not connected/responding\n");
-+ gotgctl.b.sesreq = 0;
-+ DWC_WRITE_REG32(addr, gotgctl.d32);
-+ } else {
-+ DWC_PRINTF(" SRP GOTGCTL=%0x\n", gotgctl.d32);
-+ }
-+}
-+
-+/**
-+ * Tasklet
-+ *
-+ */
-+extern void start_next_request(dwc_otg_pcd_ep_t * ep);
-+
-+static void start_xfer_tasklet_func(void *data)
-+{
-+ dwc_otg_pcd_t *pcd = (dwc_otg_pcd_t *) data;
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+
-+ int i;
-+ depctl_data_t diepctl;
-+
-+ DWC_DEBUGPL(DBG_PCDV, "Start xfer tasklet\n");
-+
-+ diepctl.d32 = DWC_READ_REG32(&core_if->dev_if->in_ep_regs[0]->diepctl);
-+
-+ if (pcd->ep0.queue_sof) {
-+ pcd->ep0.queue_sof = 0;
-+ start_next_request(&pcd->ep0);
-+ // break;
-+ }
-+
-+ for (i = 0; i < core_if->dev_if->num_in_eps; i++) {
-+ depctl_data_t diepctl;
-+ diepctl.d32 =
-+ DWC_READ_REG32(&core_if->dev_if->in_ep_regs[i]->diepctl);
-+
-+ if (pcd->in_ep[i].queue_sof) {
-+ pcd->in_ep[i].queue_sof = 0;
-+ start_next_request(&pcd->in_ep[i]);
-+ // break;
-+ }
-+ }
-+
-+ return;
-+}
-+
-+/**
-+ * This function initialized the PCD portion of the driver.
-+ *
-+ */
-+dwc_otg_pcd_t *dwc_otg_pcd_init(dwc_otg_core_if_t * core_if)
-+{
-+ dwc_otg_pcd_t *pcd = NULL;
-+ dwc_otg_dev_if_t *dev_if;
-+ int i;
-+
-+ /*
-+ * Allocate PCD structure
-+ */
-+ pcd = DWC_ALLOC(sizeof(dwc_otg_pcd_t));
-+
-+ if (pcd == NULL) {
-+ return NULL;
-+ }
-+
-+#if (defined(DWC_LINUX) && defined(CONFIG_DEBUG_SPINLOCK))
-+ DWC_SPINLOCK_ALLOC_LINUX_DEBUG(pcd->lock);
-+#else
-+ pcd->lock = DWC_SPINLOCK_ALLOC();
-+#endif
-+ DWC_DEBUGPL(DBG_HCDV, "Init of PCD %p given core_if %p\n",
-+ pcd, core_if);//GRAYG
-+ if (!pcd->lock) {
-+ DWC_ERROR("Could not allocate lock for pcd");
-+ DWC_FREE(pcd);
-+ return NULL;
-+ }
-+ /* Set core_if's lock pointer to hcd->lock */
-+ core_if->lock = pcd->lock;
-+ pcd->core_if = core_if;
-+
-+ dev_if = core_if->dev_if;
-+ dev_if->isoc_ep = NULL;
-+
-+ if (core_if->hwcfg4.b.ded_fifo_en) {
-+ DWC_PRINTF("Dedicated Tx FIFOs mode\n");
-+ } else {
-+ DWC_PRINTF("Shared Tx FIFO mode\n");
-+ }
-+
-+ /*
-+ * Initialized the Core for Device mode here if there is nod ADP support.
-+ * Otherwise it will be done later in dwc_otg_adp_start routine.
-+ */
-+ if (dwc_otg_is_device_mode(core_if) /*&& !core_if->adp_enable*/) {
-+ dwc_otg_core_dev_init(core_if);
-+ }
-+
-+ /*
-+ * Register the PCD Callbacks.
-+ */
-+ dwc_otg_cil_register_pcd_callbacks(core_if, &pcd_callbacks, pcd);
-+
-+ /*
-+ * Initialize the DMA buffer for SETUP packets
-+ */
-+ if (GET_CORE_IF(pcd)->dma_enable) {
-+ pcd->setup_pkt =
-+ DWC_DMA_ALLOC(sizeof(*pcd->setup_pkt) * 5,
-+ &pcd->setup_pkt_dma_handle);
-+ if (pcd->setup_pkt == NULL) {
-+ DWC_FREE(pcd);
-+ return NULL;
-+ }
-+
-+ pcd->status_buf =
-+ DWC_DMA_ALLOC(sizeof(uint16_t),
-+ &pcd->status_buf_dma_handle);
-+ if (pcd->status_buf == NULL) {
-+ DWC_DMA_FREE(sizeof(*pcd->setup_pkt) * 5,
-+ pcd->setup_pkt, pcd->setup_pkt_dma_handle);
-+ DWC_FREE(pcd);
-+ return NULL;
-+ }
-+
-+ if (GET_CORE_IF(pcd)->dma_desc_enable) {
-+ dev_if->setup_desc_addr[0] =
-+ dwc_otg_ep_alloc_desc_chain
-+ (&dev_if->dma_setup_desc_addr[0], 1);
-+ dev_if->setup_desc_addr[1] =
-+ dwc_otg_ep_alloc_desc_chain
-+ (&dev_if->dma_setup_desc_addr[1], 1);
-+ dev_if->in_desc_addr =
-+ dwc_otg_ep_alloc_desc_chain
-+ (&dev_if->dma_in_desc_addr, 1);
-+ dev_if->out_desc_addr =
-+ dwc_otg_ep_alloc_desc_chain
-+ (&dev_if->dma_out_desc_addr, 1);
-+ pcd->data_terminated = 0;
-+
-+ if (dev_if->setup_desc_addr[0] == 0
-+ || dev_if->setup_desc_addr[1] == 0
-+ || dev_if->in_desc_addr == 0
-+ || dev_if->out_desc_addr == 0) {
-+
-+ if (dev_if->out_desc_addr)
-+ dwc_otg_ep_free_desc_chain
-+ (dev_if->out_desc_addr,
-+ dev_if->dma_out_desc_addr, 1);
-+ if (dev_if->in_desc_addr)
-+ dwc_otg_ep_free_desc_chain
-+ (dev_if->in_desc_addr,
-+ dev_if->dma_in_desc_addr, 1);
-+ if (dev_if->setup_desc_addr[1])
-+ dwc_otg_ep_free_desc_chain
-+ (dev_if->setup_desc_addr[1],
-+ dev_if->dma_setup_desc_addr[1], 1);
-+ if (dev_if->setup_desc_addr[0])
-+ dwc_otg_ep_free_desc_chain
-+ (dev_if->setup_desc_addr[0],
-+ dev_if->dma_setup_desc_addr[0], 1);
-+
-+ DWC_DMA_FREE(sizeof(*pcd->setup_pkt) * 5,
-+ pcd->setup_pkt,
-+ pcd->setup_pkt_dma_handle);
-+ DWC_DMA_FREE(sizeof(*pcd->status_buf),
-+ pcd->status_buf,
-+ pcd->status_buf_dma_handle);
-+
-+ DWC_FREE(pcd);
-+
-+ return NULL;
-+ }
-+ }
-+ } else {
-+ pcd->setup_pkt = DWC_ALLOC(sizeof(*pcd->setup_pkt) * 5);
-+ if (pcd->setup_pkt == NULL) {
-+ DWC_FREE(pcd);
-+ return NULL;
-+ }
-+
-+ pcd->status_buf = DWC_ALLOC(sizeof(uint16_t));
-+ if (pcd->status_buf == NULL) {
-+ DWC_FREE(pcd->setup_pkt);
-+ DWC_FREE(pcd);
-+ return NULL;
-+ }
-+ }
-+
-+ dwc_otg_pcd_reinit(pcd);
-+
-+ /* Allocate the cfi object for the PCD */
-+#ifdef DWC_UTE_CFI
-+ pcd->cfi = DWC_ALLOC(sizeof(cfiobject_t));
-+ if (NULL == pcd->cfi)
-+ goto fail;
-+ if (init_cfi(pcd->cfi)) {
-+ CFI_INFO("%s: Failed to init the CFI object\n", __func__);
-+ goto fail;
-+ }
-+#endif
-+
-+ /* Initialize tasklets */
-+ pcd->start_xfer_tasklet = DWC_TASK_ALLOC("xfer_tasklet",
-+ start_xfer_tasklet_func, pcd);
-+ pcd->test_mode_tasklet = DWC_TASK_ALLOC("test_mode_tasklet",
-+ do_test_mode, pcd);
-+
-+ /* Initialize SRP timer */
-+ core_if->srp_timer = DWC_TIMER_ALLOC("SRP TIMER", srp_timeout, core_if);
-+
-+ if (core_if->core_params->dev_out_nak) {
-+ /**
-+ * Initialize xfer timeout timer. Implemented for
-+ * 2.93a feature "Device DDMA OUT NAK Enhancement"
-+ */
-+ for(i = 0; i < MAX_EPS_CHANNELS; i++) {
-+ pcd->core_if->ep_xfer_timer[i] =
-+ DWC_TIMER_ALLOC("ep timer", ep_xfer_timeout,
-+ &pcd->core_if->ep_xfer_info[i]);
-+ }
-+ }
-+
-+ return pcd;
-+#ifdef DWC_UTE_CFI
-+fail:
-+#endif
-+ if (pcd->setup_pkt)
-+ DWC_FREE(pcd->setup_pkt);
-+ if (pcd->status_buf)
-+ DWC_FREE(pcd->status_buf);
-+#ifdef DWC_UTE_CFI
-+ if (pcd->cfi)
-+ DWC_FREE(pcd->cfi);
-+#endif
-+ if (pcd)
-+ DWC_FREE(pcd);
-+ return NULL;
-+
-+}
-+
-+/**
-+ * Remove PCD specific data
-+ */
-+void dwc_otg_pcd_remove(dwc_otg_pcd_t * pcd)
-+{
-+ dwc_otg_dev_if_t *dev_if = GET_CORE_IF(pcd)->dev_if;
-+ int i;
-+ if (pcd->core_if->core_params->dev_out_nak) {
-+ for (i = 0; i < MAX_EPS_CHANNELS; i++) {
-+ DWC_TIMER_CANCEL(pcd->core_if->ep_xfer_timer[i]);
-+ pcd->core_if->ep_xfer_info[i].state = 0;
-+ }
-+ }
-+
-+ if (GET_CORE_IF(pcd)->dma_enable) {
-+ DWC_DMA_FREE(sizeof(*pcd->setup_pkt) * 5, pcd->setup_pkt,
-+ pcd->setup_pkt_dma_handle);
-+ DWC_DMA_FREE(sizeof(uint16_t), pcd->status_buf,
-+ pcd->status_buf_dma_handle);
-+ if (GET_CORE_IF(pcd)->dma_desc_enable) {
-+ dwc_otg_ep_free_desc_chain(dev_if->setup_desc_addr[0],
-+ dev_if->dma_setup_desc_addr
-+ [0], 1);
-+ dwc_otg_ep_free_desc_chain(dev_if->setup_desc_addr[1],
-+ dev_if->dma_setup_desc_addr
-+ [1], 1);
-+ dwc_otg_ep_free_desc_chain(dev_if->in_desc_addr,
-+ dev_if->dma_in_desc_addr, 1);
-+ dwc_otg_ep_free_desc_chain(dev_if->out_desc_addr,
-+ dev_if->dma_out_desc_addr,
-+ 1);
-+ }
-+ } else {
-+ DWC_FREE(pcd->setup_pkt);
-+ DWC_FREE(pcd->status_buf);
-+ }
-+ DWC_SPINLOCK_FREE(pcd->lock);
-+ /* Set core_if's lock pointer to NULL */
-+ pcd->core_if->lock = NULL;
-+
-+ DWC_TASK_FREE(pcd->start_xfer_tasklet);
-+ DWC_TASK_FREE(pcd->test_mode_tasklet);
-+ if (pcd->core_if->core_params->dev_out_nak) {
-+ for (i = 0; i < MAX_EPS_CHANNELS; i++) {
-+ if (pcd->core_if->ep_xfer_timer[i]) {
-+ DWC_TIMER_FREE(pcd->core_if->ep_xfer_timer[i]);
-+ }
-+ }
-+ }
-+
-+/* Release the CFI object's dynamic memory */
-+#ifdef DWC_UTE_CFI
-+ if (pcd->cfi->ops.release) {
-+ pcd->cfi->ops.release(pcd->cfi);
-+ }
-+#endif
-+
-+ DWC_FREE(pcd);
-+}
-+
-+/**
-+ * Returns whether registered pcd is dual speed or not
-+ */
-+uint32_t dwc_otg_pcd_is_dualspeed(dwc_otg_pcd_t * pcd)
-+{
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+
-+ if ((core_if->core_params->speed == DWC_SPEED_PARAM_FULL) ||
-+ ((core_if->hwcfg2.b.hs_phy_type == 2) &&
-+ (core_if->hwcfg2.b.fs_phy_type == 1) &&
-+ (core_if->core_params->ulpi_fs_ls))) {
-+ return 0;
-+ }
-+
-+ return 1;
-+}
-+
-+/**
-+ * Returns whether registered pcd is OTG capable or not
-+ */
-+uint32_t dwc_otg_pcd_is_otg(dwc_otg_pcd_t * pcd)
-+{
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+ gusbcfg_data_t usbcfg = {.d32 = 0 };
-+
-+ usbcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->gusbcfg);
-+ if (!usbcfg.b.srpcap || !usbcfg.b.hnpcap) {
-+ return 0;
-+ }
-+
-+ return 1;
-+}
-+
-+/**
-+ * This function assigns periodic Tx FIFO to an periodic EP
-+ * in shared Tx FIFO mode
-+ */
-+static uint32_t assign_tx_fifo(dwc_otg_core_if_t * core_if)
-+{
-+ uint32_t TxMsk = 1;
-+ int i;
-+
-+ for (i = 0; i < core_if->hwcfg4.b.num_in_eps; ++i) {
-+ if ((TxMsk & core_if->tx_msk) == 0) {
-+ core_if->tx_msk |= TxMsk;
-+ return i + 1;
-+ }
-+ TxMsk <<= 1;
-+ }
-+ return 0;
-+}
-+
-+/**
-+ * This function assigns periodic Tx FIFO to an periodic EP
-+ * in shared Tx FIFO mode
-+ */
-+static uint32_t assign_perio_tx_fifo(dwc_otg_core_if_t * core_if)
-+{
-+ uint32_t PerTxMsk = 1;
-+ int i;
-+ for (i = 0; i < core_if->hwcfg4.b.num_dev_perio_in_ep; ++i) {
-+ if ((PerTxMsk & core_if->p_tx_msk) == 0) {
-+ core_if->p_tx_msk |= PerTxMsk;
-+ return i + 1;
-+ }
-+ PerTxMsk <<= 1;
-+ }
-+ return 0;
-+}
-+
-+/**
-+ * This function releases periodic Tx FIFO
-+ * in shared Tx FIFO mode
-+ */
-+static void release_perio_tx_fifo(dwc_otg_core_if_t * core_if,
-+ uint32_t fifo_num)
-+{
-+ core_if->p_tx_msk =
-+ (core_if->p_tx_msk & (1 << (fifo_num - 1))) ^ core_if->p_tx_msk;
-+}
-+
-+/**
-+ * This function releases periodic Tx FIFO
-+ * in shared Tx FIFO mode
-+ */
-+static void release_tx_fifo(dwc_otg_core_if_t * core_if, uint32_t fifo_num)
-+{
-+ core_if->tx_msk =
-+ (core_if->tx_msk & (1 << (fifo_num - 1))) ^ core_if->tx_msk;
-+}
-+
-+/**
-+ * This function is being called from gadget
-+ * to enable PCD endpoint.
-+ */
-+int dwc_otg_pcd_ep_enable(dwc_otg_pcd_t * pcd,
-+ const uint8_t * ep_desc, void *usb_ep)
-+{
-+ int num, dir;
-+ dwc_otg_pcd_ep_t *ep = NULL;
-+ const usb_endpoint_descriptor_t *desc;
-+ dwc_irqflags_t flags;
-+ fifosize_data_t dptxfsiz = {.d32 = 0 };
-+ gdfifocfg_data_t gdfifocfg = {.d32 = 0 };
-+ gdfifocfg_data_t gdfifocfgbase = {.d32 = 0 };
-+ int retval = 0;
-+ int i, epcount;
-+
-+ desc = (const usb_endpoint_descriptor_t *)ep_desc;
-+
-+ if (!desc) {
-+ pcd->ep0.priv = usb_ep;
-+ ep = &pcd->ep0;
-+ retval = -DWC_E_INVALID;
-+ goto out;
-+ }
-+
-+ num = UE_GET_ADDR(desc->bEndpointAddress);
-+ dir = UE_GET_DIR(desc->bEndpointAddress);
-+
-+ if (!desc->wMaxPacketSize) {
-+ DWC_WARN("bad maxpacketsize\n");
-+ retval = -DWC_E_INVALID;
-+ goto out;
-+ }
-+
-+ if (dir == UE_DIR_IN) {
-+ epcount = pcd->core_if->dev_if->num_in_eps;
-+ for (i = 0; i < epcount; i++) {
-+ if (num == pcd->in_ep[i].dwc_ep.num) {
-+ ep = &pcd->in_ep[i];
-+ break;
-+ }
-+ }
-+ } else {
-+ epcount = pcd->core_if->dev_if->num_out_eps;
-+ for (i = 0; i < epcount; i++) {
-+ if (num == pcd->out_ep[i].dwc_ep.num) {
-+ ep = &pcd->out_ep[i];
-+ break;
-+ }
-+ }
-+ }
-+
-+ if (!ep) {
-+ DWC_WARN("bad address\n");
-+ retval = -DWC_E_INVALID;
-+ goto out;
-+ }
-+
-+ DWC_SPINLOCK_IRQSAVE(pcd->lock, &flags);
-+
-+ ep->desc = desc;
-+ ep->priv = usb_ep;
-+
-+ /*
-+ * Activate the EP
-+ */
-+ ep->stopped = 0;
-+
-+ ep->dwc_ep.is_in = (dir == UE_DIR_IN);
-+ ep->dwc_ep.maxpacket = UGETW(desc->wMaxPacketSize);
-+
-+ ep->dwc_ep.type = desc->bmAttributes & UE_XFERTYPE;
-+
-+ if (ep->dwc_ep.is_in) {
-+ if (!GET_CORE_IF(pcd)->en_multiple_tx_fifo) {
-+ ep->dwc_ep.tx_fifo_num = 0;
-+
-+ if (ep->dwc_ep.type == UE_ISOCHRONOUS) {
-+ /*
-+ * if ISOC EP then assign a Periodic Tx FIFO.
-+ */
-+ ep->dwc_ep.tx_fifo_num =
-+ assign_perio_tx_fifo(GET_CORE_IF(pcd));
-+ }
-+ } else {
-+ /*
-+ * if Dedicated FIFOs mode is on then assign a Tx FIFO.
-+ */
-+ ep->dwc_ep.tx_fifo_num =
-+ assign_tx_fifo(GET_CORE_IF(pcd));
-+ }
-+
-+ /* Calculating EP info controller base address */
-+ if (ep->dwc_ep.tx_fifo_num
-+ && GET_CORE_IF(pcd)->en_multiple_tx_fifo) {
-+ gdfifocfg.d32 =
-+ DWC_READ_REG32(&GET_CORE_IF(pcd)->
-+ core_global_regs->gdfifocfg);
-+ gdfifocfgbase.d32 = gdfifocfg.d32 >> 16;
-+ dptxfsiz.d32 =
-+ (DWC_READ_REG32
-+ (&GET_CORE_IF(pcd)->core_global_regs->
-+ dtxfsiz[ep->dwc_ep.tx_fifo_num - 1]) >> 16);
-+ gdfifocfg.b.epinfobase =
-+ gdfifocfgbase.d32 + dptxfsiz.d32;
-+ if (GET_CORE_IF(pcd)->snpsid <= OTG_CORE_REV_2_94a) {
-+ DWC_WRITE_REG32(&GET_CORE_IF(pcd)->
-+ core_global_regs->gdfifocfg,
-+ gdfifocfg.d32);
-+ }
-+ }
-+ }
-+ /* Set initial data PID. */
-+ if (ep->dwc_ep.type == UE_BULK) {
-+ ep->dwc_ep.data_pid_start = 0;
-+ }
-+
-+ /* Alloc DMA Descriptors */
-+ if (GET_CORE_IF(pcd)->dma_desc_enable) {
-+#ifndef DWC_UTE_PER_IO
-+ if (ep->dwc_ep.type != UE_ISOCHRONOUS) {
-+#endif
-+ ep->dwc_ep.desc_addr =
-+ dwc_otg_ep_alloc_desc_chain(&ep->
-+ dwc_ep.dma_desc_addr,
-+ MAX_DMA_DESC_CNT);
-+ if (!ep->dwc_ep.desc_addr) {
-+ DWC_WARN("%s, can't allocate DMA descriptor\n",
-+ __func__);
-+ retval = -DWC_E_SHUTDOWN;
-+ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags);
-+ goto out;
-+ }
-+#ifndef DWC_UTE_PER_IO
-+ }
-+#endif
-+ }
-+
-+ DWC_DEBUGPL(DBG_PCD, "Activate %s: type=%d, mps=%d desc=%p\n",
-+ (ep->dwc_ep.is_in ? "IN" : "OUT"),
-+ ep->dwc_ep.type, ep->dwc_ep.maxpacket, ep->desc);
-+#ifdef DWC_UTE_PER_IO
-+ ep->dwc_ep.xiso_bInterval = 1 << (ep->desc->bInterval - 1);
-+#endif
-+ if (ep->dwc_ep.type == DWC_OTG_EP_TYPE_ISOC) {
-+ ep->dwc_ep.bInterval = 1 << (ep->desc->bInterval - 1);
-+ ep->dwc_ep.frame_num = 0xFFFFFFFF;
-+ }
-+
-+ dwc_otg_ep_activate(GET_CORE_IF(pcd), &ep->dwc_ep);
-+
-+#ifdef DWC_UTE_CFI
-+ if (pcd->cfi->ops.ep_enable) {
-+ pcd->cfi->ops.ep_enable(pcd->cfi, pcd, ep);
-+ }
-+#endif
-+
-+ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags);
-+
-+out:
-+ return retval;
-+}
-+
-+/**
-+ * This function is being called from gadget
-+ * to disable PCD endpoint.
-+ */
-+int dwc_otg_pcd_ep_disable(dwc_otg_pcd_t * pcd, void *ep_handle)
-+{
-+ dwc_otg_pcd_ep_t *ep;
-+ dwc_irqflags_t flags;
-+ dwc_otg_dev_dma_desc_t *desc_addr;
-+ dwc_dma_t dma_desc_addr;
-+ gdfifocfg_data_t gdfifocfgbase = {.d32 = 0 };
-+ gdfifocfg_data_t gdfifocfg = {.d32 = 0 };
-+ fifosize_data_t dptxfsiz = {.d32 = 0 };
-+
-+ ep = get_ep_from_handle(pcd, ep_handle);
-+
-+ if (!ep || !ep->desc) {
-+ DWC_DEBUGPL(DBG_PCD, "bad ep address\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ DWC_SPINLOCK_IRQSAVE(pcd->lock, &flags);
-+
-+ dwc_otg_request_nuke(ep);
-+
-+ dwc_otg_ep_deactivate(GET_CORE_IF(pcd), &ep->dwc_ep);
-+ if (pcd->core_if->core_params->dev_out_nak) {
-+ DWC_TIMER_CANCEL(pcd->core_if->ep_xfer_timer[ep->dwc_ep.num]);
-+ pcd->core_if->ep_xfer_info[ep->dwc_ep.num].state = 0;
-+ }
-+ ep->desc = NULL;
-+ ep->stopped = 1;
-+
-+ gdfifocfg.d32 =
-+ DWC_READ_REG32(&GET_CORE_IF(pcd)->core_global_regs->gdfifocfg);
-+ gdfifocfgbase.d32 = gdfifocfg.d32 >> 16;
-+
-+ if (ep->dwc_ep.is_in) {
-+ if (GET_CORE_IF(pcd)->en_multiple_tx_fifo) {
-+ /* Flush the Tx FIFO */
-+ dwc_otg_flush_tx_fifo(GET_CORE_IF(pcd),
-+ ep->dwc_ep.tx_fifo_num);
-+ }
-+ release_perio_tx_fifo(GET_CORE_IF(pcd), ep->dwc_ep.tx_fifo_num);
-+ release_tx_fifo(GET_CORE_IF(pcd), ep->dwc_ep.tx_fifo_num);
-+ if (GET_CORE_IF(pcd)->en_multiple_tx_fifo) {
-+ /* Decreasing EPinfo Base Addr */
-+ dptxfsiz.d32 =
-+ (DWC_READ_REG32
-+ (&GET_CORE_IF(pcd)->
-+ core_global_regs->dtxfsiz[ep->dwc_ep.tx_fifo_num-1]) >> 16);
-+ gdfifocfg.b.epinfobase = gdfifocfgbase.d32 - dptxfsiz.d32;
-+ if (GET_CORE_IF(pcd)->snpsid <= OTG_CORE_REV_2_94a) {
-+ DWC_WRITE_REG32(&GET_CORE_IF(pcd)->core_global_regs->gdfifocfg,
-+ gdfifocfg.d32);
-+ }
-+ }
-+ }
-+
-+ /* Free DMA Descriptors */
-+ if (GET_CORE_IF(pcd)->dma_desc_enable) {
-+ if (ep->dwc_ep.type != UE_ISOCHRONOUS) {
-+ desc_addr = ep->dwc_ep.desc_addr;
-+ dma_desc_addr = ep->dwc_ep.dma_desc_addr;
-+
-+ /* Cannot call dma_free_coherent() with IRQs disabled */
-+ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags);
-+ dwc_otg_ep_free_desc_chain(desc_addr, dma_desc_addr,
-+ MAX_DMA_DESC_CNT);
-+
-+ goto out_unlocked;
-+ }
-+ }
-+ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags);
-+
-+out_unlocked:
-+ DWC_DEBUGPL(DBG_PCD, "%d %s disabled\n", ep->dwc_ep.num,
-+ ep->dwc_ep.is_in ? "IN" : "OUT");
-+ return 0;
-+
-+}
-+
-+/******************************************************************************/
-+#ifdef DWC_UTE_PER_IO
-+
-+/**
-+ * Free the request and its extended parts
-+ *
-+ */
-+void dwc_pcd_xiso_ereq_free(dwc_otg_pcd_ep_t * ep, dwc_otg_pcd_request_t * req)
-+{
-+ DWC_FREE(req->ext_req.per_io_frame_descs);
-+ DWC_FREE(req);
-+}
-+
-+/**
-+ * Start the next request in the endpoint's queue.
-+ *
-+ */
-+int dwc_otg_pcd_xiso_start_next_request(dwc_otg_pcd_t * pcd,
-+ dwc_otg_pcd_ep_t * ep)
-+{
-+ int i;
-+ dwc_otg_pcd_request_t *req = NULL;
-+ dwc_ep_t *dwcep = NULL;
-+ struct dwc_iso_xreq_port *ereq = NULL;
-+ struct dwc_iso_pkt_desc_port *ddesc_iso;
-+ uint16_t nat;
-+ depctl_data_t diepctl;
-+
-+ dwcep = &ep->dwc_ep;
-+
-+ if (dwcep->xiso_active_xfers > 0) {
-+#if 0 //Disable this to decrease s/w overhead that is crucial for Isoc transfers
-+ DWC_WARN("There are currently active transfers for EP%d \
-+ (active=%d; queued=%d)", dwcep->num, dwcep->xiso_active_xfers,
-+ dwcep->xiso_queued_xfers);
-+#endif
-+ return 0;
-+ }
-+
-+ nat = UGETW(ep->desc->wMaxPacketSize);
-+ nat = (nat >> 11) & 0x03;
-+
-+ if (!DWC_CIRCLEQ_EMPTY(&ep->queue)) {
-+ req = DWC_CIRCLEQ_FIRST(&ep->queue);
-+ ereq = &req->ext_req;
-+ ep->stopped = 0;
-+
-+ /* Get the frame number */
-+ dwcep->xiso_frame_num =
-+ dwc_otg_get_frame_number(GET_CORE_IF(pcd));
-+ DWC_DEBUG("FRM_NUM=%d", dwcep->xiso_frame_num);
-+
-+ ddesc_iso = ereq->per_io_frame_descs;
-+
-+ if (dwcep->is_in) {
-+ /* Setup DMA Descriptor chain for IN Isoc request */
-+ for (i = 0; i < ereq->pio_pkt_count; i++) {
-+ //if ((i % (nat + 1)) == 0)
-+ if ( i > 0 )
-+ dwcep->xiso_frame_num =
-+ (dwcep->xiso_bInterval +
-+ dwcep->xiso_frame_num) & 0x3FFF;
-+ dwcep->desc_addr[i].buf =
-+ req->dma + ddesc_iso[i].offset;
-+ dwcep->desc_addr[i].status.b_iso_in.txbytes =
-+ ddesc_iso[i].length;
-+ dwcep->desc_addr[i].status.b_iso_in.framenum =
-+ dwcep->xiso_frame_num;
-+ dwcep->desc_addr[i].status.b_iso_in.bs =
-+ BS_HOST_READY;
-+ dwcep->desc_addr[i].status.b_iso_in.txsts = 0;
-+ dwcep->desc_addr[i].status.b_iso_in.sp =
-+ (ddesc_iso[i].length %
-+ dwcep->maxpacket) ? 1 : 0;
-+ dwcep->desc_addr[i].status.b_iso_in.ioc = 0;
-+ dwcep->desc_addr[i].status.b_iso_in.pid = nat + 1;
-+ dwcep->desc_addr[i].status.b_iso_in.l = 0;
-+
-+ /* Process the last descriptor */
-+ if (i == ereq->pio_pkt_count - 1) {
-+ dwcep->desc_addr[i].status.b_iso_in.ioc = 1;
-+ dwcep->desc_addr[i].status.b_iso_in.l = 1;
-+ }
-+ }
-+
-+ /* Setup and start the transfer for this endpoint */
-+ dwcep->xiso_active_xfers++;
-+ DWC_WRITE_REG32(&GET_CORE_IF(pcd)->dev_if->
-+ in_ep_regs[dwcep->num]->diepdma,
-+ dwcep->dma_desc_addr);
-+ diepctl.d32 = 0;
-+ diepctl.b.epena = 1;
-+ diepctl.b.cnak = 1;
-+ DWC_MODIFY_REG32(&GET_CORE_IF(pcd)->dev_if->
-+ in_ep_regs[dwcep->num]->diepctl, 0,
-+ diepctl.d32);
-+ } else {
-+ /* Setup DMA Descriptor chain for OUT Isoc request */
-+ for (i = 0; i < ereq->pio_pkt_count; i++) {
-+ //if ((i % (nat + 1)) == 0)
-+ dwcep->xiso_frame_num = (dwcep->xiso_bInterval +
-+ dwcep->xiso_frame_num) & 0x3FFF;
-+ dwcep->desc_addr[i].buf =
-+ req->dma + ddesc_iso[i].offset;
-+ dwcep->desc_addr[i].status.b_iso_out.rxbytes =
-+ ddesc_iso[i].length;
-+ dwcep->desc_addr[i].status.b_iso_out.framenum =
-+ dwcep->xiso_frame_num;
-+ dwcep->desc_addr[i].status.b_iso_out.bs =
-+ BS_HOST_READY;
-+ dwcep->desc_addr[i].status.b_iso_out.rxsts = 0;
-+ dwcep->desc_addr[i].status.b_iso_out.sp =
-+ (ddesc_iso[i].length %
-+ dwcep->maxpacket) ? 1 : 0;
-+ dwcep->desc_addr[i].status.b_iso_out.ioc = 0;
-+ dwcep->desc_addr[i].status.b_iso_out.pid = nat + 1;
-+ dwcep->desc_addr[i].status.b_iso_out.l = 0;
-+
-+ /* Process the last descriptor */
-+ if (i == ereq->pio_pkt_count - 1) {
-+ dwcep->desc_addr[i].status.b_iso_out.ioc = 1;
-+ dwcep->desc_addr[i].status.b_iso_out.l = 1;
-+ }
-+ }
-+
-+ /* Setup and start the transfer for this endpoint */
-+ dwcep->xiso_active_xfers++;
-+ DWC_WRITE_REG32(&GET_CORE_IF(pcd)->
-+ dev_if->out_ep_regs[dwcep->num]->
-+ doepdma, dwcep->dma_desc_addr);
-+ diepctl.d32 = 0;
-+ diepctl.b.epena = 1;
-+ diepctl.b.cnak = 1;
-+ DWC_MODIFY_REG32(&GET_CORE_IF(pcd)->
-+ dev_if->out_ep_regs[dwcep->num]->
-+ doepctl, 0, diepctl.d32);
-+ }
-+
-+ } else {
-+ ep->stopped = 1;
-+ }
-+
-+ return 0;
-+}
-+
-+/**
-+ * - Remove the request from the queue
-+ */
-+void complete_xiso_ep(dwc_otg_pcd_ep_t * ep)
-+{
-+ dwc_otg_pcd_request_t *req = NULL;
-+ struct dwc_iso_xreq_port *ereq = NULL;
-+ struct dwc_iso_pkt_desc_port *ddesc_iso = NULL;
-+ dwc_ep_t *dwcep = NULL;
-+ int i;
-+
-+ //DWC_DEBUG();
-+ dwcep = &ep->dwc_ep;
-+
-+ /* Get the first pending request from the queue */
-+ if (!DWC_CIRCLEQ_EMPTY(&ep->queue)) {
-+ req = DWC_CIRCLEQ_FIRST(&ep->queue);
-+ if (!req) {
-+ DWC_PRINTF("complete_ep 0x%p, req = NULL!\n", ep);
-+ return;
-+ }
-+ dwcep->xiso_active_xfers--;
-+ dwcep->xiso_queued_xfers--;
-+ /* Remove this request from the queue */
-+ DWC_CIRCLEQ_REMOVE_INIT(&ep->queue, req, queue_entry);
-+ } else {
-+ DWC_PRINTF("complete_ep 0x%p, ep->queue empty!\n", ep);
-+ return;
-+ }
-+
-+ ep->stopped = 1;
-+ ereq = &req->ext_req;
-+ ddesc_iso = ereq->per_io_frame_descs;
-+
-+ if (dwcep->xiso_active_xfers < 0) {
-+ DWC_WARN("EP#%d (xiso_active_xfers=%d)", dwcep->num,
-+ dwcep->xiso_active_xfers);
-+ }
-+
-+ /* Fill the Isoc descs of portable extended req from dma descriptors */
-+ for (i = 0; i < ereq->pio_pkt_count; i++) {
-+ if (dwcep->is_in) { /* IN endpoints */
-+ ddesc_iso[i].actual_length = ddesc_iso[i].length -
-+ dwcep->desc_addr[i].status.b_iso_in.txbytes;
-+ ddesc_iso[i].status =
-+ dwcep->desc_addr[i].status.b_iso_in.txsts;
-+ } else { /* OUT endpoints */
-+ ddesc_iso[i].actual_length = ddesc_iso[i].length -
-+ dwcep->desc_addr[i].status.b_iso_out.rxbytes;
-+ ddesc_iso[i].status =
-+ dwcep->desc_addr[i].status.b_iso_out.rxsts;
-+ }
-+ }
-+
-+ DWC_SPINUNLOCK(ep->pcd->lock);
-+
-+ /* Call the completion function in the non-portable logic */
-+ ep->pcd->fops->xisoc_complete(ep->pcd, ep->priv, req->priv, 0,
-+ &req->ext_req);
-+
-+ DWC_SPINLOCK(ep->pcd->lock);
-+
-+ /* Free the request - specific freeing needed for extended request object */
-+ dwc_pcd_xiso_ereq_free(ep, req);
-+
-+ /* Start the next request */
-+ dwc_otg_pcd_xiso_start_next_request(ep->pcd, ep);
-+
-+ return;
-+}
-+
-+/**
-+ * Create and initialize the Isoc pkt descriptors of the extended request.
-+ *
-+ */
-+static int dwc_otg_pcd_xiso_create_pkt_descs(dwc_otg_pcd_request_t * req,
-+ void *ereq_nonport,
-+ int atomic_alloc)
-+{
-+ struct dwc_iso_xreq_port *ereq = NULL;
-+ struct dwc_iso_xreq_port *req_mapped = NULL;
-+ struct dwc_iso_pkt_desc_port *ipds = NULL; /* To be created in this function */
-+ uint32_t pkt_count;
-+ int i;
-+
-+ ereq = &req->ext_req;
-+ req_mapped = (struct dwc_iso_xreq_port *)ereq_nonport;
-+ pkt_count = req_mapped->pio_pkt_count;
-+
-+ /* Create the isoc descs */
-+ if (atomic_alloc) {
-+ ipds = DWC_ALLOC_ATOMIC(sizeof(*ipds) * pkt_count);
-+ } else {
-+ ipds = DWC_ALLOC(sizeof(*ipds) * pkt_count);
-+ }
-+
-+ if (!ipds) {
-+ DWC_ERROR("Failed to allocate isoc descriptors");
-+ return -DWC_E_NO_MEMORY;
-+ }
-+
-+ /* Initialize the extended request fields */
-+ ereq->per_io_frame_descs = ipds;
-+ ereq->error_count = 0;
-+ ereq->pio_alloc_pkt_count = pkt_count;
-+ ereq->pio_pkt_count = pkt_count;
-+ ereq->tr_sub_flags = req_mapped->tr_sub_flags;
-+
-+ /* Init the Isoc descriptors */
-+ for (i = 0; i < pkt_count; i++) {
-+ ipds[i].length = req_mapped->per_io_frame_descs[i].length;
-+ ipds[i].offset = req_mapped->per_io_frame_descs[i].offset;
-+ ipds[i].status = req_mapped->per_io_frame_descs[i].status; /* 0 */
-+ ipds[i].actual_length =
-+ req_mapped->per_io_frame_descs[i].actual_length;
-+ }
-+
-+ return 0;
-+}
-+
-+static void prn_ext_request(struct dwc_iso_xreq_port *ereq)
-+{
-+ struct dwc_iso_pkt_desc_port *xfd = NULL;
-+ int i;
-+
-+ DWC_DEBUG("per_io_frame_descs=%p", ereq->per_io_frame_descs);
-+ DWC_DEBUG("tr_sub_flags=%d", ereq->tr_sub_flags);
-+ DWC_DEBUG("error_count=%d", ereq->error_count);
-+ DWC_DEBUG("pio_alloc_pkt_count=%d", ereq->pio_alloc_pkt_count);
-+ DWC_DEBUG("pio_pkt_count=%d", ereq->pio_pkt_count);
-+ DWC_DEBUG("res=%d", ereq->res);
-+
-+ for (i = 0; i < ereq->pio_pkt_count; i++) {
-+ xfd = &ereq->per_io_frame_descs[0];
-+ DWC_DEBUG("FD #%d", i);
-+
-+ DWC_DEBUG("xfd->actual_length=%d", xfd->actual_length);
-+ DWC_DEBUG("xfd->length=%d", xfd->length);
-+ DWC_DEBUG("xfd->offset=%d", xfd->offset);
-+ DWC_DEBUG("xfd->status=%d", xfd->status);
-+ }
-+}
-+
-+/**
-+ *
-+ */
-+int dwc_otg_pcd_xiso_ep_queue(dwc_otg_pcd_t * pcd, void *ep_handle,
-+ uint8_t * buf, dwc_dma_t dma_buf, uint32_t buflen,
-+ int zero, void *req_handle, int atomic_alloc,
-+ void *ereq_nonport)
-+{
-+ dwc_otg_pcd_request_t *req = NULL;
-+ dwc_otg_pcd_ep_t *ep;
-+ dwc_irqflags_t flags;
-+ int res;
-+
-+ ep = get_ep_from_handle(pcd, ep_handle);
-+ if (!ep) {
-+ DWC_WARN("bad ep\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ /* We support this extension only for DDMA mode */
-+ if (ep->dwc_ep.type == DWC_OTG_EP_TYPE_ISOC)
-+ if (!GET_CORE_IF(pcd)->dma_desc_enable)
-+ return -DWC_E_INVALID;
-+
-+ /* Create a dwc_otg_pcd_request_t object */
-+ if (atomic_alloc) {
-+ req = DWC_ALLOC_ATOMIC(sizeof(*req));
-+ } else {
-+ req = DWC_ALLOC(sizeof(*req));
-+ }
-+
-+ if (!req) {
-+ return -DWC_E_NO_MEMORY;
-+ }
-+
-+ /* Create the Isoc descs for this request which shall be the exact match
-+ * of the structure sent to us from the non-portable logic */
-+ res =
-+ dwc_otg_pcd_xiso_create_pkt_descs(req, ereq_nonport, atomic_alloc);
-+ if (res) {
-+ DWC_WARN("Failed to init the Isoc descriptors");
-+ DWC_FREE(req);
-+ return res;
-+ }
-+
-+ DWC_SPINLOCK_IRQSAVE(pcd->lock, &flags);
-+
-+ DWC_CIRCLEQ_INIT_ENTRY(req, queue_entry);
-+ req->buf = buf;
-+ req->dma = dma_buf;
-+ req->length = buflen;
-+ req->sent_zlp = zero;
-+ req->priv = req_handle;
-+
-+ //DWC_SPINLOCK_IRQSAVE(pcd->lock, &flags);
-+ ep->dwc_ep.dma_addr = dma_buf;
-+ ep->dwc_ep.start_xfer_buff = buf;
-+ ep->dwc_ep.xfer_buff = buf;
-+ ep->dwc_ep.xfer_len = 0;
-+ ep->dwc_ep.xfer_count = 0;
-+ ep->dwc_ep.sent_zlp = 0;
-+ ep->dwc_ep.total_len = buflen;
-+
-+ /* Add this request to the tail */
-+ DWC_CIRCLEQ_INSERT_TAIL(&ep->queue, req, queue_entry);
-+ ep->dwc_ep.xiso_queued_xfers++;
-+
-+//DWC_DEBUG("CP_0");
-+//DWC_DEBUG("req->ext_req.tr_sub_flags=%d", req->ext_req.tr_sub_flags);
-+//prn_ext_request((struct dwc_iso_xreq_port *) ereq_nonport);
-+//prn_ext_request(&req->ext_req);
-+
-+ //DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags);
-+
-+ /* If the req->status == ASAP then check if there is any active transfer
-+ * for this endpoint. If no active transfers, then get the first entry
-+ * from the queue and start that transfer
-+ */
-+ if (req->ext_req.tr_sub_flags == DWC_EREQ_TF_ASAP) {
-+ res = dwc_otg_pcd_xiso_start_next_request(pcd, ep);
-+ if (res) {
-+ DWC_WARN("Failed to start the next Isoc transfer");
-+ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags);
-+ DWC_FREE(req);
-+ return res;
-+ }
-+ }
-+
-+ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags);
-+ return 0;
-+}
-+
-+#endif
-+/* END ifdef DWC_UTE_PER_IO ***************************************************/
-+int dwc_otg_pcd_ep_queue(dwc_otg_pcd_t * pcd, void *ep_handle,
-+ uint8_t * buf, dwc_dma_t dma_buf, uint32_t buflen,
-+ int zero, void *req_handle, int atomic_alloc)
-+{
-+ dwc_irqflags_t flags;
-+ dwc_otg_pcd_request_t *req;
-+ dwc_otg_pcd_ep_t *ep;
-+ uint32_t max_transfer;
-+
-+ ep = get_ep_from_handle(pcd, ep_handle);
-+ if (!ep || (!ep->desc && ep->dwc_ep.num != 0)) {
-+ DWC_WARN("bad ep\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if (atomic_alloc) {
-+ req = DWC_ALLOC_ATOMIC(sizeof(*req));
-+ } else {
-+ req = DWC_ALLOC(sizeof(*req));
-+ }
-+
-+ if (!req) {
-+ return -DWC_E_NO_MEMORY;
-+ }
-+ DWC_CIRCLEQ_INIT_ENTRY(req, queue_entry);
-+ if (!GET_CORE_IF(pcd)->core_params->opt) {
-+ if (ep->dwc_ep.num != 0) {
-+ DWC_ERROR("queue req %p, len %d buf %p\n",
-+ req_handle, buflen, buf);
-+ }
-+ }
-+
-+ req->buf = buf;
-+ req->dma = dma_buf;
-+ req->length = buflen;
-+ req->sent_zlp = zero;
-+ req->priv = req_handle;
-+ req->dw_align_buf = NULL;
-+ if ((dma_buf & 0x3) && GET_CORE_IF(pcd)->dma_enable
-+ && !GET_CORE_IF(pcd)->dma_desc_enable)
-+ req->dw_align_buf = DWC_DMA_ALLOC(buflen,
-+ &req->dw_align_buf_dma);
-+ DWC_SPINLOCK_IRQSAVE(pcd->lock, &flags);
-+
-+ /*
-+ * After adding request to the queue for IN ISOC wait for In Token Received
-+ * when TX FIFO is empty interrupt and for OUT ISOC wait for OUT Token
-+ * Received when EP is disabled interrupt to obtain starting microframe
-+ * (odd/even) start transfer
-+ */
-+ if (ep->dwc_ep.type == DWC_OTG_EP_TYPE_ISOC) {
-+ if (req != 0) {
-+ depctl_data_t depctl = {.d32 =
-+ DWC_READ_REG32(&pcd->core_if->dev_if->
-+ in_ep_regs[ep->dwc_ep.num]->
-+ diepctl) };
-+ ++pcd->request_pending;
-+
-+ DWC_CIRCLEQ_INSERT_TAIL(&ep->queue, req, queue_entry);
-+ if (ep->dwc_ep.is_in) {
-+ depctl.b.cnak = 1;
-+ DWC_WRITE_REG32(&pcd->core_if->dev_if->
-+ in_ep_regs[ep->dwc_ep.num]->
-+ diepctl, depctl.d32);
-+ }
-+
-+ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags);
-+ }
-+ return 0;
-+ }
-+
-+ /*
-+ * For EP0 IN without premature status, zlp is required?
-+ */
-+ if (ep->dwc_ep.num == 0 && ep->dwc_ep.is_in) {
-+ DWC_DEBUGPL(DBG_PCDV, "%d-OUT ZLP\n", ep->dwc_ep.num);
-+ //_req->zero = 1;
-+ }
-+
-+ /* Start the transfer */
-+ if (DWC_CIRCLEQ_EMPTY(&ep->queue) && !ep->stopped) {
-+ /* EP0 Transfer? */
-+ if (ep->dwc_ep.num == 0) {
-+ switch (pcd->ep0state) {
-+ case EP0_IN_DATA_PHASE:
-+ DWC_DEBUGPL(DBG_PCD,
-+ "%s ep0: EP0_IN_DATA_PHASE\n",
-+ __func__);
-+ break;
-+
-+ case EP0_OUT_DATA_PHASE:
-+ DWC_DEBUGPL(DBG_PCD,
-+ "%s ep0: EP0_OUT_DATA_PHASE\n",
-+ __func__);
-+ if (pcd->request_config) {
-+ /* Complete STATUS PHASE */
-+ ep->dwc_ep.is_in = 1;
-+ pcd->ep0state = EP0_IN_STATUS_PHASE;
-+ }
-+ break;
-+
-+ case EP0_IN_STATUS_PHASE:
-+ DWC_DEBUGPL(DBG_PCD,
-+ "%s ep0: EP0_IN_STATUS_PHASE\n",
-+ __func__);
-+ break;
-+
-+ default:
-+ DWC_DEBUGPL(DBG_ANY, "ep0: odd state %d\n",
-+ pcd->ep0state);
-+ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags);
-+ return -DWC_E_SHUTDOWN;
-+ }
-+
-+ ep->dwc_ep.dma_addr = dma_buf;
-+ ep->dwc_ep.start_xfer_buff = buf;
-+ ep->dwc_ep.xfer_buff = buf;
-+ ep->dwc_ep.xfer_len = buflen;
-+ ep->dwc_ep.xfer_count = 0;
-+ ep->dwc_ep.sent_zlp = 0;
-+ ep->dwc_ep.total_len = ep->dwc_ep.xfer_len;
-+
-+ if (zero) {
-+ if ((ep->dwc_ep.xfer_len %
-+ ep->dwc_ep.maxpacket == 0)
-+ && (ep->dwc_ep.xfer_len != 0)) {
-+ ep->dwc_ep.sent_zlp = 1;
-+ }
-+
-+ }
-+
-+ dwc_otg_ep0_start_transfer(GET_CORE_IF(pcd),
-+ &ep->dwc_ep);
-+ } // non-ep0 endpoints
-+ else {
-+#ifdef DWC_UTE_CFI
-+ if (ep->dwc_ep.buff_mode != BM_STANDARD) {
-+ /* store the request length */
-+ ep->dwc_ep.cfi_req_len = buflen;
-+ pcd->cfi->ops.build_descriptors(pcd->cfi, pcd,
-+ ep, req);
-+ } else {
-+#endif
-+ max_transfer =
-+ GET_CORE_IF(ep->pcd)->core_params->
-+ max_transfer_size;
-+
-+ /* Setup and start the Transfer */
-+ if (req->dw_align_buf){
-+ if (ep->dwc_ep.is_in)
-+ dwc_memcpy(req->dw_align_buf,
-+ buf, buflen);
-+ ep->dwc_ep.dma_addr =
-+ req->dw_align_buf_dma;
-+ ep->dwc_ep.start_xfer_buff =
-+ req->dw_align_buf;
-+ ep->dwc_ep.xfer_buff =
-+ req->dw_align_buf;
-+ } else {
-+ ep->dwc_ep.dma_addr = dma_buf;
-+ ep->dwc_ep.start_xfer_buff = buf;
-+ ep->dwc_ep.xfer_buff = buf;
-+ }
-+ ep->dwc_ep.xfer_len = 0;
-+ ep->dwc_ep.xfer_count = 0;
-+ ep->dwc_ep.sent_zlp = 0;
-+ ep->dwc_ep.total_len = buflen;
-+
-+ ep->dwc_ep.maxxfer = max_transfer;
-+ if (GET_CORE_IF(pcd)->dma_desc_enable) {
-+ uint32_t out_max_xfer =
-+ DDMA_MAX_TRANSFER_SIZE -
-+ (DDMA_MAX_TRANSFER_SIZE % 4);
-+ if (ep->dwc_ep.is_in) {
-+ if (ep->dwc_ep.maxxfer >
-+ DDMA_MAX_TRANSFER_SIZE) {
-+ ep->dwc_ep.maxxfer =
-+ DDMA_MAX_TRANSFER_SIZE;
-+ }
-+ } else {
-+ if (ep->dwc_ep.maxxfer >
-+ out_max_xfer) {
-+ ep->dwc_ep.maxxfer =
-+ out_max_xfer;
-+ }
-+ }
-+ }
-+ if (ep->dwc_ep.maxxfer < ep->dwc_ep.total_len) {
-+ ep->dwc_ep.maxxfer -=
-+ (ep->dwc_ep.maxxfer %
-+ ep->dwc_ep.maxpacket);
-+ }
-+
-+ if (zero) {
-+ if ((ep->dwc_ep.total_len %
-+ ep->dwc_ep.maxpacket == 0)
-+ && (ep->dwc_ep.total_len != 0)) {
-+ ep->dwc_ep.sent_zlp = 1;
-+ }
-+ }
-+#ifdef DWC_UTE_CFI
-+ }
-+#endif
-+ dwc_otg_ep_start_transfer(GET_CORE_IF(pcd),
-+ &ep->dwc_ep);
-+ }
-+ }
-+
-+ if (req != 0) {
-+ ++pcd->request_pending;
-+ DWC_CIRCLEQ_INSERT_TAIL(&ep->queue, req, queue_entry);
-+ if (ep->dwc_ep.is_in && ep->stopped
-+ && !(GET_CORE_IF(pcd)->dma_enable)) {
-+ /** @todo NGS Create a function for this. */
-+ diepmsk_data_t diepmsk = {.d32 = 0 };
-+ diepmsk.b.intktxfemp = 1;
-+ if (GET_CORE_IF(pcd)->multiproc_int_enable) {
-+ DWC_MODIFY_REG32(&GET_CORE_IF(pcd)->
-+ dev_if->dev_global_regs->diepeachintmsk
-+ [ep->dwc_ep.num], 0,
-+ diepmsk.d32);
-+ } else {
-+ DWC_MODIFY_REG32(&GET_CORE_IF(pcd)->
-+ dev_if->dev_global_regs->
-+ diepmsk, 0, diepmsk.d32);
-+ }
-+
-+ }
-+ }
-+ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags);
-+
-+ return 0;
-+}
-+
-+int dwc_otg_pcd_ep_dequeue(dwc_otg_pcd_t * pcd, void *ep_handle,
-+ void *req_handle)
-+{
-+ dwc_irqflags_t flags;
-+ dwc_otg_pcd_request_t *req;
-+ dwc_otg_pcd_ep_t *ep;
-+
-+ ep = get_ep_from_handle(pcd, ep_handle);
-+ if (!ep || (!ep->desc && ep->dwc_ep.num != 0)) {
-+ DWC_WARN("bad argument\n");
-+ return -DWC_E_INVALID;
-+ }
-+
-+ DWC_SPINLOCK_IRQSAVE(pcd->lock, &flags);
-+
-+ /* make sure it's actually queued on this endpoint */
-+ DWC_CIRCLEQ_FOREACH(req, &ep->queue, queue_entry) {
-+ if (req->priv == (void *)req_handle) {
-+ break;
-+ }
-+ }
-+
-+ if (req->priv != (void *)req_handle) {
-+ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags);
-+ return -DWC_E_INVALID;
-+ }
-+
-+ if (!DWC_CIRCLEQ_EMPTY_ENTRY(req, queue_entry)) {
-+ dwc_otg_request_done(ep, req, -DWC_E_RESTART);
-+ } else {
-+ req = NULL;
-+ }
-+
-+ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags);
-+
-+ return req ? 0 : -DWC_E_SHUTDOWN;
-+
-+}
-+
-+/**
-+ * dwc_otg_pcd_ep_wedge - sets the halt feature and ignores clear requests
-+ *
-+ * Use this to stall an endpoint and ignore CLEAR_FEATURE(HALT_ENDPOINT)
-+ * requests. If the gadget driver clears the halt status, it will
-+ * automatically unwedge the endpoint.
-+ *
-+ * Returns zero on success, else negative DWC error code.
-+ */
-+int dwc_otg_pcd_ep_wedge(dwc_otg_pcd_t * pcd, void *ep_handle)
-+{
-+ dwc_otg_pcd_ep_t *ep;
-+ dwc_irqflags_t flags;
-+ int retval = 0;
-+
-+ ep = get_ep_from_handle(pcd, ep_handle);
-+
-+ if ((!ep->desc && ep != &pcd->ep0) ||
-+ (ep->desc && (ep->desc->bmAttributes == UE_ISOCHRONOUS))) {
-+ DWC_WARN("%s, bad ep\n", __func__);
-+ return -DWC_E_INVALID;
-+ }
-+
-+ DWC_SPINLOCK_IRQSAVE(pcd->lock, &flags);
-+ if (!DWC_CIRCLEQ_EMPTY(&ep->queue)) {
-+ DWC_WARN("%d %s XFer In process\n", ep->dwc_ep.num,
-+ ep->dwc_ep.is_in ? "IN" : "OUT");
-+ retval = -DWC_E_AGAIN;
-+ } else {
-+ /* This code needs to be reviewed */
-+ if (ep->dwc_ep.is_in == 1 && GET_CORE_IF(pcd)->dma_desc_enable) {
-+ dtxfsts_data_t txstatus;
-+ fifosize_data_t txfifosize;
-+
-+ txfifosize.d32 =
-+ DWC_READ_REG32(&GET_CORE_IF(pcd)->
-+ core_global_regs->dtxfsiz[ep->dwc_ep.
-+ tx_fifo_num]);
-+ txstatus.d32 =
-+ DWC_READ_REG32(&GET_CORE_IF(pcd)->
-+ dev_if->in_ep_regs[ep->dwc_ep.num]->
-+ dtxfsts);
-+
-+ if (txstatus.b.txfspcavail < txfifosize.b.depth) {
-+ DWC_WARN("%s() Data In Tx Fifo\n", __func__);
-+ retval = -DWC_E_AGAIN;
-+ } else {
-+ if (ep->dwc_ep.num == 0) {
-+ pcd->ep0state = EP0_STALL;
-+ }
-+
-+ ep->stopped = 1;
-+ dwc_otg_ep_set_stall(GET_CORE_IF(pcd),
-+ &ep->dwc_ep);
-+ }
-+ } else {
-+ if (ep->dwc_ep.num == 0) {
-+ pcd->ep0state = EP0_STALL;
-+ }
-+
-+ ep->stopped = 1;
-+ dwc_otg_ep_set_stall(GET_CORE_IF(pcd), &ep->dwc_ep);
-+ }
-+ }
-+
-+ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags);
-+
-+ return retval;
-+}
-+
-+int dwc_otg_pcd_ep_halt(dwc_otg_pcd_t * pcd, void *ep_handle, int value)
-+{
-+ dwc_otg_pcd_ep_t *ep;
-+ dwc_irqflags_t flags;
-+ int retval = 0;
-+
-+ ep = get_ep_from_handle(pcd, ep_handle);
-+
-+ if (!ep || (!ep->desc && ep != &pcd->ep0) ||
-+ (ep->desc && (ep->desc->bmAttributes == UE_ISOCHRONOUS))) {
-+ DWC_WARN("%s, bad ep\n", __func__);
-+ return -DWC_E_INVALID;
-+ }
-+
-+ DWC_SPINLOCK_IRQSAVE(pcd->lock, &flags);
-+ if (!DWC_CIRCLEQ_EMPTY(&ep->queue)) {
-+ DWC_WARN("%d %s XFer In process\n", ep->dwc_ep.num,
-+ ep->dwc_ep.is_in ? "IN" : "OUT");
-+ retval = -DWC_E_AGAIN;
-+ } else if (value == 0) {
-+ dwc_otg_ep_clear_stall(GET_CORE_IF(pcd), &ep->dwc_ep);
-+ } else if (value == 1) {
-+ if (ep->dwc_ep.is_in == 1 && GET_CORE_IF(pcd)->dma_desc_enable) {
-+ dtxfsts_data_t txstatus;
-+ fifosize_data_t txfifosize;
-+
-+ txfifosize.d32 =
-+ DWC_READ_REG32(&GET_CORE_IF(pcd)->core_global_regs->
-+ dtxfsiz[ep->dwc_ep.tx_fifo_num]);
-+ txstatus.d32 =
-+ DWC_READ_REG32(&GET_CORE_IF(pcd)->dev_if->
-+ in_ep_regs[ep->dwc_ep.num]->dtxfsts);
-+
-+ if (txstatus.b.txfspcavail < txfifosize.b.depth) {
-+ DWC_WARN("%s() Data In Tx Fifo\n", __func__);
-+ retval = -DWC_E_AGAIN;
-+ } else {
-+ if (ep->dwc_ep.num == 0) {
-+ pcd->ep0state = EP0_STALL;
-+ }
-+
-+ ep->stopped = 1;
-+ dwc_otg_ep_set_stall(GET_CORE_IF(pcd),
-+ &ep->dwc_ep);
-+ }
-+ } else {
-+ if (ep->dwc_ep.num == 0) {
-+ pcd->ep0state = EP0_STALL;
-+ }
-+
-+ ep->stopped = 1;
-+ dwc_otg_ep_set_stall(GET_CORE_IF(pcd), &ep->dwc_ep);
-+ }
-+ } else if (value == 2) {
-+ ep->dwc_ep.stall_clear_flag = 0;
-+ } else if (value == 3) {
-+ ep->dwc_ep.stall_clear_flag = 1;
-+ }
-+
-+ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags);
-+
-+ return retval;
-+}
-+
-+/**
-+ * This function initiates remote wakeup of the host from suspend state.
-+ */
-+void dwc_otg_pcd_rem_wkup_from_suspend(dwc_otg_pcd_t * pcd, int set)
-+{
-+ dctl_data_t dctl = { 0 };
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+ dsts_data_t dsts;
-+
-+ dsts.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dsts);
-+ if (!dsts.b.suspsts) {
-+ DWC_WARN("Remote wakeup while is not in suspend state\n");
-+ }
-+ /* Check if DEVICE_REMOTE_WAKEUP feature enabled */
-+ if (pcd->remote_wakeup_enable) {
-+ if (set) {
-+
-+ if (core_if->adp_enable) {
-+ gpwrdn_data_t gpwrdn;
-+
-+ dwc_otg_adp_probe_stop(core_if);
-+
-+ /* Mask SRP detected interrupt from Power Down Logic */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.srp_det_msk = 1;
-+ DWC_MODIFY_REG32(&core_if->
-+ core_global_regs->gpwrdn,
-+ gpwrdn.d32, 0);
-+
-+ /* Disable Power Down Logic */
-+ gpwrdn.d32 = 0;
-+ gpwrdn.b.pmuactv = 1;
-+ DWC_MODIFY_REG32(&core_if->
-+ core_global_regs->gpwrdn,
-+ gpwrdn.d32, 0);
-+
-+ /*
-+ * Initialize the Core for Device mode.
-+ */
-+ core_if->op_state = B_PERIPHERAL;
-+ dwc_otg_core_init(core_if);
-+ dwc_otg_enable_global_interrupts(core_if);
-+ cil_pcd_start(core_if);
-+
-+ dwc_otg_initiate_srp(core_if);
-+ }
-+
-+ dctl.b.rmtwkupsig = 1;
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->
-+ dctl, 0, dctl.d32);
-+ DWC_DEBUGPL(DBG_PCD, "Set Remote Wakeup\n");
-+
-+ dwc_mdelay(2);
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->
-+ dctl, dctl.d32, 0);
-+ DWC_DEBUGPL(DBG_PCD, "Clear Remote Wakeup\n");
-+ }
-+ } else {
-+ DWC_DEBUGPL(DBG_PCD, "Remote Wakeup is disabled\n");
-+ }
-+}
-+
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+/**
-+ * This function initiates remote wakeup of the host from L1 sleep state.
-+ */
-+void dwc_otg_pcd_rem_wkup_from_sleep(dwc_otg_pcd_t * pcd, int set)
-+{
-+ glpmcfg_data_t lpmcfg;
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+
-+ lpmcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg);
-+
-+ /* Check if we are in L1 state */
-+ if (!lpmcfg.b.prt_sleep_sts) {
-+ DWC_DEBUGPL(DBG_PCD, "Device is not in sleep state\n");
-+ return;
-+ }
-+
-+ /* Check if host allows remote wakeup */
-+ if (!lpmcfg.b.rem_wkup_en) {
-+ DWC_DEBUGPL(DBG_PCD, "Host does not allow remote wakeup\n");
-+ return;
-+ }
-+
-+ /* Check if Resume OK */
-+ if (!lpmcfg.b.sleep_state_resumeok) {
-+ DWC_DEBUGPL(DBG_PCD, "Sleep state resume is not OK\n");
-+ return;
-+ }
-+
-+ lpmcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg);
-+ lpmcfg.b.en_utmi_sleep = 0;
-+ lpmcfg.b.hird_thres &= (~(1 << 4));
-+ DWC_WRITE_REG32(&core_if->core_global_regs->glpmcfg, lpmcfg.d32);
-+
-+ if (set) {
-+ dctl_data_t dctl = {.d32 = 0 };
-+ dctl.b.rmtwkupsig = 1;
-+ /* Set RmtWkUpSig bit to start remote wakup signaling.
-+ * Hardware will automatically clear this bit.
-+ */
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl,
-+ 0, dctl.d32);
-+ DWC_DEBUGPL(DBG_PCD, "Set Remote Wakeup\n");
-+ }
-+
-+}
-+#endif
-+
-+/**
-+ * Performs remote wakeup.
-+ */
-+void dwc_otg_pcd_remote_wakeup(dwc_otg_pcd_t * pcd, int set)
-+{
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+ dwc_irqflags_t flags;
-+ if (dwc_otg_is_device_mode(core_if)) {
-+ DWC_SPINLOCK_IRQSAVE(pcd->lock, &flags);
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+ if (core_if->lx_state == DWC_OTG_L1) {
-+ dwc_otg_pcd_rem_wkup_from_sleep(pcd, set);
-+ } else {
-+#endif
-+ dwc_otg_pcd_rem_wkup_from_suspend(pcd, set);
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+ }
-+#endif
-+ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags);
-+ }
-+ return;
-+}
-+
-+void dwc_otg_pcd_disconnect_us(dwc_otg_pcd_t * pcd, int no_of_usecs)
-+{
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+ dctl_data_t dctl = { 0 };
-+
-+ if (dwc_otg_is_device_mode(core_if)) {
-+ dctl.b.sftdiscon = 1;
-+ DWC_PRINTF("Soft disconnect for %d useconds\n",no_of_usecs);
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl, 0, dctl.d32);
-+ dwc_udelay(no_of_usecs);
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl, dctl.d32,0);
-+
-+ } else{
-+ DWC_PRINTF("NOT SUPPORTED IN HOST MODE\n");
-+ }
-+ return;
-+
-+}
-+
-+int dwc_otg_pcd_wakeup(dwc_otg_pcd_t * pcd)
-+{
-+ dsts_data_t dsts;
-+ gotgctl_data_t gotgctl;
-+
-+ /*
-+ * This function starts the Protocol if no session is in progress. If
-+ * a session is already in progress, but the device is suspended,
-+ * remote wakeup signaling is started.
-+ */
-+
-+ /* Check if valid session */
-+ gotgctl.d32 =
-+ DWC_READ_REG32(&(GET_CORE_IF(pcd)->core_global_regs->gotgctl));
-+ if (gotgctl.b.bsesvld) {
-+ /* Check if suspend state */
-+ dsts.d32 =
-+ DWC_READ_REG32(&
-+ (GET_CORE_IF(pcd)->dev_if->
-+ dev_global_regs->dsts));
-+ if (dsts.b.suspsts) {
-+ dwc_otg_pcd_remote_wakeup(pcd, 1);
-+ }
-+ } else {
-+ dwc_otg_pcd_initiate_srp(pcd);
-+ }
-+
-+ return 0;
-+
-+}
-+
-+/**
-+ * Start the SRP timer to detect when the SRP does not complete within
-+ * 6 seconds.
-+ *
-+ * @param pcd the pcd structure.
-+ */
-+void dwc_otg_pcd_initiate_srp(dwc_otg_pcd_t * pcd)
-+{
-+ dwc_irqflags_t flags;
-+ DWC_SPINLOCK_IRQSAVE(pcd->lock, &flags);
-+ dwc_otg_initiate_srp(GET_CORE_IF(pcd));
-+ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags);
-+}
-+
-+int dwc_otg_pcd_get_frame_number(dwc_otg_pcd_t * pcd)
-+{
-+ return dwc_otg_get_frame_number(GET_CORE_IF(pcd));
-+}
-+
-+int dwc_otg_pcd_is_lpm_enabled(dwc_otg_pcd_t * pcd)
-+{
-+ return GET_CORE_IF(pcd)->core_params->lpm_enable;
-+}
-+
-+uint32_t get_b_hnp_enable(dwc_otg_pcd_t * pcd)
-+{
-+ return pcd->b_hnp_enable;
-+}
-+
-+uint32_t get_a_hnp_support(dwc_otg_pcd_t * pcd)
-+{
-+ return pcd->a_hnp_support;
-+}
-+
-+uint32_t get_a_alt_hnp_support(dwc_otg_pcd_t * pcd)
-+{
-+ return pcd->a_alt_hnp_support;
-+}
-+
-+int dwc_otg_pcd_get_rmwkup_enable(dwc_otg_pcd_t * pcd)
-+{
-+ return pcd->remote_wakeup_enable;
-+}
-+
-+#endif /* DWC_HOST_ONLY */
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_pcd.h
-@@ -0,0 +1,266 @@
-+/* ==========================================================================
-+ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_pcd.h $
-+ * $Revision: #48 $
-+ * $Date: 2012/08/10 $
-+ * $Change: 2047372 $
-+ *
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+#ifndef DWC_HOST_ONLY
-+#if !defined(__DWC_PCD_H__)
-+#define __DWC_PCD_H__
-+
-+#include "dwc_otg_os_dep.h"
-+#include "usb.h"
-+#include "dwc_otg_cil.h"
-+#include "dwc_otg_pcd_if.h"
-+struct cfiobject;
-+
-+/**
-+ * @file
-+ *
-+ * This file contains the structures, constants, and interfaces for
-+ * the Perpherial Contoller Driver (PCD).
-+ *
-+ * The Peripheral Controller Driver (PCD) for Linux will implement the
-+ * Gadget API, so that the existing Gadget drivers can be used. For
-+ * the Mass Storage Function driver the File-backed USB Storage Gadget
-+ * (FBS) driver will be used. The FBS driver supports the
-+ * Control-Bulk (CB), Control-Bulk-Interrupt (CBI), and Bulk-Only
-+ * transports.
-+ *
-+ */
-+
-+/** Invalid DMA Address */
-+#define DWC_DMA_ADDR_INVALID (~(dwc_dma_t)0)
-+
-+/** Max Transfer size for any EP */
-+#define DDMA_MAX_TRANSFER_SIZE 65535
-+
-+/**
-+ * Get the pointer to the core_if from the pcd pointer.
-+ */
-+#define GET_CORE_IF( _pcd ) (_pcd->core_if)
-+
-+/**
-+ * States of EP0.
-+ */
-+typedef enum ep0_state {
-+ EP0_DISCONNECT, /* no host */
-+ EP0_IDLE,
-+ EP0_IN_DATA_PHASE,
-+ EP0_OUT_DATA_PHASE,
-+ EP0_IN_STATUS_PHASE,
-+ EP0_OUT_STATUS_PHASE,
-+ EP0_STALL,
-+} ep0state_e;
-+
-+/** Fordward declaration.*/
-+struct dwc_otg_pcd;
-+
-+/** DWC_otg iso request structure.
-+ *
-+ */
-+typedef struct usb_iso_request dwc_otg_pcd_iso_request_t;
-+
-+#ifdef DWC_UTE_PER_IO
-+
-+/**
-+ * This shall be the exact analogy of the same type structure defined in the
-+ * usb_gadget.h. Each descriptor contains
-+ */
-+struct dwc_iso_pkt_desc_port {
-+ uint32_t offset;
-+ uint32_t length; /* expected length */
-+ uint32_t actual_length;
-+ uint32_t status;
-+};
-+
-+struct dwc_iso_xreq_port {
-+ /** transfer/submission flag */
-+ uint32_t tr_sub_flags;
-+ /** Start the request ASAP */
-+#define DWC_EREQ_TF_ASAP 0x00000002
-+ /** Just enqueue the request w/o initiating a transfer */
-+#define DWC_EREQ_TF_ENQUEUE 0x00000004
-+
-+ /**
-+ * count of ISO packets attached to this request - shall
-+ * not exceed the pio_alloc_pkt_count
-+ */
-+ uint32_t pio_pkt_count;
-+ /** count of ISO packets allocated for this request */
-+ uint32_t pio_alloc_pkt_count;
-+ /** number of ISO packet errors */
-+ uint32_t error_count;
-+ /** reserved for future extension */
-+ uint32_t res;
-+ /** Will be allocated and freed in the UTE gadget and based on the CFC value */
-+ struct dwc_iso_pkt_desc_port *per_io_frame_descs;
-+};
-+#endif
-+/** DWC_otg request structure.
-+ * This structure is a list of requests.
-+ */
-+typedef struct dwc_otg_pcd_request {
-+ void *priv;
-+ void *buf;
-+ dwc_dma_t dma;
-+ uint32_t length;
-+ uint32_t actual;
-+ unsigned sent_zlp:1;
-+ /**
-+ * Used instead of original buffer if
-+ * it(physical address) is not dword-aligned.
-+ **/
-+ uint8_t *dw_align_buf;
-+ dwc_dma_t dw_align_buf_dma;
-+
-+ DWC_CIRCLEQ_ENTRY(dwc_otg_pcd_request) queue_entry;
-+#ifdef DWC_UTE_PER_IO
-+ struct dwc_iso_xreq_port ext_req;
-+ //void *priv_ereq_nport; /* */
-+#endif
-+} dwc_otg_pcd_request_t;
-+
-+DWC_CIRCLEQ_HEAD(req_list, dwc_otg_pcd_request);
-+
-+/** PCD EP structure.
-+ * This structure describes an EP, there is an array of EPs in the PCD
-+ * structure.
-+ */
-+typedef struct dwc_otg_pcd_ep {
-+ /** USB EP Descriptor */
-+ const usb_endpoint_descriptor_t *desc;
-+
-+ /** queue of dwc_otg_pcd_requests. */
-+ struct req_list queue;
-+ unsigned stopped:1;
-+ unsigned disabling:1;
-+ unsigned dma:1;
-+ unsigned queue_sof:1;
-+
-+#ifdef DWC_EN_ISOC
-+ /** ISOC req handle passed */
-+ void *iso_req_handle;
-+#endif //_EN_ISOC_
-+
-+ /** DWC_otg ep data. */
-+ dwc_ep_t dwc_ep;
-+
-+ /** Pointer to PCD */
-+ struct dwc_otg_pcd *pcd;
-+
-+ void *priv;
-+} dwc_otg_pcd_ep_t;
-+
-+/** DWC_otg PCD Structure.
-+ * This structure encapsulates the data for the dwc_otg PCD.
-+ */
-+struct dwc_otg_pcd {
-+ const struct dwc_otg_pcd_function_ops *fops;
-+ /** The DWC otg device pointer */
-+ struct dwc_otg_device *otg_dev;
-+ /** Core Interface */
-+ dwc_otg_core_if_t *core_if;
-+ /** State of EP0 */
-+ ep0state_e ep0state;
-+ /** EP0 Request is pending */
-+ unsigned ep0_pending:1;
-+ /** Indicates when SET CONFIGURATION Request is in process */
-+ unsigned request_config:1;
-+ /** The state of the Remote Wakeup Enable. */
-+ unsigned remote_wakeup_enable:1;
-+ /** The state of the B-Device HNP Enable. */
-+ unsigned b_hnp_enable:1;
-+ /** The state of A-Device HNP Support. */
-+ unsigned a_hnp_support:1;
-+ /** The state of the A-Device Alt HNP support. */
-+ unsigned a_alt_hnp_support:1;
-+ /** Count of pending Requests */
-+ unsigned request_pending;
-+
-+ /** SETUP packet for EP0
-+ * This structure is allocated as a DMA buffer on PCD initialization
-+ * with enough space for up to 3 setup packets.
-+ */
-+ union {
-+ usb_device_request_t req;
-+ uint32_t d32[2];
-+ } *setup_pkt;
-+
-+ dwc_dma_t setup_pkt_dma_handle;
-+
-+ /* Additional buffer and flag for CTRL_WR premature case */
-+ uint8_t *backup_buf;
-+ unsigned data_terminated;
-+
-+ /** 2-byte dma buffer used to return status from GET_STATUS */
-+ uint16_t *status_buf;
-+ dwc_dma_t status_buf_dma_handle;
-+
-+ /** EP0 */
-+ dwc_otg_pcd_ep_t ep0;
-+
-+ /** Array of IN EPs. */
-+ dwc_otg_pcd_ep_t in_ep[MAX_EPS_CHANNELS - 1];
-+ /** Array of OUT EPs. */
-+ dwc_otg_pcd_ep_t out_ep[MAX_EPS_CHANNELS - 1];
-+ /** number of valid EPs in the above array. */
-+// unsigned num_eps : 4;
-+ dwc_spinlock_t *lock;
-+
-+ /** Tasklet to defer starting of TEST mode transmissions until
-+ * Status Phase has been completed.
-+ */
-+ dwc_tasklet_t *test_mode_tasklet;
-+
-+ /** Tasklet to delay starting of xfer in DMA mode */
-+ dwc_tasklet_t *start_xfer_tasklet;
-+
-+ /** The test mode to enter when the tasklet is executed. */
-+ unsigned test_mode;
-+ /** The cfi_api structure that implements most of the CFI API
-+ * and OTG specific core configuration functionality
-+ */
-+#ifdef DWC_UTE_CFI
-+ struct cfiobject *cfi;
-+#endif
-+
-+};
-+
-+//FIXME this functions should be static, and this prototypes should be removed
-+extern void dwc_otg_request_nuke(dwc_otg_pcd_ep_t * ep);
-+extern void dwc_otg_request_done(dwc_otg_pcd_ep_t * ep,
-+ dwc_otg_pcd_request_t * req, int32_t status);
-+
-+void dwc_otg_iso_buffer_done(dwc_otg_pcd_t * pcd, dwc_otg_pcd_ep_t * ep,
-+ void *req_handle);
-+
-+extern void do_test_mode(void *data);
-+#endif
-+#endif /* DWC_HOST_ONLY */
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_pcd_if.h
-@@ -0,0 +1,360 @@
-+/* ==========================================================================
-+ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_pcd_if.h $
-+ * $Revision: #11 $
-+ * $Date: 2011/10/26 $
-+ * $Change: 1873028 $
-+ *
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+#ifndef DWC_HOST_ONLY
-+
-+#if !defined(__DWC_PCD_IF_H__)
-+#define __DWC_PCD_IF_H__
-+
-+//#include "dwc_os.h"
-+#include "dwc_otg_core_if.h"
-+
-+/** @file
-+ * This file defines DWC_OTG PCD Core API.
-+ */
-+
-+struct dwc_otg_pcd;
-+typedef struct dwc_otg_pcd dwc_otg_pcd_t;
-+
-+/** Maxpacket size for EP0 */
-+#define MAX_EP0_SIZE 64
-+/** Maxpacket size for any EP */
-+#define MAX_PACKET_SIZE 1024
-+
-+/** @name Function Driver Callbacks */
-+/** @{ */
-+
-+/** This function will be called whenever a previously queued request has
-+ * completed. The status value will be set to -DWC_E_SHUTDOWN to indicated a
-+ * failed or aborted transfer, or -DWC_E_RESTART to indicate the device was reset,
-+ * or -DWC_E_TIMEOUT to indicate it timed out, or -DWC_E_INVALID to indicate invalid
-+ * parameters. */
-+typedef int (*dwc_completion_cb_t) (dwc_otg_pcd_t * pcd, void *ep_handle,
-+ void *req_handle, int32_t status,
-+ uint32_t actual);
-+/**
-+ * This function will be called whenever a previousle queued ISOC request has
-+ * completed. Count of ISOC packets could be read using dwc_otg_pcd_get_iso_packet_count
-+ * function.
-+ * The status of each ISOC packet could be read using dwc_otg_pcd_get_iso_packet_*
-+ * functions.
-+ */
-+typedef int (*dwc_isoc_completion_cb_t) (dwc_otg_pcd_t * pcd, void *ep_handle,
-+ void *req_handle, int proc_buf_num);
-+/** This function should handle any SETUP request that cannot be handled by the
-+ * PCD Core. This includes most GET_DESCRIPTORs, SET_CONFIGS, Any
-+ * class-specific requests, etc. The function must non-blocking.
-+ *
-+ * Returns 0 on success.
-+ * Returns -DWC_E_NOT_SUPPORTED if the request is not supported.
-+ * Returns -DWC_E_INVALID if the setup request had invalid parameters or bytes.
-+ * Returns -DWC_E_SHUTDOWN on any other error. */
-+typedef int (*dwc_setup_cb_t) (dwc_otg_pcd_t * pcd, uint8_t * bytes);
-+/** This is called whenever the device has been disconnected. The function
-+ * driver should take appropriate action to clean up all pending requests in the
-+ * PCD Core, remove all endpoints (except ep0), and initialize back to reset
-+ * state. */
-+typedef int (*dwc_disconnect_cb_t) (dwc_otg_pcd_t * pcd);
-+/** This function is called when device has been connected. */
-+typedef int (*dwc_connect_cb_t) (dwc_otg_pcd_t * pcd, int speed);
-+/** This function is called when device has been suspended */
-+typedef int (*dwc_suspend_cb_t) (dwc_otg_pcd_t * pcd);
-+/** This function is called when device has received LPM tokens, i.e.
-+ * device has been sent to sleep state. */
-+typedef int (*dwc_sleep_cb_t) (dwc_otg_pcd_t * pcd);
-+/** This function is called when device has been resumed
-+ * from suspend(L2) or L1 sleep state. */
-+typedef int (*dwc_resume_cb_t) (dwc_otg_pcd_t * pcd);
-+/** This function is called whenever hnp params has been changed.
-+ * User can call get_b_hnp_enable, get_a_hnp_support, get_a_alt_hnp_support functions
-+ * to get hnp parameters. */
-+typedef int (*dwc_hnp_params_changed_cb_t) (dwc_otg_pcd_t * pcd);
-+/** This function is called whenever USB RESET is detected. */
-+typedef int (*dwc_reset_cb_t) (dwc_otg_pcd_t * pcd);
-+
-+typedef int (*cfi_setup_cb_t) (dwc_otg_pcd_t * pcd, void *ctrl_req_bytes);
-+
-+/**
-+ *
-+ * @param ep_handle Void pointer to the usb_ep structure
-+ * @param ereq_port Pointer to the extended request structure created in the
-+ * portable part.
-+ */
-+typedef int (*xiso_completion_cb_t) (dwc_otg_pcd_t * pcd, void *ep_handle,
-+ void *req_handle, int32_t status,
-+ void *ereq_port);
-+/** Function Driver Ops Data Structure */
-+struct dwc_otg_pcd_function_ops {
-+ dwc_connect_cb_t connect;
-+ dwc_disconnect_cb_t disconnect;
-+ dwc_setup_cb_t setup;
-+ dwc_completion_cb_t complete;
-+ dwc_isoc_completion_cb_t isoc_complete;
-+ dwc_suspend_cb_t suspend;
-+ dwc_sleep_cb_t sleep;
-+ dwc_resume_cb_t resume;
-+ dwc_reset_cb_t reset;
-+ dwc_hnp_params_changed_cb_t hnp_changed;
-+ cfi_setup_cb_t cfi_setup;
-+#ifdef DWC_UTE_PER_IO
-+ xiso_completion_cb_t xisoc_complete;
-+#endif
-+};
-+/** @} */
-+
-+/** @name Function Driver Functions */
-+/** @{ */
-+
-+/** Call this function to get pointer on dwc_otg_pcd_t,
-+ * this pointer will be used for all PCD API functions.
-+ *
-+ * @param core_if The DWC_OTG Core
-+ */
-+extern dwc_otg_pcd_t *dwc_otg_pcd_init(dwc_otg_core_if_t * core_if);
-+
-+/** Frees PCD allocated by dwc_otg_pcd_init
-+ *
-+ * @param pcd The PCD
-+ */
-+extern void dwc_otg_pcd_remove(dwc_otg_pcd_t * pcd);
-+
-+/** Call this to bind the function driver to the PCD Core.
-+ *
-+ * @param pcd Pointer on dwc_otg_pcd_t returned by dwc_otg_pcd_init function.
-+ * @param fops The Function Driver Ops data structure containing pointers to all callbacks.
-+ */
-+extern void dwc_otg_pcd_start(dwc_otg_pcd_t * pcd,
-+ const struct dwc_otg_pcd_function_ops *fops);
-+
-+/** Enables an endpoint for use. This function enables an endpoint in
-+ * the PCD. The endpoint is described by the ep_desc which has the
-+ * same format as a USB ep descriptor. The ep_handle parameter is used to refer
-+ * to the endpoint from other API functions and in callbacks. Normally this
-+ * should be called after a SET_CONFIGURATION/SET_INTERFACE to configure the
-+ * core for that interface.
-+ *
-+ * Returns -DWC_E_INVALID if invalid parameters were passed.
-+ * Returns -DWC_E_SHUTDOWN if any other error ocurred.
-+ * Returns 0 on success.
-+ *
-+ * @param pcd The PCD
-+ * @param ep_desc Endpoint descriptor
-+ * @param usb_ep Handle on endpoint, that will be used to identify endpoint.
-+ */
-+extern int dwc_otg_pcd_ep_enable(dwc_otg_pcd_t * pcd,
-+ const uint8_t * ep_desc, void *usb_ep);
-+
-+/** Disable the endpoint referenced by ep_handle.
-+ *
-+ * Returns -DWC_E_INVALID if invalid parameters were passed.
-+ * Returns -DWC_E_SHUTDOWN if any other error occurred.
-+ * Returns 0 on success. */
-+extern int dwc_otg_pcd_ep_disable(dwc_otg_pcd_t * pcd, void *ep_handle);
-+
-+/** Queue a data transfer request on the endpoint referenced by ep_handle.
-+ * After the transfer is completes, the complete callback will be called with
-+ * the request status.
-+ *
-+ * @param pcd The PCD
-+ * @param ep_handle The handle of the endpoint
-+ * @param buf The buffer for the data
-+ * @param dma_buf The DMA buffer for the data
-+ * @param buflen The length of the data transfer
-+ * @param zero Specifies whether to send zero length last packet.
-+ * @param req_handle Set this handle to any value to use to reference this
-+ * request in the ep_dequeue function or from the complete callback
-+ * @param atomic_alloc If driver need to perform atomic allocations
-+ * for internal data structures.
-+ *
-+ * Returns -DWC_E_INVALID if invalid parameters were passed.
-+ * Returns -DWC_E_SHUTDOWN if any other error ocurred.
-+ * Returns 0 on success. */
-+extern int dwc_otg_pcd_ep_queue(dwc_otg_pcd_t * pcd, void *ep_handle,
-+ uint8_t * buf, dwc_dma_t dma_buf,
-+ uint32_t buflen, int zero, void *req_handle,
-+ int atomic_alloc);
-+#ifdef DWC_UTE_PER_IO
-+/**
-+ *
-+ * @param ereq_nonport Pointer to the extended request part of the
-+ * usb_request structure defined in usb_gadget.h file.
-+ */
-+extern int dwc_otg_pcd_xiso_ep_queue(dwc_otg_pcd_t * pcd, void *ep_handle,
-+ uint8_t * buf, dwc_dma_t dma_buf,
-+ uint32_t buflen, int zero,
-+ void *req_handle, int atomic_alloc,
-+ void *ereq_nonport);
-+
-+#endif
-+
-+/** De-queue the specified data transfer that has not yet completed.
-+ *
-+ * Returns -DWC_E_INVALID if invalid parameters were passed.
-+ * Returns -DWC_E_SHUTDOWN if any other error ocurred.
-+ * Returns 0 on success. */
-+extern int dwc_otg_pcd_ep_dequeue(dwc_otg_pcd_t * pcd, void *ep_handle,
-+ void *req_handle);
-+
-+/** Halt (STALL) an endpoint or clear it.
-+ *
-+ * Returns -DWC_E_INVALID if invalid parameters were passed.
-+ * Returns -DWC_E_SHUTDOWN if any other error ocurred.
-+ * Returns -DWC_E_AGAIN if the STALL cannot be sent and must be tried again later
-+ * Returns 0 on success. */
-+extern int dwc_otg_pcd_ep_halt(dwc_otg_pcd_t * pcd, void *ep_handle, int value);
-+
-+/** This function */
-+extern int dwc_otg_pcd_ep_wedge(dwc_otg_pcd_t * pcd, void *ep_handle);
-+
-+/** This function should be called on every hardware interrupt */
-+extern int32_t dwc_otg_pcd_handle_intr(dwc_otg_pcd_t * pcd);
-+
-+/** This function returns current frame number */
-+extern int dwc_otg_pcd_get_frame_number(dwc_otg_pcd_t * pcd);
-+
-+/**
-+ * Start isochronous transfers on the endpoint referenced by ep_handle.
-+ * For isochronous transfers duble buffering is used.
-+ * After processing each of buffers comlete callback will be called with
-+ * status for each transaction.
-+ *
-+ * @param pcd The PCD
-+ * @param ep_handle The handle of the endpoint
-+ * @param buf0 The virtual address of first data buffer
-+ * @param buf1 The virtual address of second data buffer
-+ * @param dma0 The DMA address of first data buffer
-+ * @param dma1 The DMA address of second data buffer
-+ * @param sync_frame Data pattern frame number
-+ * @param dp_frame Data size for pattern frame
-+ * @param data_per_frame Data size for regular frame
-+ * @param start_frame Frame number to start transfers, if -1 then start transfers ASAP.
-+ * @param buf_proc_intrvl Interval of ISOC Buffer processing
-+ * @param req_handle Handle of ISOC request
-+ * @param atomic_alloc Specefies whether to perform atomic allocation for
-+ * internal data structures.
-+ *
-+ * Returns -DWC_E_NO_MEMORY if there is no enough memory.
-+ * Returns -DWC_E_INVALID if incorrect arguments are passed to the function.
-+ * Returns -DW_E_SHUTDOWN for any other error.
-+ * Returns 0 on success
-+ */
-+extern int dwc_otg_pcd_iso_ep_start(dwc_otg_pcd_t * pcd, void *ep_handle,
-+ uint8_t * buf0, uint8_t * buf1,
-+ dwc_dma_t dma0, dwc_dma_t dma1,
-+ int sync_frame, int dp_frame,
-+ int data_per_frame, int start_frame,
-+ int buf_proc_intrvl, void *req_handle,
-+ int atomic_alloc);
-+
-+/** Stop ISOC transfers on endpoint referenced by ep_handle.
-+ *
-+ * @param pcd The PCD
-+ * @param ep_handle The handle of the endpoint
-+ * @param req_handle Handle of ISOC request
-+ *
-+ * Returns -DWC_E_INVALID if incorrect arguments are passed to the function
-+ * Returns 0 on success
-+ */
-+int dwc_otg_pcd_iso_ep_stop(dwc_otg_pcd_t * pcd, void *ep_handle,
-+ void *req_handle);
-+
-+/** Get ISOC packet status.
-+ *
-+ * @param pcd The PCD
-+ * @param ep_handle The handle of the endpoint
-+ * @param iso_req_handle Isochronoush request handle
-+ * @param packet Number of packet
-+ * @param status Out parameter for returning status
-+ * @param actual Out parameter for returning actual length
-+ * @param offset Out parameter for returning offset
-+ *
-+ */
-+extern void dwc_otg_pcd_get_iso_packet_params(dwc_otg_pcd_t * pcd,
-+ void *ep_handle,
-+ void *iso_req_handle, int packet,
-+ int *status, int *actual,
-+ int *offset);
-+
-+/** Get ISOC packet count.
-+ *
-+ * @param pcd The PCD
-+ * @param ep_handle The handle of the endpoint
-+ * @param iso_req_handle
-+ */
-+extern int dwc_otg_pcd_get_iso_packet_count(dwc_otg_pcd_t * pcd,
-+ void *ep_handle,
-+ void *iso_req_handle);
-+
-+/** This function starts the SRP Protocol if no session is in progress. If
-+ * a session is already in progress, but the device is suspended,
-+ * remote wakeup signaling is started.
-+ */
-+extern int dwc_otg_pcd_wakeup(dwc_otg_pcd_t * pcd);
-+
-+/** This function returns 1 if LPM support is enabled, and 0 otherwise. */
-+extern int dwc_otg_pcd_is_lpm_enabled(dwc_otg_pcd_t * pcd);
-+
-+/** This function returns 1 if remote wakeup is allowed and 0, otherwise. */
-+extern int dwc_otg_pcd_get_rmwkup_enable(dwc_otg_pcd_t * pcd);
-+
-+/** Initiate SRP */
-+extern void dwc_otg_pcd_initiate_srp(dwc_otg_pcd_t * pcd);
-+
-+/** Starts remote wakeup signaling. */
-+extern void dwc_otg_pcd_remote_wakeup(dwc_otg_pcd_t * pcd, int set);
-+
-+/** Starts micorsecond soft disconnect. */
-+extern void dwc_otg_pcd_disconnect_us(dwc_otg_pcd_t * pcd, int no_of_usecs);
-+/** This function returns whether device is dualspeed.*/
-+extern uint32_t dwc_otg_pcd_is_dualspeed(dwc_otg_pcd_t * pcd);
-+
-+/** This function returns whether device is otg. */
-+extern uint32_t dwc_otg_pcd_is_otg(dwc_otg_pcd_t * pcd);
-+
-+/** These functions allow to get hnp parameters */
-+extern uint32_t get_b_hnp_enable(dwc_otg_pcd_t * pcd);
-+extern uint32_t get_a_hnp_support(dwc_otg_pcd_t * pcd);
-+extern uint32_t get_a_alt_hnp_support(dwc_otg_pcd_t * pcd);
-+
-+/** CFI specific Interface functions */
-+/** Allocate a cfi buffer */
-+extern uint8_t *cfiw_ep_alloc_buffer(dwc_otg_pcd_t * pcd, void *pep,
-+ dwc_dma_t * addr, size_t buflen,
-+ int flags);
-+
-+/******************************************************************************/
-+
-+/** @} */
-+
-+#endif /* __DWC_PCD_IF_H__ */
-+
-+#endif /* DWC_HOST_ONLY */
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_pcd_intr.c
-@@ -0,0 +1,5147 @@
-+/* ==========================================================================
-+ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_pcd_intr.c $
-+ * $Revision: #116 $
-+ * $Date: 2012/08/10 $
-+ * $Change: 2047372 $
-+ *
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+#ifndef DWC_HOST_ONLY
-+
-+#include "dwc_otg_pcd.h"
-+
-+#ifdef DWC_UTE_CFI
-+#include "dwc_otg_cfi.h"
-+#endif
-+
-+#ifdef DWC_UTE_PER_IO
-+extern void complete_xiso_ep(dwc_otg_pcd_ep_t * ep);
-+#endif
-+//#define PRINT_CFI_DMA_DESCS
-+
-+#define DEBUG_EP0
-+
-+/**
-+ * This function updates OTG.
-+ */
-+static void dwc_otg_pcd_update_otg(dwc_otg_pcd_t * pcd, const unsigned reset)
-+{
-+
-+ if (reset) {
-+ pcd->b_hnp_enable = 0;
-+ pcd->a_hnp_support = 0;
-+ pcd->a_alt_hnp_support = 0;
-+ }
-+
-+ if (pcd->fops->hnp_changed) {
-+ pcd->fops->hnp_changed(pcd);
-+ }
-+}
-+
-+/** @file
-+ * This file contains the implementation of the PCD Interrupt handlers.
-+ *
-+ * The PCD handles the device interrupts. Many conditions can cause a
-+ * device interrupt. When an interrupt occurs, the device interrupt
-+ * service routine determines the cause of the interrupt and
-+ * dispatches handling to the appropriate function. These interrupt
-+ * handling functions are described below.
-+ * All interrupt registers are processed from LSB to MSB.
-+ */
-+
-+/**
-+ * This function prints the ep0 state for debug purposes.
-+ */
-+static inline void print_ep0_state(dwc_otg_pcd_t * pcd)
-+{
-+#ifdef DEBUG
-+ char str[40];
-+
-+ switch (pcd->ep0state) {
-+ case EP0_DISCONNECT:
-+ dwc_strcpy(str, "EP0_DISCONNECT");
-+ break;
-+ case EP0_IDLE:
-+ dwc_strcpy(str, "EP0_IDLE");
-+ break;
-+ case EP0_IN_DATA_PHASE:
-+ dwc_strcpy(str, "EP0_IN_DATA_PHASE");
-+ break;
-+ case EP0_OUT_DATA_PHASE:
-+ dwc_strcpy(str, "EP0_OUT_DATA_PHASE");
-+ break;
-+ case EP0_IN_STATUS_PHASE:
-+ dwc_strcpy(str, "EP0_IN_STATUS_PHASE");
-+ break;
-+ case EP0_OUT_STATUS_PHASE:
-+ dwc_strcpy(str, "EP0_OUT_STATUS_PHASE");
-+ break;
-+ case EP0_STALL:
-+ dwc_strcpy(str, "EP0_STALL");
-+ break;
-+ default:
-+ dwc_strcpy(str, "EP0_INVALID");
-+ }
-+
-+ DWC_DEBUGPL(DBG_ANY, "%s(%d)\n", str, pcd->ep0state);
-+#endif
-+}
-+
-+/**
-+ * This function calculate the size of the payload in the memory
-+ * for out endpoints and prints size for debug purposes(used in
-+ * 2.93a DevOutNak feature).
-+ */
-+static inline void print_memory_payload(dwc_otg_pcd_t * pcd, dwc_ep_t * ep)
-+{
-+#ifdef DEBUG
-+ deptsiz_data_t deptsiz_init = {.d32 = 0 };
-+ deptsiz_data_t deptsiz_updt = {.d32 = 0 };
-+ int pack_num;
-+ unsigned payload;
-+
-+ deptsiz_init.d32 = pcd->core_if->start_doeptsiz_val[ep->num];
-+ deptsiz_updt.d32 =
-+ DWC_READ_REG32(&pcd->core_if->dev_if->
-+ out_ep_regs[ep->num]->doeptsiz);
-+ /* Payload will be */
-+ payload = deptsiz_init.b.xfersize - deptsiz_updt.b.xfersize;
-+ /* Packet count is decremented every time a packet
-+ * is written to the RxFIFO not in to the external memory
-+ * So, if payload == 0, then it means no packet was sent to ext memory*/
-+ pack_num = (!payload) ? 0 : (deptsiz_init.b.pktcnt - deptsiz_updt.b.pktcnt);
-+ DWC_DEBUGPL(DBG_PCDV,
-+ "Payload for EP%d-%s\n",
-+ ep->num, (ep->is_in ? "IN" : "OUT"));
-+ DWC_DEBUGPL(DBG_PCDV,
-+ "Number of transfered bytes = 0x%08x\n", payload);
-+ DWC_DEBUGPL(DBG_PCDV,
-+ "Number of transfered packets = %d\n", pack_num);
-+#endif
-+}
-+
-+
-+#ifdef DWC_UTE_CFI
-+static inline void print_desc(struct dwc_otg_dma_desc *ddesc,
-+ const uint8_t * epname, int descnum)
-+{
-+ CFI_INFO
-+ ("%s DMA_DESC(%d) buf=0x%08x bytes=0x%04x; sp=0x%x; l=0x%x; sts=0x%02x; bs=0x%02x\n",
-+ epname, descnum, ddesc->buf, ddesc->status.b.bytes,
-+ ddesc->status.b.sp, ddesc->status.b.l, ddesc->status.b.sts,
-+ ddesc->status.b.bs);
-+}
-+#endif
-+
-+/**
-+ * This function returns pointer to in ep struct with number ep_num
-+ */
-+static inline dwc_otg_pcd_ep_t *get_in_ep(dwc_otg_pcd_t * pcd, uint32_t ep_num)
-+{
-+ int i;
-+ int num_in_eps = GET_CORE_IF(pcd)->dev_if->num_in_eps;
-+ if (ep_num == 0) {
-+ return &pcd->ep0;
-+ } else {
-+ for (i = 0; i < num_in_eps; ++i) {
-+ if (pcd->in_ep[i].dwc_ep.num == ep_num)
-+ return &pcd->in_ep[i];
-+ }
-+ return 0;
-+ }
-+}
-+
-+/**
-+ * This function returns pointer to out ep struct with number ep_num
-+ */
-+static inline dwc_otg_pcd_ep_t *get_out_ep(dwc_otg_pcd_t * pcd, uint32_t ep_num)
-+{
-+ int i;
-+ int num_out_eps = GET_CORE_IF(pcd)->dev_if->num_out_eps;
-+ if (ep_num == 0) {
-+ return &pcd->ep0;
-+ } else {
-+ for (i = 0; i < num_out_eps; ++i) {
-+ if (pcd->out_ep[i].dwc_ep.num == ep_num)
-+ return &pcd->out_ep[i];
-+ }
-+ return 0;
-+ }
-+}
-+
-+/**
-+ * This functions gets a pointer to an EP from the wIndex address
-+ * value of the control request.
-+ */
-+dwc_otg_pcd_ep_t *get_ep_by_addr(dwc_otg_pcd_t * pcd, u16 wIndex)
-+{
-+ dwc_otg_pcd_ep_t *ep;
-+ uint32_t ep_num = UE_GET_ADDR(wIndex);
-+
-+ if (ep_num == 0) {
-+ ep = &pcd->ep0;
-+ } else if (UE_GET_DIR(wIndex) == UE_DIR_IN) { /* in ep */
-+ ep = &pcd->in_ep[ep_num - 1];
-+ } else {
-+ ep = &pcd->out_ep[ep_num - 1];
-+ }
-+
-+ return ep;
-+}
-+
-+/**
-+ * This function checks the EP request queue, if the queue is not
-+ * empty the next request is started.
-+ */
-+void start_next_request(dwc_otg_pcd_ep_t * ep)
-+{
-+ dwc_otg_pcd_request_t *req = 0;
-+ uint32_t max_transfer =
-+ GET_CORE_IF(ep->pcd)->core_params->max_transfer_size;
-+
-+#ifdef DWC_UTE_CFI
-+ struct dwc_otg_pcd *pcd;
-+ pcd = ep->pcd;
-+#endif
-+
-+ if (!DWC_CIRCLEQ_EMPTY(&ep->queue)) {
-+ req = DWC_CIRCLEQ_FIRST(&ep->queue);
-+
-+#ifdef DWC_UTE_CFI
-+ if (ep->dwc_ep.buff_mode != BM_STANDARD) {
-+ ep->dwc_ep.cfi_req_len = req->length;
-+ pcd->cfi->ops.build_descriptors(pcd->cfi, pcd, ep, req);
-+ } else {
-+#endif
-+ /* Setup and start the Transfer */
-+ if (req->dw_align_buf) {
-+ ep->dwc_ep.dma_addr = req->dw_align_buf_dma;
-+ ep->dwc_ep.start_xfer_buff = req->dw_align_buf;
-+ ep->dwc_ep.xfer_buff = req->dw_align_buf;
-+ } else {
-+ ep->dwc_ep.dma_addr = req->dma;
-+ ep->dwc_ep.start_xfer_buff = req->buf;
-+ ep->dwc_ep.xfer_buff = req->buf;
-+ }
-+ ep->dwc_ep.sent_zlp = 0;
-+ ep->dwc_ep.total_len = req->length;
-+ ep->dwc_ep.xfer_len = 0;
-+ ep->dwc_ep.xfer_count = 0;
-+
-+ ep->dwc_ep.maxxfer = max_transfer;
-+ if (GET_CORE_IF(ep->pcd)->dma_desc_enable) {
-+ uint32_t out_max_xfer = DDMA_MAX_TRANSFER_SIZE
-+ - (DDMA_MAX_TRANSFER_SIZE % 4);
-+ if (ep->dwc_ep.is_in) {
-+ if (ep->dwc_ep.maxxfer >
-+ DDMA_MAX_TRANSFER_SIZE) {
-+ ep->dwc_ep.maxxfer =
-+ DDMA_MAX_TRANSFER_SIZE;
-+ }
-+ } else {
-+ if (ep->dwc_ep.maxxfer > out_max_xfer) {
-+ ep->dwc_ep.maxxfer =
-+ out_max_xfer;
-+ }
-+ }
-+ }
-+ if (ep->dwc_ep.maxxfer < ep->dwc_ep.total_len) {
-+ ep->dwc_ep.maxxfer -=
-+ (ep->dwc_ep.maxxfer % ep->dwc_ep.maxpacket);
-+ }
-+ if (req->sent_zlp) {
-+ if ((ep->dwc_ep.total_len %
-+ ep->dwc_ep.maxpacket == 0)
-+ && (ep->dwc_ep.total_len != 0)) {
-+ ep->dwc_ep.sent_zlp = 1;
-+ }
-+
-+ }
-+#ifdef DWC_UTE_CFI
-+ }
-+#endif
-+ dwc_otg_ep_start_transfer(GET_CORE_IF(ep->pcd), &ep->dwc_ep);
-+ } else if (ep->dwc_ep.type == DWC_OTG_EP_TYPE_ISOC) {
-+ DWC_PRINTF("There are no more ISOC requests \n");
-+ ep->dwc_ep.frame_num = 0xFFFFFFFF;
-+ }
-+}
-+
-+/**
-+ * This function handles the SOF Interrupts. At this time the SOF
-+ * Interrupt is disabled.
-+ */
-+int32_t dwc_otg_pcd_handle_sof_intr(dwc_otg_pcd_t * pcd)
-+{
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+
-+ gintsts_data_t gintsts;
-+
-+ DWC_DEBUGPL(DBG_PCD, "SOF\n");
-+
-+ /* Clear interrupt */
-+ gintsts.d32 = 0;
-+ gintsts.b.sofintr = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32);
-+
-+ return 1;
-+}
-+
-+/**
-+ * This function handles the Rx Status Queue Level Interrupt, which
-+ * indicates that there is a least one packet in the Rx FIFO. The
-+ * packets are moved from the FIFO to memory, where they will be
-+ * processed when the Endpoint Interrupt Register indicates Transfer
-+ * Complete or SETUP Phase Done.
-+ *
-+ * Repeat the following until the Rx Status Queue is empty:
-+ * -# Read the Receive Status Pop Register (GRXSTSP) to get Packet
-+ * info
-+ * -# If Receive FIFO is empty then skip to step Clear the interrupt
-+ * and exit
-+ * -# If SETUP Packet call dwc_otg_read_setup_packet to copy the
-+ * SETUP data to the buffer
-+ * -# If OUT Data Packet call dwc_otg_read_packet to copy the data
-+ * to the destination buffer
-+ */
-+int32_t dwc_otg_pcd_handle_rx_status_q_level_intr(dwc_otg_pcd_t * pcd)
-+{
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs;
-+ gintmsk_data_t gintmask = {.d32 = 0 };
-+ device_grxsts_data_t status;
-+ dwc_otg_pcd_ep_t *ep;
-+ gintsts_data_t gintsts;
-+#ifdef DEBUG
-+ static char *dpid_str[] = { "D0", "D2", "D1", "MDATA" };
-+#endif
-+
-+ //DWC_DEBUGPL(DBG_PCDV, "%s(%p)\n", __func__, _pcd);
-+ /* Disable the Rx Status Queue Level interrupt */
-+ gintmask.b.rxstsqlvl = 1;
-+ DWC_MODIFY_REG32(&global_regs->gintmsk, gintmask.d32, 0);
-+
-+ /* Get the Status from the top of the FIFO */
-+ status.d32 = DWC_READ_REG32(&global_regs->grxstsp);
-+
-+ DWC_DEBUGPL(DBG_PCD, "EP:%d BCnt:%d DPID:%s "
-+ "pktsts:%x Frame:%d(0x%0x)\n",
-+ status.b.epnum, status.b.bcnt,
-+ dpid_str[status.b.dpid],
-+ status.b.pktsts, status.b.fn, status.b.fn);
-+ /* Get pointer to EP structure */
-+ ep = get_out_ep(pcd, status.b.epnum);
-+
-+ switch (status.b.pktsts) {
-+ case DWC_DSTS_GOUT_NAK:
-+ DWC_DEBUGPL(DBG_PCDV, "Global OUT NAK\n");
-+ break;
-+ case DWC_STS_DATA_UPDT:
-+ DWC_DEBUGPL(DBG_PCDV, "OUT Data Packet\n");
-+ if (status.b.bcnt && ep->dwc_ep.xfer_buff) {
-+ /** @todo NGS Check for buffer overflow? */
-+ dwc_otg_read_packet(core_if,
-+ ep->dwc_ep.xfer_buff,
-+ status.b.bcnt);
-+ ep->dwc_ep.xfer_count += status.b.bcnt;
-+ ep->dwc_ep.xfer_buff += status.b.bcnt;
-+ }
-+ break;
-+ case DWC_STS_XFER_COMP:
-+ DWC_DEBUGPL(DBG_PCDV, "OUT Complete\n");
-+ break;
-+ case DWC_DSTS_SETUP_COMP:
-+#ifdef DEBUG_EP0
-+ DWC_DEBUGPL(DBG_PCDV, "Setup Complete\n");
-+#endif
-+ break;
-+ case DWC_DSTS_SETUP_UPDT:
-+ dwc_otg_read_setup_packet(core_if, pcd->setup_pkt->d32);
-+#ifdef DEBUG_EP0
-+ DWC_DEBUGPL(DBG_PCD,
-+ "SETUP PKT: %02x.%02x v%04x i%04x l%04x\n",
-+ pcd->setup_pkt->req.bmRequestType,
-+ pcd->setup_pkt->req.bRequest,
-+ UGETW(pcd->setup_pkt->req.wValue),
-+ UGETW(pcd->setup_pkt->req.wIndex),
-+ UGETW(pcd->setup_pkt->req.wLength));
-+#endif
-+ ep->dwc_ep.xfer_count += status.b.bcnt;
-+ break;
-+ default:
-+ DWC_DEBUGPL(DBG_PCDV, "Invalid Packet Status (0x%0x)\n",
-+ status.b.pktsts);
-+ break;
-+ }
-+
-+ /* Enable the Rx Status Queue Level interrupt */
-+ DWC_MODIFY_REG32(&global_regs->gintmsk, 0, gintmask.d32);
-+ /* Clear interrupt */
-+ gintsts.d32 = 0;
-+ gintsts.b.rxstsqlvl = 1;
-+ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32);
-+
-+ //DWC_DEBUGPL(DBG_PCDV, "EXIT: %s\n", __func__);
-+ return 1;
-+}
-+
-+/**
-+ * This function examines the Device IN Token Learning Queue to
-+ * determine the EP number of the last IN token received. This
-+ * implementation is for the Mass Storage device where there are only
-+ * 2 IN EPs (Control-IN and BULK-IN).
-+ *
-+ * The EP numbers for the first six IN Tokens are in DTKNQR1 and there
-+ * are 8 EP Numbers in each of the other possible DTKNQ Registers.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ *
-+ */
-+static inline int get_ep_of_last_in_token(dwc_otg_core_if_t * core_if)
-+{
-+ dwc_otg_device_global_regs_t *dev_global_regs =
-+ core_if->dev_if->dev_global_regs;
-+ const uint32_t TOKEN_Q_DEPTH = core_if->hwcfg2.b.dev_token_q_depth;
-+ /* Number of Token Queue Registers */
-+ const int DTKNQ_REG_CNT = (TOKEN_Q_DEPTH + 7) / 8;
-+ dtknq1_data_t dtknqr1;
-+ uint32_t in_tkn_epnums[4];
-+ int ndx = 0;
-+ int i = 0;
-+ volatile uint32_t *addr = &dev_global_regs->dtknqr1;
-+ int epnum = 0;
-+
-+ //DWC_DEBUGPL(DBG_PCD,"dev_token_q_depth=%d\n",TOKEN_Q_DEPTH);
-+
-+ /* Read the DTKNQ Registers */
-+ for (i = 0; i < DTKNQ_REG_CNT; i++) {
-+ in_tkn_epnums[i] = DWC_READ_REG32(addr);
-+ DWC_DEBUGPL(DBG_PCDV, "DTKNQR%d=0x%08x\n", i + 1,
-+ in_tkn_epnums[i]);
-+ if (addr == &dev_global_regs->dvbusdis) {
-+ addr = &dev_global_regs->dtknqr3_dthrctl;
-+ } else {
-+ ++addr;
-+ }
-+
-+ }
-+
-+ /* Copy the DTKNQR1 data to the bit field. */
-+ dtknqr1.d32 = in_tkn_epnums[0];
-+ /* Get the EP numbers */
-+ in_tkn_epnums[0] = dtknqr1.b.epnums0_5;
-+ ndx = dtknqr1.b.intknwptr - 1;
-+
-+ //DWC_DEBUGPL(DBG_PCDV,"ndx=%d\n",ndx);
-+ if (ndx == -1) {
-+ /** @todo Find a simpler way to calculate the max
-+ * queue position.*/
-+ int cnt = TOKEN_Q_DEPTH;
-+ if (TOKEN_Q_DEPTH <= 6) {
-+ cnt = TOKEN_Q_DEPTH - 1;
-+ } else if (TOKEN_Q_DEPTH <= 14) {
-+ cnt = TOKEN_Q_DEPTH - 7;
-+ } else if (TOKEN_Q_DEPTH <= 22) {
-+ cnt = TOKEN_Q_DEPTH - 15;
-+ } else {
-+ cnt = TOKEN_Q_DEPTH - 23;
-+ }
-+ epnum = (in_tkn_epnums[DTKNQ_REG_CNT - 1] >> (cnt * 4)) & 0xF;
-+ } else {
-+ if (ndx <= 5) {
-+ epnum = (in_tkn_epnums[0] >> (ndx * 4)) & 0xF;
-+ } else if (ndx <= 13) {
-+ ndx -= 6;
-+ epnum = (in_tkn_epnums[1] >> (ndx * 4)) & 0xF;
-+ } else if (ndx <= 21) {
-+ ndx -= 14;
-+ epnum = (in_tkn_epnums[2] >> (ndx * 4)) & 0xF;
-+ } else if (ndx <= 29) {
-+ ndx -= 22;
-+ epnum = (in_tkn_epnums[3] >> (ndx * 4)) & 0xF;
-+ }
-+ }
-+ //DWC_DEBUGPL(DBG_PCD,"epnum=%d\n",epnum);
-+ return epnum;
-+}
-+
-+/**
-+ * This interrupt occurs when the non-periodic Tx FIFO is half-empty.
-+ * The active request is checked for the next packet to be loaded into
-+ * the non-periodic Tx FIFO.
-+ */
-+int32_t dwc_otg_pcd_handle_np_tx_fifo_empty_intr(dwc_otg_pcd_t * pcd)
-+{
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs;
-+ dwc_otg_dev_in_ep_regs_t *ep_regs;
-+ gnptxsts_data_t txstatus = {.d32 = 0 };
-+ gintsts_data_t gintsts;
-+
-+ int epnum = 0;
-+ dwc_otg_pcd_ep_t *ep = 0;
-+ uint32_t len = 0;
-+ int dwords;
-+
-+ /* Get the epnum from the IN Token Learning Queue. */
-+ epnum = get_ep_of_last_in_token(core_if);
-+ ep = get_in_ep(pcd, epnum);
-+
-+ DWC_DEBUGPL(DBG_PCD, "NP TxFifo Empty: %d \n", epnum);
-+
-+ ep_regs = core_if->dev_if->in_ep_regs[epnum];
-+
-+ len = ep->dwc_ep.xfer_len - ep->dwc_ep.xfer_count;
-+ if (len > ep->dwc_ep.maxpacket) {
-+ len = ep->dwc_ep.maxpacket;
-+ }
-+ dwords = (len + 3) / 4;
-+
-+ /* While there is space in the queue and space in the FIFO and
-+ * More data to tranfer, Write packets to the Tx FIFO */
-+ txstatus.d32 = DWC_READ_REG32(&global_regs->gnptxsts);
-+ DWC_DEBUGPL(DBG_PCDV, "b4 GNPTXSTS=0x%08x\n", txstatus.d32);
-+
-+ while (txstatus.b.nptxqspcavail > 0 &&
-+ txstatus.b.nptxfspcavail > dwords &&
-+ ep->dwc_ep.xfer_count < ep->dwc_ep.xfer_len) {
-+ /* Write the FIFO */
-+ dwc_otg_ep_write_packet(core_if, &ep->dwc_ep, 0);
-+ len = ep->dwc_ep.xfer_len - ep->dwc_ep.xfer_count;
-+
-+ if (len > ep->dwc_ep.maxpacket) {
-+ len = ep->dwc_ep.maxpacket;
-+ }
-+
-+ dwords = (len + 3) / 4;
-+ txstatus.d32 = DWC_READ_REG32(&global_regs->gnptxsts);
-+ DWC_DEBUGPL(DBG_PCDV, "GNPTXSTS=0x%08x\n", txstatus.d32);
-+ }
-+
-+ DWC_DEBUGPL(DBG_PCDV, "GNPTXSTS=0x%08x\n",
-+ DWC_READ_REG32(&global_regs->gnptxsts));
-+
-+ /* Clear interrupt */
-+ gintsts.d32 = 0;
-+ gintsts.b.nptxfempty = 1;
-+ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32);
-+
-+ return 1;
-+}
-+
-+/**
-+ * This function is called when dedicated Tx FIFO Empty interrupt occurs.
-+ * The active request is checked for the next packet to be loaded into
-+ * apropriate Tx FIFO.
-+ */
-+static int32_t write_empty_tx_fifo(dwc_otg_pcd_t * pcd, uint32_t epnum)
-+{
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+ dwc_otg_dev_if_t *dev_if = core_if->dev_if;
-+ dwc_otg_dev_in_ep_regs_t *ep_regs;
-+ dtxfsts_data_t txstatus = {.d32 = 0 };
-+ dwc_otg_pcd_ep_t *ep = 0;
-+ uint32_t len = 0;
-+ int dwords;
-+
-+ ep = get_in_ep(pcd, epnum);
-+
-+ DWC_DEBUGPL(DBG_PCD, "Dedicated TxFifo Empty: %d \n", epnum);
-+
-+ ep_regs = core_if->dev_if->in_ep_regs[epnum];
-+
-+ len = ep->dwc_ep.xfer_len - ep->dwc_ep.xfer_count;
-+
-+ if (len > ep->dwc_ep.maxpacket) {
-+ len = ep->dwc_ep.maxpacket;
-+ }
-+
-+ dwords = (len + 3) / 4;
-+
-+ /* While there is space in the queue and space in the FIFO and
-+ * More data to tranfer, Write packets to the Tx FIFO */
-+ txstatus.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[epnum]->dtxfsts);
-+ DWC_DEBUGPL(DBG_PCDV, "b4 dtxfsts[%d]=0x%08x\n", epnum, txstatus.d32);
-+
-+ while (txstatus.b.txfspcavail > dwords &&
-+ ep->dwc_ep.xfer_count < ep->dwc_ep.xfer_len &&
-+ ep->dwc_ep.xfer_len != 0) {
-+ /* Write the FIFO */
-+ dwc_otg_ep_write_packet(core_if, &ep->dwc_ep, 0);
-+
-+ len = ep->dwc_ep.xfer_len - ep->dwc_ep.xfer_count;
-+ if (len > ep->dwc_ep.maxpacket) {
-+ len = ep->dwc_ep.maxpacket;
-+ }
-+
-+ dwords = (len + 3) / 4;
-+ txstatus.d32 =
-+ DWC_READ_REG32(&dev_if->in_ep_regs[epnum]->dtxfsts);
-+ DWC_DEBUGPL(DBG_PCDV, "dtxfsts[%d]=0x%08x\n", epnum,
-+ txstatus.d32);
-+ }
-+
-+ DWC_DEBUGPL(DBG_PCDV, "b4 dtxfsts[%d]=0x%08x\n", epnum,
-+ DWC_READ_REG32(&dev_if->in_ep_regs[epnum]->dtxfsts));
-+
-+ return 1;
-+}
-+
-+/**
-+ * This function is called when the Device is disconnected. It stops
-+ * any active requests and informs the Gadget driver of the
-+ * disconnect.
-+ */
-+void dwc_otg_pcd_stop(dwc_otg_pcd_t * pcd)
-+{
-+ int i, num_in_eps, num_out_eps;
-+ dwc_otg_pcd_ep_t *ep;
-+
-+ gintmsk_data_t intr_mask = {.d32 = 0 };
-+
-+ DWC_SPINLOCK(pcd->lock);
-+
-+ num_in_eps = GET_CORE_IF(pcd)->dev_if->num_in_eps;
-+ num_out_eps = GET_CORE_IF(pcd)->dev_if->num_out_eps;
-+
-+ DWC_DEBUGPL(DBG_PCDV, "%s() \n", __func__);
-+ /* don't disconnect drivers more than once */
-+ if (pcd->ep0state == EP0_DISCONNECT) {
-+ DWC_DEBUGPL(DBG_ANY, "%s() Already Disconnected\n", __func__);
-+ DWC_SPINUNLOCK(pcd->lock);
-+ return;
-+ }
-+ pcd->ep0state = EP0_DISCONNECT;
-+
-+ /* Reset the OTG state. */
-+ dwc_otg_pcd_update_otg(pcd, 1);
-+
-+ /* Disable the NP Tx Fifo Empty Interrupt. */
-+ intr_mask.b.nptxfempty = 1;
-+ DWC_MODIFY_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintmsk,
-+ intr_mask.d32, 0);
-+
-+ /* Flush the FIFOs */
-+ /**@todo NGS Flush Periodic FIFOs */
-+ dwc_otg_flush_tx_fifo(GET_CORE_IF(pcd), 0x10);
-+ dwc_otg_flush_rx_fifo(GET_CORE_IF(pcd));
-+
-+ /* prevent new request submissions, kill any outstanding requests */
-+ ep = &pcd->ep0;
-+ dwc_otg_request_nuke(ep);
-+ /* prevent new request submissions, kill any outstanding requests */
-+ for (i = 0; i < num_in_eps; i++) {
-+ dwc_otg_pcd_ep_t *ep = &pcd->in_ep[i];
-+ dwc_otg_request_nuke(ep);
-+ }
-+ /* prevent new request submissions, kill any outstanding requests */
-+ for (i = 0; i < num_out_eps; i++) {
-+ dwc_otg_pcd_ep_t *ep = &pcd->out_ep[i];
-+ dwc_otg_request_nuke(ep);
-+ }
-+
-+ /* report disconnect; the driver is already quiesced */
-+ if (pcd->fops->disconnect) {
-+ DWC_SPINUNLOCK(pcd->lock);
-+ pcd->fops->disconnect(pcd);
-+ DWC_SPINLOCK(pcd->lock);
-+ }
-+ DWC_SPINUNLOCK(pcd->lock);
-+}
-+
-+/**
-+ * This interrupt indicates that ...
-+ */
-+int32_t dwc_otg_pcd_handle_i2c_intr(dwc_otg_pcd_t * pcd)
-+{
-+ gintmsk_data_t intr_mask = {.d32 = 0 };
-+ gintsts_data_t gintsts;
-+
-+ DWC_PRINTF("INTERRUPT Handler not implemented for %s\n", "i2cintr");
-+ intr_mask.b.i2cintr = 1;
-+ DWC_MODIFY_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintmsk,
-+ intr_mask.d32, 0);
-+
-+ /* Clear interrupt */
-+ gintsts.d32 = 0;
-+ gintsts.b.i2cintr = 1;
-+ DWC_WRITE_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintsts,
-+ gintsts.d32);
-+ return 1;
-+}
-+
-+/**
-+ * This interrupt indicates that ...
-+ */
-+int32_t dwc_otg_pcd_handle_early_suspend_intr(dwc_otg_pcd_t * pcd)
-+{
-+ gintsts_data_t gintsts;
-+#if defined(VERBOSE)
-+ DWC_PRINTF("Early Suspend Detected\n");
-+#endif
-+
-+ /* Clear interrupt */
-+ gintsts.d32 = 0;
-+ gintsts.b.erlysuspend = 1;
-+ DWC_WRITE_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintsts,
-+ gintsts.d32);
-+ return 1;
-+}
-+
-+/**
-+ * This function configures EPO to receive SETUP packets.
-+ *
-+ * @todo NGS: Update the comments from the HW FS.
-+ *
-+ * -# Program the following fields in the endpoint specific registers
-+ * for Control OUT EP 0, in order to receive a setup packet
-+ * - DOEPTSIZ0.Packet Count = 3 (To receive up to 3 back to back
-+ * setup packets)
-+ * - DOEPTSIZE0.Transfer Size = 24 Bytes (To receive up to 3 back
-+ * to back setup packets)
-+ * - In DMA mode, DOEPDMA0 Register with a memory address to
-+ * store any setup packets received
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param pcd Programming view of the PCD.
-+ */
-+static inline void ep0_out_start(dwc_otg_core_if_t * core_if,
-+ dwc_otg_pcd_t * pcd)
-+{
-+ dwc_otg_dev_if_t *dev_if = core_if->dev_if;
-+ deptsiz0_data_t doeptsize0 = {.d32 = 0 };
-+ dwc_otg_dev_dma_desc_t *dma_desc;
-+ depctl_data_t doepctl = {.d32 = 0 };
-+
-+#ifdef VERBOSE
-+ DWC_DEBUGPL(DBG_PCDV, "%s() doepctl0=%0x\n", __func__,
-+ DWC_READ_REG32(&dev_if->out_ep_regs[0]->doepctl));
-+#endif
-+ if (core_if->snpsid >= OTG_CORE_REV_3_00a) {
-+ doepctl.d32 = DWC_READ_REG32(&dev_if->out_ep_regs[0]->doepctl);
-+ if (doepctl.b.epena) {
-+ return;
-+ }
-+ }
-+
-+ doeptsize0.b.supcnt = 3;
-+ doeptsize0.b.pktcnt = 1;
-+ doeptsize0.b.xfersize = 8 * 3;
-+
-+ if (core_if->dma_enable) {
-+ if (!core_if->dma_desc_enable) {
-+ /** put here as for Hermes mode deptisz register should not be written */
-+ DWC_WRITE_REG32(&dev_if->out_ep_regs[0]->doeptsiz,
-+ doeptsize0.d32);
-+
-+ /** @todo dma needs to handle multiple setup packets (up to 3) */
-+ DWC_WRITE_REG32(&dev_if->out_ep_regs[0]->doepdma,
-+ pcd->setup_pkt_dma_handle);
-+ } else {
-+ dev_if->setup_desc_index =
-+ (dev_if->setup_desc_index + 1) & 1;
-+ dma_desc =
-+ dev_if->setup_desc_addr[dev_if->setup_desc_index];
-+
-+ /** DMA Descriptor Setup */
-+ dma_desc->status.b.bs = BS_HOST_BUSY;
-+ if (core_if->snpsid >= OTG_CORE_REV_3_00a) {
-+ dma_desc->status.b.sr = 0;
-+ dma_desc->status.b.mtrf = 0;
-+ }
-+ dma_desc->status.b.l = 1;
-+ dma_desc->status.b.ioc = 1;
-+ dma_desc->status.b.bytes = pcd->ep0.dwc_ep.maxpacket;
-+ dma_desc->buf = pcd->setup_pkt_dma_handle;
-+ dma_desc->status.b.sts = 0;
-+ dma_desc->status.b.bs = BS_HOST_READY;
-+
-+ /** DOEPDMA0 Register write */
-+ DWC_WRITE_REG32(&dev_if->out_ep_regs[0]->doepdma,
-+ dev_if->dma_setup_desc_addr
-+ [dev_if->setup_desc_index]);
-+ }
-+
-+ } else {
-+ /** put here as for Hermes mode deptisz register should not be written */
-+ DWC_WRITE_REG32(&dev_if->out_ep_regs[0]->doeptsiz,
-+ doeptsize0.d32);
-+ }
-+
-+ /** DOEPCTL0 Register write cnak will be set after setup interrupt */
-+ doepctl.d32 = 0;
-+ doepctl.b.epena = 1;
-+ if (core_if->snpsid <= OTG_CORE_REV_2_94a) {
-+ doepctl.b.cnak = 1;
-+ DWC_WRITE_REG32(&dev_if->out_ep_regs[0]->doepctl, doepctl.d32);
-+ } else {
-+ DWC_MODIFY_REG32(&dev_if->out_ep_regs[0]->doepctl, 0, doepctl.d32);
-+ }
-+
-+#ifdef VERBOSE
-+ DWC_DEBUGPL(DBG_PCDV, "doepctl0=%0x\n",
-+ DWC_READ_REG32(&dev_if->out_ep_regs[0]->doepctl));
-+ DWC_DEBUGPL(DBG_PCDV, "diepctl0=%0x\n",
-+ DWC_READ_REG32(&dev_if->in_ep_regs[0]->diepctl));
-+#endif
-+}
-+
-+/**
-+ * This interrupt occurs when a USB Reset is detected. When the USB
-+ * Reset Interrupt occurs the device state is set to DEFAULT and the
-+ * EP0 state is set to IDLE.
-+ * -# Set the NAK bit for all OUT endpoints (DOEPCTLn.SNAK = 1)
-+ * -# Unmask the following interrupt bits
-+ * - DAINTMSK.INEP0 = 1 (Control 0 IN endpoint)
-+ * - DAINTMSK.OUTEP0 = 1 (Control 0 OUT endpoint)
-+ * - DOEPMSK.SETUP = 1
-+ * - DOEPMSK.XferCompl = 1
-+ * - DIEPMSK.XferCompl = 1
-+ * - DIEPMSK.TimeOut = 1
-+ * -# Program the following fields in the endpoint specific registers
-+ * for Control OUT EP 0, in order to receive a setup packet
-+ * - DOEPTSIZ0.Packet Count = 3 (To receive up to 3 back to back
-+ * setup packets)
-+ * - DOEPTSIZE0.Transfer Size = 24 Bytes (To receive up to 3 back
-+ * to back setup packets)
-+ * - In DMA mode, DOEPDMA0 Register with a memory address to
-+ * store any setup packets received
-+ * At this point, all the required initialization, except for enabling
-+ * the control 0 OUT endpoint is done, for receiving SETUP packets.
-+ */
-+int32_t dwc_otg_pcd_handle_usb_reset_intr(dwc_otg_pcd_t * pcd)
-+{
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+ dwc_otg_dev_if_t *dev_if = core_if->dev_if;
-+ depctl_data_t doepctl = {.d32 = 0 };
-+ depctl_data_t diepctl = {.d32 = 0 };
-+ daint_data_t daintmsk = {.d32 = 0 };
-+ doepmsk_data_t doepmsk = {.d32 = 0 };
-+ diepmsk_data_t diepmsk = {.d32 = 0 };
-+ dcfg_data_t dcfg = {.d32 = 0 };
-+ grstctl_t resetctl = {.d32 = 0 };
-+ dctl_data_t dctl = {.d32 = 0 };
-+ int i = 0;
-+ gintsts_data_t gintsts;
-+ pcgcctl_data_t power = {.d32 = 0 };
-+
-+ power.d32 = DWC_READ_REG32(core_if->pcgcctl);
-+ if (power.b.stoppclk) {
-+ power.d32 = 0;
-+ power.b.stoppclk = 1;
-+ DWC_MODIFY_REG32(core_if->pcgcctl, power.d32, 0);
-+
-+ power.b.pwrclmp = 1;
-+ DWC_MODIFY_REG32(core_if->pcgcctl, power.d32, 0);
-+
-+ power.b.rstpdwnmodule = 1;
-+ DWC_MODIFY_REG32(core_if->pcgcctl, power.d32, 0);
-+ }
-+
-+ core_if->lx_state = DWC_OTG_L0;
-+
-+ DWC_PRINTF("USB RESET\n");
-+#ifdef DWC_EN_ISOC
-+ for (i = 1; i < 16; ++i) {
-+ dwc_otg_pcd_ep_t *ep;
-+ dwc_ep_t *dwc_ep;
-+ ep = get_in_ep(pcd, i);
-+ if (ep != 0) {
-+ dwc_ep = &ep->dwc_ep;
-+ dwc_ep->next_frame = 0xffffffff;
-+ }
-+ }
-+#endif /* DWC_EN_ISOC */
-+
-+ /* reset the HNP settings */
-+ dwc_otg_pcd_update_otg(pcd, 1);
-+
-+ /* Clear the Remote Wakeup Signalling */
-+ dctl.b.rmtwkupsig = 1;
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl, dctl.d32, 0);
-+
-+ /* Set NAK for all OUT EPs */
-+ doepctl.b.snak = 1;
-+ for (i = 0; i <= dev_if->num_out_eps; i++) {
-+ DWC_WRITE_REG32(&dev_if->out_ep_regs[i]->doepctl, doepctl.d32);
-+ }
-+
-+ /* Flush the NP Tx FIFO */
-+ dwc_otg_flush_tx_fifo(core_if, 0x10);
-+ /* Flush the Learning Queue */
-+ resetctl.b.intknqflsh = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->grstctl, resetctl.d32);
-+
-+ if (!core_if->core_params->en_multiple_tx_fifo && core_if->dma_enable) {
-+ core_if->start_predict = 0;
-+ for (i = 0; i<= core_if->dev_if->num_in_eps; ++i) {
-+ core_if->nextep_seq[i] = 0xff; // 0xff - EP not active
-+ }
-+ core_if->nextep_seq[0] = 0;
-+ core_if->first_in_nextep_seq = 0;
-+ diepctl.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[0]->diepctl);
-+ diepctl.b.nextep = 0;
-+ DWC_WRITE_REG32(&dev_if->in_ep_regs[0]->diepctl, diepctl.d32);
-+
-+ /* Update IN Endpoint Mismatch Count by active IN NP EP count + 1 */
-+ dcfg.d32 = DWC_READ_REG32(&dev_if->dev_global_regs->dcfg);
-+ dcfg.b.epmscnt = 2;
-+ DWC_WRITE_REG32(&dev_if->dev_global_regs->dcfg, dcfg.d32);
-+
-+ DWC_DEBUGPL(DBG_PCDV,
-+ "%s first_in_nextep_seq= %2d; nextep_seq[]:\n",
-+ __func__, core_if->first_in_nextep_seq);
-+ for (i=0; i <= core_if->dev_if->num_in_eps; i++) {
-+ DWC_DEBUGPL(DBG_PCDV, "%2d\n", core_if->nextep_seq[i]);
-+ }
-+ }
-+
-+ if (core_if->multiproc_int_enable) {
-+ daintmsk.b.inep0 = 1;
-+ daintmsk.b.outep0 = 1;
-+ DWC_WRITE_REG32(&dev_if->dev_global_regs->deachintmsk,
-+ daintmsk.d32);
-+
-+ doepmsk.b.setup = 1;
-+ doepmsk.b.xfercompl = 1;
-+ doepmsk.b.ahberr = 1;
-+ doepmsk.b.epdisabled = 1;
-+
-+ if ((core_if->dma_desc_enable) ||
-+ (core_if->dma_enable
-+ && core_if->snpsid >= OTG_CORE_REV_3_00a)) {
-+ doepmsk.b.stsphsercvd = 1;
-+ }
-+ if (core_if->dma_desc_enable)
-+ doepmsk.b.bna = 1;
-+/*
-+ doepmsk.b.babble = 1;
-+ doepmsk.b.nyet = 1;
-+
-+ if (core_if->dma_enable) {
-+ doepmsk.b.nak = 1;
-+ }
-+*/
-+ DWC_WRITE_REG32(&dev_if->dev_global_regs->doepeachintmsk[0],
-+ doepmsk.d32);
-+
-+ diepmsk.b.xfercompl = 1;
-+ diepmsk.b.timeout = 1;
-+ diepmsk.b.epdisabled = 1;
-+ diepmsk.b.ahberr = 1;
-+ diepmsk.b.intknepmis = 1;
-+ if (!core_if->en_multiple_tx_fifo && core_if->dma_enable)
-+ diepmsk.b.intknepmis = 0;
-+
-+/* if (core_if->dma_desc_enable) {
-+ diepmsk.b.bna = 1;
-+ }
-+*/
-+/*
-+ if (core_if->dma_enable) {
-+ diepmsk.b.nak = 1;
-+ }
-+*/
-+ DWC_WRITE_REG32(&dev_if->dev_global_regs->diepeachintmsk[0],
-+ diepmsk.d32);
-+ } else {
-+ daintmsk.b.inep0 = 1;
-+ daintmsk.b.outep0 = 1;
-+ DWC_WRITE_REG32(&dev_if->dev_global_regs->daintmsk,
-+ daintmsk.d32);
-+
-+ doepmsk.b.setup = 1;
-+ doepmsk.b.xfercompl = 1;
-+ doepmsk.b.ahberr = 1;
-+ doepmsk.b.epdisabled = 1;
-+
-+ if ((core_if->dma_desc_enable) ||
-+ (core_if->dma_enable
-+ && core_if->snpsid >= OTG_CORE_REV_3_00a)) {
-+ doepmsk.b.stsphsercvd = 1;
-+ }
-+ if (core_if->dma_desc_enable)
-+ doepmsk.b.bna = 1;
-+ DWC_WRITE_REG32(&dev_if->dev_global_regs->doepmsk, doepmsk.d32);
-+
-+ diepmsk.b.xfercompl = 1;
-+ diepmsk.b.timeout = 1;
-+ diepmsk.b.epdisabled = 1;
-+ diepmsk.b.ahberr = 1;
-+ if (!core_if->en_multiple_tx_fifo && core_if->dma_enable)
-+ diepmsk.b.intknepmis = 0;
-+/*
-+ if (core_if->dma_desc_enable) {
-+ diepmsk.b.bna = 1;
-+ }
-+*/
-+
-+ DWC_WRITE_REG32(&dev_if->dev_global_regs->diepmsk, diepmsk.d32);
-+ }
-+
-+ /* Reset Device Address */
-+ dcfg.d32 = DWC_READ_REG32(&dev_if->dev_global_regs->dcfg);
-+ dcfg.b.devaddr = 0;
-+ DWC_WRITE_REG32(&dev_if->dev_global_regs->dcfg, dcfg.d32);
-+
-+ /* setup EP0 to receive SETUP packets */
-+ if (core_if->snpsid <= OTG_CORE_REV_2_94a)
-+ ep0_out_start(core_if, pcd);
-+
-+ /* Clear interrupt */
-+ gintsts.d32 = 0;
-+ gintsts.b.usbreset = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32);
-+
-+ return 1;
-+}
-+
-+/**
-+ * Get the device speed from the device status register and convert it
-+ * to USB speed constant.
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ */
-+static int get_device_speed(dwc_otg_core_if_t * core_if)
-+{
-+ dsts_data_t dsts;
-+ int speed = 0;
-+ dsts.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dsts);
-+
-+ switch (dsts.b.enumspd) {
-+ case DWC_DSTS_ENUMSPD_HS_PHY_30MHZ_OR_60MHZ:
-+ speed = USB_SPEED_HIGH;
-+ break;
-+ case DWC_DSTS_ENUMSPD_FS_PHY_30MHZ_OR_60MHZ:
-+ case DWC_DSTS_ENUMSPD_FS_PHY_48MHZ:
-+ speed = USB_SPEED_FULL;
-+ break;
-+
-+ case DWC_DSTS_ENUMSPD_LS_PHY_6MHZ:
-+ speed = USB_SPEED_LOW;
-+ break;
-+ }
-+
-+ return speed;
-+}
-+
-+/**
-+ * Read the device status register and set the device speed in the
-+ * data structure.
-+ * Set up EP0 to receive SETUP packets by calling dwc_ep0_activate.
-+ */
-+int32_t dwc_otg_pcd_handle_enum_done_intr(dwc_otg_pcd_t * pcd)
-+{
-+ dwc_otg_pcd_ep_t *ep0 = &pcd->ep0;
-+ gintsts_data_t gintsts;
-+ gusbcfg_data_t gusbcfg;
-+ dwc_otg_core_global_regs_t *global_regs =
-+ GET_CORE_IF(pcd)->core_global_regs;
-+ uint8_t utmi16b, utmi8b;
-+ int speed;
-+ DWC_DEBUGPL(DBG_PCD, "SPEED ENUM\n");
-+
-+ if (GET_CORE_IF(pcd)->snpsid >= OTG_CORE_REV_2_60a) {
-+ utmi16b = 6; //vahrama old value was 6;
-+ utmi8b = 9;
-+ } else {
-+ utmi16b = 4;
-+ utmi8b = 8;
-+ }
-+ dwc_otg_ep0_activate(GET_CORE_IF(pcd), &ep0->dwc_ep);
-+ if (GET_CORE_IF(pcd)->snpsid >= OTG_CORE_REV_3_00a) {
-+ ep0_out_start(GET_CORE_IF(pcd), pcd);
-+ }
-+
-+#ifdef DEBUG_EP0
-+ print_ep0_state(pcd);
-+#endif
-+
-+ if (pcd->ep0state == EP0_DISCONNECT) {
-+ pcd->ep0state = EP0_IDLE;
-+ } else if (pcd->ep0state == EP0_STALL) {
-+ pcd->ep0state = EP0_IDLE;
-+ }
-+
-+ pcd->ep0state = EP0_IDLE;
-+
-+ ep0->stopped = 0;
-+
-+ speed = get_device_speed(GET_CORE_IF(pcd));
-+ pcd->fops->connect(pcd, speed);
-+
-+ /* Set USB turnaround time based on device speed and PHY interface. */
-+ gusbcfg.d32 = DWC_READ_REG32(&global_regs->gusbcfg);
-+ if (speed == USB_SPEED_HIGH) {
-+ if (GET_CORE_IF(pcd)->hwcfg2.b.hs_phy_type ==
-+ DWC_HWCFG2_HS_PHY_TYPE_ULPI) {
-+ /* ULPI interface */
-+ gusbcfg.b.usbtrdtim = 9;
-+ }
-+ if (GET_CORE_IF(pcd)->hwcfg2.b.hs_phy_type ==
-+ DWC_HWCFG2_HS_PHY_TYPE_UTMI) {
-+ /* UTMI+ interface */
-+ if (GET_CORE_IF(pcd)->hwcfg4.b.utmi_phy_data_width == 0) {
-+ gusbcfg.b.usbtrdtim = utmi8b;
-+ } else if (GET_CORE_IF(pcd)->hwcfg4.
-+ b.utmi_phy_data_width == 1) {
-+ gusbcfg.b.usbtrdtim = utmi16b;
-+ } else if (GET_CORE_IF(pcd)->
-+ core_params->phy_utmi_width == 8) {
-+ gusbcfg.b.usbtrdtim = utmi8b;
-+ } else {
-+ gusbcfg.b.usbtrdtim = utmi16b;
-+ }
-+ }
-+ if (GET_CORE_IF(pcd)->hwcfg2.b.hs_phy_type ==
-+ DWC_HWCFG2_HS_PHY_TYPE_UTMI_ULPI) {
-+ /* UTMI+ OR ULPI interface */
-+ if (gusbcfg.b.ulpi_utmi_sel == 1) {
-+ /* ULPI interface */
-+ gusbcfg.b.usbtrdtim = 9;
-+ } else {
-+ /* UTMI+ interface */
-+ if (GET_CORE_IF(pcd)->
-+ core_params->phy_utmi_width == 16) {
-+ gusbcfg.b.usbtrdtim = utmi16b;
-+ } else {
-+ gusbcfg.b.usbtrdtim = utmi8b;
-+ }
-+ }
-+ }
-+ } else {
-+ /* Full or low speed */
-+ gusbcfg.b.usbtrdtim = 9;
-+ }
-+ DWC_WRITE_REG32(&global_regs->gusbcfg, gusbcfg.d32);
-+
-+ /* Clear interrupt */
-+ gintsts.d32 = 0;
-+ gintsts.b.enumdone = 1;
-+ DWC_WRITE_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintsts,
-+ gintsts.d32);
-+ return 1;
-+}
-+
-+/**
-+ * This interrupt indicates that the ISO OUT Packet was dropped due to
-+ * Rx FIFO full or Rx Status Queue Full. If this interrupt occurs
-+ * read all the data from the Rx FIFO.
-+ */
-+int32_t dwc_otg_pcd_handle_isoc_out_packet_dropped_intr(dwc_otg_pcd_t * pcd)
-+{
-+ gintmsk_data_t intr_mask = {.d32 = 0 };
-+ gintsts_data_t gintsts;
-+
-+ DWC_WARN("INTERRUPT Handler not implemented for %s\n",
-+ "ISOC Out Dropped");
-+
-+ intr_mask.b.isooutdrop = 1;
-+ DWC_MODIFY_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintmsk,
-+ intr_mask.d32, 0);
-+
-+ /* Clear interrupt */
-+ gintsts.d32 = 0;
-+ gintsts.b.isooutdrop = 1;
-+ DWC_WRITE_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintsts,
-+ gintsts.d32);
-+
-+ return 1;
-+}
-+
-+/**
-+ * This interrupt indicates the end of the portion of the micro-frame
-+ * for periodic transactions. If there is a periodic transaction for
-+ * the next frame, load the packets into the EP periodic Tx FIFO.
-+ */
-+int32_t dwc_otg_pcd_handle_end_periodic_frame_intr(dwc_otg_pcd_t * pcd)
-+{
-+ gintmsk_data_t intr_mask = {.d32 = 0 };
-+ gintsts_data_t gintsts;
-+ DWC_PRINTF("INTERRUPT Handler not implemented for %s\n", "EOP");
-+
-+ intr_mask.b.eopframe = 1;
-+ DWC_MODIFY_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintmsk,
-+ intr_mask.d32, 0);
-+
-+ /* Clear interrupt */
-+ gintsts.d32 = 0;
-+ gintsts.b.eopframe = 1;
-+ DWC_WRITE_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintsts,
-+ gintsts.d32);
-+
-+ return 1;
-+}
-+
-+/**
-+ * This interrupt indicates that EP of the packet on the top of the
-+ * non-periodic Tx FIFO does not match EP of the IN Token received.
-+ *
-+ * The "Device IN Token Queue" Registers are read to determine the
-+ * order the IN Tokens have been received. The non-periodic Tx FIFO
-+ * is flushed, so it can be reloaded in the order seen in the IN Token
-+ * Queue.
-+ */
-+int32_t dwc_otg_pcd_handle_ep_mismatch_intr(dwc_otg_pcd_t * pcd)
-+{
-+ gintsts_data_t gintsts;
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+ dctl_data_t dctl;
-+ gintmsk_data_t intr_mask = {.d32 = 0 };
-+
-+ if (!core_if->en_multiple_tx_fifo && core_if->dma_enable) {
-+ core_if->start_predict = 1;
-+
-+ DWC_DEBUGPL(DBG_PCDV, "%s(%p)\n", __func__, core_if);
-+
-+ gintsts.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintsts);
-+ if (!gintsts.b.ginnakeff) {
-+ /* Disable EP Mismatch interrupt */
-+ intr_mask.d32 = 0;
-+ intr_mask.b.epmismatch = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gintmsk, intr_mask.d32, 0);
-+ /* Enable the Global IN NAK Effective Interrupt */
-+ intr_mask.d32 = 0;
-+ intr_mask.b.ginnakeff = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gintmsk, 0, intr_mask.d32);
-+ /* Set the global non-periodic IN NAK handshake */
-+ dctl.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dctl);
-+ dctl.b.sgnpinnak = 1;
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dctl, dctl.d32);
-+ } else {
-+ DWC_PRINTF("gintsts.b.ginnakeff = 1! dctl.b.sgnpinnak not set\n");
-+ }
-+ /* Disabling of all EP's will be done in dwc_otg_pcd_handle_in_nak_effective()
-+ * handler after Global IN NAK Effective interrupt will be asserted */
-+ }
-+ /* Clear interrupt */
-+ gintsts.d32 = 0;
-+ gintsts.b.epmismatch = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32);
-+
-+ return 1;
-+}
-+
-+/**
-+ * This interrupt is valid only in DMA mode. This interrupt indicates that the
-+ * core has stopped fetching data for IN endpoints due to the unavailability of
-+ * TxFIFO space or Request Queue space. This interrupt is used by the
-+ * application for an endpoint mismatch algorithm.
-+ *
-+ * @param pcd The PCD
-+ */
-+int32_t dwc_otg_pcd_handle_ep_fetsusp_intr(dwc_otg_pcd_t * pcd)
-+{
-+ gintsts_data_t gintsts;
-+ gintmsk_data_t gintmsk_data;
-+ dctl_data_t dctl;
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+ DWC_DEBUGPL(DBG_PCDV, "%s(%p)\n", __func__, core_if);
-+
-+ /* Clear the global non-periodic IN NAK handshake */
-+ dctl.d32 = 0;
-+ dctl.b.cgnpinnak = 1;
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl, dctl.d32, dctl.d32);
-+
-+ /* Mask GINTSTS.FETSUSP interrupt */
-+ gintmsk_data.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintmsk);
-+ gintmsk_data.b.fetsusp = 0;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintmsk, gintmsk_data.d32);
-+
-+ /* Clear interrupt */
-+ gintsts.d32 = 0;
-+ gintsts.b.fetsusp = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32);
-+
-+ return 1;
-+}
-+/**
-+ * This funcion stalls EP0.
-+ */
-+static inline void ep0_do_stall(dwc_otg_pcd_t * pcd, const int err_val)
-+{
-+ dwc_otg_pcd_ep_t *ep0 = &pcd->ep0;
-+ usb_device_request_t *ctrl = &pcd->setup_pkt->req;
-+ DWC_WARN("req %02x.%02x protocol STALL; err %d\n",
-+ ctrl->bmRequestType, ctrl->bRequest, err_val);
-+
-+ ep0->dwc_ep.is_in = 1;
-+ dwc_otg_ep_set_stall(GET_CORE_IF(pcd), &ep0->dwc_ep);
-+ pcd->ep0.stopped = 1;
-+ pcd->ep0state = EP0_IDLE;
-+ ep0_out_start(GET_CORE_IF(pcd), pcd);
-+}
-+
-+/**
-+ * This functions delegates the setup command to the gadget driver.
-+ */
-+static inline void do_gadget_setup(dwc_otg_pcd_t * pcd,
-+ usb_device_request_t * ctrl)
-+{
-+ int ret = 0;
-+ DWC_SPINUNLOCK(pcd->lock);
-+ ret = pcd->fops->setup(pcd, (uint8_t *) ctrl);
-+ DWC_SPINLOCK(pcd->lock);
-+ if (ret < 0) {
-+ ep0_do_stall(pcd, ret);
-+ }
-+
-+ /** @todo This is a g_file_storage gadget driver specific
-+ * workaround: a DELAYED_STATUS result from the fsg_setup
-+ * routine will result in the gadget queueing a EP0 IN status
-+ * phase for a two-stage control transfer. Exactly the same as
-+ * a SET_CONFIGURATION/SET_INTERFACE except that this is a class
-+ * specific request. Need a generic way to know when the gadget
-+ * driver will queue the status phase. Can we assume when we
-+ * call the gadget driver setup() function that it will always
-+ * queue and require the following flag? Need to look into
-+ * this.
-+ */
-+
-+ if (ret == 256 + 999) {
-+ pcd->request_config = 1;
-+ }
-+}
-+
-+#ifdef DWC_UTE_CFI
-+/**
-+ * This functions delegates the CFI setup commands to the gadget driver.
-+ * This function will return a negative value to indicate a failure.
-+ */
-+static inline int cfi_gadget_setup(dwc_otg_pcd_t * pcd,
-+ struct cfi_usb_ctrlrequest *ctrl_req)
-+{
-+ int ret = 0;
-+
-+ if (pcd->fops && pcd->fops->cfi_setup) {
-+ DWC_SPINUNLOCK(pcd->lock);
-+ ret = pcd->fops->cfi_setup(pcd, ctrl_req);
-+ DWC_SPINLOCK(pcd->lock);
-+ if (ret < 0) {
-+ ep0_do_stall(pcd, ret);
-+ return ret;
-+ }
-+ }
-+
-+ return ret;
-+}
-+#endif
-+
-+/**
-+ * This function starts the Zero-Length Packet for the IN status phase
-+ * of a 2 stage control transfer.
-+ */
-+static inline void do_setup_in_status_phase(dwc_otg_pcd_t * pcd)
-+{
-+ dwc_otg_pcd_ep_t *ep0 = &pcd->ep0;
-+ if (pcd->ep0state == EP0_STALL) {
-+ return;
-+ }
-+
-+ pcd->ep0state = EP0_IN_STATUS_PHASE;
-+
-+ /* Prepare for more SETUP Packets */
-+ DWC_DEBUGPL(DBG_PCD, "EP0 IN ZLP\n");
-+ if ((GET_CORE_IF(pcd)->snpsid >= OTG_CORE_REV_3_00a)
-+ && (pcd->core_if->dma_desc_enable)
-+ && (ep0->dwc_ep.xfer_count < ep0->dwc_ep.total_len)) {
-+ DWC_DEBUGPL(DBG_PCDV,
-+ "Data terminated wait next packet in out_desc_addr\n");
-+ pcd->backup_buf = phys_to_virt(ep0->dwc_ep.dma_addr);
-+ pcd->data_terminated = 1;
-+ }
-+ ep0->dwc_ep.xfer_len = 0;
-+ ep0->dwc_ep.xfer_count = 0;
-+ ep0->dwc_ep.is_in = 1;
-+ ep0->dwc_ep.dma_addr = pcd->setup_pkt_dma_handle;
-+ dwc_otg_ep0_start_transfer(GET_CORE_IF(pcd), &ep0->dwc_ep);
-+
-+ /* Prepare for more SETUP Packets */
-+ //ep0_out_start(GET_CORE_IF(pcd), pcd);
-+}
-+
-+/**
-+ * This function starts the Zero-Length Packet for the OUT status phase
-+ * of a 2 stage control transfer.
-+ */
-+static inline void do_setup_out_status_phase(dwc_otg_pcd_t * pcd)
-+{
-+ dwc_otg_pcd_ep_t *ep0 = &pcd->ep0;
-+ if (pcd->ep0state == EP0_STALL) {
-+ DWC_DEBUGPL(DBG_PCD, "EP0 STALLED\n");
-+ return;
-+ }
-+ pcd->ep0state = EP0_OUT_STATUS_PHASE;
-+
-+ DWC_DEBUGPL(DBG_PCD, "EP0 OUT ZLP\n");
-+ ep0->dwc_ep.xfer_len = 0;
-+ ep0->dwc_ep.xfer_count = 0;
-+ ep0->dwc_ep.is_in = 0;
-+ ep0->dwc_ep.dma_addr = pcd->setup_pkt_dma_handle;
-+ dwc_otg_ep0_start_transfer(GET_CORE_IF(pcd), &ep0->dwc_ep);
-+
-+ /* Prepare for more SETUP Packets */
-+ if (GET_CORE_IF(pcd)->dma_enable == 0) {
-+ ep0_out_start(GET_CORE_IF(pcd), pcd);
-+ }
-+}
-+
-+/**
-+ * Clear the EP halt (STALL) and if pending requests start the
-+ * transfer.
-+ */
-+static inline void pcd_clear_halt(dwc_otg_pcd_t * pcd, dwc_otg_pcd_ep_t * ep)
-+{
-+ if (ep->dwc_ep.stall_clear_flag == 0)
-+ dwc_otg_ep_clear_stall(GET_CORE_IF(pcd), &ep->dwc_ep);
-+
-+ /* Reactive the EP */
-+ dwc_otg_ep_activate(GET_CORE_IF(pcd), &ep->dwc_ep);
-+ if (ep->stopped) {
-+ ep->stopped = 0;
-+ /* If there is a request in the EP queue start it */
-+
-+ /** @todo FIXME: this causes an EP mismatch in DMA mode.
-+ * epmismatch not yet implemented. */
-+
-+ /*
-+ * Above fixme is solved by implmenting a tasklet to call the
-+ * start_next_request(), outside of interrupt context at some
-+ * time after the current time, after a clear-halt setup packet.
-+ * Still need to implement ep mismatch in the future if a gadget
-+ * ever uses more than one endpoint at once
-+ */
-+ ep->queue_sof = 1;
-+ DWC_TASK_SCHEDULE(pcd->start_xfer_tasklet);
-+ }
-+ /* Start Control Status Phase */
-+ do_setup_in_status_phase(pcd);
-+}
-+
-+/**
-+ * This function is called when the SET_FEATURE TEST_MODE Setup packet
-+ * is sent from the host. The Device Control register is written with
-+ * the Test Mode bits set to the specified Test Mode. This is done as
-+ * a tasklet so that the "Status" phase of the control transfer
-+ * completes before transmitting the TEST packets.
-+ *
-+ * @todo This has not been tested since the tasklet struct was put
-+ * into the PCD struct!
-+ *
-+ */
-+void do_test_mode(void *data)
-+{
-+ dctl_data_t dctl;
-+ dwc_otg_pcd_t *pcd = (dwc_otg_pcd_t *) data;
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+ int test_mode = pcd->test_mode;
-+
-+// DWC_WARN("%s() has not been tested since being rewritten!\n", __func__);
-+
-+ dctl.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dctl);
-+ switch (test_mode) {
-+ case 1: // TEST_J
-+ dctl.b.tstctl = 1;
-+ break;
-+
-+ case 2: // TEST_K
-+ dctl.b.tstctl = 2;
-+ break;
-+
-+ case 3: // TEST_SE0_NAK
-+ dctl.b.tstctl = 3;
-+ break;
-+
-+ case 4: // TEST_PACKET
-+ dctl.b.tstctl = 4;
-+ break;
-+
-+ case 5: // TEST_FORCE_ENABLE
-+ dctl.b.tstctl = 5;
-+ break;
-+ }
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dctl, dctl.d32);
-+}
-+
-+/**
-+ * This function process the GET_STATUS Setup Commands.
-+ */
-+static inline void do_get_status(dwc_otg_pcd_t * pcd)
-+{
-+ usb_device_request_t ctrl = pcd->setup_pkt->req;
-+ dwc_otg_pcd_ep_t *ep;
-+ dwc_otg_pcd_ep_t *ep0 = &pcd->ep0;
-+ uint16_t *status = pcd->status_buf;
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+
-+#ifdef DEBUG_EP0
-+ DWC_DEBUGPL(DBG_PCD,
-+ "GET_STATUS %02x.%02x v%04x i%04x l%04x\n",
-+ ctrl.bmRequestType, ctrl.bRequest,
-+ UGETW(ctrl.wValue), UGETW(ctrl.wIndex),
-+ UGETW(ctrl.wLength));
-+#endif
-+
-+ switch (UT_GET_RECIPIENT(ctrl.bmRequestType)) {
-+ case UT_DEVICE:
-+ if(UGETW(ctrl.wIndex) == 0xF000) { /* OTG Status selector */
-+ DWC_PRINTF("wIndex - %d\n", UGETW(ctrl.wIndex));
-+ DWC_PRINTF("OTG VERSION - %d\n", core_if->otg_ver);
-+ DWC_PRINTF("OTG CAP - %d, %d\n",
-+ core_if->core_params->otg_cap,
-+ DWC_OTG_CAP_PARAM_HNP_SRP_CAPABLE);
-+ if (core_if->otg_ver == 1
-+ && core_if->core_params->otg_cap ==
-+ DWC_OTG_CAP_PARAM_HNP_SRP_CAPABLE) {
-+ uint8_t *otgsts = (uint8_t*)pcd->status_buf;
-+ *otgsts = (core_if->otg_sts & 0x1);
-+ pcd->ep0_pending = 1;
-+ ep0->dwc_ep.start_xfer_buff =
-+ (uint8_t *) otgsts;
-+ ep0->dwc_ep.xfer_buff = (uint8_t *) otgsts;
-+ ep0->dwc_ep.dma_addr =
-+ pcd->status_buf_dma_handle;
-+ ep0->dwc_ep.xfer_len = 1;
-+ ep0->dwc_ep.xfer_count = 0;
-+ ep0->dwc_ep.total_len = ep0->dwc_ep.xfer_len;
-+ dwc_otg_ep0_start_transfer(GET_CORE_IF(pcd),
-+ &ep0->dwc_ep);
-+ return;
-+ } else {
-+ ep0_do_stall(pcd, -DWC_E_NOT_SUPPORTED);
-+ return;
-+ }
-+ break;
-+ } else {
-+ *status = 0x1; /* Self powered */
-+ *status |= pcd->remote_wakeup_enable << 1;
-+ break;
-+ }
-+ case UT_INTERFACE:
-+ *status = 0;
-+ break;
-+
-+ case UT_ENDPOINT:
-+ ep = get_ep_by_addr(pcd, UGETW(ctrl.wIndex));
-+ if (ep == 0 || UGETW(ctrl.wLength) > 2) {
-+ ep0_do_stall(pcd, -DWC_E_NOT_SUPPORTED);
-+ return;
-+ }
-+ /** @todo check for EP stall */
-+ *status = ep->stopped;
-+ break;
-+ }
-+ pcd->ep0_pending = 1;
-+ ep0->dwc_ep.start_xfer_buff = (uint8_t *) status;
-+ ep0->dwc_ep.xfer_buff = (uint8_t *) status;
-+ ep0->dwc_ep.dma_addr = pcd->status_buf_dma_handle;
-+ ep0->dwc_ep.xfer_len = 2;
-+ ep0->dwc_ep.xfer_count = 0;
-+ ep0->dwc_ep.total_len = ep0->dwc_ep.xfer_len;
-+ dwc_otg_ep0_start_transfer(GET_CORE_IF(pcd), &ep0->dwc_ep);
-+}
-+
-+/**
-+ * This function process the SET_FEATURE Setup Commands.
-+ */
-+static inline void do_set_feature(dwc_otg_pcd_t * pcd)
-+{
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs;
-+ usb_device_request_t ctrl = pcd->setup_pkt->req;
-+ dwc_otg_pcd_ep_t *ep = 0;
-+ int32_t otg_cap_param = core_if->core_params->otg_cap;
-+ gotgctl_data_t gotgctl = {.d32 = 0 };
-+
-+ DWC_DEBUGPL(DBG_PCD, "SET_FEATURE:%02x.%02x v%04x i%04x l%04x\n",
-+ ctrl.bmRequestType, ctrl.bRequest,
-+ UGETW(ctrl.wValue), UGETW(ctrl.wIndex),
-+ UGETW(ctrl.wLength));
-+ DWC_DEBUGPL(DBG_PCD, "otg_cap=%d\n", otg_cap_param);
-+
-+ switch (UT_GET_RECIPIENT(ctrl.bmRequestType)) {
-+ case UT_DEVICE:
-+ switch (UGETW(ctrl.wValue)) {
-+ case UF_DEVICE_REMOTE_WAKEUP:
-+ pcd->remote_wakeup_enable = 1;
-+ break;
-+
-+ case UF_TEST_MODE:
-+ /* Setup the Test Mode tasklet to do the Test
-+ * Packet generation after the SETUP Status
-+ * phase has completed. */
-+
-+ /** @todo This has not been tested since the
-+ * tasklet struct was put into the PCD
-+ * struct! */
-+ pcd->test_mode = UGETW(ctrl.wIndex) >> 8;
-+ DWC_TASK_SCHEDULE(pcd->test_mode_tasklet);
-+ break;
-+
-+ case UF_DEVICE_B_HNP_ENABLE:
-+ DWC_DEBUGPL(DBG_PCDV,
-+ "SET_FEATURE: USB_DEVICE_B_HNP_ENABLE\n");
-+
-+ /* dev may initiate HNP */
-+ if (otg_cap_param == DWC_OTG_CAP_PARAM_HNP_SRP_CAPABLE) {
-+ pcd->b_hnp_enable = 1;
-+ dwc_otg_pcd_update_otg(pcd, 0);
-+ DWC_DEBUGPL(DBG_PCD, "Request B HNP\n");
-+ /**@todo Is the gotgctl.devhnpen cleared
-+ * by a USB Reset? */
-+ gotgctl.b.devhnpen = 1;
-+ gotgctl.b.hnpreq = 1;
-+ DWC_WRITE_REG32(&global_regs->gotgctl,
-+ gotgctl.d32);
-+ } else {
-+ ep0_do_stall(pcd, -DWC_E_NOT_SUPPORTED);
-+ return;
-+ }
-+ break;
-+
-+ case UF_DEVICE_A_HNP_SUPPORT:
-+ /* RH port supports HNP */
-+ DWC_DEBUGPL(DBG_PCDV,
-+ "SET_FEATURE: USB_DEVICE_A_HNP_SUPPORT\n");
-+ if (otg_cap_param == DWC_OTG_CAP_PARAM_HNP_SRP_CAPABLE) {
-+ pcd->a_hnp_support = 1;
-+ dwc_otg_pcd_update_otg(pcd, 0);
-+ } else {
-+ ep0_do_stall(pcd, -DWC_E_NOT_SUPPORTED);
-+ return;
-+ }
-+ break;
-+
-+ case UF_DEVICE_A_ALT_HNP_SUPPORT:
-+ /* other RH port does */
-+ DWC_DEBUGPL(DBG_PCDV,
-+ "SET_FEATURE: USB_DEVICE_A_ALT_HNP_SUPPORT\n");
-+ if (otg_cap_param == DWC_OTG_CAP_PARAM_HNP_SRP_CAPABLE) {
-+ pcd->a_alt_hnp_support = 1;
-+ dwc_otg_pcd_update_otg(pcd, 0);
-+ } else {
-+ ep0_do_stall(pcd, -DWC_E_NOT_SUPPORTED);
-+ return;
-+ }
-+ break;
-+
-+ default:
-+ ep0_do_stall(pcd, -DWC_E_NOT_SUPPORTED);
-+ return;
-+
-+ }
-+ do_setup_in_status_phase(pcd);
-+ break;
-+
-+ case UT_INTERFACE:
-+ do_gadget_setup(pcd, &ctrl);
-+ break;
-+
-+ case UT_ENDPOINT:
-+ if (UGETW(ctrl.wValue) == UF_ENDPOINT_HALT) {
-+ ep = get_ep_by_addr(pcd, UGETW(ctrl.wIndex));
-+ if (ep == 0) {
-+ ep0_do_stall(pcd, -DWC_E_NOT_SUPPORTED);
-+ return;
-+ }
-+ ep->stopped = 1;
-+ dwc_otg_ep_set_stall(core_if, &ep->dwc_ep);
-+ }
-+ do_setup_in_status_phase(pcd);
-+ break;
-+ }
-+}
-+
-+/**
-+ * This function process the CLEAR_FEATURE Setup Commands.
-+ */
-+static inline void do_clear_feature(dwc_otg_pcd_t * pcd)
-+{
-+ usb_device_request_t ctrl = pcd->setup_pkt->req;
-+ dwc_otg_pcd_ep_t *ep = 0;
-+
-+ DWC_DEBUGPL(DBG_PCD,
-+ "CLEAR_FEATURE:%02x.%02x v%04x i%04x l%04x\n",
-+ ctrl.bmRequestType, ctrl.bRequest,
-+ UGETW(ctrl.wValue), UGETW(ctrl.wIndex),
-+ UGETW(ctrl.wLength));
-+
-+ switch (UT_GET_RECIPIENT(ctrl.bmRequestType)) {
-+ case UT_DEVICE:
-+ switch (UGETW(ctrl.wValue)) {
-+ case UF_DEVICE_REMOTE_WAKEUP:
-+ pcd->remote_wakeup_enable = 0;
-+ break;
-+
-+ case UF_TEST_MODE:
-+ /** @todo Add CLEAR_FEATURE for TEST modes. */
-+ break;
-+
-+ default:
-+ ep0_do_stall(pcd, -DWC_E_NOT_SUPPORTED);
-+ return;
-+ }
-+ do_setup_in_status_phase(pcd);
-+ break;
-+
-+ case UT_ENDPOINT:
-+ ep = get_ep_by_addr(pcd, UGETW(ctrl.wIndex));
-+ if (ep == 0) {
-+ ep0_do_stall(pcd, -DWC_E_NOT_SUPPORTED);
-+ return;
-+ }
-+
-+ pcd_clear_halt(pcd, ep);
-+
-+ break;
-+ }
-+}
-+
-+/**
-+ * This function process the SET_ADDRESS Setup Commands.
-+ */
-+static inline void do_set_address(dwc_otg_pcd_t * pcd)
-+{
-+ dwc_otg_dev_if_t *dev_if = GET_CORE_IF(pcd)->dev_if;
-+ usb_device_request_t ctrl = pcd->setup_pkt->req;
-+
-+ if (ctrl.bmRequestType == UT_DEVICE) {
-+ dcfg_data_t dcfg = {.d32 = 0 };
-+
-+#ifdef DEBUG_EP0
-+// DWC_DEBUGPL(DBG_PCDV, "SET_ADDRESS:%d\n", ctrl.wValue);
-+#endif
-+ dcfg.b.devaddr = UGETW(ctrl.wValue);
-+ DWC_MODIFY_REG32(&dev_if->dev_global_regs->dcfg, 0, dcfg.d32);
-+ do_setup_in_status_phase(pcd);
-+ }
-+}
-+
-+/**
-+ * This function processes SETUP commands. In Linux, the USB Command
-+ * processing is done in two places - the first being the PCD and the
-+ * second in the Gadget Driver (for example, the File-Backed Storage
-+ * Gadget Driver).
-+ *
-+ * <table>
-+ * <tr><td>Command </td><td>Driver </td><td>Description</td></tr>
-+ *
-+ * <tr><td>GET_STATUS </td><td>PCD </td><td>Command is processed as
-+ * defined in chapter 9 of the USB 2.0 Specification chapter 9
-+ * </td></tr>
-+ *
-+ * <tr><td>CLEAR_FEATURE </td><td>PCD </td><td>The Device and Endpoint
-+ * requests are the ENDPOINT_HALT feature is procesed, all others the
-+ * interface requests are ignored.</td></tr>
-+ *
-+ * <tr><td>SET_FEATURE </td><td>PCD </td><td>The Device and Endpoint
-+ * requests are processed by the PCD. Interface requests are passed
-+ * to the Gadget Driver.</td></tr>
-+ *
-+ * <tr><td>SET_ADDRESS </td><td>PCD </td><td>Program the DCFG reg,
-+ * with device address received </td></tr>
-+ *
-+ * <tr><td>GET_DESCRIPTOR </td><td>Gadget Driver </td><td>Return the
-+ * requested descriptor</td></tr>
-+ *
-+ * <tr><td>SET_DESCRIPTOR </td><td>Gadget Driver </td><td>Optional -
-+ * not implemented by any of the existing Gadget Drivers.</td></tr>
-+ *
-+ * <tr><td>SET_CONFIGURATION </td><td>Gadget Driver </td><td>Disable
-+ * all EPs and enable EPs for new configuration.</td></tr>
-+ *
-+ * <tr><td>GET_CONFIGURATION </td><td>Gadget Driver </td><td>Return
-+ * the current configuration</td></tr>
-+ *
-+ * <tr><td>SET_INTERFACE </td><td>Gadget Driver </td><td>Disable all
-+ * EPs and enable EPs for new configuration.</td></tr>
-+ *
-+ * <tr><td>GET_INTERFACE </td><td>Gadget Driver </td><td>Return the
-+ * current interface.</td></tr>
-+ *
-+ * <tr><td>SYNC_FRAME </td><td>PCD </td><td>Display debug
-+ * message.</td></tr>
-+ * </table>
-+ *
-+ * When the SETUP Phase Done interrupt occurs, the PCD SETUP commands are
-+ * processed by pcd_setup. Calling the Function Driver's setup function from
-+ * pcd_setup processes the gadget SETUP commands.
-+ */
-+static inline void pcd_setup(dwc_otg_pcd_t * pcd)
-+{
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+ dwc_otg_dev_if_t *dev_if = core_if->dev_if;
-+ usb_device_request_t ctrl = pcd->setup_pkt->req;
-+ dwc_otg_pcd_ep_t *ep0 = &pcd->ep0;
-+
-+ deptsiz0_data_t doeptsize0 = {.d32 = 0 };
-+
-+#ifdef DWC_UTE_CFI
-+ int retval = 0;
-+ struct cfi_usb_ctrlrequest cfi_req;
-+#endif
-+
-+ doeptsize0.d32 = DWC_READ_REG32(&dev_if->out_ep_regs[0]->doeptsiz);
-+
-+ /** In BDMA more then 1 setup packet is not supported till 3.00a */
-+ if (core_if->dma_enable && core_if->dma_desc_enable == 0
-+ && (doeptsize0.b.supcnt < 2)
-+ && (core_if->snpsid < OTG_CORE_REV_2_94a)) {
-+ DWC_ERROR
-+ ("\n\n----------- CANNOT handle > 1 setup packet in DMA mode\n\n");
-+ }
-+ if ((core_if->snpsid >= OTG_CORE_REV_3_00a)
-+ && (core_if->dma_enable == 1) && (core_if->dma_desc_enable == 0)) {
-+ ctrl =
-+ (pcd->setup_pkt +
-+ (3 - doeptsize0.b.supcnt - 1 +
-+ ep0->dwc_ep.stp_rollover))->req;
-+ }
-+#ifdef DEBUG_EP0
-+ DWC_DEBUGPL(DBG_PCD, "SETUP %02x.%02x v%04x i%04x l%04x\n",
-+ ctrl.bmRequestType, ctrl.bRequest,
-+ UGETW(ctrl.wValue), UGETW(ctrl.wIndex),
-+ UGETW(ctrl.wLength));
-+#endif
-+
-+ /* Clean up the request queue */
-+ dwc_otg_request_nuke(ep0);
-+ ep0->stopped = 0;
-+
-+ if (ctrl.bmRequestType & UE_DIR_IN) {
-+ ep0->dwc_ep.is_in = 1;
-+ pcd->ep0state = EP0_IN_DATA_PHASE;
-+ } else {
-+ ep0->dwc_ep.is_in = 0;
-+ pcd->ep0state = EP0_OUT_DATA_PHASE;
-+ }
-+
-+ if (UGETW(ctrl.wLength) == 0) {
-+ ep0->dwc_ep.is_in = 1;
-+ pcd->ep0state = EP0_IN_STATUS_PHASE;
-+ }
-+
-+ if (UT_GET_TYPE(ctrl.bmRequestType) != UT_STANDARD) {
-+
-+#ifdef DWC_UTE_CFI
-+ DWC_MEMCPY(&cfi_req, &ctrl, sizeof(usb_device_request_t));
-+
-+ //printk(KERN_ALERT "CFI: req_type=0x%02x; req=0x%02x\n",
-+ ctrl.bRequestType, ctrl.bRequest);
-+ if (UT_GET_TYPE(cfi_req.bRequestType) == UT_VENDOR) {
-+ if (cfi_req.bRequest > 0xB0 && cfi_req.bRequest < 0xBF) {
-+ retval = cfi_setup(pcd, &cfi_req);
-+ if (retval < 0) {
-+ ep0_do_stall(pcd, retval);
-+ pcd->ep0_pending = 0;
-+ return;
-+ }
-+
-+ /* if need gadget setup then call it and check the retval */
-+ if (pcd->cfi->need_gadget_att) {
-+ retval =
-+ cfi_gadget_setup(pcd,
-+ &pcd->
-+ cfi->ctrl_req);
-+ if (retval < 0) {
-+ pcd->ep0_pending = 0;
-+ return;
-+ }
-+ }
-+
-+ if (pcd->cfi->need_status_in_complete) {
-+ do_setup_in_status_phase(pcd);
-+ }
-+ return;
-+ }
-+ }
-+#endif
-+
-+ /* handle non-standard (class/vendor) requests in the gadget driver */
-+ do_gadget_setup(pcd, &ctrl);
-+ return;
-+ }
-+
-+ /** @todo NGS: Handle bad setup packet? */
-+
-+///////////////////////////////////////////
-+//// --- Standard Request handling --- ////
-+
-+ switch (ctrl.bRequest) {
-+ case UR_GET_STATUS:
-+ do_get_status(pcd);
-+ break;
-+
-+ case UR_CLEAR_FEATURE:
-+ do_clear_feature(pcd);
-+ break;
-+
-+ case UR_SET_FEATURE:
-+ do_set_feature(pcd);
-+ break;
-+
-+ case UR_SET_ADDRESS:
-+ do_set_address(pcd);
-+ break;
-+
-+ case UR_SET_INTERFACE:
-+ case UR_SET_CONFIG:
-+// _pcd->request_config = 1; /* Configuration changed */
-+ do_gadget_setup(pcd, &ctrl);
-+ break;
-+
-+ case UR_SYNCH_FRAME:
-+ do_gadget_setup(pcd, &ctrl);
-+ break;
-+
-+ default:
-+ /* Call the Gadget Driver's setup functions */
-+ do_gadget_setup(pcd, &ctrl);
-+ break;
-+ }
-+}
-+
-+/**
-+ * This function completes the ep0 control transfer.
-+ */
-+static int32_t ep0_complete_request(dwc_otg_pcd_ep_t * ep)
-+{
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(ep->pcd);
-+ dwc_otg_dev_if_t *dev_if = core_if->dev_if;
-+ dwc_otg_dev_in_ep_regs_t *in_ep_regs =
-+ dev_if->in_ep_regs[ep->dwc_ep.num];
-+#ifdef DEBUG_EP0
-+ dwc_otg_dev_out_ep_regs_t *out_ep_regs =
-+ dev_if->out_ep_regs[ep->dwc_ep.num];
-+#endif
-+ deptsiz0_data_t deptsiz;
-+ dev_dma_desc_sts_t desc_sts;
-+ dwc_otg_pcd_request_t *req;
-+ int is_last = 0;
-+ dwc_otg_pcd_t *pcd = ep->pcd;
-+
-+#ifdef DWC_UTE_CFI
-+ struct cfi_usb_ctrlrequest *ctrlreq;
-+ int retval = -DWC_E_NOT_SUPPORTED;
-+#endif
-+
-+ desc_sts.b.bytes = 0;
-+
-+ if (pcd->ep0_pending && DWC_CIRCLEQ_EMPTY(&ep->queue)) {
-+ if (ep->dwc_ep.is_in) {
-+#ifdef DEBUG_EP0
-+ DWC_DEBUGPL(DBG_PCDV, "Do setup OUT status phase\n");
-+#endif
-+ do_setup_out_status_phase(pcd);
-+ } else {
-+#ifdef DEBUG_EP0
-+ DWC_DEBUGPL(DBG_PCDV, "Do setup IN status phase\n");
-+#endif
-+
-+#ifdef DWC_UTE_CFI
-+ ctrlreq = &pcd->cfi->ctrl_req;
-+
-+ if (UT_GET_TYPE(ctrlreq->bRequestType) == UT_VENDOR) {
-+ if (ctrlreq->bRequest > 0xB0
-+ && ctrlreq->bRequest < 0xBF) {
-+
-+ /* Return if the PCD failed to handle the request */
-+ if ((retval =
-+ pcd->cfi->ops.
-+ ctrl_write_complete(pcd->cfi,
-+ pcd)) < 0) {
-+ CFI_INFO
-+ ("ERROR setting a new value in the PCD(%d)\n",
-+ retval);
-+ ep0_do_stall(pcd, retval);
-+ pcd->ep0_pending = 0;
-+ return 0;
-+ }
-+
-+ /* If the gadget needs to be notified on the request */
-+ if (pcd->cfi->need_gadget_att == 1) {
-+ //retval = do_gadget_setup(pcd, &pcd->cfi->ctrl_req);
-+ retval =
-+ cfi_gadget_setup(pcd,
-+ &pcd->cfi->
-+ ctrl_req);
-+
-+ /* Return from the function if the gadget failed to process
-+ * the request properly - this should never happen !!!
-+ */
-+ if (retval < 0) {
-+ CFI_INFO
-+ ("ERROR setting a new value in the gadget(%d)\n",
-+ retval);
-+ pcd->ep0_pending = 0;
-+ return 0;
-+ }
-+ }
-+
-+ CFI_INFO("%s: RETVAL=%d\n", __func__,
-+ retval);
-+ /* If we hit here then the PCD and the gadget has properly
-+ * handled the request - so send the ZLP IN to the host.
-+ */
-+ /* @todo: MAS - decide whether we need to start the setup
-+ * stage based on the need_setup value of the cfi object
-+ */
-+ do_setup_in_status_phase(pcd);
-+ pcd->ep0_pending = 0;
-+ return 1;
-+ }
-+ }
-+#endif
-+
-+ do_setup_in_status_phase(pcd);
-+ }
-+ pcd->ep0_pending = 0;
-+ return 1;
-+ }
-+
-+ if (DWC_CIRCLEQ_EMPTY(&ep->queue)) {
-+ return 0;
-+ }
-+ req = DWC_CIRCLEQ_FIRST(&ep->queue);
-+
-+ if (pcd->ep0state == EP0_OUT_STATUS_PHASE
-+ || pcd->ep0state == EP0_IN_STATUS_PHASE) {
-+ is_last = 1;
-+ } else if (ep->dwc_ep.is_in) {
-+ deptsiz.d32 = DWC_READ_REG32(&in_ep_regs->dieptsiz);
-+ if (core_if->dma_desc_enable != 0)
-+ desc_sts = dev_if->in_desc_addr->status;
-+#ifdef DEBUG_EP0
-+ DWC_DEBUGPL(DBG_PCDV, "%d len=%d xfersize=%d pktcnt=%d\n",
-+ ep->dwc_ep.num, ep->dwc_ep.xfer_len,
-+ deptsiz.b.xfersize, deptsiz.b.pktcnt);
-+#endif
-+
-+ if (((core_if->dma_desc_enable == 0)
-+ && (deptsiz.b.xfersize == 0))
-+ || ((core_if->dma_desc_enable != 0)
-+ && (desc_sts.b.bytes == 0))) {
-+ req->actual = ep->dwc_ep.xfer_count;
-+ /* Is a Zero Len Packet needed? */
-+ if (req->sent_zlp) {
-+#ifdef DEBUG_EP0
-+ DWC_DEBUGPL(DBG_PCD, "Setup Rx ZLP\n");
-+#endif
-+ req->sent_zlp = 0;
-+ }
-+ do_setup_out_status_phase(pcd);
-+ }
-+ } else {
-+ /* ep0-OUT */
-+#ifdef DEBUG_EP0
-+ deptsiz.d32 = DWC_READ_REG32(&out_ep_regs->doeptsiz);
-+ DWC_DEBUGPL(DBG_PCDV, "%d len=%d xsize=%d pktcnt=%d\n",
-+ ep->dwc_ep.num, ep->dwc_ep.xfer_len,
-+ deptsiz.b.xfersize, deptsiz.b.pktcnt);
-+#endif
-+ req->actual = ep->dwc_ep.xfer_count;
-+
-+ /* Is a Zero Len Packet needed? */
-+ if (req->sent_zlp) {
-+#ifdef DEBUG_EP0
-+ DWC_DEBUGPL(DBG_PCDV, "Setup Tx ZLP\n");
-+#endif
-+ req->sent_zlp = 0;
-+ }
-+ /* For older cores do setup in status phase in Slave/BDMA modes,
-+ * starting from 3.00 do that only in slave, and for DMA modes
-+ * just re-enable ep 0 OUT here*/
-+ if (core_if->dma_enable == 0
-+ || (core_if->dma_desc_enable == 0
-+ && core_if->snpsid <= OTG_CORE_REV_2_94a)) {
-+ do_setup_in_status_phase(pcd);
-+ } else if (core_if->snpsid >= OTG_CORE_REV_3_00a) {
-+ DWC_DEBUGPL(DBG_PCDV,
-+ "Enable out ep before in status phase\n");
-+ ep0_out_start(core_if, pcd);
-+ }
-+ }
-+
-+ /* Complete the request */
-+ if (is_last) {
-+ dwc_otg_request_done(ep, req, 0);
-+ ep->dwc_ep.start_xfer_buff = 0;
-+ ep->dwc_ep.xfer_buff = 0;
-+ ep->dwc_ep.xfer_len = 0;
-+ return 1;
-+ }
-+ return 0;
-+}
-+
-+#ifdef DWC_UTE_CFI
-+/**
-+ * This function calculates traverses all the CFI DMA descriptors and
-+ * and accumulates the bytes that are left to be transfered.
-+ *
-+ * @return The total bytes left to transfered, or a negative value as failure
-+ */
-+static inline int cfi_calc_desc_residue(dwc_otg_pcd_ep_t * ep)
-+{
-+ int32_t ret = 0;
-+ int i;
-+ struct dwc_otg_dma_desc *ddesc = NULL;
-+ struct cfi_ep *cfiep;
-+
-+ /* See if the pcd_ep has its respective cfi_ep mapped */
-+ cfiep = get_cfi_ep_by_pcd_ep(ep->pcd->cfi, ep);
-+ if (!cfiep) {
-+ CFI_INFO("%s: Failed to find ep\n", __func__);
-+ return -1;
-+ }
-+
-+ ddesc = ep->dwc_ep.descs;
-+
-+ for (i = 0; (i < cfiep->desc_count) && (i < MAX_DMA_DESCS_PER_EP); i++) {
-+
-+#if defined(PRINT_CFI_DMA_DESCS)
-+ print_desc(ddesc, ep->ep.name, i);
-+#endif
-+ ret += ddesc->status.b.bytes;
-+ ddesc++;
-+ }
-+
-+ if (ret)
-+ CFI_INFO("!!!!!!!!!! WARNING (%s) - residue=%d\n", __func__,
-+ ret);
-+
-+ return ret;
-+}
-+#endif
-+
-+/**
-+ * This function completes the request for the EP. If there are
-+ * additional requests for the EP in the queue they will be started.
-+ */
-+static void complete_ep(dwc_otg_pcd_ep_t * ep)
-+{
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(ep->pcd);
-+ dwc_otg_dev_if_t *dev_if = core_if->dev_if;
-+ dwc_otg_dev_in_ep_regs_t *in_ep_regs =
-+ dev_if->in_ep_regs[ep->dwc_ep.num];
-+ deptsiz_data_t deptsiz;
-+ dev_dma_desc_sts_t desc_sts;
-+ dwc_otg_pcd_request_t *req = 0;
-+ dwc_otg_dev_dma_desc_t *dma_desc;
-+ uint32_t byte_count = 0;
-+ int is_last = 0;
-+ int i;
-+
-+ DWC_DEBUGPL(DBG_PCDV, "%s() %d-%s\n", __func__, ep->dwc_ep.num,
-+ (ep->dwc_ep.is_in ? "IN" : "OUT"));
-+
-+ /* Get any pending requests */
-+ if (!DWC_CIRCLEQ_EMPTY(&ep->queue)) {
-+ req = DWC_CIRCLEQ_FIRST(&ep->queue);
-+ if (!req) {
-+ DWC_PRINTF("complete_ep 0x%p, req = NULL!\n", ep);
-+ return;
-+ }
-+ } else {
-+ DWC_PRINTF("complete_ep 0x%p, ep->queue empty!\n", ep);
-+ return;
-+ }
-+
-+ DWC_DEBUGPL(DBG_PCD, "Requests %d\n", ep->pcd->request_pending);
-+
-+ if (ep->dwc_ep.is_in) {
-+ deptsiz.d32 = DWC_READ_REG32(&in_ep_regs->dieptsiz);
-+
-+ if (core_if->dma_enable) {
-+ if (core_if->dma_desc_enable == 0) {
-+ if (deptsiz.b.xfersize == 0
-+ && deptsiz.b.pktcnt == 0) {
-+ byte_count =
-+ ep->dwc_ep.xfer_len -
-+ ep->dwc_ep.xfer_count;
-+
-+ ep->dwc_ep.xfer_buff += byte_count;
-+ ep->dwc_ep.dma_addr += byte_count;
-+ ep->dwc_ep.xfer_count += byte_count;
-+
-+ DWC_DEBUGPL(DBG_PCDV,
-+ "%d-%s len=%d xfersize=%d pktcnt=%d\n",
-+ ep->dwc_ep.num,
-+ (ep->dwc_ep.
-+ is_in ? "IN" : "OUT"),
-+ ep->dwc_ep.xfer_len,
-+ deptsiz.b.xfersize,
-+ deptsiz.b.pktcnt);
-+
-+ if (ep->dwc_ep.xfer_len <
-+ ep->dwc_ep.total_len) {
-+ dwc_otg_ep_start_transfer
-+ (core_if, &ep->dwc_ep);
-+ } else if (ep->dwc_ep.sent_zlp) {
-+ /*
-+ * This fragment of code should initiate 0
-+ * length transfer in case if it is queued
-+ * a transfer with size divisible to EPs max
-+ * packet size and with usb_request zero field
-+ * is set, which means that after data is transfered,
-+ * it is also should be transfered
-+ * a 0 length packet at the end. For Slave and
-+ * Buffer DMA modes in this case SW has
-+ * to initiate 2 transfers one with transfer size,
-+ * and the second with 0 size. For Descriptor
-+ * DMA mode SW is able to initiate a transfer,
-+ * which will handle all the packets including
-+ * the last 0 length.
-+ */
-+ ep->dwc_ep.sent_zlp = 0;
-+ dwc_otg_ep_start_zl_transfer
-+ (core_if, &ep->dwc_ep);
-+ } else {
-+ is_last = 1;
-+ }
-+ } else {
-+ if (ep->dwc_ep.type ==
-+ DWC_OTG_EP_TYPE_ISOC) {
-+ req->actual = 0;
-+ dwc_otg_request_done(ep, req, 0);
-+
-+ ep->dwc_ep.start_xfer_buff = 0;
-+ ep->dwc_ep.xfer_buff = 0;
-+ ep->dwc_ep.xfer_len = 0;
-+
-+ /* If there is a request in the queue start it. */
-+ start_next_request(ep);
-+ } else
-+ DWC_WARN
-+ ("Incomplete transfer (%d - %s [siz=%d pkt=%d])\n",
-+ ep->dwc_ep.num,
-+ (ep->dwc_ep.is_in ? "IN" : "OUT"),
-+ deptsiz.b.xfersize,
-+ deptsiz.b.pktcnt);
-+ }
-+ } else {
-+ dma_desc = ep->dwc_ep.desc_addr;
-+ byte_count = 0;
-+ ep->dwc_ep.sent_zlp = 0;
-+
-+#ifdef DWC_UTE_CFI
-+ CFI_INFO("%s: BUFFER_MODE=%d\n", __func__,
-+ ep->dwc_ep.buff_mode);
-+ if (ep->dwc_ep.buff_mode != BM_STANDARD) {
-+ int residue;
-+
-+ residue = cfi_calc_desc_residue(ep);
-+ if (residue < 0)
-+ return;
-+
-+ byte_count = residue;
-+ } else {
-+#endif
-+ for (i = 0; i < ep->dwc_ep.desc_cnt;
-+ ++i) {
-+ desc_sts = dma_desc->status;
-+ byte_count += desc_sts.b.bytes;
-+ dma_desc++;
-+ }
-+#ifdef DWC_UTE_CFI
-+ }
-+#endif
-+ if (byte_count == 0) {
-+ ep->dwc_ep.xfer_count =
-+ ep->dwc_ep.total_len;
-+ is_last = 1;
-+ } else {
-+ DWC_WARN("Incomplete transfer\n");
-+ }
-+ }
-+ } else {
-+ if (deptsiz.b.xfersize == 0 && deptsiz.b.pktcnt == 0) {
-+ DWC_DEBUGPL(DBG_PCDV,
-+ "%d-%s len=%d xfersize=%d pktcnt=%d\n",
-+ ep->dwc_ep.num,
-+ ep->dwc_ep.is_in ? "IN" : "OUT",
-+ ep->dwc_ep.xfer_len,
-+ deptsiz.b.xfersize,
-+ deptsiz.b.pktcnt);
-+
-+ /* Check if the whole transfer was completed,
-+ * if no, setup transfer for next portion of data
-+ */
-+ if (ep->dwc_ep.xfer_len < ep->dwc_ep.total_len) {
-+ dwc_otg_ep_start_transfer(core_if,
-+ &ep->dwc_ep);
-+ } else if (ep->dwc_ep.sent_zlp) {
-+ /*
-+ * This fragment of code should initiate 0
-+ * length trasfer in case if it is queued
-+ * a trasfer with size divisible to EPs max
-+ * packet size and with usb_request zero field
-+ * is set, which means that after data is transfered,
-+ * it is also should be transfered
-+ * a 0 length packet at the end. For Slave and
-+ * Buffer DMA modes in this case SW has
-+ * to initiate 2 transfers one with transfer size,
-+ * and the second with 0 size. For Desriptor
-+ * DMA mode SW is able to initiate a transfer,
-+ * which will handle all the packets including
-+ * the last 0 legth.
-+ */
-+ ep->dwc_ep.sent_zlp = 0;
-+ dwc_otg_ep_start_zl_transfer(core_if,
-+ &ep->dwc_ep);
-+ } else {
-+ is_last = 1;
-+ }
-+ } else {
-+ DWC_WARN
-+ ("Incomplete transfer (%d-%s [siz=%d pkt=%d])\n",
-+ ep->dwc_ep.num,
-+ (ep->dwc_ep.is_in ? "IN" : "OUT"),
-+ deptsiz.b.xfersize, deptsiz.b.pktcnt);
-+ }
-+ }
-+ } else {
-+ dwc_otg_dev_out_ep_regs_t *out_ep_regs =
-+ dev_if->out_ep_regs[ep->dwc_ep.num];
-+ desc_sts.d32 = 0;
-+ if (core_if->dma_enable) {
-+ if (core_if->dma_desc_enable) {
-+ dma_desc = ep->dwc_ep.desc_addr;
-+ byte_count = 0;
-+ ep->dwc_ep.sent_zlp = 0;
-+
-+#ifdef DWC_UTE_CFI
-+ CFI_INFO("%s: BUFFER_MODE=%d\n", __func__,
-+ ep->dwc_ep.buff_mode);
-+ if (ep->dwc_ep.buff_mode != BM_STANDARD) {
-+ int residue;
-+ residue = cfi_calc_desc_residue(ep);
-+ if (residue < 0)
-+ return;
-+ byte_count = residue;
-+ } else {
-+#endif
-+
-+ for (i = 0; i < ep->dwc_ep.desc_cnt;
-+ ++i) {
-+ desc_sts = dma_desc->status;
-+ byte_count += desc_sts.b.bytes;
-+ dma_desc++;
-+ }
-+
-+#ifdef DWC_UTE_CFI
-+ }
-+#endif
-+ /* Checking for interrupt Out transfers with not
-+ * dword aligned mps sizes
-+ */
-+ if (ep->dwc_ep.type == DWC_OTG_EP_TYPE_INTR &&
-+ (ep->dwc_ep.maxpacket%4)) {
-+ ep->dwc_ep.xfer_count =
-+ ep->dwc_ep.total_len - byte_count;
-+ if ((ep->dwc_ep.xfer_len %
-+ ep->dwc_ep.maxpacket)
-+ && (ep->dwc_ep.xfer_len /
-+ ep->dwc_ep.maxpacket <
-+ MAX_DMA_DESC_CNT))
-+ ep->dwc_ep.xfer_len -=
-+ (ep->dwc_ep.desc_cnt -
-+ 1) * ep->dwc_ep.maxpacket +
-+ ep->dwc_ep.xfer_len %
-+ ep->dwc_ep.maxpacket;
-+ else
-+ ep->dwc_ep.xfer_len -=
-+ ep->dwc_ep.desc_cnt *
-+ ep->dwc_ep.maxpacket;
-+ if (ep->dwc_ep.xfer_len > 0) {
-+ dwc_otg_ep_start_transfer
-+ (core_if, &ep->dwc_ep);
-+ } else {
-+ is_last = 1;
-+ }
-+ } else {
-+ ep->dwc_ep.xfer_count =
-+ ep->dwc_ep.total_len - byte_count +
-+ ((4 -
-+ (ep->dwc_ep.
-+ total_len & 0x3)) & 0x3);
-+ is_last = 1;
-+ }
-+ } else {
-+ deptsiz.d32 = 0;
-+ deptsiz.d32 =
-+ DWC_READ_REG32(&out_ep_regs->doeptsiz);
-+
-+ byte_count = (ep->dwc_ep.xfer_len -
-+ ep->dwc_ep.xfer_count -
-+ deptsiz.b.xfersize);
-+ ep->dwc_ep.xfer_buff += byte_count;
-+ ep->dwc_ep.dma_addr += byte_count;
-+ ep->dwc_ep.xfer_count += byte_count;
-+
-+ /* Check if the whole transfer was completed,
-+ * if no, setup transfer for next portion of data
-+ */
-+ if (ep->dwc_ep.xfer_len < ep->dwc_ep.total_len) {
-+ dwc_otg_ep_start_transfer(core_if,
-+ &ep->dwc_ep);
-+ } else if (ep->dwc_ep.sent_zlp) {
-+ /*
-+ * This fragment of code should initiate 0
-+ * length trasfer in case if it is queued
-+ * a trasfer with size divisible to EPs max
-+ * packet size and with usb_request zero field
-+ * is set, which means that after data is transfered,
-+ * it is also should be transfered
-+ * a 0 length packet at the end. For Slave and
-+ * Buffer DMA modes in this case SW has
-+ * to initiate 2 transfers one with transfer size,
-+ * and the second with 0 size. For Desriptor
-+ * DMA mode SW is able to initiate a transfer,
-+ * which will handle all the packets including
-+ * the last 0 legth.
-+ */
-+ ep->dwc_ep.sent_zlp = 0;
-+ dwc_otg_ep_start_zl_transfer(core_if,
-+ &ep->dwc_ep);
-+ } else {
-+ is_last = 1;
-+ }
-+ }
-+ } else {
-+ /* Check if the whole transfer was completed,
-+ * if no, setup transfer for next portion of data
-+ */
-+ if (ep->dwc_ep.xfer_len < ep->dwc_ep.total_len) {
-+ dwc_otg_ep_start_transfer(core_if, &ep->dwc_ep);
-+ } else if (ep->dwc_ep.sent_zlp) {
-+ /*
-+ * This fragment of code should initiate 0
-+ * length transfer in case if it is queued
-+ * a transfer with size divisible to EPs max
-+ * packet size and with usb_request zero field
-+ * is set, which means that after data is transfered,
-+ * it is also should be transfered
-+ * a 0 length packet at the end. For Slave and
-+ * Buffer DMA modes in this case SW has
-+ * to initiate 2 transfers one with transfer size,
-+ * and the second with 0 size. For Descriptor
-+ * DMA mode SW is able to initiate a transfer,
-+ * which will handle all the packets including
-+ * the last 0 length.
-+ */
-+ ep->dwc_ep.sent_zlp = 0;
-+ dwc_otg_ep_start_zl_transfer(core_if,
-+ &ep->dwc_ep);
-+ } else {
-+ is_last = 1;
-+ }
-+ }
-+
-+ DWC_DEBUGPL(DBG_PCDV,
-+ "addr %p, %d-%s len=%d cnt=%d xsize=%d pktcnt=%d\n",
-+ &out_ep_regs->doeptsiz, ep->dwc_ep.num,
-+ ep->dwc_ep.is_in ? "IN" : "OUT",
-+ ep->dwc_ep.xfer_len, ep->dwc_ep.xfer_count,
-+ deptsiz.b.xfersize, deptsiz.b.pktcnt);
-+ }
-+
-+ /* Complete the request */
-+ if (is_last) {
-+#ifdef DWC_UTE_CFI
-+ if (ep->dwc_ep.buff_mode != BM_STANDARD) {
-+ req->actual = ep->dwc_ep.cfi_req_len - byte_count;
-+ } else {
-+#endif
-+ req->actual = ep->dwc_ep.xfer_count;
-+#ifdef DWC_UTE_CFI
-+ }
-+#endif
-+ if (req->dw_align_buf) {
-+ if (!ep->dwc_ep.is_in) {
-+ dwc_memcpy(req->buf, req->dw_align_buf, req->length);
-+ }
-+ DWC_DMA_FREE(req->length, req->dw_align_buf,
-+ req->dw_align_buf_dma);
-+ }
-+
-+ dwc_otg_request_done(ep, req, 0);
-+
-+ ep->dwc_ep.start_xfer_buff = 0;
-+ ep->dwc_ep.xfer_buff = 0;
-+ ep->dwc_ep.xfer_len = 0;
-+
-+ /* If there is a request in the queue start it. */
-+ start_next_request(ep);
-+ }
-+}
-+
-+#ifdef DWC_EN_ISOC
-+
-+/**
-+ * This function BNA interrupt for Isochronous EPs
-+ *
-+ */
-+static void dwc_otg_pcd_handle_iso_bna(dwc_otg_pcd_ep_t * ep)
-+{
-+ dwc_ep_t *dwc_ep = &ep->dwc_ep;
-+ volatile uint32_t *addr;
-+ depctl_data_t depctl = {.d32 = 0 };
-+ dwc_otg_pcd_t *pcd = ep->pcd;
-+ dwc_otg_dev_dma_desc_t *dma_desc;
-+ int i;
-+
-+ dma_desc =
-+ dwc_ep->iso_desc_addr + dwc_ep->desc_cnt * (dwc_ep->proc_buf_num);
-+
-+ if (dwc_ep->is_in) {
-+ dev_dma_desc_sts_t sts = {.d32 = 0 };
-+ for (i = 0; i < dwc_ep->desc_cnt; ++i, ++dma_desc) {
-+ sts.d32 = dma_desc->status.d32;
-+ sts.b_iso_in.bs = BS_HOST_READY;
-+ dma_desc->status.d32 = sts.d32;
-+ }
-+ } else {
-+ dev_dma_desc_sts_t sts = {.d32 = 0 };
-+ for (i = 0; i < dwc_ep->desc_cnt; ++i, ++dma_desc) {
-+ sts.d32 = dma_desc->status.d32;
-+ sts.b_iso_out.bs = BS_HOST_READY;
-+ dma_desc->status.d32 = sts.d32;
-+ }
-+ }
-+
-+ if (dwc_ep->is_in == 0) {
-+ addr =
-+ &GET_CORE_IF(pcd)->dev_if->out_ep_regs[dwc_ep->
-+ num]->doepctl;
-+ } else {
-+ addr =
-+ &GET_CORE_IF(pcd)->dev_if->in_ep_regs[dwc_ep->num]->diepctl;
-+ }
-+ depctl.b.epena = 1;
-+ DWC_MODIFY_REG32(addr, depctl.d32, depctl.d32);
-+}
-+
-+/**
-+ * This function sets latest iso packet information(non-PTI mode)
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param ep The EP to start the transfer on.
-+ *
-+ */
-+void set_current_pkt_info(dwc_otg_core_if_t * core_if, dwc_ep_t * ep)
-+{
-+ deptsiz_data_t deptsiz = {.d32 = 0 };
-+ dma_addr_t dma_addr;
-+ uint32_t offset;
-+
-+ if (ep->proc_buf_num)
-+ dma_addr = ep->dma_addr1;
-+ else
-+ dma_addr = ep->dma_addr0;
-+
-+ if (ep->is_in) {
-+ deptsiz.d32 =
-+ DWC_READ_REG32(&core_if->dev_if->
-+ in_ep_regs[ep->num]->dieptsiz);
-+ offset = ep->data_per_frame;
-+ } else {
-+ deptsiz.d32 =
-+ DWC_READ_REG32(&core_if->dev_if->
-+ out_ep_regs[ep->num]->doeptsiz);
-+ offset =
-+ ep->data_per_frame +
-+ (0x4 & (0x4 - (ep->data_per_frame & 0x3)));
-+ }
-+
-+ if (!deptsiz.b.xfersize) {
-+ ep->pkt_info[ep->cur_pkt].length = ep->data_per_frame;
-+ ep->pkt_info[ep->cur_pkt].offset =
-+ ep->cur_pkt_dma_addr - dma_addr;
-+ ep->pkt_info[ep->cur_pkt].status = 0;
-+ } else {
-+ ep->pkt_info[ep->cur_pkt].length = ep->data_per_frame;
-+ ep->pkt_info[ep->cur_pkt].offset =
-+ ep->cur_pkt_dma_addr - dma_addr;
-+ ep->pkt_info[ep->cur_pkt].status = -DWC_E_NO_DATA;
-+ }
-+ ep->cur_pkt_addr += offset;
-+ ep->cur_pkt_dma_addr += offset;
-+ ep->cur_pkt++;
-+}
-+
-+/**
-+ * This function sets latest iso packet information(DDMA mode)
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param dwc_ep The EP to start the transfer on.
-+ *
-+ */
-+static void set_ddma_iso_pkts_info(dwc_otg_core_if_t * core_if,
-+ dwc_ep_t * dwc_ep)
-+{
-+ dwc_otg_dev_dma_desc_t *dma_desc;
-+ dev_dma_desc_sts_t sts = {.d32 = 0 };
-+ iso_pkt_info_t *iso_packet;
-+ uint32_t data_per_desc;
-+ uint32_t offset;
-+ int i, j;
-+
-+ iso_packet = dwc_ep->pkt_info;
-+
-+ /** Reinit closed DMA Descriptors*/
-+ /** ISO OUT EP */
-+ if (dwc_ep->is_in == 0) {
-+ dma_desc =
-+ dwc_ep->iso_desc_addr +
-+ dwc_ep->desc_cnt * dwc_ep->proc_buf_num;
-+ offset = 0;
-+
-+ for (i = 0; i < dwc_ep->desc_cnt - dwc_ep->pkt_per_frm;
-+ i += dwc_ep->pkt_per_frm) {
-+ for (j = 0; j < dwc_ep->pkt_per_frm; ++j) {
-+ data_per_desc =
-+ ((j + 1) * dwc_ep->maxpacket >
-+ dwc_ep->
-+ data_per_frame) ? dwc_ep->data_per_frame -
-+ j * dwc_ep->maxpacket : dwc_ep->maxpacket;
-+ data_per_desc +=
-+ (data_per_desc % 4) ? (4 -
-+ data_per_desc %
-+ 4) : 0;
-+
-+ sts.d32 = dma_desc->status.d32;
-+
-+ /* Write status in iso_packet_decsriptor */
-+ iso_packet->status =
-+ sts.b_iso_out.rxsts +
-+ (sts.b_iso_out.bs ^ BS_DMA_DONE);
-+ if (iso_packet->status) {
-+ iso_packet->status = -DWC_E_NO_DATA;
-+ }
-+
-+ /* Received data length */
-+ if (!sts.b_iso_out.rxbytes) {
-+ iso_packet->length =
-+ data_per_desc -
-+ sts.b_iso_out.rxbytes;
-+ } else {
-+ iso_packet->length =
-+ data_per_desc -
-+ sts.b_iso_out.rxbytes + (4 -
-+ dwc_ep->data_per_frame
-+ % 4);
-+ }
-+
-+ iso_packet->offset = offset;
-+
-+ offset += data_per_desc;
-+ dma_desc++;
-+ iso_packet++;
-+ }
-+ }
-+
-+ for (j = 0; j < dwc_ep->pkt_per_frm - 1; ++j) {
-+ data_per_desc =
-+ ((j + 1) * dwc_ep->maxpacket >
-+ dwc_ep->data_per_frame) ? dwc_ep->data_per_frame -
-+ j * dwc_ep->maxpacket : dwc_ep->maxpacket;
-+ data_per_desc +=
-+ (data_per_desc % 4) ? (4 - data_per_desc % 4) : 0;
-+
-+ sts.d32 = dma_desc->status.d32;
-+
-+ /* Write status in iso_packet_decsriptor */
-+ iso_packet->status =
-+ sts.b_iso_out.rxsts +
-+ (sts.b_iso_out.bs ^ BS_DMA_DONE);
-+ if (iso_packet->status) {
-+ iso_packet->status = -DWC_E_NO_DATA;
-+ }
-+
-+ /* Received data length */
-+ iso_packet->length =
-+ dwc_ep->data_per_frame - sts.b_iso_out.rxbytes;
-+
-+ iso_packet->offset = offset;
-+
-+ offset += data_per_desc;
-+ iso_packet++;
-+ dma_desc++;
-+ }
-+
-+ sts.d32 = dma_desc->status.d32;
-+
-+ /* Write status in iso_packet_decsriptor */
-+ iso_packet->status =
-+ sts.b_iso_out.rxsts + (sts.b_iso_out.bs ^ BS_DMA_DONE);
-+ if (iso_packet->status) {
-+ iso_packet->status = -DWC_E_NO_DATA;
-+ }
-+ /* Received data length */
-+ if (!sts.b_iso_out.rxbytes) {
-+ iso_packet->length =
-+ dwc_ep->data_per_frame - sts.b_iso_out.rxbytes;
-+ } else {
-+ iso_packet->length =
-+ dwc_ep->data_per_frame - sts.b_iso_out.rxbytes +
-+ (4 - dwc_ep->data_per_frame % 4);
-+ }
-+
-+ iso_packet->offset = offset;
-+ } else {
-+/** ISO IN EP */
-+
-+ dma_desc =
-+ dwc_ep->iso_desc_addr +
-+ dwc_ep->desc_cnt * dwc_ep->proc_buf_num;
-+
-+ for (i = 0; i < dwc_ep->desc_cnt - 1; i++) {
-+ sts.d32 = dma_desc->status.d32;
-+
-+ /* Write status in iso packet descriptor */
-+ iso_packet->status =
-+ sts.b_iso_in.txsts +
-+ (sts.b_iso_in.bs ^ BS_DMA_DONE);
-+ if (iso_packet->status != 0) {
-+ iso_packet->status = -DWC_E_NO_DATA;
-+
-+ }
-+ /* Bytes has been transfered */
-+ iso_packet->length =
-+ dwc_ep->data_per_frame - sts.b_iso_in.txbytes;
-+
-+ dma_desc++;
-+ iso_packet++;
-+ }
-+
-+ sts.d32 = dma_desc->status.d32;
-+ while (sts.b_iso_in.bs == BS_DMA_BUSY) {
-+ sts.d32 = dma_desc->status.d32;
-+ }
-+
-+ /* Write status in iso packet descriptor ??? do be done with ERROR codes */
-+ iso_packet->status =
-+ sts.b_iso_in.txsts + (sts.b_iso_in.bs ^ BS_DMA_DONE);
-+ if (iso_packet->status != 0) {
-+ iso_packet->status = -DWC_E_NO_DATA;
-+ }
-+
-+ /* Bytes has been transfered */
-+ iso_packet->length =
-+ dwc_ep->data_per_frame - sts.b_iso_in.txbytes;
-+ }
-+}
-+
-+/**
-+ * This function reinitialize DMA Descriptors for Isochronous transfer
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param dwc_ep The EP to start the transfer on.
-+ *
-+ */
-+static void reinit_ddma_iso_xfer(dwc_otg_core_if_t * core_if, dwc_ep_t * dwc_ep)
-+{
-+ int i, j;
-+ dwc_otg_dev_dma_desc_t *dma_desc;
-+ dma_addr_t dma_ad;
-+ volatile uint32_t *addr;
-+ dev_dma_desc_sts_t sts = {.d32 = 0 };
-+ uint32_t data_per_desc;
-+
-+ if (dwc_ep->is_in == 0) {
-+ addr = &core_if->dev_if->out_ep_regs[dwc_ep->num]->doepctl;
-+ } else {
-+ addr = &core_if->dev_if->in_ep_regs[dwc_ep->num]->diepctl;
-+ }
-+
-+ if (dwc_ep->proc_buf_num == 0) {
-+ /** Buffer 0 descriptors setup */
-+ dma_ad = dwc_ep->dma_addr0;
-+ } else {
-+ /** Buffer 1 descriptors setup */
-+ dma_ad = dwc_ep->dma_addr1;
-+ }
-+
-+ /** Reinit closed DMA Descriptors*/
-+ /** ISO OUT EP */
-+ if (dwc_ep->is_in == 0) {
-+ dma_desc =
-+ dwc_ep->iso_desc_addr +
-+ dwc_ep->desc_cnt * dwc_ep->proc_buf_num;
-+
-+ sts.b_iso_out.bs = BS_HOST_READY;
-+ sts.b_iso_out.rxsts = 0;
-+ sts.b_iso_out.l = 0;
-+ sts.b_iso_out.sp = 0;
-+ sts.b_iso_out.ioc = 0;
-+ sts.b_iso_out.pid = 0;
-+ sts.b_iso_out.framenum = 0;
-+
-+ for (i = 0; i < dwc_ep->desc_cnt - dwc_ep->pkt_per_frm;
-+ i += dwc_ep->pkt_per_frm) {
-+ for (j = 0; j < dwc_ep->pkt_per_frm; ++j) {
-+ data_per_desc =
-+ ((j + 1) * dwc_ep->maxpacket >
-+ dwc_ep->
-+ data_per_frame) ? dwc_ep->data_per_frame -
-+ j * dwc_ep->maxpacket : dwc_ep->maxpacket;
-+ data_per_desc +=
-+ (data_per_desc % 4) ? (4 -
-+ data_per_desc %
-+ 4) : 0;
-+ sts.b_iso_out.rxbytes = data_per_desc;
-+ dma_desc->buf = dma_ad;
-+ dma_desc->status.d32 = sts.d32;
-+
-+ dma_ad += data_per_desc;
-+ dma_desc++;
-+ }
-+ }
-+
-+ for (j = 0; j < dwc_ep->pkt_per_frm - 1; ++j) {
-+
-+ data_per_desc =
-+ ((j + 1) * dwc_ep->maxpacket >
-+ dwc_ep->data_per_frame) ? dwc_ep->data_per_frame -
-+ j * dwc_ep->maxpacket : dwc_ep->maxpacket;
-+ data_per_desc +=
-+ (data_per_desc % 4) ? (4 - data_per_desc % 4) : 0;
-+ sts.b_iso_out.rxbytes = data_per_desc;
-+
-+ dma_desc->buf = dma_ad;
-+ dma_desc->status.d32 = sts.d32;
-+
-+ dma_desc++;
-+ dma_ad += data_per_desc;
-+ }
-+
-+ sts.b_iso_out.ioc = 1;
-+ sts.b_iso_out.l = dwc_ep->proc_buf_num;
-+
-+ data_per_desc =
-+ ((j + 1) * dwc_ep->maxpacket >
-+ dwc_ep->data_per_frame) ? dwc_ep->data_per_frame -
-+ j * dwc_ep->maxpacket : dwc_ep->maxpacket;
-+ data_per_desc +=
-+ (data_per_desc % 4) ? (4 - data_per_desc % 4) : 0;
-+ sts.b_iso_out.rxbytes = data_per_desc;
-+
-+ dma_desc->buf = dma_ad;
-+ dma_desc->status.d32 = sts.d32;
-+ } else {
-+/** ISO IN EP */
-+
-+ dma_desc =
-+ dwc_ep->iso_desc_addr +
-+ dwc_ep->desc_cnt * dwc_ep->proc_buf_num;
-+
-+ sts.b_iso_in.bs = BS_HOST_READY;
-+ sts.b_iso_in.txsts = 0;
-+ sts.b_iso_in.sp = 0;
-+ sts.b_iso_in.ioc = 0;
-+ sts.b_iso_in.pid = dwc_ep->pkt_per_frm;
-+ sts.b_iso_in.framenum = dwc_ep->next_frame;
-+ sts.b_iso_in.txbytes = dwc_ep->data_per_frame;
-+ sts.b_iso_in.l = 0;
-+
-+ for (i = 0; i < dwc_ep->desc_cnt - 1; i++) {
-+ dma_desc->buf = dma_ad;
-+ dma_desc->status.d32 = sts.d32;
-+
-+ sts.b_iso_in.framenum += dwc_ep->bInterval;
-+ dma_ad += dwc_ep->data_per_frame;
-+ dma_desc++;
-+ }
-+
-+ sts.b_iso_in.ioc = 1;
-+ sts.b_iso_in.l = dwc_ep->proc_buf_num;
-+
-+ dma_desc->buf = dma_ad;
-+ dma_desc->status.d32 = sts.d32;
-+
-+ dwc_ep->next_frame =
-+ sts.b_iso_in.framenum + dwc_ep->bInterval * 1;
-+ }
-+ dwc_ep->proc_buf_num = (dwc_ep->proc_buf_num ^ 1) & 0x1;
-+}
-+
-+/**
-+ * This function is to handle Iso EP transfer complete interrupt
-+ * in case Iso out packet was dropped
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param dwc_ep The EP for wihich transfer complete was asserted
-+ *
-+ */
-+static uint32_t handle_iso_out_pkt_dropped(dwc_otg_core_if_t * core_if,
-+ dwc_ep_t * dwc_ep)
-+{
-+ uint32_t dma_addr;
-+ uint32_t drp_pkt;
-+ uint32_t drp_pkt_cnt;
-+ deptsiz_data_t deptsiz = {.d32 = 0 };
-+ depctl_data_t depctl = {.d32 = 0 };
-+ int i;
-+
-+ deptsiz.d32 =
-+ DWC_READ_REG32(&core_if->dev_if->
-+ out_ep_regs[dwc_ep->num]->doeptsiz);
-+
-+ drp_pkt = dwc_ep->pkt_cnt - deptsiz.b.pktcnt;
-+ drp_pkt_cnt = dwc_ep->pkt_per_frm - (drp_pkt % dwc_ep->pkt_per_frm);
-+
-+ /* Setting dropped packets status */
-+ for (i = 0; i < drp_pkt_cnt; ++i) {
-+ dwc_ep->pkt_info[drp_pkt].status = -DWC_E_NO_DATA;
-+ drp_pkt++;
-+ deptsiz.b.pktcnt--;
-+ }
-+
-+ if (deptsiz.b.pktcnt > 0) {
-+ deptsiz.b.xfersize =
-+ dwc_ep->xfer_len - (dwc_ep->pkt_cnt -
-+ deptsiz.b.pktcnt) * dwc_ep->maxpacket;
-+ } else {
-+ deptsiz.b.xfersize = 0;
-+ deptsiz.b.pktcnt = 0;
-+ }
-+
-+ DWC_WRITE_REG32(&core_if->dev_if->out_ep_regs[dwc_ep->num]->doeptsiz,
-+ deptsiz.d32);
-+
-+ if (deptsiz.b.pktcnt > 0) {
-+ if (dwc_ep->proc_buf_num) {
-+ dma_addr =
-+ dwc_ep->dma_addr1 + dwc_ep->xfer_len -
-+ deptsiz.b.xfersize;
-+ } else {
-+ dma_addr =
-+ dwc_ep->dma_addr0 + dwc_ep->xfer_len -
-+ deptsiz.b.xfersize;;
-+ }
-+
-+ DWC_WRITE_REG32(&core_if->dev_if->
-+ out_ep_regs[dwc_ep->num]->doepdma, dma_addr);
-+
-+ /** Re-enable endpoint, clear nak */
-+ depctl.d32 = 0;
-+ depctl.b.epena = 1;
-+ depctl.b.cnak = 1;
-+
-+ DWC_MODIFY_REG32(&core_if->dev_if->
-+ out_ep_regs[dwc_ep->num]->doepctl, depctl.d32,
-+ depctl.d32);
-+ return 0;
-+ } else {
-+ return 1;
-+ }
-+}
-+
-+/**
-+ * This function sets iso packets information(PTI mode)
-+ *
-+ * @param core_if Programming view of DWC_otg controller.
-+ * @param ep The EP to start the transfer on.
-+ *
-+ */
-+static uint32_t set_iso_pkts_info(dwc_otg_core_if_t * core_if, dwc_ep_t * ep)
-+{
-+ int i, j;
-+ dma_addr_t dma_ad;
-+ iso_pkt_info_t *packet_info = ep->pkt_info;
-+ uint32_t offset;
-+ uint32_t frame_data;
-+ deptsiz_data_t deptsiz;
-+
-+ if (ep->proc_buf_num == 0) {
-+ /** Buffer 0 descriptors setup */
-+ dma_ad = ep->dma_addr0;
-+ } else {
-+ /** Buffer 1 descriptors setup */
-+ dma_ad = ep->dma_addr1;
-+ }
-+
-+ if (ep->is_in) {
-+ deptsiz.d32 =
-+ DWC_READ_REG32(&core_if->dev_if->in_ep_regs[ep->num]->
-+ dieptsiz);
-+ } else {
-+ deptsiz.d32 =
-+ DWC_READ_REG32(&core_if->dev_if->out_ep_regs[ep->num]->
-+ doeptsiz);
-+ }
-+
-+ if (!deptsiz.b.xfersize) {
-+ offset = 0;
-+ for (i = 0; i < ep->pkt_cnt; i += ep->pkt_per_frm) {
-+ frame_data = ep->data_per_frame;
-+ for (j = 0; j < ep->pkt_per_frm; ++j) {
-+
-+ /* Packet status - is not set as initially
-+ * it is set to 0 and if packet was sent
-+ successfully, status field will remain 0*/
-+
-+ /* Bytes has been transfered */
-+ packet_info->length =
-+ (ep->maxpacket <
-+ frame_data) ? ep->maxpacket : frame_data;
-+
-+ /* Received packet offset */
-+ packet_info->offset = offset;
-+ offset += packet_info->length;
-+ frame_data -= packet_info->length;
-+
-+ packet_info++;
-+ }
-+ }
-+ return 1;
-+ } else {
-+ /* This is a workaround for in case of Transfer Complete with
-+ * PktDrpSts interrupts merging - in this case Transfer complete
-+ * interrupt for Isoc Out Endpoint is asserted without PktDrpSts
-+ * set and with DOEPTSIZ register non zero. Investigations showed,
-+ * that this happens when Out packet is dropped, but because of
-+ * interrupts merging during first interrupt handling PktDrpSts
-+ * bit is cleared and for next merged interrupts it is not reset.
-+ * In this case SW hadles the interrupt as if PktDrpSts bit is set.
-+ */
-+ if (ep->is_in) {
-+ return 1;
-+ } else {
-+ return handle_iso_out_pkt_dropped(core_if, ep);
-+ }
-+ }
-+}
-+
-+/**
-+ * This function is to handle Iso EP transfer complete interrupt
-+ *
-+ * @param pcd The PCD
-+ * @param ep The EP for which transfer complete was asserted
-+ *
-+ */
-+static void complete_iso_ep(dwc_otg_pcd_t * pcd, dwc_otg_pcd_ep_t * ep)
-+{
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(ep->pcd);
-+ dwc_ep_t *dwc_ep = &ep->dwc_ep;
-+ uint8_t is_last = 0;
-+
-+ if (ep->dwc_ep.next_frame == 0xffffffff) {
-+ DWC_WARN("Next frame is not set!\n");
-+ return;
-+ }
-+
-+ if (core_if->dma_enable) {
-+ if (core_if->dma_desc_enable) {
-+ set_ddma_iso_pkts_info(core_if, dwc_ep);
-+ reinit_ddma_iso_xfer(core_if, dwc_ep);
-+ is_last = 1;
-+ } else {
-+ if (core_if->pti_enh_enable) {
-+ if (set_iso_pkts_info(core_if, dwc_ep)) {
-+ dwc_ep->proc_buf_num =
-+ (dwc_ep->proc_buf_num ^ 1) & 0x1;
-+ dwc_otg_iso_ep_start_buf_transfer
-+ (core_if, dwc_ep);
-+ is_last = 1;
-+ }
-+ } else {
-+ set_current_pkt_info(core_if, dwc_ep);
-+ if (dwc_ep->cur_pkt >= dwc_ep->pkt_cnt) {
-+ is_last = 1;
-+ dwc_ep->cur_pkt = 0;
-+ dwc_ep->proc_buf_num =
-+ (dwc_ep->proc_buf_num ^ 1) & 0x1;
-+ if (dwc_ep->proc_buf_num) {
-+ dwc_ep->cur_pkt_addr =
-+ dwc_ep->xfer_buff1;
-+ dwc_ep->cur_pkt_dma_addr =
-+ dwc_ep->dma_addr1;
-+ } else {
-+ dwc_ep->cur_pkt_addr =
-+ dwc_ep->xfer_buff0;
-+ dwc_ep->cur_pkt_dma_addr =
-+ dwc_ep->dma_addr0;
-+ }
-+
-+ }
-+ dwc_otg_iso_ep_start_frm_transfer(core_if,
-+ dwc_ep);
-+ }
-+ }
-+ } else {
-+ set_current_pkt_info(core_if, dwc_ep);
-+ if (dwc_ep->cur_pkt >= dwc_ep->pkt_cnt) {
-+ is_last = 1;
-+ dwc_ep->cur_pkt = 0;
-+ dwc_ep->proc_buf_num = (dwc_ep->proc_buf_num ^ 1) & 0x1;
-+ if (dwc_ep->proc_buf_num) {
-+ dwc_ep->cur_pkt_addr = dwc_ep->xfer_buff1;
-+ dwc_ep->cur_pkt_dma_addr = dwc_ep->dma_addr1;
-+ } else {
-+ dwc_ep->cur_pkt_addr = dwc_ep->xfer_buff0;
-+ dwc_ep->cur_pkt_dma_addr = dwc_ep->dma_addr0;
-+ }
-+
-+ }
-+ dwc_otg_iso_ep_start_frm_transfer(core_if, dwc_ep);
-+ }
-+ if (is_last)
-+ dwc_otg_iso_buffer_done(pcd, ep, ep->iso_req_handle);
-+}
-+#endif /* DWC_EN_ISOC */
-+
-+/**
-+ * This function handle BNA interrupt for Non Isochronous EPs
-+ *
-+ */
-+static void dwc_otg_pcd_handle_noniso_bna(dwc_otg_pcd_ep_t * ep)
-+{
-+ dwc_ep_t *dwc_ep = &ep->dwc_ep;
-+ volatile uint32_t *addr;
-+ depctl_data_t depctl = {.d32 = 0 };
-+ dwc_otg_pcd_t *pcd = ep->pcd;
-+ dwc_otg_dev_dma_desc_t *dma_desc;
-+ dev_dma_desc_sts_t sts = {.d32 = 0 };
-+ dwc_otg_core_if_t *core_if = ep->pcd->core_if;
-+ int i, start;
-+
-+ if (!dwc_ep->desc_cnt)
-+ DWC_WARN("Ep%d %s Descriptor count = %d \n", dwc_ep->num,
-+ (dwc_ep->is_in ? "IN" : "OUT"), dwc_ep->desc_cnt);
-+
-+ if (core_if->core_params->cont_on_bna && !dwc_ep->is_in
-+ && dwc_ep->type != DWC_OTG_EP_TYPE_CONTROL) {
-+ uint32_t doepdma;
-+ dwc_otg_dev_out_ep_regs_t *out_regs =
-+ core_if->dev_if->out_ep_regs[dwc_ep->num];
-+ doepdma = DWC_READ_REG32(&(out_regs->doepdma));
-+ start = (doepdma - dwc_ep->dma_desc_addr)/sizeof(dwc_otg_dev_dma_desc_t);
-+ dma_desc = &(dwc_ep->desc_addr[start]);
-+ } else {
-+ start = 0;
-+ dma_desc = dwc_ep->desc_addr;
-+ }
-+
-+
-+ for (i = start; i < dwc_ep->desc_cnt; ++i, ++dma_desc) {
-+ sts.d32 = dma_desc->status.d32;
-+ sts.b.bs = BS_HOST_READY;
-+ dma_desc->status.d32 = sts.d32;
-+ }
-+
-+ if (dwc_ep->is_in == 0) {
-+ addr =
-+ &GET_CORE_IF(pcd)->dev_if->out_ep_regs[dwc_ep->num]->
-+ doepctl;
-+ } else {
-+ addr =
-+ &GET_CORE_IF(pcd)->dev_if->in_ep_regs[dwc_ep->num]->diepctl;
-+ }
-+ depctl.b.epena = 1;
-+ depctl.b.cnak = 1;
-+ DWC_MODIFY_REG32(addr, 0, depctl.d32);
-+}
-+
-+/**
-+ * This function handles EP0 Control transfers.
-+ *
-+ * The state of the control transfers are tracked in
-+ * <code>ep0state</code>.
-+ */
-+static void handle_ep0(dwc_otg_pcd_t * pcd)
-+{
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+ dwc_otg_pcd_ep_t *ep0 = &pcd->ep0;
-+ dev_dma_desc_sts_t desc_sts;
-+ deptsiz0_data_t deptsiz;
-+ uint32_t byte_count;
-+
-+#ifdef DEBUG_EP0
-+ DWC_DEBUGPL(DBG_PCDV, "%s()\n", __func__);
-+ print_ep0_state(pcd);
-+#endif
-+
-+// DWC_PRINTF("HANDLE EP0\n");
-+
-+ switch (pcd->ep0state) {
-+ case EP0_DISCONNECT:
-+ break;
-+
-+ case EP0_IDLE:
-+ pcd->request_config = 0;
-+
-+ pcd_setup(pcd);
-+ break;
-+
-+ case EP0_IN_DATA_PHASE:
-+#ifdef DEBUG_EP0
-+ DWC_DEBUGPL(DBG_PCD, "DATA_IN EP%d-%s: type=%d, mps=%d\n",
-+ ep0->dwc_ep.num, (ep0->dwc_ep.is_in ? "IN" : "OUT"),
-+ ep0->dwc_ep.type, ep0->dwc_ep.maxpacket);
-+#endif
-+
-+ if (core_if->dma_enable != 0) {
-+ /*
-+ * For EP0 we can only program 1 packet at a time so we
-+ * need to do the make calculations after each complete.
-+ * Call write_packet to make the calculations, as in
-+ * slave mode, and use those values to determine if we
-+ * can complete.
-+ */
-+ if (core_if->dma_desc_enable == 0) {
-+ deptsiz.d32 =
-+ DWC_READ_REG32(&core_if->
-+ dev_if->in_ep_regs[0]->
-+ dieptsiz);
-+ byte_count =
-+ ep0->dwc_ep.xfer_len - deptsiz.b.xfersize;
-+ } else {
-+ desc_sts =
-+ core_if->dev_if->in_desc_addr->status;
-+ byte_count =
-+ ep0->dwc_ep.xfer_len - desc_sts.b.bytes;
-+ }
-+ ep0->dwc_ep.xfer_count += byte_count;
-+ ep0->dwc_ep.xfer_buff += byte_count;
-+ ep0->dwc_ep.dma_addr += byte_count;
-+ }
-+ if (ep0->dwc_ep.xfer_count < ep0->dwc_ep.total_len) {
-+ dwc_otg_ep0_continue_transfer(GET_CORE_IF(pcd),
-+ &ep0->dwc_ep);
-+ DWC_DEBUGPL(DBG_PCD, "CONTINUE TRANSFER\n");
-+ } else if (ep0->dwc_ep.sent_zlp) {
-+ dwc_otg_ep0_continue_transfer(GET_CORE_IF(pcd),
-+ &ep0->dwc_ep);
-+ ep0->dwc_ep.sent_zlp = 0;
-+ DWC_DEBUGPL(DBG_PCD, "CONTINUE TRANSFER sent zlp\n");
-+ } else {
-+ ep0_complete_request(ep0);
-+ DWC_DEBUGPL(DBG_PCD, "COMPLETE TRANSFER\n");
-+ }
-+ break;
-+ case EP0_OUT_DATA_PHASE:
-+#ifdef DEBUG_EP0
-+ DWC_DEBUGPL(DBG_PCD, "DATA_OUT EP%d-%s: type=%d, mps=%d\n",
-+ ep0->dwc_ep.num, (ep0->dwc_ep.is_in ? "IN" : "OUT"),
-+ ep0->dwc_ep.type, ep0->dwc_ep.maxpacket);
-+#endif
-+ if (core_if->dma_enable != 0) {
-+ if (core_if->dma_desc_enable == 0) {
-+ deptsiz.d32 =
-+ DWC_READ_REG32(&core_if->
-+ dev_if->out_ep_regs[0]->
-+ doeptsiz);
-+ byte_count =
-+ ep0->dwc_ep.maxpacket - deptsiz.b.xfersize;
-+ } else {
-+ desc_sts =
-+ core_if->dev_if->out_desc_addr->status;
-+ byte_count =
-+ ep0->dwc_ep.maxpacket - desc_sts.b.bytes;
-+ }
-+ ep0->dwc_ep.xfer_count += byte_count;
-+ ep0->dwc_ep.xfer_buff += byte_count;
-+ ep0->dwc_ep.dma_addr += byte_count;
-+ }
-+ if (ep0->dwc_ep.xfer_count < ep0->dwc_ep.total_len) {
-+ dwc_otg_ep0_continue_transfer(GET_CORE_IF(pcd),
-+ &ep0->dwc_ep);
-+ DWC_DEBUGPL(DBG_PCD, "CONTINUE TRANSFER\n");
-+ } else if (ep0->dwc_ep.sent_zlp) {
-+ dwc_otg_ep0_continue_transfer(GET_CORE_IF(pcd),
-+ &ep0->dwc_ep);
-+ ep0->dwc_ep.sent_zlp = 0;
-+ DWC_DEBUGPL(DBG_PCD, "CONTINUE TRANSFER sent zlp\n");
-+ } else {
-+ ep0_complete_request(ep0);
-+ DWC_DEBUGPL(DBG_PCD, "COMPLETE TRANSFER\n");
-+ }
-+ break;
-+
-+ case EP0_IN_STATUS_PHASE:
-+ case EP0_OUT_STATUS_PHASE:
-+ DWC_DEBUGPL(DBG_PCD, "CASE: EP0_STATUS\n");
-+ ep0_complete_request(ep0);
-+ pcd->ep0state = EP0_IDLE;
-+ ep0->stopped = 1;
-+ ep0->dwc_ep.is_in = 0; /* OUT for next SETUP */
-+
-+ /* Prepare for more SETUP Packets */
-+ if (core_if->dma_enable) {
-+ ep0_out_start(core_if, pcd);
-+ }
-+ break;
-+
-+ case EP0_STALL:
-+ DWC_ERROR("EP0 STALLed, should not get here pcd_setup()\n");
-+ break;
-+ }
-+#ifdef DEBUG_EP0
-+ print_ep0_state(pcd);
-+#endif
-+}
-+
-+/**
-+ * Restart transfer
-+ */
-+static void restart_transfer(dwc_otg_pcd_t * pcd, const uint32_t epnum)
-+{
-+ dwc_otg_core_if_t *core_if;
-+ dwc_otg_dev_if_t *dev_if;
-+ deptsiz_data_t dieptsiz = {.d32 = 0 };
-+ dwc_otg_pcd_ep_t *ep;
-+
-+ ep = get_in_ep(pcd, epnum);
-+
-+#ifdef DWC_EN_ISOC
-+ if (ep->dwc_ep.type == DWC_OTG_EP_TYPE_ISOC) {
-+ return;
-+ }
-+#endif /* DWC_EN_ISOC */
-+
-+ core_if = GET_CORE_IF(pcd);
-+ dev_if = core_if->dev_if;
-+
-+ dieptsiz.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[epnum]->dieptsiz);
-+
-+ DWC_DEBUGPL(DBG_PCD, "xfer_buff=%p xfer_count=%0x xfer_len=%0x"
-+ " stopped=%d\n", ep->dwc_ep.xfer_buff,
-+ ep->dwc_ep.xfer_count, ep->dwc_ep.xfer_len, ep->stopped);
-+ /*
-+ * If xfersize is 0 and pktcnt in not 0, resend the last packet.
-+ */
-+ if (dieptsiz.b.pktcnt && dieptsiz.b.xfersize == 0 &&
-+ ep->dwc_ep.start_xfer_buff != 0) {
-+ if (ep->dwc_ep.total_len <= ep->dwc_ep.maxpacket) {
-+ ep->dwc_ep.xfer_count = 0;
-+ ep->dwc_ep.xfer_buff = ep->dwc_ep.start_xfer_buff;
-+ ep->dwc_ep.xfer_len = ep->dwc_ep.xfer_count;
-+ } else {
-+ ep->dwc_ep.xfer_count -= ep->dwc_ep.maxpacket;
-+ /* convert packet size to dwords. */
-+ ep->dwc_ep.xfer_buff -= ep->dwc_ep.maxpacket;
-+ ep->dwc_ep.xfer_len = ep->dwc_ep.xfer_count;
-+ }
-+ ep->stopped = 0;
-+ DWC_DEBUGPL(DBG_PCD, "xfer_buff=%p xfer_count=%0x "
-+ "xfer_len=%0x stopped=%d\n",
-+ ep->dwc_ep.xfer_buff,
-+ ep->dwc_ep.xfer_count, ep->dwc_ep.xfer_len,
-+ ep->stopped);
-+ if (epnum == 0) {
-+ dwc_otg_ep0_start_transfer(core_if, &ep->dwc_ep);
-+ } else {
-+ dwc_otg_ep_start_transfer(core_if, &ep->dwc_ep);
-+ }
-+ }
-+}
-+
-+/*
-+ * This function create new nextep sequnce based on Learn Queue.
-+ *
-+ * @param core_if Programming view of DWC_otg controller
-+ */
-+void predict_nextep_seq( dwc_otg_core_if_t * core_if)
-+{
-+ dwc_otg_device_global_regs_t *dev_global_regs =
-+ core_if->dev_if->dev_global_regs;
-+ const uint32_t TOKEN_Q_DEPTH = core_if->hwcfg2.b.dev_token_q_depth;
-+ /* Number of Token Queue Registers */
-+ const int DTKNQ_REG_CNT = (TOKEN_Q_DEPTH + 7) / 8;
-+ dtknq1_data_t dtknqr1;
-+ uint32_t in_tkn_epnums[4];
-+ uint8_t seqnum[MAX_EPS_CHANNELS];
-+ uint8_t intkn_seq[TOKEN_Q_DEPTH];
-+ grstctl_t resetctl = {.d32 = 0 };
-+ uint8_t temp;
-+ int ndx = 0;
-+ int start = 0;
-+ int end = 0;
-+ int sort_done = 0;
-+ int i = 0;
-+ volatile uint32_t *addr = &dev_global_regs->dtknqr1;
-+
-+
-+ DWC_DEBUGPL(DBG_PCD,"dev_token_q_depth=%d\n",TOKEN_Q_DEPTH);
-+
-+ /* Read the DTKNQ Registers */
-+ for (i = 0; i < DTKNQ_REG_CNT; i++) {
-+ in_tkn_epnums[i] = DWC_READ_REG32(addr);
-+ DWC_DEBUGPL(DBG_PCDV, "DTKNQR%d=0x%08x\n", i + 1,
-+ in_tkn_epnums[i]);
-+ if (addr == &dev_global_regs->dvbusdis) {
-+ addr = &dev_global_regs->dtknqr3_dthrctl;
-+ } else {
-+ ++addr;
-+ }
-+
-+ }
-+
-+ /* Copy the DTKNQR1 data to the bit field. */
-+ dtknqr1.d32 = in_tkn_epnums[0];
-+ if (dtknqr1.b.wrap_bit) {
-+ ndx = dtknqr1.b.intknwptr;
-+ end = ndx -1;
-+ if (end < 0)
-+ end = TOKEN_Q_DEPTH -1;
-+ } else {
-+ ndx = 0;
-+ end = dtknqr1.b.intknwptr -1;
-+ if (end < 0)
-+ end = 0;
-+ }
-+ start = ndx;
-+
-+ /* Fill seqnum[] by initial values: EP number + 31 */
-+ for (i=0; i <= core_if->dev_if->num_in_eps; i++) {
-+ seqnum[i] = i +31;
-+ }
-+
-+ /* Fill intkn_seq[] from in_tkn_epnums[0] */
-+ for (i=0; i < 6; i++)
-+ intkn_seq[i] = (in_tkn_epnums[0] >> ((7-i) * 4)) & 0xf;
-+
-+ if (TOKEN_Q_DEPTH > 6) {
-+ /* Fill intkn_seq[] from in_tkn_epnums[1] */
-+ for (i=6; i < 14; i++)
-+ intkn_seq[i] =
-+ (in_tkn_epnums[1] >> ((7 - (i - 6)) * 4)) & 0xf;
-+ }
-+
-+ if (TOKEN_Q_DEPTH > 14) {
-+ /* Fill intkn_seq[] from in_tkn_epnums[1] */
-+ for (i=14; i < 22; i++)
-+ intkn_seq[i] =
-+ (in_tkn_epnums[2] >> ((7 - (i - 14)) * 4)) & 0xf;
-+ }
-+
-+ if (TOKEN_Q_DEPTH > 22) {
-+ /* Fill intkn_seq[] from in_tkn_epnums[1] */
-+ for (i=22; i < 30; i++)
-+ intkn_seq[i] =
-+ (in_tkn_epnums[3] >> ((7 - (i - 22)) * 4)) & 0xf;
-+ }
-+
-+ DWC_DEBUGPL(DBG_PCDV, "%s start=%d end=%d intkn_seq[]:\n", __func__,
-+ start, end);
-+ for (i=0; i<TOKEN_Q_DEPTH; i++)
-+ DWC_DEBUGPL(DBG_PCDV,"%d\n", intkn_seq[i]);
-+
-+ /* Update seqnum based on intkn_seq[] */
-+ i = 0;
-+ do {
-+ seqnum[intkn_seq[ndx]] = i;
-+ ndx++;
-+ i++;
-+ if (ndx == TOKEN_Q_DEPTH)
-+ ndx = 0;
-+ } while ( i < TOKEN_Q_DEPTH );
-+
-+ /* Mark non active EP's in seqnum[] by 0xff */
-+ for (i=0; i<=core_if->dev_if->num_in_eps; i++) {
-+ if (core_if->nextep_seq[i] == 0xff )
-+ seqnum[i] = 0xff;
-+ }
-+
-+ /* Sort seqnum[] */
-+ sort_done = 0;
-+ while (!sort_done) {
-+ sort_done = 1;
-+ for (i=0; i<core_if->dev_if->num_in_eps; i++) {
-+ if (seqnum[i] > seqnum[i+1]) {
-+ temp = seqnum[i];
-+ seqnum[i] = seqnum[i+1];
-+ seqnum[i+1] = temp;
-+ sort_done = 0;
-+ }
-+ }
-+ }
-+
-+ ndx = start + seqnum[0];
-+ if (ndx >= TOKEN_Q_DEPTH)
-+ ndx = ndx % TOKEN_Q_DEPTH;
-+ core_if->first_in_nextep_seq = intkn_seq[ndx];
-+
-+ /* Update seqnum[] by EP numbers */
-+ for (i=0; i<=core_if->dev_if->num_in_eps; i++) {
-+ ndx = start + i;
-+ if (seqnum[i] < 31) {
-+ ndx = start + seqnum[i];
-+ if (ndx >= TOKEN_Q_DEPTH)
-+ ndx = ndx % TOKEN_Q_DEPTH;
-+ seqnum[i] = intkn_seq[ndx];
-+ } else {
-+ if (seqnum[i] < 0xff) {
-+ seqnum[i] = seqnum[i] - 31;
-+ } else {
-+ break;
-+ }
-+ }
-+ }
-+
-+ /* Update nextep_seq[] based on seqnum[] */
-+ for (i=0; i<core_if->dev_if->num_in_eps; i++) {
-+ if (seqnum[i] != 0xff) {
-+ if (seqnum[i+1] != 0xff) {
-+ core_if->nextep_seq[seqnum[i]] = seqnum[i+1];
-+ } else {
-+ core_if->nextep_seq[seqnum[i]] = core_if->first_in_nextep_seq;
-+ break;
-+ }
-+ } else {
-+ break;
-+ }
-+ }
-+
-+ DWC_DEBUGPL(DBG_PCDV, "%s first_in_nextep_seq= %2d; nextep_seq[]:\n",
-+ __func__, core_if->first_in_nextep_seq);
-+ for (i=0; i <= core_if->dev_if->num_in_eps; i++) {
-+ DWC_DEBUGPL(DBG_PCDV,"%2d\n", core_if->nextep_seq[i]);
-+ }
-+
-+ /* Flush the Learning Queue */
-+ resetctl.d32 = DWC_READ_REG32(&core_if->core_global_regs->grstctl);
-+ resetctl.b.intknqflsh = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->grstctl, resetctl.d32);
-+
-+
-+}
-+
-+/**
-+ * handle the IN EP disable interrupt.
-+ */
-+static inline void handle_in_ep_disable_intr(dwc_otg_pcd_t * pcd,
-+ const uint32_t epnum)
-+{
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+ dwc_otg_dev_if_t *dev_if = core_if->dev_if;
-+ deptsiz_data_t dieptsiz = {.d32 = 0 };
-+ dctl_data_t dctl = {.d32 = 0 };
-+ dwc_otg_pcd_ep_t *ep;
-+ dwc_ep_t *dwc_ep;
-+ gintmsk_data_t gintmsk_data;
-+ depctl_data_t depctl;
-+ uint32_t diepdma;
-+ uint32_t remain_to_transfer = 0;
-+ uint8_t i;
-+ uint32_t xfer_size;
-+
-+ ep = get_in_ep(pcd, epnum);
-+ dwc_ep = &ep->dwc_ep;
-+
-+ if (dwc_ep->type == DWC_OTG_EP_TYPE_ISOC) {
-+ dwc_otg_flush_tx_fifo(core_if, dwc_ep->tx_fifo_num);
-+ complete_ep(ep);
-+ return;
-+ }
-+
-+ DWC_DEBUGPL(DBG_PCD, "diepctl%d=%0x\n", epnum,
-+ DWC_READ_REG32(&dev_if->in_ep_regs[epnum]->diepctl));
-+ dieptsiz.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[epnum]->dieptsiz);
-+ depctl.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[epnum]->diepctl);
-+
-+ DWC_DEBUGPL(DBG_ANY, "pktcnt=%d size=%d\n",
-+ dieptsiz.b.pktcnt, dieptsiz.b.xfersize);
-+
-+ if ((core_if->start_predict == 0) || (depctl.b.eptype & 1)) {
-+ if (ep->stopped) {
-+ if (core_if->en_multiple_tx_fifo)
-+ /* Flush the Tx FIFO */
-+ dwc_otg_flush_tx_fifo(core_if, dwc_ep->tx_fifo_num);
-+ /* Clear the Global IN NP NAK */
-+ dctl.d32 = 0;
-+ dctl.b.cgnpinnak = 1;
-+ DWC_MODIFY_REG32(&dev_if->dev_global_regs->dctl, dctl.d32, dctl.d32);
-+ /* Restart the transaction */
-+ if (dieptsiz.b.pktcnt != 0 || dieptsiz.b.xfersize != 0) {
-+ restart_transfer(pcd, epnum);
-+ }
-+ } else {
-+ /* Restart the transaction */
-+ if (dieptsiz.b.pktcnt != 0 || dieptsiz.b.xfersize != 0) {
-+ restart_transfer(pcd, epnum);
-+ }
-+ DWC_DEBUGPL(DBG_ANY, "STOPPED!!!\n");
-+ }
-+ return;
-+ }
-+
-+ if (core_if->start_predict > 2) { // NP IN EP
-+ core_if->start_predict--;
-+ return;
-+ }
-+
-+ core_if->start_predict--;
-+
-+ if (core_if->start_predict == 1) { // All NP IN Ep's disabled now
-+
-+ predict_nextep_seq(core_if);
-+
-+ /* Update all active IN EP's NextEP field based of nextep_seq[] */
-+ for ( i = 0; i <= core_if->dev_if->num_in_eps; i++) {
-+ depctl.d32 =
-+ DWC_READ_REG32(&dev_if->in_ep_regs[i]->diepctl);
-+ if (core_if->nextep_seq[i] != 0xff) { // Active NP IN EP
-+ depctl.b.nextep = core_if->nextep_seq[i];
-+ DWC_WRITE_REG32(&dev_if->in_ep_regs[i]->diepctl, depctl.d32);
-+ }
-+ }
-+ /* Flush Shared NP TxFIFO */
-+ dwc_otg_flush_tx_fifo(core_if, 0);
-+ /* Rewind buffers */
-+ if (!core_if->dma_desc_enable) {
-+ i = core_if->first_in_nextep_seq;
-+ do {
-+ ep = get_in_ep(pcd, i);
-+ dieptsiz.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[i]->dieptsiz);
-+ xfer_size = ep->dwc_ep.total_len - ep->dwc_ep.xfer_count;
-+ if (xfer_size > ep->dwc_ep.maxxfer)
-+ xfer_size = ep->dwc_ep.maxxfer;
-+ depctl.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[i]->diepctl);
-+ if (dieptsiz.b.pktcnt != 0) {
-+ if (xfer_size == 0) {
-+ remain_to_transfer = 0;
-+ } else {
-+ if ((xfer_size % ep->dwc_ep.maxpacket) == 0) {
-+ remain_to_transfer =
-+ dieptsiz.b.pktcnt * ep->dwc_ep.maxpacket;
-+ } else {
-+ remain_to_transfer = ((dieptsiz.b.pktcnt -1) * ep->dwc_ep.maxpacket)
-+ + (xfer_size % ep->dwc_ep.maxpacket);
-+ }
-+ }
-+ diepdma = DWC_READ_REG32(&dev_if->in_ep_regs[i]->diepdma);
-+ dieptsiz.b.xfersize = remain_to_transfer;
-+ DWC_WRITE_REG32(&dev_if->in_ep_regs[i]->dieptsiz, dieptsiz.d32);
-+ diepdma = ep->dwc_ep.dma_addr + (xfer_size - remain_to_transfer);
-+ DWC_WRITE_REG32(&dev_if->in_ep_regs[i]->diepdma, diepdma);
-+ }
-+ i = core_if->nextep_seq[i];
-+ } while (i != core_if->first_in_nextep_seq);
-+ } else { // dma_desc_enable
-+ DWC_PRINTF("%s Learning Queue not supported in DDMA\n", __func__);
-+ }
-+
-+ /* Restart transfers in predicted sequences */
-+ i = core_if->first_in_nextep_seq;
-+ do {
-+ dieptsiz.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[i]->dieptsiz);
-+ depctl.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[i]->diepctl);
-+ if (dieptsiz.b.pktcnt != 0) {
-+ depctl.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[i]->diepctl);
-+ depctl.b.epena = 1;
-+ depctl.b.cnak = 1;
-+ DWC_WRITE_REG32(&dev_if->in_ep_regs[i]->diepctl, depctl.d32);
-+ }
-+ i = core_if->nextep_seq[i];
-+ } while (i != core_if->first_in_nextep_seq);
-+
-+ /* Clear the global non-periodic IN NAK handshake */
-+ dctl.d32 = 0;
-+ dctl.b.cgnpinnak = 1;
-+ DWC_MODIFY_REG32(&dev_if->dev_global_regs->dctl, dctl.d32, dctl.d32);
-+
-+ /* Unmask EP Mismatch interrupt */
-+ gintmsk_data.d32 = 0;
-+ gintmsk_data.b.epmismatch = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gintmsk, 0, gintmsk_data.d32);
-+
-+ core_if->start_predict = 0;
-+
-+ }
-+}
-+
-+/**
-+ * Handler for the IN EP timeout handshake interrupt.
-+ */
-+static inline void handle_in_ep_timeout_intr(dwc_otg_pcd_t * pcd,
-+ const uint32_t epnum)
-+{
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+ dwc_otg_dev_if_t *dev_if = core_if->dev_if;
-+
-+#ifdef DEBUG
-+ deptsiz_data_t dieptsiz = {.d32 = 0 };
-+ uint32_t num = 0;
-+#endif
-+ dctl_data_t dctl = {.d32 = 0 };
-+ dwc_otg_pcd_ep_t *ep;
-+
-+ gintmsk_data_t intr_mask = {.d32 = 0 };
-+
-+ ep = get_in_ep(pcd, epnum);
-+
-+ /* Disable the NP Tx Fifo Empty Interrrupt */
-+ if (!core_if->dma_enable) {
-+ intr_mask.b.nptxfempty = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gintmsk,
-+ intr_mask.d32, 0);
-+ }
-+ /** @todo NGS Check EP type.
-+ * Implement for Periodic EPs */
-+ /*
-+ * Non-periodic EP
-+ */
-+ /* Enable the Global IN NAK Effective Interrupt */
-+ intr_mask.b.ginnakeff = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gintmsk, 0, intr_mask.d32);
-+
-+ /* Set Global IN NAK */
-+ dctl.b.sgnpinnak = 1;
-+ DWC_MODIFY_REG32(&dev_if->dev_global_regs->dctl, dctl.d32, dctl.d32);
-+
-+ ep->stopped = 1;
-+
-+#ifdef DEBUG
-+ dieptsiz.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[num]->dieptsiz);
-+ DWC_DEBUGPL(DBG_ANY, "pktcnt=%d size=%d\n",
-+ dieptsiz.b.pktcnt, dieptsiz.b.xfersize);
-+#endif
-+
-+#ifdef DISABLE_PERIODIC_EP
-+ /*
-+ * Set the NAK bit for this EP to
-+ * start the disable process.
-+ */
-+ diepctl.d32 = 0;
-+ diepctl.b.snak = 1;
-+ DWC_MODIFY_REG32(&dev_if->in_ep_regs[num]->diepctl, diepctl.d32,
-+ diepctl.d32);
-+ ep->disabling = 1;
-+ ep->stopped = 1;
-+#endif
-+}
-+
-+/**
-+ * Handler for the IN EP NAK interrupt.
-+ */
-+static inline int32_t handle_in_ep_nak_intr(dwc_otg_pcd_t * pcd,
-+ const uint32_t epnum)
-+{
-+ /** @todo implement ISR */
-+ dwc_otg_core_if_t *core_if;
-+ diepmsk_data_t intr_mask = {.d32 = 0 };
-+
-+ DWC_PRINTF("INTERRUPT Handler not implemented for %s\n", "IN EP NAK");
-+ core_if = GET_CORE_IF(pcd);
-+ intr_mask.b.nak = 1;
-+
-+ if (core_if->multiproc_int_enable) {
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->
-+ diepeachintmsk[epnum], intr_mask.d32, 0);
-+ } else {
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->diepmsk,
-+ intr_mask.d32, 0);
-+ }
-+
-+ return 1;
-+}
-+
-+/**
-+ * Handler for the OUT EP Babble interrupt.
-+ */
-+static inline int32_t handle_out_ep_babble_intr(dwc_otg_pcd_t * pcd,
-+ const uint32_t epnum)
-+{
-+ /** @todo implement ISR */
-+ dwc_otg_core_if_t *core_if;
-+ doepmsk_data_t intr_mask = {.d32 = 0 };
-+
-+ DWC_PRINTF("INTERRUPT Handler not implemented for %s\n",
-+ "OUT EP Babble");
-+ core_if = GET_CORE_IF(pcd);
-+ intr_mask.b.babble = 1;
-+
-+ if (core_if->multiproc_int_enable) {
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->
-+ doepeachintmsk[epnum], intr_mask.d32, 0);
-+ } else {
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->doepmsk,
-+ intr_mask.d32, 0);
-+ }
-+
-+ return 1;
-+}
-+
-+/**
-+ * Handler for the OUT EP NAK interrupt.
-+ */
-+static inline int32_t handle_out_ep_nak_intr(dwc_otg_pcd_t * pcd,
-+ const uint32_t epnum)
-+{
-+ /** @todo implement ISR */
-+ dwc_otg_core_if_t *core_if;
-+ doepmsk_data_t intr_mask = {.d32 = 0 };
-+
-+ DWC_DEBUGPL(DBG_ANY, "INTERRUPT Handler not implemented for %s\n", "OUT EP NAK");
-+ core_if = GET_CORE_IF(pcd);
-+ intr_mask.b.nak = 1;
-+
-+ if (core_if->multiproc_int_enable) {
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->
-+ doepeachintmsk[epnum], intr_mask.d32, 0);
-+ } else {
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->doepmsk,
-+ intr_mask.d32, 0);
-+ }
-+
-+ return 1;
-+}
-+
-+/**
-+ * Handler for the OUT EP NYET interrupt.
-+ */
-+static inline int32_t handle_out_ep_nyet_intr(dwc_otg_pcd_t * pcd,
-+ const uint32_t epnum)
-+{
-+ /** @todo implement ISR */
-+ dwc_otg_core_if_t *core_if;
-+ doepmsk_data_t intr_mask = {.d32 = 0 };
-+
-+ DWC_PRINTF("INTERRUPT Handler not implemented for %s\n", "OUT EP NYET");
-+ core_if = GET_CORE_IF(pcd);
-+ intr_mask.b.nyet = 1;
-+
-+ if (core_if->multiproc_int_enable) {
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->
-+ doepeachintmsk[epnum], intr_mask.d32, 0);
-+ } else {
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->doepmsk,
-+ intr_mask.d32, 0);
-+ }
-+
-+ return 1;
-+}
-+
-+/**
-+ * This interrupt indicates that an IN EP has a pending Interrupt.
-+ * The sequence for handling the IN EP interrupt is shown below:
-+ * -# Read the Device All Endpoint Interrupt register
-+ * -# Repeat the following for each IN EP interrupt bit set (from
-+ * LSB to MSB).
-+ * -# Read the Device Endpoint Interrupt (DIEPINTn) register
-+ * -# If "Transfer Complete" call the request complete function
-+ * -# If "Endpoint Disabled" complete the EP disable procedure.
-+ * -# If "AHB Error Interrupt" log error
-+ * -# If "Time-out Handshake" log error
-+ * -# If "IN Token Received when TxFIFO Empty" write packet to Tx
-+ * FIFO.
-+ * -# If "IN Token EP Mismatch" (disable, this is handled by EP
-+ * Mismatch Interrupt)
-+ */
-+static int32_t dwc_otg_pcd_handle_in_ep_intr(dwc_otg_pcd_t * pcd)
-+{
-+#define CLEAR_IN_EP_INTR(__core_if,__epnum,__intr) \
-+do { \
-+ diepint_data_t diepint = {.d32=0}; \
-+ diepint.b.__intr = 1; \
-+ DWC_WRITE_REG32(&__core_if->dev_if->in_ep_regs[__epnum]->diepint, \
-+ diepint.d32); \
-+} while (0)
-+
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+ dwc_otg_dev_if_t *dev_if = core_if->dev_if;
-+ diepint_data_t diepint = {.d32 = 0 };
-+ depctl_data_t depctl = {.d32 = 0 };
-+ uint32_t ep_intr;
-+ uint32_t epnum = 0;
-+ dwc_otg_pcd_ep_t *ep;
-+ dwc_ep_t *dwc_ep;
-+ gintmsk_data_t intr_mask = {.d32 = 0 };
-+
-+ DWC_DEBUGPL(DBG_PCDV, "%s(%p)\n", __func__, pcd);
-+
-+ /* Read in the device interrupt bits */
-+ ep_intr = dwc_otg_read_dev_all_in_ep_intr(core_if);
-+
-+ /* Service the Device IN interrupts for each endpoint */
-+ while (ep_intr) {
-+ if (ep_intr & 0x1) {
-+ uint32_t empty_msk;
-+ /* Get EP pointer */
-+ ep = get_in_ep(pcd, epnum);
-+ dwc_ep = &ep->dwc_ep;
-+
-+ depctl.d32 =
-+ DWC_READ_REG32(&dev_if->in_ep_regs[epnum]->diepctl);
-+ empty_msk =
-+ DWC_READ_REG32(&dev_if->
-+ dev_global_regs->dtknqr4_fifoemptymsk);
-+
-+ DWC_DEBUGPL(DBG_PCDV,
-+ "IN EP INTERRUPT - %d\nepmty_msk - %8x diepctl - %8x\n",
-+ epnum, empty_msk, depctl.d32);
-+
-+ DWC_DEBUGPL(DBG_PCD,
-+ "EP%d-%s: type=%d, mps=%d\n",
-+ dwc_ep->num, (dwc_ep->is_in ? "IN" : "OUT"),
-+ dwc_ep->type, dwc_ep->maxpacket);
-+
-+ diepint.d32 =
-+ dwc_otg_read_dev_in_ep_intr(core_if, dwc_ep);
-+
-+ DWC_DEBUGPL(DBG_PCDV,
-+ "EP %d Interrupt Register - 0x%x\n", epnum,
-+ diepint.d32);
-+ /* Transfer complete */
-+ if (diepint.b.xfercompl) {
-+ /* Disable the NP Tx FIFO Empty
-+ * Interrupt */
-+ if (core_if->en_multiple_tx_fifo == 0) {
-+ intr_mask.b.nptxfempty = 1;
-+ DWC_MODIFY_REG32
-+ (&core_if->core_global_regs->gintmsk,
-+ intr_mask.d32, 0);
-+ } else {
-+ /* Disable the Tx FIFO Empty Interrupt for this EP */
-+ uint32_t fifoemptymsk =
-+ 0x1 << dwc_ep->num;
-+ DWC_MODIFY_REG32(&core_if->
-+ dev_if->dev_global_regs->dtknqr4_fifoemptymsk,
-+ fifoemptymsk, 0);
-+ }
-+ /* Clear the bit in DIEPINTn for this interrupt */
-+ CLEAR_IN_EP_INTR(core_if, epnum, xfercompl);
-+
-+ /* Complete the transfer */
-+ if (epnum == 0) {
-+ handle_ep0(pcd);
-+ }
-+#ifdef DWC_EN_ISOC
-+ else if (dwc_ep->type == DWC_OTG_EP_TYPE_ISOC) {
-+ if (!ep->stopped)
-+ complete_iso_ep(pcd, ep);
-+ }
-+#endif /* DWC_EN_ISOC */
-+#ifdef DWC_UTE_PER_IO
-+ else if (dwc_ep->type == DWC_OTG_EP_TYPE_ISOC) {
-+ if (!ep->stopped)
-+ complete_xiso_ep(ep);
-+ }
-+#endif /* DWC_UTE_PER_IO */
-+ else {
-+ if (dwc_ep->type == DWC_OTG_EP_TYPE_ISOC &&
-+ dwc_ep->bInterval > 1) {
-+ dwc_ep->frame_num += dwc_ep->bInterval;
-+ if (dwc_ep->frame_num > 0x3FFF)
-+ {
-+ dwc_ep->frm_overrun = 1;
-+ dwc_ep->frame_num &= 0x3FFF;
-+ } else
-+ dwc_ep->frm_overrun = 0;
-+ }
-+ complete_ep(ep);
-+ if(diepint.b.nak)
-+ CLEAR_IN_EP_INTR(core_if, epnum, nak);
-+ }
-+ }
-+ /* Endpoint disable */
-+ if (diepint.b.epdisabled) {
-+ DWC_DEBUGPL(DBG_ANY, "EP%d IN disabled\n",
-+ epnum);
-+ handle_in_ep_disable_intr(pcd, epnum);
-+
-+ /* Clear the bit in DIEPINTn for this interrupt */
-+ CLEAR_IN_EP_INTR(core_if, epnum, epdisabled);
-+ }
-+ /* AHB Error */
-+ if (diepint.b.ahberr) {
-+ DWC_ERROR("EP%d IN AHB Error\n", epnum);
-+ /* Clear the bit in DIEPINTn for this interrupt */
-+ CLEAR_IN_EP_INTR(core_if, epnum, ahberr);
-+ }
-+ /* TimeOUT Handshake (non-ISOC IN EPs) */
-+ if (diepint.b.timeout) {
-+ DWC_ERROR("EP%d IN Time-out\n", epnum);
-+ handle_in_ep_timeout_intr(pcd, epnum);
-+
-+ CLEAR_IN_EP_INTR(core_if, epnum, timeout);
-+ }
-+ /** IN Token received with TxF Empty */
-+ if (diepint.b.intktxfemp) {
-+ DWC_DEBUGPL(DBG_ANY,
-+ "EP%d IN TKN TxFifo Empty\n",
-+ epnum);
-+ if (!ep->stopped && epnum != 0) {
-+
-+ diepmsk_data_t diepmsk = {.d32 = 0 };
-+ diepmsk.b.intktxfemp = 1;
-+
-+ if (core_if->multiproc_int_enable) {
-+ DWC_MODIFY_REG32
-+ (&dev_if->dev_global_regs->diepeachintmsk
-+ [epnum], diepmsk.d32, 0);
-+ } else {
-+ DWC_MODIFY_REG32
-+ (&dev_if->dev_global_regs->diepmsk,
-+ diepmsk.d32, 0);
-+ }
-+ } else if (core_if->dma_desc_enable
-+ && epnum == 0
-+ && pcd->ep0state ==
-+ EP0_OUT_STATUS_PHASE) {
-+ // EP0 IN set STALL
-+ depctl.d32 =
-+ DWC_READ_REG32(&dev_if->in_ep_regs
-+ [epnum]->diepctl);
-+
-+ /* set the disable and stall bits */
-+ if (depctl.b.epena) {
-+ depctl.b.epdis = 1;
-+ }
-+ depctl.b.stall = 1;
-+ DWC_WRITE_REG32(&dev_if->in_ep_regs
-+ [epnum]->diepctl,
-+ depctl.d32);
-+ }
-+ CLEAR_IN_EP_INTR(core_if, epnum, intktxfemp);
-+ }
-+ /** IN Token Received with EP mismatch */
-+ if (diepint.b.intknepmis) {
-+ DWC_DEBUGPL(DBG_ANY,
-+ "EP%d IN TKN EP Mismatch\n", epnum);
-+ CLEAR_IN_EP_INTR(core_if, epnum, intknepmis);
-+ }
-+ /** IN Endpoint NAK Effective */
-+ if (diepint.b.inepnakeff) {
-+ DWC_DEBUGPL(DBG_ANY,
-+ "EP%d IN EP NAK Effective\n",
-+ epnum);
-+ /* Periodic EP */
-+ if (ep->disabling) {
-+ depctl.d32 = 0;
-+ depctl.b.snak = 1;
-+ depctl.b.epdis = 1;
-+ DWC_MODIFY_REG32(&dev_if->in_ep_regs
-+ [epnum]->diepctl,
-+ depctl.d32,
-+ depctl.d32);
-+ }
-+ CLEAR_IN_EP_INTR(core_if, epnum, inepnakeff);
-+
-+ }
-+
-+ /** IN EP Tx FIFO Empty Intr */
-+ if (diepint.b.emptyintr) {
-+ DWC_DEBUGPL(DBG_ANY,
-+ "EP%d Tx FIFO Empty Intr \n",
-+ epnum);
-+ write_empty_tx_fifo(pcd, epnum);
-+
-+ CLEAR_IN_EP_INTR(core_if, epnum, emptyintr);
-+
-+ }
-+
-+ /** IN EP BNA Intr */
-+ if (diepint.b.bna) {
-+ CLEAR_IN_EP_INTR(core_if, epnum, bna);
-+ if (core_if->dma_desc_enable) {
-+#ifdef DWC_EN_ISOC
-+ if (dwc_ep->type ==
-+ DWC_OTG_EP_TYPE_ISOC) {
-+ /*
-+ * This checking is performed to prevent first "false" BNA
-+ * handling occuring right after reconnect
-+ */
-+ if (dwc_ep->next_frame !=
-+ 0xffffffff)
-+ dwc_otg_pcd_handle_iso_bna(ep);
-+ } else
-+#endif /* DWC_EN_ISOC */
-+ {
-+ dwc_otg_pcd_handle_noniso_bna(ep);
-+ }
-+ }
-+ }
-+ /* NAK Interrutp */
-+ if (diepint.b.nak) {
-+ DWC_DEBUGPL(DBG_ANY, "EP%d IN NAK Interrupt\n",
-+ epnum);
-+ if (ep->dwc_ep.type == DWC_OTG_EP_TYPE_ISOC) {
-+ depctl_data_t depctl;
-+ if (ep->dwc_ep.frame_num == 0xFFFFFFFF) {
-+ ep->dwc_ep.frame_num = core_if->frame_num;
-+ if (ep->dwc_ep.bInterval > 1) {
-+ depctl.d32 = 0;
-+ depctl.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[epnum]->diepctl);
-+ if (ep->dwc_ep.frame_num & 0x1) {
-+ depctl.b.setd1pid = 1;
-+ depctl.b.setd0pid = 0;
-+ } else {
-+ depctl.b.setd0pid = 1;
-+ depctl.b.setd1pid = 0;
-+ }
-+ DWC_WRITE_REG32(&dev_if->in_ep_regs[epnum]->diepctl, depctl.d32);
-+ }
-+ start_next_request(ep);
-+ }
-+ ep->dwc_ep.frame_num += ep->dwc_ep.bInterval;
-+ if (dwc_ep->frame_num > 0x3FFF) {
-+ dwc_ep->frm_overrun = 1;
-+ dwc_ep->frame_num &= 0x3FFF;
-+ } else
-+ dwc_ep->frm_overrun = 0;
-+ }
-+
-+ CLEAR_IN_EP_INTR(core_if, epnum, nak);
-+ }
-+ }
-+ epnum++;
-+ ep_intr >>= 1;
-+ }
-+
-+ return 1;
-+#undef CLEAR_IN_EP_INTR
-+}
-+
-+/**
-+ * This interrupt indicates that an OUT EP has a pending Interrupt.
-+ * The sequence for handling the OUT EP interrupt is shown below:
-+ * -# Read the Device All Endpoint Interrupt register
-+ * -# Repeat the following for each OUT EP interrupt bit set (from
-+ * LSB to MSB).
-+ * -# Read the Device Endpoint Interrupt (DOEPINTn) register
-+ * -# If "Transfer Complete" call the request complete function
-+ * -# If "Endpoint Disabled" complete the EP disable procedure.
-+ * -# If "AHB Error Interrupt" log error
-+ * -# If "Setup Phase Done" process Setup Packet (See Standard USB
-+ * Command Processing)
-+ */
-+static int32_t dwc_otg_pcd_handle_out_ep_intr(dwc_otg_pcd_t * pcd)
-+{
-+#define CLEAR_OUT_EP_INTR(__core_if,__epnum,__intr) \
-+do { \
-+ doepint_data_t doepint = {.d32=0}; \
-+ doepint.b.__intr = 1; \
-+ DWC_WRITE_REG32(&__core_if->dev_if->out_ep_regs[__epnum]->doepint, \
-+ doepint.d32); \
-+} while (0)
-+
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+ uint32_t ep_intr;
-+ doepint_data_t doepint = {.d32 = 0 };
-+ uint32_t epnum = 0;
-+ dwc_otg_pcd_ep_t *ep;
-+ dwc_ep_t *dwc_ep;
-+ dctl_data_t dctl = {.d32 = 0 };
-+ gintmsk_data_t gintmsk = {.d32 = 0 };
-+
-+
-+ DWC_DEBUGPL(DBG_PCDV, "%s()\n", __func__);
-+
-+ /* Read in the device interrupt bits */
-+ ep_intr = dwc_otg_read_dev_all_out_ep_intr(core_if);
-+
-+ while (ep_intr) {
-+ if (ep_intr & 0x1) {
-+ /* Get EP pointer */
-+ ep = get_out_ep(pcd, epnum);
-+ dwc_ep = &ep->dwc_ep;
-+
-+#ifdef VERBOSE
-+ DWC_DEBUGPL(DBG_PCDV,
-+ "EP%d-%s: type=%d, mps=%d\n",
-+ dwc_ep->num, (dwc_ep->is_in ? "IN" : "OUT"),
-+ dwc_ep->type, dwc_ep->maxpacket);
-+#endif
-+ doepint.d32 =
-+ dwc_otg_read_dev_out_ep_intr(core_if, dwc_ep);
-+ /* Moved this interrupt upper due to core deffect of asserting
-+ * OUT EP 0 xfercompl along with stsphsrcvd in BDMA */
-+ if (doepint.b.stsphsercvd) {
-+ deptsiz0_data_t deptsiz;
-+ CLEAR_OUT_EP_INTR(core_if, epnum, stsphsercvd);
-+ deptsiz.d32 =
-+ DWC_READ_REG32(&core_if->dev_if->
-+ out_ep_regs[0]->doeptsiz);
-+ if (core_if->snpsid >= OTG_CORE_REV_3_00a
-+ && core_if->dma_enable
-+ && core_if->dma_desc_enable == 0
-+ && doepint.b.xfercompl
-+ && deptsiz.b.xfersize == 24) {
-+ CLEAR_OUT_EP_INTR(core_if, epnum,
-+ xfercompl);
-+ doepint.b.xfercompl = 0;
-+ ep0_out_start(core_if, pcd);
-+ }
-+ if ((core_if->dma_desc_enable) ||
-+ (core_if->dma_enable
-+ && core_if->snpsid >=
-+ OTG_CORE_REV_3_00a)) {
-+ do_setup_in_status_phase(pcd);
-+ }
-+ }
-+ /* Transfer complete */
-+ if (doepint.b.xfercompl) {
-+
-+ if (epnum == 0) {
-+ /* Clear the bit in DOEPINTn for this interrupt */
-+ CLEAR_OUT_EP_INTR(core_if, epnum, xfercompl);
-+ if (core_if->snpsid >= OTG_CORE_REV_3_00a) {
-+ DWC_DEBUGPL(DBG_PCDV, "DOEPINT=%x doepint=%x\n",
-+ DWC_READ_REG32(&core_if->dev_if->out_ep_regs[0]->doepint),
-+ doepint.d32);
-+ DWC_DEBUGPL(DBG_PCDV, "DOEPCTL=%x \n",
-+ DWC_READ_REG32(&core_if->dev_if->out_ep_regs[0]->doepctl));
-+
-+ if (core_if->snpsid >= OTG_CORE_REV_3_00a
-+ && core_if->dma_enable == 0) {
-+ doepint_data_t doepint;
-+ doepint.d32 = DWC_READ_REG32(&core_if->dev_if->
-+ out_ep_regs[0]->doepint);
-+ if (pcd->ep0state == EP0_IDLE && doepint.b.sr) {
-+ CLEAR_OUT_EP_INTR(core_if, epnum, sr);
-+ goto exit_xfercompl;
-+ }
-+ }
-+ /* In case of DDMA look at SR bit to go to the Data Stage */
-+ if (core_if->dma_desc_enable) {
-+ dev_dma_desc_sts_t status = {.d32 = 0};
-+ if (pcd->ep0state == EP0_IDLE) {
-+ status.d32 = core_if->dev_if->setup_desc_addr[core_if->
-+ dev_if->setup_desc_index]->status.d32;
-+ if(pcd->data_terminated) {
-+ pcd->data_terminated = 0;
-+ status.d32 = core_if->dev_if->out_desc_addr->status.d32;
-+ dwc_memcpy(&pcd->setup_pkt->req, pcd->backup_buf, 8);
-+ }
-+ if (status.b.sr) {
-+ if (doepint.b.setup) {
-+ DWC_DEBUGPL(DBG_PCDV, "DMA DESC EP0_IDLE SR=1 setup=1\n");
-+ /* Already started data stage, clear setup */
-+ CLEAR_OUT_EP_INTR(core_if, epnum, setup);
-+ doepint.b.setup = 0;
-+ handle_ep0(pcd);
-+ /* Prepare for more setup packets */
-+ if (pcd->ep0state == EP0_IN_STATUS_PHASE ||
-+ pcd->ep0state == EP0_IN_DATA_PHASE) {
-+ ep0_out_start(core_if, pcd);
-+ }
-+
-+ goto exit_xfercompl;
-+ } else {
-+ /* Prepare for more setup packets */
-+ DWC_DEBUGPL(DBG_PCDV,
-+ "EP0_IDLE SR=1 setup=0 new setup comes\n");
-+ ep0_out_start(core_if, pcd);
-+ }
-+ }
-+ } else {
-+ dwc_otg_pcd_request_t *req;
-+ dev_dma_desc_sts_t status = {.d32 = 0};
-+ diepint_data_t diepint0;
-+ diepint0.d32 = DWC_READ_REG32(&core_if->dev_if->
-+ in_ep_regs[0]->diepint);
-+
-+ if (pcd->ep0state == EP0_STALL || pcd->ep0state == EP0_DISCONNECT) {
-+ DWC_ERROR("EP0 is stalled/disconnected\n");
-+ }
-+
-+ /* Clear IN xfercompl if set */
-+ if (diepint0.b.xfercompl && (pcd->ep0state == EP0_IN_STATUS_PHASE
-+ || pcd->ep0state == EP0_IN_DATA_PHASE)) {
-+ DWC_WRITE_REG32(&core_if->dev_if->
-+ in_ep_regs[0]->diepint, diepint0.d32);
-+ }
-+
-+ status.d32 = core_if->dev_if->setup_desc_addr[core_if->
-+ dev_if->setup_desc_index]->status.d32;
-+
-+ if (ep->dwc_ep.xfer_count != ep->dwc_ep.total_len
-+ && (pcd->ep0state == EP0_OUT_DATA_PHASE))
-+ status.d32 = core_if->dev_if->out_desc_addr->status.d32;
-+ if (pcd->ep0state == EP0_OUT_STATUS_PHASE)
-+ status.d32 = core_if->dev_if->
-+ out_desc_addr->status.d32;
-+
-+ if (status.b.sr) {
-+ if (DWC_CIRCLEQ_EMPTY(&ep->queue)) {
-+ DWC_DEBUGPL(DBG_PCDV, "Request queue empty!!\n");
-+ } else {
-+ DWC_DEBUGPL(DBG_PCDV, "complete req!!\n");
-+ req = DWC_CIRCLEQ_FIRST(&ep->queue);
-+ if (ep->dwc_ep.xfer_count != ep->dwc_ep.total_len &&
-+ pcd->ep0state == EP0_OUT_DATA_PHASE) {
-+ /* Read arrived setup packet from req->buf */
-+ dwc_memcpy(&pcd->setup_pkt->req,
-+ req->buf + ep->dwc_ep.xfer_count, 8);
-+ }
-+ req->actual = ep->dwc_ep.xfer_count;
-+ dwc_otg_request_done(ep, req, -ECONNRESET);
-+ ep->dwc_ep.start_xfer_buff = 0;
-+ ep->dwc_ep.xfer_buff = 0;
-+ ep->dwc_ep.xfer_len = 0;
-+ }
-+ pcd->ep0state = EP0_IDLE;
-+ if (doepint.b.setup) {
-+ DWC_DEBUGPL(DBG_PCDV, "EP0_IDLE SR=1 setup=1\n");
-+ /* Data stage started, clear setup */
-+ CLEAR_OUT_EP_INTR(core_if, epnum, setup);
-+ doepint.b.setup = 0;
-+ handle_ep0(pcd);
-+ /* Prepare for setup packets if ep0in was enabled*/
-+ if (pcd->ep0state == EP0_IN_STATUS_PHASE) {
-+ ep0_out_start(core_if, pcd);
-+ }
-+
-+ goto exit_xfercompl;
-+ } else {
-+ /* Prepare for more setup packets */
-+ DWC_DEBUGPL(DBG_PCDV,
-+ "EP0_IDLE SR=1 setup=0 new setup comes 2\n");
-+ ep0_out_start(core_if, pcd);
-+ }
-+ }
-+ }
-+ }
-+ if (core_if->snpsid >= OTG_CORE_REV_2_94a && core_if->dma_enable
-+ && core_if->dma_desc_enable == 0) {
-+ doepint_data_t doepint_temp = {.d32 = 0};
-+ deptsiz0_data_t doeptsize0 = {.d32 = 0 };
-+ doepint_temp.d32 = DWC_READ_REG32(&core_if->dev_if->
-+ out_ep_regs[ep->dwc_ep.num]->doepint);
-+ doeptsize0.d32 = DWC_READ_REG32(&core_if->dev_if->
-+ out_ep_regs[ep->dwc_ep.num]->doeptsiz);
-+ if (pcd->ep0state == EP0_IDLE) {
-+ if (doepint_temp.b.sr) {
-+ CLEAR_OUT_EP_INTR(core_if, epnum, sr);
-+ }
-+ doepint.d32 = DWC_READ_REG32(&core_if->dev_if->
-+ out_ep_regs[0]->doepint);
-+ if (doeptsize0.b.supcnt == 3) {
-+ DWC_DEBUGPL(DBG_ANY, "Rolling over!!!!!!!\n");
-+ ep->dwc_ep.stp_rollover = 1;
-+ }
-+ if (doepint.b.setup) {
-+retry:
-+ /* Already started data stage, clear setup */
-+ CLEAR_OUT_EP_INTR(core_if, epnum, setup);
-+ doepint.b.setup = 0;
-+ handle_ep0(pcd);
-+ ep->dwc_ep.stp_rollover = 0;
-+ /* Prepare for more setup packets */
-+ if (pcd->ep0state == EP0_IN_STATUS_PHASE ||
-+ pcd->ep0state == EP0_IN_DATA_PHASE) {
-+ ep0_out_start(core_if, pcd);
-+ }
-+ goto exit_xfercompl;
-+ } else {
-+ /* Prepare for more setup packets */
-+ DWC_DEBUGPL(DBG_ANY,
-+ "EP0_IDLE SR=1 setup=0 new setup comes\n");
-+ doepint.d32 = DWC_READ_REG32(&core_if->dev_if->
-+ out_ep_regs[0]->doepint);
-+ if(doepint.b.setup)
-+ goto retry;
-+ ep0_out_start(core_if, pcd);
-+ }
-+ } else {
-+ dwc_otg_pcd_request_t *req;
-+ diepint_data_t diepint0 = {.d32 = 0};
-+ doepint_data_t doepint_temp = {.d32 = 0};
-+ depctl_data_t diepctl0;
-+ diepint0.d32 = DWC_READ_REG32(&core_if->dev_if->
-+ in_ep_regs[0]->diepint);
-+ diepctl0.d32 = DWC_READ_REG32(&core_if->dev_if->
-+ in_ep_regs[0]->diepctl);
-+
-+ if (pcd->ep0state == EP0_IN_DATA_PHASE
-+ || pcd->ep0state == EP0_IN_STATUS_PHASE) {
-+ if (diepint0.b.xfercompl) {
-+ DWC_WRITE_REG32(&core_if->dev_if->
-+ in_ep_regs[0]->diepint, diepint0.d32);
-+ }
-+ if (diepctl0.b.epena) {
-+ diepint_data_t diepint = {.d32 = 0};
-+ diepctl0.b.snak = 1;
-+ DWC_WRITE_REG32(&core_if->dev_if->
-+ in_ep_regs[0]->diepctl, diepctl0.d32);
-+ do {
-+ dwc_udelay(10);
-+ diepint.d32 = DWC_READ_REG32(&core_if->dev_if->
-+ in_ep_regs[0]->diepint);
-+ } while (!diepint.b.inepnakeff);
-+ diepint.b.inepnakeff = 1;
-+ DWC_WRITE_REG32(&core_if->dev_if->
-+ in_ep_regs[0]->diepint, diepint.d32);
-+ diepctl0.d32 = 0;
-+ diepctl0.b.epdis = 1;
-+ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[0]->diepctl,
-+ diepctl0.d32);
-+ do {
-+ dwc_udelay(10);
-+ diepint.d32 = DWC_READ_REG32(&core_if->dev_if->
-+ in_ep_regs[0]->diepint);
-+ } while (!diepint.b.epdisabled);
-+ diepint.b.epdisabled = 1;
-+ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[0]->diepint,
-+ diepint.d32);
-+ }
-+ }
-+ doepint_temp.d32 = DWC_READ_REG32(&core_if->dev_if->
-+ out_ep_regs[ep->dwc_ep.num]->doepint);
-+ if (doepint_temp.b.sr) {
-+ CLEAR_OUT_EP_INTR(core_if, epnum, sr);
-+ if (DWC_CIRCLEQ_EMPTY(&ep->queue)) {
-+ DWC_DEBUGPL(DBG_PCDV, "Request queue empty!!\n");
-+ } else {
-+ DWC_DEBUGPL(DBG_PCDV, "complete req!!\n");
-+ req = DWC_CIRCLEQ_FIRST(&ep->queue);
-+ if (ep->dwc_ep.xfer_count != ep->dwc_ep.total_len &&
-+ pcd->ep0state == EP0_OUT_DATA_PHASE) {
-+ /* Read arrived setup packet from req->buf */
-+ dwc_memcpy(&pcd->setup_pkt->req,
-+ req->buf + ep->dwc_ep.xfer_count, 8);
-+ }
-+ req->actual = ep->dwc_ep.xfer_count;
-+ dwc_otg_request_done(ep, req, -ECONNRESET);
-+ ep->dwc_ep.start_xfer_buff = 0;
-+ ep->dwc_ep.xfer_buff = 0;
-+ ep->dwc_ep.xfer_len = 0;
-+ }
-+ pcd->ep0state = EP0_IDLE;
-+ if (doepint.b.setup) {
-+ DWC_DEBUGPL(DBG_PCDV, "EP0_IDLE SR=1 setup=1\n");
-+ /* Data stage started, clear setup */
-+ CLEAR_OUT_EP_INTR(core_if, epnum, setup);
-+ doepint.b.setup = 0;
-+ handle_ep0(pcd);
-+ /* Prepare for setup packets if ep0in was enabled*/
-+ if (pcd->ep0state == EP0_IN_STATUS_PHASE) {
-+ ep0_out_start(core_if, pcd);
-+ }
-+ goto exit_xfercompl;
-+ } else {
-+ /* Prepare for more setup packets */
-+ DWC_DEBUGPL(DBG_PCDV,
-+ "EP0_IDLE SR=1 setup=0 new setup comes 2\n");
-+ ep0_out_start(core_if, pcd);
-+ }
-+ }
-+ }
-+ }
-+ if (core_if->dma_enable == 0 || pcd->ep0state != EP0_IDLE)
-+ handle_ep0(pcd);
-+exit_xfercompl:
-+ DWC_DEBUGPL(DBG_PCDV, "DOEPINT=%x doepint=%x\n",
-+ dwc_otg_read_dev_out_ep_intr(core_if, dwc_ep), doepint.d32);
-+ } else {
-+ if (core_if->dma_desc_enable == 0
-+ || pcd->ep0state != EP0_IDLE)
-+ handle_ep0(pcd);
-+ }
-+#ifdef DWC_EN_ISOC
-+ } else if (dwc_ep->type == DWC_OTG_EP_TYPE_ISOC) {
-+ if (doepint.b.pktdrpsts == 0) {
-+ /* Clear the bit in DOEPINTn for this interrupt */
-+ CLEAR_OUT_EP_INTR(core_if,
-+ epnum,
-+ xfercompl);
-+ complete_iso_ep(pcd, ep);
-+ } else {
-+
-+ doepint_data_t doepint = {.d32 = 0 };
-+ doepint.b.xfercompl = 1;
-+ doepint.b.pktdrpsts = 1;
-+ DWC_WRITE_REG32
-+ (&core_if->dev_if->out_ep_regs
-+ [epnum]->doepint,
-+ doepint.d32);
-+ if (handle_iso_out_pkt_dropped
-+ (core_if, dwc_ep)) {
-+ complete_iso_ep(pcd,
-+ ep);
-+ }
-+ }
-+#endif /* DWC_EN_ISOC */
-+#ifdef DWC_UTE_PER_IO
-+ } else if (dwc_ep->type == DWC_OTG_EP_TYPE_ISOC) {
-+ CLEAR_OUT_EP_INTR(core_if, epnum, xfercompl);
-+ if (!ep->stopped)
-+ complete_xiso_ep(ep);
-+#endif /* DWC_UTE_PER_IO */
-+ } else {
-+ /* Clear the bit in DOEPINTn for this interrupt */
-+ CLEAR_OUT_EP_INTR(core_if, epnum,
-+ xfercompl);
-+
-+ if (core_if->core_params->dev_out_nak) {
-+ DWC_TIMER_CANCEL(pcd->core_if->ep_xfer_timer[epnum]);
-+ pcd->core_if->ep_xfer_info[epnum].state = 0;
-+#ifdef DEBUG
-+ print_memory_payload(pcd, dwc_ep);
-+#endif
-+ }
-+ complete_ep(ep);
-+ }
-+
-+ }
-+
-+ /* Endpoint disable */
-+ if (doepint.b.epdisabled) {
-+
-+ /* Clear the bit in DOEPINTn for this interrupt */
-+ CLEAR_OUT_EP_INTR(core_if, epnum, epdisabled);
-+ if (core_if->core_params->dev_out_nak) {
-+#ifdef DEBUG
-+ print_memory_payload(pcd, dwc_ep);
-+#endif
-+ /* In case of timeout condition */
-+ if (core_if->ep_xfer_info[epnum].state == 2) {
-+ dctl.d32 = DWC_READ_REG32(&core_if->dev_if->
-+ dev_global_regs->dctl);
-+ dctl.b.cgoutnak = 1;
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dctl,
-+ dctl.d32);
-+ /* Unmask goutnakeff interrupt which was masked
-+ * during handle nak out interrupt */
-+ gintmsk.b.goutnakeff = 1;
-+ DWC_MODIFY_REG32(&core_if->core_global_regs->gintmsk,
-+ 0, gintmsk.d32);
-+
-+ complete_ep(ep);
-+ }
-+ }
-+ if (ep->dwc_ep.type == DWC_OTG_EP_TYPE_ISOC)
-+ {
-+ dctl_data_t dctl;
-+ gintmsk_data_t intr_mask = {.d32 = 0};
-+ dwc_otg_pcd_request_t *req = 0;
-+
-+ dctl.d32 = DWC_READ_REG32(&core_if->dev_if->
-+ dev_global_regs->dctl);
-+ dctl.b.cgoutnak = 1;
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dctl,
-+ dctl.d32);
-+
-+ intr_mask.d32 = 0;
-+ intr_mask.b.incomplisoout = 1;
-+
-+ /* Get any pending requests */
-+ if (!DWC_CIRCLEQ_EMPTY(&ep->queue)) {
-+ req = DWC_CIRCLEQ_FIRST(&ep->queue);
-+ if (!req) {
-+ DWC_PRINTF("complete_ep 0x%p, req = NULL!\n", ep);
-+ } else {
-+ dwc_otg_request_done(ep, req, 0);
-+ start_next_request(ep);
-+ }
-+ } else {
-+ DWC_PRINTF("complete_ep 0x%p, ep->queue empty!\n", ep);
-+ }
-+ }
-+ }
-+ /* AHB Error */
-+ if (doepint.b.ahberr) {
-+ DWC_ERROR("EP%d OUT AHB Error\n", epnum);
-+ DWC_ERROR("EP%d DEPDMA=0x%08x \n",
-+ epnum, core_if->dev_if->out_ep_regs[epnum]->doepdma);
-+ CLEAR_OUT_EP_INTR(core_if, epnum, ahberr);
-+ }
-+ /* Setup Phase Done (contorl EPs) */
-+ if (doepint.b.setup) {
-+#ifdef DEBUG_EP0
-+ DWC_DEBUGPL(DBG_PCD, "EP%d SETUP Done\n", epnum);
-+#endif
-+ CLEAR_OUT_EP_INTR(core_if, epnum, setup);
-+
-+ handle_ep0(pcd);
-+ }
-+
-+ /** OUT EP BNA Intr */
-+ if (doepint.b.bna) {
-+ CLEAR_OUT_EP_INTR(core_if, epnum, bna);
-+ if (core_if->dma_desc_enable) {
-+#ifdef DWC_EN_ISOC
-+ if (dwc_ep->type ==
-+ DWC_OTG_EP_TYPE_ISOC) {
-+ /*
-+ * This checking is performed to prevent first "false" BNA
-+ * handling occuring right after reconnect
-+ */
-+ if (dwc_ep->next_frame !=
-+ 0xffffffff)
-+ dwc_otg_pcd_handle_iso_bna(ep);
-+ } else
-+#endif /* DWC_EN_ISOC */
-+ {
-+ dwc_otg_pcd_handle_noniso_bna(ep);
-+ }
-+ }
-+ }
-+ /* Babble Interrupt */
-+ if (doepint.b.babble) {
-+ DWC_DEBUGPL(DBG_ANY, "EP%d OUT Babble\n",
-+ epnum);
-+ handle_out_ep_babble_intr(pcd, epnum);
-+
-+ CLEAR_OUT_EP_INTR(core_if, epnum, babble);
-+ }
-+ if (doepint.b.outtknepdis) {
-+ DWC_DEBUGPL(DBG_ANY, "EP%d OUT Token received when EP is \
-+ disabled\n",epnum);
-+ if (ep->dwc_ep.type == DWC_OTG_EP_TYPE_ISOC) {
-+ doepmsk_data_t doepmsk = {.d32 = 0};
-+ ep->dwc_ep.frame_num = core_if->frame_num;
-+ if (ep->dwc_ep.bInterval > 1) {
-+ depctl_data_t depctl;
-+ depctl.d32 = DWC_READ_REG32(&core_if->dev_if->
-+ out_ep_regs[epnum]->doepctl);
-+ if (ep->dwc_ep.frame_num & 0x1) {
-+ depctl.b.setd1pid = 1;
-+ depctl.b.setd0pid = 0;
-+ } else {
-+ depctl.b.setd0pid = 1;
-+ depctl.b.setd1pid = 0;
-+ }
-+ DWC_WRITE_REG32(&core_if->dev_if->
-+ out_ep_regs[epnum]->doepctl, depctl.d32);
-+ }
-+ start_next_request(ep);
-+ doepmsk.b.outtknepdis = 1;
-+ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->doepmsk,
-+ doepmsk.d32, 0);
-+ }
-+ CLEAR_OUT_EP_INTR(core_if, epnum, outtknepdis);
-+ }
-+
-+ /* NAK Interrutp */
-+ if (doepint.b.nak) {
-+ DWC_DEBUGPL(DBG_ANY, "EP%d OUT NAK\n", epnum);
-+ handle_out_ep_nak_intr(pcd, epnum);
-+
-+ CLEAR_OUT_EP_INTR(core_if, epnum, nak);
-+ }
-+ /* NYET Interrutp */
-+ if (doepint.b.nyet) {
-+ DWC_DEBUGPL(DBG_ANY, "EP%d OUT NYET\n", epnum);
-+ handle_out_ep_nyet_intr(pcd, epnum);
-+
-+ CLEAR_OUT_EP_INTR(core_if, epnum, nyet);
-+ }
-+ }
-+
-+ epnum++;
-+ ep_intr >>= 1;
-+ }
-+
-+ return 1;
-+
-+#undef CLEAR_OUT_EP_INTR
-+}
-+static int drop_transfer(uint32_t trgt_fr, uint32_t curr_fr, uint8_t frm_overrun)
-+{
-+ int retval = 0;
-+ if(!frm_overrun && curr_fr >= trgt_fr)
-+ retval = 1;
-+ else if (frm_overrun
-+ && (curr_fr >= trgt_fr && ((curr_fr - trgt_fr) < 0x3FFF / 2)))
-+ retval = 1;
-+ return retval;
-+}
-+/**
-+ * Incomplete ISO IN Transfer Interrupt.
-+ * This interrupt indicates one of the following conditions occurred
-+ * while transmitting an ISOC transaction.
-+ * - Corrupted IN Token for ISOC EP.
-+ * - Packet not complete in FIFO.
-+ * The follow actions will be taken:
-+ * -# Determine the EP
-+ * -# Set incomplete flag in dwc_ep structure
-+ * -# Disable EP; when "Endpoint Disabled" interrupt is received
-+ * Flush FIFO
-+ */
-+int32_t dwc_otg_pcd_handle_incomplete_isoc_in_intr(dwc_otg_pcd_t * pcd)
-+{
-+ gintsts_data_t gintsts;
-+
-+#ifdef DWC_EN_ISOC
-+ dwc_otg_dev_if_t *dev_if;
-+ deptsiz_data_t deptsiz = {.d32 = 0 };
-+ depctl_data_t depctl = {.d32 = 0 };
-+ dsts_data_t dsts = {.d32 = 0 };
-+ dwc_ep_t *dwc_ep;
-+ int i;
-+
-+ dev_if = GET_CORE_IF(pcd)->dev_if;
-+
-+ for (i = 1; i <= dev_if->num_in_eps; ++i) {
-+ dwc_ep = &pcd->in_ep[i].dwc_ep;
-+ if (dwc_ep->active && dwc_ep->type == DWC_OTG_EP_TYPE_ISOC) {
-+ deptsiz.d32 =
-+ DWC_READ_REG32(&dev_if->in_ep_regs[i]->dieptsiz);
-+ depctl.d32 =
-+ DWC_READ_REG32(&dev_if->in_ep_regs[i]->diepctl);
-+
-+ if (depctl.b.epdis && deptsiz.d32) {
-+ set_current_pkt_info(GET_CORE_IF(pcd), dwc_ep);
-+ if (dwc_ep->cur_pkt >= dwc_ep->pkt_cnt) {
-+ dwc_ep->cur_pkt = 0;
-+ dwc_ep->proc_buf_num =
-+ (dwc_ep->proc_buf_num ^ 1) & 0x1;
-+
-+ if (dwc_ep->proc_buf_num) {
-+ dwc_ep->cur_pkt_addr =
-+ dwc_ep->xfer_buff1;
-+ dwc_ep->cur_pkt_dma_addr =
-+ dwc_ep->dma_addr1;
-+ } else {
-+ dwc_ep->cur_pkt_addr =
-+ dwc_ep->xfer_buff0;
-+ dwc_ep->cur_pkt_dma_addr =
-+ dwc_ep->dma_addr0;
-+ }
-+
-+ }
-+
-+ dsts.d32 =
-+ DWC_READ_REG32(&GET_CORE_IF(pcd)->dev_if->
-+ dev_global_regs->dsts);
-+ dwc_ep->next_frame = dsts.b.soffn;
-+
-+ dwc_otg_iso_ep_start_frm_transfer(GET_CORE_IF
-+ (pcd),
-+ dwc_ep);
-+ }
-+ }
-+ }
-+
-+#else
-+ depctl_data_t depctl = {.d32 = 0 };
-+ dwc_ep_t *dwc_ep;
-+ dwc_otg_dev_if_t *dev_if;
-+ int i;
-+ dev_if = GET_CORE_IF(pcd)->dev_if;
-+
-+ DWC_DEBUGPL(DBG_PCD,"Incomplete ISO IN \n");
-+
-+ for (i = 1; i <= dev_if->num_in_eps; ++i) {
-+ dwc_ep = &pcd->in_ep[i-1].dwc_ep;
-+ depctl.d32 =
-+ DWC_READ_REG32(&dev_if->in_ep_regs[i]->diepctl);
-+ if (depctl.b.epena && dwc_ep->type == DWC_OTG_EP_TYPE_ISOC) {
-+ if (drop_transfer(dwc_ep->frame_num, GET_CORE_IF(pcd)->frame_num,
-+ dwc_ep->frm_overrun))
-+ {
-+ depctl.d32 =
-+ DWC_READ_REG32(&dev_if->in_ep_regs[i]->diepctl);
-+ depctl.b.snak = 1;
-+ depctl.b.epdis = 1;
-+ DWC_MODIFY_REG32(&dev_if->in_ep_regs[i]->diepctl, depctl.d32, depctl.d32);
-+ }
-+ }
-+ }
-+
-+ /*intr_mask.b.incomplisoin = 1;
-+ DWC_MODIFY_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintmsk,
-+ intr_mask.d32, 0); */
-+#endif //DWC_EN_ISOC
-+
-+ /* Clear interrupt */
-+ gintsts.d32 = 0;
-+ gintsts.b.incomplisoin = 1;
-+ DWC_WRITE_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintsts,
-+ gintsts.d32);
-+
-+ return 1;
-+}
-+
-+/**
-+ * Incomplete ISO OUT Transfer Interrupt.
-+ *
-+ * This interrupt indicates that the core has dropped an ISO OUT
-+ * packet. The following conditions can be the cause:
-+ * - FIFO Full, the entire packet would not fit in the FIFO.
-+ * - CRC Error
-+ * - Corrupted Token
-+ * The follow actions will be taken:
-+ * -# Determine the EP
-+ * -# Set incomplete flag in dwc_ep structure
-+ * -# Read any data from the FIFO
-+ * -# Disable EP. When "Endpoint Disabled" interrupt is received
-+ * re-enable EP.
-+ */
-+int32_t dwc_otg_pcd_handle_incomplete_isoc_out_intr(dwc_otg_pcd_t * pcd)
-+{
-+
-+ gintsts_data_t gintsts;
-+
-+#ifdef DWC_EN_ISOC
-+ dwc_otg_dev_if_t *dev_if;
-+ deptsiz_data_t deptsiz = {.d32 = 0 };
-+ depctl_data_t depctl = {.d32 = 0 };
-+ dsts_data_t dsts = {.d32 = 0 };
-+ dwc_ep_t *dwc_ep;
-+ int i;
-+
-+ dev_if = GET_CORE_IF(pcd)->dev_if;
-+
-+ for (i = 1; i <= dev_if->num_out_eps; ++i) {
-+ dwc_ep = &pcd->in_ep[i].dwc_ep;
-+ if (pcd->out_ep[i].dwc_ep.active &&
-+ pcd->out_ep[i].dwc_ep.type == DWC_OTG_EP_TYPE_ISOC) {
-+ deptsiz.d32 =
-+ DWC_READ_REG32(&dev_if->out_ep_regs[i]->doeptsiz);
-+ depctl.d32 =
-+ DWC_READ_REG32(&dev_if->out_ep_regs[i]->doepctl);
-+
-+ if (depctl.b.epdis && deptsiz.d32) {
-+ set_current_pkt_info(GET_CORE_IF(pcd),
-+ &pcd->out_ep[i].dwc_ep);
-+ if (dwc_ep->cur_pkt >= dwc_ep->pkt_cnt) {
-+ dwc_ep->cur_pkt = 0;
-+ dwc_ep->proc_buf_num =
-+ (dwc_ep->proc_buf_num ^ 1) & 0x1;
-+
-+ if (dwc_ep->proc_buf_num) {
-+ dwc_ep->cur_pkt_addr =
-+ dwc_ep->xfer_buff1;
-+ dwc_ep->cur_pkt_dma_addr =
-+ dwc_ep->dma_addr1;
-+ } else {
-+ dwc_ep->cur_pkt_addr =
-+ dwc_ep->xfer_buff0;
-+ dwc_ep->cur_pkt_dma_addr =
-+ dwc_ep->dma_addr0;
-+ }
-+
-+ }
-+
-+ dsts.d32 =
-+ DWC_READ_REG32(&GET_CORE_IF(pcd)->dev_if->
-+ dev_global_regs->dsts);
-+ dwc_ep->next_frame = dsts.b.soffn;
-+
-+ dwc_otg_iso_ep_start_frm_transfer(GET_CORE_IF
-+ (pcd),
-+ dwc_ep);
-+ }
-+ }
-+ }
-+#else
-+ /** @todo implement ISR */
-+ gintmsk_data_t intr_mask = {.d32 = 0 };
-+ dwc_otg_core_if_t *core_if;
-+ deptsiz_data_t deptsiz = {.d32 = 0 };
-+ depctl_data_t depctl = {.d32 = 0 };
-+ dctl_data_t dctl = {.d32 = 0 };
-+ dwc_ep_t *dwc_ep = NULL;
-+ int i;
-+ core_if = GET_CORE_IF(pcd);
-+
-+ for (i = 0; i < core_if->dev_if->num_out_eps; ++i) {
-+ dwc_ep = &pcd->out_ep[i].dwc_ep;
-+ depctl.d32 =
-+ DWC_READ_REG32(&core_if->dev_if->out_ep_regs[dwc_ep->num]->doepctl);
-+ if (depctl.b.epena && depctl.b.dpid == (core_if->frame_num & 0x1)) {
-+ core_if->dev_if->isoc_ep = dwc_ep;
-+ deptsiz.d32 =
-+ DWC_READ_REG32(&core_if->dev_if->out_ep_regs[dwc_ep->num]->doeptsiz);
-+ break;
-+ }
-+ }
-+ dctl.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dctl);
-+ gintsts.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintsts);
-+ intr_mask.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintmsk);
-+
-+ if (!intr_mask.b.goutnakeff) {
-+ /* Unmask it */
-+ intr_mask.b.goutnakeff = 1;
-+ DWC_WRITE_REG32(&core_if->core_global_regs->gintmsk, intr_mask.d32);
-+ }
-+ if (!gintsts.b.goutnakeff) {
-+ dctl.b.sgoutnak = 1;
-+ }
-+ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dctl, dctl.d32);
-+
-+ depctl.d32 = DWC_READ_REG32(&core_if->dev_if->out_ep_regs[dwc_ep->num]->doepctl);
-+ if (depctl.b.epena) {
-+ depctl.b.epdis = 1;
-+ depctl.b.snak = 1;
-+ }
-+ DWC_WRITE_REG32(&core_if->dev_if->out_ep_regs[dwc_ep->num]->doepctl, depctl.d32);
-+
-+ intr_mask.d32 = 0;
-+ intr_mask.b.incomplisoout = 1;
-+
-+#endif /* DWC_EN_ISOC */
-+
-+ /* Clear interrupt */
-+ gintsts.d32 = 0;
-+ gintsts.b.incomplisoout = 1;
-+ DWC_WRITE_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintsts,
-+ gintsts.d32);
-+
-+ return 1;
-+}
-+
-+/**
-+ * This function handles the Global IN NAK Effective interrupt.
-+ *
-+ */
-+int32_t dwc_otg_pcd_handle_in_nak_effective(dwc_otg_pcd_t * pcd)
-+{
-+ dwc_otg_dev_if_t *dev_if = GET_CORE_IF(pcd)->dev_if;
-+ depctl_data_t diepctl = {.d32 = 0 };
-+ gintmsk_data_t intr_mask = {.d32 = 0 };
-+ gintsts_data_t gintsts;
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+ int i;
-+
-+ DWC_DEBUGPL(DBG_PCD, "Global IN NAK Effective\n");
-+
-+ /* Disable all active IN EPs */
-+ for (i = 0; i <= dev_if->num_in_eps; i++) {
-+ diepctl.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[i]->diepctl);
-+ if (!(diepctl.b.eptype & 1) && diepctl.b.epena) {
-+ if (core_if->start_predict > 0)
-+ core_if->start_predict++;
-+ diepctl.b.epdis = 1;
-+ diepctl.b.snak = 1;
-+ DWC_WRITE_REG32(&dev_if->in_ep_regs[i]->diepctl, diepctl.d32);
-+ }
-+ }
-+
-+
-+ /* Disable the Global IN NAK Effective Interrupt */
-+ intr_mask.b.ginnakeff = 1;
-+ DWC_MODIFY_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintmsk,
-+ intr_mask.d32, 0);
-+
-+ /* Clear interrupt */
-+ gintsts.d32 = 0;
-+ gintsts.b.ginnakeff = 1;
-+ DWC_WRITE_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintsts,
-+ gintsts.d32);
-+
-+ return 1;
-+}
-+
-+/**
-+ * OUT NAK Effective.
-+ *
-+ */
-+int32_t dwc_otg_pcd_handle_out_nak_effective(dwc_otg_pcd_t * pcd)
-+{
-+ dwc_otg_dev_if_t *dev_if = GET_CORE_IF(pcd)->dev_if;
-+ gintmsk_data_t intr_mask = {.d32 = 0 };
-+ gintsts_data_t gintsts;
-+ depctl_data_t doepctl;
-+ int i;
-+
-+ /* Disable the Global OUT NAK Effective Interrupt */
-+ intr_mask.b.goutnakeff = 1;
-+ DWC_MODIFY_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintmsk,
-+ intr_mask.d32, 0);
-+
-+ /* If DEV OUT NAK enabled*/
-+ if (pcd->core_if->core_params->dev_out_nak) {
-+ /* Run over all out endpoints to determine the ep number on
-+ * which the timeout has happened
-+ */
-+ for (i = 0; i <= dev_if->num_out_eps; i++) {
-+ if ( pcd->core_if->ep_xfer_info[i].state == 2 )
-+ break;
-+ }
-+ if (i > dev_if->num_out_eps) {
-+ dctl_data_t dctl;
-+ dctl.d32 =
-+ DWC_READ_REG32(&dev_if->dev_global_regs->dctl);
-+ dctl.b.cgoutnak = 1;
-+ DWC_WRITE_REG32(&dev_if->dev_global_regs->dctl,
-+ dctl.d32);
-+ goto out;
-+ }
-+
-+ /* Disable the endpoint */
-+ doepctl.d32 = DWC_READ_REG32(&dev_if->out_ep_regs[i]->doepctl);
-+ if (doepctl.b.epena) {
-+ doepctl.b.epdis = 1;
-+ doepctl.b.snak = 1;
-+ }
-+ DWC_WRITE_REG32(&dev_if->out_ep_regs[i]->doepctl, doepctl.d32);
-+ return 1;
-+ }
-+ /* We come here from Incomplete ISO OUT handler */
-+ if (dev_if->isoc_ep) {
-+ dwc_ep_t *dwc_ep = (dwc_ep_t *)dev_if->isoc_ep;
-+ uint32_t epnum = dwc_ep->num;
-+ doepint_data_t doepint;
-+ doepint.d32 =
-+ DWC_READ_REG32(&dev_if->out_ep_regs[dwc_ep->num]->doepint);
-+ dev_if->isoc_ep = NULL;
-+ doepctl.d32 =
-+ DWC_READ_REG32(&dev_if->out_ep_regs[epnum]->doepctl);
-+ DWC_PRINTF("Before disable DOEPCTL = %08x\n", doepctl.d32);
-+ if (doepctl.b.epena) {
-+ doepctl.b.epdis = 1;
-+ doepctl.b.snak = 1;
-+ }
-+ DWC_WRITE_REG32(&dev_if->out_ep_regs[epnum]->doepctl,
-+ doepctl.d32);
-+ return 1;
-+ } else
-+ DWC_PRINTF("INTERRUPT Handler not implemented for %s\n",
-+ "Global OUT NAK Effective\n");
-+
-+out:
-+ /* Clear interrupt */
-+ gintsts.d32 = 0;
-+ gintsts.b.goutnakeff = 1;
-+ DWC_WRITE_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintsts,
-+ gintsts.d32);
-+
-+ return 1;
-+}
-+
-+/**
-+ * PCD interrupt handler.
-+ *
-+ * The PCD handles the device interrupts. Many conditions can cause a
-+ * device interrupt. When an interrupt occurs, the device interrupt
-+ * service routine determines the cause of the interrupt and
-+ * dispatches handling to the appropriate function. These interrupt
-+ * handling functions are described below.
-+ *
-+ * All interrupt registers are processed from LSB to MSB.
-+ *
-+ */
-+int32_t dwc_otg_pcd_handle_intr(dwc_otg_pcd_t * pcd)
-+{
-+ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd);
-+#ifdef VERBOSE
-+ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs;
-+#endif
-+ gintsts_data_t gintr_status;
-+ int32_t retval = 0;
-+
-+ /* Exit from ISR if core is hibernated */
-+ if (core_if->hibernation_suspend == 1) {
-+ return retval;
-+ }
-+#ifdef VERBOSE
-+ DWC_DEBUGPL(DBG_ANY, "%s() gintsts=%08x gintmsk=%08x\n",
-+ __func__,
-+ DWC_READ_REG32(&global_regs->gintsts),
-+ DWC_READ_REG32(&global_regs->gintmsk));
-+#endif
-+
-+ if (dwc_otg_is_device_mode(core_if)) {
-+ DWC_SPINLOCK(pcd->lock);
-+#ifdef VERBOSE
-+ DWC_DEBUGPL(DBG_PCDV, "%s() gintsts=%08x gintmsk=%08x\n",
-+ __func__,
-+ DWC_READ_REG32(&global_regs->gintsts),
-+ DWC_READ_REG32(&global_regs->gintmsk));
-+#endif
-+
-+ gintr_status.d32 = dwc_otg_read_core_intr(core_if);
-+
-+ DWC_DEBUGPL(DBG_PCDV, "%s: gintsts&gintmsk=%08x\n",
-+ __func__, gintr_status.d32);
-+
-+ if (gintr_status.b.sofintr) {
-+ retval |= dwc_otg_pcd_handle_sof_intr(pcd);
-+ }
-+ if (gintr_status.b.rxstsqlvl) {
-+ retval |=
-+ dwc_otg_pcd_handle_rx_status_q_level_intr(pcd);
-+ }
-+ if (gintr_status.b.nptxfempty) {
-+ retval |= dwc_otg_pcd_handle_np_tx_fifo_empty_intr(pcd);
-+ }
-+ if (gintr_status.b.goutnakeff) {
-+ retval |= dwc_otg_pcd_handle_out_nak_effective(pcd);
-+ }
-+ if (gintr_status.b.i2cintr) {
-+ retval |= dwc_otg_pcd_handle_i2c_intr(pcd);
-+ }
-+ if (gintr_status.b.erlysuspend) {
-+ retval |= dwc_otg_pcd_handle_early_suspend_intr(pcd);
-+ }
-+ if (gintr_status.b.usbreset) {
-+ retval |= dwc_otg_pcd_handle_usb_reset_intr(pcd);
-+ }
-+ if (gintr_status.b.enumdone) {
-+ retval |= dwc_otg_pcd_handle_enum_done_intr(pcd);
-+ }
-+ if (gintr_status.b.isooutdrop) {
-+ retval |=
-+ dwc_otg_pcd_handle_isoc_out_packet_dropped_intr
-+ (pcd);
-+ }
-+ if (gintr_status.b.eopframe) {
-+ retval |=
-+ dwc_otg_pcd_handle_end_periodic_frame_intr(pcd);
-+ }
-+ if (gintr_status.b.inepint) {
-+ if (!core_if->multiproc_int_enable) {
-+ retval |= dwc_otg_pcd_handle_in_ep_intr(pcd);
-+ }
-+ }
-+ if (gintr_status.b.outepintr) {
-+ if (!core_if->multiproc_int_enable) {
-+ retval |= dwc_otg_pcd_handle_out_ep_intr(pcd);
-+ }
-+ }
-+ if (gintr_status.b.epmismatch) {
-+ retval |= dwc_otg_pcd_handle_ep_mismatch_intr(pcd);
-+ }
-+ if (gintr_status.b.fetsusp) {
-+ retval |= dwc_otg_pcd_handle_ep_fetsusp_intr(pcd);
-+ }
-+ if (gintr_status.b.ginnakeff) {
-+ retval |= dwc_otg_pcd_handle_in_nak_effective(pcd);
-+ }
-+ if (gintr_status.b.incomplisoin) {
-+ retval |=
-+ dwc_otg_pcd_handle_incomplete_isoc_in_intr(pcd);
-+ }
-+ if (gintr_status.b.incomplisoout) {
-+ retval |=
-+ dwc_otg_pcd_handle_incomplete_isoc_out_intr(pcd);
-+ }
-+
-+ /* In MPI mode Device Endpoints interrupts are asserted
-+ * without setting outepintr and inepint bits set, so these
-+ * Interrupt handlers are called without checking these bit-fields
-+ */
-+ if (core_if->multiproc_int_enable) {
-+ retval |= dwc_otg_pcd_handle_in_ep_intr(pcd);
-+ retval |= dwc_otg_pcd_handle_out_ep_intr(pcd);
-+ }
-+#ifdef VERBOSE
-+ DWC_DEBUGPL(DBG_PCDV, "%s() gintsts=%0x\n", __func__,
-+ DWC_READ_REG32(&global_regs->gintsts));
-+#endif
-+ DWC_SPINUNLOCK(pcd->lock);
-+ }
-+ return retval;
-+}
-+
-+#endif /* DWC_HOST_ONLY */
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_pcd_linux.c
-@@ -0,0 +1,1280 @@
-+ /* ==========================================================================
-+ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_pcd_linux.c $
-+ * $Revision: #21 $
-+ * $Date: 2012/08/10 $
-+ * $Change: 2047372 $
-+ *
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+#ifndef DWC_HOST_ONLY
-+
-+/** @file
-+ * This file implements the Peripheral Controller Driver.
-+ *
-+ * The Peripheral Controller Driver (PCD) is responsible for
-+ * translating requests from the Function Driver into the appropriate
-+ * actions on the DWC_otg controller. It isolates the Function Driver
-+ * from the specifics of the controller by providing an API to the
-+ * Function Driver.
-+ *
-+ * The Peripheral Controller Driver for Linux will implement the
-+ * Gadget API, so that the existing Gadget drivers can be used.
-+ * (Gadget Driver is the Linux terminology for a Function Driver.)
-+ *
-+ * The Linux Gadget API is defined in the header file
-+ * <code><linux/usb_gadget.h></code>. The USB EP operations API is
-+ * defined in the structure <code>usb_ep_ops</code> and the USB
-+ * Controller API is defined in the structure
-+ * <code>usb_gadget_ops</code>.
-+ *
-+ */
-+
-+#include "dwc_otg_os_dep.h"
-+#include "dwc_otg_pcd_if.h"
-+#include "dwc_otg_pcd.h"
-+#include "dwc_otg_driver.h"
-+#include "dwc_otg_dbg.h"
-+
-+extern bool fiq_enable;
-+
-+static struct gadget_wrapper {
-+ dwc_otg_pcd_t *pcd;
-+
-+ struct usb_gadget gadget;
-+ struct usb_gadget_driver *driver;
-+
-+ struct usb_ep ep0;
-+ struct usb_ep in_ep[16];
-+ struct usb_ep out_ep[16];
-+
-+} *gadget_wrapper;
-+
-+/* Display the contents of the buffer */
-+extern void dump_msg(const u8 * buf, unsigned int length);
-+/**
-+ * Get the dwc_otg_pcd_ep_t* from usb_ep* pointer - NULL in case
-+ * if the endpoint is not found
-+ */
-+static struct dwc_otg_pcd_ep *ep_from_handle(dwc_otg_pcd_t * pcd, void *handle)
-+{
-+ int i;
-+ if (pcd->ep0.priv == handle) {
-+ return &pcd->ep0;
-+ }
-+
-+ for (i = 0; i < MAX_EPS_CHANNELS - 1; i++) {
-+ if (pcd->in_ep[i].priv == handle)
-+ return &pcd->in_ep[i];
-+ if (pcd->out_ep[i].priv == handle)
-+ return &pcd->out_ep[i];
-+ }
-+
-+ return NULL;
-+}
-+
-+/* USB Endpoint Operations */
-+/*
-+ * The following sections briefly describe the behavior of the Gadget
-+ * API endpoint operations implemented in the DWC_otg driver
-+ * software. Detailed descriptions of the generic behavior of each of
-+ * these functions can be found in the Linux header file
-+ * include/linux/usb_gadget.h.
-+ *
-+ * The Gadget API provides wrapper functions for each of the function
-+ * pointers defined in usb_ep_ops. The Gadget Driver calls the wrapper
-+ * function, which then calls the underlying PCD function. The
-+ * following sections are named according to the wrapper
-+ * functions. Within each section, the corresponding DWC_otg PCD
-+ * function name is specified.
-+ *
-+ */
-+
-+/**
-+ * This function is called by the Gadget Driver for each EP to be
-+ * configured for the current configuration (SET_CONFIGURATION).
-+ *
-+ * This function initializes the dwc_otg_ep_t data structure, and then
-+ * calls dwc_otg_ep_activate.
-+ */
-+static int ep_enable(struct usb_ep *usb_ep,
-+ const struct usb_endpoint_descriptor *ep_desc)
-+{
-+ int retval;
-+
-+ DWC_DEBUGPL(DBG_PCDV, "%s(%p,%p)\n", __func__, usb_ep, ep_desc);
-+
-+ if (!usb_ep || !ep_desc || ep_desc->bDescriptorType != USB_DT_ENDPOINT) {
-+ DWC_WARN("%s, bad ep or descriptor\n", __func__);
-+ return -EINVAL;
-+ }
-+ if (usb_ep == &gadget_wrapper->ep0) {
-+ DWC_WARN("%s, bad ep(0)\n", __func__);
-+ return -EINVAL;
-+ }
-+
-+ /* Check FIFO size? */
-+ if (!ep_desc->wMaxPacketSize) {
-+ DWC_WARN("%s, bad %s maxpacket\n", __func__, usb_ep->name);
-+ return -ERANGE;
-+ }
-+
-+ if (!gadget_wrapper->driver ||
-+ gadget_wrapper->gadget.speed == USB_SPEED_UNKNOWN) {
-+ DWC_WARN("%s, bogus device state\n", __func__);
-+ return -ESHUTDOWN;
-+ }
-+
-+ /* Delete after check - MAS */
-+#if 0
-+ nat = (uint32_t) ep_desc->wMaxPacketSize;
-+ printk(KERN_ALERT "%s: nat (before) =%d\n", __func__, nat);
-+ nat = (nat >> 11) & 0x03;
-+ printk(KERN_ALERT "%s: nat (after) =%d\n", __func__, nat);
-+#endif
-+ retval = dwc_otg_pcd_ep_enable(gadget_wrapper->pcd,
-+ (const uint8_t *)ep_desc,
-+ (void *)usb_ep);
-+ if (retval) {
-+ DWC_WARN("dwc_otg_pcd_ep_enable failed\n");
-+ return -EINVAL;
-+ }
-+
-+ usb_ep->maxpacket = le16_to_cpu(ep_desc->wMaxPacketSize);
-+
-+ return 0;
-+}
-+
-+/**
-+ * This function is called when an EP is disabled due to disconnect or
-+ * change in configuration. Any pending requests will terminate with a
-+ * status of -ESHUTDOWN.
-+ *
-+ * This function modifies the dwc_otg_ep_t data structure for this EP,
-+ * and then calls dwc_otg_ep_deactivate.
-+ */
-+static int ep_disable(struct usb_ep *usb_ep)
-+{
-+ int retval;
-+
-+ DWC_DEBUGPL(DBG_PCDV, "%s(%p)\n", __func__, usb_ep);
-+ if (!usb_ep) {
-+ DWC_DEBUGPL(DBG_PCD, "%s, %s not enabled\n", __func__,
-+ usb_ep ? usb_ep->name : NULL);
-+ return -EINVAL;
-+ }
-+
-+ retval = dwc_otg_pcd_ep_disable(gadget_wrapper->pcd, usb_ep);
-+ if (retval) {
-+ retval = -EINVAL;
-+ }
-+
-+ return retval;
-+}
-+
-+/**
-+ * This function allocates a request object to use with the specified
-+ * endpoint.
-+ *
-+ * @param ep The endpoint to be used with with the request
-+ * @param gfp_flags the GFP_* flags to use.
-+ */
-+static struct usb_request *dwc_otg_pcd_alloc_request(struct usb_ep *ep,
-+ gfp_t gfp_flags)
-+{
-+ struct usb_request *usb_req;
-+
-+ DWC_DEBUGPL(DBG_PCDV, "%s(%p,%d)\n", __func__, ep, gfp_flags);
-+ if (0 == ep) {
-+ DWC_WARN("%s() %s\n", __func__, "Invalid EP!\n");
-+ return 0;
-+ }
-+ usb_req = kmalloc(sizeof(*usb_req), gfp_flags);
-+ if (0 == usb_req) {
-+ DWC_WARN("%s() %s\n", __func__, "request allocation failed!\n");
-+ return 0;
-+ }
-+ memset(usb_req, 0, sizeof(*usb_req));
-+ usb_req->dma = DWC_DMA_ADDR_INVALID;
-+
-+ return usb_req;
-+}
-+
-+/**
-+ * This function frees a request object.
-+ *
-+ * @param ep The endpoint associated with the request
-+ * @param req The request being freed
-+ */
-+static void dwc_otg_pcd_free_request(struct usb_ep *ep, struct usb_request *req)
-+{
-+ DWC_DEBUGPL(DBG_PCDV, "%s(%p,%p)\n", __func__, ep, req);
-+
-+ if (0 == ep || 0 == req) {
-+ DWC_WARN("%s() %s\n", __func__,
-+ "Invalid ep or req argument!\n");
-+ return;
-+ }
-+
-+ kfree(req);
-+}
-+
-+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28)
-+/**
-+ * This function allocates an I/O buffer to be used for a transfer
-+ * to/from the specified endpoint.
-+ *
-+ * @param usb_ep The endpoint to be used with with the request
-+ * @param bytes The desired number of bytes for the buffer
-+ * @param dma Pointer to the buffer's DMA address; must be valid
-+ * @param gfp_flags the GFP_* flags to use.
-+ * @return address of a new buffer or null is buffer could not be allocated.
-+ */
-+static void *dwc_otg_pcd_alloc_buffer(struct usb_ep *usb_ep, unsigned bytes,
-+ dma_addr_t * dma, gfp_t gfp_flags)
-+{
-+ void *buf;
-+ dwc_otg_pcd_t *pcd = 0;
-+
-+ pcd = gadget_wrapper->pcd;
-+
-+ DWC_DEBUGPL(DBG_PCDV, "%s(%p,%d,%p,%0x)\n", __func__, usb_ep, bytes,
-+ dma, gfp_flags);
-+
-+ /* Check dword alignment */
-+ if ((bytes & 0x3UL) != 0) {
-+ DWC_WARN("%s() Buffer size is not a multiple of"
-+ "DWORD size (%d)", __func__, bytes);
-+ }
-+
-+ buf = dma_alloc_coherent(NULL, bytes, dma, gfp_flags);
-+
-+ /* Check dword alignment */
-+ if (((int)buf & 0x3UL) != 0) {
-+ DWC_WARN("%s() Buffer is not DWORD aligned (%p)",
-+ __func__, buf);
-+ }
-+
-+ return buf;
-+}
-+
-+/**
-+ * This function frees an I/O buffer that was allocated by alloc_buffer.
-+ *
-+ * @param usb_ep the endpoint associated with the buffer
-+ * @param buf address of the buffer
-+ * @param dma The buffer's DMA address
-+ * @param bytes The number of bytes of the buffer
-+ */
-+static void dwc_otg_pcd_free_buffer(struct usb_ep *usb_ep, void *buf,
-+ dma_addr_t dma, unsigned bytes)
-+{
-+ dwc_otg_pcd_t *pcd = 0;
-+
-+ pcd = gadget_wrapper->pcd;
-+
-+ DWC_DEBUGPL(DBG_PCDV, "%s(%p,%0x,%d)\n", __func__, buf, dma, bytes);
-+
-+ dma_free_coherent(NULL, bytes, buf, dma);
-+}
-+#endif
-+
-+/**
-+ * This function is used to submit an I/O Request to an EP.
-+ *
-+ * - When the request completes the request's completion callback
-+ * is called to return the request to the driver.
-+ * - An EP, except control EPs, may have multiple requests
-+ * pending.
-+ * - Once submitted the request cannot be examined or modified.
-+ * - Each request is turned into one or more packets.
-+ * - A BULK EP can queue any amount of data; the transfer is
-+ * packetized.
-+ * - Zero length Packets are specified with the request 'zero'
-+ * flag.
-+ */
-+static int ep_queue(struct usb_ep *usb_ep, struct usb_request *usb_req,
-+ gfp_t gfp_flags)
-+{
-+ dwc_otg_pcd_t *pcd;
-+ struct dwc_otg_pcd_ep *ep = NULL;
-+ int retval = 0, is_isoc_ep = 0;
-+ dma_addr_t dma_addr = DWC_DMA_ADDR_INVALID;
-+
-+ DWC_DEBUGPL(DBG_PCDV, "%s(%p,%p,%d)\n",
-+ __func__, usb_ep, usb_req, gfp_flags);
-+
-+ if (!usb_req || !usb_req->complete || !usb_req->buf) {
-+ DWC_WARN("bad params\n");
-+ return -EINVAL;
-+ }
-+
-+ if (!usb_ep) {
-+ DWC_WARN("bad ep\n");
-+ return -EINVAL;
-+ }
-+
-+ pcd = gadget_wrapper->pcd;
-+ if (!gadget_wrapper->driver ||
-+ gadget_wrapper->gadget.speed == USB_SPEED_UNKNOWN) {
-+ DWC_DEBUGPL(DBG_PCDV, "gadget.speed=%d\n",
-+ gadget_wrapper->gadget.speed);
-+ DWC_WARN("bogus device state\n");
-+ return -ESHUTDOWN;
-+ }
-+
-+ DWC_DEBUGPL(DBG_PCD, "%s queue req %p, len %d buf %p\n",
-+ usb_ep->name, usb_req, usb_req->length, usb_req->buf);
-+
-+ usb_req->status = -EINPROGRESS;
-+ usb_req->actual = 0;
-+
-+ ep = ep_from_handle(pcd, usb_ep);
-+ if (ep == NULL)
-+ is_isoc_ep = 0;
-+ else
-+ is_isoc_ep = (ep->dwc_ep.type == DWC_OTG_EP_TYPE_ISOC) ? 1 : 0;
-+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28)
-+ dma_addr = usb_req->dma;
-+#else
-+ if (GET_CORE_IF(pcd)->dma_enable) {
-+ dwc_otg_device_t *otg_dev = gadget_wrapper->pcd->otg_dev;
-+ struct device *dev = NULL;
-+
-+ if (otg_dev != NULL)
-+ dev = DWC_OTG_OS_GETDEV(otg_dev->os_dep);
-+
-+ if (usb_req->length != 0 &&
-+ usb_req->dma == DWC_DMA_ADDR_INVALID) {
-+ dma_addr = dma_map_single(dev, usb_req->buf,
-+ usb_req->length,
-+ ep->dwc_ep.is_in ?
-+ DMA_TO_DEVICE:
-+ DMA_FROM_DEVICE);
-+ }
-+ }
-+#endif
-+
-+#ifdef DWC_UTE_PER_IO
-+ if (is_isoc_ep == 1) {
-+ retval = dwc_otg_pcd_xiso_ep_queue(pcd, usb_ep, usb_req->buf, dma_addr,
-+ usb_req->length, usb_req->zero, usb_req,
-+ gfp_flags == GFP_ATOMIC ? 1 : 0, &usb_req->ext_req);
-+ if (retval)
-+ return -EINVAL;
-+
-+ return 0;
-+ }
-+#endif
-+ retval = dwc_otg_pcd_ep_queue(pcd, usb_ep, usb_req->buf, dma_addr,
-+ usb_req->length, usb_req->zero, usb_req,
-+ gfp_flags == GFP_ATOMIC ? 1 : 0);
-+ if (retval) {
-+ return -EINVAL;
-+ }
-+
-+ return 0;
-+}
-+
-+/**
-+ * This function cancels an I/O request from an EP.
-+ */
-+static int ep_dequeue(struct usb_ep *usb_ep, struct usb_request *usb_req)
-+{
-+ DWC_DEBUGPL(DBG_PCDV, "%s(%p,%p)\n", __func__, usb_ep, usb_req);
-+
-+ if (!usb_ep || !usb_req) {
-+ DWC_WARN("bad argument\n");
-+ return -EINVAL;
-+ }
-+ if (!gadget_wrapper->driver ||
-+ gadget_wrapper->gadget.speed == USB_SPEED_UNKNOWN) {
-+ DWC_WARN("bogus device state\n");
-+ return -ESHUTDOWN;
-+ }
-+ if (dwc_otg_pcd_ep_dequeue(gadget_wrapper->pcd, usb_ep, usb_req)) {
-+ return -EINVAL;
-+ }
-+
-+ return 0;
-+}
-+
-+/**
-+ * usb_ep_set_halt stalls an endpoint.
-+ *
-+ * usb_ep_clear_halt clears an endpoint halt and resets its data
-+ * toggle.
-+ *
-+ * Both of these functions are implemented with the same underlying
-+ * function. The behavior depends on the value argument.
-+ *
-+ * @param[in] usb_ep the Endpoint to halt or clear halt.
-+ * @param[in] value
-+ * - 0 means clear_halt.
-+ * - 1 means set_halt,
-+ * - 2 means clear stall lock flag.
-+ * - 3 means set stall lock flag.
-+ */
-+static int ep_halt(struct usb_ep *usb_ep, int value)
-+{
-+ int retval = 0;
-+
-+ DWC_DEBUGPL(DBG_PCD, "HALT %s %d\n", usb_ep->name, value);
-+
-+ if (!usb_ep) {
-+ DWC_WARN("bad ep\n");
-+ return -EINVAL;
-+ }
-+
-+ retval = dwc_otg_pcd_ep_halt(gadget_wrapper->pcd, usb_ep, value);
-+ if (retval == -DWC_E_AGAIN) {
-+ return -EAGAIN;
-+ } else if (retval) {
-+ retval = -EINVAL;
-+ }
-+
-+ return retval;
-+}
-+
-+//#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,30))
-+#if 0
-+/**
-+ * ep_wedge: sets the halt feature and ignores clear requests
-+ *
-+ * @usb_ep: the endpoint being wedged
-+ *
-+ * Use this to stall an endpoint and ignore CLEAR_FEATURE(HALT_ENDPOINT)
-+ * requests. If the gadget driver clears the halt status, it will
-+ * automatically unwedge the endpoint.
-+ *
-+ * Returns zero on success, else negative errno. *
-+ * Check usb_ep_set_wedge() at "usb_gadget.h" for details
-+ */
-+static int ep_wedge(struct usb_ep *usb_ep)
-+{
-+ int retval = 0;
-+
-+ DWC_DEBUGPL(DBG_PCD, "WEDGE %s\n", usb_ep->name);
-+
-+ if (!usb_ep) {
-+ DWC_WARN("bad ep\n");
-+ return -EINVAL;
-+ }
-+
-+ retval = dwc_otg_pcd_ep_wedge(gadget_wrapper->pcd, usb_ep);
-+ if (retval == -DWC_E_AGAIN) {
-+ retval = -EAGAIN;
-+ } else if (retval) {
-+ retval = -EINVAL;
-+ }
-+
-+ return retval;
-+}
-+#endif
-+
-+#ifdef DWC_EN_ISOC
-+/**
-+ * This function is used to submit an ISOC Transfer Request to an EP.
-+ *
-+ * - Every time a sync period completes the request's completion callback
-+ * is called to provide data to the gadget driver.
-+ * - Once submitted the request cannot be modified.
-+ * - Each request is turned into periodic data packets untill ISO
-+ * Transfer is stopped..
-+ */
-+static int iso_ep_start(struct usb_ep *usb_ep, struct usb_iso_request *req,
-+ gfp_t gfp_flags)
-+{
-+ int retval = 0;
-+
-+ if (!req || !req->process_buffer || !req->buf0 || !req->buf1) {
-+ DWC_WARN("bad params\n");
-+ return -EINVAL;
-+ }
-+
-+ if (!usb_ep) {
-+ DWC_PRINTF("bad params\n");
-+ return -EINVAL;
-+ }
-+
-+ req->status = -EINPROGRESS;
-+
-+ retval =
-+ dwc_otg_pcd_iso_ep_start(gadget_wrapper->pcd, usb_ep, req->buf0,
-+ req->buf1, req->dma0, req->dma1,
-+ req->sync_frame, req->data_pattern_frame,
-+ req->data_per_frame,
-+ req->
-+ flags & USB_REQ_ISO_ASAP ? -1 :
-+ req->start_frame, req->buf_proc_intrvl,
-+ req, gfp_flags == GFP_ATOMIC ? 1 : 0);
-+
-+ if (retval) {
-+ return -EINVAL;
-+ }
-+
-+ return retval;
-+}
-+
-+/**
-+ * This function stops ISO EP Periodic Data Transfer.
-+ */
-+static int iso_ep_stop(struct usb_ep *usb_ep, struct usb_iso_request *req)
-+{
-+ int retval = 0;
-+ if (!usb_ep) {
-+ DWC_WARN("bad ep\n");
-+ }
-+
-+ if (!gadget_wrapper->driver ||
-+ gadget_wrapper->gadget.speed == USB_SPEED_UNKNOWN) {
-+ DWC_DEBUGPL(DBG_PCDV, "gadget.speed=%d\n",
-+ gadget_wrapper->gadget.speed);
-+ DWC_WARN("bogus device state\n");
-+ }
-+
-+ dwc_otg_pcd_iso_ep_stop(gadget_wrapper->pcd, usb_ep, req);
-+ if (retval) {
-+ retval = -EINVAL;
-+ }
-+
-+ return retval;
-+}
-+
-+static struct usb_iso_request *alloc_iso_request(struct usb_ep *ep,
-+ int packets, gfp_t gfp_flags)
-+{
-+ struct usb_iso_request *pReq = NULL;
-+ uint32_t req_size;
-+
-+ req_size = sizeof(struct usb_iso_request);
-+ req_size +=
-+ (2 * packets * (sizeof(struct usb_gadget_iso_packet_descriptor)));
-+
-+ pReq = kmalloc(req_size, gfp_flags);
-+ if (!pReq) {
-+ DWC_WARN("Can't allocate Iso Request\n");
-+ return 0;
-+ }
-+ pReq->iso_packet_desc0 = (void *)(pReq + 1);
-+
-+ pReq->iso_packet_desc1 = pReq->iso_packet_desc0 + packets;
-+
-+ return pReq;
-+}
-+
-+static void free_iso_request(struct usb_ep *ep, struct usb_iso_request *req)
-+{
-+ kfree(req);
-+}
-+
-+static struct usb_isoc_ep_ops dwc_otg_pcd_ep_ops = {
-+ .ep_ops = {
-+ .enable = ep_enable,
-+ .disable = ep_disable,
-+
-+ .alloc_request = dwc_otg_pcd_alloc_request,
-+ .free_request = dwc_otg_pcd_free_request,
-+
-+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28)
-+ .alloc_buffer = dwc_otg_pcd_alloc_buffer,
-+ .free_buffer = dwc_otg_pcd_free_buffer,
-+#endif
-+
-+ .queue = ep_queue,
-+ .dequeue = ep_dequeue,
-+
-+ .set_halt = ep_halt,
-+ .fifo_status = 0,
-+ .fifo_flush = 0,
-+ },
-+ .iso_ep_start = iso_ep_start,
-+ .iso_ep_stop = iso_ep_stop,
-+ .alloc_iso_request = alloc_iso_request,
-+ .free_iso_request = free_iso_request,
-+};
-+
-+#else
-+
-+ int (*enable) (struct usb_ep *ep,
-+ const struct usb_endpoint_descriptor *desc);
-+ int (*disable) (struct usb_ep *ep);
-+
-+ struct usb_request *(*alloc_request) (struct usb_ep *ep,
-+ gfp_t gfp_flags);
-+ void (*free_request) (struct usb_ep *ep, struct usb_request *req);
-+
-+ int (*queue) (struct usb_ep *ep, struct usb_request *req,
-+ gfp_t gfp_flags);
-+ int (*dequeue) (struct usb_ep *ep, struct usb_request *req);
-+
-+ int (*set_halt) (struct usb_ep *ep, int value);
-+ int (*set_wedge) (struct usb_ep *ep);
-+
-+ int (*fifo_status) (struct usb_ep *ep);
-+ void (*fifo_flush) (struct usb_ep *ep);
-+static struct usb_ep_ops dwc_otg_pcd_ep_ops = {
-+ .enable = ep_enable,
-+ .disable = ep_disable,
-+
-+ .alloc_request = dwc_otg_pcd_alloc_request,
-+ .free_request = dwc_otg_pcd_free_request,
-+
-+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28)
-+ .alloc_buffer = dwc_otg_pcd_alloc_buffer,
-+ .free_buffer = dwc_otg_pcd_free_buffer,
-+#else
-+ /* .set_wedge = ep_wedge, */
-+ .set_wedge = NULL, /* uses set_halt instead */
-+#endif
-+
-+ .queue = ep_queue,
-+ .dequeue = ep_dequeue,
-+
-+ .set_halt = ep_halt,
-+ .fifo_status = 0,
-+ .fifo_flush = 0,
-+
-+};
-+
-+#endif /* _EN_ISOC_ */
-+/* Gadget Operations */
-+/**
-+ * The following gadget operations will be implemented in the DWC_otg
-+ * PCD. Functions in the API that are not described below are not
-+ * implemented.
-+ *
-+ * The Gadget API provides wrapper functions for each of the function
-+ * pointers defined in usb_gadget_ops. The Gadget Driver calls the
-+ * wrapper function, which then calls the underlying PCD function. The
-+ * following sections are named according to the wrapper functions
-+ * (except for ioctl, which doesn't have a wrapper function). Within
-+ * each section, the corresponding DWC_otg PCD function name is
-+ * specified.
-+ *
-+ */
-+
-+/**
-+ *Gets the USB Frame number of the last SOF.
-+ */
-+static int get_frame_number(struct usb_gadget *gadget)
-+{
-+ struct gadget_wrapper *d;
-+
-+ DWC_DEBUGPL(DBG_PCDV, "%s(%p)\n", __func__, gadget);
-+
-+ if (gadget == 0) {
-+ return -ENODEV;
-+ }
-+
-+ d = container_of(gadget, struct gadget_wrapper, gadget);
-+ return dwc_otg_pcd_get_frame_number(d->pcd);
-+}
-+
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+static int test_lpm_enabled(struct usb_gadget *gadget)
-+{
-+ struct gadget_wrapper *d;
-+
-+ d = container_of(gadget, struct gadget_wrapper, gadget);
-+
-+ return dwc_otg_pcd_is_lpm_enabled(d->pcd);
-+}
-+#endif
-+
-+/**
-+ * Initiates Session Request Protocol (SRP) to wakeup the host if no
-+ * session is in progress. If a session is already in progress, but
-+ * the device is suspended, remote wakeup signaling is started.
-+ *
-+ */
-+static int wakeup(struct usb_gadget *gadget)
-+{
-+ struct gadget_wrapper *d;
-+
-+ DWC_DEBUGPL(DBG_PCDV, "%s(%p)\n", __func__, gadget);
-+
-+ if (gadget == 0) {
-+ return -ENODEV;
-+ } else {
-+ d = container_of(gadget, struct gadget_wrapper, gadget);
-+ }
-+ dwc_otg_pcd_wakeup(d->pcd);
-+ return 0;
-+}
-+
-+static const struct usb_gadget_ops dwc_otg_pcd_ops = {
-+ .get_frame = get_frame_number,
-+ .wakeup = wakeup,
-+#ifdef CONFIG_USB_DWC_OTG_LPM
-+ .lpm_support = test_lpm_enabled,
-+#endif
-+ // current versions must always be self-powered
-+};
-+
-+static int _setup(dwc_otg_pcd_t * pcd, uint8_t * bytes)
-+{
-+ int retval = -DWC_E_NOT_SUPPORTED;
-+ if (gadget_wrapper->driver && gadget_wrapper->driver->setup) {
-+ retval = gadget_wrapper->driver->setup(&gadget_wrapper->gadget,
-+ (struct usb_ctrlrequest
-+ *)bytes);
-+ }
-+
-+ if (retval == -ENOTSUPP) {
-+ retval = -DWC_E_NOT_SUPPORTED;
-+ } else if (retval < 0) {
-+ retval = -DWC_E_INVALID;
-+ }
-+
-+ return retval;
-+}
-+
-+#ifdef DWC_EN_ISOC
-+static int _isoc_complete(dwc_otg_pcd_t * pcd, void *ep_handle,
-+ void *req_handle, int proc_buf_num)
-+{
-+ int i, packet_count;
-+ struct usb_gadget_iso_packet_descriptor *iso_packet = 0;
-+ struct usb_iso_request *iso_req = req_handle;
-+
-+ if (proc_buf_num) {
-+ iso_packet = iso_req->iso_packet_desc1;
-+ } else {
-+ iso_packet = iso_req->iso_packet_desc0;
-+ }
-+ packet_count =
-+ dwc_otg_pcd_get_iso_packet_count(pcd, ep_handle, req_handle);
-+ for (i = 0; i < packet_count; ++i) {
-+ int status;
-+ int actual;
-+ int offset;
-+ dwc_otg_pcd_get_iso_packet_params(pcd, ep_handle, req_handle,
-+ i, &status, &actual, &offset);
-+ switch (status) {
-+ case -DWC_E_NO_DATA:
-+ status = -ENODATA;
-+ break;
-+ default:
-+ if (status) {
-+ DWC_PRINTF("unknown status in isoc packet\n");
-+ }
-+
-+ }
-+ iso_packet[i].status = status;
-+ iso_packet[i].offset = offset;
-+ iso_packet[i].actual_length = actual;
-+ }
-+
-+ iso_req->status = 0;
-+ iso_req->process_buffer(ep_handle, iso_req);
-+
-+ return 0;
-+}
-+#endif /* DWC_EN_ISOC */
-+
-+#ifdef DWC_UTE_PER_IO
-+/**
-+ * Copy the contents of the extended request to the Linux usb_request's
-+ * extended part and call the gadget's completion.
-+ *
-+ * @param pcd Pointer to the pcd structure
-+ * @param ep_handle Void pointer to the usb_ep structure
-+ * @param req_handle Void pointer to the usb_request structure
-+ * @param status Request status returned from the portable logic
-+ * @param ereq_port Void pointer to the extended request structure
-+ * created in the the portable part that contains the
-+ * results of the processed iso packets.
-+ */
-+static int _xisoc_complete(dwc_otg_pcd_t * pcd, void *ep_handle,
-+ void *req_handle, int32_t status, void *ereq_port)
-+{
-+ struct dwc_ute_iso_req_ext *ereqorg = NULL;
-+ struct dwc_iso_xreq_port *ereqport = NULL;
-+ struct dwc_ute_iso_packet_descriptor *desc_org = NULL;
-+ int i;
-+ struct usb_request *req;
-+ //struct dwc_ute_iso_packet_descriptor *
-+ //int status = 0;
-+
-+ req = (struct usb_request *)req_handle;
-+ ereqorg = &req->ext_req;
-+ ereqport = (struct dwc_iso_xreq_port *)ereq_port;
-+ desc_org = ereqorg->per_io_frame_descs;
-+
-+ if (req && req->complete) {
-+ /* Copy the request data from the portable logic to our request */
-+ for (i = 0; i < ereqport->pio_pkt_count; i++) {
-+ desc_org[i].actual_length =
-+ ereqport->per_io_frame_descs[i].actual_length;
-+ desc_org[i].status =
-+ ereqport->per_io_frame_descs[i].status;
-+ }
-+
-+ switch (status) {
-+ case -DWC_E_SHUTDOWN:
-+ req->status = -ESHUTDOWN;
-+ break;
-+ case -DWC_E_RESTART:
-+ req->status = -ECONNRESET;
-+ break;
-+ case -DWC_E_INVALID:
-+ req->status = -EINVAL;
-+ break;
-+ case -DWC_E_TIMEOUT:
-+ req->status = -ETIMEDOUT;
-+ break;
-+ default:
-+ req->status = status;
-+ }
-+
-+ /* And call the gadget's completion */
-+ req->complete(ep_handle, req);
-+ }
-+
-+ return 0;
-+}
-+#endif /* DWC_UTE_PER_IO */
-+
-+static int _complete(dwc_otg_pcd_t * pcd, void *ep_handle,
-+ void *req_handle, int32_t status, uint32_t actual)
-+{
-+ struct usb_request *req = (struct usb_request *)req_handle;
-+#if LINUX_VERSION_CODE > KERNEL_VERSION(2,6,27)
-+ struct dwc_otg_pcd_ep *ep = NULL;
-+#endif
-+
-+ if (req && req->complete) {
-+ switch (status) {
-+ case -DWC_E_SHUTDOWN:
-+ req->status = -ESHUTDOWN;
-+ break;
-+ case -DWC_E_RESTART:
-+ req->status = -ECONNRESET;
-+ break;
-+ case -DWC_E_INVALID:
-+ req->status = -EINVAL;
-+ break;
-+ case -DWC_E_TIMEOUT:
-+ req->status = -ETIMEDOUT;
-+ break;
-+ default:
-+ req->status = status;
-+
-+ }
-+
-+ req->actual = actual;
-+ DWC_SPINUNLOCK(pcd->lock);
-+ req->complete(ep_handle, req);
-+ DWC_SPINLOCK(pcd->lock);
-+ }
-+#if LINUX_VERSION_CODE > KERNEL_VERSION(2,6,27)
-+ ep = ep_from_handle(pcd, ep_handle);
-+ if (GET_CORE_IF(pcd)->dma_enable) {
-+ if (req->length != 0) {
-+ dwc_otg_device_t *otg_dev = gadget_wrapper->pcd->otg_dev;
-+ struct device *dev = NULL;
-+
-+ if (otg_dev != NULL)
-+ dev = DWC_OTG_OS_GETDEV(otg_dev->os_dep);
-+
-+ dma_unmap_single(dev, req->dma, req->length,
-+ ep->dwc_ep.is_in ?
-+ DMA_TO_DEVICE: DMA_FROM_DEVICE);
-+ }
-+ }
-+#endif
-+
-+ return 0;
-+}
-+
-+static int _connect(dwc_otg_pcd_t * pcd, int speed)
-+{
-+ gadget_wrapper->gadget.speed = speed;
-+ return 0;
-+}
-+
-+static int _disconnect(dwc_otg_pcd_t * pcd)
-+{
-+ if (gadget_wrapper->driver && gadget_wrapper->driver->disconnect) {
-+ gadget_wrapper->driver->disconnect(&gadget_wrapper->gadget);
-+ }
-+ return 0;
-+}
-+
-+static int _resume(dwc_otg_pcd_t * pcd)
-+{
-+ if (gadget_wrapper->driver && gadget_wrapper->driver->resume) {
-+ gadget_wrapper->driver->resume(&gadget_wrapper->gadget);
-+ }
-+
-+ return 0;
-+}
-+
-+static int _suspend(dwc_otg_pcd_t * pcd)
-+{
-+ if (gadget_wrapper->driver && gadget_wrapper->driver->suspend) {
-+ gadget_wrapper->driver->suspend(&gadget_wrapper->gadget);
-+ }
-+ return 0;
-+}
-+
-+/**
-+ * This function updates the otg values in the gadget structure.
-+ */
-+static int _hnp_changed(dwc_otg_pcd_t * pcd)
-+{
-+
-+ if (!gadget_wrapper->gadget.is_otg)
-+ return 0;
-+
-+ gadget_wrapper->gadget.b_hnp_enable = get_b_hnp_enable(pcd);
-+ gadget_wrapper->gadget.a_hnp_support = get_a_hnp_support(pcd);
-+ gadget_wrapper->gadget.a_alt_hnp_support = get_a_alt_hnp_support(pcd);
-+ return 0;
-+}
-+
-+static int _reset(dwc_otg_pcd_t * pcd)
-+{
-+ return 0;
-+}
-+
-+#ifdef DWC_UTE_CFI
-+static int _cfi_setup(dwc_otg_pcd_t * pcd, void *cfi_req)
-+{
-+ int retval = -DWC_E_INVALID;
-+ if (gadget_wrapper->driver->cfi_feature_setup) {
-+ retval =
-+ gadget_wrapper->driver->
-+ cfi_feature_setup(&gadget_wrapper->gadget,
-+ (struct cfi_usb_ctrlrequest *)cfi_req);
-+ }
-+
-+ return retval;
-+}
-+#endif
-+
-+static const struct dwc_otg_pcd_function_ops fops = {
-+ .complete = _complete,
-+#ifdef DWC_EN_ISOC
-+ .isoc_complete = _isoc_complete,
-+#endif
-+ .setup = _setup,
-+ .disconnect = _disconnect,
-+ .connect = _connect,
-+ .resume = _resume,
-+ .suspend = _suspend,
-+ .hnp_changed = _hnp_changed,
-+ .reset = _reset,
-+#ifdef DWC_UTE_CFI
-+ .cfi_setup = _cfi_setup,
-+#endif
-+#ifdef DWC_UTE_PER_IO
-+ .xisoc_complete = _xisoc_complete,
-+#endif
-+};
-+
-+/**
-+ * This function is the top level PCD interrupt handler.
-+ */
-+static irqreturn_t dwc_otg_pcd_irq(int irq, void *dev)
-+{
-+ dwc_otg_pcd_t *pcd = dev;
-+ int32_t retval = IRQ_NONE;
-+
-+ retval = dwc_otg_pcd_handle_intr(pcd);
-+ if (retval != 0) {
-+ S3C2410X_CLEAR_EINTPEND();
-+ }
-+ return IRQ_RETVAL(retval);
-+}
-+
-+/**
-+ * This function initialized the usb_ep structures to there default
-+ * state.
-+ *
-+ * @param d Pointer on gadget_wrapper.
-+ */
-+void gadget_add_eps(struct gadget_wrapper *d)
-+{
-+ static const char *names[] = {
-+
-+ "ep0",
-+ "ep1in",
-+ "ep2in",
-+ "ep3in",
-+ "ep4in",
-+ "ep5in",
-+ "ep6in",
-+ "ep7in",
-+ "ep8in",
-+ "ep9in",
-+ "ep10in",
-+ "ep11in",
-+ "ep12in",
-+ "ep13in",
-+ "ep14in",
-+ "ep15in",
-+ "ep1out",
-+ "ep2out",
-+ "ep3out",
-+ "ep4out",
-+ "ep5out",
-+ "ep6out",
-+ "ep7out",
-+ "ep8out",
-+ "ep9out",
-+ "ep10out",
-+ "ep11out",
-+ "ep12out",
-+ "ep13out",
-+ "ep14out",
-+ "ep15out"
-+ };
-+
-+ int i;
-+ struct usb_ep *ep;
-+ int8_t dev_endpoints;
-+
-+ DWC_DEBUGPL(DBG_PCDV, "%s\n", __func__);
-+
-+ INIT_LIST_HEAD(&d->gadget.ep_list);
-+ d->gadget.ep0 = &d->ep0;
-+ d->gadget.speed = USB_SPEED_UNKNOWN;
-+
-+ INIT_LIST_HEAD(&d->gadget.ep0->ep_list);
-+
-+ /**
-+ * Initialize the EP0 structure.
-+ */
-+ ep = &d->ep0;
-+
-+ /* Init the usb_ep structure. */
-+ ep->name = names[0];
-+ ep->ops = (struct usb_ep_ops *)&dwc_otg_pcd_ep_ops;
-+
-+ /**
-+ * @todo NGS: What should the max packet size be set to
-+ * here? Before EP type is set?
-+ */
-+ ep->maxpacket = MAX_PACKET_SIZE;
-+ dwc_otg_pcd_ep_enable(d->pcd, NULL, ep);
-+
-+ list_add_tail(&ep->ep_list, &d->gadget.ep_list);
-+
-+ /**
-+ * Initialize the EP structures.
-+ */
-+ dev_endpoints = d->pcd->core_if->dev_if->num_in_eps;
-+
-+ for (i = 0; i < dev_endpoints; i++) {
-+ ep = &d->in_ep[i];
-+
-+ /* Init the usb_ep structure. */
-+ ep->name = names[d->pcd->in_ep[i].dwc_ep.num];
-+ ep->ops = (struct usb_ep_ops *)&dwc_otg_pcd_ep_ops;
-+
-+ /**
-+ * @todo NGS: What should the max packet size be set to
-+ * here? Before EP type is set?
-+ */
-+ ep->maxpacket = MAX_PACKET_SIZE;
-+ list_add_tail(&ep->ep_list, &d->gadget.ep_list);
-+ }
-+
-+ dev_endpoints = d->pcd->core_if->dev_if->num_out_eps;
-+
-+ for (i = 0; i < dev_endpoints; i++) {
-+ ep = &d->out_ep[i];
-+
-+ /* Init the usb_ep structure. */
-+ ep->name = names[15 + d->pcd->out_ep[i].dwc_ep.num];
-+ ep->ops = (struct usb_ep_ops *)&dwc_otg_pcd_ep_ops;
-+
-+ /**
-+ * @todo NGS: What should the max packet size be set to
-+ * here? Before EP type is set?
-+ */
-+ ep->maxpacket = MAX_PACKET_SIZE;
-+
-+ list_add_tail(&ep->ep_list, &d->gadget.ep_list);
-+ }
-+
-+ /* remove ep0 from the list. There is a ep0 pointer. */
-+ list_del_init(&d->ep0.ep_list);
-+
-+ d->ep0.maxpacket = MAX_EP0_SIZE;
-+}
-+
-+/**
-+ * This function releases the Gadget device.
-+ * required by device_unregister().
-+ *
-+ * @todo Should this do something? Should it free the PCD?
-+ */
-+static void dwc_otg_pcd_gadget_release(struct device *dev)
-+{
-+ DWC_DEBUGPL(DBG_PCDV, "%s(%p)\n", __func__, dev);
-+}
-+
-+static struct gadget_wrapper *alloc_wrapper(dwc_bus_dev_t *_dev)
-+{
-+ static char pcd_name[] = "dwc_otg_pcd";
-+ dwc_otg_device_t *otg_dev = DWC_OTG_BUSDRVDATA(_dev);
-+ struct gadget_wrapper *d;
-+ int retval;
-+
-+ d = DWC_ALLOC(sizeof(*d));
-+ if (d == NULL) {
-+ return NULL;
-+ }
-+
-+ memset(d, 0, sizeof(*d));
-+
-+ d->gadget.name = pcd_name;
-+ d->pcd = otg_dev->pcd;
-+
-+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,30)
-+ strcpy(d->gadget.dev.bus_id, "gadget");
-+#else
-+ dev_set_name(&d->gadget.dev, "%s", "gadget");
-+#endif
-+
-+ d->gadget.dev.parent = &_dev->dev;
-+ d->gadget.dev.release = dwc_otg_pcd_gadget_release;
-+ d->gadget.ops = &dwc_otg_pcd_ops;
-+ d->gadget.max_speed = dwc_otg_pcd_is_dualspeed(otg_dev->pcd) ? USB_SPEED_HIGH:USB_SPEED_FULL;
-+ d->gadget.is_otg = dwc_otg_pcd_is_otg(otg_dev->pcd);
-+
-+ d->driver = 0;
-+ /* Register the gadget device */
-+ retval = device_register(&d->gadget.dev);
-+ if (retval != 0) {
-+ DWC_ERROR("device_register failed\n");
-+ DWC_FREE(d);
-+ return NULL;
-+ }
-+
-+ return d;
-+}
-+
-+static void free_wrapper(struct gadget_wrapper *d)
-+{
-+ if (d->driver) {
-+ /* should have been done already by driver model core */
-+ DWC_WARN("driver '%s' is still registered\n",
-+ d->driver->driver.name);
-+#ifdef CONFIG_USB_GADGET
-+ usb_gadget_unregister_driver(d->driver);
-+#endif
-+ }
-+
-+ device_unregister(&d->gadget.dev);
-+ DWC_FREE(d);
-+}
-+
-+/**
-+ * This function initialized the PCD portion of the driver.
-+ *
-+ */
-+int pcd_init(dwc_bus_dev_t *_dev)
-+{
-+ dwc_otg_device_t *otg_dev = DWC_OTG_BUSDRVDATA(_dev);
-+ int retval = 0;
-+
-+ DWC_DEBUGPL(DBG_PCDV, "%s(%p) otg_dev=%p\n", __func__, _dev, otg_dev);
-+
-+ otg_dev->pcd = dwc_otg_pcd_init(otg_dev->core_if);
-+
-+ if (!otg_dev->pcd) {
-+ DWC_ERROR("dwc_otg_pcd_init failed\n");
-+ return -ENOMEM;
-+ }
-+
-+ otg_dev->pcd->otg_dev = otg_dev;
-+ gadget_wrapper = alloc_wrapper(_dev);
-+
-+ /*
-+ * Initialize EP structures
-+ */
-+ gadget_add_eps(gadget_wrapper);
-+ /*
-+ * Setup interupt handler
-+ */
-+#ifdef PLATFORM_INTERFACE
-+ DWC_DEBUGPL(DBG_ANY, "registering handler for irq%d\n",
-+ platform_get_irq(_dev, fiq_enable ? 0 : 1));
-+ retval = request_irq(platform_get_irq(_dev, fiq_enable ? 0 : 1), dwc_otg_pcd_irq,
-+ IRQF_SHARED, gadget_wrapper->gadget.name,
-+ otg_dev->pcd);
-+ if (retval != 0) {
-+ DWC_ERROR("request of irq%d failed\n",
-+ platform_get_irq(_dev, fiq_enable ? 0 : 1));
-+ free_wrapper(gadget_wrapper);
-+ return -EBUSY;
-+ }
-+#else
-+ DWC_DEBUGPL(DBG_ANY, "registering handler for irq%d\n",
-+ _dev->irq);
-+ retval = request_irq(_dev->irq, dwc_otg_pcd_irq,
-+ IRQF_SHARED | IRQF_DISABLED,
-+ gadget_wrapper->gadget.name, otg_dev->pcd);
-+ if (retval != 0) {
-+ DWC_ERROR("request of irq%d failed\n", _dev->irq);
-+ free_wrapper(gadget_wrapper);
-+ return -EBUSY;
-+ }
-+#endif
-+
-+ dwc_otg_pcd_start(gadget_wrapper->pcd, &fops);
-+
-+ return retval;
-+}
-+
-+/**
-+ * Cleanup the PCD.
-+ */
-+void pcd_remove(dwc_bus_dev_t *_dev)
-+{
-+ dwc_otg_device_t *otg_dev = DWC_OTG_BUSDRVDATA(_dev);
-+ dwc_otg_pcd_t *pcd = otg_dev->pcd;
-+
-+ DWC_DEBUGPL(DBG_PCDV, "%s(%p) otg_dev %p\n", __func__, _dev, otg_dev);
-+
-+ /*
-+ * Free the IRQ
-+ */
-+#ifdef PLATFORM_INTERFACE
-+ free_irq(platform_get_irq(_dev, 0), pcd);
-+#else
-+ free_irq(_dev->irq, pcd);
-+#endif
-+ dwc_otg_pcd_remove(otg_dev->pcd);
-+ free_wrapper(gadget_wrapper);
-+ otg_dev->pcd = 0;
-+}
-+
-+#endif /* DWC_HOST_ONLY */
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_regs.h
-@@ -0,0 +1,2550 @@
-+/* ==========================================================================
-+ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_regs.h $
-+ * $Revision: #98 $
-+ * $Date: 2012/08/10 $
-+ * $Change: 2047372 $
-+ *
-+ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter,
-+ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless
-+ * otherwise expressly agreed to in writing between Synopsys and you.
-+ *
-+ * The Software IS NOT an item of Licensed Software or Licensed Product under
-+ * any End User Software License Agreement or Agreement for Licensed Product
-+ * with Synopsys or any supplement thereto. You are permitted to use and
-+ * redistribute this Software in source and binary forms, with or without
-+ * modification, provided that redistributions of source code must retain this
-+ * notice. You may not view, use, disclose, copy or distribute this file or
-+ * any information contained herein except pursuant to this license grant from
-+ * Synopsys. If you do not agree with this notice, including the disclaimer
-+ * below, then you are not authorized to use the Software.
-+ *
-+ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS
-+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
-+ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT,
-+ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
-+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
-+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
-+ * DAMAGE.
-+ * ========================================================================== */
-+
-+#ifndef __DWC_OTG_REGS_H__
-+#define __DWC_OTG_REGS_H__
-+
-+#include "dwc_otg_core_if.h"
-+
-+/**
-+ * @file
-+ *
-+ * This file contains the data structures for accessing the DWC_otg core registers.
-+ *
-+ * The application interfaces with the HS OTG core by reading from and
-+ * writing to the Control and Status Register (CSR) space through the
-+ * AHB Slave interface. These registers are 32 bits wide, and the
-+ * addresses are 32-bit-block aligned.
-+ * CSRs are classified as follows:
-+ * - Core Global Registers
-+ * - Device Mode Registers
-+ * - Device Global Registers
-+ * - Device Endpoint Specific Registers
-+ * - Host Mode Registers
-+ * - Host Global Registers
-+ * - Host Port CSRs
-+ * - Host Channel Specific Registers
-+ *
-+ * Only the Core Global registers can be accessed in both Device and
-+ * Host modes. When the HS OTG core is operating in one mode, either
-+ * Device or Host, the application must not access registers from the
-+ * other mode. When the core switches from one mode to another, the
-+ * registers in the new mode of operation must be reprogrammed as they
-+ * would be after a power-on reset.
-+ */
-+
-+/****************************************************************************/
-+/** DWC_otg Core registers .
-+ * The dwc_otg_core_global_regs structure defines the size
-+ * and relative field offsets for the Core Global registers.
-+ */
-+typedef struct dwc_otg_core_global_regs {
-+ /** OTG Control and Status Register. <i>Offset: 000h</i> */
-+ volatile uint32_t gotgctl;
-+ /** OTG Interrupt Register. <i>Offset: 004h</i> */
-+ volatile uint32_t gotgint;
-+ /**Core AHB Configuration Register. <i>Offset: 008h</i> */
-+ volatile uint32_t gahbcfg;
-+
-+#define DWC_GLBINTRMASK 0x0001
-+#define DWC_DMAENABLE 0x0020
-+#define DWC_NPTXEMPTYLVL_EMPTY 0x0080
-+#define DWC_NPTXEMPTYLVL_HALFEMPTY 0x0000
-+#define DWC_PTXEMPTYLVL_EMPTY 0x0100
-+#define DWC_PTXEMPTYLVL_HALFEMPTY 0x0000
-+
-+ /**Core USB Configuration Register. <i>Offset: 00Ch</i> */
-+ volatile uint32_t gusbcfg;
-+ /**Core Reset Register. <i>Offset: 010h</i> */
-+ volatile uint32_t grstctl;
-+ /**Core Interrupt Register. <i>Offset: 014h</i> */
-+ volatile uint32_t gintsts;
-+ /**Core Interrupt Mask Register. <i>Offset: 018h</i> */
-+ volatile uint32_t gintmsk;
-+ /**Receive Status Queue Read Register (Read Only). <i>Offset: 01Ch</i> */
-+ volatile uint32_t grxstsr;
-+ /**Receive Status Queue Read & POP Register (Read Only). <i>Offset: 020h</i>*/
-+ volatile uint32_t grxstsp;
-+ /**Receive FIFO Size Register. <i>Offset: 024h</i> */
-+ volatile uint32_t grxfsiz;
-+ /**Non Periodic Transmit FIFO Size Register. <i>Offset: 028h</i> */
-+ volatile uint32_t gnptxfsiz;
-+ /**Non Periodic Transmit FIFO/Queue Status Register (Read
-+ * Only). <i>Offset: 02Ch</i> */
-+ volatile uint32_t gnptxsts;
-+ /**I2C Access Register. <i>Offset: 030h</i> */
-+ volatile uint32_t gi2cctl;
-+ /**PHY Vendor Control Register. <i>Offset: 034h</i> */
-+ volatile uint32_t gpvndctl;
-+ /**General Purpose Input/Output Register. <i>Offset: 038h</i> */
-+ volatile uint32_t ggpio;
-+ /**User ID Register. <i>Offset: 03Ch</i> */
-+ volatile uint32_t guid;
-+ /**Synopsys ID Register (Read Only). <i>Offset: 040h</i> */
-+ volatile uint32_t gsnpsid;
-+ /**User HW Config1 Register (Read Only). <i>Offset: 044h</i> */
-+ volatile uint32_t ghwcfg1;
-+ /**User HW Config2 Register (Read Only). <i>Offset: 048h</i> */
-+ volatile uint32_t ghwcfg2;
-+#define DWC_SLAVE_ONLY_ARCH 0
-+#define DWC_EXT_DMA_ARCH 1
-+#define DWC_INT_DMA_ARCH 2
-+
-+#define DWC_MODE_HNP_SRP_CAPABLE 0
-+#define DWC_MODE_SRP_ONLY_CAPABLE 1
-+#define DWC_MODE_NO_HNP_SRP_CAPABLE 2
-+#define DWC_MODE_SRP_CAPABLE_DEVICE 3
-+#define DWC_MODE_NO_SRP_CAPABLE_DEVICE 4
-+#define DWC_MODE_SRP_CAPABLE_HOST 5
-+#define DWC_MODE_NO_SRP_CAPABLE_HOST 6
-+
-+ /**User HW Config3 Register (Read Only). <i>Offset: 04Ch</i> */
-+ volatile uint32_t ghwcfg3;
-+ /**User HW Config4 Register (Read Only). <i>Offset: 050h</i>*/
-+ volatile uint32_t ghwcfg4;
-+ /** Core LPM Configuration register <i>Offset: 054h</i>*/
-+ volatile uint32_t glpmcfg;
-+ /** Global PowerDn Register <i>Offset: 058h</i> */
-+ volatile uint32_t gpwrdn;
-+ /** Global DFIFO SW Config Register <i>Offset: 05Ch</i> */
-+ volatile uint32_t gdfifocfg;
-+ /** ADP Control Register <i>Offset: 060h</i> */
-+ volatile uint32_t adpctl;
-+ /** Reserved <i>Offset: 064h-0FFh</i> */
-+ volatile uint32_t reserved39[39];
-+ /** Host Periodic Transmit FIFO Size Register. <i>Offset: 100h</i> */
-+ volatile uint32_t hptxfsiz;
-+ /** Device Periodic Transmit FIFO#n Register if dedicated fifos are disabled,
-+ otherwise Device Transmit FIFO#n Register.
-+ * <i>Offset: 104h + (FIFO_Number-1)*04h, 1 <= FIFO Number <= 15 (1<=n<=15).</i> */
-+ volatile uint32_t dtxfsiz[15];
-+} dwc_otg_core_global_regs_t;
-+
-+/**
-+ * This union represents the bit fields of the Core OTG Control
-+ * and Status Register (GOTGCTL). Set the bits using the bit
-+ * fields then write the <i>d32</i> value to the register.
-+ */
-+typedef union gotgctl_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ unsigned sesreqscs:1;
-+ unsigned sesreq:1;
-+ unsigned vbvalidoven:1;
-+ unsigned vbvalidovval:1;
-+ unsigned avalidoven:1;
-+ unsigned avalidovval:1;
-+ unsigned bvalidoven:1;
-+ unsigned bvalidovval:1;
-+ unsigned hstnegscs:1;
-+ unsigned hnpreq:1;
-+ unsigned hstsethnpen:1;
-+ unsigned devhnpen:1;
-+ unsigned reserved12_15:4;
-+ unsigned conidsts:1;
-+ unsigned dbnctime:1;
-+ unsigned asesvld:1;
-+ unsigned bsesvld:1;
-+ unsigned otgver:1;
-+ unsigned reserved1:1;
-+ unsigned multvalidbc:5;
-+ unsigned chirpen:1;
-+ unsigned reserved28_31:4;
-+ } b;
-+} gotgctl_data_t;
-+
-+/**
-+ * This union represents the bit fields of the Core OTG Interrupt Register
-+ * (GOTGINT). Set/clear the bits using the bit fields then write the <i>d32</i>
-+ * value to the register.
-+ */
-+typedef union gotgint_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ /** Current Mode */
-+ unsigned reserved0_1:2;
-+
-+ /** Session End Detected */
-+ unsigned sesenddet:1;
-+
-+ unsigned reserved3_7:5;
-+
-+ /** Session Request Success Status Change */
-+ unsigned sesreqsucstschng:1;
-+ /** Host Negotiation Success Status Change */
-+ unsigned hstnegsucstschng:1;
-+
-+ unsigned reserved10_16:7;
-+
-+ /** Host Negotiation Detected */
-+ unsigned hstnegdet:1;
-+ /** A-Device Timeout Change */
-+ unsigned adevtoutchng:1;
-+ /** Debounce Done */
-+ unsigned debdone:1;
-+ /** Multi-Valued input changed */
-+ unsigned mvic:1;
-+
-+ unsigned reserved31_21:11;
-+
-+ } b;
-+} gotgint_data_t;
-+
-+/**
-+ * This union represents the bit fields of the Core AHB Configuration
-+ * Register (GAHBCFG). Set/clear the bits using the bit fields then
-+ * write the <i>d32</i> value to the register.
-+ */
-+typedef union gahbcfg_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ unsigned glblintrmsk:1;
-+#define DWC_GAHBCFG_GLBINT_ENABLE 1
-+
-+ unsigned hburstlen:4;
-+#define DWC_GAHBCFG_INT_DMA_BURST_SINGLE 0
-+#define DWC_GAHBCFG_INT_DMA_BURST_INCR 1
-+#define DWC_GAHBCFG_INT_DMA_BURST_INCR4 3
-+#define DWC_GAHBCFG_INT_DMA_BURST_INCR8 5
-+#define DWC_GAHBCFG_INT_DMA_BURST_INCR16 7
-+
-+ unsigned dmaenable:1;
-+#define DWC_GAHBCFG_DMAENABLE 1
-+ unsigned reserved:1;
-+ unsigned nptxfemplvl_txfemplvl:1;
-+ unsigned ptxfemplvl:1;
-+#define DWC_GAHBCFG_TXFEMPTYLVL_EMPTY 1
-+#define DWC_GAHBCFG_TXFEMPTYLVL_HALFEMPTY 0
-+ unsigned reserved9_20:12;
-+ unsigned remmemsupp:1;
-+ unsigned notialldmawrit:1;
-+ unsigned ahbsingle:1;
-+ unsigned reserved24_31:8;
-+ } b;
-+} gahbcfg_data_t;
-+
-+/**
-+ * This union represents the bit fields of the Core USB Configuration
-+ * Register (GUSBCFG). Set the bits using the bit fields then write
-+ * the <i>d32</i> value to the register.
-+ */
-+typedef union gusbcfg_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ unsigned toutcal:3;
-+ unsigned phyif:1;
-+ unsigned ulpi_utmi_sel:1;
-+ unsigned fsintf:1;
-+ unsigned physel:1;
-+ unsigned ddrsel:1;
-+ unsigned srpcap:1;
-+ unsigned hnpcap:1;
-+ unsigned usbtrdtim:4;
-+ unsigned reserved1:1;
-+ unsigned phylpwrclksel:1;
-+ unsigned otgutmifssel:1;
-+ unsigned ulpi_fsls:1;
-+ unsigned ulpi_auto_res:1;
-+ unsigned ulpi_clk_sus_m:1;
-+ unsigned ulpi_ext_vbus_drv:1;
-+ unsigned ulpi_int_vbus_indicator:1;
-+ unsigned term_sel_dl_pulse:1;
-+ unsigned indicator_complement:1;
-+ unsigned indicator_pass_through:1;
-+ unsigned ulpi_int_prot_dis:1;
-+ unsigned ic_usb_cap:1;
-+ unsigned ic_traffic_pull_remove:1;
-+ unsigned tx_end_delay:1;
-+ unsigned force_host_mode:1;
-+ unsigned force_dev_mode:1;
-+ unsigned reserved31:1;
-+ } b;
-+} gusbcfg_data_t;
-+
-+/**
-+ * This union represents the bit fields of the Core Reset Register
-+ * (GRSTCTL). Set/clear the bits using the bit fields then write the
-+ * <i>d32</i> value to the register.
-+ */
-+typedef union grstctl_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ /** Core Soft Reset (CSftRst) (Device and Host)
-+ *
-+ * The application can flush the control logic in the
-+ * entire core using this bit. This bit resets the
-+ * pipelines in the AHB Clock domain as well as the
-+ * PHY Clock domain.
-+ *
-+ * The state machines are reset to an IDLE state, the
-+ * control bits in the CSRs are cleared, all the
-+ * transmit FIFOs and the receive FIFO are flushed.
-+ *
-+ * The status mask bits that control the generation of
-+ * the interrupt, are cleared, to clear the
-+ * interrupt. The interrupt status bits are not
-+ * cleared, so the application can get the status of
-+ * any events that occurred in the core after it has
-+ * set this bit.
-+ *
-+ * Any transactions on the AHB are terminated as soon
-+ * as possible following the protocol. Any
-+ * transactions on the USB are terminated immediately.
-+ *
-+ * The configuration settings in the CSRs are
-+ * unchanged, so the software doesn't have to
-+ * reprogram these registers (Device
-+ * Configuration/Host Configuration/Core System
-+ * Configuration/Core PHY Configuration).
-+ *
-+ * The application can write to this bit, any time it
-+ * wants to reset the core. This is a self clearing
-+ * bit and the core clears this bit after all the
-+ * necessary logic is reset in the core, which may
-+ * take several clocks, depending on the current state
-+ * of the core.
-+ */
-+ unsigned csftrst:1;
-+ /** Hclk Soft Reset
-+ *
-+ * The application uses this bit to reset the control logic in
-+ * the AHB clock domain. Only AHB clock domain pipelines are
-+ * reset.
-+ */
-+ unsigned hsftrst:1;
-+ /** Host Frame Counter Reset (Host Only)<br>
-+ *
-+ * The application can reset the (micro)frame number
-+ * counter inside the core, using this bit. When the
-+ * (micro)frame counter is reset, the subsequent SOF
-+ * sent out by the core, will have a (micro)frame
-+ * number of 0.
-+ */
-+ unsigned hstfrm:1;
-+ /** In Token Sequence Learning Queue Flush
-+ * (INTknQFlsh) (Device Only)
-+ */
-+ unsigned intknqflsh:1;
-+ /** RxFIFO Flush (RxFFlsh) (Device and Host)
-+ *
-+ * The application can flush the entire Receive FIFO
-+ * using this bit. The application must first
-+ * ensure that the core is not in the middle of a
-+ * transaction. The application should write into
-+ * this bit, only after making sure that neither the
-+ * DMA engine is reading from the RxFIFO nor the MAC
-+ * is writing the data in to the FIFO. The
-+ * application should wait until the bit is cleared
-+ * before performing any other operations. This bit
-+ * will takes 8 clocks (slowest of PHY or AHB clock)
-+ * to clear.
-+ */
-+ unsigned rxfflsh:1;
-+ /** TxFIFO Flush (TxFFlsh) (Device and Host).
-+ *
-+ * This bit is used to selectively flush a single or
-+ * all transmit FIFOs. The application must first
-+ * ensure that the core is not in the middle of a
-+ * transaction. The application should write into
-+ * this bit, only after making sure that neither the
-+ * DMA engine is writing into the TxFIFO nor the MAC
-+ * is reading the data out of the FIFO. The
-+ * application should wait until the core clears this
-+ * bit, before performing any operations. This bit
-+ * will takes 8 clocks (slowest of PHY or AHB clock)
-+ * to clear.
-+ */
-+ unsigned txfflsh:1;
-+
-+ /** TxFIFO Number (TxFNum) (Device and Host).
-+ *
-+ * This is the FIFO number which needs to be flushed,
-+ * using the TxFIFO Flush bit. This field should not
-+ * be changed until the TxFIFO Flush bit is cleared by
-+ * the core.
-+ * - 0x0 : Non Periodic TxFIFO Flush
-+ * - 0x1 : Periodic TxFIFO #1 Flush in device mode
-+ * or Periodic TxFIFO in host mode
-+ * - 0x2 : Periodic TxFIFO #2 Flush in device mode.
-+ * - ...
-+ * - 0xF : Periodic TxFIFO #15 Flush in device mode
-+ * - 0x10: Flush all the Transmit NonPeriodic and
-+ * Transmit Periodic FIFOs in the core
-+ */
-+ unsigned txfnum:5;
-+ /** Reserved */
-+ unsigned reserved11_29:19;
-+ /** DMA Request Signal. Indicated DMA request is in
-+ * probress. Used for debug purpose. */
-+ unsigned dmareq:1;
-+ /** AHB Master Idle. Indicates the AHB Master State
-+ * Machine is in IDLE condition. */
-+ unsigned ahbidle:1;
-+ } b;
-+} grstctl_t;
-+
-+/**
-+ * This union represents the bit fields of the Core Interrupt Mask
-+ * Register (GINTMSK). Set/clear the bits using the bit fields then
-+ * write the <i>d32</i> value to the register.
-+ */
-+typedef union gintmsk_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ unsigned reserved0:1;
-+ unsigned modemismatch:1;
-+ unsigned otgintr:1;
-+ unsigned sofintr:1;
-+ unsigned rxstsqlvl:1;
-+ unsigned nptxfempty:1;
-+ unsigned ginnakeff:1;
-+ unsigned goutnakeff:1;
-+ unsigned ulpickint:1;
-+ unsigned i2cintr:1;
-+ unsigned erlysuspend:1;
-+ unsigned usbsuspend:1;
-+ unsigned usbreset:1;
-+ unsigned enumdone:1;
-+ unsigned isooutdrop:1;
-+ unsigned eopframe:1;
-+ unsigned restoredone:1;
-+ unsigned epmismatch:1;
-+ unsigned inepintr:1;
-+ unsigned outepintr:1;
-+ unsigned incomplisoin:1;
-+ unsigned incomplisoout:1;
-+ unsigned fetsusp:1;
-+ unsigned resetdet:1;
-+ unsigned portintr:1;
-+ unsigned hcintr:1;
-+ unsigned ptxfempty:1;
-+ unsigned lpmtranrcvd:1;
-+ unsigned conidstschng:1;
-+ unsigned disconnect:1;
-+ unsigned sessreqintr:1;
-+ unsigned wkupintr:1;
-+ } b;
-+} gintmsk_data_t;
-+/**
-+ * This union represents the bit fields of the Core Interrupt Register
-+ * (GINTSTS). Set/clear the bits using the bit fields then write the
-+ * <i>d32</i> value to the register.
-+ */
-+typedef union gintsts_data {
-+ /** raw register data */
-+ uint32_t d32;
-+#define DWC_SOF_INTR_MASK 0x0008
-+ /** register bits */
-+ struct {
-+#define DWC_HOST_MODE 1
-+ unsigned curmode:1;
-+ unsigned modemismatch:1;
-+ unsigned otgintr:1;
-+ unsigned sofintr:1;
-+ unsigned rxstsqlvl:1;
-+ unsigned nptxfempty:1;
-+ unsigned ginnakeff:1;
-+ unsigned goutnakeff:1;
-+ unsigned ulpickint:1;
-+ unsigned i2cintr:1;
-+ unsigned erlysuspend:1;
-+ unsigned usbsuspend:1;
-+ unsigned usbreset:1;
-+ unsigned enumdone:1;
-+ unsigned isooutdrop:1;
-+ unsigned eopframe:1;
-+ unsigned restoredone:1;
-+ unsigned epmismatch:1;
-+ unsigned inepint:1;
-+ unsigned outepintr:1;
-+ unsigned incomplisoin:1;
-+ unsigned incomplisoout:1;
-+ unsigned fetsusp:1;
-+ unsigned resetdet:1;
-+ unsigned portintr:1;
-+ unsigned hcintr:1;
-+ unsigned ptxfempty:1;
-+ unsigned lpmtranrcvd:1;
-+ unsigned conidstschng:1;
-+ unsigned disconnect:1;
-+ unsigned sessreqintr:1;
-+ unsigned wkupintr:1;
-+ } b;
-+} gintsts_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Device Receive Status Read and
-+ * Pop Registers (GRXSTSR, GRXSTSP) Read the register into the <i>d32</i>
-+ * element then read out the bits using the <i>b</i>it elements.
-+ */
-+typedef union device_grxsts_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ unsigned epnum:4;
-+ unsigned bcnt:11;
-+ unsigned dpid:2;
-+
-+#define DWC_STS_DATA_UPDT 0x2 // OUT Data Packet
-+#define DWC_STS_XFER_COMP 0x3 // OUT Data Transfer Complete
-+
-+#define DWC_DSTS_GOUT_NAK 0x1 // Global OUT NAK
-+#define DWC_DSTS_SETUP_COMP 0x4 // Setup Phase Complete
-+#define DWC_DSTS_SETUP_UPDT 0x6 // SETUP Packet
-+ unsigned pktsts:4;
-+ unsigned fn:4;
-+ unsigned reserved25_31:7;
-+ } b;
-+} device_grxsts_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Host Receive Status Read and
-+ * Pop Registers (GRXSTSR, GRXSTSP) Read the register into the <i>d32</i>
-+ * element then read out the bits using the <i>b</i>it elements.
-+ */
-+typedef union host_grxsts_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ unsigned chnum:4;
-+ unsigned bcnt:11;
-+ unsigned dpid:2;
-+
-+ unsigned pktsts:4;
-+#define DWC_GRXSTS_PKTSTS_IN 0x2
-+#define DWC_GRXSTS_PKTSTS_IN_XFER_COMP 0x3
-+#define DWC_GRXSTS_PKTSTS_DATA_TOGGLE_ERR 0x5
-+#define DWC_GRXSTS_PKTSTS_CH_HALTED 0x7
-+
-+ unsigned reserved21_31:11;
-+ } b;
-+} host_grxsts_data_t;
-+
-+/**
-+ * This union represents the bit fields in the FIFO Size Registers (HPTXFSIZ,
-+ * GNPTXFSIZ, DPTXFSIZn, DIEPTXFn). Read the register into the <i>d32</i> element
-+ * then read out the bits using the <i>b</i>it elements.
-+ */
-+typedef union fifosize_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ unsigned startaddr:16;
-+ unsigned depth:16;
-+ } b;
-+} fifosize_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Non-Periodic Transmit
-+ * FIFO/Queue Status Register (GNPTXSTS). Read the register into the
-+ * <i>d32</i> element then read out the bits using the <i>b</i>it
-+ * elements.
-+ */
-+typedef union gnptxsts_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ unsigned nptxfspcavail:16;
-+ unsigned nptxqspcavail:8;
-+ /** Top of the Non-Periodic Transmit Request Queue
-+ * - bit 24 - Terminate (Last entry for the selected
-+ * channel/EP)
-+ * - bits 26:25 - Token Type
-+ * - 2'b00 - IN/OUT
-+ * - 2'b01 - Zero Length OUT
-+ * - 2'b10 - PING/Complete Split
-+ * - 2'b11 - Channel Halt
-+ * - bits 30:27 - Channel/EP Number
-+ */
-+ unsigned nptxqtop_terminate:1;
-+ unsigned nptxqtop_token:2;
-+ unsigned nptxqtop_chnep:4;
-+ unsigned reserved:1;
-+ } b;
-+} gnptxsts_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Transmit
-+ * FIFO Status Register (DTXFSTS). Read the register into the
-+ * <i>d32</i> element then read out the bits using the <i>b</i>it
-+ * elements.
-+ */
-+typedef union dtxfsts_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ unsigned txfspcavail:16;
-+ unsigned reserved:16;
-+ } b;
-+} dtxfsts_data_t;
-+
-+/**
-+ * This union represents the bit fields in the I2C Control Register
-+ * (I2CCTL). Read the register into the <i>d32</i> element then read out the
-+ * bits using the <i>b</i>it elements.
-+ */
-+typedef union gi2cctl_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ unsigned rwdata:8;
-+ unsigned regaddr:8;
-+ unsigned addr:7;
-+ unsigned i2cen:1;
-+ unsigned ack:1;
-+ unsigned i2csuspctl:1;
-+ unsigned i2cdevaddr:2;
-+ unsigned i2cdatse0:1;
-+ unsigned reserved:1;
-+ unsigned rw:1;
-+ unsigned bsydne:1;
-+ } b;
-+} gi2cctl_data_t;
-+
-+/**
-+ * This union represents the bit fields in the PHY Vendor Control Register
-+ * (GPVNDCTL). Read the register into the <i>d32</i> element then read out the
-+ * bits using the <i>b</i>it elements.
-+ */
-+typedef union gpvndctl_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ unsigned regdata:8;
-+ unsigned vctrl:8;
-+ unsigned regaddr16_21:6;
-+ unsigned regwr:1;
-+ unsigned reserved23_24:2;
-+ unsigned newregreq:1;
-+ unsigned vstsbsy:1;
-+ unsigned vstsdone:1;
-+ unsigned reserved28_30:3;
-+ unsigned disulpidrvr:1;
-+ } b;
-+} gpvndctl_data_t;
-+
-+/**
-+ * This union represents the bit fields in the General Purpose
-+ * Input/Output Register (GGPIO).
-+ * Read the register into the <i>d32</i> element then read out the
-+ * bits using the <i>b</i>it elements.
-+ */
-+typedef union ggpio_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ unsigned gpi:16;
-+ unsigned gpo:16;
-+ } b;
-+} ggpio_data_t;
-+
-+/**
-+ * This union represents the bit fields in the User ID Register
-+ * (GUID). Read the register into the <i>d32</i> element then read out the
-+ * bits using the <i>b</i>it elements.
-+ */
-+typedef union guid_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ unsigned rwdata:32;
-+ } b;
-+} guid_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Synopsys ID Register
-+ * (GSNPSID). Read the register into the <i>d32</i> element then read out the
-+ * bits using the <i>b</i>it elements.
-+ */
-+typedef union gsnpsid_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ unsigned rwdata:32;
-+ } b;
-+} gsnpsid_data_t;
-+
-+/**
-+ * This union represents the bit fields in the User HW Config1
-+ * Register. Read the register into the <i>d32</i> element then read
-+ * out the bits using the <i>b</i>it elements.
-+ */
-+typedef union hwcfg1_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ unsigned ep_dir0:2;
-+ unsigned ep_dir1:2;
-+ unsigned ep_dir2:2;
-+ unsigned ep_dir3:2;
-+ unsigned ep_dir4:2;
-+ unsigned ep_dir5:2;
-+ unsigned ep_dir6:2;
-+ unsigned ep_dir7:2;
-+ unsigned ep_dir8:2;
-+ unsigned ep_dir9:2;
-+ unsigned ep_dir10:2;
-+ unsigned ep_dir11:2;
-+ unsigned ep_dir12:2;
-+ unsigned ep_dir13:2;
-+ unsigned ep_dir14:2;
-+ unsigned ep_dir15:2;
-+ } b;
-+} hwcfg1_data_t;
-+
-+/**
-+ * This union represents the bit fields in the User HW Config2
-+ * Register. Read the register into the <i>d32</i> element then read
-+ * out the bits using the <i>b</i>it elements.
-+ */
-+typedef union hwcfg2_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ /* GHWCFG2 */
-+ unsigned op_mode:3;
-+#define DWC_HWCFG2_OP_MODE_HNP_SRP_CAPABLE_OTG 0
-+#define DWC_HWCFG2_OP_MODE_SRP_ONLY_CAPABLE_OTG 1
-+#define DWC_HWCFG2_OP_MODE_NO_HNP_SRP_CAPABLE_OTG 2
-+#define DWC_HWCFG2_OP_MODE_SRP_CAPABLE_DEVICE 3
-+#define DWC_HWCFG2_OP_MODE_NO_SRP_CAPABLE_DEVICE 4
-+#define DWC_HWCFG2_OP_MODE_SRP_CAPABLE_HOST 5
-+#define DWC_HWCFG2_OP_MODE_NO_SRP_CAPABLE_HOST 6
-+
-+ unsigned architecture:2;
-+ unsigned point2point:1;
-+ unsigned hs_phy_type:2;
-+#define DWC_HWCFG2_HS_PHY_TYPE_NOT_SUPPORTED 0
-+#define DWC_HWCFG2_HS_PHY_TYPE_UTMI 1
-+#define DWC_HWCFG2_HS_PHY_TYPE_ULPI 2
-+#define DWC_HWCFG2_HS_PHY_TYPE_UTMI_ULPI 3
-+
-+ unsigned fs_phy_type:2;
-+ unsigned num_dev_ep:4;
-+ unsigned num_host_chan:4;
-+ unsigned perio_ep_supported:1;
-+ unsigned dynamic_fifo:1;
-+ unsigned multi_proc_int:1;
-+ unsigned reserved21:1;
-+ unsigned nonperio_tx_q_depth:2;
-+ unsigned host_perio_tx_q_depth:2;
-+ unsigned dev_token_q_depth:5;
-+ unsigned otg_enable_ic_usb:1;
-+ } b;
-+} hwcfg2_data_t;
-+
-+/**
-+ * This union represents the bit fields in the User HW Config3
-+ * Register. Read the register into the <i>d32</i> element then read
-+ * out the bits using the <i>b</i>it elements.
-+ */
-+typedef union hwcfg3_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ /* GHWCFG3 */
-+ unsigned xfer_size_cntr_width:4;
-+ unsigned packet_size_cntr_width:3;
-+ unsigned otg_func:1;
-+ unsigned i2c:1;
-+ unsigned vendor_ctrl_if:1;
-+ unsigned optional_features:1;
-+ unsigned synch_reset_type:1;
-+ unsigned adp_supp:1;
-+ unsigned otg_enable_hsic:1;
-+ unsigned bc_support:1;
-+ unsigned otg_lpm_en:1;
-+ unsigned dfifo_depth:16;
-+ } b;
-+} hwcfg3_data_t;
-+
-+/**
-+ * This union represents the bit fields in the User HW Config4
-+ * Register. Read the register into the <i>d32</i> element then read
-+ * out the bits using the <i>b</i>it elements.
-+ */
-+typedef union hwcfg4_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ unsigned num_dev_perio_in_ep:4;
-+ unsigned power_optimiz:1;
-+ unsigned min_ahb_freq:1;
-+ unsigned hiber:1;
-+ unsigned xhiber:1;
-+ unsigned reserved:6;
-+ unsigned utmi_phy_data_width:2;
-+ unsigned num_dev_mode_ctrl_ep:4;
-+ unsigned iddig_filt_en:1;
-+ unsigned vbus_valid_filt_en:1;
-+ unsigned a_valid_filt_en:1;
-+ unsigned b_valid_filt_en:1;
-+ unsigned session_end_filt_en:1;
-+ unsigned ded_fifo_en:1;
-+ unsigned num_in_eps:4;
-+ unsigned desc_dma:1;
-+ unsigned desc_dma_dyn:1;
-+ } b;
-+} hwcfg4_data_t;
-+
-+/**
-+ * This union represents the bit fields of the Core LPM Configuration
-+ * Register (GLPMCFG). Set the bits using bit fields then write
-+ * the <i>d32</i> value to the register.
-+ */
-+typedef union glpmctl_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ /** LPM-Capable (LPMCap) (Device and Host)
-+ * The application uses this bit to control
-+ * the DWC_otg core LPM capabilities.
-+ */
-+ unsigned lpm_cap_en:1;
-+ /** LPM response programmed by application (AppL1Res) (Device)
-+ * Handshake response to LPM token pre-programmed
-+ * by device application software.
-+ */
-+ unsigned appl_resp:1;
-+ /** Host Initiated Resume Duration (HIRD) (Device and Host)
-+ * In Host mode this field indicates the value of HIRD
-+ * to be sent in an LPM transaction.
-+ * In Device mode this field is updated with the
-+ * Received LPM Token HIRD bmAttribute
-+ * when an ACK/NYET/STALL response is sent
-+ * to an LPM transaction.
-+ */
-+ unsigned hird:4;
-+ /** RemoteWakeEnable (bRemoteWake) (Device and Host)
-+ * In Host mode this bit indicates the value of remote
-+ * wake up to be sent in wIndex field of LPM transaction.
-+ * In Device mode this field is updated with the
-+ * Received LPM Token bRemoteWake bmAttribute
-+ * when an ACK/NYET/STALL response is sent
-+ * to an LPM transaction.
-+ */
-+ unsigned rem_wkup_en:1;
-+ /** Enable utmi_sleep_n (EnblSlpM) (Device and Host)
-+ * The application uses this bit to control
-+ * the utmi_sleep_n assertion to the PHY when in L1 state.
-+ */
-+ unsigned en_utmi_sleep:1;
-+ /** HIRD Threshold (HIRD_Thres) (Device and Host)
-+ */
-+ unsigned hird_thres:5;
-+ /** LPM Response (CoreL1Res) (Device and Host)
-+ * In Host mode this bit contains handsake response to
-+ * LPM transaction.
-+ * In Device mode the response of the core to
-+ * LPM transaction received is reflected in these two bits.
-+ - 0x0 : ERROR (No handshake response)
-+ - 0x1 : STALL
-+ - 0x2 : NYET
-+ - 0x3 : ACK
-+ */
-+ unsigned lpm_resp:2;
-+ /** Port Sleep Status (SlpSts) (Device and Host)
-+ * This bit is set as long as a Sleep condition
-+ * is present on the USB bus.
-+ */
-+ unsigned prt_sleep_sts:1;
-+ /** Sleep State Resume OK (L1ResumeOK) (Device and Host)
-+ * Indicates that the application or host
-+ * can start resume from Sleep state.
-+ */
-+ unsigned sleep_state_resumeok:1;
-+ /** LPM channel Index (LPM_Chnl_Indx) (Host)
-+ * The channel number on which the LPM transaction
-+ * has to be applied while sending
-+ * an LPM transaction to the local device.
-+ */
-+ unsigned lpm_chan_index:4;
-+ /** LPM Retry Count (LPM_Retry_Cnt) (Host)
-+ * Number host retries that would be performed
-+ * if the device response was not valid response.
-+ */
-+ unsigned retry_count:3;
-+ /** Send LPM Transaction (SndLPM) (Host)
-+ * When set by application software,
-+ * an LPM transaction containing two tokens
-+ * is sent.
-+ */
-+ unsigned send_lpm:1;
-+ /** LPM Retry status (LPM_RetryCnt_Sts) (Host)
-+ * Number of LPM Host Retries still remaining
-+ * to be transmitted for the current LPM sequence
-+ */
-+ unsigned retry_count_sts:3;
-+ unsigned reserved28_29:2;
-+ /** In host mode once this bit is set, the host
-+ * configures to drive the HSIC Idle state on the bus.
-+ * It then waits for the device to initiate the Connect sequence.
-+ * In device mode once this bit is set, the device waits for
-+ * the HSIC Idle line state on the bus. Upon receving the Idle
-+ * line state, it initiates the HSIC Connect sequence.
-+ */
-+ unsigned hsic_connect:1;
-+ /** This bit overrides and functionally inverts
-+ * the if_select_hsic input port signal.
-+ */
-+ unsigned inv_sel_hsic:1;
-+ } b;
-+} glpmcfg_data_t;
-+
-+/**
-+ * This union represents the bit fields of the Core ADP Timer, Control and
-+ * Status Register (ADPTIMCTLSTS). Set the bits using bit fields then write
-+ * the <i>d32</i> value to the register.
-+ */
-+typedef union adpctl_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ /** Probe Discharge (PRB_DSCHG)
-+ * These bits set the times for TADP_DSCHG.
-+ * These bits are defined as follows:
-+ * 2'b00 - 4 msec
-+ * 2'b01 - 8 msec
-+ * 2'b10 - 16 msec
-+ * 2'b11 - 32 msec
-+ */
-+ unsigned prb_dschg:2;
-+ /** Probe Delta (PRB_DELTA)
-+ * These bits set the resolution for RTIM value.
-+ * The bits are defined in units of 32 kHz clock cycles as follows:
-+ * 2'b00 - 1 cycles
-+ * 2'b01 - 2 cycles
-+ * 2'b10 - 3 cycles
-+ * 2'b11 - 4 cycles
-+ * For example if this value is chosen to 2'b01, it means that RTIM
-+ * increments for every 3(three) 32Khz clock cycles.
-+ */
-+ unsigned prb_delta:2;
-+ /** Probe Period (PRB_PER)
-+ * These bits sets the TADP_PRD as shown in Figure 4 as follows:
-+ * 2'b00 - 0.625 to 0.925 sec (typical 0.775 sec)
-+ * 2'b01 - 1.25 to 1.85 sec (typical 1.55 sec)
-+ * 2'b10 - 1.9 to 2.6 sec (typical 2.275 sec)
-+ * 2'b11 - Reserved
-+ */
-+ unsigned prb_per:2;
-+ /** These bits capture the latest time it took for VBUS to ramp from
-+ * VADP_SINK to VADP_PRB.
-+ * 0x000 - 1 cycles
-+ * 0x001 - 2 cycles
-+ * 0x002 - 3 cycles
-+ * etc
-+ * 0x7FF - 2048 cycles
-+ * A time of 1024 cycles at 32 kHz corresponds to a time of 32 msec.
-+ */
-+ unsigned rtim:11;
-+ /** Enable Probe (EnaPrb)
-+ * When programmed to 1'b1, the core performs a probe operation.
-+ * This bit is valid only if OTG_Ver = 1'b1.
-+ */
-+ unsigned enaprb:1;
-+ /** Enable Sense (EnaSns)
-+ * When programmed to 1'b1, the core performs a Sense operation.
-+ * This bit is valid only if OTG_Ver = 1'b1.
-+ */
-+ unsigned enasns:1;
-+ /** ADP Reset (ADPRes)
-+ * When set, ADP controller is reset.
-+ * This bit is valid only if OTG_Ver = 1'b1.
-+ */
-+ unsigned adpres:1;
-+ /** ADP Enable (ADPEn)
-+ * When set, the core performs either ADP probing or sensing
-+ * based on EnaPrb or EnaSns.
-+ * This bit is valid only if OTG_Ver = 1'b1.
-+ */
-+ unsigned adpen:1;
-+ /** ADP Probe Interrupt (ADP_PRB_INT)
-+ * When this bit is set, it means that the VBUS
-+ * voltage is greater than VADP_PRB or VADP_PRB is reached.
-+ * This bit is valid only if OTG_Ver = 1'b1.
-+ */
-+ unsigned adp_prb_int:1;
-+ /**
-+ * ADP Sense Interrupt (ADP_SNS_INT)
-+ * When this bit is set, it means that the VBUS voltage is greater than
-+ * VADP_SNS value or VADP_SNS is reached.
-+ * This bit is valid only if OTG_Ver = 1'b1.
-+ */
-+ unsigned adp_sns_int:1;
-+ /** ADP Tomeout Interrupt (ADP_TMOUT_INT)
-+ * This bit is relevant only for an ADP probe.
-+ * When this bit is set, it means that the ramp time has
-+ * completed ie ADPCTL.RTIM has reached its terminal value
-+ * of 0x7FF. This is a debug feature that allows software
-+ * to read the ramp time after each cycle.
-+ * This bit is valid only if OTG_Ver = 1'b1.
-+ */
-+ unsigned adp_tmout_int:1;
-+ /** ADP Probe Interrupt Mask (ADP_PRB_INT_MSK)
-+ * When this bit is set, it unmasks the interrupt due to ADP_PRB_INT.
-+ * This bit is valid only if OTG_Ver = 1'b1.
-+ */
-+ unsigned adp_prb_int_msk:1;
-+ /** ADP Sense Interrupt Mask (ADP_SNS_INT_MSK)
-+ * When this bit is set, it unmasks the interrupt due to ADP_SNS_INT.
-+ * This bit is valid only if OTG_Ver = 1'b1.
-+ */
-+ unsigned adp_sns_int_msk:1;
-+ /** ADP Timoeout Interrupt Mask (ADP_TMOUT_MSK)
-+ * When this bit is set, it unmasks the interrupt due to ADP_TMOUT_INT.
-+ * This bit is valid only if OTG_Ver = 1'b1.
-+ */
-+ unsigned adp_tmout_int_msk:1;
-+ /** Access Request
-+ * 2'b00 - Read/Write Valid (updated by the core)
-+ * 2'b01 - Read
-+ * 2'b00 - Write
-+ * 2'b00 - Reserved
-+ */
-+ unsigned ar:2;
-+ /** Reserved */
-+ unsigned reserved29_31:3;
-+ } b;
-+} adpctl_data_t;
-+
-+////////////////////////////////////////////
-+// Device Registers
-+/**
-+ * Device Global Registers. <i>Offsets 800h-BFFh</i>
-+ *
-+ * The following structures define the size and relative field offsets
-+ * for the Device Mode Registers.
-+ *
-+ * <i>These registers are visible only in Device mode and must not be
-+ * accessed in Host mode, as the results are unknown.</i>
-+ */
-+typedef struct dwc_otg_dev_global_regs {
-+ /** Device Configuration Register. <i>Offset 800h</i> */
-+ volatile uint32_t dcfg;
-+ /** Device Control Register. <i>Offset: 804h</i> */
-+ volatile uint32_t dctl;
-+ /** Device Status Register (Read Only). <i>Offset: 808h</i> */
-+ volatile uint32_t dsts;
-+ /** Reserved. <i>Offset: 80Ch</i> */
-+ uint32_t unused;
-+ /** Device IN Endpoint Common Interrupt Mask
-+ * Register. <i>Offset: 810h</i> */
-+ volatile uint32_t diepmsk;
-+ /** Device OUT Endpoint Common Interrupt Mask
-+ * Register. <i>Offset: 814h</i> */
-+ volatile uint32_t doepmsk;
-+ /** Device All Endpoints Interrupt Register. <i>Offset: 818h</i> */
-+ volatile uint32_t daint;
-+ /** Device All Endpoints Interrupt Mask Register. <i>Offset:
-+ * 81Ch</i> */
-+ volatile uint32_t daintmsk;
-+ /** Device IN Token Queue Read Register-1 (Read Only).
-+ * <i>Offset: 820h</i> */
-+ volatile uint32_t dtknqr1;
-+ /** Device IN Token Queue Read Register-2 (Read Only).
-+ * <i>Offset: 824h</i> */
-+ volatile uint32_t dtknqr2;
-+ /** Device VBUS discharge Register. <i>Offset: 828h</i> */
-+ volatile uint32_t dvbusdis;
-+ /** Device VBUS Pulse Register. <i>Offset: 82Ch</i> */
-+ volatile uint32_t dvbuspulse;
-+ /** Device IN Token Queue Read Register-3 (Read Only). /
-+ * Device Thresholding control register (Read/Write)
-+ * <i>Offset: 830h</i> */
-+ volatile uint32_t dtknqr3_dthrctl;
-+ /** Device IN Token Queue Read Register-4 (Read Only). /
-+ * Device IN EPs empty Inr. Mask Register (Read/Write)
-+ * <i>Offset: 834h</i> */
-+ volatile uint32_t dtknqr4_fifoemptymsk;
-+ /** Device Each Endpoint Interrupt Register (Read Only). /
-+ * <i>Offset: 838h</i> */
-+ volatile uint32_t deachint;
-+ /** Device Each Endpoint Interrupt mask Register (Read/Write). /
-+ * <i>Offset: 83Ch</i> */
-+ volatile uint32_t deachintmsk;
-+ /** Device Each In Endpoint Interrupt mask Register (Read/Write). /
-+ * <i>Offset: 840h</i> */
-+ volatile uint32_t diepeachintmsk[MAX_EPS_CHANNELS];
-+ /** Device Each Out Endpoint Interrupt mask Register (Read/Write). /
-+ * <i>Offset: 880h</i> */
-+ volatile uint32_t doepeachintmsk[MAX_EPS_CHANNELS];
-+} dwc_otg_device_global_regs_t;
-+
-+/**
-+ * This union represents the bit fields in the Device Configuration
-+ * Register. Read the register into the <i>d32</i> member then
-+ * set/clear the bits using the <i>b</i>it elements. Write the
-+ * <i>d32</i> member to the dcfg register.
-+ */
-+typedef union dcfg_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ /** Device Speed */
-+ unsigned devspd:2;
-+ /** Non Zero Length Status OUT Handshake */
-+ unsigned nzstsouthshk:1;
-+#define DWC_DCFG_SEND_STALL 1
-+
-+ unsigned ena32khzs:1;
-+ /** Device Addresses */
-+ unsigned devaddr:7;
-+ /** Periodic Frame Interval */
-+ unsigned perfrint:2;
-+#define DWC_DCFG_FRAME_INTERVAL_80 0
-+#define DWC_DCFG_FRAME_INTERVAL_85 1
-+#define DWC_DCFG_FRAME_INTERVAL_90 2
-+#define DWC_DCFG_FRAME_INTERVAL_95 3
-+
-+ /** Enable Device OUT NAK for bulk in DDMA mode */
-+ unsigned endevoutnak:1;
-+
-+ unsigned reserved14_17:4;
-+ /** In Endpoint Mis-match count */
-+ unsigned epmscnt:5;
-+ /** Enable Descriptor DMA in Device mode */
-+ unsigned descdma:1;
-+ unsigned perschintvl:2;
-+ unsigned resvalid:6;
-+ } b;
-+} dcfg_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Device Control
-+ * Register. Read the register into the <i>d32</i> member then
-+ * set/clear the bits using the <i>b</i>it elements.
-+ */
-+typedef union dctl_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ /** Remote Wakeup */
-+ unsigned rmtwkupsig:1;
-+ /** Soft Disconnect */
-+ unsigned sftdiscon:1;
-+ /** Global Non-Periodic IN NAK Status */
-+ unsigned gnpinnaksts:1;
-+ /** Global OUT NAK Status */
-+ unsigned goutnaksts:1;
-+ /** Test Control */
-+ unsigned tstctl:3;
-+ /** Set Global Non-Periodic IN NAK */
-+ unsigned sgnpinnak:1;
-+ /** Clear Global Non-Periodic IN NAK */
-+ unsigned cgnpinnak:1;
-+ /** Set Global OUT NAK */
-+ unsigned sgoutnak:1;
-+ /** Clear Global OUT NAK */
-+ unsigned cgoutnak:1;
-+ /** Power-On Programming Done */
-+ unsigned pwronprgdone:1;
-+ /** Reserved */
-+ unsigned reserved:1;
-+ /** Global Multi Count */
-+ unsigned gmc:2;
-+ /** Ignore Frame Number for ISOC EPs */
-+ unsigned ifrmnum:1;
-+ /** NAK on Babble */
-+ unsigned nakonbble:1;
-+ /** Enable Continue on BNA */
-+ unsigned encontonbna:1;
-+
-+ unsigned reserved18_31:14;
-+ } b;
-+} dctl_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Device Status
-+ * Register. Read the register into the <i>d32</i> member then
-+ * set/clear the bits using the <i>b</i>it elements.
-+ */
-+typedef union dsts_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ /** Suspend Status */
-+ unsigned suspsts:1;
-+ /** Enumerated Speed */
-+ unsigned enumspd:2;
-+#define DWC_DSTS_ENUMSPD_HS_PHY_30MHZ_OR_60MHZ 0
-+#define DWC_DSTS_ENUMSPD_FS_PHY_30MHZ_OR_60MHZ 1
-+#define DWC_DSTS_ENUMSPD_LS_PHY_6MHZ 2
-+#define DWC_DSTS_ENUMSPD_FS_PHY_48MHZ 3
-+ /** Erratic Error */
-+ unsigned errticerr:1;
-+ unsigned reserved4_7:4;
-+ /** Frame or Microframe Number of the received SOF */
-+ unsigned soffn:14;
-+ unsigned reserved22_31:10;
-+ } b;
-+} dsts_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Device IN EP Interrupt
-+ * Register and the Device IN EP Common Mask Register.
-+ *
-+ * - Read the register into the <i>d32</i> member then set/clear the
-+ * bits using the <i>b</i>it elements.
-+ */
-+typedef union diepint_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ /** Transfer complete mask */
-+ unsigned xfercompl:1;
-+ /** Endpoint disable mask */
-+ unsigned epdisabled:1;
-+ /** AHB Error mask */
-+ unsigned ahberr:1;
-+ /** TimeOUT Handshake mask (non-ISOC EPs) */
-+ unsigned timeout:1;
-+ /** IN Token received with TxF Empty mask */
-+ unsigned intktxfemp:1;
-+ /** IN Token Received with EP mismatch mask */
-+ unsigned intknepmis:1;
-+ /** IN Endpoint NAK Effective mask */
-+ unsigned inepnakeff:1;
-+ /** Reserved */
-+ unsigned emptyintr:1;
-+
-+ unsigned txfifoundrn:1;
-+
-+ /** BNA Interrupt mask */
-+ unsigned bna:1;
-+
-+ unsigned reserved10_12:3;
-+ /** BNA Interrupt mask */
-+ unsigned nak:1;
-+
-+ unsigned reserved14_31:18;
-+ } b;
-+} diepint_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Device IN EP
-+ * Common/Dedicated Interrupt Mask Register.
-+ */
-+typedef union diepint_data diepmsk_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Device OUT EP Interrupt
-+ * Registerand Device OUT EP Common Interrupt Mask Register.
-+ *
-+ * - Read the register into the <i>d32</i> member then set/clear the
-+ * bits using the <i>b</i>it elements.
-+ */
-+typedef union doepint_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ /** Transfer complete */
-+ unsigned xfercompl:1;
-+ /** Endpoint disable */
-+ unsigned epdisabled:1;
-+ /** AHB Error */
-+ unsigned ahberr:1;
-+ /** Setup Phase Done (contorl EPs) */
-+ unsigned setup:1;
-+ /** OUT Token Received when Endpoint Disabled */
-+ unsigned outtknepdis:1;
-+
-+ unsigned stsphsercvd:1;
-+ /** Back-to-Back SETUP Packets Received */
-+ unsigned back2backsetup:1;
-+
-+ unsigned reserved7:1;
-+ /** OUT packet Error */
-+ unsigned outpkterr:1;
-+ /** BNA Interrupt */
-+ unsigned bna:1;
-+
-+ unsigned reserved10:1;
-+ /** Packet Drop Status */
-+ unsigned pktdrpsts:1;
-+ /** Babble Interrupt */
-+ unsigned babble:1;
-+ /** NAK Interrupt */
-+ unsigned nak:1;
-+ /** NYET Interrupt */
-+ unsigned nyet:1;
-+ /** Bit indicating setup packet received */
-+ unsigned sr:1;
-+
-+ unsigned reserved16_31:16;
-+ } b;
-+} doepint_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Device OUT EP
-+ * Common/Dedicated Interrupt Mask Register.
-+ */
-+typedef union doepint_data doepmsk_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Device All EP Interrupt
-+ * and Mask Registers.
-+ * - Read the register into the <i>d32</i> member then set/clear the
-+ * bits using the <i>b</i>it elements.
-+ */
-+typedef union daint_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ /** IN Endpoint bits */
-+ unsigned in:16;
-+ /** OUT Endpoint bits */
-+ unsigned out:16;
-+ } ep;
-+ struct {
-+ /** IN Endpoint bits */
-+ unsigned inep0:1;
-+ unsigned inep1:1;
-+ unsigned inep2:1;
-+ unsigned inep3:1;
-+ unsigned inep4:1;
-+ unsigned inep5:1;
-+ unsigned inep6:1;
-+ unsigned inep7:1;
-+ unsigned inep8:1;
-+ unsigned inep9:1;
-+ unsigned inep10:1;
-+ unsigned inep11:1;
-+ unsigned inep12:1;
-+ unsigned inep13:1;
-+ unsigned inep14:1;
-+ unsigned inep15:1;
-+ /** OUT Endpoint bits */
-+ unsigned outep0:1;
-+ unsigned outep1:1;
-+ unsigned outep2:1;
-+ unsigned outep3:1;
-+ unsigned outep4:1;
-+ unsigned outep5:1;
-+ unsigned outep6:1;
-+ unsigned outep7:1;
-+ unsigned outep8:1;
-+ unsigned outep9:1;
-+ unsigned outep10:1;
-+ unsigned outep11:1;
-+ unsigned outep12:1;
-+ unsigned outep13:1;
-+ unsigned outep14:1;
-+ unsigned outep15:1;
-+ } b;
-+} daint_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Device IN Token Queue
-+ * Read Registers.
-+ * - Read the register into the <i>d32</i> member.
-+ * - READ-ONLY Register
-+ */
-+typedef union dtknq1_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ /** In Token Queue Write Pointer */
-+ unsigned intknwptr:5;
-+ /** Reserved */
-+ unsigned reserved05_06:2;
-+ /** write pointer has wrapped. */
-+ unsigned wrap_bit:1;
-+ /** EP Numbers of IN Tokens 0 ... 4 */
-+ unsigned epnums0_5:24;
-+ } b;
-+} dtknq1_data_t;
-+
-+/**
-+ * This union represents Threshold control Register
-+ * - Read and write the register into the <i>d32</i> member.
-+ * - READ-WRITABLE Register
-+ */
-+typedef union dthrctl_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ /** non ISO Tx Thr. Enable */
-+ unsigned non_iso_thr_en:1;
-+ /** ISO Tx Thr. Enable */
-+ unsigned iso_thr_en:1;
-+ /** Tx Thr. Length */
-+ unsigned tx_thr_len:9;
-+ /** AHB Threshold ratio */
-+ unsigned ahb_thr_ratio:2;
-+ /** Reserved */
-+ unsigned reserved13_15:3;
-+ /** Rx Thr. Enable */
-+ unsigned rx_thr_en:1;
-+ /** Rx Thr. Length */
-+ unsigned rx_thr_len:9;
-+ unsigned reserved26:1;
-+ /** Arbiter Parking Enable*/
-+ unsigned arbprken:1;
-+ /** Reserved */
-+ unsigned reserved28_31:4;
-+ } b;
-+} dthrctl_data_t;
-+
-+/**
-+ * Device Logical IN Endpoint-Specific Registers. <i>Offsets
-+ * 900h-AFCh</i>
-+ *
-+ * There will be one set of endpoint registers per logical endpoint
-+ * implemented.
-+ *
-+ * <i>These registers are visible only in Device mode and must not be
-+ * accessed in Host mode, as the results are unknown.</i>
-+ */
-+typedef struct dwc_otg_dev_in_ep_regs {
-+ /** Device IN Endpoint Control Register. <i>Offset:900h +
-+ * (ep_num * 20h) + 00h</i> */
-+ volatile uint32_t diepctl;
-+ /** Reserved. <i>Offset:900h + (ep_num * 20h) + 04h</i> */
-+ uint32_t reserved04;
-+ /** Device IN Endpoint Interrupt Register. <i>Offset:900h +
-+ * (ep_num * 20h) + 08h</i> */
-+ volatile uint32_t diepint;
-+ /** Reserved. <i>Offset:900h + (ep_num * 20h) + 0Ch</i> */
-+ uint32_t reserved0C;
-+ /** Device IN Endpoint Transfer Size
-+ * Register. <i>Offset:900h + (ep_num * 20h) + 10h</i> */
-+ volatile uint32_t dieptsiz;
-+ /** Device IN Endpoint DMA Address Register. <i>Offset:900h +
-+ * (ep_num * 20h) + 14h</i> */
-+ volatile uint32_t diepdma;
-+ /** Device IN Endpoint Transmit FIFO Status Register. <i>Offset:900h +
-+ * (ep_num * 20h) + 18h</i> */
-+ volatile uint32_t dtxfsts;
-+ /** Device IN Endpoint DMA Buffer Register. <i>Offset:900h +
-+ * (ep_num * 20h) + 1Ch</i> */
-+ volatile uint32_t diepdmab;
-+} dwc_otg_dev_in_ep_regs_t;
-+
-+/**
-+ * Device Logical OUT Endpoint-Specific Registers. <i>Offsets:
-+ * B00h-CFCh</i>
-+ *
-+ * There will be one set of endpoint registers per logical endpoint
-+ * implemented.
-+ *
-+ * <i>These registers are visible only in Device mode and must not be
-+ * accessed in Host mode, as the results are unknown.</i>
-+ */
-+typedef struct dwc_otg_dev_out_ep_regs {
-+ /** Device OUT Endpoint Control Register. <i>Offset:B00h +
-+ * (ep_num * 20h) + 00h</i> */
-+ volatile uint32_t doepctl;
-+ /** Reserved. <i>Offset:B00h + (ep_num * 20h) + 04h</i> */
-+ uint32_t reserved04;
-+ /** Device OUT Endpoint Interrupt Register. <i>Offset:B00h +
-+ * (ep_num * 20h) + 08h</i> */
-+ volatile uint32_t doepint;
-+ /** Reserved. <i>Offset:B00h + (ep_num * 20h) + 0Ch</i> */
-+ uint32_t reserved0C;
-+ /** Device OUT Endpoint Transfer Size Register. <i>Offset:
-+ * B00h + (ep_num * 20h) + 10h</i> */
-+ volatile uint32_t doeptsiz;
-+ /** Device OUT Endpoint DMA Address Register. <i>Offset:B00h
-+ * + (ep_num * 20h) + 14h</i> */
-+ volatile uint32_t doepdma;
-+ /** Reserved. <i>Offset:B00h + * (ep_num * 20h) + 18h</i> */
-+ uint32_t unused;
-+ /** Device OUT Endpoint DMA Buffer Register. <i>Offset:B00h
-+ * + (ep_num * 20h) + 1Ch</i> */
-+ uint32_t doepdmab;
-+} dwc_otg_dev_out_ep_regs_t;
-+
-+/**
-+ * This union represents the bit fields in the Device EP Control
-+ * Register. Read the register into the <i>d32</i> member then
-+ * set/clear the bits using the <i>b</i>it elements.
-+ */
-+typedef union depctl_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ /** Maximum Packet Size
-+ * IN/OUT EPn
-+ * IN/OUT EP0 - 2 bits
-+ * 2'b00: 64 Bytes
-+ * 2'b01: 32
-+ * 2'b10: 16
-+ * 2'b11: 8 */
-+ unsigned mps:11;
-+#define DWC_DEP0CTL_MPS_64 0
-+#define DWC_DEP0CTL_MPS_32 1
-+#define DWC_DEP0CTL_MPS_16 2
-+#define DWC_DEP0CTL_MPS_8 3
-+
-+ /** Next Endpoint
-+ * IN EPn/IN EP0
-+ * OUT EPn/OUT EP0 - reserved */
-+ unsigned nextep:4;
-+
-+ /** USB Active Endpoint */
-+ unsigned usbactep:1;
-+
-+ /** Endpoint DPID (INTR/Bulk IN and OUT endpoints)
-+ * This field contains the PID of the packet going to
-+ * be received or transmitted on this endpoint. The
-+ * application should program the PID of the first
-+ * packet going to be received or transmitted on this
-+ * endpoint , after the endpoint is
-+ * activated. Application use the SetD1PID and
-+ * SetD0PID fields of this register to program either
-+ * D0 or D1 PID.
-+ *
-+ * The encoding for this field is
-+ * - 0: D0
-+ * - 1: D1
-+ */
-+ unsigned dpid:1;
-+
-+ /** NAK Status */
-+ unsigned naksts:1;
-+
-+ /** Endpoint Type
-+ * 2'b00: Control
-+ * 2'b01: Isochronous
-+ * 2'b10: Bulk
-+ * 2'b11: Interrupt */
-+ unsigned eptype:2;
-+
-+ /** Snoop Mode
-+ * OUT EPn/OUT EP0
-+ * IN EPn/IN EP0 - reserved */
-+ unsigned snp:1;
-+
-+ /** Stall Handshake */
-+ unsigned stall:1;
-+
-+ /** Tx Fifo Number
-+ * IN EPn/IN EP0
-+ * OUT EPn/OUT EP0 - reserved */
-+ unsigned txfnum:4;
-+
-+ /** Clear NAK */
-+ unsigned cnak:1;
-+ /** Set NAK */
-+ unsigned snak:1;
-+ /** Set DATA0 PID (INTR/Bulk IN and OUT endpoints)
-+ * Writing to this field sets the Endpoint DPID (DPID)
-+ * field in this register to DATA0. Set Even
-+ * (micro)frame (SetEvenFr) (ISO IN and OUT Endpoints)
-+ * Writing to this field sets the Even/Odd
-+ * (micro)frame (EO_FrNum) field to even (micro)
-+ * frame.
-+ */
-+ unsigned setd0pid:1;
-+ /** Set DATA1 PID (INTR/Bulk IN and OUT endpoints)
-+ * Writing to this field sets the Endpoint DPID (DPID)
-+ * field in this register to DATA1 Set Odd
-+ * (micro)frame (SetOddFr) (ISO IN and OUT Endpoints)
-+ * Writing to this field sets the Even/Odd
-+ * (micro)frame (EO_FrNum) field to odd (micro) frame.
-+ */
-+ unsigned setd1pid:1;
-+
-+ /** Endpoint Disable */
-+ unsigned epdis:1;
-+ /** Endpoint Enable */
-+ unsigned epena:1;
-+ } b;
-+} depctl_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Device EP Transfer
-+ * Size Register. Read the register into the <i>d32</i> member then
-+ * set/clear the bits using the <i>b</i>it elements.
-+ */
-+typedef union deptsiz_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ /** Transfer size */
-+ unsigned xfersize:19;
-+/** Max packet count for EP (pow(2,10)-1) */
-+#define MAX_PKT_CNT 1023
-+ /** Packet Count */
-+ unsigned pktcnt:10;
-+ /** Multi Count - Periodic IN endpoints */
-+ unsigned mc:2;
-+ unsigned reserved:1;
-+ } b;
-+} deptsiz_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Device EP 0 Transfer
-+ * Size Register. Read the register into the <i>d32</i> member then
-+ * set/clear the bits using the <i>b</i>it elements.
-+ */
-+typedef union deptsiz0_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ /** Transfer size */
-+ unsigned xfersize:7;
-+ /** Reserved */
-+ unsigned reserved7_18:12;
-+ /** Packet Count */
-+ unsigned pktcnt:2;
-+ /** Reserved */
-+ unsigned reserved21_28:8;
-+ /**Setup Packet Count (DOEPTSIZ0 Only) */
-+ unsigned supcnt:2;
-+ unsigned reserved31;
-+ } b;
-+} deptsiz0_data_t;
-+
-+/////////////////////////////////////////////////
-+// DMA Descriptor Specific Structures
-+//
-+
-+/** Buffer status definitions */
-+
-+#define BS_HOST_READY 0x0
-+#define BS_DMA_BUSY 0x1
-+#define BS_DMA_DONE 0x2
-+#define BS_HOST_BUSY 0x3
-+
-+/** Receive/Transmit status definitions */
-+
-+#define RTS_SUCCESS 0x0
-+#define RTS_BUFFLUSH 0x1
-+#define RTS_RESERVED 0x2
-+#define RTS_BUFERR 0x3
-+
-+/**
-+ * This union represents the bit fields in the DMA Descriptor
-+ * status quadlet. Read the quadlet into the <i>d32</i> member then
-+ * set/clear the bits using the <i>b</i>it, <i>b_iso_out</i> and
-+ * <i>b_iso_in</i> elements.
-+ */
-+typedef union dev_dma_desc_sts {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** quadlet bits */
-+ struct {
-+ /** Received number of bytes */
-+ unsigned bytes:16;
-+ /** NAK bit - only for OUT EPs */
-+ unsigned nak:1;
-+ unsigned reserved17_22:6;
-+ /** Multiple Transfer - only for OUT EPs */
-+ unsigned mtrf:1;
-+ /** Setup Packet received - only for OUT EPs */
-+ unsigned sr:1;
-+ /** Interrupt On Complete */
-+ unsigned ioc:1;
-+ /** Short Packet */
-+ unsigned sp:1;
-+ /** Last */
-+ unsigned l:1;
-+ /** Receive Status */
-+ unsigned sts:2;
-+ /** Buffer Status */
-+ unsigned bs:2;
-+ } b;
-+
-+//#ifdef DWC_EN_ISOC
-+ /** iso out quadlet bits */
-+ struct {
-+ /** Received number of bytes */
-+ unsigned rxbytes:11;
-+
-+ unsigned reserved11:1;
-+ /** Frame Number */
-+ unsigned framenum:11;
-+ /** Received ISO Data PID */
-+ unsigned pid:2;
-+ /** Interrupt On Complete */
-+ unsigned ioc:1;
-+ /** Short Packet */
-+ unsigned sp:1;
-+ /** Last */
-+ unsigned l:1;
-+ /** Receive Status */
-+ unsigned rxsts:2;
-+ /** Buffer Status */
-+ unsigned bs:2;
-+ } b_iso_out;
-+
-+ /** iso in quadlet bits */
-+ struct {
-+ /** Transmited number of bytes */
-+ unsigned txbytes:12;
-+ /** Frame Number */
-+ unsigned framenum:11;
-+ /** Transmited ISO Data PID */
-+ unsigned pid:2;
-+ /** Interrupt On Complete */
-+ unsigned ioc:1;
-+ /** Short Packet */
-+ unsigned sp:1;
-+ /** Last */
-+ unsigned l:1;
-+ /** Transmit Status */
-+ unsigned txsts:2;
-+ /** Buffer Status */
-+ unsigned bs:2;
-+ } b_iso_in;
-+//#endif /* DWC_EN_ISOC */
-+} dev_dma_desc_sts_t;
-+
-+/**
-+ * DMA Descriptor structure
-+ *
-+ * DMA Descriptor structure contains two quadlets:
-+ * Status quadlet and Data buffer pointer.
-+ */
-+typedef struct dwc_otg_dev_dma_desc {
-+ /** DMA Descriptor status quadlet */
-+ dev_dma_desc_sts_t status;
-+ /** DMA Descriptor data buffer pointer */
-+ uint32_t buf;
-+} dwc_otg_dev_dma_desc_t;
-+
-+/**
-+ * The dwc_otg_dev_if structure contains information needed to manage
-+ * the DWC_otg controller acting in device mode. It represents the
-+ * programming view of the device-specific aspects of the controller.
-+ */
-+typedef struct dwc_otg_dev_if {
-+ /** Pointer to device Global registers.
-+ * Device Global Registers starting at offset 800h
-+ */
-+ dwc_otg_device_global_regs_t *dev_global_regs;
-+#define DWC_DEV_GLOBAL_REG_OFFSET 0x800
-+
-+ /**
-+ * Device Logical IN Endpoint-Specific Registers 900h-AFCh
-+ */
-+ dwc_otg_dev_in_ep_regs_t *in_ep_regs[MAX_EPS_CHANNELS];
-+#define DWC_DEV_IN_EP_REG_OFFSET 0x900
-+#define DWC_EP_REG_OFFSET 0x20
-+
-+ /** Device Logical OUT Endpoint-Specific Registers B00h-CFCh */
-+ dwc_otg_dev_out_ep_regs_t *out_ep_regs[MAX_EPS_CHANNELS];
-+#define DWC_DEV_OUT_EP_REG_OFFSET 0xB00
-+
-+ /* Device configuration information */
-+ uint8_t speed; /**< Device Speed 0: Unknown, 1: LS, 2:FS, 3: HS */
-+ uint8_t num_in_eps; /**< Number # of Tx EP range: 0-15 exept ep0 */
-+ uint8_t num_out_eps; /**< Number # of Rx EP range: 0-15 exept ep 0*/
-+
-+ /** Size of periodic FIFOs (Bytes) */
-+ uint16_t perio_tx_fifo_size[MAX_PERIO_FIFOS];
-+
-+ /** Size of Tx FIFOs (Bytes) */
-+ uint16_t tx_fifo_size[MAX_TX_FIFOS];
-+
-+ /** Thresholding enable flags and length varaiables **/
-+ uint16_t rx_thr_en;
-+ uint16_t iso_tx_thr_en;
-+ uint16_t non_iso_tx_thr_en;
-+
-+ uint16_t rx_thr_length;
-+ uint16_t tx_thr_length;
-+
-+ /**
-+ * Pointers to the DMA Descriptors for EP0 Control
-+ * transfers (virtual and physical)
-+ */
-+
-+ /** 2 descriptors for SETUP packets */
-+ dwc_dma_t dma_setup_desc_addr[2];
-+ dwc_otg_dev_dma_desc_t *setup_desc_addr[2];
-+
-+ /** Pointer to Descriptor with latest SETUP packet */
-+ dwc_otg_dev_dma_desc_t *psetup;
-+
-+ /** Index of current SETUP handler descriptor */
-+ uint32_t setup_desc_index;
-+
-+ /** Descriptor for Data In or Status In phases */
-+ dwc_dma_t dma_in_desc_addr;
-+ dwc_otg_dev_dma_desc_t *in_desc_addr;
-+
-+ /** Descriptor for Data Out or Status Out phases */
-+ dwc_dma_t dma_out_desc_addr;
-+ dwc_otg_dev_dma_desc_t *out_desc_addr;
-+
-+ /** Setup Packet Detected - if set clear NAK when queueing */
-+ uint32_t spd;
-+ /** Isoc ep pointer on which incomplete happens */
-+ void *isoc_ep;
-+
-+} dwc_otg_dev_if_t;
-+
-+/////////////////////////////////////////////////
-+// Host Mode Register Structures
-+//
-+/**
-+ * The Host Global Registers structure defines the size and relative
-+ * field offsets for the Host Mode Global Registers. Host Global
-+ * Registers offsets 400h-7FFh.
-+*/
-+typedef struct dwc_otg_host_global_regs {
-+ /** Host Configuration Register. <i>Offset: 400h</i> */
-+ volatile uint32_t hcfg;
-+ /** Host Frame Interval Register. <i>Offset: 404h</i> */
-+ volatile uint32_t hfir;
-+ /** Host Frame Number / Frame Remaining Register. <i>Offset: 408h</i> */
-+ volatile uint32_t hfnum;
-+ /** Reserved. <i>Offset: 40Ch</i> */
-+ uint32_t reserved40C;
-+ /** Host Periodic Transmit FIFO/ Queue Status Register. <i>Offset: 410h</i> */
-+ volatile uint32_t hptxsts;
-+ /** Host All Channels Interrupt Register. <i>Offset: 414h</i> */
-+ volatile uint32_t haint;
-+ /** Host All Channels Interrupt Mask Register. <i>Offset: 418h</i> */
-+ volatile uint32_t haintmsk;
-+ /** Host Frame List Base Address Register . <i>Offset: 41Ch</i> */
-+ volatile uint32_t hflbaddr;
-+} dwc_otg_host_global_regs_t;
-+
-+/**
-+ * This union represents the bit fields in the Host Configuration Register.
-+ * Read the register into the <i>d32</i> member then set/clear the bits using
-+ * the <i>b</i>it elements. Write the <i>d32</i> member to the hcfg register.
-+ */
-+typedef union hcfg_data {
-+ /** raw register data */
-+ uint32_t d32;
-+
-+ /** register bits */
-+ struct {
-+ /** FS/LS Phy Clock Select */
-+ unsigned fslspclksel:2;
-+#define DWC_HCFG_30_60_MHZ 0
-+#define DWC_HCFG_48_MHZ 1
-+#define DWC_HCFG_6_MHZ 2
-+
-+ /** FS/LS Only Support */
-+ unsigned fslssupp:1;
-+ unsigned reserved3_6:4;
-+ /** Enable 32-KHz Suspend Mode */
-+ unsigned ena32khzs:1;
-+ /** Resume Validation Periiod */
-+ unsigned resvalid:8;
-+ unsigned reserved16_22:7;
-+ /** Enable Scatter/gather DMA in Host mode */
-+ unsigned descdma:1;
-+ /** Frame List Entries */
-+ unsigned frlisten:2;
-+ /** Enable Periodic Scheduling */
-+ unsigned perschedena:1;
-+ unsigned reserved27_30:4;
-+ unsigned modechtimen:1;
-+ } b;
-+} hcfg_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Host Frame Remaing/Number
-+ * Register.
-+ */
-+typedef union hfir_data {
-+ /** raw register data */
-+ uint32_t d32;
-+
-+ /** register bits */
-+ struct {
-+ unsigned frint:16;
-+ unsigned hfirrldctrl:1;
-+ unsigned reserved:15;
-+ } b;
-+} hfir_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Host Frame Remaing/Number
-+ * Register.
-+ */
-+typedef union hfnum_data {
-+ /** raw register data */
-+ uint32_t d32;
-+
-+ /** register bits */
-+ struct {
-+ unsigned frnum:16;
-+#define DWC_HFNUM_MAX_FRNUM 0x3FFF
-+ unsigned frrem:16;
-+ } b;
-+} hfnum_data_t;
-+
-+typedef union hptxsts_data {
-+ /** raw register data */
-+ uint32_t d32;
-+
-+ /** register bits */
-+ struct {
-+ unsigned ptxfspcavail:16;
-+ unsigned ptxqspcavail:8;
-+ /** Top of the Periodic Transmit Request Queue
-+ * - bit 24 - Terminate (last entry for the selected channel)
-+ * - bits 26:25 - Token Type
-+ * - 2'b00 - Zero length
-+ * - 2'b01 - Ping
-+ * - 2'b10 - Disable
-+ * - bits 30:27 - Channel Number
-+ * - bit 31 - Odd/even microframe
-+ */
-+ unsigned ptxqtop_terminate:1;
-+ unsigned ptxqtop_token:2;
-+ unsigned ptxqtop_chnum:4;
-+ unsigned ptxqtop_odd:1;
-+ } b;
-+} hptxsts_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Host Port Control and Status
-+ * Register. Read the register into the <i>d32</i> member then set/clear the
-+ * bits using the <i>b</i>it elements. Write the <i>d32</i> member to the
-+ * hprt0 register.
-+ */
-+typedef union hprt0_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ unsigned prtconnsts:1;
-+ unsigned prtconndet:1;
-+ unsigned prtena:1;
-+ unsigned prtenchng:1;
-+ unsigned prtovrcurract:1;
-+ unsigned prtovrcurrchng:1;
-+ unsigned prtres:1;
-+ unsigned prtsusp:1;
-+ unsigned prtrst:1;
-+ unsigned reserved9:1;
-+ unsigned prtlnsts:2;
-+ unsigned prtpwr:1;
-+ unsigned prttstctl:4;
-+ unsigned prtspd:2;
-+#define DWC_HPRT0_PRTSPD_HIGH_SPEED 0
-+#define DWC_HPRT0_PRTSPD_FULL_SPEED 1
-+#define DWC_HPRT0_PRTSPD_LOW_SPEED 2
-+ unsigned reserved19_31:13;
-+ } b;
-+} hprt0_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Host All Interrupt
-+ * Register.
-+ */
-+typedef union haint_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ unsigned ch0:1;
-+ unsigned ch1:1;
-+ unsigned ch2:1;
-+ unsigned ch3:1;
-+ unsigned ch4:1;
-+ unsigned ch5:1;
-+ unsigned ch6:1;
-+ unsigned ch7:1;
-+ unsigned ch8:1;
-+ unsigned ch9:1;
-+ unsigned ch10:1;
-+ unsigned ch11:1;
-+ unsigned ch12:1;
-+ unsigned ch13:1;
-+ unsigned ch14:1;
-+ unsigned ch15:1;
-+ unsigned reserved:16;
-+ } b;
-+
-+ struct {
-+ unsigned chint:16;
-+ unsigned reserved:16;
-+ } b2;
-+} haint_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Host All Interrupt
-+ * Register.
-+ */
-+typedef union haintmsk_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ unsigned ch0:1;
-+ unsigned ch1:1;
-+ unsigned ch2:1;
-+ unsigned ch3:1;
-+ unsigned ch4:1;
-+ unsigned ch5:1;
-+ unsigned ch6:1;
-+ unsigned ch7:1;
-+ unsigned ch8:1;
-+ unsigned ch9:1;
-+ unsigned ch10:1;
-+ unsigned ch11:1;
-+ unsigned ch12:1;
-+ unsigned ch13:1;
-+ unsigned ch14:1;
-+ unsigned ch15:1;
-+ unsigned reserved:16;
-+ } b;
-+
-+ struct {
-+ unsigned chint:16;
-+ unsigned reserved:16;
-+ } b2;
-+} haintmsk_data_t;
-+
-+/**
-+ * Host Channel Specific Registers. <i>500h-5FCh</i>
-+ */
-+typedef struct dwc_otg_hc_regs {
-+ /** Host Channel 0 Characteristic Register. <i>Offset: 500h + (chan_num * 20h) + 00h</i> */
-+ volatile uint32_t hcchar;
-+ /** Host Channel 0 Split Control Register. <i>Offset: 500h + (chan_num * 20h) + 04h</i> */
-+ volatile uint32_t hcsplt;
-+ /** Host Channel 0 Interrupt Register. <i>Offset: 500h + (chan_num * 20h) + 08h</i> */
-+ volatile uint32_t hcint;
-+ /** Host Channel 0 Interrupt Mask Register. <i>Offset: 500h + (chan_num * 20h) + 0Ch</i> */
-+ volatile uint32_t hcintmsk;
-+ /** Host Channel 0 Transfer Size Register. <i>Offset: 500h + (chan_num * 20h) + 10h</i> */
-+ volatile uint32_t hctsiz;
-+ /** Host Channel 0 DMA Address Register. <i>Offset: 500h + (chan_num * 20h) + 14h</i> */
-+ volatile uint32_t hcdma;
-+ volatile uint32_t reserved;
-+ /** Host Channel 0 DMA Buffer Address Register. <i>Offset: 500h + (chan_num * 20h) + 1Ch</i> */
-+ volatile uint32_t hcdmab;
-+} dwc_otg_hc_regs_t;
-+
-+/**
-+ * This union represents the bit fields in the Host Channel Characteristics
-+ * Register. Read the register into the <i>d32</i> member then set/clear the
-+ * bits using the <i>b</i>it elements. Write the <i>d32</i> member to the
-+ * hcchar register.
-+ */
-+typedef union hcchar_data {
-+ /** raw register data */
-+ uint32_t d32;
-+
-+ /** register bits */
-+ struct {
-+ /** Maximum packet size in bytes */
-+ unsigned mps:11;
-+
-+ /** Endpoint number */
-+ unsigned epnum:4;
-+
-+ /** 0: OUT, 1: IN */
-+ unsigned epdir:1;
-+
-+ unsigned reserved:1;
-+
-+ /** 0: Full/high speed device, 1: Low speed device */
-+ unsigned lspddev:1;
-+
-+ /** 0: Control, 1: Isoc, 2: Bulk, 3: Intr */
-+ unsigned eptype:2;
-+
-+ /** Packets per frame for periodic transfers. 0 is reserved. */
-+ unsigned multicnt:2;
-+
-+ /** Device address */
-+ unsigned devaddr:7;
-+
-+ /**
-+ * Frame to transmit periodic transaction.
-+ * 0: even, 1: odd
-+ */
-+ unsigned oddfrm:1;
-+
-+ /** Channel disable */
-+ unsigned chdis:1;
-+
-+ /** Channel enable */
-+ unsigned chen:1;
-+ } b;
-+} hcchar_data_t;
-+
-+typedef union hcsplt_data {
-+ /** raw register data */
-+ uint32_t d32;
-+
-+ /** register bits */
-+ struct {
-+ /** Port Address */
-+ unsigned prtaddr:7;
-+
-+ /** Hub Address */
-+ unsigned hubaddr:7;
-+
-+ /** Transaction Position */
-+ unsigned xactpos:2;
-+#define DWC_HCSPLIT_XACTPOS_MID 0
-+#define DWC_HCSPLIT_XACTPOS_END 1
-+#define DWC_HCSPLIT_XACTPOS_BEGIN 2
-+#define DWC_HCSPLIT_XACTPOS_ALL 3
-+
-+ /** Do Complete Split */
-+ unsigned compsplt:1;
-+
-+ /** Reserved */
-+ unsigned reserved:14;
-+
-+ /** Split Enble */
-+ unsigned spltena:1;
-+ } b;
-+} hcsplt_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Host All Interrupt
-+ * Register.
-+ */
-+typedef union hcint_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ /** Transfer Complete */
-+ unsigned xfercomp:1;
-+ /** Channel Halted */
-+ unsigned chhltd:1;
-+ /** AHB Error */
-+ unsigned ahberr:1;
-+ /** STALL Response Received */
-+ unsigned stall:1;
-+ /** NAK Response Received */
-+ unsigned nak:1;
-+ /** ACK Response Received */
-+ unsigned ack:1;
-+ /** NYET Response Received */
-+ unsigned nyet:1;
-+ /** Transaction Err */
-+ unsigned xacterr:1;
-+ /** Babble Error */
-+ unsigned bblerr:1;
-+ /** Frame Overrun */
-+ unsigned frmovrun:1;
-+ /** Data Toggle Error */
-+ unsigned datatglerr:1;
-+ /** Buffer Not Available (only for DDMA mode) */
-+ unsigned bna:1;
-+ /** Exessive transaction error (only for DDMA mode) */
-+ unsigned xcs_xact:1;
-+ /** Frame List Rollover interrupt */
-+ unsigned frm_list_roll:1;
-+ /** Reserved */
-+ unsigned reserved14_31:18;
-+ } b;
-+} hcint_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Host Channel Interrupt Mask
-+ * Register. Read the register into the <i>d32</i> member then set/clear the
-+ * bits using the <i>b</i>it elements. Write the <i>d32</i> member to the
-+ * hcintmsk register.
-+ */
-+typedef union hcintmsk_data {
-+ /** raw register data */
-+ uint32_t d32;
-+
-+ /** register bits */
-+ struct {
-+ unsigned xfercompl:1;
-+ unsigned chhltd:1;
-+ unsigned ahberr:1;
-+ unsigned stall:1;
-+ unsigned nak:1;
-+ unsigned ack:1;
-+ unsigned nyet:1;
-+ unsigned xacterr:1;
-+ unsigned bblerr:1;
-+ unsigned frmovrun:1;
-+ unsigned datatglerr:1;
-+ unsigned bna:1;
-+ unsigned xcs_xact:1;
-+ unsigned frm_list_roll:1;
-+ unsigned reserved14_31:18;
-+ } b;
-+} hcintmsk_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Host Channel Transfer Size
-+ * Register. Read the register into the <i>d32</i> member then set/clear the
-+ * bits using the <i>b</i>it elements. Write the <i>d32</i> member to the
-+ * hcchar register.
-+ */
-+
-+typedef union hctsiz_data {
-+ /** raw register data */
-+ uint32_t d32;
-+
-+ /** register bits */
-+ struct {
-+ /** Total transfer size in bytes */
-+ unsigned xfersize:19;
-+
-+ /** Data packets to transfer */
-+ unsigned pktcnt:10;
-+
-+ /**
-+ * Packet ID for next data packet
-+ * 0: DATA0
-+ * 1: DATA2
-+ * 2: DATA1
-+ * 3: MDATA (non-Control), SETUP (Control)
-+ */
-+ unsigned pid:2;
-+#define DWC_HCTSIZ_DATA0 0
-+#define DWC_HCTSIZ_DATA1 2
-+#define DWC_HCTSIZ_DATA2 1
-+#define DWC_HCTSIZ_MDATA 3
-+#define DWC_HCTSIZ_SETUP 3
-+
-+ /** Do PING protocol when 1 */
-+ unsigned dopng:1;
-+ } b;
-+
-+ /** register bits */
-+ struct {
-+ /** Scheduling information */
-+ unsigned schinfo:8;
-+
-+ /** Number of transfer descriptors.
-+ * Max value:
-+ * 64 in general,
-+ * 256 only for HS isochronous endpoint.
-+ */
-+ unsigned ntd:8;
-+
-+ /** Data packets to transfer */
-+ unsigned reserved16_28:13;
-+
-+ /**
-+ * Packet ID for next data packet
-+ * 0: DATA0
-+ * 1: DATA2
-+ * 2: DATA1
-+ * 3: MDATA (non-Control)
-+ */
-+ unsigned pid:2;
-+
-+ /** Do PING protocol when 1 */
-+ unsigned dopng:1;
-+ } b_ddma;
-+} hctsiz_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Host DMA Address
-+ * Register used in Descriptor DMA mode.
-+ */
-+typedef union hcdma_data {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ unsigned reserved0_2:3;
-+ /** Current Transfer Descriptor. Not used for ISOC */
-+ unsigned ctd:8;
-+ /** Start Address of Descriptor List */
-+ unsigned dma_addr:21;
-+ } b;
-+} hcdma_data_t;
-+
-+/**
-+ * This union represents the bit fields in the DMA Descriptor
-+ * status quadlet for host mode. Read the quadlet into the <i>d32</i> member then
-+ * set/clear the bits using the <i>b</i>it elements.
-+ */
-+typedef union host_dma_desc_sts {
-+ /** raw register data */
-+ uint32_t d32;
-+ /** quadlet bits */
-+
-+ /* for non-isochronous */
-+ struct {
-+ /** Number of bytes */
-+ unsigned n_bytes:17;
-+ /** QTD offset to jump when Short Packet received - only for IN EPs */
-+ unsigned qtd_offset:6;
-+ /**
-+ * Set to request the core to jump to alternate QTD if
-+ * Short Packet received - only for IN EPs
-+ */
-+ unsigned a_qtd:1;
-+ /**
-+ * Setup Packet bit. When set indicates that buffer contains
-+ * setup packet.
-+ */
-+ unsigned sup:1;
-+ /** Interrupt On Complete */
-+ unsigned ioc:1;
-+ /** End of List */
-+ unsigned eol:1;
-+ unsigned reserved27:1;
-+ /** Rx/Tx Status */
-+ unsigned sts:2;
-+#define DMA_DESC_STS_PKTERR 1
-+ unsigned reserved30:1;
-+ /** Active Bit */
-+ unsigned a:1;
-+ } b;
-+ /* for isochronous */
-+ struct {
-+ /** Number of bytes */
-+ unsigned n_bytes:12;
-+ unsigned reserved12_24:13;
-+ /** Interrupt On Complete */
-+ unsigned ioc:1;
-+ unsigned reserved26_27:2;
-+ /** Rx/Tx Status */
-+ unsigned sts:2;
-+ unsigned reserved30:1;
-+ /** Active Bit */
-+ unsigned a:1;
-+ } b_isoc;
-+} host_dma_desc_sts_t;
-+
-+#define MAX_DMA_DESC_SIZE 131071
-+#define MAX_DMA_DESC_NUM_GENERIC 64
-+#define MAX_DMA_DESC_NUM_HS_ISOC 256
-+#define MAX_FRLIST_EN_NUM 64
-+/**
-+ * Host-mode DMA Descriptor structure
-+ *
-+ * DMA Descriptor structure contains two quadlets:
-+ * Status quadlet and Data buffer pointer.
-+ */
-+typedef struct dwc_otg_host_dma_desc {
-+ /** DMA Descriptor status quadlet */
-+ host_dma_desc_sts_t status;
-+ /** DMA Descriptor data buffer pointer */
-+ uint32_t buf;
-+} dwc_otg_host_dma_desc_t;
-+
-+/** OTG Host Interface Structure.
-+ *
-+ * The OTG Host Interface Structure structure contains information
-+ * needed to manage the DWC_otg controller acting in host mode. It
-+ * represents the programming view of the host-specific aspects of the
-+ * controller.
-+ */
-+typedef struct dwc_otg_host_if {
-+ /** Host Global Registers starting at offset 400h.*/
-+ dwc_otg_host_global_regs_t *host_global_regs;
-+#define DWC_OTG_HOST_GLOBAL_REG_OFFSET 0x400
-+
-+ /** Host Port 0 Control and Status Register */
-+ volatile uint32_t *hprt0;
-+#define DWC_OTG_HOST_PORT_REGS_OFFSET 0x440
-+
-+ /** Host Channel Specific Registers at offsets 500h-5FCh. */
-+ dwc_otg_hc_regs_t *hc_regs[MAX_EPS_CHANNELS];
-+#define DWC_OTG_HOST_CHAN_REGS_OFFSET 0x500
-+#define DWC_OTG_CHAN_REGS_OFFSET 0x20
-+
-+ /* Host configuration information */
-+ /** Number of Host Channels (range: 1-16) */
-+ uint8_t num_host_channels;
-+ /** Periodic EPs supported (0: no, 1: yes) */
-+ uint8_t perio_eps_supported;
-+ /** Periodic Tx FIFO Size (Only 1 host periodic Tx FIFO) */
-+ uint16_t perio_tx_fifo_size;
-+
-+} dwc_otg_host_if_t;
-+
-+/**
-+ * This union represents the bit fields in the Power and Clock Gating Control
-+ * Register. Read the register into the <i>d32</i> member then set/clear the
-+ * bits using the <i>b</i>it elements.
-+ */
-+typedef union pcgcctl_data {
-+ /** raw register data */
-+ uint32_t d32;
-+
-+ /** register bits */
-+ struct {
-+ /** Stop Pclk */
-+ unsigned stoppclk:1;
-+ /** Gate Hclk */
-+ unsigned gatehclk:1;
-+ /** Power Clamp */
-+ unsigned pwrclmp:1;
-+ /** Reset Power Down Modules */
-+ unsigned rstpdwnmodule:1;
-+ /** Reserved */
-+ unsigned reserved:1;
-+ /** Enable Sleep Clock Gating (Enbl_L1Gating) */
-+ unsigned enbl_sleep_gating:1;
-+ /** PHY In Sleep (PhySleep) */
-+ unsigned phy_in_sleep:1;
-+ /** Deep Sleep*/
-+ unsigned deep_sleep:1;
-+ unsigned resetaftsusp:1;
-+ unsigned restoremode:1;
-+ unsigned enbl_extnd_hiber:1;
-+ unsigned extnd_hiber_pwrclmp:1;
-+ unsigned extnd_hiber_switch:1;
-+ unsigned ess_reg_restored:1;
-+ unsigned prt_clk_sel:2;
-+ unsigned port_power:1;
-+ unsigned max_xcvrselect:2;
-+ unsigned max_termsel:1;
-+ unsigned mac_dev_addr:7;
-+ unsigned p2hd_dev_enum_spd:2;
-+ unsigned p2hd_prt_spd:2;
-+ unsigned if_dev_mode:1;
-+ } b;
-+} pcgcctl_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Global Data FIFO Software
-+ * Configuration Register. Read the register into the <i>d32</i> member then
-+ * set/clear the bits using the <i>b</i>it elements.
-+ */
-+typedef union gdfifocfg_data {
-+ /* raw register data */
-+ uint32_t d32;
-+ /** register bits */
-+ struct {
-+ /** OTG Data FIFO depth */
-+ unsigned gdfifocfg:16;
-+ /** Start address of EP info controller */
-+ unsigned epinfobase:16;
-+ } b;
-+} gdfifocfg_data_t;
-+
-+/**
-+ * This union represents the bit fields in the Global Power Down Register
-+ * Register. Read the register into the <i>d32</i> member then set/clear the
-+ * bits using the <i>b</i>it elements.
-+ */
-+typedef union gpwrdn_data {
-+ /* raw register data */
-+ uint32_t d32;
-+
-+ /** register bits */
-+ struct {
-+ /** PMU Interrupt Select */
-+ unsigned pmuintsel:1;
-+ /** PMU Active */
-+ unsigned pmuactv:1;
-+ /** Restore */
-+ unsigned restore:1;
-+ /** Power Down Clamp */
-+ unsigned pwrdnclmp:1;
-+ /** Power Down Reset */
-+ unsigned pwrdnrstn:1;
-+ /** Power Down Switch */
-+ unsigned pwrdnswtch:1;
-+ /** Disable VBUS */
-+ unsigned dis_vbus:1;
-+ /** Line State Change */
-+ unsigned lnstschng:1;
-+ /** Line state change mask */
-+ unsigned lnstchng_msk:1;
-+ /** Reset Detected */
-+ unsigned rst_det:1;
-+ /** Reset Detect mask */
-+ unsigned rst_det_msk:1;
-+ /** Disconnect Detected */
-+ unsigned disconn_det:1;
-+ /** Disconnect Detect mask */
-+ unsigned disconn_det_msk:1;
-+ /** Connect Detected*/
-+ unsigned connect_det:1;
-+ /** Connect Detected Mask*/
-+ unsigned connect_det_msk:1;
-+ /** SRP Detected */
-+ unsigned srp_det:1;
-+ /** SRP Detect mask */
-+ unsigned srp_det_msk:1;
-+ /** Status Change Interrupt */
-+ unsigned sts_chngint:1;
-+ /** Status Change Interrupt Mask */
-+ unsigned sts_chngint_msk:1;
-+ /** Line State */
-+ unsigned linestate:2;
-+ /** Indicates current mode(status of IDDIG signal) */
-+ unsigned idsts:1;
-+ /** B Session Valid signal status*/
-+ unsigned bsessvld:1;
-+ /** ADP Event Detected */
-+ unsigned adp_int:1;
-+ /** Multi Valued ID pin */
-+ unsigned mult_val_id_bc:5;
-+ /** Reserved 24_31 */
-+ unsigned reserved29_31:3;
-+ } b;
-+} gpwrdn_data_t;
-+
-+#endif
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/test/Makefile
-@@ -0,0 +1,16 @@
-+
-+PERL=/usr/bin/perl
-+PL_TESTS=test_sysfs.pl test_mod_param.pl
-+
-+.PHONY : test
-+test : perl_tests
-+
-+perl_tests :
-+ @echo
-+ @echo Running perl tests
-+ @for test in $(PL_TESTS); do \
-+ if $(PERL) ./$$test ; then \
-+ echo "=======> $$test, PASSED" ; \
-+ else echo "=======> $$test, FAILED" ; \
-+ fi \
-+ done
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/test/dwc_otg_test.pm
-@@ -0,0 +1,337 @@
-+package dwc_otg_test;
-+
-+use strict;
-+use Exporter ();
-+
-+use vars qw(@ISA @EXPORT
-+$sysfsdir $paramdir $errors $params
-+);
-+
-+ at ISA = qw(Exporter);
-+
-+#
-+# Globals
-+#
-+$sysfsdir = "/sys/devices/lm0";
-+$paramdir = "/sys/module/dwc_otg";
-+$errors = 0;
-+
-+$params = [
-+ {
-+ NAME => "otg_cap",
-+ DEFAULT => 0,
-+ ENUM => [],
-+ LOW => 0,
-+ HIGH => 2
-+ },
-+ {
-+ NAME => "dma_enable",
-+ DEFAULT => 0,
-+ ENUM => [],
-+ LOW => 0,
-+ HIGH => 1
-+ },
-+ {
-+ NAME => "dma_burst_size",
-+ DEFAULT => 32,
-+ ENUM => [1, 4, 8, 16, 32, 64, 128, 256],
-+ LOW => 1,
-+ HIGH => 256
-+ },
-+ {
-+ NAME => "host_speed",
-+ DEFAULT => 0,
-+ ENUM => [],
-+ LOW => 0,
-+ HIGH => 1
-+ },
-+ {
-+ NAME => "host_support_fs_ls_low_power",
-+ DEFAULT => 0,
-+ ENUM => [],
-+ LOW => 0,
-+ HIGH => 1
-+ },
-+ {
-+ NAME => "host_ls_low_power_phy_clk",
-+ DEFAULT => 0,
-+ ENUM => [],
-+ LOW => 0,
-+ HIGH => 1
-+ },
-+ {
-+ NAME => "dev_speed",
-+ DEFAULT => 0,
-+ ENUM => [],
-+ LOW => 0,
-+ HIGH => 1
-+ },
-+ {
-+ NAME => "enable_dynamic_fifo",
-+ DEFAULT => 1,
-+ ENUM => [],
-+ LOW => 0,
-+ HIGH => 1
-+ },
-+ {
-+ NAME => "data_fifo_size",
-+ DEFAULT => 8192,
-+ ENUM => [],
-+ LOW => 32,
-+ HIGH => 32768
-+ },
-+ {
-+ NAME => "dev_rx_fifo_size",
-+ DEFAULT => 1064,
-+ ENUM => [],
-+ LOW => 16,
-+ HIGH => 32768
-+ },
-+ {
-+ NAME => "dev_nperio_tx_fifo_size",
-+ DEFAULT => 1024,
-+ ENUM => [],
-+ LOW => 16,
-+ HIGH => 32768
-+ },
-+ {
-+ NAME => "dev_perio_tx_fifo_size_1",
-+ DEFAULT => 256,
-+ ENUM => [],
-+ LOW => 4,
-+ HIGH => 768
-+ },
-+ {
-+ NAME => "dev_perio_tx_fifo_size_2",
-+ DEFAULT => 256,
-+ ENUM => [],
-+ LOW => 4,
-+ HIGH => 768
-+ },
-+ {
-+ NAME => "dev_perio_tx_fifo_size_3",
-+ DEFAULT => 256,
-+ ENUM => [],
-+ LOW => 4,
-+ HIGH => 768
-+ },
-+ {
-+ NAME => "dev_perio_tx_fifo_size_4",
-+ DEFAULT => 256,
-+ ENUM => [],
-+ LOW => 4,
-+ HIGH => 768
-+ },
-+ {
-+ NAME => "dev_perio_tx_fifo_size_5",
-+ DEFAULT => 256,
-+ ENUM => [],
-+ LOW => 4,
-+ HIGH => 768
-+ },
-+ {
-+ NAME => "dev_perio_tx_fifo_size_6",
-+ DEFAULT => 256,
-+ ENUM => [],
-+ LOW => 4,
-+ HIGH => 768
-+ },
-+ {
-+ NAME => "dev_perio_tx_fifo_size_7",
-+ DEFAULT => 256,
-+ ENUM => [],
-+ LOW => 4,
-+ HIGH => 768
-+ },
-+ {
-+ NAME => "dev_perio_tx_fifo_size_8",
-+ DEFAULT => 256,
-+ ENUM => [],
-+ LOW => 4,
-+ HIGH => 768
-+ },
-+ {
-+ NAME => "dev_perio_tx_fifo_size_9",
-+ DEFAULT => 256,
-+ ENUM => [],
-+ LOW => 4,
-+ HIGH => 768
-+ },
-+ {
-+ NAME => "dev_perio_tx_fifo_size_10",
-+ DEFAULT => 256,
-+ ENUM => [],
-+ LOW => 4,
-+ HIGH => 768
-+ },
-+ {
-+ NAME => "dev_perio_tx_fifo_size_11",
-+ DEFAULT => 256,
-+ ENUM => [],
-+ LOW => 4,
-+ HIGH => 768
-+ },
-+ {
-+ NAME => "dev_perio_tx_fifo_size_12",
-+ DEFAULT => 256,
-+ ENUM => [],
-+ LOW => 4,
-+ HIGH => 768
-+ },
-+ {
-+ NAME => "dev_perio_tx_fifo_size_13",
-+ DEFAULT => 256,
-+ ENUM => [],
-+ LOW => 4,
-+ HIGH => 768
-+ },
-+ {
-+ NAME => "dev_perio_tx_fifo_size_14",
-+ DEFAULT => 256,
-+ ENUM => [],
-+ LOW => 4,
-+ HIGH => 768
-+ },
-+ {
-+ NAME => "dev_perio_tx_fifo_size_15",
-+ DEFAULT => 256,
-+ ENUM => [],
-+ LOW => 4,
-+ HIGH => 768
-+ },
-+ {
-+ NAME => "host_rx_fifo_size",
-+ DEFAULT => 1024,
-+ ENUM => [],
-+ LOW => 16,
-+ HIGH => 32768
-+ },
-+ {
-+ NAME => "host_nperio_tx_fifo_size",
-+ DEFAULT => 1024,
-+ ENUM => [],
-+ LOW => 16,
-+ HIGH => 32768
-+ },
-+ {
-+ NAME => "host_perio_tx_fifo_size",
-+ DEFAULT => 1024,
-+ ENUM => [],
-+ LOW => 16,
-+ HIGH => 32768
-+ },
-+ {
-+ NAME => "max_transfer_size",
-+ DEFAULT => 65535,
-+ ENUM => [],
-+ LOW => 2047,
-+ HIGH => 65535
-+ },
-+ {
-+ NAME => "max_packet_count",
-+ DEFAULT => 511,
-+ ENUM => [],
-+ LOW => 15,
-+ HIGH => 511
-+ },
-+ {
-+ NAME => "host_channels",
-+ DEFAULT => 12,
-+ ENUM => [],
-+ LOW => 1,
-+ HIGH => 16
-+ },
-+ {
-+ NAME => "dev_endpoints",
-+ DEFAULT => 6,
-+ ENUM => [],
-+ LOW => 1,
-+ HIGH => 15
-+ },
-+ {
-+ NAME => "phy_type",
-+ DEFAULT => 1,
-+ ENUM => [],
-+ LOW => 0,
-+ HIGH => 2
-+ },
-+ {
-+ NAME => "phy_utmi_width",
-+ DEFAULT => 16,
-+ ENUM => [8, 16],
-+ LOW => 8,
-+ HIGH => 16
-+ },
-+ {
-+ NAME => "phy_ulpi_ddr",
-+ DEFAULT => 0,
-+ ENUM => [],
-+ LOW => 0,
-+ HIGH => 1
-+ },
-+ ];
-+
-+
-+#
-+#
-+sub check_arch {
-+ $_ = `uname -m`;
-+ chomp;
-+ unless (m/armv4tl/) {
-+ warn "# \n# Can't execute on $_. Run on integrator platform.\n# \n";
-+ return 0;
-+ }
-+ return 1;
-+}
-+
-+#
-+#
-+sub load_module {
-+ my $params = shift;
-+ print "\nRemoving Module\n";
-+ system "rmmod dwc_otg";
-+ print "Loading Module\n";
-+ if ($params ne "") {
-+ print "Module Parameters: $params\n";
-+ }
-+ if (system("modprobe dwc_otg $params")) {
-+ warn "Unable to load module\n";
-+ return 0;
-+ }
-+ return 1;
-+}
-+
-+#
-+#
-+sub test_status {
-+ my $arg = shift;
-+
-+ print "\n";
-+
-+ if (defined $arg) {
-+ warn "WARNING: $arg\n";
-+ }
-+
-+ if ($errors > 0) {
-+ warn "TEST FAILED with $errors errors\n";
-+ return 0;
-+ } else {
-+ print "TEST PASSED\n";
-+ return 0 if (defined $arg);
-+ }
-+ return 1;
-+}
-+
-+#
-+#
-+ at EXPORT = qw(
-+$sysfsdir
-+$paramdir
-+$params
-+$errors
-+check_arch
-+load_module
-+test_status
-+);
-+
-+1;
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/test/test_mod_param.pl
-@@ -0,0 +1,133 @@
-+#!/usr/bin/perl -w
-+#
-+# Run this program on the integrator.
-+#
-+# - Tests module parameter default values.
-+# - Tests setting of valid module parameter values via modprobe.
-+# - Tests invalid module parameter values.
-+# -----------------------------------------------------------------------------
-+use strict;
-+use dwc_otg_test;
-+
-+check_arch() or die;
-+
-+#
-+#
-+sub test {
-+ my ($param,$expected) = @_;
-+ my $value = get($param);
-+
-+ if ($value == $expected) {
-+ print "$param = $value, okay\n";
-+ }
-+
-+ else {
-+ warn "ERROR: value of $param != $expected, $value\n";
-+ $errors ++;
-+ }
-+}
-+
-+#
-+#
-+sub get {
-+ my $param = shift;
-+ my $tmp = `cat $paramdir/$param`;
-+ chomp $tmp;
-+ return $tmp;
-+}
-+
-+#
-+#
-+sub test_main {
-+
-+ print "\nTesting Module Parameters\n";
-+
-+ load_module("") or die;
-+
-+ # Test initial values
-+ print "\nTesting Default Values\n";
-+ foreach (@{$params}) {
-+ test ($_->{NAME}, $_->{DEFAULT});
-+ }
-+
-+ # Test low value
-+ print "\nTesting Low Value\n";
-+ my $cmd_params = "";
-+ foreach (@{$params}) {
-+ $cmd_params = $cmd_params . "$_->{NAME}=$_->{LOW} ";
-+ }
-+ load_module($cmd_params) or die;
-+
-+ foreach (@{$params}) {
-+ test ($_->{NAME}, $_->{LOW});
-+ }
-+
-+ # Test high value
-+ print "\nTesting High Value\n";
-+ $cmd_params = "";
-+ foreach (@{$params}) {
-+ $cmd_params = $cmd_params . "$_->{NAME}=$_->{HIGH} ";
-+ }
-+ load_module($cmd_params) or die;
-+
-+ foreach (@{$params}) {
-+ test ($_->{NAME}, $_->{HIGH});
-+ }
-+
-+ # Test Enum
-+ print "\nTesting Enumerated\n";
-+ foreach (@{$params}) {
-+ if (defined $_->{ENUM}) {
-+ my $value;
-+ foreach $value (@{$_->{ENUM}}) {
-+ $cmd_params = "$_->{NAME}=$value";
-+ load_module($cmd_params) or die;
-+ test ($_->{NAME}, $value);
-+ }
-+ }
-+ }
-+
-+ # Test Invalid Values
-+ print "\nTesting Invalid Values\n";
-+ $cmd_params = "";
-+ foreach (@{$params}) {
-+ $cmd_params = $cmd_params . sprintf "$_->{NAME}=%d ", $_->{LOW}-1;
-+ }
-+ load_module($cmd_params) or die;
-+
-+ foreach (@{$params}) {
-+ test ($_->{NAME}, $_->{DEFAULT});
-+ }
-+
-+ $cmd_params = "";
-+ foreach (@{$params}) {
-+ $cmd_params = $cmd_params . sprintf "$_->{NAME}=%d ", $_->{HIGH}+1;
-+ }
-+ load_module($cmd_params) or die;
-+
-+ foreach (@{$params}) {
-+ test ($_->{NAME}, $_->{DEFAULT});
-+ }
-+
-+ print "\nTesting Enumerated\n";
-+ foreach (@{$params}) {
-+ if (defined $_->{ENUM}) {
-+ my $value;
-+ foreach $value (@{$_->{ENUM}}) {
-+ $value = $value + 1;
-+ $cmd_params = "$_->{NAME}=$value";
-+ load_module($cmd_params) or die;
-+ test ($_->{NAME}, $_->{DEFAULT});
-+ $value = $value - 2;
-+ $cmd_params = "$_->{NAME}=$value";
-+ load_module($cmd_params) or die;
-+ test ($_->{NAME}, $_->{DEFAULT});
-+ }
-+ }
-+ }
-+
-+ test_status() or die;
-+}
-+
-+test_main();
-+0;
---- /dev/null
-+++ b/drivers/usb/host/dwc_otg/test/test_sysfs.pl
-@@ -0,0 +1,193 @@
-+#!/usr/bin/perl -w
-+#
-+# Run this program on the integrator
-+# - Tests select sysfs attributes.
-+# - Todo ... test more attributes, hnp/srp, buspower/bussuspend, etc.
-+# -----------------------------------------------------------------------------
-+use strict;
-+use dwc_otg_test;
-+
-+check_arch() or die;
-+
-+#
-+#
-+sub test {
-+ my ($attr,$expected) = @_;
-+ my $string = get($attr);
-+
-+ if ($string eq $expected) {
-+ printf("$attr = $string, okay\n");
-+ }
-+ else {
-+ warn "ERROR: value of $attr != $expected, $string\n";
-+ $errors ++;
-+ }
-+}
-+
-+#
-+#
-+sub set {
-+ my ($reg, $value) = @_;
-+ system "echo $value > $sysfsdir/$reg";
-+}
-+
-+#
-+#
-+sub get {
-+ my $attr = shift;
-+ my $string = `cat $sysfsdir/$attr`;
-+ chomp $string;
-+ if ($string =~ m/\s\=\s/) {
-+ my $tmp;
-+ ($tmp, $string) = split /\s=\s/, $string;
-+ }
-+ return $string;
-+}
-+
-+#
-+#
-+sub test_main {
-+ print("\nTesting Sysfs Attributes\n");
-+
-+ load_module("") or die;
-+
-+ # Test initial values of regoffset/regvalue/guid/gsnpsid
-+ print("\nTesting Default Values\n");
-+
-+ test("regoffset", "0xffffffff");
-+ test("regvalue", "invalid offset");
-+ test("guid", "0x12345678"); # this will fail if it has been changed
-+ test("gsnpsid", "0x4f54200a");
-+
-+ # Test operation of regoffset/regvalue
-+ print("\nTesting regoffset\n");
-+ set('regoffset', '5a5a5a5a');
-+ test("regoffset", "0xffffffff");
-+
-+ set('regoffset', '0');
-+ test("regoffset", "0x00000000");
-+
-+ set('regoffset', '40000');
-+ test("regoffset", "0x00000000");
-+
-+ set('regoffset', '3ffff');
-+ test("regoffset", "0x0003ffff");
-+
-+ set('regoffset', '1');
-+ test("regoffset", "0x00000001");
-+
-+ print("\nTesting regvalue\n");
-+ set('regoffset', '3c');
-+ test("regvalue", "0x12345678");
-+ set('regvalue', '5a5a5a5a');
-+ test("regvalue", "0x5a5a5a5a");
-+ set('regvalue','a5a5a5a5');
-+ test("regvalue", "0xa5a5a5a5");
-+ set('guid','12345678');
-+
-+ # Test HNP Capable
-+ print("\nTesting HNP Capable bit\n");
-+ set('hnpcapable', '1');
-+ test("hnpcapable", "0x1");
-+ set('hnpcapable','0');
-+ test("hnpcapable", "0x0");
-+
-+ set('regoffset','0c');
-+
-+ my $old = get('gusbcfg');
-+ print("setting hnpcapable\n");
-+ set('hnpcapable', '1');
-+ test("hnpcapable", "0x1");
-+ test('gusbcfg', sprintf "0x%08x", (oct ($old) | (1<<9)));
-+ test('regvalue', sprintf "0x%08x", (oct ($old) | (1<<9)));
-+
-+ $old = get('gusbcfg');
-+ print("clearing hnpcapable\n");
-+ set('hnpcapable', '0');
-+ test("hnpcapable", "0x0");
-+ test ('gusbcfg', sprintf "0x%08x", oct ($old) & (~(1<<9)));
-+ test ('regvalue', sprintf "0x%08x", oct ($old) & (~(1<<9)));
-+
-+ # Test SRP Capable
-+ print("\nTesting SRP Capable bit\n");
-+ set('srpcapable', '1');
-+ test("srpcapable", "0x1");
-+ set('srpcapable','0');
-+ test("srpcapable", "0x0");
-+
-+ set('regoffset','0c');
-+
-+ $old = get('gusbcfg');
-+ print("setting srpcapable\n");
-+ set('srpcapable', '1');
-+ test("srpcapable", "0x1");
-+ test('gusbcfg', sprintf "0x%08x", (oct ($old) | (1<<8)));
-+ test('regvalue', sprintf "0x%08x", (oct ($old) | (1<<8)));
-+
-+ $old = get('gusbcfg');
-+ print("clearing srpcapable\n");
-+ set('srpcapable', '0');
-+ test("srpcapable", "0x0");
-+ test('gusbcfg', sprintf "0x%08x", oct ($old) & (~(1<<8)));
-+ test('regvalue', sprintf "0x%08x", oct ($old) & (~(1<<8)));
-+
-+ # Test GGPIO
-+ print("\nTesting GGPIO\n");
-+ set('ggpio','5a5a5a5a');
-+ test('ggpio','0x5a5a0000');
-+ set('ggpio','a5a5a5a5');
-+ test('ggpio','0xa5a50000');
-+ set('ggpio','11110000');
-+ test('ggpio','0x11110000');
-+ set('ggpio','00001111');
-+ test('ggpio','0x00000000');
-+
-+ # Test DEVSPEED
-+ print("\nTesting DEVSPEED\n");
-+ set('regoffset','800');
-+ $old = get('regvalue');
-+ set('devspeed','0');
-+ test('devspeed','0x0');
-+ test('regvalue',sprintf("0x%08x", oct($old) & ~(0x3)));
-+ set('devspeed','1');
-+ test('devspeed','0x1');
-+ test('regvalue',sprintf("0x%08x", oct($old) & ~(0x3) | 1));
-+ set('devspeed','2');
-+ test('devspeed','0x2');
-+ test('regvalue',sprintf("0x%08x", oct($old) & ~(0x3) | 2));
-+ set('devspeed','3');
-+ test('devspeed','0x3');
-+ test('regvalue',sprintf("0x%08x", oct($old) & ~(0x3) | 3));
-+ set('devspeed','4');
-+ test('devspeed','0x0');
-+ test('regvalue',sprintf("0x%08x", oct($old) & ~(0x3)));
-+ set('devspeed','5');
-+ test('devspeed','0x1');
-+ test('regvalue',sprintf("0x%08x", oct($old) & ~(0x3) | 1));
-+
-+
-+ # mode Returns the current mode:0 for device mode1 for host mode Read
-+ # hnp Initiate the Host Negotiation Protocol. Read returns the status. Read/Write
-+ # srp Initiate the Session Request Protocol. Read returns the status. Read/Write
-+ # buspower Get or Set the Power State of the bus (0 - Off or 1 - On) Read/Write
-+ # bussuspend Suspend the USB bus. Read/Write
-+ # busconnected Get the connection status of the bus Read
-+
-+ # gotgctl Get or set the Core Control Status Register. Read/Write
-+ ## gusbcfg Get or set the Core USB Configuration Register Read/Write
-+ # grxfsiz Get or set the Receive FIFO Size Register Read/Write
-+ # gnptxfsiz Get or set the non-periodic Transmit Size Register Read/Write
-+ # gpvndctl Get or set the PHY Vendor Control Register Read/Write
-+ ## ggpio Get the value in the lower 16-bits of the General Purpose IO Register or Set the upper 16 bits. Read/Write
-+ ## guid Get or set the value of the User ID Register Read/Write
-+ ## gsnpsid Get the value of the Synopsys ID Regester Read
-+ ## devspeed Get or set the device speed setting in the DCFG register Read/Write
-+ # enumspeed Gets the device enumeration Speed. Read
-+ # hptxfsiz Get the value of the Host Periodic Transmit FIFO Read
-+ # hprt0 Get or Set the value in the Host Port Control and Status Register Read/Write
-+
-+ test_status("TEST NYI") or die;
-+}
-+
-+test_main();
-+0;
diff --git a/target/linux/brcm2708/patches-4.4/0030-bcm2708-framebuffer-driver.patch b/target/linux/brcm2708/patches-4.4/0030-bcm2708-framebuffer-driver.patch
deleted file mode 100644
index 694fb86..0000000
--- a/target/linux/brcm2708/patches-4.4/0030-bcm2708-framebuffer-driver.patch
+++ /dev/null
@@ -1,3455 +0,0 @@
-From cdee11ba41b516613aa20c0c661d5e2f4c911103 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Wed, 17 Jun 2015 17:06:34 +0100
-Subject: [PATCH] bcm2708 framebuffer driver
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Signed-off-by: popcornmix <popcornmix at gmail.com>
-
-bcm2708_fb : Implement blanking support using the mailbox property interface
-
-bcm2708_fb: Add pan and vsync controls
-
-bcm2708_fb: DMA acceleration for fb_copyarea
-
-Based on http://www.raspberrypi.org/phpBB3/viewtopic.php?p=62425#p62425
-Also used Simon's dmaer_master module as a reference for tweaking DMA
-settings for better performance.
-
-For now busylooping only. IRQ support might be added later.
-With non-overclocked Raspberry Pi, the performance is ~360 MB/s
-for simple copy or ~260 MB/s for two-pass copy (used when dragging
-windows to the right).
-
-In the case of using DMA channel 0, the performance improves
-to ~440 MB/s.
-
-For comparison, VFP optimized CPU copy can only do ~114 MB/s in
-the same conditions (hindered by reading uncached source buffer).
-
-Signed-off-by: Siarhei Siamashka <siarhei.siamashka at gmail.com>
-
-bcm2708_fb: report number of dma copies
-
-Add a counter (exported via debugfs) reporting the
-number of dma copies that the framebuffer driver
-has done, in order to help evaluate different
-optimization strategies.
-
-Signed-off-by: Luke Diamand <luked at broadcom.com>
-
-bcm2708_fb: use IRQ for DMA copies
-
-The copyarea ioctl() uses DMA to speed things along. This
-was busy-waiting for completion. This change supports using
-an interrupt instead for larger transfers. For small
-transfers, busy-waiting is still likely to be faster.
-
-Signed-off-by: Luke Diamand <luke at diamand.org>
-
-bcm2708: Make ioctl logging quieter
-
-video: fbdev: bcm2708_fb: Don't panic on error
-
-No need to panic the kernel if the video driver fails.
-Just print a message and return an error.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-fbdev: bcm2708_fb: Add ARCH_BCM2835 support
-
-Add Device Tree support.
-Pass the device to dma_alloc_coherent() in order to get the
-correct bus address on ARCH_BCM2835.
-Use the new DMA legacy API header file.
-Including <mach/platform.h> is not necessary.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-BCM270x_DT: Add bcm2708-fb device
-
-Add bcm2708-fb to Device Tree and don't add the
-platform device when booting in DT mode.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
----
- drivers/video/fbdev/Kconfig | 14 +
- drivers/video/fbdev/Makefile | 1 +
- drivers/video/fbdev/bcm2708_fb.c | 847 ++++++++++
- drivers/video/logo/logo_linux_clut224.ppm | 2483 ++++++++++-------------------
- 4 files changed, 1743 insertions(+), 1602 deletions(-)
- create mode 100644 drivers/video/fbdev/bcm2708_fb.c
-
---- a/drivers/video/fbdev/Kconfig
-+++ b/drivers/video/fbdev/Kconfig
-@@ -224,6 +224,20 @@ config FB_TILEBLITTING
- comment "Frame buffer hardware drivers"
- depends on FB
-
-+config FB_BCM2708
-+ tristate "BCM2708 framebuffer support"
-+ depends on FB && RASPBERRYPI_FIRMWARE
-+ select FB_CFB_FILLRECT
-+ select FB_CFB_COPYAREA
-+ select FB_CFB_IMAGEBLIT
-+ help
-+ This framebuffer device driver is for the BCM2708 framebuffer.
-+
-+ If you want to compile this as a module (=code which can be
-+ inserted into and removed from the running kernel), say M
-+ here and read <file:Documentation/kbuild/modules.txt>. The module
-+ will be called bcm2708_fb.
-+
- config FB_GRVGA
- tristate "Aeroflex Gaisler framebuffer support"
- depends on FB && SPARC
---- a/drivers/video/fbdev/Makefile
-+++ b/drivers/video/fbdev/Makefile
-@@ -12,6 +12,7 @@ obj-$(CONFIG_FB_MACMODES) += macmod
- obj-$(CONFIG_FB_WMT_GE_ROPS) += wmt_ge_rops.o
-
- # Hardware specific drivers go first
-+obj-$(CONFIG_FB_BCM2708) += bcm2708_fb.o
- obj-$(CONFIG_FB_AMIGA) += amifb.o c2p_planar.o
- obj-$(CONFIG_FB_ARC) += arcfb.o
- obj-$(CONFIG_FB_CLPS711X) += clps711x-fb.o
---- /dev/null
-+++ b/drivers/video/fbdev/bcm2708_fb.c
-@@ -0,0 +1,847 @@
-+/*
-+ * linux/drivers/video/bcm2708_fb.c
-+ *
-+ * Copyright (C) 2010 Broadcom
-+ *
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License. See the file COPYING in the main directory of this archive
-+ * for more details.
-+ *
-+ * Broadcom simple framebuffer driver
-+ *
-+ * This file is derived from cirrusfb.c
-+ * Copyright 1999-2001 Jeff Garzik <jgarzik at pobox.com>
-+ *
-+ */
-+#include <linux/module.h>
-+#include <linux/kernel.h>
-+#include <linux/errno.h>
-+#include <linux/string.h>
-+#include <linux/slab.h>
-+#include <linux/mm.h>
-+#include <linux/fb.h>
-+#include <linux/init.h>
-+#include <linux/interrupt.h>
-+#include <linux/ioport.h>
-+#include <linux/list.h>
-+#include <linux/platform_data/dma-bcm2708.h>
-+#include <linux/platform_device.h>
-+#include <linux/clk.h>
-+#include <linux/printk.h>
-+#include <linux/console.h>
-+#include <linux/debugfs.h>
-+#include <asm/sizes.h>
-+#include <linux/io.h>
-+#include <linux/dma-mapping.h>
-+#include <soc/bcm2835/raspberrypi-firmware.h>
-+
-+//#define BCM2708_FB_DEBUG
-+#define MODULE_NAME "bcm2708_fb"
-+
-+#ifdef BCM2708_FB_DEBUG
-+#define print_debug(fmt,...) pr_debug("%s:%s:%d: "fmt, MODULE_NAME, __func__, __LINE__, ##__VA_ARGS__)
-+#else
-+#define print_debug(fmt,...)
-+#endif
-+
-+/* This is limited to 16 characters when displayed by X startup */
-+static const char *bcm2708_name = "BCM2708 FB";
-+
-+#define DRIVER_NAME "bcm2708_fb"
-+
-+static int fbwidth = 800; /* module parameter */
-+static int fbheight = 480; /* module parameter */
-+static int fbdepth = 16; /* module parameter */
-+static int fbswap = 0; /* module parameter */
-+
-+static u32 dma_busy_wait_threshold = 1<<15;
-+module_param(dma_busy_wait_threshold, int, 0644);
-+MODULE_PARM_DESC(dma_busy_wait_threshold, "Busy-wait for DMA completion below this area");
-+
-+struct fb_alloc_tags {
-+ struct rpi_firmware_property_tag_header tag1;
-+ u32 xres, yres;
-+ struct rpi_firmware_property_tag_header tag2;
-+ u32 xres_virtual, yres_virtual;
-+ struct rpi_firmware_property_tag_header tag3;
-+ u32 bpp;
-+ struct rpi_firmware_property_tag_header tag4;
-+ u32 xoffset, yoffset;
-+ struct rpi_firmware_property_tag_header tag5;
-+ u32 base, screen_size;
-+ struct rpi_firmware_property_tag_header tag6;
-+ u32 pitch;
-+};
-+
-+struct bcm2708_fb_stats {
-+ struct debugfs_regset32 regset;
-+ u32 dma_copies;
-+ u32 dma_irqs;
-+};
-+
-+struct bcm2708_fb {
-+ struct fb_info fb;
-+ struct platform_device *dev;
-+ struct rpi_firmware *fw;
-+ u32 cmap[16];
-+ u32 gpu_cmap[256];
-+ int dma_chan;
-+ int dma_irq;
-+ void __iomem *dma_chan_base;
-+ void *cb_base; /* DMA control blocks */
-+ dma_addr_t cb_handle;
-+ struct dentry *debugfs_dir;
-+ wait_queue_head_t dma_waitq;
-+ struct bcm2708_fb_stats stats;
-+ unsigned long fb_bus_address;
-+};
-+
-+#define to_bcm2708(info) container_of(info, struct bcm2708_fb, fb)
-+
-+static void bcm2708_fb_debugfs_deinit(struct bcm2708_fb *fb)
-+{
-+ debugfs_remove_recursive(fb->debugfs_dir);
-+ fb->debugfs_dir = NULL;
-+}
-+
-+static int bcm2708_fb_debugfs_init(struct bcm2708_fb *fb)
-+{
-+ static struct debugfs_reg32 stats_registers[] = {
-+ {
-+ "dma_copies",
-+ offsetof(struct bcm2708_fb_stats, dma_copies)
-+ },
-+ {
-+ "dma_irqs",
-+ offsetof(struct bcm2708_fb_stats, dma_irqs)
-+ },
-+ };
-+
-+ fb->debugfs_dir = debugfs_create_dir(DRIVER_NAME, NULL);
-+ if (!fb->debugfs_dir) {
-+ pr_warn("%s: could not create debugfs entry\n",
-+ __func__);
-+ return -EFAULT;
-+ }
-+
-+ fb->stats.regset.regs = stats_registers;
-+ fb->stats.regset.nregs = ARRAY_SIZE(stats_registers);
-+ fb->stats.regset.base = &fb->stats;
-+
-+ if (!debugfs_create_regset32(
-+ "stats", 0444, fb->debugfs_dir, &fb->stats.regset)) {
-+ pr_warn("%s: could not create statistics registers\n",
-+ __func__);
-+ goto fail;
-+ }
-+ return 0;
-+
-+fail:
-+ bcm2708_fb_debugfs_deinit(fb);
-+ return -EFAULT;
-+}
-+
-+static int bcm2708_fb_set_bitfields(struct fb_var_screeninfo *var)
-+{
-+ int ret = 0;
-+
-+ memset(&var->transp, 0, sizeof(var->transp));
-+
-+ var->red.msb_right = 0;
-+ var->green.msb_right = 0;
-+ var->blue.msb_right = 0;
-+
-+ switch (var->bits_per_pixel) {
-+ case 1:
-+ case 2:
-+ case 4:
-+ case 8:
-+ var->red.length = var->bits_per_pixel;
-+ var->red.offset = 0;
-+ var->green.length = var->bits_per_pixel;
-+ var->green.offset = 0;
-+ var->blue.length = var->bits_per_pixel;
-+ var->blue.offset = 0;
-+ break;
-+ case 16:
-+ var->red.length = 5;
-+ var->blue.length = 5;
-+ /*
-+ * Green length can be 5 or 6 depending whether
-+ * we're operating in RGB555 or RGB565 mode.
-+ */
-+ if (var->green.length != 5 && var->green.length != 6)
-+ var->green.length = 6;
-+ break;
-+ case 24:
-+ var->red.length = 8;
-+ var->blue.length = 8;
-+ var->green.length = 8;
-+ break;
-+ case 32:
-+ var->red.length = 8;
-+ var->green.length = 8;
-+ var->blue.length = 8;
-+ var->transp.length = 8;
-+ break;
-+ default:
-+ ret = -EINVAL;
-+ break;
-+ }
-+
-+ /*
-+ * >= 16bpp displays have separate colour component bitfields
-+ * encoded in the pixel data. Calculate their position from
-+ * the bitfield length defined above.
-+ */
-+ if (ret == 0 && var->bits_per_pixel >= 24 && fbswap) {
-+ var->blue.offset = 0;
-+ var->green.offset = var->blue.offset + var->blue.length;
-+ var->red.offset = var->green.offset + var->green.length;
-+ var->transp.offset = var->red.offset + var->red.length;
-+ } else if (ret == 0 && var->bits_per_pixel >= 24) {
-+ var->red.offset = 0;
-+ var->green.offset = var->red.offset + var->red.length;
-+ var->blue.offset = var->green.offset + var->green.length;
-+ var->transp.offset = var->blue.offset + var->blue.length;
-+ } else if (ret == 0 && var->bits_per_pixel >= 16) {
-+ var->blue.offset = 0;
-+ var->green.offset = var->blue.offset + var->blue.length;
-+ var->red.offset = var->green.offset + var->green.length;
-+ var->transp.offset = var->red.offset + var->red.length;
-+ }
-+
-+ return ret;
-+}
-+
-+static int bcm2708_fb_check_var(struct fb_var_screeninfo *var,
-+ struct fb_info *info)
-+{
-+ /* info input, var output */
-+ int yres;
-+
-+ /* info input, var output */
-+ print_debug("bcm2708_fb_check_var info(%p) %dx%d (%dx%d), %d, %d\n", info,
-+ info->var.xres, info->var.yres, info->var.xres_virtual,
-+ info->var.yres_virtual, (int)info->screen_size,
-+ info->var.bits_per_pixel);
-+ print_debug("bcm2708_fb_check_var var(%p) %dx%d (%dx%d), %d\n", var,
-+ var->xres, var->yres, var->xres_virtual, var->yres_virtual,
-+ var->bits_per_pixel);
-+
-+ if (!var->bits_per_pixel)
-+ var->bits_per_pixel = 16;
-+
-+ if (bcm2708_fb_set_bitfields(var) != 0) {
-+ pr_err("bcm2708_fb_check_var: invalid bits_per_pixel %d\n",
-+ var->bits_per_pixel);
-+ return -EINVAL;
-+ }
-+
-+
-+ if (var->xres_virtual < var->xres)
-+ var->xres_virtual = var->xres;
-+ /* use highest possible virtual resolution */
-+ if (var->yres_virtual == -1) {
-+ var->yres_virtual = 480;
-+
-+ pr_err
-+ ("bcm2708_fb_check_var: virtual resolution set to maximum of %dx%d\n",
-+ var->xres_virtual, var->yres_virtual);
-+ }
-+ if (var->yres_virtual < var->yres)
-+ var->yres_virtual = var->yres;
-+
-+ if (var->xoffset < 0)
-+ var->xoffset = 0;
-+ if (var->yoffset < 0)
-+ var->yoffset = 0;
-+
-+ /* truncate xoffset and yoffset to maximum if too high */
-+ if (var->xoffset > var->xres_virtual - var->xres)
-+ var->xoffset = var->xres_virtual - var->xres - 1;
-+ if (var->yoffset > var->yres_virtual - var->yres)
-+ var->yoffset = var->yres_virtual - var->yres - 1;
-+
-+ return 0;
-+}
-+
-+static int bcm2708_fb_set_par(struct fb_info *info)
-+{
-+ struct bcm2708_fb *fb = to_bcm2708(info);
-+ struct fb_alloc_tags fbinfo = {
-+ .tag1 = { RPI_FIRMWARE_FRAMEBUFFER_SET_PHYSICAL_WIDTH_HEIGHT,
-+ 8, 0, },
-+ .xres = info->var.xres,
-+ .yres = info->var.yres,
-+ .tag2 = { RPI_FIRMWARE_FRAMEBUFFER_SET_VIRTUAL_WIDTH_HEIGHT,
-+ 8, 0, },
-+ .xres_virtual = info->var.xres_virtual,
-+ .yres_virtual = info->var.yres_virtual,
-+ .tag3 = { RPI_FIRMWARE_FRAMEBUFFER_SET_DEPTH, 4, 0 },
-+ .bpp = info->var.bits_per_pixel,
-+ .tag4 = { RPI_FIRMWARE_FRAMEBUFFER_SET_VIRTUAL_OFFSET, 8, 0 },
-+ .xoffset = info->var.xoffset,
-+ .yoffset = info->var.yoffset,
-+ .tag5 = { RPI_FIRMWARE_FRAMEBUFFER_ALLOCATE, 8, 0 },
-+ .base = 0,
-+ .screen_size = 0,
-+ .tag6 = { RPI_FIRMWARE_FRAMEBUFFER_GET_PITCH, 4, 0 },
-+ .pitch = 0,
-+ };
-+ int ret;
-+
-+ print_debug("bcm2708_fb_set_par info(%p) %dx%d (%dx%d), %d, %d\n", info,
-+ info->var.xres, info->var.yres, info->var.xres_virtual,
-+ info->var.yres_virtual, (int)info->screen_size,
-+ info->var.bits_per_pixel);
-+
-+ ret = rpi_firmware_property_list(fb->fw, &fbinfo, sizeof(fbinfo));
-+ if (ret) {
-+ dev_err(info->device,
-+ "Failed to allocate GPU framebuffer (%d)\n", ret);
-+ return ret;
-+ }
-+
-+ if (info->var.bits_per_pixel <= 8)
-+ fb->fb.fix.visual = FB_VISUAL_PSEUDOCOLOR;
-+ else
-+ fb->fb.fix.visual = FB_VISUAL_TRUECOLOR;
-+
-+ fb->fb.fix.line_length = fbinfo.pitch;
-+ fbinfo.base |= 0x40000000;
-+ fb->fb_bus_address = fbinfo.base;
-+ fbinfo.base &= ~0xc0000000;
-+ fb->fb.fix.smem_start = fbinfo.base;
-+ fb->fb.fix.smem_len = fbinfo.pitch * fbinfo.yres_virtual;
-+ fb->fb.screen_size = fbinfo.screen_size;
-+ if (fb->fb.screen_base)
-+ iounmap(fb->fb.screen_base);
-+ fb->fb.screen_base = ioremap_wc(fbinfo.base, fb->fb.screen_size);
-+ if (!fb->fb.screen_base) {
-+ /* the console may currently be locked */
-+ console_trylock();
-+ console_unlock();
-+ dev_err(info->device, "Failed to set screen_base\n");
-+ return -ENOMEM;
-+ }
-+
-+ print_debug
-+ ("BCM2708FB: start = %p,%p width=%d, height=%d, bpp=%d, pitch=%d size=%d\n",
-+ (void *)fb->fb.screen_base, (void *)fb->fb_bus_address,
-+ fbinfo.xres, fbinfo.yres, fbinfo.bpp,
-+ fbinfo.pitch, (int)fb->fb.screen_size);
-+
-+ return 0;
-+}
-+
-+static inline u32 convert_bitfield(int val, struct fb_bitfield *bf)
-+{
-+ unsigned int mask = (1 << bf->length) - 1;
-+
-+ return (val >> (16 - bf->length) & mask) << bf->offset;
-+}
-+
-+
-+static int bcm2708_fb_setcolreg(unsigned int regno, unsigned int red,
-+ unsigned int green, unsigned int blue,
-+ unsigned int transp, struct fb_info *info)
-+{
-+ struct bcm2708_fb *fb = to_bcm2708(info);
-+
-+ /*print_debug("BCM2708FB: setcolreg %d:(%02x,%02x,%02x,%02x) %x\n", regno, red, green, blue, transp, fb->fb.fix.visual);*/
-+ if (fb->fb.var.bits_per_pixel <= 8) {
-+ if (regno < 256) {
-+ /* blue [23:16], green [15:8], red [7:0] */
-+ fb->gpu_cmap[regno] = ((red >> 8) & 0xff) << 0 |
-+ ((green >> 8) & 0xff) << 8 |
-+ ((blue >> 8) & 0xff) << 16;
-+ }
-+ /* Hack: we need to tell GPU the palette has changed, but currently bcm2708_fb_set_par takes noticable time when called for every (256) colour */
-+ /* So just call it for what looks like the last colour in a list for now. */
-+ if (regno == 15 || regno == 255) {
-+ struct packet {
-+ u32 offset;
-+ u32 length;
-+ u32 cmap[256];
-+ } *packet;
-+ int ret;
-+
-+ packet = kmalloc(sizeof(*packet), GFP_KERNEL);
-+ if (!packet)
-+ return -ENOMEM;
-+ packet->offset = 0;
-+ packet->length = regno + 1;
-+ memcpy(packet->cmap, fb->gpu_cmap, sizeof(packet->cmap));
-+ ret = rpi_firmware_property(fb->fw, RPI_FIRMWARE_FRAMEBUFFER_SET_PALETTE,
-+ packet, (2 + packet->length) * sizeof(u32));
-+ if (ret || packet->offset)
-+ dev_err(info->device, "Failed to set palette (%d,%u)\n",
-+ ret, packet->offset);
-+ kfree(packet);
-+ }
-+ } else if (regno < 16) {
-+ fb->cmap[regno] = convert_bitfield(transp, &fb->fb.var.transp) |
-+ convert_bitfield(blue, &fb->fb.var.blue) |
-+ convert_bitfield(green, &fb->fb.var.green) |
-+ convert_bitfield(red, &fb->fb.var.red);
-+ }
-+ return regno > 255;
-+}
-+
-+static int bcm2708_fb_blank(int blank_mode, struct fb_info *info)
-+{
-+ struct bcm2708_fb *fb = to_bcm2708(info);
-+ u32 value;
-+ int ret;
-+
-+ switch (blank_mode) {
-+ case FB_BLANK_UNBLANK:
-+ value = 0;
-+ break;
-+ case FB_BLANK_NORMAL:
-+ case FB_BLANK_VSYNC_SUSPEND:
-+ case FB_BLANK_HSYNC_SUSPEND:
-+ case FB_BLANK_POWERDOWN:
-+ value = 1;
-+ break;
-+ default:
-+ return -EINVAL;
-+ }
-+
-+ ret = rpi_firmware_property(fb->fw, RPI_FIRMWARE_FRAMEBUFFER_BLANK,
-+ &value, sizeof(value));
-+ if (ret)
-+ dev_err(info->device, "bcm2708_fb_blank(%d) failed: %d\n",
-+ blank_mode, ret);
-+
-+ return ret;
-+}
-+
-+static int bcm2708_fb_pan_display(struct fb_var_screeninfo *var, struct fb_info *info)
-+{
-+ s32 result;
-+ info->var.xoffset = var->xoffset;
-+ info->var.yoffset = var->yoffset;
-+ result = bcm2708_fb_set_par(info);
-+ if (result != 0)
-+ pr_err("bcm2708_fb_pan_display(%d,%d) returns=%d\n", var->xoffset, var->yoffset, result);
-+ return result;
-+}
-+
-+static int bcm2708_ioctl(struct fb_info *info, unsigned int cmd, unsigned long arg)
-+{
-+ struct bcm2708_fb *fb = to_bcm2708(info);
-+ u32 dummy = 0;
-+ int ret;
-+
-+ switch (cmd) {
-+ case FBIO_WAITFORVSYNC:
-+ ret = rpi_firmware_property(fb->fw,
-+ RPI_FIRMWARE_FRAMEBUFFER_SET_VSYNC,
-+ &dummy, sizeof(dummy));
-+ break;
-+ default:
-+ dev_dbg(info->device, "Unknown ioctl 0x%x\n", cmd);
-+ return -ENOTTY;
-+ }
-+
-+ if (ret)
-+ dev_err(info->device, "ioctl 0x%x failed (%d)\n", cmd, ret);
-+
-+ return ret;
-+}
-+static void bcm2708_fb_fillrect(struct fb_info *info,
-+ const struct fb_fillrect *rect)
-+{
-+ /* (is called) print_debug("bcm2708_fb_fillrect\n"); */
-+ cfb_fillrect(info, rect);
-+}
-+
-+/* A helper function for configuring dma control block */
-+static void set_dma_cb(struct bcm2708_dma_cb *cb,
-+ int burst_size,
-+ dma_addr_t dst,
-+ int dst_stride,
-+ dma_addr_t src,
-+ int src_stride,
-+ int w,
-+ int h)
-+{
-+ cb->info = BCM2708_DMA_BURST(burst_size) | BCM2708_DMA_S_WIDTH |
-+ BCM2708_DMA_S_INC | BCM2708_DMA_D_WIDTH |
-+ BCM2708_DMA_D_INC | BCM2708_DMA_TDMODE;
-+ cb->dst = dst;
-+ cb->src = src;
-+ /*
-+ * This is not really obvious from the DMA documentation,
-+ * but the top 16 bits must be programmmed to "height -1"
-+ * and not "height" in 2D mode.
-+ */
-+ cb->length = ((h - 1) << 16) | w;
-+ cb->stride = ((dst_stride - w) << 16) | (u16)(src_stride - w);
-+ cb->pad[0] = 0;
-+ cb->pad[1] = 0;
-+}
-+
-+static void bcm2708_fb_copyarea(struct fb_info *info,
-+ const struct fb_copyarea *region)
-+{
-+ struct bcm2708_fb *fb = to_bcm2708(info);
-+ struct bcm2708_dma_cb *cb = fb->cb_base;
-+ int bytes_per_pixel = (info->var.bits_per_pixel + 7) >> 3;
-+ /* Channel 0 supports larger bursts and is a bit faster */
-+ int burst_size = (fb->dma_chan == 0) ? 8 : 2;
-+ int pixels = region->width * region->height;
-+
-+ /* Fallback to cfb_copyarea() if we don't like something */
-+ if (in_atomic() ||
-+ bytes_per_pixel > 4 ||
-+ info->var.xres * info->var.yres > 1920 * 1200 ||
-+ region->width <= 0 || region->width > info->var.xres ||
-+ region->height <= 0 || region->height > info->var.yres ||
-+ region->sx < 0 || region->sx >= info->var.xres ||
-+ region->sy < 0 || region->sy >= info->var.yres ||
-+ region->dx < 0 || region->dx >= info->var.xres ||
-+ region->dy < 0 || region->dy >= info->var.yres ||
-+ region->sx + region->width > info->var.xres ||
-+ region->dx + region->width > info->var.xres ||
-+ region->sy + region->height > info->var.yres ||
-+ region->dy + region->height > info->var.yres) {
-+ cfb_copyarea(info, region);
-+ return;
-+ }
-+
-+ if (region->dy == region->sy && region->dx > region->sx) {
-+ /*
-+ * A difficult case of overlapped copy. Because DMA can't
-+ * copy individual scanlines in backwards direction, we need
-+ * two-pass processing. We do it by programming a chain of dma
-+ * control blocks in the first 16K part of the buffer and use
-+ * the remaining 48K as the intermediate temporary scratch
-+ * buffer. The buffer size is sufficient to handle up to
-+ * 1920x1200 resolution at 32bpp pixel depth.
-+ */
-+ int y;
-+ dma_addr_t control_block_pa = fb->cb_handle;
-+ dma_addr_t scratchbuf = fb->cb_handle + 16 * 1024;
-+ int scanline_size = bytes_per_pixel * region->width;
-+ int scanlines_per_cb = (64 * 1024 - 16 * 1024) / scanline_size;
-+
-+ for (y = 0; y < region->height; y += scanlines_per_cb) {
-+ dma_addr_t src =
-+ fb->fb_bus_address +
-+ bytes_per_pixel * region->sx +
-+ (region->sy + y) * fb->fb.fix.line_length;
-+ dma_addr_t dst =
-+ fb->fb_bus_address +
-+ bytes_per_pixel * region->dx +
-+ (region->dy + y) * fb->fb.fix.line_length;
-+
-+ if (region->height - y < scanlines_per_cb)
-+ scanlines_per_cb = region->height - y;
-+
-+ set_dma_cb(cb, burst_size, scratchbuf, scanline_size,
-+ src, fb->fb.fix.line_length,
-+ scanline_size, scanlines_per_cb);
-+ control_block_pa += sizeof(struct bcm2708_dma_cb);
-+ cb->next = control_block_pa;
-+ cb++;
-+
-+ set_dma_cb(cb, burst_size, dst, fb->fb.fix.line_length,
-+ scratchbuf, scanline_size,
-+ scanline_size, scanlines_per_cb);
-+ control_block_pa += sizeof(struct bcm2708_dma_cb);
-+ cb->next = control_block_pa;
-+ cb++;
-+ }
-+ /* move the pointer back to the last dma control block */
-+ cb--;
-+ } else {
-+ /* A single dma control block is enough. */
-+ int sy, dy, stride;
-+ if (region->dy <= region->sy) {
-+ /* processing from top to bottom */
-+ dy = region->dy;
-+ sy = region->sy;
-+ stride = fb->fb.fix.line_length;
-+ } else {
-+ /* processing from bottom to top */
-+ dy = region->dy + region->height - 1;
-+ sy = region->sy + region->height - 1;
-+ stride = -fb->fb.fix.line_length;
-+ }
-+ set_dma_cb(cb, burst_size,
-+ fb->fb_bus_address + dy * fb->fb.fix.line_length +
-+ bytes_per_pixel * region->dx,
-+ stride,
-+ fb->fb_bus_address + sy * fb->fb.fix.line_length +
-+ bytes_per_pixel * region->sx,
-+ stride,
-+ region->width * bytes_per_pixel,
-+ region->height);
-+ }
-+
-+ /* end of dma control blocks chain */
-+ cb->next = 0;
-+
-+
-+ if (pixels < dma_busy_wait_threshold) {
-+ bcm_dma_start(fb->dma_chan_base, fb->cb_handle);
-+ bcm_dma_wait_idle(fb->dma_chan_base);
-+ } else {
-+ void __iomem *dma_chan = fb->dma_chan_base;
-+ cb->info |= BCM2708_DMA_INT_EN;
-+ bcm_dma_start(fb->dma_chan_base, fb->cb_handle);
-+ while (bcm_dma_is_busy(dma_chan)) {
-+ wait_event_interruptible(
-+ fb->dma_waitq,
-+ !bcm_dma_is_busy(dma_chan));
-+ }
-+ fb->stats.dma_irqs++;
-+ }
-+ fb->stats.dma_copies++;
-+}
-+
-+static void bcm2708_fb_imageblit(struct fb_info *info,
-+ const struct fb_image *image)
-+{
-+ /* (is called) print_debug("bcm2708_fb_imageblit\n"); */
-+ cfb_imageblit(info, image);
-+}
-+
-+static irqreturn_t bcm2708_fb_dma_irq(int irq, void *cxt)
-+{
-+ struct bcm2708_fb *fb = cxt;
-+
-+ /* FIXME: should read status register to check if this is
-+ * actually interrupting us or not, in case this interrupt
-+ * ever becomes shared amongst several DMA channels
-+ *
-+ * readl(dma_chan_base + BCM2708_DMA_CS) & BCM2708_DMA_IRQ;
-+ */
-+
-+ /* acknowledge the interrupt */
-+ writel(BCM2708_DMA_INT, fb->dma_chan_base + BCM2708_DMA_CS);
-+
-+ wake_up(&fb->dma_waitq);
-+ return IRQ_HANDLED;
-+}
-+
-+static struct fb_ops bcm2708_fb_ops = {
-+ .owner = THIS_MODULE,
-+ .fb_check_var = bcm2708_fb_check_var,
-+ .fb_set_par = bcm2708_fb_set_par,
-+ .fb_setcolreg = bcm2708_fb_setcolreg,
-+ .fb_blank = bcm2708_fb_blank,
-+ .fb_fillrect = bcm2708_fb_fillrect,
-+ .fb_copyarea = bcm2708_fb_copyarea,
-+ .fb_imageblit = bcm2708_fb_imageblit,
-+ .fb_pan_display = bcm2708_fb_pan_display,
-+ .fb_ioctl = bcm2708_ioctl,
-+};
-+
-+static int bcm2708_fb_register(struct bcm2708_fb *fb)
-+{
-+ int ret;
-+
-+ fb->fb.fbops = &bcm2708_fb_ops;
-+ fb->fb.flags = FBINFO_FLAG_DEFAULT | FBINFO_HWACCEL_COPYAREA;
-+ fb->fb.pseudo_palette = fb->cmap;
-+
-+ strncpy(fb->fb.fix.id, bcm2708_name, sizeof(fb->fb.fix.id));
-+ fb->fb.fix.type = FB_TYPE_PACKED_PIXELS;
-+ fb->fb.fix.type_aux = 0;
-+ fb->fb.fix.xpanstep = 1;
-+ fb->fb.fix.ypanstep = 1;
-+ fb->fb.fix.ywrapstep = 0;
-+ fb->fb.fix.accel = FB_ACCEL_NONE;
-+
-+ fb->fb.var.xres = fbwidth;
-+ fb->fb.var.yres = fbheight;
-+ fb->fb.var.xres_virtual = fbwidth;
-+ fb->fb.var.yres_virtual = fbheight;
-+ fb->fb.var.bits_per_pixel = fbdepth;
-+ fb->fb.var.vmode = FB_VMODE_NONINTERLACED;
-+ fb->fb.var.activate = FB_ACTIVATE_NOW;
-+ fb->fb.var.nonstd = 0;
-+ fb->fb.var.height = -1; /* height of picture in mm */
-+ fb->fb.var.width = -1; /* width of picture in mm */
-+ fb->fb.var.accel_flags = 0;
-+
-+ fb->fb.monspecs.hfmin = 0;
-+ fb->fb.monspecs.hfmax = 100000;
-+ fb->fb.monspecs.vfmin = 0;
-+ fb->fb.monspecs.vfmax = 400;
-+ fb->fb.monspecs.dclkmin = 1000000;
-+ fb->fb.monspecs.dclkmax = 100000000;
-+
-+ bcm2708_fb_set_bitfields(&fb->fb.var);
-+ init_waitqueue_head(&fb->dma_waitq);
-+
-+ /*
-+ * Allocate colourmap.
-+ */
-+
-+ fb_set_var(&fb->fb, &fb->fb.var);
-+ ret = bcm2708_fb_set_par(&fb->fb);
-+ if (ret)
-+ return ret;
-+
-+ print_debug("BCM2708FB: registering framebuffer (%dx%d@%d) (%d)\n", fbwidth,
-+ fbheight, fbdepth, fbswap);
-+
-+ ret = register_framebuffer(&fb->fb);
-+ print_debug("BCM2708FB: register framebuffer (%d)\n", ret);
-+ if (ret == 0)
-+ goto out;
-+
-+ print_debug("BCM2708FB: cannot register framebuffer (%d)\n", ret);
-+out:
-+ return ret;
-+}
-+
-+static int bcm2708_fb_probe(struct platform_device *dev)
-+{
-+ struct device_node *fw_np;
-+ struct rpi_firmware *fw;
-+ struct bcm2708_fb *fb;
-+ int ret;
-+
-+ fw_np = of_parse_phandle(dev->dev.of_node, "firmware", 0);
-+/* Remove comment when booting without Device Tree is no longer supported
-+ if (!fw_np) {
-+ dev_err(&dev->dev, "Missing firmware node\n");
-+ return -ENOENT;
-+ }
-+*/
-+ fw = rpi_firmware_get(fw_np);
-+ if (!fw)
-+ return -EPROBE_DEFER;
-+
-+ fb = kzalloc(sizeof(struct bcm2708_fb), GFP_KERNEL);
-+ if (!fb) {
-+ dev_err(&dev->dev,
-+ "could not allocate new bcm2708_fb struct\n");
-+ ret = -ENOMEM;
-+ goto free_region;
-+ }
-+
-+ fb->fw = fw;
-+ bcm2708_fb_debugfs_init(fb);
-+
-+ fb->cb_base = dma_alloc_writecombine(&dev->dev, SZ_64K,
-+ &fb->cb_handle, GFP_KERNEL);
-+ if (!fb->cb_base) {
-+ dev_err(&dev->dev, "cannot allocate DMA CBs\n");
-+ ret = -ENOMEM;
-+ goto free_fb;
-+ }
-+
-+ pr_info("BCM2708FB: allocated DMA memory %08x\n",
-+ fb->cb_handle);
-+
-+ ret = bcm_dma_chan_alloc(BCM_DMA_FEATURE_BULK,
-+ &fb->dma_chan_base, &fb->dma_irq);
-+ if (ret < 0) {
-+ dev_err(&dev->dev, "couldn't allocate a DMA channel\n");
-+ goto free_cb;
-+ }
-+ fb->dma_chan = ret;
-+
-+ ret = request_irq(fb->dma_irq, bcm2708_fb_dma_irq,
-+ 0, "bcm2708_fb dma", fb);
-+ if (ret) {
-+ pr_err("%s: failed to request DMA irq\n", __func__);
-+ goto free_dma_chan;
-+ }
-+
-+
-+ pr_info("BCM2708FB: allocated DMA channel %d @ %p\n",
-+ fb->dma_chan, fb->dma_chan_base);
-+
-+ fb->dev = dev;
-+ fb->fb.device = &dev->dev;
-+
-+ ret = bcm2708_fb_register(fb);
-+ if (ret == 0) {
-+ platform_set_drvdata(dev, fb);
-+ goto out;
-+ }
-+
-+free_dma_chan:
-+ bcm_dma_chan_free(fb->dma_chan);
-+free_cb:
-+ dma_free_writecombine(&dev->dev, SZ_64K, fb->cb_base, fb->cb_handle);
-+free_fb:
-+ kfree(fb);
-+free_region:
-+ dev_err(&dev->dev, "probe failed, err %d\n", ret);
-+out:
-+ return ret;
-+}
-+
-+static int bcm2708_fb_remove(struct platform_device *dev)
-+{
-+ struct bcm2708_fb *fb = platform_get_drvdata(dev);
-+
-+ platform_set_drvdata(dev, NULL);
-+
-+ if (fb->fb.screen_base)
-+ iounmap(fb->fb.screen_base);
-+ unregister_framebuffer(&fb->fb);
-+
-+ dma_free_writecombine(&dev->dev, SZ_64K, fb->cb_base, fb->cb_handle);
-+ bcm_dma_chan_free(fb->dma_chan);
-+
-+ bcm2708_fb_debugfs_deinit(fb);
-+
-+ free_irq(fb->dma_irq, fb);
-+
-+ kfree(fb);
-+
-+ return 0;
-+}
-+
-+static const struct of_device_id bcm2708_fb_of_match_table[] = {
-+ { .compatible = "brcm,bcm2708-fb", },
-+ {},
-+};
-+MODULE_DEVICE_TABLE(of, bcm2708_fb_of_match_table);
-+
-+static struct platform_driver bcm2708_fb_driver = {
-+ .probe = bcm2708_fb_probe,
-+ .remove = bcm2708_fb_remove,
-+ .driver = {
-+ .name = DRIVER_NAME,
-+ .owner = THIS_MODULE,
-+ .of_match_table = bcm2708_fb_of_match_table,
-+ },
-+};
-+
-+static int __init bcm2708_fb_init(void)
-+{
-+ return platform_driver_register(&bcm2708_fb_driver);
-+}
-+
-+module_init(bcm2708_fb_init);
-+
-+static void __exit bcm2708_fb_exit(void)
-+{
-+ platform_driver_unregister(&bcm2708_fb_driver);
-+}
-+
-+module_exit(bcm2708_fb_exit);
-+
-+module_param(fbwidth, int, 0644);
-+module_param(fbheight, int, 0644);
-+module_param(fbdepth, int, 0644);
-+module_param(fbswap, int, 0644);
-+
-+MODULE_DESCRIPTION("BCM2708 framebuffer driver");
-+MODULE_LICENSE("GPL");
-+
-+MODULE_PARM_DESC(fbwidth, "Width of ARM Framebuffer");
-+MODULE_PARM_DESC(fbheight, "Height of ARM Framebuffer");
-+MODULE_PARM_DESC(fbdepth, "Bit depth of ARM Framebuffer");
-+MODULE_PARM_DESC(fbswap, "Swap order of red and blue in 24 and 32 bit modes");
---- a/drivers/video/logo/logo_linux_clut224.ppm
-+++ b/drivers/video/logo/logo_linux_clut224.ppm
-@@ -1,1604 +1,883 @@
- P3
--# Standard 224-color Linux logo
--80 80
-+63 80
- 255
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 6 6 6 6 6 6 10 10 10 10 10 10
-- 10 10 10 6 6 6 6 6 6 6 6 6
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 6 6 6 10 10 10 14 14 14
-- 22 22 22 26 26 26 30 30 30 34 34 34
-- 30 30 30 30 30 30 26 26 26 18 18 18
-- 14 14 14 10 10 10 6 6 6 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 1 0 0 1 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 6 6 6 14 14 14 26 26 26 42 42 42
-- 54 54 54 66 66 66 78 78 78 78 78 78
-- 78 78 78 74 74 74 66 66 66 54 54 54
-- 42 42 42 26 26 26 18 18 18 10 10 10
-- 6 6 6 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 1 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 10 10 10
-- 22 22 22 42 42 42 66 66 66 86 86 86
-- 66 66 66 38 38 38 38 38 38 22 22 22
-- 26 26 26 34 34 34 54 54 54 66 66 66
-- 86 86 86 70 70 70 46 46 46 26 26 26
-- 14 14 14 6 6 6 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 1 0 0 1 0 0 1 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 10 10 10 26 26 26
-- 50 50 50 82 82 82 58 58 58 6 6 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 6 6 6 54 54 54 86 86 86 66 66 66
-- 38 38 38 18 18 18 6 6 6 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 6 6 6 22 22 22 50 50 50
-- 78 78 78 34 34 34 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 6 6 6 70 70 70
-- 78 78 78 46 46 46 22 22 22 6 6 6
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 1 0 0 1 0 0 1 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 6 6 6 18 18 18 42 42 42 82 82 82
-- 26 26 26 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 14 14 14
-- 46 46 46 34 34 34 6 6 6 2 2 6
-- 42 42 42 78 78 78 42 42 42 18 18 18
-- 6 6 6 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 1 0 0 0 0 0 1 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 10 10 10 30 30 30 66 66 66 58 58 58
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 26 26 26
-- 86 86 86 101 101 101 46 46 46 10 10 10
-- 2 2 6 58 58 58 70 70 70 34 34 34
-- 10 10 10 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 1 0 0 1 0 0 1 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 14 14 14 42 42 42 86 86 86 10 10 10
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 30 30 30
-- 94 94 94 94 94 94 58 58 58 26 26 26
-- 2 2 6 6 6 6 78 78 78 54 54 54
-- 22 22 22 6 6 6 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 6 6 6
-- 22 22 22 62 62 62 62 62 62 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 26 26 26
-- 54 54 54 38 38 38 18 18 18 10 10 10
-- 2 2 6 2 2 6 34 34 34 82 82 82
-- 38 38 38 14 14 14 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 1 0 0 1 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 6 6 6
-- 30 30 30 78 78 78 30 30 30 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 10 10 10
-- 10 10 10 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 78 78 78
-- 50 50 50 18 18 18 6 6 6 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 1 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 10 10 10
-- 38 38 38 86 86 86 14 14 14 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 54 54 54
-- 66 66 66 26 26 26 6 6 6 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 1 0 0 1 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 14 14 14
-- 42 42 42 82 82 82 2 2 6 2 2 6
-- 2 2 6 6 6 6 10 10 10 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 6 6 6
-- 14 14 14 10 10 10 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 18 18 18
-- 82 82 82 34 34 34 10 10 10 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 1 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 14 14 14
-- 46 46 46 86 86 86 2 2 6 2 2 6
-- 6 6 6 6 6 6 22 22 22 34 34 34
-- 6 6 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 18 18 18 34 34 34
-- 10 10 10 50 50 50 22 22 22 2 2 6
-- 2 2 6 2 2 6 2 2 6 10 10 10
-- 86 86 86 42 42 42 14 14 14 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 1 0 0 1 0 0 1 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 14 14 14
-- 46 46 46 86 86 86 2 2 6 2 2 6
-- 38 38 38 116 116 116 94 94 94 22 22 22
-- 22 22 22 2 2 6 2 2 6 2 2 6
-- 14 14 14 86 86 86 138 138 138 162 162 162
--154 154 154 38 38 38 26 26 26 6 6 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 86 86 86 46 46 46 14 14 14 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 14 14 14
-- 46 46 46 86 86 86 2 2 6 14 14 14
--134 134 134 198 198 198 195 195 195 116 116 116
-- 10 10 10 2 2 6 2 2 6 6 6 6
--101 98 89 187 187 187 210 210 210 218 218 218
--214 214 214 134 134 134 14 14 14 6 6 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 86 86 86 50 50 50 18 18 18 6 6 6
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 1 0 0 0
-- 0 0 1 0 0 1 0 0 1 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 14 14 14
-- 46 46 46 86 86 86 2 2 6 54 54 54
--218 218 218 195 195 195 226 226 226 246 246 246
-- 58 58 58 2 2 6 2 2 6 30 30 30
--210 210 210 253 253 253 174 174 174 123 123 123
--221 221 221 234 234 234 74 74 74 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 70 70 70 58 58 58 22 22 22 6 6 6
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 14 14 14
-- 46 46 46 82 82 82 2 2 6 106 106 106
--170 170 170 26 26 26 86 86 86 226 226 226
--123 123 123 10 10 10 14 14 14 46 46 46
--231 231 231 190 190 190 6 6 6 70 70 70
-- 90 90 90 238 238 238 158 158 158 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 70 70 70 58 58 58 22 22 22 6 6 6
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 1 0 0 0
-- 0 0 1 0 0 1 0 0 1 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 14 14 14
-- 42 42 42 86 86 86 6 6 6 116 116 116
--106 106 106 6 6 6 70 70 70 149 149 149
--128 128 128 18 18 18 38 38 38 54 54 54
--221 221 221 106 106 106 2 2 6 14 14 14
-- 46 46 46 190 190 190 198 198 198 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 74 74 74 62 62 62 22 22 22 6 6 6
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 1 0 0 0
-- 0 0 1 0 0 0 0 0 1 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 14 14 14
-- 42 42 42 94 94 94 14 14 14 101 101 101
--128 128 128 2 2 6 18 18 18 116 116 116
--118 98 46 121 92 8 121 92 8 98 78 10
--162 162 162 106 106 106 2 2 6 2 2 6
-- 2 2 6 195 195 195 195 195 195 6 6 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 74 74 74 62 62 62 22 22 22 6 6 6
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 1 0 0 1
-- 0 0 1 0 0 0 0 0 1 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 10 10 10
-- 38 38 38 90 90 90 14 14 14 58 58 58
--210 210 210 26 26 26 54 38 6 154 114 10
--226 170 11 236 186 11 225 175 15 184 144 12
--215 174 15 175 146 61 37 26 9 2 2 6
-- 70 70 70 246 246 246 138 138 138 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 70 70 70 66 66 66 26 26 26 6 6 6
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 10 10 10
-- 38 38 38 86 86 86 14 14 14 10 10 10
--195 195 195 188 164 115 192 133 9 225 175 15
--239 182 13 234 190 10 232 195 16 232 200 30
--245 207 45 241 208 19 232 195 16 184 144 12
--218 194 134 211 206 186 42 42 42 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 50 50 50 74 74 74 30 30 30 6 6 6
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 10 10 10
-- 34 34 34 86 86 86 14 14 14 2 2 6
--121 87 25 192 133 9 219 162 10 239 182 13
--236 186 11 232 195 16 241 208 19 244 214 54
--246 218 60 246 218 38 246 215 20 241 208 19
--241 208 19 226 184 13 121 87 25 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 50 50 50 82 82 82 34 34 34 10 10 10
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 10 10 10
-- 34 34 34 82 82 82 30 30 30 61 42 6
--180 123 7 206 145 10 230 174 11 239 182 13
--234 190 10 238 202 15 241 208 19 246 218 74
--246 218 38 246 215 20 246 215 20 246 215 20
--226 184 13 215 174 15 184 144 12 6 6 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 26 26 26 94 94 94 42 42 42 14 14 14
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 10 10 10
-- 30 30 30 78 78 78 50 50 50 104 69 6
--192 133 9 216 158 10 236 178 12 236 186 11
--232 195 16 241 208 19 244 214 54 245 215 43
--246 215 20 246 215 20 241 208 19 198 155 10
--200 144 11 216 158 10 156 118 10 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 6 6 6 90 90 90 54 54 54 18 18 18
-- 6 6 6 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 10 10 10
-- 30 30 30 78 78 78 46 46 46 22 22 22
--137 92 6 210 162 10 239 182 13 238 190 10
--238 202 15 241 208 19 246 215 20 246 215 20
--241 208 19 203 166 17 185 133 11 210 150 10
--216 158 10 210 150 10 102 78 10 2 2 6
-- 6 6 6 54 54 54 14 14 14 2 2 6
-- 2 2 6 62 62 62 74 74 74 30 30 30
-- 10 10 10 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 10 10 10
-- 34 34 34 78 78 78 50 50 50 6 6 6
-- 94 70 30 139 102 15 190 146 13 226 184 13
--232 200 30 232 195 16 215 174 15 190 146 13
--168 122 10 192 133 9 210 150 10 213 154 11
--202 150 34 182 157 106 101 98 89 2 2 6
-- 2 2 6 78 78 78 116 116 116 58 58 58
-- 2 2 6 22 22 22 90 90 90 46 46 46
-- 18 18 18 6 6 6 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 10 10 10
-- 38 38 38 86 86 86 50 50 50 6 6 6
--128 128 128 174 154 114 156 107 11 168 122 10
--198 155 10 184 144 12 197 138 11 200 144 11
--206 145 10 206 145 10 197 138 11 188 164 115
--195 195 195 198 198 198 174 174 174 14 14 14
-- 2 2 6 22 22 22 116 116 116 116 116 116
-- 22 22 22 2 2 6 74 74 74 70 70 70
-- 30 30 30 10 10 10 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 6 6 6 18 18 18
-- 50 50 50 101 101 101 26 26 26 10 10 10
--138 138 138 190 190 190 174 154 114 156 107 11
--197 138 11 200 144 11 197 138 11 192 133 9
--180 123 7 190 142 34 190 178 144 187 187 187
--202 202 202 221 221 221 214 214 214 66 66 66
-- 2 2 6 2 2 6 50 50 50 62 62 62
-- 6 6 6 2 2 6 10 10 10 90 90 90
-- 50 50 50 18 18 18 6 6 6 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 10 10 10 34 34 34
-- 74 74 74 74 74 74 2 2 6 6 6 6
--144 144 144 198 198 198 190 190 190 178 166 146
--154 121 60 156 107 11 156 107 11 168 124 44
--174 154 114 187 187 187 190 190 190 210 210 210
--246 246 246 253 253 253 253 253 253 182 182 182
-- 6 6 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 62 62 62
-- 74 74 74 34 34 34 14 14 14 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 10 10 10 22 22 22 54 54 54
-- 94 94 94 18 18 18 2 2 6 46 46 46
--234 234 234 221 221 221 190 190 190 190 190 190
--190 190 190 187 187 187 187 187 187 190 190 190
--190 190 190 195 195 195 214 214 214 242 242 242
--253 253 253 253 253 253 253 253 253 253 253 253
-- 82 82 82 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 14 14 14
-- 86 86 86 54 54 54 22 22 22 6 6 6
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 6 6 6 18 18 18 46 46 46 90 90 90
-- 46 46 46 18 18 18 6 6 6 182 182 182
--253 253 253 246 246 246 206 206 206 190 190 190
--190 190 190 190 190 190 190 190 190 190 190 190
--206 206 206 231 231 231 250 250 250 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--202 202 202 14 14 14 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 42 42 42 86 86 86 42 42 42 18 18 18
-- 6 6 6 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 6 6 6
-- 14 14 14 38 38 38 74 74 74 66 66 66
-- 2 2 6 6 6 6 90 90 90 250 250 250
--253 253 253 253 253 253 238 238 238 198 198 198
--190 190 190 190 190 190 195 195 195 221 221 221
--246 246 246 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 82 82 82 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 78 78 78 70 70 70 34 34 34
-- 14 14 14 6 6 6 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 14 14 14
-- 34 34 34 66 66 66 78 78 78 6 6 6
-- 2 2 6 18 18 18 218 218 218 253 253 253
--253 253 253 253 253 253 253 253 253 246 246 246
--226 226 226 231 231 231 246 246 246 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 178 178 178 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 18 18 18 90 90 90 62 62 62
-- 30 30 30 10 10 10 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 10 10 10 26 26 26
-- 58 58 58 90 90 90 18 18 18 2 2 6
-- 2 2 6 110 110 110 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--250 250 250 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 231 231 231 18 18 18 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 18 18 18 94 94 94
-- 54 54 54 26 26 26 10 10 10 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 6 6 6 22 22 22 50 50 50
-- 90 90 90 26 26 26 2 2 6 2 2 6
-- 14 14 14 195 195 195 250 250 250 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--250 250 250 242 242 242 54 54 54 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 38 38 38
-- 86 86 86 50 50 50 22 22 22 6 6 6
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 6 6 6 14 14 14 38 38 38 82 82 82
-- 34 34 34 2 2 6 2 2 6 2 2 6
-- 42 42 42 195 195 195 246 246 246 253 253 253
--253 253 253 253 253 253 253 253 253 250 250 250
--242 242 242 242 242 242 250 250 250 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 250 250 250 246 246 246 238 238 238
--226 226 226 231 231 231 101 101 101 6 6 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 38 38 38 82 82 82 42 42 42 14 14 14
-- 6 6 6 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 10 10 10 26 26 26 62 62 62 66 66 66
-- 2 2 6 2 2 6 2 2 6 6 6 6
-- 70 70 70 170 170 170 206 206 206 234 234 234
--246 246 246 250 250 250 250 250 250 238 238 238
--226 226 226 231 231 231 238 238 238 250 250 250
--250 250 250 250 250 250 246 246 246 231 231 231
--214 214 214 206 206 206 202 202 202 202 202 202
--198 198 198 202 202 202 182 182 182 18 18 18
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 62 62 62 66 66 66 30 30 30
-- 10 10 10 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 14 14 14 42 42 42 82 82 82 18 18 18
-- 2 2 6 2 2 6 2 2 6 10 10 10
-- 94 94 94 182 182 182 218 218 218 242 242 242
--250 250 250 253 253 253 253 253 253 250 250 250
--234 234 234 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 246 246 246
--238 238 238 226 226 226 210 210 210 202 202 202
--195 195 195 195 195 195 210 210 210 158 158 158
-- 6 6 6 14 14 14 50 50 50 14 14 14
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 6 6 6 86 86 86 46 46 46
-- 18 18 18 6 6 6 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 6 6 6
-- 22 22 22 54 54 54 70 70 70 2 2 6
-- 2 2 6 10 10 10 2 2 6 22 22 22
--166 166 166 231 231 231 250 250 250 253 253 253
--253 253 253 253 253 253 253 253 253 250 250 250
--242 242 242 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 246 246 246
--231 231 231 206 206 206 198 198 198 226 226 226
-- 94 94 94 2 2 6 6 6 6 38 38 38
-- 30 30 30 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 62 62 62 66 66 66
-- 26 26 26 10 10 10 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 10 10 10
-- 30 30 30 74 74 74 50 50 50 2 2 6
-- 26 26 26 26 26 26 2 2 6 106 106 106
--238 238 238 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 246 246 246 218 218 218 202 202 202
--210 210 210 14 14 14 2 2 6 2 2 6
-- 30 30 30 22 22 22 2 2 6 2 2 6
-- 2 2 6 2 2 6 18 18 18 86 86 86
-- 42 42 42 14 14 14 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 14 14 14
-- 42 42 42 90 90 90 22 22 22 2 2 6
-- 42 42 42 2 2 6 18 18 18 218 218 218
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 250 250 250 221 221 221
--218 218 218 101 101 101 2 2 6 14 14 14
-- 18 18 18 38 38 38 10 10 10 2 2 6
-- 2 2 6 2 2 6 2 2 6 78 78 78
-- 58 58 58 22 22 22 6 6 6 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 6 6 6 18 18 18
-- 54 54 54 82 82 82 2 2 6 26 26 26
-- 22 22 22 2 2 6 123 123 123 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 250 250 250
--238 238 238 198 198 198 6 6 6 38 38 38
-- 58 58 58 26 26 26 38 38 38 2 2 6
-- 2 2 6 2 2 6 2 2 6 46 46 46
-- 78 78 78 30 30 30 10 10 10 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 10 10 10 30 30 30
-- 74 74 74 58 58 58 2 2 6 42 42 42
-- 2 2 6 22 22 22 231 231 231 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 250 250 250
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 246 246 246 46 46 46 38 38 38
-- 42 42 42 14 14 14 38 38 38 14 14 14
-- 2 2 6 2 2 6 2 2 6 6 6 6
-- 86 86 86 46 46 46 14 14 14 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 6 6 6 14 14 14 42 42 42
-- 90 90 90 18 18 18 18 18 18 26 26 26
-- 2 2 6 116 116 116 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 250 250 250 238 238 238
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 94 94 94 6 6 6
-- 2 2 6 2 2 6 10 10 10 34 34 34
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 74 74 74 58 58 58 22 22 22 6 6 6
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 10 10 10 26 26 26 66 66 66
-- 82 82 82 2 2 6 38 38 38 6 6 6
-- 14 14 14 210 210 210 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 246 246 246 242 242 242
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 144 144 144 2 2 6
-- 2 2 6 2 2 6 2 2 6 46 46 46
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 42 42 42 74 74 74 30 30 30 10 10 10
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 6 6 6 14 14 14 42 42 42 90 90 90
-- 26 26 26 6 6 6 42 42 42 2 2 6
-- 74 74 74 250 250 250 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 242 242 242 242 242 242
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 182 182 182 2 2 6
-- 2 2 6 2 2 6 2 2 6 46 46 46
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 10 10 10 86 86 86 38 38 38 10 10 10
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 10 10 10 26 26 26 66 66 66 82 82 82
-- 2 2 6 22 22 22 18 18 18 2 2 6
--149 149 149 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 234 234 234 242 242 242
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 206 206 206 2 2 6
-- 2 2 6 2 2 6 2 2 6 38 38 38
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 6 6 6 86 86 86 46 46 46 14 14 14
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 6 6 6
-- 18 18 18 46 46 46 86 86 86 18 18 18
-- 2 2 6 34 34 34 10 10 10 6 6 6
--210 210 210 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 234 234 234 242 242 242
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 221 221 221 6 6 6
-- 2 2 6 2 2 6 6 6 6 30 30 30
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 82 82 82 54 54 54 18 18 18
-- 6 6 6 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 10 10 10
-- 26 26 26 66 66 66 62 62 62 2 2 6
-- 2 2 6 38 38 38 10 10 10 26 26 26
--238 238 238 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 231 231 231 238 238 238
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 231 231 231 6 6 6
-- 2 2 6 2 2 6 10 10 10 30 30 30
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 66 66 66 58 58 58 22 22 22
-- 6 6 6 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 10 10 10
-- 38 38 38 78 78 78 6 6 6 2 2 6
-- 2 2 6 46 46 46 14 14 14 42 42 42
--246 246 246 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 231 231 231 242 242 242
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 234 234 234 10 10 10
-- 2 2 6 2 2 6 22 22 22 14 14 14
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 66 66 66 62 62 62 22 22 22
-- 6 6 6 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 6 6 6 18 18 18
-- 50 50 50 74 74 74 2 2 6 2 2 6
-- 14 14 14 70 70 70 34 34 34 62 62 62
--250 250 250 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 231 231 231 246 246 246
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 234 234 234 14 14 14
-- 2 2 6 2 2 6 30 30 30 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 66 66 66 62 62 62 22 22 22
-- 6 6 6 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 6 6 6 18 18 18
-- 54 54 54 62 62 62 2 2 6 2 2 6
-- 2 2 6 30 30 30 46 46 46 70 70 70
--250 250 250 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 231 231 231 246 246 246
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 226 226 226 10 10 10
-- 2 2 6 6 6 6 30 30 30 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 66 66 66 58 58 58 22 22 22
-- 6 6 6 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 6 6 6 22 22 22
-- 58 58 58 62 62 62 2 2 6 2 2 6
-- 2 2 6 2 2 6 30 30 30 78 78 78
--250 250 250 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 231 231 231 246 246 246
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 206 206 206 2 2 6
-- 22 22 22 34 34 34 18 14 6 22 22 22
-- 26 26 26 18 18 18 6 6 6 2 2 6
-- 2 2 6 82 82 82 54 54 54 18 18 18
-- 6 6 6 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 6 6 6 26 26 26
-- 62 62 62 106 106 106 74 54 14 185 133 11
--210 162 10 121 92 8 6 6 6 62 62 62
--238 238 238 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 231 231 231 246 246 246
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 158 158 158 18 18 18
-- 14 14 14 2 2 6 2 2 6 2 2 6
-- 6 6 6 18 18 18 66 66 66 38 38 38
-- 6 6 6 94 94 94 50 50 50 18 18 18
-- 6 6 6 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 6 6 6
-- 10 10 10 10 10 10 18 18 18 38 38 38
-- 78 78 78 142 134 106 216 158 10 242 186 14
--246 190 14 246 190 14 156 118 10 10 10 10
-- 90 90 90 238 238 238 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 231 231 231 250 250 250
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 246 230 190
--238 204 91 238 204 91 181 142 44 37 26 9
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 38 38 38 46 46 46
-- 26 26 26 106 106 106 54 54 54 18 18 18
-- 6 6 6 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 6 6 6 14 14 14 22 22 22
-- 30 30 30 38 38 38 50 50 50 70 70 70
--106 106 106 190 142 34 226 170 11 242 186 14
--246 190 14 246 190 14 246 190 14 154 114 10
-- 6 6 6 74 74 74 226 226 226 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 231 231 231 250 250 250
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 228 184 62
--241 196 14 241 208 19 232 195 16 38 30 10
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 6 6 6 30 30 30 26 26 26
--203 166 17 154 142 90 66 66 66 26 26 26
-- 6 6 6 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 6 6 6 18 18 18 38 38 38 58 58 58
-- 78 78 78 86 86 86 101 101 101 123 123 123
--175 146 61 210 150 10 234 174 13 246 186 14
--246 190 14 246 190 14 246 190 14 238 190 10
--102 78 10 2 2 6 46 46 46 198 198 198
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 234 234 234 242 242 242
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 224 178 62
--242 186 14 241 196 14 210 166 10 22 18 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 6 6 6 121 92 8
--238 202 15 232 195 16 82 82 82 34 34 34
-- 10 10 10 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 14 14 14 38 38 38 70 70 70 154 122 46
--190 142 34 200 144 11 197 138 11 197 138 11
--213 154 11 226 170 11 242 186 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--225 175 15 46 32 6 2 2 6 22 22 22
--158 158 158 250 250 250 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 250 250 250 242 242 242 224 178 62
--239 182 13 236 186 11 213 154 11 46 32 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 61 42 6 225 175 15
--238 190 10 236 186 11 112 100 78 42 42 42
-- 14 14 14 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 6 6 6
-- 22 22 22 54 54 54 154 122 46 213 154 11
--226 170 11 230 174 11 226 170 11 226 170 11
--236 178 12 242 186 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--241 196 14 184 144 12 10 10 10 2 2 6
-- 6 6 6 116 116 116 242 242 242 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 231 231 231 198 198 198 214 170 54
--236 178 12 236 178 12 210 150 10 137 92 6
-- 18 14 6 2 2 6 2 2 6 2 2 6
-- 6 6 6 70 47 6 200 144 11 236 178 12
--239 182 13 239 182 13 124 112 88 58 58 58
-- 22 22 22 6 6 6 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 10 10 10
-- 30 30 30 70 70 70 180 133 36 226 170 11
--239 182 13 242 186 14 242 186 14 246 186 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 232 195 16 98 70 6 2 2 6
-- 2 2 6 2 2 6 66 66 66 221 221 221
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 206 206 206 198 198 198 214 166 58
--230 174 11 230 174 11 216 158 10 192 133 9
--163 110 8 116 81 8 102 78 10 116 81 8
--167 114 7 197 138 11 226 170 11 239 182 13
--242 186 14 242 186 14 162 146 94 78 78 78
-- 34 34 34 14 14 14 6 6 6 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 6 6 6
-- 30 30 30 78 78 78 190 142 34 226 170 11
--239 182 13 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 241 196 14 203 166 17 22 18 6
-- 2 2 6 2 2 6 2 2 6 38 38 38
--218 218 218 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--250 250 250 206 206 206 198 198 198 202 162 69
--226 170 11 236 178 12 224 166 10 210 150 10
--200 144 11 197 138 11 192 133 9 197 138 11
--210 150 10 226 170 11 242 186 14 246 190 14
--246 190 14 246 186 14 225 175 15 124 112 88
-- 62 62 62 30 30 30 14 14 14 6 6 6
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 10 10 10
-- 30 30 30 78 78 78 174 135 50 224 166 10
--239 182 13 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 241 196 14 139 102 15
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 78 78 78 250 250 250 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--250 250 250 214 214 214 198 198 198 190 150 46
--219 162 10 236 178 12 234 174 13 224 166 10
--216 158 10 213 154 11 213 154 11 216 158 10
--226 170 11 239 182 13 246 190 14 246 190 14
--246 190 14 246 190 14 242 186 14 206 162 42
--101 101 101 58 58 58 30 30 30 14 14 14
-- 6 6 6 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 10 10 10
-- 30 30 30 74 74 74 174 135 50 216 158 10
--236 178 12 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 241 196 14 226 184 13
-- 61 42 6 2 2 6 2 2 6 2 2 6
-- 22 22 22 238 238 238 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 226 226 226 187 187 187 180 133 36
--216 158 10 236 178 12 239 182 13 236 178 12
--230 174 11 226 170 11 226 170 11 230 174 11
--236 178 12 242 186 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 186 14 239 182 13
--206 162 42 106 106 106 66 66 66 34 34 34
-- 14 14 14 6 6 6 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 6 6 6
-- 26 26 26 70 70 70 163 133 67 213 154 11
--236 178 12 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 241 196 14
--190 146 13 18 14 6 2 2 6 2 2 6
-- 46 46 46 246 246 246 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 221 221 221 86 86 86 156 107 11
--216 158 10 236 178 12 242 186 14 246 186 14
--242 186 14 239 182 13 239 182 13 242 186 14
--242 186 14 246 186 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--242 186 14 225 175 15 142 122 72 66 66 66
-- 30 30 30 10 10 10 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 6 6 6
-- 26 26 26 70 70 70 163 133 67 210 150 10
--236 178 12 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--232 195 16 121 92 8 34 34 34 106 106 106
--221 221 221 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--242 242 242 82 82 82 18 14 6 163 110 8
--216 158 10 236 178 12 242 186 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 242 186 14 163 133 67
-- 46 46 46 18 18 18 6 6 6 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 10 10 10
-- 30 30 30 78 78 78 163 133 67 210 150 10
--236 178 12 246 186 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--241 196 14 215 174 15 190 178 144 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 218 218 218
-- 58 58 58 2 2 6 22 18 6 167 114 7
--216 158 10 236 178 12 246 186 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 186 14 242 186 14 190 150 46
-- 54 54 54 22 22 22 6 6 6 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 14 14 14
-- 38 38 38 86 86 86 180 133 36 213 154 11
--236 178 12 246 186 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 232 195 16 190 146 13 214 214 214
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 250 250 250 170 170 170 26 26 26
-- 2 2 6 2 2 6 37 26 9 163 110 8
--219 162 10 239 182 13 246 186 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 186 14 236 178 12 224 166 10 142 122 72
-- 46 46 46 18 18 18 6 6 6 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 6 6 6 18 18 18
-- 50 50 50 109 106 95 192 133 9 224 166 10
--242 186 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--242 186 14 226 184 13 210 162 10 142 110 46
--226 226 226 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--253 253 253 253 253 253 253 253 253 253 253 253
--198 198 198 66 66 66 2 2 6 2 2 6
-- 2 2 6 2 2 6 50 34 6 156 107 11
--219 162 10 239 182 13 246 186 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 242 186 14
--234 174 13 213 154 11 154 122 46 66 66 66
-- 30 30 30 10 10 10 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 6 6 6 22 22 22
-- 58 58 58 154 121 60 206 145 10 234 174 13
--242 186 14 246 186 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 186 14 236 178 12 210 162 10 163 110 8
-- 61 42 6 138 138 138 218 218 218 250 250 250
--253 253 253 253 253 253 253 253 253 250 250 250
--242 242 242 210 210 210 144 144 144 66 66 66
-- 6 6 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 61 42 6 163 110 8
--216 158 10 236 178 12 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 239 182 13 230 174 11 216 158 10
--190 142 34 124 112 88 70 70 70 38 38 38
-- 18 18 18 6 6 6 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 6 6 6 22 22 22
-- 62 62 62 168 124 44 206 145 10 224 166 10
--236 178 12 239 182 13 242 186 14 242 186 14
--246 186 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 236 178 12 216 158 10 175 118 6
-- 80 54 7 2 2 6 6 6 6 30 30 30
-- 54 54 54 62 62 62 50 50 50 38 38 38
-- 14 14 14 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 6 6 6 80 54 7 167 114 7
--213 154 11 236 178 12 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 190 14 242 186 14 239 182 13 239 182 13
--230 174 11 210 150 10 174 135 50 124 112 88
-- 82 82 82 54 54 54 34 34 34 18 18 18
-- 6 6 6 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 6 6 6 18 18 18
-- 50 50 50 158 118 36 192 133 9 200 144 11
--216 158 10 219 162 10 224 166 10 226 170 11
--230 174 11 236 178 12 239 182 13 239 182 13
--242 186 14 246 186 14 246 190 14 246 190 14
--246 190 14 246 190 14 246 190 14 246 190 14
--246 186 14 230 174 11 210 150 10 163 110 8
--104 69 6 10 10 10 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 6 6 6 91 60 6 167 114 7
--206 145 10 230 174 11 242 186 14 246 190 14
--246 190 14 246 190 14 246 186 14 242 186 14
--239 182 13 230 174 11 224 166 10 213 154 11
--180 133 36 124 112 88 86 86 86 58 58 58
-- 38 38 38 22 22 22 10 10 10 6 6 6
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 14 14 14
-- 34 34 34 70 70 70 138 110 50 158 118 36
--167 114 7 180 123 7 192 133 9 197 138 11
--200 144 11 206 145 10 213 154 11 219 162 10
--224 166 10 230 174 11 239 182 13 242 186 14
--246 186 14 246 186 14 246 186 14 246 186 14
--239 182 13 216 158 10 185 133 11 152 99 6
--104 69 6 18 14 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 2 2 6 2 2 6 2 2 6
-- 2 2 6 6 6 6 80 54 7 152 99 6
--192 133 9 219 162 10 236 178 12 239 182 13
--246 186 14 242 186 14 239 182 13 236 178 12
--224 166 10 206 145 10 192 133 9 154 121 60
-- 94 94 94 62 62 62 42 42 42 22 22 22
-- 14 14 14 6 6 6 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 6 6 6
-- 18 18 18 34 34 34 58 58 58 78 78 78
--101 98 89 124 112 88 142 110 46 156 107 11
--163 110 8 167 114 7 175 118 6 180 123 7
--185 133 11 197 138 11 210 150 10 219 162 10
--226 170 11 236 178 12 236 178 12 234 174 13
--219 162 10 197 138 11 163 110 8 130 83 6
-- 91 60 6 10 10 10 2 2 6 2 2 6
-- 18 18 18 38 38 38 38 38 38 38 38 38
-- 38 38 38 38 38 38 38 38 38 38 38 38
-- 38 38 38 38 38 38 26 26 26 2 2 6
-- 2 2 6 6 6 6 70 47 6 137 92 6
--175 118 6 200 144 11 219 162 10 230 174 11
--234 174 13 230 174 11 219 162 10 210 150 10
--192 133 9 163 110 8 124 112 88 82 82 82
-- 50 50 50 30 30 30 14 14 14 6 6 6
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 6 6 6 14 14 14 22 22 22 34 34 34
-- 42 42 42 58 58 58 74 74 74 86 86 86
--101 98 89 122 102 70 130 98 46 121 87 25
--137 92 6 152 99 6 163 110 8 180 123 7
--185 133 11 197 138 11 206 145 10 200 144 11
--180 123 7 156 107 11 130 83 6 104 69 6
-- 50 34 6 54 54 54 110 110 110 101 98 89
-- 86 86 86 82 82 82 78 78 78 78 78 78
-- 78 78 78 78 78 78 78 78 78 78 78 78
-- 78 78 78 82 82 82 86 86 86 94 94 94
--106 106 106 101 101 101 86 66 34 124 80 6
--156 107 11 180 123 7 192 133 9 200 144 11
--206 145 10 200 144 11 192 133 9 175 118 6
--139 102 15 109 106 95 70 70 70 42 42 42
-- 22 22 22 10 10 10 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 6 6 6 10 10 10
-- 14 14 14 22 22 22 30 30 30 38 38 38
-- 50 50 50 62 62 62 74 74 74 90 90 90
--101 98 89 112 100 78 121 87 25 124 80 6
--137 92 6 152 99 6 152 99 6 152 99 6
--138 86 6 124 80 6 98 70 6 86 66 30
--101 98 89 82 82 82 58 58 58 46 46 46
-- 38 38 38 34 34 34 34 34 34 34 34 34
-- 34 34 34 34 34 34 34 34 34 34 34 34
-- 34 34 34 34 34 34 38 38 38 42 42 42
-- 54 54 54 82 82 82 94 86 76 91 60 6
--134 86 6 156 107 11 167 114 7 175 118 6
--175 118 6 167 114 7 152 99 6 121 87 25
--101 98 89 62 62 62 34 34 34 18 18 18
-- 6 6 6 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 6 6 6 6 6 6 10 10 10
-- 18 18 18 22 22 22 30 30 30 42 42 42
-- 50 50 50 66 66 66 86 86 86 101 98 89
--106 86 58 98 70 6 104 69 6 104 69 6
--104 69 6 91 60 6 82 62 34 90 90 90
-- 62 62 62 38 38 38 22 22 22 14 14 14
-- 10 10 10 10 10 10 10 10 10 10 10 10
-- 10 10 10 10 10 10 6 6 6 10 10 10
-- 10 10 10 10 10 10 10 10 10 14 14 14
-- 22 22 22 42 42 42 70 70 70 89 81 66
-- 80 54 7 104 69 6 124 80 6 137 92 6
--134 86 6 116 81 8 100 82 52 86 86 86
-- 58 58 58 30 30 30 14 14 14 6 6 6
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 6 6 6 10 10 10 14 14 14
-- 18 18 18 26 26 26 38 38 38 54 54 54
-- 70 70 70 86 86 86 94 86 76 89 81 66
-- 89 81 66 86 86 86 74 74 74 50 50 50
-- 30 30 30 14 14 14 6 6 6 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 6 6 6 18 18 18 34 34 34 58 58 58
-- 82 82 82 89 81 66 89 81 66 89 81 66
-- 94 86 66 94 86 76 74 74 74 50 50 50
-- 26 26 26 14 14 14 6 6 6 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 6 6 6 6 6 6 14 14 14 18 18 18
-- 30 30 30 38 38 38 46 46 46 54 54 54
-- 50 50 50 42 42 42 30 30 30 18 18 18
-- 10 10 10 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 6 6 6 14 14 14 26 26 26
-- 38 38 38 50 50 50 58 58 58 58 58 58
-- 54 54 54 42 42 42 30 30 30 18 18 18
-- 10 10 10 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 6 6 6
-- 6 6 6 10 10 10 14 14 14 18 18 18
-- 18 18 18 14 14 14 10 10 10 6 6 6
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 6 6 6
-- 14 14 14 18 18 18 22 22 22 22 22 22
-- 18 18 18 14 14 14 10 10 10 6 6 6
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-- 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 1 0
-+0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0 0
-+0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0
-+10 15 3 2 3 1 12 18 4 42 61 14 19 27 6 11 16 4
-+38 55 13 10 15 3 3 4 1 10 15 3 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 3 1
-+12 18 4 1 1 0 23 34 8 31 45 11 10 15 3 32 47 11
-+34 49 12 3 4 1 3 4 1 3 4 1 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 10 15 3 29 42 10 26 37 9 12 18 4
-+55 80 19 81 118 28 55 80 19 92 132 31 106 153 36 69 100 23
-+100 144 34 80 116 27 42 61 14 81 118 28 23 34 8 27 40 9
-+15 21 5 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 1 1 0 29 42 10 15 21 5 50 72 17
-+74 107 25 45 64 15 102 148 35 80 116 27 84 121 28 111 160 38
-+69 100 23 65 94 22 81 118 28 29 42 10 17 25 6 29 42 10
-+23 34 8 2 3 1 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 4 1
-+15 21 5 15 21 5 34 49 12 101 146 34 111 161 38 97 141 33
-+97 141 33 119 172 41 117 170 40 116 167 40 118 170 40 118 171 40
-+117 169 40 118 170 40 111 160 38 118 170 40 96 138 32 89 128 30
-+81 118 28 11 16 4 10 15 3 1 1 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+3 4 1 3 4 1 34 49 12 101 146 34 79 115 27 111 160 38
-+114 165 39 113 163 39 118 170 40 117 169 40 118 171 40 117 169 40
-+116 167 40 119 172 41 113 163 39 92 132 31 105 151 36 113 163 39
-+75 109 26 19 27 6 16 23 5 11 16 4 0 1 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 10 15 3
-+80 116 27 106 153 36 105 151 36 114 165 39 118 170 40 118 171 40
-+118 171 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 170 40 117 169 40 118 170 40 118 170 40
-+117 170 40 75 109 26 75 109 26 34 49 12 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 4 1
-+64 92 22 65 94 22 100 144 34 118 171 40 118 170 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 118 171 41 118 170 40 117 169 40
-+109 158 37 105 151 36 104 150 35 47 69 16 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+42 61 14 115 167 39 118 170 40 117 169 40 117 169 40 117 169 40
-+117 170 40 117 170 40 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 117 169 40 118 170 40 96 138 32 17 25 6 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 47 69 16
-+114 165 39 117 168 40 117 170 40 117 169 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 117 169 40 118 170 40 117 169 40 117 169 40 117 169 40
-+117 170 40 119 172 41 96 138 32 12 18 4 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 10 15 3
-+32 47 11 105 151 36 118 170 40 117 169 40 117 169 40 116 168 40
-+109 157 37 111 160 38 117 169 40 118 171 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 118 171 40 69 100 23 2 3 1
-+0 0 0 0 0 0 0 0 0 0 0 0 19 27 6 101 146 34
-+118 171 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 170 40
-+118 171 40 115 166 39 107 154 36 111 161 38 117 169 40 117 169 40
-+117 169 40 118 171 40 75 109 26 19 27 6 2 3 1 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 16 23 5
-+89 128 30 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+111 160 38 92 132 31 79 115 27 96 138 32 115 166 39 119 171 41
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 118 170 40 109 157 37 26 37 9
-+0 0 0 0 0 0 0 0 0 0 0 0 64 92 22 118 171 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 118 170 40 118 171 40 109 157 37
-+89 128 30 81 118 28 100 144 34 115 166 39 117 169 40 117 169 40
-+117 169 40 117 170 40 113 163 39 60 86 20 1 1 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+27 40 9 96 138 32 118 170 40 117 169 40 117 169 40 117 169 40
-+117 170 40 117 169 40 101 146 34 67 96 23 55 80 19 84 121 28
-+113 163 39 119 171 41 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 119 171 41 65 94 22
-+0 0 0 0 0 0 0 0 0 15 21 5 101 146 34 118 171 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 118 170 40 118 171 40 104 150 35 69 100 23 53 76 18
-+81 118 28 111 160 38 118 170 40 117 169 40 117 169 40 117 169 40
-+117 169 40 114 165 39 69 100 23 10 15 3 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0
-+31 45 11 77 111 26 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 117 169 40 118 170 40 116 168 40 92 132 31 47 69 16
-+38 55 13 81 118 28 113 163 39 119 171 41 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 118 171 41 92 132 31
-+10 15 3 0 0 0 0 0 0 36 52 12 115 166 39 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 118 170 40
-+118 171 40 102 148 35 64 92 22 34 49 12 65 94 22 106 153 36
-+118 171 40 117 170 40 117 169 40 117 169 40 117 169 40 117 169 40
-+118 170 40 107 154 36 55 80 19 15 21 5 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+29 42 10 101 146 34 118 171 40 117 169 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 118 171 40 113 163 39
-+75 109 26 27 40 9 36 52 12 89 128 30 116 167 40 118 171 40
-+117 169 40 117 169 40 117 169 40 117 169 40 118 170 40 104 150 35
-+16 23 5 0 0 0 0 0 0 53 76 18 118 171 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 119 171 41 109 157 37
-+67 96 23 23 34 8 42 61 14 96 138 32 118 170 40 118 170 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 117 169 40 74 107 25 10 15 3 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 31 45 11 101 146 34 118 170 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+119 171 41 102 148 35 47 69 16 14 20 5 50 72 17 102 148 35
-+118 171 40 117 169 40 117 169 40 117 169 40 118 170 40 102 148 35
-+15 21 5 0 0 0 0 0 0 50 72 17 118 170 40 117 169 40
-+117 169 40 117 169 40 118 170 40 116 167 40 84 121 28 27 40 9
-+19 27 6 74 107 25 114 165 39 118 171 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 75 109 26 10 15 4 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 38 55 13 102 148 35 118 171 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 118 170 40 115 167 39 77 111 26 17 25 6 19 27 6
-+77 111 26 115 166 39 118 170 40 117 169 40 119 172 41 81 118 28
-+3 4 1 0 0 0 0 0 0 27 40 9 111 160 38 118 170 40
-+117 169 40 118 171 40 105 151 36 50 72 17 10 15 3 38 55 13
-+100 144 34 118 171 40 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 79 115 27 15 21 5 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 10 15 3 64 92 22 111 160 38 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 118 171 40 96 138 32 32 47 11
-+3 4 1 50 72 17 107 154 36 120 173 41 105 151 36 31 45 11
-+0 0 0 0 0 0 0 0 0 3 4 1 65 94 22 117 169 40
-+118 170 40 89 128 30 26 37 9 3 4 1 60 86 20 111 161 38
-+118 171 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+97 141 33 36 52 12 1 1 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 14 20 5 75 109 26 117 168 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 118 171 40 107 154 36
-+45 64 15 2 3 1 31 45 11 75 109 26 32 47 11 0 1 0
-+0 0 0 0 0 0 0 0 0 0 0 0 10 15 3 55 80 19
-+65 94 22 11 16 4 11 16 4 75 109 26 116 168 40 118 170 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 118 170 40 107 154 36
-+47 69 16 3 4 1 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 12 18 4 69 100 23 111 161 38 118 171 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 118 170 40
-+111 160 38 50 72 17 2 3 1 2 3 1 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0
-+1 1 0 12 18 4 81 118 28 118 170 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 170 40 118 171 40 101 146 34
-+42 61 14 2 3 1 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 3 4 1 36 52 12 89 128 30
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+118 171 41 101 146 34 14 20 5 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 47 69 16 118 170 40 117 169 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 170 40 111 160 38 69 100 23 19 27 6
-+0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 11 16 4 69 100 23
-+115 167 39 119 172 41 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+119 172 41 75 109 26 3 4 1 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 23 34 8 106 153 36 118 170 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+117 169 40 118 170 40 119 172 41 105 151 36 42 61 14 2 3 1
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 15 21 5
-+45 64 15 80 116 27 114 165 39 118 170 40 117 169 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 119 172 41
-+97 141 33 20 30 7 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 1 1 0 53 76 18 114 165 39 118 171 40 117 169 40
-+117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40
-+118 171 40 104 150 35 64 92 22 31 45 11 10 15 3 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 36 52 12 97 141 33 109 158 37 113 163 39 116 168 40
-+117 169 40 117 170 40 118 170 40 119 172 41 115 167 39 84 121 28
-+23 34 8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 3 4 1 50 72 17 102 148 35 118 171 40
-+119 171 41 118 170 40 117 169 40 117 169 40 115 166 39 111 161 38
-+109 157 37 79 115 27 12 18 4 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 3 4 1 15 21 5 23 34 8 45 64 15 106 153 36
-+116 167 40 111 160 38 101 146 34 79 115 27 42 61 14 10 15 3
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 1 1 0 20 30 7 60 86 20
-+89 128 30 106 153 36 113 163 39 117 169 40 84 121 28 29 42 10
-+19 27 6 10 15 3 2 3 1 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 16 23 5 38 55 13
-+36 52 12 26 37 9 12 18 4 2 3 1 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 1 0 0 19 2 7 52 5 18
-+78 7 27 88 8 31 81 7 29 56 5 19 25 2 9 3 0 1
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+3 4 1 19 27 6 31 45 11 38 55 13 32 47 11 3 4 1
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 0 1
-+9 0 3 12 1 4 9 0 3 4 0 1 0 0 0 0 0 0
-+0 0 0 0 0 0 28 3 10 99 9 35 156 14 55 182 16 64
-+189 17 66 190 17 67 189 17 66 184 17 65 166 15 58 118 13 41
-+45 4 16 3 0 1 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 11 1 4 52 5 18 101 9 35 134 12 47
-+151 14 53 154 14 54 151 14 53 113 10 40 11 1 4 0 0 0
-+3 0 1 67 6 24 159 14 56 190 17 67 190 17 67 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 190 17 67 191 17 67
-+174 16 61 101 9 35 14 1 5 0 0 0 35 3 12 108 10 38
-+122 11 43 122 11 43 112 10 39 87 8 30 50 5 17 13 1 5
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+3 0 1 56 5 19 141 13 49 182 16 64 191 17 67 191 17 67
-+190 17 67 190 17 67 191 17 67 113 10 40 3 0 1 1 0 0
-+79 7 28 180 16 63 190 17 67 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+189 17 66 188 17 66 122 11 43 11 1 4 41 4 14 176 16 62
-+191 17 67 191 17 67 191 17 67 190 17 67 181 16 63 146 13 51
-+75 7 26 10 1 4 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 7 1 2
-+90 8 32 178 16 62 191 17 67 188 17 66 188 17 66 188 17 66
-+188 17 66 190 17 67 141 13 49 22 2 8 0 0 0 41 4 14
-+173 16 61 190 17 67 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 88 8 31 1 0 0 89 8 31
-+185 17 65 189 17 66 188 17 66 188 17 66 189 17 66 191 17 67
-+186 17 65 124 11 43 25 2 9 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 2 0 1 89 8 31
-+184 17 65 189 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+190 17 67 151 14 53 34 3 12 0 0 0 0 0 0 79 7 28
-+190 17 67 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 191 17 67 146 13 51 9 1 3 7 1 2
-+108 10 38 187 17 66 189 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 190 17 67 141 13 49 22 2 8 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 52 5 18 176 16 62
-+189 17 66 188 17 66 188 17 66 188 17 66 188 17 66 190 17 67
-+151 14 53 38 3 13 0 0 0 0 0 0 0 0 0 50 5 17
-+180 16 63 189 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 191 17 67 141 13 49 7 1 3 0 0 0
-+11 1 4 112 10 39 187 17 66 189 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 190 17 67 113 10 40 5 0 2 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 7 1 3 132 12 46 191 17 67
-+188 17 66 188 17 66 188 17 66 188 17 66 190 17 67 146 13 51
-+35 3 12 0 0 0 0 0 0 0 0 0 0 0 0 5 0 2
-+101 9 35 185 17 65 190 17 67 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 190 17 67 180 16 63 67 6 24 0 0 0 0 0 0
-+0 0 0 11 1 4 108 10 38 186 17 65 189 17 66 188 17 66
-+188 17 66 188 17 66 189 17 66 180 16 63 56 5 19 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 44 4 15 177 16 62 189 17 66
-+188 17 66 188 17 66 189 17 66 189 17 66 134 12 47 28 3 10
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+8 1 3 79 7 28 159 14 56 188 17 66 191 17 67 190 17 67
-+189 17 66 189 17 66 189 17 66 189 17 66 190 17 67 191 17 67
-+188 17 66 158 14 55 72 7 25 4 0 1 0 0 0 0 0 0
-+0 0 0 0 0 0 8 1 3 95 9 33 182 16 64 189 17 67
-+188 17 66 188 17 66 188 17 66 191 17 67 122 11 43 3 0 1
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 88 8 31 190 17 67 188 17 66
-+188 17 66 189 17 66 185 17 65 113 10 40 18 2 6 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 1 0 0 24 2 8 77 7 27 124 11 43 154 14 54
-+168 15 59 173 16 61 173 16 61 168 15 59 154 14 54 124 11 43
-+77 7 27 22 2 8 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 5 0 2 77 7 27 173 16 61
-+190 17 67 188 17 66 188 17 66 190 17 67 164 15 57 23 2 8
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 1 0 0 118 13 41 191 17 67 188 17 66
-+190 17 67 174 16 61 87 8 30 8 1 3 0 0 0 0 0 0
-+0 0 0 0 0 0 10 1 4 29 3 10 40 4 14 36 3 13
-+18 2 6 2 0 1 0 0 0 0 0 0 3 0 1 14 1 5
-+26 2 9 33 3 11 32 3 11 25 2 9 13 1 5 3 0 1
-+0 0 0 14 1 5 56 5 19 95 9 33 109 10 38 101 9 35
-+77 7 27 35 3 12 5 0 2 0 0 0 1 0 0 56 5 19
-+156 14 55 190 17 67 188 17 66 188 17 66 182 16 64 50 5 17
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 5 0 2 134 12 47 191 17 67 189 17 66
-+151 14 53 52 5 18 2 0 1 0 0 0 0 0 0 1 0 0
-+28 3 10 90 8 32 146 13 51 170 15 60 178 16 62 174 16 61
-+158 14 55 112 10 39 40 4 14 1 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 0 1
-+56 5 19 146 13 51 183 17 64 191 17 67 191 17 67 191 17 67
-+188 17 66 173 16 61 122 11 43 41 4 14 1 0 0 0 0 0
-+30 3 10 124 11 43 185 17 65 190 17 67 187 17 66 67 6 24
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 6 1 2 134 12 47 168 15 59 99 9 35
-+21 2 7 0 0 0 0 0 0 0 0 0 6 1 2 77 7 27
-+162 15 57 190 17 67 191 17 67 189 17 66 189 17 66 189 17 66
-+190 17 67 191 17 67 169 15 59 75 7 26 3 0 1 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 2 0 1 79 7 28
-+178 16 62 191 17 67 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 189 17 66 191 17 67 170 15 60 79 7 28 5 0 2
-+0 0 0 10 1 3 78 7 27 159 14 56 188 17 66 75 7 26
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 1 0 0 35 3 12 29 3 10 2 0 1
-+0 0 0 0 0 0 0 0 0 9 1 3 101 9 35 183 17 64
-+190 17 67 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 190 17 67 178 16 63 67 6 23 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 52 5 18 174 16 61
-+190 17 67 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 190 17 67 182 16 64 89 8 31
-+4 0 1 0 0 0 0 0 0 25 2 9 73 7 26 31 3 11
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 4 0 1 98 9 34 187 17 66 189 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 190 17 67 158 14 55 25 2 9
-+0 0 0 0 0 0 0 0 0 8 1 3 134 12 47 191 17 67
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 189 17 66 180 16 63
-+68 6 24 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 6 1 2 19 2 7 3 0 1 0 0 0 0 0 0
-+0 0 0 0 0 0 65 6 23 180 16 63 189 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 189 17 66 83 8 29
-+0 0 0 0 0 0 0 0 0 41 4 14 177 16 62 189 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 190 17 67
-+159 14 56 28 3 10 0 0 0 0 0 0 0 0 0 23 2 8
-+41 4 14 5 0 2 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+23 2 8 113 10 40 159 14 56 65 6 23 0 0 0 0 0 0
-+0 0 0 16 1 6 146 13 51 191 17 67 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 191 17 67 132 12 46
-+5 0 2 0 0 0 0 0 0 77 7 27 189 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+190 17 67 98 9 34 0 0 0 0 0 0 12 1 4 134 12 47
-+178 16 63 108 10 38 16 1 6 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 30 3 10
-+141 13 49 190 17 67 191 17 67 134 12 47 6 1 2 0 0 0
-+0 0 0 68 6 24 186 17 65 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 190 17 67 156 14 55
-+14 1 5 0 0 0 0 0 0 98 9 34 191 17 67 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+190 17 67 156 14 55 19 2 7 0 0 0 47 4 16 181 16 63
-+190 17 67 189 17 66 126 14 44 17 2 6 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 16 1 6 134 12 47
-+191 17 67 188 17 66 190 17 67 162 15 57 19 2 7 0 0 0
-+3 0 1 123 11 43 191 17 67 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 190 17 67 163 15 57
-+20 2 7 0 0 0 0 0 0 101 9 35 191 17 67 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 182 16 64 52 5 18 0 0 0 73 7 26 188 17 66
-+188 17 66 188 17 66 189 17 66 109 10 38 5 0 2 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 95 9 33 189 17 66
-+188 17 66 188 17 66 189 17 66 171 15 60 29 3 10 0 0 0
-+16 1 6 156 14 55 190 17 67 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 190 17 67 158 14 55
-+17 2 6 0 0 0 0 0 0 85 8 30 190 17 67 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 189 17 66 81 7 29 0 0 0 85 8 30 190 17 67
-+188 17 66 188 17 66 189 17 66 180 16 63 56 5 19 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 25 2 9 162 15 57 190 17 67
-+188 17 66 188 17 66 189 17 66 173 16 61 31 3 11 0 0 0
-+30 3 10 171 15 60 189 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 191 17 67 141 13 49
-+7 1 2 0 0 0 0 0 0 56 5 19 183 17 64 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 191 17 67 98 9 34 0 0 0 88 8 31 190 17 67
-+188 17 66 188 17 66 188 17 66 191 17 67 124 11 43 5 0 2
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 68 6 24 187 17 66 188 17 66
-+188 17 66 188 17 66 189 17 66 170 15 60 28 3 10 0 0 0
-+34 3 12 174 16 61 189 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 191 17 67 101 9 35
-+0 0 0 0 0 0 0 0 0 21 2 7 159 14 56 190 17 67
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 191 17 67 98 9 34 0 0 0 81 7 29 189 17 66
-+188 17 66 188 17 66 188 17 66 189 17 66 168 15 59 28 3 10
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 109 10 38 191 17 67 188 17 66
-+188 17 66 188 17 66 190 17 67 163 15 57 21 2 7 0 0 0
-+26 2 9 168 15 59 189 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 189 17 66 180 16 63 47 4 16
-+0 0 0 0 0 0 0 0 0 0 0 0 108 10 38 190 17 67
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 189 17 66 78 7 27 0 0 0 68 6 24 187 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 183 17 64 56 5 19
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 3 0 1 131 12 46 191 17 67 188 17 66
-+188 17 66 188 17 66 190 17 67 151 14 53 12 1 4 0 0 0
-+11 1 4 146 13 51 190 17 67 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 191 17 67 126 14 44 7 1 2
-+0 0 0 0 0 0 0 0 0 0 0 0 32 3 11 164 15 58
-+190 17 67 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+189 17 66 178 16 62 44 4 15 0 0 0 50 5 17 182 16 64
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 72 7 25
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 5 0 2 134 12 47 191 17 67 188 17 66
-+188 17 66 188 17 66 191 17 67 131 12 46 3 0 1 0 0 0
-+0 0 0 101 9 35 190 17 67 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 190 17 67 170 15 60 44 4 15 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 77 7 27
-+183 17 64 189 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+191 17 67 134 12 47 9 1 3 0 0 0 31 3 11 171 15 60
-+189 17 66 188 17 66 188 17 66 188 17 66 188 17 66 72 7 25
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 2 0 1 124 11 43 191 17 67 188 17 66
-+188 17 66 188 17 66 191 17 67 101 9 35 0 0 0 0 0 0
-+0 0 0 35 3 12 168 15 59 190 17 67 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 189 17 66 182 16 64 77 7 27 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 6 1 2
-+99 9 35 185 17 65 189 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 189 17 66
-+177 16 62 56 5 19 0 0 0 0 0 0 13 1 5 151 14 53
-+190 17 67 188 17 66 188 17 66 188 17 66 185 17 65 56 5 19
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 99 9 35 191 17 67 188 17 66
-+188 17 66 188 17 66 186 17 65 65 6 23 0 0 0 0 0 0
-+0 0 0 0 0 0 79 7 28 182 16 64 190 17 67 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+191 17 67 177 16 62 83 8 29 4 0 1 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+8 1 3 89 8 31 175 16 62 191 17 67 189 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 190 17 67 181 16 63
-+85 8 30 3 0 1 0 0 0 0 0 0 1 0 0 118 13 41
-+191 17 67 188 17 66 188 17 66 189 17 66 173 16 61 34 3 12
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 56 5 19 183 17 64 188 17 66
-+188 17 66 189 17 66 169 15 59 30 3 10 0 0 0 0 0 0
-+0 0 0 0 0 0 5 0 2 83 8 29 173 16 61 191 17 67
-+190 17 67 189 17 66 189 17 66 190 17 67 191 17 67 187 17 66
-+151 14 53 56 5 19 3 0 1 0 0 0 16 1 6 50 5 17
-+79 7 28 95 9 33 95 9 33 75 7 26 41 4 14 10 1 4
-+0 0 0 2 0 1 50 5 17 132 12 46 178 16 62 190 17 67
-+191 17 67 191 17 67 191 17 67 186 17 65 154 14 54 68 6 24
-+4 0 1 0 0 0 0 0 0 0 0 0 0 0 0 72 7 25
-+187 17 66 188 17 66 188 17 66 191 17 67 141 13 49 9 1 3
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 14 1 5 151 14 53 190 17 67
-+188 17 66 191 17 67 131 12 46 5 0 2 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 2 0 1 44 4 15 113 10 40
-+156 14 55 173 16 61 174 16 61 164 15 58 134 12 47 77 7 27
-+18 2 6 0 0 0 16 1 6 85 8 30 151 14 53 182 16 64
-+189 17 66 191 17 67 190 17 67 188 17 66 177 16 62 141 13 49
-+68 6 24 8 1 3 0 0 0 8 1 3 44 4 15 88 8 31
-+113 10 40 122 11 43 108 10 38 67 6 24 20 2 7 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 28 3 10
-+166 15 58 190 17 67 188 17 66 187 17 66 79 7 28 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 73 7 26 185 17 65
-+189 17 66 184 17 65 65 6 23 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 0 1
-+17 2 6 32 3 11 34 3 12 22 2 8 6 1 2 0 0 0
-+0 0 0 38 3 13 141 13 49 188 17 66 190 17 67 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 189 17 66 191 17 67
-+184 17 65 122 11 43 21 2 7 0 0 0 0 0 0 0 0 0
-+0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0
-+108 10 38 191 17 67 191 17 67 141 13 49 16 1 6 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 8 1 3 112 10 39
-+186 17 65 124 11 43 10 1 4 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+36 3 13 156 14 55 191 17 67 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+189 17 66 190 17 67 134 12 47 18 2 6 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 7 1 2 41 4 14 75 7 26 66 5 23 19 2 7
-+26 2 9 144 13 50 154 14 54 40 4 14 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 13 1 5
-+56 5 19 19 2 7 0 0 0 7 1 2 29 3 10 35 3 12
-+19 2 7 2 0 1 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 13 1 5
-+134 12 47 191 17 67 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 189 17 67 108 10 38 3 0 1 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0
-+40 4 14 124 11 43 177 16 62 188 17 66 187 17 66 144 13 50
-+24 2 8 17 2 6 22 2 8 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 19 2 7 122 11 43 171 15 60 175 16 62
-+159 14 56 112 10 39 40 4 14 2 0 1 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 72 7 25
-+186 17 65 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 189 17 66 174 16 61 41 4 14 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 3 0 1 72 7 25
-+168 15 59 191 17 67 189 17 66 188 17 66 188 17 66 190 17 67
-+95 9 33 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 95 9 33 191 17 67 189 17 66 189 17 66
-+190 17 67 191 17 67 171 15 60 90 8 32 12 1 4 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 5 0 2 132 12 46
-+191 17 67 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 190 17 67 98 9 34 0 0 0
-+0 0 0 0 0 0 0 0 0 5 0 2 88 8 31 180 16 63
-+190 17 67 188 17 66 188 17 66 188 17 66 188 17 66 191 17 67
-+146 13 51 11 1 4 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 9 1 3 144 13 50 191 17 67 188 17 66 188 17 66
-+188 17 66 188 17 66 189 17 66 187 17 66 123 11 43 20 2 7
-+0 0 0 0 0 0 0 0 0 0 0 0 21 2 7 163 15 57
-+190 17 67 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 191 17 67 134 12 47 5 0 2
-+0 0 0 0 0 0 3 0 1 88 8 31 182 16 64 189 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 189 17 66
-+171 15 60 31 3 11 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 20 2 7 162 15 57 190 17 67 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 190 17 67 132 12 46
-+20 2 7 0 0 0 0 0 0 0 0 0 32 3 11 173 16 61
-+189 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 190 17 67 151 14 53 12 1 4
-+0 0 0 0 0 0 72 7 25 180 16 63 189 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+181 16 63 47 4 16 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 21 2 7 163 15 57 190 17 67 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 190 17 67
-+122 11 43 9 1 3 0 0 0 0 0 0 30 3 10 171 15 60
-+189 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 190 17 67 146 13 51 10 1 4
-+0 0 0 38 3 13 166 15 58 190 17 67 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+183 17 64 52 5 18 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 13 1 5 154 14 54 190 17 67 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+186 17 65 79 7 28 0 0 0 0 0 0 14 1 5 156 14 54
-+190 17 67 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 191 17 67 124 11 43 2 0 1
-+5 0 2 122 11 43 191 17 67 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+182 16 64 47 4 16 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 3 0 1 126 14 44 191 17 67 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+190 17 67 158 14 55 23 2 8 0 0 0 1 0 0 113 10 40
-+191 17 67 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 78 7 27 0 0 0
-+47 4 16 177 16 62 189 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 189 17 66
-+173 16 61 34 3 12 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 85 8 30 189 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 79 7 28 0 0 0 0 0 0 47 4 16
-+175 16 62 189 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 190 17 67 156 14 55 22 2 8 0 0 0
-+109 10 38 191 17 67 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 190 17 67
-+151 14 53 13 1 5 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 35 3 12 173 16 61 189 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 191 17 67 134 12 47 7 1 2 0 0 0 3 0 1
-+99 9 35 188 17 66 189 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 189 17 66 181 16 63 68 6 24 0 0 0 18 2 6
-+156 14 55 190 17 67 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 190 17 67
-+101 9 35 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 3 0 1 118 13 41 191 17 67 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 189 17 66 168 15 59 28 3 10 0 0 0 0 0 0
-+12 1 4 113 10 40 187 17 66 189 17 67 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+190 17 67 180 16 63 88 8 31 4 0 1 0 0 0 47 4 16
-+180 16 63 189 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 190 17 67 168 15 59
-+36 3 13 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 38 3 13 164 15 58 190 17 67
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 182 16 64 50 5 17 0 0 0 0 0 0
-+0 0 0 11 1 4 90 8 32 169 15 59 190 17 67 190 17 67
-+189 17 66 189 17 66 189 17 66 189 17 66 191 17 67 189 17 66
-+158 14 55 68 6 24 4 0 1 0 0 0 0 0 0 73 7 26
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 189 17 66 185 17 65 83 8 29
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 65 6 23 174 16 61
-+190 17 67 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 185 17 65 56 5 19 0 0 0 0 0 0
-+0 0 0 0 0 0 2 0 1 35 3 12 99 9 35 146 13 51
-+170 15 60 177 16 62 177 16 62 166 15 58 141 13 49 85 8 30
-+24 2 8 0 0 0 0 0 0 0 0 0 0 0 0 85 8 30
-+190 17 67 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 189 17 66 112 10 39 8 1 3
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 68 6 24
-+170 15 60 191 17 67 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 182 16 64 50 5 17 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 11 1 4
-+28 3 10 40 4 14 38 3 13 25 2 9 8 1 3 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 78 7 27
-+189 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 189 17 66 187 17 66 113 10 40 14 1 5 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0
-+47 4 16 141 13 49 186 17 65 191 17 67 190 17 67 189 17 66
-+189 17 66 191 17 67 156 14 55 20 2 7 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 44 4 15
-+178 16 62 190 17 67 188 17 66 188 17 66 188 17 66 190 17 67
-+191 17 67 173 16 61 90 8 32 10 1 4 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 14 1 5 68 6 24 131 12 46 162 15 57 174 16 61
-+171 15 60 146 13 51 56 5 19 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 3 0 1 14 1 5 29 3 10
-+41 4 14 47 4 16 50 5 17 45 4 16 34 3 12 18 2 6
-+5 0 2 0 0 0 0 0 0 0 0 0 0 0 0 5 0 2
-+90 8 32 169 15 59 185 17 65 187 17 66 182 16 64 163 15 57
-+113 10 40 41 4 14 2 0 1 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 5 0 2 21 2 7 34 3 12
-+29 3 10 11 1 4 0 0 0 0 0 0 0 0 0 0 0 0
-+3 0 1 32 3 11 79 7 28 124 11 43 154 14 54 171 15 60
-+180 16 63 182 16 64 182 16 64 180 16 63 174 16 61 159 14 56
-+132 12 46 88 8 31 34 3 12 3 0 1 0 0 0 0 0 0
-+3 0 1 29 3 10 56 5 19 65 6 23 50 5 17 23 2 8
-+3 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 25 2 9
-+109 10 38 169 15 59 189 17 66 191 17 67 190 17 67 189 17 66
-+189 17 66 188 17 66 188 17 66 188 17 66 189 17 66 190 17 67
-+191 17 67 190 17 67 171 15 60 98 9 34 10 1 3 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 14 1 5 141 13 49
-+191 17 67 189 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 189 17 67 186 17 65 65 6 23 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 23 2 8 166 15 58
-+190 17 67 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 189 17 66 176 16 62 45 4 16 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 83 8 29
-+183 17 64 189 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+188 17 66 189 17 66 185 17 65 95 9 33 3 0 1 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 5 0 2
-+85 8 30 176 16 62 191 17 67 188 17 66 188 17 66 188 17 66
-+188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66
-+191 17 67 180 16 63 95 9 33 7 1 3 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+2 0 1 52 5 18 141 13 49 185 17 65 191 17 67 189 17 67
-+189 17 66 188 17 66 188 17 66 189 17 66 191 17 67 187 17 66
-+146 13 51 56 5 19 4 0 1 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 14 1 5 68 6 24 131 12 46 166 15 58
-+180 16 63 183 17 64 180 16 63 168 15 59 134 12 47 75 7 26
-+17 2 6 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 5 0 2 24 2 8
-+44 4 15 52 5 18 45 4 16 26 2 9 6 1 2 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-+0 0 0 0 0 0 0 0 0
diff --git a/target/linux/brcm2708/patches-4.4/0031-dmaengine-Add-support-for-BCM2708.patch b/target/linux/brcm2708/patches-4.4/0031-dmaengine-Add-support-for-BCM2708.patch
deleted file mode 100644
index d444830..0000000
--- a/target/linux/brcm2708/patches-4.4/0031-dmaengine-Add-support-for-BCM2708.patch
+++ /dev/null
@@ -1,612 +0,0 @@
-From 659b118206dd29242abbb2d1f889b7b9788561f3 Mon Sep 17 00:00:00 2001
-From: Florian Meier <florian.meier at koalo.de>
-Date: Fri, 22 Nov 2013 14:22:53 +0100
-Subject: [PATCH] dmaengine: Add support for BCM2708
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Add support for DMA controller of BCM2708 as used in the Raspberry Pi.
-Currently it only supports cyclic DMA.
-
-Signed-off-by: Florian Meier <florian.meier at koalo.de>
-
-dmaengine: expand functionality by supporting scatter/gather transfers sdhci-bcm2708 and dma.c: fix for LITE channels
-
-DMA: fix cyclic LITE length overflow bug
-
-dmaengine: bcm2708: Remove chancnt affectations
-
-Mirror bcm2835-dma.c commit 9eba5536a7434c69d8c185d4bd1c70734d92287d:
-chancnt is already filled by dma_async_device_register, which uses the channel
-list to know how much channels there is.
-
-Since it's already filled, we can safely remove it from the drivers' probe
-function.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-dmaengine: bcm2708: overwrite dreq only if it is not set
-
-dreq is set when the DMA channel is fetched from Device Tree.
-slave_id is set using dmaengine_slave_config().
-Only overwrite dreq with slave_id if it is not set.
-
-dreq/slave_id in the cyclic DMA case is not touched, because I don't
-have hardware to test with.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-dmaengine: bcm2708: do device registration in the board file
-
-Don't register the device in the driver. Do it in the board file.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-dmaengine: bcm2708: don't restrict DT support to ARCH_BCM2835
-
-Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
-Add Device Tree support to the non ARCH_BCM2835 case.
-Use the same driver name regardless of architecture.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-BCM270x_DT: add bcm2835-dma entry
-
-Add Device Tree entry for bcm2835-dma.
-The entry doesn't contain any resources since they are handled
-by the arch/arm/mach-bcm270x/dma.c driver.
-In non-DT mode, don't add the device in the board file.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-bcm2708-dmaengine: Add debug options
-
-BCM270x: Add memory and irq resources to dmaengine device and DT
-
-Prepare for merging of the legacy DMA API arch driver dma.c
-with bcm2708-dmaengine by adding memory and irq resources both
-to platform file device and Device Tree node.
-Don't use BCM_DMAMAN_DRIVER_NAME so we don't have to include mach/dma.h
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-dmaengine: bcm2708: Merge with arch dma.c driver and disable dma.c
-
-Merge the legacy DMA API driver with bcm2708-dmaengine.
-This is done so we can use bcm2708_fb on ARCH_BCM2835 (mailbox
-driver is also needed).
-
-Changes to the dma.c code:
-- Use BIT() macro.
-- Cutdown some comments to one line.
-- Add mutex to vc_dmaman and use this, since the dev lock is locked
- during probing of the engine part.
-- Add global g_dmaman variable since drvdata is used by the engine part.
-- Restructure for readability:
- vc_dmaman_chan_alloc()
- vc_dmaman_chan_free()
- bcm_dma_chan_free()
-- Restructure bcm_dma_chan_alloc() to simplify error handling.
-- Use device irq resources instead of hardcoded bcm_dma_irqs table.
-- Remove dev_dmaman_register() and code it directly.
-- Remove dev_dmaman_deregister() and code it directly.
-- Simplify bcm_dmaman_probe() using devm_* functions.
-- Get dmachans from DT if available.
-- Keep 'dma.dmachans' module argument name for backwards compatibility.
-
-Make it available on ARCH_BCM2835 as well.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-dmaengine: bcm2708: set residue_granularity field
-
-bcm2708-dmaengine supports residue reporting at burst level
-but didn't report this via the residue_granularity field.
-
-Without this field set properly we get playback issues with I2S cards.
-
-dmaengine: bcm2708-dmaengine: Fix memory leak when stopping a running transfer
-
-bcm2708-dmaengine: Use more DMA channels (but not 12)
-
-1) Only the bcm2708_fb drivers uses the legacy DMA API, and
-it requires a BULK-capable channel, so all other types
-(FAST, NORMAL and LITE) can be made available to the regular
-DMA API.
-
-2) DMA channels 11-14 share an interrupt. The driver can't
-handle this, so don't use channels 12-14 (12 was used, probably
-because it appears to have an interrupt, but in reality that
-interrupt is for activity on ANY channel). This may explain
-a lockup encountered when running out of DMA channels.
-
-The combined effect of this patch is to leave 7 DMA channels
-available + channel 0 for bcm2708_fb via the legacy API.
-
-See: https://github.com/raspberrypi/linux/issues/1110
- https://github.com/raspberrypi/linux/issues/1108
-
-dmaengine: bcm2708: Make legacy API available for bcm2835-dma
-
-bcm2708_fb uses the legacy DMA API, so in order to start using
-bcm2835-dma, bcm2835-dma has to support the legacy API. Make this
-possible by exporting bcm_dmaman_probe() and bcm_dmaman_remove().
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-dmaengine: bcm2708: Change DT compatible string
-
-Both bcm2835-dma and bcm2708-dmaengine have the same compatible string.
-So change compatible to "brcm,bcm2708-dma".
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-dmaengine: bcm2708: Remove driver but keep legacy API
-
-Dropping non-DT support means we don't need this driver,
-but we still need the legacy DMA API.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
----
- drivers/dma/Kconfig | 4 +
- drivers/dma/Makefile | 1 +
- drivers/dma/bcm2708-dmaengine.c | 281 ++++++++++++++++++++++++++++++
- include/linux/platform_data/dma-bcm2708.h | 143 +++++++++++++++
- 4 files changed, 429 insertions(+)
- create mode 100644 drivers/dma/bcm2708-dmaengine.c
- create mode 100644 include/linux/platform_data/dma-bcm2708.h
-
---- a/drivers/dma/Kconfig
-+++ b/drivers/dma/Kconfig
-@@ -470,6 +470,10 @@ config TIMB_DMA
- help
- Enable support for the Timberdale FPGA DMA engine.
-
-+config DMA_BCM2708
-+ tristate "BCM2708 DMA legacy API support"
-+ depends on DMA_BCM2835
-+
- config TI_CPPI41
- tristate "AM33xx CPPI41 DMA support"
- depends on ARCH_OMAP
---- a/drivers/dma/Makefile
-+++ b/drivers/dma/Makefile
-@@ -18,6 +18,7 @@ obj-$(CONFIG_AT_HDMAC) += at_hdmac.o
- obj-$(CONFIG_AT_XDMAC) += at_xdmac.o
- obj-$(CONFIG_AXI_DMAC) += dma-axi-dmac.o
- obj-$(CONFIG_COH901318) += coh901318.o coh901318_lli.o
-+obj-$(CONFIG_DMA_BCM2708) += bcm2708-dmaengine.o
- obj-$(CONFIG_DMA_BCM2835) += bcm2835-dma.o
- obj-$(CONFIG_DMA_JZ4740) += dma-jz4740.o
- obj-$(CONFIG_DMA_JZ4780) += dma-jz4780.o
---- /dev/null
-+++ b/drivers/dma/bcm2708-dmaengine.c
-@@ -0,0 +1,281 @@
-+/*
-+ * BCM2708 legacy DMA API
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ */
-+
-+#include <linux/init.h>
-+#include <linux/interrupt.h>
-+#include <linux/list.h>
-+#include <linux/module.h>
-+#include <linux/platform_data/dma-bcm2708.h>
-+#include <linux/platform_device.h>
-+#include <linux/slab.h>
-+#include <linux/io.h>
-+#include <linux/spinlock.h>
-+
-+#include "virt-dma.h"
-+
-+#define CACHE_LINE_MASK 31
-+#define DEFAULT_DMACHAN_BITMAP 0x10 /* channel 4 only */
-+
-+/* valid only for channels 0 - 14, 15 has its own base address */
-+#define BCM2708_DMA_CHAN(n) ((n) << 8) /* base address */
-+#define BCM2708_DMA_CHANIO(dma_base, n) \
-+ ((void __iomem *)((char *)(dma_base) + BCM2708_DMA_CHAN(n)))
-+
-+struct vc_dmaman {
-+ void __iomem *dma_base;
-+ u32 chan_available; /* bitmap of available channels */
-+ u32 has_feature[BCM_DMA_FEATURE_COUNT]; /* bitmap of feature presence */
-+ struct mutex lock;
-+};
-+
-+static struct device *dmaman_dev; /* we assume there's only one! */
-+static struct vc_dmaman *g_dmaman; /* DMA manager */
-+
-+/* DMA Auxiliary Functions */
-+
-+/* A DMA buffer on an arbitrary boundary may separate a cache line into a
-+ section inside the DMA buffer and another section outside it.
-+ Even if we flush DMA buffers from the cache there is always the chance that
-+ during a DMA someone will access the part of a cache line that is outside
-+ the DMA buffer - which will then bring in unwelcome data.
-+ Without being able to dictate our own buffer pools we must insist that
-+ DMA buffers consist of a whole number of cache lines.
-+*/
-+extern int bcm_sg_suitable_for_dma(struct scatterlist *sg_ptr, int sg_len)
-+{
-+ int i;
-+
-+ for (i = 0; i < sg_len; i++) {
-+ if (sg_ptr[i].offset & CACHE_LINE_MASK ||
-+ sg_ptr[i].length & CACHE_LINE_MASK)
-+ return 0;
-+ }
-+
-+ return 1;
-+}
-+EXPORT_SYMBOL_GPL(bcm_sg_suitable_for_dma);
-+
-+extern void bcm_dma_start(void __iomem *dma_chan_base,
-+ dma_addr_t control_block)
-+{
-+ dsb(); /* ARM data synchronization (push) operation */
-+
-+ writel(control_block, dma_chan_base + BCM2708_DMA_ADDR);
-+ writel(BCM2708_DMA_ACTIVE, dma_chan_base + BCM2708_DMA_CS);
-+}
-+EXPORT_SYMBOL_GPL(bcm_dma_start);
-+
-+extern void bcm_dma_wait_idle(void __iomem *dma_chan_base)
-+{
-+ dsb();
-+
-+ /* ugly busy wait only option for now */
-+ while (readl(dma_chan_base + BCM2708_DMA_CS) & BCM2708_DMA_ACTIVE)
-+ cpu_relax();
-+}
-+EXPORT_SYMBOL_GPL(bcm_dma_wait_idle);
-+
-+extern bool bcm_dma_is_busy(void __iomem *dma_chan_base)
-+{
-+ dsb();
-+
-+ return readl(dma_chan_base + BCM2708_DMA_CS) & BCM2708_DMA_ACTIVE;
-+}
-+EXPORT_SYMBOL_GPL(bcm_dma_is_busy);
-+
-+/* Complete an ongoing DMA (assuming its results are to be ignored)
-+ Does nothing if there is no DMA in progress.
-+ This routine waits for the current AXI transfer to complete before
-+ terminating the current DMA. If the current transfer is hung on a DREQ used
-+ by an uncooperative peripheral the AXI transfer may never complete. In this
-+ case the routine times out and return a non-zero error code.
-+ Use of this routine doesn't guarantee that the ongoing or aborted DMA
-+ does not produce an interrupt.
-+*/
-+extern int bcm_dma_abort(void __iomem *dma_chan_base)
-+{
-+ unsigned long int cs;
-+ int rc = 0;
-+
-+ cs = readl(dma_chan_base + BCM2708_DMA_CS);
-+
-+ if (BCM2708_DMA_ACTIVE & cs) {
-+ long int timeout = 10000;
-+
-+ /* write 0 to the active bit - pause the DMA */
-+ writel(0, dma_chan_base + BCM2708_DMA_CS);
-+
-+ /* wait for any current AXI transfer to complete */
-+ while (0 != (cs & BCM2708_DMA_ISPAUSED) && --timeout >= 0)
-+ cs = readl(dma_chan_base + BCM2708_DMA_CS);
-+
-+ if (0 != (cs & BCM2708_DMA_ISPAUSED)) {
-+ /* we'll un-pause when we set of our next DMA */
-+ rc = -ETIMEDOUT;
-+
-+ } else if (BCM2708_DMA_ACTIVE & cs) {
-+ /* terminate the control block chain */
-+ writel(0, dma_chan_base + BCM2708_DMA_NEXTCB);
-+
-+ /* abort the whole DMA */
-+ writel(BCM2708_DMA_ABORT | BCM2708_DMA_ACTIVE,
-+ dma_chan_base + BCM2708_DMA_CS);
-+ }
-+ }
-+
-+ return rc;
-+}
-+EXPORT_SYMBOL_GPL(bcm_dma_abort);
-+
-+ /* DMA Manager Device Methods */
-+
-+static void vc_dmaman_init(struct vc_dmaman *dmaman, void __iomem *dma_base,
-+ u32 chans_available)
-+{
-+ dmaman->dma_base = dma_base;
-+ dmaman->chan_available = chans_available;
-+ dmaman->has_feature[BCM_DMA_FEATURE_FAST_ORD] = 0x0c; /* 2 & 3 */
-+ dmaman->has_feature[BCM_DMA_FEATURE_BULK_ORD] = 0x01; /* 0 */
-+ dmaman->has_feature[BCM_DMA_FEATURE_NORMAL_ORD] = 0xfe; /* 1 to 7 */
-+ dmaman->has_feature[BCM_DMA_FEATURE_LITE_ORD] = 0x7f00; /* 8 to 14 */
-+}
-+
-+static int vc_dmaman_chan_alloc(struct vc_dmaman *dmaman,
-+ unsigned required_feature_set)
-+{
-+ u32 chans;
-+ int chan = 0;
-+ int feature;
-+
-+ chans = dmaman->chan_available;
-+ for (feature = 0; feature < BCM_DMA_FEATURE_COUNT; feature++)
-+ /* select the subset of available channels with the desired
-+ features */
-+ if (required_feature_set & (1 << feature))
-+ chans &= dmaman->has_feature[feature];
-+
-+ if (!chans)
-+ return -ENOENT;
-+
-+ /* return the ordinal of the first channel in the bitmap */
-+ while (chans != 0 && (chans & 1) == 0) {
-+ chans >>= 1;
-+ chan++;
-+ }
-+ /* claim the channel */
-+ dmaman->chan_available &= ~(1 << chan);
-+
-+ return chan;
-+}
-+
-+static int vc_dmaman_chan_free(struct vc_dmaman *dmaman, int chan)
-+{
-+ if (chan < 0)
-+ return -EINVAL;
-+
-+ if ((1 << chan) & dmaman->chan_available)
-+ return -EIDRM;
-+
-+ dmaman->chan_available |= (1 << chan);
-+
-+ return 0;
-+}
-+
-+/* DMA Manager Monitor */
-+
-+extern int bcm_dma_chan_alloc(unsigned required_feature_set,
-+ void __iomem **out_dma_base, int *out_dma_irq)
-+{
-+ struct vc_dmaman *dmaman = g_dmaman;
-+ struct platform_device *pdev = to_platform_device(dmaman_dev);
-+ struct resource *r;
-+ int chan;
-+
-+ if (!dmaman_dev)
-+ return -ENODEV;
-+
-+ mutex_lock(&dmaman->lock);
-+ chan = vc_dmaman_chan_alloc(dmaman, required_feature_set);
-+ if (chan < 0)
-+ goto out;
-+
-+ r = platform_get_resource(pdev, IORESOURCE_IRQ, (unsigned int)chan);
-+ if (!r) {
-+ dev_err(dmaman_dev, "failed to get irq for DMA channel %d\n",
-+ chan);
-+ vc_dmaman_chan_free(dmaman, chan);
-+ chan = -ENOENT;
-+ goto out;
-+ }
-+
-+ *out_dma_base = BCM2708_DMA_CHANIO(dmaman->dma_base, chan);
-+ *out_dma_irq = r->start;
-+ dev_dbg(dmaman_dev,
-+ "Legacy API allocated channel=%d, base=%p, irq=%i\n",
-+ chan, *out_dma_base, *out_dma_irq);
-+
-+out:
-+ mutex_unlock(&dmaman->lock);
-+
-+ return chan;
-+}
-+EXPORT_SYMBOL_GPL(bcm_dma_chan_alloc);
-+
-+extern int bcm_dma_chan_free(int channel)
-+{
-+ struct vc_dmaman *dmaman = g_dmaman;
-+ int rc;
-+
-+ if (!dmaman_dev)
-+ return -ENODEV;
-+
-+ mutex_lock(&dmaman->lock);
-+ rc = vc_dmaman_chan_free(dmaman, channel);
-+ mutex_unlock(&dmaman->lock);
-+
-+ return rc;
-+}
-+EXPORT_SYMBOL_GPL(bcm_dma_chan_free);
-+
-+int bcm_dmaman_probe(struct platform_device *pdev, void __iomem *base,
-+ u32 chans_available)
-+{
-+ struct device *dev = &pdev->dev;
-+ struct vc_dmaman *dmaman;
-+
-+ dmaman = devm_kzalloc(dev, sizeof(*dmaman), GFP_KERNEL);
-+ if (!dmaman)
-+ return -ENOMEM;
-+
-+ mutex_init(&dmaman->lock);
-+ vc_dmaman_init(dmaman, base, chans_available);
-+ g_dmaman = dmaman;
-+ dmaman_dev = dev;
-+
-+ dev_info(dev, "DMA legacy API manager at %p, dmachans=0x%x\n",
-+ base, chans_available);
-+
-+ return 0;
-+}
-+EXPORT_SYMBOL(bcm_dmaman_probe);
-+
-+int bcm_dmaman_remove(struct platform_device *pdev)
-+{
-+ dmaman_dev = NULL;
-+
-+ return 0;
-+}
-+EXPORT_SYMBOL(bcm_dmaman_remove);
-+
-+MODULE_LICENSE("GPL");
---- /dev/null
-+++ b/include/linux/platform_data/dma-bcm2708.h
-@@ -0,0 +1,143 @@
-+/*
-+ * Copyright (C) 2010 Broadcom
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ */
-+
-+#ifndef _PLAT_BCM2708_DMA_H
-+#define _PLAT_BCM2708_DMA_H
-+
-+/* DMA CS Control and Status bits */
-+#define BCM2708_DMA_ACTIVE BIT(0)
-+#define BCM2708_DMA_INT BIT(2)
-+#define BCM2708_DMA_ISPAUSED BIT(4) /* Pause requested or not active */
-+#define BCM2708_DMA_ISHELD BIT(5) /* Is held by DREQ flow control */
-+#define BCM2708_DMA_ERR BIT(8)
-+#define BCM2708_DMA_ABORT BIT(30) /* stop current CB, go to next, WO */
-+#define BCM2708_DMA_RESET BIT(31) /* WO, self clearing */
-+
-+/* DMA control block "info" field bits */
-+#define BCM2708_DMA_INT_EN BIT(0)
-+#define BCM2708_DMA_TDMODE BIT(1)
-+#define BCM2708_DMA_WAIT_RESP BIT(3)
-+#define BCM2708_DMA_D_INC BIT(4)
-+#define BCM2708_DMA_D_WIDTH BIT(5)
-+#define BCM2708_DMA_D_DREQ BIT(6)
-+#define BCM2708_DMA_S_INC BIT(8)
-+#define BCM2708_DMA_S_WIDTH BIT(9)
-+#define BCM2708_DMA_S_DREQ BIT(10)
-+
-+#define BCM2708_DMA_BURST(x) (((x) & 0xf) << 12)
-+#define BCM2708_DMA_PER_MAP(x) ((x) << 16)
-+#define BCM2708_DMA_WAITS(x) (((x) & 0x1f) << 21)
-+
-+#define BCM2708_DMA_DREQ_EMMC 11
-+#define BCM2708_DMA_DREQ_SDHOST 13
-+
-+#define BCM2708_DMA_CS 0x00 /* Control and Status */
-+#define BCM2708_DMA_ADDR 0x04
-+/* the current control block appears in the following registers - read only */
-+#define BCM2708_DMA_INFO 0x08
-+#define BCM2708_DMA_SOURCE_AD 0x0c
-+#define BCM2708_DMA_DEST_AD 0x10
-+#define BCM2708_DMA_NEXTCB 0x1C
-+#define BCM2708_DMA_DEBUG 0x20
-+
-+#define BCM2708_DMA4_CS (BCM2708_DMA_CHAN(4) + BCM2708_DMA_CS)
-+#define BCM2708_DMA4_ADDR (BCM2708_DMA_CHAN(4) + BCM2708_DMA_ADDR)
-+
-+#define BCM2708_DMA_TDMODE_LEN(w, h) ((h) << 16 | (w))
-+
-+/* When listing features we can ask for when allocating DMA channels give
-+ those with higher priority smaller ordinal numbers */
-+#define BCM_DMA_FEATURE_FAST_ORD 0
-+#define BCM_DMA_FEATURE_BULK_ORD 1
-+#define BCM_DMA_FEATURE_NORMAL_ORD 2
-+#define BCM_DMA_FEATURE_LITE_ORD 3
-+#define BCM_DMA_FEATURE_FAST BIT(BCM_DMA_FEATURE_FAST_ORD)
-+#define BCM_DMA_FEATURE_BULK BIT(BCM_DMA_FEATURE_BULK_ORD)
-+#define BCM_DMA_FEATURE_NORMAL BIT(BCM_DMA_FEATURE_NORMAL_ORD)
-+#define BCM_DMA_FEATURE_LITE BIT(BCM_DMA_FEATURE_LITE_ORD)
-+#define BCM_DMA_FEATURE_COUNT 4
-+
-+struct bcm2708_dma_cb {
-+ unsigned long info;
-+ unsigned long src;
-+ unsigned long dst;
-+ unsigned long length;
-+ unsigned long stride;
-+ unsigned long next;
-+ unsigned long pad[2];
-+};
-+
-+struct scatterlist;
-+struct platform_device;
-+
-+#ifdef CONFIG_DMA_BCM2708
-+
-+int bcm_sg_suitable_for_dma(struct scatterlist *sg_ptr, int sg_len);
-+void bcm_dma_start(void __iomem *dma_chan_base, dma_addr_t control_block);
-+void bcm_dma_wait_idle(void __iomem *dma_chan_base);
-+bool bcm_dma_is_busy(void __iomem *dma_chan_base);
-+int bcm_dma_abort(void __iomem *dma_chan_base);
-+
-+/* return channel no or -ve error */
-+int bcm_dma_chan_alloc(unsigned preferred_feature_set,
-+ void __iomem **out_dma_base, int *out_dma_irq);
-+int bcm_dma_chan_free(int channel);
-+
-+int bcm_dmaman_probe(struct platform_device *pdev, void __iomem *base,
-+ u32 chans_available);
-+int bcm_dmaman_remove(struct platform_device *pdev);
-+
-+#else /* CONFIG_DMA_BCM2708 */
-+
-+static inline int bcm_sg_suitable_for_dma(struct scatterlist *sg_ptr,
-+ int sg_len)
-+{
-+ return 0;
-+}
-+
-+static inline void bcm_dma_start(void __iomem *dma_chan_base,
-+ dma_addr_t control_block) { }
-+
-+static inline void bcm_dma_wait_idle(void __iomem *dma_chan_base) { }
-+
-+static inline bool bcm_dma_is_busy(void __iomem *dma_chan_base)
-+{
-+ return false;
-+}
-+
-+static inline int bcm_dma_abort(void __iomem *dma_chan_base)
-+{
-+ return -EINVAL;
-+}
-+
-+static inline int bcm_dma_chan_alloc(unsigned preferred_feature_set,
-+ void __iomem **out_dma_base,
-+ int *out_dma_irq)
-+{
-+ return -EINVAL;
-+}
-+
-+static inline int bcm_dma_chan_free(int channel)
-+{
-+ return -EINVAL;
-+}
-+
-+static inline int bcm_dmaman_probe(struct platform_device *pdev,
-+ void __iomem *base, u32 chans_available)
-+{
-+ return 0;
-+}
-+
-+static inline int bcm_dmaman_remove(struct platform_device *pdev)
-+{
-+ return 0;
-+}
-+
-+#endif /* CONFIG_DMA_BCM2708 */
-+
-+#endif /* _PLAT_BCM2708_DMA_H */
diff --git a/target/linux/brcm2708/patches-4.4/0032-MMC-added-alternative-MMC-driver.patch b/target/linux/brcm2708/patches-4.4/0032-MMC-added-alternative-MMC-driver.patch
deleted file mode 100644
index a37a64a..0000000
--- a/target/linux/brcm2708/patches-4.4/0032-MMC-added-alternative-MMC-driver.patch
+++ /dev/null
@@ -1,1691 +0,0 @@
-From 5646c03db7e90b2eff7cec1679877ed2789ba3c9 Mon Sep 17 00:00:00 2001
-From: gellert <gellert at raspberrypi.org>
-Date: Fri, 15 Aug 2014 16:35:06 +0100
-Subject: [PATCH] MMC: added alternative MMC driver
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-mmc: Disable CMD23 transfers on all cards
-
-Pending wire-level investigation of these types of transfers
-and associated errors on bcm2835-mmc, disable for now. Fallback of
-CMD18/CMD25 transfers will be used automatically by the MMC layer.
-
-Reported/Tested-by: Gellert Weisz <gellert at raspberrypi.org>
-
-mmc: bcm2835-mmc: enable DT support for all architectures
-
-Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
-Enable Device Tree support for all architectures.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-mmc: bcm2835-mmc: fix probe error handling
-
-Probe error handling is broken in several places.
-Simplify error handling by using device managed functions.
-Replace pr_{err,info} with dev_{err,info}.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-bcm2835-mmc: Add locks when accessing sdhost registers
-
-bcm2835-mmc: Add range of debug options for slowing things down
-
-bcm2835-mmc: Add option to disable some delays
-
-bcm2835-mmc: Add option to disable MMC_QUIRK_BLK_NO_CMD23
-
-bcm2835-mmc: Default to disabling MMC_QUIRK_BLK_NO_CMD23
-
-bcm2835-mmc: Adding overclocking option
-
-Allow a different clock speed to be substitued for a requested 50MHz.
-This option is exposed using the "overclock_50" DT parameter.
-Note that the mmc interface is restricted to EVEN integer divisions of
-250MHz, and the highest sensible option is 63 (250/4 = 62.5), the
-next being 125 (250/2) which is much too high.
-
-Use at your own risk.
-
-bcm2835-mmc: Round up the overclock, so 62 works for 62.5Mhz
-
-Also only warn once for each overclock setting.
-
-mmc: bcm2835-mmc: Make available on ARCH_BCM2835
-
-Make the bcm2835-mmc driver available for use on ARCH_BCM2835.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-BCM270x_DT: add bcm2835-mmc entry
-
-Add Device Tree entry for bcm2835-mmc.
-In non-DT mode, don't add the device in the board file.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-bcm2835-mmc: Don't overwrite MMC capabilities from DT
----
- drivers/mmc/core/quirks.c | 6 +
- drivers/mmc/host/Kconfig | 29 +
- drivers/mmc/host/Makefile | 1 +
- drivers/mmc/host/bcm2835-mmc.c | 1542 ++++++++++++++++++++++++++++++++++++++++
- 4 files changed, 1578 insertions(+)
- create mode 100644 drivers/mmc/host/bcm2835-mmc.c
-
---- a/drivers/mmc/core/quirks.c
-+++ b/drivers/mmc/core/quirks.c
-@@ -53,6 +53,7 @@ static const struct mmc_fixup mmc_fixup_
-
- void mmc_fixup_device(struct mmc_card *card, const struct mmc_fixup *table)
- {
-+ extern unsigned mmc_debug;
- const struct mmc_fixup *f;
- u64 rev = cid_rev_card(card);
-
-@@ -77,5 +78,10 @@ void mmc_fixup_device(struct mmc_card *c
- f->vendor_fixup(card, f->data);
- }
- }
-+ /* SDHCI on BCM2708 - bug causes a certain sequence of CMD23 operations to fail.
-+ * Disable this flag for all cards (fall-back to CMD25/CMD18 multi-block transfers).
-+ */
-+ if (mmc_debug & (1<<13))
-+ card->quirks |= MMC_QUIRK_BLK_NO_CMD23;
- }
- EXPORT_SYMBOL(mmc_fixup_device);
---- a/drivers/mmc/host/Kconfig
-+++ b/drivers/mmc/host/Kconfig
-@@ -4,6 +4,35 @@
-
- comment "MMC/SD/SDIO Host Controller Drivers"
-
-+config MMC_BCM2835
-+ tristate "MMC support on BCM2835"
-+ depends on MACH_BCM2708 || MACH_BCM2709 || ARCH_BCM2835
-+ help
-+ This selects the MMC Interface on BCM2835.
-+
-+ If you have a controller with this interface, say Y or M here.
-+
-+ If unsure, say N.
-+
-+config MMC_BCM2835_DMA
-+ bool "DMA support on BCM2835 Arasan controller"
-+ depends on MMC_BCM2835
-+ help
-+ Enable DMA support on the Arasan SDHCI controller in Broadcom 2708
-+ based chips.
-+
-+ If unsure, say N.
-+
-+config MMC_BCM2835_PIO_DMA_BARRIER
-+ int "Block count limit for PIO transfers"
-+ depends on MMC_BCM2835 && MMC_BCM2835_DMA
-+ range 0 256
-+ default 2
-+ help
-+ The inclusive limit in bytes under which PIO will be used instead of DMA
-+
-+ If unsure, say 2 here.
-+
- config MMC_ARMMMCI
- tristate "ARM AMBA Multimedia Card Interface support"
- depends on ARM_AMBA
---- a/drivers/mmc/host/Makefile
-+++ b/drivers/mmc/host/Makefile
-@@ -18,6 +18,7 @@ obj-$(CONFIG_MMC_SDHCI_S3C) += sdhci-s3c
- obj-$(CONFIG_MMC_SDHCI_SIRF) += sdhci-sirf.o
- obj-$(CONFIG_MMC_SDHCI_F_SDH30) += sdhci_f_sdh30.o
- obj-$(CONFIG_MMC_SDHCI_SPEAR) += sdhci-spear.o
-+obj-$(CONFIG_MMC_BCM2835) += bcm2835-mmc.o
- obj-$(CONFIG_MMC_WBSD) += wbsd.o
- obj-$(CONFIG_MMC_AU1X) += au1xmmc.o
- obj-$(CONFIG_MMC_MTK) += mtk-sd.o
---- /dev/null
-+++ b/drivers/mmc/host/bcm2835-mmc.c
-@@ -0,0 +1,1542 @@
-+/*
-+ * BCM2835 MMC host driver.
-+ *
-+ * Author: Gellert Weisz <gellert at raspberrypi.org>
-+ * Copyright 2014
-+ *
-+ * Based on
-+ * sdhci-bcm2708.c by Broadcom
-+ * sdhci-bcm2835.c by Stephen Warren and Oleksandr Tymoshenko
-+ * sdhci.c and sdhci-pci.c by Pierre Ossman
-+ *
-+ * This program is free software; you can redistribute it and/or modify it
-+ * under the terms and conditions of the GNU General Public License,
-+ * version 2, as published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope it will be useful, but WITHOUT
-+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
-+ * more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
-+ */
-+
-+#include <linux/delay.h>
-+#include <linux/module.h>
-+#include <linux/io.h>
-+#include <linux/mmc/mmc.h>
-+#include <linux/mmc/host.h>
-+#include <linux/mmc/sd.h>
-+#include <linux/scatterlist.h>
-+#include <linux/of_address.h>
-+#include <linux/of_irq.h>
-+#include <linux/clk.h>
-+#include <linux/platform_device.h>
-+#include <linux/err.h>
-+#include <linux/blkdev.h>
-+#include <linux/dmaengine.h>
-+#include <linux/dma-mapping.h>
-+#include <linux/of_dma.h>
-+
-+#include "sdhci.h"
-+
-+
-+#define DRIVER_NAME "mmc-bcm2835"
-+
-+#define DBG(f, x...) \
-+pr_debug(DRIVER_NAME " [%s()]: " f, __func__, ## x)
-+
-+#ifndef CONFIG_MMC_BCM2835_DMA
-+ #define FORCE_PIO
-+#endif
-+
-+
-+/* the inclusive limit in bytes under which PIO will be used instead of DMA */
-+#ifdef CONFIG_MMC_BCM2835_PIO_DMA_BARRIER
-+#define PIO_DMA_BARRIER CONFIG_MMC_BCM2835_PIO_DMA_BARRIER
-+#else
-+#define PIO_DMA_BARRIER 00
-+#endif
-+
-+#define MIN_FREQ 400000
-+#define TIMEOUT_VAL 0xE
-+#define BCM2835_SDHCI_WRITE_DELAY(f) (((2 * 1000000) / f) + 1)
-+
-+
-+unsigned mmc_debug;
-+unsigned mmc_debug2;
-+
-+struct bcm2835_host {
-+ spinlock_t lock;
-+
-+ void __iomem *ioaddr;
-+ u32 bus_addr;
-+
-+ struct mmc_host *mmc;
-+
-+ u32 timeout;
-+
-+ int clock; /* Current clock speed */
-+ u8 pwr; /* Current voltage */
-+
-+ unsigned int max_clk; /* Max possible freq */
-+ unsigned int timeout_clk; /* Timeout freq (KHz) */
-+ unsigned int clk_mul; /* Clock Muliplier value */
-+
-+ struct tasklet_struct finish_tasklet; /* Tasklet structures */
-+
-+ struct timer_list timer; /* Timer for timeouts */
-+
-+ struct sg_mapping_iter sg_miter; /* SG state for PIO */
-+ unsigned int blocks; /* remaining PIO blocks */
-+
-+ int irq; /* Device IRQ */
-+
-+
-+ u32 ier; /* cached registers */
-+
-+ struct mmc_request *mrq; /* Current request */
-+ struct mmc_command *cmd; /* Current command */
-+ struct mmc_data *data; /* Current data request */
-+ unsigned int data_early:1; /* Data finished before cmd */
-+
-+ wait_queue_head_t buf_ready_int; /* Waitqueue for Buffer Read Ready interrupt */
-+
-+ u32 thread_isr;
-+
-+ u32 shadow;
-+
-+ /*DMA part*/
-+ struct dma_chan *dma_chan_rx; /* DMA channel for reads */
-+ struct dma_chan *dma_chan_tx; /* DMA channel for writes */
-+ struct dma_async_tx_descriptor *tx_desc; /* descriptor */
-+
-+ bool have_dma;
-+ bool use_dma;
-+ /*end of DMA part*/
-+
-+ int max_delay; /* maximum length of time spent waiting */
-+
-+ int flags; /* Host attributes */
-+#define SDHCI_REQ_USE_DMA (1<<2) /* Use DMA for this req. */
-+#define SDHCI_DEVICE_DEAD (1<<3) /* Device unresponsive */
-+#define SDHCI_AUTO_CMD12 (1<<6) /* Auto CMD12 support */
-+#define SDHCI_AUTO_CMD23 (1<<7) /* Auto CMD23 support */
-+#define SDHCI_SDIO_IRQ_ENABLED (1<<9) /* SDIO irq enabled */
-+
-+ u32 overclock_50; /* frequency to use when 50MHz is requested (in MHz) */
-+ u32 max_overclock; /* Highest reported */
-+};
-+
-+
-+static inline void bcm2835_mmc_writel(struct bcm2835_host *host, u32 val, int reg, int from)
-+{
-+ unsigned delay;
-+ lockdep_assert_held_once(&host->lock);
-+ writel(val, host->ioaddr + reg);
-+ udelay(BCM2835_SDHCI_WRITE_DELAY(max(host->clock, MIN_FREQ)));
-+
-+ delay = ((mmc_debug >> 16) & 0xf) << ((mmc_debug >> 20) & 0xf);
-+ if (delay && !((1<<from) & mmc_debug2))
-+ udelay(delay);
-+}
-+
-+static inline void mmc_raw_writel(struct bcm2835_host *host, u32 val, int reg)
-+{
-+ unsigned delay;
-+ lockdep_assert_held_once(&host->lock);
-+ writel(val, host->ioaddr + reg);
-+
-+ delay = ((mmc_debug >> 24) & 0xf) << ((mmc_debug >> 28) & 0xf);
-+ if (delay)
-+ udelay(delay);
-+}
-+
-+static inline u32 bcm2835_mmc_readl(struct bcm2835_host *host, int reg)
-+{
-+ lockdep_assert_held_once(&host->lock);
-+ return readl(host->ioaddr + reg);
-+}
-+
-+static inline void bcm2835_mmc_writew(struct bcm2835_host *host, u16 val, int reg)
-+{
-+ u32 oldval = (reg == SDHCI_COMMAND) ? host->shadow :
-+ bcm2835_mmc_readl(host, reg & ~3);
-+ u32 word_num = (reg >> 1) & 1;
-+ u32 word_shift = word_num * 16;
-+ u32 mask = 0xffff << word_shift;
-+ u32 newval = (oldval & ~mask) | (val << word_shift);
-+
-+ if (reg == SDHCI_TRANSFER_MODE)
-+ host->shadow = newval;
-+ else
-+ bcm2835_mmc_writel(host, newval, reg & ~3, 0);
-+
-+}
-+
-+static inline void bcm2835_mmc_writeb(struct bcm2835_host *host, u8 val, int reg)
-+{
-+ u32 oldval = bcm2835_mmc_readl(host, reg & ~3);
-+ u32 byte_num = reg & 3;
-+ u32 byte_shift = byte_num * 8;
-+ u32 mask = 0xff << byte_shift;
-+ u32 newval = (oldval & ~mask) | (val << byte_shift);
-+
-+ bcm2835_mmc_writel(host, newval, reg & ~3, 1);
-+}
-+
-+
-+static inline u16 bcm2835_mmc_readw(struct bcm2835_host *host, int reg)
-+{
-+ u32 val = bcm2835_mmc_readl(host, (reg & ~3));
-+ u32 word_num = (reg >> 1) & 1;
-+ u32 word_shift = word_num * 16;
-+ u32 word = (val >> word_shift) & 0xffff;
-+
-+ return word;
-+}
-+
-+static inline u8 bcm2835_mmc_readb(struct bcm2835_host *host, int reg)
-+{
-+ u32 val = bcm2835_mmc_readl(host, (reg & ~3));
-+ u32 byte_num = reg & 3;
-+ u32 byte_shift = byte_num * 8;
-+ u32 byte = (val >> byte_shift) & 0xff;
-+
-+ return byte;
-+}
-+
-+static void bcm2835_mmc_unsignal_irqs(struct bcm2835_host *host, u32 clear)
-+{
-+ u32 ier;
-+
-+ ier = bcm2835_mmc_readl(host, SDHCI_SIGNAL_ENABLE);
-+ ier &= ~clear;
-+ /* change which requests generate IRQs - makes no difference to
-+ the content of SDHCI_INT_STATUS, or the need to acknowledge IRQs */
-+ bcm2835_mmc_writel(host, ier, SDHCI_SIGNAL_ENABLE, 2);
-+}
-+
-+
-+static void bcm2835_mmc_dumpregs(struct bcm2835_host *host)
-+{
-+ pr_debug(DRIVER_NAME ": =========== REGISTER DUMP (%s)===========\n",
-+ mmc_hostname(host->mmc));
-+
-+ pr_debug(DRIVER_NAME ": Sys addr: 0x%08x | Version: 0x%08x\n",
-+ bcm2835_mmc_readl(host, SDHCI_DMA_ADDRESS),
-+ bcm2835_mmc_readw(host, SDHCI_HOST_VERSION));
-+ pr_debug(DRIVER_NAME ": Blk size: 0x%08x | Blk cnt: 0x%08x\n",
-+ bcm2835_mmc_readw(host, SDHCI_BLOCK_SIZE),
-+ bcm2835_mmc_readw(host, SDHCI_BLOCK_COUNT));
-+ pr_debug(DRIVER_NAME ": Argument: 0x%08x | Trn mode: 0x%08x\n",
-+ bcm2835_mmc_readl(host, SDHCI_ARGUMENT),
-+ bcm2835_mmc_readw(host, SDHCI_TRANSFER_MODE));
-+ pr_debug(DRIVER_NAME ": Present: 0x%08x | Host ctl: 0x%08x\n",
-+ bcm2835_mmc_readl(host, SDHCI_PRESENT_STATE),
-+ bcm2835_mmc_readb(host, SDHCI_HOST_CONTROL));
-+ pr_debug(DRIVER_NAME ": Power: 0x%08x | Blk gap: 0x%08x\n",
-+ bcm2835_mmc_readb(host, SDHCI_POWER_CONTROL),
-+ bcm2835_mmc_readb(host, SDHCI_BLOCK_GAP_CONTROL));
-+ pr_debug(DRIVER_NAME ": Wake-up: 0x%08x | Clock: 0x%08x\n",
-+ bcm2835_mmc_readb(host, SDHCI_WAKE_UP_CONTROL),
-+ bcm2835_mmc_readw(host, SDHCI_CLOCK_CONTROL));
-+ pr_debug(DRIVER_NAME ": Timeout: 0x%08x | Int stat: 0x%08x\n",
-+ bcm2835_mmc_readb(host, SDHCI_TIMEOUT_CONTROL),
-+ bcm2835_mmc_readl(host, SDHCI_INT_STATUS));
-+ pr_debug(DRIVER_NAME ": Int enab: 0x%08x | Sig enab: 0x%08x\n",
-+ bcm2835_mmc_readl(host, SDHCI_INT_ENABLE),
-+ bcm2835_mmc_readl(host, SDHCI_SIGNAL_ENABLE));
-+ pr_debug(DRIVER_NAME ": AC12 err: 0x%08x | Slot int: 0x%08x\n",
-+ bcm2835_mmc_readw(host, SDHCI_ACMD12_ERR),
-+ bcm2835_mmc_readw(host, SDHCI_SLOT_INT_STATUS));
-+ pr_debug(DRIVER_NAME ": Caps: 0x%08x | Caps_1: 0x%08x\n",
-+ bcm2835_mmc_readl(host, SDHCI_CAPABILITIES),
-+ bcm2835_mmc_readl(host, SDHCI_CAPABILITIES_1));
-+ pr_debug(DRIVER_NAME ": Cmd: 0x%08x | Max curr: 0x%08x\n",
-+ bcm2835_mmc_readw(host, SDHCI_COMMAND),
-+ bcm2835_mmc_readl(host, SDHCI_MAX_CURRENT));
-+ pr_debug(DRIVER_NAME ": Host ctl2: 0x%08x\n",
-+ bcm2835_mmc_readw(host, SDHCI_HOST_CONTROL2));
-+
-+ pr_debug(DRIVER_NAME ": ===========================================\n");
-+}
-+
-+
-+static void bcm2835_mmc_reset(struct bcm2835_host *host, u8 mask)
-+{
-+ unsigned long timeout;
-+ unsigned long flags;
-+
-+ spin_lock_irqsave(&host->lock, flags);
-+ bcm2835_mmc_writeb(host, mask, SDHCI_SOFTWARE_RESET);
-+
-+ if (mask & SDHCI_RESET_ALL)
-+ host->clock = 0;
-+
-+ /* Wait max 100 ms */
-+ timeout = 100;
-+
-+ /* hw clears the bit when it's done */
-+ while (bcm2835_mmc_readb(host, SDHCI_SOFTWARE_RESET) & mask) {
-+ if (timeout == 0) {
-+ pr_err("%s: Reset 0x%x never completed.\n",
-+ mmc_hostname(host->mmc), (int)mask);
-+ bcm2835_mmc_dumpregs(host);
-+ return;
-+ }
-+ timeout--;
-+ spin_unlock_irqrestore(&host->lock, flags);
-+ mdelay(1);
-+ spin_lock_irqsave(&host->lock, flags);
-+ }
-+
-+ if (100-timeout > 10 && 100-timeout > host->max_delay) {
-+ host->max_delay = 100-timeout;
-+ pr_warning("Warning: MMC controller hung for %d ms\n", host->max_delay);
-+ }
-+ spin_unlock_irqrestore(&host->lock, flags);
-+}
-+
-+static void bcm2835_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios);
-+
-+static void bcm2835_mmc_init(struct bcm2835_host *host, int soft)
-+{
-+ unsigned long flags;
-+ if (soft)
-+ bcm2835_mmc_reset(host, SDHCI_RESET_CMD|SDHCI_RESET_DATA);
-+ else
-+ bcm2835_mmc_reset(host, SDHCI_RESET_ALL);
-+
-+ host->ier = SDHCI_INT_BUS_POWER | SDHCI_INT_DATA_END_BIT |
-+ SDHCI_INT_DATA_CRC | SDHCI_INT_DATA_TIMEOUT |
-+ SDHCI_INT_INDEX | SDHCI_INT_END_BIT | SDHCI_INT_CRC |
-+ SDHCI_INT_TIMEOUT | SDHCI_INT_DATA_END |
-+ SDHCI_INT_RESPONSE;
-+
-+ spin_lock_irqsave(&host->lock, flags);
-+ bcm2835_mmc_writel(host, host->ier, SDHCI_INT_ENABLE, 3);
-+ bcm2835_mmc_writel(host, host->ier, SDHCI_SIGNAL_ENABLE, 3);
-+ spin_unlock_irqrestore(&host->lock, flags);
-+
-+ if (soft) {
-+ /* force clock reconfiguration */
-+ host->clock = 0;
-+ bcm2835_mmc_set_ios(host->mmc, &host->mmc->ios);
-+ }
-+}
-+
-+
-+
-+static void bcm2835_mmc_finish_data(struct bcm2835_host *host);
-+
-+static void bcm2835_mmc_dma_complete(void *param)
-+{
-+ struct bcm2835_host *host = param;
-+ struct dma_chan *dma_chan;
-+ unsigned long flags;
-+ u32 dir_data;
-+
-+ spin_lock_irqsave(&host->lock, flags);
-+
-+ if (host->data && !(host->data->flags & MMC_DATA_WRITE)) {
-+ /* otherwise handled in SDHCI IRQ */
-+ dma_chan = host->dma_chan_rx;
-+ dir_data = DMA_FROM_DEVICE;
-+
-+ dma_unmap_sg(dma_chan->device->dev,
-+ host->data->sg, host->data->sg_len,
-+ dir_data);
-+
-+ bcm2835_mmc_finish_data(host);
-+ }
-+
-+ spin_unlock_irqrestore(&host->lock, flags);
-+}
-+
-+static void bcm2835_bcm2835_mmc_read_block_pio(struct bcm2835_host *host)
-+{
-+ unsigned long flags;
-+ size_t blksize, len, chunk;
-+
-+ u32 uninitialized_var(scratch);
-+ u8 *buf;
-+
-+ blksize = host->data->blksz;
-+ chunk = 0;
-+
-+ local_irq_save(flags);
-+
-+ while (blksize) {
-+ if (!sg_miter_next(&host->sg_miter))
-+ BUG();
-+
-+ len = min(host->sg_miter.length, blksize);
-+
-+ blksize -= len;
-+ host->sg_miter.consumed = len;
-+
-+ buf = host->sg_miter.addr;
-+
-+ while (len) {
-+ if (chunk == 0) {
-+ scratch = bcm2835_mmc_readl(host, SDHCI_BUFFER);
-+ chunk = 4;
-+ }
-+
-+ *buf = scratch & 0xFF;
-+
-+ buf++;
-+ scratch >>= 8;
-+ chunk--;
-+ len--;
-+ }
-+ }
-+
-+ sg_miter_stop(&host->sg_miter);
-+
-+ local_irq_restore(flags);
-+}
-+
-+static void bcm2835_bcm2835_mmc_write_block_pio(struct bcm2835_host *host)
-+{
-+ unsigned long flags;
-+ size_t blksize, len, chunk;
-+ u32 scratch;
-+ u8 *buf;
-+
-+ blksize = host->data->blksz;
-+ chunk = 0;
-+ chunk = 0;
-+ scratch = 0;
-+
-+ local_irq_save(flags);
-+
-+ while (blksize) {
-+ if (!sg_miter_next(&host->sg_miter))
-+ BUG();
-+
-+ len = min(host->sg_miter.length, blksize);
-+
-+ blksize -= len;
-+ host->sg_miter.consumed = len;
-+
-+ buf = host->sg_miter.addr;
-+
-+ while (len) {
-+ scratch |= (u32)*buf << (chunk * 8);
-+
-+ buf++;
-+ chunk++;
-+ len--;
-+
-+ if ((chunk == 4) || ((len == 0) && (blksize == 0))) {
-+ mmc_raw_writel(host, scratch, SDHCI_BUFFER);
-+ chunk = 0;
-+ scratch = 0;
-+ }
-+ }
-+ }
-+
-+ sg_miter_stop(&host->sg_miter);
-+
-+ local_irq_restore(flags);
-+}
-+
-+
-+static void bcm2835_mmc_transfer_pio(struct bcm2835_host *host)
-+{
-+ u32 mask;
-+
-+ BUG_ON(!host->data);
-+
-+ if (host->blocks == 0)
-+ return;
-+
-+ if (host->data->flags & MMC_DATA_READ)
-+ mask = SDHCI_DATA_AVAILABLE;
-+ else
-+ mask = SDHCI_SPACE_AVAILABLE;
-+
-+ while (bcm2835_mmc_readl(host, SDHCI_PRESENT_STATE) & mask) {
-+
-+ if (host->data->flags & MMC_DATA_READ)
-+ bcm2835_bcm2835_mmc_read_block_pio(host);
-+ else
-+ bcm2835_bcm2835_mmc_write_block_pio(host);
-+
-+ host->blocks--;
-+
-+ /* QUIRK used in sdhci.c removes the 'if' */
-+ /* but it seems this is unnecessary */
-+ if (host->blocks == 0)
-+ break;
-+
-+
-+ }
-+}
-+
-+
-+static void bcm2835_mmc_transfer_dma(struct bcm2835_host *host)
-+{
-+ u32 len, dir_data, dir_slave;
-+ struct dma_async_tx_descriptor *desc = NULL;
-+ struct dma_chan *dma_chan;
-+
-+
-+ WARN_ON(!host->data);
-+
-+ if (!host->data)
-+ return;
-+
-+ if (host->blocks == 0)
-+ return;
-+
-+ if (host->data->flags & MMC_DATA_READ) {
-+ dma_chan = host->dma_chan_rx;
-+ dir_data = DMA_FROM_DEVICE;
-+ dir_slave = DMA_DEV_TO_MEM;
-+ } else {
-+ dma_chan = host->dma_chan_tx;
-+ dir_data = DMA_TO_DEVICE;
-+ dir_slave = DMA_MEM_TO_DEV;
-+ }
-+
-+ BUG_ON(!dma_chan->device);
-+ BUG_ON(!dma_chan->device->dev);
-+ BUG_ON(!host->data->sg);
-+
-+ len = dma_map_sg(dma_chan->device->dev, host->data->sg,
-+ host->data->sg_len, dir_data);
-+ if (len > 0) {
-+ desc = dmaengine_prep_slave_sg(dma_chan, host->data->sg,
-+ len, dir_slave,
-+ DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
-+ } else {
-+ dev_err(mmc_dev(host->mmc), "dma_map_sg returned zero length\n");
-+ }
-+ if (desc) {
-+ unsigned long flags;
-+ spin_lock_irqsave(&host->lock, flags);
-+ bcm2835_mmc_unsignal_irqs(host, SDHCI_INT_DATA_AVAIL |
-+ SDHCI_INT_SPACE_AVAIL);
-+ host->tx_desc = desc;
-+ desc->callback = bcm2835_mmc_dma_complete;
-+ desc->callback_param = host;
-+ spin_unlock_irqrestore(&host->lock, flags);
-+ dmaengine_submit(desc);
-+ dma_async_issue_pending(dma_chan);
-+ }
-+
-+}
-+
-+
-+
-+static void bcm2835_mmc_set_transfer_irqs(struct bcm2835_host *host)
-+{
-+ u32 pio_irqs = SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL;
-+ u32 dma_irqs = SDHCI_INT_DMA_END | SDHCI_INT_ADMA_ERROR;
-+
-+ if (host->use_dma)
-+ host->ier = (host->ier & ~pio_irqs) | dma_irqs;
-+ else
-+ host->ier = (host->ier & ~dma_irqs) | pio_irqs;
-+
-+ bcm2835_mmc_writel(host, host->ier, SDHCI_INT_ENABLE, 4);
-+ bcm2835_mmc_writel(host, host->ier, SDHCI_SIGNAL_ENABLE, 4);
-+}
-+
-+
-+static void bcm2835_mmc_prepare_data(struct bcm2835_host *host, struct mmc_command *cmd)
-+{
-+ u8 count;
-+ struct mmc_data *data = cmd->data;
-+
-+ WARN_ON(host->data);
-+
-+ if (data || (cmd->flags & MMC_RSP_BUSY)) {
-+ count = TIMEOUT_VAL;
-+ bcm2835_mmc_writeb(host, count, SDHCI_TIMEOUT_CONTROL);
-+ }
-+
-+ if (!data)
-+ return;
-+
-+ /* Sanity checks */
-+ BUG_ON(data->blksz * data->blocks > 524288);
-+ BUG_ON(data->blksz > host->mmc->max_blk_size);
-+ BUG_ON(data->blocks > 65535);
-+
-+ host->data = data;
-+ host->data_early = 0;
-+ host->data->bytes_xfered = 0;
-+
-+
-+ if (!(host->flags & SDHCI_REQ_USE_DMA)) {
-+ int flags;
-+
-+ flags = SG_MITER_ATOMIC;
-+ if (host->data->flags & MMC_DATA_READ)
-+ flags |= SG_MITER_TO_SG;
-+ else
-+ flags |= SG_MITER_FROM_SG;
-+ sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags);
-+ host->blocks = data->blocks;
-+ }
-+
-+ host->use_dma = host->have_dma && data->blocks > PIO_DMA_BARRIER;
-+
-+ bcm2835_mmc_set_transfer_irqs(host);
-+
-+ /* Set the DMA boundary value and block size */
-+ bcm2835_mmc_writew(host, SDHCI_MAKE_BLKSZ(SDHCI_DEFAULT_BOUNDARY_ARG,
-+ data->blksz), SDHCI_BLOCK_SIZE);
-+ bcm2835_mmc_writew(host, data->blocks, SDHCI_BLOCK_COUNT);
-+
-+ BUG_ON(!host->data);
-+}
-+
-+static void bcm2835_mmc_set_transfer_mode(struct bcm2835_host *host,
-+ struct mmc_command *cmd)
-+{
-+ u16 mode;
-+ struct mmc_data *data = cmd->data;
-+
-+ if (data == NULL) {
-+ /* clear Auto CMD settings for no data CMDs */
-+ mode = bcm2835_mmc_readw(host, SDHCI_TRANSFER_MODE);
-+ bcm2835_mmc_writew(host, mode & ~(SDHCI_TRNS_AUTO_CMD12 |
-+ SDHCI_TRNS_AUTO_CMD23), SDHCI_TRANSFER_MODE);
-+ return;
-+ }
-+
-+ WARN_ON(!host->data);
-+
-+ mode = SDHCI_TRNS_BLK_CNT_EN;
-+
-+ if ((mmc_op_multi(cmd->opcode) || data->blocks > 1)) {
-+ mode |= SDHCI_TRNS_MULTI;
-+
-+ /*
-+ * If we are sending CMD23, CMD12 never gets sent
-+ * on successful completion (so no Auto-CMD12).
-+ */
-+ if (!host->mrq->sbc && (host->flags & SDHCI_AUTO_CMD12))
-+ mode |= SDHCI_TRNS_AUTO_CMD12;
-+ else if (host->mrq->sbc && (host->flags & SDHCI_AUTO_CMD23)) {
-+ mode |= SDHCI_TRNS_AUTO_CMD23;
-+ bcm2835_mmc_writel(host, host->mrq->sbc->arg, SDHCI_ARGUMENT2, 5);
-+ }
-+ }
-+
-+ if (data->flags & MMC_DATA_READ)
-+ mode |= SDHCI_TRNS_READ;
-+ if (host->flags & SDHCI_REQ_USE_DMA)
-+ mode |= SDHCI_TRNS_DMA;
-+
-+ bcm2835_mmc_writew(host, mode, SDHCI_TRANSFER_MODE);
-+}
-+
-+void bcm2835_mmc_send_command(struct bcm2835_host *host, struct mmc_command *cmd)
-+{
-+ int flags;
-+ u32 mask;
-+ unsigned long timeout;
-+
-+ WARN_ON(host->cmd);
-+
-+ /* Wait max 10 ms */
-+ timeout = 1000;
-+
-+ mask = SDHCI_CMD_INHIBIT;
-+ if ((cmd->data != NULL) || (cmd->flags & MMC_RSP_BUSY))
-+ mask |= SDHCI_DATA_INHIBIT;
-+
-+ /* We shouldn't wait for data inihibit for stop commands, even
-+ though they might use busy signaling */
-+ if (host->mrq->data && (cmd == host->mrq->data->stop))
-+ mask &= ~SDHCI_DATA_INHIBIT;
-+
-+ while (bcm2835_mmc_readl(host, SDHCI_PRESENT_STATE) & mask) {
-+ if (timeout == 0) {
-+ pr_err("%s: Controller never released inhibit bit(s).\n",
-+ mmc_hostname(host->mmc));
-+ bcm2835_mmc_dumpregs(host);
-+ cmd->error = -EIO;
-+ tasklet_schedule(&host->finish_tasklet);
-+ return;
-+ }
-+ timeout--;
-+ udelay(10);
-+ }
-+
-+ if ((1000-timeout)/100 > 1 && (1000-timeout)/100 > host->max_delay) {
-+ host->max_delay = (1000-timeout)/100;
-+ pr_warning("Warning: MMC controller hung for %d ms\n", host->max_delay);
-+ }
-+
-+ timeout = jiffies;
-+ if (!cmd->data && cmd->busy_timeout > 9000)
-+ timeout += DIV_ROUND_UP(cmd->busy_timeout, 1000) * HZ + HZ;
-+ else
-+ timeout += 10 * HZ;
-+ mod_timer(&host->timer, timeout);
-+
-+ host->cmd = cmd;
-+
-+ bcm2835_mmc_prepare_data(host, cmd);
-+
-+ bcm2835_mmc_writel(host, cmd->arg, SDHCI_ARGUMENT, 6);
-+
-+ bcm2835_mmc_set_transfer_mode(host, cmd);
-+
-+ if ((cmd->flags & MMC_RSP_136) && (cmd->flags & MMC_RSP_BUSY)) {
-+ pr_err("%s: Unsupported response type!\n",
-+ mmc_hostname(host->mmc));
-+ cmd->error = -EINVAL;
-+ tasklet_schedule(&host->finish_tasklet);
-+ return;
-+ }
-+
-+ if (!(cmd->flags & MMC_RSP_PRESENT))
-+ flags = SDHCI_CMD_RESP_NONE;
-+ else if (cmd->flags & MMC_RSP_136)
-+ flags = SDHCI_CMD_RESP_LONG;
-+ else if (cmd->flags & MMC_RSP_BUSY)
-+ flags = SDHCI_CMD_RESP_SHORT_BUSY;
-+ else
-+ flags = SDHCI_CMD_RESP_SHORT;
-+
-+ if (cmd->flags & MMC_RSP_CRC)
-+ flags |= SDHCI_CMD_CRC;
-+ if (cmd->flags & MMC_RSP_OPCODE)
-+ flags |= SDHCI_CMD_INDEX;
-+
-+ if (cmd->data)
-+ flags |= SDHCI_CMD_DATA;
-+
-+ bcm2835_mmc_writew(host, SDHCI_MAKE_CMD(cmd->opcode, flags), SDHCI_COMMAND);
-+}
-+
-+
-+static void bcm2835_mmc_finish_data(struct bcm2835_host *host)
-+{
-+ struct mmc_data *data;
-+
-+ BUG_ON(!host->data);
-+
-+ data = host->data;
-+ host->data = NULL;
-+
-+ if (data->error)
-+ data->bytes_xfered = 0;
-+ else
-+ data->bytes_xfered = data->blksz * data->blocks;
-+
-+ /*
-+ * Need to send CMD12 if -
-+ * a) open-ended multiblock transfer (no CMD23)
-+ * b) error in multiblock transfer
-+ */
-+ if (data->stop &&
-+ (data->error ||
-+ !host->mrq->sbc)) {
-+
-+ /*
-+ * The controller needs a reset of internal state machines
-+ * upon error conditions.
-+ */
-+ if (data->error) {
-+ bcm2835_mmc_reset(host, SDHCI_RESET_CMD);
-+ bcm2835_mmc_reset(host, SDHCI_RESET_DATA);
-+ }
-+
-+ bcm2835_mmc_send_command(host, data->stop);
-+ } else
-+ tasklet_schedule(&host->finish_tasklet);
-+}
-+
-+static void bcm2835_mmc_finish_command(struct bcm2835_host *host)
-+{
-+ int i;
-+
-+ BUG_ON(host->cmd == NULL);
-+
-+ if (host->cmd->flags & MMC_RSP_PRESENT) {
-+ if (host->cmd->flags & MMC_RSP_136) {
-+ /* CRC is stripped so we need to do some shifting. */
-+ for (i = 0; i < 4; i++) {
-+ host->cmd->resp[i] = bcm2835_mmc_readl(host,
-+ SDHCI_RESPONSE + (3-i)*4) << 8;
-+ if (i != 3)
-+ host->cmd->resp[i] |=
-+ bcm2835_mmc_readb(host,
-+ SDHCI_RESPONSE + (3-i)*4-1);
-+ }
-+ } else {
-+ host->cmd->resp[0] = bcm2835_mmc_readl(host, SDHCI_RESPONSE);
-+ }
-+ }
-+
-+ host->cmd->error = 0;
-+
-+ /* Finished CMD23, now send actual command. */
-+ if (host->cmd == host->mrq->sbc) {
-+ host->cmd = NULL;
-+ bcm2835_mmc_send_command(host, host->mrq->cmd);
-+
-+ if (host->mrq->cmd->data && host->use_dma) {
-+ /* DMA transfer starts now, PIO starts after interrupt */
-+ bcm2835_mmc_transfer_dma(host);
-+ }
-+ } else {
-+
-+ /* Processed actual command. */
-+ if (host->data && host->data_early)
-+ bcm2835_mmc_finish_data(host);
-+
-+ if (!host->cmd->data)
-+ tasklet_schedule(&host->finish_tasklet);
-+
-+ host->cmd = NULL;
-+ }
-+}
-+
-+
-+static void bcm2835_mmc_timeout_timer(unsigned long data)
-+{
-+ struct bcm2835_host *host;
-+ unsigned long flags;
-+
-+ host = (struct bcm2835_host *)data;
-+
-+ spin_lock_irqsave(&host->lock, flags);
-+
-+ if (host->mrq) {
-+ pr_err("%s: Timeout waiting for hardware interrupt.\n",
-+ mmc_hostname(host->mmc));
-+ bcm2835_mmc_dumpregs(host);
-+
-+ if (host->data) {
-+ host->data->error = -ETIMEDOUT;
-+ bcm2835_mmc_finish_data(host);
-+ } else {
-+ if (host->cmd)
-+ host->cmd->error = -ETIMEDOUT;
-+ else
-+ host->mrq->cmd->error = -ETIMEDOUT;
-+
-+ tasklet_schedule(&host->finish_tasklet);
-+ }
-+ }
-+
-+ mmiowb();
-+ spin_unlock_irqrestore(&host->lock, flags);
-+}
-+
-+
-+static void bcm2835_mmc_enable_sdio_irq_nolock(struct bcm2835_host *host, int enable)
-+{
-+ if (!(host->flags & SDHCI_DEVICE_DEAD)) {
-+ if (enable)
-+ host->ier |= SDHCI_INT_CARD_INT;
-+ else
-+ host->ier &= ~SDHCI_INT_CARD_INT;
-+
-+ bcm2835_mmc_writel(host, host->ier, SDHCI_INT_ENABLE, 7);
-+ bcm2835_mmc_writel(host, host->ier, SDHCI_SIGNAL_ENABLE, 7);
-+ mmiowb();
-+ }
-+}
-+
-+static void bcm2835_mmc_enable_sdio_irq(struct mmc_host *mmc, int enable)
-+{
-+ struct bcm2835_host *host = mmc_priv(mmc);
-+ unsigned long flags;
-+
-+ spin_lock_irqsave(&host->lock, flags);
-+ if (enable)
-+ host->flags |= SDHCI_SDIO_IRQ_ENABLED;
-+ else
-+ host->flags &= ~SDHCI_SDIO_IRQ_ENABLED;
-+
-+ bcm2835_mmc_enable_sdio_irq_nolock(host, enable);
-+ spin_unlock_irqrestore(&host->lock, flags);
-+}
-+
-+static void bcm2835_mmc_cmd_irq(struct bcm2835_host *host, u32 intmask)
-+{
-+
-+ BUG_ON(intmask == 0);
-+
-+ if (!host->cmd) {
-+ pr_err("%s: Got command interrupt 0x%08x even "
-+ "though no command operation was in progress.\n",
-+ mmc_hostname(host->mmc), (unsigned)intmask);
-+ bcm2835_mmc_dumpregs(host);
-+ return;
-+ }
-+
-+ if (intmask & SDHCI_INT_TIMEOUT)
-+ host->cmd->error = -ETIMEDOUT;
-+ else if (intmask & (SDHCI_INT_CRC | SDHCI_INT_END_BIT |
-+ SDHCI_INT_INDEX)) {
-+ host->cmd->error = -EILSEQ;
-+ }
-+
-+ if (host->cmd->error) {
-+ tasklet_schedule(&host->finish_tasklet);
-+ return;
-+ }
-+
-+ if (intmask & SDHCI_INT_RESPONSE)
-+ bcm2835_mmc_finish_command(host);
-+
-+}
-+
-+static void bcm2835_mmc_data_irq(struct bcm2835_host *host, u32 intmask)
-+{
-+ struct dma_chan *dma_chan;
-+ u32 dir_data;
-+
-+ BUG_ON(intmask == 0);
-+
-+ if (!host->data) {
-+ /*
-+ * The "data complete" interrupt is also used to
-+ * indicate that a busy state has ended. See comment
-+ * above in sdhci_cmd_irq().
-+ */
-+ if (host->cmd && (host->cmd->flags & MMC_RSP_BUSY)) {
-+ if (intmask & SDHCI_INT_DATA_END) {
-+ bcm2835_mmc_finish_command(host);
-+ return;
-+ }
-+ }
-+
-+ pr_debug("%s: Got data interrupt 0x%08x even "
-+ "though no data operation was in progress.\n",
-+ mmc_hostname(host->mmc), (unsigned)intmask);
-+ bcm2835_mmc_dumpregs(host);
-+
-+ return;
-+ }
-+
-+ if (intmask & SDHCI_INT_DATA_TIMEOUT)
-+ host->data->error = -ETIMEDOUT;
-+ else if (intmask & SDHCI_INT_DATA_END_BIT)
-+ host->data->error = -EILSEQ;
-+ else if ((intmask & SDHCI_INT_DATA_CRC) &&
-+ SDHCI_GET_CMD(bcm2835_mmc_readw(host, SDHCI_COMMAND))
-+ != MMC_BUS_TEST_R)
-+ host->data->error = -EILSEQ;
-+
-+ if (host->use_dma) {
-+ if (host->data->flags & MMC_DATA_WRITE) {
-+ /* IRQ handled here */
-+
-+ dma_chan = host->dma_chan_tx;
-+ dir_data = DMA_TO_DEVICE;
-+ dma_unmap_sg(dma_chan->device->dev,
-+ host->data->sg, host->data->sg_len,
-+ dir_data);
-+
-+ bcm2835_mmc_finish_data(host);
-+ }
-+
-+ } else {
-+ if (host->data->error)
-+ bcm2835_mmc_finish_data(host);
-+ else {
-+ if (intmask & (SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL))
-+ bcm2835_mmc_transfer_pio(host);
-+
-+ if (intmask & SDHCI_INT_DATA_END) {
-+ if (host->cmd) {
-+ /*
-+ * Data managed to finish before the
-+ * command completed. Make sure we do
-+ * things in the proper order.
-+ */
-+ host->data_early = 1;
-+ } else {
-+ bcm2835_mmc_finish_data(host);
-+ }
-+ }
-+ }
-+ }
-+}
-+
-+
-+static irqreturn_t bcm2835_mmc_irq(int irq, void *dev_id)
-+{
-+ irqreturn_t result = IRQ_NONE;
-+ struct bcm2835_host *host = dev_id;
-+ u32 intmask, mask, unexpected = 0;
-+ int max_loops = 16;
-+
-+ spin_lock(&host->lock);
-+
-+ intmask = bcm2835_mmc_readl(host, SDHCI_INT_STATUS);
-+
-+ if (!intmask || intmask == 0xffffffff) {
-+ result = IRQ_NONE;
-+ goto out;
-+ }
-+
-+ do {
-+ /* Clear selected interrupts. */
-+ mask = intmask & (SDHCI_INT_CMD_MASK | SDHCI_INT_DATA_MASK |
-+ SDHCI_INT_BUS_POWER);
-+ bcm2835_mmc_writel(host, mask, SDHCI_INT_STATUS, 8);
-+
-+
-+ if (intmask & SDHCI_INT_CMD_MASK)
-+ bcm2835_mmc_cmd_irq(host, intmask & SDHCI_INT_CMD_MASK);
-+
-+ if (intmask & SDHCI_INT_DATA_MASK)
-+ bcm2835_mmc_data_irq(host, intmask & SDHCI_INT_DATA_MASK);
-+
-+ if (intmask & SDHCI_INT_BUS_POWER)
-+ pr_err("%s: Card is consuming too much power!\n",
-+ mmc_hostname(host->mmc));
-+
-+ if (intmask & SDHCI_INT_CARD_INT) {
-+ bcm2835_mmc_enable_sdio_irq_nolock(host, false);
-+ host->thread_isr |= SDHCI_INT_CARD_INT;
-+ result = IRQ_WAKE_THREAD;
-+ }
-+
-+ intmask &= ~(SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE |
-+ SDHCI_INT_CMD_MASK | SDHCI_INT_DATA_MASK |
-+ SDHCI_INT_ERROR | SDHCI_INT_BUS_POWER |
-+ SDHCI_INT_CARD_INT);
-+
-+ if (intmask) {
-+ unexpected |= intmask;
-+ bcm2835_mmc_writel(host, intmask, SDHCI_INT_STATUS, 9);
-+ }
-+
-+ if (result == IRQ_NONE)
-+ result = IRQ_HANDLED;
-+
-+ intmask = bcm2835_mmc_readl(host, SDHCI_INT_STATUS);
-+ } while (intmask && --max_loops);
-+out:
-+ spin_unlock(&host->lock);
-+
-+ if (unexpected) {
-+ pr_err("%s: Unexpected interrupt 0x%08x.\n",
-+ mmc_hostname(host->mmc), unexpected);
-+ bcm2835_mmc_dumpregs(host);
-+ }
-+
-+ return result;
-+}
-+
-+static irqreturn_t bcm2835_mmc_thread_irq(int irq, void *dev_id)
-+{
-+ struct bcm2835_host *host = dev_id;
-+ unsigned long flags;
-+ u32 isr;
-+
-+ spin_lock_irqsave(&host->lock, flags);
-+ isr = host->thread_isr;
-+ host->thread_isr = 0;
-+ spin_unlock_irqrestore(&host->lock, flags);
-+
-+ if (isr & SDHCI_INT_CARD_INT) {
-+ sdio_run_irqs(host->mmc);
-+
-+ spin_lock_irqsave(&host->lock, flags);
-+ if (host->flags & SDHCI_SDIO_IRQ_ENABLED)
-+ bcm2835_mmc_enable_sdio_irq_nolock(host, true);
-+ spin_unlock_irqrestore(&host->lock, flags);
-+ }
-+
-+ return isr ? IRQ_HANDLED : IRQ_NONE;
-+}
-+
-+
-+
-+void bcm2835_mmc_set_clock(struct bcm2835_host *host, unsigned int clock)
-+{
-+ int div = 0; /* Initialized for compiler warning */
-+ int real_div = div, clk_mul = 1;
-+ u16 clk = 0;
-+ unsigned long timeout;
-+ unsigned int input_clock = clock;
-+
-+ if (host->overclock_50 && (clock == 50000000))
-+ clock = host->overclock_50 * 1000000 + 999999;
-+
-+ host->mmc->actual_clock = 0;
-+
-+ bcm2835_mmc_writew(host, 0, SDHCI_CLOCK_CONTROL);
-+
-+ if (clock == 0)
-+ return;
-+
-+ /* Version 3.00 divisors must be a multiple of 2. */
-+ if (host->max_clk <= clock)
-+ div = 1;
-+ else {
-+ for (div = 2; div < SDHCI_MAX_DIV_SPEC_300;
-+ div += 2) {
-+ if ((host->max_clk / div) <= clock)
-+ break;
-+ }
-+ }
-+
-+ real_div = div;
-+ div >>= 1;
-+
-+ if (real_div)
-+ clock = (host->max_clk * clk_mul) / real_div;
-+ host->mmc->actual_clock = clock;
-+
-+ if ((clock > input_clock) && (clock > host->max_overclock)) {
-+ pr_warn("%s: Overclocking to %dHz\n",
-+ mmc_hostname(host->mmc), clock);
-+ host->max_overclock = clock;
-+ }
-+
-+ clk |= (div & SDHCI_DIV_MASK) << SDHCI_DIVIDER_SHIFT;
-+ clk |= ((div & SDHCI_DIV_HI_MASK) >> SDHCI_DIV_MASK_LEN)
-+ << SDHCI_DIVIDER_HI_SHIFT;
-+ clk |= SDHCI_CLOCK_INT_EN;
-+ bcm2835_mmc_writew(host, clk, SDHCI_CLOCK_CONTROL);
-+
-+ /* Wait max 20 ms */
-+ timeout = 20;
-+ while (!((clk = bcm2835_mmc_readw(host, SDHCI_CLOCK_CONTROL))
-+ & SDHCI_CLOCK_INT_STABLE)) {
-+ if (timeout == 0) {
-+ pr_err("%s: Internal clock never "
-+ "stabilised.\n", mmc_hostname(host->mmc));
-+ bcm2835_mmc_dumpregs(host);
-+ return;
-+ }
-+ timeout--;
-+ mdelay(1);
-+ }
-+
-+ if (20-timeout > 10 && 20-timeout > host->max_delay) {
-+ host->max_delay = 20-timeout;
-+ pr_warning("Warning: MMC controller hung for %d ms\n", host->max_delay);
-+ }
-+
-+ clk |= SDHCI_CLOCK_CARD_EN;
-+ bcm2835_mmc_writew(host, clk, SDHCI_CLOCK_CONTROL);
-+}
-+
-+static void bcm2835_mmc_request(struct mmc_host *mmc, struct mmc_request *mrq)
-+{
-+ struct bcm2835_host *host;
-+ unsigned long flags;
-+
-+ host = mmc_priv(mmc);
-+
-+ spin_lock_irqsave(&host->lock, flags);
-+
-+ WARN_ON(host->mrq != NULL);
-+
-+ host->mrq = mrq;
-+
-+ if (mrq->sbc && !(host->flags & SDHCI_AUTO_CMD23))
-+ bcm2835_mmc_send_command(host, mrq->sbc);
-+ else
-+ bcm2835_mmc_send_command(host, mrq->cmd);
-+
-+ mmiowb();
-+ spin_unlock_irqrestore(&host->lock, flags);
-+
-+ if (!(mrq->sbc && !(host->flags & SDHCI_AUTO_CMD23)) && mrq->cmd->data && host->use_dma) {
-+ /* DMA transfer starts now, PIO starts after interrupt */
-+ bcm2835_mmc_transfer_dma(host);
-+ }
-+}
-+
-+
-+static void bcm2835_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
-+{
-+
-+ struct bcm2835_host *host = mmc_priv(mmc);
-+ unsigned long flags;
-+ u8 ctrl;
-+ u16 clk, ctrl_2;
-+
-+ pr_debug("bcm2835_mmc_set_ios: clock %d, pwr %d, bus_width %d, timing %d, vdd %d, drv_type %d\n",
-+ ios->clock, ios->power_mode, ios->bus_width,
-+ ios->timing, ios->signal_voltage, ios->drv_type);
-+
-+ spin_lock_irqsave(&host->lock, flags);
-+
-+ if (!ios->clock || ios->clock != host->clock) {
-+ bcm2835_mmc_set_clock(host, ios->clock);
-+ host->clock = ios->clock;
-+ }
-+
-+ if (host->pwr != SDHCI_POWER_330) {
-+ host->pwr = SDHCI_POWER_330;
-+ bcm2835_mmc_writeb(host, SDHCI_POWER_330 | SDHCI_POWER_ON, SDHCI_POWER_CONTROL);
-+ }
-+
-+ ctrl = bcm2835_mmc_readb(host, SDHCI_HOST_CONTROL);
-+
-+ /* set bus width */
-+ ctrl &= ~SDHCI_CTRL_8BITBUS;
-+ if (ios->bus_width == MMC_BUS_WIDTH_4)
-+ ctrl |= SDHCI_CTRL_4BITBUS;
-+ else
-+ ctrl &= ~SDHCI_CTRL_4BITBUS;
-+
-+ ctrl &= ~SDHCI_CTRL_HISPD; /* NO_HISPD_BIT */
-+
-+
-+ bcm2835_mmc_writeb(host, ctrl, SDHCI_HOST_CONTROL);
-+ /*
-+ * We only need to set Driver Strength if the
-+ * preset value enable is not set.
-+ */
-+ ctrl_2 = bcm2835_mmc_readw(host, SDHCI_HOST_CONTROL2);
-+ ctrl_2 &= ~SDHCI_CTRL_DRV_TYPE_MASK;
-+ if (ios->drv_type == MMC_SET_DRIVER_TYPE_A)
-+ ctrl_2 |= SDHCI_CTRL_DRV_TYPE_A;
-+ else if (ios->drv_type == MMC_SET_DRIVER_TYPE_C)
-+ ctrl_2 |= SDHCI_CTRL_DRV_TYPE_C;
-+
-+ bcm2835_mmc_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
-+
-+ /* Reset SD Clock Enable */
-+ clk = bcm2835_mmc_readw(host, SDHCI_CLOCK_CONTROL);
-+ clk &= ~SDHCI_CLOCK_CARD_EN;
-+ bcm2835_mmc_writew(host, clk, SDHCI_CLOCK_CONTROL);
-+
-+ /* Re-enable SD Clock */
-+ bcm2835_mmc_set_clock(host, host->clock);
-+ bcm2835_mmc_writeb(host, ctrl, SDHCI_HOST_CONTROL);
-+
-+ mmiowb();
-+
-+ spin_unlock_irqrestore(&host->lock, flags);
-+}
-+
-+
-+static struct mmc_host_ops bcm2835_ops = {
-+ .request = bcm2835_mmc_request,
-+ .set_ios = bcm2835_mmc_set_ios,
-+ .enable_sdio_irq = bcm2835_mmc_enable_sdio_irq,
-+};
-+
-+
-+static void bcm2835_mmc_tasklet_finish(unsigned long param)
-+{
-+ struct bcm2835_host *host;
-+ unsigned long flags;
-+ struct mmc_request *mrq;
-+
-+ host = (struct bcm2835_host *)param;
-+
-+ spin_lock_irqsave(&host->lock, flags);
-+
-+ /*
-+ * If this tasklet gets rescheduled while running, it will
-+ * be run again afterwards but without any active request.
-+ */
-+ if (!host->mrq) {
-+ spin_unlock_irqrestore(&host->lock, flags);
-+ return;
-+ }
-+
-+ del_timer(&host->timer);
-+
-+ mrq = host->mrq;
-+
-+ /*
-+ * The controller needs a reset of internal state machines
-+ * upon error conditions.
-+ */
-+ if (!(host->flags & SDHCI_DEVICE_DEAD) &&
-+ ((mrq->cmd && mrq->cmd->error) ||
-+ (mrq->data && (mrq->data->error ||
-+ (mrq->data->stop && mrq->data->stop->error))))) {
-+
-+ spin_unlock_irqrestore(&host->lock, flags);
-+ bcm2835_mmc_reset(host, SDHCI_RESET_CMD);
-+ bcm2835_mmc_reset(host, SDHCI_RESET_DATA);
-+ spin_lock_irqsave(&host->lock, flags);
-+ }
-+
-+ host->mrq = NULL;
-+ host->cmd = NULL;
-+ host->data = NULL;
-+
-+ mmiowb();
-+
-+ spin_unlock_irqrestore(&host->lock, flags);
-+ mmc_request_done(host->mmc, mrq);
-+}
-+
-+
-+
-+static int bcm2835_mmc_add_host(struct bcm2835_host *host)
-+{
-+ struct mmc_host *mmc = host->mmc;
-+ struct device *dev = mmc->parent;
-+#ifndef FORCE_PIO
-+ struct dma_slave_config cfg;
-+#endif
-+ int ret;
-+
-+ bcm2835_mmc_reset(host, SDHCI_RESET_ALL);
-+
-+ host->clk_mul = 0;
-+
-+ mmc->f_max = host->max_clk;
-+ mmc->f_max = host->max_clk;
-+ mmc->f_min = host->max_clk / SDHCI_MAX_DIV_SPEC_300;
-+
-+ /* SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK */
-+ host->timeout_clk = mmc->f_max / 1000;
-+ mmc->max_busy_timeout = (1 << 27) / host->timeout_clk;
-+
-+ /* host controller capabilities */
-+ mmc->caps |= MMC_CAP_CMD23 | MMC_CAP_ERASE | MMC_CAP_NEEDS_POLL |
-+ MMC_CAP_SDIO_IRQ | MMC_CAP_SD_HIGHSPEED |
-+ MMC_CAP_MMC_HIGHSPEED | MMC_CAP_4_BIT_DATA;
-+
-+ mmc->caps2 |= MMC_CAP2_SDIO_IRQ_NOTHREAD;
-+
-+ host->flags = SDHCI_AUTO_CMD23;
-+
-+ dev_info(dev, "mmc_debug:%x mmc_debug2:%x\n", mmc_debug, mmc_debug2);
-+#ifdef FORCE_PIO
-+ dev_info(dev, "Forcing PIO mode\n");
-+ host->have_dma = false;
-+#else
-+ if (IS_ERR_OR_NULL(host->dma_chan_tx) ||
-+ IS_ERR_OR_NULL(host->dma_chan_rx)) {
-+ dev_err(dev, "%s: Unable to initialise DMA channels. Falling back to PIO\n",
-+ DRIVER_NAME);
-+ host->have_dma = false;
-+ } else {
-+ dev_info(dev, "DMA channels allocated");
-+ host->have_dma = true;
-+
-+ cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
-+ cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
-+ cfg.slave_id = 11; /* DREQ channel */
-+
-+ cfg.direction = DMA_MEM_TO_DEV;
-+ cfg.src_addr = 0;
-+ cfg.dst_addr = host->bus_addr + SDHCI_BUFFER;
-+ ret = dmaengine_slave_config(host->dma_chan_tx, &cfg);
-+
-+ cfg.direction = DMA_DEV_TO_MEM;
-+ cfg.src_addr = host->bus_addr + SDHCI_BUFFER;
-+ cfg.dst_addr = 0;
-+ ret = dmaengine_slave_config(host->dma_chan_rx, &cfg);
-+ }
-+#endif
-+ mmc->max_segs = 128;
-+ mmc->max_req_size = 524288;
-+ mmc->max_seg_size = mmc->max_req_size;
-+ mmc->max_blk_size = 512;
-+ mmc->max_blk_count = 65535;
-+
-+ /* report supported voltage ranges */
-+ mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
-+
-+ tasklet_init(&host->finish_tasklet,
-+ bcm2835_mmc_tasklet_finish, (unsigned long)host);
-+
-+ setup_timer(&host->timer, bcm2835_mmc_timeout_timer, (unsigned long)host);
-+ init_waitqueue_head(&host->buf_ready_int);
-+
-+ bcm2835_mmc_init(host, 0);
-+ ret = devm_request_threaded_irq(dev, host->irq, bcm2835_mmc_irq,
-+ bcm2835_mmc_thread_irq, IRQF_SHARED,
-+ mmc_hostname(mmc), host);
-+ if (ret) {
-+ dev_err(dev, "Failed to request IRQ %d: %d\n", host->irq, ret);
-+ goto untasklet;
-+ }
-+
-+ mmiowb();
-+ mmc_add_host(mmc);
-+
-+ return 0;
-+
-+untasklet:
-+ tasklet_kill(&host->finish_tasklet);
-+
-+ return ret;
-+}
-+
-+static int bcm2835_mmc_probe(struct platform_device *pdev)
-+{
-+ struct device *dev = &pdev->dev;
-+ struct device_node *node = dev->of_node;
-+ struct clk *clk;
-+ struct resource *iomem;
-+ struct bcm2835_host *host;
-+ struct mmc_host *mmc;
-+ const __be32 *addr;
-+ int ret;
-+
-+ mmc = mmc_alloc_host(sizeof(*host), dev);
-+ if (!mmc)
-+ return -ENOMEM;
-+
-+ mmc->ops = &bcm2835_ops;
-+ host = mmc_priv(mmc);
-+ host->mmc = mmc;
-+ host->timeout = msecs_to_jiffies(1000);
-+ spin_lock_init(&host->lock);
-+
-+ iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+ host->ioaddr = devm_ioremap_resource(dev, iomem);
-+ if (IS_ERR(host->ioaddr)) {
-+ ret = PTR_ERR(host->ioaddr);
-+ goto err;
-+ }
-+
-+ addr = of_get_address(node, 0, NULL, NULL);
-+ if (!addr) {
-+ dev_err(dev, "could not get DMA-register address\n");
-+ return -ENODEV;
-+ }
-+ host->bus_addr = be32_to_cpup(addr);
-+ pr_debug(" - ioaddr %lx, iomem->start %lx, bus_addr %lx\n",
-+ (unsigned long)host->ioaddr,
-+ (unsigned long)iomem->start,
-+ (unsigned long)host->bus_addr);
-+
-+#ifndef FORCE_PIO
-+ if (node) {
-+ host->dma_chan_tx = dma_request_slave_channel(dev, "tx");
-+ host->dma_chan_rx = dma_request_slave_channel(dev, "rx");
-+ } else {
-+ dma_cap_mask_t mask;
-+
-+ dma_cap_zero(mask);
-+ /* we don't care about the channel, any would work */
-+ dma_cap_set(DMA_SLAVE, mask);
-+ host->dma_chan_tx = dma_request_channel(mask, NULL, NULL);
-+ host->dma_chan_rx = dma_request_channel(mask, NULL, NULL);
-+ }
-+#endif
-+ clk = devm_clk_get(dev, NULL);
-+ if (IS_ERR(clk)) {
-+ dev_err(dev, "could not get clk\n");
-+ ret = PTR_ERR(clk);
-+ goto err;
-+ }
-+
-+ host->max_clk = clk_get_rate(clk);
-+
-+ host->irq = platform_get_irq(pdev, 0);
-+ if (host->irq <= 0) {
-+ dev_err(dev, "get IRQ failed\n");
-+ ret = -EINVAL;
-+ goto err;
-+ }
-+
-+ if (node) {
-+ mmc_of_parse(mmc);
-+
-+ /* Read any custom properties */
-+ of_property_read_u32(node,
-+ "brcm,overclock-50",
-+ &host->overclock_50);
-+ } else {
-+ mmc->caps |= MMC_CAP_4_BIT_DATA;
-+ }
-+
-+ ret = bcm2835_mmc_add_host(host);
-+ if (ret)
-+ goto err;
-+
-+ platform_set_drvdata(pdev, host);
-+
-+ return 0;
-+err:
-+ mmc_free_host(mmc);
-+
-+ return ret;
-+}
-+
-+static int bcm2835_mmc_remove(struct platform_device *pdev)
-+{
-+ struct bcm2835_host *host = platform_get_drvdata(pdev);
-+ unsigned long flags;
-+ int dead;
-+ u32 scratch;
-+
-+ dead = 0;
-+ scratch = bcm2835_mmc_readl(host, SDHCI_INT_STATUS);
-+ if (scratch == (u32)-1)
-+ dead = 1;
-+
-+
-+ if (dead) {
-+ spin_lock_irqsave(&host->lock, flags);
-+
-+ host->flags |= SDHCI_DEVICE_DEAD;
-+
-+ if (host->mrq) {
-+ pr_err("%s: Controller removed during "
-+ " transfer!\n", mmc_hostname(host->mmc));
-+
-+ host->mrq->cmd->error = -ENOMEDIUM;
-+ tasklet_schedule(&host->finish_tasklet);
-+ }
-+
-+ spin_unlock_irqrestore(&host->lock, flags);
-+ }
-+
-+ mmc_remove_host(host->mmc);
-+
-+ if (!dead)
-+ bcm2835_mmc_reset(host, SDHCI_RESET_ALL);
-+
-+ free_irq(host->irq, host);
-+
-+ del_timer_sync(&host->timer);
-+
-+ tasklet_kill(&host->finish_tasklet);
-+
-+ mmc_free_host(host->mmc);
-+ platform_set_drvdata(pdev, NULL);
-+
-+ return 0;
-+}
-+
-+
-+static const struct of_device_id bcm2835_mmc_match[] = {
-+ { .compatible = "brcm,bcm2835-mmc" },
-+ { }
-+};
-+MODULE_DEVICE_TABLE(of, bcm2835_mmc_match);
-+
-+
-+
-+static struct platform_driver bcm2835_mmc_driver = {
-+ .probe = bcm2835_mmc_probe,
-+ .remove = bcm2835_mmc_remove,
-+ .driver = {
-+ .name = DRIVER_NAME,
-+ .owner = THIS_MODULE,
-+ .of_match_table = bcm2835_mmc_match,
-+ },
-+};
-+module_platform_driver(bcm2835_mmc_driver);
-+
-+module_param(mmc_debug, uint, 0644);
-+module_param(mmc_debug2, uint, 0644);
-+MODULE_ALIAS("platform:mmc-bcm2835");
-+MODULE_DESCRIPTION("BCM2835 SDHCI driver");
-+MODULE_LICENSE("GPL v2");
-+MODULE_AUTHOR("Gellert Weisz");
diff --git a/target/linux/brcm2708/patches-4.4/0033-Adding-bcm2835-sdhost-driver-and-an-overlay-to-enabl.patch b/target/linux/brcm2708/patches-4.4/0033-Adding-bcm2835-sdhost-driver-and-an-overlay-to-enabl.patch
deleted file mode 100644
index fc23d5b..0000000
--- a/target/linux/brcm2708/patches-4.4/0033-Adding-bcm2835-sdhost-driver-and-an-overlay-to-enabl.patch
+++ /dev/null
@@ -1,2021 +0,0 @@
-From 81c93790b30530e11b744828d196d011a7dcaa5f Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Wed, 25 Mar 2015 17:49:47 +0000
-Subject: [PATCH] Adding bcm2835-sdhost driver, and an overlay to enable it
-
-BCM2835 has two SD card interfaces. This driver uses the other one.
-
-bcm2835-sdhost: Error handling fix, and code clarification
-
-bcm2835-sdhost: Adding overclocking option
-
-Allow a different clock speed to be substitued for a requested 50MHz.
-This option is exposed using the "overclock_50" DT parameter.
-Note that the sdhost interface is restricted to integer divisions of
-core_freq, and the highest sensible option for a core_freq of 250MHz
-is 84 (250/3 = 83.3MHz), the next being 125 (250/2) which is much too
-high.
-
-Use at your own risk.
-
-bcm2835-sdhost: Round up the overclock, so 62 works for 62.5Mhz
-
-Also only warn once for each overclock setting.
-
-bcm2835-sdhost: Improve error handling and recovery
-
-1) Expose the hw_reset method to the MMC framework, removing many
- internal calls by the driver.
-
-2) Reduce overclock setting on error.
-
-3) Increase timeout to cope with high capacity cards.
-
-4) Add properties and parameters to control pio_limit and debug.
-
-5) Reduce messages at probe time.
-
-bcm2835-sdhost: Further improve overclock back-off
-
-bcm2835-sdhost: Clear HBLC for PIO mode
-
-Also update pio_limit default in overlay README.
-
-bcm2835-sdhost: Add the ERASE capability
-
-See: https://github.com/raspberrypi/linux/issues/1076
-
-bcm2835-sdhost: Ignore CRC7 for MMC CMD1
-
-It seems that the sdhost interface returns CRC7 errors for CMD1,
-which is the MMC-specific SEND_OP_COND. Returning these errors to
-the MMC layer causes a downward spiral, but ignoring them seems
-to be harmless.
-
-bcm2835-mmc/sdhost: Remove ARCH_BCM2835 differences
-
-The bcm2835-mmc driver (and -sdhost driver that copied from it)
-contains code to handle SDIO interrupts in a threaded interrupt
-handler rather than waking the MMC framework thread. The change
-follows a patch from Russell King that adds the facility as the
-preferred way of working.
-
-However, the new code path is only present in ARCH_BCM2835
-builds, which I have taken to be a way of testing the waters
-rather than making the change across the board; I can't see
-any technical reason why it wouldn't be enabled for MACH_BCM270X
-builds. So this patch standardises on the ARCH_BCM2835 code,
-removing the old code paths.
-
-bcm2835-sdhost: Don't log timeout errors unless debug=1
-
-The MMC card-discovery process generates timeouts. This is
-expected behaviour, so reporting it to the user serves no purpose.
-Suppress the reporting of timeout errors unless the debug flag
-is on.
----
- drivers/mmc/host/Kconfig | 10 +
- drivers/mmc/host/Makefile | 1 +
- drivers/mmc/host/bcm2835-sdhost.c | 1907 +++++++++++++++++++++++++++++++++++++
- 3 files changed, 1918 insertions(+)
- create mode 100644 drivers/mmc/host/bcm2835-sdhost.c
-
---- a/drivers/mmc/host/Kconfig
-+++ b/drivers/mmc/host/Kconfig
-@@ -33,6 +33,16 @@ config MMC_BCM2835_PIO_DMA_BARRIER
-
- If unsure, say 2 here.
-
-+config MMC_BCM2835_SDHOST
-+ tristate "Support for the SDHost controller on BCM2708/9"
-+ depends on MACH_BCM2708 || MACH_BCM2709 || ARCH_BCM2835
-+ help
-+ This selects the SDHost controller on BCM2835/6.
-+
-+ If you have a controller with this interface, say Y or M here.
-+
-+ If unsure, say N.
-+
- config MMC_ARMMMCI
- tristate "ARM AMBA Multimedia Card Interface support"
- depends on ARM_AMBA
---- a/drivers/mmc/host/Makefile
-+++ b/drivers/mmc/host/Makefile
-@@ -18,6 +18,7 @@ obj-$(CONFIG_MMC_SDHCI_S3C) += sdhci-s3c
- obj-$(CONFIG_MMC_SDHCI_SIRF) += sdhci-sirf.o
- obj-$(CONFIG_MMC_SDHCI_F_SDH30) += sdhci_f_sdh30.o
- obj-$(CONFIG_MMC_SDHCI_SPEAR) += sdhci-spear.o
-+obj-$(CONFIG_MMC_BCM2835_SDHOST) += bcm2835-sdhost.o
- obj-$(CONFIG_MMC_BCM2835) += bcm2835-mmc.o
- obj-$(CONFIG_MMC_WBSD) += wbsd.o
- obj-$(CONFIG_MMC_AU1X) += au1xmmc.o
---- /dev/null
-+++ b/drivers/mmc/host/bcm2835-sdhost.c
-@@ -0,0 +1,1907 @@
-+/*
-+ * BCM2835 SD host driver.
-+ *
-+ * Author: Phil Elwell <phil at raspberrypi.org>
-+ * Copyright 2015
-+ *
-+ * Based on
-+ * mmc-bcm2835.c by Gellert Weisz
-+ * which is, in turn, based on
-+ * sdhci-bcm2708.c by Broadcom
-+ * sdhci-bcm2835.c by Stephen Warren and Oleksandr Tymoshenko
-+ * sdhci.c and sdhci-pci.c by Pierre Ossman
-+ *
-+ * This program is free software; you can redistribute it and/or modify it
-+ * under the terms and conditions of the GNU General Public License,
-+ * version 2, as published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope it will be useful, but WITHOUT
-+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
-+ * more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
-+ */
-+
-+#define SAFE_READ_THRESHOLD 4
-+#define SAFE_WRITE_THRESHOLD 4
-+#define ALLOW_DMA 1
-+#define ALLOW_CMD23 0
-+#define ALLOW_FAST 1
-+#define USE_BLOCK_IRQ 1
-+
-+#include <linux/delay.h>
-+#include <linux/module.h>
-+#include <linux/io.h>
-+#include <linux/mmc/mmc.h>
-+#include <linux/mmc/host.h>
-+#include <linux/mmc/sd.h>
-+#include <linux/scatterlist.h>
-+#include <linux/of_address.h>
-+#include <linux/of_irq.h>
-+#include <linux/clk.h>
-+#include <linux/platform_device.h>
-+#include <linux/err.h>
-+#include <linux/blkdev.h>
-+#include <linux/dmaengine.h>
-+#include <linux/dma-mapping.h>
-+#include <linux/of_dma.h>
-+#include <linux/time.h>
-+
-+#define DRIVER_NAME "sdhost-bcm2835"
-+
-+#define SDCMD 0x00 /* Command to SD card - 16 R/W */
-+#define SDARG 0x04 /* Argument to SD card - 32 R/W */
-+#define SDTOUT 0x08 /* Start value for timeout counter - 32 R/W */
-+#define SDCDIV 0x0c /* Start value for clock divider - 11 R/W */
-+#define SDRSP0 0x10 /* SD card response (31:0) - 32 R */
-+#define SDRSP1 0x14 /* SD card response (63:32) - 32 R */
-+#define SDRSP2 0x18 /* SD card response (95:64) - 32 R */
-+#define SDRSP3 0x1c /* SD card response (127:96) - 32 R */
-+#define SDHSTS 0x20 /* SD host status - 11 R */
-+#define SDVDD 0x30 /* SD card power control - 1 R/W */
-+#define SDEDM 0x34 /* Emergency Debug Mode - 13 R/W */
-+#define SDHCFG 0x38 /* Host configuration - 2 R/W */
-+#define SDHBCT 0x3c /* Host byte count (debug) - 32 R/W */
-+#define SDDATA 0x40 /* Data to/from SD card - 32 R/W */
-+#define SDHBLC 0x50 /* Host block count (SDIO/SDHC) - 9 R/W */
-+
-+#define SDCMD_NEW_FLAG 0x8000
-+#define SDCMD_FAIL_FLAG 0x4000
-+#define SDCMD_BUSYWAIT 0x800
-+#define SDCMD_NO_RESPONSE 0x400
-+#define SDCMD_LONG_RESPONSE 0x200
-+#define SDCMD_WRITE_CMD 0x80
-+#define SDCMD_READ_CMD 0x40
-+#define SDCMD_CMD_MASK 0x3f
-+
-+#define SDCDIV_MAX_CDIV 0x7ff
-+
-+#define SDHSTS_BUSY_IRPT 0x400
-+#define SDHSTS_BLOCK_IRPT 0x200
-+#define SDHSTS_SDIO_IRPT 0x100
-+#define SDHSTS_REW_TIME_OUT 0x80
-+#define SDHSTS_CMD_TIME_OUT 0x40
-+#define SDHSTS_CRC16_ERROR 0x20
-+#define SDHSTS_CRC7_ERROR 0x10
-+#define SDHSTS_FIFO_ERROR 0x08
-+/* Reserved */
-+/* Reserved */
-+#define SDHSTS_DATA_FLAG 0x01
-+
-+#define SDHSTS_TRANSFER_ERROR_MASK (SDHSTS_CRC7_ERROR|SDHSTS_CRC16_ERROR|SDHSTS_REW_TIME_OUT|SDHSTS_FIFO_ERROR)
-+#define SDHSTS_ERROR_MASK (SDHSTS_CMD_TIME_OUT|SDHSTS_TRANSFER_ERROR_MASK)
-+
-+#define SDHCFG_BUSY_IRPT_EN (1<<10)
-+#define SDHCFG_BLOCK_IRPT_EN (1<<8)
-+#define SDHCFG_SDIO_IRPT_EN (1<<5)
-+#define SDHCFG_DATA_IRPT_EN (1<<4)
-+#define SDHCFG_SLOW_CARD (1<<3)
-+#define SDHCFG_WIDE_EXT_BUS (1<<2)
-+#define SDHCFG_WIDE_INT_BUS (1<<1)
-+#define SDHCFG_REL_CMD_LINE (1<<0)
-+
-+#define SDEDM_FORCE_DATA_MODE (1<<19)
-+#define SDEDM_CLOCK_PULSE (1<<20)
-+#define SDEDM_BYPASS (1<<21)
-+
-+#define SDEDM_WRITE_THRESHOLD_SHIFT 9
-+#define SDEDM_READ_THRESHOLD_SHIFT 14
-+#define SDEDM_THRESHOLD_MASK 0x1f
-+
-+#define MHZ 1000000
-+
-+
-+struct bcm2835_host {
-+ spinlock_t lock;
-+
-+ void __iomem *ioaddr;
-+ u32 bus_addr;
-+
-+ struct mmc_host *mmc;
-+
-+ u32 pio_timeout; /* In jiffies */
-+
-+ int clock; /* Current clock speed */
-+
-+ bool slow_card; /* Force 11-bit divisor */
-+
-+ unsigned int max_clk; /* Max possible freq */
-+
-+ struct tasklet_struct finish_tasklet; /* Tasklet structures */
-+
-+ struct timer_list timer; /* Timer for timeouts */
-+
-+ struct timer_list pio_timer; /* PIO error detection timer */
-+
-+ struct sg_mapping_iter sg_miter; /* SG state for PIO */
-+ unsigned int blocks; /* remaining PIO blocks */
-+
-+ int irq; /* Device IRQ */
-+
-+
-+ /* cached registers */
-+ u32 hcfg;
-+ u32 cdiv;
-+
-+ struct mmc_request *mrq; /* Current request */
-+ struct mmc_command *cmd; /* Current command */
-+ struct mmc_data *data; /* Current data request */
-+ unsigned int data_complete:1; /* Data finished before cmd */
-+
-+ unsigned int flush_fifo:1; /* Drain the fifo when finishing */
-+
-+ unsigned int use_busy:1; /* Wait for busy interrupt */
-+
-+ unsigned int debug:1; /* Enable debug output */
-+
-+ u32 thread_isr;
-+
-+ /*DMA part*/
-+ struct dma_chan *dma_chan_rx; /* DMA channel for reads */
-+ struct dma_chan *dma_chan_tx; /* DMA channel for writes */
-+
-+ bool allow_dma;
-+ bool have_dma;
-+ bool use_dma;
-+ /*end of DMA part*/
-+
-+ int max_delay; /* maximum length of time spent waiting */
-+ struct timeval stop_time; /* when the last stop was issued */
-+ u32 delay_after_stop; /* minimum time between stop and subsequent data transfer */
-+ u32 overclock_50; /* frequency to use when 50MHz is requested (in MHz) */
-+ u32 overclock; /* Current frequency if overclocked, else zero */
-+ u32 pio_limit; /* Maximum block count for PIO (0 = always DMA) */
-+};
-+
-+
-+static inline void bcm2835_sdhost_write(struct bcm2835_host *host, u32 val, int reg)
-+{
-+ writel(val, host->ioaddr + reg);
-+}
-+
-+static inline u32 bcm2835_sdhost_read(struct bcm2835_host *host, int reg)
-+{
-+ return readl(host->ioaddr + reg);
-+}
-+
-+static inline u32 bcm2835_sdhost_read_relaxed(struct bcm2835_host *host, int reg)
-+{
-+ return readl_relaxed(host->ioaddr + reg);
-+}
-+
-+static void bcm2835_sdhost_dumpcmd(struct bcm2835_host *host,
-+ struct mmc_command *cmd,
-+ const char *label)
-+{
-+ if (cmd)
-+ pr_info("%s:%c%s op %d arg 0x%x flags 0x%x - resp %08x %08x %08x %08x, err %d\n",
-+ mmc_hostname(host->mmc),
-+ (cmd == host->cmd) ? '>' : ' ',
-+ label, cmd->opcode, cmd->arg, cmd->flags,
-+ cmd->resp[0], cmd->resp[1], cmd->resp[2], cmd->resp[3],
-+ cmd->error);
-+}
-+
-+static void bcm2835_sdhost_dumpregs(struct bcm2835_host *host)
-+{
-+ bcm2835_sdhost_dumpcmd(host, host->mrq->sbc, "sbc");
-+ bcm2835_sdhost_dumpcmd(host, host->mrq->cmd, "cmd");
-+ if (host->mrq->data)
-+ pr_err("%s: data blocks %x blksz %x - err %d\n",
-+ mmc_hostname(host->mmc),
-+ host->mrq->data->blocks,
-+ host->mrq->data->blksz,
-+ host->mrq->data->error);
-+ bcm2835_sdhost_dumpcmd(host, host->mrq->stop, "stop");
-+
-+ pr_info("%s: =========== REGISTER DUMP ===========\n",
-+ mmc_hostname(host->mmc));
-+
-+ pr_info("%s: SDCMD 0x%08x\n",
-+ mmc_hostname(host->mmc),
-+ bcm2835_sdhost_read(host, SDCMD));
-+ pr_info("%s: SDARG 0x%08x\n",
-+ mmc_hostname(host->mmc),
-+ bcm2835_sdhost_read(host, SDARG));
-+ pr_info("%s: SDTOUT 0x%08x\n",
-+ mmc_hostname(host->mmc),
-+ bcm2835_sdhost_read(host, SDTOUT));
-+ pr_info("%s: SDCDIV 0x%08x\n",
-+ mmc_hostname(host->mmc),
-+ bcm2835_sdhost_read(host, SDCDIV));
-+ pr_info("%s: SDRSP0 0x%08x\n",
-+ mmc_hostname(host->mmc),
-+ bcm2835_sdhost_read(host, SDRSP0));
-+ pr_info("%s: SDRSP1 0x%08x\n",
-+ mmc_hostname(host->mmc),
-+ bcm2835_sdhost_read(host, SDRSP1));
-+ pr_info("%s: SDRSP2 0x%08x\n",
-+ mmc_hostname(host->mmc),
-+ bcm2835_sdhost_read(host, SDRSP2));
-+ pr_info("%s: SDRSP3 0x%08x\n",
-+ mmc_hostname(host->mmc),
-+ bcm2835_sdhost_read(host, SDRSP3));
-+ pr_info("%s: SDHSTS 0x%08x\n",
-+ mmc_hostname(host->mmc),
-+ bcm2835_sdhost_read(host, SDHSTS));
-+ pr_info("%s: SDVDD 0x%08x\n",
-+ mmc_hostname(host->mmc),
-+ bcm2835_sdhost_read(host, SDVDD));
-+ pr_info("%s: SDEDM 0x%08x\n",
-+ mmc_hostname(host->mmc),
-+ bcm2835_sdhost_read(host, SDEDM));
-+ pr_info("%s: SDHCFG 0x%08x\n",
-+ mmc_hostname(host->mmc),
-+ bcm2835_sdhost_read(host, SDHCFG));
-+ pr_info("%s: SDHBCT 0x%08x\n",
-+ mmc_hostname(host->mmc),
-+ bcm2835_sdhost_read(host, SDHBCT));
-+ pr_info("%s: SDHBLC 0x%08x\n",
-+ mmc_hostname(host->mmc),
-+ bcm2835_sdhost_read(host, SDHBLC));
-+
-+ pr_info("%s: ===========================================\n",
-+ mmc_hostname(host->mmc));
-+}
-+
-+
-+static void bcm2835_sdhost_set_power(struct bcm2835_host *host, bool on)
-+{
-+ bcm2835_sdhost_write(host, on ? 1 : 0, SDVDD);
-+}
-+
-+
-+static void bcm2835_sdhost_reset_internal(struct bcm2835_host *host)
-+{
-+ u32 temp;
-+
-+ bcm2835_sdhost_set_power(host, false);
-+
-+ bcm2835_sdhost_write(host, 0, SDCMD);
-+ bcm2835_sdhost_write(host, 0, SDARG);
-+ bcm2835_sdhost_write(host, 0xf00000, SDTOUT);
-+ bcm2835_sdhost_write(host, 0, SDCDIV);
-+ bcm2835_sdhost_write(host, 0x7f8, SDHSTS); /* Write 1s to clear */
-+ bcm2835_sdhost_write(host, 0, SDHCFG);
-+ bcm2835_sdhost_write(host, 0, SDHBCT);
-+ bcm2835_sdhost_write(host, 0, SDHBLC);
-+
-+ /* Limit fifo usage due to silicon bug */
-+ temp = bcm2835_sdhost_read(host, SDEDM);
-+ temp &= ~((SDEDM_THRESHOLD_MASK<<SDEDM_READ_THRESHOLD_SHIFT) |
-+ (SDEDM_THRESHOLD_MASK<<SDEDM_WRITE_THRESHOLD_SHIFT));
-+ temp |= (SAFE_READ_THRESHOLD << SDEDM_READ_THRESHOLD_SHIFT) |
-+ (SAFE_WRITE_THRESHOLD << SDEDM_WRITE_THRESHOLD_SHIFT);
-+ bcm2835_sdhost_write(host, temp, SDEDM);
-+ mdelay(10);
-+ bcm2835_sdhost_set_power(host, true);
-+ mdelay(10);
-+ host->clock = 0;
-+ bcm2835_sdhost_write(host, host->hcfg, SDHCFG);
-+ bcm2835_sdhost_write(host, host->cdiv, SDCDIV);
-+ mmiowb();
-+}
-+
-+
-+static void bcm2835_sdhost_reset(struct mmc_host *mmc)
-+{
-+ struct bcm2835_host *host = mmc_priv(mmc);
-+ unsigned long flags;
-+ if (host->debug)
-+ pr_info("%s: reset\n", mmc_hostname(mmc));
-+ spin_lock_irqsave(&host->lock, flags);
-+
-+ bcm2835_sdhost_reset_internal(host);
-+
-+ spin_unlock_irqrestore(&host->lock, flags);
-+}
-+
-+static void bcm2835_sdhost_set_ios(struct mmc_host *mmc, struct mmc_ios *ios);
-+
-+static void bcm2835_sdhost_init(struct bcm2835_host *host, int soft)
-+{
-+ pr_debug("bcm2835_sdhost_init(%d)\n", soft);
-+
-+ /* Set interrupt enables */
-+ host->hcfg = SDHCFG_BUSY_IRPT_EN;
-+
-+ bcm2835_sdhost_reset_internal(host);
-+
-+ if (soft) {
-+ /* force clock reconfiguration */
-+ host->clock = 0;
-+ bcm2835_sdhost_set_ios(host->mmc, &host->mmc->ios);
-+ }
-+}
-+
-+static bool bcm2835_sdhost_is_write_complete(struct bcm2835_host *host)
-+{
-+ bool write_complete = ((bcm2835_sdhost_read(host, SDEDM) & 0xf) == 1);
-+
-+ if (!write_complete) {
-+ /* Request an IRQ for the last block */
-+ host->hcfg |= SDHCFG_BLOCK_IRPT_EN;
-+ bcm2835_sdhost_write(host, host->hcfg, SDHCFG);
-+ if ((bcm2835_sdhost_read(host, SDEDM) & 0xf) == 1) {
-+ /* The write has now completed. Disable the interrupt
-+ and clear the status flag */
-+ host->hcfg &= ~SDHCFG_BLOCK_IRPT_EN;
-+ bcm2835_sdhost_write(host, host->hcfg, SDHCFG);
-+ bcm2835_sdhost_write(host, SDHSTS_BLOCK_IRPT, SDHSTS);
-+ write_complete = true;
-+ }
-+ }
-+
-+ return write_complete;
-+}
-+
-+static void bcm2835_sdhost_wait_write_complete(struct bcm2835_host *host)
-+{
-+ int timediff;
-+#ifdef DEBUG
-+ static struct timeval start_time;
-+ static int max_stall_time = 0;
-+ static int total_stall_time = 0;
-+ struct timeval before, after;
-+
-+ do_gettimeofday(&before);
-+ if (max_stall_time == 0)
-+ start_time = before;
-+#endif
-+
-+ timediff = 0;
-+
-+ while (1) {
-+ u32 edm = bcm2835_sdhost_read(host, SDEDM);
-+ if ((edm & 0xf) == 1)
-+ break;
-+ timediff++;
-+ if (timediff > 5000000) {
-+#ifdef DEBUG
-+ do_gettimeofday(&after);
-+ timediff = (after.tv_sec - before.tv_sec)*1000000 +
-+ (after.tv_usec - before.tv_usec);
-+
-+ pr_err(" wait_write_complete - still waiting after %dus\n",
-+ timediff);
-+#else
-+ pr_err(" wait_write_complete - still waiting after %d retries\n",
-+ timediff);
-+#endif
-+ bcm2835_sdhost_dumpregs(host);
-+ host->data->error = -ETIMEDOUT;
-+ return;
-+ }
-+ }
-+
-+#ifdef DEBUG
-+ do_gettimeofday(&after);
-+ timediff = (after.tv_sec - before.tv_sec)*1000000 + (after.tv_usec - before.tv_usec);
-+
-+ total_stall_time += timediff;
-+ if (timediff > max_stall_time)
-+ max_stall_time = timediff;
-+
-+ if ((after.tv_sec - start_time.tv_sec) > 10) {
-+ pr_debug(" wait_write_complete - max wait %dus, total %dus\n",
-+ max_stall_time, total_stall_time);
-+ start_time = after;
-+ max_stall_time = 0;
-+ total_stall_time = 0;
-+ }
-+#endif
-+}
-+
-+static void bcm2835_sdhost_finish_data(struct bcm2835_host *host);
-+
-+static void bcm2835_sdhost_dma_complete(void *param)
-+{
-+ struct bcm2835_host *host = param;
-+ struct dma_chan *dma_chan;
-+ unsigned long flags;
-+ u32 dir_data;
-+
-+ spin_lock_irqsave(&host->lock, flags);
-+
-+ if (host->data) {
-+ bool write_complete;
-+ if (USE_BLOCK_IRQ)
-+ write_complete = bcm2835_sdhost_is_write_complete(host);
-+ else {
-+ bcm2835_sdhost_wait_write_complete(host);
-+ write_complete = true;
-+ }
-+ pr_debug("dma_complete() - write_complete=%d\n",
-+ write_complete);
-+
-+ if (write_complete || (host->data->flags & MMC_DATA_READ))
-+ {
-+ if (write_complete) {
-+ dma_chan = host->dma_chan_tx;
-+ dir_data = DMA_TO_DEVICE;
-+ } else {
-+ dma_chan = host->dma_chan_rx;
-+ dir_data = DMA_FROM_DEVICE;
-+ }
-+
-+ dma_unmap_sg(dma_chan->device->dev,
-+ host->data->sg, host->data->sg_len,
-+ dir_data);
-+
-+ bcm2835_sdhost_finish_data(host);
-+ }
-+ }
-+
-+ spin_unlock_irqrestore(&host->lock, flags);
-+}
-+
-+static bool data_transfer_wait(struct bcm2835_host *host)
-+{
-+ unsigned long timeout = 1000000;
-+ while (timeout)
-+ {
-+ u32 sdhsts = bcm2835_sdhost_read(host, SDHSTS);
-+ if (sdhsts & SDHSTS_DATA_FLAG) {
-+ bcm2835_sdhost_write(host, SDHSTS_DATA_FLAG, SDHSTS);
-+ break;
-+ }
-+ timeout--;
-+ }
-+ if (timeout == 0) {
-+ pr_err("%s: Data %s timeout\n",
-+ mmc_hostname(host->mmc),
-+ (host->data->flags & MMC_DATA_READ) ? "read" : "write");
-+ bcm2835_sdhost_dumpregs(host);
-+ host->data->error = -ETIMEDOUT;
-+ return false;
-+ }
-+ return true;
-+}
-+
-+static void bcm2835_sdhost_read_block_pio(struct bcm2835_host *host)
-+{
-+ unsigned long flags;
-+ size_t blksize, len;
-+ u32 *buf;
-+
-+ blksize = host->data->blksz;
-+
-+ local_irq_save(flags);
-+
-+ while (blksize) {
-+ if (!sg_miter_next(&host->sg_miter))
-+ BUG();
-+
-+ len = min(host->sg_miter.length, blksize);
-+ BUG_ON(len % 4);
-+
-+ blksize -= len;
-+ host->sg_miter.consumed = len;
-+
-+ buf = (u32 *)host->sg_miter.addr;
-+
-+ while (len) {
-+ if (!data_transfer_wait(host))
-+ break;
-+
-+ *(buf++) = bcm2835_sdhost_read(host, SDDATA);
-+ len -= 4;
-+ }
-+
-+ if (host->data->error)
-+ break;
-+ }
-+
-+ sg_miter_stop(&host->sg_miter);
-+
-+ local_irq_restore(flags);
-+}
-+
-+static void bcm2835_sdhost_write_block_pio(struct bcm2835_host *host)
-+{
-+ unsigned long flags;
-+ size_t blksize, len;
-+ u32 *buf;
-+
-+ blksize = host->data->blksz;
-+
-+ local_irq_save(flags);
-+
-+ while (blksize) {
-+ if (!sg_miter_next(&host->sg_miter))
-+ BUG();
-+
-+ len = min(host->sg_miter.length, blksize);
-+ BUG_ON(len % 4);
-+
-+ blksize -= len;
-+ host->sg_miter.consumed = len;
-+
-+ buf = host->sg_miter.addr;
-+
-+ while (len) {
-+ if (!data_transfer_wait(host))
-+ break;
-+
-+ bcm2835_sdhost_write(host, *(buf++), SDDATA);
-+ len -= 4;
-+ }
-+
-+ if (host->data->error)
-+ break;
-+ }
-+
-+ sg_miter_stop(&host->sg_miter);
-+
-+ local_irq_restore(flags);
-+}
-+
-+
-+static void bcm2835_sdhost_transfer_pio(struct bcm2835_host *host)
-+{
-+ u32 sdhsts;
-+ bool is_read;
-+ BUG_ON(!host->data);
-+
-+ is_read = (host->data->flags & MMC_DATA_READ) != 0;
-+ if (is_read)
-+ bcm2835_sdhost_read_block_pio(host);
-+ else
-+ bcm2835_sdhost_write_block_pio(host);
-+
-+ sdhsts = bcm2835_sdhost_read(host, SDHSTS);
-+ if (sdhsts & (SDHSTS_CRC16_ERROR |
-+ SDHSTS_CRC7_ERROR |
-+ SDHSTS_FIFO_ERROR)) {
-+ pr_err("%s: %s transfer error - HSTS %x\n",
-+ mmc_hostname(host->mmc),
-+ is_read ? "read" : "write",
-+ sdhsts);
-+ host->data->error = -EILSEQ;
-+ } else if ((sdhsts & (SDHSTS_CMD_TIME_OUT |
-+ SDHSTS_REW_TIME_OUT))) {
-+ pr_err("%s: %s timeout error - HSTS %x\n",
-+ mmc_hostname(host->mmc),
-+ is_read ? "read" : "write",
-+ sdhsts);
-+ host->data->error = -ETIMEDOUT;
-+ } else if (!is_read && !host->data->error) {
-+ /* Start a timer in case a transfer error occurs because
-+ there is no error interrupt */
-+ mod_timer(&host->pio_timer, jiffies + host->pio_timeout);
-+ }
-+}
-+
-+
-+static void bcm2835_sdhost_transfer_dma(struct bcm2835_host *host)
-+{
-+ u32 len, dir_data, dir_slave;
-+ struct dma_async_tx_descriptor *desc = NULL;
-+ struct dma_chan *dma_chan;
-+
-+ pr_debug("bcm2835_sdhost_transfer_dma()\n");
-+
-+ WARN_ON(!host->data);
-+
-+ if (!host->data)
-+ return;
-+
-+ if (host->data->flags & MMC_DATA_READ) {
-+ dma_chan = host->dma_chan_rx;
-+ dir_data = DMA_FROM_DEVICE;
-+ dir_slave = DMA_DEV_TO_MEM;
-+ } else {
-+ dma_chan = host->dma_chan_tx;
-+ dir_data = DMA_TO_DEVICE;
-+ dir_slave = DMA_MEM_TO_DEV;
-+ }
-+
-+ BUG_ON(!dma_chan->device);
-+ BUG_ON(!dma_chan->device->dev);
-+ BUG_ON(!host->data->sg);
-+
-+ len = dma_map_sg(dma_chan->device->dev, host->data->sg,
-+ host->data->sg_len, dir_data);
-+ if (len > 0) {
-+ desc = dmaengine_prep_slave_sg(dma_chan, host->data->sg,
-+ len, dir_slave,
-+ DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
-+ } else {
-+ dev_err(mmc_dev(host->mmc), "dma_map_sg returned zero length\n");
-+ }
-+ if (desc) {
-+ desc->callback = bcm2835_sdhost_dma_complete;
-+ desc->callback_param = host;
-+ dmaengine_submit(desc);
-+ dma_async_issue_pending(dma_chan);
-+ }
-+
-+}
-+
-+
-+static void bcm2835_sdhost_set_transfer_irqs(struct bcm2835_host *host)
-+{
-+ u32 all_irqs = SDHCFG_DATA_IRPT_EN | SDHCFG_BLOCK_IRPT_EN |
-+ SDHCFG_BUSY_IRPT_EN;
-+ if (host->use_dma)
-+ host->hcfg = (host->hcfg & ~all_irqs) |
-+ SDHCFG_BUSY_IRPT_EN;
-+ else
-+ host->hcfg = (host->hcfg & ~all_irqs) |
-+ SDHCFG_DATA_IRPT_EN |
-+ SDHCFG_BUSY_IRPT_EN;
-+
-+ bcm2835_sdhost_write(host, host->hcfg, SDHCFG);
-+}
-+
-+
-+static void bcm2835_sdhost_prepare_data(struct bcm2835_host *host, struct mmc_command *cmd)
-+{
-+ struct mmc_data *data = cmd->data;
-+
-+ WARN_ON(host->data);
-+
-+ if (!data)
-+ return;
-+
-+ /* Sanity checks */
-+ BUG_ON(data->blksz * data->blocks > 524288);
-+ BUG_ON(data->blksz > host->mmc->max_blk_size);
-+ BUG_ON(data->blocks > 65535);
-+
-+ host->data = data;
-+ host->data_complete = 0;
-+ host->flush_fifo = 0;
-+ host->data->bytes_xfered = 0;
-+
-+ host->use_dma = host->have_dma && (data->blocks > host->pio_limit);
-+ if (!host->use_dma) {
-+ int flags;
-+
-+ flags = SG_MITER_ATOMIC;
-+ if (data->flags & MMC_DATA_READ)
-+ flags |= SG_MITER_TO_SG;
-+ else
-+ flags |= SG_MITER_FROM_SG;
-+ sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags);
-+ host->blocks = data->blocks;
-+ }
-+
-+ bcm2835_sdhost_set_transfer_irqs(host);
-+
-+ bcm2835_sdhost_write(host, data->blksz, SDHBCT);
-+ bcm2835_sdhost_write(host, host->use_dma ? data->blocks : 0, SDHBLC);
-+
-+ BUG_ON(!host->data);
-+}
-+
-+
-+void bcm2835_sdhost_send_command(struct bcm2835_host *host, struct mmc_command *cmd)
-+{
-+ u32 sdcmd, sdhsts;
-+ unsigned long timeout;
-+ int delay;
-+
-+ WARN_ON(host->cmd);
-+
-+ if (cmd->data)
-+ pr_debug("%s: send_command %d 0x%x "
-+ "(flags 0x%x) - %s %d*%d\n",
-+ mmc_hostname(host->mmc),
-+ cmd->opcode, cmd->arg, cmd->flags,
-+ (cmd->data->flags & MMC_DATA_READ) ?
-+ "read" : "write", cmd->data->blocks,
-+ cmd->data->blksz);
-+ else
-+ pr_debug("%s: send_command %d 0x%x (flags 0x%x)\n",
-+ mmc_hostname(host->mmc),
-+ cmd->opcode, cmd->arg, cmd->flags);
-+
-+ /* Wait max 100 ms */
-+ timeout = 10000;
-+
-+ while (bcm2835_sdhost_read(host, SDCMD) & SDCMD_NEW_FLAG) {
-+ if (timeout == 0) {
-+ pr_err("%s: previous command never completed.\n",
-+ mmc_hostname(host->mmc));
-+ bcm2835_sdhost_dumpregs(host);
-+ cmd->error = -EIO;
-+ tasklet_schedule(&host->finish_tasklet);
-+ return;
-+ }
-+ timeout--;
-+ udelay(10);
-+ }
-+
-+ delay = (10000 - timeout)/100;
-+ if (delay > host->max_delay) {
-+ host->max_delay = delay;
-+ pr_warning("%s: controller hung for %d ms\n",
-+ mmc_hostname(host->mmc),
-+ host->max_delay);
-+ }
-+
-+ timeout = jiffies;
-+ if (!cmd->data && cmd->busy_timeout > 9000)
-+ timeout += DIV_ROUND_UP(cmd->busy_timeout, 1000) * HZ + HZ;
-+ else
-+ timeout += 10 * HZ;
-+ mod_timer(&host->timer, timeout);
-+
-+ host->cmd = cmd;
-+
-+ /* Clear any error flags */
-+ sdhsts = bcm2835_sdhost_read(host, SDHSTS);
-+ if (sdhsts & SDHSTS_ERROR_MASK)
-+ bcm2835_sdhost_write(host, sdhsts, SDHSTS);
-+
-+ bcm2835_sdhost_prepare_data(host, cmd);
-+
-+ bcm2835_sdhost_write(host, cmd->arg, SDARG);
-+
-+ if ((cmd->flags & MMC_RSP_136) && (cmd->flags & MMC_RSP_BUSY)) {
-+ pr_err("%s: unsupported response type!\n",
-+ mmc_hostname(host->mmc));
-+ cmd->error = -EINVAL;
-+ tasklet_schedule(&host->finish_tasklet);
-+ return;
-+ }
-+
-+ sdcmd = cmd->opcode & SDCMD_CMD_MASK;
-+
-+ if (!(cmd->flags & MMC_RSP_PRESENT))
-+ sdcmd |= SDCMD_NO_RESPONSE;
-+ else {
-+ if (cmd->flags & MMC_RSP_136)
-+ sdcmd |= SDCMD_LONG_RESPONSE;
-+ if (cmd->flags & MMC_RSP_BUSY) {
-+ sdcmd |= SDCMD_BUSYWAIT;
-+ host->use_busy = 1;
-+ }
-+ }
-+
-+ if (cmd->data) {
-+ if (host->delay_after_stop) {
-+ struct timeval now;
-+ int time_since_stop;
-+ do_gettimeofday(&now);
-+ time_since_stop = (now.tv_sec - host->stop_time.tv_sec);
-+ if (time_since_stop < 2) {
-+ /* Possibly less than one second */
-+ time_since_stop = time_since_stop * 1000000 +
-+ (now.tv_usec - host->stop_time.tv_usec);
-+ if (time_since_stop < host->delay_after_stop)
-+ udelay(host->delay_after_stop -
-+ time_since_stop);
-+ }
-+ }
-+
-+ if (cmd->data->flags & MMC_DATA_WRITE)
-+ sdcmd |= SDCMD_WRITE_CMD;
-+ if (cmd->data->flags & MMC_DATA_READ)
-+ sdcmd |= SDCMD_READ_CMD;
-+ }
-+
-+ bcm2835_sdhost_write(host, sdcmd | SDCMD_NEW_FLAG, SDCMD);
-+}
-+
-+
-+static void bcm2835_sdhost_finish_command(struct bcm2835_host *host);
-+static void bcm2835_sdhost_transfer_complete(struct bcm2835_host *host);
-+
-+static void bcm2835_sdhost_finish_data(struct bcm2835_host *host)
-+{
-+ struct mmc_data *data;
-+
-+ data = host->data;
-+ BUG_ON(!data);
-+
-+ pr_debug("finish_data(error %d, stop %d, sbc %d)\n",
-+ data->error, data->stop ? 1 : 0,
-+ host->mrq->sbc ? 1 : 0);
-+
-+ host->hcfg &= ~(SDHCFG_DATA_IRPT_EN | SDHCFG_BLOCK_IRPT_EN);
-+ bcm2835_sdhost_write(host, host->hcfg, SDHCFG);
-+
-+ if (data->error) {
-+ data->bytes_xfered = 0;
-+ } else
-+ data->bytes_xfered = data->blksz * data->blocks;
-+
-+ host->data_complete = 1;
-+
-+ if (host->cmd) {
-+ /*
-+ * Data managed to finish before the
-+ * command completed. Make sure we do
-+ * things in the proper order.
-+ */
-+ pr_debug("Finished early - HSTS %x\n",
-+ bcm2835_sdhost_read(host, SDHSTS));
-+ }
-+ else
-+ bcm2835_sdhost_transfer_complete(host);
-+}
-+
-+
-+static void bcm2835_sdhost_transfer_complete(struct bcm2835_host *host)
-+{
-+ struct mmc_data *data;
-+
-+ BUG_ON(host->cmd);
-+ BUG_ON(!host->data);
-+ BUG_ON(!host->data_complete);
-+
-+ data = host->data;
-+ host->data = NULL;
-+
-+ pr_debug("transfer_complete(error %d, stop %d)\n",
-+ data->error, data->stop ? 1 : 0);
-+
-+ /*
-+ * Need to send CMD12 if -
-+ * a) open-ended multiblock transfer (no CMD23)
-+ * b) error in multiblock transfer
-+ */
-+ if (data->stop &&
-+ (data->error ||
-+ !host->mrq->sbc)) {
-+ host->flush_fifo = 1;
-+ bcm2835_sdhost_send_command(host, data->stop);
-+ if (host->delay_after_stop)
-+ do_gettimeofday(&host->stop_time);
-+ if (!host->use_busy)
-+ bcm2835_sdhost_finish_command(host);
-+ } else {
-+ tasklet_schedule(&host->finish_tasklet);
-+ }
-+}
-+
-+static void bcm2835_sdhost_finish_command(struct bcm2835_host *host)
-+{
-+ u32 sdcmd;
-+ unsigned long timeout;
-+#ifdef DEBUG
-+ struct timeval before, after;
-+ int timediff = 0;
-+#endif
-+
-+ pr_debug("finish_command(%x)\n", bcm2835_sdhost_read(host, SDCMD));
-+
-+ BUG_ON(!host->cmd || !host->mrq);
-+
-+#ifdef DEBUG
-+ do_gettimeofday(&before);
-+#endif
-+ /* Wait max 100 ms */
-+ timeout = 10000;
-+ for (sdcmd = bcm2835_sdhost_read(host, SDCMD);
-+ (sdcmd & SDCMD_NEW_FLAG) && timeout;
-+ timeout--) {
-+ if (host->flush_fifo) {
-+ while (bcm2835_sdhost_read(host, SDHSTS) &
-+ SDHSTS_DATA_FLAG)
-+ (void)bcm2835_sdhost_read(host, SDDATA);
-+ }
-+ udelay(10);
-+ sdcmd = bcm2835_sdhost_read(host, SDCMD);
-+ }
-+#ifdef DEBUG
-+ do_gettimeofday(&after);
-+ timediff = (after.tv_sec - before.tv_sec)*1000000 +
-+ (after.tv_usec - before.tv_usec);
-+
-+ pr_debug(" finish_command - waited %dus\n", timediff);
-+#endif
-+
-+ if (timeout == 0) {
-+ pr_err("%s: command never completed.\n",
-+ mmc_hostname(host->mmc));
-+ bcm2835_sdhost_dumpregs(host);
-+ host->cmd->error = -EIO;
-+ tasklet_schedule(&host->finish_tasklet);
-+ return;
-+ }
-+
-+ if (host->flush_fifo) {
-+ for (timeout = 100;
-+ (bcm2835_sdhost_read(host, SDHSTS) & SDHSTS_DATA_FLAG) && timeout;
-+ timeout--) {
-+ (void)bcm2835_sdhost_read(host, SDDATA);
-+ }
-+ host->flush_fifo = 0;
-+ if (timeout == 0) {
-+ pr_err("%s: FIFO never drained.\n",
-+ mmc_hostname(host->mmc));
-+ bcm2835_sdhost_dumpregs(host);
-+ host->cmd->error = -EIO;
-+ tasklet_schedule(&host->finish_tasklet);
-+ return;
-+ }
-+ }
-+
-+ /* Check for errors */
-+ if (sdcmd & SDCMD_FAIL_FLAG)
-+ {
-+ u32 sdhsts = bcm2835_sdhost_read(host, SDHSTS);
-+
-+ if (host->debug)
-+ pr_info("%s: error detected - CMD %x, HSTS %03x, EDM %x\n",
-+ mmc_hostname(host->mmc), sdcmd, sdhsts,
-+ bcm2835_sdhost_read(host, SDEDM));
-+
-+ if ((sdhsts & SDHSTS_CRC7_ERROR) &&
-+ (host->cmd->opcode == 1)) {
-+ if (host->debug)
-+ pr_info("%s: ignoring CRC7 error for CMD1\n",
-+ mmc_hostname(host->mmc));
-+ } else {
-+ if (sdhsts & SDHSTS_CMD_TIME_OUT) {
-+ if (host->debug)
-+ pr_err("%s: command %d timeout\n",
-+ mmc_hostname(host->mmc),
-+ host->cmd->opcode);
-+ host->cmd->error = -ETIMEDOUT;
-+ } else {
-+ pr_err("%s: unexpected command %d error\n",
-+ mmc_hostname(host->mmc),
-+ host->cmd->opcode);
-+ bcm2835_sdhost_dumpregs(host);
-+ host->cmd->error = -EIO;
-+ }
-+ tasklet_schedule(&host->finish_tasklet);
-+ return;
-+ }
-+ }
-+
-+ if (host->cmd->flags & MMC_RSP_PRESENT) {
-+ if (host->cmd->flags & MMC_RSP_136) {
-+ int i;
-+ for (i = 0; i < 4; i++)
-+ host->cmd->resp[3 - i] = bcm2835_sdhost_read(host, SDRSP0 + i*4);
-+ pr_debug("%s: finish_command %08x %08x %08x %08x\n",
-+ mmc_hostname(host->mmc),
-+ host->cmd->resp[0], host->cmd->resp[1], host->cmd->resp[2], host->cmd->resp[3]);
-+ } else {
-+ host->cmd->resp[0] = bcm2835_sdhost_read(host, SDRSP0);
-+ pr_debug("%s: finish_command %08x\n",
-+ mmc_hostname(host->mmc),
-+ host->cmd->resp[0]);
-+ }
-+ }
-+
-+ host->cmd->error = 0;
-+
-+ if (host->cmd == host->mrq->sbc) {
-+ /* Finished CMD23, now send actual command. */
-+ host->cmd = NULL;
-+ bcm2835_sdhost_send_command(host, host->mrq->cmd);
-+
-+ if (host->cmd->data && host->use_dma)
-+ /* DMA transfer starts now, PIO starts after irq */
-+ bcm2835_sdhost_transfer_dma(host);
-+
-+ if (!host->use_busy)
-+ bcm2835_sdhost_finish_command(host);
-+ } else if (host->cmd == host->mrq->stop)
-+ /* Finished CMD12 */
-+ tasklet_schedule(&host->finish_tasklet);
-+ else {
-+ /* Processed actual command. */
-+ host->cmd = NULL;
-+ if (!host->data)
-+ tasklet_schedule(&host->finish_tasklet);
-+ else if (host->data_complete)
-+ bcm2835_sdhost_transfer_complete(host);
-+ }
-+}
-+
-+static void bcm2835_sdhost_timeout(unsigned long data)
-+{
-+ struct bcm2835_host *host;
-+ unsigned long flags;
-+
-+ host = (struct bcm2835_host *)data;
-+
-+ spin_lock_irqsave(&host->lock, flags);
-+
-+ if (host->mrq) {
-+ pr_err("%s: timeout waiting for hardware interrupt.\n",
-+ mmc_hostname(host->mmc));
-+ bcm2835_sdhost_dumpregs(host);
-+
-+ if (host->data) {
-+ host->data->error = -ETIMEDOUT;
-+ bcm2835_sdhost_finish_data(host);
-+ } else {
-+ if (host->cmd)
-+ host->cmd->error = -ETIMEDOUT;
-+ else
-+ host->mrq->cmd->error = -ETIMEDOUT;
-+
-+ pr_debug("timeout_timer tasklet_schedule\n");
-+ tasklet_schedule(&host->finish_tasklet);
-+ }
-+ }
-+
-+ mmiowb();
-+ spin_unlock_irqrestore(&host->lock, flags);
-+}
-+
-+static void bcm2835_sdhost_pio_timeout(unsigned long data)
-+{
-+ struct bcm2835_host *host;
-+ unsigned long flags;
-+
-+ host = (struct bcm2835_host *)data;
-+
-+ spin_lock_irqsave(&host->lock, flags);
-+
-+ if (host->data) {
-+ u32 sdhsts = bcm2835_sdhost_read(host, SDHSTS);
-+
-+ if (sdhsts & SDHSTS_REW_TIME_OUT) {
-+ pr_err("%s: transfer timeout\n",
-+ mmc_hostname(host->mmc));
-+ if (host->debug)
-+ bcm2835_sdhost_dumpregs(host);
-+ } else {
-+ pr_err("%s: unexpected transfer timeout\n",
-+ mmc_hostname(host->mmc));
-+ bcm2835_sdhost_dumpregs(host);
-+ }
-+
-+ bcm2835_sdhost_write(host, SDHSTS_TRANSFER_ERROR_MASK,
-+ SDHSTS);
-+
-+ host->data->error = -ETIMEDOUT;
-+
-+ bcm2835_sdhost_finish_data(host);
-+ }
-+
-+ mmiowb();
-+ spin_unlock_irqrestore(&host->lock, flags);
-+}
-+
-+static void bcm2835_sdhost_enable_sdio_irq_nolock(struct bcm2835_host *host, int enable)
-+{
-+ if (enable)
-+ host->hcfg |= SDHCFG_SDIO_IRPT_EN;
-+ else
-+ host->hcfg &= ~SDHCFG_SDIO_IRPT_EN;
-+ bcm2835_sdhost_write(host, host->hcfg, SDHCFG);
-+ mmiowb();
-+}
-+
-+static void bcm2835_sdhost_enable_sdio_irq(struct mmc_host *mmc, int enable)
-+{
-+ struct bcm2835_host *host = mmc_priv(mmc);
-+ unsigned long flags;
-+
-+ pr_debug("%s: enable_sdio_irq(%d)\n", mmc_hostname(mmc), enable);
-+ spin_lock_irqsave(&host->lock, flags);
-+ bcm2835_sdhost_enable_sdio_irq_nolock(host, enable);
-+ spin_unlock_irqrestore(&host->lock, flags);
-+}
-+
-+static u32 bcm2835_sdhost_busy_irq(struct bcm2835_host *host, u32 intmask)
-+{
-+ const u32 handled = (SDHSTS_REW_TIME_OUT | SDHSTS_CMD_TIME_OUT |
-+ SDHSTS_CRC16_ERROR | SDHSTS_CRC7_ERROR |
-+ SDHSTS_FIFO_ERROR);
-+
-+ if (!host->cmd) {
-+ pr_err("%s: got command busy interrupt 0x%08x even "
-+ "though no command operation was in progress.\n",
-+ mmc_hostname(host->mmc), (unsigned)intmask);
-+ bcm2835_sdhost_dumpregs(host);
-+ return 0;
-+ }
-+
-+ if (!host->use_busy) {
-+ pr_err("%s: got command busy interrupt 0x%08x even "
-+ "though not expecting one.\n",
-+ mmc_hostname(host->mmc), (unsigned)intmask);
-+ bcm2835_sdhost_dumpregs(host);
-+ return 0;
-+ }
-+ host->use_busy = 0;
-+
-+ if (intmask & SDHSTS_ERROR_MASK)
-+ {
-+ pr_err("sdhost_busy_irq: intmask %x, data %p\n", intmask, host->mrq->data);
-+ if (intmask & SDHSTS_CRC7_ERROR)
-+ host->cmd->error = -EILSEQ;
-+ else if (intmask & (SDHSTS_CRC16_ERROR |
-+ SDHSTS_FIFO_ERROR)) {
-+ if (host->mrq->data)
-+ host->mrq->data->error = -EILSEQ;
-+ else
-+ host->cmd->error = -EILSEQ;
-+ } else if (intmask & SDHSTS_REW_TIME_OUT) {
-+ if (host->mrq->data)
-+ host->mrq->data->error = -ETIMEDOUT;
-+ else
-+ host->cmd->error = -ETIMEDOUT;
-+ } else if (intmask & SDHSTS_CMD_TIME_OUT)
-+ host->cmd->error = -ETIMEDOUT;
-+
-+ bcm2835_sdhost_dumpregs(host);
-+ tasklet_schedule(&host->finish_tasklet);
-+ }
-+ else
-+ bcm2835_sdhost_finish_command(host);
-+
-+ return handled;
-+}
-+
-+static u32 bcm2835_sdhost_data_irq(struct bcm2835_host *host, u32 intmask)
-+{
-+ const u32 handled = (SDHSTS_REW_TIME_OUT |
-+ SDHSTS_CRC16_ERROR |
-+ SDHSTS_FIFO_ERROR);
-+
-+ /* There are no dedicated data/space available interrupt
-+ status bits, so it is necessary to use the single shared
-+ data/space available FIFO status bits. It is therefore not
-+ an error to get here when there is no data transfer in
-+ progress. */
-+ if (!host->data)
-+ return 0;
-+
-+ if (intmask & (SDHSTS_CRC16_ERROR |
-+ SDHSTS_FIFO_ERROR |
-+ SDHSTS_REW_TIME_OUT)) {
-+ if (intmask & (SDHSTS_CRC16_ERROR |
-+ SDHSTS_FIFO_ERROR))
-+ host->data->error = -EILSEQ;
-+ else
-+ host->data->error = -ETIMEDOUT;
-+
-+ bcm2835_sdhost_dumpregs(host);
-+ tasklet_schedule(&host->finish_tasklet);
-+ return handled;
-+ }
-+
-+ /* Use the block interrupt for writes after the first block */
-+ if (host->data->flags & MMC_DATA_WRITE) {
-+ host->hcfg &= ~(SDHCFG_DATA_IRPT_EN);
-+ host->hcfg |= SDHCFG_BLOCK_IRPT_EN;
-+ bcm2835_sdhost_write(host, host->hcfg, SDHCFG);
-+ if (host->data->error)
-+ bcm2835_sdhost_finish_data(host);
-+ else
-+ bcm2835_sdhost_transfer_pio(host);
-+ } else {
-+ if (!host->data->error) {
-+ bcm2835_sdhost_transfer_pio(host);
-+ host->blocks--;
-+ }
-+ if ((host->blocks == 0) || host->data->error)
-+ bcm2835_sdhost_finish_data(host);
-+ }
-+
-+ return handled;
-+}
-+
-+static u32 bcm2835_sdhost_block_irq(struct bcm2835_host *host, u32 intmask)
-+{
-+ struct dma_chan *dma_chan;
-+ u32 dir_data;
-+ const u32 handled = (SDHSTS_REW_TIME_OUT |
-+ SDHSTS_CRC16_ERROR |
-+ SDHSTS_FIFO_ERROR);
-+
-+ if (!host->data) {
-+ pr_err("%s: got block interrupt 0x%08x even "
-+ "though no data operation was in progress.\n",
-+ mmc_hostname(host->mmc), (unsigned)intmask);
-+ bcm2835_sdhost_dumpregs(host);
-+ return handled;
-+ }
-+
-+ if (intmask & (SDHSTS_CRC16_ERROR |
-+ SDHSTS_FIFO_ERROR |
-+ SDHSTS_REW_TIME_OUT)) {
-+ if (intmask & (SDHSTS_CRC16_ERROR |
-+ SDHSTS_FIFO_ERROR))
-+ host->data->error = -EILSEQ;
-+ else
-+ host->data->error = -ETIMEDOUT;
-+
-+ if (host->debug)
-+ bcm2835_sdhost_dumpregs(host);
-+ tasklet_schedule(&host->finish_tasklet);
-+ return handled;
-+ }
-+
-+ if (!host->use_dma) {
-+ BUG_ON(!host->blocks);
-+ host->blocks--;
-+ if ((host->blocks == 0) || host->data->error) {
-+ /* Cancel the timer */
-+ del_timer(&host->pio_timer);
-+
-+ bcm2835_sdhost_finish_data(host);
-+ } else {
-+ bcm2835_sdhost_transfer_pio(host);
-+
-+ /* Reset the timer */
-+ mod_timer(&host->pio_timer,
-+ jiffies + host->pio_timeout);
-+ }
-+ } else if (host->data->flags & MMC_DATA_WRITE) {
-+ dma_chan = host->dma_chan_tx;
-+ dir_data = DMA_TO_DEVICE;
-+ dma_unmap_sg(dma_chan->device->dev,
-+ host->data->sg, host->data->sg_len,
-+ dir_data);
-+
-+ bcm2835_sdhost_finish_data(host);
-+ }
-+
-+ return handled;
-+}
-+
-+
-+static irqreturn_t bcm2835_sdhost_irq(int irq, void *dev_id)
-+{
-+ irqreturn_t result = IRQ_NONE;
-+ struct bcm2835_host *host = dev_id;
-+ u32 unexpected = 0, early = 0;
-+ int loops = 0;
-+
-+ spin_lock(&host->lock);
-+
-+ for (loops = 0; loops < 1; loops++) {
-+ u32 intmask, handled;
-+
-+ intmask = bcm2835_sdhost_read(host, SDHSTS);
-+ handled = intmask & (SDHSTS_BUSY_IRPT |
-+ SDHSTS_BLOCK_IRPT |
-+ SDHSTS_SDIO_IRPT |
-+ SDHSTS_DATA_FLAG);
-+ if ((handled == SDHSTS_DATA_FLAG) &&
-+ (loops == 0) && !host->data) {
-+ pr_err("%s: sdhost_irq data interrupt 0x%08x even "
-+ "though no data operation was in progress.\n",
-+ mmc_hostname(host->mmc),
-+ (unsigned)intmask);
-+
-+ bcm2835_sdhost_dumpregs(host);
-+ }
-+
-+ if (!handled)
-+ break;
-+
-+ if (loops)
-+ early |= handled;
-+
-+ result = IRQ_HANDLED;
-+
-+ /* Clear all interrupts and notifications */
-+ bcm2835_sdhost_write(host, intmask, SDHSTS);
-+
-+ if (intmask & SDHSTS_BUSY_IRPT)
-+ handled |= bcm2835_sdhost_busy_irq(host, intmask);
-+
-+ /* There is no true data interrupt status bit, so it is
-+ necessary to qualify the data flag with the interrupt
-+ enable bit */
-+ if ((intmask & SDHSTS_DATA_FLAG) &&
-+ (host->hcfg & SDHCFG_DATA_IRPT_EN))
-+ handled |= bcm2835_sdhost_data_irq(host, intmask);
-+
-+ if (intmask & SDHSTS_BLOCK_IRPT)
-+ handled |= bcm2835_sdhost_block_irq(host, intmask);
-+
-+ if (intmask & SDHSTS_SDIO_IRPT) {
-+ bcm2835_sdhost_enable_sdio_irq_nolock(host, false);
-+ host->thread_isr |= SDHSTS_SDIO_IRPT;
-+ result = IRQ_WAKE_THREAD;
-+ }
-+
-+ unexpected |= (intmask & ~handled);
-+ }
-+
-+ mmiowb();
-+
-+ spin_unlock(&host->lock);
-+
-+ if (early)
-+ pr_debug("%s: early %x (loops %d)\n",
-+ mmc_hostname(host->mmc), early, loops);
-+
-+ if (unexpected) {
-+ pr_err("%s: unexpected interrupt 0x%08x.\n",
-+ mmc_hostname(host->mmc), unexpected);
-+ bcm2835_sdhost_dumpregs(host);
-+ }
-+
-+ return result;
-+}
-+
-+static irqreturn_t bcm2835_sdhost_thread_irq(int irq, void *dev_id)
-+{
-+ struct bcm2835_host *host = dev_id;
-+ unsigned long flags;
-+ u32 isr;
-+
-+ spin_lock_irqsave(&host->lock, flags);
-+ isr = host->thread_isr;
-+ host->thread_isr = 0;
-+ spin_unlock_irqrestore(&host->lock, flags);
-+
-+ if (isr & SDHSTS_SDIO_IRPT) {
-+ sdio_run_irqs(host->mmc);
-+
-+/* Is this necessary? Why re-enable an interrupt which is enabled?
-+ spin_lock_irqsave(&host->lock, flags);
-+ if (host->flags & SDHSTS_SDIO_IRPT_ENABLED)
-+ bcm2835_sdhost_enable_sdio_irq_nolock(host, true);
-+ spin_unlock_irqrestore(&host->lock, flags);
-+*/
-+ }
-+
-+ return isr ? IRQ_HANDLED : IRQ_NONE;
-+}
-+
-+
-+
-+void bcm2835_sdhost_set_clock(struct bcm2835_host *host, unsigned int clock)
-+{
-+ int div = 0; /* Initialized for compiler warning */
-+ unsigned int input_clock = clock;
-+
-+ if (host->debug)
-+ pr_info("%s: set_clock(%d)\n", mmc_hostname(host->mmc), clock);
-+
-+ if ((host->overclock_50 > 50) &&
-+ (clock == 50*MHZ)) {
-+ clock = host->overclock_50 * MHZ + (MHZ - 1);
-+ }
-+
-+ /* The SDCDIV register has 11 bits, and holds (div - 2).
-+ But in data mode the max is 50MHz wihout a minimum, and only the
-+ bottom 3 bits are used. Since the switch over is automatic (unless
-+ we have marked the card as slow...), chosen values have to make
-+ sense in both modes.
-+ Ident mode must be 100-400KHz, so can range check the requested
-+ clock. CMD15 must be used to return to data mode, so this can be
-+ monitored.
-+
-+ clock 250MHz -> 0->125MHz, 1->83.3MHz, 2->62.5MHz, 3->50.0MHz
-+ 4->41.7MHz, 5->35.7MHz, 6->31.3MHz, 7->27.8MHz
-+
-+ 623->400KHz/27.8MHz
-+ reset value (507)->491159/50MHz
-+
-+ BUT, the 3-bit clock divisor in data mode is too small if the
-+ core clock is higher than 250MHz, so instead use the SLOW_CARD
-+ configuration bit to force the use of the ident clock divisor
-+ at all times.
-+ */
-+
-+ host->mmc->actual_clock = 0;
-+
-+ if (clock < 100000) {
-+ /* Can't stop the clock, but make it as slow as possible
-+ * to show willing
-+ */
-+ host->cdiv = SDCDIV_MAX_CDIV;
-+ bcm2835_sdhost_write(host, host->cdiv, SDCDIV);
-+ return;
-+ }
-+
-+ div = host->max_clk / clock;
-+ if (div < 2)
-+ div = 2;
-+ if ((host->max_clk / div) > clock)
-+ div++;
-+ div -= 2;
-+
-+ if (div > SDCDIV_MAX_CDIV)
-+ div = SDCDIV_MAX_CDIV;
-+
-+ clock = host->max_clk / (div + 2);
-+ host->mmc->actual_clock = clock;
-+
-+ if (clock > input_clock) {
-+ /* Save the closest value, to make it easier
-+ to reduce in the event of error */
-+ host->overclock_50 = (clock/MHZ);
-+
-+ if (clock != host->overclock) {
-+ pr_warn("%s: overclocking to %dHz\n",
-+ mmc_hostname(host->mmc), clock);
-+ host->overclock = clock;
-+ }
-+ }
-+ else if (host->overclock)
-+ {
-+ host->overclock = 0;
-+ if (clock == 50 * MHZ)
-+ pr_warn("%s: cancelling overclock\n",
-+ mmc_hostname(host->mmc));
-+ }
-+
-+ host->cdiv = div;
-+ bcm2835_sdhost_write(host, host->cdiv, SDCDIV);
-+
-+ /* Set the timeout to 500ms */
-+ bcm2835_sdhost_write(host, host->mmc->actual_clock/2, SDTOUT);
-+
-+ if (host->debug)
-+ pr_info("%s: clock=%d -> max_clk=%d, cdiv=%x (actual clock %d)\n",
-+ mmc_hostname(host->mmc), input_clock,
-+ host->max_clk, host->cdiv, host->mmc->actual_clock);
-+}
-+
-+static void bcm2835_sdhost_request(struct mmc_host *mmc, struct mmc_request *mrq)
-+{
-+ struct bcm2835_host *host;
-+ unsigned long flags;
-+
-+ host = mmc_priv(mmc);
-+
-+ if (host->debug) {
-+ struct mmc_command *cmd = mrq->cmd;
-+ BUG_ON(!cmd);
-+ if (cmd->data)
-+ pr_info("%s: cmd %d 0x%x (flags 0x%x) - %s %d*%d\n",
-+ mmc_hostname(mmc),
-+ cmd->opcode, cmd->arg, cmd->flags,
-+ (cmd->data->flags & MMC_DATA_READ) ?
-+ "read" : "write", cmd->data->blocks,
-+ cmd->data->blksz);
-+ else
-+ pr_info("%s: cmd %d 0x%x (flags 0x%x)\n",
-+ mmc_hostname(mmc),
-+ cmd->opcode, cmd->arg, cmd->flags);
-+ }
-+
-+ /* Reset the error statuses in case this is a retry */
-+ if (mrq->cmd)
-+ mrq->cmd->error = 0;
-+ if (mrq->data)
-+ mrq->data->error = 0;
-+ if (mrq->stop)
-+ mrq->stop->error = 0;
-+
-+ if (mrq->data && !is_power_of_2(mrq->data->blksz)) {
-+ pr_err("%s: unsupported block size (%d bytes)\n",
-+ mmc_hostname(mmc), mrq->data->blksz);
-+ mrq->cmd->error = -EINVAL;
-+ mmc_request_done(mmc, mrq);
-+ return;
-+ }
-+
-+ spin_lock_irqsave(&host->lock, flags);
-+
-+ WARN_ON(host->mrq != NULL);
-+
-+ host->mrq = mrq;
-+
-+ if (mrq->sbc)
-+ bcm2835_sdhost_send_command(host, mrq->sbc);
-+ else
-+ bcm2835_sdhost_send_command(host, mrq->cmd);
-+
-+ mmiowb();
-+ spin_unlock_irqrestore(&host->lock, flags);
-+
-+ if (!mrq->sbc && mrq->cmd->data && host->use_dma)
-+ /* DMA transfer starts now, PIO starts after irq */
-+ bcm2835_sdhost_transfer_dma(host);
-+
-+ if (!host->use_busy)
-+ bcm2835_sdhost_finish_command(host);
-+}
-+
-+
-+static void bcm2835_sdhost_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
-+{
-+
-+ struct bcm2835_host *host = mmc_priv(mmc);
-+ unsigned long flags;
-+
-+ if (host->debug)
-+ pr_info("%s: ios clock %d, pwr %d, bus_width %d, "
-+ "timing %d, vdd %d, drv_type %d\n",
-+ mmc_hostname(mmc),
-+ ios->clock, ios->power_mode, ios->bus_width,
-+ ios->timing, ios->signal_voltage, ios->drv_type);
-+
-+ spin_lock_irqsave(&host->lock, flags);
-+
-+ if (!ios->clock || ios->clock != host->clock) {
-+ bcm2835_sdhost_set_clock(host, ios->clock);
-+ host->clock = ios->clock;
-+ }
-+
-+ /* set bus width */
-+ host->hcfg &= ~SDHCFG_WIDE_EXT_BUS;
-+ if (ios->bus_width == MMC_BUS_WIDTH_4)
-+ host->hcfg |= SDHCFG_WIDE_EXT_BUS;
-+
-+ host->hcfg |= SDHCFG_WIDE_INT_BUS;
-+
-+ /* Disable clever clock switching, to cope with fast core clocks */
-+ host->hcfg |= SDHCFG_SLOW_CARD;
-+
-+ bcm2835_sdhost_write(host, host->hcfg, SDHCFG);
-+
-+ mmiowb();
-+
-+ spin_unlock_irqrestore(&host->lock, flags);
-+}
-+
-+static int bcm2835_sdhost_multi_io_quirk(struct mmc_card *card,
-+ unsigned int direction,
-+ u32 blk_pos, int blk_size)
-+{
-+ /* There is a bug in the host controller hardware that makes
-+ reading the final sector of the card as part of a multiple read
-+ problematic. Detect that case and shorten the read accordingly.
-+ */
-+ /* csd.capacity is in weird units - convert to sectors */
-+ u32 card_sectors = (card->csd.capacity << (card->csd.read_blkbits - 9));
-+
-+ if ((direction == MMC_DATA_READ) &&
-+ ((blk_pos + blk_size) == card_sectors))
-+ blk_size--;
-+
-+ return blk_size;
-+}
-+
-+
-+static struct mmc_host_ops bcm2835_sdhost_ops = {
-+ .request = bcm2835_sdhost_request,
-+ .set_ios = bcm2835_sdhost_set_ios,
-+ .enable_sdio_irq = bcm2835_sdhost_enable_sdio_irq,
-+ .hw_reset = bcm2835_sdhost_reset,
-+ .multi_io_quirk = bcm2835_sdhost_multi_io_quirk,
-+};
-+
-+
-+static void bcm2835_sdhost_tasklet_finish(unsigned long param)
-+{
-+ struct bcm2835_host *host;
-+ unsigned long flags;
-+ struct mmc_request *mrq;
-+
-+ host = (struct bcm2835_host *)param;
-+
-+ spin_lock_irqsave(&host->lock, flags);
-+
-+ /*
-+ * If this tasklet gets rescheduled while running, it will
-+ * be run again afterwards but without any active request.
-+ */
-+ if (!host->mrq) {
-+ spin_unlock_irqrestore(&host->lock, flags);
-+ return;
-+ }
-+
-+ del_timer(&host->timer);
-+
-+ mrq = host->mrq;
-+
-+ /* Drop the overclock after any data corruption, or after any
-+ error overclocked */
-+ if (host->overclock) {
-+ if ((mrq->cmd && mrq->cmd->error) ||
-+ (mrq->data && mrq->data->error) ||
-+ (mrq->stop && mrq->stop->error)) {
-+ host->overclock_50--;
-+ pr_warn("%s: reducing overclock due to errors\n",
-+ mmc_hostname(host->mmc));
-+ bcm2835_sdhost_set_clock(host,50*MHZ);
-+ mrq->cmd->error = -EILSEQ;
-+ mrq->cmd->retries = 1;
-+ }
-+ }
-+
-+ host->mrq = NULL;
-+ host->cmd = NULL;
-+ host->data = NULL;
-+
-+ mmiowb();
-+
-+ spin_unlock_irqrestore(&host->lock, flags);
-+ mmc_request_done(host->mmc, mrq);
-+}
-+
-+
-+
-+int bcm2835_sdhost_add_host(struct bcm2835_host *host)
-+{
-+ struct mmc_host *mmc;
-+ struct dma_slave_config cfg;
-+ char pio_limit_string[20];
-+ int ret;
-+
-+ mmc = host->mmc;
-+
-+ bcm2835_sdhost_reset_internal(host);
-+
-+ mmc->f_max = host->max_clk;
-+ mmc->f_min = host->max_clk / SDCDIV_MAX_CDIV;
-+
-+ mmc->max_busy_timeout = (~(unsigned int)0)/(mmc->f_max/1000);
-+
-+ pr_debug("f_max %d, f_min %d, max_busy_timeout %d\n",
-+ mmc->f_max, mmc->f_min, mmc->max_busy_timeout);
-+
-+ /* host controller capabilities */
-+ mmc->caps |= /* MMC_CAP_SDIO_IRQ |*/ MMC_CAP_4_BIT_DATA |
-+ MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED |
-+ MMC_CAP_NEEDS_POLL | MMC_CAP_HW_RESET | MMC_CAP_ERASE |
-+ (ALLOW_CMD23 * MMC_CAP_CMD23);
-+
-+ spin_lock_init(&host->lock);
-+
-+ if (host->allow_dma) {
-+ if (IS_ERR_OR_NULL(host->dma_chan_tx) ||
-+ IS_ERR_OR_NULL(host->dma_chan_rx)) {
-+ pr_err("%s: unable to initialise DMA channels. "
-+ "Falling back to PIO\n",
-+ mmc_hostname(mmc));
-+ host->have_dma = false;
-+ } else {
-+ host->have_dma = true;
-+
-+ cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
-+ cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
-+ cfg.slave_id = 13; /* DREQ channel */
-+
-+ cfg.direction = DMA_MEM_TO_DEV;
-+ cfg.src_addr = 0;
-+ cfg.dst_addr = host->bus_addr + SDDATA;
-+ ret = dmaengine_slave_config(host->dma_chan_tx, &cfg);
-+
-+ cfg.direction = DMA_DEV_TO_MEM;
-+ cfg.src_addr = host->bus_addr + SDDATA;
-+ cfg.dst_addr = 0;
-+ ret = dmaengine_slave_config(host->dma_chan_rx, &cfg);
-+ }
-+ } else {
-+ host->have_dma = false;
-+ }
-+
-+ mmc->max_segs = 128;
-+ mmc->max_req_size = 524288;
-+ mmc->max_seg_size = mmc->max_req_size;
-+ mmc->max_blk_size = 512;
-+ mmc->max_blk_count = 65535;
-+
-+ /* report supported voltage ranges */
-+ mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
-+
-+ tasklet_init(&host->finish_tasklet,
-+ bcm2835_sdhost_tasklet_finish, (unsigned long)host);
-+
-+ setup_timer(&host->timer, bcm2835_sdhost_timeout,
-+ (unsigned long)host);
-+
-+ setup_timer(&host->pio_timer, bcm2835_sdhost_pio_timeout,
-+ (unsigned long)host);
-+
-+ bcm2835_sdhost_init(host, 0);
-+ ret = request_threaded_irq(host->irq, bcm2835_sdhost_irq,
-+ bcm2835_sdhost_thread_irq,
-+ IRQF_SHARED, mmc_hostname(mmc), host);
-+ if (ret) {
-+ pr_err("%s: failed to request IRQ %d: %d\n",
-+ mmc_hostname(mmc), host->irq, ret);
-+ goto untasklet;
-+ }
-+
-+ mmiowb();
-+ mmc_add_host(mmc);
-+
-+ pio_limit_string[0] = '\0';
-+ if (host->have_dma && (host->pio_limit > 0))
-+ sprintf(pio_limit_string, " (>%d)", host->pio_limit);
-+ pr_info("%s: %s loaded - DMA %s%s\n",
-+ mmc_hostname(mmc), DRIVER_NAME,
-+ host->have_dma ? "enabled" : "disabled",
-+ pio_limit_string);
-+
-+ return 0;
-+
-+untasklet:
-+ tasklet_kill(&host->finish_tasklet);
-+
-+ return ret;
-+}
-+
-+static int bcm2835_sdhost_probe(struct platform_device *pdev)
-+{
-+ struct device *dev = &pdev->dev;
-+ struct device_node *node = dev->of_node;
-+ struct clk *clk;
-+ struct resource *iomem;
-+ struct bcm2835_host *host;
-+ struct mmc_host *mmc;
-+ const __be32 *addr;
-+ int ret;
-+
-+ pr_debug("bcm2835_sdhost_probe\n");
-+ mmc = mmc_alloc_host(sizeof(*host), dev);
-+ if (!mmc)
-+ return -ENOMEM;
-+
-+ mmc->ops = &bcm2835_sdhost_ops;
-+ host = mmc_priv(mmc);
-+ host->mmc = mmc;
-+ host->pio_timeout = msecs_to_jiffies(500);
-+ host->max_delay = 1; /* Warn if over 1ms */
-+ spin_lock_init(&host->lock);
-+
-+ iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+ host->ioaddr = devm_ioremap_resource(dev, iomem);
-+ if (IS_ERR(host->ioaddr)) {
-+ ret = PTR_ERR(host->ioaddr);
-+ goto err;
-+ }
-+
-+ addr = of_get_address(node, 0, NULL, NULL);
-+ if (!addr) {
-+ dev_err(dev, "could not get DMA-register address\n");
-+ return -ENODEV;
-+ }
-+ host->bus_addr = be32_to_cpup(addr);
-+ pr_debug(" - ioaddr %lx, iomem->start %lx, bus_addr %lx\n",
-+ (unsigned long)host->ioaddr,
-+ (unsigned long)iomem->start,
-+ (unsigned long)host->bus_addr);
-+
-+ host->allow_dma = ALLOW_DMA;
-+
-+ if (node) {
-+ /* Read any custom properties */
-+ of_property_read_u32(node,
-+ "brcm,delay-after-stop",
-+ &host->delay_after_stop);
-+ of_property_read_u32(node,
-+ "brcm,overclock-50",
-+ &host->overclock_50);
-+ of_property_read_u32(node,
-+ "brcm,pio-limit",
-+ &host->pio_limit);
-+ host->allow_dma = ALLOW_DMA &&
-+ !of_property_read_bool(node, "brcm,force-pio");
-+ host->debug = of_property_read_bool(node, "brcm,debug");
-+ }
-+
-+ if (host->allow_dma) {
-+ if (node) {
-+ host->dma_chan_tx =
-+ dma_request_slave_channel(dev, "tx");
-+ host->dma_chan_rx =
-+ dma_request_slave_channel(dev, "rx");
-+ } else {
-+ dma_cap_mask_t mask;
-+
-+ dma_cap_zero(mask);
-+ /* we don't care about the channel, any would work */
-+ dma_cap_set(DMA_SLAVE, mask);
-+ host->dma_chan_tx =
-+ dma_request_channel(mask, NULL, NULL);
-+ host->dma_chan_rx =
-+ dma_request_channel(mask, NULL, NULL);
-+ }
-+ }
-+
-+ clk = devm_clk_get(dev, NULL);
-+ if (IS_ERR(clk)) {
-+ dev_err(dev, "could not get clk\n");
-+ ret = PTR_ERR(clk);
-+ goto err;
-+ }
-+
-+ host->max_clk = clk_get_rate(clk);
-+
-+ host->irq = platform_get_irq(pdev, 0);
-+ if (host->irq <= 0) {
-+ dev_err(dev, "get IRQ failed\n");
-+ ret = -EINVAL;
-+ goto err;
-+ }
-+
-+ pr_debug(" - max_clk %lx, irq %d\n",
-+ (unsigned long)host->max_clk,
-+ (int)host->irq);
-+
-+ if (node)
-+ mmc_of_parse(mmc);
-+ else
-+ mmc->caps |= MMC_CAP_4_BIT_DATA;
-+
-+ ret = bcm2835_sdhost_add_host(host);
-+ if (ret)
-+ goto err;
-+
-+ platform_set_drvdata(pdev, host);
-+
-+ pr_debug("bcm2835_sdhost_probe -> OK\n");
-+
-+ return 0;
-+
-+err:
-+ pr_debug("bcm2835_sdhost_probe -> err %d\n", ret);
-+ mmc_free_host(mmc);
-+
-+ return ret;
-+}
-+
-+static int bcm2835_sdhost_remove(struct platform_device *pdev)
-+{
-+ struct bcm2835_host *host = platform_get_drvdata(pdev);
-+
-+ pr_debug("bcm2835_sdhost_remove\n");
-+
-+ mmc_remove_host(host->mmc);
-+
-+ bcm2835_sdhost_set_power(host, false);
-+
-+ free_irq(host->irq, host);
-+
-+ del_timer_sync(&host->timer);
-+
-+ tasklet_kill(&host->finish_tasklet);
-+
-+ mmc_free_host(host->mmc);
-+ platform_set_drvdata(pdev, NULL);
-+
-+ pr_debug("bcm2835_sdhost_remove - OK\n");
-+ return 0;
-+}
-+
-+
-+static const struct of_device_id bcm2835_sdhost_match[] = {
-+ { .compatible = "brcm,bcm2835-sdhost" },
-+ { }
-+};
-+MODULE_DEVICE_TABLE(of, bcm2835_sdhost_match);
-+
-+
-+
-+static struct platform_driver bcm2835_sdhost_driver = {
-+ .probe = bcm2835_sdhost_probe,
-+ .remove = bcm2835_sdhost_remove,
-+ .driver = {
-+ .name = DRIVER_NAME,
-+ .owner = THIS_MODULE,
-+ .of_match_table = bcm2835_sdhost_match,
-+ },
-+};
-+module_platform_driver(bcm2835_sdhost_driver);
-+
-+MODULE_ALIAS("platform:sdhost-bcm2835");
-+MODULE_DESCRIPTION("BCM2835 SDHost driver");
-+MODULE_LICENSE("GPL v2");
-+MODULE_AUTHOR("Phil Elwell");
diff --git a/target/linux/brcm2708/patches-4.4/0034-cma-Add-vc_cma-driver-to-enable-use-of-CMA.patch b/target/linux/brcm2708/patches-4.4/0034-cma-Add-vc_cma-driver-to-enable-use-of-CMA.patch
deleted file mode 100644
index 48e1fd7..0000000
--- a/target/linux/brcm2708/patches-4.4/0034-cma-Add-vc_cma-driver-to-enable-use-of-CMA.patch
+++ /dev/null
@@ -1,1326 +0,0 @@
-From 471fff7d975619ae7fb98c1dee8f75d8cdcdf93c Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Wed, 3 Jul 2013 00:31:47 +0100
-Subject: [PATCH] cma: Add vc_cma driver to enable use of CMA
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Signed-off-by: popcornmix <popcornmix at gmail.com>
-
-vc_cma: Make the vc_cma area the default contiguous DMA area
-
-vc_cma: Provide empty functions when module is not built
-
-Providing empty functions saves the users from guarding the
-function call with an #if clause.
-Move __init markings from prototypes to functions.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
----
- drivers/char/Kconfig | 2 +
- drivers/char/Makefile | 1 +
- drivers/char/broadcom/Kconfig | 15 +
- drivers/char/broadcom/Makefile | 1 +
- drivers/char/broadcom/vc_cma/Makefile | 14 +
- drivers/char/broadcom/vc_cma/vc_cma.c | 1193 +++++++++++++++++++++++++++++++++
- include/linux/broadcom/vc_cma.h | 36 +
- 7 files changed, 1262 insertions(+)
- create mode 100644 drivers/char/broadcom/Kconfig
- create mode 100644 drivers/char/broadcom/Makefile
- create mode 100644 drivers/char/broadcom/vc_cma/Makefile
- create mode 100644 drivers/char/broadcom/vc_cma/vc_cma.c
- create mode 100644 include/linux/broadcom/vc_cma.h
-
---- a/drivers/char/Kconfig
-+++ b/drivers/char/Kconfig
-@@ -4,6 +4,8 @@
-
- menu "Character devices"
-
-+source "drivers/char/broadcom/Kconfig"
-+
- source "drivers/tty/Kconfig"
-
- config DEVMEM
---- a/drivers/char/Makefile
-+++ b/drivers/char/Makefile
-@@ -60,3 +60,4 @@ js-rtc-y = rtc.o
-
- obj-$(CONFIG_TILE_SROM) += tile-srom.o
- obj-$(CONFIG_XILLYBUS) += xillybus/
-+obj-$(CONFIG_BRCM_CHAR_DRIVERS) += broadcom/
---- /dev/null
-+++ b/drivers/char/broadcom/Kconfig
-@@ -0,0 +1,15 @@
-+#
-+# Broadcom char driver config
-+#
-+
-+menuconfig BRCM_CHAR_DRIVERS
-+ bool "Broadcom Char Drivers"
-+ help
-+ Broadcom's char drivers
-+
-+config BCM_VC_CMA
-+ bool "Videocore CMA"
-+ depends on CMA && BRCM_CHAR_DRIVERS && BCM2708_VCHIQ
-+ default n
-+ help
-+ Helper for videocore CMA access.
---- /dev/null
-+++ b/drivers/char/broadcom/Makefile
-@@ -0,0 +1 @@
-+obj-$(CONFIG_BCM_VC_CMA) += vc_cma/
---- /dev/null
-+++ b/drivers/char/broadcom/vc_cma/Makefile
-@@ -0,0 +1,14 @@
-+ccflags-y += -Wall -Wstrict-prototypes -Wno-trigraphs
-+ccflags-y += -Werror
-+ccflags-y += -Iinclude/linux/broadcom
-+ccflags-y += -Idrivers/misc/vc04_services
-+ccflags-y += -Idrivers/misc/vc04_services/interface/vchi
-+ccflags-y += -Idrivers/misc/vc04_services/interface/vchiq_arm
-+
-+ccflags-y += -D__KERNEL__
-+ccflags-y += -D__linux__
-+ccflags-y += -Werror
-+
-+obj-$(CONFIG_BCM_VC_CMA) += vc-cma.o
-+
-+vc-cma-objs := vc_cma.o
---- /dev/null
-+++ b/drivers/char/broadcom/vc_cma/vc_cma.c
-@@ -0,0 +1,1193 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+#include <linux/kthread.h>
-+#include <linux/fs.h>
-+#include <linux/device.h>
-+#include <linux/cdev.h>
-+#include <linux/mm.h>
-+#include <linux/proc_fs.h>
-+#include <linux/seq_file.h>
-+#include <linux/dma-mapping.h>
-+#include <linux/dma-contiguous.h>
-+#include <linux/platform_device.h>
-+#include <linux/uaccess.h>
-+#include <asm/cacheflush.h>
-+
-+#include "vc_cma.h"
-+
-+#include "vchiq_util.h"
-+#include "vchiq_connected.h"
-+//#include "debug_sym.h"
-+//#include "vc_mem.h"
-+
-+#define DRIVER_NAME "vc-cma"
-+
-+#define LOG_DBG(fmt, ...) \
-+ if (vc_cma_debug) \
-+ printk(KERN_INFO fmt "\n", ##__VA_ARGS__)
-+#define LOG_INFO(fmt, ...) \
-+ printk(KERN_INFO fmt "\n", ##__VA_ARGS__)
-+#define LOG_ERR(fmt, ...) \
-+ printk(KERN_ERR fmt "\n", ##__VA_ARGS__)
-+
-+#define VC_CMA_FOURCC VCHIQ_MAKE_FOURCC('C', 'M', 'A', ' ')
-+#define VC_CMA_VERSION 2
-+
-+#define VC_CMA_CHUNK_ORDER 6 /* 256K */
-+#define VC_CMA_CHUNK_SIZE (4096 << VC_CMA_CHUNK_ORDER)
-+#define VC_CMA_MAX_PARAMS_PER_MSG \
-+ ((VCHIQ_MAX_MSG_SIZE - sizeof(unsigned short))/sizeof(unsigned short))
-+#define VC_CMA_RESERVE_COUNT_MAX 16
-+
-+#define PAGES_PER_CHUNK (VC_CMA_CHUNK_SIZE / PAGE_SIZE)
-+
-+#define VCADDR_TO_PHYSADDR(vcaddr) (mm_vc_mem_phys_addr + vcaddr)
-+
-+#define loud_error(...) \
-+ LOG_ERR("===== " __VA_ARGS__)
-+
-+enum {
-+ VC_CMA_MSG_QUIT,
-+ VC_CMA_MSG_OPEN,
-+ VC_CMA_MSG_TICK,
-+ VC_CMA_MSG_ALLOC, /* chunk count */
-+ VC_CMA_MSG_FREE, /* chunk, chunk, ... */
-+ VC_CMA_MSG_ALLOCATED, /* chunk, chunk, ... */
-+ VC_CMA_MSG_REQUEST_ALLOC, /* chunk count */
-+ VC_CMA_MSG_REQUEST_FREE, /* chunk count */
-+ VC_CMA_MSG_RESERVE, /* bytes lo, bytes hi */
-+ VC_CMA_MSG_UPDATE_RESERVE,
-+ VC_CMA_MSG_MAX
-+};
-+
-+struct cma_msg {
-+ unsigned short type;
-+ unsigned short params[VC_CMA_MAX_PARAMS_PER_MSG];
-+};
-+
-+struct vc_cma_reserve_user {
-+ unsigned int pid;
-+ unsigned int reserve;
-+};
-+
-+/* Device (/dev) related variables */
-+static dev_t vc_cma_devnum;
-+static struct class *vc_cma_class;
-+static struct cdev vc_cma_cdev;
-+static int vc_cma_inited;
-+static int vc_cma_debug;
-+
-+/* Proc entry */
-+static struct proc_dir_entry *vc_cma_proc_entry;
-+
-+phys_addr_t vc_cma_base;
-+struct page *vc_cma_base_page;
-+unsigned int vc_cma_size;
-+EXPORT_SYMBOL(vc_cma_size);
-+unsigned int vc_cma_initial;
-+unsigned int vc_cma_chunks;
-+unsigned int vc_cma_chunks_used;
-+unsigned int vc_cma_chunks_reserved;
-+
-+
-+void *vc_cma_dma_alloc;
-+unsigned int vc_cma_dma_size;
-+
-+static int in_loud_error;
-+
-+unsigned int vc_cma_reserve_total;
-+unsigned int vc_cma_reserve_count;
-+struct vc_cma_reserve_user vc_cma_reserve_users[VC_CMA_RESERVE_COUNT_MAX];
-+static DEFINE_SEMAPHORE(vc_cma_reserve_mutex);
-+static DEFINE_SEMAPHORE(vc_cma_worker_queue_push_mutex);
-+
-+static u64 vc_cma_dma_mask = DMA_BIT_MASK(32);
-+static struct platform_device vc_cma_device = {
-+ .name = "vc-cma",
-+ .id = 0,
-+ .dev = {
-+ .dma_mask = &vc_cma_dma_mask,
-+ .coherent_dma_mask = DMA_BIT_MASK(32),
-+ },
-+};
-+
-+static VCHIQ_INSTANCE_T cma_instance;
-+static VCHIQ_SERVICE_HANDLE_T cma_service;
-+static VCHIU_QUEUE_T cma_msg_queue;
-+static struct task_struct *cma_worker;
-+
-+static int vc_cma_set_reserve(unsigned int reserve, unsigned int pid);
-+static int vc_cma_alloc_chunks(int num_chunks, struct cma_msg *reply);
-+static VCHIQ_STATUS_T cma_service_callback(VCHIQ_REASON_T reason,
-+ VCHIQ_HEADER_T * header,
-+ VCHIQ_SERVICE_HANDLE_T service,
-+ void *bulk_userdata);
-+static void send_vc_msg(unsigned short type,
-+ unsigned short param1, unsigned short param2);
-+static bool send_worker_msg(VCHIQ_HEADER_T * msg);
-+
-+static int early_vc_cma_mem(char *p)
-+{
-+ unsigned int new_size;
-+ printk(KERN_NOTICE "early_vc_cma_mem(%s)", p);
-+ vc_cma_size = memparse(p, &p);
-+ vc_cma_initial = vc_cma_size;
-+ if (*p == '/')
-+ vc_cma_size = memparse(p + 1, &p);
-+ if (*p == '@')
-+ vc_cma_base = memparse(p + 1, &p);
-+
-+ new_size = (vc_cma_size - ((-vc_cma_base) & (VC_CMA_CHUNK_SIZE - 1)))
-+ & ~(VC_CMA_CHUNK_SIZE - 1);
-+ if (new_size > vc_cma_size)
-+ vc_cma_size = 0;
-+ vc_cma_initial = (vc_cma_initial + VC_CMA_CHUNK_SIZE - 1)
-+ & ~(VC_CMA_CHUNK_SIZE - 1);
-+ if (vc_cma_initial > vc_cma_size)
-+ vc_cma_initial = vc_cma_size;
-+ vc_cma_base = (vc_cma_base + VC_CMA_CHUNK_SIZE - 1)
-+ & ~(VC_CMA_CHUNK_SIZE - 1);
-+
-+ printk(KERN_NOTICE " -> initial %x, size %x, base %x", vc_cma_initial,
-+ vc_cma_size, (unsigned int)vc_cma_base);
-+
-+ return 0;
-+}
-+
-+early_param("vc-cma-mem", early_vc_cma_mem);
-+
-+void __init vc_cma_early_init(void)
-+{
-+ LOG_DBG("vc_cma_early_init - vc_cma_chunks = %d", vc_cma_chunks);
-+ if (vc_cma_size) {
-+ int rc = platform_device_register(&vc_cma_device);
-+ LOG_DBG("platform_device_register -> %d", rc);
-+ }
-+}
-+
-+void __init vc_cma_reserve(void)
-+{
-+ /* if vc_cma_size is set, then declare vc CMA area of the same
-+ * size from the end of memory
-+ */
-+ if (vc_cma_size) {
-+ if (dma_declare_contiguous(&vc_cma_device.dev, vc_cma_size,
-+ vc_cma_base, 0) == 0) {
-+ if (!dev_get_cma_area(NULL)) {
-+ /* There is no default CMA area - make this
-+ the default */
-+ struct cma *vc_cma_area = dev_get_cma_area(
-+ &vc_cma_device.dev);
-+ dma_contiguous_set_default(vc_cma_area);
-+ LOG_INFO("vc_cma_reserve - using vc_cma as "
-+ "the default contiguous DMA area");
-+ }
-+ } else {
-+ LOG_ERR("vc_cma: dma_declare_contiguous(%x,%x) failed",
-+ vc_cma_size, (unsigned int)vc_cma_base);
-+ vc_cma_size = 0;
-+ }
-+ }
-+ vc_cma_chunks = vc_cma_size / VC_CMA_CHUNK_SIZE;
-+}
-+
-+/****************************************************************************
-+*
-+* vc_cma_open
-+*
-+***************************************************************************/
-+
-+static int vc_cma_open(struct inode *inode, struct file *file)
-+{
-+ (void)inode;
-+ (void)file;
-+
-+ return 0;
-+}
-+
-+/****************************************************************************
-+*
-+* vc_cma_release
-+*
-+***************************************************************************/
-+
-+static int vc_cma_release(struct inode *inode, struct file *file)
-+{
-+ (void)inode;
-+ (void)file;
-+
-+ vc_cma_set_reserve(0, current->tgid);
-+
-+ return 0;
-+}
-+
-+/****************************************************************************
-+*
-+* vc_cma_ioctl
-+*
-+***************************************************************************/
-+
-+static long vc_cma_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
-+{
-+ int rc = 0;
-+
-+ (void)cmd;
-+ (void)arg;
-+
-+ switch (cmd) {
-+ case VC_CMA_IOC_RESERVE:
-+ rc = vc_cma_set_reserve((unsigned int)arg, current->tgid);
-+ if (rc >= 0)
-+ rc = 0;
-+ break;
-+ default:
-+ LOG_ERR("vc-cma: Unknown ioctl %x", cmd);
-+ return -ENOTTY;
-+ }
-+
-+ return rc;
-+}
-+
-+/****************************************************************************
-+*
-+* File Operations for the driver.
-+*
-+***************************************************************************/
-+
-+static const struct file_operations vc_cma_fops = {
-+ .owner = THIS_MODULE,
-+ .open = vc_cma_open,
-+ .release = vc_cma_release,
-+ .unlocked_ioctl = vc_cma_ioctl,
-+};
-+
-+/****************************************************************************
-+*
-+* vc_cma_proc_open
-+*
-+***************************************************************************/
-+
-+static int vc_cma_show_info(struct seq_file *m, void *v)
-+{
-+ int i;
-+
-+ seq_printf(m, "Videocore CMA:\n");
-+ seq_printf(m, " Base : %08x\n", (unsigned int)vc_cma_base);
-+ seq_printf(m, " Length : %08x\n", vc_cma_size);
-+ seq_printf(m, " Initial : %08x\n", vc_cma_initial);
-+ seq_printf(m, " Chunk size : %08x\n", VC_CMA_CHUNK_SIZE);
-+ seq_printf(m, " Chunks : %4d (%d bytes)\n",
-+ (int)vc_cma_chunks,
-+ (int)(vc_cma_chunks * VC_CMA_CHUNK_SIZE));
-+ seq_printf(m, " Used : %4d (%d bytes)\n",
-+ (int)vc_cma_chunks_used,
-+ (int)(vc_cma_chunks_used * VC_CMA_CHUNK_SIZE));
-+ seq_printf(m, " Reserved : %4d (%d bytes)\n",
-+ (unsigned int)vc_cma_chunks_reserved,
-+ (int)(vc_cma_chunks_reserved * VC_CMA_CHUNK_SIZE));
-+
-+ for (i = 0; i < vc_cma_reserve_count; i++) {
-+ struct vc_cma_reserve_user *user = &vc_cma_reserve_users[i];
-+ seq_printf(m, " PID %5d: %d bytes\n", user->pid,
-+ user->reserve);
-+ }
-+ seq_printf(m, " dma_alloc : %p (%d pages)\n",
-+ vc_cma_dma_alloc ? page_address(vc_cma_dma_alloc) : 0,
-+ vc_cma_dma_size);
-+
-+ seq_printf(m, "\n");
-+
-+ return 0;
-+}
-+
-+static int vc_cma_proc_open(struct inode *inode, struct file *file)
-+{
-+ return single_open(file, vc_cma_show_info, NULL);
-+}
-+
-+/****************************************************************************
-+*
-+* vc_cma_proc_write
-+*
-+***************************************************************************/
-+
-+static int vc_cma_proc_write(struct file *file,
-+ const char __user *buffer,
-+ size_t size, loff_t *ppos)
-+{
-+ int rc = -EFAULT;
-+ char input_str[20];
-+
-+ memset(input_str, 0, sizeof(input_str));
-+
-+ if (size > sizeof(input_str)) {
-+ LOG_ERR("%s: input string length too long", __func__);
-+ goto out;
-+ }
-+
-+ if (copy_from_user(input_str, buffer, size - 1)) {
-+ LOG_ERR("%s: failed to get input string", __func__);
-+ goto out;
-+ }
-+#define ALLOC_STR "alloc"
-+#define FREE_STR "free"
-+#define DEBUG_STR "debug"
-+#define RESERVE_STR "reserve"
-+#define DMA_ALLOC_STR "dma_alloc"
-+#define DMA_FREE_STR "dma_free"
-+ if (strncmp(input_str, ALLOC_STR, strlen(ALLOC_STR)) == 0) {
-+ int alloc_size;
-+ char *p = input_str + strlen(ALLOC_STR);
-+
-+ while (*p == ' ')
-+ p++;
-+ alloc_size = memparse(p, NULL);
-+ LOG_INFO("/proc/vc-cma: alloc %d", alloc_size);
-+ if (alloc_size)
-+ send_vc_msg(VC_CMA_MSG_REQUEST_FREE,
-+ alloc_size / VC_CMA_CHUNK_SIZE, 0);
-+ else
-+ LOG_ERR("invalid size '%s'", p);
-+ rc = size;
-+ } else if (strncmp(input_str, FREE_STR, strlen(FREE_STR)) == 0) {
-+ int alloc_size;
-+ char *p = input_str + strlen(FREE_STR);
-+
-+ while (*p == ' ')
-+ p++;
-+ alloc_size = memparse(p, NULL);
-+ LOG_INFO("/proc/vc-cma: free %d", alloc_size);
-+ if (alloc_size)
-+ send_vc_msg(VC_CMA_MSG_REQUEST_ALLOC,
-+ alloc_size / VC_CMA_CHUNK_SIZE, 0);
-+ else
-+ LOG_ERR("invalid size '%s'", p);
-+ rc = size;
-+ } else if (strncmp(input_str, DEBUG_STR, strlen(DEBUG_STR)) == 0) {
-+ char *p = input_str + strlen(DEBUG_STR);
-+ while (*p == ' ')
-+ p++;
-+ if ((strcmp(p, "on") == 0) || (strcmp(p, "1") == 0))
-+ vc_cma_debug = 1;
-+ else if ((strcmp(p, "off") == 0) || (strcmp(p, "0") == 0))
-+ vc_cma_debug = 0;
-+ LOG_INFO("/proc/vc-cma: debug %s", vc_cma_debug ? "on" : "off");
-+ rc = size;
-+ } else if (strncmp(input_str, RESERVE_STR, strlen(RESERVE_STR)) == 0) {
-+ int alloc_size;
-+ int reserved;
-+ char *p = input_str + strlen(RESERVE_STR);
-+ while (*p == ' ')
-+ p++;
-+ alloc_size = memparse(p, NULL);
-+
-+ reserved = vc_cma_set_reserve(alloc_size, current->tgid);
-+ rc = (reserved >= 0) ? size : reserved;
-+ } else if (strncmp(input_str, DMA_ALLOC_STR, strlen(DMA_ALLOC_STR)) == 0) {
-+ int alloc_size;
-+ char *p = input_str + strlen(DMA_ALLOC_STR);
-+ while (*p == ' ')
-+ p++;
-+ alloc_size = memparse(p, NULL);
-+
-+ if (vc_cma_dma_alloc) {
-+ dma_release_from_contiguous(NULL, vc_cma_dma_alloc,
-+ vc_cma_dma_size);
-+ vc_cma_dma_alloc = NULL;
-+ vc_cma_dma_size = 0;
-+ }
-+ vc_cma_dma_alloc = dma_alloc_from_contiguous(NULL, alloc_size, 0);
-+ vc_cma_dma_size = (vc_cma_dma_alloc ? alloc_size : 0);
-+ if (vc_cma_dma_alloc)
-+ LOG_INFO("dma_alloc(%d pages) -> %p", alloc_size, page_address(vc_cma_dma_alloc));
-+ else
-+ LOG_ERR("dma_alloc(%d pages) failed", alloc_size);
-+ rc = size;
-+ } else if (strncmp(input_str, DMA_FREE_STR, strlen(DMA_FREE_STR)) == 0) {
-+ if (vc_cma_dma_alloc) {
-+ dma_release_from_contiguous(NULL, vc_cma_dma_alloc,
-+ vc_cma_dma_size);
-+ vc_cma_dma_alloc = NULL;
-+ vc_cma_dma_size = 0;
-+ }
-+ rc = size;
-+ }
-+
-+out:
-+ return rc;
-+}
-+
-+/****************************************************************************
-+*
-+* File Operations for /proc interface.
-+*
-+***************************************************************************/
-+
-+static const struct file_operations vc_cma_proc_fops = {
-+ .open = vc_cma_proc_open,
-+ .read = seq_read,
-+ .write = vc_cma_proc_write,
-+ .llseek = seq_lseek,
-+ .release = single_release
-+};
-+
-+static int vc_cma_set_reserve(unsigned int reserve, unsigned int pid)
-+{
-+ struct vc_cma_reserve_user *user = NULL;
-+ int delta = 0;
-+ int i;
-+
-+ if (down_interruptible(&vc_cma_reserve_mutex))
-+ return -ERESTARTSYS;
-+
-+ for (i = 0; i < vc_cma_reserve_count; i++) {
-+ if (pid == vc_cma_reserve_users[i].pid) {
-+ user = &vc_cma_reserve_users[i];
-+ delta = reserve - user->reserve;
-+ if (reserve)
-+ user->reserve = reserve;
-+ else {
-+ /* Remove this entry by copying downwards */
-+ while ((i + 1) < vc_cma_reserve_count) {
-+ user[0].pid = user[1].pid;
-+ user[0].reserve = user[1].reserve;
-+ user++;
-+ i++;
-+ }
-+ vc_cma_reserve_count--;
-+ user = NULL;
-+ }
-+ break;
-+ }
-+ }
-+
-+ if (reserve && !user) {
-+ if (vc_cma_reserve_count == VC_CMA_RESERVE_COUNT_MAX) {
-+ LOG_ERR("vc-cma: Too many reservations - "
-+ "increase CMA_RESERVE_COUNT_MAX");
-+ up(&vc_cma_reserve_mutex);
-+ return -EBUSY;
-+ }
-+ user = &vc_cma_reserve_users[vc_cma_reserve_count];
-+ user->pid = pid;
-+ user->reserve = reserve;
-+ delta = reserve;
-+ vc_cma_reserve_count++;
-+ }
-+
-+ vc_cma_reserve_total += delta;
-+
-+ send_vc_msg(VC_CMA_MSG_RESERVE,
-+ vc_cma_reserve_total & 0xffff, vc_cma_reserve_total >> 16);
-+
-+ send_worker_msg((VCHIQ_HEADER_T *) VC_CMA_MSG_UPDATE_RESERVE);
-+
-+ LOG_DBG("/proc/vc-cma: reserve %d (PID %d) - total %u",
-+ reserve, pid, vc_cma_reserve_total);
-+
-+ up(&vc_cma_reserve_mutex);
-+
-+ return vc_cma_reserve_total;
-+}
-+
-+static VCHIQ_STATUS_T cma_service_callback(VCHIQ_REASON_T reason,
-+ VCHIQ_HEADER_T * header,
-+ VCHIQ_SERVICE_HANDLE_T service,
-+ void *bulk_userdata)
-+{
-+ switch (reason) {
-+ case VCHIQ_MESSAGE_AVAILABLE:
-+ if (!send_worker_msg(header))
-+ return VCHIQ_RETRY;
-+ break;
-+ case VCHIQ_SERVICE_CLOSED:
-+ LOG_DBG("CMA service closed");
-+ break;
-+ default:
-+ LOG_ERR("Unexpected CMA callback reason %d", reason);
-+ break;
-+ }
-+ return VCHIQ_SUCCESS;
-+}
-+
-+static void send_vc_msg(unsigned short type,
-+ unsigned short param1, unsigned short param2)
-+{
-+ unsigned short msg[] = { type, param1, param2 };
-+ VCHIQ_ELEMENT_T elem = { &msg, sizeof(msg) };
-+ VCHIQ_STATUS_T ret;
-+ vchiq_use_service(cma_service);
-+ ret = vchiq_queue_message(cma_service, &elem, 1);
-+ vchiq_release_service(cma_service);
-+ if (ret != VCHIQ_SUCCESS)
-+ LOG_ERR("vchiq_queue_message returned %x", ret);
-+}
-+
-+static bool send_worker_msg(VCHIQ_HEADER_T * msg)
-+{
-+ if (down_interruptible(&vc_cma_worker_queue_push_mutex))
-+ return false;
-+ vchiu_queue_push(&cma_msg_queue, msg);
-+ up(&vc_cma_worker_queue_push_mutex);
-+ return true;
-+}
-+
-+static int vc_cma_alloc_chunks(int num_chunks, struct cma_msg *reply)
-+{
-+ int i;
-+ for (i = 0; i < num_chunks; i++) {
-+ struct page *chunk;
-+ unsigned int chunk_num;
-+ uint8_t *chunk_addr;
-+ size_t chunk_size = PAGES_PER_CHUNK << PAGE_SHIFT;
-+
-+ chunk = dma_alloc_from_contiguous(&vc_cma_device.dev,
-+ PAGES_PER_CHUNK,
-+ VC_CMA_CHUNK_ORDER);
-+ if (!chunk)
-+ break;
-+
-+ chunk_addr = page_address(chunk);
-+ dmac_flush_range(chunk_addr, chunk_addr + chunk_size);
-+ outer_inv_range(__pa(chunk_addr), __pa(chunk_addr) +
-+ chunk_size);
-+
-+ chunk_num =
-+ (page_to_phys(chunk) - vc_cma_base) / VC_CMA_CHUNK_SIZE;
-+ BUG_ON(((page_to_phys(chunk) - vc_cma_base) %
-+ VC_CMA_CHUNK_SIZE) != 0);
-+ if (chunk_num >= vc_cma_chunks) {
-+ phys_addr_t _pa = vc_cma_base + vc_cma_size - 1;
-+ LOG_ERR("%s: ===============================",
-+ __func__);
-+ LOG_ERR("%s: chunk phys %x, vc_cma %pa-%pa - "
-+ "bad SPARSEMEM configuration?",
-+ __func__, (unsigned int)page_to_phys(chunk),
-+ &vc_cma_base, &_pa);
-+ LOG_ERR("%s: dev->cma_area = %p", __func__,
-+ (void*)0/*vc_cma_device.dev.cma_area*/);
-+ LOG_ERR("%s: ===============================",
-+ __func__);
-+ break;
-+ }
-+ reply->params[i] = chunk_num;
-+ vc_cma_chunks_used++;
-+ }
-+
-+ if (i < num_chunks) {
-+ LOG_ERR("%s: dma_alloc_from_contiguous failed "
-+ "for %x bytes (alloc %d of %d, %d free)",
-+ __func__, VC_CMA_CHUNK_SIZE, i,
-+ num_chunks, vc_cma_chunks - vc_cma_chunks_used);
-+ num_chunks = i;
-+ }
-+
-+ LOG_DBG("CMA allocated %d chunks -> %d used",
-+ num_chunks, vc_cma_chunks_used);
-+ reply->type = VC_CMA_MSG_ALLOCATED;
-+
-+ {
-+ VCHIQ_ELEMENT_T elem = {
-+ reply,
-+ offsetof(struct cma_msg, params[0]) +
-+ num_chunks * sizeof(reply->params[0])
-+ };
-+ VCHIQ_STATUS_T ret;
-+ vchiq_use_service(cma_service);
-+ ret = vchiq_queue_message(cma_service, &elem, 1);
-+ vchiq_release_service(cma_service);
-+ if (ret != VCHIQ_SUCCESS)
-+ LOG_ERR("vchiq_queue_message return " "%x", ret);
-+ }
-+
-+ return num_chunks;
-+}
-+
-+static int cma_worker_proc(void *param)
-+{
-+ static struct cma_msg reply;
-+ (void)param;
-+
-+ while (1) {
-+ VCHIQ_HEADER_T *msg;
-+ static struct cma_msg msg_copy;
-+ struct cma_msg *cma_msg = &msg_copy;
-+ int type, msg_size;
-+
-+ msg = vchiu_queue_pop(&cma_msg_queue);
-+ if ((unsigned int)msg >= VC_CMA_MSG_MAX) {
-+ msg_size = msg->size;
-+ memcpy(&msg_copy, msg->data, msg_size);
-+ type = cma_msg->type;
-+ vchiq_release_message(cma_service, msg);
-+ } else {
-+ msg_size = 0;
-+ type = (int)msg;
-+ if (type == VC_CMA_MSG_QUIT)
-+ break;
-+ else if (type == VC_CMA_MSG_UPDATE_RESERVE) {
-+ msg = NULL;
-+ cma_msg = NULL;
-+ } else {
-+ BUG();
-+ continue;
-+ }
-+ }
-+
-+ switch (type) {
-+ case VC_CMA_MSG_ALLOC:{
-+ int num_chunks, free_chunks;
-+ num_chunks = cma_msg->params[0];
-+ free_chunks =
-+ vc_cma_chunks - vc_cma_chunks_used;
-+ LOG_DBG("CMA_MSG_ALLOC(%d chunks)", num_chunks);
-+ if (num_chunks > VC_CMA_MAX_PARAMS_PER_MSG) {
-+ LOG_ERR
-+ ("CMA_MSG_ALLOC - chunk count (%d) "
-+ "exceeds VC_CMA_MAX_PARAMS_PER_MSG (%d)",
-+ num_chunks,
-+ VC_CMA_MAX_PARAMS_PER_MSG);
-+ num_chunks = VC_CMA_MAX_PARAMS_PER_MSG;
-+ }
-+
-+ if (num_chunks > free_chunks) {
-+ LOG_ERR
-+ ("CMA_MSG_ALLOC - chunk count (%d) "
-+ "exceeds free chunks (%d)",
-+ num_chunks, free_chunks);
-+ num_chunks = free_chunks;
-+ }
-+
-+ vc_cma_alloc_chunks(num_chunks, &reply);
-+ }
-+ break;
-+
-+ case VC_CMA_MSG_FREE:{
-+ int chunk_count =
-+ (msg_size -
-+ offsetof(struct cma_msg,
-+ params)) /
-+ sizeof(cma_msg->params[0]);
-+ int i;
-+ BUG_ON(chunk_count <= 0);
-+
-+ LOG_DBG("CMA_MSG_FREE(%d chunks - %x, ...)",
-+ chunk_count, cma_msg->params[0]);
-+ for (i = 0; i < chunk_count; i++) {
-+ int chunk_num = cma_msg->params[i];
-+ struct page *page = vc_cma_base_page +
-+ chunk_num * PAGES_PER_CHUNK;
-+ if (chunk_num >= vc_cma_chunks) {
-+ LOG_ERR
-+ ("CMA_MSG_FREE - chunk %d of %d"
-+ " (value %x) exceeds maximum "
-+ "(%x)", i, chunk_count,
-+ chunk_num,
-+ vc_cma_chunks - 1);
-+ break;
-+ }
-+
-+ if (!dma_release_from_contiguous
-+ (&vc_cma_device.dev, page,
-+ PAGES_PER_CHUNK)) {
-+ phys_addr_t _pa = page_to_phys(page);
-+ LOG_ERR
-+ ("CMA_MSG_FREE - failed to "
-+ "release chunk %d (phys %pa, "
-+ "page %x)", chunk_num,
-+ &_pa,
-+ (unsigned int)page);
-+ }
-+ vc_cma_chunks_used--;
-+ }
-+ LOG_DBG("CMA released %d chunks -> %d used",
-+ i, vc_cma_chunks_used);
-+ }
-+ break;
-+
-+ case VC_CMA_MSG_UPDATE_RESERVE:{
-+ int chunks_needed =
-+ ((vc_cma_reserve_total + VC_CMA_CHUNK_SIZE -
-+ 1)
-+ / VC_CMA_CHUNK_SIZE) -
-+ vc_cma_chunks_reserved;
-+
-+ LOG_DBG
-+ ("CMA_MSG_UPDATE_RESERVE(%d chunks needed)",
-+ chunks_needed);
-+
-+ /* Cap the reservations to what is available */
-+ if (chunks_needed > 0) {
-+ if (chunks_needed >
-+ (vc_cma_chunks -
-+ vc_cma_chunks_used))
-+ chunks_needed =
-+ (vc_cma_chunks -
-+ vc_cma_chunks_used);
-+
-+ chunks_needed =
-+ vc_cma_alloc_chunks(chunks_needed,
-+ &reply);
-+ }
-+
-+ LOG_DBG
-+ ("CMA_MSG_UPDATE_RESERVE(%d chunks allocated)",
-+ chunks_needed);
-+ vc_cma_chunks_reserved += chunks_needed;
-+ }
-+ break;
-+
-+ default:
-+ LOG_ERR("unexpected msg type %d", type);
-+ break;
-+ }
-+ }
-+
-+ LOG_DBG("quitting...");
-+ return 0;
-+}
-+
-+/****************************************************************************
-+*
-+* vc_cma_connected_init
-+*
-+* This function is called once the videocore has been connected.
-+*
-+***************************************************************************/
-+
-+static void vc_cma_connected_init(void)
-+{
-+ VCHIQ_SERVICE_PARAMS_T service_params;
-+
-+ LOG_DBG("vc_cma_connected_init");
-+
-+ if (!vchiu_queue_init(&cma_msg_queue, 16)) {
-+ LOG_ERR("could not create CMA msg queue");
-+ goto fail_queue;
-+ }
-+
-+ if (vchiq_initialise(&cma_instance) != VCHIQ_SUCCESS)
-+ goto fail_vchiq_init;
-+
-+ vchiq_connect(cma_instance);
-+
-+ service_params.fourcc = VC_CMA_FOURCC;
-+ service_params.callback = cma_service_callback;
-+ service_params.userdata = NULL;
-+ service_params.version = VC_CMA_VERSION;
-+ service_params.version_min = VC_CMA_VERSION;
-+
-+ if (vchiq_open_service(cma_instance, &service_params,
-+ &cma_service) != VCHIQ_SUCCESS) {
-+ LOG_ERR("failed to open service - already in use?");
-+ goto fail_vchiq_open;
-+ }
-+
-+ vchiq_release_service(cma_service);
-+
-+ cma_worker = kthread_create(cma_worker_proc, NULL, "cma_worker");
-+ if (!cma_worker) {
-+ LOG_ERR("could not create CMA worker thread");
-+ goto fail_worker;
-+ }
-+ set_user_nice(cma_worker, -20);
-+ wake_up_process(cma_worker);
-+
-+ return;
-+
-+fail_worker:
-+ vchiq_close_service(cma_service);
-+fail_vchiq_open:
-+ vchiq_shutdown(cma_instance);
-+fail_vchiq_init:
-+ vchiu_queue_delete(&cma_msg_queue);
-+fail_queue:
-+ return;
-+}
-+
-+void
-+loud_error_header(void)
-+{
-+ if (in_loud_error)
-+ return;
-+
-+ LOG_ERR("============================================================"
-+ "================");
-+ LOG_ERR("============================================================"
-+ "================");
-+ LOG_ERR("=====");
-+
-+ in_loud_error = 1;
-+}
-+
-+void
-+loud_error_footer(void)
-+{
-+ if (!in_loud_error)
-+ return;
-+
-+ LOG_ERR("=====");
-+ LOG_ERR("============================================================"
-+ "================");
-+ LOG_ERR("============================================================"
-+ "================");
-+
-+ in_loud_error = 0;
-+}
-+
-+#if 1
-+static int check_cma_config(void) { return 1; }
-+#else
-+static int
-+read_vc_debug_var(VC_MEM_ACCESS_HANDLE_T handle,
-+ const char *symbol,
-+ void *buf, size_t bufsize)
-+{
-+ VC_MEM_ADDR_T vcMemAddr;
-+ size_t vcMemSize;
-+ uint8_t *mapAddr;
-+ off_t vcMapAddr;
-+
-+ if (!LookupVideoCoreSymbol(handle, symbol,
-+ &vcMemAddr,
-+ &vcMemSize)) {
-+ loud_error_header();
-+ loud_error(
-+ "failed to find VC symbol \"%s\".",
-+ symbol);
-+ loud_error_footer();
-+ return 0;
-+ }
-+
-+ if (vcMemSize != bufsize) {
-+ loud_error_header();
-+ loud_error(
-+ "VC symbol \"%s\" is the wrong size.",
-+ symbol);
-+ loud_error_footer();
-+ return 0;
-+ }
-+
-+ vcMapAddr = (off_t)vcMemAddr & VC_MEM_TO_ARM_ADDR_MASK;
-+ vcMapAddr += mm_vc_mem_phys_addr;
-+ mapAddr = ioremap_nocache(vcMapAddr, vcMemSize);
-+ if (mapAddr == 0) {
-+ loud_error_header();
-+ loud_error(
-+ "failed to ioremap \"%s\" @ 0x%x "
-+ "(phys: 0x%x, size: %u).",
-+ symbol,
-+ (unsigned int)vcMapAddr,
-+ (unsigned int)vcMemAddr,
-+ (unsigned int)vcMemSize);
-+ loud_error_footer();
-+ return 0;
-+ }
-+
-+ memcpy(buf, mapAddr, bufsize);
-+ iounmap(mapAddr);
-+
-+ return 1;
-+}
-+
-+
-+static int
-+check_cma_config(void)
-+{
-+ VC_MEM_ACCESS_HANDLE_T mem_hndl;
-+ VC_MEM_ADDR_T mempool_start;
-+ VC_MEM_ADDR_T mempool_end;
-+ VC_MEM_ADDR_T mempool_offline_start;
-+ VC_MEM_ADDR_T mempool_offline_end;
-+ VC_MEM_ADDR_T cam_alloc_base;
-+ VC_MEM_ADDR_T cam_alloc_size;
-+ VC_MEM_ADDR_T cam_alloc_end;
-+ int success = 0;
-+
-+ if (OpenVideoCoreMemory(&mem_hndl) != 0)
-+ goto out;
-+
-+ /* Read the relevant VideoCore variables */
-+ if (!read_vc_debug_var(mem_hndl, "__MEMPOOL_START",
-+ &mempool_start,
-+ sizeof(mempool_start)))
-+ goto close;
-+
-+ if (!read_vc_debug_var(mem_hndl, "__MEMPOOL_END",
-+ &mempool_end,
-+ sizeof(mempool_end)))
-+ goto close;
-+
-+ if (!read_vc_debug_var(mem_hndl, "__MEMPOOL_OFFLINE_START",
-+ &mempool_offline_start,
-+ sizeof(mempool_offline_start)))
-+ goto close;
-+
-+ if (!read_vc_debug_var(mem_hndl, "__MEMPOOL_OFFLINE_END",
-+ &mempool_offline_end,
-+ sizeof(mempool_offline_end)))
-+ goto close;
-+
-+ if (!read_vc_debug_var(mem_hndl, "cam_alloc_base",
-+ &cam_alloc_base,
-+ sizeof(cam_alloc_base)))
-+ goto close;
-+
-+ if (!read_vc_debug_var(mem_hndl, "cam_alloc_size",
-+ &cam_alloc_size,
-+ sizeof(cam_alloc_size)))
-+ goto close;
-+
-+ cam_alloc_end = cam_alloc_base + cam_alloc_size;
-+
-+ success = 1;
-+
-+ /* Now the sanity checks */
-+ if (!mempool_offline_start)
-+ mempool_offline_start = mempool_start;
-+ if (!mempool_offline_end)
-+ mempool_offline_end = mempool_end;
-+
-+ if (VCADDR_TO_PHYSADDR(mempool_offline_start) != vc_cma_base) {
-+ loud_error_header();
-+ loud_error(
-+ "__MEMPOOL_OFFLINE_START(%x -> %lx) doesn't match "
-+ "vc_cma_base(%x)",
-+ mempool_offline_start,
-+ VCADDR_TO_PHYSADDR(mempool_offline_start),
-+ vc_cma_base);
-+ success = 0;
-+ }
-+
-+ if (VCADDR_TO_PHYSADDR(mempool_offline_end) !=
-+ (vc_cma_base + vc_cma_size)) {
-+ loud_error_header();
-+ loud_error(
-+ "__MEMPOOL_OFFLINE_END(%x -> %lx) doesn't match "
-+ "vc_cma_base(%x) + vc_cma_size(%x) = %x",
-+ mempool_offline_start,
-+ VCADDR_TO_PHYSADDR(mempool_offline_end),
-+ vc_cma_base, vc_cma_size, vc_cma_base + vc_cma_size);
-+ success = 0;
-+ }
-+
-+ if (mempool_end < mempool_start) {
-+ loud_error_header();
-+ loud_error(
-+ "__MEMPOOL_END(%x) must not be before "
-+ "__MEMPOOL_START(%x)",
-+ mempool_end,
-+ mempool_start);
-+ success = 0;
-+ }
-+
-+ if (mempool_offline_end < mempool_offline_start) {
-+ loud_error_header();
-+ loud_error(
-+ "__MEMPOOL_OFFLINE_END(%x) must not be before "
-+ "__MEMPOOL_OFFLINE_START(%x)",
-+ mempool_offline_end,
-+ mempool_offline_start);
-+ success = 0;
-+ }
-+
-+ if (mempool_offline_start < mempool_start) {
-+ loud_error_header();
-+ loud_error(
-+ "__MEMPOOL_OFFLINE_START(%x) must not be before "
-+ "__MEMPOOL_START(%x)",
-+ mempool_offline_start,
-+ mempool_start);
-+ success = 0;
-+ }
-+
-+ if (mempool_offline_end > mempool_end) {
-+ loud_error_header();
-+ loud_error(
-+ "__MEMPOOL_OFFLINE_END(%x) must not be after "
-+ "__MEMPOOL_END(%x)",
-+ mempool_offline_end,
-+ mempool_end);
-+ success = 0;
-+ }
-+
-+ if ((cam_alloc_base < mempool_end) &&
-+ (cam_alloc_end > mempool_start)) {
-+ loud_error_header();
-+ loud_error(
-+ "cam_alloc pool(%x-%x) overlaps "
-+ "mempool(%x-%x)",
-+ cam_alloc_base, cam_alloc_end,
-+ mempool_start, mempool_end);
-+ success = 0;
-+ }
-+
-+ loud_error_footer();
-+
-+close:
-+ CloseVideoCoreMemory(mem_hndl);
-+
-+out:
-+ return success;
-+}
-+#endif
-+
-+static int vc_cma_init(void)
-+{
-+ int rc = -EFAULT;
-+ struct device *dev;
-+
-+ if (!check_cma_config())
-+ goto out_release;
-+
-+ LOG_INFO("vc-cma: Videocore CMA driver");
-+ LOG_INFO("vc-cma: vc_cma_base = %pa", &vc_cma_base);
-+ LOG_INFO("vc-cma: vc_cma_size = 0x%08x (%u MiB)",
-+ vc_cma_size, vc_cma_size / (1024 * 1024));
-+ LOG_INFO("vc-cma: vc_cma_initial = 0x%08x (%u MiB)",
-+ vc_cma_initial, vc_cma_initial / (1024 * 1024));
-+
-+ vc_cma_base_page = phys_to_page(vc_cma_base);
-+
-+ if (vc_cma_chunks) {
-+ int chunks_needed = vc_cma_initial / VC_CMA_CHUNK_SIZE;
-+
-+ for (vc_cma_chunks_used = 0;
-+ vc_cma_chunks_used < chunks_needed; vc_cma_chunks_used++) {
-+ struct page *chunk;
-+ chunk = dma_alloc_from_contiguous(&vc_cma_device.dev,
-+ PAGES_PER_CHUNK,
-+ VC_CMA_CHUNK_ORDER);
-+ if (!chunk)
-+ break;
-+ BUG_ON(((page_to_phys(chunk) - vc_cma_base) %
-+ VC_CMA_CHUNK_SIZE) != 0);
-+ }
-+ if (vc_cma_chunks_used != chunks_needed) {
-+ LOG_ERR("%s: dma_alloc_from_contiguous failed (%d "
-+ "bytes, allocation %d of %d)",
-+ __func__, VC_CMA_CHUNK_SIZE,
-+ vc_cma_chunks_used, chunks_needed);
-+ goto out_release;
-+ }
-+
-+ vchiq_add_connected_callback(vc_cma_connected_init);
-+ }
-+
-+ rc = alloc_chrdev_region(&vc_cma_devnum, 0, 1, DRIVER_NAME);
-+ if (rc < 0) {
-+ LOG_ERR("%s: alloc_chrdev_region failed (rc=%d)", __func__, rc);
-+ goto out_release;
-+ }
-+
-+ cdev_init(&vc_cma_cdev, &vc_cma_fops);
-+ rc = cdev_add(&vc_cma_cdev, vc_cma_devnum, 1);
-+ if (rc != 0) {
-+ LOG_ERR("%s: cdev_add failed (rc=%d)", __func__, rc);
-+ goto out_unregister;
-+ }
-+
-+ vc_cma_class = class_create(THIS_MODULE, DRIVER_NAME);
-+ if (IS_ERR(vc_cma_class)) {
-+ rc = PTR_ERR(vc_cma_class);
-+ LOG_ERR("%s: class_create failed (rc=%d)", __func__, rc);
-+ goto out_cdev_del;
-+ }
-+
-+ dev = device_create(vc_cma_class, NULL, vc_cma_devnum, NULL,
-+ DRIVER_NAME);
-+ if (IS_ERR(dev)) {
-+ rc = PTR_ERR(dev);
-+ LOG_ERR("%s: device_create failed (rc=%d)", __func__, rc);
-+ goto out_class_destroy;
-+ }
-+
-+ vc_cma_proc_entry = proc_create(DRIVER_NAME, 0444, NULL, &vc_cma_proc_fops);
-+ if (vc_cma_proc_entry == NULL) {
-+ rc = -EFAULT;
-+ LOG_ERR("%s: proc_create failed", __func__);
-+ goto out_device_destroy;
-+ }
-+
-+ vc_cma_inited = 1;
-+ return 0;
-+
-+out_device_destroy:
-+ device_destroy(vc_cma_class, vc_cma_devnum);
-+
-+out_class_destroy:
-+ class_destroy(vc_cma_class);
-+ vc_cma_class = NULL;
-+
-+out_cdev_del:
-+ cdev_del(&vc_cma_cdev);
-+
-+out_unregister:
-+ unregister_chrdev_region(vc_cma_devnum, 1);
-+
-+out_release:
-+ /* It is tempting to try to clean up by calling
-+ dma_release_from_contiguous for all allocated chunks, but it isn't
-+ a very safe thing to do. If vc_cma_initial is non-zero it is because
-+ VideoCore is already using that memory, so giving it back to Linux
-+ is likely to be fatal.
-+ */
-+ return -1;
-+}
-+
-+/****************************************************************************
-+*
-+* vc_cma_exit
-+*
-+***************************************************************************/
-+
-+static void __exit vc_cma_exit(void)
-+{
-+ LOG_DBG("%s: called", __func__);
-+
-+ if (vc_cma_inited) {
-+ remove_proc_entry(DRIVER_NAME, NULL);
-+ device_destroy(vc_cma_class, vc_cma_devnum);
-+ class_destroy(vc_cma_class);
-+ cdev_del(&vc_cma_cdev);
-+ unregister_chrdev_region(vc_cma_devnum, 1);
-+ }
-+}
-+
-+module_init(vc_cma_init);
-+module_exit(vc_cma_exit);
-+MODULE_LICENSE("GPL");
-+MODULE_AUTHOR("Broadcom Corporation");
---- /dev/null
-+++ b/include/linux/broadcom/vc_cma.h
-@@ -0,0 +1,36 @@
-+/*****************************************************************************
-+* Copyright 2012 Broadcom Corporation. All rights reserved.
-+*
-+* Unless you and Broadcom execute a separate written software license
-+* agreement governing use of this software, this software is licensed to you
-+* under the terms of the GNU General Public License version 2, available at
-+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
-+*
-+* Notwithstanding the above, under no circumstances may you combine this
-+* software in any way with any other Broadcom software provided under a
-+* license other than the GPL, without Broadcom's express prior written
-+* consent.
-+*****************************************************************************/
-+
-+#if !defined( VC_CMA_H )
-+#define VC_CMA_H
-+
-+#include <linux/ioctl.h>
-+
-+#define VC_CMA_IOC_MAGIC 0xc5
-+
-+#define VC_CMA_IOC_RESERVE _IO(VC_CMA_IOC_MAGIC, 0)
-+
-+#ifdef __KERNEL__
-+
-+#ifdef CONFIG_BCM_VC_CMA
-+void vc_cma_early_init(void);
-+void vc_cma_reserve(void);
-+#else
-+static inline void vc_cma_early_init(void) { }
-+static inline void vc_cma_reserve(void) { }
-+#endif
-+
-+#endif
-+
-+#endif /* VC_CMA_H */
diff --git a/target/linux/brcm2708/patches-4.4/0035-bcm2708-alsa-sound-driver.patch b/target/linux/brcm2708/patches-4.4/0035-bcm2708-alsa-sound-driver.patch
deleted file mode 100644
index 68a271e..0000000
--- a/target/linux/brcm2708/patches-4.4/0035-bcm2708-alsa-sound-driver.patch
+++ /dev/null
@@ -1,2678 +0,0 @@
-From 5a28ef1d7eec56824139996cb43a5423bc15279f Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Mon, 26 Mar 2012 22:15:50 +0100
-Subject: [PATCH] bcm2708: alsa sound driver
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Signed-off-by: popcornmix <popcornmix at gmail.com>
-
-alsa: add mmap support and some cleanups to bcm2835 ALSA driver
-
-snd-bcm2835: Add support for spdif/hdmi passthrough
-
-This adds a dedicated subdevice which can be used for passthrough of non-audio
-formats (ie encoded a52) through the hdmi audio link. In addition to this
-driver extension an appropriate card config is required to make alsa-lib
-support the AES parameters for this device.
-
-snd-bcm2708: Add mutex, improve logging
-
-Fix for ALSA driver crash
-
-Avoids an issue when closing and opening vchiq where a message can arrive before service handle has been written
-
-alsa: reduce severity of expected warning message
-
-snd-bcm2708: Fix dmesg spam for non-error case
-
-alsa: Ensure mutexes are released through error paths
-
-alsa: Make interrupted close paths quieter
-
-BCM270x: Add onboard sound device to Device Tree
-
-Add Device Tree support to alsa driver.
-Add device to Device Tree.
-Don't add platform devices when booting in DT mode.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
----
- sound/arm/Kconfig | 8 +
- sound/arm/Makefile | 5 +
- sound/arm/bcm2835-ctl.c | 323 +++++++++++++
- sound/arm/bcm2835-pcm.c | 557 +++++++++++++++++++++++
- sound/arm/bcm2835-vchiq.c | 902 +++++++++++++++++++++++++++++++++++++
- sound/arm/bcm2835.c | 511 +++++++++++++++++++++
- sound/arm/bcm2835.h | 167 +++++++
- sound/arm/vc_vchi_audioserv_defs.h | 116 +++++
- 8 files changed, 2589 insertions(+)
- create mode 100755 sound/arm/bcm2835-ctl.c
- create mode 100755 sound/arm/bcm2835-pcm.c
- create mode 100755 sound/arm/bcm2835-vchiq.c
- create mode 100644 sound/arm/bcm2835.c
- create mode 100755 sound/arm/bcm2835.h
- create mode 100644 sound/arm/vc_vchi_audioserv_defs.h
-
---- a/sound/arm/Kconfig
-+++ b/sound/arm/Kconfig
-@@ -40,5 +40,13 @@ config SND_PXA2XX_AC97
- Say Y or M if you want to support any AC97 codec attached to
- the PXA2xx AC97 interface.
-
-+config SND_BCM2835
-+ tristate "BCM2835 ALSA driver"
-+ depends on (ARCH_BCM2708 || ARCH_BCM2709 || ARCH_BCM2835) \
-+ && BCM2708_VCHIQ && SND
-+ select SND_PCM
-+ help
-+ Say Y or M if you want to support BCM2835 Alsa pcm card driver
-+
- endif # SND_ARM
-
---- a/sound/arm/Makefile
-+++ b/sound/arm/Makefile
-@@ -14,3 +14,8 @@ snd-pxa2xx-lib-$(CONFIG_SND_PXA2XX_LIB_A
-
- obj-$(CONFIG_SND_PXA2XX_AC97) += snd-pxa2xx-ac97.o
- snd-pxa2xx-ac97-objs := pxa2xx-ac97.o
-+
-+obj-$(CONFIG_SND_BCM2835) += snd-bcm2835.o
-+snd-bcm2835-objs := bcm2835.o bcm2835-ctl.o bcm2835-pcm.o bcm2835-vchiq.o
-+
-+ccflags-y += -Idrivers/misc/vc04_services -Idrivers/misc/vc04_services/interface/vcos/linuxkernel -D__VCCOREVER__=0x04000000
---- /dev/null
-+++ b/sound/arm/bcm2835-ctl.c
-@@ -0,0 +1,323 @@
-+/*****************************************************************************
-+* Copyright 2011 Broadcom Corporation. All rights reserved.
-+*
-+* Unless you and Broadcom execute a separate written software license
-+* agreement governing use of this software, this software is licensed to you
-+* under the terms of the GNU General Public License version 2, available at
-+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
-+*
-+* Notwithstanding the above, under no circumstances may you combine this
-+* software in any way with any other Broadcom software provided under a
-+* license other than the GPL, without Broadcom's express prior written
-+* consent.
-+*****************************************************************************/
-+
-+#include <linux/platform_device.h>
-+#include <linux/init.h>
-+#include <linux/io.h>
-+#include <linux/jiffies.h>
-+#include <linux/slab.h>
-+#include <linux/time.h>
-+#include <linux/wait.h>
-+#include <linux/delay.h>
-+#include <linux/moduleparam.h>
-+#include <linux/sched.h>
-+
-+#include <sound/core.h>
-+#include <sound/control.h>
-+#include <sound/pcm.h>
-+#include <sound/pcm_params.h>
-+#include <sound/rawmidi.h>
-+#include <sound/initval.h>
-+#include <sound/tlv.h>
-+#include <sound/asoundef.h>
-+
-+#include "bcm2835.h"
-+
-+/* volume maximum and minimum in terms of 0.01dB */
-+#define CTRL_VOL_MAX 400
-+#define CTRL_VOL_MIN -10239 /* originally -10240 */
-+
-+
-+static int snd_bcm2835_ctl_info(struct snd_kcontrol *kcontrol,
-+ struct snd_ctl_elem_info *uinfo)
-+{
-+ audio_info(" ... IN\n");
-+ if (kcontrol->private_value == PCM_PLAYBACK_VOLUME) {
-+ uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER;
-+ uinfo->count = 1;
-+ uinfo->value.integer.min = CTRL_VOL_MIN;
-+ uinfo->value.integer.max = CTRL_VOL_MAX; /* 2303 */
-+ } else if (kcontrol->private_value == PCM_PLAYBACK_MUTE) {
-+ uinfo->type = SNDRV_CTL_ELEM_TYPE_BOOLEAN;
-+ uinfo->count = 1;
-+ uinfo->value.integer.min = 0;
-+ uinfo->value.integer.max = 1;
-+ } else if (kcontrol->private_value == PCM_PLAYBACK_DEVICE) {
-+ uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER;
-+ uinfo->count = 1;
-+ uinfo->value.integer.min = 0;
-+ uinfo->value.integer.max = AUDIO_DEST_MAX-1;
-+ }
-+ audio_info(" ... OUT\n");
-+ return 0;
-+}
-+
-+/* toggles mute on or off depending on the value of nmute, and returns
-+ * 1 if the mute value was changed, otherwise 0
-+ */
-+static int toggle_mute(struct bcm2835_chip *chip, int nmute)
-+{
-+ /* if settings are ok, just return 0 */
-+ if(chip->mute == nmute)
-+ return 0;
-+
-+ /* if the sound is muted then we need to unmute */
-+ if(chip->mute == CTRL_VOL_MUTE)
-+ {
-+ chip->volume = chip->old_volume; /* copy the old volume back */
-+ audio_info("Unmuting, old_volume = %d, volume = %d ...\n", chip->old_volume, chip->volume);
-+ }
-+ else /* otherwise we mute */
-+ {
-+ chip->old_volume = chip->volume;
-+ chip->volume = 26214; /* set volume to minimum level AKA mute */
-+ audio_info("Muting, old_volume = %d, volume = %d ...\n", chip->old_volume, chip->volume);
-+ }
-+
-+ chip->mute = nmute;
-+ return 1;
-+}
-+
-+static int snd_bcm2835_ctl_get(struct snd_kcontrol *kcontrol,
-+ struct snd_ctl_elem_value *ucontrol)
-+{
-+ struct bcm2835_chip *chip = snd_kcontrol_chip(kcontrol);
-+
-+ BUG_ON(!chip && !(chip->avail_substreams & AVAIL_SUBSTREAMS_MASK));
-+
-+ if (kcontrol->private_value == PCM_PLAYBACK_VOLUME)
-+ ucontrol->value.integer.value[0] = chip2alsa(chip->volume);
-+ else if (kcontrol->private_value == PCM_PLAYBACK_MUTE)
-+ ucontrol->value.integer.value[0] = chip->mute;
-+ else if (kcontrol->private_value == PCM_PLAYBACK_DEVICE)
-+ ucontrol->value.integer.value[0] = chip->dest;
-+
-+ return 0;
-+}
-+
-+static int snd_bcm2835_ctl_put(struct snd_kcontrol *kcontrol,
-+ struct snd_ctl_elem_value *ucontrol)
-+{
-+ struct bcm2835_chip *chip = snd_kcontrol_chip(kcontrol);
-+ int changed = 0;
-+
-+ if (kcontrol->private_value == PCM_PLAYBACK_VOLUME) {
-+ audio_info("Volume change attempted.. volume = %d new_volume = %d\n", chip->volume, (int)ucontrol->value.integer.value[0]);
-+ if (chip->mute == CTRL_VOL_MUTE) {
-+ /* changed = toggle_mute(chip, CTRL_VOL_UNMUTE); */
-+ return 1; /* should return 0 to signify no change but the mixer takes this as the opposite sign (no idea why) */
-+ }
-+ if (changed
-+ || (ucontrol->value.integer.value[0] != chip2alsa(chip->volume))) {
-+
-+ chip->volume = alsa2chip(ucontrol->value.integer.value[0]);
-+ changed = 1;
-+ }
-+
-+ } else if (kcontrol->private_value == PCM_PLAYBACK_MUTE) {
-+ /* Now implemented */
-+ audio_info(" Mute attempted\n");
-+ changed = toggle_mute(chip, ucontrol->value.integer.value[0]);
-+
-+ } else if (kcontrol->private_value == PCM_PLAYBACK_DEVICE) {
-+ if (ucontrol->value.integer.value[0] != chip->dest) {
-+ chip->dest = ucontrol->value.integer.value[0];
-+ changed = 1;
-+ }
-+ }
-+
-+ if (changed) {
-+ if (bcm2835_audio_set_ctls(chip))
-+ printk(KERN_ERR "Failed to set ALSA controls..\n");
-+ }
-+
-+ return changed;
-+}
-+
-+static DECLARE_TLV_DB_SCALE(snd_bcm2835_db_scale, CTRL_VOL_MIN, 1, 1);
-+
-+static struct snd_kcontrol_new snd_bcm2835_ctl[] = {
-+ {
-+ .iface = SNDRV_CTL_ELEM_IFACE_MIXER,
-+ .name = "PCM Playback Volume",
-+ .index = 0,
-+ .access = SNDRV_CTL_ELEM_ACCESS_READWRITE | SNDRV_CTL_ELEM_ACCESS_TLV_READ,
-+ .private_value = PCM_PLAYBACK_VOLUME,
-+ .info = snd_bcm2835_ctl_info,
-+ .get = snd_bcm2835_ctl_get,
-+ .put = snd_bcm2835_ctl_put,
-+ .count = 1,
-+ .tlv = {.p = snd_bcm2835_db_scale}
-+ },
-+ {
-+ .iface = SNDRV_CTL_ELEM_IFACE_MIXER,
-+ .name = "PCM Playback Switch",
-+ .index = 0,
-+ .access = SNDRV_CTL_ELEM_ACCESS_READWRITE,
-+ .private_value = PCM_PLAYBACK_MUTE,
-+ .info = snd_bcm2835_ctl_info,
-+ .get = snd_bcm2835_ctl_get,
-+ .put = snd_bcm2835_ctl_put,
-+ .count = 1,
-+ },
-+ {
-+ .iface = SNDRV_CTL_ELEM_IFACE_MIXER,
-+ .name = "PCM Playback Route",
-+ .index = 0,
-+ .access = SNDRV_CTL_ELEM_ACCESS_READWRITE,
-+ .private_value = PCM_PLAYBACK_DEVICE,
-+ .info = snd_bcm2835_ctl_info,
-+ .get = snd_bcm2835_ctl_get,
-+ .put = snd_bcm2835_ctl_put,
-+ .count = 1,
-+ },
-+};
-+
-+static int snd_bcm2835_spdif_default_info(struct snd_kcontrol *kcontrol,
-+ struct snd_ctl_elem_info *uinfo)
-+{
-+ uinfo->type = SNDRV_CTL_ELEM_TYPE_IEC958;
-+ uinfo->count = 1;
-+ return 0;
-+}
-+
-+static int snd_bcm2835_spdif_default_get(struct snd_kcontrol *kcontrol,
-+ struct snd_ctl_elem_value *ucontrol)
-+{
-+ struct bcm2835_chip *chip = snd_kcontrol_chip(kcontrol);
-+ int i;
-+
-+ for (i = 0; i < 4; i++)
-+ ucontrol->value.iec958.status[i] =
-+ (chip->spdif_status >> (i * 8)) && 0xff;
-+
-+ return 0;
-+}
-+
-+static int snd_bcm2835_spdif_default_put(struct snd_kcontrol *kcontrol,
-+ struct snd_ctl_elem_value *ucontrol)
-+{
-+ struct bcm2835_chip *chip = snd_kcontrol_chip(kcontrol);
-+ unsigned int val = 0;
-+ int i, change;
-+
-+ for (i = 0; i < 4; i++)
-+ val |= (unsigned int)ucontrol->value.iec958.status[i] << (i * 8);
-+
-+ change = val != chip->spdif_status;
-+ chip->spdif_status = val;
-+
-+ return change;
-+}
-+
-+static int snd_bcm2835_spdif_mask_info(struct snd_kcontrol *kcontrol,
-+ struct snd_ctl_elem_info *uinfo)
-+{
-+ uinfo->type = SNDRV_CTL_ELEM_TYPE_IEC958;
-+ uinfo->count = 1;
-+ return 0;
-+}
-+
-+static int snd_bcm2835_spdif_mask_get(struct snd_kcontrol *kcontrol,
-+ struct snd_ctl_elem_value *ucontrol)
-+{
-+ /* bcm2835 supports only consumer mode and sets all other format flags
-+ * automatically. So the only thing left is signalling non-audio
-+ * content */
-+ ucontrol->value.iec958.status[0] = IEC958_AES0_NONAUDIO;
-+ return 0;
-+}
-+
-+static int snd_bcm2835_spdif_stream_info(struct snd_kcontrol *kcontrol,
-+ struct snd_ctl_elem_info *uinfo)
-+{
-+ uinfo->type = SNDRV_CTL_ELEM_TYPE_IEC958;
-+ uinfo->count = 1;
-+ return 0;
-+}
-+
-+static int snd_bcm2835_spdif_stream_get(struct snd_kcontrol *kcontrol,
-+ struct snd_ctl_elem_value *ucontrol)
-+{
-+ struct bcm2835_chip *chip = snd_kcontrol_chip(kcontrol);
-+ int i;
-+
-+ for (i = 0; i < 4; i++)
-+ ucontrol->value.iec958.status[i] =
-+ (chip->spdif_status >> (i * 8)) & 0xff;
-+ return 0;
-+}
-+
-+static int snd_bcm2835_spdif_stream_put(struct snd_kcontrol *kcontrol,
-+ struct snd_ctl_elem_value *ucontrol)
-+{
-+ struct bcm2835_chip *chip = snd_kcontrol_chip(kcontrol);
-+ unsigned int val = 0;
-+ int i, change;
-+
-+ for (i = 0; i < 4; i++)
-+ val |= (unsigned int)ucontrol->value.iec958.status[i] << (i * 8);
-+ change = val != chip->spdif_status;
-+ chip->spdif_status = val;
-+
-+ return change;
-+}
-+
-+static struct snd_kcontrol_new snd_bcm2835_spdif[] = {
-+ {
-+ .iface = SNDRV_CTL_ELEM_IFACE_PCM,
-+ .name = SNDRV_CTL_NAME_IEC958("", PLAYBACK, DEFAULT),
-+ .info = snd_bcm2835_spdif_default_info,
-+ .get = snd_bcm2835_spdif_default_get,
-+ .put = snd_bcm2835_spdif_default_put
-+ },
-+ {
-+ .access = SNDRV_CTL_ELEM_ACCESS_READ,
-+ .iface = SNDRV_CTL_ELEM_IFACE_PCM,
-+ .name = SNDRV_CTL_NAME_IEC958("", PLAYBACK, CON_MASK),
-+ .info = snd_bcm2835_spdif_mask_info,
-+ .get = snd_bcm2835_spdif_mask_get,
-+ },
-+ {
-+ .access = SNDRV_CTL_ELEM_ACCESS_READWRITE |
-+ SNDRV_CTL_ELEM_ACCESS_INACTIVE,
-+ .iface = SNDRV_CTL_ELEM_IFACE_PCM,
-+ .name = SNDRV_CTL_NAME_IEC958("", PLAYBACK, PCM_STREAM),
-+ .info = snd_bcm2835_spdif_stream_info,
-+ .get = snd_bcm2835_spdif_stream_get,
-+ .put = snd_bcm2835_spdif_stream_put,
-+ },
-+};
-+
-+int snd_bcm2835_new_ctl(bcm2835_chip_t * chip)
-+{
-+ int err;
-+ unsigned int idx;
-+
-+ strcpy(chip->card->mixername, "Broadcom Mixer");
-+ for (idx = 0; idx < ARRAY_SIZE(snd_bcm2835_ctl); idx++) {
-+ err =
-+ snd_ctl_add(chip->card,
-+ snd_ctl_new1(&snd_bcm2835_ctl[idx], chip));
-+ if (err < 0)
-+ return err;
-+ }
-+ for (idx = 0; idx < ARRAY_SIZE(snd_bcm2835_spdif); idx++) {
-+ err = snd_ctl_add(chip->card,
-+ snd_ctl_new1(&snd_bcm2835_spdif[idx], chip));
-+ if (err < 0)
-+ return err;
-+ }
-+ return 0;
-+}
---- /dev/null
-+++ b/sound/arm/bcm2835-pcm.c
-@@ -0,0 +1,557 @@
-+/*****************************************************************************
-+* Copyright 2011 Broadcom Corporation. All rights reserved.
-+*
-+* Unless you and Broadcom execute a separate written software license
-+* agreement governing use of this software, this software is licensed to you
-+* under the terms of the GNU General Public License version 2, available at
-+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
-+*
-+* Notwithstanding the above, under no circumstances may you combine this
-+* software in any way with any other Broadcom software provided under a
-+* license other than the GPL, without Broadcom's express prior written
-+* consent.
-+*****************************************************************************/
-+
-+#include <linux/interrupt.h>
-+#include <linux/slab.h>
-+
-+#include <sound/asoundef.h>
-+
-+#include "bcm2835.h"
-+
-+/* hardware definition */
-+static struct snd_pcm_hardware snd_bcm2835_playback_hw = {
-+ .info = (SNDRV_PCM_INFO_INTERLEAVED | SNDRV_PCM_INFO_BLOCK_TRANSFER |
-+ SNDRV_PCM_INFO_MMAP | SNDRV_PCM_INFO_MMAP_VALID),
-+ .formats = SNDRV_PCM_FMTBIT_U8 | SNDRV_PCM_FMTBIT_S16_LE,
-+ .rates = SNDRV_PCM_RATE_CONTINUOUS | SNDRV_PCM_RATE_8000_48000,
-+ .rate_min = 8000,
-+ .rate_max = 48000,
-+ .channels_min = 1,
-+ .channels_max = 2,
-+ .buffer_bytes_max = 128 * 1024,
-+ .period_bytes_min = 1 * 1024,
-+ .period_bytes_max = 128 * 1024,
-+ .periods_min = 1,
-+ .periods_max = 128,
-+};
-+
-+static struct snd_pcm_hardware snd_bcm2835_playback_spdif_hw = {
-+ .info = (SNDRV_PCM_INFO_INTERLEAVED | SNDRV_PCM_INFO_BLOCK_TRANSFER |
-+ SNDRV_PCM_INFO_MMAP | SNDRV_PCM_INFO_MMAP_VALID),
-+ .formats = SNDRV_PCM_FMTBIT_S16_LE,
-+ .rates = SNDRV_PCM_RATE_CONTINUOUS | SNDRV_PCM_RATE_44100 |
-+ SNDRV_PCM_RATE_48000,
-+ .rate_min = 44100,
-+ .rate_max = 48000,
-+ .channels_min = 2,
-+ .channels_max = 2,
-+ .buffer_bytes_max = 128 * 1024,
-+ .period_bytes_min = 1 * 1024,
-+ .period_bytes_max = 128 * 1024,
-+ .periods_min = 1,
-+ .periods_max = 128,
-+};
-+
-+static void snd_bcm2835_playback_free(struct snd_pcm_runtime *runtime)
-+{
-+ audio_info("Freeing up alsa stream here ..\n");
-+ if (runtime->private_data)
-+ kfree(runtime->private_data);
-+ runtime->private_data = NULL;
-+}
-+
-+static irqreturn_t bcm2835_playback_fifo_irq(int irq, void *dev_id)
-+{
-+ bcm2835_alsa_stream_t *alsa_stream = (bcm2835_alsa_stream_t *) dev_id;
-+ uint32_t consumed = 0;
-+ int new_period = 0;
-+
-+ audio_info(" .. IN\n");
-+
-+ audio_info("alsa_stream=%p substream=%p\n", alsa_stream,
-+ alsa_stream ? alsa_stream->substream : 0);
-+
-+ if (alsa_stream->open)
-+ consumed = bcm2835_audio_retrieve_buffers(alsa_stream);
-+
-+ /* We get called only if playback was triggered, So, the number of buffers we retrieve in
-+ * each iteration are the buffers that have been played out already
-+ */
-+
-+ if (alsa_stream->period_size) {
-+ if ((alsa_stream->pos / alsa_stream->period_size) !=
-+ ((alsa_stream->pos + consumed) / alsa_stream->period_size))
-+ new_period = 1;
-+ }
-+ audio_debug("updating pos cur: %d + %d max:%d period_bytes:%d, hw_ptr: %d new_period:%d\n",
-+ alsa_stream->pos,
-+ consumed,
-+ alsa_stream->buffer_size,
-+ (int)(alsa_stream->period_size*alsa_stream->substream->runtime->periods),
-+ frames_to_bytes(alsa_stream->substream->runtime, alsa_stream->substream->runtime->status->hw_ptr),
-+ new_period);
-+ if (alsa_stream->buffer_size) {
-+ alsa_stream->pos += consumed &~ (1<<30);
-+ alsa_stream->pos %= alsa_stream->buffer_size;
-+ }
-+
-+ if (alsa_stream->substream) {
-+ if (new_period)
-+ snd_pcm_period_elapsed(alsa_stream->substream);
-+ } else {
-+ audio_warning(" unexpected NULL substream\n");
-+ }
-+ audio_info(" .. OUT\n");
-+
-+ return IRQ_HANDLED;
-+}
-+
-+/* open callback */
-+static int snd_bcm2835_playback_open_generic(
-+ struct snd_pcm_substream *substream, int spdif)
-+{
-+ bcm2835_chip_t *chip = snd_pcm_substream_chip(substream);
-+ struct snd_pcm_runtime *runtime = substream->runtime;
-+ bcm2835_alsa_stream_t *alsa_stream;
-+ int idx;
-+ int err;
-+
-+ audio_info(" .. IN (%d)\n", substream->number);
-+
-+ if(mutex_lock_interruptible(&chip->audio_mutex))
-+ {
-+ audio_error("Interrupted whilst waiting for lock\n");
-+ return -EINTR;
-+ }
-+ audio_info("Alsa open (%d)\n", substream->number);
-+ idx = substream->number;
-+
-+ if (spdif && chip->opened != 0) {
-+ err = -EBUSY;
-+ goto out;
-+ }
-+ else if (!spdif && (chip->opened & (1 << idx))) {
-+ err = -EBUSY;
-+ goto out;
-+ }
-+ if (idx > MAX_SUBSTREAMS) {
-+ audio_error
-+ ("substream(%d) device doesn't exist max(%d) substreams allowed\n",
-+ idx, MAX_SUBSTREAMS);
-+ err = -ENODEV;
-+ goto out;
-+ }
-+
-+ /* Check if we are ready */
-+ if (!(chip->avail_substreams & (1 << idx))) {
-+ /* We are not ready yet */
-+ audio_error("substream(%d) device is not ready yet\n", idx);
-+ err = -EAGAIN;
-+ goto out;
-+ }
-+
-+ alsa_stream = kzalloc(sizeof(bcm2835_alsa_stream_t), GFP_KERNEL);
-+ if (alsa_stream == NULL) {
-+ err = -ENOMEM;
-+ goto out;
-+ }
-+
-+ /* Initialise alsa_stream */
-+ alsa_stream->chip = chip;
-+ alsa_stream->substream = substream;
-+ alsa_stream->idx = idx;
-+
-+ sema_init(&alsa_stream->buffers_update_sem, 0);
-+ sema_init(&alsa_stream->control_sem, 0);
-+ spin_lock_init(&alsa_stream->lock);
-+
-+ /* Enabled in start trigger, called on each "fifo irq" after that */
-+ alsa_stream->enable_fifo_irq = 0;
-+ alsa_stream->fifo_irq_handler = bcm2835_playback_fifo_irq;
-+
-+ err = bcm2835_audio_open(alsa_stream);
-+ if (err != 0) {
-+ kfree(alsa_stream);
-+ goto out;
-+ }
-+ runtime->private_data = alsa_stream;
-+ runtime->private_free = snd_bcm2835_playback_free;
-+ if (spdif) {
-+ runtime->hw = snd_bcm2835_playback_spdif_hw;
-+ } else {
-+ /* clear spdif status, as we are not in spdif mode */
-+ chip->spdif_status = 0;
-+ runtime->hw = snd_bcm2835_playback_hw;
-+ }
-+ /* minimum 16 bytes alignment (for vchiq bulk transfers) */
-+ snd_pcm_hw_constraint_step(runtime, 0, SNDRV_PCM_HW_PARAM_PERIOD_BYTES,
-+ 16);
-+
-+ chip->alsa_stream[idx] = alsa_stream;
-+
-+ chip->opened |= (1 << idx);
-+ alsa_stream->open = 1;
-+ alsa_stream->draining = 1;
-+
-+out:
-+ mutex_unlock(&chip->audio_mutex);
-+
-+ audio_info(" .. OUT =%d\n", err);
-+
-+ return err;
-+}
-+
-+static int snd_bcm2835_playback_open(struct snd_pcm_substream *substream)
-+{
-+ return snd_bcm2835_playback_open_generic(substream, 0);
-+}
-+
-+static int snd_bcm2835_playback_spdif_open(struct snd_pcm_substream *substream)
-+{
-+ return snd_bcm2835_playback_open_generic(substream, 1);
-+}
-+
-+/* close callback */
-+static int snd_bcm2835_playback_close(struct snd_pcm_substream *substream)
-+{
-+ /* the hardware-specific codes will be here */
-+
-+ bcm2835_chip_t *chip;
-+ struct snd_pcm_runtime *runtime;
-+ bcm2835_alsa_stream_t *alsa_stream;
-+
-+ audio_info(" .. IN\n");
-+
-+ chip = snd_pcm_substream_chip(substream);
-+ if(mutex_lock_interruptible(&chip->audio_mutex))
-+ {
-+ audio_error("Interrupted whilst waiting for lock\n");
-+ return -EINTR;
-+ }
-+ runtime = substream->runtime;
-+ alsa_stream = runtime->private_data;
-+
-+ audio_info("Alsa close\n");
-+
-+ /*
-+ * Call stop if it's still running. This happens when app
-+ * is force killed and we don't get a stop trigger.
-+ */
-+ if (alsa_stream->running) {
-+ int err;
-+ err = bcm2835_audio_stop(alsa_stream);
-+ alsa_stream->running = 0;
-+ if (err != 0)
-+ audio_error(" Failed to STOP alsa device\n");
-+ }
-+
-+ alsa_stream->period_size = 0;
-+ alsa_stream->buffer_size = 0;
-+
-+ if (alsa_stream->open) {
-+ alsa_stream->open = 0;
-+ bcm2835_audio_close(alsa_stream);
-+ }
-+ if (alsa_stream->chip)
-+ alsa_stream->chip->alsa_stream[alsa_stream->idx] = NULL;
-+ /*
-+ * Do not free up alsa_stream here, it will be freed up by
-+ * runtime->private_free callback we registered in *_open above
-+ */
-+
-+ chip->opened &= ~(1 << substream->number);
-+
-+ mutex_unlock(&chip->audio_mutex);
-+ audio_info(" .. OUT\n");
-+
-+ return 0;
-+}
-+
-+/* hw_params callback */
-+static int snd_bcm2835_pcm_hw_params(struct snd_pcm_substream *substream,
-+ struct snd_pcm_hw_params *params)
-+{
-+ struct snd_pcm_runtime *runtime = substream->runtime;
-+ bcm2835_alsa_stream_t *alsa_stream = runtime->private_data;
-+ int err;
-+
-+ audio_info(" .. IN\n");
-+
-+ err = snd_pcm_lib_malloc_pages(substream, params_buffer_bytes(params));
-+ if (err < 0) {
-+ audio_error
-+ (" pcm_lib_malloc failed to allocated pages for buffers\n");
-+ return err;
-+ }
-+
-+ alsa_stream->channels = params_channels(params);
-+ alsa_stream->params_rate = params_rate(params);
-+ alsa_stream->pcm_format_width = snd_pcm_format_width(params_format (params));
-+ audio_info(" .. OUT\n");
-+
-+ return err;
-+}
-+
-+/* hw_free callback */
-+static int snd_bcm2835_pcm_hw_free(struct snd_pcm_substream *substream)
-+{
-+ audio_info(" .. IN\n");
-+ return snd_pcm_lib_free_pages(substream);
-+}
-+
-+/* prepare callback */
-+static int snd_bcm2835_pcm_prepare(struct snd_pcm_substream *substream)
-+{
-+ bcm2835_chip_t *chip = snd_pcm_substream_chip(substream);
-+ struct snd_pcm_runtime *runtime = substream->runtime;
-+ bcm2835_alsa_stream_t *alsa_stream = runtime->private_data;
-+ int channels;
-+ int err;
-+
-+ audio_info(" .. IN\n");
-+
-+ /* notify the vchiq that it should enter spdif passthrough mode by
-+ * setting channels=0 (see
-+ * https://github.com/raspberrypi/linux/issues/528) */
-+ if (chip->spdif_status & IEC958_AES0_NONAUDIO)
-+ channels = 0;
-+ else
-+ channels = alsa_stream->channels;
-+
-+ err = bcm2835_audio_set_params(alsa_stream, channels,
-+ alsa_stream->params_rate,
-+ alsa_stream->pcm_format_width);
-+ if (err < 0) {
-+ audio_error(" error setting hw params\n");
-+ }
-+
-+ bcm2835_audio_setup(alsa_stream);
-+
-+ /* in preparation of the stream, set the controls (volume level) of the stream */
-+ bcm2835_audio_set_ctls(alsa_stream->chip);
-+
-+
-+ memset(&alsa_stream->pcm_indirect, 0, sizeof(alsa_stream->pcm_indirect));
-+
-+ alsa_stream->pcm_indirect.hw_buffer_size =
-+ alsa_stream->pcm_indirect.sw_buffer_size =
-+ snd_pcm_lib_buffer_bytes(substream);
-+
-+ alsa_stream->buffer_size = snd_pcm_lib_buffer_bytes(substream);
-+ alsa_stream->period_size = snd_pcm_lib_period_bytes(substream);
-+ alsa_stream->pos = 0;
-+
-+ audio_debug("buffer_size=%d, period_size=%d pos=%d frame_bits=%d\n",
-+ alsa_stream->buffer_size, alsa_stream->period_size,
-+ alsa_stream->pos, runtime->frame_bits);
-+
-+ audio_info(" .. OUT\n");
-+ return 0;
-+}
-+
-+static void snd_bcm2835_pcm_transfer(struct snd_pcm_substream *substream,
-+ struct snd_pcm_indirect *rec, size_t bytes)
-+{
-+ struct snd_pcm_runtime *runtime = substream->runtime;
-+ bcm2835_alsa_stream_t *alsa_stream = runtime->private_data;
-+ void *src = (void *)(substream->runtime->dma_area + rec->sw_data);
-+ int err;
-+
-+ err = bcm2835_audio_write(alsa_stream, bytes, src);
-+ if (err)
-+ audio_error(" Failed to transfer to alsa device (%d)\n", err);
-+
-+}
-+
-+static int snd_bcm2835_pcm_ack(struct snd_pcm_substream *substream)
-+{
-+ struct snd_pcm_runtime *runtime = substream->runtime;
-+ bcm2835_alsa_stream_t *alsa_stream = runtime->private_data;
-+ struct snd_pcm_indirect *pcm_indirect = &alsa_stream->pcm_indirect;
-+
-+ pcm_indirect->hw_queue_size = runtime->hw.buffer_bytes_max;
-+ snd_pcm_indirect_playback_transfer(substream, pcm_indirect,
-+ snd_bcm2835_pcm_transfer);
-+ return 0;
-+}
-+
-+/* trigger callback */
-+static int snd_bcm2835_pcm_trigger(struct snd_pcm_substream *substream, int cmd)
-+{
-+ struct snd_pcm_runtime *runtime = substream->runtime;
-+ bcm2835_alsa_stream_t *alsa_stream = runtime->private_data;
-+ int err = 0;
-+
-+ audio_info(" .. IN\n");
-+
-+ switch (cmd) {
-+ case SNDRV_PCM_TRIGGER_START:
-+ audio_debug("bcm2835_AUDIO_TRIGGER_START running=%d\n",
-+ alsa_stream->running);
-+ if (!alsa_stream->running) {
-+ err = bcm2835_audio_start(alsa_stream);
-+ if (err == 0) {
-+ alsa_stream->pcm_indirect.hw_io =
-+ alsa_stream->pcm_indirect.hw_data =
-+ bytes_to_frames(runtime,
-+ alsa_stream->pos);
-+ substream->ops->ack(substream);
-+ alsa_stream->running = 1;
-+ alsa_stream->draining = 1;
-+ } else {
-+ audio_error(" Failed to START alsa device (%d)\n", err);
-+ }
-+ }
-+ break;
-+ case SNDRV_PCM_TRIGGER_STOP:
-+ audio_debug
-+ ("bcm2835_AUDIO_TRIGGER_STOP running=%d draining=%d\n",
-+ alsa_stream->running, runtime->status->state == SNDRV_PCM_STATE_DRAINING);
-+ if (runtime->status->state == SNDRV_PCM_STATE_DRAINING) {
-+ audio_info("DRAINING\n");
-+ alsa_stream->draining = 1;
-+ } else {
-+ audio_info("DROPPING\n");
-+ alsa_stream->draining = 0;
-+ }
-+ if (alsa_stream->running) {
-+ err = bcm2835_audio_stop(alsa_stream);
-+ if (err != 0)
-+ audio_error(" Failed to STOP alsa device (%d)\n", err);
-+ alsa_stream->running = 0;
-+ }
-+ break;
-+ default:
-+ err = -EINVAL;
-+ }
-+
-+ audio_info(" .. OUT\n");
-+ return err;
-+}
-+
-+/* pointer callback */
-+static snd_pcm_uframes_t
-+snd_bcm2835_pcm_pointer(struct snd_pcm_substream *substream)
-+{
-+ struct snd_pcm_runtime *runtime = substream->runtime;
-+ bcm2835_alsa_stream_t *alsa_stream = runtime->private_data;
-+
-+ audio_info(" .. IN\n");
-+
-+ audio_debug("pcm_pointer... (%d) hwptr=%d appl=%d pos=%d\n", 0,
-+ frames_to_bytes(runtime, runtime->status->hw_ptr),
-+ frames_to_bytes(runtime, runtime->control->appl_ptr),
-+ alsa_stream->pos);
-+
-+ audio_info(" .. OUT\n");
-+ return snd_pcm_indirect_playback_pointer(substream,
-+ &alsa_stream->pcm_indirect,
-+ alsa_stream->pos);
-+}
-+
-+static int snd_bcm2835_pcm_lib_ioctl(struct snd_pcm_substream *substream,
-+ unsigned int cmd, void *arg)
-+{
-+ int ret = snd_pcm_lib_ioctl(substream, cmd, arg);
-+ audio_info(" .. substream=%p, cmd=%d, arg=%p (%x) ret=%d\n", substream,
-+ cmd, arg, arg ? *(unsigned *)arg : 0, ret);
-+ return ret;
-+}
-+
-+/* operators */
-+static struct snd_pcm_ops snd_bcm2835_playback_ops = {
-+ .open = snd_bcm2835_playback_open,
-+ .close = snd_bcm2835_playback_close,
-+ .ioctl = snd_bcm2835_pcm_lib_ioctl,
-+ .hw_params = snd_bcm2835_pcm_hw_params,
-+ .hw_free = snd_bcm2835_pcm_hw_free,
-+ .prepare = snd_bcm2835_pcm_prepare,
-+ .trigger = snd_bcm2835_pcm_trigger,
-+ .pointer = snd_bcm2835_pcm_pointer,
-+ .ack = snd_bcm2835_pcm_ack,
-+};
-+
-+static struct snd_pcm_ops snd_bcm2835_playback_spdif_ops = {
-+ .open = snd_bcm2835_playback_spdif_open,
-+ .close = snd_bcm2835_playback_close,
-+ .ioctl = snd_bcm2835_pcm_lib_ioctl,
-+ .hw_params = snd_bcm2835_pcm_hw_params,
-+ .hw_free = snd_bcm2835_pcm_hw_free,
-+ .prepare = snd_bcm2835_pcm_prepare,
-+ .trigger = snd_bcm2835_pcm_trigger,
-+ .pointer = snd_bcm2835_pcm_pointer,
-+ .ack = snd_bcm2835_pcm_ack,
-+};
-+
-+/* create a pcm device */
-+int snd_bcm2835_new_pcm(bcm2835_chip_t * chip)
-+{
-+ struct snd_pcm *pcm;
-+ int err;
-+
-+ audio_info(" .. IN\n");
-+ mutex_init(&chip->audio_mutex);
-+ if(mutex_lock_interruptible(&chip->audio_mutex))
-+ {
-+ audio_error("Interrupted whilst waiting for lock\n");
-+ return -EINTR;
-+ }
-+ err =
-+ snd_pcm_new(chip->card, "bcm2835 ALSA", 0, MAX_SUBSTREAMS, 0, &pcm);
-+ if (err < 0)
-+ goto out;
-+ pcm->private_data = chip;
-+ strcpy(pcm->name, "bcm2835 ALSA");
-+ chip->pcm = pcm;
-+ chip->dest = AUDIO_DEST_AUTO;
-+ chip->volume = alsa2chip(0);
-+ chip->mute = CTRL_VOL_UNMUTE; /*disable mute on startup */
-+ /* set operators */
-+ snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_PLAYBACK,
-+ &snd_bcm2835_playback_ops);
-+
-+ /* pre-allocation of buffers */
-+ /* NOTE: this may fail */
-+ snd_pcm_lib_preallocate_pages_for_all(pcm, SNDRV_DMA_TYPE_CONTINUOUS,
-+ snd_dma_continuous_data
-+ (GFP_KERNEL), 64 * 1024,
-+ 64 * 1024);
-+
-+out:
-+ mutex_unlock(&chip->audio_mutex);
-+ audio_info(" .. OUT\n");
-+
-+ return 0;
-+}
-+
-+int snd_bcm2835_new_spdif_pcm(bcm2835_chip_t * chip)
-+{
-+ struct snd_pcm *pcm;
-+ int err;
-+
-+ audio_info(" .. IN\n");
-+ if(mutex_lock_interruptible(&chip->audio_mutex))
-+ {
-+ audio_error("Interrupted whilst waiting for lock\n");
-+ return -EINTR;
-+ }
-+ err = snd_pcm_new(chip->card, "bcm2835 ALSA", 1, 1, 0, &pcm);
-+ if (err < 0)
-+ goto out;
-+
-+ pcm->private_data = chip;
-+ strcpy(pcm->name, "bcm2835 IEC958/HDMI");
-+ chip->pcm_spdif = pcm;
-+ snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_PLAYBACK,
-+ &snd_bcm2835_playback_spdif_ops);
-+
-+ snd_pcm_lib_preallocate_pages_for_all(pcm, SNDRV_DMA_TYPE_CONTINUOUS,
-+ snd_dma_continuous_data (GFP_KERNEL),
-+ 64 * 1024, 64 * 1024);
-+out:
-+ mutex_unlock(&chip->audio_mutex);
-+ audio_info(" .. OUT\n");
-+
-+ return 0;
-+}
---- /dev/null
-+++ b/sound/arm/bcm2835-vchiq.c
-@@ -0,0 +1,902 @@
-+/*****************************************************************************
-+* Copyright 2011 Broadcom Corporation. All rights reserved.
-+*
-+* Unless you and Broadcom execute a separate written software license
-+* agreement governing use of this software, this software is licensed to you
-+* under the terms of the GNU General Public License version 2, available at
-+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
-+*
-+* Notwithstanding the above, under no circumstances may you combine this
-+* software in any way with any other Broadcom software provided under a
-+* license other than the GPL, without Broadcom's express prior written
-+* consent.
-+*****************************************************************************/
-+
-+#include <linux/device.h>
-+#include <sound/core.h>
-+#include <sound/initval.h>
-+#include <sound/pcm.h>
-+#include <linux/io.h>
-+#include <linux/interrupt.h>
-+#include <linux/fs.h>
-+#include <linux/file.h>
-+#include <linux/mm.h>
-+#include <linux/syscalls.h>
-+#include <asm/uaccess.h>
-+#include <linux/slab.h>
-+#include <linux/delay.h>
-+#include <linux/atomic.h>
-+#include <linux/module.h>
-+#include <linux/completion.h>
-+
-+#include "bcm2835.h"
-+
-+/* ---- Include Files -------------------------------------------------------- */
-+
-+#include "interface/vchi/vchi.h"
-+#include "vc_vchi_audioserv_defs.h"
-+
-+/* ---- Private Constants and Types ------------------------------------------ */
-+
-+#define BCM2835_AUDIO_STOP 0
-+#define BCM2835_AUDIO_START 1
-+#define BCM2835_AUDIO_WRITE 2
-+
-+/* Logging macros (for remapping to other logging mechanisms, i.e., printf) */
-+#ifdef AUDIO_DEBUG_ENABLE
-+ #define LOG_ERR( fmt, arg... ) pr_err( "%s:%d " fmt, __func__, __LINE__, ##arg)
-+ #define LOG_WARN( fmt, arg... ) pr_info( "%s:%d " fmt, __func__, __LINE__, ##arg)
-+ #define LOG_INFO( fmt, arg... ) pr_info( "%s:%d " fmt, __func__, __LINE__, ##arg)
-+ #define LOG_DBG( fmt, arg... ) pr_info( "%s:%d " fmt, __func__, __LINE__, ##arg)
-+#else
-+ #define LOG_ERR( fmt, arg... ) pr_err( "%s:%d " fmt, __func__, __LINE__, ##arg)
-+ #define LOG_WARN( fmt, arg... )
-+ #define LOG_INFO( fmt, arg... )
-+ #define LOG_DBG( fmt, arg... )
-+#endif
-+
-+typedef struct opaque_AUDIO_INSTANCE_T {
-+ uint32_t num_connections;
-+ VCHI_SERVICE_HANDLE_T vchi_handle[VCHI_MAX_NUM_CONNECTIONS];
-+ struct completion msg_avail_comp;
-+ struct mutex vchi_mutex;
-+ bcm2835_alsa_stream_t *alsa_stream;
-+ int32_t result;
-+ short peer_version;
-+} AUDIO_INSTANCE_T;
-+
-+bool force_bulk = false;
-+
-+/* ---- Private Variables ---------------------------------------------------- */
-+
-+/* ---- Private Function Prototypes ------------------------------------------ */
-+
-+/* ---- Private Functions ---------------------------------------------------- */
-+
-+static int bcm2835_audio_stop_worker(bcm2835_alsa_stream_t * alsa_stream);
-+static int bcm2835_audio_start_worker(bcm2835_alsa_stream_t * alsa_stream);
-+static int bcm2835_audio_write_worker(bcm2835_alsa_stream_t *alsa_stream,
-+ uint32_t count, void *src);
-+
-+typedef struct {
-+ struct work_struct my_work;
-+ bcm2835_alsa_stream_t *alsa_stream;
-+ int cmd;
-+ void *src;
-+ uint32_t count;
-+} my_work_t;
-+
-+static void my_wq_function(struct work_struct *work)
-+{
-+ my_work_t *w = (my_work_t *) work;
-+ int ret = -9;
-+ LOG_DBG(" .. IN %p:%d\n", w->alsa_stream, w->cmd);
-+ switch (w->cmd) {
-+ case BCM2835_AUDIO_START:
-+ ret = bcm2835_audio_start_worker(w->alsa_stream);
-+ break;
-+ case BCM2835_AUDIO_STOP:
-+ ret = bcm2835_audio_stop_worker(w->alsa_stream);
-+ break;
-+ case BCM2835_AUDIO_WRITE:
-+ ret = bcm2835_audio_write_worker(w->alsa_stream, w->count,
-+ w->src);
-+ break;
-+ default:
-+ LOG_ERR(" Unexpected work: %p:%d\n", w->alsa_stream, w->cmd);
-+ break;
-+ }
-+ kfree((void *)work);
-+ LOG_DBG(" .. OUT %d\n", ret);
-+}
-+
-+int bcm2835_audio_start(bcm2835_alsa_stream_t * alsa_stream)
-+{
-+ int ret = -1;
-+ LOG_DBG(" .. IN\n");
-+ if (alsa_stream->my_wq) {
-+ my_work_t *work = kmalloc(sizeof(my_work_t), GFP_ATOMIC);
-+ /*--- Queue some work (item 1) ---*/
-+ if (work) {
-+ INIT_WORK((struct work_struct *)work, my_wq_function);
-+ work->alsa_stream = alsa_stream;
-+ work->cmd = BCM2835_AUDIO_START;
-+ if (queue_work
-+ (alsa_stream->my_wq, (struct work_struct *)work))
-+ ret = 0;
-+ } else
-+ LOG_ERR(" .. Error: NULL work kmalloc\n");
-+ }
-+ LOG_DBG(" .. OUT %d\n", ret);
-+ return ret;
-+}
-+
-+int bcm2835_audio_stop(bcm2835_alsa_stream_t * alsa_stream)
-+{
-+ int ret = -1;
-+ LOG_DBG(" .. IN\n");
-+ if (alsa_stream->my_wq) {
-+ my_work_t *work = kmalloc(sizeof(my_work_t), GFP_ATOMIC);
-+ /*--- Queue some work (item 1) ---*/
-+ if (work) {
-+ INIT_WORK((struct work_struct *)work, my_wq_function);
-+ work->alsa_stream = alsa_stream;
-+ work->cmd = BCM2835_AUDIO_STOP;
-+ if (queue_work
-+ (alsa_stream->my_wq, (struct work_struct *)work))
-+ ret = 0;
-+ } else
-+ LOG_ERR(" .. Error: NULL work kmalloc\n");
-+ }
-+ LOG_DBG(" .. OUT %d\n", ret);
-+ return ret;
-+}
-+
-+int bcm2835_audio_write(bcm2835_alsa_stream_t *alsa_stream,
-+ uint32_t count, void *src)
-+{
-+ int ret = -1;
-+ LOG_DBG(" .. IN\n");
-+ if (alsa_stream->my_wq) {
-+ my_work_t *work = kmalloc(sizeof(my_work_t), GFP_ATOMIC);
-+ /*--- Queue some work (item 1) ---*/
-+ if (work) {
-+ INIT_WORK((struct work_struct *)work, my_wq_function);
-+ work->alsa_stream = alsa_stream;
-+ work->cmd = BCM2835_AUDIO_WRITE;
-+ work->src = src;
-+ work->count = count;
-+ if (queue_work
-+ (alsa_stream->my_wq, (struct work_struct *)work))
-+ ret = 0;
-+ } else
-+ LOG_ERR(" .. Error: NULL work kmalloc\n");
-+ }
-+ LOG_DBG(" .. OUT %d\n", ret);
-+ return ret;
-+}
-+
-+void my_workqueue_init(bcm2835_alsa_stream_t * alsa_stream)
-+{
-+ alsa_stream->my_wq = alloc_workqueue("my_queue", WQ_HIGHPRI, 1);
-+ return;
-+}
-+
-+void my_workqueue_quit(bcm2835_alsa_stream_t * alsa_stream)
-+{
-+ if (alsa_stream->my_wq) {
-+ flush_workqueue(alsa_stream->my_wq);
-+ destroy_workqueue(alsa_stream->my_wq);
-+ alsa_stream->my_wq = NULL;
-+ }
-+ return;
-+}
-+
-+static void audio_vchi_callback(void *param,
-+ const VCHI_CALLBACK_REASON_T reason,
-+ void *msg_handle)
-+{
-+ AUDIO_INSTANCE_T *instance = (AUDIO_INSTANCE_T *) param;
-+ int32_t status;
-+ int32_t msg_len;
-+ VC_AUDIO_MSG_T m;
-+ LOG_DBG(" .. IN instance=%p, handle=%p, alsa=%p, reason=%d, handle=%p\n",
-+ instance, instance ? instance->vchi_handle[0] : NULL, instance ? instance->alsa_stream : NULL, reason, msg_handle);
-+
-+ if (reason != VCHI_CALLBACK_MSG_AVAILABLE) {
-+ return;
-+ }
-+ if (!instance) {
-+ LOG_ERR(" .. instance is null\n");
-+ BUG();
-+ return;
-+ }
-+ if (!instance->vchi_handle[0]) {
-+ LOG_ERR(" .. instance->vchi_handle[0] is null\n");
-+ BUG();
-+ return;
-+ }
-+ status = vchi_msg_dequeue(instance->vchi_handle[0],
-+ &m, sizeof m, &msg_len, VCHI_FLAGS_NONE);
-+ if (m.type == VC_AUDIO_MSG_TYPE_RESULT) {
-+ LOG_DBG
-+ (" .. instance=%p, m.type=VC_AUDIO_MSG_TYPE_RESULT, success=%d\n",
-+ instance, m.u.result.success);
-+ instance->result = m.u.result.success;
-+ complete(&instance->msg_avail_comp);
-+ } else if (m.type == VC_AUDIO_MSG_TYPE_COMPLETE) {
-+ bcm2835_alsa_stream_t *alsa_stream = instance->alsa_stream;
-+ irq_handler_t callback = (irq_handler_t) m.u.complete.callback;
-+ LOG_DBG
-+ (" .. instance=%p, m.type=VC_AUDIO_MSG_TYPE_COMPLETE, complete=%d\n",
-+ instance, m.u.complete.count);
-+ if (alsa_stream && callback) {
-+ atomic_add(m.u.complete.count, &alsa_stream->retrieved);
-+ callback(0, alsa_stream);
-+ } else {
-+ LOG_ERR(" .. unexpected alsa_stream=%p, callback=%p\n",
-+ alsa_stream, callback);
-+ }
-+ } else {
-+ LOG_ERR(" .. unexpected m.type=%d\n", m.type);
-+ }
-+ LOG_DBG(" .. OUT\n");
-+}
-+
-+static AUDIO_INSTANCE_T *vc_vchi_audio_init(VCHI_INSTANCE_T vchi_instance,
-+ VCHI_CONNECTION_T **
-+ vchi_connections,
-+ uint32_t num_connections)
-+{
-+ uint32_t i;
-+ AUDIO_INSTANCE_T *instance;
-+ int status;
-+
-+ LOG_DBG("%s: start", __func__);
-+
-+ if (num_connections > VCHI_MAX_NUM_CONNECTIONS) {
-+ LOG_ERR("%s: unsupported number of connections %u (max=%u)\n",
-+ __func__, num_connections, VCHI_MAX_NUM_CONNECTIONS);
-+
-+ return NULL;
-+ }
-+ /* Allocate memory for this instance */
-+ instance = kmalloc(sizeof(*instance), GFP_KERNEL);
-+ if (!instance)
-+ return NULL;
-+
-+ memset(instance, 0, sizeof(*instance));
-+ instance->num_connections = num_connections;
-+
-+ /* Create a lock for exclusive, serialized VCHI connection access */
-+ mutex_init(&instance->vchi_mutex);
-+ /* Open the VCHI service connections */
-+ for (i = 0; i < num_connections; i++) {
-+ SERVICE_CREATION_T params = {
-+ VCHI_VERSION_EX(VC_AUDIOSERV_VER, VC_AUDIOSERV_MIN_VER),
-+ VC_AUDIO_SERVER_NAME, // 4cc service code
-+ vchi_connections[i], // passed in fn pointers
-+ 0, // rx fifo size (unused)
-+ 0, // tx fifo size (unused)
-+ audio_vchi_callback, // service callback
-+ instance, // service callback parameter
-+ 1, //TODO: remove VCOS_FALSE, // unaligned bulk recieves
-+ 1, //TODO: remove VCOS_FALSE, // unaligned bulk transmits
-+ 0 // want crc check on bulk transfers
-+ };
-+
-+ LOG_DBG("%s: about to open %i\n", __func__, i);
-+ status = vchi_service_open(vchi_instance, ¶ms,
-+ &instance->vchi_handle[i]);
-+ LOG_DBG("%s: opened %i: %p=%d\n", __func__, i, instance->vchi_handle[i], status);
-+ if (status) {
-+ LOG_ERR
-+ ("%s: failed to open VCHI service connection (status=%d)\n",
-+ __func__, status);
-+
-+ goto err_close_services;
-+ }
-+ /* Finished with the service for now */
-+ vchi_service_release(instance->vchi_handle[i]);
-+ }
-+
-+ LOG_DBG("%s: okay\n", __func__);
-+ return instance;
-+
-+err_close_services:
-+ for (i = 0; i < instance->num_connections; i++) {
-+ LOG_ERR("%s: closing %i: %p\n", __func__, i, instance->vchi_handle[i]);
-+ if (instance->vchi_handle[i])
-+ vchi_service_close(instance->vchi_handle[i]);
-+ }
-+
-+ kfree(instance);
-+ LOG_ERR("%s: error\n", __func__);
-+
-+ return NULL;
-+}
-+
-+static int32_t vc_vchi_audio_deinit(AUDIO_INSTANCE_T * instance)
-+{
-+ uint32_t i;
-+
-+ LOG_DBG(" .. IN\n");
-+
-+ if (instance == NULL) {
-+ LOG_ERR("%s: invalid handle %p\n", __func__, instance);
-+
-+ return -1;
-+ }
-+
-+ LOG_DBG(" .. about to lock (%d)\n", instance->num_connections);
-+ if(mutex_lock_interruptible(&instance->vchi_mutex))
-+ {
-+ LOG_DBG("Interrupted whilst waiting for lock on (%d)\n",instance->num_connections);
-+ return -EINTR;
-+ }
-+
-+ /* Close all VCHI service connections */
-+ for (i = 0; i < instance->num_connections; i++) {
-+ int32_t success;
-+ LOG_DBG(" .. %i:closing %p\n", i, instance->vchi_handle[i]);
-+ vchi_service_use(instance->vchi_handle[i]);
-+
-+ success = vchi_service_close(instance->vchi_handle[i]);
-+ if (success != 0) {
-+ LOG_DBG
-+ ("%s: failed to close VCHI service connection (status=%d)\n",
-+ __func__, success);
-+ }
-+ }
-+
-+ mutex_unlock(&instance->vchi_mutex);
-+
-+ kfree(instance);
-+
-+ LOG_DBG(" .. OUT\n");
-+
-+ return 0;
-+}
-+
-+static int bcm2835_audio_open_connection(bcm2835_alsa_stream_t * alsa_stream)
-+{
-+ static VCHI_INSTANCE_T vchi_instance;
-+ static VCHI_CONNECTION_T *vchi_connection;
-+ static int initted;
-+ AUDIO_INSTANCE_T *instance = alsa_stream->instance;
-+ int ret;
-+ LOG_DBG(" .. IN\n");
-+
-+ LOG_INFO("%s: start\n", __func__);
-+ BUG_ON(instance);
-+ if (instance) {
-+ LOG_ERR("%s: VCHI instance already open (%p)\n",
-+ __func__, instance);
-+ instance->alsa_stream = alsa_stream;
-+ alsa_stream->instance = instance;
-+ ret = 0; // xxx todo -1;
-+ goto err_free_mem;
-+ }
-+
-+ /* Initialize and create a VCHI connection */
-+ if (!initted) {
-+ ret = vchi_initialise(&vchi_instance);
-+ if (ret != 0) {
-+ LOG_ERR("%s: failed to initialise VCHI instance (ret=%d)\n",
-+ __func__, ret);
-+
-+ ret = -EIO;
-+ goto err_free_mem;
-+ }
-+ ret = vchi_connect(NULL, 0, vchi_instance);
-+ if (ret != 0) {
-+ LOG_ERR("%s: failed to connect VCHI instance (ret=%d)\n",
-+ __func__, ret);
-+
-+ ret = -EIO;
-+ goto err_free_mem;
-+ }
-+ initted = 1;
-+ }
-+
-+ /* Initialize an instance of the audio service */
-+ instance = vc_vchi_audio_init(vchi_instance, &vchi_connection, 1);
-+
-+ if (instance == NULL) {
-+ LOG_ERR("%s: failed to initialize audio service\n", __func__);
-+
-+ ret = -EPERM;
-+ goto err_free_mem;
-+ }
-+
-+ instance->alsa_stream = alsa_stream;
-+ alsa_stream->instance = instance;
-+
-+ LOG_DBG(" success !\n");
-+err_free_mem:
-+ LOG_DBG(" .. OUT\n");
-+
-+ return ret;
-+}
-+
-+int bcm2835_audio_open(bcm2835_alsa_stream_t * alsa_stream)
-+{
-+ AUDIO_INSTANCE_T *instance;
-+ VC_AUDIO_MSG_T m;
-+ int32_t success;
-+ int ret;
-+ LOG_DBG(" .. IN\n");
-+
-+ my_workqueue_init(alsa_stream);
-+
-+ ret = bcm2835_audio_open_connection(alsa_stream);
-+ if (ret != 0) {
-+ ret = -1;
-+ goto exit;
-+ }
-+ instance = alsa_stream->instance;
-+ LOG_DBG(" instance (%p)\n", instance);
-+
-+ if(mutex_lock_interruptible(&instance->vchi_mutex))
-+ {
-+ LOG_DBG("Interrupted whilst waiting for lock on (%d)\n",instance->num_connections);
-+ return -EINTR;
-+ }
-+ vchi_service_use(instance->vchi_handle[0]);
-+
-+ m.type = VC_AUDIO_MSG_TYPE_OPEN;
-+
-+ /* Send the message to the videocore */
-+ success = vchi_msg_queue(instance->vchi_handle[0],
-+ &m, sizeof m,
-+ VCHI_FLAGS_BLOCK_UNTIL_QUEUED, NULL);
-+
-+ if (success != 0) {
-+ LOG_ERR("%s: failed on vchi_msg_queue (status=%d)\n",
-+ __func__, success);
-+
-+ ret = -1;
-+ goto unlock;
-+ }
-+
-+ ret = 0;
-+
-+unlock:
-+ vchi_service_release(instance->vchi_handle[0]);
-+ mutex_unlock(&instance->vchi_mutex);
-+exit:
-+ LOG_DBG(" .. OUT\n");
-+ return ret;
-+}
-+
-+static int bcm2835_audio_set_ctls_chan(bcm2835_alsa_stream_t * alsa_stream,
-+ bcm2835_chip_t * chip)
-+{
-+ VC_AUDIO_MSG_T m;
-+ AUDIO_INSTANCE_T *instance = alsa_stream->instance;
-+ int32_t success;
-+ int ret;
-+ LOG_DBG(" .. IN\n");
-+
-+ LOG_INFO
-+ (" Setting ALSA dest(%d), volume(%d)\n", chip->dest, chip->volume);
-+
-+ if(mutex_lock_interruptible(&instance->vchi_mutex))
-+ {
-+ LOG_DBG("Interrupted whilst waiting for lock on (%d)\n",instance->num_connections);
-+ return -EINTR;
-+ }
-+ vchi_service_use(instance->vchi_handle[0]);
-+
-+ instance->result = -1;
-+
-+ m.type = VC_AUDIO_MSG_TYPE_CONTROL;
-+ m.u.control.dest = chip->dest;
-+ m.u.control.volume = chip->volume;
-+
-+ /* Create the message available completion */
-+ init_completion(&instance->msg_avail_comp);
-+
-+ /* Send the message to the videocore */
-+ success = vchi_msg_queue(instance->vchi_handle[0],
-+ &m, sizeof m,
-+ VCHI_FLAGS_BLOCK_UNTIL_QUEUED, NULL);
-+
-+ if (success != 0) {
-+ LOG_ERR("%s: failed on vchi_msg_queue (status=%d)\n",
-+ __func__, success);
-+
-+ ret = -1;
-+ goto unlock;
-+ }
-+
-+ /* We are expecting a reply from the videocore */
-+ ret = wait_for_completion_interruptible(&instance->msg_avail_comp);
-+ if (ret) {
-+ LOG_DBG("%s: failed on waiting for event (status=%d)\n",
-+ __func__, success);
-+ goto unlock;
-+ }
-+
-+ if (instance->result != 0) {
-+ LOG_ERR("%s: result=%d\n", __func__, instance->result);
-+
-+ ret = -1;
-+ goto unlock;
-+ }
-+
-+ ret = 0;
-+
-+unlock:
-+ vchi_service_release(instance->vchi_handle[0]);
-+ mutex_unlock(&instance->vchi_mutex);
-+
-+ LOG_DBG(" .. OUT\n");
-+ return ret;
-+}
-+
-+int bcm2835_audio_set_ctls(bcm2835_chip_t * chip)
-+{
-+ int i;
-+ int ret = 0;
-+ LOG_DBG(" .. IN\n");
-+ LOG_DBG(" Setting ALSA dest(%d), volume(%d)\n", chip->dest, chip->volume);
-+
-+ /* change ctls for all substreams */
-+ for (i = 0; i < MAX_SUBSTREAMS; i++) {
-+ if (chip->avail_substreams & (1 << i)) {
-+ if (!chip->alsa_stream[i])
-+ {
-+ LOG_DBG(" No ALSA stream available?! %i:%p (%x)\n", i, chip->alsa_stream[i], chip->avail_substreams);
-+ ret = 0;
-+ }
-+ else if (bcm2835_audio_set_ctls_chan /* returns 0 on success */
-+ (chip->alsa_stream[i], chip) != 0)
-+ {
-+ LOG_ERR("Couldn't set the controls for stream %d\n", i);
-+ ret = -1;
-+ }
-+ else LOG_DBG(" Controls set for stream %d\n", i);
-+ }
-+ }
-+ LOG_DBG(" .. OUT ret=%d\n", ret);
-+ return ret;
-+}
-+
-+int bcm2835_audio_set_params(bcm2835_alsa_stream_t * alsa_stream,
-+ uint32_t channels, uint32_t samplerate,
-+ uint32_t bps)
-+{
-+ VC_AUDIO_MSG_T m;
-+ AUDIO_INSTANCE_T *instance = alsa_stream->instance;
-+ int32_t success;
-+ int ret;
-+ LOG_DBG(" .. IN\n");
-+
-+ LOG_INFO
-+ (" Setting ALSA channels(%d), samplerate(%d), bits-per-sample(%d)\n",
-+ channels, samplerate, bps);
-+
-+ /* resend ctls - alsa_stream may not have been open when first send */
-+ ret = bcm2835_audio_set_ctls_chan(alsa_stream, alsa_stream->chip);
-+ if (ret != 0) {
-+ LOG_ERR(" Alsa controls not supported\n");
-+ return -EINVAL;
-+ }
-+
-+ if(mutex_lock_interruptible(&instance->vchi_mutex))
-+ {
-+ LOG_DBG("Interrupted whilst waiting for lock on (%d)\n",instance->num_connections);
-+ return -EINTR;
-+ }
-+ vchi_service_use(instance->vchi_handle[0]);
-+
-+ instance->result = -1;
-+
-+ m.type = VC_AUDIO_MSG_TYPE_CONFIG;
-+ m.u.config.channels = channels;
-+ m.u.config.samplerate = samplerate;
-+ m.u.config.bps = bps;
-+
-+ /* Create the message available completion */
-+ init_completion(&instance->msg_avail_comp);
-+
-+ /* Send the message to the videocore */
-+ success = vchi_msg_queue(instance->vchi_handle[0],
-+ &m, sizeof m,
-+ VCHI_FLAGS_BLOCK_UNTIL_QUEUED, NULL);
-+
-+ if (success != 0) {
-+ LOG_ERR("%s: failed on vchi_msg_queue (status=%d)\n",
-+ __func__, success);
-+
-+ ret = -1;
-+ goto unlock;
-+ }
-+
-+ /* We are expecting a reply from the videocore */
-+ ret = wait_for_completion_interruptible(&instance->msg_avail_comp);
-+ if (ret) {
-+ LOG_DBG("%s: failed on waiting for event (status=%d)\n",
-+ __func__, success);
-+ goto unlock;
-+ }
-+
-+ if (instance->result != 0) {
-+ LOG_ERR("%s: result=%d", __func__, instance->result);
-+
-+ ret = -1;
-+ goto unlock;
-+ }
-+
-+ ret = 0;
-+
-+unlock:
-+ vchi_service_release(instance->vchi_handle[0]);
-+ mutex_unlock(&instance->vchi_mutex);
-+
-+ LOG_DBG(" .. OUT\n");
-+ return ret;
-+}
-+
-+int bcm2835_audio_setup(bcm2835_alsa_stream_t * alsa_stream)
-+{
-+ LOG_DBG(" .. IN\n");
-+
-+ LOG_DBG(" .. OUT\n");
-+
-+ return 0;
-+}
-+
-+static int bcm2835_audio_start_worker(bcm2835_alsa_stream_t * alsa_stream)
-+{
-+ VC_AUDIO_MSG_T m;
-+ AUDIO_INSTANCE_T *instance = alsa_stream->instance;
-+ int32_t success;
-+ int ret;
-+ LOG_DBG(" .. IN\n");
-+
-+ if(mutex_lock_interruptible(&instance->vchi_mutex))
-+ {
-+ LOG_DBG("Interrupted whilst waiting for lock on (%d)\n",instance->num_connections);
-+ return -EINTR;
-+ }
-+ vchi_service_use(instance->vchi_handle[0]);
-+
-+ m.type = VC_AUDIO_MSG_TYPE_START;
-+
-+ /* Send the message to the videocore */
-+ success = vchi_msg_queue(instance->vchi_handle[0],
-+ &m, sizeof m,
-+ VCHI_FLAGS_BLOCK_UNTIL_QUEUED, NULL);
-+
-+ if (success != 0) {
-+ LOG_ERR("%s: failed on vchi_msg_queue (status=%d)\n",
-+ __func__, success);
-+
-+ ret = -1;
-+ goto unlock;
-+ }
-+
-+ ret = 0;
-+
-+unlock:
-+ vchi_service_release(instance->vchi_handle[0]);
-+ mutex_unlock(&instance->vchi_mutex);
-+ LOG_DBG(" .. OUT\n");
-+ return ret;
-+}
-+
-+static int bcm2835_audio_stop_worker(bcm2835_alsa_stream_t * alsa_stream)
-+{
-+ VC_AUDIO_MSG_T m;
-+ AUDIO_INSTANCE_T *instance = alsa_stream->instance;
-+ int32_t success;
-+ int ret;
-+ LOG_DBG(" .. IN\n");
-+
-+ if(mutex_lock_interruptible(&instance->vchi_mutex))
-+ {
-+ LOG_DBG("Interrupted whilst waiting for lock on (%d)\n",instance->num_connections);
-+ return -EINTR;
-+ }
-+ vchi_service_use(instance->vchi_handle[0]);
-+
-+ m.type = VC_AUDIO_MSG_TYPE_STOP;
-+ m.u.stop.draining = alsa_stream->draining;
-+
-+ /* Send the message to the videocore */
-+ success = vchi_msg_queue(instance->vchi_handle[0],
-+ &m, sizeof m,
-+ VCHI_FLAGS_BLOCK_UNTIL_QUEUED, NULL);
-+
-+ if (success != 0) {
-+ LOG_ERR("%s: failed on vchi_msg_queue (status=%d)\n",
-+ __func__, success);
-+
-+ ret = -1;
-+ goto unlock;
-+ }
-+
-+ ret = 0;
-+
-+unlock:
-+ vchi_service_release(instance->vchi_handle[0]);
-+ mutex_unlock(&instance->vchi_mutex);
-+ LOG_DBG(" .. OUT\n");
-+ return ret;
-+}
-+
-+int bcm2835_audio_close(bcm2835_alsa_stream_t * alsa_stream)
-+{
-+ VC_AUDIO_MSG_T m;
-+ AUDIO_INSTANCE_T *instance = alsa_stream->instance;
-+ int32_t success;
-+ int ret;
-+ LOG_DBG(" .. IN\n");
-+
-+ my_workqueue_quit(alsa_stream);
-+
-+ if(mutex_lock_interruptible(&instance->vchi_mutex))
-+ {
-+ LOG_DBG("Interrupted whilst waiting for lock on (%d)\n",instance->num_connections);
-+ return -EINTR;
-+ }
-+ vchi_service_use(instance->vchi_handle[0]);
-+
-+ m.type = VC_AUDIO_MSG_TYPE_CLOSE;
-+
-+ /* Create the message available completion */
-+ init_completion(&instance->msg_avail_comp);
-+
-+ /* Send the message to the videocore */
-+ success = vchi_msg_queue(instance->vchi_handle[0],
-+ &m, sizeof m,
-+ VCHI_FLAGS_BLOCK_UNTIL_QUEUED, NULL);
-+
-+ if (success != 0) {
-+ LOG_ERR("%s: failed on vchi_msg_queue (status=%d)\n",
-+ __func__, success);
-+ ret = -1;
-+ goto unlock;
-+ }
-+
-+ ret = wait_for_completion_interruptible(&instance->msg_avail_comp);
-+ if (ret) {
-+ LOG_DBG("%s: failed on waiting for event (status=%d)\n",
-+ __func__, success);
-+ goto unlock;
-+ }
-+ if (instance->result != 0) {
-+ LOG_ERR("%s: failed result (status=%d)\n",
-+ __func__, instance->result);
-+
-+ ret = -1;
-+ goto unlock;
-+ }
-+
-+ ret = 0;
-+
-+unlock:
-+ vchi_service_release(instance->vchi_handle[0]);
-+ mutex_unlock(&instance->vchi_mutex);
-+
-+ /* Stop the audio service */
-+ if (instance) {
-+ vc_vchi_audio_deinit(instance);
-+ alsa_stream->instance = NULL;
-+ }
-+ LOG_DBG(" .. OUT\n");
-+ return ret;
-+}
-+
-+int bcm2835_audio_write_worker(bcm2835_alsa_stream_t *alsa_stream,
-+ uint32_t count, void *src)
-+{
-+ VC_AUDIO_MSG_T m;
-+ AUDIO_INSTANCE_T *instance = alsa_stream->instance;
-+ int32_t success;
-+ int ret;
-+
-+ LOG_DBG(" .. IN\n");
-+
-+ LOG_INFO(" Writing %d bytes from %p\n", count, src);
-+
-+ if(mutex_lock_interruptible(&instance->vchi_mutex))
-+ {
-+ LOG_DBG("Interrupted whilst waiting for lock on (%d)\n",instance->num_connections);
-+ return -EINTR;
-+ }
-+ vchi_service_use(instance->vchi_handle[0]);
-+
-+ if ( instance->peer_version==0 && vchi_get_peer_version(instance->vchi_handle[0], &instance->peer_version) == 0 ) {
-+ LOG_DBG("%s: client version %d connected\n", __func__, instance->peer_version);
-+ }
-+ m.type = VC_AUDIO_MSG_TYPE_WRITE;
-+ m.u.write.count = count;
-+ // old version uses bulk, new version uses control
-+ m.u.write.max_packet = instance->peer_version < 2 || force_bulk ? 0:4000;
-+ m.u.write.callback = alsa_stream->fifo_irq_handler;
-+ m.u.write.cookie = alsa_stream;
-+ m.u.write.silence = src == NULL;
-+
-+ /* Send the message to the videocore */
-+ success = vchi_msg_queue(instance->vchi_handle[0],
-+ &m, sizeof m,
-+ VCHI_FLAGS_BLOCK_UNTIL_QUEUED, NULL);
-+
-+ if (success != 0) {
-+ LOG_ERR("%s: failed on vchi_msg_queue (status=%d)\n",
-+ __func__, success);
-+
-+ ret = -1;
-+ goto unlock;
-+ }
-+ if (!m.u.write.silence) {
-+ if (m.u.write.max_packet == 0) {
-+ /* Send the message to the videocore */
-+ success = vchi_bulk_queue_transmit(instance->vchi_handle[0],
-+ src, count,
-+ 0 *
-+ VCHI_FLAGS_BLOCK_UNTIL_QUEUED
-+ +
-+ 1 *
-+ VCHI_FLAGS_BLOCK_UNTIL_DATA_READ,
-+ NULL);
-+ } else {
-+ while (count > 0) {
-+ int bytes = min((int)m.u.write.max_packet, (int)count);
-+ success = vchi_msg_queue(instance->vchi_handle[0],
-+ src, bytes,
-+ VCHI_FLAGS_BLOCK_UNTIL_QUEUED, NULL);
-+ src = (char *)src + bytes;
-+ count -= bytes;
-+ }
-+ }
-+ if (success != 0) {
-+ LOG_ERR
-+ ("%s: failed on vchi_bulk_queue_transmit (status=%d)\n",
-+ __func__, success);
-+
-+ ret = -1;
-+ goto unlock;
-+ }
-+ }
-+ ret = 0;
-+
-+unlock:
-+ vchi_service_release(instance->vchi_handle[0]);
-+ mutex_unlock(&instance->vchi_mutex);
-+ LOG_DBG(" .. OUT\n");
-+ return ret;
-+}
-+
-+/**
-+ * Returns all buffers from arm->vc
-+ */
-+void bcm2835_audio_flush_buffers(bcm2835_alsa_stream_t * alsa_stream)
-+{
-+ LOG_DBG(" .. IN\n");
-+ LOG_DBG(" .. OUT\n");
-+ return;
-+}
-+
-+/**
-+ * Forces VC to flush(drop) its filled playback buffers and
-+ * return them the us. (VC->ARM)
-+ */
-+void bcm2835_audio_flush_playback_buffers(bcm2835_alsa_stream_t * alsa_stream)
-+{
-+ LOG_DBG(" .. IN\n");
-+ LOG_DBG(" .. OUT\n");
-+}
-+
-+uint32_t bcm2835_audio_retrieve_buffers(bcm2835_alsa_stream_t * alsa_stream)
-+{
-+ uint32_t count = atomic_read(&alsa_stream->retrieved);
-+ atomic_sub(count, &alsa_stream->retrieved);
-+ return count;
-+}
-+
-+module_param(force_bulk, bool, 0444);
-+MODULE_PARM_DESC(force_bulk, "Force use of vchiq bulk for audio");
---- /dev/null
-+++ b/sound/arm/bcm2835.c
-@@ -0,0 +1,511 @@
-+/*****************************************************************************
-+* Copyright 2011 Broadcom Corporation. All rights reserved.
-+*
-+* Unless you and Broadcom execute a separate written software license
-+* agreement governing use of this software, this software is licensed to you
-+* under the terms of the GNU General Public License version 2, available at
-+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
-+*
-+* Notwithstanding the above, under no circumstances may you combine this
-+* software in any way with any other Broadcom software provided under a
-+* license other than the GPL, without Broadcom's express prior written
-+* consent.
-+*****************************************************************************/
-+
-+#include <linux/platform_device.h>
-+
-+#include <linux/init.h>
-+#include <linux/slab.h>
-+#include <linux/module.h>
-+#include <linux/of.h>
-+
-+#include "bcm2835.h"
-+
-+/* module parameters (see "Module Parameters") */
-+/* SNDRV_CARDS: maximum number of cards supported by this module */
-+static int index[MAX_SUBSTREAMS] = {[0 ... (MAX_SUBSTREAMS - 1)] = -1 };
-+static char *id[MAX_SUBSTREAMS] = {[0 ... (MAX_SUBSTREAMS - 1)] = NULL };
-+static int enable[MAX_SUBSTREAMS] = {[0 ... (MAX_SUBSTREAMS - 1)] = 1 };
-+
-+/* HACKY global pointers needed for successive probes to work : ssp
-+ * But compared against the changes we will have to do in VC audio_ipc code
-+ * to export 8 audio_ipc devices as a single IPC device and then monitor all
-+ * four devices in a thread, this gets things done quickly and should be easier
-+ * to debug if we run into issues
-+ */
-+
-+static struct snd_card *g_card = NULL;
-+static bcm2835_chip_t *g_chip = NULL;
-+
-+static int snd_bcm2835_free(bcm2835_chip_t * chip)
-+{
-+ kfree(chip);
-+ return 0;
-+}
-+
-+/* component-destructor
-+ * (see "Management of Cards and Components")
-+ */
-+static int snd_bcm2835_dev_free(struct snd_device *device)
-+{
-+ return snd_bcm2835_free(device->device_data);
-+}
-+
-+/* chip-specific constructor
-+ * (see "Management of Cards and Components")
-+ */
-+static int snd_bcm2835_create(struct snd_card *card,
-+ struct platform_device *pdev,
-+ bcm2835_chip_t ** rchip)
-+{
-+ bcm2835_chip_t *chip;
-+ int err;
-+ static struct snd_device_ops ops = {
-+ .dev_free = snd_bcm2835_dev_free,
-+ };
-+
-+ *rchip = NULL;
-+
-+ chip = kzalloc(sizeof(*chip), GFP_KERNEL);
-+ if (chip == NULL)
-+ return -ENOMEM;
-+
-+ chip->card = card;
-+
-+ err = snd_device_new(card, SNDRV_DEV_LOWLEVEL, chip, &ops);
-+ if (err < 0) {
-+ snd_bcm2835_free(chip);
-+ return err;
-+ }
-+
-+ *rchip = chip;
-+ return 0;
-+}
-+
-+static int snd_bcm2835_alsa_probe_dt(struct platform_device *pdev)
-+{
-+ struct device *dev = &pdev->dev;
-+ bcm2835_chip_t *chip;
-+ struct snd_card *card;
-+ u32 numchans;
-+ int err, i;
-+
-+ err = of_property_read_u32(dev->of_node, "brcm,pwm-channels",
-+ &numchans);
-+ if (err) {
-+ dev_err(dev, "Failed to get DT property 'brcm,pwm-channels'");
-+ return err;
-+ }
-+
-+ if (numchans == 0 || numchans > MAX_SUBSTREAMS) {
-+ numchans = MAX_SUBSTREAMS;
-+ dev_warn(dev, "Illegal 'brcm,pwm-channels' value, will use %u\n",
-+ numchans);
-+ }
-+
-+ err = snd_card_new(NULL, -1, NULL, THIS_MODULE, 0, &card);
-+ if (err) {
-+ dev_err(dev, "Failed to create soundcard structure\n");
-+ return err;
-+ }
-+
-+ snd_card_set_dev(card, dev);
-+ strcpy(card->driver, "bcm2835");
-+ strcpy(card->shortname, "bcm2835 ALSA");
-+ sprintf(card->longname, "%s", card->shortname);
-+
-+ err = snd_bcm2835_create(card, pdev, &chip);
-+ if (err < 0) {
-+ dev_err(dev, "Failed to create bcm2835 chip\n");
-+ goto err_free;
-+ }
-+
-+ err = snd_bcm2835_new_pcm(chip);
-+ if (err < 0) {
-+ dev_err(dev, "Failed to create new bcm2835 pcm device\n");
-+ goto err_free;
-+ }
-+
-+ err = snd_bcm2835_new_spdif_pcm(chip);
-+ if (err < 0) {
-+ dev_err(dev, "Failed to create new bcm2835 spdif pcm device\n");
-+ goto err_free;
-+ }
-+
-+ err = snd_bcm2835_new_ctl(chip);
-+ if (err < 0) {
-+ dev_err(dev, "Failed to create new bcm2835 ctl\n");
-+ goto err_free;
-+ }
-+
-+ for (i = 0; i < numchans; i++) {
-+ chip->avail_substreams |= (1 << i);
-+ chip->pdev[i] = pdev;
-+ }
-+
-+ err = snd_card_register(card);
-+ if (err) {
-+ dev_err(dev, "Failed to register bcm2835 ALSA card \n");
-+ goto err_free;
-+ }
-+
-+ g_card = card;
-+ g_chip = chip;
-+ platform_set_drvdata(pdev, card);
-+ audio_info("bcm2835 ALSA card created with %u channels\n", numchans);
-+
-+ return 0;
-+
-+err_free:
-+ snd_card_free(card);
-+
-+ return err;
-+}
-+
-+static int snd_bcm2835_alsa_probe(struct platform_device *pdev)
-+{
-+ static int dev;
-+ bcm2835_chip_t *chip;
-+ struct snd_card *card;
-+ int err;
-+
-+ if (pdev->dev.of_node)
-+ return snd_bcm2835_alsa_probe_dt(pdev);
-+
-+ if (dev >= MAX_SUBSTREAMS)
-+ return -ENODEV;
-+
-+ if (!enable[dev]) {
-+ dev++;
-+ return -ENOENT;
-+ }
-+
-+ if (dev > 0)
-+ goto add_register_map;
-+
-+ err = snd_card_new(NULL, index[dev], id[dev], THIS_MODULE, 0, &g_card);
-+ if (err < 0)
-+ goto out;
-+
-+ snd_card_set_dev(g_card, &pdev->dev);
-+ strcpy(g_card->driver, "bcm2835");
-+ strcpy(g_card->shortname, "bcm2835 ALSA");
-+ sprintf(g_card->longname, "%s", g_card->shortname);
-+
-+ err = snd_bcm2835_create(g_card, pdev, &chip);
-+ if (err < 0) {
-+ dev_err(&pdev->dev, "Failed to create bcm2835 chip\n");
-+ goto out_bcm2835_create;
-+ }
-+
-+ g_chip = chip;
-+ err = snd_bcm2835_new_pcm(chip);
-+ if (err < 0) {
-+ dev_err(&pdev->dev, "Failed to create new BCM2835 pcm device\n");
-+ goto out_bcm2835_new_pcm;
-+ }
-+
-+ err = snd_bcm2835_new_spdif_pcm(chip);
-+ if (err < 0) {
-+ dev_err(&pdev->dev, "Failed to create new BCM2835 spdif pcm device\n");
-+ goto out_bcm2835_new_spdif;
-+ }
-+
-+ err = snd_bcm2835_new_ctl(chip);
-+ if (err < 0) {
-+ dev_err(&pdev->dev, "Failed to create new BCM2835 ctl\n");
-+ goto out_bcm2835_new_ctl;
-+ }
-+
-+add_register_map:
-+ card = g_card;
-+ chip = g_chip;
-+
-+ BUG_ON(!(card && chip));
-+
-+ chip->avail_substreams |= (1 << dev);
-+ chip->pdev[dev] = pdev;
-+
-+ if (dev == 0) {
-+ err = snd_card_register(card);
-+ if (err < 0) {
-+ dev_err(&pdev->dev,
-+ "Failed to register bcm2835 ALSA card \n");
-+ goto out_card_register;
-+ }
-+ platform_set_drvdata(pdev, card);
-+ audio_info("bcm2835 ALSA card created!\n");
-+ } else {
-+ audio_info("bcm2835 ALSA chip created!\n");
-+ platform_set_drvdata(pdev, (void *)dev);
-+ }
-+
-+ dev++;
-+
-+ return 0;
-+
-+out_card_register:
-+out_bcm2835_new_ctl:
-+out_bcm2835_new_spdif:
-+out_bcm2835_new_pcm:
-+out_bcm2835_create:
-+ BUG_ON(!g_card);
-+ if (snd_card_free(g_card))
-+ dev_err(&pdev->dev, "Failed to free Registered alsa card\n");
-+ g_card = NULL;
-+out:
-+ dev = SNDRV_CARDS; /* stop more avail_substreams from being probed */
-+ dev_err(&pdev->dev, "BCM2835 ALSA Probe failed !!\n");
-+ return err;
-+}
-+
-+static int snd_bcm2835_alsa_remove(struct platform_device *pdev)
-+{
-+ uint32_t idx;
-+ void *drv_data;
-+
-+ drv_data = platform_get_drvdata(pdev);
-+
-+ if (drv_data == (void *)g_card) {
-+ /* This is the card device */
-+ snd_card_free((struct snd_card *)drv_data);
-+ g_card = NULL;
-+ g_chip = NULL;
-+ } else {
-+ idx = (uint32_t) drv_data;
-+ if (g_card != NULL) {
-+ BUG_ON(!g_chip);
-+ /* We pass chip device numbers in audio ipc devices
-+ * other than the one we registered our card with
-+ */
-+ idx = (uint32_t) drv_data;
-+ BUG_ON(!idx || idx > MAX_SUBSTREAMS);
-+ g_chip->avail_substreams &= ~(1 << idx);
-+ /* There should be atleast one substream registered
-+ * after we are done here, as it wil be removed when
-+ * the *remove* is called for the card device
-+ */
-+ BUG_ON(!g_chip->avail_substreams);
-+ }
-+ }
-+
-+ platform_set_drvdata(pdev, NULL);
-+
-+ return 0;
-+}
-+
-+#ifdef CONFIG_PM
-+static int snd_bcm2835_alsa_suspend(struct platform_device *pdev,
-+ pm_message_t state)
-+{
-+ return 0;
-+}
-+
-+static int snd_bcm2835_alsa_resume(struct platform_device *pdev)
-+{
-+ return 0;
-+}
-+
-+#endif
-+
-+static const struct of_device_id snd_bcm2835_of_match_table[] = {
-+ { .compatible = "brcm,bcm2835-audio", },
-+ {},
-+};
-+MODULE_DEVICE_TABLE(of, snd_bcm2835_of_match_table);
-+
-+static struct platform_driver bcm2835_alsa0_driver = {
-+ .probe = snd_bcm2835_alsa_probe,
-+ .remove = snd_bcm2835_alsa_remove,
-+#ifdef CONFIG_PM
-+ .suspend = snd_bcm2835_alsa_suspend,
-+ .resume = snd_bcm2835_alsa_resume,
-+#endif
-+ .driver = {
-+ .name = "bcm2835_AUD0",
-+ .owner = THIS_MODULE,
-+ .of_match_table = snd_bcm2835_of_match_table,
-+ },
-+};
-+
-+static struct platform_driver bcm2835_alsa1_driver = {
-+ .probe = snd_bcm2835_alsa_probe,
-+ .remove = snd_bcm2835_alsa_remove,
-+#ifdef CONFIG_PM
-+ .suspend = snd_bcm2835_alsa_suspend,
-+ .resume = snd_bcm2835_alsa_resume,
-+#endif
-+ .driver = {
-+ .name = "bcm2835_AUD1",
-+ .owner = THIS_MODULE,
-+ },
-+};
-+
-+static struct platform_driver bcm2835_alsa2_driver = {
-+ .probe = snd_bcm2835_alsa_probe,
-+ .remove = snd_bcm2835_alsa_remove,
-+#ifdef CONFIG_PM
-+ .suspend = snd_bcm2835_alsa_suspend,
-+ .resume = snd_bcm2835_alsa_resume,
-+#endif
-+ .driver = {
-+ .name = "bcm2835_AUD2",
-+ .owner = THIS_MODULE,
-+ },
-+};
-+
-+static struct platform_driver bcm2835_alsa3_driver = {
-+ .probe = snd_bcm2835_alsa_probe,
-+ .remove = snd_bcm2835_alsa_remove,
-+#ifdef CONFIG_PM
-+ .suspend = snd_bcm2835_alsa_suspend,
-+ .resume = snd_bcm2835_alsa_resume,
-+#endif
-+ .driver = {
-+ .name = "bcm2835_AUD3",
-+ .owner = THIS_MODULE,
-+ },
-+};
-+
-+static struct platform_driver bcm2835_alsa4_driver = {
-+ .probe = snd_bcm2835_alsa_probe,
-+ .remove = snd_bcm2835_alsa_remove,
-+#ifdef CONFIG_PM
-+ .suspend = snd_bcm2835_alsa_suspend,
-+ .resume = snd_bcm2835_alsa_resume,
-+#endif
-+ .driver = {
-+ .name = "bcm2835_AUD4",
-+ .owner = THIS_MODULE,
-+ },
-+};
-+
-+static struct platform_driver bcm2835_alsa5_driver = {
-+ .probe = snd_bcm2835_alsa_probe,
-+ .remove = snd_bcm2835_alsa_remove,
-+#ifdef CONFIG_PM
-+ .suspend = snd_bcm2835_alsa_suspend,
-+ .resume = snd_bcm2835_alsa_resume,
-+#endif
-+ .driver = {
-+ .name = "bcm2835_AUD5",
-+ .owner = THIS_MODULE,
-+ },
-+};
-+
-+static struct platform_driver bcm2835_alsa6_driver = {
-+ .probe = snd_bcm2835_alsa_probe,
-+ .remove = snd_bcm2835_alsa_remove,
-+#ifdef CONFIG_PM
-+ .suspend = snd_bcm2835_alsa_suspend,
-+ .resume = snd_bcm2835_alsa_resume,
-+#endif
-+ .driver = {
-+ .name = "bcm2835_AUD6",
-+ .owner = THIS_MODULE,
-+ },
-+};
-+
-+static struct platform_driver bcm2835_alsa7_driver = {
-+ .probe = snd_bcm2835_alsa_probe,
-+ .remove = snd_bcm2835_alsa_remove,
-+#ifdef CONFIG_PM
-+ .suspend = snd_bcm2835_alsa_suspend,
-+ .resume = snd_bcm2835_alsa_resume,
-+#endif
-+ .driver = {
-+ .name = "bcm2835_AUD7",
-+ .owner = THIS_MODULE,
-+ },
-+};
-+
-+static int bcm2835_alsa_device_init(void)
-+{
-+ int err;
-+ err = platform_driver_register(&bcm2835_alsa0_driver);
-+ if (err) {
-+ pr_err("Error registering bcm2835_alsa0_driver %d .\n", err);
-+ goto out;
-+ }
-+
-+ err = platform_driver_register(&bcm2835_alsa1_driver);
-+ if (err) {
-+ pr_err("Error registering bcm2835_alsa0_driver %d .\n", err);
-+ goto unregister_0;
-+ }
-+
-+ err = platform_driver_register(&bcm2835_alsa2_driver);
-+ if (err) {
-+ pr_err("Error registering bcm2835_alsa0_driver %d .\n", err);
-+ goto unregister_1;
-+ }
-+
-+ err = platform_driver_register(&bcm2835_alsa3_driver);
-+ if (err) {
-+ pr_err("Error registering bcm2835_alsa0_driver %d .\n", err);
-+ goto unregister_2;
-+ }
-+
-+ err = platform_driver_register(&bcm2835_alsa4_driver);
-+ if (err) {
-+ pr_err("Error registering bcm2835_alsa0_driver %d .\n", err);
-+ goto unregister_3;
-+ }
-+
-+ err = platform_driver_register(&bcm2835_alsa5_driver);
-+ if (err) {
-+ pr_err("Error registering bcm2835_alsa0_driver %d .\n", err);
-+ goto unregister_4;
-+ }
-+
-+ err = platform_driver_register(&bcm2835_alsa6_driver);
-+ if (err) {
-+ pr_err("Error registering bcm2835_alsa0_driver %d .\n", err);
-+ goto unregister_5;
-+ }
-+
-+ err = platform_driver_register(&bcm2835_alsa7_driver);
-+ if (err) {
-+ pr_err("Error registering bcm2835_alsa0_driver %d .\n", err);
-+ goto unregister_6;
-+ }
-+
-+ return 0;
-+
-+unregister_6:
-+ platform_driver_unregister(&bcm2835_alsa6_driver);
-+unregister_5:
-+ platform_driver_unregister(&bcm2835_alsa5_driver);
-+unregister_4:
-+ platform_driver_unregister(&bcm2835_alsa4_driver);
-+unregister_3:
-+ platform_driver_unregister(&bcm2835_alsa3_driver);
-+unregister_2:
-+ platform_driver_unregister(&bcm2835_alsa2_driver);
-+unregister_1:
-+ platform_driver_unregister(&bcm2835_alsa1_driver);
-+unregister_0:
-+ platform_driver_unregister(&bcm2835_alsa0_driver);
-+out:
-+ return err;
-+}
-+
-+static void bcm2835_alsa_device_exit(void)
-+{
-+ platform_driver_unregister(&bcm2835_alsa0_driver);
-+ platform_driver_unregister(&bcm2835_alsa1_driver);
-+ platform_driver_unregister(&bcm2835_alsa2_driver);
-+ platform_driver_unregister(&bcm2835_alsa3_driver);
-+ platform_driver_unregister(&bcm2835_alsa4_driver);
-+ platform_driver_unregister(&bcm2835_alsa5_driver);
-+ platform_driver_unregister(&bcm2835_alsa6_driver);
-+ platform_driver_unregister(&bcm2835_alsa7_driver);
-+}
-+
-+late_initcall(bcm2835_alsa_device_init);
-+module_exit(bcm2835_alsa_device_exit);
-+
-+MODULE_AUTHOR("Dom Cobley");
-+MODULE_DESCRIPTION("Alsa driver for BCM2835 chip");
-+MODULE_LICENSE("GPL");
-+MODULE_ALIAS("platform:bcm2835_alsa");
---- /dev/null
-+++ b/sound/arm/bcm2835.h
-@@ -0,0 +1,167 @@
-+/*****************************************************************************
-+* Copyright 2011 Broadcom Corporation. All rights reserved.
-+*
-+* Unless you and Broadcom execute a separate written software license
-+* agreement governing use of this software, this software is licensed to you
-+* under the terms of the GNU General Public License version 2, available at
-+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
-+*
-+* Notwithstanding the above, under no circumstances may you combine this
-+* software in any way with any other Broadcom software provided under a
-+* license other than the GPL, without Broadcom's express prior written
-+* consent.
-+*****************************************************************************/
-+
-+#ifndef __SOUND_ARM_BCM2835_H
-+#define __SOUND_ARM_BCM2835_H
-+
-+#include <linux/device.h>
-+#include <linux/list.h>
-+#include <linux/interrupt.h>
-+#include <linux/wait.h>
-+#include <sound/core.h>
-+#include <sound/initval.h>
-+#include <sound/pcm.h>
-+#include <sound/pcm_params.h>
-+#include <sound/pcm-indirect.h>
-+#include <linux/workqueue.h>
-+
-+/*
-+#define AUDIO_DEBUG_ENABLE
-+#define AUDIO_VERBOSE_DEBUG_ENABLE
-+*/
-+
-+/* Debug macros */
-+
-+#ifdef AUDIO_DEBUG_ENABLE
-+#ifdef AUDIO_VERBOSE_DEBUG_ENABLE
-+
-+#define audio_debug(fmt, arg...) \
-+ printk(KERN_INFO"%s:%d " fmt, __func__, __LINE__, ##arg)
-+
-+#define audio_info(fmt, arg...) \
-+ printk(KERN_INFO"%s:%d " fmt, __func__, __LINE__, ##arg)
-+
-+#else
-+
-+#define audio_debug(fmt, arg...)
-+
-+#define audio_info(fmt, arg...)
-+
-+#endif /* AUDIO_VERBOSE_DEBUG_ENABLE */
-+
-+#else
-+
-+#define audio_debug(fmt, arg...)
-+
-+#define audio_info(fmt, arg...)
-+
-+#endif /* AUDIO_DEBUG_ENABLE */
-+
-+#define audio_error(fmt, arg...) \
-+ printk(KERN_ERR"%s:%d " fmt, __func__, __LINE__, ##arg)
-+
-+#define audio_warning(fmt, arg...) \
-+ printk(KERN_WARNING"%s:%d " fmt, __func__, __LINE__, ##arg)
-+
-+#define audio_alert(fmt, arg...) \
-+ printk(KERN_ALERT"%s:%d " fmt, __func__, __LINE__, ##arg)
-+
-+#define MAX_SUBSTREAMS (8)
-+#define AVAIL_SUBSTREAMS_MASK (0xff)
-+enum {
-+ CTRL_VOL_MUTE,
-+ CTRL_VOL_UNMUTE
-+};
-+
-+/* macros for alsa2chip and chip2alsa, instead of functions */
-+
-+#define alsa2chip(vol) (uint)(-((vol << 8) / 100)) /* convert alsa to chip volume (defined as macro rather than function call) */
-+#define chip2alsa(vol) -((vol * 100) >> 8) /* convert chip to alsa volume */
-+
-+/* Some constants for values .. */
-+typedef enum {
-+ AUDIO_DEST_AUTO = 0,
-+ AUDIO_DEST_HEADPHONES = 1,
-+ AUDIO_DEST_HDMI = 2,
-+ AUDIO_DEST_MAX,
-+} SND_BCM2835_ROUTE_T;
-+
-+typedef enum {
-+ PCM_PLAYBACK_VOLUME,
-+ PCM_PLAYBACK_MUTE,
-+ PCM_PLAYBACK_DEVICE,
-+} SND_BCM2835_CTRL_T;
-+
-+/* definition of the chip-specific record */
-+typedef struct bcm2835_chip {
-+ struct snd_card *card;
-+ struct snd_pcm *pcm;
-+ struct snd_pcm *pcm_spdif;
-+ /* Bitmat for valid reg_base and irq numbers */
-+ uint32_t avail_substreams;
-+ struct platform_device *pdev[MAX_SUBSTREAMS];
-+ struct bcm2835_alsa_stream *alsa_stream[MAX_SUBSTREAMS];
-+
-+ int volume;
-+ int old_volume; /* stores the volume value whist muted */
-+ int dest;
-+ int mute;
-+
-+ unsigned int opened;
-+ unsigned int spdif_status;
-+ struct mutex audio_mutex;
-+} bcm2835_chip_t;
-+
-+typedef struct bcm2835_alsa_stream {
-+ bcm2835_chip_t *chip;
-+ struct snd_pcm_substream *substream;
-+ struct snd_pcm_indirect pcm_indirect;
-+
-+ struct semaphore buffers_update_sem;
-+ struct semaphore control_sem;
-+ spinlock_t lock;
-+ volatile uint32_t control;
-+ volatile uint32_t status;
-+
-+ int open;
-+ int running;
-+ int draining;
-+
-+ int channels;
-+ int params_rate;
-+ int pcm_format_width;
-+
-+ unsigned int pos;
-+ unsigned int buffer_size;
-+ unsigned int period_size;
-+
-+ uint32_t enable_fifo_irq;
-+ irq_handler_t fifo_irq_handler;
-+
-+ atomic_t retrieved;
-+ struct opaque_AUDIO_INSTANCE_T *instance;
-+ struct workqueue_struct *my_wq;
-+ int idx;
-+} bcm2835_alsa_stream_t;
-+
-+int snd_bcm2835_new_ctl(bcm2835_chip_t * chip);
-+int snd_bcm2835_new_pcm(bcm2835_chip_t * chip);
-+int snd_bcm2835_new_spdif_pcm(bcm2835_chip_t * chip);
-+
-+int bcm2835_audio_open(bcm2835_alsa_stream_t * alsa_stream);
-+int bcm2835_audio_close(bcm2835_alsa_stream_t * alsa_stream);
-+int bcm2835_audio_set_params(bcm2835_alsa_stream_t * alsa_stream,
-+ uint32_t channels, uint32_t samplerate,
-+ uint32_t bps);
-+int bcm2835_audio_setup(bcm2835_alsa_stream_t * alsa_stream);
-+int bcm2835_audio_start(bcm2835_alsa_stream_t * alsa_stream);
-+int bcm2835_audio_stop(bcm2835_alsa_stream_t * alsa_stream);
-+int bcm2835_audio_set_ctls(bcm2835_chip_t * chip);
-+int bcm2835_audio_write(bcm2835_alsa_stream_t * alsa_stream, uint32_t count,
-+ void *src);
-+uint32_t bcm2835_audio_retrieve_buffers(bcm2835_alsa_stream_t * alsa_stream);
-+void bcm2835_audio_flush_buffers(bcm2835_alsa_stream_t * alsa_stream);
-+void bcm2835_audio_flush_playback_buffers(bcm2835_alsa_stream_t * alsa_stream);
-+
-+#endif /* __SOUND_ARM_BCM2835_H */
---- /dev/null
-+++ b/sound/arm/vc_vchi_audioserv_defs.h
-@@ -0,0 +1,116 @@
-+/*****************************************************************************
-+* Copyright 2011 Broadcom Corporation. All rights reserved.
-+*
-+* Unless you and Broadcom execute a separate written software license
-+* agreement governing use of this software, this software is licensed to you
-+* under the terms of the GNU General Public License version 2, available at
-+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
-+*
-+* Notwithstanding the above, under no circumstances may you combine this
-+* software in any way with any other Broadcom software provided under a
-+* license other than the GPL, without Broadcom's express prior written
-+* consent.
-+*****************************************************************************/
-+
-+#ifndef _VC_AUDIO_DEFS_H_
-+#define _VC_AUDIO_DEFS_H_
-+
-+#define VC_AUDIOSERV_MIN_VER 1
-+#define VC_AUDIOSERV_VER 2
-+
-+// FourCC code used for VCHI connection
-+#define VC_AUDIO_SERVER_NAME MAKE_FOURCC("AUDS")
-+
-+// Maximum message length
-+#define VC_AUDIO_MAX_MSG_LEN (sizeof( VC_AUDIO_MSG_T ))
-+
-+// List of screens that are currently supported
-+// All message types supported for HOST->VC direction
-+typedef enum {
-+ VC_AUDIO_MSG_TYPE_RESULT, // Generic result
-+ VC_AUDIO_MSG_TYPE_COMPLETE, // Generic result
-+ VC_AUDIO_MSG_TYPE_CONFIG, // Configure audio
-+ VC_AUDIO_MSG_TYPE_CONTROL, // Configure audio
-+ VC_AUDIO_MSG_TYPE_OPEN, // Configure audio
-+ VC_AUDIO_MSG_TYPE_CLOSE, // Configure audio
-+ VC_AUDIO_MSG_TYPE_START, // Configure audio
-+ VC_AUDIO_MSG_TYPE_STOP, // Configure audio
-+ VC_AUDIO_MSG_TYPE_WRITE, // Configure audio
-+ VC_AUDIO_MSG_TYPE_MAX
-+} VC_AUDIO_MSG_TYPE;
-+
-+// configure the audio
-+typedef struct {
-+ uint32_t channels;
-+ uint32_t samplerate;
-+ uint32_t bps;
-+
-+} VC_AUDIO_CONFIG_T;
-+
-+typedef struct {
-+ uint32_t volume;
-+ uint32_t dest;
-+
-+} VC_AUDIO_CONTROL_T;
-+
-+// audio
-+typedef struct {
-+ uint32_t dummy;
-+
-+} VC_AUDIO_OPEN_T;
-+
-+// audio
-+typedef struct {
-+ uint32_t dummy;
-+
-+} VC_AUDIO_CLOSE_T;
-+// audio
-+typedef struct {
-+ uint32_t dummy;
-+
-+} VC_AUDIO_START_T;
-+// audio
-+typedef struct {
-+ uint32_t draining;
-+
-+} VC_AUDIO_STOP_T;
-+
-+// configure the write audio samples
-+typedef struct {
-+ uint32_t count; // in bytes
-+ void *callback;
-+ void *cookie;
-+ uint16_t silence;
-+ uint16_t max_packet;
-+} VC_AUDIO_WRITE_T;
-+
-+// Generic result for a request (VC->HOST)
-+typedef struct {
-+ int32_t success; // Success value
-+
-+} VC_AUDIO_RESULT_T;
-+
-+// Generic result for a request (VC->HOST)
-+typedef struct {
-+ int32_t count; // Success value
-+ void *callback;
-+ void *cookie;
-+} VC_AUDIO_COMPLETE_T;
-+
-+// Message header for all messages in HOST->VC direction
-+typedef struct {
-+ int32_t type; // Message type (VC_AUDIO_MSG_TYPE)
-+ union {
-+ VC_AUDIO_CONFIG_T config;
-+ VC_AUDIO_CONTROL_T control;
-+ VC_AUDIO_OPEN_T open;
-+ VC_AUDIO_CLOSE_T close;
-+ VC_AUDIO_START_T start;
-+ VC_AUDIO_STOP_T stop;
-+ VC_AUDIO_WRITE_T write;
-+ VC_AUDIO_RESULT_T result;
-+ VC_AUDIO_COMPLETE_T complete;
-+ } u;
-+} VC_AUDIO_MSG_T;
-+
-+#endif // _VC_AUDIO_DEFS_H_
diff --git a/target/linux/brcm2708/patches-4.4/0036-bcm2708-vchiq-driver.patch b/target/linux/brcm2708/patches-4.4/0036-bcm2708-vchiq-driver.patch
deleted file mode 100644
index 054e7c7..0000000
--- a/target/linux/brcm2708/patches-4.4/0036-bcm2708-vchiq-driver.patch
+++ /dev/null
@@ -1,13200 +0,0 @@
-From 53aab3c7125044c44cffde9a3228ccead21d799c Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Tue, 2 Jul 2013 23:42:01 +0100
-Subject: [PATCH] bcm2708 vchiq driver
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Signed-off-by: popcornmix <popcornmix at gmail.com>
-
-vchiq: create_pagelist copes with vmalloc memory
-
-Signed-off-by: Daniel Stone <daniels at collabora.com>
-
-vchiq: fix the shim message release
-
-Signed-off-by: Daniel Stone <daniels at collabora.com>
-
-vchiq: export additional symbols
-
-Signed-off-by: Daniel Stone <daniels at collabora.com>
-
-VCHIQ: Make service closure fully synchronous (drv)
-
-This is one half of a two-part patch, the other half of which is to
-the vchiq_lib user library. With these patches, calls to
-vchiq_close_service and vchiq_remove_service won't return until any
-associated callbacks have been delivered to the callback thread.
-
-VCHIQ: Add per-service tracing
-
-The new service option VCHIQ_SERVICE_OPTION_TRACE is a boolean that
-toggles tracing for the specified service.
-
-This commit also introduces vchi_service_set_option and the associated
-option VCHI_SERVICE_OPTION_TRACE.
-
-vchiq: Make the synchronous-CLOSE logic more tolerant
-
-vchiq: Move logging control into debugfs
-
-vchiq: Take care of a corner case tickled by VCSM
-
-Closing a connection that isn't fully open requires care, since one
-side does not know the other side's port number. Code was present to
-handle the case where a CLOSE is sent immediately after an OPEN, i.e.
-before the OPENACK has been received, but this was incorrectly being
-used when an OPEN from a client using port 0 was rejected.
-
-(In the observed failure, the host was attempting to use the VCSM
-service, which isn't present in the 'cutdown' firmware. The failure
-was intermittent because sometimes the keepalive service would
-grab port 0.)
-
-This case can be distinguished because the client's remoteport will
-still be VCHIQ_PORT_FREE, and the srvstate will be OPENING. Either
-condition is sufficient to differentiate it from the special case
-described above.
-
-vchiq: Avoid high load when blocked and unkillable
-
-vchiq: Include SIGSTOP and SIGCONT in list of signals not-masked by vchiq to allow gdb to work
-
-vchiq_arm: Complete support for SYNCHRONOUS mode
-
-vchiq: Remove inline from suspend/resume
-
-vchiq: Allocation does not need to be atomic
-
-vchiq: Fix wrong condition check
-
-The log level is checked from within the log call. Remove the check in the call.
-
-Signed-off-by: Pranith Kumar <bobby.prani at gmail.com>
-
-BCM270x: Add vchiq device to platform file and Device Tree
-
-Prepare to turn the vchiq module into a driver.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-bcm2708: vchiq: Add Device Tree support
-
-Turn vchiq into a driver and stop hardcoding resources.
-Use devm_* functions in probe path to simplify cleanup.
-A global variable is used to hold the register address. This is done
-to keep this patch as small as possible.
-Also make available on ARCH_BCM2835.
-Based on work by Lubomir Rintel.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-vchiq: Change logging level for inbound data
-
-vchiq_arm: Two cacheing fixes
-
-1) Make fragment size vary with cache line size
-Without this patch, non-cache-line-aligned transfers may corrupt
-(or be corrupted by) adjacent data structures.
-
-Both ARM and VC need to be updated to enable this feature. This is
-ensured by having the loader apply a new DT parameter -
-cache-line-size. The existence of this parameter guarantees that the
-kernel is capable, and the parameter will only be modified from the
-safe default if the loader is capable.
-
-2) Flush/invalidate vmalloc'd memory, and invalidate after reads
-
-vchiq: fix NULL pointer dereference when closing driver
-
-The following code run as root will cause a null pointer dereference oops:
-
- int fd = open("/dev/vc-cma", O_RDONLY);
- if (fd < 0)
- err(1, "open failed");
- (void)close(fd);
-
-[ 1704.877721] Unable to handle kernel NULL pointer dereference at virtual address 00000000
-[ 1704.877725] pgd = b899c000
-[ 1704.877736] [00000000] *pgd=37fab831, *pte=00000000, *ppte=00000000
-[ 1704.877748] Internal error: Oops: 817 [#1] PREEMPT SMP ARM
-[ 1704.877765] Modules linked in: evdev i2c_bcm2708 uio_pdrv_genirq uio
-[ 1704.877774] CPU: 2 PID: 3656 Comm: stress-ng-fstat Not tainted 3.19.1-12-generic-bcm2709 #12-Ubuntu
-[ 1704.877777] Hardware name: BCM2709
-[ 1704.877783] task: b8ab9b00 ti: b7e68000 task.ti: b7e68000
-[ 1704.877798] PC is at __down_interruptible+0x50/0xec
-[ 1704.877806] LR is at down_interruptible+0x5c/0x68
-[ 1704.877813] pc : [<80630ee8>] lr : [<800704b0>] psr: 60080093
-sp : b7e69e50 ip : b7e69e88 fp : b7e69e84
-[ 1704.877817] r10: b88123c8 r9 : 00000010 r8 : 00000001
-[ 1704.877822] r7 : b8ab9b00 r6 : 7fffffff r5 : 80a1cc34 r4 : 80a1cc34
-[ 1704.877826] r3 : b7e69e50 r2 : 00000000 r1 : 00000000 r0 : 80a1cc34
-[ 1704.877833] Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
-[ 1704.877838] Control: 10c5387d Table: 3899c06a DAC: 00000015
-[ 1704.877843] Process do-oops (pid: 3656, stack limit = 0xb7e68238)
-[ 1704.877848] Stack: (0xb7e69e50 to 0xb7e6a000)
-[ 1704.877856] 9e40: 80a1cc3c 00000000 00000010 b88123c8
-[ 1704.877865] 9e60: b7e69e84 80a1cc34 fff9fee9 ffffffff b7e68000 00000009 b7e69ea4 b7e69e88
-[ 1704.877874] 9e80: 800704b0 80630ea4 fff9fee9 60080013 80a1cc28 fff9fee9 b7e69edc b7e69ea8
-[ 1704.877884] 9ea0: 8040f558 80070460 fff9fee9 ffffffff 00000000 00000000 00000009 80a1cb7c
-[ 1704.877893] 9ec0: 00000000 80a1cb7c 00000000 00000010 b7e69ef4 b7e69ee0 803e1ba4 8040f514
-[ 1704.877902] 9ee0: 00000e48 80a1cb7c b7e69f14 b7e69ef8 803e1c9c 803e1b74 b88123c0 b92acb18
-[ 1704.877911] 9f00: b8812790 b8d815d8 b7e69f24 b7e69f18 803e2250 803e1bc8 b7e69f5c b7e69f28
-[ 1704.877921] 9f20: 80167bac 803e222c 00000000 00000000 b7e69f54 b8ab9ffc 00000000 8098c794
-[ 1704.877930] 9f40: b8ab9b00 8000efc4 b7e68000 00000000 b7e69f6c b7e69f60 80167d6c 80167b28
-[ 1704.877939] 9f60: b7e69f8c b7e69f70 80047d38 80167d60 b7e68000 b7e68010 8000efc4 b7e69fb0
-[ 1704.877949] 9f80: b7e69fac b7e69f90 80012820 80047c84 01155490 011549a8 00000001 00000006
-[ 1704.877957] 9fa0: 00000000 b7e69fb0 8000ee5c 80012790 00000000 353d8c0f 7efc4308 00000000
-[ 1704.877966] 9fc0: 01155490 011549a8 00000001 00000006 00000000 00000000 76cf3ba0 00000003
-[ 1704.877975] 9fe0: 00000000 7efc42e4 0002272f 76e2ed66 60080030 00000003 00000000 00000000
-[ 1704.877998] [<80630ee8>] (__down_interruptible) from [<800704b0>] (down_interruptible+0x5c/0x68)
-[ 1704.878015] [<800704b0>] (down_interruptible) from [<8040f558>] (vchiu_queue_push+0x50/0xd8)
-[ 1704.878032] [<8040f558>] (vchiu_queue_push) from [<803e1ba4>] (send_worker_msg+0x3c/0x54)
-[ 1704.878045] [<803e1ba4>] (send_worker_msg) from [<803e1c9c>] (vc_cma_set_reserve+0xe0/0x1c4)
-[ 1704.878057] [<803e1c9c>] (vc_cma_set_reserve) from [<803e2250>] (vc_cma_release+0x30/0x38)
-[ 1704.878069] [<803e2250>] (vc_cma_release) from [<80167bac>] (__fput+0x90/0x1e0)
-[ 1704.878082] [<80167bac>] (__fput) from [<80167d6c>] (____fput+0x18/0x1c)
-[ 1704.878094] [<80167d6c>] (____fput) from [<80047d38>] (task_work_run+0xc0/0xf8)
-[ 1704.878109] [<80047d38>] (task_work_run) from [<80012820>] (do_work_pending+0x9c/0xc4)
-[ 1704.878123] [<80012820>] (do_work_pending) from [<8000ee5c>] (work_pending+0xc/0x20)
-[ 1704.878133] Code: e50b1034 e3a01000 e50b2030 e580300c (e5823000)
-
-..the fix is to ensure that we have actually initialized the queue before we attempt
-to push any items onto it. This occurs if we do an open() followed by a close() without
-any activity in between.
-
-Signed-off-by: Colin Ian King <colin.king at canonical.com>
-
-vchiq_arm: Sort out the vmalloc case
-
-See: https://github.com/raspberrypi/linux/issues/1055
-
-vchiq: hack: Add include depecated dma include file
----
- arch/arm/mach-bcm2708/include/mach/platform.h | 2 +
- arch/arm/mach-bcm2709/include/mach/platform.h | 2 +
- drivers/misc/Kconfig | 1 +
- drivers/misc/Makefile | 1 +
- drivers/misc/vc04_services/Kconfig | 9 +
- drivers/misc/vc04_services/Makefile | 14 +
- .../interface/vchi/connections/connection.h | 328 ++
- .../interface/vchi/message_drivers/message.h | 204 +
- drivers/misc/vc04_services/interface/vchi/vchi.h | 378 ++
- .../misc/vc04_services/interface/vchi/vchi_cfg.h | 224 ++
- .../interface/vchi/vchi_cfg_internal.h | 71 +
- .../vc04_services/interface/vchi/vchi_common.h | 175 +
- .../misc/vc04_services/interface/vchi/vchi_mh.h | 42 +
- .../misc/vc04_services/interface/vchiq_arm/vchiq.h | 40 +
- .../vc04_services/interface/vchiq_arm/vchiq_2835.h | 42 +
- .../interface/vchiq_arm/vchiq_2835_arm.c | 586 +++
- .../vc04_services/interface/vchiq_arm/vchiq_arm.c | 2903 +++++++++++++++
- .../vc04_services/interface/vchiq_arm/vchiq_arm.h | 220 ++
- .../interface/vchiq_arm/vchiq_build_info.h | 37 +
- .../vc04_services/interface/vchiq_arm/vchiq_cfg.h | 69 +
- .../interface/vchiq_arm/vchiq_connected.c | 120 +
- .../interface/vchiq_arm/vchiq_connected.h | 50 +
- .../vc04_services/interface/vchiq_arm/vchiq_core.c | 3934 ++++++++++++++++++++
- .../vc04_services/interface/vchiq_arm/vchiq_core.h | 712 ++++
- .../interface/vchiq_arm/vchiq_debugfs.c | 383 ++
- .../interface/vchiq_arm/vchiq_debugfs.h | 52 +
- .../interface/vchiq_arm/vchiq_genversion | 87 +
- .../vc04_services/interface/vchiq_arm/vchiq_if.h | 189 +
- .../interface/vchiq_arm/vchiq_ioctl.h | 131 +
- .../interface/vchiq_arm/vchiq_kern_lib.c | 458 +++
- .../interface/vchiq_arm/vchiq_killable.h | 69 +
- .../interface/vchiq_arm/vchiq_memdrv.h | 71 +
- .../interface/vchiq_arm/vchiq_pagelist.h | 58 +
- .../vc04_services/interface/vchiq_arm/vchiq_shim.c | 860 +++++
- .../vc04_services/interface/vchiq_arm/vchiq_util.c | 156 +
- .../vc04_services/interface/vchiq_arm/vchiq_util.h | 82 +
- .../interface/vchiq_arm/vchiq_version.c | 59 +
- 37 files changed, 12819 insertions(+)
- create mode 100644 drivers/misc/vc04_services/Kconfig
- create mode 100644 drivers/misc/vc04_services/Makefile
- create mode 100644 drivers/misc/vc04_services/interface/vchi/connections/connection.h
- create mode 100644 drivers/misc/vc04_services/interface/vchi/message_drivers/message.h
- create mode 100644 drivers/misc/vc04_services/interface/vchi/vchi.h
- create mode 100644 drivers/misc/vc04_services/interface/vchi/vchi_cfg.h
- create mode 100644 drivers/misc/vc04_services/interface/vchi/vchi_cfg_internal.h
- create mode 100644 drivers/misc/vc04_services/interface/vchi/vchi_common.h
- create mode 100644 drivers/misc/vc04_services/interface/vchi/vchi_mh.h
- create mode 100644 drivers/misc/vc04_services/interface/vchiq_arm/vchiq.h
- create mode 100644 drivers/misc/vc04_services/interface/vchiq_arm/vchiq_2835.h
- create mode 100644 drivers/misc/vc04_services/interface/vchiq_arm/vchiq_2835_arm.c
- create mode 100644 drivers/misc/vc04_services/interface/vchiq_arm/vchiq_arm.c
- create mode 100644 drivers/misc/vc04_services/interface/vchiq_arm/vchiq_arm.h
- create mode 100644 drivers/misc/vc04_services/interface/vchiq_arm/vchiq_build_info.h
- create mode 100644 drivers/misc/vc04_services/interface/vchiq_arm/vchiq_cfg.h
- create mode 100644 drivers/misc/vc04_services/interface/vchiq_arm/vchiq_connected.c
- create mode 100644 drivers/misc/vc04_services/interface/vchiq_arm/vchiq_connected.h
- create mode 100644 drivers/misc/vc04_services/interface/vchiq_arm/vchiq_core.c
- create mode 100644 drivers/misc/vc04_services/interface/vchiq_arm/vchiq_core.h
- create mode 100644 drivers/misc/vc04_services/interface/vchiq_arm/vchiq_debugfs.c
- create mode 100644 drivers/misc/vc04_services/interface/vchiq_arm/vchiq_debugfs.h
- create mode 100644 drivers/misc/vc04_services/interface/vchiq_arm/vchiq_genversion
- create mode 100644 drivers/misc/vc04_services/interface/vchiq_arm/vchiq_if.h
- create mode 100644 drivers/misc/vc04_services/interface/vchiq_arm/vchiq_ioctl.h
- create mode 100644 drivers/misc/vc04_services/interface/vchiq_arm/vchiq_kern_lib.c
- create mode 100644 drivers/misc/vc04_services/interface/vchiq_arm/vchiq_killable.h
- create mode 100644 drivers/misc/vc04_services/interface/vchiq_arm/vchiq_memdrv.h
- create mode 100644 drivers/misc/vc04_services/interface/vchiq_arm/vchiq_pagelist.h
- create mode 100644 drivers/misc/vc04_services/interface/vchiq_arm/vchiq_shim.c
- create mode 100644 drivers/misc/vc04_services/interface/vchiq_arm/vchiq_util.c
- create mode 100644 drivers/misc/vc04_services/interface/vchiq_arm/vchiq_util.h
- create mode 100644 drivers/misc/vc04_services/interface/vchiq_arm/vchiq_version.c
-
---- a/arch/arm/mach-bcm2708/include/mach/platform.h
-+++ b/arch/arm/mach-bcm2708/include/mach/platform.h
-@@ -78,6 +78,8 @@
- #define ARMCTRL_IC_BASE (ARM_BASE + 0x200) /* ARM interrupt controller */
- #define ARMCTRL_TIMER0_1_BASE (ARM_BASE + 0x400) /* Timer 0 and 1 */
- #define ARMCTRL_0_SBM_BASE (ARM_BASE + 0x800) /* User 0 (ARM)'s Semaphores Doorbells and Mailboxes */
-+#define ARMCTRL_0_BELL_BASE (ARMCTRL_0_SBM_BASE + 0x40) /* User 0 (ARM)'s Doorbell */
-+#define ARMCTRL_0_MAIL0_BASE (ARMCTRL_0_SBM_BASE + 0x80) /* User 0 (ARM)'s Mailbox 0 */
-
- /*
- * Watchdog
---- a/arch/arm/mach-bcm2709/include/mach/platform.h
-+++ b/arch/arm/mach-bcm2709/include/mach/platform.h
-@@ -78,6 +78,8 @@
- #define ARMCTRL_IC_BASE (ARM_BASE + 0x200) /* ARM interrupt controller */
- #define ARMCTRL_TIMER0_1_BASE (ARM_BASE + 0x400) /* Timer 0 and 1 */
- #define ARMCTRL_0_SBM_BASE (ARM_BASE + 0x800) /* User 0 (ARM)'s Semaphores Doorbells and Mailboxes */
-+#define ARMCTRL_0_BELL_BASE (ARMCTRL_0_SBM_BASE + 0x40) /* User 0 (ARM)'s Doorbell */
-+#define ARMCTRL_0_MAIL0_BASE (ARMCTRL_0_SBM_BASE + 0x80) /* User 0 (ARM)'s Mailbox 0 */
-
- /*
- * Watchdog
---- a/drivers/misc/Kconfig
-+++ b/drivers/misc/Kconfig
-@@ -545,6 +545,7 @@ source "drivers/misc/lis3lv02d/Kconfig"
- source "drivers/misc/altera-stapl/Kconfig"
- source "drivers/misc/mei/Kconfig"
- source "drivers/misc/vmw_vmci/Kconfig"
-+source "drivers/misc/vc04_services/Kconfig"
- source "drivers/misc/mic/Kconfig"
- source "drivers/misc/genwqe/Kconfig"
- source "drivers/misc/echo/Kconfig"
---- a/drivers/misc/Makefile
-+++ b/drivers/misc/Makefile
-@@ -52,6 +52,7 @@ obj-$(CONFIG_INTEL_MEI) += mei/
- obj-$(CONFIG_VMWARE_VMCI) += vmw_vmci/
- obj-$(CONFIG_LATTICE_ECP3_CONFIG) += lattice-ecp3-config.o
- obj-$(CONFIG_SRAM) += sram.o
-+obj-$(CONFIG_BCM2708_VCHIQ) += vc04_services/
- obj-y += mic/
- obj-$(CONFIG_GENWQE) += genwqe/
- obj-$(CONFIG_ECHO) += echo/
---- /dev/null
-+++ b/drivers/misc/vc04_services/Kconfig
-@@ -0,0 +1,9 @@
-+config BCM2708_VCHIQ
-+ tristate "Videocore VCHIQ"
-+ depends on RASPBERRYPI_FIRMWARE
-+ default y
-+ help
-+ Kernel to VideoCore communication interface for the
-+ BCM2708 family of products.
-+ Defaults to Y when the Broadcom Videocore services
-+ are included in the build, N otherwise.
---- /dev/null
-+++ b/drivers/misc/vc04_services/Makefile
-@@ -0,0 +1,14 @@
-+obj-$(CONFIG_BCM2708_VCHIQ) += vchiq.o
-+
-+vchiq-objs := \
-+ interface/vchiq_arm/vchiq_core.o \
-+ interface/vchiq_arm/vchiq_arm.o \
-+ interface/vchiq_arm/vchiq_kern_lib.o \
-+ interface/vchiq_arm/vchiq_2835_arm.o \
-+ interface/vchiq_arm/vchiq_debugfs.o \
-+ interface/vchiq_arm/vchiq_shim.o \
-+ interface/vchiq_arm/vchiq_util.o \
-+ interface/vchiq_arm/vchiq_connected.o \
-+
-+ccflags-y += -DVCOS_VERIFY_BKPTS=1 -Idrivers/misc/vc04_services -DUSE_VCHIQ_ARM -D__VCCOREVER__=0x04000000
-+
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchi/connections/connection.h
-@@ -0,0 +1,328 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#ifndef CONNECTION_H_
-+#define CONNECTION_H_
-+
-+#include <linux/kernel.h>
-+#include <linux/types.h>
-+#include <linux/semaphore.h>
-+
-+#include "interface/vchi/vchi_cfg_internal.h"
-+#include "interface/vchi/vchi_common.h"
-+#include "interface/vchi/message_drivers/message.h"
-+
-+/******************************************************************************
-+ Global defs
-+ *****************************************************************************/
-+
-+// Opaque handle for a connection / service pair
-+typedef struct opaque_vchi_connection_connected_service_handle_t *VCHI_CONNECTION_SERVICE_HANDLE_T;
-+
-+// opaque handle to the connection state information
-+typedef struct opaque_vchi_connection_info_t VCHI_CONNECTION_STATE_T;
-+
-+typedef struct vchi_connection_t VCHI_CONNECTION_T;
-+
-+
-+/******************************************************************************
-+ API
-+ *****************************************************************************/
-+
-+// Routine to init a connection with a particular low level driver
-+typedef VCHI_CONNECTION_STATE_T * (*VCHI_CONNECTION_INIT_T)( struct vchi_connection_t * connection,
-+ const VCHI_MESSAGE_DRIVER_T * driver );
-+
-+// Routine to control CRC enabling at a connection level
-+typedef int32_t (*VCHI_CONNECTION_CRC_CONTROL_T)( VCHI_CONNECTION_STATE_T *state_handle,
-+ VCHI_CRC_CONTROL_T control );
-+
-+// Routine to create a service
-+typedef int32_t (*VCHI_CONNECTION_SERVICE_CONNECT_T)( VCHI_CONNECTION_STATE_T *state_handle,
-+ int32_t service_id,
-+ uint32_t rx_fifo_size,
-+ uint32_t tx_fifo_size,
-+ int server,
-+ VCHI_CALLBACK_T callback,
-+ void *callback_param,
-+ int32_t want_crc,
-+ int32_t want_unaligned_bulk_rx,
-+ int32_t want_unaligned_bulk_tx,
-+ VCHI_CONNECTION_SERVICE_HANDLE_T *service_handle );
-+
-+// Routine to close a service
-+typedef int32_t (*VCHI_CONNECTION_SERVICE_DISCONNECT_T)( VCHI_CONNECTION_SERVICE_HANDLE_T service_handle );
-+
-+// Routine to queue a message
-+typedef int32_t (*VCHI_CONNECTION_SERVICE_QUEUE_MESSAGE_T)( VCHI_CONNECTION_SERVICE_HANDLE_T service_handle,
-+ const void *data,
-+ uint32_t data_size,
-+ VCHI_FLAGS_T flags,
-+ void *msg_handle );
-+
-+// scatter-gather (vector) message queueing
-+typedef int32_t (*VCHI_CONNECTION_SERVICE_QUEUE_MESSAGEV_T)( VCHI_CONNECTION_SERVICE_HANDLE_T service_handle,
-+ VCHI_MSG_VECTOR_T *vector,
-+ uint32_t count,
-+ VCHI_FLAGS_T flags,
-+ void *msg_handle );
-+
-+// Routine to dequeue a message
-+typedef int32_t (*VCHI_CONNECTION_SERVICE_DEQUEUE_MESSAGE_T)( VCHI_CONNECTION_SERVICE_HANDLE_T service_handle,
-+ void *data,
-+ uint32_t max_data_size_to_read,
-+ uint32_t *actual_msg_size,
-+ VCHI_FLAGS_T flags );
-+
-+// Routine to peek at a message
-+typedef int32_t (*VCHI_CONNECTION_SERVICE_PEEK_MESSAGE_T)( VCHI_CONNECTION_SERVICE_HANDLE_T service_handle,
-+ void **data,
-+ uint32_t *msg_size,
-+ VCHI_FLAGS_T flags );
-+
-+// Routine to hold a message
-+typedef int32_t (*VCHI_CONNECTION_SERVICE_HOLD_MESSAGE_T)( VCHI_CONNECTION_SERVICE_HANDLE_T service_handle,
-+ void **data,
-+ uint32_t *msg_size,
-+ VCHI_FLAGS_T flags,
-+ void **message_handle );
-+
-+// Routine to initialise a received message iterator
-+typedef int32_t (*VCHI_CONNECTION_SERVICE_LOOKAHEAD_MESSAGE_T)( VCHI_CONNECTION_SERVICE_HANDLE_T service_handle,
-+ VCHI_MSG_ITER_T *iter,
-+ VCHI_FLAGS_T flags );
-+
-+// Routine to release a held message
-+typedef int32_t (*VCHI_CONNECTION_HELD_MSG_RELEASE_T)( VCHI_CONNECTION_SERVICE_HANDLE_T service_handle,
-+ void *message_handle );
-+
-+// Routine to get info on a held message
-+typedef int32_t (*VCHI_CONNECTION_HELD_MSG_INFO_T)( VCHI_CONNECTION_SERVICE_HANDLE_T service_handle,
-+ void *message_handle,
-+ void **data,
-+ int32_t *msg_size,
-+ uint32_t *tx_timestamp,
-+ uint32_t *rx_timestamp );
-+
-+// Routine to check whether the iterator has a next message
-+typedef int32_t (*VCHI_CONNECTION_MSG_ITER_HAS_NEXT_T)( VCHI_CONNECTION_SERVICE_HANDLE_T service,
-+ const VCHI_MSG_ITER_T *iter );
-+
-+// Routine to advance the iterator
-+typedef int32_t (*VCHI_CONNECTION_MSG_ITER_NEXT_T)( VCHI_CONNECTION_SERVICE_HANDLE_T service,
-+ VCHI_MSG_ITER_T *iter,
-+ void **data,
-+ uint32_t *msg_size );
-+
-+// Routine to remove the last message returned by the iterator
-+typedef int32_t (*VCHI_CONNECTION_MSG_ITER_REMOVE_T)( VCHI_CONNECTION_SERVICE_HANDLE_T service,
-+ VCHI_MSG_ITER_T *iter );
-+
-+// Routine to hold the last message returned by the iterator
-+typedef int32_t (*VCHI_CONNECTION_MSG_ITER_HOLD_T)( VCHI_CONNECTION_SERVICE_HANDLE_T service,
-+ VCHI_MSG_ITER_T *iter,
-+ void **msg_handle );
-+
-+// Routine to transmit bulk data
-+typedef int32_t (*VCHI_CONNECTION_BULK_QUEUE_TRANSMIT_T)( VCHI_CONNECTION_SERVICE_HANDLE_T service_handle,
-+ const void *data_src,
-+ uint32_t data_size,
-+ VCHI_FLAGS_T flags,
-+ void *bulk_handle );
-+
-+// Routine to receive data
-+typedef int32_t (*VCHI_CONNECTION_BULK_QUEUE_RECEIVE_T)( VCHI_CONNECTION_SERVICE_HANDLE_T service_handle,
-+ void *data_dst,
-+ uint32_t data_size,
-+ VCHI_FLAGS_T flags,
-+ void *bulk_handle );
-+
-+// Routine to report if a server is available
-+typedef int32_t (*VCHI_CONNECTION_SERVER_PRESENT)( VCHI_CONNECTION_STATE_T *state, int32_t service_id, int32_t peer_flags );
-+
-+// Routine to report the number of RX slots available
-+typedef int (*VCHI_CONNECTION_RX_SLOTS_AVAILABLE)( const VCHI_CONNECTION_STATE_T *state );
-+
-+// Routine to report the RX slot size
-+typedef uint32_t (*VCHI_CONNECTION_RX_SLOT_SIZE)( const VCHI_CONNECTION_STATE_T *state );
-+
-+// Callback to indicate that the other side has added a buffer to the rx bulk DMA FIFO
-+typedef void (*VCHI_CONNECTION_RX_BULK_BUFFER_ADDED)(VCHI_CONNECTION_STATE_T *state,
-+ int32_t service,
-+ uint32_t length,
-+ MESSAGE_TX_CHANNEL_T channel,
-+ uint32_t channel_params,
-+ uint32_t data_length,
-+ uint32_t data_offset);
-+
-+// Callback to inform a service that a Xon or Xoff message has been received
-+typedef void (*VCHI_CONNECTION_FLOW_CONTROL)(VCHI_CONNECTION_STATE_T *state, int32_t service_id, int32_t xoff);
-+
-+// Callback to inform a service that a server available reply message has been received
-+typedef void (*VCHI_CONNECTION_SERVER_AVAILABLE_REPLY)(VCHI_CONNECTION_STATE_T *state, int32_t service_id, uint32_t flags);
-+
-+// Callback to indicate that bulk auxiliary messages have arrived
-+typedef void (*VCHI_CONNECTION_BULK_AUX_RECEIVED)(VCHI_CONNECTION_STATE_T *state);
-+
-+// Callback to indicate that bulk auxiliary messages have arrived
-+typedef void (*VCHI_CONNECTION_BULK_AUX_TRANSMITTED)(VCHI_CONNECTION_STATE_T *state, void *handle);
-+
-+// Callback with all the connection info you require
-+typedef void (*VCHI_CONNECTION_INFO)(VCHI_CONNECTION_STATE_T *state, uint32_t protocol_version, uint32_t slot_size, uint32_t num_slots, uint32_t min_bulk_size);
-+
-+// Callback to inform of a disconnect
-+typedef void (*VCHI_CONNECTION_DISCONNECT)(VCHI_CONNECTION_STATE_T *state, uint32_t flags);
-+
-+// Callback to inform of a power control request
-+typedef void (*VCHI_CONNECTION_POWER_CONTROL)(VCHI_CONNECTION_STATE_T *state, MESSAGE_TX_CHANNEL_T channel, int32_t enable);
-+
-+// allocate memory suitably aligned for this connection
-+typedef void * (*VCHI_BUFFER_ALLOCATE)(VCHI_CONNECTION_SERVICE_HANDLE_T service_handle, uint32_t * length);
-+
-+// free memory allocated by buffer_allocate
-+typedef void (*VCHI_BUFFER_FREE)(VCHI_CONNECTION_SERVICE_HANDLE_T service_handle, void * address);
-+
-+
-+/******************************************************************************
-+ System driver struct
-+ *****************************************************************************/
-+
-+struct opaque_vchi_connection_api_t
-+{
-+ // Routine to init the connection
-+ VCHI_CONNECTION_INIT_T init;
-+
-+ // Connection-level CRC control
-+ VCHI_CONNECTION_CRC_CONTROL_T crc_control;
-+
-+ // Routine to connect to or create service
-+ VCHI_CONNECTION_SERVICE_CONNECT_T service_connect;
-+
-+ // Routine to disconnect from a service
-+ VCHI_CONNECTION_SERVICE_DISCONNECT_T service_disconnect;
-+
-+ // Routine to queue a message
-+ VCHI_CONNECTION_SERVICE_QUEUE_MESSAGE_T service_queue_msg;
-+
-+ // scatter-gather (vector) message queue
-+ VCHI_CONNECTION_SERVICE_QUEUE_MESSAGEV_T service_queue_msgv;
-+
-+ // Routine to dequeue a message
-+ VCHI_CONNECTION_SERVICE_DEQUEUE_MESSAGE_T service_dequeue_msg;
-+
-+ // Routine to peek at a message
-+ VCHI_CONNECTION_SERVICE_PEEK_MESSAGE_T service_peek_msg;
-+
-+ // Routine to hold a message
-+ VCHI_CONNECTION_SERVICE_HOLD_MESSAGE_T service_hold_msg;
-+
-+ // Routine to initialise a received message iterator
-+ VCHI_CONNECTION_SERVICE_LOOKAHEAD_MESSAGE_T service_look_ahead_msg;
-+
-+ // Routine to release a message
-+ VCHI_CONNECTION_HELD_MSG_RELEASE_T held_msg_release;
-+
-+ // Routine to get information on a held message
-+ VCHI_CONNECTION_HELD_MSG_INFO_T held_msg_info;
-+
-+ // Routine to check for next message on iterator
-+ VCHI_CONNECTION_MSG_ITER_HAS_NEXT_T msg_iter_has_next;
-+
-+ // Routine to get next message on iterator
-+ VCHI_CONNECTION_MSG_ITER_NEXT_T msg_iter_next;
-+
-+ // Routine to remove the last message returned by iterator
-+ VCHI_CONNECTION_MSG_ITER_REMOVE_T msg_iter_remove;
-+
-+ // Routine to hold the last message returned by iterator
-+ VCHI_CONNECTION_MSG_ITER_HOLD_T msg_iter_hold;
-+
-+ // Routine to transmit bulk data
-+ VCHI_CONNECTION_BULK_QUEUE_TRANSMIT_T bulk_queue_transmit;
-+
-+ // Routine to receive data
-+ VCHI_CONNECTION_BULK_QUEUE_RECEIVE_T bulk_queue_receive;
-+
-+ // Routine to report the available servers
-+ VCHI_CONNECTION_SERVER_PRESENT server_present;
-+
-+ // Routine to report the number of RX slots available
-+ VCHI_CONNECTION_RX_SLOTS_AVAILABLE connection_rx_slots_available;
-+
-+ // Routine to report the RX slot size
-+ VCHI_CONNECTION_RX_SLOT_SIZE connection_rx_slot_size;
-+
-+ // Callback to indicate that the other side has added a buffer to the rx bulk DMA FIFO
-+ VCHI_CONNECTION_RX_BULK_BUFFER_ADDED rx_bulk_buffer_added;
-+
-+ // Callback to inform a service that a Xon or Xoff message has been received
-+ VCHI_CONNECTION_FLOW_CONTROL flow_control;
-+
-+ // Callback to inform a service that a server available reply message has been received
-+ VCHI_CONNECTION_SERVER_AVAILABLE_REPLY server_available_reply;
-+
-+ // Callback to indicate that bulk auxiliary messages have arrived
-+ VCHI_CONNECTION_BULK_AUX_RECEIVED bulk_aux_received;
-+
-+ // Callback to indicate that a bulk auxiliary message has been transmitted
-+ VCHI_CONNECTION_BULK_AUX_TRANSMITTED bulk_aux_transmitted;
-+
-+ // Callback to provide information about the connection
-+ VCHI_CONNECTION_INFO connection_info;
-+
-+ // Callback to notify that peer has requested disconnect
-+ VCHI_CONNECTION_DISCONNECT disconnect;
-+
-+ // Callback to notify that peer has requested power change
-+ VCHI_CONNECTION_POWER_CONTROL power_control;
-+
-+ // allocate memory suitably aligned for this connection
-+ VCHI_BUFFER_ALLOCATE buffer_allocate;
-+
-+ // free memory allocated by buffer_allocate
-+ VCHI_BUFFER_FREE buffer_free;
-+
-+};
-+
-+struct vchi_connection_t {
-+ const VCHI_CONNECTION_API_T *api;
-+ VCHI_CONNECTION_STATE_T *state;
-+#ifdef VCHI_COARSE_LOCKING
-+ struct semaphore sem;
-+#endif
-+};
-+
-+
-+#endif /* CONNECTION_H_ */
-+
-+/****************************** End of file **********************************/
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchi/message_drivers/message.h
-@@ -0,0 +1,204 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#ifndef _VCHI_MESSAGE_H_
-+#define _VCHI_MESSAGE_H_
-+
-+#include <linux/kernel.h>
-+#include <linux/types.h>
-+#include <linux/semaphore.h>
-+
-+#include "interface/vchi/vchi_cfg_internal.h"
-+#include "interface/vchi/vchi_common.h"
-+
-+
-+typedef enum message_event_type {
-+ MESSAGE_EVENT_NONE,
-+ MESSAGE_EVENT_NOP,
-+ MESSAGE_EVENT_MESSAGE,
-+ MESSAGE_EVENT_SLOT_COMPLETE,
-+ MESSAGE_EVENT_RX_BULK_PAUSED,
-+ MESSAGE_EVENT_RX_BULK_COMPLETE,
-+ MESSAGE_EVENT_TX_COMPLETE,
-+ MESSAGE_EVENT_MSG_DISCARDED
-+} MESSAGE_EVENT_TYPE_T;
-+
-+typedef enum vchi_msg_flags
-+{
-+ VCHI_MSG_FLAGS_NONE = 0x0,
-+ VCHI_MSG_FLAGS_TERMINATE_DMA = 0x1
-+} VCHI_MSG_FLAGS_T;
-+
-+typedef enum message_tx_channel
-+{
-+ MESSAGE_TX_CHANNEL_MESSAGE = 0,
-+ MESSAGE_TX_CHANNEL_BULK = 1 // drivers may provide multiple bulk channels, from 1 upwards
-+} MESSAGE_TX_CHANNEL_T;
-+
-+// Macros used for cycling through bulk channels
-+#define MESSAGE_TX_CHANNEL_BULK_PREV(c) (MESSAGE_TX_CHANNEL_BULK+((c)-MESSAGE_TX_CHANNEL_BULK+VCHI_MAX_BULK_TX_CHANNELS_PER_CONNECTION-1)%VCHI_MAX_BULK_TX_CHANNELS_PER_CONNECTION)
-+#define MESSAGE_TX_CHANNEL_BULK_NEXT(c) (MESSAGE_TX_CHANNEL_BULK+((c)-MESSAGE_TX_CHANNEL_BULK+1)%VCHI_MAX_BULK_TX_CHANNELS_PER_CONNECTION)
-+
-+typedef enum message_rx_channel
-+{
-+ MESSAGE_RX_CHANNEL_MESSAGE = 0,
-+ MESSAGE_RX_CHANNEL_BULK = 1 // drivers may provide multiple bulk channels, from 1 upwards
-+} MESSAGE_RX_CHANNEL_T;
-+
-+// Message receive slot information
-+typedef struct rx_msg_slot_info {
-+
-+ struct rx_msg_slot_info *next;
-+ //struct slot_info *prev;
-+#if !defined VCHI_COARSE_LOCKING
-+ struct semaphore sem;
-+#endif
-+
-+ uint8_t *addr; // base address of slot
-+ uint32_t len; // length of slot in bytes
-+
-+ uint32_t write_ptr; // hardware causes this to advance
-+ uint32_t read_ptr; // this module does the reading
-+ int active; // is this slot in the hardware dma fifo?
-+ uint32_t msgs_parsed; // count how many messages are in this slot
-+ uint32_t msgs_released; // how many messages have been released
-+ void *state; // connection state information
-+ uint8_t ref_count[VCHI_MAX_SERVICES_PER_CONNECTION]; // reference count for slots held by services
-+} RX_MSG_SLOTINFO_T;
-+
-+// The message driver no longer needs to know about the fields of RX_BULK_SLOTINFO_T - sort this out.
-+// In particular, it mustn't use addr and len - they're the client buffer, but the message
-+// driver will be tasked with sending the aligned core section.
-+typedef struct rx_bulk_slotinfo_t {
-+ struct rx_bulk_slotinfo_t *next;
-+
-+ struct semaphore *blocking;
-+
-+ // needed by DMA
-+ void *addr;
-+ uint32_t len;
-+
-+ // needed for the callback
-+ void *service;
-+ void *handle;
-+ VCHI_FLAGS_T flags;
-+} RX_BULK_SLOTINFO_T;
-+
-+
-+/* ----------------------------------------------------------------------
-+ * each connection driver will have a pool of the following struct.
-+ *
-+ * the pool will be managed by vchi_qman_*
-+ * this means there will be multiple queues (single linked lists)
-+ * a given struct message_info will be on exactly one of these queues
-+ * at any one time
-+ * -------------------------------------------------------------------- */
-+typedef struct rx_message_info {
-+
-+ struct message_info *next;
-+ //struct message_info *prev;
-+
-+ uint8_t *addr;
-+ uint32_t len;
-+ RX_MSG_SLOTINFO_T *slot; // points to whichever slot contains this message
-+ uint32_t tx_timestamp;
-+ uint32_t rx_timestamp;
-+
-+} RX_MESSAGE_INFO_T;
-+
-+typedef struct {
-+ MESSAGE_EVENT_TYPE_T type;
-+
-+ struct {
-+ // for messages
-+ void *addr; // address of message
-+ uint16_t slot_delta; // whether this message indicated slot delta
-+ uint32_t len; // length of message
-+ RX_MSG_SLOTINFO_T *slot; // slot this message is in
-+ int32_t service; // service id this message is destined for
-+ uint32_t tx_timestamp; // timestamp from the header
-+ uint32_t rx_timestamp; // timestamp when we parsed it
-+ } message;
-+
-+ // FIXME: cleanup slot reporting...
-+ RX_MSG_SLOTINFO_T *rx_msg;
-+ RX_BULK_SLOTINFO_T *rx_bulk;
-+ void *tx_handle;
-+ MESSAGE_TX_CHANNEL_T tx_channel;
-+
-+} MESSAGE_EVENT_T;
-+
-+
-+// callbacks
-+typedef void VCHI_MESSAGE_DRIVER_EVENT_CALLBACK_T( void *state );
-+
-+typedef struct {
-+ VCHI_MESSAGE_DRIVER_EVENT_CALLBACK_T *event_callback;
-+} VCHI_MESSAGE_DRIVER_OPEN_T;
-+
-+
-+// handle to this instance of message driver (as returned by ->open)
-+typedef struct opaque_mhandle_t *VCHI_MDRIVER_HANDLE_T;
-+
-+struct opaque_vchi_message_driver_t {
-+ VCHI_MDRIVER_HANDLE_T *(*open)( VCHI_MESSAGE_DRIVER_OPEN_T *params, void *state );
-+ int32_t (*suspending)( VCHI_MDRIVER_HANDLE_T *handle );
-+ int32_t (*resumed)( VCHI_MDRIVER_HANDLE_T *handle );
-+ int32_t (*power_control)( VCHI_MDRIVER_HANDLE_T *handle, MESSAGE_TX_CHANNEL_T, int32_t enable );
-+ int32_t (*add_msg_rx_slot)( VCHI_MDRIVER_HANDLE_T *handle, RX_MSG_SLOTINFO_T *slot ); // rx message
-+ int32_t (*add_bulk_rx)( VCHI_MDRIVER_HANDLE_T *handle, void *data, uint32_t len, RX_BULK_SLOTINFO_T *slot ); // rx data (bulk)
-+ int32_t (*send)( VCHI_MDRIVER_HANDLE_T *handle, MESSAGE_TX_CHANNEL_T channel, const void *data, uint32_t len, VCHI_MSG_FLAGS_T flags, void *send_handle ); // tx (message & bulk)
-+ void (*next_event)( VCHI_MDRIVER_HANDLE_T *handle, MESSAGE_EVENT_T *event ); // get the next event from message_driver
-+ int32_t (*enable)( VCHI_MDRIVER_HANDLE_T *handle );
-+ int32_t (*form_message)( VCHI_MDRIVER_HANDLE_T *handle, int32_t service_id, VCHI_MSG_VECTOR_T *vector, uint32_t count, void
-+ *address, uint32_t length_avail, uint32_t max_total_length, int32_t pad_to_fill, int32_t allow_partial );
-+
-+ int32_t (*update_message)( VCHI_MDRIVER_HANDLE_T *handle, void *dest, int16_t *slot_count );
-+ int32_t (*buffer_aligned)( VCHI_MDRIVER_HANDLE_T *handle, int tx, int uncached, const void *address, const uint32_t length );
-+ void * (*allocate_buffer)( VCHI_MDRIVER_HANDLE_T *handle, uint32_t *length );
-+ void (*free_buffer)( VCHI_MDRIVER_HANDLE_T *handle, void *address );
-+ int (*rx_slot_size)( VCHI_MDRIVER_HANDLE_T *handle, int msg_size );
-+ int (*tx_slot_size)( VCHI_MDRIVER_HANDLE_T *handle, int msg_size );
-+
-+ int32_t (*tx_supports_terminate)( const VCHI_MDRIVER_HANDLE_T *handle, MESSAGE_TX_CHANNEL_T channel );
-+ uint32_t (*tx_bulk_chunk_size)( const VCHI_MDRIVER_HANDLE_T *handle, MESSAGE_TX_CHANNEL_T channel );
-+ int (*tx_alignment)( const VCHI_MDRIVER_HANDLE_T *handle, MESSAGE_TX_CHANNEL_T channel );
-+ int (*rx_alignment)( const VCHI_MDRIVER_HANDLE_T *handle, MESSAGE_RX_CHANNEL_T channel );
-+ void (*form_bulk_aux)( VCHI_MDRIVER_HANDLE_T *handle, MESSAGE_TX_CHANNEL_T channel, const void *data, uint32_t len, uint32_t chunk_size, const void **aux_data, int32_t *aux_len );
-+ void (*debug)( VCHI_MDRIVER_HANDLE_T *handle );
-+};
-+
-+
-+#endif // _VCHI_MESSAGE_H_
-+
-+/****************************** End of file ***********************************/
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchi/vchi.h
-@@ -0,0 +1,378 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#ifndef VCHI_H_
-+#define VCHI_H_
-+
-+#include "interface/vchi/vchi_cfg.h"
-+#include "interface/vchi/vchi_common.h"
-+#include "interface/vchi/connections/connection.h"
-+#include "vchi_mh.h"
-+
-+
-+/******************************************************************************
-+ Global defs
-+ *****************************************************************************/
-+
-+#define VCHI_BULK_ROUND_UP(x) ((((unsigned long)(x))+VCHI_BULK_ALIGN-1) & ~(VCHI_BULK_ALIGN-1))
-+#define VCHI_BULK_ROUND_DOWN(x) (((unsigned long)(x)) & ~(VCHI_BULK_ALIGN-1))
-+#define VCHI_BULK_ALIGN_NBYTES(x) (VCHI_BULK_ALIGNED(x) ? 0 : (VCHI_BULK_ALIGN - ((unsigned long)(x) & (VCHI_BULK_ALIGN-1))))
-+
-+#ifdef USE_VCHIQ_ARM
-+#define VCHI_BULK_ALIGNED(x) 1
-+#else
-+#define VCHI_BULK_ALIGNED(x) (((unsigned long)(x) & (VCHI_BULK_ALIGN-1)) == 0)
-+#endif
-+
-+struct vchi_version {
-+ uint32_t version;
-+ uint32_t version_min;
-+};
-+#define VCHI_VERSION(v_) { v_, v_ }
-+#define VCHI_VERSION_EX(v_, m_) { v_, m_ }
-+
-+typedef enum
-+{
-+ VCHI_VEC_POINTER,
-+ VCHI_VEC_HANDLE,
-+ VCHI_VEC_LIST
-+} VCHI_MSG_VECTOR_TYPE_T;
-+
-+typedef struct vchi_msg_vector_ex {
-+
-+ VCHI_MSG_VECTOR_TYPE_T type;
-+ union
-+ {
-+ // a memory handle
-+ struct
-+ {
-+ VCHI_MEM_HANDLE_T handle;
-+ uint32_t offset;
-+ int32_t vec_len;
-+ } handle;
-+
-+ // an ordinary data pointer
-+ struct
-+ {
-+ const void *vec_base;
-+ int32_t vec_len;
-+ } ptr;
-+
-+ // a nested vector list
-+ struct
-+ {
-+ struct vchi_msg_vector_ex *vec;
-+ uint32_t vec_len;
-+ } list;
-+ } u;
-+} VCHI_MSG_VECTOR_EX_T;
-+
-+
-+// Construct an entry in a msg vector for a pointer (p) of length (l)
-+#define VCHI_VEC_POINTER(p,l) VCHI_VEC_POINTER, { { (VCHI_MEM_HANDLE_T)(p), (l) } }
-+
-+// Construct an entry in a msg vector for a message handle (h), starting at offset (o) of length (l)
-+#define VCHI_VEC_HANDLE(h,o,l) VCHI_VEC_HANDLE, { { (h), (o), (l) } }
-+
-+// Macros to manipulate 'FOURCC' values
-+#define MAKE_FOURCC(x) ((int32_t)( (x[0] << 24) | (x[1] << 16) | (x[2] << 8) | x[3] ))
-+#define FOURCC_TO_CHAR(x) (x >> 24) & 0xFF,(x >> 16) & 0xFF,(x >> 8) & 0xFF, x & 0xFF
-+
-+
-+// Opaque service information
-+struct opaque_vchi_service_t;
-+
-+// Descriptor for a held message. Allocated by client, initialised by vchi_msg_hold,
-+// vchi_msg_iter_hold or vchi_msg_iter_hold_next. Fields are for internal VCHI use only.
-+typedef struct
-+{
-+ struct opaque_vchi_service_t *service;
-+ void *message;
-+} VCHI_HELD_MSG_T;
-+
-+
-+
-+// structure used to provide the information needed to open a server or a client
-+typedef struct {
-+ struct vchi_version version;
-+ int32_t service_id;
-+ VCHI_CONNECTION_T *connection;
-+ uint32_t rx_fifo_size;
-+ uint32_t tx_fifo_size;
-+ VCHI_CALLBACK_T callback;
-+ void *callback_param;
-+ /* client intends to receive bulk transfers of
-+ odd lengths or into unaligned buffers */
-+ int32_t want_unaligned_bulk_rx;
-+ /* client intends to transmit bulk transfers of
-+ odd lengths or out of unaligned buffers */
-+ int32_t want_unaligned_bulk_tx;
-+ /* client wants to check CRCs on (bulk) xfers.
-+ Only needs to be set at 1 end - will do both directions. */
-+ int32_t want_crc;
-+} SERVICE_CREATION_T;
-+
-+// Opaque handle for a VCHI instance
-+typedef struct opaque_vchi_instance_handle_t *VCHI_INSTANCE_T;
-+
-+// Opaque handle for a server or client
-+typedef struct opaque_vchi_service_handle_t *VCHI_SERVICE_HANDLE_T;
-+
-+// Service registration & startup
-+typedef void (*VCHI_SERVICE_INIT)(VCHI_INSTANCE_T initialise_instance, VCHI_CONNECTION_T **connections, uint32_t num_connections);
-+
-+typedef struct service_info_tag {
-+ const char * const vll_filename; /* VLL to load to start this service. This is an empty string if VLL is "static" */
-+ VCHI_SERVICE_INIT init; /* Service initialisation function */
-+ void *vll_handle; /* VLL handle; NULL when unloaded or a "static VLL" in build */
-+} SERVICE_INFO_T;
-+
-+/******************************************************************************
-+ Global funcs - implementation is specific to which side you are on (local / remote)
-+ *****************************************************************************/
-+
-+#ifdef __cplusplus
-+extern "C" {
-+#endif
-+
-+extern /*@observer@*/ VCHI_CONNECTION_T * vchi_create_connection( const VCHI_CONNECTION_API_T * function_table,
-+ const VCHI_MESSAGE_DRIVER_T * low_level);
-+
-+
-+// Routine used to initialise the vchi on both local + remote connections
-+extern int32_t vchi_initialise( VCHI_INSTANCE_T *instance_handle );
-+
-+extern int32_t vchi_exit( void );
-+
-+extern int32_t vchi_connect( VCHI_CONNECTION_T **connections,
-+ const uint32_t num_connections,
-+ VCHI_INSTANCE_T instance_handle );
-+
-+//When this is called, ensure that all services have no data pending.
-+//Bulk transfers can remain 'queued'
-+extern int32_t vchi_disconnect( VCHI_INSTANCE_T instance_handle );
-+
-+// Global control over bulk CRC checking
-+extern int32_t vchi_crc_control( VCHI_CONNECTION_T *connection,
-+ VCHI_CRC_CONTROL_T control );
-+
-+// helper functions
-+extern void * vchi_allocate_buffer(VCHI_SERVICE_HANDLE_T handle, uint32_t *length);
-+extern void vchi_free_buffer(VCHI_SERVICE_HANDLE_T handle, void *address);
-+extern uint32_t vchi_current_time(VCHI_INSTANCE_T instance_handle);
-+
-+
-+/******************************************************************************
-+ Global service API
-+ *****************************************************************************/
-+// Routine to create a named service
-+extern int32_t vchi_service_create( VCHI_INSTANCE_T instance_handle,
-+ SERVICE_CREATION_T *setup,
-+ VCHI_SERVICE_HANDLE_T *handle );
-+
-+// Routine to destory a service
-+extern int32_t vchi_service_destroy( const VCHI_SERVICE_HANDLE_T handle );
-+
-+// Routine to open a named service
-+extern int32_t vchi_service_open( VCHI_INSTANCE_T instance_handle,
-+ SERVICE_CREATION_T *setup,
-+ VCHI_SERVICE_HANDLE_T *handle);
-+
-+extern int32_t vchi_get_peer_version( const VCHI_SERVICE_HANDLE_T handle,
-+ short *peer_version );
-+
-+// Routine to close a named service
-+extern int32_t vchi_service_close( const VCHI_SERVICE_HANDLE_T handle );
-+
-+// Routine to increment ref count on a named service
-+extern int32_t vchi_service_use( const VCHI_SERVICE_HANDLE_T handle );
-+
-+// Routine to decrement ref count on a named service
-+extern int32_t vchi_service_release( const VCHI_SERVICE_HANDLE_T handle );
-+
-+// Routine to set a control option for a named service
-+extern int32_t vchi_service_set_option( const VCHI_SERVICE_HANDLE_T handle,
-+ VCHI_SERVICE_OPTION_T option,
-+ int value);
-+
-+// Routine to send a message across a service
-+extern int32_t vchi_msg_queue( VCHI_SERVICE_HANDLE_T handle,
-+ const void *data,
-+ uint32_t data_size,
-+ VCHI_FLAGS_T flags,
-+ void *msg_handle );
-+
-+// scatter-gather (vector) and send message
-+int32_t vchi_msg_queuev_ex( VCHI_SERVICE_HANDLE_T handle,
-+ VCHI_MSG_VECTOR_EX_T *vector,
-+ uint32_t count,
-+ VCHI_FLAGS_T flags,
-+ void *msg_handle );
-+
-+// legacy scatter-gather (vector) and send message, only handles pointers
-+int32_t vchi_msg_queuev( VCHI_SERVICE_HANDLE_T handle,
-+ VCHI_MSG_VECTOR_T *vector,
-+ uint32_t count,
-+ VCHI_FLAGS_T flags,
-+ void *msg_handle );
-+
-+// Routine to receive a msg from a service
-+// Dequeue is equivalent to hold, copy into client buffer, release
-+extern int32_t vchi_msg_dequeue( VCHI_SERVICE_HANDLE_T handle,
-+ void *data,
-+ uint32_t max_data_size_to_read,
-+ uint32_t *actual_msg_size,
-+ VCHI_FLAGS_T flags );
-+
-+// Routine to look at a message in place.
-+// The message is not dequeued, so a subsequent call to peek or dequeue
-+// will return the same message.
-+extern int32_t vchi_msg_peek( VCHI_SERVICE_HANDLE_T handle,
-+ void **data,
-+ uint32_t *msg_size,
-+ VCHI_FLAGS_T flags );
-+
-+// Routine to remove a message after it has been read in place with peek
-+// The first message on the queue is dequeued.
-+extern int32_t vchi_msg_remove( VCHI_SERVICE_HANDLE_T handle );
-+
-+// Routine to look at a message in place.
-+// The message is dequeued, so the caller is left holding it; the descriptor is
-+// filled in and must be released when the user has finished with the message.
-+extern int32_t vchi_msg_hold( VCHI_SERVICE_HANDLE_T handle,
-+ void **data, // } may be NULL, as info can be
-+ uint32_t *msg_size, // } obtained from HELD_MSG_T
-+ VCHI_FLAGS_T flags,
-+ VCHI_HELD_MSG_T *message_descriptor );
-+
-+// Initialise an iterator to look through messages in place
-+extern int32_t vchi_msg_look_ahead( VCHI_SERVICE_HANDLE_T handle,
-+ VCHI_MSG_ITER_T *iter,
-+ VCHI_FLAGS_T flags );
-+
-+/******************************************************************************
-+ Global service support API - operations on held messages and message iterators
-+ *****************************************************************************/
-+
-+// Routine to get the address of a held message
-+extern void *vchi_held_msg_ptr( const VCHI_HELD_MSG_T *message );
-+
-+// Routine to get the size of a held message
-+extern int32_t vchi_held_msg_size( const VCHI_HELD_MSG_T *message );
-+
-+// Routine to get the transmit timestamp as written into the header by the peer
-+extern uint32_t vchi_held_msg_tx_timestamp( const VCHI_HELD_MSG_T *message );
-+
-+// Routine to get the reception timestamp, written as we parsed the header
-+extern uint32_t vchi_held_msg_rx_timestamp( const VCHI_HELD_MSG_T *message );
-+
-+// Routine to release a held message after it has been processed
-+extern int32_t vchi_held_msg_release( VCHI_HELD_MSG_T *message );
-+
-+// Indicates whether the iterator has a next message.
-+extern int32_t vchi_msg_iter_has_next( const VCHI_MSG_ITER_T *iter );
-+
-+// Return the pointer and length for the next message and advance the iterator.
-+extern int32_t vchi_msg_iter_next( VCHI_MSG_ITER_T *iter,
-+ void **data,
-+ uint32_t *msg_size );
-+
-+// Remove the last message returned by vchi_msg_iter_next.
-+// Can only be called once after each call to vchi_msg_iter_next.
-+extern int32_t vchi_msg_iter_remove( VCHI_MSG_ITER_T *iter );
-+
-+// Hold the last message returned by vchi_msg_iter_next.
-+// Can only be called once after each call to vchi_msg_iter_next.
-+extern int32_t vchi_msg_iter_hold( VCHI_MSG_ITER_T *iter,
-+ VCHI_HELD_MSG_T *message );
-+
-+// Return information for the next message, and hold it, advancing the iterator.
-+extern int32_t vchi_msg_iter_hold_next( VCHI_MSG_ITER_T *iter,
-+ void **data, // } may be NULL
-+ uint32_t *msg_size, // }
-+ VCHI_HELD_MSG_T *message );
-+
-+
-+/******************************************************************************
-+ Global bulk API
-+ *****************************************************************************/
-+
-+// Routine to prepare interface for a transfer from the other side
-+extern int32_t vchi_bulk_queue_receive( VCHI_SERVICE_HANDLE_T handle,
-+ void *data_dst,
-+ uint32_t data_size,
-+ VCHI_FLAGS_T flags,
-+ void *transfer_handle );
-+
-+
-+// Prepare interface for a transfer from the other side into relocatable memory.
-+int32_t vchi_bulk_queue_receive_reloc( const VCHI_SERVICE_HANDLE_T handle,
-+ VCHI_MEM_HANDLE_T h_dst,
-+ uint32_t offset,
-+ uint32_t data_size,
-+ const VCHI_FLAGS_T flags,
-+ void * const bulk_handle );
-+
-+// Routine to queue up data ready for transfer to the other (once they have signalled they are ready)
-+extern int32_t vchi_bulk_queue_transmit( VCHI_SERVICE_HANDLE_T handle,
-+ const void *data_src,
-+ uint32_t data_size,
-+ VCHI_FLAGS_T flags,
-+ void *transfer_handle );
-+
-+
-+/******************************************************************************
-+ Configuration plumbing
-+ *****************************************************************************/
-+
-+// function prototypes for the different mid layers (the state info gives the different physical connections)
-+extern const VCHI_CONNECTION_API_T *single_get_func_table( void );
-+//extern const VCHI_CONNECTION_API_T *local_server_get_func_table( void );
-+//extern const VCHI_CONNECTION_API_T *local_client_get_func_table( void );
-+
-+// declare all message drivers here
-+const VCHI_MESSAGE_DRIVER_T *vchi_mphi_message_driver_func_table( void );
-+
-+#ifdef __cplusplus
-+}
-+#endif
-+
-+extern int32_t vchi_bulk_queue_transmit_reloc( VCHI_SERVICE_HANDLE_T handle,
-+ VCHI_MEM_HANDLE_T h_src,
-+ uint32_t offset,
-+ uint32_t data_size,
-+ VCHI_FLAGS_T flags,
-+ void *transfer_handle );
-+#endif /* VCHI_H_ */
-+
-+/****************************** End of file **********************************/
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchi/vchi_cfg.h
-@@ -0,0 +1,224 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#ifndef VCHI_CFG_H_
-+#define VCHI_CFG_H_
-+
-+/****************************************************************************************
-+ * Defines in this first section are part of the VCHI API and may be examined by VCHI
-+ * services.
-+ ***************************************************************************************/
-+
-+/* Required alignment of base addresses for bulk transfer, if unaligned transfers are not enabled */
-+/* Really determined by the message driver, and should be available from a run-time call. */
-+#ifndef VCHI_BULK_ALIGN
-+# if __VCCOREVER__ >= 0x04000000
-+# define VCHI_BULK_ALIGN 32 // Allows for the need to do cache cleans
-+# else
-+# define VCHI_BULK_ALIGN 16
-+# endif
-+#endif
-+
-+/* Required length multiple for bulk transfers, if unaligned transfers are not enabled */
-+/* May be less than or greater than VCHI_BULK_ALIGN */
-+/* Really determined by the message driver, and should be available from a run-time call. */
-+#ifndef VCHI_BULK_GRANULARITY
-+# if __VCCOREVER__ >= 0x04000000
-+# define VCHI_BULK_GRANULARITY 32 // Allows for the need to do cache cleans
-+# else
-+# define VCHI_BULK_GRANULARITY 16
-+# endif
-+#endif
-+
-+/* The largest possible message to be queued with vchi_msg_queue. */
-+#ifndef VCHI_MAX_MSG_SIZE
-+# if defined VCHI_LOCAL_HOST_PORT
-+# define VCHI_MAX_MSG_SIZE 16384 // makes file transfers fast, but should they be using bulk?
-+# else
-+# define VCHI_MAX_MSG_SIZE 4096 // NOTE: THIS MUST BE LARGER THAN OR EQUAL TO THE SIZE OF THE KHRONOS MERGE BUFFER!!
-+# endif
-+#endif
-+
-+/******************************************************************************************
-+ * Defines below are system configuration options, and should not be used by VCHI services.
-+ *****************************************************************************************/
-+
-+/* How many connections can we support? A localhost implementation uses 2 connections,
-+ * 1 for host-app, 1 for VMCS, and these are hooked together by a loopback MPHI VCFW
-+ * driver. */
-+#ifndef VCHI_MAX_NUM_CONNECTIONS
-+# define VCHI_MAX_NUM_CONNECTIONS 3
-+#endif
-+
-+/* How many services can we open per connection? Extending this doesn't cost processing time, just a small
-+ * amount of static memory. */
-+#ifndef VCHI_MAX_SERVICES_PER_CONNECTION
-+# define VCHI_MAX_SERVICES_PER_CONNECTION 36
-+#endif
-+
-+/* Adjust if using a message driver that supports more logical TX channels */
-+#ifndef VCHI_MAX_BULK_TX_CHANNELS_PER_CONNECTION
-+# define VCHI_MAX_BULK_TX_CHANNELS_PER_CONNECTION 9 // 1 MPHI + 8 CCP2 logical channels
-+#endif
-+
-+/* Adjust if using a message driver that supports more logical RX channels */
-+#ifndef VCHI_MAX_BULK_RX_CHANNELS_PER_CONNECTION
-+# define VCHI_MAX_BULK_RX_CHANNELS_PER_CONNECTION 1 // 1 MPHI
-+#endif
-+
-+/* How many receive slots do we use. This times VCHI_MAX_MSG_SIZE gives the effective
-+ * receive queue space, less message headers. */
-+#ifndef VCHI_NUM_READ_SLOTS
-+# if defined(VCHI_LOCAL_HOST_PORT)
-+# define VCHI_NUM_READ_SLOTS 4
-+# else
-+# define VCHI_NUM_READ_SLOTS 48
-+# endif
-+#endif
-+
-+/* Do we utilise overrun facility for receive message slots? Can aid peer transmit
-+ * performance. Only define on VideoCore end, talking to host.
-+ */
-+//#define VCHI_MSG_RX_OVERRUN
-+
-+/* How many transmit slots do we use. Generally don't need many, as the hardware driver
-+ * underneath VCHI will usually have its own buffering. */
-+#ifndef VCHI_NUM_WRITE_SLOTS
-+# define VCHI_NUM_WRITE_SLOTS 4
-+#endif
-+
-+/* If a service has held or queued received messages in VCHI_XOFF_THRESHOLD or more slots,
-+ * then it's taking up too much buffer space, and the peer service will be told to stop
-+ * transmitting with an XOFF message. For this to be effective, the VCHI_NUM_READ_SLOTS
-+ * needs to be considerably bigger than VCHI_NUM_WRITE_SLOTS, or the transmit latency
-+ * is too high. */
-+#ifndef VCHI_XOFF_THRESHOLD
-+# define VCHI_XOFF_THRESHOLD (VCHI_NUM_READ_SLOTS / 2)
-+#endif
-+
-+/* After we've sent an XOFF, the peer will be told to resume transmission once the local
-+ * service has dequeued/released enough messages that it's now occupying
-+ * VCHI_XON_THRESHOLD slots or fewer. */
-+#ifndef VCHI_XON_THRESHOLD
-+# define VCHI_XON_THRESHOLD (VCHI_NUM_READ_SLOTS / 4)
-+#endif
-+
-+/* A size below which a bulk transfer omits the handshake completely and always goes
-+ * via the message channel, if bulk auxiliary is being sent on that service. (The user
-+ * can guarantee this by enabling unaligned transmits).
-+ * Not API. */
-+#ifndef VCHI_MIN_BULK_SIZE
-+# define VCHI_MIN_BULK_SIZE ( VCHI_MAX_MSG_SIZE / 2 < 4096 ? VCHI_MAX_MSG_SIZE / 2 : 4096 )
-+#endif
-+
-+/* Maximum size of bulk transmission chunks, for each interface type. A trade-off between
-+ * speed and latency; the smaller the chunk size the better change of messages and other
-+ * bulk transmissions getting in when big bulk transfers are happening. Set to 0 to not
-+ * break transmissions into chunks.
-+ */
-+#ifndef VCHI_MAX_BULK_CHUNK_SIZE_MPHI
-+# define VCHI_MAX_BULK_CHUNK_SIZE_MPHI (16 * 1024)
-+#endif
-+
-+/* NB Chunked CCP2 transmissions violate the letter of the CCP2 spec by using "JPEG8" mode
-+ * with multiple-line frames. Only use if the receiver can cope. */
-+#ifndef VCHI_MAX_BULK_CHUNK_SIZE_CCP2
-+# define VCHI_MAX_BULK_CHUNK_SIZE_CCP2 0
-+#endif
-+
-+/* How many TX messages can we have pending in our transmit slots. Once exhausted,
-+ * vchi_msg_queue will be blocked. */
-+#ifndef VCHI_TX_MSG_QUEUE_SIZE
-+# define VCHI_TX_MSG_QUEUE_SIZE 256
-+#endif
-+
-+/* How many RX messages can we have parsed in the receive slots. Once exhausted, parsing
-+ * will be suspended until older messages are dequeued/released. */
-+#ifndef VCHI_RX_MSG_QUEUE_SIZE
-+# define VCHI_RX_MSG_QUEUE_SIZE 256
-+#endif
-+
-+/* Really should be able to cope if we run out of received message descriptors, by
-+ * suspending parsing as the comment above says, but we don't. This sweeps the issue
-+ * under the carpet. */
-+#if VCHI_RX_MSG_QUEUE_SIZE < (VCHI_MAX_MSG_SIZE/16 + 1) * VCHI_NUM_READ_SLOTS
-+# undef VCHI_RX_MSG_QUEUE_SIZE
-+# define VCHI_RX_MSG_QUEUE_SIZE (VCHI_MAX_MSG_SIZE/16 + 1) * VCHI_NUM_READ_SLOTS
-+#endif
-+
-+/* How many bulk transmits can we have pending. Once exhausted, vchi_bulk_queue_transmit
-+ * will be blocked. */
-+#ifndef VCHI_TX_BULK_QUEUE_SIZE
-+# define VCHI_TX_BULK_QUEUE_SIZE 64
-+#endif
-+
-+/* How many bulk receives can we have pending. Once exhausted, vchi_bulk_queue_receive
-+ * will be blocked. */
-+#ifndef VCHI_RX_BULK_QUEUE_SIZE
-+# define VCHI_RX_BULK_QUEUE_SIZE 64
-+#endif
-+
-+/* A limit on how many outstanding bulk requests we expect the peer to give us. If
-+ * the peer asks for more than this, VCHI will fail and assert. The number is determined
-+ * by the peer's hardware - it's the number of outstanding requests that can be queued
-+ * on all bulk channels. VC3's MPHI peripheral allows 16. */
-+#ifndef VCHI_MAX_PEER_BULK_REQUESTS
-+# define VCHI_MAX_PEER_BULK_REQUESTS 32
-+#endif
-+
-+/* Define VCHI_CCP2TX_MANUAL_POWER if the host tells us when to turn the CCP2
-+ * transmitter on and off.
-+ */
-+/*#define VCHI_CCP2TX_MANUAL_POWER*/
-+
-+#ifndef VCHI_CCP2TX_MANUAL_POWER
-+
-+/* Timeout (in milliseconds) for putting the CCP2TX interface into IDLE state. Set
-+ * negative for no IDLE.
-+ */
-+# ifndef VCHI_CCP2TX_IDLE_TIMEOUT
-+# define VCHI_CCP2TX_IDLE_TIMEOUT 5
-+# endif
-+
-+/* Timeout (in milliseconds) for putting the CCP2TX interface into OFF state. Set
-+ * negative for no OFF.
-+ */
-+# ifndef VCHI_CCP2TX_OFF_TIMEOUT
-+# define VCHI_CCP2TX_OFF_TIMEOUT 1000
-+# endif
-+
-+#endif /* VCHI_CCP2TX_MANUAL_POWER */
-+
-+#endif /* VCHI_CFG_H_ */
-+
-+/****************************** End of file **********************************/
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchi/vchi_cfg_internal.h
-@@ -0,0 +1,71 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#ifndef VCHI_CFG_INTERNAL_H_
-+#define VCHI_CFG_INTERNAL_H_
-+
-+/****************************************************************************************
-+ * Control optimisation attempts.
-+ ***************************************************************************************/
-+
-+// Don't use lots of short-term locks - use great long ones, reducing the overall locks-per-second
-+#define VCHI_COARSE_LOCKING
-+
-+// Avoid lock then unlock on exit from blocking queue operations (msg tx, bulk rx/tx)
-+// (only relevant if VCHI_COARSE_LOCKING)
-+#define VCHI_ELIDE_BLOCK_EXIT_LOCK
-+
-+// Avoid lock on non-blocking peek
-+// (only relevant if VCHI_COARSE_LOCKING)
-+#define VCHI_AVOID_PEEK_LOCK
-+
-+// Use one slot-handler thread per connection, rather than 1 thread dealing with all connections in rotation.
-+#define VCHI_MULTIPLE_HANDLER_THREADS
-+
-+// Put free descriptors onto the head of the free queue, rather than the tail, so that we don't thrash
-+// our way through the pool of descriptors.
-+#define VCHI_PUSH_FREE_DESCRIPTORS_ONTO_HEAD
-+
-+// Don't issue a MSG_AVAILABLE callback for every single message. Possibly only safe if VCHI_COARSE_LOCKING.
-+#define VCHI_FEWER_MSG_AVAILABLE_CALLBACKS
-+
-+// Don't use message descriptors for TX messages that don't need them
-+#define VCHI_MINIMISE_TX_MSG_DESCRIPTORS
-+
-+// Nano-locks for multiqueue
-+//#define VCHI_MQUEUE_NANOLOCKS
-+
-+// Lock-free(er) dequeuing
-+//#define VCHI_RX_NANOLOCKS
-+
-+#endif /*VCHI_CFG_INTERNAL_H_*/
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchi/vchi_common.h
-@@ -0,0 +1,175 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#ifndef VCHI_COMMON_H_
-+#define VCHI_COMMON_H_
-+
-+
-+//flags used when sending messages (must be bitmapped)
-+typedef enum
-+{
-+ VCHI_FLAGS_NONE = 0x0,
-+ VCHI_FLAGS_BLOCK_UNTIL_OP_COMPLETE = 0x1, // waits for message to be received, or sent (NB. not the same as being seen on other side)
-+ VCHI_FLAGS_CALLBACK_WHEN_OP_COMPLETE = 0x2, // run a callback when message sent
-+ VCHI_FLAGS_BLOCK_UNTIL_QUEUED = 0x4, // return once the transfer is in a queue ready to go
-+ VCHI_FLAGS_ALLOW_PARTIAL = 0x8,
-+ VCHI_FLAGS_BLOCK_UNTIL_DATA_READ = 0x10,
-+ VCHI_FLAGS_CALLBACK_WHEN_DATA_READ = 0x20,
-+
-+ VCHI_FLAGS_ALIGN_SLOT = 0x000080, // internal use only
-+ VCHI_FLAGS_BULK_AUX_QUEUED = 0x010000, // internal use only
-+ VCHI_FLAGS_BULK_AUX_COMPLETE = 0x020000, // internal use only
-+ VCHI_FLAGS_BULK_DATA_QUEUED = 0x040000, // internal use only
-+ VCHI_FLAGS_BULK_DATA_COMPLETE = 0x080000, // internal use only
-+ VCHI_FLAGS_INTERNAL = 0xFF0000
-+} VCHI_FLAGS_T;
-+
-+// constants for vchi_crc_control()
-+typedef enum {
-+ VCHI_CRC_NOTHING = -1,
-+ VCHI_CRC_PER_SERVICE = 0,
-+ VCHI_CRC_EVERYTHING = 1,
-+} VCHI_CRC_CONTROL_T;
-+
-+//callback reasons when an event occurs on a service
-+typedef enum
-+{
-+ VCHI_CALLBACK_REASON_MIN,
-+
-+ //This indicates that there is data available
-+ //handle is the msg id that was transmitted with the data
-+ // When a message is received and there was no FULL message available previously, send callback
-+ // Tasks get kicked by the callback, reset their event and try and read from the fifo until it fails
-+ VCHI_CALLBACK_MSG_AVAILABLE,
-+ VCHI_CALLBACK_MSG_SENT,
-+ VCHI_CALLBACK_MSG_SPACE_AVAILABLE, // XXX not yet implemented
-+
-+ // This indicates that a transfer from the other side has completed
-+ VCHI_CALLBACK_BULK_RECEIVED,
-+ //This indicates that data queued up to be sent has now gone
-+ //handle is the msg id that was used when sending the data
-+ VCHI_CALLBACK_BULK_SENT,
-+ VCHI_CALLBACK_BULK_RX_SPACE_AVAILABLE, // XXX not yet implemented
-+ VCHI_CALLBACK_BULK_TX_SPACE_AVAILABLE, // XXX not yet implemented
-+
-+ VCHI_CALLBACK_SERVICE_CLOSED,
-+
-+ // this side has sent XOFF to peer due to lack of data consumption by service
-+ // (suggests the service may need to take some recovery action if it has
-+ // been deliberately holding off consuming data)
-+ VCHI_CALLBACK_SENT_XOFF,
-+ VCHI_CALLBACK_SENT_XON,
-+
-+ // indicates that a bulk transfer has finished reading the source buffer
-+ VCHI_CALLBACK_BULK_DATA_READ,
-+
-+ // power notification events (currently host side only)
-+ VCHI_CALLBACK_PEER_OFF,
-+ VCHI_CALLBACK_PEER_SUSPENDED,
-+ VCHI_CALLBACK_PEER_ON,
-+ VCHI_CALLBACK_PEER_RESUMED,
-+ VCHI_CALLBACK_FORCED_POWER_OFF,
-+
-+#ifdef USE_VCHIQ_ARM
-+ // some extra notifications provided by vchiq_arm
-+ VCHI_CALLBACK_SERVICE_OPENED,
-+ VCHI_CALLBACK_BULK_RECEIVE_ABORTED,
-+ VCHI_CALLBACK_BULK_TRANSMIT_ABORTED,
-+#endif
-+
-+ VCHI_CALLBACK_REASON_MAX
-+} VCHI_CALLBACK_REASON_T;
-+
-+// service control options
-+typedef enum
-+{
-+ VCHI_SERVICE_OPTION_MIN,
-+
-+ VCHI_SERVICE_OPTION_TRACE,
-+ VCHI_SERVICE_OPTION_SYNCHRONOUS,
-+
-+ VCHI_SERVICE_OPTION_MAX
-+} VCHI_SERVICE_OPTION_T;
-+
-+
-+//Callback used by all services / bulk transfers
-+typedef void (*VCHI_CALLBACK_T)( void *callback_param, //my service local param
-+ VCHI_CALLBACK_REASON_T reason,
-+ void *handle ); //for transmitting msg's only
-+
-+
-+
-+/*
-+ * Define vector struct for scatter-gather (vector) operations
-+ * Vectors can be nested - if a vector element has negative length, then
-+ * the data pointer is treated as pointing to another vector array, with
-+ * '-vec_len' elements. Thus to append a header onto an existing vector,
-+ * you can do this:
-+ *
-+ * void foo(const VCHI_MSG_VECTOR_T *v, int n)
-+ * {
-+ * VCHI_MSG_VECTOR_T nv[2];
-+ * nv[0].vec_base = my_header;
-+ * nv[0].vec_len = sizeof my_header;
-+ * nv[1].vec_base = v;
-+ * nv[1].vec_len = -n;
-+ * ...
-+ *
-+ */
-+typedef struct vchi_msg_vector {
-+ const void *vec_base;
-+ int32_t vec_len;
-+} VCHI_MSG_VECTOR_T;
-+
-+// Opaque type for a connection API
-+typedef struct opaque_vchi_connection_api_t VCHI_CONNECTION_API_T;
-+
-+// Opaque type for a message driver
-+typedef struct opaque_vchi_message_driver_t VCHI_MESSAGE_DRIVER_T;
-+
-+
-+// Iterator structure for reading ahead through received message queue. Allocated by client,
-+// initialised by vchi_msg_look_ahead. Fields are for internal VCHI use only.
-+// Iterates over messages in queue at the instant of the call to vchi_msg_lookahead -
-+// will not proceed to messages received since. Behaviour is undefined if an iterator
-+// is used again after messages for that service are removed/dequeued by any
-+// means other than vchi_msg_iter_... calls on the iterator itself.
-+typedef struct {
-+ struct opaque_vchi_service_t *service;
-+ void *last;
-+ void *next;
-+ void *remove;
-+} VCHI_MSG_ITER_T;
-+
-+
-+#endif // VCHI_COMMON_H_
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchi/vchi_mh.h
-@@ -0,0 +1,42 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#ifndef VCHI_MH_H_
-+#define VCHI_MH_H_
-+
-+#include <linux/types.h>
-+
-+typedef int32_t VCHI_MEM_HANDLE_T;
-+#define VCHI_MEM_HANDLE_INVALID 0
-+
-+#endif
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq.h
-@@ -0,0 +1,40 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#ifndef VCHIQ_VCHIQ_H
-+#define VCHIQ_VCHIQ_H
-+
-+#include "vchiq_if.h"
-+#include "vchiq_util.h"
-+
-+#endif
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_2835.h
-@@ -0,0 +1,42 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#ifndef VCHIQ_2835_H
-+#define VCHIQ_2835_H
-+
-+#include "vchiq_pagelist.h"
-+
-+#define VCHIQ_PLATFORM_FRAGMENTS_OFFSET_IDX 0
-+#define VCHIQ_PLATFORM_FRAGMENTS_COUNT_IDX 1
-+
-+#endif /* VCHIQ_2835_H */
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_2835_arm.c
-@@ -0,0 +1,586 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/types.h>
-+#include <linux/errno.h>
-+#include <linux/interrupt.h>
-+#include <linux/pagemap.h>
-+#include <linux/dma-mapping.h>
-+#include <linux/version.h>
-+#include <linux/io.h>
-+#include <linux/platform_device.h>
-+#include <linux/uaccess.h>
-+#include <linux/of.h>
-+#include <asm/pgtable.h>
-+#include <soc/bcm2835/raspberrypi-firmware.h>
-+
-+#define dmac_map_area __glue(_CACHE,_dma_map_area)
-+#define dmac_unmap_area __glue(_CACHE,_dma_unmap_area)
-+
-+extern void dmac_map_area(const void *, size_t, int);
-+extern void dmac_unmap_area(const void *, size_t, int);
-+
-+#define TOTAL_SLOTS (VCHIQ_SLOT_ZERO_SLOTS + 2 * 32)
-+
-+#define VCHIQ_ARM_ADDRESS(x) ((void *)((char *)x + g_virt_to_bus_offset))
-+
-+#include "vchiq_arm.h"
-+#include "vchiq_2835.h"
-+#include "vchiq_connected.h"
-+#include "vchiq_killable.h"
-+
-+#define MAX_FRAGMENTS (VCHIQ_NUM_CURRENT_BULKS * 2)
-+
-+#define BELL0 0x00
-+#define BELL2 0x08
-+
-+typedef struct vchiq_2835_state_struct {
-+ int inited;
-+ VCHIQ_ARM_STATE_T arm_state;
-+} VCHIQ_2835_ARM_STATE_T;
-+
-+static void __iomem *g_regs;
-+static unsigned int g_cache_line_size = sizeof(CACHE_LINE_SIZE);
-+static unsigned int g_fragments_size;
-+static char *g_fragments_base;
-+static char *g_free_fragments;
-+static struct semaphore g_free_fragments_sema;
-+static unsigned long g_virt_to_bus_offset;
-+
-+extern int vchiq_arm_log_level;
-+
-+static DEFINE_SEMAPHORE(g_free_fragments_mutex);
-+
-+static irqreturn_t
-+vchiq_doorbell_irq(int irq, void *dev_id);
-+
-+static int
-+create_pagelist(char __user *buf, size_t count, unsigned short type,
-+ struct task_struct *task, PAGELIST_T ** ppagelist);
-+
-+static void
-+free_pagelist(PAGELIST_T *pagelist, int actual);
-+
-+int vchiq_platform_init(struct platform_device *pdev, VCHIQ_STATE_T *state)
-+{
-+ struct device *dev = &pdev->dev;
-+ struct rpi_firmware *fw = platform_get_drvdata(pdev);
-+ VCHIQ_SLOT_ZERO_T *vchiq_slot_zero;
-+ struct resource *res;
-+ void *slot_mem;
-+ dma_addr_t slot_phys;
-+ u32 channelbase;
-+ int slot_mem_size, frag_mem_size;
-+ int err, irq, i;
-+
-+ g_virt_to_bus_offset = virt_to_dma(dev, (void *)0);
-+
-+ (void)of_property_read_u32(dev->of_node, "cache-line-size",
-+ &g_cache_line_size);
-+ g_fragments_size = 2 * g_cache_line_size;
-+
-+ /* Allocate space for the channels in coherent memory */
-+ slot_mem_size = PAGE_ALIGN(TOTAL_SLOTS * VCHIQ_SLOT_SIZE);
-+ frag_mem_size = PAGE_ALIGN(g_fragments_size * MAX_FRAGMENTS);
-+
-+ slot_mem = dmam_alloc_coherent(dev, slot_mem_size + frag_mem_size,
-+ &slot_phys, GFP_KERNEL);
-+ if (!slot_mem) {
-+ dev_err(dev, "could not allocate DMA memory\n");
-+ return -ENOMEM;
-+ }
-+
-+ WARN_ON(((int)slot_mem & (PAGE_SIZE - 1)) != 0);
-+
-+ vchiq_slot_zero = vchiq_init_slots(slot_mem, slot_mem_size);
-+ if (!vchiq_slot_zero)
-+ return -EINVAL;
-+
-+ vchiq_slot_zero->platform_data[VCHIQ_PLATFORM_FRAGMENTS_OFFSET_IDX] =
-+ (int)slot_phys + slot_mem_size;
-+ vchiq_slot_zero->platform_data[VCHIQ_PLATFORM_FRAGMENTS_COUNT_IDX] =
-+ MAX_FRAGMENTS;
-+
-+ g_fragments_base = (char *)slot_mem + slot_mem_size;
-+ slot_mem_size += frag_mem_size;
-+
-+ g_free_fragments = g_fragments_base;
-+ for (i = 0; i < (MAX_FRAGMENTS - 1); i++) {
-+ *(char **)&g_fragments_base[i*g_fragments_size] =
-+ &g_fragments_base[(i + 1)*g_fragments_size];
-+ }
-+ *(char **)&g_fragments_base[i * g_fragments_size] = NULL;
-+ sema_init(&g_free_fragments_sema, MAX_FRAGMENTS);
-+
-+ if (vchiq_init_state(state, vchiq_slot_zero, 0) != VCHIQ_SUCCESS)
-+ return -EINVAL;
-+
-+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+ g_regs = devm_ioremap_resource(&pdev->dev, res);
-+ if (IS_ERR(g_regs))
-+ return PTR_ERR(g_regs);
-+
-+ irq = platform_get_irq(pdev, 0);
-+ if (irq <= 0) {
-+ dev_err(dev, "failed to get IRQ\n");
-+ return irq;
-+ }
-+
-+ err = devm_request_irq(dev, irq, vchiq_doorbell_irq, IRQF_IRQPOLL,
-+ "VCHIQ doorbell", state);
-+ if (err) {
-+ dev_err(dev, "failed to register irq=%d\n", irq);
-+ return err;
-+ }
-+
-+ /* Send the base address of the slots to VideoCore */
-+ channelbase = slot_phys;
-+ err = rpi_firmware_property(fw, RPI_FIRMWARE_VCHIQ_INIT,
-+ &channelbase, sizeof(channelbase));
-+ if (err || channelbase) {
-+ dev_err(dev, "failed to set channelbase\n");
-+ return err ? : -ENXIO;
-+ }
-+
-+ vchiq_log_info(vchiq_arm_log_level,
-+ "vchiq_init - done (slots %x, phys %pad)",
-+ (unsigned int)vchiq_slot_zero, &slot_phys);
-+
-+ vchiq_call_connected_callbacks();
-+
-+ return 0;
-+}
-+
-+VCHIQ_STATUS_T
-+vchiq_platform_init_state(VCHIQ_STATE_T *state)
-+{
-+ VCHIQ_STATUS_T status = VCHIQ_SUCCESS;
-+ state->platform_state = kzalloc(sizeof(VCHIQ_2835_ARM_STATE_T), GFP_KERNEL);
-+ ((VCHIQ_2835_ARM_STATE_T*)state->platform_state)->inited = 1;
-+ status = vchiq_arm_init_state(state, &((VCHIQ_2835_ARM_STATE_T*)state->platform_state)->arm_state);
-+ if(status != VCHIQ_SUCCESS)
-+ {
-+ ((VCHIQ_2835_ARM_STATE_T*)state->platform_state)->inited = 0;
-+ }
-+ return status;
-+}
-+
-+VCHIQ_ARM_STATE_T*
-+vchiq_platform_get_arm_state(VCHIQ_STATE_T *state)
-+{
-+ if(!((VCHIQ_2835_ARM_STATE_T*)state->platform_state)->inited)
-+ {
-+ BUG();
-+ }
-+ return &((VCHIQ_2835_ARM_STATE_T*)state->platform_state)->arm_state;
-+}
-+
-+void
-+remote_event_signal(REMOTE_EVENT_T *event)
-+{
-+ wmb();
-+
-+ event->fired = 1;
-+
-+ dsb(); /* data barrier operation */
-+
-+ if (event->armed)
-+ writel(0, g_regs + BELL2); /* trigger vc interrupt */
-+}
-+
-+int
-+vchiq_copy_from_user(void *dst, const void *src, int size)
-+{
-+ if ((uint32_t)src < TASK_SIZE) {
-+ return copy_from_user(dst, src, size);
-+ } else {
-+ memcpy(dst, src, size);
-+ return 0;
-+ }
-+}
-+
-+VCHIQ_STATUS_T
-+vchiq_prepare_bulk_data(VCHIQ_BULK_T *bulk, VCHI_MEM_HANDLE_T memhandle,
-+ void *offset, int size, int dir)
-+{
-+ PAGELIST_T *pagelist;
-+ int ret;
-+
-+ WARN_ON(memhandle != VCHI_MEM_HANDLE_INVALID);
-+
-+ ret = create_pagelist((char __user *)offset, size,
-+ (dir == VCHIQ_BULK_RECEIVE)
-+ ? PAGELIST_READ
-+ : PAGELIST_WRITE,
-+ current,
-+ &pagelist);
-+ if (ret != 0)
-+ return VCHIQ_ERROR;
-+
-+ bulk->handle = memhandle;
-+ bulk->data = VCHIQ_ARM_ADDRESS(pagelist);
-+
-+ /* Store the pagelist address in remote_data, which isn't used by the
-+ slave. */
-+ bulk->remote_data = pagelist;
-+
-+ return VCHIQ_SUCCESS;
-+}
-+
-+void
-+vchiq_complete_bulk(VCHIQ_BULK_T *bulk)
-+{
-+ if (bulk && bulk->remote_data && bulk->actual)
-+ free_pagelist((PAGELIST_T *)bulk->remote_data, bulk->actual);
-+}
-+
-+void
-+vchiq_transfer_bulk(VCHIQ_BULK_T *bulk)
-+{
-+ /*
-+ * This should only be called on the master (VideoCore) side, but
-+ * provide an implementation to avoid the need for ifdefery.
-+ */
-+ BUG();
-+}
-+
-+void
-+vchiq_dump_platform_state(void *dump_context)
-+{
-+ char buf[80];
-+ int len;
-+ len = snprintf(buf, sizeof(buf),
-+ " Platform: 2835 (VC master)");
-+ vchiq_dump(dump_context, buf, len + 1);
-+}
-+
-+VCHIQ_STATUS_T
-+vchiq_platform_suspend(VCHIQ_STATE_T *state)
-+{
-+ return VCHIQ_ERROR;
-+}
-+
-+VCHIQ_STATUS_T
-+vchiq_platform_resume(VCHIQ_STATE_T *state)
-+{
-+ return VCHIQ_SUCCESS;
-+}
-+
-+void
-+vchiq_platform_paused(VCHIQ_STATE_T *state)
-+{
-+}
-+
-+void
-+vchiq_platform_resumed(VCHIQ_STATE_T *state)
-+{
-+}
-+
-+int
-+vchiq_platform_videocore_wanted(VCHIQ_STATE_T* state)
-+{
-+ return 1; // autosuspend not supported - videocore always wanted
-+}
-+
-+int
-+vchiq_platform_use_suspend_timer(void)
-+{
-+ return 0;
-+}
-+void
-+vchiq_dump_platform_use_state(VCHIQ_STATE_T *state)
-+{
-+ vchiq_log_info(vchiq_arm_log_level, "Suspend timer not in use");
-+}
-+void
-+vchiq_platform_handle_timeout(VCHIQ_STATE_T *state)
-+{
-+ (void)state;
-+}
-+/*
-+ * Local functions
-+ */
-+
-+static irqreturn_t
-+vchiq_doorbell_irq(int irq, void *dev_id)
-+{
-+ VCHIQ_STATE_T *state = dev_id;
-+ irqreturn_t ret = IRQ_NONE;
-+ unsigned int status;
-+
-+ /* Read (and clear) the doorbell */
-+ status = readl(g_regs + BELL0);
-+
-+ if (status & 0x4) { /* Was the doorbell rung? */
-+ remote_event_pollall(state);
-+ ret = IRQ_HANDLED;
-+ }
-+
-+ return ret;
-+}
-+
-+/* There is a potential problem with partial cache lines (pages?)
-+** at the ends of the block when reading. If the CPU accessed anything in
-+** the same line (page?) then it may have pulled old data into the cache,
-+** obscuring the new data underneath. We can solve this by transferring the
-+** partial cache lines separately, and allowing the ARM to copy into the
-+** cached area.
-+
-+** N.B. This implementation plays slightly fast and loose with the Linux
-+** driver programming rules, e.g. its use of dmac_map_area instead of
-+** dma_map_single, but it isn't a multi-platform driver and it benefits
-+** from increased speed as a result.
-+*/
-+
-+static int
-+create_pagelist(char __user *buf, size_t count, unsigned short type,
-+ struct task_struct *task, PAGELIST_T ** ppagelist)
-+{
-+ PAGELIST_T *pagelist;
-+ struct page **pages;
-+ unsigned long *addrs;
-+ unsigned int num_pages, offset, i;
-+ char *addr, *base_addr, *next_addr;
-+ int run, addridx, actual_pages;
-+ unsigned long *need_release;
-+
-+ offset = (unsigned int)buf & (PAGE_SIZE - 1);
-+ num_pages = (count + offset + PAGE_SIZE - 1) / PAGE_SIZE;
-+
-+ *ppagelist = NULL;
-+
-+ /* Allocate enough storage to hold the page pointers and the page
-+ ** list
-+ */
-+ pagelist = kmalloc(sizeof(PAGELIST_T) +
-+ (num_pages * sizeof(unsigned long)) +
-+ sizeof(unsigned long) +
-+ (num_pages * sizeof(pages[0])),
-+ GFP_KERNEL);
-+
-+ vchiq_log_trace(vchiq_arm_log_level,
-+ "create_pagelist - %x", (unsigned int)pagelist);
-+ if (!pagelist)
-+ return -ENOMEM;
-+
-+ addrs = pagelist->addrs;
-+ need_release = (unsigned long *)(addrs + num_pages);
-+ pages = (struct page **)(addrs + num_pages + 1);
-+
-+ if (is_vmalloc_addr(buf)) {
-+ int dir = (type == PAGELIST_WRITE) ?
-+ DMA_TO_DEVICE : DMA_FROM_DEVICE;
-+ unsigned long length = count;
-+ unsigned int off = offset;
-+
-+ for (actual_pages = 0; actual_pages < num_pages;
-+ actual_pages++) {
-+ struct page *pg = vmalloc_to_page(buf + (actual_pages *
-+ PAGE_SIZE));
-+ size_t bytes = PAGE_SIZE - off;
-+
-+ if (bytes > length)
-+ bytes = length;
-+ pages[actual_pages] = pg;
-+ dmac_map_area(page_address(pg) + off, bytes, dir);
-+ length -= bytes;
-+ off = 0;
-+ }
-+ *need_release = 0; /* do not try and release vmalloc pages */
-+ } else {
-+ down_read(&task->mm->mmap_sem);
-+ actual_pages = get_user_pages(task, task->mm,
-+ (unsigned long)buf & ~(PAGE_SIZE - 1),
-+ num_pages,
-+ (type == PAGELIST_READ) /*Write */ ,
-+ 0 /*Force */ ,
-+ pages,
-+ NULL /*vmas */);
-+ up_read(&task->mm->mmap_sem);
-+
-+ if (actual_pages != num_pages) {
-+ vchiq_log_info(vchiq_arm_log_level,
-+ "create_pagelist - only %d/%d pages locked",
-+ actual_pages,
-+ num_pages);
-+
-+ /* This is probably due to the process being killed */
-+ while (actual_pages > 0)
-+ {
-+ actual_pages--;
-+ page_cache_release(pages[actual_pages]);
-+ }
-+ kfree(pagelist);
-+ if (actual_pages == 0)
-+ actual_pages = -ENOMEM;
-+ return actual_pages;
-+ }
-+ *need_release = 1; /* release user pages */
-+ }
-+
-+ pagelist->length = count;
-+ pagelist->type = type;
-+ pagelist->offset = offset;
-+
-+ /* Group the pages into runs of contiguous pages */
-+
-+ base_addr = VCHIQ_ARM_ADDRESS(page_address(pages[0]));
-+ next_addr = base_addr + PAGE_SIZE;
-+ addridx = 0;
-+ run = 0;
-+
-+ for (i = 1; i < num_pages; i++) {
-+ addr = VCHIQ_ARM_ADDRESS(page_address(pages[i]));
-+ if ((addr == next_addr) && (run < (PAGE_SIZE - 1))) {
-+ next_addr += PAGE_SIZE;
-+ run++;
-+ } else {
-+ addrs[addridx] = (unsigned long)base_addr + run;
-+ addridx++;
-+ base_addr = addr;
-+ next_addr = addr + PAGE_SIZE;
-+ run = 0;
-+ }
-+ }
-+
-+ addrs[addridx] = (unsigned long)base_addr + run;
-+ addridx++;
-+
-+ /* Partial cache lines (fragments) require special measures */
-+ if ((type == PAGELIST_READ) &&
-+ ((pagelist->offset & (g_cache_line_size - 1)) ||
-+ ((pagelist->offset + pagelist->length) &
-+ (g_cache_line_size - 1)))) {
-+ char *fragments;
-+
-+ if (down_interruptible(&g_free_fragments_sema) != 0) {
-+ kfree(pagelist);
-+ return -EINTR;
-+ }
-+
-+ WARN_ON(g_free_fragments == NULL);
-+
-+ down(&g_free_fragments_mutex);
-+ fragments = g_free_fragments;
-+ WARN_ON(fragments == NULL);
-+ g_free_fragments = *(char **) g_free_fragments;
-+ up(&g_free_fragments_mutex);
-+ pagelist->type = PAGELIST_READ_WITH_FRAGMENTS +
-+ (fragments - g_fragments_base) / g_fragments_size;
-+ }
-+
-+ dmac_flush_range(pagelist, addrs + num_pages);
-+
-+ *ppagelist = pagelist;
-+
-+ return 0;
-+}
-+
-+static void
-+free_pagelist(PAGELIST_T *pagelist, int actual)
-+{
-+ unsigned long *need_release;
-+ struct page **pages;
-+ unsigned int num_pages, i;
-+
-+ vchiq_log_trace(vchiq_arm_log_level,
-+ "free_pagelist - %x, %d", (unsigned int)pagelist, actual);
-+
-+ num_pages =
-+ (pagelist->length + pagelist->offset + PAGE_SIZE - 1) /
-+ PAGE_SIZE;
-+
-+ need_release = (unsigned long *)(pagelist->addrs + num_pages);
-+ pages = (struct page **)(pagelist->addrs + num_pages + 1);
-+
-+ /* Deal with any partial cache lines (fragments) */
-+ if (pagelist->type >= PAGELIST_READ_WITH_FRAGMENTS) {
-+ char *fragments = g_fragments_base +
-+ (pagelist->type - PAGELIST_READ_WITH_FRAGMENTS) *
-+ g_fragments_size;
-+ int head_bytes, tail_bytes;
-+ head_bytes = (g_cache_line_size - pagelist->offset) &
-+ (g_cache_line_size - 1);
-+ tail_bytes = (pagelist->offset + actual) &
-+ (g_cache_line_size - 1);
-+
-+ if ((actual >= 0) && (head_bytes != 0)) {
-+ if (head_bytes > actual)
-+ head_bytes = actual;
-+
-+ memcpy((char *)page_address(pages[0]) +
-+ pagelist->offset,
-+ fragments,
-+ head_bytes);
-+ }
-+ if ((actual >= 0) && (head_bytes < actual) &&
-+ (tail_bytes != 0)) {
-+ memcpy((char *)page_address(pages[num_pages - 1]) +
-+ ((pagelist->offset + actual) &
-+ (PAGE_SIZE - 1) & ~(g_cache_line_size - 1)),
-+ fragments + g_cache_line_size,
-+ tail_bytes);
-+ }
-+
-+ down(&g_free_fragments_mutex);
-+ *(char **)fragments = g_free_fragments;
-+ g_free_fragments = fragments;
-+ up(&g_free_fragments_mutex);
-+ up(&g_free_fragments_sema);
-+ }
-+
-+ if (*need_release) {
-+ unsigned int length = pagelist->length;
-+ unsigned int offset = pagelist->offset;
-+
-+ for (i = 0; i < num_pages; i++) {
-+ struct page *pg = pages[i];
-+
-+ if (pagelist->type != PAGELIST_WRITE) {
-+ unsigned int bytes = PAGE_SIZE - offset;
-+
-+ if (bytes > length)
-+ bytes = length;
-+ dmac_unmap_area(page_address(pg) + offset,
-+ bytes, DMA_FROM_DEVICE);
-+ length -= bytes;
-+ offset = 0;
-+ set_page_dirty(pg);
-+ }
-+ page_cache_release(pg);
-+ }
-+ }
-+
-+ kfree(pagelist);
-+}
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_arm.c
-@@ -0,0 +1,2903 @@
-+/**
-+ * Copyright (c) 2014 Raspberry Pi (Trading) Ltd. All rights reserved.
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+#include <linux/types.h>
-+#include <linux/errno.h>
-+#include <linux/cdev.h>
-+#include <linux/fs.h>
-+#include <linux/device.h>
-+#include <linux/mm.h>
-+#include <linux/highmem.h>
-+#include <linux/pagemap.h>
-+#include <linux/bug.h>
-+#include <linux/semaphore.h>
-+#include <linux/list.h>
-+#include <linux/of.h>
-+#include <linux/platform_device.h>
-+#include <soc/bcm2835/raspberrypi-firmware.h>
-+
-+#include "vchiq_core.h"
-+#include "vchiq_ioctl.h"
-+#include "vchiq_arm.h"
-+#include "vchiq_debugfs.h"
-+#include "vchiq_killable.h"
-+
-+#define DEVICE_NAME "vchiq"
-+
-+/* Override the default prefix, which would be vchiq_arm (from the filename) */
-+#undef MODULE_PARAM_PREFIX
-+#define MODULE_PARAM_PREFIX DEVICE_NAME "."
-+
-+#define VCHIQ_MINOR 0
-+
-+/* Some per-instance constants */
-+#define MAX_COMPLETIONS 16
-+#define MAX_SERVICES 64
-+#define MAX_ELEMENTS 8
-+#define MSG_QUEUE_SIZE 64
-+
-+#define KEEPALIVE_VER 1
-+#define KEEPALIVE_VER_MIN KEEPALIVE_VER
-+
-+/* Run time control of log level, based on KERN_XXX level. */
-+int vchiq_arm_log_level = VCHIQ_LOG_DEFAULT;
-+int vchiq_susp_log_level = VCHIQ_LOG_ERROR;
-+
-+#define SUSPEND_TIMER_TIMEOUT_MS 100
-+#define SUSPEND_RETRY_TIMER_TIMEOUT_MS 1000
-+
-+#define VC_SUSPEND_NUM_OFFSET 3 /* number of values before idle which are -ve */
-+static const char *const suspend_state_names[] = {
-+ "VC_SUSPEND_FORCE_CANCELED",
-+ "VC_SUSPEND_REJECTED",
-+ "VC_SUSPEND_FAILED",
-+ "VC_SUSPEND_IDLE",
-+ "VC_SUSPEND_REQUESTED",
-+ "VC_SUSPEND_IN_PROGRESS",
-+ "VC_SUSPEND_SUSPENDED"
-+};
-+#define VC_RESUME_NUM_OFFSET 1 /* number of values before idle which are -ve */
-+static const char *const resume_state_names[] = {
-+ "VC_RESUME_FAILED",
-+ "VC_RESUME_IDLE",
-+ "VC_RESUME_REQUESTED",
-+ "VC_RESUME_IN_PROGRESS",
-+ "VC_RESUME_RESUMED"
-+};
-+/* The number of times we allow force suspend to timeout before actually
-+** _forcing_ suspend. This is to cater for SW which fails to release vchiq
-+** correctly - we don't want to prevent ARM suspend indefinitely in this case.
-+*/
-+#define FORCE_SUSPEND_FAIL_MAX 8
-+
-+/* The time in ms allowed for videocore to go idle when force suspend has been
-+ * requested */
-+#define FORCE_SUSPEND_TIMEOUT_MS 200
-+
-+
-+static void suspend_timer_callback(unsigned long context);
-+
-+
-+typedef struct user_service_struct {
-+ VCHIQ_SERVICE_T *service;
-+ void *userdata;
-+ VCHIQ_INSTANCE_T instance;
-+ char is_vchi;
-+ char dequeue_pending;
-+ char close_pending;
-+ int message_available_pos;
-+ int msg_insert;
-+ int msg_remove;
-+ struct semaphore insert_event;
-+ struct semaphore remove_event;
-+ struct semaphore close_event;
-+ VCHIQ_HEADER_T * msg_queue[MSG_QUEUE_SIZE];
-+} USER_SERVICE_T;
-+
-+struct bulk_waiter_node {
-+ struct bulk_waiter bulk_waiter;
-+ int pid;
-+ struct list_head list;
-+};
-+
-+struct vchiq_instance_struct {
-+ VCHIQ_STATE_T *state;
-+ VCHIQ_COMPLETION_DATA_T completions[MAX_COMPLETIONS];
-+ int completion_insert;
-+ int completion_remove;
-+ struct semaphore insert_event;
-+ struct semaphore remove_event;
-+ struct mutex completion_mutex;
-+
-+ int connected;
-+ int closing;
-+ int pid;
-+ int mark;
-+ int use_close_delivered;
-+ int trace;
-+
-+ struct list_head bulk_waiter_list;
-+ struct mutex bulk_waiter_list_mutex;
-+
-+ VCHIQ_DEBUGFS_NODE_T debugfs_node;
-+};
-+
-+typedef struct dump_context_struct {
-+ char __user *buf;
-+ size_t actual;
-+ size_t space;
-+ loff_t offset;
-+} DUMP_CONTEXT_T;
-+
-+static struct cdev vchiq_cdev;
-+static dev_t vchiq_devid;
-+static VCHIQ_STATE_T g_state;
-+static struct class *vchiq_class;
-+static struct device *vchiq_dev;
-+static DEFINE_SPINLOCK(msg_queue_spinlock);
-+
-+static const char *const ioctl_names[] = {
-+ "CONNECT",
-+ "SHUTDOWN",
-+ "CREATE_SERVICE",
-+ "REMOVE_SERVICE",
-+ "QUEUE_MESSAGE",
-+ "QUEUE_BULK_TRANSMIT",
-+ "QUEUE_BULK_RECEIVE",
-+ "AWAIT_COMPLETION",
-+ "DEQUEUE_MESSAGE",
-+ "GET_CLIENT_ID",
-+ "GET_CONFIG",
-+ "CLOSE_SERVICE",
-+ "USE_SERVICE",
-+ "RELEASE_SERVICE",
-+ "SET_SERVICE_OPTION",
-+ "DUMP_PHYS_MEM",
-+ "LIB_VERSION",
-+ "CLOSE_DELIVERED"
-+};
-+
-+vchiq_static_assert((sizeof(ioctl_names)/sizeof(ioctl_names[0])) ==
-+ (VCHIQ_IOC_MAX + 1));
-+
-+static void
-+dump_phys_mem(void *virt_addr, uint32_t num_bytes);
-+
-+/****************************************************************************
-+*
-+* add_completion
-+*
-+***************************************************************************/
-+
-+static VCHIQ_STATUS_T
-+add_completion(VCHIQ_INSTANCE_T instance, VCHIQ_REASON_T reason,
-+ VCHIQ_HEADER_T *header, USER_SERVICE_T *user_service,
-+ void *bulk_userdata)
-+{
-+ VCHIQ_COMPLETION_DATA_T *completion;
-+ DEBUG_INITIALISE(g_state.local)
-+
-+ while (instance->completion_insert ==
-+ (instance->completion_remove + MAX_COMPLETIONS)) {
-+ /* Out of space - wait for the client */
-+ DEBUG_TRACE(SERVICE_CALLBACK_LINE);
-+ vchiq_log_trace(vchiq_arm_log_level,
-+ "add_completion - completion queue full");
-+ DEBUG_COUNT(COMPLETION_QUEUE_FULL_COUNT);
-+ if (down_interruptible(&instance->remove_event) != 0) {
-+ vchiq_log_info(vchiq_arm_log_level,
-+ "service_callback interrupted");
-+ return VCHIQ_RETRY;
-+ } else if (instance->closing) {
-+ vchiq_log_info(vchiq_arm_log_level,
-+ "service_callback closing");
-+ return VCHIQ_ERROR;
-+ }
-+ DEBUG_TRACE(SERVICE_CALLBACK_LINE);
-+ }
-+
-+ completion =
-+ &instance->completions[instance->completion_insert &
-+ (MAX_COMPLETIONS - 1)];
-+
-+ completion->header = header;
-+ completion->reason = reason;
-+ /* N.B. service_userdata is updated while processing AWAIT_COMPLETION */
-+ completion->service_userdata = user_service->service;
-+ completion->bulk_userdata = bulk_userdata;
-+
-+ if (reason == VCHIQ_SERVICE_CLOSED) {
-+ /* Take an extra reference, to be held until
-+ this CLOSED notification is delivered. */
-+ lock_service(user_service->service);
-+ if (instance->use_close_delivered)
-+ user_service->close_pending = 1;
-+ }
-+
-+ /* A write barrier is needed here to ensure that the entire completion
-+ record is written out before the insert point. */
-+ wmb();
-+
-+ if (reason == VCHIQ_MESSAGE_AVAILABLE)
-+ user_service->message_available_pos =
-+ instance->completion_insert;
-+ instance->completion_insert++;
-+
-+ up(&instance->insert_event);
-+
-+ return VCHIQ_SUCCESS;
-+}
-+
-+/****************************************************************************
-+*
-+* service_callback
-+*
-+***************************************************************************/
-+
-+static VCHIQ_STATUS_T
-+service_callback(VCHIQ_REASON_T reason, VCHIQ_HEADER_T *header,
-+ VCHIQ_SERVICE_HANDLE_T handle, void *bulk_userdata)
-+{
-+ /* How do we ensure the callback goes to the right client?
-+ ** The service_user data points to a USER_SERVICE_T record containing
-+ ** the original callback and the user state structure, which contains a
-+ ** circular buffer for completion records.
-+ */
-+ USER_SERVICE_T *user_service;
-+ VCHIQ_SERVICE_T *service;
-+ VCHIQ_INSTANCE_T instance;
-+ DEBUG_INITIALISE(g_state.local)
-+
-+ DEBUG_TRACE(SERVICE_CALLBACK_LINE);
-+
-+ service = handle_to_service(handle);
-+ BUG_ON(!service);
-+ user_service = (USER_SERVICE_T *)service->base.userdata;
-+ instance = user_service->instance;
-+
-+ if (!instance || instance->closing)
-+ return VCHIQ_SUCCESS;
-+
-+ vchiq_log_trace(vchiq_arm_log_level,
-+ "service_callback - service %lx(%d,%p), reason %d, header %lx, "
-+ "instance %lx, bulk_userdata %lx",
-+ (unsigned long)user_service,
-+ service->localport, user_service->userdata,
-+ reason, (unsigned long)header,
-+ (unsigned long)instance, (unsigned long)bulk_userdata);
-+
-+ if (header && user_service->is_vchi) {
-+ spin_lock(&msg_queue_spinlock);
-+ while (user_service->msg_insert ==
-+ (user_service->msg_remove + MSG_QUEUE_SIZE)) {
-+ spin_unlock(&msg_queue_spinlock);
-+ DEBUG_TRACE(SERVICE_CALLBACK_LINE);
-+ DEBUG_COUNT(MSG_QUEUE_FULL_COUNT);
-+ vchiq_log_trace(vchiq_arm_log_level,
-+ "service_callback - msg queue full");
-+ /* If there is no MESSAGE_AVAILABLE in the completion
-+ ** queue, add one
-+ */
-+ if ((user_service->message_available_pos -
-+ instance->completion_remove) < 0) {
-+ VCHIQ_STATUS_T status;
-+ vchiq_log_info(vchiq_arm_log_level,
-+ "Inserting extra MESSAGE_AVAILABLE");
-+ DEBUG_TRACE(SERVICE_CALLBACK_LINE);
-+ status = add_completion(instance, reason,
-+ NULL, user_service, bulk_userdata);
-+ if (status != VCHIQ_SUCCESS) {
-+ DEBUG_TRACE(SERVICE_CALLBACK_LINE);
-+ return status;
-+ }
-+ }
-+
-+ DEBUG_TRACE(SERVICE_CALLBACK_LINE);
-+ if (down_interruptible(&user_service->remove_event)
-+ != 0) {
-+ vchiq_log_info(vchiq_arm_log_level,
-+ "service_callback interrupted");
-+ DEBUG_TRACE(SERVICE_CALLBACK_LINE);
-+ return VCHIQ_RETRY;
-+ } else if (instance->closing) {
-+ vchiq_log_info(vchiq_arm_log_level,
-+ "service_callback closing");
-+ DEBUG_TRACE(SERVICE_CALLBACK_LINE);
-+ return VCHIQ_ERROR;
-+ }
-+ DEBUG_TRACE(SERVICE_CALLBACK_LINE);
-+ spin_lock(&msg_queue_spinlock);
-+ }
-+
-+ user_service->msg_queue[user_service->msg_insert &
-+ (MSG_QUEUE_SIZE - 1)] = header;
-+ user_service->msg_insert++;
-+ spin_unlock(&msg_queue_spinlock);
-+
-+ up(&user_service->insert_event);
-+
-+ /* If there is a thread waiting in DEQUEUE_MESSAGE, or if
-+ ** there is a MESSAGE_AVAILABLE in the completion queue then
-+ ** bypass the completion queue.
-+ */
-+ if (((user_service->message_available_pos -
-+ instance->completion_remove) >= 0) ||
-+ user_service->dequeue_pending) {
-+ DEBUG_TRACE(SERVICE_CALLBACK_LINE);
-+ user_service->dequeue_pending = 0;
-+ return VCHIQ_SUCCESS;
-+ }
-+
-+ header = NULL;
-+ }
-+ DEBUG_TRACE(SERVICE_CALLBACK_LINE);
-+
-+ return add_completion(instance, reason, header, user_service,
-+ bulk_userdata);
-+}
-+
-+/****************************************************************************
-+*
-+* user_service_free
-+*
-+***************************************************************************/
-+static void
-+user_service_free(void *userdata)
-+{
-+ kfree(userdata);
-+}
-+
-+/****************************************************************************
-+*
-+* close_delivered
-+*
-+***************************************************************************/
-+static void close_delivered(USER_SERVICE_T *user_service)
-+{
-+ vchiq_log_info(vchiq_arm_log_level,
-+ "close_delivered(handle=%x)",
-+ user_service->service->handle);
-+
-+ if (user_service->close_pending) {
-+ /* Allow the underlying service to be culled */
-+ unlock_service(user_service->service);
-+
-+ /* Wake the user-thread blocked in close_ or remove_service */
-+ up(&user_service->close_event);
-+
-+ user_service->close_pending = 0;
-+ }
-+}
-+
-+/****************************************************************************
-+*
-+* vchiq_ioctl
-+*
-+***************************************************************************/
-+static long
-+vchiq_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
-+{
-+ VCHIQ_INSTANCE_T instance = file->private_data;
-+ VCHIQ_STATUS_T status = VCHIQ_SUCCESS;
-+ VCHIQ_SERVICE_T *service = NULL;
-+ long ret = 0;
-+ int i, rc;
-+ DEBUG_INITIALISE(g_state.local)
-+
-+ vchiq_log_trace(vchiq_arm_log_level,
-+ "vchiq_ioctl - instance %x, cmd %s, arg %lx",
-+ (unsigned int)instance,
-+ ((_IOC_TYPE(cmd) == VCHIQ_IOC_MAGIC) &&
-+ (_IOC_NR(cmd) <= VCHIQ_IOC_MAX)) ?
-+ ioctl_names[_IOC_NR(cmd)] : "<invalid>", arg);
-+
-+ switch (cmd) {
-+ case VCHIQ_IOC_SHUTDOWN:
-+ if (!instance->connected)
-+ break;
-+
-+ /* Remove all services */
-+ i = 0;
-+ while ((service = next_service_by_instance(instance->state,
-+ instance, &i)) != NULL) {
-+ status = vchiq_remove_service(service->handle);
-+ unlock_service(service);
-+ if (status != VCHIQ_SUCCESS)
-+ break;
-+ }
-+ service = NULL;
-+
-+ if (status == VCHIQ_SUCCESS) {
-+ /* Wake the completion thread and ask it to exit */
-+ instance->closing = 1;
-+ up(&instance->insert_event);
-+ }
-+
-+ break;
-+
-+ case VCHIQ_IOC_CONNECT:
-+ if (instance->connected) {
-+ ret = -EINVAL;
-+ break;
-+ }
-+ rc = mutex_lock_interruptible(&instance->state->mutex);
-+ if (rc != 0) {
-+ vchiq_log_error(vchiq_arm_log_level,
-+ "vchiq: connect: could not lock mutex for "
-+ "state %d: %d",
-+ instance->state->id, rc);
-+ ret = -EINTR;
-+ break;
-+ }
-+ status = vchiq_connect_internal(instance->state, instance);
-+ mutex_unlock(&instance->state->mutex);
-+
-+ if (status == VCHIQ_SUCCESS)
-+ instance->connected = 1;
-+ else
-+ vchiq_log_error(vchiq_arm_log_level,
-+ "vchiq: could not connect: %d", status);
-+ break;
-+
-+ case VCHIQ_IOC_CREATE_SERVICE: {
-+ VCHIQ_CREATE_SERVICE_T args;
-+ USER_SERVICE_T *user_service = NULL;
-+ void *userdata;
-+ int srvstate;
-+
-+ if (copy_from_user
-+ (&args, (const void __user *)arg,
-+ sizeof(args)) != 0) {
-+ ret = -EFAULT;
-+ break;
-+ }
-+
-+ user_service = kmalloc(sizeof(USER_SERVICE_T), GFP_KERNEL);
-+ if (!user_service) {
-+ ret = -ENOMEM;
-+ break;
-+ }
-+
-+ if (args.is_open) {
-+ if (!instance->connected) {
-+ ret = -ENOTCONN;
-+ kfree(user_service);
-+ break;
-+ }
-+ srvstate = VCHIQ_SRVSTATE_OPENING;
-+ } else {
-+ srvstate =
-+ instance->connected ?
-+ VCHIQ_SRVSTATE_LISTENING :
-+ VCHIQ_SRVSTATE_HIDDEN;
-+ }
-+
-+ userdata = args.params.userdata;
-+ args.params.callback = service_callback;
-+ args.params.userdata = user_service;
-+ service = vchiq_add_service_internal(
-+ instance->state,
-+ &args.params, srvstate,
-+ instance, user_service_free);
-+
-+ if (service != NULL) {
-+ user_service->service = service;
-+ user_service->userdata = userdata;
-+ user_service->instance = instance;
-+ user_service->is_vchi = (args.is_vchi != 0);
-+ user_service->dequeue_pending = 0;
-+ user_service->close_pending = 0;
-+ user_service->message_available_pos =
-+ instance->completion_remove - 1;
-+ user_service->msg_insert = 0;
-+ user_service->msg_remove = 0;
-+ sema_init(&user_service->insert_event, 0);
-+ sema_init(&user_service->remove_event, 0);
-+ sema_init(&user_service->close_event, 0);
-+
-+ if (args.is_open) {
-+ status = vchiq_open_service_internal
-+ (service, instance->pid);
-+ if (status != VCHIQ_SUCCESS) {
-+ vchiq_remove_service(service->handle);
-+ service = NULL;
-+ ret = (status == VCHIQ_RETRY) ?
-+ -EINTR : -EIO;
-+ break;
-+ }
-+ }
-+
-+ if (copy_to_user((void __user *)
-+ &(((VCHIQ_CREATE_SERVICE_T __user *)
-+ arg)->handle),
-+ (const void *)&service->handle,
-+ sizeof(service->handle)) != 0) {
-+ ret = -EFAULT;
-+ vchiq_remove_service(service->handle);
-+ }
-+
-+ service = NULL;
-+ } else {
-+ ret = -EEXIST;
-+ kfree(user_service);
-+ }
-+ } break;
-+
-+ case VCHIQ_IOC_CLOSE_SERVICE: {
-+ VCHIQ_SERVICE_HANDLE_T handle = (VCHIQ_SERVICE_HANDLE_T)arg;
-+
-+ service = find_service_for_instance(instance, handle);
-+ if (service != NULL) {
-+ USER_SERVICE_T *user_service =
-+ (USER_SERVICE_T *)service->base.userdata;
-+ /* close_pending is false on first entry, and when the
-+ wait in vchiq_close_service has been interrupted. */
-+ if (!user_service->close_pending) {
-+ status = vchiq_close_service(service->handle);
-+ if (status != VCHIQ_SUCCESS)
-+ break;
-+ }
-+
-+ /* close_pending is true once the underlying service
-+ has been closed until the client library calls the
-+ CLOSE_DELIVERED ioctl, signalling close_event. */
-+ if (user_service->close_pending &&
-+ down_interruptible(&user_service->close_event))
-+ status = VCHIQ_RETRY;
-+ }
-+ else
-+ ret = -EINVAL;
-+ } break;
-+
-+ case VCHIQ_IOC_REMOVE_SERVICE: {
-+ VCHIQ_SERVICE_HANDLE_T handle = (VCHIQ_SERVICE_HANDLE_T)arg;
-+
-+ service = find_service_for_instance(instance, handle);
-+ if (service != NULL) {
-+ USER_SERVICE_T *user_service =
-+ (USER_SERVICE_T *)service->base.userdata;
-+ /* close_pending is false on first entry, and when the
-+ wait in vchiq_close_service has been interrupted. */
-+ if (!user_service->close_pending) {
-+ status = vchiq_remove_service(service->handle);
-+ if (status != VCHIQ_SUCCESS)
-+ break;
-+ }
-+
-+ /* close_pending is true once the underlying service
-+ has been closed until the client library calls the
-+ CLOSE_DELIVERED ioctl, signalling close_event. */
-+ if (user_service->close_pending &&
-+ down_interruptible(&user_service->close_event))
-+ status = VCHIQ_RETRY;
-+ }
-+ else
-+ ret = -EINVAL;
-+ } break;
-+
-+ case VCHIQ_IOC_USE_SERVICE:
-+ case VCHIQ_IOC_RELEASE_SERVICE: {
-+ VCHIQ_SERVICE_HANDLE_T handle = (VCHIQ_SERVICE_HANDLE_T)arg;
-+
-+ service = find_service_for_instance(instance, handle);
-+ if (service != NULL) {
-+ status = (cmd == VCHIQ_IOC_USE_SERVICE) ?
-+ vchiq_use_service_internal(service) :
-+ vchiq_release_service_internal(service);
-+ if (status != VCHIQ_SUCCESS) {
-+ vchiq_log_error(vchiq_susp_log_level,
-+ "%s: cmd %s returned error %d for "
-+ "service %c%c%c%c:%03d",
-+ __func__,
-+ (cmd == VCHIQ_IOC_USE_SERVICE) ?
-+ "VCHIQ_IOC_USE_SERVICE" :
-+ "VCHIQ_IOC_RELEASE_SERVICE",
-+ status,
-+ VCHIQ_FOURCC_AS_4CHARS(
-+ service->base.fourcc),
-+ service->client_id);
-+ ret = -EINVAL;
-+ }
-+ } else
-+ ret = -EINVAL;
-+ } break;
-+
-+ case VCHIQ_IOC_QUEUE_MESSAGE: {
-+ VCHIQ_QUEUE_MESSAGE_T args;
-+ if (copy_from_user
-+ (&args, (const void __user *)arg,
-+ sizeof(args)) != 0) {
-+ ret = -EFAULT;
-+ break;
-+ }
-+
-+ service = find_service_for_instance(instance, args.handle);
-+
-+ if ((service != NULL) && (args.count <= MAX_ELEMENTS)) {
-+ /* Copy elements into kernel space */
-+ VCHIQ_ELEMENT_T elements[MAX_ELEMENTS];
-+ if (copy_from_user(elements, args.elements,
-+ args.count * sizeof(VCHIQ_ELEMENT_T)) == 0)
-+ status = vchiq_queue_message
-+ (args.handle,
-+ elements, args.count);
-+ else
-+ ret = -EFAULT;
-+ } else {
-+ ret = -EINVAL;
-+ }
-+ } break;
-+
-+ case VCHIQ_IOC_QUEUE_BULK_TRANSMIT:
-+ case VCHIQ_IOC_QUEUE_BULK_RECEIVE: {
-+ VCHIQ_QUEUE_BULK_TRANSFER_T args;
-+ struct bulk_waiter_node *waiter = NULL;
-+ VCHIQ_BULK_DIR_T dir =
-+ (cmd == VCHIQ_IOC_QUEUE_BULK_TRANSMIT) ?
-+ VCHIQ_BULK_TRANSMIT : VCHIQ_BULK_RECEIVE;
-+
-+ if (copy_from_user
-+ (&args, (const void __user *)arg,
-+ sizeof(args)) != 0) {
-+ ret = -EFAULT;
-+ break;
-+ }
-+
-+ service = find_service_for_instance(instance, args.handle);
-+ if (!service) {
-+ ret = -EINVAL;
-+ break;
-+ }
-+
-+ if (args.mode == VCHIQ_BULK_MODE_BLOCKING) {
-+ waiter = kzalloc(sizeof(struct bulk_waiter_node),
-+ GFP_KERNEL);
-+ if (!waiter) {
-+ ret = -ENOMEM;
-+ break;
-+ }
-+ args.userdata = &waiter->bulk_waiter;
-+ } else if (args.mode == VCHIQ_BULK_MODE_WAITING) {
-+ struct list_head *pos;
-+ mutex_lock(&instance->bulk_waiter_list_mutex);
-+ list_for_each(pos, &instance->bulk_waiter_list) {
-+ if (list_entry(pos, struct bulk_waiter_node,
-+ list)->pid == current->pid) {
-+ waiter = list_entry(pos,
-+ struct bulk_waiter_node,
-+ list);
-+ list_del(pos);
-+ break;
-+ }
-+
-+ }
-+ mutex_unlock(&instance->bulk_waiter_list_mutex);
-+ if (!waiter) {
-+ vchiq_log_error(vchiq_arm_log_level,
-+ "no bulk_waiter found for pid %d",
-+ current->pid);
-+ ret = -ESRCH;
-+ break;
-+ }
-+ vchiq_log_info(vchiq_arm_log_level,
-+ "found bulk_waiter %x for pid %d",
-+ (unsigned int)waiter, current->pid);
-+ args.userdata = &waiter->bulk_waiter;
-+ }
-+ status = vchiq_bulk_transfer
-+ (args.handle,
-+ VCHI_MEM_HANDLE_INVALID,
-+ args.data, args.size,
-+ args.userdata, args.mode,
-+ dir);
-+ if (!waiter)
-+ break;
-+ if ((status != VCHIQ_RETRY) || fatal_signal_pending(current) ||
-+ !waiter->bulk_waiter.bulk) {
-+ if (waiter->bulk_waiter.bulk) {
-+ /* Cancel the signal when the transfer
-+ ** completes. */
-+ spin_lock(&bulk_waiter_spinlock);
-+ waiter->bulk_waiter.bulk->userdata = NULL;
-+ spin_unlock(&bulk_waiter_spinlock);
-+ }
-+ kfree(waiter);
-+ } else {
-+ const VCHIQ_BULK_MODE_T mode_waiting =
-+ VCHIQ_BULK_MODE_WAITING;
-+ waiter->pid = current->pid;
-+ mutex_lock(&instance->bulk_waiter_list_mutex);
-+ list_add(&waiter->list, &instance->bulk_waiter_list);
-+ mutex_unlock(&instance->bulk_waiter_list_mutex);
-+ vchiq_log_info(vchiq_arm_log_level,
-+ "saved bulk_waiter %x for pid %d",
-+ (unsigned int)waiter, current->pid);
-+
-+ if (copy_to_user((void __user *)
-+ &(((VCHIQ_QUEUE_BULK_TRANSFER_T __user *)
-+ arg)->mode),
-+ (const void *)&mode_waiting,
-+ sizeof(mode_waiting)) != 0)
-+ ret = -EFAULT;
-+ }
-+ } break;
-+
-+ case VCHIQ_IOC_AWAIT_COMPLETION: {
-+ VCHIQ_AWAIT_COMPLETION_T args;
-+
-+ DEBUG_TRACE(AWAIT_COMPLETION_LINE);
-+ if (!instance->connected) {
-+ ret = -ENOTCONN;
-+ break;
-+ }
-+
-+ if (copy_from_user(&args, (const void __user *)arg,
-+ sizeof(args)) != 0) {
-+ ret = -EFAULT;
-+ break;
-+ }
-+
-+ mutex_lock(&instance->completion_mutex);
-+
-+ DEBUG_TRACE(AWAIT_COMPLETION_LINE);
-+ while ((instance->completion_remove ==
-+ instance->completion_insert)
-+ && !instance->closing) {
-+ int rc;
-+ DEBUG_TRACE(AWAIT_COMPLETION_LINE);
-+ mutex_unlock(&instance->completion_mutex);
-+ rc = down_interruptible(&instance->insert_event);
-+ mutex_lock(&instance->completion_mutex);
-+ if (rc != 0) {
-+ DEBUG_TRACE(AWAIT_COMPLETION_LINE);
-+ vchiq_log_info(vchiq_arm_log_level,
-+ "AWAIT_COMPLETION interrupted");
-+ ret = -EINTR;
-+ break;
-+ }
-+ }
-+ DEBUG_TRACE(AWAIT_COMPLETION_LINE);
-+
-+ /* A read memory barrier is needed to stop prefetch of a stale
-+ ** completion record
-+ */
-+ rmb();
-+
-+ if (ret == 0) {
-+ int msgbufcount = args.msgbufcount;
-+ for (ret = 0; ret < args.count; ret++) {
-+ VCHIQ_COMPLETION_DATA_T *completion;
-+ VCHIQ_SERVICE_T *service;
-+ USER_SERVICE_T *user_service;
-+ VCHIQ_HEADER_T *header;
-+ if (instance->completion_remove ==
-+ instance->completion_insert)
-+ break;
-+ completion = &instance->completions[
-+ instance->completion_remove &
-+ (MAX_COMPLETIONS - 1)];
-+
-+ service = completion->service_userdata;
-+ user_service = service->base.userdata;
-+ completion->service_userdata =
-+ user_service->userdata;
-+
-+ header = completion->header;
-+ if (header) {
-+ void __user *msgbuf;
-+ int msglen;
-+
-+ msglen = header->size +
-+ sizeof(VCHIQ_HEADER_T);
-+ /* This must be a VCHIQ-style service */
-+ if (args.msgbufsize < msglen) {
-+ vchiq_log_error(
-+ vchiq_arm_log_level,
-+ "header %x: msgbufsize"
-+ " %x < msglen %x",
-+ (unsigned int)header,
-+ args.msgbufsize,
-+ msglen);
-+ WARN(1, "invalid message "
-+ "size\n");
-+ if (ret == 0)
-+ ret = -EMSGSIZE;
-+ break;
-+ }
-+ if (msgbufcount <= 0)
-+ /* Stall here for lack of a
-+ ** buffer for the message. */
-+ break;
-+ /* Get the pointer from user space */
-+ msgbufcount--;
-+ if (copy_from_user(&msgbuf,
-+ (const void __user *)
-+ &args.msgbufs[msgbufcount],
-+ sizeof(msgbuf)) != 0) {
-+ if (ret == 0)
-+ ret = -EFAULT;
-+ break;
-+ }
-+
-+ /* Copy the message to user space */
-+ if (copy_to_user(msgbuf, header,
-+ msglen) != 0) {
-+ if (ret == 0)
-+ ret = -EFAULT;
-+ break;
-+ }
-+
-+ /* Now it has been copied, the message
-+ ** can be released. */
-+ vchiq_release_message(service->handle,
-+ header);
-+
-+ /* The completion must point to the
-+ ** msgbuf. */
-+ completion->header = msgbuf;
-+ }
-+
-+ if ((completion->reason ==
-+ VCHIQ_SERVICE_CLOSED) &&
-+ !instance->use_close_delivered)
-+ unlock_service(service);
-+
-+ if (copy_to_user((void __user *)(
-+ (size_t)args.buf +
-+ ret * sizeof(VCHIQ_COMPLETION_DATA_T)),
-+ completion,
-+ sizeof(VCHIQ_COMPLETION_DATA_T)) != 0) {
-+ if (ret == 0)
-+ ret = -EFAULT;
-+ break;
-+ }
-+
-+ instance->completion_remove++;
-+ }
-+
-+ if (msgbufcount != args.msgbufcount) {
-+ if (copy_to_user((void __user *)
-+ &((VCHIQ_AWAIT_COMPLETION_T *)arg)->
-+ msgbufcount,
-+ &msgbufcount,
-+ sizeof(msgbufcount)) != 0) {
-+ ret = -EFAULT;
-+ }
-+ }
-+ }
-+
-+ if (ret != 0)
-+ up(&instance->remove_event);
-+ mutex_unlock(&instance->completion_mutex);
-+ DEBUG_TRACE(AWAIT_COMPLETION_LINE);
-+ } break;
-+
-+ case VCHIQ_IOC_DEQUEUE_MESSAGE: {
-+ VCHIQ_DEQUEUE_MESSAGE_T args;
-+ USER_SERVICE_T *user_service;
-+ VCHIQ_HEADER_T *header;
-+
-+ DEBUG_TRACE(DEQUEUE_MESSAGE_LINE);
-+ if (copy_from_user
-+ (&args, (const void __user *)arg,
-+ sizeof(args)) != 0) {
-+ ret = -EFAULT;
-+ break;
-+ }
-+ service = find_service_for_instance(instance, args.handle);
-+ if (!service) {
-+ ret = -EINVAL;
-+ break;
-+ }
-+ user_service = (USER_SERVICE_T *)service->base.userdata;
-+ if (user_service->is_vchi == 0) {
-+ ret = -EINVAL;
-+ break;
-+ }
-+
-+ spin_lock(&msg_queue_spinlock);
-+ if (user_service->msg_remove == user_service->msg_insert) {
-+ if (!args.blocking) {
-+ spin_unlock(&msg_queue_spinlock);
-+ DEBUG_TRACE(DEQUEUE_MESSAGE_LINE);
-+ ret = -EWOULDBLOCK;
-+ break;
-+ }
-+ user_service->dequeue_pending = 1;
-+ do {
-+ spin_unlock(&msg_queue_spinlock);
-+ DEBUG_TRACE(DEQUEUE_MESSAGE_LINE);
-+ if (down_interruptible(
-+ &user_service->insert_event) != 0) {
-+ vchiq_log_info(vchiq_arm_log_level,
-+ "DEQUEUE_MESSAGE interrupted");
-+ ret = -EINTR;
-+ break;
-+ }
-+ spin_lock(&msg_queue_spinlock);
-+ } while (user_service->msg_remove ==
-+ user_service->msg_insert);
-+
-+ if (ret)
-+ break;
-+ }
-+
-+ BUG_ON((int)(user_service->msg_insert -
-+ user_service->msg_remove) < 0);
-+
-+ header = user_service->msg_queue[user_service->msg_remove &
-+ (MSG_QUEUE_SIZE - 1)];
-+ user_service->msg_remove++;
-+ spin_unlock(&msg_queue_spinlock);
-+
-+ up(&user_service->remove_event);
-+ if (header == NULL)
-+ ret = -ENOTCONN;
-+ else if (header->size <= args.bufsize) {
-+ /* Copy to user space if msgbuf is not NULL */
-+ if ((args.buf == NULL) ||
-+ (copy_to_user((void __user *)args.buf,
-+ header->data,
-+ header->size) == 0)) {
-+ ret = header->size;
-+ vchiq_release_message(
-+ service->handle,
-+ header);
-+ } else
-+ ret = -EFAULT;
-+ } else {
-+ vchiq_log_error(vchiq_arm_log_level,
-+ "header %x: bufsize %x < size %x",
-+ (unsigned int)header, args.bufsize,
-+ header->size);
-+ WARN(1, "invalid size\n");
-+ ret = -EMSGSIZE;
-+ }
-+ DEBUG_TRACE(DEQUEUE_MESSAGE_LINE);
-+ } break;
-+
-+ case VCHIQ_IOC_GET_CLIENT_ID: {
-+ VCHIQ_SERVICE_HANDLE_T handle = (VCHIQ_SERVICE_HANDLE_T)arg;
-+
-+ ret = vchiq_get_client_id(handle);
-+ } break;
-+
-+ case VCHIQ_IOC_GET_CONFIG: {
-+ VCHIQ_GET_CONFIG_T args;
-+ VCHIQ_CONFIG_T config;
-+
-+ if (copy_from_user(&args, (const void __user *)arg,
-+ sizeof(args)) != 0) {
-+ ret = -EFAULT;
-+ break;
-+ }
-+ if (args.config_size > sizeof(config)) {
-+ ret = -EINVAL;
-+ break;
-+ }
-+ status = vchiq_get_config(instance, args.config_size, &config);
-+ if (status == VCHIQ_SUCCESS) {
-+ if (copy_to_user((void __user *)args.pconfig,
-+ &config, args.config_size) != 0) {
-+ ret = -EFAULT;
-+ break;
-+ }
-+ }
-+ } break;
-+
-+ case VCHIQ_IOC_SET_SERVICE_OPTION: {
-+ VCHIQ_SET_SERVICE_OPTION_T args;
-+
-+ if (copy_from_user(
-+ &args, (const void __user *)arg,
-+ sizeof(args)) != 0) {
-+ ret = -EFAULT;
-+ break;
-+ }
-+
-+ service = find_service_for_instance(instance, args.handle);
-+ if (!service) {
-+ ret = -EINVAL;
-+ break;
-+ }
-+
-+ status = vchiq_set_service_option(
-+ args.handle, args.option, args.value);
-+ } break;
-+
-+ case VCHIQ_IOC_DUMP_PHYS_MEM: {
-+ VCHIQ_DUMP_MEM_T args;
-+
-+ if (copy_from_user
-+ (&args, (const void __user *)arg,
-+ sizeof(args)) != 0) {
-+ ret = -EFAULT;
-+ break;
-+ }
-+ dump_phys_mem(args.virt_addr, args.num_bytes);
-+ } break;
-+
-+ case VCHIQ_IOC_LIB_VERSION: {
-+ unsigned int lib_version = (unsigned int)arg;
-+
-+ if (lib_version < VCHIQ_VERSION_MIN)
-+ ret = -EINVAL;
-+ else if (lib_version >= VCHIQ_VERSION_CLOSE_DELIVERED)
-+ instance->use_close_delivered = 1;
-+ } break;
-+
-+ case VCHIQ_IOC_CLOSE_DELIVERED: {
-+ VCHIQ_SERVICE_HANDLE_T handle = (VCHIQ_SERVICE_HANDLE_T)arg;
-+
-+ service = find_closed_service_for_instance(instance, handle);
-+ if (service != NULL) {
-+ USER_SERVICE_T *user_service =
-+ (USER_SERVICE_T *)service->base.userdata;
-+ close_delivered(user_service);
-+ }
-+ else
-+ ret = -EINVAL;
-+ } break;
-+
-+ default:
-+ ret = -ENOTTY;
-+ break;
-+ }
-+
-+ if (service)
-+ unlock_service(service);
-+
-+ if (ret == 0) {
-+ if (status == VCHIQ_ERROR)
-+ ret = -EIO;
-+ else if (status == VCHIQ_RETRY)
-+ ret = -EINTR;
-+ }
-+
-+ if ((status == VCHIQ_SUCCESS) && (ret < 0) && (ret != -EINTR) &&
-+ (ret != -EWOULDBLOCK))
-+ vchiq_log_info(vchiq_arm_log_level,
-+ " ioctl instance %lx, cmd %s -> status %d, %ld",
-+ (unsigned long)instance,
-+ (_IOC_NR(cmd) <= VCHIQ_IOC_MAX) ?
-+ ioctl_names[_IOC_NR(cmd)] :
-+ "<invalid>",
-+ status, ret);
-+ else
-+ vchiq_log_trace(vchiq_arm_log_level,
-+ " ioctl instance %lx, cmd %s -> status %d, %ld",
-+ (unsigned long)instance,
-+ (_IOC_NR(cmd) <= VCHIQ_IOC_MAX) ?
-+ ioctl_names[_IOC_NR(cmd)] :
-+ "<invalid>",
-+ status, ret);
-+
-+ return ret;
-+}
-+
-+/****************************************************************************
-+*
-+* vchiq_open
-+*
-+***************************************************************************/
-+
-+static int
-+vchiq_open(struct inode *inode, struct file *file)
-+{
-+ int dev = iminor(inode) & 0x0f;
-+ vchiq_log_info(vchiq_arm_log_level, "vchiq_open");
-+ switch (dev) {
-+ case VCHIQ_MINOR: {
-+ int ret;
-+ VCHIQ_STATE_T *state = vchiq_get_state();
-+ VCHIQ_INSTANCE_T instance;
-+
-+ if (!state) {
-+ vchiq_log_error(vchiq_arm_log_level,
-+ "vchiq has no connection to VideoCore");
-+ return -ENOTCONN;
-+ }
-+
-+ instance = kzalloc(sizeof(*instance), GFP_KERNEL);
-+ if (!instance)
-+ return -ENOMEM;
-+
-+ instance->state = state;
-+ instance->pid = current->tgid;
-+
-+ ret = vchiq_debugfs_add_instance(instance);
-+ if (ret != 0) {
-+ kfree(instance);
-+ return ret;
-+ }
-+
-+ sema_init(&instance->insert_event, 0);
-+ sema_init(&instance->remove_event, 0);
-+ mutex_init(&instance->completion_mutex);
-+ mutex_init(&instance->bulk_waiter_list_mutex);
-+ INIT_LIST_HEAD(&instance->bulk_waiter_list);
-+
-+ file->private_data = instance;
-+ } break;
-+
-+ default:
-+ vchiq_log_error(vchiq_arm_log_level,
-+ "Unknown minor device: %d", dev);
-+ return -ENXIO;
-+ }
-+
-+ return 0;
-+}
-+
-+/****************************************************************************
-+*
-+* vchiq_release
-+*
-+***************************************************************************/
-+
-+static int
-+vchiq_release(struct inode *inode, struct file *file)
-+{
-+ int dev = iminor(inode) & 0x0f;
-+ int ret = 0;
-+ switch (dev) {
-+ case VCHIQ_MINOR: {
-+ VCHIQ_INSTANCE_T instance = file->private_data;
-+ VCHIQ_STATE_T *state = vchiq_get_state();
-+ VCHIQ_SERVICE_T *service;
-+ int i;
-+
-+ vchiq_log_info(vchiq_arm_log_level,
-+ "vchiq_release: instance=%lx",
-+ (unsigned long)instance);
-+
-+ if (!state) {
-+ ret = -EPERM;
-+ goto out;
-+ }
-+
-+ /* Ensure videocore is awake to allow termination. */
-+ vchiq_use_internal(instance->state, NULL,
-+ USE_TYPE_VCHIQ);
-+
-+ mutex_lock(&instance->completion_mutex);
-+
-+ /* Wake the completion thread and ask it to exit */
-+ instance->closing = 1;
-+ up(&instance->insert_event);
-+
-+ mutex_unlock(&instance->completion_mutex);
-+
-+ /* Wake the slot handler if the completion queue is full. */
-+ up(&instance->remove_event);
-+
-+ /* Mark all services for termination... */
-+ i = 0;
-+ while ((service = next_service_by_instance(state, instance,
-+ &i)) != NULL) {
-+ USER_SERVICE_T *user_service = service->base.userdata;
-+
-+ /* Wake the slot handler if the msg queue is full. */
-+ up(&user_service->remove_event);
-+
-+ vchiq_terminate_service_internal(service);
-+ unlock_service(service);
-+ }
-+
-+ /* ...and wait for them to die */
-+ i = 0;
-+ while ((service = next_service_by_instance(state, instance, &i))
-+ != NULL) {
-+ USER_SERVICE_T *user_service = service->base.userdata;
-+
-+ down(&service->remove_event);
-+
-+ BUG_ON(service->srvstate != VCHIQ_SRVSTATE_FREE);
-+
-+ spin_lock(&msg_queue_spinlock);
-+
-+ while (user_service->msg_remove !=
-+ user_service->msg_insert) {
-+ VCHIQ_HEADER_T *header = user_service->
-+ msg_queue[user_service->msg_remove &
-+ (MSG_QUEUE_SIZE - 1)];
-+ user_service->msg_remove++;
-+ spin_unlock(&msg_queue_spinlock);
-+
-+ if (header)
-+ vchiq_release_message(
-+ service->handle,
-+ header);
-+ spin_lock(&msg_queue_spinlock);
-+ }
-+
-+ spin_unlock(&msg_queue_spinlock);
-+
-+ unlock_service(service);
-+ }
-+
-+ /* Release any closed services */
-+ while (instance->completion_remove !=
-+ instance->completion_insert) {
-+ VCHIQ_COMPLETION_DATA_T *completion;
-+ VCHIQ_SERVICE_T *service;
-+ completion = &instance->completions[
-+ instance->completion_remove &
-+ (MAX_COMPLETIONS - 1)];
-+ service = completion->service_userdata;
-+ if (completion->reason == VCHIQ_SERVICE_CLOSED)
-+ {
-+ USER_SERVICE_T *user_service =
-+ service->base.userdata;
-+
-+ /* Wake any blocked user-thread */
-+ if (instance->use_close_delivered)
-+ up(&user_service->close_event);
-+ unlock_service(service);
-+ }
-+ instance->completion_remove++;
-+ }
-+
-+ /* Release the PEER service count. */
-+ vchiq_release_internal(instance->state, NULL);
-+
-+ {
-+ struct list_head *pos, *next;
-+ list_for_each_safe(pos, next,
-+ &instance->bulk_waiter_list) {
-+ struct bulk_waiter_node *waiter;
-+ waiter = list_entry(pos,
-+ struct bulk_waiter_node,
-+ list);
-+ list_del(pos);
-+ vchiq_log_info(vchiq_arm_log_level,
-+ "bulk_waiter - cleaned up %x "
-+ "for pid %d",
-+ (unsigned int)waiter, waiter->pid);
-+ kfree(waiter);
-+ }
-+ }
-+
-+ vchiq_debugfs_remove_instance(instance);
-+
-+ kfree(instance);
-+ file->private_data = NULL;
-+ } break;
-+
-+ default:
-+ vchiq_log_error(vchiq_arm_log_level,
-+ "Unknown minor device: %d", dev);
-+ ret = -ENXIO;
-+ }
-+
-+out:
-+ return ret;
-+}
-+
-+/****************************************************************************
-+*
-+* vchiq_dump
-+*
-+***************************************************************************/
-+
-+void
-+vchiq_dump(void *dump_context, const char *str, int len)
-+{
-+ DUMP_CONTEXT_T *context = (DUMP_CONTEXT_T *)dump_context;
-+
-+ if (context->actual < context->space) {
-+ int copy_bytes;
-+ if (context->offset > 0) {
-+ int skip_bytes = min(len, (int)context->offset);
-+ str += skip_bytes;
-+ len -= skip_bytes;
-+ context->offset -= skip_bytes;
-+ if (context->offset > 0)
-+ return;
-+ }
-+ copy_bytes = min(len, (int)(context->space - context->actual));
-+ if (copy_bytes == 0)
-+ return;
-+ if (copy_to_user(context->buf + context->actual, str,
-+ copy_bytes))
-+ context->actual = -EFAULT;
-+ context->actual += copy_bytes;
-+ len -= copy_bytes;
-+
-+ /* If tne terminating NUL is included in the length, then it
-+ ** marks the end of a line and should be replaced with a
-+ ** carriage return. */
-+ if ((len == 0) && (str[copy_bytes - 1] == '\0')) {
-+ char cr = '\n';
-+ if (copy_to_user(context->buf + context->actual - 1,
-+ &cr, 1))
-+ context->actual = -EFAULT;
-+ }
-+ }
-+}
-+
-+/****************************************************************************
-+*
-+* vchiq_dump_platform_instance_state
-+*
-+***************************************************************************/
-+
-+void
-+vchiq_dump_platform_instances(void *dump_context)
-+{
-+ VCHIQ_STATE_T *state = vchiq_get_state();
-+ char buf[80];
-+ int len;
-+ int i;
-+
-+ /* There is no list of instances, so instead scan all services,
-+ marking those that have been dumped. */
-+
-+ for (i = 0; i < state->unused_service; i++) {
-+ VCHIQ_SERVICE_T *service = state->services[i];
-+ VCHIQ_INSTANCE_T instance;
-+
-+ if (service && (service->base.callback == service_callback)) {
-+ instance = service->instance;
-+ if (instance)
-+ instance->mark = 0;
-+ }
-+ }
-+
-+ for (i = 0; i < state->unused_service; i++) {
-+ VCHIQ_SERVICE_T *service = state->services[i];
-+ VCHIQ_INSTANCE_T instance;
-+
-+ if (service && (service->base.callback == service_callback)) {
-+ instance = service->instance;
-+ if (instance && !instance->mark) {
-+ len = snprintf(buf, sizeof(buf),
-+ "Instance %x: pid %d,%s completions "
-+ "%d/%d",
-+ (unsigned int)instance, instance->pid,
-+ instance->connected ? " connected, " :
-+ "",
-+ instance->completion_insert -
-+ instance->completion_remove,
-+ MAX_COMPLETIONS);
-+
-+ vchiq_dump(dump_context, buf, len + 1);
-+
-+ instance->mark = 1;
-+ }
-+ }
-+ }
-+}
-+
-+/****************************************************************************
-+*
-+* vchiq_dump_platform_service_state
-+*
-+***************************************************************************/
-+
-+void
-+vchiq_dump_platform_service_state(void *dump_context, VCHIQ_SERVICE_T *service)
-+{
-+ USER_SERVICE_T *user_service = (USER_SERVICE_T *)service->base.userdata;
-+ char buf[80];
-+ int len;
-+
-+ len = snprintf(buf, sizeof(buf), " instance %x",
-+ (unsigned int)service->instance);
-+
-+ if ((service->base.callback == service_callback) &&
-+ user_service->is_vchi) {
-+ len += snprintf(buf + len, sizeof(buf) - len,
-+ ", %d/%d messages",
-+ user_service->msg_insert - user_service->msg_remove,
-+ MSG_QUEUE_SIZE);
-+
-+ if (user_service->dequeue_pending)
-+ len += snprintf(buf + len, sizeof(buf) - len,
-+ " (dequeue pending)");
-+ }
-+
-+ vchiq_dump(dump_context, buf, len + 1);
-+}
-+
-+/****************************************************************************
-+*
-+* dump_user_mem
-+*
-+***************************************************************************/
-+
-+static void
-+dump_phys_mem(void *virt_addr, uint32_t num_bytes)
-+{
-+ int rc;
-+ uint8_t *end_virt_addr = virt_addr + num_bytes;
-+ int num_pages;
-+ int offset;
-+ int end_offset;
-+ int page_idx;
-+ int prev_idx;
-+ struct page *page;
-+ struct page **pages;
-+ uint8_t *kmapped_virt_ptr;
-+
-+ /* Align virtAddr and endVirtAddr to 16 byte boundaries. */
-+
-+ virt_addr = (void *)((unsigned long)virt_addr & ~0x0fuL);
-+ end_virt_addr = (void *)(((unsigned long)end_virt_addr + 15uL) &
-+ ~0x0fuL);
-+
-+ offset = (int)(long)virt_addr & (PAGE_SIZE - 1);
-+ end_offset = (int)(long)end_virt_addr & (PAGE_SIZE - 1);
-+
-+ num_pages = (offset + num_bytes + PAGE_SIZE - 1) / PAGE_SIZE;
-+
-+ pages = kmalloc(sizeof(struct page *) * num_pages, GFP_KERNEL);
-+ if (pages == NULL) {
-+ vchiq_log_error(vchiq_arm_log_level,
-+ "Unable to allocation memory for %d pages\n",
-+ num_pages);
-+ return;
-+ }
-+
-+ down_read(¤t->mm->mmap_sem);
-+ rc = get_user_pages(current, /* task */
-+ current->mm, /* mm */
-+ (unsigned long)virt_addr, /* start */
-+ num_pages, /* len */
-+ 0, /* write */
-+ 0, /* force */
-+ pages, /* pages (array of page pointers) */
-+ NULL); /* vmas */
-+ up_read(¤t->mm->mmap_sem);
-+
-+ prev_idx = -1;
-+ page = NULL;
-+
-+ while (offset < end_offset) {
-+
-+ int page_offset = offset % PAGE_SIZE;
-+ page_idx = offset / PAGE_SIZE;
-+
-+ if (page_idx != prev_idx) {
-+
-+ if (page != NULL)
-+ kunmap(page);
-+ page = pages[page_idx];
-+ kmapped_virt_ptr = kmap(page);
-+
-+ prev_idx = page_idx;
-+ }
-+
-+ if (vchiq_arm_log_level >= VCHIQ_LOG_TRACE)
-+ vchiq_log_dump_mem("ph",
-+ (uint32_t)(unsigned long)&kmapped_virt_ptr[
-+ page_offset],
-+ &kmapped_virt_ptr[page_offset], 16);
-+
-+ offset += 16;
-+ }
-+ if (page != NULL)
-+ kunmap(page);
-+
-+ for (page_idx = 0; page_idx < num_pages; page_idx++)
-+ page_cache_release(pages[page_idx]);
-+
-+ kfree(pages);
-+}
-+
-+/****************************************************************************
-+*
-+* vchiq_read
-+*
-+***************************************************************************/
-+
-+static ssize_t
-+vchiq_read(struct file *file, char __user *buf,
-+ size_t count, loff_t *ppos)
-+{
-+ DUMP_CONTEXT_T context;
-+ context.buf = buf;
-+ context.actual = 0;
-+ context.space = count;
-+ context.offset = *ppos;
-+
-+ vchiq_dump_state(&context, &g_state);
-+
-+ *ppos += context.actual;
-+
-+ return context.actual;
-+}
-+
-+VCHIQ_STATE_T *
-+vchiq_get_state(void)
-+{
-+
-+ if (g_state.remote == NULL)
-+ printk(KERN_ERR "%s: g_state.remote == NULL\n", __func__);
-+ else if (g_state.remote->initialised != 1)
-+ printk(KERN_NOTICE "%s: g_state.remote->initialised != 1 (%d)\n",
-+ __func__, g_state.remote->initialised);
-+
-+ return ((g_state.remote != NULL) &&
-+ (g_state.remote->initialised == 1)) ? &g_state : NULL;
-+}
-+
-+static const struct file_operations
-+vchiq_fops = {
-+ .owner = THIS_MODULE,
-+ .unlocked_ioctl = vchiq_ioctl,
-+ .open = vchiq_open,
-+ .release = vchiq_release,
-+ .read = vchiq_read
-+};
-+
-+/*
-+ * Autosuspend related functionality
-+ */
-+
-+int
-+vchiq_videocore_wanted(VCHIQ_STATE_T *state)
-+{
-+ VCHIQ_ARM_STATE_T *arm_state = vchiq_platform_get_arm_state(state);
-+ if (!arm_state)
-+ /* autosuspend not supported - always return wanted */
-+ return 1;
-+ else if (arm_state->blocked_count)
-+ return 1;
-+ else if (!arm_state->videocore_use_count)
-+ /* usage count zero - check for override unless we're forcing */
-+ if (arm_state->resume_blocked)
-+ return 0;
-+ else
-+ return vchiq_platform_videocore_wanted(state);
-+ else
-+ /* non-zero usage count - videocore still required */
-+ return 1;
-+}
-+
-+static VCHIQ_STATUS_T
-+vchiq_keepalive_vchiq_callback(VCHIQ_REASON_T reason,
-+ VCHIQ_HEADER_T *header,
-+ VCHIQ_SERVICE_HANDLE_T service_user,
-+ void *bulk_user)
-+{
-+ vchiq_log_error(vchiq_susp_log_level,
-+ "%s callback reason %d", __func__, reason);
-+ return 0;
-+}
-+
-+static int
-+vchiq_keepalive_thread_func(void *v)
-+{
-+ VCHIQ_STATE_T *state = (VCHIQ_STATE_T *) v;
-+ VCHIQ_ARM_STATE_T *arm_state = vchiq_platform_get_arm_state(state);
-+
-+ VCHIQ_STATUS_T status;
-+ VCHIQ_INSTANCE_T instance;
-+ VCHIQ_SERVICE_HANDLE_T ka_handle;
-+
-+ VCHIQ_SERVICE_PARAMS_T params = {
-+ .fourcc = VCHIQ_MAKE_FOURCC('K', 'E', 'E', 'P'),
-+ .callback = vchiq_keepalive_vchiq_callback,
-+ .version = KEEPALIVE_VER,
-+ .version_min = KEEPALIVE_VER_MIN
-+ };
-+
-+ status = vchiq_initialise(&instance);
-+ if (status != VCHIQ_SUCCESS) {
-+ vchiq_log_error(vchiq_susp_log_level,
-+ "%s vchiq_initialise failed %d", __func__, status);
-+ goto exit;
-+ }
-+
-+ status = vchiq_connect(instance);
-+ if (status != VCHIQ_SUCCESS) {
-+ vchiq_log_error(vchiq_susp_log_level,
-+ "%s vchiq_connect failed %d", __func__, status);
-+ goto shutdown;
-+ }
-+
-+ status = vchiq_add_service(instance, ¶ms, &ka_handle);
-+ if (status != VCHIQ_SUCCESS) {
-+ vchiq_log_error(vchiq_susp_log_level,
-+ "%s vchiq_open_service failed %d", __func__, status);
-+ goto shutdown;
-+ }
-+
-+ while (1) {
-+ long rc = 0, uc = 0;
-+ if (wait_for_completion_interruptible(&arm_state->ka_evt)
-+ != 0) {
-+ vchiq_log_error(vchiq_susp_log_level,
-+ "%s interrupted", __func__);
-+ flush_signals(current);
-+ continue;
-+ }
-+
-+ /* read and clear counters. Do release_count then use_count to
-+ * prevent getting more releases than uses */
-+ rc = atomic_xchg(&arm_state->ka_release_count, 0);
-+ uc = atomic_xchg(&arm_state->ka_use_count, 0);
-+
-+ /* Call use/release service the requisite number of times.
-+ * Process use before release so use counts don't go negative */
-+ while (uc--) {
-+ atomic_inc(&arm_state->ka_use_ack_count);
-+ status = vchiq_use_service(ka_handle);
-+ if (status != VCHIQ_SUCCESS) {
-+ vchiq_log_error(vchiq_susp_log_level,
-+ "%s vchiq_use_service error %d",
-+ __func__, status);
-+ }
-+ }
-+ while (rc--) {
-+ status = vchiq_release_service(ka_handle);
-+ if (status != VCHIQ_SUCCESS) {
-+ vchiq_log_error(vchiq_susp_log_level,
-+ "%s vchiq_release_service error %d",
-+ __func__, status);
-+ }
-+ }
-+ }
-+
-+shutdown:
-+ vchiq_shutdown(instance);
-+exit:
-+ return 0;
-+}
-+
-+
-+
-+VCHIQ_STATUS_T
-+vchiq_arm_init_state(VCHIQ_STATE_T *state, VCHIQ_ARM_STATE_T *arm_state)
-+{
-+ VCHIQ_STATUS_T status = VCHIQ_SUCCESS;
-+
-+ if (arm_state) {
-+ rwlock_init(&arm_state->susp_res_lock);
-+
-+ init_completion(&arm_state->ka_evt);
-+ atomic_set(&arm_state->ka_use_count, 0);
-+ atomic_set(&arm_state->ka_use_ack_count, 0);
-+ atomic_set(&arm_state->ka_release_count, 0);
-+
-+ init_completion(&arm_state->vc_suspend_complete);
-+
-+ init_completion(&arm_state->vc_resume_complete);
-+ /* Initialise to 'done' state. We only want to block on resume
-+ * completion while videocore is suspended. */
-+ set_resume_state(arm_state, VC_RESUME_RESUMED);
-+
-+ init_completion(&arm_state->resume_blocker);
-+ /* Initialise to 'done' state. We only want to block on this
-+ * completion while resume is blocked */
-+ complete_all(&arm_state->resume_blocker);
-+
-+ init_completion(&arm_state->blocked_blocker);
-+ /* Initialise to 'done' state. We only want to block on this
-+ * completion while things are waiting on the resume blocker */
-+ complete_all(&arm_state->blocked_blocker);
-+
-+ arm_state->suspend_timer_timeout = SUSPEND_TIMER_TIMEOUT_MS;
-+ arm_state->suspend_timer_running = 0;
-+ init_timer(&arm_state->suspend_timer);
-+ arm_state->suspend_timer.data = (unsigned long)(state);
-+ arm_state->suspend_timer.function = suspend_timer_callback;
-+
-+ arm_state->first_connect = 0;
-+
-+ }
-+ return status;
-+}
-+
-+/*
-+** Functions to modify the state variables;
-+** set_suspend_state
-+** set_resume_state
-+**
-+** There are more state variables than we might like, so ensure they remain in
-+** step. Suspend and resume state are maintained separately, since most of
-+** these state machines can operate independently. However, there are a few
-+** states where state transitions in one state machine cause a reset to the
-+** other state machine. In addition, there are some completion events which
-+** need to occur on state machine reset and end-state(s), so these are also
-+** dealt with in these functions.
-+**
-+** In all states we set the state variable according to the input, but in some
-+** cases we perform additional steps outlined below;
-+**
-+** VC_SUSPEND_IDLE - Initialise the suspend completion at the same time.
-+** The suspend completion is completed after any suspend
-+** attempt. When we reset the state machine we also reset
-+** the completion. This reset occurs when videocore is
-+** resumed, and also if we initiate suspend after a suspend
-+** failure.
-+**
-+** VC_SUSPEND_IN_PROGRESS - This state is considered the point of no return for
-+** suspend - ie from this point on we must try to suspend
-+** before resuming can occur. We therefore also reset the
-+** resume state machine to VC_RESUME_IDLE in this state.
-+**
-+** VC_SUSPEND_SUSPENDED - Suspend has completed successfully. Also call
-+** complete_all on the suspend completion to notify
-+** anything waiting for suspend to happen.
-+**
-+** VC_SUSPEND_REJECTED - Videocore rejected suspend. Videocore will also
-+** initiate resume, so no need to alter resume state.
-+** We call complete_all on the suspend completion to notify
-+** of suspend rejection.
-+**
-+** VC_SUSPEND_FAILED - We failed to initiate videocore suspend. We notify the
-+** suspend completion and reset the resume state machine.
-+**
-+** VC_RESUME_IDLE - Initialise the resume completion at the same time. The
-+** resume completion is in it's 'done' state whenever
-+** videcore is running. Therfore, the VC_RESUME_IDLE state
-+** implies that videocore is suspended.
-+** Hence, any thread which needs to wait until videocore is
-+** running can wait on this completion - it will only block
-+** if videocore is suspended.
-+**
-+** VC_RESUME_RESUMED - Resume has completed successfully. Videocore is running.
-+** Call complete_all on the resume completion to unblock
-+** any threads waiting for resume. Also reset the suspend
-+** state machine to it's idle state.
-+**
-+** VC_RESUME_FAILED - Currently unused - no mechanism to fail resume exists.
-+*/
-+
-+void
-+set_suspend_state(VCHIQ_ARM_STATE_T *arm_state,
-+ enum vc_suspend_status new_state)
-+{
-+ /* set the state in all cases */
-+ arm_state->vc_suspend_state = new_state;
-+
-+ /* state specific additional actions */
-+ switch (new_state) {
-+ case VC_SUSPEND_FORCE_CANCELED:
-+ complete_all(&arm_state->vc_suspend_complete);
-+ break;
-+ case VC_SUSPEND_REJECTED:
-+ complete_all(&arm_state->vc_suspend_complete);
-+ break;
-+ case VC_SUSPEND_FAILED:
-+ complete_all(&arm_state->vc_suspend_complete);
-+ arm_state->vc_resume_state = VC_RESUME_RESUMED;
-+ complete_all(&arm_state->vc_resume_complete);
-+ break;
-+ case VC_SUSPEND_IDLE:
-+ reinit_completion(&arm_state->vc_suspend_complete);
-+ break;
-+ case VC_SUSPEND_REQUESTED:
-+ break;
-+ case VC_SUSPEND_IN_PROGRESS:
-+ set_resume_state(arm_state, VC_RESUME_IDLE);
-+ break;
-+ case VC_SUSPEND_SUSPENDED:
-+ complete_all(&arm_state->vc_suspend_complete);
-+ break;
-+ default:
-+ BUG();
-+ break;
-+ }
-+}
-+
-+void
-+set_resume_state(VCHIQ_ARM_STATE_T *arm_state,
-+ enum vc_resume_status new_state)
-+{
-+ /* set the state in all cases */
-+ arm_state->vc_resume_state = new_state;
-+
-+ /* state specific additional actions */
-+ switch (new_state) {
-+ case VC_RESUME_FAILED:
-+ break;
-+ case VC_RESUME_IDLE:
-+ reinit_completion(&arm_state->vc_resume_complete);
-+ break;
-+ case VC_RESUME_REQUESTED:
-+ break;
-+ case VC_RESUME_IN_PROGRESS:
-+ break;
-+ case VC_RESUME_RESUMED:
-+ complete_all(&arm_state->vc_resume_complete);
-+ set_suspend_state(arm_state, VC_SUSPEND_IDLE);
-+ break;
-+ default:
-+ BUG();
-+ break;
-+ }
-+}
-+
-+
-+/* should be called with the write lock held */
-+inline void
-+start_suspend_timer(VCHIQ_ARM_STATE_T *arm_state)
-+{
-+ del_timer(&arm_state->suspend_timer);
-+ arm_state->suspend_timer.expires = jiffies +
-+ msecs_to_jiffies(arm_state->
-+ suspend_timer_timeout);
-+ add_timer(&arm_state->suspend_timer);
-+ arm_state->suspend_timer_running = 1;
-+}
-+
-+/* should be called with the write lock held */
-+static inline void
-+stop_suspend_timer(VCHIQ_ARM_STATE_T *arm_state)
-+{
-+ if (arm_state->suspend_timer_running) {
-+ del_timer(&arm_state->suspend_timer);
-+ arm_state->suspend_timer_running = 0;
-+ }
-+}
-+
-+static inline int
-+need_resume(VCHIQ_STATE_T *state)
-+{
-+ VCHIQ_ARM_STATE_T *arm_state = vchiq_platform_get_arm_state(state);
-+ return (arm_state->vc_suspend_state > VC_SUSPEND_IDLE) &&
-+ (arm_state->vc_resume_state < VC_RESUME_REQUESTED) &&
-+ vchiq_videocore_wanted(state);
-+}
-+
-+static int
-+block_resume(VCHIQ_ARM_STATE_T *arm_state)
-+{
-+ int status = VCHIQ_SUCCESS;
-+ const unsigned long timeout_val =
-+ msecs_to_jiffies(FORCE_SUSPEND_TIMEOUT_MS);
-+ int resume_count = 0;
-+
-+ /* Allow any threads which were blocked by the last force suspend to
-+ * complete if they haven't already. Only give this one shot; if
-+ * blocked_count is incremented after blocked_blocker is completed
-+ * (which only happens when blocked_count hits 0) then those threads
-+ * will have to wait until next time around */
-+ if (arm_state->blocked_count) {
-+ reinit_completion(&arm_state->blocked_blocker);
-+ write_unlock_bh(&arm_state->susp_res_lock);
-+ vchiq_log_info(vchiq_susp_log_level, "%s wait for previously "
-+ "blocked clients", __func__);
-+ if (wait_for_completion_interruptible_timeout(
-+ &arm_state->blocked_blocker, timeout_val)
-+ <= 0) {
-+ vchiq_log_error(vchiq_susp_log_level, "%s wait for "
-+ "previously blocked clients failed" , __func__);
-+ status = VCHIQ_ERROR;
-+ write_lock_bh(&arm_state->susp_res_lock);
-+ goto out;
-+ }
-+ vchiq_log_info(vchiq_susp_log_level, "%s previously blocked "
-+ "clients resumed", __func__);
-+ write_lock_bh(&arm_state->susp_res_lock);
-+ }
-+
-+ /* We need to wait for resume to complete if it's in process */
-+ while (arm_state->vc_resume_state != VC_RESUME_RESUMED &&
-+ arm_state->vc_resume_state > VC_RESUME_IDLE) {
-+ if (resume_count > 1) {
-+ status = VCHIQ_ERROR;
-+ vchiq_log_error(vchiq_susp_log_level, "%s waited too "
-+ "many times for resume" , __func__);
-+ goto out;
-+ }
-+ write_unlock_bh(&arm_state->susp_res_lock);
-+ vchiq_log_info(vchiq_susp_log_level, "%s wait for resume",
-+ __func__);
-+ if (wait_for_completion_interruptible_timeout(
-+ &arm_state->vc_resume_complete, timeout_val)
-+ <= 0) {
-+ vchiq_log_error(vchiq_susp_log_level, "%s wait for "
-+ "resume failed (%s)", __func__,
-+ resume_state_names[arm_state->vc_resume_state +
-+ VC_RESUME_NUM_OFFSET]);
-+ status = VCHIQ_ERROR;
-+ write_lock_bh(&arm_state->susp_res_lock);
-+ goto out;
-+ }
-+ vchiq_log_info(vchiq_susp_log_level, "%s resumed", __func__);
-+ write_lock_bh(&arm_state->susp_res_lock);
-+ resume_count++;
-+ }
-+ reinit_completion(&arm_state->resume_blocker);
-+ arm_state->resume_blocked = 1;
-+
-+out:
-+ return status;
-+}
-+
-+static inline void
-+unblock_resume(VCHIQ_ARM_STATE_T *arm_state)
-+{
-+ complete_all(&arm_state->resume_blocker);
-+ arm_state->resume_blocked = 0;
-+}
-+
-+/* Initiate suspend via slot handler. Should be called with the write lock
-+ * held */
-+VCHIQ_STATUS_T
-+vchiq_arm_vcsuspend(VCHIQ_STATE_T *state)
-+{
-+ VCHIQ_STATUS_T status = VCHIQ_ERROR;
-+ VCHIQ_ARM_STATE_T *arm_state = vchiq_platform_get_arm_state(state);
-+
-+ if (!arm_state)
-+ goto out;
-+
-+ vchiq_log_trace(vchiq_susp_log_level, "%s", __func__);
-+ status = VCHIQ_SUCCESS;
-+
-+
-+ switch (arm_state->vc_suspend_state) {
-+ case VC_SUSPEND_REQUESTED:
-+ vchiq_log_info(vchiq_susp_log_level, "%s: suspend already "
-+ "requested", __func__);
-+ break;
-+ case VC_SUSPEND_IN_PROGRESS:
-+ vchiq_log_info(vchiq_susp_log_level, "%s: suspend already in "
-+ "progress", __func__);
-+ break;
-+
-+ default:
-+ /* We don't expect to be in other states, so log but continue
-+ * anyway */
-+ vchiq_log_error(vchiq_susp_log_level,
-+ "%s unexpected suspend state %s", __func__,
-+ suspend_state_names[arm_state->vc_suspend_state +
-+ VC_SUSPEND_NUM_OFFSET]);
-+ /* fall through */
-+ case VC_SUSPEND_REJECTED:
-+ case VC_SUSPEND_FAILED:
-+ /* Ensure any idle state actions have been run */
-+ set_suspend_state(arm_state, VC_SUSPEND_IDLE);
-+ /* fall through */
-+ case VC_SUSPEND_IDLE:
-+ vchiq_log_info(vchiq_susp_log_level,
-+ "%s: suspending", __func__);
-+ set_suspend_state(arm_state, VC_SUSPEND_REQUESTED);
-+ /* kick the slot handler thread to initiate suspend */
-+ request_poll(state, NULL, 0);
-+ break;
-+ }
-+
-+out:
-+ vchiq_log_trace(vchiq_susp_log_level, "%s exit %d", __func__, status);
-+ return status;
-+}
-+
-+void
-+vchiq_platform_check_suspend(VCHIQ_STATE_T *state)
-+{
-+ VCHIQ_ARM_STATE_T *arm_state = vchiq_platform_get_arm_state(state);
-+ int susp = 0;
-+
-+ if (!arm_state)
-+ goto out;
-+
-+ vchiq_log_trace(vchiq_susp_log_level, "%s", __func__);
-+
-+ write_lock_bh(&arm_state->susp_res_lock);
-+ if (arm_state->vc_suspend_state == VC_SUSPEND_REQUESTED &&
-+ arm_state->vc_resume_state == VC_RESUME_RESUMED) {
-+ set_suspend_state(arm_state, VC_SUSPEND_IN_PROGRESS);
-+ susp = 1;
-+ }
-+ write_unlock_bh(&arm_state->susp_res_lock);
-+
-+ if (susp)
-+ vchiq_platform_suspend(state);
-+
-+out:
-+ vchiq_log_trace(vchiq_susp_log_level, "%s exit", __func__);
-+ return;
-+}
-+
-+
-+static void
-+output_timeout_error(VCHIQ_STATE_T *state)
-+{
-+ VCHIQ_ARM_STATE_T *arm_state = vchiq_platform_get_arm_state(state);
-+ char service_err[50] = "";
-+ int vc_use_count = arm_state->videocore_use_count;
-+ int active_services = state->unused_service;
-+ int i;
-+
-+ if (!arm_state->videocore_use_count) {
-+ snprintf(service_err, 50, " Videocore usecount is 0");
-+ goto output_msg;
-+ }
-+ for (i = 0; i < active_services; i++) {
-+ VCHIQ_SERVICE_T *service_ptr = state->services[i];
-+ if (service_ptr && service_ptr->service_use_count &&
-+ (service_ptr->srvstate != VCHIQ_SRVSTATE_FREE)) {
-+ snprintf(service_err, 50, " %c%c%c%c(%d) service has "
-+ "use count %d%s", VCHIQ_FOURCC_AS_4CHARS(
-+ service_ptr->base.fourcc),
-+ service_ptr->client_id,
-+ service_ptr->service_use_count,
-+ service_ptr->service_use_count ==
-+ vc_use_count ? "" : " (+ more)");
-+ break;
-+ }
-+ }
-+
-+output_msg:
-+ vchiq_log_error(vchiq_susp_log_level,
-+ "timed out waiting for vc suspend (%d).%s",
-+ arm_state->autosuspend_override, service_err);
-+
-+}
-+
-+/* Try to get videocore into suspended state, regardless of autosuspend state.
-+** We don't actually force suspend, since videocore may get into a bad state
-+** if we force suspend at a bad time. Instead, we wait for autosuspend to
-+** determine a good point to suspend. If this doesn't happen within 100ms we
-+** report failure.
-+**
-+** Returns VCHIQ_SUCCESS if videocore suspended successfully, VCHIQ_RETRY if
-+** videocore failed to suspend in time or VCHIQ_ERROR if interrupted.
-+*/
-+VCHIQ_STATUS_T
-+vchiq_arm_force_suspend(VCHIQ_STATE_T *state)
-+{
-+ VCHIQ_ARM_STATE_T *arm_state = vchiq_platform_get_arm_state(state);
-+ VCHIQ_STATUS_T status = VCHIQ_ERROR;
-+ long rc = 0;
-+ int repeat = -1;
-+
-+ if (!arm_state)
-+ goto out;
-+
-+ vchiq_log_trace(vchiq_susp_log_level, "%s", __func__);
-+
-+ write_lock_bh(&arm_state->susp_res_lock);
-+
-+ status = block_resume(arm_state);
-+ if (status != VCHIQ_SUCCESS)
-+ goto unlock;
-+ if (arm_state->vc_suspend_state == VC_SUSPEND_SUSPENDED) {
-+ /* Already suspended - just block resume and exit */
-+ vchiq_log_info(vchiq_susp_log_level, "%s already suspended",
-+ __func__);
-+ status = VCHIQ_SUCCESS;
-+ goto unlock;
-+ } else if (arm_state->vc_suspend_state <= VC_SUSPEND_IDLE) {
-+ /* initiate suspend immediately in the case that we're waiting
-+ * for the timeout */
-+ stop_suspend_timer(arm_state);
-+ if (!vchiq_videocore_wanted(state)) {
-+ vchiq_log_info(vchiq_susp_log_level, "%s videocore "
-+ "idle, initiating suspend", __func__);
-+ status = vchiq_arm_vcsuspend(state);
-+ } else if (arm_state->autosuspend_override <
-+ FORCE_SUSPEND_FAIL_MAX) {
-+ vchiq_log_info(vchiq_susp_log_level, "%s letting "
-+ "videocore go idle", __func__);
-+ status = VCHIQ_SUCCESS;
-+ } else {
-+ vchiq_log_warning(vchiq_susp_log_level, "%s failed too "
-+ "many times - attempting suspend", __func__);
-+ status = vchiq_arm_vcsuspend(state);
-+ }
-+ } else {
-+ vchiq_log_info(vchiq_susp_log_level, "%s videocore suspend "
-+ "in progress - wait for completion", __func__);
-+ status = VCHIQ_SUCCESS;
-+ }
-+
-+ /* Wait for suspend to happen due to system idle (not forced..) */
-+ if (status != VCHIQ_SUCCESS)
-+ goto unblock_resume;
-+
-+ do {
-+ write_unlock_bh(&arm_state->susp_res_lock);
-+
-+ rc = wait_for_completion_interruptible_timeout(
-+ &arm_state->vc_suspend_complete,
-+ msecs_to_jiffies(FORCE_SUSPEND_TIMEOUT_MS));
-+
-+ write_lock_bh(&arm_state->susp_res_lock);
-+ if (rc < 0) {
-+ vchiq_log_warning(vchiq_susp_log_level, "%s "
-+ "interrupted waiting for suspend", __func__);
-+ status = VCHIQ_ERROR;
-+ goto unblock_resume;
-+ } else if (rc == 0) {
-+ if (arm_state->vc_suspend_state > VC_SUSPEND_IDLE) {
-+ /* Repeat timeout once if in progress */
-+ if (repeat < 0) {
-+ repeat = 1;
-+ continue;
-+ }
-+ }
-+ arm_state->autosuspend_override++;
-+ output_timeout_error(state);
-+
-+ status = VCHIQ_RETRY;
-+ goto unblock_resume;
-+ }
-+ } while (0 < (repeat--));
-+
-+ /* Check and report state in case we need to abort ARM suspend */
-+ if (arm_state->vc_suspend_state != VC_SUSPEND_SUSPENDED) {
-+ status = VCHIQ_RETRY;
-+ vchiq_log_error(vchiq_susp_log_level,
-+ "%s videocore suspend failed (state %s)", __func__,
-+ suspend_state_names[arm_state->vc_suspend_state +
-+ VC_SUSPEND_NUM_OFFSET]);
-+ /* Reset the state only if it's still in an error state.
-+ * Something could have already initiated another suspend. */
-+ if (arm_state->vc_suspend_state < VC_SUSPEND_IDLE)
-+ set_suspend_state(arm_state, VC_SUSPEND_IDLE);
-+
-+ goto unblock_resume;
-+ }
-+
-+ /* successfully suspended - unlock and exit */
-+ goto unlock;
-+
-+unblock_resume:
-+ /* all error states need to unblock resume before exit */
-+ unblock_resume(arm_state);
-+
-+unlock:
-+ write_unlock_bh(&arm_state->susp_res_lock);
-+
-+out:
-+ vchiq_log_trace(vchiq_susp_log_level, "%s exit %d", __func__, status);
-+ return status;
-+}
-+
-+void
-+vchiq_check_suspend(VCHIQ_STATE_T *state)
-+{
-+ VCHIQ_ARM_STATE_T *arm_state = vchiq_platform_get_arm_state(state);
-+
-+ if (!arm_state)
-+ goto out;
-+
-+ vchiq_log_trace(vchiq_susp_log_level, "%s", __func__);
-+
-+ write_lock_bh(&arm_state->susp_res_lock);
-+ if (arm_state->vc_suspend_state != VC_SUSPEND_SUSPENDED &&
-+ arm_state->first_connect &&
-+ !vchiq_videocore_wanted(state)) {
-+ vchiq_arm_vcsuspend(state);
-+ }
-+ write_unlock_bh(&arm_state->susp_res_lock);
-+
-+out:
-+ vchiq_log_trace(vchiq_susp_log_level, "%s exit", __func__);
-+ return;
-+}
-+
-+
-+int
-+vchiq_arm_allow_resume(VCHIQ_STATE_T *state)
-+{
-+ VCHIQ_ARM_STATE_T *arm_state = vchiq_platform_get_arm_state(state);
-+ int resume = 0;
-+ int ret = -1;
-+
-+ if (!arm_state)
-+ goto out;
-+
-+ vchiq_log_trace(vchiq_susp_log_level, "%s", __func__);
-+
-+ write_lock_bh(&arm_state->susp_res_lock);
-+ unblock_resume(arm_state);
-+ resume = vchiq_check_resume(state);
-+ write_unlock_bh(&arm_state->susp_res_lock);
-+
-+ if (resume) {
-+ if (wait_for_completion_interruptible(
-+ &arm_state->vc_resume_complete) < 0) {
-+ vchiq_log_error(vchiq_susp_log_level,
-+ "%s interrupted", __func__);
-+ /* failed, cannot accurately derive suspend
-+ * state, so exit early. */
-+ goto out;
-+ }
-+ }
-+
-+ read_lock_bh(&arm_state->susp_res_lock);
-+ if (arm_state->vc_suspend_state == VC_SUSPEND_SUSPENDED) {
-+ vchiq_log_info(vchiq_susp_log_level,
-+ "%s: Videocore remains suspended", __func__);
-+ } else {
-+ vchiq_log_info(vchiq_susp_log_level,
-+ "%s: Videocore resumed", __func__);
-+ ret = 0;
-+ }
-+ read_unlock_bh(&arm_state->susp_res_lock);
-+out:
-+ vchiq_log_trace(vchiq_susp_log_level, "%s exit %d", __func__, ret);
-+ return ret;
-+}
-+
-+/* This function should be called with the write lock held */
-+int
-+vchiq_check_resume(VCHIQ_STATE_T *state)
-+{
-+ VCHIQ_ARM_STATE_T *arm_state = vchiq_platform_get_arm_state(state);
-+ int resume = 0;
-+
-+ if (!arm_state)
-+ goto out;
-+
-+ vchiq_log_trace(vchiq_susp_log_level, "%s", __func__);
-+
-+ if (need_resume(state)) {
-+ set_resume_state(arm_state, VC_RESUME_REQUESTED);
-+ request_poll(state, NULL, 0);
-+ resume = 1;
-+ }
-+
-+out:
-+ vchiq_log_trace(vchiq_susp_log_level, "%s exit", __func__);
-+ return resume;
-+}
-+
-+void
-+vchiq_platform_check_resume(VCHIQ_STATE_T *state)
-+{
-+ VCHIQ_ARM_STATE_T *arm_state = vchiq_platform_get_arm_state(state);
-+ int res = 0;
-+
-+ if (!arm_state)
-+ goto out;
-+
-+ vchiq_log_trace(vchiq_susp_log_level, "%s", __func__);
-+
-+ write_lock_bh(&arm_state->susp_res_lock);
-+ if (arm_state->wake_address == 0) {
-+ vchiq_log_info(vchiq_susp_log_level,
-+ "%s: already awake", __func__);
-+ goto unlock;
-+ }
-+ if (arm_state->vc_resume_state == VC_RESUME_IN_PROGRESS) {
-+ vchiq_log_info(vchiq_susp_log_level,
-+ "%s: already resuming", __func__);
-+ goto unlock;
-+ }
-+
-+ if (arm_state->vc_resume_state == VC_RESUME_REQUESTED) {
-+ set_resume_state(arm_state, VC_RESUME_IN_PROGRESS);
-+ res = 1;
-+ } else
-+ vchiq_log_trace(vchiq_susp_log_level,
-+ "%s: not resuming (resume state %s)", __func__,
-+ resume_state_names[arm_state->vc_resume_state +
-+ VC_RESUME_NUM_OFFSET]);
-+
-+unlock:
-+ write_unlock_bh(&arm_state->susp_res_lock);
-+
-+ if (res)
-+ vchiq_platform_resume(state);
-+
-+out:
-+ vchiq_log_trace(vchiq_susp_log_level, "%s exit", __func__);
-+ return;
-+
-+}
-+
-+
-+
-+VCHIQ_STATUS_T
-+vchiq_use_internal(VCHIQ_STATE_T *state, VCHIQ_SERVICE_T *service,
-+ enum USE_TYPE_E use_type)
-+{
-+ VCHIQ_ARM_STATE_T *arm_state = vchiq_platform_get_arm_state(state);
-+ VCHIQ_STATUS_T ret = VCHIQ_SUCCESS;
-+ char entity[16];
-+ int *entity_uc;
-+ int local_uc, local_entity_uc;
-+
-+ if (!arm_state)
-+ goto out;
-+
-+ vchiq_log_trace(vchiq_susp_log_level, "%s", __func__);
-+
-+ if (use_type == USE_TYPE_VCHIQ) {
-+ sprintf(entity, "VCHIQ: ");
-+ entity_uc = &arm_state->peer_use_count;
-+ } else if (service) {
-+ sprintf(entity, "%c%c%c%c:%03d",
-+ VCHIQ_FOURCC_AS_4CHARS(service->base.fourcc),
-+ service->client_id);
-+ entity_uc = &service->service_use_count;
-+ } else {
-+ vchiq_log_error(vchiq_susp_log_level, "%s null service "
-+ "ptr", __func__);
-+ ret = VCHIQ_ERROR;
-+ goto out;
-+ }
-+
-+ write_lock_bh(&arm_state->susp_res_lock);
-+ while (arm_state->resume_blocked) {
-+ /* If we call 'use' while force suspend is waiting for suspend,
-+ * then we're about to block the thread which the force is
-+ * waiting to complete, so we're bound to just time out. In this
-+ * case, set the suspend state such that the wait will be
-+ * canceled, so we can complete as quickly as possible. */
-+ if (arm_state->resume_blocked && arm_state->vc_suspend_state ==
-+ VC_SUSPEND_IDLE) {
-+ set_suspend_state(arm_state, VC_SUSPEND_FORCE_CANCELED);
-+ break;
-+ }
-+ /* If suspend is already in progress then we need to block */
-+ if (!try_wait_for_completion(&arm_state->resume_blocker)) {
-+ /* Indicate that there are threads waiting on the resume
-+ * blocker. These need to be allowed to complete before
-+ * a _second_ call to force suspend can complete,
-+ * otherwise low priority threads might never actually
-+ * continue */
-+ arm_state->blocked_count++;
-+ write_unlock_bh(&arm_state->susp_res_lock);
-+ vchiq_log_info(vchiq_susp_log_level, "%s %s resume "
-+ "blocked - waiting...", __func__, entity);
-+ if (wait_for_completion_killable(
-+ &arm_state->resume_blocker) != 0) {
-+ vchiq_log_error(vchiq_susp_log_level, "%s %s "
-+ "wait for resume blocker interrupted",
-+ __func__, entity);
-+ ret = VCHIQ_ERROR;
-+ write_lock_bh(&arm_state->susp_res_lock);
-+ arm_state->blocked_count--;
-+ write_unlock_bh(&arm_state->susp_res_lock);
-+ goto out;
-+ }
-+ vchiq_log_info(vchiq_susp_log_level, "%s %s resume "
-+ "unblocked", __func__, entity);
-+ write_lock_bh(&arm_state->susp_res_lock);
-+ if (--arm_state->blocked_count == 0)
-+ complete_all(&arm_state->blocked_blocker);
-+ }
-+ }
-+
-+ stop_suspend_timer(arm_state);
-+
-+ local_uc = ++arm_state->videocore_use_count;
-+ local_entity_uc = ++(*entity_uc);
-+
-+ /* If there's a pending request which hasn't yet been serviced then
-+ * just clear it. If we're past VC_SUSPEND_REQUESTED state then
-+ * vc_resume_complete will block until we either resume or fail to
-+ * suspend */
-+ if (arm_state->vc_suspend_state <= VC_SUSPEND_REQUESTED)
-+ set_suspend_state(arm_state, VC_SUSPEND_IDLE);
-+
-+ if ((use_type != USE_TYPE_SERVICE_NO_RESUME) && need_resume(state)) {
-+ set_resume_state(arm_state, VC_RESUME_REQUESTED);
-+ vchiq_log_info(vchiq_susp_log_level,
-+ "%s %s count %d, state count %d",
-+ __func__, entity, local_entity_uc, local_uc);
-+ request_poll(state, NULL, 0);
-+ } else
-+ vchiq_log_trace(vchiq_susp_log_level,
-+ "%s %s count %d, state count %d",
-+ __func__, entity, *entity_uc, local_uc);
-+
-+
-+ write_unlock_bh(&arm_state->susp_res_lock);
-+
-+ /* Completion is in a done state when we're not suspended, so this won't
-+ * block for the non-suspended case. */
-+ if (!try_wait_for_completion(&arm_state->vc_resume_complete)) {
-+ vchiq_log_info(vchiq_susp_log_level, "%s %s wait for resume",
-+ __func__, entity);
-+ if (wait_for_completion_killable(
-+ &arm_state->vc_resume_complete) != 0) {
-+ vchiq_log_error(vchiq_susp_log_level, "%s %s wait for "
-+ "resume interrupted", __func__, entity);
-+ ret = VCHIQ_ERROR;
-+ goto out;
-+ }
-+ vchiq_log_info(vchiq_susp_log_level, "%s %s resumed", __func__,
-+ entity);
-+ }
-+
-+ if (ret == VCHIQ_SUCCESS) {
-+ VCHIQ_STATUS_T status = VCHIQ_SUCCESS;
-+ long ack_cnt = atomic_xchg(&arm_state->ka_use_ack_count, 0);
-+ while (ack_cnt && (status == VCHIQ_SUCCESS)) {
-+ /* Send the use notify to videocore */
-+ status = vchiq_send_remote_use_active(state);
-+ if (status == VCHIQ_SUCCESS)
-+ ack_cnt--;
-+ else
-+ atomic_add(ack_cnt,
-+ &arm_state->ka_use_ack_count);
-+ }
-+ }
-+
-+out:
-+ vchiq_log_trace(vchiq_susp_log_level, "%s exit %d", __func__, ret);
-+ return ret;
-+}
-+
-+VCHIQ_STATUS_T
-+vchiq_release_internal(VCHIQ_STATE_T *state, VCHIQ_SERVICE_T *service)
-+{
-+ VCHIQ_ARM_STATE_T *arm_state = vchiq_platform_get_arm_state(state);
-+ VCHIQ_STATUS_T ret = VCHIQ_SUCCESS;
-+ char entity[16];
-+ int *entity_uc;
-+ int local_uc, local_entity_uc;
-+
-+ if (!arm_state)
-+ goto out;
-+
-+ vchiq_log_trace(vchiq_susp_log_level, "%s", __func__);
-+
-+ if (service) {
-+ sprintf(entity, "%c%c%c%c:%03d",
-+ VCHIQ_FOURCC_AS_4CHARS(service->base.fourcc),
-+ service->client_id);
-+ entity_uc = &service->service_use_count;
-+ } else {
-+ sprintf(entity, "PEER: ");
-+ entity_uc = &arm_state->peer_use_count;
-+ }
-+
-+ write_lock_bh(&arm_state->susp_res_lock);
-+ if (!arm_state->videocore_use_count || !(*entity_uc)) {
-+ /* Don't use BUG_ON - don't allow user thread to crash kernel */
-+ WARN_ON(!arm_state->videocore_use_count);
-+ WARN_ON(!(*entity_uc));
-+ ret = VCHIQ_ERROR;
-+ goto unlock;
-+ }
-+ local_uc = --arm_state->videocore_use_count;
-+ local_entity_uc = --(*entity_uc);
-+
-+ if (!vchiq_videocore_wanted(state)) {
-+ if (vchiq_platform_use_suspend_timer() &&
-+ !arm_state->resume_blocked) {
-+ /* Only use the timer if we're not trying to force
-+ * suspend (=> resume_blocked) */
-+ start_suspend_timer(arm_state);
-+ } else {
-+ vchiq_log_info(vchiq_susp_log_level,
-+ "%s %s count %d, state count %d - suspending",
-+ __func__, entity, *entity_uc,
-+ arm_state->videocore_use_count);
-+ vchiq_arm_vcsuspend(state);
-+ }
-+ } else
-+ vchiq_log_trace(vchiq_susp_log_level,
-+ "%s %s count %d, state count %d",
-+ __func__, entity, *entity_uc,
-+ arm_state->videocore_use_count);
-+
-+unlock:
-+ write_unlock_bh(&arm_state->susp_res_lock);
-+
-+out:
-+ vchiq_log_trace(vchiq_susp_log_level, "%s exit %d", __func__, ret);
-+ return ret;
-+}
-+
-+void
-+vchiq_on_remote_use(VCHIQ_STATE_T *state)
-+{
-+ VCHIQ_ARM_STATE_T *arm_state = vchiq_platform_get_arm_state(state);
-+ vchiq_log_trace(vchiq_susp_log_level, "%s", __func__);
-+ atomic_inc(&arm_state->ka_use_count);
-+ complete(&arm_state->ka_evt);
-+}
-+
-+void
-+vchiq_on_remote_release(VCHIQ_STATE_T *state)
-+{
-+ VCHIQ_ARM_STATE_T *arm_state = vchiq_platform_get_arm_state(state);
-+ vchiq_log_trace(vchiq_susp_log_level, "%s", __func__);
-+ atomic_inc(&arm_state->ka_release_count);
-+ complete(&arm_state->ka_evt);
-+}
-+
-+VCHIQ_STATUS_T
-+vchiq_use_service_internal(VCHIQ_SERVICE_T *service)
-+{
-+ return vchiq_use_internal(service->state, service, USE_TYPE_SERVICE);
-+}
-+
-+VCHIQ_STATUS_T
-+vchiq_release_service_internal(VCHIQ_SERVICE_T *service)
-+{
-+ return vchiq_release_internal(service->state, service);
-+}
-+
-+VCHIQ_DEBUGFS_NODE_T *
-+vchiq_instance_get_debugfs_node(VCHIQ_INSTANCE_T instance)
-+{
-+ return &instance->debugfs_node;
-+}
-+
-+int
-+vchiq_instance_get_use_count(VCHIQ_INSTANCE_T instance)
-+{
-+ VCHIQ_SERVICE_T *service;
-+ int use_count = 0, i;
-+ i = 0;
-+ while ((service = next_service_by_instance(instance->state,
-+ instance, &i)) != NULL) {
-+ use_count += service->service_use_count;
-+ unlock_service(service);
-+ }
-+ return use_count;
-+}
-+
-+int
-+vchiq_instance_get_pid(VCHIQ_INSTANCE_T instance)
-+{
-+ return instance->pid;
-+}
-+
-+int
-+vchiq_instance_get_trace(VCHIQ_INSTANCE_T instance)
-+{
-+ return instance->trace;
-+}
-+
-+void
-+vchiq_instance_set_trace(VCHIQ_INSTANCE_T instance, int trace)
-+{
-+ VCHIQ_SERVICE_T *service;
-+ int i;
-+ i = 0;
-+ while ((service = next_service_by_instance(instance->state,
-+ instance, &i)) != NULL) {
-+ service->trace = trace;
-+ unlock_service(service);
-+ }
-+ instance->trace = (trace != 0);
-+}
-+
-+static void suspend_timer_callback(unsigned long context)
-+{
-+ VCHIQ_STATE_T *state = (VCHIQ_STATE_T *)context;
-+ VCHIQ_ARM_STATE_T *arm_state = vchiq_platform_get_arm_state(state);
-+ if (!arm_state)
-+ goto out;
-+ vchiq_log_info(vchiq_susp_log_level,
-+ "%s - suspend timer expired - check suspend", __func__);
-+ vchiq_check_suspend(state);
-+out:
-+ return;
-+}
-+
-+VCHIQ_STATUS_T
-+vchiq_use_service_no_resume(VCHIQ_SERVICE_HANDLE_T handle)
-+{
-+ VCHIQ_STATUS_T ret = VCHIQ_ERROR;
-+ VCHIQ_SERVICE_T *service = find_service_by_handle(handle);
-+ if (service) {
-+ ret = vchiq_use_internal(service->state, service,
-+ USE_TYPE_SERVICE_NO_RESUME);
-+ unlock_service(service);
-+ }
-+ return ret;
-+}
-+
-+VCHIQ_STATUS_T
-+vchiq_use_service(VCHIQ_SERVICE_HANDLE_T handle)
-+{
-+ VCHIQ_STATUS_T ret = VCHIQ_ERROR;
-+ VCHIQ_SERVICE_T *service = find_service_by_handle(handle);
-+ if (service) {
-+ ret = vchiq_use_internal(service->state, service,
-+ USE_TYPE_SERVICE);
-+ unlock_service(service);
-+ }
-+ return ret;
-+}
-+
-+VCHIQ_STATUS_T
-+vchiq_release_service(VCHIQ_SERVICE_HANDLE_T handle)
-+{
-+ VCHIQ_STATUS_T ret = VCHIQ_ERROR;
-+ VCHIQ_SERVICE_T *service = find_service_by_handle(handle);
-+ if (service) {
-+ ret = vchiq_release_internal(service->state, service);
-+ unlock_service(service);
-+ }
-+ return ret;
-+}
-+
-+void
-+vchiq_dump_service_use_state(VCHIQ_STATE_T *state)
-+{
-+ VCHIQ_ARM_STATE_T *arm_state = vchiq_platform_get_arm_state(state);
-+ int i, j = 0;
-+ /* Only dump 64 services */
-+ static const int local_max_services = 64;
-+ /* If there's more than 64 services, only dump ones with
-+ * non-zero counts */
-+ int only_nonzero = 0;
-+ static const char *nz = "<-- preventing suspend";
-+
-+ enum vc_suspend_status vc_suspend_state;
-+ enum vc_resume_status vc_resume_state;
-+ int peer_count;
-+ int vc_use_count;
-+ int active_services;
-+ struct service_data_struct {
-+ int fourcc;
-+ int clientid;
-+ int use_count;
-+ } service_data[local_max_services];
-+
-+ if (!arm_state)
-+ return;
-+
-+ read_lock_bh(&arm_state->susp_res_lock);
-+ vc_suspend_state = arm_state->vc_suspend_state;
-+ vc_resume_state = arm_state->vc_resume_state;
-+ peer_count = arm_state->peer_use_count;
-+ vc_use_count = arm_state->videocore_use_count;
-+ active_services = state->unused_service;
-+ if (active_services > local_max_services)
-+ only_nonzero = 1;
-+
-+ for (i = 0; (i < active_services) && (j < local_max_services); i++) {
-+ VCHIQ_SERVICE_T *service_ptr = state->services[i];
-+ if (!service_ptr)
-+ continue;
-+
-+ if (only_nonzero && !service_ptr->service_use_count)
-+ continue;
-+
-+ if (service_ptr->srvstate != VCHIQ_SRVSTATE_FREE) {
-+ service_data[j].fourcc = service_ptr->base.fourcc;
-+ service_data[j].clientid = service_ptr->client_id;
-+ service_data[j++].use_count = service_ptr->
-+ service_use_count;
-+ }
-+ }
-+
-+ read_unlock_bh(&arm_state->susp_res_lock);
-+
-+ vchiq_log_warning(vchiq_susp_log_level,
-+ "-- Videcore suspend state: %s --",
-+ suspend_state_names[vc_suspend_state + VC_SUSPEND_NUM_OFFSET]);
-+ vchiq_log_warning(vchiq_susp_log_level,
-+ "-- Videcore resume state: %s --",
-+ resume_state_names[vc_resume_state + VC_RESUME_NUM_OFFSET]);
-+
-+ if (only_nonzero)
-+ vchiq_log_warning(vchiq_susp_log_level, "Too many active "
-+ "services (%d). Only dumping up to first %d services "
-+ "with non-zero use-count", active_services,
-+ local_max_services);
-+
-+ for (i = 0; i < j; i++) {
-+ vchiq_log_warning(vchiq_susp_log_level,
-+ "----- %c%c%c%c:%d service count %d %s",
-+ VCHIQ_FOURCC_AS_4CHARS(service_data[i].fourcc),
-+ service_data[i].clientid,
-+ service_data[i].use_count,
-+ service_data[i].use_count ? nz : "");
-+ }
-+ vchiq_log_warning(vchiq_susp_log_level,
-+ "----- VCHIQ use count count %d", peer_count);
-+ vchiq_log_warning(vchiq_susp_log_level,
-+ "--- Overall vchiq instance use count %d", vc_use_count);
-+
-+ vchiq_dump_platform_use_state(state);
-+}
-+
-+VCHIQ_STATUS_T
-+vchiq_check_service(VCHIQ_SERVICE_T *service)
-+{
-+ VCHIQ_ARM_STATE_T *arm_state;
-+ VCHIQ_STATUS_T ret = VCHIQ_ERROR;
-+
-+ if (!service || !service->state)
-+ goto out;
-+
-+ vchiq_log_trace(vchiq_susp_log_level, "%s", __func__);
-+
-+ arm_state = vchiq_platform_get_arm_state(service->state);
-+
-+ read_lock_bh(&arm_state->susp_res_lock);
-+ if (service->service_use_count)
-+ ret = VCHIQ_SUCCESS;
-+ read_unlock_bh(&arm_state->susp_res_lock);
-+
-+ if (ret == VCHIQ_ERROR) {
-+ vchiq_log_error(vchiq_susp_log_level,
-+ "%s ERROR - %c%c%c%c:%d service count %d, "
-+ "state count %d, videocore suspend state %s", __func__,
-+ VCHIQ_FOURCC_AS_4CHARS(service->base.fourcc),
-+ service->client_id, service->service_use_count,
-+ arm_state->videocore_use_count,
-+ suspend_state_names[arm_state->vc_suspend_state +
-+ VC_SUSPEND_NUM_OFFSET]);
-+ vchiq_dump_service_use_state(service->state);
-+ }
-+out:
-+ return ret;
-+}
-+
-+/* stub functions */
-+void vchiq_on_remote_use_active(VCHIQ_STATE_T *state)
-+{
-+ (void)state;
-+}
-+
-+void vchiq_platform_conn_state_changed(VCHIQ_STATE_T *state,
-+ VCHIQ_CONNSTATE_T oldstate, VCHIQ_CONNSTATE_T newstate)
-+{
-+ VCHIQ_ARM_STATE_T *arm_state = vchiq_platform_get_arm_state(state);
-+ vchiq_log_info(vchiq_susp_log_level, "%d: %s->%s", state->id,
-+ get_conn_state_name(oldstate), get_conn_state_name(newstate));
-+ if (state->conn_state == VCHIQ_CONNSTATE_CONNECTED) {
-+ write_lock_bh(&arm_state->susp_res_lock);
-+ if (!arm_state->first_connect) {
-+ char threadname[10];
-+ arm_state->first_connect = 1;
-+ write_unlock_bh(&arm_state->susp_res_lock);
-+ snprintf(threadname, sizeof(threadname), "VCHIQka-%d",
-+ state->id);
-+ arm_state->ka_thread = kthread_create(
-+ &vchiq_keepalive_thread_func,
-+ (void *)state,
-+ threadname);
-+ if (arm_state->ka_thread == NULL) {
-+ vchiq_log_error(vchiq_susp_log_level,
-+ "vchiq: FATAL: couldn't create thread %s",
-+ threadname);
-+ } else {
-+ wake_up_process(arm_state->ka_thread);
-+ }
-+ } else
-+ write_unlock_bh(&arm_state->susp_res_lock);
-+ }
-+}
-+
-+static int vchiq_probe(struct platform_device *pdev)
-+{
-+ struct device_node *fw_node;
-+ struct rpi_firmware *fw;
-+ int err;
-+ void *ptr_err;
-+
-+ fw_node = of_parse_phandle(pdev->dev.of_node, "firmware", 0);
-+/* Remove comment when booting without Device Tree is no longer supported
-+ if (!fw_node) {
-+ dev_err(&pdev->dev, "Missing firmware node\n");
-+ return -ENOENT;
-+ }
-+*/
-+ fw = rpi_firmware_get(fw_node);
-+ if (!fw)
-+ return -EPROBE_DEFER;
-+
-+ platform_set_drvdata(pdev, fw);
-+
-+ /* create debugfs entries */
-+ err = vchiq_debugfs_init();
-+ if (err != 0)
-+ goto failed_debugfs_init;
-+
-+ err = alloc_chrdev_region(&vchiq_devid, VCHIQ_MINOR, 1, DEVICE_NAME);
-+ if (err != 0) {
-+ vchiq_log_error(vchiq_arm_log_level,
-+ "Unable to allocate device number");
-+ goto failed_alloc_chrdev;
-+ }
-+ cdev_init(&vchiq_cdev, &vchiq_fops);
-+ vchiq_cdev.owner = THIS_MODULE;
-+ err = cdev_add(&vchiq_cdev, vchiq_devid, 1);
-+ if (err != 0) {
-+ vchiq_log_error(vchiq_arm_log_level,
-+ "Unable to register device");
-+ goto failed_cdev_add;
-+ }
-+
-+ /* create sysfs entries */
-+ vchiq_class = class_create(THIS_MODULE, DEVICE_NAME);
-+ ptr_err = vchiq_class;
-+ if (IS_ERR(ptr_err))
-+ goto failed_class_create;
-+
-+ vchiq_dev = device_create(vchiq_class, NULL,
-+ vchiq_devid, NULL, "vchiq");
-+ ptr_err = vchiq_dev;
-+ if (IS_ERR(ptr_err))
-+ goto failed_device_create;
-+
-+ err = vchiq_platform_init(pdev, &g_state);
-+ if (err != 0)
-+ goto failed_platform_init;
-+
-+ vchiq_log_info(vchiq_arm_log_level,
-+ "vchiq: initialised - version %d (min %d), device %d.%d",
-+ VCHIQ_VERSION, VCHIQ_VERSION_MIN,
-+ MAJOR(vchiq_devid), MINOR(vchiq_devid));
-+
-+ return 0;
-+
-+failed_platform_init:
-+ device_destroy(vchiq_class, vchiq_devid);
-+failed_device_create:
-+ class_destroy(vchiq_class);
-+failed_class_create:
-+ cdev_del(&vchiq_cdev);
-+ err = PTR_ERR(ptr_err);
-+failed_cdev_add:
-+ unregister_chrdev_region(vchiq_devid, 1);
-+failed_alloc_chrdev:
-+ vchiq_debugfs_deinit();
-+failed_debugfs_init:
-+ vchiq_log_warning(vchiq_arm_log_level, "could not load vchiq");
-+ return err;
-+}
-+
-+static int vchiq_remove(struct platform_device *pdev)
-+{
-+ device_destroy(vchiq_class, vchiq_devid);
-+ class_destroy(vchiq_class);
-+ cdev_del(&vchiq_cdev);
-+ unregister_chrdev_region(vchiq_devid, 1);
-+
-+ return 0;
-+}
-+
-+static const struct of_device_id vchiq_of_match[] = {
-+ { .compatible = "brcm,bcm2835-vchiq", },
-+ {},
-+};
-+MODULE_DEVICE_TABLE(of, vchiq_of_match);
-+
-+static struct platform_driver vchiq_driver = {
-+ .driver = {
-+ .name = "bcm2835_vchiq",
-+ .owner = THIS_MODULE,
-+ .of_match_table = vchiq_of_match,
-+ },
-+ .probe = vchiq_probe,
-+ .remove = vchiq_remove,
-+};
-+module_platform_driver(vchiq_driver);
-+
-+MODULE_LICENSE("GPL");
-+MODULE_AUTHOR("Broadcom Corporation");
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_arm.h
-@@ -0,0 +1,220 @@
-+/**
-+ * Copyright (c) 2014 Raspberry Pi (Trading) Ltd. All rights reserved.
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#ifndef VCHIQ_ARM_H
-+#define VCHIQ_ARM_H
-+
-+#include <linux/mutex.h>
-+#include <linux/platform_device.h>
-+#include <linux/semaphore.h>
-+#include <linux/atomic.h>
-+#include "vchiq_core.h"
-+#include "vchiq_debugfs.h"
-+
-+
-+enum vc_suspend_status {
-+ VC_SUSPEND_FORCE_CANCELED = -3, /* Force suspend canceled, too busy */
-+ VC_SUSPEND_REJECTED = -2, /* Videocore rejected suspend request */
-+ VC_SUSPEND_FAILED = -1, /* Videocore suspend failed */
-+ VC_SUSPEND_IDLE = 0, /* VC active, no suspend actions */
-+ VC_SUSPEND_REQUESTED, /* User has requested suspend */
-+ VC_SUSPEND_IN_PROGRESS, /* Slot handler has recvd suspend request */
-+ VC_SUSPEND_SUSPENDED /* Videocore suspend succeeded */
-+};
-+
-+enum vc_resume_status {
-+ VC_RESUME_FAILED = -1, /* Videocore resume failed */
-+ VC_RESUME_IDLE = 0, /* VC suspended, no resume actions */
-+ VC_RESUME_REQUESTED, /* User has requested resume */
-+ VC_RESUME_IN_PROGRESS, /* Slot handler has received resume request */
-+ VC_RESUME_RESUMED /* Videocore resumed successfully (active) */
-+};
-+
-+
-+enum USE_TYPE_E {
-+ USE_TYPE_SERVICE,
-+ USE_TYPE_SERVICE_NO_RESUME,
-+ USE_TYPE_VCHIQ
-+};
-+
-+
-+
-+typedef struct vchiq_arm_state_struct {
-+ /* Keepalive-related data */
-+ struct task_struct *ka_thread;
-+ struct completion ka_evt;
-+ atomic_t ka_use_count;
-+ atomic_t ka_use_ack_count;
-+ atomic_t ka_release_count;
-+
-+ struct completion vc_suspend_complete;
-+ struct completion vc_resume_complete;
-+
-+ rwlock_t susp_res_lock;
-+ enum vc_suspend_status vc_suspend_state;
-+ enum vc_resume_status vc_resume_state;
-+
-+ unsigned int wake_address;
-+
-+ struct timer_list suspend_timer;
-+ int suspend_timer_timeout;
-+ int suspend_timer_running;
-+
-+ /* Global use count for videocore.
-+ ** This is equal to the sum of the use counts for all services. When
-+ ** this hits zero the videocore suspend procedure will be initiated.
-+ */
-+ int videocore_use_count;
-+
-+ /* Use count to track requests from videocore peer.
-+ ** This use count is not associated with a service, so needs to be
-+ ** tracked separately with the state.
-+ */
-+ int peer_use_count;
-+
-+ /* Flag to indicate whether resume is blocked. This happens when the
-+ ** ARM is suspending
-+ */
-+ struct completion resume_blocker;
-+ int resume_blocked;
-+ struct completion blocked_blocker;
-+ int blocked_count;
-+
-+ int autosuspend_override;
-+
-+ /* Flag to indicate that the first vchiq connect has made it through.
-+ ** This means that both sides should be fully ready, and we should
-+ ** be able to suspend after this point.
-+ */
-+ int first_connect;
-+
-+ unsigned long long suspend_start_time;
-+ unsigned long long sleep_start_time;
-+ unsigned long long resume_start_time;
-+ unsigned long long last_wake_time;
-+
-+} VCHIQ_ARM_STATE_T;
-+
-+extern int vchiq_arm_log_level;
-+extern int vchiq_susp_log_level;
-+
-+int vchiq_platform_init(struct platform_device *pdev, VCHIQ_STATE_T *state);
-+
-+extern VCHIQ_STATE_T *
-+vchiq_get_state(void);
-+
-+extern VCHIQ_STATUS_T
-+vchiq_arm_vcsuspend(VCHIQ_STATE_T *state);
-+
-+extern VCHIQ_STATUS_T
-+vchiq_arm_force_suspend(VCHIQ_STATE_T *state);
-+
-+extern int
-+vchiq_arm_allow_resume(VCHIQ_STATE_T *state);
-+
-+extern VCHIQ_STATUS_T
-+vchiq_arm_vcresume(VCHIQ_STATE_T *state);
-+
-+extern VCHIQ_STATUS_T
-+vchiq_arm_init_state(VCHIQ_STATE_T *state, VCHIQ_ARM_STATE_T *arm_state);
-+
-+extern int
-+vchiq_check_resume(VCHIQ_STATE_T *state);
-+
-+extern void
-+vchiq_check_suspend(VCHIQ_STATE_T *state);
-+ VCHIQ_STATUS_T
-+vchiq_use_service(VCHIQ_SERVICE_HANDLE_T handle);
-+
-+extern VCHIQ_STATUS_T
-+vchiq_release_service(VCHIQ_SERVICE_HANDLE_T handle);
-+
-+extern VCHIQ_STATUS_T
-+vchiq_check_service(VCHIQ_SERVICE_T *service);
-+
-+extern VCHIQ_STATUS_T
-+vchiq_platform_suspend(VCHIQ_STATE_T *state);
-+
-+extern int
-+vchiq_platform_videocore_wanted(VCHIQ_STATE_T *state);
-+
-+extern int
-+vchiq_platform_use_suspend_timer(void);
-+
-+extern void
-+vchiq_dump_platform_use_state(VCHIQ_STATE_T *state);
-+
-+extern void
-+vchiq_dump_service_use_state(VCHIQ_STATE_T *state);
-+
-+extern VCHIQ_ARM_STATE_T*
-+vchiq_platform_get_arm_state(VCHIQ_STATE_T *state);
-+
-+extern int
-+vchiq_videocore_wanted(VCHIQ_STATE_T *state);
-+
-+extern VCHIQ_STATUS_T
-+vchiq_use_internal(VCHIQ_STATE_T *state, VCHIQ_SERVICE_T *service,
-+ enum USE_TYPE_E use_type);
-+extern VCHIQ_STATUS_T
-+vchiq_release_internal(VCHIQ_STATE_T *state, VCHIQ_SERVICE_T *service);
-+
-+extern VCHIQ_DEBUGFS_NODE_T *
-+vchiq_instance_get_debugfs_node(VCHIQ_INSTANCE_T instance);
-+
-+extern int
-+vchiq_instance_get_use_count(VCHIQ_INSTANCE_T instance);
-+
-+extern int
-+vchiq_instance_get_pid(VCHIQ_INSTANCE_T instance);
-+
-+extern int
-+vchiq_instance_get_trace(VCHIQ_INSTANCE_T instance);
-+
-+extern void
-+vchiq_instance_set_trace(VCHIQ_INSTANCE_T instance, int trace);
-+
-+extern void
-+set_suspend_state(VCHIQ_ARM_STATE_T *arm_state,
-+ enum vc_suspend_status new_state);
-+
-+extern void
-+set_resume_state(VCHIQ_ARM_STATE_T *arm_state,
-+ enum vc_resume_status new_state);
-+
-+extern void
-+start_suspend_timer(VCHIQ_ARM_STATE_T *arm_state);
-+
-+
-+#endif /* VCHIQ_ARM_H */
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_build_info.h
-@@ -0,0 +1,37 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+const char *vchiq_get_build_hostname(void);
-+const char *vchiq_get_build_version(void);
-+const char *vchiq_get_build_time(void);
-+const char *vchiq_get_build_date(void);
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_cfg.h
-@@ -0,0 +1,69 @@
-+/**
-+ * Copyright (c) 2010-2014 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#ifndef VCHIQ_CFG_H
-+#define VCHIQ_CFG_H
-+
-+#define VCHIQ_MAGIC VCHIQ_MAKE_FOURCC('V', 'C', 'H', 'I')
-+/* The version of VCHIQ - change with any non-trivial change */
-+#define VCHIQ_VERSION 8
-+/* The minimum compatible version - update to match VCHIQ_VERSION with any
-+** incompatible change */
-+#define VCHIQ_VERSION_MIN 3
-+
-+/* The version that introduced the VCHIQ_IOC_LIB_VERSION ioctl */
-+#define VCHIQ_VERSION_LIB_VERSION 7
-+
-+/* The version that introduced the VCHIQ_IOC_CLOSE_DELIVERED ioctl */
-+#define VCHIQ_VERSION_CLOSE_DELIVERED 7
-+
-+/* The version that made it safe to use SYNCHRONOUS mode */
-+#define VCHIQ_VERSION_SYNCHRONOUS_MODE 8
-+
-+#define VCHIQ_MAX_STATES 1
-+#define VCHIQ_MAX_SERVICES 4096
-+#define VCHIQ_MAX_SLOTS 128
-+#define VCHIQ_MAX_SLOTS_PER_SIDE 64
-+
-+#define VCHIQ_NUM_CURRENT_BULKS 32
-+#define VCHIQ_NUM_SERVICE_BULKS 4
-+
-+#ifndef VCHIQ_ENABLE_DEBUG
-+#define VCHIQ_ENABLE_DEBUG 1
-+#endif
-+
-+#ifndef VCHIQ_ENABLE_STATS
-+#define VCHIQ_ENABLE_STATS 1
-+#endif
-+
-+#endif /* VCHIQ_CFG_H */
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_connected.c
-@@ -0,0 +1,120 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#include "vchiq_connected.h"
-+#include "vchiq_core.h"
-+#include "vchiq_killable.h"
-+#include <linux/module.h>
-+#include <linux/mutex.h>
-+
-+#define MAX_CALLBACKS 10
-+
-+static int g_connected;
-+static int g_num_deferred_callbacks;
-+static VCHIQ_CONNECTED_CALLBACK_T g_deferred_callback[MAX_CALLBACKS];
-+static int g_once_init;
-+static struct mutex g_connected_mutex;
-+
-+/****************************************************************************
-+*
-+* Function to initialize our lock.
-+*
-+***************************************************************************/
-+
-+static void connected_init(void)
-+{
-+ if (!g_once_init) {
-+ mutex_init(&g_connected_mutex);
-+ g_once_init = 1;
-+ }
-+}
-+
-+/****************************************************************************
-+*
-+* This function is used to defer initialization until the vchiq stack is
-+* initialized. If the stack is already initialized, then the callback will
-+* be made immediately, otherwise it will be deferred until
-+* vchiq_call_connected_callbacks is called.
-+*
-+***************************************************************************/
-+
-+void vchiq_add_connected_callback(VCHIQ_CONNECTED_CALLBACK_T callback)
-+{
-+ connected_init();
-+
-+ if (mutex_lock_interruptible(&g_connected_mutex) != 0)
-+ return;
-+
-+ if (g_connected)
-+ /* We're already connected. Call the callback immediately. */
-+
-+ callback();
-+ else {
-+ if (g_num_deferred_callbacks >= MAX_CALLBACKS)
-+ vchiq_log_error(vchiq_core_log_level,
-+ "There already %d callback registered - "
-+ "please increase MAX_CALLBACKS",
-+ g_num_deferred_callbacks);
-+ else {
-+ g_deferred_callback[g_num_deferred_callbacks] =
-+ callback;
-+ g_num_deferred_callbacks++;
-+ }
-+ }
-+ mutex_unlock(&g_connected_mutex);
-+}
-+
-+/****************************************************************************
-+*
-+* This function is called by the vchiq stack once it has been connected to
-+* the videocore and clients can start to use the stack.
-+*
-+***************************************************************************/
-+
-+void vchiq_call_connected_callbacks(void)
-+{
-+ int i;
-+
-+ connected_init();
-+
-+ if (mutex_lock_interruptible(&g_connected_mutex) != 0)
-+ return;
-+
-+ for (i = 0; i < g_num_deferred_callbacks; i++)
-+ g_deferred_callback[i]();
-+
-+ g_num_deferred_callbacks = 0;
-+ g_connected = 1;
-+ mutex_unlock(&g_connected_mutex);
-+}
-+EXPORT_SYMBOL(vchiq_add_connected_callback);
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_connected.h
-@@ -0,0 +1,50 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#ifndef VCHIQ_CONNECTED_H
-+#define VCHIQ_CONNECTED_H
-+
-+/* ---- Include Files ----------------------------------------------------- */
-+
-+/* ---- Constants and Types ---------------------------------------------- */
-+
-+typedef void (*VCHIQ_CONNECTED_CALLBACK_T)(void);
-+
-+/* ---- Variable Externs ------------------------------------------------- */
-+
-+/* ---- Function Prototypes ---------------------------------------------- */
-+
-+void vchiq_add_connected_callback(VCHIQ_CONNECTED_CALLBACK_T callback);
-+void vchiq_call_connected_callbacks(void);
-+
-+#endif /* VCHIQ_CONNECTED_H */
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_core.c
-@@ -0,0 +1,3934 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#include "vchiq_core.h"
-+#include "vchiq_killable.h"
-+
-+#define VCHIQ_SLOT_HANDLER_STACK 8192
-+
-+#define HANDLE_STATE_SHIFT 12
-+
-+#define SLOT_INFO_FROM_INDEX(state, index) (state->slot_info + (index))
-+#define SLOT_DATA_FROM_INDEX(state, index) (state->slot_data + (index))
-+#define SLOT_INDEX_FROM_DATA(state, data) \
-+ (((unsigned int)((char *)data - (char *)state->slot_data)) / \
-+ VCHIQ_SLOT_SIZE)
-+#define SLOT_INDEX_FROM_INFO(state, info) \
-+ ((unsigned int)(info - state->slot_info))
-+#define SLOT_QUEUE_INDEX_FROM_POS(pos) \
-+ ((int)((unsigned int)(pos) / VCHIQ_SLOT_SIZE))
-+
-+#define BULK_INDEX(x) (x & (VCHIQ_NUM_SERVICE_BULKS - 1))
-+
-+#define SRVTRACE_LEVEL(srv) \
-+ (((srv) && (srv)->trace) ? VCHIQ_LOG_TRACE : vchiq_core_msg_log_level)
-+#define SRVTRACE_ENABLED(srv, lev) \
-+ (((srv) && (srv)->trace) || (vchiq_core_msg_log_level >= (lev)))
-+
-+struct vchiq_open_payload {
-+ int fourcc;
-+ int client_id;
-+ short version;
-+ short version_min;
-+};
-+
-+struct vchiq_openack_payload {
-+ short version;
-+};
-+
-+enum
-+{
-+ QMFLAGS_IS_BLOCKING = (1 << 0),
-+ QMFLAGS_NO_MUTEX_LOCK = (1 << 1),
-+ QMFLAGS_NO_MUTEX_UNLOCK = (1 << 2)
-+};
-+
-+/* we require this for consistency between endpoints */
-+vchiq_static_assert(sizeof(VCHIQ_HEADER_T) == 8);
-+vchiq_static_assert(IS_POW2(sizeof(VCHIQ_HEADER_T)));
-+vchiq_static_assert(IS_POW2(VCHIQ_NUM_CURRENT_BULKS));
-+vchiq_static_assert(IS_POW2(VCHIQ_NUM_SERVICE_BULKS));
-+vchiq_static_assert(IS_POW2(VCHIQ_MAX_SERVICES));
-+vchiq_static_assert(VCHIQ_VERSION >= VCHIQ_VERSION_MIN);
-+
-+/* Run time control of log level, based on KERN_XXX level. */
-+int vchiq_core_log_level = VCHIQ_LOG_DEFAULT;
-+int vchiq_core_msg_log_level = VCHIQ_LOG_DEFAULT;
-+int vchiq_sync_log_level = VCHIQ_LOG_DEFAULT;
-+
-+static atomic_t pause_bulks_count = ATOMIC_INIT(0);
-+
-+static DEFINE_SPINLOCK(service_spinlock);
-+DEFINE_SPINLOCK(bulk_waiter_spinlock);
-+DEFINE_SPINLOCK(quota_spinlock);
-+
-+VCHIQ_STATE_T *vchiq_states[VCHIQ_MAX_STATES];
-+static unsigned int handle_seq;
-+
-+static const char *const srvstate_names[] = {
-+ "FREE",
-+ "HIDDEN",
-+ "LISTENING",
-+ "OPENING",
-+ "OPEN",
-+ "OPENSYNC",
-+ "CLOSESENT",
-+ "CLOSERECVD",
-+ "CLOSEWAIT",
-+ "CLOSED"
-+};
-+
-+static const char *const reason_names[] = {
-+ "SERVICE_OPENED",
-+ "SERVICE_CLOSED",
-+ "MESSAGE_AVAILABLE",
-+ "BULK_TRANSMIT_DONE",
-+ "BULK_RECEIVE_DONE",
-+ "BULK_TRANSMIT_ABORTED",
-+ "BULK_RECEIVE_ABORTED"
-+};
-+
-+static const char *const conn_state_names[] = {
-+ "DISCONNECTED",
-+ "CONNECTING",
-+ "CONNECTED",
-+ "PAUSING",
-+ "PAUSE_SENT",
-+ "PAUSED",
-+ "RESUMING",
-+ "PAUSE_TIMEOUT",
-+ "RESUME_TIMEOUT"
-+};
-+
-+
-+static void
-+release_message_sync(VCHIQ_STATE_T *state, VCHIQ_HEADER_T *header);
-+
-+static const char *msg_type_str(unsigned int msg_type)
-+{
-+ switch (msg_type) {
-+ case VCHIQ_MSG_PADDING: return "PADDING";
-+ case VCHIQ_MSG_CONNECT: return "CONNECT";
-+ case VCHIQ_MSG_OPEN: return "OPEN";
-+ case VCHIQ_MSG_OPENACK: return "OPENACK";
-+ case VCHIQ_MSG_CLOSE: return "CLOSE";
-+ case VCHIQ_MSG_DATA: return "DATA";
-+ case VCHIQ_MSG_BULK_RX: return "BULK_RX";
-+ case VCHIQ_MSG_BULK_TX: return "BULK_TX";
-+ case VCHIQ_MSG_BULK_RX_DONE: return "BULK_RX_DONE";
-+ case VCHIQ_MSG_BULK_TX_DONE: return "BULK_TX_DONE";
-+ case VCHIQ_MSG_PAUSE: return "PAUSE";
-+ case VCHIQ_MSG_RESUME: return "RESUME";
-+ case VCHIQ_MSG_REMOTE_USE: return "REMOTE_USE";
-+ case VCHIQ_MSG_REMOTE_RELEASE: return "REMOTE_RELEASE";
-+ case VCHIQ_MSG_REMOTE_USE_ACTIVE: return "REMOTE_USE_ACTIVE";
-+ }
-+ return "???";
-+}
-+
-+static inline void
-+vchiq_set_service_state(VCHIQ_SERVICE_T *service, int newstate)
-+{
-+ vchiq_log_info(vchiq_core_log_level, "%d: srv:%d %s->%s",
-+ service->state->id, service->localport,
-+ srvstate_names[service->srvstate],
-+ srvstate_names[newstate]);
-+ service->srvstate = newstate;
-+}
-+
-+VCHIQ_SERVICE_T *
-+find_service_by_handle(VCHIQ_SERVICE_HANDLE_T handle)
-+{
-+ VCHIQ_SERVICE_T *service;
-+
-+ spin_lock(&service_spinlock);
-+ service = handle_to_service(handle);
-+ if (service && (service->srvstate != VCHIQ_SRVSTATE_FREE) &&
-+ (service->handle == handle)) {
-+ BUG_ON(service->ref_count == 0);
-+ service->ref_count++;
-+ } else
-+ service = NULL;
-+ spin_unlock(&service_spinlock);
-+
-+ if (!service)
-+ vchiq_log_info(vchiq_core_log_level,
-+ "Invalid service handle 0x%x", handle);
-+
-+ return service;
-+}
-+
-+VCHIQ_SERVICE_T *
-+find_service_by_port(VCHIQ_STATE_T *state, int localport)
-+{
-+ VCHIQ_SERVICE_T *service = NULL;
-+ if ((unsigned int)localport <= VCHIQ_PORT_MAX) {
-+ spin_lock(&service_spinlock);
-+ service = state->services[localport];
-+ if (service && (service->srvstate != VCHIQ_SRVSTATE_FREE)) {
-+ BUG_ON(service->ref_count == 0);
-+ service->ref_count++;
-+ } else
-+ service = NULL;
-+ spin_unlock(&service_spinlock);
-+ }
-+
-+ if (!service)
-+ vchiq_log_info(vchiq_core_log_level,
-+ "Invalid port %d", localport);
-+
-+ return service;
-+}
-+
-+VCHIQ_SERVICE_T *
-+find_service_for_instance(VCHIQ_INSTANCE_T instance,
-+ VCHIQ_SERVICE_HANDLE_T handle) {
-+ VCHIQ_SERVICE_T *service;
-+
-+ spin_lock(&service_spinlock);
-+ service = handle_to_service(handle);
-+ if (service && (service->srvstate != VCHIQ_SRVSTATE_FREE) &&
-+ (service->handle == handle) &&
-+ (service->instance == instance)) {
-+ BUG_ON(service->ref_count == 0);
-+ service->ref_count++;
-+ } else
-+ service = NULL;
-+ spin_unlock(&service_spinlock);
-+
-+ if (!service)
-+ vchiq_log_info(vchiq_core_log_level,
-+ "Invalid service handle 0x%x", handle);
-+
-+ return service;
-+}
-+
-+VCHIQ_SERVICE_T *
-+find_closed_service_for_instance(VCHIQ_INSTANCE_T instance,
-+ VCHIQ_SERVICE_HANDLE_T handle) {
-+ VCHIQ_SERVICE_T *service;
-+
-+ spin_lock(&service_spinlock);
-+ service = handle_to_service(handle);
-+ if (service &&
-+ ((service->srvstate == VCHIQ_SRVSTATE_FREE) ||
-+ (service->srvstate == VCHIQ_SRVSTATE_CLOSED)) &&
-+ (service->handle == handle) &&
-+ (service->instance == instance)) {
-+ BUG_ON(service->ref_count == 0);
-+ service->ref_count++;
-+ } else
-+ service = NULL;
-+ spin_unlock(&service_spinlock);
-+
-+ if (!service)
-+ vchiq_log_info(vchiq_core_log_level,
-+ "Invalid service handle 0x%x", handle);
-+
-+ return service;
-+}
-+
-+VCHIQ_SERVICE_T *
-+next_service_by_instance(VCHIQ_STATE_T *state, VCHIQ_INSTANCE_T instance,
-+ int *pidx)
-+{
-+ VCHIQ_SERVICE_T *service = NULL;
-+ int idx = *pidx;
-+
-+ spin_lock(&service_spinlock);
-+ while (idx < state->unused_service) {
-+ VCHIQ_SERVICE_T *srv = state->services[idx++];
-+ if (srv && (srv->srvstate != VCHIQ_SRVSTATE_FREE) &&
-+ (srv->instance == instance)) {
-+ service = srv;
-+ BUG_ON(service->ref_count == 0);
-+ service->ref_count++;
-+ break;
-+ }
-+ }
-+ spin_unlock(&service_spinlock);
-+
-+ *pidx = idx;
-+
-+ return service;
-+}
-+
-+void
-+lock_service(VCHIQ_SERVICE_T *service)
-+{
-+ spin_lock(&service_spinlock);
-+ BUG_ON(!service || (service->ref_count == 0));
-+ if (service)
-+ service->ref_count++;
-+ spin_unlock(&service_spinlock);
-+}
-+
-+void
-+unlock_service(VCHIQ_SERVICE_T *service)
-+{
-+ VCHIQ_STATE_T *state = service->state;
-+ spin_lock(&service_spinlock);
-+ BUG_ON(!service || (service->ref_count == 0));
-+ if (service && service->ref_count) {
-+ service->ref_count--;
-+ if (!service->ref_count) {
-+ BUG_ON(service->srvstate != VCHIQ_SRVSTATE_FREE);
-+ state->services[service->localport] = NULL;
-+ } else
-+ service = NULL;
-+ }
-+ spin_unlock(&service_spinlock);
-+
-+ if (service && service->userdata_term)
-+ service->userdata_term(service->base.userdata);
-+
-+ kfree(service);
-+}
-+
-+int
-+vchiq_get_client_id(VCHIQ_SERVICE_HANDLE_T handle)
-+{
-+ VCHIQ_SERVICE_T *service = find_service_by_handle(handle);
-+ int id;
-+
-+ id = service ? service->client_id : 0;
-+ if (service)
-+ unlock_service(service);
-+
-+ return id;
-+}
-+
-+void *
-+vchiq_get_service_userdata(VCHIQ_SERVICE_HANDLE_T handle)
-+{
-+ VCHIQ_SERVICE_T *service = handle_to_service(handle);
-+
-+ return service ? service->base.userdata : NULL;
-+}
-+
-+int
-+vchiq_get_service_fourcc(VCHIQ_SERVICE_HANDLE_T handle)
-+{
-+ VCHIQ_SERVICE_T *service = handle_to_service(handle);
-+
-+ return service ? service->base.fourcc : 0;
-+}
-+
-+static void
-+mark_service_closing_internal(VCHIQ_SERVICE_T *service, int sh_thread)
-+{
-+ VCHIQ_STATE_T *state = service->state;
-+ VCHIQ_SERVICE_QUOTA_T *service_quota;
-+
-+ service->closing = 1;
-+
-+ /* Synchronise with other threads. */
-+ mutex_lock(&state->recycle_mutex);
-+ mutex_unlock(&state->recycle_mutex);
-+ if (!sh_thread || (state->conn_state != VCHIQ_CONNSTATE_PAUSE_SENT)) {
-+ /* If we're pausing then the slot_mutex is held until resume
-+ * by the slot handler. Therefore don't try to acquire this
-+ * mutex if we're the slot handler and in the pause sent state.
-+ * We don't need to in this case anyway. */
-+ mutex_lock(&state->slot_mutex);
-+ mutex_unlock(&state->slot_mutex);
-+ }
-+
-+ /* Unblock any sending thread. */
-+ service_quota = &state->service_quotas[service->localport];
-+ up(&service_quota->quota_event);
-+}
-+
-+static void
-+mark_service_closing(VCHIQ_SERVICE_T *service)
-+{
-+ mark_service_closing_internal(service, 0);
-+}
-+
-+static inline VCHIQ_STATUS_T
-+make_service_callback(VCHIQ_SERVICE_T *service, VCHIQ_REASON_T reason,
-+ VCHIQ_HEADER_T *header, void *bulk_userdata)
-+{
-+ VCHIQ_STATUS_T status;
-+ vchiq_log_trace(vchiq_core_log_level, "%d: callback:%d (%s, %x, %x)",
-+ service->state->id, service->localport, reason_names[reason],
-+ (unsigned int)header, (unsigned int)bulk_userdata);
-+ status = service->base.callback(reason, header, service->handle,
-+ bulk_userdata);
-+ if (status == VCHIQ_ERROR) {
-+ vchiq_log_warning(vchiq_core_log_level,
-+ "%d: ignoring ERROR from callback to service %x",
-+ service->state->id, service->handle);
-+ status = VCHIQ_SUCCESS;
-+ }
-+ return status;
-+}
-+
-+inline void
-+vchiq_set_conn_state(VCHIQ_STATE_T *state, VCHIQ_CONNSTATE_T newstate)
-+{
-+ VCHIQ_CONNSTATE_T oldstate = state->conn_state;
-+ vchiq_log_info(vchiq_core_log_level, "%d: %s->%s", state->id,
-+ conn_state_names[oldstate],
-+ conn_state_names[newstate]);
-+ state->conn_state = newstate;
-+ vchiq_platform_conn_state_changed(state, oldstate, newstate);
-+}
-+
-+static inline void
-+remote_event_create(REMOTE_EVENT_T *event)
-+{
-+ event->armed = 0;
-+ /* Don't clear the 'fired' flag because it may already have been set
-+ ** by the other side. */
-+ sema_init(event->event, 0);
-+}
-+
-+static inline void
-+remote_event_destroy(REMOTE_EVENT_T *event)
-+{
-+ (void)event;
-+}
-+
-+static inline int
-+remote_event_wait(REMOTE_EVENT_T *event)
-+{
-+ if (!event->fired) {
-+ event->armed = 1;
-+ dsb();
-+ if (!event->fired) {
-+ if (down_interruptible(event->event) != 0) {
-+ event->armed = 0;
-+ return 0;
-+ }
-+ }
-+ event->armed = 0;
-+ wmb();
-+ }
-+
-+ event->fired = 0;
-+ return 1;
-+}
-+
-+static inline void
-+remote_event_signal_local(REMOTE_EVENT_T *event)
-+{
-+ event->armed = 0;
-+ up(event->event);
-+}
-+
-+static inline void
-+remote_event_poll(REMOTE_EVENT_T *event)
-+{
-+ if (event->fired && event->armed)
-+ remote_event_signal_local(event);
-+}
-+
-+void
-+remote_event_pollall(VCHIQ_STATE_T *state)
-+{
-+ remote_event_poll(&state->local->sync_trigger);
-+ remote_event_poll(&state->local->sync_release);
-+ remote_event_poll(&state->local->trigger);
-+ remote_event_poll(&state->local->recycle);
-+}
-+
-+/* Round up message sizes so that any space at the end of a slot is always big
-+** enough for a header. This relies on header size being a power of two, which
-+** has been verified earlier by a static assertion. */
-+
-+static inline unsigned int
-+calc_stride(unsigned int size)
-+{
-+ /* Allow room for the header */
-+ size += sizeof(VCHIQ_HEADER_T);
-+
-+ /* Round up */
-+ return (size + sizeof(VCHIQ_HEADER_T) - 1) & ~(sizeof(VCHIQ_HEADER_T)
-+ - 1);
-+}
-+
-+/* Called by the slot handler thread */
-+static VCHIQ_SERVICE_T *
-+get_listening_service(VCHIQ_STATE_T *state, int fourcc)
-+{
-+ int i;
-+
-+ WARN_ON(fourcc == VCHIQ_FOURCC_INVALID);
-+
-+ for (i = 0; i < state->unused_service; i++) {
-+ VCHIQ_SERVICE_T *service = state->services[i];
-+ if (service &&
-+ (service->public_fourcc == fourcc) &&
-+ ((service->srvstate == VCHIQ_SRVSTATE_LISTENING) ||
-+ ((service->srvstate == VCHIQ_SRVSTATE_OPEN) &&
-+ (service->remoteport == VCHIQ_PORT_FREE)))) {
-+ lock_service(service);
-+ return service;
-+ }
-+ }
-+
-+ return NULL;
-+}
-+
-+/* Called by the slot handler thread */
-+static VCHIQ_SERVICE_T *
-+get_connected_service(VCHIQ_STATE_T *state, unsigned int port)
-+{
-+ int i;
-+ for (i = 0; i < state->unused_service; i++) {
-+ VCHIQ_SERVICE_T *service = state->services[i];
-+ if (service && (service->srvstate == VCHIQ_SRVSTATE_OPEN)
-+ && (service->remoteport == port)) {
-+ lock_service(service);
-+ return service;
-+ }
-+ }
-+ return NULL;
-+}
-+
-+inline void
-+request_poll(VCHIQ_STATE_T *state, VCHIQ_SERVICE_T *service, int poll_type)
-+{
-+ uint32_t value;
-+
-+ if (service) {
-+ do {
-+ value = atomic_read(&service->poll_flags);
-+ } while (atomic_cmpxchg(&service->poll_flags, value,
-+ value | (1 << poll_type)) != value);
-+
-+ do {
-+ value = atomic_read(&state->poll_services[
-+ service->localport>>5]);
-+ } while (atomic_cmpxchg(
-+ &state->poll_services[service->localport>>5],
-+ value, value | (1 << (service->localport & 0x1f)))
-+ != value);
-+ }
-+
-+ state->poll_needed = 1;
-+ wmb();
-+
-+ /* ... and ensure the slot handler runs. */
-+ remote_event_signal_local(&state->local->trigger);
-+}
-+
-+/* Called from queue_message, by the slot handler and application threads,
-+** with slot_mutex held */
-+static VCHIQ_HEADER_T *
-+reserve_space(VCHIQ_STATE_T *state, int space, int is_blocking)
-+{
-+ VCHIQ_SHARED_STATE_T *local = state->local;
-+ int tx_pos = state->local_tx_pos;
-+ int slot_space = VCHIQ_SLOT_SIZE - (tx_pos & VCHIQ_SLOT_MASK);
-+
-+ if (space > slot_space) {
-+ VCHIQ_HEADER_T *header;
-+ /* Fill the remaining space with padding */
-+ WARN_ON(state->tx_data == NULL);
-+ header = (VCHIQ_HEADER_T *)
-+ (state->tx_data + (tx_pos & VCHIQ_SLOT_MASK));
-+ header->msgid = VCHIQ_MSGID_PADDING;
-+ header->size = slot_space - sizeof(VCHIQ_HEADER_T);
-+
-+ tx_pos += slot_space;
-+ }
-+
-+ /* If necessary, get the next slot. */
-+ if ((tx_pos & VCHIQ_SLOT_MASK) == 0) {
-+ int slot_index;
-+
-+ /* If there is no free slot... */
-+
-+ if (down_trylock(&state->slot_available_event) != 0) {
-+ /* ...wait for one. */
-+
-+ VCHIQ_STATS_INC(state, slot_stalls);
-+
-+ /* But first, flush through the last slot. */
-+ state->local_tx_pos = tx_pos;
-+ local->tx_pos = tx_pos;
-+ remote_event_signal(&state->remote->trigger);
-+
-+ if (!is_blocking ||
-+ (down_interruptible(
-+ &state->slot_available_event) != 0))
-+ return NULL; /* No space available */
-+ }
-+
-+ BUG_ON(tx_pos ==
-+ (state->slot_queue_available * VCHIQ_SLOT_SIZE));
-+
-+ slot_index = local->slot_queue[
-+ SLOT_QUEUE_INDEX_FROM_POS(tx_pos) &
-+ VCHIQ_SLOT_QUEUE_MASK];
-+ state->tx_data =
-+ (char *)SLOT_DATA_FROM_INDEX(state, slot_index);
-+ }
-+
-+ state->local_tx_pos = tx_pos + space;
-+
-+ return (VCHIQ_HEADER_T *)(state->tx_data + (tx_pos & VCHIQ_SLOT_MASK));
-+}
-+
-+/* Called by the recycle thread. */
-+static void
-+process_free_queue(VCHIQ_STATE_T *state)
-+{
-+ VCHIQ_SHARED_STATE_T *local = state->local;
-+ BITSET_T service_found[BITSET_SIZE(VCHIQ_MAX_SERVICES)];
-+ int slot_queue_available;
-+
-+ /* Use a read memory barrier to ensure that any state that may have
-+ ** been modified by another thread is not masked by stale prefetched
-+ ** values. */
-+ rmb();
-+
-+ /* Find slots which have been freed by the other side, and return them
-+ ** to the available queue. */
-+ slot_queue_available = state->slot_queue_available;
-+
-+ while (slot_queue_available != local->slot_queue_recycle) {
-+ unsigned int pos;
-+ int slot_index = local->slot_queue[slot_queue_available++ &
-+ VCHIQ_SLOT_QUEUE_MASK];
-+ char *data = (char *)SLOT_DATA_FROM_INDEX(state, slot_index);
-+ int data_found = 0;
-+
-+ vchiq_log_trace(vchiq_core_log_level, "%d: pfq %d=%x %x %x",
-+ state->id, slot_index, (unsigned int)data,
-+ local->slot_queue_recycle, slot_queue_available);
-+
-+ /* Initialise the bitmask for services which have used this
-+ ** slot */
-+ BITSET_ZERO(service_found);
-+
-+ pos = 0;
-+
-+ while (pos < VCHIQ_SLOT_SIZE) {
-+ VCHIQ_HEADER_T *header =
-+ (VCHIQ_HEADER_T *)(data + pos);
-+ int msgid = header->msgid;
-+ if (VCHIQ_MSG_TYPE(msgid) == VCHIQ_MSG_DATA) {
-+ int port = VCHIQ_MSG_SRCPORT(msgid);
-+ VCHIQ_SERVICE_QUOTA_T *service_quota =
-+ &state->service_quotas[port];
-+ int count;
-+ spin_lock("a_spinlock);
-+ count = service_quota->message_use_count;
-+ if (count > 0)
-+ service_quota->message_use_count =
-+ count - 1;
-+ spin_unlock("a_spinlock);
-+
-+ if (count == service_quota->message_quota)
-+ /* Signal the service that it
-+ ** has dropped below its quota
-+ */
-+ up(&service_quota->quota_event);
-+ else if (count == 0) {
-+ vchiq_log_error(vchiq_core_log_level,
-+ "service %d "
-+ "message_use_count=%d "
-+ "(header %x, msgid %x, "
-+ "header->msgid %x, "
-+ "header->size %x)",
-+ port,
-+ service_quota->
-+ message_use_count,
-+ (unsigned int)header, msgid,
-+ header->msgid,
-+ header->size);
-+ WARN(1, "invalid message use count\n");
-+ }
-+ if (!BITSET_IS_SET(service_found, port)) {
-+ /* Set the found bit for this service */
-+ BITSET_SET(service_found, port);
-+
-+ spin_lock("a_spinlock);
-+ count = service_quota->slot_use_count;
-+ if (count > 0)
-+ service_quota->slot_use_count =
-+ count - 1;
-+ spin_unlock("a_spinlock);
-+
-+ if (count > 0) {
-+ /* Signal the service in case
-+ ** it has dropped below its
-+ ** quota */
-+ up(&service_quota->quota_event);
-+ vchiq_log_trace(
-+ vchiq_core_log_level,
-+ "%d: pfq:%d %x@%x - "
-+ "slot_use->%d",
-+ state->id, port,
-+ header->size,
-+ (unsigned int)header,
-+ count - 1);
-+ } else {
-+ vchiq_log_error(
-+ vchiq_core_log_level,
-+ "service %d "
-+ "slot_use_count"
-+ "=%d (header %x"
-+ ", msgid %x, "
-+ "header->msgid"
-+ " %x, header->"
-+ "size %x)",
-+ port, count,
-+ (unsigned int)header,
-+ msgid,
-+ header->msgid,
-+ header->size);
-+ WARN(1, "bad slot use count\n");
-+ }
-+ }
-+
-+ data_found = 1;
-+ }
-+
-+ pos += calc_stride(header->size);
-+ if (pos > VCHIQ_SLOT_SIZE) {
-+ vchiq_log_error(vchiq_core_log_level,
-+ "pfq - pos %x: header %x, msgid %x, "
-+ "header->msgid %x, header->size %x",
-+ pos, (unsigned int)header, msgid,
-+ header->msgid, header->size);
-+ WARN(1, "invalid slot position\n");
-+ }
-+ }
-+
-+ if (data_found) {
-+ int count;
-+ spin_lock("a_spinlock);
-+ count = state->data_use_count;
-+ if (count > 0)
-+ state->data_use_count =
-+ count - 1;
-+ spin_unlock("a_spinlock);
-+ if (count == state->data_quota)
-+ up(&state->data_quota_event);
-+ }
-+
-+ state->slot_queue_available = slot_queue_available;
-+ up(&state->slot_available_event);
-+ }
-+}
-+
-+/* Called by the slot handler and application threads */
-+static VCHIQ_STATUS_T
-+queue_message(VCHIQ_STATE_T *state, VCHIQ_SERVICE_T *service,
-+ int msgid, const VCHIQ_ELEMENT_T *elements,
-+ int count, int size, int flags)
-+{
-+ VCHIQ_SHARED_STATE_T *local;
-+ VCHIQ_SERVICE_QUOTA_T *service_quota = NULL;
-+ VCHIQ_HEADER_T *header;
-+ int type = VCHIQ_MSG_TYPE(msgid);
-+
-+ unsigned int stride;
-+
-+ local = state->local;
-+
-+ stride = calc_stride(size);
-+
-+ WARN_ON(!(stride <= VCHIQ_SLOT_SIZE));
-+
-+ if (!(flags & QMFLAGS_NO_MUTEX_LOCK) &&
-+ (mutex_lock_interruptible(&state->slot_mutex) != 0))
-+ return VCHIQ_RETRY;
-+
-+ if (type == VCHIQ_MSG_DATA) {
-+ int tx_end_index;
-+
-+ BUG_ON(!service);
-+ BUG_ON((flags & (QMFLAGS_NO_MUTEX_LOCK |
-+ QMFLAGS_NO_MUTEX_UNLOCK)) != 0);
-+
-+ if (service->closing) {
-+ /* The service has been closed */
-+ mutex_unlock(&state->slot_mutex);
-+ return VCHIQ_ERROR;
-+ }
-+
-+ service_quota = &state->service_quotas[service->localport];
-+
-+ spin_lock("a_spinlock);
-+
-+ /* Ensure this service doesn't use more than its quota of
-+ ** messages or slots */
-+ tx_end_index = SLOT_QUEUE_INDEX_FROM_POS(
-+ state->local_tx_pos + stride - 1);
-+
-+ /* Ensure data messages don't use more than their quota of
-+ ** slots */
-+ while ((tx_end_index != state->previous_data_index) &&
-+ (state->data_use_count == state->data_quota)) {
-+ VCHIQ_STATS_INC(state, data_stalls);
-+ spin_unlock("a_spinlock);
-+ mutex_unlock(&state->slot_mutex);
-+
-+ if (down_interruptible(&state->data_quota_event)
-+ != 0)
-+ return VCHIQ_RETRY;
-+
-+ mutex_lock(&state->slot_mutex);
-+ spin_lock("a_spinlock);
-+ tx_end_index = SLOT_QUEUE_INDEX_FROM_POS(
-+ state->local_tx_pos + stride - 1);
-+ if ((tx_end_index == state->previous_data_index) ||
-+ (state->data_use_count < state->data_quota)) {
-+ /* Pass the signal on to other waiters */
-+ up(&state->data_quota_event);
-+ break;
-+ }
-+ }
-+
-+ while ((service_quota->message_use_count ==
-+ service_quota->message_quota) ||
-+ ((tx_end_index != service_quota->previous_tx_index) &&
-+ (service_quota->slot_use_count ==
-+ service_quota->slot_quota))) {
-+ spin_unlock("a_spinlock);
-+ vchiq_log_trace(vchiq_core_log_level,
-+ "%d: qm:%d %s,%x - quota stall "
-+ "(msg %d, slot %d)",
-+ state->id, service->localport,
-+ msg_type_str(type), size,
-+ service_quota->message_use_count,
-+ service_quota->slot_use_count);
-+ VCHIQ_SERVICE_STATS_INC(service, quota_stalls);
-+ mutex_unlock(&state->slot_mutex);
-+ if (down_interruptible(&service_quota->quota_event)
-+ != 0)
-+ return VCHIQ_RETRY;
-+ if (service->closing)
-+ return VCHIQ_ERROR;
-+ if (mutex_lock_interruptible(&state->slot_mutex) != 0)
-+ return VCHIQ_RETRY;
-+ if (service->srvstate != VCHIQ_SRVSTATE_OPEN) {
-+ /* The service has been closed */
-+ mutex_unlock(&state->slot_mutex);
-+ return VCHIQ_ERROR;
-+ }
-+ spin_lock("a_spinlock);
-+ tx_end_index = SLOT_QUEUE_INDEX_FROM_POS(
-+ state->local_tx_pos + stride - 1);
-+ }
-+
-+ spin_unlock("a_spinlock);
-+ }
-+
-+ header = reserve_space(state, stride, flags & QMFLAGS_IS_BLOCKING);
-+
-+ if (!header) {
-+ if (service)
-+ VCHIQ_SERVICE_STATS_INC(service, slot_stalls);
-+ /* In the event of a failure, return the mutex to the
-+ state it was in */
-+ if (!(flags & QMFLAGS_NO_MUTEX_LOCK))
-+ mutex_unlock(&state->slot_mutex);
-+ return VCHIQ_RETRY;
-+ }
-+
-+ if (type == VCHIQ_MSG_DATA) {
-+ int i, pos;
-+ int tx_end_index;
-+ int slot_use_count;
-+
-+ vchiq_log_info(vchiq_core_log_level,
-+ "%d: qm %s@%x,%x (%d->%d)",
-+ state->id,
-+ msg_type_str(VCHIQ_MSG_TYPE(msgid)),
-+ (unsigned int)header, size,
-+ VCHIQ_MSG_SRCPORT(msgid),
-+ VCHIQ_MSG_DSTPORT(msgid));
-+
-+ BUG_ON(!service);
-+ BUG_ON((flags & (QMFLAGS_NO_MUTEX_LOCK |
-+ QMFLAGS_NO_MUTEX_UNLOCK)) != 0);
-+
-+ for (i = 0, pos = 0; i < (unsigned int)count;
-+ pos += elements[i++].size)
-+ if (elements[i].size) {
-+ if (vchiq_copy_from_user
-+ (header->data + pos, elements[i].data,
-+ (size_t) elements[i].size) !=
-+ VCHIQ_SUCCESS) {
-+ mutex_unlock(&state->slot_mutex);
-+ VCHIQ_SERVICE_STATS_INC(service,
-+ error_count);
-+ return VCHIQ_ERROR;
-+ }
-+ if (i == 0) {
-+ if (SRVTRACE_ENABLED(service,
-+ VCHIQ_LOG_INFO))
-+ vchiq_log_dump_mem("Sent", 0,
-+ header->data + pos,
-+ min(64u,
-+ elements[0].size));
-+ }
-+ }
-+
-+ spin_lock("a_spinlock);
-+ service_quota->message_use_count++;
-+
-+ tx_end_index =
-+ SLOT_QUEUE_INDEX_FROM_POS(state->local_tx_pos - 1);
-+
-+ /* If this transmission can't fit in the last slot used by any
-+ ** service, the data_use_count must be increased. */
-+ if (tx_end_index != state->previous_data_index) {
-+ state->previous_data_index = tx_end_index;
-+ state->data_use_count++;
-+ }
-+
-+ /* If this isn't the same slot last used by this service,
-+ ** the service's slot_use_count must be increased. */
-+ if (tx_end_index != service_quota->previous_tx_index) {
-+ service_quota->previous_tx_index = tx_end_index;
-+ slot_use_count = ++service_quota->slot_use_count;
-+ } else {
-+ slot_use_count = 0;
-+ }
-+
-+ spin_unlock("a_spinlock);
-+
-+ if (slot_use_count)
-+ vchiq_log_trace(vchiq_core_log_level,
-+ "%d: qm:%d %s,%x - slot_use->%d (hdr %p)",
-+ state->id, service->localport,
-+ msg_type_str(VCHIQ_MSG_TYPE(msgid)), size,
-+ slot_use_count, header);
-+
-+ VCHIQ_SERVICE_STATS_INC(service, ctrl_tx_count);
-+ VCHIQ_SERVICE_STATS_ADD(service, ctrl_tx_bytes, size);
-+ } else {
-+ vchiq_log_info(vchiq_core_log_level,
-+ "%d: qm %s@%x,%x (%d->%d)", state->id,
-+ msg_type_str(VCHIQ_MSG_TYPE(msgid)),
-+ (unsigned int)header, size,
-+ VCHIQ_MSG_SRCPORT(msgid),
-+ VCHIQ_MSG_DSTPORT(msgid));
-+ if (size != 0) {
-+ WARN_ON(!((count == 1) && (size == elements[0].size)));
-+ memcpy(header->data, elements[0].data,
-+ elements[0].size);
-+ }
-+ VCHIQ_STATS_INC(state, ctrl_tx_count);
-+ }
-+
-+ header->msgid = msgid;
-+ header->size = size;
-+
-+ {
-+ int svc_fourcc;
-+
-+ svc_fourcc = service
-+ ? service->base.fourcc
-+ : VCHIQ_MAKE_FOURCC('?', '?', '?', '?');
-+
-+ vchiq_log_info(SRVTRACE_LEVEL(service),
-+ "Sent Msg %s(%u) to %c%c%c%c s:%u d:%d len:%d",
-+ msg_type_str(VCHIQ_MSG_TYPE(msgid)),
-+ VCHIQ_MSG_TYPE(msgid),
-+ VCHIQ_FOURCC_AS_4CHARS(svc_fourcc),
-+ VCHIQ_MSG_SRCPORT(msgid),
-+ VCHIQ_MSG_DSTPORT(msgid),
-+ size);
-+ }
-+
-+ /* Make sure the new header is visible to the peer. */
-+ wmb();
-+
-+ /* Make the new tx_pos visible to the peer. */
-+ local->tx_pos = state->local_tx_pos;
-+ wmb();
-+
-+ if (service && (type == VCHIQ_MSG_CLOSE))
-+ vchiq_set_service_state(service, VCHIQ_SRVSTATE_CLOSESENT);
-+
-+ if (!(flags & QMFLAGS_NO_MUTEX_UNLOCK))
-+ mutex_unlock(&state->slot_mutex);
-+
-+ remote_event_signal(&state->remote->trigger);
-+
-+ return VCHIQ_SUCCESS;
-+}
-+
-+/* Called by the slot handler and application threads */
-+static VCHIQ_STATUS_T
-+queue_message_sync(VCHIQ_STATE_T *state, VCHIQ_SERVICE_T *service,
-+ int msgid, const VCHIQ_ELEMENT_T *elements,
-+ int count, int size, int is_blocking)
-+{
-+ VCHIQ_SHARED_STATE_T *local;
-+ VCHIQ_HEADER_T *header;
-+
-+ local = state->local;
-+
-+ if ((VCHIQ_MSG_TYPE(msgid) != VCHIQ_MSG_RESUME) &&
-+ (mutex_lock_interruptible(&state->sync_mutex) != 0))
-+ return VCHIQ_RETRY;
-+
-+ remote_event_wait(&local->sync_release);
-+
-+ rmb();
-+
-+ header = (VCHIQ_HEADER_T *)SLOT_DATA_FROM_INDEX(state,
-+ local->slot_sync);
-+
-+ {
-+ int oldmsgid = header->msgid;
-+ if (oldmsgid != VCHIQ_MSGID_PADDING)
-+ vchiq_log_error(vchiq_core_log_level,
-+ "%d: qms - msgid %x, not PADDING",
-+ state->id, oldmsgid);
-+ }
-+
-+ if (service) {
-+ int i, pos;
-+
-+ vchiq_log_info(vchiq_sync_log_level,
-+ "%d: qms %s@%x,%x (%d->%d)", state->id,
-+ msg_type_str(VCHIQ_MSG_TYPE(msgid)),
-+ (unsigned int)header, size,
-+ VCHIQ_MSG_SRCPORT(msgid),
-+ VCHIQ_MSG_DSTPORT(msgid));
-+
-+ for (i = 0, pos = 0; i < (unsigned int)count;
-+ pos += elements[i++].size)
-+ if (elements[i].size) {
-+ if (vchiq_copy_from_user
-+ (header->data + pos, elements[i].data,
-+ (size_t) elements[i].size) !=
-+ VCHIQ_SUCCESS) {
-+ mutex_unlock(&state->sync_mutex);
-+ VCHIQ_SERVICE_STATS_INC(service,
-+ error_count);
-+ return VCHIQ_ERROR;
-+ }
-+ if (i == 0) {
-+ if (vchiq_sync_log_level >=
-+ VCHIQ_LOG_TRACE)
-+ vchiq_log_dump_mem("Sent Sync",
-+ 0, header->data + pos,
-+ min(64u,
-+ elements[0].size));
-+ }
-+ }
-+
-+ VCHIQ_SERVICE_STATS_INC(service, ctrl_tx_count);
-+ VCHIQ_SERVICE_STATS_ADD(service, ctrl_tx_bytes, size);
-+ } else {
-+ vchiq_log_info(vchiq_sync_log_level,
-+ "%d: qms %s@%x,%x (%d->%d)", state->id,
-+ msg_type_str(VCHIQ_MSG_TYPE(msgid)),
-+ (unsigned int)header, size,
-+ VCHIQ_MSG_SRCPORT(msgid),
-+ VCHIQ_MSG_DSTPORT(msgid));
-+ if (size != 0) {
-+ WARN_ON(!((count == 1) && (size == elements[0].size)));
-+ memcpy(header->data, elements[0].data,
-+ elements[0].size);
-+ }
-+ VCHIQ_STATS_INC(state, ctrl_tx_count);
-+ }
-+
-+ header->size = size;
-+ header->msgid = msgid;
-+
-+ if (vchiq_sync_log_level >= VCHIQ_LOG_TRACE) {
-+ int svc_fourcc;
-+
-+ svc_fourcc = service
-+ ? service->base.fourcc
-+ : VCHIQ_MAKE_FOURCC('?', '?', '?', '?');
-+
-+ vchiq_log_trace(vchiq_sync_log_level,
-+ "Sent Sync Msg %s(%u) to %c%c%c%c s:%u d:%d len:%d",
-+ msg_type_str(VCHIQ_MSG_TYPE(msgid)),
-+ VCHIQ_MSG_TYPE(msgid),
-+ VCHIQ_FOURCC_AS_4CHARS(svc_fourcc),
-+ VCHIQ_MSG_SRCPORT(msgid),
-+ VCHIQ_MSG_DSTPORT(msgid),
-+ size);
-+ }
-+
-+ /* Make sure the new header is visible to the peer. */
-+ wmb();
-+
-+ remote_event_signal(&state->remote->sync_trigger);
-+
-+ if (VCHIQ_MSG_TYPE(msgid) != VCHIQ_MSG_PAUSE)
-+ mutex_unlock(&state->sync_mutex);
-+
-+ return VCHIQ_SUCCESS;
-+}
-+
-+static inline void
-+claim_slot(VCHIQ_SLOT_INFO_T *slot)
-+{
-+ slot->use_count++;
-+}
-+
-+static void
-+release_slot(VCHIQ_STATE_T *state, VCHIQ_SLOT_INFO_T *slot_info,
-+ VCHIQ_HEADER_T *header, VCHIQ_SERVICE_T *service)
-+{
-+ int release_count;
-+
-+ mutex_lock(&state->recycle_mutex);
-+
-+ if (header) {
-+ int msgid = header->msgid;
-+ if (((msgid & VCHIQ_MSGID_CLAIMED) == 0) ||
-+ (service && service->closing)) {
-+ mutex_unlock(&state->recycle_mutex);
-+ return;
-+ }
-+
-+ /* Rewrite the message header to prevent a double
-+ ** release */
-+ header->msgid = msgid & ~VCHIQ_MSGID_CLAIMED;
-+ }
-+
-+ release_count = slot_info->release_count;
-+ slot_info->release_count = ++release_count;
-+
-+ if (release_count == slot_info->use_count) {
-+ int slot_queue_recycle;
-+ /* Add to the freed queue */
-+
-+ /* A read barrier is necessary here to prevent speculative
-+ ** fetches of remote->slot_queue_recycle from overtaking the
-+ ** mutex. */
-+ rmb();
-+
-+ slot_queue_recycle = state->remote->slot_queue_recycle;
-+ state->remote->slot_queue[slot_queue_recycle &
-+ VCHIQ_SLOT_QUEUE_MASK] =
-+ SLOT_INDEX_FROM_INFO(state, slot_info);
-+ state->remote->slot_queue_recycle = slot_queue_recycle + 1;
-+ vchiq_log_info(vchiq_core_log_level,
-+ "%d: release_slot %d - recycle->%x",
-+ state->id, SLOT_INDEX_FROM_INFO(state, slot_info),
-+ state->remote->slot_queue_recycle);
-+
-+ /* A write barrier is necessary, but remote_event_signal
-+ ** contains one. */
-+ remote_event_signal(&state->remote->recycle);
-+ }
-+
-+ mutex_unlock(&state->recycle_mutex);
-+}
-+
-+/* Called by the slot handler - don't hold the bulk mutex */
-+static VCHIQ_STATUS_T
-+notify_bulks(VCHIQ_SERVICE_T *service, VCHIQ_BULK_QUEUE_T *queue,
-+ int retry_poll)
-+{
-+ VCHIQ_STATUS_T status = VCHIQ_SUCCESS;
-+
-+ vchiq_log_trace(vchiq_core_log_level,
-+ "%d: nb:%d %cx - p=%x rn=%x r=%x",
-+ service->state->id, service->localport,
-+ (queue == &service->bulk_tx) ? 't' : 'r',
-+ queue->process, queue->remote_notify, queue->remove);
-+
-+ if (service->state->is_master) {
-+ while (queue->remote_notify != queue->process) {
-+ VCHIQ_BULK_T *bulk =
-+ &queue->bulks[BULK_INDEX(queue->remote_notify)];
-+ int msgtype = (bulk->dir == VCHIQ_BULK_TRANSMIT) ?
-+ VCHIQ_MSG_BULK_RX_DONE : VCHIQ_MSG_BULK_TX_DONE;
-+ int msgid = VCHIQ_MAKE_MSG(msgtype, service->localport,
-+ service->remoteport);
-+ VCHIQ_ELEMENT_T element = { &bulk->actual, 4 };
-+ /* Only reply to non-dummy bulk requests */
-+ if (bulk->remote_data) {
-+ status = queue_message(service->state, NULL,
-+ msgid, &element, 1, 4, 0);
-+ if (status != VCHIQ_SUCCESS)
-+ break;
-+ }
-+ queue->remote_notify++;
-+ }
-+ } else {
-+ queue->remote_notify = queue->process;
-+ }
-+
-+ if (status == VCHIQ_SUCCESS) {
-+ while (queue->remove != queue->remote_notify) {
-+ VCHIQ_BULK_T *bulk =
-+ &queue->bulks[BULK_INDEX(queue->remove)];
-+
-+ /* Only generate callbacks for non-dummy bulk
-+ ** requests, and non-terminated services */
-+ if (bulk->data && service->instance) {
-+ if (bulk->actual != VCHIQ_BULK_ACTUAL_ABORTED) {
-+ if (bulk->dir == VCHIQ_BULK_TRANSMIT) {
-+ VCHIQ_SERVICE_STATS_INC(service,
-+ bulk_tx_count);
-+ VCHIQ_SERVICE_STATS_ADD(service,
-+ bulk_tx_bytes,
-+ bulk->actual);
-+ } else {
-+ VCHIQ_SERVICE_STATS_INC(service,
-+ bulk_rx_count);
-+ VCHIQ_SERVICE_STATS_ADD(service,
-+ bulk_rx_bytes,
-+ bulk->actual);
-+ }
-+ } else {
-+ VCHIQ_SERVICE_STATS_INC(service,
-+ bulk_aborted_count);
-+ }
-+ if (bulk->mode == VCHIQ_BULK_MODE_BLOCKING) {
-+ struct bulk_waiter *waiter;
-+ spin_lock(&bulk_waiter_spinlock);
-+ waiter = bulk->userdata;
-+ if (waiter) {
-+ waiter->actual = bulk->actual;
-+ up(&waiter->event);
-+ }
-+ spin_unlock(&bulk_waiter_spinlock);
-+ } else if (bulk->mode ==
-+ VCHIQ_BULK_MODE_CALLBACK) {
-+ VCHIQ_REASON_T reason = (bulk->dir ==
-+ VCHIQ_BULK_TRANSMIT) ?
-+ ((bulk->actual ==
-+ VCHIQ_BULK_ACTUAL_ABORTED) ?
-+ VCHIQ_BULK_TRANSMIT_ABORTED :
-+ VCHIQ_BULK_TRANSMIT_DONE) :
-+ ((bulk->actual ==
-+ VCHIQ_BULK_ACTUAL_ABORTED) ?
-+ VCHIQ_BULK_RECEIVE_ABORTED :
-+ VCHIQ_BULK_RECEIVE_DONE);
-+ status = make_service_callback(service,
-+ reason, NULL, bulk->userdata);
-+ if (status == VCHIQ_RETRY)
-+ break;
-+ }
-+ }
-+
-+ queue->remove++;
-+ up(&service->bulk_remove_event);
-+ }
-+ if (!retry_poll)
-+ status = VCHIQ_SUCCESS;
-+ }
-+
-+ if (status == VCHIQ_RETRY)
-+ request_poll(service->state, service,
-+ (queue == &service->bulk_tx) ?
-+ VCHIQ_POLL_TXNOTIFY : VCHIQ_POLL_RXNOTIFY);
-+
-+ return status;
-+}
-+
-+/* Called by the slot handler thread */
-+static void
-+poll_services(VCHIQ_STATE_T *state)
-+{
-+ int group, i;
-+
-+ for (group = 0; group < BITSET_SIZE(state->unused_service); group++) {
-+ uint32_t flags;
-+ flags = atomic_xchg(&state->poll_services[group], 0);
-+ for (i = 0; flags; i++) {
-+ if (flags & (1 << i)) {
-+ VCHIQ_SERVICE_T *service =
-+ find_service_by_port(state,
-+ (group<<5) + i);
-+ uint32_t service_flags;
-+ flags &= ~(1 << i);
-+ if (!service)
-+ continue;
-+ service_flags =
-+ atomic_xchg(&service->poll_flags, 0);
-+ if (service_flags &
-+ (1 << VCHIQ_POLL_REMOVE)) {
-+ vchiq_log_info(vchiq_core_log_level,
-+ "%d: ps - remove %d<->%d",
-+ state->id, service->localport,
-+ service->remoteport);
-+
-+ /* Make it look like a client, because
-+ it must be removed and not left in
-+ the LISTENING state. */
-+ service->public_fourcc =
-+ VCHIQ_FOURCC_INVALID;
-+
-+ if (vchiq_close_service_internal(
-+ service, 0/*!close_recvd*/) !=
-+ VCHIQ_SUCCESS)
-+ request_poll(state, service,
-+ VCHIQ_POLL_REMOVE);
-+ } else if (service_flags &
-+ (1 << VCHIQ_POLL_TERMINATE)) {
-+ vchiq_log_info(vchiq_core_log_level,
-+ "%d: ps - terminate %d<->%d",
-+ state->id, service->localport,
-+ service->remoteport);
-+ if (vchiq_close_service_internal(
-+ service, 0/*!close_recvd*/) !=
-+ VCHIQ_SUCCESS)
-+ request_poll(state, service,
-+ VCHIQ_POLL_TERMINATE);
-+ }
-+ if (service_flags & (1 << VCHIQ_POLL_TXNOTIFY))
-+ notify_bulks(service,
-+ &service->bulk_tx,
-+ 1/*retry_poll*/);
-+ if (service_flags & (1 << VCHIQ_POLL_RXNOTIFY))
-+ notify_bulks(service,
-+ &service->bulk_rx,
-+ 1/*retry_poll*/);
-+ unlock_service(service);
-+ }
-+ }
-+ }
-+}
-+
-+/* Called by the slot handler or application threads, holding the bulk mutex. */
-+static int
-+resolve_bulks(VCHIQ_SERVICE_T *service, VCHIQ_BULK_QUEUE_T *queue)
-+{
-+ VCHIQ_STATE_T *state = service->state;
-+ int resolved = 0;
-+ int rc;
-+
-+ while ((queue->process != queue->local_insert) &&
-+ (queue->process != queue->remote_insert)) {
-+ VCHIQ_BULK_T *bulk = &queue->bulks[BULK_INDEX(queue->process)];
-+
-+ vchiq_log_trace(vchiq_core_log_level,
-+ "%d: rb:%d %cx - li=%x ri=%x p=%x",
-+ state->id, service->localport,
-+ (queue == &service->bulk_tx) ? 't' : 'r',
-+ queue->local_insert, queue->remote_insert,
-+ queue->process);
-+
-+ WARN_ON(!((int)(queue->local_insert - queue->process) > 0));
-+ WARN_ON(!((int)(queue->remote_insert - queue->process) > 0));
-+
-+ rc = mutex_lock_interruptible(&state->bulk_transfer_mutex);
-+ if (rc != 0)
-+ break;
-+
-+ vchiq_transfer_bulk(bulk);
-+ mutex_unlock(&state->bulk_transfer_mutex);
-+
-+ if (SRVTRACE_ENABLED(service, VCHIQ_LOG_INFO)) {
-+ const char *header = (queue == &service->bulk_tx) ?
-+ "Send Bulk to" : "Recv Bulk from";
-+ if (bulk->actual != VCHIQ_BULK_ACTUAL_ABORTED)
-+ vchiq_log_info(SRVTRACE_LEVEL(service),
-+ "%s %c%c%c%c d:%d len:%d %x<->%x",
-+ header,
-+ VCHIQ_FOURCC_AS_4CHARS(
-+ service->base.fourcc),
-+ service->remoteport,
-+ bulk->size,
-+ (unsigned int)bulk->data,
-+ (unsigned int)bulk->remote_data);
-+ else
-+ vchiq_log_info(SRVTRACE_LEVEL(service),
-+ "%s %c%c%c%c d:%d ABORTED - tx len:%d,"
-+ " rx len:%d %x<->%x",
-+ header,
-+ VCHIQ_FOURCC_AS_4CHARS(
-+ service->base.fourcc),
-+ service->remoteport,
-+ bulk->size,
-+ bulk->remote_size,
-+ (unsigned int)bulk->data,
-+ (unsigned int)bulk->remote_data);
-+ }
-+
-+ vchiq_complete_bulk(bulk);
-+ queue->process++;
-+ resolved++;
-+ }
-+ return resolved;
-+}
-+
-+/* Called with the bulk_mutex held */
-+static void
-+abort_outstanding_bulks(VCHIQ_SERVICE_T *service, VCHIQ_BULK_QUEUE_T *queue)
-+{
-+ int is_tx = (queue == &service->bulk_tx);
-+ vchiq_log_trace(vchiq_core_log_level,
-+ "%d: aob:%d %cx - li=%x ri=%x p=%x",
-+ service->state->id, service->localport, is_tx ? 't' : 'r',
-+ queue->local_insert, queue->remote_insert, queue->process);
-+
-+ WARN_ON(!((int)(queue->local_insert - queue->process) >= 0));
-+ WARN_ON(!((int)(queue->remote_insert - queue->process) >= 0));
-+
-+ while ((queue->process != queue->local_insert) ||
-+ (queue->process != queue->remote_insert)) {
-+ VCHIQ_BULK_T *bulk = &queue->bulks[BULK_INDEX(queue->process)];
-+
-+ if (queue->process == queue->remote_insert) {
-+ /* fabricate a matching dummy bulk */
-+ bulk->remote_data = NULL;
-+ bulk->remote_size = 0;
-+ queue->remote_insert++;
-+ }
-+
-+ if (queue->process != queue->local_insert) {
-+ vchiq_complete_bulk(bulk);
-+
-+ vchiq_log_info(SRVTRACE_LEVEL(service),
-+ "%s %c%c%c%c d:%d ABORTED - tx len:%d, "
-+ "rx len:%d",
-+ is_tx ? "Send Bulk to" : "Recv Bulk from",
-+ VCHIQ_FOURCC_AS_4CHARS(service->base.fourcc),
-+ service->remoteport,
-+ bulk->size,
-+ bulk->remote_size);
-+ } else {
-+ /* fabricate a matching dummy bulk */
-+ bulk->data = NULL;
-+ bulk->size = 0;
-+ bulk->actual = VCHIQ_BULK_ACTUAL_ABORTED;
-+ bulk->dir = is_tx ? VCHIQ_BULK_TRANSMIT :
-+ VCHIQ_BULK_RECEIVE;
-+ queue->local_insert++;
-+ }
-+
-+ queue->process++;
-+ }
-+}
-+
-+/* Called from the slot handler thread */
-+static void
-+pause_bulks(VCHIQ_STATE_T *state)
-+{
-+ if (unlikely(atomic_inc_return(&pause_bulks_count) != 1)) {
-+ WARN_ON_ONCE(1);
-+ atomic_set(&pause_bulks_count, 1);
-+ return;
-+ }
-+
-+ /* Block bulk transfers from all services */
-+ mutex_lock(&state->bulk_transfer_mutex);
-+}
-+
-+/* Called from the slot handler thread */
-+static void
-+resume_bulks(VCHIQ_STATE_T *state)
-+{
-+ int i;
-+ if (unlikely(atomic_dec_return(&pause_bulks_count) != 0)) {
-+ WARN_ON_ONCE(1);
-+ atomic_set(&pause_bulks_count, 0);
-+ return;
-+ }
-+
-+ /* Allow bulk transfers from all services */
-+ mutex_unlock(&state->bulk_transfer_mutex);
-+
-+ if (state->deferred_bulks == 0)
-+ return;
-+
-+ /* Deal with any bulks which had to be deferred due to being in
-+ * paused state. Don't try to match up to number of deferred bulks
-+ * in case we've had something come and close the service in the
-+ * interim - just process all bulk queues for all services */
-+ vchiq_log_info(vchiq_core_log_level, "%s: processing %d deferred bulks",
-+ __func__, state->deferred_bulks);
-+
-+ for (i = 0; i < state->unused_service; i++) {
-+ VCHIQ_SERVICE_T *service = state->services[i];
-+ int resolved_rx = 0;
-+ int resolved_tx = 0;
-+ if (!service || (service->srvstate != VCHIQ_SRVSTATE_OPEN))
-+ continue;
-+
-+ mutex_lock(&service->bulk_mutex);
-+ resolved_rx = resolve_bulks(service, &service->bulk_rx);
-+ resolved_tx = resolve_bulks(service, &service->bulk_tx);
-+ mutex_unlock(&service->bulk_mutex);
-+ if (resolved_rx)
-+ notify_bulks(service, &service->bulk_rx, 1);
-+ if (resolved_tx)
-+ notify_bulks(service, &service->bulk_tx, 1);
-+ }
-+ state->deferred_bulks = 0;
-+}
-+
-+static int
-+parse_open(VCHIQ_STATE_T *state, VCHIQ_HEADER_T *header)
-+{
-+ VCHIQ_SERVICE_T *service = NULL;
-+ int msgid, size;
-+ int type;
-+ unsigned int localport, remoteport;
-+
-+ msgid = header->msgid;
-+ size = header->size;
-+ type = VCHIQ_MSG_TYPE(msgid);
-+ localport = VCHIQ_MSG_DSTPORT(msgid);
-+ remoteport = VCHIQ_MSG_SRCPORT(msgid);
-+ if (size >= sizeof(struct vchiq_open_payload)) {
-+ const struct vchiq_open_payload *payload =
-+ (struct vchiq_open_payload *)header->data;
-+ unsigned int fourcc;
-+
-+ fourcc = payload->fourcc;
-+ vchiq_log_info(vchiq_core_log_level,
-+ "%d: prs OPEN@%x (%d->'%c%c%c%c')",
-+ state->id, (unsigned int)header,
-+ localport,
-+ VCHIQ_FOURCC_AS_4CHARS(fourcc));
-+
-+ service = get_listening_service(state, fourcc);
-+
-+ if (service) {
-+ /* A matching service exists */
-+ short version = payload->version;
-+ short version_min = payload->version_min;
-+ if ((service->version < version_min) ||
-+ (version < service->version_min)) {
-+ /* Version mismatch */
-+ vchiq_loud_error_header();
-+ vchiq_loud_error("%d: service %d (%c%c%c%c) "
-+ "version mismatch - local (%d, min %d)"
-+ " vs. remote (%d, min %d)",
-+ state->id, service->localport,
-+ VCHIQ_FOURCC_AS_4CHARS(fourcc),
-+ service->version, service->version_min,
-+ version, version_min);
-+ vchiq_loud_error_footer();
-+ unlock_service(service);
-+ service = NULL;
-+ goto fail_open;
-+ }
-+ service->peer_version = version;
-+
-+ if (service->srvstate == VCHIQ_SRVSTATE_LISTENING) {
-+ struct vchiq_openack_payload ack_payload = {
-+ service->version
-+ };
-+ VCHIQ_ELEMENT_T body = {
-+ &ack_payload,
-+ sizeof(ack_payload)
-+ };
-+
-+ if (state->version_common <
-+ VCHIQ_VERSION_SYNCHRONOUS_MODE)
-+ service->sync = 0;
-+
-+ /* Acknowledge the OPEN */
-+ if (service->sync &&
-+ (state->version_common >=
-+ VCHIQ_VERSION_SYNCHRONOUS_MODE)) {
-+ if (queue_message_sync(state, NULL,
-+ VCHIQ_MAKE_MSG(
-+ VCHIQ_MSG_OPENACK,
-+ service->localport,
-+ remoteport),
-+ &body, 1, sizeof(ack_payload),
-+ 0) == VCHIQ_RETRY)
-+ goto bail_not_ready;
-+ } else {
-+ if (queue_message(state, NULL,
-+ VCHIQ_MAKE_MSG(
-+ VCHIQ_MSG_OPENACK,
-+ service->localport,
-+ remoteport),
-+ &body, 1, sizeof(ack_payload),
-+ 0) == VCHIQ_RETRY)
-+ goto bail_not_ready;
-+ }
-+
-+ /* The service is now open */
-+ vchiq_set_service_state(service,
-+ service->sync ? VCHIQ_SRVSTATE_OPENSYNC
-+ : VCHIQ_SRVSTATE_OPEN);
-+ }
-+
-+ service->remoteport = remoteport;
-+ service->client_id = ((int *)header->data)[1];
-+ if (make_service_callback(service, VCHIQ_SERVICE_OPENED,
-+ NULL, NULL) == VCHIQ_RETRY) {
-+ /* Bail out if not ready */
-+ service->remoteport = VCHIQ_PORT_FREE;
-+ goto bail_not_ready;
-+ }
-+
-+ /* Success - the message has been dealt with */
-+ unlock_service(service);
-+ return 1;
-+ }
-+ }
-+
-+fail_open:
-+ /* No available service, or an invalid request - send a CLOSE */
-+ if (queue_message(state, NULL,
-+ VCHIQ_MAKE_MSG(VCHIQ_MSG_CLOSE, 0, VCHIQ_MSG_SRCPORT(msgid)),
-+ NULL, 0, 0, 0) == VCHIQ_RETRY)
-+ goto bail_not_ready;
-+
-+ return 1;
-+
-+bail_not_ready:
-+ if (service)
-+ unlock_service(service);
-+
-+ return 0;
-+}
-+
-+/* Called by the slot handler thread */
-+static void
-+parse_rx_slots(VCHIQ_STATE_T *state)
-+{
-+ VCHIQ_SHARED_STATE_T *remote = state->remote;
-+ VCHIQ_SERVICE_T *service = NULL;
-+ int tx_pos;
-+ DEBUG_INITIALISE(state->local)
-+
-+ tx_pos = remote->tx_pos;
-+
-+ while (state->rx_pos != tx_pos) {
-+ VCHIQ_HEADER_T *header;
-+ int msgid, size;
-+ int type;
-+ unsigned int localport, remoteport;
-+
-+ DEBUG_TRACE(PARSE_LINE);
-+ if (!state->rx_data) {
-+ int rx_index;
-+ WARN_ON(!((state->rx_pos & VCHIQ_SLOT_MASK) == 0));
-+ rx_index = remote->slot_queue[
-+ SLOT_QUEUE_INDEX_FROM_POS(state->rx_pos) &
-+ VCHIQ_SLOT_QUEUE_MASK];
-+ state->rx_data = (char *)SLOT_DATA_FROM_INDEX(state,
-+ rx_index);
-+ state->rx_info = SLOT_INFO_FROM_INDEX(state, rx_index);
-+
-+ /* Initialise use_count to one, and increment
-+ ** release_count at the end of the slot to avoid
-+ ** releasing the slot prematurely. */
-+ state->rx_info->use_count = 1;
-+ state->rx_info->release_count = 0;
-+ }
-+
-+ header = (VCHIQ_HEADER_T *)(state->rx_data +
-+ (state->rx_pos & VCHIQ_SLOT_MASK));
-+ DEBUG_VALUE(PARSE_HEADER, (int)header);
-+ msgid = header->msgid;
-+ DEBUG_VALUE(PARSE_MSGID, msgid);
-+ size = header->size;
-+ type = VCHIQ_MSG_TYPE(msgid);
-+ localport = VCHIQ_MSG_DSTPORT(msgid);
-+ remoteport = VCHIQ_MSG_SRCPORT(msgid);
-+
-+ if (type != VCHIQ_MSG_DATA)
-+ VCHIQ_STATS_INC(state, ctrl_rx_count);
-+
-+ switch (type) {
-+ case VCHIQ_MSG_OPENACK:
-+ case VCHIQ_MSG_CLOSE:
-+ case VCHIQ_MSG_DATA:
-+ case VCHIQ_MSG_BULK_RX:
-+ case VCHIQ_MSG_BULK_TX:
-+ case VCHIQ_MSG_BULK_RX_DONE:
-+ case VCHIQ_MSG_BULK_TX_DONE:
-+ service = find_service_by_port(state, localport);
-+ if ((!service ||
-+ ((service->remoteport != remoteport) &&
-+ (service->remoteport != VCHIQ_PORT_FREE))) &&
-+ (localport == 0) &&
-+ (type == VCHIQ_MSG_CLOSE)) {
-+ /* This could be a CLOSE from a client which
-+ hadn't yet received the OPENACK - look for
-+ the connected service */
-+ if (service)
-+ unlock_service(service);
-+ service = get_connected_service(state,
-+ remoteport);
-+ if (service)
-+ vchiq_log_warning(vchiq_core_log_level,
-+ "%d: prs %s@%x (%d->%d) - "
-+ "found connected service %d",
-+ state->id, msg_type_str(type),
-+ (unsigned int)header,
-+ remoteport, localport,
-+ service->localport);
-+ }
-+
-+ if (!service) {
-+ vchiq_log_error(vchiq_core_log_level,
-+ "%d: prs %s@%x (%d->%d) - "
-+ "invalid/closed service %d",
-+ state->id, msg_type_str(type),
-+ (unsigned int)header,
-+ remoteport, localport, localport);
-+ goto skip_message;
-+ }
-+ break;
-+ default:
-+ break;
-+ }
-+
-+ if (SRVTRACE_ENABLED(service, VCHIQ_LOG_INFO)) {
-+ int svc_fourcc;
-+
-+ svc_fourcc = service
-+ ? service->base.fourcc
-+ : VCHIQ_MAKE_FOURCC('?', '?', '?', '?');
-+ vchiq_log_info(SRVTRACE_LEVEL(service),
-+ "Rcvd Msg %s(%u) from %c%c%c%c s:%d d:%d "
-+ "len:%d",
-+ msg_type_str(type), type,
-+ VCHIQ_FOURCC_AS_4CHARS(svc_fourcc),
-+ remoteport, localport, size);
-+ if (size > 0)
-+ vchiq_log_dump_mem("Rcvd", 0, header->data,
-+ min(64, size));
-+ }
-+
-+ if (((unsigned int)header & VCHIQ_SLOT_MASK) + calc_stride(size)
-+ > VCHIQ_SLOT_SIZE) {
-+ vchiq_log_error(vchiq_core_log_level,
-+ "header %x (msgid %x) - size %x too big for "
-+ "slot",
-+ (unsigned int)header, (unsigned int)msgid,
-+ (unsigned int)size);
-+ WARN(1, "oversized for slot\n");
-+ }
-+
-+ switch (type) {
-+ case VCHIQ_MSG_OPEN:
-+ WARN_ON(!(VCHIQ_MSG_DSTPORT(msgid) == 0));
-+ if (!parse_open(state, header))
-+ goto bail_not_ready;
-+ break;
-+ case VCHIQ_MSG_OPENACK:
-+ if (size >= sizeof(struct vchiq_openack_payload)) {
-+ const struct vchiq_openack_payload *payload =
-+ (struct vchiq_openack_payload *)
-+ header->data;
-+ service->peer_version = payload->version;
-+ }
-+ vchiq_log_info(vchiq_core_log_level,
-+ "%d: prs OPENACK@%x,%x (%d->%d) v:%d",
-+ state->id, (unsigned int)header, size,
-+ remoteport, localport, service->peer_version);
-+ if (service->srvstate ==
-+ VCHIQ_SRVSTATE_OPENING) {
-+ service->remoteport = remoteport;
-+ vchiq_set_service_state(service,
-+ VCHIQ_SRVSTATE_OPEN);
-+ up(&service->remove_event);
-+ } else
-+ vchiq_log_error(vchiq_core_log_level,
-+ "OPENACK received in state %s",
-+ srvstate_names[service->srvstate]);
-+ break;
-+ case VCHIQ_MSG_CLOSE:
-+ WARN_ON(size != 0); /* There should be no data */
-+
-+ vchiq_log_info(vchiq_core_log_level,
-+ "%d: prs CLOSE@%x (%d->%d)",
-+ state->id, (unsigned int)header,
-+ remoteport, localport);
-+
-+ mark_service_closing_internal(service, 1);
-+
-+ if (vchiq_close_service_internal(service,
-+ 1/*close_recvd*/) == VCHIQ_RETRY)
-+ goto bail_not_ready;
-+
-+ vchiq_log_info(vchiq_core_log_level,
-+ "Close Service %c%c%c%c s:%u d:%d",
-+ VCHIQ_FOURCC_AS_4CHARS(service->base.fourcc),
-+ service->localport,
-+ service->remoteport);
-+ break;
-+ case VCHIQ_MSG_DATA:
-+ vchiq_log_info(vchiq_core_log_level,
-+ "%d: prs DATA@%x,%x (%d->%d)",
-+ state->id, (unsigned int)header, size,
-+ remoteport, localport);
-+
-+ if ((service->remoteport == remoteport)
-+ && (service->srvstate ==
-+ VCHIQ_SRVSTATE_OPEN)) {
-+ header->msgid = msgid | VCHIQ_MSGID_CLAIMED;
-+ claim_slot(state->rx_info);
-+ DEBUG_TRACE(PARSE_LINE);
-+ if (make_service_callback(service,
-+ VCHIQ_MESSAGE_AVAILABLE, header,
-+ NULL) == VCHIQ_RETRY) {
-+ DEBUG_TRACE(PARSE_LINE);
-+ goto bail_not_ready;
-+ }
-+ VCHIQ_SERVICE_STATS_INC(service, ctrl_rx_count);
-+ VCHIQ_SERVICE_STATS_ADD(service, ctrl_rx_bytes,
-+ size);
-+ } else {
-+ VCHIQ_STATS_INC(state, error_count);
-+ }
-+ break;
-+ case VCHIQ_MSG_CONNECT:
-+ vchiq_log_info(vchiq_core_log_level,
-+ "%d: prs CONNECT@%x",
-+ state->id, (unsigned int)header);
-+ state->version_common = ((VCHIQ_SLOT_ZERO_T *)
-+ state->slot_data)->version;
-+ up(&state->connect);
-+ break;
-+ case VCHIQ_MSG_BULK_RX:
-+ case VCHIQ_MSG_BULK_TX: {
-+ VCHIQ_BULK_QUEUE_T *queue;
-+ WARN_ON(!state->is_master);
-+ queue = (type == VCHIQ_MSG_BULK_RX) ?
-+ &service->bulk_tx : &service->bulk_rx;
-+ if ((service->remoteport == remoteport)
-+ && (service->srvstate ==
-+ VCHIQ_SRVSTATE_OPEN)) {
-+ VCHIQ_BULK_T *bulk;
-+ int resolved = 0;
-+
-+ DEBUG_TRACE(PARSE_LINE);
-+ if (mutex_lock_interruptible(
-+ &service->bulk_mutex) != 0) {
-+ DEBUG_TRACE(PARSE_LINE);
-+ goto bail_not_ready;
-+ }
-+
-+ WARN_ON(!(queue->remote_insert < queue->remove +
-+ VCHIQ_NUM_SERVICE_BULKS));
-+ bulk = &queue->bulks[
-+ BULK_INDEX(queue->remote_insert)];
-+ bulk->remote_data =
-+ (void *)((int *)header->data)[0];
-+ bulk->remote_size = ((int *)header->data)[1];
-+ wmb();
-+
-+ vchiq_log_info(vchiq_core_log_level,
-+ "%d: prs %s@%x (%d->%d) %x@%x",
-+ state->id, msg_type_str(type),
-+ (unsigned int)header,
-+ remoteport, localport,
-+ bulk->remote_size,
-+ (unsigned int)bulk->remote_data);
-+
-+ queue->remote_insert++;
-+
-+ if (atomic_read(&pause_bulks_count)) {
-+ state->deferred_bulks++;
-+ vchiq_log_info(vchiq_core_log_level,
-+ "%s: deferring bulk (%d)",
-+ __func__,
-+ state->deferred_bulks);
-+ if (state->conn_state !=
-+ VCHIQ_CONNSTATE_PAUSE_SENT)
-+ vchiq_log_error(
-+ vchiq_core_log_level,
-+ "%s: bulks paused in "
-+ "unexpected state %s",
-+ __func__,
-+ conn_state_names[
-+ state->conn_state]);
-+ } else if (state->conn_state ==
-+ VCHIQ_CONNSTATE_CONNECTED) {
-+ DEBUG_TRACE(PARSE_LINE);
-+ resolved = resolve_bulks(service,
-+ queue);
-+ }
-+
-+ mutex_unlock(&service->bulk_mutex);
-+ if (resolved)
-+ notify_bulks(service, queue,
-+ 1/*retry_poll*/);
-+ }
-+ } break;
-+ case VCHIQ_MSG_BULK_RX_DONE:
-+ case VCHIQ_MSG_BULK_TX_DONE:
-+ WARN_ON(state->is_master);
-+ if ((service->remoteport == remoteport)
-+ && (service->srvstate !=
-+ VCHIQ_SRVSTATE_FREE)) {
-+ VCHIQ_BULK_QUEUE_T *queue;
-+ VCHIQ_BULK_T *bulk;
-+
-+ queue = (type == VCHIQ_MSG_BULK_RX_DONE) ?
-+ &service->bulk_rx : &service->bulk_tx;
-+
-+ DEBUG_TRACE(PARSE_LINE);
-+ if (mutex_lock_interruptible(
-+ &service->bulk_mutex) != 0) {
-+ DEBUG_TRACE(PARSE_LINE);
-+ goto bail_not_ready;
-+ }
-+ if ((int)(queue->remote_insert -
-+ queue->local_insert) >= 0) {
-+ vchiq_log_error(vchiq_core_log_level,
-+ "%d: prs %s@%x (%d->%d) "
-+ "unexpected (ri=%d,li=%d)",
-+ state->id, msg_type_str(type),
-+ (unsigned int)header,
-+ remoteport, localport,
-+ queue->remote_insert,
-+ queue->local_insert);
-+ mutex_unlock(&service->bulk_mutex);
-+ break;
-+ }
-+
-+ BUG_ON(queue->process == queue->local_insert);
-+ BUG_ON(queue->process != queue->remote_insert);
-+
-+ bulk = &queue->bulks[
-+ BULK_INDEX(queue->remote_insert)];
-+ bulk->actual = *(int *)header->data;
-+ queue->remote_insert++;
-+
-+ vchiq_log_info(vchiq_core_log_level,
-+ "%d: prs %s@%x (%d->%d) %x@%x",
-+ state->id, msg_type_str(type),
-+ (unsigned int)header,
-+ remoteport, localport,
-+ bulk->actual, (unsigned int)bulk->data);
-+
-+ vchiq_log_trace(vchiq_core_log_level,
-+ "%d: prs:%d %cx li=%x ri=%x p=%x",
-+ state->id, localport,
-+ (type == VCHIQ_MSG_BULK_RX_DONE) ?
-+ 'r' : 't',
-+ queue->local_insert,
-+ queue->remote_insert, queue->process);
-+
-+ DEBUG_TRACE(PARSE_LINE);
-+ WARN_ON(queue->process == queue->local_insert);
-+ vchiq_complete_bulk(bulk);
-+ queue->process++;
-+ mutex_unlock(&service->bulk_mutex);
-+ DEBUG_TRACE(PARSE_LINE);
-+ notify_bulks(service, queue, 1/*retry_poll*/);
-+ DEBUG_TRACE(PARSE_LINE);
-+ }
-+ break;
-+ case VCHIQ_MSG_PADDING:
-+ vchiq_log_trace(vchiq_core_log_level,
-+ "%d: prs PADDING@%x,%x",
-+ state->id, (unsigned int)header, size);
-+ break;
-+ case VCHIQ_MSG_PAUSE:
-+ /* If initiated, signal the application thread */
-+ vchiq_log_trace(vchiq_core_log_level,
-+ "%d: prs PAUSE@%x,%x",
-+ state->id, (unsigned int)header, size);
-+ if (state->conn_state == VCHIQ_CONNSTATE_PAUSED) {
-+ vchiq_log_error(vchiq_core_log_level,
-+ "%d: PAUSE received in state PAUSED",
-+ state->id);
-+ break;
-+ }
-+ if (state->conn_state != VCHIQ_CONNSTATE_PAUSE_SENT) {
-+ /* Send a PAUSE in response */
-+ if (queue_message(state, NULL,
-+ VCHIQ_MAKE_MSG(VCHIQ_MSG_PAUSE, 0, 0),
-+ NULL, 0, 0, QMFLAGS_NO_MUTEX_UNLOCK)
-+ == VCHIQ_RETRY)
-+ goto bail_not_ready;
-+ if (state->is_master)
-+ pause_bulks(state);
-+ }
-+ /* At this point slot_mutex is held */
-+ vchiq_set_conn_state(state, VCHIQ_CONNSTATE_PAUSED);
-+ vchiq_platform_paused(state);
-+ break;
-+ case VCHIQ_MSG_RESUME:
-+ vchiq_log_trace(vchiq_core_log_level,
-+ "%d: prs RESUME@%x,%x",
-+ state->id, (unsigned int)header, size);
-+ /* Release the slot mutex */
-+ mutex_unlock(&state->slot_mutex);
-+ if (state->is_master)
-+ resume_bulks(state);
-+ vchiq_set_conn_state(state, VCHIQ_CONNSTATE_CONNECTED);
-+ vchiq_platform_resumed(state);
-+ break;
-+
-+ case VCHIQ_MSG_REMOTE_USE:
-+ vchiq_on_remote_use(state);
-+ break;
-+ case VCHIQ_MSG_REMOTE_RELEASE:
-+ vchiq_on_remote_release(state);
-+ break;
-+ case VCHIQ_MSG_REMOTE_USE_ACTIVE:
-+ vchiq_on_remote_use_active(state);
-+ break;
-+
-+ default:
-+ vchiq_log_error(vchiq_core_log_level,
-+ "%d: prs invalid msgid %x@%x,%x",
-+ state->id, msgid, (unsigned int)header, size);
-+ WARN(1, "invalid message\n");
-+ break;
-+ }
-+
-+skip_message:
-+ if (service) {
-+ unlock_service(service);
-+ service = NULL;
-+ }
-+
-+ state->rx_pos += calc_stride(size);
-+
-+ DEBUG_TRACE(PARSE_LINE);
-+ /* Perform some housekeeping when the end of the slot is
-+ ** reached. */
-+ if ((state->rx_pos & VCHIQ_SLOT_MASK) == 0) {
-+ /* Remove the extra reference count. */
-+ release_slot(state, state->rx_info, NULL, NULL);
-+ state->rx_data = NULL;
-+ }
-+ }
-+
-+bail_not_ready:
-+ if (service)
-+ unlock_service(service);
-+}
-+
-+/* Called by the slot handler thread */
-+static int
-+slot_handler_func(void *v)
-+{
-+ VCHIQ_STATE_T *state = (VCHIQ_STATE_T *) v;
-+ VCHIQ_SHARED_STATE_T *local = state->local;
-+ DEBUG_INITIALISE(local)
-+
-+ while (1) {
-+ DEBUG_COUNT(SLOT_HANDLER_COUNT);
-+ DEBUG_TRACE(SLOT_HANDLER_LINE);
-+ remote_event_wait(&local->trigger);
-+
-+ rmb();
-+
-+ DEBUG_TRACE(SLOT_HANDLER_LINE);
-+ if (state->poll_needed) {
-+ /* Check if we need to suspend - may change our
-+ * conn_state */
-+ vchiq_platform_check_suspend(state);
-+
-+ state->poll_needed = 0;
-+
-+ /* Handle service polling and other rare conditions here
-+ ** out of the mainline code */
-+ switch (state->conn_state) {
-+ case VCHIQ_CONNSTATE_CONNECTED:
-+ /* Poll the services as requested */
-+ poll_services(state);
-+ break;
-+
-+ case VCHIQ_CONNSTATE_PAUSING:
-+ if (state->is_master)
-+ pause_bulks(state);
-+ if (queue_message(state, NULL,
-+ VCHIQ_MAKE_MSG(VCHIQ_MSG_PAUSE, 0, 0),
-+ NULL, 0, 0,
-+ QMFLAGS_NO_MUTEX_UNLOCK)
-+ != VCHIQ_RETRY) {
-+ vchiq_set_conn_state(state,
-+ VCHIQ_CONNSTATE_PAUSE_SENT);
-+ } else {
-+ if (state->is_master)
-+ resume_bulks(state);
-+ /* Retry later */
-+ state->poll_needed = 1;
-+ }
-+ break;
-+
-+ case VCHIQ_CONNSTATE_PAUSED:
-+ vchiq_platform_resume(state);
-+ break;
-+
-+ case VCHIQ_CONNSTATE_RESUMING:
-+ if (queue_message(state, NULL,
-+ VCHIQ_MAKE_MSG(VCHIQ_MSG_RESUME, 0, 0),
-+ NULL, 0, 0, QMFLAGS_NO_MUTEX_LOCK)
-+ != VCHIQ_RETRY) {
-+ if (state->is_master)
-+ resume_bulks(state);
-+ vchiq_set_conn_state(state,
-+ VCHIQ_CONNSTATE_CONNECTED);
-+ vchiq_platform_resumed(state);
-+ } else {
-+ /* This should really be impossible,
-+ ** since the PAUSE should have flushed
-+ ** through outstanding messages. */
-+ vchiq_log_error(vchiq_core_log_level,
-+ "Failed to send RESUME "
-+ "message");
-+ BUG();
-+ }
-+ break;
-+
-+ case VCHIQ_CONNSTATE_PAUSE_TIMEOUT:
-+ case VCHIQ_CONNSTATE_RESUME_TIMEOUT:
-+ vchiq_platform_handle_timeout(state);
-+ break;
-+ default:
-+ break;
-+ }
-+
-+
-+ }
-+
-+ DEBUG_TRACE(SLOT_HANDLER_LINE);
-+ parse_rx_slots(state);
-+ }
-+ return 0;
-+}
-+
-+
-+/* Called by the recycle thread */
-+static int
-+recycle_func(void *v)
-+{
-+ VCHIQ_STATE_T *state = (VCHIQ_STATE_T *) v;
-+ VCHIQ_SHARED_STATE_T *local = state->local;
-+
-+ while (1) {
-+ remote_event_wait(&local->recycle);
-+
-+ process_free_queue(state);
-+ }
-+ return 0;
-+}
-+
-+
-+/* Called by the sync thread */
-+static int
-+sync_func(void *v)
-+{
-+ VCHIQ_STATE_T *state = (VCHIQ_STATE_T *) v;
-+ VCHIQ_SHARED_STATE_T *local = state->local;
-+ VCHIQ_HEADER_T *header = (VCHIQ_HEADER_T *)SLOT_DATA_FROM_INDEX(state,
-+ state->remote->slot_sync);
-+
-+ while (1) {
-+ VCHIQ_SERVICE_T *service;
-+ int msgid, size;
-+ int type;
-+ unsigned int localport, remoteport;
-+
-+ remote_event_wait(&local->sync_trigger);
-+
-+ rmb();
-+
-+ msgid = header->msgid;
-+ size = header->size;
-+ type = VCHIQ_MSG_TYPE(msgid);
-+ localport = VCHIQ_MSG_DSTPORT(msgid);
-+ remoteport = VCHIQ_MSG_SRCPORT(msgid);
-+
-+ service = find_service_by_port(state, localport);
-+
-+ if (!service) {
-+ vchiq_log_error(vchiq_sync_log_level,
-+ "%d: sf %s@%x (%d->%d) - "
-+ "invalid/closed service %d",
-+ state->id, msg_type_str(type),
-+ (unsigned int)header,
-+ remoteport, localport, localport);
-+ release_message_sync(state, header);
-+ continue;
-+ }
-+
-+ if (vchiq_sync_log_level >= VCHIQ_LOG_TRACE) {
-+ int svc_fourcc;
-+
-+ svc_fourcc = service
-+ ? service->base.fourcc
-+ : VCHIQ_MAKE_FOURCC('?', '?', '?', '?');
-+ vchiq_log_trace(vchiq_sync_log_level,
-+ "Rcvd Msg %s from %c%c%c%c s:%d d:%d len:%d",
-+ msg_type_str(type),
-+ VCHIQ_FOURCC_AS_4CHARS(svc_fourcc),
-+ remoteport, localport, size);
-+ if (size > 0)
-+ vchiq_log_dump_mem("Rcvd", 0, header->data,
-+ min(64, size));
-+ }
-+
-+ switch (type) {
-+ case VCHIQ_MSG_OPENACK:
-+ if (size >= sizeof(struct vchiq_openack_payload)) {
-+ const struct vchiq_openack_payload *payload =
-+ (struct vchiq_openack_payload *)
-+ header->data;
-+ service->peer_version = payload->version;
-+ }
-+ vchiq_log_info(vchiq_sync_log_level,
-+ "%d: sf OPENACK@%x,%x (%d->%d) v:%d",
-+ state->id, (unsigned int)header, size,
-+ remoteport, localport, service->peer_version);
-+ if (service->srvstate == VCHIQ_SRVSTATE_OPENING) {
-+ service->remoteport = remoteport;
-+ vchiq_set_service_state(service,
-+ VCHIQ_SRVSTATE_OPENSYNC);
-+ service->sync = 1;
-+ up(&service->remove_event);
-+ }
-+ release_message_sync(state, header);
-+ break;
-+
-+ case VCHIQ_MSG_DATA:
-+ vchiq_log_trace(vchiq_sync_log_level,
-+ "%d: sf DATA@%x,%x (%d->%d)",
-+ state->id, (unsigned int)header, size,
-+ remoteport, localport);
-+
-+ if ((service->remoteport == remoteport) &&
-+ (service->srvstate ==
-+ VCHIQ_SRVSTATE_OPENSYNC)) {
-+ if (make_service_callback(service,
-+ VCHIQ_MESSAGE_AVAILABLE, header,
-+ NULL) == VCHIQ_RETRY)
-+ vchiq_log_error(vchiq_sync_log_level,
-+ "synchronous callback to "
-+ "service %d returns "
-+ "VCHIQ_RETRY",
-+ localport);
-+ }
-+ break;
-+
-+ default:
-+ vchiq_log_error(vchiq_sync_log_level,
-+ "%d: sf unexpected msgid %x@%x,%x",
-+ state->id, msgid, (unsigned int)header, size);
-+ release_message_sync(state, header);
-+ break;
-+ }
-+
-+ unlock_service(service);
-+ }
-+
-+ return 0;
-+}
-+
-+
-+static void
-+init_bulk_queue(VCHIQ_BULK_QUEUE_T *queue)
-+{
-+ queue->local_insert = 0;
-+ queue->remote_insert = 0;
-+ queue->process = 0;
-+ queue->remote_notify = 0;
-+ queue->remove = 0;
-+}
-+
-+
-+inline const char *
-+get_conn_state_name(VCHIQ_CONNSTATE_T conn_state)
-+{
-+ return conn_state_names[conn_state];
-+}
-+
-+
-+VCHIQ_SLOT_ZERO_T *
-+vchiq_init_slots(void *mem_base, int mem_size)
-+{
-+ int mem_align = (VCHIQ_SLOT_SIZE - (int)mem_base) & VCHIQ_SLOT_MASK;
-+ VCHIQ_SLOT_ZERO_T *slot_zero =
-+ (VCHIQ_SLOT_ZERO_T *)((char *)mem_base + mem_align);
-+ int num_slots = (mem_size - mem_align)/VCHIQ_SLOT_SIZE;
-+ int first_data_slot = VCHIQ_SLOT_ZERO_SLOTS;
-+
-+ /* Ensure there is enough memory to run an absolutely minimum system */
-+ num_slots -= first_data_slot;
-+
-+ if (num_slots < 4) {
-+ vchiq_log_error(vchiq_core_log_level,
-+ "vchiq_init_slots - insufficient memory %x bytes",
-+ mem_size);
-+ return NULL;
-+ }
-+
-+ memset(slot_zero, 0, sizeof(VCHIQ_SLOT_ZERO_T));
-+
-+ slot_zero->magic = VCHIQ_MAGIC;
-+ slot_zero->version = VCHIQ_VERSION;
-+ slot_zero->version_min = VCHIQ_VERSION_MIN;
-+ slot_zero->slot_zero_size = sizeof(VCHIQ_SLOT_ZERO_T);
-+ slot_zero->slot_size = VCHIQ_SLOT_SIZE;
-+ slot_zero->max_slots = VCHIQ_MAX_SLOTS;
-+ slot_zero->max_slots_per_side = VCHIQ_MAX_SLOTS_PER_SIDE;
-+
-+ slot_zero->master.slot_sync = first_data_slot;
-+ slot_zero->master.slot_first = first_data_slot + 1;
-+ slot_zero->master.slot_last = first_data_slot + (num_slots/2) - 1;
-+ slot_zero->slave.slot_sync = first_data_slot + (num_slots/2);
-+ slot_zero->slave.slot_first = first_data_slot + (num_slots/2) + 1;
-+ slot_zero->slave.slot_last = first_data_slot + num_slots - 1;
-+
-+ return slot_zero;
-+}
-+
-+VCHIQ_STATUS_T
-+vchiq_init_state(VCHIQ_STATE_T *state, VCHIQ_SLOT_ZERO_T *slot_zero,
-+ int is_master)
-+{
-+ VCHIQ_SHARED_STATE_T *local;
-+ VCHIQ_SHARED_STATE_T *remote;
-+ VCHIQ_STATUS_T status;
-+ char threadname[10];
-+ static int id;
-+ int i;
-+
-+ vchiq_log_warning(vchiq_core_log_level,
-+ "%s: slot_zero = 0x%08lx, is_master = %d",
-+ __func__, (unsigned long)slot_zero, is_master);
-+
-+ /* Check the input configuration */
-+
-+ if (slot_zero->magic != VCHIQ_MAGIC) {
-+ vchiq_loud_error_header();
-+ vchiq_loud_error("Invalid VCHIQ magic value found.");
-+ vchiq_loud_error("slot_zero=%x: magic=%x (expected %x)",
-+ (unsigned int)slot_zero, slot_zero->magic, VCHIQ_MAGIC);
-+ vchiq_loud_error_footer();
-+ return VCHIQ_ERROR;
-+ }
-+
-+ if (slot_zero->version < VCHIQ_VERSION_MIN) {
-+ vchiq_loud_error_header();
-+ vchiq_loud_error("Incompatible VCHIQ versions found.");
-+ vchiq_loud_error("slot_zero=%x: VideoCore version=%d "
-+ "(minimum %d)",
-+ (unsigned int)slot_zero, slot_zero->version,
-+ VCHIQ_VERSION_MIN);
-+ vchiq_loud_error("Restart with a newer VideoCore image.");
-+ vchiq_loud_error_footer();
-+ return VCHIQ_ERROR;
-+ }
-+
-+ if (VCHIQ_VERSION < slot_zero->version_min) {
-+ vchiq_loud_error_header();
-+ vchiq_loud_error("Incompatible VCHIQ versions found.");
-+ vchiq_loud_error("slot_zero=%x: version=%d (VideoCore "
-+ "minimum %d)",
-+ (unsigned int)slot_zero, VCHIQ_VERSION,
-+ slot_zero->version_min);
-+ vchiq_loud_error("Restart with a newer kernel.");
-+ vchiq_loud_error_footer();
-+ return VCHIQ_ERROR;
-+ }
-+
-+ if ((slot_zero->slot_zero_size != sizeof(VCHIQ_SLOT_ZERO_T)) ||
-+ (slot_zero->slot_size != VCHIQ_SLOT_SIZE) ||
-+ (slot_zero->max_slots != VCHIQ_MAX_SLOTS) ||
-+ (slot_zero->max_slots_per_side != VCHIQ_MAX_SLOTS_PER_SIDE)) {
-+ vchiq_loud_error_header();
-+ if (slot_zero->slot_zero_size != sizeof(VCHIQ_SLOT_ZERO_T))
-+ vchiq_loud_error("slot_zero=%x: slot_zero_size=%x "
-+ "(expected %x)",
-+ (unsigned int)slot_zero,
-+ slot_zero->slot_zero_size,
-+ sizeof(VCHIQ_SLOT_ZERO_T));
-+ if (slot_zero->slot_size != VCHIQ_SLOT_SIZE)
-+ vchiq_loud_error("slot_zero=%x: slot_size=%d "
-+ "(expected %d",
-+ (unsigned int)slot_zero, slot_zero->slot_size,
-+ VCHIQ_SLOT_SIZE);
-+ if (slot_zero->max_slots != VCHIQ_MAX_SLOTS)
-+ vchiq_loud_error("slot_zero=%x: max_slots=%d "
-+ "(expected %d)",
-+ (unsigned int)slot_zero, slot_zero->max_slots,
-+ VCHIQ_MAX_SLOTS);
-+ if (slot_zero->max_slots_per_side != VCHIQ_MAX_SLOTS_PER_SIDE)
-+ vchiq_loud_error("slot_zero=%x: max_slots_per_side=%d "
-+ "(expected %d)",
-+ (unsigned int)slot_zero,
-+ slot_zero->max_slots_per_side,
-+ VCHIQ_MAX_SLOTS_PER_SIDE);
-+ vchiq_loud_error_footer();
-+ return VCHIQ_ERROR;
-+ }
-+
-+ if (VCHIQ_VERSION < slot_zero->version)
-+ slot_zero->version = VCHIQ_VERSION;
-+
-+ if (is_master) {
-+ local = &slot_zero->master;
-+ remote = &slot_zero->slave;
-+ } else {
-+ local = &slot_zero->slave;
-+ remote = &slot_zero->master;
-+ }
-+
-+ if (local->initialised) {
-+ vchiq_loud_error_header();
-+ if (remote->initialised)
-+ vchiq_loud_error("local state has already been "
-+ "initialised");
-+ else
-+ vchiq_loud_error("master/slave mismatch - two %ss",
-+ is_master ? "master" : "slave");
-+ vchiq_loud_error_footer();
-+ return VCHIQ_ERROR;
-+ }
-+
-+ memset(state, 0, sizeof(VCHIQ_STATE_T));
-+
-+ state->id = id++;
-+ state->is_master = is_master;
-+
-+ /*
-+ initialize shared state pointers
-+ */
-+
-+ state->local = local;
-+ state->remote = remote;
-+ state->slot_data = (VCHIQ_SLOT_T *)slot_zero;
-+
-+ /*
-+ initialize events and mutexes
-+ */
-+
-+ sema_init(&state->connect, 0);
-+ mutex_init(&state->mutex);
-+ sema_init(&state->trigger_event, 0);
-+ sema_init(&state->recycle_event, 0);
-+ sema_init(&state->sync_trigger_event, 0);
-+ sema_init(&state->sync_release_event, 0);
-+
-+ mutex_init(&state->slot_mutex);
-+ mutex_init(&state->recycle_mutex);
-+ mutex_init(&state->sync_mutex);
-+ mutex_init(&state->bulk_transfer_mutex);
-+
-+ sema_init(&state->slot_available_event, 0);
-+ sema_init(&state->slot_remove_event, 0);
-+ sema_init(&state->data_quota_event, 0);
-+
-+ state->slot_queue_available = 0;
-+
-+ for (i = 0; i < VCHIQ_MAX_SERVICES; i++) {
-+ VCHIQ_SERVICE_QUOTA_T *service_quota =
-+ &state->service_quotas[i];
-+ sema_init(&service_quota->quota_event, 0);
-+ }
-+
-+ for (i = local->slot_first; i <= local->slot_last; i++) {
-+ local->slot_queue[state->slot_queue_available++] = i;
-+ up(&state->slot_available_event);
-+ }
-+
-+ state->default_slot_quota = state->slot_queue_available/2;
-+ state->default_message_quota =
-+ min((unsigned short)(state->default_slot_quota * 256),
-+ (unsigned short)~0);
-+
-+ state->previous_data_index = -1;
-+ state->data_use_count = 0;
-+ state->data_quota = state->slot_queue_available - 1;
-+
-+ local->trigger.event = &state->trigger_event;
-+ remote_event_create(&local->trigger);
-+ local->tx_pos = 0;
-+
-+ local->recycle.event = &state->recycle_event;
-+ remote_event_create(&local->recycle);
-+ local->slot_queue_recycle = state->slot_queue_available;
-+
-+ local->sync_trigger.event = &state->sync_trigger_event;
-+ remote_event_create(&local->sync_trigger);
-+
-+ local->sync_release.event = &state->sync_release_event;
-+ remote_event_create(&local->sync_release);
-+
-+ /* At start-of-day, the slot is empty and available */
-+ ((VCHIQ_HEADER_T *)SLOT_DATA_FROM_INDEX(state, local->slot_sync))->msgid
-+ = VCHIQ_MSGID_PADDING;
-+ remote_event_signal_local(&local->sync_release);
-+
-+ local->debug[DEBUG_ENTRIES] = DEBUG_MAX;
-+
-+ status = vchiq_platform_init_state(state);
-+
-+ /*
-+ bring up slot handler thread
-+ */
-+ snprintf(threadname, sizeof(threadname), "VCHIQ-%d", state->id);
-+ state->slot_handler_thread = kthread_create(&slot_handler_func,
-+ (void *)state,
-+ threadname);
-+
-+ if (state->slot_handler_thread == NULL) {
-+ vchiq_loud_error_header();
-+ vchiq_loud_error("couldn't create thread %s", threadname);
-+ vchiq_loud_error_footer();
-+ return VCHIQ_ERROR;
-+ }
-+ set_user_nice(state->slot_handler_thread, -19);
-+ wake_up_process(state->slot_handler_thread);
-+
-+ snprintf(threadname, sizeof(threadname), "VCHIQr-%d", state->id);
-+ state->recycle_thread = kthread_create(&recycle_func,
-+ (void *)state,
-+ threadname);
-+ if (state->recycle_thread == NULL) {
-+ vchiq_loud_error_header();
-+ vchiq_loud_error("couldn't create thread %s", threadname);
-+ vchiq_loud_error_footer();
-+ return VCHIQ_ERROR;
-+ }
-+ set_user_nice(state->recycle_thread, -19);
-+ wake_up_process(state->recycle_thread);
-+
-+ snprintf(threadname, sizeof(threadname), "VCHIQs-%d", state->id);
-+ state->sync_thread = kthread_create(&sync_func,
-+ (void *)state,
-+ threadname);
-+ if (state->sync_thread == NULL) {
-+ vchiq_loud_error_header();
-+ vchiq_loud_error("couldn't create thread %s", threadname);
-+ vchiq_loud_error_footer();
-+ return VCHIQ_ERROR;
-+ }
-+ set_user_nice(state->sync_thread, -20);
-+ wake_up_process(state->sync_thread);
-+
-+ BUG_ON(state->id >= VCHIQ_MAX_STATES);
-+ vchiq_states[state->id] = state;
-+
-+ /* Indicate readiness to the other side */
-+ local->initialised = 1;
-+
-+ return status;
-+}
-+
-+/* Called from application thread when a client or server service is created. */
-+VCHIQ_SERVICE_T *
-+vchiq_add_service_internal(VCHIQ_STATE_T *state,
-+ const VCHIQ_SERVICE_PARAMS_T *params, int srvstate,
-+ VCHIQ_INSTANCE_T instance, VCHIQ_USERDATA_TERM_T userdata_term)
-+{
-+ VCHIQ_SERVICE_T *service;
-+
-+ service = kmalloc(sizeof(VCHIQ_SERVICE_T), GFP_KERNEL);
-+ if (service) {
-+ service->base.fourcc = params->fourcc;
-+ service->base.callback = params->callback;
-+ service->base.userdata = params->userdata;
-+ service->handle = VCHIQ_SERVICE_HANDLE_INVALID;
-+ service->ref_count = 1;
-+ service->srvstate = VCHIQ_SRVSTATE_FREE;
-+ service->userdata_term = userdata_term;
-+ service->localport = VCHIQ_PORT_FREE;
-+ service->remoteport = VCHIQ_PORT_FREE;
-+
-+ service->public_fourcc = (srvstate == VCHIQ_SRVSTATE_OPENING) ?
-+ VCHIQ_FOURCC_INVALID : params->fourcc;
-+ service->client_id = 0;
-+ service->auto_close = 1;
-+ service->sync = 0;
-+ service->closing = 0;
-+ service->trace = 0;
-+ atomic_set(&service->poll_flags, 0);
-+ service->version = params->version;
-+ service->version_min = params->version_min;
-+ service->state = state;
-+ service->instance = instance;
-+ service->service_use_count = 0;
-+ init_bulk_queue(&service->bulk_tx);
-+ init_bulk_queue(&service->bulk_rx);
-+ sema_init(&service->remove_event, 0);
-+ sema_init(&service->bulk_remove_event, 0);
-+ mutex_init(&service->bulk_mutex);
-+ memset(&service->stats, 0, sizeof(service->stats));
-+ } else {
-+ vchiq_log_error(vchiq_core_log_level,
-+ "Out of memory");
-+ }
-+
-+ if (service) {
-+ VCHIQ_SERVICE_T **pservice = NULL;
-+ int i;
-+
-+ /* Although it is perfectly possible to use service_spinlock
-+ ** to protect the creation of services, it is overkill as it
-+ ** disables interrupts while the array is searched.
-+ ** The only danger is of another thread trying to create a
-+ ** service - service deletion is safe.
-+ ** Therefore it is preferable to use state->mutex which,
-+ ** although slower to claim, doesn't block interrupts while
-+ ** it is held.
-+ */
-+
-+ mutex_lock(&state->mutex);
-+
-+ /* Prepare to use a previously unused service */
-+ if (state->unused_service < VCHIQ_MAX_SERVICES)
-+ pservice = &state->services[state->unused_service];
-+
-+ if (srvstate == VCHIQ_SRVSTATE_OPENING) {
-+ for (i = 0; i < state->unused_service; i++) {
-+ VCHIQ_SERVICE_T *srv = state->services[i];
-+ if (!srv) {
-+ pservice = &state->services[i];
-+ break;
-+ }
-+ }
-+ } else {
-+ for (i = (state->unused_service - 1); i >= 0; i--) {
-+ VCHIQ_SERVICE_T *srv = state->services[i];
-+ if (!srv)
-+ pservice = &state->services[i];
-+ else if ((srv->public_fourcc == params->fourcc)
-+ && ((srv->instance != instance) ||
-+ (srv->base.callback !=
-+ params->callback))) {
-+ /* There is another server using this
-+ ** fourcc which doesn't match. */
-+ pservice = NULL;
-+ break;
-+ }
-+ }
-+ }
-+
-+ if (pservice) {
-+ service->localport = (pservice - state->services);
-+ if (!handle_seq)
-+ handle_seq = VCHIQ_MAX_STATES *
-+ VCHIQ_MAX_SERVICES;
-+ service->handle = handle_seq |
-+ (state->id * VCHIQ_MAX_SERVICES) |
-+ service->localport;
-+ handle_seq += VCHIQ_MAX_STATES * VCHIQ_MAX_SERVICES;
-+ *pservice = service;
-+ if (pservice == &state->services[state->unused_service])
-+ state->unused_service++;
-+ }
-+
-+ mutex_unlock(&state->mutex);
-+
-+ if (!pservice) {
-+ kfree(service);
-+ service = NULL;
-+ }
-+ }
-+
-+ if (service) {
-+ VCHIQ_SERVICE_QUOTA_T *service_quota =
-+ &state->service_quotas[service->localport];
-+ service_quota->slot_quota = state->default_slot_quota;
-+ service_quota->message_quota = state->default_message_quota;
-+ if (service_quota->slot_use_count == 0)
-+ service_quota->previous_tx_index =
-+ SLOT_QUEUE_INDEX_FROM_POS(state->local_tx_pos)
-+ - 1;
-+
-+ /* Bring this service online */
-+ vchiq_set_service_state(service, srvstate);
-+
-+ vchiq_log_info(vchiq_core_msg_log_level,
-+ "%s Service %c%c%c%c SrcPort:%d",
-+ (srvstate == VCHIQ_SRVSTATE_OPENING)
-+ ? "Open" : "Add",
-+ VCHIQ_FOURCC_AS_4CHARS(params->fourcc),
-+ service->localport);
-+ }
-+
-+ /* Don't unlock the service - leave it with a ref_count of 1. */
-+
-+ return service;
-+}
-+
-+VCHIQ_STATUS_T
-+vchiq_open_service_internal(VCHIQ_SERVICE_T *service, int client_id)
-+{
-+ struct vchiq_open_payload payload = {
-+ service->base.fourcc,
-+ client_id,
-+ service->version,
-+ service->version_min
-+ };
-+ VCHIQ_ELEMENT_T body = { &payload, sizeof(payload) };
-+ VCHIQ_STATUS_T status = VCHIQ_SUCCESS;
-+
-+ service->client_id = client_id;
-+ vchiq_use_service_internal(service);
-+ status = queue_message(service->state, NULL,
-+ VCHIQ_MAKE_MSG(VCHIQ_MSG_OPEN, service->localport, 0),
-+ &body, 1, sizeof(payload), QMFLAGS_IS_BLOCKING);
-+ if (status == VCHIQ_SUCCESS) {
-+ /* Wait for the ACK/NAK */
-+ if (down_interruptible(&service->remove_event) != 0) {
-+ status = VCHIQ_RETRY;
-+ vchiq_release_service_internal(service);
-+ } else if ((service->srvstate != VCHIQ_SRVSTATE_OPEN) &&
-+ (service->srvstate != VCHIQ_SRVSTATE_OPENSYNC)) {
-+ if (service->srvstate != VCHIQ_SRVSTATE_CLOSEWAIT)
-+ vchiq_log_error(vchiq_core_log_level,
-+ "%d: osi - srvstate = %s (ref %d)",
-+ service->state->id,
-+ srvstate_names[service->srvstate],
-+ service->ref_count);
-+ status = VCHIQ_ERROR;
-+ VCHIQ_SERVICE_STATS_INC(service, error_count);
-+ vchiq_release_service_internal(service);
-+ }
-+ }
-+ return status;
-+}
-+
-+static void
-+release_service_messages(VCHIQ_SERVICE_T *service)
-+{
-+ VCHIQ_STATE_T *state = service->state;
-+ int slot_last = state->remote->slot_last;
-+ int i;
-+
-+ /* Release any claimed messages aimed at this service */
-+
-+ if (service->sync) {
-+ VCHIQ_HEADER_T *header =
-+ (VCHIQ_HEADER_T *)SLOT_DATA_FROM_INDEX(state,
-+ state->remote->slot_sync);
-+ if (VCHIQ_MSG_DSTPORT(header->msgid) == service->localport)
-+ release_message_sync(state, header);
-+
-+ return;
-+ }
-+
-+ for (i = state->remote->slot_first; i <= slot_last; i++) {
-+ VCHIQ_SLOT_INFO_T *slot_info =
-+ SLOT_INFO_FROM_INDEX(state, i);
-+ if (slot_info->release_count != slot_info->use_count) {
-+ char *data =
-+ (char *)SLOT_DATA_FROM_INDEX(state, i);
-+ unsigned int pos, end;
-+
-+ end = VCHIQ_SLOT_SIZE;
-+ if (data == state->rx_data)
-+ /* This buffer is still being read from - stop
-+ ** at the current read position */
-+ end = state->rx_pos & VCHIQ_SLOT_MASK;
-+
-+ pos = 0;
-+
-+ while (pos < end) {
-+ VCHIQ_HEADER_T *header =
-+ (VCHIQ_HEADER_T *)(data + pos);
-+ int msgid = header->msgid;
-+ int port = VCHIQ_MSG_DSTPORT(msgid);
-+ if ((port == service->localport) &&
-+ (msgid & VCHIQ_MSGID_CLAIMED)) {
-+ vchiq_log_info(vchiq_core_log_level,
-+ " fsi - hdr %x",
-+ (unsigned int)header);
-+ release_slot(state, slot_info, header,
-+ NULL);
-+ }
-+ pos += calc_stride(header->size);
-+ if (pos > VCHIQ_SLOT_SIZE) {
-+ vchiq_log_error(vchiq_core_log_level,
-+ "fsi - pos %x: header %x, "
-+ "msgid %x, header->msgid %x, "
-+ "header->size %x",
-+ pos, (unsigned int)header,
-+ msgid, header->msgid,
-+ header->size);
-+ WARN(1, "invalid slot position\n");
-+ }
-+ }
-+ }
-+ }
-+}
-+
-+static int
-+do_abort_bulks(VCHIQ_SERVICE_T *service)
-+{
-+ VCHIQ_STATUS_T status;
-+
-+ /* Abort any outstanding bulk transfers */
-+ if (mutex_lock_interruptible(&service->bulk_mutex) != 0)
-+ return 0;
-+ abort_outstanding_bulks(service, &service->bulk_tx);
-+ abort_outstanding_bulks(service, &service->bulk_rx);
-+ mutex_unlock(&service->bulk_mutex);
-+
-+ status = notify_bulks(service, &service->bulk_tx, 0/*!retry_poll*/);
-+ if (status == VCHIQ_SUCCESS)
-+ status = notify_bulks(service, &service->bulk_rx,
-+ 0/*!retry_poll*/);
-+ return (status == VCHIQ_SUCCESS);
-+}
-+
-+static VCHIQ_STATUS_T
-+close_service_complete(VCHIQ_SERVICE_T *service, int failstate)
-+{
-+ VCHIQ_STATUS_T status;
-+ int is_server = (service->public_fourcc != VCHIQ_FOURCC_INVALID);
-+ int newstate;
-+
-+ switch (service->srvstate) {
-+ case VCHIQ_SRVSTATE_OPEN:
-+ case VCHIQ_SRVSTATE_CLOSESENT:
-+ case VCHIQ_SRVSTATE_CLOSERECVD:
-+ if (is_server) {
-+ if (service->auto_close) {
-+ service->client_id = 0;
-+ service->remoteport = VCHIQ_PORT_FREE;
-+ newstate = VCHIQ_SRVSTATE_LISTENING;
-+ } else
-+ newstate = VCHIQ_SRVSTATE_CLOSEWAIT;
-+ } else
-+ newstate = VCHIQ_SRVSTATE_CLOSED;
-+ vchiq_set_service_state(service, newstate);
-+ break;
-+ case VCHIQ_SRVSTATE_LISTENING:
-+ break;
-+ default:
-+ vchiq_log_error(vchiq_core_log_level,
-+ "close_service_complete(%x) called in state %s",
-+ service->handle, srvstate_names[service->srvstate]);
-+ WARN(1, "close_service_complete in unexpected state\n");
-+ return VCHIQ_ERROR;
-+ }
-+
-+ status = make_service_callback(service,
-+ VCHIQ_SERVICE_CLOSED, NULL, NULL);
-+
-+ if (status != VCHIQ_RETRY) {
-+ int uc = service->service_use_count;
-+ int i;
-+ /* Complete the close process */
-+ for (i = 0; i < uc; i++)
-+ /* cater for cases where close is forced and the
-+ ** client may not close all it's handles */
-+ vchiq_release_service_internal(service);
-+
-+ service->client_id = 0;
-+ service->remoteport = VCHIQ_PORT_FREE;
-+
-+ if (service->srvstate == VCHIQ_SRVSTATE_CLOSED)
-+ vchiq_free_service_internal(service);
-+ else if (service->srvstate != VCHIQ_SRVSTATE_CLOSEWAIT) {
-+ if (is_server)
-+ service->closing = 0;
-+
-+ up(&service->remove_event);
-+ }
-+ } else
-+ vchiq_set_service_state(service, failstate);
-+
-+ return status;
-+}
-+
-+/* Called by the slot handler */
-+VCHIQ_STATUS_T
-+vchiq_close_service_internal(VCHIQ_SERVICE_T *service, int close_recvd)
-+{
-+ VCHIQ_STATE_T *state = service->state;
-+ VCHIQ_STATUS_T status = VCHIQ_SUCCESS;
-+ int is_server = (service->public_fourcc != VCHIQ_FOURCC_INVALID);
-+
-+ vchiq_log_info(vchiq_core_log_level, "%d: csi:%d,%d (%s)",
-+ service->state->id, service->localport, close_recvd,
-+ srvstate_names[service->srvstate]);
-+
-+ switch (service->srvstate) {
-+ case VCHIQ_SRVSTATE_CLOSED:
-+ case VCHIQ_SRVSTATE_HIDDEN:
-+ case VCHIQ_SRVSTATE_LISTENING:
-+ case VCHIQ_SRVSTATE_CLOSEWAIT:
-+ if (close_recvd)
-+ vchiq_log_error(vchiq_core_log_level,
-+ "vchiq_close_service_internal(1) called "
-+ "in state %s",
-+ srvstate_names[service->srvstate]);
-+ else if (is_server) {
-+ if (service->srvstate == VCHIQ_SRVSTATE_LISTENING) {
-+ status = VCHIQ_ERROR;
-+ } else {
-+ service->client_id = 0;
-+ service->remoteport = VCHIQ_PORT_FREE;
-+ if (service->srvstate ==
-+ VCHIQ_SRVSTATE_CLOSEWAIT)
-+ vchiq_set_service_state(service,
-+ VCHIQ_SRVSTATE_LISTENING);
-+ }
-+ up(&service->remove_event);
-+ } else
-+ vchiq_free_service_internal(service);
-+ break;
-+ case VCHIQ_SRVSTATE_OPENING:
-+ if (close_recvd) {
-+ /* The open was rejected - tell the user */
-+ vchiq_set_service_state(service,
-+ VCHIQ_SRVSTATE_CLOSEWAIT);
-+ up(&service->remove_event);
-+ } else {
-+ /* Shutdown mid-open - let the other side know */
-+ status = queue_message(state, service,
-+ VCHIQ_MAKE_MSG
-+ (VCHIQ_MSG_CLOSE,
-+ service->localport,
-+ VCHIQ_MSG_DSTPORT(service->remoteport)),
-+ NULL, 0, 0, 0);
-+ }
-+ break;
-+
-+ case VCHIQ_SRVSTATE_OPENSYNC:
-+ mutex_lock(&state->sync_mutex);
-+ /* Drop through */
-+
-+ case VCHIQ_SRVSTATE_OPEN:
-+ if (state->is_master || close_recvd) {
-+ if (!do_abort_bulks(service))
-+ status = VCHIQ_RETRY;
-+ }
-+
-+ release_service_messages(service);
-+
-+ if (status == VCHIQ_SUCCESS)
-+ status = queue_message(state, service,
-+ VCHIQ_MAKE_MSG
-+ (VCHIQ_MSG_CLOSE,
-+ service->localport,
-+ VCHIQ_MSG_DSTPORT(service->remoteport)),
-+ NULL, 0, 0, QMFLAGS_NO_MUTEX_UNLOCK);
-+
-+ if (status == VCHIQ_SUCCESS) {
-+ if (!close_recvd) {
-+ /* Change the state while the mutex is
-+ still held */
-+ vchiq_set_service_state(service,
-+ VCHIQ_SRVSTATE_CLOSESENT);
-+ mutex_unlock(&state->slot_mutex);
-+ if (service->sync)
-+ mutex_unlock(&state->sync_mutex);
-+ break;
-+ }
-+ } else if (service->srvstate == VCHIQ_SRVSTATE_OPENSYNC) {
-+ mutex_unlock(&state->sync_mutex);
-+ break;
-+ } else
-+ break;
-+
-+ /* Change the state while the mutex is still held */
-+ vchiq_set_service_state(service, VCHIQ_SRVSTATE_CLOSERECVD);
-+ mutex_unlock(&state->slot_mutex);
-+ if (service->sync)
-+ mutex_unlock(&state->sync_mutex);
-+
-+ status = close_service_complete(service,
-+ VCHIQ_SRVSTATE_CLOSERECVD);
-+ break;
-+
-+ case VCHIQ_SRVSTATE_CLOSESENT:
-+ if (!close_recvd)
-+ /* This happens when a process is killed mid-close */
-+ break;
-+
-+ if (!state->is_master) {
-+ if (!do_abort_bulks(service)) {
-+ status = VCHIQ_RETRY;
-+ break;
-+ }
-+ }
-+
-+ if (status == VCHIQ_SUCCESS)
-+ status = close_service_complete(service,
-+ VCHIQ_SRVSTATE_CLOSERECVD);
-+ break;
-+
-+ case VCHIQ_SRVSTATE_CLOSERECVD:
-+ if (!close_recvd && is_server)
-+ /* Force into LISTENING mode */
-+ vchiq_set_service_state(service,
-+ VCHIQ_SRVSTATE_LISTENING);
-+ status = close_service_complete(service,
-+ VCHIQ_SRVSTATE_CLOSERECVD);
-+ break;
-+
-+ default:
-+ vchiq_log_error(vchiq_core_log_level,
-+ "vchiq_close_service_internal(%d) called in state %s",
-+ close_recvd, srvstate_names[service->srvstate]);
-+ break;
-+ }
-+
-+ return status;
-+}
-+
-+/* Called from the application process upon process death */
-+void
-+vchiq_terminate_service_internal(VCHIQ_SERVICE_T *service)
-+{
-+ VCHIQ_STATE_T *state = service->state;
-+
-+ vchiq_log_info(vchiq_core_log_level, "%d: tsi - (%d<->%d)",
-+ state->id, service->localport, service->remoteport);
-+
-+ mark_service_closing(service);
-+
-+ /* Mark the service for removal by the slot handler */
-+ request_poll(state, service, VCHIQ_POLL_REMOVE);
-+}
-+
-+/* Called from the slot handler */
-+void
-+vchiq_free_service_internal(VCHIQ_SERVICE_T *service)
-+{
-+ VCHIQ_STATE_T *state = service->state;
-+
-+ vchiq_log_info(vchiq_core_log_level, "%d: fsi - (%d)",
-+ state->id, service->localport);
-+
-+ switch (service->srvstate) {
-+ case VCHIQ_SRVSTATE_OPENING:
-+ case VCHIQ_SRVSTATE_CLOSED:
-+ case VCHIQ_SRVSTATE_HIDDEN:
-+ case VCHIQ_SRVSTATE_LISTENING:
-+ case VCHIQ_SRVSTATE_CLOSEWAIT:
-+ break;
-+ default:
-+ vchiq_log_error(vchiq_core_log_level,
-+ "%d: fsi - (%d) in state %s",
-+ state->id, service->localport,
-+ srvstate_names[service->srvstate]);
-+ return;
-+ }
-+
-+ vchiq_set_service_state(service, VCHIQ_SRVSTATE_FREE);
-+
-+ up(&service->remove_event);
-+
-+ /* Release the initial lock */
-+ unlock_service(service);
-+}
-+
-+VCHIQ_STATUS_T
-+vchiq_connect_internal(VCHIQ_STATE_T *state, VCHIQ_INSTANCE_T instance)
-+{
-+ VCHIQ_SERVICE_T *service;
-+ int i;
-+
-+ /* Find all services registered to this client and enable them. */
-+ i = 0;
-+ while ((service = next_service_by_instance(state, instance,
-+ &i)) != NULL) {
-+ if (service->srvstate == VCHIQ_SRVSTATE_HIDDEN)
-+ vchiq_set_service_state(service,
-+ VCHIQ_SRVSTATE_LISTENING);
-+ unlock_service(service);
-+ }
-+
-+ if (state->conn_state == VCHIQ_CONNSTATE_DISCONNECTED) {
-+ if (queue_message(state, NULL,
-+ VCHIQ_MAKE_MSG(VCHIQ_MSG_CONNECT, 0, 0), NULL, 0,
-+ 0, QMFLAGS_IS_BLOCKING) == VCHIQ_RETRY)
-+ return VCHIQ_RETRY;
-+
-+ vchiq_set_conn_state(state, VCHIQ_CONNSTATE_CONNECTING);
-+ }
-+
-+ if (state->conn_state == VCHIQ_CONNSTATE_CONNECTING) {
-+ if (down_interruptible(&state->connect) != 0)
-+ return VCHIQ_RETRY;
-+
-+ vchiq_set_conn_state(state, VCHIQ_CONNSTATE_CONNECTED);
-+ up(&state->connect);
-+ }
-+
-+ return VCHIQ_SUCCESS;
-+}
-+
-+VCHIQ_STATUS_T
-+vchiq_shutdown_internal(VCHIQ_STATE_T *state, VCHIQ_INSTANCE_T instance)
-+{
-+ VCHIQ_SERVICE_T *service;
-+ int i;
-+
-+ /* Find all services registered to this client and enable them. */
-+ i = 0;
-+ while ((service = next_service_by_instance(state, instance,
-+ &i)) != NULL) {
-+ (void)vchiq_remove_service(service->handle);
-+ unlock_service(service);
-+ }
-+
-+ return VCHIQ_SUCCESS;
-+}
-+
-+VCHIQ_STATUS_T
-+vchiq_pause_internal(VCHIQ_STATE_T *state)
-+{
-+ VCHIQ_STATUS_T status = VCHIQ_SUCCESS;
-+
-+ switch (state->conn_state) {
-+ case VCHIQ_CONNSTATE_CONNECTED:
-+ /* Request a pause */
-+ vchiq_set_conn_state(state, VCHIQ_CONNSTATE_PAUSING);
-+ request_poll(state, NULL, 0);
-+ break;
-+ default:
-+ vchiq_log_error(vchiq_core_log_level,
-+ "vchiq_pause_internal in state %s\n",
-+ conn_state_names[state->conn_state]);
-+ status = VCHIQ_ERROR;
-+ VCHIQ_STATS_INC(state, error_count);
-+ break;
-+ }
-+
-+ return status;
-+}
-+
-+VCHIQ_STATUS_T
-+vchiq_resume_internal(VCHIQ_STATE_T *state)
-+{
-+ VCHIQ_STATUS_T status = VCHIQ_SUCCESS;
-+
-+ if (state->conn_state == VCHIQ_CONNSTATE_PAUSED) {
-+ vchiq_set_conn_state(state, VCHIQ_CONNSTATE_RESUMING);
-+ request_poll(state, NULL, 0);
-+ } else {
-+ status = VCHIQ_ERROR;
-+ VCHIQ_STATS_INC(state, error_count);
-+ }
-+
-+ return status;
-+}
-+
-+VCHIQ_STATUS_T
-+vchiq_close_service(VCHIQ_SERVICE_HANDLE_T handle)
-+{
-+ /* Unregister the service */
-+ VCHIQ_SERVICE_T *service = find_service_by_handle(handle);
-+ VCHIQ_STATUS_T status = VCHIQ_SUCCESS;
-+
-+ if (!service)
-+ return VCHIQ_ERROR;
-+
-+ vchiq_log_info(vchiq_core_log_level,
-+ "%d: close_service:%d",
-+ service->state->id, service->localport);
-+
-+ if ((service->srvstate == VCHIQ_SRVSTATE_FREE) ||
-+ (service->srvstate == VCHIQ_SRVSTATE_LISTENING) ||
-+ (service->srvstate == VCHIQ_SRVSTATE_HIDDEN)) {
-+ unlock_service(service);
-+ return VCHIQ_ERROR;
-+ }
-+
-+ mark_service_closing(service);
-+
-+ if (current == service->state->slot_handler_thread) {
-+ status = vchiq_close_service_internal(service,
-+ 0/*!close_recvd*/);
-+ BUG_ON(status == VCHIQ_RETRY);
-+ } else {
-+ /* Mark the service for termination by the slot handler */
-+ request_poll(service->state, service, VCHIQ_POLL_TERMINATE);
-+ }
-+
-+ while (1) {
-+ if (down_interruptible(&service->remove_event) != 0) {
-+ status = VCHIQ_RETRY;
-+ break;
-+ }
-+
-+ if ((service->srvstate == VCHIQ_SRVSTATE_FREE) ||
-+ (service->srvstate == VCHIQ_SRVSTATE_LISTENING) ||
-+ (service->srvstate == VCHIQ_SRVSTATE_OPEN))
-+ break;
-+
-+ vchiq_log_warning(vchiq_core_log_level,
-+ "%d: close_service:%d - waiting in state %s",
-+ service->state->id, service->localport,
-+ srvstate_names[service->srvstate]);
-+ }
-+
-+ if ((status == VCHIQ_SUCCESS) &&
-+ (service->srvstate != VCHIQ_SRVSTATE_FREE) &&
-+ (service->srvstate != VCHIQ_SRVSTATE_LISTENING))
-+ status = VCHIQ_ERROR;
-+
-+ unlock_service(service);
-+
-+ return status;
-+}
-+
-+VCHIQ_STATUS_T
-+vchiq_remove_service(VCHIQ_SERVICE_HANDLE_T handle)
-+{
-+ /* Unregister the service */
-+ VCHIQ_SERVICE_T *service = find_service_by_handle(handle);
-+ VCHIQ_STATUS_T status = VCHIQ_SUCCESS;
-+
-+ if (!service)
-+ return VCHIQ_ERROR;
-+
-+ vchiq_log_info(vchiq_core_log_level,
-+ "%d: remove_service:%d",
-+ service->state->id, service->localport);
-+
-+ if (service->srvstate == VCHIQ_SRVSTATE_FREE) {
-+ unlock_service(service);
-+ return VCHIQ_ERROR;
-+ }
-+
-+ mark_service_closing(service);
-+
-+ if ((service->srvstate == VCHIQ_SRVSTATE_HIDDEN) ||
-+ (current == service->state->slot_handler_thread)) {
-+ /* Make it look like a client, because it must be removed and
-+ not left in the LISTENING state. */
-+ service->public_fourcc = VCHIQ_FOURCC_INVALID;
-+
-+ status = vchiq_close_service_internal(service,
-+ 0/*!close_recvd*/);
-+ BUG_ON(status == VCHIQ_RETRY);
-+ } else {
-+ /* Mark the service for removal by the slot handler */
-+ request_poll(service->state, service, VCHIQ_POLL_REMOVE);
-+ }
-+ while (1) {
-+ if (down_interruptible(&service->remove_event) != 0) {
-+ status = VCHIQ_RETRY;
-+ break;
-+ }
-+
-+ if ((service->srvstate == VCHIQ_SRVSTATE_FREE) ||
-+ (service->srvstate == VCHIQ_SRVSTATE_OPEN))
-+ break;
-+
-+ vchiq_log_warning(vchiq_core_log_level,
-+ "%d: remove_service:%d - waiting in state %s",
-+ service->state->id, service->localport,
-+ srvstate_names[service->srvstate]);
-+ }
-+
-+ if ((status == VCHIQ_SUCCESS) &&
-+ (service->srvstate != VCHIQ_SRVSTATE_FREE))
-+ status = VCHIQ_ERROR;
-+
-+ unlock_service(service);
-+
-+ return status;
-+}
-+
-+
-+/* This function may be called by kernel threads or user threads.
-+ * User threads may receive VCHIQ_RETRY to indicate that a signal has been
-+ * received and the call should be retried after being returned to user
-+ * context.
-+ * When called in blocking mode, the userdata field points to a bulk_waiter
-+ * structure.
-+ */
-+VCHIQ_STATUS_T
-+vchiq_bulk_transfer(VCHIQ_SERVICE_HANDLE_T handle,
-+ VCHI_MEM_HANDLE_T memhandle, void *offset, int size, void *userdata,
-+ VCHIQ_BULK_MODE_T mode, VCHIQ_BULK_DIR_T dir)
-+{
-+ VCHIQ_SERVICE_T *service = find_service_by_handle(handle);
-+ VCHIQ_BULK_QUEUE_T *queue;
-+ VCHIQ_BULK_T *bulk;
-+ VCHIQ_STATE_T *state;
-+ struct bulk_waiter *bulk_waiter = NULL;
-+ const char dir_char = (dir == VCHIQ_BULK_TRANSMIT) ? 't' : 'r';
-+ const int dir_msgtype = (dir == VCHIQ_BULK_TRANSMIT) ?
-+ VCHIQ_MSG_BULK_TX : VCHIQ_MSG_BULK_RX;
-+ VCHIQ_STATUS_T status = VCHIQ_ERROR;
-+
-+ if (!service ||
-+ (service->srvstate != VCHIQ_SRVSTATE_OPEN) ||
-+ ((memhandle == VCHI_MEM_HANDLE_INVALID) && (offset == NULL)) ||
-+ (vchiq_check_service(service) != VCHIQ_SUCCESS))
-+ goto error_exit;
-+
-+ switch (mode) {
-+ case VCHIQ_BULK_MODE_NOCALLBACK:
-+ case VCHIQ_BULK_MODE_CALLBACK:
-+ break;
-+ case VCHIQ_BULK_MODE_BLOCKING:
-+ bulk_waiter = (struct bulk_waiter *)userdata;
-+ sema_init(&bulk_waiter->event, 0);
-+ bulk_waiter->actual = 0;
-+ bulk_waiter->bulk = NULL;
-+ break;
-+ case VCHIQ_BULK_MODE_WAITING:
-+ bulk_waiter = (struct bulk_waiter *)userdata;
-+ bulk = bulk_waiter->bulk;
-+ goto waiting;
-+ default:
-+ goto error_exit;
-+ }
-+
-+ state = service->state;
-+
-+ queue = (dir == VCHIQ_BULK_TRANSMIT) ?
-+ &service->bulk_tx : &service->bulk_rx;
-+
-+ if (mutex_lock_interruptible(&service->bulk_mutex) != 0) {
-+ status = VCHIQ_RETRY;
-+ goto error_exit;
-+ }
-+
-+ if (queue->local_insert == queue->remove + VCHIQ_NUM_SERVICE_BULKS) {
-+ VCHIQ_SERVICE_STATS_INC(service, bulk_stalls);
-+ do {
-+ mutex_unlock(&service->bulk_mutex);
-+ if (down_interruptible(&service->bulk_remove_event)
-+ != 0) {
-+ status = VCHIQ_RETRY;
-+ goto error_exit;
-+ }
-+ if (mutex_lock_interruptible(&service->bulk_mutex)
-+ != 0) {
-+ status = VCHIQ_RETRY;
-+ goto error_exit;
-+ }
-+ } while (queue->local_insert == queue->remove +
-+ VCHIQ_NUM_SERVICE_BULKS);
-+ }
-+
-+ bulk = &queue->bulks[BULK_INDEX(queue->local_insert)];
-+
-+ bulk->mode = mode;
-+ bulk->dir = dir;
-+ bulk->userdata = userdata;
-+ bulk->size = size;
-+ bulk->actual = VCHIQ_BULK_ACTUAL_ABORTED;
-+
-+ if (vchiq_prepare_bulk_data(bulk, memhandle, offset, size, dir) !=
-+ VCHIQ_SUCCESS)
-+ goto unlock_error_exit;
-+
-+ wmb();
-+
-+ vchiq_log_info(vchiq_core_log_level,
-+ "%d: bt (%d->%d) %cx %x@%x %x",
-+ state->id,
-+ service->localport, service->remoteport, dir_char,
-+ size, (unsigned int)bulk->data, (unsigned int)userdata);
-+
-+ /* The slot mutex must be held when the service is being closed, so
-+ claim it here to ensure that isn't happening */
-+ if (mutex_lock_interruptible(&state->slot_mutex) != 0) {
-+ status = VCHIQ_RETRY;
-+ goto cancel_bulk_error_exit;
-+ }
-+
-+ if (service->srvstate != VCHIQ_SRVSTATE_OPEN)
-+ goto unlock_both_error_exit;
-+
-+ if (state->is_master) {
-+ queue->local_insert++;
-+ if (resolve_bulks(service, queue))
-+ request_poll(state, service,
-+ (dir == VCHIQ_BULK_TRANSMIT) ?
-+ VCHIQ_POLL_TXNOTIFY : VCHIQ_POLL_RXNOTIFY);
-+ } else {
-+ int payload[2] = { (int)bulk->data, bulk->size };
-+ VCHIQ_ELEMENT_T element = { payload, sizeof(payload) };
-+
-+ status = queue_message(state, NULL,
-+ VCHIQ_MAKE_MSG(dir_msgtype,
-+ service->localport, service->remoteport),
-+ &element, 1, sizeof(payload),
-+ QMFLAGS_IS_BLOCKING |
-+ QMFLAGS_NO_MUTEX_LOCK |
-+ QMFLAGS_NO_MUTEX_UNLOCK);
-+ if (status != VCHIQ_SUCCESS) {
-+ goto unlock_both_error_exit;
-+ }
-+ queue->local_insert++;
-+ }
-+
-+ mutex_unlock(&state->slot_mutex);
-+ mutex_unlock(&service->bulk_mutex);
-+
-+ vchiq_log_trace(vchiq_core_log_level,
-+ "%d: bt:%d %cx li=%x ri=%x p=%x",
-+ state->id,
-+ service->localport, dir_char,
-+ queue->local_insert, queue->remote_insert, queue->process);
-+
-+waiting:
-+ unlock_service(service);
-+
-+ status = VCHIQ_SUCCESS;
-+
-+ if (bulk_waiter) {
-+ bulk_waiter->bulk = bulk;
-+ if (down_interruptible(&bulk_waiter->event) != 0)
-+ status = VCHIQ_RETRY;
-+ else if (bulk_waiter->actual == VCHIQ_BULK_ACTUAL_ABORTED)
-+ status = VCHIQ_ERROR;
-+ }
-+
-+ return status;
-+
-+unlock_both_error_exit:
-+ mutex_unlock(&state->slot_mutex);
-+cancel_bulk_error_exit:
-+ vchiq_complete_bulk(bulk);
-+unlock_error_exit:
-+ mutex_unlock(&service->bulk_mutex);
-+
-+error_exit:
-+ if (service)
-+ unlock_service(service);
-+ return status;
-+}
-+
-+VCHIQ_STATUS_T
-+vchiq_queue_message(VCHIQ_SERVICE_HANDLE_T handle,
-+ const VCHIQ_ELEMENT_T *elements, unsigned int count)
-+{
-+ VCHIQ_SERVICE_T *service = find_service_by_handle(handle);
-+ VCHIQ_STATUS_T status = VCHIQ_ERROR;
-+
-+ unsigned int size = 0;
-+ unsigned int i;
-+
-+ if (!service ||
-+ (vchiq_check_service(service) != VCHIQ_SUCCESS))
-+ goto error_exit;
-+
-+ for (i = 0; i < (unsigned int)count; i++) {
-+ if (elements[i].size) {
-+ if (elements[i].data == NULL) {
-+ VCHIQ_SERVICE_STATS_INC(service, error_count);
-+ goto error_exit;
-+ }
-+ size += elements[i].size;
-+ }
-+ }
-+
-+ if (size > VCHIQ_MAX_MSG_SIZE) {
-+ VCHIQ_SERVICE_STATS_INC(service, error_count);
-+ goto error_exit;
-+ }
-+
-+ switch (service->srvstate) {
-+ case VCHIQ_SRVSTATE_OPEN:
-+ status = queue_message(service->state, service,
-+ VCHIQ_MAKE_MSG(VCHIQ_MSG_DATA,
-+ service->localport,
-+ service->remoteport),
-+ elements, count, size, 1);
-+ break;
-+ case VCHIQ_SRVSTATE_OPENSYNC:
-+ status = queue_message_sync(service->state, service,
-+ VCHIQ_MAKE_MSG(VCHIQ_MSG_DATA,
-+ service->localport,
-+ service->remoteport),
-+ elements, count, size, 1);
-+ break;
-+ default:
-+ status = VCHIQ_ERROR;
-+ break;
-+ }
-+
-+error_exit:
-+ if (service)
-+ unlock_service(service);
-+
-+ return status;
-+}
-+
-+void
-+vchiq_release_message(VCHIQ_SERVICE_HANDLE_T handle, VCHIQ_HEADER_T *header)
-+{
-+ VCHIQ_SERVICE_T *service = find_service_by_handle(handle);
-+ VCHIQ_SHARED_STATE_T *remote;
-+ VCHIQ_STATE_T *state;
-+ int slot_index;
-+
-+ if (!service)
-+ return;
-+
-+ state = service->state;
-+ remote = state->remote;
-+
-+ slot_index = SLOT_INDEX_FROM_DATA(state, (void *)header);
-+
-+ if ((slot_index >= remote->slot_first) &&
-+ (slot_index <= remote->slot_last)) {
-+ int msgid = header->msgid;
-+ if (msgid & VCHIQ_MSGID_CLAIMED) {
-+ VCHIQ_SLOT_INFO_T *slot_info =
-+ SLOT_INFO_FROM_INDEX(state, slot_index);
-+
-+ release_slot(state, slot_info, header, service);
-+ }
-+ } else if (slot_index == remote->slot_sync)
-+ release_message_sync(state, header);
-+
-+ unlock_service(service);
-+}
-+
-+static void
-+release_message_sync(VCHIQ_STATE_T *state, VCHIQ_HEADER_T *header)
-+{
-+ header->msgid = VCHIQ_MSGID_PADDING;
-+ wmb();
-+ remote_event_signal(&state->remote->sync_release);
-+}
-+
-+VCHIQ_STATUS_T
-+vchiq_get_peer_version(VCHIQ_SERVICE_HANDLE_T handle, short *peer_version)
-+{
-+ VCHIQ_STATUS_T status = VCHIQ_ERROR;
-+ VCHIQ_SERVICE_T *service = find_service_by_handle(handle);
-+
-+ if (!service ||
-+ (vchiq_check_service(service) != VCHIQ_SUCCESS) ||
-+ !peer_version)
-+ goto exit;
-+ *peer_version = service->peer_version;
-+ status = VCHIQ_SUCCESS;
-+
-+exit:
-+ if (service)
-+ unlock_service(service);
-+ return status;
-+}
-+
-+VCHIQ_STATUS_T
-+vchiq_get_config(VCHIQ_INSTANCE_T instance,
-+ int config_size, VCHIQ_CONFIG_T *pconfig)
-+{
-+ VCHIQ_CONFIG_T config;
-+
-+ (void)instance;
-+
-+ config.max_msg_size = VCHIQ_MAX_MSG_SIZE;
-+ config.bulk_threshold = VCHIQ_MAX_MSG_SIZE;
-+ config.max_outstanding_bulks = VCHIQ_NUM_SERVICE_BULKS;
-+ config.max_services = VCHIQ_MAX_SERVICES;
-+ config.version = VCHIQ_VERSION;
-+ config.version_min = VCHIQ_VERSION_MIN;
-+
-+ if (config_size > sizeof(VCHIQ_CONFIG_T))
-+ return VCHIQ_ERROR;
-+
-+ memcpy(pconfig, &config,
-+ min(config_size, (int)(sizeof(VCHIQ_CONFIG_T))));
-+
-+ return VCHIQ_SUCCESS;
-+}
-+
-+VCHIQ_STATUS_T
-+vchiq_set_service_option(VCHIQ_SERVICE_HANDLE_T handle,
-+ VCHIQ_SERVICE_OPTION_T option, int value)
-+{
-+ VCHIQ_SERVICE_T *service = find_service_by_handle(handle);
-+ VCHIQ_STATUS_T status = VCHIQ_ERROR;
-+
-+ if (service) {
-+ switch (option) {
-+ case VCHIQ_SERVICE_OPTION_AUTOCLOSE:
-+ service->auto_close = value;
-+ status = VCHIQ_SUCCESS;
-+ break;
-+
-+ case VCHIQ_SERVICE_OPTION_SLOT_QUOTA: {
-+ VCHIQ_SERVICE_QUOTA_T *service_quota =
-+ &service->state->service_quotas[
-+ service->localport];
-+ if (value == 0)
-+ value = service->state->default_slot_quota;
-+ if ((value >= service_quota->slot_use_count) &&
-+ (value < (unsigned short)~0)) {
-+ service_quota->slot_quota = value;
-+ if ((value >= service_quota->slot_use_count) &&
-+ (service_quota->message_quota >=
-+ service_quota->message_use_count)) {
-+ /* Signal the service that it may have
-+ ** dropped below its quota */
-+ up(&service_quota->quota_event);
-+ }
-+ status = VCHIQ_SUCCESS;
-+ }
-+ } break;
-+
-+ case VCHIQ_SERVICE_OPTION_MESSAGE_QUOTA: {
-+ VCHIQ_SERVICE_QUOTA_T *service_quota =
-+ &service->state->service_quotas[
-+ service->localport];
-+ if (value == 0)
-+ value = service->state->default_message_quota;
-+ if ((value >= service_quota->message_use_count) &&
-+ (value < (unsigned short)~0)) {
-+ service_quota->message_quota = value;
-+ if ((value >=
-+ service_quota->message_use_count) &&
-+ (service_quota->slot_quota >=
-+ service_quota->slot_use_count))
-+ /* Signal the service that it may have
-+ ** dropped below its quota */
-+ up(&service_quota->quota_event);
-+ status = VCHIQ_SUCCESS;
-+ }
-+ } break;
-+
-+ case VCHIQ_SERVICE_OPTION_SYNCHRONOUS:
-+ if ((service->srvstate == VCHIQ_SRVSTATE_HIDDEN) ||
-+ (service->srvstate ==
-+ VCHIQ_SRVSTATE_LISTENING)) {
-+ service->sync = value;
-+ status = VCHIQ_SUCCESS;
-+ }
-+ break;
-+
-+ case VCHIQ_SERVICE_OPTION_TRACE:
-+ service->trace = value;
-+ status = VCHIQ_SUCCESS;
-+ break;
-+
-+ default:
-+ break;
-+ }
-+ unlock_service(service);
-+ }
-+
-+ return status;
-+}
-+
-+void
-+vchiq_dump_shared_state(void *dump_context, VCHIQ_STATE_T *state,
-+ VCHIQ_SHARED_STATE_T *shared, const char *label)
-+{
-+ static const char *const debug_names[] = {
-+ "<entries>",
-+ "SLOT_HANDLER_COUNT",
-+ "SLOT_HANDLER_LINE",
-+ "PARSE_LINE",
-+ "PARSE_HEADER",
-+ "PARSE_MSGID",
-+ "AWAIT_COMPLETION_LINE",
-+ "DEQUEUE_MESSAGE_LINE",
-+ "SERVICE_CALLBACK_LINE",
-+ "MSG_QUEUE_FULL_COUNT",
-+ "COMPLETION_QUEUE_FULL_COUNT"
-+ };
-+ int i;
-+
-+ char buf[80];
-+ int len;
-+ len = snprintf(buf, sizeof(buf),
-+ " %s: slots %d-%d tx_pos=%x recycle=%x",
-+ label, shared->slot_first, shared->slot_last,
-+ shared->tx_pos, shared->slot_queue_recycle);
-+ vchiq_dump(dump_context, buf, len + 1);
-+
-+ len = snprintf(buf, sizeof(buf),
-+ " Slots claimed:");
-+ vchiq_dump(dump_context, buf, len + 1);
-+
-+ for (i = shared->slot_first; i <= shared->slot_last; i++) {
-+ VCHIQ_SLOT_INFO_T slot_info = *SLOT_INFO_FROM_INDEX(state, i);
-+ if (slot_info.use_count != slot_info.release_count) {
-+ len = snprintf(buf, sizeof(buf),
-+ " %d: %d/%d", i, slot_info.use_count,
-+ slot_info.release_count);
-+ vchiq_dump(dump_context, buf, len + 1);
-+ }
-+ }
-+
-+ for (i = 1; i < shared->debug[DEBUG_ENTRIES]; i++) {
-+ len = snprintf(buf, sizeof(buf), " DEBUG: %s = %d(%x)",
-+ debug_names[i], shared->debug[i], shared->debug[i]);
-+ vchiq_dump(dump_context, buf, len + 1);
-+ }
-+}
-+
-+void
-+vchiq_dump_state(void *dump_context, VCHIQ_STATE_T *state)
-+{
-+ char buf[80];
-+ int len;
-+ int i;
-+
-+ len = snprintf(buf, sizeof(buf), "State %d: %s", state->id,
-+ conn_state_names[state->conn_state]);
-+ vchiq_dump(dump_context, buf, len + 1);
-+
-+ len = snprintf(buf, sizeof(buf),
-+ " tx_pos=%x(@%x), rx_pos=%x(@%x)",
-+ state->local->tx_pos,
-+ (uint32_t)state->tx_data +
-+ (state->local_tx_pos & VCHIQ_SLOT_MASK),
-+ state->rx_pos,
-+ (uint32_t)state->rx_data +
-+ (state->rx_pos & VCHIQ_SLOT_MASK));
-+ vchiq_dump(dump_context, buf, len + 1);
-+
-+ len = snprintf(buf, sizeof(buf),
-+ " Version: %d (min %d)",
-+ VCHIQ_VERSION, VCHIQ_VERSION_MIN);
-+ vchiq_dump(dump_context, buf, len + 1);
-+
-+ if (VCHIQ_ENABLE_STATS) {
-+ len = snprintf(buf, sizeof(buf),
-+ " Stats: ctrl_tx_count=%d, ctrl_rx_count=%d, "
-+ "error_count=%d",
-+ state->stats.ctrl_tx_count, state->stats.ctrl_rx_count,
-+ state->stats.error_count);
-+ vchiq_dump(dump_context, buf, len + 1);
-+ }
-+
-+ len = snprintf(buf, sizeof(buf),
-+ " Slots: %d available (%d data), %d recyclable, %d stalls "
-+ "(%d data)",
-+ ((state->slot_queue_available * VCHIQ_SLOT_SIZE) -
-+ state->local_tx_pos) / VCHIQ_SLOT_SIZE,
-+ state->data_quota - state->data_use_count,
-+ state->local->slot_queue_recycle - state->slot_queue_available,
-+ state->stats.slot_stalls, state->stats.data_stalls);
-+ vchiq_dump(dump_context, buf, len + 1);
-+
-+ vchiq_dump_platform_state(dump_context);
-+
-+ vchiq_dump_shared_state(dump_context, state, state->local, "Local");
-+ vchiq_dump_shared_state(dump_context, state, state->remote, "Remote");
-+
-+ vchiq_dump_platform_instances(dump_context);
-+
-+ for (i = 0; i < state->unused_service; i++) {
-+ VCHIQ_SERVICE_T *service = find_service_by_port(state, i);
-+
-+ if (service) {
-+ vchiq_dump_service_state(dump_context, service);
-+ unlock_service(service);
-+ }
-+ }
-+}
-+
-+void
-+vchiq_dump_service_state(void *dump_context, VCHIQ_SERVICE_T *service)
-+{
-+ char buf[80];
-+ int len;
-+
-+ len = snprintf(buf, sizeof(buf), "Service %d: %s (ref %u)",
-+ service->localport, srvstate_names[service->srvstate],
-+ service->ref_count - 1); /*Don't include the lock just taken*/
-+
-+ if (service->srvstate != VCHIQ_SRVSTATE_FREE) {
-+ char remoteport[30];
-+ VCHIQ_SERVICE_QUOTA_T *service_quota =
-+ &service->state->service_quotas[service->localport];
-+ int fourcc = service->base.fourcc;
-+ int tx_pending, rx_pending;
-+ if (service->remoteport != VCHIQ_PORT_FREE) {
-+ int len2 = snprintf(remoteport, sizeof(remoteport),
-+ "%d", service->remoteport);
-+ if (service->public_fourcc != VCHIQ_FOURCC_INVALID)
-+ snprintf(remoteport + len2,
-+ sizeof(remoteport) - len2,
-+ " (client %x)", service->client_id);
-+ } else
-+ strcpy(remoteport, "n/a");
-+
-+ len += snprintf(buf + len, sizeof(buf) - len,
-+ " '%c%c%c%c' remote %s (msg use %d/%d, slot use %d/%d)",
-+ VCHIQ_FOURCC_AS_4CHARS(fourcc),
-+ remoteport,
-+ service_quota->message_use_count,
-+ service_quota->message_quota,
-+ service_quota->slot_use_count,
-+ service_quota->slot_quota);
-+
-+ vchiq_dump(dump_context, buf, len + 1);
-+
-+ tx_pending = service->bulk_tx.local_insert -
-+ service->bulk_tx.remote_insert;
-+
-+ rx_pending = service->bulk_rx.local_insert -
-+ service->bulk_rx.remote_insert;
-+
-+ len = snprintf(buf, sizeof(buf),
-+ " Bulk: tx_pending=%d (size %d),"
-+ " rx_pending=%d (size %d)",
-+ tx_pending,
-+ tx_pending ? service->bulk_tx.bulks[
-+ BULK_INDEX(service->bulk_tx.remove)].size : 0,
-+ rx_pending,
-+ rx_pending ? service->bulk_rx.bulks[
-+ BULK_INDEX(service->bulk_rx.remove)].size : 0);
-+
-+ if (VCHIQ_ENABLE_STATS) {
-+ vchiq_dump(dump_context, buf, len + 1);
-+
-+ len = snprintf(buf, sizeof(buf),
-+ " Ctrl: tx_count=%d, tx_bytes=%llu, "
-+ "rx_count=%d, rx_bytes=%llu",
-+ service->stats.ctrl_tx_count,
-+ service->stats.ctrl_tx_bytes,
-+ service->stats.ctrl_rx_count,
-+ service->stats.ctrl_rx_bytes);
-+ vchiq_dump(dump_context, buf, len + 1);
-+
-+ len = snprintf(buf, sizeof(buf),
-+ " Bulk: tx_count=%d, tx_bytes=%llu, "
-+ "rx_count=%d, rx_bytes=%llu",
-+ service->stats.bulk_tx_count,
-+ service->stats.bulk_tx_bytes,
-+ service->stats.bulk_rx_count,
-+ service->stats.bulk_rx_bytes);
-+ vchiq_dump(dump_context, buf, len + 1);
-+
-+ len = snprintf(buf, sizeof(buf),
-+ " %d quota stalls, %d slot stalls, "
-+ "%d bulk stalls, %d aborted, %d errors",
-+ service->stats.quota_stalls,
-+ service->stats.slot_stalls,
-+ service->stats.bulk_stalls,
-+ service->stats.bulk_aborted_count,
-+ service->stats.error_count);
-+ }
-+ }
-+
-+ vchiq_dump(dump_context, buf, len + 1);
-+
-+ if (service->srvstate != VCHIQ_SRVSTATE_FREE)
-+ vchiq_dump_platform_service_state(dump_context, service);
-+}
-+
-+
-+void
-+vchiq_loud_error_header(void)
-+{
-+ vchiq_log_error(vchiq_core_log_level,
-+ "============================================================"
-+ "================");
-+ vchiq_log_error(vchiq_core_log_level,
-+ "============================================================"
-+ "================");
-+ vchiq_log_error(vchiq_core_log_level, "=====");
-+}
-+
-+void
-+vchiq_loud_error_footer(void)
-+{
-+ vchiq_log_error(vchiq_core_log_level, "=====");
-+ vchiq_log_error(vchiq_core_log_level,
-+ "============================================================"
-+ "================");
-+ vchiq_log_error(vchiq_core_log_level,
-+ "============================================================"
-+ "================");
-+}
-+
-+
-+VCHIQ_STATUS_T vchiq_send_remote_use(VCHIQ_STATE_T *state)
-+{
-+ VCHIQ_STATUS_T status = VCHIQ_RETRY;
-+ if (state->conn_state != VCHIQ_CONNSTATE_DISCONNECTED)
-+ status = queue_message(state, NULL,
-+ VCHIQ_MAKE_MSG(VCHIQ_MSG_REMOTE_USE, 0, 0),
-+ NULL, 0, 0, 0);
-+ return status;
-+}
-+
-+VCHIQ_STATUS_T vchiq_send_remote_release(VCHIQ_STATE_T *state)
-+{
-+ VCHIQ_STATUS_T status = VCHIQ_RETRY;
-+ if (state->conn_state != VCHIQ_CONNSTATE_DISCONNECTED)
-+ status = queue_message(state, NULL,
-+ VCHIQ_MAKE_MSG(VCHIQ_MSG_REMOTE_RELEASE, 0, 0),
-+ NULL, 0, 0, 0);
-+ return status;
-+}
-+
-+VCHIQ_STATUS_T vchiq_send_remote_use_active(VCHIQ_STATE_T *state)
-+{
-+ VCHIQ_STATUS_T status = VCHIQ_RETRY;
-+ if (state->conn_state != VCHIQ_CONNSTATE_DISCONNECTED)
-+ status = queue_message(state, NULL,
-+ VCHIQ_MAKE_MSG(VCHIQ_MSG_REMOTE_USE_ACTIVE, 0, 0),
-+ NULL, 0, 0, 0);
-+ return status;
-+}
-+
-+void vchiq_log_dump_mem(const char *label, uint32_t addr, const void *voidMem,
-+ size_t numBytes)
-+{
-+ const uint8_t *mem = (const uint8_t *)voidMem;
-+ size_t offset;
-+ char lineBuf[100];
-+ char *s;
-+
-+ while (numBytes > 0) {
-+ s = lineBuf;
-+
-+ for (offset = 0; offset < 16; offset++) {
-+ if (offset < numBytes)
-+ s += snprintf(s, 4, "%02x ", mem[offset]);
-+ else
-+ s += snprintf(s, 4, " ");
-+ }
-+
-+ for (offset = 0; offset < 16; offset++) {
-+ if (offset < numBytes) {
-+ uint8_t ch = mem[offset];
-+
-+ if ((ch < ' ') || (ch > '~'))
-+ ch = '.';
-+ *s++ = (char)ch;
-+ }
-+ }
-+ *s++ = '\0';
-+
-+ if ((label != NULL) && (*label != '\0'))
-+ vchiq_log_trace(VCHIQ_LOG_TRACE,
-+ "%s: %08x: %s", label, addr, lineBuf);
-+ else
-+ vchiq_log_trace(VCHIQ_LOG_TRACE,
-+ "%08x: %s", addr, lineBuf);
-+
-+ addr += 16;
-+ mem += 16;
-+ if (numBytes > 16)
-+ numBytes -= 16;
-+ else
-+ numBytes = 0;
-+ }
-+}
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_core.h
-@@ -0,0 +1,712 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#ifndef VCHIQ_CORE_H
-+#define VCHIQ_CORE_H
-+
-+#include <linux/mutex.h>
-+#include <linux/semaphore.h>
-+#include <linux/kthread.h>
-+
-+#include "vchiq_cfg.h"
-+
-+#include "vchiq.h"
-+
-+/* Run time control of log level, based on KERN_XXX level. */
-+#define VCHIQ_LOG_DEFAULT 4
-+#define VCHIQ_LOG_ERROR 3
-+#define VCHIQ_LOG_WARNING 4
-+#define VCHIQ_LOG_INFO 6
-+#define VCHIQ_LOG_TRACE 7
-+
-+#define VCHIQ_LOG_PREFIX KERN_INFO "vchiq: "
-+
-+#ifndef vchiq_log_error
-+#define vchiq_log_error(cat, fmt, ...) \
-+ do { if (cat >= VCHIQ_LOG_ERROR) \
-+ printk(VCHIQ_LOG_PREFIX fmt "\n", ##__VA_ARGS__); } while (0)
-+#endif
-+#ifndef vchiq_log_warning
-+#define vchiq_log_warning(cat, fmt, ...) \
-+ do { if (cat >= VCHIQ_LOG_WARNING) \
-+ printk(VCHIQ_LOG_PREFIX fmt "\n", ##__VA_ARGS__); } while (0)
-+#endif
-+#ifndef vchiq_log_info
-+#define vchiq_log_info(cat, fmt, ...) \
-+ do { if (cat >= VCHIQ_LOG_INFO) \
-+ printk(VCHIQ_LOG_PREFIX fmt "\n", ##__VA_ARGS__); } while (0)
-+#endif
-+#ifndef vchiq_log_trace
-+#define vchiq_log_trace(cat, fmt, ...) \
-+ do { if (cat >= VCHIQ_LOG_TRACE) \
-+ printk(VCHIQ_LOG_PREFIX fmt "\n", ##__VA_ARGS__); } while (0)
-+#endif
-+
-+#define vchiq_loud_error(...) \
-+ vchiq_log_error(vchiq_core_log_level, "===== " __VA_ARGS__)
-+
-+#ifndef vchiq_static_assert
-+#define vchiq_static_assert(cond) __attribute__((unused)) \
-+ extern int vchiq_static_assert[(cond) ? 1 : -1]
-+#endif
-+
-+#define IS_POW2(x) (x && ((x & (x - 1)) == 0))
-+
-+/* Ensure that the slot size and maximum number of slots are powers of 2 */
-+vchiq_static_assert(IS_POW2(VCHIQ_SLOT_SIZE));
-+vchiq_static_assert(IS_POW2(VCHIQ_MAX_SLOTS));
-+vchiq_static_assert(IS_POW2(VCHIQ_MAX_SLOTS_PER_SIDE));
-+
-+#define VCHIQ_SLOT_MASK (VCHIQ_SLOT_SIZE - 1)
-+#define VCHIQ_SLOT_QUEUE_MASK (VCHIQ_MAX_SLOTS_PER_SIDE - 1)
-+#define VCHIQ_SLOT_ZERO_SLOTS ((sizeof(VCHIQ_SLOT_ZERO_T) + \
-+ VCHIQ_SLOT_SIZE - 1) / VCHIQ_SLOT_SIZE)
-+
-+#define VCHIQ_MSG_PADDING 0 /* - */
-+#define VCHIQ_MSG_CONNECT 1 /* - */
-+#define VCHIQ_MSG_OPEN 2 /* + (srcport, -), fourcc, client_id */
-+#define VCHIQ_MSG_OPENACK 3 /* + (srcport, dstport) */
-+#define VCHIQ_MSG_CLOSE 4 /* + (srcport, dstport) */
-+#define VCHIQ_MSG_DATA 5 /* + (srcport, dstport) */
-+#define VCHIQ_MSG_BULK_RX 6 /* + (srcport, dstport), data, size */
-+#define VCHIQ_MSG_BULK_TX 7 /* + (srcport, dstport), data, size */
-+#define VCHIQ_MSG_BULK_RX_DONE 8 /* + (srcport, dstport), actual */
-+#define VCHIQ_MSG_BULK_TX_DONE 9 /* + (srcport, dstport), actual */
-+#define VCHIQ_MSG_PAUSE 10 /* - */
-+#define VCHIQ_MSG_RESUME 11 /* - */
-+#define VCHIQ_MSG_REMOTE_USE 12 /* - */
-+#define VCHIQ_MSG_REMOTE_RELEASE 13 /* - */
-+#define VCHIQ_MSG_REMOTE_USE_ACTIVE 14 /* - */
-+
-+#define VCHIQ_PORT_MAX (VCHIQ_MAX_SERVICES - 1)
-+#define VCHIQ_PORT_FREE 0x1000
-+#define VCHIQ_PORT_IS_VALID(port) (port < VCHIQ_PORT_FREE)
-+#define VCHIQ_MAKE_MSG(type, srcport, dstport) \
-+ ((type<<24) | (srcport<<12) | (dstport<<0))
-+#define VCHIQ_MSG_TYPE(msgid) ((unsigned int)msgid >> 24)
-+#define VCHIQ_MSG_SRCPORT(msgid) \
-+ (unsigned short)(((unsigned int)msgid >> 12) & 0xfff)
-+#define VCHIQ_MSG_DSTPORT(msgid) \
-+ ((unsigned short)msgid & 0xfff)
-+
-+#define VCHIQ_FOURCC_AS_4CHARS(fourcc) \
-+ ((fourcc) >> 24) & 0xff, \
-+ ((fourcc) >> 16) & 0xff, \
-+ ((fourcc) >> 8) & 0xff, \
-+ (fourcc) & 0xff
-+
-+/* Ensure the fields are wide enough */
-+vchiq_static_assert(VCHIQ_MSG_SRCPORT(VCHIQ_MAKE_MSG(0, 0, VCHIQ_PORT_MAX))
-+ == 0);
-+vchiq_static_assert(VCHIQ_MSG_TYPE(VCHIQ_MAKE_MSG(0, VCHIQ_PORT_MAX, 0)) == 0);
-+vchiq_static_assert((unsigned int)VCHIQ_PORT_MAX <
-+ (unsigned int)VCHIQ_PORT_FREE);
-+
-+#define VCHIQ_MSGID_PADDING VCHIQ_MAKE_MSG(VCHIQ_MSG_PADDING, 0, 0)
-+#define VCHIQ_MSGID_CLAIMED 0x40000000
-+
-+#define VCHIQ_FOURCC_INVALID 0x00000000
-+#define VCHIQ_FOURCC_IS_LEGAL(fourcc) (fourcc != VCHIQ_FOURCC_INVALID)
-+
-+#define VCHIQ_BULK_ACTUAL_ABORTED -1
-+
-+typedef uint32_t BITSET_T;
-+
-+vchiq_static_assert((sizeof(BITSET_T) * 8) == 32);
-+
-+#define BITSET_SIZE(b) ((b + 31) >> 5)
-+#define BITSET_WORD(b) (b >> 5)
-+#define BITSET_BIT(b) (1 << (b & 31))
-+#define BITSET_ZERO(bs) memset(bs, 0, sizeof(bs))
-+#define BITSET_IS_SET(bs, b) (bs[BITSET_WORD(b)] & BITSET_BIT(b))
-+#define BITSET_SET(bs, b) (bs[BITSET_WORD(b)] |= BITSET_BIT(b))
-+#define BITSET_CLR(bs, b) (bs[BITSET_WORD(b)] &= ~BITSET_BIT(b))
-+
-+#if VCHIQ_ENABLE_STATS
-+#define VCHIQ_STATS_INC(state, stat) (state->stats. stat++)
-+#define VCHIQ_SERVICE_STATS_INC(service, stat) (service->stats. stat++)
-+#define VCHIQ_SERVICE_STATS_ADD(service, stat, addend) \
-+ (service->stats. stat += addend)
-+#else
-+#define VCHIQ_STATS_INC(state, stat) ((void)0)
-+#define VCHIQ_SERVICE_STATS_INC(service, stat) ((void)0)
-+#define VCHIQ_SERVICE_STATS_ADD(service, stat, addend) ((void)0)
-+#endif
-+
-+enum {
-+ DEBUG_ENTRIES,
-+#if VCHIQ_ENABLE_DEBUG
-+ DEBUG_SLOT_HANDLER_COUNT,
-+ DEBUG_SLOT_HANDLER_LINE,
-+ DEBUG_PARSE_LINE,
-+ DEBUG_PARSE_HEADER,
-+ DEBUG_PARSE_MSGID,
-+ DEBUG_AWAIT_COMPLETION_LINE,
-+ DEBUG_DEQUEUE_MESSAGE_LINE,
-+ DEBUG_SERVICE_CALLBACK_LINE,
-+ DEBUG_MSG_QUEUE_FULL_COUNT,
-+ DEBUG_COMPLETION_QUEUE_FULL_COUNT,
-+#endif
-+ DEBUG_MAX
-+};
-+
-+#if VCHIQ_ENABLE_DEBUG
-+
-+#define DEBUG_INITIALISE(local) int *debug_ptr = (local)->debug;
-+#define DEBUG_TRACE(d) \
-+ do { debug_ptr[DEBUG_ ## d] = __LINE__; dsb(); } while (0)
-+#define DEBUG_VALUE(d, v) \
-+ do { debug_ptr[DEBUG_ ## d] = (v); dsb(); } while (0)
-+#define DEBUG_COUNT(d) \
-+ do { debug_ptr[DEBUG_ ## d]++; dsb(); } while (0)
-+
-+#else /* VCHIQ_ENABLE_DEBUG */
-+
-+#define DEBUG_INITIALISE(local)
-+#define DEBUG_TRACE(d)
-+#define DEBUG_VALUE(d, v)
-+#define DEBUG_COUNT(d)
-+
-+#endif /* VCHIQ_ENABLE_DEBUG */
-+
-+typedef enum {
-+ VCHIQ_CONNSTATE_DISCONNECTED,
-+ VCHIQ_CONNSTATE_CONNECTING,
-+ VCHIQ_CONNSTATE_CONNECTED,
-+ VCHIQ_CONNSTATE_PAUSING,
-+ VCHIQ_CONNSTATE_PAUSE_SENT,
-+ VCHIQ_CONNSTATE_PAUSED,
-+ VCHIQ_CONNSTATE_RESUMING,
-+ VCHIQ_CONNSTATE_PAUSE_TIMEOUT,
-+ VCHIQ_CONNSTATE_RESUME_TIMEOUT
-+} VCHIQ_CONNSTATE_T;
-+
-+enum {
-+ VCHIQ_SRVSTATE_FREE,
-+ VCHIQ_SRVSTATE_HIDDEN,
-+ VCHIQ_SRVSTATE_LISTENING,
-+ VCHIQ_SRVSTATE_OPENING,
-+ VCHIQ_SRVSTATE_OPEN,
-+ VCHIQ_SRVSTATE_OPENSYNC,
-+ VCHIQ_SRVSTATE_CLOSESENT,
-+ VCHIQ_SRVSTATE_CLOSERECVD,
-+ VCHIQ_SRVSTATE_CLOSEWAIT,
-+ VCHIQ_SRVSTATE_CLOSED
-+};
-+
-+enum {
-+ VCHIQ_POLL_TERMINATE,
-+ VCHIQ_POLL_REMOVE,
-+ VCHIQ_POLL_TXNOTIFY,
-+ VCHIQ_POLL_RXNOTIFY,
-+ VCHIQ_POLL_COUNT
-+};
-+
-+typedef enum {
-+ VCHIQ_BULK_TRANSMIT,
-+ VCHIQ_BULK_RECEIVE
-+} VCHIQ_BULK_DIR_T;
-+
-+typedef void (*VCHIQ_USERDATA_TERM_T)(void *userdata);
-+
-+typedef struct vchiq_bulk_struct {
-+ short mode;
-+ short dir;
-+ void *userdata;
-+ VCHI_MEM_HANDLE_T handle;
-+ void *data;
-+ int size;
-+ void *remote_data;
-+ int remote_size;
-+ int actual;
-+} VCHIQ_BULK_T;
-+
-+typedef struct vchiq_bulk_queue_struct {
-+ int local_insert; /* Where to insert the next local bulk */
-+ int remote_insert; /* Where to insert the next remote bulk (master) */
-+ int process; /* Bulk to transfer next */
-+ int remote_notify; /* Bulk to notify the remote client of next (mstr) */
-+ int remove; /* Bulk to notify the local client of, and remove,
-+ ** next */
-+ VCHIQ_BULK_T bulks[VCHIQ_NUM_SERVICE_BULKS];
-+} VCHIQ_BULK_QUEUE_T;
-+
-+typedef struct remote_event_struct {
-+ int armed;
-+ int fired;
-+ struct semaphore *event;
-+} REMOTE_EVENT_T;
-+
-+typedef struct opaque_platform_state_t *VCHIQ_PLATFORM_STATE_T;
-+
-+typedef struct vchiq_state_struct VCHIQ_STATE_T;
-+
-+typedef struct vchiq_slot_struct {
-+ char data[VCHIQ_SLOT_SIZE];
-+} VCHIQ_SLOT_T;
-+
-+typedef struct vchiq_slot_info_struct {
-+ /* Use two counters rather than one to avoid the need for a mutex. */
-+ short use_count;
-+ short release_count;
-+} VCHIQ_SLOT_INFO_T;
-+
-+typedef struct vchiq_service_struct {
-+ VCHIQ_SERVICE_BASE_T base;
-+ VCHIQ_SERVICE_HANDLE_T handle;
-+ unsigned int ref_count;
-+ int srvstate;
-+ VCHIQ_USERDATA_TERM_T userdata_term;
-+ unsigned int localport;
-+ unsigned int remoteport;
-+ int public_fourcc;
-+ int client_id;
-+ char auto_close;
-+ char sync;
-+ char closing;
-+ char trace;
-+ atomic_t poll_flags;
-+ short version;
-+ short version_min;
-+ short peer_version;
-+
-+ VCHIQ_STATE_T *state;
-+ VCHIQ_INSTANCE_T instance;
-+
-+ int service_use_count;
-+
-+ VCHIQ_BULK_QUEUE_T bulk_tx;
-+ VCHIQ_BULK_QUEUE_T bulk_rx;
-+
-+ struct semaphore remove_event;
-+ struct semaphore bulk_remove_event;
-+ struct mutex bulk_mutex;
-+
-+ struct service_stats_struct {
-+ int quota_stalls;
-+ int slot_stalls;
-+ int bulk_stalls;
-+ int error_count;
-+ int ctrl_tx_count;
-+ int ctrl_rx_count;
-+ int bulk_tx_count;
-+ int bulk_rx_count;
-+ int bulk_aborted_count;
-+ uint64_t ctrl_tx_bytes;
-+ uint64_t ctrl_rx_bytes;
-+ uint64_t bulk_tx_bytes;
-+ uint64_t bulk_rx_bytes;
-+ } stats;
-+} VCHIQ_SERVICE_T;
-+
-+/* The quota information is outside VCHIQ_SERVICE_T so that it can be
-+ statically allocated, since for accounting reasons a service's slot
-+ usage is carried over between users of the same port number.
-+ */
-+typedef struct vchiq_service_quota_struct {
-+ unsigned short slot_quota;
-+ unsigned short slot_use_count;
-+ unsigned short message_quota;
-+ unsigned short message_use_count;
-+ struct semaphore quota_event;
-+ int previous_tx_index;
-+} VCHIQ_SERVICE_QUOTA_T;
-+
-+typedef struct vchiq_shared_state_struct {
-+
-+ /* A non-zero value here indicates that the content is valid. */
-+ int initialised;
-+
-+ /* The first and last (inclusive) slots allocated to the owner. */
-+ int slot_first;
-+ int slot_last;
-+
-+ /* The slot allocated to synchronous messages from the owner. */
-+ int slot_sync;
-+
-+ /* Signalling this event indicates that owner's slot handler thread
-+ ** should run. */
-+ REMOTE_EVENT_T trigger;
-+
-+ /* Indicates the byte position within the stream where the next message
-+ ** will be written. The least significant bits are an index into the
-+ ** slot. The next bits are the index of the slot in slot_queue. */
-+ int tx_pos;
-+
-+ /* This event should be signalled when a slot is recycled. */
-+ REMOTE_EVENT_T recycle;
-+
-+ /* The slot_queue index where the next recycled slot will be written. */
-+ int slot_queue_recycle;
-+
-+ /* This event should be signalled when a synchronous message is sent. */
-+ REMOTE_EVENT_T sync_trigger;
-+
-+ /* This event should be signalled when a synchronous message has been
-+ ** released. */
-+ REMOTE_EVENT_T sync_release;
-+
-+ /* A circular buffer of slot indexes. */
-+ int slot_queue[VCHIQ_MAX_SLOTS_PER_SIDE];
-+
-+ /* Debugging state */
-+ int debug[DEBUG_MAX];
-+} VCHIQ_SHARED_STATE_T;
-+
-+typedef struct vchiq_slot_zero_struct {
-+ int magic;
-+ short version;
-+ short version_min;
-+ int slot_zero_size;
-+ int slot_size;
-+ int max_slots;
-+ int max_slots_per_side;
-+ int platform_data[2];
-+ VCHIQ_SHARED_STATE_T master;
-+ VCHIQ_SHARED_STATE_T slave;
-+ VCHIQ_SLOT_INFO_T slots[VCHIQ_MAX_SLOTS];
-+} VCHIQ_SLOT_ZERO_T;
-+
-+struct vchiq_state_struct {
-+ int id;
-+ int initialised;
-+ VCHIQ_CONNSTATE_T conn_state;
-+ int is_master;
-+ short version_common;
-+
-+ VCHIQ_SHARED_STATE_T *local;
-+ VCHIQ_SHARED_STATE_T *remote;
-+ VCHIQ_SLOT_T *slot_data;
-+
-+ unsigned short default_slot_quota;
-+ unsigned short default_message_quota;
-+
-+ /* Event indicating connect message received */
-+ struct semaphore connect;
-+
-+ /* Mutex protecting services */
-+ struct mutex mutex;
-+ VCHIQ_INSTANCE_T *instance;
-+
-+ /* Processes incoming messages */
-+ struct task_struct *slot_handler_thread;
-+
-+ /* Processes recycled slots */
-+ struct task_struct *recycle_thread;
-+
-+ /* Processes synchronous messages */
-+ struct task_struct *sync_thread;
-+
-+ /* Local implementation of the trigger remote event */
-+ struct semaphore trigger_event;
-+
-+ /* Local implementation of the recycle remote event */
-+ struct semaphore recycle_event;
-+
-+ /* Local implementation of the sync trigger remote event */
-+ struct semaphore sync_trigger_event;
-+
-+ /* Local implementation of the sync release remote event */
-+ struct semaphore sync_release_event;
-+
-+ char *tx_data;
-+ char *rx_data;
-+ VCHIQ_SLOT_INFO_T *rx_info;
-+
-+ struct mutex slot_mutex;
-+
-+ struct mutex recycle_mutex;
-+
-+ struct mutex sync_mutex;
-+
-+ struct mutex bulk_transfer_mutex;
-+
-+ /* Indicates the byte position within the stream from where the next
-+ ** message will be read. The least significant bits are an index into
-+ ** the slot.The next bits are the index of the slot in
-+ ** remote->slot_queue. */
-+ int rx_pos;
-+
-+ /* A cached copy of local->tx_pos. Only write to local->tx_pos, and read
-+ from remote->tx_pos. */
-+ int local_tx_pos;
-+
-+ /* The slot_queue index of the slot to become available next. */
-+ int slot_queue_available;
-+
-+ /* A flag to indicate if any poll has been requested */
-+ int poll_needed;
-+
-+ /* Ths index of the previous slot used for data messages. */
-+ int previous_data_index;
-+
-+ /* The number of slots occupied by data messages. */
-+ unsigned short data_use_count;
-+
-+ /* The maximum number of slots to be occupied by data messages. */
-+ unsigned short data_quota;
-+
-+ /* An array of bit sets indicating which services must be polled. */
-+ atomic_t poll_services[BITSET_SIZE(VCHIQ_MAX_SERVICES)];
-+
-+ /* The number of the first unused service */
-+ int unused_service;
-+
-+ /* Signalled when a free slot becomes available. */
-+ struct semaphore slot_available_event;
-+
-+ struct semaphore slot_remove_event;
-+
-+ /* Signalled when a free data slot becomes available. */
-+ struct semaphore data_quota_event;
-+
-+ /* Incremented when there are bulk transfers which cannot be processed
-+ * whilst paused and must be processed on resume */
-+ int deferred_bulks;
-+
-+ struct state_stats_struct {
-+ int slot_stalls;
-+ int data_stalls;
-+ int ctrl_tx_count;
-+ int ctrl_rx_count;
-+ int error_count;
-+ } stats;
-+
-+ VCHIQ_SERVICE_T * services[VCHIQ_MAX_SERVICES];
-+ VCHIQ_SERVICE_QUOTA_T service_quotas[VCHIQ_MAX_SERVICES];
-+ VCHIQ_SLOT_INFO_T slot_info[VCHIQ_MAX_SLOTS];
-+
-+ VCHIQ_PLATFORM_STATE_T platform_state;
-+};
-+
-+struct bulk_waiter {
-+ VCHIQ_BULK_T *bulk;
-+ struct semaphore event;
-+ int actual;
-+};
-+
-+extern spinlock_t bulk_waiter_spinlock;
-+
-+extern int vchiq_core_log_level;
-+extern int vchiq_core_msg_log_level;
-+extern int vchiq_sync_log_level;
-+
-+extern VCHIQ_STATE_T *vchiq_states[VCHIQ_MAX_STATES];
-+
-+extern const char *
-+get_conn_state_name(VCHIQ_CONNSTATE_T conn_state);
-+
-+extern VCHIQ_SLOT_ZERO_T *
-+vchiq_init_slots(void *mem_base, int mem_size);
-+
-+extern VCHIQ_STATUS_T
-+vchiq_init_state(VCHIQ_STATE_T *state, VCHIQ_SLOT_ZERO_T *slot_zero,
-+ int is_master);
-+
-+extern VCHIQ_STATUS_T
-+vchiq_connect_internal(VCHIQ_STATE_T *state, VCHIQ_INSTANCE_T instance);
-+
-+extern VCHIQ_SERVICE_T *
-+vchiq_add_service_internal(VCHIQ_STATE_T *state,
-+ const VCHIQ_SERVICE_PARAMS_T *params, int srvstate,
-+ VCHIQ_INSTANCE_T instance, VCHIQ_USERDATA_TERM_T userdata_term);
-+
-+extern VCHIQ_STATUS_T
-+vchiq_open_service_internal(VCHIQ_SERVICE_T *service, int client_id);
-+
-+extern VCHIQ_STATUS_T
-+vchiq_close_service_internal(VCHIQ_SERVICE_T *service, int close_recvd);
-+
-+extern void
-+vchiq_terminate_service_internal(VCHIQ_SERVICE_T *service);
-+
-+extern void
-+vchiq_free_service_internal(VCHIQ_SERVICE_T *service);
-+
-+extern VCHIQ_STATUS_T
-+vchiq_shutdown_internal(VCHIQ_STATE_T *state, VCHIQ_INSTANCE_T instance);
-+
-+extern VCHIQ_STATUS_T
-+vchiq_pause_internal(VCHIQ_STATE_T *state);
-+
-+extern VCHIQ_STATUS_T
-+vchiq_resume_internal(VCHIQ_STATE_T *state);
-+
-+extern void
-+remote_event_pollall(VCHIQ_STATE_T *state);
-+
-+extern VCHIQ_STATUS_T
-+vchiq_bulk_transfer(VCHIQ_SERVICE_HANDLE_T handle,
-+ VCHI_MEM_HANDLE_T memhandle, void *offset, int size, void *userdata,
-+ VCHIQ_BULK_MODE_T mode, VCHIQ_BULK_DIR_T dir);
-+
-+extern void
-+vchiq_dump_state(void *dump_context, VCHIQ_STATE_T *state);
-+
-+extern void
-+vchiq_dump_service_state(void *dump_context, VCHIQ_SERVICE_T *service);
-+
-+extern void
-+vchiq_loud_error_header(void);
-+
-+extern void
-+vchiq_loud_error_footer(void);
-+
-+extern void
-+request_poll(VCHIQ_STATE_T *state, VCHIQ_SERVICE_T *service, int poll_type);
-+
-+static inline VCHIQ_SERVICE_T *
-+handle_to_service(VCHIQ_SERVICE_HANDLE_T handle)
-+{
-+ VCHIQ_STATE_T *state = vchiq_states[(handle / VCHIQ_MAX_SERVICES) &
-+ (VCHIQ_MAX_STATES - 1)];
-+ if (!state)
-+ return NULL;
-+
-+ return state->services[handle & (VCHIQ_MAX_SERVICES - 1)];
-+}
-+
-+extern VCHIQ_SERVICE_T *
-+find_service_by_handle(VCHIQ_SERVICE_HANDLE_T handle);
-+
-+extern VCHIQ_SERVICE_T *
-+find_service_by_port(VCHIQ_STATE_T *state, int localport);
-+
-+extern VCHIQ_SERVICE_T *
-+find_service_for_instance(VCHIQ_INSTANCE_T instance,
-+ VCHIQ_SERVICE_HANDLE_T handle);
-+
-+extern VCHIQ_SERVICE_T *
-+find_closed_service_for_instance(VCHIQ_INSTANCE_T instance,
-+ VCHIQ_SERVICE_HANDLE_T handle);
-+
-+extern VCHIQ_SERVICE_T *
-+next_service_by_instance(VCHIQ_STATE_T *state, VCHIQ_INSTANCE_T instance,
-+ int *pidx);
-+
-+extern void
-+lock_service(VCHIQ_SERVICE_T *service);
-+
-+extern void
-+unlock_service(VCHIQ_SERVICE_T *service);
-+
-+/* The following functions are called from vchiq_core, and external
-+** implementations must be provided. */
-+
-+extern VCHIQ_STATUS_T
-+vchiq_prepare_bulk_data(VCHIQ_BULK_T *bulk,
-+ VCHI_MEM_HANDLE_T memhandle, void *offset, int size, int dir);
-+
-+extern void
-+vchiq_transfer_bulk(VCHIQ_BULK_T *bulk);
-+
-+extern void
-+vchiq_complete_bulk(VCHIQ_BULK_T *bulk);
-+
-+extern VCHIQ_STATUS_T
-+vchiq_copy_from_user(void *dst, const void *src, int size);
-+
-+extern void
-+remote_event_signal(REMOTE_EVENT_T *event);
-+
-+void
-+vchiq_platform_check_suspend(VCHIQ_STATE_T *state);
-+
-+extern void
-+vchiq_platform_paused(VCHIQ_STATE_T *state);
-+
-+extern VCHIQ_STATUS_T
-+vchiq_platform_resume(VCHIQ_STATE_T *state);
-+
-+extern void
-+vchiq_platform_resumed(VCHIQ_STATE_T *state);
-+
-+extern void
-+vchiq_dump(void *dump_context, const char *str, int len);
-+
-+extern void
-+vchiq_dump_platform_state(void *dump_context);
-+
-+extern void
-+vchiq_dump_platform_instances(void *dump_context);
-+
-+extern void
-+vchiq_dump_platform_service_state(void *dump_context,
-+ VCHIQ_SERVICE_T *service);
-+
-+extern VCHIQ_STATUS_T
-+vchiq_use_service_internal(VCHIQ_SERVICE_T *service);
-+
-+extern VCHIQ_STATUS_T
-+vchiq_release_service_internal(VCHIQ_SERVICE_T *service);
-+
-+extern void
-+vchiq_on_remote_use(VCHIQ_STATE_T *state);
-+
-+extern void
-+vchiq_on_remote_release(VCHIQ_STATE_T *state);
-+
-+extern VCHIQ_STATUS_T
-+vchiq_platform_init_state(VCHIQ_STATE_T *state);
-+
-+extern VCHIQ_STATUS_T
-+vchiq_check_service(VCHIQ_SERVICE_T *service);
-+
-+extern void
-+vchiq_on_remote_use_active(VCHIQ_STATE_T *state);
-+
-+extern VCHIQ_STATUS_T
-+vchiq_send_remote_use(VCHIQ_STATE_T *state);
-+
-+extern VCHIQ_STATUS_T
-+vchiq_send_remote_release(VCHIQ_STATE_T *state);
-+
-+extern VCHIQ_STATUS_T
-+vchiq_send_remote_use_active(VCHIQ_STATE_T *state);
-+
-+extern void
-+vchiq_platform_conn_state_changed(VCHIQ_STATE_T *state,
-+ VCHIQ_CONNSTATE_T oldstate, VCHIQ_CONNSTATE_T newstate);
-+
-+extern void
-+vchiq_platform_handle_timeout(VCHIQ_STATE_T *state);
-+
-+extern void
-+vchiq_set_conn_state(VCHIQ_STATE_T *state, VCHIQ_CONNSTATE_T newstate);
-+
-+
-+extern void
-+vchiq_log_dump_mem(const char *label, uint32_t addr, const void *voidMem,
-+ size_t numBytes);
-+
-+#endif
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_debugfs.c
-@@ -0,0 +1,383 @@
-+/**
-+ * Copyright (c) 2014 Raspberry Pi (Trading) Ltd. All rights reserved.
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+
-+#include <linux/debugfs.h>
-+#include "vchiq_core.h"
-+#include "vchiq_arm.h"
-+#include "vchiq_debugfs.h"
-+
-+#ifdef CONFIG_DEBUG_FS
-+
-+/****************************************************************************
-+*
-+* log category entries
-+*
-+***************************************************************************/
-+#define DEBUGFS_WRITE_BUF_SIZE 256
-+
-+#define VCHIQ_LOG_ERROR_STR "error"
-+#define VCHIQ_LOG_WARNING_STR "warning"
-+#define VCHIQ_LOG_INFO_STR "info"
-+#define VCHIQ_LOG_TRACE_STR "trace"
-+
-+
-+/* Top-level debug info */
-+struct vchiq_debugfs_info {
-+ /* Global 'vchiq' debugfs entry used by all instances */
-+ struct dentry *vchiq_cfg_dir;
-+
-+ /* one entry per client process */
-+ struct dentry *clients;
-+
-+ /* log categories */
-+ struct dentry *log_categories;
-+};
-+
-+static struct vchiq_debugfs_info debugfs_info;
-+
-+/* Log category debugfs entries */
-+struct vchiq_debugfs_log_entry {
-+ const char *name;
-+ int *plevel;
-+ struct dentry *dir;
-+};
-+
-+static struct vchiq_debugfs_log_entry vchiq_debugfs_log_entries[] = {
-+ { "core", &vchiq_core_log_level },
-+ { "msg", &vchiq_core_msg_log_level },
-+ { "sync", &vchiq_sync_log_level },
-+ { "susp", &vchiq_susp_log_level },
-+ { "arm", &vchiq_arm_log_level },
-+};
-+static int n_log_entries =
-+ sizeof(vchiq_debugfs_log_entries)/sizeof(vchiq_debugfs_log_entries[0]);
-+
-+
-+static struct dentry *vchiq_clients_top(void);
-+static struct dentry *vchiq_debugfs_top(void);
-+
-+static int debugfs_log_show(struct seq_file *f, void *offset)
-+{
-+ int *levp = f->private;
-+ char *log_value = NULL;
-+
-+ switch (*levp) {
-+ case VCHIQ_LOG_ERROR:
-+ log_value = VCHIQ_LOG_ERROR_STR;
-+ break;
-+ case VCHIQ_LOG_WARNING:
-+ log_value = VCHIQ_LOG_WARNING_STR;
-+ break;
-+ case VCHIQ_LOG_INFO:
-+ log_value = VCHIQ_LOG_INFO_STR;
-+ break;
-+ case VCHIQ_LOG_TRACE:
-+ log_value = VCHIQ_LOG_TRACE_STR;
-+ break;
-+ default:
-+ break;
-+ }
-+
-+ seq_printf(f, "%s\n", log_value ? log_value : "(null)");
-+
-+ return 0;
-+}
-+
-+static int debugfs_log_open(struct inode *inode, struct file *file)
-+{
-+ return single_open(file, debugfs_log_show, inode->i_private);
-+}
-+
-+static int debugfs_log_write(struct file *file,
-+ const char __user *buffer,
-+ size_t count, loff_t *ppos)
-+{
-+ struct seq_file *f = (struct seq_file *)file->private_data;
-+ int *levp = f->private;
-+ char kbuf[DEBUGFS_WRITE_BUF_SIZE + 1];
-+
-+ memset(kbuf, 0, DEBUGFS_WRITE_BUF_SIZE + 1);
-+ if (count >= DEBUGFS_WRITE_BUF_SIZE)
-+ count = DEBUGFS_WRITE_BUF_SIZE;
-+
-+ if (copy_from_user(kbuf, buffer, count) != 0)
-+ return -EFAULT;
-+ kbuf[count - 1] = 0;
-+
-+ if (strncmp("error", kbuf, strlen("error")) == 0)
-+ *levp = VCHIQ_LOG_ERROR;
-+ else if (strncmp("warning", kbuf, strlen("warning")) == 0)
-+ *levp = VCHIQ_LOG_WARNING;
-+ else if (strncmp("info", kbuf, strlen("info")) == 0)
-+ *levp = VCHIQ_LOG_INFO;
-+ else if (strncmp("trace", kbuf, strlen("trace")) == 0)
-+ *levp = VCHIQ_LOG_TRACE;
-+ else
-+ *levp = VCHIQ_LOG_DEFAULT;
-+
-+ *ppos += count;
-+
-+ return count;
-+}
-+
-+static const struct file_operations debugfs_log_fops = {
-+ .owner = THIS_MODULE,
-+ .open = debugfs_log_open,
-+ .write = debugfs_log_write,
-+ .read = seq_read,
-+ .llseek = seq_lseek,
-+ .release = single_release,
-+};
-+
-+/* create an entry under <debugfs>/vchiq/log for each log category */
-+static int vchiq_debugfs_create_log_entries(struct dentry *top)
-+{
-+ struct dentry *dir;
-+ size_t i;
-+ int ret = 0;
-+ dir = debugfs_create_dir("log", vchiq_debugfs_top());
-+ if (!dir)
-+ return -ENOMEM;
-+ debugfs_info.log_categories = dir;
-+
-+ for (i = 0; i < n_log_entries; i++) {
-+ void *levp = (void *)vchiq_debugfs_log_entries[i].plevel;
-+ dir = debugfs_create_file(vchiq_debugfs_log_entries[i].name,
-+ 0644,
-+ debugfs_info.log_categories,
-+ levp,
-+ &debugfs_log_fops);
-+ if (!dir) {
-+ ret = -ENOMEM;
-+ break;
-+ }
-+
-+ vchiq_debugfs_log_entries[i].dir = dir;
-+ }
-+ return ret;
-+}
-+
-+static int debugfs_usecount_show(struct seq_file *f, void *offset)
-+{
-+ VCHIQ_INSTANCE_T instance = f->private;
-+ int use_count;
-+
-+ use_count = vchiq_instance_get_use_count(instance);
-+ seq_printf(f, "%d\n", use_count);
-+
-+ return 0;
-+}
-+
-+static int debugfs_usecount_open(struct inode *inode, struct file *file)
-+{
-+ return single_open(file, debugfs_usecount_show, inode->i_private);
-+}
-+
-+static const struct file_operations debugfs_usecount_fops = {
-+ .owner = THIS_MODULE,
-+ .open = debugfs_usecount_open,
-+ .read = seq_read,
-+ .llseek = seq_lseek,
-+ .release = single_release,
-+};
-+
-+static int debugfs_trace_show(struct seq_file *f, void *offset)
-+{
-+ VCHIQ_INSTANCE_T instance = f->private;
-+ int trace;
-+
-+ trace = vchiq_instance_get_trace(instance);
-+ seq_printf(f, "%s\n", trace ? "Y" : "N");
-+
-+ return 0;
-+}
-+
-+static int debugfs_trace_open(struct inode *inode, struct file *file)
-+{
-+ return single_open(file, debugfs_trace_show, inode->i_private);
-+}
-+
-+static int debugfs_trace_write(struct file *file,
-+ const char __user *buffer,
-+ size_t count, loff_t *ppos)
-+{
-+ struct seq_file *f = (struct seq_file *)file->private_data;
-+ VCHIQ_INSTANCE_T instance = f->private;
-+ char firstchar;
-+
-+ if (copy_from_user(&firstchar, buffer, 1) != 0)
-+ return -EFAULT;
-+
-+ switch (firstchar) {
-+ case 'Y':
-+ case 'y':
-+ case '1':
-+ vchiq_instance_set_trace(instance, 1);
-+ break;
-+ case 'N':
-+ case 'n':
-+ case '0':
-+ vchiq_instance_set_trace(instance, 0);
-+ break;
-+ default:
-+ break;
-+ }
-+
-+ *ppos += count;
-+
-+ return count;
-+}
-+
-+static const struct file_operations debugfs_trace_fops = {
-+ .owner = THIS_MODULE,
-+ .open = debugfs_trace_open,
-+ .write = debugfs_trace_write,
-+ .read = seq_read,
-+ .llseek = seq_lseek,
-+ .release = single_release,
-+};
-+
-+/* add an instance (process) to the debugfs entries */
-+int vchiq_debugfs_add_instance(VCHIQ_INSTANCE_T instance)
-+{
-+ char pidstr[16];
-+ struct dentry *top, *use_count, *trace;
-+ struct dentry *clients = vchiq_clients_top();
-+
-+ snprintf(pidstr, sizeof(pidstr), "%d",
-+ vchiq_instance_get_pid(instance));
-+
-+ top = debugfs_create_dir(pidstr, clients);
-+ if (!top)
-+ goto fail_top;
-+
-+ use_count = debugfs_create_file("use_count",
-+ 0444, top,
-+ instance,
-+ &debugfs_usecount_fops);
-+ if (!use_count)
-+ goto fail_use_count;
-+
-+ trace = debugfs_create_file("trace",
-+ 0644, top,
-+ instance,
-+ &debugfs_trace_fops);
-+ if (!trace)
-+ goto fail_trace;
-+
-+ vchiq_instance_get_debugfs_node(instance)->dentry = top;
-+
-+ return 0;
-+
-+fail_trace:
-+ debugfs_remove(use_count);
-+fail_use_count:
-+ debugfs_remove(top);
-+fail_top:
-+ return -ENOMEM;
-+}
-+
-+void vchiq_debugfs_remove_instance(VCHIQ_INSTANCE_T instance)
-+{
-+ VCHIQ_DEBUGFS_NODE_T *node = vchiq_instance_get_debugfs_node(instance);
-+ debugfs_remove_recursive(node->dentry);
-+}
-+
-+
-+int vchiq_debugfs_init(void)
-+{
-+ BUG_ON(debugfs_info.vchiq_cfg_dir != NULL);
-+
-+ debugfs_info.vchiq_cfg_dir = debugfs_create_dir("vchiq", NULL);
-+ if (debugfs_info.vchiq_cfg_dir == NULL)
-+ goto fail;
-+
-+ debugfs_info.clients = debugfs_create_dir("clients",
-+ vchiq_debugfs_top());
-+ if (!debugfs_info.clients)
-+ goto fail;
-+
-+ if (vchiq_debugfs_create_log_entries(vchiq_debugfs_top()) != 0)
-+ goto fail;
-+
-+ return 0;
-+
-+fail:
-+ vchiq_debugfs_deinit();
-+ vchiq_log_error(vchiq_arm_log_level,
-+ "%s: failed to create debugfs directory",
-+ __func__);
-+
-+ return -ENOMEM;
-+}
-+
-+/* remove all the debugfs entries */
-+void vchiq_debugfs_deinit(void)
-+{
-+ debugfs_remove_recursive(vchiq_debugfs_top());
-+}
-+
-+static struct dentry *vchiq_clients_top(void)
-+{
-+ return debugfs_info.clients;
-+}
-+
-+static struct dentry *vchiq_debugfs_top(void)
-+{
-+ BUG_ON(debugfs_info.vchiq_cfg_dir == NULL);
-+ return debugfs_info.vchiq_cfg_dir;
-+}
-+
-+#else /* CONFIG_DEBUG_FS */
-+
-+int vchiq_debugfs_init(void)
-+{
-+ return 0;
-+}
-+
-+void vchiq_debugfs_deinit(void)
-+{
-+}
-+
-+int vchiq_debugfs_add_instance(VCHIQ_INSTANCE_T instance)
-+{
-+ return 0;
-+}
-+
-+void vchiq_debugfs_remove_instance(VCHIQ_INSTANCE_T instance)
-+{
-+}
-+
-+#endif /* CONFIG_DEBUG_FS */
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_debugfs.h
-@@ -0,0 +1,52 @@
-+/**
-+ * Copyright (c) 2014 Raspberry Pi (Trading) Ltd. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#ifndef VCHIQ_DEBUGFS_H
-+#define VCHIQ_DEBUGFS_H
-+
-+#include "vchiq_core.h"
-+
-+typedef struct vchiq_debugfs_node_struct
-+{
-+ struct dentry *dentry;
-+} VCHIQ_DEBUGFS_NODE_T;
-+
-+int vchiq_debugfs_init(void);
-+
-+void vchiq_debugfs_deinit(void);
-+
-+int vchiq_debugfs_add_instance(VCHIQ_INSTANCE_T instance);
-+
-+void vchiq_debugfs_remove_instance(VCHIQ_INSTANCE_T instance);
-+
-+#endif /* VCHIQ_DEBUGFS_H */
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_genversion
-@@ -0,0 +1,87 @@
-+#!/usr/bin/perl -w
-+
-+use strict;
-+
-+#
-+# Generate a version from available information
-+#
-+
-+my $prefix = shift @ARGV;
-+my $root = shift @ARGV;
-+
-+
-+if ( not defined $root ) {
-+ die "usage: $0 prefix root-dir\n";
-+}
-+
-+if ( ! -d $root ) {
-+ die "root directory $root not found\n";
-+}
-+
-+my $version = "unknown";
-+my $tainted = "";
-+
-+if ( -d "$root/.git" ) {
-+ # attempt to work out git version. only do so
-+ # on a linux build host, as cygwin builds are
-+ # already slow enough
-+
-+ if ( -f "/usr/bin/git" || -f "/usr/local/bin/git" ) {
-+ if (not open(F, "git --git-dir $root/.git rev-parse --verify HEAD|")) {
-+ $version = "no git version";
-+ }
-+ else {
-+ $version = <F>;
-+ $version =~ s/[ \r\n]*$//; # chomp may not be enough (cygwin).
-+ $version =~ s/^[ \r\n]*//; # chomp may not be enough (cygwin).
-+ }
-+
-+ if (open(G, "git --git-dir $root/.git status --porcelain|")) {
-+ $tainted = <G>;
-+ $tainted =~ s/[ \r\n]*$//; # chomp may not be enough (cygwin).
-+ $tainted =~ s/^[ \r\n]*//; # chomp may not be enough (cygwin).
-+ if (length $tainted) {
-+ $version = join ' ', $version, "(tainted)";
-+ }
-+ else {
-+ $version = join ' ', $version, "(clean)";
-+ }
-+ }
-+ }
-+}
-+
-+my $hostname = `hostname`;
-+$hostname =~ s/[ \r\n]*$//; # chomp may not be enough (cygwin).
-+$hostname =~ s/^[ \r\n]*//; # chomp may not be enough (cygwin).
-+
-+
-+print STDERR "Version $version\n";
-+print <<EOF;
-+#include "${prefix}_build_info.h"
-+#include <linux/broadcom/vc_debug_sym.h>
-+
-+VC_DEBUG_DECLARE_STRING_VAR( ${prefix}_build_hostname, "$hostname" );
-+VC_DEBUG_DECLARE_STRING_VAR( ${prefix}_build_version, "$version" );
-+VC_DEBUG_DECLARE_STRING_VAR( ${prefix}_build_time, __TIME__ );
-+VC_DEBUG_DECLARE_STRING_VAR( ${prefix}_build_date, __DATE__ );
-+
-+const char *vchiq_get_build_hostname( void )
-+{
-+ return vchiq_build_hostname;
-+}
-+
-+const char *vchiq_get_build_version( void )
-+{
-+ return vchiq_build_version;
-+}
-+
-+const char *vchiq_get_build_date( void )
-+{
-+ return vchiq_build_date;
-+}
-+
-+const char *vchiq_get_build_time( void )
-+{
-+ return vchiq_build_time;
-+}
-+EOF
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_if.h
-@@ -0,0 +1,189 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#ifndef VCHIQ_IF_H
-+#define VCHIQ_IF_H
-+
-+#include "interface/vchi/vchi_mh.h"
-+
-+#define VCHIQ_SERVICE_HANDLE_INVALID 0
-+
-+#define VCHIQ_SLOT_SIZE 4096
-+#define VCHIQ_MAX_MSG_SIZE (VCHIQ_SLOT_SIZE - sizeof(VCHIQ_HEADER_T))
-+#define VCHIQ_CHANNEL_SIZE VCHIQ_MAX_MSG_SIZE /* For backwards compatibility */
-+
-+#define VCHIQ_MAKE_FOURCC(x0, x1, x2, x3) \
-+ (((x0) << 24) | ((x1) << 16) | ((x2) << 8) | (x3))
-+#define VCHIQ_GET_SERVICE_USERDATA(service) vchiq_get_service_userdata(service)
-+#define VCHIQ_GET_SERVICE_FOURCC(service) vchiq_get_service_fourcc(service)
-+
-+typedef enum {
-+ VCHIQ_SERVICE_OPENED, /* service, -, - */
-+ VCHIQ_SERVICE_CLOSED, /* service, -, - */
-+ VCHIQ_MESSAGE_AVAILABLE, /* service, header, - */
-+ VCHIQ_BULK_TRANSMIT_DONE, /* service, -, bulk_userdata */
-+ VCHIQ_BULK_RECEIVE_DONE, /* service, -, bulk_userdata */
-+ VCHIQ_BULK_TRANSMIT_ABORTED, /* service, -, bulk_userdata */
-+ VCHIQ_BULK_RECEIVE_ABORTED /* service, -, bulk_userdata */
-+} VCHIQ_REASON_T;
-+
-+typedef enum {
-+ VCHIQ_ERROR = -1,
-+ VCHIQ_SUCCESS = 0,
-+ VCHIQ_RETRY = 1
-+} VCHIQ_STATUS_T;
-+
-+typedef enum {
-+ VCHIQ_BULK_MODE_CALLBACK,
-+ VCHIQ_BULK_MODE_BLOCKING,
-+ VCHIQ_BULK_MODE_NOCALLBACK,
-+ VCHIQ_BULK_MODE_WAITING /* Reserved for internal use */
-+} VCHIQ_BULK_MODE_T;
-+
-+typedef enum {
-+ VCHIQ_SERVICE_OPTION_AUTOCLOSE,
-+ VCHIQ_SERVICE_OPTION_SLOT_QUOTA,
-+ VCHIQ_SERVICE_OPTION_MESSAGE_QUOTA,
-+ VCHIQ_SERVICE_OPTION_SYNCHRONOUS,
-+ VCHIQ_SERVICE_OPTION_TRACE
-+} VCHIQ_SERVICE_OPTION_T;
-+
-+typedef struct vchiq_header_struct {
-+ /* The message identifier - opaque to applications. */
-+ int msgid;
-+
-+ /* Size of message data. */
-+ unsigned int size;
-+
-+ char data[0]; /* message */
-+} VCHIQ_HEADER_T;
-+
-+typedef struct {
-+ const void *data;
-+ unsigned int size;
-+} VCHIQ_ELEMENT_T;
-+
-+typedef unsigned int VCHIQ_SERVICE_HANDLE_T;
-+
-+typedef VCHIQ_STATUS_T (*VCHIQ_CALLBACK_T)(VCHIQ_REASON_T, VCHIQ_HEADER_T *,
-+ VCHIQ_SERVICE_HANDLE_T, void *);
-+
-+typedef struct vchiq_service_base_struct {
-+ int fourcc;
-+ VCHIQ_CALLBACK_T callback;
-+ void *userdata;
-+} VCHIQ_SERVICE_BASE_T;
-+
-+typedef struct vchiq_service_params_struct {
-+ int fourcc;
-+ VCHIQ_CALLBACK_T callback;
-+ void *userdata;
-+ short version; /* Increment for non-trivial changes */
-+ short version_min; /* Update for incompatible changes */
-+} VCHIQ_SERVICE_PARAMS_T;
-+
-+typedef struct vchiq_config_struct {
-+ unsigned int max_msg_size;
-+ unsigned int bulk_threshold; /* The message size above which it
-+ is better to use a bulk transfer
-+ (<= max_msg_size) */
-+ unsigned int max_outstanding_bulks;
-+ unsigned int max_services;
-+ short version; /* The version of VCHIQ */
-+ short version_min; /* The minimum compatible version of VCHIQ */
-+} VCHIQ_CONFIG_T;
-+
-+typedef struct vchiq_instance_struct *VCHIQ_INSTANCE_T;
-+typedef void (*VCHIQ_REMOTE_USE_CALLBACK_T)(void *cb_arg);
-+
-+extern VCHIQ_STATUS_T vchiq_initialise(VCHIQ_INSTANCE_T *pinstance);
-+extern VCHIQ_STATUS_T vchiq_shutdown(VCHIQ_INSTANCE_T instance);
-+extern VCHIQ_STATUS_T vchiq_connect(VCHIQ_INSTANCE_T instance);
-+extern VCHIQ_STATUS_T vchiq_add_service(VCHIQ_INSTANCE_T instance,
-+ const VCHIQ_SERVICE_PARAMS_T *params,
-+ VCHIQ_SERVICE_HANDLE_T *pservice);
-+extern VCHIQ_STATUS_T vchiq_open_service(VCHIQ_INSTANCE_T instance,
-+ const VCHIQ_SERVICE_PARAMS_T *params,
-+ VCHIQ_SERVICE_HANDLE_T *pservice);
-+extern VCHIQ_STATUS_T vchiq_close_service(VCHIQ_SERVICE_HANDLE_T service);
-+extern VCHIQ_STATUS_T vchiq_remove_service(VCHIQ_SERVICE_HANDLE_T service);
-+extern VCHIQ_STATUS_T vchiq_use_service(VCHIQ_SERVICE_HANDLE_T service);
-+extern VCHIQ_STATUS_T vchiq_use_service_no_resume(
-+ VCHIQ_SERVICE_HANDLE_T service);
-+extern VCHIQ_STATUS_T vchiq_release_service(VCHIQ_SERVICE_HANDLE_T service);
-+
-+extern VCHIQ_STATUS_T vchiq_queue_message(VCHIQ_SERVICE_HANDLE_T service,
-+ const VCHIQ_ELEMENT_T *elements, unsigned int count);
-+extern void vchiq_release_message(VCHIQ_SERVICE_HANDLE_T service,
-+ VCHIQ_HEADER_T *header);
-+extern VCHIQ_STATUS_T vchiq_queue_bulk_transmit(VCHIQ_SERVICE_HANDLE_T service,
-+ const void *data, unsigned int size, void *userdata);
-+extern VCHIQ_STATUS_T vchiq_queue_bulk_receive(VCHIQ_SERVICE_HANDLE_T service,
-+ void *data, unsigned int size, void *userdata);
-+extern VCHIQ_STATUS_T vchiq_queue_bulk_transmit_handle(
-+ VCHIQ_SERVICE_HANDLE_T service, VCHI_MEM_HANDLE_T handle,
-+ const void *offset, unsigned int size, void *userdata);
-+extern VCHIQ_STATUS_T vchiq_queue_bulk_receive_handle(
-+ VCHIQ_SERVICE_HANDLE_T service, VCHI_MEM_HANDLE_T handle,
-+ void *offset, unsigned int size, void *userdata);
-+extern VCHIQ_STATUS_T vchiq_bulk_transmit(VCHIQ_SERVICE_HANDLE_T service,
-+ const void *data, unsigned int size, void *userdata,
-+ VCHIQ_BULK_MODE_T mode);
-+extern VCHIQ_STATUS_T vchiq_bulk_receive(VCHIQ_SERVICE_HANDLE_T service,
-+ void *data, unsigned int size, void *userdata,
-+ VCHIQ_BULK_MODE_T mode);
-+extern VCHIQ_STATUS_T vchiq_bulk_transmit_handle(VCHIQ_SERVICE_HANDLE_T service,
-+ VCHI_MEM_HANDLE_T handle, const void *offset, unsigned int size,
-+ void *userdata, VCHIQ_BULK_MODE_T mode);
-+extern VCHIQ_STATUS_T vchiq_bulk_receive_handle(VCHIQ_SERVICE_HANDLE_T service,
-+ VCHI_MEM_HANDLE_T handle, void *offset, unsigned int size,
-+ void *userdata, VCHIQ_BULK_MODE_T mode);
-+extern int vchiq_get_client_id(VCHIQ_SERVICE_HANDLE_T service);
-+extern void *vchiq_get_service_userdata(VCHIQ_SERVICE_HANDLE_T service);
-+extern int vchiq_get_service_fourcc(VCHIQ_SERVICE_HANDLE_T service);
-+extern VCHIQ_STATUS_T vchiq_get_config(VCHIQ_INSTANCE_T instance,
-+ int config_size, VCHIQ_CONFIG_T *pconfig);
-+extern VCHIQ_STATUS_T vchiq_set_service_option(VCHIQ_SERVICE_HANDLE_T service,
-+ VCHIQ_SERVICE_OPTION_T option, int value);
-+
-+extern VCHIQ_STATUS_T vchiq_remote_use(VCHIQ_INSTANCE_T instance,
-+ VCHIQ_REMOTE_USE_CALLBACK_T callback, void *cb_arg);
-+extern VCHIQ_STATUS_T vchiq_remote_release(VCHIQ_INSTANCE_T instance);
-+
-+extern VCHIQ_STATUS_T vchiq_dump_phys_mem(VCHIQ_SERVICE_HANDLE_T service,
-+ void *ptr, size_t num_bytes);
-+
-+extern VCHIQ_STATUS_T vchiq_get_peer_version(VCHIQ_SERVICE_HANDLE_T handle,
-+ short *peer_version);
-+
-+#endif /* VCHIQ_IF_H */
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_ioctl.h
-@@ -0,0 +1,131 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#ifndef VCHIQ_IOCTLS_H
-+#define VCHIQ_IOCTLS_H
-+
-+#include <linux/ioctl.h>
-+#include "vchiq_if.h"
-+
-+#define VCHIQ_IOC_MAGIC 0xc4
-+#define VCHIQ_INVALID_HANDLE (~0)
-+
-+typedef struct {
-+ VCHIQ_SERVICE_PARAMS_T params;
-+ int is_open;
-+ int is_vchi;
-+ unsigned int handle; /* OUT */
-+} VCHIQ_CREATE_SERVICE_T;
-+
-+typedef struct {
-+ unsigned int handle;
-+ unsigned int count;
-+ const VCHIQ_ELEMENT_T *elements;
-+} VCHIQ_QUEUE_MESSAGE_T;
-+
-+typedef struct {
-+ unsigned int handle;
-+ void *data;
-+ unsigned int size;
-+ void *userdata;
-+ VCHIQ_BULK_MODE_T mode;
-+} VCHIQ_QUEUE_BULK_TRANSFER_T;
-+
-+typedef struct {
-+ VCHIQ_REASON_T reason;
-+ VCHIQ_HEADER_T *header;
-+ void *service_userdata;
-+ void *bulk_userdata;
-+} VCHIQ_COMPLETION_DATA_T;
-+
-+typedef struct {
-+ unsigned int count;
-+ VCHIQ_COMPLETION_DATA_T *buf;
-+ unsigned int msgbufsize;
-+ unsigned int msgbufcount; /* IN/OUT */
-+ void **msgbufs;
-+} VCHIQ_AWAIT_COMPLETION_T;
-+
-+typedef struct {
-+ unsigned int handle;
-+ int blocking;
-+ unsigned int bufsize;
-+ void *buf;
-+} VCHIQ_DEQUEUE_MESSAGE_T;
-+
-+typedef struct {
-+ unsigned int config_size;
-+ VCHIQ_CONFIG_T *pconfig;
-+} VCHIQ_GET_CONFIG_T;
-+
-+typedef struct {
-+ unsigned int handle;
-+ VCHIQ_SERVICE_OPTION_T option;
-+ int value;
-+} VCHIQ_SET_SERVICE_OPTION_T;
-+
-+typedef struct {
-+ void *virt_addr;
-+ size_t num_bytes;
-+} VCHIQ_DUMP_MEM_T;
-+
-+#define VCHIQ_IOC_CONNECT _IO(VCHIQ_IOC_MAGIC, 0)
-+#define VCHIQ_IOC_SHUTDOWN _IO(VCHIQ_IOC_MAGIC, 1)
-+#define VCHIQ_IOC_CREATE_SERVICE \
-+ _IOWR(VCHIQ_IOC_MAGIC, 2, VCHIQ_CREATE_SERVICE_T)
-+#define VCHIQ_IOC_REMOVE_SERVICE _IO(VCHIQ_IOC_MAGIC, 3)
-+#define VCHIQ_IOC_QUEUE_MESSAGE \
-+ _IOW(VCHIQ_IOC_MAGIC, 4, VCHIQ_QUEUE_MESSAGE_T)
-+#define VCHIQ_IOC_QUEUE_BULK_TRANSMIT \
-+ _IOWR(VCHIQ_IOC_MAGIC, 5, VCHIQ_QUEUE_BULK_TRANSFER_T)
-+#define VCHIQ_IOC_QUEUE_BULK_RECEIVE \
-+ _IOWR(VCHIQ_IOC_MAGIC, 6, VCHIQ_QUEUE_BULK_TRANSFER_T)
-+#define VCHIQ_IOC_AWAIT_COMPLETION \
-+ _IOWR(VCHIQ_IOC_MAGIC, 7, VCHIQ_AWAIT_COMPLETION_T)
-+#define VCHIQ_IOC_DEQUEUE_MESSAGE \
-+ _IOWR(VCHIQ_IOC_MAGIC, 8, VCHIQ_DEQUEUE_MESSAGE_T)
-+#define VCHIQ_IOC_GET_CLIENT_ID _IO(VCHIQ_IOC_MAGIC, 9)
-+#define VCHIQ_IOC_GET_CONFIG \
-+ _IOWR(VCHIQ_IOC_MAGIC, 10, VCHIQ_GET_CONFIG_T)
-+#define VCHIQ_IOC_CLOSE_SERVICE _IO(VCHIQ_IOC_MAGIC, 11)
-+#define VCHIQ_IOC_USE_SERVICE _IO(VCHIQ_IOC_MAGIC, 12)
-+#define VCHIQ_IOC_RELEASE_SERVICE _IO(VCHIQ_IOC_MAGIC, 13)
-+#define VCHIQ_IOC_SET_SERVICE_OPTION \
-+ _IOW(VCHIQ_IOC_MAGIC, 14, VCHIQ_SET_SERVICE_OPTION_T)
-+#define VCHIQ_IOC_DUMP_PHYS_MEM \
-+ _IOW(VCHIQ_IOC_MAGIC, 15, VCHIQ_DUMP_MEM_T)
-+#define VCHIQ_IOC_LIB_VERSION _IO(VCHIQ_IOC_MAGIC, 16)
-+#define VCHIQ_IOC_CLOSE_DELIVERED _IO(VCHIQ_IOC_MAGIC, 17)
-+#define VCHIQ_IOC_MAX 17
-+
-+#endif
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_kern_lib.c
-@@ -0,0 +1,458 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+/* ---- Include Files ---------------------------------------------------- */
-+
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+#include <linux/mutex.h>
-+
-+#include "vchiq_core.h"
-+#include "vchiq_arm.h"
-+#include "vchiq_killable.h"
-+
-+/* ---- Public Variables ------------------------------------------------- */
-+
-+/* ---- Private Constants and Types -------------------------------------- */
-+
-+struct bulk_waiter_node {
-+ struct bulk_waiter bulk_waiter;
-+ int pid;
-+ struct list_head list;
-+};
-+
-+struct vchiq_instance_struct {
-+ VCHIQ_STATE_T *state;
-+
-+ int connected;
-+
-+ struct list_head bulk_waiter_list;
-+ struct mutex bulk_waiter_list_mutex;
-+};
-+
-+static VCHIQ_STATUS_T
-+vchiq_blocking_bulk_transfer(VCHIQ_SERVICE_HANDLE_T handle, void *data,
-+ unsigned int size, VCHIQ_BULK_DIR_T dir);
-+
-+/****************************************************************************
-+*
-+* vchiq_initialise
-+*
-+***************************************************************************/
-+#define VCHIQ_INIT_RETRIES 10
-+VCHIQ_STATUS_T vchiq_initialise(VCHIQ_INSTANCE_T *instanceOut)
-+{
-+ VCHIQ_STATUS_T status = VCHIQ_ERROR;
-+ VCHIQ_STATE_T *state;
-+ VCHIQ_INSTANCE_T instance = NULL;
-+ int i;
-+
-+ vchiq_log_trace(vchiq_core_log_level, "%s called", __func__);
-+
-+ /* VideoCore may not be ready due to boot up timing.
-+ It may never be ready if kernel and firmware are mismatched, so don't block forever. */
-+ for (i=0; i<VCHIQ_INIT_RETRIES; i++) {
-+ state = vchiq_get_state();
-+ if (state)
-+ break;
-+ udelay(500);
-+ }
-+ if (i==VCHIQ_INIT_RETRIES) {
-+ vchiq_log_error(vchiq_core_log_level,
-+ "%s: videocore not initialized\n", __func__);
-+ goto failed;
-+ } else if (i>0) {
-+ vchiq_log_warning(vchiq_core_log_level,
-+ "%s: videocore initialized after %d retries\n", __func__, i);
-+ }
-+
-+ instance = kzalloc(sizeof(*instance), GFP_KERNEL);
-+ if (!instance) {
-+ vchiq_log_error(vchiq_core_log_level,
-+ "%s: error allocating vchiq instance\n", __func__);
-+ goto failed;
-+ }
-+
-+ instance->connected = 0;
-+ instance->state = state;
-+ mutex_init(&instance->bulk_waiter_list_mutex);
-+ INIT_LIST_HEAD(&instance->bulk_waiter_list);
-+
-+ *instanceOut = instance;
-+
-+ status = VCHIQ_SUCCESS;
-+
-+failed:
-+ vchiq_log_trace(vchiq_core_log_level,
-+ "%s(%p): returning %d", __func__, instance, status);
-+
-+ return status;
-+}
-+EXPORT_SYMBOL(vchiq_initialise);
-+
-+/****************************************************************************
-+*
-+* vchiq_shutdown
-+*
-+***************************************************************************/
-+
-+VCHIQ_STATUS_T vchiq_shutdown(VCHIQ_INSTANCE_T instance)
-+{
-+ VCHIQ_STATUS_T status;
-+ VCHIQ_STATE_T *state = instance->state;
-+
-+ vchiq_log_trace(vchiq_core_log_level,
-+ "%s(%p) called", __func__, instance);
-+
-+ if (mutex_lock_interruptible(&state->mutex) != 0)
-+ return VCHIQ_RETRY;
-+
-+ /* Remove all services */
-+ status = vchiq_shutdown_internal(state, instance);
-+
-+ mutex_unlock(&state->mutex);
-+
-+ vchiq_log_trace(vchiq_core_log_level,
-+ "%s(%p): returning %d", __func__, instance, status);
-+
-+ if (status == VCHIQ_SUCCESS) {
-+ struct list_head *pos, *next;
-+ list_for_each_safe(pos, next,
-+ &instance->bulk_waiter_list) {
-+ struct bulk_waiter_node *waiter;
-+ waiter = list_entry(pos,
-+ struct bulk_waiter_node,
-+ list);
-+ list_del(pos);
-+ vchiq_log_info(vchiq_arm_log_level,
-+ "bulk_waiter - cleaned up %x "
-+ "for pid %d",
-+ (unsigned int)waiter, waiter->pid);
-+ kfree(waiter);
-+ }
-+ kfree(instance);
-+ }
-+
-+ return status;
-+}
-+EXPORT_SYMBOL(vchiq_shutdown);
-+
-+/****************************************************************************
-+*
-+* vchiq_is_connected
-+*
-+***************************************************************************/
-+
-+int vchiq_is_connected(VCHIQ_INSTANCE_T instance)
-+{
-+ return instance->connected;
-+}
-+
-+/****************************************************************************
-+*
-+* vchiq_connect
-+*
-+***************************************************************************/
-+
-+VCHIQ_STATUS_T vchiq_connect(VCHIQ_INSTANCE_T instance)
-+{
-+ VCHIQ_STATUS_T status;
-+ VCHIQ_STATE_T *state = instance->state;
-+
-+ vchiq_log_trace(vchiq_core_log_level,
-+ "%s(%p) called", __func__, instance);
-+
-+ if (mutex_lock_interruptible(&state->mutex) != 0) {
-+ vchiq_log_trace(vchiq_core_log_level,
-+ "%s: call to mutex_lock failed", __func__);
-+ status = VCHIQ_RETRY;
-+ goto failed;
-+ }
-+ status = vchiq_connect_internal(state, instance);
-+
-+ if (status == VCHIQ_SUCCESS)
-+ instance->connected = 1;
-+
-+ mutex_unlock(&state->mutex);
-+
-+failed:
-+ vchiq_log_trace(vchiq_core_log_level,
-+ "%s(%p): returning %d", __func__, instance, status);
-+
-+ return status;
-+}
-+EXPORT_SYMBOL(vchiq_connect);
-+
-+/****************************************************************************
-+*
-+* vchiq_add_service
-+*
-+***************************************************************************/
-+
-+VCHIQ_STATUS_T vchiq_add_service(
-+ VCHIQ_INSTANCE_T instance,
-+ const VCHIQ_SERVICE_PARAMS_T *params,
-+ VCHIQ_SERVICE_HANDLE_T *phandle)
-+{
-+ VCHIQ_STATUS_T status;
-+ VCHIQ_STATE_T *state = instance->state;
-+ VCHIQ_SERVICE_T *service = NULL;
-+ int srvstate;
-+
-+ vchiq_log_trace(vchiq_core_log_level,
-+ "%s(%p) called", __func__, instance);
-+
-+ *phandle = VCHIQ_SERVICE_HANDLE_INVALID;
-+
-+ srvstate = vchiq_is_connected(instance)
-+ ? VCHIQ_SRVSTATE_LISTENING
-+ : VCHIQ_SRVSTATE_HIDDEN;
-+
-+ service = vchiq_add_service_internal(
-+ state,
-+ params,
-+ srvstate,
-+ instance,
-+ NULL);
-+
-+ if (service) {
-+ *phandle = service->handle;
-+ status = VCHIQ_SUCCESS;
-+ } else
-+ status = VCHIQ_ERROR;
-+
-+ vchiq_log_trace(vchiq_core_log_level,
-+ "%s(%p): returning %d", __func__, instance, status);
-+
-+ return status;
-+}
-+EXPORT_SYMBOL(vchiq_add_service);
-+
-+/****************************************************************************
-+*
-+* vchiq_open_service
-+*
-+***************************************************************************/
-+
-+VCHIQ_STATUS_T vchiq_open_service(
-+ VCHIQ_INSTANCE_T instance,
-+ const VCHIQ_SERVICE_PARAMS_T *params,
-+ VCHIQ_SERVICE_HANDLE_T *phandle)
-+{
-+ VCHIQ_STATUS_T status = VCHIQ_ERROR;
-+ VCHIQ_STATE_T *state = instance->state;
-+ VCHIQ_SERVICE_T *service = NULL;
-+
-+ vchiq_log_trace(vchiq_core_log_level,
-+ "%s(%p) called", __func__, instance);
-+
-+ *phandle = VCHIQ_SERVICE_HANDLE_INVALID;
-+
-+ if (!vchiq_is_connected(instance))
-+ goto failed;
-+
-+ service = vchiq_add_service_internal(state,
-+ params,
-+ VCHIQ_SRVSTATE_OPENING,
-+ instance,
-+ NULL);
-+
-+ if (service) {
-+ *phandle = service->handle;
-+ status = vchiq_open_service_internal(service, current->pid);
-+ if (status != VCHIQ_SUCCESS) {
-+ vchiq_remove_service(service->handle);
-+ *phandle = VCHIQ_SERVICE_HANDLE_INVALID;
-+ }
-+ }
-+
-+failed:
-+ vchiq_log_trace(vchiq_core_log_level,
-+ "%s(%p): returning %d", __func__, instance, status);
-+
-+ return status;
-+}
-+EXPORT_SYMBOL(vchiq_open_service);
-+
-+VCHIQ_STATUS_T
-+vchiq_queue_bulk_transmit(VCHIQ_SERVICE_HANDLE_T handle,
-+ const void *data, unsigned int size, void *userdata)
-+{
-+ return vchiq_bulk_transfer(handle,
-+ VCHI_MEM_HANDLE_INVALID, (void *)data, size, userdata,
-+ VCHIQ_BULK_MODE_CALLBACK, VCHIQ_BULK_TRANSMIT);
-+}
-+EXPORT_SYMBOL(vchiq_queue_bulk_transmit);
-+
-+VCHIQ_STATUS_T
-+vchiq_queue_bulk_receive(VCHIQ_SERVICE_HANDLE_T handle, void *data,
-+ unsigned int size, void *userdata)
-+{
-+ return vchiq_bulk_transfer(handle,
-+ VCHI_MEM_HANDLE_INVALID, data, size, userdata,
-+ VCHIQ_BULK_MODE_CALLBACK, VCHIQ_BULK_RECEIVE);
-+}
-+EXPORT_SYMBOL(vchiq_queue_bulk_receive);
-+
-+VCHIQ_STATUS_T
-+vchiq_bulk_transmit(VCHIQ_SERVICE_HANDLE_T handle, const void *data,
-+ unsigned int size, void *userdata, VCHIQ_BULK_MODE_T mode)
-+{
-+ VCHIQ_STATUS_T status;
-+
-+ switch (mode) {
-+ case VCHIQ_BULK_MODE_NOCALLBACK:
-+ case VCHIQ_BULK_MODE_CALLBACK:
-+ status = vchiq_bulk_transfer(handle,
-+ VCHI_MEM_HANDLE_INVALID, (void *)data, size, userdata,
-+ mode, VCHIQ_BULK_TRANSMIT);
-+ break;
-+ case VCHIQ_BULK_MODE_BLOCKING:
-+ status = vchiq_blocking_bulk_transfer(handle,
-+ (void *)data, size, VCHIQ_BULK_TRANSMIT);
-+ break;
-+ default:
-+ return VCHIQ_ERROR;
-+ }
-+
-+ return status;
-+}
-+EXPORT_SYMBOL(vchiq_bulk_transmit);
-+
-+VCHIQ_STATUS_T
-+vchiq_bulk_receive(VCHIQ_SERVICE_HANDLE_T handle, void *data,
-+ unsigned int size, void *userdata, VCHIQ_BULK_MODE_T mode)
-+{
-+ VCHIQ_STATUS_T status;
-+
-+ switch (mode) {
-+ case VCHIQ_BULK_MODE_NOCALLBACK:
-+ case VCHIQ_BULK_MODE_CALLBACK:
-+ status = vchiq_bulk_transfer(handle,
-+ VCHI_MEM_HANDLE_INVALID, data, size, userdata,
-+ mode, VCHIQ_BULK_RECEIVE);
-+ break;
-+ case VCHIQ_BULK_MODE_BLOCKING:
-+ status = vchiq_blocking_bulk_transfer(handle,
-+ (void *)data, size, VCHIQ_BULK_RECEIVE);
-+ break;
-+ default:
-+ return VCHIQ_ERROR;
-+ }
-+
-+ return status;
-+}
-+EXPORT_SYMBOL(vchiq_bulk_receive);
-+
-+static VCHIQ_STATUS_T
-+vchiq_blocking_bulk_transfer(VCHIQ_SERVICE_HANDLE_T handle, void *data,
-+ unsigned int size, VCHIQ_BULK_DIR_T dir)
-+{
-+ VCHIQ_INSTANCE_T instance;
-+ VCHIQ_SERVICE_T *service;
-+ VCHIQ_STATUS_T status;
-+ struct bulk_waiter_node *waiter = NULL;
-+ struct list_head *pos;
-+
-+ service = find_service_by_handle(handle);
-+ if (!service)
-+ return VCHIQ_ERROR;
-+
-+ instance = service->instance;
-+
-+ unlock_service(service);
-+
-+ mutex_lock(&instance->bulk_waiter_list_mutex);
-+ list_for_each(pos, &instance->bulk_waiter_list) {
-+ if (list_entry(pos, struct bulk_waiter_node,
-+ list)->pid == current->pid) {
-+ waiter = list_entry(pos,
-+ struct bulk_waiter_node,
-+ list);
-+ list_del(pos);
-+ break;
-+ }
-+ }
-+ mutex_unlock(&instance->bulk_waiter_list_mutex);
-+
-+ if (waiter) {
-+ VCHIQ_BULK_T *bulk = waiter->bulk_waiter.bulk;
-+ if (bulk) {
-+ /* This thread has an outstanding bulk transfer. */
-+ if ((bulk->data != data) ||
-+ (bulk->size != size)) {
-+ /* This is not a retry of the previous one.
-+ ** Cancel the signal when the transfer
-+ ** completes. */
-+ spin_lock(&bulk_waiter_spinlock);
-+ bulk->userdata = NULL;
-+ spin_unlock(&bulk_waiter_spinlock);
-+ }
-+ }
-+ }
-+
-+ if (!waiter) {
-+ waiter = kzalloc(sizeof(struct bulk_waiter_node), GFP_KERNEL);
-+ if (!waiter) {
-+ vchiq_log_error(vchiq_core_log_level,
-+ "%s - out of memory", __func__);
-+ return VCHIQ_ERROR;
-+ }
-+ }
-+
-+ status = vchiq_bulk_transfer(handle, VCHI_MEM_HANDLE_INVALID,
-+ data, size, &waiter->bulk_waiter, VCHIQ_BULK_MODE_BLOCKING,
-+ dir);
-+ if ((status != VCHIQ_RETRY) || fatal_signal_pending(current) ||
-+ !waiter->bulk_waiter.bulk) {
-+ VCHIQ_BULK_T *bulk = waiter->bulk_waiter.bulk;
-+ if (bulk) {
-+ /* Cancel the signal when the transfer
-+ ** completes. */
-+ spin_lock(&bulk_waiter_spinlock);
-+ bulk->userdata = NULL;
-+ spin_unlock(&bulk_waiter_spinlock);
-+ }
-+ kfree(waiter);
-+ } else {
-+ waiter->pid = current->pid;
-+ mutex_lock(&instance->bulk_waiter_list_mutex);
-+ list_add(&waiter->list, &instance->bulk_waiter_list);
-+ mutex_unlock(&instance->bulk_waiter_list_mutex);
-+ vchiq_log_info(vchiq_arm_log_level,
-+ "saved bulk_waiter %x for pid %d",
-+ (unsigned int)waiter, current->pid);
-+ }
-+
-+ return status;
-+}
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_killable.h
-@@ -0,0 +1,69 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#ifndef VCHIQ_KILLABLE_H
-+#define VCHIQ_KILLABLE_H
-+
-+#include <linux/mutex.h>
-+#include <linux/semaphore.h>
-+
-+#define SHUTDOWN_SIGS (sigmask(SIGKILL) | sigmask(SIGINT) | sigmask(SIGQUIT) | sigmask(SIGTRAP) | sigmask(SIGSTOP) | sigmask(SIGCONT))
-+
-+static inline int __must_check down_interruptible_killable(struct semaphore *sem)
-+{
-+ /* Allow interception of killable signals only. We don't want to be interrupted by harmless signals like SIGALRM */
-+ int ret;
-+ sigset_t blocked, oldset;
-+ siginitsetinv(&blocked, SHUTDOWN_SIGS);
-+ sigprocmask(SIG_SETMASK, &blocked, &oldset);
-+ ret = down_interruptible(sem);
-+ sigprocmask(SIG_SETMASK, &oldset, NULL);
-+ return ret;
-+}
-+#define down_interruptible down_interruptible_killable
-+
-+
-+static inline int __must_check mutex_lock_interruptible_killable(struct mutex *lock)
-+{
-+ /* Allow interception of killable signals only. We don't want to be interrupted by harmless signals like SIGALRM */
-+ int ret;
-+ sigset_t blocked, oldset;
-+ siginitsetinv(&blocked, SHUTDOWN_SIGS);
-+ sigprocmask(SIG_SETMASK, &blocked, &oldset);
-+ ret = mutex_lock_interruptible(lock);
-+ sigprocmask(SIG_SETMASK, &oldset, NULL);
-+ return ret;
-+}
-+#define mutex_lock_interruptible mutex_lock_interruptible_killable
-+
-+#endif
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_memdrv.h
-@@ -0,0 +1,71 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#ifndef VCHIQ_MEMDRV_H
-+#define VCHIQ_MEMDRV_H
-+
-+/* ---- Include Files ----------------------------------------------------- */
-+
-+#include <linux/kernel.h>
-+#include "vchiq_if.h"
-+
-+/* ---- Constants and Types ---------------------------------------------- */
-+
-+typedef struct {
-+ void *armSharedMemVirt;
-+ dma_addr_t armSharedMemPhys;
-+ size_t armSharedMemSize;
-+
-+ void *vcSharedMemVirt;
-+ dma_addr_t vcSharedMemPhys;
-+ size_t vcSharedMemSize;
-+} VCHIQ_SHARED_MEM_INFO_T;
-+
-+/* ---- Variable Externs ------------------------------------------------- */
-+
-+/* ---- Function Prototypes ---------------------------------------------- */
-+
-+void vchiq_get_shared_mem_info(VCHIQ_SHARED_MEM_INFO_T *info);
-+
-+VCHIQ_STATUS_T vchiq_memdrv_initialise(void);
-+
-+VCHIQ_STATUS_T vchiq_userdrv_create_instance(
-+ const VCHIQ_PLATFORM_DATA_T * platform_data);
-+
-+VCHIQ_STATUS_T vchiq_userdrv_suspend(
-+ const VCHIQ_PLATFORM_DATA_T * platform_data);
-+
-+VCHIQ_STATUS_T vchiq_userdrv_resume(
-+ const VCHIQ_PLATFORM_DATA_T * platform_data);
-+
-+#endif
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_pagelist.h
-@@ -0,0 +1,58 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#ifndef VCHIQ_PAGELIST_H
-+#define VCHIQ_PAGELIST_H
-+
-+#ifndef PAGE_SIZE
-+#define PAGE_SIZE 4096
-+#endif
-+#define CACHE_LINE_SIZE 32
-+#define PAGELIST_WRITE 0
-+#define PAGELIST_READ 1
-+#define PAGELIST_READ_WITH_FRAGMENTS 2
-+
-+typedef struct pagelist_struct {
-+ unsigned long length;
-+ unsigned short type;
-+ unsigned short offset;
-+ unsigned long addrs[1]; /* N.B. 12 LSBs hold the number of following
-+ pages at consecutive addresses. */
-+} PAGELIST_T;
-+
-+typedef struct fragments_struct {
-+ char headbuf[CACHE_LINE_SIZE];
-+ char tailbuf[CACHE_LINE_SIZE];
-+} FRAGMENTS_T;
-+
-+#endif /* VCHIQ_PAGELIST_H */
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_shim.c
-@@ -0,0 +1,860 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+#include <linux/module.h>
-+#include <linux/types.h>
-+
-+#include "interface/vchi/vchi.h"
-+#include "vchiq.h"
-+#include "vchiq_core.h"
-+
-+#include "vchiq_util.h"
-+
-+#include <stddef.h>
-+
-+#define vchiq_status_to_vchi(status) ((int32_t)status)
-+
-+typedef struct {
-+ VCHIQ_SERVICE_HANDLE_T handle;
-+
-+ VCHIU_QUEUE_T queue;
-+
-+ VCHI_CALLBACK_T callback;
-+ void *callback_param;
-+} SHIM_SERVICE_T;
-+
-+/* ----------------------------------------------------------------------
-+ * return pointer to the mphi message driver function table
-+ * -------------------------------------------------------------------- */
-+const VCHI_MESSAGE_DRIVER_T *
-+vchi_mphi_message_driver_func_table(void)
-+{
-+ return NULL;
-+}
-+
-+/* ----------------------------------------------------------------------
-+ * return a pointer to the 'single' connection driver fops
-+ * -------------------------------------------------------------------- */
-+const VCHI_CONNECTION_API_T *
-+single_get_func_table(void)
-+{
-+ return NULL;
-+}
-+
-+VCHI_CONNECTION_T *vchi_create_connection(
-+ const VCHI_CONNECTION_API_T *function_table,
-+ const VCHI_MESSAGE_DRIVER_T *low_level)
-+{
-+ (void)function_table;
-+ (void)low_level;
-+ return NULL;
-+}
-+
-+/***********************************************************
-+ * Name: vchi_msg_peek
-+ *
-+ * Arguments: const VCHI_SERVICE_HANDLE_T handle,
-+ * void **data,
-+ * uint32_t *msg_size,
-+
-+
-+ * VCHI_FLAGS_T flags
-+ *
-+ * Description: Routine to return a pointer to the current message (to allow in
-+ * place processing). The message can be removed using
-+ * vchi_msg_remove when you're finished
-+ *
-+ * Returns: int32_t - success == 0
-+ *
-+ ***********************************************************/
-+int32_t vchi_msg_peek(VCHI_SERVICE_HANDLE_T handle,
-+ void **data,
-+ uint32_t *msg_size,
-+ VCHI_FLAGS_T flags)
-+{
-+ SHIM_SERVICE_T *service = (SHIM_SERVICE_T *)handle;
-+ VCHIQ_HEADER_T *header;
-+
-+ WARN_ON((flags != VCHI_FLAGS_NONE) &&
-+ (flags != VCHI_FLAGS_BLOCK_UNTIL_OP_COMPLETE));
-+
-+ if (flags == VCHI_FLAGS_NONE)
-+ if (vchiu_queue_is_empty(&service->queue))
-+ return -1;
-+
-+ header = vchiu_queue_peek(&service->queue);
-+
-+ *data = header->data;
-+ *msg_size = header->size;
-+
-+ return 0;
-+}
-+EXPORT_SYMBOL(vchi_msg_peek);
-+
-+/***********************************************************
-+ * Name: vchi_msg_remove
-+ *
-+ * Arguments: const VCHI_SERVICE_HANDLE_T handle,
-+ *
-+ * Description: Routine to remove a message (after it has been read with
-+ * vchi_msg_peek)
-+ *
-+ * Returns: int32_t - success == 0
-+ *
-+ ***********************************************************/
-+int32_t vchi_msg_remove(VCHI_SERVICE_HANDLE_T handle)
-+{
-+ SHIM_SERVICE_T *service = (SHIM_SERVICE_T *)handle;
-+ VCHIQ_HEADER_T *header;
-+
-+ header = vchiu_queue_pop(&service->queue);
-+
-+ vchiq_release_message(service->handle, header);
-+
-+ return 0;
-+}
-+EXPORT_SYMBOL(vchi_msg_remove);
-+
-+/***********************************************************
-+ * Name: vchi_msg_queue
-+ *
-+ * Arguments: VCHI_SERVICE_HANDLE_T handle,
-+ * const void *data,
-+ * uint32_t data_size,
-+ * VCHI_FLAGS_T flags,
-+ * void *msg_handle,
-+ *
-+ * Description: Thin wrapper to queue a message onto a connection
-+ *
-+ * Returns: int32_t - success == 0
-+ *
-+ ***********************************************************/
-+int32_t vchi_msg_queue(VCHI_SERVICE_HANDLE_T handle,
-+ const void *data,
-+ uint32_t data_size,
-+ VCHI_FLAGS_T flags,
-+ void *msg_handle)
-+{
-+ SHIM_SERVICE_T *service = (SHIM_SERVICE_T *)handle;
-+ VCHIQ_ELEMENT_T element = {data, data_size};
-+ VCHIQ_STATUS_T status;
-+
-+ (void)msg_handle;
-+
-+ WARN_ON(flags != VCHI_FLAGS_BLOCK_UNTIL_QUEUED);
-+
-+ status = vchiq_queue_message(service->handle, &element, 1);
-+
-+ /* vchiq_queue_message() may return VCHIQ_RETRY, so we need to
-+ ** implement a retry mechanism since this function is supposed
-+ ** to block until queued
-+ */
-+ while (status == VCHIQ_RETRY) {
-+ msleep(1);
-+ status = vchiq_queue_message(service->handle, &element, 1);
-+ }
-+
-+ return vchiq_status_to_vchi(status);
-+}
-+EXPORT_SYMBOL(vchi_msg_queue);
-+
-+/***********************************************************
-+ * Name: vchi_bulk_queue_receive
-+ *
-+ * Arguments: VCHI_BULK_HANDLE_T handle,
-+ * void *data_dst,
-+ * const uint32_t data_size,
-+ * VCHI_FLAGS_T flags
-+ * void *bulk_handle
-+ *
-+ * Description: Routine to setup a rcv buffer
-+ *
-+ * Returns: int32_t - success == 0
-+ *
-+ ***********************************************************/
-+int32_t vchi_bulk_queue_receive(VCHI_SERVICE_HANDLE_T handle,
-+ void *data_dst,
-+ uint32_t data_size,
-+ VCHI_FLAGS_T flags,
-+ void *bulk_handle)
-+{
-+ SHIM_SERVICE_T *service = (SHIM_SERVICE_T *)handle;
-+ VCHIQ_BULK_MODE_T mode;
-+ VCHIQ_STATUS_T status;
-+
-+ switch ((int)flags) {
-+ case VCHI_FLAGS_CALLBACK_WHEN_OP_COMPLETE
-+ | VCHI_FLAGS_BLOCK_UNTIL_QUEUED:
-+ WARN_ON(!service->callback);
-+ mode = VCHIQ_BULK_MODE_CALLBACK;
-+ break;
-+ case VCHI_FLAGS_BLOCK_UNTIL_OP_COMPLETE:
-+ mode = VCHIQ_BULK_MODE_BLOCKING;
-+ break;
-+ case VCHI_FLAGS_BLOCK_UNTIL_QUEUED:
-+ case VCHI_FLAGS_NONE:
-+ mode = VCHIQ_BULK_MODE_NOCALLBACK;
-+ break;
-+ default:
-+ WARN(1, "unsupported message\n");
-+ return vchiq_status_to_vchi(VCHIQ_ERROR);
-+ }
-+
-+ status = vchiq_bulk_receive(service->handle, data_dst, data_size,
-+ bulk_handle, mode);
-+
-+ /* vchiq_bulk_receive() may return VCHIQ_RETRY, so we need to
-+ ** implement a retry mechanism since this function is supposed
-+ ** to block until queued
-+ */
-+ while (status == VCHIQ_RETRY) {
-+ msleep(1);
-+ status = vchiq_bulk_receive(service->handle, data_dst,
-+ data_size, bulk_handle, mode);
-+ }
-+
-+ return vchiq_status_to_vchi(status);
-+}
-+EXPORT_SYMBOL(vchi_bulk_queue_receive);
-+
-+/***********************************************************
-+ * Name: vchi_bulk_queue_transmit
-+ *
-+ * Arguments: VCHI_BULK_HANDLE_T handle,
-+ * const void *data_src,
-+ * uint32_t data_size,
-+ * VCHI_FLAGS_T flags,
-+ * void *bulk_handle
-+ *
-+ * Description: Routine to transmit some data
-+ *
-+ * Returns: int32_t - success == 0
-+ *
-+ ***********************************************************/
-+int32_t vchi_bulk_queue_transmit(VCHI_SERVICE_HANDLE_T handle,
-+ const void *data_src,
-+ uint32_t data_size,
-+ VCHI_FLAGS_T flags,
-+ void *bulk_handle)
-+{
-+ SHIM_SERVICE_T *service = (SHIM_SERVICE_T *)handle;
-+ VCHIQ_BULK_MODE_T mode;
-+ VCHIQ_STATUS_T status;
-+
-+ switch ((int)flags) {
-+ case VCHI_FLAGS_CALLBACK_WHEN_OP_COMPLETE
-+ | VCHI_FLAGS_BLOCK_UNTIL_QUEUED:
-+ WARN_ON(!service->callback);
-+ mode = VCHIQ_BULK_MODE_CALLBACK;
-+ break;
-+ case VCHI_FLAGS_BLOCK_UNTIL_DATA_READ:
-+ case VCHI_FLAGS_BLOCK_UNTIL_OP_COMPLETE:
-+ mode = VCHIQ_BULK_MODE_BLOCKING;
-+ break;
-+ case VCHI_FLAGS_BLOCK_UNTIL_QUEUED:
-+ case VCHI_FLAGS_NONE:
-+ mode = VCHIQ_BULK_MODE_NOCALLBACK;
-+ break;
-+ default:
-+ WARN(1, "unsupported message\n");
-+ return vchiq_status_to_vchi(VCHIQ_ERROR);
-+ }
-+
-+ status = vchiq_bulk_transmit(service->handle, data_src, data_size,
-+ bulk_handle, mode);
-+
-+ /* vchiq_bulk_transmit() may return VCHIQ_RETRY, so we need to
-+ ** implement a retry mechanism since this function is supposed
-+ ** to block until queued
-+ */
-+ while (status == VCHIQ_RETRY) {
-+ msleep(1);
-+ status = vchiq_bulk_transmit(service->handle, data_src,
-+ data_size, bulk_handle, mode);
-+ }
-+
-+ return vchiq_status_to_vchi(status);
-+}
-+EXPORT_SYMBOL(vchi_bulk_queue_transmit);
-+
-+/***********************************************************
-+ * Name: vchi_msg_dequeue
-+ *
-+ * Arguments: VCHI_SERVICE_HANDLE_T handle,
-+ * void *data,
-+ * uint32_t max_data_size_to_read,
-+ * uint32_t *actual_msg_size
-+ * VCHI_FLAGS_T flags
-+ *
-+ * Description: Routine to dequeue a message into the supplied buffer
-+ *
-+ * Returns: int32_t - success == 0
-+ *
-+ ***********************************************************/
-+int32_t vchi_msg_dequeue(VCHI_SERVICE_HANDLE_T handle,
-+ void *data,
-+ uint32_t max_data_size_to_read,
-+ uint32_t *actual_msg_size,
-+ VCHI_FLAGS_T flags)
-+{
-+ SHIM_SERVICE_T *service = (SHIM_SERVICE_T *)handle;
-+ VCHIQ_HEADER_T *header;
-+
-+ WARN_ON((flags != VCHI_FLAGS_NONE) &&
-+ (flags != VCHI_FLAGS_BLOCK_UNTIL_OP_COMPLETE));
-+
-+ if (flags == VCHI_FLAGS_NONE)
-+ if (vchiu_queue_is_empty(&service->queue))
-+ return -1;
-+
-+ header = vchiu_queue_pop(&service->queue);
-+
-+ memcpy(data, header->data, header->size < max_data_size_to_read ?
-+ header->size : max_data_size_to_read);
-+
-+ *actual_msg_size = header->size;
-+
-+ vchiq_release_message(service->handle, header);
-+
-+ return 0;
-+}
-+EXPORT_SYMBOL(vchi_msg_dequeue);
-+
-+/***********************************************************
-+ * Name: vchi_msg_queuev
-+ *
-+ * Arguments: VCHI_SERVICE_HANDLE_T handle,
-+ * VCHI_MSG_VECTOR_T *vector,
-+ * uint32_t count,
-+ * VCHI_FLAGS_T flags,
-+ * void *msg_handle
-+ *
-+ * Description: Thin wrapper to queue a message onto a connection
-+ *
-+ * Returns: int32_t - success == 0
-+ *
-+ ***********************************************************/
-+
-+vchiq_static_assert(sizeof(VCHI_MSG_VECTOR_T) == sizeof(VCHIQ_ELEMENT_T));
-+vchiq_static_assert(offsetof(VCHI_MSG_VECTOR_T, vec_base) ==
-+ offsetof(VCHIQ_ELEMENT_T, data));
-+vchiq_static_assert(offsetof(VCHI_MSG_VECTOR_T, vec_len) ==
-+ offsetof(VCHIQ_ELEMENT_T, size));
-+
-+int32_t vchi_msg_queuev(VCHI_SERVICE_HANDLE_T handle,
-+ VCHI_MSG_VECTOR_T *vector,
-+ uint32_t count,
-+ VCHI_FLAGS_T flags,
-+ void *msg_handle)
-+{
-+ SHIM_SERVICE_T *service = (SHIM_SERVICE_T *)handle;
-+
-+ (void)msg_handle;
-+
-+ WARN_ON(flags != VCHI_FLAGS_BLOCK_UNTIL_QUEUED);
-+
-+ return vchiq_status_to_vchi(vchiq_queue_message(service->handle,
-+ (const VCHIQ_ELEMENT_T *)vector, count));
-+}
-+EXPORT_SYMBOL(vchi_msg_queuev);
-+
-+/***********************************************************
-+ * Name: vchi_held_msg_release
-+ *
-+ * Arguments: VCHI_HELD_MSG_T *message
-+ *
-+ * Description: Routine to release a held message (after it has been read with
-+ * vchi_msg_hold)
-+ *
-+ * Returns: int32_t - success == 0
-+ *
-+ ***********************************************************/
-+int32_t vchi_held_msg_release(VCHI_HELD_MSG_T *message)
-+{
-+ vchiq_release_message((VCHIQ_SERVICE_HANDLE_T)message->service,
-+ (VCHIQ_HEADER_T *)message->message);
-+
-+ return 0;
-+}
-+EXPORT_SYMBOL(vchi_held_msg_release);
-+
-+/***********************************************************
-+ * Name: vchi_msg_hold
-+ *
-+ * Arguments: VCHI_SERVICE_HANDLE_T handle,
-+ * void **data,
-+ * uint32_t *msg_size,
-+ * VCHI_FLAGS_T flags,
-+ * VCHI_HELD_MSG_T *message_handle
-+ *
-+ * Description: Routine to return a pointer to the current message (to allow
-+ * in place processing). The message is dequeued - don't forget
-+ * to release the message using vchi_held_msg_release when you're
-+ * finished.
-+ *
-+ * Returns: int32_t - success == 0
-+ *
-+ ***********************************************************/
-+int32_t vchi_msg_hold(VCHI_SERVICE_HANDLE_T handle,
-+ void **data,
-+ uint32_t *msg_size,
-+ VCHI_FLAGS_T flags,
-+ VCHI_HELD_MSG_T *message_handle)
-+{
-+ SHIM_SERVICE_T *service = (SHIM_SERVICE_T *)handle;
-+ VCHIQ_HEADER_T *header;
-+
-+ WARN_ON((flags != VCHI_FLAGS_NONE) &&
-+ (flags != VCHI_FLAGS_BLOCK_UNTIL_OP_COMPLETE));
-+
-+ if (flags == VCHI_FLAGS_NONE)
-+ if (vchiu_queue_is_empty(&service->queue))
-+ return -1;
-+
-+ header = vchiu_queue_pop(&service->queue);
-+
-+ *data = header->data;
-+ *msg_size = header->size;
-+
-+ message_handle->service =
-+ (struct opaque_vchi_service_t *)service->handle;
-+ message_handle->message = header;
-+
-+ return 0;
-+}
-+EXPORT_SYMBOL(vchi_msg_hold);
-+
-+/***********************************************************
-+ * Name: vchi_initialise
-+ *
-+ * Arguments: VCHI_INSTANCE_T *instance_handle
-+ *
-+ * Description: Initialises the hardware but does not transmit anything
-+ * When run as a Host App this will be called twice hence the need
-+ * to malloc the state information
-+ *
-+ * Returns: 0 if successful, failure otherwise
-+ *
-+ ***********************************************************/
-+
-+int32_t vchi_initialise(VCHI_INSTANCE_T *instance_handle)
-+{
-+ VCHIQ_INSTANCE_T instance;
-+ VCHIQ_STATUS_T status;
-+
-+ status = vchiq_initialise(&instance);
-+
-+ *instance_handle = (VCHI_INSTANCE_T)instance;
-+
-+ return vchiq_status_to_vchi(status);
-+}
-+EXPORT_SYMBOL(vchi_initialise);
-+
-+/***********************************************************
-+ * Name: vchi_connect
-+ *
-+ * Arguments: VCHI_CONNECTION_T **connections
-+ * const uint32_t num_connections
-+ * VCHI_INSTANCE_T instance_handle)
-+ *
-+ * Description: Starts the command service on each connection,
-+ * causing INIT messages to be pinged back and forth
-+ *
-+ * Returns: 0 if successful, failure otherwise
-+ *
-+ ***********************************************************/
-+int32_t vchi_connect(VCHI_CONNECTION_T **connections,
-+ const uint32_t num_connections,
-+ VCHI_INSTANCE_T instance_handle)
-+{
-+ VCHIQ_INSTANCE_T instance = (VCHIQ_INSTANCE_T)instance_handle;
-+
-+ (void)connections;
-+ (void)num_connections;
-+
-+ return vchiq_connect(instance);
-+}
-+EXPORT_SYMBOL(vchi_connect);
-+
-+
-+/***********************************************************
-+ * Name: vchi_disconnect
-+ *
-+ * Arguments: VCHI_INSTANCE_T instance_handle
-+ *
-+ * Description: Stops the command service on each connection,
-+ * causing DE-INIT messages to be pinged back and forth
-+ *
-+ * Returns: 0 if successful, failure otherwise
-+ *
-+ ***********************************************************/
-+int32_t vchi_disconnect(VCHI_INSTANCE_T instance_handle)
-+{
-+ VCHIQ_INSTANCE_T instance = (VCHIQ_INSTANCE_T)instance_handle;
-+ return vchiq_status_to_vchi(vchiq_shutdown(instance));
-+}
-+EXPORT_SYMBOL(vchi_disconnect);
-+
-+
-+/***********************************************************
-+ * Name: vchi_service_open
-+ * Name: vchi_service_create
-+ *
-+ * Arguments: VCHI_INSTANCE_T *instance_handle
-+ * SERVICE_CREATION_T *setup,
-+ * VCHI_SERVICE_HANDLE_T *handle
-+ *
-+ * Description: Routine to open a service
-+ *
-+ * Returns: int32_t - success == 0
-+ *
-+ ***********************************************************/
-+
-+static VCHIQ_STATUS_T shim_callback(VCHIQ_REASON_T reason,
-+ VCHIQ_HEADER_T *header, VCHIQ_SERVICE_HANDLE_T handle, void *bulk_user)
-+{
-+ SHIM_SERVICE_T *service =
-+ (SHIM_SERVICE_T *)VCHIQ_GET_SERVICE_USERDATA(handle);
-+
-+ if (!service->callback)
-+ goto release;
-+
-+ switch (reason) {
-+ case VCHIQ_MESSAGE_AVAILABLE:
-+ vchiu_queue_push(&service->queue, header);
-+
-+ service->callback(service->callback_param,
-+ VCHI_CALLBACK_MSG_AVAILABLE, NULL);
-+
-+ goto done;
-+ break;
-+
-+ case VCHIQ_BULK_TRANSMIT_DONE:
-+ service->callback(service->callback_param,
-+ VCHI_CALLBACK_BULK_SENT, bulk_user);
-+ break;
-+
-+ case VCHIQ_BULK_RECEIVE_DONE:
-+ service->callback(service->callback_param,
-+ VCHI_CALLBACK_BULK_RECEIVED, bulk_user);
-+ break;
-+
-+ case VCHIQ_SERVICE_CLOSED:
-+ service->callback(service->callback_param,
-+ VCHI_CALLBACK_SERVICE_CLOSED, NULL);
-+ break;
-+
-+ case VCHIQ_SERVICE_OPENED:
-+ /* No equivalent VCHI reason */
-+ break;
-+
-+ case VCHIQ_BULK_TRANSMIT_ABORTED:
-+ service->callback(service->callback_param,
-+ VCHI_CALLBACK_BULK_TRANSMIT_ABORTED,
-+ bulk_user);
-+ break;
-+
-+ case VCHIQ_BULK_RECEIVE_ABORTED:
-+ service->callback(service->callback_param,
-+ VCHI_CALLBACK_BULK_RECEIVE_ABORTED,
-+ bulk_user);
-+ break;
-+
-+ default:
-+ WARN(1, "not supported\n");
-+ break;
-+ }
-+
-+release:
-+ vchiq_release_message(service->handle, header);
-+done:
-+ return VCHIQ_SUCCESS;
-+}
-+
-+static SHIM_SERVICE_T *service_alloc(VCHIQ_INSTANCE_T instance,
-+ SERVICE_CREATION_T *setup)
-+{
-+ SHIM_SERVICE_T *service = kzalloc(sizeof(SHIM_SERVICE_T), GFP_KERNEL);
-+
-+ (void)instance;
-+
-+ if (service) {
-+ if (vchiu_queue_init(&service->queue, 64)) {
-+ service->callback = setup->callback;
-+ service->callback_param = setup->callback_param;
-+ } else {
-+ kfree(service);
-+ service = NULL;
-+ }
-+ }
-+
-+ return service;
-+}
-+
-+static void service_free(SHIM_SERVICE_T *service)
-+{
-+ if (service) {
-+ vchiu_queue_delete(&service->queue);
-+ kfree(service);
-+ }
-+}
-+
-+int32_t vchi_service_open(VCHI_INSTANCE_T instance_handle,
-+ SERVICE_CREATION_T *setup,
-+ VCHI_SERVICE_HANDLE_T *handle)
-+{
-+ VCHIQ_INSTANCE_T instance = (VCHIQ_INSTANCE_T)instance_handle;
-+ SHIM_SERVICE_T *service = service_alloc(instance, setup);
-+
-+ *handle = (VCHI_SERVICE_HANDLE_T)service;
-+
-+ if (service) {
-+ VCHIQ_SERVICE_PARAMS_T params;
-+ VCHIQ_STATUS_T status;
-+
-+ memset(¶ms, 0, sizeof(params));
-+ params.fourcc = setup->service_id;
-+ params.callback = shim_callback;
-+ params.userdata = service;
-+ params.version = setup->version.version;
-+ params.version_min = setup->version.version_min;
-+
-+ status = vchiq_open_service(instance, ¶ms,
-+ &service->handle);
-+ if (status != VCHIQ_SUCCESS) {
-+ service_free(service);
-+ service = NULL;
-+ *handle = NULL;
-+ }
-+ }
-+
-+ return (service != NULL) ? 0 : -1;
-+}
-+EXPORT_SYMBOL(vchi_service_open);
-+
-+int32_t vchi_service_create(VCHI_INSTANCE_T instance_handle,
-+ SERVICE_CREATION_T *setup,
-+ VCHI_SERVICE_HANDLE_T *handle)
-+{
-+ VCHIQ_INSTANCE_T instance = (VCHIQ_INSTANCE_T)instance_handle;
-+ SHIM_SERVICE_T *service = service_alloc(instance, setup);
-+
-+ *handle = (VCHI_SERVICE_HANDLE_T)service;
-+
-+ if (service) {
-+ VCHIQ_SERVICE_PARAMS_T params;
-+ VCHIQ_STATUS_T status;
-+
-+ memset(¶ms, 0, sizeof(params));
-+ params.fourcc = setup->service_id;
-+ params.callback = shim_callback;
-+ params.userdata = service;
-+ params.version = setup->version.version;
-+ params.version_min = setup->version.version_min;
-+ status = vchiq_add_service(instance, ¶ms, &service->handle);
-+
-+ if (status != VCHIQ_SUCCESS) {
-+ service_free(service);
-+ service = NULL;
-+ *handle = NULL;
-+ }
-+ }
-+
-+ return (service != NULL) ? 0 : -1;
-+}
-+EXPORT_SYMBOL(vchi_service_create);
-+
-+int32_t vchi_service_close(const VCHI_SERVICE_HANDLE_T handle)
-+{
-+ int32_t ret = -1;
-+ SHIM_SERVICE_T *service = (SHIM_SERVICE_T *)handle;
-+ if (service) {
-+ VCHIQ_STATUS_T status = vchiq_close_service(service->handle);
-+ if (status == VCHIQ_SUCCESS) {
-+ service_free(service);
-+ service = NULL;
-+ }
-+
-+ ret = vchiq_status_to_vchi(status);
-+ }
-+ return ret;
-+}
-+EXPORT_SYMBOL(vchi_service_close);
-+
-+int32_t vchi_service_destroy(const VCHI_SERVICE_HANDLE_T handle)
-+{
-+ int32_t ret = -1;
-+ SHIM_SERVICE_T *service = (SHIM_SERVICE_T *)handle;
-+ if (service) {
-+ VCHIQ_STATUS_T status = vchiq_remove_service(service->handle);
-+ if (status == VCHIQ_SUCCESS) {
-+ service_free(service);
-+ service = NULL;
-+ }
-+
-+ ret = vchiq_status_to_vchi(status);
-+ }
-+ return ret;
-+}
-+EXPORT_SYMBOL(vchi_service_destroy);
-+
-+int32_t vchi_service_set_option(const VCHI_SERVICE_HANDLE_T handle,
-+ VCHI_SERVICE_OPTION_T option,
-+ int value)
-+{
-+ int32_t ret = -1;
-+ SHIM_SERVICE_T *service = (SHIM_SERVICE_T *)handle;
-+ VCHIQ_SERVICE_OPTION_T vchiq_option;
-+ switch (option) {
-+ case VCHI_SERVICE_OPTION_TRACE:
-+ vchiq_option = VCHIQ_SERVICE_OPTION_TRACE;
-+ break;
-+ case VCHI_SERVICE_OPTION_SYNCHRONOUS:
-+ vchiq_option = VCHIQ_SERVICE_OPTION_SYNCHRONOUS;
-+ break;
-+ default:
-+ service = NULL;
-+ break;
-+ }
-+ if (service) {
-+ VCHIQ_STATUS_T status =
-+ vchiq_set_service_option(service->handle,
-+ vchiq_option,
-+ value);
-+
-+ ret = vchiq_status_to_vchi(status);
-+ }
-+ return ret;
-+}
-+EXPORT_SYMBOL(vchi_service_set_option);
-+
-+int32_t vchi_get_peer_version( const VCHI_SERVICE_HANDLE_T handle, short *peer_version )
-+{
-+ int32_t ret = -1;
-+ SHIM_SERVICE_T *service = (SHIM_SERVICE_T *)handle;
-+ if(service)
-+ {
-+ VCHIQ_STATUS_T status = vchiq_get_peer_version(service->handle, peer_version);
-+ ret = vchiq_status_to_vchi( status );
-+ }
-+ return ret;
-+}
-+EXPORT_SYMBOL(vchi_get_peer_version);
-+
-+/* ----------------------------------------------------------------------
-+ * read a uint32_t from buffer.
-+ * network format is defined to be little endian
-+ * -------------------------------------------------------------------- */
-+uint32_t
-+vchi_readbuf_uint32(const void *_ptr)
-+{
-+ const unsigned char *ptr = _ptr;
-+ return ptr[0] | (ptr[1] << 8) | (ptr[2] << 16) | (ptr[3] << 24);
-+}
-+
-+/* ----------------------------------------------------------------------
-+ * write a uint32_t to buffer.
-+ * network format is defined to be little endian
-+ * -------------------------------------------------------------------- */
-+void
-+vchi_writebuf_uint32(void *_ptr, uint32_t value)
-+{
-+ unsigned char *ptr = _ptr;
-+ ptr[0] = (unsigned char)((value >> 0) & 0xFF);
-+ ptr[1] = (unsigned char)((value >> 8) & 0xFF);
-+ ptr[2] = (unsigned char)((value >> 16) & 0xFF);
-+ ptr[3] = (unsigned char)((value >> 24) & 0xFF);
-+}
-+
-+/* ----------------------------------------------------------------------
-+ * read a uint16_t from buffer.
-+ * network format is defined to be little endian
-+ * -------------------------------------------------------------------- */
-+uint16_t
-+vchi_readbuf_uint16(const void *_ptr)
-+{
-+ const unsigned char *ptr = _ptr;
-+ return ptr[0] | (ptr[1] << 8);
-+}
-+
-+/* ----------------------------------------------------------------------
-+ * write a uint16_t into the buffer.
-+ * network format is defined to be little endian
-+ * -------------------------------------------------------------------- */
-+void
-+vchi_writebuf_uint16(void *_ptr, uint16_t value)
-+{
-+ unsigned char *ptr = _ptr;
-+ ptr[0] = (value >> 0) & 0xFF;
-+ ptr[1] = (value >> 8) & 0xFF;
-+}
-+
-+/***********************************************************
-+ * Name: vchi_service_use
-+ *
-+ * Arguments: const VCHI_SERVICE_HANDLE_T handle
-+ *
-+ * Description: Routine to increment refcount on a service
-+ *
-+ * Returns: void
-+ *
-+ ***********************************************************/
-+int32_t vchi_service_use(const VCHI_SERVICE_HANDLE_T handle)
-+{
-+ int32_t ret = -1;
-+ SHIM_SERVICE_T *service = (SHIM_SERVICE_T *)handle;
-+ if (service)
-+ ret = vchiq_status_to_vchi(vchiq_use_service(service->handle));
-+ return ret;
-+}
-+EXPORT_SYMBOL(vchi_service_use);
-+
-+/***********************************************************
-+ * Name: vchi_service_release
-+ *
-+ * Arguments: const VCHI_SERVICE_HANDLE_T handle
-+ *
-+ * Description: Routine to decrement refcount on a service
-+ *
-+ * Returns: void
-+ *
-+ ***********************************************************/
-+int32_t vchi_service_release(const VCHI_SERVICE_HANDLE_T handle)
-+{
-+ int32_t ret = -1;
-+ SHIM_SERVICE_T *service = (SHIM_SERVICE_T *)handle;
-+ if (service)
-+ ret = vchiq_status_to_vchi(
-+ vchiq_release_service(service->handle));
-+ return ret;
-+}
-+EXPORT_SYMBOL(vchi_service_release);
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_util.c
-@@ -0,0 +1,156 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#include "vchiq_util.h"
-+#include "vchiq_killable.h"
-+
-+static inline int is_pow2(int i)
-+{
-+ return i && !(i & (i - 1));
-+}
-+
-+int vchiu_queue_init(VCHIU_QUEUE_T *queue, int size)
-+{
-+ WARN_ON(!is_pow2(size));
-+
-+ queue->size = size;
-+ queue->read = 0;
-+ queue->write = 0;
-+ queue->initialized = 1;
-+
-+ sema_init(&queue->pop, 0);
-+ sema_init(&queue->push, 0);
-+
-+ queue->storage = kzalloc(size * sizeof(VCHIQ_HEADER_T *), GFP_KERNEL);
-+ if (queue->storage == NULL) {
-+ vchiu_queue_delete(queue);
-+ return 0;
-+ }
-+ return 1;
-+}
-+
-+void vchiu_queue_delete(VCHIU_QUEUE_T *queue)
-+{
-+ if (queue->storage != NULL)
-+ kfree(queue->storage);
-+}
-+
-+int vchiu_queue_is_empty(VCHIU_QUEUE_T *queue)
-+{
-+ return queue->read == queue->write;
-+}
-+
-+int vchiu_queue_is_full(VCHIU_QUEUE_T *queue)
-+{
-+ return queue->write == queue->read + queue->size;
-+}
-+
-+void vchiu_queue_push(VCHIU_QUEUE_T *queue, VCHIQ_HEADER_T *header)
-+{
-+ if (!queue->initialized)
-+ return;
-+
-+ while (queue->write == queue->read + queue->size) {
-+ if (down_interruptible(&queue->pop) != 0) {
-+ flush_signals(current);
-+ }
-+ }
-+
-+ /*
-+ * Write to queue->storage must be visible after read from
-+ * queue->read
-+ */
-+ smp_mb();
-+
-+ queue->storage[queue->write & (queue->size - 1)] = header;
-+
-+ /*
-+ * Write to queue->storage must be visible before write to
-+ * queue->write
-+ */
-+ smp_wmb();
-+
-+ queue->write++;
-+
-+ up(&queue->push);
-+}
-+
-+VCHIQ_HEADER_T *vchiu_queue_peek(VCHIU_QUEUE_T *queue)
-+{
-+ while (queue->write == queue->read) {
-+ if (down_interruptible(&queue->push) != 0) {
-+ flush_signals(current);
-+ }
-+ }
-+
-+ up(&queue->push); // We haven't removed anything from the queue.
-+
-+ /*
-+ * Read from queue->storage must be visible after read from
-+ * queue->write
-+ */
-+ smp_rmb();
-+
-+ return queue->storage[queue->read & (queue->size - 1)];
-+}
-+
-+VCHIQ_HEADER_T *vchiu_queue_pop(VCHIU_QUEUE_T *queue)
-+{
-+ VCHIQ_HEADER_T *header;
-+
-+ while (queue->write == queue->read) {
-+ if (down_interruptible(&queue->push) != 0) {
-+ flush_signals(current);
-+ }
-+ }
-+
-+ /*
-+ * Read from queue->storage must be visible after read from
-+ * queue->write
-+ */
-+ smp_rmb();
-+
-+ header = queue->storage[queue->read & (queue->size - 1)];
-+
-+ /*
-+ * Read from queue->storage must be visible before write to
-+ * queue->read
-+ */
-+ smp_mb();
-+
-+ queue->read++;
-+
-+ up(&queue->pop);
-+
-+ return header;
-+}
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_util.h
-@@ -0,0 +1,82 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#ifndef VCHIQ_UTIL_H
-+#define VCHIQ_UTIL_H
-+
-+#include <linux/types.h>
-+#include <linux/semaphore.h>
-+#include <linux/mutex.h>
-+#include <linux/bitops.h>
-+#include <linux/kthread.h>
-+#include <linux/wait.h>
-+#include <linux/vmalloc.h>
-+#include <linux/jiffies.h>
-+#include <linux/delay.h>
-+#include <linux/string.h>
-+#include <linux/types.h>
-+#include <linux/interrupt.h>
-+#include <linux/random.h>
-+#include <linux/sched.h>
-+#include <linux/ctype.h>
-+#include <linux/uaccess.h>
-+#include <linux/time.h> /* for time_t */
-+#include <linux/slab.h>
-+#include <linux/vmalloc.h>
-+
-+#include "vchiq_if.h"
-+
-+typedef struct {
-+ int size;
-+ int read;
-+ int write;
-+ int initialized;
-+
-+ struct semaphore pop;
-+ struct semaphore push;
-+
-+ VCHIQ_HEADER_T **storage;
-+} VCHIU_QUEUE_T;
-+
-+extern int vchiu_queue_init(VCHIU_QUEUE_T *queue, int size);
-+extern void vchiu_queue_delete(VCHIU_QUEUE_T *queue);
-+
-+extern int vchiu_queue_is_empty(VCHIU_QUEUE_T *queue);
-+extern int vchiu_queue_is_full(VCHIU_QUEUE_T *queue);
-+
-+extern void vchiu_queue_push(VCHIU_QUEUE_T *queue, VCHIQ_HEADER_T *header);
-+
-+extern VCHIQ_HEADER_T *vchiu_queue_peek(VCHIU_QUEUE_T *queue);
-+extern VCHIQ_HEADER_T *vchiu_queue_pop(VCHIU_QUEUE_T *queue);
-+
-+#endif
---- /dev/null
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_version.c
-@@ -0,0 +1,59 @@
-+/**
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+#include "vchiq_build_info.h"
-+#include <linux/broadcom/vc_debug_sym.h>
-+
-+VC_DEBUG_DECLARE_STRING_VAR( vchiq_build_hostname, "dc4-arm-01" );
-+VC_DEBUG_DECLARE_STRING_VAR( vchiq_build_version, "9245b4c35b99b3870e1f7dc598c5692b3c66a6f0 (tainted)" );
-+VC_DEBUG_DECLARE_STRING_VAR( vchiq_build_time, __TIME__ );
-+VC_DEBUG_DECLARE_STRING_VAR( vchiq_build_date, __DATE__ );
-+
-+const char *vchiq_get_build_hostname( void )
-+{
-+ return vchiq_build_hostname;
-+}
-+
-+const char *vchiq_get_build_version( void )
-+{
-+ return vchiq_build_version;
-+}
-+
-+const char *vchiq_get_build_date( void )
-+{
-+ return vchiq_build_date;
-+}
-+
-+const char *vchiq_get_build_time( void )
-+{
-+ return vchiq_build_time;
-+}
diff --git a/target/linux/brcm2708/patches-4.4/0037-vc_mem-Add-vc_mem-driver.patch b/target/linux/brcm2708/patches-4.4/0037-vc_mem-Add-vc_mem-driver.patch
deleted file mode 100644
index 1036433..0000000
--- a/target/linux/brcm2708/patches-4.4/0037-vc_mem-Add-vc_mem-driver.patch
+++ /dev/null
@@ -1,991 +0,0 @@
-From 5186a4610a8ba9a485a398991c67dc4de7a6f2cd Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Wed, 17 Jun 2015 16:07:06 +0100
-Subject: [PATCH] vc_mem: Add vc_mem driver
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Signed-off-by: popcornmix <popcornmix at gmail.com>
-
-BCM270x: Move vc_mem
-
-Make the vc_mem module available for ARCH_BCM2835 by moving it.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
----
- arch/arm/mach-bcm2709/include/mach/vc_mem.h | 35 ---
- arch/arm/mach-bcm2709/vc_mem.c | 431 ----------------------------
- drivers/char/broadcom/Kconfig | 12 +-
- drivers/char/broadcom/Makefile | 1 +
- drivers/char/broadcom/vc_mem.c | 422 +++++++++++++++++++++++++++
- include/linux/broadcom/vc_mem.h | 35 +++
- 6 files changed, 469 insertions(+), 467 deletions(-)
- delete mode 100644 arch/arm/mach-bcm2709/include/mach/vc_mem.h
- delete mode 100644 arch/arm/mach-bcm2709/vc_mem.c
- create mode 100644 drivers/char/broadcom/vc_mem.c
- create mode 100644 include/linux/broadcom/vc_mem.h
-
---- a/arch/arm/mach-bcm2709/include/mach/vc_mem.h
-+++ /dev/null
-@@ -1,35 +0,0 @@
--/*****************************************************************************
--* Copyright 2010 - 2011 Broadcom Corporation. All rights reserved.
--*
--* Unless you and Broadcom execute a separate written software license
--* agreement governing use of this software, this software is licensed to you
--* under the terms of the GNU General Public License version 2, available at
--* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
--*
--* Notwithstanding the above, under no circumstances may you combine this
--* software in any way with any other Broadcom software provided under a
--* license other than the GPL, without Broadcom's express prior written
--* consent.
--*****************************************************************************/
--
--#if !defined( VC_MEM_H )
--#define VC_MEM_H
--
--#include <linux/ioctl.h>
--
--#define VC_MEM_IOC_MAGIC 'v'
--
--#define VC_MEM_IOC_MEM_PHYS_ADDR _IOR( VC_MEM_IOC_MAGIC, 0, unsigned long )
--#define VC_MEM_IOC_MEM_SIZE _IOR( VC_MEM_IOC_MAGIC, 1, unsigned int )
--#define VC_MEM_IOC_MEM_BASE _IOR( VC_MEM_IOC_MAGIC, 2, unsigned int )
--#define VC_MEM_IOC_MEM_LOAD _IOR( VC_MEM_IOC_MAGIC, 3, unsigned int )
--
--#if defined( __KERNEL__ )
--#define VC_MEM_TO_ARM_ADDR_MASK 0x3FFFFFFF
--
--extern unsigned long mm_vc_mem_phys_addr;
--extern unsigned int mm_vc_mem_size;
--extern int vc_mem_get_current_size( void );
--#endif
--
--#endif /* VC_MEM_H */
---- a/arch/arm/mach-bcm2709/vc_mem.c
-+++ /dev/null
-@@ -1,431 +0,0 @@
--/*****************************************************************************
--* Copyright 2010 - 2011 Broadcom Corporation. All rights reserved.
--*
--* Unless you and Broadcom execute a separate written software license
--* agreement governing use of this software, this software is licensed to you
--* under the terms of the GNU General Public License version 2, available at
--* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
--*
--* Notwithstanding the above, under no circumstances may you combine this
--* software in any way with any other Broadcom software provided under a
--* license other than the GPL, without Broadcom's express prior written
--* consent.
--*****************************************************************************/
--
--#include <linux/kernel.h>
--#include <linux/module.h>
--#include <linux/fs.h>
--#include <linux/device.h>
--#include <linux/cdev.h>
--#include <linux/mm.h>
--#include <linux/slab.h>
--#include <linux/debugfs.h>
--#include <asm/uaccess.h>
--#include <linux/dma-mapping.h>
--#include <linux/platform_data/mailbox-bcm2708.h>
--
--#ifdef CONFIG_ARCH_KONA
--#include <chal/chal_ipc.h>
--#elif defined(CONFIG_ARCH_BCM2708) || defined(CONFIG_ARCH_BCM2709)
--#else
--#include <csp/chal_ipc.h>
--#endif
--
--#include "mach/vc_mem.h"
--
--#define DRIVER_NAME "vc-mem"
--
--// Device (/dev) related variables
--static dev_t vc_mem_devnum = 0;
--static struct class *vc_mem_class = NULL;
--static struct cdev vc_mem_cdev;
--static int vc_mem_inited = 0;
--
--#ifdef CONFIG_DEBUG_FS
--static struct dentry *vc_mem_debugfs_entry;
--#endif
--
--/*
-- * Videocore memory addresses and size
-- *
-- * Drivers that wish to know the videocore memory addresses and sizes should
-- * use these variables instead of the MM_IO_BASE and MM_ADDR_IO defines in
-- * headers. This allows the other drivers to not be tied down to a a certain
-- * address/size at compile time.
-- *
-- * In the future, the goal is to have the videocore memory virtual address and
-- * size be calculated at boot time rather than at compile time. The decision of
-- * where the videocore memory resides and its size would be in the hands of the
-- * bootloader (and/or kernel). When that happens, the values of these variables
-- * would be calculated and assigned in the init function.
-- */
--// in the 2835 VC in mapped above ARM, but ARM has full access to VC space
--unsigned long mm_vc_mem_phys_addr = 0x00000000;
--unsigned int mm_vc_mem_size = 0;
--unsigned int mm_vc_mem_base = 0;
--
--EXPORT_SYMBOL(mm_vc_mem_phys_addr);
--EXPORT_SYMBOL(mm_vc_mem_size);
--EXPORT_SYMBOL(mm_vc_mem_base);
--
--static uint phys_addr = 0;
--static uint mem_size = 0;
--static uint mem_base = 0;
--
--
--/****************************************************************************
--*
--* vc_mem_open
--*
--***************************************************************************/
--
--static int
--vc_mem_open(struct inode *inode, struct file *file)
--{
-- (void) inode;
-- (void) file;
--
-- pr_debug("%s: called file = 0x%p\n", __func__, file);
--
-- return 0;
--}
--
--/****************************************************************************
--*
--* vc_mem_release
--*
--***************************************************************************/
--
--static int
--vc_mem_release(struct inode *inode, struct file *file)
--{
-- (void) inode;
-- (void) file;
--
-- pr_debug("%s: called file = 0x%p\n", __func__, file);
--
-- return 0;
--}
--
--/****************************************************************************
--*
--* vc_mem_get_size
--*
--***************************************************************************/
--
--static void
--vc_mem_get_size(void)
--{
--}
--
--/****************************************************************************
--*
--* vc_mem_get_base
--*
--***************************************************************************/
--
--static void
--vc_mem_get_base(void)
--{
--}
--
--/****************************************************************************
--*
--* vc_mem_get_current_size
--*
--***************************************************************************/
--
--int
--vc_mem_get_current_size(void)
--{
-- return mm_vc_mem_size;
--}
--
--EXPORT_SYMBOL_GPL(vc_mem_get_current_size);
--
--/****************************************************************************
--*
--* vc_mem_ioctl
--*
--***************************************************************************/
--
--static long
--vc_mem_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
--{
-- int rc = 0;
--
-- (void) cmd;
-- (void) arg;
--
-- pr_debug("%s: called file = 0x%p\n", __func__, file);
--
-- switch (cmd) {
-- case VC_MEM_IOC_MEM_PHYS_ADDR:
-- {
-- pr_debug("%s: VC_MEM_IOC_MEM_PHYS_ADDR=0x%p\n",
-- __func__, (void *) mm_vc_mem_phys_addr);
--
-- if (copy_to_user((void *) arg, &mm_vc_mem_phys_addr,
-- sizeof (mm_vc_mem_phys_addr)) != 0) {
-- rc = -EFAULT;
-- }
-- break;
-- }
-- case VC_MEM_IOC_MEM_SIZE:
-- {
-- // Get the videocore memory size first
-- vc_mem_get_size();
--
-- pr_debug("%s: VC_MEM_IOC_MEM_SIZE=%u\n", __func__,
-- mm_vc_mem_size);
--
-- if (copy_to_user((void *) arg, &mm_vc_mem_size,
-- sizeof (mm_vc_mem_size)) != 0) {
-- rc = -EFAULT;
-- }
-- break;
-- }
-- case VC_MEM_IOC_MEM_BASE:
-- {
-- // Get the videocore memory base
-- vc_mem_get_base();
--
-- pr_debug("%s: VC_MEM_IOC_MEM_BASE=%u\n", __func__,
-- mm_vc_mem_base);
--
-- if (copy_to_user((void *) arg, &mm_vc_mem_base,
-- sizeof (mm_vc_mem_base)) != 0) {
-- rc = -EFAULT;
-- }
-- break;
-- }
-- case VC_MEM_IOC_MEM_LOAD:
-- {
-- // Get the videocore memory base
-- vc_mem_get_base();
--
-- pr_debug("%s: VC_MEM_IOC_MEM_LOAD=%u\n", __func__,
-- mm_vc_mem_base);
--
-- if (copy_to_user((void *) arg, &mm_vc_mem_base,
-- sizeof (mm_vc_mem_base)) != 0) {
-- rc = -EFAULT;
-- }
-- break;
-- }
-- default:
-- {
-- return -ENOTTY;
-- }
-- }
-- pr_debug("%s: file = 0x%p returning %d\n", __func__, file, rc);
--
-- return rc;
--}
--
--/****************************************************************************
--*
--* vc_mem_mmap
--*
--***************************************************************************/
--
--static int
--vc_mem_mmap(struct file *filp, struct vm_area_struct *vma)
--{
-- int rc = 0;
-- unsigned long length = vma->vm_end - vma->vm_start;
-- unsigned long offset = vma->vm_pgoff << PAGE_SHIFT;
--
-- pr_debug("%s: vm_start = 0x%08lx vm_end = 0x%08lx vm_pgoff = 0x%08lx\n",
-- __func__, (long) vma->vm_start, (long) vma->vm_end,
-- (long) vma->vm_pgoff);
--
-- if (offset + length > mm_vc_mem_size) {
-- pr_err("%s: length %ld is too big\n", __func__, length);
-- return -EINVAL;
-- }
-- // Do not cache the memory map
-- vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
--
-- rc = remap_pfn_range(vma, vma->vm_start,
-- (mm_vc_mem_phys_addr >> PAGE_SHIFT) +
-- vma->vm_pgoff, length, vma->vm_page_prot);
-- if (rc != 0) {
-- pr_err("%s: remap_pfn_range failed (rc=%d)\n", __func__, rc);
-- }
--
-- return rc;
--}
--
--/****************************************************************************
--*
--* File Operations for the driver.
--*
--***************************************************************************/
--
--static const struct file_operations vc_mem_fops = {
-- .owner = THIS_MODULE,
-- .open = vc_mem_open,
-- .release = vc_mem_release,
-- .unlocked_ioctl = vc_mem_ioctl,
-- .mmap = vc_mem_mmap,
--};
--
--#ifdef CONFIG_DEBUG_FS
--static void vc_mem_debugfs_deinit(void)
--{
-- debugfs_remove_recursive(vc_mem_debugfs_entry);
-- vc_mem_debugfs_entry = NULL;
--}
--
--
--static int vc_mem_debugfs_init(
-- struct device *dev)
--{
-- vc_mem_debugfs_entry = debugfs_create_dir(DRIVER_NAME, NULL);
-- if (!vc_mem_debugfs_entry) {
-- dev_warn(dev, "could not create debugfs entry\n");
-- return -EFAULT;
-- }
--
-- if (!debugfs_create_x32("vc_mem_phys_addr",
-- 0444,
-- vc_mem_debugfs_entry,
-- (u32 *)&mm_vc_mem_phys_addr)) {
-- dev_warn(dev, "%s:could not create vc_mem_phys entry\n",
-- __func__);
-- goto fail;
-- }
--
-- if (!debugfs_create_x32("vc_mem_size",
-- 0444,
-- vc_mem_debugfs_entry,
-- (u32 *)&mm_vc_mem_size)) {
-- dev_warn(dev, "%s:could not create vc_mem_size entry\n",
-- __func__);
-- goto fail;
-- }
--
-- if (!debugfs_create_x32("vc_mem_base",
-- 0444,
-- vc_mem_debugfs_entry,
-- (u32 *)&mm_vc_mem_base)) {
-- dev_warn(dev, "%s:could not create vc_mem_base entry\n",
-- __func__);
-- goto fail;
-- }
--
-- return 0;
--
--fail:
-- vc_mem_debugfs_deinit();
-- return -EFAULT;
--}
--
--#endif /* CONFIG_DEBUG_FS */
--
--
--/****************************************************************************
--*
--* vc_mem_init
--*
--***************************************************************************/
--
--static int __init
--vc_mem_init(void)
--{
-- int rc = -EFAULT;
-- struct device *dev;
--
-- pr_debug("%s: called\n", __func__);
--
-- mm_vc_mem_phys_addr = phys_addr;
-- mm_vc_mem_size = mem_size;
-- mm_vc_mem_base = mem_base;
--
-- vc_mem_get_size();
--
-- pr_info("vc-mem: phys_addr:0x%08lx mem_base=0x%08x mem_size:0x%08x(%u MiB)\n",
-- mm_vc_mem_phys_addr, mm_vc_mem_base, mm_vc_mem_size, mm_vc_mem_size / (1024 * 1024));
--
-- if ((rc = alloc_chrdev_region(&vc_mem_devnum, 0, 1, DRIVER_NAME)) < 0) {
-- pr_err("%s: alloc_chrdev_region failed (rc=%d)\n",
-- __func__, rc);
-- goto out_err;
-- }
--
-- cdev_init(&vc_mem_cdev, &vc_mem_fops);
-- if ((rc = cdev_add(&vc_mem_cdev, vc_mem_devnum, 1)) != 0) {
-- pr_err("%s: cdev_add failed (rc=%d)\n", __func__, rc);
-- goto out_unregister;
-- }
--
-- vc_mem_class = class_create(THIS_MODULE, DRIVER_NAME);
-- if (IS_ERR(vc_mem_class)) {
-- rc = PTR_ERR(vc_mem_class);
-- pr_err("%s: class_create failed (rc=%d)\n", __func__, rc);
-- goto out_cdev_del;
-- }
--
-- dev = device_create(vc_mem_class, NULL, vc_mem_devnum, NULL,
-- DRIVER_NAME);
-- if (IS_ERR(dev)) {
-- rc = PTR_ERR(dev);
-- pr_err("%s: device_create failed (rc=%d)\n", __func__, rc);
-- goto out_class_destroy;
-- }
--
--#ifdef CONFIG_DEBUG_FS
-- /* don't fail if the debug entries cannot be created */
-- vc_mem_debugfs_init(dev);
--#endif
--
-- vc_mem_inited = 1;
-- return 0;
--
-- device_destroy(vc_mem_class, vc_mem_devnum);
--
-- out_class_destroy:
-- class_destroy(vc_mem_class);
-- vc_mem_class = NULL;
--
-- out_cdev_del:
-- cdev_del(&vc_mem_cdev);
--
-- out_unregister:
-- unregister_chrdev_region(vc_mem_devnum, 1);
--
-- out_err:
-- return -1;
--}
--
--/****************************************************************************
--*
--* vc_mem_exit
--*
--***************************************************************************/
--
--static void __exit
--vc_mem_exit(void)
--{
-- pr_debug("%s: called\n", __func__);
--
-- if (vc_mem_inited) {
--#if CONFIG_DEBUG_FS
-- vc_mem_debugfs_deinit();
--#endif
-- device_destroy(vc_mem_class, vc_mem_devnum);
-- class_destroy(vc_mem_class);
-- cdev_del(&vc_mem_cdev);
-- unregister_chrdev_region(vc_mem_devnum, 1);
-- }
--}
--
--module_init(vc_mem_init);
--module_exit(vc_mem_exit);
--MODULE_LICENSE("GPL");
--MODULE_AUTHOR("Broadcom Corporation");
--
--module_param(phys_addr, uint, 0644);
--module_param(mem_size, uint, 0644);
--module_param(mem_base, uint, 0644);
---- a/drivers/char/broadcom/Kconfig
-+++ b/drivers/char/broadcom/Kconfig
-@@ -7,9 +7,19 @@ menuconfig BRCM_CHAR_DRIVERS
- help
- Broadcom's char drivers
-
-+if BRCM_CHAR_DRIVERS
-+
- config BCM_VC_CMA
- bool "Videocore CMA"
-- depends on CMA && BRCM_CHAR_DRIVERS && BCM2708_VCHIQ
-+ depends on CMA && BCM2708_VCHIQ
- default n
- help
- Helper for videocore CMA access.
-+
-+config BCM2708_VCMEM
-+ bool "Videocore Memory"
-+ default y
-+ help
-+ Helper for videocore memory access and total size allocation.
-+
-+endif
---- a/drivers/char/broadcom/Makefile
-+++ b/drivers/char/broadcom/Makefile
-@@ -1 +1,2 @@
- obj-$(CONFIG_BCM_VC_CMA) += vc_cma/
-+obj-$(CONFIG_BCM2708_VCMEM) += vc_mem.o
---- /dev/null
-+++ b/drivers/char/broadcom/vc_mem.c
-@@ -0,0 +1,422 @@
-+/*****************************************************************************
-+* Copyright 2010 - 2011 Broadcom Corporation. All rights reserved.
-+*
-+* Unless you and Broadcom execute a separate written software license
-+* agreement governing use of this software, this software is licensed to you
-+* under the terms of the GNU General Public License version 2, available at
-+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
-+*
-+* Notwithstanding the above, under no circumstances may you combine this
-+* software in any way with any other Broadcom software provided under a
-+* license other than the GPL, without Broadcom's express prior written
-+* consent.
-+*****************************************************************************/
-+
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+#include <linux/fs.h>
-+#include <linux/device.h>
-+#include <linux/cdev.h>
-+#include <linux/mm.h>
-+#include <linux/slab.h>
-+#include <linux/debugfs.h>
-+#include <asm/uaccess.h>
-+#include <linux/dma-mapping.h>
-+#include <linux/broadcom/vc_mem.h>
-+
-+#define DRIVER_NAME "vc-mem"
-+
-+// Device (/dev) related variables
-+static dev_t vc_mem_devnum = 0;
-+static struct class *vc_mem_class = NULL;
-+static struct cdev vc_mem_cdev;
-+static int vc_mem_inited = 0;
-+
-+#ifdef CONFIG_DEBUG_FS
-+static struct dentry *vc_mem_debugfs_entry;
-+#endif
-+
-+/*
-+ * Videocore memory addresses and size
-+ *
-+ * Drivers that wish to know the videocore memory addresses and sizes should
-+ * use these variables instead of the MM_IO_BASE and MM_ADDR_IO defines in
-+ * headers. This allows the other drivers to not be tied down to a a certain
-+ * address/size at compile time.
-+ *
-+ * In the future, the goal is to have the videocore memory virtual address and
-+ * size be calculated at boot time rather than at compile time. The decision of
-+ * where the videocore memory resides and its size would be in the hands of the
-+ * bootloader (and/or kernel). When that happens, the values of these variables
-+ * would be calculated and assigned in the init function.
-+ */
-+// in the 2835 VC in mapped above ARM, but ARM has full access to VC space
-+unsigned long mm_vc_mem_phys_addr = 0x00000000;
-+unsigned int mm_vc_mem_size = 0;
-+unsigned int mm_vc_mem_base = 0;
-+
-+EXPORT_SYMBOL(mm_vc_mem_phys_addr);
-+EXPORT_SYMBOL(mm_vc_mem_size);
-+EXPORT_SYMBOL(mm_vc_mem_base);
-+
-+static uint phys_addr = 0;
-+static uint mem_size = 0;
-+static uint mem_base = 0;
-+
-+
-+/****************************************************************************
-+*
-+* vc_mem_open
-+*
-+***************************************************************************/
-+
-+static int
-+vc_mem_open(struct inode *inode, struct file *file)
-+{
-+ (void) inode;
-+ (void) file;
-+
-+ pr_debug("%s: called file = 0x%p\n", __func__, file);
-+
-+ return 0;
-+}
-+
-+/****************************************************************************
-+*
-+* vc_mem_release
-+*
-+***************************************************************************/
-+
-+static int
-+vc_mem_release(struct inode *inode, struct file *file)
-+{
-+ (void) inode;
-+ (void) file;
-+
-+ pr_debug("%s: called file = 0x%p\n", __func__, file);
-+
-+ return 0;
-+}
-+
-+/****************************************************************************
-+*
-+* vc_mem_get_size
-+*
-+***************************************************************************/
-+
-+static void
-+vc_mem_get_size(void)
-+{
-+}
-+
-+/****************************************************************************
-+*
-+* vc_mem_get_base
-+*
-+***************************************************************************/
-+
-+static void
-+vc_mem_get_base(void)
-+{
-+}
-+
-+/****************************************************************************
-+*
-+* vc_mem_get_current_size
-+*
-+***************************************************************************/
-+
-+int
-+vc_mem_get_current_size(void)
-+{
-+ return mm_vc_mem_size;
-+}
-+
-+EXPORT_SYMBOL_GPL(vc_mem_get_current_size);
-+
-+/****************************************************************************
-+*
-+* vc_mem_ioctl
-+*
-+***************************************************************************/
-+
-+static long
-+vc_mem_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
-+{
-+ int rc = 0;
-+
-+ (void) cmd;
-+ (void) arg;
-+
-+ pr_debug("%s: called file = 0x%p\n", __func__, file);
-+
-+ switch (cmd) {
-+ case VC_MEM_IOC_MEM_PHYS_ADDR:
-+ {
-+ pr_debug("%s: VC_MEM_IOC_MEM_PHYS_ADDR=0x%p\n",
-+ __func__, (void *) mm_vc_mem_phys_addr);
-+
-+ if (copy_to_user((void *) arg, &mm_vc_mem_phys_addr,
-+ sizeof (mm_vc_mem_phys_addr)) != 0) {
-+ rc = -EFAULT;
-+ }
-+ break;
-+ }
-+ case VC_MEM_IOC_MEM_SIZE:
-+ {
-+ // Get the videocore memory size first
-+ vc_mem_get_size();
-+
-+ pr_debug("%s: VC_MEM_IOC_MEM_SIZE=%u\n", __func__,
-+ mm_vc_mem_size);
-+
-+ if (copy_to_user((void *) arg, &mm_vc_mem_size,
-+ sizeof (mm_vc_mem_size)) != 0) {
-+ rc = -EFAULT;
-+ }
-+ break;
-+ }
-+ case VC_MEM_IOC_MEM_BASE:
-+ {
-+ // Get the videocore memory base
-+ vc_mem_get_base();
-+
-+ pr_debug("%s: VC_MEM_IOC_MEM_BASE=%u\n", __func__,
-+ mm_vc_mem_base);
-+
-+ if (copy_to_user((void *) arg, &mm_vc_mem_base,
-+ sizeof (mm_vc_mem_base)) != 0) {
-+ rc = -EFAULT;
-+ }
-+ break;
-+ }
-+ case VC_MEM_IOC_MEM_LOAD:
-+ {
-+ // Get the videocore memory base
-+ vc_mem_get_base();
-+
-+ pr_debug("%s: VC_MEM_IOC_MEM_LOAD=%u\n", __func__,
-+ mm_vc_mem_base);
-+
-+ if (copy_to_user((void *) arg, &mm_vc_mem_base,
-+ sizeof (mm_vc_mem_base)) != 0) {
-+ rc = -EFAULT;
-+ }
-+ break;
-+ }
-+ default:
-+ {
-+ return -ENOTTY;
-+ }
-+ }
-+ pr_debug("%s: file = 0x%p returning %d\n", __func__, file, rc);
-+
-+ return rc;
-+}
-+
-+/****************************************************************************
-+*
-+* vc_mem_mmap
-+*
-+***************************************************************************/
-+
-+static int
-+vc_mem_mmap(struct file *filp, struct vm_area_struct *vma)
-+{
-+ int rc = 0;
-+ unsigned long length = vma->vm_end - vma->vm_start;
-+ unsigned long offset = vma->vm_pgoff << PAGE_SHIFT;
-+
-+ pr_debug("%s: vm_start = 0x%08lx vm_end = 0x%08lx vm_pgoff = 0x%08lx\n",
-+ __func__, (long) vma->vm_start, (long) vma->vm_end,
-+ (long) vma->vm_pgoff);
-+
-+ if (offset + length > mm_vc_mem_size) {
-+ pr_err("%s: length %ld is too big\n", __func__, length);
-+ return -EINVAL;
-+ }
-+ // Do not cache the memory map
-+ vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
-+
-+ rc = remap_pfn_range(vma, vma->vm_start,
-+ (mm_vc_mem_phys_addr >> PAGE_SHIFT) +
-+ vma->vm_pgoff, length, vma->vm_page_prot);
-+ if (rc != 0) {
-+ pr_err("%s: remap_pfn_range failed (rc=%d)\n", __func__, rc);
-+ }
-+
-+ return rc;
-+}
-+
-+/****************************************************************************
-+*
-+* File Operations for the driver.
-+*
-+***************************************************************************/
-+
-+static const struct file_operations vc_mem_fops = {
-+ .owner = THIS_MODULE,
-+ .open = vc_mem_open,
-+ .release = vc_mem_release,
-+ .unlocked_ioctl = vc_mem_ioctl,
-+ .mmap = vc_mem_mmap,
-+};
-+
-+#ifdef CONFIG_DEBUG_FS
-+static void vc_mem_debugfs_deinit(void)
-+{
-+ debugfs_remove_recursive(vc_mem_debugfs_entry);
-+ vc_mem_debugfs_entry = NULL;
-+}
-+
-+
-+static int vc_mem_debugfs_init(
-+ struct device *dev)
-+{
-+ vc_mem_debugfs_entry = debugfs_create_dir(DRIVER_NAME, NULL);
-+ if (!vc_mem_debugfs_entry) {
-+ dev_warn(dev, "could not create debugfs entry\n");
-+ return -EFAULT;
-+ }
-+
-+ if (!debugfs_create_x32("vc_mem_phys_addr",
-+ 0444,
-+ vc_mem_debugfs_entry,
-+ (u32 *)&mm_vc_mem_phys_addr)) {
-+ dev_warn(dev, "%s:could not create vc_mem_phys entry\n",
-+ __func__);
-+ goto fail;
-+ }
-+
-+ if (!debugfs_create_x32("vc_mem_size",
-+ 0444,
-+ vc_mem_debugfs_entry,
-+ (u32 *)&mm_vc_mem_size)) {
-+ dev_warn(dev, "%s:could not create vc_mem_size entry\n",
-+ __func__);
-+ goto fail;
-+ }
-+
-+ if (!debugfs_create_x32("vc_mem_base",
-+ 0444,
-+ vc_mem_debugfs_entry,
-+ (u32 *)&mm_vc_mem_base)) {
-+ dev_warn(dev, "%s:could not create vc_mem_base entry\n",
-+ __func__);
-+ goto fail;
-+ }
-+
-+ return 0;
-+
-+fail:
-+ vc_mem_debugfs_deinit();
-+ return -EFAULT;
-+}
-+
-+#endif /* CONFIG_DEBUG_FS */
-+
-+
-+/****************************************************************************
-+*
-+* vc_mem_init
-+*
-+***************************************************************************/
-+
-+static int __init
-+vc_mem_init(void)
-+{
-+ int rc = -EFAULT;
-+ struct device *dev;
-+
-+ pr_debug("%s: called\n", __func__);
-+
-+ mm_vc_mem_phys_addr = phys_addr;
-+ mm_vc_mem_size = mem_size;
-+ mm_vc_mem_base = mem_base;
-+
-+ vc_mem_get_size();
-+
-+ pr_info("vc-mem: phys_addr:0x%08lx mem_base=0x%08x mem_size:0x%08x(%u MiB)\n",
-+ mm_vc_mem_phys_addr, mm_vc_mem_base, mm_vc_mem_size, mm_vc_mem_size / (1024 * 1024));
-+
-+ if ((rc = alloc_chrdev_region(&vc_mem_devnum, 0, 1, DRIVER_NAME)) < 0) {
-+ pr_err("%s: alloc_chrdev_region failed (rc=%d)\n",
-+ __func__, rc);
-+ goto out_err;
-+ }
-+
-+ cdev_init(&vc_mem_cdev, &vc_mem_fops);
-+ if ((rc = cdev_add(&vc_mem_cdev, vc_mem_devnum, 1)) != 0) {
-+ pr_err("%s: cdev_add failed (rc=%d)\n", __func__, rc);
-+ goto out_unregister;
-+ }
-+
-+ vc_mem_class = class_create(THIS_MODULE, DRIVER_NAME);
-+ if (IS_ERR(vc_mem_class)) {
-+ rc = PTR_ERR(vc_mem_class);
-+ pr_err("%s: class_create failed (rc=%d)\n", __func__, rc);
-+ goto out_cdev_del;
-+ }
-+
-+ dev = device_create(vc_mem_class, NULL, vc_mem_devnum, NULL,
-+ DRIVER_NAME);
-+ if (IS_ERR(dev)) {
-+ rc = PTR_ERR(dev);
-+ pr_err("%s: device_create failed (rc=%d)\n", __func__, rc);
-+ goto out_class_destroy;
-+ }
-+
-+#ifdef CONFIG_DEBUG_FS
-+ /* don't fail if the debug entries cannot be created */
-+ vc_mem_debugfs_init(dev);
-+#endif
-+
-+ vc_mem_inited = 1;
-+ return 0;
-+
-+ device_destroy(vc_mem_class, vc_mem_devnum);
-+
-+ out_class_destroy:
-+ class_destroy(vc_mem_class);
-+ vc_mem_class = NULL;
-+
-+ out_cdev_del:
-+ cdev_del(&vc_mem_cdev);
-+
-+ out_unregister:
-+ unregister_chrdev_region(vc_mem_devnum, 1);
-+
-+ out_err:
-+ return -1;
-+}
-+
-+/****************************************************************************
-+*
-+* vc_mem_exit
-+*
-+***************************************************************************/
-+
-+static void __exit
-+vc_mem_exit(void)
-+{
-+ pr_debug("%s: called\n", __func__);
-+
-+ if (vc_mem_inited) {
-+#if CONFIG_DEBUG_FS
-+ vc_mem_debugfs_deinit();
-+#endif
-+ device_destroy(vc_mem_class, vc_mem_devnum);
-+ class_destroy(vc_mem_class);
-+ cdev_del(&vc_mem_cdev);
-+ unregister_chrdev_region(vc_mem_devnum, 1);
-+ }
-+}
-+
-+module_init(vc_mem_init);
-+module_exit(vc_mem_exit);
-+MODULE_LICENSE("GPL");
-+MODULE_AUTHOR("Broadcom Corporation");
-+
-+module_param(phys_addr, uint, 0644);
-+module_param(mem_size, uint, 0644);
-+module_param(mem_base, uint, 0644);
---- /dev/null
-+++ b/include/linux/broadcom/vc_mem.h
-@@ -0,0 +1,35 @@
-+/*****************************************************************************
-+* Copyright 2010 - 2011 Broadcom Corporation. All rights reserved.
-+*
-+* Unless you and Broadcom execute a separate written software license
-+* agreement governing use of this software, this software is licensed to you
-+* under the terms of the GNU General Public License version 2, available at
-+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
-+*
-+* Notwithstanding the above, under no circumstances may you combine this
-+* software in any way with any other Broadcom software provided under a
-+* license other than the GPL, without Broadcom's express prior written
-+* consent.
-+*****************************************************************************/
-+
-+#ifndef _VC_MEM_H
-+#define _VC_MEM_H
-+
-+#include <linux/ioctl.h>
-+
-+#define VC_MEM_IOC_MAGIC 'v'
-+
-+#define VC_MEM_IOC_MEM_PHYS_ADDR _IOR( VC_MEM_IOC_MAGIC, 0, unsigned long )
-+#define VC_MEM_IOC_MEM_SIZE _IOR( VC_MEM_IOC_MAGIC, 1, unsigned int )
-+#define VC_MEM_IOC_MEM_BASE _IOR( VC_MEM_IOC_MAGIC, 2, unsigned int )
-+#define VC_MEM_IOC_MEM_LOAD _IOR( VC_MEM_IOC_MAGIC, 3, unsigned int )
-+
-+#if defined( __KERNEL__ )
-+#define VC_MEM_TO_ARM_ADDR_MASK 0x3FFFFFFF
-+
-+extern unsigned long mm_vc_mem_phys_addr;
-+extern unsigned int mm_vc_mem_size;
-+extern int vc_mem_get_current_size( void );
-+#endif
-+
-+#endif /* _VC_MEM_H */
diff --git a/target/linux/brcm2708/patches-4.4/0038-vcsm-VideoCore-shared-memory-service-for-BCM2835.patch b/target/linux/brcm2708/patches-4.4/0038-vcsm-VideoCore-shared-memory-service-for-BCM2835.patch
deleted file mode 100644
index e525d28..0000000
--- a/target/linux/brcm2708/patches-4.4/0038-vcsm-VideoCore-shared-memory-service-for-BCM2835.patch
+++ /dev/null
@@ -1,4393 +0,0 @@
-From f00123f1c399aa71a7bd55391e53060a14bd79b2 Mon Sep 17 00:00:00 2001
-From: Tim Gover <tgover at broadcom.com>
-Date: Tue, 22 Jul 2014 15:41:04 +0100
-Subject: [PATCH] vcsm: VideoCore shared memory service for BCM2835
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Add experimental support for the VideoCore shared memory service.
-This allows user processes to allocate memory from VideoCore's
-GPU relocatable heap and mmap the buffers. Additionally, the memory
-handles can passed to other VideoCore services such as MMAL, OpenMax
-and DispmanX
-
-TODO
-* This driver was originally released for BCM28155 which has a different
- cache architecture to BCM2835. Consequently, in this release only
- uncached mappings are supported. However, there's no fundamental
- reason which cached mappings cannot be support or BCM2835
-* More refactoring is required to remove the typedefs.
-* Re-enable the some of the commented out debug-fs statistics which were
- disabled when migrating code from proc-fs.
-* There's a lot of code to support sharing of VCSM in order to support
- Android. This could probably done more cleanly or perhaps just
- removed.
-
-Signed-off-by: Tim Gover <timgover at gmail.com>
-
-config: Disable VC_SM for now to fix hang with cutdown kernel
-
-vcsm: Use boolean as it cannot be built as module
-
-On building the bcm_vc_sm as a module we get the following error:
-
-v7_dma_flush_range and do_munmap are undefined in vc-sm.ko.
-
-Fix by making it not an option to build as module
-
-vcsm: Add ioctl for custom cache flushing
-
-vc-sm: Move headers out of arch directory
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
----
- drivers/char/broadcom/Kconfig | 9 +
- drivers/char/broadcom/Makefile | 1 +
- drivers/char/broadcom/vc_sm/Makefile | 20 +
- drivers/char/broadcom/vc_sm/vc_sm_defs.h | 181 ++
- drivers/char/broadcom/vc_sm/vc_sm_knl.h | 55 +
- drivers/char/broadcom/vc_sm/vc_vchi_sm.c | 492 +++++
- drivers/char/broadcom/vc_sm/vc_vchi_sm.h | 82 +
- drivers/char/broadcom/vc_sm/vmcs_sm.c | 3211 ++++++++++++++++++++++++++++++
- include/linux/broadcom/vmcs_sm_ioctl.h | 248 +++
- 9 files changed, 4299 insertions(+)
- create mode 100644 drivers/char/broadcom/vc_sm/Makefile
- create mode 100644 drivers/char/broadcom/vc_sm/vc_sm_defs.h
- create mode 100644 drivers/char/broadcom/vc_sm/vc_sm_knl.h
- create mode 100644 drivers/char/broadcom/vc_sm/vc_vchi_sm.c
- create mode 100644 drivers/char/broadcom/vc_sm/vc_vchi_sm.h
- create mode 100644 drivers/char/broadcom/vc_sm/vmcs_sm.c
- create mode 100644 include/linux/broadcom/vmcs_sm_ioctl.h
-
---- a/drivers/char/broadcom/Kconfig
-+++ b/drivers/char/broadcom/Kconfig
-@@ -23,3 +23,12 @@ config BCM2708_VCMEM
- Helper for videocore memory access and total size allocation.
-
- endif
-+
-+config BCM_VC_SM
-+ bool "VMCS Shared Memory"
-+ depends on BCM2708_VCHIQ
-+ select BCM2708_VCMEM
-+ default n
-+ help
-+ Support for the VC shared memory on the Broadcom reference
-+ design. Uses the VCHIQ stack.
---- a/drivers/char/broadcom/Makefile
-+++ b/drivers/char/broadcom/Makefile
-@@ -1,2 +1,3 @@
- obj-$(CONFIG_BCM_VC_CMA) += vc_cma/
- obj-$(CONFIG_BCM2708_VCMEM) += vc_mem.o
-+obj-$(CONFIG_BCM_VC_SM) += vc_sm/
---- /dev/null
-+++ b/drivers/char/broadcom/vc_sm/Makefile
-@@ -0,0 +1,20 @@
-+EXTRA_CFLAGS += -Wall -Wstrict-prototypes -Wno-trigraphs -O2
-+
-+EXTRA_CFLAGS += -I"drivers/misc/vc04_services"
-+EXTRA_CFLAGS += -I"drivers/misc/vc04_services/interface/vchi"
-+EXTRA_CFLAGS += -I"drivers/misc/vc04_services/interface/vchiq_arm"
-+EXTRA_CFLAGS += -I"$(srctree)/fs/"
-+
-+EXTRA_CFLAGS += -DOS_ASSERT_FAILURE
-+EXTRA_CFLAGS += -D__STDC_VERSION=199901L
-+EXTRA_CFLAGS += -D__STDC_VERSION__=199901L
-+EXTRA_CFLAGS += -D__VCCOREVER__=0
-+EXTRA_CFLAGS += -D__KERNEL__
-+EXTRA_CFLAGS += -D__linux__
-+EXTRA_CFLAGS += -Werror
-+
-+obj-$(CONFIG_BCM_VC_SM) := vc-sm.o
-+
-+vc-sm-objs := \
-+ vmcs_sm.o \
-+ vc_vchi_sm.o
---- /dev/null
-+++ b/drivers/char/broadcom/vc_sm/vc_sm_defs.h
-@@ -0,0 +1,181 @@
-+/*****************************************************************************
-+* Copyright 2011 Broadcom Corporation. All rights reserved.
-+*
-+* Unless you and Broadcom execute a separate written software license
-+* agreement governing use of this software, this software is licensed to you
-+* under the terms of the GNU General Public License version 2, available at
-+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
-+*
-+* Notwithstanding the above, under no circumstances may you combine this
-+* software in any way with any other Broadcom software provided under a
-+* license other than the GPL, without Broadcom's express prior written
-+* consent.
-+*****************************************************************************/
-+
-+#ifndef __VC_SM_DEFS_H__INCLUDED__
-+#define __VC_SM_DEFS_H__INCLUDED__
-+
-+/* FourCC code used for VCHI connection */
-+#define VC_SM_SERVER_NAME MAKE_FOURCC("SMEM")
-+
-+/* Maximum message length */
-+#define VC_SM_MAX_MSG_LEN (sizeof(VC_SM_MSG_UNION_T) + \
-+ sizeof(VC_SM_MSG_HDR_T))
-+#define VC_SM_MAX_RSP_LEN (sizeof(VC_SM_MSG_UNION_T))
-+
-+/* Resource name maximum size */
-+#define VC_SM_RESOURCE_NAME 32
-+
-+/* All message types supported for HOST->VC direction */
-+typedef enum {
-+ /* Allocate shared memory block */
-+ VC_SM_MSG_TYPE_ALLOC,
-+ /* Lock allocated shared memory block */
-+ VC_SM_MSG_TYPE_LOCK,
-+ /* Unlock allocated shared memory block */
-+ VC_SM_MSG_TYPE_UNLOCK,
-+ /* Unlock allocated shared memory block, do not answer command */
-+ VC_SM_MSG_TYPE_UNLOCK_NOANS,
-+ /* Free shared memory block */
-+ VC_SM_MSG_TYPE_FREE,
-+ /* Resize a shared memory block */
-+ VC_SM_MSG_TYPE_RESIZE,
-+ /* Walk the allocated shared memory block(s) */
-+ VC_SM_MSG_TYPE_WALK_ALLOC,
-+
-+ /* A previously applied action will need to be reverted */
-+ VC_SM_MSG_TYPE_ACTION_CLEAN,
-+ VC_SM_MSG_TYPE_MAX
-+} VC_SM_MSG_TYPE;
-+
-+/* Type of memory to be allocated */
-+typedef enum {
-+ VC_SM_ALLOC_CACHED,
-+ VC_SM_ALLOC_NON_CACHED,
-+
-+} VC_SM_ALLOC_TYPE_T;
-+
-+/* Message header for all messages in HOST->VC direction */
-+typedef struct {
-+ int32_t type;
-+ uint32_t trans_id;
-+ uint8_t body[0];
-+
-+} VC_SM_MSG_HDR_T;
-+
-+/* Request to allocate memory (HOST->VC) */
-+typedef struct {
-+ /* type of memory to allocate */
-+ VC_SM_ALLOC_TYPE_T type;
-+ /* byte amount of data to allocate per unit */
-+ uint32_t base_unit;
-+ /* number of unit to allocate */
-+ uint32_t num_unit;
-+ /* alignement to be applied on allocation */
-+ uint32_t alignement;
-+ /* identity of who allocated this block */
-+ uint32_t allocator;
-+ /* resource name (for easier tracking on vc side) */
-+ char name[VC_SM_RESOURCE_NAME];
-+
-+} VC_SM_ALLOC_T;
-+
-+/* Result of a requested memory allocation (VC->HOST) */
-+typedef struct {
-+ /* Transaction identifier */
-+ uint32_t trans_id;
-+
-+ /* Resource handle */
-+ uint32_t res_handle;
-+ /* Pointer to resource buffer */
-+ void *res_mem;
-+ /* Resource base size (bytes) */
-+ uint32_t res_base_size;
-+ /* Resource number */
-+ uint32_t res_num;
-+
-+} VC_SM_ALLOC_RESULT_T;
-+
-+/* Request to free a previously allocated memory (HOST->VC) */
-+typedef struct {
-+ /* Resource handle (returned from alloc) */
-+ uint32_t res_handle;
-+ /* Resource buffer (returned from alloc) */
-+ void *res_mem;
-+
-+} VC_SM_FREE_T;
-+
-+/* Request to lock a previously allocated memory (HOST->VC) */
-+typedef struct {
-+ /* Resource handle (returned from alloc) */
-+ uint32_t res_handle;
-+ /* Resource buffer (returned from alloc) */
-+ void *res_mem;
-+
-+} VC_SM_LOCK_UNLOCK_T;
-+
-+/* Request to resize a previously allocated memory (HOST->VC) */
-+typedef struct {
-+ /* Resource handle (returned from alloc) */
-+ uint32_t res_handle;
-+ /* Resource buffer (returned from alloc) */
-+ void *res_mem;
-+ /* Resource *new* size requested (bytes) */
-+ uint32_t res_new_size;
-+
-+} VC_SM_RESIZE_T;
-+
-+/* Result of a requested memory lock (VC->HOST) */
-+typedef struct {
-+ /* Transaction identifier */
-+ uint32_t trans_id;
-+
-+ /* Resource handle */
-+ uint32_t res_handle;
-+ /* Pointer to resource buffer */
-+ void *res_mem;
-+ /* Pointer to former resource buffer if the memory
-+ * was reallocated */
-+ void *res_old_mem;
-+
-+} VC_SM_LOCK_RESULT_T;
-+
-+/* Generic result for a request (VC->HOST) */
-+typedef struct {
-+ /* Transaction identifier */
-+ uint32_t trans_id;
-+
-+ int32_t success;
-+
-+} VC_SM_RESULT_T;
-+
-+/* Request to revert a previously applied action (HOST->VC) */
-+typedef struct {
-+ /* Action of interest */
-+ VC_SM_MSG_TYPE res_action;
-+ /* Transaction identifier for the action of interest */
-+ uint32_t action_trans_id;
-+
-+} VC_SM_ACTION_CLEAN_T;
-+
-+/* Request to remove all data associated with a given allocator (HOST->VC) */
-+typedef struct {
-+ /* Allocator identifier */
-+ uint32_t allocator;
-+
-+} VC_SM_FREE_ALL_T;
-+
-+/* Union of ALL messages */
-+typedef union {
-+ VC_SM_ALLOC_T alloc;
-+ VC_SM_ALLOC_RESULT_T alloc_result;
-+ VC_SM_FREE_T free;
-+ VC_SM_ACTION_CLEAN_T action_clean;
-+ VC_SM_RESIZE_T resize;
-+ VC_SM_LOCK_RESULT_T lock_result;
-+ VC_SM_RESULT_T result;
-+ VC_SM_FREE_ALL_T free_all;
-+
-+} VC_SM_MSG_UNION_T;
-+
-+#endif /* __VC_SM_DEFS_H__INCLUDED__ */
---- /dev/null
-+++ b/drivers/char/broadcom/vc_sm/vc_sm_knl.h
-@@ -0,0 +1,55 @@
-+/*****************************************************************************
-+* Copyright 2011 Broadcom Corporation. All rights reserved.
-+*
-+* Unless you and Broadcom execute a separate written software license
-+* agreement governing use of this software, this software is licensed to you
-+* under the terms of the GNU General Public License version 2, available at
-+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
-+*
-+* Notwithstanding the above, under no circumstances may you combine this
-+* software in any way with any other Broadcom software provided under a
-+* license other than the GPL, without Broadcom's express prior written
-+* consent.
-+*****************************************************************************/
-+
-+#ifndef __VC_SM_KNL_H__INCLUDED__
-+#define __VC_SM_KNL_H__INCLUDED__
-+
-+#if !defined(__KERNEL__)
-+#error "This interface is for kernel use only..."
-+#endif
-+
-+/* Type of memory to be locked (ie mapped) */
-+typedef enum {
-+ VC_SM_LOCK_CACHED,
-+ VC_SM_LOCK_NON_CACHED,
-+
-+} VC_SM_LOCK_CACHE_MODE_T;
-+
-+/* Allocate a shared memory handle and block.
-+*/
-+int vc_sm_alloc(VC_SM_ALLOC_T *alloc, int *handle);
-+
-+/* Free a previously allocated shared memory handle and block.
-+*/
-+int vc_sm_free(int handle);
-+
-+/* Lock a memory handle for use by kernel.
-+*/
-+int vc_sm_lock(int handle, VC_SM_LOCK_CACHE_MODE_T mode,
-+ long unsigned int *data);
-+
-+/* Unlock a memory handle in use by kernel.
-+*/
-+int vc_sm_unlock(int handle, int flush, int no_vc_unlock);
-+
-+/* Get an internal resource handle mapped from the external one.
-+*/
-+int vc_sm_int_handle(int handle);
-+
-+/* Map a shared memory region for use by kernel.
-+*/
-+int vc_sm_map(int handle, unsigned int sm_addr, VC_SM_LOCK_CACHE_MODE_T mode,
-+ long unsigned int *data);
-+
-+#endif /* __VC_SM_KNL_H__INCLUDED__ */
---- /dev/null
-+++ b/drivers/char/broadcom/vc_sm/vc_vchi_sm.c
-@@ -0,0 +1,492 @@
-+/*****************************************************************************
-+* Copyright 2011-2012 Broadcom Corporation. All rights reserved.
-+*
-+* Unless you and Broadcom execute a separate written software license
-+* agreement governing use of this software, this software is licensed to you
-+* under the terms of the GNU General Public License version 2, available at
-+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
-+*
-+* Notwithstanding the above, under no circumstances may you combine this
-+* software in any way with any other Broadcom software provided under a
-+* license other than the GPL, without Broadcom's express prior written
-+* consent.
-+*****************************************************************************/
-+
-+/* ---- Include Files ----------------------------------------------------- */
-+#include <linux/types.h>
-+#include <linux/kernel.h>
-+#include <linux/list.h>
-+#include <linux/semaphore.h>
-+#include <linux/mutex.h>
-+#include <linux/slab.h>
-+#include <linux/kthread.h>
-+
-+#include "vc_vchi_sm.h"
-+
-+#define VC_SM_VER 1
-+#define VC_SM_MIN_VER 0
-+
-+/* ---- Private Constants and Types -------------------------------------- */
-+
-+/* Command blocks come from a pool */
-+#define SM_MAX_NUM_CMD_RSP_BLKS 32
-+
-+struct sm_cmd_rsp_blk {
-+ struct list_head head; /* To create lists */
-+ struct semaphore sema; /* To be signaled when the response is there */
-+
-+ uint16_t id;
-+ uint16_t length;
-+
-+ uint8_t msg[VC_SM_MAX_MSG_LEN];
-+
-+ uint32_t wait:1;
-+ uint32_t sent:1;
-+ uint32_t alloc:1;
-+
-+};
-+
-+struct sm_instance {
-+ uint32_t num_connections;
-+ VCHI_SERVICE_HANDLE_T vchi_handle[VCHI_MAX_NUM_CONNECTIONS];
-+ struct task_struct *io_thread;
-+ struct semaphore io_sema;
-+
-+ uint32_t trans_id;
-+
-+ struct mutex lock;
-+ struct list_head cmd_list;
-+ struct list_head rsp_list;
-+ struct list_head dead_list;
-+
-+ struct sm_cmd_rsp_blk free_blk[SM_MAX_NUM_CMD_RSP_BLKS];
-+ struct list_head free_list;
-+ struct mutex free_lock;
-+ struct semaphore free_sema;
-+
-+};
-+
-+/* ---- Private Variables ------------------------------------------------ */
-+
-+/* ---- Private Function Prototypes -------------------------------------- */
-+
-+/* ---- Private Functions ------------------------------------------------ */
-+static struct
-+sm_cmd_rsp_blk *vc_vchi_cmd_create(struct sm_instance *instance,
-+ VC_SM_MSG_TYPE id, void *msg,
-+ uint32_t size, int wait)
-+{
-+ struct sm_cmd_rsp_blk *blk;
-+ VC_SM_MSG_HDR_T *hdr;
-+
-+ if (down_interruptible(&instance->free_sema)) {
-+ blk = kmalloc(sizeof(*blk), GFP_KERNEL);
-+ if (!blk)
-+ return NULL;
-+
-+ blk->alloc = 1;
-+ sema_init(&blk->sema, 0);
-+ } else {
-+ mutex_lock(&instance->free_lock);
-+ blk =
-+ list_first_entry(&instance->free_list,
-+ struct sm_cmd_rsp_blk, head);
-+ list_del(&blk->head);
-+ mutex_unlock(&instance->free_lock);
-+ }
-+
-+ blk->sent = 0;
-+ blk->wait = wait;
-+ blk->length = sizeof(*hdr) + size;
-+
-+ hdr = (VC_SM_MSG_HDR_T *) blk->msg;
-+ hdr->type = id;
-+ mutex_lock(&instance->lock);
-+ hdr->trans_id = blk->id = ++instance->trans_id;
-+ mutex_unlock(&instance->lock);
-+
-+ if (size)
-+ memcpy(hdr->body, msg, size);
-+
-+ return blk;
-+}
-+
-+static void
-+vc_vchi_cmd_delete(struct sm_instance *instance, struct sm_cmd_rsp_blk *blk)
-+{
-+ if (blk->alloc) {
-+ kfree(blk);
-+ return;
-+ }
-+
-+ mutex_lock(&instance->free_lock);
-+ list_add(&blk->head, &instance->free_list);
-+ mutex_unlock(&instance->free_lock);
-+ up(&instance->free_sema);
-+}
-+
-+static int vc_vchi_sm_videocore_io(void *arg)
-+{
-+ struct sm_instance *instance = arg;
-+ struct sm_cmd_rsp_blk *cmd = NULL, *cmd_tmp;
-+ VC_SM_RESULT_T *reply;
-+ uint32_t reply_len;
-+ int32_t status;
-+ int svc_use = 1;
-+
-+ while (1) {
-+ if (svc_use)
-+ vchi_service_release(instance->vchi_handle[0]);
-+ svc_use = 0;
-+ if (!down_interruptible(&instance->io_sema)) {
-+ vchi_service_use(instance->vchi_handle[0]);
-+ svc_use = 1;
-+
-+ do {
-+ unsigned int flags;
-+ /*
-+ * Get new command and move it to response list
-+ */
-+ mutex_lock(&instance->lock);
-+ if (list_empty(&instance->cmd_list)) {
-+ /* no more commands to process */
-+ mutex_unlock(&instance->lock);
-+ break;
-+ }
-+ cmd =
-+ list_first_entry(&instance->cmd_list,
-+ struct sm_cmd_rsp_blk,
-+ head);
-+ list_move(&cmd->head, &instance->rsp_list);
-+ cmd->sent = 1;
-+ mutex_unlock(&instance->lock);
-+
-+ /* Send the command */
-+ flags = VCHI_FLAGS_BLOCK_UNTIL_QUEUED;
-+ status = vchi_msg_queue(
-+ instance->vchi_handle[0],
-+ cmd->msg, cmd->length,
-+ flags, NULL);
-+ if (status) {
-+ pr_err("%s: failed to queue message (%d)",
-+ __func__, status);
-+ }
-+
-+ /* If no reply is needed then we're done */
-+ if (!cmd->wait) {
-+ mutex_lock(&instance->lock);
-+ list_del(&cmd->head);
-+ mutex_unlock(&instance->lock);
-+ vc_vchi_cmd_delete(instance, cmd);
-+ continue;
-+ }
-+
-+ if (status) {
-+ up(&cmd->sema);
-+ continue;
-+ }
-+
-+ } while (1);
-+
-+ while (!vchi_msg_peek
-+ (instance->vchi_handle[0], (void **)&reply,
-+ &reply_len, VCHI_FLAGS_NONE)) {
-+ mutex_lock(&instance->lock);
-+ list_for_each_entry(cmd, &instance->rsp_list,
-+ head) {
-+ if (cmd->id == reply->trans_id)
-+ break;
-+ }
-+ mutex_unlock(&instance->lock);
-+
-+ if (&cmd->head == &instance->rsp_list) {
-+ pr_debug("%s: received response %u, throw away...",
-+ __func__, reply->trans_id);
-+ } else if (reply_len > sizeof(cmd->msg)) {
-+ pr_err("%s: reply too big (%u) %u, throw away...",
-+ __func__, reply_len,
-+ reply->trans_id);
-+ } else {
-+ memcpy(cmd->msg, reply, reply_len);
-+ up(&cmd->sema);
-+ }
-+
-+ vchi_msg_remove(instance->vchi_handle[0]);
-+ }
-+
-+ /* Go through the dead list and free them */
-+ mutex_lock(&instance->lock);
-+ list_for_each_entry_safe(cmd, cmd_tmp,
-+ &instance->dead_list, head) {
-+ list_del(&cmd->head);
-+ vc_vchi_cmd_delete(instance, cmd);
-+ }
-+ mutex_unlock(&instance->lock);
-+ }
-+ }
-+
-+ return 0;
-+}
-+
-+static void vc_sm_vchi_callback(void *param,
-+ const VCHI_CALLBACK_REASON_T reason,
-+ void *msg_handle)
-+{
-+ struct sm_instance *instance = param;
-+
-+ (void)msg_handle;
-+
-+ switch (reason) {
-+ case VCHI_CALLBACK_MSG_AVAILABLE:
-+ up(&instance->io_sema);
-+ break;
-+
-+ case VCHI_CALLBACK_SERVICE_CLOSED:
-+ pr_info("%s: service CLOSED!!", __func__);
-+ default:
-+ break;
-+ }
-+}
-+
-+VC_VCHI_SM_HANDLE_T vc_vchi_sm_init(VCHI_INSTANCE_T vchi_instance,
-+ VCHI_CONNECTION_T **vchi_connections,
-+ uint32_t num_connections)
-+{
-+ uint32_t i;
-+ struct sm_instance *instance;
-+ int status;
-+
-+ pr_debug("%s: start", __func__);
-+
-+ if (num_connections > VCHI_MAX_NUM_CONNECTIONS) {
-+ pr_err("%s: unsupported number of connections %u (max=%u)",
-+ __func__, num_connections, VCHI_MAX_NUM_CONNECTIONS);
-+
-+ goto err_null;
-+ }
-+ /* Allocate memory for this instance */
-+ instance = kzalloc(sizeof(*instance), GFP_KERNEL);
-+
-+ /* Misc initialisations */
-+ mutex_init(&instance->lock);
-+ sema_init(&instance->io_sema, 0);
-+ INIT_LIST_HEAD(&instance->cmd_list);
-+ INIT_LIST_HEAD(&instance->rsp_list);
-+ INIT_LIST_HEAD(&instance->dead_list);
-+ INIT_LIST_HEAD(&instance->free_list);
-+ sema_init(&instance->free_sema, SM_MAX_NUM_CMD_RSP_BLKS);
-+ mutex_init(&instance->free_lock);
-+ for (i = 0; i < SM_MAX_NUM_CMD_RSP_BLKS; i++) {
-+ sema_init(&instance->free_blk[i].sema, 0);
-+ list_add(&instance->free_blk[i].head, &instance->free_list);
-+ }
-+
-+ /* Open the VCHI service connections */
-+ instance->num_connections = num_connections;
-+ for (i = 0; i < num_connections; i++) {
-+ SERVICE_CREATION_T params = {
-+ VCHI_VERSION_EX(VC_SM_VER, VC_SM_MIN_VER),
-+ VC_SM_SERVER_NAME,
-+ vchi_connections[i],
-+ 0,
-+ 0,
-+ vc_sm_vchi_callback,
-+ instance,
-+ 0,
-+ 0,
-+ 0,
-+ };
-+
-+ status = vchi_service_open(vchi_instance,
-+ ¶ms, &instance->vchi_handle[i]);
-+ if (status) {
-+ pr_err("%s: failed to open VCHI service (%d)",
-+ __func__, status);
-+
-+ goto err_close_services;
-+ }
-+ }
-+
-+ /* Create the thread which takes care of all io to/from videoocore. */
-+ instance->io_thread = kthread_create(&vc_vchi_sm_videocore_io,
-+ (void *)instance, "SMIO");
-+ if (instance->io_thread == NULL) {
-+ pr_err("%s: failed to create SMIO thread", __func__);
-+
-+ goto err_close_services;
-+ }
-+ set_user_nice(instance->io_thread, -10);
-+ wake_up_process(instance->io_thread);
-+
-+ pr_debug("%s: success - instance 0x%x", __func__, (unsigned)instance);
-+ return instance;
-+
-+err_close_services:
-+ for (i = 0; i < instance->num_connections; i++) {
-+ if (instance->vchi_handle[i] != NULL)
-+ vchi_service_close(instance->vchi_handle[i]);
-+ }
-+ kfree(instance);
-+err_null:
-+ pr_debug("%s: FAILED", __func__);
-+ return NULL;
-+}
-+
-+int vc_vchi_sm_stop(VC_VCHI_SM_HANDLE_T *handle)
-+{
-+ struct sm_instance *instance;
-+ uint32_t i;
-+
-+ if (handle == NULL) {
-+ pr_err("%s: invalid pointer to handle %p", __func__, handle);
-+ goto lock;
-+ }
-+
-+ if (*handle == NULL) {
-+ pr_err("%s: invalid handle %p", __func__, *handle);
-+ goto lock;
-+ }
-+
-+ instance = *handle;
-+
-+ /* Close all VCHI service connections */
-+ for (i = 0; i < instance->num_connections; i++) {
-+ int32_t success;
-+ vchi_service_use(instance->vchi_handle[i]);
-+
-+ success = vchi_service_close(instance->vchi_handle[i]);
-+ }
-+
-+ kfree(instance);
-+
-+ *handle = NULL;
-+ return 0;
-+
-+lock:
-+ return -EINVAL;
-+}
-+
-+int vc_vchi_sm_send_msg(VC_VCHI_SM_HANDLE_T handle,
-+ VC_SM_MSG_TYPE msg_id,
-+ void *msg, uint32_t msg_size,
-+ void *result, uint32_t result_size,
-+ uint32_t *cur_trans_id, uint8_t wait_reply)
-+{
-+ int status = 0;
-+ struct sm_instance *instance = handle;
-+ struct sm_cmd_rsp_blk *cmd_blk;
-+
-+ if (handle == NULL) {
-+ pr_err("%s: invalid handle", __func__);
-+ return -EINVAL;
-+ }
-+ if (msg == NULL) {
-+ pr_err("%s: invalid msg pointer", __func__);
-+ return -EINVAL;
-+ }
-+
-+ cmd_blk =
-+ vc_vchi_cmd_create(instance, msg_id, msg, msg_size, wait_reply);
-+ if (cmd_blk == NULL) {
-+ pr_err("[%s]: failed to allocate global tracking resource",
-+ __func__);
-+ return -ENOMEM;
-+ }
-+
-+ if (cur_trans_id != NULL)
-+ *cur_trans_id = cmd_blk->id;
-+
-+ mutex_lock(&instance->lock);
-+ list_add_tail(&cmd_blk->head, &instance->cmd_list);
-+ mutex_unlock(&instance->lock);
-+ up(&instance->io_sema);
-+
-+ if (!wait_reply)
-+ /* We're done */
-+ return 0;
-+
-+ /* Wait for the response */
-+ if (down_interruptible(&cmd_blk->sema)) {
-+ mutex_lock(&instance->lock);
-+ if (!cmd_blk->sent) {
-+ list_del(&cmd_blk->head);
-+ mutex_unlock(&instance->lock);
-+ vc_vchi_cmd_delete(instance, cmd_blk);
-+ return -ENXIO;
-+ }
-+ mutex_unlock(&instance->lock);
-+
-+ mutex_lock(&instance->lock);
-+ list_move(&cmd_blk->head, &instance->dead_list);
-+ mutex_unlock(&instance->lock);
-+ up(&instance->io_sema);
-+ return -EINTR; /* We're done */
-+ }
-+
-+ if (result && result_size) {
-+ memcpy(result, cmd_blk->msg, result_size);
-+ } else {
-+ VC_SM_RESULT_T *res = (VC_SM_RESULT_T *) cmd_blk->msg;
-+ status = (res->success == 0) ? 0 : -ENXIO;
-+ }
-+
-+ mutex_lock(&instance->lock);
-+ list_del(&cmd_blk->head);
-+ mutex_unlock(&instance->lock);
-+ vc_vchi_cmd_delete(instance, cmd_blk);
-+ return status;
-+}
-+
-+int vc_vchi_sm_alloc(VC_VCHI_SM_HANDLE_T handle, VC_SM_ALLOC_T *msg,
-+ VC_SM_ALLOC_RESULT_T *result, uint32_t *cur_trans_id)
-+{
-+ return vc_vchi_sm_send_msg(handle, VC_SM_MSG_TYPE_ALLOC,
-+ msg, sizeof(*msg), result, sizeof(*result),
-+ cur_trans_id, 1);
-+}
-+
-+int vc_vchi_sm_free(VC_VCHI_SM_HANDLE_T handle,
-+ VC_SM_FREE_T *msg, uint32_t *cur_trans_id)
-+{
-+ return vc_vchi_sm_send_msg(handle, VC_SM_MSG_TYPE_FREE,
-+ msg, sizeof(*msg), 0, 0, cur_trans_id, 0);
-+}
-+
-+int vc_vchi_sm_lock(VC_VCHI_SM_HANDLE_T handle,
-+ VC_SM_LOCK_UNLOCK_T *msg,
-+ VC_SM_LOCK_RESULT_T *result, uint32_t *cur_trans_id)
-+{
-+ return vc_vchi_sm_send_msg(handle, VC_SM_MSG_TYPE_LOCK,
-+ msg, sizeof(*msg), result, sizeof(*result),
-+ cur_trans_id, 1);
-+}
-+
-+int vc_vchi_sm_unlock(VC_VCHI_SM_HANDLE_T handle,
-+ VC_SM_LOCK_UNLOCK_T *msg,
-+ uint32_t *cur_trans_id, uint8_t wait_reply)
-+{
-+ return vc_vchi_sm_send_msg(handle, wait_reply ?
-+ VC_SM_MSG_TYPE_UNLOCK :
-+ VC_SM_MSG_TYPE_UNLOCK_NOANS, msg,
-+ sizeof(*msg), 0, 0, cur_trans_id,
-+ wait_reply);
-+}
-+
-+int vc_vchi_sm_resize(VC_VCHI_SM_HANDLE_T handle, VC_SM_RESIZE_T *msg,
-+ uint32_t *cur_trans_id)
-+{
-+ return vc_vchi_sm_send_msg(handle, VC_SM_MSG_TYPE_RESIZE,
-+ msg, sizeof(*msg), 0, 0, cur_trans_id, 1);
-+}
-+
-+int vc_vchi_sm_walk_alloc(VC_VCHI_SM_HANDLE_T handle)
-+{
-+ return vc_vchi_sm_send_msg(handle, VC_SM_MSG_TYPE_WALK_ALLOC,
-+ 0, 0, 0, 0, 0, 0);
-+}
-+
-+int vc_vchi_sm_clean_up(VC_VCHI_SM_HANDLE_T handle, VC_SM_ACTION_CLEAN_T *msg)
-+{
-+ return vc_vchi_sm_send_msg(handle, VC_SM_MSG_TYPE_ACTION_CLEAN,
-+ msg, sizeof(*msg), 0, 0, 0, 0);
-+}
---- /dev/null
-+++ b/drivers/char/broadcom/vc_sm/vc_vchi_sm.h
-@@ -0,0 +1,82 @@
-+/*****************************************************************************
-+* Copyright 2011 Broadcom Corporation. All rights reserved.
-+*
-+* Unless you and Broadcom execute a separate written software license
-+* agreement governing use of this software, this software is licensed to you
-+* under the terms of the GNU General Public License version 2, available at
-+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
-+*
-+* Notwithstanding the above, under no circumstances may you combine this
-+* software in any way with any other Broadcom software provided under a
-+* license other than the GPL, without Broadcom's express prior written
-+* consent.
-+*****************************************************************************/
-+
-+#ifndef __VC_VCHI_SM_H__INCLUDED__
-+#define __VC_VCHI_SM_H__INCLUDED__
-+
-+#include "interface/vchi/vchi.h"
-+
-+#include "vc_sm_defs.h"
-+
-+/* Forward declare.
-+*/
-+typedef struct sm_instance *VC_VCHI_SM_HANDLE_T;
-+
-+/* Initialize the shared memory service, opens up vchi connection to talk to it.
-+*/
-+VC_VCHI_SM_HANDLE_T vc_vchi_sm_init(VCHI_INSTANCE_T vchi_instance,
-+ VCHI_CONNECTION_T **vchi_connections,
-+ uint32_t num_connections);
-+
-+/* Terminates the shared memory service.
-+*/
-+int vc_vchi_sm_stop(VC_VCHI_SM_HANDLE_T *handle);
-+
-+/* Ask the shared memory service to allocate some memory on videocre and
-+** return the result of this allocation (which upon success will be a pointer
-+** to some memory in videocore space).
-+*/
-+int vc_vchi_sm_alloc(VC_VCHI_SM_HANDLE_T handle,
-+ VC_SM_ALLOC_T *alloc,
-+ VC_SM_ALLOC_RESULT_T *alloc_result, uint32_t *trans_id);
-+
-+/* Ask the shared memory service to free up some memory that was previously
-+** allocated by the vc_vchi_sm_alloc function call.
-+*/
-+int vc_vchi_sm_free(VC_VCHI_SM_HANDLE_T handle,
-+ VC_SM_FREE_T *free, uint32_t *trans_id);
-+
-+/* Ask the shared memory service to lock up some memory that was previously
-+** allocated by the vc_vchi_sm_alloc function call.
-+*/
-+int vc_vchi_sm_lock(VC_VCHI_SM_HANDLE_T handle,
-+ VC_SM_LOCK_UNLOCK_T *lock_unlock,
-+ VC_SM_LOCK_RESULT_T *lock_result, uint32_t *trans_id);
-+
-+/* Ask the shared memory service to unlock some memory that was previously
-+** allocated by the vc_vchi_sm_alloc function call.
-+*/
-+int vc_vchi_sm_unlock(VC_VCHI_SM_HANDLE_T handle,
-+ VC_SM_LOCK_UNLOCK_T *lock_unlock,
-+ uint32_t *trans_id, uint8_t wait_reply);
-+
-+/* Ask the shared memory service to resize some memory that was previously
-+** allocated by the vc_vchi_sm_alloc function call.
-+*/
-+int vc_vchi_sm_resize(VC_VCHI_SM_HANDLE_T handle,
-+ VC_SM_RESIZE_T *resize, uint32_t *trans_id);
-+
-+/* Walk the allocated resources on the videocore side, the allocation will
-+** show up in the log. This is purely for debug/information and takes no
-+** specific actions.
-+*/
-+int vc_vchi_sm_walk_alloc(VC_VCHI_SM_HANDLE_T handle);
-+
-+/* Clean up following a previously interrupted action which left the system
-+** in a bad state of some sort.
-+*/
-+int vc_vchi_sm_clean_up(VC_VCHI_SM_HANDLE_T handle,
-+ VC_SM_ACTION_CLEAN_T *action_clean);
-+
-+#endif /* __VC_VCHI_SM_H__INCLUDED__ */
---- /dev/null
-+++ b/drivers/char/broadcom/vc_sm/vmcs_sm.c
-@@ -0,0 +1,3211 @@
-+/*****************************************************************************
-+* Copyright 2011-2012 Broadcom Corporation. All rights reserved.
-+*
-+* Unless you and Broadcom execute a separate written software license
-+* agreement governing use of this software, this software is licensed to you
-+* under the terms of the GNU General Public License version 2, available at
-+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
-+*
-+* Notwithstanding the above, under no circumstances may you combine this
-+* software in any way with any other Broadcom software provided under a
-+* license other than the GPL, without Broadcom's express prior written
-+* consent.
-+*****************************************************************************/
-+
-+/* ---- Include Files ----------------------------------------------------- */
-+
-+#include <linux/cdev.h>
-+#include <linux/broadcom/vc_mem.h>
-+#include <linux/device.h>
-+#include <linux/debugfs.h>
-+#include <linux/dma-mapping.h>
-+#include <linux/errno.h>
-+#include <linux/fs.h>
-+#include <linux/hugetlb.h>
-+#include <linux/ioctl.h>
-+#include <linux/kernel.h>
-+#include <linux/list.h>
-+#include <linux/module.h>
-+#include <linux/mm.h>
-+#include <linux/pfn.h>
-+#include <linux/proc_fs.h>
-+#include <linux/pagemap.h>
-+#include <linux/semaphore.h>
-+#include <linux/slab.h>
-+#include <linux/seq_file.h>
-+#include <linux/types.h>
-+#include <asm/cacheflush.h>
-+
-+#include "vchiq_connected.h"
-+#include "vc_vchi_sm.h"
-+
-+#include <linux/broadcom/vmcs_sm_ioctl.h>
-+#include "vc_sm_knl.h"
-+
-+/* ---- Private Constants and Types --------------------------------------- */
-+
-+#define DEVICE_NAME "vcsm"
-+#define DEVICE_MINOR 0
-+
-+#define VC_SM_DIR_ROOT_NAME "vc-smem"
-+#define VC_SM_DIR_ALLOC_NAME "alloc"
-+#define VC_SM_STATE "state"
-+#define VC_SM_STATS "statistics"
-+#define VC_SM_RESOURCES "resources"
-+#define VC_SM_DEBUG "debug"
-+#define VC_SM_WRITE_BUF_SIZE 128
-+
-+/* Statistics tracked per resource and globally.
-+*/
-+enum SM_STATS_T {
-+ /* Attempt. */
-+ ALLOC,
-+ FREE,
-+ LOCK,
-+ UNLOCK,
-+ MAP,
-+ FLUSH,
-+ INVALID,
-+
-+ END_ATTEMPT,
-+
-+ /* Failure. */
-+ ALLOC_FAIL,
-+ FREE_FAIL,
-+ LOCK_FAIL,
-+ UNLOCK_FAIL,
-+ MAP_FAIL,
-+ FLUSH_FAIL,
-+ INVALID_FAIL,
-+
-+ END_ALL,
-+
-+};
-+
-+static const char *const sm_stats_human_read[] = {
-+ "Alloc",
-+ "Free",
-+ "Lock",
-+ "Unlock",
-+ "Map",
-+ "Cache Flush",
-+ "Cache Invalidate",
-+};
-+
-+typedef int (*VC_SM_SHOW) (struct seq_file *s, void *v);
-+struct SM_PDE_T {
-+ VC_SM_SHOW show; /* Debug fs function hookup. */
-+ struct dentry *dir_entry; /* Debug fs directory entry. */
-+ void *priv_data; /* Private data */
-+
-+};
-+
-+/* Single resource allocation tracked for all devices.
-+*/
-+struct sm_mmap {
-+ struct list_head map_list; /* Linked list of maps. */
-+
-+ struct SM_RESOURCE_T *resource; /* Pointer to the resource. */
-+
-+ pid_t res_pid; /* PID owning that resource. */
-+ unsigned int res_vc_hdl; /* Resource handle (videocore). */
-+ unsigned int res_usr_hdl; /* Resource handle (user). */
-+
-+ long unsigned int res_addr; /* Mapped virtual address. */
-+ struct vm_area_struct *vma; /* VM area for this mapping. */
-+ unsigned int ref_count; /* Reference count to this vma. */
-+
-+ /* Used to link maps associated with a resource. */
-+ struct list_head resource_map_list;
-+};
-+
-+/* Single resource allocation tracked for each opened device.
-+*/
-+struct SM_RESOURCE_T {
-+ struct list_head resource_list; /* List of resources. */
-+ struct list_head global_resource_list; /* Global list of resources. */
-+
-+ pid_t pid; /* PID owning that resource. */
-+ uint32_t res_guid; /* Unique identifier. */
-+ uint32_t lock_count; /* Lock count for this resource. */
-+ uint32_t ref_count; /* Ref count for this resource. */
-+
-+ uint32_t res_handle; /* Resource allocation handle. */
-+ void *res_base_mem; /* Resource base memory address. */
-+ uint32_t res_size; /* Resource size allocated. */
-+ enum vmcs_sm_cache_e res_cached; /* Resource cache type. */
-+ struct SM_RESOURCE_T *res_shared; /* Shared resource */
-+
-+ enum SM_STATS_T res_stats[END_ALL]; /* Resource statistics. */
-+
-+ uint8_t map_count; /* Counter of mappings for this resource. */
-+ struct list_head map_list; /* Maps associated with a resource. */
-+
-+ struct SM_PRIV_DATA_T *private;
-+};
-+
-+/* Private file data associated with each opened device.
-+*/
-+struct SM_PRIV_DATA_T {
-+ struct list_head resource_list; /* List of resources. */
-+
-+ pid_t pid; /* PID of creator. */
-+
-+ struct dentry *dir_pid; /* Debug fs entries root. */
-+ struct SM_PDE_T dir_stats; /* Debug fs entries statistics sub-tree. */
-+ struct SM_PDE_T dir_res; /* Debug fs resource sub-tree. */
-+
-+ int restart_sys; /* Tracks restart on interrupt. */
-+ VC_SM_MSG_TYPE int_action; /* Interrupted action. */
-+ uint32_t int_trans_id; /* Interrupted transaction. */
-+
-+};
-+
-+/* Global state information.
-+*/
-+struct SM_STATE_T {
-+ VC_VCHI_SM_HANDLE_T sm_handle; /* Handle for videocore service. */
-+ struct dentry *dir_root; /* Debug fs entries root. */
-+ struct dentry *dir_alloc; /* Debug fs entries allocations. */
-+ struct SM_PDE_T dir_stats; /* Debug fs entries statistics sub-tree. */
-+ struct SM_PDE_T dir_state; /* Debug fs entries state sub-tree. */
-+ struct dentry *debug; /* Debug fs entries debug. */
-+
-+ struct mutex map_lock; /* Global map lock. */
-+ struct list_head map_list; /* List of maps. */
-+ struct list_head resource_list; /* List of resources. */
-+
-+ enum SM_STATS_T deceased[END_ALL]; /* Natural termination stats. */
-+ enum SM_STATS_T terminated[END_ALL]; /* Forced termination stats. */
-+ uint32_t res_deceased_cnt; /* Natural termination counter. */
-+ uint32_t res_terminated_cnt; /* Forced termination counter. */
-+
-+ struct cdev sm_cdev; /* Device. */
-+ dev_t sm_devid; /* Device identifier. */
-+ struct class *sm_class; /* Class. */
-+ struct device *sm_dev; /* Device. */
-+
-+ struct SM_PRIV_DATA_T *data_knl; /* Kernel internal data tracking. */
-+
-+ struct mutex lock; /* Global lock. */
-+ uint32_t guid; /* GUID (next) tracker. */
-+
-+};
-+
-+/* ---- Private Variables ----------------------------------------------- */
-+
-+static struct SM_STATE_T *sm_state;
-+static int sm_inited;
-+
-+static const char *const sm_cache_map_vector[] = {
-+ "(null)",
-+ "host",
-+ "videocore",
-+ "host+videocore",
-+};
-+
-+/* ---- Private Function Prototypes -------------------------------------- */
-+
-+/* ---- Private Functions ------------------------------------------------ */
-+
-+static inline unsigned vcaddr_to_pfn(unsigned long vc_addr)
-+{
-+ unsigned long pfn = vc_addr & 0x3FFFFFFF;
-+ pfn += mm_vc_mem_phys_addr;
-+ pfn >>= PAGE_SHIFT;
-+ return pfn;
-+}
-+
-+/* Carries over to the state statistics the statistics once owned by a deceased
-+** resource.
-+*/
-+static void vc_sm_resource_deceased(struct SM_RESOURCE_T *p_res, int terminated)
-+{
-+ if (sm_state != NULL) {
-+ if (p_res != NULL) {
-+ int ix;
-+
-+ if (terminated)
-+ sm_state->res_terminated_cnt++;
-+ else
-+ sm_state->res_deceased_cnt++;
-+
-+ for (ix = 0; ix < END_ALL; ix++) {
-+ if (terminated)
-+ sm_state->terminated[ix] +=
-+ p_res->res_stats[ix];
-+ else
-+ sm_state->deceased[ix] +=
-+ p_res->res_stats[ix];
-+ }
-+ }
-+ }
-+}
-+
-+/* Fetch a videocore handle corresponding to a mapping of the pid+address
-+** returns 0 (ie NULL) if no such handle exists in the global map.
-+*/
-+static unsigned int vmcs_sm_vc_handle_from_pid_and_address(unsigned int pid,
-+ unsigned int addr)
-+{
-+ struct sm_mmap *map = NULL;
-+ unsigned int handle = 0;
-+
-+ if (!sm_state || addr == 0)
-+ goto out;
-+
-+ mutex_lock(&(sm_state->map_lock));
-+
-+ /* Lookup the resource.
-+ */
-+ if (!list_empty(&sm_state->map_list)) {
-+ list_for_each_entry(map, &sm_state->map_list, map_list) {
-+ if (map->res_pid != pid || map->res_addr != addr)
-+ continue;
-+
-+ pr_debug("[%s]: global map %p (pid %u, addr %lx) -> vc-hdl %x (usr-hdl %x)\n",
-+ __func__, map, map->res_pid, map->res_addr,
-+ map->res_vc_hdl, map->res_usr_hdl);
-+
-+ handle = map->res_vc_hdl;
-+ break;
-+ }
-+ }
-+
-+ mutex_unlock(&(sm_state->map_lock));
-+
-+out:
-+ /* Use a debug log here as it may be a valid situation that we query
-+ ** for something that is not mapped, we do not want a kernel log each
-+ ** time around.
-+ **
-+ ** There are other error log that would pop up accordingly if someone
-+ ** subsequently tries to use something invalid after being told not to
-+ ** use it...
-+ */
-+ if (handle == 0) {
-+ pr_debug("[%s]: not a valid map (pid %u, addr %x)\n",
-+ __func__, pid, addr);
-+ }
-+
-+ return handle;
-+}
-+
-+/* Fetch a user handle corresponding to a mapping of the pid+address
-+** returns 0 (ie NULL) if no such handle exists in the global map.
-+*/
-+static unsigned int vmcs_sm_usr_handle_from_pid_and_address(unsigned int pid,
-+ unsigned int addr)
-+{
-+ struct sm_mmap *map = NULL;
-+ unsigned int handle = 0;
-+
-+ if (!sm_state || addr == 0)
-+ goto out;
-+
-+ mutex_lock(&(sm_state->map_lock));
-+
-+ /* Lookup the resource.
-+ */
-+ if (!list_empty(&sm_state->map_list)) {
-+ list_for_each_entry(map, &sm_state->map_list, map_list) {
-+ if (map->res_pid != pid || map->res_addr != addr)
-+ continue;
-+
-+ pr_debug("[%s]: global map %p (pid %u, addr %lx) -> usr-hdl %x (vc-hdl %x)\n",
-+ __func__, map, map->res_pid, map->res_addr,
-+ map->res_usr_hdl, map->res_vc_hdl);
-+
-+ handle = map->res_usr_hdl;
-+ break;
-+ }
-+ }
-+
-+ mutex_unlock(&(sm_state->map_lock));
-+
-+out:
-+ /* Use a debug log here as it may be a valid situation that we query
-+ * for something that is not mapped yet.
-+ *
-+ * There are other error log that would pop up accordingly if someone
-+ * subsequently tries to use something invalid after being told not to
-+ * use it...
-+ */
-+ if (handle == 0)
-+ pr_debug("[%s]: not a valid map (pid %u, addr %x)\n",
-+ __func__, pid, addr);
-+
-+ return handle;
-+}
-+
-+#if defined(DO_NOT_USE)
-+/* Fetch an address corresponding to a mapping of the pid+handle
-+** returns 0 (ie NULL) if no such address exists in the global map.
-+*/
-+static unsigned int vmcs_sm_usr_address_from_pid_and_vc_handle(unsigned int pid,
-+ unsigned int hdl)
-+{
-+ struct sm_mmap *map = NULL;
-+ unsigned int addr = 0;
-+
-+ if (sm_state == NULL || hdl == 0)
-+ goto out;
-+
-+ mutex_lock(&(sm_state->map_lock));
-+
-+ /* Lookup the resource.
-+ */
-+ if (!list_empty(&sm_state->map_list)) {
-+ list_for_each_entry(map, &sm_state->map_list, map_list) {
-+ if (map->res_pid != pid || map->res_vc_hdl != hdl)
-+ continue;
-+
-+ pr_debug("[%s]: global map %p (pid %u, vc-hdl %x, usr-hdl %x) -> addr %lx\n",
-+ __func__, map, map->res_pid, map->res_vc_hdl,
-+ map->res_usr_hdl, map->res_addr);
-+
-+ addr = map->res_addr;
-+ break;
-+ }
-+ }
-+
-+ mutex_unlock(&(sm_state->map_lock));
-+
-+out:
-+ /* Use a debug log here as it may be a valid situation that we query
-+ ** for something that is not mapped, we do not want a kernel log each
-+ ** time around.
-+ **
-+ ** There are other error log that would pop up accordingly if someone
-+ ** subsequently tries to use something invalid after being told not to
-+ ** use it...
-+ */
-+ if (addr == 0)
-+ pr_debug("[%s]: not a valid map (pid %u, hdl %x)\n",
-+ __func__, pid, hdl);
-+
-+ return addr;
-+}
-+#endif
-+
-+/* Fetch an address corresponding to a mapping of the pid+handle
-+** returns 0 (ie NULL) if no such address exists in the global map.
-+*/
-+static unsigned int vmcs_sm_usr_address_from_pid_and_usr_handle(unsigned int
-+ pid,
-+ unsigned int
-+ hdl)
-+{
-+ struct sm_mmap *map = NULL;
-+ unsigned int addr = 0;
-+
-+ if (sm_state == NULL || hdl == 0)
-+ goto out;
-+
-+ mutex_lock(&(sm_state->map_lock));
-+
-+ /* Lookup the resource.
-+ */
-+ if (!list_empty(&sm_state->map_list)) {
-+ list_for_each_entry(map, &sm_state->map_list, map_list) {
-+ if (map->res_pid != pid || map->res_usr_hdl != hdl)
-+ continue;
-+
-+ pr_debug("[%s]: global map %p (pid %u, vc-hdl %x, usr-hdl %x) -> addr %lx\n",
-+ __func__, map, map->res_pid, map->res_vc_hdl,
-+ map->res_usr_hdl, map->res_addr);
-+
-+ addr = map->res_addr;
-+ break;
-+ }
-+ }
-+
-+ mutex_unlock(&(sm_state->map_lock));
-+
-+out:
-+ /* Use a debug log here as it may be a valid situation that we query
-+ * for something that is not mapped, we do not want a kernel log each
-+ * time around.
-+ *
-+ * There are other error log that would pop up accordingly if someone
-+ * subsequently tries to use something invalid after being told not to
-+ * use it...
-+ */
-+ if (addr == 0)
-+ pr_debug("[%s]: not a valid map (pid %u, hdl %x)\n", __func__,
-+ pid, hdl);
-+
-+ return addr;
-+}
-+
-+/* Adds a resource mapping to the global data list.
-+*/
-+static void vmcs_sm_add_map(struct SM_STATE_T *state,
-+ struct SM_RESOURCE_T *resource, struct sm_mmap *map)
-+{
-+ mutex_lock(&(state->map_lock));
-+
-+ /* Add to the global list of mappings
-+ */
-+ list_add(&map->map_list, &state->map_list);
-+
-+ /* Add to the list of mappings for this resource
-+ */
-+ list_add(&map->resource_map_list, &resource->map_list);
-+ resource->map_count++;
-+
-+ mutex_unlock(&(state->map_lock));
-+
-+ pr_debug("[%s]: added map %p (pid %u, vc-hdl %x, usr-hdl %x, addr %lx)\n",
-+ __func__, map, map->res_pid, map->res_vc_hdl,
-+ map->res_usr_hdl, map->res_addr);
-+}
-+
-+/* Removes a resource mapping from the global data list.
-+*/
-+static void vmcs_sm_remove_map(struct SM_STATE_T *state,
-+ struct SM_RESOURCE_T *resource,
-+ struct sm_mmap *map)
-+{
-+ mutex_lock(&(state->map_lock));
-+
-+ /* Remove from the global list of mappings
-+ */
-+ list_del(&map->map_list);
-+
-+ /* Remove from the list of mapping for this resource
-+ */
-+ list_del(&map->resource_map_list);
-+ if (resource->map_count > 0)
-+ resource->map_count--;
-+
-+ mutex_unlock(&(state->map_lock));
-+
-+ pr_debug("[%s]: removed map %p (pid %d, vc-hdl %x, usr-hdl %x, addr %lx)\n",
-+ __func__, map, map->res_pid, map->res_vc_hdl, map->res_usr_hdl,
-+ map->res_addr);
-+
-+ kfree(map);
-+}
-+
-+/* Read callback for the global state proc entry.
-+*/
-+static int vc_sm_global_state_show(struct seq_file *s, void *v)
-+{
-+ struct sm_mmap *map = NULL;
-+ int map_count = 0;
-+
-+ if (sm_state == NULL)
-+ return 0;
-+
-+ seq_printf(s, "\nVC-ServiceHandle 0x%x\n",
-+ (unsigned int)sm_state->sm_handle);
-+
-+ /* Log all applicable mapping(s).
-+ */
-+
-+ mutex_lock(&(sm_state->map_lock));
-+
-+ if (!list_empty(&sm_state->map_list)) {
-+ list_for_each_entry(map, &sm_state->map_list, map_list) {
-+ map_count++;
-+
-+ seq_printf(s, "\nMapping 0x%x\n",
-+ (unsigned int)map);
-+ seq_printf(s, " TGID %u\n",
-+ map->res_pid);
-+ seq_printf(s, " VC-HDL 0x%x\n",
-+ map->res_vc_hdl);
-+ seq_printf(s, " USR-HDL 0x%x\n",
-+ map->res_usr_hdl);
-+ seq_printf(s, " USR-ADDR 0x%lx\n",
-+ map->res_addr);
-+ }
-+ }
-+
-+ mutex_unlock(&(sm_state->map_lock));
-+ seq_printf(s, "\n\nTotal map count: %d\n\n", map_count);
-+
-+ return 0;
-+}
-+
-+static int vc_sm_global_statistics_show(struct seq_file *s, void *v)
-+{
-+ int ix;
-+
-+ /* Global state tracked statistics.
-+ */
-+ if (sm_state != NULL) {
-+ seq_puts(s, "\nDeceased Resources Statistics\n");
-+
-+ seq_printf(s, "\nNatural Cause (%u occurences)\n",
-+ sm_state->res_deceased_cnt);
-+ for (ix = 0; ix < END_ATTEMPT; ix++) {
-+ if (sm_state->deceased[ix] > 0) {
-+ seq_printf(s, " %u\t%s\n",
-+ sm_state->deceased[ix],
-+ sm_stats_human_read[ix]);
-+ }
-+ }
-+ seq_puts(s, "\n");
-+ for (ix = 0; ix < END_ATTEMPT; ix++) {
-+ if (sm_state->deceased[ix + END_ATTEMPT] > 0) {
-+ seq_printf(s, " %u\tFAILED %s\n",
-+ sm_state->deceased[ix + END_ATTEMPT],
-+ sm_stats_human_read[ix]);
-+ }
-+ }
-+
-+ seq_printf(s, "\nForcefull (%u occurences)\n",
-+ sm_state->res_terminated_cnt);
-+ for (ix = 0; ix < END_ATTEMPT; ix++) {
-+ if (sm_state->terminated[ix] > 0) {
-+ seq_printf(s, " %u\t%s\n",
-+ sm_state->terminated[ix],
-+ sm_stats_human_read[ix]);
-+ }
-+ }
-+ seq_puts(s, "\n");
-+ for (ix = 0; ix < END_ATTEMPT; ix++) {
-+ if (sm_state->terminated[ix + END_ATTEMPT] > 0) {
-+ seq_printf(s, " %u\tFAILED %s\n",
-+ sm_state->terminated[ix +
-+ END_ATTEMPT],
-+ sm_stats_human_read[ix]);
-+ }
-+ }
-+ }
-+
-+ return 0;
-+}
-+
-+#if 0
-+/* Read callback for the statistics proc entry.
-+*/
-+static int vc_sm_statistics_show(struct seq_file *s, void *v)
-+{
-+ int ix;
-+ struct SM_PRIV_DATA_T *file_data;
-+ struct SM_RESOURCE_T *resource;
-+ int res_count = 0;
-+ struct SM_PDE_T *p_pde;
-+
-+ p_pde = (struct SM_PDE_T *)(s->private);
-+ file_data = (struct SM_PRIV_DATA_T *)(p_pde->priv_data);
-+
-+ if (file_data == NULL)
-+ return 0;
-+
-+ /* Per process statistics.
-+ */
-+
-+ seq_printf(s, "\nStatistics for TGID %d\n", file_data->pid);
-+
-+ mutex_lock(&(sm_state->map_lock));
-+
-+ if (!list_empty(&file_data->resource_list)) {
-+ list_for_each_entry(resource, &file_data->resource_list,
-+ resource_list) {
-+ res_count++;
-+
-+ seq_printf(s, "\nGUID: 0x%x\n\n",
-+ resource->res_guid);
-+ for (ix = 0; ix < END_ATTEMPT; ix++) {
-+ if (resource->res_stats[ix] > 0) {
-+ seq_printf(s,
-+ " %u\t%s\n",
-+ resource->res_stats[ix],
-+ sm_stats_human_read[ix]);
-+ }
-+ }
-+ seq_puts(s, "\n");
-+ for (ix = 0; ix < END_ATTEMPT; ix++) {
-+ if (resource->res_stats[ix + END_ATTEMPT] > 0) {
-+ seq_printf(s,
-+ " %u\tFAILED %s\n",
-+ resource->res_stats[
-+ ix + END_ATTEMPT],
-+ sm_stats_human_read[ix]);
-+ }
-+ }
-+ }
-+ }
-+
-+ mutex_unlock(&(sm_state->map_lock));
-+
-+ seq_printf(s, "\nResources Count %d\n", res_count);
-+
-+ return 0;
-+}
-+#endif
-+
-+#if 0
-+/* Read callback for the allocation proc entry. */
-+static int vc_sm_alloc_show(struct seq_file *s, void *v)
-+{
-+ struct SM_PRIV_DATA_T *file_data;
-+ struct SM_RESOURCE_T *resource;
-+ int alloc_count = 0;
-+ struct SM_PDE_T *p_pde;
-+
-+ p_pde = (struct SM_PDE_T *)(s->private);
-+ file_data = (struct SM_PRIV_DATA_T *)(p_pde->priv_data);
-+
-+ if (!file_data)
-+ return 0;
-+
-+ /* Per process statistics. */
-+ seq_printf(s, "\nAllocation for TGID %d\n", file_data->pid);
-+
-+ mutex_lock(&(sm_state->map_lock));
-+
-+ if (!list_empty(&file_data->resource_list)) {
-+ list_for_each_entry(resource, &file_data->resource_list,
-+ resource_list) {
-+ alloc_count++;
-+
-+ seq_printf(s, "\nGUID: 0x%x\n",
-+ resource->res_guid);
-+ seq_printf(s, "Lock Count: %u\n",
-+ resource->lock_count);
-+ seq_printf(s, "Mapped: %s\n",
-+ (resource->map_count ? "yes" : "no"));
-+ seq_printf(s, "VC-handle: 0x%x\n",
-+ resource->res_handle);
-+ seq_printf(s, "VC-address: 0x%p\n",
-+ resource->res_base_mem);
-+ seq_printf(s, "VC-size (bytes): %u\n",
-+ resource->res_size);
-+ seq_printf(s, "Cache: %s\n",
-+ sm_cache_map_vector[resource->res_cached]);
-+ }
-+ }
-+
-+ mutex_unlock(&(sm_state->map_lock));
-+
-+ seq_printf(s, "\n\nTotal allocation count: %d\n\n", alloc_count);
-+
-+ return 0;
-+}
-+#endif
-+
-+static int vc_sm_seq_file_show(struct seq_file *s, void *v)
-+{
-+ struct SM_PDE_T *sm_pde;
-+
-+ sm_pde = (struct SM_PDE_T *)(s->private);
-+
-+ if (sm_pde && sm_pde->show)
-+ sm_pde->show(s, v);
-+
-+ return 0;
-+}
-+
-+static int vc_sm_single_open(struct inode *inode, struct file *file)
-+{
-+ return single_open(file, vc_sm_seq_file_show, inode->i_private);
-+}
-+
-+static const struct file_operations vc_sm_debug_fs_fops = {
-+ .open = vc_sm_single_open,
-+ .read = seq_read,
-+ .llseek = seq_lseek,
-+ .release = single_release,
-+};
-+
-+/* Adds a resource to the private data list which tracks all the allocated
-+** data.
-+*/
-+static void vmcs_sm_add_resource(struct SM_PRIV_DATA_T *privdata,
-+ struct SM_RESOURCE_T *resource)
-+{
-+ mutex_lock(&(sm_state->map_lock));
-+ list_add(&resource->resource_list, &privdata->resource_list);
-+ list_add(&resource->global_resource_list, &sm_state->resource_list);
-+ mutex_unlock(&(sm_state->map_lock));
-+
-+ pr_debug("[%s]: added resource %p (base addr %p, hdl %x, size %u, cache %u)\n",
-+ __func__, resource, resource->res_base_mem,
-+ resource->res_handle, resource->res_size, resource->res_cached);
-+}
-+
-+/* Locates a resource and acquire a reference on it.
-+** The resource won't be deleted while there is a reference on it.
-+*/
-+static struct SM_RESOURCE_T *vmcs_sm_acquire_resource(struct SM_PRIV_DATA_T
-+ *private,
-+ unsigned int res_guid)
-+{
-+ struct SM_RESOURCE_T *resource, *ret = NULL;
-+
-+ mutex_lock(&(sm_state->map_lock));
-+
-+ list_for_each_entry(resource, &private->resource_list, resource_list) {
-+ if (resource->res_guid != res_guid)
-+ continue;
-+
-+ pr_debug("[%s]: located resource %p (guid: %x, base addr %p, hdl %x, size %u, cache %u)\n",
-+ __func__, resource, resource->res_guid,
-+ resource->res_base_mem, resource->res_handle,
-+ resource->res_size, resource->res_cached);
-+ resource->ref_count++;
-+ ret = resource;
-+ break;
-+ }
-+
-+ mutex_unlock(&(sm_state->map_lock));
-+
-+ return ret;
-+}
-+
-+/* Locates a resource and acquire a reference on it.
-+** The resource won't be deleted while there is a reference on it.
-+*/
-+static struct SM_RESOURCE_T *vmcs_sm_acquire_first_resource(
-+ struct SM_PRIV_DATA_T *private)
-+{
-+ struct SM_RESOURCE_T *resource, *ret = NULL;
-+
-+ mutex_lock(&(sm_state->map_lock));
-+
-+ list_for_each_entry(resource, &private->resource_list, resource_list) {
-+ pr_debug("[%s]: located resource %p (guid: %x, base addr %p, hdl %x, size %u, cache %u)\n",
-+ __func__, resource, resource->res_guid,
-+ resource->res_base_mem, resource->res_handle,
-+ resource->res_size, resource->res_cached);
-+ resource->ref_count++;
-+ ret = resource;
-+ break;
-+ }
-+
-+ mutex_unlock(&(sm_state->map_lock));
-+
-+ return ret;
-+}
-+
-+/* Locates a resource and acquire a reference on it.
-+** The resource won't be deleted while there is a reference on it.
-+*/
-+static struct SM_RESOURCE_T *vmcs_sm_acquire_global_resource(unsigned int
-+ res_guid)
-+{
-+ struct SM_RESOURCE_T *resource, *ret = NULL;
-+
-+ mutex_lock(&(sm_state->map_lock));
-+
-+ list_for_each_entry(resource, &sm_state->resource_list,
-+ global_resource_list) {
-+ if (resource->res_guid != res_guid)
-+ continue;
-+
-+ pr_debug("[%s]: located resource %p (guid: %x, base addr %p, hdl %x, size %u, cache %u)\n",
-+ __func__, resource, resource->res_guid,
-+ resource->res_base_mem, resource->res_handle,
-+ resource->res_size, resource->res_cached);
-+ resource->ref_count++;
-+ ret = resource;
-+ break;
-+ }
-+
-+ mutex_unlock(&(sm_state->map_lock));
-+
-+ return ret;
-+}
-+
-+/* Release a previously acquired resource.
-+** The resource will be deleted when its refcount reaches 0.
-+*/
-+static void vmcs_sm_release_resource(struct SM_RESOURCE_T *resource, int force)
-+{
-+ struct SM_PRIV_DATA_T *private = resource->private;
-+ struct sm_mmap *map, *map_tmp;
-+ struct SM_RESOURCE_T *res_tmp;
-+ int ret;
-+
-+ mutex_lock(&(sm_state->map_lock));
-+
-+ if (--resource->ref_count) {
-+ if (force)
-+ pr_err("[%s]: resource %p in use\n", __func__, resource);
-+
-+ mutex_unlock(&(sm_state->map_lock));
-+ return;
-+ }
-+
-+ /* Time to free the resource. Start by removing it from the list */
-+ list_del(&resource->resource_list);
-+ list_del(&resource->global_resource_list);
-+
-+ /* Walk the global resource list, find out if the resource is used
-+ * somewhere else. In which case we don't want to delete it.
-+ */
-+ list_for_each_entry(res_tmp, &sm_state->resource_list,
-+ global_resource_list) {
-+ if (res_tmp->res_handle == resource->res_handle) {
-+ resource->res_handle = 0;
-+ break;
-+ }
-+ }
-+
-+ mutex_unlock(&(sm_state->map_lock));
-+
-+ pr_debug("[%s]: freeing data - guid %x, hdl %x, base address %p\n",
-+ __func__, resource->res_guid, resource->res_handle,
-+ resource->res_base_mem);
-+ resource->res_stats[FREE]++;
-+
-+ /* Make sure the resource we're removing is unmapped first */
-+ if (resource->map_count && !list_empty(&resource->map_list)) {
-+ down_write(¤t->mm->mmap_sem);
-+ list_for_each_entry_safe(map, map_tmp, &resource->map_list,
-+ resource_map_list) {
-+ ret =
-+ do_munmap(current->mm, map->res_addr,
-+ resource->res_size);
-+ if (ret) {
-+ pr_err("[%s]: could not unmap resource %p\n",
-+ __func__, resource);
-+ }
-+ }
-+ up_write(¤t->mm->mmap_sem);
-+ }
-+
-+ /* Free up the videocore allocated resource.
-+ */
-+ if (resource->res_handle) {
-+ VC_SM_FREE_T free = {
-+ resource->res_handle, resource->res_base_mem
-+ };
-+ int status = vc_vchi_sm_free(sm_state->sm_handle, &free,
-+ &private->int_trans_id);
-+ if (status != 0 && status != -EINTR) {
-+ pr_err("[%s]: failed to free memory on videocore (status: %u, trans_id: %u)\n",
-+ __func__, status, private->int_trans_id);
-+ resource->res_stats[FREE_FAIL]++;
-+ ret = -EPERM;
-+ }
-+ }
-+
-+ /* Free up the shared resource.
-+ */
-+ if (resource->res_shared)
-+ vmcs_sm_release_resource(resource->res_shared, 0);
-+
-+ /* Free up the local resource tracking this allocation.
-+ */
-+ vc_sm_resource_deceased(resource, force);
-+ kfree(resource);
-+}
-+
-+/* Dump the map table for the driver. If process is -1, dumps the whole table,
-+** if process is a valid pid (non -1) dump only the entries associated with the
-+** pid of interest.
-+*/
-+static void vmcs_sm_host_walk_map_per_pid(int pid)
-+{
-+ struct sm_mmap *map = NULL;
-+
-+ /* Make sure the device was started properly.
-+ */
-+ if (sm_state == NULL) {
-+ pr_err("[%s]: invalid device\n", __func__);
-+ return;
-+ }
-+
-+ mutex_lock(&(sm_state->map_lock));
-+
-+ /* Log all applicable mapping(s).
-+ */
-+ if (!list_empty(&sm_state->map_list)) {
-+ list_for_each_entry(map, &sm_state->map_list, map_list) {
-+ if (pid == -1 || map->res_pid == pid) {
-+ pr_info("[%s]: tgid: %u - vc-hdl: %x, usr-hdl: %x, usr-addr: %lx\n",
-+ __func__, map->res_pid, map->res_vc_hdl,
-+ map->res_usr_hdl, map->res_addr);
-+ }
-+ }
-+ }
-+
-+ mutex_unlock(&(sm_state->map_lock));
-+
-+ return;
-+}
-+
-+/* Dump the allocation table from host side point of view. This only dumps the
-+** data allocated for this process/device referenced by the file_data.
-+*/
-+static void vmcs_sm_host_walk_alloc(struct SM_PRIV_DATA_T *file_data)
-+{
-+ struct SM_RESOURCE_T *resource = NULL;
-+
-+ /* Make sure the device was started properly.
-+ */
-+ if ((sm_state == NULL) || (file_data == NULL)) {
-+ pr_err("[%s]: invalid device\n", __func__);
-+ return;
-+ }
-+
-+ mutex_lock(&(sm_state->map_lock));
-+
-+ if (!list_empty(&file_data->resource_list)) {
-+ list_for_each_entry(resource, &file_data->resource_list,
-+ resource_list) {
-+ pr_info("[%s]: guid: %x - hdl: %x, vc-mem: %p, size: %u, cache: %u\n",
-+ __func__, resource->res_guid, resource->res_handle,
-+ resource->res_base_mem, resource->res_size,
-+ resource->res_cached);
-+ }
-+ }
-+
-+ mutex_unlock(&(sm_state->map_lock));
-+
-+ return;
-+}
-+
-+/* Create support for private data tracking.
-+*/
-+static struct SM_PRIV_DATA_T *vc_sm_create_priv_data(pid_t id)
-+{
-+ char alloc_name[32];
-+ struct SM_PRIV_DATA_T *file_data = NULL;
-+
-+ /* Allocate private structure. */
-+ file_data = kzalloc(sizeof(*file_data), GFP_KERNEL);
-+
-+ if (!file_data) {
-+ pr_err("[%s]: cannot allocate file data\n", __func__);
-+ goto out;
-+ }
-+
-+ snprintf(alloc_name, sizeof(alloc_name), "%d", id);
-+
-+ INIT_LIST_HEAD(&file_data->resource_list);
-+ file_data->pid = id;
-+ file_data->dir_pid = debugfs_create_dir(alloc_name,
-+ sm_state->dir_alloc);
-+#if 0
-+ /* TODO: fix this to support querying statistics per pid */
-+
-+ if (IS_ERR_OR_NULL(file_data->dir_pid)) {
-+ file_data->dir_pid = NULL;
-+ } else {
-+ struct dentry *dir_entry;
-+
-+ dir_entry = debugfs_create_file(VC_SM_RESOURCES, S_IRUGO,
-+ file_data->dir_pid, file_data,
-+ vc_sm_debug_fs_fops);
-+
-+ file_data->dir_res.dir_entry = dir_entry;
-+ file_data->dir_res.priv_data = file_data;
-+ file_data->dir_res.show = &vc_sm_alloc_show;
-+
-+ dir_entry = debugfs_create_file(VC_SM_STATS, S_IRUGO,
-+ file_data->dir_pid, file_data,
-+ vc_sm_debug_fs_fops);
-+
-+ file_data->dir_res.dir_entry = dir_entry;
-+ file_data->dir_res.priv_data = file_data;
-+ file_data->dir_res.show = &vc_sm_statistics_show;
-+ }
-+ pr_debug("[%s]: private data allocated %p\n", __func__, file_data);
-+
-+#endif
-+out:
-+ return file_data;
-+}
-+
-+/* Open the device. Creates a private state to help track all allocation
-+** associated with this device.
-+*/
-+static int vc_sm_open(struct inode *inode, struct file *file)
-+{
-+ int ret = 0;
-+
-+ /* Make sure the device was started properly.
-+ */
-+ if (!sm_state) {
-+ pr_err("[%s]: invalid device\n", __func__);
-+ ret = -EPERM;
-+ goto out;
-+ }
-+
-+ file->private_data = vc_sm_create_priv_data(current->tgid);
-+ if (file->private_data == NULL) {
-+ pr_err("[%s]: failed to create data tracker\n", __func__);
-+
-+ ret = -ENOMEM;
-+ goto out;
-+ }
-+
-+out:
-+ return ret;
-+}
-+
-+/* Close the device. Free up all resources still associated with this device
-+** at the time.
-+*/
-+static int vc_sm_release(struct inode *inode, struct file *file)
-+{
-+ struct SM_PRIV_DATA_T *file_data =
-+ (struct SM_PRIV_DATA_T *)file->private_data;
-+ struct SM_RESOURCE_T *resource;
-+ int ret = 0;
-+
-+ /* Make sure the device was started properly.
-+ */
-+ if (sm_state == NULL || file_data == NULL) {
-+ pr_err("[%s]: invalid device\n", __func__);
-+ ret = -EPERM;
-+ goto out;
-+ }
-+
-+ pr_debug("[%s]: using private data %p\n", __func__, file_data);
-+
-+ if (file_data->restart_sys == -EINTR) {
-+ VC_SM_ACTION_CLEAN_T action_clean;
-+
-+ pr_debug("[%s]: releasing following EINTR on %u (trans_id: %u) (likely due to signal)...\n",
-+ __func__, file_data->int_action,
-+ file_data->int_trans_id);
-+
-+ action_clean.res_action = file_data->int_action;
-+ action_clean.action_trans_id = file_data->int_trans_id;
-+
-+ vc_vchi_sm_clean_up(sm_state->sm_handle, &action_clean);
-+ }
-+
-+ while ((resource = vmcs_sm_acquire_first_resource(file_data)) != NULL) {
-+ vmcs_sm_release_resource(resource, 0);
-+ vmcs_sm_release_resource(resource, 1);
-+ }
-+
-+ /* Remove the corresponding proc entry. */
-+ debugfs_remove_recursive(file_data->dir_pid);
-+
-+ /* Terminate the private data.
-+ */
-+ kfree(file_data);
-+
-+out:
-+ return ret;
-+}
-+
-+static void vcsm_vma_open(struct vm_area_struct *vma)
-+{
-+ struct sm_mmap *map = (struct sm_mmap *)vma->vm_private_data;
-+
-+ pr_debug("[%s]: virt %lx-%lx, pid %i, pfn %i\n",
-+ __func__, vma->vm_start, vma->vm_end, (int)current->tgid,
-+ (int)vma->vm_pgoff);
-+
-+ map->ref_count++;
-+}
-+
-+static void vcsm_vma_close(struct vm_area_struct *vma)
-+{
-+ struct sm_mmap *map = (struct sm_mmap *)vma->vm_private_data;
-+
-+ pr_debug("[%s]: virt %lx-%lx, pid %i, pfn %i\n",
-+ __func__, vma->vm_start, vma->vm_end, (int)current->tgid,
-+ (int)vma->vm_pgoff);
-+
-+ map->ref_count--;
-+
-+ /* Remove from the map table.
-+ */
-+ if (map->ref_count == 0)
-+ vmcs_sm_remove_map(sm_state, map->resource, map);
-+}
-+
-+static int vcsm_vma_fault(struct vm_area_struct *vma, struct vm_fault *vmf)
-+{
-+ struct sm_mmap *map = (struct sm_mmap *)vma->vm_private_data;
-+ struct SM_RESOURCE_T *resource = map->resource;
-+ pgoff_t page_offset;
-+ unsigned long pfn;
-+ int ret = 0;
-+
-+ /* Lock the resource if necessary.
-+ */
-+ if (!resource->lock_count) {
-+ VC_SM_LOCK_UNLOCK_T lock_unlock;
-+ VC_SM_LOCK_RESULT_T lock_result;
-+ int status;
-+
-+ lock_unlock.res_handle = resource->res_handle;
-+ lock_unlock.res_mem = resource->res_base_mem;
-+
-+ pr_debug("[%s]: attempt to lock data - hdl %x, base address %p\n",
-+ __func__, lock_unlock.res_handle, lock_unlock.res_mem);
-+
-+ /* Lock the videocore allocated resource.
-+ */
-+ status = vc_vchi_sm_lock(sm_state->sm_handle,
-+ &lock_unlock, &lock_result, 0);
-+ if ((status != 0) ||
-+ ((status == 0) && (lock_result.res_mem == NULL))) {
-+ pr_err("[%s]: failed to lock memory on videocore (status: %u)\n",
-+ __func__, status);
-+ resource->res_stats[LOCK_FAIL]++;
-+ return VM_FAULT_SIGBUS;
-+ }
-+
-+ pfn = vcaddr_to_pfn((unsigned long)resource->res_base_mem);
-+ outer_inv_range(__pfn_to_phys(pfn),
-+ __pfn_to_phys(pfn) + resource->res_size);
-+
-+ resource->res_stats[LOCK]++;
-+ resource->lock_count++;
-+
-+ /* Keep track of the new base memory.
-+ */
-+ if ((lock_result.res_mem != NULL) &&
-+ (lock_result.res_old_mem != NULL) &&
-+ (lock_result.res_mem != lock_result.res_old_mem)) {
-+ resource->res_base_mem = lock_result.res_mem;
-+ }
-+ }
-+
-+ /* We don't use vmf->pgoff since that has the fake offset */
-+ page_offset = ((unsigned long)vmf->virtual_address - vma->vm_start);
-+ pfn = (uint32_t)resource->res_base_mem & 0x3FFFFFFF;
-+ pfn += mm_vc_mem_phys_addr;
-+ pfn += page_offset;
-+ pfn >>= PAGE_SHIFT;
-+
-+ /* Finally, remap it */
-+ ret = vm_insert_pfn(vma, (unsigned long)vmf->virtual_address, pfn);
-+
-+ switch (ret) {
-+ case 0:
-+ case -ERESTARTSYS:
-+ return VM_FAULT_NOPAGE;
-+ case -ENOMEM:
-+ case -EAGAIN:
-+ return VM_FAULT_OOM;
-+ default:
-+ return VM_FAULT_SIGBUS;
-+ }
-+}
-+
-+static struct vm_operations_struct vcsm_vm_ops = {
-+ .open = vcsm_vma_open,
-+ .close = vcsm_vma_close,
-+ .fault = vcsm_vma_fault,
-+};
-+
-+/* Walks a VMA and clean each valid page from the cache */
-+static void vcsm_vma_cache_clean_page_range(unsigned long addr,
-+ unsigned long end)
-+{
-+ pgd_t *pgd;
-+ pud_t *pud;
-+ pmd_t *pmd;
-+ pte_t *pte;
-+ unsigned long pgd_next, pud_next, pmd_next;
-+
-+ if (addr >= end)
-+ return;
-+
-+ /* Walk PGD */
-+ pgd = pgd_offset(current->mm, addr);
-+ do {
-+ pgd_next = pgd_addr_end(addr, end);
-+
-+ if (pgd_none(*pgd) || pgd_bad(*pgd))
-+ continue;
-+
-+ /* Walk PUD */
-+ pud = pud_offset(pgd, addr);
-+ do {
-+ pud_next = pud_addr_end(addr, pgd_next);
-+ if (pud_none(*pud) || pud_bad(*pud))
-+ continue;
-+
-+ /* Walk PMD */
-+ pmd = pmd_offset(pud, addr);
-+ do {
-+ pmd_next = pmd_addr_end(addr, pud_next);
-+ if (pmd_none(*pmd) || pmd_bad(*pmd))
-+ continue;
-+
-+ /* Walk PTE */
-+ pte = pte_offset_map(pmd, addr);
-+ do {
-+ if (pte_none(*pte)
-+ || !pte_present(*pte))
-+ continue;
-+
-+ /* Clean + invalidate */
-+ dmac_flush_range((const void *) addr,
-+ (const void *)
-+ (addr + PAGE_SIZE));
-+
-+ } while (pte++, addr +=
-+ PAGE_SIZE, addr != pmd_next);
-+ pte_unmap(pte);
-+
-+ } while (pmd++, addr = pmd_next, addr != pud_next);
-+
-+ } while (pud++, addr = pud_next, addr != pgd_next);
-+ } while (pgd++, addr = pgd_next, addr != end);
-+}
-+
-+/* Map an allocated data into something that the user space.
-+*/
-+static int vc_sm_mmap(struct file *file, struct vm_area_struct *vma)
-+{
-+ int ret = 0;
-+ struct SM_PRIV_DATA_T *file_data =
-+ (struct SM_PRIV_DATA_T *)file->private_data;
-+ struct SM_RESOURCE_T *resource = NULL;
-+ struct sm_mmap *map = NULL;
-+
-+ /* Make sure the device was started properly.
-+ */
-+ if ((sm_state == NULL) || (file_data == NULL)) {
-+ pr_err("[%s]: invalid device\n", __func__);
-+ return -EPERM;
-+ }
-+
-+ pr_debug("[%s]: private data %p, guid %x\n", __func__, file_data,
-+ ((unsigned int)vma->vm_pgoff << PAGE_SHIFT));
-+
-+ /* We lookup to make sure that the data we are being asked to mmap is
-+ ** something that we allocated.
-+ **
-+ ** We use the offset information as the key to tell us which resource
-+ ** we are mapping.
-+ */
-+ resource = vmcs_sm_acquire_resource(file_data,
-+ ((unsigned int)vma->vm_pgoff <<
-+ PAGE_SHIFT));
-+ if (resource == NULL) {
-+ pr_err("[%s]: failed to locate resource for guid %x\n", __func__,
-+ ((unsigned int)vma->vm_pgoff << PAGE_SHIFT));
-+ return -ENOMEM;
-+ }
-+
-+ pr_debug("[%s]: guid %x, tgid %u, %u, %u\n",
-+ __func__, resource->res_guid, current->tgid, resource->pid,
-+ file_data->pid);
-+
-+ /* Check permissions.
-+ */
-+ if (resource->pid && (resource->pid != current->tgid)) {
-+ pr_err("[%s]: current tgid %u != %u owner\n",
-+ __func__, current->tgid, resource->pid);
-+ ret = -EPERM;
-+ goto error;
-+ }
-+
-+ /* Verify that what we are asked to mmap is proper.
-+ */
-+ if (resource->res_size != (unsigned int)(vma->vm_end - vma->vm_start)) {
-+ pr_err("[%s]: size inconsistency (resource: %u - mmap: %u)\n",
-+ __func__,
-+ resource->res_size,
-+ (unsigned int)(vma->vm_end - vma->vm_start));
-+
-+ ret = -EINVAL;
-+ goto error;
-+ }
-+
-+ /* Keep track of the tuple in the global resource list such that one
-+ * can do a mapping lookup for address/memory handle.
-+ */
-+ map = kzalloc(sizeof(*map), GFP_KERNEL);
-+ if (map == NULL) {
-+ pr_err("[%s]: failed to allocate global tracking resource\n",
-+ __func__);
-+ ret = -ENOMEM;
-+ goto error;
-+ }
-+
-+ map->res_pid = current->tgid;
-+ map->res_vc_hdl = resource->res_handle;
-+ map->res_usr_hdl = resource->res_guid;
-+ map->res_addr = (long unsigned int)vma->vm_start;
-+ map->resource = resource;
-+ map->vma = vma;
-+ vmcs_sm_add_map(sm_state, resource, map);
-+
-+ /* We are not actually mapping the pages, we just provide a fault
-+ ** handler to allow pages to be mapped when accessed
-+ */
-+ vma->vm_flags |=
-+ VM_IO | VM_PFNMAP | VM_DONTCOPY | VM_DONTEXPAND;
-+ vma->vm_ops = &vcsm_vm_ops;
-+ vma->vm_private_data = map;
-+
-+ /* vm_pgoff is the first PFN of the mapped memory */
-+ vma->vm_pgoff = (unsigned long)resource->res_base_mem & 0x3FFFFFFF;
-+ vma->vm_pgoff += mm_vc_mem_phys_addr;
-+ vma->vm_pgoff >>= PAGE_SHIFT;
-+
-+ if ((resource->res_cached == VMCS_SM_CACHE_NONE) ||
-+ (resource->res_cached == VMCS_SM_CACHE_VC)) {
-+ /* Allocated non host cached memory, honour it.
-+ */
-+ vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
-+ }
-+
-+ pr_debug("[%s]: resource %p (guid %x) - cnt %u, base address %p, handle %x, size %u (%u), cache %u\n",
-+ __func__,
-+ resource, resource->res_guid, resource->lock_count,
-+ resource->res_base_mem, resource->res_handle,
-+ resource->res_size, (unsigned int)(vma->vm_end - vma->vm_start),
-+ resource->res_cached);
-+
-+ pr_debug("[%s]: resource %p (base address %p, handle %x) - map-count %d, usr-addr %x\n",
-+ __func__, resource, resource->res_base_mem,
-+ resource->res_handle, resource->map_count,
-+ (unsigned int)vma->vm_start);
-+
-+ vcsm_vma_open(vma);
-+ resource->res_stats[MAP]++;
-+ vmcs_sm_release_resource(resource, 0);
-+ return 0;
-+
-+error:
-+ resource->res_stats[MAP_FAIL]++;
-+ vmcs_sm_release_resource(resource, 0);
-+ return ret;
-+}
-+
-+/* Allocate a shared memory handle and block.
-+*/
-+int vc_sm_ioctl_alloc(struct SM_PRIV_DATA_T *private,
-+ struct vmcs_sm_ioctl_alloc *ioparam)
-+{
-+ int ret = 0;
-+ int status;
-+ struct SM_RESOURCE_T *resource;
-+ VC_SM_ALLOC_T alloc = { 0 };
-+ VC_SM_ALLOC_RESULT_T result = { 0 };
-+
-+ /* Setup our allocation parameters */
-+ alloc.type = ((ioparam->cached == VMCS_SM_CACHE_VC)
-+ || (ioparam->cached ==
-+ VMCS_SM_CACHE_BOTH)) ? VC_SM_ALLOC_CACHED :
-+ VC_SM_ALLOC_NON_CACHED;
-+ alloc.base_unit = ioparam->size;
-+ alloc.num_unit = ioparam->num;
-+ alloc.allocator = current->tgid;
-+ /* Align to kernel page size */
-+ alloc.alignement = 4096;
-+ /* Align the size to the kernel page size */
-+ alloc.base_unit =
-+ (alloc.base_unit + alloc.alignement - 1) & ~(alloc.alignement - 1);
-+ if (*ioparam->name) {
-+ memcpy(alloc.name, ioparam->name, sizeof(alloc.name) - 1);
-+ } else {
-+ memcpy(alloc.name, VMCS_SM_RESOURCE_NAME_DEFAULT,
-+ sizeof(VMCS_SM_RESOURCE_NAME_DEFAULT));
-+ }
-+
-+ pr_debug("[%s]: attempt to allocate \"%s\" data - type %u, base %u (%u), num %u, alignement %u\n",
-+ __func__, alloc.name, alloc.type, ioparam->size,
-+ alloc.base_unit, alloc.num_unit, alloc.alignement);
-+
-+ /* Allocate local resource to track this allocation.
-+ */
-+ resource = kzalloc(sizeof(*resource), GFP_KERNEL);
-+ if (!resource) {
-+ ret = -ENOMEM;
-+ goto error;
-+ }
-+ INIT_LIST_HEAD(&resource->map_list);
-+ resource->ref_count++;
-+ resource->pid = current->tgid;
-+
-+ /* Allocate the videocore resource.
-+ */
-+ status = vc_vchi_sm_alloc(sm_state->sm_handle, &alloc, &result,
-+ &private->int_trans_id);
-+ if (status == -EINTR) {
-+ pr_debug("[%s]: requesting allocate memory action restart (trans_id: %u)\n",
-+ __func__, private->int_trans_id);
-+ ret = -ERESTARTSYS;
-+ private->restart_sys = -EINTR;
-+ private->int_action = VC_SM_MSG_TYPE_ALLOC;
-+ goto error;
-+ } else if (status != 0 || (status == 0 && result.res_mem == NULL)) {
-+ pr_err("[%s]: failed to allocate memory on videocore (status: %u, trans_id: %u)\n",
-+ __func__, status, private->int_trans_id);
-+ ret = -ENOMEM;
-+ resource->res_stats[ALLOC_FAIL]++;
-+ goto error;
-+ }
-+
-+ /* Keep track of the resource we created.
-+ */
-+ resource->private = private;
-+ resource->res_handle = result.res_handle;
-+ resource->res_base_mem = result.res_mem;
-+ resource->res_size = alloc.base_unit * alloc.num_unit;
-+ resource->res_cached = ioparam->cached;
-+
-+ /* Kernel/user GUID. This global identifier is used for mmap'ing the
-+ * allocated region from user space, it is passed as the mmap'ing
-+ * offset, we use it to 'hide' the videocore handle/address.
-+ */
-+ mutex_lock(&sm_state->lock);
-+ resource->res_guid = ++sm_state->guid;
-+ mutex_unlock(&sm_state->lock);
-+ resource->res_guid <<= PAGE_SHIFT;
-+
-+ vmcs_sm_add_resource(private, resource);
-+
-+ pr_debug("[%s]: allocated data - guid %x, hdl %x, base address %p, size %d, cache %d\n",
-+ __func__, resource->res_guid, resource->res_handle,
-+ resource->res_base_mem, resource->res_size,
-+ resource->res_cached);
-+
-+ /* We're done */
-+ resource->res_stats[ALLOC]++;
-+ ioparam->handle = resource->res_guid;
-+ return 0;
-+
-+error:
-+ pr_err("[%s]: failed to allocate \"%s\" data (%i) - type %u, base %u (%u), num %u, alignment %u\n",
-+ __func__, alloc.name, ret, alloc.type, ioparam->size,
-+ alloc.base_unit, alloc.num_unit, alloc.alignement);
-+ if (resource != NULL) {
-+ vc_sm_resource_deceased(resource, 1);
-+ kfree(resource);
-+ }
-+ return ret;
-+}
-+
-+/* Share an allocate memory handle and block.
-+*/
-+int vc_sm_ioctl_alloc_share(struct SM_PRIV_DATA_T *private,
-+ struct vmcs_sm_ioctl_alloc_share *ioparam)
-+{
-+ struct SM_RESOURCE_T *resource, *shared_resource;
-+ int ret = 0;
-+
-+ pr_debug("[%s]: attempt to share resource %u\n", __func__,
-+ ioparam->handle);
-+
-+ shared_resource = vmcs_sm_acquire_global_resource(ioparam->handle);
-+ if (shared_resource == NULL) {
-+ ret = -ENOMEM;
-+ goto error;
-+ }
-+
-+ /* Allocate local resource to track this allocation.
-+ */
-+ resource = kzalloc(sizeof(*resource), GFP_KERNEL);
-+ if (resource == NULL) {
-+ pr_err("[%s]: failed to allocate local tracking resource\n",
-+ __func__);
-+ ret = -ENOMEM;
-+ goto error;
-+ }
-+ INIT_LIST_HEAD(&resource->map_list);
-+ resource->ref_count++;
-+ resource->pid = current->tgid;
-+
-+ /* Keep track of the resource we created.
-+ */
-+ resource->private = private;
-+ resource->res_handle = shared_resource->res_handle;
-+ resource->res_base_mem = shared_resource->res_base_mem;
-+ resource->res_size = shared_resource->res_size;
-+ resource->res_cached = shared_resource->res_cached;
-+ resource->res_shared = shared_resource;
-+
-+ mutex_lock(&sm_state->lock);
-+ resource->res_guid = ++sm_state->guid;
-+ mutex_unlock(&sm_state->lock);
-+ resource->res_guid <<= PAGE_SHIFT;
-+
-+ vmcs_sm_add_resource(private, resource);
-+
-+ pr_debug("[%s]: allocated data - guid %x, hdl %x, base address %p, size %d, cache %d\n",
-+ __func__, resource->res_guid, resource->res_handle,
-+ resource->res_base_mem, resource->res_size,
-+ resource->res_cached);
-+
-+ /* We're done */
-+ resource->res_stats[ALLOC]++;
-+ ioparam->handle = resource->res_guid;
-+ ioparam->size = resource->res_size;
-+ return 0;
-+
-+error:
-+ pr_err("[%s]: failed to share %u\n", __func__, ioparam->handle);
-+ if (shared_resource != NULL)
-+ vmcs_sm_release_resource(shared_resource, 0);
-+
-+ return ret;
-+}
-+
-+/* Free a previously allocated shared memory handle and block.
-+*/
-+static int vc_sm_ioctl_free(struct SM_PRIV_DATA_T *private,
-+ struct vmcs_sm_ioctl_free *ioparam)
-+{
-+ struct SM_RESOURCE_T *resource =
-+ vmcs_sm_acquire_resource(private, ioparam->handle);
-+
-+ if (resource == NULL) {
-+ pr_err("[%s]: resource for guid %u does not exist\n", __func__,
-+ ioparam->handle);
-+ return -EINVAL;
-+ }
-+
-+ /* Check permissions.
-+ */
-+ if (resource->pid && (resource->pid != current->tgid)) {
-+ pr_err("[%s]: current tgid %u != %u owner\n",
-+ __func__, current->tgid, resource->pid);
-+ vmcs_sm_release_resource(resource, 0);
-+ return -EPERM;
-+ }
-+
-+ vmcs_sm_release_resource(resource, 0);
-+ vmcs_sm_release_resource(resource, 0);
-+ return 0;
-+}
-+
-+/* Resize a previously allocated shared memory handle and block.
-+*/
-+static int vc_sm_ioctl_resize(struct SM_PRIV_DATA_T *private,
-+ struct vmcs_sm_ioctl_resize *ioparam)
-+{
-+ int ret = 0;
-+ int status;
-+ VC_SM_RESIZE_T resize;
-+ struct SM_RESOURCE_T *resource;
-+
-+ /* Locate resource from GUID.
-+ */
-+ resource = vmcs_sm_acquire_resource(private, ioparam->handle);
-+ if (!resource) {
-+ pr_err("[%s]: failed resource - guid %x\n",
-+ __func__, ioparam->handle);
-+ ret = -EFAULT;
-+ goto error;
-+ }
-+
-+ /* If the resource is locked, its reference count will be not NULL,
-+ ** in which case we will not be allowed to resize it anyways, so
-+ ** reject the attempt here.
-+ */
-+ if (resource->lock_count != 0) {
-+ pr_err("[%s]: cannot resize - guid %x, ref-cnt %d\n",
-+ __func__, ioparam->handle, resource->lock_count);
-+ ret = -EFAULT;
-+ goto error;
-+ }
-+
-+ /* Check permissions.
-+ */
-+ if (resource->pid && (resource->pid != current->tgid)) {
-+ pr_err("[%s]: current tgid %u != %u owner\n", __func__,
-+ current->tgid, resource->pid);
-+ ret = -EPERM;
-+ goto error;
-+ }
-+
-+ if (resource->map_count != 0) {
-+ pr_err("[%s]: cannot resize - guid %x, ref-cnt %d\n",
-+ __func__, ioparam->handle, resource->map_count);
-+ ret = -EFAULT;
-+ goto error;
-+ }
-+
-+ resize.res_handle = resource->res_handle;
-+ resize.res_mem = resource->res_base_mem;
-+ resize.res_new_size = ioparam->new_size;
-+
-+ pr_debug("[%s]: attempt to resize data - guid %x, hdl %x, base address %p\n",
-+ __func__, ioparam->handle, resize.res_handle, resize.res_mem);
-+
-+ /* Resize the videocore allocated resource.
-+ */
-+ status = vc_vchi_sm_resize(sm_state->sm_handle, &resize,
-+ &private->int_trans_id);
-+ if (status == -EINTR) {
-+ pr_debug("[%s]: requesting resize memory action restart (trans_id: %u)\n",
-+ __func__, private->int_trans_id);
-+ ret = -ERESTARTSYS;
-+ private->restart_sys = -EINTR;
-+ private->int_action = VC_SM_MSG_TYPE_RESIZE;
-+ goto error;
-+ } else if (status != 0) {
-+ pr_err("[%s]: failed to resize memory on videocore (status: %u, trans_id: %u)\n",
-+ __func__, status, private->int_trans_id);
-+ ret = -EPERM;
-+ goto error;
-+ }
-+
-+ pr_debug("[%s]: success to resize data - hdl %x, size %d -> %d\n",
-+ __func__, resize.res_handle, resource->res_size,
-+ resize.res_new_size);
-+
-+ /* Successfully resized, save the information and inform the user.
-+ */
-+ ioparam->old_size = resource->res_size;
-+ resource->res_size = resize.res_new_size;
-+
-+error:
-+ if (resource)
-+ vmcs_sm_release_resource(resource, 0);
-+
-+ return ret;
-+}
-+
-+/* Lock a previously allocated shared memory handle and block.
-+*/
-+static int vc_sm_ioctl_lock(struct SM_PRIV_DATA_T *private,
-+ struct vmcs_sm_ioctl_lock_unlock *ioparam,
-+ int change_cache, enum vmcs_sm_cache_e cache_type,
-+ unsigned int vc_addr)
-+{
-+ int status;
-+ VC_SM_LOCK_UNLOCK_T lock;
-+ VC_SM_LOCK_RESULT_T result;
-+ struct SM_RESOURCE_T *resource;
-+ int ret = 0;
-+ struct sm_mmap *map, *map_tmp;
-+ long unsigned int phys_addr;
-+
-+ map = NULL;
-+
-+ /* Locate resource from GUID.
-+ */
-+ resource = vmcs_sm_acquire_resource(private, ioparam->handle);
-+ if (resource == NULL) {
-+ ret = -EINVAL;
-+ goto error;
-+ }
-+
-+ /* Check permissions.
-+ */
-+ if (resource->pid && (resource->pid != current->tgid)) {
-+ pr_err("[%s]: current tgid %u != %u owner\n", __func__,
-+ current->tgid, resource->pid);
-+ ret = -EPERM;
-+ goto error;
-+ }
-+
-+ lock.res_handle = resource->res_handle;
-+ lock.res_mem = resource->res_base_mem;
-+
-+ /* Take the lock and get the address to be mapped.
-+ */
-+ if (vc_addr == 0) {
-+ pr_debug("[%s]: attempt to lock data - guid %x, hdl %x, base address %p\n",
-+ __func__, ioparam->handle, lock.res_handle,
-+ lock.res_mem);
-+
-+ /* Lock the videocore allocated resource.
-+ */
-+ status = vc_vchi_sm_lock(sm_state->sm_handle, &lock, &result,
-+ &private->int_trans_id);
-+ if (status == -EINTR) {
-+ pr_debug("[%s]: requesting lock memory action restart (trans_id: %u)\n",
-+ __func__, private->int_trans_id);
-+ ret = -ERESTARTSYS;
-+ private->restart_sys = -EINTR;
-+ private->int_action = VC_SM_MSG_TYPE_LOCK;
-+ goto error;
-+ } else if (status != 0 ||
-+ (status == 0 && result.res_mem == NULL)) {
-+ pr_err("[%s]: failed to lock memory on videocore (status: %u, trans_id: %u)\n",
-+ __func__, status, private->int_trans_id);
-+ ret = -EPERM;
-+ resource->res_stats[LOCK_FAIL]++;
-+ goto error;
-+ }
-+
-+ pr_debug("[%s]: succeed to lock data - hdl %x, base address %p (%p), ref-cnt %d\n",
-+ __func__, lock.res_handle, result.res_mem,
-+ lock.res_mem, resource->lock_count);
-+ }
-+ /* Lock assumed taken already, address to be mapped is known.
-+ */
-+ else
-+ resource->res_base_mem = (void *)vc_addr;
-+
-+ resource->res_stats[LOCK]++;
-+ resource->lock_count++;
-+
-+ /* Keep track of the new base memory allocation if it has changed.
-+ */
-+ if ((vc_addr == 0) &&
-+ (result.res_mem != NULL) &&
-+ (result.res_old_mem != NULL) &&
-+ (result.res_mem != result.res_old_mem)) {
-+ resource->res_base_mem = result.res_mem;
-+
-+ /* Kernel allocated resources.
-+ */
-+ if (resource->pid == 0) {
-+ if (!list_empty(&resource->map_list)) {
-+ list_for_each_entry_safe(map, map_tmp,
-+ &resource->map_list,
-+ resource_map_list) {
-+ if (map->res_addr) {
-+ iounmap((void *)map->res_addr);
-+ map->res_addr = 0;
-+
-+ vmcs_sm_remove_map(sm_state,
-+ map->resource,
-+ map);
-+ break;
-+ }
-+ }
-+ }
-+ }
-+ }
-+
-+ if (change_cache)
-+ resource->res_cached = cache_type;
-+
-+ if (resource->map_count) {
-+ ioparam->addr =
-+ vmcs_sm_usr_address_from_pid_and_usr_handle(
-+ current->tgid, ioparam->handle);
-+
-+ pr_debug("[%s] map_count %d private->pid %d current->tgid %d hnd %x addr %u\n",
-+ __func__, resource->map_count, private->pid,
-+ current->tgid, ioparam->handle, ioparam->addr);
-+ } else {
-+ /* Kernel allocated resources.
-+ */
-+ if (resource->pid == 0) {
-+ pr_debug("[%s]: attempt mapping kernel resource - guid %x, hdl %x\n",
-+ __func__, ioparam->handle, lock.res_handle);
-+
-+ ioparam->addr = 0;
-+
-+ map = kzalloc(sizeof(*map), GFP_KERNEL);
-+ if (map == NULL) {
-+ pr_err("[%s]: failed allocating tracker\n",
-+ __func__);
-+ ret = -ENOMEM;
-+ goto error;
-+ } else {
-+ phys_addr = (uint32_t)resource->res_base_mem &
-+ 0x3FFFFFFF;
-+ phys_addr += mm_vc_mem_phys_addr;
-+ if (resource->res_cached
-+ == VMCS_SM_CACHE_HOST) {
-+ ioparam->addr = (long unsigned int)
-+ /* TODO - make cached work */
-+ ioremap_nocache(phys_addr,
-+ resource->res_size);
-+
-+ pr_debug("[%s]: mapping kernel - guid %x, hdl %x - cached mapping %u\n",
-+ __func__, ioparam->handle,
-+ lock.res_handle, ioparam->addr);
-+ } else {
-+ ioparam->addr = (long unsigned int)
-+ ioremap_nocache(phys_addr,
-+ resource->res_size);
-+
-+ pr_debug("[%s]: mapping kernel- guid %x, hdl %x - non cached mapping %u\n",
-+ __func__, ioparam->handle,
-+ lock.res_handle, ioparam->addr);
-+ }
-+
-+ map->res_pid = 0;
-+ map->res_vc_hdl = resource->res_handle;
-+ map->res_usr_hdl = resource->res_guid;
-+ map->res_addr = ioparam->addr;
-+ map->resource = resource;
-+ map->vma = NULL;
-+
-+ vmcs_sm_add_map(sm_state, resource, map);
-+ }
-+ } else
-+ ioparam->addr = 0;
-+ }
-+
-+error:
-+ if (resource)
-+ vmcs_sm_release_resource(resource, 0);
-+
-+ return ret;
-+}
-+
-+/* Unlock a previously allocated shared memory handle and block.
-+*/
-+static int vc_sm_ioctl_unlock(struct SM_PRIV_DATA_T *private,
-+ struct vmcs_sm_ioctl_lock_unlock *ioparam,
-+ int flush, int wait_reply, int no_vc_unlock)
-+{
-+ int status;
-+ VC_SM_LOCK_UNLOCK_T unlock;
-+ struct sm_mmap *map, *map_tmp;
-+ struct SM_RESOURCE_T *resource;
-+ int ret = 0;
-+
-+ map = NULL;
-+
-+ /* Locate resource from GUID.
-+ */
-+ resource = vmcs_sm_acquire_resource(private, ioparam->handle);
-+ if (resource == NULL) {
-+ ret = -EINVAL;
-+ goto error;
-+ }
-+
-+ /* Check permissions.
-+ */
-+ if (resource->pid && (resource->pid != current->tgid)) {
-+ pr_err("[%s]: current tgid %u != %u owner\n",
-+ __func__, current->tgid, resource->pid);
-+ ret = -EPERM;
-+ goto error;
-+ }
-+
-+ unlock.res_handle = resource->res_handle;
-+ unlock.res_mem = resource->res_base_mem;
-+
-+ pr_debug("[%s]: attempt to unlock data - guid %x, hdl %x, base address %p\n",
-+ __func__, ioparam->handle, unlock.res_handle, unlock.res_mem);
-+
-+ /* User space allocated resources.
-+ */
-+ if (resource->pid) {
-+ /* Flush if requested */
-+ if (resource->res_cached && flush) {
-+ dma_addr_t phys_addr = 0;
-+ resource->res_stats[FLUSH]++;
-+
-+ phys_addr =
-+ (dma_addr_t)((uint32_t)resource->res_base_mem &
-+ 0x3FFFFFFF);
-+ phys_addr += (dma_addr_t)mm_vc_mem_phys_addr;
-+
-+ /* L1 cache flush */
-+ down_read(¤t->mm->mmap_sem);
-+ list_for_each_entry(map, &resource->map_list,
-+ resource_map_list) {
-+ if (map->vma) {
-+ unsigned long start;
-+ unsigned long end;
-+ start = map->vma->vm_start;
-+ end = map->vma->vm_end;
-+
-+ vcsm_vma_cache_clean_page_range(
-+ start, end);
-+ }
-+ }
-+ up_read(¤t->mm->mmap_sem);
-+
-+ /* L2 cache flush */
-+ outer_clean_range(phys_addr,
-+ phys_addr +
-+ (size_t) resource->res_size);
-+ }
-+
-+ /* We need to zap all the vmas associated with this resource */
-+ if (resource->lock_count == 1) {
-+ down_read(¤t->mm->mmap_sem);
-+ list_for_each_entry(map, &resource->map_list,
-+ resource_map_list) {
-+ if (map->vma) {
-+ zap_vma_ptes(map->vma,
-+ map->vma->vm_start,
-+ map->vma->vm_end -
-+ map->vma->vm_start);
-+ }
-+ }
-+ up_read(¤t->mm->mmap_sem);
-+ }
-+ }
-+ /* Kernel allocated resources. */
-+ else {
-+ /* Global + Taken in this context */
-+ if (resource->ref_count == 2) {
-+ if (!list_empty(&resource->map_list)) {
-+ list_for_each_entry_safe(map, map_tmp,
-+ &resource->map_list,
-+ resource_map_list) {
-+ if (map->res_addr) {
-+ if (flush &&
-+ (resource->res_cached ==
-+ VMCS_SM_CACHE_HOST)) {
-+ long unsigned int
-+ phys_addr;
-+ phys_addr = (uint32_t)
-+ resource->res_base_mem & 0x3FFFFFFF;
-+ phys_addr +=
-+ mm_vc_mem_phys_addr;
-+
-+ /* L1 cache flush */
-+ dmac_flush_range((const
-+ void
-+ *)
-+ map->res_addr, (const void *)
-+ (map->res_addr + resource->res_size));
-+
-+ /* L2 cache flush */
-+ outer_clean_range
-+ (phys_addr,
-+ phys_addr +
-+ (size_t)
-+ resource->res_size);
-+ }
-+
-+ iounmap((void *)map->res_addr);
-+ map->res_addr = 0;
-+
-+ vmcs_sm_remove_map(sm_state,
-+ map->resource,
-+ map);
-+ break;
-+ }
-+ }
-+ }
-+ }
-+ }
-+
-+ if (resource->lock_count) {
-+ /* Bypass the videocore unlock.
-+ */
-+ if (no_vc_unlock)
-+ status = 0;
-+ /* Unlock the videocore allocated resource.
-+ */
-+ else {
-+ status =
-+ vc_vchi_sm_unlock(sm_state->sm_handle, &unlock,
-+ &private->int_trans_id,
-+ wait_reply);
-+ if (status == -EINTR) {
-+ pr_debug("[%s]: requesting unlock memory action restart (trans_id: %u)\n",
-+ __func__, private->int_trans_id);
-+
-+ ret = -ERESTARTSYS;
-+ resource->res_stats[UNLOCK]--;
-+ private->restart_sys = -EINTR;
-+ private->int_action = VC_SM_MSG_TYPE_UNLOCK;
-+ goto error;
-+ } else if (status != 0) {
-+ pr_err("[%s]: failed to unlock vc mem (status: %u, trans_id: %u)\n",
-+ __func__, status, private->int_trans_id);
-+
-+ ret = -EPERM;
-+ resource->res_stats[UNLOCK_FAIL]++;
-+ goto error;
-+ }
-+ }
-+
-+ resource->res_stats[UNLOCK]++;
-+ resource->lock_count--;
-+ }
-+
-+ pr_debug("[%s]: success to unlock data - hdl %x, base address %p, ref-cnt %d\n",
-+ __func__, unlock.res_handle, unlock.res_mem,
-+ resource->lock_count);
-+
-+error:
-+ if (resource)
-+ vmcs_sm_release_resource(resource, 0);
-+
-+ return ret;
-+}
-+
-+/* Handle control from host. */
-+static long vc_sm_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
-+{
-+ int ret = 0;
-+ unsigned int cmdnr = _IOC_NR(cmd);
-+ struct SM_PRIV_DATA_T *file_data =
-+ (struct SM_PRIV_DATA_T *)file->private_data;
-+ struct SM_RESOURCE_T *resource = NULL;
-+
-+ /* Validate we can work with this device. */
-+ if ((sm_state == NULL) || (file_data == NULL)) {
-+ pr_err("[%s]: invalid device\n", __func__);
-+ ret = -EPERM;
-+ goto out;
-+ }
-+
-+ pr_debug("[%s]: cmd %x tgid %u, owner %u\n", __func__, cmdnr,
-+ current->tgid, file_data->pid);
-+
-+ /* Action is a re-post of a previously interrupted action? */
-+ if (file_data->restart_sys == -EINTR) {
-+ VC_SM_ACTION_CLEAN_T action_clean;
-+
-+ pr_debug("[%s]: clean up of action %u (trans_id: %u) following EINTR\n",
-+ __func__, file_data->int_action,
-+ file_data->int_trans_id);
-+
-+ action_clean.res_action = file_data->int_action;
-+ action_clean.action_trans_id = file_data->int_trans_id;
-+
-+ vc_vchi_sm_clean_up(sm_state->sm_handle, &action_clean);
-+
-+ file_data->restart_sys = 0;
-+ }
-+
-+ /* Now process the command.
-+ */
-+ switch (cmdnr) {
-+ /* New memory allocation.
-+ */
-+ case VMCS_SM_CMD_ALLOC:
-+ {
-+ struct vmcs_sm_ioctl_alloc ioparam;
-+
-+ /* Get the parameter data.
-+ */
-+ if (copy_from_user
-+ (&ioparam, (void *)arg, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-from-user for cmd %x\n",
-+ __func__, cmdnr);
-+ ret = -EFAULT;
-+ goto out;
-+ }
-+
-+ ret = vc_sm_ioctl_alloc(file_data, &ioparam);
-+ if (!ret &&
-+ (copy_to_user((void *)arg,
-+ &ioparam, sizeof(ioparam)) != 0)) {
-+ struct vmcs_sm_ioctl_free freeparam = {
-+ ioparam.handle
-+ };
-+ pr_err("[%s]: failed to copy-to-user for cmd %x\n",
-+ __func__, cmdnr);
-+ vc_sm_ioctl_free(file_data, &freeparam);
-+ ret = -EFAULT;
-+ }
-+
-+ /* Done.
-+ */
-+ goto out;
-+ }
-+ break;
-+
-+ /* Share existing memory allocation.
-+ */
-+ case VMCS_SM_CMD_ALLOC_SHARE:
-+ {
-+ struct vmcs_sm_ioctl_alloc_share ioparam;
-+
-+ /* Get the parameter data.
-+ */
-+ if (copy_from_user
-+ (&ioparam, (void *)arg, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-from-user for cmd %x\n",
-+ __func__, cmdnr);
-+ ret = -EFAULT;
-+ goto out;
-+ }
-+
-+ ret = vc_sm_ioctl_alloc_share(file_data, &ioparam);
-+
-+ /* Copy result back to user.
-+ */
-+ if (!ret
-+ && copy_to_user((void *)arg, &ioparam,
-+ sizeof(ioparam)) != 0) {
-+ struct vmcs_sm_ioctl_free freeparam = {
-+ ioparam.handle
-+ };
-+ pr_err("[%s]: failed to copy-to-user for cmd %x\n",
-+ __func__, cmdnr);
-+ vc_sm_ioctl_free(file_data, &freeparam);
-+ ret = -EFAULT;
-+ }
-+
-+ /* Done.
-+ */
-+ goto out;
-+ }
-+ break;
-+
-+ /* Lock (attempt to) *and* register a cache behavior change.
-+ */
-+ case VMCS_SM_CMD_LOCK_CACHE:
-+ {
-+ struct vmcs_sm_ioctl_lock_cache ioparam;
-+ struct vmcs_sm_ioctl_lock_unlock lock;
-+
-+ /* Get parameter data.
-+ */
-+ if (copy_from_user
-+ (&ioparam, (void *)arg, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-from-user for cmd %x\n",
-+ __func__, cmdnr);
-+ ret = -EFAULT;
-+ goto out;
-+ }
-+
-+ lock.handle = ioparam.handle;
-+ ret =
-+ vc_sm_ioctl_lock(file_data, &lock, 1,
-+ ioparam.cached, 0);
-+
-+ /* Done.
-+ */
-+ goto out;
-+ }
-+ break;
-+
-+ /* Lock (attempt to) existing memory allocation.
-+ */
-+ case VMCS_SM_CMD_LOCK:
-+ {
-+ struct vmcs_sm_ioctl_lock_unlock ioparam;
-+
-+ /* Get parameter data.
-+ */
-+ if (copy_from_user
-+ (&ioparam, (void *)arg, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-from-user for cmd %x\n",
-+ __func__, cmdnr);
-+ ret = -EFAULT;
-+ goto out;
-+ }
-+
-+ ret = vc_sm_ioctl_lock(file_data, &ioparam, 0, 0, 0);
-+
-+ /* Copy result back to user.
-+ */
-+ if (copy_to_user((void *)arg, &ioparam, sizeof(ioparam))
-+ != 0) {
-+ pr_err("[%s]: failed to copy-to-user for cmd %x\n",
-+ __func__, cmdnr);
-+ ret = -EFAULT;
-+ }
-+
-+ /* Done.
-+ */
-+ goto out;
-+ }
-+ break;
-+
-+ /* Unlock (attempt to) existing memory allocation.
-+ */
-+ case VMCS_SM_CMD_UNLOCK:
-+ {
-+ struct vmcs_sm_ioctl_lock_unlock ioparam;
-+
-+ /* Get parameter data.
-+ */
-+ if (copy_from_user
-+ (&ioparam, (void *)arg, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-from-user for cmd %x\n",
-+ __func__, cmdnr);
-+ ret = -EFAULT;
-+ goto out;
-+ }
-+
-+ ret = vc_sm_ioctl_unlock(file_data, &ioparam, 0, 1, 0);
-+
-+ /* Done.
-+ */
-+ goto out;
-+ }
-+ break;
-+
-+ /* Resize (attempt to) existing memory allocation.
-+ */
-+ case VMCS_SM_CMD_RESIZE:
-+ {
-+ struct vmcs_sm_ioctl_resize ioparam;
-+
-+ /* Get parameter data.
-+ */
-+ if (copy_from_user
-+ (&ioparam, (void *)arg, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-from-user for cmd %x\n",
-+ __func__, cmdnr);
-+ ret = -EFAULT;
-+ goto out;
-+ }
-+
-+ ret = vc_sm_ioctl_resize(file_data, &ioparam);
-+
-+ /* Copy result back to user.
-+ */
-+ if (copy_to_user((void *)arg, &ioparam, sizeof(ioparam))
-+ != 0) {
-+ pr_err("[%s]: failed to copy-to-user for cmd %x\n",
-+ __func__, cmdnr);
-+ ret = -EFAULT;
-+ }
-+
-+ /* Done.
-+ */
-+ goto out;
-+ }
-+ break;
-+
-+ /* Terminate existing memory allocation.
-+ */
-+ case VMCS_SM_CMD_FREE:
-+ {
-+ struct vmcs_sm_ioctl_free ioparam;
-+
-+ /* Get parameter data.
-+ */
-+ if (copy_from_user
-+ (&ioparam, (void *)arg, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-from-user for cmd %x\n",
-+ __func__, cmdnr);
-+ ret = -EFAULT;
-+ goto out;
-+ }
-+
-+ ret = vc_sm_ioctl_free(file_data, &ioparam);
-+
-+ /* Done.
-+ */
-+ goto out;
-+ }
-+ break;
-+
-+ /* Walk allocation on videocore, information shows up in the
-+ ** videocore log.
-+ */
-+ case VMCS_SM_CMD_VC_WALK_ALLOC:
-+ {
-+ pr_debug("[%s]: invoking walk alloc\n", __func__);
-+
-+ if (vc_vchi_sm_walk_alloc(sm_state->sm_handle) != 0)
-+ pr_err("[%s]: failed to walk-alloc on videocore\n",
-+ __func__);
-+
-+ /* Done.
-+ */
-+ goto out;
-+ }
-+ break;
-+/* Walk mapping table on host, information shows up in the
-+ ** kernel log.
-+ */
-+ case VMCS_SM_CMD_HOST_WALK_MAP:
-+ {
-+ /* Use pid of -1 to tell to walk the whole map. */
-+ vmcs_sm_host_walk_map_per_pid(-1);
-+
-+ /* Done. */
-+ goto out;
-+ }
-+ break;
-+
-+ /* Walk mapping table per process on host. */
-+ case VMCS_SM_CMD_HOST_WALK_PID_ALLOC:
-+ {
-+ struct vmcs_sm_ioctl_walk ioparam;
-+
-+ /* Get parameter data. */
-+ if (copy_from_user(&ioparam,
-+ (void *)arg, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-from-user for cmd %x\n",
-+ __func__, cmdnr);
-+ ret = -EFAULT;
-+ goto out;
-+ }
-+
-+ vmcs_sm_host_walk_alloc(file_data);
-+
-+ /* Done. */
-+ goto out;
-+ }
-+ break;
-+
-+ /* Walk allocation per process on host. */
-+ case VMCS_SM_CMD_HOST_WALK_PID_MAP:
-+ {
-+ struct vmcs_sm_ioctl_walk ioparam;
-+
-+ /* Get parameter data. */
-+ if (copy_from_user(&ioparam,
-+ (void *)arg, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-from-user for cmd %x\n",
-+ __func__, cmdnr);
-+ ret = -EFAULT;
-+ goto out;
-+ }
-+
-+ vmcs_sm_host_walk_map_per_pid(ioparam.pid);
-+
-+ /* Done. */
-+ goto out;
-+ }
-+ break;
-+
-+ /* Gets the size of the memory associated with a user handle. */
-+ case VMCS_SM_CMD_SIZE_USR_HANDLE:
-+ {
-+ struct vmcs_sm_ioctl_size ioparam;
-+
-+ /* Get parameter data. */
-+ if (copy_from_user(&ioparam,
-+ (void *)arg, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-from-user for cmd %x\n",
-+ __func__, cmdnr);
-+ ret = -EFAULT;
-+ goto out;
-+ }
-+
-+ /* Locate resource from GUID. */
-+ resource =
-+ vmcs_sm_acquire_resource(file_data, ioparam.handle);
-+ if (resource != NULL) {
-+ ioparam.size = resource->res_size;
-+ vmcs_sm_release_resource(resource, 0);
-+ } else {
-+ ioparam.size = 0;
-+ }
-+
-+ if (copy_to_user((void *)arg,
-+ &ioparam, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-to-user for cmd %x\n",
-+ __func__, cmdnr);
-+ ret = -EFAULT;
-+ }
-+
-+ /* Done. */
-+ goto out;
-+ }
-+ break;
-+
-+ /* Verify we are dealing with a valid resource. */
-+ case VMCS_SM_CMD_CHK_USR_HANDLE:
-+ {
-+ struct vmcs_sm_ioctl_chk ioparam;
-+
-+ /* Get parameter data.
-+ */
-+ if (copy_from_user(&ioparam,
-+ (void *)arg, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-from-user for cmd %x\n",
-+ __func__, cmdnr);
-+
-+ ret = -EFAULT;
-+ goto out;
-+ }
-+
-+ /* Locate resource from GUID. */
-+ resource =
-+ vmcs_sm_acquire_resource(file_data, ioparam.handle);
-+ if (resource == NULL)
-+ ret = -EINVAL;
-+ /* If the resource is cacheable, return additional
-+ * information that may be needed to flush the cache.
-+ */
-+ else if ((resource->res_cached == VMCS_SM_CACHE_HOST) ||
-+ (resource->res_cached == VMCS_SM_CACHE_BOTH)) {
-+ ioparam.addr =
-+ vmcs_sm_usr_address_from_pid_and_usr_handle
-+ (current->tgid, ioparam.handle);
-+ ioparam.size = resource->res_size;
-+ ioparam.cache = resource->res_cached;
-+ } else {
-+ ioparam.addr = 0;
-+ ioparam.size = 0;
-+ ioparam.cache = resource->res_cached;
-+ }
-+
-+ if (resource)
-+ vmcs_sm_release_resource(resource, 0);
-+
-+ if (copy_to_user((void *)arg,
-+ &ioparam, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-to-user for cmd %x\n",
-+ __func__, cmdnr);
-+ ret = -EFAULT;
-+ }
-+
-+ /* Done.
-+ */
-+ goto out;
-+ }
-+ break;
-+
-+ /*
-+ * Maps a user handle given the process and the virtual address.
-+ */
-+ case VMCS_SM_CMD_MAPPED_USR_HANDLE:
-+ {
-+ struct vmcs_sm_ioctl_map ioparam;
-+
-+ /* Get parameter data. */
-+ if (copy_from_user(&ioparam,
-+ (void *)arg, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-from-user for cmd %x\n",
-+ __func__, cmdnr);
-+
-+ ret = -EFAULT;
-+ goto out;
-+ }
-+
-+ ioparam.handle =
-+ vmcs_sm_usr_handle_from_pid_and_address(
-+ ioparam.pid, ioparam.addr);
-+
-+ resource =
-+ vmcs_sm_acquire_resource(file_data, ioparam.handle);
-+ if ((resource != NULL)
-+ && ((resource->res_cached == VMCS_SM_CACHE_HOST)
-+ || (resource->res_cached ==
-+ VMCS_SM_CACHE_BOTH))) {
-+ ioparam.size = resource->res_size;
-+ } else {
-+ ioparam.size = 0;
-+ }
-+
-+ if (resource)
-+ vmcs_sm_release_resource(resource, 0);
-+
-+ if (copy_to_user((void *)arg,
-+ &ioparam, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-to-user for cmd %x\n",
-+ __func__, cmdnr);
-+ ret = -EFAULT;
-+ }
-+
-+ /* Done. */
-+ goto out;
-+ }
-+ break;
-+
-+ /*
-+ * Maps a videocore handle given process and virtual address.
-+ */
-+ case VMCS_SM_CMD_MAPPED_VC_HDL_FROM_ADDR:
-+ {
-+ struct vmcs_sm_ioctl_map ioparam;
-+
-+ /* Get parameter data. */
-+ if (copy_from_user(&ioparam,
-+ (void *)arg, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-from-user for cmd %x\n",
-+ __func__, cmdnr);
-+ ret = -EFAULT;
-+ goto out;
-+ }
-+
-+ ioparam.handle = vmcs_sm_vc_handle_from_pid_and_address(
-+ ioparam.pid, ioparam.addr);
-+
-+ if (copy_to_user((void *)arg,
-+ &ioparam, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-to-user for cmd %x\n",
-+ __func__, cmdnr);
-+
-+ ret = -EFAULT;
-+ }
-+
-+ /* Done.
-+ */
-+ goto out;
-+ }
-+ break;
-+
-+ /* Maps a videocore handle given process and user handle. */
-+ case VMCS_SM_CMD_MAPPED_VC_HDL_FROM_HDL:
-+ {
-+ struct vmcs_sm_ioctl_map ioparam;
-+
-+ /* Get parameter data. */
-+ if (copy_from_user(&ioparam,
-+ (void *)arg, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-from-user for cmd %x\n",
-+ __func__, cmdnr);
-+ ret = -EFAULT;
-+ goto out;
-+ }
-+
-+ /* Locate resource from GUID. */
-+ resource =
-+ vmcs_sm_acquire_resource(file_data, ioparam.handle);
-+ if (resource != NULL) {
-+ ioparam.handle = resource->res_handle;
-+ vmcs_sm_release_resource(resource, 0);
-+ } else {
-+ ioparam.handle = 0;
-+ }
-+
-+ if (copy_to_user((void *)arg,
-+ &ioparam, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-to-user for cmd %x\n",
-+ __func__, cmdnr);
-+
-+ ret = -EFAULT;
-+ }
-+
-+ /* Done. */
-+ goto out;
-+ }
-+ break;
-+
-+ /*
-+ * Maps a videocore address given process and videocore handle.
-+ */
-+ case VMCS_SM_CMD_MAPPED_VC_ADDR_FROM_HDL:
-+ {
-+ struct vmcs_sm_ioctl_map ioparam;
-+
-+ /* Get parameter data. */
-+ if (copy_from_user(&ioparam,
-+ (void *)arg, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-from-user for cmd %x\n",
-+ __func__, cmdnr);
-+
-+ ret = -EFAULT;
-+ goto out;
-+ }
-+
-+ /* Locate resource from GUID. */
-+ resource =
-+ vmcs_sm_acquire_resource(file_data, ioparam.handle);
-+ if (resource != NULL) {
-+ ioparam.addr =
-+ (unsigned int)resource->res_base_mem;
-+ vmcs_sm_release_resource(resource, 0);
-+ } else {
-+ ioparam.addr = 0;
-+ }
-+
-+ if (copy_to_user((void *)arg,
-+ &ioparam, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-to-user for cmd %x\n",
-+ __func__, cmdnr);
-+ ret = -EFAULT;
-+ }
-+
-+ /* Done. */
-+ goto out;
-+ }
-+ break;
-+
-+ /* Maps a user address given process and vc handle.
-+ */
-+ case VMCS_SM_CMD_MAPPED_USR_ADDRESS:
-+ {
-+ struct vmcs_sm_ioctl_map ioparam;
-+
-+ /* Get parameter data. */
-+ if (copy_from_user(&ioparam,
-+ (void *)arg, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-from-user for cmd %x\n",
-+ __func__, cmdnr);
-+ ret = -EFAULT;
-+ goto out;
-+ }
-+
-+ /*
-+ * Return the address information from the mapping,
-+ * 0 (ie NULL) if it cannot locate the actual mapping.
-+ */
-+ ioparam.addr =
-+ vmcs_sm_usr_address_from_pid_and_usr_handle
-+ (ioparam.pid, ioparam.handle);
-+
-+ if (copy_to_user((void *)arg,
-+ &ioparam, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-to-user for cmd %x\n",
-+ __func__, cmdnr);
-+ ret = -EFAULT;
-+ }
-+
-+ /* Done. */
-+ goto out;
-+ }
-+ break;
-+
-+ /* Flush the cache for a given mapping. */
-+ case VMCS_SM_CMD_FLUSH:
-+ {
-+ struct vmcs_sm_ioctl_cache ioparam;
-+
-+ /* Get parameter data. */
-+ if (copy_from_user(&ioparam,
-+ (void *)arg, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-from-user for cmd %x\n",
-+ __func__, cmdnr);
-+ ret = -EFAULT;
-+ goto out;
-+ }
-+
-+ /* Locate resource from GUID. */
-+ resource =
-+ vmcs_sm_acquire_resource(file_data, ioparam.handle);
-+
-+ if ((resource != NULL) && resource->res_cached) {
-+ dma_addr_t phys_addr = 0;
-+
-+ resource->res_stats[FLUSH]++;
-+
-+ phys_addr =
-+ (dma_addr_t)((uint32_t)
-+ resource->res_base_mem &
-+ 0x3FFFFFFF);
-+ phys_addr += (dma_addr_t)mm_vc_mem_phys_addr;
-+
-+ /* L1 cache flush */
-+ down_read(¤t->mm->mmap_sem);
-+ vcsm_vma_cache_clean_page_range((unsigned long)
-+ ioparam.addr,
-+ (unsigned long)
-+ ioparam.addr +
-+ ioparam.size);
-+ up_read(¤t->mm->mmap_sem);
-+
-+ /* L2 cache flush */
-+ outer_clean_range(phys_addr,
-+ phys_addr +
-+ (size_t) ioparam.size);
-+ } else if (resource == NULL) {
-+ ret = -EINVAL;
-+ goto out;
-+ }
-+
-+ if (resource)
-+ vmcs_sm_release_resource(resource, 0);
-+
-+ /* Done. */
-+ goto out;
-+ }
-+ break;
-+
-+ /* Invalidate the cache for a given mapping. */
-+ case VMCS_SM_CMD_INVALID:
-+ {
-+ struct vmcs_sm_ioctl_cache ioparam;
-+
-+ /* Get parameter data. */
-+ if (copy_from_user(&ioparam,
-+ (void *)arg, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-from-user for cmd %x\n",
-+ __func__, cmdnr);
-+ ret = -EFAULT;
-+ goto out;
-+ }
-+
-+ /* Locate resource from GUID.
-+ */
-+ resource =
-+ vmcs_sm_acquire_resource(file_data, ioparam.handle);
-+
-+ if ((resource != NULL) && resource->res_cached) {
-+ dma_addr_t phys_addr = 0;
-+
-+ resource->res_stats[INVALID]++;
-+
-+ phys_addr =
-+ (dma_addr_t)((uint32_t)
-+ resource->res_base_mem &
-+ 0x3FFFFFFF);
-+ phys_addr += (dma_addr_t)mm_vc_mem_phys_addr;
-+
-+ /* L2 cache invalidate */
-+ outer_inv_range(phys_addr,
-+ phys_addr +
-+ (size_t) ioparam.size);
-+
-+ /* L1 cache invalidate */
-+ down_read(¤t->mm->mmap_sem);
-+ vcsm_vma_cache_clean_page_range((unsigned long)
-+ ioparam.addr,
-+ (unsigned long)
-+ ioparam.addr +
-+ ioparam.size);
-+ up_read(¤t->mm->mmap_sem);
-+ } else if (resource == NULL) {
-+ ret = -EINVAL;
-+ goto out;
-+ }
-+
-+ if (resource)
-+ vmcs_sm_release_resource(resource, 0);
-+
-+ /* Done.
-+ */
-+ goto out;
-+ }
-+ break;
-+
-+ /* Flush/Invalidate the cache for a given mapping. */
-+ case VMCS_SM_CMD_CLEAN_INVALID:
-+ {
-+ int i;
-+ struct vmcs_sm_ioctl_clean_invalid ioparam;
-+
-+ /* Get parameter data. */
-+ if (copy_from_user(&ioparam,
-+ (void *)arg, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-from-user for cmd %x\n",
-+ __func__, cmdnr);
-+ ret = -EFAULT;
-+ goto out;
-+ }
-+ for (i=0; i<sizeof ioparam.s/sizeof *ioparam.s; i++) {
-+ switch (ioparam.s[i].cmd) {
-+ default: case 0: break; /* NOOP */
-+ case 1: /* L1/L2 invalidate virtual range */
-+ case 2: /* L1/L2 clean physical range */
-+ case 3: /* L1/L2 clean+invalidate all */
-+ {
-+ /* Locate resource from GUID.
-+ */
-+ resource =
-+ vmcs_sm_acquire_resource(file_data, ioparam.s[i].handle);
-+
-+ if ((resource != NULL) && resource->res_cached) {
-+ unsigned long base = ioparam.s[i].addr & ~(PAGE_SIZE-1);
-+ unsigned long end = (ioparam.s[i].addr + ioparam.s[i].size + PAGE_SIZE-1) & ~(PAGE_SIZE-1);
-+ resource->res_stats[ioparam.s[i].cmd == 1 ? INVALID:FLUSH]++;
-+
-+ /* L1/L2 cache flush */
-+ down_read(¤t->mm->mmap_sem);
-+ vcsm_vma_cache_clean_page_range(base, end);
-+ up_read(¤t->mm->mmap_sem);
-+ } else if (resource == NULL) {
-+ ret = -EINVAL;
-+ goto out;
-+ }
-+
-+ if (resource)
-+ vmcs_sm_release_resource(resource, 0);
-+ }
-+ break;
-+ }
-+ }
-+ }
-+ break;
-+
-+ default:
-+ {
-+ ret = -EINVAL;
-+ goto out;
-+ }
-+ break;
-+ }
-+
-+out:
-+ return ret;
-+}
-+
-+/* Device operations that we managed in this driver.
-+*/
-+static const struct file_operations vmcs_sm_ops = {
-+ .owner = THIS_MODULE,
-+ .unlocked_ioctl = vc_sm_ioctl,
-+ .open = vc_sm_open,
-+ .release = vc_sm_release,
-+ .mmap = vc_sm_mmap,
-+};
-+
-+/* Creation of device.
-+*/
-+static int vc_sm_create_sharedmemory(void)
-+{
-+ int ret;
-+
-+ if (sm_state == NULL) {
-+ ret = -ENOMEM;
-+ goto out;
-+ }
-+
-+ /* Create a device class for creating dev nodes.
-+ */
-+ sm_state->sm_class = class_create(THIS_MODULE, "vc-sm");
-+ if (IS_ERR(sm_state->sm_class)) {
-+ pr_err("[%s]: unable to create device class\n", __func__);
-+ ret = PTR_ERR(sm_state->sm_class);
-+ goto out;
-+ }
-+
-+ /* Create a character driver.
-+ */
-+ ret = alloc_chrdev_region(&sm_state->sm_devid,
-+ DEVICE_MINOR, 1, DEVICE_NAME);
-+ if (ret != 0) {
-+ pr_err("[%s]: unable to allocate device number\n", __func__);
-+ goto out_dev_class_destroy;
-+ }
-+
-+ cdev_init(&sm_state->sm_cdev, &vmcs_sm_ops);
-+ ret = cdev_add(&sm_state->sm_cdev, sm_state->sm_devid, 1);
-+ if (ret != 0) {
-+ pr_err("[%s]: unable to register device\n", __func__);
-+ goto out_chrdev_unreg;
-+ }
-+
-+ /* Create a device node.
-+ */
-+ sm_state->sm_dev = device_create(sm_state->sm_class,
-+ NULL,
-+ MKDEV(MAJOR(sm_state->sm_devid),
-+ DEVICE_MINOR), NULL,
-+ DEVICE_NAME);
-+ if (IS_ERR(sm_state->sm_dev)) {
-+ pr_err("[%s]: unable to create device node\n", __func__);
-+ ret = PTR_ERR(sm_state->sm_dev);
-+ goto out_chrdev_del;
-+ }
-+
-+ goto out;
-+
-+out_chrdev_del:
-+ cdev_del(&sm_state->sm_cdev);
-+out_chrdev_unreg:
-+ unregister_chrdev_region(sm_state->sm_devid, 1);
-+out_dev_class_destroy:
-+ class_destroy(sm_state->sm_class);
-+ sm_state->sm_class = NULL;
-+out:
-+ return ret;
-+}
-+
-+/* Termination of the device.
-+*/
-+static int vc_sm_remove_sharedmemory(void)
-+{
-+ int ret;
-+
-+ if (sm_state == NULL) {
-+ /* Nothing to do.
-+ */
-+ ret = 0;
-+ goto out;
-+ }
-+
-+ /* Remove the sharedmemory character driver.
-+ */
-+ cdev_del(&sm_state->sm_cdev);
-+
-+ /* Unregister region.
-+ */
-+ unregister_chrdev_region(sm_state->sm_devid, 1);
-+
-+ ret = 0;
-+ goto out;
-+
-+out:
-+ return ret;
-+}
-+
-+/* Videocore connected. */
-+static void vc_sm_connected_init(void)
-+{
-+ int ret;
-+ VCHI_INSTANCE_T vchi_instance;
-+ VCHI_CONNECTION_T *vchi_connection = NULL;
-+
-+ pr_info("[%s]: start\n", __func__);
-+
-+ /* Allocate memory for the state structure.
-+ */
-+ sm_state = kzalloc(sizeof(struct SM_STATE_T), GFP_KERNEL);
-+ if (sm_state == NULL) {
-+ pr_err("[%s]: failed to allocate memory\n", __func__);
-+ ret = -ENOMEM;
-+ goto out;
-+ }
-+
-+ mutex_init(&sm_state->lock);
-+ mutex_init(&sm_state->map_lock);
-+
-+ /* Initialize and create a VCHI connection for the shared memory service
-+ ** running on videocore.
-+ */
-+ ret = vchi_initialise(&vchi_instance);
-+ if (ret != 0) {
-+ pr_err("[%s]: failed to initialise VCHI instance (ret=%d)\n",
-+ __func__, ret);
-+
-+ ret = -EIO;
-+ goto err_free_mem;
-+ }
-+
-+ ret = vchi_connect(NULL, 0, vchi_instance);
-+ if (ret != 0) {
-+ pr_err("[%s]: failed to connect VCHI instance (ret=%d)\n",
-+ __func__, ret);
-+
-+ ret = -EIO;
-+ goto err_free_mem;
-+ }
-+
-+ /* Initialize an instance of the shared memory service. */
-+ sm_state->sm_handle =
-+ vc_vchi_sm_init(vchi_instance, &vchi_connection, 1);
-+ if (sm_state->sm_handle == NULL) {
-+ pr_err("[%s]: failed to initialize shared memory service\n",
-+ __func__);
-+
-+ ret = -EPERM;
-+ goto err_free_mem;
-+ }
-+
-+ /* Create a debug fs directory entry (root). */
-+ sm_state->dir_root = debugfs_create_dir(VC_SM_DIR_ROOT_NAME, NULL);
-+ if (!sm_state->dir_root) {
-+ pr_err("[%s]: failed to create \'%s\' directory entry\n",
-+ __func__, VC_SM_DIR_ROOT_NAME);
-+
-+ ret = -EPERM;
-+ goto err_stop_sm_service;
-+ }
-+
-+ sm_state->dir_state.show = &vc_sm_global_state_show;
-+ sm_state->dir_state.dir_entry = debugfs_create_file(VC_SM_STATE,
-+ S_IRUGO, sm_state->dir_root, &sm_state->dir_state,
-+ &vc_sm_debug_fs_fops);
-+
-+ sm_state->dir_stats.show = &vc_sm_global_statistics_show;
-+ sm_state->dir_stats.dir_entry = debugfs_create_file(VC_SM_STATS,
-+ S_IRUGO, sm_state->dir_root, &sm_state->dir_stats,
-+ &vc_sm_debug_fs_fops);
-+
-+ /* Create the proc entry children. */
-+ sm_state->dir_alloc = debugfs_create_dir(VC_SM_DIR_ALLOC_NAME,
-+ sm_state->dir_root);
-+
-+ /* Create a shared memory device. */
-+ ret = vc_sm_create_sharedmemory();
-+ if (ret != 0) {
-+ pr_err("[%s]: failed to create shared memory device\n",
-+ __func__);
-+ goto err_remove_debugfs;
-+ }
-+
-+ INIT_LIST_HEAD(&sm_state->map_list);
-+ INIT_LIST_HEAD(&sm_state->resource_list);
-+
-+ sm_state->data_knl = vc_sm_create_priv_data(0);
-+ if (sm_state->data_knl == NULL) {
-+ pr_err("[%s]: failed to create kernel private data tracker\n",
-+ __func__);
-+ goto err_remove_shared_memory;
-+ }
-+
-+ /* Done!
-+ */
-+ sm_inited = 1;
-+ goto out;
-+
-+err_remove_shared_memory:
-+ vc_sm_remove_sharedmemory();
-+err_remove_debugfs:
-+ debugfs_remove_recursive(sm_state->dir_root);
-+err_stop_sm_service:
-+ vc_vchi_sm_stop(&sm_state->sm_handle);
-+err_free_mem:
-+ kfree(sm_state);
-+out:
-+ pr_info("[%s]: end - returning %d\n", __func__, ret);
-+}
-+
-+/* Driver loading. */
-+static int __init vc_sm_init(void)
-+{
-+ pr_info("vc-sm: Videocore shared memory driver\n");
-+ vchiq_add_connected_callback(vc_sm_connected_init);
-+ return 0;
-+}
-+
-+/* Driver unloading. */
-+static void __exit vc_sm_exit(void)
-+{
-+ pr_debug("[%s]: start\n", __func__);
-+ if (sm_inited) {
-+ /* Remove shared memory device.
-+ */
-+ vc_sm_remove_sharedmemory();
-+
-+ /* Remove all proc entries.
-+ */
-+ debugfs_remove_recursive(sm_state->dir_root);
-+
-+ /* Stop the videocore shared memory service.
-+ */
-+ vc_vchi_sm_stop(&sm_state->sm_handle);
-+
-+ /* Free the memory for the state structure.
-+ */
-+ mutex_destroy(&(sm_state->map_lock));
-+ kfree(sm_state);
-+ }
-+
-+ pr_debug("[%s]: end\n", __func__);
-+}
-+
-+#if defined(__KERNEL__)
-+/* Allocate a shared memory handle and block. */
-+int vc_sm_alloc(VC_SM_ALLOC_T *alloc, int *handle)
-+{
-+ struct vmcs_sm_ioctl_alloc ioparam = { 0 };
-+ int ret;
-+ struct SM_RESOURCE_T *resource;
-+
-+ /* Validate we can work with this device.
-+ */
-+ if (sm_state == NULL || alloc == NULL || handle == NULL) {
-+ pr_err("[%s]: invalid input\n", __func__);
-+ return -EPERM;
-+ }
-+
-+ ioparam.size = alloc->base_unit;
-+ ioparam.num = alloc->num_unit;
-+ ioparam.cached =
-+ alloc->type == VC_SM_ALLOC_CACHED ? VMCS_SM_CACHE_VC : 0;
-+
-+ ret = vc_sm_ioctl_alloc(sm_state->data_knl, &ioparam);
-+
-+ if (ret == 0) {
-+ resource =
-+ vmcs_sm_acquire_resource(sm_state->data_knl,
-+ ioparam.handle);
-+ if (resource) {
-+ resource->pid = 0;
-+ vmcs_sm_release_resource(resource, 0);
-+
-+ /* Assign valid handle at this time.
-+ */
-+ *handle = ioparam.handle;
-+ } else {
-+ ret = -ENOMEM;
-+ }
-+ }
-+
-+ return ret;
-+}
-+EXPORT_SYMBOL_GPL(vc_sm_alloc);
-+
-+/* Get an internal resource handle mapped from the external one.
-+*/
-+int vc_sm_int_handle(int handle)
-+{
-+ struct SM_RESOURCE_T *resource;
-+ int ret = 0;
-+
-+ /* Validate we can work with this device.
-+ */
-+ if (sm_state == NULL || handle == 0) {
-+ pr_err("[%s]: invalid input\n", __func__);
-+ return 0;
-+ }
-+
-+ /* Locate resource from GUID.
-+ */
-+ resource = vmcs_sm_acquire_resource(sm_state->data_knl, handle);
-+ if (resource) {
-+ ret = resource->res_handle;
-+ vmcs_sm_release_resource(resource, 0);
-+ }
-+
-+ return ret;
-+}
-+EXPORT_SYMBOL_GPL(vc_sm_int_handle);
-+
-+/* Free a previously allocated shared memory handle and block.
-+*/
-+int vc_sm_free(int handle)
-+{
-+ struct vmcs_sm_ioctl_free ioparam = { handle };
-+
-+ /* Validate we can work with this device.
-+ */
-+ if (sm_state == NULL || handle == 0) {
-+ pr_err("[%s]: invalid input\n", __func__);
-+ return -EPERM;
-+ }
-+
-+ return vc_sm_ioctl_free(sm_state->data_knl, &ioparam);
-+}
-+EXPORT_SYMBOL_GPL(vc_sm_free);
-+
-+/* Lock a memory handle for use by kernel.
-+*/
-+int vc_sm_lock(int handle, VC_SM_LOCK_CACHE_MODE_T mode,
-+ long unsigned int *data)
-+{
-+ struct vmcs_sm_ioctl_lock_unlock ioparam;
-+ int ret;
-+
-+ /* Validate we can work with this device.
-+ */
-+ if (sm_state == NULL || handle == 0 || data == NULL) {
-+ pr_err("[%s]: invalid input\n", __func__);
-+ return -EPERM;
-+ }
-+
-+ *data = 0;
-+
-+ ioparam.handle = handle;
-+ ret = vc_sm_ioctl_lock(sm_state->data_knl,
-+ &ioparam,
-+ 1,
-+ ((mode ==
-+ VC_SM_LOCK_CACHED) ? VMCS_SM_CACHE_HOST :
-+ VMCS_SM_CACHE_NONE), 0);
-+
-+ *data = ioparam.addr;
-+ return ret;
-+}
-+EXPORT_SYMBOL_GPL(vc_sm_lock);
-+
-+/* Unlock a memory handle in use by kernel.
-+*/
-+int vc_sm_unlock(int handle, int flush, int no_vc_unlock)
-+{
-+ struct vmcs_sm_ioctl_lock_unlock ioparam;
-+
-+ /* Validate we can work with this device.
-+ */
-+ if (sm_state == NULL || handle == 0) {
-+ pr_err("[%s]: invalid input\n", __func__);
-+ return -EPERM;
-+ }
-+
-+ ioparam.handle = handle;
-+ return vc_sm_ioctl_unlock(sm_state->data_knl,
-+ &ioparam, flush, 0, no_vc_unlock);
-+}
-+EXPORT_SYMBOL_GPL(vc_sm_unlock);
-+
-+/* Map a shared memory region for use by kernel.
-+*/
-+int vc_sm_map(int handle, unsigned int sm_addr, VC_SM_LOCK_CACHE_MODE_T mode,
-+ long unsigned int *data)
-+{
-+ struct vmcs_sm_ioctl_lock_unlock ioparam;
-+ int ret;
-+
-+ /* Validate we can work with this device.
-+ */
-+ if (sm_state == NULL || handle == 0 || data == NULL || sm_addr == 0) {
-+ pr_err("[%s]: invalid input\n", __func__);
-+ return -EPERM;
-+ }
-+
-+ *data = 0;
-+
-+ ioparam.handle = handle;
-+ ret = vc_sm_ioctl_lock(sm_state->data_knl,
-+ &ioparam,
-+ 1,
-+ ((mode ==
-+ VC_SM_LOCK_CACHED) ? VMCS_SM_CACHE_HOST :
-+ VMCS_SM_CACHE_NONE), sm_addr);
-+
-+ *data = ioparam.addr;
-+ return ret;
-+}
-+EXPORT_SYMBOL_GPL(vc_sm_map);
-+#endif
-+
-+late_initcall(vc_sm_init);
-+module_exit(vc_sm_exit);
-+
-+MODULE_AUTHOR("Broadcom");
-+MODULE_DESCRIPTION("VideoCore SharedMemory Driver");
-+MODULE_LICENSE("GPL v2");
---- /dev/null
-+++ b/include/linux/broadcom/vmcs_sm_ioctl.h
-@@ -0,0 +1,248 @@
-+/*****************************************************************************
-+* Copyright 2011 Broadcom Corporation. All rights reserved.
-+*
-+* Unless you and Broadcom execute a separate written software license
-+* agreement governing use of this software, this software is licensed to you
-+* under the terms of the GNU General Public License version 2, available at
-+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
-+*
-+* Notwithstanding the above, under no circumstances may you combine this
-+* software in any way with any other Broadcom software provided under a
-+* license other than the GPL, without Broadcom's express prior written
-+* consent.
-+*
-+*****************************************************************************/
-+
-+#if !defined(__VMCS_SM_IOCTL_H__INCLUDED__)
-+#define __VMCS_SM_IOCTL_H__INCLUDED__
-+
-+/* ---- Include Files ---------------------------------------------------- */
-+
-+#if defined(__KERNEL__)
-+#include <linux/types.h> /* Needed for standard types */
-+#else
-+#include <stdint.h>
-+#endif
-+
-+#include <linux/ioctl.h>
-+
-+/* ---- Constants and Types ---------------------------------------------- */
-+
-+#define VMCS_SM_RESOURCE_NAME 32
-+#define VMCS_SM_RESOURCE_NAME_DEFAULT "sm-host-resource"
-+
-+/* Type define used to create unique IOCTL number */
-+#define VMCS_SM_MAGIC_TYPE 'I'
-+
-+/* IOCTL commands */
-+enum vmcs_sm_cmd_e {
-+ VMCS_SM_CMD_ALLOC = 0x5A, /* Start at 0x5A arbitrarily */
-+ VMCS_SM_CMD_ALLOC_SHARE,
-+ VMCS_SM_CMD_LOCK,
-+ VMCS_SM_CMD_LOCK_CACHE,
-+ VMCS_SM_CMD_UNLOCK,
-+ VMCS_SM_CMD_RESIZE,
-+ VMCS_SM_CMD_UNMAP,
-+ VMCS_SM_CMD_FREE,
-+ VMCS_SM_CMD_FLUSH,
-+ VMCS_SM_CMD_INVALID,
-+
-+ VMCS_SM_CMD_SIZE_USR_HANDLE,
-+ VMCS_SM_CMD_CHK_USR_HANDLE,
-+
-+ VMCS_SM_CMD_MAPPED_USR_HANDLE,
-+ VMCS_SM_CMD_MAPPED_USR_ADDRESS,
-+ VMCS_SM_CMD_MAPPED_VC_HDL_FROM_ADDR,
-+ VMCS_SM_CMD_MAPPED_VC_HDL_FROM_HDL,
-+ VMCS_SM_CMD_MAPPED_VC_ADDR_FROM_HDL,
-+
-+ VMCS_SM_CMD_VC_WALK_ALLOC,
-+ VMCS_SM_CMD_HOST_WALK_MAP,
-+ VMCS_SM_CMD_HOST_WALK_PID_ALLOC,
-+ VMCS_SM_CMD_HOST_WALK_PID_MAP,
-+
-+ VMCS_SM_CMD_CLEAN_INVALID,
-+
-+ VMCS_SM_CMD_LAST /* Do no delete */
-+};
-+
-+/* Cache type supported, conveniently matches the user space definition in
-+** user-vcsm.h.
-+*/
-+enum vmcs_sm_cache_e {
-+ VMCS_SM_CACHE_NONE,
-+ VMCS_SM_CACHE_HOST,
-+ VMCS_SM_CACHE_VC,
-+ VMCS_SM_CACHE_BOTH,
-+};
-+
-+/* IOCTL Data structures */
-+struct vmcs_sm_ioctl_alloc {
-+ /* user -> kernel */
-+ unsigned int size;
-+ unsigned int num;
-+ enum vmcs_sm_cache_e cached;
-+ char name[VMCS_SM_RESOURCE_NAME];
-+
-+ /* kernel -> user */
-+ unsigned int handle;
-+ /* unsigned int base_addr; */
-+};
-+
-+struct vmcs_sm_ioctl_alloc_share {
-+ /* user -> kernel */
-+ unsigned int handle;
-+ unsigned int size;
-+};
-+
-+struct vmcs_sm_ioctl_free {
-+ /* user -> kernel */
-+ unsigned int handle;
-+ /* unsigned int base_addr; */
-+};
-+
-+struct vmcs_sm_ioctl_lock_unlock {
-+ /* user -> kernel */
-+ unsigned int handle;
-+
-+ /* kernel -> user */
-+ unsigned int addr;
-+};
-+
-+struct vmcs_sm_ioctl_lock_cache {
-+ /* user -> kernel */
-+ unsigned int handle;
-+ enum vmcs_sm_cache_e cached;
-+};
-+
-+struct vmcs_sm_ioctl_resize {
-+ /* user -> kernel */
-+ unsigned int handle;
-+ unsigned int new_size;
-+
-+ /* kernel -> user */
-+ unsigned int old_size;
-+};
-+
-+struct vmcs_sm_ioctl_map {
-+ /* user -> kernel */
-+ /* and kernel -> user */
-+ unsigned int pid;
-+ unsigned int handle;
-+ unsigned int addr;
-+
-+ /* kernel -> user */
-+ unsigned int size;
-+};
-+
-+struct vmcs_sm_ioctl_walk {
-+ /* user -> kernel */
-+ unsigned int pid;
-+};
-+
-+struct vmcs_sm_ioctl_chk {
-+ /* user -> kernel */
-+ unsigned int handle;
-+
-+ /* kernel -> user */
-+ unsigned int addr;
-+ unsigned int size;
-+ enum vmcs_sm_cache_e cache;
-+};
-+
-+struct vmcs_sm_ioctl_size {
-+ /* user -> kernel */
-+ unsigned int handle;
-+
-+ /* kernel -> user */
-+ unsigned int size;
-+};
-+
-+struct vmcs_sm_ioctl_cache {
-+ /* user -> kernel */
-+ unsigned int handle;
-+ unsigned int addr;
-+ unsigned int size;
-+};
-+
-+struct vmcs_sm_ioctl_clean_invalid {
-+ /* user -> kernel */
-+ struct {
-+ unsigned int cmd;
-+ unsigned int handle;
-+ unsigned int addr;
-+ unsigned int size;
-+ } s[8];
-+};
-+
-+/* IOCTL numbers */
-+#define VMCS_SM_IOCTL_MEM_ALLOC\
-+ _IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_ALLOC,\
-+ struct vmcs_sm_ioctl_alloc)
-+#define VMCS_SM_IOCTL_MEM_ALLOC_SHARE\
-+ _IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_ALLOC_SHARE,\
-+ struct vmcs_sm_ioctl_alloc_share)
-+#define VMCS_SM_IOCTL_MEM_LOCK\
-+ _IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_LOCK,\
-+ struct vmcs_sm_ioctl_lock_unlock)
-+#define VMCS_SM_IOCTL_MEM_LOCK_CACHE\
-+ _IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_LOCK_CACHE,\
-+ struct vmcs_sm_ioctl_lock_cache)
-+#define VMCS_SM_IOCTL_MEM_UNLOCK\
-+ _IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_UNLOCK,\
-+ struct vmcs_sm_ioctl_lock_unlock)
-+#define VMCS_SM_IOCTL_MEM_RESIZE\
-+ _IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_RESIZE,\
-+ struct vmcs_sm_ioctl_resize)
-+#define VMCS_SM_IOCTL_MEM_FREE\
-+ _IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_FREE,\
-+ struct vmcs_sm_ioctl_free)
-+#define VMCS_SM_IOCTL_MEM_FLUSH\
-+ _IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_FLUSH,\
-+ struct vmcs_sm_ioctl_cache)
-+#define VMCS_SM_IOCTL_MEM_INVALID\
-+ _IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_INVALID,\
-+ struct vmcs_sm_ioctl_cache)
-+#define VMCS_SM_IOCTL_MEM_CLEAN_INVALID\
-+ _IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_CLEAN_INVALID,\
-+ struct vmcs_sm_ioctl_clean_invalid)
-+
-+#define VMCS_SM_IOCTL_SIZE_USR_HDL\
-+ _IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_SIZE_USR_HANDLE,\
-+ struct vmcs_sm_ioctl_size)
-+#define VMCS_SM_IOCTL_CHK_USR_HDL\
-+ _IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_CHK_USR_HANDLE,\
-+ struct vmcs_sm_ioctl_chk)
-+
-+#define VMCS_SM_IOCTL_MAP_USR_HDL\
-+ _IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_MAPPED_USR_HANDLE,\
-+ struct vmcs_sm_ioctl_map)
-+#define VMCS_SM_IOCTL_MAP_USR_ADDRESS\
-+ _IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_MAPPED_USR_ADDRESS,\
-+ struct vmcs_sm_ioctl_map)
-+#define VMCS_SM_IOCTL_MAP_VC_HDL_FR_ADDR\
-+ _IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_MAPPED_VC_HDL_FROM_ADDR,\
-+ struct vmcs_sm_ioctl_map)
-+#define VMCS_SM_IOCTL_MAP_VC_HDL_FR_HDL\
-+ _IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_MAPPED_VC_HDL_FROM_HDL,\
-+ struct vmcs_sm_ioctl_map)
-+#define VMCS_SM_IOCTL_MAP_VC_ADDR_FR_HDL\
-+ _IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_MAPPED_VC_ADDR_FROM_HDL,\
-+ struct vmcs_sm_ioctl_map)
-+
-+#define VMCS_SM_IOCTL_VC_WALK_ALLOC\
-+ _IO(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_VC_WALK_ALLOC)
-+#define VMCS_SM_IOCTL_HOST_WALK_MAP\
-+ _IO(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_HOST_WALK_MAP)
-+#define VMCS_SM_IOCTL_HOST_WALK_PID_ALLOC\
-+ _IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_HOST_WALK_PID_ALLOC,\
-+ struct vmcs_sm_ioctl_walk)
-+#define VMCS_SM_IOCTL_HOST_WALK_PID_MAP\
-+ _IOR(VMCS_SM_MAGIC_TYPE, VMCS_SM_CMD_HOST_WALK_PID_MAP,\
-+ struct vmcs_sm_ioctl_walk)
-+
-+/* ---- Variable Externs ------------------------------------------------- */
-+
-+/* ---- Function Prototypes ---------------------------------------------- */
-+
-+#endif /* __VMCS_SM_IOCTL_H__INCLUDED__ */
diff --git a/target/linux/brcm2708/patches-4.4/0039-Add-dev-gpiomem-device-for-rootless-user-GPIO-access.patch b/target/linux/brcm2708/patches-4.4/0039-Add-dev-gpiomem-device-for-rootless-user-GPIO-access.patch
deleted file mode 100644
index 7622007..0000000
--- a/target/linux/brcm2708/patches-4.4/0039-Add-dev-gpiomem-device-for-rootless-user-GPIO-access.patch
+++ /dev/null
@@ -1,306 +0,0 @@
-From f0d2dd1294f41beea8b495625f6a299a0274dae5 Mon Sep 17 00:00:00 2001
-From: Luke Wren <luke at raspberrypi.org>
-Date: Fri, 21 Aug 2015 23:14:48 +0100
-Subject: [PATCH] Add /dev/gpiomem device for rootless user GPIO access
-
-Signed-off-by: Luke Wren <luke at raspberrypi.org>
-
-bcm2835-gpiomem: Fix for ARCH_BCM2835 builds
-
-Build on ARCH_BCM2835, and fail to probe if no IO resource.
-
-See: https://github.com/raspberrypi/linux/issues/1154
----
- drivers/char/broadcom/Kconfig | 9 ++
- drivers/char/broadcom/Makefile | 3 +
- drivers/char/broadcom/bcm2835-gpiomem.c | 260 ++++++++++++++++++++++++++++++++
- 3 files changed, 272 insertions(+)
- create mode 100644 drivers/char/broadcom/bcm2835-gpiomem.c
-
---- a/drivers/char/broadcom/Kconfig
-+++ b/drivers/char/broadcom/Kconfig
-@@ -32,3 +32,12 @@ config BCM_VC_SM
- help
- Support for the VC shared memory on the Broadcom reference
- design. Uses the VCHIQ stack.
-+
-+config BCM2835_DEVGPIOMEM
-+ tristate "/dev/gpiomem rootless GPIO access via mmap() on the BCM2835"
-+ default m
-+ help
-+ Provides users with root-free access to the GPIO registers
-+ on the 2835. Calling mmap(/dev/gpiomem) will map the GPIO
-+ register page to the user's pointer.
-+
---- a/drivers/char/broadcom/Makefile
-+++ b/drivers/char/broadcom/Makefile
-@@ -1,3 +1,6 @@
- obj-$(CONFIG_BCM_VC_CMA) += vc_cma/
- obj-$(CONFIG_BCM2708_VCMEM) += vc_mem.o
- obj-$(CONFIG_BCM_VC_SM) += vc_sm/
-+
-+obj-$(CONFIG_BCM2835_DEVGPIOMEM)+= bcm2835-gpiomem.o
-+
---- /dev/null
-+++ b/drivers/char/broadcom/bcm2835-gpiomem.c
-@@ -0,0 +1,260 @@
-+/**
-+ * GPIO memory device driver
-+ *
-+ * Creates a chardev /dev/gpiomem which will provide user access to
-+ * the BCM2835's GPIO registers when it is mmap()'d.
-+ * No longer need root for user GPIO access, but without relaxing permissions
-+ * on /dev/mem.
-+ *
-+ * Written by Luke Wren <luke at raspberrypi.org>
-+ * Copyright (c) 2015, Raspberry Pi (Trading) Ltd.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+#include <linux/of.h>
-+#include <linux/platform_device.h>
-+#include <linux/mm.h>
-+#include <linux/slab.h>
-+#include <linux/cdev.h>
-+#include <linux/pagemap.h>
-+#include <linux/io.h>
-+
-+#define DEVICE_NAME "bcm2835-gpiomem"
-+#define DRIVER_NAME "gpiomem-bcm2835"
-+#define DEVICE_MINOR 0
-+
-+struct bcm2835_gpiomem_instance {
-+ unsigned long gpio_regs_phys;
-+ struct device *dev;
-+};
-+
-+static struct cdev bcm2835_gpiomem_cdev;
-+static dev_t bcm2835_gpiomem_devid;
-+static struct class *bcm2835_gpiomem_class;
-+static struct device *bcm2835_gpiomem_dev;
-+static struct bcm2835_gpiomem_instance *inst;
-+
-+
-+/****************************************************************************
-+*
-+* GPIO mem chardev file ops
-+*
-+***************************************************************************/
-+
-+static int bcm2835_gpiomem_open(struct inode *inode, struct file *file)
-+{
-+ int dev = iminor(inode);
-+ int ret = 0;
-+
-+ dev_info(inst->dev, "gpiomem device opened.");
-+
-+ if (dev != DEVICE_MINOR) {
-+ dev_err(inst->dev, "Unknown minor device: %d", dev);
-+ ret = -ENXIO;
-+ }
-+ return ret;
-+}
-+
-+static int bcm2835_gpiomem_release(struct inode *inode, struct file *file)
-+{
-+ int dev = iminor(inode);
-+ int ret = 0;
-+
-+ if (dev != DEVICE_MINOR) {
-+ dev_err(inst->dev, "Unknown minor device %d", dev);
-+ ret = -ENXIO;
-+ }
-+ return ret;
-+}
-+
-+static const struct vm_operations_struct bcm2835_gpiomem_vm_ops = {
-+#ifdef CONFIG_HAVE_IOREMAP_PROT
-+ .access = generic_access_phys
-+#endif
-+};
-+
-+static int bcm2835_gpiomem_mmap(struct file *file, struct vm_area_struct *vma)
-+{
-+ /* Ignore what the user says - they're getting the GPIO regs
-+ whether they like it or not! */
-+ unsigned long gpio_page = inst->gpio_regs_phys >> PAGE_SHIFT;
-+
-+ vma->vm_page_prot = phys_mem_access_prot(file, gpio_page,
-+ PAGE_SIZE,
-+ vma->vm_page_prot);
-+ vma->vm_ops = &bcm2835_gpiomem_vm_ops;
-+ if (remap_pfn_range(vma, vma->vm_start,
-+ gpio_page,
-+ PAGE_SIZE,
-+ vma->vm_page_prot)) {
-+ return -EAGAIN;
-+ }
-+ return 0;
-+}
-+
-+static const struct file_operations
-+bcm2835_gpiomem_fops = {
-+ .owner = THIS_MODULE,
-+ .open = bcm2835_gpiomem_open,
-+ .release = bcm2835_gpiomem_release,
-+ .mmap = bcm2835_gpiomem_mmap,
-+};
-+
-+
-+ /****************************************************************************
-+*
-+* Probe and remove functions
-+*
-+***************************************************************************/
-+
-+
-+static int bcm2835_gpiomem_probe(struct platform_device *pdev)
-+{
-+ int err;
-+ void *ptr_err;
-+ struct device *dev = &pdev->dev;
-+ struct resource *ioresource;
-+
-+ /* Allocate buffers and instance data */
-+
-+ inst = kzalloc(sizeof(struct bcm2835_gpiomem_instance), GFP_KERNEL);
-+
-+ if (!inst) {
-+ err = -ENOMEM;
-+ goto failed_inst_alloc;
-+ }
-+
-+ inst->dev = dev;
-+
-+ ioresource = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+ if (ioresource) {
-+ inst->gpio_regs_phys = ioresource->start;
-+ } else {
-+ dev_err(inst->dev, "failed to get IO resource");
-+ err = -ENOENT;
-+ goto failed_get_resource;
-+ }
-+
-+ /* Create character device entries */
-+
-+ err = alloc_chrdev_region(&bcm2835_gpiomem_devid,
-+ DEVICE_MINOR, 1, DEVICE_NAME);
-+ if (err != 0) {
-+ dev_err(inst->dev, "unable to allocate device number");
-+ goto failed_alloc_chrdev;
-+ }
-+ cdev_init(&bcm2835_gpiomem_cdev, &bcm2835_gpiomem_fops);
-+ bcm2835_gpiomem_cdev.owner = THIS_MODULE;
-+ err = cdev_add(&bcm2835_gpiomem_cdev, bcm2835_gpiomem_devid, 1);
-+ if (err != 0) {
-+ dev_err(inst->dev, "unable to register device");
-+ goto failed_cdev_add;
-+ }
-+
-+ /* Create sysfs entries */
-+
-+ bcm2835_gpiomem_class = class_create(THIS_MODULE, DEVICE_NAME);
-+ ptr_err = bcm2835_gpiomem_class;
-+ if (IS_ERR(ptr_err))
-+ goto failed_class_create;
-+
-+ bcm2835_gpiomem_dev = device_create(bcm2835_gpiomem_class, NULL,
-+ bcm2835_gpiomem_devid, NULL,
-+ "gpiomem");
-+ ptr_err = bcm2835_gpiomem_dev;
-+ if (IS_ERR(ptr_err))
-+ goto failed_device_create;
-+
-+ dev_info(inst->dev, "Initialised: Registers at 0x%08lx",
-+ inst->gpio_regs_phys);
-+
-+ return 0;
-+
-+failed_device_create:
-+ class_destroy(bcm2835_gpiomem_class);
-+failed_class_create:
-+ cdev_del(&bcm2835_gpiomem_cdev);
-+ err = PTR_ERR(ptr_err);
-+failed_cdev_add:
-+ unregister_chrdev_region(bcm2835_gpiomem_devid, 1);
-+failed_alloc_chrdev:
-+failed_get_resource:
-+ kfree(inst);
-+failed_inst_alloc:
-+ dev_err(inst->dev, "could not load bcm2835_gpiomem");
-+ return err;
-+}
-+
-+static int bcm2835_gpiomem_remove(struct platform_device *pdev)
-+{
-+ struct device *dev = inst->dev;
-+
-+ kfree(inst);
-+ device_destroy(bcm2835_gpiomem_class, bcm2835_gpiomem_devid);
-+ class_destroy(bcm2835_gpiomem_class);
-+ cdev_del(&bcm2835_gpiomem_cdev);
-+ unregister_chrdev_region(bcm2835_gpiomem_devid, 1);
-+
-+ dev_info(dev, "GPIO mem driver removed - OK");
-+ return 0;
-+}
-+
-+ /****************************************************************************
-+*
-+* Register the driver with device tree
-+*
-+***************************************************************************/
-+
-+static const struct of_device_id bcm2835_gpiomem_of_match[] = {
-+ {.compatible = "brcm,bcm2835-gpiomem",},
-+ { /* sentinel */ },
-+};
-+
-+MODULE_DEVICE_TABLE(of, bcm2835_gpiomem_of_match);
-+
-+static struct platform_driver bcm2835_gpiomem_driver = {
-+ .probe = bcm2835_gpiomem_probe,
-+ .remove = bcm2835_gpiomem_remove,
-+ .driver = {
-+ .name = DRIVER_NAME,
-+ .owner = THIS_MODULE,
-+ .of_match_table = bcm2835_gpiomem_of_match,
-+ },
-+};
-+
-+module_platform_driver(bcm2835_gpiomem_driver);
-+
-+MODULE_ALIAS("platform:gpiomem-bcm2835");
-+MODULE_LICENSE("GPL");
-+MODULE_DESCRIPTION("gpiomem driver for accessing GPIO from userspace");
-+MODULE_AUTHOR("Luke Wren <luke at raspberrypi.org>");
diff --git a/target/linux/brcm2708/patches-4.4/0040-Add-SMI-driver.patch b/target/linux/brcm2708/patches-4.4/0040-Add-SMI-driver.patch
deleted file mode 100644
index 4ef07ac..0000000
--- a/target/linux/brcm2708/patches-4.4/0040-Add-SMI-driver.patch
+++ /dev/null
@@ -1,1930 +0,0 @@
-From 2ddd11a5a4d40a51e075c4aa37932adfc152cde3 Mon Sep 17 00:00:00 2001
-From: Luke Wren <wren6991 at gmail.com>
-Date: Sat, 5 Sep 2015 01:14:45 +0100
-Subject: [PATCH] Add SMI driver
-
-Signed-off-by: Luke Wren <wren6991 at gmail.com>
----
- .../bindings/misc/brcm,bcm2835-smi-dev.txt | 17 +
- .../devicetree/bindings/misc/brcm,bcm2835-smi.txt | 48 +
- drivers/char/broadcom/Kconfig | 8 +
- drivers/char/broadcom/Makefile | 2 +-
- drivers/char/broadcom/bcm2835_smi_dev.c | 402 +++++++++
- drivers/misc/Kconfig | 8 +
- drivers/misc/Makefile | 1 +
- drivers/misc/bcm2835_smi.c | 985 +++++++++++++++++++++
- include/linux/broadcom/bcm2835_smi.h | 391 ++++++++
- 9 files changed, 1861 insertions(+), 1 deletion(-)
- create mode 100644 Documentation/devicetree/bindings/misc/brcm,bcm2835-smi-dev.txt
- create mode 100644 Documentation/devicetree/bindings/misc/brcm,bcm2835-smi.txt
- create mode 100644 drivers/char/broadcom/bcm2835_smi_dev.c
- create mode 100644 drivers/misc/bcm2835_smi.c
- create mode 100644 include/linux/broadcom/bcm2835_smi.h
-
---- /dev/null
-+++ b/Documentation/devicetree/bindings/misc/brcm,bcm2835-smi-dev.txt
-@@ -0,0 +1,17 @@
-+* Broadcom BCM2835 SMI character device driver.
-+
-+SMI or secondary memory interface is a peripheral specific to certain Broadcom
-+SOCs, and is helpful for talking to things like parallel-interface displays
-+and NAND flashes (in fact, most things with a parallel register interface).
-+
-+This driver adds a character device which provides a user-space interface to
-+an instance of the SMI driver.
-+
-+Required properties:
-+- compatible: "brcm,bcm2835-smi-dev"
-+- smi_handle: a phandle to the smi node.
-+
-+Optional properties:
-+- None.
-+
-+
---- /dev/null
-+++ b/Documentation/devicetree/bindings/misc/brcm,bcm2835-smi.txt
-@@ -0,0 +1,48 @@
-+* Broadcom BCM2835 SMI driver.
-+
-+SMI or secondary memory interface is a peripheral specific to certain Broadcom
-+SOCs, and is helpful for talking to things like parallel-interface displays
-+and NAND flashes (in fact, most things with a parallel register interface).
-+
-+Required properties:
-+- compatible: "brcm,bcm2835-smi"
-+- reg: Should contain location and length of SMI registers and SMI clkman regs
-+- interrupts: *the* SMI interrupt.
-+- pinctrl-names: should be "default".
-+- pinctrl-0: the phandle of the gpio pin node.
-+- brcm,smi-clock-source: the clock source for clkman
-+- brcm,smi-clock-divisor: the integer clock divisor for clkman
-+- dmas: the dma controller phandle and the DREQ number (4 on a 2835)
-+- dma-names: the name used by the driver to request its channel.
-+ Should be "rx-tx".
-+
-+Optional properties:
-+- None.
-+
-+Examples:
-+
-+8 data pin configuration:
-+
-+smi: smi at 7e600000 {
-+ compatible = "brcm,bcm2835-smi";
-+ reg = <0x7e600000 0x44>, <0x7e1010b0 0x8>;
-+ interrupts = <2 16>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&smi_pins>;
-+ brcm,smi-clock-source = <6>;
-+ brcm,smi-clock-divisor = <4>;
-+ dmas = <&dma 4>;
-+ dma-names = "rx-tx";
-+
-+ status = "okay";
-+};
-+
-+smi_pins: smi_pins {
-+ brcm,pins = <2 3 4 5 6 7 8 9 10 11 12 13 14 15>;
-+ /* Alt 1: SMI */
-+ brcm,function = <5 5 5 5 5 5 5 5 5 5 5 5 5 5>;
-+ /* /CS, /WE and /OE are pulled high, as they are
-+ generally active low signals */
-+ brcm,pull = <2 2 2 2 2 2 0 0 0 0 0 0 0 0>;
-+};
-+
---- a/drivers/char/broadcom/Kconfig
-+++ b/drivers/char/broadcom/Kconfig
-@@ -41,3 +41,11 @@ config BCM2835_DEVGPIOMEM
- on the 2835. Calling mmap(/dev/gpiomem) will map the GPIO
- register page to the user's pointer.
-
-+config BCM2835_SMI_DEV
-+ tristate "Character device driver for BCM2835 Secondary Memory Interface"
-+ depends on (MACH_BCM2708 || MACH_BCM2709 || ARCH_BCM2835) && BCM2835_SMI
-+ default m
-+ help
-+ This driver provides a character device interface (ioctl + read/write) to
-+ Broadcom's Secondary Memory interface. The low-level functionality is provided
-+ by the SMI driver itself.
---- a/drivers/char/broadcom/Makefile
-+++ b/drivers/char/broadcom/Makefile
-@@ -3,4 +3,4 @@ obj-$(CONFIG_BCM2708_VCMEM) += vc_mem.o
- obj-$(CONFIG_BCM_VC_SM) += vc_sm/
-
- obj-$(CONFIG_BCM2835_DEVGPIOMEM)+= bcm2835-gpiomem.o
--
-+obj-$(CONFIG_BCM2835_SMI_DEV) += bcm2835_smi_dev.o
---- /dev/null
-+++ b/drivers/char/broadcom/bcm2835_smi_dev.c
-@@ -0,0 +1,402 @@
-+/**
-+ * Character device driver for Broadcom Secondary Memory Interface
-+ *
-+ * Written by Luke Wren <luke at raspberrypi.org>
-+ * Copyright (c) 2015, Raspberry Pi (Trading) Ltd.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+#include <linux/of.h>
-+#include <linux/platform_device.h>
-+#include <linux/slab.h>
-+#include <linux/mm.h>
-+#include <linux/pagemap.h>
-+#include <linux/fs.h>
-+#include <linux/cdev.h>
-+#include <linux/fs.h>
-+
-+#include <linux/broadcom/bcm2835_smi.h>
-+
-+#define DEVICE_NAME "bcm2835-smi-dev"
-+#define DRIVER_NAME "smi-dev-bcm2835"
-+#define DEVICE_MINOR 0
-+
-+static struct cdev bcm2835_smi_cdev;
-+static dev_t bcm2835_smi_devid;
-+static struct class *bcm2835_smi_class;
-+static struct device *bcm2835_smi_dev;
-+
-+struct bcm2835_smi_dev_instance {
-+ struct device *dev;
-+};
-+
-+static struct bcm2835_smi_instance *smi_inst;
-+static struct bcm2835_smi_dev_instance *inst;
-+
-+static const char *const ioctl_names[] = {
-+ "READ_SETTINGS",
-+ "WRITE_SETTINGS",
-+ "ADDRESS"
-+};
-+
-+/****************************************************************************
-+*
-+* SMI chardev file ops
-+*
-+***************************************************************************/
-+static long
-+bcm2835_smi_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
-+{
-+ long ret = 0;
-+
-+ dev_info(inst->dev, "serving ioctl...");
-+
-+ switch (cmd) {
-+ case BCM2835_SMI_IOC_GET_SETTINGS:{
-+ struct smi_settings *settings;
-+
-+ dev_info(inst->dev, "Reading SMI settings to user.");
-+ settings = bcm2835_smi_get_settings_from_regs(smi_inst);
-+ if (copy_to_user((void *)arg, settings,
-+ sizeof(struct smi_settings)))
-+ dev_err(inst->dev, "settings copy failed.");
-+ break;
-+ }
-+ case BCM2835_SMI_IOC_WRITE_SETTINGS:{
-+ struct smi_settings *settings;
-+
-+ dev_info(inst->dev, "Setting user's SMI settings.");
-+ settings = bcm2835_smi_get_settings_from_regs(smi_inst);
-+ if (copy_from_user(settings, (void *)arg,
-+ sizeof(struct smi_settings)))
-+ dev_err(inst->dev, "settings copy failed.");
-+ else
-+ bcm2835_smi_set_regs_from_settings(smi_inst);
-+ break;
-+ }
-+ case BCM2835_SMI_IOC_ADDRESS:
-+ dev_info(inst->dev, "SMI address set: 0x%02x", (int)arg);
-+ bcm2835_smi_set_address(smi_inst, arg);
-+ break;
-+ default:
-+ dev_err(inst->dev, "invalid ioctl cmd: %d", cmd);
-+ ret = -ENOTTY;
-+ break;
-+ }
-+
-+ return ret;
-+}
-+
-+static int bcm2835_smi_open(struct inode *inode, struct file *file)
-+{
-+ int dev = iminor(inode);
-+
-+ dev_dbg(inst->dev, "SMI device opened.");
-+
-+ if (dev != DEVICE_MINOR) {
-+ dev_err(inst->dev,
-+ "bcm2835_smi_release: Unknown minor device: %d",
-+ dev);
-+ return -ENXIO;
-+ }
-+
-+ return 0;
-+}
-+
-+static int bcm2835_smi_release(struct inode *inode, struct file *file)
-+{
-+ int dev = iminor(inode);
-+
-+ if (dev != DEVICE_MINOR) {
-+ dev_err(inst->dev,
-+ "bcm2835_smi_release: Unknown minor device %d", dev);
-+ return -ENXIO;
-+ }
-+
-+ return 0;
-+}
-+
-+static ssize_t dma_bounce_user(
-+ enum dma_transfer_direction dma_dir,
-+ char __user *user_ptr,
-+ size_t count,
-+ struct bcm2835_smi_bounce_info *bounce)
-+{
-+ int chunk_size;
-+ int chunk_no = 0;
-+ int count_left = count;
-+
-+ while (count_left) {
-+ int rv;
-+ void *buf;
-+
-+ /* Wait for current chunk to complete: */
-+ if (down_timeout(&bounce->callback_sem,
-+ msecs_to_jiffies(1000))) {
-+ dev_err(inst->dev, "DMA bounce timed out");
-+ count -= (count_left);
-+ break;
-+ }
-+
-+ if (bounce->callback_sem.count >= DMA_BOUNCE_BUFFER_COUNT - 1)
-+ dev_err(inst->dev, "WARNING: Ring buffer overflow");
-+ chunk_size = count_left > DMA_BOUNCE_BUFFER_SIZE ?
-+ DMA_BOUNCE_BUFFER_SIZE : count_left;
-+ buf = bounce->buffer[chunk_no % DMA_BOUNCE_BUFFER_COUNT];
-+ if (dma_dir == DMA_DEV_TO_MEM)
-+ rv = copy_to_user(user_ptr, buf, chunk_size);
-+ else
-+ rv = copy_from_user(buf, user_ptr, chunk_size);
-+ if (rv)
-+ dev_err(inst->dev, "copy_*_user() failed!: %d", rv);
-+ user_ptr += chunk_size;
-+ count_left -= chunk_size;
-+ chunk_no++;
-+ }
-+ return count;
-+}
-+
-+static ssize_t
-+bcm2835_read_file(struct file *f, char __user *user_ptr,
-+ size_t count, loff_t *offs)
-+{
-+ int odd_bytes;
-+
-+ dev_dbg(inst->dev, "User reading %d bytes from SMI.", count);
-+ /* We don't want to DMA a number of bytes % 4 != 0 (32 bit FIFO) */
-+ if (count > DMA_THRESHOLD_BYTES)
-+ odd_bytes = count & 0x3;
-+ else
-+ odd_bytes = count;
-+ count -= odd_bytes;
-+ if (count) {
-+ struct bcm2835_smi_bounce_info *bounce;
-+
-+ count = bcm2835_smi_user_dma(smi_inst,
-+ DMA_DEV_TO_MEM, user_ptr, count,
-+ &bounce);
-+ if (count)
-+ count = dma_bounce_user(DMA_DEV_TO_MEM, user_ptr,
-+ count, bounce);
-+ }
-+ if (odd_bytes) {
-+ /* Read from FIFO directly if not using DMA */
-+ uint8_t buf[DMA_THRESHOLD_BYTES];
-+
-+ bcm2835_smi_read_buf(smi_inst, buf, odd_bytes);
-+ if (copy_to_user(user_ptr, buf, odd_bytes))
-+ dev_err(inst->dev, "copy_to_user() failed.");
-+ count += odd_bytes;
-+
-+ }
-+ return count;
-+}
-+
-+static ssize_t
-+bcm2835_write_file(struct file *f, const char __user *user_ptr,
-+ size_t count, loff_t *offs)
-+{
-+ int odd_bytes;
-+
-+ dev_dbg(inst->dev, "User writing %d bytes to SMI.", count);
-+ if (count > DMA_THRESHOLD_BYTES)
-+ odd_bytes = count & 0x3;
-+ else
-+ odd_bytes = count;
-+ count -= odd_bytes;
-+ if (count) {
-+ struct bcm2835_smi_bounce_info *bounce;
-+
-+ count = bcm2835_smi_user_dma(smi_inst,
-+ DMA_MEM_TO_DEV, (char __user *)user_ptr, count,
-+ &bounce);
-+ if (count)
-+ count = dma_bounce_user(DMA_MEM_TO_DEV,
-+ (char __user *)user_ptr,
-+ count, bounce);
-+ }
-+ if (odd_bytes) {
-+ uint8_t buf[DMA_THRESHOLD_BYTES];
-+
-+ if (copy_from_user(buf, user_ptr, odd_bytes))
-+ dev_err(inst->dev, "copy_from_user() failed.");
-+ else
-+ bcm2835_smi_write_buf(smi_inst, buf, odd_bytes);
-+ count += odd_bytes;
-+ }
-+ return count;
-+}
-+
-+static const struct file_operations
-+bcm2835_smi_fops = {
-+ .owner = THIS_MODULE,
-+ .unlocked_ioctl = bcm2835_smi_ioctl,
-+ .open = bcm2835_smi_open,
-+ .release = bcm2835_smi_release,
-+ .read = bcm2835_read_file,
-+ .write = bcm2835_write_file,
-+};
-+
-+
-+/****************************************************************************
-+*
-+* bcm2835_smi_probe - called when the driver is loaded.
-+*
-+***************************************************************************/
-+
-+static int bcm2835_smi_dev_probe(struct platform_device *pdev)
-+{
-+ int err;
-+ void *ptr_err;
-+ struct device *dev = &pdev->dev;
-+ struct device_node *node = dev->of_node, *smi_node;
-+
-+ if (!node) {
-+ dev_err(dev, "No device tree node supplied!");
-+ return -EINVAL;
-+ }
-+
-+ smi_node = of_parse_phandle(node, "smi_handle", 0);
-+
-+ if (!smi_node) {
-+ dev_err(dev, "No such property: smi_handle");
-+ return -ENXIO;
-+ }
-+
-+ smi_inst = bcm2835_smi_get(smi_node);
-+
-+ if (!smi_inst)
-+ return -EPROBE_DEFER;
-+
-+ /* Allocate buffers and instance data */
-+
-+ inst = devm_kzalloc(dev, sizeof(*inst), GFP_KERNEL);
-+
-+ if (!inst)
-+ return -ENOMEM;
-+
-+ inst->dev = dev;
-+
-+ /* Create character device entries */
-+
-+ err = alloc_chrdev_region(&bcm2835_smi_devid,
-+ DEVICE_MINOR, 1, DEVICE_NAME);
-+ if (err != 0) {
-+ dev_err(inst->dev, "unable to allocate device number");
-+ return -ENOMEM;
-+ }
-+ cdev_init(&bcm2835_smi_cdev, &bcm2835_smi_fops);
-+ bcm2835_smi_cdev.owner = THIS_MODULE;
-+ err = cdev_add(&bcm2835_smi_cdev, bcm2835_smi_devid, 1);
-+ if (err != 0) {
-+ dev_err(inst->dev, "unable to register device");
-+ err = -ENOMEM;
-+ goto failed_cdev_add;
-+ }
-+
-+ /* Create sysfs entries */
-+
-+ bcm2835_smi_class = class_create(THIS_MODULE, DEVICE_NAME);
-+ ptr_err = bcm2835_smi_class;
-+ if (IS_ERR(ptr_err))
-+ goto failed_class_create;
-+
-+ bcm2835_smi_dev = device_create(bcm2835_smi_class, NULL,
-+ bcm2835_smi_devid, NULL,
-+ "smi");
-+ ptr_err = bcm2835_smi_dev;
-+ if (IS_ERR(ptr_err))
-+ goto failed_device_create;
-+
-+ dev_info(inst->dev, "initialised");
-+
-+ return 0;
-+
-+failed_device_create:
-+ class_destroy(bcm2835_smi_class);
-+failed_class_create:
-+ cdev_del(&bcm2835_smi_cdev);
-+ err = PTR_ERR(ptr_err);
-+failed_cdev_add:
-+ unregister_chrdev_region(bcm2835_smi_devid, 1);
-+ dev_err(dev, "could not load bcm2835_smi_dev");
-+ return err;
-+}
-+
-+/****************************************************************************
-+*
-+* bcm2835_smi_remove - called when the driver is unloaded.
-+*
-+***************************************************************************/
-+
-+static int bcm2835_smi_dev_remove(struct platform_device *pdev)
-+{
-+ device_destroy(bcm2835_smi_class, bcm2835_smi_devid);
-+ class_destroy(bcm2835_smi_class);
-+ cdev_del(&bcm2835_smi_cdev);
-+ unregister_chrdev_region(bcm2835_smi_devid, 1);
-+
-+ dev_info(inst->dev, "SMI character dev removed - OK");
-+ return 0;
-+}
-+
-+/****************************************************************************
-+*
-+* Register the driver with device tree
-+*
-+***************************************************************************/
-+
-+static const struct of_device_id bcm2835_smi_dev_of_match[] = {
-+ {.compatible = "brcm,bcm2835-smi-dev",},
-+ { /* sentinel */ },
-+};
-+
-+MODULE_DEVICE_TABLE(of, bcm2835_smi_dev_of_match);
-+
-+static struct platform_driver bcm2835_smi_dev_driver = {
-+ .probe = bcm2835_smi_dev_probe,
-+ .remove = bcm2835_smi_dev_remove,
-+ .driver = {
-+ .name = DRIVER_NAME,
-+ .owner = THIS_MODULE,
-+ .of_match_table = bcm2835_smi_dev_of_match,
-+ },
-+};
-+
-+module_platform_driver(bcm2835_smi_dev_driver);
-+
-+MODULE_ALIAS("platform:smi-dev-bcm2835");
-+MODULE_LICENSE("GPL");
-+MODULE_DESCRIPTION(
-+ "Character device driver for BCM2835's secondary memory interface");
-+MODULE_AUTHOR("Luke Wren <luke at raspberrypi.org>");
---- a/drivers/misc/Kconfig
-+++ b/drivers/misc/Kconfig
-@@ -10,6 +10,14 @@ config SENSORS_LIS3LV02D
- select INPUT_POLLDEV
- default n
-
-+config BCM2835_SMI
-+ tristate "Broadcom 283x Secondary Memory Interface driver"
-+ depends on MACH_BCM2708 || MACH_BCM2709 || ARCH_BCM2835
-+ default m
-+ help
-+ Driver for enabling and using Broadcom's Secondary/Slow Memory Interface.
-+ Appears as /dev/bcm2835_smi. For ioctl interface see drivers/misc/bcm2835_smi.h
-+
- config AD525X_DPOT
- tristate "Analog Devices Digital Potentiometers"
- depends on (I2C || SPI) && SYSFS
---- a/drivers/misc/Makefile
-+++ b/drivers/misc/Makefile
-@@ -9,6 +9,7 @@ obj-$(CONFIG_AD525X_DPOT_SPI) += ad525x_
- obj-$(CONFIG_INTEL_MID_PTI) += pti.o
- obj-$(CONFIG_ATMEL_SSC) += atmel-ssc.o
- obj-$(CONFIG_ATMEL_TCLIB) += atmel_tclib.o
-+obj-$(CONFIG_BCM2835_SMI) += bcm2835_smi.o
- obj-$(CONFIG_BMP085) += bmp085.o
- obj-$(CONFIG_BMP085_I2C) += bmp085-i2c.o
- obj-$(CONFIG_BMP085_SPI) += bmp085-spi.o
---- /dev/null
-+++ b/drivers/misc/bcm2835_smi.c
-@@ -0,0 +1,985 @@
-+/**
-+ * Broadcom Secondary Memory Interface driver
-+ *
-+ * Written by Luke Wren <luke at raspberrypi.org>
-+ * Copyright (c) 2015, Raspberry Pi (Trading) Ltd.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+#include <linux/of.h>
-+#include <linux/platform_device.h>
-+#include <linux/of_address.h>
-+#include <linux/of_platform.h>
-+#include <linux/mm.h>
-+#include <linux/slab.h>
-+#include <linux/pagemap.h>
-+#include <linux/dma-mapping.h>
-+#include <linux/dmaengine.h>
-+#include <linux/semaphore.h>
-+#include <linux/spinlock.h>
-+#include <linux/io.h>
-+
-+#define BCM2835_SMI_IMPLEMENTATION
-+#include <linux/broadcom/bcm2835_smi.h>
-+
-+#define DRIVER_NAME "smi-bcm2835"
-+
-+#define N_PAGES_FROM_BYTES(n) ((n + PAGE_SIZE-1) / PAGE_SIZE)
-+
-+#define DMA_WRITE_TO_MEM true
-+#define DMA_READ_FROM_MEM false
-+
-+struct bcm2835_smi_instance {
-+ struct device *dev;
-+ struct smi_settings settings;
-+ __iomem void *smi_regs_ptr, *cm_smi_regs_ptr;
-+ dma_addr_t smi_regs_busaddr;
-+
-+ struct dma_chan *dma_chan;
-+ struct dma_slave_config dma_config;
-+
-+ struct bcm2835_smi_bounce_info bounce;
-+
-+ struct scatterlist buffer_sgl;
-+
-+ int clock_source;
-+ int clock_divisor;
-+
-+ /* Sometimes we are called into in an atomic context (e.g. by
-+ JFFS2 + MTD) so we can't use a mutex */
-+ spinlock_t transaction_lock;
-+};
-+
-+/****************************************************************************
-+*
-+* SMI clock manager setup
-+*
-+***************************************************************************/
-+
-+static inline void write_smi_cm_reg(struct bcm2835_smi_instance *inst,
-+ u32 val, unsigned reg)
-+{
-+ writel(CM_PWD | val, inst->cm_smi_regs_ptr + reg);
-+}
-+
-+static inline u32 read_smi_cm_reg(struct bcm2835_smi_instance *inst,
-+ unsigned reg)
-+{
-+ return readl(inst->cm_smi_regs_ptr + reg);
-+}
-+
-+static void smi_setup_clock(struct bcm2835_smi_instance *inst)
-+{
-+ dev_dbg(inst->dev, "Setting up clock...");
-+ /* Disable SMI clock and wait for it to stop. */
-+ write_smi_cm_reg(inst, 0, CM_SMI_CTL);
-+ while (read_smi_cm_reg(inst, CM_SMI_CTL) & CM_SMI_CTL_BUSY)
-+ ;
-+
-+ write_smi_cm_reg(inst, (inst->clock_divisor << CM_SMI_DIV_DIVI_OFFS),
-+ CM_SMI_DIV);
-+ write_smi_cm_reg(inst, (inst->clock_source << CM_SMI_CTL_SRC_OFFS),
-+ CM_SMI_CTL);
-+
-+ /* Enable the clock */
-+ write_smi_cm_reg(inst, (inst->clock_source << CM_SMI_CTL_SRC_OFFS) |
-+ CM_SMI_CTL_ENAB, CM_SMI_CTL);
-+}
-+
-+/****************************************************************************
-+*
-+* SMI peripheral setup
-+*
-+***************************************************************************/
-+
-+static inline void write_smi_reg(struct bcm2835_smi_instance *inst,
-+ u32 val, unsigned reg)
-+{
-+ writel(val, inst->smi_regs_ptr + reg);
-+}
-+
-+static inline u32 read_smi_reg(struct bcm2835_smi_instance *inst, unsigned reg)
-+{
-+ return readl(inst->smi_regs_ptr + reg);
-+}
-+
-+/* Token-paste macro for e.g SMIDSR_RSTROBE -> value of SMIDSR_RSTROBE_MASK */
-+#define _CONCAT(x, y) x##y
-+#define CONCAT(x, y) _CONCAT(x, y)
-+
-+#define SET_BIT_FIELD(dest, field, bits) ((dest) = \
-+ ((dest) & ~CONCAT(field, _MASK)) | (((bits) << CONCAT(field, _OFFS))& \
-+ CONCAT(field, _MASK)))
-+#define GET_BIT_FIELD(src, field) (((src) & \
-+ CONCAT(field, _MASK)) >> CONCAT(field, _OFFS))
-+
-+static void smi_dump_context_labelled(struct bcm2835_smi_instance *inst,
-+ const char *label)
-+{
-+ dev_err(inst->dev, "SMI context dump: %s", label);
-+ dev_err(inst->dev, "SMICS: 0x%08x", read_smi_reg(inst, SMICS));
-+ dev_err(inst->dev, "SMIL: 0x%08x", read_smi_reg(inst, SMIL));
-+ dev_err(inst->dev, "SMIDSR: 0x%08x", read_smi_reg(inst, SMIDSR0));
-+ dev_err(inst->dev, "SMIDSW: 0x%08x", read_smi_reg(inst, SMIDSW0));
-+ dev_err(inst->dev, "SMIDC: 0x%08x", read_smi_reg(inst, SMIDC));
-+ dev_err(inst->dev, "SMIFD: 0x%08x", read_smi_reg(inst, SMIFD));
-+ dev_err(inst->dev, " ");
-+}
-+
-+static inline void smi_dump_context(struct bcm2835_smi_instance *inst)
-+{
-+ smi_dump_context_labelled(inst, "");
-+}
-+
-+static void smi_get_default_settings(struct bcm2835_smi_instance *inst)
-+{
-+ struct smi_settings *settings = &inst->settings;
-+
-+ settings->data_width = SMI_WIDTH_16BIT;
-+ settings->pack_data = true;
-+
-+ settings->read_setup_time = 1;
-+ settings->read_hold_time = 1;
-+ settings->read_pace_time = 1;
-+ settings->read_strobe_time = 3;
-+
-+ settings->write_setup_time = settings->read_setup_time;
-+ settings->write_hold_time = settings->read_hold_time;
-+ settings->write_pace_time = settings->read_pace_time;
-+ settings->write_strobe_time = settings->read_strobe_time;
-+
-+ settings->dma_enable = true;
-+ settings->dma_passthrough_enable = false;
-+ settings->dma_read_thresh = 0x01;
-+ settings->dma_write_thresh = 0x3f;
-+ settings->dma_panic_read_thresh = 0x20;
-+ settings->dma_panic_write_thresh = 0x20;
-+}
-+
-+void bcm2835_smi_set_regs_from_settings(struct bcm2835_smi_instance *inst)
-+{
-+ struct smi_settings *settings = &inst->settings;
-+ int smidsr_temp = 0, smidsw_temp = 0, smics_temp,
-+ smidcs_temp, smidc_temp = 0;
-+
-+ spin_lock(&inst->transaction_lock);
-+
-+ /* temporarily disable the peripheral: */
-+ smics_temp = read_smi_reg(inst, SMICS);
-+ write_smi_reg(inst, 0, SMICS);
-+ smidcs_temp = read_smi_reg(inst, SMIDCS);
-+ write_smi_reg(inst, 0, SMIDCS);
-+
-+ if (settings->pack_data)
-+ smics_temp |= SMICS_PXLDAT;
-+ else
-+ smics_temp &= ~SMICS_PXLDAT;
-+
-+ SET_BIT_FIELD(smidsr_temp, SMIDSR_RWIDTH, settings->data_width);
-+ SET_BIT_FIELD(smidsr_temp, SMIDSR_RSETUP, settings->read_setup_time);
-+ SET_BIT_FIELD(smidsr_temp, SMIDSR_RHOLD, settings->read_hold_time);
-+ SET_BIT_FIELD(smidsr_temp, SMIDSR_RPACE, settings->read_pace_time);
-+ SET_BIT_FIELD(smidsr_temp, SMIDSR_RSTROBE, settings->read_strobe_time);
-+ write_smi_reg(inst, smidsr_temp, SMIDSR0);
-+
-+ SET_BIT_FIELD(smidsw_temp, SMIDSW_WWIDTH, settings->data_width);
-+ if (settings->data_width == SMI_WIDTH_8BIT)
-+ smidsw_temp |= SMIDSW_WSWAP;
-+ else
-+ smidsw_temp &= ~SMIDSW_WSWAP;
-+ SET_BIT_FIELD(smidsw_temp, SMIDSW_WSETUP, settings->write_setup_time);
-+ SET_BIT_FIELD(smidsw_temp, SMIDSW_WHOLD, settings->write_hold_time);
-+ SET_BIT_FIELD(smidsw_temp, SMIDSW_WPACE, settings->write_pace_time);
-+ SET_BIT_FIELD(smidsw_temp, SMIDSW_WSTROBE,
-+ settings->write_strobe_time);
-+ write_smi_reg(inst, smidsw_temp, SMIDSW0);
-+
-+ SET_BIT_FIELD(smidc_temp, SMIDC_REQR, settings->dma_read_thresh);
-+ SET_BIT_FIELD(smidc_temp, SMIDC_REQW, settings->dma_write_thresh);
-+ SET_BIT_FIELD(smidc_temp, SMIDC_PANICR,
-+ settings->dma_panic_read_thresh);
-+ SET_BIT_FIELD(smidc_temp, SMIDC_PANICW,
-+ settings->dma_panic_write_thresh);
-+ if (settings->dma_passthrough_enable) {
-+ smidc_temp |= SMIDC_DMAP;
-+ smidsr_temp |= SMIDSR_RDREQ;
-+ write_smi_reg(inst, smidsr_temp, SMIDSR0);
-+ smidsw_temp |= SMIDSW_WDREQ;
-+ write_smi_reg(inst, smidsw_temp, SMIDSW0);
-+ } else
-+ smidc_temp &= ~SMIDC_DMAP;
-+ if (settings->dma_enable)
-+ smidc_temp |= SMIDC_DMAEN;
-+ else
-+ smidc_temp &= ~SMIDC_DMAEN;
-+
-+ write_smi_reg(inst, smidc_temp, SMIDC);
-+
-+ /* re-enable (if was previously enabled) */
-+ write_smi_reg(inst, smics_temp, SMICS);
-+ write_smi_reg(inst, smidcs_temp, SMIDCS);
-+
-+ spin_unlock(&inst->transaction_lock);
-+}
-+EXPORT_SYMBOL(bcm2835_smi_set_regs_from_settings);
-+
-+struct smi_settings *bcm2835_smi_get_settings_from_regs
-+ (struct bcm2835_smi_instance *inst)
-+{
-+ struct smi_settings *settings = &inst->settings;
-+ int smidsr, smidsw, smidc;
-+
-+ spin_lock(&inst->transaction_lock);
-+
-+ smidsr = read_smi_reg(inst, SMIDSR0);
-+ smidsw = read_smi_reg(inst, SMIDSW0);
-+ smidc = read_smi_reg(inst, SMIDC);
-+
-+ settings->pack_data = (read_smi_reg(inst, SMICS) & SMICS_PXLDAT) ?
-+ true : false;
-+
-+ settings->data_width = GET_BIT_FIELD(smidsr, SMIDSR_RWIDTH);
-+ settings->read_setup_time = GET_BIT_FIELD(smidsr, SMIDSR_RSETUP);
-+ settings->read_hold_time = GET_BIT_FIELD(smidsr, SMIDSR_RHOLD);
-+ settings->read_pace_time = GET_BIT_FIELD(smidsr, SMIDSR_RPACE);
-+ settings->read_strobe_time = GET_BIT_FIELD(smidsr, SMIDSR_RSTROBE);
-+
-+ settings->write_setup_time = GET_BIT_FIELD(smidsw, SMIDSW_WSETUP);
-+ settings->write_hold_time = GET_BIT_FIELD(smidsw, SMIDSW_WHOLD);
-+ settings->write_pace_time = GET_BIT_FIELD(smidsw, SMIDSW_WPACE);
-+ settings->write_strobe_time = GET_BIT_FIELD(smidsw, SMIDSW_WSTROBE);
-+
-+ settings->dma_read_thresh = GET_BIT_FIELD(smidc, SMIDC_REQR);
-+ settings->dma_write_thresh = GET_BIT_FIELD(smidc, SMIDC_REQW);
-+ settings->dma_panic_read_thresh = GET_BIT_FIELD(smidc, SMIDC_PANICR);
-+ settings->dma_panic_write_thresh = GET_BIT_FIELD(smidc, SMIDC_PANICW);
-+ settings->dma_passthrough_enable = (smidc & SMIDC_DMAP) ? true : false;
-+ settings->dma_enable = (smidc & SMIDC_DMAEN) ? true : false;
-+
-+ spin_unlock(&inst->transaction_lock);
-+
-+ return settings;
-+}
-+EXPORT_SYMBOL(bcm2835_smi_get_settings_from_regs);
-+
-+static inline void smi_set_address(struct bcm2835_smi_instance *inst,
-+ unsigned int address)
-+{
-+ int smia_temp = 0, smida_temp = 0;
-+
-+ SET_BIT_FIELD(smia_temp, SMIA_ADDR, address);
-+ SET_BIT_FIELD(smida_temp, SMIDA_ADDR, address);
-+
-+ /* Write to both address registers - user doesn't care whether we're
-+ doing programmed or direct transfers. */
-+ write_smi_reg(inst, smia_temp, SMIA);
-+ write_smi_reg(inst, smida_temp, SMIDA);
-+}
-+
-+static void smi_setup_regs(struct bcm2835_smi_instance *inst)
-+{
-+
-+ dev_dbg(inst->dev, "Initialising SMI registers...");
-+ /* Disable the peripheral if already enabled */
-+ write_smi_reg(inst, 0, SMICS);
-+ write_smi_reg(inst, 0, SMIDCS);
-+
-+ smi_get_default_settings(inst);
-+ bcm2835_smi_set_regs_from_settings(inst);
-+ smi_set_address(inst, 0);
-+
-+ write_smi_reg(inst, read_smi_reg(inst, SMICS) | SMICS_ENABLE, SMICS);
-+ write_smi_reg(inst, read_smi_reg(inst, SMIDCS) | SMIDCS_ENABLE,
-+ SMIDCS);
-+}
-+
-+/****************************************************************************
-+*
-+* Low-level SMI access functions
-+* Other modules should use the exported higher-level functions e.g.
-+* bcm2835_smi_write_buf() unless they have a good reason to use these
-+*
-+***************************************************************************/
-+
-+static inline uint32_t smi_read_single_word(struct bcm2835_smi_instance *inst)
-+{
-+ int timeout = 0;
-+
-+ write_smi_reg(inst, SMIDCS_ENABLE, SMIDCS);
-+ write_smi_reg(inst, SMIDCS_ENABLE | SMIDCS_START, SMIDCS);
-+ /* Make sure things happen in the right order...*/
-+ mb();
-+ while (!(read_smi_reg(inst, SMIDCS) & SMIDCS_DONE) &&
-+ ++timeout < 10000)
-+ ;
-+ if (timeout < 10000)
-+ return read_smi_reg(inst, SMIDD);
-+
-+ dev_err(inst->dev,
-+ "SMI direct read timed out (is the clock set up correctly?)");
-+ return 0;
-+}
-+
-+static inline void smi_write_single_word(struct bcm2835_smi_instance *inst,
-+ uint32_t data)
-+{
-+ int timeout = 0;
-+
-+ write_smi_reg(inst, SMIDCS_ENABLE | SMIDCS_WRITE, SMIDCS);
-+ write_smi_reg(inst, data, SMIDD);
-+ write_smi_reg(inst, SMIDCS_ENABLE | SMIDCS_WRITE | SMIDCS_START,
-+ SMIDCS);
-+
-+ while (!(read_smi_reg(inst, SMIDCS) & SMIDCS_DONE) &&
-+ ++timeout < 10000)
-+ ;
-+ if (timeout >= 10000)
-+ dev_err(inst->dev,
-+ "SMI direct write timed out (is the clock set up correctly?)");
-+}
-+
-+/* Initiates a programmed read into the read FIFO. It is up to the caller to
-+ * read data from the FIFO - either via paced DMA transfer,
-+ * or polling SMICS_RXD to check whether data is available.
-+ * SMICS_ACTIVE will go low upon completion. */
-+static void smi_init_programmed_read(struct bcm2835_smi_instance *inst,
-+ int num_transfers)
-+{
-+ int smics_temp;
-+
-+ /* Disable the peripheral: */
-+ smics_temp = read_smi_reg(inst, SMICS) & ~(SMICS_ENABLE | SMICS_WRITE);
-+ write_smi_reg(inst, smics_temp, SMICS);
-+ while (read_smi_reg(inst, SMICS) & SMICS_ENABLE)
-+ ;
-+
-+ /* Program the transfer count: */
-+ write_smi_reg(inst, num_transfers, SMIL);
-+
-+ /* re-enable and start: */
-+ smics_temp |= SMICS_ENABLE;
-+ write_smi_reg(inst, smics_temp, SMICS);
-+ smics_temp |= SMICS_CLEAR;
-+ /* Just to be certain: */
-+ mb();
-+ while (read_smi_reg(inst, SMICS) & SMICS_ACTIVE)
-+ ;
-+ write_smi_reg(inst, smics_temp, SMICS);
-+ smics_temp |= SMICS_START;
-+ write_smi_reg(inst, smics_temp, SMICS);
-+}
-+
-+/* Initiates a programmed write sequence, using data from the write FIFO.
-+ * It is up to the caller to initiate a DMA transfer before calling,
-+ * or use another method to keep the write FIFO topped up.
-+ * SMICS_ACTIVE will go low upon completion.
-+ */
-+static void smi_init_programmed_write(struct bcm2835_smi_instance *inst,
-+ int num_transfers)
-+{
-+ int smics_temp;
-+
-+ /* Disable the peripheral: */
-+ smics_temp = read_smi_reg(inst, SMICS) & ~SMICS_ENABLE;
-+ write_smi_reg(inst, smics_temp, SMICS);
-+ while (read_smi_reg(inst, SMICS) & SMICS_ENABLE)
-+ ;
-+
-+ /* Program the transfer count: */
-+ write_smi_reg(inst, num_transfers, SMIL);
-+
-+ /* setup, re-enable and start: */
-+ smics_temp |= SMICS_WRITE | SMICS_ENABLE;
-+ write_smi_reg(inst, smics_temp, SMICS);
-+ smics_temp |= SMICS_START;
-+ write_smi_reg(inst, smics_temp, SMICS);
-+}
-+
-+/* Initiate a read and then poll FIFO for data, reading out as it appears. */
-+static void smi_read_fifo(struct bcm2835_smi_instance *inst,
-+ uint32_t *dest, int n_bytes)
-+{
-+ if (read_smi_reg(inst, SMICS) & SMICS_RXD) {
-+ smi_dump_context_labelled(inst,
-+ "WARNING: read FIFO not empty at start of read call.");
-+ while (read_smi_reg(inst, SMICS))
-+ ;
-+ }
-+
-+ /* Dispatch the read: */
-+ if (inst->settings.data_width == SMI_WIDTH_8BIT)
-+ smi_init_programmed_read(inst, n_bytes);
-+ else if (inst->settings.data_width == SMI_WIDTH_16BIT)
-+ smi_init_programmed_read(inst, n_bytes / 2);
-+ else {
-+ dev_err(inst->dev, "Unsupported data width for read.");
-+ return;
-+ }
-+
-+ /* Poll FIFO to keep it empty */
-+ while (!(read_smi_reg(inst, SMICS) & SMICS_DONE))
-+ if (read_smi_reg(inst, SMICS) & SMICS_RXD)
-+ *dest++ = read_smi_reg(inst, SMID);
-+
-+ /* Ensure that the FIFO is emptied */
-+ if (read_smi_reg(inst, SMICS) & SMICS_RXD) {
-+ int fifo_count;
-+
-+ fifo_count = GET_BIT_FIELD(read_smi_reg(inst, SMIFD),
-+ SMIFD_FCNT);
-+ while (fifo_count--)
-+ *dest++ = read_smi_reg(inst, SMID);
-+ }
-+
-+ if (!(read_smi_reg(inst, SMICS) & SMICS_DONE))
-+ smi_dump_context_labelled(inst,
-+ "WARNING: transaction finished but done bit not set.");
-+
-+ if (read_smi_reg(inst, SMICS) & SMICS_RXD)
-+ smi_dump_context_labelled(inst,
-+ "WARNING: read FIFO not empty at end of read call.");
-+
-+}
-+
-+/* Initiate a write, and then keep the FIFO topped up. */
-+static void smi_write_fifo(struct bcm2835_smi_instance *inst,
-+ uint32_t *src, int n_bytes)
-+{
-+ int i, timeout = 0;
-+
-+ /* Empty FIFOs if not already so */
-+ if (!(read_smi_reg(inst, SMICS) & SMICS_TXE)) {
-+ smi_dump_context_labelled(inst,
-+ "WARNING: write fifo not empty at start of write call.");
-+ write_smi_reg(inst, read_smi_reg(inst, SMICS) | SMICS_CLEAR,
-+ SMICS);
-+ }
-+
-+ /* Initiate the transfer */
-+ if (inst->settings.data_width == SMI_WIDTH_8BIT)
-+ smi_init_programmed_write(inst, n_bytes);
-+ else if (inst->settings.data_width == SMI_WIDTH_16BIT)
-+ smi_init_programmed_write(inst, n_bytes / 2);
-+ else {
-+ dev_err(inst->dev, "Unsupported data width for write.");
-+ return;
-+ }
-+ /* Fill the FIFO: */
-+ for (i = 0; i < (n_bytes - 1) / 4 + 1; ++i) {
-+ while (!(read_smi_reg(inst, SMICS) & SMICS_TXD))
-+ ;
-+ write_smi_reg(inst, *src++, SMID);
-+ }
-+ /* Busy wait... */
-+ while (!(read_smi_reg(inst, SMICS) & SMICS_DONE) && ++timeout <
-+ 1000000)
-+ ;
-+ if (timeout >= 1000000)
-+ smi_dump_context_labelled(inst,
-+ "Timed out on write operation!");
-+ if (!(read_smi_reg(inst, SMICS) & SMICS_TXE))
-+ smi_dump_context_labelled(inst,
-+ "WARNING: FIFO not empty at end of write operation.");
-+}
-+
-+/****************************************************************************
-+*
-+* SMI DMA operations
-+*
-+***************************************************************************/
-+
-+/* Disable SMI and put it into the correct direction before doing DMA setup.
-+ Stops spurious DREQs during setup. Peripheral is re-enabled by init_*() */
-+static void smi_disable(struct bcm2835_smi_instance *inst,
-+ enum dma_transfer_direction direction)
-+{
-+ int smics_temp = read_smi_reg(inst, SMICS) & ~SMICS_ENABLE;
-+
-+ if (direction == DMA_DEV_TO_MEM)
-+ smics_temp &= ~SMICS_WRITE;
-+ else
-+ smics_temp |= SMICS_WRITE;
-+ write_smi_reg(inst, smics_temp, SMICS);
-+ while (read_smi_reg(inst, SMICS) & SMICS_ACTIVE)
-+ ;
-+}
-+
-+static struct scatterlist *smi_scatterlist_from_buffer(
-+ struct bcm2835_smi_instance *inst,
-+ dma_addr_t buf,
-+ size_t len,
-+ struct scatterlist *sg)
-+{
-+ sg_init_table(sg, 1);
-+ sg_dma_address(sg) = buf;
-+ sg_dma_len(sg) = len;
-+ return sg;
-+}
-+
-+static void smi_dma_callback_user_copy(void *param)
-+{
-+ /* Notify the bottom half that a chunk is ready for user copy */
-+ struct bcm2835_smi_instance *inst =
-+ (struct bcm2835_smi_instance *)param;
-+
-+ up(&inst->bounce.callback_sem);
-+}
-+
-+/* Creates a descriptor, assigns the given callback, and submits the
-+ descriptor to dmaengine. Does not block - can queue up multiple
-+ descriptors and then wait for them all to complete.
-+ sg_len is the number of control blocks, NOT the number of bytes.
-+ dir can be DMA_MEM_TO_DEV or DMA_DEV_TO_MEM.
-+ callback can be NULL - in this case it is not called. */
-+static inline struct dma_async_tx_descriptor *smi_dma_submit_sgl(
-+ struct bcm2835_smi_instance *inst,
-+ struct scatterlist *sgl,
-+ size_t sg_len,
-+ enum dma_transfer_direction dir,
-+ dma_async_tx_callback callback)
-+{
-+ struct dma_async_tx_descriptor *desc;
-+
-+ desc = dmaengine_prep_slave_sg(inst->dma_chan,
-+ sgl,
-+ sg_len,
-+ dir,
-+ DMA_PREP_INTERRUPT | DMA_CTRL_ACK |
-+ DMA_PREP_FENCE);
-+ if (!desc) {
-+ dev_err(inst->dev, "read_sgl: dma slave preparation failed!");
-+ write_smi_reg(inst, read_smi_reg(inst, SMICS) & ~SMICS_ACTIVE,
-+ SMICS);
-+ while (read_smi_reg(inst, SMICS) & SMICS_ACTIVE)
-+ cpu_relax();
-+ write_smi_reg(inst, read_smi_reg(inst, SMICS) | SMICS_ACTIVE,
-+ SMICS);
-+ return NULL;
-+ }
-+ desc->callback = callback;
-+ desc->callback_param = inst;
-+ if (dmaengine_submit(desc) < 0)
-+ return NULL;
-+ return desc;
-+}
-+
-+/* NB this function blocks until the transfer is complete */
-+static void
-+smi_dma_read_sgl(struct bcm2835_smi_instance *inst,
-+ struct scatterlist *sgl, size_t sg_len, size_t n_bytes)
-+{
-+ struct dma_async_tx_descriptor *desc;
-+
-+ /* Disable SMI and set to read before dispatching DMA - if SMI is in
-+ * write mode and TX fifo is empty, it will generate a DREQ which may
-+ * cause the read DMA to complete before the SMI read command is even
-+ * dispatched! We want to dispatch DMA before SMI read so that reading
-+ * is gapless, for logic analyser.
-+ */
-+
-+ smi_disable(inst, DMA_DEV_TO_MEM);
-+
-+ desc = smi_dma_submit_sgl(inst, sgl, sg_len, DMA_DEV_TO_MEM, NULL);
-+ dma_async_issue_pending(inst->dma_chan);
-+
-+ if (inst->settings.data_width == SMI_WIDTH_8BIT)
-+ smi_init_programmed_read(inst, n_bytes);
-+ else
-+ smi_init_programmed_read(inst, n_bytes / 2);
-+
-+ if (dma_wait_for_async_tx(desc) == DMA_ERROR)
-+ smi_dump_context_labelled(inst, "DMA timeout!");
-+}
-+
-+static void
-+smi_dma_write_sgl(struct bcm2835_smi_instance *inst,
-+ struct scatterlist *sgl, size_t sg_len, size_t n_bytes)
-+{
-+ struct dma_async_tx_descriptor *desc;
-+
-+ if (inst->settings.data_width == SMI_WIDTH_8BIT)
-+ smi_init_programmed_write(inst, n_bytes);
-+ else
-+ smi_init_programmed_write(inst, n_bytes / 2);
-+
-+ desc = smi_dma_submit_sgl(inst, sgl, sg_len, DMA_MEM_TO_DEV, NULL);
-+ dma_async_issue_pending(inst->dma_chan);
-+
-+ if (dma_wait_for_async_tx(desc) == DMA_ERROR)
-+ smi_dump_context_labelled(inst, "DMA timeout!");
-+ else
-+ /* Wait for SMI to finish our writes */
-+ while (!(read_smi_reg(inst, SMICS) & SMICS_DONE))
-+ cpu_relax();
-+}
-+
-+ssize_t bcm2835_smi_user_dma(
-+ struct bcm2835_smi_instance *inst,
-+ enum dma_transfer_direction dma_dir,
-+ char __user *user_ptr, size_t count,
-+ struct bcm2835_smi_bounce_info **bounce)
-+{
-+ int chunk_no = 0, chunk_size, count_left = count;
-+ struct scatterlist *sgl;
-+ void (*init_trans_func)(struct bcm2835_smi_instance *, int);
-+
-+ spin_lock(&inst->transaction_lock);
-+
-+ if (dma_dir == DMA_DEV_TO_MEM)
-+ init_trans_func = smi_init_programmed_read;
-+ else
-+ init_trans_func = smi_init_programmed_write;
-+
-+ smi_disable(inst, dma_dir);
-+
-+ sema_init(&inst->bounce.callback_sem, 0);
-+ if (bounce)
-+ *bounce = &inst->bounce;
-+ while (count_left) {
-+ chunk_size = count_left > DMA_BOUNCE_BUFFER_SIZE ?
-+ DMA_BOUNCE_BUFFER_SIZE : count_left;
-+ if (chunk_size == DMA_BOUNCE_BUFFER_SIZE) {
-+ sgl =
-+ &inst->bounce.sgl[chunk_no % DMA_BOUNCE_BUFFER_COUNT];
-+ } else {
-+ sgl = smi_scatterlist_from_buffer(
-+ inst,
-+ inst->bounce.phys[
-+ chunk_no % DMA_BOUNCE_BUFFER_COUNT],
-+ chunk_size,
-+ &inst->buffer_sgl);
-+ }
-+
-+ if (!smi_dma_submit_sgl(inst, sgl, 1, dma_dir,
-+ smi_dma_callback_user_copy
-+ )) {
-+ dev_err(inst->dev, "sgl submit failed");
-+ count = 0;
-+ goto out;
-+ }
-+ count_left -= chunk_size;
-+ chunk_no++;
-+ }
-+ dma_async_issue_pending(inst->dma_chan);
-+
-+ if (inst->settings.data_width == SMI_WIDTH_8BIT)
-+ init_trans_func(inst, count);
-+ else if (inst->settings.data_width == SMI_WIDTH_16BIT)
-+ init_trans_func(inst, count / 2);
-+out:
-+ spin_unlock(&inst->transaction_lock);
-+ return count;
-+}
-+EXPORT_SYMBOL(bcm2835_smi_user_dma);
-+
-+
-+/****************************************************************************
-+*
-+* High level buffer transfer functions - for use by other drivers
-+*
-+***************************************************************************/
-+
-+/* Buffer must be physically contiguous - i.e. kmalloc, not vmalloc! */
-+void bcm2835_smi_write_buf(
-+ struct bcm2835_smi_instance *inst,
-+ const void *buf, size_t n_bytes)
-+{
-+ int odd_bytes = n_bytes & 0x3;
-+
-+ n_bytes -= odd_bytes;
-+
-+ spin_lock(&inst->transaction_lock);
-+
-+ if (n_bytes > DMA_THRESHOLD_BYTES) {
-+ dma_addr_t phy_addr = dma_map_single(
-+ inst->dev,
-+ (void *)buf,
-+ n_bytes,
-+ DMA_MEM_TO_DEV);
-+ struct scatterlist *sgl =
-+ smi_scatterlist_from_buffer(inst, phy_addr, n_bytes,
-+ &inst->buffer_sgl);
-+
-+ if (!sgl) {
-+ smi_dump_context_labelled(inst,
-+ "Error: could not create scatterlist for write!");
-+ goto out;
-+ }
-+ smi_dma_write_sgl(inst, sgl, 1, n_bytes);
-+
-+ dma_unmap_single
-+ (inst->dev, phy_addr, n_bytes, DMA_MEM_TO_DEV);
-+ } else if (n_bytes) {
-+ smi_write_fifo(inst, (uint32_t *) buf, n_bytes);
-+ }
-+ buf += n_bytes;
-+
-+ if (inst->settings.data_width == SMI_WIDTH_8BIT) {
-+ while (odd_bytes--)
-+ smi_write_single_word(inst, *(uint8_t *) (buf++));
-+ } else {
-+ while (odd_bytes >= 2) {
-+ smi_write_single_word(inst, *(uint16_t *)buf);
-+ buf += 2;
-+ odd_bytes -= 2;
-+ }
-+ if (odd_bytes) {
-+ /* Reading an odd number of bytes on a 16 bit bus is
-+ a user bug. It's kinder to fail early and tell them
-+ than to e.g. transparently give them the bottom byte
-+ of a 16 bit transfer. */
-+ dev_err(inst->dev,
-+ "WARNING: odd number of bytes specified for wide transfer.");
-+ dev_err(inst->dev,
-+ "At least one byte dropped as a result.");
-+ dump_stack();
-+ }
-+ }
-+out:
-+ spin_unlock(&inst->transaction_lock);
-+}
-+EXPORT_SYMBOL(bcm2835_smi_write_buf);
-+
-+void bcm2835_smi_read_buf(struct bcm2835_smi_instance *inst,
-+ void *buf, size_t n_bytes)
-+{
-+
-+ /* SMI is inherently 32-bit, which causes surprising amounts of mess
-+ for bytes % 4 != 0. Easiest to avoid this mess altogether
-+ by handling remainder separately. */
-+ int odd_bytes = n_bytes & 0x3;
-+
-+ spin_lock(&inst->transaction_lock);
-+ n_bytes -= odd_bytes;
-+ if (n_bytes > DMA_THRESHOLD_BYTES) {
-+ dma_addr_t phy_addr = dma_map_single(inst->dev,
-+ buf, n_bytes,
-+ DMA_DEV_TO_MEM);
-+ struct scatterlist *sgl = smi_scatterlist_from_buffer(
-+ inst, phy_addr, n_bytes,
-+ &inst->buffer_sgl);
-+ if (!sgl) {
-+ smi_dump_context_labelled(inst,
-+ "Error: could not create scatterlist for read!");
-+ goto out;
-+ }
-+ smi_dma_read_sgl(inst, sgl, 1, n_bytes);
-+ dma_unmap_single(inst->dev, phy_addr, n_bytes, DMA_DEV_TO_MEM);
-+ } else if (n_bytes) {
-+ smi_read_fifo(inst, (uint32_t *)buf, n_bytes);
-+ }
-+ buf += n_bytes;
-+
-+ if (inst->settings.data_width == SMI_WIDTH_8BIT) {
-+ while (odd_bytes--)
-+ *((uint8_t *) (buf++)) = smi_read_single_word(inst);
-+ } else {
-+ while (odd_bytes >= 2) {
-+ *(uint16_t *) buf = smi_read_single_word(inst);
-+ buf += 2;
-+ odd_bytes -= 2;
-+ }
-+ if (odd_bytes) {
-+ dev_err(inst->dev,
-+ "WARNING: odd number of bytes specified for wide transfer.");
-+ dev_err(inst->dev,
-+ "At least one byte dropped as a result.");
-+ dump_stack();
-+ }
-+ }
-+out:
-+ spin_unlock(&inst->transaction_lock);
-+}
-+EXPORT_SYMBOL(bcm2835_smi_read_buf);
-+
-+void bcm2835_smi_set_address(struct bcm2835_smi_instance *inst,
-+ unsigned int address)
-+{
-+ spin_lock(&inst->transaction_lock);
-+ smi_set_address(inst, address);
-+ spin_unlock(&inst->transaction_lock);
-+}
-+EXPORT_SYMBOL(bcm2835_smi_set_address);
-+
-+struct bcm2835_smi_instance *bcm2835_smi_get(struct device_node *node)
-+{
-+ struct platform_device *pdev;
-+
-+ if (!node)
-+ return NULL;
-+
-+ pdev = of_find_device_by_node(node);
-+ if (!pdev)
-+ return NULL;
-+
-+ return platform_get_drvdata(pdev);
-+}
-+EXPORT_SYMBOL(bcm2835_smi_get);
-+
-+/****************************************************************************
-+*
-+* bcm2835_smi_probe - called when the driver is loaded.
-+*
-+***************************************************************************/
-+
-+static int bcm2835_smi_dma_setup(struct bcm2835_smi_instance *inst)
-+{
-+ int i, rv = 0;
-+
-+ inst->dma_chan = dma_request_slave_channel(inst->dev, "rx-tx");
-+
-+ inst->dma_config.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
-+ inst->dma_config.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
-+ inst->dma_config.src_addr = inst->smi_regs_busaddr + SMID;
-+ inst->dma_config.dst_addr = inst->dma_config.src_addr;
-+ /* Direction unimportant - always overridden by prep_slave_sg */
-+ inst->dma_config.direction = DMA_DEV_TO_MEM;
-+ dmaengine_slave_config(inst->dma_chan, &inst->dma_config);
-+ /* Alloc and map bounce buffers */
-+ for (i = 0; i < DMA_BOUNCE_BUFFER_COUNT; ++i) {
-+ inst->bounce.buffer[i] =
-+ dmam_alloc_coherent(inst->dev, DMA_BOUNCE_BUFFER_SIZE,
-+ &inst->bounce.phys[i],
-+ GFP_KERNEL);
-+ if (!inst->bounce.buffer[i]) {
-+ dev_err(inst->dev, "Could not allocate buffer!");
-+ rv = -ENOMEM;
-+ break;
-+ }
-+ smi_scatterlist_from_buffer(
-+ inst,
-+ inst->bounce.phys[i],
-+ DMA_BOUNCE_BUFFER_SIZE,
-+ &inst->bounce.sgl[i]
-+ );
-+ }
-+
-+ return rv;
-+}
-+
-+static int bcm2835_smi_probe(struct platform_device *pdev)
-+{
-+ int err;
-+ struct device *dev = &pdev->dev;
-+ struct device_node *node = dev->of_node;
-+ struct resource *ioresource;
-+ struct bcm2835_smi_instance *inst;
-+
-+ /* Allocate buffers and instance data */
-+
-+ inst = devm_kzalloc(dev, sizeof(struct bcm2835_smi_instance),
-+ GFP_KERNEL);
-+
-+ if (!inst)
-+ return -ENOMEM;
-+
-+ inst->dev = dev;
-+ spin_lock_init(&inst->transaction_lock);
-+
-+ /* We require device tree support */
-+ if (!node)
-+ return -EINVAL;
-+
-+ ioresource = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+ inst->smi_regs_ptr = devm_ioremap_resource(dev, ioresource);
-+ ioresource = platform_get_resource(pdev, IORESOURCE_MEM, 1);
-+ inst->cm_smi_regs_ptr = devm_ioremap_resource(dev, ioresource);
-+ inst->smi_regs_busaddr = be32_to_cpu(
-+ *of_get_address(node, 0, NULL, NULL));
-+ of_property_read_u32(node,
-+ "brcm,smi-clock-source",
-+ &inst->clock_source);
-+ of_property_read_u32(node,
-+ "brcm,smi-clock-divisor",
-+ &inst->clock_divisor);
-+
-+ err = bcm2835_smi_dma_setup(inst);
-+ if (err)
-+ return err;
-+
-+ /* Finally, do peripheral setup */
-+
-+ smi_setup_clock(inst);
-+ smi_setup_regs(inst);
-+
-+ platform_set_drvdata(pdev, inst);
-+
-+ dev_info(inst->dev, "initialised");
-+
-+ return 0;
-+}
-+
-+/****************************************************************************
-+*
-+* bcm2835_smi_remove - called when the driver is unloaded.
-+*
-+***************************************************************************/
-+
-+static int bcm2835_smi_remove(struct platform_device *pdev)
-+{
-+ struct bcm2835_smi_instance *inst = platform_get_drvdata(pdev);
-+ struct device *dev = inst->dev;
-+
-+ dev_info(dev, "SMI device removed - OK");
-+ return 0;
-+}
-+
-+/****************************************************************************
-+*
-+* Register the driver with device tree
-+*
-+***************************************************************************/
-+
-+static const struct of_device_id bcm2835_smi_of_match[] = {
-+ {.compatible = "brcm,bcm2835-smi",},
-+ { /* sentinel */ },
-+};
-+
-+MODULE_DEVICE_TABLE(of, bcm2835_smi_of_match);
-+
-+static struct platform_driver bcm2835_smi_driver = {
-+ .probe = bcm2835_smi_probe,
-+ .remove = bcm2835_smi_remove,
-+ .driver = {
-+ .name = DRIVER_NAME,
-+ .owner = THIS_MODULE,
-+ .of_match_table = bcm2835_smi_of_match,
-+ },
-+};
-+
-+module_platform_driver(bcm2835_smi_driver);
-+
-+MODULE_ALIAS("platform:smi-bcm2835");
-+MODULE_LICENSE("GPL");
-+MODULE_DESCRIPTION("Device driver for BCM2835's secondary memory interface");
-+MODULE_AUTHOR("Luke Wren <luke at raspberrypi.org>");
---- /dev/null
-+++ b/include/linux/broadcom/bcm2835_smi.h
-@@ -0,0 +1,391 @@
-+/**
-+ * Declarations and definitions for Broadcom's Secondary Memory Interface
-+ *
-+ * Written by Luke Wren <luke at raspberrypi.org>
-+ * Copyright (c) 2015, Raspberry Pi (Trading) Ltd.
-+ * Copyright (c) 2010-2012 Broadcom. All rights reserved.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#ifndef BCM2835_SMI_H
-+#define BCM2835_SMI_H
-+
-+#include <linux/ioctl.h>
-+
-+#ifndef __KERNEL__
-+#include <stdint.h>
-+#include <stdbool.h>
-+#endif
-+
-+#define BCM2835_SMI_IOC_MAGIC 0x1
-+#define BCM2835_SMI_INVALID_HANDLE (~0)
-+
-+/* IOCTLs 0x100...0x1ff are not device-specific - we can use them */
-+#define BCM2835_SMI_IOC_GET_SETTINGS _IO(BCM2835_SMI_IOC_MAGIC, 0)
-+#define BCM2835_SMI_IOC_WRITE_SETTINGS _IO(BCM2835_SMI_IOC_MAGIC, 1)
-+#define BCM2835_SMI_IOC_ADDRESS _IO(BCM2835_SMI_IOC_MAGIC, 2)
-+#define BCM2835_SMI_IOC_MAX 2
-+
-+#define SMI_WIDTH_8BIT 0
-+#define SMI_WIDTH_16BIT 1
-+#define SMI_WIDTH_9BIT 2
-+#define SMI_WIDTH_18BIT 3
-+
-+/* max number of bytes where DMA will not be used */
-+#define DMA_THRESHOLD_BYTES 128
-+#define DMA_BOUNCE_BUFFER_SIZE (1024 * 1024 / 2)
-+#define DMA_BOUNCE_BUFFER_COUNT 3
-+
-+
-+struct smi_settings {
-+ int data_width;
-+ /* Whether or not to pack multiple SMI transfers into a
-+ single 32 bit FIFO word */
-+ bool pack_data;
-+
-+ /* Timing for reads (writes the same but for WE)
-+ *
-+ * OE ----------+ +--------------------
-+ * | |
-+ * +----------+
-+ * SD -<==============================>-----------
-+ * SA -<=========================================>-
-+ * <-setup-> <-strobe -> <-hold -> <- pace ->
-+ */
-+
-+ int read_setup_time;
-+ int read_hold_time;
-+ int read_pace_time;
-+ int read_strobe_time;
-+
-+ int write_setup_time;
-+ int write_hold_time;
-+ int write_pace_time;
-+ int write_strobe_time;
-+
-+ bool dma_enable; /* DREQs */
-+ bool dma_passthrough_enable; /* External DREQs */
-+ int dma_read_thresh;
-+ int dma_write_thresh;
-+ int dma_panic_read_thresh;
-+ int dma_panic_write_thresh;
-+};
-+
-+/****************************************************************************
-+*
-+* Declare exported SMI functions
-+*
-+***************************************************************************/
-+
-+#ifdef __KERNEL__
-+
-+#include <linux/dmaengine.h> /* for enum dma_transfer_direction */
-+#include <linux/of.h>
-+#include <linux/semaphore.h>
-+
-+struct bcm2835_smi_instance;
-+
-+struct bcm2835_smi_bounce_info {
-+ struct semaphore callback_sem;
-+ void *buffer[DMA_BOUNCE_BUFFER_COUNT];
-+ dma_addr_t phys[DMA_BOUNCE_BUFFER_COUNT];
-+ struct scatterlist sgl[DMA_BOUNCE_BUFFER_COUNT];
-+};
-+
-+
-+void bcm2835_smi_set_regs_from_settings(struct bcm2835_smi_instance *);
-+
-+struct smi_settings *bcm2835_smi_get_settings_from_regs(
-+ struct bcm2835_smi_instance *inst);
-+
-+void bcm2835_smi_write_buf(
-+ struct bcm2835_smi_instance *inst,
-+ const void *buf,
-+ size_t n_bytes);
-+
-+void bcm2835_smi_read_buf(
-+ struct bcm2835_smi_instance *inst,
-+ void *buf,
-+ size_t n_bytes);
-+
-+void bcm2835_smi_set_address(struct bcm2835_smi_instance *inst,
-+ unsigned int address);
-+
-+ssize_t bcm2835_smi_user_dma(
-+ struct bcm2835_smi_instance *inst,
-+ enum dma_transfer_direction dma_dir,
-+ char __user *user_ptr,
-+ size_t count,
-+ struct bcm2835_smi_bounce_info **bounce);
-+
-+struct bcm2835_smi_instance *bcm2835_smi_get(struct device_node *node);
-+
-+#endif /* __KERNEL__ */
-+
-+/****************************************************************
-+*
-+* Implementation-only declarations
-+*
-+****************************************************************/
-+
-+#ifdef BCM2835_SMI_IMPLEMENTATION
-+
-+/* Clock manager registers for SMI clock: */
-+#define CM_SMI_BASE_ADDRESS ((BCM2708_PERI_BASE) + 0x1010b0)
-+/* Clock manager "password" to protect registers from spurious writes */
-+#define CM_PWD (0x5a << 24)
-+
-+#define CM_SMI_CTL 0x00
-+#define CM_SMI_DIV 0x04
-+
-+#define CM_SMI_CTL_FLIP (1 << 8)
-+#define CM_SMI_CTL_BUSY (1 << 7)
-+#define CM_SMI_CTL_KILL (1 << 5)
-+#define CM_SMI_CTL_ENAB (1 << 4)
-+#define CM_SMI_CTL_SRC_MASK (0xf)
-+#define CM_SMI_CTL_SRC_OFFS (0)
-+
-+#define CM_SMI_DIV_DIVI_MASK (0xf << 12)
-+#define CM_SMI_DIV_DIVI_OFFS (12)
-+#define CM_SMI_DIV_DIVF_MASK (0xff << 4)
-+#define CM_SMI_DIV_DIVF_OFFS (4)
-+
-+/* SMI register mapping:*/
-+#define SMI_BASE_ADDRESS ((BCM2708_PERI_BASE) + 0x600000)
-+
-+#define SMICS 0x00 /* control + status register */
-+#define SMIL 0x04 /* length/count (n external txfers) */
-+#define SMIA 0x08 /* address register */
-+#define SMID 0x0c /* data register */
-+#define SMIDSR0 0x10 /* device 0 read settings */
-+#define SMIDSW0 0x14 /* device 0 write settings */
-+#define SMIDSR1 0x18 /* device 1 read settings */
-+#define SMIDSW1 0x1c /* device 1 write settings */
-+#define SMIDSR2 0x20 /* device 2 read settings */
-+#define SMIDSW2 0x24 /* device 2 write settings */
-+#define SMIDSR3 0x28 /* device 3 read settings */
-+#define SMIDSW3 0x2c /* device 3 write settings */
-+#define SMIDC 0x30 /* DMA control registers */
-+#define SMIDCS 0x34 /* direct control/status register */
-+#define SMIDA 0x38 /* direct address register */
-+#define SMIDD 0x3c /* direct data registers */
-+#define SMIFD 0x40 /* FIFO debug register */
-+
-+
-+
-+/* Control and Status register bits:
-+ * SMICS_RXF : RX fifo full: 1 when RX fifo is full
-+ * SMICS_TXE : TX fifo empty: 1 when empty.
-+ * SMICS_RXD : RX fifo contains data: 1 when there is data.
-+ * SMICS_TXD : TX fifo can accept data: 1 when true.
-+ * SMICS_RXR : RX fifo needs reading: 1 when fifo more than 3/4 full, or
-+ * when "DONE" and fifo not emptied.
-+ * SMICS_TXW : TX fifo needs writing: 1 when less than 1/4 full.
-+ * SMICS_AFERR : AXI FIFO error: 1 when fifo read when empty or written
-+ * when full. Write 1 to clear.
-+ * SMICS_EDREQ : 1 when external DREQ received.
-+ * SMICS_PXLDAT : Pixel data: write 1 to enable pixel transfer modes.
-+ * SMICS_SETERR : 1 if there was an error writing to setup regs (e.g.
-+ * tx was in progress). Write 1 to clear.
-+ * SMICS_PVMODE : Set to 1 to enable pixel valve mode.
-+ * SMICS_INTR : Set to 1 to enable interrupt on RX.
-+ * SMICS_INTT : Set to 1 to enable interrupt on TX.
-+ * SMICS_INTD : Set to 1 to enable interrupt on DONE condition.
-+ * SMICS_TEEN : Tear effect mode enabled: Programmed transfers will wait
-+ * for a TE trigger before writing.
-+ * SMICS_PAD1 : Padding settings for external transfers. For writes: the
-+ * number of bytes initially written to the TX fifo that
-+ * SMICS_PAD0 : should be ignored. For reads: the number of bytes that will
-+ * be read before the data, and should be dropped.
-+ * SMICS_WRITE : Transfer direction: 1 = write to external device, 0 = read
-+ * SMICS_CLEAR : Write 1 to clear the FIFOs.
-+ * SMICS_START : Write 1 to start the programmed transfer.
-+ * SMICS_ACTIVE : Reads as 1 when a programmed transfer is underway.
-+ * SMICS_DONE : Reads as 1 when transfer finished. For RX, not set until
-+ * FIFO emptied.
-+ * SMICS_ENABLE : Set to 1 to enable the SMI peripheral, 0 to disable.
-+ */
-+
-+#define SMICS_RXF (1 << 31)
-+#define SMICS_TXE (1 << 30)
-+#define SMICS_RXD (1 << 29)
-+#define SMICS_TXD (1 << 28)
-+#define SMICS_RXR (1 << 27)
-+#define SMICS_TXW (1 << 26)
-+#define SMICS_AFERR (1 << 25)
-+#define SMICS_EDREQ (1 << 15)
-+#define SMICS_PXLDAT (1 << 14)
-+#define SMICS_SETERR (1 << 13)
-+#define SMICS_PVMODE (1 << 12)
-+#define SMICS_INTR (1 << 11)
-+#define SMICS_INTT (1 << 10)
-+#define SMICS_INTD (1 << 9)
-+#define SMICS_TEEN (1 << 8)
-+#define SMICS_PAD1 (1 << 7)
-+#define SMICS_PAD0 (1 << 6)
-+#define SMICS_WRITE (1 << 5)
-+#define SMICS_CLEAR (1 << 4)
-+#define SMICS_START (1 << 3)
-+#define SMICS_ACTIVE (1 << 2)
-+#define SMICS_DONE (1 << 1)
-+#define SMICS_ENABLE (1 << 0)
-+
-+/* Address register bits: */
-+
-+#define SMIA_DEVICE_MASK ((1 << 9) | (1 << 8))
-+#define SMIA_DEVICE_OFFS (8)
-+#define SMIA_ADDR_MASK (0x3f) /* bits 5 -> 0 */
-+#define SMIA_ADDR_OFFS (0)
-+
-+/* DMA control register bits:
-+ * SMIDC_DMAEN : DMA enable: set 1: DMA requests will be issued.
-+ * SMIDC_DMAP : DMA passthrough: when set to 0, top two data pins are used by
-+ * SMI as usual. When set to 1, the top two pins are used for
-+ * external DREQs: pin 16 read request, 17 write.
-+ * SMIDC_PANIC* : Threshold at which DMA will panic during read/write.
-+ * SMIDC_REQ* : Threshold at which DMA will generate a DREQ.
-+ */
-+
-+#define SMIDC_DMAEN (1 << 28)
-+#define SMIDC_DMAP (1 << 24)
-+#define SMIDC_PANICR_MASK (0x3f << 18)
-+#define SMIDC_PANICR_OFFS (18)
-+#define SMIDC_PANICW_MASK (0x3f << 12)
-+#define SMIDC_PANICW_OFFS (12)
-+#define SMIDC_REQR_MASK (0x3f << 6)
-+#define SMIDC_REQR_OFFS (6)
-+#define SMIDC_REQW_MASK (0x3f)
-+#define SMIDC_REQW_OFFS (0)
-+
-+/* Device settings register bits: same for all 4 (or 3?) device register sets.
-+ * Device read settings:
-+ * SMIDSR_RWIDTH : Read transfer width. 00 = 8bit, 01 = 16bit,
-+ * 10 = 18bit, 11 = 9bit.
-+ * SMIDSR_RSETUP : Read setup time: number of core cycles between chip
-+ * select/address and read strobe. Min 1, max 64.
-+ * SMIDSR_MODE68 : 1 for System 68 mode (i.e. enable + direction pins,
-+ * rather than OE + WE pin)
-+ * SMIDSR_FSETUP : If set to 1, setup time only applies to first
-+ * transfer after address change.
-+ * SMIDSR_RHOLD : Number of core cycles between read strobe going
-+ * inactive and CS/address going inactive. Min 1, max 64
-+ * SMIDSR_RPACEALL : When set to 1, this device's RPACE value will always
-+ * be used for the next transaction, even if it is not
-+ * to this device.
-+ * SMIDSR_RPACE : Number of core cycles spent waiting between CS
-+ * deassert and start of next transfer. Min 1, max 128
-+ * SMIDSR_RDREQ : 1 = use external DMA request on SD16 to pace reads
-+ * from device. Must also set DMAP in SMICS.
-+ * SMIDSR_RSTROBE : Number of cycles to assert the read strobe.
-+ * min 1, max 128.
-+ */
-+#define SMIDSR_RWIDTH_MASK ((1<<31)|(1<<30))
-+#define SMIDSR_RWIDTH_OFFS (30)
-+#define SMIDSR_RSETUP_MASK (0x3f << 24)
-+#define SMIDSR_RSETUP_OFFS (24)
-+#define SMIDSR_MODE68 (1 << 23)
-+#define SMIDSR_FSETUP (1 << 22)
-+#define SMIDSR_RHOLD_MASK (0x3f << 16)
-+#define SMIDSR_RHOLD_OFFS (16)
-+#define SMIDSR_RPACEALL (1 << 15)
-+#define SMIDSR_RPACE_MASK (0x7f << 8)
-+#define SMIDSR_RPACE_OFFS (8)
-+#define SMIDSR_RDREQ (1 << 7)
-+#define SMIDSR_RSTROBE_MASK (0x7f)
-+#define SMIDSR_RSTROBE_OFFS (0)
-+
-+/* Device write settings:
-+ * SMIDSW_WWIDTH : Write transfer width. 00 = 8bit, 01 = 16bit,
-+ * 10= 18bit, 11 = 9bit.
-+ * SMIDSW_WSETUP : Number of cycles between CS assert and write strobe.
-+ * Min 1, max 64.
-+ * SMIDSW_WFORMAT : Pixel format of input. 0 = 16bit RGB 565,
-+ * 1 = 32bit RGBA 8888
-+ * SMIDSW_WSWAP : 1 = swap pixel data bits. (Use with SMICS_PXLDAT)
-+ * SMIDSW_WHOLD : Time between WE deassert and CS deassert. 1 to 64
-+ * SMIDSW_WPACEALL : 1: this device's WPACE will be used for the next
-+ * transfer, regardless of that transfer's device.
-+ * SMIDSW_WPACE : Cycles between CS deassert and next CS assert.
-+ * Min 1, max 128
-+ * SMIDSW_WDREQ : Use external DREQ on pin 17 to pace writes. DMAP must
-+ * be set in SMICS.
-+ * SMIDSW_WSTROBE : Number of cycles to assert the write strobe.
-+ * Min 1, max 128
-+ */
-+#define SMIDSW_WWIDTH_MASK ((1<<31)|(1<<30))
-+#define SMIDSW_WWIDTH_OFFS (30)
-+#define SMIDSW_WSETUP_MASK (0x3f << 24)
-+#define SMIDSW_WSETUP_OFFS (24)
-+#define SMIDSW_WFORMAT (1 << 23)
-+#define SMIDSW_WSWAP (1 << 22)
-+#define SMIDSW_WHOLD_MASK (0x3f << 16)
-+#define SMIDSW_WHOLD_OFFS (16)
-+#define SMIDSW_WPACEALL (1 << 15)
-+#define SMIDSW_WPACE_MASK (0x7f << 8)
-+#define SMIDSW_WPACE_OFFS (8)
-+#define SMIDSW_WDREQ (1 << 7)
-+#define SMIDSW_WSTROBE_MASK (0x7f)
-+#define SMIDSW_WSTROBE_OFFS (0)
-+
-+/* Direct transfer control + status register
-+ * SMIDCS_WRITE : Direction of transfer: 1 -> write, 0 -> read
-+ * SMIDCS_DONE : 1 when a transfer has finished. Write 1 to clear.
-+ * SMIDCS_START : Write 1 to start a transfer, if one is not already underway.
-+ * SMIDCE_ENABLE: Write 1 to enable SMI in direct mode.
-+ */
-+
-+#define SMIDCS_WRITE (1 << 3)
-+#define SMIDCS_DONE (1 << 2)
-+#define SMIDCS_START (1 << 1)
-+#define SMIDCS_ENABLE (1 << 0)
-+
-+/* Direct transfer address register
-+ * SMIDA_DEVICE : Indicates which of the device settings banks should be used.
-+ * SMIDA_ADDR : The value to be asserted on the address pins.
-+ */
-+
-+#define SMIDA_DEVICE_MASK ((1<<9)|(1<<8))
-+#define SMIDA_DEVICE_OFFS (8)
-+#define SMIDA_ADDR_MASK (0x3f)
-+#define SMIDA_ADDR_OFFS (0)
-+
-+/* FIFO debug register
-+ * SMIFD_FLVL : The high-tide mark of FIFO count during the most recent txfer
-+ * SMIFD_FCNT : The current FIFO count.
-+ */
-+#define SMIFD_FLVL_MASK (0x3f << 8)
-+#define SMIFD_FLVL_OFFS (8)
-+#define SMIFD_FCNT_MASK (0x3f)
-+#define SMIFD_FCNT_OFFS (0)
-+
-+#endif /* BCM2835_SMI_IMPLEMENTATION */
-+
-+#endif /* BCM2835_SMI_H */
diff --git a/target/linux/brcm2708/patches-4.4/0041-Add-SMI-NAND-driver.patch b/target/linux/brcm2708/patches-4.4/0041-Add-SMI-NAND-driver.patch
deleted file mode 100644
index 58c83aa..0000000
--- a/target/linux/brcm2708/patches-4.4/0041-Add-SMI-NAND-driver.patch
+++ /dev/null
@@ -1,358 +0,0 @@
-From 547bbe5578accad0c4f0a7461d5f2b99674f1e51 Mon Sep 17 00:00:00 2001
-From: Luke Wren <wren6991 at gmail.com>
-Date: Sat, 5 Sep 2015 01:16:10 +0100
-Subject: [PATCH] Add SMI NAND driver
-
-Signed-off-by: Luke Wren <wren6991 at gmail.com>
----
- .../bindings/mtd/brcm,bcm2835-smi-nand.txt | 42 ++++
- drivers/mtd/nand/Kconfig | 7 +
- drivers/mtd/nand/Makefile | 1 +
- drivers/mtd/nand/bcm2835_smi_nand.c | 268 +++++++++++++++++++++
- 4 files changed, 318 insertions(+)
- create mode 100644 Documentation/devicetree/bindings/mtd/brcm,bcm2835-smi-nand.txt
- create mode 100644 drivers/mtd/nand/bcm2835_smi_nand.c
-
---- /dev/null
-+++ b/Documentation/devicetree/bindings/mtd/brcm,bcm2835-smi-nand.txt
-@@ -0,0 +1,42 @@
-+* BCM2835 SMI NAND flash
-+
-+This driver is a shim between the BCM2835 SMI driver (SMI is a peripheral for
-+talking to parallel register interfaces) and Linux's MTD layer.
-+
-+Required properties:
-+- compatible: "brcm,bcm2835-smi-nand"
-+- status: "okay"
-+
-+Optional properties:
-+- partition at n, where n is an integer from a consecutive sequence starting at 0
-+ - Difficult to store partition table on NAND device - normally put it
-+ in the source code, kernel bootparams, or device tree (the best way!)
-+ - Sub-properties:
-+ - label: the partition name, as shown by mtdinfo /dev/mtd*
-+ - reg: the size and offset of this partition.
-+ - (optional) read-only: an empty property flagging as read only
-+
-+Example:
-+
-+nand: flash at 0 {
-+ compatible = "brcm,bcm2835-smi-nand";
-+ status = "okay";
-+
-+ partition at 0 {
-+ label = "stage2";
-+ // 128k
-+ reg = <0 0x20000>;
-+ read-only;
-+ };
-+ partition at 1 {
-+ label = "firmware";
-+ // 16M
-+ reg = <0x20000 0x1000000>;
-+ read-only;
-+ };
-+ partition at 2 {
-+ label = "root";
-+ // 2G
-+ reg = <0x1020000 0x80000000>;
-+ };
-+};
-\ No newline at end of file
---- a/drivers/mtd/nand/Kconfig
-+++ b/drivers/mtd/nand/Kconfig
-@@ -41,6 +41,13 @@ config MTD_SM_COMMON
- tristate
- default n
-
-+config MTD_NAND_BCM2835_SMI
-+ tristate "Use Broadcom's Secondary Memory Interface as a NAND controller (BCM283x)"
-+ depends on (MACH_BCM2708 || MACH_BCM2709 || ARCH_BCM2835) && BCM2835_SMI && MTD_NAND
-+ default m
-+ help
-+ Uses the BCM2835's SMI peripheral as a NAND controller.
-+
- config MTD_NAND_DENALI
- tristate
-
---- a/drivers/mtd/nand/Makefile
-+++ b/drivers/mtd/nand/Makefile
-@@ -14,6 +14,7 @@ obj-$(CONFIG_MTD_NAND_DENALI) += denali
- obj-$(CONFIG_MTD_NAND_DENALI_PCI) += denali_pci.o
- obj-$(CONFIG_MTD_NAND_DENALI_DT) += denali_dt.o
- obj-$(CONFIG_MTD_NAND_AU1550) += au1550nd.o
-+obj-$(CONFIG_MTD_NAND_BCM2835_SMI) += bcm2835_smi_nand.o
- obj-$(CONFIG_MTD_NAND_BF5XX) += bf5xx_nand.o
- obj-$(CONFIG_MTD_NAND_S3C2410) += s3c2410.o
- obj-$(CONFIG_MTD_NAND_DAVINCI) += davinci_nand.o
---- /dev/null
-+++ b/drivers/mtd/nand/bcm2835_smi_nand.c
-@@ -0,0 +1,268 @@
-+/**
-+ * NAND flash driver for Broadcom Secondary Memory Interface
-+ *
-+ * Written by Luke Wren <luke at raspberrypi.org>
-+ * Copyright (c) 2015, Raspberry Pi (Trading) Ltd.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+#include <linux/of.h>
-+#include <linux/platform_device.h>
-+#include <linux/slab.h>
-+#include <linux/mtd/nand.h>
-+#include <linux/mtd/partitions.h>
-+
-+#include <linux/broadcom/bcm2835_smi.h>
-+
-+#define DEVICE_NAME "bcm2835-smi-nand"
-+#define DRIVER_NAME "smi-nand-bcm2835"
-+
-+struct bcm2835_smi_nand_host {
-+ struct bcm2835_smi_instance *smi_inst;
-+ struct nand_chip nand_chip;
-+ struct mtd_info mtd;
-+ struct device *dev;
-+};
-+
-+/****************************************************************************
-+*
-+* NAND functionality implementation
-+*
-+****************************************************************************/
-+
-+#define SMI_NAND_CLE_PIN 0x01
-+#define SMI_NAND_ALE_PIN 0x02
-+
-+static inline void bcm2835_smi_nand_cmd_ctrl(struct mtd_info *mtd, int cmd,
-+ unsigned int ctrl)
-+{
-+ uint32_t cmd32 = cmd;
-+ uint32_t addr = ~(SMI_NAND_CLE_PIN | SMI_NAND_ALE_PIN);
-+ struct bcm2835_smi_nand_host *host = dev_get_drvdata(mtd->dev.parent);
-+ struct bcm2835_smi_instance *inst = host->smi_inst;
-+
-+ if (ctrl & NAND_CLE)
-+ addr |= SMI_NAND_CLE_PIN;
-+ if (ctrl & NAND_ALE)
-+ addr |= SMI_NAND_ALE_PIN;
-+ /* Lower ALL the CS pins! */
-+ if (ctrl & NAND_NCE)
-+ addr &= (SMI_NAND_CLE_PIN | SMI_NAND_ALE_PIN);
-+
-+ bcm2835_smi_set_address(inst, addr);
-+
-+ if (cmd != NAND_CMD_NONE)
-+ bcm2835_smi_write_buf(inst, &cmd32, 1);
-+}
-+
-+static inline uint8_t bcm2835_smi_nand_read_byte(struct mtd_info *mtd)
-+{
-+ uint8_t byte;
-+ struct bcm2835_smi_nand_host *host = dev_get_drvdata(mtd->dev.parent);
-+ struct bcm2835_smi_instance *inst = host->smi_inst;
-+
-+ bcm2835_smi_read_buf(inst, &byte, 1);
-+ return byte;
-+}
-+
-+static inline void bcm2835_smi_nand_write_byte(struct mtd_info *mtd,
-+ uint8_t byte)
-+{
-+ struct bcm2835_smi_nand_host *host = dev_get_drvdata(mtd->dev.parent);
-+ struct bcm2835_smi_instance *inst = host->smi_inst;
-+
-+ bcm2835_smi_write_buf(inst, &byte, 1);
-+}
-+
-+static inline void bcm2835_smi_nand_write_buf(struct mtd_info *mtd,
-+ const uint8_t *buf, int len)
-+{
-+ struct bcm2835_smi_nand_host *host = dev_get_drvdata(mtd->dev.parent);
-+ struct bcm2835_smi_instance *inst = host->smi_inst;
-+
-+ bcm2835_smi_write_buf(inst, buf, len);
-+}
-+
-+static inline void bcm2835_smi_nand_read_buf(struct mtd_info *mtd,
-+ uint8_t *buf, int len)
-+{
-+ struct bcm2835_smi_nand_host *host = dev_get_drvdata(mtd->dev.parent);
-+ struct bcm2835_smi_instance *inst = host->smi_inst;
-+
-+ bcm2835_smi_read_buf(inst, buf, len);
-+}
-+
-+/****************************************************************************
-+*
-+* Probe and remove functions
-+*
-+***************************************************************************/
-+
-+static int bcm2835_smi_nand_probe(struct platform_device *pdev)
-+{
-+ struct bcm2835_smi_nand_host *host;
-+ struct nand_chip *this;
-+ struct mtd_info *mtd;
-+ struct device *dev = &pdev->dev;
-+ struct device_node *node = dev->of_node, *smi_node;
-+ struct mtd_part_parser_data ppdata;
-+ struct smi_settings *smi_settings;
-+ struct bcm2835_smi_instance *smi_inst;
-+ int ret = -ENXIO;
-+
-+ if (!node) {
-+ dev_err(dev, "No device tree node supplied!");
-+ return -EINVAL;
-+ }
-+
-+ smi_node = of_parse_phandle(node, "smi_handle", 0);
-+
-+ /* Request use of SMI peripheral: */
-+ smi_inst = bcm2835_smi_get(smi_node);
-+
-+ if (!smi_inst) {
-+ dev_err(dev, "Could not register with SMI.");
-+ return -EPROBE_DEFER;
-+ }
-+
-+ /* Set SMI timing and bus width */
-+
-+ smi_settings = bcm2835_smi_get_settings_from_regs(smi_inst);
-+
-+ smi_settings->data_width = SMI_WIDTH_8BIT;
-+ smi_settings->read_setup_time = 2;
-+ smi_settings->read_hold_time = 1;
-+ smi_settings->read_pace_time = 1;
-+ smi_settings->read_strobe_time = 3;
-+
-+ smi_settings->write_setup_time = 2;
-+ smi_settings->write_hold_time = 1;
-+ smi_settings->write_pace_time = 1;
-+ smi_settings->write_strobe_time = 3;
-+
-+ bcm2835_smi_set_regs_from_settings(smi_inst);
-+
-+ host = devm_kzalloc(dev, sizeof(struct bcm2835_smi_nand_host),
-+ GFP_KERNEL);
-+ if (!host)
-+ return -ENOMEM;
-+
-+ host->dev = dev;
-+ host->smi_inst = smi_inst;
-+
-+ platform_set_drvdata(pdev, host);
-+
-+ /* Link the structures together */
-+
-+ this = &host->nand_chip;
-+ mtd = &host->mtd;
-+ mtd->priv = this;
-+ mtd->owner = THIS_MODULE;
-+ mtd->dev.parent = dev;
-+ mtd->name = DRIVER_NAME;
-+ ppdata.of_node = node;
-+
-+ /* 20 us command delay time... */
-+ this->chip_delay = 20;
-+
-+ this->priv = host;
-+ this->cmd_ctrl = bcm2835_smi_nand_cmd_ctrl;
-+ this->read_byte = bcm2835_smi_nand_read_byte;
-+ this->write_byte = bcm2835_smi_nand_write_byte;
-+ this->write_buf = bcm2835_smi_nand_write_buf;
-+ this->read_buf = bcm2835_smi_nand_read_buf;
-+
-+ this->ecc.mode = NAND_ECC_SOFT;
-+
-+ /* Should never be accessed directly: */
-+
-+ this->IO_ADDR_R = (void *)0xdeadbeef;
-+ this->IO_ADDR_W = (void *)0xdeadbeef;
-+
-+ /* First scan to find the device and get the page size */
-+
-+ if (nand_scan_ident(mtd, 1, NULL))
-+ return -ENXIO;
-+
-+ /* Second phase scan */
-+
-+ if (nand_scan_tail(mtd))
-+ return -ENXIO;
-+
-+ ret = mtd_device_parse_register(mtd, NULL, &ppdata, NULL, 0);
-+ if (!ret)
-+ return 0;
-+
-+ nand_release(mtd);
-+ return -EINVAL;
-+}
-+
-+static int bcm2835_smi_nand_remove(struct platform_device *pdev)
-+{
-+ struct bcm2835_smi_nand_host *host = platform_get_drvdata(pdev);
-+
-+ nand_release(&host->mtd);
-+
-+ return 0;
-+}
-+
-+/****************************************************************************
-+*
-+* Register the driver with device tree
-+*
-+***************************************************************************/
-+
-+static const struct of_device_id bcm2835_smi_nand_of_match[] = {
-+ {.compatible = "brcm,bcm2835-smi-nand",},
-+ { /* sentinel */ }
-+};
-+
-+MODULE_DEVICE_TABLE(of, bcm2835_smi_nand_of_match);
-+
-+static struct platform_driver bcm2835_smi_nand_driver = {
-+ .probe = bcm2835_smi_nand_probe,
-+ .remove = bcm2835_smi_nand_remove,
-+ .driver = {
-+ .name = DRIVER_NAME,
-+ .owner = THIS_MODULE,
-+ .of_match_table = bcm2835_smi_nand_of_match,
-+ },
-+};
-+
-+module_platform_driver(bcm2835_smi_nand_driver);
-+
-+MODULE_ALIAS("platform:smi-nand-bcm2835");
-+MODULE_LICENSE("GPL");
-+MODULE_DESCRIPTION
-+ ("Driver for NAND chips using Broadcom Secondary Memory Interface");
-+MODULE_AUTHOR("Luke Wren <luke at raspberrypi.org>");
diff --git a/target/linux/brcm2708/patches-4.4/0042-lirc-added-support-for-RaspberryPi-GPIO.patch b/target/linux/brcm2708/patches-4.4/0042-lirc-added-support-for-RaspberryPi-GPIO.patch
deleted file mode 100644
index 694a866..0000000
--- a/target/linux/brcm2708/patches-4.4/0042-lirc-added-support-for-RaspberryPi-GPIO.patch
+++ /dev/null
@@ -1,841 +0,0 @@
-From e39854b38284178a8c63b4dc160d5883c2ce0a42 Mon Sep 17 00:00:00 2001
-From: Aron Szabo <aron at aron.ws>
-Date: Sat, 16 Jun 2012 12:15:55 +0200
-Subject: [PATCH] lirc: added support for RaspberryPi GPIO
-
-lirc_rpi: Use read_current_timer to determine transmitter delay. Thanks to jjmz and others
-See: https://github.com/raspberrypi/linux/issues/525
-
-lirc: Remove restriction on gpio pins that can be used with lirc
-
-Compute Module, for example could use different pins
-
-lirc_rpi: Add parameter to specify input pin pull
-
-Depending on the connected IR circuitry it might be desirable to change the
-gpios internal pull from it pull-down default behaviour. Add a module
-parameter to allow the user to set it explicitly.
-
-Signed-off-by: Julian Scheel <julian at jusst.de>
-
-lirc-rpi: Use the higher-level irq control functions
-
-This module used to access the irq_chip methods of the
-gpio controller directly, rather than going through the
-standard enable_irq/irq_set_irq_type functions. This
-caused problems on pinctrl-bcm2835 which only implements
-the irq_enable/disable methods and not irq_unmask/mask.
-
-lirc-rpi: Correct the interrupt usage
-
-1) Correct the use of enable_irq (i.e. don't call it so often)
-2) Correct the shutdown sequence.
-3) Avoid a bcm2708_gpio driver quirk by setting the irq flags earlier
-
-lirc-rpi: use getnstimeofday instead of read_current_timer
-
-read_current_timer isn't guaranteed to return values in
-microseconds, and indeed it doesn't on a Pi2.
-
-Issue: linux#827
-
-lirc-rpi: Add device tree support, and a suitable overlay
-
-The overlay supports DT parameters that match the old module
-parameters, except that gpio_in_pull should be set using the
-strings "up", "down" or "off".
-
-lirc-rpi: Also support pinctrl-bcm2835 in non-DT mode
----
- drivers/staging/media/lirc/Kconfig | 6 +
- drivers/staging/media/lirc/Makefile | 1 +
- drivers/staging/media/lirc/lirc_rpi.c | 730 ++++++++++++++++++++++++++++++++++
- include/linux/platform_data/bcm2708.h | 23 ++
- 4 files changed, 760 insertions(+)
- create mode 100644 drivers/staging/media/lirc/lirc_rpi.c
- create mode 100644 include/linux/platform_data/bcm2708.h
-
---- a/drivers/staging/media/lirc/Kconfig
-+++ b/drivers/staging/media/lirc/Kconfig
-@@ -32,6 +32,12 @@ config LIRC_PARALLEL
- help
- Driver for Homebrew Parallel Port Receivers
-
-+config LIRC_RPI
-+ tristate "Homebrew GPIO Port Receiver/Transmitter for the RaspberryPi"
-+ depends on LIRC
-+ help
-+ Driver for Homebrew GPIO Port Receiver/Transmitter for the RaspberryPi
-+
- config LIRC_SASEM
- tristate "Sasem USB IR Remote"
- depends on LIRC && USB
---- a/drivers/staging/media/lirc/Makefile
-+++ b/drivers/staging/media/lirc/Makefile
-@@ -6,6 +6,7 @@
- obj-$(CONFIG_LIRC_BT829) += lirc_bt829.o
- obj-$(CONFIG_LIRC_IMON) += lirc_imon.o
- obj-$(CONFIG_LIRC_PARALLEL) += lirc_parallel.o
-+obj-$(CONFIG_LIRC_RPI) += lirc_rpi.o
- obj-$(CONFIG_LIRC_SASEM) += lirc_sasem.o
- obj-$(CONFIG_LIRC_SERIAL) += lirc_serial.o
- obj-$(CONFIG_LIRC_SIR) += lirc_sir.o
---- /dev/null
-+++ b/drivers/staging/media/lirc/lirc_rpi.c
-@@ -0,0 +1,730 @@
-+/*
-+ * lirc_rpi.c
-+ *
-+ * lirc_rpi - Device driver that records pulse- and pause-lengths
-+ * (space-lengths) (just like the lirc_serial driver does)
-+ * between GPIO interrupt events on the Raspberry Pi.
-+ * Lots of code has been taken from the lirc_serial module,
-+ * so I would like say thanks to the authors.
-+ *
-+ * Copyright (C) 2012 Aron Robert Szabo <aron at reon.hu>,
-+ * Michael Bishop <cleverca22 at gmail.com>
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/errno.h>
-+#include <linux/interrupt.h>
-+#include <linux/sched.h>
-+#include <linux/kernel.h>
-+#include <linux/time.h>
-+#include <linux/timex.h>
-+#include <linux/timekeeping.h>
-+#include <linux/string.h>
-+#include <linux/delay.h>
-+#include <linux/platform_device.h>
-+#include <linux/irq.h>
-+#include <linux/spinlock.h>
-+#include <media/lirc.h>
-+#include <media/lirc_dev.h>
-+#include <linux/gpio.h>
-+#include <linux/of_platform.h>
-+#include <linux/platform_data/bcm2708.h>
-+
-+#define LIRC_DRIVER_NAME "lirc_rpi"
-+#define RBUF_LEN 256
-+#define LIRC_TRANSMITTER_LATENCY 50
-+
-+#ifndef MAX_UDELAY_MS
-+#define MAX_UDELAY_US 5000
-+#else
-+#define MAX_UDELAY_US (MAX_UDELAY_MS*1000)
-+#endif
-+
-+#define dprintk(fmt, args...) \
-+ do { \
-+ if (debug) \
-+ printk(KERN_DEBUG LIRC_DRIVER_NAME ": " \
-+ fmt, ## args); \
-+ } while (0)
-+
-+/* module parameters */
-+
-+/* set the default GPIO input pin */
-+static int gpio_in_pin = 18;
-+/* set the default pull behaviour for input pin */
-+static int gpio_in_pull = BCM2708_PULL_DOWN;
-+/* set the default GPIO output pin */
-+static int gpio_out_pin = 17;
-+/* enable debugging messages */
-+static bool debug;
-+/* -1 = auto, 0 = active high, 1 = active low */
-+static int sense = -1;
-+/* use softcarrier by default */
-+static bool softcarrier = 1;
-+/* 0 = do not invert output, 1 = invert output */
-+static bool invert = 0;
-+
-+struct gpio_chip *gpiochip;
-+static int irq_num;
-+
-+/* forward declarations */
-+static long send_pulse(unsigned long length);
-+static void send_space(long length);
-+static void lirc_rpi_exit(void);
-+
-+static struct platform_device *lirc_rpi_dev;
-+static struct timeval lasttv = { 0, 0 };
-+static struct lirc_buffer rbuf;
-+static spinlock_t lock;
-+
-+/* initialized/set in init_timing_params() */
-+static unsigned int freq = 38000;
-+static unsigned int duty_cycle = 50;
-+static unsigned long period;
-+static unsigned long pulse_width;
-+static unsigned long space_width;
-+
-+static void safe_udelay(unsigned long usecs)
-+{
-+ while (usecs > MAX_UDELAY_US) {
-+ udelay(MAX_UDELAY_US);
-+ usecs -= MAX_UDELAY_US;
-+ }
-+ udelay(usecs);
-+}
-+
-+static unsigned long read_current_us(void)
-+{
-+ struct timespec now;
-+ getnstimeofday(&now);
-+ return (now.tv_sec * 1000000) + (now.tv_nsec/1000);
-+}
-+
-+static int init_timing_params(unsigned int new_duty_cycle,
-+ unsigned int new_freq)
-+{
-+ if (1000 * 1000000L / new_freq * new_duty_cycle / 100 <=
-+ LIRC_TRANSMITTER_LATENCY)
-+ return -EINVAL;
-+ if (1000 * 1000000L / new_freq * (100 - new_duty_cycle) / 100 <=
-+ LIRC_TRANSMITTER_LATENCY)
-+ return -EINVAL;
-+ duty_cycle = new_duty_cycle;
-+ freq = new_freq;
-+ period = 1000 * 1000000L / freq;
-+ pulse_width = period * duty_cycle / 100;
-+ space_width = period - pulse_width;
-+ dprintk("in init_timing_params, freq=%d pulse=%ld, "
-+ "space=%ld\n", freq, pulse_width, space_width);
-+ return 0;
-+}
-+
-+static long send_pulse_softcarrier(unsigned long length)
-+{
-+ int flag;
-+ unsigned long actual, target;
-+ unsigned long actual_us, initial_us, target_us;
-+
-+ length *= 1000;
-+
-+ actual = 0; target = 0; flag = 0;
-+ actual_us = read_current_us();
-+
-+ while (actual < length) {
-+ if (flag) {
-+ gpiochip->set(gpiochip, gpio_out_pin, invert);
-+ target += space_width;
-+ } else {
-+ gpiochip->set(gpiochip, gpio_out_pin, !invert);
-+ target += pulse_width;
-+ }
-+ initial_us = actual_us;
-+ target_us = actual_us + (target - actual) / 1000;
-+ /*
-+ * Note - we've checked in ioctl that the pulse/space
-+ * widths are big enough so that d is > 0
-+ */
-+ if ((int)(target_us - actual_us) > 0)
-+ udelay(target_us - actual_us);
-+ actual_us = read_current_us();
-+ actual += (actual_us - initial_us) * 1000;
-+ flag = !flag;
-+ }
-+ return (actual-length) / 1000;
-+}
-+
-+static long send_pulse(unsigned long length)
-+{
-+ if (length <= 0)
-+ return 0;
-+
-+ if (softcarrier) {
-+ return send_pulse_softcarrier(length);
-+ } else {
-+ gpiochip->set(gpiochip, gpio_out_pin, !invert);
-+ safe_udelay(length);
-+ return 0;
-+ }
-+}
-+
-+static void send_space(long length)
-+{
-+ gpiochip->set(gpiochip, gpio_out_pin, invert);
-+ if (length <= 0)
-+ return;
-+ safe_udelay(length);
-+}
-+
-+static void rbwrite(int l)
-+{
-+ if (lirc_buffer_full(&rbuf)) {
-+ /* no new signals will be accepted */
-+ dprintk("Buffer overrun\n");
-+ return;
-+ }
-+ lirc_buffer_write(&rbuf, (void *)&l);
-+}
-+
-+static void frbwrite(int l)
-+{
-+ /* simple noise filter */
-+ static int pulse, space;
-+ static unsigned int ptr;
-+
-+ if (ptr > 0 && (l & PULSE_BIT)) {
-+ pulse += l & PULSE_MASK;
-+ if (pulse > 250) {
-+ rbwrite(space);
-+ rbwrite(pulse | PULSE_BIT);
-+ ptr = 0;
-+ pulse = 0;
-+ }
-+ return;
-+ }
-+ if (!(l & PULSE_BIT)) {
-+ if (ptr == 0) {
-+ if (l > 20000) {
-+ space = l;
-+ ptr++;
-+ return;
-+ }
-+ } else {
-+ if (l > 20000) {
-+ space += pulse;
-+ if (space > PULSE_MASK)
-+ space = PULSE_MASK;
-+ space += l;
-+ if (space > PULSE_MASK)
-+ space = PULSE_MASK;
-+ pulse = 0;
-+ return;
-+ }
-+ rbwrite(space);
-+ rbwrite(pulse | PULSE_BIT);
-+ ptr = 0;
-+ pulse = 0;
-+ }
-+ }
-+ rbwrite(l);
-+}
-+
-+static irqreturn_t irq_handler(int i, void *blah, struct pt_regs *regs)
-+{
-+ struct timeval tv;
-+ long deltv;
-+ int data;
-+ int signal;
-+
-+ /* use the GPIO signal level */
-+ signal = gpiochip->get(gpiochip, gpio_in_pin);
-+
-+ if (sense != -1) {
-+ /* get current time */
-+ do_gettimeofday(&tv);
-+
-+ /* calc time since last interrupt in microseconds */
-+ deltv = tv.tv_sec-lasttv.tv_sec;
-+ if (tv.tv_sec < lasttv.tv_sec ||
-+ (tv.tv_sec == lasttv.tv_sec &&
-+ tv.tv_usec < lasttv.tv_usec)) {
-+ printk(KERN_WARNING LIRC_DRIVER_NAME
-+ ": AIEEEE: your clock just jumped backwards\n");
-+ printk(KERN_WARNING LIRC_DRIVER_NAME
-+ ": %d %d %lx %lx %lx %lx\n", signal, sense,
-+ tv.tv_sec, lasttv.tv_sec,
-+ tv.tv_usec, lasttv.tv_usec);
-+ data = PULSE_MASK;
-+ } else if (deltv > 15) {
-+ data = PULSE_MASK; /* really long time */
-+ if (!(signal^sense)) {
-+ /* sanity check */
-+ printk(KERN_WARNING LIRC_DRIVER_NAME
-+ ": AIEEEE: %d %d %lx %lx %lx %lx\n",
-+ signal, sense, tv.tv_sec, lasttv.tv_sec,
-+ tv.tv_usec, lasttv.tv_usec);
-+ /*
-+ * detecting pulse while this
-+ * MUST be a space!
-+ */
-+ sense = sense ? 0 : 1;
-+ }
-+ } else {
-+ data = (int) (deltv*1000000 +
-+ (tv.tv_usec - lasttv.tv_usec));
-+ }
-+ frbwrite(signal^sense ? data : (data|PULSE_BIT));
-+ lasttv = tv;
-+ wake_up_interruptible(&rbuf.wait_poll);
-+ }
-+
-+ return IRQ_HANDLED;
-+}
-+
-+static int is_right_chip(struct gpio_chip *chip, void *data)
-+{
-+ dprintk("is_right_chip %s %d\n", chip->label, strcmp(data, chip->label));
-+
-+ if (strcmp(data, chip->label) == 0)
-+ return 1;
-+ return 0;
-+}
-+
-+static inline int read_bool_property(const struct device_node *np,
-+ const char *propname,
-+ bool *out_value)
-+{
-+ u32 value = 0;
-+ int err = of_property_read_u32(np, propname, &value);
-+ if (err == 0)
-+ *out_value = (value != 0);
-+ return err;
-+}
-+
-+static void read_pin_settings(struct device_node *node)
-+{
-+ u32 pin;
-+ int index;
-+
-+ for (index = 0;
-+ of_property_read_u32_index(
-+ node,
-+ "brcm,pins",
-+ index,
-+ &pin) == 0;
-+ index++) {
-+ u32 function;
-+ int err;
-+ err = of_property_read_u32_index(
-+ node,
-+ "brcm,function",
-+ index,
-+ &function);
-+ if (err == 0) {
-+ if (function == 1) /* Output */
-+ gpio_out_pin = pin;
-+ else if (function == 0) /* Input */
-+ gpio_in_pin = pin;
-+ }
-+ }
-+}
-+
-+static int init_port(void)
-+{
-+ int i, nlow, nhigh;
-+ struct device_node *node;
-+
-+ node = lirc_rpi_dev->dev.of_node;
-+
-+ gpiochip = gpiochip_find("bcm2708_gpio", is_right_chip);
-+
-+ /*
-+ * Because of the lack of a setpull function, only support
-+ * pinctrl-bcm2835 if using device tree.
-+ */
-+ if (!gpiochip && node)
-+ gpiochip = gpiochip_find("pinctrl-bcm2835", is_right_chip);
-+
-+ if (!gpiochip) {
-+ pr_err(LIRC_DRIVER_NAME ": gpio chip not found!\n");
-+ return -ENODEV;
-+ }
-+
-+ if (node) {
-+ struct device_node *pins_node;
-+
-+ pins_node = of_parse_phandle(node, "pinctrl-0", 0);
-+ if (!pins_node) {
-+ printk(KERN_ERR LIRC_DRIVER_NAME
-+ ": pinctrl settings not found!\n");
-+ return -EINVAL;
-+ }
-+
-+ read_pin_settings(pins_node);
-+
-+ of_property_read_u32(node, "rpi,sense", &sense);
-+
-+ read_bool_property(node, "rpi,softcarrier", &softcarrier);
-+
-+ read_bool_property(node, "rpi,invert", &invert);
-+
-+ read_bool_property(node, "rpi,debug", &debug);
-+
-+ } else {
-+ return -EINVAL;
-+ }
-+
-+ gpiochip->set(gpiochip, gpio_out_pin, invert);
-+
-+ irq_num = gpiochip->to_irq(gpiochip, gpio_in_pin);
-+ dprintk("to_irq %d\n", irq_num);
-+
-+ /* if pin is high, then this must be an active low receiver. */
-+ if (sense == -1) {
-+ /* wait 1/2 sec for the power supply */
-+ msleep(500);
-+
-+ /*
-+ * probe 9 times every 0.04s, collect "votes" for
-+ * active high/low
-+ */
-+ nlow = 0;
-+ nhigh = 0;
-+ for (i = 0; i < 9; i++) {
-+ if (gpiochip->get(gpiochip, gpio_in_pin))
-+ nlow++;
-+ else
-+ nhigh++;
-+ msleep(40);
-+ }
-+ sense = (nlow >= nhigh ? 1 : 0);
-+ printk(KERN_INFO LIRC_DRIVER_NAME
-+ ": auto-detected active %s receiver on GPIO pin %d\n",
-+ sense ? "low" : "high", gpio_in_pin);
-+ } else {
-+ printk(KERN_INFO LIRC_DRIVER_NAME
-+ ": manually using active %s receiver on GPIO pin %d\n",
-+ sense ? "low" : "high", gpio_in_pin);
-+ }
-+
-+ return 0;
-+}
-+
-+// called when the character device is opened
-+static int set_use_inc(void *data)
-+{
-+ int result;
-+
-+ /* initialize timestamp */
-+ do_gettimeofday(&lasttv);
-+
-+ result = request_irq(irq_num,
-+ (irq_handler_t) irq_handler,
-+ IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING,
-+ LIRC_DRIVER_NAME, (void*) 0);
-+
-+ switch (result) {
-+ case -EBUSY:
-+ printk(KERN_ERR LIRC_DRIVER_NAME
-+ ": IRQ %d is busy\n",
-+ irq_num);
-+ return -EBUSY;
-+ case -EINVAL:
-+ printk(KERN_ERR LIRC_DRIVER_NAME
-+ ": Bad irq number or handler\n");
-+ return -EINVAL;
-+ default:
-+ dprintk("Interrupt %d obtained\n",
-+ irq_num);
-+ break;
-+ };
-+
-+ /* initialize pulse/space widths */
-+ init_timing_params(duty_cycle, freq);
-+
-+ return 0;
-+}
-+
-+static void set_use_dec(void *data)
-+{
-+ /* GPIO Pin Falling/Rising Edge Detect Disable */
-+ irq_set_irq_type(irq_num, 0);
-+ disable_irq(irq_num);
-+
-+ free_irq(irq_num, (void *) 0);
-+
-+ dprintk(KERN_INFO LIRC_DRIVER_NAME
-+ ": freed IRQ %d\n", irq_num);
-+}
-+
-+static ssize_t lirc_write(struct file *file, const char *buf,
-+ size_t n, loff_t *ppos)
-+{
-+ int i, count;
-+ unsigned long flags;
-+ long delta = 0;
-+ int *wbuf;
-+
-+ count = n / sizeof(int);
-+ if (n % sizeof(int) || count % 2 == 0)
-+ return -EINVAL;
-+ wbuf = memdup_user(buf, n);
-+ if (IS_ERR(wbuf))
-+ return PTR_ERR(wbuf);
-+ spin_lock_irqsave(&lock, flags);
-+
-+ for (i = 0; i < count; i++) {
-+ if (i%2)
-+ send_space(wbuf[i] - delta);
-+ else
-+ delta = send_pulse(wbuf[i]);
-+ }
-+ gpiochip->set(gpiochip, gpio_out_pin, invert);
-+
-+ spin_unlock_irqrestore(&lock, flags);
-+ kfree(wbuf);
-+ return n;
-+}
-+
-+static long lirc_ioctl(struct file *filep, unsigned int cmd, unsigned long arg)
-+{
-+ int result;
-+ __u32 value;
-+
-+ switch (cmd) {
-+ case LIRC_GET_SEND_MODE:
-+ return -ENOIOCTLCMD;
-+ break;
-+
-+ case LIRC_SET_SEND_MODE:
-+ result = get_user(value, (__u32 *) arg);
-+ if (result)
-+ return result;
-+ /* only LIRC_MODE_PULSE supported */
-+ if (value != LIRC_MODE_PULSE)
-+ return -ENOSYS;
-+ break;
-+
-+ case LIRC_GET_LENGTH:
-+ return -ENOSYS;
-+ break;
-+
-+ case LIRC_SET_SEND_DUTY_CYCLE:
-+ dprintk("SET_SEND_DUTY_CYCLE\n");
-+ result = get_user(value, (__u32 *) arg);
-+ if (result)
-+ return result;
-+ if (value <= 0 || value > 100)
-+ return -EINVAL;
-+ return init_timing_params(value, freq);
-+ break;
-+
-+ case LIRC_SET_SEND_CARRIER:
-+ dprintk("SET_SEND_CARRIER\n");
-+ result = get_user(value, (__u32 *) arg);
-+ if (result)
-+ return result;
-+ if (value > 500000 || value < 20000)
-+ return -EINVAL;
-+ return init_timing_params(duty_cycle, value);
-+ break;
-+
-+ default:
-+ return lirc_dev_fop_ioctl(filep, cmd, arg);
-+ }
-+ return 0;
-+}
-+
-+static const struct file_operations lirc_fops = {
-+ .owner = THIS_MODULE,
-+ .write = lirc_write,
-+ .unlocked_ioctl = lirc_ioctl,
-+ .read = lirc_dev_fop_read,
-+ .poll = lirc_dev_fop_poll,
-+ .open = lirc_dev_fop_open,
-+ .release = lirc_dev_fop_close,
-+ .llseek = no_llseek,
-+};
-+
-+static struct lirc_driver driver = {
-+ .name = LIRC_DRIVER_NAME,
-+ .minor = -1,
-+ .code_length = 1,
-+ .sample_rate = 0,
-+ .data = NULL,
-+ .add_to_buf = NULL,
-+ .rbuf = &rbuf,
-+ .set_use_inc = set_use_inc,
-+ .set_use_dec = set_use_dec,
-+ .fops = &lirc_fops,
-+ .dev = NULL,
-+ .owner = THIS_MODULE,
-+};
-+
-+static const struct of_device_id lirc_rpi_of_match[] = {
-+ { .compatible = "rpi,lirc-rpi", },
-+ {},
-+};
-+MODULE_DEVICE_TABLE(of, lirc_rpi_of_match);
-+
-+static struct platform_driver lirc_rpi_driver = {
-+ .driver = {
-+ .name = LIRC_DRIVER_NAME,
-+ .owner = THIS_MODULE,
-+ .of_match_table = of_match_ptr(lirc_rpi_of_match),
-+ },
-+};
-+
-+static int __init lirc_rpi_init(void)
-+{
-+ struct device_node *node;
-+ int result;
-+
-+ /* Init read buffer. */
-+ result = lirc_buffer_init(&rbuf, sizeof(int), RBUF_LEN);
-+ if (result < 0)
-+ return -ENOMEM;
-+
-+ result = platform_driver_register(&lirc_rpi_driver);
-+ if (result) {
-+ printk(KERN_ERR LIRC_DRIVER_NAME
-+ ": lirc register returned %d\n", result);
-+ goto exit_buffer_free;
-+ }
-+
-+ node = of_find_compatible_node(NULL, NULL,
-+ lirc_rpi_of_match[0].compatible);
-+
-+ if (node) {
-+ /* DT-enabled */
-+ lirc_rpi_dev = of_find_device_by_node(node);
-+ WARN_ON(lirc_rpi_dev->dev.of_node != node);
-+ of_node_put(node);
-+ }
-+ else {
-+ lirc_rpi_dev = platform_device_alloc(LIRC_DRIVER_NAME, 0);
-+ if (!lirc_rpi_dev) {
-+ result = -ENOMEM;
-+ goto exit_driver_unregister;
-+ }
-+
-+ result = platform_device_add(lirc_rpi_dev);
-+ if (result)
-+ goto exit_device_put;
-+ }
-+
-+ return 0;
-+
-+ exit_device_put:
-+ platform_device_put(lirc_rpi_dev);
-+
-+ exit_driver_unregister:
-+ platform_driver_unregister(&lirc_rpi_driver);
-+
-+ exit_buffer_free:
-+ lirc_buffer_free(&rbuf);
-+
-+ return result;
-+}
-+
-+static void lirc_rpi_exit(void)
-+{
-+ if (!lirc_rpi_dev->dev.of_node)
-+ platform_device_unregister(lirc_rpi_dev);
-+ platform_driver_unregister(&lirc_rpi_driver);
-+ lirc_buffer_free(&rbuf);
-+}
-+
-+static int __init lirc_rpi_init_module(void)
-+{
-+ int result;
-+
-+ result = lirc_rpi_init();
-+ if (result)
-+ return result;
-+
-+ result = init_port();
-+ if (result < 0)
-+ goto exit_rpi;
-+
-+ driver.features = LIRC_CAN_SET_SEND_DUTY_CYCLE |
-+ LIRC_CAN_SET_SEND_CARRIER |
-+ LIRC_CAN_SEND_PULSE |
-+ LIRC_CAN_REC_MODE2;
-+
-+ driver.dev = &lirc_rpi_dev->dev;
-+ driver.minor = lirc_register_driver(&driver);
-+
-+ if (driver.minor < 0) {
-+ printk(KERN_ERR LIRC_DRIVER_NAME
-+ ": device registration failed with %d\n", result);
-+ result = -EIO;
-+ goto exit_rpi;
-+ }
-+
-+ printk(KERN_INFO LIRC_DRIVER_NAME ": driver registered!\n");
-+
-+ return 0;
-+
-+ exit_rpi:
-+ lirc_rpi_exit();
-+
-+ return result;
-+}
-+
-+static void __exit lirc_rpi_exit_module(void)
-+{
-+ lirc_unregister_driver(driver.minor);
-+
-+ gpio_free(gpio_out_pin);
-+ gpio_free(gpio_in_pin);
-+
-+ lirc_rpi_exit();
-+
-+ printk(KERN_INFO LIRC_DRIVER_NAME ": cleaned up module\n");
-+}
-+
-+module_init(lirc_rpi_init_module);
-+module_exit(lirc_rpi_exit_module);
-+
-+MODULE_DESCRIPTION("Infra-red receiver and blaster driver for Raspberry Pi GPIO.");
-+MODULE_AUTHOR("Aron Robert Szabo <aron at reon.hu>");
-+MODULE_AUTHOR("Michael Bishop <cleverca22 at gmail.com>");
-+MODULE_LICENSE("GPL");
-+
-+module_param(gpio_out_pin, int, S_IRUGO);
-+MODULE_PARM_DESC(gpio_out_pin, "GPIO output/transmitter pin number of the BCM"
-+ " processor. (default 17");
-+
-+module_param(gpio_in_pin, int, S_IRUGO);
-+MODULE_PARM_DESC(gpio_in_pin, "GPIO input pin number of the BCM processor."
-+ " (default 18");
-+
-+module_param(gpio_in_pull, int, S_IRUGO);
-+MODULE_PARM_DESC(gpio_in_pull, "GPIO input pin pull configuration."
-+ " (0 = off, 1 = up, 2 = down, default down)");
-+
-+module_param(sense, int, S_IRUGO);
-+MODULE_PARM_DESC(sense, "Override autodetection of IR receiver circuit"
-+ " (0 = active high, 1 = active low )");
-+
-+module_param(softcarrier, bool, S_IRUGO);
-+MODULE_PARM_DESC(softcarrier, "Software carrier (0 = off, 1 = on, default on)");
-+
-+module_param(invert, bool, S_IRUGO);
-+MODULE_PARM_DESC(invert, "Invert output (0 = off, 1 = on, default off");
-+
-+module_param(debug, bool, S_IRUGO | S_IWUSR);
-+MODULE_PARM_DESC(debug, "Enable debugging messages");
---- /dev/null
-+++ b/include/linux/platform_data/bcm2708.h
-@@ -0,0 +1,23 @@
-+/*
-+ * include/linux/platform_data/bcm2708.h
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ *
-+ * (C) 2014 Julian Scheel <julian at jusst.de>
-+ *
-+ */
-+#ifndef __BCM2708_H_
-+#define __BCM2708_H_
-+
-+typedef enum {
-+ BCM2708_PULL_OFF,
-+ BCM2708_PULL_UP,
-+ BCM2708_PULL_DOWN
-+} bcm2708_gpio_pull_t;
-+
-+extern int bcm2708_gpio_setpull(struct gpio_chip *gc, unsigned offset,
-+ bcm2708_gpio_pull_t value);
-+
-+#endif
diff --git a/target/linux/brcm2708/patches-4.4/0043-Add-cpufreq-driver.patch b/target/linux/brcm2708/patches-4.4/0043-Add-cpufreq-driver.patch
deleted file mode 100644
index 4a76a3a..0000000
--- a/target/linux/brcm2708/patches-4.4/0043-Add-cpufreq-driver.patch
+++ /dev/null
@@ -1,257 +0,0 @@
-From 0dff3fca2aca68c342bffbcfa38101a5a24e5e85 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Wed, 3 Jul 2013 00:49:20 +0100
-Subject: [PATCH] Add cpufreq driver
-
-Signed-off-by: popcornmix <popcornmix at gmail.com>
----
- drivers/cpufreq/Kconfig.arm | 9 ++
- drivers/cpufreq/Makefile | 1 +
- drivers/cpufreq/bcm2835-cpufreq.c | 213 ++++++++++++++++++++++++++++++++++++++
- 3 files changed, 223 insertions(+)
- create mode 100644 drivers/cpufreq/bcm2835-cpufreq.c
-
---- a/drivers/cpufreq/Kconfig.arm
-+++ b/drivers/cpufreq/Kconfig.arm
-@@ -217,6 +217,15 @@ config ARM_SPEAR_CPUFREQ
- help
- This adds the CPUFreq driver support for SPEAr SOCs.
-
-+config ARM_BCM2835_CPUFREQ
-+ depends on RASPBERRYPI_FIRMWARE
-+ bool "BCM2835 Driver"
-+ default y
-+ help
-+ This adds the CPUFreq driver for BCM2835
-+
-+ If in doubt, say N.
-+
- config ARM_TEGRA20_CPUFREQ
- bool "Tegra20 CPUFreq support"
- depends on ARCH_TEGRA
---- a/drivers/cpufreq/Makefile
-+++ b/drivers/cpufreq/Makefile
-@@ -73,6 +73,7 @@ obj-$(CONFIG_ARM_SA1100_CPUFREQ) += sa11
- obj-$(CONFIG_ARM_SA1110_CPUFREQ) += sa1110-cpufreq.o
- obj-$(CONFIG_ARM_SCPI_CPUFREQ) += scpi-cpufreq.o
- obj-$(CONFIG_ARM_SPEAR_CPUFREQ) += spear-cpufreq.o
-+obj-$(CONFIG_ARM_BCM2835_CPUFREQ) += bcm2835-cpufreq.o
- obj-$(CONFIG_ARM_TEGRA20_CPUFREQ) += tegra20-cpufreq.o
- obj-$(CONFIG_ARM_TEGRA124_CPUFREQ) += tegra124-cpufreq.o
- obj-$(CONFIG_ARM_VEXPRESS_SPC_CPUFREQ) += vexpress-spc-cpufreq.o
---- /dev/null
-+++ b/drivers/cpufreq/bcm2835-cpufreq.c
-@@ -0,0 +1,213 @@
-+/*****************************************************************************
-+* Copyright 2011 Broadcom Corporation. All rights reserved.
-+*
-+* Unless you and Broadcom execute a separate written software license
-+* agreement governing use of this software, this software is licensed to you
-+* under the terms of the GNU General Public License version 2, available at
-+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
-+*
-+* Notwithstanding the above, under no circumstances may you combine this
-+* software in any way with any other Broadcom software provided under a
-+* license other than the GPL, without Broadcom's express prior written
-+* consent.
-+*****************************************************************************/
-+
-+/*****************************************************************************
-+* FILENAME: bcm2835-cpufreq.h
-+* DESCRIPTION: This driver dynamically manages the CPU Frequency of the ARM
-+* processor. Messages are sent to Videocore either setting or requesting the
-+* frequency of the ARM in order to match an appropiate frequency to the current
-+* usage of the processor. The policy which selects the frequency to use is
-+* defined in the kernel .config file, but can be changed during runtime.
-+*****************************************************************************/
-+
-+/* ---------- INCLUDES ---------- */
-+#include <linux/kernel.h>
-+#include <linux/init.h>
-+#include <linux/module.h>
-+#include <linux/cpufreq.h>
-+#include <soc/bcm2835/raspberrypi-firmware.h>
-+
-+/* ---------- DEFINES ---------- */
-+/*#define CPUFREQ_DEBUG_ENABLE*/ /* enable debugging */
-+#define MODULE_NAME "bcm2835-cpufreq"
-+
-+#define VCMSG_ID_ARM_CLOCK 0x000000003 /* Clock/Voltage ID's */
-+
-+/* debug printk macros */
-+#ifdef CPUFREQ_DEBUG_ENABLE
-+#define print_debug(fmt,...) pr_debug("%s:%s:%d: "fmt, MODULE_NAME, __func__, __LINE__, ##__VA_ARGS__)
-+#else
-+#define print_debug(fmt,...)
-+#endif
-+#define print_err(fmt,...) pr_err("%s:%s:%d: "fmt, MODULE_NAME, __func__,__LINE__, ##__VA_ARGS__)
-+#define print_info(fmt,...) pr_info("%s: "fmt, MODULE_NAME, ##__VA_ARGS__)
-+
-+/* ---------- GLOBALS ---------- */
-+static struct cpufreq_driver bcm2835_cpufreq_driver; /* the cpufreq driver global */
-+
-+static struct cpufreq_frequency_table bcm2835_freq_table[] = {
-+ {0, 0, 0},
-+ {0, 0, 0},
-+ {0, 0, CPUFREQ_TABLE_END},
-+};
-+
-+/*
-+ ===============================================
-+ clk_rate either gets or sets the clock rates.
-+ ===============================================
-+*/
-+
-+static int bcm2835_cpufreq_clock_property(u32 tag, u32 id, u32 *val)
-+{
-+ struct rpi_firmware *fw = rpi_firmware_get(NULL);
-+ struct {
-+ u32 id;
-+ u32 val;
-+ } packet;
-+ int ret;
-+
-+ packet.id = id;
-+ packet.val = *val;
-+ ret = rpi_firmware_property(fw, tag, &packet, sizeof(packet));
-+ if (ret)
-+ return ret;
-+
-+ *val = packet.val;
-+
-+ return 0;
-+}
-+
-+static uint32_t bcm2835_cpufreq_set_clock(int cur_rate, int arm_rate)
-+{
-+ u32 rate = arm_rate * 1000;
-+ int ret;
-+
-+ ret = bcm2835_cpufreq_clock_property(RPI_FIRMWARE_SET_CLOCK_RATE, VCMSG_ID_ARM_CLOCK, &rate);
-+ if (ret) {
-+ print_err("Failed to set clock: %d (%d)\n", arm_rate, ret);
-+ return 0;
-+ }
-+
-+ rate /= 1000;
-+ print_debug("Setting new frequency = %d -> %d (actual %d)\n", cur_rate, arm_rate, rate);
-+
-+ return rate;
-+}
-+
-+static uint32_t bcm2835_cpufreq_get_clock(int tag)
-+{
-+ u32 rate;
-+ int ret;
-+
-+ ret = bcm2835_cpufreq_clock_property(tag, VCMSG_ID_ARM_CLOCK, &rate);
-+ if (ret) {
-+ print_err("Failed to get clock (%d)\n", ret);
-+ return 0;
-+ }
-+
-+ rate /= 1000;
-+ print_debug("%s frequency = %u\n",
-+ tag == RPI_FIRMWARE_GET_CLOCK_RATE ? "Current":
-+ tag == RPI_FIRMWARE_GET_MIN_CLOCK_RATE ? "Min":
-+ tag == RPI_FIRMWARE_GET_MAX_CLOCK_RATE ? "Max":
-+ "Unexpected", rate);
-+
-+ return rate;
-+}
-+
-+/*
-+ ====================================================
-+ Module Initialisation registers the cpufreq driver
-+ ====================================================
-+*/
-+static int __init bcm2835_cpufreq_module_init(void)
-+{
-+ print_debug("IN\n");
-+ return cpufreq_register_driver(&bcm2835_cpufreq_driver);
-+}
-+
-+/*
-+ =============
-+ Module exit
-+ =============
-+*/
-+static void __exit bcm2835_cpufreq_module_exit(void)
-+{
-+ print_debug("IN\n");
-+ cpufreq_unregister_driver(&bcm2835_cpufreq_driver);
-+ return;
-+}
-+
-+/*
-+ ==============================================================
-+ Initialisation function sets up the CPU policy for first use
-+ ==============================================================
-+*/
-+static int bcm2835_cpufreq_driver_init(struct cpufreq_policy *policy)
-+{
-+ /* measured value of how long it takes to change frequency */
-+ const unsigned int transition_latency = 355000; /* ns */
-+
-+ if (!rpi_firmware_get(NULL)) {
-+ print_err("Firmware is not available\n");
-+ return -ENODEV;
-+ }
-+
-+ /* now find out what the maximum and minimum frequencies are */
-+ bcm2835_freq_table[0].frequency = bcm2835_cpufreq_get_clock(RPI_FIRMWARE_GET_MIN_CLOCK_RATE);
-+ bcm2835_freq_table[1].frequency = bcm2835_cpufreq_get_clock(RPI_FIRMWARE_GET_MAX_CLOCK_RATE);
-+
-+ print_info("min=%d max=%d\n", bcm2835_freq_table[0].frequency, bcm2835_freq_table[1].frequency);
-+ return cpufreq_generic_init(policy, bcm2835_freq_table, transition_latency);
-+}
-+
-+/*
-+ =====================================================================
-+ Target index function chooses the requested frequency from the table
-+ =====================================================================
-+*/
-+
-+static int bcm2835_cpufreq_driver_target_index(struct cpufreq_policy *policy, unsigned int state)
-+{
-+ unsigned int target_freq = bcm2835_freq_table[state].frequency;
-+ unsigned int cur = bcm2835_cpufreq_set_clock(policy->cur, target_freq);
-+
-+ if (!cur)
-+ {
-+ print_err("Error occurred setting a new frequency (%d)\n", target_freq);
-+ return -EINVAL;
-+ }
-+ print_debug("%s: %i: freq %d->%d\n", policy->governor->name, state, policy->cur, cur);
-+ return 0;
-+}
-+
-+/*
-+ ======================================================
-+ Get function returns the current frequency from table
-+ ======================================================
-+*/
-+
-+static unsigned int bcm2835_cpufreq_driver_get(unsigned int cpu)
-+{
-+ unsigned int actual_rate = bcm2835_cpufreq_get_clock(RPI_FIRMWARE_GET_CLOCK_RATE);
-+ print_debug("cpu%d: freq=%d\n", cpu, actual_rate);
-+ return actual_rate <= bcm2835_freq_table[0].frequency ? bcm2835_freq_table[0].frequency : bcm2835_freq_table[1].frequency;
-+}
-+
-+/* the CPUFreq driver */
-+static struct cpufreq_driver bcm2835_cpufreq_driver = {
-+ .name = "BCM2835 CPUFreq",
-+ .init = bcm2835_cpufreq_driver_init,
-+ .verify = cpufreq_generic_frequency_table_verify,
-+ .target_index = bcm2835_cpufreq_driver_target_index,
-+ .get = bcm2835_cpufreq_driver_get,
-+ .attr = cpufreq_generic_attr,
-+};
-+
-+MODULE_AUTHOR("Dorian Peake and Dom Cobley");
-+MODULE_DESCRIPTION("CPU frequency driver for BCM2835 chip");
-+MODULE_LICENSE("GPL");
-+
-+module_init(bcm2835_cpufreq_module_init);
-+module_exit(bcm2835_cpufreq_module_exit);
diff --git a/target/linux/brcm2708/patches-4.4/0044-Added-hwmon-thermal-driver-for-reporting-core-temper.patch b/target/linux/brcm2708/patches-4.4/0044-Added-hwmon-thermal-driver-for-reporting-core-temper.patch
deleted file mode 100644
index e22482c..0000000
--- a/target/linux/brcm2708/patches-4.4/0044-Added-hwmon-thermal-driver-for-reporting-core-temper.patch
+++ /dev/null
@@ -1,193 +0,0 @@
-From a567aafda2f0d7742253f40e65dee98eeea0e18d Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Tue, 26 Mar 2013 19:24:24 +0000
-Subject: [PATCH] Added hwmon/thermal driver for reporting core temperature.
- Thanks Dorian
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-BCM270x: Move thermal sensor to Device Tree
-
-Add Device Tree support to bcm2835-thermal driver.
-Add thermal sensor device to Device Tree.
-Don't add platform device when booting in DT mode.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
----
- drivers/thermal/Kconfig | 7 ++
- drivers/thermal/Makefile | 1 +
- drivers/thermal/bcm2835-thermal.c | 141 ++++++++++++++++++++++++++++++++++++++
- 3 files changed, 149 insertions(+)
- create mode 100644 drivers/thermal/bcm2835-thermal.c
-
---- a/drivers/thermal/Kconfig
-+++ b/drivers/thermal/Kconfig
-@@ -285,6 +285,13 @@ config INTEL_POWERCLAMP
- enforce idle time which results in more package C-state residency. The
- user interface is exposed via generic thermal framework.
-
-+config THERMAL_BCM2835
-+ depends on RASPBERRYPI_FIRMWARE
-+ tristate "BCM2835 Thermal Driver"
-+ help
-+ This will enable temperature monitoring for the Broadcom BCM2835
-+ chip. If built as a module, it will be called 'bcm2835-thermal'.
-+
- config X86_PKG_TEMP_THERMAL
- tristate "X86 package temperature thermal driver"
- depends on X86_THERMAL_VECTOR
---- a/drivers/thermal/Makefile
-+++ b/drivers/thermal/Makefile
-@@ -38,6 +38,7 @@ obj-$(CONFIG_ARMADA_THERMAL) += armada_t
- obj-$(CONFIG_IMX_THERMAL) += imx_thermal.o
- obj-$(CONFIG_DB8500_CPUFREQ_COOLING) += db8500_cpufreq_cooling.o
- obj-$(CONFIG_INTEL_POWERCLAMP) += intel_powerclamp.o
-+obj-$(CONFIG_THERMAL_BCM2835) += bcm2835-thermal.o
- obj-$(CONFIG_X86_PKG_TEMP_THERMAL) += x86_pkg_temp_thermal.o
- obj-$(CONFIG_INTEL_SOC_DTS_IOSF_CORE) += intel_soc_dts_iosf.o
- obj-$(CONFIG_INTEL_SOC_DTS_THERMAL) += intel_soc_dts_thermal.o
---- /dev/null
-+++ b/drivers/thermal/bcm2835-thermal.c
-@@ -0,0 +1,141 @@
-+/*****************************************************************************
-+* Copyright 2011 Broadcom Corporation. All rights reserved.
-+*
-+* Unless you and Broadcom execute a separate written software license
-+* agreement governing use of this software, this software is licensed to you
-+* under the terms of the GNU General Public License version 2, available at
-+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
-+*
-+* Notwithstanding the above, under no circumstances may you combine this
-+* software in any way with any other Broadcom software provided under a
-+* license other than the GPL, without Broadcom's express prior written
-+* consent.
-+*****************************************************************************/
-+
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+#include <linux/thermal.h>
-+#include <soc/bcm2835/raspberrypi-firmware.h>
-+
-+static int bcm2835_thermal_get_property(struct thermal_zone_device *tz,
-+ int *temp, u32 tag)
-+{
-+ struct rpi_firmware *fw = tz->devdata;
-+ struct {
-+ u32 id;
-+ u32 val;
-+ } packet;
-+ int ret;
-+
-+ *temp = 0;
-+ packet.id = 0;
-+ ret = rpi_firmware_property(fw, tag, &packet, sizeof(packet));
-+ if (ret) {
-+ dev_err(&tz->device, "Failed to get temperature\n");
-+ return ret;
-+ }
-+
-+ *temp = packet.val;
-+ dev_dbg(&tz->device, "%stemp=%d\n",
-+ tag == RPI_FIRMWARE_GET_MAX_TEMPERATURE ? "max" : "", *temp);
-+
-+ return 0;
-+}
-+
-+static int bcm2835_thermal_get_temp(struct thermal_zone_device *tz,
-+ int *temp)
-+{
-+ return bcm2835_thermal_get_property(tz, temp,
-+ RPI_FIRMWARE_GET_TEMPERATURE);
-+}
-+
-+static int bcm2835_thermal_get_max_temp(struct thermal_zone_device *tz,
-+ int trip, int *temp)
-+{
-+ /*
-+ * The maximum safe temperature of the SoC.
-+ * Overclock may be disabled above this temperature.
-+ */
-+ return bcm2835_thermal_get_property(tz, temp,
-+ RPI_FIRMWARE_GET_MAX_TEMPERATURE);
-+}
-+
-+static int bcm2835_thermal_get_trip_type(struct thermal_zone_device *tz,
-+ int trip, enum thermal_trip_type *type)
-+{
-+ *type = THERMAL_TRIP_HOT;
-+
-+ return 0;
-+}
-+
-+static int bcm2835_thermal_get_mode(struct thermal_zone_device *tz,
-+ enum thermal_device_mode *mode)
-+{
-+ *mode = THERMAL_DEVICE_ENABLED;
-+
-+ return 0;
-+}
-+
-+static struct thermal_zone_device_ops ops = {
-+ .get_temp = bcm2835_thermal_get_temp,
-+ .get_trip_temp = bcm2835_thermal_get_max_temp,
-+ .get_trip_type = bcm2835_thermal_get_trip_type,
-+ .get_mode = bcm2835_thermal_get_mode,
-+};
-+
-+static int bcm2835_thermal_probe(struct platform_device *pdev)
-+{
-+ struct device_node *fw_np;
-+ struct rpi_firmware *fw;
-+ struct thermal_zone_device *tz;
-+
-+ fw_np = of_parse_phandle(pdev->dev.of_node, "firmware", 0);
-+/* Remove comment when booting without Device Tree is no longer supported
-+ if (!fw_np) {
-+ dev_err(&pdev->dev, "Missing firmware node\n");
-+ return -ENOENT;
-+ }
-+*/
-+ fw = rpi_firmware_get(fw_np);
-+ if (!fw)
-+ return -EPROBE_DEFER;
-+
-+ tz = thermal_zone_device_register("bcm2835_thermal", 1, 0, fw, &ops,
-+ NULL, 0, 0);
-+ if (IS_ERR(tz)) {
-+ dev_err(&pdev->dev, "Failed to register the thermal device\n");
-+ return PTR_ERR(tz);
-+ }
-+
-+ platform_set_drvdata(pdev, tz);
-+
-+ return 0;
-+}
-+
-+static int bcm2835_thermal_remove(struct platform_device *pdev)
-+{
-+ thermal_zone_device_unregister(platform_get_drvdata(pdev));
-+
-+ return 0;
-+}
-+
-+static const struct of_device_id bcm2835_thermal_of_match_table[] = {
-+ { .compatible = "brcm,bcm2835-thermal", },
-+ {},
-+};
-+MODULE_DEVICE_TABLE(of, bcm2835_thermal_of_match_table);
-+
-+static struct platform_driver bcm2835_thermal_driver = {
-+ .probe = bcm2835_thermal_probe,
-+ .remove = bcm2835_thermal_remove,
-+ .driver = {
-+ .name = "bcm2835_thermal",
-+ .of_match_table = bcm2835_thermal_of_match_table,
-+ },
-+};
-+module_platform_driver(bcm2835_thermal_driver);
-+
-+MODULE_AUTHOR("Dorian Peake");
-+MODULE_AUTHOR("Noralf Trønnes");
-+MODULE_DESCRIPTION("Thermal driver for bcm2835 chip");
-+MODULE_LICENSE("GPL");
diff --git a/target/linux/brcm2708/patches-4.4/0045-Add-Chris-Boot-s-i2c-driver.patch b/target/linux/brcm2708/patches-4.4/0045-Add-Chris-Boot-s-i2c-driver.patch
deleted file mode 100644
index e549dd9..0000000
--- a/target/linux/brcm2708/patches-4.4/0045-Add-Chris-Boot-s-i2c-driver.patch
+++ /dev/null
@@ -1,635 +0,0 @@
-From 01586aecc37865acf703736232f1e399c39eea88 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Wed, 17 Jun 2015 15:44:08 +0100
-Subject: [PATCH] Add Chris Boot's i2c driver
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-i2c-bcm2708: fixed baudrate
-
-Fixed issue where the wrong CDIV value was set for baudrates below 3815 Hz (for 250MHz bus clock).
-In that case the computed CDIV value was more than 0xffff. However the CDIV register width is only 16 bits.
-This resulted in incorrect setting of CDIV and higher baudrate than intended.
-Example: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0x1704 -> 42430Hz
-After correction: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0xffff -> 3815Hz
-The correct baudrate is shown in the log after the cdiv > 0xffff correction.
-
-Perform I2C combined transactions when possible
-
-Perform I2C combined transactions whenever possible, within the
-restrictions of the Broadcomm Serial Controller.
-
-Disable DONE interrupt during TA poll
-
-Prevent interrupt from being triggered if poll is missed and transfer
-starts and finishes.
-
-i2c: Make combined transactions optional and disabled by default
-
-i2c: bcm2708: add device tree support
-
-Add DT support to driver and add to .dtsi file.
-Setup pins in .dts file.
-i2c is disabled by default.
-
-Signed-off-by: Noralf Tronnes <notro at tronnes.org>
-
-bcm2708: don't register i2c controllers when using DT
-
-The devices for the i2c controllers are in the Device Tree.
-Only register devices when not using DT.
-
-Signed-off-by: Noralf Tronnes <notro at tronnes.org>
-
-I2C: Only register the I2C device for the current board revision
-
-i2c_bcm2708: Fix clock reference counting
-
-Fix grabbing lock from atomic context in i2c driver
-
-2 main changes:
-- check for timeouts in the bcm2708_bsc_setup function as indicated by this comment:
- /* poll for transfer start bit (should only take 1-20 polls) */
- This implies that the setup function can now fail so account for this everywhere it's called
-- Removed the clk_get_rate call from inside the setup function as it locks a mutex and that's not ok since we call it from under a spin lock.
-
-i2c-bcm2708: When using DT, leave the GPIO setup to pinctrl
-
-i2c-bcm2708: Increase timeouts to allow larger transfers
-
-Use the timeout value provided by the I2C_TIMEOUT ioctl when waiting
-for completion. The default timeout is 1 second.
-
-See: https://github.com/raspberrypi/linux/issues/260
-
-i2c-bcm2708/BCM270X_DT: Add support for I2C2
-
-The third I2C bus (I2C2) is normally reserved for HDMI use. Careless
-use of this bus can break an attached display - use with caution.
-
-It is recommended to disable accesses by VideoCore by setting
-hdmi_ignore_edid=1 or hdmi_edid_file=1 in config.txt.
-
-The interface is disabled by default - enable using the
-i2c2_iknowwhatimdoing DT parameter.
-
-bcm2708-spi: Don't use static pin configuration with DT
-
-Also remove superfluous error checking - the SPI framework ensures the
-validity of the chip_select value.
-
-i2c-bcm2708: Remove non-DT support
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
----
- drivers/i2c/busses/Kconfig | 21 +-
- drivers/i2c/busses/Makefile | 2 +
- drivers/i2c/busses/i2c-bcm2708.c | 493 +++++++++++++++++++++++++++++++++++++++
- 3 files changed, 515 insertions(+), 1 deletion(-)
- create mode 100644 drivers/i2c/busses/i2c-bcm2708.c
-
---- a/drivers/i2c/busses/Kconfig
-+++ b/drivers/i2c/busses/Kconfig
-@@ -8,6 +8,25 @@ menu "I2C Hardware Bus support"
- comment "PC SMBus host controller drivers"
- depends on PCI
-
-+config I2C_BCM2708
-+ tristate "BCM2708 BSC"
-+ depends on MACH_BCM2708 || MACH_BCM2709 || ARCH_BCM2835
-+ help
-+ Enabling this option will add BSC (Broadcom Serial Controller)
-+ support for the BCM2708. BSC is a Broadcom proprietary bus compatible
-+ with I2C/TWI/SMBus.
-+
-+config I2C_BCM2708_BAUDRATE
-+ prompt "BCM2708 I2C baudrate"
-+ depends on I2C_BCM2708
-+ int
-+ default 100000
-+ help
-+ Set the I2C baudrate. This will alter the default value. A
-+ different baudrate can be set by using a module parameter as well. If
-+ no parameter is provided when loading, this is the value that will be
-+ used.
-+
- config I2C_ALI1535
- tristate "ALI 1535"
- depends on PCI
-@@ -365,7 +384,7 @@ config I2C_AXXIA
-
- config I2C_BCM2835
- tristate "Broadcom BCM2835 I2C controller"
-- depends on ARCH_BCM2835
-+ depends on ARCH_BCM2835 || ARCH_BCM2708 || ARCH_BCM2709
- help
- If you say yes to this option, support will be included for the
- BCM2835 I2C controller.
---- a/drivers/i2c/busses/Makefile
-+++ b/drivers/i2c/busses/Makefile
-@@ -2,6 +2,8 @@
- # Makefile for the i2c bus drivers.
- #
-
-+obj-$(CONFIG_I2C_BCM2708) += i2c-bcm2708.o
-+
- # ACPI drivers
- obj-$(CONFIG_I2C_SCMI) += i2c-scmi.o
-
---- /dev/null
-+++ b/drivers/i2c/busses/i2c-bcm2708.c
-@@ -0,0 +1,493 @@
-+/*
-+ * Driver for Broadcom BCM2708 BSC Controllers
-+ *
-+ * Copyright (C) 2012 Chris Boot & Frank Buss
-+ *
-+ * This driver is inspired by:
-+ * i2c-ocores.c, by Peter Korsgaard <jacmet at sunsite.dk>
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+#include <linux/spinlock.h>
-+#include <linux/clk.h>
-+#include <linux/err.h>
-+#include <linux/of.h>
-+#include <linux/platform_device.h>
-+#include <linux/io.h>
-+#include <linux/slab.h>
-+#include <linux/i2c.h>
-+#include <linux/interrupt.h>
-+#include <linux/sched.h>
-+#include <linux/wait.h>
-+
-+/* BSC register offsets */
-+#define BSC_C 0x00
-+#define BSC_S 0x04
-+#define BSC_DLEN 0x08
-+#define BSC_A 0x0c
-+#define BSC_FIFO 0x10
-+#define BSC_DIV 0x14
-+#define BSC_DEL 0x18
-+#define BSC_CLKT 0x1c
-+
-+/* Bitfields in BSC_C */
-+#define BSC_C_I2CEN 0x00008000
-+#define BSC_C_INTR 0x00000400
-+#define BSC_C_INTT 0x00000200
-+#define BSC_C_INTD 0x00000100
-+#define BSC_C_ST 0x00000080
-+#define BSC_C_CLEAR_1 0x00000020
-+#define BSC_C_CLEAR_2 0x00000010
-+#define BSC_C_READ 0x00000001
-+
-+/* Bitfields in BSC_S */
-+#define BSC_S_CLKT 0x00000200
-+#define BSC_S_ERR 0x00000100
-+#define BSC_S_RXF 0x00000080
-+#define BSC_S_TXE 0x00000040
-+#define BSC_S_RXD 0x00000020
-+#define BSC_S_TXD 0x00000010
-+#define BSC_S_RXR 0x00000008
-+#define BSC_S_TXW 0x00000004
-+#define BSC_S_DONE 0x00000002
-+#define BSC_S_TA 0x00000001
-+
-+#define I2C_WAIT_LOOP_COUNT 200
-+
-+#define DRV_NAME "bcm2708_i2c"
-+
-+static unsigned int baudrate = CONFIG_I2C_BCM2708_BAUDRATE;
-+module_param(baudrate, uint, S_IRUSR | S_IWUSR | S_IRGRP | S_IWGRP);
-+MODULE_PARM_DESC(baudrate, "The I2C baudrate");
-+
-+static bool combined = false;
-+module_param(combined, bool, 0644);
-+MODULE_PARM_DESC(combined, "Use combined transactions");
-+
-+struct bcm2708_i2c {
-+ struct i2c_adapter adapter;
-+
-+ spinlock_t lock;
-+ void __iomem *base;
-+ int irq;
-+ struct clk *clk;
-+ u32 cdiv;
-+
-+ struct completion done;
-+
-+ struct i2c_msg *msg;
-+ int pos;
-+ int nmsgs;
-+ bool error;
-+};
-+
-+static inline u32 bcm2708_rd(struct bcm2708_i2c *bi, unsigned reg)
-+{
-+ return readl(bi->base + reg);
-+}
-+
-+static inline void bcm2708_wr(struct bcm2708_i2c *bi, unsigned reg, u32 val)
-+{
-+ writel(val, bi->base + reg);
-+}
-+
-+static inline void bcm2708_bsc_reset(struct bcm2708_i2c *bi)
-+{
-+ bcm2708_wr(bi, BSC_C, 0);
-+ bcm2708_wr(bi, BSC_S, BSC_S_CLKT | BSC_S_ERR | BSC_S_DONE);
-+}
-+
-+static inline void bcm2708_bsc_fifo_drain(struct bcm2708_i2c *bi)
-+{
-+ while ((bcm2708_rd(bi, BSC_S) & BSC_S_RXD) && (bi->pos < bi->msg->len))
-+ bi->msg->buf[bi->pos++] = bcm2708_rd(bi, BSC_FIFO);
-+}
-+
-+static inline void bcm2708_bsc_fifo_fill(struct bcm2708_i2c *bi)
-+{
-+ while ((bcm2708_rd(bi, BSC_S) & BSC_S_TXD) && (bi->pos < bi->msg->len))
-+ bcm2708_wr(bi, BSC_FIFO, bi->msg->buf[bi->pos++]);
-+}
-+
-+static inline int bcm2708_bsc_setup(struct bcm2708_i2c *bi)
-+{
-+ u32 cdiv, s;
-+ u32 c = BSC_C_I2CEN | BSC_C_INTD | BSC_C_ST | BSC_C_CLEAR_1;
-+ int wait_loops = I2C_WAIT_LOOP_COUNT;
-+
-+ /* Can't call clk_get_rate as it locks a mutex and here we are spinlocked.
-+ * Use the value that we cached in the probe.
-+ */
-+ cdiv = bi->cdiv;
-+
-+ if (bi->msg->flags & I2C_M_RD)
-+ c |= BSC_C_INTR | BSC_C_READ;
-+ else
-+ c |= BSC_C_INTT;
-+
-+ bcm2708_wr(bi, BSC_DIV, cdiv);
-+ bcm2708_wr(bi, BSC_A, bi->msg->addr);
-+ bcm2708_wr(bi, BSC_DLEN, bi->msg->len);
-+ if (combined)
-+ {
-+ /* Do the next two messages meet combined transaction criteria?
-+ - Current message is a write, next message is a read
-+ - Both messages to same slave address
-+ - Write message can fit inside FIFO (16 bytes or less) */
-+ if ( (bi->nmsgs > 1) &&
-+ !(bi->msg[0].flags & I2C_M_RD) && (bi->msg[1].flags & I2C_M_RD) &&
-+ (bi->msg[0].addr == bi->msg[1].addr) && (bi->msg[0].len <= 16)) {
-+ /* Fill FIFO with entire write message (16 byte FIFO) */
-+ while (bi->pos < bi->msg->len) {
-+ bcm2708_wr(bi, BSC_FIFO, bi->msg->buf[bi->pos++]);
-+ }
-+ /* Start write transfer (no interrupts, don't clear FIFO) */
-+ bcm2708_wr(bi, BSC_C, BSC_C_I2CEN | BSC_C_ST);
-+
-+ /* poll for transfer start bit (should only take 1-20 polls) */
-+ do {
-+ s = bcm2708_rd(bi, BSC_S);
-+ } while (!(s & (BSC_S_TA | BSC_S_ERR | BSC_S_CLKT | BSC_S_DONE)) && --wait_loops >= 0);
-+
-+ /* did we time out or some error occured? */
-+ if (wait_loops < 0 || (s & (BSC_S_ERR | BSC_S_CLKT))) {
-+ return -1;
-+ }
-+
-+ /* Send next read message before the write transfer finishes. */
-+ bi->nmsgs--;
-+ bi->msg++;
-+ bi->pos = 0;
-+ bcm2708_wr(bi, BSC_DLEN, bi->msg->len);
-+ c = BSC_C_I2CEN | BSC_C_INTD | BSC_C_INTR | BSC_C_ST | BSC_C_READ;
-+ }
-+ }
-+ bcm2708_wr(bi, BSC_C, c);
-+
-+ return 0;
-+}
-+
-+static irqreturn_t bcm2708_i2c_interrupt(int irq, void *dev_id)
-+{
-+ struct bcm2708_i2c *bi = dev_id;
-+ bool handled = true;
-+ u32 s;
-+ int ret;
-+
-+ spin_lock(&bi->lock);
-+
-+ /* we may see camera interrupts on the "other" I2C channel
-+ Just return if we've not sent anything */
-+ if (!bi->nmsgs || !bi->msg) {
-+ goto early_exit;
-+ }
-+
-+ s = bcm2708_rd(bi, BSC_S);
-+
-+ if (s & (BSC_S_CLKT | BSC_S_ERR)) {
-+ bcm2708_bsc_reset(bi);
-+ bi->error = true;
-+
-+ bi->msg = 0; /* to inform the that all work is done */
-+ bi->nmsgs = 0;
-+ /* wake up our bh */
-+ complete(&bi->done);
-+ } else if (s & BSC_S_DONE) {
-+ bi->nmsgs--;
-+
-+ if (bi->msg->flags & I2C_M_RD) {
-+ bcm2708_bsc_fifo_drain(bi);
-+ }
-+
-+ bcm2708_bsc_reset(bi);
-+
-+ if (bi->nmsgs) {
-+ /* advance to next message */
-+ bi->msg++;
-+ bi->pos = 0;
-+ ret = bcm2708_bsc_setup(bi);
-+ if (ret < 0) {
-+ bcm2708_bsc_reset(bi);
-+ bi->error = true;
-+ bi->msg = 0; /* to inform the that all work is done */
-+ bi->nmsgs = 0;
-+ /* wake up our bh */
-+ complete(&bi->done);
-+ goto early_exit;
-+ }
-+ } else {
-+ bi->msg = 0; /* to inform the that all work is done */
-+ bi->nmsgs = 0;
-+ /* wake up our bh */
-+ complete(&bi->done);
-+ }
-+ } else if (s & BSC_S_TXW) {
-+ bcm2708_bsc_fifo_fill(bi);
-+ } else if (s & BSC_S_RXR) {
-+ bcm2708_bsc_fifo_drain(bi);
-+ } else {
-+ handled = false;
-+ }
-+
-+early_exit:
-+ spin_unlock(&bi->lock);
-+
-+ return handled ? IRQ_HANDLED : IRQ_NONE;
-+}
-+
-+static int bcm2708_i2c_master_xfer(struct i2c_adapter *adap,
-+ struct i2c_msg *msgs, int num)
-+{
-+ struct bcm2708_i2c *bi = adap->algo_data;
-+ unsigned long flags;
-+ int ret;
-+
-+ spin_lock_irqsave(&bi->lock, flags);
-+
-+ reinit_completion(&bi->done);
-+ bi->msg = msgs;
-+ bi->pos = 0;
-+ bi->nmsgs = num;
-+ bi->error = false;
-+
-+ ret = bcm2708_bsc_setup(bi);
-+
-+ spin_unlock_irqrestore(&bi->lock, flags);
-+
-+ /* check the result of the setup */
-+ if (ret < 0)
-+ {
-+ dev_err(&adap->dev, "transfer setup timed out\n");
-+ goto error_timeout;
-+ }
-+
-+ ret = wait_for_completion_timeout(&bi->done, adap->timeout);
-+ if (ret == 0) {
-+ dev_err(&adap->dev, "transfer timed out\n");
-+ goto error_timeout;
-+ }
-+
-+ ret = bi->error ? -EIO : num;
-+ return ret;
-+
-+error_timeout:
-+ spin_lock_irqsave(&bi->lock, flags);
-+ bcm2708_bsc_reset(bi);
-+ bi->msg = 0; /* to inform the interrupt handler that there's nothing else to be done */
-+ bi->nmsgs = 0;
-+ spin_unlock_irqrestore(&bi->lock, flags);
-+ return -ETIMEDOUT;
-+}
-+
-+static u32 bcm2708_i2c_functionality(struct i2c_adapter *adap)
-+{
-+ return I2C_FUNC_I2C | /*I2C_FUNC_10BIT_ADDR |*/ I2C_FUNC_SMBUS_EMUL;
-+}
-+
-+static struct i2c_algorithm bcm2708_i2c_algorithm = {
-+ .master_xfer = bcm2708_i2c_master_xfer,
-+ .functionality = bcm2708_i2c_functionality,
-+};
-+
-+static int bcm2708_i2c_probe(struct platform_device *pdev)
-+{
-+ struct resource *regs;
-+ int irq, err = -ENOMEM;
-+ struct clk *clk;
-+ struct bcm2708_i2c *bi;
-+ struct i2c_adapter *adap;
-+ unsigned long bus_hz;
-+ u32 cdiv;
-+
-+ if (pdev->dev.of_node) {
-+ u32 bus_clk_rate;
-+ pdev->id = of_alias_get_id(pdev->dev.of_node, "i2c");
-+ if (pdev->id < 0) {
-+ dev_err(&pdev->dev, "alias is missing\n");
-+ return -EINVAL;
-+ }
-+ if (!of_property_read_u32(pdev->dev.of_node,
-+ "clock-frequency", &bus_clk_rate))
-+ baudrate = bus_clk_rate;
-+ else
-+ dev_warn(&pdev->dev,
-+ "Could not read clock-frequency property\n");
-+ }
-+
-+ regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+ if (!regs) {
-+ dev_err(&pdev->dev, "could not get IO memory\n");
-+ return -ENXIO;
-+ }
-+
-+ irq = platform_get_irq(pdev, 0);
-+ if (irq < 0) {
-+ dev_err(&pdev->dev, "could not get IRQ\n");
-+ return irq;
-+ }
-+
-+ clk = clk_get(&pdev->dev, NULL);
-+ if (IS_ERR(clk)) {
-+ dev_err(&pdev->dev, "could not find clk: %ld\n", PTR_ERR(clk));
-+ return PTR_ERR(clk);
-+ }
-+
-+ err = clk_prepare_enable(clk);
-+ if (err) {
-+ dev_err(&pdev->dev, "could not enable clk: %d\n", err);
-+ goto out_clk_put;
-+ }
-+
-+ bi = kzalloc(sizeof(*bi), GFP_KERNEL);
-+ if (!bi)
-+ goto out_clk_disable;
-+
-+ platform_set_drvdata(pdev, bi);
-+
-+ adap = &bi->adapter;
-+ adap->class = I2C_CLASS_HWMON | I2C_CLASS_DDC;
-+ adap->algo = &bcm2708_i2c_algorithm;
-+ adap->algo_data = bi;
-+ adap->dev.parent = &pdev->dev;
-+ adap->nr = pdev->id;
-+ strlcpy(adap->name, dev_name(&pdev->dev), sizeof(adap->name));
-+ adap->dev.of_node = pdev->dev.of_node;
-+
-+ switch (pdev->id) {
-+ case 0:
-+ adap->class = I2C_CLASS_HWMON;
-+ break;
-+ case 1:
-+ adap->class = I2C_CLASS_DDC;
-+ break;
-+ case 2:
-+ adap->class = I2C_CLASS_DDC;
-+ break;
-+ default:
-+ dev_err(&pdev->dev, "can only bind to BSC 0, 1 or 2\n");
-+ err = -ENXIO;
-+ goto out_free_bi;
-+ }
-+
-+ spin_lock_init(&bi->lock);
-+ init_completion(&bi->done);
-+
-+ bi->base = ioremap(regs->start, resource_size(regs));
-+ if (!bi->base) {
-+ dev_err(&pdev->dev, "could not remap memory\n");
-+ goto out_free_bi;
-+ }
-+
-+ bi->irq = irq;
-+ bi->clk = clk;
-+
-+ err = request_irq(irq, bcm2708_i2c_interrupt, IRQF_SHARED,
-+ dev_name(&pdev->dev), bi);
-+ if (err) {
-+ dev_err(&pdev->dev, "could not request IRQ: %d\n", err);
-+ goto out_iounmap;
-+ }
-+
-+ bcm2708_bsc_reset(bi);
-+
-+ err = i2c_add_numbered_adapter(adap);
-+ if (err < 0) {
-+ dev_err(&pdev->dev, "could not add I2C adapter: %d\n", err);
-+ goto out_free_irq;
-+ }
-+
-+ bus_hz = clk_get_rate(bi->clk);
-+ cdiv = bus_hz / baudrate;
-+ if (cdiv > 0xffff) {
-+ cdiv = 0xffff;
-+ baudrate = bus_hz / cdiv;
-+ }
-+ bi->cdiv = cdiv;
-+
-+ dev_info(&pdev->dev, "BSC%d Controller at 0x%08lx (irq %d) (baudrate %d)\n",
-+ pdev->id, (unsigned long)regs->start, irq, baudrate);
-+
-+ return 0;
-+
-+out_free_irq:
-+ free_irq(bi->irq, bi);
-+out_iounmap:
-+ iounmap(bi->base);
-+out_free_bi:
-+ kfree(bi);
-+out_clk_disable:
-+ clk_disable_unprepare(clk);
-+out_clk_put:
-+ clk_put(clk);
-+ return err;
-+}
-+
-+static int bcm2708_i2c_remove(struct platform_device *pdev)
-+{
-+ struct bcm2708_i2c *bi = platform_get_drvdata(pdev);
-+
-+ platform_set_drvdata(pdev, NULL);
-+
-+ i2c_del_adapter(&bi->adapter);
-+ free_irq(bi->irq, bi);
-+ iounmap(bi->base);
-+ clk_disable_unprepare(bi->clk);
-+ clk_put(bi->clk);
-+ kfree(bi);
-+
-+ return 0;
-+}
-+
-+static const struct of_device_id bcm2708_i2c_of_match[] = {
-+ { .compatible = "brcm,bcm2708-i2c" },
-+ {},
-+};
-+MODULE_DEVICE_TABLE(of, bcm2708_i2c_of_match);
-+
-+static struct platform_driver bcm2708_i2c_driver = {
-+ .driver = {
-+ .name = DRV_NAME,
-+ .owner = THIS_MODULE,
-+ .of_match_table = bcm2708_i2c_of_match,
-+ },
-+ .probe = bcm2708_i2c_probe,
-+ .remove = bcm2708_i2c_remove,
-+};
-+
-+// module_platform_driver(bcm2708_i2c_driver);
-+
-+
-+static int __init bcm2708_i2c_init(void)
-+{
-+ return platform_driver_register(&bcm2708_i2c_driver);
-+}
-+
-+static void __exit bcm2708_i2c_exit(void)
-+{
-+ platform_driver_unregister(&bcm2708_i2c_driver);
-+}
-+
-+module_init(bcm2708_i2c_init);
-+module_exit(bcm2708_i2c_exit);
-+
-+
-+
-+MODULE_DESCRIPTION("BSC controller driver for Broadcom BCM2708");
-+MODULE_AUTHOR("Chris Boot <bootc at bootc.net>");
-+MODULE_LICENSE("GPL v2");
-+MODULE_ALIAS("platform:" DRV_NAME);
diff --git a/target/linux/brcm2708/patches-4.4/0046-char-broadcom-Add-vcio-module.patch b/target/linux/brcm2708/patches-4.4/0046-char-broadcom-Add-vcio-module.patch
deleted file mode 100644
index da9c0f5..0000000
--- a/target/linux/brcm2708/patches-4.4/0046-char-broadcom-Add-vcio-module.patch
+++ /dev/null
@@ -1,221 +0,0 @@
-From df09439826fa8830d9a5c0ec21460284b72b02ce Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Noralf=20Tr=C3=B8nnes?= <noralf at tronnes.org>
-Date: Fri, 26 Jun 2015 14:27:06 +0200
-Subject: [PATCH] char: broadcom: Add vcio module
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Add module for accessing the mailbox property channel through
-/dev/vcio. Was previously in bcm2708-vcio.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
----
- drivers/char/broadcom/Kconfig | 6 ++
- drivers/char/broadcom/Makefile | 1 +
- drivers/char/broadcom/vcio.c | 175 +++++++++++++++++++++++++++++++++++++++++
- 3 files changed, 182 insertions(+)
- create mode 100644 drivers/char/broadcom/vcio.c
-
---- a/drivers/char/broadcom/Kconfig
-+++ b/drivers/char/broadcom/Kconfig
-@@ -22,6 +22,12 @@ config BCM2708_VCMEM
- help
- Helper for videocore memory access and total size allocation.
-
-+config BCM_VCIO
-+ tristate "Mailbox userspace access"
-+ depends on BCM2835_MBOX
-+ help
-+ Gives access to the mailbox property channel from userspace.
-+
- endif
-
- config BCM_VC_SM
---- a/drivers/char/broadcom/Makefile
-+++ b/drivers/char/broadcom/Makefile
-@@ -1,5 +1,6 @@
- obj-$(CONFIG_BCM_VC_CMA) += vc_cma/
- obj-$(CONFIG_BCM2708_VCMEM) += vc_mem.o
-+obj-$(CONFIG_BCM_VCIO) += vcio.o
- obj-$(CONFIG_BCM_VC_SM) += vc_sm/
-
- obj-$(CONFIG_BCM2835_DEVGPIOMEM)+= bcm2835-gpiomem.o
---- /dev/null
-+++ b/drivers/char/broadcom/vcio.c
-@@ -0,0 +1,175 @@
-+/*
-+ * Copyright (C) 2010 Broadcom
-+ * Copyright (C) 2015 Noralf Trønnes
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ *
-+ */
-+
-+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
-+
-+#include <linux/cdev.h>
-+#include <linux/device.h>
-+#include <linux/fs.h>
-+#include <linux/init.h>
-+#include <linux/ioctl.h>
-+#include <linux/module.h>
-+#include <linux/slab.h>
-+#include <linux/uaccess.h>
-+#include <soc/bcm2835/raspberrypi-firmware.h>
-+
-+#define MBOX_CHAN_PROPERTY 8
-+
-+#define VCIO_IOC_MAGIC 100
-+#define IOCTL_MBOX_PROPERTY _IOWR(VCIO_IOC_MAGIC, 0, char *)
-+
-+static struct {
-+ dev_t devt;
-+ struct cdev cdev;
-+ struct class *class;
-+ struct rpi_firmware *fw;
-+} vcio;
-+
-+static int vcio_user_property_list(void *user)
-+{
-+ u32 *buf, size;
-+ int ret;
-+
-+ /* The first 32-bit is the size of the buffer */
-+ if (copy_from_user(&size, user, sizeof(size)))
-+ return -EFAULT;
-+
-+ buf = kmalloc(size, GFP_KERNEL);
-+ if (!buf)
-+ return -ENOMEM;
-+
-+ if (copy_from_user(buf, user, size)) {
-+ kfree(buf);
-+ return -EFAULT;
-+ }
-+
-+ /* Strip off protocol encapsulation */
-+ ret = rpi_firmware_property_list(vcio.fw, &buf[2], size - 12);
-+ if (ret) {
-+ kfree(buf);
-+ return ret;
-+ }
-+
-+ buf[1] = RPI_FIRMWARE_STATUS_SUCCESS;
-+ if (copy_to_user(user, buf, size))
-+ ret = -EFAULT;
-+
-+ kfree(buf);
-+
-+ return ret;
-+}
-+
-+static int vcio_device_open(struct inode *inode, struct file *file)
-+{
-+ try_module_get(THIS_MODULE);
-+
-+ return 0;
-+}
-+
-+static int vcio_device_release(struct inode *inode, struct file *file)
-+{
-+ module_put(THIS_MODULE);
-+
-+ return 0;
-+}
-+
-+static long vcio_device_ioctl(struct file *file, unsigned int ioctl_num,
-+ unsigned long ioctl_param)
-+{
-+ switch (ioctl_num) {
-+ case IOCTL_MBOX_PROPERTY:
-+ return vcio_user_property_list((void *)ioctl_param);
-+ default:
-+ pr_err("unknown ioctl: %d\n", ioctl_num);
-+ return -EINVAL;
-+ }
-+}
-+
-+const struct file_operations vcio_fops = {
-+ .unlocked_ioctl = vcio_device_ioctl,
-+ .open = vcio_device_open,
-+ .release = vcio_device_release,
-+};
-+
-+static int __init vcio_init(void)
-+{
-+ struct device_node *np;
-+ static struct device *dev;
-+ int ret;
-+
-+ np = of_find_compatible_node(NULL, NULL,
-+ "raspberrypi,bcm2835-firmware");
-+/* Uncomment this when we only boot with Device Tree
-+ if (!of_device_is_available(np))
-+ return -ENODEV;
-+*/
-+ vcio.fw = rpi_firmware_get(np);
-+ if (!vcio.fw)
-+ return -ENODEV;
-+
-+ ret = alloc_chrdev_region(&vcio.devt, 0, 1, "vcio");
-+ if (ret) {
-+ pr_err("failed to allocate device number\n");
-+ return ret;
-+ }
-+
-+ cdev_init(&vcio.cdev, &vcio_fops);
-+ vcio.cdev.owner = THIS_MODULE;
-+ ret = cdev_add(&vcio.cdev, vcio.devt, 1);
-+ if (ret) {
-+ pr_err("failed to register device\n");
-+ goto err_unregister_chardev;
-+ }
-+
-+ /*
-+ * Create sysfs entries
-+ * 'bcm2708_vcio' is used for backwards compatibility so we don't break
-+ * userspace. Raspian has a udev rule that changes the permissions.
-+ */
-+ vcio.class = class_create(THIS_MODULE, "bcm2708_vcio");
-+ if (IS_ERR(vcio.class)) {
-+ ret = PTR_ERR(vcio.class);
-+ pr_err("failed to create class\n");
-+ goto err_cdev_del;
-+ }
-+
-+ dev = device_create(vcio.class, NULL, vcio.devt, NULL, "vcio");
-+ if (IS_ERR(dev)) {
-+ ret = PTR_ERR(dev);
-+ pr_err("failed to create device\n");
-+ goto err_class_destroy;
-+ }
-+
-+ return 0;
-+
-+err_class_destroy:
-+ class_destroy(vcio.class);
-+err_cdev_del:
-+ cdev_del(&vcio.cdev);
-+err_unregister_chardev:
-+ unregister_chrdev_region(vcio.devt, 1);
-+
-+ return ret;
-+}
-+module_init(vcio_init);
-+
-+static void __exit vcio_exit(void)
-+{
-+ device_destroy(vcio.class, vcio.devt);
-+ class_destroy(vcio.class);
-+ cdev_del(&vcio.cdev);
-+ unregister_chrdev_region(vcio.devt, 1);
-+}
-+module_exit(vcio_exit);
-+
-+MODULE_AUTHOR("Gray Girling");
-+MODULE_AUTHOR("Noralf Trønnes");
-+MODULE_DESCRIPTION("Mailbox userspace access");
-+MODULE_LICENSE("GPL");
diff --git a/target/linux/brcm2708/patches-4.4/0047-firmware-bcm2835-Support-ARCH_BCM270x.patch b/target/linux/brcm2708/patches-4.4/0047-firmware-bcm2835-Support-ARCH_BCM270x.patch
deleted file mode 100644
index 3d2a4e6..0000000
--- a/target/linux/brcm2708/patches-4.4/0047-firmware-bcm2835-Support-ARCH_BCM270x.patch
+++ /dev/null
@@ -1,106 +0,0 @@
-From e1a2f737f401288dd86e8adef4cc492ba4c4f0d5 Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Noralf=20Tr=C3=B8nnes?= <noralf at tronnes.org>
-Date: Fri, 26 Jun 2015 14:25:01 +0200
-Subject: [PATCH] firmware: bcm2835: Support ARCH_BCM270x
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Support booting without Device Tree.
-Turn on USB power.
-Load driver early because of lacking support for deferred probing
-in many drivers.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
----
- drivers/firmware/raspberrypi.c | 41 +++++++++++++++++++++++++++++++++++++++--
- 1 file changed, 39 insertions(+), 2 deletions(-)
-
---- a/drivers/firmware/raspberrypi.c
-+++ b/drivers/firmware/raspberrypi.c
-@@ -28,6 +28,8 @@ struct rpi_firmware {
- u32 enabled;
- };
-
-+static struct platform_device *g_pdev;
-+
- static DEFINE_MUTEX(transaction_lock);
-
- static void response_callback(struct mbox_client *cl, void *msg)
-@@ -183,6 +185,25 @@ rpi_firmware_print_firmware_revision(str
- }
- }
-
-+static int raspberrypi_firmware_set_power(struct rpi_firmware *fw,
-+ u32 domain, bool on)
-+{
-+ struct {
-+ u32 domain;
-+ u32 on;
-+ } packet;
-+ int ret;
-+
-+ packet.domain = domain;
-+ packet.on = on;
-+ ret = rpi_firmware_property(fw, RPI_FIRMWARE_SET_POWER_STATE,
-+ &packet, sizeof(packet));
-+ if (!ret && packet.on != on)
-+ ret = -EINVAL;
-+
-+ return ret;
-+}
-+
- static int rpi_firmware_probe(struct platform_device *pdev)
- {
- struct device *dev = &pdev->dev;
-@@ -207,9 +228,13 @@ static int rpi_firmware_probe(struct pla
- init_completion(&fw->c);
-
- platform_set_drvdata(pdev, fw);
-+ g_pdev = pdev;
-
- rpi_firmware_print_firmware_revision(fw);
-
-+ if (raspberrypi_firmware_set_power(fw, 3, true))
-+ dev_err(dev, "failed to turn on USB power\n");
-+
- return 0;
- }
-
-@@ -218,6 +243,7 @@ static int rpi_firmware_remove(struct pl
- struct rpi_firmware *fw = platform_get_drvdata(pdev);
-
- mbox_free_channel(fw->chan);
-+ g_pdev = NULL;
-
- return 0;
- }
-@@ -230,7 +256,7 @@ static int rpi_firmware_remove(struct pl
- */
- struct rpi_firmware *rpi_firmware_get(struct device_node *firmware_node)
- {
-- struct platform_device *pdev = of_find_device_by_node(firmware_node);
-+ struct platform_device *pdev = g_pdev;
-
- if (!pdev)
- return NULL;
-@@ -253,7 +279,18 @@ static struct platform_driver rpi_firmwa
- .probe = rpi_firmware_probe,
- .remove = rpi_firmware_remove,
- };
--module_platform_driver(rpi_firmware_driver);
-+
-+static int __init rpi_firmware_init(void)
-+{
-+ return platform_driver_register(&rpi_firmware_driver);
-+}
-+subsys_initcall(rpi_firmware_init);
-+
-+static void __init rpi_firmware_exit(void)
-+{
-+ platform_driver_unregister(&rpi_firmware_driver);
-+}
-+module_exit(rpi_firmware_exit);
-
- MODULE_AUTHOR("Eric Anholt <eric at anholt.net>");
- MODULE_DESCRIPTION("Raspberry Pi firmware driver");
diff --git a/target/linux/brcm2708/patches-4.4/0048-bcm2835-add-v4l2-camera-device.patch b/target/linux/brcm2708/patches-4.4/0048-bcm2835-add-v4l2-camera-device.patch
deleted file mode 100644
index 6be5d19..0000000
--- a/target/linux/brcm2708/patches-4.4/0048-bcm2835-add-v4l2-camera-device.patch
+++ /dev/null
@@ -1,7338 +0,0 @@
-From f953e64bd8b400ed2ddf67f256d560835245c7ae Mon Sep 17 00:00:00 2001
-From: Vincent Sanders <vincent.sanders at collabora.co.uk>
-Date: Wed, 30 Jan 2013 12:45:18 +0000
-Subject: [PATCH] bcm2835: add v4l2 camera device
-
-- Supports raw YUV capture, preview, JPEG and H264.
-- Uses videobuf2 for data transfer, using dma_buf.
-- Uses 3.6.10 timestamping
-- Camera power based on use
-- Uses immutable input mode on video encoder
-
-Signed-off-by: Daniel Stone <daniels at collabora.com>
-Signed-off-by: Luke Diamand <luked at broadcom.com>
-
-V4L2: Fixes from 6by9
-
-V4L2: Fix EV values. Add manual shutter speed control
-
-V4L2 EV values should be in units of 1/1000. Corrected.
-Add support for V4L2_CID_EXPOSURE_ABSOLUTE which should
-give manual shutter control. Requires manual exposure mode
-to be selected first.
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Correct JPEG Q-factor range
-
-Should be 1-100, not 0-100
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Fix issue of driver jamming if STREAMON failed.
-
-Fix issue where the driver was left in a partially enabled
-state if STREAMON failed, and would then reject many IOCTLs
-as it thought it was streaming.
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Fix ISO controls.
-
-Driver was passing the index to the GPU, and not the desired
-ISO value.
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Add flicker avoidance controls
-
-Add support for V4L2_CID_POWER_LINE_FREQUENCY to set flicker
-avoidance frequencies.
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Add support for frame rate control.
-
-Add support for frame rate (or time per frame as V4L2
-inverts it) control via s_parm.
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Improve G_FBUF handling so we pass conformance
-
-Return some sane numbers for get framebuffer so that
-we pass conformance.
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Fix information advertised through g_vidfmt
-
-Width and height were being stored based on incorrect
-values.
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Add support for inline H264 headers
-
-Add support for V4L2_CID_MPEG_VIDEO_REPEAT_SEQ_HEADER
-to control H264 inline headers.
-Requires firmware fix to work correctly, otherwise format
-has to be set to H264 before this parameter is set.
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Fix JPEG timestamp issue
-
-JPEG images were coming through from the GPU with timestamp
-of 0. Detect this and give current system time instead
-of some invalid value.
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Fix issue when switching down JPEG resolution.
-
-JPEG buffer size calculation is based on input resolution.
-Input resolution was being configured after output port
-format. Caused failures if switching from one JPEG resolution
-to a smaller one.
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Enable MJPEG encoding
-
-Requires GPU firmware update to support MJPEG encoder.
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Correct flag settings for compressed formats
-
-Set flags field correctly on enum_fmt_vid_cap for compressed
-image formats.
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: H264 profile & level ctrls, FPS control and auto exp pri
-
-Several control handling updates.
-H264 profile and level controls.
-Timeperframe/FPS reworked to add V4L2_CID_EXPOSURE_AUTO_PRIORITY to
-select whether AE is allowed to override the framerate specified.
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Correct BGR24 to RGB24 in format table
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Add additional pixel formats. Correct colourspace
-
-Adds the other flavours of YUYV, and NV12.
-Corrects the overlay advertised colourspace.
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Drop logging msg from info to debug
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Initial pass at scene modes.
-
-Only supports exposure mode and metering modes.
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Add manual white balance control.
-
-Adds support for V4L2_CID_RED_BALANCE and
-V4L2_CID_BLUE_BALANCE. Only has an effect if
-V4L2_CID_AUTO_N_PRESET_WHITE_BALANCE has
-V4L2_WHITE_BALANCE_MANUAL selected.
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-config: Enable V4L / MMAL driver
-
-V4L2: Increase the MMAL timeout to 3sec
-
-MJPEG codec flush is now taking longer and results
-in a kernel panic if the driver has stopped waiting for
-the result when it finally completes.
-Increase the timeout value from 1 to 3secs.
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Add support for setting H264_I_PERIOD
-
-Adds support for the parameter V4L2_CID_MPEG_VIDEO_H264_I_PERIOD
-to set the frequency with which I frames are produced.
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Enable GPU function for removing padding from images.
-
-GPU can now support arbitrary strides, although may require
-additional processing to achieve it. Enable this feature
-so that the images delivered are the size requested.
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Add support for V4L2_PIX_FMT_BGR32
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Set the colourspace to avoid odd YUV-RGB conversions
-
-Removes the amiguity from the conversion routines and stops
-them dropping back to the SD vs HD choice of coeffs.
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Make video/still threshold a run-time param
-
-Move the define for at what resolution the driver
-switches from a video mode capture to a stills mode
-capture to module parameters.
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Fix incorrect pool sizing
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Add option to disable enum_framesizes.
-
-Gstreamer's handling of a driver that advertises
-V4L2_FRMSIZE_TYPE_STEPWISE to define the supported
-resolutions is broken. See bug
-https://bugzilla.gnome.org/show_bug.cgi?id=726521
-
-Optional parameter of gst_v4l2src_is_broken added.
-If non-zero, the driver claims not to support that
-ioctl, and gstreamer should be happy again (it
-guesses a set of defaults for itself).
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Add support for more image formats
-
-Adds YVU420 (YV12), YVU420SP (NV21), and BGR888.
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-V4L2: Extend range for V4L2_CID_MPEG_VIDEO_H264_I_PERIOD
-
-Request to extend the range from the fairly arbitrary
-1000 frames (33 seconds at 30fps). Extend out to the
-max range supported (int32 value).
-Also allow 0, which is handled by the codec as only
-send an I-frame on the first frame and never again.
-There may be an exception if it detects a significant
-scene change, but there's no easy way around that.
-
-Signed-off-by: Dave Stevenson <dsteve at broadcom.com>
-
-bcm2835-camera: stop_streaming now has a void return
-
-BCM2835-V4L2: Fix compliance test failures
-
-VIDIOC_TRY_FMT and VIDIOC_S_FMT tests were faling due
-to reporting V4L2_COLORSPACE_JPEG when the colour
-format wasn't V4L2_PIX_FMT_JPEG.
-Now reports V4L2_COLORSPACE_SMPTE170M for YUV formats.
-
-bcm2835 camera planar/packed stride length
-
-Added a field to the mmal_fmt struct used to compute the bytes per line
-when using a particular format. This results in the correct stride being
-calculated even when the format is planar.
-
-Signed-off-by: Garrett Wilson <g at floft.net>
-
-bcm2835: camera: check for scene not being found
-
-static analysis by cppcheck detected some potential NULL pointer
-dereference issues:
-
-[drivers/media/platform/bcm2835/controls.c:854]: (error) Possible null
- pointer dereference: scene
- (and lines 858, 859 too)
-
-it is possible that scene is not found because of an invalue ctrl->val
-and is therefore NULL and hence causing a null pointer dereference.
-
-Signed-off-by: Colin Ian King <colin.king at canonical.com>
-
-bcm2835: memcpy port data to m rather than rmsg
-
-static analysis by cppcheck detected a memcpy to rmsg which is
-not actually initialized at that point. The memcpy should be copying
-to variable m instead.
-
-Signed-off-by: Colin Ian King <colin.king at canonical.com>
-
-BCM2835-V4L2: Return buffers to videobuf2 on shutdown
-
-https://github.com/raspberrypi/linux/issues/817
-Fixes the kernel warning from videobuf2 as buffers
-are now returned as they are being flushed on
-stop_streaming.
-
-squash: Fixup bcm2835-camera for changes in kernel 4.4 api
----
- Documentation/video4linux/bcm2835-v4l2.txt | 60 +
- drivers/media/platform/Kconfig | 2 +
- drivers/media/platform/Makefile | 2 +
- drivers/media/platform/bcm2835/Kconfig | 25 +
- drivers/media/platform/bcm2835/Makefile | 5 +
- drivers/media/platform/bcm2835/bcm2835-camera.c | 1844 +++++++++++++++++++++
- drivers/media/platform/bcm2835/bcm2835-camera.h | 126 ++
- drivers/media/platform/bcm2835/controls.c | 1324 +++++++++++++++
- drivers/media/platform/bcm2835/mmal-common.h | 53 +
- drivers/media/platform/bcm2835/mmal-encodings.h | 127 ++
- drivers/media/platform/bcm2835/mmal-msg-common.h | 50 +
- drivers/media/platform/bcm2835/mmal-msg-format.h | 81 +
- drivers/media/platform/bcm2835/mmal-msg-port.h | 107 ++
- drivers/media/platform/bcm2835/mmal-msg.h | 404 +++++
- drivers/media/platform/bcm2835/mmal-parameters.h | 656 ++++++++
- drivers/media/platform/bcm2835/mmal-vchiq.c | 1916 ++++++++++++++++++++++
- drivers/media/platform/bcm2835/mmal-vchiq.h | 178 ++
- 17 files changed, 6960 insertions(+)
- create mode 100644 Documentation/video4linux/bcm2835-v4l2.txt
- create mode 100644 drivers/media/platform/bcm2835/Kconfig
- create mode 100644 drivers/media/platform/bcm2835/Makefile
- create mode 100644 drivers/media/platform/bcm2835/bcm2835-camera.c
- create mode 100644 drivers/media/platform/bcm2835/bcm2835-camera.h
- create mode 100644 drivers/media/platform/bcm2835/controls.c
- create mode 100644 drivers/media/platform/bcm2835/mmal-common.h
- create mode 100644 drivers/media/platform/bcm2835/mmal-encodings.h
- create mode 100644 drivers/media/platform/bcm2835/mmal-msg-common.h
- create mode 100644 drivers/media/platform/bcm2835/mmal-msg-format.h
- create mode 100644 drivers/media/platform/bcm2835/mmal-msg-port.h
- create mode 100644 drivers/media/platform/bcm2835/mmal-msg.h
- create mode 100644 drivers/media/platform/bcm2835/mmal-parameters.h
- create mode 100644 drivers/media/platform/bcm2835/mmal-vchiq.c
- create mode 100644 drivers/media/platform/bcm2835/mmal-vchiq.h
-
---- /dev/null
-+++ b/Documentation/video4linux/bcm2835-v4l2.txt
-@@ -0,0 +1,60 @@
-+
-+BCM2835 (aka Raspberry Pi) V4L2 driver
-+======================================
-+
-+1. Copyright
-+============
-+
-+Copyright © 2013 Raspberry Pi (Trading) Ltd.
-+
-+2. License
-+==========
-+
-+This program is free software; you can redistribute it and/or modify
-+it under the terms of the GNU General Public License as published by
-+the Free Software Foundation; either version 2 of the License, or
-+(at your option) any later version.
-+
-+This program is distributed in the hope that it will be useful,
-+but WITHOUT ANY WARRANTY; without even the implied warranty of
-+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+GNU General Public License for more details.
-+
-+You should have received a copy of the GNU General Public License
-+along with this program; if not, write to the Free Software
-+Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
-+
-+3. Quick Start
-+==============
-+
-+You need a version 1.0 or later of v4l2-ctl, available from:
-+ git://git.linuxtv.org/v4l-utils.git
-+
-+$ sudo modprobe bcm2835-v4l2
-+
-+Turn on the overlay:
-+
-+$ v4l2-ctl --overlay=1
-+
-+Turn off the overlay:
-+
-+$ v4l2-ctl --overlay=0
-+
-+Set the capture format for video:
-+
-+$ v4l2-ctl --set-fmt-video=width=1920,height=1088,pixelformat=4
-+
-+(Note: 1088 not 1080).
-+
-+Capture:
-+
-+$ v4l2-ctl --stream-mmap=3 --stream-count=100 --stream-to=somefile.h264
-+
-+Stills capture:
-+
-+$ v4l2-ctl --set-fmt-video=width=2592,height=1944,pixelformat=3
-+$ v4l2-ctl --stream-mmap=3 --stream-count=1 --stream-to=somefile.jpg
-+
-+List of available formats:
-+
-+$ v4l2-ctl --list-formats
---- a/drivers/media/platform/Kconfig
-+++ b/drivers/media/platform/Kconfig
-@@ -11,6 +11,8 @@ menuconfig V4L_PLATFORM_DRIVERS
-
- if V4L_PLATFORM_DRIVERS
-
-+source "drivers/media/platform/bcm2835/Kconfig"
-+
- source "drivers/media/platform/marvell-ccic/Kconfig"
-
- config VIDEO_VIA_CAMERA
---- a/drivers/media/platform/Makefile
-+++ b/drivers/media/platform/Makefile
-@@ -2,6 +2,8 @@
- # Makefile for the video capture/playback device drivers.
- #
-
-+obj-$(CONFIG_VIDEO_BCM2835) += bcm2835/
-+
- obj-$(CONFIG_VIDEO_TIMBERDALE) += timblogiw.o
- obj-$(CONFIG_VIDEO_M32R_AR_M64278) += arv.o
-
---- /dev/null
-+++ b/drivers/media/platform/bcm2835/Kconfig
-@@ -0,0 +1,25 @@
-+# Broadcom VideoCore IV v4l2 camera support
-+
-+config VIDEO_BCM2835
-+ bool "Broadcom BCM2835 camera interface driver"
-+ depends on VIDEO_V4L2 && (ARCH_BCM2708 || ARCH_BCM2709 || ARCH_BCM2835)
-+ ---help---
-+ Say Y here to enable camera host interface devices for
-+ Broadcom BCM2835 SoC. This operates over the VCHIQ interface
-+ to a service running on VideoCore.
-+
-+
-+if VIDEO_BCM2835
-+
-+config VIDEO_BCM2835_MMAL
-+ tristate "Broadcom BM2835 MMAL camera interface driver"
-+ depends on BCM2708_VCHIQ
-+ select VIDEOBUF2_VMALLOC
-+ ---help---
-+ This is a V4L2 driver for the Broadcom BCM2835 MMAL camera host interface
-+
-+ To compile this driver as a module, choose M here: the
-+ module will be called bcm2835-v4l2.o
-+
-+
-+endif # VIDEO_BM2835
---- /dev/null
-+++ b/drivers/media/platform/bcm2835/Makefile
-@@ -0,0 +1,5 @@
-+bcm2835-v4l2-objs := bcm2835-camera.o controls.o mmal-vchiq.o
-+
-+obj-$(CONFIG_VIDEO_BCM2835_MMAL) += bcm2835-v4l2.o
-+
-+ccflags-$(CONFIG_VIDEO_BCM2835) += -Idrivers/misc/vc04_services -Idrivers/misc/vc04_services/interface/vcos/linuxkernel -D__VCCOREVER__=0x04000000
---- /dev/null
-+++ b/drivers/media/platform/bcm2835/bcm2835-camera.c
-@@ -0,0 +1,1844 @@
-+/*
-+ * Broadcom BM2835 V4L2 driver
-+ *
-+ * Copyright © 2013 Raspberry Pi (Trading) Ltd.
-+ *
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License. See the file COPYING in the main directory of this archive
-+ * for more details.
-+ *
-+ * Authors: Vincent Sanders <vincent.sanders at collabora.co.uk>
-+ * Dave Stevenson <dsteve at broadcom.com>
-+ * Simon Mellor <simellor at broadcom.com>
-+ * Luke Diamand <luked at broadcom.com>
-+ */
-+
-+#include <linux/errno.h>
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+#include <linux/slab.h>
-+#include <media/videobuf2-vmalloc.h>
-+#include <media/videobuf2-dma-contig.h>
-+#include <media/v4l2-device.h>
-+#include <media/v4l2-ioctl.h>
-+#include <media/v4l2-ctrls.h>
-+#include <media/v4l2-fh.h>
-+#include <media/v4l2-event.h>
-+#include <media/v4l2-common.h>
-+#include <linux/delay.h>
-+
-+#include "mmal-common.h"
-+#include "mmal-encodings.h"
-+#include "mmal-vchiq.h"
-+#include "mmal-msg.h"
-+#include "mmal-parameters.h"
-+#include "bcm2835-camera.h"
-+
-+#define BM2835_MMAL_VERSION "0.0.2"
-+#define BM2835_MMAL_MODULE_NAME "bcm2835-v4l2"
-+#define MIN_WIDTH 16
-+#define MIN_HEIGHT 16
-+#define MAX_WIDTH 2592
-+#define MAX_HEIGHT 1944
-+#define MIN_BUFFER_SIZE (80*1024)
-+
-+#define MAX_VIDEO_MODE_WIDTH 1280
-+#define MAX_VIDEO_MODE_HEIGHT 720
-+
-+MODULE_DESCRIPTION("Broadcom 2835 MMAL video capture");
-+MODULE_AUTHOR("Vincent Sanders");
-+MODULE_LICENSE("GPL");
-+MODULE_VERSION(BM2835_MMAL_VERSION);
-+
-+int bcm2835_v4l2_debug;
-+module_param_named(debug, bcm2835_v4l2_debug, int, 0644);
-+MODULE_PARM_DESC(bcm2835_v4l2_debug, "Debug level 0-2");
-+
-+int max_video_width = MAX_VIDEO_MODE_WIDTH;
-+int max_video_height = MAX_VIDEO_MODE_HEIGHT;
-+module_param(max_video_width, int, S_IRUSR | S_IWUSR | S_IRGRP | S_IROTH);
-+MODULE_PARM_DESC(max_video_width, "Threshold for video mode");
-+module_param(max_video_height, int, S_IRUSR | S_IWUSR | S_IRGRP | S_IROTH);
-+MODULE_PARM_DESC(max_video_height, "Threshold for video mode");
-+
-+/* Gstreamer bug https://bugzilla.gnome.org/show_bug.cgi?id=726521
-+ * v4l2src does bad (and actually wrong) things when the vidioc_enum_framesizes
-+ * function says type V4L2_FRMSIZE_TYPE_STEPWISE, which we do by default.
-+ * It's happier if we just don't say anything at all, when it then
-+ * sets up a load of defaults that it thinks might work.
-+ * If gst_v4l2src_is_broken is non-zero, then we remove the function from
-+ * our function table list (actually switch to an alternate set, but same
-+ * result).
-+ */
-+int gst_v4l2src_is_broken = 0;
-+module_param(gst_v4l2src_is_broken, int, S_IRUSR | S_IWUSR | S_IRGRP | S_IROTH);
-+MODULE_PARM_DESC(gst_v4l2src_is_broken, "If non-zero, enable workaround for Gstreamer");
-+
-+static struct bm2835_mmal_dev *gdev; /* global device data */
-+
-+#define FPS_MIN 1
-+#define FPS_MAX 90
-+
-+/* timeperframe: min/max and default */
-+static const struct v4l2_fract
-+ tpf_min = {.numerator = 1, .denominator = FPS_MAX},
-+ tpf_max = {.numerator = 1, .denominator = FPS_MIN},
-+ tpf_default = {.numerator = 1000, .denominator = 30000};
-+
-+/* video formats */
-+static struct mmal_fmt formats[] = {
-+ {
-+ .name = "4:2:0, planar, YUV",
-+ .fourcc = V4L2_PIX_FMT_YUV420,
-+ .flags = 0,
-+ .mmal = MMAL_ENCODING_I420,
-+ .depth = 12,
-+ .mmal_component = MMAL_COMPONENT_CAMERA,
-+ .ybbp = 1,
-+ },
-+ {
-+ .name = "4:2:2, packed, YUYV",
-+ .fourcc = V4L2_PIX_FMT_YUYV,
-+ .flags = 0,
-+ .mmal = MMAL_ENCODING_YUYV,
-+ .depth = 16,
-+ .mmal_component = MMAL_COMPONENT_CAMERA,
-+ .ybbp = 2,
-+ },
-+ {
-+ .name = "RGB24 (LE)",
-+ .fourcc = V4L2_PIX_FMT_RGB24,
-+ .flags = 0,
-+ .mmal = MMAL_ENCODING_BGR24,
-+ .depth = 24,
-+ .mmal_component = MMAL_COMPONENT_CAMERA,
-+ .ybbp = 3,
-+ },
-+ {
-+ .name = "JPEG",
-+ .fourcc = V4L2_PIX_FMT_JPEG,
-+ .flags = V4L2_FMT_FLAG_COMPRESSED,
-+ .mmal = MMAL_ENCODING_JPEG,
-+ .depth = 8,
-+ .mmal_component = MMAL_COMPONENT_IMAGE_ENCODE,
-+ .ybbp = 0,
-+ },
-+ {
-+ .name = "H264",
-+ .fourcc = V4L2_PIX_FMT_H264,
-+ .flags = V4L2_FMT_FLAG_COMPRESSED,
-+ .mmal = MMAL_ENCODING_H264,
-+ .depth = 8,
-+ .mmal_component = MMAL_COMPONENT_VIDEO_ENCODE,
-+ .ybbp = 0,
-+ },
-+ {
-+ .name = "MJPEG",
-+ .fourcc = V4L2_PIX_FMT_MJPEG,
-+ .flags = V4L2_FMT_FLAG_COMPRESSED,
-+ .mmal = MMAL_ENCODING_MJPEG,
-+ .depth = 8,
-+ .mmal_component = MMAL_COMPONENT_VIDEO_ENCODE,
-+ .ybbp = 0,
-+ },
-+ {
-+ .name = "4:2:2, packed, YVYU",
-+ .fourcc = V4L2_PIX_FMT_YVYU,
-+ .flags = 0,
-+ .mmal = MMAL_ENCODING_YVYU,
-+ .depth = 16,
-+ .mmal_component = MMAL_COMPONENT_CAMERA,
-+ .ybbp = 2,
-+ },
-+ {
-+ .name = "4:2:2, packed, VYUY",
-+ .fourcc = V4L2_PIX_FMT_VYUY,
-+ .flags = 0,
-+ .mmal = MMAL_ENCODING_VYUY,
-+ .depth = 16,
-+ .mmal_component = MMAL_COMPONENT_CAMERA,
-+ .ybbp = 2,
-+ },
-+ {
-+ .name = "4:2:2, packed, UYVY",
-+ .fourcc = V4L2_PIX_FMT_UYVY,
-+ .flags = 0,
-+ .mmal = MMAL_ENCODING_UYVY,
-+ .depth = 16,
-+ .mmal_component = MMAL_COMPONENT_CAMERA,
-+ .ybbp = 2,
-+ },
-+ {
-+ .name = "4:2:0, planar, NV12",
-+ .fourcc = V4L2_PIX_FMT_NV12,
-+ .flags = 0,
-+ .mmal = MMAL_ENCODING_NV12,
-+ .depth = 12,
-+ .mmal_component = MMAL_COMPONENT_CAMERA,
-+ .ybbp = 1,
-+ },
-+ {
-+ .name = "RGB24 (BE)",
-+ .fourcc = V4L2_PIX_FMT_BGR24,
-+ .flags = 0,
-+ .mmal = MMAL_ENCODING_RGB24,
-+ .depth = 24,
-+ .mmal_component = MMAL_COMPONENT_CAMERA,
-+ .ybbp = 3,
-+ },
-+ {
-+ .name = "4:2:0, planar, YVU",
-+ .fourcc = V4L2_PIX_FMT_YVU420,
-+ .flags = 0,
-+ .mmal = MMAL_ENCODING_YV12,
-+ .depth = 12,
-+ .mmal_component = MMAL_COMPONENT_CAMERA,
-+ .ybbp = 1,
-+ },
-+ {
-+ .name = "4:2:0, planar, NV21",
-+ .fourcc = V4L2_PIX_FMT_NV21,
-+ .flags = 0,
-+ .mmal = MMAL_ENCODING_NV21,
-+ .depth = 12,
-+ .mmal_component = MMAL_COMPONENT_CAMERA,
-+ .ybbp = 1,
-+ },
-+ {
-+ .name = "RGB32 (BE)",
-+ .fourcc = V4L2_PIX_FMT_BGR32,
-+ .flags = 0,
-+ .mmal = MMAL_ENCODING_BGRA,
-+ .depth = 32,
-+ .mmal_component = MMAL_COMPONENT_CAMERA,
-+ .ybbp = 4,
-+ },
-+};
-+
-+static struct mmal_fmt *get_format(struct v4l2_format *f)
-+{
-+ struct mmal_fmt *fmt;
-+ unsigned int k;
-+
-+ for (k = 0; k < ARRAY_SIZE(formats); k++) {
-+ fmt = &formats[k];
-+ if (fmt->fourcc == f->fmt.pix.pixelformat)
-+ break;
-+ }
-+
-+ if (k == ARRAY_SIZE(formats))
-+ return NULL;
-+
-+ return &formats[k];
-+}
-+
-+/* ------------------------------------------------------------------
-+ Videobuf queue operations
-+ ------------------------------------------------------------------*/
-+
-+static int queue_setup(struct vb2_queue *vq, const void *parg,
-+ unsigned int *nbuffers, unsigned int *nplanes,
-+ unsigned int sizes[], void *alloc_ctxs[])
-+{
-+ struct bm2835_mmal_dev *dev = vb2_get_drv_priv(vq);
-+ unsigned long size;
-+
-+ /* refuse queue setup if port is not configured */
-+ if (dev->capture.port == NULL) {
-+ v4l2_err(&dev->v4l2_dev,
-+ "%s: capture port not configured\n", __func__);
-+ return -EINVAL;
-+ }
-+
-+ size = dev->capture.port->current_buffer.size;
-+ if (size == 0) {
-+ v4l2_err(&dev->v4l2_dev,
-+ "%s: capture port buffer size is zero\n", __func__);
-+ return -EINVAL;
-+ }
-+
-+ if (*nbuffers < (dev->capture.port->current_buffer.num + 2))
-+ *nbuffers = (dev->capture.port->current_buffer.num + 2);
-+
-+ *nplanes = 1;
-+
-+ sizes[0] = size;
-+
-+ /*
-+ * videobuf2-vmalloc allocator is context-less so no need to set
-+ * alloc_ctxs array.
-+ */
-+
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev, "%s: dev:%p\n",
-+ __func__, dev);
-+
-+ return 0;
-+}
-+
-+static int buffer_prepare(struct vb2_buffer *vb)
-+{
-+ struct bm2835_mmal_dev *dev = vb2_get_drv_priv(vb->vb2_queue);
-+ unsigned long size;
-+
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev, "%s: dev:%p\n",
-+ __func__, dev);
-+
-+ BUG_ON(dev->capture.port == NULL);
-+ BUG_ON(dev->capture.fmt == NULL);
-+
-+ size = dev->capture.stride * dev->capture.height;
-+ if (vb2_plane_size(vb, 0) < size) {
-+ v4l2_err(&dev->v4l2_dev,
-+ "%s data will not fit into plane (%lu < %lu)\n",
-+ __func__, vb2_plane_size(vb, 0), size);
-+ return -EINVAL;
-+ }
-+
-+ return 0;
-+}
-+
-+static inline bool is_capturing(struct bm2835_mmal_dev *dev)
-+{
-+ return dev->capture.camera_port ==
-+ &dev->
-+ component[MMAL_COMPONENT_CAMERA]->output[MMAL_CAMERA_PORT_CAPTURE];
-+}
-+
-+static void buffer_cb(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *port,
-+ int status,
-+ struct mmal_buffer *buf,
-+ unsigned long length, u32 mmal_flags, s64 dts, s64 pts)
-+{
-+ struct bm2835_mmal_dev *dev = port->cb_ctx;
-+
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "%s: status:%d, buf:%p, length:%lu, flags %u, pts %lld\n",
-+ __func__, status, buf, length, mmal_flags, pts);
-+
-+ if (status != 0) {
-+ /* error in transfer */
-+ if (buf != NULL) {
-+ /* there was a buffer with the error so return it */
-+ vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_ERROR);
-+ }
-+ return;
-+ } else if (length == 0) {
-+ /* stream ended */
-+ if (buf != NULL) {
-+ /* this should only ever happen if the port is
-+ * disabled and there are buffers still queued
-+ */
-+ vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_ERROR);
-+ pr_debug("Empty buffer");
-+ } else if (dev->capture.frame_count) {
-+ /* grab another frame */
-+ if (is_capturing(dev)) {
-+ pr_debug("Grab another frame");
-+ vchiq_mmal_port_parameter_set(
-+ instance,
-+ dev->capture.
-+ camera_port,
-+ MMAL_PARAMETER_CAPTURE,
-+ &dev->capture.
-+ frame_count,
-+ sizeof(dev->capture.frame_count));
-+ }
-+ } else {
-+ /* signal frame completion */
-+ complete(&dev->capture.frame_cmplt);
-+ }
-+ } else {
-+ if (dev->capture.frame_count) {
-+ if (dev->capture.vc_start_timestamp != -1 &&
-+ pts != 0) {
-+ s64 runtime_us = pts -
-+ dev->capture.vc_start_timestamp;
-+ u32 div = 0;
-+ u32 rem = 0;
-+
-+ div =
-+ div_u64_rem(runtime_us, USEC_PER_SEC, &rem);
-+ buf->vb.timestamp.tv_sec =
-+ dev->capture.kernel_start_ts.tv_sec - 1 +
-+ div;
-+ buf->vb.timestamp.tv_usec =
-+ dev->capture.kernel_start_ts.tv_usec + rem;
-+
-+ if (buf->vb.timestamp.tv_usec >=
-+ USEC_PER_SEC) {
-+ buf->vb.timestamp.tv_sec++;
-+ buf->vb.timestamp.tv_usec -=
-+ USEC_PER_SEC;
-+ }
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "Convert start time %d.%06d and %llu "
-+ "with offset %llu to %d.%06d\n",
-+ (int)dev->capture.kernel_start_ts.
-+ tv_sec,
-+ (int)dev->capture.kernel_start_ts.
-+ tv_usec,
-+ dev->capture.vc_start_timestamp, pts,
-+ (int)buf->vb.timestamp.tv_sec,
-+ (int)buf->vb.timestamp.
-+ tv_usec);
-+ } else {
-+ v4l2_get_timestamp(&buf->vb.timestamp);
-+ }
-+
-+ vb2_set_plane_payload(&buf->vb.vb2_buf, 0, length);
-+ vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_DONE);
-+
-+ if (mmal_flags & MMAL_BUFFER_HEADER_FLAG_EOS &&
-+ is_capturing(dev)) {
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "Grab another frame as buffer has EOS");
-+ vchiq_mmal_port_parameter_set(
-+ instance,
-+ dev->capture.
-+ camera_port,
-+ MMAL_PARAMETER_CAPTURE,
-+ &dev->capture.
-+ frame_count,
-+ sizeof(dev->capture.frame_count));
-+ }
-+ } else {
-+ /* signal frame completion */
-+ vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_ERROR);
-+ complete(&dev->capture.frame_cmplt);
-+ }
-+ }
-+}
-+
-+static int enable_camera(struct bm2835_mmal_dev *dev)
-+{
-+ int ret;
-+ if (!dev->camera_use_count) {
-+ ret = vchiq_mmal_component_enable(
-+ dev->instance,
-+ dev->component[MMAL_COMPONENT_CAMERA]);
-+ if (ret < 0) {
-+ v4l2_err(&dev->v4l2_dev,
-+ "Failed enabling camera, ret %d\n", ret);
-+ return -EINVAL;
-+ }
-+ }
-+ dev->camera_use_count++;
-+ v4l2_dbg(1, bcm2835_v4l2_debug,
-+ &dev->v4l2_dev, "enabled camera (refcount %d)\n",
-+ dev->camera_use_count);
-+ return 0;
-+}
-+
-+static int disable_camera(struct bm2835_mmal_dev *dev)
-+{
-+ int ret;
-+ if (!dev->camera_use_count) {
-+ v4l2_err(&dev->v4l2_dev,
-+ "Disabled the camera when already disabled\n");
-+ return -EINVAL;
-+ }
-+ dev->camera_use_count--;
-+ if (!dev->camera_use_count) {
-+ unsigned int i = 0xFFFFFFFF;
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "Disabling camera\n");
-+ ret =
-+ vchiq_mmal_component_disable(
-+ dev->instance,
-+ dev->component[MMAL_COMPONENT_CAMERA]);
-+ if (ret < 0) {
-+ v4l2_err(&dev->v4l2_dev,
-+ "Failed disabling camera, ret %d\n", ret);
-+ return -EINVAL;
-+ }
-+ vchiq_mmal_port_parameter_set(
-+ dev->instance,
-+ &dev->component[MMAL_COMPONENT_CAMERA]->control,
-+ MMAL_PARAMETER_CAMERA_NUM, &i,
-+ sizeof(i));
-+ }
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "Camera refcount now %d\n", dev->camera_use_count);
-+ return 0;
-+}
-+
-+static void buffer_queue(struct vb2_buffer *vb)
-+{
-+ struct bm2835_mmal_dev *dev = vb2_get_drv_priv(vb->vb2_queue);
-+ struct vb2_v4l2_buffer *vb2 = to_vb2_v4l2_buffer(vb);
-+ struct mmal_buffer *buf = container_of(vb2, struct mmal_buffer, vb);
-+ int ret;
-+
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "%s: dev:%p buf:%p\n", __func__, dev, buf);
-+
-+ buf->buffer = vb2_plane_vaddr(&buf->vb.vb2_buf, 0);
-+ buf->buffer_size = vb2_plane_size(&buf->vb.vb2_buf, 0);
-+
-+ ret = vchiq_mmal_submit_buffer(dev->instance, dev->capture.port, buf);
-+ if (ret < 0)
-+ v4l2_err(&dev->v4l2_dev, "%s: error submitting buffer\n",
-+ __func__);
-+}
-+
-+static int start_streaming(struct vb2_queue *vq, unsigned int count)
-+{
-+ struct bm2835_mmal_dev *dev = vb2_get_drv_priv(vq);
-+ int ret;
-+ int parameter_size;
-+
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev, "%s: dev:%p\n",
-+ __func__, dev);
-+
-+ /* ensure a format has actually been set */
-+ if (dev->capture.port == NULL)
-+ return -EINVAL;
-+
-+ if (enable_camera(dev) < 0) {
-+ v4l2_err(&dev->v4l2_dev, "Failed to enable camera\n");
-+ return -EINVAL;
-+ }
-+
-+ /*init_completion(&dev->capture.frame_cmplt); */
-+
-+ /* enable frame capture */
-+ dev->capture.frame_count = 1;
-+
-+ /* if the preview is not already running, wait for a few frames for AGC
-+ * to settle down.
-+ */
-+ if (!dev->component[MMAL_COMPONENT_PREVIEW]->enabled)
-+ msleep(300);
-+
-+ /* enable the connection from camera to encoder (if applicable) */
-+ if (dev->capture.camera_port != dev->capture.port
-+ && dev->capture.camera_port) {
-+ ret = vchiq_mmal_port_enable(dev->instance,
-+ dev->capture.camera_port, NULL);
-+ if (ret) {
-+ v4l2_err(&dev->v4l2_dev,
-+ "Failed to enable encode tunnel - error %d\n",
-+ ret);
-+ return -1;
-+ }
-+ }
-+
-+ /* Get VC timestamp at this point in time */
-+ parameter_size = sizeof(dev->capture.vc_start_timestamp);
-+ if (vchiq_mmal_port_parameter_get(dev->instance,
-+ dev->capture.camera_port,
-+ MMAL_PARAMETER_SYSTEM_TIME,
-+ &dev->capture.vc_start_timestamp,
-+ ¶meter_size)) {
-+ v4l2_err(&dev->v4l2_dev,
-+ "Failed to get VC start time - update your VC f/w\n");
-+
-+ /* Flag to indicate just to rely on kernel timestamps */
-+ dev->capture.vc_start_timestamp = -1;
-+ } else
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "Start time %lld size %d\n",
-+ dev->capture.vc_start_timestamp, parameter_size);
-+
-+ v4l2_get_timestamp(&dev->capture.kernel_start_ts);
-+
-+ /* enable the camera port */
-+ dev->capture.port->cb_ctx = dev;
-+ ret =
-+ vchiq_mmal_port_enable(dev->instance, dev->capture.port, buffer_cb);
-+ if (ret) {
-+ v4l2_err(&dev->v4l2_dev,
-+ "Failed to enable capture port - error %d. "
-+ "Disabling camera port again\n", ret);
-+
-+ vchiq_mmal_port_disable(dev->instance,
-+ dev->capture.camera_port);
-+ if (disable_camera(dev) < 0) {
-+ v4l2_err(&dev->v4l2_dev, "Failed to disable camera\n");
-+ return -EINVAL;
-+ }
-+ return -1;
-+ }
-+
-+ /* capture the first frame */
-+ vchiq_mmal_port_parameter_set(dev->instance,
-+ dev->capture.camera_port,
-+ MMAL_PARAMETER_CAPTURE,
-+ &dev->capture.frame_count,
-+ sizeof(dev->capture.frame_count));
-+ return 0;
-+}
-+
-+/* abort streaming and wait for last buffer */
-+static void stop_streaming(struct vb2_queue *vq)
-+{
-+ int ret;
-+ struct bm2835_mmal_dev *dev = vb2_get_drv_priv(vq);
-+
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev, "%s: dev:%p\n",
-+ __func__, dev);
-+
-+ init_completion(&dev->capture.frame_cmplt);
-+ dev->capture.frame_count = 0;
-+
-+ /* ensure a format has actually been set */
-+ if (dev->capture.port == NULL) {
-+ v4l2_err(&dev->v4l2_dev,
-+ "no capture port - stream not started?\n");
-+ return;
-+ }
-+
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev, "stopping capturing\n");
-+
-+ /* stop capturing frames */
-+ vchiq_mmal_port_parameter_set(dev->instance,
-+ dev->capture.camera_port,
-+ MMAL_PARAMETER_CAPTURE,
-+ &dev->capture.frame_count,
-+ sizeof(dev->capture.frame_count));
-+
-+ /* wait for last frame to complete */
-+ ret = wait_for_completion_timeout(&dev->capture.frame_cmplt, HZ);
-+ if (ret <= 0)
-+ v4l2_err(&dev->v4l2_dev,
-+ "error %d waiting for frame completion\n", ret);
-+
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "disabling connection\n");
-+
-+ /* disable the connection from camera to encoder */
-+ ret = vchiq_mmal_port_disable(dev->instance, dev->capture.camera_port);
-+ if (!ret && dev->capture.camera_port != dev->capture.port) {
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "disabling port\n");
-+ ret = vchiq_mmal_port_disable(dev->instance, dev->capture.port);
-+ } else if (dev->capture.camera_port != dev->capture.port) {
-+ v4l2_err(&dev->v4l2_dev, "port_disable failed, error %d\n",
-+ ret);
-+ }
-+
-+ if (disable_camera(dev) < 0)
-+ v4l2_err(&dev->v4l2_dev, "Failed to disable camera\n");
-+}
-+
-+static void bm2835_mmal_lock(struct vb2_queue *vq)
-+{
-+ struct bm2835_mmal_dev *dev = vb2_get_drv_priv(vq);
-+ mutex_lock(&dev->mutex);
-+}
-+
-+static void bm2835_mmal_unlock(struct vb2_queue *vq)
-+{
-+ struct bm2835_mmal_dev *dev = vb2_get_drv_priv(vq);
-+ mutex_unlock(&dev->mutex);
-+}
-+
-+static struct vb2_ops bm2835_mmal_video_qops = {
-+ .queue_setup = queue_setup,
-+ .buf_prepare = buffer_prepare,
-+ .buf_queue = buffer_queue,
-+ .start_streaming = start_streaming,
-+ .stop_streaming = stop_streaming,
-+ .wait_prepare = bm2835_mmal_unlock,
-+ .wait_finish = bm2835_mmal_lock,
-+};
-+
-+/* ------------------------------------------------------------------
-+ IOCTL operations
-+ ------------------------------------------------------------------*/
-+
-+/* overlay ioctl */
-+static int vidioc_enum_fmt_vid_overlay(struct file *file, void *priv,
-+ struct v4l2_fmtdesc *f)
-+{
-+ struct mmal_fmt *fmt;
-+
-+ if (f->index >= ARRAY_SIZE(formats))
-+ return -EINVAL;
-+
-+ fmt = &formats[f->index];
-+
-+ strlcpy(f->description, fmt->name, sizeof(f->description));
-+ f->pixelformat = fmt->fourcc;
-+ f->flags = fmt->flags;
-+
-+ return 0;
-+}
-+
-+static int vidioc_g_fmt_vid_overlay(struct file *file, void *priv,
-+ struct v4l2_format *f)
-+{
-+ struct bm2835_mmal_dev *dev = video_drvdata(file);
-+
-+ f->fmt.win = dev->overlay;
-+
-+ return 0;
-+}
-+
-+static int vidioc_try_fmt_vid_overlay(struct file *file, void *priv,
-+ struct v4l2_format *f)
-+{
-+ /* Only support one format so get the current one. */
-+ vidioc_g_fmt_vid_overlay(file, priv, f);
-+
-+ /* todo: allow the size and/or offset to be changed. */
-+ return 0;
-+}
-+
-+static int vidioc_s_fmt_vid_overlay(struct file *file, void *priv,
-+ struct v4l2_format *f)
-+{
-+ struct bm2835_mmal_dev *dev = video_drvdata(file);
-+
-+ vidioc_try_fmt_vid_overlay(file, priv, f);
-+
-+ dev->overlay = f->fmt.win;
-+
-+ /* todo: program the preview port parameters */
-+ return 0;
-+}
-+
-+static int vidioc_overlay(struct file *file, void *f, unsigned int on)
-+{
-+ int ret;
-+ struct bm2835_mmal_dev *dev = video_drvdata(file);
-+ struct vchiq_mmal_port *src;
-+ struct vchiq_mmal_port *dst;
-+ struct mmal_parameter_displayregion prev_config = {
-+ .set = MMAL_DISPLAY_SET_LAYER | MMAL_DISPLAY_SET_ALPHA |
-+ MMAL_DISPLAY_SET_DEST_RECT | MMAL_DISPLAY_SET_FULLSCREEN,
-+ .layer = PREVIEW_LAYER,
-+ .alpha = 255,
-+ .fullscreen = 0,
-+ .dest_rect = {
-+ .x = dev->overlay.w.left,
-+ .y = dev->overlay.w.top,
-+ .width = dev->overlay.w.width,
-+ .height = dev->overlay.w.height,
-+ },
-+ };
-+
-+ if ((on && dev->component[MMAL_COMPONENT_PREVIEW]->enabled) ||
-+ (!on && !dev->component[MMAL_COMPONENT_PREVIEW]->enabled))
-+ return 0; /* already in requested state */
-+
-+ src =
-+ &dev->component[MMAL_COMPONENT_CAMERA]->
-+ output[MMAL_CAMERA_PORT_PREVIEW];
-+
-+ if (!on) {
-+ /* disconnect preview ports and disable component */
-+ ret = vchiq_mmal_port_disable(dev->instance, src);
-+ if (!ret)
-+ ret =
-+ vchiq_mmal_port_connect_tunnel(dev->instance, src,
-+ NULL);
-+ if (ret >= 0)
-+ ret = vchiq_mmal_component_disable(
-+ dev->instance,
-+ dev->component[MMAL_COMPONENT_PREVIEW]);
-+
-+ disable_camera(dev);
-+ return ret;
-+ }
-+
-+ /* set preview port format and connect it to output */
-+ dst = &dev->component[MMAL_COMPONENT_PREVIEW]->input[0];
-+
-+ ret = vchiq_mmal_port_set_format(dev->instance, src);
-+ if (ret < 0)
-+ goto error;
-+
-+ ret = vchiq_mmal_port_parameter_set(dev->instance, dst,
-+ MMAL_PARAMETER_DISPLAYREGION,
-+ &prev_config, sizeof(prev_config));
-+ if (ret < 0)
-+ goto error;
-+
-+ if (enable_camera(dev) < 0)
-+ goto error;
-+
-+ ret = vchiq_mmal_component_enable(
-+ dev->instance,
-+ dev->component[MMAL_COMPONENT_PREVIEW]);
-+ if (ret < 0)
-+ goto error;
-+
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev, "connecting %p to %p\n",
-+ src, dst);
-+ ret = vchiq_mmal_port_connect_tunnel(dev->instance, src, dst);
-+ if (!ret)
-+ ret = vchiq_mmal_port_enable(dev->instance, src, NULL);
-+error:
-+ return ret;
-+}
-+
-+static int vidioc_g_fbuf(struct file *file, void *fh,
-+ struct v4l2_framebuffer *a)
-+{
-+ /* The video overlay must stay within the framebuffer and can't be
-+ positioned independently. */
-+ struct bm2835_mmal_dev *dev = video_drvdata(file);
-+ struct vchiq_mmal_port *preview_port =
-+ &dev->component[MMAL_COMPONENT_CAMERA]->
-+ output[MMAL_CAMERA_PORT_PREVIEW];
-+ a->flags = V4L2_FBUF_FLAG_OVERLAY;
-+ a->fmt.width = preview_port->es.video.width;
-+ a->fmt.height = preview_port->es.video.height;
-+ a->fmt.pixelformat = V4L2_PIX_FMT_YUV420;
-+ a->fmt.bytesperline = preview_port->es.video.width;
-+ a->fmt.sizeimage = (preview_port->es.video.width *
-+ preview_port->es.video.height * 3)>>1;
-+ a->fmt.colorspace = V4L2_COLORSPACE_SMPTE170M;
-+
-+ return 0;
-+}
-+
-+/* input ioctls */
-+static int vidioc_enum_input(struct file *file, void *priv,
-+ struct v4l2_input *inp)
-+{
-+ /* only a single camera input */
-+ if (inp->index != 0)
-+ return -EINVAL;
-+
-+ inp->type = V4L2_INPUT_TYPE_CAMERA;
-+ sprintf(inp->name, "Camera %u", inp->index);
-+ return 0;
-+}
-+
-+static int vidioc_g_input(struct file *file, void *priv, unsigned int *i)
-+{
-+ *i = 0;
-+ return 0;
-+}
-+
-+static int vidioc_s_input(struct file *file, void *priv, unsigned int i)
-+{
-+ if (i != 0)
-+ return -EINVAL;
-+
-+ return 0;
-+}
-+
-+/* capture ioctls */
-+static int vidioc_querycap(struct file *file, void *priv,
-+ struct v4l2_capability *cap)
-+{
-+ struct bm2835_mmal_dev *dev = video_drvdata(file);
-+ u32 major;
-+ u32 minor;
-+
-+ vchiq_mmal_version(dev->instance, &major, &minor);
-+
-+ strcpy(cap->driver, "bm2835 mmal");
-+ snprintf(cap->card, sizeof(cap->card), "mmal service %d.%d",
-+ major, minor);
-+
-+ snprintf(cap->bus_info, sizeof(cap->bus_info),
-+ "platform:%s", dev->v4l2_dev.name);
-+ cap->device_caps = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_VIDEO_OVERLAY |
-+ V4L2_CAP_STREAMING | V4L2_CAP_READWRITE;
-+ cap->capabilities = cap->device_caps | V4L2_CAP_DEVICE_CAPS;
-+
-+ return 0;
-+}
-+
-+static int vidioc_enum_fmt_vid_cap(struct file *file, void *priv,
-+ struct v4l2_fmtdesc *f)
-+{
-+ struct mmal_fmt *fmt;
-+
-+ if (f->index >= ARRAY_SIZE(formats))
-+ return -EINVAL;
-+
-+ fmt = &formats[f->index];
-+
-+ strlcpy(f->description, fmt->name, sizeof(f->description));
-+ f->pixelformat = fmt->fourcc;
-+ f->flags = fmt->flags;
-+
-+ return 0;
-+}
-+
-+static int vidioc_g_fmt_vid_cap(struct file *file, void *priv,
-+ struct v4l2_format *f)
-+{
-+ struct bm2835_mmal_dev *dev = video_drvdata(file);
-+
-+ f->fmt.pix.width = dev->capture.width;
-+ f->fmt.pix.height = dev->capture.height;
-+ f->fmt.pix.field = V4L2_FIELD_NONE;
-+ f->fmt.pix.pixelformat = dev->capture.fmt->fourcc;
-+ f->fmt.pix.bytesperline = dev->capture.stride;
-+ f->fmt.pix.sizeimage = dev->capture.buffersize;
-+
-+ if (dev->capture.fmt->fourcc == V4L2_PIX_FMT_RGB24)
-+ f->fmt.pix.colorspace = V4L2_COLORSPACE_SRGB;
-+ else if (dev->capture.fmt->fourcc == V4L2_PIX_FMT_JPEG)
-+ f->fmt.pix.colorspace = V4L2_COLORSPACE_JPEG;
-+ else
-+ f->fmt.pix.colorspace = V4L2_COLORSPACE_SMPTE170M;
-+ f->fmt.pix.priv = 0;
-+
-+ v4l2_dump_pix_format(1, bcm2835_v4l2_debug, &dev->v4l2_dev, &f->fmt.pix,
-+ __func__);
-+ return 0;
-+}
-+
-+static int vidioc_try_fmt_vid_cap(struct file *file, void *priv,
-+ struct v4l2_format *f)
-+{
-+ struct bm2835_mmal_dev *dev = video_drvdata(file);
-+ struct mmal_fmt *mfmt;
-+
-+ mfmt = get_format(f);
-+ if (!mfmt) {
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "Fourcc format (0x%08x) unknown.\n",
-+ f->fmt.pix.pixelformat);
-+ f->fmt.pix.pixelformat = formats[0].fourcc;
-+ mfmt = get_format(f);
-+ }
-+
-+ f->fmt.pix.field = V4L2_FIELD_NONE;
-+
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "Clipping/aligning %dx%d format %08X\n",
-+ f->fmt.pix.width, f->fmt.pix.height, f->fmt.pix.pixelformat);
-+
-+ v4l_bound_align_image(&f->fmt.pix.width, MIN_WIDTH, MAX_WIDTH, 1,
-+ &f->fmt.pix.height, MIN_HEIGHT, MAX_HEIGHT, 1, 0);
-+ f->fmt.pix.bytesperline = f->fmt.pix.width * mfmt->ybbp;
-+
-+ /* Image buffer has to be padded to allow for alignment, even though
-+ * we then remove that padding before delivering the buffer.
-+ */
-+ f->fmt.pix.sizeimage = ((f->fmt.pix.height+15)&~15) *
-+ (((f->fmt.pix.width+31)&~31) * mfmt->depth) >> 3;
-+
-+ if ((mfmt->flags & V4L2_FMT_FLAG_COMPRESSED) &&
-+ f->fmt.pix.sizeimage < MIN_BUFFER_SIZE)
-+ f->fmt.pix.sizeimage = MIN_BUFFER_SIZE;
-+
-+ if (f->fmt.pix.pixelformat == V4L2_PIX_FMT_RGB24)
-+ f->fmt.pix.colorspace = V4L2_COLORSPACE_SRGB;
-+ else if (f->fmt.pix.pixelformat == V4L2_PIX_FMT_JPEG)
-+ f->fmt.pix.colorspace = V4L2_COLORSPACE_JPEG;
-+ else
-+ f->fmt.pix.colorspace = V4L2_COLORSPACE_SMPTE170M;
-+ f->fmt.pix.priv = 0;
-+
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "Now %dx%d format %08X\n",
-+ f->fmt.pix.width, f->fmt.pix.height, f->fmt.pix.pixelformat);
-+
-+ v4l2_dump_pix_format(1, bcm2835_v4l2_debug, &dev->v4l2_dev, &f->fmt.pix,
-+ __func__);
-+ return 0;
-+}
-+
-+static int mmal_setup_components(struct bm2835_mmal_dev *dev,
-+ struct v4l2_format *f)
-+{
-+ int ret;
-+ struct vchiq_mmal_port *port = NULL, *camera_port = NULL;
-+ struct vchiq_mmal_component *encode_component = NULL;
-+ struct mmal_fmt *mfmt = get_format(f);
-+
-+ BUG_ON(!mfmt);
-+
-+ if (dev->capture.encode_component) {
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "vid_cap - disconnect previous tunnel\n");
-+
-+ /* Disconnect any previous connection */
-+ vchiq_mmal_port_connect_tunnel(dev->instance,
-+ dev->capture.camera_port, NULL);
-+ dev->capture.camera_port = NULL;
-+ ret = vchiq_mmal_component_disable(dev->instance,
-+ dev->capture.
-+ encode_component);
-+ if (ret)
-+ v4l2_err(&dev->v4l2_dev,
-+ "Failed to disable encode component %d\n",
-+ ret);
-+
-+ dev->capture.encode_component = NULL;
-+ }
-+ /* format dependant port setup */
-+ switch (mfmt->mmal_component) {
-+ case MMAL_COMPONENT_CAMERA:
-+ /* Make a further decision on port based on resolution */
-+ if (f->fmt.pix.width <= max_video_width
-+ && f->fmt.pix.height <= max_video_height)
-+ camera_port = port =
-+ &dev->component[MMAL_COMPONENT_CAMERA]->
-+ output[MMAL_CAMERA_PORT_VIDEO];
-+ else
-+ camera_port = port =
-+ &dev->component[MMAL_COMPONENT_CAMERA]->
-+ output[MMAL_CAMERA_PORT_CAPTURE];
-+ break;
-+ case MMAL_COMPONENT_IMAGE_ENCODE:
-+ encode_component = dev->component[MMAL_COMPONENT_IMAGE_ENCODE];
-+ port = &dev->component[MMAL_COMPONENT_IMAGE_ENCODE]->output[0];
-+ camera_port =
-+ &dev->component[MMAL_COMPONENT_CAMERA]->
-+ output[MMAL_CAMERA_PORT_CAPTURE];
-+ break;
-+ case MMAL_COMPONENT_VIDEO_ENCODE:
-+ encode_component = dev->component[MMAL_COMPONENT_VIDEO_ENCODE];
-+ port = &dev->component[MMAL_COMPONENT_VIDEO_ENCODE]->output[0];
-+ camera_port =
-+ &dev->component[MMAL_COMPONENT_CAMERA]->
-+ output[MMAL_CAMERA_PORT_VIDEO];
-+ break;
-+ default:
-+ break;
-+ }
-+
-+ if (!port)
-+ return -EINVAL;
-+
-+ if (encode_component)
-+ camera_port->format.encoding = MMAL_ENCODING_OPAQUE;
-+ else
-+ camera_port->format.encoding = mfmt->mmal;
-+
-+ camera_port->format.encoding_variant = 0;
-+ camera_port->es.video.width = f->fmt.pix.width;
-+ camera_port->es.video.height = f->fmt.pix.height;
-+ camera_port->es.video.crop.x = 0;
-+ camera_port->es.video.crop.y = 0;
-+ camera_port->es.video.crop.width = f->fmt.pix.width;
-+ camera_port->es.video.crop.height = f->fmt.pix.height;
-+ camera_port->es.video.frame_rate.num = 0;
-+ camera_port->es.video.frame_rate.den = 1;
-+ camera_port->es.video.color_space = MMAL_COLOR_SPACE_JPEG_JFIF;
-+
-+ ret = vchiq_mmal_port_set_format(dev->instance, camera_port);
-+
-+ if (!ret
-+ && camera_port ==
-+ &dev->component[MMAL_COMPONENT_CAMERA]->
-+ output[MMAL_CAMERA_PORT_VIDEO]) {
-+ bool overlay_enabled =
-+ !!dev->component[MMAL_COMPONENT_PREVIEW]->enabled;
-+ struct vchiq_mmal_port *preview_port =
-+ &dev->component[MMAL_COMPONENT_CAMERA]->
-+ output[MMAL_CAMERA_PORT_PREVIEW];
-+ /* Preview and encode ports need to match on resolution */
-+ if (overlay_enabled) {
-+ /* Need to disable the overlay before we can update
-+ * the resolution
-+ */
-+ ret =
-+ vchiq_mmal_port_disable(dev->instance,
-+ preview_port);
-+ if (!ret)
-+ ret =
-+ vchiq_mmal_port_connect_tunnel(
-+ dev->instance,
-+ preview_port,
-+ NULL);
-+ }
-+ preview_port->es.video.width = f->fmt.pix.width;
-+ preview_port->es.video.height = f->fmt.pix.height;
-+ preview_port->es.video.crop.x = 0;
-+ preview_port->es.video.crop.y = 0;
-+ preview_port->es.video.crop.width = f->fmt.pix.width;
-+ preview_port->es.video.crop.height = f->fmt.pix.height;
-+ preview_port->es.video.frame_rate.num =
-+ dev->capture.timeperframe.denominator;
-+ preview_port->es.video.frame_rate.den =
-+ dev->capture.timeperframe.numerator;
-+ ret = vchiq_mmal_port_set_format(dev->instance, preview_port);
-+ if (overlay_enabled) {
-+ ret = vchiq_mmal_port_connect_tunnel(
-+ dev->instance,
-+ preview_port,
-+ &dev->component[MMAL_COMPONENT_PREVIEW]->input[0]);
-+ if (!ret)
-+ ret = vchiq_mmal_port_enable(dev->instance,
-+ preview_port,
-+ NULL);
-+ }
-+ }
-+
-+ if (ret) {
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "%s failed to set format %dx%d %08X\n", __func__,
-+ f->fmt.pix.width, f->fmt.pix.height,
-+ f->fmt.pix.pixelformat);
-+ /* ensure capture is not going to be tried */
-+ dev->capture.port = NULL;
-+ } else {
-+ if (encode_component) {
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "vid_cap - set up encode comp\n");
-+
-+ /* configure buffering */
-+ camera_port->current_buffer.size =
-+ camera_port->recommended_buffer.size;
-+ camera_port->current_buffer.num =
-+ camera_port->recommended_buffer.num;
-+
-+ ret =
-+ vchiq_mmal_port_connect_tunnel(
-+ dev->instance,
-+ camera_port,
-+ &encode_component->input[0]);
-+ if (ret) {
-+ v4l2_dbg(1, bcm2835_v4l2_debug,
-+ &dev->v4l2_dev,
-+ "%s failed to create connection\n",
-+ __func__);
-+ /* ensure capture is not going to be tried */
-+ dev->capture.port = NULL;
-+ } else {
-+ port->es.video.width = f->fmt.pix.width;
-+ port->es.video.height = f->fmt.pix.height;
-+ port->es.video.crop.x = 0;
-+ port->es.video.crop.y = 0;
-+ port->es.video.crop.width = f->fmt.pix.width;
-+ port->es.video.crop.height = f->fmt.pix.height;
-+ port->es.video.frame_rate.num =
-+ dev->capture.timeperframe.denominator;
-+ port->es.video.frame_rate.den =
-+ dev->capture.timeperframe.numerator;
-+
-+ port->format.encoding = mfmt->mmal;
-+ port->format.encoding_variant = 0;
-+ /* Set any encoding specific parameters */
-+ switch (mfmt->mmal_component) {
-+ case MMAL_COMPONENT_VIDEO_ENCODE:
-+ port->format.bitrate =
-+ dev->capture.encode_bitrate;
-+ break;
-+ case MMAL_COMPONENT_IMAGE_ENCODE:
-+ /* Could set EXIF parameters here */
-+ break;
-+ default:
-+ break;
-+ }
-+ ret = vchiq_mmal_port_set_format(dev->instance,
-+ port);
-+ if (ret)
-+ v4l2_dbg(1, bcm2835_v4l2_debug,
-+ &dev->v4l2_dev,
-+ "%s failed to set format %dx%d fmt %08X\n",
-+ __func__,
-+ f->fmt.pix.width,
-+ f->fmt.pix.height,
-+ f->fmt.pix.pixelformat
-+ );
-+ }
-+
-+ if (!ret) {
-+ ret = vchiq_mmal_component_enable(
-+ dev->instance,
-+ encode_component);
-+ if (ret) {
-+ v4l2_dbg(1, bcm2835_v4l2_debug,
-+ &dev->v4l2_dev,
-+ "%s Failed to enable encode components\n",
-+ __func__);
-+ }
-+ }
-+ if (!ret) {
-+ /* configure buffering */
-+ port->current_buffer.num = 1;
-+ port->current_buffer.size =
-+ f->fmt.pix.sizeimage;
-+ if (port->format.encoding ==
-+ MMAL_ENCODING_JPEG) {
-+ v4l2_dbg(1, bcm2835_v4l2_debug,
-+ &dev->v4l2_dev,
-+ "JPG - buf size now %d was %d\n",
-+ f->fmt.pix.sizeimage,
-+ port->current_buffer.size);
-+ port->current_buffer.size =
-+ (f->fmt.pix.sizeimage <
-+ (100 << 10))
-+ ? (100 << 10) : f->fmt.pix.
-+ sizeimage;
-+ }
-+ v4l2_dbg(1, bcm2835_v4l2_debug,
-+ &dev->v4l2_dev,
-+ "vid_cap - cur_buf.size set to %d\n",
-+ f->fmt.pix.sizeimage);
-+ port->current_buffer.alignment = 0;
-+ }
-+ } else {
-+ /* configure buffering */
-+ camera_port->current_buffer.num = 1;
-+ camera_port->current_buffer.size = f->fmt.pix.sizeimage;
-+ camera_port->current_buffer.alignment = 0;
-+ }
-+
-+ if (!ret) {
-+ dev->capture.fmt = mfmt;
-+ dev->capture.stride = f->fmt.pix.bytesperline;
-+ dev->capture.width = camera_port->es.video.crop.width;
-+ dev->capture.height = camera_port->es.video.crop.height;
-+ dev->capture.buffersize = port->current_buffer.size;
-+
-+ /* select port for capture */
-+ dev->capture.port = port;
-+ dev->capture.camera_port = camera_port;
-+ dev->capture.encode_component = encode_component;
-+ v4l2_dbg(1, bcm2835_v4l2_debug,
-+ &dev->v4l2_dev,
-+ "Set dev->capture.fmt %08X, %dx%d, stride %d, size %d",
-+ port->format.encoding,
-+ dev->capture.width, dev->capture.height,
-+ dev->capture.stride, dev->capture.buffersize);
-+ }
-+ }
-+
-+ /* todo: Need to convert the vchiq/mmal error into a v4l2 error. */
-+ return ret;
-+}
-+
-+static int vidioc_s_fmt_vid_cap(struct file *file, void *priv,
-+ struct v4l2_format *f)
-+{
-+ int ret;
-+ struct bm2835_mmal_dev *dev = video_drvdata(file);
-+ struct mmal_fmt *mfmt;
-+
-+ /* try the format to set valid parameters */
-+ ret = vidioc_try_fmt_vid_cap(file, priv, f);
-+ if (ret) {
-+ v4l2_err(&dev->v4l2_dev,
-+ "vid_cap - vidioc_try_fmt_vid_cap failed\n");
-+ return ret;
-+ }
-+
-+ /* if a capture is running refuse to set format */
-+ if (vb2_is_busy(&dev->capture.vb_vidq)) {
-+ v4l2_info(&dev->v4l2_dev, "%s device busy\n", __func__);
-+ return -EBUSY;
-+ }
-+
-+ /* If the format is unsupported v4l2 says we should switch to
-+ * a supported one and not return an error. */
-+ mfmt = get_format(f);
-+ if (!mfmt) {
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "Fourcc format (0x%08x) unknown.\n",
-+ f->fmt.pix.pixelformat);
-+ f->fmt.pix.pixelformat = formats[0].fourcc;
-+ mfmt = get_format(f);
-+ }
-+
-+ ret = mmal_setup_components(dev, f);
-+ if (ret != 0) {
-+ v4l2_err(&dev->v4l2_dev,
-+ "%s: failed to setup mmal components: %d\n",
-+ __func__, ret);
-+ ret = -EINVAL;
-+ }
-+
-+ return ret;
-+}
-+
-+int vidioc_enum_framesizes(struct file *file, void *fh,
-+ struct v4l2_frmsizeenum *fsize)
-+{
-+ static const struct v4l2_frmsize_stepwise sizes = {
-+ MIN_WIDTH, MAX_WIDTH, 2,
-+ MIN_HEIGHT, MAX_HEIGHT, 2
-+ };
-+ int i;
-+
-+ if (fsize->index)
-+ return -EINVAL;
-+ for (i = 0; i < ARRAY_SIZE(formats); i++)
-+ if (formats[i].fourcc == fsize->pixel_format)
-+ break;
-+ if (i == ARRAY_SIZE(formats))
-+ return -EINVAL;
-+ fsize->type = V4L2_FRMSIZE_TYPE_STEPWISE;
-+ fsize->stepwise = sizes;
-+ return 0;
-+}
-+
-+/* timeperframe is arbitrary and continous */
-+static int vidioc_enum_frameintervals(struct file *file, void *priv,
-+ struct v4l2_frmivalenum *fival)
-+{
-+ int i;
-+
-+ if (fival->index)
-+ return -EINVAL;
-+
-+ for (i = 0; i < ARRAY_SIZE(formats); i++)
-+ if (formats[i].fourcc == fival->pixel_format)
-+ break;
-+ if (i == ARRAY_SIZE(formats))
-+ return -EINVAL;
-+
-+ /* regarding width & height - we support any within range */
-+ if (fival->width < MIN_WIDTH || fival->width > MAX_WIDTH ||
-+ fival->height < MIN_HEIGHT || fival->height > MAX_HEIGHT)
-+ return -EINVAL;
-+
-+ fival->type = V4L2_FRMIVAL_TYPE_CONTINUOUS;
-+
-+ /* fill in stepwise (step=1.0 is requred by V4L2 spec) */
-+ fival->stepwise.min = tpf_min;
-+ fival->stepwise.max = tpf_max;
-+ fival->stepwise.step = (struct v4l2_fract) {1, 1};
-+
-+ return 0;
-+}
-+
-+static int vidioc_g_parm(struct file *file, void *priv,
-+ struct v4l2_streamparm *parm)
-+{
-+ struct bm2835_mmal_dev *dev = video_drvdata(file);
-+
-+ if (parm->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
-+ return -EINVAL;
-+
-+ parm->parm.capture.capability = V4L2_CAP_TIMEPERFRAME;
-+ parm->parm.capture.timeperframe = dev->capture.timeperframe;
-+ parm->parm.capture.readbuffers = 1;
-+ return 0;
-+}
-+
-+#define FRACT_CMP(a, OP, b) \
-+ ((u64)(a).numerator * (b).denominator OP \
-+ (u64)(b).numerator * (a).denominator)
-+
-+static int vidioc_s_parm(struct file *file, void *priv,
-+ struct v4l2_streamparm *parm)
-+{
-+ struct bm2835_mmal_dev *dev = video_drvdata(file);
-+ struct v4l2_fract tpf;
-+ struct mmal_parameter_rational fps_param;
-+
-+ if (parm->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
-+ return -EINVAL;
-+
-+ tpf = parm->parm.capture.timeperframe;
-+
-+ /* tpf: {*, 0} resets timing; clip to [min, max]*/
-+ tpf = tpf.denominator ? tpf : tpf_default;
-+ tpf = FRACT_CMP(tpf, <, tpf_min) ? tpf_min : tpf;
-+ tpf = FRACT_CMP(tpf, >, tpf_max) ? tpf_max : tpf;
-+
-+ dev->capture.timeperframe = tpf;
-+ parm->parm.capture.timeperframe = tpf;
-+ parm->parm.capture.readbuffers = 1;
-+
-+ fps_param.num = 0; /* Select variable fps, and then use
-+ * FPS_RANGE to select the actual limits.
-+ */
-+ fps_param.den = 1;
-+ set_framerate_params(dev);
-+
-+ return 0;
-+}
-+
-+static const struct v4l2_ioctl_ops camera0_ioctl_ops = {
-+ /* overlay */
-+ .vidioc_enum_fmt_vid_overlay = vidioc_enum_fmt_vid_overlay,
-+ .vidioc_g_fmt_vid_overlay = vidioc_g_fmt_vid_overlay,
-+ .vidioc_try_fmt_vid_overlay = vidioc_try_fmt_vid_overlay,
-+ .vidioc_s_fmt_vid_overlay = vidioc_s_fmt_vid_overlay,
-+ .vidioc_overlay = vidioc_overlay,
-+ .vidioc_g_fbuf = vidioc_g_fbuf,
-+
-+ /* inputs */
-+ .vidioc_enum_input = vidioc_enum_input,
-+ .vidioc_g_input = vidioc_g_input,
-+ .vidioc_s_input = vidioc_s_input,
-+
-+ /* capture */
-+ .vidioc_querycap = vidioc_querycap,
-+ .vidioc_enum_fmt_vid_cap = vidioc_enum_fmt_vid_cap,
-+ .vidioc_g_fmt_vid_cap = vidioc_g_fmt_vid_cap,
-+ .vidioc_try_fmt_vid_cap = vidioc_try_fmt_vid_cap,
-+ .vidioc_s_fmt_vid_cap = vidioc_s_fmt_vid_cap,
-+
-+ /* buffer management */
-+ .vidioc_reqbufs = vb2_ioctl_reqbufs,
-+ .vidioc_create_bufs = vb2_ioctl_create_bufs,
-+ .vidioc_prepare_buf = vb2_ioctl_prepare_buf,
-+ .vidioc_querybuf = vb2_ioctl_querybuf,
-+ .vidioc_qbuf = vb2_ioctl_qbuf,
-+ .vidioc_dqbuf = vb2_ioctl_dqbuf,
-+ .vidioc_enum_framesizes = vidioc_enum_framesizes,
-+ .vidioc_enum_frameintervals = vidioc_enum_frameintervals,
-+ .vidioc_g_parm = vidioc_g_parm,
-+ .vidioc_s_parm = vidioc_s_parm,
-+ .vidioc_streamon = vb2_ioctl_streamon,
-+ .vidioc_streamoff = vb2_ioctl_streamoff,
-+
-+ .vidioc_log_status = v4l2_ctrl_log_status,
-+ .vidioc_subscribe_event = v4l2_ctrl_subscribe_event,
-+ .vidioc_unsubscribe_event = v4l2_event_unsubscribe,
-+};
-+
-+static const struct v4l2_ioctl_ops camera0_ioctl_ops_gstreamer = {
-+ /* overlay */
-+ .vidioc_enum_fmt_vid_overlay = vidioc_enum_fmt_vid_overlay,
-+ .vidioc_g_fmt_vid_overlay = vidioc_g_fmt_vid_overlay,
-+ .vidioc_try_fmt_vid_overlay = vidioc_try_fmt_vid_overlay,
-+ .vidioc_s_fmt_vid_overlay = vidioc_s_fmt_vid_overlay,
-+ .vidioc_overlay = vidioc_overlay,
-+ .vidioc_g_fbuf = vidioc_g_fbuf,
-+
-+ /* inputs */
-+ .vidioc_enum_input = vidioc_enum_input,
-+ .vidioc_g_input = vidioc_g_input,
-+ .vidioc_s_input = vidioc_s_input,
-+
-+ /* capture */
-+ .vidioc_querycap = vidioc_querycap,
-+ .vidioc_enum_fmt_vid_cap = vidioc_enum_fmt_vid_cap,
-+ .vidioc_g_fmt_vid_cap = vidioc_g_fmt_vid_cap,
-+ .vidioc_try_fmt_vid_cap = vidioc_try_fmt_vid_cap,
-+ .vidioc_s_fmt_vid_cap = vidioc_s_fmt_vid_cap,
-+
-+ /* buffer management */
-+ .vidioc_reqbufs = vb2_ioctl_reqbufs,
-+ .vidioc_create_bufs = vb2_ioctl_create_bufs,
-+ .vidioc_prepare_buf = vb2_ioctl_prepare_buf,
-+ .vidioc_querybuf = vb2_ioctl_querybuf,
-+ .vidioc_qbuf = vb2_ioctl_qbuf,
-+ .vidioc_dqbuf = vb2_ioctl_dqbuf,
-+ /* Remove this function ptr to fix gstreamer bug
-+ .vidioc_enum_framesizes = vidioc_enum_framesizes, */
-+ .vidioc_enum_frameintervals = vidioc_enum_frameintervals,
-+ .vidioc_g_parm = vidioc_g_parm,
-+ .vidioc_s_parm = vidioc_s_parm,
-+ .vidioc_streamon = vb2_ioctl_streamon,
-+ .vidioc_streamoff = vb2_ioctl_streamoff,
-+
-+ .vidioc_log_status = v4l2_ctrl_log_status,
-+ .vidioc_subscribe_event = v4l2_ctrl_subscribe_event,
-+ .vidioc_unsubscribe_event = v4l2_event_unsubscribe,
-+};
-+
-+/* ------------------------------------------------------------------
-+ Driver init/finalise
-+ ------------------------------------------------------------------*/
-+
-+static const struct v4l2_file_operations camera0_fops = {
-+ .owner = THIS_MODULE,
-+ .open = v4l2_fh_open,
-+ .release = vb2_fop_release,
-+ .read = vb2_fop_read,
-+ .poll = vb2_fop_poll,
-+ .unlocked_ioctl = video_ioctl2, /* V4L2 ioctl handler */
-+ .mmap = vb2_fop_mmap,
-+};
-+
-+static struct video_device vdev_template = {
-+ .name = "camera0",
-+ .fops = &camera0_fops,
-+ .ioctl_ops = &camera0_ioctl_ops,
-+ .release = video_device_release_empty,
-+};
-+
-+static int set_camera_parameters(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_component *camera)
-+{
-+ int ret;
-+ struct mmal_parameter_camera_config cam_config = {
-+ .max_stills_w = MAX_WIDTH,
-+ .max_stills_h = MAX_HEIGHT,
-+ .stills_yuv422 = 1,
-+ .one_shot_stills = 1,
-+ .max_preview_video_w = (max_video_width > 1920) ?
-+ max_video_width : 1920,
-+ .max_preview_video_h = (max_video_height > 1088) ?
-+ max_video_height : 1088,
-+ .num_preview_video_frames = 3,
-+ .stills_capture_circular_buffer_height = 0,
-+ .fast_preview_resume = 0,
-+ .use_stc_timestamp = MMAL_PARAM_TIMESTAMP_MODE_RAW_STC
-+ };
-+
-+ ret = vchiq_mmal_port_parameter_set(instance, &camera->control,
-+ MMAL_PARAMETER_CAMERA_CONFIG,
-+ &cam_config, sizeof(cam_config));
-+ return ret;
-+}
-+
-+/* MMAL instance and component init */
-+static int __init mmal_init(struct bm2835_mmal_dev *dev)
-+{
-+ int ret;
-+ struct mmal_es_format *format;
-+ u32 bool_true = 1;
-+
-+ ret = vchiq_mmal_init(&dev->instance);
-+ if (ret < 0)
-+ return ret;
-+
-+ /* get the camera component ready */
-+ ret = vchiq_mmal_component_init(dev->instance, "ril.camera",
-+ &dev->component[MMAL_COMPONENT_CAMERA]);
-+ if (ret < 0)
-+ goto unreg_mmal;
-+
-+ if (dev->component[MMAL_COMPONENT_CAMERA]->outputs <
-+ MMAL_CAMERA_PORT_COUNT) {
-+ ret = -EINVAL;
-+ goto unreg_camera;
-+ }
-+
-+ ret = set_camera_parameters(dev->instance,
-+ dev->component[MMAL_COMPONENT_CAMERA]);
-+ if (ret < 0)
-+ goto unreg_camera;
-+
-+ format =
-+ &dev->component[MMAL_COMPONENT_CAMERA]->
-+ output[MMAL_CAMERA_PORT_PREVIEW].format;
-+
-+ format->encoding = MMAL_ENCODING_OPAQUE;
-+ format->encoding_variant = MMAL_ENCODING_I420;
-+
-+ format->es->video.width = 1024;
-+ format->es->video.height = 768;
-+ format->es->video.crop.x = 0;
-+ format->es->video.crop.y = 0;
-+ format->es->video.crop.width = 1024;
-+ format->es->video.crop.height = 768;
-+ format->es->video.frame_rate.num = 0; /* Rely on fps_range */
-+ format->es->video.frame_rate.den = 1;
-+
-+ format =
-+ &dev->component[MMAL_COMPONENT_CAMERA]->
-+ output[MMAL_CAMERA_PORT_VIDEO].format;
-+
-+ format->encoding = MMAL_ENCODING_OPAQUE;
-+ format->encoding_variant = MMAL_ENCODING_I420;
-+
-+ format->es->video.width = 1024;
-+ format->es->video.height = 768;
-+ format->es->video.crop.x = 0;
-+ format->es->video.crop.y = 0;
-+ format->es->video.crop.width = 1024;
-+ format->es->video.crop.height = 768;
-+ format->es->video.frame_rate.num = 0; /* Rely on fps_range */
-+ format->es->video.frame_rate.den = 1;
-+
-+ vchiq_mmal_port_parameter_set(dev->instance,
-+ &dev->component[MMAL_COMPONENT_CAMERA]->
-+ output[MMAL_CAMERA_PORT_VIDEO],
-+ MMAL_PARAMETER_NO_IMAGE_PADDING,
-+ &bool_true, sizeof(bool_true));
-+
-+ format =
-+ &dev->component[MMAL_COMPONENT_CAMERA]->
-+ output[MMAL_CAMERA_PORT_CAPTURE].format;
-+
-+ format->encoding = MMAL_ENCODING_OPAQUE;
-+
-+ format->es->video.width = 2592;
-+ format->es->video.height = 1944;
-+ format->es->video.crop.x = 0;
-+ format->es->video.crop.y = 0;
-+ format->es->video.crop.width = 2592;
-+ format->es->video.crop.height = 1944;
-+ format->es->video.frame_rate.num = 0; /* Rely on fps_range */
-+ format->es->video.frame_rate.den = 1;
-+
-+ dev->capture.width = format->es->video.width;
-+ dev->capture.height = format->es->video.height;
-+ dev->capture.fmt = &formats[0];
-+ dev->capture.encode_component = NULL;
-+ dev->capture.timeperframe = tpf_default;
-+ dev->capture.enc_profile = V4L2_MPEG_VIDEO_H264_PROFILE_HIGH;
-+ dev->capture.enc_level = V4L2_MPEG_VIDEO_H264_LEVEL_4_0;
-+
-+ vchiq_mmal_port_parameter_set(dev->instance,
-+ &dev->component[MMAL_COMPONENT_CAMERA]->
-+ output[MMAL_CAMERA_PORT_CAPTURE],
-+ MMAL_PARAMETER_NO_IMAGE_PADDING,
-+ &bool_true, sizeof(bool_true));
-+
-+ /* get the preview component ready */
-+ ret = vchiq_mmal_component_init(
-+ dev->instance, "ril.video_render",
-+ &dev->component[MMAL_COMPONENT_PREVIEW]);
-+ if (ret < 0)
-+ goto unreg_camera;
-+
-+ if (dev->component[MMAL_COMPONENT_PREVIEW]->inputs < 1) {
-+ ret = -EINVAL;
-+ pr_debug("too few input ports %d needed %d\n",
-+ dev->component[MMAL_COMPONENT_PREVIEW]->inputs, 1);
-+ goto unreg_preview;
-+ }
-+
-+ /* get the image encoder component ready */
-+ ret = vchiq_mmal_component_init(
-+ dev->instance, "ril.image_encode",
-+ &dev->component[MMAL_COMPONENT_IMAGE_ENCODE]);
-+ if (ret < 0)
-+ goto unreg_preview;
-+
-+ if (dev->component[MMAL_COMPONENT_IMAGE_ENCODE]->inputs < 1) {
-+ ret = -EINVAL;
-+ v4l2_err(&dev->v4l2_dev, "too few input ports %d needed %d\n",
-+ dev->component[MMAL_COMPONENT_IMAGE_ENCODE]->inputs,
-+ 1);
-+ goto unreg_image_encoder;
-+ }
-+
-+ /* get the video encoder component ready */
-+ ret = vchiq_mmal_component_init(dev->instance, "ril.video_encode",
-+ &dev->
-+ component[MMAL_COMPONENT_VIDEO_ENCODE]);
-+ if (ret < 0)
-+ goto unreg_image_encoder;
-+
-+ if (dev->component[MMAL_COMPONENT_VIDEO_ENCODE]->inputs < 1) {
-+ ret = -EINVAL;
-+ v4l2_err(&dev->v4l2_dev, "too few input ports %d needed %d\n",
-+ dev->component[MMAL_COMPONENT_VIDEO_ENCODE]->inputs,
-+ 1);
-+ goto unreg_vid_encoder;
-+ }
-+
-+ {
-+ struct vchiq_mmal_port *encoder_port =
-+ &dev->component[MMAL_COMPONENT_VIDEO_ENCODE]->output[0];
-+ encoder_port->format.encoding = MMAL_ENCODING_H264;
-+ ret = vchiq_mmal_port_set_format(dev->instance,
-+ encoder_port);
-+ }
-+
-+ {
-+ unsigned int enable = 1;
-+ vchiq_mmal_port_parameter_set(
-+ dev->instance,
-+ &dev->component[MMAL_COMPONENT_VIDEO_ENCODE]->control,
-+ MMAL_PARAMETER_VIDEO_IMMUTABLE_INPUT,
-+ &enable, sizeof(enable));
-+
-+ vchiq_mmal_port_parameter_set(dev->instance,
-+ &dev->component[MMAL_COMPONENT_VIDEO_ENCODE]->control,
-+ MMAL_PARAMETER_MINIMISE_FRAGMENTATION,
-+ &enable,
-+ sizeof(enable));
-+ }
-+ ret = bm2835_mmal_set_all_camera_controls(dev);
-+ if (ret < 0)
-+ goto unreg_vid_encoder;
-+
-+ return 0;
-+
-+unreg_vid_encoder:
-+ pr_err("Cleanup: Destroy video encoder\n");
-+ vchiq_mmal_component_finalise(
-+ dev->instance,
-+ dev->component[MMAL_COMPONENT_VIDEO_ENCODE]);
-+
-+unreg_image_encoder:
-+ pr_err("Cleanup: Destroy image encoder\n");
-+ vchiq_mmal_component_finalise(
-+ dev->instance,
-+ dev->component[MMAL_COMPONENT_IMAGE_ENCODE]);
-+
-+unreg_preview:
-+ pr_err("Cleanup: Destroy video render\n");
-+ vchiq_mmal_component_finalise(dev->instance,
-+ dev->component[MMAL_COMPONENT_PREVIEW]);
-+
-+unreg_camera:
-+ pr_err("Cleanup: Destroy camera\n");
-+ vchiq_mmal_component_finalise(dev->instance,
-+ dev->component[MMAL_COMPONENT_CAMERA]);
-+
-+unreg_mmal:
-+ vchiq_mmal_finalise(dev->instance);
-+ return ret;
-+}
-+
-+static int __init bm2835_mmal_init_device(struct bm2835_mmal_dev *dev,
-+ struct video_device *vfd)
-+{
-+ int ret;
-+
-+ *vfd = vdev_template;
-+ if (gst_v4l2src_is_broken) {
-+ v4l2_info(&dev->v4l2_dev,
-+ "Work-around for gstreamer issue is active.\n");
-+ vfd->ioctl_ops = &camera0_ioctl_ops_gstreamer;
-+ }
-+
-+ vfd->v4l2_dev = &dev->v4l2_dev;
-+
-+ vfd->lock = &dev->mutex;
-+
-+ vfd->queue = &dev->capture.vb_vidq;
-+
-+ /* video device needs to be able to access instance data */
-+ video_set_drvdata(vfd, dev);
-+
-+ ret = video_register_device(vfd, VFL_TYPE_GRABBER, -1);
-+ if (ret < 0)
-+ return ret;
-+
-+ v4l2_info(vfd->v4l2_dev,
-+ "V4L2 device registered as %s - stills mode > %dx%d\n",
-+ video_device_node_name(vfd), max_video_width, max_video_height);
-+
-+ return 0;
-+}
-+
-+static struct v4l2_format default_v4l2_format = {
-+ .fmt.pix.pixelformat = V4L2_PIX_FMT_JPEG,
-+ .fmt.pix.width = 1024,
-+ .fmt.pix.bytesperline = 1024,
-+ .fmt.pix.height = 768,
-+ .fmt.pix.sizeimage = 1024*768,
-+};
-+
-+static int __init bm2835_mmal_init(void)
-+{
-+ int ret;
-+ struct bm2835_mmal_dev *dev;
-+ struct vb2_queue *q;
-+
-+ dev = kzalloc(sizeof(*gdev), GFP_KERNEL);
-+ if (!dev)
-+ return -ENOMEM;
-+
-+ /* setup device defaults */
-+ dev->overlay.w.left = 150;
-+ dev->overlay.w.top = 50;
-+ dev->overlay.w.width = 1024;
-+ dev->overlay.w.height = 768;
-+ dev->overlay.clipcount = 0;
-+ dev->overlay.field = V4L2_FIELD_NONE;
-+
-+ dev->capture.fmt = &formats[3]; /* JPEG */
-+
-+ /* v4l device registration */
-+ snprintf(dev->v4l2_dev.name, sizeof(dev->v4l2_dev.name),
-+ "%s", BM2835_MMAL_MODULE_NAME);
-+ ret = v4l2_device_register(NULL, &dev->v4l2_dev);
-+ if (ret)
-+ goto free_dev;
-+
-+ /* setup v4l controls */
-+ ret = bm2835_mmal_init_controls(dev, &dev->ctrl_handler);
-+ if (ret < 0)
-+ goto unreg_dev;
-+ dev->v4l2_dev.ctrl_handler = &dev->ctrl_handler;
-+
-+ /* mmal init */
-+ ret = mmal_init(dev);
-+ if (ret < 0)
-+ goto unreg_dev;
-+
-+ /* initialize queue */
-+ q = &dev->capture.vb_vidq;
-+ memset(q, 0, sizeof(*q));
-+ q->type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
-+ q->io_modes = VB2_MMAP | VB2_USERPTR | VB2_READ;
-+ q->drv_priv = dev;
-+ q->buf_struct_size = sizeof(struct mmal_buffer);
-+ q->ops = &bm2835_mmal_video_qops;
-+ q->mem_ops = &vb2_vmalloc_memops;
-+ q->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC;
-+ ret = vb2_queue_init(q);
-+ if (ret < 0)
-+ goto unreg_dev;
-+
-+ /* v4l2 core mutex used to protect all fops and v4l2 ioctls. */
-+ mutex_init(&dev->mutex);
-+
-+ /* initialise video devices */
-+ ret = bm2835_mmal_init_device(dev, &dev->vdev);
-+ if (ret < 0)
-+ goto unreg_dev;
-+
-+ /* Really want to call vidioc_s_fmt_vid_cap with the default
-+ * format, but currently the APIs don't join up.
-+ */
-+ ret = mmal_setup_components(dev, &default_v4l2_format);
-+ if (ret < 0) {
-+ v4l2_err(&dev->v4l2_dev,
-+ "%s: could not setup components\n", __func__);
-+ goto unreg_dev;
-+ }
-+
-+ v4l2_info(&dev->v4l2_dev,
-+ "Broadcom 2835 MMAL video capture ver %s loaded.\n",
-+ BM2835_MMAL_VERSION);
-+
-+ gdev = dev;
-+ return 0;
-+
-+unreg_dev:
-+ v4l2_ctrl_handler_free(&dev->ctrl_handler);
-+ v4l2_device_unregister(&dev->v4l2_dev);
-+
-+free_dev:
-+ kfree(dev);
-+
-+ v4l2_err(&dev->v4l2_dev,
-+ "%s: error %d while loading driver\n",
-+ BM2835_MMAL_MODULE_NAME, ret);
-+
-+ return ret;
-+}
-+
-+static void __exit bm2835_mmal_exit(void)
-+{
-+ if (!gdev)
-+ return;
-+
-+ v4l2_info(&gdev->v4l2_dev, "unregistering %s\n",
-+ video_device_node_name(&gdev->vdev));
-+
-+ video_unregister_device(&gdev->vdev);
-+
-+ if (gdev->capture.encode_component) {
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &gdev->v4l2_dev,
-+ "mmal_exit - disconnect tunnel\n");
-+ vchiq_mmal_port_connect_tunnel(gdev->instance,
-+ gdev->capture.camera_port, NULL);
-+ vchiq_mmal_component_disable(gdev->instance,
-+ gdev->capture.encode_component);
-+ }
-+ vchiq_mmal_component_disable(gdev->instance,
-+ gdev->component[MMAL_COMPONENT_CAMERA]);
-+
-+ vchiq_mmal_component_finalise(gdev->instance,
-+ gdev->
-+ component[MMAL_COMPONENT_VIDEO_ENCODE]);
-+
-+ vchiq_mmal_component_finalise(gdev->instance,
-+ gdev->
-+ component[MMAL_COMPONENT_IMAGE_ENCODE]);
-+
-+ vchiq_mmal_component_finalise(gdev->instance,
-+ gdev->component[MMAL_COMPONENT_PREVIEW]);
-+
-+ vchiq_mmal_component_finalise(gdev->instance,
-+ gdev->component[MMAL_COMPONENT_CAMERA]);
-+
-+ vchiq_mmal_finalise(gdev->instance);
-+
-+ v4l2_ctrl_handler_free(&gdev->ctrl_handler);
-+
-+ v4l2_device_unregister(&gdev->v4l2_dev);
-+
-+ kfree(gdev);
-+}
-+
-+module_init(bm2835_mmal_init);
-+module_exit(bm2835_mmal_exit);
---- /dev/null
-+++ b/drivers/media/platform/bcm2835/bcm2835-camera.h
-@@ -0,0 +1,126 @@
-+/*
-+ * Broadcom BM2835 V4L2 driver
-+ *
-+ * Copyright © 2013 Raspberry Pi (Trading) Ltd.
-+ *
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License. See the file COPYING in the main directory of this archive
-+ * for more details.
-+ *
-+ * Authors: Vincent Sanders <vincent.sanders at collabora.co.uk>
-+ * Dave Stevenson <dsteve at broadcom.com>
-+ * Simon Mellor <simellor at broadcom.com>
-+ * Luke Diamand <luked at broadcom.com>
-+ *
-+ * core driver device
-+ */
-+
-+#define V4L2_CTRL_COUNT 28 /* number of v4l controls */
-+
-+enum {
-+ MMAL_COMPONENT_CAMERA = 0,
-+ MMAL_COMPONENT_PREVIEW,
-+ MMAL_COMPONENT_IMAGE_ENCODE,
-+ MMAL_COMPONENT_VIDEO_ENCODE,
-+ MMAL_COMPONENT_COUNT
-+};
-+
-+enum {
-+ MMAL_CAMERA_PORT_PREVIEW = 0,
-+ MMAL_CAMERA_PORT_VIDEO,
-+ MMAL_CAMERA_PORT_CAPTURE,
-+ MMAL_CAMERA_PORT_COUNT
-+};
-+
-+#define PREVIEW_LAYER 2
-+
-+extern int bcm2835_v4l2_debug;
-+
-+struct bm2835_mmal_dev {
-+ /* v4l2 devices */
-+ struct v4l2_device v4l2_dev;
-+ struct video_device vdev;
-+ struct mutex mutex;
-+
-+ /* controls */
-+ struct v4l2_ctrl_handler ctrl_handler;
-+ struct v4l2_ctrl *ctrls[V4L2_CTRL_COUNT];
-+ enum v4l2_scene_mode scene_mode;
-+ struct mmal_colourfx colourfx;
-+ int hflip;
-+ int vflip;
-+ int red_gain;
-+ int blue_gain;
-+ enum mmal_parameter_exposuremode exposure_mode_user;
-+ enum v4l2_exposure_auto_type exposure_mode_v4l2_user;
-+ /* active exposure mode may differ if selected via a scene mode */
-+ enum mmal_parameter_exposuremode exposure_mode_active;
-+ enum mmal_parameter_exposuremeteringmode metering_mode;
-+ unsigned int manual_shutter_speed;
-+ bool exp_auto_priority;
-+
-+ /* allocated mmal instance and components */
-+ struct vchiq_mmal_instance *instance;
-+ struct vchiq_mmal_component *component[MMAL_COMPONENT_COUNT];
-+ int camera_use_count;
-+
-+ struct v4l2_window overlay;
-+
-+ struct {
-+ unsigned int width; /* width */
-+ unsigned int height; /* height */
-+ unsigned int stride; /* stride */
-+ unsigned int buffersize; /* buffer size with padding */
-+ struct mmal_fmt *fmt;
-+ struct v4l2_fract timeperframe;
-+
-+ /* H264 encode bitrate */
-+ int encode_bitrate;
-+ /* H264 bitrate mode. CBR/VBR */
-+ int encode_bitrate_mode;
-+ /* H264 profile */
-+ enum v4l2_mpeg_video_h264_profile enc_profile;
-+ /* H264 level */
-+ enum v4l2_mpeg_video_h264_level enc_level;
-+ /* JPEG Q-factor */
-+ int q_factor;
-+
-+ struct vb2_queue vb_vidq;
-+
-+ /* VC start timestamp for streaming */
-+ s64 vc_start_timestamp;
-+ /* Kernel start timestamp for streaming */
-+ struct timeval kernel_start_ts;
-+
-+ struct vchiq_mmal_port *port; /* port being used for capture */
-+ /* camera port being used for capture */
-+ struct vchiq_mmal_port *camera_port;
-+ /* component being used for encode */
-+ struct vchiq_mmal_component *encode_component;
-+ /* number of frames remaining which driver should capture */
-+ unsigned int frame_count;
-+ /* last frame completion */
-+ struct completion frame_cmplt;
-+
-+ } capture;
-+
-+};
-+
-+int bm2835_mmal_init_controls(
-+ struct bm2835_mmal_dev *dev,
-+ struct v4l2_ctrl_handler *hdl);
-+
-+int bm2835_mmal_set_all_camera_controls(struct bm2835_mmal_dev *dev);
-+int set_framerate_params(struct bm2835_mmal_dev *dev);
-+
-+/* Debug helpers */
-+
-+#define v4l2_dump_pix_format(level, debug, dev, pix_fmt, desc) \
-+{ \
-+ v4l2_dbg(level, debug, dev, \
-+"%s: w %u h %u field %u pfmt 0x%x bpl %u sz_img %u colorspace 0x%x priv %u\n", \
-+ desc == NULL ? "" : desc, \
-+ (pix_fmt)->width, (pix_fmt)->height, (pix_fmt)->field, \
-+ (pix_fmt)->pixelformat, (pix_fmt)->bytesperline, \
-+ (pix_fmt)->sizeimage, (pix_fmt)->colorspace, (pix_fmt)->priv); \
-+}
---- /dev/null
-+++ b/drivers/media/platform/bcm2835/controls.c
-@@ -0,0 +1,1324 @@
-+/*
-+ * Broadcom BM2835 V4L2 driver
-+ *
-+ * Copyright © 2013 Raspberry Pi (Trading) Ltd.
-+ *
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License. See the file COPYING in the main directory of this archive
-+ * for more details.
-+ *
-+ * Authors: Vincent Sanders <vincent.sanders at collabora.co.uk>
-+ * Dave Stevenson <dsteve at broadcom.com>
-+ * Simon Mellor <simellor at broadcom.com>
-+ * Luke Diamand <luked at broadcom.com>
-+ */
-+
-+#include <linux/errno.h>
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+#include <linux/slab.h>
-+#include <media/videobuf2-vmalloc.h>
-+#include <media/v4l2-device.h>
-+#include <media/v4l2-ioctl.h>
-+#include <media/v4l2-ctrls.h>
-+#include <media/v4l2-fh.h>
-+#include <media/v4l2-event.h>
-+#include <media/v4l2-common.h>
-+
-+#include "mmal-common.h"
-+#include "mmal-vchiq.h"
-+#include "mmal-parameters.h"
-+#include "bcm2835-camera.h"
-+
-+/* The supported V4L2_CID_AUTO_EXPOSURE_BIAS values are from -4.0 to +4.0.
-+ * MMAL values are in 1/6th increments so the MMAL range is -24 to +24.
-+ * V4L2 docs say value "is expressed in terms of EV, drivers should interpret
-+ * the values as 0.001 EV units, where the value 1000 stands for +1 EV."
-+ * V4L2 is limited to a max of 32 values in a menu, so count in 1/3rds from
-+ * -4 to +4
-+ */
-+static const s64 ev_bias_qmenu[] = {
-+ -4000, -3667, -3333,
-+ -3000, -2667, -2333,
-+ -2000, -1667, -1333,
-+ -1000, -667, -333,
-+ 0, 333, 667,
-+ 1000, 1333, 1667,
-+ 2000, 2333, 2667,
-+ 3000, 3333, 3667,
-+ 4000
-+};
-+
-+/* Supported ISO values
-+ * ISOO = auto ISO
-+ */
-+static const s64 iso_qmenu[] = {
-+ 0, 100, 200, 400, 800,
-+};
-+
-+static const s64 mains_freq_qmenu[] = {
-+ V4L2_CID_POWER_LINE_FREQUENCY_DISABLED,
-+ V4L2_CID_POWER_LINE_FREQUENCY_50HZ,
-+ V4L2_CID_POWER_LINE_FREQUENCY_60HZ,
-+ V4L2_CID_POWER_LINE_FREQUENCY_AUTO
-+};
-+
-+/* Supported video encode modes */
-+static const s64 bitrate_mode_qmenu[] = {
-+ (s64)V4L2_MPEG_VIDEO_BITRATE_MODE_VBR,
-+ (s64)V4L2_MPEG_VIDEO_BITRATE_MODE_CBR,
-+};
-+
-+enum bm2835_mmal_ctrl_type {
-+ MMAL_CONTROL_TYPE_STD,
-+ MMAL_CONTROL_TYPE_STD_MENU,
-+ MMAL_CONTROL_TYPE_INT_MENU,
-+ MMAL_CONTROL_TYPE_CLUSTER, /* special cluster entry */
-+};
-+
-+struct bm2835_mmal_v4l2_ctrl;
-+
-+typedef int(bm2835_mmal_v4l2_ctrl_cb)(
-+ struct bm2835_mmal_dev *dev,
-+ struct v4l2_ctrl *ctrl,
-+ const struct bm2835_mmal_v4l2_ctrl *mmal_ctrl);
-+
-+struct bm2835_mmal_v4l2_ctrl {
-+ u32 id; /* v4l2 control identifier */
-+ enum bm2835_mmal_ctrl_type type;
-+ /* control minimum value or
-+ * mask for MMAL_CONTROL_TYPE_STD_MENU */
-+ s32 min;
-+ s32 max; /* maximum value of control */
-+ s32 def; /* default value of control */
-+ s32 step; /* step size of the control */
-+ const s64 *imenu; /* integer menu array */
-+ u32 mmal_id; /* mmal parameter id */
-+ bm2835_mmal_v4l2_ctrl_cb *setter;
-+ bool ignore_errors;
-+};
-+
-+struct v4l2_to_mmal_effects_setting {
-+ u32 v4l2_effect;
-+ u32 mmal_effect;
-+ s32 col_fx_enable;
-+ s32 col_fx_fixed_cbcr;
-+ u32 u;
-+ u32 v;
-+ u32 num_effect_params;
-+ u32 effect_params[MMAL_MAX_IMAGEFX_PARAMETERS];
-+};
-+
-+static const struct v4l2_to_mmal_effects_setting
-+ v4l2_to_mmal_effects_values[] = {
-+ { V4L2_COLORFX_NONE, MMAL_PARAM_IMAGEFX_NONE,
-+ 0, 0, 0, 0, 0, {0, 0, 0, 0, 0} },
-+ { V4L2_COLORFX_BW, MMAL_PARAM_IMAGEFX_NONE,
-+ 1, 0, 128, 128, 0, {0, 0, 0, 0, 0} },
-+ { V4L2_COLORFX_SEPIA, MMAL_PARAM_IMAGEFX_NONE,
-+ 1, 0, 87, 151, 0, {0, 0, 0, 0, 0} },
-+ { V4L2_COLORFX_NEGATIVE, MMAL_PARAM_IMAGEFX_NEGATIVE,
-+ 0, 0, 0, 0, 0, {0, 0, 0, 0, 0} },
-+ { V4L2_COLORFX_EMBOSS, MMAL_PARAM_IMAGEFX_EMBOSS,
-+ 0, 0, 0, 0, 0, {0, 0, 0, 0, 0} },
-+ { V4L2_COLORFX_SKETCH, MMAL_PARAM_IMAGEFX_SKETCH,
-+ 0, 0, 0, 0, 0, {0, 0, 0, 0, 0} },
-+ { V4L2_COLORFX_SKY_BLUE, MMAL_PARAM_IMAGEFX_PASTEL,
-+ 0, 0, 0, 0, 0, {0, 0, 0, 0, 0} },
-+ { V4L2_COLORFX_GRASS_GREEN, MMAL_PARAM_IMAGEFX_WATERCOLOUR,
-+ 0, 0, 0, 0, 0, {0, 0, 0, 0, 0} },
-+ { V4L2_COLORFX_SKIN_WHITEN, MMAL_PARAM_IMAGEFX_WASHEDOUT,
-+ 0, 0, 0, 0, 0, {0, 0, 0, 0, 0} },
-+ { V4L2_COLORFX_VIVID, MMAL_PARAM_IMAGEFX_SATURATION,
-+ 0, 0, 0, 0, 0, {0, 0, 0, 0, 0} },
-+ { V4L2_COLORFX_AQUA, MMAL_PARAM_IMAGEFX_NONE,
-+ 1, 0, 171, 121, 0, {0, 0, 0, 0, 0} },
-+ { V4L2_COLORFX_ART_FREEZE, MMAL_PARAM_IMAGEFX_HATCH,
-+ 0, 0, 0, 0, 0, {0, 0, 0, 0, 0} },
-+ { V4L2_COLORFX_SILHOUETTE, MMAL_PARAM_IMAGEFX_FILM,
-+ 0, 0, 0, 0, 0, {0, 0, 0, 0, 0} },
-+ { V4L2_COLORFX_SOLARIZATION, MMAL_PARAM_IMAGEFX_SOLARIZE,
-+ 0, 0, 0, 0, 5, {1, 128, 160, 160, 48} },
-+ { V4L2_COLORFX_ANTIQUE, MMAL_PARAM_IMAGEFX_COLOURBALANCE,
-+ 0, 0, 0, 0, 3, {108, 274, 238, 0, 0} },
-+ { V4L2_COLORFX_SET_CBCR, MMAL_PARAM_IMAGEFX_NONE,
-+ 1, 1, 0, 0, 0, {0, 0, 0, 0, 0} }
-+};
-+
-+struct v4l2_mmal_scene_config {
-+ enum v4l2_scene_mode v4l2_scene;
-+ enum mmal_parameter_exposuremode exposure_mode;
-+ enum mmal_parameter_exposuremeteringmode metering_mode;
-+};
-+
-+static const struct v4l2_mmal_scene_config scene_configs[] = {
-+ /* V4L2_SCENE_MODE_NONE automatically added */
-+ {
-+ V4L2_SCENE_MODE_NIGHT,
-+ MMAL_PARAM_EXPOSUREMODE_NIGHT,
-+ MMAL_PARAM_EXPOSUREMETERINGMODE_AVERAGE
-+ },
-+ {
-+ V4L2_SCENE_MODE_SPORTS,
-+ MMAL_PARAM_EXPOSUREMODE_SPORTS,
-+ MMAL_PARAM_EXPOSUREMETERINGMODE_AVERAGE
-+ },
-+};
-+
-+/* control handlers*/
-+
-+static int ctrl_set_rational(struct bm2835_mmal_dev *dev,
-+ struct v4l2_ctrl *ctrl,
-+ const struct bm2835_mmal_v4l2_ctrl *mmal_ctrl)
-+{
-+ struct mmal_parameter_rational rational_value;
-+ struct vchiq_mmal_port *control;
-+
-+ control = &dev->component[MMAL_COMPONENT_CAMERA]->control;
-+
-+ rational_value.num = ctrl->val;
-+ rational_value.den = 100;
-+
-+ return vchiq_mmal_port_parameter_set(dev->instance, control,
-+ mmal_ctrl->mmal_id,
-+ &rational_value,
-+ sizeof(rational_value));
-+}
-+
-+static int ctrl_set_value(struct bm2835_mmal_dev *dev,
-+ struct v4l2_ctrl *ctrl,
-+ const struct bm2835_mmal_v4l2_ctrl *mmal_ctrl)
-+{
-+ u32 u32_value;
-+ struct vchiq_mmal_port *control;
-+
-+ control = &dev->component[MMAL_COMPONENT_CAMERA]->control;
-+
-+ u32_value = ctrl->val;
-+
-+ return vchiq_mmal_port_parameter_set(dev->instance, control,
-+ mmal_ctrl->mmal_id,
-+ &u32_value, sizeof(u32_value));
-+}
-+
-+static int ctrl_set_value_menu(struct bm2835_mmal_dev *dev,
-+ struct v4l2_ctrl *ctrl,
-+ const struct bm2835_mmal_v4l2_ctrl *mmal_ctrl)
-+{
-+ u32 u32_value;
-+ struct vchiq_mmal_port *control;
-+
-+ if (ctrl->val > mmal_ctrl->max || ctrl->val < mmal_ctrl->min)
-+ return 1;
-+
-+ control = &dev->component[MMAL_COMPONENT_CAMERA]->control;
-+
-+ u32_value = mmal_ctrl->imenu[ctrl->val];
-+
-+ return vchiq_mmal_port_parameter_set(dev->instance, control,
-+ mmal_ctrl->mmal_id,
-+ &u32_value, sizeof(u32_value));
-+}
-+
-+static int ctrl_set_value_ev(struct bm2835_mmal_dev *dev,
-+ struct v4l2_ctrl *ctrl,
-+ const struct bm2835_mmal_v4l2_ctrl *mmal_ctrl)
-+{
-+ s32 s32_value;
-+ struct vchiq_mmal_port *control;
-+
-+ control = &dev->component[MMAL_COMPONENT_CAMERA]->control;
-+
-+ s32_value = (ctrl->val-12)*2; /* Convert from index to 1/6ths */
-+
-+ return vchiq_mmal_port_parameter_set(dev->instance, control,
-+ mmal_ctrl->mmal_id,
-+ &s32_value, sizeof(s32_value));
-+}
-+
-+static int ctrl_set_rotate(struct bm2835_mmal_dev *dev,
-+ struct v4l2_ctrl *ctrl,
-+ const struct bm2835_mmal_v4l2_ctrl *mmal_ctrl)
-+{
-+ int ret;
-+ u32 u32_value;
-+ struct vchiq_mmal_component *camera;
-+
-+ camera = dev->component[MMAL_COMPONENT_CAMERA];
-+
-+ u32_value = ((ctrl->val % 360) / 90) * 90;
-+
-+ ret = vchiq_mmal_port_parameter_set(dev->instance, &camera->output[0],
-+ mmal_ctrl->mmal_id,
-+ &u32_value, sizeof(u32_value));
-+ if (ret < 0)
-+ return ret;
-+
-+ ret = vchiq_mmal_port_parameter_set(dev->instance, &camera->output[1],
-+ mmal_ctrl->mmal_id,
-+ &u32_value, sizeof(u32_value));
-+ if (ret < 0)
-+ return ret;
-+
-+ ret = vchiq_mmal_port_parameter_set(dev->instance, &camera->output[2],
-+ mmal_ctrl->mmal_id,
-+ &u32_value, sizeof(u32_value));
-+
-+ return ret;
-+}
-+
-+static int ctrl_set_flip(struct bm2835_mmal_dev *dev,
-+ struct v4l2_ctrl *ctrl,
-+ const struct bm2835_mmal_v4l2_ctrl *mmal_ctrl)
-+{
-+ int ret;
-+ u32 u32_value;
-+ struct vchiq_mmal_component *camera;
-+
-+ if (ctrl->id == V4L2_CID_HFLIP)
-+ dev->hflip = ctrl->val;
-+ else
-+ dev->vflip = ctrl->val;
-+
-+ camera = dev->component[MMAL_COMPONENT_CAMERA];
-+
-+ if (dev->hflip && dev->vflip)
-+ u32_value = MMAL_PARAM_MIRROR_BOTH;
-+ else if (dev->hflip)
-+ u32_value = MMAL_PARAM_MIRROR_HORIZONTAL;
-+ else if (dev->vflip)
-+ u32_value = MMAL_PARAM_MIRROR_VERTICAL;
-+ else
-+ u32_value = MMAL_PARAM_MIRROR_NONE;
-+
-+ ret = vchiq_mmal_port_parameter_set(dev->instance, &camera->output[0],
-+ mmal_ctrl->mmal_id,
-+ &u32_value, sizeof(u32_value));
-+ if (ret < 0)
-+ return ret;
-+
-+ ret = vchiq_mmal_port_parameter_set(dev->instance, &camera->output[1],
-+ mmal_ctrl->mmal_id,
-+ &u32_value, sizeof(u32_value));
-+ if (ret < 0)
-+ return ret;
-+
-+ ret = vchiq_mmal_port_parameter_set(dev->instance, &camera->output[2],
-+ mmal_ctrl->mmal_id,
-+ &u32_value, sizeof(u32_value));
-+
-+ return ret;
-+
-+}
-+
-+static int ctrl_set_exposure(struct bm2835_mmal_dev *dev,
-+ struct v4l2_ctrl *ctrl,
-+ const struct bm2835_mmal_v4l2_ctrl *mmal_ctrl)
-+{
-+ enum mmal_parameter_exposuremode exp_mode = dev->exposure_mode_user;
-+ u32 shutter_speed = 0;
-+ struct vchiq_mmal_port *control;
-+ int ret = 0;
-+
-+ control = &dev->component[MMAL_COMPONENT_CAMERA]->control;
-+
-+ if (mmal_ctrl->mmal_id == MMAL_PARAMETER_SHUTTER_SPEED) {
-+ /* V4L2 is in 100usec increments.
-+ * MMAL is 1usec.
-+ */
-+ dev->manual_shutter_speed = ctrl->val * 100;
-+ } else if (mmal_ctrl->mmal_id == MMAL_PARAMETER_EXPOSURE_MODE) {
-+ switch (ctrl->val) {
-+ case V4L2_EXPOSURE_AUTO:
-+ exp_mode = MMAL_PARAM_EXPOSUREMODE_AUTO;
-+ break;
-+
-+ case V4L2_EXPOSURE_MANUAL:
-+ exp_mode = MMAL_PARAM_EXPOSUREMODE_OFF;
-+ break;
-+ }
-+ dev->exposure_mode_user = exp_mode;
-+ dev->exposure_mode_v4l2_user = ctrl->val;
-+ } else if (mmal_ctrl->id == V4L2_CID_EXPOSURE_AUTO_PRIORITY) {
-+ dev->exp_auto_priority = ctrl->val;
-+ }
-+
-+ if (dev->scene_mode == V4L2_SCENE_MODE_NONE) {
-+ if (exp_mode == MMAL_PARAM_EXPOSUREMODE_OFF)
-+ shutter_speed = dev->manual_shutter_speed;
-+
-+ ret = vchiq_mmal_port_parameter_set(dev->instance,
-+ control,
-+ MMAL_PARAMETER_SHUTTER_SPEED,
-+ &shutter_speed,
-+ sizeof(shutter_speed));
-+ ret += vchiq_mmal_port_parameter_set(dev->instance,
-+ control,
-+ MMAL_PARAMETER_EXPOSURE_MODE,
-+ &exp_mode,
-+ sizeof(u32));
-+ dev->exposure_mode_active = exp_mode;
-+ }
-+ /* exposure_dynamic_framerate (V4L2_CID_EXPOSURE_AUTO_PRIORITY) should
-+ * always apply irrespective of scene mode.
-+ */
-+ ret += set_framerate_params(dev);
-+
-+ return ret;
-+}
-+
-+static int ctrl_set_metering_mode(struct bm2835_mmal_dev *dev,
-+ struct v4l2_ctrl *ctrl,
-+ const struct bm2835_mmal_v4l2_ctrl *mmal_ctrl)
-+{
-+ switch (ctrl->val) {
-+ case V4L2_EXPOSURE_METERING_AVERAGE:
-+ dev->metering_mode = MMAL_PARAM_EXPOSUREMETERINGMODE_AVERAGE;
-+ break;
-+
-+ case V4L2_EXPOSURE_METERING_CENTER_WEIGHTED:
-+ dev->metering_mode = MMAL_PARAM_EXPOSUREMETERINGMODE_BACKLIT;
-+ break;
-+
-+ case V4L2_EXPOSURE_METERING_SPOT:
-+ dev->metering_mode = MMAL_PARAM_EXPOSUREMETERINGMODE_SPOT;
-+ break;
-+
-+ /* todo matrix weighting not added to Linux API till 3.9
-+ case V4L2_EXPOSURE_METERING_MATRIX:
-+ dev->metering_mode = MMAL_PARAM_EXPOSUREMETERINGMODE_MATRIX;
-+ break;
-+ */
-+
-+ }
-+
-+ if (dev->scene_mode == V4L2_SCENE_MODE_NONE) {
-+ struct vchiq_mmal_port *control;
-+ u32 u32_value = dev->metering_mode;
-+
-+ control = &dev->component[MMAL_COMPONENT_CAMERA]->control;
-+
-+ return vchiq_mmal_port_parameter_set(dev->instance, control,
-+ mmal_ctrl->mmal_id,
-+ &u32_value, sizeof(u32_value));
-+ } else
-+ return 0;
-+}
-+
-+static int ctrl_set_flicker_avoidance(struct bm2835_mmal_dev *dev,
-+ struct v4l2_ctrl *ctrl,
-+ const struct bm2835_mmal_v4l2_ctrl *mmal_ctrl)
-+{
-+ u32 u32_value;
-+ struct vchiq_mmal_port *control;
-+
-+ control = &dev->component[MMAL_COMPONENT_CAMERA]->control;
-+
-+ switch (ctrl->val) {
-+ case V4L2_CID_POWER_LINE_FREQUENCY_DISABLED:
-+ u32_value = MMAL_PARAM_FLICKERAVOID_OFF;
-+ break;
-+ case V4L2_CID_POWER_LINE_FREQUENCY_50HZ:
-+ u32_value = MMAL_PARAM_FLICKERAVOID_50HZ;
-+ break;
-+ case V4L2_CID_POWER_LINE_FREQUENCY_60HZ:
-+ u32_value = MMAL_PARAM_FLICKERAVOID_60HZ;
-+ break;
-+ case V4L2_CID_POWER_LINE_FREQUENCY_AUTO:
-+ u32_value = MMAL_PARAM_FLICKERAVOID_AUTO;
-+ break;
-+ }
-+
-+ return vchiq_mmal_port_parameter_set(dev->instance, control,
-+ mmal_ctrl->mmal_id,
-+ &u32_value, sizeof(u32_value));
-+}
-+
-+static int ctrl_set_awb_mode(struct bm2835_mmal_dev *dev,
-+ struct v4l2_ctrl *ctrl,
-+ const struct bm2835_mmal_v4l2_ctrl *mmal_ctrl)
-+{
-+ u32 u32_value;
-+ struct vchiq_mmal_port *control;
-+
-+ control = &dev->component[MMAL_COMPONENT_CAMERA]->control;
-+
-+ switch (ctrl->val) {
-+ case V4L2_WHITE_BALANCE_MANUAL:
-+ u32_value = MMAL_PARAM_AWBMODE_OFF;
-+ break;
-+
-+ case V4L2_WHITE_BALANCE_AUTO:
-+ u32_value = MMAL_PARAM_AWBMODE_AUTO;
-+ break;
-+
-+ case V4L2_WHITE_BALANCE_INCANDESCENT:
-+ u32_value = MMAL_PARAM_AWBMODE_INCANDESCENT;
-+ break;
-+
-+ case V4L2_WHITE_BALANCE_FLUORESCENT:
-+ u32_value = MMAL_PARAM_AWBMODE_FLUORESCENT;
-+ break;
-+
-+ case V4L2_WHITE_BALANCE_FLUORESCENT_H:
-+ u32_value = MMAL_PARAM_AWBMODE_TUNGSTEN;
-+ break;
-+
-+ case V4L2_WHITE_BALANCE_HORIZON:
-+ u32_value = MMAL_PARAM_AWBMODE_HORIZON;
-+ break;
-+
-+ case V4L2_WHITE_BALANCE_DAYLIGHT:
-+ u32_value = MMAL_PARAM_AWBMODE_SUNLIGHT;
-+ break;
-+
-+ case V4L2_WHITE_BALANCE_FLASH:
-+ u32_value = MMAL_PARAM_AWBMODE_FLASH;
-+ break;
-+
-+ case V4L2_WHITE_BALANCE_CLOUDY:
-+ u32_value = MMAL_PARAM_AWBMODE_CLOUDY;
-+ break;
-+
-+ case V4L2_WHITE_BALANCE_SHADE:
-+ u32_value = MMAL_PARAM_AWBMODE_SHADE;
-+ break;
-+
-+ }
-+
-+ return vchiq_mmal_port_parameter_set(dev->instance, control,
-+ mmal_ctrl->mmal_id,
-+ &u32_value, sizeof(u32_value));
-+}
-+
-+static int ctrl_set_awb_gains(struct bm2835_mmal_dev *dev,
-+ struct v4l2_ctrl *ctrl,
-+ const struct bm2835_mmal_v4l2_ctrl *mmal_ctrl)
-+{
-+ struct vchiq_mmal_port *control;
-+ struct mmal_parameter_awbgains gains;
-+
-+ control = &dev->component[MMAL_COMPONENT_CAMERA]->control;
-+
-+ if (ctrl->id == V4L2_CID_RED_BALANCE)
-+ dev->red_gain = ctrl->val;
-+ else if (ctrl->id == V4L2_CID_BLUE_BALANCE)
-+ dev->blue_gain = ctrl->val;
-+
-+ gains.r_gain.num = dev->red_gain;
-+ gains.b_gain.num = dev->blue_gain;
-+ gains.r_gain.den = gains.b_gain.den = 1000;
-+
-+ return vchiq_mmal_port_parameter_set(dev->instance, control,
-+ mmal_ctrl->mmal_id,
-+ &gains, sizeof(gains));
-+}
-+
-+static int ctrl_set_image_effect(struct bm2835_mmal_dev *dev,
-+ struct v4l2_ctrl *ctrl,
-+ const struct bm2835_mmal_v4l2_ctrl *mmal_ctrl)
-+{
-+ int ret = -EINVAL;
-+ int i, j;
-+ struct vchiq_mmal_port *control;
-+ struct mmal_parameter_imagefx_parameters imagefx;
-+
-+ for (i = 0; i < ARRAY_SIZE(v4l2_to_mmal_effects_values); i++) {
-+ if (ctrl->val == v4l2_to_mmal_effects_values[i].v4l2_effect) {
-+
-+ imagefx.effect =
-+ v4l2_to_mmal_effects_values[i].mmal_effect;
-+ imagefx.num_effect_params =
-+ v4l2_to_mmal_effects_values[i].num_effect_params;
-+
-+ if (imagefx.num_effect_params > MMAL_MAX_IMAGEFX_PARAMETERS)
-+ imagefx.num_effect_params = MMAL_MAX_IMAGEFX_PARAMETERS;
-+
-+ for (j = 0; j < imagefx.num_effect_params; j++)
-+ imagefx.effect_parameter[j] =
-+ v4l2_to_mmal_effects_values[i].effect_params[j];
-+
-+ dev->colourfx.enable =
-+ v4l2_to_mmal_effects_values[i].col_fx_enable;
-+ if (!v4l2_to_mmal_effects_values[i].col_fx_fixed_cbcr) {
-+ dev->colourfx.u =
-+ v4l2_to_mmal_effects_values[i].u;
-+ dev->colourfx.v =
-+ v4l2_to_mmal_effects_values[i].v;
-+ }
-+
-+ control = &dev->component[MMAL_COMPONENT_CAMERA]->control;
-+
-+ ret = vchiq_mmal_port_parameter_set(
-+ dev->instance, control,
-+ MMAL_PARAMETER_IMAGE_EFFECT_PARAMETERS,
-+ &imagefx, sizeof(imagefx));
-+ if (ret)
-+ goto exit;
-+
-+ ret = vchiq_mmal_port_parameter_set(
-+ dev->instance, control,
-+ MMAL_PARAMETER_COLOUR_EFFECT,
-+ &dev->colourfx, sizeof(dev->colourfx));
-+ }
-+ }
-+
-+exit:
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "mmal_ctrl:%p ctrl id:0x%x ctrl val:%d imagefx:0x%x color_effect:%s u:%d v:%d ret %d(%d)\n",
-+ mmal_ctrl, ctrl->id, ctrl->val, imagefx.effect,
-+ dev->colourfx.enable ? "true" : "false",
-+ dev->colourfx.u, dev->colourfx.v,
-+ ret, (ret == 0 ? 0 : -EINVAL));
-+ return (ret == 0 ? 0 : EINVAL);
-+}
-+
-+static int ctrl_set_colfx(struct bm2835_mmal_dev *dev,
-+ struct v4l2_ctrl *ctrl,
-+ const struct bm2835_mmal_v4l2_ctrl *mmal_ctrl)
-+{
-+ int ret = -EINVAL;
-+ struct vchiq_mmal_port *control;
-+
-+ control = &dev->component[MMAL_COMPONENT_CAMERA]->control;
-+
-+ dev->colourfx.enable = (ctrl->val & 0xff00) >> 8;
-+ dev->colourfx.enable = ctrl->val & 0xff;
-+
-+ ret = vchiq_mmal_port_parameter_set(dev->instance, control,
-+ MMAL_PARAMETER_COLOUR_EFFECT,
-+ &dev->colourfx, sizeof(dev->colourfx));
-+
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "%s: After: mmal_ctrl:%p ctrl id:0x%x ctrl val:%d ret %d(%d)\n",
-+ __func__, mmal_ctrl, ctrl->id, ctrl->val, ret,
-+ (ret == 0 ? 0 : -EINVAL));
-+ return (ret == 0 ? 0 : EINVAL);
-+}
-+
-+static int ctrl_set_bitrate(struct bm2835_mmal_dev *dev,
-+ struct v4l2_ctrl *ctrl,
-+ const struct bm2835_mmal_v4l2_ctrl *mmal_ctrl)
-+{
-+ int ret;
-+ struct vchiq_mmal_port *encoder_out;
-+
-+ dev->capture.encode_bitrate = ctrl->val;
-+
-+ encoder_out = &dev->component[MMAL_COMPONENT_VIDEO_ENCODE]->output[0];
-+
-+ ret = vchiq_mmal_port_parameter_set(dev->instance, encoder_out,
-+ mmal_ctrl->mmal_id,
-+ &ctrl->val, sizeof(ctrl->val));
-+ ret = 0;
-+ return ret;
-+}
-+
-+static int ctrl_set_bitrate_mode(struct bm2835_mmal_dev *dev,
-+ struct v4l2_ctrl *ctrl,
-+ const struct bm2835_mmal_v4l2_ctrl *mmal_ctrl)
-+{
-+ u32 bitrate_mode;
-+ struct vchiq_mmal_port *encoder_out;
-+
-+ encoder_out = &dev->component[MMAL_COMPONENT_VIDEO_ENCODE]->output[0];
-+
-+ dev->capture.encode_bitrate_mode = ctrl->val;
-+ switch (ctrl->val) {
-+ default:
-+ case V4L2_MPEG_VIDEO_BITRATE_MODE_VBR:
-+ bitrate_mode = MMAL_VIDEO_RATECONTROL_VARIABLE;
-+ break;
-+ case V4L2_MPEG_VIDEO_BITRATE_MODE_CBR:
-+ bitrate_mode = MMAL_VIDEO_RATECONTROL_CONSTANT;
-+ break;
-+ }
-+
-+ vchiq_mmal_port_parameter_set(dev->instance, encoder_out,
-+ mmal_ctrl->mmal_id,
-+ &bitrate_mode,
-+ sizeof(bitrate_mode));
-+ return 0;
-+}
-+
-+static int ctrl_set_image_encode_output(struct bm2835_mmal_dev *dev,
-+ struct v4l2_ctrl *ctrl,
-+ const struct bm2835_mmal_v4l2_ctrl *mmal_ctrl)
-+{
-+ u32 u32_value;
-+ struct vchiq_mmal_port *jpeg_out;
-+
-+ jpeg_out = &dev->component[MMAL_COMPONENT_IMAGE_ENCODE]->output[0];
-+
-+ u32_value = ctrl->val;
-+
-+ return vchiq_mmal_port_parameter_set(dev->instance, jpeg_out,
-+ mmal_ctrl->mmal_id,
-+ &u32_value, sizeof(u32_value));
-+}
-+
-+static int ctrl_set_video_encode_param_output(struct bm2835_mmal_dev *dev,
-+ struct v4l2_ctrl *ctrl,
-+ const struct bm2835_mmal_v4l2_ctrl *mmal_ctrl)
-+{
-+ u32 u32_value;
-+ struct vchiq_mmal_port *vid_enc_ctl;
-+
-+ vid_enc_ctl = &dev->component[MMAL_COMPONENT_VIDEO_ENCODE]->output[0];
-+
-+ u32_value = ctrl->val;
-+
-+ return vchiq_mmal_port_parameter_set(dev->instance, vid_enc_ctl,
-+ mmal_ctrl->mmal_id,
-+ &u32_value, sizeof(u32_value));
-+}
-+
-+static int ctrl_set_video_encode_profile_level(struct bm2835_mmal_dev *dev,
-+ struct v4l2_ctrl *ctrl,
-+ const struct bm2835_mmal_v4l2_ctrl *mmal_ctrl)
-+{
-+ struct mmal_parameter_video_profile param;
-+ int ret = 0;
-+
-+ if (ctrl->id == V4L2_CID_MPEG_VIDEO_H264_PROFILE) {
-+ switch (ctrl->val) {
-+ case V4L2_MPEG_VIDEO_H264_PROFILE_BASELINE:
-+ case V4L2_MPEG_VIDEO_H264_PROFILE_CONSTRAINED_BASELINE:
-+ case V4L2_MPEG_VIDEO_H264_PROFILE_MAIN:
-+ case V4L2_MPEG_VIDEO_H264_PROFILE_HIGH:
-+ dev->capture.enc_profile = ctrl->val;
-+ break;
-+ default:
-+ ret = -EINVAL;
-+ break;
-+ }
-+ } else if (ctrl->id == V4L2_CID_MPEG_VIDEO_H264_LEVEL) {
-+ switch (ctrl->val) {
-+ case V4L2_MPEG_VIDEO_H264_LEVEL_1_0:
-+ case V4L2_MPEG_VIDEO_H264_LEVEL_1B:
-+ case V4L2_MPEG_VIDEO_H264_LEVEL_1_1:
-+ case V4L2_MPEG_VIDEO_H264_LEVEL_1_2:
-+ case V4L2_MPEG_VIDEO_H264_LEVEL_1_3:
-+ case V4L2_MPEG_VIDEO_H264_LEVEL_2_0:
-+ case V4L2_MPEG_VIDEO_H264_LEVEL_2_1:
-+ case V4L2_MPEG_VIDEO_H264_LEVEL_2_2:
-+ case V4L2_MPEG_VIDEO_H264_LEVEL_3_0:
-+ case V4L2_MPEG_VIDEO_H264_LEVEL_3_1:
-+ case V4L2_MPEG_VIDEO_H264_LEVEL_3_2:
-+ case V4L2_MPEG_VIDEO_H264_LEVEL_4_0:
-+ dev->capture.enc_level = ctrl->val;
-+ break;
-+ default:
-+ ret = -EINVAL;
-+ break;
-+ }
-+ }
-+
-+ if (!ret) {
-+ switch (dev->capture.enc_profile) {
-+ case V4L2_MPEG_VIDEO_H264_PROFILE_BASELINE:
-+ param.profile = MMAL_VIDEO_PROFILE_H264_BASELINE;
-+ break;
-+ case V4L2_MPEG_VIDEO_H264_PROFILE_CONSTRAINED_BASELINE:
-+ param.profile =
-+ MMAL_VIDEO_PROFILE_H264_CONSTRAINED_BASELINE;
-+ break;
-+ case V4L2_MPEG_VIDEO_H264_PROFILE_MAIN:
-+ param.profile = MMAL_VIDEO_PROFILE_H264_MAIN;
-+ break;
-+ case V4L2_MPEG_VIDEO_H264_PROFILE_HIGH:
-+ param.profile = MMAL_VIDEO_PROFILE_H264_HIGH;
-+ break;
-+ default:
-+ /* Should never get here */
-+ break;
-+ }
-+
-+ switch (dev->capture.enc_level) {
-+ case V4L2_MPEG_VIDEO_H264_LEVEL_1_0:
-+ param.level = MMAL_VIDEO_LEVEL_H264_1;
-+ break;
-+ case V4L2_MPEG_VIDEO_H264_LEVEL_1B:
-+ param.level = MMAL_VIDEO_LEVEL_H264_1b;
-+ break;
-+ case V4L2_MPEG_VIDEO_H264_LEVEL_1_1:
-+ param.level = MMAL_VIDEO_LEVEL_H264_11;
-+ break;
-+ case V4L2_MPEG_VIDEO_H264_LEVEL_1_2:
-+ param.level = MMAL_VIDEO_LEVEL_H264_12;
-+ break;
-+ case V4L2_MPEG_VIDEO_H264_LEVEL_1_3:
-+ param.level = MMAL_VIDEO_LEVEL_H264_13;
-+ break;
-+ case V4L2_MPEG_VIDEO_H264_LEVEL_2_0:
-+ param.level = MMAL_VIDEO_LEVEL_H264_2;
-+ break;
-+ case V4L2_MPEG_VIDEO_H264_LEVEL_2_1:
-+ param.level = MMAL_VIDEO_LEVEL_H264_21;
-+ break;
-+ case V4L2_MPEG_VIDEO_H264_LEVEL_2_2:
-+ param.level = MMAL_VIDEO_LEVEL_H264_22;
-+ break;
-+ case V4L2_MPEG_VIDEO_H264_LEVEL_3_0:
-+ param.level = MMAL_VIDEO_LEVEL_H264_3;
-+ break;
-+ case V4L2_MPEG_VIDEO_H264_LEVEL_3_1:
-+ param.level = MMAL_VIDEO_LEVEL_H264_31;
-+ break;
-+ case V4L2_MPEG_VIDEO_H264_LEVEL_3_2:
-+ param.level = MMAL_VIDEO_LEVEL_H264_32;
-+ break;
-+ case V4L2_MPEG_VIDEO_H264_LEVEL_4_0:
-+ param.level = MMAL_VIDEO_LEVEL_H264_4;
-+ break;
-+ default:
-+ /* Should never get here */
-+ break;
-+ }
-+
-+ ret = vchiq_mmal_port_parameter_set(dev->instance,
-+ &dev->component[MMAL_COMPONENT_VIDEO_ENCODE]->output[0],
-+ mmal_ctrl->mmal_id,
-+ ¶m, sizeof(param));
-+ }
-+ return ret;
-+}
-+
-+static int ctrl_set_scene_mode(struct bm2835_mmal_dev *dev,
-+ struct v4l2_ctrl *ctrl,
-+ const struct bm2835_mmal_v4l2_ctrl *mmal_ctrl)
-+{
-+ int ret = 0;
-+ int shutter_speed;
-+ struct vchiq_mmal_port *control;
-+
-+ v4l2_dbg(0, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "scene mode selected %d, was %d\n", ctrl->val,
-+ dev->scene_mode);
-+ control = &dev->component[MMAL_COMPONENT_CAMERA]->control;
-+
-+ if (ctrl->val == dev->scene_mode)
-+ return 0;
-+
-+ if (ctrl->val == V4L2_SCENE_MODE_NONE) {
-+ /* Restore all user selections */
-+ dev->scene_mode = V4L2_SCENE_MODE_NONE;
-+
-+ if (dev->exposure_mode_user == MMAL_PARAM_EXPOSUREMODE_OFF)
-+ shutter_speed = dev->manual_shutter_speed;
-+ else
-+ shutter_speed = 0;
-+
-+ v4l2_dbg(0, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "%s: scene mode none: shut_speed %d, exp_mode %d, metering %d\n",
-+ __func__, shutter_speed, dev->exposure_mode_user,
-+ dev->metering_mode);
-+ ret = vchiq_mmal_port_parameter_set(dev->instance,
-+ control,
-+ MMAL_PARAMETER_SHUTTER_SPEED,
-+ &shutter_speed,
-+ sizeof(shutter_speed));
-+ ret += vchiq_mmal_port_parameter_set(dev->instance,
-+ control,
-+ MMAL_PARAMETER_EXPOSURE_MODE,
-+ &dev->exposure_mode_user,
-+ sizeof(u32));
-+ dev->exposure_mode_active = dev->exposure_mode_user;
-+ ret += vchiq_mmal_port_parameter_set(dev->instance,
-+ control,
-+ MMAL_PARAMETER_EXP_METERING_MODE,
-+ &dev->metering_mode,
-+ sizeof(u32));
-+ ret += set_framerate_params(dev);
-+ } else {
-+ /* Set up scene mode */
-+ int i;
-+ const struct v4l2_mmal_scene_config *scene = NULL;
-+ int shutter_speed;
-+ enum mmal_parameter_exposuremode exposure_mode;
-+ enum mmal_parameter_exposuremeteringmode metering_mode;
-+
-+ for (i = 0; i < ARRAY_SIZE(scene_configs); i++) {
-+ if (scene_configs[i].v4l2_scene ==
-+ ctrl->val) {
-+ scene = &scene_configs[i];
-+ break;
-+ }
-+ }
-+ if (!scene)
-+ return -EINVAL;
-+ if (i >= ARRAY_SIZE(scene_configs))
-+ return -EINVAL;
-+
-+ /* Set all the values */
-+ dev->scene_mode = ctrl->val;
-+
-+ if (scene->exposure_mode == MMAL_PARAM_EXPOSUREMODE_OFF)
-+ shutter_speed = dev->manual_shutter_speed;
-+ else
-+ shutter_speed = 0;
-+ exposure_mode = scene->exposure_mode;
-+ metering_mode = scene->metering_mode;
-+
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "%s: scene mode none: shut_speed %d, exp_mode %d, metering %d\n",
-+ __func__, shutter_speed, exposure_mode, metering_mode);
-+
-+ ret = vchiq_mmal_port_parameter_set(dev->instance, control,
-+ MMAL_PARAMETER_SHUTTER_SPEED,
-+ &shutter_speed,
-+ sizeof(shutter_speed));
-+ ret += vchiq_mmal_port_parameter_set(dev->instance,
-+ control,
-+ MMAL_PARAMETER_EXPOSURE_MODE,
-+ &exposure_mode,
-+ sizeof(u32));
-+ dev->exposure_mode_active = exposure_mode;
-+ ret += vchiq_mmal_port_parameter_set(dev->instance, control,
-+ MMAL_PARAMETER_EXPOSURE_MODE,
-+ &exposure_mode,
-+ sizeof(u32));
-+ ret += vchiq_mmal_port_parameter_set(dev->instance, control,
-+ MMAL_PARAMETER_EXP_METERING_MODE,
-+ &metering_mode,
-+ sizeof(u32));
-+ ret += set_framerate_params(dev);
-+ }
-+ if (ret) {
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "%s: Setting scene to %d, ret=%d\n",
-+ __func__, ctrl->val, ret);
-+ ret = -EINVAL;
-+ }
-+ return 0;
-+}
-+
-+static int bm2835_mmal_s_ctrl(struct v4l2_ctrl *ctrl)
-+{
-+ struct bm2835_mmal_dev *dev =
-+ container_of(ctrl->handler, struct bm2835_mmal_dev,
-+ ctrl_handler);
-+ const struct bm2835_mmal_v4l2_ctrl *mmal_ctrl = ctrl->priv;
-+ int ret;
-+
-+ if ((mmal_ctrl == NULL) ||
-+ (mmal_ctrl->id != ctrl->id) ||
-+ (mmal_ctrl->setter == NULL)) {
-+ pr_warn("mmal_ctrl:%p ctrl id:%d\n", mmal_ctrl, ctrl->id);
-+ return -EINVAL;
-+ }
-+
-+ ret = mmal_ctrl->setter(dev, ctrl, mmal_ctrl);
-+ if (ret)
-+ pr_warn("ctrl id:%d/MMAL param %08X- returned ret %d\n",
-+ ctrl->id, mmal_ctrl->mmal_id, ret);
-+ if (mmal_ctrl->ignore_errors)
-+ ret = 0;
-+ return ret;
-+}
-+
-+static const struct v4l2_ctrl_ops bm2835_mmal_ctrl_ops = {
-+ .s_ctrl = bm2835_mmal_s_ctrl,
-+};
-+
-+
-+
-+static const struct bm2835_mmal_v4l2_ctrl v4l2_ctrls[V4L2_CTRL_COUNT] = {
-+ {
-+ V4L2_CID_SATURATION, MMAL_CONTROL_TYPE_STD,
-+ -100, 100, 0, 1, NULL,
-+ MMAL_PARAMETER_SATURATION,
-+ &ctrl_set_rational,
-+ false
-+ },
-+ {
-+ V4L2_CID_SHARPNESS, MMAL_CONTROL_TYPE_STD,
-+ -100, 100, 0, 1, NULL,
-+ MMAL_PARAMETER_SHARPNESS,
-+ &ctrl_set_rational,
-+ false
-+ },
-+ {
-+ V4L2_CID_CONTRAST, MMAL_CONTROL_TYPE_STD,
-+ -100, 100, 0, 1, NULL,
-+ MMAL_PARAMETER_CONTRAST,
-+ &ctrl_set_rational,
-+ false
-+ },
-+ {
-+ V4L2_CID_BRIGHTNESS, MMAL_CONTROL_TYPE_STD,
-+ 0, 100, 50, 1, NULL,
-+ MMAL_PARAMETER_BRIGHTNESS,
-+ &ctrl_set_rational,
-+ false
-+ },
-+ {
-+ V4L2_CID_ISO_SENSITIVITY, MMAL_CONTROL_TYPE_INT_MENU,
-+ 0, ARRAY_SIZE(iso_qmenu) - 1, 0, 1, iso_qmenu,
-+ MMAL_PARAMETER_ISO,
-+ &ctrl_set_value_menu,
-+ false
-+ },
-+ {
-+ V4L2_CID_IMAGE_STABILIZATION, MMAL_CONTROL_TYPE_STD,
-+ 0, 1, 0, 1, NULL,
-+ MMAL_PARAMETER_VIDEO_STABILISATION,
-+ &ctrl_set_value,
-+ false
-+ },
-+/* {
-+ 0, MMAL_CONTROL_TYPE_CLUSTER, 3, 1, 0, NULL, 0, NULL
-+ }, */
-+ {
-+ V4L2_CID_EXPOSURE_AUTO, MMAL_CONTROL_TYPE_STD_MENU,
-+ ~0x03, 3, V4L2_EXPOSURE_AUTO, 0, NULL,
-+ MMAL_PARAMETER_EXPOSURE_MODE,
-+ &ctrl_set_exposure,
-+ false
-+ },
-+/* todo this needs mixing in with set exposure
-+ {
-+ V4L2_CID_SCENE_MODE, MMAL_CONTROL_TYPE_STD_MENU,
-+ },
-+ */
-+ {
-+ V4L2_CID_EXPOSURE_ABSOLUTE, MMAL_CONTROL_TYPE_STD,
-+ /* Units of 100usecs */
-+ 1, 1*1000*10, 100*10, 1, NULL,
-+ MMAL_PARAMETER_SHUTTER_SPEED,
-+ &ctrl_set_exposure,
-+ false
-+ },
-+ {
-+ V4L2_CID_AUTO_EXPOSURE_BIAS, MMAL_CONTROL_TYPE_INT_MENU,
-+ 0, ARRAY_SIZE(ev_bias_qmenu) - 1,
-+ (ARRAY_SIZE(ev_bias_qmenu)+1)/2 - 1, 0, ev_bias_qmenu,
-+ MMAL_PARAMETER_EXPOSURE_COMP,
-+ &ctrl_set_value_ev,
-+ false
-+ },
-+ {
-+ V4L2_CID_EXPOSURE_AUTO_PRIORITY, MMAL_CONTROL_TYPE_STD,
-+ 0, 1,
-+ 0, 1, NULL,
-+ 0, /* Dummy MMAL ID as it gets mapped into FPS range*/
-+ &ctrl_set_exposure,
-+ false
-+ },
-+ {
-+ V4L2_CID_EXPOSURE_METERING,
-+ MMAL_CONTROL_TYPE_STD_MENU,
-+ ~0x7, 2, V4L2_EXPOSURE_METERING_AVERAGE, 0, NULL,
-+ MMAL_PARAMETER_EXP_METERING_MODE,
-+ &ctrl_set_metering_mode,
-+ false
-+ },
-+ {
-+ V4L2_CID_AUTO_N_PRESET_WHITE_BALANCE,
-+ MMAL_CONTROL_TYPE_STD_MENU,
-+ ~0x3ff, 9, V4L2_WHITE_BALANCE_AUTO, 0, NULL,
-+ MMAL_PARAMETER_AWB_MODE,
-+ &ctrl_set_awb_mode,
-+ false
-+ },
-+ {
-+ V4L2_CID_RED_BALANCE, MMAL_CONTROL_TYPE_STD,
-+ 1, 7999, 1000, 1, NULL,
-+ MMAL_PARAMETER_CUSTOM_AWB_GAINS,
-+ &ctrl_set_awb_gains,
-+ false
-+ },
-+ {
-+ V4L2_CID_BLUE_BALANCE, MMAL_CONTROL_TYPE_STD,
-+ 1, 7999, 1000, 1, NULL,
-+ MMAL_PARAMETER_CUSTOM_AWB_GAINS,
-+ &ctrl_set_awb_gains,
-+ false
-+ },
-+ {
-+ V4L2_CID_COLORFX, MMAL_CONTROL_TYPE_STD_MENU,
-+ 0, 15, V4L2_COLORFX_NONE, 0, NULL,
-+ MMAL_PARAMETER_IMAGE_EFFECT,
-+ &ctrl_set_image_effect,
-+ false
-+ },
-+ {
-+ V4L2_CID_COLORFX_CBCR, MMAL_CONTROL_TYPE_STD,
-+ 0, 0xffff, 0x8080, 1, NULL,
-+ MMAL_PARAMETER_COLOUR_EFFECT,
-+ &ctrl_set_colfx,
-+ false
-+ },
-+ {
-+ V4L2_CID_ROTATE, MMAL_CONTROL_TYPE_STD,
-+ 0, 360, 0, 90, NULL,
-+ MMAL_PARAMETER_ROTATION,
-+ &ctrl_set_rotate,
-+ false
-+ },
-+ {
-+ V4L2_CID_HFLIP, MMAL_CONTROL_TYPE_STD,
-+ 0, 1, 0, 1, NULL,
-+ MMAL_PARAMETER_MIRROR,
-+ &ctrl_set_flip,
-+ false
-+ },
-+ {
-+ V4L2_CID_VFLIP, MMAL_CONTROL_TYPE_STD,
-+ 0, 1, 0, 1, NULL,
-+ MMAL_PARAMETER_MIRROR,
-+ &ctrl_set_flip,
-+ false
-+ },
-+ {
-+ V4L2_CID_MPEG_VIDEO_BITRATE_MODE, MMAL_CONTROL_TYPE_STD_MENU,
-+ 0, ARRAY_SIZE(bitrate_mode_qmenu) - 1,
-+ 0, 0, bitrate_mode_qmenu,
-+ MMAL_PARAMETER_RATECONTROL,
-+ &ctrl_set_bitrate_mode,
-+ false
-+ },
-+ {
-+ V4L2_CID_MPEG_VIDEO_BITRATE, MMAL_CONTROL_TYPE_STD,
-+ 25*1000, 25*1000*1000, 10*1000*1000, 25*1000, NULL,
-+ MMAL_PARAMETER_VIDEO_BIT_RATE,
-+ &ctrl_set_bitrate,
-+ false
-+ },
-+ {
-+ V4L2_CID_JPEG_COMPRESSION_QUALITY, MMAL_CONTROL_TYPE_STD,
-+ 1, 100,
-+ 30, 1, NULL,
-+ MMAL_PARAMETER_JPEG_Q_FACTOR,
-+ &ctrl_set_image_encode_output,
-+ false
-+ },
-+ {
-+ V4L2_CID_POWER_LINE_FREQUENCY, MMAL_CONTROL_TYPE_STD_MENU,
-+ 0, ARRAY_SIZE(mains_freq_qmenu) - 1,
-+ 1, 1, NULL,
-+ MMAL_PARAMETER_FLICKER_AVOID,
-+ &ctrl_set_flicker_avoidance,
-+ false
-+ },
-+ {
-+ V4L2_CID_MPEG_VIDEO_REPEAT_SEQ_HEADER, MMAL_CONTROL_TYPE_STD,
-+ 0, 1,
-+ 0, 1, NULL,
-+ MMAL_PARAMETER_VIDEO_ENCODE_INLINE_HEADER,
-+ &ctrl_set_video_encode_param_output,
-+ true /* Errors ignored as requires latest firmware to work */
-+ },
-+ {
-+ V4L2_CID_MPEG_VIDEO_H264_PROFILE,
-+ MMAL_CONTROL_TYPE_STD_MENU,
-+ ~((1<<V4L2_MPEG_VIDEO_H264_PROFILE_BASELINE) |
-+ (1<<V4L2_MPEG_VIDEO_H264_PROFILE_CONSTRAINED_BASELINE) |
-+ (1<<V4L2_MPEG_VIDEO_H264_PROFILE_MAIN) |
-+ (1<<V4L2_MPEG_VIDEO_H264_PROFILE_HIGH)),
-+ V4L2_MPEG_VIDEO_H264_PROFILE_HIGH,
-+ V4L2_MPEG_VIDEO_H264_PROFILE_HIGH, 1, NULL,
-+ MMAL_PARAMETER_PROFILE,
-+ &ctrl_set_video_encode_profile_level,
-+ false
-+ },
-+ {
-+ V4L2_CID_MPEG_VIDEO_H264_LEVEL, MMAL_CONTROL_TYPE_STD_MENU,
-+ ~((1<<V4L2_MPEG_VIDEO_H264_LEVEL_1_0) |
-+ (1<<V4L2_MPEG_VIDEO_H264_LEVEL_1B) |
-+ (1<<V4L2_MPEG_VIDEO_H264_LEVEL_1_1) |
-+ (1<<V4L2_MPEG_VIDEO_H264_LEVEL_1_2) |
-+ (1<<V4L2_MPEG_VIDEO_H264_LEVEL_1_3) |
-+ (1<<V4L2_MPEG_VIDEO_H264_LEVEL_2_0) |
-+ (1<<V4L2_MPEG_VIDEO_H264_LEVEL_2_1) |
-+ (1<<V4L2_MPEG_VIDEO_H264_LEVEL_2_2) |
-+ (1<<V4L2_MPEG_VIDEO_H264_LEVEL_3_0) |
-+ (1<<V4L2_MPEG_VIDEO_H264_LEVEL_3_1) |
-+ (1<<V4L2_MPEG_VIDEO_H264_LEVEL_3_2) |
-+ (1<<V4L2_MPEG_VIDEO_H264_LEVEL_4_0)),
-+ V4L2_MPEG_VIDEO_H264_LEVEL_4_0,
-+ V4L2_MPEG_VIDEO_H264_LEVEL_4_0, 1, NULL,
-+ MMAL_PARAMETER_PROFILE,
-+ &ctrl_set_video_encode_profile_level,
-+ false
-+ },
-+ {
-+ V4L2_CID_SCENE_MODE, MMAL_CONTROL_TYPE_STD_MENU,
-+ -1, /* Min is computed at runtime */
-+ V4L2_SCENE_MODE_TEXT,
-+ V4L2_SCENE_MODE_NONE, 1, NULL,
-+ MMAL_PARAMETER_PROFILE,
-+ &ctrl_set_scene_mode,
-+ false
-+ },
-+ {
-+ V4L2_CID_MPEG_VIDEO_H264_I_PERIOD, MMAL_CONTROL_TYPE_STD,
-+ 0, 0x7FFFFFFF, 60, 1, NULL,
-+ MMAL_PARAMETER_INTRAPERIOD,
-+ &ctrl_set_video_encode_param_output,
-+ false
-+ },
-+};
-+
-+int bm2835_mmal_set_all_camera_controls(struct bm2835_mmal_dev *dev)
-+{
-+ int c;
-+ int ret = 0;
-+
-+ for (c = 0; c < V4L2_CTRL_COUNT; c++) {
-+ if ((dev->ctrls[c]) && (v4l2_ctrls[c].setter)) {
-+ ret = v4l2_ctrls[c].setter(dev, dev->ctrls[c],
-+ &v4l2_ctrls[c]);
-+ if (!v4l2_ctrls[c].ignore_errors && ret) {
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "Failed when setting default values for ctrl %d\n",
-+ c);
-+ break;
-+ }
-+ }
-+ }
-+ return ret;
-+}
-+
-+int set_framerate_params(struct bm2835_mmal_dev *dev)
-+{
-+ struct mmal_parameter_fps_range fps_range;
-+ int ret;
-+
-+ if ((dev->exposure_mode_active != MMAL_PARAM_EXPOSUREMODE_OFF) &&
-+ (dev->exp_auto_priority)) {
-+ /* Variable FPS. Define min FPS as 1fps.
-+ * Max as max defined FPS.
-+ */
-+ fps_range.fps_low.num = 1;
-+ fps_range.fps_low.den = 1;
-+ fps_range.fps_high.num = dev->capture.timeperframe.denominator;
-+ fps_range.fps_high.den = dev->capture.timeperframe.numerator;
-+ } else {
-+ /* Fixed FPS - set min and max to be the same */
-+ fps_range.fps_low.num = fps_range.fps_high.num =
-+ dev->capture.timeperframe.denominator;
-+ fps_range.fps_low.den = fps_range.fps_high.den =
-+ dev->capture.timeperframe.numerator;
-+ }
-+
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "Set fps range to %d/%d to %d/%d\n",
-+ fps_range.fps_low.num,
-+ fps_range.fps_low.den,
-+ fps_range.fps_high.num,
-+ fps_range.fps_high.den
-+ );
-+
-+ ret = vchiq_mmal_port_parameter_set(dev->instance,
-+ &dev->component[MMAL_COMPONENT_CAMERA]->
-+ output[MMAL_CAMERA_PORT_PREVIEW],
-+ MMAL_PARAMETER_FPS_RANGE,
-+ &fps_range, sizeof(fps_range));
-+ ret += vchiq_mmal_port_parameter_set(dev->instance,
-+ &dev->component[MMAL_COMPONENT_CAMERA]->
-+ output[MMAL_CAMERA_PORT_VIDEO],
-+ MMAL_PARAMETER_FPS_RANGE,
-+ &fps_range, sizeof(fps_range));
-+ ret += vchiq_mmal_port_parameter_set(dev->instance,
-+ &dev->component[MMAL_COMPONENT_CAMERA]->
-+ output[MMAL_CAMERA_PORT_CAPTURE],
-+ MMAL_PARAMETER_FPS_RANGE,
-+ &fps_range, sizeof(fps_range));
-+ if (ret)
-+ v4l2_dbg(0, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "Failed to set fps ret %d\n",
-+ ret);
-+
-+ return ret;
-+
-+}
-+
-+int bm2835_mmal_init_controls(struct bm2835_mmal_dev *dev,
-+ struct v4l2_ctrl_handler *hdl)
-+{
-+ int c;
-+ const struct bm2835_mmal_v4l2_ctrl *ctrl;
-+
-+ v4l2_ctrl_handler_init(hdl, V4L2_CTRL_COUNT);
-+
-+ for (c = 0; c < V4L2_CTRL_COUNT; c++) {
-+ ctrl = &v4l2_ctrls[c];
-+
-+ switch (ctrl->type) {
-+ case MMAL_CONTROL_TYPE_STD:
-+ dev->ctrls[c] = v4l2_ctrl_new_std(hdl,
-+ &bm2835_mmal_ctrl_ops, ctrl->id,
-+ ctrl->min, ctrl->max, ctrl->step, ctrl->def);
-+ break;
-+
-+ case MMAL_CONTROL_TYPE_STD_MENU:
-+ {
-+ int mask = ctrl->min;
-+
-+ if (ctrl->id == V4L2_CID_SCENE_MODE) {
-+ /* Special handling to work out the mask
-+ * value based on the scene_configs array
-+ * at runtime. Reduces the chance of
-+ * mismatches.
-+ */
-+ int i;
-+ mask = 1<<V4L2_SCENE_MODE_NONE;
-+ for (i = 0;
-+ i < ARRAY_SIZE(scene_configs);
-+ i++) {
-+ mask |= 1<<scene_configs[i].v4l2_scene;
-+ }
-+ mask = ~mask;
-+ }
-+
-+ dev->ctrls[c] = v4l2_ctrl_new_std_menu(hdl,
-+ &bm2835_mmal_ctrl_ops, ctrl->id,
-+ ctrl->max, mask, ctrl->def);
-+ break;
-+ }
-+
-+ case MMAL_CONTROL_TYPE_INT_MENU:
-+ dev->ctrls[c] = v4l2_ctrl_new_int_menu(hdl,
-+ &bm2835_mmal_ctrl_ops, ctrl->id,
-+ ctrl->max, ctrl->def, ctrl->imenu);
-+ break;
-+
-+ case MMAL_CONTROL_TYPE_CLUSTER:
-+ /* skip this entry when constructing controls */
-+ continue;
-+ }
-+
-+ if (hdl->error)
-+ break;
-+
-+ dev->ctrls[c]->priv = (void *)ctrl;
-+ }
-+
-+ if (hdl->error) {
-+ pr_err("error adding control %d/%d id 0x%x\n", c,
-+ V4L2_CTRL_COUNT, ctrl->id);
-+ return hdl->error;
-+ }
-+
-+ for (c = 0; c < V4L2_CTRL_COUNT; c++) {
-+ ctrl = &v4l2_ctrls[c];
-+
-+ switch (ctrl->type) {
-+ case MMAL_CONTROL_TYPE_CLUSTER:
-+ v4l2_ctrl_auto_cluster(ctrl->min,
-+ &dev->ctrls[c+1],
-+ ctrl->max,
-+ ctrl->def);
-+ break;
-+
-+ case MMAL_CONTROL_TYPE_STD:
-+ case MMAL_CONTROL_TYPE_STD_MENU:
-+ case MMAL_CONTROL_TYPE_INT_MENU:
-+ break;
-+ }
-+
-+ }
-+
-+ return 0;
-+}
---- /dev/null
-+++ b/drivers/media/platform/bcm2835/mmal-common.h
-@@ -0,0 +1,53 @@
-+/*
-+ * Broadcom BM2835 V4L2 driver
-+ *
-+ * Copyright © 2013 Raspberry Pi (Trading) Ltd.
-+ *
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License. See the file COPYING in the main directory of this archive
-+ * for more details.
-+ *
-+ * Authors: Vincent Sanders <vincent.sanders at collabora.co.uk>
-+ * Dave Stevenson <dsteve at broadcom.com>
-+ * Simon Mellor <simellor at broadcom.com>
-+ * Luke Diamand <luked at broadcom.com>
-+ *
-+ * MMAL structures
-+ *
-+ */
-+
-+#define MMAL_FOURCC(a, b, c, d) ((a) | (b << 8) | (c << 16) | (d << 24))
-+#define MMAL_MAGIC MMAL_FOURCC('m', 'm', 'a', 'l')
-+
-+/** Special value signalling that time is not known */
-+#define MMAL_TIME_UNKNOWN (1LL<<63)
-+
-+/* mapping between v4l and mmal video modes */
-+struct mmal_fmt {
-+ char *name;
-+ u32 fourcc; /* v4l2 format id */
-+ int flags; /* v4l2 flags field */
-+ u32 mmal;
-+ int depth;
-+ u32 mmal_component; /* MMAL component index to be used to encode */
-+ u32 ybbp; /* depth of first Y plane for planar formats */
-+};
-+
-+/* buffer for one video frame */
-+struct mmal_buffer {
-+ /* v4l buffer data -- must be first */
-+ struct vb2_v4l2_buffer vb;
-+
-+ /* list of buffers available */
-+ struct list_head list;
-+
-+ void *buffer; /* buffer pointer */
-+ unsigned long buffer_size; /* size of allocated buffer */
-+};
-+
-+/* */
-+struct mmal_colourfx {
-+ s32 enable;
-+ u32 u;
-+ u32 v;
-+};
---- /dev/null
-+++ b/drivers/media/platform/bcm2835/mmal-encodings.h
-@@ -0,0 +1,127 @@
-+/*
-+ * Broadcom BM2835 V4L2 driver
-+ *
-+ * Copyright © 2013 Raspberry Pi (Trading) Ltd.
-+ *
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License. See the file COPYING in the main directory of this archive
-+ * for more details.
-+ *
-+ * Authors: Vincent Sanders <vincent.sanders at collabora.co.uk>
-+ * Dave Stevenson <dsteve at broadcom.com>
-+ * Simon Mellor <simellor at broadcom.com>
-+ * Luke Diamand <luked at broadcom.com>
-+ */
-+#ifndef MMAL_ENCODINGS_H
-+#define MMAL_ENCODINGS_H
-+
-+#define MMAL_ENCODING_H264 MMAL_FOURCC('H', '2', '6', '4')
-+#define MMAL_ENCODING_H263 MMAL_FOURCC('H', '2', '6', '3')
-+#define MMAL_ENCODING_MP4V MMAL_FOURCC('M', 'P', '4', 'V')
-+#define MMAL_ENCODING_MP2V MMAL_FOURCC('M', 'P', '2', 'V')
-+#define MMAL_ENCODING_MP1V MMAL_FOURCC('M', 'P', '1', 'V')
-+#define MMAL_ENCODING_WMV3 MMAL_FOURCC('W', 'M', 'V', '3')
-+#define MMAL_ENCODING_WMV2 MMAL_FOURCC('W', 'M', 'V', '2')
-+#define MMAL_ENCODING_WMV1 MMAL_FOURCC('W', 'M', 'V', '1')
-+#define MMAL_ENCODING_WVC1 MMAL_FOURCC('W', 'V', 'C', '1')
-+#define MMAL_ENCODING_VP8 MMAL_FOURCC('V', 'P', '8', ' ')
-+#define MMAL_ENCODING_VP7 MMAL_FOURCC('V', 'P', '7', ' ')
-+#define MMAL_ENCODING_VP6 MMAL_FOURCC('V', 'P', '6', ' ')
-+#define MMAL_ENCODING_THEORA MMAL_FOURCC('T', 'H', 'E', 'O')
-+#define MMAL_ENCODING_SPARK MMAL_FOURCC('S', 'P', 'R', 'K')
-+#define MMAL_ENCODING_MJPEG MMAL_FOURCC('M', 'J', 'P', 'G')
-+
-+#define MMAL_ENCODING_JPEG MMAL_FOURCC('J', 'P', 'E', 'G')
-+#define MMAL_ENCODING_GIF MMAL_FOURCC('G', 'I', 'F', ' ')
-+#define MMAL_ENCODING_PNG MMAL_FOURCC('P', 'N', 'G', ' ')
-+#define MMAL_ENCODING_PPM MMAL_FOURCC('P', 'P', 'M', ' ')
-+#define MMAL_ENCODING_TGA MMAL_FOURCC('T', 'G', 'A', ' ')
-+#define MMAL_ENCODING_BMP MMAL_FOURCC('B', 'M', 'P', ' ')
-+
-+#define MMAL_ENCODING_I420 MMAL_FOURCC('I', '4', '2', '0')
-+#define MMAL_ENCODING_I420_SLICE MMAL_FOURCC('S', '4', '2', '0')
-+#define MMAL_ENCODING_YV12 MMAL_FOURCC('Y', 'V', '1', '2')
-+#define MMAL_ENCODING_I422 MMAL_FOURCC('I', '4', '2', '2')
-+#define MMAL_ENCODING_I422_SLICE MMAL_FOURCC('S', '4', '2', '2')
-+#define MMAL_ENCODING_YUYV MMAL_FOURCC('Y', 'U', 'Y', 'V')
-+#define MMAL_ENCODING_YVYU MMAL_FOURCC('Y', 'V', 'Y', 'U')
-+#define MMAL_ENCODING_UYVY MMAL_FOURCC('U', 'Y', 'V', 'Y')
-+#define MMAL_ENCODING_VYUY MMAL_FOURCC('V', 'Y', 'U', 'Y')
-+#define MMAL_ENCODING_NV12 MMAL_FOURCC('N', 'V', '1', '2')
-+#define MMAL_ENCODING_NV21 MMAL_FOURCC('N', 'V', '2', '1')
-+#define MMAL_ENCODING_ARGB MMAL_FOURCC('A', 'R', 'G', 'B')
-+#define MMAL_ENCODING_RGBA MMAL_FOURCC('R', 'G', 'B', 'A')
-+#define MMAL_ENCODING_ABGR MMAL_FOURCC('A', 'B', 'G', 'R')
-+#define MMAL_ENCODING_BGRA MMAL_FOURCC('B', 'G', 'R', 'A')
-+#define MMAL_ENCODING_RGB16 MMAL_FOURCC('R', 'G', 'B', '2')
-+#define MMAL_ENCODING_RGB24 MMAL_FOURCC('R', 'G', 'B', '3')
-+#define MMAL_ENCODING_RGB32 MMAL_FOURCC('R', 'G', 'B', '4')
-+#define MMAL_ENCODING_BGR16 MMAL_FOURCC('B', 'G', 'R', '2')
-+#define MMAL_ENCODING_BGR24 MMAL_FOURCC('B', 'G', 'R', '3')
-+#define MMAL_ENCODING_BGR32 MMAL_FOURCC('B', 'G', 'R', '4')
-+
-+/** SAND Video (YUVUV128) format, native format understood by VideoCore.
-+ * This format is *not* opaque - if requested you will receive full frames
-+ * of YUV_UV video.
-+ */
-+#define MMAL_ENCODING_YUVUV128 MMAL_FOURCC('S', 'A', 'N', 'D')
-+
-+/** VideoCore opaque image format, image handles are returned to
-+ * the host but not the actual image data.
-+ */
-+#define MMAL_ENCODING_OPAQUE MMAL_FOURCC('O', 'P', 'Q', 'V')
-+
-+/** An EGL image handle
-+ */
-+#define MMAL_ENCODING_EGL_IMAGE MMAL_FOURCC('E', 'G', 'L', 'I')
-+
-+/* }@ */
-+
-+/** \name Pre-defined audio encodings */
-+/* @{ */
-+#define MMAL_ENCODING_PCM_UNSIGNED_BE MMAL_FOURCC('P', 'C', 'M', 'U')
-+#define MMAL_ENCODING_PCM_UNSIGNED_LE MMAL_FOURCC('p', 'c', 'm', 'u')
-+#define MMAL_ENCODING_PCM_SIGNED_BE MMAL_FOURCC('P', 'C', 'M', 'S')
-+#define MMAL_ENCODING_PCM_SIGNED_LE MMAL_FOURCC('p', 'c', 'm', 's')
-+#define MMAL_ENCODING_PCM_FLOAT_BE MMAL_FOURCC('P', 'C', 'M', 'F')
-+#define MMAL_ENCODING_PCM_FLOAT_LE MMAL_FOURCC('p', 'c', 'm', 'f')
-+
-+/* Pre-defined H264 encoding variants */
-+
-+/** ISO 14496-10 Annex B byte stream format */
-+#define MMAL_ENCODING_VARIANT_H264_DEFAULT 0
-+/** ISO 14496-15 AVC stream format */
-+#define MMAL_ENCODING_VARIANT_H264_AVC1 MMAL_FOURCC('A', 'V', 'C', '1')
-+/** Implicitly delineated NAL units without emulation prevention */
-+#define MMAL_ENCODING_VARIANT_H264_RAW MMAL_FOURCC('R', 'A', 'W', ' ')
-+
-+
-+/** \defgroup MmalColorSpace List of pre-defined video color spaces
-+ * This defines a list of common color spaces. This list isn't exhaustive and
-+ * is only provided as a convenience to avoid clients having to use FourCC
-+ * codes directly. However components are allowed to define and use their own
-+ * FourCC codes.
-+ */
-+/* @{ */
-+
-+/** Unknown color space */
-+#define MMAL_COLOR_SPACE_UNKNOWN 0
-+/** ITU-R BT.601-5 [SDTV] */
-+#define MMAL_COLOR_SPACE_ITUR_BT601 MMAL_FOURCC('Y', '6', '0', '1')
-+/** ITU-R BT.709-3 [HDTV] */
-+#define MMAL_COLOR_SPACE_ITUR_BT709 MMAL_FOURCC('Y', '7', '0', '9')
-+/** JPEG JFIF */
-+#define MMAL_COLOR_SPACE_JPEG_JFIF MMAL_FOURCC('Y', 'J', 'F', 'I')
-+/** Title 47 Code of Federal Regulations (2003) 73.682 (a) (20) */
-+#define MMAL_COLOR_SPACE_FCC MMAL_FOURCC('Y', 'F', 'C', 'C')
-+/** Society of Motion Picture and Television Engineers 240M (1999) */
-+#define MMAL_COLOR_SPACE_SMPTE240M MMAL_FOURCC('Y', '2', '4', '0')
-+/** ITU-R BT.470-2 System M */
-+#define MMAL_COLOR_SPACE_BT470_2_M MMAL_FOURCC('Y', '_', '_', 'M')
-+/** ITU-R BT.470-2 System BG */
-+#define MMAL_COLOR_SPACE_BT470_2_BG MMAL_FOURCC('Y', '_', 'B', 'G')
-+/** JPEG JFIF, but with 16..255 luma */
-+#define MMAL_COLOR_SPACE_JFIF_Y16_255 MMAL_FOURCC('Y', 'Y', '1', '6')
-+/* @} MmalColorSpace List */
-+
-+#endif /* MMAL_ENCODINGS_H */
---- /dev/null
-+++ b/drivers/media/platform/bcm2835/mmal-msg-common.h
-@@ -0,0 +1,50 @@
-+/*
-+ * Broadcom BM2835 V4L2 driver
-+ *
-+ * Copyright © 2013 Raspberry Pi (Trading) Ltd.
-+ *
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License. See the file COPYING in the main directory of this archive
-+ * for more details.
-+ *
-+ * Authors: Vincent Sanders <vincent.sanders at collabora.co.uk>
-+ * Dave Stevenson <dsteve at broadcom.com>
-+ * Simon Mellor <simellor at broadcom.com>
-+ * Luke Diamand <luked at broadcom.com>
-+ */
-+
-+#ifndef MMAL_MSG_COMMON_H
-+#define MMAL_MSG_COMMON_H
-+
-+enum mmal_msg_status {
-+ MMAL_MSG_STATUS_SUCCESS = 0, /**< Success */
-+ MMAL_MSG_STATUS_ENOMEM, /**< Out of memory */
-+ MMAL_MSG_STATUS_ENOSPC, /**< Out of resources other than memory */
-+ MMAL_MSG_STATUS_EINVAL, /**< Argument is invalid */
-+ MMAL_MSG_STATUS_ENOSYS, /**< Function not implemented */
-+ MMAL_MSG_STATUS_ENOENT, /**< No such file or directory */
-+ MMAL_MSG_STATUS_ENXIO, /**< No such device or address */
-+ MMAL_MSG_STATUS_EIO, /**< I/O error */
-+ MMAL_MSG_STATUS_ESPIPE, /**< Illegal seek */
-+ MMAL_MSG_STATUS_ECORRUPT, /**< Data is corrupt \attention */
-+ MMAL_MSG_STATUS_ENOTREADY, /**< Component is not ready */
-+ MMAL_MSG_STATUS_ECONFIG, /**< Component is not configured */
-+ MMAL_MSG_STATUS_EISCONN, /**< Port is already connected */
-+ MMAL_MSG_STATUS_ENOTCONN, /**< Port is disconnected */
-+ MMAL_MSG_STATUS_EAGAIN, /**< Resource temporarily unavailable. */
-+ MMAL_MSG_STATUS_EFAULT, /**< Bad address */
-+};
-+
-+struct mmal_rect {
-+ s32 x; /**< x coordinate (from left) */
-+ s32 y; /**< y coordinate (from top) */
-+ s32 width; /**< width */
-+ s32 height; /**< height */
-+};
-+
-+struct mmal_rational {
-+ s32 num; /**< Numerator */
-+ s32 den; /**< Denominator */
-+};
-+
-+#endif /* MMAL_MSG_COMMON_H */
---- /dev/null
-+++ b/drivers/media/platform/bcm2835/mmal-msg-format.h
-@@ -0,0 +1,81 @@
-+/*
-+ * Broadcom BM2835 V4L2 driver
-+ *
-+ * Copyright © 2013 Raspberry Pi (Trading) Ltd.
-+ *
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License. See the file COPYING in the main directory of this archive
-+ * for more details.
-+ *
-+ * Authors: Vincent Sanders <vincent.sanders at collabora.co.uk>
-+ * Dave Stevenson <dsteve at broadcom.com>
-+ * Simon Mellor <simellor at broadcom.com>
-+ * Luke Diamand <luked at broadcom.com>
-+ */
-+
-+#ifndef MMAL_MSG_FORMAT_H
-+#define MMAL_MSG_FORMAT_H
-+
-+#include "mmal-msg-common.h"
-+
-+/* MMAL_ES_FORMAT_T */
-+
-+
-+struct mmal_audio_format {
-+ u32 channels; /**< Number of audio channels */
-+ u32 sample_rate; /**< Sample rate */
-+
-+ u32 bits_per_sample; /**< Bits per sample */
-+ u32 block_align; /**< Size of a block of data */
-+};
-+
-+struct mmal_video_format {
-+ u32 width; /**< Width of frame in pixels */
-+ u32 height; /**< Height of frame in rows of pixels */
-+ struct mmal_rect crop; /**< Visible region of the frame */
-+ struct mmal_rational frame_rate; /**< Frame rate */
-+ struct mmal_rational par; /**< Pixel aspect ratio */
-+
-+ /* FourCC specifying the color space of the video stream. See the
-+ * \ref MmalColorSpace "pre-defined color spaces" for some examples.
-+ */
-+ u32 color_space;
-+};
-+
-+struct mmal_subpicture_format {
-+ u32 x_offset;
-+ u32 y_offset;
-+};
-+
-+union mmal_es_specific_format {
-+ struct mmal_audio_format audio;
-+ struct mmal_video_format video;
-+ struct mmal_subpicture_format subpicture;
-+};
-+
-+/** Definition of an elementary stream format (MMAL_ES_FORMAT_T) */
-+struct mmal_es_format {
-+ u32 type; /* enum mmal_es_type */
-+
-+ u32 encoding; /* FourCC specifying encoding of the elementary stream.*/
-+ u32 encoding_variant; /* FourCC specifying the specific
-+ * encoding variant of the elementary
-+ * stream.
-+ */
-+
-+ union mmal_es_specific_format *es; /* TODO: pointers in
-+ * message serialisation?!?
-+ */
-+ /* Type specific
-+ * information for the
-+ * elementary stream
-+ */
-+
-+ u32 bitrate; /**< Bitrate in bits per second */
-+ u32 flags; /**< Flags describing properties of the elementary stream. */
-+
-+ u32 extradata_size; /**< Size of the codec specific data */
-+ u8 *extradata; /**< Codec specific data */
-+};
-+
-+#endif /* MMAL_MSG_FORMAT_H */
---- /dev/null
-+++ b/drivers/media/platform/bcm2835/mmal-msg-port.h
-@@ -0,0 +1,107 @@
-+/*
-+ * Broadcom BM2835 V4L2 driver
-+ *
-+ * Copyright © 2013 Raspberry Pi (Trading) Ltd.
-+ *
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License. See the file COPYING in the main directory of this archive
-+ * for more details.
-+ *
-+ * Authors: Vincent Sanders <vincent.sanders at collabora.co.uk>
-+ * Dave Stevenson <dsteve at broadcom.com>
-+ * Simon Mellor <simellor at broadcom.com>
-+ * Luke Diamand <luked at broadcom.com>
-+ */
-+
-+/* MMAL_PORT_TYPE_T */
-+enum mmal_port_type {
-+ MMAL_PORT_TYPE_UNKNOWN = 0, /**< Unknown port type */
-+ MMAL_PORT_TYPE_CONTROL, /**< Control port */
-+ MMAL_PORT_TYPE_INPUT, /**< Input port */
-+ MMAL_PORT_TYPE_OUTPUT, /**< Output port */
-+ MMAL_PORT_TYPE_CLOCK, /**< Clock port */
-+};
-+
-+/** The port is pass-through and doesn't need buffer headers allocated */
-+#define MMAL_PORT_CAPABILITY_PASSTHROUGH 0x01
-+/** The port wants to allocate the buffer payloads.
-+ * This signals a preference that payload allocation should be done
-+ * on this port for efficiency reasons. */
-+#define MMAL_PORT_CAPABILITY_ALLOCATION 0x02
-+/** The port supports format change events.
-+ * This applies to input ports and is used to let the client know
-+ * whether the port supports being reconfigured via a format
-+ * change event (i.e. without having to disable the port). */
-+#define MMAL_PORT_CAPABILITY_SUPPORTS_EVENT_FORMAT_CHANGE 0x04
-+
-+/* mmal port structure (MMAL_PORT_T)
-+ *
-+ * most elements are informational only, the pointer values for
-+ * interogation messages are generally provided as additional
-+ * strucures within the message. When used to set values only teh
-+ * buffer_num, buffer_size and userdata parameters are writable.
-+ */
-+struct mmal_port {
-+ void *priv; /* Private member used by the framework */
-+ const char *name; /* Port name. Used for debugging purposes (RO) */
-+
-+ u32 type; /* Type of the port (RO) enum mmal_port_type */
-+ u16 index; /* Index of the port in its type list (RO) */
-+ u16 index_all; /* Index of the port in the list of all ports (RO) */
-+
-+ u32 is_enabled; /* Indicates whether the port is enabled or not (RO) */
-+ struct mmal_es_format *format; /* Format of the elementary stream */
-+
-+ u32 buffer_num_min; /* Minimum number of buffers the port
-+ * requires (RO). This is set by the
-+ * component.
-+ */
-+
-+ u32 buffer_size_min; /* Minimum size of buffers the port
-+ * requires (RO). This is set by the
-+ * component.
-+ */
-+
-+ u32 buffer_alignment_min; /* Minimum alignment requirement for
-+ * the buffers (RO). A value of
-+ * zero means no special alignment
-+ * requirements. This is set by the
-+ * component.
-+ */
-+
-+ u32 buffer_num_recommended; /* Number of buffers the port
-+ * recommends for optimal
-+ * performance (RO). A value of
-+ * zero means no special
-+ * recommendation. This is set
-+ * by the component.
-+ */
-+
-+ u32 buffer_size_recommended; /* Size of buffers the port
-+ * recommends for optimal
-+ * performance (RO). A value of
-+ * zero means no special
-+ * recommendation. This is set
-+ * by the component.
-+ */
-+
-+ u32 buffer_num; /* Actual number of buffers the port will use.
-+ * This is set by the client.
-+ */
-+
-+ u32 buffer_size; /* Actual maximum size of the buffers that
-+ * will be sent to the port. This is set by
-+ * the client.
-+ */
-+
-+ void *component; /* Component this port belongs to (Read Only) */
-+
-+ void *userdata; /* Field reserved for use by the client */
-+
-+ u32 capabilities; /* Flags describing the capabilities of a
-+ * port (RO). Bitwise combination of \ref
-+ * portcapabilities "Port capabilities"
-+ * values.
-+ */
-+
-+};
---- /dev/null
-+++ b/drivers/media/platform/bcm2835/mmal-msg.h
-@@ -0,0 +1,404 @@
-+/*
-+ * Broadcom BM2835 V4L2 driver
-+ *
-+ * Copyright © 2013 Raspberry Pi (Trading) Ltd.
-+ *
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License. See the file COPYING in the main directory of this archive
-+ * for more details.
-+ *
-+ * Authors: Vincent Sanders <vincent.sanders at collabora.co.uk>
-+ * Dave Stevenson <dsteve at broadcom.com>
-+ * Simon Mellor <simellor at broadcom.com>
-+ * Luke Diamand <luked at broadcom.com>
-+ */
-+
-+/* all the data structures which serialise the MMAL protocol. note
-+ * these are directly mapped onto the recived message data.
-+ *
-+ * BEWARE: They seem to *assume* pointers are u32 and that there is no
-+ * structure padding!
-+ *
-+ * NOTE: this implementation uses kernel types to ensure sizes. Rather
-+ * than assigning values to enums to force their size the
-+ * implementation uses fixed size types and not the enums (though the
-+ * comments have the actual enum type
-+ */
-+
-+#define VC_MMAL_VER 15
-+#define VC_MMAL_MIN_VER 10
-+#define VC_MMAL_SERVER_NAME MAKE_FOURCC("mmal")
-+
-+/* max total message size is 512 bytes */
-+#define MMAL_MSG_MAX_SIZE 512
-+/* with six 32bit header elements max payload is therefore 488 bytes */
-+#define MMAL_MSG_MAX_PAYLOAD 488
-+
-+#include "mmal-msg-common.h"
-+#include "mmal-msg-format.h"
-+#include "mmal-msg-port.h"
-+
-+enum mmal_msg_type {
-+ MMAL_MSG_TYPE_QUIT = 1,
-+ MMAL_MSG_TYPE_SERVICE_CLOSED,
-+ MMAL_MSG_TYPE_GET_VERSION,
-+ MMAL_MSG_TYPE_COMPONENT_CREATE,
-+ MMAL_MSG_TYPE_COMPONENT_DESTROY, /* 5 */
-+ MMAL_MSG_TYPE_COMPONENT_ENABLE,
-+ MMAL_MSG_TYPE_COMPONENT_DISABLE,
-+ MMAL_MSG_TYPE_PORT_INFO_GET,
-+ MMAL_MSG_TYPE_PORT_INFO_SET,
-+ MMAL_MSG_TYPE_PORT_ACTION, /* 10 */
-+ MMAL_MSG_TYPE_BUFFER_FROM_HOST,
-+ MMAL_MSG_TYPE_BUFFER_TO_HOST,
-+ MMAL_MSG_TYPE_GET_STATS,
-+ MMAL_MSG_TYPE_PORT_PARAMETER_SET,
-+ MMAL_MSG_TYPE_PORT_PARAMETER_GET, /* 15 */
-+ MMAL_MSG_TYPE_EVENT_TO_HOST,
-+ MMAL_MSG_TYPE_GET_CORE_STATS_FOR_PORT,
-+ MMAL_MSG_TYPE_OPAQUE_ALLOCATOR,
-+ MMAL_MSG_TYPE_CONSUME_MEM,
-+ MMAL_MSG_TYPE_LMK, /* 20 */
-+ MMAL_MSG_TYPE_OPAQUE_ALLOCATOR_DESC,
-+ MMAL_MSG_TYPE_DRM_GET_LHS32,
-+ MMAL_MSG_TYPE_DRM_GET_TIME,
-+ MMAL_MSG_TYPE_BUFFER_FROM_HOST_ZEROLEN,
-+ MMAL_MSG_TYPE_PORT_FLUSH, /* 25 */
-+ MMAL_MSG_TYPE_HOST_LOG,
-+ MMAL_MSG_TYPE_MSG_LAST
-+};
-+
-+/* port action request messages differ depending on the action type */
-+enum mmal_msg_port_action_type {
-+ MMAL_MSG_PORT_ACTION_TYPE_UNKNOWN = 0, /* Unkown action */
-+ MMAL_MSG_PORT_ACTION_TYPE_ENABLE, /* Enable a port */
-+ MMAL_MSG_PORT_ACTION_TYPE_DISABLE, /* Disable a port */
-+ MMAL_MSG_PORT_ACTION_TYPE_FLUSH, /* Flush a port */
-+ MMAL_MSG_PORT_ACTION_TYPE_CONNECT, /* Connect ports */
-+ MMAL_MSG_PORT_ACTION_TYPE_DISCONNECT, /* Disconnect ports */
-+ MMAL_MSG_PORT_ACTION_TYPE_SET_REQUIREMENTS, /* Set buffer requirements*/
-+};
-+
-+struct mmal_msg_header {
-+ u32 magic;
-+ u32 type; /** enum mmal_msg_type */
-+
-+ /* Opaque handle to the control service */
-+ struct mmal_control_service *control_service;
-+
-+ struct mmal_msg_context *context; /** a u32 per message context */
-+ u32 status; /** The status of the vchiq operation */
-+ u32 padding;
-+};
-+
-+/* Send from VC to host to report version */
-+struct mmal_msg_version {
-+ u32 flags;
-+ u32 major;
-+ u32 minor;
-+ u32 minimum;
-+};
-+
-+/* request to VC to create component */
-+struct mmal_msg_component_create {
-+ void *client_component; /* component context */
-+ char name[128];
-+ u32 pid; /* For debug */
-+};
-+
-+/* reply from VC to component creation request */
-+struct mmal_msg_component_create_reply {
-+ u32 status; /** enum mmal_msg_status - how does this differ to
-+ * the one in the header?
-+ */
-+ u32 component_handle; /* VideoCore handle for component */
-+ u32 input_num; /* Number of input ports */
-+ u32 output_num; /* Number of output ports */
-+ u32 clock_num; /* Number of clock ports */
-+};
-+
-+/* request to VC to destroy a component */
-+struct mmal_msg_component_destroy {
-+ u32 component_handle;
-+};
-+
-+struct mmal_msg_component_destroy_reply {
-+ u32 status; /** The component destruction status */
-+};
-+
-+
-+/* request and reply to VC to enable a component */
-+struct mmal_msg_component_enable {
-+ u32 component_handle;
-+};
-+
-+struct mmal_msg_component_enable_reply {
-+ u32 status; /** The component enable status */
-+};
-+
-+
-+/* request and reply to VC to disable a component */
-+struct mmal_msg_component_disable {
-+ u32 component_handle;
-+};
-+
-+struct mmal_msg_component_disable_reply {
-+ u32 status; /** The component disable status */
-+};
-+
-+/* request to VC to get port information */
-+struct mmal_msg_port_info_get {
-+ u32 component_handle; /* component handle port is associated with */
-+ u32 port_type; /* enum mmal_msg_port_type */
-+ u32 index; /* port index to query */
-+};
-+
-+/* reply from VC to get port info request */
-+struct mmal_msg_port_info_get_reply {
-+ u32 status; /** enum mmal_msg_status */
-+ u32 component_handle; /* component handle port is associated with */
-+ u32 port_type; /* enum mmal_msg_port_type */
-+ u32 port_index; /* port indexed in query */
-+ s32 found; /* unused */
-+ u32 port_handle; /**< Handle to use for this port */
-+ struct mmal_port port;
-+ struct mmal_es_format format; /* elementry stream format */
-+ union mmal_es_specific_format es; /* es type specific data */
-+ u8 extradata[MMAL_FORMAT_EXTRADATA_MAX_SIZE]; /* es extra data */
-+};
-+
-+/* request to VC to set port information */
-+struct mmal_msg_port_info_set {
-+ u32 component_handle;
-+ u32 port_type; /* enum mmal_msg_port_type */
-+ u32 port_index; /* port indexed in query */
-+ struct mmal_port port;
-+ struct mmal_es_format format;
-+ union mmal_es_specific_format es;
-+ u8 extradata[MMAL_FORMAT_EXTRADATA_MAX_SIZE];
-+};
-+
-+/* reply from VC to port info set request */
-+struct mmal_msg_port_info_set_reply {
-+ u32 status;
-+ u32 component_handle; /* component handle port is associated with */
-+ u32 port_type; /* enum mmal_msg_port_type */
-+ u32 index; /* port indexed in query */
-+ s32 found; /* unused */
-+ u32 port_handle; /**< Handle to use for this port */
-+ struct mmal_port port;
-+ struct mmal_es_format format;
-+ union mmal_es_specific_format es;
-+ u8 extradata[MMAL_FORMAT_EXTRADATA_MAX_SIZE];
-+};
-+
-+
-+/* port action requests that take a mmal_port as a parameter */
-+struct mmal_msg_port_action_port {
-+ u32 component_handle;
-+ u32 port_handle;
-+ u32 action; /* enum mmal_msg_port_action_type */
-+ struct mmal_port port;
-+};
-+
-+/* port action requests that take handles as a parameter */
-+struct mmal_msg_port_action_handle {
-+ u32 component_handle;
-+ u32 port_handle;
-+ u32 action; /* enum mmal_msg_port_action_type */
-+ u32 connect_component_handle;
-+ u32 connect_port_handle;
-+};
-+
-+struct mmal_msg_port_action_reply {
-+ u32 status; /** The port action operation status */
-+};
-+
-+
-+
-+
-+/* MMAL buffer transfer */
-+
-+/** Size of space reserved in a buffer message for short messages. */
-+#define MMAL_VC_SHORT_DATA 128
-+
-+/** Signals that the current payload is the end of the stream of data */
-+#define MMAL_BUFFER_HEADER_FLAG_EOS (1<<0)
-+/** Signals that the start of the current payload starts a frame */
-+#define MMAL_BUFFER_HEADER_FLAG_FRAME_START (1<<1)
-+/** Signals that the end of the current payload ends a frame */
-+#define MMAL_BUFFER_HEADER_FLAG_FRAME_END (1<<2)
-+/** Signals that the current payload contains only complete frames (>1) */
-+#define MMAL_BUFFER_HEADER_FLAG_FRAME \
-+ (MMAL_BUFFER_HEADER_FLAG_FRAME_START|MMAL_BUFFER_HEADER_FLAG_FRAME_END)
-+/** Signals that the current payload is a keyframe (i.e. self decodable) */
-+#define MMAL_BUFFER_HEADER_FLAG_KEYFRAME (1<<3)
-+/** Signals a discontinuity in the stream of data (e.g. after a seek).
-+ * Can be used for instance by a decoder to reset its state */
-+#define MMAL_BUFFER_HEADER_FLAG_DISCONTINUITY (1<<4)
-+/** Signals a buffer containing some kind of config data for the component
-+ * (e.g. codec config data) */
-+#define MMAL_BUFFER_HEADER_FLAG_CONFIG (1<<5)
-+/** Signals an encrypted payload */
-+#define MMAL_BUFFER_HEADER_FLAG_ENCRYPTED (1<<6)
-+/** Signals a buffer containing side information */
-+#define MMAL_BUFFER_HEADER_FLAG_CODECSIDEINFO (1<<7)
-+/** Signals a buffer which is the snapshot/postview image from a stills
-+ * capture
-+ */
-+#define MMAL_BUFFER_HEADER_FLAGS_SNAPSHOT (1<<8)
-+/** Signals a buffer which contains data known to be corrupted */
-+#define MMAL_BUFFER_HEADER_FLAG_CORRUPTED (1<<9)
-+/** Signals that a buffer failed to be transmitted */
-+#define MMAL_BUFFER_HEADER_FLAG_TRANSMISSION_FAILED (1<<10)
-+
-+struct mmal_driver_buffer {
-+ u32 magic;
-+ u32 component_handle;
-+ u32 port_handle;
-+ void *client_context;
-+};
-+
-+/* buffer header */
-+struct mmal_buffer_header {
-+ struct mmal_buffer_header *next; /* next header */
-+ void *priv; /* framework private data */
-+ u32 cmd;
-+ void *data;
-+ u32 alloc_size;
-+ u32 length;
-+ u32 offset;
-+ u32 flags;
-+ s64 pts;
-+ s64 dts;
-+ void *type;
-+ void *user_data;
-+};
-+
-+struct mmal_buffer_header_type_specific {
-+ union {
-+ struct {
-+ u32 planes;
-+ u32 offset[4];
-+ u32 pitch[4];
-+ u32 flags;
-+ } video;
-+ } u;
-+};
-+
-+struct mmal_msg_buffer_from_host {
-+ /* The front 32 bytes of the buffer header are copied
-+ * back to us in the reply to allow for context. This
-+ * area is used to store two mmal_driver_buffer structures to
-+ * allow for multiple concurrent service users.
-+ */
-+ /* control data */
-+ struct mmal_driver_buffer drvbuf;
-+
-+ /* referenced control data for passthrough buffer management */
-+ struct mmal_driver_buffer drvbuf_ref;
-+ struct mmal_buffer_header buffer_header; /* buffer header itself */
-+ struct mmal_buffer_header_type_specific buffer_header_type_specific;
-+ s32 is_zero_copy;
-+ s32 has_reference;
-+
-+ /** allows short data to be xfered in control message */
-+ u32 payload_in_message;
-+ u8 short_data[MMAL_VC_SHORT_DATA];
-+};
-+
-+
-+/* port parameter setting */
-+
-+#define MMAL_WORKER_PORT_PARAMETER_SPACE 96
-+
-+struct mmal_msg_port_parameter_set {
-+ u32 component_handle; /* component */
-+ u32 port_handle; /* port */
-+ u32 id; /* Parameter ID */
-+ u32 size; /* Parameter size */
-+ uint32_t value[MMAL_WORKER_PORT_PARAMETER_SPACE];
-+};
-+
-+struct mmal_msg_port_parameter_set_reply {
-+ u32 status; /** enum mmal_msg_status todo: how does this
-+ * differ to the one in the header?
-+ */
-+};
-+
-+/* port parameter getting */
-+
-+struct mmal_msg_port_parameter_get {
-+ u32 component_handle; /* component */
-+ u32 port_handle; /* port */
-+ u32 id; /* Parameter ID */
-+ u32 size; /* Parameter size */
-+};
-+
-+struct mmal_msg_port_parameter_get_reply {
-+ u32 status; /* Status of mmal_port_parameter_get call */
-+ u32 id; /* Parameter ID */
-+ u32 size; /* Parameter size */
-+ uint32_t value[MMAL_WORKER_PORT_PARAMETER_SPACE];
-+};
-+
-+/* event messages */
-+#define MMAL_WORKER_EVENT_SPACE 256
-+
-+struct mmal_msg_event_to_host {
-+ void *client_component; /* component context */
-+
-+ u32 port_type;
-+ u32 port_num;
-+
-+ u32 cmd;
-+ u32 length;
-+ u8 data[MMAL_WORKER_EVENT_SPACE];
-+ struct mmal_buffer_header *delayed_buffer;
-+};
-+
-+/* all mmal messages are serialised through this structure */
-+struct mmal_msg {
-+ /* header */
-+ struct mmal_msg_header h;
-+ /* payload */
-+ union {
-+ struct mmal_msg_version version;
-+
-+ struct mmal_msg_component_create component_create;
-+ struct mmal_msg_component_create_reply component_create_reply;
-+
-+ struct mmal_msg_component_destroy component_destroy;
-+ struct mmal_msg_component_destroy_reply component_destroy_reply;
-+
-+ struct mmal_msg_component_enable component_enable;
-+ struct mmal_msg_component_enable_reply component_enable_reply;
-+
-+ struct mmal_msg_component_disable component_disable;
-+ struct mmal_msg_component_disable_reply component_disable_reply;
-+
-+ struct mmal_msg_port_info_get port_info_get;
-+ struct mmal_msg_port_info_get_reply port_info_get_reply;
-+
-+ struct mmal_msg_port_info_set port_info_set;
-+ struct mmal_msg_port_info_set_reply port_info_set_reply;
-+
-+ struct mmal_msg_port_action_port port_action_port;
-+ struct mmal_msg_port_action_handle port_action_handle;
-+ struct mmal_msg_port_action_reply port_action_reply;
-+
-+ struct mmal_msg_buffer_from_host buffer_from_host;
-+
-+ struct mmal_msg_port_parameter_set port_parameter_set;
-+ struct mmal_msg_port_parameter_set_reply
-+ port_parameter_set_reply;
-+ struct mmal_msg_port_parameter_get
-+ port_parameter_get;
-+ struct mmal_msg_port_parameter_get_reply
-+ port_parameter_get_reply;
-+
-+ struct mmal_msg_event_to_host event_to_host;
-+
-+ u8 payload[MMAL_MSG_MAX_PAYLOAD];
-+ } u;
-+};
---- /dev/null
-+++ b/drivers/media/platform/bcm2835/mmal-parameters.h
-@@ -0,0 +1,656 @@
-+/*
-+ * Broadcom BM2835 V4L2 driver
-+ *
-+ * Copyright © 2013 Raspberry Pi (Trading) Ltd.
-+ *
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License. See the file COPYING in the main directory of this archive
-+ * for more details.
-+ *
-+ * Authors: Vincent Sanders <vincent.sanders at collabora.co.uk>
-+ * Dave Stevenson <dsteve at broadcom.com>
-+ * Simon Mellor <simellor at broadcom.com>
-+ * Luke Diamand <luked at broadcom.com>
-+ */
-+
-+/* common parameters */
-+
-+/** @name Parameter groups
-+ * Parameters are divided into groups, and then allocated sequentially within
-+ * a group using an enum.
-+ * @{
-+ */
-+
-+/** Common parameter ID group, used with many types of component. */
-+#define MMAL_PARAMETER_GROUP_COMMON (0<<16)
-+/** Camera-specific parameter ID group. */
-+#define MMAL_PARAMETER_GROUP_CAMERA (1<<16)
-+/** Video-specific parameter ID group. */
-+#define MMAL_PARAMETER_GROUP_VIDEO (2<<16)
-+/** Audio-specific parameter ID group. */
-+#define MMAL_PARAMETER_GROUP_AUDIO (3<<16)
-+/** Clock-specific parameter ID group. */
-+#define MMAL_PARAMETER_GROUP_CLOCK (4<<16)
-+/** Miracast-specific parameter ID group. */
-+#define MMAL_PARAMETER_GROUP_MIRACAST (5<<16)
-+
-+/* Common parameters */
-+enum mmal_parameter_common_type {
-+ MMAL_PARAMETER_UNUSED /**< Never a valid parameter ID */
-+ = MMAL_PARAMETER_GROUP_COMMON,
-+ MMAL_PARAMETER_SUPPORTED_ENCODINGS, /**< MMAL_PARAMETER_ENCODING_T */
-+ MMAL_PARAMETER_URI, /**< MMAL_PARAMETER_URI_T */
-+
-+ /** MMAL_PARAMETER_CHANGE_EVENT_REQUEST_T */
-+ MMAL_PARAMETER_CHANGE_EVENT_REQUEST,
-+
-+ /** MMAL_PARAMETER_BOOLEAN_T */
-+ MMAL_PARAMETER_ZERO_COPY,
-+
-+ /**< MMAL_PARAMETER_BUFFER_REQUIREMENTS_T */
-+ MMAL_PARAMETER_BUFFER_REQUIREMENTS,
-+
-+ MMAL_PARAMETER_STATISTICS, /**< MMAL_PARAMETER_STATISTICS_T */
-+ MMAL_PARAMETER_CORE_STATISTICS, /**< MMAL_PARAMETER_CORE_STATISTICS_T */
-+ MMAL_PARAMETER_MEM_USAGE, /**< MMAL_PARAMETER_MEM_USAGE_T */
-+ MMAL_PARAMETER_BUFFER_FLAG_FILTER, /**< MMAL_PARAMETER_UINT32_T */
-+ MMAL_PARAMETER_SEEK, /**< MMAL_PARAMETER_SEEK_T */
-+ MMAL_PARAMETER_POWERMON_ENABLE, /**< MMAL_PARAMETER_BOOLEAN_T */
-+ MMAL_PARAMETER_LOGGING, /**< MMAL_PARAMETER_LOGGING_T */
-+ MMAL_PARAMETER_SYSTEM_TIME, /**< MMAL_PARAMETER_UINT64_T */
-+ MMAL_PARAMETER_NO_IMAGE_PADDING /**< MMAL_PARAMETER_BOOLEAN_T */
-+};
-+
-+/* camera parameters */
-+
-+enum mmal_parameter_camera_type {
-+ /* 0 */
-+ /** @ref MMAL_PARAMETER_THUMBNAIL_CONFIG_T */
-+ MMAL_PARAMETER_THUMBNAIL_CONFIGURATION
-+ = MMAL_PARAMETER_GROUP_CAMERA,
-+ MMAL_PARAMETER_CAPTURE_QUALITY, /**< Unused? */
-+ MMAL_PARAMETER_ROTATION, /**< @ref MMAL_PARAMETER_INT32_T */
-+ MMAL_PARAMETER_EXIF_DISABLE, /**< @ref MMAL_PARAMETER_BOOLEAN_T */
-+ MMAL_PARAMETER_EXIF, /**< @ref MMAL_PARAMETER_EXIF_T */
-+ MMAL_PARAMETER_AWB_MODE, /**< @ref MMAL_PARAM_AWBMODE_T */
-+ MMAL_PARAMETER_IMAGE_EFFECT, /**< @ref MMAL_PARAMETER_IMAGEFX_T */
-+ MMAL_PARAMETER_COLOUR_EFFECT, /**< @ref MMAL_PARAMETER_COLOURFX_T */
-+ MMAL_PARAMETER_FLICKER_AVOID, /**< @ref MMAL_PARAMETER_FLICKERAVOID_T */
-+ MMAL_PARAMETER_FLASH, /**< @ref MMAL_PARAMETER_FLASH_T */
-+ MMAL_PARAMETER_REDEYE, /**< @ref MMAL_PARAMETER_REDEYE_T */
-+ MMAL_PARAMETER_FOCUS, /**< @ref MMAL_PARAMETER_FOCUS_T */
-+ MMAL_PARAMETER_FOCAL_LENGTHS, /**< Unused? */
-+ MMAL_PARAMETER_EXPOSURE_COMP, /**< @ref MMAL_PARAMETER_INT32_T */
-+ MMAL_PARAMETER_ZOOM, /**< @ref MMAL_PARAMETER_SCALEFACTOR_T */
-+ MMAL_PARAMETER_MIRROR, /**< @ref MMAL_PARAMETER_MIRROR_T */
-+
-+ /* 0x10 */
-+ MMAL_PARAMETER_CAMERA_NUM, /**< @ref MMAL_PARAMETER_UINT32_T */
-+ MMAL_PARAMETER_CAPTURE, /**< @ref MMAL_PARAMETER_BOOLEAN_T */
-+ MMAL_PARAMETER_EXPOSURE_MODE, /**< @ref MMAL_PARAMETER_EXPOSUREMODE_T */
-+ MMAL_PARAMETER_EXP_METERING_MODE, /**< @ref MMAL_PARAMETER_EXPOSUREMETERINGMODE_T */
-+ MMAL_PARAMETER_FOCUS_STATUS, /**< @ref MMAL_PARAMETER_FOCUS_STATUS_T */
-+ MMAL_PARAMETER_CAMERA_CONFIG, /**< @ref MMAL_PARAMETER_CAMERA_CONFIG_T */
-+ MMAL_PARAMETER_CAPTURE_STATUS, /**< @ref MMAL_PARAMETER_CAPTURE_STATUS_T */
-+ MMAL_PARAMETER_FACE_TRACK, /**< @ref MMAL_PARAMETER_FACE_TRACK_T */
-+ MMAL_PARAMETER_DRAW_BOX_FACES_AND_FOCUS, /**< @ref MMAL_PARAMETER_BOOLEAN_T */
-+ MMAL_PARAMETER_JPEG_Q_FACTOR, /**< @ref MMAL_PARAMETER_UINT32_T */
-+ MMAL_PARAMETER_FRAME_RATE, /**< @ref MMAL_PARAMETER_FRAME_RATE_T */
-+ MMAL_PARAMETER_USE_STC, /**< @ref MMAL_PARAMETER_CAMERA_STC_MODE_T */
-+ MMAL_PARAMETER_CAMERA_INFO, /**< @ref MMAL_PARAMETER_CAMERA_INFO_T */
-+ MMAL_PARAMETER_VIDEO_STABILISATION, /**< @ref MMAL_PARAMETER_BOOLEAN_T */
-+ MMAL_PARAMETER_FACE_TRACK_RESULTS, /**< @ref MMAL_PARAMETER_FACE_TRACK_RESULTS_T */
-+ MMAL_PARAMETER_ENABLE_RAW_CAPTURE, /**< @ref MMAL_PARAMETER_BOOLEAN_T */
-+
-+ /* 0x20 */
-+ MMAL_PARAMETER_DPF_FILE, /**< @ref MMAL_PARAMETER_URI_T */
-+ MMAL_PARAMETER_ENABLE_DPF_FILE, /**< @ref MMAL_PARAMETER_BOOLEAN_T */
-+ MMAL_PARAMETER_DPF_FAIL_IS_FATAL, /**< @ref MMAL_PARAMETER_BOOLEAN_T */
-+ MMAL_PARAMETER_CAPTURE_MODE, /**< @ref MMAL_PARAMETER_CAPTUREMODE_T */
-+ MMAL_PARAMETER_FOCUS_REGIONS, /**< @ref MMAL_PARAMETER_FOCUS_REGIONS_T */
-+ MMAL_PARAMETER_INPUT_CROP, /**< @ref MMAL_PARAMETER_INPUT_CROP_T */
-+ MMAL_PARAMETER_SENSOR_INFORMATION, /**< @ref MMAL_PARAMETER_SENSOR_INFORMATION_T */
-+ MMAL_PARAMETER_FLASH_SELECT, /**< @ref MMAL_PARAMETER_FLASH_SELECT_T */
-+ MMAL_PARAMETER_FIELD_OF_VIEW, /**< @ref MMAL_PARAMETER_FIELD_OF_VIEW_T */
-+ MMAL_PARAMETER_HIGH_DYNAMIC_RANGE, /**< @ref MMAL_PARAMETER_BOOLEAN_T */
-+ MMAL_PARAMETER_DYNAMIC_RANGE_COMPRESSION, /**< @ref MMAL_PARAMETER_DRC_T */
-+ MMAL_PARAMETER_ALGORITHM_CONTROL, /**< @ref MMAL_PARAMETER_ALGORITHM_CONTROL_T */
-+ MMAL_PARAMETER_SHARPNESS, /**< @ref MMAL_PARAMETER_RATIONAL_T */
-+ MMAL_PARAMETER_CONTRAST, /**< @ref MMAL_PARAMETER_RATIONAL_T */
-+ MMAL_PARAMETER_BRIGHTNESS, /**< @ref MMAL_PARAMETER_RATIONAL_T */
-+ MMAL_PARAMETER_SATURATION, /**< @ref MMAL_PARAMETER_RATIONAL_T */
-+
-+ /* 0x30 */
-+ MMAL_PARAMETER_ISO, /**< @ref MMAL_PARAMETER_UINT32_T */
-+ MMAL_PARAMETER_ANTISHAKE, /**< @ref MMAL_PARAMETER_BOOLEAN_T */
-+
-+ /** @ref MMAL_PARAMETER_IMAGEFX_PARAMETERS_T */
-+ MMAL_PARAMETER_IMAGE_EFFECT_PARAMETERS,
-+
-+ /** @ref MMAL_PARAMETER_BOOLEAN_T */
-+ MMAL_PARAMETER_CAMERA_BURST_CAPTURE,
-+
-+ /** @ref MMAL_PARAMETER_UINT32_T */
-+ MMAL_PARAMETER_CAMERA_MIN_ISO,
-+
-+ /** @ref MMAL_PARAMETER_CAMERA_USE_CASE_T */
-+ MMAL_PARAMETER_CAMERA_USE_CASE,
-+
-+ /**< @ref MMAL_PARAMETER_BOOLEAN_T */
-+ MMAL_PARAMETER_CAPTURE_STATS_PASS,
-+
-+ /** @ref MMAL_PARAMETER_UINT32_T */
-+ MMAL_PARAMETER_CAMERA_CUSTOM_SENSOR_CONFIG,
-+
-+ /** @ref MMAL_PARAMETER_BOOLEAN_T */
-+ MMAL_PARAMETER_ENABLE_REGISTER_FILE,
-+
-+ /** @ref MMAL_PARAMETER_BOOLEAN_T */
-+ MMAL_PARAMETER_REGISTER_FAIL_IS_FATAL,
-+
-+ /** @ref MMAL_PARAMETER_CONFIGFILE_T */
-+ MMAL_PARAMETER_CONFIGFILE_REGISTERS,
-+
-+ /** @ref MMAL_PARAMETER_CONFIGFILE_CHUNK_T */
-+ MMAL_PARAMETER_CONFIGFILE_CHUNK_REGISTERS,
-+ MMAL_PARAMETER_JPEG_ATTACH_LOG, /**< @ref MMAL_PARAMETER_BOOLEAN_T */
-+ MMAL_PARAMETER_ZERO_SHUTTER_LAG, /**< @ref MMAL_PARAMETER_ZEROSHUTTERLAG_T */
-+ MMAL_PARAMETER_FPS_RANGE, /**< @ref MMAL_PARAMETER_FPS_RANGE_T */
-+ MMAL_PARAMETER_CAPTURE_EXPOSURE_COMP, /**< @ref MMAL_PARAMETER_INT32_T */
-+
-+ /* 0x40 */
-+ MMAL_PARAMETER_SW_SHARPEN_DISABLE, /**< @ref MMAL_PARAMETER_BOOLEAN_T */
-+ MMAL_PARAMETER_FLASH_REQUIRED, /**< @ref MMAL_PARAMETER_BOOLEAN_T */
-+ MMAL_PARAMETER_SW_SATURATION_DISABLE, /**< @ref MMAL_PARAMETER_BOOLEAN_T */
-+ MMAL_PARAMETER_SHUTTER_SPEED, /**< Takes a @ref MMAL_PARAMETER_UINT32_T */
-+ MMAL_PARAMETER_CUSTOM_AWB_GAINS, /**< Takes a @ref MMAL_PARAMETER_AWB_GAINS_T */
-+};
-+
-+struct mmal_parameter_rational {
-+ s32 num; /**< Numerator */
-+ s32 den; /**< Denominator */
-+};
-+
-+enum mmal_parameter_camera_config_timestamp_mode {
-+ MMAL_PARAM_TIMESTAMP_MODE_ZERO = 0, /* Always timestamp frames as 0 */
-+ MMAL_PARAM_TIMESTAMP_MODE_RAW_STC, /* Use the raw STC value
-+ * for the frame timestamp
-+ */
-+ MMAL_PARAM_TIMESTAMP_MODE_RESET_STC, /* Use the STC timestamp
-+ * but subtract the
-+ * timestamp of the first
-+ * frame sent to give a
-+ * zero based timestamp.
-+ */
-+};
-+
-+struct mmal_parameter_fps_range {
-+ /**< Low end of the permitted framerate range */
-+ struct mmal_parameter_rational fps_low;
-+ /**< High end of the permitted framerate range */
-+ struct mmal_parameter_rational fps_high;
-+};
-+
-+
-+/* camera configuration parameter */
-+struct mmal_parameter_camera_config {
-+ /* Parameters for setting up the image pools */
-+ u32 max_stills_w; /* Max size of stills capture */
-+ u32 max_stills_h;
-+ u32 stills_yuv422; /* Allow YUV422 stills capture */
-+ u32 one_shot_stills; /* Continuous or one shot stills captures. */
-+
-+ u32 max_preview_video_w; /* Max size of the preview or video
-+ * capture frames
-+ */
-+ u32 max_preview_video_h;
-+ u32 num_preview_video_frames;
-+
-+ /** Sets the height of the circular buffer for stills capture. */
-+ u32 stills_capture_circular_buffer_height;
-+
-+ /** Allows preview/encode to resume as fast as possible after the stills
-+ * input frame has been received, and then processes the still frame in
-+ * the background whilst preview/encode has resumed.
-+ * Actual mode is controlled by MMAL_PARAMETER_CAPTURE_MODE.
-+ */
-+ u32 fast_preview_resume;
-+
-+ /** Selects algorithm for timestamping frames if
-+ * there is no clock component connected.
-+ * enum mmal_parameter_camera_config_timestamp_mode
-+ */
-+ s32 use_stc_timestamp;
-+};
-+
-+
-+enum mmal_parameter_exposuremode {
-+ MMAL_PARAM_EXPOSUREMODE_OFF,
-+ MMAL_PARAM_EXPOSUREMODE_AUTO,
-+ MMAL_PARAM_EXPOSUREMODE_NIGHT,
-+ MMAL_PARAM_EXPOSUREMODE_NIGHTPREVIEW,
-+ MMAL_PARAM_EXPOSUREMODE_BACKLIGHT,
-+ MMAL_PARAM_EXPOSUREMODE_SPOTLIGHT,
-+ MMAL_PARAM_EXPOSUREMODE_SPORTS,
-+ MMAL_PARAM_EXPOSUREMODE_SNOW,
-+ MMAL_PARAM_EXPOSUREMODE_BEACH,
-+ MMAL_PARAM_EXPOSUREMODE_VERYLONG,
-+ MMAL_PARAM_EXPOSUREMODE_FIXEDFPS,
-+ MMAL_PARAM_EXPOSUREMODE_ANTISHAKE,
-+ MMAL_PARAM_EXPOSUREMODE_FIREWORKS,
-+};
-+
-+enum mmal_parameter_exposuremeteringmode {
-+ MMAL_PARAM_EXPOSUREMETERINGMODE_AVERAGE,
-+ MMAL_PARAM_EXPOSUREMETERINGMODE_SPOT,
-+ MMAL_PARAM_EXPOSUREMETERINGMODE_BACKLIT,
-+ MMAL_PARAM_EXPOSUREMETERINGMODE_MATRIX,
-+};
-+
-+enum mmal_parameter_awbmode {
-+ MMAL_PARAM_AWBMODE_OFF,
-+ MMAL_PARAM_AWBMODE_AUTO,
-+ MMAL_PARAM_AWBMODE_SUNLIGHT,
-+ MMAL_PARAM_AWBMODE_CLOUDY,
-+ MMAL_PARAM_AWBMODE_SHADE,
-+ MMAL_PARAM_AWBMODE_TUNGSTEN,
-+ MMAL_PARAM_AWBMODE_FLUORESCENT,
-+ MMAL_PARAM_AWBMODE_INCANDESCENT,
-+ MMAL_PARAM_AWBMODE_FLASH,
-+ MMAL_PARAM_AWBMODE_HORIZON,
-+};
-+
-+enum mmal_parameter_imagefx {
-+ MMAL_PARAM_IMAGEFX_NONE,
-+ MMAL_PARAM_IMAGEFX_NEGATIVE,
-+ MMAL_PARAM_IMAGEFX_SOLARIZE,
-+ MMAL_PARAM_IMAGEFX_POSTERIZE,
-+ MMAL_PARAM_IMAGEFX_WHITEBOARD,
-+ MMAL_PARAM_IMAGEFX_BLACKBOARD,
-+ MMAL_PARAM_IMAGEFX_SKETCH,
-+ MMAL_PARAM_IMAGEFX_DENOISE,
-+ MMAL_PARAM_IMAGEFX_EMBOSS,
-+ MMAL_PARAM_IMAGEFX_OILPAINT,
-+ MMAL_PARAM_IMAGEFX_HATCH,
-+ MMAL_PARAM_IMAGEFX_GPEN,
-+ MMAL_PARAM_IMAGEFX_PASTEL,
-+ MMAL_PARAM_IMAGEFX_WATERCOLOUR,
-+ MMAL_PARAM_IMAGEFX_FILM,
-+ MMAL_PARAM_IMAGEFX_BLUR,
-+ MMAL_PARAM_IMAGEFX_SATURATION,
-+ MMAL_PARAM_IMAGEFX_COLOURSWAP,
-+ MMAL_PARAM_IMAGEFX_WASHEDOUT,
-+ MMAL_PARAM_IMAGEFX_POSTERISE,
-+ MMAL_PARAM_IMAGEFX_COLOURPOINT,
-+ MMAL_PARAM_IMAGEFX_COLOURBALANCE,
-+ MMAL_PARAM_IMAGEFX_CARTOON,
-+};
-+
-+enum MMAL_PARAM_FLICKERAVOID_T {
-+ MMAL_PARAM_FLICKERAVOID_OFF,
-+ MMAL_PARAM_FLICKERAVOID_AUTO,
-+ MMAL_PARAM_FLICKERAVOID_50HZ,
-+ MMAL_PARAM_FLICKERAVOID_60HZ,
-+ MMAL_PARAM_FLICKERAVOID_MAX = 0x7FFFFFFF
-+};
-+
-+struct mmal_parameter_awbgains {
-+ struct mmal_parameter_rational r_gain; /**< Red gain */
-+ struct mmal_parameter_rational b_gain; /**< Blue gain */
-+};
-+
-+/** Manner of video rate control */
-+enum mmal_parameter_rate_control_mode {
-+ MMAL_VIDEO_RATECONTROL_DEFAULT,
-+ MMAL_VIDEO_RATECONTROL_VARIABLE,
-+ MMAL_VIDEO_RATECONTROL_CONSTANT,
-+ MMAL_VIDEO_RATECONTROL_VARIABLE_SKIP_FRAMES,
-+ MMAL_VIDEO_RATECONTROL_CONSTANT_SKIP_FRAMES
-+};
-+
-+enum mmal_video_profile {
-+ MMAL_VIDEO_PROFILE_H263_BASELINE,
-+ MMAL_VIDEO_PROFILE_H263_H320CODING,
-+ MMAL_VIDEO_PROFILE_H263_BACKWARDCOMPATIBLE,
-+ MMAL_VIDEO_PROFILE_H263_ISWV2,
-+ MMAL_VIDEO_PROFILE_H263_ISWV3,
-+ MMAL_VIDEO_PROFILE_H263_HIGHCOMPRESSION,
-+ MMAL_VIDEO_PROFILE_H263_INTERNET,
-+ MMAL_VIDEO_PROFILE_H263_INTERLACE,
-+ MMAL_VIDEO_PROFILE_H263_HIGHLATENCY,
-+ MMAL_VIDEO_PROFILE_MP4V_SIMPLE,
-+ MMAL_VIDEO_PROFILE_MP4V_SIMPLESCALABLE,
-+ MMAL_VIDEO_PROFILE_MP4V_CORE,
-+ MMAL_VIDEO_PROFILE_MP4V_MAIN,
-+ MMAL_VIDEO_PROFILE_MP4V_NBIT,
-+ MMAL_VIDEO_PROFILE_MP4V_SCALABLETEXTURE,
-+ MMAL_VIDEO_PROFILE_MP4V_SIMPLEFACE,
-+ MMAL_VIDEO_PROFILE_MP4V_SIMPLEFBA,
-+ MMAL_VIDEO_PROFILE_MP4V_BASICANIMATED,
-+ MMAL_VIDEO_PROFILE_MP4V_HYBRID,
-+ MMAL_VIDEO_PROFILE_MP4V_ADVANCEDREALTIME,
-+ MMAL_VIDEO_PROFILE_MP4V_CORESCALABLE,
-+ MMAL_VIDEO_PROFILE_MP4V_ADVANCEDCODING,
-+ MMAL_VIDEO_PROFILE_MP4V_ADVANCEDCORE,
-+ MMAL_VIDEO_PROFILE_MP4V_ADVANCEDSCALABLE,
-+ MMAL_VIDEO_PROFILE_MP4V_ADVANCEDSIMPLE,
-+ MMAL_VIDEO_PROFILE_H264_BASELINE,
-+ MMAL_VIDEO_PROFILE_H264_MAIN,
-+ MMAL_VIDEO_PROFILE_H264_EXTENDED,
-+ MMAL_VIDEO_PROFILE_H264_HIGH,
-+ MMAL_VIDEO_PROFILE_H264_HIGH10,
-+ MMAL_VIDEO_PROFILE_H264_HIGH422,
-+ MMAL_VIDEO_PROFILE_H264_HIGH444,
-+ MMAL_VIDEO_PROFILE_H264_CONSTRAINED_BASELINE,
-+ MMAL_VIDEO_PROFILE_DUMMY = 0x7FFFFFFF
-+};
-+
-+enum mmal_video_level {
-+ MMAL_VIDEO_LEVEL_H263_10,
-+ MMAL_VIDEO_LEVEL_H263_20,
-+ MMAL_VIDEO_LEVEL_H263_30,
-+ MMAL_VIDEO_LEVEL_H263_40,
-+ MMAL_VIDEO_LEVEL_H263_45,
-+ MMAL_VIDEO_LEVEL_H263_50,
-+ MMAL_VIDEO_LEVEL_H263_60,
-+ MMAL_VIDEO_LEVEL_H263_70,
-+ MMAL_VIDEO_LEVEL_MP4V_0,
-+ MMAL_VIDEO_LEVEL_MP4V_0b,
-+ MMAL_VIDEO_LEVEL_MP4V_1,
-+ MMAL_VIDEO_LEVEL_MP4V_2,
-+ MMAL_VIDEO_LEVEL_MP4V_3,
-+ MMAL_VIDEO_LEVEL_MP4V_4,
-+ MMAL_VIDEO_LEVEL_MP4V_4a,
-+ MMAL_VIDEO_LEVEL_MP4V_5,
-+ MMAL_VIDEO_LEVEL_MP4V_6,
-+ MMAL_VIDEO_LEVEL_H264_1,
-+ MMAL_VIDEO_LEVEL_H264_1b,
-+ MMAL_VIDEO_LEVEL_H264_11,
-+ MMAL_VIDEO_LEVEL_H264_12,
-+ MMAL_VIDEO_LEVEL_H264_13,
-+ MMAL_VIDEO_LEVEL_H264_2,
-+ MMAL_VIDEO_LEVEL_H264_21,
-+ MMAL_VIDEO_LEVEL_H264_22,
-+ MMAL_VIDEO_LEVEL_H264_3,
-+ MMAL_VIDEO_LEVEL_H264_31,
-+ MMAL_VIDEO_LEVEL_H264_32,
-+ MMAL_VIDEO_LEVEL_H264_4,
-+ MMAL_VIDEO_LEVEL_H264_41,
-+ MMAL_VIDEO_LEVEL_H264_42,
-+ MMAL_VIDEO_LEVEL_H264_5,
-+ MMAL_VIDEO_LEVEL_H264_51,
-+ MMAL_VIDEO_LEVEL_DUMMY = 0x7FFFFFFF
-+};
-+
-+struct mmal_parameter_video_profile {
-+ enum mmal_video_profile profile;
-+ enum mmal_video_level level;
-+};
-+
-+/* video parameters */
-+
-+enum mmal_parameter_video_type {
-+ /** @ref MMAL_DISPLAYREGION_T */
-+ MMAL_PARAMETER_DISPLAYREGION = MMAL_PARAMETER_GROUP_VIDEO,
-+
-+ /** @ref MMAL_PARAMETER_VIDEO_PROFILE_T */
-+ MMAL_PARAMETER_SUPPORTED_PROFILES,
-+
-+ /** @ref MMAL_PARAMETER_VIDEO_PROFILE_T */
-+ MMAL_PARAMETER_PROFILE,
-+
-+ /** @ref MMAL_PARAMETER_UINT32_T */
-+ MMAL_PARAMETER_INTRAPERIOD,
-+
-+ /** @ref MMAL_PARAMETER_VIDEO_RATECONTROL_T */
-+ MMAL_PARAMETER_RATECONTROL,
-+
-+ /** @ref MMAL_PARAMETER_VIDEO_NALUNITFORMAT_T */
-+ MMAL_PARAMETER_NALUNITFORMAT,
-+
-+ /** @ref MMAL_PARAMETER_BOOLEAN_T */
-+ MMAL_PARAMETER_MINIMISE_FRAGMENTATION,
-+
-+ /** @ref MMAL_PARAMETER_UINT32_T.
-+ * Setting the value to zero resets to the default (one slice per frame).
-+ */
-+ MMAL_PARAMETER_MB_ROWS_PER_SLICE,
-+
-+ /** @ref MMAL_PARAMETER_VIDEO_LEVEL_EXTENSION_T */
-+ MMAL_PARAMETER_VIDEO_LEVEL_EXTENSION,
-+
-+ /** @ref MMAL_PARAMETER_VIDEO_EEDE_ENABLE_T */
-+ MMAL_PARAMETER_VIDEO_EEDE_ENABLE,
-+
-+ /** @ref MMAL_PARAMETER_VIDEO_EEDE_LOSSRATE_T */
-+ MMAL_PARAMETER_VIDEO_EEDE_LOSSRATE,
-+
-+ /** @ref MMAL_PARAMETER_BOOLEAN_T. Request an I-frame. */
-+ MMAL_PARAMETER_VIDEO_REQUEST_I_FRAME,
-+ /** @ref MMAL_PARAMETER_VIDEO_INTRA_REFRESH_T */
-+ MMAL_PARAMETER_VIDEO_INTRA_REFRESH,
-+
-+ /** @ref MMAL_PARAMETER_BOOLEAN_T. */
-+ MMAL_PARAMETER_VIDEO_IMMUTABLE_INPUT,
-+
-+ /** @ref MMAL_PARAMETER_UINT32_T. Run-time bit rate control */
-+ MMAL_PARAMETER_VIDEO_BIT_RATE,
-+
-+ /** @ref MMAL_PARAMETER_FRAME_RATE_T */
-+ MMAL_PARAMETER_VIDEO_FRAME_RATE,
-+
-+ /** @ref MMAL_PARAMETER_UINT32_T. */
-+ MMAL_PARAMETER_VIDEO_ENCODE_MIN_QUANT,
-+
-+ /** @ref MMAL_PARAMETER_UINT32_T. */
-+ MMAL_PARAMETER_VIDEO_ENCODE_MAX_QUANT,
-+
-+ /** @ref MMAL_PARAMETER_VIDEO_ENCODE_RC_MODEL_T. */
-+ MMAL_PARAMETER_VIDEO_ENCODE_RC_MODEL,
-+
-+ MMAL_PARAMETER_EXTRA_BUFFERS, /**< @ref MMAL_PARAMETER_UINT32_T. */
-+ /** @ref MMAL_PARAMETER_UINT32_T.
-+ * Changing this parameter from the default can reduce frame rate
-+ * because image buffers need to be re-pitched.
-+ */
-+ MMAL_PARAMETER_VIDEO_ALIGN_HORIZ,
-+
-+ /** @ref MMAL_PARAMETER_UINT32_T.
-+ * Changing this parameter from the default can reduce frame rate
-+ * because image buffers need to be re-pitched.
-+ */
-+ MMAL_PARAMETER_VIDEO_ALIGN_VERT,
-+
-+ /** @ref MMAL_PARAMETER_BOOLEAN_T. */
-+ MMAL_PARAMETER_VIDEO_DROPPABLE_PFRAMES,
-+
-+ /** @ref MMAL_PARAMETER_UINT32_T. */
-+ MMAL_PARAMETER_VIDEO_ENCODE_INITIAL_QUANT,
-+
-+ /**< @ref MMAL_PARAMETER_UINT32_T. */
-+ MMAL_PARAMETER_VIDEO_ENCODE_QP_P,
-+
-+ /**< @ref MMAL_PARAMETER_UINT32_T. */
-+ MMAL_PARAMETER_VIDEO_ENCODE_RC_SLICE_DQUANT,
-+
-+ /** @ref MMAL_PARAMETER_UINT32_T */
-+ MMAL_PARAMETER_VIDEO_ENCODE_FRAME_LIMIT_BITS,
-+
-+ /** @ref MMAL_PARAMETER_UINT32_T. */
-+ MMAL_PARAMETER_VIDEO_ENCODE_PEAK_RATE,
-+
-+ /* H264 specific parameters */
-+
-+ /** @ref MMAL_PARAMETER_BOOLEAN_T. */
-+ MMAL_PARAMETER_VIDEO_ENCODE_H264_DISABLE_CABAC,
-+
-+ /** @ref MMAL_PARAMETER_BOOLEAN_T. */
-+ MMAL_PARAMETER_VIDEO_ENCODE_H264_LOW_LATENCY,
-+
-+ /** @ref MMAL_PARAMETER_BOOLEAN_T. */
-+ MMAL_PARAMETER_VIDEO_ENCODE_H264_AU_DELIMITERS,
-+
-+ /** @ref MMAL_PARAMETER_UINT32_T. */
-+ MMAL_PARAMETER_VIDEO_ENCODE_H264_DEBLOCK_IDC,
-+
-+ /** @ref MMAL_PARAMETER_VIDEO_ENCODER_H264_MB_INTRA_MODES_T. */
-+ MMAL_PARAMETER_VIDEO_ENCODE_H264_MB_INTRA_MODE,
-+
-+ /** @ref MMAL_PARAMETER_BOOLEAN_T */
-+ MMAL_PARAMETER_VIDEO_ENCODE_HEADER_ON_OPEN,
-+
-+ /** @ref MMAL_PARAMETER_BOOLEAN_T */
-+ MMAL_PARAMETER_VIDEO_ENCODE_PRECODE_FOR_QP,
-+
-+ /** @ref MMAL_PARAMETER_VIDEO_DRM_INIT_INFO_T. */
-+ MMAL_PARAMETER_VIDEO_DRM_INIT_INFO,
-+
-+ /** @ref MMAL_PARAMETER_BOOLEAN_T */
-+ MMAL_PARAMETER_VIDEO_TIMESTAMP_FIFO,
-+
-+ /** @ref MMAL_PARAMETER_BOOLEAN_T */
-+ MMAL_PARAMETER_VIDEO_DECODE_ERROR_CONCEALMENT,
-+
-+ /** @ref MMAL_PARAMETER_VIDEO_DRM_PROTECT_BUFFER_T. */
-+ MMAL_PARAMETER_VIDEO_DRM_PROTECT_BUFFER,
-+
-+ /** @ref MMAL_PARAMETER_BYTES_T */
-+ MMAL_PARAMETER_VIDEO_DECODE_CONFIG_VD3,
-+
-+ /**< @ref MMAL_PARAMETER_BOOLEAN_T */
-+ MMAL_PARAMETER_VIDEO_ENCODE_H264_VCL_HRD_PARAMETERS,
-+
-+ /**< @ref MMAL_PARAMETER_BOOLEAN_T */
-+ MMAL_PARAMETER_VIDEO_ENCODE_H264_LOW_DELAY_HRD_FLAG,
-+
-+ /**< @ref MMAL_PARAMETER_BOOLEAN_T */
-+ MMAL_PARAMETER_VIDEO_ENCODE_INLINE_HEADER
-+};
-+
-+/** Valid mirror modes */
-+enum mmal_parameter_mirror {
-+ MMAL_PARAM_MIRROR_NONE,
-+ MMAL_PARAM_MIRROR_VERTICAL,
-+ MMAL_PARAM_MIRROR_HORIZONTAL,
-+ MMAL_PARAM_MIRROR_BOTH,
-+};
-+
-+enum mmal_parameter_displaytransform {
-+ MMAL_DISPLAY_ROT0 = 0,
-+ MMAL_DISPLAY_MIRROR_ROT0 = 1,
-+ MMAL_DISPLAY_MIRROR_ROT180 = 2,
-+ MMAL_DISPLAY_ROT180 = 3,
-+ MMAL_DISPLAY_MIRROR_ROT90 = 4,
-+ MMAL_DISPLAY_ROT270 = 5,
-+ MMAL_DISPLAY_ROT90 = 6,
-+ MMAL_DISPLAY_MIRROR_ROT270 = 7,
-+};
-+
-+enum mmal_parameter_displaymode {
-+ MMAL_DISPLAY_MODE_FILL = 0,
-+ MMAL_DISPLAY_MODE_LETTERBOX = 1,
-+};
-+
-+enum mmal_parameter_displayset {
-+ MMAL_DISPLAY_SET_NONE = 0,
-+ MMAL_DISPLAY_SET_NUM = 1,
-+ MMAL_DISPLAY_SET_FULLSCREEN = 2,
-+ MMAL_DISPLAY_SET_TRANSFORM = 4,
-+ MMAL_DISPLAY_SET_DEST_RECT = 8,
-+ MMAL_DISPLAY_SET_SRC_RECT = 0x10,
-+ MMAL_DISPLAY_SET_MODE = 0x20,
-+ MMAL_DISPLAY_SET_PIXEL = 0x40,
-+ MMAL_DISPLAY_SET_NOASPECT = 0x80,
-+ MMAL_DISPLAY_SET_LAYER = 0x100,
-+ MMAL_DISPLAY_SET_COPYPROTECT = 0x200,
-+ MMAL_DISPLAY_SET_ALPHA = 0x400,
-+};
-+
-+struct mmal_parameter_displayregion {
-+ /** Bitfield that indicates which fields are set and should be
-+ * used. All other fields will maintain their current value.
-+ * \ref MMAL_DISPLAYSET_T defines the bits that can be
-+ * combined.
-+ */
-+ u32 set;
-+
-+ /** Describes the display output device, with 0 typically
-+ * being a directly connected LCD display. The actual values
-+ * will depend on the hardware. Code using hard-wired numbers
-+ * (e.g. 2) is certain to fail.
-+ */
-+
-+ u32 display_num;
-+ /** Indicates that we are using the full device screen area,
-+ * rather than a window of the display. If zero, then
-+ * dest_rect is used to specify a region of the display to
-+ * use.
-+ */
-+
-+ s32 fullscreen;
-+ /** Indicates any rotation or flipping used to map frames onto
-+ * the natural display orientation.
-+ */
-+ u32 transform; /* enum mmal_parameter_displaytransform */
-+
-+ /** Where to display the frame within the screen, if
-+ * fullscreen is zero.
-+ */
-+ struct vchiq_mmal_rect dest_rect;
-+
-+ /** Indicates which area of the frame to display. If all
-+ * values are zero, the whole frame will be used.
-+ */
-+ struct vchiq_mmal_rect src_rect;
-+
-+ /** If set to non-zero, indicates that any display scaling
-+ * should disregard the aspect ratio of the frame region being
-+ * displayed.
-+ */
-+ s32 noaspect;
-+
-+ /** Indicates how the image should be scaled to fit the
-+ * display. \code MMAL_DISPLAY_MODE_FILL \endcode indicates
-+ * that the image should fill the screen by potentially
-+ * cropping the frames. Setting \code mode \endcode to \code
-+ * MMAL_DISPLAY_MODE_LETTERBOX \endcode indicates that all the
-+ * source region should be displayed and black bars added if
-+ * necessary.
-+ */
-+ u32 mode; /* enum mmal_parameter_displaymode */
-+
-+ /** If non-zero, defines the width of a source pixel relative
-+ * to \code pixel_y \endcode. If zero, then pixels default to
-+ * being square.
-+ */
-+ u32 pixel_x;
-+
-+ /** If non-zero, defines the height of a source pixel relative
-+ * to \code pixel_x \endcode. If zero, then pixels default to
-+ * being square.
-+ */
-+ u32 pixel_y;
-+
-+ /** Sets the relative depth of the images, with greater values
-+ * being in front of smaller values.
-+ */
-+ u32 layer;
-+
-+ /** Set to non-zero to ensure copy protection is used on
-+ * output.
-+ */
-+ s32 copyprotect_required;
-+
-+ /** Level of opacity of the layer, where zero is fully
-+ * transparent and 255 is fully opaque.
-+ */
-+ u32 alpha;
-+};
-+
-+#define MMAL_MAX_IMAGEFX_PARAMETERS 5
-+
-+struct mmal_parameter_imagefx_parameters {
-+ enum mmal_parameter_imagefx effect;
-+ u32 num_effect_params;
-+ u32 effect_parameter[MMAL_MAX_IMAGEFX_PARAMETERS];
-+};
---- /dev/null
-+++ b/drivers/media/platform/bcm2835/mmal-vchiq.c
-@@ -0,0 +1,1916 @@
-+/*
-+ * Broadcom BM2835 V4L2 driver
-+ *
-+ * Copyright © 2013 Raspberry Pi (Trading) Ltd.
-+ *
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License. See the file COPYING in the main directory of this archive
-+ * for more details.
-+ *
-+ * Authors: Vincent Sanders <vincent.sanders at collabora.co.uk>
-+ * Dave Stevenson <dsteve at broadcom.com>
-+ * Simon Mellor <simellor at broadcom.com>
-+ * Luke Diamand <luked at broadcom.com>
-+ *
-+ * V4L2 driver MMAL vchiq interface code
-+ */
-+
-+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
-+
-+#include <linux/errno.h>
-+#include <linux/kernel.h>
-+#include <linux/mutex.h>
-+#include <linux/mm.h>
-+#include <linux/slab.h>
-+#include <linux/completion.h>
-+#include <linux/vmalloc.h>
-+#include <asm/cacheflush.h>
-+#include <media/videobuf2-vmalloc.h>
-+
-+#include "mmal-common.h"
-+#include "mmal-vchiq.h"
-+#include "mmal-msg.h"
-+
-+#define USE_VCHIQ_ARM
-+#include "interface/vchi/vchi.h"
-+
-+/* maximum number of components supported */
-+#define VCHIQ_MMAL_MAX_COMPONENTS 4
-+
-+/*#define FULL_MSG_DUMP 1*/
-+
-+#ifdef DEBUG
-+static const char *const msg_type_names[] = {
-+ "UNKNOWN",
-+ "QUIT",
-+ "SERVICE_CLOSED",
-+ "GET_VERSION",
-+ "COMPONENT_CREATE",
-+ "COMPONENT_DESTROY",
-+ "COMPONENT_ENABLE",
-+ "COMPONENT_DISABLE",
-+ "PORT_INFO_GET",
-+ "PORT_INFO_SET",
-+ "PORT_ACTION",
-+ "BUFFER_FROM_HOST",
-+ "BUFFER_TO_HOST",
-+ "GET_STATS",
-+ "PORT_PARAMETER_SET",
-+ "PORT_PARAMETER_GET",
-+ "EVENT_TO_HOST",
-+ "GET_CORE_STATS_FOR_PORT",
-+ "OPAQUE_ALLOCATOR",
-+ "CONSUME_MEM",
-+ "LMK",
-+ "OPAQUE_ALLOCATOR_DESC",
-+ "DRM_GET_LHS32",
-+ "DRM_GET_TIME",
-+ "BUFFER_FROM_HOST_ZEROLEN",
-+ "PORT_FLUSH",
-+ "HOST_LOG",
-+};
-+#endif
-+
-+static const char *const port_action_type_names[] = {
-+ "UNKNOWN",
-+ "ENABLE",
-+ "DISABLE",
-+ "FLUSH",
-+ "CONNECT",
-+ "DISCONNECT",
-+ "SET_REQUIREMENTS",
-+};
-+
-+#if defined(DEBUG)
-+#if defined(FULL_MSG_DUMP)
-+#define DBG_DUMP_MSG(MSG, MSG_LEN, TITLE) \
-+ do { \
-+ pr_debug(TITLE" type:%s(%d) length:%d\n", \
-+ msg_type_names[(MSG)->h.type], \
-+ (MSG)->h.type, (MSG_LEN)); \
-+ print_hex_dump(KERN_DEBUG, "<<h: ", DUMP_PREFIX_OFFSET, \
-+ 16, 4, (MSG), \
-+ sizeof(struct mmal_msg_header), 1); \
-+ print_hex_dump(KERN_DEBUG, "<<p: ", DUMP_PREFIX_OFFSET, \
-+ 16, 4, \
-+ ((u8 *)(MSG)) + sizeof(struct mmal_msg_header),\
-+ (MSG_LEN) - sizeof(struct mmal_msg_header), 1); \
-+ } while (0)
-+#else
-+#define DBG_DUMP_MSG(MSG, MSG_LEN, TITLE) \
-+ { \
-+ pr_debug(TITLE" type:%s(%d) length:%d\n", \
-+ msg_type_names[(MSG)->h.type], \
-+ (MSG)->h.type, (MSG_LEN)); \
-+ }
-+#endif
-+#else
-+#define DBG_DUMP_MSG(MSG, MSG_LEN, TITLE)
-+#endif
-+
-+/* normal message context */
-+struct mmal_msg_context {
-+ union {
-+ struct {
-+ /* work struct for defered callback - must come first */
-+ struct work_struct work;
-+ /* mmal instance */
-+ struct vchiq_mmal_instance *instance;
-+ /* mmal port */
-+ struct vchiq_mmal_port *port;
-+ /* actual buffer used to store bulk reply */
-+ struct mmal_buffer *buffer;
-+ /* amount of buffer used */
-+ unsigned long buffer_used;
-+ /* MMAL buffer flags */
-+ u32 mmal_flags;
-+ /* Presentation and Decode timestamps */
-+ s64 pts;
-+ s64 dts;
-+
-+ int status; /* context status */
-+
-+ } bulk; /* bulk data */
-+
-+ struct {
-+ /* message handle to release */
-+ VCHI_HELD_MSG_T msg_handle;
-+ /* pointer to received message */
-+ struct mmal_msg *msg;
-+ /* received message length */
-+ u32 msg_len;
-+ /* completion upon reply */
-+ struct completion cmplt;
-+ } sync; /* synchronous response */
-+ } u;
-+
-+};
-+
-+struct vchiq_mmal_instance {
-+ VCHI_SERVICE_HANDLE_T handle;
-+
-+ /* ensure serialised access to service */
-+ struct mutex vchiq_mutex;
-+
-+ /* ensure serialised access to bulk operations */
-+ struct mutex bulk_mutex;
-+
-+ /* vmalloc page to receive scratch bulk xfers into */
-+ void *bulk_scratch;
-+
-+ /* component to use next */
-+ int component_idx;
-+ struct vchiq_mmal_component component[VCHIQ_MMAL_MAX_COMPONENTS];
-+};
-+
-+static struct mmal_msg_context *get_msg_context(struct vchiq_mmal_instance
-+ *instance)
-+{
-+ struct mmal_msg_context *msg_context;
-+
-+ /* todo: should this be allocated from a pool to avoid kmalloc */
-+ msg_context = kmalloc(sizeof(*msg_context), GFP_KERNEL);
-+ memset(msg_context, 0, sizeof(*msg_context));
-+
-+ return msg_context;
-+}
-+
-+static void release_msg_context(struct mmal_msg_context *msg_context)
-+{
-+ kfree(msg_context);
-+}
-+
-+/* deals with receipt of event to host message */
-+static void event_to_host_cb(struct vchiq_mmal_instance *instance,
-+ struct mmal_msg *msg, u32 msg_len)
-+{
-+ pr_debug("unhandled event\n");
-+ pr_debug("component:%p port type:%d num:%d cmd:0x%x length:%d\n",
-+ msg->u.event_to_host.client_component,
-+ msg->u.event_to_host.port_type,
-+ msg->u.event_to_host.port_num,
-+ msg->u.event_to_host.cmd, msg->u.event_to_host.length);
-+}
-+
-+/* workqueue scheduled callback
-+ *
-+ * we do this because it is important we do not call any other vchiq
-+ * sync calls from witin the message delivery thread
-+ */
-+static void buffer_work_cb(struct work_struct *work)
-+{
-+ struct mmal_msg_context *msg_context = (struct mmal_msg_context *)work;
-+
-+ msg_context->u.bulk.port->buffer_cb(msg_context->u.bulk.instance,
-+ msg_context->u.bulk.port,
-+ msg_context->u.bulk.status,
-+ msg_context->u.bulk.buffer,
-+ msg_context->u.bulk.buffer_used,
-+ msg_context->u.bulk.mmal_flags,
-+ msg_context->u.bulk.dts,
-+ msg_context->u.bulk.pts);
-+
-+ /* release message context */
-+ release_msg_context(msg_context);
-+}
-+
-+/* enqueue a bulk receive for a given message context */
-+static int bulk_receive(struct vchiq_mmal_instance *instance,
-+ struct mmal_msg *msg,
-+ struct mmal_msg_context *msg_context)
-+{
-+ unsigned long rd_len;
-+ unsigned long flags = 0;
-+ int ret;
-+
-+ /* bulk mutex stops other bulk operations while we have a
-+ * receive in progress - released in callback
-+ */
-+ ret = mutex_lock_interruptible(&instance->bulk_mutex);
-+ if (ret != 0)
-+ return ret;
-+
-+ rd_len = msg->u.buffer_from_host.buffer_header.length;
-+
-+ /* take buffer from queue */
-+ spin_lock_irqsave(&msg_context->u.bulk.port->slock, flags);
-+ if (list_empty(&msg_context->u.bulk.port->buffers)) {
-+ spin_unlock_irqrestore(&msg_context->u.bulk.port->slock, flags);
-+ pr_err("buffer list empty trying to submit bulk receive\n");
-+
-+ /* todo: this is a serious error, we should never have
-+ * commited a buffer_to_host operation to the mmal
-+ * port without the buffer to back it up (underflow
-+ * handling) and there is no obvious way to deal with
-+ * this - how is the mmal servie going to react when
-+ * we fail to do the xfer and reschedule a buffer when
-+ * it arrives? perhaps a starved flag to indicate a
-+ * waiting bulk receive?
-+ */
-+
-+ mutex_unlock(&instance->bulk_mutex);
-+
-+ return -EINVAL;
-+ }
-+
-+ msg_context->u.bulk.buffer =
-+ list_entry(msg_context->u.bulk.port->buffers.next,
-+ struct mmal_buffer, list);
-+ list_del(&msg_context->u.bulk.buffer->list);
-+
-+ spin_unlock_irqrestore(&msg_context->u.bulk.port->slock, flags);
-+
-+ /* ensure we do not overrun the available buffer */
-+ if (rd_len > msg_context->u.bulk.buffer->buffer_size) {
-+ rd_len = msg_context->u.bulk.buffer->buffer_size;
-+ pr_warn("short read as not enough receive buffer space\n");
-+ /* todo: is this the correct response, what happens to
-+ * the rest of the message data?
-+ */
-+ }
-+
-+ /* store length */
-+ msg_context->u.bulk.buffer_used = rd_len;
-+ msg_context->u.bulk.mmal_flags =
-+ msg->u.buffer_from_host.buffer_header.flags;
-+ msg_context->u.bulk.dts = msg->u.buffer_from_host.buffer_header.dts;
-+ msg_context->u.bulk.pts = msg->u.buffer_from_host.buffer_header.pts;
-+
-+ // only need to flush L1 cache here, as VCHIQ takes care of the L2
-+ // cache.
-+ __cpuc_flush_dcache_area(msg_context->u.bulk.buffer->buffer, rd_len);
-+
-+ /* queue the bulk submission */
-+ vchi_service_use(instance->handle);
-+ ret = vchi_bulk_queue_receive(instance->handle,
-+ msg_context->u.bulk.buffer->buffer,
-+ /* Actual receive needs to be a multiple
-+ * of 4 bytes
-+ */
-+ (rd_len + 3) & ~3,
-+ VCHI_FLAGS_CALLBACK_WHEN_OP_COMPLETE |
-+ VCHI_FLAGS_BLOCK_UNTIL_QUEUED,
-+ msg_context);
-+
-+ vchi_service_release(instance->handle);
-+
-+ if (ret != 0) {
-+ /* callback will not be clearing the mutex */
-+ mutex_unlock(&instance->bulk_mutex);
-+ }
-+
-+ return ret;
-+}
-+
-+/* enque a dummy bulk receive for a given message context */
-+static int dummy_bulk_receive(struct vchiq_mmal_instance *instance,
-+ struct mmal_msg_context *msg_context)
-+{
-+ int ret;
-+
-+ /* bulk mutex stops other bulk operations while we have a
-+ * receive in progress - released in callback
-+ */
-+ ret = mutex_lock_interruptible(&instance->bulk_mutex);
-+ if (ret != 0)
-+ return ret;
-+
-+ /* zero length indicates this was a dummy transfer */
-+ msg_context->u.bulk.buffer_used = 0;
-+
-+ /* queue the bulk submission */
-+ vchi_service_use(instance->handle);
-+
-+ ret = vchi_bulk_queue_receive(instance->handle,
-+ instance->bulk_scratch,
-+ 8,
-+ VCHI_FLAGS_CALLBACK_WHEN_OP_COMPLETE |
-+ VCHI_FLAGS_BLOCK_UNTIL_QUEUED,
-+ msg_context);
-+
-+ vchi_service_release(instance->handle);
-+
-+ if (ret != 0) {
-+ /* callback will not be clearing the mutex */
-+ mutex_unlock(&instance->bulk_mutex);
-+ }
-+
-+ return ret;
-+}
-+
-+/* data in message, memcpy from packet into output buffer */
-+static int inline_receive(struct vchiq_mmal_instance *instance,
-+ struct mmal_msg *msg,
-+ struct mmal_msg_context *msg_context)
-+{
-+ unsigned long flags = 0;
-+
-+ /* take buffer from queue */
-+ spin_lock_irqsave(&msg_context->u.bulk.port->slock, flags);
-+ if (list_empty(&msg_context->u.bulk.port->buffers)) {
-+ spin_unlock_irqrestore(&msg_context->u.bulk.port->slock, flags);
-+ pr_err("buffer list empty trying to receive inline\n");
-+
-+ /* todo: this is a serious error, we should never have
-+ * commited a buffer_to_host operation to the mmal
-+ * port without the buffer to back it up (with
-+ * underflow handling) and there is no obvious way to
-+ * deal with this. Less bad than the bulk case as we
-+ * can just drop this on the floor but...unhelpful
-+ */
-+ return -EINVAL;
-+ }
-+
-+ msg_context->u.bulk.buffer =
-+ list_entry(msg_context->u.bulk.port->buffers.next,
-+ struct mmal_buffer, list);
-+ list_del(&msg_context->u.bulk.buffer->list);
-+
-+ spin_unlock_irqrestore(&msg_context->u.bulk.port->slock, flags);
-+
-+ memcpy(msg_context->u.bulk.buffer->buffer,
-+ msg->u.buffer_from_host.short_data,
-+ msg->u.buffer_from_host.payload_in_message);
-+
-+ msg_context->u.bulk.buffer_used =
-+ msg->u.buffer_from_host.payload_in_message;
-+
-+ return 0;
-+}
-+
-+/* queue the buffer availability with MMAL_MSG_TYPE_BUFFER_FROM_HOST */
-+static int
-+buffer_from_host(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *port, struct mmal_buffer *buf)
-+{
-+ struct mmal_msg_context *msg_context;
-+ struct mmal_msg m;
-+ int ret;
-+
-+ pr_debug("instance:%p buffer:%p\n", instance->handle, buf);
-+
-+ /* bulk mutex stops other bulk operations while we
-+ * have a receive in progress
-+ */
-+ if (mutex_lock_interruptible(&instance->bulk_mutex))
-+ return -EINTR;
-+
-+ /* get context */
-+ msg_context = get_msg_context(instance);
-+ if (msg_context == NULL)
-+ return -ENOMEM;
-+
-+ /* store bulk message context for when data arrives */
-+ msg_context->u.bulk.instance = instance;
-+ msg_context->u.bulk.port = port;
-+ msg_context->u.bulk.buffer = NULL; /* not valid until bulk xfer */
-+ msg_context->u.bulk.buffer_used = 0;
-+
-+ /* initialise work structure ready to schedule callback */
-+ INIT_WORK(&msg_context->u.bulk.work, buffer_work_cb);
-+
-+ /* prep the buffer from host message */
-+ memset(&m, 0xbc, sizeof(m)); /* just to make debug clearer */
-+
-+ m.h.type = MMAL_MSG_TYPE_BUFFER_FROM_HOST;
-+ m.h.magic = MMAL_MAGIC;
-+ m.h.context = msg_context;
-+ m.h.status = 0;
-+
-+ /* drvbuf is our private data passed back */
-+ m.u.buffer_from_host.drvbuf.magic = MMAL_MAGIC;
-+ m.u.buffer_from_host.drvbuf.component_handle = port->component->handle;
-+ m.u.buffer_from_host.drvbuf.port_handle = port->handle;
-+ m.u.buffer_from_host.drvbuf.client_context = msg_context;
-+
-+ /* buffer header */
-+ m.u.buffer_from_host.buffer_header.cmd = 0;
-+ m.u.buffer_from_host.buffer_header.data = buf->buffer;
-+ m.u.buffer_from_host.buffer_header.alloc_size = buf->buffer_size;
-+ m.u.buffer_from_host.buffer_header.length = 0; /* nothing used yet */
-+ m.u.buffer_from_host.buffer_header.offset = 0; /* no offset */
-+ m.u.buffer_from_host.buffer_header.flags = 0; /* no flags */
-+ m.u.buffer_from_host.buffer_header.pts = MMAL_TIME_UNKNOWN;
-+ m.u.buffer_from_host.buffer_header.dts = MMAL_TIME_UNKNOWN;
-+
-+ /* clear buffer type sepecific data */
-+ memset(&m.u.buffer_from_host.buffer_header_type_specific, 0,
-+ sizeof(m.u.buffer_from_host.buffer_header_type_specific));
-+
-+ /* no payload in message */
-+ m.u.buffer_from_host.payload_in_message = 0;
-+
-+ vchi_service_use(instance->handle);
-+
-+ ret = vchi_msg_queue(instance->handle, &m,
-+ sizeof(struct mmal_msg_header) +
-+ sizeof(m.u.buffer_from_host),
-+ VCHI_FLAGS_BLOCK_UNTIL_QUEUED, NULL);
-+
-+ if (ret != 0) {
-+ release_msg_context(msg_context);
-+ /* todo: is this correct error value? */
-+ }
-+
-+ vchi_service_release(instance->handle);
-+
-+ mutex_unlock(&instance->bulk_mutex);
-+
-+ return ret;
-+}
-+
-+/* submit a buffer to the mmal sevice
-+ *
-+ * the buffer_from_host uses size data from the ports next available
-+ * mmal_buffer and deals with there being no buffer available by
-+ * incrementing the underflow for later
-+ */
-+static int port_buffer_from_host(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *port)
-+{
-+ int ret;
-+ struct mmal_buffer *buf;
-+ unsigned long flags = 0;
-+
-+ if (!port->enabled)
-+ return -EINVAL;
-+
-+ /* peek buffer from queue */
-+ spin_lock_irqsave(&port->slock, flags);
-+ if (list_empty(&port->buffers)) {
-+ port->buffer_underflow++;
-+ spin_unlock_irqrestore(&port->slock, flags);
-+ return -ENOSPC;
-+ }
-+
-+ buf = list_entry(port->buffers.next, struct mmal_buffer, list);
-+
-+ spin_unlock_irqrestore(&port->slock, flags);
-+
-+ /* issue buffer to mmal service */
-+ ret = buffer_from_host(instance, port, buf);
-+ if (ret) {
-+ pr_err("adding buffer header failed\n");
-+ /* todo: how should this be dealt with */
-+ }
-+
-+ return ret;
-+}
-+
-+/* deals with receipt of buffer to host message */
-+static void buffer_to_host_cb(struct vchiq_mmal_instance *instance,
-+ struct mmal_msg *msg, u32 msg_len)
-+{
-+ struct mmal_msg_context *msg_context;
-+
-+ pr_debug("buffer_to_host_cb: instance:%p msg:%p msg_len:%d\n",
-+ instance, msg, msg_len);
-+
-+ if (msg->u.buffer_from_host.drvbuf.magic == MMAL_MAGIC) {
-+ msg_context = msg->u.buffer_from_host.drvbuf.client_context;
-+ } else {
-+ pr_err("MMAL_MSG_TYPE_BUFFER_TO_HOST with bad magic\n");
-+ return;
-+ }
-+
-+ if (msg->h.status != MMAL_MSG_STATUS_SUCCESS) {
-+ /* message reception had an error */
-+ pr_warn("error %d in reply\n", msg->h.status);
-+
-+ msg_context->u.bulk.status = msg->h.status;
-+
-+ } else if (msg->u.buffer_from_host.buffer_header.length == 0) {
-+ /* empty buffer */
-+ if (msg->u.buffer_from_host.buffer_header.flags &
-+ MMAL_BUFFER_HEADER_FLAG_EOS) {
-+ msg_context->u.bulk.status =
-+ dummy_bulk_receive(instance, msg_context);
-+ if (msg_context->u.bulk.status == 0)
-+ return; /* successful bulk submission, bulk
-+ * completion will trigger callback
-+ */
-+ } else {
-+ /* do callback with empty buffer - not EOS though */
-+ msg_context->u.bulk.status = 0;
-+ msg_context->u.bulk.buffer_used = 0;
-+ }
-+ } else if (msg->u.buffer_from_host.payload_in_message == 0) {
-+ /* data is not in message, queue a bulk receive */
-+ msg_context->u.bulk.status =
-+ bulk_receive(instance, msg, msg_context);
-+ if (msg_context->u.bulk.status == 0)
-+ return; /* successful bulk submission, bulk
-+ * completion will trigger callback
-+ */
-+
-+ /* failed to submit buffer, this will end badly */
-+ pr_err("error %d on bulk submission\n",
-+ msg_context->u.bulk.status);
-+
-+ } else if (msg->u.buffer_from_host.payload_in_message <=
-+ MMAL_VC_SHORT_DATA) {
-+ /* data payload within message */
-+ msg_context->u.bulk.status = inline_receive(instance, msg,
-+ msg_context);
-+ } else {
-+ pr_err("message with invalid short payload\n");
-+
-+ /* signal error */
-+ msg_context->u.bulk.status = -EINVAL;
-+ msg_context->u.bulk.buffer_used =
-+ msg->u.buffer_from_host.payload_in_message;
-+ }
-+
-+ /* replace the buffer header */
-+ port_buffer_from_host(instance, msg_context->u.bulk.port);
-+
-+ /* schedule the port callback */
-+ schedule_work(&msg_context->u.bulk.work);
-+}
-+
-+static void bulk_receive_cb(struct vchiq_mmal_instance *instance,
-+ struct mmal_msg_context *msg_context)
-+{
-+ /* bulk receive operation complete */
-+ mutex_unlock(&msg_context->u.bulk.instance->bulk_mutex);
-+
-+ /* replace the buffer header */
-+ port_buffer_from_host(msg_context->u.bulk.instance,
-+ msg_context->u.bulk.port);
-+
-+ msg_context->u.bulk.status = 0;
-+
-+ /* schedule the port callback */
-+ schedule_work(&msg_context->u.bulk.work);
-+}
-+
-+static void bulk_abort_cb(struct vchiq_mmal_instance *instance,
-+ struct mmal_msg_context *msg_context)
-+{
-+ pr_err("%s: bulk ABORTED msg_context:%p\n", __func__, msg_context);
-+
-+ /* bulk receive operation complete */
-+ mutex_unlock(&msg_context->u.bulk.instance->bulk_mutex);
-+
-+ /* replace the buffer header */
-+ port_buffer_from_host(msg_context->u.bulk.instance,
-+ msg_context->u.bulk.port);
-+
-+ msg_context->u.bulk.status = -EINTR;
-+
-+ schedule_work(&msg_context->u.bulk.work);
-+}
-+
-+/* incoming event service callback */
-+static void service_callback(void *param,
-+ const VCHI_CALLBACK_REASON_T reason,
-+ void *bulk_ctx)
-+{
-+ struct vchiq_mmal_instance *instance = param;
-+ int status;
-+ u32 msg_len;
-+ struct mmal_msg *msg;
-+ VCHI_HELD_MSG_T msg_handle;
-+
-+ if (!instance) {
-+ pr_err("Message callback passed NULL instance\n");
-+ return;
-+ }
-+
-+ switch (reason) {
-+ case VCHI_CALLBACK_MSG_AVAILABLE:
-+ status = vchi_msg_hold(instance->handle, (void **)&msg,
-+ &msg_len, VCHI_FLAGS_NONE, &msg_handle);
-+ if (status) {
-+ pr_err("Unable to dequeue a message (%d)\n", status);
-+ break;
-+ }
-+
-+ DBG_DUMP_MSG(msg, msg_len, "<<< reply message");
-+
-+ /* handling is different for buffer messages */
-+ switch (msg->h.type) {
-+
-+ case MMAL_MSG_TYPE_BUFFER_FROM_HOST:
-+ vchi_held_msg_release(&msg_handle);
-+ break;
-+
-+ case MMAL_MSG_TYPE_EVENT_TO_HOST:
-+ event_to_host_cb(instance, msg, msg_len);
-+ vchi_held_msg_release(&msg_handle);
-+
-+ break;
-+
-+ case MMAL_MSG_TYPE_BUFFER_TO_HOST:
-+ buffer_to_host_cb(instance, msg, msg_len);
-+ vchi_held_msg_release(&msg_handle);
-+ break;
-+
-+ default:
-+ /* messages dependant on header context to complete */
-+
-+ /* todo: the msg.context really ought to be sanity
-+ * checked before we just use it, afaict it comes back
-+ * and is used raw from the videocore. Perhaps it
-+ * should be verified the address lies in the kernel
-+ * address space.
-+ */
-+ if (msg->h.context == NULL) {
-+ pr_err("received message context was null!\n");
-+ vchi_held_msg_release(&msg_handle);
-+ break;
-+ }
-+
-+ /* fill in context values */
-+ msg->h.context->u.sync.msg_handle = msg_handle;
-+ msg->h.context->u.sync.msg = msg;
-+ msg->h.context->u.sync.msg_len = msg_len;
-+
-+ /* todo: should this check (completion_done()
-+ * == 1) for no one waiting? or do we need a
-+ * flag to tell us the completion has been
-+ * interrupted so we can free the message and
-+ * its context. This probably also solves the
-+ * message arriving after interruption todo
-+ * below
-+ */
-+
-+ /* complete message so caller knows it happened */
-+ complete(&msg->h.context->u.sync.cmplt);
-+ break;
-+ }
-+
-+ break;
-+
-+ case VCHI_CALLBACK_BULK_RECEIVED:
-+ bulk_receive_cb(instance, bulk_ctx);
-+ break;
-+
-+ case VCHI_CALLBACK_BULK_RECEIVE_ABORTED:
-+ bulk_abort_cb(instance, bulk_ctx);
-+ break;
-+
-+ case VCHI_CALLBACK_SERVICE_CLOSED:
-+ /* TODO: consider if this requires action if received when
-+ * driver is not explicitly closing the service
-+ */
-+ break;
-+
-+ default:
-+ pr_err("Received unhandled message reason %d\n", reason);
-+ break;
-+ }
-+}
-+
-+static int send_synchronous_mmal_msg(struct vchiq_mmal_instance *instance,
-+ struct mmal_msg *msg,
-+ unsigned int payload_len,
-+ struct mmal_msg **msg_out,
-+ VCHI_HELD_MSG_T *msg_handle_out)
-+{
-+ struct mmal_msg_context msg_context;
-+ int ret;
-+
-+ /* payload size must not cause message to exceed max size */
-+ if (payload_len >
-+ (MMAL_MSG_MAX_SIZE - sizeof(struct mmal_msg_header))) {
-+ pr_err("payload length %d exceeds max:%d\n", payload_len,
-+ (MMAL_MSG_MAX_SIZE - sizeof(struct mmal_msg_header)));
-+ return -EINVAL;
-+ }
-+
-+ init_completion(&msg_context.u.sync.cmplt);
-+
-+ msg->h.magic = MMAL_MAGIC;
-+ msg->h.context = &msg_context;
-+ msg->h.status = 0;
-+
-+ DBG_DUMP_MSG(msg, (sizeof(struct mmal_msg_header) + payload_len),
-+ ">>> sync message");
-+
-+ vchi_service_use(instance->handle);
-+
-+ ret = vchi_msg_queue(instance->handle,
-+ msg,
-+ sizeof(struct mmal_msg_header) + payload_len,
-+ VCHI_FLAGS_BLOCK_UNTIL_QUEUED, NULL);
-+
-+ vchi_service_release(instance->handle);
-+
-+ if (ret) {
-+ pr_err("error %d queuing message\n", ret);
-+ return ret;
-+ }
-+
-+ ret = wait_for_completion_timeout(&msg_context.u.sync.cmplt, 3*HZ);
-+ if (ret <= 0) {
-+ pr_err("error %d waiting for sync completion\n", ret);
-+ if (ret == 0)
-+ ret = -ETIME;
-+ /* todo: what happens if the message arrives after aborting */
-+ return ret;
-+ }
-+
-+ *msg_out = msg_context.u.sync.msg;
-+ *msg_handle_out = msg_context.u.sync.msg_handle;
-+
-+ return 0;
-+}
-+
-+static void dump_port_info(struct vchiq_mmal_port *port)
-+{
-+ pr_debug("port handle:0x%x enabled:%d\n", port->handle, port->enabled);
-+
-+ pr_debug("buffer minimum num:%d size:%d align:%d\n",
-+ port->minimum_buffer.num,
-+ port->minimum_buffer.size, port->minimum_buffer.alignment);
-+
-+ pr_debug("buffer recommended num:%d size:%d align:%d\n",
-+ port->recommended_buffer.num,
-+ port->recommended_buffer.size,
-+ port->recommended_buffer.alignment);
-+
-+ pr_debug("buffer current values num:%d size:%d align:%d\n",
-+ port->current_buffer.num,
-+ port->current_buffer.size, port->current_buffer.alignment);
-+
-+ pr_debug("elementry stream: type:%d encoding:0x%x varient:0x%x\n",
-+ port->format.type,
-+ port->format.encoding, port->format.encoding_variant);
-+
-+ pr_debug(" bitrate:%d flags:0x%x\n",
-+ port->format.bitrate, port->format.flags);
-+
-+ if (port->format.type == MMAL_ES_TYPE_VIDEO) {
-+ pr_debug
-+ ("es video format: width:%d height:%d colourspace:0x%x\n",
-+ port->es.video.width, port->es.video.height,
-+ port->es.video.color_space);
-+
-+ pr_debug(" : crop xywh %d,%d,%d,%d\n",
-+ port->es.video.crop.x,
-+ port->es.video.crop.y,
-+ port->es.video.crop.width, port->es.video.crop.height);
-+ pr_debug(" : framerate %d/%d aspect %d/%d\n",
-+ port->es.video.frame_rate.num,
-+ port->es.video.frame_rate.den,
-+ port->es.video.par.num, port->es.video.par.den);
-+ }
-+}
-+
-+static void port_to_mmal_msg(struct vchiq_mmal_port *port, struct mmal_port *p)
-+{
-+
-+ /* todo do readonly fields need setting at all? */
-+ p->type = port->type;
-+ p->index = port->index;
-+ p->index_all = 0;
-+ p->is_enabled = port->enabled;
-+ p->buffer_num_min = port->minimum_buffer.num;
-+ p->buffer_size_min = port->minimum_buffer.size;
-+ p->buffer_alignment_min = port->minimum_buffer.alignment;
-+ p->buffer_num_recommended = port->recommended_buffer.num;
-+ p->buffer_size_recommended = port->recommended_buffer.size;
-+
-+ /* only three writable fields in a port */
-+ p->buffer_num = port->current_buffer.num;
-+ p->buffer_size = port->current_buffer.size;
-+ p->userdata = port;
-+}
-+
-+static int port_info_set(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *port)
-+{
-+ int ret;
-+ struct mmal_msg m;
-+ struct mmal_msg *rmsg;
-+ VCHI_HELD_MSG_T rmsg_handle;
-+
-+ pr_debug("setting port info port %p\n", port);
-+ if (!port)
-+ return -1;
-+ dump_port_info(port);
-+
-+ m.h.type = MMAL_MSG_TYPE_PORT_INFO_SET;
-+
-+ m.u.port_info_set.component_handle = port->component->handle;
-+ m.u.port_info_set.port_type = port->type;
-+ m.u.port_info_set.port_index = port->index;
-+
-+ port_to_mmal_msg(port, &m.u.port_info_set.port);
-+
-+ /* elementry stream format setup */
-+ m.u.port_info_set.format.type = port->format.type;
-+ m.u.port_info_set.format.encoding = port->format.encoding;
-+ m.u.port_info_set.format.encoding_variant =
-+ port->format.encoding_variant;
-+ m.u.port_info_set.format.bitrate = port->format.bitrate;
-+ m.u.port_info_set.format.flags = port->format.flags;
-+
-+ memcpy(&m.u.port_info_set.es, &port->es,
-+ sizeof(union mmal_es_specific_format));
-+
-+ m.u.port_info_set.format.extradata_size = port->format.extradata_size;
-+ memcpy(&m.u.port_info_set.extradata, port->format.extradata,
-+ port->format.extradata_size);
-+
-+ ret = send_synchronous_mmal_msg(instance, &m,
-+ sizeof(m.u.port_info_set),
-+ &rmsg, &rmsg_handle);
-+ if (ret)
-+ return ret;
-+
-+ if (rmsg->h.type != MMAL_MSG_TYPE_PORT_INFO_SET) {
-+ /* got an unexpected message type in reply */
-+ ret = -EINVAL;
-+ goto release_msg;
-+ }
-+
-+ /* return operation status */
-+ ret = -rmsg->u.port_info_get_reply.status;
-+
-+ pr_debug("%s:result:%d component:0x%x port:%d\n", __func__, ret,
-+ port->component->handle, port->handle);
-+
-+release_msg:
-+ vchi_held_msg_release(&rmsg_handle);
-+
-+ return ret;
-+
-+}
-+
-+/* use port info get message to retrive port information */
-+static int port_info_get(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *port)
-+{
-+ int ret;
-+ struct mmal_msg m;
-+ struct mmal_msg *rmsg;
-+ VCHI_HELD_MSG_T rmsg_handle;
-+
-+ /* port info time */
-+ m.h.type = MMAL_MSG_TYPE_PORT_INFO_GET;
-+ m.u.port_info_get.component_handle = port->component->handle;
-+ m.u.port_info_get.port_type = port->type;
-+ m.u.port_info_get.index = port->index;
-+
-+ ret = send_synchronous_mmal_msg(instance, &m,
-+ sizeof(m.u.port_info_get),
-+ &rmsg, &rmsg_handle);
-+ if (ret)
-+ return ret;
-+
-+ if (rmsg->h.type != MMAL_MSG_TYPE_PORT_INFO_GET) {
-+ /* got an unexpected message type in reply */
-+ ret = -EINVAL;
-+ goto release_msg;
-+ }
-+
-+ /* return operation status */
-+ ret = -rmsg->u.port_info_get_reply.status;
-+ if (ret != MMAL_MSG_STATUS_SUCCESS)
-+ goto release_msg;
-+
-+ if (rmsg->u.port_info_get_reply.port.is_enabled == 0)
-+ port->enabled = false;
-+ else
-+ port->enabled = true;
-+
-+ /* copy the values out of the message */
-+ port->handle = rmsg->u.port_info_get_reply.port_handle;
-+
-+ /* port type and index cached to use on port info set becuase
-+ * it does not use a port handle
-+ */
-+ port->type = rmsg->u.port_info_get_reply.port_type;
-+ port->index = rmsg->u.port_info_get_reply.port_index;
-+
-+ port->minimum_buffer.num =
-+ rmsg->u.port_info_get_reply.port.buffer_num_min;
-+ port->minimum_buffer.size =
-+ rmsg->u.port_info_get_reply.port.buffer_size_min;
-+ port->minimum_buffer.alignment =
-+ rmsg->u.port_info_get_reply.port.buffer_alignment_min;
-+
-+ port->recommended_buffer.alignment =
-+ rmsg->u.port_info_get_reply.port.buffer_alignment_min;
-+ port->recommended_buffer.num =
-+ rmsg->u.port_info_get_reply.port.buffer_num_recommended;
-+
-+ port->current_buffer.num = rmsg->u.port_info_get_reply.port.buffer_num;
-+ port->current_buffer.size =
-+ rmsg->u.port_info_get_reply.port.buffer_size;
-+
-+ /* stream format */
-+ port->format.type = rmsg->u.port_info_get_reply.format.type;
-+ port->format.encoding = rmsg->u.port_info_get_reply.format.encoding;
-+ port->format.encoding_variant =
-+ rmsg->u.port_info_get_reply.format.encoding_variant;
-+ port->format.bitrate = rmsg->u.port_info_get_reply.format.bitrate;
-+ port->format.flags = rmsg->u.port_info_get_reply.format.flags;
-+
-+ /* elementry stream format */
-+ memcpy(&port->es,
-+ &rmsg->u.port_info_get_reply.es,
-+ sizeof(union mmal_es_specific_format));
-+ port->format.es = &port->es;
-+
-+ port->format.extradata_size =
-+ rmsg->u.port_info_get_reply.format.extradata_size;
-+ memcpy(port->format.extradata,
-+ rmsg->u.port_info_get_reply.extradata,
-+ port->format.extradata_size);
-+
-+ pr_debug("received port info\n");
-+ dump_port_info(port);
-+
-+release_msg:
-+
-+ pr_debug("%s:result:%d component:0x%x port:%d\n",
-+ __func__, ret, port->component->handle, port->handle);
-+
-+ vchi_held_msg_release(&rmsg_handle);
-+
-+ return ret;
-+}
-+
-+/* create comonent on vc */
-+static int create_component(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_component *component,
-+ const char *name)
-+{
-+ int ret;
-+ struct mmal_msg m;
-+ struct mmal_msg *rmsg;
-+ VCHI_HELD_MSG_T rmsg_handle;
-+
-+ /* build component create message */
-+ m.h.type = MMAL_MSG_TYPE_COMPONENT_CREATE;
-+ m.u.component_create.client_component = component;
-+ strncpy(m.u.component_create.name, name,
-+ sizeof(m.u.component_create.name));
-+
-+ ret = send_synchronous_mmal_msg(instance, &m,
-+ sizeof(m.u.component_create),
-+ &rmsg, &rmsg_handle);
-+ if (ret)
-+ return ret;
-+
-+ if (rmsg->h.type != m.h.type) {
-+ /* got an unexpected message type in reply */
-+ ret = -EINVAL;
-+ goto release_msg;
-+ }
-+
-+ ret = -rmsg->u.component_create_reply.status;
-+ if (ret != MMAL_MSG_STATUS_SUCCESS)
-+ goto release_msg;
-+
-+ /* a valid component response received */
-+ component->handle = rmsg->u.component_create_reply.component_handle;
-+ component->inputs = rmsg->u.component_create_reply.input_num;
-+ component->outputs = rmsg->u.component_create_reply.output_num;
-+ component->clocks = rmsg->u.component_create_reply.clock_num;
-+
-+ pr_debug("Component handle:0x%x in:%d out:%d clock:%d\n",
-+ component->handle,
-+ component->inputs, component->outputs, component->clocks);
-+
-+release_msg:
-+ vchi_held_msg_release(&rmsg_handle);
-+
-+ return ret;
-+}
-+
-+/* destroys a component on vc */
-+static int destroy_component(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_component *component)
-+{
-+ int ret;
-+ struct mmal_msg m;
-+ struct mmal_msg *rmsg;
-+ VCHI_HELD_MSG_T rmsg_handle;
-+
-+ m.h.type = MMAL_MSG_TYPE_COMPONENT_DESTROY;
-+ m.u.component_destroy.component_handle = component->handle;
-+
-+ ret = send_synchronous_mmal_msg(instance, &m,
-+ sizeof(m.u.component_destroy),
-+ &rmsg, &rmsg_handle);
-+ if (ret)
-+ return ret;
-+
-+ if (rmsg->h.type != m.h.type) {
-+ /* got an unexpected message type in reply */
-+ ret = -EINVAL;
-+ goto release_msg;
-+ }
-+
-+ ret = -rmsg->u.component_destroy_reply.status;
-+
-+release_msg:
-+
-+ vchi_held_msg_release(&rmsg_handle);
-+
-+ return ret;
-+}
-+
-+/* enable a component on vc */
-+static int enable_component(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_component *component)
-+{
-+ int ret;
-+ struct mmal_msg m;
-+ struct mmal_msg *rmsg;
-+ VCHI_HELD_MSG_T rmsg_handle;
-+
-+ m.h.type = MMAL_MSG_TYPE_COMPONENT_ENABLE;
-+ m.u.component_enable.component_handle = component->handle;
-+
-+ ret = send_synchronous_mmal_msg(instance, &m,
-+ sizeof(m.u.component_enable),
-+ &rmsg, &rmsg_handle);
-+ if (ret)
-+ return ret;
-+
-+ if (rmsg->h.type != m.h.type) {
-+ /* got an unexpected message type in reply */
-+ ret = -EINVAL;
-+ goto release_msg;
-+ }
-+
-+ ret = -rmsg->u.component_enable_reply.status;
-+
-+release_msg:
-+ vchi_held_msg_release(&rmsg_handle);
-+
-+ return ret;
-+}
-+
-+/* disable a component on vc */
-+static int disable_component(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_component *component)
-+{
-+ int ret;
-+ struct mmal_msg m;
-+ struct mmal_msg *rmsg;
-+ VCHI_HELD_MSG_T rmsg_handle;
-+
-+ m.h.type = MMAL_MSG_TYPE_COMPONENT_DISABLE;
-+ m.u.component_disable.component_handle = component->handle;
-+
-+ ret = send_synchronous_mmal_msg(instance, &m,
-+ sizeof(m.u.component_disable),
-+ &rmsg, &rmsg_handle);
-+ if (ret)
-+ return ret;
-+
-+ if (rmsg->h.type != m.h.type) {
-+ /* got an unexpected message type in reply */
-+ ret = -EINVAL;
-+ goto release_msg;
-+ }
-+
-+ ret = -rmsg->u.component_disable_reply.status;
-+
-+release_msg:
-+
-+ vchi_held_msg_release(&rmsg_handle);
-+
-+ return ret;
-+}
-+
-+/* get version of mmal implementation */
-+static int get_version(struct vchiq_mmal_instance *instance,
-+ u32 *major_out, u32 *minor_out)
-+{
-+ int ret;
-+ struct mmal_msg m;
-+ struct mmal_msg *rmsg;
-+ VCHI_HELD_MSG_T rmsg_handle;
-+
-+ m.h.type = MMAL_MSG_TYPE_GET_VERSION;
-+
-+ ret = send_synchronous_mmal_msg(instance, &m,
-+ sizeof(m.u.version),
-+ &rmsg, &rmsg_handle);
-+ if (ret)
-+ return ret;
-+
-+ if (rmsg->h.type != m.h.type) {
-+ /* got an unexpected message type in reply */
-+ ret = -EINVAL;
-+ goto release_msg;
-+ }
-+
-+ *major_out = rmsg->u.version.major;
-+ *minor_out = rmsg->u.version.minor;
-+
-+release_msg:
-+ vchi_held_msg_release(&rmsg_handle);
-+
-+ return ret;
-+}
-+
-+/* do a port action with a port as a parameter */
-+static int port_action_port(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *port,
-+ enum mmal_msg_port_action_type action_type)
-+{
-+ int ret;
-+ struct mmal_msg m;
-+ struct mmal_msg *rmsg;
-+ VCHI_HELD_MSG_T rmsg_handle;
-+
-+ m.h.type = MMAL_MSG_TYPE_PORT_ACTION;
-+ m.u.port_action_port.component_handle = port->component->handle;
-+ m.u.port_action_port.port_handle = port->handle;
-+ m.u.port_action_port.action = action_type;
-+
-+ port_to_mmal_msg(port, &m.u.port_action_port.port);
-+
-+ ret = send_synchronous_mmal_msg(instance, &m,
-+ sizeof(m.u.port_action_port),
-+ &rmsg, &rmsg_handle);
-+ if (ret)
-+ return ret;
-+
-+ if (rmsg->h.type != MMAL_MSG_TYPE_PORT_ACTION) {
-+ /* got an unexpected message type in reply */
-+ ret = -EINVAL;
-+ goto release_msg;
-+ }
-+
-+ ret = -rmsg->u.port_action_reply.status;
-+
-+ pr_debug("%s:result:%d component:0x%x port:%d action:%s(%d)\n",
-+ __func__,
-+ ret, port->component->handle, port->handle,
-+ port_action_type_names[action_type], action_type);
-+
-+release_msg:
-+ vchi_held_msg_release(&rmsg_handle);
-+
-+ return ret;
-+}
-+
-+/* do a port action with handles as parameters */
-+static int port_action_handle(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *port,
-+ enum mmal_msg_port_action_type action_type,
-+ u32 connect_component_handle,
-+ u32 connect_port_handle)
-+{
-+ int ret;
-+ struct mmal_msg m;
-+ struct mmal_msg *rmsg;
-+ VCHI_HELD_MSG_T rmsg_handle;
-+
-+ m.h.type = MMAL_MSG_TYPE_PORT_ACTION;
-+
-+ m.u.port_action_handle.component_handle = port->component->handle;
-+ m.u.port_action_handle.port_handle = port->handle;
-+ m.u.port_action_handle.action = action_type;
-+
-+ m.u.port_action_handle.connect_component_handle =
-+ connect_component_handle;
-+ m.u.port_action_handle.connect_port_handle = connect_port_handle;
-+
-+ ret = send_synchronous_mmal_msg(instance, &m,
-+ sizeof(m.u.port_action_handle),
-+ &rmsg, &rmsg_handle);
-+ if (ret)
-+ return ret;
-+
-+ if (rmsg->h.type != MMAL_MSG_TYPE_PORT_ACTION) {
-+ /* got an unexpected message type in reply */
-+ ret = -EINVAL;
-+ goto release_msg;
-+ }
-+
-+ ret = -rmsg->u.port_action_reply.status;
-+
-+ pr_debug("%s:result:%d component:0x%x port:%d action:%s(%d)" \
-+ " connect component:0x%x connect port:%d\n",
-+ __func__,
-+ ret, port->component->handle, port->handle,
-+ port_action_type_names[action_type],
-+ action_type, connect_component_handle, connect_port_handle);
-+
-+release_msg:
-+ vchi_held_msg_release(&rmsg_handle);
-+
-+ return ret;
-+}
-+
-+static int port_parameter_set(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *port,
-+ u32 parameter_id, void *value, u32 value_size)
-+{
-+ int ret;
-+ struct mmal_msg m;
-+ struct mmal_msg *rmsg;
-+ VCHI_HELD_MSG_T rmsg_handle;
-+
-+ m.h.type = MMAL_MSG_TYPE_PORT_PARAMETER_SET;
-+
-+ m.u.port_parameter_set.component_handle = port->component->handle;
-+ m.u.port_parameter_set.port_handle = port->handle;
-+ m.u.port_parameter_set.id = parameter_id;
-+ m.u.port_parameter_set.size = (2 * sizeof(u32)) + value_size;
-+ memcpy(&m.u.port_parameter_set.value, value, value_size);
-+
-+ ret = send_synchronous_mmal_msg(instance, &m,
-+ (4 * sizeof(u32)) + value_size,
-+ &rmsg, &rmsg_handle);
-+ if (ret)
-+ return ret;
-+
-+ if (rmsg->h.type != MMAL_MSG_TYPE_PORT_PARAMETER_SET) {
-+ /* got an unexpected message type in reply */
-+ ret = -EINVAL;
-+ goto release_msg;
-+ }
-+
-+ ret = -rmsg->u.port_parameter_set_reply.status;
-+
-+ pr_debug("%s:result:%d component:0x%x port:%d parameter:%d\n",
-+ __func__,
-+ ret, port->component->handle, port->handle, parameter_id);
-+
-+release_msg:
-+ vchi_held_msg_release(&rmsg_handle);
-+
-+ return ret;
-+}
-+
-+static int port_parameter_get(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *port,
-+ u32 parameter_id, void *value, u32 *value_size)
-+{
-+ int ret;
-+ struct mmal_msg m;
-+ struct mmal_msg *rmsg;
-+ VCHI_HELD_MSG_T rmsg_handle;
-+
-+ m.h.type = MMAL_MSG_TYPE_PORT_PARAMETER_GET;
-+
-+ m.u.port_parameter_get.component_handle = port->component->handle;
-+ m.u.port_parameter_get.port_handle = port->handle;
-+ m.u.port_parameter_get.id = parameter_id;
-+ m.u.port_parameter_get.size = (2 * sizeof(u32)) + *value_size;
-+
-+ ret = send_synchronous_mmal_msg(instance, &m,
-+ sizeof(struct
-+ mmal_msg_port_parameter_get),
-+ &rmsg, &rmsg_handle);
-+ if (ret)
-+ return ret;
-+
-+ if (rmsg->h.type != MMAL_MSG_TYPE_PORT_PARAMETER_GET) {
-+ /* got an unexpected message type in reply */
-+ pr_err("Incorrect reply type %d\n", rmsg->h.type);
-+ ret = -EINVAL;
-+ goto release_msg;
-+ }
-+
-+ ret = -rmsg->u.port_parameter_get_reply.status;
-+ if (ret) {
-+ /* Copy only as much as we have space for
-+ * but report true size of parameter
-+ */
-+ memcpy(value, &rmsg->u.port_parameter_get_reply.value,
-+ *value_size);
-+ *value_size = rmsg->u.port_parameter_get_reply.size;
-+ } else
-+ memcpy(value, &rmsg->u.port_parameter_get_reply.value,
-+ rmsg->u.port_parameter_get_reply.size);
-+
-+ pr_debug("%s:result:%d component:0x%x port:%d parameter:%d\n", __func__,
-+ ret, port->component->handle, port->handle, parameter_id);
-+
-+release_msg:
-+ vchi_held_msg_release(&rmsg_handle);
-+
-+ return ret;
-+}
-+
-+/* disables a port and drains buffers from it */
-+static int port_disable(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *port)
-+{
-+ int ret;
-+ struct list_head *q, *buf_head;
-+ unsigned long flags = 0;
-+
-+ if (!port->enabled)
-+ return 0;
-+
-+ port->enabled = false;
-+
-+ ret = port_action_port(instance, port,
-+ MMAL_MSG_PORT_ACTION_TYPE_DISABLE);
-+ if (ret == 0) {
-+
-+ /* drain all queued buffers on port */
-+ spin_lock_irqsave(&port->slock, flags);
-+
-+ list_for_each_safe(buf_head, q, &port->buffers) {
-+ struct mmal_buffer *mmalbuf;
-+ mmalbuf = list_entry(buf_head, struct mmal_buffer,
-+ list);
-+ list_del(buf_head);
-+ if (port->buffer_cb)
-+ port->buffer_cb(instance,
-+ port, 0, mmalbuf, 0, 0,
-+ MMAL_TIME_UNKNOWN,
-+ MMAL_TIME_UNKNOWN);
-+ }
-+
-+ spin_unlock_irqrestore(&port->slock, flags);
-+
-+ ret = port_info_get(instance, port);
-+ }
-+
-+ return ret;
-+}
-+
-+/* enable a port */
-+static int port_enable(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *port)
-+{
-+ unsigned int hdr_count;
-+ struct list_head *buf_head;
-+ int ret;
-+
-+ if (port->enabled)
-+ return 0;
-+
-+ /* ensure there are enough buffers queued to cover the buffer headers */
-+ if (port->buffer_cb != NULL) {
-+ hdr_count = 0;
-+ list_for_each(buf_head, &port->buffers) {
-+ hdr_count++;
-+ }
-+ if (hdr_count < port->current_buffer.num)
-+ return -ENOSPC;
-+ }
-+
-+ ret = port_action_port(instance, port,
-+ MMAL_MSG_PORT_ACTION_TYPE_ENABLE);
-+ if (ret)
-+ goto done;
-+
-+ port->enabled = true;
-+
-+ if (port->buffer_cb) {
-+ /* send buffer headers to videocore */
-+ hdr_count = 1;
-+ list_for_each(buf_head, &port->buffers) {
-+ struct mmal_buffer *mmalbuf;
-+ mmalbuf = list_entry(buf_head, struct mmal_buffer,
-+ list);
-+ ret = buffer_from_host(instance, port, mmalbuf);
-+ if (ret)
-+ goto done;
-+
-+ hdr_count++;
-+ if (hdr_count > port->current_buffer.num)
-+ break;
-+ }
-+ }
-+
-+ ret = port_info_get(instance, port);
-+
-+done:
-+ return ret;
-+}
-+
-+/* ------------------------------------------------------------------
-+ * Exported API
-+ *------------------------------------------------------------------*/
-+
-+int vchiq_mmal_port_set_format(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *port)
-+{
-+ int ret;
-+
-+ if (mutex_lock_interruptible(&instance->vchiq_mutex))
-+ return -EINTR;
-+
-+ ret = port_info_set(instance, port);
-+ if (ret)
-+ goto release_unlock;
-+
-+ /* read what has actually been set */
-+ ret = port_info_get(instance, port);
-+
-+release_unlock:
-+ mutex_unlock(&instance->vchiq_mutex);
-+
-+ return ret;
-+
-+}
-+
-+int vchiq_mmal_port_parameter_set(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *port,
-+ u32 parameter, void *value, u32 value_size)
-+{
-+ int ret;
-+
-+ if (mutex_lock_interruptible(&instance->vchiq_mutex))
-+ return -EINTR;
-+
-+ ret = port_parameter_set(instance, port, parameter, value, value_size);
-+
-+ mutex_unlock(&instance->vchiq_mutex);
-+
-+ return ret;
-+}
-+
-+int vchiq_mmal_port_parameter_get(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *port,
-+ u32 parameter, void *value, u32 *value_size)
-+{
-+ int ret;
-+
-+ if (mutex_lock_interruptible(&instance->vchiq_mutex))
-+ return -EINTR;
-+
-+ ret = port_parameter_get(instance, port, parameter, value, value_size);
-+
-+ mutex_unlock(&instance->vchiq_mutex);
-+
-+ return ret;
-+}
-+
-+/* enable a port
-+ *
-+ * enables a port and queues buffers for satisfying callbacks if we
-+ * provide a callback handler
-+ */
-+int vchiq_mmal_port_enable(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *port,
-+ vchiq_mmal_buffer_cb buffer_cb)
-+{
-+ int ret;
-+
-+ if (mutex_lock_interruptible(&instance->vchiq_mutex))
-+ return -EINTR;
-+
-+ /* already enabled - noop */
-+ if (port->enabled) {
-+ ret = 0;
-+ goto unlock;
-+ }
-+
-+ port->buffer_cb = buffer_cb;
-+
-+ ret = port_enable(instance, port);
-+
-+unlock:
-+ mutex_unlock(&instance->vchiq_mutex);
-+
-+ return ret;
-+}
-+
-+int vchiq_mmal_port_disable(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *port)
-+{
-+ int ret;
-+
-+ if (mutex_lock_interruptible(&instance->vchiq_mutex))
-+ return -EINTR;
-+
-+ if (!port->enabled) {
-+ mutex_unlock(&instance->vchiq_mutex);
-+ return 0;
-+ }
-+
-+ ret = port_disable(instance, port);
-+
-+ mutex_unlock(&instance->vchiq_mutex);
-+
-+ return ret;
-+}
-+
-+/* ports will be connected in a tunneled manner so data buffers
-+ * are not handled by client.
-+ */
-+int vchiq_mmal_port_connect_tunnel(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *src,
-+ struct vchiq_mmal_port *dst)
-+{
-+ int ret;
-+
-+ if (mutex_lock_interruptible(&instance->vchiq_mutex))
-+ return -EINTR;
-+
-+ /* disconnect ports if connected */
-+ if (src->connected != NULL) {
-+ ret = port_disable(instance, src);
-+ if (ret) {
-+ pr_err("failed disabling src port(%d)\n", ret);
-+ goto release_unlock;
-+ }
-+
-+ /* do not need to disable the destination port as they
-+ * are connected and it is done automatically
-+ */
-+
-+ ret = port_action_handle(instance, src,
-+ MMAL_MSG_PORT_ACTION_TYPE_DISCONNECT,
-+ src->connected->component->handle,
-+ src->connected->handle);
-+ if (ret < 0) {
-+ pr_err("failed disconnecting src port\n");
-+ goto release_unlock;
-+ }
-+ src->connected->enabled = false;
-+ src->connected = NULL;
-+ }
-+
-+ if (dst == NULL) {
-+ /* do not make new connection */
-+ ret = 0;
-+ pr_debug("not making new connection\n");
-+ goto release_unlock;
-+ }
-+
-+ /* copy src port format to dst */
-+ dst->format.encoding = src->format.encoding;
-+ dst->es.video.width = src->es.video.width;
-+ dst->es.video.height = src->es.video.height;
-+ dst->es.video.crop.x = src->es.video.crop.x;
-+ dst->es.video.crop.y = src->es.video.crop.y;
-+ dst->es.video.crop.width = src->es.video.crop.width;
-+ dst->es.video.crop.height = src->es.video.crop.height;
-+ dst->es.video.frame_rate.num = src->es.video.frame_rate.num;
-+ dst->es.video.frame_rate.den = src->es.video.frame_rate.den;
-+
-+ /* set new format */
-+ ret = port_info_set(instance, dst);
-+ if (ret) {
-+ pr_debug("setting port info failed\n");
-+ goto release_unlock;
-+ }
-+
-+ /* read what has actually been set */
-+ ret = port_info_get(instance, dst);
-+ if (ret) {
-+ pr_debug("read back port info failed\n");
-+ goto release_unlock;
-+ }
-+
-+ /* connect two ports together */
-+ ret = port_action_handle(instance, src,
-+ MMAL_MSG_PORT_ACTION_TYPE_CONNECT,
-+ dst->component->handle, dst->handle);
-+ if (ret < 0) {
-+ pr_debug("connecting port %d:%d to %d:%d failed\n",
-+ src->component->handle, src->handle,
-+ dst->component->handle, dst->handle);
-+ goto release_unlock;
-+ }
-+ src->connected = dst;
-+
-+release_unlock:
-+
-+ mutex_unlock(&instance->vchiq_mutex);
-+
-+ return ret;
-+}
-+
-+int vchiq_mmal_submit_buffer(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *port,
-+ struct mmal_buffer *buffer)
-+{
-+ unsigned long flags = 0;
-+
-+ spin_lock_irqsave(&port->slock, flags);
-+ list_add_tail(&buffer->list, &port->buffers);
-+ spin_unlock_irqrestore(&port->slock, flags);
-+
-+ /* the port previously underflowed because it was missing a
-+ * mmal_buffer which has just been added, submit that buffer
-+ * to the mmal service.
-+ */
-+ if (port->buffer_underflow) {
-+ port_buffer_from_host(instance, port);
-+ port->buffer_underflow--;
-+ }
-+
-+ return 0;
-+}
-+
-+/* Initialise a mmal component and its ports
-+ *
-+ */
-+int vchiq_mmal_component_init(struct vchiq_mmal_instance *instance,
-+ const char *name,
-+ struct vchiq_mmal_component **component_out)
-+{
-+ int ret;
-+ int idx; /* port index */
-+ struct vchiq_mmal_component *component;
-+
-+ if (mutex_lock_interruptible(&instance->vchiq_mutex))
-+ return -EINTR;
-+
-+ if (instance->component_idx == VCHIQ_MMAL_MAX_COMPONENTS) {
-+ ret = -EINVAL; /* todo is this correct error? */
-+ goto unlock;
-+ }
-+
-+ component = &instance->component[instance->component_idx];
-+
-+ ret = create_component(instance, component, name);
-+ if (ret < 0)
-+ goto unlock;
-+
-+ /* ports info needs gathering */
-+ component->control.type = MMAL_PORT_TYPE_CONTROL;
-+ component->control.index = 0;
-+ component->control.component = component;
-+ spin_lock_init(&component->control.slock);
-+ INIT_LIST_HEAD(&component->control.buffers);
-+ ret = port_info_get(instance, &component->control);
-+ if (ret < 0)
-+ goto release_component;
-+
-+ for (idx = 0; idx < component->inputs; idx++) {
-+ component->input[idx].type = MMAL_PORT_TYPE_INPUT;
-+ component->input[idx].index = idx;
-+ component->input[idx].component = component;
-+ spin_lock_init(&component->input[idx].slock);
-+ INIT_LIST_HEAD(&component->input[idx].buffers);
-+ ret = port_info_get(instance, &component->input[idx]);
-+ if (ret < 0)
-+ goto release_component;
-+ }
-+
-+ for (idx = 0; idx < component->outputs; idx++) {
-+ component->output[idx].type = MMAL_PORT_TYPE_OUTPUT;
-+ component->output[idx].index = idx;
-+ component->output[idx].component = component;
-+ spin_lock_init(&component->output[idx].slock);
-+ INIT_LIST_HEAD(&component->output[idx].buffers);
-+ ret = port_info_get(instance, &component->output[idx]);
-+ if (ret < 0)
-+ goto release_component;
-+ }
-+
-+ for (idx = 0; idx < component->clocks; idx++) {
-+ component->clock[idx].type = MMAL_PORT_TYPE_CLOCK;
-+ component->clock[idx].index = idx;
-+ component->clock[idx].component = component;
-+ spin_lock_init(&component->clock[idx].slock);
-+ INIT_LIST_HEAD(&component->clock[idx].buffers);
-+ ret = port_info_get(instance, &component->clock[idx]);
-+ if (ret < 0)
-+ goto release_component;
-+ }
-+
-+ instance->component_idx++;
-+
-+ *component_out = component;
-+
-+ mutex_unlock(&instance->vchiq_mutex);
-+
-+ return 0;
-+
-+release_component:
-+ destroy_component(instance, component);
-+unlock:
-+ mutex_unlock(&instance->vchiq_mutex);
-+
-+ return ret;
-+}
-+
-+/*
-+ * cause a mmal component to be destroyed
-+ */
-+int vchiq_mmal_component_finalise(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_component *component)
-+{
-+ int ret;
-+
-+ if (mutex_lock_interruptible(&instance->vchiq_mutex))
-+ return -EINTR;
-+
-+ if (component->enabled)
-+ ret = disable_component(instance, component);
-+
-+ ret = destroy_component(instance, component);
-+
-+ mutex_unlock(&instance->vchiq_mutex);
-+
-+ return ret;
-+}
-+
-+/*
-+ * cause a mmal component to be enabled
-+ */
-+int vchiq_mmal_component_enable(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_component *component)
-+{
-+ int ret;
-+
-+ if (mutex_lock_interruptible(&instance->vchiq_mutex))
-+ return -EINTR;
-+
-+ if (component->enabled) {
-+ mutex_unlock(&instance->vchiq_mutex);
-+ return 0;
-+ }
-+
-+ ret = enable_component(instance, component);
-+ if (ret == 0)
-+ component->enabled = true;
-+
-+ mutex_unlock(&instance->vchiq_mutex);
-+
-+ return ret;
-+}
-+
-+/*
-+ * cause a mmal component to be enabled
-+ */
-+int vchiq_mmal_component_disable(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_component *component)
-+{
-+ int ret;
-+
-+ if (mutex_lock_interruptible(&instance->vchiq_mutex))
-+ return -EINTR;
-+
-+ if (!component->enabled) {
-+ mutex_unlock(&instance->vchiq_mutex);
-+ return 0;
-+ }
-+
-+ ret = disable_component(instance, component);
-+ if (ret == 0)
-+ component->enabled = false;
-+
-+ mutex_unlock(&instance->vchiq_mutex);
-+
-+ return ret;
-+}
-+
-+int vchiq_mmal_version(struct vchiq_mmal_instance *instance,
-+ u32 *major_out, u32 *minor_out)
-+{
-+ int ret;
-+
-+ if (mutex_lock_interruptible(&instance->vchiq_mutex))
-+ return -EINTR;
-+
-+ ret = get_version(instance, major_out, minor_out);
-+
-+ mutex_unlock(&instance->vchiq_mutex);
-+
-+ return ret;
-+}
-+
-+int vchiq_mmal_finalise(struct vchiq_mmal_instance *instance)
-+{
-+ int status = 0;
-+
-+ if (instance == NULL)
-+ return -EINVAL;
-+
-+ if (mutex_lock_interruptible(&instance->vchiq_mutex))
-+ return -EINTR;
-+
-+ vchi_service_use(instance->handle);
-+
-+ status = vchi_service_close(instance->handle);
-+ if (status != 0)
-+ pr_err("mmal-vchiq: VCHIQ close failed");
-+
-+ mutex_unlock(&instance->vchiq_mutex);
-+
-+ vfree(instance->bulk_scratch);
-+
-+ kfree(instance);
-+
-+ return status;
-+}
-+
-+int vchiq_mmal_init(struct vchiq_mmal_instance **out_instance)
-+{
-+ int status;
-+ struct vchiq_mmal_instance *instance;
-+ static VCHI_CONNECTION_T *vchi_connection;
-+ static VCHI_INSTANCE_T vchi_instance;
-+ SERVICE_CREATION_T params = {
-+ VCHI_VERSION_EX(VC_MMAL_VER, VC_MMAL_MIN_VER),
-+ VC_MMAL_SERVER_NAME,
-+ vchi_connection,
-+ 0, /* rx fifo size (unused) */
-+ 0, /* tx fifo size (unused) */
-+ service_callback,
-+ NULL, /* service callback parameter */
-+ 1, /* unaligned bulk receives */
-+ 1, /* unaligned bulk transmits */
-+ 0 /* want crc check on bulk transfers */
-+ };
-+
-+ /* compile time checks to ensure structure size as they are
-+ * directly (de)serialised from memory.
-+ */
-+
-+ /* ensure the header structure has packed to the correct size */
-+ BUILD_BUG_ON(sizeof(struct mmal_msg_header) != 24);
-+
-+ /* ensure message structure does not exceed maximum length */
-+ BUILD_BUG_ON(sizeof(struct mmal_msg) > MMAL_MSG_MAX_SIZE);
-+
-+ /* mmal port struct is correct size */
-+ BUILD_BUG_ON(sizeof(struct mmal_port) != 64);
-+
-+ /* create a vchi instance */
-+ status = vchi_initialise(&vchi_instance);
-+ if (status) {
-+ pr_err("Failed to initialise VCHI instance (status=%d)\n",
-+ status);
-+ return -EIO;
-+ }
-+
-+ status = vchi_connect(NULL, 0, vchi_instance);
-+ if (status) {
-+ pr_err("Failed to connect VCHI instance (status=%d)\n", status);
-+ return -EIO;
-+ }
-+
-+ instance = kmalloc(sizeof(*instance), GFP_KERNEL);
-+ memset(instance, 0, sizeof(*instance));
-+
-+ mutex_init(&instance->vchiq_mutex);
-+ mutex_init(&instance->bulk_mutex);
-+
-+ instance->bulk_scratch = vmalloc(PAGE_SIZE);
-+
-+ params.callback_param = instance;
-+
-+ status = vchi_service_open(vchi_instance, ¶ms, &instance->handle);
-+ if (status) {
-+ pr_err("Failed to open VCHI service connection (status=%d)\n",
-+ status);
-+ goto err_close_services;
-+ }
-+
-+ vchi_service_release(instance->handle);
-+
-+ *out_instance = instance;
-+
-+ return 0;
-+
-+err_close_services:
-+
-+ vchi_service_close(instance->handle);
-+ vfree(instance->bulk_scratch);
-+ kfree(instance);
-+ return -ENODEV;
-+}
---- /dev/null
-+++ b/drivers/media/platform/bcm2835/mmal-vchiq.h
-@@ -0,0 +1,178 @@
-+/*
-+ * Broadcom BM2835 V4L2 driver
-+ *
-+ * Copyright © 2013 Raspberry Pi (Trading) Ltd.
-+ *
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License. See the file COPYING in the main directory of this archive
-+ * for more details.
-+ *
-+ * Authors: Vincent Sanders <vincent.sanders at collabora.co.uk>
-+ * Dave Stevenson <dsteve at broadcom.com>
-+ * Simon Mellor <simellor at broadcom.com>
-+ * Luke Diamand <luked at broadcom.com>
-+ *
-+ * MMAL interface to VCHIQ message passing
-+ */
-+
-+#ifndef MMAL_VCHIQ_H
-+#define MMAL_VCHIQ_H
-+
-+#include "mmal-msg-format.h"
-+
-+#define MAX_PORT_COUNT 4
-+
-+/* Maximum size of the format extradata. */
-+#define MMAL_FORMAT_EXTRADATA_MAX_SIZE 128
-+
-+struct vchiq_mmal_instance;
-+
-+enum vchiq_mmal_es_type {
-+ MMAL_ES_TYPE_UNKNOWN, /**< Unknown elementary stream type */
-+ MMAL_ES_TYPE_CONTROL, /**< Elementary stream of control commands */
-+ MMAL_ES_TYPE_AUDIO, /**< Audio elementary stream */
-+ MMAL_ES_TYPE_VIDEO, /**< Video elementary stream */
-+ MMAL_ES_TYPE_SUBPICTURE /**< Sub-picture elementary stream */
-+};
-+
-+/* rectangle, used lots so it gets its own struct */
-+struct vchiq_mmal_rect {
-+ s32 x;
-+ s32 y;
-+ s32 width;
-+ s32 height;
-+};
-+
-+struct vchiq_mmal_port_buffer {
-+ unsigned int num; /* number of buffers */
-+ u32 size; /* size of buffers */
-+ u32 alignment; /* alignment of buffers */
-+};
-+
-+struct vchiq_mmal_port;
-+
-+typedef void (*vchiq_mmal_buffer_cb)(
-+ struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *port,
-+ int status, struct mmal_buffer *buffer,
-+ unsigned long length, u32 mmal_flags, s64 dts, s64 pts);
-+
-+struct vchiq_mmal_port {
-+ bool enabled;
-+ u32 handle;
-+ u32 type; /* port type, cached to use on port info set */
-+ u32 index; /* port index, cached to use on port info set */
-+
-+ /* component port belongs to, allows simple deref */
-+ struct vchiq_mmal_component *component;
-+
-+ struct vchiq_mmal_port *connected; /* port conencted to */
-+
-+ /* buffer info */
-+ struct vchiq_mmal_port_buffer minimum_buffer;
-+ struct vchiq_mmal_port_buffer recommended_buffer;
-+ struct vchiq_mmal_port_buffer current_buffer;
-+
-+ /* stream format */
-+ struct mmal_es_format format;
-+ /* elementry stream format */
-+ union mmal_es_specific_format es;
-+
-+ /* data buffers to fill */
-+ struct list_head buffers;
-+ /* lock to serialise adding and removing buffers from list */
-+ spinlock_t slock;
-+ /* count of how many buffer header refils have failed because
-+ * there was no buffer to satisfy them
-+ */
-+ int buffer_underflow;
-+ /* callback on buffer completion */
-+ vchiq_mmal_buffer_cb buffer_cb;
-+ /* callback context */
-+ void *cb_ctx;
-+};
-+
-+struct vchiq_mmal_component {
-+ bool enabled;
-+ u32 handle; /* VideoCore handle for component */
-+ u32 inputs; /* Number of input ports */
-+ u32 outputs; /* Number of output ports */
-+ u32 clocks; /* Number of clock ports */
-+ struct vchiq_mmal_port control; /* control port */
-+ struct vchiq_mmal_port input[MAX_PORT_COUNT]; /* input ports */
-+ struct vchiq_mmal_port output[MAX_PORT_COUNT]; /* output ports */
-+ struct vchiq_mmal_port clock[MAX_PORT_COUNT]; /* clock ports */
-+};
-+
-+
-+int vchiq_mmal_init(struct vchiq_mmal_instance **out_instance);
-+int vchiq_mmal_finalise(struct vchiq_mmal_instance *instance);
-+
-+/* Initialise a mmal component and its ports
-+*
-+*/
-+int vchiq_mmal_component_init(
-+ struct vchiq_mmal_instance *instance,
-+ const char *name,
-+ struct vchiq_mmal_component **component_out);
-+
-+int vchiq_mmal_component_finalise(
-+ struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_component *component);
-+
-+int vchiq_mmal_component_enable(
-+ struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_component *component);
-+
-+int vchiq_mmal_component_disable(
-+ struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_component *component);
-+
-+
-+
-+/* enable a mmal port
-+ *
-+ * enables a port and if a buffer callback provided enque buffer
-+ * headers as apropriate for the port.
-+ */
-+int vchiq_mmal_port_enable(
-+ struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *port,
-+ vchiq_mmal_buffer_cb buffer_cb);
-+
-+/* disable a port
-+ *
-+ * disable a port will dequeue any pending buffers
-+ */
-+int vchiq_mmal_port_disable(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *port);
-+
-+
-+int vchiq_mmal_port_parameter_set(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *port,
-+ u32 parameter,
-+ void *value,
-+ u32 value_size);
-+
-+int vchiq_mmal_port_parameter_get(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *port,
-+ u32 parameter,
-+ void *value,
-+ u32 *value_size);
-+
-+int vchiq_mmal_port_set_format(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *port);
-+
-+int vchiq_mmal_port_connect_tunnel(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *src,
-+ struct vchiq_mmal_port *dst);
-+
-+int vchiq_mmal_version(struct vchiq_mmal_instance *instance,
-+ u32 *major_out,
-+ u32 *minor_out);
-+
-+int vchiq_mmal_submit_buffer(struct vchiq_mmal_instance *instance,
-+ struct vchiq_mmal_port *port,
-+ struct mmal_buffer *buf);
-+
-+#endif /* MMAL_VCHIQ_H */
diff --git a/target/linux/brcm2708/patches-4.4/0049-scripts-Add-mkknlimg-and-knlinfo-scripts-from-tools-.patch b/target/linux/brcm2708/patches-4.4/0049-scripts-Add-mkknlimg-and-knlinfo-scripts-from-tools-.patch
deleted file mode 100644
index 3638370..0000000
--- a/target/linux/brcm2708/patches-4.4/0049-scripts-Add-mkknlimg-and-knlinfo-scripts-from-tools-.patch
+++ /dev/null
@@ -1,460 +0,0 @@
-From 3703cda20110756a6531a570a4e52b2b42d99bf9 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 11 May 2015 09:00:42 +0100
-Subject: [PATCH] scripts: Add mkknlimg and knlinfo scripts from tools repo
-
-The Raspberry Pi firmware looks for a trailer on the kernel image to
-determine whether it was compiled with Device Tree support enabled.
-If the firmware finds a kernel without this trailer, or which has a
-trailer indicating that it isn't DT-capable, it disables DT support
-and reverts to using ATAGs.
-
-The mkknlimg utility adds that trailer, having first analysed the
-image to look for signs of DT support and the kernel version string.
-
-knlinfo displays the contents of the trailer in the given kernel image.
-
-scripts/mkknlimg: Add support for ARCH_BCM2835
-
-Add a new trailer field indicating whether this is an ARCH_BCM2835
-build, as opposed to MACH_BCM2708/9. If the loader finds this flag
-is set it changes the default base dtb file name from bcm270x...
-to bcm283y...
-
-Also update knlinfo to show the status of the field.
-
-scripts/mkknlimg: Improve ARCH_BCM2835 detection
-
-The board support code contains sufficient strings to be able to
-distinguish 2708 vs. 2835 builds, so remove the check for
-bcm2835-pm-wdt which could exist in either.
-
-Also, since the canned configuration is no longer built in (it's
-a module), remove the config string checking.
-
-See: https://github.com/raspberrypi/linux/issues/1157
----
- scripts/knlinfo | 168 ++++++++++++++++++++++++++++++++++++++
- scripts/mkknlimg | 244 +++++++++++++++++++++++++++++++++++++++++++++++++++++++
- 2 files changed, 412 insertions(+)
- create mode 100755 scripts/knlinfo
- create mode 100755 scripts/mkknlimg
-
---- /dev/null
-+++ b/scripts/knlinfo
-@@ -0,0 +1,168 @@
-+#!/usr/bin/env perl
-+# ----------------------------------------------------------------------
-+# knlinfo by Phil Elwell for Raspberry Pi
-+#
-+# (c) 2014,2015 Raspberry Pi (Trading) Limited <info at raspberrypi.org>
-+#
-+# Licensed under the terms of the GNU General Public License.
-+# ----------------------------------------------------------------------
-+
-+use strict;
-+use integer;
-+
-+use Fcntl ":seek";
-+
-+my $trailer_magic = 'RPTL';
-+
-+my %atom_formats =
-+(
-+ 'DTOK' => \&format_bool,
-+ 'KVer' => \&format_string,
-+ '283x' => \&format_bool,
-+);
-+
-+if (@ARGV != 1)
-+{
-+ print ("Usage: knlinfo <kernel image>\n");
-+ exit(1);
-+}
-+
-+my $kernel_file = $ARGV[0];
-+
-+
-+my ($atoms, $pos) = read_trailer($kernel_file);
-+
-+exit(1) if (!$atoms);
-+
-+printf("Kernel trailer found at %d/0x%x:\n", $pos, $pos);
-+
-+foreach my $atom (@$atoms)
-+{
-+ printf(" %s: %s\n", $atom->[0], format_atom($atom));
-+}
-+
-+exit(0);
-+
-+sub read_trailer
-+{
-+ my ($kernel_file) = @_;
-+ my $fh;
-+
-+ if (!open($fh, '<', $kernel_file))
-+ {
-+ print ("* Failed to open '$kernel_file'\n");
-+ return undef;
-+ }
-+
-+ if (!seek($fh, -12, SEEK_END))
-+ {
-+ print ("* seek error in '$kernel_file'\n");
-+ return undef;
-+ }
-+
-+ my $last_bytes;
-+ sysread($fh, $last_bytes, 12);
-+
-+ my ($trailer_len, $data_len, $magic) = unpack('VVa4', $last_bytes);
-+
-+ if (($magic ne $trailer_magic) || ($data_len != 4))
-+ {
-+ print ("* no trailer\n");
-+ return undef;
-+ }
-+ if (!seek($fh, -12, SEEK_END))
-+ {
-+ print ("* seek error in '$kernel_file'\n");
-+ return undef;
-+ }
-+
-+ $trailer_len -= 12;
-+
-+ while ($trailer_len > 0)
-+ {
-+ if ($trailer_len < 8)
-+ {
-+ print ("* truncated atom header in trailer\n");
-+ return undef;
-+ }
-+ if (!seek($fh, -8, SEEK_CUR))
-+ {
-+ print ("* seek error in '$kernel_file'\n");
-+ return undef;
-+ }
-+ $trailer_len -= 8;
-+
-+ my $atom_hdr;
-+ sysread($fh, $atom_hdr, 8);
-+ my ($atom_len, $atom_type) = unpack('Va4', $atom_hdr);
-+
-+ if ($trailer_len < $atom_len)
-+ {
-+ print ("* truncated atom data in trailer\n");
-+ return undef;
-+ }
-+
-+ my $rounded_len = (($atom_len + 3) & ~3);
-+ if (!seek($fh, -(8 + $rounded_len), SEEK_CUR))
-+ {
-+ print ("* seek error in '$kernel_file'\n");
-+ return undef;
-+ }
-+ $trailer_len -= $rounded_len;
-+
-+ my $atom_data;
-+ sysread($fh, $atom_data, $atom_len);
-+
-+ if (!seek($fh, -$atom_len, SEEK_CUR))
-+ {
-+ print ("* seek error in '$kernel_file'\n");
-+ return undef;
-+ }
-+
-+ push @$atoms, [ $atom_type, $atom_data ];
-+ }
-+
-+ if (($$atoms[-1][0] eq "\x00\x00\x00\x00") &&
-+ ($$atoms[-1][1] eq ""))
-+ {
-+ pop @$atoms;
-+ }
-+ else
-+ {
-+ print ("* end marker missing from trailer\n");
-+ }
-+
-+ return ($atoms, tell($fh));
-+}
-+
-+sub format_atom
-+{
-+ my ($atom) = @_;
-+
-+ my $format_func = $atom_formats{$atom->[0]} || \&format_hex;
-+ return $format_func->($atom->[1]);
-+}
-+
-+sub format_bool
-+{
-+ my ($data) = @_;
-+ return unpack('V', $data) ? 'true' : 'false';
-+}
-+
-+sub format_int
-+{
-+ my ($data) = @_;
-+ return unpack('V', $data);
-+}
-+
-+sub format_string
-+{
-+ my ($data) = @_;
-+ return '"'.$data.'"';
-+}
-+
-+sub format_hex
-+{
-+ my ($data) = @_;
-+ return unpack('H*', $data);
-+}
---- /dev/null
-+++ b/scripts/mkknlimg
-@@ -0,0 +1,244 @@
-+#!/usr/bin/env perl
-+# ----------------------------------------------------------------------
-+# mkknlimg by Phil Elwell for Raspberry Pi
-+# based on extract-ikconfig by Dick Streefland
-+#
-+# (c) 2009,2010 Dick Streefland <dick at streefland.net>
-+# (c) 2014,2015 Raspberry Pi (Trading) Limited <info at raspberrypi.org>
-+#
-+# Licensed under the terms of the GNU General Public License.
-+# ----------------------------------------------------------------------
-+
-+use strict;
-+use warnings;
-+use integer;
-+
-+my $trailer_magic = 'RPTL';
-+
-+my $tmpfile1 = "/tmp/mkknlimg_$$.1";
-+my $tmpfile2 = "/tmp/mkknlimg_$$.2";
-+
-+my $dtok = 0;
-+my $is_283x = 0;
-+
-+while (@ARGV && ($ARGV[0] =~ /^-/))
-+{
-+ my $arg = shift(@ARGV);
-+ if ($arg eq '--dtok')
-+ {
-+ $dtok = 1;
-+ }
-+ elsif ($arg eq '--283x')
-+ {
-+ $is_283x = 1;
-+ }
-+ else
-+ {
-+ print ("* Unknown option '$arg'\n");
-+ usage();
-+ }
-+}
-+
-+usage() if (@ARGV != 2);
-+
-+my $kernel_file = $ARGV[0];
-+my $out_file = $ARGV[1];
-+
-+if (! -r $kernel_file)
-+{
-+ print ("* File '$kernel_file' not found\n");
-+ usage();
-+}
-+
-+my @wanted_strings =
-+(
-+ 'bcm2708_fb',
-+ 'brcm,bcm2835-mmc',
-+ 'brcm,bcm2835-sdhost',
-+ 'brcm,bcm2708-pinctrl',
-+ 'brcm,bcm2835-gpio',
-+ 'brcm,bcm2835',
-+ 'brcm,bcm2836'
-+);
-+
-+my $res = try_extract($kernel_file, $tmpfile1);
-+$res = try_decompress('\037\213\010', 'xy', 'gunzip', 0,
-+ $kernel_file, $tmpfile1, $tmpfile2) if (!$res);
-+$res = try_decompress('\3757zXZ\000', 'abcde', 'unxz --single-stream', -1,
-+ $kernel_file, $tmpfile1, $tmpfile2) if (!$res);
-+$res = try_decompress('BZh', 'xy', 'bunzip2', 0,
-+ $kernel_file, $tmpfile1, $tmpfile2) if (!$res);
-+$res = try_decompress('\135\0\0\0', 'xxx', 'unlzma', 0,
-+ $kernel_file, $tmpfile1, $tmpfile2) if (!$res);
-+$res = try_decompress('\211\114\132', 'xy', 'lzop -d', 0,
-+ $kernel_file, $tmpfile1, $tmpfile2) if (!$res);
-+$res = try_decompress('\002\041\114\030', 'xy', 'lz4 -d', 1,
-+ $kernel_file, $tmpfile1, $tmpfile2) if (!$res);
-+
-+my $append_trailer;
-+my $trailer;
-+my $kver = '?';
-+
-+$append_trailer = $dtok;
-+
-+if ($res)
-+{
-+ $kver = $res->{''} || '?';
-+ print("Version: $kver\n");
-+
-+ $append_trailer = $dtok;
-+ if (!$dtok)
-+ {
-+ if (config_bool($res, 'bcm2708_fb') ||
-+ config_bool($res, 'brcm,bcm2835-mmc') ||
-+ config_bool($res, 'brcm,bcm2835-sdhost'))
-+ {
-+ $dtok ||= config_bool($res, 'brcm,bcm2708-pinctrl');
-+ $dtok ||= config_bool($res, 'brcm,bcm2835-gpio');
-+ $is_283x ||= config_bool($res, 'brcm,bcm2835');
-+ $is_283x ||= config_bool($res, 'brcm,bcm2836');
-+ $dtok ||= $is_283x;
-+ $append_trailer = 1;
-+ }
-+ else
-+ {
-+ print ("* This doesn't look like a Raspberry Pi kernel. In pass-through mode.\n");
-+ }
-+ }
-+}
-+elsif (!$dtok)
-+{
-+ print ("* Is this a valid kernel? In pass-through mode.\n");
-+}
-+
-+if ($append_trailer)
-+{
-+ printf("DT: %s\n", $dtok ? "y" : "n");
-+ printf("283x: %s\n", $is_283x ? "y" : "n");
-+
-+ my @atoms;
-+
-+ push @atoms, [ $trailer_magic, pack('V', 0) ];
-+ push @atoms, [ 'KVer', $kver ];
-+ push @atoms, [ 'DTOK', pack('V', $dtok) ];
-+ push @atoms, [ '283x', pack('V', $is_283x) ];
-+
-+ $trailer = pack_trailer(\@atoms);
-+ $atoms[0]->[1] = pack('V', length($trailer));
-+
-+ $trailer = pack_trailer(\@atoms);
-+}
-+
-+my $ofh;
-+my $total_len = 0;
-+
-+if ($out_file eq $kernel_file)
-+{
-+ die "* Failed to open '$out_file' for append\n"
-+ if (!open($ofh, '>>', $out_file));
-+ $total_len = tell($ofh);
-+}
-+else
-+{
-+ die "* Failed to open '$kernel_file'\n"
-+ if (!open(my $ifh, '<', $kernel_file));
-+ die "* Failed to create '$out_file'\n"
-+ if (!open($ofh, '>', $out_file));
-+
-+ my $copybuf;
-+ while (1)
-+ {
-+ my $bytes = sysread($ifh, $copybuf, 64*1024);
-+ last if (!$bytes);
-+ syswrite($ofh, $copybuf, $bytes);
-+ $total_len += $bytes;
-+ }
-+ close($ifh);
-+}
-+
-+if ($trailer)
-+{
-+ # Pad to word-alignment
-+ syswrite($ofh, "\x000\x000\x000", (-$total_len & 0x3));
-+ syswrite($ofh, $trailer);
-+}
-+
-+close($ofh);
-+
-+exit($trailer ? 0 : 1);
-+
-+END {
-+ unlink($tmpfile1) if ($tmpfile1);
-+ unlink($tmpfile2) if ($tmpfile2);
-+}
-+
-+
-+sub usage
-+{
-+ print ("Usage: mkknlimg [--dtok] [--283x] <vmlinux|zImage|bzImage> <outfile>\n");
-+ exit(1);
-+}
-+
-+sub try_extract
-+{
-+ my ($knl, $tmp) = @_;
-+
-+ my $ver = `strings "$knl" | grep -a -E "^Linux version [1-9]"`;
-+
-+ return undef if (!$ver);
-+
-+ chomp($ver);
-+
-+ my $res = { ''=>$ver };
-+ my $string_pattern = '^('.join('|', @wanted_strings).')$';
-+
-+ my @matches = `strings \"$knl\" | grep -E \"$string_pattern\"`;
-+ foreach my $match (@matches)
-+ {
-+ chomp($match);
-+ $res->{$match} = 1;
-+ }
-+
-+ return $res;
-+}
-+
-+
-+sub try_decompress
-+{
-+ my ($magic, $subst, $zcat, $idx, $knl, $tmp1, $tmp2) = @_;
-+
-+ my $pos = `tr "$magic\n$subst" "\n$subst=" < "$knl" | grep -abo "^$subst"`;
-+ if ($pos)
-+ {
-+ chomp($pos);
-+ $pos = (split(/[\r\n]+/, $pos))[$idx];
-+ return undef if (!defined($pos));
-+ $pos =~ s/:.*[\r\n]*$//s;
-+ my $cmd = "tail -c+$pos \"$knl\" | $zcat > $tmp2 2> /dev/null";
-+ my $err = (system($cmd) >> 8);
-+ return undef if (($err != 0) && ($err != 2));
-+
-+ return try_extract($tmp2, $tmp1);
-+ }
-+
-+ return undef;
-+}
-+
-+sub pack_trailer
-+{
-+ my ($atoms) = @_;
-+ my $trailer = pack('VV', 0, 0);
-+ for (my $i = $#$atoms; $i>=0; $i--)
-+ {
-+ my $atom = $atoms->[$i];
-+ $trailer .= pack('a*x!4Va4', $atom->[1], length($atom->[1]), $atom->[0]);
-+ }
-+ return $trailer;
-+}
-+
-+sub config_bool
-+{
-+ my ($configs, $wanted) = @_;
-+ my $val = $configs->{$wanted} || 'n';
-+ return (($val eq 'y') || ($val eq '1'));
-+}
diff --git a/target/linux/brcm2708/patches-4.4/0050-fdt-Add-support-for-the-CONFIG_CMDLINE_EXTEND-option.patch b/target/linux/brcm2708/patches-4.4/0050-fdt-Add-support-for-the-CONFIG_CMDLINE_EXTEND-option.patch
deleted file mode 100644
index 2a7a1b4..0000000
--- a/target/linux/brcm2708/patches-4.4/0050-fdt-Add-support-for-the-CONFIG_CMDLINE_EXTEND-option.patch
+++ /dev/null
@@ -1,55 +0,0 @@
-From 74d27f374a1df3d1652dccaea3d7c1a0344215ed Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 5 Dec 2014 17:26:26 +0000
-Subject: [PATCH] fdt: Add support for the CONFIG_CMDLINE_EXTEND option
-
----
- drivers/of/fdt.c | 29 ++++++++++++++++++++++++-----
- 1 file changed, 24 insertions(+), 5 deletions(-)
-
---- a/drivers/of/fdt.c
-+++ b/drivers/of/fdt.c
-@@ -957,19 +957,38 @@ int __init early_init_dt_scan_chosen(uns
-
- /* Retrieve command line */
- p = of_get_flat_dt_prop(node, "bootargs", &l);
-- if (p != NULL && l > 0)
-- strlcpy(data, p, min((int)l, COMMAND_LINE_SIZE));
-
- /*
- * CONFIG_CMDLINE is meant to be a default in case nothing else
- * managed to set the command line, unless CONFIG_CMDLINE_FORCE
- * is set in which case we override whatever was found earlier.
-+ *
-+ * However, it can be useful to be able to treat the default as
-+ * a starting point to be extended using CONFIG_CMDLINE_EXTEND.
- */
-+ ((char *)data)[0] = '\0';
-+
- #ifdef CONFIG_CMDLINE
--#ifndef CONFIG_CMDLINE_FORCE
-- if (!((char *)data)[0])
-+ strlcpy(data, CONFIG_CMDLINE, COMMAND_LINE_SIZE);
-+
-+ if (p != NULL && l > 0) {
-+#if defined(CONFIG_CMDLINE_EXTEND)
-+ int len = strlen(data);
-+ if (len > 0) {
-+ strlcat(data, " ", COMMAND_LINE_SIZE);
-+ len++;
-+ }
-+ strlcpy((char *)data + len, p, min((int)l, COMMAND_LINE_SIZE - len));
-+#elif defined(CONFIG_CMDLINE_FORCE)
-+ pr_warning("Ignoring bootargs property (using the default kernel command line)\n");
-+#else
-+ /* Neither extend nor force - just override */
-+ strlcpy(data, p, min((int)l, COMMAND_LINE_SIZE));
- #endif
-- strlcpy(data, CONFIG_CMDLINE, COMMAND_LINE_SIZE);
-+ }
-+#else /* CONFIG_CMDLINE */
-+ if (p != NULL && l > 0)
-+ strlcpy(data, p, min((int)l, COMMAND_LINE_SIZE));
- #endif /* CONFIG_CMDLINE */
-
- pr_debug("Command line is: %s\n", (char*)data);
diff --git a/target/linux/brcm2708/patches-4.4/0051-BCM2708-Add-core-Device-Tree-support.patch b/target/linux/brcm2708/patches-4.4/0051-BCM2708-Add-core-Device-Tree-support.patch
deleted file mode 100644
index 996833b..0000000
--- a/target/linux/brcm2708/patches-4.4/0051-BCM2708-Add-core-Device-Tree-support.patch
+++ /dev/null
@@ -1,4564 +0,0 @@
-From 136ea0d26db2d172ce9ab36da7f75f97dde6abde Mon Sep 17 00:00:00 2001
-From: notro <notro at tronnes.org>
-Date: Wed, 9 Jul 2014 14:46:08 +0200
-Subject: [PATCH] BCM2708: Add core Device Tree support
-
-Add the bare minimum needed to boot BCM2708 from a Device Tree.
-
-Signed-off-by: Noralf Tronnes <notro at tronnes.org>
-
-BCM2708: DT: change 'axi' nodename to 'soc'
-
-Change DT node named 'axi' to 'soc' so it matches ARCH_BCM2835.
-The VC4 bootloader fills in certain properties in the 'axi' subtree,
-but since this is part of an upstreaming effort, the name is changed.
-
-Signed-off-by: Noralf Tronnes notro at tronnes.org
-
-BCM2708_DT: Correct length of the peripheral space
-
-Use dts-dirs feature for overlays.
-
-The kernel makefiles have a dts-dirs target that is for vendor subdirectories.
-
-Using this fixes the install_dtbs target, which previously did not install the overlays.
-
-BCM270X_DT: configure I2S DMA channels
-
-Signed-off-by: Matthias Reichl <hias at horus.com>
-
-BCM270X_DT: switch to bcm2835-i2s
-
-I2S soundcard drivers with proper devicetree support (i.e. not linking
-to the cpu_dai/platform via name but to cpu/platform via of_node)
-will work out of the box without any modifications.
-
-When the kernel is compiled without devicetree support the platform
-code will instantiate the bcm2708-i2s driver and I2S soundcard drivers
-will link to it via name, as before.
-
-Signed-off-by: Matthias Reichl <hias at horus.com>
-
-SDIO-overlay: add poll_once-boolean parameter
-
-Add paramter to toggle sdio-device-polling
-done every second or once at boot-time.
-
-Signed-off-by: Patrick Boettcher <patrick.boettcher at posteo.de>
-
-BCM270X_DT: Make mmc overlay compatible with current firmware
-
-The original DT overlay logic followed a merge-then-patch procedure,
-i.e. parameters are applied to the loaded overlay before the overlay
-is merged into the base DTB. This sequence has been changed to
-patch-then-merge, in order to support parameterised node names, and
-to protect against bad overlays. As a result, overrides (parameters)
-must only target labels in the overlay, but the overlay can obviously target nodes in the base DTB.
-
-mmc-overlay.dts (that switches back to the original mmc sdcard
-driver) is the only overlay violating that rule, and this patch
-fixes it.
-
-bcm270x_dt: Use the sdhost MMC controller by default
-
-The "mmc" overlay reverts to using the other controller.
-
-squash: Add cprman to dt
-
-BCM270X_DT: Use clk_core for I2C interfaces
----
- arch/arm/boot/dts/Makefile | 30 +
- arch/arm/boot/dts/bcm2708-rpi-b-plus.dts | 145 +++++
- arch/arm/boot/dts/bcm2708-rpi-b.dts | 135 +++++
- arch/arm/boot/dts/bcm2708-rpi-cm.dts | 102 ++++
- arch/arm/boot/dts/bcm2708-rpi-cm.dtsi | 40 ++
- arch/arm/boot/dts/bcm2708.dtsi | 40 ++
- arch/arm/boot/dts/bcm2708_common.dtsi | 347 +++++++++++
- arch/arm/boot/dts/bcm2709-rpi-2-b.dts | 145 +++++
- arch/arm/boot/dts/bcm2709.dtsi | 102 ++++
- arch/arm/boot/dts/bcm2835-rpi-cm.dts | 93 +++
- arch/arm/boot/dts/bcm2835-rpi-cm.dtsi | 30 +
- arch/arm/boot/dts/overlays/Makefile | 69 +++
- arch/arm/boot/dts/overlays/README | 648 +++++++++++++++++++++
- arch/arm/boot/dts/overlays/ads7846-overlay.dts | 83 +++
- .../dts/overlays/bmp085_i2c-sensor-overlay.dts | 23 +
- arch/arm/boot/dts/overlays/dht11-overlay.dts | 39 ++
- arch/arm/boot/dts/overlays/enc28j60-overlay.dts | 50 ++
- .../boot/dts/overlays/gpio-poweroff-overlay.dts | 34 ++
- .../boot/dts/overlays/hifiberry-amp-overlay.dts | 39 ++
- .../boot/dts/overlays/hifiberry-dac-overlay.dts | 34 ++
- .../dts/overlays/hifiberry-dacplus-overlay.dts | 39 ++
- .../boot/dts/overlays/hifiberry-digi-overlay.dts | 39 ++
- arch/arm/boot/dts/overlays/hy28a-overlay.dts | 87 +++
- arch/arm/boot/dts/overlays/hy28b-overlay.dts | 142 +++++
- arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts | 55 ++
- arch/arm/boot/dts/overlays/i2s-mmap-overlay.dts | 13 +
- arch/arm/boot/dts/overlays/iqaudio-dac-overlay.dts | 39 ++
- .../boot/dts/overlays/iqaudio-dacplus-overlay.dts | 39 ++
- arch/arm/boot/dts/overlays/lirc-rpi-overlay.dts | 57 ++
- .../arm/boot/dts/overlays/mcp2515-can0-overlay.dts | 69 +++
- .../arm/boot/dts/overlays/mcp2515-can1-overlay.dts | 69 +++
- arch/arm/boot/dts/overlays/mmc-overlay.dts | 39 ++
- arch/arm/boot/dts/overlays/mz61581-overlay.dts | 111 ++++
- arch/arm/boot/dts/overlays/piscreen-overlay.dts | 96 +++
- .../dts/overlays/pitft28-resistive-overlay.dts | 115 ++++
- arch/arm/boot/dts/overlays/pps-gpio-overlay.dts | 34 ++
- arch/arm/boot/dts/overlays/pwm-2chan-overlay.dts | 46 ++
- arch/arm/boot/dts/overlays/pwm-overlay.dts | 42 ++
- arch/arm/boot/dts/overlays/raspidac3-overlay.dts | 45 ++
- arch/arm/boot/dts/overlays/rpi-dac-overlay.dts | 34 ++
- arch/arm/boot/dts/overlays/rpi-display-overlay.dts | 82 +++
- arch/arm/boot/dts/overlays/rpi-ft5406-overlay.dts | 17 +
- arch/arm/boot/dts/overlays/rpi-proto-overlay.dts | 39 ++
- arch/arm/boot/dts/overlays/rpi-sense-overlay.dts | 47 ++
- arch/arm/boot/dts/overlays/sdhost-overlay.dts | 29 +
- arch/arm/boot/dts/overlays/sdio-overlay.dts | 32 +
- arch/arm/boot/dts/overlays/smi-dev-overlay.dts | 18 +
- arch/arm/boot/dts/overlays/smi-nand-overlay.dts | 69 +++
- arch/arm/boot/dts/overlays/smi-overlay.dts | 37 ++
- .../boot/dts/overlays/spi-gpio35-39-overlay.dts | 31 +
- arch/arm/boot/dts/overlays/tinylcd35-overlay.dts | 216 +++++++
- arch/arm/boot/dts/overlays/uart1-overlay.dts | 38 ++
- arch/arm/boot/dts/overlays/vga666-overlay.dts | 30 +
- arch/arm/boot/dts/overlays/w1-gpio-overlay.dts | 39 ++
- .../boot/dts/overlays/w1-gpio-pullup-overlay.dts | 41 ++
- 55 files changed, 4203 insertions(+)
- create mode 100644 arch/arm/boot/dts/bcm2708-rpi-b-plus.dts
- create mode 100644 arch/arm/boot/dts/bcm2708-rpi-b.dts
- create mode 100755 arch/arm/boot/dts/bcm2708-rpi-cm.dts
- create mode 100644 arch/arm/boot/dts/bcm2708-rpi-cm.dtsi
- create mode 100644 arch/arm/boot/dts/bcm2708.dtsi
- create mode 100644 arch/arm/boot/dts/bcm2708_common.dtsi
- create mode 100644 arch/arm/boot/dts/bcm2709-rpi-2-b.dts
- create mode 100644 arch/arm/boot/dts/bcm2709.dtsi
- create mode 100644 arch/arm/boot/dts/bcm2835-rpi-cm.dts
- create mode 100644 arch/arm/boot/dts/bcm2835-rpi-cm.dtsi
- create mode 100644 arch/arm/boot/dts/overlays/Makefile
- create mode 100644 arch/arm/boot/dts/overlays/README
- create mode 100644 arch/arm/boot/dts/overlays/ads7846-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/bmp085_i2c-sensor-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/dht11-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/enc28j60-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/gpio-poweroff-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/hifiberry-amp-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/hifiberry-dac-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/hifiberry-dacplus-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/hifiberry-digi-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/hy28a-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/hy28b-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/i2s-mmap-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/iqaudio-dac-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/iqaudio-dacplus-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/lirc-rpi-overlay.dts
- create mode 100755 arch/arm/boot/dts/overlays/mcp2515-can0-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/mcp2515-can1-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/mmc-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/mz61581-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/piscreen-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/pitft28-resistive-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/pps-gpio-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/pwm-2chan-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/pwm-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/raspidac3-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/rpi-dac-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/rpi-display-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/rpi-ft5406-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/rpi-proto-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/rpi-sense-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/sdhost-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/sdio-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/smi-dev-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/smi-nand-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/smi-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/spi-gpio35-39-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/tinylcd35-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/uart1-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/vga666-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/w1-gpio-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/w1-gpio-pullup-overlay.dts
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -1,5 +1,25 @@
- ifeq ($(CONFIG_OF),y)
-
-+dtb-$(CONFIG_ARCH_BCM2708) += bcm2708-rpi-b.dtb
-+dtb-$(CONFIG_ARCH_BCM2708) += bcm2708-rpi-b-plus.dtb
-+dtb-$(CONFIG_ARCH_BCM2708) += bcm2708-rpi-cm.dtb
-+dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-cm.dtb
-+dtb-$(CONFIG_ARCH_BCM2709) += bcm2709-rpi-2-b.dtb
-+
-+# Raspberry Pi
-+ifeq ($(CONFIG_ARCH_BCM2708),y)
-+ RPI_DT_OVERLAYS=y
-+endif
-+ifeq ($(CONFIG_ARCH_BCM2709),y)
-+ RPI_DT_OVERLAYS=y
-+endif
-+ifeq ($(CONFIG_ARCH_BCM2835),y)
-+ RPI_DT_OVERLAYS=y
-+endif
-+ifeq ($(RPI_DT_OVERLAYS),y)
-+ dts-dirs += overlays
-+endif
-+
- dtb-$(CONFIG_ARCH_ALPINE) += \
- alpine-db.dtb
- dtb-$(CONFIG_MACH_ASM9260) += \
-@@ -777,10 +797,20 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
- mt8127-moose.dtb \
- mt8135-evbp1.dtb
- dtb-$(CONFIG_ARCH_ZX) += zx296702-ad1.dtb
-+
-+targets += dtbs dtbs_install
-+targets += $(dtb-y)
-+
- endif
-
- dtstree := $(srctree)/$(src)
- dtb-$(CONFIG_OF_ALL_DTBS) := $(patsubst $(dtstree)/%.dts,%.dtb, $(wildcard $(dtstree)/*.dts))
-
- always := $(dtb-y)
-+subdir-y := $(dts-dirs)
- clean-files := *.dtb
-+
-+# Enable fixups to support overlays on BCM2708 platforms
-+ifeq ($(RPI_DT_OVERLAYS),y)
-+ DTC_FLAGS ?= -@
-+endif
---- /dev/null
-+++ b/arch/arm/boot/dts/bcm2708-rpi-b-plus.dts
-@@ -0,0 +1,145 @@
-+/dts-v1/;
-+
-+#include "bcm2708.dtsi"
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+ model = "Raspberry Pi Model B+";
-+};
-+
-+&gpio {
-+ sdhost_pins: sdhost_pins {
-+ brcm,pins = <48 49 50 51 52 53>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+
-+ spi0_pins: spi0_pins {
-+ brcm,pins = <9 10 11>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+
-+ spi0_cs_pins: spi0_cs_pins {
-+ brcm,pins = <8 7>;
-+ brcm,function = <1>; /* output */
-+ };
-+
-+ i2c0_pins: i2c0 {
-+ brcm,pins = <0 1>;
-+ brcm,function = <4>;
-+ };
-+
-+ i2c1_pins: i2c1 {
-+ brcm,pins = <2 3>;
-+ brcm,function = <4>;
-+ };
-+
-+ i2s_pins: i2s {
-+ brcm,pins = <18 19 20 21>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+};
-+
-+&sdhost {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&sdhost_pins>;
-+ bus-width = <4>;
-+ status = "okay";
-+};
-+
-+&fb {
-+ status = "okay";
-+};
-+
-+&uart0 {
-+ status = "okay";
-+};
-+
-+&spi0 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
-+ cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
-+
-+ spidev at 0{
-+ compatible = "spidev";
-+ reg = <0>; /* CE0 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ };
-+
-+ spidev at 1{
-+ compatible = "spidev";
-+ reg = <1>; /* CE1 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ };
-+};
-+
-+&i2c0 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2c0_pins>;
-+ clock-frequency = <100000>;
-+};
-+
-+&i2c1 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2c1_pins>;
-+ clock-frequency = <100000>;
-+};
-+
-+&i2c2 {
-+ clock-frequency = <100000>;
-+};
-+
-+&i2s {
-+ #sound-dai-cells = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2s_pins>;
-+};
-+
-+&random {
-+ status = "okay";
-+};
-+
-+&leds {
-+ act_led: act {
-+ label = "led0";
-+ linux,default-trigger = "mmc0";
-+ gpios = <&gpio 47 0>;
-+ };
-+
-+ pwr_led: pwr {
-+ label = "led1";
-+ linux,default-trigger = "input";
-+ gpios = <&gpio 35 0>;
-+ };
-+};
-+
-+/ {
-+ __overrides__ {
-+ uart0 = <&uart0>,"status";
-+ uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
-+ i2s = <&i2s>,"status";
-+ spi = <&spi0>,"status";
-+ i2c0 = <&i2c0>,"status";
-+ i2c1 = <&i2c1>,"status";
-+ i2c2_iknowwhatimdoing = <&i2c2>,"status";
-+ i2c0_baudrate = <&i2c0>,"clock-frequency:0";
-+ i2c1_baudrate = <&i2c1>,"clock-frequency:0";
-+ i2c2_baudrate = <&i2c2>,"clock-frequency:0";
-+ core_freq = <&clk_core>,"clock-frequency:0";
-+
-+ act_led_gpio = <&act_led>,"gpios:4";
-+ act_led_activelow = <&act_led>,"gpios:8";
-+ act_led_trigger = <&act_led>,"linux,default-trigger";
-+
-+ pwr_led_gpio = <&pwr_led>,"gpios:4";
-+ pwr_led_activelow = <&pwr_led>,"gpios:8";
-+ pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
-+
-+ audio = <&audio>,"status";
-+ watchdog = <&watchdog>,"status";
-+ random = <&random>,"status";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/bcm2708-rpi-b.dts
-@@ -0,0 +1,135 @@
-+/dts-v1/;
-+
-+#include "bcm2708.dtsi"
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+ model = "Raspberry Pi Model B";
-+};
-+
-+&gpio {
-+ sdhost_pins: sdhost_pins {
-+ brcm,pins = <48 49 50 51 52 53>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+
-+ spi0_pins: spi0_pins {
-+ brcm,pins = <9 10 11>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+
-+ spi0_cs_pins: spi0_cs_pins {
-+ brcm,pins = <8 7>;
-+ brcm,function = <1>; /* output */
-+ };
-+
-+ i2c0_pins: i2c0 {
-+ brcm,pins = <0 1>;
-+ brcm,function = <4>;
-+ };
-+
-+ i2c1_pins: i2c1 {
-+ brcm,pins = <2 3>;
-+ brcm,function = <4>;
-+ };
-+
-+ i2s_pins: i2s {
-+ brcm,pins = <28 29 30 31>;
-+ brcm,function = <6>; /* alt2 */
-+ };
-+};
-+
-+&sdhost {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&sdhost_pins>;
-+ bus-width = <4>;
-+ status = "okay";
-+};
-+
-+&fb {
-+ status = "okay";
-+};
-+
-+&uart0 {
-+ status = "okay";
-+};
-+
-+&spi0 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
-+ cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
-+
-+ spidev at 0{
-+ compatible = "spidev";
-+ reg = <0>; /* CE0 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ };
-+
-+ spidev at 1{
-+ compatible = "spidev";
-+ reg = <1>; /* CE1 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ };
-+};
-+
-+&i2c0 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2c0_pins>;
-+ clock-frequency = <100000>;
-+};
-+
-+&i2c1 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2c1_pins>;
-+ clock-frequency = <100000>;
-+};
-+
-+&i2c2 {
-+ clock-frequency = <100000>;
-+};
-+
-+&i2s {
-+ #sound-dai-cells = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2s_pins>;
-+};
-+
-+&random {
-+ status = "okay";
-+};
-+
-+&leds {
-+ act_led: act {
-+ label = "led0";
-+ linux,default-trigger = "mmc0";
-+ gpios = <&gpio 16 1>;
-+ };
-+};
-+
-+/ {
-+ __overrides__ {
-+ uart0 = <&uart0>,"status";
-+ uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
-+ i2s = <&i2s>,"status";
-+ spi = <&spi0>,"status";
-+ i2c0 = <&i2c0>,"status";
-+ i2c1 = <&i2c1>,"status";
-+ i2c2_iknowwhatimdoing = <&i2c2>,"status";
-+ i2c0_baudrate = <&i2c0>,"clock-frequency:0";
-+ i2c1_baudrate = <&i2c1>,"clock-frequency:0";
-+ i2c2_baudrate = <&i2c2>,"clock-frequency:0";
-+ core_freq = <&clk_core>,"clock-frequency:0";
-+
-+ act_led_gpio = <&act_led>,"gpios:4";
-+ act_led_activelow = <&act_led>,"gpios:8";
-+ act_led_trigger = <&act_led>,"linux,default-trigger";
-+
-+ audio = <&audio>,"status";
-+ watchdog = <&watchdog>,"status";
-+ random = <&random>,"status";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/bcm2708-rpi-cm.dts
-@@ -0,0 +1,102 @@
-+/dts-v1/;
-+
-+#include "bcm2708-rpi-cm.dtsi"
-+
-+/ {
-+ model = "Raspberry Pi Compute Module";
-+};
-+
-+&uart0 {
-+ status = "okay";
-+};
-+
-+&gpio {
-+ spi0_pins: spi0_pins {
-+ brcm,pins = <9 10 11>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+
-+ spi0_cs_pins: spi0_cs_pins {
-+ brcm,pins = <8 7>;
-+ brcm,function = <1>; /* output */
-+ };
-+
-+ i2c0_pins: i2c0 {
-+ brcm,pins = <0 1>;
-+ brcm,function = <4>;
-+ };
-+
-+ i2c1_pins: i2c1 {
-+ brcm,pins = <2 3>;
-+ brcm,function = <4>;
-+ };
-+
-+ i2s_pins: i2s {
-+ brcm,pins = <18 19 20 21>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+};
-+
-+&spi0 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
-+ cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
-+
-+ spidev at 0{
-+ compatible = "spidev";
-+ reg = <0>; /* CE0 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ };
-+
-+ spidev at 1{
-+ compatible = "spidev";
-+ reg = <1>; /* CE1 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ };
-+};
-+
-+&i2c0 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2c0_pins>;
-+ clock-frequency = <100000>;
-+};
-+
-+&i2c1 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2c1_pins>;
-+ clock-frequency = <100000>;
-+};
-+
-+&i2c2 {
-+ clock-frequency = <100000>;
-+};
-+
-+&i2s {
-+ #sound-dai-cells = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2s_pins>;
-+};
-+
-+&random {
-+ status = "okay";
-+};
-+
-+/ {
-+ __overrides__ {
-+ uart0 = <&uart0>,"status";
-+ uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
-+ i2s = <&i2s>,"status";
-+ spi = <&spi0>,"status";
-+ i2c0 = <&i2c0>,"status";
-+ i2c1 = <&i2c1>,"status";
-+ i2c2_iknowwhatimdoing = <&i2c2>,"status";
-+ i2c0_baudrate = <&i2c0>,"clock-frequency:0";
-+ i2c1_baudrate = <&i2c1>,"clock-frequency:0";
-+ i2c2_baudrate = <&i2c2>,"clock-frequency:0";
-+ core_freq = <&clk_core>,"clock-frequency:0";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/bcm2708-rpi-cm.dtsi
-@@ -0,0 +1,40 @@
-+#include "bcm2708.dtsi"
-+
-+&gpio {
-+ sdhost_pins: sdhost_pins {
-+ brcm,pins = <48 49 50 51 52 53>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+};
-+
-+&leds {
-+ act_led: act {
-+ label = "led0";
-+ linux,default-trigger = "mmc0";
-+ gpios = <&gpio 47 0>;
-+ };
-+};
-+
-+&sdhost {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&sdhost_pins>;
-+ bus-width = <4>;
-+ non-removable;
-+ status = "okay";
-+};
-+
-+&fb {
-+ status = "okay";
-+};
-+
-+/ {
-+ __overrides__ {
-+ act_led_gpio = <&act_led>,"gpios:4";
-+ act_led_activelow = <&act_led>,"gpios:8";
-+ act_led_trigger = <&act_led>,"linux,default-trigger";
-+
-+ audio = <&audio>,"status";
-+ watchdog = <&watchdog>,"status";
-+ random = <&random>,"status";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/bcm2708.dtsi
-@@ -0,0 +1,40 @@
-+#include "bcm2708_common.dtsi"
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+ model = "BCM2708";
-+
-+ chosen {
-+ /* No padding required - the boot loader can do that. */
-+ bootargs = "";
-+ };
-+
-+ soc {
-+ ranges = <0x7e000000 0x20000000 0x01000000>;
-+
-+ timer at 7e003000 {
-+ compatible = "brcm,bcm2835-system-timer";
-+ reg = <0x7e003000 0x1000>;
-+ interrupts = <1 0>, <1 1>, <1 2>, <1 3>;
-+ clock-frequency = <1000000>;
-+ };
-+
-+ arm-pmu {
-+ compatible = "arm,arm1176-pmu";
-+ };
-+
-+ gpiomem {
-+ compatible = "brcm,bcm2835-gpiomem";
-+ reg = <0x7e200000 0x1000>;
-+ status = "okay";
-+ };
-+ };
-+};
-+
-+&intc {
-+ compatible = "brcm,bcm2835-armctrl-ic";
-+};
-+
-+&watchdog {
-+ status = "okay";
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/bcm2708_common.dtsi
-@@ -0,0 +1,347 @@
-+#include "skeleton.dtsi"
-+
-+/ {
-+ interrupt-parent = <&intc>;
-+
-+ aliases {
-+ audio = &audio;
-+ sound = &sound;
-+ soc = &soc;
-+ dma = &dma;
-+ intc = &intc;
-+ watchdog = &watchdog;
-+ random = &random;
-+ mailbox = &mailbox;
-+ gpio = &gpio;
-+ uart0 = &uart0;
-+ sdhost = &sdhost;
-+ i2s = &i2s;
-+ spi0 = &spi0;
-+ i2c0 = &i2c0;
-+ uart1 = &uart1;
-+ mmc = &mmc;
-+ i2c1 = &i2c1;
-+ i2c2 = &i2c2;
-+ usb = &usb;
-+ leds = &leds;
-+ fb = &fb;
-+ vchiq = &vchiq;
-+ thermal = &thermal;
-+ clocks = &clocks;
-+ };
-+
-+ /* Onboard audio */
-+ audio: audio {
-+ compatible = "brcm,bcm2835-audio";
-+ brcm,pwm-channels = <8>;
-+ status = "disabled";
-+ };
-+
-+ /* External sound card */
-+ sound: sound {
-+ };
-+
-+ soc: soc {
-+ compatible = "simple-bus";
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+
-+ dma: dma at 7e007000 {
-+ compatible = "brcm,bcm2835-dma";
-+ reg = <0x7e007000 0xf00>;
-+ interrupts = <1 16>,
-+ <1 17>,
-+ <1 18>,
-+ <1 19>,
-+ <1 20>,
-+ <1 21>,
-+ <1 22>,
-+ <1 23>,
-+ <1 24>,
-+ <1 25>,
-+ <1 26>,
-+ <1 27>;
-+
-+ #dma-cells = <1>;
-+ brcm,dma-channel-mask = <0x0f35>;
-+ };
-+
-+ intc: interrupt-controller at 7e00b200 {
-+ compatible = "brcm,bcm2708-armctrl-ic";
-+ reg = <0x7e00b200 0x200>;
-+ interrupt-controller;
-+ #interrupt-cells = <2>;
-+ };
-+
-+ mailbox: mailbox at 7e00b800 {
-+ compatible = "brcm,bcm2835-mbox";
-+ reg = <0x7e00b880 0x40>;
-+ interrupts = <0 1>;
-+ #mbox-cells = <0>;
-+ };
-+
-+ watchdog: watchdog at 7e100000 {
-+ compatible = "brcm,bcm2835-pm-wdt";
-+ reg = <0x7e100000 0x28>;
-+ status = "disabled";
-+ };
-+
-+ cprman: cprman at 7e101000 {
-+ compatible = "brcm,bcm2835-cprman";
-+ #clock-cells = <1>;
-+ reg = <0x7e101000 0x2000>;
-+
-+ /* CPRMAN derives everything from the platform's
-+ * oscillator.
-+ */
-+ clocks = <&clk_osc>;
-+ status = "disabled";
-+ };
-+
-+ random: rng at 7e104000 {
-+ compatible = "brcm,bcm2835-rng";
-+ reg = <0x7e104000 0x10>;
-+ status = "disabled";
-+ };
-+
-+ gpio: gpio at 7e200000 {
-+ compatible = "brcm,bcm2835-gpio";
-+ reg = <0x7e200000 0xb4>;
-+ interrupts = <2 17>, <2 18>;
-+
-+ gpio-controller;
-+ #gpio-cells = <2>;
-+
-+ interrupt-controller;
-+ #interrupt-cells = <2>;
-+ };
-+
-+ uart0: uart at 7e201000 {
-+ compatible = "arm,pl011", "arm,primecell";
-+ reg = <0x7e201000 0x1000>;
-+ interrupts = <2 25>;
-+ clocks = <&clk_uart0 &clk_apb_p>;
-+ clock-names = "uartclk","apb_pclk";
-+ arm,primecell-periphid = <0x00241011>; // For an explanation, see
-+ // https://github.com/raspberrypi/linux/commit/13731d862cf5219216533a3b0de052cee4cc5038
-+ status = "disabled";
-+ };
-+
-+ sdhost: sdhost at 7e202000 {
-+ compatible = "brcm,bcm2835-sdhost";
-+ reg = <0x7e202000 0x100>;
-+ interrupts = <2 24>;
-+ clocks = <&clk_core>;
-+ dmas = <&dma 13>,
-+ <&dma 13>;
-+ dma-names = "tx", "rx";
-+ brcm,pio-limit = <1>;
-+ status = "disabled";
-+ };
-+
-+ i2s: i2s at 7e203000 {
-+ compatible = "brcm,bcm2835-i2s";
-+ reg = <0x7e203000 0x24>,
-+ <0x7e101098 0x08>;
-+
-+ dmas = <&dma 2>, <&dma 3>;
-+ dma-names = "tx", "rx";
-+ status = "disabled";
-+ };
-+
-+ spi0: spi at 7e204000 {
-+ compatible = "brcm,bcm2835-spi";
-+ reg = <0x7e204000 0x1000>;
-+ interrupts = <2 22>;
-+ clocks = <&clk_core>;
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "disabled";
-+ /* the dma channels */
-+ dmas = <&dma 6>, <&dma 7>;
-+ dma-names = "tx", "rx";
-+ /* the chipselects used - <0> means native GPIO
-+ * add more gpios if necessary as <&gpio 6 1>
-+ * (but do not forget to make them output!)
-+ */
-+ cs-gpios = <0>, <0>;
-+ };
-+
-+ i2c0: i2c at 7e205000 {
-+ compatible = "brcm,bcm2708-i2c";
-+ reg = <0x7e205000 0x1000>;
-+ interrupts = <2 21>;
-+ clocks = <&clk_core>;
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "disabled";
-+ };
-+
-+ pwm: pwm at 7e20c000 {
-+ compatible = "brcm,bcm2835-pwm";
-+ reg = <0x7e20c000 0x28>;
-+ clocks = <&clk_pwm>;
-+ #pwm-cells = <2>;
-+ status = "disabled";
-+ };
-+
-+ uart1: uart at 7e215040 {
-+ compatible = "brcm,bcm2835-aux-uart", "ns16550";
-+ reg = <0x7e215040 0x40>;
-+ interrupts = <1 29>;
-+ clocks = <&clk_uart1>;
-+ reg-shift = <2>;
-+ no-loopback-test;
-+ status = "disabled";
-+ };
-+
-+ mmc: mmc at 7e300000 {
-+ compatible = "brcm,bcm2835-mmc";
-+ reg = <0x7e300000 0x100>;
-+ interrupts = <2 30>;
-+ clocks = <&clk_mmc>;
-+ dmas = <&dma 11>,
-+ <&dma 11>;
-+ dma-names = "tx", "rx";
-+ status = "disabled";
-+ };
-+
-+ i2c1: i2c at 7e804000 {
-+ compatible = "brcm,bcm2708-i2c";
-+ reg = <0x7e804000 0x1000>;
-+ interrupts = <2 21>;
-+ clocks = <&clk_core>;
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "disabled";
-+ };
-+
-+ i2c2: i2c at 7e805000 {
-+ // Beware - this is shared with the HDMI module.
-+ // Careless use may break (really) your display.
-+ // Caveat emptor.
-+ compatible = "brcm,bcm2708-i2c";
-+ reg = <0x7e805000 0x1000>;
-+ interrupts = <2 21>;
-+ clocks = <&clk_core>;
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "disabled";
-+ };
-+
-+ smi: smi at 7e600000 {
-+ compatible = "brcm,bcm2835-smi";
-+ reg = <0x7e600000 0x44>, <0x7e1010b0 0x8>;
-+ interrupts = <2 16>;
-+ brcm,smi-clock-source = <6>;
-+ brcm,smi-clock-divisor = <4>;
-+ dmas = <&dma 4>;
-+ dma-names = "rx-tx";
-+ status = "disabled";
-+ };
-+
-+ usb: usb at 7e980000 {
-+ compatible = "brcm,bcm2708-usb";
-+ reg = <0x7e980000 0x10000>,
-+ <0x7e006000 0x1000>;
-+ interrupts = <2 0>,
-+ <1 9>;
-+ };
-+
-+ firmware: firmware {
-+ compatible = "raspberrypi,bcm2835-firmware";
-+ mboxes = <&mailbox>;
-+ };
-+
-+ leds: leds {
-+ compatible = "gpio-leds";
-+ };
-+
-+ fb: fb {
-+ compatible = "brcm,bcm2708-fb";
-+ firmware = <&firmware>;
-+ status = "disabled";
-+ };
-+
-+ vchiq: vchiq {
-+ compatible = "brcm,bcm2835-vchiq";
-+ reg = <0x7e00b840 0xf>;
-+ interrupts = <0 2>;
-+ cache-line-size = <32>;
-+ firmware = <&firmware>;
-+ };
-+
-+ thermal: thermal {
-+ compatible = "brcm,bcm2835-thermal";
-+ firmware = <&firmware>;
-+ };
-+ };
-+
-+ clocks: clocks {
-+ compatible = "simple-bus";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ clk_core: clock at 0 {
-+ compatible = "fixed-clock";
-+ reg = <0>;
-+ #clock-cells = <0>;
-+ clock-output-names = "core";
-+ clock-frequency = <250000000>;
-+ };
-+
-+ clk_mmc: clock at 1 {
-+ compatible = "fixed-clock";
-+ reg = <1>;
-+ #clock-cells = <0>;
-+ clock-output-names = "mmc";
-+ clock-frequency = <250000000>;
-+ };
-+
-+ clk_uart0: clock at 2 {
-+ compatible = "fixed-clock";
-+ reg = <2>;
-+ #clock-cells = <0>;
-+ clock-output-names = "uart0_pclk";
-+ clock-frequency = <3000000>;
-+ };
-+
-+ clk_apb_p: clock at 3 {
-+ compatible = "fixed-clock";
-+ reg = <3>;
-+ #clock-cells = <0>;
-+ clock-output-names = "apb_pclk";
-+ clock-frequency = <126000000>;
-+ };
-+
-+ clk_pwm: clock at 4 {
-+ compatible = "fixed-clock";
-+ reg = <4>;
-+ #clock-cells = <0>;
-+ clock-output-names = "pwm";
-+ clock-frequency = <100000000>;
-+ };
-+
-+ clk_uart1: clock at 5 {
-+ compatible = "fixed-factor-clock";
-+ reg = <5>;
-+ clocks = <&clk_core>;
-+ #clock-cells = <0>;
-+ clock-div = <1>;
-+ clock-mult = <2>;
-+ };
-+
-+ /* The oscillator is the root of the clock tree. */
-+ clk_osc: clock at 6 {
-+ compatible = "fixed-clock";
-+ reg = <6>;
-+ #clock-cells = <0>;
-+ clock-output-names = "osc";
-+ clock-frequency = <19200000>;
-+ };
-+ };
-+
-+ __overrides__ {
-+ cache_line_size = <&vchiq>, "cache-line-size:0";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/bcm2709-rpi-2-b.dts
-@@ -0,0 +1,145 @@
-+/dts-v1/;
-+
-+#include "bcm2709.dtsi"
-+
-+/ {
-+ compatible = "brcm,bcm2709";
-+ model = "Raspberry Pi 2 Model B";
-+};
-+
-+&gpio {
-+ sdhost_pins: sdhost_pins {
-+ brcm,pins = <48 49 50 51 52 53>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+
-+ spi0_pins: spi0_pins {
-+ brcm,pins = <9 10 11>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+
-+ spi0_cs_pins: spi0_cs_pins {
-+ brcm,pins = <8 7>;
-+ brcm,function = <1>; /* output */
-+ };
-+
-+ i2c0_pins: i2c0 {
-+ brcm,pins = <0 1>;
-+ brcm,function = <4>;
-+ };
-+
-+ i2c1_pins: i2c1 {
-+ brcm,pins = <2 3>;
-+ brcm,function = <4>;
-+ };
-+
-+ i2s_pins: i2s {
-+ brcm,pins = <18 19 20 21>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+};
-+
-+&sdhost {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&sdhost_pins>;
-+ bus-width = <4>;
-+ status = "okay";
-+};
-+
-+&fb {
-+ status = "okay";
-+};
-+
-+&uart0 {
-+ status = "okay";
-+};
-+
-+&spi0 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
-+ cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
-+
-+ spidev at 0{
-+ compatible = "spidev";
-+ reg = <0>; /* CE0 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ };
-+
-+ spidev at 1{
-+ compatible = "spidev";
-+ reg = <1>; /* CE1 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ };
-+};
-+
-+&i2c0 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2c0_pins>;
-+ clock-frequency = <100000>;
-+};
-+
-+&i2c1 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2c1_pins>;
-+ clock-frequency = <100000>;
-+};
-+
-+&i2c2 {
-+ clock-frequency = <100000>;
-+};
-+
-+&i2s {
-+ #sound-dai-cells = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2s_pins>;
-+};
-+
-+&random {
-+ status = "okay";
-+};
-+
-+&leds {
-+ act_led: act {
-+ label = "led0";
-+ linux,default-trigger = "mmc0";
-+ gpios = <&gpio 47 0>;
-+ };
-+
-+ pwr_led: pwr {
-+ label = "led1";
-+ linux,default-trigger = "input";
-+ gpios = <&gpio 35 0>;
-+ };
-+};
-+
-+/ {
-+ __overrides__ {
-+ uart0 = <&uart0>,"status";
-+ uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
-+ i2s = <&i2s>,"status";
-+ spi = <&spi0>,"status";
-+ i2c0 = <&i2c0>,"status";
-+ i2c1 = <&i2c1>,"status";
-+ i2c2_iknowwhatimdoing = <&i2c2>,"status";
-+ i2c0_baudrate = <&i2c0>,"clock-frequency:0";
-+ i2c1_baudrate = <&i2c1>,"clock-frequency:0";
-+ i2c2_baudrate = <&i2c2>,"clock-frequency:0";
-+ core_freq = <&clk_core>,"clock-frequency:0";
-+
-+ act_led_gpio = <&act_led>,"gpios:4";
-+ act_led_activelow = <&act_led>,"gpios:8";
-+ act_led_trigger = <&act_led>,"linux,default-trigger";
-+
-+ pwr_led_gpio = <&pwr_led>,"gpios:4";
-+ pwr_led_activelow = <&pwr_led>,"gpios:8";
-+ pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
-+
-+ audio = <&audio>,"status";
-+ watchdog = <&watchdog>,"status";
-+ random = <&random>,"status";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/bcm2709.dtsi
-@@ -0,0 +1,102 @@
-+#include "bcm2708_common.dtsi"
-+
-+/ {
-+ compatible = "brcm,bcm2709";
-+ model = "BCM2709";
-+
-+ chosen {
-+ /* No padding required - the boot loader can do that. */
-+ bootargs = "";
-+ };
-+
-+ soc {
-+ ranges = <0x7e000000 0x3f000000 0x01000000>,
-+ <0x40000000 0x40000000 0x00040000>;
-+
-+ local_intc: local_intc {
-+ compatible = "brcm,bcm2836-l1-intc";
-+ reg = <0x40000000 0x100>;
-+ interrupt-controller;
-+ #interrupt-cells = <1>;
-+ interrupt-parent = <&local_intc>;
-+ };
-+
-+ arm-pmu {
-+ compatible = "arm,cortex-a7-pmu";
-+ interrupt-parent = <&local_intc>;
-+ interrupts = <9>;
-+ };
-+
-+ gpiomem {
-+ compatible = "brcm,bcm2835-gpiomem";
-+ reg = <0x7e200000 0x1000>;
-+ status = "okay";
-+ };
-+
-+ timer {
-+ compatible = "arm,armv7-timer";
-+ clock-frequency = <19200000>;
-+ interrupt-parent = <&local_intc>;
-+ interrupts = <0>, // PHYS_SECURE_PPI
-+ <1>, // PHYS_NONSECURE_PPI
-+ <3>, // VIRT_PPI
-+ <2>; // HYP_PPI
-+ always-on;
-+ };
-+
-+ syscon at 40000000 {
-+ compatible = "brcm,bcm2836-arm-local", "syscon";
-+ reg = <0x40000000 0x100>;
-+ };
-+ };
-+
-+ cpus: cpus {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ v7_cpu0: cpu at 0 {
-+ device_type = "cpu";
-+ compatible = "arm,cortex-a7";
-+ reg = <0xf00>;
-+ clock-frequency = <800000000>;
-+ };
-+
-+ v7_cpu1: cpu at 1 {
-+ device_type = "cpu";
-+ compatible = "arm,cortex-a7";
-+ reg = <0xf01>;
-+ clock-frequency = <800000000>;
-+ };
-+
-+ v7_cpu2: cpu at 2 {
-+ device_type = "cpu";
-+ compatible = "arm,cortex-a7";
-+ reg = <0xf02>;
-+ clock-frequency = <800000000>;
-+ };
-+
-+ v7_cpu3: cpu at 3 {
-+ device_type = "cpu";
-+ compatible = "arm,cortex-a7";
-+ reg = <0xf03>;
-+ clock-frequency = <800000000>;
-+ };
-+ };
-+
-+ __overrides__ {
-+ arm_freq = <&v7_cpu0>, "clock-frequency:0",
-+ <&v7_cpu1>, "clock-frequency:0",
-+ <&v7_cpu2>, "clock-frequency:0",
-+ <&v7_cpu3>, "clock-frequency:0";
-+ };
-+};
-+
-+&watchdog {
-+ status = "okay";
-+};
-+
-+&intc {
-+ compatible = "brcm,bcm2836-armctrl-ic";
-+ interrupt-parent = <&local_intc>;
-+ interrupts = <8>;
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/bcm2835-rpi-cm.dts
-@@ -0,0 +1,93 @@
-+/dts-v1/;
-+
-+#include "bcm2835-rpi-cm.dtsi"
-+
-+/ {
-+ model = "Raspberry Pi Compute Module";
-+};
-+
-+&uart0 {
-+ status = "okay";
-+};
-+
-+&gpio {
-+ spi0_pins: spi0_pins {
-+ brcm,pins = <7 8 9 10 11>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+
-+ i2c0_pins: i2c0 {
-+ brcm,pins = <0 1>;
-+ brcm,function = <4>;
-+ };
-+
-+ i2c1_pins: i2c1 {
-+ brcm,pins = <2 3>;
-+ brcm,function = <4>;
-+ };
-+
-+ i2s_pins: i2s {
-+ brcm,pins = <18 19 20 21>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+};
-+
-+&spi0 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&spi0_pins>;
-+
-+ spidev at 0{
-+ compatible = "spidev";
-+ reg = <0>; /* CE0 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ };
-+
-+ spidev at 1{
-+ compatible = "spidev";
-+ reg = <1>; /* CE1 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ };
-+};
-+
-+&i2c0 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2c0_pins>;
-+ clock-frequency = <100000>;
-+};
-+
-+&i2c1 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2c1_pins>;
-+ clock-frequency = <100000>;
-+};
-+
-+&i2c2 {
-+ clock-frequency = <100000>;
-+};
-+
-+&i2s {
-+ #sound-dai-cells = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2s_pins>;
-+};
-+
-+/ {
-+ __overrides__ {
-+ uart0 = <&uart0>,"status";
-+ uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
-+ uart1_clkrate = <&uart1>,"clock-frequency:0";
-+ i2s = <&i2s>,"status";
-+ spi = <&spi0>,"status";
-+ i2c0 = <&i2c0>,"status";
-+ i2c1 = <&i2c1>,"status";
-+ i2c2_iknowwhatimdoing = <&i2c2>,"status";
-+ i2c0_baudrate = <&i2c0>,"clock-frequency:0";
-+ i2c1_baudrate = <&i2c1>,"clock-frequency:0";
-+ i2c2_baudrate = <&i2c2>,"clock-frequency:0";
-+ core_freq = <&clk_core>,"clock-frequency:0";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/bcm2835-rpi-cm.dtsi
-@@ -0,0 +1,30 @@
-+#include "bcm2835.dtsi"
-+
-+&leds {
-+ act_led: act {
-+ label = "led0";
-+ linux,default-trigger = "mmc0";
-+ gpios = <&gpio 47 0>;
-+ };
-+};
-+
-+&mmc {
-+ status = "okay";
-+ bus-width = <4>;
-+};
-+
-+&fb {
-+ status = "okay";
-+};
-+
-+/ {
-+ __overrides__ {
-+ act_led_gpio = <&act_led>,"gpios:4";
-+ act_led_activelow = <&act_led>,"gpios:8";
-+ act_led_trigger = <&act_led>,"linux,default-trigger";
-+
-+ audio = <&audio>,"status";
-+ watchdog = <&watchdog>,"status";
-+ random = <&random>,"status";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -0,0 +1,69 @@
-+ifeq ($(CONFIG_OF),y)
-+
-+# Overlays for the Raspberry Pi platform
-+
-+ifeq ($(CONFIG_ARCH_BCM2708),y)
-+ RPI_DT_OVERLAYS=y
-+endif
-+ifeq ($(CONFIG_ARCH_BCM2709),y)
-+ RPI_DT_OVERLAYS=y
-+endif
-+ifeq ($(CONFIG_ARCH_BCM2835),y)
-+ RPI_DT_OVERLAYS=y
-+endif
-+
-+dtb-$(RPI_DT_OVERLAYS) += ads7846-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += bmp085_i2c-sensor-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += dht11-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += enc28j60-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += gpio-poweroff-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += hifiberry-amp-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += hifiberry-dac-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += hifiberry-dacplus-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += hifiberry-digi-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += hy28a-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += hy28b-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += i2c-rtc-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += i2s-mmap-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += iqaudio-dac-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += iqaudio-dacplus-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += lirc-rpi-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += mcp2515-can0-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += mcp2515-can1-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += mmc-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += mz61581-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += piscreen-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += pitft28-resistive-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += pps-gpio-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += pwm-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += pwm-2chan-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += raspidac3-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += rpi-dac-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += rpi-display-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += rpi-ft5406-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += rpi-proto-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += rpi-sense-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += sdhost-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += sdio-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += smi-dev-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += smi-nand-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += smi-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += spi-gpio35-39-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += tinylcd35-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += uart1-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += vga666-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += w1-gpio-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += w1-gpio-pullup-overlay.dtb
-+
-+targets += dtbs dtbs_install
-+targets += $(dtb-y)
-+
-+endif
-+
-+always := $(dtb-y)
-+clean-files := *.dtb
-+
-+# Enable fixups to support overlays on BCM2708 platforms
-+ifeq ($(RPI_DT_OVERLAYS),y)
-+ DTC_FLAGS ?= -@
-+endif
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -0,0 +1,648 @@
-+Introduction
-+============
-+
-+This directory contains Device Tree overlays. Device Tree makes it possible
-+to support many hardware configurations with a single kernel and without the
-+need to explicitly load or blacklist kernel modules. Note that this isn't a
-+"pure" Device Tree configuration (c.f. MACH_BCM2835) - some on-board devices
-+are still configured by the board support code, but the intention is to
-+eventually reach that goal.
-+
-+On Raspberry Pi, Device Tree usage is controlled from /boot/config.txt. By
-+default, the Raspberry Pi kernel boots with device tree enabled. You can
-+completely disable DT usage (for now) by adding:
-+
-+ device_tree=
-+
-+to your config.txt, which should cause your Pi to revert to the old way of
-+doing things after a reboot.
-+
-+In /boot you will find a .dtb for each base platform. This describes the
-+hardware that is part of the Raspberry Pi board. The loader (start.elf and its
-+siblings) selects the .dtb file appropriate for the platform by name, and reads
-+it into memory. At this point, all of the optional interfaces (i2c, i2s, spi)
-+are disabled, but they can be enabled using Device Tree parameters:
-+
-+ dtparam=i2c=on,i2s=on,spi=on
-+
-+However, this shouldn't be necessary in many use cases because loading an
-+overlay that requires one of those interfaces will cause it to be enabled
-+automatically, and it is advisable to only enable interfaces if they are
-+needed.
-+
-+Configuring additional, optional hardware is done using Device Tree overlays
-+(see below).
-+
-+raspi-config
-+============
-+
-+The Advanced Options section of the raspi-config utility can enable and disable
-+Device Tree use, as well as toggling the I2C and SPI interfaces. Note that it
-+is possible to both enable an interface and blacklist the driver, if for some
-+reason you should want to defer the loading.
-+
-+Modules
-+=======
-+
-+As well as describing the hardware, Device Tree also gives enough information
-+to allow suitable driver modules to be located and loaded, with the corollary
-+that unneeded modules are not loaded. As a result it should be possible to
-+remove lines from /etc/modules, and /etc/modprobe.d/raspi-blacklist.conf can
-+have its contents deleted (or commented out).
-+
-+Using Overlays
-+==============
-+
-+Overlays are loaded using the "dtoverlay" directive. As an example, consider the
-+popular lirc-rpi module, the Linux Infrared Remote Control driver. In the
-+pre-DT world this would be loaded from /etc/modules, with an explicit
-+"modprobe lirc-rpi" command, or programmatically by lircd. With DT enabled,
-+this becomes a line in config.txt:
-+
-+ dtoverlay=lirc-rpi
-+
-+This causes the file /boot/overlays/lirc-rpi-overlay.dtb to be loaded. By
-+default it will use GPIOs 17 (out) and 18 (in), but this can be modified using
-+DT parameters:
-+
-+ dtoverlay=lirc-rpi,gpio_out_pin=17,gpio_in_pin=13
-+
-+Parameters always have default values, although in some cases (e.g. "w1-gpio")
-+it is necessary to provided multiple overlays in order to get the desired
-+behaviour. See the list of overlays below for a description of the parameters and their defaults.
-+
-+The Overlay and Parameter Reference
-+===================================
-+
-+N.B. When editing this file, please preserve the indentation levels to make it simple to parse
-+programmatically. NO HARD TABS.
-+
-+
-+Name: <The base DTB>
-+Info: Configures the base Raspberry Pi hardware
-+Load: <loaded automatically>
-+Params:
-+ audio Set to "on" to enable the onboard ALSA audio
-+ interface (default "off")
-+
-+ i2c_arm Set to "on" to enable the ARM's i2c interface
-+ (default "off")
-+
-+ i2c_vc Set to "on" to enable the i2c interface
-+ usually reserved for the VideoCore processor
-+ (default "off")
-+
-+ i2c An alias for i2c_arm
-+
-+ i2c_arm_baudrate Set the baudrate of the ARM's i2c interface
-+ (default "100000")
-+
-+ i2c_vc_baudrate Set the baudrate of the VideoCore i2c interface
-+ (default "100000")
-+
-+ i2c_baudrate An alias for i2c_arm_baudrate
-+
-+ i2s Set to "on" to enable the i2s interface
-+ (default "off")
-+
-+ spi Set to "on" to enable the spi interfaces
-+ (default "off")
-+
-+ random Set to "on" to enable the hardware random
-+ number generator (default "on")
-+
-+ uart0 Set to "off" to disable uart0 (default "on")
-+
-+ watchdog Set to "on" to enable the hardware watchdog
-+ (default "off")
-+
-+ act_led_trigger Choose which activity the LED tracks.
-+ Use "heartbeat" for a nice load indicator.
-+ (default "mmc")
-+
-+ act_led_activelow Set to "on" to invert the sense of the LED
-+ (default "off")
-+
-+ act_led_gpio Set which GPIO to use for the activity LED
-+ (in case you want to connect it to an external
-+ device)
-+ (default "16" on a non-Plus board, "47" on a
-+ Plus or Pi 2)
-+
-+ pwr_led_trigger
-+ pwr_led_activelow
-+ pwr_led_gpio
-+ As for act_led_*, but using the PWR LED.
-+ Not available on Model A/B boards.
-+
-+ N.B. It is recommended to only enable those interfaces that are needed.
-+ Leaving all interfaces enabled can lead to unwanted behaviour (i2c_vc
-+ interfering with Pi Camera, I2S and SPI hogging GPIO pins, etc.)
-+ Note also that i2c, i2c_arm and i2c_vc are aliases for the physical
-+ interfaces i2c0 and i2c1. Use of the numeric variants is still possible
-+ but deprecated because the ARM/VC assignments differ between board
-+ revisions. The same board-specific mapping applies to i2c_baudrate,
-+ and the other i2c baudrate parameters.
-+
-+
-+Name: ads7846
-+Info: ADS7846 Touch controller
-+Load: dtoverlay=ads7846,<param>=<val>
-+Params: cs SPI bus Chip Select (default 1)
-+ speed SPI bus speed (default 2Mhz, max 3.25MHz)
-+ penirq GPIO used for PENIRQ. REQUIRED
-+ penirq_pull Set GPIO pull (default 0=none, 2=pullup)
-+ swapxy Swap x and y axis
-+ xmin Minimum value on the X axis (default 0)
-+ ymin Minimum value on the Y axis (default 0)
-+ xmax Maximum value on the X axis (default 4095)
-+ ymax Maximum value on the Y axis (default 4095)
-+ pmin Minimum reported pressure value (default 0)
-+ pmax Maximum reported pressure value (default 65535)
-+ xohms Touchpanel sensitivity (X-plate resistance)
-+ (default 400)
-+
-+ penirq is required and usually xohms (60-100) has to be set as well.
-+ Apart from that, pmax (255) and swapxy are also common.
-+ The rest of the calibration can be done with xinput-calibrator.
-+ See: github.com/notro/fbtft/wiki/FBTFT-on-Raspian
-+ Device Tree binding document:
-+ www.kernel.org/doc/Documentation/devicetree/bindings/input/ads7846.txt
-+
-+
-+Name: bmp085_i2c-sensor
-+Info: Configures the BMP085/BMP180 digital barometric pressure and temperature
-+ sensors from Bosch Sensortec
-+Load: dtoverlay=bmp085_i2c-sensor
-+Params: <None>
-+
-+
-+Name: dht11
-+Info: Overlay for the DHT11/DHT21/DHT22 humidity/temperature sensors
-+ Also sometimes found with the part number(s) AM230x.
-+Load: dtoverlay=dht11,<param>=<val>
-+Params: gpiopin GPIO connected to the sensor's DATA output.
-+ (default 4)
-+
-+
-+[ The ds1307-rtc overlay has been deleted. See i2c-rtc. ]
-+
-+
-+Name: enc28j60
-+Info: Overlay for the Microchip ENC28J60 Ethernet Controller (SPI)
-+Load: dtoverlay=enc28j60,<param>=<val>
-+Params: int_pin GPIO used for INT (default 25)
-+
-+ speed SPI bus speed (default 12000000)
-+
-+
-+Name: gpio-poweroff
-+Info: Drives a GPIO high or low on reboot
-+Load: dtoverlay=gpio-poweroff,<param>=<val>
-+Params: gpiopin GPIO for signalling (default 26)
-+
-+ active_low Set if the power control device requires a
-+ high->low transition to trigger a power-down.
-+ Note that this will require the support of a
-+ custom dt-blob.bin to prevent a power-down
-+ during the boot process, and that a reboot
-+ will also cause the pin to go low.
-+
-+
-+Name: hifiberry-amp
-+Info: Configures the HifiBerry Amp and Amp+ audio cards
-+Load: dtoverlay=hifiberry-amp
-+Params: <None>
-+
-+
-+Name: hifiberry-dac
-+Info: Configures the HifiBerry DAC audio card
-+Load: dtoverlay=hifiberry-dac
-+Params: <None>
-+
-+
-+Name: hifiberry-dacplus
-+Info: Configures the HifiBerry DAC+ audio card
-+Load: dtoverlay=hifiberry-dacplus
-+Params: <None>
-+
-+
-+Name: hifiberry-digi
-+Info: Configures the HifiBerry Digi audio card
-+Load: dtoverlay=hifiberry-digi
-+Params: <None>
-+
-+
-+Name: hy28a
-+Info: HY28A - 2.8" TFT LCD Display Module by HAOYU Electronics
-+ Default values match Texy's display shield
-+Load: dtoverlay=hy28a,<param>=<val>
-+Params: speed Display SPI bus speed
-+
-+ rotate Display rotation {0,90,180,270}
-+
-+ fps Delay between frame updates
-+
-+ debug Debug output level {0-7}
-+
-+ xohms Touchpanel sensitivity (X-plate resistance)
-+
-+ resetgpio GPIO used to reset controller
-+
-+ ledgpio GPIO used to control backlight
-+
-+
-+Name: hy28b
-+Info: HY28B - 2.8" TFT LCD Display Module by HAOYU Electronics
-+ Default values match Texy's display shield
-+Load: dtoverlay=hy28b,<param>=<val>
-+Params: speed Display SPI bus speed
-+
-+ rotate Display rotation {0,90,180,270}
-+
-+ fps Delay between frame updates
-+
-+ debug Debug output level {0-7}
-+
-+ xohms Touchpanel sensitivity (X-plate resistance)
-+
-+ resetgpio GPIO used to reset controller
-+
-+ ledgpio GPIO used to control backlight
-+
-+
-+Name: i2c-rtc
-+Info: Adds support for a number of I2C Real Time Clock devices
-+Load: dtoverlay=i2c-rtc,<param>
-+Params: ds1307 Select the DS1307 device
-+
-+ ds3231 Select the DS3231 device
-+
-+ mcp7941x Select the MCP7941x device
-+
-+ pcf2127 Select the PCF2127 device
-+
-+ pcf8523 Select the PCF8523 device
-+
-+ pcf8563 Select the PCF8563 device
-+
-+
-+Name: i2s-mmap
-+Info: Enables mmap support in the bcm2708-i2s driver
-+Load: dtoverlay=i2s-mmap
-+Params: <None>
-+
-+
-+Name: iqaudio-dac
-+Info: Configures the IQaudio DAC audio card
-+Load: dtoverlay=iqaudio-dac
-+Params: <None>
-+
-+
-+Name: iqaudio-dacplus
-+Info: Configures the IQaudio DAC+ audio card
-+Load: dtoverlay=iqaudio-dacplus
-+Params: <None>
-+
-+
-+Name: lirc-rpi
-+Info: Configures lirc-rpi (Linux Infrared Remote Control for Raspberry Pi)
-+ Consult the module documentation for more details.
-+Load: dtoverlay=lirc-rpi,<param>=<val>,...
-+Params: gpio_out_pin GPIO for output (default "17")
-+
-+ gpio_in_pin GPIO for input (default "18")
-+
-+ gpio_in_pull Pull up/down/off on the input pin
-+ (default "down")
-+
-+ sense Override the IR receive auto-detection logic:
-+ "0" = force active-high
-+ "1" = force active-low
-+ "-1" = use auto-detection
-+ (default "-1")
-+
-+ softcarrier Turn the software carrier "on" or "off"
-+ (default "on")
-+
-+ invert "on" = invert the output pin (default "off")
-+
-+ debug "on" = enable additional debug messages
-+ (default "off")
-+
-+
-+Name: mcp2515-can0
-+Info: Configures the MCP2515 CAN controller on spi0.0
-+Load: dtoverlay=mcp2515-can0,<param>=<val>
-+Params: oscillator Clock frequency for the CAN controller (Hz)
-+
-+ spimaxfrequency Maximum SPI frequence (Hz)
-+
-+ interrupt GPIO for interrupt signal
-+
-+
-+Name: mcp2515-can1
-+Info: Configures the MCP2515 CAN controller on spi0.1
-+Load: dtoverlay=mcp2515-can1,<param>=<val>
-+Params: oscillator Clock frequency for the CAN controller (Hz)
-+
-+ spimaxfrequency Maximum SPI frequence (Hz)
-+
-+ interrupt GPIO for interrupt signal
-+
-+
-+Name: mmc
-+Info: Selects the bcm2835-mmc SD/MMC driver, optionally with overclock
-+Load: dtoverlay=mmc,<param>=<val>
-+Params: overclock_50 Clock (in MHz) to use when the MMC framework
-+ requests 50MHz
-+ force_pio Disable DMA support
-+
-+
-+Name: mz61581
-+Info: MZ61581 display by Tontec
-+Load: dtoverlay=mz61581,<param>=<val>
-+Params: speed Display SPI bus speed
-+
-+ rotate Display rotation {0,90,180,270}
-+
-+ fps Delay between frame updates
-+
-+ txbuflen Transmit buffer length (default 32768)
-+
-+ debug Debug output level {0-7}
-+
-+ xohms Touchpanel sensitivity (X-plate resistance)
-+
-+
-+[ The pcf2127-rtc overlay has been deleted. See i2c-rtc. ]
-+
-+
-+[ The pcf8523-rtc overlay has been deleted. See i2c-rtc. ]
-+
-+
-+[ The pcf8563-rtc overlay has been deleted. See i2c-rtc. ]
-+
-+
-+Name: piscreen
-+Info: PiScreen display by OzzMaker.com
-+Load: dtoverlay=piscreen,<param>=<val>
-+Params: speed Display SPI bus speed
-+
-+ rotate Display rotation {0,90,180,270}
-+
-+ fps Delay between frame updates
-+
-+ debug Debug output level {0-7}
-+
-+ xohms Touchpanel sensitivity (X-plate resistance)
-+
-+
-+Name: pitft28-resistive
-+Info: Adafruit PiTFT 2.8" resistive touch screen
-+Load: dtoverlay=pitft28-resistive,<param>=<val>
-+Params: speed Display SPI bus speed
-+
-+ rotate Display rotation {0,90,180,270}
-+
-+ fps Delay between frame updates
-+
-+ debug Debug output level {0-7}
-+
-+
-+Name: pps-gpio
-+Info: Configures the pps-gpio (pulse-per-second time signal via GPIO).
-+Load: dtoverlay=pps-gpio,<param>=<val>
-+Params: gpiopin Input GPIO (default "18")
-+
-+
-+Name: pwm
-+Info: Configures a single PWM channel
-+ Legal pin,function combinations for each channel:
-+ PWM0: 12,4(Alt0) 18,2(Alt5) 40,4(Alt0) 52,5(Alt1)
-+ PWM1: 13,4(Alt0) 19,2(Alt5) 41,4(Alt0) 45,4(Alt0) 53,5(Alt1)
-+ N.B.:
-+ 1) Pin 18 is the only one available on all platforms, and
-+ it is the one used by the I2S audio interface.
-+ Pins 12 and 13 might be better choices on an A+, B+ or Pi2.
-+ 2) The onboard analogue audio output uses both PWM channels.
-+ 3) So be careful mixing audio and PWM.
-+ 4) Currently the clock must have been enabled and configured
-+ by other means.
-+Load: dtoverlay=pwm,<param>=<val>
-+Params: pin Output pin (default 18) - see table
-+ func Pin function (default 2 = Alt5) - see above
-+ clock PWM clock frequency (informational)
-+
-+
-+Name: pwm-2chan
-+Info: Configures both PWM channels
-+ Legal pin,function combinations for each channel:
-+ PWM0: 12,4(Alt0) 18,2(Alt5) 40,4(Alt0) 52,5(Alt1)
-+ PWM1: 13,4(Alt0) 19,2(Alt5) 41,4(Alt0) 45,4(Alt0) 53,5(Alt1)
-+ N.B.:
-+ 1) Pin 18 is the only one available on all platforms, and
-+ it is the one used by the I2S audio interface.
-+ Pins 12 and 13 might be better choices on an A+, B+ or Pi2.
-+ 2) The onboard analogue audio output uses both PWM channels.
-+ 3) So be careful mixing audio and PWM.
-+ 4) Currently the clock must have been enabled and configured
-+ by other means.
-+Load: dtoverlay=pwm-2chan,<param>=<val>
-+Params: pin Output pin (default 18) - see table
-+ pin2 Output pin for other channel (default 19)
-+ func Pin function (default 2 = Alt5) - see above
-+ func2 Function for pin2 (default 2 = Alt5)
-+ clock PWM clock frequency (informational)
-+
-+
-+Name: raspidac3
-+Info: Configures the RaspiDAV Rev.3x audio card
-+Load: dtoverlay=raspidac3
-+Params: <None>
-+
-+
-+Name: rpi-dac
-+Info: Configures the RPi DAC audio card
-+Load: dtoverlay=rpi-dac
-+Params: <None>
-+
-+
-+Name: rpi-display
-+Info: RPi-Display - 2.8" Touch Display by Watterott
-+Load: dtoverlay=rpi-display,<param>=<val>
-+Params: speed Display SPI bus speed
-+
-+ rotate Display rotation {0,90,180,270}
-+
-+ fps Delay between frame updates
-+
-+ debug Debug output level {0-7}
-+
-+ xohms Touchpanel sensitivity (X-plate resistance)
-+
-+
-+Name: rpi-ft5406
-+Info: Official Raspberry Pi display touchscreen
-+Load: dtoverlay=rpi-ft5406
-+Params: <None>
-+
-+
-+Name: rpi-proto
-+Info: Configures the RPi Proto audio card
-+Load: dtoverlay=rpi-proto
-+Params: <None>
-+
-+
-+Name: rpi-sense
-+Info: Raspberry Pi Sense HAT
-+Load: dtoverlay=rpi-sense
-+Params: <None>
-+
-+
-+Name: sdhost
-+Info: Selects the bcm2835-sdhost SD/MMC driver, optionally with overclock
-+Load: dtoverlay=sdhost,<param>=<val>
-+Params: overclock_50 Clock (in MHz) to use when the MMC framework
-+ requests 50MHz
-+
-+ force_pio Disable DMA support (default off)
-+
-+ pio_limit Number of blocks above which to use DMA
-+ (default 1)
-+
-+ debug Enable debug output (default off)
-+
-+
-+Name: sdio
-+Info: Selects the bcm2835-sdhost SD/MMC driver, optionally with overclock,
-+ and enables SDIO via GPIOs 22-27.
-+Load: dtoverlay=sdio,<param>=<val>
-+Params: overclock_50 Clock (in MHz) to use when the MMC framework
-+ requests 50MHz
-+
-+ force_pio Disable DMA support (default off)
-+
-+ pio_limit Number of blocks above which to use DMA
-+ (default 1)
-+
-+ debug Enable debug output (default off)
-+
-+ poll_once Disable SDIO-device polling every second
-+ (default on: polling once at boot-time)
-+
-+
-+Name: smi
-+Info: Enables the Secondary Memory Interface peripheral. Uses GPIOs 2-25!
-+Load: dtoverlay=smi
-+Params: <None>
-+
-+
-+Name: smi-dev
-+Info: Enables the userspace interface for the SMI driver
-+Load: dtoverlay=smi-dev
-+Params: <None>
-+
-+
-+Name: smi-nand
-+Info: Enables access to NAND flash via the SMI interface
-+Load: dtoverlay=smi-nand
-+Params: <None>
-+
-+
-+Name: spi-gpio35-39
-+Info: move SPI function block to GPIO 35 to 39
-+Load: dtoverlay=spi-gpio35-39
-+Params: <None>
-+
-+
-+Name: tinylcd35
-+Info: 3.5" Color TFT Display by www.tinylcd.com
-+ Options: Touch, RTC, keypad
-+Load: dtoverlay=tinylcd35,<param>=<val>
-+Params: speed Display SPI bus speed
-+
-+ rotate Display rotation {0,90,180,270}
-+
-+ fps Delay between frame updates
-+
-+ debug Debug output level {0-7}
-+
-+ touch Enable touch panel
-+
-+ touchgpio Touch controller IRQ GPIO
-+
-+ xohms Touchpanel: Resistance of X-plate in ohms
-+
-+ rtc-pcf PCF8563 Real Time Clock
-+
-+ rtc-ds DS1307 Real Time Clock
-+
-+ keypad Enable keypad
-+
-+ Examples:
-+ Display with touchpanel, PCF8563 RTC and keypad:
-+ dtoverlay=tinylcd35,touch,rtc-pcf,keypad
-+ Old touch display:
-+ dtoverlay=tinylcd35,touch,touchgpio=3
-+
-+
-+Name: uart1
-+Info: Enable uart1 in place of uart0
-+Load: dtoverlay=uart1,<param>=<val>
-+Params: txd1_pin GPIO pin for TXD1 (14, 32 or 40 - default 14)
-+
-+ rxd1_pin GPIO pin for RXD1 (15, 33 or 41 - default 15)
-+
-+
-+Name: vga666
-+Info: Overlay for the Fen Logic VGA666 board
-+ This uses GPIOs 2-21 (so no I2C), and activates the output 2-3 seconds
-+ after the kernel has started.
-+Load: dtoverlay=vga666
-+Params: <None>
-+
-+
-+Name: w1-gpio
-+Info: Configures the w1-gpio Onewire interface module.
-+ Use this overlay if you *don't* need a GPIO to drive an external pullup.
-+Load: dtoverlay=w1-gpio,<param>=<val>
-+Params: gpiopin GPIO for I/O (default "4")
-+
-+ pullup Non-zero, "on", or "y" to enable the parasitic
-+ power (2-wire, power-on-data) feature
-+
-+
-+Name: w1-gpio-pullup
-+Info: Configures the w1-gpio Onewire interface module.
-+ Use this overlay if you *do* need a GPIO to drive an external pullup.
-+Load: dtoverlay=w1-gpio-pullup,<param>=<val>
-+Params: gpiopin GPIO for I/O (default "4")
-+
-+ pullup Non-zero, "on", or "y" to enable the parasitic
-+ power (2-wire, power-on-data) feature
-+
-+ extpullup GPIO for external pullup (default "5")
-+
-+
-+Troubleshooting
-+===============
-+
-+If you are experiencing problems that you think are DT-related, enable DT
-+diagnostic output by adding this to /boot/config.txt:
-+
-+ dtdebug=on
-+
-+and rebooting. Then run:
-+
-+ sudo vcdbg log msg
-+
-+and look for relevant messages.
-+
-+Further reading
-+===============
-+
-+This is only meant to be a quick introduction to the subject of Device Tree on
-+Raspberry Pi. There is a more complete explanation here:
-+
-+http://www.raspberrypi.org/documentation/configuration/device-tree.md
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/ads7846-overlay.dts
-@@ -0,0 +1,83 @@
-+/*
-+ * Generic Device Tree overlay for the ADS7846 touch controller
-+ *
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ status = "okay";
-+
-+ spidev at 0{
-+ status = "disabled";
-+ };
-+
-+ spidev at 1{
-+ status = "disabled";
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ ads7846_pins: ads7846_pins {
-+ brcm,pins = <255>; /* illegal default value */
-+ brcm,function = <0>; /* in */
-+ brcm,pull = <0>; /* none */
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ /* needed to avoid dtc warning */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ ads7846: ads7846 at 1 {
-+ compatible = "ti,ads7846";
-+ reg = <1>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&ads7846_pins>;
-+
-+ spi-max-frequency = <2000000>;
-+ interrupts = <255 2>; /* high-to-low edge triggered */
-+ interrupt-parent = <&gpio>;
-+ pendown-gpio = <&gpio 255 0>;
-+
-+ /* driver defaults */
-+ ti,x-min = /bits/ 16 <0>;
-+ ti,y-min = /bits/ 16 <0>;
-+ ti,x-max = /bits/ 16 <0x0FFF>;
-+ ti,y-max = /bits/ 16 <0x0FFF>;
-+ ti,pressure-min = /bits/ 16 <0>;
-+ ti,pressure-max = /bits/ 16 <0xFFFF>;
-+ ti,x-plate-ohms = /bits/ 16 <400>;
-+ };
-+ };
-+ };
-+ __overrides__ {
-+ cs = <&ads7846>,"reg:0";
-+ speed = <&ads7846>,"spi-max-frequency:0";
-+ penirq = <&ads7846_pins>,"brcm,pins:0", /* REQUIRED */
-+ <&ads7846>,"interrupts:0",
-+ <&ads7846>,"pendown-gpio:4";
-+ penirq_pull = <&ads7846_pins>,"brcm,pull:0";
-+ swapxy = <&ads7846>,"ti,swap-xy?";
-+ xmin = <&ads7846>,"ti,x-min;0";
-+ ymin = <&ads7846>,"ti,y-min;0";
-+ xmax = <&ads7846>,"ti,x-max;0";
-+ ymax = <&ads7846>,"ti,y-max;0";
-+ pmin = <&ads7846>,"ti,pressure-min;0";
-+ pmax = <&ads7846>,"ti,pressure-max;0";
-+ xohms = <&ads7846>,"ti,x-plate-ohms;0";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/bmp085_i2c-sensor-overlay.dts
-@@ -0,0 +1,23 @@
-+// Definitions for BMP085/BMP180 digital barometric pressure and temperature sensors from Bosch Sensortec
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&i2c_arm>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ bmp085 at 77 {
-+ compatible = "bosch,bmp085";
-+ reg = <0x77>;
-+ default-oversampling = <3>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/dht11-overlay.dts
-@@ -0,0 +1,39 @@
-+/*
-+ * Overlay for the DHT11/21/22 humidity/temperature sensor modules.
-+ */
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target-path = "/";
-+ __overlay__ {
-+
-+ dht11: dht11 at 0 {
-+ compatible = "dht11";
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&dht11_pins>;
-+ gpios = <&gpio 4 0>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ dht11_pins: dht11_pins {
-+ brcm,pins = <4>;
-+ brcm,function = <0>; // in
-+ brcm,pull = <0>; // off
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ gpiopin = <&dht11_pins>,"brcm,pins:0",
-+ <&dht11>,"gpios:4";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/enc28j60-overlay.dts
-@@ -0,0 +1,50 @@
-+// Overlay for the Microchip ENC28J60 Ethernet Controller
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ /* needed to avoid dtc warning */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ status = "okay";
-+
-+ spidev at 0{
-+ status = "disabled";
-+ };
-+
-+ eth1: enc28j60 at 0{
-+ compatible = "microchip,enc28j60";
-+ reg = <0>; /* CE0 */
-+ pinctrl-names = "default";
-+ pinctrl-0 = <ð1_pins>;
-+ interrupt-parent = <&gpio>;
-+ interrupts = <25 0x2>; /* falling edge */
-+ spi-max-frequency = <12000000>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ eth1_pins: eth1_pins {
-+ brcm,pins = <25>;
-+ brcm,function = <0>; /* in */
-+ brcm,pull = <0>; /* none */
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ int_pin = <ð1>, "interrupts:0",
-+ <ð1_pins>, "brcm,pins:0";
-+ speed = <ð1>, "spi-max-frequency:0";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/gpio-poweroff-overlay.dts
-@@ -0,0 +1,34 @@
-+// Definitions for gpio-poweroff module
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target-path = "/";
-+ __overlay__ {
-+ power_ctrl: power_ctrl {
-+ compatible = "gpio-poweroff";
-+ gpios = <&gpio 26 0>;
-+ force;
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ power_ctrl_pins: power_ctrl_pins {
-+ brcm,pins = <26>;
-+ brcm,function = <1>; // out
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ gpiopin = <&power_ctrl>,"gpios:4",
-+ <&power_ctrl_pins>,"brcm,pins:0";
-+ active_low = <&power_ctrl>,"gpios:8";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/hifiberry-amp-overlay.dts
-@@ -0,0 +1,39 @@
-+// Definitions for HiFiBerry Amp/Amp+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&sound>;
-+ __overlay__ {
-+ compatible = "hifiberry,hifiberry-amp";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&i2s>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&i2c1>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ tas5713 at 1b {
-+ #sound-dai-cells = <0>;
-+ compatible = "ti,tas5713";
-+ reg = <0x1b>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/hifiberry-dac-overlay.dts
-@@ -0,0 +1,34 @@
-+// Definitions for HiFiBerry DAC
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&sound>;
-+ __overlay__ {
-+ compatible = "hifiberry,hifiberry-dac";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&i2s>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target-path = "/";
-+ __overlay__ {
-+ pcm5102a-codec {
-+ #sound-dai-cells = <0>;
-+ compatible = "ti,pcm5102a";
-+ status = "okay";
-+ };
-+ };
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/hifiberry-dacplus-overlay.dts
-@@ -0,0 +1,39 @@
-+// Definitions for HiFiBerry DAC+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&sound>;
-+ __overlay__ {
-+ compatible = "hifiberry,hifiberry-dacplus";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&i2s>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&i2c1>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ pcm5122 at 4d {
-+ #sound-dai-cells = <0>;
-+ compatible = "ti,pcm5122";
-+ reg = <0x4d>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/hifiberry-digi-overlay.dts
-@@ -0,0 +1,39 @@
-+// Definitions for HiFiBerry Digi
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&sound>;
-+ __overlay__ {
-+ compatible = "hifiberry,hifiberry-digi";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&i2s>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&i2c1>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ wm8804 at 3b {
-+ #sound-dai-cells = <0>;
-+ compatible = "wlf,wm8804";
-+ reg = <0x3b>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/hy28a-overlay.dts
-@@ -0,0 +1,87 @@
-+/*
-+ * Device Tree overlay for HY28A display
-+ *
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ status = "okay";
-+
-+ spidev at 0{
-+ status = "disabled";
-+ };
-+
-+ spidev at 1{
-+ status = "disabled";
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ hy28a_pins: hy28a_pins {
-+ brcm,pins = <17 25 18>;
-+ brcm,function = <0 1 1>; /* in out out */
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ /* needed to avoid dtc warning */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ hy28a: hy28a at 0{
-+ compatible = "ilitek,ili9320";
-+ reg = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&hy28a_pins>;
-+
-+ spi-max-frequency = <32000000>;
-+ spi-cpol;
-+ spi-cpha;
-+ rotate = <270>;
-+ bgr;
-+ fps = <50>;
-+ buswidth = <8>;
-+ startbyte = <0x70>;
-+ reset-gpios = <&gpio 25 0>;
-+ led-gpios = <&gpio 18 1>;
-+ debug = <0>;
-+ };
-+
-+ hy28a_ts: hy28a-ts at 1 {
-+ compatible = "ti,ads7846";
-+ reg = <1>;
-+
-+ spi-max-frequency = <2000000>;
-+ interrupts = <17 2>; /* high-to-low edge triggered */
-+ interrupt-parent = <&gpio>;
-+ pendown-gpio = <&gpio 17 0>;
-+ ti,x-plate-ohms = /bits/ 16 <100>;
-+ ti,pressure-max = /bits/ 16 <255>;
-+ };
-+ };
-+ };
-+ __overrides__ {
-+ speed = <&hy28a>,"spi-max-frequency:0";
-+ rotate = <&hy28a>,"rotate:0";
-+ fps = <&hy28a>,"fps:0";
-+ debug = <&hy28a>,"debug:0";
-+ xohms = <&hy28a_ts>,"ti,x-plate-ohms;0";
-+ resetgpio = <&hy28a>,"reset-gpios:4",
-+ <&hy28a_pins>, "brcm,pins:1";
-+ ledgpio = <&hy28a>,"led-gpios:4",
-+ <&hy28a_pins>, "brcm,pins:2";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/hy28b-overlay.dts
-@@ -0,0 +1,142 @@
-+/*
-+ * Device Tree overlay for HY28b display shield by Texy
-+ *
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ status = "okay";
-+
-+ spidev at 0{
-+ status = "disabled";
-+ };
-+
-+ spidev at 1{
-+ status = "disabled";
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ hy28b_pins: hy28b_pins {
-+ brcm,pins = <17 25 18>;
-+ brcm,function = <0 1 1>; /* in out out */
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ /* needed to avoid dtc warning */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ hy28b: hy28b at 0{
-+ compatible = "ilitek,ili9325";
-+ reg = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&hy28b_pins>;
-+
-+ spi-max-frequency = <48000000>;
-+ spi-cpol;
-+ spi-cpha;
-+ rotate = <270>;
-+ bgr;
-+ fps = <50>;
-+ buswidth = <8>;
-+ startbyte = <0x70>;
-+ reset-gpios = <&gpio 25 0>;
-+ led-gpios = <&gpio 18 1>;
-+
-+ gamma = "04 1F 4 7 7 0 7 7 6 0\n0F 00 1 7 4 0 0 0 6 7";
-+
-+ init = <0x10000e7 0x0010
-+ 0x1000000 0x0001
-+ 0x1000001 0x0100
-+ 0x1000002 0x0700
-+ 0x1000003 0x1030
-+ 0x1000004 0x0000
-+ 0x1000008 0x0207
-+ 0x1000009 0x0000
-+ 0x100000a 0x0000
-+ 0x100000c 0x0001
-+ 0x100000d 0x0000
-+ 0x100000f 0x0000
-+ 0x1000010 0x0000
-+ 0x1000011 0x0007
-+ 0x1000012 0x0000
-+ 0x1000013 0x0000
-+ 0x2000032
-+ 0x1000010 0x1590
-+ 0x1000011 0x0227
-+ 0x2000032
-+ 0x1000012 0x009c
-+ 0x2000032
-+ 0x1000013 0x1900
-+ 0x1000029 0x0023
-+ 0x100002b 0x000e
-+ 0x2000032
-+ 0x1000020 0x0000
-+ 0x1000021 0x0000
-+ 0x2000032
-+ 0x1000050 0x0000
-+ 0x1000051 0x00ef
-+ 0x1000052 0x0000
-+ 0x1000053 0x013f
-+ 0x1000060 0xa700
-+ 0x1000061 0x0001
-+ 0x100006a 0x0000
-+ 0x1000080 0x0000
-+ 0x1000081 0x0000
-+ 0x1000082 0x0000
-+ 0x1000083 0x0000
-+ 0x1000084 0x0000
-+ 0x1000085 0x0000
-+ 0x1000090 0x0010
-+ 0x1000092 0x0000
-+ 0x1000093 0x0003
-+ 0x1000095 0x0110
-+ 0x1000097 0x0000
-+ 0x1000098 0x0000
-+ 0x1000007 0x0133
-+ 0x1000020 0x0000
-+ 0x1000021 0x0000
-+ 0x2000064>;
-+ debug = <0>;
-+ };
-+
-+ hy28b_ts: hy28b-ts at 1 {
-+ compatible = "ti,ads7846";
-+ reg = <1>;
-+
-+ spi-max-frequency = <2000000>;
-+ interrupts = <17 2>; /* high-to-low edge triggered */
-+ interrupt-parent = <&gpio>;
-+ pendown-gpio = <&gpio 17 0>;
-+ ti,x-plate-ohms = /bits/ 16 <100>;
-+ ti,pressure-max = /bits/ 16 <255>;
-+ };
-+ };
-+ };
-+ __overrides__ {
-+ speed = <&hy28b>,"spi-max-frequency:0";
-+ rotate = <&hy28b>,"rotate:0";
-+ fps = <&hy28b>,"fps:0";
-+ debug = <&hy28b>,"debug:0";
-+ xohms = <&hy28b_ts>,"ti,x-plate-ohms;0";
-+ resetgpio = <&hy28b>,"reset-gpios:4",
-+ <&hy28b_pins>, "brcm,pins:1";
-+ ledgpio = <&hy28b>,"led-gpios:4",
-+ <&hy28b_pins>, "brcm,pins:2";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts
-@@ -0,0 +1,55 @@
-+// Definitions for several I2C based Real Time Clocks
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&i2c_arm>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ ds1307: ds1307 at 68 {
-+ compatible = "maxim,ds1307";
-+ reg = <0x68>;
-+ status = "disable";
-+ };
-+ mcp7941x: mcp7941x at 6f {
-+ compatible = "microchip,mcp7941x";
-+ reg = <0x6f>;
-+ status = "disable";
-+ };
-+ ds3231: ds3231 at 68 {
-+ compatible = "maxim,ds3231";
-+ reg = <0x68>;
-+ status = "disable";
-+ };
-+ pcf2127: pcf2127 at 51 {
-+ compatible = "nxp,pcf2127";
-+ reg = <0x51>;
-+ status = "disable";
-+ };
-+ pcf8523: pcf8523 at 68 {
-+ compatible = "nxp,pcf8523";
-+ reg = <0x68>;
-+ status = "disable";
-+ };
-+ pcf8563: pcf8563 at 51 {
-+ compatible = "nxp,pcf8563";
-+ reg = <0x51>;
-+ status = "disable";
-+ };
-+ };
-+ };
-+ __overrides__ {
-+ ds1307 = <&ds1307>,"status";
-+ ds3231 = <&ds3231>,"status";
-+ mcp7941x = <&mcp7941x>,"status";
-+ pcf2127 = <&pcf2127>,"status";
-+ pcf8523 = <&pcf8523>,"status";
-+ pcf8563 = <&pcf8563>,"status";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/i2s-mmap-overlay.dts
-@@ -0,0 +1,13 @@
-+/dts-v1/;
-+/plugin/;
-+
-+/{
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&i2s>;
-+ __overlay__ {
-+ brcm,enable-mmap;
-+ };
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/iqaudio-dac-overlay.dts
-@@ -0,0 +1,39 @@
-+// Definitions for IQaudIO DAC
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&sound>;
-+ __overlay__ {
-+ compatible = "iqaudio,iqaudio-dac";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&i2s>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&i2c1>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ pcm5122 at 4c {
-+ #sound-dai-cells = <0>;
-+ compatible = "ti,pcm5122";
-+ reg = <0x4c>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/iqaudio-dacplus-overlay.dts
-@@ -0,0 +1,39 @@
-+// Definitions for IQaudIO DAC+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&sound>;
-+ __overlay__ {
-+ compatible = "iqaudio,iqaudio-dac";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&i2s>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&i2c1>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ pcm5122 at 4c {
-+ #sound-dai-cells = <0>;
-+ compatible = "ti,pcm5122";
-+ reg = <0x4c>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/lirc-rpi-overlay.dts
-@@ -0,0 +1,57 @@
-+// Definitions for lirc-rpi module
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target-path = "/";
-+ __overlay__ {
-+ lirc_rpi: lirc_rpi {
-+ compatible = "rpi,lirc-rpi";
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&lirc_pins>;
-+ status = "okay";
-+
-+ // Override autodetection of IR receiver circuit
-+ // (0 = active high, 1 = active low, -1 = no override )
-+ rpi,sense = <0xffffffff>;
-+
-+ // Software carrier
-+ // (0 = off, 1 = on)
-+ rpi,softcarrier = <1>;
-+
-+ // Invert output
-+ // (0 = off, 1 = on)
-+ rpi,invert = <0>;
-+
-+ // Enable debugging messages
-+ // (0 = off, 1 = on)
-+ rpi,debug = <0>;
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ lirc_pins: lirc_pins {
-+ brcm,pins = <17 18>;
-+ brcm,function = <1 0>; // out in
-+ brcm,pull = <0 1>; // off down
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ gpio_out_pin = <&lirc_pins>,"brcm,pins:0";
-+ gpio_in_pin = <&lirc_pins>,"brcm,pins:4";
-+ gpio_in_pull = <&lirc_pins>,"brcm,pull:4";
-+
-+ sense = <&lirc_rpi>,"rpi,sense:0";
-+ softcarrier = <&lirc_rpi>,"rpi,softcarrier:0";
-+ invert = <&lirc_rpi>,"rpi,invert:0";
-+ debug = <&lirc_rpi>,"rpi,debug:0";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/mcp2515-can0-overlay.dts
-@@ -0,0 +1,69 @@
-+/*
-+ * Device tree overlay for mcp251x/can0 on spi0.0
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2836", "brcm,bcm2708", "brcm,bcm2709";
-+ /* disable spi-dev for spi0.0 */
-+ fragment at 0 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ status = "okay";
-+ spidev at 0{
-+ status = "disabled";
-+ };
-+ };
-+ };
-+
-+ /* the interrupt pin of the can-controller */
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ can0_pins: can0_pins {
-+ brcm,pins = <25>;
-+ brcm,function = <0>; /* input */
-+ };
-+ };
-+ };
-+
-+ /* the clock/oscillator of the can-controller */
-+ fragment at 2 {
-+ target-path = "/clocks";
-+ __overlay__ {
-+ /* external oscillator of mcp2515 on SPI0.0 */
-+ can0_osc: can0_osc {
-+ compatible = "fixed-clock";
-+ #clock-cells = <0>;
-+ clock-frequency = <16000000>;
-+ };
-+ };
-+ };
-+
-+ /* the spi config of the can-controller itself binding everything together */
-+ fragment at 3 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ /* needed to avoid dtc warning */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ can0: mcp2515 at 0 {
-+ reg = <0>;
-+ compatible = "microchip,mcp2515";
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&can0_pins>;
-+ spi-max-frequency = <10000000>;
-+ interrupt-parent = <&gpio>;
-+ interrupts = <25 0x2>;
-+ clocks = <&can0_osc>;
-+ };
-+ };
-+ };
-+ __overrides__ {
-+ oscillator = <&can0_osc>,"clock-frequency:0";
-+ spimaxfrequency = <&can0>,"spi-max-frequency:0";
-+ interrupt = <&can0_pins>,"brcm,pins:0",<&can0>,"interrupts:0";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/mcp2515-can1-overlay.dts
-@@ -0,0 +1,69 @@
-+/*
-+ * Device tree overlay for mcp251x/can1 on spi0.1 edited by petit_miner
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2836", "brcm,bcm2708", "brcm,bcm2709";
-+ /* disable spi-dev for spi0.1 */
-+ fragment at 0 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ status = "okay";
-+ spidev at 1{
-+ status = "disabled";
-+ };
-+ };
-+ };
-+
-+ /* the interrupt pin of the can-controller */
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ can1_pins: can1_pins {
-+ brcm,pins = <25>;
-+ brcm,function = <0>; /* input */
-+ };
-+ };
-+ };
-+
-+ /* the clock/oscillator of the can-controller */
-+ fragment at 2 {
-+ target-path = "/clocks";
-+ __overlay__ {
-+ /* external oscillator of mcp2515 on spi0.1 */
-+ can1_osc: can1_osc {
-+ compatible = "fixed-clock";
-+ #clock-cells = <0>;
-+ clock-frequency = <16000000>;
-+ };
-+ };
-+ };
-+
-+ /* the spi config of the can-controller itself binding everything together */
-+ fragment at 3 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ /* needed to avoid dtc warning */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ can1: mcp2515 at 1 {
-+ reg = <1>;
-+ compatible = "microchip,mcp2515";
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&can1_pins>;
-+ spi-max-frequency = <10000000>;
-+ interrupt-parent = <&gpio>;
-+ interrupts = <25 0x2>;
-+ clocks = <&can1_osc>;
-+ };
-+ };
-+ };
-+ __overrides__ {
-+ oscillator = <&can1_osc>,"clock-frequency:0";
-+ spimaxfrequency = <&can1>,"spi-max-frequency:0";
-+ interrupt = <&can1_pins>,"brcm,pins:0",<&can1>,"interrupts:0";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/mmc-overlay.dts
-@@ -0,0 +1,39 @@
-+/dts-v1/;
-+/plugin/;
-+
-+/{
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&mmc>;
-+ frag0: __overlay__ {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&mmc_pins>;
-+ bus-width = <4>;
-+ brcm,overclock-50 = <0>;
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ mmc_pins: mmc_pins {
-+ brcm,pins = <48 49 50 51 52 53>;
-+ brcm,function = <7>; /* alt3 */
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&sdhost>;
-+ __overlay__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ __overrides__ {
-+ overclock_50 = <&frag0>,"brcm,overclock-50:0";
-+ force_pio = <&frag0>,"brcm,force-pio?";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/mz61581-overlay.dts
-@@ -0,0 +1,111 @@
-+/*
-+ * Device Tree overlay for MZ61581-PI-EXT 2014.12.28 by Tontec
-+ *
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ status = "okay";
-+
-+ spidev at 0{
-+ status = "disabled";
-+ };
-+
-+ spidev at 1{
-+ status = "disabled";
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ mz61581_pins: mz61581_pins {
-+ brcm,pins = <4 15 18 25>;
-+ brcm,function = <0 1 1 1>; /* in out out out */
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ /* needed to avoid dtc warning */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ mz61581: mz61581 at 0{
-+ compatible = "samsung,s6d02a1";
-+ reg = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&mz61581_pins>;
-+
-+ spi-max-frequency = <128000000>;
-+ spi-cpol;
-+ spi-cpha;
-+
-+ width = <320>;
-+ height = <480>;
-+ rotate = <270>;
-+ bgr;
-+ fps = <30>;
-+ buswidth = <8>;
-+ txbuflen = <32768>;
-+
-+ reset-gpios = <&gpio 15 0>;
-+ dc-gpios = <&gpio 25 0>;
-+ led-gpios = <&gpio 18 0>;
-+
-+ init = <0x10000b0 00
-+ 0x1000011
-+ 0x20000ff
-+ 0x10000b3 0x02 0x00 0x00 0x00
-+ 0x10000c0 0x13 0x3b 0x00 0x02 0x00 0x01 0x00 0x43
-+ 0x10000c1 0x08 0x16 0x08 0x08
-+ 0x10000c4 0x11 0x07 0x03 0x03
-+ 0x10000c6 0x00
-+ 0x10000c8 0x03 0x03 0x13 0x5c 0x03 0x07 0x14 0x08 0x00 0x21 0x08 0x14 0x07 0x53 0x0c 0x13 0x03 0x03 0x21 0x00
-+ 0x1000035 0x00
-+ 0x1000036 0xa0
-+ 0x100003a 0x55
-+ 0x1000044 0x00 0x01
-+ 0x10000d0 0x07 0x07 0x1d 0x03
-+ 0x10000d1 0x03 0x30 0x10
-+ 0x10000d2 0x03 0x14 0x04
-+ 0x1000029
-+ 0x100002c>;
-+
-+ /* This is a workaround to make sure the init sequence slows down and doesn't fail */
-+ debug = <3>;
-+ };
-+
-+ mz61581_ts: mz61581_ts at 1 {
-+ compatible = "ti,ads7846";
-+ reg = <1>;
-+
-+ spi-max-frequency = <2000000>;
-+ interrupts = <4 2>; /* high-to-low edge triggered */
-+ interrupt-parent = <&gpio>;
-+ pendown-gpio = <&gpio 4 0>;
-+
-+ ti,x-plate-ohms = /bits/ 16 <60>;
-+ ti,pressure-max = /bits/ 16 <255>;
-+ };
-+ };
-+ };
-+ __overrides__ {
-+ speed = <&mz61581>, "spi-max-frequency:0";
-+ rotate = <&mz61581>, "rotate:0";
-+ fps = <&mz61581>, "fps:0";
-+ txbuflen = <&mz61581>, "txbuflen:0";
-+ debug = <&mz61581>, "debug:0";
-+ xohms = <&mz61581_ts>,"ti,x-plate-ohms;0";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/piscreen-overlay.dts
-@@ -0,0 +1,96 @@
-+/*
-+ * Device Tree overlay for PiScreen 3.5" display shield by Ozzmaker
-+ *
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ status = "okay";
-+
-+ spidev at 0{
-+ status = "disabled";
-+ };
-+
-+ spidev at 1{
-+ status = "disabled";
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ piscreen_pins: piscreen_pins {
-+ brcm,pins = <17 25 24 22>;
-+ brcm,function = <0 1 1 1>; /* in out out out */
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ /* needed to avoid dtc warning */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ piscreen: piscreen at 0{
-+ compatible = "ilitek,ili9486";
-+ reg = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&piscreen_pins>;
-+
-+ spi-max-frequency = <24000000>;
-+ rotate = <270>;
-+ bgr;
-+ fps = <30>;
-+ buswidth = <8>;
-+ regwidth = <16>;
-+ reset-gpios = <&gpio 25 0>;
-+ dc-gpios = <&gpio 24 0>;
-+ led-gpios = <&gpio 22 1>;
-+ debug = <0>;
-+
-+ init = <0x10000b0 0x00
-+ 0x1000011
-+ 0x20000ff
-+ 0x100003a 0x55
-+ 0x1000036 0x28
-+ 0x10000c2 0x44
-+ 0x10000c5 0x00 0x00 0x00 0x00
-+ 0x10000e0 0x0f 0x1f 0x1c 0x0c 0x0f 0x08 0x48 0x98 0x37 0x0a 0x13 0x04 0x11 0x0d 0x00
-+ 0x10000e1 0x0f 0x32 0x2e 0x0b 0x0d 0x05 0x47 0x75 0x37 0x06 0x10 0x03 0x24 0x20 0x00
-+ 0x10000e2 0x0f 0x32 0x2e 0x0b 0x0d 0x05 0x47 0x75 0x37 0x06 0x10 0x03 0x24 0x20 0x00
-+ 0x1000011
-+ 0x1000029>;
-+ };
-+
-+ piscreen_ts: piscreen-ts at 1 {
-+ compatible = "ti,ads7846";
-+ reg = <1>;
-+
-+ spi-max-frequency = <2000000>;
-+ interrupts = <17 2>; /* high-to-low edge triggered */
-+ interrupt-parent = <&gpio>;
-+ pendown-gpio = <&gpio 17 0>;
-+ ti,swap-xy;
-+ ti,x-plate-ohms = /bits/ 16 <100>;
-+ ti,pressure-max = /bits/ 16 <255>;
-+ };
-+ };
-+ };
-+ __overrides__ {
-+ speed = <&piscreen>,"spi-max-frequency:0";
-+ rotate = <&piscreen>,"rotate:0";
-+ fps = <&piscreen>,"fps:0";
-+ debug = <&piscreen>,"debug:0";
-+ xohms = <&piscreen_ts>,"ti,x-plate-ohms;0";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/pitft28-resistive-overlay.dts
-@@ -0,0 +1,115 @@
-+/*
-+ * Device Tree overlay for Adafruit PiTFT 2.8" resistive touch screen
-+ *
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ status = "okay";
-+
-+ spidev at 0{
-+ status = "disabled";
-+ };
-+
-+ spidev at 1{
-+ status = "disabled";
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ pitft_pins: pitft_pins {
-+ brcm,pins = <24 25>;
-+ brcm,function = <0 1>; /* in out */
-+ brcm,pull = <2 0>; /* pullup none */
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ /* needed to avoid dtc warning */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ pitft: pitft at 0{
-+ compatible = "ilitek,ili9340";
-+ reg = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pitft_pins>;
-+
-+ spi-max-frequency = <32000000>;
-+ rotate = <90>;
-+ fps = <25>;
-+ bgr;
-+ buswidth = <8>;
-+ dc-gpios = <&gpio 25 0>;
-+ debug = <0>;
-+ };
-+
-+ pitft_ts at 1 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ compatible = "st,stmpe610";
-+ reg = <1>;
-+
-+ spi-max-frequency = <500000>;
-+ irq-gpio = <&gpio 24 0x2>; /* IRQF_TRIGGER_FALLING */
-+ interrupts = <24 2>; /* high-to-low edge triggered */
-+ interrupt-parent = <&gpio>;
-+ interrupt-controller;
-+
-+ stmpe_touchscreen {
-+ compatible = "st,stmpe-ts";
-+ st,sample-time = <4>;
-+ st,mod-12b = <1>;
-+ st,ref-sel = <0>;
-+ st,adc-freq = <2>;
-+ st,ave-ctrl = <3>;
-+ st,touch-det-delay = <4>;
-+ st,settling = <2>;
-+ st,fraction-z = <7>;
-+ st,i-drive = <0>;
-+ };
-+
-+ stmpe_gpio: stmpe_gpio {
-+ #gpio-cells = <2>;
-+ compatible = "st,stmpe-gpio";
-+ /*
-+ * only GPIO2 is wired/available
-+ * and it is wired to the backlight
-+ */
-+ st,norequest-mask = <0x7b>;
-+ };
-+ };
-+ };
-+ };
-+
-+ fragment at 3 {
-+ target-path = "/soc";
-+ __overlay__ {
-+ backlight {
-+ compatible = "gpio-backlight";
-+ gpios = <&stmpe_gpio 2 0>;
-+ default-on;
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ speed = <&pitft>,"spi-max-frequency:0";
-+ rotate = <&pitft>,"rotate:0";
-+ fps = <&pitft>,"fps:0";
-+ debug = <&pitft>,"debug:0";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/pps-gpio-overlay.dts
-@@ -0,0 +1,34 @@
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+ fragment at 0 {
-+ target-path = "/";
-+ __overlay__ {
-+ pps: pps {
-+ compatible = "pps-gpio";
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pps_pins>;
-+ gpios = <&gpio 18 0>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ pps_pins: pps_pins {
-+ brcm,pins = <18>;
-+ brcm,function = <0>; // in
-+ brcm,pull = <0>; // off
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ gpiopin = <&pps>,"gpios:4",
-+ <&pps_pins>,"brcm,pins:0";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/pwm-2chan-overlay.dts
-@@ -0,0 +1,46 @@
-+/dts-v1/;
-+/plugin/;
-+
-+/*
-+This is the 2-channel overlay - only use it if you need both channels.
-+
-+Legal pin,function combinations for each channel:
-+ PWM0: 12,4(Alt0) 18,2(Alt5) 40,4(Alt0) 52,5(Alt1)
-+ PWM1: 13,4(Alt0) 19,2(Alt5) 41,4(Alt0) 45,4(Alt0) 53,5(Alt1)
-+
-+N.B.:
-+ 1) Pin 18 is the only one available on all platforms, and
-+ it is the one used by the I2S audio interface.
-+ Pins 12 and 13 might be better choices on an A+, B+ or Pi2.
-+ 2) The onboard analogue audio output uses both PWM channels.
-+ 3) So be careful mixing audio and PWM.
-+*/
-+
-+/ {
-+ fragment at 0 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ pwm_pins: pwm_pins {
-+ brcm,pins = <18 19>;
-+ brcm,function = <2 2>; /* Alt5 */
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&pwm>;
-+ __overlay__ {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pwm_pins>;
-+ status = "okay";
-+ };
-+ };
-+
-+ __overrides__ {
-+ pin = <&pwm_pins>,"brcm,pins:0";
-+ pin2 = <&pwm_pins>,"brcm,pins:4";
-+ func = <&pwm_pins>,"brcm,function:0";
-+ func2 = <&pwm_pins>,"brcm,function:4";
-+ clock = <&clk_pwm>,"clock-frequency:0";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/pwm-overlay.dts
-@@ -0,0 +1,42 @@
-+/dts-v1/;
-+/plugin/;
-+
-+/*
-+Legal pin,function combinations for each channel:
-+ PWM0: 12,4(Alt0) 18,2(Alt5) 40,4(Alt0) 52,5(Alt1)
-+ PWM1: 13,4(Alt0) 19,2(Alt5) 41,4(Alt0) 45,4(Alt0) 53,5(Alt1)
-+
-+N.B.:
-+ 1) Pin 18 is the only one available on all platforms, and
-+ it is the one used by the I2S audio interface.
-+ Pins 12 and 13 might be better choices on an A+, B+ or Pi2.
-+ 2) The onboard analogue audio output uses both PWM channels.
-+ 3) So be careful mixing audio and PWM.
-+*/
-+
-+/ {
-+ fragment at 0 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ pwm_pins: pwm_pins {
-+ brcm,pins = <18>;
-+ brcm,function = <2>; /* Alt5 */
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&pwm>;
-+ __overlay__ {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pwm_pins>;
-+ status = "okay";
-+ };
-+ };
-+
-+ __overrides__ {
-+ pin = <&pwm_pins>,"brcm,pins:0";
-+ func = <&pwm_pins>,"brcm,function:0";
-+ clock = <&clk_pwm>,"clock-frequency:0";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/raspidac3-overlay.dts
-@@ -0,0 +1,45 @@
-+// Definitions for RaspiDACv3
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&sound>;
-+ __overlay__ {
-+ compatible = "jg,raspidacv3";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&i2s>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&i2c1>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ pcm5122 at 4c {
-+ #sound-dai-cells = <0>;
-+ compatible = "ti,pcm5122";
-+ reg = <0x4c>;
-+ status = "okay";
-+ };
-+
-+ tpa6130a2: tpa6130a2 at 60 {
-+ compatible = "ti,tpa6130a2";
-+ reg = <0x60>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/rpi-dac-overlay.dts
-@@ -0,0 +1,34 @@
-+// Definitions for RPi DAC
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&sound>;
-+ __overlay__ {
-+ compatible = "rpi,rpi-dac";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&i2s>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target-path = "/";
-+ __overlay__ {
-+ pcm1794a-codec {
-+ #sound-dai-cells = <0>;
-+ compatible = "ti,pcm1794a";
-+ status = "okay";
-+ };
-+ };
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/rpi-display-overlay.dts
-@@ -0,0 +1,82 @@
-+/*
-+ * Device Tree overlay for rpi-display by Watterott
-+ *
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ status = "okay";
-+
-+ spidev at 0{
-+ status = "disabled";
-+ };
-+
-+ spidev at 1{
-+ status = "disabled";
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ rpi_display_pins: rpi_display_pins {
-+ brcm,pins = <18 23 24 25>;
-+ brcm,function = <1 1 1 0>; /* out out out in */
-+ brcm,pull = <0 0 0 2>; /* - - - up */
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ /* needed to avoid dtc warning */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ rpidisplay: rpi-display at 0{
-+ compatible = "ilitek,ili9341";
-+ reg = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&rpi_display_pins>;
-+
-+ spi-max-frequency = <32000000>;
-+ rotate = <270>;
-+ bgr;
-+ fps = <30>;
-+ buswidth = <8>;
-+ reset-gpios = <&gpio 23 0>;
-+ dc-gpios = <&gpio 24 0>;
-+ led-gpios = <&gpio 18 1>;
-+ debug = <0>;
-+ };
-+
-+ rpidisplay_ts: rpi-display-ts at 1 {
-+ compatible = "ti,ads7846";
-+ reg = <1>;
-+
-+ spi-max-frequency = <2000000>;
-+ interrupts = <25 2>; /* high-to-low edge triggered */
-+ interrupt-parent = <&gpio>;
-+ pendown-gpio = <&gpio 25 0>;
-+ ti,x-plate-ohms = /bits/ 16 <60>;
-+ ti,pressure-max = /bits/ 16 <255>;
-+ };
-+ };
-+ };
-+ __overrides__ {
-+ speed = <&rpidisplay>,"spi-max-frequency:0";
-+ rotate = <&rpidisplay>,"rotate:0";
-+ fps = <&rpidisplay>,"fps:0";
-+ debug = <&rpidisplay>,"debug:0";
-+ xohms = <&rpidisplay_ts>,"ti,x-plate-ohms;0";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/rpi-ft5406-overlay.dts
-@@ -0,0 +1,17 @@
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target-path = "/";
-+ __overlay__ {
-+ rpi_ft5406: rpi_ft5406 {
-+ compatible = "rpi,rpi-ft5406";
-+ firmware = <&firmware>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/rpi-proto-overlay.dts
-@@ -0,0 +1,39 @@
-+// Definitions for Rpi-Proto
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&sound>;
-+ __overlay__ {
-+ compatible = "rpi,rpi-proto";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&i2s>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&i2c1>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ wm8731 at 1a {
-+ #sound-dai-cells = <0>;
-+ compatible = "wlf,wm8731";
-+ reg = <0x1a>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/rpi-sense-overlay.dts
-@@ -0,0 +1,47 @@
-+// rpi-sense HAT
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&i2c1>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ rpi-sense at 46 {
-+ compatible = "rpi,rpi-sense";
-+ reg = <0x46>;
-+ keys-int-gpios = <&gpio 23 1>;
-+ status = "okay";
-+ };
-+
-+ lsm9ds1-magn at 1c {
-+ compatible = "st,lsm9ds1-magn";
-+ reg = <0x1c>;
-+ status = "okay";
-+ };
-+
-+ lsm9ds1-accel6a {
-+ compatible = "st,lsm9ds1-accel";
-+ reg = <0x6a>;
-+ status = "okay";
-+ };
-+
-+ lps25h-press at 5c {
-+ compatible = "st,lps25h-press";
-+ reg = <0x5c>;
-+ status = "okay";
-+ };
-+
-+ hts221-humid at 5f {
-+ compatible = "st,hts221-humid";
-+ reg = <0x5f>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/sdhost-overlay.dts
-@@ -0,0 +1,29 @@
-+/dts-v1/;
-+/plugin/;
-+
-+/{
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&mmc>;
-+ __overlay__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&sdhost>;
-+ frag1: __overlay__ {
-+ brcm,overclock-50 = <0>;
-+ brcm,pio-limit = <1>;
-+ status = "okay";
-+ };
-+ };
-+
-+ __overrides__ {
-+ overclock_50 = <&frag1>,"brcm,overclock-50:0";
-+ force_pio = <&frag1>,"brcm,force-pio?";
-+ pio_limit = <&frag1>,"brcm,pio-limit:0";
-+ debug = <&frag1>,"brcm,debug?";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/sdio-overlay.dts
-@@ -0,0 +1,32 @@
-+/* Enable SDIO from MMC interface via GPIOs 22-27. Includes sdhost overlay. */
-+
-+/include/ "sdhost-overlay.dts"
-+
-+/{
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 3 {
-+ target = <&mmc>;
-+ sdio_mmc: __overlay__ {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&sdio_pins>;
-+ non-removable;
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 4 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ sdio_pins: sdio_pins {
-+ brcm,pins = <22 23 24 25 26 27>;
-+ brcm,function = <7 7 7 7 7 7>; /* ALT3 = SD1 */
-+ brcm,pull = <0 2 2 2 2 2>;
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ poll_once = <&sdio_mmc>,"non-removable?";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/smi-dev-overlay.dts
-@@ -0,0 +1,18 @@
-+// Description: Overlay to enable character device interface for SMI.
-+// Author: Luke Wren <luke at raspberrypi.org>
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/{
-+ fragment at 0 {
-+ target = <&soc>;
-+ __overlay__ {
-+ smi_dev {
-+ compatible = "brcm,bcm2835-smi-dev";
-+ smi_handle = <&smi>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/smi-nand-overlay.dts
-@@ -0,0 +1,69 @@
-+// Description: Overlay to enable NAND flash through
-+// the secondary memory interface
-+// Author: Luke Wren
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/{
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&smi>;
-+ __overlay__ {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&smi_pins>;
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&soc>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+
-+ nand: flash at 0 {
-+ compatible = "brcm,bcm2835-smi-nand";
-+ smi_handle = <&smi>;
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+ status = "okay";
-+
-+ partition at 0 {
-+ label = "stage2";
-+ // 128k
-+ reg = <0 0x20000>;
-+ read-only;
-+ };
-+ partition at 1 {
-+ label = "firmware";
-+ // 16M
-+ reg = <0x20000 0x1000000>;
-+ read-only;
-+ };
-+ partition at 2 {
-+ label = "root";
-+ // 2G (will need to use 64 bit for >=4G)
-+ reg = <0x1020000 0x80000000>;
-+ };
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ smi_pins: smi_pins {
-+ brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11
-+ 12 13 14 15>;
-+ /* Alt 1: SMI */
-+ brcm,function = <5 5 5 5 5 5 5 5 5 5 5
-+ 5 5 5 5 5>;
-+ /* /CS, /WE and /OE are pulled high, as they are
-+ generally active low signals */
-+ brcm,pull = <2 2 2 2 2 2 2 2 0 0 0 0 0 0 0 0>;
-+ };
-+ };
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/smi-overlay.dts
-@@ -0,0 +1,37 @@
-+// Description: Overlay to enable the secondary memory interface peripheral
-+// Author: Luke Wren
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/{
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&smi>;
-+ __overlay__ {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&smi_pins>;
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ smi_pins: smi_pins {
-+ /* Don't configure the top two address bits, as
-+ these are already used as ID_SD and ID_SC */
-+ brcm,pins = <2 3 4 5 6 7 8 9 10 11 12 13 14 15
-+ 16 17 18 19 20 21 22 23 24 25>;
-+ /* Alt 0: SMI */
-+ brcm,function = <5 5 5 5 5 5 5 5 5 5 5 5 5 5 5
-+ 5 5 5 5 5 5 5 5 5>;
-+ /* /CS, /WE and /OE are pulled high, as they are
-+ generally active low signals */
-+ brcm,pull = <2 2 2 2 2 2 0 0 0 0 0 0 0 0 0 0 0
-+ 0 0 0 0 0 0 0>;
-+ };
-+ };
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/spi-gpio35-39-overlay.dts
-@@ -0,0 +1,31 @@
-+/*
-+ * Device tree overlay to move spi0 to gpio 35 to 39 on CM
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2836", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ cs-gpios = <&gpio 36 1>, <&gpio 35 1>;
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&spi0_cs_pins>;
-+ __overlay__ {
-+ bcrm,pins = <36 35>;
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&spi0_pins>;
-+ __overlay__ {
-+ bcrm,pins = <37 38 39>;
-+ };
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/tinylcd35-overlay.dts
-@@ -0,0 +1,216 @@
-+/*
-+ * tinylcd35-overlay.dts
-+ *
-+ * -------------------------------------------------
-+ * www.tinlylcd.com
-+ * -------------------------------------------------
-+ * Device---Driver-----BUS GPIO's
-+ * display tinylcd35 spi0.0 25 24 18
-+ * touch ads7846 spi0.1 5
-+ * rtc ds1307 i2c1-0068
-+ * rtc pcf8563 i2c1-0051
-+ * keypad gpio-keys --------- 17 22 27 23 28
-+ *
-+ *
-+ * TinyLCD.com 3.5 inch TFT
-+ *
-+ * Version 001
-+ * 5/3/2015 -- Noralf Trønnes Initial Device tree framework
-+ * 10/3/2015 -- tinylcd at gmail.com added ds1307 support.
-+ *
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ status = "okay";
-+
-+ spidev at 0{
-+ status = "disabled";
-+ };
-+
-+ spidev at 1{
-+ status = "disabled";
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ tinylcd35_pins: tinylcd35_pins {
-+ brcm,pins = <25 24 18>;
-+ brcm,function = <1>; /* out */
-+ };
-+ tinylcd35_ts_pins: tinylcd35_ts_pins {
-+ brcm,pins = <5>;
-+ brcm,function = <0>; /* in */
-+ };
-+ keypad_pins: keypad_pins {
-+ brcm,pins = <4 17 22 23 27>;
-+ brcm,function = <0>; /* in */
-+ brcm,pull = <1>; /* down */
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ /* needed to avoid dtc warning */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ tinylcd35: tinylcd35 at 0{
-+ compatible = "neosec,tinylcd";
-+ reg = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&tinylcd35_pins>,
-+ <&tinylcd35_ts_pins>;
-+
-+ spi-max-frequency = <48000000>;
-+ rotate = <270>;
-+ fps = <20>;
-+ bgr;
-+ buswidth = <8>;
-+ reset-gpios = <&gpio 25 0>;
-+ dc-gpios = <&gpio 24 0>;
-+ led-gpios = <&gpio 18 1>;
-+ debug = <0>;
-+
-+ init = <0x10000B0 0x80
-+ 0x10000C0 0x0A 0x0A
-+ 0x10000C1 0x01 0x01
-+ 0x10000C2 0x33
-+ 0x10000C5 0x00 0x42 0x80
-+ 0x10000B1 0xD0 0x11
-+ 0x10000B4 0x02
-+ 0x10000B6 0x00 0x22 0x3B
-+ 0x10000B7 0x07
-+ 0x1000036 0x58
-+ 0x10000F0 0x36 0xA5 0xD3
-+ 0x10000E5 0x80
-+ 0x10000E5 0x01
-+ 0x10000B3 0x00
-+ 0x10000E5 0x00
-+ 0x10000F0 0x36 0xA5 0x53
-+ 0x10000E0 0x00 0x35 0x33 0x00 0x00 0x00 0x00 0x35 0x33 0x00 0x00 0x00
-+ 0x100003A 0x55
-+ 0x1000011
-+ 0x2000001
-+ 0x1000029>;
-+ };
-+
-+ tinylcd35_ts: tinylcd35_ts at 1 {
-+ compatible = "ti,ads7846";
-+ reg = <1>;
-+ status = "disabled";
-+
-+ spi-max-frequency = <2000000>;
-+ interrupts = <5 2>; /* high-to-low edge triggered */
-+ interrupt-parent = <&gpio>;
-+ pendown-gpio = <&gpio 5 0>;
-+ ti,x-plate-ohms = /bits/ 16 <100>;
-+ ti,pressure-max = /bits/ 16 <255>;
-+ };
-+ };
-+ };
-+
-+ /* RTC */
-+
-+ fragment at 3 {
-+ target = <&i2c1>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ pcf8563: pcf8563 at 51 {
-+ compatible = "nxp,pcf8563";
-+ reg = <0x51>;
-+ status = "disabled";
-+ };
-+ };
-+ };
-+
-+ fragment at 4 {
-+ target = <&i2c1>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ ds1307: ds1307 at 68 {
-+ compatible = "maxim,ds1307";
-+ reg = <0x68>;
-+ status = "disabled";
-+ };
-+ };
-+ };
-+
-+ /*
-+ * Values for input event code is found under the
-+ * 'Keys and buttons' heading in include/uapi/linux/input.h
-+ */
-+ fragment at 5 {
-+ target-path = "/soc";
-+ __overlay__ {
-+ keypad: keypad {
-+ compatible = "gpio-keys";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&keypad_pins>;
-+ status = "disabled";
-+ autorepeat;
-+
-+ button at 17 {
-+ label = "GPIO KEY_UP";
-+ linux,code = <103>;
-+ gpios = <&gpio 17 0>;
-+ };
-+ button at 22 {
-+ label = "GPIO KEY_DOWN";
-+ linux,code = <108>;
-+ gpios = <&gpio 22 0>;
-+ };
-+ button at 27 {
-+ label = "GPIO KEY_LEFT";
-+ linux,code = <105>;
-+ gpios = <&gpio 27 0>;
-+ };
-+ button at 23 {
-+ label = "GPIO KEY_RIGHT";
-+ linux,code = <106>;
-+ gpios = <&gpio 23 0>;
-+ };
-+ button at 4 {
-+ label = "GPIO KEY_ENTER";
-+ linux,code = <28>;
-+ gpios = <&gpio 4 0>;
-+ };
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ speed = <&tinylcd35>,"spi-max-frequency:0";
-+ rotate = <&tinylcd35>,"rotate:0";
-+ fps = <&tinylcd35>,"fps:0";
-+ debug = <&tinylcd35>,"debug:0";
-+ touch = <&tinylcd35_ts>,"status";
-+ touchgpio = <&tinylcd35_ts_pins>,"brcm,pins:0",
-+ <&tinylcd35_ts>,"interrupts:0",
-+ <&tinylcd35_ts>,"pendown-gpio:4";
-+ xohms = <&tinylcd35_ts>,"ti,x-plate-ohms;0";
-+ rtc-pcf = <&i2c1>,"status",
-+ <&pcf8563>,"status";
-+ rtc-ds = <&i2c1>,"status",
-+ <&ds1307>,"status";
-+ keypad = <&keypad>,"status";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/uart1-overlay.dts
-@@ -0,0 +1,38 @@
-+/dts-v1/;
-+/plugin/;
-+
-+/{
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&uart1>;
-+ __overlay__ {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&uart1_pins>;
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ uart1_pins: uart1_pins {
-+ brcm,pins = <14 15>;
-+ brcm,function = <2>; /* alt5 */
-+ brcm,pull = <0 2>;
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target-path = "/chosen";
-+ __overlay__ {
-+ bootargs = "8250.nr_uarts=1";
-+ };
-+ };
-+
-+ __overrides__ {
-+ txd1_pin = <&uart1_pins>,"brcm,pins:0";
-+ rxd1_pin = <&uart1_pins>,"brcm,pins:4";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/vga666-overlay.dts
-@@ -0,0 +1,30 @@
-+/dts-v1/;
-+/plugin/;
-+
-+/{
-+ compatible = "brcm,bcm2708";
-+
-+ // There is no VGA driver module, but we need a platform device
-+ // node (that doesn't already use pinctrl) to hang the pinctrl
-+ // reference on - leds will do
-+
-+ fragment at 0 {
-+ target = <&leds>;
-+ __overlay__ {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&vga666_pins>;
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ vga666_pins: vga666_pins {
-+ brcm,pins = <2 3 4 5 6 7 8 9 10 11 12
-+ 13 14 15 16 17 18 19 20 21>;
-+ brcm,function = <6>; /* alt2 */
-+ brcm,pull = <0>; /* no pull */
-+ };
-+ };
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/w1-gpio-overlay.dts
-@@ -0,0 +1,39 @@
-+// Definitions for w1-gpio module (without external pullup)
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target-path = "/";
-+ __overlay__ {
-+
-+ w1: onewire at 0 {
-+ compatible = "w1-gpio";
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&w1_pins>;
-+ gpios = <&gpio 4 0>;
-+ rpi,parasitic-power = <0>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ w1_pins: w1_pins {
-+ brcm,pins = <4>;
-+ brcm,function = <0>; // in (initially)
-+ brcm,pull = <0>; // off
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ gpiopin = <&w1>,"gpios:4",
-+ <&w1_pins>,"brcm,pins:0";
-+ pullup = <&w1>,"rpi,parasitic-power:0";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/w1-gpio-pullup-overlay.dts
-@@ -0,0 +1,41 @@
-+// Definitions for w1-gpio module (with external pullup)
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target-path = "/";
-+ __overlay__ {
-+
-+ w1: onewire at 0 {
-+ compatible = "w1-gpio";
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&w1_pins>;
-+ gpios = <&gpio 4 0>, <&gpio 5 1>;
-+ rpi,parasitic-power = <0>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ w1_pins: w1_pins {
-+ brcm,pins = <4 5>;
-+ brcm,function = <0 1>; // in out
-+ brcm,pull = <0 0>; // off off
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ gpiopin = <&w1>,"gpios:4",
-+ <&w1_pins>,"brcm,pins:0";
-+ extpullup = <&w1>,"gpios:16",
-+ <&w1_pins>,"brcm,pins:4";
-+ pullup = <&w1>,"rpi,parasitic-power:0";
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0052-bcm2835-Match-with-BCM2708-Device-Trees.patch b/target/linux/brcm2708/patches-4.4/0052-bcm2835-Match-with-BCM2708-Device-Trees.patch
deleted file mode 100644
index f51929c..0000000
--- a/target/linux/brcm2708/patches-4.4/0052-bcm2835-Match-with-BCM2708-Device-Trees.patch
+++ /dev/null
@@ -1,515 +0,0 @@
-From f24cdbd260fb91b52c2b32301713f2d0de7e15bc Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Noralf=20Tr=C3=B8nnes?= <noralf at tronnes.org>
-Date: Sat, 15 Aug 2015 20:47:07 +0200
-Subject: [PATCH] bcm2835: Match with BCM2708 Device Trees
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
----
- arch/arm/boot/dts/bcm2835-rpi-b-plus.dts | 132 ++++++++++++++++++---
- arch/arm/boot/dts/bcm2835-rpi-b.dts | 115 ++++++++++++++++--
- arch/arm/boot/dts/bcm2835.dtsi | 195 +++----------------------------
- 3 files changed, 237 insertions(+), 205 deletions(-)
-
---- a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts
-+++ b/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts
-@@ -1,30 +1,128 @@
- /dts-v1/;
--#include "bcm2835-rpi.dtsi"
-+#include "bcm2835.dtsi"
-
- / {
- compatible = "raspberrypi,model-b-plus", "brcm,bcm2835";
- model = "Raspberry Pi Model B+";
--
-- leds {
-- act {
-- gpios = <&gpio 47 0>;
-- };
--
-- pwr {
-- label = "PWR";
-- gpios = <&gpio 35 0>;
-- default-state = "keep";
-- linux,default-trigger = "default-on";
-- };
-- };
- };
-
- &gpio {
-- pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>;
-+ spi0_pins: spi0_pins {
-+ brcm,pins = <7 8 9 10 11>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+
-+ i2c0_pins: i2c0 {
-+ brcm,pins = <0 1>;
-+ brcm,function = <4>;
-+ };
-
-- /* I2S interface */
-- i2s_alt0: i2s_alt0 {
-+ i2c1_pins: i2c1 {
-+ brcm,pins = <2 3>;
-+ brcm,function = <4>;
-+ };
-+
-+ i2s_pins: i2s {
- brcm,pins = <18 19 20 21>;
-- brcm,function = <BCM2835_FSEL_ALT0>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+};
-+
-+&mmc {
-+ status = "okay";
-+ bus-width = <4>;
-+};
-+
-+&fb {
-+ status = "okay";
-+};
-+
-+&uart0 {
-+ status = "okay";
-+};
-+
-+&spi0 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&spi0_pins>;
-+
-+ spidev at 0{
-+ compatible = "spidev";
-+ reg = <0>; /* CE0 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ };
-+
-+ spidev at 1{
-+ compatible = "spidev";
-+ reg = <1>; /* CE1 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ };
-+};
-+
-+&i2c0 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2c0_pins>;
-+ clock-frequency = <100000>;
-+};
-+
-+&i2c1 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2c1_pins>;
-+ clock-frequency = <100000>;
-+};
-+
-+&i2c2 {
-+ clock-frequency = <100000>;
-+};
-+
-+&i2s {
-+ #sound-dai-cells = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2s_pins>;
-+};
-+
-+&leds {
-+ act_led: act {
-+ label = "led0";
-+ linux,default-trigger = "mmc0";
-+ gpios = <&gpio 47 0>;
-+ };
-+
-+ pwr_led: pwr {
-+ label = "led1";
-+ linux,default-trigger = "input";
-+ gpios = <&gpio 35 0>;
-+ };
-+};
-+
-+/ {
-+ __overrides__ {
-+ uart0 = <&uart0>,"status";
-+ uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
-+ uart1_clkrate = <&uart1>,"clock-frequency:0";
-+ i2s = <&i2s>,"status";
-+ spi = <&spi0>,"status";
-+ i2c0 = <&i2c0>,"status";
-+ i2c1 = <&i2c1>,"status";
-+ i2c2_iknowwhatimdoing = <&i2c2>,"status";
-+ i2c0_baudrate = <&i2c0>,"clock-frequency:0";
-+ i2c1_baudrate = <&i2c1>,"clock-frequency:0";
-+ i2c2_baudrate = <&i2c2>,"clock-frequency:0";
-+ core_freq = <&clk_core>,"clock-frequency:0";
-+
-+ act_led_gpio = <&act_led>,"gpios:4";
-+ act_led_activelow = <&act_led>,"gpios:8";
-+ act_led_trigger = <&act_led>,"linux,default-trigger";
-+
-+ pwr_led_gpio = <&pwr_led>,"gpios:4";
-+ pwr_led_activelow = <&pwr_led>,"gpios:8";
-+ pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
-+
-+ audio = <&audio>,"status";
-+ watchdog = <&watchdog>,"status";
-+ random = <&random>,"status";
- };
- };
---- a/arch/arm/boot/dts/bcm2835-rpi-b.dts
-+++ b/arch/arm/boot/dts/bcm2835-rpi-b.dts
-@@ -1,17 +1,118 @@
- /dts-v1/;
--#include "bcm2835-rpi.dtsi"
-+#include "bcm2835.dtsi"
-
- / {
- compatible = "raspberrypi,model-b", "brcm,bcm2835";
- model = "Raspberry Pi Model B";
-+};
-
-- leds {
-- act {
-- gpios = <&gpio 16 1>;
-- };
-+&gpio {
-+ spi0_pins: spi0_pins {
-+ brcm,pins = <7 8 9 10 11>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+
-+ i2c0_pins: i2c0 {
-+ brcm,pins = <0 1>;
-+ brcm,function = <4>;
-+ };
-+
-+ i2c1_pins: i2c1 {
-+ brcm,pins = <2 3>;
-+ brcm,function = <4>;
-+ };
-+
-+ i2s_pins: i2s {
-+ brcm,pins = <28 29 30 31>;
-+ brcm,function = <6>; /* alt2 */
- };
- };
-
--&gpio {
-- pinctrl-0 = <&gpioout &alt0 &alt3>;
-+&mmc {
-+ status = "okay";
-+ bus-width = <4>;
-+};
-+
-+&fb {
-+ status = "okay";
-+};
-+
-+&uart0 {
-+ status = "okay";
-+};
-+
-+&spi0 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&spi0_pins>;
-+
-+ spidev at 0{
-+ compatible = "spidev";
-+ reg = <0>; /* CE0 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ };
-+
-+ spidev at 1{
-+ compatible = "spidev";
-+ reg = <1>; /* CE1 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ };
-+};
-+
-+&i2c0 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2c0_pins>;
-+ clock-frequency = <100000>;
-+};
-+
-+&i2c1 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2c1_pins>;
-+ clock-frequency = <100000>;
-+};
-+
-+&i2c2 {
-+ clock-frequency = <100000>;
-+};
-+
-+&i2s {
-+ #sound-dai-cells = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2s_pins>;
-+};
-+
-+&leds {
-+ act_led: act {
-+ label = "led0";
-+ linux,default-trigger = "mmc0";
-+ gpios = <&gpio 16 1>;
-+ };
-+};
-+
-+/ {
-+ __overrides__ {
-+ uart0 = <&uart0>,"status";
-+ uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
-+ uart1_clkrate = <&uart1>,"clock-frequency:0";
-+ i2s = <&i2s>,"status";
-+ spi = <&spi0>,"status";
-+ i2c0 = <&i2c0>,"status";
-+ i2c1 = <&i2c1>,"status";
-+ i2c2_iknowwhatimdoing = <&i2c2>,"status";
-+ i2c0_baudrate = <&i2c0>,"clock-frequency:0";
-+ i2c1_baudrate = <&i2c1>,"clock-frequency:0";
-+ i2c2_baudrate = <&i2c2>,"clock-frequency:0";
-+ core_freq = <&clk_core>,"clock-frequency:0";
-+
-+ act_led_gpio = <&act_led>,"gpios:4";
-+ act_led_activelow = <&act_led>,"gpios:8";
-+ act_led_trigger = <&act_led>,"linux,default-trigger";
-+
-+ audio = <&audio>,"status";
-+ watchdog = <&watchdog>,"status";
-+ random = <&random>,"status";
-+ };
- };
---- a/arch/arm/boot/dts/bcm2835.dtsi
-+++ b/arch/arm/boot/dts/bcm2835.dtsi
-@@ -1,206 +1,39 @@
--#include <dt-bindings/pinctrl/bcm2835.h>
--#include <dt-bindings/clock/bcm2835.h>
--#include "skeleton.dtsi"
-+#include "bcm2708_common.dtsi"
-
- / {
- compatible = "brcm,bcm2835";
- model = "BCM2835";
-- interrupt-parent = <&intc>;
-
- chosen {
-- bootargs = "earlyprintk console=ttyAMA0";
-+ bootargs = "";
- };
-
- soc {
-- compatible = "simple-bus";
-- #address-cells = <1>;
-- #size-cells = <1>;
-- ranges = <0x7e000000 0x20000000 0x02000000>;
-+ ranges = <0x7e000000 0x20000000 0x01000000>;
- dma-ranges = <0x40000000 0x00000000 0x20000000>;
-
- timer at 7e003000 {
- compatible = "brcm,bcm2835-system-timer";
- reg = <0x7e003000 0x1000>;
- interrupts = <1 0>, <1 1>, <1 2>, <1 3>;
-- /* This could be a reference to BCM2835_CLOCK_TIMER,
-- * but we don't have the driver using the common clock
-- * support yet.
-- */
- clock-frequency = <1000000>;
- };
-
-- dma: dma at 7e007000 {
-- compatible = "brcm,bcm2835-dma";
-- reg = <0x7e007000 0xf00>;
-- interrupts = <1 16>,
-- <1 17>,
-- <1 18>,
-- <1 19>,
-- <1 20>,
-- <1 21>,
-- <1 22>,
-- <1 23>,
-- <1 24>,
-- <1 25>,
-- <1 26>,
-- <1 27>,
-- <1 28>;
--
-- #dma-cells = <1>;
-- brcm,dma-channel-mask = <0x7f35>;
-- };
--
-- intc: interrupt-controller at 7e00b200 {
-- compatible = "brcm,bcm2835-armctrl-ic";
-- reg = <0x7e00b200 0x200>;
-- interrupt-controller;
-- #interrupt-cells = <2>;
-- };
--
-- watchdog at 7e100000 {
-- compatible = "brcm,bcm2835-pm-wdt";
-- reg = <0x7e100000 0x28>;
-- };
--
-- clocks: cprman at 7e101000 {
-- compatible = "brcm,bcm2835-cprman";
-- #clock-cells = <1>;
-- reg = <0x7e101000 0x2000>;
--
-- /* CPRMAN derives everything from the platform's
-- * oscillator.
-- */
-- clocks = <&clk_osc>;
-- };
--
-- rng at 7e104000 {
-- compatible = "brcm,bcm2835-rng";
-- reg = <0x7e104000 0x10>;
-- };
--
-- mailbox: mailbox at 7e00b800 {
-- compatible = "brcm,bcm2835-mbox";
-- reg = <0x7e00b880 0x40>;
-- interrupts = <0 1>;
-- #mbox-cells = <0>;
-- };
--
-- gpio: gpio at 7e200000 {
-- compatible = "brcm,bcm2835-gpio";
-- reg = <0x7e200000 0xb4>;
-- /*
-- * The GPIO IP block is designed for 3 banks of GPIOs.
-- * Each bank has a GPIO interrupt for itself.
-- * There is an overall "any bank" interrupt.
-- * In order, these are GIC interrupts 17, 18, 19, 20.
-- * Since the BCM2835 only has 2 banks, the 2nd bank
-- * interrupt output appears to be mirrored onto the
-- * 3rd bank's interrupt signal.
-- * So, a bank0 interrupt shows up on 17, 20, and
-- * a bank1 interrupt shows up on 18, 19, 20!
-- */
-- interrupts = <2 17>, <2 18>, <2 19>, <2 20>;
--
-- gpio-controller;
-- #gpio-cells = <2>;
--
-- interrupt-controller;
-- #interrupt-cells = <2>;
-- };
--
-- uart0: uart at 7e201000 {
-- compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell";
-- reg = <0x7e201000 0x1000>;
-- interrupts = <2 25>;
-- clocks = <&clocks BCM2835_CLOCK_UART>,
-- <&clocks BCM2835_CLOCK_VPU>;
-- clock-names = "uartclk", "apb_pclk";
-- arm,primecell-periphid = <0x00241011>;
-- };
--
-- i2s: i2s at 7e203000 {
-- compatible = "brcm,bcm2835-i2s";
-- reg = <0x7e203000 0x24>,
-- <0x7e101098 0x08>;
--
-- dmas = <&dma 2>,
-- <&dma 3>;
-- dma-names = "tx", "rx";
-- status = "disabled";
-- };
--
-- spi: spi at 7e204000 {
-- compatible = "brcm,bcm2835-spi";
-- reg = <0x7e204000 0x1000>;
-- interrupts = <2 22>;
-- clocks = <&clocks BCM2835_CLOCK_VPU>;
-- #address-cells = <1>;
-- #size-cells = <0>;
-- status = "disabled";
-- };
--
-- i2c0: i2c at 7e205000 {
-- compatible = "brcm,bcm2835-i2c";
-- reg = <0x7e205000 0x1000>;
-- interrupts = <2 21>;
-- clocks = <&clocks BCM2835_CLOCK_VPU>;
-- #address-cells = <1>;
-- #size-cells = <0>;
-- status = "disabled";
-- };
--
-- sdhci: sdhci at 7e300000 {
-- compatible = "brcm,bcm2835-sdhci";
-- reg = <0x7e300000 0x100>;
-- interrupts = <2 30>;
-- clocks = <&clocks BCM2835_CLOCK_EMMC>;
-- status = "disabled";
-- };
--
-- i2c1: i2c at 7e804000 {
-- compatible = "brcm,bcm2835-i2c";
-- reg = <0x7e804000 0x1000>;
-- interrupts = <2 21>;
-- clocks = <&clocks BCM2835_CLOCK_VPU>;
-- #address-cells = <1>;
-- #size-cells = <0>;
-- status = "disabled";
-- };
--
-- i2c2: i2c at 7e805000 {
-- compatible = "brcm,bcm2835-i2c";
-- reg = <0x7e805000 0x1000>;
-- interrupts = <2 21>;
-- clocks = <&clocks BCM2835_CLOCK_VPU>;
-- #address-cells = <1>;
-- #size-cells = <0>;
-- status = "disabled";
-- };
--
-- usb at 7e980000 {
-- compatible = "brcm,bcm2835-usb";
-- reg = <0x7e980000 0x10000>;
-- interrupts = <1 9>;
-- };
--
- arm-pmu {
- compatible = "arm,arm1176-pmu";
- };
-- };
-
-- clocks {
-- compatible = "simple-bus";
-- #address-cells = <1>;
-- #size-cells = <0>;
--
-- /* The oscillator is the root of the clock tree. */
-- clk_osc: clock at 3 {
-- compatible = "fixed-clock";
-- reg = <3>;
-- #clock-cells = <0>;
-- clock-output-names = "osc";
-- clock-frequency = <19200000>;
-+ aux_enable: aux_enable at 0x7e215004 {
-+ compatible = "bcrm,bcm2835-aux-enable";
-+ reg = <0x7e215004 0x04>;
- };
--
- };
- };
-+
-+&intc {
-+ compatible = "brcm,bcm2835-armctrl-ic";
-+};
-+
-+&watchdog {
-+ status = "okay";
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0053-fbdev-add-FBIOCOPYAREA-ioctl.patch b/target/linux/brcm2708/patches-4.4/0053-fbdev-add-FBIOCOPYAREA-ioctl.patch
deleted file mode 100644
index 8d76149..0000000
--- a/target/linux/brcm2708/patches-4.4/0053-fbdev-add-FBIOCOPYAREA-ioctl.patch
+++ /dev/null
@@ -1,91 +0,0 @@
-From c5faa0d81a4cace1024a0c72c164c814b22d5499 Mon Sep 17 00:00:00 2001
-From: Siarhei Siamashka <siarhei.siamashka at gmail.com>
-Date: Mon, 17 Jun 2013 13:32:11 +0300
-Subject: [PATCH] fbdev: add FBIOCOPYAREA ioctl
-
-Based on the patch authored by Ali Gholami Rudi at
- https://lkml.org/lkml/2009/7/13/153
-
-Provide an ioctl for userspace applications, but only if this operation
-is hardware accelerated (otherwide it does not make any sense).
-
-Signed-off-by: Siarhei Siamashka <siarhei.siamashka at gmail.com>
----
- drivers/video/fbdev/core/fbmem.c | 30 ++++++++++++++++++++++++++++++
- include/uapi/linux/fb.h | 5 +++++
- 2 files changed, 35 insertions(+)
-
---- a/drivers/video/fbdev/core/fbmem.c
-+++ b/drivers/video/fbdev/core/fbmem.c
-@@ -1084,6 +1084,25 @@ fb_blank(struct fb_info *info, int blank
- }
- EXPORT_SYMBOL(fb_blank);
-
-+static int fb_copyarea_user(struct fb_info *info,
-+ struct fb_copyarea *copy)
-+{
-+ int ret = 0;
-+ if (!lock_fb_info(info))
-+ return -ENODEV;
-+ if (copy->dx + copy->width > info->var.xres ||
-+ copy->sx + copy->width > info->var.xres ||
-+ copy->dy + copy->height > info->var.yres ||
-+ copy->sy + copy->height > info->var.yres) {
-+ ret = -EINVAL;
-+ goto out;
-+ }
-+ info->fbops->fb_copyarea(info, copy);
-+out:
-+ unlock_fb_info(info);
-+ return ret;
-+}
-+
- static long do_fb_ioctl(struct fb_info *info, unsigned int cmd,
- unsigned long arg)
- {
-@@ -1094,6 +1113,7 @@ static long do_fb_ioctl(struct fb_info *
- struct fb_cmap cmap_from;
- struct fb_cmap_user cmap;
- struct fb_event event;
-+ struct fb_copyarea copy;
- void __user *argp = (void __user *)arg;
- long ret = 0;
-
-@@ -1211,6 +1231,15 @@ static long do_fb_ioctl(struct fb_info *
- unlock_fb_info(info);
- console_unlock();
- break;
-+ case FBIOCOPYAREA:
-+ if (info->flags & FBINFO_HWACCEL_COPYAREA) {
-+ /* only provide this ioctl if it is accelerated */
-+ if (copy_from_user(©, argp, sizeof(copy)))
-+ return -EFAULT;
-+ ret = fb_copyarea_user(info, ©);
-+ break;
-+ }
-+ /* fall through */
- default:
- if (!lock_fb_info(info))
- return -ENODEV;
-@@ -1365,6 +1394,7 @@ static long fb_compat_ioctl(struct file
- case FBIOPAN_DISPLAY:
- case FBIOGET_CON2FBMAP:
- case FBIOPUT_CON2FBMAP:
-+ case FBIOCOPYAREA:
- arg = (unsigned long) compat_ptr(arg);
- case FBIOBLANK:
- ret = do_fb_ioctl(info, cmd, arg);
---- a/include/uapi/linux/fb.h
-+++ b/include/uapi/linux/fb.h
-@@ -34,6 +34,11 @@
- #define FBIOPUT_MODEINFO 0x4617
- #define FBIOGET_DISPINFO 0x4618
- #define FBIO_WAITFORVSYNC _IOW('F', 0x20, __u32)
-+/*
-+ * HACK: use 'z' in order not to clash with any other ioctl numbers which might
-+ * be concurrently added to the mainline kernel
-+ */
-+#define FBIOCOPYAREA _IOW('z', 0x21, struct fb_copyarea)
-
- #define FB_TYPE_PACKED_PIXELS 0 /* Packed Pixels */
- #define FB_TYPE_PLANES 1 /* Non interleaved planes */
diff --git a/target/linux/brcm2708/patches-4.4/0057-Speed-up-console-framebuffer-imageblit-function.patch b/target/linux/brcm2708/patches-4.4/0057-Speed-up-console-framebuffer-imageblit-function.patch
deleted file mode 100644
index 8973c4a..0000000
--- a/target/linux/brcm2708/patches-4.4/0057-Speed-up-console-framebuffer-imageblit-function.patch
+++ /dev/null
@@ -1,209 +0,0 @@
-From da5e26ea79aeb2adf8ed29311a62052ebe781a66 Mon Sep 17 00:00:00 2001
-From: Harm Hanemaaijer <fgenfb at yahoo.com>
-Date: Thu, 20 Jun 2013 20:21:39 +0200
-Subject: [PATCH] Speed up console framebuffer imageblit function
-
-Especially on platforms with a slower CPU but a relatively high
-framebuffer fill bandwidth, like current ARM devices, the existing
-console monochrome imageblit function used to draw console text is
-suboptimal for common pixel depths such as 16bpp and 32bpp. The existing
-code is quite general and can deal with several pixel depths. By creating
-special case functions for 16bpp and 32bpp, by far the most common pixel
-formats used on modern systems, a significant speed-up is attained
-which can be readily felt on ARM-based devices like the Raspberry Pi
-and the Allwinner platform, but should help any platform using the
-fb layer.
-
-The special case functions allow constant folding, eliminating a number
-of instructions including divide operations, and allow the use of an
-unrolled loop, eliminating instructions with a variable shift size,
-reducing source memory access instructions, and eliminating excessive
-branching. These unrolled loops also allow much better code optimization
-by the C compiler. The code that selects which optimized variant is used
-is also simplified, eliminating integer divide instructions.
-
-The speed-up, measured by timing 'cat file.txt' in the console, varies
-between 40% and 70%, when testing on the Raspberry Pi and Allwinner
-ARM-based platforms, depending on font size and the pixel depth, with
-the greater benefit for 32bpp.
-
-Signed-off-by: Harm Hanemaaijer <fgenfb at yahoo.com>
----
- drivers/video/fbdev/core/cfbimgblt.c | 152 +++++++++++++++++++++++++++++++++--
- 1 file changed, 147 insertions(+), 5 deletions(-)
-
---- a/drivers/video/fbdev/core/cfbimgblt.c
-+++ b/drivers/video/fbdev/core/cfbimgblt.c
-@@ -28,6 +28,11 @@
- *
- * Also need to add code to deal with cards endians that are different than
- * the native cpu endians. I also need to deal with MSB position in the word.
-+ * Modified by Harm Hanemaaijer (fgenfb at yahoo.com) 2013:
-+ * - Provide optimized versions of fast_imageblit for 16 and 32bpp that are
-+ * significantly faster than the previous implementation.
-+ * - Simplify the fast/slow_imageblit selection code, avoiding integer
-+ * divides.
- */
- #include <linux/module.h>
- #include <linux/string.h>
-@@ -262,6 +267,133 @@ static inline void fast_imageblit(const
- }
- }
-
-+/*
-+ * Optimized fast_imageblit for bpp == 16. ppw = 2, bit_mask = 3 folded
-+ * into the code, main loop unrolled.
-+ */
-+
-+static inline void fast_imageblit16(const struct fb_image *image,
-+ struct fb_info *p, u8 __iomem * dst1,
-+ u32 fgcolor, u32 bgcolor)
-+{
-+ u32 fgx = fgcolor, bgx = bgcolor;
-+ u32 spitch = (image->width + 7) / 8;
-+ u32 end_mask, eorx;
-+ const char *s = image->data, *src;
-+ u32 __iomem *dst;
-+ const u32 *tab = NULL;
-+ int i, j, k;
-+
-+ tab = fb_be_math(p) ? cfb_tab16_be : cfb_tab16_le;
-+
-+ fgx <<= 16;
-+ bgx <<= 16;
-+ fgx |= fgcolor;
-+ bgx |= bgcolor;
-+
-+ eorx = fgx ^ bgx;
-+ k = image->width / 2;
-+
-+ for (i = image->height; i--;) {
-+ dst = (u32 __iomem *) dst1;
-+ src = s;
-+
-+ j = k;
-+ while (j >= 4) {
-+ u8 bits = *src;
-+ end_mask = tab[(bits >> 6) & 3];
-+ FB_WRITEL((end_mask & eorx) ^ bgx, dst++);
-+ end_mask = tab[(bits >> 4) & 3];
-+ FB_WRITEL((end_mask & eorx) ^ bgx, dst++);
-+ end_mask = tab[(bits >> 2) & 3];
-+ FB_WRITEL((end_mask & eorx) ^ bgx, dst++);
-+ end_mask = tab[bits & 3];
-+ FB_WRITEL((end_mask & eorx) ^ bgx, dst++);
-+ src++;
-+ j -= 4;
-+ }
-+ if (j != 0) {
-+ u8 bits = *src;
-+ end_mask = tab[(bits >> 6) & 3];
-+ FB_WRITEL((end_mask & eorx) ^ bgx, dst++);
-+ if (j >= 2) {
-+ end_mask = tab[(bits >> 4) & 3];
-+ FB_WRITEL((end_mask & eorx) ^ bgx, dst++);
-+ if (j == 3) {
-+ end_mask = tab[(bits >> 2) & 3];
-+ FB_WRITEL((end_mask & eorx) ^ bgx, dst);
-+ }
-+ }
-+ }
-+ dst1 += p->fix.line_length;
-+ s += spitch;
-+ }
-+}
-+
-+/*
-+ * Optimized fast_imageblit for bpp == 32. ppw = 1, bit_mask = 1 folded
-+ * into the code, main loop unrolled.
-+ */
-+
-+static inline void fast_imageblit32(const struct fb_image *image,
-+ struct fb_info *p, u8 __iomem * dst1,
-+ u32 fgcolor, u32 bgcolor)
-+{
-+ u32 fgx = fgcolor, bgx = bgcolor;
-+ u32 spitch = (image->width + 7) / 8;
-+ u32 end_mask, eorx;
-+ const char *s = image->data, *src;
-+ u32 __iomem *dst;
-+ const u32 *tab = NULL;
-+ int i, j, k;
-+
-+ tab = cfb_tab32;
-+
-+ eorx = fgx ^ bgx;
-+ k = image->width;
-+
-+ for (i = image->height; i--;) {
-+ dst = (u32 __iomem *) dst1;
-+ src = s;
-+
-+ j = k;
-+ while (j >= 8) {
-+ u8 bits = *src;
-+ end_mask = tab[(bits >> 7) & 1];
-+ FB_WRITEL((end_mask & eorx) ^ bgx, dst++);
-+ end_mask = tab[(bits >> 6) & 1];
-+ FB_WRITEL((end_mask & eorx) ^ bgx, dst++);
-+ end_mask = tab[(bits >> 5) & 1];
-+ FB_WRITEL((end_mask & eorx) ^ bgx, dst++);
-+ end_mask = tab[(bits >> 4) & 1];
-+ FB_WRITEL((end_mask & eorx) ^ bgx, dst++);
-+ end_mask = tab[(bits >> 3) & 1];
-+ FB_WRITEL((end_mask & eorx) ^ bgx, dst++);
-+ end_mask = tab[(bits >> 2) & 1];
-+ FB_WRITEL((end_mask & eorx) ^ bgx, dst++);
-+ end_mask = tab[(bits >> 1) & 1];
-+ FB_WRITEL((end_mask & eorx) ^ bgx, dst++);
-+ end_mask = tab[bits & 1];
-+ FB_WRITEL((end_mask & eorx) ^ bgx, dst++);
-+ src++;
-+ j -= 8;
-+ }
-+ if (j != 0) {
-+ u32 bits = (u32) * src;
-+ while (j > 1) {
-+ end_mask = tab[(bits >> 7) & 1];
-+ FB_WRITEL((end_mask & eorx) ^ bgx, dst++);
-+ bits <<= 1;
-+ j--;
-+ }
-+ end_mask = tab[(bits >> 7) & 1];
-+ FB_WRITEL((end_mask & eorx) ^ bgx, dst);
-+ }
-+ dst1 += p->fix.line_length;
-+ s += spitch;
-+ }
-+}
-+
- void cfb_imageblit(struct fb_info *p, const struct fb_image *image)
- {
- u32 fgcolor, bgcolor, start_index, bitstart, pitch_index = 0;
-@@ -294,11 +426,21 @@ void cfb_imageblit(struct fb_info *p, co
- bgcolor = image->bg_color;
- }
-
-- if (32 % bpp == 0 && !start_index && !pitch_index &&
-- ((width & (32/bpp-1)) == 0) &&
-- bpp >= 8 && bpp <= 32)
-- fast_imageblit(image, p, dst1, fgcolor, bgcolor);
-- else
-+ if (!start_index && !pitch_index) {
-+ if (bpp == 32)
-+ fast_imageblit32(image, p, dst1, fgcolor,
-+ bgcolor);
-+ else if (bpp == 16 && (width & 1) == 0)
-+ fast_imageblit16(image, p, dst1, fgcolor,
-+ bgcolor);
-+ else if (bpp == 8 && (width & 3) == 0)
-+ fast_imageblit(image, p, dst1, fgcolor,
-+ bgcolor);
-+ else
-+ slow_imageblit(image, p, dst1, fgcolor,
-+ bgcolor,
-+ start_index, pitch_index);
-+ } else
- slow_imageblit(image, p, dst1, fgcolor, bgcolor,
- start_index, pitch_index);
- } else
diff --git a/target/linux/brcm2708/patches-4.4/0058-Allow-mac-address-to-be-set-in-smsc95xx.patch b/target/linux/brcm2708/patches-4.4/0058-Allow-mac-address-to-be-set-in-smsc95xx.patch
deleted file mode 100644
index 11b7232..0000000
--- a/target/linux/brcm2708/patches-4.4/0058-Allow-mac-address-to-be-set-in-smsc95xx.patch
+++ /dev/null
@@ -1,91 +0,0 @@
-From aa149fc2bc1501cda2a3ddbecd41bf8f3d1bf9fe Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Tue, 26 Mar 2013 17:26:38 +0000
-Subject: [PATCH] Allow mac address to be set in smsc95xx
-
-Signed-off-by: popcornmix <popcornmix at gmail.com>
----
- drivers/net/usb/smsc95xx.c | 56 ++++++++++++++++++++++++++++++++++++++++++++++
- 1 file changed, 56 insertions(+)
-
---- a/drivers/net/usb/smsc95xx.c
-+++ b/drivers/net/usb/smsc95xx.c
-@@ -59,6 +59,7 @@
- #define SUSPEND_SUSPEND3 (0x08)
- #define SUSPEND_ALLMODES (SUSPEND_SUSPEND0 | SUSPEND_SUSPEND1 | \
- SUSPEND_SUSPEND2 | SUSPEND_SUSPEND3)
-+#define MAC_ADDR_LEN (6)
-
- struct smsc95xx_priv {
- u32 mac_cr;
-@@ -74,6 +75,10 @@ static bool turbo_mode = false;
- module_param(turbo_mode, bool, 0644);
- MODULE_PARM_DESC(turbo_mode, "Enable multiple frames per Rx transaction");
-
-+static char *macaddr = ":";
-+module_param(macaddr, charp, 0);
-+MODULE_PARM_DESC(macaddr, "MAC address");
-+
- static int __must_check __smsc95xx_read_reg(struct usbnet *dev, u32 index,
- u32 *data, int in_pm)
- {
-@@ -763,8 +768,59 @@ static int smsc95xx_ioctl(struct net_dev
- return generic_mii_ioctl(&dev->mii, if_mii(rq), cmd, NULL);
- }
-
-+/* Check the macaddr module parameter for a MAC address */
-+static int smsc95xx_is_macaddr_param(struct usbnet *dev, u8 *dev_mac)
-+{
-+ int i, j, got_num, num;
-+ u8 mtbl[MAC_ADDR_LEN];
-+
-+ if (macaddr[0] == ':')
-+ return 0;
-+
-+ i = 0;
-+ j = 0;
-+ num = 0;
-+ got_num = 0;
-+ while (j < MAC_ADDR_LEN) {
-+ if (macaddr[i] && macaddr[i] != ':') {
-+ got_num++;
-+ if ('0' <= macaddr[i] && macaddr[i] <= '9')
-+ num = num * 16 + macaddr[i] - '0';
-+ else if ('A' <= macaddr[i] && macaddr[i] <= 'F')
-+ num = num * 16 + 10 + macaddr[i] - 'A';
-+ else if ('a' <= macaddr[i] && macaddr[i] <= 'f')
-+ num = num * 16 + 10 + macaddr[i] - 'a';
-+ else
-+ break;
-+ i++;
-+ } else if (got_num == 2) {
-+ mtbl[j++] = (u8) num;
-+ num = 0;
-+ got_num = 0;
-+ i++;
-+ } else {
-+ break;
-+ }
-+ }
-+
-+ if (j == MAC_ADDR_LEN) {
-+ netif_dbg(dev, ifup, dev->net, "Overriding MAC address with: "
-+ "%02x:%02x:%02x:%02x:%02x:%02x\n", mtbl[0], mtbl[1], mtbl[2],
-+ mtbl[3], mtbl[4], mtbl[5]);
-+ for (i = 0; i < MAC_ADDR_LEN; i++)
-+ dev_mac[i] = mtbl[i];
-+ return 1;
-+ } else {
-+ return 0;
-+ }
-+}
-+
- static void smsc95xx_init_mac_address(struct usbnet *dev)
- {
-+ /* Check module parameters */
-+ if (smsc95xx_is_macaddr_param(dev, dev->net->dev_addr))
-+ return;
-+
- /* try reading mac address from EEPROM */
- if (smsc95xx_read_eeprom(dev, EEPROM_MAC_OFFSET, ETH_ALEN,
- dev->net->dev_addr) == 0) {
diff --git a/target/linux/brcm2708/patches-4.4/0059-enabling-the-realtime-clock-1-wire-chip-DS1307-and-1.patch b/target/linux/brcm2708/patches-4.4/0059-enabling-the-realtime-clock-1-wire-chip-DS1307-and-1.patch
deleted file mode 100644
index da5cc9b..0000000
--- a/target/linux/brcm2708/patches-4.4/0059-enabling-the-realtime-clock-1-wire-chip-DS1307-and-1.patch
+++ /dev/null
@@ -1,242 +0,0 @@
-From aff5ad81730ac8431067dc0fd530f56a32320705 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Wed, 8 May 2013 11:46:50 +0100
-Subject: [PATCH] enabling the realtime clock 1-wire chip DS1307 and 1-wire on
- GPIO4 (as a module)
-
-1-wire: Add support for configuring pin for w1-gpio kernel module
-See: https://github.com/raspberrypi/linux/pull/457
-
-Add bitbanging pullups, use them for w1-gpio
-
-Allows parasite power to work, uses module option pullup=1
-
-bcm2708: Ensure 1-wire pullup is disabled by default, and expose as module parameter
-
-Signed-off-by: Alex J Lennon <ajlennon at dynamicdevices.co.uk>
-
-w1-gpio: Add gpiopin module parameter and correctly free up gpio pull-up pin, if set
-
-Signed-off-by: Alex J Lennon <ajlennon at dynamicdevices.co.uk>
-
-w1-gpio: Sort out the pullup/parasitic power tangle
----
- drivers/w1/masters/w1-gpio.c | 69 ++++++++++++++++++++++++++++++++++++++++----
- drivers/w1/w1.h | 6 ++++
- drivers/w1/w1_int.c | 14 +++++++++
- drivers/w1/w1_io.c | 18 ++++++++++--
- include/linux/w1-gpio.h | 1 +
- 5 files changed, 99 insertions(+), 9 deletions(-)
-
---- a/drivers/w1/masters/w1-gpio.c
-+++ b/drivers/w1/masters/w1-gpio.c
-@@ -23,6 +23,19 @@
- #include "../w1.h"
- #include "../w1_int.h"
-
-+static int w1_gpio_pullup = 0;
-+static int w1_gpio_pullup_orig = 0;
-+module_param_named(pullup, w1_gpio_pullup, int, 0);
-+MODULE_PARM_DESC(pullup, "Enable parasitic power (power on data) mode");
-+static int w1_gpio_pullup_pin = -1;
-+static int w1_gpio_pullup_pin_orig = -1;
-+module_param_named(extpullup, w1_gpio_pullup_pin, int, 0);
-+MODULE_PARM_DESC(extpullup, "GPIO external pullup pin number");
-+static int w1_gpio_pin = -1;
-+static int w1_gpio_pin_orig = -1;
-+module_param_named(gpiopin, w1_gpio_pin, int, 0);
-+MODULE_PARM_DESC(gpiopin, "GPIO pin number");
-+
- static u8 w1_gpio_set_pullup(void *data, int delay)
- {
- struct w1_gpio_platform_data *pdata = data;
-@@ -67,6 +80,16 @@ static u8 w1_gpio_read_bit(void *data)
- return gpio_get_value(pdata->pin) ? 1 : 0;
- }
-
-+static void w1_gpio_bitbang_pullup(void *data, u8 on)
-+{
-+ struct w1_gpio_platform_data *pdata = data;
-+
-+ if (on)
-+ gpio_direction_output(pdata->pin, 1);
-+ else
-+ gpio_direction_input(pdata->pin);
-+}
-+
- #if defined(CONFIG_OF)
- static const struct of_device_id w1_gpio_dt_ids[] = {
- { .compatible = "w1-gpio" },
-@@ -80,6 +103,7 @@ static int w1_gpio_probe_dt(struct platf
- struct w1_gpio_platform_data *pdata = dev_get_platdata(&pdev->dev);
- struct device_node *np = pdev->dev.of_node;
- int gpio;
-+ u32 value;
-
- pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
- if (!pdata)
-@@ -88,6 +112,9 @@ static int w1_gpio_probe_dt(struct platf
- if (of_get_property(np, "linux,open-drain", NULL))
- pdata->is_open_drain = 1;
-
-+ if (of_property_read_u32(np, "rpi,parasitic-power", &value) == 0)
-+ pdata->parasitic_power = (value != 0);
-+
- gpio = of_get_gpio(np, 0);
- if (gpio < 0) {
- if (gpio != -EPROBE_DEFER)
-@@ -103,7 +130,7 @@ static int w1_gpio_probe_dt(struct platf
- if (gpio == -EPROBE_DEFER)
- return gpio;
- /* ignore other errors as the pullup gpio is optional */
-- pdata->ext_pullup_enable_pin = gpio;
-+ pdata->ext_pullup_enable_pin = (gpio >= 0) ? gpio : -1;
-
- pdev->dev.platform_data = pdata;
-
-@@ -113,13 +140,15 @@ static int w1_gpio_probe_dt(struct platf
- static int w1_gpio_probe(struct platform_device *pdev)
- {
- struct w1_bus_master *master;
-- struct w1_gpio_platform_data *pdata;
-+ struct w1_gpio_platform_data *pdata = pdev->dev.platform_data;
- int err;
-
-- if (of_have_populated_dt()) {
-- err = w1_gpio_probe_dt(pdev);
-- if (err < 0)
-- return err;
-+ if(pdata == NULL) {
-+ if (of_have_populated_dt()) {
-+ err = w1_gpio_probe_dt(pdev);
-+ if (err < 0)
-+ return err;
-+ }
- }
-
- pdata = dev_get_platdata(&pdev->dev);
-@@ -136,6 +165,22 @@ static int w1_gpio_probe(struct platform
- return -ENOMEM;
- }
-
-+ w1_gpio_pin_orig = pdata->pin;
-+ w1_gpio_pullup_pin_orig = pdata->ext_pullup_enable_pin;
-+ w1_gpio_pullup_orig = pdata->parasitic_power;
-+
-+ if(gpio_is_valid(w1_gpio_pin)) {
-+ pdata->pin = w1_gpio_pin;
-+ pdata->ext_pullup_enable_pin = -1;
-+ pdata->parasitic_power = -1;
-+ }
-+ pdata->parasitic_power |= w1_gpio_pullup;
-+ if(gpio_is_valid(w1_gpio_pullup_pin)) {
-+ pdata->ext_pullup_enable_pin = w1_gpio_pullup_pin;
-+ }
-+
-+ dev_info(&pdev->dev, "gpio pin %d, external pullup pin %d, parasitic power %d\n", pdata->pin, pdata->ext_pullup_enable_pin, pdata->parasitic_power);
-+
- err = devm_gpio_request(&pdev->dev, pdata->pin, "w1");
- if (err) {
- dev_err(&pdev->dev, "gpio_request (pin) failed\n");
-@@ -165,6 +210,14 @@ static int w1_gpio_probe(struct platform
- master->set_pullup = w1_gpio_set_pullup;
- }
-
-+ if (pdata->parasitic_power) {
-+ if (pdata->is_open_drain)
-+ printk(KERN_ERR "w1-gpio 'pullup'(parasitic power) "
-+ "option doesn't work with open drain GPIO\n");
-+ else
-+ master->bitbang_pullup = w1_gpio_bitbang_pullup;
-+ }
-+
- err = w1_add_master_device(master);
- if (err) {
- dev_err(&pdev->dev, "w1_add_master device failed\n");
-@@ -195,6 +248,10 @@ static int w1_gpio_remove(struct platfor
-
- w1_remove_master_device(master);
-
-+ pdata->pin = w1_gpio_pin_orig;
-+ pdata->ext_pullup_enable_pin = w1_gpio_pullup_pin_orig;
-+ pdata->parasitic_power = w1_gpio_pullup_orig;
-+
- return 0;
- }
-
---- a/drivers/w1/w1.h
-+++ b/drivers/w1/w1.h
-@@ -171,6 +171,12 @@ struct w1_bus_master
-
- u8 (*set_pullup)(void *, int);
-
-+ /**
-+ * Turns the pullup on/off in bitbanging mode, takes an on/off argument.
-+ * @return -1=Error, 0=completed
-+ */
-+ void (*bitbang_pullup) (void *, u8);
-+
- void (*search)(void *, struct w1_master *,
- u8, w1_slave_found_callback);
- };
---- a/drivers/w1/w1_int.c
-+++ b/drivers/w1/w1_int.c
-@@ -122,6 +122,20 @@ int w1_add_master_device(struct w1_bus_m
- return(-EINVAL);
- }
-
-+ /* bitbanging hardware uses bitbang_pullup, other hardware uses set_pullup
-+ * and takes care of timing itself */
-+ if (!master->write_byte && !master->touch_bit && master->set_pullup) {
-+ printk(KERN_ERR "w1_add_master_device: set_pullup requires "
-+ "write_byte or touch_bit, disabling\n");
-+ master->set_pullup = NULL;
-+ }
-+
-+ if (master->set_pullup && master->bitbang_pullup) {
-+ printk(KERN_ERR "w1_add_master_device: set_pullup should not "
-+ "be set when bitbang_pullup is used, disabling\n");
-+ master->set_pullup = NULL;
-+ }
-+
- /* Lock until the device is added (or not) to w1_masters. */
- mutex_lock(&w1_mlock);
- /* Search for the first available id (starting at 1). */
---- a/drivers/w1/w1_io.c
-+++ b/drivers/w1/w1_io.c
-@@ -134,10 +134,22 @@ static void w1_pre_write(struct w1_maste
- static void w1_post_write(struct w1_master *dev)
- {
- if (dev->pullup_duration) {
-- if (dev->enable_pullup && dev->bus_master->set_pullup)
-- dev->bus_master->set_pullup(dev->bus_master->data, 0);
-- else
-+ if (dev->enable_pullup) {
-+ if (dev->bus_master->set_pullup) {
-+ dev->bus_master->set_pullup(dev->
-+ bus_master->data,
-+ 0);
-+ } else if (dev->bus_master->bitbang_pullup) {
-+ dev->bus_master->
-+ bitbang_pullup(dev->bus_master->data, 1);
- msleep(dev->pullup_duration);
-+ dev->bus_master->
-+ bitbang_pullup(dev->bus_master->data, 0);
-+ }
-+ } else {
-+ msleep(dev->pullup_duration);
-+ }
-+
- dev->pullup_duration = 0;
- }
- }
---- a/include/linux/w1-gpio.h
-+++ b/include/linux/w1-gpio.h
-@@ -18,6 +18,7 @@
- struct w1_gpio_platform_data {
- unsigned int pin;
- unsigned int is_open_drain:1;
-+ unsigned int parasitic_power:1;
- void (*enable_external_pullup)(int enable);
- unsigned int ext_pullup_enable_pin;
- unsigned int pullup_duration;
diff --git a/target/linux/brcm2708/patches-4.4/0060-Added-Device-IDs-for-August-DVB-T-205.patch b/target/linux/brcm2708/patches-4.4/0060-Added-Device-IDs-for-August-DVB-T-205.patch
deleted file mode 100644
index 1f97fbb..0000000
--- a/target/linux/brcm2708/patches-4.4/0060-Added-Device-IDs-for-August-DVB-T-205.patch
+++ /dev/null
@@ -1,22 +0,0 @@
-From b0e3030168c6f3a286e10ac36b231d10268799ad Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Wed, 3 Jul 2013 00:54:08 +0100
-Subject: [PATCH] Added Device IDs for August DVB-T 205
-
----
- drivers/media/usb/dvb-usb-v2/rtl28xxu.c | 4 ++++
- 1 file changed, 4 insertions(+)
-
---- a/drivers/media/usb/dvb-usb-v2/rtl28xxu.c
-+++ b/drivers/media/usb/dvb-usb-v2/rtl28xxu.c
-@@ -1900,6 +1900,10 @@ static const struct usb_device_id rtl28x
- &rtl28xxu_props, "Compro VideoMate U650F", NULL) },
- { DVB_USB_DEVICE(USB_VID_KWORLD_2, 0xd394,
- &rtl28xxu_props, "MaxMedia HU394-T", NULL) },
-+ { DVB_USB_DEVICE(USB_VID_GTEK, 0xb803 /*USB_PID_AUGUST_DVBT205*/,
-+ &rtl28xxu_props, "August DVB-T 205", NULL) },
-+ { DVB_USB_DEVICE(USB_VID_GTEK, 0xa803 /*USB_PID_AUGUST_DVBT205*/,
-+ &rtl28xxu_props, "August DVB-T 205", NULL) },
- { DVB_USB_DEVICE(USB_VID_LEADTEK, 0x6a03,
- &rtl28xxu_props, "Leadtek WinFast DTV Dongle mini", NULL) },
- { DVB_USB_DEVICE(USB_VID_GTEK, USB_PID_CPYTO_REDI_PC50A,
diff --git a/target/linux/brcm2708/patches-4.4/0061-config-Enable-CONFIG_MEMCG-but-leave-it-disabled-due.patch b/target/linux/brcm2708/patches-4.4/0061-config-Enable-CONFIG_MEMCG-but-leave-it-disabled-due.patch
deleted file mode 100644
index 22b3616..0000000
--- a/target/linux/brcm2708/patches-4.4/0061-config-Enable-CONFIG_MEMCG-but-leave-it-disabled-due.patch
+++ /dev/null
@@ -1,49 +0,0 @@
-From 39fe92f88d44056587caa272d450dd5a6ecb9a4e Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Wed, 18 Dec 2013 22:16:19 +0000
-Subject: [PATCH] config: Enable CONFIG_MEMCG, but leave it disabled (due to
- memory cost). Enable with cgroup_enable=memory.
-
----
- kernel/cgroup.c | 23 ++++++++++++++++++++++-
- 1 file changed, 22 insertions(+), 1 deletion(-)
-
---- a/kernel/cgroup.c
-+++ b/kernel/cgroup.c
-@@ -5310,7 +5310,7 @@ int __init cgroup_init_early(void)
- return 0;
- }
-
--static unsigned long cgroup_disable_mask __initdata;
-+static unsigned long cgroup_disable_mask __initdata = 1<<0;
-
- /**
- * cgroup_init - cgroup initialization
-@@ -5806,6 +5806,27 @@ static int __init cgroup_disable(char *s
- }
- __setup("cgroup_disable=", cgroup_disable);
-
-+static int __init cgroup_enable(char *str)
-+{
-+ struct cgroup_subsys *ss;
-+ char *token;
-+ int i;
-+
-+ while ((token = strsep(&str, ",")) != NULL) {
-+ if (!*token)
-+ continue;
-+
-+ for_each_subsys(ss, i) {
-+ if (strcmp(token, ss->name) &&
-+ strcmp(token, ss->legacy_name))
-+ continue;
-+ cgroup_disable_mask &= ~(1 << i);
-+ }
-+ }
-+ return 1;
-+}
-+__setup("cgroup_enable=", cgroup_enable);
-+
- /**
- * css_tryget_online_from_dir - get corresponding css from a cgroup dentry
- * @dentry: directory dentry of interest
diff --git a/target/linux/brcm2708/patches-4.4/0062-ASoC-Add-support-for-PCM5102A-codec.patch b/target/linux/brcm2708/patches-4.4/0062-ASoC-Add-support-for-PCM5102A-codec.patch
deleted file mode 100644
index d2d5cf6..0000000
--- a/target/linux/brcm2708/patches-4.4/0062-ASoC-Add-support-for-PCM5102A-codec.patch
+++ /dev/null
@@ -1,128 +0,0 @@
-From f3e09b361bf5b1d8174f9b0631ab586ce9214496 Mon Sep 17 00:00:00 2001
-From: Florian Meier <florian.meier at koalo.de>
-Date: Fri, 22 Nov 2013 14:59:51 +0100
-Subject: [PATCH] ASoC: Add support for PCM5102A codec
-
-Some definitions to support the PCM5102A codec
-by Texas Instruments.
-
-Signed-off-by: Florian Meier <florian.meier at koalo.de>
----
- sound/soc/codecs/Kconfig | 5 ++++
- sound/soc/codecs/Makefile | 2 ++
- sound/soc/codecs/pcm5102a.c | 70 +++++++++++++++++++++++++++++++++++++++++++++
- 3 files changed, 77 insertions(+)
- create mode 100644 sound/soc/codecs/pcm5102a.c
-
---- a/sound/soc/codecs/Kconfig
-+++ b/sound/soc/codecs/Kconfig
-@@ -89,6 +89,7 @@ config SND_SOC_ALL_CODECS
- select SND_SOC_PCM512x_SPI if SPI_MASTER
- select SND_SOC_RT286 if I2C
- select SND_SOC_RT298 if I2C
-+ select SND_SOC_PCM5102A if I2C
- select SND_SOC_RT5631 if I2C
- select SND_SOC_RT5640 if I2C
- select SND_SOC_RT5645 if I2C
-@@ -549,6 +550,10 @@ config SND_SOC_RT298
- tristate
- depends on I2C
-
-+config SND_SOC_PCM5102A
-+ tristate
-+ depends on I2C
-+
- config SND_SOC_RT5631
- tristate "Realtek ALC5631/RT5631 CODEC"
- depends on I2C
---- a/sound/soc/codecs/Makefile
-+++ b/sound/soc/codecs/Makefile
-@@ -85,6 +85,7 @@ snd-soc-rl6231-objs := rl6231.o
- snd-soc-rl6347a-objs := rl6347a.o
- snd-soc-rt286-objs := rt286.o
- snd-soc-rt298-objs := rt298.o
-+snd-soc-pcm5102a-objs := pcm5102a.o
- snd-soc-rt5631-objs := rt5631.o
- snd-soc-rt5640-objs := rt5640.o
- snd-soc-rt5645-objs := rt5645.o
-@@ -280,6 +281,7 @@ obj-$(CONFIG_SND_SOC_RL6231) += snd-soc-
- obj-$(CONFIG_SND_SOC_RL6347A) += snd-soc-rl6347a.o
- obj-$(CONFIG_SND_SOC_RT286) += snd-soc-rt286.o
- obj-$(CONFIG_SND_SOC_RT298) += snd-soc-rt298.o
-+obj-$(CONFIG_SND_SOC_PCM5102A) += snd-soc-pcm5102a.o
- obj-$(CONFIG_SND_SOC_RT5631) += snd-soc-rt5631.o
- obj-$(CONFIG_SND_SOC_RT5640) += snd-soc-rt5640.o
- obj-$(CONFIG_SND_SOC_RT5645) += snd-soc-rt5645.o
---- /dev/null
-+++ b/sound/soc/codecs/pcm5102a.c
-@@ -0,0 +1,70 @@
-+/*
-+ * Driver for the PCM5102A codec
-+ *
-+ * Author: Florian Meier <florian.meier at koalo.de>
-+ * Copyright 2013
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * version 2 as published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful, but
-+ * WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
-+ * General Public License for more details.
-+ */
-+
-+
-+#include <linux/init.h>
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+
-+#include <sound/soc.h>
-+
-+static struct snd_soc_dai_driver pcm5102a_dai = {
-+ .name = "pcm5102a-hifi",
-+ .playback = {
-+ .channels_min = 2,
-+ .channels_max = 2,
-+ .rates = SNDRV_PCM_RATE_8000_192000,
-+ .formats = SNDRV_PCM_FMTBIT_S16_LE |
-+ SNDRV_PCM_FMTBIT_S24_LE |
-+ SNDRV_PCM_FMTBIT_S32_LE
-+ },
-+};
-+
-+static struct snd_soc_codec_driver soc_codec_dev_pcm5102a;
-+
-+static int pcm5102a_probe(struct platform_device *pdev)
-+{
-+ return snd_soc_register_codec(&pdev->dev, &soc_codec_dev_pcm5102a,
-+ &pcm5102a_dai, 1);
-+}
-+
-+static int pcm5102a_remove(struct platform_device *pdev)
-+{
-+ snd_soc_unregister_codec(&pdev->dev);
-+ return 0;
-+}
-+
-+static const struct of_device_id pcm5102a_of_match[] = {
-+ { .compatible = "ti,pcm5102a", },
-+ { }
-+};
-+MODULE_DEVICE_TABLE(of, pcm5102a_of_match);
-+
-+static struct platform_driver pcm5102a_codec_driver = {
-+ .probe = pcm5102a_probe,
-+ .remove = pcm5102a_remove,
-+ .driver = {
-+ .name = "pcm5102a-codec",
-+ .owner = THIS_MODULE,
-+ .of_match_table = pcm5102a_of_match,
-+ },
-+};
-+
-+module_platform_driver(pcm5102a_codec_driver);
-+
-+MODULE_DESCRIPTION("ASoC PCM5102A codec driver");
-+MODULE_AUTHOR("Florian Meier <florian.meier at koalo.de>");
-+MODULE_LICENSE("GPL v2");
diff --git a/target/linux/brcm2708/patches-4.4/0063-ASoC-Add-support-for-HifiBerry-DAC.patch b/target/linux/brcm2708/patches-4.4/0063-ASoC-Add-support-for-HifiBerry-DAC.patch
deleted file mode 100644
index 98f1d95..0000000
--- a/target/linux/brcm2708/patches-4.4/0063-ASoC-Add-support-for-HifiBerry-DAC.patch
+++ /dev/null
@@ -1,165 +0,0 @@
-From 8d203b91f4f8f8d582eb5c382357fe1e6d1d96d1 Mon Sep 17 00:00:00 2001
-From: Florian Meier <florian.meier at koalo.de>
-Date: Fri, 22 Nov 2013 19:19:08 +0100
-Subject: [PATCH] ASoC: Add support for HifiBerry DAC
-
-This adds a machine driver for the HifiBerry DAC.
-It is a sound card that can
-be stacked onto the Raspberry Pi.
-
-Signed-off-by: Florian Meier <florian.meier at koalo.de>
----
- sound/soc/bcm/Kconfig | 7 +++
- sound/soc/bcm/Makefile | 4 ++
- sound/soc/bcm/hifiberry_dac.c | 122 ++++++++++++++++++++++++++++++++++++++++++
- 3 files changed, 133 insertions(+)
- create mode 100644 sound/soc/bcm/hifiberry_dac.c
-
---- a/sound/soc/bcm/Kconfig
-+++ b/sound/soc/bcm/Kconfig
-@@ -7,3 +7,10 @@ config SND_BCM2835_SOC_I2S
- Say Y or M if you want to add support for codecs attached to
- the BCM2835 I2S interface. You will also need
- to select the audio interfaces to support below.
-+
-+config SND_BCM2708_SOC_HIFIBERRY_DAC
-+ tristate "Support for HifiBerry DAC"
-+ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
-+ select SND_SOC_PCM5102A
-+ help
-+ Say Y or M if you want to add support for HifiBerry DAC.
---- a/sound/soc/bcm/Makefile
-+++ b/sound/soc/bcm/Makefile
-@@ -3,3 +3,7 @@ snd-soc-bcm2835-i2s-objs := bcm2835-i2s.
-
- obj-$(CONFIG_SND_BCM2835_SOC_I2S) += snd-soc-bcm2835-i2s.o
-
-+# BCM2708 Machine Support
-+snd-soc-hifiberry-dac-objs := hifiberry_dac.o
-+
-+obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DAC) += snd-soc-hifiberry-dac.o
---- /dev/null
-+++ b/sound/soc/bcm/hifiberry_dac.c
-@@ -0,0 +1,122 @@
-+/*
-+ * ASoC Driver for HifiBerry DAC
-+ *
-+ * Author: Florian Meier <florian.meier at koalo.de>
-+ * Copyright 2013
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * version 2 as published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful, but
-+ * WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
-+ * General Public License for more details.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+
-+#include <sound/core.h>
-+#include <sound/pcm.h>
-+#include <sound/pcm_params.h>
-+#include <sound/soc.h>
-+#include <sound/jack.h>
-+
-+static int snd_rpi_hifiberry_dac_init(struct snd_soc_pcm_runtime *rtd)
-+{
-+ return 0;
-+}
-+
-+static int snd_rpi_hifiberry_dac_hw_params(struct snd_pcm_substream *substream,
-+ struct snd_pcm_hw_params *params)
-+{
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
-+
-+ unsigned int sample_bits =
-+ snd_pcm_format_physical_width(params_format(params));
-+
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, sample_bits * 2);
-+}
-+
-+/* machine stream operations */
-+static struct snd_soc_ops snd_rpi_hifiberry_dac_ops = {
-+ .hw_params = snd_rpi_hifiberry_dac_hw_params,
-+};
-+
-+static struct snd_soc_dai_link snd_rpi_hifiberry_dac_dai[] = {
-+{
-+ .name = "HifiBerry DAC",
-+ .stream_name = "HifiBerry DAC HiFi",
-+ .cpu_dai_name = "bcm2708-i2s.0",
-+ .codec_dai_name = "pcm5102a-hifi",
-+ .platform_name = "bcm2708-i2s.0",
-+ .codec_name = "pcm5102a-codec",
-+ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF |
-+ SND_SOC_DAIFMT_CBS_CFS,
-+ .ops = &snd_rpi_hifiberry_dac_ops,
-+ .init = snd_rpi_hifiberry_dac_init,
-+},
-+};
-+
-+/* audio machine driver */
-+static struct snd_soc_card snd_rpi_hifiberry_dac = {
-+ .name = "snd_rpi_hifiberry_dac",
-+ .dai_link = snd_rpi_hifiberry_dac_dai,
-+ .num_links = ARRAY_SIZE(snd_rpi_hifiberry_dac_dai),
-+};
-+
-+static int snd_rpi_hifiberry_dac_probe(struct platform_device *pdev)
-+{
-+ int ret = 0;
-+
-+ snd_rpi_hifiberry_dac.dev = &pdev->dev;
-+
-+ if (pdev->dev.of_node) {
-+ struct device_node *i2s_node;
-+ struct snd_soc_dai_link *dai = &snd_rpi_hifiberry_dac_dai[0];
-+ i2s_node = of_parse_phandle(pdev->dev.of_node,
-+ "i2s-controller", 0);
-+
-+ if (i2s_node) {
-+ dai->cpu_dai_name = NULL;
-+ dai->cpu_of_node = i2s_node;
-+ dai->platform_name = NULL;
-+ dai->platform_of_node = i2s_node;
-+ }
-+ }
-+
-+ ret = snd_soc_register_card(&snd_rpi_hifiberry_dac);
-+ if (ret)
-+ dev_err(&pdev->dev, "snd_soc_register_card() failed: %d\n", ret);
-+
-+ return ret;
-+}
-+
-+static int snd_rpi_hifiberry_dac_remove(struct platform_device *pdev)
-+{
-+ return snd_soc_unregister_card(&snd_rpi_hifiberry_dac);
-+}
-+
-+static const struct of_device_id snd_rpi_hifiberry_dac_of_match[] = {
-+ { .compatible = "hifiberry,hifiberry-dac", },
-+ {},
-+};
-+MODULE_DEVICE_TABLE(of, snd_rpi_hifiberry_dac_of_match);
-+
-+static struct platform_driver snd_rpi_hifiberry_dac_driver = {
-+ .driver = {
-+ .name = "snd-hifiberry-dac",
-+ .owner = THIS_MODULE,
-+ .of_match_table = snd_rpi_hifiberry_dac_of_match,
-+ },
-+ .probe = snd_rpi_hifiberry_dac_probe,
-+ .remove = snd_rpi_hifiberry_dac_remove,
-+};
-+
-+module_platform_driver(snd_rpi_hifiberry_dac_driver);
-+
-+MODULE_AUTHOR("Florian Meier <florian.meier at koalo.de>");
-+MODULE_DESCRIPTION("ASoC Driver for HifiBerry DAC");
-+MODULE_LICENSE("GPL v2");
diff --git a/target/linux/brcm2708/patches-4.4/0064-ASoC-Add-support-for-Rpi-DAC.patch b/target/linux/brcm2708/patches-4.4/0064-ASoC-Add-support-for-Rpi-DAC.patch
deleted file mode 100644
index 44636fe..0000000
--- a/target/linux/brcm2708/patches-4.4/0064-ASoC-Add-support-for-Rpi-DAC.patch
+++ /dev/null
@@ -1,275 +0,0 @@
-From d508e0f3ad2d918c85bd034f5da216c9498a3d6a Mon Sep 17 00:00:00 2001
-From: Florian Meier <florian.meier at koalo.de>
-Date: Fri, 22 Nov 2013 19:21:34 +0100
-Subject: [PATCH] ASoC: Add support for Rpi-DAC
-
----
- sound/soc/bcm/Kconfig | 7 +++
- sound/soc/bcm/Makefile | 2 +
- sound/soc/bcm/rpi-dac.c | 118 ++++++++++++++++++++++++++++++++++++++++++++
- sound/soc/codecs/Kconfig | 9 ++++
- sound/soc/codecs/Makefile | 2 +
- sound/soc/codecs/pcm1794a.c | 69 ++++++++++++++++++++++++++
- 6 files changed, 207 insertions(+)
- create mode 100644 sound/soc/bcm/rpi-dac.c
- create mode 100644 sound/soc/codecs/pcm1794a.c
-
---- a/sound/soc/bcm/Kconfig
-+++ b/sound/soc/bcm/Kconfig
-@@ -14,3 +14,10 @@ config SND_BCM2708_SOC_HIFIBERRY_DAC
- select SND_SOC_PCM5102A
- help
- Say Y or M if you want to add support for HifiBerry DAC.
-+
-+config SND_BCM2708_SOC_RPI_DAC
-+ tristate "Support for RPi-DAC"
-+ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
-+ select SND_SOC_PCM1794A
-+ help
-+ Say Y or M if you want to add support for RPi-DAC.
---- a/sound/soc/bcm/Makefile
-+++ b/sound/soc/bcm/Makefile
-@@ -5,5 +5,7 @@ obj-$(CONFIG_SND_BCM2835_SOC_I2S) += snd
-
- # BCM2708 Machine Support
- snd-soc-hifiberry-dac-objs := hifiberry_dac.o
-+snd-soc-rpi-dac-objs := rpi-dac.o
-
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DAC) += snd-soc-hifiberry-dac.o
-+obj-$(CONFIG_SND_BCM2708_SOC_RPI_DAC) += snd-soc-rpi-dac.o
---- /dev/null
-+++ b/sound/soc/bcm/rpi-dac.c
-@@ -0,0 +1,118 @@
-+/*
-+ * ASoC Driver for RPi-DAC.
-+ *
-+ * Author: Florian Meier <florian.meier at koalo.de>
-+ * Copyright 2013
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * version 2 as published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful, but
-+ * WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
-+ * General Public License for more details.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+
-+#include <sound/core.h>
-+#include <sound/pcm.h>
-+#include <sound/pcm_params.h>
-+#include <sound/soc.h>
-+#include <sound/jack.h>
-+
-+static int snd_rpi_rpi_dac_init(struct snd_soc_pcm_runtime *rtd)
-+{
-+ return 0;
-+}
-+
-+static int snd_rpi_rpi_dac_hw_params(struct snd_pcm_substream *substream,
-+ struct snd_pcm_hw_params *params)
-+{
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
-+
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, 32*2);
-+}
-+
-+/* machine stream operations */
-+static struct snd_soc_ops snd_rpi_rpi_dac_ops = {
-+ .hw_params = snd_rpi_rpi_dac_hw_params,
-+};
-+
-+static struct snd_soc_dai_link snd_rpi_rpi_dac_dai[] = {
-+{
-+ .name = "RPi-DAC",
-+ .stream_name = "RPi-DAC HiFi",
-+ .cpu_dai_name = "bcm2708-i2s.0",
-+ .codec_dai_name = "pcm1794a-hifi",
-+ .platform_name = "bcm2708-i2s.0",
-+ .codec_name = "pcm1794a-codec",
-+ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF |
-+ SND_SOC_DAIFMT_CBS_CFS,
-+ .ops = &snd_rpi_rpi_dac_ops,
-+ .init = snd_rpi_rpi_dac_init,
-+},
-+};
-+
-+/* audio machine driver */
-+static struct snd_soc_card snd_rpi_rpi_dac = {
-+ .name = "snd_rpi_rpi_dac",
-+ .dai_link = snd_rpi_rpi_dac_dai,
-+ .num_links = ARRAY_SIZE(snd_rpi_rpi_dac_dai),
-+};
-+
-+static int snd_rpi_rpi_dac_probe(struct platform_device *pdev)
-+{
-+ int ret = 0;
-+
-+ snd_rpi_rpi_dac.dev = &pdev->dev;
-+
-+ if (pdev->dev.of_node) {
-+ struct device_node *i2s_node;
-+ struct snd_soc_dai_link *dai = &snd_rpi_rpi_dac_dai[0];
-+ i2s_node = of_parse_phandle(pdev->dev.of_node, "i2s-controller", 0);
-+
-+ if (i2s_node) {
-+ dai->cpu_dai_name = NULL;
-+ dai->cpu_of_node = i2s_node;
-+ dai->platform_name = NULL;
-+ dai->platform_of_node = i2s_node;
-+ }
-+ }
-+
-+ ret = snd_soc_register_card(&snd_rpi_rpi_dac);
-+ if (ret)
-+ dev_err(&pdev->dev, "snd_soc_register_card() failed: %d\n", ret);
-+
-+ return ret;
-+}
-+
-+static int snd_rpi_rpi_dac_remove(struct platform_device *pdev)
-+{
-+ return snd_soc_unregister_card(&snd_rpi_rpi_dac);
-+}
-+
-+static const struct of_device_id snd_rpi_rpi_dac_of_match[] = {
-+ { .compatible = "rpi,rpi-dac", },
-+ {},
-+};
-+MODULE_DEVICE_TABLE(of, snd_rpi_rpi_dac_of_match);
-+
-+static struct platform_driver snd_rpi_rpi_dac_driver = {
-+ .driver = {
-+ .name = "snd-rpi-dac",
-+ .owner = THIS_MODULE,
-+ .of_match_table = snd_rpi_rpi_dac_of_match,
-+ },
-+ .probe = snd_rpi_rpi_dac_probe,
-+ .remove = snd_rpi_rpi_dac_remove,
-+};
-+
-+module_platform_driver(snd_rpi_rpi_dac_driver);
-+
-+MODULE_AUTHOR("Florian Meier <florian.meier at koalo.de>");
-+MODULE_DESCRIPTION("ASoC Driver for RPi-DAC");
-+MODULE_LICENSE("GPL v2");
---- a/sound/soc/codecs/Kconfig
-+++ b/sound/soc/codecs/Kconfig
-@@ -90,6 +90,7 @@ config SND_SOC_ALL_CODECS
- select SND_SOC_RT286 if I2C
- select SND_SOC_RT298 if I2C
- select SND_SOC_PCM5102A if I2C
-+ select SND_SOC_PCM1794A if I2C
- select SND_SOC_RT5631 if I2C
- select SND_SOC_RT5640 if I2C
- select SND_SOC_RT5645 if I2C
-@@ -550,6 +551,14 @@ config SND_SOC_RT298
- tristate
- depends on I2C
-
-+config SND_SOC_RT298
-+ tristate
-+ depends on I2C
-+
-+config SND_SOC_PCM1794A
-+ tristate
-+ depends on I2C
-+
- config SND_SOC_PCM5102A
- tristate
- depends on I2C
---- a/sound/soc/codecs/Makefile
-+++ b/sound/soc/codecs/Makefile
-@@ -85,6 +85,7 @@ snd-soc-rl6231-objs := rl6231.o
- snd-soc-rl6347a-objs := rl6347a.o
- snd-soc-rt286-objs := rt286.o
- snd-soc-rt298-objs := rt298.o
-+snd-soc-pcm1794a-objs := pcm1794a.o
- snd-soc-pcm5102a-objs := pcm5102a.o
- snd-soc-rt5631-objs := rt5631.o
- snd-soc-rt5640-objs := rt5640.o
-@@ -281,6 +282,7 @@ obj-$(CONFIG_SND_SOC_RL6231) += snd-soc-
- obj-$(CONFIG_SND_SOC_RL6347A) += snd-soc-rl6347a.o
- obj-$(CONFIG_SND_SOC_RT286) += snd-soc-rt286.o
- obj-$(CONFIG_SND_SOC_RT298) += snd-soc-rt298.o
-+obj-$(CONFIG_SND_SOC_PCM1794A) += snd-soc-pcm1794a.o
- obj-$(CONFIG_SND_SOC_PCM5102A) += snd-soc-pcm5102a.o
- obj-$(CONFIG_SND_SOC_RT5631) += snd-soc-rt5631.o
- obj-$(CONFIG_SND_SOC_RT5640) += snd-soc-rt5640.o
---- /dev/null
-+++ b/sound/soc/codecs/pcm1794a.c
-@@ -0,0 +1,69 @@
-+/*
-+ * Driver for the PCM1794A codec
-+ *
-+ * Author: Florian Meier <florian.meier at koalo.de>
-+ * Copyright 2013
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * version 2 as published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful, but
-+ * WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
-+ * General Public License for more details.
-+ */
-+
-+
-+#include <linux/init.h>
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+
-+#include <sound/soc.h>
-+
-+static struct snd_soc_dai_driver pcm1794a_dai = {
-+ .name = "pcm1794a-hifi",
-+ .playback = {
-+ .channels_min = 2,
-+ .channels_max = 2,
-+ .rates = SNDRV_PCM_RATE_8000_192000,
-+ .formats = SNDRV_PCM_FMTBIT_S16_LE |
-+ SNDRV_PCM_FMTBIT_S24_LE
-+ },
-+};
-+
-+static struct snd_soc_codec_driver soc_codec_dev_pcm1794a;
-+
-+static int pcm1794a_probe(struct platform_device *pdev)
-+{
-+ return snd_soc_register_codec(&pdev->dev, &soc_codec_dev_pcm1794a,
-+ &pcm1794a_dai, 1);
-+}
-+
-+static int pcm1794a_remove(struct platform_device *pdev)
-+{
-+ snd_soc_unregister_codec(&pdev->dev);
-+ return 0;
-+}
-+
-+static const struct of_device_id pcm1794a_of_match[] = {
-+ { .compatible = "ti,pcm1794a", },
-+ { }
-+};
-+MODULE_DEVICE_TABLE(of, pcm1794a_of_match);
-+
-+static struct platform_driver pcm1794a_codec_driver = {
-+ .probe = pcm1794a_probe,
-+ .remove = pcm1794a_remove,
-+ .driver = {
-+ .name = "pcm1794a-codec",
-+ .owner = THIS_MODULE,
-+ .of_match_table = of_match_ptr(pcm1794a_of_match),
-+ },
-+};
-+
-+module_platform_driver(pcm1794a_codec_driver);
-+
-+MODULE_DESCRIPTION("ASoC PCM1794A codec driver");
-+MODULE_AUTHOR("Florian Meier <florian.meier at koalo.de>");
-+MODULE_LICENSE("GPL v2");
diff --git a/target/linux/brcm2708/patches-4.4/0065-ASoC-wm8804-Implement-MCLK-configuration-options-add.patch b/target/linux/brcm2708/patches-4.4/0065-ASoC-wm8804-Implement-MCLK-configuration-options-add.patch
deleted file mode 100644
index ebbc6c0..0000000
--- a/target/linux/brcm2708/patches-4.4/0065-ASoC-wm8804-Implement-MCLK-configuration-options-add.patch
+++ /dev/null
@@ -1,40 +0,0 @@
-From bc573ada196b56eea95c1cca6520b916ec06660a Mon Sep 17 00:00:00 2001
-From: Daniel Matuschek <info at crazy-audio.com>
-Date: Wed, 15 Jan 2014 21:41:23 +0100
-Subject: [PATCH] ASoC: wm8804: Implement MCLK configuration options, add 32bit
- support WM8804 can run with PLL frequencies of 256xfs and 128xfs for most
- sample rates. At 192kHz only 128xfs is supported. The existing driver selects
- 128xfs automatically for some lower samples rates. By using an additional
- mclk_div divider, it is now possible to control the behaviour. This allows
- using 256xfs PLL frequency on all sample rates up to 96kHz. It should allow
- lower jitter and better signal quality. The behavior has to be controlled by
- the sound card driver, because some sample frequency share the same setting.
- e.g. 192kHz and 96kHz use 24.576MHz master clock. The only difference is the
- MCLK divider.
-
-This also added support for 32bit data.
-
-Signed-off-by: Daniel Matuschek <daniel at matuschek.net>
----
- sound/soc/codecs/wm8804.c | 3 ++-
- 1 file changed, 2 insertions(+), 1 deletion(-)
-
---- a/sound/soc/codecs/wm8804.c
-+++ b/sound/soc/codecs/wm8804.c
-@@ -304,6 +304,7 @@ static int wm8804_hw_params(struct snd_p
- blen = 0x1;
- break;
- case 24:
-+ case 32:
- blen = 0x2;
- break;
- default:
-@@ -515,7 +516,7 @@ static const struct snd_soc_dai_ops wm88
- };
-
- #define WM8804_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S20_3LE | \
-- SNDRV_PCM_FMTBIT_S24_LE)
-+ SNDRV_PCM_FMTBIT_S24_3LE | SNDRV_PCM_FMTBIT_S32_LE)
-
- #define WM8804_RATES (SNDRV_PCM_RATE_32000 | SNDRV_PCM_RATE_44100 | \
- SNDRV_PCM_RATE_48000 | SNDRV_PCM_RATE_64000 | \
diff --git a/target/linux/brcm2708/patches-4.4/0066-ASoC-BCM-Add-support-for-HiFiBerry-Digi.-Driver-is-b.patch b/target/linux/brcm2708/patches-4.4/0066-ASoC-BCM-Add-support-for-HiFiBerry-Digi.-Driver-is-b.patch
deleted file mode 100644
index d037440..0000000
--- a/target/linux/brcm2708/patches-4.4/0066-ASoC-BCM-Add-support-for-HiFiBerry-Digi.-Driver-is-b.patch
+++ /dev/null
@@ -1,282 +0,0 @@
-From eeb5b47b928a485cfe3b10bd983786aaf2050ca8 Mon Sep 17 00:00:00 2001
-From: Daniel Matuschek <info at crazy-audio.com>
-Date: Wed, 15 Jan 2014 21:42:08 +0100
-Subject: [PATCH] ASoC: BCM:Add support for HiFiBerry Digi. Driver is based on
- the patched WM8804 driver.
-
-Signed-off-by: Daniel Matuschek <daniel at matuschek.net>
-
-Add a parameter to turn off SPDIF output if no audio is playing
-
-This patch adds the paramater auto_shutdown_output to the kernel module.
-Default behaviour of the module is the same, but when auto_shutdown_output
-is set to 1, the SPDIF oputput will shutdown if no stream is playing.
-
-bugfix for 32kHz sample rate, was missing
-
-HiFiBerry Digi: set SPDIF status bits for sample rate
-
-The HiFiBerry Digi driver did not signal the sample rate in the SPDIF status bits.
-While this is optional, some DACs and receivers do not accept this signal. This patch
-adds the sample rate bits in the SPDIF status block.
----
- sound/soc/bcm/Kconfig | 7 ++
- sound/soc/bcm/Makefile | 2 +
- sound/soc/bcm/hifiberry_digi.c | 223 +++++++++++++++++++++++++++++++++++++++++
- 3 files changed, 232 insertions(+)
- create mode 100644 sound/soc/bcm/hifiberry_digi.c
-
---- a/sound/soc/bcm/Kconfig
-+++ b/sound/soc/bcm/Kconfig
-@@ -15,6 +15,13 @@ config SND_BCM2708_SOC_HIFIBERRY_DAC
- help
- Say Y or M if you want to add support for HifiBerry DAC.
-
-+config SND_BCM2708_SOC_HIFIBERRY_DIGI
-+ tristate "Support for HifiBerry Digi"
-+ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
-+ select SND_SOC_WM8804
-+ help
-+ Say Y or M if you want to add support for HifiBerry Digi S/PDIF output board.
-+
- config SND_BCM2708_SOC_RPI_DAC
- tristate "Support for RPi-DAC"
- depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
---- a/sound/soc/bcm/Makefile
-+++ b/sound/soc/bcm/Makefile
-@@ -5,7 +5,9 @@ obj-$(CONFIG_SND_BCM2835_SOC_I2S) += snd
-
- # BCM2708 Machine Support
- snd-soc-hifiberry-dac-objs := hifiberry_dac.o
-+snd-soc-hifiberry-digi-objs := hifiberry_digi.o
- snd-soc-rpi-dac-objs := rpi-dac.o
-
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DAC) += snd-soc-hifiberry-dac.o
-+obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DIGI) += snd-soc-hifiberry-digi.o
- obj-$(CONFIG_SND_BCM2708_SOC_RPI_DAC) += snd-soc-rpi-dac.o
---- /dev/null
-+++ b/sound/soc/bcm/hifiberry_digi.c
-@@ -0,0 +1,223 @@
-+/*
-+ * ASoC Driver for HifiBerry Digi
-+ *
-+ * Author: Daniel Matuschek <info at crazy-audio.com>
-+ * based on the HifiBerry DAC driver by Florian Meier <florian.meier at koalo.de>
-+ * Copyright 2013
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * version 2 as published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful, but
-+ * WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
-+ * General Public License for more details.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+
-+#include <sound/core.h>
-+#include <sound/pcm.h>
-+#include <sound/pcm_params.h>
-+#include <sound/soc.h>
-+#include <sound/jack.h>
-+
-+#include "../codecs/wm8804.h"
-+
-+static short int auto_shutdown_output = 0;
-+module_param(auto_shutdown_output, short, S_IRUSR | S_IWUSR | S_IRGRP | S_IWGRP);
-+MODULE_PARM_DESC(auto_shutdown_output, "Shutdown SP/DIF output if playback is stopped");
-+
-+
-+static int samplerate=44100;
-+
-+static int snd_rpi_hifiberry_digi_init(struct snd_soc_pcm_runtime *rtd)
-+{
-+ struct snd_soc_codec *codec = rtd->codec;
-+
-+ /* enable TX output */
-+ snd_soc_update_bits(codec, WM8804_PWRDN, 0x4, 0x0);
-+
-+ return 0;
-+}
-+
-+static int snd_rpi_hifiberry_digi_startup(struct snd_pcm_substream *substream) {
-+ /* turn on digital output */
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_codec *codec = rtd->codec;
-+ snd_soc_update_bits(codec, WM8804_PWRDN, 0x3c, 0x00);
-+ return 0;
-+}
-+
-+static void snd_rpi_hifiberry_digi_shutdown(struct snd_pcm_substream *substream) {
-+ /* turn off output */
-+ if (auto_shutdown_output) {
-+ /* turn off output */
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_codec *codec = rtd->codec;
-+ snd_soc_update_bits(codec, WM8804_PWRDN, 0x3c, 0x3c);
-+ }
-+}
-+
-+
-+static int snd_rpi_hifiberry_digi_hw_params(struct snd_pcm_substream *substream,
-+ struct snd_pcm_hw_params *params)
-+{
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_dai *codec_dai = rtd->codec_dai;
-+ struct snd_soc_codec *codec = rtd->codec;
-+ struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
-+
-+ int sysclk = 27000000; /* This is fixed on this board */
-+
-+ long mclk_freq=0;
-+ int mclk_div=1;
-+ int sampling_freq=1;
-+
-+ int ret;
-+
-+ samplerate = params_rate(params);
-+
-+ if (samplerate<=96000) {
-+ mclk_freq=samplerate*256;
-+ mclk_div=WM8804_MCLKDIV_256FS;
-+ } else {
-+ mclk_freq=samplerate*128;
-+ mclk_div=WM8804_MCLKDIV_128FS;
-+ }
-+
-+ switch (samplerate) {
-+ case 32000:
-+ sampling_freq=0x03;
-+ break;
-+ case 44100:
-+ sampling_freq=0x00;
-+ break;
-+ case 48000:
-+ sampling_freq=0x02;
-+ break;
-+ case 88200:
-+ sampling_freq=0x08;
-+ break;
-+ case 96000:
-+ sampling_freq=0x0a;
-+ break;
-+ case 176400:
-+ sampling_freq=0x0c;
-+ break;
-+ case 192000:
-+ sampling_freq=0x0e;
-+ break;
-+ default:
-+ dev_err(codec->dev,
-+ "Failed to set WM8804 SYSCLK, unsupported samplerate %d\n",
-+ samplerate);
-+ }
-+
-+ snd_soc_dai_set_clkdiv(codec_dai, WM8804_MCLK_DIV, mclk_div);
-+ snd_soc_dai_set_pll(codec_dai, 0, 0, sysclk, mclk_freq);
-+
-+ ret = snd_soc_dai_set_sysclk(codec_dai, WM8804_TX_CLKSRC_PLL,
-+ sysclk, SND_SOC_CLOCK_OUT);
-+ if (ret < 0) {
-+ dev_err(codec->dev,
-+ "Failed to set WM8804 SYSCLK: %d\n", ret);
-+ return ret;
-+ }
-+
-+ /* Enable TX output */
-+ snd_soc_update_bits(codec, WM8804_PWRDN, 0x4, 0x0);
-+
-+ /* Power on */
-+ snd_soc_update_bits(codec, WM8804_PWRDN, 0x9, 0);
-+
-+ /* set sampling frequency status bits */
-+ snd_soc_update_bits(codec, WM8804_SPDTX4, 0x0f, sampling_freq);
-+
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai,64);
-+}
-+
-+/* machine stream operations */
-+static struct snd_soc_ops snd_rpi_hifiberry_digi_ops = {
-+ .hw_params = snd_rpi_hifiberry_digi_hw_params,
-+ .startup = snd_rpi_hifiberry_digi_startup,
-+ .shutdown = snd_rpi_hifiberry_digi_shutdown,
-+};
-+
-+static struct snd_soc_dai_link snd_rpi_hifiberry_digi_dai[] = {
-+{
-+ .name = "HifiBerry Digi",
-+ .stream_name = "HifiBerry Digi HiFi",
-+ .cpu_dai_name = "bcm2708-i2s.0",
-+ .codec_dai_name = "wm8804-spdif",
-+ .platform_name = "bcm2708-i2s.0",
-+ .codec_name = "wm8804.1-003b",
-+ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF |
-+ SND_SOC_DAIFMT_CBM_CFM,
-+ .ops = &snd_rpi_hifiberry_digi_ops,
-+ .init = snd_rpi_hifiberry_digi_init,
-+},
-+};
-+
-+/* audio machine driver */
-+static struct snd_soc_card snd_rpi_hifiberry_digi = {
-+ .name = "snd_rpi_hifiberry_digi",
-+ .dai_link = snd_rpi_hifiberry_digi_dai,
-+ .num_links = ARRAY_SIZE(snd_rpi_hifiberry_digi_dai),
-+};
-+
-+static int snd_rpi_hifiberry_digi_probe(struct platform_device *pdev)
-+{
-+ int ret = 0;
-+
-+ snd_rpi_hifiberry_digi.dev = &pdev->dev;
-+
-+ if (pdev->dev.of_node) {
-+ struct device_node *i2s_node;
-+ struct snd_soc_dai_link *dai = &snd_rpi_hifiberry_digi_dai[0];
-+ i2s_node = of_parse_phandle(pdev->dev.of_node,
-+ "i2s-controller", 0);
-+
-+ if (i2s_node) {
-+ dai->cpu_dai_name = NULL;
-+ dai->cpu_of_node = i2s_node;
-+ dai->platform_name = NULL;
-+ dai->platform_of_node = i2s_node;
-+ }
-+ }
-+
-+ ret = snd_soc_register_card(&snd_rpi_hifiberry_digi);
-+ if (ret)
-+ dev_err(&pdev->dev, "snd_soc_register_card() failed: %d\n", ret);
-+
-+ return ret;
-+}
-+
-+static int snd_rpi_hifiberry_digi_remove(struct platform_device *pdev)
-+{
-+ return snd_soc_unregister_card(&snd_rpi_hifiberry_digi);
-+}
-+
-+static const struct of_device_id snd_rpi_hifiberry_digi_of_match[] = {
-+ { .compatible = "hifiberry,hifiberry-digi", },
-+ {},
-+};
-+MODULE_DEVICE_TABLE(of, snd_rpi_hifiberry_digi_of_match);
-+
-+static struct platform_driver snd_rpi_hifiberry_digi_driver = {
-+ .driver = {
-+ .name = "snd-hifiberry-digi",
-+ .owner = THIS_MODULE,
-+ .of_match_table = snd_rpi_hifiberry_digi_of_match,
-+ },
-+ .probe = snd_rpi_hifiberry_digi_probe,
-+ .remove = snd_rpi_hifiberry_digi_remove,
-+};
-+
-+module_platform_driver(snd_rpi_hifiberry_digi_driver);
-+
-+MODULE_AUTHOR("Daniel Matuschek <info at crazy-audio.com>");
-+MODULE_DESCRIPTION("ASoC Driver for HifiBerry Digi");
-+MODULE_LICENSE("GPL v2");
diff --git a/target/linux/brcm2708/patches-4.4/0067-ASoC-wm8804-Set-idle_bias_off-to-false-Idle-bias-has.patch b/target/linux/brcm2708/patches-4.4/0067-ASoC-wm8804-Set-idle_bias_off-to-false-Idle-bias-has.patch
deleted file mode 100644
index 14397ff..0000000
--- a/target/linux/brcm2708/patches-4.4/0067-ASoC-wm8804-Set-idle_bias_off-to-false-Idle-bias-has.patch
+++ /dev/null
@@ -1,22 +0,0 @@
-From a388cc17079e2411e680504c6dfc292d179bdb68 Mon Sep 17 00:00:00 2001
-From: Daniel Matuschek <info at crazy-audio.com>
-Date: Thu, 16 Jan 2014 07:36:35 +0100
-Subject: [PATCH] ASoC: wm8804: Set idle_bias_off to false Idle bias has been
- change to remove warning on driver startup
-
-Signed-off-by: Daniel Matuschek <daniel at matuschek.net>
----
- sound/soc/codecs/wm8804.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/sound/soc/codecs/wm8804.c
-+++ b/sound/soc/codecs/wm8804.c
-@@ -544,7 +544,7 @@ static struct snd_soc_dai_driver wm8804_
- };
-
- static const struct snd_soc_codec_driver soc_codec_dev_wm8804 = {
-- .idle_bias_off = true,
-+ .idle_bias_off = false,
-
- .dapm_widgets = wm8804_dapm_widgets,
- .num_dapm_widgets = ARRAY_SIZE(wm8804_dapm_widgets),
diff --git a/target/linux/brcm2708/patches-4.4/0068-Add-IQaudIO-Sound-Card-support-for-Raspberry-Pi.patch b/target/linux/brcm2708/patches-4.4/0068-Add-IQaudIO-Sound-Card-support-for-Raspberry-Pi.patch
deleted file mode 100644
index fa6575a..0000000
--- a/target/linux/brcm2708/patches-4.4/0068-Add-IQaudIO-Sound-Card-support-for-Raspberry-Pi.patch
+++ /dev/null
@@ -1,178 +0,0 @@
-From 969d62154904b2a99a3531a41716025f281d96c5 Mon Sep 17 00:00:00 2001
-From: Gordon Garrity <gordon at iqaudio.com>
-Date: Sat, 8 Mar 2014 16:56:57 +0000
-Subject: [PATCH] Add IQaudIO Sound Card support for Raspberry Pi
-
-Set a limit of 0dB on Digital Volume Control
-
-The main volume control in the PCM512x DAC has a range up to
-+24dB. This is dangerously loud and can potentially cause massive
-clipping in the output stages. Therefore this sets a sensible
-limit of 0dB for this control.
----
- sound/soc/bcm/Kconfig | 7 +++
- sound/soc/bcm/Makefile | 2 +
- sound/soc/bcm/iqaudio-dac.c | 132 ++++++++++++++++++++++++++++++++++++++++++++
- 3 files changed, 141 insertions(+)
- create mode 100644 sound/soc/bcm/iqaudio-dac.c
-
---- a/sound/soc/bcm/Kconfig
-+++ b/sound/soc/bcm/Kconfig
-@@ -28,3 +28,10 @@ config SND_BCM2708_SOC_RPI_DAC
- select SND_SOC_PCM1794A
- help
- Say Y or M if you want to add support for RPi-DAC.
-+
-+config SND_BCM2708_SOC_IQAUDIO_DAC
-+ tristate "Support for IQaudIO-DAC"
-+ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
-+ select SND_SOC_PCM512x_I2C
-+ help
-+ Say Y or M if you want to add support for IQaudIO-DAC.
---- a/sound/soc/bcm/Makefile
-+++ b/sound/soc/bcm/Makefile
-@@ -7,7 +7,9 @@ obj-$(CONFIG_SND_BCM2835_SOC_I2S) += snd
- snd-soc-hifiberry-dac-objs := hifiberry_dac.o
- snd-soc-hifiberry-digi-objs := hifiberry_digi.o
- snd-soc-rpi-dac-objs := rpi-dac.o
-+snd-soc-iqaudio-dac-objs := iqaudio-dac.o
-
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DAC) += snd-soc-hifiberry-dac.o
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DIGI) += snd-soc-hifiberry-digi.o
- obj-$(CONFIG_SND_BCM2708_SOC_RPI_DAC) += snd-soc-rpi-dac.o
-+obj-$(CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC) += snd-soc-iqaudio-dac.o
---- /dev/null
-+++ b/sound/soc/bcm/iqaudio-dac.c
-@@ -0,0 +1,132 @@
-+/*
-+ * ASoC Driver for IQaudIO DAC
-+ *
-+ * Author: Florian Meier <florian.meier at koalo.de>
-+ * Copyright 2013
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * version 2 as published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful, but
-+ * WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
-+ * General Public License for more details.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+
-+#include <sound/core.h>
-+#include <sound/pcm.h>
-+#include <sound/pcm_params.h>
-+#include <sound/soc.h>
-+#include <sound/jack.h>
-+
-+static int snd_rpi_iqaudio_dac_init(struct snd_soc_pcm_runtime *rtd)
-+{
-+ int ret;
-+ struct snd_soc_card *card = rtd->card;
-+
-+ ret = snd_soc_limit_volume(card, "Digital Playback Volume", 207);
-+ if (ret < 0)
-+ dev_warn(card->dev, "Failed to set volume limit: %d\n", ret);
-+
-+ return 0;
-+}
-+
-+static int snd_rpi_iqaudio_dac_hw_params(struct snd_pcm_substream *substream,
-+ struct snd_pcm_hw_params *params)
-+{
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+// NOT USED struct snd_soc_dai *codec_dai = rtd->codec_dai;
-+// NOT USED struct snd_soc_codec *codec = rtd->codec;
-+ struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
-+
-+ unsigned int sample_bits =
-+ snd_pcm_format_physical_width(params_format(params));
-+
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, sample_bits * 2);
-+}
-+
-+/* machine stream operations */
-+static struct snd_soc_ops snd_rpi_iqaudio_dac_ops = {
-+ .hw_params = snd_rpi_iqaudio_dac_hw_params,
-+};
-+
-+static struct snd_soc_dai_link snd_rpi_iqaudio_dac_dai[] = {
-+{
-+ .name = "IQaudIO DAC",
-+ .stream_name = "IQaudIO DAC HiFi",
-+ .cpu_dai_name = "bcm2708-i2s.0",
-+ .codec_dai_name = "pcm512x-hifi",
-+ .platform_name = "bcm2708-i2s.0",
-+ .codec_name = "pcm512x.1-004c",
-+ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF |
-+ SND_SOC_DAIFMT_CBS_CFS,
-+ .ops = &snd_rpi_iqaudio_dac_ops,
-+ .init = snd_rpi_iqaudio_dac_init,
-+},
-+};
-+
-+/* audio machine driver */
-+static struct snd_soc_card snd_rpi_iqaudio_dac = {
-+ .name = "IQaudIODAC",
-+ .dai_link = snd_rpi_iqaudio_dac_dai,
-+ .num_links = ARRAY_SIZE(snd_rpi_iqaudio_dac_dai),
-+};
-+
-+static int snd_rpi_iqaudio_dac_probe(struct platform_device *pdev)
-+{
-+ int ret = 0;
-+
-+ snd_rpi_iqaudio_dac.dev = &pdev->dev;
-+
-+ if (pdev->dev.of_node) {
-+ struct device_node *i2s_node;
-+ struct snd_soc_dai_link *dai = &snd_rpi_iqaudio_dac_dai[0];
-+ i2s_node = of_parse_phandle(pdev->dev.of_node,
-+ "i2s-controller", 0);
-+
-+ if (i2s_node) {
-+ dai->cpu_dai_name = NULL;
-+ dai->cpu_of_node = i2s_node;
-+ dai->platform_name = NULL;
-+ dai->platform_of_node = i2s_node;
-+ }
-+ }
-+
-+ ret = snd_soc_register_card(&snd_rpi_iqaudio_dac);
-+ if (ret)
-+ dev_err(&pdev->dev,
-+ "snd_soc_register_card() failed: %d\n", ret);
-+
-+ return ret;
-+}
-+
-+static int snd_rpi_iqaudio_dac_remove(struct platform_device *pdev)
-+{
-+ return snd_soc_unregister_card(&snd_rpi_iqaudio_dac);
-+}
-+
-+static const struct of_device_id iqaudio_of_match[] = {
-+ { .compatible = "iqaudio,iqaudio-dac", },
-+ {},
-+};
-+MODULE_DEVICE_TABLE(of, iqaudio_of_match);
-+
-+static struct platform_driver snd_rpi_iqaudio_dac_driver = {
-+ .driver = {
-+ .name = "snd-rpi-iqaudio-dac",
-+ .owner = THIS_MODULE,
-+ .of_match_table = iqaudio_of_match,
-+ },
-+ .probe = snd_rpi_iqaudio_dac_probe,
-+ .remove = snd_rpi_iqaudio_dac_remove,
-+};
-+
-+module_platform_driver(snd_rpi_iqaudio_dac_driver);
-+
-+MODULE_AUTHOR("Florian Meier <florian.meier at koalo.de>");
-+MODULE_DESCRIPTION("ASoC Driver for IQAudio DAC");
-+MODULE_LICENSE("GPL v2");
diff --git a/target/linux/brcm2708/patches-4.4/0069-hid-Reduce-default-mouse-polling-interval-to-60Hz.patch b/target/linux/brcm2708/patches-4.4/0069-hid-Reduce-default-mouse-polling-interval-to-60Hz.patch
deleted file mode 100644
index 82c6edf..0000000
--- a/target/linux/brcm2708/patches-4.4/0069-hid-Reduce-default-mouse-polling-interval-to-60Hz.patch
+++ /dev/null
@@ -1,36 +0,0 @@
-From ff383d49e71e415d8482e9300b6c3c20e098bcef Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Mon, 14 Jul 2014 22:02:09 +0100
-Subject: [PATCH] hid: Reduce default mouse polling interval to 60Hz
-
-Reduces overhead when using X
----
- drivers/hid/usbhid/hid-core.c | 10 +++++++---
- 1 file changed, 7 insertions(+), 3 deletions(-)
-
---- a/drivers/hid/usbhid/hid-core.c
-+++ b/drivers/hid/usbhid/hid-core.c
-@@ -49,7 +49,7 @@
- * Module parameters.
- */
-
--static unsigned int hid_mousepoll_interval;
-+static unsigned int hid_mousepoll_interval = ~0;
- module_param_named(mousepoll, hid_mousepoll_interval, uint, 0644);
- MODULE_PARM_DESC(mousepoll, "Polling interval of mice");
-
-@@ -1083,8 +1083,12 @@ static int usbhid_start(struct hid_devic
- }
-
- /* Change the polling interval of mice. */
-- if (hid->collection->usage == HID_GD_MOUSE && hid_mousepoll_interval > 0)
-- interval = hid_mousepoll_interval;
-+ if (hid->collection->usage == HID_GD_MOUSE) {
-+ if (hid_mousepoll_interval == ~0 && interval < 16)
-+ interval = 16;
-+ else if (hid_mousepoll_interval != ~0 && hid_mousepoll_interval != 0)
-+ interval = hid_mousepoll_interval;
-+ }
-
- ret = -ENOMEM;
- if (usb_endpoint_dir_in(endpoint)) {
diff --git a/target/linux/brcm2708/patches-4.4/0070-Added-support-for-HiFiBerry-DAC.patch b/target/linux/brcm2708/patches-4.4/0070-Added-support-for-HiFiBerry-DAC.patch
deleted file mode 100644
index b2dc190..0000000
--- a/target/linux/brcm2708/patches-4.4/0070-Added-support-for-HiFiBerry-DAC.patch
+++ /dev/null
@@ -1,190 +0,0 @@
-From 754ad5a8702de8e194d1fb185b451b1e39285dea Mon Sep 17 00:00:00 2001
-From: Daniel Matuschek <info at crazy-audio.com>
-Date: Mon, 4 Aug 2014 10:06:56 +0200
-Subject: [PATCH] Added support for HiFiBerry DAC+
-
-The driver is based on the HiFiBerry DAC driver. However HiFiBerry DAC+ uses
-a different codec chip (PCM5122), therefore a new driver is necessary.
----
- sound/soc/bcm/Kconfig | 7 ++
- sound/soc/bcm/Makefile | 2 +
- sound/soc/bcm/hifiberry_dacplus.c | 141 ++++++++++++++++++++++++++++++++++++++
- 3 files changed, 150 insertions(+)
- create mode 100644 sound/soc/bcm/hifiberry_dacplus.c
-
---- a/sound/soc/bcm/Kconfig
-+++ b/sound/soc/bcm/Kconfig
-@@ -15,6 +15,13 @@ config SND_BCM2708_SOC_HIFIBERRY_DAC
- help
- Say Y or M if you want to add support for HifiBerry DAC.
-
-+config SND_BCM2708_SOC_HIFIBERRY_DACPLUS
-+ tristate "Support for HifiBerry DAC+"
-+ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
-+ select SND_SOC_PCM512x
-+ help
-+ Say Y or M if you want to add support for HifiBerry DAC+.
-+
- config SND_BCM2708_SOC_HIFIBERRY_DIGI
- tristate "Support for HifiBerry Digi"
- depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
---- a/sound/soc/bcm/Makefile
-+++ b/sound/soc/bcm/Makefile
-@@ -5,11 +5,13 @@ obj-$(CONFIG_SND_BCM2835_SOC_I2S) += snd
-
- # BCM2708 Machine Support
- snd-soc-hifiberry-dac-objs := hifiberry_dac.o
-+snd-soc-hifiberry-dacplus-objs := hifiberry_dacplus.o
- snd-soc-hifiberry-digi-objs := hifiberry_digi.o
- snd-soc-rpi-dac-objs := rpi-dac.o
- snd-soc-iqaudio-dac-objs := iqaudio-dac.o
-
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DAC) += snd-soc-hifiberry-dac.o
-+obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DACPLUS) += snd-soc-hifiberry-dacplus.o
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DIGI) += snd-soc-hifiberry-digi.o
- obj-$(CONFIG_SND_BCM2708_SOC_RPI_DAC) += snd-soc-rpi-dac.o
- obj-$(CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC) += snd-soc-iqaudio-dac.o
---- /dev/null
-+++ b/sound/soc/bcm/hifiberry_dacplus.c
-@@ -0,0 +1,141 @@
-+/*
-+ * ASoC Driver for HiFiBerry DAC+
-+ *
-+ * Author: Daniel Matuschek
-+ * Copyright 2014
-+ * based on code by Florian Meier <florian.meier at koalo.de>
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * version 2 as published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful, but
-+ * WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
-+ * General Public License for more details.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+
-+#include <sound/core.h>
-+#include <sound/pcm.h>
-+#include <sound/pcm_params.h>
-+#include <sound/soc.h>
-+#include <sound/jack.h>
-+
-+#include "../codecs/pcm512x.h"
-+
-+static int snd_rpi_hifiberry_dacplus_init(struct snd_soc_pcm_runtime *rtd)
-+{
-+ struct snd_soc_codec *codec = rtd->codec;
-+ snd_soc_update_bits(codec, PCM512x_GPIO_EN, 0x08, 0x08);
-+ snd_soc_update_bits(codec, PCM512x_GPIO_OUTPUT_4, 0xf, 0x02);
-+ snd_soc_update_bits(codec, PCM512x_GPIO_CONTROL_1, 0x08,0x08);
-+ return 0;
-+}
-+
-+static int snd_rpi_hifiberry_dacplus_hw_params(struct snd_pcm_substream *substream,
-+ struct snd_pcm_hw_params *params)
-+{
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, 64);
-+}
-+
-+static int snd_rpi_hifiberry_dacplus_startup(struct snd_pcm_substream *substream) {
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_codec *codec = rtd->codec;
-+ snd_soc_update_bits(codec, PCM512x_GPIO_CONTROL_1, 0x08,0x08);
-+ return 0;
-+}
-+
-+static void snd_rpi_hifiberry_dacplus_shutdown(struct snd_pcm_substream *substream) {
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_codec *codec = rtd->codec;
-+ snd_soc_update_bits(codec, PCM512x_GPIO_CONTROL_1, 0x08,0x00);
-+}
-+
-+/* machine stream operations */
-+static struct snd_soc_ops snd_rpi_hifiberry_dacplus_ops = {
-+ .hw_params = snd_rpi_hifiberry_dacplus_hw_params,
-+ .startup = snd_rpi_hifiberry_dacplus_startup,
-+ .shutdown = snd_rpi_hifiberry_dacplus_shutdown,
-+};
-+
-+static struct snd_soc_dai_link snd_rpi_hifiberry_dacplus_dai[] = {
-+{
-+ .name = "HiFiBerry DAC+",
-+ .stream_name = "HiFiBerry DAC+ HiFi",
-+ .cpu_dai_name = "bcm2708-i2s.0",
-+ .codec_dai_name = "pcm512x-hifi",
-+ .platform_name = "bcm2708-i2s.0",
-+ .codec_name = "pcm512x.1-004d",
-+ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF |
-+ SND_SOC_DAIFMT_CBS_CFS,
-+ .ops = &snd_rpi_hifiberry_dacplus_ops,
-+ .init = snd_rpi_hifiberry_dacplus_init,
-+},
-+};
-+
-+/* audio machine driver */
-+static struct snd_soc_card snd_rpi_hifiberry_dacplus = {
-+ .name = "snd_rpi_hifiberry_dacplus",
-+ .dai_link = snd_rpi_hifiberry_dacplus_dai,
-+ .num_links = ARRAY_SIZE(snd_rpi_hifiberry_dacplus_dai),
-+};
-+
-+static int snd_rpi_hifiberry_dacplus_probe(struct platform_device *pdev)
-+{
-+ int ret = 0;
-+
-+ snd_rpi_hifiberry_dacplus.dev = &pdev->dev;
-+
-+ if (pdev->dev.of_node) {
-+ struct device_node *i2s_node;
-+ struct snd_soc_dai_link *dai = &snd_rpi_hifiberry_dacplus_dai[0];
-+ i2s_node = of_parse_phandle(pdev->dev.of_node,
-+ "i2s-controller", 0);
-+
-+ if (i2s_node) {
-+ dai->cpu_dai_name = NULL;
-+ dai->cpu_of_node = i2s_node;
-+ dai->platform_name = NULL;
-+ dai->platform_of_node = i2s_node;
-+ }
-+ }
-+
-+ ret = snd_soc_register_card(&snd_rpi_hifiberry_dacplus);
-+ if (ret)
-+ dev_err(&pdev->dev,
-+ "snd_soc_register_card() failed: %d\n", ret);
-+
-+ return ret;
-+}
-+
-+static int snd_rpi_hifiberry_dacplus_remove(struct platform_device *pdev)
-+{
-+ return snd_soc_unregister_card(&snd_rpi_hifiberry_dacplus);
-+}
-+
-+static const struct of_device_id snd_rpi_hifiberry_dacplus_of_match[] = {
-+ { .compatible = "hifiberry,hifiberry-dacplus", },
-+ {},
-+};
-+MODULE_DEVICE_TABLE(of, snd_rpi_hifiberry_dacplus_of_match);
-+
-+static struct platform_driver snd_rpi_hifiberry_dacplus_driver = {
-+ .driver = {
-+ .name = "snd-rpi-hifiberry-dacplus",
-+ .owner = THIS_MODULE,
-+ .of_match_table = snd_rpi_hifiberry_dacplus_of_match,
-+ },
-+ .probe = snd_rpi_hifiberry_dacplus_probe,
-+ .remove = snd_rpi_hifiberry_dacplus_remove,
-+};
-+
-+module_platform_driver(snd_rpi_hifiberry_dacplus_driver);
-+
-+MODULE_AUTHOR("Daniel Matuschek <daniel at hifiberry.com>");
-+MODULE_DESCRIPTION("ASoC Driver for HiFiBerry DAC+");
-+MODULE_LICENSE("GPL v2");
diff --git a/target/linux/brcm2708/patches-4.4/0071-Added-driver-for-HiFiBerry-Amp-amplifier-add-on-boar.patch b/target/linux/brcm2708/patches-4.4/0071-Added-driver-for-HiFiBerry-Amp-amplifier-add-on-boar.patch
deleted file mode 100644
index acf8c67..0000000
--- a/target/linux/brcm2708/patches-4.4/0071-Added-driver-for-HiFiBerry-Amp-amplifier-add-on-boar.patch
+++ /dev/null
@@ -1,816 +0,0 @@
-From e45e0b8804ee1cf5ed841c021c82bc9f9a888ed3 Mon Sep 17 00:00:00 2001
-From: Daniel Matuschek <info at crazy-audio.com>
-Date: Mon, 4 Aug 2014 11:09:58 +0200
-Subject: [PATCH] Added driver for HiFiBerry Amp amplifier add-on board
-
-The driver contains a low-level hardware driver for the TAS5713 and the
-drivers for the Raspberry Pi I2S subsystem.
-
-TAS5713: return error if initialisation fails
-
-Existing TAS5713 driver logs errors during initialisation, but does not return
-an error code. Therefore even if initialisation fails, the driver will still be
-loaded, but won't work. This patch fixes this. I2C communication error will now
-reported correctly by a non-zero return code.
-
-HiFiBerry Amp: fix device-tree problems
-
-Some code to load the driver based on device-tree-overlays was missing. This is added by this patch.
----
- sound/soc/bcm/Kconfig | 7 +
- sound/soc/bcm/Makefile | 2 +
- sound/soc/bcm/hifiberry_amp.c | 127 +++++++++++++++
- sound/soc/codecs/Kconfig | 4 +
- sound/soc/codecs/Makefile | 2 +
- sound/soc/codecs/tas5713.c | 369 ++++++++++++++++++++++++++++++++++++++++++
- sound/soc/codecs/tas5713.h | 210 ++++++++++++++++++++++++
- 7 files changed, 721 insertions(+)
- create mode 100644 sound/soc/bcm/hifiberry_amp.c
- create mode 100644 sound/soc/codecs/tas5713.c
- create mode 100644 sound/soc/codecs/tas5713.h
-
---- a/sound/soc/bcm/Kconfig
-+++ b/sound/soc/bcm/Kconfig
-@@ -29,6 +29,13 @@ config SND_BCM2708_SOC_HIFIBERRY_DIGI
- help
- Say Y or M if you want to add support for HifiBerry Digi S/PDIF output board.
-
-+config SND_BCM2708_SOC_HIFIBERRY_AMP
-+ tristate "Support for the HifiBerry Amp"
-+ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
-+ select SND_SOC_TAS5713
-+ help
-+ Say Y or M if you want to add support for the HifiBerry Amp amplifier board.
-+
- config SND_BCM2708_SOC_RPI_DAC
- tristate "Support for RPi-DAC"
- depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
---- a/sound/soc/bcm/Makefile
-+++ b/sound/soc/bcm/Makefile
-@@ -7,11 +7,13 @@ obj-$(CONFIG_SND_BCM2835_SOC_I2S) += snd
- snd-soc-hifiberry-dac-objs := hifiberry_dac.o
- snd-soc-hifiberry-dacplus-objs := hifiberry_dacplus.o
- snd-soc-hifiberry-digi-objs := hifiberry_digi.o
-+snd-soc-hifiberry-amp-objs := hifiberry_amp.o
- snd-soc-rpi-dac-objs := rpi-dac.o
- snd-soc-iqaudio-dac-objs := iqaudio-dac.o
-
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DAC) += snd-soc-hifiberry-dac.o
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DACPLUS) += snd-soc-hifiberry-dacplus.o
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DIGI) += snd-soc-hifiberry-digi.o
-+obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_AMP) += snd-soc-hifiberry-amp.o
- obj-$(CONFIG_SND_BCM2708_SOC_RPI_DAC) += snd-soc-rpi-dac.o
- obj-$(CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC) += snd-soc-iqaudio-dac.o
---- /dev/null
-+++ b/sound/soc/bcm/hifiberry_amp.c
-@@ -0,0 +1,127 @@
-+/*
-+ * ASoC Driver for HifiBerry AMP
-+ *
-+ * Author: Sebastian Eickhoff <basti.eickhoff at googlemail.com>
-+ * Copyright 2014
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * version 2 as published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful, but
-+ * WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
-+ * General Public License for more details.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+
-+#include <sound/core.h>
-+#include <sound/pcm.h>
-+#include <sound/pcm_params.h>
-+#include <sound/soc.h>
-+#include <sound/jack.h>
-+
-+static int snd_rpi_hifiberry_amp_init(struct snd_soc_pcm_runtime *rtd)
-+{
-+ // ToDo: init of the dsp-registers.
-+ return 0;
-+}
-+
-+static int snd_rpi_hifiberry_amp_hw_params( struct snd_pcm_substream *substream,
-+ struct snd_pcm_hw_params *params )
-+{
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
-+
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, 64);
-+}
-+
-+static struct snd_soc_ops snd_rpi_hifiberry_amp_ops = {
-+ .hw_params = snd_rpi_hifiberry_amp_hw_params,
-+};
-+
-+static struct snd_soc_dai_link snd_rpi_hifiberry_amp_dai[] = {
-+ {
-+ .name = "HifiBerry AMP",
-+ .stream_name = "HifiBerry AMP HiFi",
-+ .cpu_dai_name = "bcm2708-i2s.0",
-+ .codec_dai_name = "tas5713-hifi",
-+ .platform_name = "bcm2708-i2s.0",
-+ .codec_name = "tas5713.1-001b",
-+ .dai_fmt = SND_SOC_DAIFMT_I2S |
-+ SND_SOC_DAIFMT_NB_NF |
-+ SND_SOC_DAIFMT_CBS_CFS,
-+ .ops = &snd_rpi_hifiberry_amp_ops,
-+ .init = snd_rpi_hifiberry_amp_init,
-+ },
-+};
-+
-+
-+static struct snd_soc_card snd_rpi_hifiberry_amp = {
-+ .name = "snd_rpi_hifiberry_amp",
-+ .dai_link = snd_rpi_hifiberry_amp_dai,
-+ .num_links = ARRAY_SIZE(snd_rpi_hifiberry_amp_dai),
-+};
-+
-+static const struct of_device_id snd_rpi_hifiberry_amp_of_match[] = {
-+ { .compatible = "hifiberry,hifiberry-amp", },
-+ {},
-+};
-+MODULE_DEVICE_TABLE(of, snd_rpi_hifiberry_amp_of_match);
-+
-+
-+static int snd_rpi_hifiberry_amp_probe(struct platform_device *pdev)
-+{
-+ int ret = 0;
-+
-+ snd_rpi_hifiberry_amp.dev = &pdev->dev;
-+
-+ if (pdev->dev.of_node) {
-+ struct device_node *i2s_node;
-+ struct snd_soc_dai_link *dai = &snd_rpi_hifiberry_amp_dai[0];
-+ i2s_node = of_parse_phandle(pdev->dev.of_node,
-+ "i2s-controller", 0);
-+
-+ if (i2s_node) {
-+ dai->cpu_dai_name = NULL;
-+ dai->cpu_of_node = i2s_node;
-+ dai->platform_name = NULL;
-+ dai->platform_of_node = i2s_node;
-+ }
-+ }
-+
-+ ret = snd_soc_register_card(&snd_rpi_hifiberry_amp);
-+
-+ if (ret != 0) {
-+ dev_err(&pdev->dev, "snd_soc_register_card() failed: %d\n", ret);
-+ }
-+
-+ return ret;
-+}
-+
-+
-+static int snd_rpi_hifiberry_amp_remove(struct platform_device *pdev)
-+{
-+ return snd_soc_unregister_card(&snd_rpi_hifiberry_amp);
-+}
-+
-+
-+static struct platform_driver snd_rpi_hifiberry_amp_driver = {
-+ .driver = {
-+ .name = "snd-hifiberry-amp",
-+ .owner = THIS_MODULE,
-+ .of_match_table = snd_rpi_hifiberry_amp_of_match,
-+ },
-+ .probe = snd_rpi_hifiberry_amp_probe,
-+ .remove = snd_rpi_hifiberry_amp_remove,
-+};
-+
-+
-+module_platform_driver(snd_rpi_hifiberry_amp_driver);
-+
-+
-+MODULE_AUTHOR("Sebastian Eickhoff <basti.eickhoff at googlemail.com>");
-+MODULE_DESCRIPTION("ASoC driver for HiFiBerry-AMP");
-+MODULE_LICENSE("GPL v2");
---- a/sound/soc/codecs/Kconfig
-+++ b/sound/soc/codecs/Kconfig
-@@ -117,6 +117,7 @@ config SND_SOC_ALL_CODECS
- select SND_SOC_TFA9879 if I2C
- select SND_SOC_TLV320AIC23_I2C if I2C
- select SND_SOC_TLV320AIC23_SPI if SPI_MASTER
-+ select SND_SOC_TAS5713 if I2C
- select SND_SOC_TLV320AIC26 if SPI_MASTER
- select SND_SOC_TLV320AIC31XX if I2C
- select SND_SOC_TLV320AIC32X4 if I2C
-@@ -674,6 +675,9 @@ config SND_SOC_TFA9879
- tristate "NXP Semiconductors TFA9879 amplifier"
- depends on I2C
-
-+config SND_SOC_TAS5713
-+ tristate
-+
- config SND_SOC_TLV320AIC23
- tristate
-
---- a/sound/soc/codecs/Makefile
-+++ b/sound/soc/codecs/Makefile
-@@ -118,6 +118,7 @@ snd-soc-sti-sas-objs := sti-sas.o
- snd-soc-tas5086-objs := tas5086.o
- snd-soc-tas571x-objs := tas571x.o
- snd-soc-tfa9879-objs := tfa9879.o
-+snd-soc-tas5713-objs := tas5713.o
- snd-soc-tlv320aic23-objs := tlv320aic23.o
- snd-soc-tlv320aic23-i2c-objs := tlv320aic23-i2c.o
- snd-soc-tlv320aic23-spi-objs := tlv320aic23-spi.o
-@@ -312,6 +313,7 @@ obj-$(CONFIG_SND_SOC_TAS2552) += snd-soc
- obj-$(CONFIG_SND_SOC_TAS5086) += snd-soc-tas5086.o
- obj-$(CONFIG_SND_SOC_TAS571X) += snd-soc-tas571x.o
- obj-$(CONFIG_SND_SOC_TFA9879) += snd-soc-tfa9879.o
-+obj-$(CONFIG_SND_SOC_TAS5713) += snd-soc-tas5713.o
- obj-$(CONFIG_SND_SOC_TLV320AIC23) += snd-soc-tlv320aic23.o
- obj-$(CONFIG_SND_SOC_TLV320AIC23_I2C) += snd-soc-tlv320aic23-i2c.o
- obj-$(CONFIG_SND_SOC_TLV320AIC23_SPI) += snd-soc-tlv320aic23-spi.o
---- /dev/null
-+++ b/sound/soc/codecs/tas5713.c
-@@ -0,0 +1,369 @@
-+/*
-+ * ASoC Driver for TAS5713
-+ *
-+ * Author: Sebastian Eickhoff <basti.eickhoff at googlemail.com>
-+ * Copyright 2014
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * version 2 as published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful, but
-+ * WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
-+ * General Public License for more details.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/moduleparam.h>
-+#include <linux/init.h>
-+#include <linux/delay.h>
-+#include <linux/pm.h>
-+#include <linux/i2c.h>
-+#include <linux/of_device.h>
-+#include <linux/spi/spi.h>
-+#include <linux/regmap.h>
-+#include <linux/regulator/consumer.h>
-+#include <linux/slab.h>
-+#include <sound/core.h>
-+#include <sound/pcm.h>
-+#include <sound/pcm_params.h>
-+#include <sound/soc.h>
-+#include <sound/initval.h>
-+#include <sound/tlv.h>
-+
-+#include <linux/kernel.h>
-+#include <linux/string.h>
-+#include <linux/fs.h>
-+#include <asm/uaccess.h>
-+
-+#include "tas5713.h"
-+
-+
-+static struct i2c_client *i2c;
-+
-+struct tas5713_priv {
-+ struct regmap *regmap;
-+ int mclk_div;
-+ struct snd_soc_codec *codec;
-+};
-+
-+static struct tas5713_priv *priv_data;
-+
-+
-+
-+
-+/*
-+ * _ _ ___ _ ___ _ _
-+ * /_\ | | / __| /_\ / __|___ _ _| |_ _ _ ___| |___
-+ * / _ \| |__\__ \/ _ \ | (__/ _ \ ' \ _| '_/ _ \ (_-<
-+ * /_/ \_\____|___/_/ \_\ \___\___/_||_\__|_| \___/_/__/
-+ *
-+ */
-+
-+static const DECLARE_TLV_DB_SCALE(tas5713_vol_tlv, -10000, 50, 1);
-+
-+
-+static const struct snd_kcontrol_new tas5713_snd_controls[] = {
-+ SOC_SINGLE_TLV ("Master" , TAS5713_VOL_MASTER, 0, 248, 1, tas5713_vol_tlv),
-+ SOC_DOUBLE_R_TLV("Channels" , TAS5713_VOL_CH1, TAS5713_VOL_CH2, 0, 248, 1, tas5713_vol_tlv)
-+};
-+
-+
-+
-+
-+/*
-+ * __ __ _ _ ___ _
-+ * | \/ |__ _ __| |_ (_)_ _ ___ | \ _ _(_)_ _____ _ _
-+ * | |\/| / _` / _| ' \| | ' \/ -_) | |) | '_| \ V / -_) '_|
-+ * |_| |_\__,_\__|_||_|_|_||_\___| |___/|_| |_|\_/\___|_|
-+ *
-+ */
-+
-+static int tas5713_hw_params(struct snd_pcm_substream *substream,
-+ struct snd_pcm_hw_params *params,
-+ struct snd_soc_dai *dai)
-+{
-+ u16 blen = 0x00;
-+
-+ struct snd_soc_codec *codec;
-+ codec = dai->codec;
-+ priv_data->codec = dai->codec;
-+
-+ switch (params_format(params)) {
-+ case SNDRV_PCM_FORMAT_S16_LE:
-+ blen = 0x03;
-+ break;
-+ case SNDRV_PCM_FORMAT_S20_3LE:
-+ blen = 0x1;
-+ break;
-+ case SNDRV_PCM_FORMAT_S24_LE:
-+ blen = 0x04;
-+ break;
-+ case SNDRV_PCM_FORMAT_S32_LE:
-+ blen = 0x05;
-+ break;
-+ default:
-+ dev_err(dai->dev, "Unsupported word length: %u\n",
-+ params_format(params));
-+ return -EINVAL;
-+ }
-+
-+ // set word length
-+ snd_soc_update_bits(codec, TAS5713_SERIAL_DATA_INTERFACE, 0x7, blen);
-+
-+ return 0;
-+}
-+
-+
-+static int tas5713_mute_stream(struct snd_soc_dai *dai, int mute, int stream)
-+{
-+ unsigned int val = 0;
-+
-+ struct tas5713_priv *tas5713;
-+ struct snd_soc_codec *codec = dai->codec;
-+ tas5713 = snd_soc_codec_get_drvdata(codec);
-+
-+ if (mute) {
-+ val = TAS5713_SOFT_MUTE_ALL;
-+ }
-+
-+ return regmap_write(tas5713->regmap, TAS5713_SOFT_MUTE, val);
-+}
-+
-+
-+static const struct snd_soc_dai_ops tas5713_dai_ops = {
-+ .hw_params = tas5713_hw_params,
-+ .mute_stream = tas5713_mute_stream,
-+};
-+
-+
-+static struct snd_soc_dai_driver tas5713_dai = {
-+ .name = "tas5713-hifi",
-+ .playback = {
-+ .stream_name = "Playback",
-+ .channels_min = 2,
-+ .channels_max = 2,
-+ .rates = SNDRV_PCM_RATE_8000_48000,
-+ .formats = (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S24_LE | SNDRV_PCM_FMTBIT_S32_LE ),
-+ },
-+ .ops = &tas5713_dai_ops,
-+};
-+
-+
-+
-+
-+/*
-+ * ___ _ ___ _
-+ * / __|___ __| |___ __ | \ _ _(_)_ _____ _ _
-+ * | (__/ _ \/ _` / -_) _| | |) | '_| \ V / -_) '_|
-+ * \___\___/\__,_\___\__| |___/|_| |_|\_/\___|_|
-+ *
-+ */
-+
-+static int tas5713_remove(struct snd_soc_codec *codec)
-+{
-+ struct tas5713_priv *tas5713;
-+
-+ tas5713 = snd_soc_codec_get_drvdata(codec);
-+
-+ return 0;
-+}
-+
-+
-+static int tas5713_probe(struct snd_soc_codec *codec)
-+{
-+ struct tas5713_priv *tas5713;
-+ int i, ret;
-+
-+ i2c = container_of(codec->dev, struct i2c_client, dev);
-+
-+ tas5713 = snd_soc_codec_get_drvdata(codec);
-+
-+ // Reset error
-+ ret = snd_soc_write(codec, TAS5713_ERROR_STATUS, 0x00);
-+ if (ret < 0) return ret;
-+
-+ // Trim oscillator
-+ ret = snd_soc_write(codec, TAS5713_OSC_TRIM, 0x00);
-+ if (ret < 0) return ret;
-+ msleep(1000);
-+
-+ // Reset error
-+ ret = snd_soc_write(codec, TAS5713_ERROR_STATUS, 0x00);
-+ if (ret < 0) return ret;
-+
-+ // Clock mode: 44/48kHz, MCLK=64xfs
-+ ret = snd_soc_write(codec, TAS5713_CLOCK_CTRL, 0x60);
-+ if (ret < 0) return ret;
-+
-+ // I2S 24bit
-+ ret = snd_soc_write(codec, TAS5713_SERIAL_DATA_INTERFACE, 0x05);
-+ if (ret < 0) return ret;
-+
-+ // Unmute
-+ ret = snd_soc_write(codec, TAS5713_SYSTEM_CTRL2, 0x00);
-+ if (ret < 0) return ret;
-+ ret = snd_soc_write(codec, TAS5713_SOFT_MUTE, 0x00);
-+ if (ret < 0) return ret;
-+
-+ // Set volume to 0db
-+ ret = snd_soc_write(codec, TAS5713_VOL_MASTER, 0x00);
-+ if (ret < 0) return ret;
-+
-+ // Now start programming the default initialization sequence
-+ for (i = 0; i < ARRAY_SIZE(tas5713_init_sequence); ++i) {
-+ ret = i2c_master_send(i2c,
-+ tas5713_init_sequence[i].data,
-+ tas5713_init_sequence[i].size);
-+ if (ret < 0) {
-+ printk(KERN_INFO "TAS5713 CODEC PROBE: InitSeq returns: %d\n", ret);
-+ }
-+ }
-+
-+ // Unmute
-+ ret = snd_soc_write(codec, TAS5713_SYSTEM_CTRL2, 0x00);
-+ if (ret < 0) return ret;
-+
-+ return 0;
-+}
-+
-+
-+static struct snd_soc_codec_driver soc_codec_dev_tas5713 = {
-+ .probe = tas5713_probe,
-+ .remove = tas5713_remove,
-+ .controls = tas5713_snd_controls,
-+ .num_controls = ARRAY_SIZE(tas5713_snd_controls),
-+};
-+
-+
-+
-+
-+/*
-+ * ___ ___ ___ ___ _
-+ * |_ _|_ ) __| | \ _ _(_)_ _____ _ _
-+ * | | / / (__ | |) | '_| \ V / -_) '_|
-+ * |___/___\___| |___/|_| |_|\_/\___|_|
-+ *
-+ */
-+
-+static const struct reg_default tas5713_reg_defaults[] = {
-+ { 0x07 ,0x80 }, // R7 - VOL_MASTER - -40dB
-+ { 0x08 , 30 }, // R8 - VOL_CH1 - 0dB
-+ { 0x09 , 30 }, // R9 - VOL_CH2 - 0dB
-+ { 0x0A ,0x80 }, // R10 - VOL_HEADPHONE - -40dB
-+};
-+
-+
-+static bool tas5713_reg_volatile(struct device *dev, unsigned int reg)
-+{
-+ switch (reg) {
-+ case TAS5713_DEVICE_ID:
-+ case TAS5713_ERROR_STATUS:
-+ return true;
-+ default:
-+ return false;
-+ }
-+}
-+
-+
-+static const struct of_device_id tas5713_of_match[] = {
-+ { .compatible = "ti,tas5713", },
-+ { }
-+};
-+MODULE_DEVICE_TABLE(of, tas5713_of_match);
-+
-+
-+static struct regmap_config tas5713_regmap_config = {
-+ .reg_bits = 8,
-+ .val_bits = 8,
-+
-+ .max_register = TAS5713_MAX_REGISTER,
-+ .volatile_reg = tas5713_reg_volatile,
-+
-+ .cache_type = REGCACHE_RBTREE,
-+ .reg_defaults = tas5713_reg_defaults,
-+ .num_reg_defaults = ARRAY_SIZE(tas5713_reg_defaults),
-+};
-+
-+
-+static int tas5713_i2c_probe(struct i2c_client *i2c,
-+ const struct i2c_device_id *id)
-+{
-+ int ret;
-+
-+ priv_data = devm_kzalloc(&i2c->dev, sizeof *priv_data, GFP_KERNEL);
-+ if (!priv_data)
-+ return -ENOMEM;
-+
-+ priv_data->regmap = devm_regmap_init_i2c(i2c, &tas5713_regmap_config);
-+ if (IS_ERR(priv_data->regmap)) {
-+ ret = PTR_ERR(priv_data->regmap);
-+ return ret;
-+ }
-+
-+ i2c_set_clientdata(i2c, priv_data);
-+
-+ ret = snd_soc_register_codec(&i2c->dev,
-+ &soc_codec_dev_tas5713, &tas5713_dai, 1);
-+
-+ return ret;
-+}
-+
-+
-+static int tas5713_i2c_remove(struct i2c_client *i2c)
-+{
-+ snd_soc_unregister_codec(&i2c->dev);
-+ i2c_set_clientdata(i2c, NULL);
-+
-+ kfree(priv_data);
-+
-+ return 0;
-+}
-+
-+
-+static const struct i2c_device_id tas5713_i2c_id[] = {
-+ { "tas5713", 0 },
-+ { }
-+};
-+
-+MODULE_DEVICE_TABLE(i2c, tas5713_i2c_id);
-+
-+
-+static struct i2c_driver tas5713_i2c_driver = {
-+ .driver = {
-+ .name = "tas5713",
-+ .owner = THIS_MODULE,
-+ .of_match_table = tas5713_of_match,
-+ },
-+ .probe = tas5713_i2c_probe,
-+ .remove = tas5713_i2c_remove,
-+ .id_table = tas5713_i2c_id
-+};
-+
-+
-+static int __init tas5713_modinit(void)
-+{
-+ int ret = 0;
-+
-+ ret = i2c_add_driver(&tas5713_i2c_driver);
-+ if (ret) {
-+ printk(KERN_ERR "Failed to register tas5713 I2C driver: %d\n",
-+ ret);
-+ }
-+
-+ return ret;
-+}
-+module_init(tas5713_modinit);
-+
-+
-+static void __exit tas5713_exit(void)
-+{
-+ i2c_del_driver(&tas5713_i2c_driver);
-+}
-+module_exit(tas5713_exit);
-+
-+
-+MODULE_AUTHOR("Sebastian Eickhoff <basti.eickhoff at googlemail.com>");
-+MODULE_DESCRIPTION("ASoC driver for TAS5713");
-+MODULE_LICENSE("GPL v2");
---- /dev/null
-+++ b/sound/soc/codecs/tas5713.h
-@@ -0,0 +1,210 @@
-+/*
-+ * ASoC Driver for TAS5713
-+ *
-+ * Author: Sebastian Eickhoff <basti.eickhoff at googlemail.com>
-+ * Copyright 2014
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * version 2 as published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful, but
-+ * WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
-+ * General Public License for more details.
-+ */
-+
-+#ifndef _TAS5713_H
-+#define _TAS5713_H
-+
-+
-+// TAS5713 I2C-bus register addresses
-+
-+#define TAS5713_CLOCK_CTRL 0x00
-+#define TAS5713_DEVICE_ID 0x01
-+#define TAS5713_ERROR_STATUS 0x02
-+#define TAS5713_SYSTEM_CTRL1 0x03
-+#define TAS5713_SERIAL_DATA_INTERFACE 0x04
-+#define TAS5713_SYSTEM_CTRL2 0x05
-+#define TAS5713_SOFT_MUTE 0x06
-+#define TAS5713_VOL_MASTER 0x07
-+#define TAS5713_VOL_CH1 0x08
-+#define TAS5713_VOL_CH2 0x09
-+#define TAS5713_VOL_HEADPHONE 0x0A
-+#define TAS5713_VOL_CONFIG 0x0E
-+#define TAS5713_MODULATION_LIMIT 0x10
-+#define TAS5713_IC_DLY_CH1 0x11
-+#define TAS5713_IC_DLY_CH2 0x12
-+#define TAS5713_IC_DLY_CH3 0x13
-+#define TAS5713_IC_DLY_CH4 0x14
-+
-+#define TAS5713_START_STOP_PERIOD 0x1A
-+#define TAS5713_OSC_TRIM 0x1B
-+#define TAS5713_BKND_ERR 0x1C
-+
-+#define TAS5713_INPUT_MUX 0x20
-+#define TAS5713_SRC_SELECT_CH4 0x21
-+#define TAS5713_PWM_MUX 0x25
-+
-+#define TAS5713_CH1_BQ0 0x29
-+#define TAS5713_CH1_BQ1 0x2A
-+#define TAS5713_CH1_BQ2 0x2B
-+#define TAS5713_CH1_BQ3 0x2C
-+#define TAS5713_CH1_BQ4 0x2D
-+#define TAS5713_CH1_BQ5 0x2E
-+#define TAS5713_CH1_BQ6 0x2F
-+#define TAS5713_CH1_BQ7 0x58
-+#define TAS5713_CH1_BQ8 0x59
-+
-+#define TAS5713_CH2_BQ0 0x30
-+#define TAS5713_CH2_BQ1 0x31
-+#define TAS5713_CH2_BQ2 0x32
-+#define TAS5713_CH2_BQ3 0x33
-+#define TAS5713_CH2_BQ4 0x34
-+#define TAS5713_CH2_BQ5 0x35
-+#define TAS5713_CH2_BQ6 0x36
-+#define TAS5713_CH2_BQ7 0x5C
-+#define TAS5713_CH2_BQ8 0x5D
-+
-+#define TAS5713_CH4_BQ0 0x5A
-+#define TAS5713_CH4_BQ1 0x5B
-+#define TAS5713_CH3_BQ0 0x5E
-+#define TAS5713_CH3_BQ1 0x5F
-+
-+#define TAS5713_DRC1_SOFTENING_FILTER_ALPHA_OMEGA 0x3B
-+#define TAS5713_DRC1_ATTACK_RELEASE_RATE 0x3C
-+#define TAS5713_DRC2_SOFTENING_FILTER_ALPHA_OMEGA 0x3E
-+#define TAS5713_DRC2_ATTACK_RELEASE_RATE 0x3F
-+#define TAS5713_DRC1_ATTACK_RELEASE_THRES 0x40
-+#define TAS5713_DRC2_ATTACK_RELEASE_THRES 0x43
-+#define TAS5713_DRC_CTRL 0x46
-+
-+#define TAS5713_BANK_SW_CTRL 0x50
-+#define TAS5713_CH1_OUTPUT_MIXER 0x51
-+#define TAS5713_CH2_OUTPUT_MIXER 0x52
-+#define TAS5713_CH1_INPUT_MIXER 0x53
-+#define TAS5713_CH2_INPUT_MIXER 0x54
-+#define TAS5713_OUTPUT_POST_SCALE 0x56
-+#define TAS5713_OUTPUT_PRESCALE 0x57
-+
-+#define TAS5713_IDF_POST_SCALE 0x62
-+
-+#define TAS5713_CH1_INLINE_MIXER 0x70
-+#define TAS5713_CH1_INLINE_DRC_EN_MIXER 0x71
-+#define TAS5713_CH1_R_CHANNEL_MIXER 0x72
-+#define TAS5713_CH1_L_CHANNEL_MIXER 0x73
-+#define TAS5713_CH2_INLINE_MIXER 0x74
-+#define TAS5713_CH2_INLINE_DRC_EN_MIXER 0x75
-+#define TAS5713_CH2_L_CHANNEL_MIXER 0x76
-+#define TAS5713_CH2_R_CHANNEL_MIXER 0x77
-+
-+#define TAS5713_UPDATE_DEV_ADDR_KEY 0xF8
-+#define TAS5713_UPDATE_DEV_ADDR_REG 0xF9
-+
-+#define TAS5713_REGISTER_COUNT 0x46
-+#define TAS5713_MAX_REGISTER 0xF9
-+
-+
-+// Bitmasks for registers
-+#define TAS5713_SOFT_MUTE_ALL 0x07
-+
-+
-+
-+struct tas5713_init_command {
-+ const int size;
-+ const char *const data;
-+};
-+
-+static const struct tas5713_init_command tas5713_init_sequence[] = {
-+
-+ // Trim oscillator
-+ { .size = 2, .data = "\x1B\x00" },
-+ // System control register 1 (0x03): block DC
-+ { .size = 2, .data = "\x03\x80" },
-+ // Mute everything
-+ { .size = 2, .data = "\x05\x40" },
-+ // Modulation limit register (0x10): 97.7%
-+ { .size = 2, .data = "\x10\x02" },
-+ // Interchannel delay registers
-+ // (0x11, 0x12, 0x13, and 0x14): BD mode
-+ { .size = 2, .data = "\x11\xB8" },
-+ { .size = 2, .data = "\x12\x60" },
-+ { .size = 2, .data = "\x13\xA0" },
-+ { .size = 2, .data = "\x14\x48" },
-+ // PWM shutdown group register (0x19): no shutdown
-+ { .size = 2, .data = "\x19\x00" },
-+ // Input multiplexer register (0x20): BD mode
-+ { .size = 2, .data = "\x20\x00\x89\x77\x72" },
-+ // PWM output mux register (0x25)
-+ // Channel 1 --> OUTA, channel 1 neg --> OUTB
-+ // Channel 2 --> OUTC, channel 2 neg --> OUTD
-+ { .size = 5, .data = "\x25\x01\x02\x13\x45" },
-+ // DRC control (0x46): DRC off
-+ { .size = 5, .data = "\x46\x00\x00\x00\x00" },
-+ // BKND_ERR register (0x1C): 299ms reset period
-+ { .size = 2, .data = "\x1C\x07" },
-+ // Mute channel 3
-+ { .size = 2, .data = "\x0A\xFF" },
-+ // Volume configuration register (0x0E): volume slew 512 steps
-+ { .size = 2, .data = "\x0E\x90" },
-+ // Clock control register (0x00): 44/48kHz, MCLK=64xfs
-+ { .size = 2, .data = "\x00\x60" },
-+ // Bank switch and eq control (0x50): no bank switching
-+ { .size = 5, .data = "\x50\x00\x00\x00\x00" },
-+ // Volume registers (0x07, 0x08, 0x09, 0x0A)
-+ { .size = 2, .data = "\x07\x20" },
-+ { .size = 2, .data = "\x08\x30" },
-+ { .size = 2, .data = "\x09\x30" },
-+ { .size = 2, .data = "\x0A\xFF" },
-+ // 0x72, 0x73, 0x76, 0x77 input mixer:
-+ // no intermix between channels
-+ { .size = 5, .data = "\x72\x00\x00\x00\x00" },
-+ { .size = 5, .data = "\x73\x00\x80\x00\x00" },
-+ { .size = 5, .data = "\x76\x00\x00\x00\x00" },
-+ { .size = 5, .data = "\x77\x00\x80\x00\x00" },
-+ // 0x70, 0x71, 0x74, 0x75 inline DRC mixer:
-+ // no inline DRC inmix
-+ { .size = 5, .data = "\x70\x00\x80\x00\x00" },
-+ { .size = 5, .data = "\x71\x00\x00\x00\x00" },
-+ { .size = 5, .data = "\x74\x00\x80\x00\x00" },
-+ { .size = 5, .data = "\x75\x00\x00\x00\x00" },
-+ // 0x56, 0x57 Output scale
-+ { .size = 5, .data = "\x56\x00\x80\x00\x00" },
-+ { .size = 5, .data = "\x57\x00\x02\x00\x00" },
-+ // 0x3B, 0x3c
-+ { .size = 9, .data = "\x3B\x00\x08\x00\x00\x00\x78\x00\x00" },
-+ { .size = 9, .data = "\x3C\x00\x00\x01\x00\xFF\xFF\xFF\x00" },
-+ { .size = 9, .data = "\x3E\x00\x08\x00\x00\x00\x78\x00\x00" },
-+ { .size = 9, .data = "\x3F\x00\x00\x01\x00\xFF\xFF\xFF\x00" },
-+ { .size = 9, .data = "\x40\x00\x00\x01\x00\xFF\xFF\xFF\x00" },
-+ { .size = 9, .data = "\x43\x00\x00\x01\x00\xFF\xFF\xFF\x00" },
-+ // 0x51, 0x52: output mixer
-+ { .size = 9, .data = "\x51\x00\x80\x00\x00\x00\x00\x00\x00" },
-+ { .size = 9, .data = "\x52\x00\x80\x00\x00\x00\x00\x00\x00" },
-+ // PEQ defaults
-+ { .size = 21, .data = "\x29\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" },
-+ { .size = 21, .data = "\x2A\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" },
-+ { .size = 21, .data = "\x2B\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" },
-+ { .size = 21, .data = "\x2C\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" },
-+ { .size = 21, .data = "\x2D\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" },
-+ { .size = 21, .data = "\x2E\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" },
-+ { .size = 21, .data = "\x2F\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" },
-+ { .size = 21, .data = "\x30\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" },
-+ { .size = 21, .data = "\x31\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" },
-+ { .size = 21, .data = "\x32\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" },
-+ { .size = 21, .data = "\x33\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" },
-+ { .size = 21, .data = "\x34\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" },
-+ { .size = 21, .data = "\x35\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" },
-+ { .size = 21, .data = "\x36\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" },
-+ { .size = 21, .data = "\x58\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" },
-+ { .size = 21, .data = "\x59\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" },
-+ { .size = 21, .data = "\x5C\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" },
-+ { .size = 21, .data = "\x5D\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" },
-+ { .size = 21, .data = "\x5E\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" },
-+ { .size = 21, .data = "\x5F\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" },
-+ { .size = 21, .data = "\x5A\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" },
-+ { .size = 21, .data = "\x5B\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" },
-+};
-+
-+
-+#endif /* _TAS5713_H */
diff --git a/target/linux/brcm2708/patches-4.4/0072-Update-ds1307-driver-for-device-tree-support.patch b/target/linux/brcm2708/patches-4.4/0072-Update-ds1307-driver-for-device-tree-support.patch
deleted file mode 100644
index 8095d93..0000000
--- a/target/linux/brcm2708/patches-4.4/0072-Update-ds1307-driver-for-device-tree-support.patch
+++ /dev/null
@@ -1,27 +0,0 @@
-From b2f628e980ca6ee05ec6dde093b31e40e67d9f9e Mon Sep 17 00:00:00 2001
-From: Ryan Coe <bluemrp9 at gmail.com>
-Date: Sat, 31 Jan 2015 18:25:49 -0700
-Subject: [PATCH] Update ds1307 driver for device-tree support
-
-Signed-off-by: Ryan Coe <bluemrp9 at gmail.com>
----
- drivers/rtc/rtc-ds1307.c | 8 ++++++++
- 1 file changed, 8 insertions(+)
-
---- a/drivers/rtc/rtc-ds1307.c
-+++ b/drivers/rtc/rtc-ds1307.c
-@@ -1207,6 +1207,14 @@ static int ds1307_remove(struct i2c_clie
- return 0;
- }
-
-+#ifdef CONFIG_OF
-+static const struct of_device_id ds1307_of_match[] = {
-+ { .compatible = "maxim,ds1307" },
-+ { }
-+};
-+MODULE_DEVICE_TABLE(of, ds1307_of_match);
-+#endif
-+
- static struct i2c_driver ds1307_driver = {
- .driver = {
- .name = "rtc-ds1307",
diff --git a/target/linux/brcm2708/patches-4.4/0073-BCM270x_DT-Add-pwr_led-and-the-required-input-trigge.patch b/target/linux/brcm2708/patches-4.4/0073-BCM270x_DT-Add-pwr_led-and-the-required-input-trigge.patch
deleted file mode 100644
index 0e57d3c..0000000
--- a/target/linux/brcm2708/patches-4.4/0073-BCM270x_DT-Add-pwr_led-and-the-required-input-trigge.patch
+++ /dev/null
@@ -1,169 +0,0 @@
-From 7f8f07caeaaf136c786e07a6d088f10a1ec59791 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 6 Feb 2015 13:50:57 +0000
-Subject: [PATCH] BCM270x_DT: Add pwr_led, and the required "input" trigger
-
-The "input" trigger makes the associated GPIO an input. This is to support
-the Raspberry Pi PWR LED, which is driven by external hardware in normal use.
-
-N.B. pwr_led is not available on Model A or B boards.
-
-leds-gpio: Implement the brightness_get method
-
-The power LED uses some clever logic that means it is driven
-by a voltage measuring circuit when configured as input, otherwise
-it is driven by the GPIO output value. This patch wires up the
-brightness_get method for leds-gpio so that user-space can monitor
-the LED value via /sys/class/gpio/led1/brightness. Using the input
-trigger this returns an indication of the system power health,
-otherwise it is just whatever value the trigger has written most
-recently.
-
-See: https://github.com/raspberrypi/linux/issues/1064
----
- drivers/leds/leds-gpio.c | 18 +++++++++++-
- drivers/leds/trigger/Kconfig | 7 +++++
- drivers/leds/trigger/Makefile | 1 +
- drivers/leds/trigger/ledtrig-input.c | 54 ++++++++++++++++++++++++++++++++++++
- include/linux/leds.h | 3 ++
- 5 files changed, 82 insertions(+), 1 deletion(-)
- create mode 100644 drivers/leds/trigger/ledtrig-input.c
-
---- a/drivers/leds/leds-gpio.c
-+++ b/drivers/leds/leds-gpio.c
-@@ -42,6 +42,13 @@ static void gpio_led_work(struct work_st
- led_dat->platform_gpio_blink_set(led_dat->gpiod,
- led_dat->new_level, NULL, NULL);
- led_dat->blinking = 0;
-+ } else if (led_dat->cdev.flags & SET_GPIO_INPUT) {
-+ gpiod_direction_input(led_dat->gpiod);
-+ led_dat->cdev.flags &= ~SET_GPIO_INPUT;
-+ }
-+ else if (led_dat->cdev.flags & SET_GPIO_OUTPUT) {
-+ gpiod_direction_output(led_dat->gpiod, led_dat->new_level);
-+ led_dat->cdev.flags &= ~SET_GPIO_OUTPUT;
- } else
- gpiod_set_value_cansleep(led_dat->gpiod, led_dat->new_level);
- }
-@@ -62,7 +69,8 @@ static void gpio_led_set(struct led_clas
- * seem to have a reliable way to know if we're already in one; so
- * let's just assume the worst.
- */
-- if (led_dat->can_sleep) {
-+ if (led_dat->can_sleep ||
-+ (led_dat->cdev.flags & (SET_GPIO_INPUT | SET_GPIO_OUTPUT) )) {
- led_dat->new_level = level;
- schedule_work(&led_dat->work);
- } else {
-@@ -75,6 +83,13 @@ static void gpio_led_set(struct led_clas
- }
- }
-
-+static enum led_brightness gpio_led_get(struct led_classdev *led_cdev)
-+{
-+ struct gpio_led_data *led_dat =
-+ container_of(led_cdev, struct gpio_led_data, cdev);
-+ return gpiod_get_value_cansleep(led_dat->gpiod) ? LED_FULL : LED_OFF;
-+}
-+
- static int gpio_blink_set(struct led_classdev *led_cdev,
- unsigned long *delay_on, unsigned long *delay_off)
- {
-@@ -131,6 +146,7 @@ static int create_gpio_led(const struct
- led_dat->cdev.blink_set = gpio_blink_set;
- }
- led_dat->cdev.brightness_set = gpio_led_set;
-+ led_dat->cdev.brightness_get = gpio_led_get;
- if (template->default_state == LEDS_GPIO_DEFSTATE_KEEP)
- state = !!gpiod_get_value_cansleep(led_dat->gpiod);
- else
---- a/drivers/leds/trigger/Kconfig
-+++ b/drivers/leds/trigger/Kconfig
-@@ -115,4 +115,11 @@ config LEDS_TRIGGER_NETDEV
- This allows LEDs to be controlled by network device activity.
- If unsure, say Y.
-
-+config LEDS_TRIGGER_INPUT
-+ tristate "LED Input Trigger"
-+ depends on LEDS_TRIGGERS
-+ help
-+ This allows the GPIOs assigned to be LEDs to be initialised to inputs.
-+ If unsure, say Y.
-+
- endif # LEDS_TRIGGERS
---- a/drivers/leds/trigger/Makefile
-+++ b/drivers/leds/trigger/Makefile
-@@ -8,3 +8,4 @@ obj-$(CONFIG_LEDS_TRIGGER_CPU) += ledtr
- obj-$(CONFIG_LEDS_TRIGGER_DEFAULT_ON) += ledtrig-default-on.o
- obj-$(CONFIG_LEDS_TRIGGER_TRANSIENT) += ledtrig-transient.o
- obj-$(CONFIG_LEDS_TRIGGER_CAMERA) += ledtrig-camera.o
-+obj-$(CONFIG_LEDS_TRIGGER_INPUT) += ledtrig-input.o
---- /dev/null
-+++ b/drivers/leds/trigger/ledtrig-input.c
-@@ -0,0 +1,54 @@
-+/*
-+ * Set LED GPIO to Input "Trigger"
-+ *
-+ * Copyright 2015 Phil Elwell <phil at raspberrypi.org>
-+ *
-+ * Based on Nick Forbes's ledtrig-default-on.c.
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ *
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/kernel.h>
-+#include <linux/init.h>
-+#include <linux/leds.h>
-+#include <linux/gpio.h>
-+#include "../leds.h"
-+
-+static void input_trig_activate(struct led_classdev *led_cdev)
-+{
-+ led_cdev->flags |= SET_GPIO_INPUT;
-+ led_set_brightness_async(led_cdev, 0);
-+}
-+
-+static void input_trig_deactivate(struct led_classdev *led_cdev)
-+{
-+ led_cdev->flags |= SET_GPIO_OUTPUT;
-+ led_set_brightness_async(led_cdev, 0);
-+}
-+
-+static struct led_trigger input_led_trigger = {
-+ .name = "input",
-+ .activate = input_trig_activate,
-+ .deactivate = input_trig_deactivate,
-+};
-+
-+static int __init input_trig_init(void)
-+{
-+ return led_trigger_register(&input_led_trigger);
-+}
-+
-+static void __exit input_trig_exit(void)
-+{
-+ led_trigger_unregister(&input_led_trigger);
-+}
-+
-+module_init(input_trig_init);
-+module_exit(input_trig_exit);
-+
-+MODULE_AUTHOR("Phil Elwell <phil at raspberrypi.org>");
-+MODULE_DESCRIPTION("Set LED GPIO to Input \"trigger\"");
-+MODULE_LICENSE("GPL");
---- a/include/linux/leds.h
-+++ b/include/linux/leds.h
-@@ -48,6 +48,9 @@ struct led_classdev {
- #define SET_BRIGHTNESS_ASYNC (1 << 21)
- #define SET_BRIGHTNESS_SYNC (1 << 22)
- #define LED_DEV_CAP_FLASH (1 << 23)
-+ /* Additions for Raspberry Pi PWR LED */
-+#define SET_GPIO_INPUT (1 << 30)
-+#define SET_GPIO_OUTPUT (1 << 31)
-
- /* Set LED brightness level */
- /* Must not sleep, use a workqueue if needed */
diff --git a/target/linux/brcm2708/patches-4.4/0074-enc28j60-Add-device-tree-compatible-string-and-an-ov.patch b/target/linux/brcm2708/patches-4.4/0074-enc28j60-Add-device-tree-compatible-string-and-an-ov.patch
deleted file mode 100644
index b0f511e..0000000
--- a/target/linux/brcm2708/patches-4.4/0074-enc28j60-Add-device-tree-compatible-string-and-an-ov.patch
+++ /dev/null
@@ -1,28 +0,0 @@
-From eb20da3dea76bd4835582038015ddfee2c401ee7 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 27 Feb 2015 15:10:24 +0000
-Subject: [PATCH] enc28j60: Add device tree compatible string and an overlay
-
----
- drivers/net/ethernet/microchip/enc28j60.c | 7 +++++++
- 1 file changed, 7 insertions(+)
-
---- a/drivers/net/ethernet/microchip/enc28j60.c
-+++ b/drivers/net/ethernet/microchip/enc28j60.c
-@@ -1630,9 +1630,16 @@ static int enc28j60_remove(struct spi_de
- return 0;
- }
-
-+static const struct of_device_id enc28j60_of_match[] = {
-+ { .compatible = "microchip,enc28j60", },
-+ { /* sentinel */ }
-+};
-+MODULE_DEVICE_TABLE(of, enc28j60_of_match);
-+
- static struct spi_driver enc28j60_driver = {
- .driver = {
- .name = DRV_NAME,
-+ .of_match_table = enc28j60_of_match,
- },
- .probe = enc28j60_probe,
- .remove = enc28j60_remove,
diff --git a/target/linux/brcm2708/patches-4.4/0075-Add-driver-for-rpi-proto.patch b/target/linux/brcm2708/patches-4.4/0075-Add-driver-for-rpi-proto.patch
deleted file mode 100644
index 63ce5c2..0000000
--- a/target/linux/brcm2708/patches-4.4/0075-Add-driver-for-rpi-proto.patch
+++ /dev/null
@@ -1,210 +0,0 @@
-From 6860141990edff57afd01f0d73d13cc7e84dd570 Mon Sep 17 00:00:00 2001
-From: Waldemar Brodkorb <wbrodkorb at conet.de>
-Date: Wed, 25 Mar 2015 09:26:17 +0100
-Subject: [PATCH] Add driver for rpi-proto
-
-Forward port of 3.10.x driver from https://github.com/koalo
-We are using a custom board and would like to use rpi 3.18.x
-kernel. Patch works fine for our embedded system.
-
-URL to the audio chip:
-http://www.mikroe.com/add-on-boards/audio-voice/audio-codec-proto/
-
-Playback tested with devicetree enabled.
-
-Signed-off-by: Waldemar Brodkorb <wbrodkorb at conet.de>
----
- sound/soc/bcm/Kconfig | 7 +++
- sound/soc/bcm/Makefile | 2 +
- sound/soc/bcm/rpi-proto.c | 153 ++++++++++++++++++++++++++++++++++++++++++++++
- 3 files changed, 162 insertions(+)
- create mode 100644 sound/soc/bcm/rpi-proto.c
-
---- a/sound/soc/bcm/Kconfig
-+++ b/sound/soc/bcm/Kconfig
-@@ -43,6 +43,13 @@ config SND_BCM2708_SOC_RPI_DAC
- help
- Say Y or M if you want to add support for RPi-DAC.
-
-+config SND_BCM2708_SOC_RPI_PROTO
-+ tristate "Support for Rpi-PROTO"
-+ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
-+ select SND_SOC_WM8731
-+ help
-+ Say Y or M if you want to add support for Audio Codec Board PROTO (WM8731).
-+
- config SND_BCM2708_SOC_IQAUDIO_DAC
- tristate "Support for IQaudIO-DAC"
- depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
---- a/sound/soc/bcm/Makefile
-+++ b/sound/soc/bcm/Makefile
-@@ -9,6 +9,7 @@ snd-soc-hifiberry-dacplus-objs := hifibe
- snd-soc-hifiberry-digi-objs := hifiberry_digi.o
- snd-soc-hifiberry-amp-objs := hifiberry_amp.o
- snd-soc-rpi-dac-objs := rpi-dac.o
-+snd-soc-rpi-proto-objs := rpi-proto.o
- snd-soc-iqaudio-dac-objs := iqaudio-dac.o
-
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DAC) += snd-soc-hifiberry-dac.o
-@@ -16,4 +17,5 @@ obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_D
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DIGI) += snd-soc-hifiberry-digi.o
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_AMP) += snd-soc-hifiberry-amp.o
- obj-$(CONFIG_SND_BCM2708_SOC_RPI_DAC) += snd-soc-rpi-dac.o
-+obj-$(CONFIG_SND_BCM2708_SOC_RPI_PROTO) += snd-soc-rpi-proto.o
- obj-$(CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC) += snd-soc-iqaudio-dac.o
---- /dev/null
-+++ b/sound/soc/bcm/rpi-proto.c
-@@ -0,0 +1,153 @@
-+/*
-+ * ASoC driver for PROTO AudioCODEC (with a WM8731)
-+ * connected to a Raspberry Pi
-+ *
-+ * Author: Florian Meier, <koalo at koalo.de>
-+ * Copyright 2013
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+
-+#include <sound/core.h>
-+#include <sound/pcm.h>
-+#include <sound/soc.h>
-+#include <sound/jack.h>
-+
-+#include "../codecs/wm8731.h"
-+
-+static const unsigned int wm8731_rates_12288000[] = {
-+ 8000, 32000, 48000, 96000,
-+};
-+
-+static struct snd_pcm_hw_constraint_list wm8731_constraints_12288000 = {
-+ .list = wm8731_rates_12288000,
-+ .count = ARRAY_SIZE(wm8731_rates_12288000),
-+};
-+
-+static int snd_rpi_proto_startup(struct snd_pcm_substream *substream)
-+{
-+ /* Setup constraints, because there is a 12.288 MHz XTAL on the board */
-+ snd_pcm_hw_constraint_list(substream->runtime, 0,
-+ SNDRV_PCM_HW_PARAM_RATE,
-+ &wm8731_constraints_12288000);
-+ return 0;
-+}
-+
-+static int snd_rpi_proto_hw_params(struct snd_pcm_substream *substream,
-+ struct snd_pcm_hw_params *params)
-+{
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_codec *codec = rtd->codec;
-+ struct snd_soc_dai *codec_dai = rtd->codec_dai;
-+ struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
-+ int sysclk = 12288000; /* This is fixed on this board */
-+
-+ /* Set proto bclk */
-+ int ret = snd_soc_dai_set_bclk_ratio(cpu_dai,32*2);
-+ if (ret < 0){
-+ dev_err(codec->dev,
-+ "Failed to set BCLK ratio %d\n", ret);
-+ return ret;
-+ }
-+
-+ /* Set proto sysclk */
-+ ret = snd_soc_dai_set_sysclk(codec_dai, WM8731_SYSCLK_XTAL,
-+ sysclk, SND_SOC_CLOCK_IN);
-+ if (ret < 0) {
-+ dev_err(codec->dev,
-+ "Failed to set WM8731 SYSCLK: %d\n", ret);
-+ return ret;
-+ }
-+
-+ return 0;
-+}
-+
-+/* machine stream operations */
-+static struct snd_soc_ops snd_rpi_proto_ops = {
-+ .startup = snd_rpi_proto_startup,
-+ .hw_params = snd_rpi_proto_hw_params,
-+};
-+
-+static struct snd_soc_dai_link snd_rpi_proto_dai[] = {
-+{
-+ .name = "WM8731",
-+ .stream_name = "WM8731 HiFi",
-+ .cpu_dai_name = "bcm2708-i2s.0",
-+ .codec_dai_name = "wm8731-hifi",
-+ .platform_name = "bcm2708-i2s.0",
-+ .codec_name = "wm8731.1-001a",
-+ .dai_fmt = SND_SOC_DAIFMT_I2S
-+ | SND_SOC_DAIFMT_NB_NF
-+ | SND_SOC_DAIFMT_CBM_CFM,
-+ .ops = &snd_rpi_proto_ops,
-+},
-+};
-+
-+/* audio machine driver */
-+static struct snd_soc_card snd_rpi_proto = {
-+ .name = "snd_rpi_proto",
-+ .dai_link = snd_rpi_proto_dai,
-+ .num_links = ARRAY_SIZE(snd_rpi_proto_dai),
-+};
-+
-+static int snd_rpi_proto_probe(struct platform_device *pdev)
-+{
-+ int ret = 0;
-+
-+ snd_rpi_proto.dev = &pdev->dev;
-+
-+ if (pdev->dev.of_node) {
-+ struct device_node *i2s_node;
-+ struct snd_soc_dai_link *dai = &snd_rpi_proto_dai[0];
-+ i2s_node = of_parse_phandle(pdev->dev.of_node,
-+ "i2s-controller", 0);
-+
-+ if (i2s_node) {
-+ dai->cpu_dai_name = NULL;
-+ dai->cpu_of_node = i2s_node;
-+ dai->platform_name = NULL;
-+ dai->platform_of_node = i2s_node;
-+ }
-+ }
-+
-+ ret = snd_soc_register_card(&snd_rpi_proto);
-+ if (ret) {
-+ dev_err(&pdev->dev,
-+ "snd_soc_register_card() failed: %d\n", ret);
-+ }
-+
-+ return ret;
-+}
-+
-+
-+static int snd_rpi_proto_remove(struct platform_device *pdev)
-+{
-+ return snd_soc_unregister_card(&snd_rpi_proto);
-+}
-+
-+static const struct of_device_id snd_rpi_proto_of_match[] = {
-+ { .compatible = "rpi,rpi-proto", },
-+ {},
-+};
-+MODULE_DEVICE_TABLE(of, snd_rpi_proto_of_match);
-+
-+static struct platform_driver snd_rpi_proto_driver = {
-+ .driver = {
-+ .name = "snd-rpi-proto",
-+ .owner = THIS_MODULE,
-+ .of_match_table = snd_rpi_proto_of_match,
-+ },
-+ .probe = snd_rpi_proto_probe,
-+ .remove = snd_rpi_proto_remove,
-+};
-+
-+module_platform_driver(snd_rpi_proto_driver);
-+
-+MODULE_AUTHOR("Florian Meier");
-+MODULE_DESCRIPTION("ASoC Driver for Raspberry Pi connected to PROTO board (WM8731)");
-+MODULE_LICENSE("GPL");
diff --git a/target/linux/brcm2708/patches-4.4/0076-config-Add-default-configs.patch b/target/linux/brcm2708/patches-4.4/0076-config-Add-default-configs.patch
deleted file mode 100644
index d8220bf..0000000
--- a/target/linux/brcm2708/patches-4.4/0076-config-Add-default-configs.patch
+++ /dev/null
@@ -1,2537 +0,0 @@
-From 5b9683226032a237e057ed5f3241d8c2bda3d708 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Mon, 13 Apr 2015 17:16:29 +0100
-Subject: [PATCH] config: Add default configs
-
----
- arch/arm/configs/bcm2709_defconfig | 1254 +++++++++++++++++++++++++++++++++++
- arch/arm/configs/bcmrpi_defconfig | 1265 ++++++++++++++++++++++++++++++++++++
- 2 files changed, 2519 insertions(+)
- create mode 100644 arch/arm/configs/bcm2709_defconfig
- create mode 100644 arch/arm/configs/bcmrpi_defconfig
-
---- /dev/null
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -0,0 +1,1254 @@
-+# CONFIG_ARM_PATCH_PHYS_VIRT is not set
-+CONFIG_PHYS_OFFSET=0
-+CONFIG_LOCALVERSION="-v7"
-+# CONFIG_LOCALVERSION_AUTO is not set
-+CONFIG_SYSVIPC=y
-+CONFIG_POSIX_MQUEUE=y
-+CONFIG_FHANDLE=y
-+CONFIG_NO_HZ=y
-+CONFIG_HIGH_RES_TIMERS=y
-+CONFIG_BSD_PROCESS_ACCT=y
-+CONFIG_BSD_PROCESS_ACCT_V3=y
-+CONFIG_TASKSTATS=y
-+CONFIG_TASK_DELAY_ACCT=y
-+CONFIG_TASK_XACCT=y
-+CONFIG_TASK_IO_ACCOUNTING=y
-+CONFIG_IKCONFIG=m
-+CONFIG_IKCONFIG_PROC=y
-+CONFIG_CGROUP_FREEZER=y
-+CONFIG_CGROUP_DEVICE=y
-+CONFIG_CPUSETS=y
-+CONFIG_CGROUP_CPUACCT=y
-+CONFIG_MEMCG=y
-+CONFIG_BLK_CGROUP=y
-+CONFIG_NAMESPACES=y
-+CONFIG_SCHED_AUTOGROUP=y
-+CONFIG_BLK_DEV_INITRD=y
-+CONFIG_EMBEDDED=y
-+# CONFIG_COMPAT_BRK is not set
-+CONFIG_PROFILING=y
-+CONFIG_OPROFILE=m
-+CONFIG_KPROBES=y
-+CONFIG_JUMP_LABEL=y
-+CONFIG_MODULES=y
-+CONFIG_MODULE_UNLOAD=y
-+CONFIG_MODVERSIONS=y
-+CONFIG_MODULE_SRCVERSION_ALL=y
-+CONFIG_BLK_DEV_THROTTLING=y
-+CONFIG_PARTITION_ADVANCED=y
-+CONFIG_MAC_PARTITION=y
-+CONFIG_CFQ_GROUP_IOSCHED=y
-+CONFIG_ARCH_BCM2709=y
-+# CONFIG_CACHE_L2X0 is not set
-+CONFIG_SMP=y
-+CONFIG_HAVE_ARM_ARCH_TIMER=y
-+CONFIG_VMSPLIT_2G=y
-+CONFIG_PREEMPT_VOLUNTARY=y
-+CONFIG_AEABI=y
-+CONFIG_OABI_COMPAT=y
-+# CONFIG_CPU_SW_DOMAIN_PAN is not set
-+CONFIG_CLEANCACHE=y
-+CONFIG_FRONTSWAP=y
-+CONFIG_CMA=y
-+CONFIG_ZSMALLOC=m
-+CONFIG_PGTABLE_MAPPING=y
-+CONFIG_UACCESS_WITH_MEMCPY=y
-+CONFIG_SECCOMP=y
-+# CONFIG_ATAGS is not set
-+CONFIG_ZBOOT_ROM_TEXT=0x0
-+CONFIG_ZBOOT_ROM_BSS=0x0
-+CONFIG_CMDLINE="console=ttyAMA0,115200 kgdboc=ttyAMA0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 rootwait"
-+CONFIG_CPU_FREQ=y
-+CONFIG_CPU_FREQ_STAT=m
-+CONFIG_CPU_FREQ_STAT_DETAILS=y
-+CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE=y
-+CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
-+CONFIG_CPU_FREQ_GOV_USERSPACE=y
-+CONFIG_CPU_FREQ_GOV_ONDEMAND=y
-+CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
-+CONFIG_VFP=y
-+CONFIG_NEON=y
-+CONFIG_KERNEL_MODE_NEON=y
-+CONFIG_BINFMT_MISC=m
-+# CONFIG_SUSPEND is not set
-+CONFIG_NET=y
-+CONFIG_PACKET=y
-+CONFIG_UNIX=y
-+CONFIG_XFRM_USER=y
-+CONFIG_NET_KEY=m
-+CONFIG_INET=y
-+CONFIG_IP_MULTICAST=y
-+CONFIG_IP_ADVANCED_ROUTER=y
-+CONFIG_IP_MULTIPLE_TABLES=y
-+CONFIG_IP_ROUTE_MULTIPATH=y
-+CONFIG_IP_ROUTE_VERBOSE=y
-+CONFIG_IP_PNP=y
-+CONFIG_IP_PNP_DHCP=y
-+CONFIG_IP_PNP_RARP=y
-+CONFIG_NET_IPIP=m
-+CONFIG_NET_IPGRE_DEMUX=m
-+CONFIG_NET_IPGRE=m
-+CONFIG_IP_MROUTE=y
-+CONFIG_IP_MROUTE_MULTIPLE_TABLES=y
-+CONFIG_IP_PIMSM_V1=y
-+CONFIG_IP_PIMSM_V2=y
-+CONFIG_SYN_COOKIES=y
-+CONFIG_INET_AH=m
-+CONFIG_INET_ESP=m
-+CONFIG_INET_IPCOMP=m
-+CONFIG_INET_XFRM_MODE_TRANSPORT=m
-+CONFIG_INET_XFRM_MODE_TUNNEL=m
-+CONFIG_INET_XFRM_MODE_BEET=m
-+CONFIG_INET_LRO=m
-+CONFIG_INET_DIAG=m
-+CONFIG_INET6_AH=m
-+CONFIG_INET6_ESP=m
-+CONFIG_INET6_IPCOMP=m
-+CONFIG_IPV6_TUNNEL=m
-+CONFIG_IPV6_MULTIPLE_TABLES=y
-+CONFIG_IPV6_MROUTE=y
-+CONFIG_IPV6_MROUTE_MULTIPLE_TABLES=y
-+CONFIG_IPV6_PIMSM_V2=y
-+CONFIG_NETFILTER=y
-+CONFIG_NF_CONNTRACK=m
-+CONFIG_NF_CONNTRACK_ZONES=y
-+CONFIG_NF_CONNTRACK_EVENTS=y
-+CONFIG_NF_CONNTRACK_TIMESTAMP=y
-+CONFIG_NF_CT_PROTO_DCCP=m
-+CONFIG_NF_CT_PROTO_UDPLITE=m
-+CONFIG_NF_CONNTRACK_AMANDA=m
-+CONFIG_NF_CONNTRACK_FTP=m
-+CONFIG_NF_CONNTRACK_H323=m
-+CONFIG_NF_CONNTRACK_IRC=m
-+CONFIG_NF_CONNTRACK_NETBIOS_NS=m
-+CONFIG_NF_CONNTRACK_SNMP=m
-+CONFIG_NF_CONNTRACK_PPTP=m
-+CONFIG_NF_CONNTRACK_SANE=m
-+CONFIG_NF_CONNTRACK_SIP=m
-+CONFIG_NF_CONNTRACK_TFTP=m
-+CONFIG_NF_CT_NETLINK=m
-+CONFIG_NETFILTER_XT_SET=m
-+CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
-+CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
-+CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
-+CONFIG_NETFILTER_XT_TARGET_DSCP=m
-+CONFIG_NETFILTER_XT_TARGET_HMARK=m
-+CONFIG_NETFILTER_XT_TARGET_IDLETIMER=m
-+CONFIG_NETFILTER_XT_TARGET_LED=m
-+CONFIG_NETFILTER_XT_TARGET_LOG=m
-+CONFIG_NETFILTER_XT_TARGET_MARK=m
-+CONFIG_NETFILTER_XT_TARGET_NFLOG=m
-+CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
-+CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
-+CONFIG_NETFILTER_XT_TARGET_TEE=m
-+CONFIG_NETFILTER_XT_TARGET_TPROXY=m
-+CONFIG_NETFILTER_XT_TARGET_TRACE=m
-+CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
-+CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
-+CONFIG_NETFILTER_XT_MATCH_ADDRTYPE=m
-+CONFIG_NETFILTER_XT_MATCH_BPF=m
-+CONFIG_NETFILTER_XT_MATCH_CLUSTER=m
-+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
-+CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
-+CONFIG_NETFILTER_XT_MATCH_CONNLABEL=m
-+CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
-+CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
-+CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
-+CONFIG_NETFILTER_XT_MATCH_CPU=m
-+CONFIG_NETFILTER_XT_MATCH_DCCP=m
-+CONFIG_NETFILTER_XT_MATCH_DEVGROUP=m
-+CONFIG_NETFILTER_XT_MATCH_DSCP=m
-+CONFIG_NETFILTER_XT_MATCH_ESP=m
-+CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
-+CONFIG_NETFILTER_XT_MATCH_HELPER=m
-+CONFIG_NETFILTER_XT_MATCH_IPRANGE=m
-+CONFIG_NETFILTER_XT_MATCH_IPVS=m
-+CONFIG_NETFILTER_XT_MATCH_LENGTH=m
-+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
-+CONFIG_NETFILTER_XT_MATCH_MAC=m
-+CONFIG_NETFILTER_XT_MATCH_MARK=m
-+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
-+CONFIG_NETFILTER_XT_MATCH_NFACCT=m
-+CONFIG_NETFILTER_XT_MATCH_OSF=m
-+CONFIG_NETFILTER_XT_MATCH_OWNER=m
-+CONFIG_NETFILTER_XT_MATCH_POLICY=m
-+CONFIG_NETFILTER_XT_MATCH_PHYSDEV=m
-+CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
-+CONFIG_NETFILTER_XT_MATCH_QUOTA=m
-+CONFIG_NETFILTER_XT_MATCH_RATEEST=m
-+CONFIG_NETFILTER_XT_MATCH_REALM=m
-+CONFIG_NETFILTER_XT_MATCH_RECENT=m
-+CONFIG_NETFILTER_XT_MATCH_SOCKET=m
-+CONFIG_NETFILTER_XT_MATCH_STATE=m
-+CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
-+CONFIG_NETFILTER_XT_MATCH_STRING=m
-+CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
-+CONFIG_NETFILTER_XT_MATCH_TIME=m
-+CONFIG_NETFILTER_XT_MATCH_U32=m
-+CONFIG_IP_SET=m
-+CONFIG_IP_SET_BITMAP_IP=m
-+CONFIG_IP_SET_BITMAP_IPMAC=m
-+CONFIG_IP_SET_BITMAP_PORT=m
-+CONFIG_IP_SET_HASH_IP=m
-+CONFIG_IP_SET_HASH_IPPORT=m
-+CONFIG_IP_SET_HASH_IPPORTIP=m
-+CONFIG_IP_SET_HASH_IPPORTNET=m
-+CONFIG_IP_SET_HASH_NET=m
-+CONFIG_IP_SET_HASH_NETPORT=m
-+CONFIG_IP_SET_HASH_NETIFACE=m
-+CONFIG_IP_SET_LIST_SET=m
-+CONFIG_IP_VS=m
-+CONFIG_IP_VS_PROTO_TCP=y
-+CONFIG_IP_VS_PROTO_UDP=y
-+CONFIG_IP_VS_PROTO_ESP=y
-+CONFIG_IP_VS_PROTO_AH=y
-+CONFIG_IP_VS_PROTO_SCTP=y
-+CONFIG_IP_VS_RR=m
-+CONFIG_IP_VS_WRR=m
-+CONFIG_IP_VS_LC=m
-+CONFIG_IP_VS_WLC=m
-+CONFIG_IP_VS_LBLC=m
-+CONFIG_IP_VS_LBLCR=m
-+CONFIG_IP_VS_DH=m
-+CONFIG_IP_VS_SH=m
-+CONFIG_IP_VS_SED=m
-+CONFIG_IP_VS_NQ=m
-+CONFIG_IP_VS_FTP=m
-+CONFIG_IP_VS_PE_SIP=m
-+CONFIG_NF_CONNTRACK_IPV4=m
-+CONFIG_IP_NF_IPTABLES=m
-+CONFIG_IP_NF_MATCH_AH=m
-+CONFIG_IP_NF_MATCH_ECN=m
-+CONFIG_IP_NF_MATCH_TTL=m
-+CONFIG_IP_NF_FILTER=m
-+CONFIG_IP_NF_TARGET_REJECT=m
-+CONFIG_IP_NF_NAT=m
-+CONFIG_IP_NF_TARGET_MASQUERADE=m
-+CONFIG_IP_NF_TARGET_NETMAP=m
-+CONFIG_IP_NF_TARGET_REDIRECT=m
-+CONFIG_IP_NF_MANGLE=m
-+CONFIG_IP_NF_TARGET_CLUSTERIP=m
-+CONFIG_IP_NF_TARGET_ECN=m
-+CONFIG_IP_NF_TARGET_TTL=m
-+CONFIG_IP_NF_RAW=m
-+CONFIG_IP_NF_ARPTABLES=m
-+CONFIG_IP_NF_ARPFILTER=m
-+CONFIG_IP_NF_ARP_MANGLE=m
-+CONFIG_NF_CONNTRACK_IPV6=m
-+CONFIG_IP6_NF_IPTABLES=m
-+CONFIG_IP6_NF_MATCH_AH=m
-+CONFIG_IP6_NF_MATCH_EUI64=m
-+CONFIG_IP6_NF_MATCH_FRAG=m
-+CONFIG_IP6_NF_MATCH_OPTS=m
-+CONFIG_IP6_NF_MATCH_HL=m
-+CONFIG_IP6_NF_MATCH_IPV6HEADER=m
-+CONFIG_IP6_NF_MATCH_MH=m
-+CONFIG_IP6_NF_MATCH_RT=m
-+CONFIG_IP6_NF_TARGET_HL=m
-+CONFIG_IP6_NF_FILTER=m
-+CONFIG_IP6_NF_TARGET_REJECT=m
-+CONFIG_IP6_NF_MANGLE=m
-+CONFIG_IP6_NF_RAW=m
-+CONFIG_IP6_NF_NAT=m
-+CONFIG_IP6_NF_TARGET_MASQUERADE=m
-+CONFIG_IP6_NF_TARGET_NPT=m
-+CONFIG_BRIDGE_NF_EBTABLES=m
-+CONFIG_BRIDGE_EBT_BROUTE=m
-+CONFIG_BRIDGE_EBT_T_FILTER=m
-+CONFIG_BRIDGE_EBT_T_NAT=m
-+CONFIG_BRIDGE_EBT_802_3=m
-+CONFIG_BRIDGE_EBT_AMONG=m
-+CONFIG_BRIDGE_EBT_ARP=m
-+CONFIG_BRIDGE_EBT_IP=m
-+CONFIG_BRIDGE_EBT_IP6=m
-+CONFIG_BRIDGE_EBT_LIMIT=m
-+CONFIG_BRIDGE_EBT_MARK=m
-+CONFIG_BRIDGE_EBT_PKTTYPE=m
-+CONFIG_BRIDGE_EBT_STP=m
-+CONFIG_BRIDGE_EBT_VLAN=m
-+CONFIG_BRIDGE_EBT_ARPREPLY=m
-+CONFIG_BRIDGE_EBT_DNAT=m
-+CONFIG_BRIDGE_EBT_MARK_T=m
-+CONFIG_BRIDGE_EBT_REDIRECT=m
-+CONFIG_BRIDGE_EBT_SNAT=m
-+CONFIG_BRIDGE_EBT_LOG=m
-+CONFIG_BRIDGE_EBT_NFLOG=m
-+CONFIG_SCTP_COOKIE_HMAC_SHA1=y
-+CONFIG_ATM=m
-+CONFIG_L2TP=m
-+CONFIG_L2TP_V3=y
-+CONFIG_L2TP_IP=m
-+CONFIG_L2TP_ETH=m
-+CONFIG_BRIDGE=m
-+CONFIG_VLAN_8021Q=m
-+CONFIG_VLAN_8021Q_GVRP=y
-+CONFIG_ATALK=m
-+CONFIG_6LOWPAN=m
-+CONFIG_IEEE802154=m
-+CONFIG_IEEE802154_6LOWPAN=m
-+CONFIG_MAC802154=m
-+CONFIG_NET_SCHED=y
-+CONFIG_NET_SCH_CBQ=m
-+CONFIG_NET_SCH_HTB=m
-+CONFIG_NET_SCH_HFSC=m
-+CONFIG_NET_SCH_PRIO=m
-+CONFIG_NET_SCH_MULTIQ=m
-+CONFIG_NET_SCH_RED=m
-+CONFIG_NET_SCH_SFB=m
-+CONFIG_NET_SCH_SFQ=m
-+CONFIG_NET_SCH_TEQL=m
-+CONFIG_NET_SCH_TBF=m
-+CONFIG_NET_SCH_GRED=m
-+CONFIG_NET_SCH_DSMARK=m
-+CONFIG_NET_SCH_NETEM=m
-+CONFIG_NET_SCH_DRR=m
-+CONFIG_NET_SCH_MQPRIO=m
-+CONFIG_NET_SCH_CHOKE=m
-+CONFIG_NET_SCH_QFQ=m
-+CONFIG_NET_SCH_CODEL=m
-+CONFIG_NET_SCH_FQ_CODEL=m
-+CONFIG_NET_SCH_INGRESS=m
-+CONFIG_NET_SCH_PLUG=m
-+CONFIG_NET_CLS_BASIC=m
-+CONFIG_NET_CLS_TCINDEX=m
-+CONFIG_NET_CLS_ROUTE4=m
-+CONFIG_NET_CLS_FW=m
-+CONFIG_NET_CLS_U32=m
-+CONFIG_CLS_U32_MARK=y
-+CONFIG_NET_CLS_RSVP=m
-+CONFIG_NET_CLS_RSVP6=m
-+CONFIG_NET_CLS_FLOW=m
-+CONFIG_NET_CLS_CGROUP=m
-+CONFIG_NET_EMATCH=y
-+CONFIG_NET_EMATCH_CMP=m
-+CONFIG_NET_EMATCH_NBYTE=m
-+CONFIG_NET_EMATCH_U32=m
-+CONFIG_NET_EMATCH_META=m
-+CONFIG_NET_EMATCH_TEXT=m
-+CONFIG_NET_EMATCH_IPSET=m
-+CONFIG_NET_CLS_ACT=y
-+CONFIG_NET_ACT_POLICE=m
-+CONFIG_NET_ACT_GACT=m
-+CONFIG_GACT_PROB=y
-+CONFIG_NET_ACT_MIRRED=m
-+CONFIG_NET_ACT_IPT=m
-+CONFIG_NET_ACT_NAT=m
-+CONFIG_NET_ACT_PEDIT=m
-+CONFIG_NET_ACT_SIMP=m
-+CONFIG_NET_ACT_SKBEDIT=m
-+CONFIG_NET_ACT_CSUM=m
-+CONFIG_BATMAN_ADV=m
-+CONFIG_OPENVSWITCH=m
-+CONFIG_NET_PKTGEN=m
-+CONFIG_HAMRADIO=y
-+CONFIG_AX25=m
-+CONFIG_NETROM=m
-+CONFIG_ROSE=m
-+CONFIG_MKISS=m
-+CONFIG_6PACK=m
-+CONFIG_BPQETHER=m
-+CONFIG_BAYCOM_SER_FDX=m
-+CONFIG_BAYCOM_SER_HDX=m
-+CONFIG_YAM=m
-+CONFIG_CAN=m
-+CONFIG_CAN_VCAN=m
-+CONFIG_CAN_MCP251X=m
-+CONFIG_IRDA=m
-+CONFIG_IRLAN=m
-+CONFIG_IRNET=m
-+CONFIG_IRCOMM=m
-+CONFIG_IRDA_ULTRA=y
-+CONFIG_IRDA_CACHE_LAST_LSAP=y
-+CONFIG_IRDA_FAST_RR=y
-+CONFIG_IRTTY_SIR=m
-+CONFIG_KINGSUN_DONGLE=m
-+CONFIG_KSDAZZLE_DONGLE=m
-+CONFIG_KS959_DONGLE=m
-+CONFIG_USB_IRDA=m
-+CONFIG_SIGMATEL_FIR=m
-+CONFIG_MCS_FIR=m
-+CONFIG_BT=m
-+CONFIG_BT_RFCOMM=m
-+CONFIG_BT_RFCOMM_TTY=y
-+CONFIG_BT_BNEP=m
-+CONFIG_BT_BNEP_MC_FILTER=y
-+CONFIG_BT_BNEP_PROTO_FILTER=y
-+CONFIG_BT_HIDP=m
-+CONFIG_BT_6LOWPAN=m
-+CONFIG_BT_HCIBTUSB=m
-+CONFIG_BT_HCIBCM203X=m
-+CONFIG_BT_HCIBPA10X=m
-+CONFIG_BT_HCIBFUSB=m
-+CONFIG_BT_HCIVHCI=m
-+CONFIG_BT_MRVL=m
-+CONFIG_BT_MRVL_SDIO=m
-+CONFIG_BT_ATH3K=m
-+CONFIG_BT_WILINK=m
-+CONFIG_MAC80211=m
-+CONFIG_MAC80211_MESH=y
-+CONFIG_WIMAX=m
-+CONFIG_RFKILL=m
-+CONFIG_RFKILL_INPUT=y
-+CONFIG_NET_9P=m
-+CONFIG_NFC=m
-+CONFIG_NFC_PN533=m
-+CONFIG_DEVTMPFS=y
-+CONFIG_DEVTMPFS_MOUNT=y
-+CONFIG_DMA_CMA=y
-+CONFIG_CMA_SIZE_MBYTES=5
-+CONFIG_MTD=m
-+CONFIG_MTD_BLOCK=m
-+CONFIG_MTD_NAND=m
-+CONFIG_MTD_UBI=m
-+CONFIG_ZRAM=m
-+CONFIG_ZRAM_LZ4_COMPRESS=y
-+CONFIG_BLK_DEV_LOOP=y
-+CONFIG_BLK_DEV_CRYPTOLOOP=m
-+CONFIG_BLK_DEV_DRBD=m
-+CONFIG_BLK_DEV_NBD=m
-+CONFIG_BLK_DEV_RAM=y
-+CONFIG_CDROM_PKTCDVD=m
-+CONFIG_ATA_OVER_ETH=m
-+CONFIG_EEPROM_AT24=m
-+CONFIG_TI_ST=m
-+CONFIG_SCSI=y
-+# CONFIG_SCSI_PROC_FS is not set
-+CONFIG_BLK_DEV_SD=y
-+CONFIG_CHR_DEV_ST=m
-+CONFIG_CHR_DEV_OSST=m
-+CONFIG_BLK_DEV_SR=m
-+CONFIG_CHR_DEV_SG=m
-+CONFIG_SCSI_ISCSI_ATTRS=y
-+CONFIG_ISCSI_TCP=m
-+CONFIG_ISCSI_BOOT_SYSFS=m
-+CONFIG_MD=y
-+CONFIG_MD_LINEAR=m
-+CONFIG_MD_RAID0=m
-+CONFIG_BLK_DEV_DM=m
-+CONFIG_DM_CRYPT=m
-+CONFIG_DM_SNAPSHOT=m
-+CONFIG_DM_THIN_PROVISIONING=m
-+CONFIG_DM_MIRROR=m
-+CONFIG_DM_LOG_USERSPACE=m
-+CONFIG_DM_RAID=m
-+CONFIG_DM_ZERO=m
-+CONFIG_DM_DELAY=m
-+CONFIG_NETDEVICES=y
-+CONFIG_BONDING=m
-+CONFIG_DUMMY=m
-+CONFIG_IFB=m
-+CONFIG_MACVLAN=m
-+CONFIG_NETCONSOLE=m
-+CONFIG_TUN=m
-+CONFIG_VETH=m
-+CONFIG_ENC28J60=m
-+CONFIG_MDIO_BITBANG=m
-+CONFIG_PPP=m
-+CONFIG_PPP_BSDCOMP=m
-+CONFIG_PPP_DEFLATE=m
-+CONFIG_PPP_FILTER=y
-+CONFIG_PPP_MPPE=m
-+CONFIG_PPP_MULTILINK=y
-+CONFIG_PPPOATM=m
-+CONFIG_PPPOE=m
-+CONFIG_PPPOL2TP=m
-+CONFIG_PPP_ASYNC=m
-+CONFIG_PPP_SYNC_TTY=m
-+CONFIG_SLIP=m
-+CONFIG_SLIP_COMPRESSED=y
-+CONFIG_SLIP_SMART=y
-+CONFIG_USB_CATC=m
-+CONFIG_USB_KAWETH=m
-+CONFIG_USB_PEGASUS=m
-+CONFIG_USB_RTL8150=m
-+CONFIG_USB_RTL8152=m
-+CONFIG_USB_USBNET=y
-+CONFIG_USB_NET_AX8817X=m
-+CONFIG_USB_NET_AX88179_178A=m
-+CONFIG_USB_NET_CDCETHER=m
-+CONFIG_USB_NET_CDC_EEM=m
-+CONFIG_USB_NET_CDC_NCM=m
-+CONFIG_USB_NET_HUAWEI_CDC_NCM=m
-+CONFIG_USB_NET_CDC_MBIM=m
-+CONFIG_USB_NET_DM9601=m
-+CONFIG_USB_NET_SR9700=m
-+CONFIG_USB_NET_SR9800=m
-+CONFIG_USB_NET_SMSC75XX=m
-+CONFIG_USB_NET_SMSC95XX=y
-+CONFIG_USB_NET_GL620A=m
-+CONFIG_USB_NET_NET1080=m
-+CONFIG_USB_NET_PLUSB=m
-+CONFIG_USB_NET_MCS7830=m
-+CONFIG_USB_NET_CDC_SUBSET=m
-+CONFIG_USB_ALI_M5632=y
-+CONFIG_USB_AN2720=y
-+CONFIG_USB_EPSON2888=y
-+CONFIG_USB_KC2190=y
-+CONFIG_USB_NET_ZAURUS=m
-+CONFIG_USB_NET_CX82310_ETH=m
-+CONFIG_USB_NET_KALMIA=m
-+CONFIG_USB_NET_QMI_WWAN=m
-+CONFIG_USB_HSO=m
-+CONFIG_USB_NET_INT51X1=m
-+CONFIG_USB_IPHETH=m
-+CONFIG_USB_SIERRA_NET=m
-+CONFIG_USB_VL600=m
-+CONFIG_LIBERTAS_THINFIRM=m
-+CONFIG_LIBERTAS_THINFIRM_USB=m
-+CONFIG_AT76C50X_USB=m
-+CONFIG_USB_ZD1201=m
-+CONFIG_USB_NET_RNDIS_WLAN=m
-+CONFIG_RTL8187=m
-+CONFIG_MAC80211_HWSIM=m
-+CONFIG_ATH_CARDS=m
-+CONFIG_ATH9K=m
-+CONFIG_ATH9K_HTC=m
-+CONFIG_CARL9170=m
-+CONFIG_ATH6KL=m
-+CONFIG_ATH6KL_USB=m
-+CONFIG_AR5523=m
-+CONFIG_B43=m
-+# CONFIG_B43_PHY_N is not set
-+CONFIG_B43LEGACY=m
-+CONFIG_BRCMFMAC=m
-+CONFIG_BRCMFMAC_USB=y
-+CONFIG_HOSTAP=m
-+CONFIG_LIBERTAS=m
-+CONFIG_LIBERTAS_USB=m
-+CONFIG_LIBERTAS_SDIO=m
-+CONFIG_P54_COMMON=m
-+CONFIG_P54_USB=m
-+CONFIG_RT2X00=m
-+CONFIG_RT2500USB=m
-+CONFIG_RT73USB=m
-+CONFIG_RT2800USB=m
-+CONFIG_RT2800USB_RT3573=y
-+CONFIG_RT2800USB_RT53XX=y
-+CONFIG_RT2800USB_RT55XX=y
-+CONFIG_RT2800USB_UNKNOWN=y
-+CONFIG_WL_MEDIATEK=y
-+CONFIG_MT7601U=m
-+CONFIG_RTL8192CU=m
-+CONFIG_ZD1211RW=m
-+CONFIG_MWIFIEX=m
-+CONFIG_MWIFIEX_SDIO=m
-+CONFIG_WIMAX_I2400M_USB=m
-+CONFIG_IEEE802154_AT86RF230=m
-+CONFIG_IEEE802154_MRF24J40=m
-+CONFIG_IEEE802154_CC2520=m
-+CONFIG_INPUT_POLLDEV=m
-+# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-+CONFIG_INPUT_JOYDEV=m
-+CONFIG_INPUT_EVDEV=m
-+# CONFIG_KEYBOARD_ATKBD is not set
-+CONFIG_KEYBOARD_GPIO=m
-+# CONFIG_INPUT_MOUSE is not set
-+CONFIG_INPUT_JOYSTICK=y
-+CONFIG_JOYSTICK_IFORCE=m
-+CONFIG_JOYSTICK_IFORCE_USB=y
-+CONFIG_JOYSTICK_XPAD=m
-+CONFIG_JOYSTICK_XPAD_FF=y
-+CONFIG_JOYSTICK_RPISENSE=m
-+CONFIG_INPUT_TOUCHSCREEN=y
-+CONFIG_TOUCHSCREEN_ADS7846=m
-+CONFIG_TOUCHSCREEN_EGALAX=m
-+CONFIG_TOUCHSCREEN_FT6236=m
-+CONFIG_TOUCHSCREEN_RPI_FT5406=m
-+CONFIG_TOUCHSCREEN_USB_COMPOSITE=m
-+CONFIG_TOUCHSCREEN_STMPE=m
-+CONFIG_INPUT_MISC=y
-+CONFIG_INPUT_AD714X=m
-+CONFIG_INPUT_ATI_REMOTE2=m
-+CONFIG_INPUT_KEYSPAN_REMOTE=m
-+CONFIG_INPUT_POWERMATE=m
-+CONFIG_INPUT_YEALINK=m
-+CONFIG_INPUT_CM109=m
-+CONFIG_INPUT_UINPUT=m
-+CONFIG_INPUT_GPIO_ROTARY_ENCODER=m
-+CONFIG_INPUT_ADXL34X=m
-+CONFIG_INPUT_CMA3000=m
-+CONFIG_SERIO=m
-+CONFIG_SERIO_RAW=m
-+CONFIG_GAMEPORT=m
-+CONFIG_GAMEPORT_NS558=m
-+CONFIG_GAMEPORT_L4=m
-+CONFIG_BRCM_CHAR_DRIVERS=y
-+CONFIG_BCM_VC_CMA=y
-+CONFIG_BCM_VCIO=y
-+CONFIG_BCM_VC_SM=y
-+CONFIG_DEVPTS_MULTIPLE_INSTANCES=y
-+# CONFIG_LEGACY_PTYS is not set
-+# CONFIG_DEVKMEM is not set
-+CONFIG_SERIAL_8250=y
-+# CONFIG_SERIAL_8250_DEPRECATED_OPTIONS is not set
-+CONFIG_SERIAL_8250_CONSOLE=y
-+# CONFIG_SERIAL_8250_DMA is not set
-+CONFIG_SERIAL_8250_NR_UARTS=1
-+CONFIG_SERIAL_8250_RUNTIME_UARTS=0
-+CONFIG_SERIAL_AMBA_PL011=y
-+CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
-+CONFIG_SERIAL_OF_PLATFORM=y
-+CONFIG_TTY_PRINTK=y
-+CONFIG_HW_RANDOM=y
-+CONFIG_HW_RANDOM_BCM2835=y
-+CONFIG_RAW_DRIVER=y
-+CONFIG_I2C=y
-+CONFIG_I2C_CHARDEV=m
-+CONFIG_I2C_BCM2708=m
-+CONFIG_SPI=y
-+CONFIG_SPI_BCM2835=m
-+CONFIG_SPI_SPIDEV=y
-+CONFIG_PPS=m
-+CONFIG_PPS_CLIENT_LDISC=m
-+CONFIG_PPS_CLIENT_GPIO=m
-+CONFIG_GPIO_SYSFS=y
-+CONFIG_GPIO_ARIZONA=m
-+CONFIG_GPIO_STMPE=y
-+CONFIG_W1=m
-+CONFIG_W1_MASTER_DS2490=m
-+CONFIG_W1_MASTER_DS2482=m
-+CONFIG_W1_MASTER_DS1WM=m
-+CONFIG_W1_MASTER_GPIO=m
-+CONFIG_W1_SLAVE_THERM=m
-+CONFIG_W1_SLAVE_SMEM=m
-+CONFIG_W1_SLAVE_DS2408=m
-+CONFIG_W1_SLAVE_DS2413=m
-+CONFIG_W1_SLAVE_DS2406=m
-+CONFIG_W1_SLAVE_DS2423=m
-+CONFIG_W1_SLAVE_DS2431=m
-+CONFIG_W1_SLAVE_DS2433=m
-+CONFIG_W1_SLAVE_DS2760=m
-+CONFIG_W1_SLAVE_DS2780=m
-+CONFIG_W1_SLAVE_DS2781=m
-+CONFIG_W1_SLAVE_DS28E04=m
-+CONFIG_W1_SLAVE_BQ27000=m
-+CONFIG_BATTERY_DS2760=m
-+CONFIG_POWER_RESET=y
-+CONFIG_POWER_RESET_GPIO=y
-+CONFIG_HWMON=m
-+CONFIG_SENSORS_SHT21=m
-+CONFIG_SENSORS_SHTC1=m
-+CONFIG_THERMAL=y
-+CONFIG_THERMAL_BCM2835=y
-+CONFIG_WATCHDOG=y
-+CONFIG_BCM2835_WDT=m
-+CONFIG_UCB1400_CORE=m
-+CONFIG_MFD_STMPE=y
-+CONFIG_STMPE_SPI=y
-+CONFIG_MFD_ARIZONA_I2C=m
-+CONFIG_MFD_ARIZONA_SPI=m
-+CONFIG_MFD_WM5102=y
-+CONFIG_MEDIA_SUPPORT=m
-+CONFIG_MEDIA_CAMERA_SUPPORT=y
-+CONFIG_MEDIA_ANALOG_TV_SUPPORT=y
-+CONFIG_MEDIA_DIGITAL_TV_SUPPORT=y
-+CONFIG_MEDIA_RADIO_SUPPORT=y
-+CONFIG_MEDIA_RC_SUPPORT=y
-+CONFIG_MEDIA_CONTROLLER=y
-+CONFIG_LIRC=m
-+CONFIG_RC_DEVICES=y
-+CONFIG_RC_ATI_REMOTE=m
-+CONFIG_IR_IMON=m
-+CONFIG_IR_MCEUSB=m
-+CONFIG_IR_REDRAT3=m
-+CONFIG_IR_STREAMZAP=m
-+CONFIG_IR_IGUANA=m
-+CONFIG_IR_TTUSBIR=m
-+CONFIG_RC_LOOPBACK=m
-+CONFIG_IR_GPIO_CIR=m
-+CONFIG_MEDIA_USB_SUPPORT=y
-+CONFIG_USB_VIDEO_CLASS=m
-+CONFIG_USB_M5602=m
-+CONFIG_USB_STV06XX=m
-+CONFIG_USB_GL860=m
-+CONFIG_USB_GSPCA_BENQ=m
-+CONFIG_USB_GSPCA_CONEX=m
-+CONFIG_USB_GSPCA_CPIA1=m
-+CONFIG_USB_GSPCA_DTCS033=m
-+CONFIG_USB_GSPCA_ETOMS=m
-+CONFIG_USB_GSPCA_FINEPIX=m
-+CONFIG_USB_GSPCA_JEILINJ=m
-+CONFIG_USB_GSPCA_JL2005BCD=m
-+CONFIG_USB_GSPCA_KINECT=m
-+CONFIG_USB_GSPCA_KONICA=m
-+CONFIG_USB_GSPCA_MARS=m
-+CONFIG_USB_GSPCA_MR97310A=m
-+CONFIG_USB_GSPCA_NW80X=m
-+CONFIG_USB_GSPCA_OV519=m
-+CONFIG_USB_GSPCA_OV534=m
-+CONFIG_USB_GSPCA_OV534_9=m
-+CONFIG_USB_GSPCA_PAC207=m
-+CONFIG_USB_GSPCA_PAC7302=m
-+CONFIG_USB_GSPCA_PAC7311=m
-+CONFIG_USB_GSPCA_SE401=m
-+CONFIG_USB_GSPCA_SN9C2028=m
-+CONFIG_USB_GSPCA_SN9C20X=m
-+CONFIG_USB_GSPCA_SONIXB=m
-+CONFIG_USB_GSPCA_SONIXJ=m
-+CONFIG_USB_GSPCA_SPCA500=m
-+CONFIG_USB_GSPCA_SPCA501=m
-+CONFIG_USB_GSPCA_SPCA505=m
-+CONFIG_USB_GSPCA_SPCA506=m
-+CONFIG_USB_GSPCA_SPCA508=m
-+CONFIG_USB_GSPCA_SPCA561=m
-+CONFIG_USB_GSPCA_SPCA1528=m
-+CONFIG_USB_GSPCA_SQ905=m
-+CONFIG_USB_GSPCA_SQ905C=m
-+CONFIG_USB_GSPCA_SQ930X=m
-+CONFIG_USB_GSPCA_STK014=m
-+CONFIG_USB_GSPCA_STK1135=m
-+CONFIG_USB_GSPCA_STV0680=m
-+CONFIG_USB_GSPCA_SUNPLUS=m
-+CONFIG_USB_GSPCA_T613=m
-+CONFIG_USB_GSPCA_TOPRO=m
-+CONFIG_USB_GSPCA_TV8532=m
-+CONFIG_USB_GSPCA_VC032X=m
-+CONFIG_USB_GSPCA_VICAM=m
-+CONFIG_USB_GSPCA_XIRLINK_CIT=m
-+CONFIG_USB_GSPCA_ZC3XX=m
-+CONFIG_USB_PWC=m
-+CONFIG_VIDEO_CPIA2=m
-+CONFIG_USB_ZR364XX=m
-+CONFIG_USB_STKWEBCAM=m
-+CONFIG_USB_S2255=m
-+CONFIG_VIDEO_USBTV=m
-+CONFIG_VIDEO_PVRUSB2=m
-+CONFIG_VIDEO_HDPVR=m
-+CONFIG_VIDEO_USBVISION=m
-+CONFIG_VIDEO_STK1160_COMMON=m
-+CONFIG_VIDEO_STK1160_AC97=y
-+CONFIG_VIDEO_GO7007=m
-+CONFIG_VIDEO_GO7007_USB=m
-+CONFIG_VIDEO_GO7007_USB_S2250_BOARD=m
-+CONFIG_VIDEO_AU0828=m
-+CONFIG_VIDEO_AU0828_RC=y
-+CONFIG_VIDEO_CX231XX=m
-+CONFIG_VIDEO_CX231XX_ALSA=m
-+CONFIG_VIDEO_CX231XX_DVB=m
-+CONFIG_VIDEO_TM6000=m
-+CONFIG_VIDEO_TM6000_ALSA=m
-+CONFIG_VIDEO_TM6000_DVB=m
-+CONFIG_DVB_USB=m
-+CONFIG_DVB_USB_A800=m
-+CONFIG_DVB_USB_DIBUSB_MB=m
-+CONFIG_DVB_USB_DIBUSB_MB_FAULTY=y
-+CONFIG_DVB_USB_DIBUSB_MC=m
-+CONFIG_DVB_USB_DIB0700=m
-+CONFIG_DVB_USB_UMT_010=m
-+CONFIG_DVB_USB_CXUSB=m
-+CONFIG_DVB_USB_M920X=m
-+CONFIG_DVB_USB_DIGITV=m
-+CONFIG_DVB_USB_VP7045=m
-+CONFIG_DVB_USB_VP702X=m
-+CONFIG_DVB_USB_GP8PSK=m
-+CONFIG_DVB_USB_NOVA_T_USB2=m
-+CONFIG_DVB_USB_TTUSB2=m
-+CONFIG_DVB_USB_DTT200U=m
-+CONFIG_DVB_USB_OPERA1=m
-+CONFIG_DVB_USB_AF9005=m
-+CONFIG_DVB_USB_AF9005_REMOTE=m
-+CONFIG_DVB_USB_PCTV452E=m
-+CONFIG_DVB_USB_DW2102=m
-+CONFIG_DVB_USB_CINERGY_T2=m
-+CONFIG_DVB_USB_DTV5100=m
-+CONFIG_DVB_USB_FRIIO=m
-+CONFIG_DVB_USB_AZ6027=m
-+CONFIG_DVB_USB_TECHNISAT_USB2=m
-+CONFIG_DVB_USB_V2=m
-+CONFIG_DVB_USB_AF9015=m
-+CONFIG_DVB_USB_AF9035=m
-+CONFIG_DVB_USB_ANYSEE=m
-+CONFIG_DVB_USB_AU6610=m
-+CONFIG_DVB_USB_AZ6007=m
-+CONFIG_DVB_USB_CE6230=m
-+CONFIG_DVB_USB_EC168=m
-+CONFIG_DVB_USB_GL861=m
-+CONFIG_DVB_USB_LME2510=m
-+CONFIG_DVB_USB_MXL111SF=m
-+CONFIG_DVB_USB_RTL28XXU=m
-+CONFIG_DVB_USB_DVBSKY=m
-+CONFIG_SMS_USB_DRV=m
-+CONFIG_DVB_B2C2_FLEXCOP_USB=m
-+CONFIG_DVB_AS102=m
-+CONFIG_VIDEO_EM28XX=m
-+CONFIG_VIDEO_EM28XX_V4L2=m
-+CONFIG_VIDEO_EM28XX_ALSA=m
-+CONFIG_VIDEO_EM28XX_DVB=m
-+CONFIG_V4L_PLATFORM_DRIVERS=y
-+CONFIG_VIDEO_BCM2835=y
-+CONFIG_VIDEO_BCM2835_MMAL=m
-+CONFIG_RADIO_SI470X=y
-+CONFIG_USB_SI470X=m
-+CONFIG_I2C_SI470X=m
-+CONFIG_RADIO_SI4713=m
-+CONFIG_I2C_SI4713=m
-+CONFIG_USB_MR800=m
-+CONFIG_USB_DSBR=m
-+CONFIG_RADIO_SHARK=m
-+CONFIG_RADIO_SHARK2=m
-+CONFIG_USB_KEENE=m
-+CONFIG_USB_MA901=m
-+CONFIG_RADIO_TEA5764=m
-+CONFIG_RADIO_SAA7706H=m
-+CONFIG_RADIO_TEF6862=m
-+CONFIG_RADIO_WL1273=m
-+CONFIG_RADIO_WL128X=m
-+# CONFIG_MEDIA_SUBDRV_AUTOSELECT is not set
-+CONFIG_VIDEO_UDA1342=m
-+CONFIG_VIDEO_SONY_BTF_MPX=m
-+CONFIG_VIDEO_TVP5150=m
-+CONFIG_VIDEO_TW2804=m
-+CONFIG_VIDEO_TW9903=m
-+CONFIG_VIDEO_TW9906=m
-+CONFIG_VIDEO_OV7640=m
-+CONFIG_VIDEO_MT9V011=m
-+CONFIG_FB=y
-+CONFIG_FB_BCM2708=y
-+CONFIG_FB_UDL=m
-+CONFIG_FB_SSD1307=m
-+CONFIG_FB_RPISENSE=m
-+# CONFIG_BACKLIGHT_GENERIC is not set
-+CONFIG_BACKLIGHT_GPIO=m
-+CONFIG_FRAMEBUFFER_CONSOLE=y
-+CONFIG_LOGO=y
-+# CONFIG_LOGO_LINUX_MONO is not set
-+# CONFIG_LOGO_LINUX_VGA16 is not set
-+CONFIG_SOUND=y
-+CONFIG_SND=m
-+CONFIG_SND_SEQUENCER=m
-+CONFIG_SND_SEQ_DUMMY=m
-+CONFIG_SND_MIXER_OSS=m
-+CONFIG_SND_PCM_OSS=m
-+CONFIG_SND_SEQUENCER_OSS=y
-+CONFIG_SND_HRTIMER=m
-+CONFIG_SND_DUMMY=m
-+CONFIG_SND_ALOOP=m
-+CONFIG_SND_VIRMIDI=m
-+CONFIG_SND_MTPAV=m
-+CONFIG_SND_SERIAL_U16550=m
-+CONFIG_SND_MPU401=m
-+CONFIG_SND_BCM2835=m
-+CONFIG_SND_USB_AUDIO=m
-+CONFIG_SND_USB_UA101=m
-+CONFIG_SND_USB_CAIAQ=m
-+CONFIG_SND_USB_CAIAQ_INPUT=y
-+CONFIG_SND_USB_6FIRE=m
-+CONFIG_SND_SOC=m
-+CONFIG_SND_BCM2835_SOC_I2S=m
-+CONFIG_SND_BCM2708_SOC_HIFIBERRY_DAC=m
-+CONFIG_SND_BCM2708_SOC_HIFIBERRY_DACPLUS=m
-+CONFIG_SND_BCM2708_SOC_HIFIBERRY_DIGI=m
-+CONFIG_SND_BCM2708_SOC_HIFIBERRY_AMP=m
-+CONFIG_SND_BCM2708_SOC_RPI_DAC=m
-+CONFIG_SND_BCM2708_SOC_RPI_PROTO=m
-+CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC=m
-+CONFIG_SND_BCM2708_SOC_RASPIDAC3=m
-+CONFIG_SND_SOC_ADAU1701=m
-+CONFIG_SND_SOC_WM8804_I2C=m
-+CONFIG_SND_SIMPLE_CARD=m
-+CONFIG_SOUND_PRIME=m
-+CONFIG_HIDRAW=y
-+CONFIG_UHID=m
-+CONFIG_HID_A4TECH=m
-+CONFIG_HID_ACRUX=m
-+CONFIG_HID_APPLE=m
-+CONFIG_HID_BELKIN=m
-+CONFIG_HID_CHERRY=m
-+CONFIG_HID_CHICONY=m
-+CONFIG_HID_CYPRESS=m
-+CONFIG_HID_DRAGONRISE=m
-+CONFIG_HID_EMS_FF=m
-+CONFIG_HID_ELECOM=m
-+CONFIG_HID_ELO=m
-+CONFIG_HID_EZKEY=m
-+CONFIG_HID_HOLTEK=m
-+CONFIG_HID_KEYTOUCH=m
-+CONFIG_HID_KYE=m
-+CONFIG_HID_UCLOGIC=m
-+CONFIG_HID_WALTOP=m
-+CONFIG_HID_GYRATION=m
-+CONFIG_HID_TWINHAN=m
-+CONFIG_HID_KENSINGTON=m
-+CONFIG_HID_LCPOWER=m
-+CONFIG_HID_LOGITECH=m
-+CONFIG_HID_MAGICMOUSE=m
-+CONFIG_HID_MICROSOFT=m
-+CONFIG_HID_MONTEREY=m
-+CONFIG_HID_MULTITOUCH=m
-+CONFIG_HID_NTRIG=m
-+CONFIG_HID_ORTEK=m
-+CONFIG_HID_PANTHERLORD=m
-+CONFIG_HID_PETALYNX=m
-+CONFIG_HID_PICOLCD=m
-+CONFIG_HID_ROCCAT=m
-+CONFIG_HID_SAMSUNG=m
-+CONFIG_HID_SONY=m
-+CONFIG_HID_SPEEDLINK=m
-+CONFIG_HID_SUNPLUS=m
-+CONFIG_HID_GREENASIA=m
-+CONFIG_HID_SMARTJOYPLUS=m
-+CONFIG_HID_TOPSEED=m
-+CONFIG_HID_THINGM=m
-+CONFIG_HID_THRUSTMASTER=m
-+CONFIG_HID_WACOM=m
-+CONFIG_HID_WIIMOTE=m
-+CONFIG_HID_XINMO=m
-+CONFIG_HID_ZEROPLUS=m
-+CONFIG_HID_ZYDACRON=m
-+CONFIG_HID_PID=y
-+CONFIG_USB_HIDDEV=y
-+CONFIG_USB=y
-+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
-+CONFIG_USB_MON=m
-+CONFIG_USB_DWCOTG=y
-+CONFIG_USB_PRINTER=m
-+CONFIG_USB_STORAGE=y
-+CONFIG_USB_STORAGE_REALTEK=m
-+CONFIG_USB_STORAGE_DATAFAB=m
-+CONFIG_USB_STORAGE_FREECOM=m
-+CONFIG_USB_STORAGE_ISD200=m
-+CONFIG_USB_STORAGE_USBAT=m
-+CONFIG_USB_STORAGE_SDDR09=m
-+CONFIG_USB_STORAGE_SDDR55=m
-+CONFIG_USB_STORAGE_JUMPSHOT=m
-+CONFIG_USB_STORAGE_ALAUDA=m
-+CONFIG_USB_STORAGE_ONETOUCH=m
-+CONFIG_USB_STORAGE_KARMA=m
-+CONFIG_USB_STORAGE_CYPRESS_ATACB=m
-+CONFIG_USB_STORAGE_ENE_UB6250=m
-+CONFIG_USB_MDC800=m
-+CONFIG_USB_MICROTEK=m
-+CONFIG_USBIP_CORE=m
-+CONFIG_USBIP_VHCI_HCD=m
-+CONFIG_USBIP_HOST=m
-+CONFIG_USB_SERIAL=m
-+CONFIG_USB_SERIAL_GENERIC=y
-+CONFIG_USB_SERIAL_AIRCABLE=m
-+CONFIG_USB_SERIAL_ARK3116=m
-+CONFIG_USB_SERIAL_BELKIN=m
-+CONFIG_USB_SERIAL_CH341=m
-+CONFIG_USB_SERIAL_WHITEHEAT=m
-+CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
-+CONFIG_USB_SERIAL_CP210X=m
-+CONFIG_USB_SERIAL_CYPRESS_M8=m
-+CONFIG_USB_SERIAL_EMPEG=m
-+CONFIG_USB_SERIAL_FTDI_SIO=m
-+CONFIG_USB_SERIAL_VISOR=m
-+CONFIG_USB_SERIAL_IPAQ=m
-+CONFIG_USB_SERIAL_IR=m
-+CONFIG_USB_SERIAL_EDGEPORT=m
-+CONFIG_USB_SERIAL_EDGEPORT_TI=m
-+CONFIG_USB_SERIAL_F81232=m
-+CONFIG_USB_SERIAL_GARMIN=m
-+CONFIG_USB_SERIAL_IPW=m
-+CONFIG_USB_SERIAL_IUU=m
-+CONFIG_USB_SERIAL_KEYSPAN_PDA=m
-+CONFIG_USB_SERIAL_KEYSPAN=m
-+CONFIG_USB_SERIAL_KLSI=m
-+CONFIG_USB_SERIAL_KOBIL_SCT=m
-+CONFIG_USB_SERIAL_MCT_U232=m
-+CONFIG_USB_SERIAL_METRO=m
-+CONFIG_USB_SERIAL_MOS7720=m
-+CONFIG_USB_SERIAL_MOS7840=m
-+CONFIG_USB_SERIAL_NAVMAN=m
-+CONFIG_USB_SERIAL_PL2303=m
-+CONFIG_USB_SERIAL_OTI6858=m
-+CONFIG_USB_SERIAL_QCAUX=m
-+CONFIG_USB_SERIAL_QUALCOMM=m
-+CONFIG_USB_SERIAL_SPCP8X5=m
-+CONFIG_USB_SERIAL_SAFE=m
-+CONFIG_USB_SERIAL_SIERRAWIRELESS=m
-+CONFIG_USB_SERIAL_SYMBOL=m
-+CONFIG_USB_SERIAL_TI=m
-+CONFIG_USB_SERIAL_CYBERJACK=m
-+CONFIG_USB_SERIAL_XIRCOM=m
-+CONFIG_USB_SERIAL_OPTION=m
-+CONFIG_USB_SERIAL_OMNINET=m
-+CONFIG_USB_SERIAL_OPTICON=m
-+CONFIG_USB_SERIAL_XSENS_MT=m
-+CONFIG_USB_SERIAL_WISHBONE=m
-+CONFIG_USB_SERIAL_SSU100=m
-+CONFIG_USB_SERIAL_QT2=m
-+CONFIG_USB_SERIAL_DEBUG=m
-+CONFIG_USB_EMI62=m
-+CONFIG_USB_EMI26=m
-+CONFIG_USB_ADUTUX=m
-+CONFIG_USB_SEVSEG=m
-+CONFIG_USB_RIO500=m
-+CONFIG_USB_LEGOTOWER=m
-+CONFIG_USB_LCD=m
-+CONFIG_USB_LED=m
-+CONFIG_USB_CYPRESS_CY7C63=m
-+CONFIG_USB_CYTHERM=m
-+CONFIG_USB_IDMOUSE=m
-+CONFIG_USB_FTDI_ELAN=m
-+CONFIG_USB_APPLEDISPLAY=m
-+CONFIG_USB_LD=m
-+CONFIG_USB_TRANCEVIBRATOR=m
-+CONFIG_USB_IOWARRIOR=m
-+CONFIG_USB_TEST=m
-+CONFIG_USB_ISIGHTFW=m
-+CONFIG_USB_YUREX=m
-+CONFIG_USB_ATM=m
-+CONFIG_USB_SPEEDTOUCH=m
-+CONFIG_USB_CXACRU=m
-+CONFIG_USB_UEAGLEATM=m
-+CONFIG_USB_XUSBATM=m
-+CONFIG_MMC=y
-+CONFIG_MMC_BLOCK_MINORS=32
-+CONFIG_MMC_BCM2835=y
-+CONFIG_MMC_BCM2835_DMA=y
-+CONFIG_MMC_BCM2835_SDHOST=y
-+CONFIG_MMC_SDHCI=y
-+CONFIG_MMC_SDHCI_PLTFM=y
-+CONFIG_MMC_SPI=m
-+CONFIG_LEDS_CLASS=y
-+CONFIG_LEDS_GPIO=y
-+CONFIG_LEDS_TRIGGER_TIMER=y
-+CONFIG_LEDS_TRIGGER_ONESHOT=y
-+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
-+CONFIG_LEDS_TRIGGER_BACKLIGHT=y
-+CONFIG_LEDS_TRIGGER_CPU=y
-+CONFIG_LEDS_TRIGGER_GPIO=y
-+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
-+CONFIG_LEDS_TRIGGER_TRANSIENT=m
-+CONFIG_LEDS_TRIGGER_CAMERA=m
-+CONFIG_LEDS_TRIGGER_INPUT=y
-+CONFIG_RTC_CLASS=y
-+# CONFIG_RTC_HCTOSYS is not set
-+CONFIG_RTC_DRV_DS1307=m
-+CONFIG_RTC_DRV_DS1374=m
-+CONFIG_RTC_DRV_DS1672=m
-+CONFIG_RTC_DRV_DS3232=m
-+CONFIG_RTC_DRV_MAX6900=m
-+CONFIG_RTC_DRV_RS5C372=m
-+CONFIG_RTC_DRV_ISL1208=m
-+CONFIG_RTC_DRV_ISL12022=m
-+CONFIG_RTC_DRV_ISL12057=m
-+CONFIG_RTC_DRV_X1205=m
-+CONFIG_RTC_DRV_PCF2127=m
-+CONFIG_RTC_DRV_PCF8523=m
-+CONFIG_RTC_DRV_PCF8563=m
-+CONFIG_RTC_DRV_PCF8583=m
-+CONFIG_RTC_DRV_M41T80=m
-+CONFIG_RTC_DRV_BQ32K=m
-+CONFIG_RTC_DRV_S35390A=m
-+CONFIG_RTC_DRV_FM3130=m
-+CONFIG_RTC_DRV_RX8581=m
-+CONFIG_RTC_DRV_RX8025=m
-+CONFIG_RTC_DRV_EM3027=m
-+CONFIG_RTC_DRV_RV3029C2=m
-+CONFIG_RTC_DRV_M41T93=m
-+CONFIG_RTC_DRV_M41T94=m
-+CONFIG_RTC_DRV_DS1305=m
-+CONFIG_RTC_DRV_DS1390=m
-+CONFIG_RTC_DRV_MAX6902=m
-+CONFIG_RTC_DRV_R9701=m
-+CONFIG_RTC_DRV_RS5C348=m
-+CONFIG_RTC_DRV_DS3234=m
-+CONFIG_RTC_DRV_PCF2123=m
-+CONFIG_RTC_DRV_RX4581=m
-+CONFIG_DMADEVICES=y
-+CONFIG_DMA_BCM2835=y
-+CONFIG_DMA_BCM2708=y
-+CONFIG_UIO=m
-+CONFIG_UIO_PDRV_GENIRQ=m
-+CONFIG_STAGING=y
-+CONFIG_PRISM2_USB=m
-+CONFIG_R8712U=m
-+CONFIG_R8188EU=m
-+CONFIG_R8723AU=m
-+CONFIG_VT6656=m
-+CONFIG_SPEAKUP=m
-+CONFIG_SPEAKUP_SYNTH_SOFT=m
-+CONFIG_STAGING_MEDIA=y
-+CONFIG_LIRC_STAGING=y
-+CONFIG_LIRC_IMON=m
-+CONFIG_LIRC_RPI=m
-+CONFIG_LIRC_SASEM=m
-+CONFIG_LIRC_SERIAL=m
-+CONFIG_FB_TFT=m
-+CONFIG_FB_TFT_AGM1264K_FL=m
-+CONFIG_FB_TFT_BD663474=m
-+CONFIG_FB_TFT_HX8340BN=m
-+CONFIG_FB_TFT_HX8347D=m
-+CONFIG_FB_TFT_HX8353D=m
-+CONFIG_FB_TFT_ILI9163=m
-+CONFIG_FB_TFT_ILI9320=m
-+CONFIG_FB_TFT_ILI9325=m
-+CONFIG_FB_TFT_ILI9340=m
-+CONFIG_FB_TFT_ILI9341=m
-+CONFIG_FB_TFT_ILI9481=m
-+CONFIG_FB_TFT_ILI9486=m
-+CONFIG_FB_TFT_PCD8544=m
-+CONFIG_FB_TFT_RA8875=m
-+CONFIG_FB_TFT_S6D02A1=m
-+CONFIG_FB_TFT_S6D1121=m
-+CONFIG_FB_TFT_SSD1289=m
-+CONFIG_FB_TFT_SSD1306=m
-+CONFIG_FB_TFT_SSD1331=m
-+CONFIG_FB_TFT_SSD1351=m
-+CONFIG_FB_TFT_ST7735R=m
-+CONFIG_FB_TFT_TINYLCD=m
-+CONFIG_FB_TFT_TLS8204=m
-+CONFIG_FB_TFT_UC1701=m
-+CONFIG_FB_TFT_UPD161704=m
-+CONFIG_FB_TFT_WATTEROTT=m
-+CONFIG_FB_FLEX=m
-+CONFIG_FB_TFT_FBTFT_DEVICE=m
-+CONFIG_MAILBOX=y
-+CONFIG_BCM2835_MBOX=y
-+# CONFIG_IOMMU_SUPPORT is not set
-+CONFIG_EXTCON=m
-+CONFIG_EXTCON_ARIZONA=m
-+CONFIG_IIO=m
-+CONFIG_IIO_BUFFER=y
-+CONFIG_IIO_BUFFER_CB=y
-+CONFIG_IIO_KFIFO_BUF=m
-+CONFIG_MCP320X=m
-+CONFIG_DHT11=m
-+CONFIG_PWM_BCM2835=m
-+CONFIG_RASPBERRYPI_FIRMWARE=y
-+CONFIG_EXT4_FS=y
-+CONFIG_EXT4_FS_POSIX_ACL=y
-+CONFIG_EXT4_FS_SECURITY=y
-+CONFIG_REISERFS_FS=m
-+CONFIG_REISERFS_FS_XATTR=y
-+CONFIG_REISERFS_FS_POSIX_ACL=y
-+CONFIG_REISERFS_FS_SECURITY=y
-+CONFIG_JFS_FS=m
-+CONFIG_JFS_POSIX_ACL=y
-+CONFIG_JFS_SECURITY=y
-+CONFIG_JFS_STATISTICS=y
-+CONFIG_XFS_FS=m
-+CONFIG_XFS_QUOTA=y
-+CONFIG_XFS_POSIX_ACL=y
-+CONFIG_XFS_RT=y
-+CONFIG_GFS2_FS=m
-+CONFIG_OCFS2_FS=m
-+CONFIG_BTRFS_FS=m
-+CONFIG_BTRFS_FS_POSIX_ACL=y
-+CONFIG_NILFS2_FS=m
-+CONFIG_F2FS_FS=y
-+CONFIG_FANOTIFY=y
-+CONFIG_QFMT_V1=m
-+CONFIG_QFMT_V2=m
-+CONFIG_AUTOFS4_FS=y
-+CONFIG_FUSE_FS=m
-+CONFIG_CUSE=m
-+CONFIG_OVERLAY_FS=m
-+CONFIG_FSCACHE=y
-+CONFIG_FSCACHE_STATS=y
-+CONFIG_FSCACHE_HISTOGRAM=y
-+CONFIG_CACHEFILES=y
-+CONFIG_ISO9660_FS=m
-+CONFIG_JOLIET=y
-+CONFIG_ZISOFS=y
-+CONFIG_UDF_FS=m
-+CONFIG_MSDOS_FS=y
-+CONFIG_VFAT_FS=y
-+CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
-+CONFIG_NTFS_FS=m
-+CONFIG_NTFS_RW=y
-+CONFIG_TMPFS=y
-+CONFIG_TMPFS_POSIX_ACL=y
-+CONFIG_CONFIGFS_FS=y
-+CONFIG_ECRYPT_FS=m
-+CONFIG_HFS_FS=m
-+CONFIG_HFSPLUS_FS=m
-+CONFIG_JFFS2_FS=m
-+CONFIG_JFFS2_SUMMARY=y
-+CONFIG_UBIFS_FS=m
-+CONFIG_SQUASHFS=m
-+CONFIG_SQUASHFS_XATTR=y
-+CONFIG_SQUASHFS_LZO=y
-+CONFIG_SQUASHFS_XZ=y
-+CONFIG_NFS_FS=y
-+CONFIG_NFS_V3_ACL=y
-+CONFIG_NFS_V4=y
-+CONFIG_NFS_SWAP=y
-+CONFIG_ROOT_NFS=y
-+CONFIG_NFS_FSCACHE=y
-+CONFIG_NFSD=m
-+CONFIG_NFSD_V3_ACL=y
-+CONFIG_NFSD_V4=y
-+CONFIG_CIFS=m
-+CONFIG_CIFS_WEAK_PW_HASH=y
-+CONFIG_CIFS_UPCALL=y
-+CONFIG_CIFS_XATTR=y
-+CONFIG_CIFS_POSIX=y
-+CONFIG_CIFS_ACL=y
-+CONFIG_CIFS_DFS_UPCALL=y
-+CONFIG_CIFS_SMB2=y
-+CONFIG_CIFS_FSCACHE=y
-+CONFIG_9P_FS=m
-+CONFIG_9P_FS_POSIX_ACL=y
-+CONFIG_NLS_DEFAULT="utf8"
-+CONFIG_NLS_CODEPAGE_437=y
-+CONFIG_NLS_CODEPAGE_737=m
-+CONFIG_NLS_CODEPAGE_775=m
-+CONFIG_NLS_CODEPAGE_850=m
-+CONFIG_NLS_CODEPAGE_852=m
-+CONFIG_NLS_CODEPAGE_855=m
-+CONFIG_NLS_CODEPAGE_857=m
-+CONFIG_NLS_CODEPAGE_860=m
-+CONFIG_NLS_CODEPAGE_861=m
-+CONFIG_NLS_CODEPAGE_862=m
-+CONFIG_NLS_CODEPAGE_863=m
-+CONFIG_NLS_CODEPAGE_864=m
-+CONFIG_NLS_CODEPAGE_865=m
-+CONFIG_NLS_CODEPAGE_866=m
-+CONFIG_NLS_CODEPAGE_869=m
-+CONFIG_NLS_CODEPAGE_936=m
-+CONFIG_NLS_CODEPAGE_950=m
-+CONFIG_NLS_CODEPAGE_932=m
-+CONFIG_NLS_CODEPAGE_949=m
-+CONFIG_NLS_CODEPAGE_874=m
-+CONFIG_NLS_ISO8859_8=m
-+CONFIG_NLS_CODEPAGE_1250=m
-+CONFIG_NLS_CODEPAGE_1251=m
-+CONFIG_NLS_ASCII=y
-+CONFIG_NLS_ISO8859_1=m
-+CONFIG_NLS_ISO8859_2=m
-+CONFIG_NLS_ISO8859_3=m
-+CONFIG_NLS_ISO8859_4=m
-+CONFIG_NLS_ISO8859_5=m
-+CONFIG_NLS_ISO8859_6=m
-+CONFIG_NLS_ISO8859_7=m
-+CONFIG_NLS_ISO8859_9=m
-+CONFIG_NLS_ISO8859_13=m
-+CONFIG_NLS_ISO8859_14=m
-+CONFIG_NLS_ISO8859_15=m
-+CONFIG_NLS_KOI8_R=m
-+CONFIG_NLS_KOI8_U=m
-+CONFIG_DLM=m
-+CONFIG_PRINTK_TIME=y
-+CONFIG_BOOT_PRINTK_DELAY=y
-+CONFIG_DEBUG_MEMORY_INIT=y
-+CONFIG_DETECT_HUNG_TASK=y
-+CONFIG_TIMER_STATS=y
-+CONFIG_IRQSOFF_TRACER=y
-+CONFIG_SCHED_TRACER=y
-+CONFIG_STACK_TRACER=y
-+CONFIG_BLK_DEV_IO_TRACE=y
-+# CONFIG_KPROBE_EVENT is not set
-+CONFIG_FUNCTION_PROFILER=y
-+CONFIG_KGDB=y
-+CONFIG_KGDB_KDB=y
-+CONFIG_KDB_KEYBOARD=y
-+CONFIG_CRYPTO_USER=m
-+CONFIG_CRYPTO_CBC=y
-+CONFIG_CRYPTO_CTS=m
-+CONFIG_CRYPTO_XTS=m
-+CONFIG_CRYPTO_XCBC=m
-+CONFIG_CRYPTO_TGR192=m
-+CONFIG_CRYPTO_WP512=m
-+CONFIG_CRYPTO_CAST5=m
-+CONFIG_CRYPTO_DES=y
-+CONFIG_CRYPTO_USER_API_SKCIPHER=m
-+# CONFIG_CRYPTO_HW is not set
-+CONFIG_ARM_CRYPTO=y
-+CONFIG_CRYPTO_SHA1_ARM_NEON=m
-+CONFIG_CRYPTO_AES_ARM_BS=m
-+CONFIG_CRC_ITU_T=y
-+CONFIG_LIBCRC32C=y
---- /dev/null
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -0,0 +1,1265 @@
-+# CONFIG_ARM_PATCH_PHYS_VIRT is not set
-+CONFIG_PHYS_OFFSET=0
-+# CONFIG_LOCALVERSION_AUTO is not set
-+CONFIG_SYSVIPC=y
-+CONFIG_POSIX_MQUEUE=y
-+CONFIG_FHANDLE=y
-+CONFIG_NO_HZ=y
-+CONFIG_HIGH_RES_TIMERS=y
-+CONFIG_BSD_PROCESS_ACCT=y
-+CONFIG_BSD_PROCESS_ACCT_V3=y
-+CONFIG_TASKSTATS=y
-+CONFIG_TASK_DELAY_ACCT=y
-+CONFIG_TASK_XACCT=y
-+CONFIG_TASK_IO_ACCOUNTING=y
-+CONFIG_IKCONFIG=m
-+CONFIG_IKCONFIG_PROC=y
-+CONFIG_CGROUP_FREEZER=y
-+CONFIG_CGROUP_DEVICE=y
-+CONFIG_CPUSETS=y
-+CONFIG_CGROUP_CPUACCT=y
-+CONFIG_MEMCG=y
-+CONFIG_BLK_CGROUP=y
-+CONFIG_NAMESPACES=y
-+CONFIG_SCHED_AUTOGROUP=y
-+CONFIG_BLK_DEV_INITRD=y
-+CONFIG_EMBEDDED=y
-+# CONFIG_COMPAT_BRK is not set
-+CONFIG_PROFILING=y
-+CONFIG_OPROFILE=m
-+CONFIG_KPROBES=y
-+CONFIG_JUMP_LABEL=y
-+CONFIG_MODULES=y
-+CONFIG_MODULE_UNLOAD=y
-+CONFIG_MODVERSIONS=y
-+CONFIG_MODULE_SRCVERSION_ALL=y
-+CONFIG_BLK_DEV_THROTTLING=y
-+CONFIG_PARTITION_ADVANCED=y
-+CONFIG_MAC_PARTITION=y
-+CONFIG_CFQ_GROUP_IOSCHED=y
-+CONFIG_ARCH_BCM2708=y
-+CONFIG_PREEMPT_VOLUNTARY=y
-+CONFIG_AEABI=y
-+CONFIG_OABI_COMPAT=y
-+# CONFIG_CPU_SW_DOMAIN_PAN is not set
-+CONFIG_CLEANCACHE=y
-+CONFIG_FRONTSWAP=y
-+CONFIG_CMA=y
-+CONFIG_ZSMALLOC=m
-+CONFIG_PGTABLE_MAPPING=y
-+CONFIG_UACCESS_WITH_MEMCPY=y
-+CONFIG_SECCOMP=y
-+# CONFIG_ATAGS is not set
-+CONFIG_ZBOOT_ROM_TEXT=0x0
-+CONFIG_ZBOOT_ROM_BSS=0x0
-+CONFIG_CMDLINE="console=ttyAMA0,115200 kgdboc=ttyAMA0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 rootwait"
-+CONFIG_CPU_FREQ=y
-+CONFIG_CPU_FREQ_STAT=m
-+CONFIG_CPU_FREQ_STAT_DETAILS=y
-+CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE=y
-+CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
-+CONFIG_CPU_FREQ_GOV_USERSPACE=y
-+CONFIG_CPU_FREQ_GOV_ONDEMAND=y
-+CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
-+CONFIG_VFP=y
-+CONFIG_BINFMT_MISC=m
-+# CONFIG_SUSPEND is not set
-+CONFIG_NET=y
-+CONFIG_PACKET=y
-+CONFIG_UNIX=y
-+CONFIG_XFRM_USER=y
-+CONFIG_NET_KEY=m
-+CONFIG_INET=y
-+CONFIG_IP_MULTICAST=y
-+CONFIG_IP_ADVANCED_ROUTER=y
-+CONFIG_IP_MULTIPLE_TABLES=y
-+CONFIG_IP_ROUTE_MULTIPATH=y
-+CONFIG_IP_ROUTE_VERBOSE=y
-+CONFIG_IP_PNP=y
-+CONFIG_IP_PNP_DHCP=y
-+CONFIG_IP_PNP_RARP=y
-+CONFIG_NET_IPIP=m
-+CONFIG_NET_IPGRE_DEMUX=m
-+CONFIG_NET_IPGRE=m
-+CONFIG_IP_MROUTE=y
-+CONFIG_IP_MROUTE_MULTIPLE_TABLES=y
-+CONFIG_IP_PIMSM_V1=y
-+CONFIG_IP_PIMSM_V2=y
-+CONFIG_SYN_COOKIES=y
-+CONFIG_INET_AH=m
-+CONFIG_INET_ESP=m
-+CONFIG_INET_IPCOMP=m
-+CONFIG_INET_XFRM_MODE_TRANSPORT=m
-+CONFIG_INET_XFRM_MODE_TUNNEL=m
-+CONFIG_INET_XFRM_MODE_BEET=m
-+CONFIG_INET_LRO=m
-+CONFIG_INET_DIAG=m
-+CONFIG_INET6_AH=m
-+CONFIG_INET6_ESP=m
-+CONFIG_INET6_IPCOMP=m
-+CONFIG_IPV6_TUNNEL=m
-+CONFIG_IPV6_MULTIPLE_TABLES=y
-+CONFIG_IPV6_MROUTE=y
-+CONFIG_IPV6_MROUTE_MULTIPLE_TABLES=y
-+CONFIG_IPV6_PIMSM_V2=y
-+CONFIG_NETFILTER=y
-+CONFIG_NF_CONNTRACK=m
-+CONFIG_NF_CONNTRACK_ZONES=y
-+CONFIG_NF_CONNTRACK_EVENTS=y
-+CONFIG_NF_CONNTRACK_TIMESTAMP=y
-+CONFIG_NF_CT_PROTO_DCCP=m
-+CONFIG_NF_CT_PROTO_UDPLITE=m
-+CONFIG_NF_CONNTRACK_AMANDA=m
-+CONFIG_NF_CONNTRACK_FTP=m
-+CONFIG_NF_CONNTRACK_H323=m
-+CONFIG_NF_CONNTRACK_IRC=m
-+CONFIG_NF_CONNTRACK_NETBIOS_NS=m
-+CONFIG_NF_CONNTRACK_SNMP=m
-+CONFIG_NF_CONNTRACK_PPTP=m
-+CONFIG_NF_CONNTRACK_SANE=m
-+CONFIG_NF_CONNTRACK_SIP=m
-+CONFIG_NF_CONNTRACK_TFTP=m
-+CONFIG_NF_CT_NETLINK=m
-+CONFIG_NETFILTER_XT_SET=m
-+CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
-+CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
-+CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
-+CONFIG_NETFILTER_XT_TARGET_DSCP=m
-+CONFIG_NETFILTER_XT_TARGET_HMARK=m
-+CONFIG_NETFILTER_XT_TARGET_IDLETIMER=m
-+CONFIG_NETFILTER_XT_TARGET_LED=m
-+CONFIG_NETFILTER_XT_TARGET_LOG=m
-+CONFIG_NETFILTER_XT_TARGET_MARK=m
-+CONFIG_NETFILTER_XT_TARGET_NFLOG=m
-+CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
-+CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
-+CONFIG_NETFILTER_XT_TARGET_TEE=m
-+CONFIG_NETFILTER_XT_TARGET_TPROXY=m
-+CONFIG_NETFILTER_XT_TARGET_TRACE=m
-+CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
-+CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
-+CONFIG_NETFILTER_XT_MATCH_ADDRTYPE=m
-+CONFIG_NETFILTER_XT_MATCH_BPF=m
-+CONFIG_NETFILTER_XT_MATCH_CLUSTER=m
-+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
-+CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
-+CONFIG_NETFILTER_XT_MATCH_CONNLABEL=m
-+CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
-+CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
-+CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
-+CONFIG_NETFILTER_XT_MATCH_CPU=m
-+CONFIG_NETFILTER_XT_MATCH_DCCP=m
-+CONFIG_NETFILTER_XT_MATCH_DEVGROUP=m
-+CONFIG_NETFILTER_XT_MATCH_DSCP=m
-+CONFIG_NETFILTER_XT_MATCH_ESP=m
-+CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
-+CONFIG_NETFILTER_XT_MATCH_HELPER=m
-+CONFIG_NETFILTER_XT_MATCH_IPRANGE=m
-+CONFIG_NETFILTER_XT_MATCH_IPVS=m
-+CONFIG_NETFILTER_XT_MATCH_LENGTH=m
-+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
-+CONFIG_NETFILTER_XT_MATCH_MAC=m
-+CONFIG_NETFILTER_XT_MATCH_MARK=m
-+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
-+CONFIG_NETFILTER_XT_MATCH_NFACCT=m
-+CONFIG_NETFILTER_XT_MATCH_OSF=m
-+CONFIG_NETFILTER_XT_MATCH_OWNER=m
-+CONFIG_NETFILTER_XT_MATCH_POLICY=m
-+CONFIG_NETFILTER_XT_MATCH_PHYSDEV=m
-+CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
-+CONFIG_NETFILTER_XT_MATCH_QUOTA=m
-+CONFIG_NETFILTER_XT_MATCH_RATEEST=m
-+CONFIG_NETFILTER_XT_MATCH_REALM=m
-+CONFIG_NETFILTER_XT_MATCH_RECENT=m
-+CONFIG_NETFILTER_XT_MATCH_SOCKET=m
-+CONFIG_NETFILTER_XT_MATCH_STATE=m
-+CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
-+CONFIG_NETFILTER_XT_MATCH_STRING=m
-+CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
-+CONFIG_NETFILTER_XT_MATCH_TIME=m
-+CONFIG_NETFILTER_XT_MATCH_U32=m
-+CONFIG_IP_SET=m
-+CONFIG_IP_SET_BITMAP_IP=m
-+CONFIG_IP_SET_BITMAP_IPMAC=m
-+CONFIG_IP_SET_BITMAP_PORT=m
-+CONFIG_IP_SET_HASH_IP=m
-+CONFIG_IP_SET_HASH_IPPORT=m
-+CONFIG_IP_SET_HASH_IPPORTIP=m
-+CONFIG_IP_SET_HASH_IPPORTNET=m
-+CONFIG_IP_SET_HASH_NET=m
-+CONFIG_IP_SET_HASH_NETPORT=m
-+CONFIG_IP_SET_HASH_NETIFACE=m
-+CONFIG_IP_SET_LIST_SET=m
-+CONFIG_IP_VS=m
-+CONFIG_IP_VS_PROTO_TCP=y
-+CONFIG_IP_VS_PROTO_UDP=y
-+CONFIG_IP_VS_PROTO_ESP=y
-+CONFIG_IP_VS_PROTO_AH=y
-+CONFIG_IP_VS_PROTO_SCTP=y
-+CONFIG_IP_VS_RR=m
-+CONFIG_IP_VS_WRR=m
-+CONFIG_IP_VS_LC=m
-+CONFIG_IP_VS_WLC=m
-+CONFIG_IP_VS_LBLC=m
-+CONFIG_IP_VS_LBLCR=m
-+CONFIG_IP_VS_DH=m
-+CONFIG_IP_VS_SH=m
-+CONFIG_IP_VS_SED=m
-+CONFIG_IP_VS_NQ=m
-+CONFIG_IP_VS_FTP=m
-+CONFIG_IP_VS_PE_SIP=m
-+CONFIG_NF_CONNTRACK_IPV4=m
-+CONFIG_IP_NF_IPTABLES=m
-+CONFIG_IP_NF_MATCH_AH=m
-+CONFIG_IP_NF_MATCH_ECN=m
-+CONFIG_IP_NF_MATCH_TTL=m
-+CONFIG_IP_NF_FILTER=m
-+CONFIG_IP_NF_TARGET_REJECT=m
-+CONFIG_IP_NF_NAT=m
-+CONFIG_IP_NF_TARGET_MASQUERADE=m
-+CONFIG_IP_NF_TARGET_NETMAP=m
-+CONFIG_IP_NF_TARGET_REDIRECT=m
-+CONFIG_IP_NF_MANGLE=m
-+CONFIG_IP_NF_TARGET_CLUSTERIP=m
-+CONFIG_IP_NF_TARGET_ECN=m
-+CONFIG_IP_NF_TARGET_TTL=m
-+CONFIG_IP_NF_RAW=m
-+CONFIG_IP_NF_ARPTABLES=m
-+CONFIG_IP_NF_ARPFILTER=m
-+CONFIG_IP_NF_ARP_MANGLE=m
-+CONFIG_NF_CONNTRACK_IPV6=m
-+CONFIG_IP6_NF_IPTABLES=m
-+CONFIG_IP6_NF_MATCH_AH=m
-+CONFIG_IP6_NF_MATCH_EUI64=m
-+CONFIG_IP6_NF_MATCH_FRAG=m
-+CONFIG_IP6_NF_MATCH_OPTS=m
-+CONFIG_IP6_NF_MATCH_HL=m
-+CONFIG_IP6_NF_MATCH_IPV6HEADER=m
-+CONFIG_IP6_NF_MATCH_MH=m
-+CONFIG_IP6_NF_MATCH_RT=m
-+CONFIG_IP6_NF_TARGET_HL=m
-+CONFIG_IP6_NF_FILTER=m
-+CONFIG_IP6_NF_TARGET_REJECT=m
-+CONFIG_IP6_NF_MANGLE=m
-+CONFIG_IP6_NF_RAW=m
-+CONFIG_IP6_NF_NAT=m
-+CONFIG_IP6_NF_TARGET_MASQUERADE=m
-+CONFIG_IP6_NF_TARGET_NPT=m
-+CONFIG_BRIDGE_NF_EBTABLES=m
-+CONFIG_BRIDGE_EBT_BROUTE=m
-+CONFIG_BRIDGE_EBT_T_FILTER=m
-+CONFIG_BRIDGE_EBT_T_NAT=m
-+CONFIG_BRIDGE_EBT_802_3=m
-+CONFIG_BRIDGE_EBT_AMONG=m
-+CONFIG_BRIDGE_EBT_ARP=m
-+CONFIG_BRIDGE_EBT_IP=m
-+CONFIG_BRIDGE_EBT_IP6=m
-+CONFIG_BRIDGE_EBT_LIMIT=m
-+CONFIG_BRIDGE_EBT_MARK=m
-+CONFIG_BRIDGE_EBT_PKTTYPE=m
-+CONFIG_BRIDGE_EBT_STP=m
-+CONFIG_BRIDGE_EBT_VLAN=m
-+CONFIG_BRIDGE_EBT_ARPREPLY=m
-+CONFIG_BRIDGE_EBT_DNAT=m
-+CONFIG_BRIDGE_EBT_MARK_T=m
-+CONFIG_BRIDGE_EBT_REDIRECT=m
-+CONFIG_BRIDGE_EBT_SNAT=m
-+CONFIG_BRIDGE_EBT_LOG=m
-+CONFIG_BRIDGE_EBT_NFLOG=m
-+CONFIG_SCTP_COOKIE_HMAC_SHA1=y
-+CONFIG_ATM=m
-+CONFIG_L2TP=m
-+CONFIG_L2TP_V3=y
-+CONFIG_L2TP_IP=m
-+CONFIG_L2TP_ETH=m
-+CONFIG_BRIDGE=m
-+CONFIG_VLAN_8021Q=m
-+CONFIG_VLAN_8021Q_GVRP=y
-+CONFIG_ATALK=m
-+CONFIG_6LOWPAN=m
-+CONFIG_IEEE802154=m
-+CONFIG_IEEE802154_6LOWPAN=m
-+CONFIG_MAC802154=m
-+CONFIG_NET_SCHED=y
-+CONFIG_NET_SCH_CBQ=m
-+CONFIG_NET_SCH_HTB=m
-+CONFIG_NET_SCH_HFSC=m
-+CONFIG_NET_SCH_PRIO=m
-+CONFIG_NET_SCH_MULTIQ=m
-+CONFIG_NET_SCH_RED=m
-+CONFIG_NET_SCH_SFB=m
-+CONFIG_NET_SCH_SFQ=m
-+CONFIG_NET_SCH_TEQL=m
-+CONFIG_NET_SCH_TBF=m
-+CONFIG_NET_SCH_GRED=m
-+CONFIG_NET_SCH_DSMARK=m
-+CONFIG_NET_SCH_NETEM=m
-+CONFIG_NET_SCH_DRR=m
-+CONFIG_NET_SCH_MQPRIO=m
-+CONFIG_NET_SCH_CHOKE=m
-+CONFIG_NET_SCH_QFQ=m
-+CONFIG_NET_SCH_CODEL=m
-+CONFIG_NET_SCH_FQ_CODEL=m
-+CONFIG_NET_SCH_INGRESS=m
-+CONFIG_NET_SCH_PLUG=m
-+CONFIG_NET_CLS_BASIC=m
-+CONFIG_NET_CLS_TCINDEX=m
-+CONFIG_NET_CLS_ROUTE4=m
-+CONFIG_NET_CLS_FW=m
-+CONFIG_NET_CLS_U32=m
-+CONFIG_CLS_U32_MARK=y
-+CONFIG_NET_CLS_RSVP=m
-+CONFIG_NET_CLS_RSVP6=m
-+CONFIG_NET_CLS_FLOW=m
-+CONFIG_NET_CLS_CGROUP=m
-+CONFIG_NET_EMATCH=y
-+CONFIG_NET_EMATCH_CMP=m
-+CONFIG_NET_EMATCH_NBYTE=m
-+CONFIG_NET_EMATCH_U32=m
-+CONFIG_NET_EMATCH_META=m
-+CONFIG_NET_EMATCH_TEXT=m
-+CONFIG_NET_EMATCH_IPSET=m
-+CONFIG_NET_CLS_ACT=y
-+CONFIG_NET_ACT_POLICE=m
-+CONFIG_NET_ACT_GACT=m
-+CONFIG_GACT_PROB=y
-+CONFIG_NET_ACT_MIRRED=m
-+CONFIG_NET_ACT_IPT=m
-+CONFIG_NET_ACT_NAT=m
-+CONFIG_NET_ACT_PEDIT=m
-+CONFIG_NET_ACT_SIMP=m
-+CONFIG_NET_ACT_SKBEDIT=m
-+CONFIG_NET_ACT_CSUM=m
-+CONFIG_BATMAN_ADV=m
-+CONFIG_OPENVSWITCH=m
-+CONFIG_NET_PKTGEN=m
-+CONFIG_HAMRADIO=y
-+CONFIG_AX25=m
-+CONFIG_NETROM=m
-+CONFIG_ROSE=m
-+CONFIG_MKISS=m
-+CONFIG_6PACK=m
-+CONFIG_BPQETHER=m
-+CONFIG_BAYCOM_SER_FDX=m
-+CONFIG_BAYCOM_SER_HDX=m
-+CONFIG_YAM=m
-+CONFIG_CAN=m
-+CONFIG_CAN_VCAN=m
-+CONFIG_CAN_MCP251X=m
-+CONFIG_IRDA=m
-+CONFIG_IRLAN=m
-+CONFIG_IRNET=m
-+CONFIG_IRCOMM=m
-+CONFIG_IRDA_ULTRA=y
-+CONFIG_IRDA_CACHE_LAST_LSAP=y
-+CONFIG_IRDA_FAST_RR=y
-+CONFIG_IRTTY_SIR=m
-+CONFIG_KINGSUN_DONGLE=m
-+CONFIG_KSDAZZLE_DONGLE=m
-+CONFIG_KS959_DONGLE=m
-+CONFIG_USB_IRDA=m
-+CONFIG_SIGMATEL_FIR=m
-+CONFIG_MCS_FIR=m
-+CONFIG_BT=m
-+CONFIG_BT_RFCOMM=m
-+CONFIG_BT_RFCOMM_TTY=y
-+CONFIG_BT_BNEP=m
-+CONFIG_BT_BNEP_MC_FILTER=y
-+CONFIG_BT_BNEP_PROTO_FILTER=y
-+CONFIG_BT_HIDP=m
-+CONFIG_BT_6LOWPAN=m
-+CONFIG_BT_HCIBTUSB=m
-+CONFIG_BT_HCIUART=m
-+CONFIG_BT_HCIBCM203X=m
-+CONFIG_BT_HCIBPA10X=m
-+CONFIG_BT_HCIBFUSB=m
-+CONFIG_BT_HCIVHCI=m
-+CONFIG_BT_MRVL=m
-+CONFIG_BT_MRVL_SDIO=m
-+CONFIG_BT_ATH3K=m
-+CONFIG_BT_WILINK=m
-+CONFIG_MAC80211=m
-+CONFIG_MAC80211_MESH=y
-+CONFIG_WIMAX=m
-+CONFIG_RFKILL=m
-+CONFIG_RFKILL_INPUT=y
-+CONFIG_NET_9P=m
-+CONFIG_NFC=m
-+CONFIG_NFC_PN533=m
-+CONFIG_DEVTMPFS=y
-+CONFIG_DEVTMPFS_MOUNT=y
-+CONFIG_DMA_CMA=y
-+CONFIG_CMA_SIZE_MBYTES=5
-+CONFIG_MTD=m
-+CONFIG_MTD_BLOCK=m
-+CONFIG_MTD_NAND=m
-+CONFIG_MTD_UBI=m
-+CONFIG_ZRAM=m
-+CONFIG_ZRAM_LZ4_COMPRESS=y
-+CONFIG_BLK_DEV_LOOP=y
-+CONFIG_BLK_DEV_CRYPTOLOOP=m
-+CONFIG_BLK_DEV_DRBD=m
-+CONFIG_BLK_DEV_NBD=m
-+CONFIG_BLK_DEV_RAM=y
-+CONFIG_CDROM_PKTCDVD=m
-+CONFIG_ATA_OVER_ETH=m
-+CONFIG_EEPROM_AT24=m
-+CONFIG_TI_ST=m
-+CONFIG_SCSI=y
-+# CONFIG_SCSI_PROC_FS is not set
-+CONFIG_BLK_DEV_SD=y
-+CONFIG_CHR_DEV_ST=m
-+CONFIG_CHR_DEV_OSST=m
-+CONFIG_BLK_DEV_SR=m
-+CONFIG_CHR_DEV_SG=m
-+CONFIG_SCSI_ISCSI_ATTRS=y
-+CONFIG_ISCSI_TCP=m
-+CONFIG_ISCSI_BOOT_SYSFS=m
-+CONFIG_MD=y
-+CONFIG_MD_LINEAR=m
-+CONFIG_MD_RAID0=m
-+CONFIG_BLK_DEV_DM=m
-+CONFIG_DM_CRYPT=m
-+CONFIG_DM_SNAPSHOT=m
-+CONFIG_DM_THIN_PROVISIONING=m
-+CONFIG_DM_MIRROR=m
-+CONFIG_DM_LOG_USERSPACE=m
-+CONFIG_DM_RAID=m
-+CONFIG_DM_ZERO=m
-+CONFIG_DM_DELAY=m
-+CONFIG_NETDEVICES=y
-+CONFIG_BONDING=m
-+CONFIG_DUMMY=m
-+CONFIG_IFB=m
-+CONFIG_MACVLAN=m
-+CONFIG_NETCONSOLE=m
-+CONFIG_TUN=m
-+CONFIG_VETH=m
-+CONFIG_ENC28J60=m
-+CONFIG_MDIO_BITBANG=m
-+CONFIG_PPP=m
-+CONFIG_PPP_BSDCOMP=m
-+CONFIG_PPP_DEFLATE=m
-+CONFIG_PPP_FILTER=y
-+CONFIG_PPP_MPPE=m
-+CONFIG_PPP_MULTILINK=y
-+CONFIG_PPPOATM=m
-+CONFIG_PPPOE=m
-+CONFIG_PPPOL2TP=m
-+CONFIG_PPP_ASYNC=m
-+CONFIG_PPP_SYNC_TTY=m
-+CONFIG_SLIP=m
-+CONFIG_SLIP_COMPRESSED=y
-+CONFIG_SLIP_SMART=y
-+CONFIG_USB_CATC=m
-+CONFIG_USB_KAWETH=m
-+CONFIG_USB_PEGASUS=m
-+CONFIG_USB_RTL8150=m
-+CONFIG_USB_RTL8152=m
-+CONFIG_USB_USBNET=y
-+CONFIG_USB_NET_AX8817X=m
-+CONFIG_USB_NET_AX88179_178A=m
-+CONFIG_USB_NET_CDCETHER=m
-+CONFIG_USB_NET_CDC_EEM=m
-+CONFIG_USB_NET_CDC_NCM=m
-+CONFIG_USB_NET_HUAWEI_CDC_NCM=m
-+CONFIG_USB_NET_CDC_MBIM=m
-+CONFIG_USB_NET_DM9601=m
-+CONFIG_USB_NET_SR9700=m
-+CONFIG_USB_NET_SR9800=m
-+CONFIG_USB_NET_SMSC75XX=m
-+CONFIG_USB_NET_SMSC95XX=y
-+CONFIG_USB_NET_GL620A=m
-+CONFIG_USB_NET_NET1080=m
-+CONFIG_USB_NET_PLUSB=m
-+CONFIG_USB_NET_MCS7830=m
-+CONFIG_USB_NET_CDC_SUBSET=m
-+CONFIG_USB_ALI_M5632=y
-+CONFIG_USB_AN2720=y
-+CONFIG_USB_EPSON2888=y
-+CONFIG_USB_KC2190=y
-+CONFIG_USB_NET_ZAURUS=m
-+CONFIG_USB_NET_CX82310_ETH=m
-+CONFIG_USB_NET_KALMIA=m
-+CONFIG_USB_NET_QMI_WWAN=m
-+CONFIG_USB_HSO=m
-+CONFIG_USB_NET_INT51X1=m
-+CONFIG_USB_IPHETH=m
-+CONFIG_USB_SIERRA_NET=m
-+CONFIG_USB_VL600=m
-+CONFIG_LIBERTAS_THINFIRM=m
-+CONFIG_LIBERTAS_THINFIRM_USB=m
-+CONFIG_AT76C50X_USB=m
-+CONFIG_USB_ZD1201=m
-+CONFIG_USB_NET_RNDIS_WLAN=m
-+CONFIG_RTL8187=m
-+CONFIG_MAC80211_HWSIM=m
-+CONFIG_ATH_CARDS=m
-+CONFIG_ATH9K=m
-+CONFIG_ATH9K_HTC=m
-+CONFIG_CARL9170=m
-+CONFIG_ATH6KL=m
-+CONFIG_ATH6KL_USB=m
-+CONFIG_AR5523=m
-+CONFIG_B43=m
-+# CONFIG_B43_PHY_N is not set
-+CONFIG_B43LEGACY=m
-+CONFIG_BRCMFMAC=m
-+CONFIG_BRCMFMAC_USB=y
-+CONFIG_HOSTAP=m
-+CONFIG_LIBERTAS=m
-+CONFIG_LIBERTAS_USB=m
-+CONFIG_LIBERTAS_SDIO=m
-+CONFIG_P54_COMMON=m
-+CONFIG_P54_USB=m
-+CONFIG_RT2X00=m
-+CONFIG_RT2500USB=m
-+CONFIG_RT73USB=m
-+CONFIG_RT2800USB=m
-+CONFIG_RT2800USB_RT3573=y
-+CONFIG_RT2800USB_RT53XX=y
-+CONFIG_RT2800USB_RT55XX=y
-+CONFIG_RT2800USB_UNKNOWN=y
-+CONFIG_WL_MEDIATEK=y
-+CONFIG_MT7601U=m
-+CONFIG_RTL8192CU=m
-+CONFIG_ZD1211RW=m
-+CONFIG_MWIFIEX=m
-+CONFIG_MWIFIEX_SDIO=m
-+CONFIG_WIMAX_I2400M_USB=m
-+CONFIG_IEEE802154_AT86RF230=m
-+CONFIG_IEEE802154_MRF24J40=m
-+CONFIG_IEEE802154_CC2520=m
-+CONFIG_INPUT_POLLDEV=m
-+# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-+CONFIG_INPUT_JOYDEV=m
-+CONFIG_INPUT_EVDEV=m
-+# CONFIG_KEYBOARD_ATKBD is not set
-+CONFIG_KEYBOARD_GPIO=m
-+# CONFIG_INPUT_MOUSE is not set
-+CONFIG_INPUT_JOYSTICK=y
-+CONFIG_JOYSTICK_IFORCE=m
-+CONFIG_JOYSTICK_IFORCE_USB=y
-+CONFIG_JOYSTICK_XPAD=m
-+CONFIG_JOYSTICK_XPAD_FF=y
-+CONFIG_JOYSTICK_RPISENSE=m
-+CONFIG_INPUT_TOUCHSCREEN=y
-+CONFIG_TOUCHSCREEN_ADS7846=m
-+CONFIG_TOUCHSCREEN_EGALAX=m
-+CONFIG_TOUCHSCREEN_FT6236=m
-+CONFIG_TOUCHSCREEN_RPI_FT5406=m
-+CONFIG_TOUCHSCREEN_USB_COMPOSITE=m
-+CONFIG_TOUCHSCREEN_STMPE=m
-+CONFIG_INPUT_MISC=y
-+CONFIG_INPUT_AD714X=m
-+CONFIG_INPUT_ATI_REMOTE2=m
-+CONFIG_INPUT_KEYSPAN_REMOTE=m
-+CONFIG_INPUT_POWERMATE=m
-+CONFIG_INPUT_YEALINK=m
-+CONFIG_INPUT_CM109=m
-+CONFIG_INPUT_UINPUT=m
-+CONFIG_INPUT_GPIO_ROTARY_ENCODER=m
-+CONFIG_INPUT_ADXL34X=m
-+CONFIG_INPUT_CMA3000=m
-+CONFIG_SERIO=m
-+CONFIG_SERIO_RAW=m
-+CONFIG_GAMEPORT=m
-+CONFIG_GAMEPORT_NS558=m
-+CONFIG_GAMEPORT_L4=m
-+CONFIG_BRCM_CHAR_DRIVERS=y
-+CONFIG_BCM_VC_CMA=y
-+CONFIG_BCM_VCIO=y
-+CONFIG_BCM_VC_SM=y
-+CONFIG_DEVPTS_MULTIPLE_INSTANCES=y
-+# CONFIG_LEGACY_PTYS is not set
-+# CONFIG_DEVKMEM is not set
-+CONFIG_SERIAL_8250=y
-+# CONFIG_SERIAL_8250_DEPRECATED_OPTIONS is not set
-+CONFIG_SERIAL_8250_CONSOLE=y
-+# CONFIG_SERIAL_8250_DMA is not set
-+CONFIG_SERIAL_8250_NR_UARTS=1
-+CONFIG_SERIAL_8250_RUNTIME_UARTS=0
-+CONFIG_SERIAL_AMBA_PL011=y
-+CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
-+CONFIG_SERIAL_OF_PLATFORM=y
-+CONFIG_TTY_PRINTK=y
-+CONFIG_HW_RANDOM=y
-+CONFIG_RAW_DRIVER=y
-+CONFIG_I2C=y
-+CONFIG_I2C_CHARDEV=m
-+CONFIG_I2C_BCM2708=m
-+CONFIG_SPI=y
-+CONFIG_SPI_BCM2835=m
-+CONFIG_SPI_SPIDEV=y
-+CONFIG_PPS=m
-+CONFIG_PPS_CLIENT_LDISC=m
-+CONFIG_PPS_CLIENT_GPIO=m
-+CONFIG_GPIO_SYSFS=y
-+CONFIG_GPIO_ARIZONA=m
-+CONFIG_GPIO_STMPE=y
-+CONFIG_W1=m
-+CONFIG_W1_MASTER_DS2490=m
-+CONFIG_W1_MASTER_DS2482=m
-+CONFIG_W1_MASTER_DS1WM=m
-+CONFIG_W1_MASTER_GPIO=m
-+CONFIG_W1_SLAVE_THERM=m
-+CONFIG_W1_SLAVE_SMEM=m
-+CONFIG_W1_SLAVE_DS2408=m
-+CONFIG_W1_SLAVE_DS2413=m
-+CONFIG_W1_SLAVE_DS2406=m
-+CONFIG_W1_SLAVE_DS2423=m
-+CONFIG_W1_SLAVE_DS2431=m
-+CONFIG_W1_SLAVE_DS2433=m
-+CONFIG_W1_SLAVE_DS2760=m
-+CONFIG_W1_SLAVE_DS2780=m
-+CONFIG_W1_SLAVE_DS2781=m
-+CONFIG_W1_SLAVE_DS28E04=m
-+CONFIG_W1_SLAVE_BQ27000=m
-+CONFIG_BATTERY_DS2760=m
-+CONFIG_POWER_RESET=y
-+CONFIG_POWER_RESET_GPIO=y
-+CONFIG_HWMON=m
-+CONFIG_SENSORS_SHT21=m
-+CONFIG_SENSORS_SHTC1=m
-+CONFIG_THERMAL=y
-+CONFIG_THERMAL_BCM2835=y
-+CONFIG_WATCHDOG=y
-+CONFIG_BCM2835_WDT=m
-+CONFIG_UCB1400_CORE=m
-+CONFIG_MFD_STMPE=y
-+CONFIG_STMPE_SPI=y
-+CONFIG_MFD_ARIZONA_I2C=m
-+CONFIG_MFD_ARIZONA_SPI=m
-+CONFIG_MFD_WM5102=y
-+CONFIG_MEDIA_SUPPORT=m
-+CONFIG_MEDIA_CAMERA_SUPPORT=y
-+CONFIG_MEDIA_ANALOG_TV_SUPPORT=y
-+CONFIG_MEDIA_DIGITAL_TV_SUPPORT=y
-+CONFIG_MEDIA_RADIO_SUPPORT=y
-+CONFIG_MEDIA_RC_SUPPORT=y
-+CONFIG_MEDIA_CONTROLLER=y
-+CONFIG_LIRC=m
-+CONFIG_RC_DEVICES=y
-+CONFIG_RC_ATI_REMOTE=m
-+CONFIG_IR_IMON=m
-+CONFIG_IR_MCEUSB=m
-+CONFIG_IR_REDRAT3=m
-+CONFIG_IR_STREAMZAP=m
-+CONFIG_IR_IGUANA=m
-+CONFIG_IR_TTUSBIR=m
-+CONFIG_RC_LOOPBACK=m
-+CONFIG_IR_GPIO_CIR=m
-+CONFIG_MEDIA_USB_SUPPORT=y
-+CONFIG_USB_VIDEO_CLASS=m
-+CONFIG_USB_M5602=m
-+CONFIG_USB_STV06XX=m
-+CONFIG_USB_GL860=m
-+CONFIG_USB_GSPCA_BENQ=m
-+CONFIG_USB_GSPCA_CONEX=m
-+CONFIG_USB_GSPCA_CPIA1=m
-+CONFIG_USB_GSPCA_DTCS033=m
-+CONFIG_USB_GSPCA_ETOMS=m
-+CONFIG_USB_GSPCA_FINEPIX=m
-+CONFIG_USB_GSPCA_JEILINJ=m
-+CONFIG_USB_GSPCA_JL2005BCD=m
-+CONFIG_USB_GSPCA_KINECT=m
-+CONFIG_USB_GSPCA_KONICA=m
-+CONFIG_USB_GSPCA_MARS=m
-+CONFIG_USB_GSPCA_MR97310A=m
-+CONFIG_USB_GSPCA_NW80X=m
-+CONFIG_USB_GSPCA_OV519=m
-+CONFIG_USB_GSPCA_OV534=m
-+CONFIG_USB_GSPCA_OV534_9=m
-+CONFIG_USB_GSPCA_PAC207=m
-+CONFIG_USB_GSPCA_PAC7302=m
-+CONFIG_USB_GSPCA_PAC7311=m
-+CONFIG_USB_GSPCA_SE401=m
-+CONFIG_USB_GSPCA_SN9C2028=m
-+CONFIG_USB_GSPCA_SN9C20X=m
-+CONFIG_USB_GSPCA_SONIXB=m
-+CONFIG_USB_GSPCA_SONIXJ=m
-+CONFIG_USB_GSPCA_SPCA500=m
-+CONFIG_USB_GSPCA_SPCA501=m
-+CONFIG_USB_GSPCA_SPCA505=m
-+CONFIG_USB_GSPCA_SPCA506=m
-+CONFIG_USB_GSPCA_SPCA508=m
-+CONFIG_USB_GSPCA_SPCA561=m
-+CONFIG_USB_GSPCA_SPCA1528=m
-+CONFIG_USB_GSPCA_SQ905=m
-+CONFIG_USB_GSPCA_SQ905C=m
-+CONFIG_USB_GSPCA_SQ930X=m
-+CONFIG_USB_GSPCA_STK014=m
-+CONFIG_USB_GSPCA_STK1135=m
-+CONFIG_USB_GSPCA_STV0680=m
-+CONFIG_USB_GSPCA_SUNPLUS=m
-+CONFIG_USB_GSPCA_T613=m
-+CONFIG_USB_GSPCA_TOPRO=m
-+CONFIG_USB_GSPCA_TV8532=m
-+CONFIG_USB_GSPCA_VC032X=m
-+CONFIG_USB_GSPCA_VICAM=m
-+CONFIG_USB_GSPCA_XIRLINK_CIT=m
-+CONFIG_USB_GSPCA_ZC3XX=m
-+CONFIG_USB_PWC=m
-+CONFIG_VIDEO_CPIA2=m
-+CONFIG_USB_ZR364XX=m
-+CONFIG_USB_STKWEBCAM=m
-+CONFIG_USB_S2255=m
-+CONFIG_VIDEO_USBTV=m
-+CONFIG_VIDEO_PVRUSB2=m
-+CONFIG_VIDEO_HDPVR=m
-+CONFIG_VIDEO_USBVISION=m
-+CONFIG_VIDEO_STK1160_COMMON=m
-+CONFIG_VIDEO_STK1160_AC97=y
-+CONFIG_VIDEO_GO7007=m
-+CONFIG_VIDEO_GO7007_USB=m
-+CONFIG_VIDEO_GO7007_USB_S2250_BOARD=m
-+CONFIG_VIDEO_AU0828=m
-+CONFIG_VIDEO_AU0828_RC=y
-+CONFIG_VIDEO_CX231XX=m
-+CONFIG_VIDEO_CX231XX_ALSA=m
-+CONFIG_VIDEO_CX231XX_DVB=m
-+CONFIG_VIDEO_TM6000=m
-+CONFIG_VIDEO_TM6000_ALSA=m
-+CONFIG_VIDEO_TM6000_DVB=m
-+CONFIG_DVB_USB=m
-+CONFIG_DVB_USB_A800=m
-+CONFIG_DVB_USB_DIBUSB_MB=m
-+CONFIG_DVB_USB_DIBUSB_MB_FAULTY=y
-+CONFIG_DVB_USB_DIBUSB_MC=m
-+CONFIG_DVB_USB_DIB0700=m
-+CONFIG_DVB_USB_UMT_010=m
-+CONFIG_DVB_USB_CXUSB=m
-+CONFIG_DVB_USB_M920X=m
-+CONFIG_DVB_USB_DIGITV=m
-+CONFIG_DVB_USB_VP7045=m
-+CONFIG_DVB_USB_VP702X=m
-+CONFIG_DVB_USB_GP8PSK=m
-+CONFIG_DVB_USB_NOVA_T_USB2=m
-+CONFIG_DVB_USB_TTUSB2=m
-+CONFIG_DVB_USB_DTT200U=m
-+CONFIG_DVB_USB_OPERA1=m
-+CONFIG_DVB_USB_AF9005=m
-+CONFIG_DVB_USB_AF9005_REMOTE=m
-+CONFIG_DVB_USB_PCTV452E=m
-+CONFIG_DVB_USB_DW2102=m
-+CONFIG_DVB_USB_CINERGY_T2=m
-+CONFIG_DVB_USB_DTV5100=m
-+CONFIG_DVB_USB_FRIIO=m
-+CONFIG_DVB_USB_AZ6027=m
-+CONFIG_DVB_USB_TECHNISAT_USB2=m
-+CONFIG_DVB_USB_V2=m
-+CONFIG_DVB_USB_AF9015=m
-+CONFIG_DVB_USB_AF9035=m
-+CONFIG_DVB_USB_ANYSEE=m
-+CONFIG_DVB_USB_AU6610=m
-+CONFIG_DVB_USB_AZ6007=m
-+CONFIG_DVB_USB_CE6230=m
-+CONFIG_DVB_USB_EC168=m
-+CONFIG_DVB_USB_GL861=m
-+CONFIG_DVB_USB_LME2510=m
-+CONFIG_DVB_USB_MXL111SF=m
-+CONFIG_DVB_USB_RTL28XXU=m
-+CONFIG_DVB_USB_DVBSKY=m
-+CONFIG_SMS_USB_DRV=m
-+CONFIG_DVB_B2C2_FLEXCOP_USB=m
-+CONFIG_DVB_AS102=m
-+CONFIG_VIDEO_EM28XX=m
-+CONFIG_VIDEO_EM28XX_V4L2=m
-+CONFIG_VIDEO_EM28XX_ALSA=m
-+CONFIG_VIDEO_EM28XX_DVB=m
-+CONFIG_V4L_PLATFORM_DRIVERS=y
-+CONFIG_VIDEO_BCM2835=y
-+CONFIG_VIDEO_BCM2835_MMAL=m
-+CONFIG_RADIO_SI470X=y
-+CONFIG_USB_SI470X=m
-+CONFIG_I2C_SI470X=m
-+CONFIG_RADIO_SI4713=m
-+CONFIG_I2C_SI4713=m
-+CONFIG_USB_MR800=m
-+CONFIG_USB_DSBR=m
-+CONFIG_RADIO_SHARK=m
-+CONFIG_RADIO_SHARK2=m
-+CONFIG_USB_KEENE=m
-+CONFIG_USB_MA901=m
-+CONFIG_RADIO_TEA5764=m
-+CONFIG_RADIO_SAA7706H=m
-+CONFIG_RADIO_TEF6862=m
-+CONFIG_RADIO_WL1273=m
-+CONFIG_RADIO_WL128X=m
-+# CONFIG_MEDIA_SUBDRV_AUTOSELECT is not set
-+CONFIG_VIDEO_UDA1342=m
-+CONFIG_VIDEO_SONY_BTF_MPX=m
-+CONFIG_VIDEO_TVP5150=m
-+CONFIG_VIDEO_TW2804=m
-+CONFIG_VIDEO_TW9903=m
-+CONFIG_VIDEO_TW9906=m
-+CONFIG_VIDEO_OV7640=m
-+CONFIG_VIDEO_MT9V011=m
-+CONFIG_FB=y
-+CONFIG_FB_BCM2708=y
-+CONFIG_FB_UDL=m
-+CONFIG_FB_SSD1307=m
-+CONFIG_FB_RPISENSE=m
-+# CONFIG_BACKLIGHT_GENERIC is not set
-+CONFIG_BACKLIGHT_GPIO=m
-+CONFIG_FRAMEBUFFER_CONSOLE=y
-+CONFIG_LOGO=y
-+# CONFIG_LOGO_LINUX_MONO is not set
-+# CONFIG_LOGO_LINUX_VGA16 is not set
-+CONFIG_SOUND=y
-+CONFIG_SND=m
-+CONFIG_SND_SEQUENCER=m
-+CONFIG_SND_SEQ_DUMMY=m
-+CONFIG_SND_MIXER_OSS=m
-+CONFIG_SND_PCM_OSS=m
-+CONFIG_SND_SEQUENCER_OSS=y
-+CONFIG_SND_HRTIMER=m
-+CONFIG_SND_DUMMY=m
-+CONFIG_SND_ALOOP=m
-+CONFIG_SND_VIRMIDI=m
-+CONFIG_SND_MTPAV=m
-+CONFIG_SND_SERIAL_U16550=m
-+CONFIG_SND_MPU401=m
-+CONFIG_SND_BCM2835=m
-+CONFIG_SND_USB_AUDIO=m
-+CONFIG_SND_USB_UA101=m
-+CONFIG_SND_USB_CAIAQ=m
-+CONFIG_SND_USB_CAIAQ_INPUT=y
-+CONFIG_SND_USB_6FIRE=m
-+CONFIG_SND_SOC=m
-+CONFIG_SND_BCM2835_SOC_I2S=m
-+CONFIG_SND_BCM2708_SOC_HIFIBERRY_DAC=m
-+CONFIG_SND_BCM2708_SOC_HIFIBERRY_DACPLUS=m
-+CONFIG_SND_BCM2708_SOC_HIFIBERRY_DIGI=m
-+CONFIG_SND_BCM2708_SOC_HIFIBERRY_AMP=m
-+CONFIG_SND_BCM2708_SOC_RPI_DAC=m
-+CONFIG_SND_BCM2708_SOC_RPI_PROTO=m
-+CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC=m
-+CONFIG_SND_BCM2708_SOC_RASPIDAC3=m
-+CONFIG_SND_SOC_ADAU1701=m
-+CONFIG_SND_SOC_WM8804_I2C=m
-+CONFIG_SND_SIMPLE_CARD=m
-+CONFIG_SOUND_PRIME=m
-+CONFIG_HIDRAW=y
-+CONFIG_UHID=m
-+CONFIG_HID_A4TECH=m
-+CONFIG_HID_ACRUX=m
-+CONFIG_HID_APPLE=m
-+CONFIG_HID_BELKIN=m
-+CONFIG_HID_CHERRY=m
-+CONFIG_HID_CHICONY=m
-+CONFIG_HID_CYPRESS=m
-+CONFIG_HID_DRAGONRISE=m
-+CONFIG_HID_EMS_FF=m
-+CONFIG_HID_ELECOM=m
-+CONFIG_HID_ELO=m
-+CONFIG_HID_EZKEY=m
-+CONFIG_HID_HOLTEK=m
-+CONFIG_HID_KEYTOUCH=m
-+CONFIG_HID_KYE=m
-+CONFIG_HID_UCLOGIC=m
-+CONFIG_HID_WALTOP=m
-+CONFIG_HID_GYRATION=m
-+CONFIG_HID_TWINHAN=m
-+CONFIG_HID_KENSINGTON=m
-+CONFIG_HID_LCPOWER=m
-+CONFIG_HID_LOGITECH=m
-+CONFIG_HID_MAGICMOUSE=m
-+CONFIG_HID_MICROSOFT=m
-+CONFIG_HID_MONTEREY=m
-+CONFIG_HID_MULTITOUCH=m
-+CONFIG_HID_NTRIG=m
-+CONFIG_HID_ORTEK=m
-+CONFIG_HID_PANTHERLORD=m
-+CONFIG_HID_PETALYNX=m
-+CONFIG_HID_PICOLCD=m
-+CONFIG_HID_ROCCAT=m
-+CONFIG_HID_SAMSUNG=m
-+CONFIG_HID_SONY=m
-+CONFIG_HID_SPEEDLINK=m
-+CONFIG_HID_SUNPLUS=m
-+CONFIG_HID_GREENASIA=m
-+CONFIG_HID_SMARTJOYPLUS=m
-+CONFIG_HID_TOPSEED=m
-+CONFIG_HID_THINGM=m
-+CONFIG_HID_THRUSTMASTER=m
-+CONFIG_HID_WACOM=m
-+CONFIG_HID_WIIMOTE=m
-+CONFIG_HID_XINMO=m
-+CONFIG_HID_ZEROPLUS=m
-+CONFIG_HID_ZYDACRON=m
-+CONFIG_HID_PID=y
-+CONFIG_USB_HIDDEV=y
-+CONFIG_USB=y
-+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
-+CONFIG_USB_MON=m
-+CONFIG_USB_DWCOTG=y
-+CONFIG_USB_PRINTER=m
-+CONFIG_USB_STORAGE=y
-+CONFIG_USB_STORAGE_REALTEK=m
-+CONFIG_USB_STORAGE_DATAFAB=m
-+CONFIG_USB_STORAGE_FREECOM=m
-+CONFIG_USB_STORAGE_ISD200=m
-+CONFIG_USB_STORAGE_USBAT=m
-+CONFIG_USB_STORAGE_SDDR09=m
-+CONFIG_USB_STORAGE_SDDR55=m
-+CONFIG_USB_STORAGE_JUMPSHOT=m
-+CONFIG_USB_STORAGE_ALAUDA=m
-+CONFIG_USB_STORAGE_ONETOUCH=m
-+CONFIG_USB_STORAGE_KARMA=m
-+CONFIG_USB_STORAGE_CYPRESS_ATACB=m
-+CONFIG_USB_STORAGE_ENE_UB6250=m
-+CONFIG_USB_MDC800=m
-+CONFIG_USB_MICROTEK=m
-+CONFIG_USBIP_CORE=m
-+CONFIG_USBIP_VHCI_HCD=m
-+CONFIG_USBIP_HOST=m
-+CONFIG_USB_DWC2=m
-+CONFIG_USB_SERIAL=m
-+CONFIG_USB_SERIAL_GENERIC=y
-+CONFIG_USB_SERIAL_AIRCABLE=m
-+CONFIG_USB_SERIAL_ARK3116=m
-+CONFIG_USB_SERIAL_BELKIN=m
-+CONFIG_USB_SERIAL_CH341=m
-+CONFIG_USB_SERIAL_WHITEHEAT=m
-+CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
-+CONFIG_USB_SERIAL_CP210X=m
-+CONFIG_USB_SERIAL_CYPRESS_M8=m
-+CONFIG_USB_SERIAL_EMPEG=m
-+CONFIG_USB_SERIAL_FTDI_SIO=m
-+CONFIG_USB_SERIAL_VISOR=m
-+CONFIG_USB_SERIAL_IPAQ=m
-+CONFIG_USB_SERIAL_IR=m
-+CONFIG_USB_SERIAL_EDGEPORT=m
-+CONFIG_USB_SERIAL_EDGEPORT_TI=m
-+CONFIG_USB_SERIAL_F81232=m
-+CONFIG_USB_SERIAL_GARMIN=m
-+CONFIG_USB_SERIAL_IPW=m
-+CONFIG_USB_SERIAL_IUU=m
-+CONFIG_USB_SERIAL_KEYSPAN_PDA=m
-+CONFIG_USB_SERIAL_KEYSPAN=m
-+CONFIG_USB_SERIAL_KLSI=m
-+CONFIG_USB_SERIAL_KOBIL_SCT=m
-+CONFIG_USB_SERIAL_MCT_U232=m
-+CONFIG_USB_SERIAL_METRO=m
-+CONFIG_USB_SERIAL_MOS7720=m
-+CONFIG_USB_SERIAL_MOS7840=m
-+CONFIG_USB_SERIAL_NAVMAN=m
-+CONFIG_USB_SERIAL_PL2303=m
-+CONFIG_USB_SERIAL_OTI6858=m
-+CONFIG_USB_SERIAL_QCAUX=m
-+CONFIG_USB_SERIAL_QUALCOMM=m
-+CONFIG_USB_SERIAL_SPCP8X5=m
-+CONFIG_USB_SERIAL_SAFE=m
-+CONFIG_USB_SERIAL_SIERRAWIRELESS=m
-+CONFIG_USB_SERIAL_SYMBOL=m
-+CONFIG_USB_SERIAL_TI=m
-+CONFIG_USB_SERIAL_CYBERJACK=m
-+CONFIG_USB_SERIAL_XIRCOM=m
-+CONFIG_USB_SERIAL_OPTION=m
-+CONFIG_USB_SERIAL_OMNINET=m
-+CONFIG_USB_SERIAL_OPTICON=m
-+CONFIG_USB_SERIAL_XSENS_MT=m
-+CONFIG_USB_SERIAL_WISHBONE=m
-+CONFIG_USB_SERIAL_SSU100=m
-+CONFIG_USB_SERIAL_QT2=m
-+CONFIG_USB_SERIAL_DEBUG=m
-+CONFIG_USB_EMI62=m
-+CONFIG_USB_EMI26=m
-+CONFIG_USB_ADUTUX=m
-+CONFIG_USB_SEVSEG=m
-+CONFIG_USB_RIO500=m
-+CONFIG_USB_LEGOTOWER=m
-+CONFIG_USB_LCD=m
-+CONFIG_USB_LED=m
-+CONFIG_USB_CYPRESS_CY7C63=m
-+CONFIG_USB_CYTHERM=m
-+CONFIG_USB_IDMOUSE=m
-+CONFIG_USB_FTDI_ELAN=m
-+CONFIG_USB_APPLEDISPLAY=m
-+CONFIG_USB_LD=m
-+CONFIG_USB_TRANCEVIBRATOR=m
-+CONFIG_USB_IOWARRIOR=m
-+CONFIG_USB_TEST=m
-+CONFIG_USB_ISIGHTFW=m
-+CONFIG_USB_YUREX=m
-+CONFIG_USB_ATM=m
-+CONFIG_USB_SPEEDTOUCH=m
-+CONFIG_USB_CXACRU=m
-+CONFIG_USB_UEAGLEATM=m
-+CONFIG_USB_XUSBATM=m
-+CONFIG_USB_GADGET=m
-+CONFIG_USB_ZERO=m
-+CONFIG_USB_AUDIO=m
-+CONFIG_USB_ETH=m
-+CONFIG_USB_GADGETFS=m
-+CONFIG_USB_MASS_STORAGE=m
-+CONFIG_USB_G_SERIAL=m
-+CONFIG_USB_MIDI_GADGET=m
-+CONFIG_USB_G_PRINTER=m
-+CONFIG_USB_CDC_COMPOSITE=m
-+CONFIG_USB_G_ACM_MS=m
-+CONFIG_USB_G_MULTI=m
-+CONFIG_USB_G_HID=m
-+CONFIG_USB_G_WEBCAM=m
-+CONFIG_MMC=y
-+CONFIG_MMC_BLOCK_MINORS=32
-+CONFIG_MMC_BCM2835=y
-+CONFIG_MMC_BCM2835_DMA=y
-+CONFIG_MMC_BCM2835_SDHOST=y
-+CONFIG_MMC_SDHCI=y
-+CONFIG_MMC_SDHCI_PLTFM=y
-+CONFIG_MMC_SPI=m
-+CONFIG_LEDS_CLASS=y
-+CONFIG_LEDS_GPIO=y
-+CONFIG_LEDS_TRIGGER_TIMER=y
-+CONFIG_LEDS_TRIGGER_ONESHOT=y
-+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
-+CONFIG_LEDS_TRIGGER_BACKLIGHT=y
-+CONFIG_LEDS_TRIGGER_CPU=y
-+CONFIG_LEDS_TRIGGER_GPIO=y
-+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
-+CONFIG_LEDS_TRIGGER_TRANSIENT=m
-+CONFIG_LEDS_TRIGGER_CAMERA=m
-+CONFIG_LEDS_TRIGGER_INPUT=y
-+CONFIG_RTC_CLASS=y
-+# CONFIG_RTC_HCTOSYS is not set
-+CONFIG_RTC_DRV_DS1307=m
-+CONFIG_RTC_DRV_DS1374=m
-+CONFIG_RTC_DRV_DS1672=m
-+CONFIG_RTC_DRV_DS3232=m
-+CONFIG_RTC_DRV_MAX6900=m
-+CONFIG_RTC_DRV_RS5C372=m
-+CONFIG_RTC_DRV_ISL1208=m
-+CONFIG_RTC_DRV_ISL12022=m
-+CONFIG_RTC_DRV_ISL12057=m
-+CONFIG_RTC_DRV_X1205=m
-+CONFIG_RTC_DRV_PCF2127=m
-+CONFIG_RTC_DRV_PCF8523=m
-+CONFIG_RTC_DRV_PCF8563=m
-+CONFIG_RTC_DRV_PCF8583=m
-+CONFIG_RTC_DRV_M41T80=m
-+CONFIG_RTC_DRV_BQ32K=m
-+CONFIG_RTC_DRV_S35390A=m
-+CONFIG_RTC_DRV_FM3130=m
-+CONFIG_RTC_DRV_RX8581=m
-+CONFIG_RTC_DRV_RX8025=m
-+CONFIG_RTC_DRV_EM3027=m
-+CONFIG_RTC_DRV_RV3029C2=m
-+CONFIG_RTC_DRV_M41T93=m
-+CONFIG_RTC_DRV_M41T94=m
-+CONFIG_RTC_DRV_DS1305=m
-+CONFIG_RTC_DRV_DS1390=m
-+CONFIG_RTC_DRV_MAX6902=m
-+CONFIG_RTC_DRV_R9701=m
-+CONFIG_RTC_DRV_RS5C348=m
-+CONFIG_RTC_DRV_DS3234=m
-+CONFIG_RTC_DRV_PCF2123=m
-+CONFIG_RTC_DRV_RX4581=m
-+CONFIG_DMADEVICES=y
-+CONFIG_DMA_BCM2835=y
-+CONFIG_DMA_BCM2708=y
-+CONFIG_UIO=m
-+CONFIG_UIO_PDRV_GENIRQ=m
-+CONFIG_STAGING=y
-+CONFIG_PRISM2_USB=m
-+CONFIG_R8712U=m
-+CONFIG_R8188EU=m
-+CONFIG_R8723AU=m
-+CONFIG_VT6656=m
-+CONFIG_SPEAKUP=m
-+CONFIG_SPEAKUP_SYNTH_SOFT=m
-+CONFIG_STAGING_MEDIA=y
-+CONFIG_LIRC_STAGING=y
-+CONFIG_LIRC_IMON=m
-+CONFIG_LIRC_RPI=m
-+CONFIG_LIRC_SASEM=m
-+CONFIG_LIRC_SERIAL=m
-+CONFIG_FB_TFT=m
-+CONFIG_FB_TFT_AGM1264K_FL=m
-+CONFIG_FB_TFT_BD663474=m
-+CONFIG_FB_TFT_HX8340BN=m
-+CONFIG_FB_TFT_HX8347D=m
-+CONFIG_FB_TFT_HX8353D=m
-+CONFIG_FB_TFT_ILI9163=m
-+CONFIG_FB_TFT_ILI9320=m
-+CONFIG_FB_TFT_ILI9325=m
-+CONFIG_FB_TFT_ILI9340=m
-+CONFIG_FB_TFT_ILI9341=m
-+CONFIG_FB_TFT_ILI9481=m
-+CONFIG_FB_TFT_ILI9486=m
-+CONFIG_FB_TFT_PCD8544=m
-+CONFIG_FB_TFT_RA8875=m
-+CONFIG_FB_TFT_S6D02A1=m
-+CONFIG_FB_TFT_S6D1121=m
-+CONFIG_FB_TFT_SSD1289=m
-+CONFIG_FB_TFT_SSD1306=m
-+CONFIG_FB_TFT_SSD1331=m
-+CONFIG_FB_TFT_SSD1351=m
-+CONFIG_FB_TFT_ST7735R=m
-+CONFIG_FB_TFT_TINYLCD=m
-+CONFIG_FB_TFT_TLS8204=m
-+CONFIG_FB_TFT_UC1701=m
-+CONFIG_FB_TFT_UPD161704=m
-+CONFIG_FB_TFT_WATTEROTT=m
-+CONFIG_FB_FLEX=m
-+CONFIG_FB_TFT_FBTFT_DEVICE=m
-+CONFIG_MAILBOX=y
-+CONFIG_BCM2835_MBOX=y
-+# CONFIG_IOMMU_SUPPORT is not set
-+CONFIG_EXTCON=m
-+CONFIG_EXTCON_ARIZONA=m
-+CONFIG_IIO=m
-+CONFIG_IIO_BUFFER=y
-+CONFIG_IIO_BUFFER_CB=m
-+CONFIG_IIO_KFIFO_BUF=m
-+CONFIG_MCP320X=m
-+CONFIG_DHT11=m
-+CONFIG_PWM_BCM2835=m
-+CONFIG_RASPBERRYPI_FIRMWARE=y
-+CONFIG_EXT4_FS=y
-+CONFIG_EXT4_FS_POSIX_ACL=y
-+CONFIG_EXT4_FS_SECURITY=y
-+CONFIG_REISERFS_FS=m
-+CONFIG_REISERFS_FS_XATTR=y
-+CONFIG_REISERFS_FS_POSIX_ACL=y
-+CONFIG_REISERFS_FS_SECURITY=y
-+CONFIG_JFS_FS=m
-+CONFIG_JFS_POSIX_ACL=y
-+CONFIG_JFS_SECURITY=y
-+CONFIG_JFS_STATISTICS=y
-+CONFIG_XFS_FS=m
-+CONFIG_XFS_QUOTA=y
-+CONFIG_XFS_POSIX_ACL=y
-+CONFIG_XFS_RT=y
-+CONFIG_GFS2_FS=m
-+CONFIG_OCFS2_FS=m
-+CONFIG_BTRFS_FS=m
-+CONFIG_BTRFS_FS_POSIX_ACL=y
-+CONFIG_NILFS2_FS=m
-+CONFIG_F2FS_FS=y
-+CONFIG_FANOTIFY=y
-+CONFIG_QFMT_V1=m
-+CONFIG_QFMT_V2=m
-+CONFIG_AUTOFS4_FS=y
-+CONFIG_FUSE_FS=m
-+CONFIG_CUSE=m
-+CONFIG_OVERLAY_FS=m
-+CONFIG_FSCACHE=y
-+CONFIG_FSCACHE_STATS=y
-+CONFIG_FSCACHE_HISTOGRAM=y
-+CONFIG_CACHEFILES=y
-+CONFIG_ISO9660_FS=m
-+CONFIG_JOLIET=y
-+CONFIG_ZISOFS=y
-+CONFIG_UDF_FS=m
-+CONFIG_MSDOS_FS=y
-+CONFIG_VFAT_FS=y
-+CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
-+CONFIG_NTFS_FS=m
-+CONFIG_NTFS_RW=y
-+CONFIG_TMPFS=y
-+CONFIG_TMPFS_POSIX_ACL=y
-+CONFIG_CONFIGFS_FS=y
-+CONFIG_ECRYPT_FS=m
-+CONFIG_HFS_FS=m
-+CONFIG_HFSPLUS_FS=m
-+CONFIG_JFFS2_FS=m
-+CONFIG_JFFS2_SUMMARY=y
-+CONFIG_UBIFS_FS=m
-+CONFIG_SQUASHFS=m
-+CONFIG_SQUASHFS_XATTR=y
-+CONFIG_SQUASHFS_LZO=y
-+CONFIG_SQUASHFS_XZ=y
-+CONFIG_NFS_FS=y
-+CONFIG_NFS_V3_ACL=y
-+CONFIG_NFS_V4=y
-+CONFIG_NFS_SWAP=y
-+CONFIG_ROOT_NFS=y
-+CONFIG_NFS_FSCACHE=y
-+CONFIG_NFSD=m
-+CONFIG_NFSD_V3_ACL=y
-+CONFIG_NFSD_V4=y
-+CONFIG_CIFS=m
-+CONFIG_CIFS_WEAK_PW_HASH=y
-+CONFIG_CIFS_UPCALL=y
-+CONFIG_CIFS_XATTR=y
-+CONFIG_CIFS_POSIX=y
-+CONFIG_CIFS_ACL=y
-+CONFIG_CIFS_DFS_UPCALL=y
-+CONFIG_CIFS_SMB2=y
-+CONFIG_CIFS_FSCACHE=y
-+CONFIG_9P_FS=m
-+CONFIG_9P_FS_POSIX_ACL=y
-+CONFIG_NLS_DEFAULT="utf8"
-+CONFIG_NLS_CODEPAGE_437=y
-+CONFIG_NLS_CODEPAGE_737=m
-+CONFIG_NLS_CODEPAGE_775=m
-+CONFIG_NLS_CODEPAGE_850=m
-+CONFIG_NLS_CODEPAGE_852=m
-+CONFIG_NLS_CODEPAGE_855=m
-+CONFIG_NLS_CODEPAGE_857=m
-+CONFIG_NLS_CODEPAGE_860=m
-+CONFIG_NLS_CODEPAGE_861=m
-+CONFIG_NLS_CODEPAGE_862=m
-+CONFIG_NLS_CODEPAGE_863=m
-+CONFIG_NLS_CODEPAGE_864=m
-+CONFIG_NLS_CODEPAGE_865=m
-+CONFIG_NLS_CODEPAGE_866=m
-+CONFIG_NLS_CODEPAGE_869=m
-+CONFIG_NLS_CODEPAGE_936=m
-+CONFIG_NLS_CODEPAGE_950=m
-+CONFIG_NLS_CODEPAGE_932=m
-+CONFIG_NLS_CODEPAGE_949=m
-+CONFIG_NLS_CODEPAGE_874=m
-+CONFIG_NLS_ISO8859_8=m
-+CONFIG_NLS_CODEPAGE_1250=m
-+CONFIG_NLS_CODEPAGE_1251=m
-+CONFIG_NLS_ASCII=y
-+CONFIG_NLS_ISO8859_1=m
-+CONFIG_NLS_ISO8859_2=m
-+CONFIG_NLS_ISO8859_3=m
-+CONFIG_NLS_ISO8859_4=m
-+CONFIG_NLS_ISO8859_5=m
-+CONFIG_NLS_ISO8859_6=m
-+CONFIG_NLS_ISO8859_7=m
-+CONFIG_NLS_ISO8859_9=m
-+CONFIG_NLS_ISO8859_13=m
-+CONFIG_NLS_ISO8859_14=m
-+CONFIG_NLS_ISO8859_15=m
-+CONFIG_NLS_KOI8_R=m
-+CONFIG_NLS_KOI8_U=m
-+CONFIG_DLM=m
-+CONFIG_PRINTK_TIME=y
-+CONFIG_BOOT_PRINTK_DELAY=y
-+CONFIG_DEBUG_MEMORY_INIT=y
-+CONFIG_DETECT_HUNG_TASK=y
-+CONFIG_TIMER_STATS=y
-+CONFIG_LATENCYTOP=y
-+CONFIG_IRQSOFF_TRACER=y
-+CONFIG_SCHED_TRACER=y
-+CONFIG_STACK_TRACER=y
-+CONFIG_BLK_DEV_IO_TRACE=y
-+# CONFIG_KPROBE_EVENT is not set
-+CONFIG_FUNCTION_PROFILER=y
-+CONFIG_KGDB=y
-+CONFIG_KGDB_KDB=y
-+CONFIG_KDB_KEYBOARD=y
-+CONFIG_CRYPTO_USER=m
-+CONFIG_CRYPTO_CRYPTD=m
-+CONFIG_CRYPTO_CBC=y
-+CONFIG_CRYPTO_CTS=m
-+CONFIG_CRYPTO_XTS=m
-+CONFIG_CRYPTO_XCBC=m
-+CONFIG_CRYPTO_SHA512=m
-+CONFIG_CRYPTO_TGR192=m
-+CONFIG_CRYPTO_WP512=m
-+CONFIG_CRYPTO_CAST5=m
-+CONFIG_CRYPTO_DES=y
-+CONFIG_CRYPTO_USER_API_SKCIPHER=m
-+# CONFIG_CRYPTO_HW is not set
-+CONFIG_ARM_CRYPTO=y
-+CONFIG_CRYPTO_SHA1_ARM=m
-+CONFIG_CRYPTO_AES_ARM=m
-+CONFIG_CRC_ITU_T=y
-+CONFIG_LIBCRC32C=y
diff --git a/target/linux/brcm2708/patches-4.4/0077-bcm2835-bcm2835_defconfig.patch b/target/linux/brcm2708/patches-4.4/0077-bcm2835-bcm2835_defconfig.patch
deleted file mode 100644
index ee4f9f5..0000000
--- a/target/linux/brcm2708/patches-4.4/0077-bcm2835-bcm2835_defconfig.patch
+++ /dev/null
@@ -1,1426 +0,0 @@
-From 6b495c9f59bac8f8c2d8198beeedc8c0bf967cc1 Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Noralf=20Tr=C3=B8nnes?= <noralf at tronnes.org>
-Date: Wed, 29 Apr 2015 17:24:02 +0200
-Subject: [PATCH] bcm2835: bcm2835_defconfig
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Some options in bcm2835_defconfig are now the default and
-some have changed. Update to keep functionality.
-
-No longer available: SCSI_MULTI_LUN and RESOURCE_COUNTERS.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-bcm2835: bcm2835_defconfig enable MMC_BCM2835
-
-Enable the downstream bcm2835-mmc driver and DMA support.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-bcm2835: bcm2835_defconfig enable BCM2708_MBOX
-
-Enable the mailbox driver.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-bcm2835: bcm2835_defconfig use FB_BCM2708
-
-Enable the bcm2708 framebuffer driver.
-Disable the simple framebuffer driver, which matches the
-device handed over by u-boot.
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-bcm2835: Merge bcm2835_defconfig with bcmrpi_defconfig
-
-These commands where used to make this commit:
-
-./scripts/diffconfig -m arch/arm/configs/bcm2835_defconfig arch/arm/configs/bcmrpi_defconfig > merge.cfg
-
-cat << EOF > filter
-CONFIG_ARCH_BCM2708
-CONFIG_BCM2708_DT
-CONFIG_ARM_PATCH_PHYS_VIRT
-CONFIG_PHYS_OFFSET
-CONFIG_CMDLINE
-CONFIG_BCM2708_WDT
-CONFIG_HW_RANDOM_BCM2708
-CONFIG_I2C_BCM2708
-CONFIG_SPI_BCM2708
-CONFIG_SND_BCM2708_SOC_I2S
-CONFIG_USB_DWCOTG
-CONFIG_LIRC_RPI
-EOF
-
-grep -F -v -f filter merge.cfg > filtered.cfg
-
-cat << EOF > added.cfg
-CONFIG_WATCHDOG=y
-CONFIG_BCM2835_WDT=y
-CONFIG_MISC_FILESYSTEMS=y
-CONFIG_SND_BCM2835_SOC_I2S=m
-EOF
-
-ARCH=arm scripts/kconfig/merge_config.sh arch/arm/configs/bcm2835_defconfig filtered.cfg added.cfg
-ARCH=arm make oldconfig
-
-ARCH=arm make savedefconfig
-cp defconfig arch/arm/configs/bcm2835_defconfig
-
-rm merge.cfg filter filtered.cfg added.cfg defconfig
-
-ARCH=arm make bcm2835_defconfig
-ARCH=arm make oldconfig
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-configs: Incorporate v4.1 dependency changes
-
-Commit 78e9b7de78bb53e8bc7f4c4a60ebacb250c0c190 added a
-dependency on TI_ST instead of selecting it, disabling:
-CONFIG_BT_WILINK=m
-CONFIG_RADIO_WL128X=m
-
-Commit 652ccae5cc4e1305fb0a4619947f9ee89d8c7f5a added a
-depency on ARM_CRYPTO, disabling:
-CONFIG_CRYPTO_SHA*_ARM*=m
-CONFIG_CRYPTO_AES_ARM*=m
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-
-Conflicts:
- arch/arm/configs/bcm2709_defconfig
-
-bcm2835: Sync bcm2835_defconfig with bcmrpi_defconfig
-
-These commands where used to make this commit:
-
-: Get changed and new config values from a merge
-./scripts/diffconfig -m arch/arm/configs/bcm2835_defconfig arch/arm/configs/bcmrpi_defconfig > merge.cfg
-
-: Remove these options
-cat << EOF > filter
-CONFIG_ARCH_BCM2708
-CONFIG_BCM2708_DT
-CONFIG_ARM_PATCH_PHYS_VIRT
-CONFIG_PHYS_OFFSET
-CONFIG_CMDLINE
-CONFIG_BCM2708_WDT
-CONFIG_HW_RANDOM_BCM2708
-CONFIG_SPI_BCM2708
-EOF
-
-: Apply filter
-grep -F -v -f filter merge.cfg > filtered.cfg
-
-: Add these options
-: watchdog contains the restart/poweroff code.
-cat << EOF > added.cfg
-CONFIG_WATCHDOG=y
-CONFIG_BCM2835_WDT=y
-CONFIG_MISC_FILESYSTEMS=y
-CONFIG_I2C_BCM2835=m
-CONFIG_SND_BCM2835_SOC_I2S=m
-EOF
-
-: Create new config
-ARCH=arm scripts/kconfig/merge_config.sh arch/arm/configs/bcm2835_defconfig filtered.cfg added.cfg
-: Verify
-ARCH=arm make oldconfig
-
-: Update bcm2835_defconfig
-ARCH=arm make savedefconfig
-cp defconfig arch/arm/configs/bcm2835_defconfig
-
-: Clean up
-rm merge.cfg filter filtered.cfg added.cfg defconfig
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
----
- arch/arm/configs/bcm2835_defconfig | 1166 +++++++++++++++++++++++++++++++++++-
- 1 file changed, 1140 insertions(+), 26 deletions(-)
-
---- a/arch/arm/configs/bcm2835_defconfig
-+++ b/arch/arm/configs/bcm2835_defconfig
-@@ -1,105 +1,1103 @@
- # CONFIG_LOCALVERSION_AUTO is not set
- CONFIG_SYSVIPC=y
-+CONFIG_POSIX_MQUEUE=y
- CONFIG_FHANDLE=y
- CONFIG_NO_HZ=y
- CONFIG_HIGH_RES_TIMERS=y
- CONFIG_BSD_PROCESS_ACCT=y
- CONFIG_BSD_PROCESS_ACCT_V3=y
-+CONFIG_TASKSTATS=y
-+CONFIG_TASK_DELAY_ACCT=y
-+CONFIG_TASK_XACCT=y
-+CONFIG_TASK_IO_ACCOUNTING=y
-+CONFIG_IKCONFIG=m
-+CONFIG_IKCONFIG_PROC=y
- CONFIG_LOG_BUF_SHIFT=18
- CONFIG_CGROUP_FREEZER=y
- CONFIG_CGROUP_DEVICE=y
- CONFIG_CPUSETS=y
- CONFIG_CGROUP_CPUACCT=y
--CONFIG_RESOURCE_COUNTERS=y
-+CONFIG_MEMCG=y
- CONFIG_CGROUP_PERF=y
- CONFIG_CFS_BANDWIDTH=y
- CONFIG_RT_GROUP_SCHED=y
-+CONFIG_BLK_CGROUP=y
- CONFIG_NAMESPACES=y
- CONFIG_SCHED_AUTOGROUP=y
--CONFIG_RELAY=y
- CONFIG_BLK_DEV_INITRD=y
--CONFIG_RD_BZIP2=y
--CONFIG_RD_LZMA=y
--CONFIG_RD_XZ=y
--CONFIG_RD_LZO=y
- CONFIG_CC_OPTIMIZE_FOR_SIZE=y
--CONFIG_KALLSYMS_ALL=y
- CONFIG_EMBEDDED=y
- # CONFIG_COMPAT_BRK is not set
- CONFIG_PROFILING=y
--CONFIG_OPROFILE=y
-+CONFIG_OPROFILE=m
-+CONFIG_KPROBES=y
- CONFIG_JUMP_LABEL=y
-+CONFIG_CC_STACKPROTECTOR_REGULAR=y
-+CONFIG_MODULES=y
-+CONFIG_MODULE_UNLOAD=y
-+CONFIG_MODVERSIONS=y
-+CONFIG_MODULE_SRCVERSION_ALL=y
-+CONFIG_BLK_DEV_THROTTLING=y
-+CONFIG_PARTITION_ADVANCED=y
-+CONFIG_MAC_PARTITION=y
-+CONFIG_CFQ_GROUP_IOSCHED=y
- CONFIG_ARCH_MULTI_V6=y
- # CONFIG_ARCH_MULTI_V7 is not set
- CONFIG_ARCH_BCM=y
- CONFIG_ARCH_BCM2835=y
--CONFIG_PREEMPT_VOLUNTARY=y
-+CONFIG_PREEMPT=y
- CONFIG_AEABI=y
-+CONFIG_OABI_COMPAT=y
- CONFIG_KSM=y
- CONFIG_CLEANCACHE=y
-+CONFIG_FRONTSWAP=y
-+CONFIG_CMA=y
-+CONFIG_ZSMALLOC=m
-+CONFIG_PGTABLE_MAPPING=y
-+CONFIG_UACCESS_WITH_MEMCPY=y
- CONFIG_SECCOMP=y
--CONFIG_CC_STACKPROTECTOR=y
-+CONFIG_ZBOOT_ROM_TEXT=0x0
-+CONFIG_ZBOOT_ROM_BSS=0x0
- CONFIG_KEXEC=y
- CONFIG_CRASH_DUMP=y
-+CONFIG_CPU_FREQ=y
-+CONFIG_CPU_FREQ_STAT=m
-+CONFIG_CPU_FREQ_STAT_DETAILS=y
-+CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE=y
-+CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
-+CONFIG_CPU_FREQ_GOV_USERSPACE=y
-+CONFIG_CPU_FREQ_GOV_ONDEMAND=y
-+CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
- CONFIG_VFP=y
- # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
-+CONFIG_BINFMT_MISC=m
- # CONFIG_SUSPEND is not set
- CONFIG_NET=y
- CONFIG_PACKET=y
- CONFIG_UNIX=y
-+CONFIG_XFRM_USER=y
-+CONFIG_NET_KEY=m
- CONFIG_INET=y
-+CONFIG_IP_MULTICAST=y
-+CONFIG_IP_ADVANCED_ROUTER=y
-+CONFIG_IP_MULTIPLE_TABLES=y
-+CONFIG_IP_ROUTE_MULTIPATH=y
-+CONFIG_IP_ROUTE_VERBOSE=y
-+CONFIG_IP_PNP=y
-+CONFIG_IP_PNP_DHCP=y
-+CONFIG_IP_PNP_RARP=y
-+CONFIG_NET_IPIP=m
-+CONFIG_NET_IPGRE_DEMUX=m
-+CONFIG_NET_IPGRE=m
-+CONFIG_IP_MROUTE=y
-+CONFIG_IP_MROUTE_MULTIPLE_TABLES=y
-+CONFIG_IP_PIMSM_V1=y
-+CONFIG_IP_PIMSM_V2=y
-+CONFIG_SYN_COOKIES=y
-+CONFIG_INET_AH=m
-+CONFIG_INET_ESP=m
-+CONFIG_INET_IPCOMP=m
-+CONFIG_INET_XFRM_MODE_TRANSPORT=m
-+CONFIG_INET_XFRM_MODE_TUNNEL=m
-+CONFIG_INET_XFRM_MODE_BEET=m
-+CONFIG_INET_LRO=m
-+CONFIG_INET_DIAG=m
-+CONFIG_INET6_AH=m
-+CONFIG_INET6_ESP=m
-+CONFIG_INET6_IPCOMP=m
-+CONFIG_IPV6_TUNNEL=m
-+CONFIG_IPV6_MULTIPLE_TABLES=y
-+CONFIG_IPV6_MROUTE=y
-+CONFIG_IPV6_MROUTE_MULTIPLE_TABLES=y
-+CONFIG_IPV6_PIMSM_V2=y
- CONFIG_NETWORK_SECMARK=y
- CONFIG_NETFILTER=y
--CONFIG_CFG80211=y
--CONFIG_MAC80211=y
-+CONFIG_NF_CONNTRACK=m
-+CONFIG_NF_CONNTRACK_ZONES=y
-+CONFIG_NF_CONNTRACK_EVENTS=y
-+CONFIG_NF_CONNTRACK_TIMESTAMP=y
-+CONFIG_NF_CT_PROTO_DCCP=m
-+CONFIG_NF_CT_PROTO_UDPLITE=m
-+CONFIG_NF_CONNTRACK_AMANDA=m
-+CONFIG_NF_CONNTRACK_FTP=m
-+CONFIG_NF_CONNTRACK_H323=m
-+CONFIG_NF_CONNTRACK_IRC=m
-+CONFIG_NF_CONNTRACK_NETBIOS_NS=m
-+CONFIG_NF_CONNTRACK_SNMP=m
-+CONFIG_NF_CONNTRACK_PPTP=m
-+CONFIG_NF_CONNTRACK_SANE=m
-+CONFIG_NF_CONNTRACK_SIP=m
-+CONFIG_NF_CONNTRACK_TFTP=m
-+CONFIG_NF_CT_NETLINK=m
-+CONFIG_NETFILTER_XT_SET=m
-+CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
-+CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
-+CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
-+CONFIG_NETFILTER_XT_TARGET_DSCP=m
-+CONFIG_NETFILTER_XT_TARGET_HMARK=m
-+CONFIG_NETFILTER_XT_TARGET_IDLETIMER=m
-+CONFIG_NETFILTER_XT_TARGET_LED=m
-+CONFIG_NETFILTER_XT_TARGET_LOG=m
-+CONFIG_NETFILTER_XT_TARGET_MARK=m
-+CONFIG_NETFILTER_XT_TARGET_NFLOG=m
-+CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
-+CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
-+CONFIG_NETFILTER_XT_TARGET_TEE=m
-+CONFIG_NETFILTER_XT_TARGET_TPROXY=m
-+CONFIG_NETFILTER_XT_TARGET_TRACE=m
-+CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
-+CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
-+CONFIG_NETFILTER_XT_MATCH_ADDRTYPE=m
-+CONFIG_NETFILTER_XT_MATCH_BPF=m
-+CONFIG_NETFILTER_XT_MATCH_CLUSTER=m
-+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
-+CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
-+CONFIG_NETFILTER_XT_MATCH_CONNLABEL=m
-+CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
-+CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
-+CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
-+CONFIG_NETFILTER_XT_MATCH_CPU=m
-+CONFIG_NETFILTER_XT_MATCH_DCCP=m
-+CONFIG_NETFILTER_XT_MATCH_DEVGROUP=m
-+CONFIG_NETFILTER_XT_MATCH_DSCP=m
-+CONFIG_NETFILTER_XT_MATCH_ESP=m
-+CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
-+CONFIG_NETFILTER_XT_MATCH_HELPER=m
-+CONFIG_NETFILTER_XT_MATCH_IPRANGE=m
-+CONFIG_NETFILTER_XT_MATCH_IPVS=m
-+CONFIG_NETFILTER_XT_MATCH_LENGTH=m
-+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
-+CONFIG_NETFILTER_XT_MATCH_MAC=m
-+CONFIG_NETFILTER_XT_MATCH_MARK=m
-+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
-+CONFIG_NETFILTER_XT_MATCH_NFACCT=m
-+CONFIG_NETFILTER_XT_MATCH_OSF=m
-+CONFIG_NETFILTER_XT_MATCH_OWNER=m
-+CONFIG_NETFILTER_XT_MATCH_POLICY=m
-+CONFIG_NETFILTER_XT_MATCH_PHYSDEV=m
-+CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
-+CONFIG_NETFILTER_XT_MATCH_QUOTA=m
-+CONFIG_NETFILTER_XT_MATCH_RATEEST=m
-+CONFIG_NETFILTER_XT_MATCH_REALM=m
-+CONFIG_NETFILTER_XT_MATCH_RECENT=m
-+CONFIG_NETFILTER_XT_MATCH_SOCKET=m
-+CONFIG_NETFILTER_XT_MATCH_STATE=m
-+CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
-+CONFIG_NETFILTER_XT_MATCH_STRING=m
-+CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
-+CONFIG_NETFILTER_XT_MATCH_TIME=m
-+CONFIG_NETFILTER_XT_MATCH_U32=m
-+CONFIG_IP_SET=m
-+CONFIG_IP_SET_BITMAP_IP=m
-+CONFIG_IP_SET_BITMAP_IPMAC=m
-+CONFIG_IP_SET_BITMAP_PORT=m
-+CONFIG_IP_SET_HASH_IP=m
-+CONFIG_IP_SET_HASH_IPPORT=m
-+CONFIG_IP_SET_HASH_IPPORTIP=m
-+CONFIG_IP_SET_HASH_IPPORTNET=m
-+CONFIG_IP_SET_HASH_NET=m
-+CONFIG_IP_SET_HASH_NETPORT=m
-+CONFIG_IP_SET_HASH_NETIFACE=m
-+CONFIG_IP_SET_LIST_SET=m
-+CONFIG_IP_VS=m
-+CONFIG_IP_VS_PROTO_TCP=y
-+CONFIG_IP_VS_PROTO_UDP=y
-+CONFIG_IP_VS_PROTO_ESP=y
-+CONFIG_IP_VS_PROTO_AH=y
-+CONFIG_IP_VS_PROTO_SCTP=y
-+CONFIG_IP_VS_RR=m
-+CONFIG_IP_VS_WRR=m
-+CONFIG_IP_VS_LC=m
-+CONFIG_IP_VS_WLC=m
-+CONFIG_IP_VS_LBLC=m
-+CONFIG_IP_VS_LBLCR=m
-+CONFIG_IP_VS_DH=m
-+CONFIG_IP_VS_SH=m
-+CONFIG_IP_VS_SED=m
-+CONFIG_IP_VS_NQ=m
-+CONFIG_IP_VS_FTP=m
-+CONFIG_IP_VS_PE_SIP=m
-+CONFIG_NF_CONNTRACK_IPV4=m
-+CONFIG_IP_NF_IPTABLES=m
-+CONFIG_IP_NF_MATCH_AH=m
-+CONFIG_IP_NF_MATCH_ECN=m
-+CONFIG_IP_NF_MATCH_TTL=m
-+CONFIG_IP_NF_FILTER=m
-+CONFIG_IP_NF_TARGET_REJECT=m
-+CONFIG_IP_NF_NAT=m
-+CONFIG_IP_NF_TARGET_MASQUERADE=m
-+CONFIG_IP_NF_TARGET_NETMAP=m
-+CONFIG_IP_NF_TARGET_REDIRECT=m
-+CONFIG_IP_NF_MANGLE=m
-+CONFIG_IP_NF_TARGET_CLUSTERIP=m
-+CONFIG_IP_NF_TARGET_ECN=m
-+CONFIG_IP_NF_TARGET_TTL=m
-+CONFIG_IP_NF_RAW=m
-+CONFIG_IP_NF_ARPTABLES=m
-+CONFIG_IP_NF_ARPFILTER=m
-+CONFIG_IP_NF_ARP_MANGLE=m
-+CONFIG_NF_CONNTRACK_IPV6=m
-+CONFIG_IP6_NF_IPTABLES=m
-+CONFIG_IP6_NF_MATCH_AH=m
-+CONFIG_IP6_NF_MATCH_EUI64=m
-+CONFIG_IP6_NF_MATCH_FRAG=m
-+CONFIG_IP6_NF_MATCH_OPTS=m
-+CONFIG_IP6_NF_MATCH_HL=m
-+CONFIG_IP6_NF_MATCH_IPV6HEADER=m
-+CONFIG_IP6_NF_MATCH_MH=m
-+CONFIG_IP6_NF_MATCH_RT=m
-+CONFIG_IP6_NF_TARGET_HL=m
-+CONFIG_IP6_NF_FILTER=m
-+CONFIG_IP6_NF_TARGET_REJECT=m
-+CONFIG_IP6_NF_MANGLE=m
-+CONFIG_IP6_NF_RAW=m
-+CONFIG_IP6_NF_NAT=m
-+CONFIG_IP6_NF_TARGET_MASQUERADE=m
-+CONFIG_IP6_NF_TARGET_NPT=m
-+CONFIG_BRIDGE_NF_EBTABLES=m
-+CONFIG_BRIDGE_EBT_BROUTE=m
-+CONFIG_BRIDGE_EBT_T_FILTER=m
-+CONFIG_BRIDGE_EBT_T_NAT=m
-+CONFIG_BRIDGE_EBT_802_3=m
-+CONFIG_BRIDGE_EBT_AMONG=m
-+CONFIG_BRIDGE_EBT_ARP=m
-+CONFIG_BRIDGE_EBT_IP=m
-+CONFIG_BRIDGE_EBT_IP6=m
-+CONFIG_BRIDGE_EBT_LIMIT=m
-+CONFIG_BRIDGE_EBT_MARK=m
-+CONFIG_BRIDGE_EBT_PKTTYPE=m
-+CONFIG_BRIDGE_EBT_STP=m
-+CONFIG_BRIDGE_EBT_VLAN=m
-+CONFIG_BRIDGE_EBT_ARPREPLY=m
-+CONFIG_BRIDGE_EBT_DNAT=m
-+CONFIG_BRIDGE_EBT_MARK_T=m
-+CONFIG_BRIDGE_EBT_REDIRECT=m
-+CONFIG_BRIDGE_EBT_SNAT=m
-+CONFIG_BRIDGE_EBT_LOG=m
-+CONFIG_BRIDGE_EBT_NFLOG=m
-+CONFIG_SCTP_COOKIE_HMAC_SHA1=y
-+CONFIG_ATM=m
-+CONFIG_L2TP=m
-+CONFIG_L2TP_V3=y
-+CONFIG_L2TP_IP=m
-+CONFIG_L2TP_ETH=m
-+CONFIG_BRIDGE=m
-+CONFIG_VLAN_8021Q=m
-+CONFIG_VLAN_8021Q_GVRP=y
-+CONFIG_ATALK=m
-+CONFIG_6LOWPAN=m
-+CONFIG_NET_SCHED=y
-+CONFIG_NET_SCH_CBQ=m
-+CONFIG_NET_SCH_HTB=m
-+CONFIG_NET_SCH_HFSC=m
-+CONFIG_NET_SCH_PRIO=m
-+CONFIG_NET_SCH_MULTIQ=m
-+CONFIG_NET_SCH_RED=m
-+CONFIG_NET_SCH_SFB=m
-+CONFIG_NET_SCH_SFQ=m
-+CONFIG_NET_SCH_TEQL=m
-+CONFIG_NET_SCH_TBF=m
-+CONFIG_NET_SCH_GRED=m
-+CONFIG_NET_SCH_DSMARK=m
-+CONFIG_NET_SCH_NETEM=m
-+CONFIG_NET_SCH_DRR=m
-+CONFIG_NET_SCH_MQPRIO=m
-+CONFIG_NET_SCH_CHOKE=m
-+CONFIG_NET_SCH_QFQ=m
-+CONFIG_NET_SCH_CODEL=m
-+CONFIG_NET_SCH_FQ_CODEL=m
-+CONFIG_NET_SCH_INGRESS=m
-+CONFIG_NET_SCH_PLUG=m
-+CONFIG_NET_CLS_BASIC=m
-+CONFIG_NET_CLS_TCINDEX=m
-+CONFIG_NET_CLS_ROUTE4=m
-+CONFIG_NET_CLS_FW=m
-+CONFIG_NET_CLS_U32=m
-+CONFIG_CLS_U32_MARK=y
-+CONFIG_NET_CLS_RSVP=m
-+CONFIG_NET_CLS_RSVP6=m
-+CONFIG_NET_CLS_FLOW=m
-+CONFIG_NET_CLS_CGROUP=m
-+CONFIG_NET_EMATCH=y
-+CONFIG_NET_EMATCH_CMP=m
-+CONFIG_NET_EMATCH_NBYTE=m
-+CONFIG_NET_EMATCH_U32=m
-+CONFIG_NET_EMATCH_META=m
-+CONFIG_NET_EMATCH_TEXT=m
-+CONFIG_NET_EMATCH_IPSET=m
-+CONFIG_NET_CLS_ACT=y
-+CONFIG_NET_ACT_POLICE=m
-+CONFIG_NET_ACT_GACT=m
-+CONFIG_GACT_PROB=y
-+CONFIG_NET_ACT_MIRRED=m
-+CONFIG_NET_ACT_IPT=m
-+CONFIG_NET_ACT_NAT=m
-+CONFIG_NET_ACT_PEDIT=m
-+CONFIG_NET_ACT_SIMP=m
-+CONFIG_NET_ACT_SKBEDIT=m
-+CONFIG_NET_ACT_CSUM=m
-+CONFIG_BATMAN_ADV=m
-+CONFIG_OPENVSWITCH=m
-+CONFIG_NET_PKTGEN=m
-+CONFIG_HAMRADIO=y
-+CONFIG_AX25=m
-+CONFIG_NETROM=m
-+CONFIG_ROSE=m
-+CONFIG_MKISS=m
-+CONFIG_6PACK=m
-+CONFIG_BPQETHER=m
-+CONFIG_BAYCOM_SER_FDX=m
-+CONFIG_BAYCOM_SER_HDX=m
-+CONFIG_YAM=m
-+CONFIG_CAN=m
-+CONFIG_CAN_VCAN=m
-+CONFIG_CAN_MCP251X=m
-+CONFIG_IRDA=m
-+CONFIG_IRLAN=m
-+CONFIG_IRNET=m
-+CONFIG_IRCOMM=m
-+CONFIG_IRDA_ULTRA=y
-+CONFIG_IRDA_CACHE_LAST_LSAP=y
-+CONFIG_IRDA_FAST_RR=y
-+CONFIG_IRTTY_SIR=m
-+CONFIG_KINGSUN_DONGLE=m
-+CONFIG_KSDAZZLE_DONGLE=m
-+CONFIG_KS959_DONGLE=m
-+CONFIG_USB_IRDA=m
-+CONFIG_SIGMATEL_FIR=m
-+CONFIG_MCS_FIR=m
-+CONFIG_BT=m
-+CONFIG_BT_RFCOMM=m
-+CONFIG_BT_RFCOMM_TTY=y
-+CONFIG_BT_BNEP=m
-+CONFIG_BT_BNEP_MC_FILTER=y
-+CONFIG_BT_BNEP_PROTO_FILTER=y
-+CONFIG_BT_HIDP=m
-+CONFIG_BT_6LOWPAN=m
-+CONFIG_BT_HCIBTUSB=m
-+CONFIG_BT_HCIBCM203X=m
-+CONFIG_BT_HCIBPA10X=m
-+CONFIG_BT_HCIBFUSB=m
-+CONFIG_BT_HCIVHCI=m
-+CONFIG_BT_MRVL=m
-+CONFIG_BT_MRVL_SDIO=m
-+CONFIG_BT_ATH3K=m
-+CONFIG_BT_WILINK=m
-+CONFIG_MAC80211=m
-+CONFIG_MAC80211_MESH=y
-+CONFIG_WIMAX=m
-+CONFIG_RFKILL=m
-+CONFIG_RFKILL_INPUT=y
-+CONFIG_NET_9P=m
-+CONFIG_NFC=m
-+CONFIG_NFC_PN533=m
- CONFIG_DEVTMPFS=y
- CONFIG_DEVTMPFS_MOUNT=y
- # CONFIG_STANDALONE is not set
-+CONFIG_DMA_CMA=y
-+CONFIG_CMA_SIZE_MBYTES=5
-+CONFIG_ZRAM=m
-+CONFIG_ZRAM_LZ4_COMPRESS=y
-+CONFIG_BLK_DEV_LOOP=y
-+CONFIG_BLK_DEV_CRYPTOLOOP=m
-+CONFIG_BLK_DEV_DRBD=m
-+CONFIG_BLK_DEV_NBD=m
-+CONFIG_BLK_DEV_RAM=y
-+CONFIG_CDROM_PKTCDVD=m
-+CONFIG_ATA_OVER_ETH=m
-+CONFIG_EEPROM_AT24=m
-+CONFIG_TI_ST=m
- CONFIG_SCSI=y
-+# CONFIG_SCSI_PROC_FS is not set
- CONFIG_BLK_DEV_SD=y
--CONFIG_SCSI_MULTI_LUN=y
-+CONFIG_CHR_DEV_ST=m
-+CONFIG_CHR_DEV_OSST=m
-+CONFIG_BLK_DEV_SR=m
-+CONFIG_CHR_DEV_SG=m
- CONFIG_SCSI_CONSTANTS=y
- CONFIG_SCSI_SCAN_ASYNC=y
-+CONFIG_SCSI_ISCSI_ATTRS=y
-+CONFIG_ISCSI_TCP=m
-+CONFIG_ISCSI_BOOT_SYSFS=m
-+CONFIG_MD=y
-+CONFIG_MD_LINEAR=m
-+CONFIG_MD_RAID0=m
-+CONFIG_BLK_DEV_DM=m
-+CONFIG_DM_CRYPT=m
-+CONFIG_DM_SNAPSHOT=m
-+CONFIG_DM_MIRROR=m
-+CONFIG_DM_LOG_USERSPACE=m
-+CONFIG_DM_RAID=m
-+CONFIG_DM_ZERO=m
-+CONFIG_DM_DELAY=m
- CONFIG_NETDEVICES=y
-+CONFIG_BONDING=m
-+CONFIG_DUMMY=m
-+CONFIG_IFB=m
-+CONFIG_MACVLAN=m
-+CONFIG_NETCONSOLE=m
-+CONFIG_TUN=m
-+CONFIG_VETH=m
-+CONFIG_ENC28J60=m
-+CONFIG_MDIO_BITBANG=m
-+CONFIG_PPP=m
-+CONFIG_PPP_BSDCOMP=m
-+CONFIG_PPP_DEFLATE=m
-+CONFIG_PPP_FILTER=y
-+CONFIG_PPP_MPPE=m
-+CONFIG_PPP_MULTILINK=y
-+CONFIG_PPPOATM=m
-+CONFIG_PPPOE=m
-+CONFIG_PPPOL2TP=m
-+CONFIG_PPP_ASYNC=m
-+CONFIG_PPP_SYNC_TTY=m
-+CONFIG_SLIP=m
-+CONFIG_SLIP_COMPRESSED=y
-+CONFIG_SLIP_SMART=y
-+CONFIG_USB_CATC=m
-+CONFIG_USB_KAWETH=m
-+CONFIG_USB_PEGASUS=m
-+CONFIG_USB_RTL8150=m
-+CONFIG_USB_RTL8152=m
- CONFIG_USB_USBNET=y
-+CONFIG_USB_NET_AX8817X=m
-+CONFIG_USB_NET_AX88179_178A=m
-+CONFIG_USB_NET_CDCETHER=m
-+CONFIG_USB_NET_CDC_EEM=m
-+CONFIG_USB_NET_CDC_NCM=m
-+CONFIG_USB_NET_HUAWEI_CDC_NCM=m
-+CONFIG_USB_NET_CDC_MBIM=m
-+CONFIG_USB_NET_DM9601=m
-+CONFIG_USB_NET_SR9700=m
-+CONFIG_USB_NET_SR9800=m
-+CONFIG_USB_NET_SMSC75XX=m
- CONFIG_USB_NET_SMSC95XX=y
--CONFIG_ZD1211RW=y
--CONFIG_INPUT_EVDEV=y
-+CONFIG_USB_NET_GL620A=m
-+CONFIG_USB_NET_NET1080=m
-+CONFIG_USB_NET_PLUSB=m
-+CONFIG_USB_NET_MCS7830=m
-+CONFIG_USB_NET_CDC_SUBSET=m
-+CONFIG_USB_ALI_M5632=y
-+CONFIG_USB_AN2720=y
-+CONFIG_USB_EPSON2888=y
-+CONFIG_USB_KC2190=y
-+CONFIG_USB_NET_ZAURUS=m
-+CONFIG_USB_NET_CX82310_ETH=m
-+CONFIG_USB_NET_KALMIA=m
-+CONFIG_USB_NET_QMI_WWAN=m
-+CONFIG_USB_HSO=m
-+CONFIG_USB_NET_INT51X1=m
-+CONFIG_USB_IPHETH=m
-+CONFIG_USB_SIERRA_NET=m
-+CONFIG_USB_VL600=m
-+CONFIG_LIBERTAS_THINFIRM=m
-+CONFIG_LIBERTAS_THINFIRM_USB=m
-+CONFIG_AT76C50X_USB=m
-+CONFIG_USB_ZD1201=m
-+CONFIG_USB_NET_RNDIS_WLAN=m
-+CONFIG_RTL8187=m
-+CONFIG_MAC80211_HWSIM=m
-+CONFIG_ATH_CARDS=m
-+CONFIG_ATH9K=m
-+CONFIG_ATH9K_HTC=m
-+CONFIG_CARL9170=m
-+CONFIG_ATH6KL=m
-+CONFIG_ATH6KL_USB=m
-+CONFIG_AR5523=m
-+CONFIG_B43=m
-+# CONFIG_B43_PHY_N is not set
-+CONFIG_B43LEGACY=m
-+CONFIG_BRCMFMAC=m
-+CONFIG_BRCMFMAC_USB=y
-+CONFIG_HOSTAP=m
-+CONFIG_LIBERTAS=m
-+CONFIG_LIBERTAS_USB=m
-+CONFIG_LIBERTAS_SDIO=m
-+CONFIG_P54_COMMON=m
-+CONFIG_P54_USB=m
-+CONFIG_RT2X00=m
-+CONFIG_RT2500USB=m
-+CONFIG_RT73USB=m
-+CONFIG_RT2800USB=m
-+CONFIG_RT2800USB_RT3573=y
-+CONFIG_RT2800USB_RT53XX=y
-+CONFIG_RT2800USB_RT55XX=y
-+CONFIG_RT2800USB_UNKNOWN=y
-+CONFIG_WL_MEDIATEK=y
-+CONFIG_MT7601U=m
-+CONFIG_RTL8192CU=m
-+CONFIG_ZD1211RW=m
-+CONFIG_MWIFIEX=m
-+CONFIG_MWIFIEX_SDIO=m
-+CONFIG_WIMAX_I2400M_USB=m
-+CONFIG_INPUT_POLLDEV=m
-+# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-+CONFIG_INPUT_JOYDEV=m
-+CONFIG_INPUT_EVDEV=m
-+# CONFIG_KEYBOARD_ATKBD is not set
-+CONFIG_KEYBOARD_GPIO=m
-+# CONFIG_INPUT_MOUSE is not set
-+CONFIG_INPUT_JOYSTICK=y
-+CONFIG_JOYSTICK_IFORCE=m
-+CONFIG_JOYSTICK_IFORCE_USB=y
-+CONFIG_JOYSTICK_XPAD=m
-+CONFIG_JOYSTICK_XPAD_FF=y
-+CONFIG_JOYSTICK_RPISENSE=m
-+CONFIG_INPUT_TOUCHSCREEN=y
-+CONFIG_TOUCHSCREEN_ADS7846=m
-+CONFIG_TOUCHSCREEN_EGALAX=m
-+CONFIG_TOUCHSCREEN_RPI_FT5406=m
-+CONFIG_TOUCHSCREEN_USB_COMPOSITE=m
-+CONFIG_TOUCHSCREEN_STMPE=m
-+CONFIG_INPUT_MISC=y
-+CONFIG_INPUT_AD714X=m
-+CONFIG_INPUT_ATI_REMOTE2=m
-+CONFIG_INPUT_KEYSPAN_REMOTE=m
-+CONFIG_INPUT_POWERMATE=m
-+CONFIG_INPUT_YEALINK=m
-+CONFIG_INPUT_CM109=m
-+CONFIG_INPUT_UINPUT=m
-+CONFIG_INPUT_GPIO_ROTARY_ENCODER=m
-+CONFIG_INPUT_ADXL34X=m
-+CONFIG_INPUT_CMA3000=m
-+CONFIG_SERIO=m
-+CONFIG_SERIO_RAW=m
-+CONFIG_GAMEPORT=m
-+CONFIG_GAMEPORT_NS558=m
-+CONFIG_GAMEPORT_L4=m
-+CONFIG_BRCM_CHAR_DRIVERS=y
-+CONFIG_BCM_VC_CMA=y
-+CONFIG_BCM_VCIO=y
-+CONFIG_BCM_VC_SM=y
-+CONFIG_DEVPTS_MULTIPLE_INSTANCES=y
- # CONFIG_LEGACY_PTYS is not set
- # CONFIG_DEVKMEM is not set
-+CONFIG_SERIAL_8250=y
-+# CONFIG_SERIAL_8250_DEPRECATED_OPTIONS is not set
-+CONFIG_SERIAL_8250_CONSOLE=y
-+# CONFIG_SERIAL_8250_DMA is not set
-+CONFIG_SERIAL_8250_NR_UARTS=1
-+CONFIG_SERIAL_8250_RUNTIME_UARTS=0
- CONFIG_SERIAL_AMBA_PL011=y
- CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
-+CONFIG_SERIAL_OF_PLATFORM=y
- CONFIG_TTY_PRINTK=y
-+CONFIG_HW_RANDOM=y
-+CONFIG_HW_RANDOM_BCM2835=m
-+CONFIG_RAW_DRIVER=y
- CONFIG_I2C=y
--CONFIG_I2C_CHARDEV=y
--CONFIG_I2C_BCM2835=y
-+CONFIG_I2C_CHARDEV=m
-+CONFIG_I2C_BCM2708=m
-+CONFIG_I2C_BCM2835=m
- CONFIG_SPI=y
--CONFIG_SPI_BCM2835=y
-+CONFIG_SPI_BCM2835=m
-+CONFIG_SPI_SPIDEV=y
-+CONFIG_PPS=m
-+CONFIG_PPS_CLIENT_LDISC=m
-+CONFIG_PPS_CLIENT_GPIO=m
- CONFIG_GPIO_SYSFS=y
-+CONFIG_GPIO_ARIZONA=m
-+CONFIG_GPIO_STMPE=y
-+CONFIG_W1=m
-+CONFIG_W1_MASTER_DS2490=m
-+CONFIG_W1_MASTER_DS2482=m
-+CONFIG_W1_MASTER_DS1WM=m
-+CONFIG_W1_MASTER_GPIO=m
-+CONFIG_W1_SLAVE_THERM=m
-+CONFIG_W1_SLAVE_SMEM=m
-+CONFIG_W1_SLAVE_DS2408=m
-+CONFIG_W1_SLAVE_DS2413=m
-+CONFIG_W1_SLAVE_DS2406=m
-+CONFIG_W1_SLAVE_DS2423=m
-+CONFIG_W1_SLAVE_DS2431=m
-+CONFIG_W1_SLAVE_DS2433=m
-+CONFIG_W1_SLAVE_DS2760=m
-+CONFIG_W1_SLAVE_DS2780=m
-+CONFIG_W1_SLAVE_DS2781=m
-+CONFIG_W1_SLAVE_DS28E04=m
-+CONFIG_W1_SLAVE_BQ27000=m
-+CONFIG_BATTERY_DS2760=m
-+CONFIG_POWER_RESET=y
-+CONFIG_POWER_RESET_GPIO=y
- # CONFIG_HWMON is not set
-+CONFIG_THERMAL=y
-+CONFIG_THERMAL_BCM2835=y
-+CONFIG_WATCHDOG=y
-+CONFIG_BCM2835_WDT=y
-+CONFIG_UCB1400_CORE=m
-+CONFIG_MFD_STMPE=y
-+CONFIG_STMPE_SPI=y
-+CONFIG_MFD_ARIZONA_I2C=m
-+CONFIG_MFD_ARIZONA_SPI=m
-+CONFIG_MFD_WM5102=y
-+CONFIG_MEDIA_SUPPORT=m
-+CONFIG_MEDIA_CAMERA_SUPPORT=y
-+CONFIG_MEDIA_ANALOG_TV_SUPPORT=y
-+CONFIG_MEDIA_DIGITAL_TV_SUPPORT=y
-+CONFIG_MEDIA_RADIO_SUPPORT=y
-+CONFIG_MEDIA_RC_SUPPORT=y
-+CONFIG_MEDIA_CONTROLLER=y
-+CONFIG_LIRC=m
-+CONFIG_RC_DEVICES=y
-+CONFIG_RC_ATI_REMOTE=m
-+CONFIG_IR_IMON=m
-+CONFIG_IR_MCEUSB=m
-+CONFIG_IR_REDRAT3=m
-+CONFIG_IR_STREAMZAP=m
-+CONFIG_IR_IGUANA=m
-+CONFIG_IR_TTUSBIR=m
-+CONFIG_RC_LOOPBACK=m
-+CONFIG_IR_GPIO_CIR=m
-+CONFIG_MEDIA_USB_SUPPORT=y
-+CONFIG_USB_VIDEO_CLASS=m
-+CONFIG_USB_M5602=m
-+CONFIG_USB_STV06XX=m
-+CONFIG_USB_GL860=m
-+CONFIG_USB_GSPCA_BENQ=m
-+CONFIG_USB_GSPCA_CONEX=m
-+CONFIG_USB_GSPCA_CPIA1=m
-+CONFIG_USB_GSPCA_DTCS033=m
-+CONFIG_USB_GSPCA_ETOMS=m
-+CONFIG_USB_GSPCA_FINEPIX=m
-+CONFIG_USB_GSPCA_JEILINJ=m
-+CONFIG_USB_GSPCA_JL2005BCD=m
-+CONFIG_USB_GSPCA_KINECT=m
-+CONFIG_USB_GSPCA_KONICA=m
-+CONFIG_USB_GSPCA_MARS=m
-+CONFIG_USB_GSPCA_MR97310A=m
-+CONFIG_USB_GSPCA_NW80X=m
-+CONFIG_USB_GSPCA_OV519=m
-+CONFIG_USB_GSPCA_OV534=m
-+CONFIG_USB_GSPCA_OV534_9=m
-+CONFIG_USB_GSPCA_PAC207=m
-+CONFIG_USB_GSPCA_PAC7302=m
-+CONFIG_USB_GSPCA_PAC7311=m
-+CONFIG_USB_GSPCA_SE401=m
-+CONFIG_USB_GSPCA_SN9C2028=m
-+CONFIG_USB_GSPCA_SN9C20X=m
-+CONFIG_USB_GSPCA_SONIXB=m
-+CONFIG_USB_GSPCA_SONIXJ=m
-+CONFIG_USB_GSPCA_SPCA500=m
-+CONFIG_USB_GSPCA_SPCA501=m
-+CONFIG_USB_GSPCA_SPCA505=m
-+CONFIG_USB_GSPCA_SPCA506=m
-+CONFIG_USB_GSPCA_SPCA508=m
-+CONFIG_USB_GSPCA_SPCA561=m
-+CONFIG_USB_GSPCA_SPCA1528=m
-+CONFIG_USB_GSPCA_SQ905=m
-+CONFIG_USB_GSPCA_SQ905C=m
-+CONFIG_USB_GSPCA_SQ930X=m
-+CONFIG_USB_GSPCA_STK014=m
-+CONFIG_USB_GSPCA_STK1135=m
-+CONFIG_USB_GSPCA_STV0680=m
-+CONFIG_USB_GSPCA_SUNPLUS=m
-+CONFIG_USB_GSPCA_T613=m
-+CONFIG_USB_GSPCA_TOPRO=m
-+CONFIG_USB_GSPCA_TV8532=m
-+CONFIG_USB_GSPCA_VC032X=m
-+CONFIG_USB_GSPCA_VICAM=m
-+CONFIG_USB_GSPCA_XIRLINK_CIT=m
-+CONFIG_USB_GSPCA_ZC3XX=m
-+CONFIG_USB_PWC=m
-+CONFIG_VIDEO_CPIA2=m
-+CONFIG_USB_ZR364XX=m
-+CONFIG_USB_STKWEBCAM=m
-+CONFIG_USB_S2255=m
-+CONFIG_VIDEO_USBTV=m
-+CONFIG_VIDEO_PVRUSB2=m
-+CONFIG_VIDEO_HDPVR=m
-+CONFIG_VIDEO_USBVISION=m
-+CONFIG_VIDEO_STK1160_COMMON=m
-+CONFIG_VIDEO_STK1160_AC97=y
-+CONFIG_VIDEO_GO7007=m
-+CONFIG_VIDEO_GO7007_USB=m
-+CONFIG_VIDEO_GO7007_USB_S2250_BOARD=m
-+CONFIG_VIDEO_AU0828=m
-+CONFIG_VIDEO_AU0828_RC=y
-+CONFIG_VIDEO_CX231XX=m
-+CONFIG_VIDEO_CX231XX_ALSA=m
-+CONFIG_VIDEO_CX231XX_DVB=m
-+CONFIG_VIDEO_TM6000=m
-+CONFIG_VIDEO_TM6000_ALSA=m
-+CONFIG_VIDEO_TM6000_DVB=m
-+CONFIG_DVB_USB=m
-+CONFIG_DVB_USB_A800=m
-+CONFIG_DVB_USB_DIBUSB_MB=m
-+CONFIG_DVB_USB_DIBUSB_MB_FAULTY=y
-+CONFIG_DVB_USB_DIBUSB_MC=m
-+CONFIG_DVB_USB_DIB0700=m
-+CONFIG_DVB_USB_UMT_010=m
-+CONFIG_DVB_USB_CXUSB=m
-+CONFIG_DVB_USB_M920X=m
-+CONFIG_DVB_USB_DIGITV=m
-+CONFIG_DVB_USB_VP7045=m
-+CONFIG_DVB_USB_VP702X=m
-+CONFIG_DVB_USB_GP8PSK=m
-+CONFIG_DVB_USB_NOVA_T_USB2=m
-+CONFIG_DVB_USB_TTUSB2=m
-+CONFIG_DVB_USB_DTT200U=m
-+CONFIG_DVB_USB_OPERA1=m
-+CONFIG_DVB_USB_AF9005=m
-+CONFIG_DVB_USB_AF9005_REMOTE=m
-+CONFIG_DVB_USB_PCTV452E=m
-+CONFIG_DVB_USB_DW2102=m
-+CONFIG_DVB_USB_CINERGY_T2=m
-+CONFIG_DVB_USB_DTV5100=m
-+CONFIG_DVB_USB_FRIIO=m
-+CONFIG_DVB_USB_AZ6027=m
-+CONFIG_DVB_USB_TECHNISAT_USB2=m
-+CONFIG_DVB_USB_V2=m
-+CONFIG_DVB_USB_AF9015=m
-+CONFIG_DVB_USB_AF9035=m
-+CONFIG_DVB_USB_ANYSEE=m
-+CONFIG_DVB_USB_AU6610=m
-+CONFIG_DVB_USB_AZ6007=m
-+CONFIG_DVB_USB_CE6230=m
-+CONFIG_DVB_USB_EC168=m
-+CONFIG_DVB_USB_GL861=m
-+CONFIG_DVB_USB_LME2510=m
-+CONFIG_DVB_USB_MXL111SF=m
-+CONFIG_DVB_USB_RTL28XXU=m
-+CONFIG_DVB_USB_DVBSKY=m
-+CONFIG_SMS_USB_DRV=m
-+CONFIG_DVB_B2C2_FLEXCOP_USB=m
-+CONFIG_DVB_AS102=m
-+CONFIG_VIDEO_EM28XX=m
-+CONFIG_VIDEO_EM28XX_V4L2=m
-+CONFIG_VIDEO_EM28XX_ALSA=m
-+CONFIG_VIDEO_EM28XX_DVB=m
-+CONFIG_V4L_PLATFORM_DRIVERS=y
-+CONFIG_VIDEO_BCM2835=y
-+CONFIG_VIDEO_BCM2835_MMAL=m
-+CONFIG_RADIO_SI470X=y
-+CONFIG_USB_SI470X=m
-+CONFIG_I2C_SI470X=m
-+CONFIG_RADIO_SI4713=m
-+CONFIG_I2C_SI4713=m
-+CONFIG_USB_MR800=m
-+CONFIG_USB_DSBR=m
-+CONFIG_RADIO_SHARK=m
-+CONFIG_RADIO_SHARK2=m
-+CONFIG_USB_KEENE=m
-+CONFIG_USB_MA901=m
-+CONFIG_RADIO_TEA5764=m
-+CONFIG_RADIO_SAA7706H=m
-+CONFIG_RADIO_TEF6862=m
-+CONFIG_RADIO_WL1273=m
-+CONFIG_RADIO_WL128X=m
-+# CONFIG_MEDIA_SUBDRV_AUTOSELECT is not set
-+CONFIG_VIDEO_UDA1342=m
-+CONFIG_VIDEO_SONY_BTF_MPX=m
-+CONFIG_VIDEO_TVP5150=m
-+CONFIG_VIDEO_TW2804=m
-+CONFIG_VIDEO_TW9903=m
-+CONFIG_VIDEO_TW9906=m
-+CONFIG_VIDEO_OV7640=m
-+CONFIG_VIDEO_MT9V011=m
- CONFIG_FB=y
--CONFIG_FB_SIMPLE=y
-+CONFIG_FB_BCM2708=y
-+CONFIG_FB_SSD1307=m
-+CONFIG_FB_RPISENSE=m
-+# CONFIG_BACKLIGHT_GENERIC is not set
-+CONFIG_BACKLIGHT_GPIO=m
- CONFIG_FRAMEBUFFER_CONSOLE=y
- CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
-+CONFIG_LOGO=y
-+# CONFIG_LOGO_LINUX_MONO is not set
-+# CONFIG_LOGO_LINUX_VGA16 is not set
-+CONFIG_SOUND=y
-+CONFIG_SND=m
-+CONFIG_SND_SEQUENCER=m
-+CONFIG_SND_SEQ_DUMMY=m
-+CONFIG_SND_MIXER_OSS=m
-+CONFIG_SND_PCM_OSS=m
-+CONFIG_SND_SEQUENCER_OSS=y
-+CONFIG_SND_HRTIMER=m
-+CONFIG_SND_DUMMY=m
-+CONFIG_SND_ALOOP=m
-+CONFIG_SND_VIRMIDI=m
-+CONFIG_SND_MTPAV=m
-+CONFIG_SND_SERIAL_U16550=m
-+CONFIG_SND_MPU401=m
-+CONFIG_SND_BCM2835=m
-+CONFIG_SND_USB_AUDIO=m
-+CONFIG_SND_USB_UA101=m
-+CONFIG_SND_USB_CAIAQ=m
-+CONFIG_SND_USB_CAIAQ_INPUT=y
-+CONFIG_SND_USB_6FIRE=m
-+CONFIG_SND_SOC=m
-+CONFIG_SND_BCM2835_SOC_I2S=m
-+CONFIG_SND_BCM2708_SOC_I2S=m
-+CONFIG_SND_BCM2708_SOC_HIFIBERRY_DAC=m
-+CONFIG_SND_BCM2708_SOC_HIFIBERRY_DACPLUS=m
-+CONFIG_SND_BCM2708_SOC_HIFIBERRY_DIGI=m
-+CONFIG_SND_BCM2708_SOC_HIFIBERRY_AMP=m
-+CONFIG_SND_BCM2708_SOC_RPI_DAC=m
-+CONFIG_SND_BCM2708_SOC_RPI_PROTO=m
-+CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC=m
-+CONFIG_SND_SOC_WM8804_I2C=m
-+CONFIG_SND_SIMPLE_CARD=m
-+CONFIG_SOUND_PRIME=m
-+CONFIG_HIDRAW=y
-+CONFIG_HID_A4TECH=m
-+CONFIG_HID_ACRUX=m
-+CONFIG_HID_APPLE=m
-+CONFIG_HID_BELKIN=m
-+CONFIG_HID_CHERRY=m
-+CONFIG_HID_CHICONY=m
-+CONFIG_HID_CYPRESS=m
-+CONFIG_HID_DRAGONRISE=m
-+CONFIG_HID_EMS_FF=m
-+CONFIG_HID_ELECOM=m
-+CONFIG_HID_ELO=m
-+CONFIG_HID_EZKEY=m
-+CONFIG_HID_HOLTEK=m
-+CONFIG_HID_KEYTOUCH=m
-+CONFIG_HID_KYE=m
-+CONFIG_HID_UCLOGIC=m
-+CONFIG_HID_WALTOP=m
-+CONFIG_HID_GYRATION=m
-+CONFIG_HID_TWINHAN=m
-+CONFIG_HID_KENSINGTON=m
-+CONFIG_HID_LCPOWER=m
-+CONFIG_HID_LOGITECH=m
-+CONFIG_HID_MAGICMOUSE=m
-+CONFIG_HID_MICROSOFT=m
-+CONFIG_HID_MONTEREY=m
-+CONFIG_HID_MULTITOUCH=m
-+CONFIG_HID_NTRIG=m
-+CONFIG_HID_ORTEK=m
-+CONFIG_HID_PANTHERLORD=m
-+CONFIG_HID_PETALYNX=m
-+CONFIG_HID_PICOLCD=m
-+CONFIG_HID_ROCCAT=m
-+CONFIG_HID_SAMSUNG=m
-+CONFIG_HID_SONY=m
-+CONFIG_HID_SPEEDLINK=m
-+CONFIG_HID_SUNPLUS=m
-+CONFIG_HID_GREENASIA=m
-+CONFIG_HID_SMARTJOYPLUS=m
-+CONFIG_HID_TOPSEED=m
-+CONFIG_HID_THINGM=m
-+CONFIG_HID_THRUSTMASTER=m
-+CONFIG_HID_WACOM=m
-+CONFIG_HID_WIIMOTE=m
-+CONFIG_HID_XINMO=m
-+CONFIG_HID_ZEROPLUS=m
-+CONFIG_HID_ZYDACRON=m
-+CONFIG_HID_PID=y
-+CONFIG_USB_HIDDEV=y
- CONFIG_USB=y
-+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
-+CONFIG_USB_MON=m
-+CONFIG_USB_DWCOTG=y
-+CONFIG_USB_PRINTER=m
- CONFIG_USB_STORAGE=y
-+CONFIG_USB_STORAGE_REALTEK=m
-+CONFIG_USB_STORAGE_DATAFAB=m
-+CONFIG_USB_STORAGE_FREECOM=m
-+CONFIG_USB_STORAGE_ISD200=m
-+CONFIG_USB_STORAGE_USBAT=m
-+CONFIG_USB_STORAGE_SDDR09=m
-+CONFIG_USB_STORAGE_SDDR55=m
-+CONFIG_USB_STORAGE_JUMPSHOT=m
-+CONFIG_USB_STORAGE_ALAUDA=m
-+CONFIG_USB_STORAGE_ONETOUCH=m
-+CONFIG_USB_STORAGE_KARMA=m
-+CONFIG_USB_STORAGE_CYPRESS_ATACB=m
-+CONFIG_USB_STORAGE_ENE_UB6250=m
-+CONFIG_USB_MDC800=m
-+CONFIG_USB_MICROTEK=m
-+CONFIG_USBIP_CORE=m
-+CONFIG_USBIP_VHCI_HCD=m
-+CONFIG_USBIP_HOST=m
-+CONFIG_USB_DWC2=y
-+CONFIG_USB_SERIAL=m
-+CONFIG_USB_SERIAL_GENERIC=y
-+CONFIG_USB_SERIAL_AIRCABLE=m
-+CONFIG_USB_SERIAL_ARK3116=m
-+CONFIG_USB_SERIAL_BELKIN=m
-+CONFIG_USB_SERIAL_CH341=m
-+CONFIG_USB_SERIAL_WHITEHEAT=m
-+CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
-+CONFIG_USB_SERIAL_CP210X=m
-+CONFIG_USB_SERIAL_CYPRESS_M8=m
-+CONFIG_USB_SERIAL_EMPEG=m
-+CONFIG_USB_SERIAL_FTDI_SIO=m
-+CONFIG_USB_SERIAL_VISOR=m
-+CONFIG_USB_SERIAL_IPAQ=m
-+CONFIG_USB_SERIAL_IR=m
-+CONFIG_USB_SERIAL_EDGEPORT=m
-+CONFIG_USB_SERIAL_EDGEPORT_TI=m
-+CONFIG_USB_SERIAL_F81232=m
-+CONFIG_USB_SERIAL_GARMIN=m
-+CONFIG_USB_SERIAL_IPW=m
-+CONFIG_USB_SERIAL_IUU=m
-+CONFIG_USB_SERIAL_KEYSPAN_PDA=m
-+CONFIG_USB_SERIAL_KEYSPAN=m
-+CONFIG_USB_SERIAL_KLSI=m
-+CONFIG_USB_SERIAL_KOBIL_SCT=m
-+CONFIG_USB_SERIAL_MCT_U232=m
-+CONFIG_USB_SERIAL_METRO=m
-+CONFIG_USB_SERIAL_MOS7720=m
-+CONFIG_USB_SERIAL_MOS7840=m
-+CONFIG_USB_SERIAL_NAVMAN=m
-+CONFIG_USB_SERIAL_PL2303=m
-+CONFIG_USB_SERIAL_OTI6858=m
-+CONFIG_USB_SERIAL_QCAUX=m
-+CONFIG_USB_SERIAL_QUALCOMM=m
-+CONFIG_USB_SERIAL_SPCP8X5=m
-+CONFIG_USB_SERIAL_SAFE=m
-+CONFIG_USB_SERIAL_SIERRAWIRELESS=m
-+CONFIG_USB_SERIAL_SYMBOL=m
-+CONFIG_USB_SERIAL_TI=m
-+CONFIG_USB_SERIAL_CYBERJACK=m
-+CONFIG_USB_SERIAL_XIRCOM=m
-+CONFIG_USB_SERIAL_OPTION=m
-+CONFIG_USB_SERIAL_OMNINET=m
-+CONFIG_USB_SERIAL_OPTICON=m
-+CONFIG_USB_SERIAL_XSENS_MT=m
-+CONFIG_USB_SERIAL_WISHBONE=m
-+CONFIG_USB_SERIAL_SSU100=m
-+CONFIG_USB_SERIAL_QT2=m
-+CONFIG_USB_SERIAL_DEBUG=m
-+CONFIG_USB_EMI62=m
-+CONFIG_USB_EMI26=m
-+CONFIG_USB_ADUTUX=m
-+CONFIG_USB_SEVSEG=m
-+CONFIG_USB_RIO500=m
-+CONFIG_USB_LEGOTOWER=m
-+CONFIG_USB_LCD=m
-+CONFIG_USB_LED=m
-+CONFIG_USB_CYPRESS_CY7C63=m
-+CONFIG_USB_CYTHERM=m
-+CONFIG_USB_IDMOUSE=m
-+CONFIG_USB_FTDI_ELAN=m
-+CONFIG_USB_APPLEDISPLAY=m
-+CONFIG_USB_LD=m
-+CONFIG_USB_TRANCEVIBRATOR=m
-+CONFIG_USB_IOWARRIOR=m
-+CONFIG_USB_TEST=m
-+CONFIG_USB_ISIGHTFW=m
-+CONFIG_USB_YUREX=m
-+CONFIG_USB_ATM=m
-+CONFIG_USB_SPEEDTOUCH=m
-+CONFIG_USB_CXACRU=m
-+CONFIG_USB_UEAGLEATM=m
-+CONFIG_USB_XUSBATM=m
- CONFIG_MMC=y
-+CONFIG_MMC_BLOCK_MINORS=32
-+CONFIG_MMC_BCM2835=y
-+CONFIG_MMC_BCM2835_DMA=y
-+CONFIG_MMC_BCM2835_SDHOST=y
- CONFIG_MMC_SDHCI=y
- CONFIG_MMC_SDHCI_PLTFM=y
- CONFIG_MMC_SDHCI_BCM2835=y
-+CONFIG_MMC_SPI=m
-+CONFIG_LEDS_CLASS=y
- CONFIG_LEDS_GPIO=y
- CONFIG_LEDS_TRIGGER_TIMER=y
- CONFIG_LEDS_TRIGGER_ONESHOT=y
- CONFIG_LEDS_TRIGGER_HEARTBEAT=y
-+CONFIG_LEDS_TRIGGER_BACKLIGHT=y
- CONFIG_LEDS_TRIGGER_CPU=y
- CONFIG_LEDS_TRIGGER_GPIO=y
- CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
--CONFIG_LEDS_TRIGGER_TRANSIENT=y
--CONFIG_LEDS_TRIGGER_CAMERA=y
-+CONFIG_LEDS_TRIGGER_TRANSIENT=m
-+CONFIG_LEDS_TRIGGER_CAMERA=m
-+CONFIG_LEDS_TRIGGER_INPUT=y
-+CONFIG_RTC_CLASS=y
-+# CONFIG_RTC_HCTOSYS is not set
-+CONFIG_RTC_DRV_DS1307=m
-+CONFIG_RTC_DRV_DS1374=m
-+CONFIG_RTC_DRV_DS1672=m
-+CONFIG_RTC_DRV_DS3232=m
-+CONFIG_RTC_DRV_MAX6900=m
-+CONFIG_RTC_DRV_RS5C372=m
-+CONFIG_RTC_DRV_ISL1208=m
-+CONFIG_RTC_DRV_ISL12022=m
-+CONFIG_RTC_DRV_ISL12057=m
-+CONFIG_RTC_DRV_X1205=m
-+CONFIG_RTC_DRV_PCF2127=m
-+CONFIG_RTC_DRV_PCF8523=m
-+CONFIG_RTC_DRV_PCF8563=m
-+CONFIG_RTC_DRV_PCF8583=m
-+CONFIG_RTC_DRV_M41T80=m
-+CONFIG_RTC_DRV_BQ32K=m
-+CONFIG_RTC_DRV_S35390A=m
-+CONFIG_RTC_DRV_FM3130=m
-+CONFIG_RTC_DRV_RX8581=m
-+CONFIG_RTC_DRV_RX8025=m
-+CONFIG_RTC_DRV_EM3027=m
-+CONFIG_RTC_DRV_RV3029C2=m
-+CONFIG_RTC_DRV_M41T93=m
-+CONFIG_RTC_DRV_M41T94=m
-+CONFIG_RTC_DRV_DS1305=m
-+CONFIG_RTC_DRV_DS1390=m
-+CONFIG_RTC_DRV_MAX6902=m
-+CONFIG_RTC_DRV_R9701=m
-+CONFIG_RTC_DRV_RS5C348=m
-+CONFIG_RTC_DRV_DS3234=m
-+CONFIG_RTC_DRV_PCF2123=m
-+CONFIG_RTC_DRV_RX4581=m
-+CONFIG_DMADEVICES=y
-+CONFIG_DMA_BCM2835=y
-+CONFIG_DMA_BCM2708=y
-+CONFIG_UIO=m
-+CONFIG_UIO_PDRV_GENIRQ=m
- CONFIG_STAGING=y
--CONFIG_USB_DWC2=y
--CONFIG_USB_DWC2_HOST=y
-+CONFIG_PRISM2_USB=m
-+CONFIG_R8712U=m
-+CONFIG_R8188EU=m
-+CONFIG_R8723AU=m
-+CONFIG_VT6656=m
-+CONFIG_SPEAKUP=m
-+CONFIG_SPEAKUP_SYNTH_SOFT=m
-+CONFIG_STAGING_MEDIA=y
-+CONFIG_LIRC_STAGING=y
-+CONFIG_LIRC_IMON=m
-+CONFIG_LIRC_RPI=m
-+CONFIG_LIRC_SASEM=m
-+CONFIG_LIRC_SERIAL=m
-+CONFIG_FB_TFT=m
-+CONFIG_FB_TFT_AGM1264K_FL=m
-+CONFIG_FB_TFT_BD663474=m
-+CONFIG_FB_TFT_HX8340BN=m
-+CONFIG_FB_TFT_HX8347D=m
-+CONFIG_FB_TFT_HX8353D=m
-+CONFIG_FB_TFT_ILI9320=m
-+CONFIG_FB_TFT_ILI9325=m
-+CONFIG_FB_TFT_ILI9340=m
-+CONFIG_FB_TFT_ILI9341=m
-+CONFIG_FB_TFT_ILI9481=m
-+CONFIG_FB_TFT_ILI9486=m
-+CONFIG_FB_TFT_PCD8544=m
-+CONFIG_FB_TFT_RA8875=m
-+CONFIG_FB_TFT_S6D02A1=m
-+CONFIG_FB_TFT_S6D1121=m
-+CONFIG_FB_TFT_SSD1289=m
-+CONFIG_FB_TFT_SSD1306=m
-+CONFIG_FB_TFT_SSD1331=m
-+CONFIG_FB_TFT_SSD1351=m
-+CONFIG_FB_TFT_ST7735R=m
-+CONFIG_FB_TFT_TINYLCD=m
-+CONFIG_FB_TFT_TLS8204=m
-+CONFIG_FB_TFT_UC1701=m
-+CONFIG_FB_TFT_UPD161704=m
-+CONFIG_FB_TFT_WATTEROTT=m
-+CONFIG_FB_FLEX=m
-+CONFIG_FB_TFT_FBTFT_DEVICE=m
-+CONFIG_MAILBOX=y
-+CONFIG_BCM2835_MBOX=y
- # CONFIG_IOMMU_SUPPORT is not set
-+CONFIG_EXTCON=m
-+CONFIG_EXTCON_ARIZONA=m
-+CONFIG_IIO=m
-+CONFIG_IIO_BUFFER=y
-+CONFIG_IIO_BUFFER_CB=y
-+CONFIG_IIO_KFIFO_BUF=m
-+CONFIG_DHT11=m
-+CONFIG_RASPBERRYPI_FIRMWARE=y
- CONFIG_EXT2_FS=y
- CONFIG_EXT2_FS_XATTR=y
- CONFIG_EXT2_FS_POSIX_ACL=y
-@@ -107,18 +1105,110 @@ CONFIG_EXT3_FS=y
- CONFIG_EXT3_FS_POSIX_ACL=y
- CONFIG_EXT4_FS=y
- CONFIG_EXT4_FS_POSIX_ACL=y
-+CONFIG_EXT4_FS_SECURITY=y
-+CONFIG_REISERFS_FS=m
-+CONFIG_REISERFS_FS_XATTR=y
-+CONFIG_REISERFS_FS_POSIX_ACL=y
-+CONFIG_REISERFS_FS_SECURITY=y
-+CONFIG_JFS_FS=m
-+CONFIG_JFS_POSIX_ACL=y
-+CONFIG_JFS_SECURITY=y
-+CONFIG_JFS_STATISTICS=y
-+CONFIG_XFS_FS=m
-+CONFIG_XFS_QUOTA=y
-+CONFIG_XFS_POSIX_ACL=y
-+CONFIG_XFS_RT=y
-+CONFIG_GFS2_FS=m
-+CONFIG_OCFS2_FS=m
-+CONFIG_BTRFS_FS=m
-+CONFIG_BTRFS_FS_POSIX_ACL=y
-+CONFIG_NILFS2_FS=m
-+CONFIG_F2FS_FS=y
- CONFIG_FANOTIFY=y
-+CONFIG_QFMT_V1=m
-+CONFIG_QFMT_V2=m
-+CONFIG_AUTOFS4_FS=y
-+CONFIG_FUSE_FS=m
-+CONFIG_CUSE=m
-+CONFIG_FSCACHE=y
-+CONFIG_FSCACHE_STATS=y
-+CONFIG_FSCACHE_HISTOGRAM=y
-+CONFIG_CACHEFILES=y
-+CONFIG_ISO9660_FS=m
-+CONFIG_JOLIET=y
-+CONFIG_ZISOFS=y
-+CONFIG_UDF_FS=m
- CONFIG_MSDOS_FS=y
- CONFIG_VFAT_FS=y
-+CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
-+CONFIG_NTFS_FS=m
-+CONFIG_NTFS_RW=y
- CONFIG_TMPFS=y
- CONFIG_TMPFS_POSIX_ACL=y
--# CONFIG_MISC_FILESYSTEMS is not set
-+CONFIG_CONFIGFS_FS=y
-+CONFIG_ECRYPT_FS=m
-+CONFIG_HFS_FS=m
-+CONFIG_HFSPLUS_FS=m
-+CONFIG_SQUASHFS=m
-+CONFIG_SQUASHFS_XATTR=y
-+CONFIG_SQUASHFS_LZO=y
-+CONFIG_SQUASHFS_XZ=y
- CONFIG_NFS_FS=y
--CONFIG_NFSD=y
-+CONFIG_NFS_V3_ACL=y
-+CONFIG_NFS_V4=y
-+CONFIG_NFS_SWAP=y
-+CONFIG_ROOT_NFS=y
-+CONFIG_NFS_FSCACHE=y
-+CONFIG_NFSD=m
-+CONFIG_NFSD_V3_ACL=y
-+CONFIG_NFSD_V4=y
-+CONFIG_CIFS=m
-+CONFIG_CIFS_WEAK_PW_HASH=y
-+CONFIG_CIFS_UPCALL=y
-+CONFIG_CIFS_XATTR=y
-+CONFIG_CIFS_POSIX=y
-+CONFIG_9P_FS=m
-+CONFIG_9P_FS_POSIX_ACL=y
-+CONFIG_NLS_DEFAULT="utf8"
- CONFIG_NLS_CODEPAGE_437=y
-+CONFIG_NLS_CODEPAGE_737=m
-+CONFIG_NLS_CODEPAGE_775=m
-+CONFIG_NLS_CODEPAGE_850=m
-+CONFIG_NLS_CODEPAGE_852=m
-+CONFIG_NLS_CODEPAGE_855=m
-+CONFIG_NLS_CODEPAGE_857=m
-+CONFIG_NLS_CODEPAGE_860=m
-+CONFIG_NLS_CODEPAGE_861=m
-+CONFIG_NLS_CODEPAGE_862=m
-+CONFIG_NLS_CODEPAGE_863=m
-+CONFIG_NLS_CODEPAGE_864=m
-+CONFIG_NLS_CODEPAGE_865=m
-+CONFIG_NLS_CODEPAGE_866=m
-+CONFIG_NLS_CODEPAGE_869=m
-+CONFIG_NLS_CODEPAGE_936=m
-+CONFIG_NLS_CODEPAGE_950=m
-+CONFIG_NLS_CODEPAGE_932=m
-+CONFIG_NLS_CODEPAGE_949=m
-+CONFIG_NLS_CODEPAGE_874=m
-+CONFIG_NLS_ISO8859_8=m
-+CONFIG_NLS_CODEPAGE_1250=m
-+CONFIG_NLS_CODEPAGE_1251=m
- CONFIG_NLS_ASCII=y
--CONFIG_NLS_ISO8859_1=y
-+CONFIG_NLS_ISO8859_1=m
-+CONFIG_NLS_ISO8859_2=m
-+CONFIG_NLS_ISO8859_3=m
-+CONFIG_NLS_ISO8859_4=m
-+CONFIG_NLS_ISO8859_5=m
-+CONFIG_NLS_ISO8859_6=m
-+CONFIG_NLS_ISO8859_7=m
-+CONFIG_NLS_ISO8859_9=m
-+CONFIG_NLS_ISO8859_13=m
-+CONFIG_NLS_ISO8859_14=m
-+CONFIG_NLS_ISO8859_15=m
-+CONFIG_NLS_KOI8_R=m
-+CONFIG_NLS_KOI8_U=m
- CONFIG_NLS_UTF8=y
-+CONFIG_DLM=m
- CONFIG_PRINTK_TIME=y
- CONFIG_BOOT_PRINTK_DELAY=y
- CONFIG_DYNAMIC_DEBUG=y
-@@ -128,14 +1218,38 @@ CONFIG_DEBUG_INFO=y
- CONFIG_UNUSED_SYMBOLS=y
- CONFIG_DEBUG_MEMORY_INIT=y
- CONFIG_LOCKUP_DETECTOR=y
-+CONFIG_TIMER_STATS=y
-+# CONFIG_DEBUG_PREEMPT is not set
-+CONFIG_LATENCYTOP=y
-+CONFIG_IRQSOFF_TRACER=y
- CONFIG_SCHED_TRACER=y
- CONFIG_STACK_TRACER=y
-+CONFIG_BLK_DEV_IO_TRACE=y
-+# CONFIG_KPROBE_EVENT is not set
- CONFIG_FUNCTION_PROFILER=y
- CONFIG_TEST_KSTRTOX=y
- CONFIG_KGDB=y
- CONFIG_KGDB_KDB=y
-+CONFIG_KDB_KEYBOARD=y
- CONFIG_STRICT_DEVMEM=y
- CONFIG_DEBUG_LL=y
- CONFIG_EARLY_PRINTK=y
-+CONFIG_CRYPTO_USER=m
-+CONFIG_CRYPTO_CRYPTD=m
-+CONFIG_CRYPTO_CBC=y
-+CONFIG_CRYPTO_CTS=m
-+CONFIG_CRYPTO_XTS=m
-+CONFIG_CRYPTO_XCBC=m
-+CONFIG_CRYPTO_SHA512=m
-+CONFIG_CRYPTO_TGR192=m
-+CONFIG_CRYPTO_WP512=m
-+CONFIG_CRYPTO_CAST5=m
-+CONFIG_CRYPTO_DES=y
-+# CONFIG_CRYPTO_HW is not set
-+CONFIG_ARM_CRYPTO=y
-+CONFIG_CRYPTO_SHA1_ARM=m
-+CONFIG_CRYPTO_AES_ARM=m
-+CONFIG_CRC_ITU_T=y
-+CONFIG_LIBCRC32C=y
- # CONFIG_XZ_DEC_ARM is not set
- # CONFIG_XZ_DEC_ARMTHUMB is not set
diff --git a/target/linux/brcm2708/patches-4.4/0078-rpi-ft5406-Add-touchscreen-driver-for-pi-LCD-display.patch b/target/linux/brcm2708/patches-4.4/0078-rpi-ft5406-Add-touchscreen-driver-for-pi-LCD-display.patch
deleted file mode 100644
index edd9960..0000000
--- a/target/linux/brcm2708/patches-4.4/0078-rpi-ft5406-Add-touchscreen-driver-for-pi-LCD-display.patch
+++ /dev/null
@@ -1,290 +0,0 @@
-From 3394e57d5ca8efcb58dd23303c57b9fb734dc632 Mon Sep 17 00:00:00 2001
-From: Gordon Hollingworth <gordon at raspberrypi.org>
-Date: Tue, 12 May 2015 14:47:56 +0100
-Subject: [PATCH] rpi-ft5406: Add touchscreen driver for pi LCD display
-
-Fix driver detection failure Check that the buffer response is non-zero meaning the touchscreen was detected
-
-rpi-ft5406: Use firmware API
----
- drivers/input/touchscreen/Kconfig | 7 +
- drivers/input/touchscreen/Makefile | 1 +
- drivers/input/touchscreen/rpi-ft5406.c | 246 +++++++++++++++++++++++++++++++++
- 3 files changed, 254 insertions(+)
- create mode 100644 drivers/input/touchscreen/rpi-ft5406.c
-
---- a/drivers/input/touchscreen/Kconfig
-+++ b/drivers/input/touchscreen/Kconfig
-@@ -608,6 +608,13 @@ config TOUCHSCREEN_EDT_FT5X06
- To compile this driver as a module, choose M here: the
- module will be called edt-ft5x06.
-
-+config TOUCHSCREEN_RPI_FT5406
-+ tristate "Raspberry Pi FT5406 driver"
-+ depends on RASPBERRYPI_FIRMWARE
-+ help
-+ Say Y here to enable the Raspberry Pi memory based FT5406 device
-+
-+
- config TOUCHSCREEN_MIGOR
- tristate "Renesas MIGO-R touchscreen"
- depends on SH_MIGOR && I2C
---- a/drivers/input/touchscreen/Makefile
-+++ b/drivers/input/touchscreen/Makefile
-@@ -29,6 +29,7 @@ obj-$(CONFIG_TOUCHSCREEN_DA9034) += da90
- obj-$(CONFIG_TOUCHSCREEN_DA9052) += da9052_tsi.o
- obj-$(CONFIG_TOUCHSCREEN_DYNAPRO) += dynapro.o
- obj-$(CONFIG_TOUCHSCREEN_EDT_FT5X06) += edt-ft5x06.o
-+obj-$(CONFIG_TOUCHSCREEN_RPI_FT5406) += rpi-ft5406.o
- obj-$(CONFIG_TOUCHSCREEN_HAMPSHIRE) += hampshire.o
- obj-$(CONFIG_TOUCHSCREEN_GUNZE) += gunze.o
- obj-$(CONFIG_TOUCHSCREEN_EETI) += eeti_ts.o
---- /dev/null
-+++ b/drivers/input/touchscreen/rpi-ft5406.c
-@@ -0,0 +1,246 @@
-+/*
-+ * Driver for memory based ft5406 touchscreen
-+ *
-+ * Copyright (C) 2015 Raspberry Pi
-+ *
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ */
-+
-+
-+#include <linux/module.h>
-+#include <linux/interrupt.h>
-+#include <linux/input.h>
-+#include <linux/irq.h>
-+#include <linux/delay.h>
-+#include <linux/slab.h>
-+#include <linux/bitops.h>
-+#include <linux/input/mt.h>
-+#include <linux/kthread.h>
-+#include <linux/platform_device.h>
-+#include <asm/io.h>
-+#include <soc/bcm2835/raspberrypi-firmware.h>
-+
-+#define MAXIMUM_SUPPORTED_POINTS 10
-+struct ft5406_regs {
-+ uint8_t device_mode;
-+ uint8_t gesture_id;
-+ uint8_t num_points;
-+ struct ft5406_touch {
-+ uint8_t xh;
-+ uint8_t xl;
-+ uint8_t yh;
-+ uint8_t yl;
-+ uint8_t res1;
-+ uint8_t res2;
-+ } point[MAXIMUM_SUPPORTED_POINTS];
-+};
-+
-+#define SCREEN_WIDTH 800
-+#define SCREEN_HEIGHT 480
-+
-+struct ft5406 {
-+ struct platform_device * pdev;
-+ struct input_dev * input_dev;
-+ void __iomem * ts_base;
-+ struct ft5406_regs * regs;
-+ struct task_struct * thread;
-+};
-+
-+/* Thread to poll for touchscreen events
-+ *
-+ * This thread polls the memory based register copy of the ft5406 registers
-+ * using the number of points register to know whether the copy has been
-+ * updated (we write 99 to the memory copy, the GPU will write between
-+ * 0 - 10 points)
-+ */
-+static int ft5406_thread(void *arg)
-+{
-+ struct ft5406 *ts = (struct ft5406 *) arg;
-+ struct ft5406_regs regs;
-+ int known_ids = 0;
-+
-+ while(!kthread_should_stop())
-+ {
-+ // 60fps polling
-+ msleep_interruptible(17);
-+ memcpy_fromio(®s, ts->regs, sizeof(*ts->regs));
-+ writel(99, &ts->regs->num_points);
-+ // Do not output if theres no new information (num_points is 99)
-+ // or we have no touch points and don't need to release any
-+ if(!(regs.num_points == 99 || (regs.num_points == 0 && known_ids == 0)))
-+ {
-+ int i;
-+ int modified_ids = 0, released_ids;
-+ for(i = 0; i < regs.num_points; i++)
-+ {
-+ int x = (((int) regs.point[i].xh & 0xf) << 8) + regs.point[i].xl;
-+ int y = (((int) regs.point[i].yh & 0xf) << 8) + regs.point[i].yl;
-+ int touchid = (regs.point[i].yh >> 4) & 0xf;
-+
-+ modified_ids |= 1 << touchid;
-+
-+ if(!((1 << touchid) & known_ids))
-+ dev_dbg(&ts->pdev->dev, "x = %d, y = %d, touchid = %d\n", x, y, touchid);
-+
-+ input_mt_slot(ts->input_dev, touchid);
-+ input_mt_report_slot_state(ts->input_dev, MT_TOOL_FINGER, 1);
-+
-+ input_report_abs(ts->input_dev, ABS_MT_POSITION_X, x);
-+ input_report_abs(ts->input_dev, ABS_MT_POSITION_Y, y);
-+
-+ }
-+
-+ released_ids = known_ids & ~modified_ids;
-+ for(i = 0; released_ids && i < MAXIMUM_SUPPORTED_POINTS; i++)
-+ {
-+ if(released_ids & (1<<i))
-+ {
-+ dev_dbg(&ts->pdev->dev, "Released %d, known = %x modified = %x\n", i, known_ids, modified_ids);
-+ input_mt_slot(ts->input_dev, i);
-+ input_mt_report_slot_state(ts->input_dev, MT_TOOL_FINGER, 0);
-+ modified_ids &= ~(1 << i);
-+ }
-+ }
-+ known_ids = modified_ids;
-+
-+ input_mt_report_pointer_emulation(ts->input_dev, true);
-+ input_sync(ts->input_dev);
-+ }
-+
-+ }
-+
-+ return 0;
-+}
-+
-+static int ft5406_probe(struct platform_device *pdev)
-+{
-+ int ret;
-+ struct input_dev * input_dev = input_allocate_device();
-+ struct ft5406 * ts;
-+ struct device_node *fw_node;
-+ struct rpi_firmware *fw;
-+ u32 touchbuf;
-+
-+ dev_info(&pdev->dev, "Probing device\n");
-+
-+ fw_node = of_parse_phandle(pdev->dev.of_node, "firmware", 0);
-+ if (!fw_node) {
-+ dev_err(&pdev->dev, "Missing firmware node\n");
-+ return -ENOENT;
-+ }
-+
-+ fw = rpi_firmware_get(fw_node);
-+ if (!fw)
-+ return -EPROBE_DEFER;
-+
-+ ret = rpi_firmware_property(fw, RPI_FIRMWARE_FRAMEBUFFER_GET_TOUCHBUF,
-+ &touchbuf, sizeof(touchbuf));
-+ if (ret) {
-+ dev_err(&pdev->dev, "Failed to get touch buffer\n");
-+ return ret;
-+ }
-+
-+ if (!touchbuf) {
-+ dev_err(&pdev->dev, "Touchscreen not detected\n");
-+ return -ENODEV;
-+ }
-+
-+ dev_dbg(&pdev->dev, "Got TS buffer 0x%x\n", touchbuf);
-+
-+ ts = kzalloc(sizeof(struct ft5406), GFP_KERNEL);
-+
-+ if (!ts || !input_dev) {
-+ ret = -ENOMEM;
-+ dev_err(&pdev->dev, "Failed to allocate memory\n");
-+ return ret;
-+ }
-+ ts->input_dev = input_dev;
-+ platform_set_drvdata(pdev, ts);
-+ ts->pdev = pdev;
-+
-+ input_dev->name = "FT5406 memory based driver";
-+
-+ __set_bit(EV_KEY, input_dev->evbit);
-+ __set_bit(EV_SYN, input_dev->evbit);
-+ __set_bit(EV_ABS, input_dev->evbit);
-+
-+ input_set_abs_params(input_dev, ABS_MT_POSITION_X, 0,
-+ SCREEN_WIDTH, 0, 0);
-+ input_set_abs_params(input_dev, ABS_MT_POSITION_Y, 0,
-+ SCREEN_HEIGHT, 0, 0);
-+
-+ input_mt_init_slots(input_dev, MAXIMUM_SUPPORTED_POINTS, INPUT_MT_DIRECT);
-+
-+ input_set_drvdata(input_dev, ts);
-+
-+ ret = input_register_device(input_dev);
-+ if (ret) {
-+ dev_err(&pdev->dev, "could not register input device, %d\n",
-+ ret);
-+ return ret;
-+ }
-+
-+ // mmap the physical memory
-+ touchbuf &= ~0xc0000000;
-+ ts->ts_base = ioremap(touchbuf, sizeof(*ts->regs));
-+ if(ts->ts_base == NULL)
-+ {
-+ dev_err(&pdev->dev, "Failed to map physical address\n");
-+ input_unregister_device(input_dev);
-+ kzfree(ts);
-+ return -ENOMEM;
-+ }
-+
-+ ts->regs = (struct ft5406_regs *) ts->ts_base;
-+
-+ // create thread to poll the touch events
-+ ts->thread = kthread_run(ft5406_thread, ts, "ft5406");
-+ if(ts->thread == NULL)
-+ {
-+ dev_err(&pdev->dev, "Failed to create kernel thread");
-+ iounmap(ts->ts_base);
-+ input_unregister_device(input_dev);
-+ kzfree(ts);
-+ }
-+
-+ return 0;
-+}
-+
-+static int ft5406_remove(struct platform_device *pdev)
-+{
-+ struct ft5406 *ts = (struct ft5406 *) platform_get_drvdata(pdev);
-+
-+ dev_info(&pdev->dev, "Removing rpi-ft5406\n");
-+
-+ kthread_stop(ts->thread);
-+ iounmap(ts->ts_base);
-+ input_unregister_device(ts->input_dev);
-+ kzfree(ts);
-+
-+ return 0;
-+}
-+
-+static const struct of_device_id ft5406_match[] = {
-+ { .compatible = "rpi,rpi-ft5406", },
-+ {},
-+};
-+MODULE_DEVICE_TABLE(of, ft5406_match);
-+
-+static struct platform_driver ft5406_driver = {
-+ .driver = {
-+ .name = "rpi-ft5406",
-+ .owner = THIS_MODULE,
-+ .of_match_table = ft5406_match,
-+ },
-+ .probe = ft5406_probe,
-+ .remove = ft5406_remove,
-+};
-+
-+module_platform_driver(ft5406_driver);
-+
-+MODULE_AUTHOR("Gordon Hollingworth");
-+MODULE_DESCRIPTION("Touchscreen driver for memory based FT5406");
-+MODULE_LICENSE("GPL");
diff --git a/target/linux/brcm2708/patches-4.4/0079-Improve-__copy_to_user-and-__copy_from_user-performa.patch b/target/linux/brcm2708/patches-4.4/0079-Improve-__copy_to_user-and-__copy_from_user-performa.patch
deleted file mode 100644
index 6d1349b..0000000
--- a/target/linux/brcm2708/patches-4.4/0079-Improve-__copy_to_user-and-__copy_from_user-performa.patch
+++ /dev/null
@@ -1,1509 +0,0 @@
-From 6fe6b3546c95737d0d7aa91cc1f0a45d099e7c0c Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 13 Oct 2014 11:47:53 +0100
-Subject: [PATCH] Improve __copy_to_user and __copy_from_user performance
-
-Provide a __copy_from_user that uses memcpy. On BCM2708, use
-optimised memcpy/memmove/memcmp/memset implementations.
-
-arch/arm: Add mmiocpy/set aliases for memcpy/set
-
-See: https://github.com/raspberrypi/linux/issues/1082
----
- arch/arm/include/asm/string.h | 5 +
- arch/arm/include/asm/uaccess.h | 3 +
- arch/arm/lib/Makefile | 15 +-
- arch/arm/lib/arm-mem.h | 159 ++++++++++++
- arch/arm/lib/copy_from_user.S | 4 +-
- arch/arm/lib/exports_rpi.c | 37 +++
- arch/arm/lib/memcmp_rpi.S | 285 +++++++++++++++++++++
- arch/arm/lib/memcpy_rpi.S | 61 +++++
- arch/arm/lib/memcpymove.h | 506 +++++++++++++++++++++++++++++++++++++
- arch/arm/lib/memmove_rpi.S | 61 +++++
- arch/arm/lib/memset_rpi.S | 123 +++++++++
- arch/arm/lib/uaccess_with_memcpy.c | 112 +++++++-
- 12 files changed, 1365 insertions(+), 6 deletions(-)
- create mode 100644 arch/arm/lib/arm-mem.h
- create mode 100644 arch/arm/lib/exports_rpi.c
- create mode 100644 arch/arm/lib/memcmp_rpi.S
- create mode 100644 arch/arm/lib/memcpy_rpi.S
- create mode 100644 arch/arm/lib/memcpymove.h
- create mode 100644 arch/arm/lib/memmove_rpi.S
- create mode 100644 arch/arm/lib/memset_rpi.S
-
---- a/arch/arm/include/asm/string.h
-+++ b/arch/arm/include/asm/string.h
-@@ -24,6 +24,11 @@ extern void * memchr(const void *, int,
- #define __HAVE_ARCH_MEMSET
- extern void * memset(void *, int, __kernel_size_t);
-
-+#ifdef CONFIG_MACH_BCM2708
-+#define __HAVE_ARCH_MEMCMP
-+extern int memcmp(const void *, const void *, size_t);
-+#endif
-+
- extern void __memzero(void *ptr, __kernel_size_t n);
-
- #define memset(p,v,n) \
---- a/arch/arm/include/asm/uaccess.h
-+++ b/arch/arm/include/asm/uaccess.h
-@@ -493,6 +493,9 @@ do { \
- extern unsigned long __must_check
- arm_copy_from_user(void *to, const void __user *from, unsigned long n);
-
-+extern unsigned long __must_check
-+__copy_from_user_std(void *to, const void __user *from, unsigned long n);
-+
- static inline unsigned long __must_check
- __copy_from_user(void *to, const void __user *from, unsigned long n)
- {
---- a/arch/arm/lib/Makefile
-+++ b/arch/arm/lib/Makefile
-@@ -6,9 +6,8 @@
-
- lib-y := backtrace.o changebit.o csumipv6.o csumpartial.o \
- csumpartialcopy.o csumpartialcopyuser.o clearbit.o \
-- delay.o delay-loop.o findbit.o memchr.o memcpy.o \
-- memmove.o memset.o memzero.o setbit.o \
-- strchr.o strrchr.o \
-+ delay.o delay-loop.o findbit.o memchr.o memzero.o \
-+ setbit.o strchr.o strrchr.o \
- testchangebit.o testclearbit.o testsetbit.o \
- ashldi3.o ashrdi3.o lshrdi3.o muldi3.o \
- ucmpdi2.o lib1funcs.o div64.o \
-@@ -18,6 +17,16 @@ lib-y := backtrace.o changebit.o csumip
- mmu-y := clear_user.o copy_page.o getuser.o putuser.o \
- copy_from_user.o copy_to_user.o
-
-+# Choose optimised implementations for Raspberry Pi
-+ifeq ($(CONFIG_MACH_BCM2708),y)
-+ CFLAGS_uaccess_with_memcpy.o += -DCOPY_FROM_USER_THRESHOLD=1600
-+ CFLAGS_uaccess_with_memcpy.o += -DCOPY_TO_USER_THRESHOLD=672
-+ obj-$(CONFIG_MODULES) += exports_rpi.o
-+ lib-y += memcpy_rpi.o memmove_rpi.o memset_rpi.o memcmp_rpi.o
-+else
-+ lib-y += memcpy.o memmove.o memset.o
-+endif
-+
- # using lib_ here won't override already available weak symbols
- obj-$(CONFIG_UACCESS_WITH_MEMCPY) += uaccess_with_memcpy.o
-
---- /dev/null
-+++ b/arch/arm/lib/arm-mem.h
-@@ -0,0 +1,159 @@
-+/*
-+Copyright (c) 2013, Raspberry Pi Foundation
-+Copyright (c) 2013, RISC OS Open Ltd
-+All rights reserved.
-+
-+Redistribution and use in source and binary forms, with or without
-+modification, are permitted provided that the following conditions are met:
-+ * Redistributions of source code must retain the above copyright
-+ notice, this list of conditions and the following disclaimer.
-+ * Redistributions in binary form must reproduce the above copyright
-+ notice, this list of conditions and the following disclaimer in the
-+ documentation and/or other materials provided with the distribution.
-+ * Neither the name of the copyright holder nor the
-+ names of its contributors may be used to endorse or promote products
-+ derived from this software without specific prior written permission.
-+
-+THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND
-+ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
-+WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
-+DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY
-+DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
-+LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
-+ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
-+(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+*/
-+
-+.macro myfunc fname
-+ .func fname
-+ .global fname
-+fname:
-+.endm
-+
-+.macro preload_leading_step1 backwards, ptr, base
-+/* If the destination is already 16-byte aligned, then we need to preload
-+ * between 0 and prefetch_distance (inclusive) cache lines ahead so there
-+ * are no gaps when the inner loop starts.
-+ */
-+ .if backwards
-+ sub ptr, base, #1
-+ bic ptr, ptr, #31
-+ .else
-+ bic ptr, base, #31
-+ .endif
-+ .set OFFSET, 0
-+ .rept prefetch_distance+1
-+ pld [ptr, #OFFSET]
-+ .if backwards
-+ .set OFFSET, OFFSET-32
-+ .else
-+ .set OFFSET, OFFSET+32
-+ .endif
-+ .endr
-+.endm
-+
-+.macro preload_leading_step2 backwards, ptr, base, leading_bytes, tmp
-+/* However, if the destination is not 16-byte aligned, we may need to
-+ * preload one more cache line than that. The question we need to ask is:
-+ * are the leading bytes more than the amount by which the source
-+ * pointer will be rounded down for preloading, and if so, by how many
-+ * cache lines?
-+ */
-+ .if backwards
-+/* Here we compare against how many bytes we are into the
-+ * cache line, counting down from the highest such address.
-+ * Effectively, we want to calculate
-+ * leading_bytes = dst&15
-+ * cacheline_offset = 31-((src-leading_bytes-1)&31)
-+ * extra_needed = leading_bytes - cacheline_offset
-+ * and test if extra_needed is <= 0, or rearranging:
-+ * leading_bytes + (src-leading_bytes-1)&31 <= 31
-+ */
-+ mov tmp, base, lsl #32-5
-+ sbc tmp, tmp, leading_bytes, lsl #32-5
-+ adds tmp, tmp, leading_bytes, lsl #32-5
-+ bcc 61f
-+ pld [ptr, #-32*(prefetch_distance+1)]
-+ .else
-+/* Effectively, we want to calculate
-+ * leading_bytes = (-dst)&15
-+ * cacheline_offset = (src+leading_bytes)&31
-+ * extra_needed = leading_bytes - cacheline_offset
-+ * and test if extra_needed is <= 0.
-+ */
-+ mov tmp, base, lsl #32-5
-+ add tmp, tmp, leading_bytes, lsl #32-5
-+ rsbs tmp, tmp, leading_bytes, lsl #32-5
-+ bls 61f
-+ pld [ptr, #32*(prefetch_distance+1)]
-+ .endif
-+61:
-+.endm
-+
-+.macro preload_trailing backwards, base, remain, tmp
-+ /* We need either 0, 1 or 2 extra preloads */
-+ .if backwards
-+ rsb tmp, base, #0
-+ mov tmp, tmp, lsl #32-5
-+ .else
-+ mov tmp, base, lsl #32-5
-+ .endif
-+ adds tmp, tmp, remain, lsl #32-5
-+ adceqs tmp, tmp, #0
-+ /* The instruction above has two effects: ensures Z is only
-+ * set if C was clear (so Z indicates that both shifted quantities
-+ * were 0), and clears C if Z was set (so C indicates that the sum
-+ * of the shifted quantities was greater and not equal to 32) */
-+ beq 82f
-+ .if backwards
-+ sub tmp, base, #1
-+ bic tmp, tmp, #31
-+ .else
-+ bic tmp, base, #31
-+ .endif
-+ bcc 81f
-+ .if backwards
-+ pld [tmp, #-32*(prefetch_distance+1)]
-+81:
-+ pld [tmp, #-32*prefetch_distance]
-+ .else
-+ pld [tmp, #32*(prefetch_distance+2)]
-+81:
-+ pld [tmp, #32*(prefetch_distance+1)]
-+ .endif
-+82:
-+.endm
-+
-+.macro preload_all backwards, narrow_case, shift, base, remain, tmp0, tmp1
-+ .if backwards
-+ sub tmp0, base, #1
-+ bic tmp0, tmp0, #31
-+ pld [tmp0]
-+ sub tmp1, base, remain, lsl #shift
-+ .else
-+ bic tmp0, base, #31
-+ pld [tmp0]
-+ add tmp1, base, remain, lsl #shift
-+ sub tmp1, tmp1, #1
-+ .endif
-+ bic tmp1, tmp1, #31
-+ cmp tmp1, tmp0
-+ beq 92f
-+ .if narrow_case
-+ /* In this case, all the data fits in either 1 or 2 cache lines */
-+ pld [tmp1]
-+ .else
-+91:
-+ .if backwards
-+ sub tmp0, tmp0, #32
-+ .else
-+ add tmp0, tmp0, #32
-+ .endif
-+ cmp tmp0, tmp1
-+ pld [tmp0]
-+ bne 91b
-+ .endif
-+92:
-+.endm
---- a/arch/arm/lib/copy_from_user.S
-+++ b/arch/arm/lib/copy_from_user.S
-@@ -89,11 +89,13 @@
-
- .text
-
--ENTRY(arm_copy_from_user)
-+ENTRY(__copy_from_user_std)
-+WEAK(arm_copy_from_user)
-
- #include "copy_template.S"
-
- ENDPROC(arm_copy_from_user)
-+ENDPROC(__copy_from_user_std)
-
- .pushsection .fixup,"ax"
- .align 0
---- /dev/null
-+++ b/arch/arm/lib/exports_rpi.c
-@@ -0,0 +1,37 @@
-+/**
-+ * Copyright (c) 2014, Raspberry Pi (Trading) Ltd.
-+ *
-+ * Redistribution and use in source and binary forms, with or without
-+ * modification, are permitted provided that the following conditions
-+ * are met:
-+ * 1. Redistributions of source code must retain the above copyright
-+ * notice, this list of conditions, and the following disclaimer,
-+ * without modification.
-+ * 2. Redistributions in binary form must reproduce the above copyright
-+ * notice, this list of conditions and the following disclaimer in the
-+ * documentation and/or other materials provided with the distribution.
-+ * 3. The names of the above-listed copyright holders may not be used
-+ * to endorse or promote products derived from this software without
-+ * specific prior written permission.
-+ *
-+ * ALTERNATIVELY, this software may be distributed under the terms of the
-+ * GNU General Public License ("GPL") version 2, as published by the Free
-+ * Software Foundation.
-+ *
-+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
-+ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
-+ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
-+ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
-+ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-+ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-+ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+
-+EXPORT_SYMBOL(memcmp);
---- /dev/null
-+++ b/arch/arm/lib/memcmp_rpi.S
-@@ -0,0 +1,285 @@
-+/*
-+Copyright (c) 2013, Raspberry Pi Foundation
-+Copyright (c) 2013, RISC OS Open Ltd
-+All rights reserved.
-+
-+Redistribution and use in source and binary forms, with or without
-+modification, are permitted provided that the following conditions are met:
-+ * Redistributions of source code must retain the above copyright
-+ notice, this list of conditions and the following disclaimer.
-+ * Redistributions in binary form must reproduce the above copyright
-+ notice, this list of conditions and the following disclaimer in the
-+ documentation and/or other materials provided with the distribution.
-+ * Neither the name of the copyright holder nor the
-+ names of its contributors may be used to endorse or promote products
-+ derived from this software without specific prior written permission.
-+
-+THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND
-+ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
-+WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
-+DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY
-+DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
-+LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
-+ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
-+(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+*/
-+
-+#include <linux/linkage.h>
-+#include "arm-mem.h"
-+
-+/* Prevent the stack from becoming executable */
-+#if defined(__linux__) && defined(__ELF__)
-+.section .note.GNU-stack,"",%progbits
-+#endif
-+
-+ .text
-+ .arch armv6
-+ .object_arch armv4
-+ .arm
-+ .altmacro
-+ .p2align 2
-+
-+.macro memcmp_process_head unaligned
-+ .if unaligned
-+ ldr DAT0, [S_1], #4
-+ ldr DAT1, [S_1], #4
-+ ldr DAT2, [S_1], #4
-+ ldr DAT3, [S_1], #4
-+ .else
-+ ldmia S_1!, {DAT0, DAT1, DAT2, DAT3}
-+ .endif
-+ ldmia S_2!, {DAT4, DAT5, DAT6, DAT7}
-+.endm
-+
-+.macro memcmp_process_tail
-+ cmp DAT0, DAT4
-+ cmpeq DAT1, DAT5
-+ cmpeq DAT2, DAT6
-+ cmpeq DAT3, DAT7
-+ bne 200f
-+.endm
-+
-+.macro memcmp_leading_31bytes
-+ movs DAT0, OFF, lsl #31
-+ ldrmib DAT0, [S_1], #1
-+ ldrcsh DAT1, [S_1], #2
-+ ldrmib DAT4, [S_2], #1
-+ ldrcsh DAT5, [S_2], #2
-+ movpl DAT0, #0
-+ movcc DAT1, #0
-+ movpl DAT4, #0
-+ movcc DAT5, #0
-+ submi N, N, #1
-+ subcs N, N, #2
-+ cmp DAT0, DAT4
-+ cmpeq DAT1, DAT5
-+ bne 200f
-+ movs DAT0, OFF, lsl #29
-+ ldrmi DAT0, [S_1], #4
-+ ldrcs DAT1, [S_1], #4
-+ ldrcs DAT2, [S_1], #4
-+ ldrmi DAT4, [S_2], #4
-+ ldmcsia S_2!, {DAT5, DAT6}
-+ movpl DAT0, #0
-+ movcc DAT1, #0
-+ movcc DAT2, #0
-+ movpl DAT4, #0
-+ movcc DAT5, #0
-+ movcc DAT6, #0
-+ submi N, N, #4
-+ subcs N, N, #8
-+ cmp DAT0, DAT4
-+ cmpeq DAT1, DAT5
-+ cmpeq DAT2, DAT6
-+ bne 200f
-+ tst OFF, #16
-+ beq 105f
-+ memcmp_process_head 1
-+ sub N, N, #16
-+ memcmp_process_tail
-+105:
-+.endm
-+
-+.macro memcmp_trailing_15bytes unaligned
-+ movs N, N, lsl #29
-+ .if unaligned
-+ ldrcs DAT0, [S_1], #4
-+ ldrcs DAT1, [S_1], #4
-+ .else
-+ ldmcsia S_1!, {DAT0, DAT1}
-+ .endif
-+ ldrmi DAT2, [S_1], #4
-+ ldmcsia S_2!, {DAT4, DAT5}
-+ ldrmi DAT6, [S_2], #4
-+ movcc DAT0, #0
-+ movcc DAT1, #0
-+ movpl DAT2, #0
-+ movcc DAT4, #0
-+ movcc DAT5, #0
-+ movpl DAT6, #0
-+ cmp DAT0, DAT4
-+ cmpeq DAT1, DAT5
-+ cmpeq DAT2, DAT6
-+ bne 200f
-+ movs N, N, lsl #2
-+ ldrcsh DAT0, [S_1], #2
-+ ldrmib DAT1, [S_1]
-+ ldrcsh DAT4, [S_2], #2
-+ ldrmib DAT5, [S_2]
-+ movcc DAT0, #0
-+ movpl DAT1, #0
-+ movcc DAT4, #0
-+ movpl DAT5, #0
-+ cmp DAT0, DAT4
-+ cmpeq DAT1, DAT5
-+ bne 200f
-+.endm
-+
-+.macro memcmp_long_inner_loop unaligned
-+110:
-+ memcmp_process_head unaligned
-+ pld [S_2, #prefetch_distance*32 + 16]
-+ memcmp_process_tail
-+ memcmp_process_head unaligned
-+ pld [S_1, OFF]
-+ memcmp_process_tail
-+ subs N, N, #32
-+ bhs 110b
-+ /* Just before the final (prefetch_distance+1) 32-byte blocks,
-+ * deal with final preloads */
-+ preload_trailing 0, S_1, N, DAT0
-+ preload_trailing 0, S_2, N, DAT0
-+ add N, N, #(prefetch_distance+2)*32 - 16
-+120:
-+ memcmp_process_head unaligned
-+ memcmp_process_tail
-+ subs N, N, #16
-+ bhs 120b
-+ /* Trailing words and bytes */
-+ tst N, #15
-+ beq 199f
-+ memcmp_trailing_15bytes unaligned
-+199: /* Reached end without detecting a difference */
-+ mov a1, #0
-+ setend le
-+ pop {DAT1-DAT6, pc}
-+.endm
-+
-+.macro memcmp_short_inner_loop unaligned
-+ subs N, N, #16 /* simplifies inner loop termination */
-+ blo 122f
-+120:
-+ memcmp_process_head unaligned
-+ memcmp_process_tail
-+ subs N, N, #16
-+ bhs 120b
-+122: /* Trailing words and bytes */
-+ tst N, #15
-+ beq 199f
-+ memcmp_trailing_15bytes unaligned
-+199: /* Reached end without detecting a difference */
-+ mov a1, #0
-+ setend le
-+ pop {DAT1-DAT6, pc}
-+.endm
-+
-+/*
-+ * int memcmp(const void *s1, const void *s2, size_t n);
-+ * On entry:
-+ * a1 = pointer to buffer 1
-+ * a2 = pointer to buffer 2
-+ * a3 = number of bytes to compare (as unsigned chars)
-+ * On exit:
-+ * a1 = >0/=0/<0 if s1 >/=/< s2
-+ */
-+
-+.set prefetch_distance, 2
-+
-+ENTRY(memcmp)
-+ S_1 .req a1
-+ S_2 .req a2
-+ N .req a3
-+ DAT0 .req a4
-+ DAT1 .req v1
-+ DAT2 .req v2
-+ DAT3 .req v3
-+ DAT4 .req v4
-+ DAT5 .req v5
-+ DAT6 .req v6
-+ DAT7 .req ip
-+ OFF .req lr
-+
-+ push {DAT1-DAT6, lr}
-+ setend be /* lowest-addressed bytes are most significant */
-+
-+ /* To preload ahead as we go, we need at least (prefetch_distance+2) 32-byte blocks */
-+ cmp N, #(prefetch_distance+3)*32 - 1
-+ blo 170f
-+
-+ /* Long case */
-+ /* Adjust N so that the decrement instruction can also test for
-+ * inner loop termination. We want it to stop when there are
-+ * (prefetch_distance+1) complete blocks to go. */
-+ sub N, N, #(prefetch_distance+2)*32
-+ preload_leading_step1 0, DAT0, S_1
-+ preload_leading_step1 0, DAT1, S_2
-+ tst S_2, #31
-+ beq 154f
-+ rsb OFF, S_2, #0 /* no need to AND with 15 here */
-+ preload_leading_step2 0, DAT0, S_1, OFF, DAT2
-+ preload_leading_step2 0, DAT1, S_2, OFF, DAT2
-+ memcmp_leading_31bytes
-+154: /* Second source now cacheline (32-byte) aligned; we have at
-+ * least one prefetch to go. */
-+ /* Prefetch offset is best selected such that it lies in the
-+ * first 8 of each 32 bytes - but it's just as easy to aim for
-+ * the first one */
-+ and OFF, S_1, #31
-+ rsb OFF, OFF, #32*prefetch_distance
-+ tst S_1, #3
-+ bne 140f
-+ memcmp_long_inner_loop 0
-+140: memcmp_long_inner_loop 1
-+
-+170: /* Short case */
-+ teq N, #0
-+ beq 199f
-+ preload_all 0, 0, 0, S_1, N, DAT0, DAT1
-+ preload_all 0, 0, 0, S_2, N, DAT0, DAT1
-+ tst S_2, #3
-+ beq 174f
-+172: subs N, N, #1
-+ blo 199f
-+ ldrb DAT0, [S_1], #1
-+ ldrb DAT4, [S_2], #1
-+ cmp DAT0, DAT4
-+ bne 200f
-+ tst S_2, #3
-+ bne 172b
-+174: /* Second source now 4-byte aligned; we have 0 or more bytes to go */
-+ tst S_1, #3
-+ bne 140f
-+ memcmp_short_inner_loop 0
-+140: memcmp_short_inner_loop 1
-+
-+200: /* Difference found: determine sign. */
-+ movhi a1, #1
-+ movlo a1, #-1
-+ setend le
-+ pop {DAT1-DAT6, pc}
-+
-+ .unreq S_1
-+ .unreq S_2
-+ .unreq N
-+ .unreq DAT0
-+ .unreq DAT1
-+ .unreq DAT2
-+ .unreq DAT3
-+ .unreq DAT4
-+ .unreq DAT5
-+ .unreq DAT6
-+ .unreq DAT7
-+ .unreq OFF
-+ENDPROC(memcmp)
---- /dev/null
-+++ b/arch/arm/lib/memcpy_rpi.S
-@@ -0,0 +1,61 @@
-+/*
-+Copyright (c) 2013, Raspberry Pi Foundation
-+Copyright (c) 2013, RISC OS Open Ltd
-+All rights reserved.
-+
-+Redistribution and use in source and binary forms, with or without
-+modification, are permitted provided that the following conditions are met:
-+ * Redistributions of source code must retain the above copyright
-+ notice, this list of conditions and the following disclaimer.
-+ * Redistributions in binary form must reproduce the above copyright
-+ notice, this list of conditions and the following disclaimer in the
-+ documentation and/or other materials provided with the distribution.
-+ * Neither the name of the copyright holder nor the
-+ names of its contributors may be used to endorse or promote products
-+ derived from this software without specific prior written permission.
-+
-+THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND
-+ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
-+WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
-+DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY
-+DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
-+LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
-+ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
-+(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+*/
-+
-+#include <linux/linkage.h>
-+#include "arm-mem.h"
-+#include "memcpymove.h"
-+
-+/* Prevent the stack from becoming executable */
-+#if defined(__linux__) && defined(__ELF__)
-+.section .note.GNU-stack,"",%progbits
-+#endif
-+
-+ .text
-+ .arch armv6
-+ .object_arch armv4
-+ .arm
-+ .altmacro
-+ .p2align 2
-+
-+/*
-+ * void *memcpy(void * restrict s1, const void * restrict s2, size_t n);
-+ * On entry:
-+ * a1 = pointer to destination
-+ * a2 = pointer to source
-+ * a3 = number of bytes to copy
-+ * On exit:
-+ * a1 preserved
-+ */
-+
-+.set prefetch_distance, 3
-+
-+ENTRY(mmiocpy)
-+ENTRY(memcpy)
-+ memcpy 0
-+ENDPROC(memcpy)
-+ENDPROC(mmiocpy)
---- /dev/null
-+++ b/arch/arm/lib/memcpymove.h
-@@ -0,0 +1,506 @@
-+/*
-+Copyright (c) 2013, Raspberry Pi Foundation
-+Copyright (c) 2013, RISC OS Open Ltd
-+All rights reserved.
-+
-+Redistribution and use in source and binary forms, with or without
-+modification, are permitted provided that the following conditions are met:
-+ * Redistributions of source code must retain the above copyright
-+ notice, this list of conditions and the following disclaimer.
-+ * Redistributions in binary form must reproduce the above copyright
-+ notice, this list of conditions and the following disclaimer in the
-+ documentation and/or other materials provided with the distribution.
-+ * Neither the name of the copyright holder nor the
-+ names of its contributors may be used to endorse or promote products
-+ derived from this software without specific prior written permission.
-+
-+THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND
-+ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
-+WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
-+DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY
-+DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
-+LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
-+ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
-+(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+*/
-+
-+.macro unaligned_words backwards, align, use_pld, words, r0, r1, r2, r3, r4, r5, r6, r7, r8
-+ .if words == 1
-+ .if backwards
-+ mov r1, r0, lsl #32-align*8
-+ ldr r0, [S, #-4]!
-+ orr r1, r1, r0, lsr #align*8
-+ str r1, [D, #-4]!
-+ .else
-+ mov r0, r1, lsr #align*8
-+ ldr r1, [S, #4]!
-+ orr r0, r0, r1, lsl #32-align*8
-+ str r0, [D], #4
-+ .endif
-+ .elseif words == 2
-+ .if backwards
-+ ldr r1, [S, #-4]!
-+ mov r2, r0, lsl #32-align*8
-+ ldr r0, [S, #-4]!
-+ orr r2, r2, r1, lsr #align*8
-+ mov r1, r1, lsl #32-align*8
-+ orr r1, r1, r0, lsr #align*8
-+ stmdb D!, {r1, r2}
-+ .else
-+ ldr r1, [S, #4]!
-+ mov r0, r2, lsr #align*8
-+ ldr r2, [S, #4]!
-+ orr r0, r0, r1, lsl #32-align*8
-+ mov r1, r1, lsr #align*8
-+ orr r1, r1, r2, lsl #32-align*8
-+ stmia D!, {r0, r1}
-+ .endif
-+ .elseif words == 4
-+ .if backwards
-+ ldmdb S!, {r2, r3}
-+ mov r4, r0, lsl #32-align*8
-+ ldmdb S!, {r0, r1}
-+ orr r4, r4, r3, lsr #align*8
-+ mov r3, r3, lsl #32-align*8
-+ orr r3, r3, r2, lsr #align*8
-+ mov r2, r2, lsl #32-align*8
-+ orr r2, r2, r1, lsr #align*8
-+ mov r1, r1, lsl #32-align*8
-+ orr r1, r1, r0, lsr #align*8
-+ stmdb D!, {r1, r2, r3, r4}
-+ .else
-+ ldmib S!, {r1, r2}
-+ mov r0, r4, lsr #align*8
-+ ldmib S!, {r3, r4}
-+ orr r0, r0, r1, lsl #32-align*8
-+ mov r1, r1, lsr #align*8
-+ orr r1, r1, r2, lsl #32-align*8
-+ mov r2, r2, lsr #align*8
-+ orr r2, r2, r3, lsl #32-align*8
-+ mov r3, r3, lsr #align*8
-+ orr r3, r3, r4, lsl #32-align*8
-+ stmia D!, {r0, r1, r2, r3}
-+ .endif
-+ .elseif words == 8
-+ .if backwards
-+ ldmdb S!, {r4, r5, r6, r7}
-+ mov r8, r0, lsl #32-align*8
-+ ldmdb S!, {r0, r1, r2, r3}
-+ .if use_pld
-+ pld [S, OFF]
-+ .endif
-+ orr r8, r8, r7, lsr #align*8
-+ mov r7, r7, lsl #32-align*8
-+ orr r7, r7, r6, lsr #align*8
-+ mov r6, r6, lsl #32-align*8
-+ orr r6, r6, r5, lsr #align*8
-+ mov r5, r5, lsl #32-align*8
-+ orr r5, r5, r4, lsr #align*8
-+ mov r4, r4, lsl #32-align*8
-+ orr r4, r4, r3, lsr #align*8
-+ mov r3, r3, lsl #32-align*8
-+ orr r3, r3, r2, lsr #align*8
-+ mov r2, r2, lsl #32-align*8
-+ orr r2, r2, r1, lsr #align*8
-+ mov r1, r1, lsl #32-align*8
-+ orr r1, r1, r0, lsr #align*8
-+ stmdb D!, {r5, r6, r7, r8}
-+ stmdb D!, {r1, r2, r3, r4}
-+ .else
-+ ldmib S!, {r1, r2, r3, r4}
-+ mov r0, r8, lsr #align*8
-+ ldmib S!, {r5, r6, r7, r8}
-+ .if use_pld
-+ pld [S, OFF]
-+ .endif
-+ orr r0, r0, r1, lsl #32-align*8
-+ mov r1, r1, lsr #align*8
-+ orr r1, r1, r2, lsl #32-align*8
-+ mov r2, r2, lsr #align*8
-+ orr r2, r2, r3, lsl #32-align*8
-+ mov r3, r3, lsr #align*8
-+ orr r3, r3, r4, lsl #32-align*8
-+ mov r4, r4, lsr #align*8
-+ orr r4, r4, r5, lsl #32-align*8
-+ mov r5, r5, lsr #align*8
-+ orr r5, r5, r6, lsl #32-align*8
-+ mov r6, r6, lsr #align*8
-+ orr r6, r6, r7, lsl #32-align*8
-+ mov r7, r7, lsr #align*8
-+ orr r7, r7, r8, lsl #32-align*8
-+ stmia D!, {r0, r1, r2, r3}
-+ stmia D!, {r4, r5, r6, r7}
-+ .endif
-+ .endif
-+.endm
-+
-+.macro memcpy_leading_15bytes backwards, align
-+ movs DAT1, DAT2, lsl #31
-+ sub N, N, DAT2
-+ .if backwards
-+ ldrmib DAT0, [S, #-1]!
-+ ldrcsh DAT1, [S, #-2]!
-+ strmib DAT0, [D, #-1]!
-+ strcsh DAT1, [D, #-2]!
-+ .else
-+ ldrmib DAT0, [S], #1
-+ ldrcsh DAT1, [S], #2
-+ strmib DAT0, [D], #1
-+ strcsh DAT1, [D], #2
-+ .endif
-+ movs DAT1, DAT2, lsl #29
-+ .if backwards
-+ ldrmi DAT0, [S, #-4]!
-+ .if align == 0
-+ ldmcsdb S!, {DAT1, DAT2}
-+ .else
-+ ldrcs DAT2, [S, #-4]!
-+ ldrcs DAT1, [S, #-4]!
-+ .endif
-+ strmi DAT0, [D, #-4]!
-+ stmcsdb D!, {DAT1, DAT2}
-+ .else
-+ ldrmi DAT0, [S], #4
-+ .if align == 0
-+ ldmcsia S!, {DAT1, DAT2}
-+ .else
-+ ldrcs DAT1, [S], #4
-+ ldrcs DAT2, [S], #4
-+ .endif
-+ strmi DAT0, [D], #4
-+ stmcsia D!, {DAT1, DAT2}
-+ .endif
-+.endm
-+
-+.macro memcpy_trailing_15bytes backwards, align
-+ movs N, N, lsl #29
-+ .if backwards
-+ .if align == 0
-+ ldmcsdb S!, {DAT0, DAT1}
-+ .else
-+ ldrcs DAT1, [S, #-4]!
-+ ldrcs DAT0, [S, #-4]!
-+ .endif
-+ ldrmi DAT2, [S, #-4]!
-+ stmcsdb D!, {DAT0, DAT1}
-+ strmi DAT2, [D, #-4]!
-+ .else
-+ .if align == 0
-+ ldmcsia S!, {DAT0, DAT1}
-+ .else
-+ ldrcs DAT0, [S], #4
-+ ldrcs DAT1, [S], #4
-+ .endif
-+ ldrmi DAT2, [S], #4
-+ stmcsia D!, {DAT0, DAT1}
-+ strmi DAT2, [D], #4
-+ .endif
-+ movs N, N, lsl #2
-+ .if backwards
-+ ldrcsh DAT0, [S, #-2]!
-+ ldrmib DAT1, [S, #-1]
-+ strcsh DAT0, [D, #-2]!
-+ strmib DAT1, [D, #-1]
-+ .else
-+ ldrcsh DAT0, [S], #2
-+ ldrmib DAT1, [S]
-+ strcsh DAT0, [D], #2
-+ strmib DAT1, [D]
-+ .endif
-+.endm
-+
-+.macro memcpy_long_inner_loop backwards, align
-+ .if align != 0
-+ .if backwards
-+ ldr DAT0, [S, #-align]!
-+ .else
-+ ldr LAST, [S, #-align]!
-+ .endif
-+ .endif
-+110:
-+ .if align == 0
-+ .if backwards
-+ ldmdb S!, {DAT0, DAT1, DAT2, DAT3, DAT4, DAT5, DAT6, LAST}
-+ pld [S, OFF]
-+ stmdb D!, {DAT4, DAT5, DAT6, LAST}
-+ stmdb D!, {DAT0, DAT1, DAT2, DAT3}
-+ .else
-+ ldmia S!, {DAT0, DAT1, DAT2, DAT3, DAT4, DAT5, DAT6, LAST}
-+ pld [S, OFF]
-+ stmia D!, {DAT0, DAT1, DAT2, DAT3}
-+ stmia D!, {DAT4, DAT5, DAT6, LAST}
-+ .endif
-+ .else
-+ unaligned_words backwards, align, 1, 8, DAT0, DAT1, DAT2, DAT3, DAT4, DAT5, DAT6, DAT7, LAST
-+ .endif
-+ subs N, N, #32
-+ bhs 110b
-+ /* Just before the final (prefetch_distance+1) 32-byte blocks, deal with final preloads */
-+ preload_trailing backwards, S, N, OFF
-+ add N, N, #(prefetch_distance+2)*32 - 32
-+120:
-+ .if align == 0
-+ .if backwards
-+ ldmdb S!, {DAT0, DAT1, DAT2, DAT3, DAT4, DAT5, DAT6, LAST}
-+ stmdb D!, {DAT4, DAT5, DAT6, LAST}
-+ stmdb D!, {DAT0, DAT1, DAT2, DAT3}
-+ .else
-+ ldmia S!, {DAT0, DAT1, DAT2, DAT3, DAT4, DAT5, DAT6, LAST}
-+ stmia D!, {DAT0, DAT1, DAT2, DAT3}
-+ stmia D!, {DAT4, DAT5, DAT6, LAST}
-+ .endif
-+ .else
-+ unaligned_words backwards, align, 0, 8, DAT0, DAT1, DAT2, DAT3, DAT4, DAT5, DAT6, DAT7, LAST
-+ .endif
-+ subs N, N, #32
-+ bhs 120b
-+ tst N, #16
-+ .if align == 0
-+ .if backwards
-+ ldmnedb S!, {DAT0, DAT1, DAT2, LAST}
-+ stmnedb D!, {DAT0, DAT1, DAT2, LAST}
-+ .else
-+ ldmneia S!, {DAT0, DAT1, DAT2, LAST}
-+ stmneia D!, {DAT0, DAT1, DAT2, LAST}
-+ .endif
-+ .else
-+ beq 130f
-+ unaligned_words backwards, align, 0, 4, DAT0, DAT1, DAT2, DAT3, LAST
-+130:
-+ .endif
-+ /* Trailing words and bytes */
-+ tst N, #15
-+ beq 199f
-+ .if align != 0
-+ add S, S, #align
-+ .endif
-+ memcpy_trailing_15bytes backwards, align
-+199:
-+ pop {DAT3, DAT4, DAT5, DAT6, DAT7}
-+ pop {D, DAT1, DAT2, pc}
-+.endm
-+
-+.macro memcpy_medium_inner_loop backwards, align
-+120:
-+ .if backwards
-+ .if align == 0
-+ ldmdb S!, {DAT0, DAT1, DAT2, LAST}
-+ .else
-+ ldr LAST, [S, #-4]!
-+ ldr DAT2, [S, #-4]!
-+ ldr DAT1, [S, #-4]!
-+ ldr DAT0, [S, #-4]!
-+ .endif
-+ stmdb D!, {DAT0, DAT1, DAT2, LAST}
-+ .else
-+ .if align == 0
-+ ldmia S!, {DAT0, DAT1, DAT2, LAST}
-+ .else
-+ ldr DAT0, [S], #4
-+ ldr DAT1, [S], #4
-+ ldr DAT2, [S], #4
-+ ldr LAST, [S], #4
-+ .endif
-+ stmia D!, {DAT0, DAT1, DAT2, LAST}
-+ .endif
-+ subs N, N, #16
-+ bhs 120b
-+ /* Trailing words and bytes */
-+ tst N, #15
-+ beq 199f
-+ memcpy_trailing_15bytes backwards, align
-+199:
-+ pop {D, DAT1, DAT2, pc}
-+.endm
-+
-+.macro memcpy_short_inner_loop backwards, align
-+ tst N, #16
-+ .if backwards
-+ .if align == 0
-+ ldmnedb S!, {DAT0, DAT1, DAT2, LAST}
-+ .else
-+ ldrne LAST, [S, #-4]!
-+ ldrne DAT2, [S, #-4]!
-+ ldrne DAT1, [S, #-4]!
-+ ldrne DAT0, [S, #-4]!
-+ .endif
-+ stmnedb D!, {DAT0, DAT1, DAT2, LAST}
-+ .else
-+ .if align == 0
-+ ldmneia S!, {DAT0, DAT1, DAT2, LAST}
-+ .else
-+ ldrne DAT0, [S], #4
-+ ldrne DAT1, [S], #4
-+ ldrne DAT2, [S], #4
-+ ldrne LAST, [S], #4
-+ .endif
-+ stmneia D!, {DAT0, DAT1, DAT2, LAST}
-+ .endif
-+ memcpy_trailing_15bytes backwards, align
-+199:
-+ pop {D, DAT1, DAT2, pc}
-+.endm
-+
-+.macro memcpy backwards
-+ D .req a1
-+ S .req a2
-+ N .req a3
-+ DAT0 .req a4
-+ DAT1 .req v1
-+ DAT2 .req v2
-+ DAT3 .req v3
-+ DAT4 .req v4
-+ DAT5 .req v5
-+ DAT6 .req v6
-+ DAT7 .req sl
-+ LAST .req ip
-+ OFF .req lr
-+
-+ .cfi_startproc
-+
-+ push {D, DAT1, DAT2, lr}
-+
-+ .cfi_def_cfa_offset 16
-+ .cfi_rel_offset D, 0
-+ .cfi_undefined S
-+ .cfi_undefined N
-+ .cfi_undefined DAT0
-+ .cfi_rel_offset DAT1, 4
-+ .cfi_rel_offset DAT2, 8
-+ .cfi_undefined LAST
-+ .cfi_rel_offset lr, 12
-+
-+ .if backwards
-+ add D, D, N
-+ add S, S, N
-+ .endif
-+
-+ /* See if we're guaranteed to have at least one 16-byte aligned 16-byte write */
-+ cmp N, #31
-+ blo 170f
-+ /* To preload ahead as we go, we need at least (prefetch_distance+2) 32-byte blocks */
-+ cmp N, #(prefetch_distance+3)*32 - 1
-+ blo 160f
-+
-+ /* Long case */
-+ push {DAT3, DAT4, DAT5, DAT6, DAT7}
-+
-+ .cfi_def_cfa_offset 36
-+ .cfi_rel_offset D, 20
-+ .cfi_rel_offset DAT1, 24
-+ .cfi_rel_offset DAT2, 28
-+ .cfi_rel_offset DAT3, 0
-+ .cfi_rel_offset DAT4, 4
-+ .cfi_rel_offset DAT5, 8
-+ .cfi_rel_offset DAT6, 12
-+ .cfi_rel_offset DAT7, 16
-+ .cfi_rel_offset lr, 32
-+
-+ /* Adjust N so that the decrement instruction can also test for
-+ * inner loop termination. We want it to stop when there are
-+ * (prefetch_distance+1) complete blocks to go. */
-+ sub N, N, #(prefetch_distance+2)*32
-+ preload_leading_step1 backwards, DAT0, S
-+ .if backwards
-+ /* Bug in GAS: it accepts, but mis-assembles the instruction
-+ * ands DAT2, D, #60, 2
-+ * which sets DAT2 to the number of leading bytes until destination is aligned and also clears C (sets borrow)
-+ */
-+ .word 0xE210513C
-+ beq 154f
-+ .else
-+ ands DAT2, D, #15
-+ beq 154f
-+ rsb DAT2, DAT2, #16 /* number of leading bytes until destination aligned */
-+ .endif
-+ preload_leading_step2 backwards, DAT0, S, DAT2, OFF
-+ memcpy_leading_15bytes backwards, 1
-+154: /* Destination now 16-byte aligned; we have at least one prefetch as well as at least one 16-byte output block */
-+ /* Prefetch offset is best selected such that it lies in the first 8 of each 32 bytes - but it's just as easy to aim for the first one */
-+ .if backwards
-+ rsb OFF, S, #3
-+ and OFF, OFF, #28
-+ sub OFF, OFF, #32*(prefetch_distance+1)
-+ .else
-+ and OFF, S, #28
-+ rsb OFF, OFF, #32*prefetch_distance
-+ .endif
-+ movs DAT0, S, lsl #31
-+ bhi 157f
-+ bcs 156f
-+ bmi 155f
-+ memcpy_long_inner_loop backwards, 0
-+155: memcpy_long_inner_loop backwards, 1
-+156: memcpy_long_inner_loop backwards, 2
-+157: memcpy_long_inner_loop backwards, 3
-+
-+ .cfi_def_cfa_offset 16
-+ .cfi_rel_offset D, 0
-+ .cfi_rel_offset DAT1, 4
-+ .cfi_rel_offset DAT2, 8
-+ .cfi_same_value DAT3
-+ .cfi_same_value DAT4
-+ .cfi_same_value DAT5
-+ .cfi_same_value DAT6
-+ .cfi_same_value DAT7
-+ .cfi_rel_offset lr, 12
-+
-+160: /* Medium case */
-+ preload_all backwards, 0, 0, S, N, DAT2, OFF
-+ sub N, N, #16 /* simplifies inner loop termination */
-+ .if backwards
-+ ands DAT2, D, #15
-+ beq 164f
-+ .else
-+ ands DAT2, D, #15
-+ beq 164f
-+ rsb DAT2, DAT2, #16
-+ .endif
-+ memcpy_leading_15bytes backwards, align
-+164: /* Destination now 16-byte aligned; we have at least one 16-byte output block */
-+ tst S, #3
-+ bne 140f
-+ memcpy_medium_inner_loop backwards, 0
-+140: memcpy_medium_inner_loop backwards, 1
-+
-+170: /* Short case, less than 31 bytes, so no guarantee of at least one 16-byte block */
-+ teq N, #0
-+ beq 199f
-+ preload_all backwards, 1, 0, S, N, DAT2, LAST
-+ tst D, #3
-+ beq 174f
-+172: subs N, N, #1
-+ blo 199f
-+ .if backwards
-+ ldrb DAT0, [S, #-1]!
-+ strb DAT0, [D, #-1]!
-+ .else
-+ ldrb DAT0, [S], #1
-+ strb DAT0, [D], #1
-+ .endif
-+ tst D, #3
-+ bne 172b
-+174: /* Destination now 4-byte aligned; we have 0 or more output bytes to go */
-+ tst S, #3
-+ bne 140f
-+ memcpy_short_inner_loop backwards, 0
-+140: memcpy_short_inner_loop backwards, 1
-+
-+ .cfi_endproc
-+
-+ .unreq D
-+ .unreq S
-+ .unreq N
-+ .unreq DAT0
-+ .unreq DAT1
-+ .unreq DAT2
-+ .unreq DAT3
-+ .unreq DAT4
-+ .unreq DAT5
-+ .unreq DAT6
-+ .unreq DAT7
-+ .unreq LAST
-+ .unreq OFF
-+.endm
---- /dev/null
-+++ b/arch/arm/lib/memmove_rpi.S
-@@ -0,0 +1,61 @@
-+/*
-+Copyright (c) 2013, Raspberry Pi Foundation
-+Copyright (c) 2013, RISC OS Open Ltd
-+All rights reserved.
-+
-+Redistribution and use in source and binary forms, with or without
-+modification, are permitted provided that the following conditions are met:
-+ * Redistributions of source code must retain the above copyright
-+ notice, this list of conditions and the following disclaimer.
-+ * Redistributions in binary form must reproduce the above copyright
-+ notice, this list of conditions and the following disclaimer in the
-+ documentation and/or other materials provided with the distribution.
-+ * Neither the name of the copyright holder nor the
-+ names of its contributors may be used to endorse or promote products
-+ derived from this software without specific prior written permission.
-+
-+THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND
-+ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
-+WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
-+DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY
-+DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
-+LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
-+ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
-+(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+*/
-+
-+#include <linux/linkage.h>
-+#include "arm-mem.h"
-+#include "memcpymove.h"
-+
-+/* Prevent the stack from becoming executable */
-+#if defined(__linux__) && defined(__ELF__)
-+.section .note.GNU-stack,"",%progbits
-+#endif
-+
-+ .text
-+ .arch armv6
-+ .object_arch armv4
-+ .arm
-+ .altmacro
-+ .p2align 2
-+
-+/*
-+ * void *memmove(void *s1, const void *s2, size_t n);
-+ * On entry:
-+ * a1 = pointer to destination
-+ * a2 = pointer to source
-+ * a3 = number of bytes to copy
-+ * On exit:
-+ * a1 preserved
-+ */
-+
-+.set prefetch_distance, 3
-+
-+ENTRY(memmove)
-+ cmp a2, a1
-+ bpl memcpy /* pl works even over -1 - 0 and 0x7fffffff - 0x80000000 boundaries */
-+ memcpy 1
-+ENDPROC(memmove)
---- /dev/null
-+++ b/arch/arm/lib/memset_rpi.S
-@@ -0,0 +1,123 @@
-+/*
-+Copyright (c) 2013, Raspberry Pi Foundation
-+Copyright (c) 2013, RISC OS Open Ltd
-+All rights reserved.
-+
-+Redistribution and use in source and binary forms, with or without
-+modification, are permitted provided that the following conditions are met:
-+ * Redistributions of source code must retain the above copyright
-+ notice, this list of conditions and the following disclaimer.
-+ * Redistributions in binary form must reproduce the above copyright
-+ notice, this list of conditions and the following disclaimer in the
-+ documentation and/or other materials provided with the distribution.
-+ * Neither the name of the copyright holder nor the
-+ names of its contributors may be used to endorse or promote products
-+ derived from this software without specific prior written permission.
-+
-+THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND
-+ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
-+WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
-+DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY
-+DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-+(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
-+LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
-+ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
-+(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-+SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-+*/
-+
-+#include <linux/linkage.h>
-+#include "arm-mem.h"
-+
-+/* Prevent the stack from becoming executable */
-+#if defined(__linux__) && defined(__ELF__)
-+.section .note.GNU-stack,"",%progbits
-+#endif
-+
-+ .text
-+ .arch armv6
-+ .object_arch armv4
-+ .arm
-+ .altmacro
-+ .p2align 2
-+
-+/*
-+ * void *memset(void *s, int c, size_t n);
-+ * On entry:
-+ * a1 = pointer to buffer to fill
-+ * a2 = byte pattern to fill with (caller-narrowed)
-+ * a3 = number of bytes to fill
-+ * On exit:
-+ * a1 preserved
-+ */
-+ENTRY(mmioset)
-+ENTRY(memset)
-+ S .req a1
-+ DAT0 .req a2
-+ N .req a3
-+ DAT1 .req a4
-+ DAT2 .req ip
-+ DAT3 .req lr
-+
-+ orr DAT0, DAT0, lsl #8
-+ push {S, lr}
-+ orr DAT0, DAT0, lsl #16
-+ mov DAT1, DAT0
-+
-+ /* See if we're guaranteed to have at least one 16-byte aligned 16-byte write */
-+ cmp N, #31
-+ blo 170f
-+
-+161: sub N, N, #16 /* simplifies inner loop termination */
-+ /* Leading words and bytes */
-+ tst S, #15
-+ beq 164f
-+ rsb DAT3, S, #0 /* bits 0-3 = number of leading bytes until aligned */
-+ movs DAT2, DAT3, lsl #31
-+ submi N, N, #1
-+ strmib DAT0, [S], #1
-+ subcs N, N, #2
-+ strcsh DAT0, [S], #2
-+ movs DAT2, DAT3, lsl #29
-+ submi N, N, #4
-+ strmi DAT0, [S], #4
-+ subcs N, N, #8
-+ stmcsia S!, {DAT0, DAT1}
-+164: /* Delayed set up of DAT2 and DAT3 so we could use them as scratch registers above */
-+ mov DAT2, DAT0
-+ mov DAT3, DAT0
-+ /* Now the inner loop of 16-byte stores */
-+165: stmia S!, {DAT0, DAT1, DAT2, DAT3}
-+ subs N, N, #16
-+ bhs 165b
-+166: /* Trailing words and bytes */
-+ movs N, N, lsl #29
-+ stmcsia S!, {DAT0, DAT1}
-+ strmi DAT0, [S], #4
-+ movs N, N, lsl #2
-+ strcsh DAT0, [S], #2
-+ strmib DAT0, [S]
-+199: pop {S, pc}
-+
-+170: /* Short case */
-+ mov DAT2, DAT0
-+ mov DAT3, DAT0
-+ tst S, #3
-+ beq 174f
-+172: subs N, N, #1
-+ blo 199b
-+ strb DAT0, [S], #1
-+ tst S, #3
-+ bne 172b
-+174: tst N, #16
-+ stmneia S!, {DAT0, DAT1, DAT2, DAT3}
-+ b 166b
-+
-+ .unreq S
-+ .unreq DAT0
-+ .unreq N
-+ .unreq DAT1
-+ .unreq DAT2
-+ .unreq DAT3
-+ENDPROC(memset)
-+ENDPROC(mmioset)
---- a/arch/arm/lib/uaccess_with_memcpy.c
-+++ b/arch/arm/lib/uaccess_with_memcpy.c
-@@ -22,6 +22,14 @@
- #include <asm/current.h>
- #include <asm/page.h>
-
-+#ifndef COPY_FROM_USER_THRESHOLD
-+#define COPY_FROM_USER_THRESHOLD 64
-+#endif
-+
-+#ifndef COPY_TO_USER_THRESHOLD
-+#define COPY_TO_USER_THRESHOLD 64
-+#endif
-+
- static int
- pin_page_for_write(const void __user *_addr, pte_t **ptep, spinlock_t **ptlp)
- {
-@@ -85,7 +93,44 @@ pin_page_for_write(const void __user *_a
- return 1;
- }
-
--static unsigned long noinline
-+static int
-+pin_page_for_read(const void __user *_addr, pte_t **ptep, spinlock_t **ptlp)
-+{
-+ unsigned long addr = (unsigned long)_addr;
-+ pgd_t *pgd;
-+ pmd_t *pmd;
-+ pte_t *pte;
-+ pud_t *pud;
-+ spinlock_t *ptl;
-+
-+ pgd = pgd_offset(current->mm, addr);
-+ if (unlikely(pgd_none(*pgd) || pgd_bad(*pgd)))
-+ {
-+ return 0;
-+ }
-+ pud = pud_offset(pgd, addr);
-+ if (unlikely(pud_none(*pud) || pud_bad(*pud)))
-+ {
-+ return 0;
-+ }
-+
-+ pmd = pmd_offset(pud, addr);
-+ if (unlikely(pmd_none(*pmd) || pmd_bad(*pmd)))
-+ return 0;
-+
-+ pte = pte_offset_map_lock(current->mm, pmd, addr, &ptl);
-+ if (unlikely(!pte_present(*pte) || !pte_young(*pte))) {
-+ pte_unmap_unlock(pte, ptl);
-+ return 0;
-+ }
-+
-+ *ptep = pte;
-+ *ptlp = ptl;
-+
-+ return 1;
-+}
-+
-+unsigned long noinline
- __copy_to_user_memcpy(void __user *to, const void *from, unsigned long n)
- {
- unsigned long ua_flags;
-@@ -138,6 +183,54 @@ out:
- return n;
- }
-
-+unsigned long noinline
-+__copy_from_user_memcpy(void *to, const void __user *from, unsigned long n)
-+{
-+ int atomic;
-+
-+ if (unlikely(segment_eq(get_fs(), KERNEL_DS))) {
-+ memcpy(to, (const void *)from, n);
-+ return 0;
-+ }
-+
-+ /* the mmap semaphore is taken only if not in an atomic context */
-+ atomic = in_atomic();
-+
-+ if (!atomic)
-+ down_read(¤t->mm->mmap_sem);
-+ while (n) {
-+ pte_t *pte;
-+ spinlock_t *ptl;
-+ int tocopy;
-+
-+ while (!pin_page_for_read(from, &pte, &ptl)) {
-+ char temp;
-+ if (!atomic)
-+ up_read(¤t->mm->mmap_sem);
-+ if (__get_user(temp, (char __user *)from))
-+ goto out;
-+ if (!atomic)
-+ down_read(¤t->mm->mmap_sem);
-+ }
-+
-+ tocopy = (~(unsigned long)from & ~PAGE_MASK) + 1;
-+ if (tocopy > n)
-+ tocopy = n;
-+
-+ memcpy(to, (const void *)from, tocopy);
-+ to += tocopy;
-+ from += tocopy;
-+ n -= tocopy;
-+
-+ pte_unmap_unlock(pte, ptl);
-+ }
-+ if (!atomic)
-+ up_read(¤t->mm->mmap_sem);
-+
-+out:
-+ return n;
-+}
-+
- unsigned long
- arm_copy_to_user(void __user *to, const void *from, unsigned long n)
- {
-@@ -148,7 +241,7 @@ arm_copy_to_user(void __user *to, const
- * With frame pointer disabled, tail call optimization kicks in
- * as well making this test almost invisible.
- */
-- if (n < 64) {
-+ if (n < COPY_TO_USER_THRESHOLD) {
- unsigned long ua_flags = uaccess_save_and_enable();
- n = __copy_to_user_std(to, from, n);
- uaccess_restore(ua_flags);
-@@ -157,6 +250,21 @@ arm_copy_to_user(void __user *to, const
- }
- return n;
- }
-+
-+unsigned long __must_check
-+arm_copy_from_user(void *to, const void __user *from, unsigned long n)
-+{
-+ /*
-+ * This test is stubbed out of the main function above to keep
-+ * the overhead for small copies low by avoiding a large
-+ * register dump on the stack just to reload them right away.
-+ * With frame pointer disabled, tail call optimization kicks in
-+ * as well making this test almost invisible.
-+ */
-+ if (n < COPY_FROM_USER_THRESHOLD)
-+ return __copy_from_user_std(to, from, n);
-+ return __copy_from_user_memcpy(to, from, n);
-+}
-
- static unsigned long noinline
- __clear_user_memset(void __user *addr, unsigned long n)
diff --git a/target/linux/brcm2708/patches-4.4/0080-gpio-poweroff-Allow-it-to-work-on-Raspberry-Pi.patch b/target/linux/brcm2708/patches-4.4/0080-gpio-poweroff-Allow-it-to-work-on-Raspberry-Pi.patch
deleted file mode 100644
index 13b2b4b..0000000
--- a/target/linux/brcm2708/patches-4.4/0080-gpio-poweroff-Allow-it-to-work-on-Raspberry-Pi.patch
+++ /dev/null
@@ -1,35 +0,0 @@
-From e1bd8231e59c90e284ddfcd9380792b40f775b1d Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Thu, 25 Jun 2015 12:16:11 +0100
-Subject: [PATCH] gpio-poweroff: Allow it to work on Raspberry Pi
-
-The Raspberry Pi firmware manages the power-down and reboot
-process. To do this it installs a pm_power_off handler, causing
-the gpio-poweroff module to abort the probe function.
-
-This patch introduces a "force" DT property that overrides that
-behaviour, and also adds a DT overlay to enable and control it.
-
-Note that running in an active-low configuration (DT parameter
-"active_low") requires a custom dt-blob.bin and probably won't
-allow a reboot without switching off, so an external inversion
-of the trigger signal may be preferable.
----
- drivers/power/reset/gpio-poweroff.c | 4 +++-
- 1 file changed, 3 insertions(+), 1 deletion(-)
-
---- a/drivers/power/reset/gpio-poweroff.c
-+++ b/drivers/power/reset/gpio-poweroff.c
-@@ -49,9 +49,11 @@ static int gpio_poweroff_probe(struct pl
- {
- bool input = false;
- enum gpiod_flags flags;
-+ bool force = false;
-
- /* If a pm_power_off function has already been added, leave it alone */
-- if (pm_power_off != NULL) {
-+ force = of_property_read_bool(pdev->dev.of_node, "force");
-+ if (!force && (pm_power_off != NULL)) {
- dev_err(&pdev->dev,
- "%s: pm_power_off function already registered",
- __func__);
diff --git a/target/linux/brcm2708/patches-4.4/0081-spidev-Add-spidev-compatible-string-to-silence-warni.patch b/target/linux/brcm2708/patches-4.4/0081-spidev-Add-spidev-compatible-string-to-silence-warni.patch
deleted file mode 100644
index 2cbf84e..0000000
--- a/target/linux/brcm2708/patches-4.4/0081-spidev-Add-spidev-compatible-string-to-silence-warni.patch
+++ /dev/null
@@ -1,20 +0,0 @@
-From 7db6255f0e09c3744d39871a8b86fdf3ab94675d Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Tue, 14 Jul 2015 10:26:09 +0100
-Subject: [PATCH] spidev: Add "spidev" compatible string to silence warning
-
-See: https://github.com/raspberrypi/linux/issues/1054
----
- drivers/spi/spidev.c | 1 +
- 1 file changed, 1 insertion(+)
-
---- a/drivers/spi/spidev.c
-+++ b/drivers/spi/spidev.c
-@@ -696,6 +696,7 @@ static const struct of_device_id spidev_
- { .compatible = "rohm,dh2228fv" },
- { .compatible = "lineartechnology,ltc2488" },
- { .compatible = "siliconlabs,si3210" },
-+ { .compatible = "spidev" },
- {},
- };
- MODULE_DEVICE_TABLE(of, spidev_dt_ids);
diff --git a/target/linux/brcm2708/patches-4.4/0082-scripts-dtc-Add-overlay-support.patch b/target/linux/brcm2708/patches-4.4/0082-scripts-dtc-Add-overlay-support.patch
deleted file mode 100644
index ad70a1d..0000000
--- a/target/linux/brcm2708/patches-4.4/0082-scripts-dtc-Add-overlay-support.patch
+++ /dev/null
@@ -1,4389 +0,0 @@
-From acee2987cefc8407c1883375f494a37b39ac1309 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Tue, 14 Jul 2015 17:00:18 +0100
-Subject: [PATCH] scripts/dtc: Add overlay support
-
----
- scripts/dtc/checks.c | 119 ++-
- scripts/dtc/dtc-lexer.l | 5 +
- scripts/dtc/dtc-lexer.lex.c_shipped | 490 ++++-----
- scripts/dtc/dtc-parser.tab.c_shipped | 1896 +++++++++++++++++++---------------
- scripts/dtc/dtc-parser.tab.h_shipped | 107 +-
- scripts/dtc/dtc-parser.y | 23 +-
- scripts/dtc/dtc.c | 9 +-
- scripts/dtc/dtc.h | 38 +
- scripts/dtc/flattree.c | 141 ++-
- scripts/dtc/version_gen.h | 2 +-
- 10 files changed, 1685 insertions(+), 1145 deletions(-)
-
---- a/scripts/dtc/checks.c
-+++ b/scripts/dtc/checks.c
-@@ -458,21 +458,91 @@ static void fixup_phandle_references(str
- struct node *node, struct property *prop)
- {
- struct marker *m = prop->val.markers;
-+ struct fixup *f, **fp;
-+ struct fixup_entry *fe, **fep;
- struct node *refnode;
- cell_t phandle;
-+ int has_phandle_refs;
-+
-+ has_phandle_refs = 0;
-+ for_each_marker_of_type(m, REF_PHANDLE) {
-+ has_phandle_refs = 1;
-+ break;
-+ }
-+
-+ if (!has_phandle_refs)
-+ return;
-
- for_each_marker_of_type(m, REF_PHANDLE) {
- assert(m->offset + sizeof(cell_t) <= prop->val.len);
-
- refnode = get_node_by_ref(dt, m->ref);
-- if (! refnode) {
-+ if (!refnode && !symbol_fixup_support) {
- FAIL(c, "Reference to non-existent node or label \"%s\"\n",
-- m->ref);
-+ m->ref);
- continue;
- }
-
-- phandle = get_node_phandle(dt, refnode);
-- *((cell_t *)(prop->val.val + m->offset)) = cpu_to_fdt32(phandle);
-+ if (!refnode) {
-+ /* allocate fixup entry */
-+ fe = xmalloc(sizeof(*fe));
-+
-+ fe->node = node;
-+ fe->prop = prop;
-+ fe->offset = m->offset;
-+ fe->next = NULL;
-+
-+ /* search for an already existing fixup */
-+ for_each_fixup(dt, f)
-+ if (strcmp(f->ref, m->ref) == 0)
-+ break;
-+
-+ /* no fixup found, add new */
-+ if (f == NULL) {
-+ f = xmalloc(sizeof(*f));
-+ f->ref = m->ref;
-+ f->entries = NULL;
-+ f->next = NULL;
-+
-+ /* add it to the tree */
-+ fp = &dt->fixups;
-+ while (*fp)
-+ fp = &(*fp)->next;
-+ *fp = f;
-+ }
-+
-+ /* and now append fixup entry */
-+ fep = &f->entries;
-+ while (*fep)
-+ fep = &(*fep)->next;
-+ *fep = fe;
-+
-+ /* mark the entry as unresolved */
-+ phandle = 0xdeadbeef;
-+ } else {
-+ phandle = get_node_phandle(dt, refnode);
-+
-+ /* if it's a plugin, we need to record it */
-+ if (symbol_fixup_support && dt->is_plugin) {
-+
-+ /* allocate a new local fixup entry */
-+ fe = xmalloc(sizeof(*fe));
-+
-+ fe->node = node;
-+ fe->prop = prop;
-+ fe->offset = m->offset;
-+ fe->next = NULL;
-+
-+ /* append it to the local fixups */
-+ fep = &dt->local_fixups;
-+ while (*fep)
-+ fep = &(*fep)->next;
-+ *fep = fe;
-+ }
-+ }
-+
-+ *((cell_t *)(prop->val.val + m->offset)) =
-+ cpu_to_fdt32(phandle);
- }
- }
- ERROR(phandle_references, NULL, NULL, fixup_phandle_references, NULL,
-@@ -652,6 +722,45 @@ static void check_obsolete_chosen_interr
- }
- TREE_WARNING(obsolete_chosen_interrupt_controller, NULL);
-
-+static void check_auto_label_phandles(struct check *c, struct node *dt,
-+ struct node *node)
-+{
-+ struct label *l;
-+ struct symbol *s, **sp;
-+ int has_label;
-+
-+ if (!symbol_fixup_support)
-+ return;
-+
-+ has_label = 0;
-+ for_each_label(node->labels, l) {
-+ has_label = 1;
-+ break;
-+ }
-+
-+ if (!has_label)
-+ return;
-+
-+ /* force allocation of a phandle for this node */
-+ (void)get_node_phandle(dt, node);
-+
-+ /* add the symbol */
-+ for_each_label(node->labels, l) {
-+
-+ s = xmalloc(sizeof(*s));
-+ s->label = l;
-+ s->node = node;
-+ s->next = NULL;
-+
-+ /* add it to the symbols list */
-+ sp = &dt->symbols;
-+ while (*sp)
-+ sp = &((*sp)->next);
-+ *sp = s;
-+ }
-+}
-+NODE_WARNING(auto_label_phandles, NULL);
-+
- static struct check *check_table[] = {
- &duplicate_node_names, &duplicate_property_names,
- &node_name_chars, &node_name_format, &property_name_chars,
-@@ -670,6 +779,8 @@ static struct check *check_table[] = {
- &avoid_default_addr_size,
- &obsolete_chosen_interrupt_controller,
-
-+ &auto_label_phandles,
-+
- &always_fail,
- };
-
---- a/scripts/dtc/dtc-lexer.l
-+++ b/scripts/dtc/dtc-lexer.l
-@@ -113,6 +113,11 @@ static void lexical_error(const char *fm
- return DT_V1;
- }
-
-+<*>"/plugin/" {
-+ DPRINT("Keyword: /plugin/\n");
-+ return DT_PLUGIN;
-+ }
-+
- <*>"/memreserve/" {
- DPRINT("Keyword: /memreserve/\n");
- BEGIN_DEFAULT();
---- a/scripts/dtc/dtc-lexer.lex.c_shipped
-+++ b/scripts/dtc/dtc-lexer.lex.c_shipped
-@@ -9,7 +9,7 @@
- #define FLEX_SCANNER
- #define YY_FLEX_MAJOR_VERSION 2
- #define YY_FLEX_MINOR_VERSION 5
--#define YY_FLEX_SUBMINOR_VERSION 39
-+#define YY_FLEX_SUBMINOR_VERSION 35
- #if YY_FLEX_SUBMINOR_VERSION > 0
- #define FLEX_BETA
- #endif
-@@ -162,12 +162,7 @@ typedef unsigned int flex_uint32_t;
- typedef struct yy_buffer_state *YY_BUFFER_STATE;
- #endif
-
--#ifndef YY_TYPEDEF_YY_SIZE_T
--#define YY_TYPEDEF_YY_SIZE_T
--typedef size_t yy_size_t;
--#endif
--
--extern yy_size_t yyleng;
-+extern int yyleng;
-
- extern FILE *yyin, *yyout;
-
-@@ -176,7 +171,6 @@ extern FILE *yyin, *yyout;
- #define EOB_ACT_LAST_MATCH 2
-
- #define YY_LESS_LINENO(n)
-- #define YY_LINENO_REWIND_TO(ptr)
-
- /* Return all but the first "n" matched characters back to the input stream. */
- #define yyless(n) \
-@@ -194,6 +188,11 @@ extern FILE *yyin, *yyout;
-
- #define unput(c) yyunput( c, (yytext_ptr) )
-
-+#ifndef YY_TYPEDEF_YY_SIZE_T
-+#define YY_TYPEDEF_YY_SIZE_T
-+typedef size_t yy_size_t;
-+#endif
-+
- #ifndef YY_STRUCT_YY_BUFFER_STATE
- #define YY_STRUCT_YY_BUFFER_STATE
- struct yy_buffer_state
-@@ -211,7 +210,7 @@ struct yy_buffer_state
- /* Number of characters read into yy_ch_buf, not including EOB
- * characters.
- */
-- yy_size_t yy_n_chars;
-+ int yy_n_chars;
-
- /* Whether we "own" the buffer - i.e., we know we created it,
- * and can realloc() it to grow it, and should free() it to
-@@ -281,8 +280,8 @@ static YY_BUFFER_STATE * yy_buffer_stack
-
- /* yy_hold_char holds the character lost when yytext is formed. */
- static char yy_hold_char;
--static yy_size_t yy_n_chars; /* number of characters read into yy_ch_buf */
--yy_size_t yyleng;
-+static int yy_n_chars; /* number of characters read into yy_ch_buf */
-+int yyleng;
-
- /* Points to current character in buffer. */
- static char *yy_c_buf_p = (char *) 0;
-@@ -310,7 +309,7 @@ static void yy_init_buffer (YY_BUFFER_ST
-
- YY_BUFFER_STATE yy_scan_buffer (char *base,yy_size_t size );
- YY_BUFFER_STATE yy_scan_string (yyconst char *yy_str );
--YY_BUFFER_STATE yy_scan_bytes (yyconst char *bytes,yy_size_t len );
-+YY_BUFFER_STATE yy_scan_bytes (yyconst char *bytes,int len );
-
- void *yyalloc (yy_size_t );
- void *yyrealloc (void *,yy_size_t );
-@@ -342,7 +341,7 @@ void yyfree (void * );
-
- /* Begin user sect3 */
-
--#define yywrap() 1
-+#define yywrap(n) 1
- #define YY_SKIP_YYWRAP
-
- typedef unsigned char YY_CHAR;
-@@ -373,8 +372,8 @@ static void yy_fatal_error (yyconst char
- *yy_cp = '\0'; \
- (yy_c_buf_p) = yy_cp;
-
--#define YY_NUM_RULES 30
--#define YY_END_OF_BUFFER 31
-+#define YY_NUM_RULES 31
-+#define YY_END_OF_BUFFER 32
- /* This struct is not used in this scanner,
- but its presence is necessary. */
- struct yy_trans_info
-@@ -382,25 +381,26 @@ struct yy_trans_info
- flex_int32_t yy_verify;
- flex_int32_t yy_nxt;
- };
--static yyconst flex_int16_t yy_accept[159] =
-+static yyconst flex_int16_t yy_accept[166] =
- { 0,
-- 0, 0, 0, 0, 0, 0, 0, 0, 31, 29,
-- 18, 18, 29, 29, 29, 29, 29, 29, 29, 29,
-- 29, 29, 29, 29, 29, 29, 15, 16, 16, 29,
-- 16, 10, 10, 18, 26, 0, 3, 0, 27, 12,
-- 0, 0, 11, 0, 0, 0, 0, 0, 0, 0,
-- 21, 23, 25, 24, 22, 0, 9, 28, 0, 0,
-- 0, 14, 14, 16, 16, 16, 10, 10, 10, 0,
-- 12, 0, 11, 0, 0, 0, 20, 0, 0, 0,
-- 0, 0, 0, 0, 0, 16, 10, 10, 10, 0,
-- 13, 19, 0, 0, 0, 0, 0, 0, 0, 0,
--
-- 0, 16, 0, 0, 0, 0, 0, 0, 0, 0,
-- 0, 16, 6, 0, 0, 0, 0, 0, 0, 2,
-- 0, 0, 0, 0, 0, 0, 0, 0, 4, 17,
-- 0, 0, 2, 0, 0, 0, 0, 0, 0, 0,
-- 0, 0, 0, 0, 0, 1, 0, 0, 0, 0,
-- 5, 8, 0, 0, 0, 0, 7, 0
-+ 0, 0, 0, 0, 0, 0, 0, 0, 32, 30,
-+ 19, 19, 30, 30, 30, 30, 30, 30, 30, 30,
-+ 30, 30, 30, 30, 30, 30, 16, 17, 17, 30,
-+ 17, 11, 11, 19, 27, 0, 3, 0, 28, 13,
-+ 0, 0, 12, 0, 0, 0, 0, 0, 0, 0,
-+ 0, 22, 24, 26, 25, 23, 0, 10, 29, 0,
-+ 0, 0, 15, 15, 17, 17, 17, 11, 11, 11,
-+ 0, 13, 0, 12, 0, 0, 0, 21, 0, 0,
-+ 0, 0, 0, 0, 0, 0, 0, 17, 11, 11,
-+ 11, 0, 14, 20, 0, 0, 0, 0, 0, 0,
-+
-+ 0, 0, 0, 0, 17, 0, 0, 0, 0, 0,
-+ 0, 0, 0, 0, 0, 17, 7, 0, 0, 0,
-+ 0, 0, 0, 0, 2, 0, 0, 0, 0, 0,
-+ 0, 0, 0, 0, 4, 18, 0, 0, 5, 2,
-+ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
-+ 0, 0, 1, 0, 0, 0, 0, 6, 9, 0,
-+ 0, 0, 0, 8, 0
- } ;
-
- static yyconst flex_int32_t yy_ec[256] =
-@@ -416,9 +416,9 @@ static yyconst flex_int32_t yy_ec[256] =
- 22, 22, 22, 22, 24, 22, 22, 25, 22, 22,
- 1, 26, 27, 1, 22, 1, 21, 28, 29, 30,
-
-- 31, 21, 22, 22, 32, 22, 22, 33, 34, 35,
-- 36, 37, 22, 38, 39, 40, 41, 42, 22, 25,
-- 43, 22, 44, 45, 46, 1, 1, 1, 1, 1,
-+ 31, 21, 32, 22, 33, 22, 22, 34, 35, 36,
-+ 37, 38, 22, 39, 40, 41, 42, 43, 22, 25,
-+ 44, 22, 45, 46, 47, 1, 1, 1, 1, 1,
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
-@@ -435,163 +435,165 @@ static yyconst flex_int32_t yy_ec[256] =
- 1, 1, 1, 1, 1
- } ;
-
--static yyconst flex_int32_t yy_meta[47] =
-+static yyconst flex_int32_t yy_meta[48] =
- { 0,
- 1, 1, 1, 1, 1, 1, 2, 3, 1, 2,
- 2, 2, 4, 5, 5, 5, 6, 1, 1, 1,
- 7, 8, 8, 8, 8, 1, 1, 7, 7, 7,
- 7, 8, 8, 8, 8, 8, 8, 8, 8, 8,
-- 8, 8, 8, 3, 1, 4
-+ 8, 8, 8, 8, 3, 1, 4
- } ;
-
--static yyconst flex_int16_t yy_base[173] =
-+static yyconst flex_int16_t yy_base[180] =
- { 0,
-- 0, 383, 34, 382, 65, 381, 37, 105, 387, 391,
-- 54, 111, 367, 110, 109, 109, 112, 41, 366, 104,
-- 367, 338, 124, 117, 0, 144, 391, 0, 121, 0,
-- 135, 155, 140, 179, 391, 160, 391, 379, 391, 0,
-- 368, 141, 391, 167, 370, 376, 346, 103, 342, 345,
-- 391, 391, 391, 391, 391, 358, 391, 391, 175, 342,
-- 338, 391, 355, 0, 185, 339, 184, 347, 346, 0,
-- 0, 322, 175, 357, 175, 363, 352, 324, 330, 323,
-- 332, 326, 201, 324, 329, 322, 391, 333, 181, 309,
-- 391, 341, 340, 313, 320, 338, 178, 311, 146, 317,
--
-- 314, 315, 335, 331, 303, 300, 309, 299, 308, 188,
-- 336, 335, 391, 305, 320, 281, 283, 271, 203, 288,
-- 281, 271, 266, 264, 245, 242, 208, 104, 391, 391,
-- 244, 218, 204, 219, 206, 224, 201, 212, 204, 229,
-- 215, 208, 207, 200, 219, 391, 233, 221, 200, 181,
-- 391, 391, 149, 122, 86, 41, 391, 391, 245, 251,
-- 259, 263, 267, 273, 280, 284, 292, 300, 304, 310,
-- 318, 326
-+ 0, 393, 35, 392, 66, 391, 38, 107, 397, 401,
-+ 55, 113, 377, 112, 111, 111, 114, 42, 376, 106,
-+ 377, 347, 126, 120, 0, 147, 401, 0, 124, 0,
-+ 137, 158, 170, 163, 401, 153, 401, 389, 401, 0,
-+ 378, 120, 401, 131, 380, 386, 355, 139, 351, 355,
-+ 351, 401, 401, 401, 401, 401, 367, 401, 401, 185,
-+ 350, 346, 401, 364, 0, 185, 347, 189, 356, 355,
-+ 0, 0, 330, 180, 366, 141, 372, 361, 332, 338,
-+ 331, 341, 334, 326, 205, 331, 337, 329, 401, 341,
-+ 167, 316, 401, 349, 348, 320, 328, 346, 180, 318,
-+
-+ 324, 209, 324, 320, 322, 342, 338, 309, 306, 315,
-+ 305, 315, 312, 192, 342, 341, 401, 293, 306, 282,
-+ 268, 252, 255, 203, 285, 282, 272, 268, 252, 233,
-+ 232, 239, 208, 107, 401, 401, 238, 211, 401, 211,
-+ 212, 208, 228, 203, 215, 207, 233, 222, 212, 211,
-+ 203, 227, 401, 237, 225, 204, 185, 401, 401, 149,
-+ 128, 88, 42, 401, 401, 253, 259, 267, 271, 275,
-+ 281, 288, 292, 300, 308, 312, 318, 326, 334
- } ;
-
--static yyconst flex_int16_t yy_def[173] =
-+static yyconst flex_int16_t yy_def[180] =
- { 0,
-- 158, 1, 1, 3, 158, 5, 1, 1, 158, 158,
-- 158, 158, 158, 159, 160, 161, 158, 158, 158, 158,
-- 162, 158, 158, 158, 163, 162, 158, 164, 165, 164,
-- 164, 158, 158, 158, 158, 159, 158, 159, 158, 166,
-- 158, 161, 158, 161, 167, 168, 158, 158, 158, 158,
-- 158, 158, 158, 158, 158, 162, 158, 158, 158, 158,
-- 158, 158, 162, 164, 165, 164, 158, 158, 158, 169,
-- 166, 170, 161, 167, 167, 168, 158, 158, 158, 158,
-- 158, 158, 158, 158, 158, 164, 158, 158, 169, 170,
-- 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
--
-- 158, 164, 158, 158, 158, 158, 158, 158, 158, 171,
-- 158, 164, 158, 158, 158, 158, 158, 158, 171, 158,
-- 171, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-- 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-- 172, 158, 158, 158, 172, 158, 172, 158, 158, 158,
-- 158, 158, 158, 158, 158, 158, 158, 0, 158, 158,
-- 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-- 158, 158
-+ 165, 1, 1, 3, 165, 5, 1, 1, 165, 165,
-+ 165, 165, 165, 166, 167, 168, 165, 165, 165, 165,
-+ 169, 165, 165, 165, 170, 169, 165, 171, 172, 171,
-+ 171, 165, 165, 165, 165, 166, 165, 166, 165, 173,
-+ 165, 168, 165, 168, 174, 175, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 169, 165, 165, 165,
-+ 165, 165, 165, 169, 171, 172, 171, 165, 165, 165,
-+ 176, 173, 177, 168, 174, 174, 175, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 165, 171, 165, 165,
-+ 176, 177, 165, 165, 165, 165, 165, 165, 165, 165,
-+
-+ 165, 165, 165, 165, 171, 165, 165, 165, 165, 165,
-+ 165, 165, 165, 178, 165, 171, 165, 165, 165, 165,
-+ 165, 165, 165, 178, 165, 178, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 165, 179, 165, 165,
-+ 165, 179, 165, 179, 165, 165, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 0, 165, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 165, 165, 165
- } ;
-
--static yyconst flex_int16_t yy_nxt[438] =
-+static yyconst flex_int16_t yy_nxt[449] =
- { 0,
- 10, 11, 12, 11, 13, 14, 10, 15, 16, 10,
- 10, 10, 17, 10, 10, 10, 10, 18, 19, 20,
- 21, 21, 21, 21, 21, 10, 10, 21, 21, 21,
- 21, 21, 21, 21, 21, 21, 21, 21, 21, 21,
-- 21, 21, 21, 10, 22, 10, 24, 25, 25, 25,
-- 32, 33, 33, 157, 26, 34, 34, 34, 51, 52,
-- 27, 26, 26, 26, 26, 10, 11, 12, 11, 13,
-- 14, 28, 15, 16, 28, 28, 28, 24, 28, 28,
-- 28, 10, 18, 19, 20, 29, 29, 29, 29, 29,
-- 30, 10, 29, 29, 29, 29, 29, 29, 29, 29,
--
-- 29, 29, 29, 29, 29, 29, 29, 29, 10, 22,
-- 10, 23, 34, 34, 34, 37, 39, 43, 32, 33,
-- 33, 45, 54, 55, 46, 59, 45, 64, 156, 46,
-- 64, 64, 64, 79, 44, 38, 59, 57, 134, 47,
-- 135, 48, 80, 49, 47, 50, 48, 99, 61, 43,
-- 50, 110, 41, 67, 67, 67, 60, 63, 63, 63,
-- 57, 155, 68, 69, 63, 37, 44, 66, 67, 67,
-- 67, 63, 63, 63, 63, 73, 59, 68, 69, 70,
-- 34, 34, 34, 43, 75, 38, 154, 92, 83, 83,
-- 83, 64, 44, 120, 64, 64, 64, 67, 67, 67,
--
-- 44, 57, 99, 68, 69, 107, 68, 69, 120, 127,
-- 108, 153, 152, 121, 83, 83, 83, 133, 133, 133,
-- 146, 133, 133, 133, 146, 140, 140, 140, 121, 141,
-- 140, 140, 140, 151, 141, 158, 150, 149, 148, 144,
-- 147, 143, 142, 139, 147, 36, 36, 36, 36, 36,
-- 36, 36, 36, 40, 138, 137, 136, 40, 40, 42,
-- 42, 42, 42, 42, 42, 42, 42, 56, 56, 56,
-- 56, 62, 132, 62, 64, 131, 130, 64, 129, 64,
-- 64, 65, 128, 158, 65, 65, 65, 65, 71, 127,
-- 71, 71, 74, 74, 74, 74, 74, 74, 74, 74,
--
-- 76, 76, 76, 76, 76, 76, 76, 76, 89, 126,
-- 89, 90, 125, 90, 90, 124, 90, 90, 119, 119,
-- 119, 119, 119, 119, 119, 119, 145, 145, 145, 145,
-- 145, 145, 145, 145, 123, 122, 59, 59, 118, 117,
-- 116, 115, 114, 113, 45, 112, 108, 111, 109, 106,
-- 105, 104, 46, 103, 91, 87, 102, 101, 100, 98,
-- 97, 96, 95, 94, 93, 77, 75, 91, 88, 87,
-- 86, 57, 85, 84, 57, 82, 81, 78, 77, 75,
-- 72, 158, 58, 57, 53, 35, 158, 31, 23, 23,
-- 9, 158, 158, 158, 158, 158, 158, 158, 158, 158,
--
-- 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-- 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-- 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-- 158, 158, 158, 158, 158, 158, 158
-+ 21, 21, 21, 21, 10, 22, 10, 24, 25, 25,
-+ 25, 32, 33, 33, 164, 26, 34, 34, 34, 52,
-+ 53, 27, 26, 26, 26, 26, 10, 11, 12, 11,
-+ 13, 14, 28, 15, 16, 28, 28, 28, 24, 28,
-+ 28, 28, 10, 18, 19, 20, 29, 29, 29, 29,
-+ 29, 30, 10, 29, 29, 29, 29, 29, 29, 29,
-+
-+ 29, 29, 29, 29, 29, 29, 29, 29, 29, 29,
-+ 10, 22, 10, 23, 34, 34, 34, 37, 39, 43,
-+ 32, 33, 33, 45, 55, 56, 46, 60, 43, 45,
-+ 65, 163, 46, 65, 65, 65, 44, 38, 60, 74,
-+ 58, 47, 141, 48, 142, 44, 49, 47, 50, 48,
-+ 76, 51, 62, 94, 50, 41, 44, 51, 37, 61,
-+ 64, 64, 64, 58, 34, 34, 34, 64, 162, 80,
-+ 67, 68, 68, 68, 64, 64, 64, 64, 38, 81,
-+ 69, 70, 71, 68, 68, 68, 60, 161, 43, 69,
-+ 70, 65, 69, 70, 65, 65, 65, 125, 85, 85,
-+
-+ 85, 58, 68, 68, 68, 44, 102, 110, 125, 133,
-+ 102, 69, 70, 111, 114, 160, 159, 126, 85, 85,
-+ 85, 140, 140, 140, 140, 140, 140, 153, 126, 147,
-+ 147, 147, 153, 148, 147, 147, 147, 158, 148, 165,
-+ 157, 156, 155, 151, 150, 149, 146, 154, 145, 144,
-+ 143, 139, 154, 36, 36, 36, 36, 36, 36, 36,
-+ 36, 40, 138, 137, 136, 40, 40, 42, 42, 42,
-+ 42, 42, 42, 42, 42, 57, 57, 57, 57, 63,
-+ 135, 63, 65, 134, 165, 65, 133, 65, 65, 66,
-+ 132, 131, 66, 66, 66, 66, 72, 130, 72, 72,
-+
-+ 75, 75, 75, 75, 75, 75, 75, 75, 77, 77,
-+ 77, 77, 77, 77, 77, 77, 91, 129, 91, 92,
-+ 128, 92, 92, 127, 92, 92, 124, 124, 124, 124,
-+ 124, 124, 124, 124, 152, 152, 152, 152, 152, 152,
-+ 152, 152, 60, 60, 123, 122, 121, 120, 119, 118,
-+ 117, 45, 116, 111, 115, 113, 112, 109, 108, 107,
-+ 46, 106, 93, 89, 105, 104, 103, 101, 100, 99,
-+ 98, 97, 96, 95, 78, 76, 93, 90, 89, 88,
-+ 58, 87, 86, 58, 84, 83, 82, 79, 78, 76,
-+ 73, 165, 59, 58, 54, 35, 165, 31, 23, 23,
-+
-+ 9, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 165, 165
- } ;
-
--static yyconst flex_int16_t yy_chk[438] =
-+static yyconst flex_int16_t yy_chk[449] =
- { 0,
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
-- 1, 1, 1, 1, 1, 1, 3, 3, 3, 3,
-- 7, 7, 7, 156, 3, 11, 11, 11, 18, 18,
-- 3, 3, 3, 3, 3, 5, 5, 5, 5, 5,
-+ 1, 1, 1, 1, 1, 1, 1, 3, 3, 3,
-+ 3, 7, 7, 7, 163, 3, 11, 11, 11, 18,
-+ 18, 3, 3, 3, 3, 3, 5, 5, 5, 5,
- 5, 5, 5, 5, 5, 5, 5, 5, 5, 5,
- 5, 5, 5, 5, 5, 5, 5, 5, 5, 5,
- 5, 5, 5, 5, 5, 5, 5, 5, 5, 5,
-
- 5, 5, 5, 5, 5, 5, 5, 5, 5, 5,
-- 5, 8, 12, 12, 12, 14, 15, 16, 8, 8,
-- 8, 17, 20, 20, 17, 23, 24, 29, 155, 24,
-- 29, 29, 29, 48, 16, 14, 31, 29, 128, 17,
-- 128, 17, 48, 17, 24, 17, 24, 99, 24, 42,
-- 24, 99, 15, 33, 33, 33, 23, 26, 26, 26,
-- 26, 154, 33, 33, 26, 36, 42, 31, 32, 32,
-- 32, 26, 26, 26, 26, 44, 59, 32, 32, 32,
-- 34, 34, 34, 73, 75, 36, 153, 75, 59, 59,
-- 59, 65, 44, 110, 65, 65, 65, 67, 67, 67,
--
-- 73, 65, 83, 89, 89, 97, 67, 67, 119, 127,
-- 97, 150, 149, 110, 83, 83, 83, 133, 133, 133,
-- 141, 127, 127, 127, 145, 136, 136, 136, 119, 136,
-- 140, 140, 140, 148, 140, 147, 144, 143, 142, 139,
-- 141, 138, 137, 135, 145, 159, 159, 159, 159, 159,
-- 159, 159, 159, 160, 134, 132, 131, 160, 160, 161,
-- 161, 161, 161, 161, 161, 161, 161, 162, 162, 162,
-- 162, 163, 126, 163, 164, 125, 124, 164, 123, 164,
-- 164, 165, 122, 121, 165, 165, 165, 165, 166, 120,
-- 166, 166, 167, 167, 167, 167, 167, 167, 167, 167,
--
-- 168, 168, 168, 168, 168, 168, 168, 168, 169, 118,
-- 169, 170, 117, 170, 170, 116, 170, 170, 171, 171,
-- 171, 171, 171, 171, 171, 171, 172, 172, 172, 172,
-- 172, 172, 172, 172, 115, 114, 112, 111, 109, 108,
-- 107, 106, 105, 104, 103, 102, 101, 100, 98, 96,
-- 95, 94, 93, 92, 90, 88, 86, 85, 84, 82,
-- 81, 80, 79, 78, 77, 76, 74, 72, 69, 68,
-- 66, 63, 61, 60, 56, 50, 49, 47, 46, 45,
-+ 5, 5, 5, 8, 12, 12, 12, 14, 15, 16,
-+ 8, 8, 8, 17, 20, 20, 17, 23, 42, 24,
-+ 29, 162, 24, 29, 29, 29, 16, 14, 31, 44,
-+ 29, 17, 134, 17, 134, 42, 17, 24, 17, 24,
-+ 76, 17, 24, 76, 24, 15, 44, 24, 36, 23,
-+ 26, 26, 26, 26, 34, 34, 34, 26, 161, 48,
-+ 31, 32, 32, 32, 26, 26, 26, 26, 36, 48,
-+ 32, 32, 32, 33, 33, 33, 60, 160, 74, 91,
-+ 91, 66, 33, 33, 66, 66, 66, 114, 60, 60,
-+
-+ 60, 66, 68, 68, 68, 74, 85, 99, 124, 133,
-+ 102, 68, 68, 99, 102, 157, 156, 114, 85, 85,
-+ 85, 133, 133, 133, 140, 140, 140, 148, 124, 143,
-+ 143, 143, 152, 143, 147, 147, 147, 155, 147, 154,
-+ 151, 150, 149, 146, 145, 144, 142, 148, 141, 138,
-+ 137, 132, 152, 166, 166, 166, 166, 166, 166, 166,
-+ 166, 167, 131, 130, 129, 167, 167, 168, 168, 168,
-+ 168, 168, 168, 168, 168, 169, 169, 169, 169, 170,
-+ 128, 170, 171, 127, 126, 171, 125, 171, 171, 172,
-+ 123, 122, 172, 172, 172, 172, 173, 121, 173, 173,
-+
-+ 174, 174, 174, 174, 174, 174, 174, 174, 175, 175,
-+ 175, 175, 175, 175, 175, 175, 176, 120, 176, 177,
-+ 119, 177, 177, 118, 177, 177, 178, 178, 178, 178,
-+ 178, 178, 178, 178, 179, 179, 179, 179, 179, 179,
-+ 179, 179, 116, 115, 113, 112, 111, 110, 109, 108,
-+ 107, 106, 105, 104, 103, 101, 100, 98, 97, 96,
-+ 95, 94, 92, 90, 88, 87, 86, 84, 83, 82,
-+ 81, 80, 79, 78, 77, 75, 73, 70, 69, 67,
-+ 64, 62, 61, 57, 51, 50, 49, 47, 46, 45,
- 41, 38, 22, 21, 19, 13, 9, 6, 4, 2,
-- 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-
-- 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-- 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-- 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-- 158, 158, 158, 158, 158, 158, 158
-+ 165, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 165, 165
- } ;
-
- static yy_state_type yy_last_accepting_state;
-@@ -662,7 +664,7 @@ static int dts_version = 1;
- static void push_input_file(const char *filename);
- static bool pop_input_file(void);
- static void lexical_error(const char *fmt, ...);
--#line 666 "dtc-lexer.lex.c"
-+#line 668 "dtc-lexer.lex.c"
-
- #define INITIAL 0
- #define BYTESTRING 1
-@@ -704,7 +706,7 @@ FILE *yyget_out (void );
-
- void yyset_out (FILE * out_str );
-
--yy_size_t yyget_leng (void );
-+int yyget_leng (void );
-
- char *yyget_text (void );
-
-@@ -853,6 +855,10 @@ YY_DECL
- register char *yy_cp, *yy_bp;
- register int yy_act;
-
-+#line 68 "dtc-lexer.l"
-+
-+#line 861 "dtc-lexer.lex.c"
-+
- if ( !(yy_init) )
- {
- (yy_init) = 1;
-@@ -879,11 +885,6 @@ YY_DECL
- yy_load_buffer_state( );
- }
-
-- {
--#line 68 "dtc-lexer.l"
--
--#line 886 "dtc-lexer.lex.c"
--
- while ( 1 ) /* loops until end-of-file is reached */
- {
- yy_cp = (yy_c_buf_p);
-@@ -901,7 +902,7 @@ YY_DECL
- yy_match:
- do
- {
-- register YY_CHAR yy_c = yy_ec[YY_SC_TO_UI(*yy_cp)] ;
-+ register YY_CHAR yy_c = yy_ec[YY_SC_TO_UI(*yy_cp)];
- if ( yy_accept[yy_current_state] )
- {
- (yy_last_accepting_state) = yy_current_state;
-@@ -910,13 +911,13 @@ yy_match:
- while ( yy_chk[yy_base[yy_current_state] + yy_c] != yy_current_state )
- {
- yy_current_state = (int) yy_def[yy_current_state];
-- if ( yy_current_state >= 159 )
-+ if ( yy_current_state >= 166 )
- yy_c = yy_meta[(unsigned int) yy_c];
- }
- yy_current_state = yy_nxt[yy_base[yy_current_state] + (unsigned int) yy_c];
- ++yy_cp;
- }
-- while ( yy_current_state != 158 );
-+ while ( yy_current_state != 165 );
- yy_cp = (yy_last_accepting_cpos);
- yy_current_state = (yy_last_accepting_state);
-
-@@ -1007,23 +1008,31 @@ case 5:
- YY_RULE_SETUP
- #line 116 "dtc-lexer.l"
- {
-+ DPRINT("Keyword: /plugin/\n");
-+ return DT_PLUGIN;
-+ }
-+ YY_BREAK
-+case 6:
-+YY_RULE_SETUP
-+#line 121 "dtc-lexer.l"
-+{
- DPRINT("Keyword: /memreserve/\n");
- BEGIN_DEFAULT();
- return DT_MEMRESERVE;
- }
- YY_BREAK
--case 6:
-+case 7:
- YY_RULE_SETUP
--#line 122 "dtc-lexer.l"
-+#line 127 "dtc-lexer.l"
- {
- DPRINT("Keyword: /bits/\n");
- BEGIN_DEFAULT();
- return DT_BITS;
- }
- YY_BREAK
--case 7:
-+case 8:
- YY_RULE_SETUP
--#line 128 "dtc-lexer.l"
-+#line 133 "dtc-lexer.l"
- {
- DPRINT("Keyword: /delete-property/\n");
- DPRINT("<PROPNODENAME>\n");
-@@ -1031,9 +1040,9 @@ YY_RULE_SETUP
- return DT_DEL_PROP;
- }
- YY_BREAK
--case 8:
-+case 9:
- YY_RULE_SETUP
--#line 135 "dtc-lexer.l"
-+#line 140 "dtc-lexer.l"
- {
- DPRINT("Keyword: /delete-node/\n");
- DPRINT("<PROPNODENAME>\n");
-@@ -1041,9 +1050,9 @@ YY_RULE_SETUP
- return DT_DEL_NODE;
- }
- YY_BREAK
--case 9:
-+case 10:
- YY_RULE_SETUP
--#line 142 "dtc-lexer.l"
-+#line 147 "dtc-lexer.l"
- {
- DPRINT("Label: %s\n", yytext);
- yylval.labelref = xstrdup(yytext);
-@@ -1051,9 +1060,9 @@ YY_RULE_SETUP
- return DT_LABEL;
- }
- YY_BREAK
--case 10:
-+case 11:
- YY_RULE_SETUP
--#line 149 "dtc-lexer.l"
-+#line 154 "dtc-lexer.l"
- {
- char *e;
- DPRINT("Integer Literal: '%s'\n", yytext);
-@@ -1073,10 +1082,10 @@ YY_RULE_SETUP
- return DT_LITERAL;
- }
- YY_BREAK
--case 11:
--/* rule 11 can match eol */
-+case 12:
-+/* rule 12 can match eol */
- YY_RULE_SETUP
--#line 168 "dtc-lexer.l"
-+#line 173 "dtc-lexer.l"
- {
- struct data d;
- DPRINT("Character literal: %s\n", yytext);
-@@ -1098,18 +1107,18 @@ YY_RULE_SETUP
- return DT_CHAR_LITERAL;
- }
- YY_BREAK
--case 12:
-+case 13:
- YY_RULE_SETUP
--#line 189 "dtc-lexer.l"
-+#line 194 "dtc-lexer.l"
- { /* label reference */
- DPRINT("Ref: %s\n", yytext+1);
- yylval.labelref = xstrdup(yytext+1);
- return DT_REF;
- }
- YY_BREAK
--case 13:
-+case 14:
- YY_RULE_SETUP
--#line 195 "dtc-lexer.l"
-+#line 200 "dtc-lexer.l"
- { /* new-style path reference */
- yytext[yyleng-1] = '\0';
- DPRINT("Ref: %s\n", yytext+2);
-@@ -1117,27 +1126,27 @@ YY_RULE_SETUP
- return DT_REF;
- }
- YY_BREAK
--case 14:
-+case 15:
- YY_RULE_SETUP
--#line 202 "dtc-lexer.l"
-+#line 207 "dtc-lexer.l"
- {
- yylval.byte = strtol(yytext, NULL, 16);
- DPRINT("Byte: %02x\n", (int)yylval.byte);
- return DT_BYTE;
- }
- YY_BREAK
--case 15:
-+case 16:
- YY_RULE_SETUP
--#line 208 "dtc-lexer.l"
-+#line 213 "dtc-lexer.l"
- {
- DPRINT("/BYTESTRING\n");
- BEGIN_DEFAULT();
- return ']';
- }
- YY_BREAK
--case 16:
-+case 17:
- YY_RULE_SETUP
--#line 214 "dtc-lexer.l"
-+#line 219 "dtc-lexer.l"
- {
- DPRINT("PropNodeName: %s\n", yytext);
- yylval.propnodename = xstrdup((yytext[0] == '\\') ?
-@@ -1146,75 +1155,75 @@ YY_RULE_SETUP
- return DT_PROPNODENAME;
- }
- YY_BREAK
--case 17:
-+case 18:
- YY_RULE_SETUP
--#line 222 "dtc-lexer.l"
-+#line 227 "dtc-lexer.l"
- {
- DPRINT("Binary Include\n");
- return DT_INCBIN;
- }
- YY_BREAK
--case 18:
--/* rule 18 can match eol */
--YY_RULE_SETUP
--#line 227 "dtc-lexer.l"
--/* eat whitespace */
-- YY_BREAK
- case 19:
- /* rule 19 can match eol */
- YY_RULE_SETUP
--#line 228 "dtc-lexer.l"
--/* eat C-style comments */
-+#line 232 "dtc-lexer.l"
-+/* eat whitespace */
- YY_BREAK
- case 20:
- /* rule 20 can match eol */
- YY_RULE_SETUP
--#line 229 "dtc-lexer.l"
--/* eat C++-style comments */
-+#line 233 "dtc-lexer.l"
-+/* eat C-style comments */
- YY_BREAK
- case 21:
-+/* rule 21 can match eol */
- YY_RULE_SETUP
--#line 231 "dtc-lexer.l"
--{ return DT_LSHIFT; };
-+#line 234 "dtc-lexer.l"
-+/* eat C++-style comments */
- YY_BREAK
- case 22:
- YY_RULE_SETUP
--#line 232 "dtc-lexer.l"
--{ return DT_RSHIFT; };
-+#line 236 "dtc-lexer.l"
-+{ return DT_LSHIFT; };
- YY_BREAK
- case 23:
- YY_RULE_SETUP
--#line 233 "dtc-lexer.l"
--{ return DT_LE; };
-+#line 237 "dtc-lexer.l"
-+{ return DT_RSHIFT; };
- YY_BREAK
- case 24:
- YY_RULE_SETUP
--#line 234 "dtc-lexer.l"
--{ return DT_GE; };
-+#line 238 "dtc-lexer.l"
-+{ return DT_LE; };
- YY_BREAK
- case 25:
- YY_RULE_SETUP
--#line 235 "dtc-lexer.l"
--{ return DT_EQ; };
-+#line 239 "dtc-lexer.l"
-+{ return DT_GE; };
- YY_BREAK
- case 26:
- YY_RULE_SETUP
--#line 236 "dtc-lexer.l"
--{ return DT_NE; };
-+#line 240 "dtc-lexer.l"
-+{ return DT_EQ; };
- YY_BREAK
- case 27:
- YY_RULE_SETUP
--#line 237 "dtc-lexer.l"
--{ return DT_AND; };
-+#line 241 "dtc-lexer.l"
-+{ return DT_NE; };
- YY_BREAK
- case 28:
- YY_RULE_SETUP
--#line 238 "dtc-lexer.l"
--{ return DT_OR; };
-+#line 242 "dtc-lexer.l"
-+{ return DT_AND; };
- YY_BREAK
- case 29:
- YY_RULE_SETUP
--#line 240 "dtc-lexer.l"
-+#line 243 "dtc-lexer.l"
-+{ return DT_OR; };
-+ YY_BREAK
-+case 30:
-+YY_RULE_SETUP
-+#line 245 "dtc-lexer.l"
- {
- DPRINT("Char: %c (\\x%02x)\n", yytext[0],
- (unsigned)yytext[0]);
-@@ -1230,12 +1239,12 @@ YY_RULE_SETUP
- return yytext[0];
- }
- YY_BREAK
--case 30:
-+case 31:
- YY_RULE_SETUP
--#line 255 "dtc-lexer.l"
-+#line 260 "dtc-lexer.l"
- ECHO;
- YY_BREAK
--#line 1239 "dtc-lexer.lex.c"
-+#line 1248 "dtc-lexer.lex.c"
-
- case YY_END_OF_BUFFER:
- {
-@@ -1365,7 +1374,6 @@ ECHO;
- "fatal flex scanner internal error--no action found" );
- } /* end of action switch */
- } /* end of scanning one token */
-- } /* end of user's declarations */
- } /* end of yylex */
-
- /* yy_get_next_buffer - try to read in a new buffer
-@@ -1421,21 +1429,21 @@ static int yy_get_next_buffer (void)
-
- else
- {
-- yy_size_t num_to_read =
-+ int num_to_read =
- YY_CURRENT_BUFFER_LVALUE->yy_buf_size - number_to_move - 1;
-
- while ( num_to_read <= 0 )
- { /* Not enough room in the buffer - grow it. */
-
- /* just a shorter name for the current buffer */
-- YY_BUFFER_STATE b = YY_CURRENT_BUFFER_LVALUE;
-+ YY_BUFFER_STATE b = YY_CURRENT_BUFFER;
-
- int yy_c_buf_p_offset =
- (int) ((yy_c_buf_p) - b->yy_ch_buf);
-
- if ( b->yy_is_our_buffer )
- {
-- yy_size_t new_size = b->yy_buf_size * 2;
-+ int new_size = b->yy_buf_size * 2;
-
- if ( new_size <= 0 )
- b->yy_buf_size += b->yy_buf_size / 8;
-@@ -1466,7 +1474,7 @@ static int yy_get_next_buffer (void)
-
- /* Read in more data. */
- YY_INPUT( (&YY_CURRENT_BUFFER_LVALUE->yy_ch_buf[number_to_move]),
-- (yy_n_chars), num_to_read );
-+ (yy_n_chars), (size_t) num_to_read );
-
- YY_CURRENT_BUFFER_LVALUE->yy_n_chars = (yy_n_chars);
- }
-@@ -1528,7 +1536,7 @@ static int yy_get_next_buffer (void)
- while ( yy_chk[yy_base[yy_current_state] + yy_c] != yy_current_state )
- {
- yy_current_state = (int) yy_def[yy_current_state];
-- if ( yy_current_state >= 159 )
-+ if ( yy_current_state >= 166 )
- yy_c = yy_meta[(unsigned int) yy_c];
- }
- yy_current_state = yy_nxt[yy_base[yy_current_state] + (unsigned int) yy_c];
-@@ -1556,13 +1564,13 @@ static int yy_get_next_buffer (void)
- while ( yy_chk[yy_base[yy_current_state] + yy_c] != yy_current_state )
- {
- yy_current_state = (int) yy_def[yy_current_state];
-- if ( yy_current_state >= 159 )
-+ if ( yy_current_state >= 166 )
- yy_c = yy_meta[(unsigned int) yy_c];
- }
- yy_current_state = yy_nxt[yy_base[yy_current_state] + (unsigned int) yy_c];
-- yy_is_jam = (yy_current_state == 158);
-+ yy_is_jam = (yy_current_state == 165);
-
-- return yy_is_jam ? 0 : yy_current_state;
-+ return yy_is_jam ? 0 : yy_current_state;
- }
-
- #ifndef YY_NO_INPUT
-@@ -1589,7 +1597,7 @@ static int yy_get_next_buffer (void)
-
- else
- { /* need more input */
-- yy_size_t offset = (yy_c_buf_p) - (yytext_ptr);
-+ int offset = (yy_c_buf_p) - (yytext_ptr);
- ++(yy_c_buf_p);
-
- switch ( yy_get_next_buffer( ) )
-@@ -1863,7 +1871,7 @@ void yypop_buffer_state (void)
- */
- static void yyensure_buffer_stack (void)
- {
-- yy_size_t num_to_alloc;
-+ int num_to_alloc;
-
- if (!(yy_buffer_stack)) {
-
-@@ -1960,12 +1968,12 @@ YY_BUFFER_STATE yy_scan_string (yyconst
- *
- * @return the newly allocated buffer state object.
- */
--YY_BUFFER_STATE yy_scan_bytes (yyconst char * yybytes, yy_size_t _yybytes_len )
-+YY_BUFFER_STATE yy_scan_bytes (yyconst char * yybytes, int _yybytes_len )
- {
- YY_BUFFER_STATE b;
- char *buf;
- yy_size_t n;
-- yy_size_t i;
-+ int i;
-
- /* Get memory for full buffer, including space for trailing EOB's. */
- n = _yybytes_len + 2;
-@@ -2047,7 +2055,7 @@ FILE *yyget_out (void)
- /** Get the length of the current token.
- *
- */
--yy_size_t yyget_leng (void)
-+int yyget_leng (void)
- {
- return yyleng;
- }
-@@ -2195,7 +2203,7 @@ void yyfree (void * ptr )
-
- #define YYTABLES_NAME "yytables"
-
--#line 254 "dtc-lexer.l"
-+#line 260 "dtc-lexer.l"
-
-
-
---- a/scripts/dtc/dtc-parser.tab.c_shipped
-+++ b/scripts/dtc/dtc-parser.tab.c_shipped
-@@ -1,19 +1,19 @@
--/* A Bison parser, made by GNU Bison 3.0.2. */
-+/* A Bison parser, made by GNU Bison 2.5. */
-
- /* Bison implementation for Yacc-like parsers in C
--
-- Copyright (C) 1984, 1989-1990, 2000-2013 Free Software Foundation, Inc.
--
-+
-+ Copyright (C) 1984, 1989-1990, 2000-2011 Free Software Foundation, Inc.
-+
- This program is free software: you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation, either version 3 of the License, or
- (at your option) any later version.
--
-+
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
--
-+
- You should have received a copy of the GNU General Public License
- along with this program. If not, see <http://www.gnu.org/licenses/>. */
-
-@@ -26,7 +26,7 @@
- special exception, which will cause the skeleton and the resulting
- Bison output files to be licensed under the GNU General Public
- License without this special exception.
--
-+
- This special exception was added by the Free Software Foundation in
- version 2.2 of Bison. */
-
-@@ -44,7 +44,7 @@
- #define YYBISON 1
-
- /* Bison version. */
--#define YYBISON_VERSION "3.0.2"
-+#define YYBISON_VERSION "2.5"
-
- /* Skeleton name. */
- #define YYSKELETON_NAME "yacc.c"
-@@ -58,13 +58,18 @@
- /* Pull parsers. */
- #define YYPULL 1
-
-+/* Using locations. */
-+#define YYLSP_NEEDED 1
-
-
-
- /* Copy the first part of user declarations. */
--#line 20 "dtc-parser.y" /* yacc.c:339 */
-+
-+/* Line 268 of yacc.c */
-+#line 20 "dtc-parser.y"
-
- #include <stdio.h>
-+#include <inttypes.h>
-
- #include "dtc.h"
- #include "srcpos.h"
-@@ -80,15 +85,14 @@ extern void yyerror(char const *s);
- extern struct boot_info *the_boot_info;
- extern bool treesource_error;
-
--#line 84 "dtc-parser.tab.c" /* yacc.c:339 */
-
--# ifndef YY_NULLPTR
--# if defined __cplusplus && 201103L <= __cplusplus
--# define YY_NULLPTR nullptr
--# else
--# define YY_NULLPTR 0
--# endif
--# endif
-+/* Line 268 of yacc.c */
-+#line 91 "dtc-parser.tab.c"
-+
-+/* Enabling traces. */
-+#ifndef YYDEBUG
-+# define YYDEBUG 0
-+#endif
-
- /* Enabling verbose error messages. */
- #ifdef YYERROR_VERBOSE
-@@ -98,53 +102,51 @@ extern bool treesource_error;
- # define YYERROR_VERBOSE 0
- #endif
-
--/* In a future release of Bison, this section will be replaced
-- by #include "dtc-parser.tab.h". */
--#ifndef YY_YY_DTC_PARSER_TAB_H_INCLUDED
--# define YY_YY_DTC_PARSER_TAB_H_INCLUDED
--/* Debug traces. */
--#ifndef YYDEBUG
--# define YYDEBUG 0
--#endif
--#if YYDEBUG
--extern int yydebug;
-+/* Enabling the token table. */
-+#ifndef YYTOKEN_TABLE
-+# define YYTOKEN_TABLE 0
- #endif
-
--/* Token type. */
-+
-+/* Tokens. */
- #ifndef YYTOKENTYPE
- # define YYTOKENTYPE
-- enum yytokentype
-- {
-- DT_V1 = 258,
-- DT_MEMRESERVE = 259,
-- DT_LSHIFT = 260,
-- DT_RSHIFT = 261,
-- DT_LE = 262,
-- DT_GE = 263,
-- DT_EQ = 264,
-- DT_NE = 265,
-- DT_AND = 266,
-- DT_OR = 267,
-- DT_BITS = 268,
-- DT_DEL_PROP = 269,
-- DT_DEL_NODE = 270,
-- DT_PROPNODENAME = 271,
-- DT_LITERAL = 272,
-- DT_CHAR_LITERAL = 273,
-- DT_BYTE = 274,
-- DT_STRING = 275,
-- DT_LABEL = 276,
-- DT_REF = 277,
-- DT_INCBIN = 278
-- };
-+ /* Put the tokens into the symbol table, so that GDB and other debuggers
-+ know about them. */
-+ enum yytokentype {
-+ DT_V1 = 258,
-+ DT_PLUGIN = 259,
-+ DT_MEMRESERVE = 260,
-+ DT_LSHIFT = 261,
-+ DT_RSHIFT = 262,
-+ DT_LE = 263,
-+ DT_GE = 264,
-+ DT_EQ = 265,
-+ DT_NE = 266,
-+ DT_AND = 267,
-+ DT_OR = 268,
-+ DT_BITS = 269,
-+ DT_DEL_PROP = 270,
-+ DT_DEL_NODE = 271,
-+ DT_PROPNODENAME = 272,
-+ DT_LITERAL = 273,
-+ DT_CHAR_LITERAL = 274,
-+ DT_BYTE = 275,
-+ DT_STRING = 276,
-+ DT_LABEL = 277,
-+ DT_REF = 278,
-+ DT_INCBIN = 279
-+ };
- #endif
-
--/* Value type. */
-+
-+
- #if ! defined YYSTYPE && ! defined YYSTYPE_IS_DECLARED
--typedef union YYSTYPE YYSTYPE;
--union YYSTYPE
-+typedef union YYSTYPE
- {
--#line 38 "dtc-parser.y" /* yacc.c:355 */
-+
-+/* Line 293 of yacc.c */
-+#line 39 "dtc-parser.y"
-
- char *propnodename;
- char *labelref;
-@@ -162,37 +164,37 @@ union YYSTYPE
- struct node *nodelist;
- struct reserve_info *re;
- uint64_t integer;
-+ int is_plugin;
-
--#line 167 "dtc-parser.tab.c" /* yacc.c:355 */
--};
-+
-+
-+/* Line 293 of yacc.c */
-+#line 173 "dtc-parser.tab.c"
-+} YYSTYPE;
- # define YYSTYPE_IS_TRIVIAL 1
-+# define yystype YYSTYPE /* obsolescent; will be withdrawn */
- # define YYSTYPE_IS_DECLARED 1
- #endif
-
--/* Location type. */
- #if ! defined YYLTYPE && ! defined YYLTYPE_IS_DECLARED
--typedef struct YYLTYPE YYLTYPE;
--struct YYLTYPE
-+typedef struct YYLTYPE
- {
- int first_line;
- int first_column;
- int last_line;
- int last_column;
--};
-+} YYLTYPE;
-+# define yyltype YYLTYPE /* obsolescent; will be withdrawn */
- # define YYLTYPE_IS_DECLARED 1
- # define YYLTYPE_IS_TRIVIAL 1
- #endif
-
-
--extern YYSTYPE yylval;
--extern YYLTYPE yylloc;
--int yyparse (void);
--
--#endif /* !YY_YY_DTC_PARSER_TAB_H_INCLUDED */
--
- /* Copy the second part of user declarations. */
-
--#line 196 "dtc-parser.tab.c" /* yacc.c:358 */
-+
-+/* Line 343 of yacc.c */
-+#line 198 "dtc-parser.tab.c"
-
- #ifdef short
- # undef short
-@@ -206,8 +208,11 @@ typedef unsigned char yytype_uint8;
-
- #ifdef YYTYPE_INT8
- typedef YYTYPE_INT8 yytype_int8;
--#else
-+#elif (defined __STDC__ || defined __C99__FUNC__ \
-+ || defined __cplusplus || defined _MSC_VER)
- typedef signed char yytype_int8;
-+#else
-+typedef short int yytype_int8;
- #endif
-
- #ifdef YYTYPE_UINT16
-@@ -227,7 +232,8 @@ typedef short int yytype_int16;
- # define YYSIZE_T __SIZE_TYPE__
- # elif defined size_t
- # define YYSIZE_T size_t
--# elif ! defined YYSIZE_T
-+# elif ! defined YYSIZE_T && (defined __STDC__ || defined __C99__FUNC__ \
-+ || defined __cplusplus || defined _MSC_VER)
- # include <stddef.h> /* INFRINGES ON USER NAME SPACE */
- # define YYSIZE_T size_t
- # else
-@@ -241,68 +247,39 @@ typedef short int yytype_int16;
- # if defined YYENABLE_NLS && YYENABLE_NLS
- # if ENABLE_NLS
- # include <libintl.h> /* INFRINGES ON USER NAME SPACE */
--# define YY_(Msgid) dgettext ("bison-runtime", Msgid)
-+# define YY_(msgid) dgettext ("bison-runtime", msgid)
- # endif
- # endif
- # ifndef YY_
--# define YY_(Msgid) Msgid
--# endif
--#endif
--
--#ifndef YY_ATTRIBUTE
--# if (defined __GNUC__ \
-- && (2 < __GNUC__ || (__GNUC__ == 2 && 96 <= __GNUC_MINOR__))) \
-- || defined __SUNPRO_C && 0x5110 <= __SUNPRO_C
--# define YY_ATTRIBUTE(Spec) __attribute__(Spec)
--# else
--# define YY_ATTRIBUTE(Spec) /* empty */
--# endif
--#endif
--
--#ifndef YY_ATTRIBUTE_PURE
--# define YY_ATTRIBUTE_PURE YY_ATTRIBUTE ((__pure__))
--#endif
--
--#ifndef YY_ATTRIBUTE_UNUSED
--# define YY_ATTRIBUTE_UNUSED YY_ATTRIBUTE ((__unused__))
--#endif
--
--#if !defined _Noreturn \
-- && (!defined __STDC_VERSION__ || __STDC_VERSION__ < 201112)
--# if defined _MSC_VER && 1200 <= _MSC_VER
--# define _Noreturn __declspec (noreturn)
--# else
--# define _Noreturn YY_ATTRIBUTE ((__noreturn__))
-+# define YY_(msgid) msgid
- # endif
- #endif
-
- /* Suppress unused-variable warnings by "using" E. */
- #if ! defined lint || defined __GNUC__
--# define YYUSE(E) ((void) (E))
-+# define YYUSE(e) ((void) (e))
- #else
--# define YYUSE(E) /* empty */
-+# define YYUSE(e) /* empty */
- #endif
-
--#if defined __GNUC__ && 407 <= __GNUC__ * 100 + __GNUC_MINOR__
--/* Suppress an incorrect diagnostic about yylval being uninitialized. */
--# define YY_IGNORE_MAYBE_UNINITIALIZED_BEGIN \
-- _Pragma ("GCC diagnostic push") \
-- _Pragma ("GCC diagnostic ignored \"-Wuninitialized\"")\
-- _Pragma ("GCC diagnostic ignored \"-Wmaybe-uninitialized\"")
--# define YY_IGNORE_MAYBE_UNINITIALIZED_END \
-- _Pragma ("GCC diagnostic pop")
-+/* Identity function, used to suppress warnings about constant conditions. */
-+#ifndef lint
-+# define YYID(n) (n)
- #else
--# define YY_INITIAL_VALUE(Value) Value
--#endif
--#ifndef YY_IGNORE_MAYBE_UNINITIALIZED_BEGIN
--# define YY_IGNORE_MAYBE_UNINITIALIZED_BEGIN
--# define YY_IGNORE_MAYBE_UNINITIALIZED_END
-+#if (defined __STDC__ || defined __C99__FUNC__ \
-+ || defined __cplusplus || defined _MSC_VER)
-+static int
-+YYID (int yyi)
-+#else
-+static int
-+YYID (yyi)
-+ int yyi;
- #endif
--#ifndef YY_INITIAL_VALUE
--# define YY_INITIAL_VALUE(Value) /* Nothing. */
-+{
-+ return yyi;
-+}
- #endif
-
--
- #if ! defined yyoverflow || YYERROR_VERBOSE
-
- /* The parser invokes alloca or malloc; define the necessary symbols. */
-@@ -320,9 +297,9 @@ typedef short int yytype_int16;
- # define alloca _alloca
- # else
- # define YYSTACK_ALLOC alloca
--# if ! defined _ALLOCA_H && ! defined EXIT_SUCCESS
-+# if ! defined _ALLOCA_H && ! defined EXIT_SUCCESS && (defined __STDC__ || defined __C99__FUNC__ \
-+ || defined __cplusplus || defined _MSC_VER)
- # include <stdlib.h> /* INFRINGES ON USER NAME SPACE */
-- /* Use EXIT_SUCCESS as a witness for stdlib.h. */
- # ifndef EXIT_SUCCESS
- # define EXIT_SUCCESS 0
- # endif
-@@ -332,8 +309,8 @@ typedef short int yytype_int16;
- # endif
-
- # ifdef YYSTACK_ALLOC
-- /* Pacify GCC's 'empty if-body' warning. */
--# define YYSTACK_FREE(Ptr) do { /* empty */; } while (0)
-+ /* Pacify GCC's `empty if-body' warning. */
-+# define YYSTACK_FREE(Ptr) do { /* empty */; } while (YYID (0))
- # ifndef YYSTACK_ALLOC_MAXIMUM
- /* The OS might guarantee only one guard page at the bottom of the stack,
- and a page size can be as small as 4096 bytes. So we cannot safely
-@@ -349,7 +326,7 @@ typedef short int yytype_int16;
- # endif
- # if (defined __cplusplus && ! defined EXIT_SUCCESS \
- && ! ((defined YYMALLOC || defined malloc) \
-- && (defined YYFREE || defined free)))
-+ && (defined YYFREE || defined free)))
- # include <stdlib.h> /* INFRINGES ON USER NAME SPACE */
- # ifndef EXIT_SUCCESS
- # define EXIT_SUCCESS 0
-@@ -357,13 +334,15 @@ typedef short int yytype_int16;
- # endif
- # ifndef YYMALLOC
- # define YYMALLOC malloc
--# if ! defined malloc && ! defined EXIT_SUCCESS
-+# if ! defined malloc && ! defined EXIT_SUCCESS && (defined __STDC__ || defined __C99__FUNC__ \
-+ || defined __cplusplus || defined _MSC_VER)
- void *malloc (YYSIZE_T); /* INFRINGES ON USER NAME SPACE */
- # endif
- # endif
- # ifndef YYFREE
- # define YYFREE free
--# if ! defined free && ! defined EXIT_SUCCESS
-+# if ! defined free && ! defined EXIT_SUCCESS && (defined __STDC__ || defined __C99__FUNC__ \
-+ || defined __cplusplus || defined _MSC_VER)
- void free (void *); /* INFRINGES ON USER NAME SPACE */
- # endif
- # endif
-@@ -373,8 +352,8 @@ void free (void *); /* INFRINGES ON USER
-
- #if (! defined yyoverflow \
- && (! defined __cplusplus \
-- || (defined YYLTYPE_IS_TRIVIAL && YYLTYPE_IS_TRIVIAL \
-- && defined YYSTYPE_IS_TRIVIAL && YYSTYPE_IS_TRIVIAL)))
-+ || (defined YYLTYPE_IS_TRIVIAL && YYLTYPE_IS_TRIVIAL \
-+ && defined YYSTYPE_IS_TRIVIAL && YYSTYPE_IS_TRIVIAL)))
-
- /* A type that is properly aligned for any stack member. */
- union yyalloc
-@@ -400,35 +379,35 @@ union yyalloc
- elements in the stack, and YYPTR gives the new location of the
- stack. Advance YYPTR to a properly aligned location for the next
- stack. */
--# define YYSTACK_RELOCATE(Stack_alloc, Stack) \
-- do \
-- { \
-- YYSIZE_T yynewbytes; \
-- YYCOPY (&yyptr->Stack_alloc, Stack, yysize); \
-- Stack = &yyptr->Stack_alloc; \
-- yynewbytes = yystacksize * sizeof (*Stack) + YYSTACK_GAP_MAXIMUM; \
-- yyptr += yynewbytes / sizeof (*yyptr); \
-- } \
-- while (0)
-+# define YYSTACK_RELOCATE(Stack_alloc, Stack) \
-+ do \
-+ { \
-+ YYSIZE_T yynewbytes; \
-+ YYCOPY (&yyptr->Stack_alloc, Stack, yysize); \
-+ Stack = &yyptr->Stack_alloc; \
-+ yynewbytes = yystacksize * sizeof (*Stack) + YYSTACK_GAP_MAXIMUM; \
-+ yyptr += yynewbytes / sizeof (*yyptr); \
-+ } \
-+ while (YYID (0))
-
- #endif
-
- #if defined YYCOPY_NEEDED && YYCOPY_NEEDED
--/* Copy COUNT objects from SRC to DST. The source and destination do
-+/* Copy COUNT objects from FROM to TO. The source and destination do
- not overlap. */
- # ifndef YYCOPY
- # if defined __GNUC__ && 1 < __GNUC__
--# define YYCOPY(Dst, Src, Count) \
-- __builtin_memcpy (Dst, Src, (Count) * sizeof (*(Src)))
-+# define YYCOPY(To, From, Count) \
-+ __builtin_memcpy (To, From, (Count) * sizeof (*(From)))
- # else
--# define YYCOPY(Dst, Src, Count) \
-- do \
-- { \
-- YYSIZE_T yyi; \
-- for (yyi = 0; yyi < (Count); yyi++) \
-- (Dst)[yyi] = (Src)[yyi]; \
-- } \
-- while (0)
-+# define YYCOPY(To, From, Count) \
-+ do \
-+ { \
-+ YYSIZE_T yyi; \
-+ for (yyi = 0; yyi < (Count); yyi++) \
-+ (To)[yyi] = (From)[yyi]; \
-+ } \
-+ while (YYID (0))
- # endif
- # endif
- #endif /* !YYCOPY_NEEDED */
-@@ -439,39 +418,37 @@ union yyalloc
- #define YYLAST 136
-
- /* YYNTOKENS -- Number of terminals. */
--#define YYNTOKENS 47
-+#define YYNTOKENS 48
- /* YYNNTS -- Number of nonterminals. */
--#define YYNNTS 28
-+#define YYNNTS 29
- /* YYNRULES -- Number of rules. */
--#define YYNRULES 80
--/* YYNSTATES -- Number of states. */
--#define YYNSTATES 144
-+#define YYNRULES 82
-+/* YYNRULES -- Number of states. */
-+#define YYNSTATES 147
-
--/* YYTRANSLATE[YYX] -- Symbol number corresponding to YYX as returned
-- by yylex, with out-of-bounds checking. */
-+/* YYTRANSLATE(YYLEX) -- Bison symbol number corresponding to YYLEX. */
- #define YYUNDEFTOK 2
--#define YYMAXUTOK 278
-+#define YYMAXUTOK 279
-
--#define YYTRANSLATE(YYX) \
-+#define YYTRANSLATE(YYX) \
- ((unsigned int) (YYX) <= YYMAXUTOK ? yytranslate[YYX] : YYUNDEFTOK)
-
--/* YYTRANSLATE[TOKEN-NUM] -- Symbol number corresponding to TOKEN-NUM
-- as returned by yylex, without out-of-bounds checking. */
-+/* YYTRANSLATE[YYLEX] -- Bison symbol number corresponding to YYLEX. */
- static const yytype_uint8 yytranslate[] =
- {
- 0, 2, 2, 2, 2, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
-- 2, 2, 2, 46, 2, 2, 2, 44, 40, 2,
-- 32, 34, 43, 41, 33, 42, 2, 25, 2, 2,
-- 2, 2, 2, 2, 2, 2, 2, 2, 37, 24,
-- 35, 28, 29, 36, 2, 2, 2, 2, 2, 2,
-+ 2, 2, 2, 47, 2, 2, 2, 45, 41, 2,
-+ 33, 35, 44, 42, 34, 43, 2, 26, 2, 2,
-+ 2, 2, 2, 2, 2, 2, 2, 2, 38, 25,
-+ 36, 29, 30, 37, 2, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
-- 2, 30, 2, 31, 39, 2, 2, 2, 2, 2,
-+ 2, 31, 2, 32, 40, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
-- 2, 2, 2, 26, 38, 27, 45, 2, 2, 2,
-+ 2, 2, 2, 27, 39, 28, 46, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
-@@ -486,292 +463,335 @@ static const yytype_uint8 yytranslate[]
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 1, 2, 3, 4,
- 5, 6, 7, 8, 9, 10, 11, 12, 13, 14,
-- 15, 16, 17, 18, 19, 20, 21, 22, 23
-+ 15, 16, 17, 18, 19, 20, 21, 22, 23, 24
- };
-
- #if YYDEBUG
-- /* YYRLINE[YYN] -- Source line where rule number YYN was defined. */
-+/* YYPRHS[YYN] -- Index of the first RHS symbol of rule number YYN in
-+ YYRHS. */
-+static const yytype_uint16 yyprhs[] =
-+{
-+ 0, 0, 3, 9, 10, 13, 14, 17, 22, 25,
-+ 28, 32, 37, 41, 46, 52, 53, 56, 61, 64,
-+ 68, 71, 74, 78, 83, 86, 96, 102, 105, 106,
-+ 109, 112, 116, 118, 121, 124, 127, 129, 131, 135,
-+ 137, 139, 145, 147, 151, 153, 157, 159, 163, 165,
-+ 169, 171, 175, 177, 181, 185, 187, 191, 195, 199,
-+ 203, 207, 211, 213, 217, 221, 223, 227, 231, 235,
-+ 237, 239, 242, 245, 248, 249, 252, 255, 256, 259,
-+ 262, 265, 269
-+};
-+
-+/* YYRHS -- A `-1'-separated list of the rules' RHS. */
-+static const yytype_int8 yyrhs[] =
-+{
-+ 49, 0, -1, 3, 25, 50, 51, 53, -1, -1,
-+ 4, 25, -1, -1, 52, 51, -1, 5, 60, 60,
-+ 25, -1, 22, 52, -1, 26, 54, -1, 53, 26,
-+ 54, -1, 53, 22, 23, 54, -1, 53, 23, 54,
-+ -1, 53, 16, 23, 25, -1, 27, 55, 75, 28,
-+ 25, -1, -1, 55, 56, -1, 17, 29, 57, 25,
-+ -1, 17, 25, -1, 15, 17, 25, -1, 22, 56,
-+ -1, 58, 21, -1, 58, 59, 30, -1, 58, 31,
-+ 74, 32, -1, 58, 23, -1, 58, 24, 33, 21,
-+ 34, 60, 34, 60, 35, -1, 58, 24, 33, 21,
-+ 35, -1, 57, 22, -1, -1, 57, 34, -1, 58,
-+ 22, -1, 14, 18, 36, -1, 36, -1, 59, 60,
-+ -1, 59, 23, -1, 59, 22, -1, 18, -1, 19,
-+ -1, 33, 61, 35, -1, 62, -1, 63, -1, 63,
-+ 37, 61, 38, 62, -1, 64, -1, 63, 13, 64,
-+ -1, 65, -1, 64, 12, 65, -1, 66, -1, 65,
-+ 39, 66, -1, 67, -1, 66, 40, 67, -1, 68,
-+ -1, 67, 41, 68, -1, 69, -1, 68, 10, 69,
-+ -1, 68, 11, 69, -1, 70, -1, 69, 36, 70,
-+ -1, 69, 30, 70, -1, 69, 8, 70, -1, 69,
-+ 9, 70, -1, 70, 6, 71, -1, 70, 7, 71,
-+ -1, 71, -1, 71, 42, 72, -1, 71, 43, 72,
-+ -1, 72, -1, 72, 44, 73, -1, 72, 26, 73,
-+ -1, 72, 45, 73, -1, 73, -1, 60, -1, 43,
-+ 73, -1, 46, 73, -1, 47, 73, -1, -1, 74,
-+ 20, -1, 74, 22, -1, -1, 76, 75, -1, 76,
-+ 56, -1, 17, 54, -1, 16, 17, 25, -1, 22,
-+ 76, -1
-+};
-+
-+/* YYRLINE[YYN] -- source line where rule number YYN was defined. */
- static const yytype_uint16 yyrline[] =
- {
-- 0, 104, 104, 113, 116, 123, 127, 135, 139, 144,
-- 155, 165, 180, 188, 191, 198, 202, 206, 210, 218,
-- 222, 226, 230, 234, 250, 260, 268, 271, 275, 282,
-- 298, 303, 322, 336, 343, 344, 345, 352, 356, 357,
-- 361, 362, 366, 367, 371, 372, 376, 377, 381, 382,
-- 386, 387, 388, 392, 393, 394, 395, 396, 400, 401,
-- 402, 406, 407, 408, 412, 413, 414, 415, 419, 420,
-- 421, 422, 427, 430, 434, 442, 445, 449, 457, 461,
-- 465
-+ 0, 108, 108, 119, 122, 130, 133, 140, 144, 152,
-+ 156, 161, 172, 182, 197, 205, 208, 215, 219, 223,
-+ 227, 235, 239, 243, 247, 251, 267, 277, 285, 288,
-+ 292, 299, 315, 320, 339, 353, 360, 361, 362, 369,
-+ 373, 374, 378, 379, 383, 384, 388, 389, 393, 394,
-+ 398, 399, 403, 404, 405, 409, 410, 411, 412, 413,
-+ 417, 418, 419, 423, 424, 425, 429, 430, 431, 432,
-+ 436, 437, 438, 439, 444, 447, 451, 459, 462, 466,
-+ 474, 478, 482
- };
- #endif
-
--#if YYDEBUG || YYERROR_VERBOSE || 0
-+#if YYDEBUG || YYERROR_VERBOSE || YYTOKEN_TABLE
- /* YYTNAME[SYMBOL-NUM] -- String name of the symbol SYMBOL-NUM.
- First, the terminals, then, starting at YYNTOKENS, nonterminals. */
- static const char *const yytname[] =
- {
-- "$end", "error", "$undefined", "DT_V1", "DT_MEMRESERVE", "DT_LSHIFT",
-- "DT_RSHIFT", "DT_LE", "DT_GE", "DT_EQ", "DT_NE", "DT_AND", "DT_OR",
-- "DT_BITS", "DT_DEL_PROP", "DT_DEL_NODE", "DT_PROPNODENAME", "DT_LITERAL",
-- "DT_CHAR_LITERAL", "DT_BYTE", "DT_STRING", "DT_LABEL", "DT_REF",
-- "DT_INCBIN", "';'", "'/'", "'{'", "'}'", "'='", "'>'", "'['", "']'",
-- "'('", "','", "')'", "'<'", "'?'", "':'", "'|'", "'^'", "'&'", "'+'",
-- "'-'", "'*'", "'%'", "'~'", "'!'", "$accept", "sourcefile",
-- "memreserves", "memreserve", "devicetree", "nodedef", "proplist",
-- "propdef", "propdata", "propdataprefix", "arrayprefix", "integer_prim",
-- "integer_expr", "integer_trinary", "integer_or", "integer_and",
-- "integer_bitor", "integer_bitxor", "integer_bitand", "integer_eq",
-- "integer_rela", "integer_shift", "integer_add", "integer_mul",
-- "integer_unary", "bytestring", "subnodes", "subnode", YY_NULLPTR
-+ "$end", "error", "$undefined", "DT_V1", "DT_PLUGIN", "DT_MEMRESERVE",
-+ "DT_LSHIFT", "DT_RSHIFT", "DT_LE", "DT_GE", "DT_EQ", "DT_NE", "DT_AND",
-+ "DT_OR", "DT_BITS", "DT_DEL_PROP", "DT_DEL_NODE", "DT_PROPNODENAME",
-+ "DT_LITERAL", "DT_CHAR_LITERAL", "DT_BYTE", "DT_STRING", "DT_LABEL",
-+ "DT_REF", "DT_INCBIN", "';'", "'/'", "'{'", "'}'", "'='", "'>'", "'['",
-+ "']'", "'('", "','", "')'", "'<'", "'?'", "':'", "'|'", "'^'", "'&'",
-+ "'+'", "'-'", "'*'", "'%'", "'~'", "'!'", "$accept", "sourcefile",
-+ "plugindecl", "memreserves", "memreserve", "devicetree", "nodedef",
-+ "proplist", "propdef", "propdata", "propdataprefix", "arrayprefix",
-+ "integer_prim", "integer_expr", "integer_trinary", "integer_or",
-+ "integer_and", "integer_bitor", "integer_bitxor", "integer_bitand",
-+ "integer_eq", "integer_rela", "integer_shift", "integer_add",
-+ "integer_mul", "integer_unary", "bytestring", "subnodes", "subnode", 0
- };
- #endif
-
- # ifdef YYPRINT
--/* YYTOKNUM[NUM] -- (External) token number corresponding to the
-- (internal) symbol number NUM (which must be that of a token). */
-+/* YYTOKNUM[YYLEX-NUM] -- Internal token number corresponding to
-+ token YYLEX-NUM. */
- static const yytype_uint16 yytoknum[] =
- {
- 0, 256, 257, 258, 259, 260, 261, 262, 263, 264,
- 265, 266, 267, 268, 269, 270, 271, 272, 273, 274,
-- 275, 276, 277, 278, 59, 47, 123, 125, 61, 62,
-- 91, 93, 40, 44, 41, 60, 63, 58, 124, 94,
-- 38, 43, 45, 42, 37, 126, 33
-+ 275, 276, 277, 278, 279, 59, 47, 123, 125, 61,
-+ 62, 91, 93, 40, 44, 41, 60, 63, 58, 124,
-+ 94, 38, 43, 45, 42, 37, 126, 33
- };
- # endif
-
--#define YYPACT_NINF -81
--
--#define yypact_value_is_default(Yystate) \
-- (!!((Yystate) == (-81)))
--
--#define YYTABLE_NINF -1
--
--#define yytable_value_is_error(Yytable_value) \
-- 0
--
-- /* YYPACT[STATE-NUM] -- Index in YYTABLE of the portion describing
-- STATE-NUM. */
--static const yytype_int8 yypact[] =
-+/* YYR1[YYN] -- Symbol number of symbol that rule YYN derives. */
-+static const yytype_uint8 yyr1[] =
- {
-- 16, -11, 21, 10, -81, 25, 10, 19, 10, -81,
-- -81, -9, 25, -81, 2, 51, -81, -9, -9, -9,
-- -81, 1, -81, -6, 50, 14, 28, 29, 36, 3,
-- 58, 44, -3, -81, 47, -81, -81, 65, 68, 2,
-- 2, -81, -81, -81, -81, -9, -9, -9, -9, -9,
-- -9, -9, -9, -9, -9, -9, -9, -9, -9, -9,
-- -9, -9, -9, -9, -81, 63, 69, 2, -81, -81,
-- 50, 57, 14, 28, 29, 36, 3, 3, 58, 58,
-- 58, 58, 44, 44, -3, -3, -81, -81, -81, 79,
-- 80, -8, 63, -81, 72, 63, -81, -81, -9, 76,
-- 77, -81, -81, -81, -81, -81, 78, -81, -81, -81,
-- -81, -81, 35, 4, -81, -81, -81, -81, 86, -81,
-- -81, -81, 73, -81, -81, 33, 71, 84, 39, -81,
-- -81, -81, -81, -81, 41, -81, -81, -81, 25, -81,
-- 74, 25, 75, -81
-+ 0, 48, 49, 50, 50, 51, 51, 52, 52, 53,
-+ 53, 53, 53, 53, 54, 55, 55, 56, 56, 56,
-+ 56, 57, 57, 57, 57, 57, 57, 57, 58, 58,
-+ 58, 59, 59, 59, 59, 59, 60, 60, 60, 61,
-+ 62, 62, 63, 63, 64, 64, 65, 65, 66, 66,
-+ 67, 67, 68, 68, 68, 69, 69, 69, 69, 69,
-+ 70, 70, 70, 71, 71, 71, 72, 72, 72, 72,
-+ 73, 73, 73, 73, 74, 74, 74, 75, 75, 75,
-+ 76, 76, 76
- };
-
-- /* YYDEFACT[STATE-NUM] -- Default reduction number in state STATE-NUM.
-- Performed when YYTABLE does not specify something else to do. Zero
-- means the default is an error. */
--static const yytype_uint8 yydefact[] =
-+/* YYR2[YYN] -- Number of symbols composing right hand side of rule YYN. */
-+static const yytype_uint8 yyr2[] =
- {
-- 0, 0, 0, 3, 1, 0, 0, 0, 3, 34,
-- 35, 0, 0, 6, 0, 2, 4, 0, 0, 0,
-- 68, 0, 37, 38, 40, 42, 44, 46, 48, 50,
-- 53, 60, 63, 67, 0, 13, 7, 0, 0, 0,
-- 0, 69, 70, 71, 36, 0, 0, 0, 0, 0,
-- 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
-- 0, 0, 0, 0, 5, 75, 0, 0, 10, 8,
-- 41, 0, 43, 45, 47, 49, 51, 52, 56, 57,
-- 55, 54, 58, 59, 61, 62, 65, 64, 66, 0,
-- 0, 0, 0, 14, 0, 75, 11, 9, 0, 0,
-- 0, 16, 26, 78, 18, 80, 0, 77, 76, 39,
-- 17, 79, 0, 0, 12, 25, 15, 27, 0, 19,
-- 28, 22, 0, 72, 30, 0, 0, 0, 0, 33,
-- 32, 20, 31, 29, 0, 73, 74, 21, 0, 24,
-- 0, 0, 0, 23
-+ 0, 2, 5, 0, 2, 0, 2, 4, 2, 2,
-+ 3, 4, 3, 4, 5, 0, 2, 4, 2, 3,
-+ 2, 2, 3, 4, 2, 9, 5, 2, 0, 2,
-+ 2, 3, 1, 2, 2, 2, 1, 1, 3, 1,
-+ 1, 5, 1, 3, 1, 3, 1, 3, 1, 3,
-+ 1, 3, 1, 3, 3, 1, 3, 3, 3, 3,
-+ 3, 3, 1, 3, 3, 1, 3, 3, 3, 1,
-+ 1, 2, 2, 2, 0, 2, 2, 0, 2, 2,
-+ 2, 3, 2
- };
-
-- /* YYPGOTO[NTERM-NUM]. */
--static const yytype_int8 yypgoto[] =
-+/* YYDEFACT[STATE-NAME] -- Default reduction number in state STATE-NUM.
-+ Performed when YYTABLE doesn't specify something else to do. Zero
-+ means the default is an error. */
-+static const yytype_uint8 yydefact[] =
- {
-- -81, -81, 100, 104, -81, -38, -81, -80, -81, -81,
-- -81, -5, 66, 13, -81, 70, 67, 81, 64, 82,
-- 37, 27, 34, 38, -14, -81, 22, 24
-+ 0, 0, 0, 3, 1, 0, 5, 4, 0, 0,
-+ 0, 5, 36, 37, 0, 0, 8, 0, 2, 6,
-+ 0, 0, 0, 70, 0, 39, 40, 42, 44, 46,
-+ 48, 50, 52, 55, 62, 65, 69, 0, 15, 9,
-+ 0, 0, 0, 0, 71, 72, 73, 38, 0, 0,
-+ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
-+ 0, 0, 0, 0, 0, 0, 0, 7, 77, 0,
-+ 0, 12, 10, 43, 0, 45, 47, 49, 51, 53,
-+ 54, 58, 59, 57, 56, 60, 61, 63, 64, 67,
-+ 66, 68, 0, 0, 0, 0, 16, 0, 77, 13,
-+ 11, 0, 0, 0, 18, 28, 80, 20, 82, 0,
-+ 79, 78, 41, 19, 81, 0, 0, 14, 27, 17,
-+ 29, 0, 21, 30, 24, 0, 74, 32, 0, 0,
-+ 0, 0, 35, 34, 22, 33, 31, 0, 75, 76,
-+ 23, 0, 26, 0, 0, 0, 25
- };
-
-- /* YYDEFGOTO[NTERM-NUM]. */
-+/* YYDEFGOTO[NTERM-NUM]. */
- static const yytype_int16 yydefgoto[] =
- {
-- -1, 2, 7, 8, 15, 36, 65, 93, 112, 113,
-- 125, 20, 21, 22, 23, 24, 25, 26, 27, 28,
-- 29, 30, 31, 32, 33, 128, 94, 95
-+ -1, 2, 6, 10, 11, 18, 39, 68, 96, 115,
-+ 116, 128, 23, 24, 25, 26, 27, 28, 29, 30,
-+ 31, 32, 33, 34, 35, 36, 131, 97, 98
- };
-
-- /* YYTABLE[YYPACT[STATE-NUM]] -- What to do in state STATE-NUM. If
-- positive, shift that token. If negative, reduce the rule whose
-- number is the opposite. If YYTABLE_NINF, syntax error. */
--static const yytype_uint8 yytable[] =
-+/* YYPACT[STATE-NUM] -- Index in YYTABLE of the portion describing
-+ STATE-NUM. */
-+#define YYPACT_NINF -84
-+static const yytype_int8 yypact[] =
- {
-- 12, 68, 69, 41, 42, 43, 45, 34, 9, 10,
-- 53, 54, 104, 3, 5, 107, 101, 118, 35, 1,
-- 102, 4, 61, 11, 119, 120, 121, 122, 35, 97,
-- 46, 6, 55, 17, 123, 44, 18, 19, 56, 124,
-- 62, 63, 9, 10, 14, 51, 52, 86, 87, 88,
-- 9, 10, 48, 103, 129, 130, 115, 11, 135, 116,
-- 136, 47, 131, 57, 58, 11, 37, 49, 117, 50,
-- 137, 64, 38, 39, 138, 139, 40, 89, 90, 91,
-- 78, 79, 80, 81, 92, 59, 60, 66, 76, 77,
-- 67, 82, 83, 96, 98, 99, 100, 84, 85, 106,
-- 110, 111, 114, 126, 134, 127, 133, 141, 16, 143,
-- 13, 109, 71, 74, 72, 70, 105, 108, 0, 0,
-- 132, 0, 0, 0, 0, 0, 0, 0, 0, 73,
-- 0, 0, 75, 140, 0, 0, 142
-+ 15, -12, 35, 42, -84, 27, 9, -84, 24, 9,
-+ 43, 9, -84, -84, -10, 24, -84, 60, 44, -84,
-+ -10, -10, -10, -84, 55, -84, -7, 52, 53, 51,
-+ 54, 10, 2, 38, 37, -4, -84, 68, -84, -84,
-+ 71, 73, 60, 60, -84, -84, -84, -84, -10, -10,
-+ -10, -10, -10, -10, -10, -10, -10, -10, -10, -10,
-+ -10, -10, -10, -10, -10, -10, -10, -84, 56, 72,
-+ 60, -84, -84, 52, 61, 53, 51, 54, 10, 2,
-+ 2, 38, 38, 38, 38, 37, 37, -4, -4, -84,
-+ -84, -84, 81, 83, 34, 56, -84, 74, 56, -84,
-+ -84, -10, 76, 78, -84, -84, -84, -84, -84, 79,
-+ -84, -84, -84, -84, -84, -6, 3, -84, -84, -84,
-+ -84, 87, -84, -84, -84, 75, -84, -84, 32, 70,
-+ 86, 36, -84, -84, -84, -84, -84, 47, -84, -84,
-+ -84, 24, -84, 77, 24, 80, -84
- };
-
--static const yytype_int16 yycheck[] =
-+/* YYPGOTO[NTERM-NUM]. */
-+static const yytype_int8 yypgoto[] =
- {
-- 5, 39, 40, 17, 18, 19, 12, 12, 17, 18,
-- 7, 8, 92, 24, 4, 95, 24, 13, 26, 3,
-- 28, 0, 25, 32, 20, 21, 22, 23, 26, 67,
-- 36, 21, 29, 42, 30, 34, 45, 46, 35, 35,
-- 43, 44, 17, 18, 25, 9, 10, 61, 62, 63,
-- 17, 18, 38, 91, 21, 22, 21, 32, 19, 24,
-- 21, 11, 29, 5, 6, 32, 15, 39, 33, 40,
-- 31, 24, 21, 22, 33, 34, 25, 14, 15, 16,
-- 53, 54, 55, 56, 21, 41, 42, 22, 51, 52,
-- 22, 57, 58, 24, 37, 16, 16, 59, 60, 27,
-- 24, 24, 24, 17, 20, 32, 35, 33, 8, 34,
-- 6, 98, 46, 49, 47, 45, 92, 95, -1, -1,
-- 125, -1, -1, -1, -1, -1, -1, -1, -1, 48,
-- -1, -1, 50, 138, -1, -1, 141
-+ -84, -84, -84, 98, 101, -84, -41, -84, -83, -84,
-+ -84, -84, -8, 63, 12, -84, 66, 67, 65, 69,
-+ 82, 29, 18, 25, 26, -17, -84, 20, 28
- };
-
-- /* YYSTOS[STATE-NUM] -- The (internal number of the) accessing
-- symbol of state STATE-NUM. */
--static const yytype_uint8 yystos[] =
-+/* YYTABLE[YYPACT[STATE-NUM]]. What to do in state STATE-NUM. If
-+ positive, shift that token. If negative, reduce the rule which
-+ number is the opposite. If YYTABLE_NINF, syntax error. */
-+#define YYTABLE_NINF -1
-+static const yytype_uint8 yytable[] =
- {
-- 0, 3, 48, 24, 0, 4, 21, 49, 50, 17,
-- 18, 32, 58, 50, 25, 51, 49, 42, 45, 46,
-- 58, 59, 60, 61, 62, 63, 64, 65, 66, 67,
-- 68, 69, 70, 71, 58, 26, 52, 15, 21, 22,
-- 25, 71, 71, 71, 34, 12, 36, 11, 38, 39,
-- 40, 9, 10, 7, 8, 29, 35, 5, 6, 41,
-- 42, 25, 43, 44, 24, 53, 22, 22, 52, 52,
-- 62, 59, 63, 64, 65, 66, 67, 67, 68, 68,
-- 68, 68, 69, 69, 70, 70, 71, 71, 71, 14,
-- 15, 16, 21, 54, 73, 74, 24, 52, 37, 16,
-- 16, 24, 28, 52, 54, 74, 27, 54, 73, 60,
-- 24, 24, 55, 56, 24, 21, 24, 33, 13, 20,
-- 21, 22, 23, 30, 35, 57, 17, 32, 72, 21,
-- 22, 29, 58, 35, 20, 19, 21, 31, 33, 34,
-- 58, 33, 58, 34
-+ 15, 71, 72, 44, 45, 46, 48, 37, 12, 13,
-+ 56, 57, 107, 3, 8, 110, 118, 121, 1, 119,
-+ 54, 55, 64, 14, 122, 123, 124, 125, 120, 100,
-+ 49, 9, 58, 20, 126, 4, 21, 22, 59, 127,
-+ 65, 66, 12, 13, 60, 61, 5, 89, 90, 91,
-+ 12, 13, 7, 106, 132, 133, 138, 14, 139, 104,
-+ 40, 38, 134, 105, 50, 14, 41, 42, 140, 17,
-+ 43, 92, 93, 94, 81, 82, 83, 84, 95, 62,
-+ 63, 141, 142, 79, 80, 85, 86, 38, 87, 88,
-+ 47, 52, 51, 67, 69, 53, 70, 99, 102, 101,
-+ 103, 113, 109, 114, 117, 129, 136, 137, 130, 19,
-+ 16, 144, 74, 112, 73, 146, 76, 75, 111, 0,
-+ 135, 77, 0, 108, 0, 0, 0, 0, 0, 0,
-+ 0, 0, 0, 143, 0, 78, 145
- };
-
-- /* YYR1[YYN] -- Symbol number of symbol that rule YYN derives. */
--static const yytype_uint8 yyr1[] =
-+#define yypact_value_is_default(yystate) \
-+ ((yystate) == (-84))
-+
-+#define yytable_value_is_error(yytable_value) \
-+ YYID (0)
-+
-+static const yytype_int16 yycheck[] =
- {
-- 0, 47, 48, 49, 49, 50, 50, 51, 51, 51,
-- 51, 51, 52, 53, 53, 54, 54, 54, 54, 55,
-- 55, 55, 55, 55, 55, 55, 56, 56, 56, 57,
-- 57, 57, 57, 57, 58, 58, 58, 59, 60, 60,
-- 61, 61, 62, 62, 63, 63, 64, 64, 65, 65,
-- 66, 66, 66, 67, 67, 67, 67, 67, 68, 68,
-- 68, 69, 69, 69, 70, 70, 70, 70, 71, 71,
-- 71, 71, 72, 72, 72, 73, 73, 73, 74, 74,
-- 74
-+ 8, 42, 43, 20, 21, 22, 13, 15, 18, 19,
-+ 8, 9, 95, 25, 5, 98, 22, 14, 3, 25,
-+ 10, 11, 26, 33, 21, 22, 23, 24, 34, 70,
-+ 37, 22, 30, 43, 31, 0, 46, 47, 36, 36,
-+ 44, 45, 18, 19, 6, 7, 4, 64, 65, 66,
-+ 18, 19, 25, 94, 22, 23, 20, 33, 22, 25,
-+ 16, 27, 30, 29, 12, 33, 22, 23, 32, 26,
-+ 26, 15, 16, 17, 56, 57, 58, 59, 22, 42,
-+ 43, 34, 35, 54, 55, 60, 61, 27, 62, 63,
-+ 35, 40, 39, 25, 23, 41, 23, 25, 17, 38,
-+ 17, 25, 28, 25, 25, 18, 36, 21, 33, 11,
-+ 9, 34, 49, 101, 48, 35, 51, 50, 98, -1,
-+ 128, 52, -1, 95, -1, -1, -1, -1, -1, -1,
-+ -1, -1, -1, 141, -1, 53, 144
- };
-
-- /* YYR2[YYN] -- Number of symbols on the right hand side of rule YYN. */
--static const yytype_uint8 yyr2[] =
-+/* YYSTOS[STATE-NUM] -- The (internal number of the) accessing
-+ symbol of state STATE-NUM. */
-+static const yytype_uint8 yystos[] =
- {
-- 0, 2, 4, 0, 2, 4, 2, 2, 3, 4,
-- 3, 4, 5, 0, 2, 4, 2, 3, 2, 2,
-- 3, 4, 2, 9, 5, 2, 0, 2, 2, 3,
-- 1, 2, 2, 2, 1, 1, 3, 1, 1, 5,
-- 1, 3, 1, 3, 1, 3, 1, 3, 1, 3,
-- 1, 3, 3, 1, 3, 3, 3, 3, 3, 3,
-- 1, 3, 3, 1, 3, 3, 3, 1, 1, 2,
-- 2, 2, 0, 2, 2, 0, 2, 2, 2, 3,
-- 2
-+ 0, 3, 49, 25, 0, 4, 50, 25, 5, 22,
-+ 51, 52, 18, 19, 33, 60, 52, 26, 53, 51,
-+ 43, 46, 47, 60, 61, 62, 63, 64, 65, 66,
-+ 67, 68, 69, 70, 71, 72, 73, 60, 27, 54,
-+ 16, 22, 23, 26, 73, 73, 73, 35, 13, 37,
-+ 12, 39, 40, 41, 10, 11, 8, 9, 30, 36,
-+ 6, 7, 42, 43, 26, 44, 45, 25, 55, 23,
-+ 23, 54, 54, 64, 61, 65, 66, 67, 68, 69,
-+ 69, 70, 70, 70, 70, 71, 71, 72, 72, 73,
-+ 73, 73, 15, 16, 17, 22, 56, 75, 76, 25,
-+ 54, 38, 17, 17, 25, 29, 54, 56, 76, 28,
-+ 56, 75, 62, 25, 25, 57, 58, 25, 22, 25,
-+ 34, 14, 21, 22, 23, 24, 31, 36, 59, 18,
-+ 33, 74, 22, 23, 30, 60, 36, 21, 20, 22,
-+ 32, 34, 35, 60, 34, 60, 35
- };
-
--
--#define yyerrok (yyerrstatus = 0)
--#define yyclearin (yychar = YYEMPTY)
--#define YYEMPTY (-2)
--#define YYEOF 0
--
--#define YYACCEPT goto yyacceptlab
--#define YYABORT goto yyabortlab
--#define YYERROR goto yyerrorlab
--
-+#define yyerrok (yyerrstatus = 0)
-+#define yyclearin (yychar = YYEMPTY)
-+#define YYEMPTY (-2)
-+#define YYEOF 0
-+
-+#define YYACCEPT goto yyacceptlab
-+#define YYABORT goto yyabortlab
-+#define YYERROR goto yyerrorlab
-+
-+
-+/* Like YYERROR except do call yyerror. This remains here temporarily
-+ to ease the transition to the new meaning of YYERROR, for GCC.
-+ Once GCC version 2 has supplanted version 1, this can go. However,
-+ YYFAIL appears to be in use. Nevertheless, it is formally deprecated
-+ in Bison 2.4.2's NEWS entry, where a plan to phase it out is
-+ discussed. */
-+
-+#define YYFAIL goto yyerrlab
-+#if defined YYFAIL
-+ /* This is here to suppress warnings from the GCC cpp's
-+ -Wunused-macros. Normally we don't worry about that warning, but
-+ some users do, and we want to make it easy for users to remove
-+ YYFAIL uses, which will produce warnings from Bison 2.5. */
-+#endif
-
- #define YYRECOVERING() (!!yyerrstatus)
-
--#define YYBACKUP(Token, Value) \
--do \
-- if (yychar == YYEMPTY) \
-- { \
-- yychar = (Token); \
-- yylval = (Value); \
-- YYPOPSTACK (yylen); \
-- yystate = *yyssp; \
-- goto yybackup; \
-- } \
-- else \
-- { \
-+#define YYBACKUP(Token, Value) \
-+do \
-+ if (yychar == YYEMPTY && yylen == 1) \
-+ { \
-+ yychar = (Token); \
-+ yylval = (Value); \
-+ YYPOPSTACK (1); \
-+ goto yybackup; \
-+ } \
-+ else \
-+ { \
- yyerror (YY_("syntax error: cannot back up")); \
-- YYERROR; \
-- } \
--while (0)
--
--/* Error token number */
--#define YYTERROR 1
--#define YYERRCODE 256
-+ YYERROR; \
-+ } \
-+while (YYID (0))
-+
-+
-+#define YYTERROR 1
-+#define YYERRCODE 256
-
-
- /* YYLLOC_DEFAULT -- Set CURRENT to span from RHS[1] to RHS[N].
- If N is 0, then set CURRENT to the empty location which ends
- the previous symbol: RHS[0] (always defined). */
-
-+#define YYRHSLOC(Rhs, K) ((Rhs)[K])
- #ifndef YYLLOC_DEFAULT
--# define YYLLOC_DEFAULT(Current, Rhs, N) \
-- do \
-- if (N) \
-- { \
-- (Current).first_line = YYRHSLOC (Rhs, 1).first_line; \
-- (Current).first_column = YYRHSLOC (Rhs, 1).first_column; \
-- (Current).last_line = YYRHSLOC (Rhs, N).last_line; \
-- (Current).last_column = YYRHSLOC (Rhs, N).last_column; \
-- } \
-- else \
-- { \
-- (Current).first_line = (Current).last_line = \
-- YYRHSLOC (Rhs, 0).last_line; \
-- (Current).first_column = (Current).last_column = \
-- YYRHSLOC (Rhs, 0).last_column; \
-- } \
-- while (0)
-+# define YYLLOC_DEFAULT(Current, Rhs, N) \
-+ do \
-+ if (YYID (N)) \
-+ { \
-+ (Current).first_line = YYRHSLOC (Rhs, 1).first_line; \
-+ (Current).first_column = YYRHSLOC (Rhs, 1).first_column; \
-+ (Current).last_line = YYRHSLOC (Rhs, N).last_line; \
-+ (Current).last_column = YYRHSLOC (Rhs, N).last_column; \
-+ } \
-+ else \
-+ { \
-+ (Current).first_line = (Current).last_line = \
-+ YYRHSLOC (Rhs, 0).last_line; \
-+ (Current).first_column = (Current).last_column = \
-+ YYRHSLOC (Rhs, 0).last_column; \
-+ } \
-+ while (YYID (0))
- #endif
-
--#define YYRHSLOC(Rhs, K) ((Rhs)[K])
--
--
--/* Enable debugging if requested. */
--#if YYDEBUG
--
--# ifndef YYFPRINTF
--# include <stdio.h> /* INFRINGES ON USER NAME SPACE */
--# define YYFPRINTF fprintf
--# endif
--
--# define YYDPRINTF(Args) \
--do { \
-- if (yydebug) \
-- YYFPRINTF Args; \
--} while (0)
--
-
- /* YY_LOCATION_PRINT -- Print the location on the stream.
- This macro was not mandated originally: define only if we know
-@@ -779,73 +799,82 @@ do {
-
- #ifndef YY_LOCATION_PRINT
- # if defined YYLTYPE_IS_TRIVIAL && YYLTYPE_IS_TRIVIAL
--
--/* Print *YYLOCP on YYO. Private, do not rely on its existence. */
--
--YY_ATTRIBUTE_UNUSED
--static unsigned
--yy_location_print_ (FILE *yyo, YYLTYPE const * const yylocp)
--{
-- unsigned res = 0;
-- int end_col = 0 != yylocp->last_column ? yylocp->last_column - 1 : 0;
-- if (0 <= yylocp->first_line)
-- {
-- res += YYFPRINTF (yyo, "%d", yylocp->first_line);
-- if (0 <= yylocp->first_column)
-- res += YYFPRINTF (yyo, ".%d", yylocp->first_column);
-- }
-- if (0 <= yylocp->last_line)
-- {
-- if (yylocp->first_line < yylocp->last_line)
-- {
-- res += YYFPRINTF (yyo, "-%d", yylocp->last_line);
-- if (0 <= end_col)
-- res += YYFPRINTF (yyo, ".%d", end_col);
-- }
-- else if (0 <= end_col && yylocp->first_column < end_col)
-- res += YYFPRINTF (yyo, "-%d", end_col);
-- }
-- return res;
-- }
--
--# define YY_LOCATION_PRINT(File, Loc) \
-- yy_location_print_ (File, &(Loc))
--
-+# define YY_LOCATION_PRINT(File, Loc) \
-+ fprintf (File, "%d.%d-%d.%d", \
-+ (Loc).first_line, (Loc).first_column, \
-+ (Loc).last_line, (Loc).last_column)
- # else
- # define YY_LOCATION_PRINT(File, Loc) ((void) 0)
- # endif
- #endif
-
-
--# define YY_SYMBOL_PRINT(Title, Type, Value, Location) \
--do { \
-- if (yydebug) \
-- { \
-- YYFPRINTF (stderr, "%s ", Title); \
-- yy_symbol_print (stderr, \
-- Type, Value, Location); \
-- YYFPRINTF (stderr, "\n"); \
-- } \
--} while (0)
-+/* YYLEX -- calling `yylex' with the right arguments. */
-
-+#ifdef YYLEX_PARAM
-+# define YYLEX yylex (YYLEX_PARAM)
-+#else
-+# define YYLEX yylex ()
-+#endif
-
--/*----------------------------------------.
--| Print this symbol's value on YYOUTPUT. |
--`----------------------------------------*/
-+/* Enable debugging if requested. */
-+#if YYDEBUG
-
-+# ifndef YYFPRINTF
-+# include <stdio.h> /* INFRINGES ON USER NAME SPACE */
-+# define YYFPRINTF fprintf
-+# endif
-+
-+# define YYDPRINTF(Args) \
-+do { \
-+ if (yydebug) \
-+ YYFPRINTF Args; \
-+} while (YYID (0))
-+
-+# define YY_SYMBOL_PRINT(Title, Type, Value, Location) \
-+do { \
-+ if (yydebug) \
-+ { \
-+ YYFPRINTF (stderr, "%s ", Title); \
-+ yy_symbol_print (stderr, \
-+ Type, Value, Location); \
-+ YYFPRINTF (stderr, "\n"); \
-+ } \
-+} while (YYID (0))
-+
-+
-+/*--------------------------------.
-+| Print this symbol on YYOUTPUT. |
-+`--------------------------------*/
-+
-+/*ARGSUSED*/
-+#if (defined __STDC__ || defined __C99__FUNC__ \
-+ || defined __cplusplus || defined _MSC_VER)
- static void
- yy_symbol_value_print (FILE *yyoutput, int yytype, YYSTYPE const * const yyvaluep, YYLTYPE const * const yylocationp)
-+#else
-+static void
-+yy_symbol_value_print (yyoutput, yytype, yyvaluep, yylocationp)
-+ FILE *yyoutput;
-+ int yytype;
-+ YYSTYPE const * const yyvaluep;
-+ YYLTYPE const * const yylocationp;
-+#endif
- {
-- FILE *yyo = yyoutput;
-- YYUSE (yyo);
-- YYUSE (yylocationp);
- if (!yyvaluep)
- return;
-+ YYUSE (yylocationp);
- # ifdef YYPRINT
- if (yytype < YYNTOKENS)
- YYPRINT (yyoutput, yytoknum[yytype], *yyvaluep);
-+# else
-+ YYUSE (yyoutput);
- # endif
-- YYUSE (yytype);
-+ switch (yytype)
-+ {
-+ default:
-+ break;
-+ }
- }
-
-
-@@ -853,11 +882,23 @@ yy_symbol_value_print (FILE *yyoutput, i
- | Print this symbol on YYOUTPUT. |
- `--------------------------------*/
-
-+#if (defined __STDC__ || defined __C99__FUNC__ \
-+ || defined __cplusplus || defined _MSC_VER)
- static void
- yy_symbol_print (FILE *yyoutput, int yytype, YYSTYPE const * const yyvaluep, YYLTYPE const * const yylocationp)
-+#else
-+static void
-+yy_symbol_print (yyoutput, yytype, yyvaluep, yylocationp)
-+ FILE *yyoutput;
-+ int yytype;
-+ YYSTYPE const * const yyvaluep;
-+ YYLTYPE const * const yylocationp;
-+#endif
- {
-- YYFPRINTF (yyoutput, "%s %s (",
-- yytype < YYNTOKENS ? "token" : "nterm", yytname[yytype]);
-+ if (yytype < YYNTOKENS)
-+ YYFPRINTF (yyoutput, "token %s (", yytname[yytype]);
-+ else
-+ YYFPRINTF (yyoutput, "nterm %s (", yytname[yytype]);
-
- YY_LOCATION_PRINT (yyoutput, *yylocationp);
- YYFPRINTF (yyoutput, ": ");
-@@ -870,8 +911,16 @@ yy_symbol_print (FILE *yyoutput, int yyt
- | TOP (included). |
- `------------------------------------------------------------------*/
-
-+#if (defined __STDC__ || defined __C99__FUNC__ \
-+ || defined __cplusplus || defined _MSC_VER)
- static void
- yy_stack_print (yytype_int16 *yybottom, yytype_int16 *yytop)
-+#else
-+static void
-+yy_stack_print (yybottom, yytop)
-+ yytype_int16 *yybottom;
-+ yytype_int16 *yytop;
-+#endif
- {
- YYFPRINTF (stderr, "Stack now");
- for (; yybottom <= yytop; yybottom++)
-@@ -882,42 +931,50 @@ yy_stack_print (yytype_int16 *yybottom,
- YYFPRINTF (stderr, "\n");
- }
-
--# define YY_STACK_PRINT(Bottom, Top) \
--do { \
-- if (yydebug) \
-- yy_stack_print ((Bottom), (Top)); \
--} while (0)
-+# define YY_STACK_PRINT(Bottom, Top) \
-+do { \
-+ if (yydebug) \
-+ yy_stack_print ((Bottom), (Top)); \
-+} while (YYID (0))
-
-
- /*------------------------------------------------.
- | Report that the YYRULE is going to be reduced. |
- `------------------------------------------------*/
-
-+#if (defined __STDC__ || defined __C99__FUNC__ \
-+ || defined __cplusplus || defined _MSC_VER)
-+static void
-+yy_reduce_print (YYSTYPE *yyvsp, YYLTYPE *yylsp, int yyrule)
-+#else
- static void
--yy_reduce_print (yytype_int16 *yyssp, YYSTYPE *yyvsp, YYLTYPE *yylsp, int yyrule)
-+yy_reduce_print (yyvsp, yylsp, yyrule)
-+ YYSTYPE *yyvsp;
-+ YYLTYPE *yylsp;
-+ int yyrule;
-+#endif
- {
-- unsigned long int yylno = yyrline[yyrule];
- int yynrhs = yyr2[yyrule];
- int yyi;
-+ unsigned long int yylno = yyrline[yyrule];
- YYFPRINTF (stderr, "Reducing stack by rule %d (line %lu):\n",
-- yyrule - 1, yylno);
-+ yyrule - 1, yylno);
- /* The symbols being reduced. */
- for (yyi = 0; yyi < yynrhs; yyi++)
- {
- YYFPRINTF (stderr, " $%d = ", yyi + 1);
-- yy_symbol_print (stderr,
-- yystos[yyssp[yyi + 1 - yynrhs]],
-- &(yyvsp[(yyi + 1) - (yynrhs)])
-- , &(yylsp[(yyi + 1) - (yynrhs)]) );
-+ yy_symbol_print (stderr, yyrhs[yyprhs[yyrule] + yyi],
-+ &(yyvsp[(yyi + 1) - (yynrhs)])
-+ , &(yylsp[(yyi + 1) - (yynrhs)]) );
- YYFPRINTF (stderr, "\n");
- }
- }
-
--# define YY_REDUCE_PRINT(Rule) \
--do { \
-- if (yydebug) \
-- yy_reduce_print (yyssp, yyvsp, yylsp, Rule); \
--} while (0)
-+# define YY_REDUCE_PRINT(Rule) \
-+do { \
-+ if (yydebug) \
-+ yy_reduce_print (yyvsp, yylsp, Rule); \
-+} while (YYID (0))
-
- /* Nonzero means print parse trace. It is left uninitialized so that
- multiple parsers can coexist. */
-@@ -931,7 +988,7 @@ int yydebug;
-
-
- /* YYINITDEPTH -- initial size of the parser's stacks. */
--#ifndef YYINITDEPTH
-+#ifndef YYINITDEPTH
- # define YYINITDEPTH 200
- #endif
-
-@@ -954,8 +1011,15 @@ int yydebug;
- # define yystrlen strlen
- # else
- /* Return the length of YYSTR. */
-+#if (defined __STDC__ || defined __C99__FUNC__ \
-+ || defined __cplusplus || defined _MSC_VER)
- static YYSIZE_T
- yystrlen (const char *yystr)
-+#else
-+static YYSIZE_T
-+yystrlen (yystr)
-+ const char *yystr;
-+#endif
- {
- YYSIZE_T yylen;
- for (yylen = 0; yystr[yylen]; yylen++)
-@@ -971,8 +1035,16 @@ yystrlen (const char *yystr)
- # else
- /* Copy YYSRC to YYDEST, returning the address of the terminating '\0' in
- YYDEST. */
-+#if (defined __STDC__ || defined __C99__FUNC__ \
-+ || defined __cplusplus || defined _MSC_VER)
- static char *
- yystpcpy (char *yydest, const char *yysrc)
-+#else
-+static char *
-+yystpcpy (yydest, yysrc)
-+ char *yydest;
-+ const char *yysrc;
-+#endif
- {
- char *yyd = yydest;
- const char *yys = yysrc;
-@@ -1002,27 +1074,27 @@ yytnamerr (char *yyres, const char *yyst
- char const *yyp = yystr;
-
- for (;;)
-- switch (*++yyp)
-- {
-- case '\'':
-- case ',':
-- goto do_not_strip_quotes;
--
-- case '\\':
-- if (*++yyp != '\\')
-- goto do_not_strip_quotes;
-- /* Fall through. */
-- default:
-- if (yyres)
-- yyres[yyn] = *yyp;
-- yyn++;
-- break;
--
-- case '"':
-- if (yyres)
-- yyres[yyn] = '\0';
-- return yyn;
-- }
-+ switch (*++yyp)
-+ {
-+ case '\'':
-+ case ',':
-+ goto do_not_strip_quotes;
-+
-+ case '\\':
-+ if (*++yyp != '\\')
-+ goto do_not_strip_quotes;
-+ /* Fall through. */
-+ default:
-+ if (yyres)
-+ yyres[yyn] = *yyp;
-+ yyn++;
-+ break;
-+
-+ case '"':
-+ if (yyres)
-+ yyres[yyn] = '\0';
-+ return yyn;
-+ }
- do_not_strip_quotes: ;
- }
-
-@@ -1045,11 +1117,12 @@ static int
- yysyntax_error (YYSIZE_T *yymsg_alloc, char **yymsg,
- yytype_int16 *yyssp, int yytoken)
- {
-- YYSIZE_T yysize0 = yytnamerr (YY_NULLPTR, yytname[yytoken]);
-+ YYSIZE_T yysize0 = yytnamerr (0, yytname[yytoken]);
- YYSIZE_T yysize = yysize0;
-+ YYSIZE_T yysize1;
- enum { YYERROR_VERBOSE_ARGS_MAXIMUM = 5 };
- /* Internationalized format string. */
-- const char *yyformat = YY_NULLPTR;
-+ const char *yyformat = 0;
- /* Arguments of yyformat. */
- char const *yyarg[YYERROR_VERBOSE_ARGS_MAXIMUM];
- /* Number of reported tokens (one for the "unexpected", one per
-@@ -1057,6 +1130,10 @@ yysyntax_error (YYSIZE_T *yymsg_alloc, c
- int yycount = 0;
-
- /* There are many possibilities here to consider:
-+ - Assume YYFAIL is not used. It's too flawed to consider. See
-+ <http://lists.gnu.org/archive/html/bison-patches/2009-12/msg00024.html>
-+ for details. YYERROR is fine as it does not invoke this
-+ function.
- - If this state is a consistent state with a default action, then
- the only way this function was invoked is if the default action
- is an error action. In that case, don't check for expected
-@@ -1105,13 +1182,11 @@ yysyntax_error (YYSIZE_T *yymsg_alloc, c
- break;
- }
- yyarg[yycount++] = yytname[yyx];
-- {
-- YYSIZE_T yysize1 = yysize + yytnamerr (YY_NULLPTR, yytname[yyx]);
-- if (! (yysize <= yysize1
-- && yysize1 <= YYSTACK_ALLOC_MAXIMUM))
-- return 2;
-- yysize = yysize1;
-- }
-+ yysize1 = yysize + yytnamerr (0, yytname[yyx]);
-+ if (! (yysize <= yysize1
-+ && yysize1 <= YYSTACK_ALLOC_MAXIMUM))
-+ return 2;
-+ yysize = yysize1;
- }
- }
- }
-@@ -1131,12 +1206,10 @@ yysyntax_error (YYSIZE_T *yymsg_alloc, c
- # undef YYCASE_
- }
-
-- {
-- YYSIZE_T yysize1 = yysize + yystrlen (yyformat);
-- if (! (yysize <= yysize1 && yysize1 <= YYSTACK_ALLOC_MAXIMUM))
-- return 2;
-- yysize = yysize1;
-- }
-+ yysize1 = yysize + yystrlen (yyformat);
-+ if (! (yysize <= yysize1 && yysize1 <= YYSTACK_ALLOC_MAXIMUM))
-+ return 2;
-+ yysize = yysize1;
-
- if (*yymsg_alloc < yysize)
- {
-@@ -1173,21 +1246,50 @@ yysyntax_error (YYSIZE_T *yymsg_alloc, c
- | Release the memory associated to this symbol. |
- `-----------------------------------------------*/
-
-+/*ARGSUSED*/
-+#if (defined __STDC__ || defined __C99__FUNC__ \
-+ || defined __cplusplus || defined _MSC_VER)
- static void
- yydestruct (const char *yymsg, int yytype, YYSTYPE *yyvaluep, YYLTYPE *yylocationp)
-+#else
-+static void
-+yydestruct (yymsg, yytype, yyvaluep, yylocationp)
-+ const char *yymsg;
-+ int yytype;
-+ YYSTYPE *yyvaluep;
-+ YYLTYPE *yylocationp;
-+#endif
- {
- YYUSE (yyvaluep);
- YYUSE (yylocationp);
-+
- if (!yymsg)
- yymsg = "Deleting";
- YY_SYMBOL_PRINT (yymsg, yytype, yyvaluep, yylocationp);
-
-- YY_IGNORE_MAYBE_UNINITIALIZED_BEGIN
-- YYUSE (yytype);
-- YY_IGNORE_MAYBE_UNINITIALIZED_END
-+ switch (yytype)
-+ {
-+
-+ default:
-+ break;
-+ }
- }
-
-
-+/* Prevent warnings from -Wmissing-prototypes. */
-+#ifdef YYPARSE_PARAM
-+#if defined __STDC__ || defined __cplusplus
-+int yyparse (void *YYPARSE_PARAM);
-+#else
-+int yyparse ();
-+#endif
-+#else /* ! YYPARSE_PARAM */
-+#if defined __STDC__ || defined __cplusplus
-+int yyparse (void);
-+#else
-+int yyparse ();
-+#endif
-+#endif /* ! YYPARSE_PARAM */
-
-
- /* The lookahead symbol. */
-@@ -1195,12 +1297,10 @@ int yychar;
-
- /* The semantic value of the lookahead symbol. */
- YYSTYPE yylval;
-+
- /* Location data for the lookahead symbol. */
--YYLTYPE yylloc
--# if defined YYLTYPE_IS_TRIVIAL && YYLTYPE_IS_TRIVIAL
-- = { 1, 1, 1, 1 }
--# endif
--;
-+YYLTYPE yylloc;
-+
- /* Number of syntax errors so far. */
- int yynerrs;
-
-@@ -1209,19 +1309,38 @@ int yynerrs;
- | yyparse. |
- `----------*/
-
-+#ifdef YYPARSE_PARAM
-+#if (defined __STDC__ || defined __C99__FUNC__ \
-+ || defined __cplusplus || defined _MSC_VER)
-+int
-+yyparse (void *YYPARSE_PARAM)
-+#else
-+int
-+yyparse (YYPARSE_PARAM)
-+ void *YYPARSE_PARAM;
-+#endif
-+#else /* ! YYPARSE_PARAM */
-+#if (defined __STDC__ || defined __C99__FUNC__ \
-+ || defined __cplusplus || defined _MSC_VER)
- int
- yyparse (void)
-+#else
-+int
-+yyparse ()
-+
-+#endif
-+#endif
- {
- int yystate;
- /* Number of tokens to shift before error messages enabled. */
- int yyerrstatus;
-
- /* The stacks and their tools:
-- 'yyss': related to states.
-- 'yyvs': related to semantic values.
-- 'yyls': related to locations.
-+ `yyss': related to states.
-+ `yyvs': related to semantic values.
-+ `yyls': related to locations.
-
-- Refer to the stacks through separate pointers, to allow yyoverflow
-+ Refer to the stacks thru separate pointers, to allow yyoverflow
- to reallocate them elsewhere. */
-
- /* The state stack. */
-@@ -1247,7 +1366,7 @@ yyparse (void)
- int yyn;
- int yyresult;
- /* Lookahead token as an internal (translated) token number. */
-- int yytoken = 0;
-+ int yytoken;
- /* The variables used to return semantic value and location from the
- action routines. */
- YYSTYPE yyval;
-@@ -1266,9 +1385,10 @@ yyparse (void)
- Keep to zero when no symbol should be popped. */
- int yylen = 0;
-
-- yyssp = yyss = yyssa;
-- yyvsp = yyvs = yyvsa;
-- yylsp = yyls = yylsa;
-+ yytoken = 0;
-+ yyss = yyssa;
-+ yyvs = yyvsa;
-+ yyls = yylsa;
- yystacksize = YYINITDEPTH;
-
- YYDPRINTF ((stderr, "Starting parse\n"));
-@@ -1277,7 +1397,21 @@ yyparse (void)
- yyerrstatus = 0;
- yynerrs = 0;
- yychar = YYEMPTY; /* Cause a token to be read. */
-- yylsp[0] = yylloc;
-+
-+ /* Initialize stack pointers.
-+ Waste one element of value and location stack
-+ so that they stay on the same level as the state stack.
-+ The wasted elements are never initialized. */
-+ yyssp = yyss;
-+ yyvsp = yyvs;
-+ yylsp = yyls;
-+
-+#if defined YYLTYPE_IS_TRIVIAL && YYLTYPE_IS_TRIVIAL
-+ /* Initialize the default location before parsing starts. */
-+ yylloc.first_line = yylloc.last_line = 1;
-+ yylloc.first_column = yylloc.last_column = 1;
-+#endif
-+
- goto yysetstate;
-
- /*------------------------------------------------------------.
-@@ -1298,26 +1432,26 @@ yyparse (void)
-
- #ifdef yyoverflow
- {
-- /* Give user a chance to reallocate the stack. Use copies of
-- these so that the &'s don't force the real ones into
-- memory. */
-- YYSTYPE *yyvs1 = yyvs;
-- yytype_int16 *yyss1 = yyss;
-- YYLTYPE *yyls1 = yyls;
--
-- /* Each stack pointer address is followed by the size of the
-- data in use in that stack, in bytes. This used to be a
-- conditional around just the two extra args, but that might
-- be undefined if yyoverflow is a macro. */
-- yyoverflow (YY_("memory exhausted"),
-- &yyss1, yysize * sizeof (*yyssp),
-- &yyvs1, yysize * sizeof (*yyvsp),
-- &yyls1, yysize * sizeof (*yylsp),
-- &yystacksize);
--
-- yyls = yyls1;
-- yyss = yyss1;
-- yyvs = yyvs1;
-+ /* Give user a chance to reallocate the stack. Use copies of
-+ these so that the &'s don't force the real ones into
-+ memory. */
-+ YYSTYPE *yyvs1 = yyvs;
-+ yytype_int16 *yyss1 = yyss;
-+ YYLTYPE *yyls1 = yyls;
-+
-+ /* Each stack pointer address is followed by the size of the
-+ data in use in that stack, in bytes. This used to be a
-+ conditional around just the two extra args, but that might
-+ be undefined if yyoverflow is a macro. */
-+ yyoverflow (YY_("memory exhausted"),
-+ &yyss1, yysize * sizeof (*yyssp),
-+ &yyvs1, yysize * sizeof (*yyvsp),
-+ &yyls1, yysize * sizeof (*yylsp),
-+ &yystacksize);
-+
-+ yyls = yyls1;
-+ yyss = yyss1;
-+ yyvs = yyvs1;
- }
- #else /* no yyoverflow */
- # ifndef YYSTACK_RELOCATE
-@@ -1325,23 +1459,23 @@ yyparse (void)
- # else
- /* Extend the stack our own way. */
- if (YYMAXDEPTH <= yystacksize)
-- goto yyexhaustedlab;
-+ goto yyexhaustedlab;
- yystacksize *= 2;
- if (YYMAXDEPTH < yystacksize)
-- yystacksize = YYMAXDEPTH;
-+ yystacksize = YYMAXDEPTH;
-
- {
-- yytype_int16 *yyss1 = yyss;
-- union yyalloc *yyptr =
-- (union yyalloc *) YYSTACK_ALLOC (YYSTACK_BYTES (yystacksize));
-- if (! yyptr)
-- goto yyexhaustedlab;
-- YYSTACK_RELOCATE (yyss_alloc, yyss);
-- YYSTACK_RELOCATE (yyvs_alloc, yyvs);
-- YYSTACK_RELOCATE (yyls_alloc, yyls);
-+ yytype_int16 *yyss1 = yyss;
-+ union yyalloc *yyptr =
-+ (union yyalloc *) YYSTACK_ALLOC (YYSTACK_BYTES (yystacksize));
-+ if (! yyptr)
-+ goto yyexhaustedlab;
-+ YYSTACK_RELOCATE (yyss_alloc, yyss);
-+ YYSTACK_RELOCATE (yyvs_alloc, yyvs);
-+ YYSTACK_RELOCATE (yyls_alloc, yyls);
- # undef YYSTACK_RELOCATE
-- if (yyss1 != yyssa)
-- YYSTACK_FREE (yyss1);
-+ if (yyss1 != yyssa)
-+ YYSTACK_FREE (yyss1);
- }
- # endif
- #endif /* no yyoverflow */
-@@ -1351,10 +1485,10 @@ yyparse (void)
- yylsp = yyls + yysize - 1;
-
- YYDPRINTF ((stderr, "Stack size increased to %lu\n",
-- (unsigned long int) yystacksize));
-+ (unsigned long int) yystacksize));
-
- if (yyss + yystacksize - 1 <= yyssp)
-- YYABORT;
-+ YYABORT;
- }
-
- YYDPRINTF ((stderr, "Entering state %d\n", yystate));
-@@ -1383,7 +1517,7 @@ yybackup:
- if (yychar == YYEMPTY)
- {
- YYDPRINTF ((stderr, "Reading a token: "));
-- yychar = yylex ();
-+ yychar = YYLEX;
- }
-
- if (yychar <= YYEOF)
-@@ -1423,9 +1557,7 @@ yybackup:
- yychar = YYEMPTY;
-
- yystate = yyn;
-- YY_IGNORE_MAYBE_UNINITIALIZED_BEGIN
- *++yyvsp = yylval;
-- YY_IGNORE_MAYBE_UNINITIALIZED_END
- *++yylsp = yylloc;
- goto yynewstate;
-
-@@ -1448,7 +1580,7 @@ yyreduce:
- yylen = yyr2[yyn];
-
- /* If YYLEN is nonzero, implement the default value of the action:
-- '$$ = $1'.
-+ `$$ = $1'.
-
- Otherwise, the following line sets YYVAL to garbage.
- This behavior is undocumented and Bison
-@@ -1463,273 +1595,322 @@ yyreduce:
- switch (yyn)
- {
- case 2:
--#line 105 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 109 "dtc-parser.y"
- {
-- the_boot_info = build_boot_info((yyvsp[-1].re), (yyvsp[0].node),
-- guess_boot_cpuid((yyvsp[0].node)));
-+ (yyvsp[(5) - (5)].node)->is_plugin = (yyvsp[(3) - (5)].is_plugin);
-+ (yyvsp[(5) - (5)].node)->is_root = 1;
-+ the_boot_info = build_boot_info((yyvsp[(4) - (5)].re), (yyvsp[(5) - (5)].node),
-+ guess_boot_cpuid((yyvsp[(5) - (5)].node)));
- }
--#line 1472 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 3:
--#line 113 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 119 "dtc-parser.y"
- {
-- (yyval.re) = NULL;
-+ (yyval.is_plugin) = 0;
- }
--#line 1480 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 4:
--#line 117 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 123 "dtc-parser.y"
- {
-- (yyval.re) = chain_reserve_entry((yyvsp[-1].re), (yyvsp[0].re));
-+ (yyval.is_plugin) = 1;
- }
--#line 1488 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 5:
--#line 124 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 130 "dtc-parser.y"
- {
-- (yyval.re) = build_reserve_entry((yyvsp[-2].integer), (yyvsp[-1].integer));
-+ (yyval.re) = NULL;
- }
--#line 1496 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 6:
--#line 128 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 134 "dtc-parser.y"
- {
-- add_label(&(yyvsp[0].re)->labels, (yyvsp[-1].labelref));
-- (yyval.re) = (yyvsp[0].re);
-+ (yyval.re) = chain_reserve_entry((yyvsp[(1) - (2)].re), (yyvsp[(2) - (2)].re));
- }
--#line 1505 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 7:
--#line 136 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 141 "dtc-parser.y"
- {
-- (yyval.node) = name_node((yyvsp[0].node), "");
-+ (yyval.re) = build_reserve_entry((yyvsp[(2) - (4)].integer), (yyvsp[(3) - (4)].integer));
- }
--#line 1513 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 8:
--#line 140 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 145 "dtc-parser.y"
- {
-- (yyval.node) = merge_nodes((yyvsp[-2].node), (yyvsp[0].node));
-+ add_label(&(yyvsp[(2) - (2)].re)->labels, (yyvsp[(1) - (2)].labelref));
-+ (yyval.re) = (yyvsp[(2) - (2)].re);
- }
--#line 1521 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 9:
--#line 145 "dtc-parser.y" /* yacc.c:1646 */
-- {
-- struct node *target = get_node_by_ref((yyvsp[-3].node), (yyvsp[-1].labelref));
-
-- add_label(&target->labels, (yyvsp[-2].labelref));
-- if (target)
-- merge_nodes(target, (yyvsp[0].node));
-- else
-- ERROR(&(yylsp[-1]), "Label or path %s not found", (yyvsp[-1].labelref));
-- (yyval.node) = (yyvsp[-3].node);
-+/* Line 1806 of yacc.c */
-+#line 153 "dtc-parser.y"
-+ {
-+ (yyval.node) = name_node((yyvsp[(2) - (2)].node), "");
- }
--#line 1536 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 10:
--#line 156 "dtc-parser.y" /* yacc.c:1646 */
-- {
-- struct node *target = get_node_by_ref((yyvsp[-2].node), (yyvsp[-1].labelref));
-
-- if (target)
-- merge_nodes(target, (yyvsp[0].node));
-- else
-- ERROR(&(yylsp[-1]), "Label or path %s not found", (yyvsp[-1].labelref));
-- (yyval.node) = (yyvsp[-2].node);
-+/* Line 1806 of yacc.c */
-+#line 157 "dtc-parser.y"
-+ {
-+ (yyval.node) = merge_nodes((yyvsp[(1) - (3)].node), (yyvsp[(3) - (3)].node));
- }
--#line 1550 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 11:
--#line 166 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 162 "dtc-parser.y"
- {
-- struct node *target = get_node_by_ref((yyvsp[-3].node), (yyvsp[-1].labelref));
-+ struct node *target = get_node_by_ref((yyvsp[(1) - (4)].node), (yyvsp[(3) - (4)].labelref));
-
-+ add_label(&target->labels, (yyvsp[(2) - (4)].labelref));
- if (target)
-- delete_node(target);
-+ merge_nodes(target, (yyvsp[(4) - (4)].node));
- else
-- ERROR(&(yylsp[-1]), "Label or path %s not found", (yyvsp[-1].labelref));
--
--
-- (yyval.node) = (yyvsp[-3].node);
-+ ERROR(&(yylsp[(3) - (4)]), "Label or path %s not found", (yyvsp[(3) - (4)].labelref));
-+ (yyval.node) = (yyvsp[(1) - (4)].node);
- }
--#line 1566 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 12:
--#line 181 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 173 "dtc-parser.y"
- {
-- (yyval.node) = build_node((yyvsp[-3].proplist), (yyvsp[-2].nodelist));
-+ struct node *target = get_node_by_ref((yyvsp[(1) - (3)].node), (yyvsp[(2) - (3)].labelref));
-+
-+ if (target)
-+ merge_nodes(target, (yyvsp[(3) - (3)].node));
-+ else
-+ ERROR(&(yylsp[(2) - (3)]), "Label or path %s not found", (yyvsp[(2) - (3)].labelref));
-+ (yyval.node) = (yyvsp[(1) - (3)].node);
- }
--#line 1574 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 13:
--#line 188 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 183 "dtc-parser.y"
- {
-- (yyval.proplist) = NULL;
-+ struct node *target = get_node_by_ref((yyvsp[(1) - (4)].node), (yyvsp[(3) - (4)].labelref));
-+
-+ if (target)
-+ delete_node(target);
-+ else
-+ ERROR(&(yylsp[(3) - (4)]), "Label or path %s not found", (yyvsp[(3) - (4)].labelref));
-+
-+
-+ (yyval.node) = (yyvsp[(1) - (4)].node);
- }
--#line 1582 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 14:
--#line 192 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 198 "dtc-parser.y"
- {
-- (yyval.proplist) = chain_property((yyvsp[0].prop), (yyvsp[-1].proplist));
-+ (yyval.node) = build_node((yyvsp[(2) - (5)].proplist), (yyvsp[(3) - (5)].nodelist));
- }
--#line 1590 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 15:
--#line 199 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 205 "dtc-parser.y"
- {
-- (yyval.prop) = build_property((yyvsp[-3].propnodename), (yyvsp[-1].data));
-+ (yyval.proplist) = NULL;
- }
--#line 1598 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 16:
--#line 203 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 209 "dtc-parser.y"
- {
-- (yyval.prop) = build_property((yyvsp[-1].propnodename), empty_data);
-+ (yyval.proplist) = chain_property((yyvsp[(2) - (2)].prop), (yyvsp[(1) - (2)].proplist));
- }
--#line 1606 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 17:
--#line 207 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 216 "dtc-parser.y"
- {
-- (yyval.prop) = build_property_delete((yyvsp[-1].propnodename));
-+ (yyval.prop) = build_property((yyvsp[(1) - (4)].propnodename), (yyvsp[(3) - (4)].data));
- }
--#line 1614 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 18:
--#line 211 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 220 "dtc-parser.y"
- {
-- add_label(&(yyvsp[0].prop)->labels, (yyvsp[-1].labelref));
-- (yyval.prop) = (yyvsp[0].prop);
-+ (yyval.prop) = build_property((yyvsp[(1) - (2)].propnodename), empty_data);
- }
--#line 1623 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 19:
--#line 219 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 224 "dtc-parser.y"
- {
-- (yyval.data) = data_merge((yyvsp[-1].data), (yyvsp[0].data));
-+ (yyval.prop) = build_property_delete((yyvsp[(2) - (3)].propnodename));
- }
--#line 1631 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 20:
--#line 223 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 228 "dtc-parser.y"
- {
-- (yyval.data) = data_merge((yyvsp[-2].data), (yyvsp[-1].array).data);
-+ add_label(&(yyvsp[(2) - (2)].prop)->labels, (yyvsp[(1) - (2)].labelref));
-+ (yyval.prop) = (yyvsp[(2) - (2)].prop);
- }
--#line 1639 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 21:
--#line 227 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 236 "dtc-parser.y"
- {
-- (yyval.data) = data_merge((yyvsp[-3].data), (yyvsp[-1].data));
-+ (yyval.data) = data_merge((yyvsp[(1) - (2)].data), (yyvsp[(2) - (2)].data));
- }
--#line 1647 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 22:
--#line 231 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 240 "dtc-parser.y"
- {
-- (yyval.data) = data_add_marker((yyvsp[-1].data), REF_PATH, (yyvsp[0].labelref));
-+ (yyval.data) = data_merge((yyvsp[(1) - (3)].data), (yyvsp[(2) - (3)].array).data);
- }
--#line 1655 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 23:
--#line 235 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 244 "dtc-parser.y"
-+ {
-+ (yyval.data) = data_merge((yyvsp[(1) - (4)].data), (yyvsp[(3) - (4)].data));
-+ }
-+ break;
-+
-+ case 24:
-+
-+/* Line 1806 of yacc.c */
-+#line 248 "dtc-parser.y"
-+ {
-+ (yyval.data) = data_add_marker((yyvsp[(1) - (2)].data), REF_PATH, (yyvsp[(2) - (2)].labelref));
-+ }
-+ break;
-+
-+ case 25:
-+
-+/* Line 1806 of yacc.c */
-+#line 252 "dtc-parser.y"
- {
-- FILE *f = srcfile_relative_open((yyvsp[-5].data).val, NULL);
-+ FILE *f = srcfile_relative_open((yyvsp[(4) - (9)].data).val, NULL);
- struct data d;
-
-- if ((yyvsp[-3].integer) != 0)
-- if (fseek(f, (yyvsp[-3].integer), SEEK_SET) != 0)
-+ if ((yyvsp[(6) - (9)].integer) != 0)
-+ if (fseek(f, (yyvsp[(6) - (9)].integer), SEEK_SET) != 0)
- die("Couldn't seek to offset %llu in \"%s\": %s",
-- (unsigned long long)(yyvsp[-3].integer), (yyvsp[-5].data).val,
-+ (unsigned long long)(yyvsp[(6) - (9)].integer), (yyvsp[(4) - (9)].data).val,
- strerror(errno));
-
-- d = data_copy_file(f, (yyvsp[-1].integer));
-+ d = data_copy_file(f, (yyvsp[(8) - (9)].integer));
-
-- (yyval.data) = data_merge((yyvsp[-8].data), d);
-+ (yyval.data) = data_merge((yyvsp[(1) - (9)].data), d);
- fclose(f);
- }
--#line 1675 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 24:
--#line 251 "dtc-parser.y" /* yacc.c:1646 */
-+ case 26:
-+
-+/* Line 1806 of yacc.c */
-+#line 268 "dtc-parser.y"
- {
-- FILE *f = srcfile_relative_open((yyvsp[-1].data).val, NULL);
-+ FILE *f = srcfile_relative_open((yyvsp[(4) - (5)].data).val, NULL);
- struct data d = empty_data;
-
- d = data_copy_file(f, -1);
-
-- (yyval.data) = data_merge((yyvsp[-4].data), d);
-+ (yyval.data) = data_merge((yyvsp[(1) - (5)].data), d);
- fclose(f);
- }
--#line 1689 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 25:
--#line 261 "dtc-parser.y" /* yacc.c:1646 */
-+ case 27:
-+
-+/* Line 1806 of yacc.c */
-+#line 278 "dtc-parser.y"
- {
-- (yyval.data) = data_add_marker((yyvsp[-1].data), LABEL, (yyvsp[0].labelref));
-+ (yyval.data) = data_add_marker((yyvsp[(1) - (2)].data), LABEL, (yyvsp[(2) - (2)].labelref));
- }
--#line 1697 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 26:
--#line 268 "dtc-parser.y" /* yacc.c:1646 */
-+ case 28:
-+
-+/* Line 1806 of yacc.c */
-+#line 285 "dtc-parser.y"
- {
- (yyval.data) = empty_data;
- }
--#line 1705 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 27:
--#line 272 "dtc-parser.y" /* yacc.c:1646 */
-+ case 29:
-+
-+/* Line 1806 of yacc.c */
-+#line 289 "dtc-parser.y"
- {
-- (yyval.data) = (yyvsp[-1].data);
-+ (yyval.data) = (yyvsp[(1) - (2)].data);
- }
--#line 1713 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 28:
--#line 276 "dtc-parser.y" /* yacc.c:1646 */
-+ case 30:
-+
-+/* Line 1806 of yacc.c */
-+#line 293 "dtc-parser.y"
- {
-- (yyval.data) = data_add_marker((yyvsp[-1].data), LABEL, (yyvsp[0].labelref));
-+ (yyval.data) = data_add_marker((yyvsp[(1) - (2)].data), LABEL, (yyvsp[(2) - (2)].labelref));
- }
--#line 1721 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 29:
--#line 283 "dtc-parser.y" /* yacc.c:1646 */
-+ case 31:
-+
-+/* Line 1806 of yacc.c */
-+#line 300 "dtc-parser.y"
- {
- unsigned long long bits;
-
-- bits = (yyvsp[-1].integer);
-+ bits = (yyvsp[(2) - (3)].integer);
-
- if ((bits != 8) && (bits != 16) &&
- (bits != 32) && (bits != 64)) {
-- ERROR(&(yylsp[-1]), "Array elements must be"
-+ ERROR(&(yylsp[(2) - (3)]), "Array elements must be"
- " 8, 16, 32 or 64-bits");
- bits = 32;
- }
-@@ -1737,23 +1918,25 @@ yyreduce:
- (yyval.array).data = empty_data;
- (yyval.array).bits = bits;
- }
--#line 1741 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 30:
--#line 299 "dtc-parser.y" /* yacc.c:1646 */
-+ case 32:
-+
-+/* Line 1806 of yacc.c */
-+#line 316 "dtc-parser.y"
- {
- (yyval.array).data = empty_data;
- (yyval.array).bits = 32;
- }
--#line 1750 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 31:
--#line 304 "dtc-parser.y" /* yacc.c:1646 */
-+ case 33:
-+
-+/* Line 1806 of yacc.c */
-+#line 321 "dtc-parser.y"
- {
-- if ((yyvsp[-1].array).bits < 64) {
-- uint64_t mask = (1ULL << (yyvsp[-1].array).bits) - 1;
-+ if ((yyvsp[(1) - (2)].array).bits < 64) {
-+ uint64_t mask = (1ULL << (yyvsp[(1) - (2)].array).bits) - 1;
- /*
- * Bits above mask must either be all zero
- * (positive within range of mask) or all one
-@@ -1762,258 +1945,293 @@ yyreduce:
- * within the mask to one (i.e. | in the
- * mask), all bits are one.
- */
-- if (((yyvsp[0].integer) > mask) && (((yyvsp[0].integer) | mask) != -1ULL))
-- ERROR(&(yylsp[0]), "Value out of range for"
-- " %d-bit array element", (yyvsp[-1].array).bits);
-+ if (((yyvsp[(2) - (2)].integer) > mask) && (((yyvsp[(2) - (2)].integer) | mask) != -1ULL))
-+ ERROR(&(yylsp[(2) - (2)]), "Value out of range for"
-+ " %d-bit array element", (yyvsp[(1) - (2)].array).bits);
- }
-
-- (yyval.array).data = data_append_integer((yyvsp[-1].array).data, (yyvsp[0].integer), (yyvsp[-1].array).bits);
-+ (yyval.array).data = data_append_integer((yyvsp[(1) - (2)].array).data, (yyvsp[(2) - (2)].integer), (yyvsp[(1) - (2)].array).bits);
- }
--#line 1773 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 32:
--#line 323 "dtc-parser.y" /* yacc.c:1646 */
-+ case 34:
-+
-+/* Line 1806 of yacc.c */
-+#line 340 "dtc-parser.y"
- {
-- uint64_t val = ~0ULL >> (64 - (yyvsp[-1].array).bits);
-+ uint64_t val = ~0ULL >> (64 - (yyvsp[(1) - (2)].array).bits);
-
-- if ((yyvsp[-1].array).bits == 32)
-- (yyvsp[-1].array).data = data_add_marker((yyvsp[-1].array).data,
-+ if ((yyvsp[(1) - (2)].array).bits == 32)
-+ (yyvsp[(1) - (2)].array).data = data_add_marker((yyvsp[(1) - (2)].array).data,
- REF_PHANDLE,
-- (yyvsp[0].labelref));
-+ (yyvsp[(2) - (2)].labelref));
- else
-- ERROR(&(yylsp[0]), "References are only allowed in "
-+ ERROR(&(yylsp[(2) - (2)]), "References are only allowed in "
- "arrays with 32-bit elements.");
-
-- (yyval.array).data = data_append_integer((yyvsp[-1].array).data, val, (yyvsp[-1].array).bits);
-+ (yyval.array).data = data_append_integer((yyvsp[(1) - (2)].array).data, val, (yyvsp[(1) - (2)].array).bits);
- }
--#line 1791 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 33:
--#line 337 "dtc-parser.y" /* yacc.c:1646 */
-+ case 35:
-+
-+/* Line 1806 of yacc.c */
-+#line 354 "dtc-parser.y"
- {
-- (yyval.array).data = data_add_marker((yyvsp[-1].array).data, LABEL, (yyvsp[0].labelref));
-+ (yyval.array).data = data_add_marker((yyvsp[(1) - (2)].array).data, LABEL, (yyvsp[(2) - (2)].labelref));
- }
--#line 1799 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 36:
--#line 346 "dtc-parser.y" /* yacc.c:1646 */
-+ case 38:
-+
-+/* Line 1806 of yacc.c */
-+#line 363 "dtc-parser.y"
- {
-- (yyval.integer) = (yyvsp[-1].integer);
-+ (yyval.integer) = (yyvsp[(2) - (3)].integer);
- }
--#line 1807 "dtc-parser.tab.c" /* yacc.c:1646 */
-- break;
--
-- case 39:
--#line 357 "dtc-parser.y" /* yacc.c:1646 */
-- { (yyval.integer) = (yyvsp[-4].integer) ? (yyvsp[-2].integer) : (yyvsp[0].integer); }
--#line 1813 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 41:
--#line 362 "dtc-parser.y" /* yacc.c:1646 */
-- { (yyval.integer) = (yyvsp[-2].integer) || (yyvsp[0].integer); }
--#line 1819 "dtc-parser.tab.c" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 374 "dtc-parser.y"
-+ { (yyval.integer) = (yyvsp[(1) - (5)].integer) ? (yyvsp[(3) - (5)].integer) : (yyvsp[(5) - (5)].integer); }
- break;
-
- case 43:
--#line 367 "dtc-parser.y" /* yacc.c:1646 */
-- { (yyval.integer) = (yyvsp[-2].integer) && (yyvsp[0].integer); }
--#line 1825 "dtc-parser.tab.c" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 379 "dtc-parser.y"
-+ { (yyval.integer) = (yyvsp[(1) - (3)].integer) || (yyvsp[(3) - (3)].integer); }
- break;
-
- case 45:
--#line 372 "dtc-parser.y" /* yacc.c:1646 */
-- { (yyval.integer) = (yyvsp[-2].integer) | (yyvsp[0].integer); }
--#line 1831 "dtc-parser.tab.c" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 384 "dtc-parser.y"
-+ { (yyval.integer) = (yyvsp[(1) - (3)].integer) && (yyvsp[(3) - (3)].integer); }
- break;
-
- case 47:
--#line 377 "dtc-parser.y" /* yacc.c:1646 */
-- { (yyval.integer) = (yyvsp[-2].integer) ^ (yyvsp[0].integer); }
--#line 1837 "dtc-parser.tab.c" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 389 "dtc-parser.y"
-+ { (yyval.integer) = (yyvsp[(1) - (3)].integer) | (yyvsp[(3) - (3)].integer); }
- break;
-
- case 49:
--#line 382 "dtc-parser.y" /* yacc.c:1646 */
-- { (yyval.integer) = (yyvsp[-2].integer) & (yyvsp[0].integer); }
--#line 1843 "dtc-parser.tab.c" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 394 "dtc-parser.y"
-+ { (yyval.integer) = (yyvsp[(1) - (3)].integer) ^ (yyvsp[(3) - (3)].integer); }
- break;
-
- case 51:
--#line 387 "dtc-parser.y" /* yacc.c:1646 */
-- { (yyval.integer) = (yyvsp[-2].integer) == (yyvsp[0].integer); }
--#line 1849 "dtc-parser.tab.c" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 399 "dtc-parser.y"
-+ { (yyval.integer) = (yyvsp[(1) - (3)].integer) & (yyvsp[(3) - (3)].integer); }
- break;
-
-- case 52:
--#line 388 "dtc-parser.y" /* yacc.c:1646 */
-- { (yyval.integer) = (yyvsp[-2].integer) != (yyvsp[0].integer); }
--#line 1855 "dtc-parser.tab.c" /* yacc.c:1646 */
-+ case 53:
-+
-+/* Line 1806 of yacc.c */
-+#line 404 "dtc-parser.y"
-+ { (yyval.integer) = (yyvsp[(1) - (3)].integer) == (yyvsp[(3) - (3)].integer); }
- break;
-
- case 54:
--#line 393 "dtc-parser.y" /* yacc.c:1646 */
-- { (yyval.integer) = (yyvsp[-2].integer) < (yyvsp[0].integer); }
--#line 1861 "dtc-parser.tab.c" /* yacc.c:1646 */
-- break;
-
-- case 55:
--#line 394 "dtc-parser.y" /* yacc.c:1646 */
-- { (yyval.integer) = (yyvsp[-2].integer) > (yyvsp[0].integer); }
--#line 1867 "dtc-parser.tab.c" /* yacc.c:1646 */
-+/* Line 1806 of yacc.c */
-+#line 405 "dtc-parser.y"
-+ { (yyval.integer) = (yyvsp[(1) - (3)].integer) != (yyvsp[(3) - (3)].integer); }
- break;
-
- case 56:
--#line 395 "dtc-parser.y" /* yacc.c:1646 */
-- { (yyval.integer) = (yyvsp[-2].integer) <= (yyvsp[0].integer); }
--#line 1873 "dtc-parser.tab.c" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 410 "dtc-parser.y"
-+ { (yyval.integer) = (yyvsp[(1) - (3)].integer) < (yyvsp[(3) - (3)].integer); }
- break;
-
- case 57:
--#line 396 "dtc-parser.y" /* yacc.c:1646 */
-- { (yyval.integer) = (yyvsp[-2].integer) >= (yyvsp[0].integer); }
--#line 1879 "dtc-parser.tab.c" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 411 "dtc-parser.y"
-+ { (yyval.integer) = (yyvsp[(1) - (3)].integer) > (yyvsp[(3) - (3)].integer); }
- break;
-
- case 58:
--#line 400 "dtc-parser.y" /* yacc.c:1646 */
-- { (yyval.integer) = (yyvsp[-2].integer) << (yyvsp[0].integer); }
--#line 1885 "dtc-parser.tab.c" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 412 "dtc-parser.y"
-+ { (yyval.integer) = (yyvsp[(1) - (3)].integer) <= (yyvsp[(3) - (3)].integer); }
- break;
-
- case 59:
--#line 401 "dtc-parser.y" /* yacc.c:1646 */
-- { (yyval.integer) = (yyvsp[-2].integer) >> (yyvsp[0].integer); }
--#line 1891 "dtc-parser.tab.c" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 413 "dtc-parser.y"
-+ { (yyval.integer) = (yyvsp[(1) - (3)].integer) >= (yyvsp[(3) - (3)].integer); }
-+ break;
-+
-+ case 60:
-+
-+/* Line 1806 of yacc.c */
-+#line 417 "dtc-parser.y"
-+ { (yyval.integer) = (yyvsp[(1) - (3)].integer) << (yyvsp[(3) - (3)].integer); }
- break;
-
- case 61:
--#line 406 "dtc-parser.y" /* yacc.c:1646 */
-- { (yyval.integer) = (yyvsp[-2].integer) + (yyvsp[0].integer); }
--#line 1897 "dtc-parser.tab.c" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 418 "dtc-parser.y"
-+ { (yyval.integer) = (yyvsp[(1) - (3)].integer) >> (yyvsp[(3) - (3)].integer); }
- break;
-
-- case 62:
--#line 407 "dtc-parser.y" /* yacc.c:1646 */
-- { (yyval.integer) = (yyvsp[-2].integer) - (yyvsp[0].integer); }
--#line 1903 "dtc-parser.tab.c" /* yacc.c:1646 */
-+ case 63:
-+
-+/* Line 1806 of yacc.c */
-+#line 423 "dtc-parser.y"
-+ { (yyval.integer) = (yyvsp[(1) - (3)].integer) + (yyvsp[(3) - (3)].integer); }
- break;
-
- case 64:
--#line 412 "dtc-parser.y" /* yacc.c:1646 */
-- { (yyval.integer) = (yyvsp[-2].integer) * (yyvsp[0].integer); }
--#line 1909 "dtc-parser.tab.c" /* yacc.c:1646 */
-- break;
-
-- case 65:
--#line 413 "dtc-parser.y" /* yacc.c:1646 */
-- { (yyval.integer) = (yyvsp[-2].integer) / (yyvsp[0].integer); }
--#line 1915 "dtc-parser.tab.c" /* yacc.c:1646 */
-+/* Line 1806 of yacc.c */
-+#line 424 "dtc-parser.y"
-+ { (yyval.integer) = (yyvsp[(1) - (3)].integer) - (yyvsp[(3) - (3)].integer); }
- break;
-
- case 66:
--#line 414 "dtc-parser.y" /* yacc.c:1646 */
-- { (yyval.integer) = (yyvsp[-2].integer) % (yyvsp[0].integer); }
--#line 1921 "dtc-parser.tab.c" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 429 "dtc-parser.y"
-+ { (yyval.integer) = (yyvsp[(1) - (3)].integer) * (yyvsp[(3) - (3)].integer); }
- break;
-
-- case 69:
--#line 420 "dtc-parser.y" /* yacc.c:1646 */
-- { (yyval.integer) = -(yyvsp[0].integer); }
--#line 1927 "dtc-parser.tab.c" /* yacc.c:1646 */
-+ case 67:
-+
-+/* Line 1806 of yacc.c */
-+#line 430 "dtc-parser.y"
-+ { (yyval.integer) = (yyvsp[(1) - (3)].integer) / (yyvsp[(3) - (3)].integer); }
- break;
-
-- case 70:
--#line 421 "dtc-parser.y" /* yacc.c:1646 */
-- { (yyval.integer) = ~(yyvsp[0].integer); }
--#line 1933 "dtc-parser.tab.c" /* yacc.c:1646 */
-+ case 68:
-+
-+/* Line 1806 of yacc.c */
-+#line 431 "dtc-parser.y"
-+ { (yyval.integer) = (yyvsp[(1) - (3)].integer) % (yyvsp[(3) - (3)].integer); }
- break;
-
- case 71:
--#line 422 "dtc-parser.y" /* yacc.c:1646 */
-- { (yyval.integer) = !(yyvsp[0].integer); }
--#line 1939 "dtc-parser.tab.c" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 437 "dtc-parser.y"
-+ { (yyval.integer) = -(yyvsp[(2) - (2)].integer); }
- break;
-
- case 72:
--#line 427 "dtc-parser.y" /* yacc.c:1646 */
-- {
-- (yyval.data) = empty_data;
-- }
--#line 1947 "dtc-parser.tab.c" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 438 "dtc-parser.y"
-+ { (yyval.integer) = ~(yyvsp[(2) - (2)].integer); }
- break;
-
- case 73:
--#line 431 "dtc-parser.y" /* yacc.c:1646 */
-- {
-- (yyval.data) = data_append_byte((yyvsp[-1].data), (yyvsp[0].byte));
-- }
--#line 1955 "dtc-parser.tab.c" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 439 "dtc-parser.y"
-+ { (yyval.integer) = !(yyvsp[(2) - (2)].integer); }
- break;
-
- case 74:
--#line 435 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 444 "dtc-parser.y"
- {
-- (yyval.data) = data_add_marker((yyvsp[-1].data), LABEL, (yyvsp[0].labelref));
-+ (yyval.data) = empty_data;
- }
--#line 1963 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 75:
--#line 442 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 448 "dtc-parser.y"
- {
-- (yyval.nodelist) = NULL;
-+ (yyval.data) = data_append_byte((yyvsp[(1) - (2)].data), (yyvsp[(2) - (2)].byte));
- }
--#line 1971 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 76:
--#line 446 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 452 "dtc-parser.y"
- {
-- (yyval.nodelist) = chain_node((yyvsp[-1].node), (yyvsp[0].nodelist));
-+ (yyval.data) = data_add_marker((yyvsp[(1) - (2)].data), LABEL, (yyvsp[(2) - (2)].labelref));
- }
--#line 1979 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 77:
--#line 450 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 459 "dtc-parser.y"
- {
-- ERROR(&(yylsp[0]), "Properties must precede subnodes");
-- YYERROR;
-+ (yyval.nodelist) = NULL;
- }
--#line 1988 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 78:
--#line 458 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 463 "dtc-parser.y"
- {
-- (yyval.node) = name_node((yyvsp[0].node), (yyvsp[-1].propnodename));
-+ (yyval.nodelist) = chain_node((yyvsp[(1) - (2)].node), (yyvsp[(2) - (2)].nodelist));
- }
--#line 1996 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 79:
--#line 462 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 467 "dtc-parser.y"
- {
-- (yyval.node) = name_node(build_node_delete(), (yyvsp[-1].propnodename));
-+ ERROR(&(yylsp[(2) - (2)]), "Properties must precede subnodes");
-+ YYERROR;
- }
--#line 2004 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 80:
--#line 466 "dtc-parser.y" /* yacc.c:1646 */
-+
-+/* Line 1806 of yacc.c */
-+#line 475 "dtc-parser.y"
- {
-- add_label(&(yyvsp[0].node)->labels, (yyvsp[-1].labelref));
-- (yyval.node) = (yyvsp[0].node);
-+ (yyval.node) = name_node((yyvsp[(2) - (2)].node), (yyvsp[(1) - (2)].propnodename));
- }
--#line 2013 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-+ case 81:
-
--#line 2017 "dtc-parser.tab.c" /* yacc.c:1646 */
-+/* Line 1806 of yacc.c */
-+#line 479 "dtc-parser.y"
-+ {
-+ (yyval.node) = name_node(build_node_delete(), (yyvsp[(2) - (3)].propnodename));
-+ }
-+ break;
-+
-+ case 82:
-+
-+/* Line 1806 of yacc.c */
-+#line 483 "dtc-parser.y"
-+ {
-+ add_label(&(yyvsp[(2) - (2)].node)->labels, (yyvsp[(1) - (2)].labelref));
-+ (yyval.node) = (yyvsp[(2) - (2)].node);
-+ }
-+ break;
-+
-+
-+
-+/* Line 1806 of yacc.c */
-+#line 2235 "dtc-parser.tab.c"
- default: break;
- }
- /* User semantic actions sometimes alter yychar, and that requires
-@@ -2036,7 +2254,7 @@ yyreduce:
- *++yyvsp = yyval;
- *++yylsp = yyloc;
-
-- /* Now 'shift' the result of the reduction. Determine what state
-+ /* Now `shift' the result of the reduction. Determine what state
- that goes to, based on the state we popped back to and the rule
- number reduced by. */
-
-@@ -2051,9 +2269,9 @@ yyreduce:
- goto yynewstate;
-
-
--/*--------------------------------------.
--| yyerrlab -- here on detecting error. |
--`--------------------------------------*/
-+/*------------------------------------.
-+| yyerrlab -- here on detecting error |
-+`------------------------------------*/
- yyerrlab:
- /* Make sure we have latest lookahead translation. See comments at
- user semantic actions for why this is necessary. */
-@@ -2104,20 +2322,20 @@ yyerrlab:
- if (yyerrstatus == 3)
- {
- /* If just tried and failed to reuse lookahead token after an
-- error, discard it. */
-+ error, discard it. */
-
- if (yychar <= YYEOF)
-- {
-- /* Return failure if at end of input. */
-- if (yychar == YYEOF)
-- YYABORT;
-- }
-+ {
-+ /* Return failure if at end of input. */
-+ if (yychar == YYEOF)
-+ YYABORT;
-+ }
- else
-- {
-- yydestruct ("Error: discarding",
-- yytoken, &yylval, &yylloc);
-- yychar = YYEMPTY;
-- }
-+ {
-+ yydestruct ("Error: discarding",
-+ yytoken, &yylval, &yylloc);
-+ yychar = YYEMPTY;
-+ }
- }
-
- /* Else will try to reuse lookahead token after shifting the error
-@@ -2137,7 +2355,7 @@ yyerrorlab:
- goto yyerrorlab;
-
- yyerror_range[1] = yylsp[1-yylen];
-- /* Do not reclaim the symbols of the rule whose action triggered
-+ /* Do not reclaim the symbols of the rule which action triggered
- this YYERROR. */
- YYPOPSTACK (yylen);
- yylen = 0;
-@@ -2150,37 +2368,35 @@ yyerrorlab:
- | yyerrlab1 -- common code for both syntax error and YYERROR. |
- `-------------------------------------------------------------*/
- yyerrlab1:
-- yyerrstatus = 3; /* Each real token shifted decrements this. */
-+ yyerrstatus = 3; /* Each real token shifted decrements this. */
-
- for (;;)
- {
- yyn = yypact[yystate];
- if (!yypact_value_is_default (yyn))
-- {
-- yyn += YYTERROR;
-- if (0 <= yyn && yyn <= YYLAST && yycheck[yyn] == YYTERROR)
-- {
-- yyn = yytable[yyn];
-- if (0 < yyn)
-- break;
-- }
-- }
-+ {
-+ yyn += YYTERROR;
-+ if (0 <= yyn && yyn <= YYLAST && yycheck[yyn] == YYTERROR)
-+ {
-+ yyn = yytable[yyn];
-+ if (0 < yyn)
-+ break;
-+ }
-+ }
-
- /* Pop the current state because it cannot handle the error token. */
- if (yyssp == yyss)
-- YYABORT;
-+ YYABORT;
-
- yyerror_range[1] = *yylsp;
- yydestruct ("Error: popping",
-- yystos[yystate], yyvsp, yylsp);
-+ yystos[yystate], yyvsp, yylsp);
- YYPOPSTACK (1);
- yystate = *yyssp;
- YY_STACK_PRINT (yyss, yyssp);
- }
-
-- YY_IGNORE_MAYBE_UNINITIALIZED_BEGIN
- *++yyvsp = yylval;
-- YY_IGNORE_MAYBE_UNINITIALIZED_END
-
- yyerror_range[2] = yylloc;
- /* Using YYLLOC is tempting, but would change the location of
-@@ -2209,7 +2425,7 @@ yyabortlab:
- yyresult = 1;
- goto yyreturn;
-
--#if !defined yyoverflow || YYERROR_VERBOSE
-+#if !defined(yyoverflow) || YYERROR_VERBOSE
- /*-------------------------------------------------.
- | yyexhaustedlab -- memory exhaustion comes here. |
- `-------------------------------------------------*/
-@@ -2228,14 +2444,14 @@ yyreturn:
- yydestruct ("Cleanup: discarding lookahead",
- yytoken, &yylval, &yylloc);
- }
-- /* Do not reclaim the symbols of the rule whose action triggered
-+ /* Do not reclaim the symbols of the rule which action triggered
- this YYABORT or YYACCEPT. */
- YYPOPSTACK (yylen);
- YY_STACK_PRINT (yyss, yyssp);
- while (yyssp != yyss)
- {
- yydestruct ("Cleanup: popping",
-- yystos[*yyssp], yyvsp, yylsp);
-+ yystos[*yyssp], yyvsp, yylsp);
- YYPOPSTACK (1);
- }
- #ifndef yyoverflow
-@@ -2246,12 +2462,18 @@ yyreturn:
- if (yymsg != yymsgbuf)
- YYSTACK_FREE (yymsg);
- #endif
-- return yyresult;
-+ /* Make sure YYID is used. */
-+ return YYID (yyresult);
- }
--#line 472 "dtc-parser.y" /* yacc.c:1906 */
-+
-+
-+
-+/* Line 2067 of yacc.c */
-+#line 489 "dtc-parser.y"
-
-
- void yyerror(char const *s)
- {
- ERROR(&yylloc, "%s", s);
- }
-+
---- a/scripts/dtc/dtc-parser.tab.h_shipped
-+++ b/scripts/dtc/dtc-parser.tab.h_shipped
-@@ -1,19 +1,19 @@
--/* A Bison parser, made by GNU Bison 3.0.2. */
-+/* A Bison parser, made by GNU Bison 2.5. */
-
- /* Bison interface for Yacc-like parsers in C
--
-- Copyright (C) 1984, 1989-1990, 2000-2013 Free Software Foundation, Inc.
--
-+
-+ Copyright (C) 1984, 1989-1990, 2000-2011 Free Software Foundation, Inc.
-+
- This program is free software: you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation, either version 3 of the License, or
- (at your option) any later version.
--
-+
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
--
-+
- You should have received a copy of the GNU General Public License
- along with this program. If not, see <http://www.gnu.org/licenses/>. */
-
-@@ -26,55 +26,50 @@
- special exception, which will cause the skeleton and the resulting
- Bison output files to be licensed under the GNU General Public
- License without this special exception.
--
-+
- This special exception was added by the Free Software Foundation in
- version 2.2 of Bison. */
-
--#ifndef YY_YY_DTC_PARSER_TAB_H_INCLUDED
--# define YY_YY_DTC_PARSER_TAB_H_INCLUDED
--/* Debug traces. */
--#ifndef YYDEBUG
--# define YYDEBUG 0
--#endif
--#if YYDEBUG
--extern int yydebug;
--#endif
-
--/* Token type. */
-+/* Tokens. */
- #ifndef YYTOKENTYPE
- # define YYTOKENTYPE
-- enum yytokentype
-- {
-- DT_V1 = 258,
-- DT_MEMRESERVE = 259,
-- DT_LSHIFT = 260,
-- DT_RSHIFT = 261,
-- DT_LE = 262,
-- DT_GE = 263,
-- DT_EQ = 264,
-- DT_NE = 265,
-- DT_AND = 266,
-- DT_OR = 267,
-- DT_BITS = 268,
-- DT_DEL_PROP = 269,
-- DT_DEL_NODE = 270,
-- DT_PROPNODENAME = 271,
-- DT_LITERAL = 272,
-- DT_CHAR_LITERAL = 273,
-- DT_BYTE = 274,
-- DT_STRING = 275,
-- DT_LABEL = 276,
-- DT_REF = 277,
-- DT_INCBIN = 278
-- };
-+ /* Put the tokens into the symbol table, so that GDB and other debuggers
-+ know about them. */
-+ enum yytokentype {
-+ DT_V1 = 258,
-+ DT_PLUGIN = 259,
-+ DT_MEMRESERVE = 260,
-+ DT_LSHIFT = 261,
-+ DT_RSHIFT = 262,
-+ DT_LE = 263,
-+ DT_GE = 264,
-+ DT_EQ = 265,
-+ DT_NE = 266,
-+ DT_AND = 267,
-+ DT_OR = 268,
-+ DT_BITS = 269,
-+ DT_DEL_PROP = 270,
-+ DT_DEL_NODE = 271,
-+ DT_PROPNODENAME = 272,
-+ DT_LITERAL = 273,
-+ DT_CHAR_LITERAL = 274,
-+ DT_BYTE = 275,
-+ DT_STRING = 276,
-+ DT_LABEL = 277,
-+ DT_REF = 278,
-+ DT_INCBIN = 279
-+ };
- #endif
-
--/* Value type. */
-+
-+
- #if ! defined YYSTYPE && ! defined YYSTYPE_IS_DECLARED
--typedef union YYSTYPE YYSTYPE;
--union YYSTYPE
-+typedef union YYSTYPE
- {
--#line 38 "dtc-parser.y" /* yacc.c:1909 */
-+
-+/* Line 2068 of yacc.c */
-+#line 39 "dtc-parser.y"
-
- char *propnodename;
- char *labelref;
-@@ -92,30 +87,32 @@ union YYSTYPE
- struct node *nodelist;
- struct reserve_info *re;
- uint64_t integer;
-+ int is_plugin;
-+
-+
-
--#line 97 "dtc-parser.tab.h" /* yacc.c:1909 */
--};
-+/* Line 2068 of yacc.c */
-+#line 96 "dtc-parser.tab.h"
-+} YYSTYPE;
- # define YYSTYPE_IS_TRIVIAL 1
-+# define yystype YYSTYPE /* obsolescent; will be withdrawn */
- # define YYSTYPE_IS_DECLARED 1
- #endif
-
--/* Location type. */
-+extern YYSTYPE yylval;
-+
- #if ! defined YYLTYPE && ! defined YYLTYPE_IS_DECLARED
--typedef struct YYLTYPE YYLTYPE;
--struct YYLTYPE
-+typedef struct YYLTYPE
- {
- int first_line;
- int first_column;
- int last_line;
- int last_column;
--};
-+} YYLTYPE;
-+# define yyltype YYLTYPE /* obsolescent; will be withdrawn */
- # define YYLTYPE_IS_DECLARED 1
- # define YYLTYPE_IS_TRIVIAL 1
- #endif
-
--
--extern YYSTYPE yylval;
- extern YYLTYPE yylloc;
--int yyparse (void);
-
--#endif /* !YY_YY_DTC_PARSER_TAB_H_INCLUDED */
---- a/scripts/dtc/dtc-parser.y
-+++ b/scripts/dtc/dtc-parser.y
-@@ -19,6 +19,7 @@
- */
- %{
- #include <stdio.h>
-+#include <inttypes.h>
-
- #include "dtc.h"
- #include "srcpos.h"
-@@ -52,9 +53,11 @@ extern bool treesource_error;
- struct node *nodelist;
- struct reserve_info *re;
- uint64_t integer;
-+ int is_plugin;
- }
-
- %token DT_V1
-+%token DT_PLUGIN
- %token DT_MEMRESERVE
- %token DT_LSHIFT DT_RSHIFT DT_LE DT_GE DT_EQ DT_NE DT_AND DT_OR
- %token DT_BITS
-@@ -71,6 +74,7 @@ extern bool treesource_error;
-
- %type <data> propdata
- %type <data> propdataprefix
-+%type <is_plugin> plugindecl
- %type <re> memreserve
- %type <re> memreserves
- %type <array> arrayprefix
-@@ -101,10 +105,23 @@ extern bool treesource_error;
- %%
-
- sourcefile:
-- DT_V1 ';' memreserves devicetree
-+ DT_V1 ';' plugindecl memreserves devicetree
- {
-- the_boot_info = build_boot_info($3, $4,
-- guess_boot_cpuid($4));
-+ $5->is_plugin = $3;
-+ $5->is_root = 1;
-+ the_boot_info = build_boot_info($4, $5,
-+ guess_boot_cpuid($5));
-+ }
-+ ;
-+
-+plugindecl:
-+ /* empty */
-+ {
-+ $$ = 0;
-+ }
-+ | DT_PLUGIN ';'
-+ {
-+ $$ = 1;
- }
- ;
-
---- a/scripts/dtc/dtc.c
-+++ b/scripts/dtc/dtc.c
-@@ -29,6 +29,7 @@ int reservenum; /* Number of memory res
- int minsize; /* Minimum blob size */
- int padsize; /* Additional padding to blob */
- int phandle_format = PHANDLE_BOTH; /* Use linux,phandle or phandle properties */
-+int symbol_fixup_support = 0;
-
- static void fill_fullpaths(struct node *tree, const char *prefix)
- {
-@@ -51,7 +52,7 @@ static void fill_fullpaths(struct node *
- #define FDT_VERSION(version) _FDT_VERSION(version)
- #define _FDT_VERSION(version) #version
- static const char usage_synopsis[] = "dtc [options] <input file>";
--static const char usage_short_opts[] = "qI:O:o:V:d:R:S:p:fb:i:H:sW:E:hv";
-+static const char usage_short_opts[] = "qI:O:o:V:d:R:S:p:fb:i:H:sW:E:hv@";
- static struct option const usage_long_opts[] = {
- {"quiet", no_argument, NULL, 'q'},
- {"in-format", a_argument, NULL, 'I'},
-@@ -69,6 +70,7 @@ static struct option const usage_long_op
- {"phandle", a_argument, NULL, 'H'},
- {"warning", a_argument, NULL, 'W'},
- {"error", a_argument, NULL, 'E'},
-+ {"symbols", a_argument, NULL, '@'},
- {"help", no_argument, NULL, 'h'},
- {"version", no_argument, NULL, 'v'},
- {NULL, no_argument, NULL, 0x0},
-@@ -99,6 +101,7 @@ static const char * const usage_opts_hel
- "\t\tboth - Both \"linux,phandle\" and \"phandle\" properties",
- "\n\tEnable/disable warnings (prefix with \"no-\")",
- "\n\tEnable/disable errors (prefix with \"no-\")",
-+ "\n\tSymbols and Fixups support",
- "\n\tPrint this help and exit",
- "\n\tPrint version and exit",
- NULL,
-@@ -186,7 +189,9 @@ int main(int argc, char *argv[])
- case 'E':
- parse_checks_option(false, true, optarg);
- break;
--
-+ case '@':
-+ symbol_fixup_support = 1;
-+ break;
- case 'h':
- usage(NULL);
- default:
---- a/scripts/dtc/dtc.h
-+++ b/scripts/dtc/dtc.h
-@@ -54,6 +54,7 @@ extern int reservenum; /* Number of mem
- extern int minsize; /* Minimum blob size */
- extern int padsize; /* Additional padding to blob */
- extern int phandle_format; /* Use linux,phandle or phandle properties */
-+extern int symbol_fixup_support;/* enable symbols & fixup support */
-
- #define PHANDLE_LEGACY 0x1
- #define PHANDLE_EPAPR 0x2
-@@ -132,6 +133,25 @@ struct label {
- struct label *next;
- };
-
-+struct fixup_entry {
-+ int offset;
-+ struct node *node;
-+ struct property *prop;
-+ struct fixup_entry *next;
-+};
-+
-+struct fixup {
-+ char *ref;
-+ struct fixup_entry *entries;
-+ struct fixup *next;
-+};
-+
-+struct symbol {
-+ struct label *label;
-+ struct node *node;
-+ struct symbol *next;
-+};
-+
- struct property {
- bool deleted;
- char *name;
-@@ -158,6 +178,12 @@ struct node {
- int addr_cells, size_cells;
-
- struct label *labels;
-+
-+ int is_root;
-+ int is_plugin;
-+ struct fixup *fixups;
-+ struct symbol *symbols;
-+ struct fixup_entry *local_fixups;
- };
-
- #define for_each_label_withdel(l0, l) \
-@@ -181,6 +207,18 @@ struct node {
- for_each_child_withdel(n, c) \
- if (!(c)->deleted)
-
-+#define for_each_fixup(n, f) \
-+ for ((f) = (n)->fixups; (f); (f) = (f)->next)
-+
-+#define for_each_fixup_entry(f, fe) \
-+ for ((fe) = (f)->entries; (fe); (fe) = (fe)->next)
-+
-+#define for_each_symbol(n, s) \
-+ for ((s) = (n)->symbols; (s); (s) = (s)->next)
-+
-+#define for_each_local_fixup_entry(n, fe) \
-+ for ((fe) = (n)->local_fixups; (fe); (fe) = (fe)->next)
-+
- void add_label(struct label **labels, char *label);
- void delete_labels(struct label **labels);
-
---- a/scripts/dtc/flattree.c
-+++ b/scripts/dtc/flattree.c
-@@ -262,6 +262,12 @@ static void flatten_tree(struct node *tr
- struct property *prop;
- struct node *child;
- bool seen_name_prop = false;
-+ struct symbol *sym;
-+ struct fixup *f;
-+ struct fixup_entry *fe;
-+ char *name, *s;
-+ const char *fullpath;
-+ int namesz, nameoff, vallen;
-
- if (tree->deleted)
- return;
-@@ -276,8 +282,6 @@ static void flatten_tree(struct node *tr
- emit->align(etarget, sizeof(cell_t));
-
- for_each_property(tree, prop) {
-- int nameoff;
--
- if (streq(prop->name, "name"))
- seen_name_prop = true;
-
-@@ -310,6 +314,139 @@ static void flatten_tree(struct node *tr
- flatten_tree(child, emit, etarget, strbuf, vi);
- }
-
-+ if (!symbol_fixup_support)
-+ goto no_symbols;
-+
-+ /* add the symbol nodes (if any) */
-+ if (tree->symbols) {
-+
-+ emit->beginnode(etarget, NULL);
-+ emit->string(etarget, "__symbols__", 0);
-+ emit->align(etarget, sizeof(cell_t));
-+
-+ for_each_symbol(tree, sym) {
-+
-+ vallen = strlen(sym->node->fullpath);
-+
-+ nameoff = stringtable_insert(strbuf, sym->label->label);
-+
-+ emit->property(etarget, NULL);
-+ emit->cell(etarget, vallen + 1);
-+ emit->cell(etarget, nameoff);
-+
-+ if ((vi->flags & FTF_VARALIGN) && vallen >= 8)
-+ emit->align(etarget, 8);
-+
-+ emit->string(etarget, sym->node->fullpath,
-+ strlen(sym->node->fullpath));
-+ emit->align(etarget, sizeof(cell_t));
-+ }
-+
-+ emit->endnode(etarget, NULL);
-+ }
-+
-+ /* add the fixup nodes */
-+ if (tree->fixups) {
-+
-+ /* emit the external fixups */
-+ emit->beginnode(etarget, NULL);
-+ emit->string(etarget, "__fixups__", 0);
-+ emit->align(etarget, sizeof(cell_t));
-+
-+ for_each_fixup(tree, f) {
-+
-+ namesz = 0;
-+ for_each_fixup_entry(f, fe) {
-+ fullpath = fe->node->fullpath;
-+ if (fullpath[0] == '\0')
-+ fullpath = "/";
-+ namesz += strlen(fullpath) + 1;
-+ namesz += strlen(fe->prop->name) + 1;
-+ namesz += 32; /* space for :<number> + '\0' */
-+ }
-+
-+ name = xmalloc(namesz);
-+
-+ s = name;
-+ for_each_fixup_entry(f, fe) {
-+ fullpath = fe->node->fullpath;
-+ if (fullpath[0] == '\0')
-+ fullpath = "/";
-+ snprintf(s, name + namesz - s, "%s:%s:%d",
-+ fullpath,
-+ fe->prop->name, fe->offset);
-+ s += strlen(s) + 1;
-+ }
-+
-+ nameoff = stringtable_insert(strbuf, f->ref);
-+ vallen = s - name - 1;
-+
-+ emit->property(etarget, NULL);
-+ emit->cell(etarget, vallen + 1);
-+ emit->cell(etarget, nameoff);
-+
-+ if ((vi->flags & FTF_VARALIGN) && vallen >= 8)
-+ emit->align(etarget, 8);
-+
-+ emit->string(etarget, name, vallen);
-+ emit->align(etarget, sizeof(cell_t));
-+
-+ free(name);
-+ }
-+
-+ emit->endnode(etarget, tree->labels);
-+ }
-+
-+ /* add the local fixup property */
-+ if (tree->local_fixups) {
-+
-+ /* emit the external fixups */
-+ emit->beginnode(etarget, NULL);
-+ emit->string(etarget, "__local_fixups__", 0);
-+ emit->align(etarget, sizeof(cell_t));
-+
-+ namesz = 0;
-+ for_each_local_fixup_entry(tree, fe) {
-+ fullpath = fe->node->fullpath;
-+ if (fullpath[0] == '\0')
-+ fullpath = "/";
-+ namesz += strlen(fullpath) + 1;
-+ namesz += strlen(fe->prop->name) + 1;
-+ namesz += 32; /* space for :<number> + '\0' */
-+ }
-+
-+ name = xmalloc(namesz);
-+
-+ s = name;
-+ for_each_local_fixup_entry(tree, fe) {
-+ fullpath = fe->node->fullpath;
-+ if (fullpath[0] == '\0')
-+ fullpath = "/";
-+ snprintf(s, name + namesz - s, "%s:%s:%d",
-+ fullpath, fe->prop->name,
-+ fe->offset);
-+ s += strlen(s) + 1;
-+ }
-+
-+ nameoff = stringtable_insert(strbuf, "fixup");
-+ vallen = s - name - 1;
-+
-+ emit->property(etarget, NULL);
-+ emit->cell(etarget, vallen + 1);
-+ emit->cell(etarget, nameoff);
-+
-+ if ((vi->flags & FTF_VARALIGN) && vallen >= 8)
-+ emit->align(etarget, 8);
-+
-+ emit->string(etarget, name, vallen);
-+ emit->align(etarget, sizeof(cell_t));
-+
-+ free(name);
-+
-+ emit->endnode(etarget, tree->labels);
-+ }
-+
-+no_symbols:
- emit->endnode(etarget, tree->labels);
- }
-
---- a/scripts/dtc/version_gen.h
-+++ b/scripts/dtc/version_gen.h
-@@ -1 +1 @@
--#define DTC_VERSION "DTC 1.4.1-g9d3649bd"
-+#define DTC_VERSION "DTC 1.4.1-g9d3649bd-dirty"
diff --git a/target/linux/brcm2708/patches-4.4/0083-mfd-Add-Raspberry-Pi-Sense-HAT-core-driver.patch b/target/linux/brcm2708/patches-4.4/0083-mfd-Add-Raspberry-Pi-Sense-HAT-core-driver.patch
deleted file mode 100644
index dff18c6..0000000
--- a/target/linux/brcm2708/patches-4.4/0083-mfd-Add-Raspberry-Pi-Sense-HAT-core-driver.patch
+++ /dev/null
@@ -1,838 +0,0 @@
-From 9a7c0060167398fa754a2b8a9b1faaac40977b6f Mon Sep 17 00:00:00 2001
-From: Phil Elwell <pelwell at users.noreply.github.com>
-Date: Tue, 14 Jul 2015 14:32:47 +0100
-Subject: [PATCH] mfd: Add Raspberry Pi Sense HAT core driver
-
----
- drivers/input/joystick/Kconfig | 8 +
- drivers/input/joystick/Makefile | 1 +
- drivers/input/joystick/rpisense-js.c | 153 ++++++++++++++++
- drivers/mfd/Kconfig | 8 +
- drivers/mfd/Makefile | 2 +
- drivers/mfd/rpisense-core.c | 157 +++++++++++++++++
- drivers/video/fbdev/Kconfig | 13 ++
- drivers/video/fbdev/Makefile | 1 +
- drivers/video/fbdev/rpisense-fb.c | 293 +++++++++++++++++++++++++++++++
- include/linux/mfd/rpisense/core.h | 47 +++++
- include/linux/mfd/rpisense/framebuffer.h | 32 ++++
- include/linux/mfd/rpisense/joystick.h | 35 ++++
- 12 files changed, 750 insertions(+)
- create mode 100644 drivers/input/joystick/rpisense-js.c
- create mode 100644 drivers/mfd/rpisense-core.c
- create mode 100644 drivers/video/fbdev/rpisense-fb.c
- create mode 100644 include/linux/mfd/rpisense/core.h
- create mode 100644 include/linux/mfd/rpisense/framebuffer.h
- create mode 100644 include/linux/mfd/rpisense/joystick.h
-
---- a/drivers/input/joystick/Kconfig
-+++ b/drivers/input/joystick/Kconfig
-@@ -330,4 +330,12 @@ config JOYSTICK_MAPLE
- To compile this as a module choose M here: the module will be called
- maplecontrol.
-
-+config JOYSTICK_RPISENSE
-+ tristate "Raspberry Pi Sense HAT joystick"
-+ depends on GPIOLIB && INPUT
-+ select MFD_RPISENSE_CORE
-+
-+ help
-+ This is the joystick driver for the Raspberry Pi Sense HAT
-+
- endif
---- a/drivers/input/joystick/Makefile
-+++ b/drivers/input/joystick/Makefile
-@@ -32,4 +32,5 @@ obj-$(CONFIG_JOYSTICK_WARRIOR) += warri
- obj-$(CONFIG_JOYSTICK_XPAD) += xpad.o
- obj-$(CONFIG_JOYSTICK_ZHENHUA) += zhenhua.o
- obj-$(CONFIG_JOYSTICK_WALKERA0701) += walkera0701.o
-+obj-$(CONFIG_JOYSTICK_RPISENSE) += rpisense-js.o
-
---- /dev/null
-+++ b/drivers/input/joystick/rpisense-js.c
-@@ -0,0 +1,153 @@
-+/*
-+ * Raspberry Pi Sense HAT joystick driver
-+ * http://raspberrypi.org
-+ *
-+ * Copyright (C) 2015 Raspberry Pi
-+ *
-+ * Author: Serge Schneider
-+ *
-+ * This program is free software; you can redistribute it and/or modify it
-+ * under the terms of the GNU General Public License as published by the
-+ * Free Software Foundation; either version 2 of the License, or (at your
-+ * option) any later version.
-+ *
-+ */
-+
-+#include <linux/module.h>
-+
-+#include <linux/mfd/rpisense/joystick.h>
-+#include <linux/mfd/rpisense/core.h>
-+
-+static struct rpisense *rpisense;
-+static unsigned char keymap[5] = {KEY_DOWN, KEY_RIGHT, KEY_UP, KEY_ENTER, KEY_LEFT,};
-+
-+static void keys_work_fn(struct work_struct *work)
-+{
-+ int i;
-+ static s32 prev_keys;
-+ struct rpisense_js *rpisense_js = &rpisense->joystick;
-+ s32 keys = rpisense_reg_read(rpisense, RPISENSE_KEYS);
-+ s32 changes = keys ^ prev_keys;
-+
-+ prev_keys = keys;
-+ for (i = 0; i < 5; i++) {
-+ if (changes & 1) {
-+ input_report_key(rpisense_js->keys_dev,
-+ keymap[i], keys & 1);
-+ }
-+ changes >>= 1;
-+ keys >>= 1;
-+ }
-+ input_sync(rpisense_js->keys_dev);
-+}
-+
-+static irqreturn_t keys_irq_handler(int irq, void *pdev)
-+{
-+ struct rpisense_js *rpisense_js = &rpisense->joystick;
-+
-+ schedule_work(&rpisense_js->keys_work_s);
-+ return IRQ_HANDLED;
-+}
-+
-+static int rpisense_js_probe(struct platform_device *pdev)
-+{
-+ int ret;
-+ int i;
-+ struct rpisense_js *rpisense_js;
-+
-+ rpisense = rpisense_get_dev();
-+ rpisense_js = &rpisense->joystick;
-+
-+ INIT_WORK(&rpisense_js->keys_work_s, keys_work_fn);
-+
-+ rpisense_js->keys_dev = input_allocate_device();
-+ if (!rpisense_js->keys_dev) {
-+ dev_err(&pdev->dev, "Could not allocate input device.\n");
-+ return -ENOMEM;
-+ }
-+
-+ rpisense_js->keys_dev->evbit[0] = BIT_MASK(EV_KEY);
-+ for (i = 0; i < ARRAY_SIZE(keymap); i++) {
-+ set_bit(keymap[i],
-+ rpisense_js->keys_dev->keybit);
-+ }
-+
-+ rpisense_js->keys_dev->name = "Raspberry Pi Sense HAT Joystick";
-+ rpisense_js->keys_dev->phys = "rpi-sense-joy/input0";
-+ rpisense_js->keys_dev->id.bustype = BUS_I2C;
-+ rpisense_js->keys_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_REP);
-+ rpisense_js->keys_dev->keycode = keymap;
-+ rpisense_js->keys_dev->keycodesize = sizeof(unsigned char);
-+ rpisense_js->keys_dev->keycodemax = ARRAY_SIZE(keymap);
-+
-+ ret = input_register_device(rpisense_js->keys_dev);
-+ if (ret) {
-+ dev_err(&pdev->dev, "Could not register input device.\n");
-+ goto err_keys_alloc;
-+ }
-+
-+ ret = gpiod_direction_input(rpisense_js->keys_desc);
-+ if (ret) {
-+ dev_err(&pdev->dev, "Could not set keys-int direction.\n");
-+ goto err_keys_reg;
-+ }
-+
-+ rpisense_js->keys_irq = gpiod_to_irq(rpisense_js->keys_desc);
-+ if (rpisense_js->keys_irq < 0) {
-+ dev_err(&pdev->dev, "Could not determine keys-int IRQ.\n");
-+ ret = rpisense_js->keys_irq;
-+ goto err_keys_reg;
-+ }
-+
-+ ret = devm_request_irq(&pdev->dev, rpisense_js->keys_irq,
-+ keys_irq_handler, IRQF_TRIGGER_RISING,
-+ "keys", &pdev->dev);
-+ if (ret) {
-+ dev_err(&pdev->dev, "IRQ request failed.\n");
-+ goto err_keys_reg;
-+ }
-+ return 0;
-+err_keys_reg:
-+ input_unregister_device(rpisense_js->keys_dev);
-+err_keys_alloc:
-+ input_free_device(rpisense_js->keys_dev);
-+ return ret;
-+}
-+
-+static int rpisense_js_remove(struct platform_device *pdev)
-+{
-+ struct rpisense_js *rpisense_js = &rpisense->joystick;
-+
-+ input_unregister_device(rpisense_js->keys_dev);
-+ input_free_device(rpisense_js->keys_dev);
-+ return 0;
-+}
-+
-+#ifdef CONFIG_OF
-+static const struct of_device_id rpisense_js_id[] = {
-+ { .compatible = "rpi,rpi-sense-js" },
-+ { },
-+};
-+MODULE_DEVICE_TABLE(of, rpisense_js_id);
-+#endif
-+
-+static struct platform_device_id rpisense_js_device_id[] = {
-+ { .name = "rpi-sense-js" },
-+ { },
-+};
-+MODULE_DEVICE_TABLE(platform, rpisense_js_device_id);
-+
-+static struct platform_driver rpisense_js_driver = {
-+ .probe = rpisense_js_probe,
-+ .remove = rpisense_js_remove,
-+ .driver = {
-+ .name = "rpi-sense-js",
-+ .owner = THIS_MODULE,
-+ },
-+};
-+
-+module_platform_driver(rpisense_js_driver);
-+
-+MODULE_DESCRIPTION("Raspberry Pi Sense HAT joystick driver");
-+MODULE_AUTHOR("Serge Schneider <serge at raspberrypi.org>");
-+MODULE_LICENSE("GPL");
---- a/drivers/mfd/Kconfig
-+++ b/drivers/mfd/Kconfig
-@@ -10,6 +10,14 @@ config MFD_CORE
- select IRQ_DOMAIN
- default n
-
-+config MFD_RPISENSE_CORE
-+ tristate "Raspberry Pi Sense HAT core functions"
-+ depends on I2C
-+ select MFD_CORE
-+ help
-+ This is the core driver for the Raspberry Pi Sense HAT. This provides
-+ the necessary functions to communicate with the hardware.
-+
- config MFD_CS5535
- tristate "AMD CS5535 and CS5536 southbridge core functions"
- select MFD_CORE
---- a/drivers/mfd/Makefile
-+++ b/drivers/mfd/Makefile
-@@ -194,3 +194,5 @@ intel-soc-pmic-objs := intel_soc_pmic_c
- intel-soc-pmic-$(CONFIG_INTEL_PMC_IPC) += intel_soc_pmic_bxtwc.o
- obj-$(CONFIG_INTEL_SOC_PMIC) += intel-soc-pmic.o
- obj-$(CONFIG_MFD_MT6397) += mt6397-core.o
-+
-+obj-$(CONFIG_MFD_RPISENSE_CORE) += rpisense-core.o
---- /dev/null
-+++ b/drivers/mfd/rpisense-core.c
-@@ -0,0 +1,157 @@
-+/*
-+ * Raspberry Pi Sense HAT core driver
-+ * http://raspberrypi.org
-+ *
-+ * Copyright (C) 2015 Raspberry Pi
-+ *
-+ * Author: Serge Schneider
-+ *
-+ * This program is free software; you can redistribute it and/or modify it
-+ * under the terms of the GNU General Public License as published by the
-+ * Free Software Foundation; either version 2 of the License, or (at your
-+ * option) any later version.
-+ *
-+ * This driver is based on wm8350 implementation.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/moduleparam.h>
-+#include <linux/err.h>
-+#include <linux/init.h>
-+#include <linux/i2c.h>
-+#include <linux/platform_device.h>
-+#include <linux/mfd/rpisense/core.h>
-+#include <linux/slab.h>
-+
-+static struct rpisense *rpisense;
-+
-+static void rpisense_client_dev_register(struct rpisense *rpisense,
-+ const char *name,
-+ struct platform_device **pdev)
-+{
-+ int ret;
-+
-+ *pdev = platform_device_alloc(name, -1);
-+ if (*pdev == NULL) {
-+ dev_err(rpisense->dev, "Failed to allocate %s\n", name);
-+ return;
-+ }
-+
-+ (*pdev)->dev.parent = rpisense->dev;
-+ platform_set_drvdata(*pdev, rpisense);
-+ ret = platform_device_add(*pdev);
-+ if (ret != 0) {
-+ dev_err(rpisense->dev, "Failed to register %s: %d\n",
-+ name, ret);
-+ platform_device_put(*pdev);
-+ *pdev = NULL;
-+ }
-+}
-+
-+static int rpisense_probe(struct i2c_client *i2c,
-+ const struct i2c_device_id *id)
-+{
-+ int ret;
-+ struct rpisense_js *rpisense_js;
-+
-+ rpisense = devm_kzalloc(&i2c->dev, sizeof(struct rpisense), GFP_KERNEL);
-+ if (rpisense == NULL)
-+ return -ENOMEM;
-+
-+ i2c_set_clientdata(i2c, rpisense);
-+ rpisense->dev = &i2c->dev;
-+ rpisense->i2c_client = i2c;
-+
-+ ret = rpisense_reg_read(rpisense, RPISENSE_WAI);
-+ if (ret > 0) {
-+ if (ret != 's')
-+ return -EINVAL;
-+ } else {
-+ return ret;
-+ }
-+ ret = rpisense_reg_read(rpisense, RPISENSE_VER);
-+ if (ret < 0)
-+ return ret;
-+
-+ dev_info(rpisense->dev,
-+ "Raspberry Pi Sense HAT firmware version %i\n", ret);
-+
-+ rpisense_js = &rpisense->joystick;
-+ rpisense_js->keys_desc = devm_gpiod_get(&i2c->dev,
-+ "keys-int", GPIOD_IN);
-+ if (IS_ERR(rpisense_js->keys_desc)) {
-+ dev_warn(&i2c->dev, "Failed to get keys-int descriptor.\n");
-+ rpisense_js->keys_desc = gpio_to_desc(23);
-+ if (rpisense_js->keys_desc == NULL) {
-+ dev_err(&i2c->dev, "GPIO23 fallback failed.\n");
-+ return PTR_ERR(rpisense_js->keys_desc);
-+ }
-+ }
-+ rpisense_client_dev_register(rpisense, "rpi-sense-js",
-+ &(rpisense->joystick.pdev));
-+ rpisense_client_dev_register(rpisense, "rpi-sense-fb",
-+ &(rpisense->framebuffer.pdev));
-+
-+ return 0;
-+}
-+
-+static int rpisense_remove(struct i2c_client *i2c)
-+{
-+ struct rpisense *rpisense = i2c_get_clientdata(i2c);
-+
-+ platform_device_unregister(rpisense->joystick.pdev);
-+ return 0;
-+}
-+
-+struct rpisense *rpisense_get_dev(void)
-+{
-+ return rpisense;
-+}
-+EXPORT_SYMBOL_GPL(rpisense_get_dev);
-+
-+s32 rpisense_reg_read(struct rpisense *rpisense, int reg)
-+{
-+ int ret = i2c_smbus_read_byte_data(rpisense->i2c_client, reg);
-+
-+ if (ret < 0)
-+ dev_err(rpisense->dev, "Read from reg %d failed\n", reg);
-+ /* Due to the BCM270x I2C clock stretching bug, some values
-+ * may have MSB set. Clear it to avoid incorrect values.
-+ * */
-+ return ret & 0x7F;
-+}
-+EXPORT_SYMBOL_GPL(rpisense_reg_read);
-+
-+int rpisense_block_write(struct rpisense *rpisense, const char *buf, int count)
-+{
-+ int ret = i2c_master_send(rpisense->i2c_client, buf, count);
-+
-+ if (ret < 0)
-+ dev_err(rpisense->dev, "Block write failed\n");
-+ return ret;
-+}
-+EXPORT_SYMBOL_GPL(rpisense_block_write);
-+
-+static const struct i2c_device_id rpisense_i2c_id[] = {
-+ { "rpi-sense", 0 },
-+ { }
-+};
-+MODULE_DEVICE_TABLE(i2c, rpisense_i2c_id);
-+
-+
-+static struct i2c_driver rpisense_driver = {
-+ .driver = {
-+ .name = "rpi-sense",
-+ .owner = THIS_MODULE,
-+ },
-+ .probe = rpisense_probe,
-+ .remove = rpisense_remove,
-+ .id_table = rpisense_i2c_id,
-+};
-+
-+module_i2c_driver(rpisense_driver);
-+
-+MODULE_DESCRIPTION("Raspberry Pi Sense HAT core driver");
-+MODULE_AUTHOR("Serge Schneider <serge at raspberrypi.org>");
-+MODULE_LICENSE("GPL");
-+
---- a/drivers/video/fbdev/Kconfig
-+++ b/drivers/video/fbdev/Kconfig
-@@ -2505,3 +2505,16 @@ config FB_SM712
- This driver is also available as a module. The module will be
- called sm712fb. If you want to compile it as a module, say M
- here and read <file:Documentation/kbuild/modules.txt>.
-+
-+config FB_RPISENSE
-+ tristate "Raspberry Pi Sense HAT framebuffer"
-+ depends on FB
-+ select MFD_RPISENSE_CORE
-+ select FB_SYS_FOPS
-+ select FB_SYS_FILLRECT
-+ select FB_SYS_COPYAREA
-+ select FB_SYS_IMAGEBLIT
-+ select FB_DEFERRED_IO
-+
-+ help
-+ This is the framebuffer driver for the Raspberry Pi Sense HAT
---- a/drivers/video/fbdev/Makefile
-+++ b/drivers/video/fbdev/Makefile
-@@ -150,6 +150,7 @@ obj-$(CONFIG_FB_DA8XX) += da8xx-fb.o
- obj-$(CONFIG_FB_MXS) += mxsfb.o
- obj-$(CONFIG_FB_SSD1307) += ssd1307fb.o
- obj-$(CONFIG_FB_SIMPLE) += simplefb.o
-+obj-$(CONFIG_FB_RPISENSE) += rpisense-fb.o
-
- # the test framebuffer is last
- obj-$(CONFIG_FB_VIRTUAL) += vfb.o
---- /dev/null
-+++ b/drivers/video/fbdev/rpisense-fb.c
-@@ -0,0 +1,293 @@
-+/*
-+ * Raspberry Pi Sense HAT framebuffer driver
-+ * http://raspberrypi.org
-+ *
-+ * Copyright (C) 2015 Raspberry Pi
-+ *
-+ * Author: Serge Schneider
-+ *
-+ * This program is free software; you can redistribute it and/or modify it
-+ * under the terms of the GNU General Public License as published by the
-+ * Free Software Foundation; either version 2 of the License, or (at your
-+ * option) any later version.
-+ *
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/kernel.h>
-+#include <linux/errno.h>
-+#include <linux/string.h>
-+#include <linux/mm.h>
-+#include <linux/slab.h>
-+#include <linux/uaccess.h>
-+#include <linux/delay.h>
-+#include <linux/fb.h>
-+#include <linux/init.h>
-+
-+#include <linux/mfd/rpisense/framebuffer.h>
-+#include <linux/mfd/rpisense/core.h>
-+
-+static bool lowlight;
-+module_param(lowlight, bool, 0);
-+MODULE_PARM_DESC(lowlight, "Reduce LED matrix brightness to one third");
-+
-+static struct rpisense *rpisense;
-+
-+struct rpisense_fb_param {
-+ char __iomem *vmem;
-+ u8 *vmem_work;
-+ u32 vmemsize;
-+ u8 *gamma;
-+};
-+
-+static u8 gamma_default[32] = {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01, 0x01,
-+ 0x02, 0x02, 0x03, 0x03, 0x04, 0x05, 0x06, 0x07,
-+ 0x08, 0x09, 0x0A, 0x0B, 0x0C, 0x0E, 0x0F, 0x11,
-+ 0x12, 0x14, 0x15, 0x17, 0x19, 0x1B, 0x1D, 0x1F,};
-+
-+static u8 gamma_low[32] = {0x00, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01,
-+ 0x01, 0x01, 0x01, 0x01, 0x01, 0x02, 0x02, 0x02,
-+ 0x03, 0x03, 0x03, 0x04, 0x04, 0x05, 0x05, 0x06,
-+ 0x06, 0x07, 0x07, 0x08, 0x08, 0x09, 0x0A, 0x0A,};
-+
-+static u8 gamma_user[32];
-+
-+static struct rpisense_fb_param rpisense_fb_param = {
-+ .vmem = NULL,
-+ .vmemsize = 128,
-+ .gamma = gamma_default,
-+};
-+
-+static struct fb_deferred_io rpisense_fb_defio;
-+
-+static struct fb_fix_screeninfo rpisense_fb_fix = {
-+ .id = "RPi-Sense FB",
-+ .type = FB_TYPE_PACKED_PIXELS,
-+ .visual = FB_VISUAL_TRUECOLOR,
-+ .xpanstep = 0,
-+ .ypanstep = 0,
-+ .ywrapstep = 0,
-+ .accel = FB_ACCEL_NONE,
-+ .line_length = 16,
-+};
-+
-+static struct fb_var_screeninfo rpisense_fb_var = {
-+ .xres = 8,
-+ .yres = 8,
-+ .xres_virtual = 8,
-+ .yres_virtual = 8,
-+ .bits_per_pixel = 16,
-+ .red = {11, 5, 0},
-+ .green = {5, 6, 0},
-+ .blue = {0, 5, 0},
-+};
-+
-+static ssize_t rpisense_fb_write(struct fb_info *info,
-+ const char __user *buf, size_t count,
-+ loff_t *ppos)
-+{
-+ ssize_t res = fb_sys_write(info, buf, count, ppos);
-+
-+ schedule_delayed_work(&info->deferred_work, rpisense_fb_defio.delay);
-+ return res;
-+}
-+
-+static void rpisense_fb_fillrect(struct fb_info *info,
-+ const struct fb_fillrect *rect)
-+{
-+ sys_fillrect(info, rect);
-+ schedule_delayed_work(&info->deferred_work, rpisense_fb_defio.delay);
-+}
-+
-+static void rpisense_fb_copyarea(struct fb_info *info,
-+ const struct fb_copyarea *area)
-+{
-+ sys_copyarea(info, area);
-+ schedule_delayed_work(&info->deferred_work, rpisense_fb_defio.delay);
-+}
-+
-+static void rpisense_fb_imageblit(struct fb_info *info,
-+ const struct fb_image *image)
-+{
-+ sys_imageblit(info, image);
-+ schedule_delayed_work(&info->deferred_work, rpisense_fb_defio.delay);
-+}
-+
-+static void rpisense_fb_deferred_io(struct fb_info *info,
-+ struct list_head *pagelist)
-+{
-+ int i;
-+ int j;
-+ u8 *vmem_work = rpisense_fb_param.vmem_work;
-+ u16 *mem = (u16 *)rpisense_fb_param.vmem;
-+ u8 *gamma = rpisense_fb_param.gamma;
-+
-+ vmem_work[0] = 0;
-+ for (j = 0; j < 8; j++) {
-+ for (i = 0; i < 8; i++) {
-+ vmem_work[(j * 24) + i + 1] =
-+ gamma[(mem[(j * 8) + i] >> 11) & 0x1F];
-+ vmem_work[(j * 24) + (i + 8) + 1] =
-+ gamma[(mem[(j * 8) + i] >> 6) & 0x1F];
-+ vmem_work[(j * 24) + (i + 16) + 1] =
-+ gamma[(mem[(j * 8) + i]) & 0x1F];
-+ }
-+ }
-+ rpisense_block_write(rpisense, vmem_work, 193);
-+}
-+
-+static struct fb_deferred_io rpisense_fb_defio = {
-+ .delay = HZ/100,
-+ .deferred_io = rpisense_fb_deferred_io,
-+};
-+
-+static int rpisense_fb_ioctl(struct fb_info *info, unsigned int cmd,
-+ unsigned long arg)
-+{
-+ switch (cmd) {
-+ case SENSEFB_FBIOGET_GAMMA:
-+ if (copy_to_user((void __user *) arg, rpisense_fb_param.gamma,
-+ sizeof(u8[32])))
-+ return -EFAULT;
-+ return 0;
-+ case SENSEFB_FBIOSET_GAMMA:
-+ if (copy_from_user(gamma_user, (void __user *)arg,
-+ sizeof(u8[32])))
-+ return -EFAULT;
-+ rpisense_fb_param.gamma = gamma_user;
-+ schedule_delayed_work(&info->deferred_work,
-+ rpisense_fb_defio.delay);
-+ return 0;
-+ case SENSEFB_FBIORESET_GAMMA:
-+ switch (arg) {
-+ case 0:
-+ rpisense_fb_param.gamma = gamma_default;
-+ break;
-+ case 1:
-+ rpisense_fb_param.gamma = gamma_low;
-+ break;
-+ case 2:
-+ rpisense_fb_param.gamma = gamma_user;
-+ break;
-+ default:
-+ return -EINVAL;
-+ }
-+ schedule_delayed_work(&info->deferred_work,
-+ rpisense_fb_defio.delay);
-+ break;
-+ default:
-+ return -EINVAL;
-+ }
-+ return 0;
-+}
-+
-+static struct fb_ops rpisense_fb_ops = {
-+ .owner = THIS_MODULE,
-+ .fb_read = fb_sys_read,
-+ .fb_write = rpisense_fb_write,
-+ .fb_fillrect = rpisense_fb_fillrect,
-+ .fb_copyarea = rpisense_fb_copyarea,
-+ .fb_imageblit = rpisense_fb_imageblit,
-+ .fb_ioctl = rpisense_fb_ioctl,
-+};
-+
-+static int rpisense_fb_probe(struct platform_device *pdev)
-+{
-+ struct fb_info *info;
-+ int ret = -ENOMEM;
-+ struct rpisense_fb *rpisense_fb;
-+
-+ rpisense = rpisense_get_dev();
-+ rpisense_fb = &rpisense->framebuffer;
-+
-+ rpisense_fb_param.vmem = vzalloc(rpisense_fb_param.vmemsize);
-+ if (!rpisense_fb_param.vmem)
-+ return ret;
-+
-+ rpisense_fb_param.vmem_work = devm_kmalloc(&pdev->dev, 193, GFP_KERNEL);
-+ if (!rpisense_fb_param.vmem_work)
-+ goto err_malloc;
-+
-+ info = framebuffer_alloc(0, &pdev->dev);
-+ if (!info) {
-+ dev_err(&pdev->dev, "Could not allocate framebuffer.\n");
-+ goto err_malloc;
-+ }
-+ rpisense_fb->info = info;
-+
-+ rpisense_fb_fix.smem_start = (unsigned long)rpisense_fb_param.vmem;
-+ rpisense_fb_fix.smem_len = rpisense_fb_param.vmemsize;
-+
-+ info->fbops = &rpisense_fb_ops;
-+ info->fix = rpisense_fb_fix;
-+ info->var = rpisense_fb_var;
-+ info->fbdefio = &rpisense_fb_defio;
-+ info->flags = FBINFO_FLAG_DEFAULT | FBINFO_VIRTFB;
-+ info->screen_base = rpisense_fb_param.vmem;
-+ info->screen_size = rpisense_fb_param.vmemsize;
-+
-+ if (lowlight)
-+ rpisense_fb_param.gamma = gamma_low;
-+
-+ fb_deferred_io_init(info);
-+
-+ ret = register_framebuffer(info);
-+ if (ret < 0) {
-+ dev_err(&pdev->dev, "Could not register framebuffer.\n");
-+ goto err_fballoc;
-+ }
-+
-+ fb_info(info, "%s frame buffer device\n", info->fix.id);
-+ schedule_delayed_work(&info->deferred_work, rpisense_fb_defio.delay);
-+ return 0;
-+err_fballoc:
-+ framebuffer_release(info);
-+err_malloc:
-+ vfree(rpisense_fb_param.vmem);
-+ return ret;
-+}
-+
-+static int rpisense_fb_remove(struct platform_device *pdev)
-+{
-+ struct rpisense_fb *rpisense_fb = &rpisense->framebuffer;
-+ struct fb_info *info = rpisense_fb->info;
-+
-+ if (info) {
-+ unregister_framebuffer(info);
-+ fb_deferred_io_cleanup(info);
-+ framebuffer_release(info);
-+ vfree(rpisense_fb_param.vmem);
-+ }
-+
-+ return 0;
-+}
-+
-+#ifdef CONFIG_OF
-+static const struct of_device_id rpisense_fb_id[] = {
-+ { .compatible = "rpi,rpi-sense-fb" },
-+ { },
-+};
-+MODULE_DEVICE_TABLE(of, rpisense_fb_id);
-+#endif
-+
-+static struct platform_device_id rpisense_fb_device_id[] = {
-+ { .name = "rpi-sense-fb" },
-+ { },
-+};
-+MODULE_DEVICE_TABLE(platform, rpisense_fb_device_id);
-+
-+static struct platform_driver rpisense_fb_driver = {
-+ .probe = rpisense_fb_probe,
-+ .remove = rpisense_fb_remove,
-+ .driver = {
-+ .name = "rpi-sense-fb",
-+ .owner = THIS_MODULE,
-+ },
-+};
-+
-+module_platform_driver(rpisense_fb_driver);
-+
-+MODULE_DESCRIPTION("Raspberry Pi Sense HAT framebuffer driver");
-+MODULE_AUTHOR("Serge Schneider <serge at raspberrypi.org>");
-+MODULE_LICENSE("GPL");
-+
---- /dev/null
-+++ b/include/linux/mfd/rpisense/core.h
-@@ -0,0 +1,47 @@
-+/*
-+ * Raspberry Pi Sense HAT core driver
-+ * http://raspberrypi.org
-+ *
-+ * Copyright (C) 2015 Raspberry Pi
-+ *
-+ * Author: Serge Schneider
-+ *
-+ * This program is free software; you can redistribute it and/or modify it
-+ * under the terms of the GNU General Public License as published by the
-+ * Free Software Foundation; either version 2 of the License, or (at your
-+ * option) any later version.
-+ *
-+ */
-+
-+#ifndef __LINUX_MFD_RPISENSE_CORE_H_
-+#define __LINUX_MFD_RPISENSE_CORE_H_
-+
-+#include <linux/mfd/rpisense/joystick.h>
-+#include <linux/mfd/rpisense/framebuffer.h>
-+
-+/*
-+ * Register values.
-+ */
-+#define RPISENSE_FB 0x00
-+#define RPISENSE_WAI 0xF0
-+#define RPISENSE_VER 0xF1
-+#define RPISENSE_KEYS 0xF2
-+#define RPISENSE_EE_WP 0xF3
-+
-+#define RPISENSE_ID 's'
-+
-+struct rpisense {
-+ struct device *dev;
-+ struct i2c_client *i2c_client;
-+
-+ /* Client devices */
-+ struct rpisense_js joystick;
-+ struct rpisense_fb framebuffer;
-+};
-+
-+struct rpisense *rpisense_get_dev(void);
-+s32 rpisense_reg_read(struct rpisense *rpisense, int reg);
-+int rpisense_reg_write(struct rpisense *rpisense, int reg, u16 val);
-+int rpisense_block_write(struct rpisense *rpisense, const char *buf, int count);
-+
-+#endif
---- /dev/null
-+++ b/include/linux/mfd/rpisense/framebuffer.h
-@@ -0,0 +1,32 @@
-+/*
-+ * Raspberry Pi Sense HAT framebuffer driver
-+ * http://raspberrypi.org
-+ *
-+ * Copyright (C) 2015 Raspberry Pi
-+ *
-+ * Author: Serge Schneider
-+ *
-+ * This program is free software; you can redistribute it and/or modify it
-+ * under the terms of the GNU General Public License as published by the
-+ * Free Software Foundation; either version 2 of the License, or (at your
-+ * option) any later version.
-+ *
-+ */
-+
-+#ifndef __LINUX_RPISENSE_FB_H_
-+#define __LINUX_RPISENSE_FB_H_
-+
-+#define SENSEFB_FBIO_IOC_MAGIC 0xF1
-+
-+#define SENSEFB_FBIOGET_GAMMA _IO(SENSEFB_FBIO_IOC_MAGIC, 0)
-+#define SENSEFB_FBIOSET_GAMMA _IO(SENSEFB_FBIO_IOC_MAGIC, 1)
-+#define SENSEFB_FBIORESET_GAMMA _IO(SENSEFB_FBIO_IOC_MAGIC, 2)
-+
-+struct rpisense;
-+
-+struct rpisense_fb {
-+ struct platform_device *pdev;
-+ struct fb_info *info;
-+};
-+
-+#endif
---- /dev/null
-+++ b/include/linux/mfd/rpisense/joystick.h
-@@ -0,0 +1,35 @@
-+/*
-+ * Raspberry Pi Sense HAT joystick driver
-+ * http://raspberrypi.org
-+ *
-+ * Copyright (C) 2015 Raspberry Pi
-+ *
-+ * Author: Serge Schneider
-+ *
-+ * This program is free software; you can redistribute it and/or modify it
-+ * under the terms of the GNU General Public License as published by the
-+ * Free Software Foundation; either version 2 of the License, or (at your
-+ * option) any later version.
-+ *
-+ */
-+
-+#ifndef __LINUX_RPISENSE_JOYSTICK_H_
-+#define __LINUX_RPISENSE_JOYSTICK_H_
-+
-+#include <linux/input.h>
-+#include <linux/interrupt.h>
-+#include <linux/gpio/consumer.h>
-+#include <linux/platform_device.h>
-+
-+struct rpisense;
-+
-+struct rpisense_js {
-+ struct platform_device *pdev;
-+ struct input_dev *keys_dev;
-+ struct gpio_desc *keys_desc;
-+ struct work_struct keys_work_s;
-+ int keys_irq;
-+};
-+
-+
-+#endif
diff --git a/target/linux/brcm2708/patches-4.4/0084-RaspiDAC3-support.patch b/target/linux/brcm2708/patches-4.4/0084-RaspiDAC3-support.patch
deleted file mode 100644
index a609c03..0000000
--- a/target/linux/brcm2708/patches-4.4/0084-RaspiDAC3-support.patch
+++ /dev/null
@@ -1,243 +0,0 @@
-From 8b344be12a4fce4565784ca77ffa55efed01cac4 Mon Sep 17 00:00:00 2001
-From: Jan Grulich <jan at grulich.eu>
-Date: Mon, 24 Aug 2015 16:03:47 +0100
-Subject: [PATCH] RaspiDAC3 support
-
-Signed-off-by: Jan Grulich <jan at grulich.eu>
-
-config: fix RaspiDAC Rev.3x dependencies
-
-Change depends to SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
-like the other I2S soundcard drivers.
-
-Signed-off-by: Matthias Reichl <hias at horus.com>
----
- sound/soc/bcm/Kconfig | 8 ++
- sound/soc/bcm/Makefile | 2 +
- sound/soc/bcm/raspidac3.c | 191 ++++++++++++++++++++++++++++++++++++++++++++++
- 3 files changed, 201 insertions(+)
- create mode 100644 sound/soc/bcm/raspidac3.c
-
---- a/sound/soc/bcm/Kconfig
-+++ b/sound/soc/bcm/Kconfig
-@@ -56,3 +56,11 @@ config SND_BCM2708_SOC_IQAUDIO_DAC
- select SND_SOC_PCM512x_I2C
- help
- Say Y or M if you want to add support for IQaudIO-DAC.
-+
-+config SND_BCM2708_SOC_RASPIDAC3
-+ tristate "Support for RaspiDAC Rev.3x"
-+ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
-+ select SND_SOC_PCM512x_I2C
-+ select SND_SOC_TPA6130A2
-+ help
-+ Say Y or M if you want to add support for RaspiDAC Rev.3x.
---- a/sound/soc/bcm/Makefile
-+++ b/sound/soc/bcm/Makefile
-@@ -11,6 +11,7 @@ snd-soc-hifiberry-amp-objs := hifiberry_
- snd-soc-rpi-dac-objs := rpi-dac.o
- snd-soc-rpi-proto-objs := rpi-proto.o
- snd-soc-iqaudio-dac-objs := iqaudio-dac.o
-+snd-soc-raspidac3-objs := raspidac3.o
-
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DAC) += snd-soc-hifiberry-dac.o
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DACPLUS) += snd-soc-hifiberry-dacplus.o
-@@ -19,3 +20,4 @@ obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_A
- obj-$(CONFIG_SND_BCM2708_SOC_RPI_DAC) += snd-soc-rpi-dac.o
- obj-$(CONFIG_SND_BCM2708_SOC_RPI_PROTO) += snd-soc-rpi-proto.o
- obj-$(CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC) += snd-soc-iqaudio-dac.o
-+obj-$(CONFIG_SND_BCM2708_SOC_RASPIDAC3) += snd-soc-raspidac3.o
---- /dev/null
-+++ b/sound/soc/bcm/raspidac3.c
-@@ -0,0 +1,191 @@
-+/*
-+ * ASoC Driver for RaspiDAC v3
-+ *
-+ * Author: Jan Grulich <jan at grulich.eu>
-+ * Copyright 2015
-+ * based on code by Daniel Matuschek <daniel at hifiberry.com>
-+ * based on code by Florian Meier <florian.meier at koalo.de>
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * version 2 as published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful, but
-+ * WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
-+ * General Public License for more details.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+
-+#include <sound/core.h>
-+#include <sound/pcm.h>
-+#include <sound/pcm_params.h>
-+#include <sound/soc.h>
-+#include <sound/jack.h>
-+#include <sound/soc-dapm.h>
-+
-+#include "../codecs/pcm512x.h"
-+#include "../codecs/tpa6130a2.h"
-+
-+/* sound card init */
-+static int snd_rpi_raspidac3_init(struct snd_soc_pcm_runtime *rtd)
-+{
-+ int ret;
-+ struct snd_soc_card *card = rtd->card;
-+ struct snd_soc_codec *codec = rtd->codec;
-+ snd_soc_update_bits(codec, PCM512x_GPIO_EN, 0x08, 0x08);
-+ snd_soc_update_bits(codec, PCM512x_GPIO_OUTPUT_4, 0xf, 0x02);
-+ snd_soc_update_bits(codec, PCM512x_GPIO_CONTROL_1, 0x08,0x00);
-+
-+ ret = snd_soc_limit_volume(card, "Digital Playback Volume", 207);
-+ if (ret < 0)
-+ dev_warn(card->dev, "Failed to set volume limit: %d\n", ret);
-+ else {
-+ struct snd_kcontrol *kctl;
-+
-+ ret = tpa6130a2_add_controls(codec);
-+ if (ret < 0)
-+ dev_warn(card->dev, "Failed to add TPA6130A2 controls: %d\n",
-+ ret);
-+ ret = snd_soc_limit_volume(card,
-+ "TPA6130A2 Headphone Playback Volume",
-+ 54);
-+ if (ret < 0)
-+ dev_warn(card->dev, "Failed to set TPA6130A2 volume limit: %d\n",
-+ ret);
-+ kctl = snd_soc_card_get_kcontrol(card,
-+ "TPA6130A2 Headphone Playback Volume");
-+ if (kctl) {
-+ strcpy(kctl->id.name, "Headphones Playback Volume");
-+ /* disable the volume dB scale so alsamixer works */
-+ kctl->vd[0].access = SNDRV_CTL_ELEM_ACCESS_READWRITE;
-+ }
-+
-+ kctl = snd_soc_card_get_kcontrol(card,
-+ "TPA6130A2 Headphone Playback Switch");
-+ if (kctl)
-+ strcpy(kctl->id.name, "Headphones Playback Switch");
-+ }
-+
-+ return 0;
-+}
-+
-+/* set hw parameters */
-+static int snd_rpi_raspidac3_hw_params(struct snd_pcm_substream *substream,
-+ struct snd_pcm_hw_params *params)
-+{
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
-+
-+ unsigned int sample_bits =
-+ snd_pcm_format_physical_width(params_format(params));
-+
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, sample_bits * 2);
-+}
-+
-+/* startup */
-+static int snd_rpi_raspidac3_startup(struct snd_pcm_substream *substream) {
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_codec *codec = rtd->codec;
-+ snd_soc_update_bits(codec, PCM512x_GPIO_CONTROL_1, 0x08,0x08);
-+ tpa6130a2_stereo_enable(codec, 1);
-+ return 0;
-+}
-+
-+/* shutdown */
-+static void snd_rpi_raspidac3_shutdown(struct snd_pcm_substream *substream) {
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_codec *codec = rtd->codec;
-+ snd_soc_update_bits(codec, PCM512x_GPIO_CONTROL_1, 0x08,0x00);
-+ tpa6130a2_stereo_enable(codec, 0);
-+}
-+
-+/* machine stream operations */
-+static struct snd_soc_ops snd_rpi_raspidac3_ops = {
-+ .hw_params = snd_rpi_raspidac3_hw_params,
-+ .startup = snd_rpi_raspidac3_startup,
-+ .shutdown = snd_rpi_raspidac3_shutdown,
-+};
-+
-+/* interface setup */
-+static struct snd_soc_dai_link snd_rpi_raspidac3_dai[] = {
-+{
-+ .name = "RaspiDAC Rev.3x",
-+ .stream_name = "RaspiDAC HiFi",
-+ .cpu_dai_name = "bcm2708-i2s.0",
-+ .codec_dai_name = "pcm512x-hifi",
-+ .platform_name = "bcm2708-i2s.0",
-+ .codec_name = "pcm512x.1-004c",
-+ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF |
-+ SND_SOC_DAIFMT_CBS_CFS,
-+ .ops = &snd_rpi_raspidac3_ops,
-+ .init = snd_rpi_raspidac3_init,
-+},
-+};
-+
-+/* audio machine driver */
-+static struct snd_soc_card snd_rpi_raspidac3 = {
-+ .name = "RaspiDAC Rev.3x HiFi Audio Card",
-+ .dai_link = snd_rpi_raspidac3_dai,
-+ .num_links = ARRAY_SIZE(snd_rpi_raspidac3_dai),
-+};
-+
-+/* sound card test */
-+static int snd_rpi_raspidac3_probe(struct platform_device *pdev)
-+{
-+ int ret = 0;
-+
-+ snd_rpi_raspidac3.dev = &pdev->dev;
-+
-+ if (pdev->dev.of_node) {
-+ struct device_node *i2s_node;
-+ struct snd_soc_dai_link *dai = &snd_rpi_raspidac3_dai[0];
-+ i2s_node = of_parse_phandle(pdev->dev.of_node,
-+ "i2s-controller", 0);
-+
-+ if (i2s_node) {
-+ dai->cpu_dai_name = NULL;
-+ dai->cpu_of_node = i2s_node;
-+ dai->platform_name = NULL;
-+ dai->platform_of_node = i2s_node;
-+ }
-+ }
-+
-+ ret = snd_soc_register_card(&snd_rpi_raspidac3);
-+ if (ret)
-+ dev_err(&pdev->dev,
-+ "snd_soc_register_card() failed: %d\n", ret);
-+
-+ return ret;
-+}
-+
-+/* sound card disconnect */
-+static int snd_rpi_raspidac3_remove(struct platform_device *pdev)
-+{
-+ return snd_soc_unregister_card(&snd_rpi_raspidac3);
-+}
-+
-+static const struct of_device_id raspidac3_of_match[] = {
-+ { .compatible = "jg,raspidacv3", },
-+ {},
-+};
-+MODULE_DEVICE_TABLE(of, raspidac3_of_match);
-+
-+/* sound card platform driver */
-+static struct platform_driver snd_rpi_raspidac3_driver = {
-+ .driver = {
-+ .name = "snd-rpi-raspidac3",
-+ .owner = THIS_MODULE,
-+ .of_match_table = raspidac3_of_match,
-+ },
-+ .probe = snd_rpi_raspidac3_probe,
-+ .remove = snd_rpi_raspidac3_remove,
-+};
-+
-+module_platform_driver(snd_rpi_raspidac3_driver);
-+
-+MODULE_AUTHOR("Jan Grulich <jan at grulich.eu>");
-+MODULE_DESCRIPTION("ASoC Driver for RaspiDAC Rev.3x");
-+MODULE_LICENSE("GPL v2");
diff --git a/target/linux/brcm2708/patches-4.4/0085-tpa6130a2-Add-headphone-switch-control.patch b/target/linux/brcm2708/patches-4.4/0085-tpa6130a2-Add-headphone-switch-control.patch
deleted file mode 100644
index 457cc9d..0000000
--- a/target/linux/brcm2708/patches-4.4/0085-tpa6130a2-Add-headphone-switch-control.patch
+++ /dev/null
@@ -1,91 +0,0 @@
-From 85e81afc181bb6ae8ad75723b9f2fc40db1041f2 Mon Sep 17 00:00:00 2001
-From: Jan Grulich <jan at grulich.eu>
-Date: Mon, 24 Aug 2015 16:02:34 +0100
-Subject: [PATCH] tpa6130a2: Add headphone switch control
-
-Signed-off-by: Jan Grulich <jan at grulich.eu>
----
- sound/soc/codecs/tpa6130a2.c | 29 ++++++++++++++++++++++++++---
- 1 file changed, 26 insertions(+), 3 deletions(-)
-
---- a/sound/soc/codecs/tpa6130a2.c
-+++ b/sound/soc/codecs/tpa6130a2.c
-@@ -4,6 +4,7 @@
- * Copyright (C) Nokia Corporation
- *
- * Author: Peter Ujfalusi <peter.ujfalusi at ti.com>
-+ * Modified: Jan Grulich <jan at grulich.eu>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
-@@ -52,6 +53,8 @@ struct tpa6130a2_data {
- enum tpa_model id;
- };
-
-+static void tpa6130a2_channel_enable(u8 channel, int enable);
-+
- static int tpa6130a2_i2c_read(int reg)
- {
- struct tpa6130a2_data *data;
-@@ -189,7 +192,7 @@ exit:
- }
-
- static int tpa6130a2_get_volsw(struct snd_kcontrol *kcontrol,
-- struct snd_ctl_elem_value *ucontrol)
-+ struct snd_ctl_elem_value *ucontrol)
- {
- struct soc_mixer_control *mc =
- (struct soc_mixer_control *)kcontrol->private_value;
-@@ -218,7 +221,7 @@ static int tpa6130a2_get_volsw(struct sn
- }
-
- static int tpa6130a2_put_volsw(struct snd_kcontrol *kcontrol,
-- struct snd_ctl_elem_value *ucontrol)
-+ struct snd_ctl_elem_value *ucontrol)
- {
- struct soc_mixer_control *mc =
- (struct soc_mixer_control *)kcontrol->private_value;
-@@ -255,8 +258,22 @@ static int tpa6130a2_put_volsw(struct sn
- return 1;
- }
-
-+static int tpa6130a2_put_hp_sw(struct snd_kcontrol *kcontrol,
-+ struct snd_ctl_elem_value *ucontrol)
-+{
-+ int enable = ucontrol->value.integer.value[0];
-+ unsigned int state;
-+
-+ state = (tpa6130a2_read(TPA6130A2_REG_VOL_MUTE) & 0x80) == 0;
-+ if (state == enable)
-+ return 0; /* No change */
-+
-+ tpa6130a2_channel_enable(TPA6130A2_HP_EN_R | TPA6130A2_HP_EN_L, enable);
-+ return 1; /* Changed */
-+}
-+
- /*
-- * TPA6130 volume. From -59.5 to 4 dB with increasing step size when going
-+ * TPA6130 volume. From -59.5 to +4.0 dB with increasing step size when going
- * down in gain.
- */
- static const DECLARE_TLV_DB_RANGE(tpa6130_tlv,
-@@ -277,6 +294,9 @@ static const struct snd_kcontrol_new tpa
- TPA6130A2_REG_VOL_MUTE, 0, 0x3f, 0,
- tpa6130a2_get_volsw, tpa6130a2_put_volsw,
- tpa6130_tlv),
-+ SOC_SINGLE_EXT("TPA6130A2 Headphone Playback Switch",
-+ TPA6130A2_REG_VOL_MUTE, 7, 1, 1,
-+ tpa6130a2_get_volsw, tpa6130a2_put_hp_sw),
- };
-
- static const DECLARE_TLV_DB_RANGE(tpa6140_tlv,
-@@ -290,6 +310,9 @@ static const struct snd_kcontrol_new tpa
- TPA6130A2_REG_VOL_MUTE, 1, 0x1f, 0,
- tpa6130a2_get_volsw, tpa6130a2_put_volsw,
- tpa6140_tlv),
-+ SOC_SINGLE_EXT("TPA6140A2 Headphone Playback Switch",
-+ TPA6130A2_REG_VOL_MUTE, 7, 1, 1,
-+ tpa6130a2_get_volsw, tpa6130a2_put_hp_sw),
- };
-
- /*
diff --git a/target/linux/brcm2708/patches-4.4/0086-irq-bcm2835-Fix-building-with-2708.patch b/target/linux/brcm2708/patches-4.4/0086-irq-bcm2835-Fix-building-with-2708.patch
deleted file mode 100644
index 4aa956b..0000000
--- a/target/linux/brcm2708/patches-4.4/0086-irq-bcm2835-Fix-building-with-2708.patch
+++ /dev/null
@@ -1,28 +0,0 @@
-From e0230a20a5c53115b119b80d1332a81b61991110 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Mon, 28 Sep 2015 23:38:59 +0100
-Subject: [PATCH] irq-bcm2835: Fix building with 2708
-
----
- drivers/irqchip/irq-bcm2835.c | 3 ++-
- 1 file changed, 2 insertions(+), 1 deletion(-)
-
---- a/drivers/irqchip/irq-bcm2835.c
-+++ b/drivers/irqchip/irq-bcm2835.c
-@@ -82,6 +82,7 @@
- #define NR_BANKS 3
- #define IRQS_PER_BANK 32
- #define NUMBER_IRQS MAKE_HWIRQ(NR_BANKS, 0)
-+#undef FIQ_START
- #define FIQ_START (NR_IRQS_BANK0 + MAKE_HWIRQ(NR_BANKS - 1, 0))
-
- static const int reg_pending[] __initconst = { 0x00, 0x04, 0x08 };
-@@ -256,7 +257,7 @@ static int __init armctrl_of_init(struct
- MAKE_HWIRQ(b, i) + NUMBER_IRQS);
- BUG_ON(irq <= 0);
- irq_set_chip(irq, &armctrl_chip);
-- set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
-+ irq_set_probe(irq);
- }
- }
- init_FIQ(FIQ_START);
diff --git a/target/linux/brcm2708/patches-4.4/0087-rpi_display-add-backlight-driver-and-overlay.patch b/target/linux/brcm2708/patches-4.4/0087-rpi_display-add-backlight-driver-and-overlay.patch
deleted file mode 100644
index 9c159df..0000000
--- a/target/linux/brcm2708/patches-4.4/0087-rpi_display-add-backlight-driver-and-overlay.patch
+++ /dev/null
@@ -1,250 +0,0 @@
-From bd99bf8c59e9cfa39c8237e5852c51bff853e1e9 Mon Sep 17 00:00:00 2001
-From: P33M <P33M at github.com>
-Date: Wed, 21 Oct 2015 14:55:21 +0100
-Subject: [PATCH] rpi_display: add backlight driver and overlay
-
-Add a mailbox-driven backlight controller for the Raspberry Pi DSI
-touchscreen display. Requires updated GPU firmware to recognise the
-mailbox request.
-
-Signed-off-by: Gordon Hollingworth <gordon at raspberrypi.org>
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 6 ++
- .../boot/dts/overlays/rpi-backlight-overlay.dts | 21 ++++
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- drivers/video/backlight/Kconfig | 6 ++
- drivers/video/backlight/Makefile | 1 +
- drivers/video/backlight/rpi_backlight.c | 119 +++++++++++++++++++++
- include/soc/bcm2835/raspberrypi-firmware.h | 1 +
- 9 files changed, 157 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/rpi-backlight-overlay.dts
- create mode 100644 drivers/video/backlight/rpi_backlight.c
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -38,6 +38,7 @@ dtb-$(RPI_DT_OVERLAYS) += pps-gpio-overl
- dtb-$(RPI_DT_OVERLAYS) += pwm-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += pwm-2chan-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += raspidac3-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += rpi-backlight-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += rpi-dac-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += rpi-display-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += rpi-ft5406-overlay.dtb
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -462,6 +462,12 @@ Load: dtoverlay=raspidac3
- Params: <None>
-
-
-+Name: rpi-backlight
-+Info: Raspberry Pi official display backlight driver
-+Load: dtoverlay=rpi-backlight
-+Params: <None>
-+
-+
- Name: rpi-dac
- Info: Configures the RPi DAC audio card
- Load: dtoverlay=rpi-dac
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/rpi-backlight-overlay.dts
-@@ -0,0 +1,21 @@
-+/*
-+ * Devicetree overlay for mailbox-driven Raspberry Pi DSI Display
-+ * backlight controller
-+ */
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target-path = "/";
-+ __overlay__ {
-+ rpi_backlight: rpi_backlight {
-+ compatible = "raspberrypi,rpi-backlight";
-+ firmware = <&firmware>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+};
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -808,6 +808,7 @@ CONFIG_FB_UDL=m
- CONFIG_FB_SSD1307=m
- CONFIG_FB_RPISENSE=m
- # CONFIG_BACKLIGHT_GENERIC is not set
-+CONFIG_BACKLIGHT_RPI=m
- CONFIG_BACKLIGHT_GPIO=m
- CONFIG_FRAMEBUFFER_CONSOLE=y
- CONFIG_LOGO=y
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -801,6 +801,7 @@ CONFIG_FB_UDL=m
- CONFIG_FB_SSD1307=m
- CONFIG_FB_RPISENSE=m
- # CONFIG_BACKLIGHT_GENERIC is not set
-+CONFIG_BACKLIGHT_RPI=m
- CONFIG_BACKLIGHT_GPIO=m
- CONFIG_FRAMEBUFFER_CONSOLE=y
- CONFIG_LOGO=y
---- a/drivers/video/backlight/Kconfig
-+++ b/drivers/video/backlight/Kconfig
-@@ -265,6 +265,12 @@ config BACKLIGHT_PWM
- If you have a LCD backlight adjustable by PWM, say Y to enable
- this driver.
-
-+config BACKLIGHT_RPI
-+ tristate "Raspberry Pi display firmware driven backlight"
-+ help
-+ If you have the Raspberry Pi DSI touchscreen display, say Y to
-+ enable the mailbox-controlled backlight driver.
-+
- config BACKLIGHT_DA903X
- tristate "Backlight Driver for DA9030/DA9034 using WLED"
- depends on PMIC_DA903X
---- a/drivers/video/backlight/Makefile
-+++ b/drivers/video/backlight/Makefile
-@@ -50,6 +50,7 @@ obj-$(CONFIG_BACKLIGHT_PANDORA) += pand
- obj-$(CONFIG_BACKLIGHT_PCF50633) += pcf50633-backlight.o
- obj-$(CONFIG_BACKLIGHT_PM8941_WLED) += pm8941-wled.o
- obj-$(CONFIG_BACKLIGHT_PWM) += pwm_bl.o
-+obj-$(CONFIG_BACKLIGHT_RPI) += rpi_backlight.o
- obj-$(CONFIG_BACKLIGHT_SAHARA) += kb3886_bl.o
- obj-$(CONFIG_BACKLIGHT_SKY81452) += sky81452-backlight.o
- obj-$(CONFIG_BACKLIGHT_TOSA) += tosa_bl.o
---- /dev/null
-+++ b/drivers/video/backlight/rpi_backlight.c
-@@ -0,0 +1,119 @@
-+/*
-+ * rpi_bl.c - Backlight controller through VPU
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ */
-+
-+#include <linux/backlight.h>
-+#include <linux/err.h>
-+#include <linux/fb.h>
-+#include <linux/gpio.h>
-+#include <linux/init.h>
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+#include <linux/of.h>
-+#include <linux/of_gpio.h>
-+#include <linux/platform_device.h>
-+#include <linux/slab.h>
-+#include <soc/bcm2835/raspberrypi-firmware.h>
-+
-+struct rpi_backlight {
-+ struct device *dev;
-+ struct device *fbdev;
-+ struct rpi_firmware *fw;
-+};
-+
-+static int rpi_backlight_update_status(struct backlight_device *bl)
-+{
-+ struct rpi_backlight *gbl = bl_get_data(bl);
-+ int brightness = bl->props.brightness;
-+ int ret;
-+
-+ if (bl->props.power != FB_BLANK_UNBLANK ||
-+ bl->props.fb_blank != FB_BLANK_UNBLANK ||
-+ bl->props.state & (BL_CORE_SUSPENDED | BL_CORE_FBBLANK))
-+ brightness = 0;
-+
-+ ret = rpi_firmware_property(gbl->fw,
-+ RPI_FIRMWARE_FRAMEBUFFER_SET_BACKLIGHT,
-+ &brightness, sizeof(brightness));
-+ if (ret) {
-+ dev_err(gbl->dev, "Failed to set brightness\n");
-+ return ret;
-+ }
-+
-+ if (brightness < 0) {
-+ dev_err(gbl->dev, "Backlight change failed\n");
-+ return -EAGAIN;
-+ }
-+
-+ return 0;
-+}
-+
-+static const struct backlight_ops rpi_backlight_ops = {
-+ .options = BL_CORE_SUSPENDRESUME,
-+ .update_status = rpi_backlight_update_status,
-+};
-+
-+static int rpi_backlight_probe(struct platform_device *pdev)
-+{
-+ struct backlight_properties props;
-+ struct backlight_device *bl;
-+ struct rpi_backlight *gbl;
-+ struct device_node *fw_node;
-+
-+ gbl = devm_kzalloc(&pdev->dev, sizeof(*gbl), GFP_KERNEL);
-+ if (gbl == NULL)
-+ return -ENOMEM;
-+
-+ gbl->dev = &pdev->dev;
-+
-+ fw_node = of_parse_phandle(pdev->dev.of_node, "firmware", 0);
-+ if (!fw_node) {
-+ dev_err(&pdev->dev, "Missing firmware node\n");
-+ return -ENOENT;
-+ }
-+
-+ gbl->fw = rpi_firmware_get(fw_node);
-+ if (!gbl->fw)
-+ return -EPROBE_DEFER;
-+
-+ memset(&props, 0, sizeof(props));
-+ props.type = BACKLIGHT_RAW;
-+ props.max_brightness = 255;
-+ bl = devm_backlight_device_register(&pdev->dev, dev_name(&pdev->dev),
-+ &pdev->dev, gbl, &rpi_backlight_ops,
-+ &props);
-+ if (IS_ERR(bl)) {
-+ dev_err(&pdev->dev, "failed to register backlight\n");
-+ return PTR_ERR(bl);
-+ }
-+
-+ bl->props.brightness = 255;
-+ backlight_update_status(bl);
-+
-+ platform_set_drvdata(pdev, bl);
-+ return 0;
-+}
-+
-+static const struct of_device_id rpi_backlight_of_match[] = {
-+ { .compatible = "raspberrypi,rpi-backlight" },
-+ { /* sentinel */ }
-+};
-+MODULE_DEVICE_TABLE(of, rpi_backlight_of_match);
-+
-+static struct platform_driver rpi_backlight_driver = {
-+ .driver = {
-+ .name = "rpi-backlight",
-+ .of_match_table = of_match_ptr(rpi_backlight_of_match),
-+ },
-+ .probe = rpi_backlight_probe,
-+};
-+
-+module_platform_driver(rpi_backlight_driver);
-+
-+MODULE_AUTHOR("Gordon Hollingworth <gordon at raspberrypi.org>");
-+MODULE_DESCRIPTION("Raspberry Pi mailbox based Backlight Driver");
-+MODULE_LICENSE("GPL");
---- a/include/soc/bcm2835/raspberrypi-firmware.h
-+++ b/include/soc/bcm2835/raspberrypi-firmware.h
-@@ -112,6 +112,7 @@ enum rpi_firmware_property_tag {
- RPI_FIRMWARE_FRAMEBUFFER_SET_OVERSCAN = 0x0004800a,
- RPI_FIRMWARE_FRAMEBUFFER_SET_PALETTE = 0x0004800b,
- RPI_FIRMWARE_FRAMEBUFFER_SET_VSYNC = 0x0004800e,
-+ RPI_FIRMWARE_FRAMEBUFFER_SET_BACKLIGHT = 0x0004800f,
-
- RPI_FIRMWARE_VCHIQ_INIT = 0x00048010,
-
diff --git a/target/linux/brcm2708/patches-4.4/0088-bcm2835-dma-Fix-up-convert-to-DMA-pool.patch b/target/linux/brcm2708/patches-4.4/0088-bcm2835-dma-Fix-up-convert-to-DMA-pool.patch
deleted file mode 100644
index 10c6bac..0000000
--- a/target/linux/brcm2708/patches-4.4/0088-bcm2835-dma-Fix-up-convert-to-DMA-pool.patch
+++ /dev/null
@@ -1,85 +0,0 @@
-From 4c9c5dfadea113fded74c2ab29f96b2109abaa04 Mon Sep 17 00:00:00 2001
-From: Matthias Reichl <hias at horus.com>
-Date: Mon, 16 Nov 2015 14:05:35 +0000
-Subject: [PATCH] bcm2835-dma: Fix up convert to DMA pool
-
----
- drivers/dma/bcm2835-dma.c | 36 ++++++++++++++++++++++++++----------
- 1 file changed, 26 insertions(+), 10 deletions(-)
-
---- a/drivers/dma/bcm2835-dma.c
-+++ b/drivers/dma/bcm2835-dma.c
-@@ -488,6 +488,17 @@ static struct dma_async_tx_descriptor *b
- c->cyclic = true;
-
- return vchan_tx_prep(&c->vc, &d->vd, flags);
-+error_cb:
-+ i--;
-+ for (; i >= 0; i--) {
-+ struct bcm2835_cb_entry *cb_entry = &d->cb_list[i];
-+
-+ dma_pool_free(c->cb_pool, cb_entry->cb, cb_entry->paddr);
-+ }
-+
-+ kfree(d->cb_list);
-+ kfree(d);
-+ return NULL;
- }
-
- static struct dma_async_tx_descriptor *
-@@ -534,6 +545,7 @@ bcm2835_dma_prep_slave_sg(struct dma_cha
- if (!d)
- return NULL;
-
-+ d->c = c;
- d->dir = direction;
-
- if (c->ch >= 8) /* LITE channel */
-@@ -553,15 +565,21 @@ bcm2835_dma_prep_slave_sg(struct dma_cha
- d->frames += len / max_size + 1;
- }
-
-- /* Allocate memory for control blocks */
-- d->control_block_size = d->frames * sizeof(struct bcm2835_dma_cb);
-- d->control_block_base = dma_zalloc_coherent(chan->device->dev,
-- d->control_block_size, &d->control_block_base_phys,
-- GFP_NOWAIT);
-- if (!d->control_block_base) {
-+ d->cb_list = kcalloc(d->frames, sizeof(*d->cb_list), GFP_KERNEL);
-+ if (!d->cb_list) {
- kfree(d);
- return NULL;
- }
-+ /* Allocate memory for control blocks */
-+ for (i = 0; i < d->frames; i++) {
-+ struct bcm2835_cb_entry *cb_entry = &d->cb_list[i];
-+
-+ cb_entry->cb = dma_pool_zalloc(c->cb_pool, GFP_ATOMIC,
-+ &cb_entry->paddr);
-+
-+ if (!cb_entry->cb)
-+ goto error_cb;
-+ }
-
- /*
- * Iterate over all SG entries, create a control block
-@@ -578,7 +596,7 @@ bcm2835_dma_prep_slave_sg(struct dma_cha
-
- for (j = 0; j < len; j += max_size) {
- struct bcm2835_dma_cb *control_block =
-- &d->control_block_base[i + split_cnt];
-+ d->cb_list[i + split_cnt].cb;
-
- /* Setup addresses */
- if (d->dir == DMA_DEV_TO_MEM) {
-@@ -620,9 +638,7 @@ bcm2835_dma_prep_slave_sg(struct dma_cha
- if (i < sg_len - 1 || len - j > max_size) {
- /* Next block is the next frame. */
- control_block->next =
-- d->control_block_base_phys +
-- sizeof(struct bcm2835_dma_cb) *
-- (i + split_cnt + 1);
-+ d->cb_list[i + split_cnt + 1].paddr;
- } else {
- /* Next block is empty. */
- control_block->next = 0;
diff --git a/target/linux/brcm2708/patches-4.4/0089-scripts-Multi-platform-support-for-mkknlimg-and-knli.patch b/target/linux/brcm2708/patches-4.4/0089-scripts-Multi-platform-support-for-mkknlimg-and-knli.patch
deleted file mode 100644
index 2aff538..0000000
--- a/target/linux/brcm2708/patches-4.4/0089-scripts-Multi-platform-support-for-mkknlimg-and-knli.patch
+++ /dev/null
@@ -1,246 +0,0 @@
-From 0fda3a1eb42445783633e477f261575222c3470b Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Wed, 11 Nov 2015 11:38:59 +0000
-Subject: [PATCH] scripts: Multi-platform support for mkknlimg and knlinfo
-
-The firmware uses tags in the kernel trailer to choose which dtb file
-to load. Current firmware loads bcm2835-*.dtb if the '283x' tag is true,
-otherwise it loads bcm270*.dtb. This scheme breaks if an image supports
-multiple platforms.
-
-This patch adds '270X' and '283X' tags to indicate support for RPi and
-upstream platforms, respectively. '283x' (note lower case 'x') is left
-for old firmware, and is only set if the image only supports upstream
-builds.
----
- scripts/knlinfo | 2 +
- scripts/mkknlimg | 136 +++++++++++++++++++++++++++++++------------------------
- 2 files changed, 80 insertions(+), 58 deletions(-)
-
---- a/scripts/knlinfo
-+++ b/scripts/knlinfo
-@@ -18,6 +18,8 @@ my %atom_formats =
- (
- 'DTOK' => \&format_bool,
- 'KVer' => \&format_string,
-+ '270X' => \&format_bool,
-+ '283X' => \&format_bool,
- '283x' => \&format_bool,
- );
-
---- a/scripts/mkknlimg
-+++ b/scripts/mkknlimg
-@@ -13,12 +13,20 @@ use strict;
- use warnings;
- use integer;
-
-+use constant FLAG_PI => 0x01;
-+use constant FLAG_DTOK => 0x02;
-+use constant FLAG_DDTK => 0x04;
-+use constant FLAG_270X => 0x08;
-+use constant FLAG_283X => 0x10;
-+
- my $trailer_magic = 'RPTL';
-
- my $tmpfile1 = "/tmp/mkknlimg_$$.1";
- my $tmpfile2 = "/tmp/mkknlimg_$$.2";
-
- my $dtok = 0;
-+my $ddtk = 0;
-+my $is_270x = 0;
- my $is_283x = 0;
-
- while (@ARGV && ($ARGV[0] =~ /^-/))
-@@ -28,6 +36,14 @@ while (@ARGV && ($ARGV[0] =~ /^-/))
- {
- $dtok = 1;
- }
-+ elsif ($arg eq '--ddtk')
-+ {
-+ $ddtk = 1;
-+ }
-+ elsif ($arg eq '--270x')
-+ {
-+ $is_270x = 1;
-+ }
- elsif ($arg eq '--283x')
- {
- $is_283x = 1;
-@@ -50,30 +66,33 @@ if (! -r $kernel_file)
- usage();
- }
-
--my @wanted_strings =
--(
-- 'bcm2708_fb',
-- 'brcm,bcm2835-mmc',
-- 'brcm,bcm2835-sdhost',
-- 'brcm,bcm2708-pinctrl',
-- 'brcm,bcm2835-gpio',
-- 'brcm,bcm2835',
-- 'brcm,bcm2836'
--);
-+my $wanted_strings =
-+{
-+ 'bcm2708_fb' => FLAG_PI,
-+ 'brcm,bcm2835-mmc' => FLAG_PI,
-+ 'brcm,bcm2835-sdhost' => FLAG_PI,
-+ 'brcm,bcm2708-pinctrl' => FLAG_PI | FLAG_DTOK,
-+ 'brcm,bcm2835-gpio' => FLAG_PI | FLAG_DTOK,
-+ 'brcm,bcm2708' => FLAG_PI | FLAG_DTOK | FLAG_270X,
-+ 'brcm,bcm2709' => FLAG_PI | FLAG_DTOK | FLAG_270X,
-+ 'brcm,bcm2835' => FLAG_PI | FLAG_DTOK | FLAG_283X,
-+ 'brcm,bcm2836' => FLAG_PI | FLAG_DTOK | FLAG_283X,
-+ 'of_overlay_apply' => FLAG_DTOK | FLAG_DDTK,
-+};
-
- my $res = try_extract($kernel_file, $tmpfile1);
--$res = try_decompress('\037\213\010', 'xy', 'gunzip', 0,
-- $kernel_file, $tmpfile1, $tmpfile2) if (!$res);
--$res = try_decompress('\3757zXZ\000', 'abcde', 'unxz --single-stream', -1,
-- $kernel_file, $tmpfile1, $tmpfile2) if (!$res);
--$res = try_decompress('BZh', 'xy', 'bunzip2', 0,
-- $kernel_file, $tmpfile1, $tmpfile2) if (!$res);
--$res = try_decompress('\135\0\0\0', 'xxx', 'unlzma', 0,
-- $kernel_file, $tmpfile1, $tmpfile2) if (!$res);
--$res = try_decompress('\211\114\132', 'xy', 'lzop -d', 0,
-- $kernel_file, $tmpfile1, $tmpfile2) if (!$res);
--$res = try_decompress('\002\041\114\030', 'xy', 'lz4 -d', 1,
-- $kernel_file, $tmpfile1, $tmpfile2) if (!$res);
-+$res ||= try_decompress('\037\213\010', 'xy', 'gunzip', 0,
-+ $kernel_file, $tmpfile1, $tmpfile2);
-+$res ||= try_decompress('\3757zXZ\000', 'abcde', 'unxz --single-stream', -1,
-+ $kernel_file, $tmpfile1, $tmpfile2);
-+$res ||= try_decompress('BZh', 'xy', 'bunzip2', 0,
-+ $kernel_file, $tmpfile1, $tmpfile2);
-+$res ||= try_decompress('\135\0\0\0', 'xxx', 'unlzma', 0,
-+ $kernel_file, $tmpfile1, $tmpfile2);
-+$res ||= try_decompress('\211\114\132', 'xy', 'lzop -d', 0,
-+ $kernel_file, $tmpfile1, $tmpfile2);
-+$res ||= try_decompress('\002\041\114\030', 'xy', 'lz4 -d', 1,
-+ $kernel_file, $tmpfile1, $tmpfile2);
-
- my $append_trailer;
- my $trailer;
-@@ -83,27 +102,21 @@ $append_trailer = $dtok;
-
- if ($res)
- {
-- $kver = $res->{''} || '?';
-+ $kver = $res->{'kver'} || '?';
-+ my $flags = $res->{'flags'};
- print("Version: $kver\n");
-
-- $append_trailer = $dtok;
-- if (!$dtok)
-+ if ($flags & FLAG_PI)
- {
-- if (config_bool($res, 'bcm2708_fb') ||
-- config_bool($res, 'brcm,bcm2835-mmc') ||
-- config_bool($res, 'brcm,bcm2835-sdhost'))
-- {
-- $dtok ||= config_bool($res, 'brcm,bcm2708-pinctrl');
-- $dtok ||= config_bool($res, 'brcm,bcm2835-gpio');
-- $is_283x ||= config_bool($res, 'brcm,bcm2835');
-- $is_283x ||= config_bool($res, 'brcm,bcm2836');
-- $dtok ||= $is_283x;
-- $append_trailer = 1;
-- }
-- else
-- {
-- print ("* This doesn't look like a Raspberry Pi kernel. In pass-through mode.\n");
-- }
-+ $append_trailer = 1;
-+ $dtok ||= ($flags & FLAG_DTOK) != 0;
-+ $is_270x ||= ($flags & FLAG_270X) != 0;
-+ $is_283x ||= ($flags & FLAG_283X) != 0;
-+ $ddtk ||= ($flags & FLAG_DDTK) != 0;
-+ }
-+ else
-+ {
-+ print ("* This doesn't look like a Raspberry Pi kernel. In pass-through mode.\n");
- }
- }
- elsif (!$dtok)
-@@ -114,6 +127,8 @@ elsif (!$dtok)
- if ($append_trailer)
- {
- printf("DT: %s\n", $dtok ? "y" : "n");
-+ printf("DDT: %s\n", $ddtk ? "y" : "n") if ($ddtk);
-+ printf("270x: %s\n", $is_270x ? "y" : "n");
- printf("283x: %s\n", $is_283x ? "y" : "n");
-
- my @atoms;
-@@ -121,7 +136,10 @@ if ($append_trailer)
- push @atoms, [ $trailer_magic, pack('V', 0) ];
- push @atoms, [ 'KVer', $kver ];
- push @atoms, [ 'DTOK', pack('V', $dtok) ];
-- push @atoms, [ '283x', pack('V', $is_283x) ];
-+ push @atoms, [ 'DDTK', pack('V', $ddtk) ] if ($ddtk);
-+ push @atoms, [ '270X', pack('V', $is_270x) ];
-+ push @atoms, [ '283X', pack('V', $is_283x) ];
-+ push @atoms, [ '283x', pack('V', $is_283x && !$is_270x) ];
-
- $trailer = pack_trailer(\@atoms);
- $atoms[0]->[1] = pack('V', length($trailer));
-@@ -175,7 +193,7 @@ END {
-
- sub usage
- {
-- print ("Usage: mkknlimg [--dtok] [--283x] <vmlinux|zImage|bzImage> <outfile>\n");
-+ print ("Usage: mkknlimg [--dtok] [--270x] [--283x] <vmlinux|zImage|bzImage> <outfile>\n");
- exit(1);
- }
-
-@@ -189,15 +207,8 @@ sub try_extract
-
- chomp($ver);
-
-- my $res = { ''=>$ver };
-- my $string_pattern = '^('.join('|', @wanted_strings).')$';
--
-- my @matches = `strings \"$knl\" | grep -E \"$string_pattern\"`;
-- foreach my $match (@matches)
-- {
-- chomp($match);
-- $res->{$match} = 1;
-- }
-+ my $res = { 'kver'=>$ver };
-+ $res->{'flags'} = strings_to_flags($knl, $wanted_strings);
-
- return $res;
- }
-@@ -224,6 +235,22 @@ sub try_decompress
- return undef;
- }
-
-+sub strings_to_flags
-+{
-+ my ($knl, $strings) = @_;
-+ my $string_pattern = '^('.join('|', keys(%$strings)).')$';
-+ my $flags = 0;
-+
-+ my @matches = `strings \"$knl\" | grep -E \"$string_pattern\"`;
-+ foreach my $match (@matches)
-+ {
-+ chomp($match);
-+ $flags |= $strings->{$match};
-+ }
-+
-+ return $flags;
-+}
-+
- sub pack_trailer
- {
- my ($atoms) = @_;
-@@ -235,10 +262,3 @@ sub pack_trailer
- }
- return $trailer;
- }
--
--sub config_bool
--{
-- my ($configs, $wanted) = @_;
-- my $val = $configs->{$wanted} || 'n';
-- return (($val eq 'y') || ($val eq '1'));
--}
diff --git a/target/linux/brcm2708/patches-4.4/0090-drm-vc4-Add-suport-for-3D-rendering-using-the-V3D-en.patch b/target/linux/brcm2708/patches-4.4/0090-drm-vc4-Add-suport-for-3D-rendering-using-the-V3D-en.patch
deleted file mode 100644
index 95ff05e..0000000
--- a/target/linux/brcm2708/patches-4.4/0090-drm-vc4-Add-suport-for-3D-rendering-using-the-V3D-en.patch
+++ /dev/null
@@ -1,5557 +0,0 @@
-From 2a921dd7c2e9455579186a1cc0ff60f1ec21b652 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 2 Mar 2015 13:01:12 -0800
-Subject: [PATCH] drm/vc4: Add suport for 3D rendering using the V3D engine.
-
-This is a squash of the out-of-tree development series. Since that
-series contained code from the first "get a demo triangle rendered
-using a hacked up driver using binary shader code" to "plug the last
-known security hole", it's hard to reconstruct a different series of
-incremental development that's mergeable without security holes
-throughout it.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/Makefile | 11 +-
- drivers/gpu/drm/vc4/vc4_bo.c | 476 +++++++++++++-
- drivers/gpu/drm/vc4/vc4_crtc.c | 98 ++-
- drivers/gpu/drm/vc4/vc4_debugfs.c | 3 +
- drivers/gpu/drm/vc4/vc4_drv.c | 45 +-
- drivers/gpu/drm/vc4/vc4_drv.h | 317 ++++++++++
- drivers/gpu/drm/vc4/vc4_gem.c | 686 +++++++++++++++++++++
- drivers/gpu/drm/vc4/vc4_irq.c | 211 +++++++
- drivers/gpu/drm/vc4/vc4_kms.c | 148 ++++-
- drivers/gpu/drm/vc4/vc4_packet.h | 384 ++++++++++++
- drivers/gpu/drm/vc4/vc4_plane.c | 40 ++
- drivers/gpu/drm/vc4/vc4_qpu_defines.h | 268 ++++++++
- drivers/gpu/drm/vc4/vc4_render_cl.c | 448 ++++++++++++++
- drivers/gpu/drm/vc4/vc4_trace.h | 63 ++
- drivers/gpu/drm/vc4/vc4_trace_points.c | 14 +
- drivers/gpu/drm/vc4/vc4_v3d.c | 268 ++++++++
- drivers/gpu/drm/vc4/vc4_validate.c | 958 +++++++++++++++++++++++++++++
- drivers/gpu/drm/vc4/vc4_validate_shaders.c | 521 ++++++++++++++++
- include/uapi/drm/vc4_drm.h | 229 +++++++
- 19 files changed, 5173 insertions(+), 15 deletions(-)
- create mode 100644 drivers/gpu/drm/vc4/vc4_gem.c
- create mode 100644 drivers/gpu/drm/vc4/vc4_irq.c
- create mode 100644 drivers/gpu/drm/vc4/vc4_packet.h
- create mode 100644 drivers/gpu/drm/vc4/vc4_qpu_defines.h
- create mode 100644 drivers/gpu/drm/vc4/vc4_render_cl.c
- create mode 100644 drivers/gpu/drm/vc4/vc4_trace.h
- create mode 100644 drivers/gpu/drm/vc4/vc4_trace_points.c
- create mode 100644 drivers/gpu/drm/vc4/vc4_v3d.c
- create mode 100644 drivers/gpu/drm/vc4/vc4_validate.c
- create mode 100644 drivers/gpu/drm/vc4/vc4_validate_shaders.c
- create mode 100644 include/uapi/drm/vc4_drm.h
-
---- a/drivers/gpu/drm/vc4/Makefile
-+++ b/drivers/gpu/drm/vc4/Makefile
-@@ -8,10 +8,19 @@ vc4-y := \
- vc4_crtc.o \
- vc4_drv.o \
- vc4_kms.o \
-+ vc4_gem.o \
- vc4_hdmi.o \
- vc4_hvs.o \
-- vc4_plane.o
-+ vc4_irq.o \
-+ vc4_plane.o \
-+ vc4_render_cl.o \
-+ vc4_trace_points.o \
-+ vc4_v3d.o \
-+ vc4_validate.o \
-+ vc4_validate_shaders.o
-
- vc4-$(CONFIG_DEBUG_FS) += vc4_debugfs.o
-
- obj-$(CONFIG_DRM_VC4) += vc4.o
-+
-+CFLAGS_vc4_trace_points.o := -I$(src)
---- a/drivers/gpu/drm/vc4/vc4_bo.c
-+++ b/drivers/gpu/drm/vc4/vc4_bo.c
-@@ -15,16 +15,174 @@
- */
-
- #include "vc4_drv.h"
-+#include "uapi/drm/vc4_drm.h"
-
--struct vc4_bo *vc4_bo_create(struct drm_device *dev, size_t size)
-+static void vc4_bo_stats_dump(struct vc4_dev *vc4)
- {
-+ DRM_INFO("num bos allocated: %d\n",
-+ vc4->bo_stats.num_allocated);
-+ DRM_INFO("size bos allocated: %dkb\n",
-+ vc4->bo_stats.size_allocated / 1024);
-+ DRM_INFO("num bos used: %d\n",
-+ vc4->bo_stats.num_allocated - vc4->bo_stats.num_cached);
-+ DRM_INFO("size bos used: %dkb\n",
-+ (vc4->bo_stats.size_allocated -
-+ vc4->bo_stats.size_cached) / 1024);
-+ DRM_INFO("num bos cached: %d\n",
-+ vc4->bo_stats.num_cached);
-+ DRM_INFO("size bos cached: %dkb\n",
-+ vc4->bo_stats.size_cached / 1024);
-+}
-+
-+static uint32_t bo_page_index(size_t size)
-+{
-+ return (size / PAGE_SIZE) - 1;
-+}
-+
-+/* Must be called with bo_lock held. */
-+static void vc4_bo_destroy(struct vc4_bo *bo)
-+{
-+ struct drm_gem_object *obj = &bo->base.base;
-+ struct vc4_dev *vc4 = to_vc4_dev(obj->dev);
-+
-+ if (bo->validated_shader) {
-+ kfree(bo->validated_shader->texture_samples);
-+ kfree(bo->validated_shader);
-+ bo->validated_shader = NULL;
-+ }
-+
-+ vc4->bo_stats.num_allocated--;
-+ vc4->bo_stats.size_allocated -= obj->size;
-+ drm_gem_cma_free_object(obj);
-+}
-+
-+/* Must be called with bo_lock held. */
-+static void vc4_bo_remove_from_cache(struct vc4_bo *bo)
-+{
-+ struct drm_gem_object *obj = &bo->base.base;
-+ struct vc4_dev *vc4 = to_vc4_dev(obj->dev);
-+
-+ vc4->bo_stats.num_cached--;
-+ vc4->bo_stats.size_cached -= obj->size;
-+
-+ list_del(&bo->unref_head);
-+ list_del(&bo->size_head);
-+}
-+
-+static struct list_head *vc4_get_cache_list_for_size(struct drm_device *dev,
-+ size_t size)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ uint32_t page_index = bo_page_index(size);
-+
-+ if (vc4->bo_cache.size_list_size <= page_index) {
-+ uint32_t new_size = max(vc4->bo_cache.size_list_size * 2,
-+ page_index + 1);
-+ struct list_head *new_list;
-+ uint32_t i;
-+
-+ new_list = kmalloc(new_size * sizeof(struct list_head),
-+ GFP_KERNEL);
-+ if (!new_list)
-+ return NULL;
-+
-+ /* Rebase the old cached BO lists to their new list
-+ * head locations.
-+ */
-+ for (i = 0; i < vc4->bo_cache.size_list_size; i++) {
-+ struct list_head *old_list = &vc4->bo_cache.size_list[i];
-+ if (list_empty(old_list))
-+ INIT_LIST_HEAD(&new_list[i]);
-+ else
-+ list_replace(old_list, &new_list[i]);
-+ }
-+ /* And initialize the brand new BO list heads. */
-+ for (i = vc4->bo_cache.size_list_size; i < new_size; i++)
-+ INIT_LIST_HEAD(&new_list[i]);
-+
-+ kfree(vc4->bo_cache.size_list);
-+ vc4->bo_cache.size_list = new_list;
-+ vc4->bo_cache.size_list_size = new_size;
-+ }
-+
-+ return &vc4->bo_cache.size_list[page_index];
-+}
-+
-+void vc4_bo_cache_purge(struct drm_device *dev)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+
-+ spin_lock(&vc4->bo_lock);
-+ while (!list_empty(&vc4->bo_cache.time_list)) {
-+ struct vc4_bo *bo = list_last_entry(&vc4->bo_cache.time_list,
-+ struct vc4_bo, unref_head);
-+ vc4_bo_remove_from_cache(bo);
-+ vc4_bo_destroy(bo);
-+ }
-+ spin_unlock(&vc4->bo_lock);
-+}
-+
-+struct vc4_bo *vc4_bo_create(struct drm_device *dev, size_t unaligned_size)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ uint32_t size = roundup(unaligned_size, PAGE_SIZE);
-+ uint32_t page_index = bo_page_index(size);
- struct drm_gem_cma_object *cma_obj;
-+ int pass;
-
-- cma_obj = drm_gem_cma_create(dev, size);
-- if (IS_ERR(cma_obj))
-+ if (size == 0)
- return NULL;
-- else
-- return to_vc4_bo(&cma_obj->base);
-+
-+ /* First, try to get a vc4_bo from the kernel BO cache. */
-+ spin_lock(&vc4->bo_lock);
-+ if (page_index < vc4->bo_cache.size_list_size &&
-+ !list_empty(&vc4->bo_cache.size_list[page_index])) {
-+ struct vc4_bo *bo =
-+ list_first_entry(&vc4->bo_cache.size_list[page_index],
-+ struct vc4_bo, size_head);
-+ vc4_bo_remove_from_cache(bo);
-+ spin_unlock(&vc4->bo_lock);
-+ kref_init(&bo->base.base.refcount);
-+ return bo;
-+ }
-+ spin_unlock(&vc4->bo_lock);
-+
-+ /* Otherwise, make a new BO. */
-+ for (pass = 0; ; pass++) {
-+ cma_obj = drm_gem_cma_create(dev, size);
-+ if (!IS_ERR(cma_obj))
-+ break;
-+
-+ switch (pass) {
-+ case 0:
-+ /*
-+ * If we've run out of CMA memory, kill the cache of
-+ * CMA allocations we've got laying around and try again.
-+ */
-+ vc4_bo_cache_purge(dev);
-+ break;
-+ case 1:
-+ /*
-+ * Getting desperate, so try to wait for any
-+ * previous rendering to finish, free its
-+ * unreferenced BOs to the cache, and then
-+ * free the cache.
-+ */
-+ vc4_wait_for_seqno(dev, vc4->emit_seqno, ~0ull, true);
-+ vc4_job_handle_completed(vc4);
-+ vc4_bo_cache_purge(dev);
-+ break;
-+ case 3:
-+ DRM_ERROR("Failed to allocate from CMA:\n");
-+ vc4_bo_stats_dump(vc4);
-+ return NULL;
-+ }
-+ }
-+
-+ vc4->bo_stats.num_allocated++;
-+ vc4->bo_stats.size_allocated += size;
-+
-+ return to_vc4_bo(&cma_obj->base);
- }
-
- int vc4_dumb_create(struct drm_file *file_priv,
-@@ -41,7 +199,129 @@ int vc4_dumb_create(struct drm_file *fil
- if (args->size < args->pitch * args->height)
- args->size = args->pitch * args->height;
-
-- bo = vc4_bo_create(dev, roundup(args->size, PAGE_SIZE));
-+ bo = vc4_bo_create(dev, args->size);
-+ if (!bo)
-+ return -ENOMEM;
-+
-+ ret = drm_gem_handle_create(file_priv, &bo->base.base, &args->handle);
-+ drm_gem_object_unreference_unlocked(&bo->base.base);
-+
-+ return ret;
-+}
-+
-+static void
-+vc4_bo_cache_free_old(struct drm_device *dev)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ unsigned long expire_time = jiffies - msecs_to_jiffies(1000);
-+
-+ spin_lock(&vc4->bo_lock);
-+ while (!list_empty(&vc4->bo_cache.time_list)) {
-+ struct vc4_bo *bo = list_last_entry(&vc4->bo_cache.time_list,
-+ struct vc4_bo, unref_head);
-+ if (time_before(expire_time, bo->free_time)) {
-+ mod_timer(&vc4->bo_cache.time_timer,
-+ round_jiffies_up(jiffies +
-+ msecs_to_jiffies(1000)));
-+ spin_unlock(&vc4->bo_lock);
-+ return;
-+ }
-+
-+ vc4_bo_remove_from_cache(bo);
-+ vc4_bo_destroy(bo);
-+ }
-+ spin_unlock(&vc4->bo_lock);
-+}
-+
-+/* Called on the last userspace/kernel unreference of the BO. Returns
-+ * it to the BO cache if possible, otherwise frees it.
-+ *
-+ * Note that this is called with the struct_mutex held.
-+ */
-+void vc4_free_object(struct drm_gem_object *gem_bo)
-+{
-+ struct drm_device *dev = gem_bo->dev;
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ struct vc4_bo *bo = to_vc4_bo(gem_bo);
-+ struct list_head *cache_list;
-+
-+ /* If the object references someone else's memory, we can't cache it.
-+ */
-+ if (gem_bo->import_attach) {
-+ vc4_bo_destroy(bo);
-+ return;
-+ }
-+
-+ /* Don't cache if it was publicly named. */
-+ if (gem_bo->name) {
-+ vc4_bo_destroy(bo);
-+ return;
-+ }
-+
-+ spin_lock(&vc4->bo_lock);
-+ cache_list = vc4_get_cache_list_for_size(dev, gem_bo->size);
-+ if (!cache_list) {
-+ vc4_bo_destroy(bo);
-+ spin_unlock(&vc4->bo_lock);
-+ return;
-+ }
-+
-+ if (bo->validated_shader) {
-+ kfree(bo->validated_shader->texture_samples);
-+ kfree(bo->validated_shader);
-+ bo->validated_shader = NULL;
-+ }
-+
-+ bo->free_time = jiffies;
-+ list_add(&bo->size_head, cache_list);
-+ list_add(&bo->unref_head, &vc4->bo_cache.time_list);
-+
-+ vc4->bo_stats.num_cached++;
-+ vc4->bo_stats.size_cached += gem_bo->size;
-+ spin_unlock(&vc4->bo_lock);
-+
-+ vc4_bo_cache_free_old(dev);
-+}
-+
-+static void vc4_bo_cache_time_work(struct work_struct *work)
-+{
-+ struct vc4_dev *vc4 =
-+ container_of(work, struct vc4_dev, bo_cache.time_work);
-+ struct drm_device *dev = vc4->dev;
-+
-+ vc4_bo_cache_free_old(dev);
-+}
-+
-+static void vc4_bo_cache_time_timer(unsigned long data)
-+{
-+ struct drm_device *dev = (struct drm_device *)data;
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+
-+ schedule_work(&vc4->bo_cache.time_work);
-+}
-+
-+struct dma_buf *
-+vc4_prime_export(struct drm_device *dev, struct drm_gem_object *obj, int flags)
-+{
-+ struct vc4_bo *bo = to_vc4_bo(obj);
-+
-+ if (bo->validated_shader) {
-+ DRM_ERROR("Attempting to export shader BO\n");
-+ return ERR_PTR(-EINVAL);
-+ }
-+
-+ return drm_gem_prime_export(dev, obj, flags);
-+}
-+
-+int
-+vc4_create_bo_ioctl(struct drm_device *dev, void *data,
-+ struct drm_file *file_priv)
-+{
-+ struct drm_vc4_create_bo *args = data;
-+ struct vc4_bo *bo = NULL;
-+ int ret;
-+
-+ bo = vc4_bo_create(dev, args->size);
- if (!bo)
- return -ENOMEM;
-
-@@ -50,3 +330,187 @@ int vc4_dumb_create(struct drm_file *fil
-
- return ret;
- }
-+
-+int
-+vc4_create_shader_bo_ioctl(struct drm_device *dev, void *data,
-+ struct drm_file *file_priv)
-+{
-+ struct drm_vc4_create_shader_bo *args = data;
-+ struct vc4_bo *bo = NULL;
-+ int ret;
-+
-+ if (args->size == 0)
-+ return -EINVAL;
-+
-+ if (args->size % sizeof(u64) != 0)
-+ return -EINVAL;
-+
-+ if (args->flags != 0) {
-+ DRM_INFO("Unknown flags set: 0x%08x\n", args->flags);
-+ return -EINVAL;
-+ }
-+
-+ if (args->pad != 0) {
-+ DRM_INFO("Pad set: 0x%08x\n", args->pad);
-+ return -EINVAL;
-+ }
-+
-+ bo = vc4_bo_create(dev, args->size);
-+ if (!bo)
-+ return -ENOMEM;
-+
-+ ret = copy_from_user(bo->base.vaddr,
-+ (void __user *)(uintptr_t)args->data,
-+ args->size);
-+ if (ret != 0)
-+ goto fail;
-+
-+ bo->validated_shader = vc4_validate_shader(&bo->base);
-+ if (!bo->validated_shader) {
-+ ret = -EINVAL;
-+ goto fail;
-+ }
-+
-+ /* We have to create the handle after validation, to avoid
-+ * races for users to do doing things like mmap the shader BO.
-+ */
-+ ret = drm_gem_handle_create(file_priv, &bo->base.base, &args->handle);
-+
-+ fail:
-+ drm_gem_object_unreference_unlocked(&bo->base.base);
-+
-+ return ret;
-+}
-+
-+int
-+vc4_mmap_bo_ioctl(struct drm_device *dev, void *data,
-+ struct drm_file *file_priv)
-+{
-+ struct drm_vc4_mmap_bo *args = data;
-+ struct drm_gem_object *gem_obj;
-+
-+ gem_obj = drm_gem_object_lookup(dev, file_priv, args->handle);
-+ if (!gem_obj) {
-+ DRM_ERROR("Failed to look up GEM BO %d\n", args->handle);
-+ return -EINVAL;
-+ }
-+
-+ /* The mmap offset was set up at BO allocation time. */
-+ args->offset = drm_vma_node_offset_addr(&gem_obj->vma_node);
-+
-+ drm_gem_object_unreference(gem_obj);
-+ return 0;
-+}
-+
-+int vc4_mmap(struct file *filp, struct vm_area_struct *vma)
-+{
-+ struct drm_gem_object *gem_obj;
-+ struct vc4_bo *bo;
-+ int ret;
-+
-+ ret = drm_gem_mmap(filp, vma);
-+ if (ret)
-+ return ret;
-+
-+ gem_obj = vma->vm_private_data;
-+ bo = to_vc4_bo(gem_obj);
-+
-+ if (bo->validated_shader) {
-+ DRM_ERROR("mmaping of shader BOs not allowed.\n");
-+ return -EINVAL;
-+ }
-+
-+ /*
-+ * Clear the VM_PFNMAP flag that was set by drm_gem_mmap(), and set the
-+ * vm_pgoff (used as a fake buffer offset by DRM) to 0 as we want to map
-+ * the whole buffer.
-+ */
-+ vma->vm_flags &= ~VM_PFNMAP;
-+ vma->vm_pgoff = 0;
-+
-+ ret = dma_mmap_writecombine(bo->base.base.dev->dev, vma,
-+ bo->base.vaddr, bo->base.paddr,
-+ vma->vm_end - vma->vm_start);
-+ if (ret)
-+ drm_gem_vm_close(vma);
-+
-+ return ret;
-+}
-+
-+int vc4_prime_mmap(struct drm_gem_object *obj, struct vm_area_struct *vma)
-+{
-+ struct vc4_bo *bo = to_vc4_bo(obj);
-+
-+ if (bo->validated_shader) {
-+ DRM_ERROR("mmaping of shader BOs not allowed.\n");
-+ return -EINVAL;
-+ }
-+
-+ return drm_gem_cma_prime_mmap(obj, vma);
-+}
-+
-+void *vc4_prime_vmap(struct drm_gem_object *obj)
-+{
-+ struct vc4_bo *bo = to_vc4_bo(obj);
-+
-+ if (bo->validated_shader) {
-+ DRM_ERROR("mmaping of shader BOs not allowed.\n");
-+ return ERR_PTR(-EINVAL);
-+ }
-+
-+ return drm_gem_cma_prime_vmap(obj);
-+}
-+
-+void vc4_bo_cache_init(struct drm_device *dev)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+
-+ spin_lock_init(&vc4->bo_lock);
-+
-+ INIT_LIST_HEAD(&vc4->bo_cache.time_list);
-+
-+ INIT_WORK(&vc4->bo_cache.time_work, vc4_bo_cache_time_work);
-+ setup_timer(&vc4->bo_cache.time_timer,
-+ vc4_bo_cache_time_timer,
-+ (unsigned long) dev);
-+}
-+
-+void vc4_bo_cache_destroy(struct drm_device *dev)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+
-+ del_timer(&vc4->bo_cache.time_timer);
-+ cancel_work_sync(&vc4->bo_cache.time_work);
-+
-+ vc4_bo_cache_purge(dev);
-+
-+ if (vc4->bo_stats.num_allocated) {
-+ DRM_ERROR("Destroying BO cache while BOs still allocated:\n");
-+ vc4_bo_stats_dump(vc4);
-+ }
-+}
-+
-+#ifdef CONFIG_DEBUG_FS
-+int vc4_bo_stats_debugfs(struct seq_file *m, void *unused)
-+{
-+ struct drm_info_node *node = (struct drm_info_node *) m->private;
-+ struct drm_device *dev = node->minor->dev;
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ struct vc4_bo_stats stats;
-+
-+ spin_lock(&vc4->bo_lock);
-+ stats = vc4->bo_stats;
-+ spin_unlock(&vc4->bo_lock);
-+
-+ seq_printf(m, "num bos allocated: %d\n", stats.num_allocated);
-+ seq_printf(m, "size bos allocated: %dkb\n", stats.size_allocated / 1024);
-+ seq_printf(m, "num bos used: %d\n", (stats.num_allocated -
-+ stats.num_cached));
-+ seq_printf(m, "size bos used: %dkb\n", (stats.size_allocated -
-+ stats.size_cached) / 1024);
-+ seq_printf(m, "num bos cached: %d\n", stats.num_cached);
-+ seq_printf(m, "size bos cached: %dkb\n", stats.size_cached / 1024);
-+
-+ return 0;
-+}
-+#endif
---- a/drivers/gpu/drm/vc4/vc4_crtc.c
-+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
-@@ -35,6 +35,7 @@
- #include "drm_atomic_helper.h"
- #include "drm_crtc_helper.h"
- #include "linux/clk.h"
-+#include "drm_fb_cma_helper.h"
- #include "linux/component.h"
- #include "linux/of_device.h"
- #include "vc4_drv.h"
-@@ -476,10 +477,105 @@ static irqreturn_t vc4_crtc_irq_handler(
- return ret;
- }
-
-+struct vc4_async_flip_state {
-+ struct drm_crtc *crtc;
-+ struct drm_framebuffer *fb;
-+ struct drm_pending_vblank_event *event;
-+
-+ struct vc4_seqno_cb cb;
-+};
-+
-+/* Called when the V3D execution for the BO being flipped to is done, so that
-+ * we can actually update the plane's address to point to it.
-+ */
-+static void
-+vc4_async_page_flip_complete(struct vc4_seqno_cb *cb)
-+{
-+ struct vc4_async_flip_state *flip_state =
-+ container_of(cb, struct vc4_async_flip_state, cb);
-+ struct drm_crtc *crtc = flip_state->crtc;
-+ struct drm_device *dev = crtc->dev;
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ struct drm_plane *plane = crtc->primary;
-+
-+ vc4_plane_async_set_fb(plane, flip_state->fb);
-+ if (flip_state->event) {
-+ unsigned long flags;
-+ spin_lock_irqsave(&dev->event_lock, flags);
-+ drm_crtc_send_vblank_event(crtc, flip_state->event);
-+ spin_unlock_irqrestore(&dev->event_lock, flags);
-+ }
-+
-+ drm_framebuffer_unreference(flip_state->fb);
-+ kfree(flip_state);
-+
-+ up(&vc4->async_modeset);
-+}
-+
-+/* Implements async (non-vblank-synced) page flips.
-+ *
-+ * The page flip ioctl needs to return immediately, so we grab the
-+ * modeset semaphore on the pipe, and queue the address update for
-+ * when V3D is done with the BO being flipped to.
-+ */
-+static int vc4_async_page_flip(struct drm_crtc *crtc,
-+ struct drm_framebuffer *fb,
-+ struct drm_pending_vblank_event *event,
-+ uint32_t flags)
-+{
-+ struct drm_device *dev = crtc->dev;
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ struct drm_plane *plane = crtc->primary;
-+ int ret = 0;
-+ struct vc4_async_flip_state *flip_state;
-+ struct drm_gem_cma_object *cma_bo = drm_fb_cma_get_gem_obj(fb, 0);
-+ struct vc4_bo *bo = to_vc4_bo(&cma_bo->base);
-+
-+ flip_state = kzalloc(sizeof(*flip_state), GFP_KERNEL);
-+ if (!flip_state)
-+ return -ENOMEM;
-+
-+ drm_framebuffer_reference(fb);
-+ flip_state->fb = fb;
-+ flip_state->crtc = crtc;
-+ flip_state->event = event;
-+
-+ /* Make sure all other async modesetes have landed. */
-+ ret = down_interruptible(&vc4->async_modeset);
-+ if (ret) {
-+ kfree(flip_state);
-+ return ret;
-+ }
-+
-+ /* Immediately update the plane's legacy fb pointer, so that later
-+ * modeset prep sees the state that will be present when the semaphore
-+ * is released.
-+ */
-+ drm_atomic_set_fb_for_plane(plane->state, fb);
-+ plane->fb = fb;
-+
-+ vc4_queue_seqno_cb(dev, &flip_state->cb, bo->seqno,
-+ vc4_async_page_flip_complete);
-+
-+ /* Driver takes ownership of state on successful async commit. */
-+ return 0;
-+}
-+
-+static int vc4_page_flip(struct drm_crtc *crtc,
-+ struct drm_framebuffer *fb,
-+ struct drm_pending_vblank_event *event,
-+ uint32_t flags)
-+{
-+ if (flags & DRM_MODE_PAGE_FLIP_ASYNC)
-+ return vc4_async_page_flip(crtc, fb, event, flags);
-+ else
-+ return drm_atomic_helper_page_flip(crtc, fb, event, flags);
-+}
-+
- static const struct drm_crtc_funcs vc4_crtc_funcs = {
- .set_config = drm_atomic_helper_set_config,
- .destroy = vc4_crtc_destroy,
-- .page_flip = drm_atomic_helper_page_flip,
-+ .page_flip = vc4_page_flip,
- .set_property = NULL,
- .cursor_set = NULL, /* handled by drm_mode_cursor_universal */
- .cursor_move = NULL, /* handled by drm_mode_cursor_universal */
---- a/drivers/gpu/drm/vc4/vc4_debugfs.c
-+++ b/drivers/gpu/drm/vc4/vc4_debugfs.c
-@@ -16,11 +16,14 @@
- #include "vc4_regs.h"
-
- static const struct drm_info_list vc4_debugfs_list[] = {
-+ {"bo_stats", vc4_bo_stats_debugfs, 0},
- {"hdmi_regs", vc4_hdmi_debugfs_regs, 0},
- {"hvs_regs", vc4_hvs_debugfs_regs, 0},
- {"crtc0_regs", vc4_crtc_debugfs_regs, 0, (void *)(uintptr_t)0},
- {"crtc1_regs", vc4_crtc_debugfs_regs, 0, (void *)(uintptr_t)1},
- {"crtc2_regs", vc4_crtc_debugfs_regs, 0, (void *)(uintptr_t)2},
-+ {"v3d_ident", vc4_v3d_debugfs_ident, 0},
-+ {"v3d_regs", vc4_v3d_debugfs_regs, 0},
- };
-
- #define VC4_DEBUGFS_ENTRIES ARRAY_SIZE(vc4_debugfs_list)
---- a/drivers/gpu/drm/vc4/vc4_drv.c
-+++ b/drivers/gpu/drm/vc4/vc4_drv.c
-@@ -14,8 +14,10 @@
- #include <linux/module.h>
- #include <linux/of_platform.h>
- #include <linux/platform_device.h>
-+#include <soc/bcm2835/raspberrypi-firmware.h>
- #include "drm_fb_cma_helper.h"
-
-+#include "uapi/drm/vc4_drm.h"
- #include "vc4_drv.h"
- #include "vc4_regs.h"
-
-@@ -63,7 +65,7 @@ static const struct file_operations vc4_
- .open = drm_open,
- .release = drm_release,
- .unlocked_ioctl = drm_ioctl,
-- .mmap = drm_gem_cma_mmap,
-+ .mmap = vc4_mmap,
- .poll = drm_poll,
- .read = drm_read,
- #ifdef CONFIG_COMPAT
-@@ -73,16 +75,28 @@ static const struct file_operations vc4_
- };
-
- static const struct drm_ioctl_desc vc4_drm_ioctls[] = {
-+ DRM_IOCTL_DEF_DRV(VC4_SUBMIT_CL, vc4_submit_cl_ioctl, 0),
-+ DRM_IOCTL_DEF_DRV(VC4_WAIT_SEQNO, vc4_wait_seqno_ioctl, 0),
-+ DRM_IOCTL_DEF_DRV(VC4_WAIT_BO, vc4_wait_bo_ioctl, 0),
-+ DRM_IOCTL_DEF_DRV(VC4_CREATE_BO, vc4_create_bo_ioctl, 0),
-+ DRM_IOCTL_DEF_DRV(VC4_MMAP_BO, vc4_mmap_bo_ioctl, 0),
-+ DRM_IOCTL_DEF_DRV(VC4_CREATE_SHADER_BO, vc4_create_shader_bo_ioctl, 0),
- };
-
- static struct drm_driver vc4_drm_driver = {
- .driver_features = (DRIVER_MODESET |
- DRIVER_ATOMIC |
- DRIVER_GEM |
-+ DRIVER_HAVE_IRQ |
- DRIVER_PRIME),
- .lastclose = vc4_lastclose,
- .preclose = vc4_drm_preclose,
-
-+ .irq_handler = vc4_irq,
-+ .irq_preinstall = vc4_irq_preinstall,
-+ .irq_postinstall = vc4_irq_postinstall,
-+ .irq_uninstall = vc4_irq_uninstall,
-+
- .enable_vblank = vc4_enable_vblank,
- .disable_vblank = vc4_disable_vblank,
- .get_vblank_counter = drm_vblank_count,
-@@ -92,18 +106,18 @@ static struct drm_driver vc4_drm_driver
- .debugfs_cleanup = vc4_debugfs_cleanup,
- #endif
-
-- .gem_free_object = drm_gem_cma_free_object,
-+ .gem_free_object = vc4_free_object,
- .gem_vm_ops = &drm_gem_cma_vm_ops,
-
- .prime_handle_to_fd = drm_gem_prime_handle_to_fd,
- .prime_fd_to_handle = drm_gem_prime_fd_to_handle,
- .gem_prime_import = drm_gem_prime_import,
-- .gem_prime_export = drm_gem_prime_export,
-+ .gem_prime_export = vc4_prime_export,
- .gem_prime_get_sg_table = drm_gem_cma_prime_get_sg_table,
- .gem_prime_import_sg_table = drm_gem_cma_prime_import_sg_table,
-- .gem_prime_vmap = drm_gem_cma_prime_vmap,
-+ .gem_prime_vmap = vc4_prime_vmap,
- .gem_prime_vunmap = drm_gem_cma_prime_vunmap,
-- .gem_prime_mmap = drm_gem_cma_prime_mmap,
-+ .gem_prime_mmap = vc4_prime_mmap,
-
- .dumb_create = vc4_dumb_create,
- .dumb_map_offset = drm_gem_cma_dumb_map_offset,
-@@ -113,6 +127,8 @@ static struct drm_driver vc4_drm_driver
- .num_ioctls = ARRAY_SIZE(vc4_drm_ioctls),
- .fops = &vc4_drm_fops,
-
-+ .gem_obj_size = sizeof(struct vc4_bo),
-+
- .name = DRIVER_NAME,
- .desc = DRIVER_DESC,
- .date = DRIVER_DATE,
-@@ -153,6 +169,7 @@ static int vc4_drm_bind(struct device *d
- struct drm_device *drm;
- struct drm_connector *connector;
- struct vc4_dev *vc4;
-+ struct device_node *firmware_node;
- int ret = 0;
-
- dev->coherent_dma_mask = DMA_BIT_MASK(32);
-@@ -161,6 +178,14 @@ static int vc4_drm_bind(struct device *d
- if (!vc4)
- return -ENOMEM;
-
-+ firmware_node = of_parse_phandle(dev->of_node, "firmware", 0);
-+ vc4->firmware = rpi_firmware_get(firmware_node);
-+ if (!vc4->firmware) {
-+ DRM_DEBUG("Failed to get Raspberry Pi firmware reference.\n");
-+ return -EPROBE_DEFER;
-+ }
-+ of_node_put(firmware_node);
-+
- drm = drm_dev_alloc(&vc4_drm_driver, dev);
- if (!drm)
- return -ENOMEM;
-@@ -170,13 +195,17 @@ static int vc4_drm_bind(struct device *d
-
- drm_dev_set_unique(drm, dev_name(dev));
-
-+ vc4_bo_cache_init(drm);
-+
- drm_mode_config_init(drm);
- if (ret)
- goto unref;
-
-+ vc4_gem_init(drm);
-+
- ret = component_bind_all(dev, drm);
- if (ret)
-- goto unref;
-+ goto gem_destroy;
-
- ret = drm_dev_register(drm, 0);
- if (ret < 0)
-@@ -200,8 +229,11 @@ unregister:
- drm_dev_unregister(drm);
- unbind_all:
- component_unbind_all(dev, drm);
-+gem_destroy:
-+ vc4_gem_destroy(drm);
- unref:
- drm_dev_unref(drm);
-+ vc4_bo_cache_destroy(drm);
- return ret;
- }
-
-@@ -228,6 +260,7 @@ static struct platform_driver *const com
- &vc4_hdmi_driver,
- &vc4_crtc_driver,
- &vc4_hvs_driver,
-+ &vc4_v3d_driver,
- };
-
- static int vc4_platform_drm_probe(struct platform_device *pdev)
---- a/drivers/gpu/drm/vc4/vc4_drv.h
-+++ b/drivers/gpu/drm/vc4/vc4_drv.h
-@@ -15,8 +15,85 @@ struct vc4_dev {
- struct vc4_hdmi *hdmi;
- struct vc4_hvs *hvs;
- struct vc4_crtc *crtc[3];
-+ struct vc4_v3d *v3d;
-
- struct drm_fbdev_cma *fbdev;
-+ struct rpi_firmware *firmware;
-+
-+ /* The kernel-space BO cache. Tracks buffers that have been
-+ * unreferenced by all other users (refcounts of 0!) but not
-+ * yet freed, so we can do cheap allocations.
-+ */
-+ struct vc4_bo_cache {
-+ /* Array of list heads for entries in the BO cache,
-+ * based on number of pages, so we can do O(1) lookups
-+ * in the cache when allocating.
-+ */
-+ struct list_head *size_list;
-+ uint32_t size_list_size;
-+
-+ /* List of all BOs in the cache, ordered by age, so we
-+ * can do O(1) lookups when trying to free old
-+ * buffers.
-+ */
-+ struct list_head time_list;
-+ struct work_struct time_work;
-+ struct timer_list time_timer;
-+ } bo_cache;
-+
-+ struct vc4_bo_stats {
-+ u32 num_allocated;
-+ u32 size_allocated;
-+ u32 num_cached;
-+ u32 size_cached;
-+ } bo_stats;
-+
-+ /* Protects bo_cache and the BO stats. */
-+ spinlock_t bo_lock;
-+
-+ /* Sequence number for the last job queued in job_list.
-+ * Starts at 0 (no jobs emitted).
-+ */
-+ uint64_t emit_seqno;
-+
-+ /* Sequence number for the last completed job on the GPU.
-+ * Starts at 0 (no jobs completed).
-+ */
-+ uint64_t finished_seqno;
-+
-+ /* List of all struct vc4_exec_info for jobs to be executed.
-+ * The first job in the list is the one currently programmed
-+ * into ct0ca/ct1ca for execution.
-+ */
-+ struct list_head job_list;
-+ /* List of the finished vc4_exec_infos waiting to be freed by
-+ * job_done_work.
-+ */
-+ struct list_head job_done_list;
-+ spinlock_t job_lock;
-+ wait_queue_head_t job_wait_queue;
-+ struct work_struct job_done_work;
-+
-+ /* List of struct vc4_seqno_cb for callbacks to be made from a
-+ * workqueue when the given seqno is passed.
-+ */
-+ struct list_head seqno_cb_list;
-+
-+ /* The binner overflow memory that's currently set up in
-+ * BPOA/BPOS registers. When overflow occurs and a new one is
-+ * allocated, the previous one will be moved to
-+ * vc4->current_exec's free list.
-+ */
-+ struct vc4_bo *overflow_mem;
-+ struct work_struct overflow_mem_work;
-+
-+ struct {
-+ uint32_t last_ct0ca, last_ct1ca;
-+ struct timer_list timer;
-+ struct work_struct reset_work;
-+ } hangcheck;
-+
-+ struct semaphore async_modeset;
- };
-
- static inline struct vc4_dev *
-@@ -27,6 +104,25 @@ to_vc4_dev(struct drm_device *dev)
-
- struct vc4_bo {
- struct drm_gem_cma_object base;
-+
-+ /* seqno of the last job to render to this BO. */
-+ uint64_t seqno;
-+
-+ /* List entry for the BO's position in either
-+ * vc4_exec_info->unref_list or vc4_dev->bo_cache.time_list
-+ */
-+ struct list_head unref_head;
-+
-+ /* Time in jiffies when the BO was put in vc4->bo_cache. */
-+ unsigned long free_time;
-+
-+ /* List entry for the BO's position in vc4_dev->bo_cache.size_list */
-+ struct list_head size_head;
-+
-+ /* Struct for shader validation state, if created by
-+ * DRM_IOCTL_VC4_CREATE_SHADER_BO.
-+ */
-+ struct vc4_validated_shader_info *validated_shader;
- };
-
- static inline struct vc4_bo *
-@@ -35,6 +131,17 @@ to_vc4_bo(struct drm_gem_object *bo)
- return (struct vc4_bo *)bo;
- }
-
-+struct vc4_seqno_cb {
-+ struct work_struct work;
-+ uint64_t seqno;
-+ void (*func)(struct vc4_seqno_cb *cb);
-+};
-+
-+struct vc4_v3d {
-+ struct platform_device *pdev;
-+ void __iomem *regs;
-+};
-+
- struct vc4_hvs {
- struct platform_device *pdev;
- void __iomem *regs;
-@@ -72,9 +179,151 @@ to_vc4_encoder(struct drm_encoder *encod
- return container_of(encoder, struct vc4_encoder, base);
- }
-
-+#define V3D_READ(offset) readl(vc4->v3d->regs + offset)
-+#define V3D_WRITE(offset, val) writel(val, vc4->v3d->regs + offset)
- #define HVS_READ(offset) readl(vc4->hvs->regs + offset)
- #define HVS_WRITE(offset, val) writel(val, vc4->hvs->regs + offset)
-
-+enum vc4_bo_mode {
-+ VC4_MODE_UNDECIDED,
-+ VC4_MODE_RENDER,
-+ VC4_MODE_SHADER,
-+};
-+
-+struct vc4_bo_exec_state {
-+ struct drm_gem_cma_object *bo;
-+ enum vc4_bo_mode mode;
-+};
-+
-+struct vc4_exec_info {
-+ /* Sequence number for this bin/render job. */
-+ uint64_t seqno;
-+
-+ /* Kernel-space copy of the ioctl arguments */
-+ struct drm_vc4_submit_cl *args;
-+
-+ /* This is the array of BOs that were looked up at the start of exec.
-+ * Command validation will use indices into this array.
-+ */
-+ struct vc4_bo_exec_state *bo;
-+ uint32_t bo_count;
-+
-+ /* Pointers for our position in vc4->job_list */
-+ struct list_head head;
-+
-+ /* List of other BOs used in the job that need to be released
-+ * once the job is complete.
-+ */
-+ struct list_head unref_list;
-+
-+ /* Current unvalidated indices into @bo loaded by the non-hardware
-+ * VC4_PACKET_GEM_HANDLES.
-+ */
-+ uint32_t bo_index[2];
-+
-+ /* This is the BO where we store the validated command lists, shader
-+ * records, and uniforms.
-+ */
-+ struct drm_gem_cma_object *exec_bo;
-+
-+ /**
-+ * This tracks the per-shader-record state (packet 64) that
-+ * determines the length of the shader record and the offset
-+ * it's expected to be found at. It gets read in from the
-+ * command lists.
-+ */
-+ struct vc4_shader_state {
-+ uint8_t packet;
-+ uint32_t addr;
-+ /* Maximum vertex index referenced by any primitive using this
-+ * shader state.
-+ */
-+ uint32_t max_index;
-+ } *shader_state;
-+
-+ /** How many shader states the user declared they were using. */
-+ uint32_t shader_state_size;
-+ /** How many shader state records the validator has seen. */
-+ uint32_t shader_state_count;
-+
-+ bool found_tile_binning_mode_config_packet;
-+ bool found_start_tile_binning_packet;
-+ bool found_increment_semaphore_packet;
-+ uint8_t bin_tiles_x, bin_tiles_y;
-+ struct drm_gem_cma_object *tile_bo;
-+ uint32_t tile_alloc_offset;
-+
-+ /**
-+ * Computed addresses pointing into exec_bo where we start the
-+ * bin thread (ct0) and render thread (ct1).
-+ */
-+ uint32_t ct0ca, ct0ea;
-+ uint32_t ct1ca, ct1ea;
-+
-+ /* Pointers to the shader recs. These paddr gets incremented as CL
-+ * packets are relocated in validate_gl_shader_state, and the vaddrs
-+ * (u and v) get incremented and size decremented as the shader recs
-+ * themselves are validated.
-+ */
-+ void *shader_rec_u;
-+ void *shader_rec_v;
-+ uint32_t shader_rec_p;
-+ uint32_t shader_rec_size;
-+
-+ /* Pointers to the uniform data. These pointers are incremented, and
-+ * size decremented, as each batch of uniforms is uploaded.
-+ */
-+ void *uniforms_u;
-+ void *uniforms_v;
-+ uint32_t uniforms_p;
-+ uint32_t uniforms_size;
-+};
-+
-+static inline struct vc4_exec_info *
-+vc4_first_job(struct vc4_dev *vc4)
-+{
-+ if (list_empty(&vc4->job_list))
-+ return NULL;
-+ return list_first_entry(&vc4->job_list, struct vc4_exec_info, head);
-+}
-+
-+/**
-+ * struct vc4_texture_sample_info - saves the offsets into the UBO for texture
-+ * setup parameters.
-+ *
-+ * This will be used at draw time to relocate the reference to the texture
-+ * contents in p0, and validate that the offset combined with
-+ * width/height/stride/etc. from p1 and p2/p3 doesn't sample outside the BO.
-+ * Note that the hardware treats unprovided config parameters as 0, so not all
-+ * of them need to be set up for every texure sample, and we'll store ~0 as
-+ * the offset to mark the unused ones.
-+ *
-+ * See the VC4 3D architecture guide page 41 ("Texture and Memory Lookup Unit
-+ * Setup") for definitions of the texture parameters.
-+ */
-+struct vc4_texture_sample_info {
-+ bool is_direct;
-+ uint32_t p_offset[4];
-+};
-+
-+/**
-+ * struct vc4_validated_shader_info - information about validated shaders that
-+ * needs to be used from command list validation.
-+ *
-+ * For a given shader, each time a shader state record references it, we need
-+ * to verify that the shader doesn't read more uniforms than the shader state
-+ * record's uniform BO pointer can provide, and we need to apply relocations
-+ * and validate the shader state record's uniforms that define the texture
-+ * samples.
-+ */
-+struct vc4_validated_shader_info
-+{
-+ uint32_t uniforms_size;
-+ uint32_t uniforms_src_size;
-+ uint32_t num_texture_samples;
-+ struct vc4_texture_sample_info *texture_samples;
-+};
-+
- /**
- * _wait_for - magic (register) wait macro
- *
-@@ -111,6 +360,18 @@ int vc4_dumb_create(struct drm_file *fil
- struct drm_mode_create_dumb *args);
- struct dma_buf *vc4_prime_export(struct drm_device *dev,
- struct drm_gem_object *obj, int flags);
-+int vc4_create_bo_ioctl(struct drm_device *dev, void *data,
-+ struct drm_file *file_priv);
-+int vc4_create_shader_bo_ioctl(struct drm_device *dev, void *data,
-+ struct drm_file *file_priv);
-+int vc4_mmap_bo_ioctl(struct drm_device *dev, void *data,
-+ struct drm_file *file_priv);
-+int vc4_mmap(struct file *filp, struct vm_area_struct *vma);
-+int vc4_prime_mmap(struct drm_gem_object *obj, struct vm_area_struct *vma);
-+void *vc4_prime_vmap(struct drm_gem_object *obj);
-+void vc4_bo_cache_init(struct drm_device *dev);
-+void vc4_bo_cache_destroy(struct drm_device *dev);
-+int vc4_bo_stats_debugfs(struct seq_file *m, void *arg);
-
- /* vc4_crtc.c */
- extern struct platform_driver vc4_crtc_driver;
-@@ -126,10 +387,34 @@ void vc4_debugfs_cleanup(struct drm_mino
- /* vc4_drv.c */
- void __iomem *vc4_ioremap_regs(struct platform_device *dev, int index);
-
-+/* vc4_gem.c */
-+void vc4_gem_init(struct drm_device *dev);
-+void vc4_gem_destroy(struct drm_device *dev);
-+int vc4_submit_cl_ioctl(struct drm_device *dev, void *data,
-+ struct drm_file *file_priv);
-+int vc4_wait_seqno_ioctl(struct drm_device *dev, void *data,
-+ struct drm_file *file_priv);
-+int vc4_wait_bo_ioctl(struct drm_device *dev, void *data,
-+ struct drm_file *file_priv);
-+void vc4_submit_next_job(struct drm_device *dev);
-+int vc4_wait_for_seqno(struct drm_device *dev, uint64_t seqno,
-+ uint64_t timeout_ns, bool interruptible);
-+void vc4_job_handle_completed(struct vc4_dev *vc4);
-+int vc4_queue_seqno_cb(struct drm_device *dev,
-+ struct vc4_seqno_cb *cb, uint64_t seqno,
-+ void (*func)(struct vc4_seqno_cb *cb));
-+
- /* vc4_hdmi.c */
- extern struct platform_driver vc4_hdmi_driver;
- int vc4_hdmi_debugfs_regs(struct seq_file *m, void *unused);
-
-+/* vc4_irq.c */
-+irqreturn_t vc4_irq(int irq, void *arg);
-+void vc4_irq_preinstall(struct drm_device *dev);
-+int vc4_irq_postinstall(struct drm_device *dev);
-+void vc4_irq_uninstall(struct drm_device *dev);
-+void vc4_irq_reset(struct drm_device *dev);
-+
- /* vc4_hvs.c */
- extern struct platform_driver vc4_hvs_driver;
- void vc4_hvs_dump_state(struct drm_device *dev);
-@@ -143,3 +428,35 @@ struct drm_plane *vc4_plane_init(struct
- enum drm_plane_type type);
- u32 vc4_plane_write_dlist(struct drm_plane *plane, u32 __iomem *dlist);
- u32 vc4_plane_dlist_size(struct drm_plane_state *state);
-+void vc4_plane_async_set_fb(struct drm_plane *plane, struct drm_framebuffer *fb);
-+
-+/* vc4_v3d.c */
-+extern struct platform_driver vc4_v3d_driver;
-+int vc4_v3d_debugfs_ident(struct seq_file *m, void *unused);
-+int vc4_v3d_debugfs_regs(struct seq_file *m, void *unused);
-+int vc4_v3d_set_power(struct vc4_dev *vc4, bool on);
-+
-+/* vc4_validate.c */
-+int
-+vc4_validate_bin_cl(struct drm_device *dev,
-+ void *validated,
-+ void *unvalidated,
-+ struct vc4_exec_info *exec);
-+
-+int
-+vc4_validate_shader_recs(struct drm_device *dev, struct vc4_exec_info *exec);
-+
-+struct vc4_validated_shader_info *
-+vc4_validate_shader(struct drm_gem_cma_object *shader_obj);
-+
-+bool vc4_use_bo(struct vc4_exec_info *exec,
-+ uint32_t hindex,
-+ enum vc4_bo_mode mode,
-+ struct drm_gem_cma_object **obj);
-+
-+int vc4_get_rcl(struct drm_device *dev, struct vc4_exec_info *exec);
-+
-+bool vc4_check_tex_size(struct vc4_exec_info *exec,
-+ struct drm_gem_cma_object *fbo,
-+ uint32_t offset, uint8_t tiling_format,
-+ uint32_t width, uint32_t height, uint8_t cpp);
---- /dev/null
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -0,0 +1,686 @@
-+/*
-+ * Copyright © 2014 Broadcom
-+ *
-+ * Permission is hereby granted, free of charge, to any person obtaining a
-+ * copy of this software and associated documentation files (the "Software"),
-+ * to deal in the Software without restriction, including without limitation
-+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
-+ * and/or sell copies of the Software, and to permit persons to whom the
-+ * Software is furnished to do so, subject to the following conditions:
-+ *
-+ * The above copyright notice and this permission notice (including the next
-+ * paragraph) shall be included in all copies or substantial portions of the
-+ * Software.
-+ *
-+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
-+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
-+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
-+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
-+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
-+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS
-+ * IN THE SOFTWARE.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+#include <linux/device.h>
-+#include <linux/io.h>
-+
-+#include "uapi/drm/vc4_drm.h"
-+#include "vc4_drv.h"
-+#include "vc4_regs.h"
-+#include "vc4_trace.h"
-+
-+static void
-+vc4_queue_hangcheck(struct drm_device *dev)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+
-+ mod_timer(&vc4->hangcheck.timer,
-+ round_jiffies_up(jiffies + msecs_to_jiffies(100)));
-+}
-+
-+static void
-+vc4_reset(struct drm_device *dev)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+
-+ DRM_INFO("Resetting GPU.\n");
-+ vc4_v3d_set_power(vc4, false);
-+ vc4_v3d_set_power(vc4, true);
-+
-+ vc4_irq_reset(dev);
-+
-+ /* Rearm the hangcheck -- another job might have been waiting
-+ * for our hung one to get kicked off, and vc4_irq_reset()
-+ * would have started it.
-+ */
-+ vc4_queue_hangcheck(dev);
-+}
-+
-+static void
-+vc4_reset_work(struct work_struct *work)
-+{
-+ struct vc4_dev *vc4 =
-+ container_of(work, struct vc4_dev, hangcheck.reset_work);
-+
-+ vc4_reset(vc4->dev);
-+}
-+
-+static void
-+vc4_hangcheck_elapsed(unsigned long data)
-+{
-+ struct drm_device *dev = (struct drm_device *)data;
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ uint32_t ct0ca, ct1ca;
-+
-+ /* If idle, we can stop watching for hangs. */
-+ if (list_empty(&vc4->job_list))
-+ return;
-+
-+ ct0ca = V3D_READ(V3D_CTNCA(0));
-+ ct1ca = V3D_READ(V3D_CTNCA(1));
-+
-+ /* If we've made any progress in execution, rearm the timer
-+ * and wait.
-+ */
-+ if (ct0ca != vc4->hangcheck.last_ct0ca ||
-+ ct1ca != vc4->hangcheck.last_ct1ca) {
-+ vc4->hangcheck.last_ct0ca = ct0ca;
-+ vc4->hangcheck.last_ct1ca = ct1ca;
-+ vc4_queue_hangcheck(dev);
-+ return;
-+ }
-+
-+ /* We've gone too long with no progress, reset. This has to
-+ * be done from a work struct, since resetting can sleep and
-+ * this timer hook isn't allowed to.
-+ */
-+ schedule_work(&vc4->hangcheck.reset_work);
-+}
-+
-+static void
-+submit_cl(struct drm_device *dev, uint32_t thread, uint32_t start, uint32_t end)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+
-+ /* Stop any existing thread and set state to "stopped at halt" */
-+ V3D_WRITE(V3D_CTNCS(thread), V3D_CTRUN);
-+ barrier();
-+
-+ V3D_WRITE(V3D_CTNCA(thread), start);
-+ barrier();
-+
-+ /* Set the end address of the control list. Writing this
-+ * register is what starts the job.
-+ */
-+ V3D_WRITE(V3D_CTNEA(thread), end);
-+ barrier();
-+}
-+
-+int
-+vc4_wait_for_seqno(struct drm_device *dev, uint64_t seqno, uint64_t timeout_ns,
-+ bool interruptible)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ int ret = 0;
-+ unsigned long timeout_expire;
-+ DEFINE_WAIT(wait);
-+
-+ if (vc4->finished_seqno >= seqno)
-+ return 0;
-+
-+ if (timeout_ns == 0)
-+ return -ETIME;
-+
-+ timeout_expire = jiffies + nsecs_to_jiffies(timeout_ns);
-+
-+ trace_vc4_wait_for_seqno_begin(dev, seqno, timeout_ns);
-+ for (;;) {
-+ prepare_to_wait(&vc4->job_wait_queue, &wait,
-+ interruptible ? TASK_INTERRUPTIBLE :
-+ TASK_UNINTERRUPTIBLE);
-+
-+ if (interruptible && signal_pending(current)) {
-+ ret = -ERESTARTSYS;
-+ break;
-+ }
-+
-+ if (vc4->finished_seqno >= seqno)
-+ break;
-+
-+ if (timeout_ns != ~0ull) {
-+ if (time_after_eq(jiffies, timeout_expire)) {
-+ ret = -ETIME;
-+ break;
-+ }
-+ schedule_timeout(timeout_expire - jiffies);
-+ } else {
-+ schedule();
-+ }
-+ }
-+
-+ finish_wait(&vc4->job_wait_queue, &wait);
-+ trace_vc4_wait_for_seqno_end(dev, seqno);
-+
-+ if (ret && ret != -ERESTARTSYS) {
-+ DRM_ERROR("timeout waiting for render thread idle\n");
-+ return ret;
-+ }
-+
-+ return 0;
-+}
-+
-+static void
-+vc4_flush_caches(struct drm_device *dev)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+
-+ /* Flush the GPU L2 caches. These caches sit on top of system
-+ * L3 (the 128kb or so shared with the CPU), and are
-+ * non-allocating in the L3.
-+ */
-+ V3D_WRITE(V3D_L2CACTL,
-+ V3D_L2CACTL_L2CCLR);
-+
-+ V3D_WRITE(V3D_SLCACTL,
-+ VC4_SET_FIELD(0xf, V3D_SLCACTL_T1CC) |
-+ VC4_SET_FIELD(0xf, V3D_SLCACTL_T0CC) |
-+ VC4_SET_FIELD(0xf, V3D_SLCACTL_UCC) |
-+ VC4_SET_FIELD(0xf, V3D_SLCACTL_ICC));
-+}
-+
-+/* Sets the registers for the next job to be actually be executed in
-+ * the hardware.
-+ *
-+ * The job_lock should be held during this.
-+ */
-+void
-+vc4_submit_next_job(struct drm_device *dev)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ struct vc4_exec_info *exec = vc4_first_job(vc4);
-+
-+ if (!exec)
-+ return;
-+
-+ vc4_flush_caches(dev);
-+
-+ /* Disable the binner's pre-loaded overflow memory address */
-+ V3D_WRITE(V3D_BPOA, 0);
-+ V3D_WRITE(V3D_BPOS, 0);
-+
-+ if (exec->ct0ca != exec->ct0ea)
-+ submit_cl(dev, 0, exec->ct0ca, exec->ct0ea);
-+ submit_cl(dev, 1, exec->ct1ca, exec->ct1ea);
-+}
-+
-+static void
-+vc4_update_bo_seqnos(struct vc4_exec_info *exec, uint64_t seqno)
-+{
-+ struct vc4_bo *bo;
-+ unsigned i;
-+
-+ for (i = 0; i < exec->bo_count; i++) {
-+ bo = to_vc4_bo(&exec->bo[i].bo->base);
-+ bo->seqno = seqno;
-+ }
-+
-+ list_for_each_entry(bo, &exec->unref_list, unref_head) {
-+ bo->seqno = seqno;
-+ }
-+}
-+
-+/* Queues a struct vc4_exec_info for execution. If no job is
-+ * currently executing, then submits it.
-+ *
-+ * Unlike most GPUs, our hardware only handles one command list at a
-+ * time. To queue multiple jobs at once, we'd need to edit the
-+ * previous command list to have a jump to the new one at the end, and
-+ * then bump the end address. That's a change for a later date,
-+ * though.
-+ */
-+static void
-+vc4_queue_submit(struct drm_device *dev, struct vc4_exec_info *exec)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ uint64_t seqno = ++vc4->emit_seqno;
-+ unsigned long irqflags;
-+
-+ exec->seqno = seqno;
-+ vc4_update_bo_seqnos(exec, seqno);
-+
-+ spin_lock_irqsave(&vc4->job_lock, irqflags);
-+ list_add_tail(&exec->head, &vc4->job_list);
-+
-+ /* If no job was executing, kick ours off. Otherwise, it'll
-+ * get started when the previous job's frame done interrupt
-+ * occurs.
-+ */
-+ if (vc4_first_job(vc4) == exec) {
-+ vc4_submit_next_job(dev);
-+ vc4_queue_hangcheck(dev);
-+ }
-+
-+ spin_unlock_irqrestore(&vc4->job_lock, irqflags);
-+}
-+
-+/**
-+ * Looks up a bunch of GEM handles for BOs and stores the array for
-+ * use in the command validator that actually writes relocated
-+ * addresses pointing to them.
-+ */
-+static int
-+vc4_cl_lookup_bos(struct drm_device *dev,
-+ struct drm_file *file_priv,
-+ struct vc4_exec_info *exec)
-+{
-+ struct drm_vc4_submit_cl *args = exec->args;
-+ uint32_t *handles;
-+ int ret = 0;
-+ int i;
-+
-+ exec->bo_count = args->bo_handle_count;
-+
-+ if (!exec->bo_count) {
-+ /* See comment on bo_index for why we have to check
-+ * this.
-+ */
-+ DRM_ERROR("Rendering requires BOs to validate\n");
-+ return -EINVAL;
-+ }
-+
-+ exec->bo = kcalloc(exec->bo_count, sizeof(struct vc4_bo_exec_state),
-+ GFP_KERNEL);
-+ if (!exec->bo) {
-+ DRM_ERROR("Failed to allocate validated BO pointers\n");
-+ return -ENOMEM;
-+ }
-+
-+ handles = drm_malloc_ab(exec->bo_count, sizeof(uint32_t));
-+ if (!handles) {
-+ DRM_ERROR("Failed to allocate incoming GEM handles\n");
-+ goto fail;
-+ }
-+
-+ ret = copy_from_user(handles,
-+ (void __user *)(uintptr_t)args->bo_handles,
-+ exec->bo_count * sizeof(uint32_t));
-+ if (ret) {
-+ DRM_ERROR("Failed to copy in GEM handles\n");
-+ goto fail;
-+ }
-+
-+ spin_lock(&file_priv->table_lock);
-+ for (i = 0; i < exec->bo_count; i++) {
-+ struct drm_gem_object *bo = idr_find(&file_priv->object_idr,
-+ handles[i]);
-+ if (!bo) {
-+ DRM_ERROR("Failed to look up GEM BO %d: %d\n",
-+ i, handles[i]);
-+ ret = -EINVAL;
-+ spin_unlock(&file_priv->table_lock);
-+ goto fail;
-+ }
-+ drm_gem_object_reference(bo);
-+ exec->bo[i].bo = (struct drm_gem_cma_object *)bo;
-+ }
-+ spin_unlock(&file_priv->table_lock);
-+
-+fail:
-+ kfree(handles);
-+ return 0;
-+}
-+
-+static int
-+vc4_get_bcl(struct drm_device *dev, struct vc4_exec_info *exec)
-+{
-+ struct drm_vc4_submit_cl *args = exec->args;
-+ void *temp = NULL;
-+ void *bin;
-+ int ret = 0;
-+ uint32_t bin_offset = 0;
-+ uint32_t shader_rec_offset = roundup(bin_offset + args->bin_cl_size,
-+ 16);
-+ uint32_t uniforms_offset = shader_rec_offset + args->shader_rec_size;
-+ uint32_t exec_size = uniforms_offset + args->uniforms_size;
-+ uint32_t temp_size = exec_size + (sizeof(struct vc4_shader_state) *
-+ args->shader_rec_count);
-+ struct vc4_bo *bo;
-+
-+ if (uniforms_offset < shader_rec_offset ||
-+ exec_size < uniforms_offset ||
-+ args->shader_rec_count >= (UINT_MAX /
-+ sizeof(struct vc4_shader_state)) ||
-+ temp_size < exec_size) {
-+ DRM_ERROR("overflow in exec arguments\n");
-+ goto fail;
-+ }
-+
-+ /* Allocate space where we'll store the copied in user command lists
-+ * and shader records.
-+ *
-+ * We don't just copy directly into the BOs because we need to
-+ * read the contents back for validation, and I think the
-+ * bo->vaddr is uncached access.
-+ */
-+ temp = kmalloc(temp_size, GFP_KERNEL);
-+ if (!temp) {
-+ DRM_ERROR("Failed to allocate storage for copying "
-+ "in bin/render CLs.\n");
-+ ret = -ENOMEM;
-+ goto fail;
-+ }
-+ bin = temp + bin_offset;
-+ exec->shader_rec_u = temp + shader_rec_offset;
-+ exec->uniforms_u = temp + uniforms_offset;
-+ exec->shader_state = temp + exec_size;
-+ exec->shader_state_size = args->shader_rec_count;
-+
-+ ret = copy_from_user(bin,
-+ (void __user *)(uintptr_t)args->bin_cl,
-+ args->bin_cl_size);
-+ if (ret) {
-+ DRM_ERROR("Failed to copy in bin cl\n");
-+ goto fail;
-+ }
-+
-+ ret = copy_from_user(exec->shader_rec_u,
-+ (void __user *)(uintptr_t)args->shader_rec,
-+ args->shader_rec_size);
-+ if (ret) {
-+ DRM_ERROR("Failed to copy in shader recs\n");
-+ goto fail;
-+ }
-+
-+ ret = copy_from_user(exec->uniforms_u,
-+ (void __user *)(uintptr_t)args->uniforms,
-+ args->uniforms_size);
-+ if (ret) {
-+ DRM_ERROR("Failed to copy in uniforms cl\n");
-+ goto fail;
-+ }
-+
-+ bo = vc4_bo_create(dev, exec_size);
-+ if (!bo) {
-+ DRM_ERROR("Couldn't allocate BO for binning\n");
-+ ret = PTR_ERR(exec->exec_bo);
-+ goto fail;
-+ }
-+ exec->exec_bo = &bo->base;
-+
-+ list_add_tail(&to_vc4_bo(&exec->exec_bo->base)->unref_head,
-+ &exec->unref_list);
-+
-+ exec->ct0ca = exec->exec_bo->paddr + bin_offset;
-+
-+ exec->shader_rec_v = exec->exec_bo->vaddr + shader_rec_offset;
-+ exec->shader_rec_p = exec->exec_bo->paddr + shader_rec_offset;
-+ exec->shader_rec_size = args->shader_rec_size;
-+
-+ exec->uniforms_v = exec->exec_bo->vaddr + uniforms_offset;
-+ exec->uniforms_p = exec->exec_bo->paddr + uniforms_offset;
-+ exec->uniforms_size = args->uniforms_size;
-+
-+ ret = vc4_validate_bin_cl(dev,
-+ exec->exec_bo->vaddr + bin_offset,
-+ bin,
-+ exec);
-+ if (ret)
-+ goto fail;
-+
-+ ret = vc4_validate_shader_recs(dev, exec);
-+
-+fail:
-+ kfree(temp);
-+ return ret;
-+}
-+
-+static void
-+vc4_complete_exec(struct vc4_exec_info *exec)
-+{
-+ unsigned i;
-+
-+ if (exec->bo) {
-+ for (i = 0; i < exec->bo_count; i++)
-+ drm_gem_object_unreference(&exec->bo[i].bo->base);
-+ kfree(exec->bo);
-+ }
-+
-+ while (!list_empty(&exec->unref_list)) {
-+ struct vc4_bo *bo = list_first_entry(&exec->unref_list,
-+ struct vc4_bo, unref_head);
-+ list_del(&bo->unref_head);
-+ drm_gem_object_unreference(&bo->base.base);
-+ }
-+
-+ kfree(exec);
-+}
-+
-+void
-+vc4_job_handle_completed(struct vc4_dev *vc4)
-+{
-+ unsigned long irqflags;
-+ struct vc4_seqno_cb *cb, *cb_temp;
-+
-+ spin_lock_irqsave(&vc4->job_lock, irqflags);
-+ while (!list_empty(&vc4->job_done_list)) {
-+ struct vc4_exec_info *exec =
-+ list_first_entry(&vc4->job_done_list,
-+ struct vc4_exec_info, head);
-+ list_del(&exec->head);
-+
-+ spin_unlock_irqrestore(&vc4->job_lock, irqflags);
-+ vc4_complete_exec(exec);
-+ spin_lock_irqsave(&vc4->job_lock, irqflags);
-+ }
-+ spin_unlock_irqrestore(&vc4->job_lock, irqflags);
-+
-+ list_for_each_entry_safe(cb, cb_temp, &vc4->seqno_cb_list, work.entry) {
-+ if (cb->seqno <= vc4->finished_seqno) {
-+ list_del_init(&cb->work.entry);
-+ schedule_work(&cb->work);
-+ }
-+ }
-+}
-+
-+static void vc4_seqno_cb_work(struct work_struct *work)
-+{
-+ struct vc4_seqno_cb *cb = container_of(work, struct vc4_seqno_cb, work);
-+ cb->func(cb);
-+}
-+
-+int vc4_queue_seqno_cb(struct drm_device *dev,
-+ struct vc4_seqno_cb *cb, uint64_t seqno,
-+ void (*func)(struct vc4_seqno_cb *cb))
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ int ret = 0;
-+
-+ cb->func = func;
-+ INIT_WORK(&cb->work, vc4_seqno_cb_work);
-+
-+ mutex_lock(&dev->struct_mutex);
-+ if (seqno > vc4->finished_seqno) {
-+ cb->seqno = seqno;
-+ list_add_tail(&cb->work.entry, &vc4->seqno_cb_list);
-+ } else {
-+ schedule_work(&cb->work);
-+ }
-+ mutex_unlock(&dev->struct_mutex);
-+
-+ return ret;
-+}
-+
-+/* Scheduled when any job has been completed, this walks the list of
-+ * jobs that had completed and unrefs their BOs and frees their exec
-+ * structs.
-+ */
-+static void
-+vc4_job_done_work(struct work_struct *work)
-+{
-+ struct vc4_dev *vc4 =
-+ container_of(work, struct vc4_dev, job_done_work);
-+ struct drm_device *dev = vc4->dev;
-+
-+ /* Need the struct lock for drm_gem_object_unreference(). */
-+ mutex_lock(&dev->struct_mutex);
-+ vc4_job_handle_completed(vc4);
-+ mutex_unlock(&dev->struct_mutex);
-+}
-+
-+static int
-+vc4_wait_for_seqno_ioctl_helper(struct drm_device *dev,
-+ uint64_t seqno,
-+ uint64_t *timeout_ns)
-+{
-+ unsigned long start = jiffies;
-+ int ret = vc4_wait_for_seqno(dev, seqno, *timeout_ns, true);
-+
-+ if ((ret == -EINTR || ret == -ERESTARTSYS) && *timeout_ns != ~0ull) {
-+ uint64_t delta = jiffies_to_nsecs(jiffies - start);
-+ if (*timeout_ns >= delta)
-+ *timeout_ns -= delta;
-+ }
-+
-+ return ret;
-+}
-+
-+int
-+vc4_wait_seqno_ioctl(struct drm_device *dev, void *data,
-+ struct drm_file *file_priv)
-+{
-+ struct drm_vc4_wait_seqno *args = data;
-+
-+ return vc4_wait_for_seqno_ioctl_helper(dev, args->seqno,
-+ &args->timeout_ns);
-+}
-+
-+int
-+vc4_wait_bo_ioctl(struct drm_device *dev, void *data,
-+ struct drm_file *file_priv)
-+{
-+ int ret;
-+ struct drm_vc4_wait_bo *args = data;
-+ struct drm_gem_object *gem_obj;
-+ struct vc4_bo *bo;
-+
-+ gem_obj = drm_gem_object_lookup(dev, file_priv, args->handle);
-+ if (!gem_obj) {
-+ DRM_ERROR("Failed to look up GEM BO %d\n", args->handle);
-+ return -EINVAL;
-+ }
-+ bo = to_vc4_bo(gem_obj);
-+
-+ ret = vc4_wait_for_seqno_ioctl_helper(dev, bo->seqno, &args->timeout_ns);
-+
-+ drm_gem_object_unreference(gem_obj);
-+ return ret;
-+}
-+
-+/**
-+ * Submits a command list to the VC4.
-+ *
-+ * This is what is called batchbuffer emitting on other hardware.
-+ */
-+int
-+vc4_submit_cl_ioctl(struct drm_device *dev, void *data,
-+ struct drm_file *file_priv)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ struct drm_vc4_submit_cl *args = data;
-+ struct vc4_exec_info *exec;
-+ int ret;
-+
-+ if ((args->flags & ~VC4_SUBMIT_CL_USE_CLEAR_COLOR) != 0) {
-+ DRM_ERROR("Unknown flags: 0x%02x\n", args->flags);
-+ return -EINVAL;
-+ }
-+
-+ exec = kcalloc(1, sizeof(*exec), GFP_KERNEL);
-+ if (!exec) {
-+ DRM_ERROR("malloc failure on exec struct\n");
-+ return -ENOMEM;
-+ }
-+
-+ exec->args = args;
-+ INIT_LIST_HEAD(&exec->unref_list);
-+
-+ mutex_lock(&dev->struct_mutex);
-+
-+ ret = vc4_cl_lookup_bos(dev, file_priv, exec);
-+ if (ret)
-+ goto fail;
-+
-+ if (exec->args->bin_cl_size != 0) {
-+ ret = vc4_get_bcl(dev, exec);
-+ if (ret)
-+ goto fail;
-+ } else {
-+ exec->ct0ca = exec->ct0ea = 0;
-+ }
-+
-+ ret = vc4_get_rcl(dev, exec);
-+ if (ret)
-+ goto fail;
-+
-+ /* Clear this out of the struct we'll be putting in the queue,
-+ * since it's part of our stack.
-+ */
-+ exec->args = NULL;
-+
-+ vc4_queue_submit(dev, exec);
-+
-+ /* Return the seqno for our job. */
-+ args->seqno = vc4->emit_seqno;
-+
-+ mutex_unlock(&dev->struct_mutex);
-+
-+ return 0;
-+
-+fail:
-+ vc4_complete_exec(exec);
-+
-+ mutex_unlock(&dev->struct_mutex);
-+
-+ return ret;
-+}
-+
-+void
-+vc4_gem_init(struct drm_device *dev)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+
-+ INIT_LIST_HEAD(&vc4->job_list);
-+ INIT_LIST_HEAD(&vc4->job_done_list);
-+ INIT_LIST_HEAD(&vc4->seqno_cb_list);
-+ spin_lock_init(&vc4->job_lock);
-+
-+ INIT_WORK(&vc4->hangcheck.reset_work, vc4_reset_work);
-+ setup_timer(&vc4->hangcheck.timer,
-+ vc4_hangcheck_elapsed,
-+ (unsigned long) dev);
-+
-+ INIT_WORK(&vc4->job_done_work, vc4_job_done_work);
-+}
-+
-+void
-+vc4_gem_destroy(struct drm_device *dev)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+
-+ /* Waiting for exec to finish would need to be done before
-+ * unregistering V3D.
-+ */
-+ WARN_ON(vc4->emit_seqno != vc4->finished_seqno);
-+
-+ /* V3D should already have disabled its interrupt and cleared
-+ * the overflow allocation registers. Now free the object.
-+ */
-+ if (vc4->overflow_mem) {
-+ drm_gem_object_unreference_unlocked(&vc4->overflow_mem->base.base);
-+ vc4->overflow_mem = NULL;
-+ }
-+
-+ vc4_bo_cache_destroy(dev);
-+}
---- /dev/null
-+++ b/drivers/gpu/drm/vc4/vc4_irq.c
-@@ -0,0 +1,211 @@
-+/*
-+ * Copyright © 2014 Broadcom
-+ *
-+ * Permission is hereby granted, free of charge, to any person obtaining a
-+ * copy of this software and associated documentation files (the "Software"),
-+ * to deal in the Software without restriction, including without limitation
-+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
-+ * and/or sell copies of the Software, and to permit persons to whom the
-+ * Software is furnished to do so, subject to the following conditions:
-+ *
-+ * The above copyright notice and this permission notice (including the next
-+ * paragraph) shall be included in all copies or substantial portions of the
-+ * Software.
-+ *
-+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
-+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
-+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
-+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
-+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
-+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS
-+ * IN THE SOFTWARE.
-+ */
-+
-+/** DOC: Interrupt management for the V3D engine.
-+ *
-+ * We have an interrupt status register (V3D_INTCTL) which reports
-+ * interrupts, and where writing 1 bits clears those interrupts.
-+ * There are also a pair of interrupt registers
-+ * (V3D_INTENA/V3D_INTDIS) where writing a 1 to their bits enables or
-+ * disables that specific interrupt, and 0s written are ignored
-+ * (reading either one returns the set of enabled interrupts).
-+ *
-+ * When we take a render frame interrupt, we need to wake the
-+ * processes waiting for some frame to be done, and get the next frame
-+ * submitted ASAP (so the hardware doesn't sit idle when there's work
-+ * to do).
-+ *
-+ * When we take the binner out of memory interrupt, we need to
-+ * allocate some new memory and pass it to the binner so that the
-+ * current job can make progress.
-+ */
-+
-+#include "vc4_drv.h"
-+#include "vc4_regs.h"
-+
-+#define V3D_DRIVER_IRQS (V3D_INT_OUTOMEM | \
-+ V3D_INT_FRDONE)
-+
-+DECLARE_WAIT_QUEUE_HEAD(render_wait);
-+
-+static void
-+vc4_overflow_mem_work(struct work_struct *work)
-+{
-+ struct vc4_dev *vc4 =
-+ container_of(work, struct vc4_dev, overflow_mem_work);
-+ struct drm_device *dev = vc4->dev;
-+ struct vc4_bo *bo;
-+
-+ bo = vc4_bo_create(dev, 256 * 1024);
-+ if (!bo) {
-+ DRM_ERROR("Couldn't allocate binner overflow mem\n");
-+ return;
-+ }
-+
-+ /* If there's a job executing currently, then our previous
-+ * overflow allocation is getting used in that job and we need
-+ * to queue it to be released when the job is done. But if no
-+ * job is executing at all, then we can free the old overflow
-+ * object direcctly.
-+ *
-+ * No lock necessary for this pointer since we're the only
-+ * ones that update the pointer, and our workqueue won't
-+ * reenter.
-+ */
-+ if (vc4->overflow_mem) {
-+ struct vc4_exec_info *current_exec;
-+ unsigned long irqflags;
-+
-+ spin_lock_irqsave(&vc4->job_lock, irqflags);
-+ current_exec = vc4_first_job(vc4);
-+ if (current_exec) {
-+ vc4->overflow_mem->seqno = vc4->finished_seqno + 1;
-+ list_add_tail(&vc4->overflow_mem->unref_head,
-+ ¤t_exec->unref_list);
-+ vc4->overflow_mem = NULL;
-+ }
-+ spin_unlock_irqrestore(&vc4->job_lock, irqflags);
-+ }
-+
-+ if (vc4->overflow_mem) {
-+ drm_gem_object_unreference_unlocked(&vc4->overflow_mem->base.base);
-+ }
-+ vc4->overflow_mem = bo;
-+
-+ V3D_WRITE(V3D_BPOA, bo->base.paddr);
-+ V3D_WRITE(V3D_BPOS, bo->base.base.size);
-+ V3D_WRITE(V3D_INTCTL, V3D_INT_OUTOMEM);
-+ V3D_WRITE(V3D_INTENA, V3D_INT_OUTOMEM);
-+}
-+
-+static void
-+vc4_irq_finish_job(struct drm_device *dev)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ struct vc4_exec_info *exec = vc4_first_job(vc4);
-+
-+ if (!exec)
-+ return;
-+
-+ vc4->finished_seqno++;
-+ list_move_tail(&exec->head, &vc4->job_done_list);
-+ vc4_submit_next_job(dev);
-+
-+ wake_up_all(&vc4->job_wait_queue);
-+ schedule_work(&vc4->job_done_work);
-+}
-+
-+irqreturn_t
-+vc4_irq(int irq, void *arg)
-+{
-+ struct drm_device *dev = arg;
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ uint32_t intctl;
-+ irqreturn_t status = IRQ_NONE;
-+
-+ barrier();
-+ intctl = V3D_READ(V3D_INTCTL);
-+
-+ /* Acknowledge the interrupts we're handling here. The render
-+ * frame done interrupt will be cleared, while OUTOMEM will
-+ * stay high until the underlying cause is cleared.
-+ */
-+ V3D_WRITE(V3D_INTCTL, intctl);
-+
-+ if (intctl & V3D_INT_OUTOMEM) {
-+ /* Disable OUTOMEM until the work is done. */
-+ V3D_WRITE(V3D_INTDIS, V3D_INT_OUTOMEM);
-+ schedule_work(&vc4->overflow_mem_work);
-+ status = IRQ_HANDLED;
-+ }
-+
-+ if (intctl & V3D_INT_FRDONE) {
-+ spin_lock(&vc4->job_lock);
-+ vc4_irq_finish_job(dev);
-+ spin_unlock(&vc4->job_lock);
-+ status = IRQ_HANDLED;
-+ }
-+
-+ return status;
-+}
-+
-+void
-+vc4_irq_preinstall(struct drm_device *dev)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+
-+ init_waitqueue_head(&vc4->job_wait_queue);
-+ INIT_WORK(&vc4->overflow_mem_work, vc4_overflow_mem_work);
-+
-+ /* Clear any pending interrupts someone might have left around
-+ * for us.
-+ */
-+ V3D_WRITE(V3D_INTCTL, V3D_DRIVER_IRQS);
-+}
-+
-+int
-+vc4_irq_postinstall(struct drm_device *dev)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+
-+ /* Enable both the render done and out of memory interrupts. */
-+ V3D_WRITE(V3D_INTENA, V3D_DRIVER_IRQS);
-+
-+ return 0;
-+}
-+
-+void
-+vc4_irq_uninstall(struct drm_device *dev)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+
-+ /* Disable sending interrupts for our driver's IRQs. */
-+ V3D_WRITE(V3D_INTDIS, V3D_DRIVER_IRQS);
-+
-+ /* Clear any pending interrupts we might have left. */
-+ V3D_WRITE(V3D_INTCTL, V3D_DRIVER_IRQS);
-+
-+ cancel_work_sync(&vc4->overflow_mem_work);
-+}
-+
-+/** Reinitializes interrupt registers when a GPU reset is performed. */
-+void vc4_irq_reset(struct drm_device *dev)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ unsigned long irqflags;
-+
-+ /* Acknowledge any stale IRQs. */
-+ V3D_WRITE(V3D_INTCTL, V3D_DRIVER_IRQS);
-+
-+ /*
-+ * Turn all our interrupts on. Binner out of memory is the
-+ * only one we expect to trigger at this point, since we've
-+ * just come from poweron and haven't supplied any overflow
-+ * memory yet.
-+ */
-+ V3D_WRITE(V3D_INTENA, V3D_DRIVER_IRQS);
-+
-+ spin_lock_irqsave(&vc4->job_lock, irqflags);
-+ vc4_irq_finish_job(dev);
-+ spin_unlock_irqrestore(&vc4->job_lock, irqflags);
-+}
---- a/drivers/gpu/drm/vc4/vc4_kms.c
-+++ b/drivers/gpu/drm/vc4/vc4_kms.c
-@@ -15,6 +15,7 @@
- */
-
- #include "drm_crtc.h"
-+#include "drm_atomic.h"
- #include "drm_atomic_helper.h"
- #include "drm_crtc_helper.h"
- #include "drm_plane_helper.h"
-@@ -29,10 +30,151 @@ static void vc4_output_poll_changed(stru
- drm_fbdev_cma_hotplug_event(vc4->fbdev);
- }
-
-+struct vc4_commit {
-+ struct drm_device *dev;
-+ struct drm_atomic_state *state;
-+ struct vc4_seqno_cb cb;
-+};
-+
-+static void
-+vc4_atomic_complete_commit(struct vc4_commit *c)
-+{
-+ struct drm_atomic_state *state = c->state;
-+ struct drm_device *dev = state->dev;
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+
-+ drm_atomic_helper_commit_modeset_disables(dev, state);
-+
-+ drm_atomic_helper_commit_planes(dev, state);
-+
-+ drm_atomic_helper_commit_modeset_enables(dev, state);
-+
-+ drm_atomic_helper_wait_for_vblanks(dev, state);
-+
-+ drm_atomic_helper_cleanup_planes(dev, state);
-+
-+ drm_atomic_state_free(state);
-+
-+ up(&vc4->async_modeset);
-+
-+ kfree(c);
-+}
-+
-+static void
-+vc4_atomic_complete_commit_seqno_cb(struct vc4_seqno_cb *cb)
-+{
-+ struct vc4_commit *c = container_of(cb, struct vc4_commit, cb);
-+
-+ vc4_atomic_complete_commit(c);
-+}
-+
-+static struct vc4_commit *commit_init(struct drm_atomic_state *state)
-+{
-+ struct vc4_commit *c = kzalloc(sizeof(*c), GFP_KERNEL);
-+
-+ if (!c)
-+ return NULL;
-+ c->dev = state->dev;
-+ c->state = state;
-+
-+ return c;
-+}
-+
-+/**
-+ * vc4_atomic_commit - commit validated state object
-+ * @dev: DRM device
-+ * @state: the driver state object
-+ * @async: asynchronous commit
-+ *
-+ * This function commits a with drm_atomic_helper_check() pre-validated state
-+ * object. This can still fail when e.g. the framebuffer reservation fails. For
-+ * now this doesn't implement asynchronous commits.
-+ *
-+ * RETURNS
-+ * Zero for success or -errno.
-+ */
-+static int vc4_atomic_commit(struct drm_device *dev,
-+ struct drm_atomic_state *state,
-+ bool async)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ int ret;
-+ int i;
-+ uint64_t wait_seqno = 0;
-+ struct vc4_commit *c;
-+
-+ c = commit_init(state);
-+ if (!c)
-+ return -ENOMEM;
-+
-+ /* Make sure that any outstanding modesets have finished. */
-+ ret = down_interruptible(&vc4->async_modeset);
-+ if (ret) {
-+ kfree(c);
-+ return ret;
-+ }
-+
-+ ret = drm_atomic_helper_prepare_planes(dev, state);
-+ if (ret) {
-+ kfree(c);
-+ up(&vc4->async_modeset);
-+ return ret;
-+ }
-+
-+ for (i = 0; i < dev->mode_config.num_total_plane; i++) {
-+ struct drm_plane *plane = state->planes[i];
-+ struct drm_plane_state *new_state = state->plane_states[i];
-+
-+ if (!plane)
-+ continue;
-+
-+ if ((plane->state->fb != new_state->fb) && new_state->fb) {
-+ struct drm_gem_cma_object *cma_bo =
-+ drm_fb_cma_get_gem_obj(new_state->fb, 0);
-+ struct vc4_bo *bo = to_vc4_bo(&cma_bo->base);
-+ wait_seqno = max(bo->seqno, wait_seqno);
-+ }
-+ }
-+
-+ /*
-+ * This is the point of no return - everything below never fails except
-+ * when the hw goes bonghits. Which means we can commit the new state on
-+ * the software side now.
-+ */
-+
-+ drm_atomic_helper_swap_state(dev, state);
-+
-+ /*
-+ * Everything below can be run asynchronously without the need to grab
-+ * any modeset locks at all under one condition: It must be guaranteed
-+ * that the asynchronous work has either been cancelled (if the driver
-+ * supports it, which at least requires that the framebuffers get
-+ * cleaned up with drm_atomic_helper_cleanup_planes()) or completed
-+ * before the new state gets committed on the software side with
-+ * drm_atomic_helper_swap_state().
-+ *
-+ * This scheme allows new atomic state updates to be prepared and
-+ * checked in parallel to the asynchronous completion of the previous
-+ * update. Which is important since compositors need to figure out the
-+ * composition of the next frame right after having submitted the
-+ * current layout.
-+ */
-+
-+ if (async) {
-+ vc4_queue_seqno_cb(dev, &c->cb, wait_seqno,
-+ vc4_atomic_complete_commit_seqno_cb);
-+ } else {
-+ vc4_wait_for_seqno(dev, wait_seqno, ~0ull, false);
-+ vc4_atomic_complete_commit(c);
-+ }
-+
-+ return 0;
-+}
-+
- static const struct drm_mode_config_funcs vc4_mode_funcs = {
- .output_poll_changed = vc4_output_poll_changed,
- .atomic_check = drm_atomic_helper_check,
-- .atomic_commit = drm_atomic_helper_commit,
-+ .atomic_commit = vc4_atomic_commit,
- .fb_create = drm_fb_cma_create,
- };
-
-@@ -41,6 +183,8 @@ int vc4_kms_load(struct drm_device *dev)
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- int ret;
-
-+ sema_init(&vc4->async_modeset, 1);
-+
- ret = drm_vblank_init(dev, dev->mode_config.num_crtc);
- if (ret < 0) {
- dev_err(dev->dev, "failed to initialize vblank\n");
-@@ -51,6 +195,8 @@ int vc4_kms_load(struct drm_device *dev)
- dev->mode_config.max_height = 2048;
- dev->mode_config.funcs = &vc4_mode_funcs;
- dev->mode_config.preferred_depth = 24;
-+ dev->mode_config.async_page_flip = true;
-+
- dev->vblank_disable_allowed = true;
-
- drm_mode_config_reset(dev);
---- /dev/null
-+++ b/drivers/gpu/drm/vc4/vc4_packet.h
-@@ -0,0 +1,384 @@
-+/*
-+ * Copyright © 2014 Broadcom
-+ *
-+ * Permission is hereby granted, free of charge, to any person obtaining a
-+ * copy of this software and associated documentation files (the "Software"),
-+ * to deal in the Software without restriction, including without limitation
-+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
-+ * and/or sell copies of the Software, and to permit persons to whom the
-+ * Software is furnished to do so, subject to the following conditions:
-+ *
-+ * The above copyright notice and this permission notice (including the next
-+ * paragraph) shall be included in all copies or substantial portions of the
-+ * Software.
-+ *
-+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
-+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
-+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
-+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
-+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
-+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS
-+ * IN THE SOFTWARE.
-+ */
-+
-+#ifndef VC4_PACKET_H
-+#define VC4_PACKET_H
-+
-+#include "vc4_regs.h" /* for VC4_MASK, VC4_GET_FIELD, VC4_SET_FIELD */
-+
-+enum vc4_packet {
-+ VC4_PACKET_HALT = 0,
-+ VC4_PACKET_NOP = 1,
-+
-+ VC4_PACKET_FLUSH = 4,
-+ VC4_PACKET_FLUSH_ALL = 5,
-+ VC4_PACKET_START_TILE_BINNING = 6,
-+ VC4_PACKET_INCREMENT_SEMAPHORE = 7,
-+ VC4_PACKET_WAIT_ON_SEMAPHORE = 8,
-+
-+ VC4_PACKET_BRANCH = 16,
-+ VC4_PACKET_BRANCH_TO_SUB_LIST = 17,
-+
-+ VC4_PACKET_STORE_MS_TILE_BUFFER = 24,
-+ VC4_PACKET_STORE_MS_TILE_BUFFER_AND_EOF = 25,
-+ VC4_PACKET_STORE_FULL_RES_TILE_BUFFER = 26,
-+ VC4_PACKET_LOAD_FULL_RES_TILE_BUFFER = 27,
-+ VC4_PACKET_STORE_TILE_BUFFER_GENERAL = 28,
-+ VC4_PACKET_LOAD_TILE_BUFFER_GENERAL = 29,
-+
-+ VC4_PACKET_GL_INDEXED_PRIMITIVE = 32,
-+ VC4_PACKET_GL_ARRAY_PRIMITIVE = 33,
-+
-+ VC4_PACKET_COMPRESSED_PRIMITIVE = 48,
-+ VC4_PACKET_CLIPPED_COMPRESSED_PRIMITIVE = 49,
-+
-+ VC4_PACKET_PRIMITIVE_LIST_FORMAT = 56,
-+
-+ VC4_PACKET_GL_SHADER_STATE = 64,
-+ VC4_PACKET_NV_SHADER_STATE = 65,
-+ VC4_PACKET_VG_SHADER_STATE = 66,
-+
-+ VC4_PACKET_CONFIGURATION_BITS = 96,
-+ VC4_PACKET_FLAT_SHADE_FLAGS = 97,
-+ VC4_PACKET_POINT_SIZE = 98,
-+ VC4_PACKET_LINE_WIDTH = 99,
-+ VC4_PACKET_RHT_X_BOUNDARY = 100,
-+ VC4_PACKET_DEPTH_OFFSET = 101,
-+ VC4_PACKET_CLIP_WINDOW = 102,
-+ VC4_PACKET_VIEWPORT_OFFSET = 103,
-+ VC4_PACKET_Z_CLIPPING = 104,
-+ VC4_PACKET_CLIPPER_XY_SCALING = 105,
-+ VC4_PACKET_CLIPPER_Z_SCALING = 106,
-+
-+ VC4_PACKET_TILE_BINNING_MODE_CONFIG = 112,
-+ VC4_PACKET_TILE_RENDERING_MODE_CONFIG = 113,
-+ VC4_PACKET_CLEAR_COLORS = 114,
-+ VC4_PACKET_TILE_COORDINATES = 115,
-+
-+ /* Not an actual hardware packet -- this is what we use to put
-+ * references to GEM bos in the command stream, since we need the u32
-+ * int the actual address packet in order to store the offset from the
-+ * start of the BO.
-+ */
-+ VC4_PACKET_GEM_HANDLES = 254,
-+} __attribute__ ((__packed__));
-+
-+#define VC4_PACKET_HALT_SIZE 1
-+#define VC4_PACKET_NOP_SIZE 1
-+#define VC4_PACKET_FLUSH_SIZE 1
-+#define VC4_PACKET_FLUSH_ALL_SIZE 1
-+#define VC4_PACKET_START_TILE_BINNING_SIZE 1
-+#define VC4_PACKET_INCREMENT_SEMAPHORE_SIZE 1
-+#define VC4_PACKET_WAIT_ON_SEMAPHORE_SIZE 1
-+#define VC4_PACKET_BRANCH_SIZE 5
-+#define VC4_PACKET_BRANCH_TO_SUB_LIST_SIZE 5
-+#define VC4_PACKET_STORE_MS_TILE_BUFFER_SIZE 1
-+#define VC4_PACKET_STORE_MS_TILE_BUFFER_AND_EOF_SIZE 1
-+#define VC4_PACKET_STORE_FULL_RES_TILE_BUFFER_SIZE 5
-+#define VC4_PACKET_LOAD_FULL_RES_TILE_BUFFER_SIZE 5
-+#define VC4_PACKET_STORE_TILE_BUFFER_GENERAL_SIZE 7
-+#define VC4_PACKET_LOAD_TILE_BUFFER_GENERAL_SIZE 7
-+#define VC4_PACKET_GL_INDEXED_PRIMITIVE_SIZE 14
-+#define VC4_PACKET_GL_ARRAY_PRIMITIVE_SIZE 10
-+#define VC4_PACKET_COMPRESSED_PRIMITIVE_SIZE 1
-+#define VC4_PACKET_CLIPPED_COMPRESSED_PRIMITIVE_SIZE 1
-+#define VC4_PACKET_PRIMITIVE_LIST_FORMAT_SIZE 2
-+#define VC4_PACKET_GL_SHADER_STATE_SIZE 5
-+#define VC4_PACKET_NV_SHADER_STATE_SIZE 5
-+#define VC4_PACKET_VG_SHADER_STATE_SIZE 5
-+#define VC4_PACKET_CONFIGURATION_BITS_SIZE 4
-+#define VC4_PACKET_FLAT_SHADE_FLAGS_SIZE 5
-+#define VC4_PACKET_POINT_SIZE_SIZE 5
-+#define VC4_PACKET_LINE_WIDTH_SIZE 5
-+#define VC4_PACKET_RHT_X_BOUNDARY_SIZE 3
-+#define VC4_PACKET_DEPTH_OFFSET_SIZE 5
-+#define VC4_PACKET_CLIP_WINDOW_SIZE 9
-+#define VC4_PACKET_VIEWPORT_OFFSET_SIZE 5
-+#define VC4_PACKET_Z_CLIPPING_SIZE 9
-+#define VC4_PACKET_CLIPPER_XY_SCALING_SIZE 9
-+#define VC4_PACKET_CLIPPER_Z_SCALING_SIZE 9
-+#define VC4_PACKET_TILE_BINNING_MODE_CONFIG_SIZE 16
-+#define VC4_PACKET_TILE_RENDERING_MODE_CONFIG_SIZE 11
-+#define VC4_PACKET_CLEAR_COLORS_SIZE 14
-+#define VC4_PACKET_TILE_COORDINATES_SIZE 3
-+#define VC4_PACKET_GEM_HANDLES_SIZE 9
-+
-+/** @{
-+ * Bits used by packets like VC4_PACKET_STORE_TILE_BUFFER_GENERAL and
-+ * VC4_PACKET_TILE_RENDERING_MODE_CONFIG.
-+*/
-+#define VC4_TILING_FORMAT_LINEAR 0
-+#define VC4_TILING_FORMAT_T 1
-+#define VC4_TILING_FORMAT_LT 2
-+/** @} */
-+
-+/** @{
-+ *
-+ * low bits of VC4_PACKET_STORE_FULL_RES_TILE_BUFFER and
-+ * VC4_PACKET_LOAD_FULL_RES_TILE_BUFFER.
-+ */
-+#define VC4_LOADSTORE_FULL_RES_EOF (1 << 3)
-+#define VC4_LOADSTORE_FULL_RES_DISABLE_CLEAR_ALL (1 << 2)
-+#define VC4_LOADSTORE_FULL_RES_DISABLE_ZS (1 << 1)
-+#define VC4_LOADSTORE_FULL_RES_DISABLE_COLOR (1 << 0)
-+
-+/** @{
-+ *
-+ * byte 2 of VC4_PACKET_STORE_TILE_BUFFER_GENERAL and
-+ * VC4_PACKET_LOAD_TILE_BUFFER_GENERAL (low bits of the address)
-+ */
-+
-+#define VC4_LOADSTORE_TILE_BUFFER_EOF (1 << 3)
-+#define VC4_LOADSTORE_TILE_BUFFER_DISABLE_FULL_VG_MASK (1 << 2)
-+#define VC4_LOADSTORE_TILE_BUFFER_DISABLE_FULL_ZS (1 << 1)
-+#define VC4_LOADSTORE_TILE_BUFFER_DISABLE_FULL_COLOR (1 << 0)
-+
-+/** @} */
-+
-+/** @{
-+ *
-+ * byte 0-1 of VC4_PACKET_STORE_TILE_BUFFER_GENERAL and
-+ * VC4_PACKET_LOAD_TILE_BUFFER_GENERAL
-+ */
-+#define VC4_STORE_TILE_BUFFER_DISABLE_VG_MASK_CLEAR (1 << 15)
-+#define VC4_STORE_TILE_BUFFER_DISABLE_ZS_CLEAR (1 << 14)
-+#define VC4_STORE_TILE_BUFFER_DISABLE_COLOR_CLEAR (1 << 13)
-+#define VC4_STORE_TILE_BUFFER_DISABLE_SWAP (1 << 12)
-+
-+#define VC4_LOADSTORE_TILE_BUFFER_FORMAT_MASK VC4_MASK(9, 8)
-+#define VC4_LOADSTORE_TILE_BUFFER_FORMAT_SHIFT 8
-+#define VC4_LOADSTORE_TILE_BUFFER_RGBA8888 0
-+#define VC4_LOADSTORE_TILE_BUFFER_BGR565_DITHER 1
-+#define VC4_LOADSTORE_TILE_BUFFER_BGR565 2
-+/** @} */
-+
-+/** @{
-+ *
-+ * byte 0 of VC4_PACKET_STORE_TILE_BUFFER_GENERAL and
-+ * VC4_PACKET_LOAD_TILE_BUFFER_GENERAL
-+ */
-+#define VC4_STORE_TILE_BUFFER_MODE_MASK VC4_MASK(7, 6)
-+#define VC4_STORE_TILE_BUFFER_MODE_SHIFT 6
-+#define VC4_STORE_TILE_BUFFER_MODE_SAMPLE0 (0 << 6)
-+#define VC4_STORE_TILE_BUFFER_MODE_DECIMATE_X4 (1 << 6)
-+#define VC4_STORE_TILE_BUFFER_MODE_DECIMATE_X16 (2 << 6)
-+
-+/** The values of the field are VC4_TILING_FORMAT_* */
-+#define VC4_LOADSTORE_TILE_BUFFER_TILING_MASK VC4_MASK(5, 4)
-+#define VC4_LOADSTORE_TILE_BUFFER_TILING_SHIFT 4
-+
-+#define VC4_LOADSTORE_TILE_BUFFER_BUFFER_MASK VC4_MASK(2, 0)
-+#define VC4_LOADSTORE_TILE_BUFFER_BUFFER_SHIFT 0
-+#define VC4_LOADSTORE_TILE_BUFFER_NONE 0
-+#define VC4_LOADSTORE_TILE_BUFFER_COLOR 1
-+#define VC4_LOADSTORE_TILE_BUFFER_ZS 2
-+#define VC4_LOADSTORE_TILE_BUFFER_Z 3
-+#define VC4_LOADSTORE_TILE_BUFFER_VG_MASK 4
-+#define VC4_LOADSTORE_TILE_BUFFER_FULL 5
-+/** @} */
-+
-+#define VC4_INDEX_BUFFER_U8 (0 << 4)
-+#define VC4_INDEX_BUFFER_U16 (1 << 4)
-+
-+/* This flag is only present in NV shader state. */
-+#define VC4_SHADER_FLAG_SHADED_CLIP_COORDS (1 << 3)
-+#define VC4_SHADER_FLAG_ENABLE_CLIPPING (1 << 2)
-+#define VC4_SHADER_FLAG_VS_POINT_SIZE (1 << 1)
-+#define VC4_SHADER_FLAG_FS_SINGLE_THREAD (1 << 0)
-+
-+/** @{ byte 2 of config bits. */
-+#define VC4_CONFIG_BITS_EARLY_Z_UPDATE (1 << 1)
-+#define VC4_CONFIG_BITS_EARLY_Z (1 << 0)
-+/** @} */
-+
-+/** @{ byte 1 of config bits. */
-+#define VC4_CONFIG_BITS_Z_UPDATE (1 << 7)
-+/** same values in this 3-bit field as PIPE_FUNC_* */
-+#define VC4_CONFIG_BITS_DEPTH_FUNC_SHIFT 4
-+#define VC4_CONFIG_BITS_COVERAGE_READ_LEAVE (1 << 3)
-+
-+#define VC4_CONFIG_BITS_COVERAGE_UPDATE_NONZERO (0 << 1)
-+#define VC4_CONFIG_BITS_COVERAGE_UPDATE_ODD (1 << 1)
-+#define VC4_CONFIG_BITS_COVERAGE_UPDATE_OR (2 << 1)
-+#define VC4_CONFIG_BITS_COVERAGE_UPDATE_ZERO (3 << 1)
-+
-+#define VC4_CONFIG_BITS_COVERAGE_PIPE_SELECT (1 << 0)
-+/** @} */
-+
-+/** @{ byte 0 of config bits. */
-+#define VC4_CONFIG_BITS_RASTERIZER_OVERSAMPLE_NONE (0 << 6)
-+#define VC4_CONFIG_BITS_RASTERIZER_OVERSAMPLE_4X (1 << 6)
-+#define VC4_CONFIG_BITS_RASTERIZER_OVERSAMPLE_16X (2 << 6)
-+
-+#define VC4_CONFIG_BITS_AA_POINTS_AND_LINES (1 << 4)
-+#define VC4_CONFIG_BITS_ENABLE_DEPTH_OFFSET (1 << 3)
-+#define VC4_CONFIG_BITS_CW_PRIMITIVES (1 << 2)
-+#define VC4_CONFIG_BITS_ENABLE_PRIM_BACK (1 << 1)
-+#define VC4_CONFIG_BITS_ENABLE_PRIM_FRONT (1 << 0)
-+/** @} */
-+
-+/** @{ bits in the last u8 of VC4_PACKET_TILE_BINNING_MODE_CONFIG */
-+#define VC4_BIN_CONFIG_DB_NON_MS (1 << 7)
-+
-+#define VC4_BIN_CONFIG_ALLOC_BLOCK_SIZE_MASK VC4_MASK(6, 5)
-+#define VC4_BIN_CONFIG_ALLOC_BLOCK_SIZE_SHIFT 5
-+#define VC4_BIN_CONFIG_ALLOC_BLOCK_SIZE_32 0
-+#define VC4_BIN_CONFIG_ALLOC_BLOCK_SIZE_64 1
-+#define VC4_BIN_CONFIG_ALLOC_BLOCK_SIZE_128 2
-+#define VC4_BIN_CONFIG_ALLOC_BLOCK_SIZE_256 3
-+
-+#define VC4_BIN_CONFIG_ALLOC_INIT_BLOCK_SIZE_MASK VC4_MASK(4, 3)
-+#define VC4_BIN_CONFIG_ALLOC_INIT_BLOCK_SIZE_SHIFT 3
-+#define VC4_BIN_CONFIG_ALLOC_INIT_BLOCK_SIZE_32 0
-+#define VC4_BIN_CONFIG_ALLOC_INIT_BLOCK_SIZE_64 1
-+#define VC4_BIN_CONFIG_ALLOC_INIT_BLOCK_SIZE_128 2
-+#define VC4_BIN_CONFIG_ALLOC_INIT_BLOCK_SIZE_256 3
-+
-+#define VC4_BIN_CONFIG_AUTO_INIT_TSDA (1 << 2)
-+#define VC4_BIN_CONFIG_TILE_BUFFER_64BIT (1 << 1)
-+#define VC4_BIN_CONFIG_MS_MODE_4X (1 << 0)
-+/** @} */
-+
-+/** @{ bits in the last u16 of VC4_PACKET_TILE_RENDERING_MODE_CONFIG */
-+#define VC4_RENDER_CONFIG_DB_NON_MS (1 << 12)
-+#define VC4_RENDER_CONFIG_EARLY_Z_COVERAGE_DISABLE (1 << 11)
-+#define VC4_RENDER_CONFIG_EARLY_Z_DIRECTION_G (1 << 10)
-+#define VC4_RENDER_CONFIG_COVERAGE_MODE (1 << 9)
-+#define VC4_RENDER_CONFIG_ENABLE_VG_MASK (1 << 8)
-+
-+/** The values of the field are VC4_TILING_FORMAT_* */
-+#define VC4_RENDER_CONFIG_MEMORY_FORMAT_MASK VC4_MASK(7, 6)
-+#define VC4_RENDER_CONFIG_MEMORY_FORMAT_SHIFT 6
-+
-+#define VC4_RENDER_CONFIG_DECIMATE_MODE_1X (0 << 4)
-+#define VC4_RENDER_CONFIG_DECIMATE_MODE_4X (1 << 4)
-+#define VC4_RENDER_CONFIG_DECIMATE_MODE_16X (2 << 4)
-+
-+#define VC4_RENDER_CONFIG_FORMAT_MASK VC4_MASK(3, 2)
-+#define VC4_RENDER_CONFIG_FORMAT_SHIFT 2
-+#define VC4_RENDER_CONFIG_FORMAT_BGR565_DITHERED 0
-+#define VC4_RENDER_CONFIG_FORMAT_RGBA8888 1
-+#define VC4_RENDER_CONFIG_FORMAT_BGR565 2
-+
-+#define VC4_RENDER_CONFIG_TILE_BUFFER_64BIT (1 << 1)
-+#define VC4_RENDER_CONFIG_MS_MODE_4X (1 << 0)
-+
-+#define VC4_PRIMITIVE_LIST_FORMAT_16_INDEX (1 << 4)
-+#define VC4_PRIMITIVE_LIST_FORMAT_32_XY (3 << 4)
-+#define VC4_PRIMITIVE_LIST_FORMAT_TYPE_POINTS (0 << 0)
-+#define VC4_PRIMITIVE_LIST_FORMAT_TYPE_LINES (1 << 0)
-+#define VC4_PRIMITIVE_LIST_FORMAT_TYPE_TRIANGLES (2 << 0)
-+#define VC4_PRIMITIVE_LIST_FORMAT_TYPE_RHT (3 << 0)
-+
-+enum vc4_texture_data_type {
-+ VC4_TEXTURE_TYPE_RGBA8888 = 0,
-+ VC4_TEXTURE_TYPE_RGBX8888 = 1,
-+ VC4_TEXTURE_TYPE_RGBA4444 = 2,
-+ VC4_TEXTURE_TYPE_RGBA5551 = 3,
-+ VC4_TEXTURE_TYPE_RGB565 = 4,
-+ VC4_TEXTURE_TYPE_LUMINANCE = 5,
-+ VC4_TEXTURE_TYPE_ALPHA = 6,
-+ VC4_TEXTURE_TYPE_LUMALPHA = 7,
-+ VC4_TEXTURE_TYPE_ETC1 = 8,
-+ VC4_TEXTURE_TYPE_S16F = 9,
-+ VC4_TEXTURE_TYPE_S8 = 10,
-+ VC4_TEXTURE_TYPE_S16 = 11,
-+ VC4_TEXTURE_TYPE_BW1 = 12,
-+ VC4_TEXTURE_TYPE_A4 = 13,
-+ VC4_TEXTURE_TYPE_A1 = 14,
-+ VC4_TEXTURE_TYPE_RGBA64 = 15,
-+ VC4_TEXTURE_TYPE_RGBA32R = 16,
-+ VC4_TEXTURE_TYPE_YUV422R = 17,
-+};
-+
-+#define VC4_TEX_P0_OFFSET_MASK VC4_MASK(31, 12)
-+#define VC4_TEX_P0_OFFSET_SHIFT 12
-+#define VC4_TEX_P0_CSWIZ_MASK VC4_MASK(11, 10)
-+#define VC4_TEX_P0_CSWIZ_SHIFT 10
-+#define VC4_TEX_P0_CMMODE_MASK VC4_MASK(9, 9)
-+#define VC4_TEX_P0_CMMODE_SHIFT 9
-+#define VC4_TEX_P0_FLIPY_MASK VC4_MASK(8, 8)
-+#define VC4_TEX_P0_FLIPY_SHIFT 8
-+#define VC4_TEX_P0_TYPE_MASK VC4_MASK(7, 4)
-+#define VC4_TEX_P0_TYPE_SHIFT 4
-+#define VC4_TEX_P0_MIPLVLS_MASK VC4_MASK(3, 0)
-+#define VC4_TEX_P0_MIPLVLS_SHIFT 0
-+
-+#define VC4_TEX_P1_TYPE4_MASK VC4_MASK(31, 31)
-+#define VC4_TEX_P1_TYPE4_SHIFT 31
-+#define VC4_TEX_P1_HEIGHT_MASK VC4_MASK(30, 20)
-+#define VC4_TEX_P1_HEIGHT_SHIFT 20
-+#define VC4_TEX_P1_ETCFLIP_MASK VC4_MASK(19, 19)
-+#define VC4_TEX_P1_ETCFLIP_SHIFT 19
-+#define VC4_TEX_P1_WIDTH_MASK VC4_MASK(18, 8)
-+#define VC4_TEX_P1_WIDTH_SHIFT 8
-+
-+#define VC4_TEX_P1_MAGFILT_MASK VC4_MASK(7, 7)
-+#define VC4_TEX_P1_MAGFILT_SHIFT 7
-+# define VC4_TEX_P1_MAGFILT_LINEAR 0
-+# define VC4_TEX_P1_MAGFILT_NEAREST 1
-+
-+#define VC4_TEX_P1_MINFILT_MASK VC4_MASK(6, 4)
-+#define VC4_TEX_P1_MINFILT_SHIFT 4
-+# define VC4_TEX_P1_MINFILT_LINEAR 0
-+# define VC4_TEX_P1_MINFILT_NEAREST 1
-+# define VC4_TEX_P1_MINFILT_NEAR_MIP_NEAR 2
-+# define VC4_TEX_P1_MINFILT_NEAR_MIP_LIN 3
-+# define VC4_TEX_P1_MINFILT_LIN_MIP_NEAR 4
-+# define VC4_TEX_P1_MINFILT_LIN_MIP_LIN 5
-+
-+#define VC4_TEX_P1_WRAP_T_MASK VC4_MASK(3, 2)
-+#define VC4_TEX_P1_WRAP_T_SHIFT 2
-+#define VC4_TEX_P1_WRAP_S_MASK VC4_MASK(1, 0)
-+#define VC4_TEX_P1_WRAP_S_SHIFT 0
-+# define VC4_TEX_P1_WRAP_REPEAT 0
-+# define VC4_TEX_P1_WRAP_CLAMP 1
-+# define VC4_TEX_P1_WRAP_MIRROR 2
-+# define VC4_TEX_P1_WRAP_BORDER 3
-+
-+#define VC4_TEX_P2_PTYPE_MASK VC4_MASK(31, 30)
-+#define VC4_TEX_P2_PTYPE_SHIFT 30
-+# define VC4_TEX_P2_PTYPE_IGNORED 0
-+# define VC4_TEX_P2_PTYPE_CUBE_MAP_STRIDE 1
-+# define VC4_TEX_P2_PTYPE_CHILD_IMAGE_DIMENSIONS 2
-+# define VC4_TEX_P2_PTYPE_CHILD_IMAGE_OFFSETS 3
-+
-+/* VC4_TEX_P2_PTYPE_CUBE_MAP_STRIDE bits */
-+#define VC4_TEX_P2_CMST_MASK VC4_MASK(29, 12)
-+#define VC4_TEX_P2_CMST_SHIFT 12
-+#define VC4_TEX_P2_BSLOD_MASK VC4_MASK(0, 0)
-+#define VC4_TEX_P2_BSLOD_SHIFT 0
-+
-+/* VC4_TEX_P2_PTYPE_CHILD_IMAGE_DIMENSIONS */
-+#define VC4_TEX_P2_CHEIGHT_MASK VC4_MASK(22, 12)
-+#define VC4_TEX_P2_CHEIGHT_SHIFT 12
-+#define VC4_TEX_P2_CWIDTH_MASK VC4_MASK(10, 0)
-+#define VC4_TEX_P2_CWIDTH_SHIFT 0
-+
-+/* VC4_TEX_P2_PTYPE_CHILD_IMAGE_OFFSETS */
-+#define VC4_TEX_P2_CYOFF_MASK VC4_MASK(22, 12)
-+#define VC4_TEX_P2_CYOFF_SHIFT 12
-+#define VC4_TEX_P2_CXOFF_MASK VC4_MASK(10, 0)
-+#define VC4_TEX_P2_CXOFF_SHIFT 0
-+
-+#endif /* VC4_PACKET_H */
---- a/drivers/gpu/drm/vc4/vc4_plane.c
-+++ b/drivers/gpu/drm/vc4/vc4_plane.c
-@@ -29,6 +29,14 @@ struct vc4_plane_state {
- u32 *dlist;
- u32 dlist_size; /* Number of dwords in allocated for the display list */
- u32 dlist_count; /* Number of used dwords in the display list. */
-+
-+ /* Offset in the dlist to pointer word 0. */
-+ u32 pw0_offset;
-+
-+ /* Offset where the plane's dlist was last stored in the
-+ hardware at vc4_crtc_atomic_flush() time.
-+ */
-+ u32 *hw_dlist;
- };
-
- static inline struct vc4_plane_state *
-@@ -207,6 +215,8 @@ static int vc4_plane_mode_set(struct drm
- /* Position Word 3: Context. Written by the HVS. */
- vc4_dlist_write(vc4_state, 0xc0c0c0c0);
-
-+ vc4_state->pw0_offset = vc4_state->dlist_count;
-+
- /* Pointer Word 0: RGB / Y Pointer */
- vc4_dlist_write(vc4_state, bo->paddr + offset);
-
-@@ -258,6 +268,8 @@ u32 vc4_plane_write_dlist(struct drm_pla
- struct vc4_plane_state *vc4_state = to_vc4_plane_state(plane->state);
- int i;
-
-+ vc4_state->hw_dlist = dlist;
-+
- /* Can't memcpy_toio() because it needs to be 32-bit writes. */
- for (i = 0; i < vc4_state->dlist_count; i++)
- writel(vc4_state->dlist[i], &dlist[i]);
-@@ -272,6 +284,34 @@ u32 vc4_plane_dlist_size(struct drm_plan
- return vc4_state->dlist_count;
- }
-
-+/* Updates the plane to immediately (well, once the FIFO needs
-+ * refilling) scan out from at a new framebuffer.
-+ */
-+void vc4_plane_async_set_fb(struct drm_plane *plane, struct drm_framebuffer *fb)
-+{
-+ struct vc4_plane_state *vc4_state = to_vc4_plane_state(plane->state);
-+ struct drm_gem_cma_object *bo = drm_fb_cma_get_gem_obj(fb, 0);
-+ uint32_t addr;
-+
-+ /* We're skipping the address adjustment for negative origin,
-+ * because this is only called on the primary plane.
-+ */
-+ WARN_ON_ONCE(plane->state->crtc_x < 0 || plane->state->crtc_y < 0);
-+ addr = bo->paddr + fb->offsets[0];
-+
-+ /* Write the new address into the hardware immediately. The
-+ * scanout will start from this address as soon as the FIFO
-+ * needs to refill with pixels.
-+ */
-+ writel(addr, &vc4_state->hw_dlist[vc4_state->pw0_offset]);
-+
-+ /* Also update the CPU-side dlist copy, so that any later
-+ * atomic updates that don't do a new modeset on our plane
-+ * also use our updated address.
-+ */
-+ vc4_state->dlist[vc4_state->pw0_offset] = addr;
-+}
-+
- static const struct drm_plane_helper_funcs vc4_plane_helper_funcs = {
- .prepare_fb = NULL,
- .cleanup_fb = NULL,
---- /dev/null
-+++ b/drivers/gpu/drm/vc4/vc4_qpu_defines.h
-@@ -0,0 +1,268 @@
-+/*
-+ * Copyright © 2014 Broadcom
-+ *
-+ * Permission is hereby granted, free of charge, to any person obtaining a
-+ * copy of this software and associated documentation files (the "Software"),
-+ * to deal in the Software without restriction, including without limitation
-+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
-+ * and/or sell copies of the Software, and to permit persons to whom the
-+ * Software is furnished to do so, subject to the following conditions:
-+ *
-+ * The above copyright notice and this permission notice (including the next
-+ * paragraph) shall be included in all copies or substantial portions of the
-+ * Software.
-+ *
-+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
-+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
-+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
-+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
-+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
-+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS
-+ * IN THE SOFTWARE.
-+ */
-+
-+#ifndef VC4_QPU_DEFINES_H
-+#define VC4_QPU_DEFINES_H
-+
-+enum qpu_op_add {
-+ QPU_A_NOP,
-+ QPU_A_FADD,
-+ QPU_A_FSUB,
-+ QPU_A_FMIN,
-+ QPU_A_FMAX,
-+ QPU_A_FMINABS,
-+ QPU_A_FMAXABS,
-+ QPU_A_FTOI,
-+ QPU_A_ITOF,
-+ QPU_A_ADD = 12,
-+ QPU_A_SUB,
-+ QPU_A_SHR,
-+ QPU_A_ASR,
-+ QPU_A_ROR,
-+ QPU_A_SHL,
-+ QPU_A_MIN,
-+ QPU_A_MAX,
-+ QPU_A_AND,
-+ QPU_A_OR,
-+ QPU_A_XOR,
-+ QPU_A_NOT,
-+ QPU_A_CLZ,
-+ QPU_A_V8ADDS = 30,
-+ QPU_A_V8SUBS = 31,
-+};
-+
-+enum qpu_op_mul {
-+ QPU_M_NOP,
-+ QPU_M_FMUL,
-+ QPU_M_MUL24,
-+ QPU_M_V8MULD,
-+ QPU_M_V8MIN,
-+ QPU_M_V8MAX,
-+ QPU_M_V8ADDS,
-+ QPU_M_V8SUBS,
-+};
-+
-+enum qpu_raddr {
-+ QPU_R_FRAG_PAYLOAD_ZW = 15, /* W for A file, Z for B file */
-+ /* 0-31 are the plain regfile a or b fields */
-+ QPU_R_UNIF = 32,
-+ QPU_R_VARY = 35,
-+ QPU_R_ELEM_QPU = 38,
-+ QPU_R_NOP,
-+ QPU_R_XY_PIXEL_COORD = 41,
-+ QPU_R_MS_REV_FLAGS = 41,
-+ QPU_R_VPM = 48,
-+ QPU_R_VPM_LD_BUSY,
-+ QPU_R_VPM_LD_WAIT,
-+ QPU_R_MUTEX_ACQUIRE,
-+};
-+
-+enum qpu_waddr {
-+ /* 0-31 are the plain regfile a or b fields */
-+ QPU_W_ACC0 = 32, /* aka r0 */
-+ QPU_W_ACC1,
-+ QPU_W_ACC2,
-+ QPU_W_ACC3,
-+ QPU_W_TMU_NOSWAP,
-+ QPU_W_ACC5,
-+ QPU_W_HOST_INT,
-+ QPU_W_NOP,
-+ QPU_W_UNIFORMS_ADDRESS,
-+ QPU_W_QUAD_XY, /* X for regfile a, Y for regfile b */
-+ QPU_W_MS_FLAGS = 42,
-+ QPU_W_REV_FLAG = 42,
-+ QPU_W_TLB_STENCIL_SETUP = 43,
-+ QPU_W_TLB_Z,
-+ QPU_W_TLB_COLOR_MS,
-+ QPU_W_TLB_COLOR_ALL,
-+ QPU_W_TLB_ALPHA_MASK,
-+ QPU_W_VPM,
-+ QPU_W_VPMVCD_SETUP, /* LD for regfile a, ST for regfile b */
-+ QPU_W_VPM_ADDR, /* LD for regfile a, ST for regfile b */
-+ QPU_W_MUTEX_RELEASE,
-+ QPU_W_SFU_RECIP,
-+ QPU_W_SFU_RECIPSQRT,
-+ QPU_W_SFU_EXP,
-+ QPU_W_SFU_LOG,
-+ QPU_W_TMU0_S,
-+ QPU_W_TMU0_T,
-+ QPU_W_TMU0_R,
-+ QPU_W_TMU0_B,
-+ QPU_W_TMU1_S,
-+ QPU_W_TMU1_T,
-+ QPU_W_TMU1_R,
-+ QPU_W_TMU1_B,
-+};
-+
-+enum qpu_sig_bits {
-+ QPU_SIG_SW_BREAKPOINT,
-+ QPU_SIG_NONE,
-+ QPU_SIG_THREAD_SWITCH,
-+ QPU_SIG_PROG_END,
-+ QPU_SIG_WAIT_FOR_SCOREBOARD,
-+ QPU_SIG_SCOREBOARD_UNLOCK,
-+ QPU_SIG_LAST_THREAD_SWITCH,
-+ QPU_SIG_COVERAGE_LOAD,
-+ QPU_SIG_COLOR_LOAD,
-+ QPU_SIG_COLOR_LOAD_END,
-+ QPU_SIG_LOAD_TMU0,
-+ QPU_SIG_LOAD_TMU1,
-+ QPU_SIG_ALPHA_MASK_LOAD,
-+ QPU_SIG_SMALL_IMM,
-+ QPU_SIG_LOAD_IMM,
-+ QPU_SIG_BRANCH
-+};
-+
-+enum qpu_mux {
-+ /* hardware mux values */
-+ QPU_MUX_R0,
-+ QPU_MUX_R1,
-+ QPU_MUX_R2,
-+ QPU_MUX_R3,
-+ QPU_MUX_R4,
-+ QPU_MUX_R5,
-+ QPU_MUX_A,
-+ QPU_MUX_B,
-+
-+ /* non-hardware mux values */
-+ QPU_MUX_IMM,
-+};
-+
-+enum qpu_cond {
-+ QPU_COND_NEVER,
-+ QPU_COND_ALWAYS,
-+ QPU_COND_ZS,
-+ QPU_COND_ZC,
-+ QPU_COND_NS,
-+ QPU_COND_NC,
-+ QPU_COND_CS,
-+ QPU_COND_CC,
-+};
-+
-+enum qpu_pack_mul {
-+ QPU_PACK_MUL_NOP,
-+ QPU_PACK_MUL_8888 = 3, /* replicated to each 8 bits of the 32-bit dst. */
-+ QPU_PACK_MUL_8A,
-+ QPU_PACK_MUL_8B,
-+ QPU_PACK_MUL_8C,
-+ QPU_PACK_MUL_8D,
-+};
-+
-+enum qpu_pack_a {
-+ QPU_PACK_A_NOP,
-+ /* convert to 16 bit float if float input, or to int16. */
-+ QPU_PACK_A_16A,
-+ QPU_PACK_A_16B,
-+ /* replicated to each 8 bits of the 32-bit dst. */
-+ QPU_PACK_A_8888,
-+ /* Convert to 8-bit unsigned int. */
-+ QPU_PACK_A_8A,
-+ QPU_PACK_A_8B,
-+ QPU_PACK_A_8C,
-+ QPU_PACK_A_8D,
-+
-+ /* Saturating variants of the previous instructions. */
-+ QPU_PACK_A_32_SAT, /* int-only */
-+ QPU_PACK_A_16A_SAT, /* int or float */
-+ QPU_PACK_A_16B_SAT,
-+ QPU_PACK_A_8888_SAT,
-+ QPU_PACK_A_8A_SAT,
-+ QPU_PACK_A_8B_SAT,
-+ QPU_PACK_A_8C_SAT,
-+ QPU_PACK_A_8D_SAT,
-+};
-+
-+enum qpu_unpack_r4 {
-+ QPU_UNPACK_R4_NOP,
-+ QPU_UNPACK_R4_F16A_TO_F32,
-+ QPU_UNPACK_R4_F16B_TO_F32,
-+ QPU_UNPACK_R4_8D_REP,
-+ QPU_UNPACK_R4_8A,
-+ QPU_UNPACK_R4_8B,
-+ QPU_UNPACK_R4_8C,
-+ QPU_UNPACK_R4_8D,
-+};
-+
-+#define QPU_MASK(high, low) ((((uint64_t)1<<((high)-(low)+1))-1)<<(low))
-+/* Using the GNU statement expression extension */
-+#define QPU_SET_FIELD(value, field) \
-+ ({ \
-+ uint64_t fieldval = (uint64_t)(value) << field ## _SHIFT; \
-+ assert((fieldval & ~ field ## _MASK) == 0); \
-+ fieldval & field ## _MASK; \
-+ })
-+
-+#define QPU_GET_FIELD(word, field) ((uint32_t)(((word) & field ## _MASK) >> field ## _SHIFT))
-+
-+#define QPU_SIG_SHIFT 60
-+#define QPU_SIG_MASK QPU_MASK(63, 60)
-+
-+#define QPU_UNPACK_SHIFT 57
-+#define QPU_UNPACK_MASK QPU_MASK(59, 57)
-+
-+/**
-+ * If set, the pack field means PACK_MUL or R4 packing, instead of normal
-+ * regfile a packing.
-+ */
-+#define QPU_PM ((uint64_t)1 << 56)
-+
-+#define QPU_PACK_SHIFT 52
-+#define QPU_PACK_MASK QPU_MASK(55, 52)
-+
-+#define QPU_COND_ADD_SHIFT 49
-+#define QPU_COND_ADD_MASK QPU_MASK(51, 49)
-+#define QPU_COND_MUL_SHIFT 46
-+#define QPU_COND_MUL_MASK QPU_MASK(48, 46)
-+
-+#define QPU_SF ((uint64_t)1 << 45)
-+
-+#define QPU_WADDR_ADD_SHIFT 38
-+#define QPU_WADDR_ADD_MASK QPU_MASK(43, 38)
-+#define QPU_WADDR_MUL_SHIFT 32
-+#define QPU_WADDR_MUL_MASK QPU_MASK(37, 32)
-+
-+#define QPU_OP_MUL_SHIFT 29
-+#define QPU_OP_MUL_MASK QPU_MASK(31, 29)
-+
-+#define QPU_RADDR_A_SHIFT 18
-+#define QPU_RADDR_A_MASK QPU_MASK(23, 18)
-+#define QPU_RADDR_B_SHIFT 12
-+#define QPU_RADDR_B_MASK QPU_MASK(17, 12)
-+#define QPU_SMALL_IMM_SHIFT 12
-+#define QPU_SMALL_IMM_MASK QPU_MASK(17, 12)
-+
-+#define QPU_ADD_A_SHIFT 9
-+#define QPU_ADD_A_MASK QPU_MASK(11, 9)
-+#define QPU_ADD_B_SHIFT 6
-+#define QPU_ADD_B_MASK QPU_MASK(8, 6)
-+#define QPU_MUL_A_SHIFT 3
-+#define QPU_MUL_A_MASK QPU_MASK(5, 3)
-+#define QPU_MUL_B_SHIFT 0
-+#define QPU_MUL_B_MASK QPU_MASK(2, 0)
-+
-+#define QPU_WS ((uint64_t)1 << 44)
-+
-+#define QPU_OP_ADD_SHIFT 24
-+#define QPU_OP_ADD_MASK QPU_MASK(28, 24)
-+
-+#endif /* VC4_QPU_DEFINES_H */
---- /dev/null
-+++ b/drivers/gpu/drm/vc4/vc4_render_cl.c
-@@ -0,0 +1,448 @@
-+/*
-+ * Copyright © 2014-2015 Broadcom
-+ *
-+ * Permission is hereby granted, free of charge, to any person obtaining a
-+ * copy of this software and associated documentation files (the "Software"),
-+ * to deal in the Software without restriction, including without limitation
-+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
-+ * and/or sell copies of the Software, and to permit persons to whom the
-+ * Software is furnished to do so, subject to the following conditions:
-+ *
-+ * The above copyright notice and this permission notice (including the next
-+ * paragraph) shall be included in all copies or substantial portions of the
-+ * Software.
-+ *
-+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
-+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
-+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
-+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
-+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
-+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS
-+ * IN THE SOFTWARE.
-+ */
-+
-+/**
-+ * DOC: Render command list generation
-+ *
-+ * In the VC4 driver, render command list generation is performed by the
-+ * kernel instead of userspace. We do this because validating a
-+ * user-submitted command list is hard to get right and has high CPU overhead,
-+ * while the number of valid configurations for render command lists is
-+ * actually fairly low.
-+ */
-+
-+#include "uapi/drm/vc4_drm.h"
-+#include "vc4_drv.h"
-+#include "vc4_packet.h"
-+
-+struct vc4_rcl_setup {
-+ struct drm_gem_cma_object *color_read;
-+ struct drm_gem_cma_object *color_ms_write;
-+ struct drm_gem_cma_object *zs_read;
-+ struct drm_gem_cma_object *zs_write;
-+
-+ struct drm_gem_cma_object *rcl;
-+ u32 next_offset;
-+};
-+
-+static inline void rcl_u8(struct vc4_rcl_setup *setup, u8 val)
-+{
-+ *(u8 *)(setup->rcl->vaddr + setup->next_offset) = val;
-+ setup->next_offset += 1;
-+}
-+
-+static inline void rcl_u16(struct vc4_rcl_setup *setup, u16 val)
-+{
-+ *(u16 *)(setup->rcl->vaddr + setup->next_offset) = val;
-+ setup->next_offset += 2;
-+}
-+
-+static inline void rcl_u32(struct vc4_rcl_setup *setup, u32 val)
-+{
-+ *(u32 *)(setup->rcl->vaddr + setup->next_offset) = val;
-+ setup->next_offset += 4;
-+}
-+
-+
-+/*
-+ * Emits a no-op STORE_TILE_BUFFER_GENERAL.
-+ *
-+ * If we emit a PACKET_TILE_COORDINATES, it must be followed by a store of
-+ * some sort before another load is triggered.
-+ */
-+static void vc4_store_before_load(struct vc4_rcl_setup *setup)
-+{
-+ rcl_u8(setup, VC4_PACKET_STORE_TILE_BUFFER_GENERAL);
-+ rcl_u16(setup,
-+ VC4_SET_FIELD(VC4_LOADSTORE_TILE_BUFFER_NONE,
-+ VC4_LOADSTORE_TILE_BUFFER_BUFFER) |
-+ VC4_STORE_TILE_BUFFER_DISABLE_COLOR_CLEAR |
-+ VC4_STORE_TILE_BUFFER_DISABLE_ZS_CLEAR |
-+ VC4_STORE_TILE_BUFFER_DISABLE_VG_MASK_CLEAR);
-+ rcl_u32(setup, 0); /* no address, since we're in None mode */
-+}
-+
-+/*
-+ * Emits a PACKET_TILE_COORDINATES if one isn't already pending.
-+ *
-+ * The tile coordinates packet triggers a pending load if there is one, are
-+ * used for clipping during rendering, and determine where loads/stores happen
-+ * relative to their base address.
-+ */
-+static void vc4_tile_coordinates(struct vc4_rcl_setup *setup,
-+ uint32_t x, uint32_t y)
-+{
-+ rcl_u8(setup, VC4_PACKET_TILE_COORDINATES);
-+ rcl_u8(setup, x);
-+ rcl_u8(setup, y);
-+}
-+
-+static void emit_tile(struct vc4_exec_info *exec,
-+ struct vc4_rcl_setup *setup,
-+ uint8_t x, uint8_t y, bool first, bool last)
-+{
-+ struct drm_vc4_submit_cl *args = exec->args;
-+ bool has_bin = args->bin_cl_size != 0;
-+
-+ /* Note that the load doesn't actually occur until the
-+ * tile coords packet is processed, and only one load
-+ * may be outstanding at a time.
-+ */
-+ if (setup->color_read) {
-+ rcl_u8(setup, VC4_PACKET_LOAD_TILE_BUFFER_GENERAL);
-+ rcl_u16(setup, args->color_read.bits);
-+ rcl_u32(setup,
-+ setup->color_read->paddr + args->color_read.offset);
-+ }
-+
-+ if (setup->zs_read) {
-+ if (setup->color_read) {
-+ /* Exec previous load. */
-+ vc4_tile_coordinates(setup, x, y);
-+ vc4_store_before_load(setup);
-+ }
-+
-+ rcl_u8(setup, VC4_PACKET_LOAD_TILE_BUFFER_GENERAL);
-+ rcl_u16(setup, args->zs_read.bits);
-+ rcl_u32(setup, setup->zs_read->paddr + args->zs_read.offset);
-+ }
-+
-+ /* Clipping depends on tile coordinates having been
-+ * emitted, so we always need one here.
-+ */
-+ vc4_tile_coordinates(setup, x, y);
-+
-+ /* Wait for the binner before jumping to the first
-+ * tile's lists.
-+ */
-+ if (first && has_bin)
-+ rcl_u8(setup, VC4_PACKET_WAIT_ON_SEMAPHORE);
-+
-+ if (has_bin) {
-+ rcl_u8(setup, VC4_PACKET_BRANCH_TO_SUB_LIST);
-+ rcl_u32(setup, (exec->tile_bo->paddr +
-+ exec->tile_alloc_offset +
-+ (y * exec->bin_tiles_x + x) * 32));
-+ }
-+
-+ if (setup->zs_write) {
-+ rcl_u8(setup, VC4_PACKET_STORE_TILE_BUFFER_GENERAL);
-+ rcl_u16(setup, args->zs_write.bits |
-+ (setup->color_ms_write ?
-+ VC4_STORE_TILE_BUFFER_DISABLE_COLOR_CLEAR : 0));
-+ rcl_u32(setup,
-+ (setup->zs_write->paddr + args->zs_write.offset) |
-+ ((last && !setup->color_ms_write) ?
-+ VC4_LOADSTORE_TILE_BUFFER_EOF : 0));
-+ }
-+
-+ if (setup->color_ms_write) {
-+ if (setup->zs_write) {
-+ /* Reset after previous store */
-+ vc4_tile_coordinates(setup, x, y);
-+ }
-+
-+ if (last)
-+ rcl_u8(setup, VC4_PACKET_STORE_MS_TILE_BUFFER_AND_EOF);
-+ else
-+ rcl_u8(setup, VC4_PACKET_STORE_MS_TILE_BUFFER);
-+ }
-+}
-+
-+static int vc4_create_rcl_bo(struct drm_device *dev, struct vc4_exec_info *exec,
-+ struct vc4_rcl_setup *setup)
-+{
-+ struct drm_vc4_submit_cl *args = exec->args;
-+ bool has_bin = args->bin_cl_size != 0;
-+ uint8_t min_x_tile = args->min_x_tile;
-+ uint8_t min_y_tile = args->min_y_tile;
-+ uint8_t max_x_tile = args->max_x_tile;
-+ uint8_t max_y_tile = args->max_y_tile;
-+ uint8_t xtiles = max_x_tile - min_x_tile + 1;
-+ uint8_t ytiles = max_y_tile - min_y_tile + 1;
-+ uint8_t x, y;
-+ uint32_t size, loop_body_size;
-+
-+ size = VC4_PACKET_TILE_RENDERING_MODE_CONFIG_SIZE;
-+ loop_body_size = VC4_PACKET_TILE_COORDINATES_SIZE;
-+
-+ if (args->flags & VC4_SUBMIT_CL_USE_CLEAR_COLOR) {
-+ size += VC4_PACKET_CLEAR_COLORS_SIZE +
-+ VC4_PACKET_TILE_COORDINATES_SIZE +
-+ VC4_PACKET_STORE_TILE_BUFFER_GENERAL_SIZE;
-+ }
-+
-+ if (setup->color_read) {
-+ loop_body_size += (VC4_PACKET_LOAD_TILE_BUFFER_GENERAL_SIZE);
-+ }
-+ if (setup->zs_read) {
-+ if (setup->color_read) {
-+ loop_body_size += VC4_PACKET_TILE_COORDINATES_SIZE;
-+ loop_body_size += VC4_PACKET_STORE_TILE_BUFFER_GENERAL_SIZE;
-+ }
-+ loop_body_size += VC4_PACKET_LOAD_TILE_BUFFER_GENERAL_SIZE;
-+ }
-+
-+ if (has_bin) {
-+ size += VC4_PACKET_WAIT_ON_SEMAPHORE_SIZE;
-+ loop_body_size += VC4_PACKET_BRANCH_TO_SUB_LIST_SIZE;
-+ }
-+
-+ if (setup->zs_write)
-+ loop_body_size += VC4_PACKET_STORE_TILE_BUFFER_GENERAL_SIZE;
-+ if (setup->color_ms_write) {
-+ if (setup->zs_write)
-+ loop_body_size += VC4_PACKET_TILE_COORDINATES_SIZE;
-+ loop_body_size += VC4_PACKET_STORE_MS_TILE_BUFFER_SIZE;
-+ }
-+ size += xtiles * ytiles * loop_body_size;
-+
-+ setup->rcl = &vc4_bo_create(dev, size)->base;
-+ if (!setup->rcl)
-+ return -ENOMEM;
-+ list_add_tail(&to_vc4_bo(&setup->rcl->base)->unref_head,
-+ &exec->unref_list);
-+
-+ rcl_u8(setup, VC4_PACKET_TILE_RENDERING_MODE_CONFIG);
-+ rcl_u32(setup,
-+ (setup->color_ms_write ?
-+ (setup->color_ms_write->paddr +
-+ args->color_ms_write.offset) :
-+ 0));
-+ rcl_u16(setup, args->width);
-+ rcl_u16(setup, args->height);
-+ rcl_u16(setup, args->color_ms_write.bits);
-+
-+ /* The tile buffer gets cleared when the previous tile is stored. If
-+ * the clear values changed between frames, then the tile buffer has
-+ * stale clear values in it, so we have to do a store in None mode (no
-+ * writes) so that we trigger the tile buffer clear.
-+ */
-+ if (args->flags & VC4_SUBMIT_CL_USE_CLEAR_COLOR) {
-+ rcl_u8(setup, VC4_PACKET_CLEAR_COLORS);
-+ rcl_u32(setup, args->clear_color[0]);
-+ rcl_u32(setup, args->clear_color[1]);
-+ rcl_u32(setup, args->clear_z);
-+ rcl_u8(setup, args->clear_s);
-+
-+ vc4_tile_coordinates(setup, 0, 0);
-+
-+ rcl_u8(setup, VC4_PACKET_STORE_TILE_BUFFER_GENERAL);
-+ rcl_u16(setup, VC4_LOADSTORE_TILE_BUFFER_NONE);
-+ rcl_u32(setup, 0); /* no address, since we're in None mode */
-+ }
-+
-+ for (y = min_y_tile; y <= max_y_tile; y++) {
-+ for (x = min_x_tile; x <= max_x_tile; x++) {
-+ bool first = (x == min_x_tile && y == min_y_tile);
-+ bool last = (x == max_x_tile && y == max_y_tile);
-+ emit_tile(exec, setup, x, y, first, last);
-+ }
-+ }
-+
-+ BUG_ON(setup->next_offset != size);
-+ exec->ct1ca = setup->rcl->paddr;
-+ exec->ct1ea = setup->rcl->paddr + setup->next_offset;
-+
-+ return 0;
-+}
-+
-+static int vc4_rcl_surface_setup(struct vc4_exec_info *exec,
-+ struct drm_gem_cma_object **obj,
-+ struct drm_vc4_submit_rcl_surface *surf)
-+{
-+ uint8_t tiling = VC4_GET_FIELD(surf->bits,
-+ VC4_LOADSTORE_TILE_BUFFER_TILING);
-+ uint8_t buffer = VC4_GET_FIELD(surf->bits,
-+ VC4_LOADSTORE_TILE_BUFFER_BUFFER);
-+ uint8_t format = VC4_GET_FIELD(surf->bits,
-+ VC4_LOADSTORE_TILE_BUFFER_FORMAT);
-+ int cpp;
-+
-+ if (surf->pad != 0) {
-+ DRM_ERROR("Padding unset\n");
-+ return -EINVAL;
-+ }
-+
-+ if (surf->hindex == ~0)
-+ return 0;
-+
-+ if (!vc4_use_bo(exec, surf->hindex, VC4_MODE_RENDER, obj))
-+ return -EINVAL;
-+
-+ if (surf->bits & ~(VC4_LOADSTORE_TILE_BUFFER_TILING_MASK |
-+ VC4_LOADSTORE_TILE_BUFFER_BUFFER_MASK |
-+ VC4_LOADSTORE_TILE_BUFFER_FORMAT_MASK)) {
-+ DRM_ERROR("Unknown bits in load/store: 0x%04x\n",
-+ surf->bits);
-+ return -EINVAL;
-+ }
-+
-+ if (tiling > VC4_TILING_FORMAT_LT) {
-+ DRM_ERROR("Bad tiling format\n");
-+ return -EINVAL;
-+ }
-+
-+ if (buffer == VC4_LOADSTORE_TILE_BUFFER_ZS) {
-+ if (format != 0) {
-+ DRM_ERROR("No color format should be set for ZS\n");
-+ return -EINVAL;
-+ }
-+ cpp = 4;
-+ } else if (buffer == VC4_LOADSTORE_TILE_BUFFER_COLOR) {
-+ switch (format) {
-+ case VC4_LOADSTORE_TILE_BUFFER_BGR565:
-+ case VC4_LOADSTORE_TILE_BUFFER_BGR565_DITHER:
-+ cpp = 2;
-+ break;
-+ case VC4_LOADSTORE_TILE_BUFFER_RGBA8888:
-+ cpp = 4;
-+ break;
-+ default:
-+ DRM_ERROR("Bad tile buffer format\n");
-+ return -EINVAL;
-+ }
-+ } else {
-+ DRM_ERROR("Bad load/store buffer %d.\n", buffer);
-+ return -EINVAL;
-+ }
-+
-+ if (surf->offset & 0xf) {
-+ DRM_ERROR("load/store buffer must be 16b aligned.\n");
-+ return -EINVAL;
-+ }
-+
-+ if (!vc4_check_tex_size(exec, *obj, surf->offset, tiling,
-+ exec->args->width, exec->args->height, cpp)) {
-+ return -EINVAL;
-+ }
-+
-+ return 0;
-+}
-+
-+static int
-+vc4_rcl_ms_surface_setup(struct vc4_exec_info *exec,
-+ struct drm_gem_cma_object **obj,
-+ struct drm_vc4_submit_rcl_surface *surf)
-+{
-+ uint8_t tiling = VC4_GET_FIELD(surf->bits,
-+ VC4_RENDER_CONFIG_MEMORY_FORMAT);
-+ uint8_t format = VC4_GET_FIELD(surf->bits,
-+ VC4_RENDER_CONFIG_FORMAT);
-+ int cpp;
-+
-+ if (surf->pad != 0) {
-+ DRM_ERROR("Padding unset\n");
-+ return -EINVAL;
-+ }
-+
-+ if (surf->bits & ~(VC4_RENDER_CONFIG_MEMORY_FORMAT_MASK |
-+ VC4_RENDER_CONFIG_FORMAT_MASK)) {
-+ DRM_ERROR("Unknown bits in render config: 0x%04x\n",
-+ surf->bits);
-+ return -EINVAL;
-+ }
-+
-+ if (surf->hindex == ~0)
-+ return 0;
-+
-+ if (!vc4_use_bo(exec, surf->hindex, VC4_MODE_RENDER, obj))
-+ return -EINVAL;
-+
-+ if (tiling > VC4_TILING_FORMAT_LT) {
-+ DRM_ERROR("Bad tiling format\n");
-+ return -EINVAL;
-+ }
-+
-+ switch (format) {
-+ case VC4_RENDER_CONFIG_FORMAT_BGR565_DITHERED:
-+ case VC4_RENDER_CONFIG_FORMAT_BGR565:
-+ cpp = 2;
-+ break;
-+ case VC4_RENDER_CONFIG_FORMAT_RGBA8888:
-+ cpp = 4;
-+ break;
-+ default:
-+ DRM_ERROR("Bad tile buffer format\n");
-+ return -EINVAL;
-+ }
-+
-+ if (!vc4_check_tex_size(exec, *obj, surf->offset, tiling,
-+ exec->args->width, exec->args->height, cpp)) {
-+ return -EINVAL;
-+ }
-+
-+ return 0;
-+}
-+
-+int vc4_get_rcl(struct drm_device *dev, struct vc4_exec_info *exec)
-+{
-+ struct vc4_rcl_setup setup = {0};
-+ struct drm_vc4_submit_cl *args = exec->args;
-+ bool has_bin = args->bin_cl_size != 0;
-+ int ret;
-+
-+ if (args->min_x_tile > args->max_x_tile ||
-+ args->min_y_tile > args->max_y_tile) {
-+ DRM_ERROR("Bad render tile set (%d,%d)-(%d,%d)\n",
-+ args->min_x_tile, args->min_y_tile,
-+ args->max_x_tile, args->max_y_tile);
-+ return -EINVAL;
-+ }
-+
-+ if (has_bin &&
-+ (args->max_x_tile > exec->bin_tiles_x ||
-+ args->max_y_tile > exec->bin_tiles_y)) {
-+ DRM_ERROR("Render tiles (%d,%d) outside of bin config (%d,%d)\n",
-+ args->max_x_tile, args->max_y_tile,
-+ exec->bin_tiles_x, exec->bin_tiles_y);
-+ return -EINVAL;
-+ }
-+
-+ ret = vc4_rcl_surface_setup(exec, &setup.color_read, &args->color_read);
-+ if (ret)
-+ return ret;
-+
-+ ret = vc4_rcl_ms_surface_setup(exec, &setup.color_ms_write,
-+ &args->color_ms_write);
-+ if (ret)
-+ return ret;
-+
-+ ret = vc4_rcl_surface_setup(exec, &setup.zs_read, &args->zs_read);
-+ if (ret)
-+ return ret;
-+
-+ ret = vc4_rcl_surface_setup(exec, &setup.zs_write, &args->zs_write);
-+ if (ret)
-+ return ret;
-+
-+ /* We shouldn't even have the job submitted to us if there's no
-+ * surface to write out.
-+ */
-+ if (!setup.color_ms_write && !setup.zs_write) {
-+ DRM_ERROR("RCL requires color or Z/S write\n");
-+ return -EINVAL;
-+ }
-+
-+ return vc4_create_rcl_bo(dev, exec, &setup);
-+}
---- /dev/null
-+++ b/drivers/gpu/drm/vc4/vc4_trace.h
-@@ -0,0 +1,63 @@
-+/*
-+ * Copyright (C) 2015 Broadcom
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ */
-+
-+#if !defined(_VC4_TRACE_H_) || defined(TRACE_HEADER_MULTI_READ)
-+#define _VC4_TRACE_H_
-+
-+#include <linux/stringify.h>
-+#include <linux/types.h>
-+#include <linux/tracepoint.h>
-+
-+#undef TRACE_SYSTEM
-+#define TRACE_SYSTEM vc4
-+#define TRACE_INCLUDE_FILE vc4_trace
-+
-+TRACE_EVENT(vc4_wait_for_seqno_begin,
-+ TP_PROTO(struct drm_device *dev, uint64_t seqno, uint64_t timeout),
-+ TP_ARGS(dev, seqno, timeout),
-+
-+ TP_STRUCT__entry(
-+ __field(u32, dev)
-+ __field(u64, seqno)
-+ __field(u64, timeout)
-+ ),
-+
-+ TP_fast_assign(
-+ __entry->dev = dev->primary->index;
-+ __entry->seqno = seqno;
-+ __entry->timeout = timeout;
-+ ),
-+
-+ TP_printk("dev=%u, seqno=%llu, timeout=%llu",
-+ __entry->dev, __entry->seqno, __entry->timeout)
-+);
-+
-+TRACE_EVENT(vc4_wait_for_seqno_end,
-+ TP_PROTO(struct drm_device *dev, uint64_t seqno),
-+ TP_ARGS(dev, seqno),
-+
-+ TP_STRUCT__entry(
-+ __field(u32, dev)
-+ __field(u64, seqno)
-+ ),
-+
-+ TP_fast_assign(
-+ __entry->dev = dev->primary->index;
-+ __entry->seqno = seqno;
-+ ),
-+
-+ TP_printk("dev=%u, seqno=%llu",
-+ __entry->dev, __entry->seqno)
-+);
-+
-+#endif /* _VC4_TRACE_H_ */
-+
-+/* This part must be outside protection */
-+#undef TRACE_INCLUDE_PATH
-+#define TRACE_INCLUDE_PATH .
-+#include <trace/define_trace.h>
---- /dev/null
-+++ b/drivers/gpu/drm/vc4/vc4_trace_points.c
-@@ -0,0 +1,14 @@
-+/*
-+ * Copyright (C) 2015 Broadcom
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ */
-+
-+#include "vc4_drv.h"
-+
-+#ifndef __CHECKER__
-+#define CREATE_TRACE_POINTS
-+#include "vc4_trace.h"
-+#endif
---- /dev/null
-+++ b/drivers/gpu/drm/vc4/vc4_v3d.c
-@@ -0,0 +1,268 @@
-+/*
-+ * Copyright (c) 2014 The Linux Foundation. All rights reserved.
-+ * Copyright (C) 2013 Red Hat
-+ * Author: Rob Clark <robdclark at gmail.com>
-+ *
-+ * This program is free software; you can redistribute it and/or modify it
-+ * under the terms of the GNU General Public License version 2 as published by
-+ * the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful, but WITHOUT
-+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
-+ * more details.
-+ *
-+ * You should have received a copy of the GNU General Public License along with
-+ * this program. If not, see <http://www.gnu.org/licenses/>.
-+ */
-+
-+#include "linux/component.h"
-+#include "soc/bcm2835/raspberrypi-firmware.h"
-+#include "vc4_drv.h"
-+#include "vc4_regs.h"
-+
-+#ifdef CONFIG_DEBUG_FS
-+#define REGDEF(reg) { reg, #reg }
-+static const struct {
-+ uint32_t reg;
-+ const char *name;
-+} vc4_reg_defs[] = {
-+ REGDEF(V3D_IDENT0),
-+ REGDEF(V3D_IDENT1),
-+ REGDEF(V3D_IDENT2),
-+ REGDEF(V3D_SCRATCH),
-+ REGDEF(V3D_L2CACTL),
-+ REGDEF(V3D_SLCACTL),
-+ REGDEF(V3D_INTCTL),
-+ REGDEF(V3D_INTENA),
-+ REGDEF(V3D_INTDIS),
-+ REGDEF(V3D_CT0CS),
-+ REGDEF(V3D_CT1CS),
-+ REGDEF(V3D_CT0EA),
-+ REGDEF(V3D_CT1EA),
-+ REGDEF(V3D_CT0CA),
-+ REGDEF(V3D_CT1CA),
-+ REGDEF(V3D_CT00RA0),
-+ REGDEF(V3D_CT01RA0),
-+ REGDEF(V3D_CT0LC),
-+ REGDEF(V3D_CT1LC),
-+ REGDEF(V3D_CT0PC),
-+ REGDEF(V3D_CT1PC),
-+ REGDEF(V3D_PCS),
-+ REGDEF(V3D_BFC),
-+ REGDEF(V3D_RFC),
-+ REGDEF(V3D_BPCA),
-+ REGDEF(V3D_BPCS),
-+ REGDEF(V3D_BPOA),
-+ REGDEF(V3D_BPOS),
-+ REGDEF(V3D_BXCF),
-+ REGDEF(V3D_SQRSV0),
-+ REGDEF(V3D_SQRSV1),
-+ REGDEF(V3D_SQCNTL),
-+ REGDEF(V3D_SRQPC),
-+ REGDEF(V3D_SRQUA),
-+ REGDEF(V3D_SRQUL),
-+ REGDEF(V3D_SRQCS),
-+ REGDEF(V3D_VPACNTL),
-+ REGDEF(V3D_VPMBASE),
-+ REGDEF(V3D_PCTRC),
-+ REGDEF(V3D_PCTRE),
-+ REGDEF(V3D_PCTR0),
-+ REGDEF(V3D_PCTRS0),
-+ REGDEF(V3D_PCTR1),
-+ REGDEF(V3D_PCTRS1),
-+ REGDEF(V3D_PCTR2),
-+ REGDEF(V3D_PCTRS2),
-+ REGDEF(V3D_PCTR3),
-+ REGDEF(V3D_PCTRS3),
-+ REGDEF(V3D_PCTR4),
-+ REGDEF(V3D_PCTRS4),
-+ REGDEF(V3D_PCTR5),
-+ REGDEF(V3D_PCTRS5),
-+ REGDEF(V3D_PCTR6),
-+ REGDEF(V3D_PCTRS6),
-+ REGDEF(V3D_PCTR7),
-+ REGDEF(V3D_PCTRS7),
-+ REGDEF(V3D_PCTR8),
-+ REGDEF(V3D_PCTRS8),
-+ REGDEF(V3D_PCTR9),
-+ REGDEF(V3D_PCTRS9),
-+ REGDEF(V3D_PCTR10),
-+ REGDEF(V3D_PCTRS10),
-+ REGDEF(V3D_PCTR11),
-+ REGDEF(V3D_PCTRS11),
-+ REGDEF(V3D_PCTR12),
-+ REGDEF(V3D_PCTRS12),
-+ REGDEF(V3D_PCTR13),
-+ REGDEF(V3D_PCTRS13),
-+ REGDEF(V3D_PCTR14),
-+ REGDEF(V3D_PCTRS14),
-+ REGDEF(V3D_PCTR15),
-+ REGDEF(V3D_PCTRS15),
-+ REGDEF(V3D_BGE),
-+ REGDEF(V3D_FDBGO),
-+ REGDEF(V3D_FDBGB),
-+ REGDEF(V3D_FDBGR),
-+ REGDEF(V3D_FDBGS),
-+ REGDEF(V3D_ERRSTAT),
-+};
-+
-+int vc4_v3d_debugfs_regs(struct seq_file *m, void *unused)
-+{
-+ struct drm_info_node *node = (struct drm_info_node *) m->private;
-+ struct drm_device *dev = node->minor->dev;
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ int i;
-+
-+ for (i = 0; i < ARRAY_SIZE(vc4_reg_defs); i++) {
-+ seq_printf(m, "%s (0x%04x): 0x%08x\n",
-+ vc4_reg_defs[i].name, vc4_reg_defs[i].reg,
-+ V3D_READ(vc4_reg_defs[i].reg));
-+ }
-+
-+ return 0;
-+}
-+
-+int vc4_v3d_debugfs_ident(struct seq_file *m, void *unused)
-+{
-+ struct drm_info_node *node = (struct drm_info_node *) m->private;
-+ struct drm_device *dev = node->minor->dev;
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ uint32_t ident1 = V3D_READ(V3D_IDENT1);
-+ uint32_t nslc = VC4_GET_FIELD(ident1, V3D_IDENT1_NSLC);
-+ uint32_t tups = VC4_GET_FIELD(ident1, V3D_IDENT1_TUPS);
-+ uint32_t qups = VC4_GET_FIELD(ident1, V3D_IDENT1_QUPS);
-+
-+ seq_printf(m, "Revision: %d\n", VC4_GET_FIELD(ident1, V3D_IDENT1_REV));
-+ seq_printf(m, "Slices: %d\n", nslc);
-+ seq_printf(m, "TMUs: %d\n", nslc * tups);
-+ seq_printf(m, "QPUs: %d\n", nslc * qups);
-+ seq_printf(m, "Semaphores: %d\n", VC4_GET_FIELD(ident1, V3D_IDENT1_NSEM));
-+
-+ return 0;
-+}
-+#endif /* CONFIG_DEBUG_FS */
-+
-+/*
-+ * Asks the firmware to turn on power to the V3D engine.
-+ *
-+ * This may be doable with just the clocks interface, though this
-+ * packet does some other register setup from the firmware, too.
-+ */
-+int
-+vc4_v3d_set_power(struct vc4_dev *vc4, bool on)
-+{
-+ u32 packet = on;
-+
-+ return rpi_firmware_property(vc4->firmware,
-+ RPI_FIRMWARE_SET_ENABLE_QPU,
-+ &packet, sizeof(packet));
-+}
-+
-+static void vc4_v3d_init_hw(struct drm_device *dev)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+
-+ /* Take all the memory that would have been reserved for user
-+ * QPU programs, since we don't have an interface for running
-+ * them, anyway.
-+ */
-+ V3D_WRITE(V3D_VPMBASE, 0);
-+}
-+
-+static int vc4_v3d_bind(struct device *dev, struct device *master, void *data)
-+{
-+ struct platform_device *pdev = to_platform_device(dev);
-+ struct drm_device *drm = dev_get_drvdata(master);
-+ struct vc4_dev *vc4 = to_vc4_dev(drm);
-+ struct vc4_v3d *v3d = NULL;
-+ int ret;
-+
-+ v3d = devm_kzalloc(&pdev->dev, sizeof(*v3d), GFP_KERNEL);
-+ if (!v3d)
-+ return -ENOMEM;
-+
-+ v3d->pdev = pdev;
-+
-+ v3d->regs = vc4_ioremap_regs(pdev, 0);
-+ if (IS_ERR(v3d->regs))
-+ return PTR_ERR(v3d->regs);
-+
-+ vc4->v3d = v3d;
-+
-+ ret = vc4_v3d_set_power(vc4, true);
-+ if (ret)
-+ return ret;
-+
-+ if (V3D_READ(V3D_IDENT0) != V3D_EXPECTED_IDENT0) {
-+ DRM_ERROR("V3D_IDENT0 read 0x%08x instead of 0x%08x\n",
-+ V3D_READ(V3D_IDENT0), V3D_EXPECTED_IDENT0);
-+ return -EINVAL;
-+ }
-+
-+ /* Reset the binner overflow address/size at setup, to be sure
-+ * we don't reuse an old one.
-+ */
-+ V3D_WRITE(V3D_BPOA, 0);
-+ V3D_WRITE(V3D_BPOS, 0);
-+
-+ vc4_v3d_init_hw(drm);
-+
-+ ret = drm_irq_install(drm, platform_get_irq(pdev, 0));
-+ if (ret) {
-+ DRM_ERROR("Failed to install IRQ handler\n");
-+ return ret;
-+ }
-+
-+ return 0;
-+}
-+
-+static void vc4_v3d_unbind(struct device *dev, struct device *master,
-+ void *data)
-+{
-+ struct drm_device *drm = dev_get_drvdata(master);
-+ struct vc4_dev *vc4 = to_vc4_dev(drm);
-+
-+ drm_irq_uninstall(drm);
-+
-+ /* Disable the binner's overflow memory address, so the next
-+ * driver probe (if any) doesn't try to reuse our old
-+ * allocation.
-+ */
-+ V3D_WRITE(V3D_BPOA, 0);
-+ V3D_WRITE(V3D_BPOS, 0);
-+
-+ vc4_v3d_set_power(vc4, false);
-+
-+ vc4->v3d = NULL;
-+}
-+
-+static const struct component_ops vc4_v3d_ops = {
-+ .bind = vc4_v3d_bind,
-+ .unbind = vc4_v3d_unbind,
-+};
-+
-+static int vc4_v3d_dev_probe(struct platform_device *pdev)
-+{
-+ return component_add(&pdev->dev, &vc4_v3d_ops);
-+}
-+
-+static int vc4_v3d_dev_remove(struct platform_device *pdev)
-+{
-+ component_del(&pdev->dev, &vc4_v3d_ops);
-+ return 0;
-+}
-+
-+static const struct of_device_id vc4_v3d_dt_match[] = {
-+ { .compatible = "brcm,vc4-v3d" },
-+ {}
-+};
-+
-+struct platform_driver vc4_v3d_driver = {
-+ .probe = vc4_v3d_dev_probe,
-+ .remove = vc4_v3d_dev_remove,
-+ .driver = {
-+ .name = "vc4_v3d",
-+ .of_match_table = vc4_v3d_dt_match,
-+ },
-+};
---- /dev/null
-+++ b/drivers/gpu/drm/vc4/vc4_validate.c
-@@ -0,0 +1,958 @@
-+/*
-+ * Copyright © 2014 Broadcom
-+ *
-+ * Permission is hereby granted, free of charge, to any person obtaining a
-+ * copy of this software and associated documentation files (the "Software"),
-+ * to deal in the Software without restriction, including without limitation
-+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
-+ * and/or sell copies of the Software, and to permit persons to whom the
-+ * Software is furnished to do so, subject to the following conditions:
-+ *
-+ * The above copyright notice and this permission notice (including the next
-+ * paragraph) shall be included in all copies or substantial portions of the
-+ * Software.
-+ *
-+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
-+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
-+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
-+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
-+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
-+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS
-+ * IN THE SOFTWARE.
-+ */
-+
-+/**
-+ * Command list validator for VC4.
-+ *
-+ * The VC4 has no IOMMU between it and system memory. So, a user with
-+ * access to execute command lists could escalate privilege by
-+ * overwriting system memory (drawing to it as a framebuffer) or
-+ * reading system memory it shouldn't (reading it as a texture, or
-+ * uniform data, or vertex data).
-+ *
-+ * This validates command lists to ensure that all accesses are within
-+ * the bounds of the GEM objects referenced. It explicitly whitelists
-+ * packets, and looks at the offsets in any address fields to make
-+ * sure they're constrained within the BOs they reference.
-+ *
-+ * Note that because of the validation that's happening anyway, this
-+ * is where GEM relocation processing happens.
-+ */
-+
-+#include "uapi/drm/vc4_drm.h"
-+#include "vc4_drv.h"
-+#include "vc4_packet.h"
-+
-+#define VALIDATE_ARGS \
-+ struct vc4_exec_info *exec, \
-+ void *validated, \
-+ void *untrusted
-+
-+
-+/** Return the width in pixels of a 64-byte microtile. */
-+static uint32_t
-+utile_width(int cpp)
-+{
-+ switch (cpp) {
-+ case 1:
-+ case 2:
-+ return 8;
-+ case 4:
-+ return 4;
-+ case 8:
-+ return 2;
-+ default:
-+ DRM_ERROR("unknown cpp: %d\n", cpp);
-+ return 1;
-+ }
-+}
-+
-+/** Return the height in pixels of a 64-byte microtile. */
-+static uint32_t
-+utile_height(int cpp)
-+{
-+ switch (cpp) {
-+ case 1:
-+ return 8;
-+ case 2:
-+ case 4:
-+ case 8:
-+ return 4;
-+ default:
-+ DRM_ERROR("unknown cpp: %d\n", cpp);
-+ return 1;
-+ }
-+}
-+
-+/**
-+ * The texture unit decides what tiling format a particular miplevel is using
-+ * this function, so we lay out our miptrees accordingly.
-+ */
-+static bool
-+size_is_lt(uint32_t width, uint32_t height, int cpp)
-+{
-+ return (width <= 4 * utile_width(cpp) ||
-+ height <= 4 * utile_height(cpp));
-+}
-+
-+bool
-+vc4_use_bo(struct vc4_exec_info *exec,
-+ uint32_t hindex,
-+ enum vc4_bo_mode mode,
-+ struct drm_gem_cma_object **obj)
-+{
-+ *obj = NULL;
-+
-+ if (hindex >= exec->bo_count) {
-+ DRM_ERROR("BO index %d greater than BO count %d\n",
-+ hindex, exec->bo_count);
-+ return false;
-+ }
-+
-+ if (exec->bo[hindex].mode != mode) {
-+ if (exec->bo[hindex].mode == VC4_MODE_UNDECIDED) {
-+ exec->bo[hindex].mode = mode;
-+ } else {
-+ DRM_ERROR("BO index %d reused with mode %d vs %d\n",
-+ hindex, exec->bo[hindex].mode, mode);
-+ return false;
-+ }
-+ }
-+
-+ *obj = exec->bo[hindex].bo;
-+ return true;
-+}
-+
-+static bool
-+vc4_use_handle(struct vc4_exec_info *exec,
-+ uint32_t gem_handles_packet_index,
-+ enum vc4_bo_mode mode,
-+ struct drm_gem_cma_object **obj)
-+{
-+ return vc4_use_bo(exec, exec->bo_index[gem_handles_packet_index],
-+ mode, obj);
-+}
-+
-+static uint32_t
-+gl_shader_rec_size(uint32_t pointer_bits)
-+{
-+ uint32_t attribute_count = pointer_bits & 7;
-+ bool extended = pointer_bits & 8;
-+
-+ if (attribute_count == 0)
-+ attribute_count = 8;
-+
-+ if (extended)
-+ return 100 + attribute_count * 4;
-+ else
-+ return 36 + attribute_count * 8;
-+}
-+
-+bool
-+vc4_check_tex_size(struct vc4_exec_info *exec, struct drm_gem_cma_object *fbo,
-+ uint32_t offset, uint8_t tiling_format,
-+ uint32_t width, uint32_t height, uint8_t cpp)
-+{
-+ uint32_t aligned_width, aligned_height, stride, size;
-+ uint32_t utile_w = utile_width(cpp);
-+ uint32_t utile_h = utile_height(cpp);
-+
-+ /* The shaded vertex format stores signed 12.4 fixed point
-+ * (-2048,2047) offsets from the viewport center, so we should
-+ * never have a render target larger than 4096. The texture
-+ * unit can only sample from 2048x2048, so it's even more
-+ * restricted. This lets us avoid worrying about overflow in
-+ * our math.
-+ */
-+ if (width > 4096 || height > 4096) {
-+ DRM_ERROR("Surface dimesions (%d,%d) too large", width, height);
-+ return false;
-+ }
-+
-+ switch (tiling_format) {
-+ case VC4_TILING_FORMAT_LINEAR:
-+ aligned_width = round_up(width, utile_w);
-+ aligned_height = height;
-+ break;
-+ case VC4_TILING_FORMAT_T:
-+ aligned_width = round_up(width, utile_w * 8);
-+ aligned_height = round_up(height, utile_h * 8);
-+ break;
-+ case VC4_TILING_FORMAT_LT:
-+ aligned_width = round_up(width, utile_w);
-+ aligned_height = round_up(height, utile_h);
-+ break;
-+ default:
-+ DRM_ERROR("buffer tiling %d unsupported\n", tiling_format);
-+ return false;
-+ }
-+
-+ stride = aligned_width * cpp;
-+ size = stride * aligned_height;
-+
-+ if (size + offset < size ||
-+ size + offset > fbo->base.size) {
-+ DRM_ERROR("Overflow in %dx%d (%dx%d) fbo size (%d + %d > %d)\n",
-+ width, height,
-+ aligned_width, aligned_height,
-+ size, offset, fbo->base.size);
-+ return false;
-+ }
-+
-+ return true;
-+}
-+
-+static int
-+validate_flush_all(VALIDATE_ARGS)
-+{
-+ if (exec->found_increment_semaphore_packet) {
-+ DRM_ERROR("VC4_PACKET_FLUSH_ALL after "
-+ "VC4_PACKET_INCREMENT_SEMAPHORE\n");
-+ return -EINVAL;
-+ }
-+
-+ return 0;
-+}
-+
-+static int
-+validate_start_tile_binning(VALIDATE_ARGS)
-+{
-+ if (exec->found_start_tile_binning_packet) {
-+ DRM_ERROR("Duplicate VC4_PACKET_START_TILE_BINNING\n");
-+ return -EINVAL;
-+ }
-+ exec->found_start_tile_binning_packet = true;
-+
-+ if (!exec->found_tile_binning_mode_config_packet) {
-+ DRM_ERROR("missing VC4_PACKET_TILE_BINNING_MODE_CONFIG\n");
-+ return -EINVAL;
-+ }
-+
-+ return 0;
-+}
-+
-+static int
-+validate_increment_semaphore(VALIDATE_ARGS)
-+{
-+ if (exec->found_increment_semaphore_packet) {
-+ DRM_ERROR("Duplicate VC4_PACKET_INCREMENT_SEMAPHORE\n");
-+ return -EINVAL;
-+ }
-+ exec->found_increment_semaphore_packet = true;
-+
-+ /* Once we've found the semaphore increment, there should be one FLUSH
-+ * then the end of the command list. The FLUSH actually triggers the
-+ * increment, so we only need to make sure there
-+ */
-+
-+ return 0;
-+}
-+
-+static int
-+validate_indexed_prim_list(VALIDATE_ARGS)
-+{
-+ struct drm_gem_cma_object *ib;
-+ uint32_t length = *(uint32_t *)(untrusted + 1);
-+ uint32_t offset = *(uint32_t *)(untrusted + 5);
-+ uint32_t max_index = *(uint32_t *)(untrusted + 9);
-+ uint32_t index_size = (*(uint8_t *)(untrusted + 0) >> 4) ? 2 : 1;
-+ struct vc4_shader_state *shader_state;
-+
-+ if (exec->found_increment_semaphore_packet) {
-+ DRM_ERROR("Drawing after VC4_PACKET_INCREMENT_SEMAPHORE\n");
-+ return -EINVAL;
-+ }
-+
-+ /* Check overflow condition */
-+ if (exec->shader_state_count == 0) {
-+ DRM_ERROR("shader state must precede primitives\n");
-+ return -EINVAL;
-+ }
-+ shader_state = &exec->shader_state[exec->shader_state_count - 1];
-+
-+ if (max_index > shader_state->max_index)
-+ shader_state->max_index = max_index;
-+
-+ if (!vc4_use_handle(exec, 0, VC4_MODE_RENDER, &ib))
-+ return -EINVAL;
-+
-+ if (offset > ib->base.size ||
-+ (ib->base.size - offset) / index_size < length) {
-+ DRM_ERROR("IB access overflow (%d + %d*%d > %d)\n",
-+ offset, length, index_size, ib->base.size);
-+ return -EINVAL;
-+ }
-+
-+ *(uint32_t *)(validated + 5) = ib->paddr + offset;
-+
-+ return 0;
-+}
-+
-+static int
-+validate_gl_array_primitive(VALIDATE_ARGS)
-+{
-+ uint32_t length = *(uint32_t *)(untrusted + 1);
-+ uint32_t base_index = *(uint32_t *)(untrusted + 5);
-+ uint32_t max_index;
-+ struct vc4_shader_state *shader_state;
-+
-+ if (exec->found_increment_semaphore_packet) {
-+ DRM_ERROR("Drawing after VC4_PACKET_INCREMENT_SEMAPHORE\n");
-+ return -EINVAL;
-+ }
-+
-+ /* Check overflow condition */
-+ if (exec->shader_state_count == 0) {
-+ DRM_ERROR("shader state must precede primitives\n");
-+ return -EINVAL;
-+ }
-+ shader_state = &exec->shader_state[exec->shader_state_count - 1];
-+
-+ if (length + base_index < length) {
-+ DRM_ERROR("primitive vertex count overflow\n");
-+ return -EINVAL;
-+ }
-+ max_index = length + base_index - 1;
-+
-+ if (max_index > shader_state->max_index)
-+ shader_state->max_index = max_index;
-+
-+ return 0;
-+}
-+
-+static int
-+validate_gl_shader_state(VALIDATE_ARGS)
-+{
-+ uint32_t i = exec->shader_state_count++;
-+
-+ if (i >= exec->shader_state_size) {
-+ DRM_ERROR("More requests for shader states than declared\n");
-+ return -EINVAL;
-+ }
-+
-+ exec->shader_state[i].packet = VC4_PACKET_GL_SHADER_STATE;
-+ exec->shader_state[i].addr = *(uint32_t *)untrusted;
-+ exec->shader_state[i].max_index = 0;
-+
-+ if (exec->shader_state[i].addr & ~0xf) {
-+ DRM_ERROR("high bits set in GL shader rec reference\n");
-+ return -EINVAL;
-+ }
-+
-+ *(uint32_t *)validated = (exec->shader_rec_p +
-+ exec->shader_state[i].addr);
-+
-+ exec->shader_rec_p +=
-+ roundup(gl_shader_rec_size(exec->shader_state[i].addr), 16);
-+
-+ return 0;
-+}
-+
-+static int
-+validate_nv_shader_state(VALIDATE_ARGS)
-+{
-+ uint32_t i = exec->shader_state_count++;
-+
-+ if (i >= exec->shader_state_size) {
-+ DRM_ERROR("More requests for shader states than declared\n");
-+ return -EINVAL;
-+ }
-+
-+ exec->shader_state[i].packet = VC4_PACKET_NV_SHADER_STATE;
-+ exec->shader_state[i].addr = *(uint32_t *)untrusted;
-+
-+ if (exec->shader_state[i].addr & 15) {
-+ DRM_ERROR("NV shader state address 0x%08x misaligned\n",
-+ exec->shader_state[i].addr);
-+ return -EINVAL;
-+ }
-+
-+ *(uint32_t *)validated = (exec->shader_state[i].addr +
-+ exec->shader_rec_p);
-+
-+ return 0;
-+}
-+
-+static int
-+validate_tile_binning_config(VALIDATE_ARGS)
-+{
-+ struct drm_device *dev = exec->exec_bo->base.dev;
-+ uint8_t flags;
-+ uint32_t tile_state_size, tile_alloc_size;
-+ uint32_t tile_count;
-+
-+ if (exec->found_tile_binning_mode_config_packet) {
-+ DRM_ERROR("Duplicate VC4_PACKET_TILE_BINNING_MODE_CONFIG\n");
-+ return -EINVAL;
-+ }
-+ exec->found_tile_binning_mode_config_packet = true;
-+
-+ exec->bin_tiles_x = *(uint8_t *)(untrusted + 12);
-+ exec->bin_tiles_y = *(uint8_t *)(untrusted + 13);
-+ tile_count = exec->bin_tiles_x * exec->bin_tiles_y;
-+ flags = *(uint8_t *)(untrusted + 14);
-+
-+ if (exec->bin_tiles_x == 0 ||
-+ exec->bin_tiles_y == 0) {
-+ DRM_ERROR("Tile binning config of %dx%d too small\n",
-+ exec->bin_tiles_x, exec->bin_tiles_y);
-+ return -EINVAL;
-+ }
-+
-+ if (flags & (VC4_BIN_CONFIG_DB_NON_MS |
-+ VC4_BIN_CONFIG_TILE_BUFFER_64BIT |
-+ VC4_BIN_CONFIG_MS_MODE_4X)) {
-+ DRM_ERROR("unsupported bining config flags 0x%02x\n", flags);
-+ return -EINVAL;
-+ }
-+
-+ /* The tile state data array is 48 bytes per tile, and we put it at
-+ * the start of a BO containing both it and the tile alloc.
-+ */
-+ tile_state_size = 48 * tile_count;
-+
-+ /* Since the tile alloc array will follow us, align. */
-+ exec->tile_alloc_offset = roundup(tile_state_size, 4096);
-+
-+ *(uint8_t *)(validated + 14) =
-+ ((flags & ~(VC4_BIN_CONFIG_ALLOC_INIT_BLOCK_SIZE_MASK |
-+ VC4_BIN_CONFIG_ALLOC_BLOCK_SIZE_MASK)) |
-+ VC4_BIN_CONFIG_AUTO_INIT_TSDA |
-+ VC4_SET_FIELD(VC4_BIN_CONFIG_ALLOC_INIT_BLOCK_SIZE_32,
-+ VC4_BIN_CONFIG_ALLOC_INIT_BLOCK_SIZE) |
-+ VC4_SET_FIELD(VC4_BIN_CONFIG_ALLOC_BLOCK_SIZE_128,
-+ VC4_BIN_CONFIG_ALLOC_BLOCK_SIZE));
-+
-+ /* Initial block size. */
-+ tile_alloc_size = 32 * tile_count;
-+
-+ /*
-+ * The initial allocation gets rounded to the next 256 bytes before
-+ * the hardware starts fulfilling further allocations.
-+ */
-+ tile_alloc_size = roundup(tile_alloc_size, 256);
-+
-+ /* Add space for the extra allocations. This is what gets used first,
-+ * before overflow memory. It must have at least 4096 bytes, but we
-+ * want to avoid overflow memory usage if possible.
-+ */
-+ tile_alloc_size += 1024 * 1024;
-+
-+ exec->tile_bo = &vc4_bo_create(dev, exec->tile_alloc_offset +
-+ tile_alloc_size)->base;
-+ if (!exec->tile_bo)
-+ return -ENOMEM;
-+ list_add_tail(&to_vc4_bo(&exec->tile_bo->base)->unref_head,
-+ &exec->unref_list);
-+
-+ /* tile alloc address. */
-+ *(uint32_t *)(validated + 0) = (exec->tile_bo->paddr +
-+ exec->tile_alloc_offset);
-+ /* tile alloc size. */
-+ *(uint32_t *)(validated + 4) = tile_alloc_size;
-+ /* tile state address. */
-+ *(uint32_t *)(validated + 8) = exec->tile_bo->paddr;
-+
-+ return 0;
-+}
-+
-+static int
-+validate_gem_handles(VALIDATE_ARGS)
-+{
-+ memcpy(exec->bo_index, untrusted, sizeof(exec->bo_index));
-+ return 0;
-+}
-+
-+#define VC4_DEFINE_PACKET(packet, name, func) \
-+ [packet] = { packet ## _SIZE, name, func }
-+
-+static const struct cmd_info {
-+ uint16_t len;
-+ const char *name;
-+ int (*func)(struct vc4_exec_info *exec, void *validated,
-+ void *untrusted);
-+} cmd_info[] = {
-+ VC4_DEFINE_PACKET(VC4_PACKET_HALT, "halt", NULL),
-+ VC4_DEFINE_PACKET(VC4_PACKET_NOP, "nop", NULL),
-+ VC4_DEFINE_PACKET(VC4_PACKET_FLUSH, "flush", NULL),
-+ VC4_DEFINE_PACKET(VC4_PACKET_FLUSH_ALL, "flush all state", validate_flush_all),
-+ VC4_DEFINE_PACKET(VC4_PACKET_START_TILE_BINNING, "start tile binning", validate_start_tile_binning),
-+ VC4_DEFINE_PACKET(VC4_PACKET_INCREMENT_SEMAPHORE, "increment semaphore", validate_increment_semaphore),
-+
-+ VC4_DEFINE_PACKET(VC4_PACKET_GL_INDEXED_PRIMITIVE, "Indexed Primitive List", validate_indexed_prim_list),
-+
-+ VC4_DEFINE_PACKET(VC4_PACKET_GL_ARRAY_PRIMITIVE, "Vertex Array Primitives", validate_gl_array_primitive),
-+
-+ /* This is only used by clipped primitives (packets 48 and 49), which
-+ * we don't support parsing yet.
-+ */
-+ VC4_DEFINE_PACKET(VC4_PACKET_PRIMITIVE_LIST_FORMAT, "primitive list format", NULL),
-+
-+ VC4_DEFINE_PACKET(VC4_PACKET_GL_SHADER_STATE, "GL Shader State", validate_gl_shader_state),
-+ VC4_DEFINE_PACKET(VC4_PACKET_NV_SHADER_STATE, "NV Shader State", validate_nv_shader_state),
-+
-+ VC4_DEFINE_PACKET(VC4_PACKET_CONFIGURATION_BITS, "configuration bits", NULL),
-+ VC4_DEFINE_PACKET(VC4_PACKET_FLAT_SHADE_FLAGS, "flat shade flags", NULL),
-+ VC4_DEFINE_PACKET(VC4_PACKET_POINT_SIZE, "point size", NULL),
-+ VC4_DEFINE_PACKET(VC4_PACKET_LINE_WIDTH, "line width", NULL),
-+ VC4_DEFINE_PACKET(VC4_PACKET_RHT_X_BOUNDARY, "RHT X boundary", NULL),
-+ VC4_DEFINE_PACKET(VC4_PACKET_DEPTH_OFFSET, "Depth Offset", NULL),
-+ VC4_DEFINE_PACKET(VC4_PACKET_CLIP_WINDOW, "Clip Window", NULL),
-+ VC4_DEFINE_PACKET(VC4_PACKET_VIEWPORT_OFFSET, "Viewport Offset", NULL),
-+ VC4_DEFINE_PACKET(VC4_PACKET_CLIPPER_XY_SCALING, "Clipper XY Scaling", NULL),
-+ /* Note: The docs say this was also 105, but it was 106 in the
-+ * initial userland code drop.
-+ */
-+ VC4_DEFINE_PACKET(VC4_PACKET_CLIPPER_Z_SCALING, "Clipper Z Scale and Offset", NULL),
-+
-+ VC4_DEFINE_PACKET(VC4_PACKET_TILE_BINNING_MODE_CONFIG, "tile binning configuration", validate_tile_binning_config),
-+
-+ VC4_DEFINE_PACKET(VC4_PACKET_GEM_HANDLES, "GEM handles", validate_gem_handles),
-+};
-+
-+int
-+vc4_validate_bin_cl(struct drm_device *dev,
-+ void *validated,
-+ void *unvalidated,
-+ struct vc4_exec_info *exec)
-+{
-+ uint32_t len = exec->args->bin_cl_size;
-+ uint32_t dst_offset = 0;
-+ uint32_t src_offset = 0;
-+
-+ while (src_offset < len) {
-+ void *dst_pkt = validated + dst_offset;
-+ void *src_pkt = unvalidated + src_offset;
-+ u8 cmd = *(uint8_t *)src_pkt;
-+ const struct cmd_info *info;
-+
-+ if (cmd > ARRAY_SIZE(cmd_info)) {
-+ DRM_ERROR("0x%08x: packet %d out of bounds\n",
-+ src_offset, cmd);
-+ return -EINVAL;
-+ }
-+
-+ info = &cmd_info[cmd];
-+ if (!info->name) {
-+ DRM_ERROR("0x%08x: packet %d invalid\n",
-+ src_offset, cmd);
-+ return -EINVAL;
-+ }
-+
-+#if 0
-+ DRM_INFO("0x%08x: packet %d (%s) size %d processing...\n",
-+ src_offset, cmd, info->name, info->len);
-+#endif
-+
-+ if (src_offset + info->len > len) {
-+ DRM_ERROR("0x%08x: packet %d (%s) length 0x%08x "
-+ "exceeds bounds (0x%08x)\n",
-+ src_offset, cmd, info->name, info->len,
-+ src_offset + len);
-+ return -EINVAL;
-+ }
-+
-+ if (cmd != VC4_PACKET_GEM_HANDLES)
-+ memcpy(dst_pkt, src_pkt, info->len);
-+
-+ if (info->func && info->func(exec,
-+ dst_pkt + 1,
-+ src_pkt + 1)) {
-+ DRM_ERROR("0x%08x: packet %d (%s) failed to "
-+ "validate\n",
-+ src_offset, cmd, info->name);
-+ return -EINVAL;
-+ }
-+
-+ src_offset += info->len;
-+ /* GEM handle loading doesn't produce HW packets. */
-+ if (cmd != VC4_PACKET_GEM_HANDLES)
-+ dst_offset += info->len;
-+
-+ /* When the CL hits halt, it'll stop reading anything else. */
-+ if (cmd == VC4_PACKET_HALT)
-+ break;
-+ }
-+
-+ exec->ct0ea = exec->ct0ca + dst_offset;
-+
-+ if (!exec->found_start_tile_binning_packet) {
-+ DRM_ERROR("Bin CL missing VC4_PACKET_START_TILE_BINNING\n");
-+ return -EINVAL;
-+ }
-+
-+ if (!exec->found_increment_semaphore_packet) {
-+ DRM_ERROR("Bin CL missing VC4_PACKET_INCREMENT_SEMAPHORE\n");
-+ return -EINVAL;
-+ }
-+
-+ return 0;
-+}
-+
-+static bool
-+reloc_tex(struct vc4_exec_info *exec,
-+ void *uniform_data_u,
-+ struct vc4_texture_sample_info *sample,
-+ uint32_t texture_handle_index)
-+
-+{
-+ struct drm_gem_cma_object *tex;
-+ uint32_t p0 = *(uint32_t *)(uniform_data_u + sample->p_offset[0]);
-+ uint32_t p1 = *(uint32_t *)(uniform_data_u + sample->p_offset[1]);
-+ uint32_t p2 = (sample->p_offset[2] != ~0 ?
-+ *(uint32_t *)(uniform_data_u + sample->p_offset[2]) : 0);
-+ uint32_t p3 = (sample->p_offset[3] != ~0 ?
-+ *(uint32_t *)(uniform_data_u + sample->p_offset[3]) : 0);
-+ uint32_t *validated_p0 = exec->uniforms_v + sample->p_offset[0];
-+ uint32_t offset = p0 & VC4_TEX_P0_OFFSET_MASK;
-+ uint32_t miplevels = VC4_GET_FIELD(p0, VC4_TEX_P0_MIPLVLS);
-+ uint32_t width = VC4_GET_FIELD(p1, VC4_TEX_P1_WIDTH);
-+ uint32_t height = VC4_GET_FIELD(p1, VC4_TEX_P1_HEIGHT);
-+ uint32_t cpp, tiling_format, utile_w, utile_h;
-+ uint32_t i;
-+ uint32_t cube_map_stride = 0;
-+ enum vc4_texture_data_type type;
-+
-+ if (!vc4_use_bo(exec, texture_handle_index, VC4_MODE_RENDER, &tex))
-+ return false;
-+
-+ if (sample->is_direct) {
-+ uint32_t remaining_size = tex->base.size - p0;
-+ if (p0 > tex->base.size - 4) {
-+ DRM_ERROR("UBO offset greater than UBO size\n");
-+ goto fail;
-+ }
-+ if (p1 > remaining_size - 4) {
-+ DRM_ERROR("UBO clamp would allow reads outside of UBO\n");
-+ goto fail;
-+ }
-+ *validated_p0 = tex->paddr + p0;
-+ return true;
-+ }
-+
-+ if (width == 0)
-+ width = 2048;
-+ if (height == 0)
-+ height = 2048;
-+
-+ if (p0 & VC4_TEX_P0_CMMODE_MASK) {
-+ if (VC4_GET_FIELD(p2, VC4_TEX_P2_PTYPE) ==
-+ VC4_TEX_P2_PTYPE_CUBE_MAP_STRIDE)
-+ cube_map_stride = p2 & VC4_TEX_P2_CMST_MASK;
-+ if (VC4_GET_FIELD(p3, VC4_TEX_P2_PTYPE) ==
-+ VC4_TEX_P2_PTYPE_CUBE_MAP_STRIDE) {
-+ if (cube_map_stride) {
-+ DRM_ERROR("Cube map stride set twice\n");
-+ goto fail;
-+ }
-+
-+ cube_map_stride = p3 & VC4_TEX_P2_CMST_MASK;
-+ }
-+ if (!cube_map_stride) {
-+ DRM_ERROR("Cube map stride not set\n");
-+ goto fail;
-+ }
-+ }
-+
-+ type = (VC4_GET_FIELD(p0, VC4_TEX_P0_TYPE) |
-+ (VC4_GET_FIELD(p1, VC4_TEX_P1_TYPE4) << 4));
-+
-+ switch (type) {
-+ case VC4_TEXTURE_TYPE_RGBA8888:
-+ case VC4_TEXTURE_TYPE_RGBX8888:
-+ case VC4_TEXTURE_TYPE_RGBA32R:
-+ cpp = 4;
-+ break;
-+ case VC4_TEXTURE_TYPE_RGBA4444:
-+ case VC4_TEXTURE_TYPE_RGBA5551:
-+ case VC4_TEXTURE_TYPE_RGB565:
-+ case VC4_TEXTURE_TYPE_LUMALPHA:
-+ case VC4_TEXTURE_TYPE_S16F:
-+ case VC4_TEXTURE_TYPE_S16:
-+ cpp = 2;
-+ break;
-+ case VC4_TEXTURE_TYPE_LUMINANCE:
-+ case VC4_TEXTURE_TYPE_ALPHA:
-+ case VC4_TEXTURE_TYPE_S8:
-+ cpp = 1;
-+ break;
-+ case VC4_TEXTURE_TYPE_ETC1:
-+ case VC4_TEXTURE_TYPE_BW1:
-+ case VC4_TEXTURE_TYPE_A4:
-+ case VC4_TEXTURE_TYPE_A1:
-+ case VC4_TEXTURE_TYPE_RGBA64:
-+ case VC4_TEXTURE_TYPE_YUV422R:
-+ default:
-+ DRM_ERROR("Texture format %d unsupported\n", type);
-+ goto fail;
-+ }
-+ utile_w = utile_width(cpp);
-+ utile_h = utile_height(cpp);
-+
-+ if (type == VC4_TEXTURE_TYPE_RGBA32R) {
-+ tiling_format = VC4_TILING_FORMAT_LINEAR;
-+ } else {
-+ if (size_is_lt(width, height, cpp))
-+ tiling_format = VC4_TILING_FORMAT_LT;
-+ else
-+ tiling_format = VC4_TILING_FORMAT_T;
-+ }
-+
-+ if (!vc4_check_tex_size(exec, tex, offset + cube_map_stride * 5,
-+ tiling_format, width, height, cpp)) {
-+ goto fail;
-+ }
-+
-+ /* The mipmap levels are stored before the base of the texture. Make
-+ * sure there is actually space in the BO.
-+ */
-+ for (i = 1; i <= miplevels; i++) {
-+ uint32_t level_width = max(width >> i, 1u);
-+ uint32_t level_height = max(height >> i, 1u);
-+ uint32_t aligned_width, aligned_height;
-+ uint32_t level_size;
-+
-+ /* Once the levels get small enough, they drop from T to LT. */
-+ if (tiling_format == VC4_TILING_FORMAT_T &&
-+ size_is_lt(level_width, level_height, cpp)) {
-+ tiling_format = VC4_TILING_FORMAT_LT;
-+ }
-+
-+ switch (tiling_format) {
-+ case VC4_TILING_FORMAT_T:
-+ aligned_width = round_up(level_width, utile_w * 8);
-+ aligned_height = round_up(level_height, utile_h * 8);
-+ break;
-+ case VC4_TILING_FORMAT_LT:
-+ aligned_width = round_up(level_width, utile_w);
-+ aligned_height = round_up(level_height, utile_h);
-+ break;
-+ default:
-+ aligned_width = round_up(level_width, utile_w);
-+ aligned_height = level_height;
-+ break;
-+ }
-+
-+ level_size = aligned_width * cpp * aligned_height;
-+
-+ if (offset < level_size) {
-+ DRM_ERROR("Level %d (%dx%d -> %dx%d) size %db "
-+ "overflowed buffer bounds (offset %d)\n",
-+ i, level_width, level_height,
-+ aligned_width, aligned_height,
-+ level_size, offset);
-+ goto fail;
-+ }
-+
-+ offset -= level_size;
-+ }
-+
-+ *validated_p0 = tex->paddr + p0;
-+
-+ return true;
-+ fail:
-+ DRM_INFO("Texture p0 at %d: 0x%08x\n", sample->p_offset[0], p0);
-+ DRM_INFO("Texture p1 at %d: 0x%08x\n", sample->p_offset[1], p1);
-+ DRM_INFO("Texture p2 at %d: 0x%08x\n", sample->p_offset[2], p2);
-+ DRM_INFO("Texture p3 at %d: 0x%08x\n", sample->p_offset[3], p3);
-+ return false;
-+}
-+
-+static int
-+validate_shader_rec(struct drm_device *dev,
-+ struct vc4_exec_info *exec,
-+ struct vc4_shader_state *state)
-+{
-+ uint32_t *src_handles;
-+ void *pkt_u, *pkt_v;
-+ enum shader_rec_reloc_type {
-+ RELOC_CODE,
-+ RELOC_VBO,
-+ };
-+ struct shader_rec_reloc {
-+ enum shader_rec_reloc_type type;
-+ uint32_t offset;
-+ };
-+ static const struct shader_rec_reloc gl_relocs[] = {
-+ { RELOC_CODE, 4 }, /* fs */
-+ { RELOC_CODE, 16 }, /* vs */
-+ { RELOC_CODE, 28 }, /* cs */
-+ };
-+ static const struct shader_rec_reloc nv_relocs[] = {
-+ { RELOC_CODE, 4 }, /* fs */
-+ { RELOC_VBO, 12 }
-+ };
-+ const struct shader_rec_reloc *relocs;
-+ struct drm_gem_cma_object *bo[ARRAY_SIZE(gl_relocs) + 8];
-+ uint32_t nr_attributes = 0, nr_fixed_relocs, nr_relocs, packet_size;
-+ int i;
-+ struct vc4_validated_shader_info *validated_shader;
-+
-+ if (state->packet == VC4_PACKET_NV_SHADER_STATE) {
-+ relocs = nv_relocs;
-+ nr_fixed_relocs = ARRAY_SIZE(nv_relocs);
-+
-+ packet_size = 16;
-+ } else {
-+ relocs = gl_relocs;
-+ nr_fixed_relocs = ARRAY_SIZE(gl_relocs);
-+
-+ nr_attributes = state->addr & 0x7;
-+ if (nr_attributes == 0)
-+ nr_attributes = 8;
-+ packet_size = gl_shader_rec_size(state->addr);
-+ }
-+ nr_relocs = nr_fixed_relocs + nr_attributes;
-+
-+ if (nr_relocs * 4 > exec->shader_rec_size) {
-+ DRM_ERROR("overflowed shader recs reading %d handles "
-+ "from %d bytes left\n",
-+ nr_relocs, exec->shader_rec_size);
-+ return -EINVAL;
-+ }
-+ src_handles = exec->shader_rec_u;
-+ exec->shader_rec_u += nr_relocs * 4;
-+ exec->shader_rec_size -= nr_relocs * 4;
-+
-+ if (packet_size > exec->shader_rec_size) {
-+ DRM_ERROR("overflowed shader recs copying %db packet "
-+ "from %d bytes left\n",
-+ packet_size, exec->shader_rec_size);
-+ return -EINVAL;
-+ }
-+ pkt_u = exec->shader_rec_u;
-+ pkt_v = exec->shader_rec_v;
-+ memcpy(pkt_v, pkt_u, packet_size);
-+ exec->shader_rec_u += packet_size;
-+ /* Shader recs have to be aligned to 16 bytes (due to the attribute
-+ * flags being in the low bytes), so round the next validated shader
-+ * rec address up. This should be safe, since we've got so many
-+ * relocations in a shader rec packet.
-+ */
-+ BUG_ON(roundup(packet_size, 16) - packet_size > nr_relocs * 4);
-+ exec->shader_rec_v += roundup(packet_size, 16);
-+ exec->shader_rec_size -= packet_size;
-+
-+ for (i = 0; i < nr_relocs; i++) {
-+ enum vc4_bo_mode mode;
-+
-+ if (i < nr_fixed_relocs && relocs[i].type == RELOC_CODE)
-+ mode = VC4_MODE_SHADER;
-+ else
-+ mode = VC4_MODE_RENDER;
-+
-+ if (!vc4_use_bo(exec, src_handles[i], mode, &bo[i])) {
-+ return false;
-+ }
-+ }
-+
-+ for (i = 0; i < nr_fixed_relocs; i++) {
-+ uint32_t o = relocs[i].offset;
-+ uint32_t src_offset = *(uint32_t *)(pkt_u + o);
-+ uint32_t *texture_handles_u;
-+ void *uniform_data_u;
-+ uint32_t tex;
-+
-+ *(uint32_t *)(pkt_v + o) = bo[i]->paddr + src_offset;
-+
-+ switch (relocs[i].type) {
-+ case RELOC_CODE:
-+ if (src_offset != 0) {
-+ DRM_ERROR("Shaders must be at offset 0 of "
-+ "the BO.\n");
-+ goto fail;
-+ }
-+
-+ validated_shader = to_vc4_bo(&bo[i]->base)->validated_shader;
-+ if (!validated_shader)
-+ goto fail;
-+
-+ if (validated_shader->uniforms_src_size >
-+ exec->uniforms_size) {
-+ DRM_ERROR("Uniforms src buffer overflow\n");
-+ goto fail;
-+ }
-+
-+ texture_handles_u = exec->uniforms_u;
-+ uniform_data_u = (texture_handles_u +
-+ validated_shader->num_texture_samples);
-+
-+ memcpy(exec->uniforms_v, uniform_data_u,
-+ validated_shader->uniforms_size);
-+
-+ for (tex = 0;
-+ tex < validated_shader->num_texture_samples;
-+ tex++) {
-+ if (!reloc_tex(exec,
-+ uniform_data_u,
-+ &validated_shader->texture_samples[tex],
-+ texture_handles_u[tex])) {
-+ goto fail;
-+ }
-+ }
-+
-+ *(uint32_t *)(pkt_v + o + 4) = exec->uniforms_p;
-+
-+ exec->uniforms_u += validated_shader->uniforms_src_size;
-+ exec->uniforms_v += validated_shader->uniforms_size;
-+ exec->uniforms_p += validated_shader->uniforms_size;
-+
-+ break;
-+
-+ case RELOC_VBO:
-+ break;
-+ }
-+ }
-+
-+ for (i = 0; i < nr_attributes; i++) {
-+ struct drm_gem_cma_object *vbo = bo[nr_fixed_relocs + i];
-+ uint32_t o = 36 + i * 8;
-+ uint32_t offset = *(uint32_t *)(pkt_u + o + 0);
-+ uint32_t attr_size = *(uint8_t *)(pkt_u + o + 4) + 1;
-+ uint32_t stride = *(uint8_t *)(pkt_u + o + 5);
-+ uint32_t max_index;
-+
-+ if (state->addr & 0x8)
-+ stride |= (*(uint32_t *)(pkt_u + 100 + i * 4)) & ~0xff;
-+
-+ if (vbo->base.size < offset ||
-+ vbo->base.size - offset < attr_size) {
-+ DRM_ERROR("BO offset overflow (%d + %d > %d)\n",
-+ offset, attr_size, vbo->base.size);
-+ return -EINVAL;
-+ }
-+
-+ if (stride != 0) {
-+ max_index = ((vbo->base.size - offset - attr_size) /
-+ stride);
-+ if (state->max_index > max_index) {
-+ DRM_ERROR("primitives use index %d out of supplied %d\n",
-+ state->max_index, max_index);
-+ return -EINVAL;
-+ }
-+ }
-+
-+ *(uint32_t *)(pkt_v + o) = vbo->paddr + offset;
-+ }
-+
-+ return 0;
-+
-+fail:
-+ return -EINVAL;
-+}
-+
-+int
-+vc4_validate_shader_recs(struct drm_device *dev,
-+ struct vc4_exec_info *exec)
-+{
-+ uint32_t i;
-+ int ret = 0;
-+
-+ for (i = 0; i < exec->shader_state_count; i++) {
-+ ret = validate_shader_rec(dev, exec, &exec->shader_state[i]);
-+ if (ret)
-+ return ret;
-+ }
-+
-+ return ret;
-+}
---- /dev/null
-+++ b/drivers/gpu/drm/vc4/vc4_validate_shaders.c
-@@ -0,0 +1,521 @@
-+/*
-+ * Copyright © 2014 Broadcom
-+ *
-+ * Permission is hereby granted, free of charge, to any person obtaining a
-+ * copy of this software and associated documentation files (the "Software"),
-+ * to deal in the Software without restriction, including without limitation
-+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
-+ * and/or sell copies of the Software, and to permit persons to whom the
-+ * Software is furnished to do so, subject to the following conditions:
-+ *
-+ * The above copyright notice and this permission notice (including the next
-+ * paragraph) shall be included in all copies or substantial portions of the
-+ * Software.
-+ *
-+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
-+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
-+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
-+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
-+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
-+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS
-+ * IN THE SOFTWARE.
-+ */
-+
-+/**
-+ * DOC: Shader validator for VC4.
-+ *
-+ * The VC4 has no IOMMU between it and system memory. So, a user with access
-+ * to execute shaders could escalate privilege by overwriting system memory
-+ * (using the VPM write address register in the general-purpose DMA mode) or
-+ * reading system memory it shouldn't (reading it as a texture, or uniform
-+ * data, or vertex data).
-+ *
-+ * This walks over a shader starting from some offset within a BO, ensuring
-+ * that its accesses are appropriately bounded, and recording how many texture
-+ * accesses are made and where so that we can do relocations for them in the
-+ * uniform stream.
-+ *
-+ * The kernel API has shaders stored in user-mapped BOs. The BOs will be
-+ * forcibly unmapped from the process before validation, and any cache of
-+ * validated state will be flushed if the mapping is faulted back in.
-+ *
-+ * Storing the shaders in BOs means that the validation process will be slow
-+ * due to uncached reads, but since shaders are long-lived and shader BOs are
-+ * never actually modified, this shouldn't be a problem.
-+ */
-+
-+#include "vc4_drv.h"
-+#include "vc4_qpu_defines.h"
-+
-+struct vc4_shader_validation_state {
-+ struct vc4_texture_sample_info tmu_setup[2];
-+ int tmu_write_count[2];
-+
-+ /* For registers that were last written to by a MIN instruction with
-+ * one argument being a uniform, the address of the uniform.
-+ * Otherwise, ~0.
-+ *
-+ * This is used for the validation of direct address memory reads.
-+ */
-+ uint32_t live_min_clamp_offsets[32 + 32 + 4];
-+ bool live_max_clamp_regs[32 + 32 + 4];
-+};
-+
-+static uint32_t
-+waddr_to_live_reg_index(uint32_t waddr, bool is_b)
-+{
-+ if (waddr < 32) {
-+ if (is_b)
-+ return 32 + waddr;
-+ else
-+ return waddr;
-+ } else if (waddr <= QPU_W_ACC3) {
-+
-+ return 64 + waddr - QPU_W_ACC0;
-+ } else {
-+ return ~0;
-+ }
-+}
-+
-+static uint32_t
-+raddr_add_a_to_live_reg_index(uint64_t inst)
-+{
-+ uint32_t sig = QPU_GET_FIELD(inst, QPU_SIG);
-+ uint32_t add_a = QPU_GET_FIELD(inst, QPU_ADD_A);
-+ uint32_t raddr_a = QPU_GET_FIELD(inst, QPU_RADDR_A);
-+ uint32_t raddr_b = QPU_GET_FIELD(inst, QPU_RADDR_B);
-+
-+ if (add_a == QPU_MUX_A) {
-+ return raddr_a;
-+ } else if (add_a == QPU_MUX_B && sig != QPU_SIG_SMALL_IMM) {
-+ return 32 + raddr_b;
-+ } else if (add_a <= QPU_MUX_R3) {
-+ return 64 + add_a;
-+ } else {
-+ return ~0;
-+ }
-+}
-+
-+static bool
-+is_tmu_submit(uint32_t waddr)
-+{
-+ return (waddr == QPU_W_TMU0_S ||
-+ waddr == QPU_W_TMU1_S);
-+}
-+
-+static bool
-+is_tmu_write(uint32_t waddr)
-+{
-+ return (waddr >= QPU_W_TMU0_S &&
-+ waddr <= QPU_W_TMU1_B);
-+}
-+
-+static bool
-+record_validated_texture_sample(struct vc4_validated_shader_info *validated_shader,
-+ struct vc4_shader_validation_state *validation_state,
-+ int tmu)
-+{
-+ uint32_t s = validated_shader->num_texture_samples;
-+ int i;
-+ struct vc4_texture_sample_info *temp_samples;
-+
-+ temp_samples = krealloc(validated_shader->texture_samples,
-+ (s + 1) * sizeof(*temp_samples),
-+ GFP_KERNEL);
-+ if (!temp_samples)
-+ return false;
-+
-+ memcpy(&temp_samples[s],
-+ &validation_state->tmu_setup[tmu],
-+ sizeof(*temp_samples));
-+
-+ validated_shader->num_texture_samples = s + 1;
-+ validated_shader->texture_samples = temp_samples;
-+
-+ for (i = 0; i < 4; i++)
-+ validation_state->tmu_setup[tmu].p_offset[i] = ~0;
-+
-+ return true;
-+}
-+
-+static bool
-+check_tmu_write(uint64_t inst,
-+ struct vc4_validated_shader_info *validated_shader,
-+ struct vc4_shader_validation_state *validation_state,
-+ bool is_mul)
-+{
-+ uint32_t waddr = (is_mul ?
-+ QPU_GET_FIELD(inst, QPU_WADDR_MUL) :
-+ QPU_GET_FIELD(inst, QPU_WADDR_ADD));
-+ uint32_t raddr_a = QPU_GET_FIELD(inst, QPU_RADDR_A);
-+ uint32_t raddr_b = QPU_GET_FIELD(inst, QPU_RADDR_B);
-+ int tmu = waddr > QPU_W_TMU0_B;
-+ bool submit = is_tmu_submit(waddr);
-+ bool is_direct = submit && validation_state->tmu_write_count[tmu] == 0;
-+ uint32_t sig = QPU_GET_FIELD(inst, QPU_SIG);
-+
-+ if (is_direct) {
-+ uint32_t add_b = QPU_GET_FIELD(inst, QPU_ADD_B);
-+ uint32_t clamp_reg, clamp_offset;
-+
-+ if (sig == QPU_SIG_SMALL_IMM) {
-+ DRM_ERROR("direct TMU read used small immediate\n");
-+ return false;
-+ }
-+
-+ /* Make sure that this texture load is an add of the base
-+ * address of the UBO to a clamped offset within the UBO.
-+ */
-+ if (is_mul ||
-+ QPU_GET_FIELD(inst, QPU_OP_ADD) != QPU_A_ADD) {
-+ DRM_ERROR("direct TMU load wasn't an add\n");
-+ return false;
-+ }
-+
-+ /* We assert that the the clamped address is the first
-+ * argument, and the UBO base address is the second argument.
-+ * This is arbitrary, but simpler than supporting flipping the
-+ * two either way.
-+ */
-+ clamp_reg = raddr_add_a_to_live_reg_index(inst);
-+ if (clamp_reg == ~0) {
-+ DRM_ERROR("direct TMU load wasn't clamped\n");
-+ return false;
-+ }
-+
-+ clamp_offset = validation_state->live_min_clamp_offsets[clamp_reg];
-+ if (clamp_offset == ~0) {
-+ DRM_ERROR("direct TMU load wasn't clamped\n");
-+ return false;
-+ }
-+
-+ /* Store the clamp value's offset in p1 (see reloc_tex() in
-+ * vc4_validate.c).
-+ */
-+ validation_state->tmu_setup[tmu].p_offset[1] =
-+ clamp_offset;
-+
-+ if (!(add_b == QPU_MUX_A && raddr_a == QPU_R_UNIF) &&
-+ !(add_b == QPU_MUX_B && raddr_b == QPU_R_UNIF)) {
-+ DRM_ERROR("direct TMU load didn't add to a uniform\n");
-+ return false;
-+ }
-+
-+ validation_state->tmu_setup[tmu].is_direct = true;
-+ } else {
-+ if (raddr_a == QPU_R_UNIF || (sig != QPU_SIG_SMALL_IMM &&
-+ raddr_b == QPU_R_UNIF)) {
-+ DRM_ERROR("uniform read in the same instruction as "
-+ "texture setup.\n");
-+ return false;
-+ }
-+ }
-+
-+ if (validation_state->tmu_write_count[tmu] >= 4) {
-+ DRM_ERROR("TMU%d got too many parameters before dispatch\n",
-+ tmu);
-+ return false;
-+ }
-+ validation_state->tmu_setup[tmu].p_offset[validation_state->tmu_write_count[tmu]] =
-+ validated_shader->uniforms_size;
-+ validation_state->tmu_write_count[tmu]++;
-+ /* Since direct uses a RADDR uniform reference, it will get counted in
-+ * check_instruction_reads()
-+ */
-+ if (!is_direct)
-+ validated_shader->uniforms_size += 4;
-+
-+ if (submit) {
-+ if (!record_validated_texture_sample(validated_shader,
-+ validation_state, tmu)) {
-+ return false;
-+ }
-+
-+ validation_state->tmu_write_count[tmu] = 0;
-+ }
-+
-+ return true;
-+}
-+
-+static bool
-+check_register_write(uint64_t inst,
-+ struct vc4_validated_shader_info *validated_shader,
-+ struct vc4_shader_validation_state *validation_state,
-+ bool is_mul)
-+{
-+ uint32_t waddr = (is_mul ?
-+ QPU_GET_FIELD(inst, QPU_WADDR_MUL) :
-+ QPU_GET_FIELD(inst, QPU_WADDR_ADD));
-+
-+ switch (waddr) {
-+ case QPU_W_UNIFORMS_ADDRESS:
-+ /* XXX: We'll probably need to support this for reladdr, but
-+ * it's definitely a security-related one.
-+ */
-+ DRM_ERROR("uniforms address load unsupported\n");
-+ return false;
-+
-+ case QPU_W_TLB_COLOR_MS:
-+ case QPU_W_TLB_COLOR_ALL:
-+ case QPU_W_TLB_Z:
-+ /* These only interact with the tile buffer, not main memory,
-+ * so they're safe.
-+ */
-+ return true;
-+
-+ case QPU_W_TMU0_S:
-+ case QPU_W_TMU0_T:
-+ case QPU_W_TMU0_R:
-+ case QPU_W_TMU0_B:
-+ case QPU_W_TMU1_S:
-+ case QPU_W_TMU1_T:
-+ case QPU_W_TMU1_R:
-+ case QPU_W_TMU1_B:
-+ return check_tmu_write(inst, validated_shader, validation_state,
-+ is_mul);
-+
-+ case QPU_W_HOST_INT:
-+ case QPU_W_TMU_NOSWAP:
-+ case QPU_W_TLB_ALPHA_MASK:
-+ case QPU_W_MUTEX_RELEASE:
-+ /* XXX: I haven't thought about these, so don't support them
-+ * for now.
-+ */
-+ DRM_ERROR("Unsupported waddr %d\n", waddr);
-+ return false;
-+
-+ case QPU_W_VPM_ADDR:
-+ DRM_ERROR("General VPM DMA unsupported\n");
-+ return false;
-+
-+ case QPU_W_VPM:
-+ case QPU_W_VPMVCD_SETUP:
-+ /* We allow VPM setup in general, even including VPM DMA
-+ * configuration setup, because the (unsafe) DMA can only be
-+ * triggered by QPU_W_VPM_ADDR writes.
-+ */
-+ return true;
-+
-+ case QPU_W_TLB_STENCIL_SETUP:
-+ return true;
-+ }
-+
-+ return true;
-+}
-+
-+static void
-+track_live_clamps(uint64_t inst,
-+ struct vc4_validated_shader_info *validated_shader,
-+ struct vc4_shader_validation_state *validation_state)
-+{
-+ uint32_t op_add = QPU_GET_FIELD(inst, QPU_OP_ADD);
-+ uint32_t waddr_add = QPU_GET_FIELD(inst, QPU_WADDR_ADD);
-+ uint32_t waddr_mul = QPU_GET_FIELD(inst, QPU_WADDR_MUL);
-+ uint32_t cond_add = QPU_GET_FIELD(inst, QPU_COND_ADD);
-+ uint32_t add_a = QPU_GET_FIELD(inst, QPU_ADD_A);
-+ uint32_t add_b = QPU_GET_FIELD(inst, QPU_ADD_B);
-+ uint32_t raddr_a = QPU_GET_FIELD(inst, QPU_RADDR_A);
-+ uint32_t raddr_b = QPU_GET_FIELD(inst, QPU_RADDR_B);
-+ uint32_t sig = QPU_GET_FIELD(inst, QPU_SIG);
-+ bool ws = inst & QPU_WS;
-+ uint32_t lri_add_a, lri_add, lri_mul;
-+ bool add_a_is_min_0;
-+
-+ /* Check whether OP_ADD's A argumennt comes from a live MAX(x, 0),
-+ * before we clear previous live state.
-+ */
-+ lri_add_a = raddr_add_a_to_live_reg_index(inst);
-+ add_a_is_min_0 = (lri_add_a != ~0 &&
-+ validation_state->live_max_clamp_regs[lri_add_a]);
-+
-+ /* Clear live state for registers written by our instruction. */
-+ lri_add = waddr_to_live_reg_index(waddr_add, ws);
-+ lri_mul = waddr_to_live_reg_index(waddr_mul, !ws);
-+ if (lri_mul != ~0) {
-+ validation_state->live_max_clamp_regs[lri_mul] = false;
-+ validation_state->live_min_clamp_offsets[lri_mul] = ~0;
-+ }
-+ if (lri_add != ~0) {
-+ validation_state->live_max_clamp_regs[lri_add] = false;
-+ validation_state->live_min_clamp_offsets[lri_add] = ~0;
-+ } else {
-+ /* Nothing further to do for live tracking, since only ADDs
-+ * generate new live clamp registers.
-+ */
-+ return;
-+ }
-+
-+ /* Now, handle remaining live clamp tracking for the ADD operation. */
-+
-+ if (cond_add != QPU_COND_ALWAYS)
-+ return;
-+
-+ if (op_add == QPU_A_MAX) {
-+ /* Track live clamps of a value to a minimum of 0 (in either
-+ * arg).
-+ */
-+ if (sig != QPU_SIG_SMALL_IMM || raddr_b != 0 ||
-+ (add_a != QPU_MUX_B && add_b != QPU_MUX_B)) {
-+ return;
-+ }
-+
-+ validation_state->live_max_clamp_regs[lri_add] = true;
-+ } if (op_add == QPU_A_MIN) {
-+ /* Track live clamps of a value clamped to a minimum of 0 and
-+ * a maximum of some uniform's offset.
-+ */
-+ if (!add_a_is_min_0)
-+ return;
-+
-+ if (!(add_b == QPU_MUX_A && raddr_a == QPU_R_UNIF) &&
-+ !(add_b == QPU_MUX_B && raddr_b == QPU_R_UNIF &&
-+ sig != QPU_SIG_SMALL_IMM)) {
-+ return;
-+ }
-+
-+ validation_state->live_min_clamp_offsets[lri_add] =
-+ validated_shader->uniforms_size;
-+ }
-+}
-+
-+static bool
-+check_instruction_writes(uint64_t inst,
-+ struct vc4_validated_shader_info *validated_shader,
-+ struct vc4_shader_validation_state *validation_state)
-+{
-+ uint32_t waddr_add = QPU_GET_FIELD(inst, QPU_WADDR_ADD);
-+ uint32_t waddr_mul = QPU_GET_FIELD(inst, QPU_WADDR_MUL);
-+ bool ok;
-+
-+ if (is_tmu_write(waddr_add) && is_tmu_write(waddr_mul)) {
-+ DRM_ERROR("ADD and MUL both set up textures\n");
-+ return false;
-+ }
-+
-+ ok = (check_register_write(inst, validated_shader, validation_state, false) &&
-+ check_register_write(inst, validated_shader, validation_state, true));
-+
-+ track_live_clamps(inst, validated_shader, validation_state);
-+
-+ return ok;
-+}
-+
-+static bool
-+check_instruction_reads(uint64_t inst,
-+ struct vc4_validated_shader_info *validated_shader)
-+{
-+ uint32_t raddr_a = QPU_GET_FIELD(inst, QPU_RADDR_A);
-+ uint32_t raddr_b = QPU_GET_FIELD(inst, QPU_RADDR_B);
-+ uint32_t sig = QPU_GET_FIELD(inst, QPU_SIG);
-+
-+ if (raddr_a == QPU_R_UNIF ||
-+ (raddr_b == QPU_R_UNIF && sig != QPU_SIG_SMALL_IMM)) {
-+ /* This can't overflow the uint32_t, because we're reading 8
-+ * bytes of instruction to increment by 4 here, so we'd
-+ * already be OOM.
-+ */
-+ validated_shader->uniforms_size += 4;
-+ }
-+
-+ return true;
-+}
-+
-+struct vc4_validated_shader_info *
-+vc4_validate_shader(struct drm_gem_cma_object *shader_obj)
-+{
-+ bool found_shader_end = false;
-+ int shader_end_ip = 0;
-+ uint32_t ip, max_ip;
-+ uint64_t *shader;
-+ struct vc4_validated_shader_info *validated_shader;
-+ struct vc4_shader_validation_state validation_state;
-+ int i;
-+
-+ memset(&validation_state, 0, sizeof(validation_state));
-+
-+ for (i = 0; i < 8; i++)
-+ validation_state.tmu_setup[i / 4].p_offset[i % 4] = ~0;
-+ for (i = 0; i < ARRAY_SIZE(validation_state.live_min_clamp_offsets); i++)
-+ validation_state.live_min_clamp_offsets[i] = ~0;
-+
-+ shader = shader_obj->vaddr;
-+ max_ip = shader_obj->base.size / sizeof(uint64_t);
-+
-+ validated_shader = kcalloc(sizeof(*validated_shader), 1, GFP_KERNEL);
-+ if (!validated_shader)
-+ return NULL;
-+
-+ for (ip = 0; ip < max_ip; ip++) {
-+ uint64_t inst = shader[ip];
-+ uint32_t sig = QPU_GET_FIELD(inst, QPU_SIG);
-+
-+ switch (sig) {
-+ case QPU_SIG_NONE:
-+ case QPU_SIG_WAIT_FOR_SCOREBOARD:
-+ case QPU_SIG_SCOREBOARD_UNLOCK:
-+ case QPU_SIG_COLOR_LOAD:
-+ case QPU_SIG_LOAD_TMU0:
-+ case QPU_SIG_LOAD_TMU1:
-+ case QPU_SIG_PROG_END:
-+ case QPU_SIG_SMALL_IMM:
-+ if (!check_instruction_writes(inst, validated_shader,
-+ &validation_state)) {
-+ DRM_ERROR("Bad write at ip %d\n", ip);
-+ goto fail;
-+ }
-+
-+ if (!check_instruction_reads(inst, validated_shader))
-+ goto fail;
-+
-+ if (sig == QPU_SIG_PROG_END) {
-+ found_shader_end = true;
-+ shader_end_ip = ip;
-+ }
-+
-+ break;
-+
-+ case QPU_SIG_LOAD_IMM:
-+ if (!check_instruction_writes(inst, validated_shader,
-+ &validation_state)) {
-+ DRM_ERROR("Bad LOAD_IMM write at ip %d\n", ip);
-+ goto fail;
-+ }
-+ break;
-+
-+ default:
-+ DRM_ERROR("Unsupported QPU signal %d at "
-+ "instruction %d\n", sig, ip);
-+ goto fail;
-+ }
-+
-+ /* There are two delay slots after program end is signaled
-+ * that are still executed, then we're finished.
-+ */
-+ if (found_shader_end && ip == shader_end_ip + 2)
-+ break;
-+ }
-+
-+ if (ip == max_ip) {
-+ DRM_ERROR("shader failed to terminate before "
-+ "shader BO end at %d\n",
-+ shader_obj->base.size);
-+ goto fail;
-+ }
-+
-+ /* Again, no chance of integer overflow here because the worst case
-+ * scenario is 8 bytes of uniforms plus handles per 8-byte
-+ * instruction.
-+ */
-+ validated_shader->uniforms_src_size =
-+ (validated_shader->uniforms_size +
-+ 4 * validated_shader->num_texture_samples);
-+
-+ return validated_shader;
-+
-+fail:
-+ if (validated_shader) {
-+ kfree(validated_shader->texture_samples);
-+ kfree(validated_shader);
-+ }
-+ return NULL;
-+}
---- /dev/null
-+++ b/include/uapi/drm/vc4_drm.h
-@@ -0,0 +1,229 @@
-+/*
-+ * Copyright © 2014-2015 Broadcom
-+ *
-+ * Permission is hereby granted, free of charge, to any person obtaining a
-+ * copy of this software and associated documentation files (the "Software"),
-+ * to deal in the Software without restriction, including without limitation
-+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
-+ * and/or sell copies of the Software, and to permit persons to whom the
-+ * Software is furnished to do so, subject to the following conditions:
-+ *
-+ * The above copyright notice and this permission notice (including the next
-+ * paragraph) shall be included in all copies or substantial portions of the
-+ * Software.
-+ *
-+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
-+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
-+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
-+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
-+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
-+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS
-+ * IN THE SOFTWARE.
-+ */
-+
-+#ifndef _UAPI_VC4_DRM_H_
-+#define _UAPI_VC4_DRM_H_
-+
-+#include <drm/drm.h>
-+
-+#define DRM_VC4_SUBMIT_CL 0x00
-+#define DRM_VC4_WAIT_SEQNO 0x01
-+#define DRM_VC4_WAIT_BO 0x02
-+#define DRM_VC4_CREATE_BO 0x03
-+#define DRM_VC4_MMAP_BO 0x04
-+#define DRM_VC4_CREATE_SHADER_BO 0x05
-+
-+#define DRM_IOCTL_VC4_SUBMIT_CL DRM_IOWR( DRM_COMMAND_BASE + DRM_VC4_SUBMIT_CL, struct drm_vc4_submit_cl)
-+#define DRM_IOCTL_VC4_WAIT_SEQNO DRM_IOWR( DRM_COMMAND_BASE + DRM_VC4_WAIT_SEQNO, struct drm_vc4_wait_seqno)
-+#define DRM_IOCTL_VC4_WAIT_BO DRM_IOWR( DRM_COMMAND_BASE + DRM_VC4_WAIT_BO, struct drm_vc4_wait_bo)
-+#define DRM_IOCTL_VC4_CREATE_BO DRM_IOWR( DRM_COMMAND_BASE + DRM_VC4_CREATE_BO, struct drm_vc4_create_bo)
-+#define DRM_IOCTL_VC4_MMAP_BO DRM_IOWR( DRM_COMMAND_BASE + DRM_VC4_MMAP_BO, struct drm_vc4_mmap_bo)
-+#define DRM_IOCTL_VC4_CREATE_SHADER_BO DRM_IOWR( DRM_COMMAND_BASE + DRM_VC4_CREATE_SHADER_BO, struct drm_vc4_create_shader_bo)
-+
-+struct drm_vc4_submit_rcl_surface {
-+ uint32_t hindex; /* Handle index, or ~0 if not present. */
-+ uint32_t offset; /* Offset to start of buffer. */
-+ /*
-+ * Bits for either render config (color_ms_write) or load/store packet.
-+ */
-+ uint16_t bits;
-+ uint16_t pad;
-+};
-+
-+/**
-+ * struct drm_vc4_submit_cl - ioctl argument for submitting commands to the 3D
-+ * engine.
-+ *
-+ * Drivers typically use GPU BOs to store batchbuffers / command lists and
-+ * their associated state. However, because the VC4 lacks an MMU, we have to
-+ * do validation of memory accesses by the GPU commands. If we were to store
-+ * our commands in BOs, we'd need to do uncached readback from them to do the
-+ * validation process, which is too expensive. Instead, userspace accumulates
-+ * commands and associated state in plain memory, then the kernel copies the
-+ * data to its own address space, and then validates and stores it in a GPU
-+ * BO.
-+ */
-+struct drm_vc4_submit_cl {
-+ /* Pointer to the binner command list.
-+ *
-+ * This is the first set of commands executed, which runs the
-+ * coordinate shader to determine where primitives land on the screen,
-+ * then writes out the state updates and draw calls necessary per tile
-+ * to the tile allocation BO.
-+ */
-+ uint64_t bin_cl;
-+
-+ /* Pointer to the shader records.
-+ *
-+ * Shader records are the structures read by the hardware that contain
-+ * pointers to uniforms, shaders, and vertex attributes. The
-+ * reference to the shader record has enough information to determine
-+ * how many pointers are necessary (fixed number for shaders/uniforms,
-+ * and an attribute count), so those BO indices into bo_handles are
-+ * just stored as uint32_ts before each shader record passed in.
-+ */
-+ uint64_t shader_rec;
-+
-+ /* Pointer to uniform data and texture handles for the textures
-+ * referenced by the shader.
-+ *
-+ * For each shader state record, there is a set of uniform data in the
-+ * order referenced by the record (FS, VS, then CS). Each set of
-+ * uniform data has a uint32_t index into bo_handles per texture
-+ * sample operation, in the order the QPU_W_TMUn_S writes appear in
-+ * the program. Following the texture BO handle indices is the actual
-+ * uniform data.
-+ *
-+ * The individual uniform state blocks don't have sizes passed in,
-+ * because the kernel has to determine the sizes anyway during shader
-+ * code validation.
-+ */
-+ uint64_t uniforms;
-+ uint64_t bo_handles;
-+
-+ /* Size in bytes of the binner command list. */
-+ uint32_t bin_cl_size;
-+ /* Size in bytes of the set of shader records. */
-+ uint32_t shader_rec_size;
-+ /* Number of shader records.
-+ *
-+ * This could just be computed from the contents of shader_records and
-+ * the address bits of references to them from the bin CL, but it
-+ * keeps the kernel from having to resize some allocations it makes.
-+ */
-+ uint32_t shader_rec_count;
-+ /* Size in bytes of the uniform state. */
-+ uint32_t uniforms_size;
-+
-+ /* Number of BO handles passed in (size is that times 4). */
-+ uint32_t bo_handle_count;
-+
-+ /* RCL setup: */
-+ uint16_t width;
-+ uint16_t height;
-+ uint8_t min_x_tile;
-+ uint8_t min_y_tile;
-+ uint8_t max_x_tile;
-+ uint8_t max_y_tile;
-+ struct drm_vc4_submit_rcl_surface color_read;
-+ struct drm_vc4_submit_rcl_surface color_ms_write;
-+ struct drm_vc4_submit_rcl_surface zs_read;
-+ struct drm_vc4_submit_rcl_surface zs_write;
-+ uint32_t clear_color[2];
-+ uint32_t clear_z;
-+ uint8_t clear_s;
-+
-+ uint32_t pad:24;
-+
-+#define VC4_SUBMIT_CL_USE_CLEAR_COLOR (1 << 0)
-+ uint32_t flags;
-+
-+ /* Returned value of the seqno of this render job (for the
-+ * wait ioctl).
-+ */
-+ uint64_t seqno;
-+};
-+
-+/**
-+ * struct drm_vc4_wait_seqno - ioctl argument for waiting for
-+ * DRM_VC4_SUBMIT_CL completion using its returned seqno.
-+ *
-+ * timeout_ns is the timeout in nanoseconds, where "0" means "don't
-+ * block, just return the status."
-+ */
-+struct drm_vc4_wait_seqno {
-+ uint64_t seqno;
-+ uint64_t timeout_ns;
-+};
-+
-+/**
-+ * struct drm_vc4_wait_bo - ioctl argument for waiting for
-+ * completion of the last DRM_VC4_SUBMIT_CL on a BO.
-+ *
-+ * This is useful for cases where multiple processes might be
-+ * rendering to a BO and you want to wait for all rendering to be
-+ * completed.
-+ */
-+struct drm_vc4_wait_bo {
-+ uint32_t handle;
-+ uint32_t pad;
-+ uint64_t timeout_ns;
-+};
-+
-+/**
-+ * struct drm_vc4_create_bo - ioctl argument for creating VC4 BOs.
-+ *
-+ * There are currently no values for the flags argument, but it may be
-+ * used in a future extension.
-+ */
-+struct drm_vc4_create_bo {
-+ uint32_t size;
-+ uint32_t flags;
-+ /** Returned GEM handle for the BO. */
-+ uint32_t handle;
-+ uint32_t pad;
-+};
-+
-+/**
-+ * struct drm_vc4_create_shader_bo - ioctl argument for creating VC4
-+ * shader BOs.
-+ *
-+ * Since allowing a shader to be overwritten while it's also being
-+ * executed from would allow privlege escalation, shaders must be
-+ * created using this ioctl, and they can't be mmapped later.
-+ */
-+struct drm_vc4_create_shader_bo {
-+ /* Size of the data argument. */
-+ uint32_t size;
-+ /* Flags, currently must be 0. */
-+ uint32_t flags;
-+
-+ /* Pointer to the data. */
-+ uint64_t data;
-+
-+ /** Returned GEM handle for the BO. */
-+ uint32_t handle;
-+ /* Pad, must be 0. */
-+ uint32_t pad;
-+};
-+
-+/**
-+ * struct drm_vc4_mmap_bo - ioctl argument for mapping VC4 BOs.
-+ *
-+ * This doesn't actually perform an mmap. Instead, it returns the
-+ * offset you need to use in an mmap on the DRM device node. This
-+ * means that tools like valgrind end up knowing about the mapped
-+ * memory.
-+ *
-+ * There are currently no values for the flags argument, but it may be
-+ * used in a future extension.
-+ */
-+struct drm_vc4_mmap_bo {
-+ /** Handle for the object being mapped. */
-+ uint32_t handle;
-+ uint32_t flags;
-+ /** offset into the drm node to use for subsequent mmap call. */
-+ uint64_t offset;
-+};
-+
-+#endif /* _UAPI_VC4_DRM_H_ */
diff --git a/target/linux/brcm2708/patches-4.4/0091-drm-vc4-Force-HDMI-to-connected.patch b/target/linux/brcm2708/patches-4.4/0091-drm-vc4-Force-HDMI-to-connected.patch
deleted file mode 100644
index 409ab43..0000000
--- a/target/linux/brcm2708/patches-4.4/0091-drm-vc4-Force-HDMI-to-connected.patch
+++ /dev/null
@@ -1,23 +0,0 @@
-From 9fa2b9ffdec7f13704a7980adeb0fc0ccb2b21a9 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Wed, 14 Oct 2015 11:32:14 -0700
-Subject: [PATCH] drm/vc4: Force HDMI to connected.
-
-For some reason on the downstream tree, the HPD GPIO isn't working.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_hdmi.c | 2 ++
- 1 file changed, 2 insertions(+)
-
---- a/drivers/gpu/drm/vc4/vc4_hdmi.c
-+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
-@@ -164,6 +164,8 @@ vc4_hdmi_connector_detect(struct drm_con
- struct drm_device *dev = connector->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
-
-+ return connector_status_connected;
-+
- if (vc4->hdmi->hpd_gpio) {
- if (gpio_get_value(vc4->hdmi->hpd_gpio))
- return connector_status_connected;
diff --git a/target/linux/brcm2708/patches-4.4/0092-drm-vc4-bo-cache-locking-fixes.patch b/target/linux/brcm2708/patches-4.4/0092-drm-vc4-bo-cache-locking-fixes.patch
deleted file mode 100644
index d67473b..0000000
--- a/target/linux/brcm2708/patches-4.4/0092-drm-vc4-bo-cache-locking-fixes.patch
+++ /dev/null
@@ -1,147 +0,0 @@
-From dd3675cffbae6a8bcd35b07efea807cf7782b257 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 19 Oct 2015 08:23:18 -0700
-Subject: [PATCH] drm/vc4: bo cache locking fixes.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_bo.c | 32 ++++++++++++++++++--------------
- drivers/gpu/drm/vc4/vc4_drv.h | 2 +-
- 2 files changed, 19 insertions(+), 15 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_bo.c
-+++ b/drivers/gpu/drm/vc4/vc4_bo.c
-@@ -112,14 +112,14 @@ void vc4_bo_cache_purge(struct drm_devic
- {
- struct vc4_dev *vc4 = to_vc4_dev(dev);
-
-- spin_lock(&vc4->bo_lock);
-+ mutex_lock(&vc4->bo_lock);
- while (!list_empty(&vc4->bo_cache.time_list)) {
- struct vc4_bo *bo = list_last_entry(&vc4->bo_cache.time_list,
- struct vc4_bo, unref_head);
- vc4_bo_remove_from_cache(bo);
- vc4_bo_destroy(bo);
- }
-- spin_unlock(&vc4->bo_lock);
-+ mutex_unlock(&vc4->bo_lock);
- }
-
- struct vc4_bo *vc4_bo_create(struct drm_device *dev, size_t unaligned_size)
-@@ -134,18 +134,18 @@ struct vc4_bo *vc4_bo_create(struct drm_
- return NULL;
-
- /* First, try to get a vc4_bo from the kernel BO cache. */
-- spin_lock(&vc4->bo_lock);
-+ mutex_lock(&vc4->bo_lock);
- if (page_index < vc4->bo_cache.size_list_size &&
- !list_empty(&vc4->bo_cache.size_list[page_index])) {
- struct vc4_bo *bo =
- list_first_entry(&vc4->bo_cache.size_list[page_index],
- struct vc4_bo, size_head);
- vc4_bo_remove_from_cache(bo);
-- spin_unlock(&vc4->bo_lock);
-+ mutex_unlock(&vc4->bo_lock);
- kref_init(&bo->base.base.refcount);
- return bo;
- }
-- spin_unlock(&vc4->bo_lock);
-+ mutex_unlock(&vc4->bo_lock);
-
- /* Otherwise, make a new BO. */
- for (pass = 0; ; pass++) {
-@@ -215,7 +215,7 @@ vc4_bo_cache_free_old(struct drm_device
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- unsigned long expire_time = jiffies - msecs_to_jiffies(1000);
-
-- spin_lock(&vc4->bo_lock);
-+ mutex_lock(&vc4->bo_lock);
- while (!list_empty(&vc4->bo_cache.time_list)) {
- struct vc4_bo *bo = list_last_entry(&vc4->bo_cache.time_list,
- struct vc4_bo, unref_head);
-@@ -223,14 +223,14 @@ vc4_bo_cache_free_old(struct drm_device
- mod_timer(&vc4->bo_cache.time_timer,
- round_jiffies_up(jiffies +
- msecs_to_jiffies(1000)));
-- spin_unlock(&vc4->bo_lock);
-+ mutex_unlock(&vc4->bo_lock);
- return;
- }
-
- vc4_bo_remove_from_cache(bo);
- vc4_bo_destroy(bo);
- }
-- spin_unlock(&vc4->bo_lock);
-+ mutex_unlock(&vc4->bo_lock);
- }
-
- /* Called on the last userspace/kernel unreference of the BO. Returns
-@@ -248,21 +248,25 @@ void vc4_free_object(struct drm_gem_obje
- /* If the object references someone else's memory, we can't cache it.
- */
- if (gem_bo->import_attach) {
-+ mutex_lock(&vc4->bo_lock);
- vc4_bo_destroy(bo);
-+ mutex_unlock(&vc4->bo_lock);
- return;
- }
-
- /* Don't cache if it was publicly named. */
- if (gem_bo->name) {
-+ mutex_lock(&vc4->bo_lock);
- vc4_bo_destroy(bo);
-+ mutex_unlock(&vc4->bo_lock);
- return;
- }
-
-- spin_lock(&vc4->bo_lock);
-+ mutex_lock(&vc4->bo_lock);
- cache_list = vc4_get_cache_list_for_size(dev, gem_bo->size);
- if (!cache_list) {
- vc4_bo_destroy(bo);
-- spin_unlock(&vc4->bo_lock);
-+ mutex_unlock(&vc4->bo_lock);
- return;
- }
-
-@@ -278,7 +282,7 @@ void vc4_free_object(struct drm_gem_obje
-
- vc4->bo_stats.num_cached++;
- vc4->bo_stats.size_cached += gem_bo->size;
-- spin_unlock(&vc4->bo_lock);
-+ mutex_unlock(&vc4->bo_lock);
-
- vc4_bo_cache_free_old(dev);
- }
-@@ -465,7 +469,7 @@ void vc4_bo_cache_init(struct drm_device
- {
- struct vc4_dev *vc4 = to_vc4_dev(dev);
-
-- spin_lock_init(&vc4->bo_lock);
-+ mutex_init(&vc4->bo_lock);
-
- INIT_LIST_HEAD(&vc4->bo_cache.time_list);
-
-@@ -498,9 +502,9 @@ int vc4_bo_stats_debugfs(struct seq_file
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_bo_stats stats;
-
-- spin_lock(&vc4->bo_lock);
-+ mutex_lock(&vc4->bo_lock);
- stats = vc4->bo_stats;
-- spin_unlock(&vc4->bo_lock);
-+ mutex_unlock(&vc4->bo_lock);
-
- seq_printf(m, "num bos allocated: %d\n", stats.num_allocated);
- seq_printf(m, "size bos allocated: %dkb\n", stats.size_allocated / 1024);
---- a/drivers/gpu/drm/vc4/vc4_drv.h
-+++ b/drivers/gpu/drm/vc4/vc4_drv.h
-@@ -49,7 +49,7 @@ struct vc4_dev {
- } bo_stats;
-
- /* Protects bo_cache and the BO stats. */
-- spinlock_t bo_lock;
-+ struct mutex bo_lock;
-
- /* Sequence number for the last job queued in job_list.
- * Starts at 0 (no jobs emitted).
diff --git a/target/linux/brcm2708/patches-4.4/0093-drm-vc4-bo-cache-locking-cleanup.patch b/target/linux/brcm2708/patches-4.4/0093-drm-vc4-bo-cache-locking-cleanup.patch
deleted file mode 100644
index b919d92..0000000
--- a/target/linux/brcm2708/patches-4.4/0093-drm-vc4-bo-cache-locking-cleanup.patch
+++ /dev/null
@@ -1,92 +0,0 @@
-From 2588849ca1efc5766a36bac287b7a7754c7191e1 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 19 Oct 2015 08:29:41 -0700
-Subject: [PATCH] drm/vc4: bo cache locking cleanup.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_bo.c | 22 +++++++++-------------
- 1 file changed, 9 insertions(+), 13 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_bo.c
-+++ b/drivers/gpu/drm/vc4/vc4_bo.c
-@@ -215,7 +215,6 @@ vc4_bo_cache_free_old(struct drm_device
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- unsigned long expire_time = jiffies - msecs_to_jiffies(1000);
-
-- mutex_lock(&vc4->bo_lock);
- while (!list_empty(&vc4->bo_cache.time_list)) {
- struct vc4_bo *bo = list_last_entry(&vc4->bo_cache.time_list,
- struct vc4_bo, unref_head);
-@@ -223,14 +222,12 @@ vc4_bo_cache_free_old(struct drm_device
- mod_timer(&vc4->bo_cache.time_timer,
- round_jiffies_up(jiffies +
- msecs_to_jiffies(1000)));
-- mutex_unlock(&vc4->bo_lock);
- return;
- }
-
- vc4_bo_remove_from_cache(bo);
- vc4_bo_destroy(bo);
- }
-- mutex_unlock(&vc4->bo_lock);
- }
-
- /* Called on the last userspace/kernel unreference of the BO. Returns
-@@ -245,29 +242,24 @@ void vc4_free_object(struct drm_gem_obje
- struct vc4_bo *bo = to_vc4_bo(gem_bo);
- struct list_head *cache_list;
-
-+ mutex_lock(&vc4->bo_lock);
- /* If the object references someone else's memory, we can't cache it.
- */
- if (gem_bo->import_attach) {
-- mutex_lock(&vc4->bo_lock);
- vc4_bo_destroy(bo);
-- mutex_unlock(&vc4->bo_lock);
-- return;
-+ goto out;
- }
-
- /* Don't cache if it was publicly named. */
- if (gem_bo->name) {
-- mutex_lock(&vc4->bo_lock);
- vc4_bo_destroy(bo);
-- mutex_unlock(&vc4->bo_lock);
-- return;
-+ goto out;
- }
-
-- mutex_lock(&vc4->bo_lock);
- cache_list = vc4_get_cache_list_for_size(dev, gem_bo->size);
- if (!cache_list) {
- vc4_bo_destroy(bo);
-- mutex_unlock(&vc4->bo_lock);
-- return;
-+ goto out;
- }
-
- if (bo->validated_shader) {
-@@ -282,9 +274,11 @@ void vc4_free_object(struct drm_gem_obje
-
- vc4->bo_stats.num_cached++;
- vc4->bo_stats.size_cached += gem_bo->size;
-- mutex_unlock(&vc4->bo_lock);
-
- vc4_bo_cache_free_old(dev);
-+
-+out:
-+ mutex_unlock(&vc4->bo_lock);
- }
-
- static void vc4_bo_cache_time_work(struct work_struct *work)
-@@ -293,7 +287,9 @@ static void vc4_bo_cache_time_work(struc
- container_of(work, struct vc4_dev, bo_cache.time_work);
- struct drm_device *dev = vc4->dev;
-
-+ mutex_lock(&vc4->bo_lock);
- vc4_bo_cache_free_old(dev);
-+ mutex_unlock(&vc4->bo_lock);
- }
-
- static void vc4_bo_cache_time_timer(unsigned long data)
diff --git a/target/linux/brcm2708/patches-4.4/0094-drm-vc4-Use-job_lock-to-protect-seqno_cb_list.patch b/target/linux/brcm2708/patches-4.4/0094-drm-vc4-Use-job_lock-to-protect-seqno_cb_list.patch
deleted file mode 100644
index d9d1048..0000000
--- a/target/linux/brcm2708/patches-4.4/0094-drm-vc4-Use-job_lock-to-protect-seqno_cb_list.patch
+++ /dev/null
@@ -1,54 +0,0 @@
-From cfa018eec8227589076e45fd65f654e525349ff5 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 19 Oct 2015 08:32:24 -0700
-Subject: [PATCH] drm/vc4: Use job_lock to protect seqno_cb_list.
-
-We're (mostly) not supposed to be using struct_mutex in drivers these
-days.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_gem.c | 8 +++++---
- 1 file changed, 5 insertions(+), 3 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -474,7 +474,6 @@ vc4_job_handle_completed(struct vc4_dev
- vc4_complete_exec(exec);
- spin_lock_irqsave(&vc4->job_lock, irqflags);
- }
-- spin_unlock_irqrestore(&vc4->job_lock, irqflags);
-
- list_for_each_entry_safe(cb, cb_temp, &vc4->seqno_cb_list, work.entry) {
- if (cb->seqno <= vc4->finished_seqno) {
-@@ -482,6 +481,8 @@ vc4_job_handle_completed(struct vc4_dev
- schedule_work(&cb->work);
- }
- }
-+
-+ spin_unlock_irqrestore(&vc4->job_lock, irqflags);
- }
-
- static void vc4_seqno_cb_work(struct work_struct *work)
-@@ -496,18 +497,19 @@ int vc4_queue_seqno_cb(struct drm_device
- {
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- int ret = 0;
-+ unsigned long irqflags;
-
- cb->func = func;
- INIT_WORK(&cb->work, vc4_seqno_cb_work);
-
-- mutex_lock(&dev->struct_mutex);
-+ spin_lock_irqsave(&vc4->job_lock, irqflags);
- if (seqno > vc4->finished_seqno) {
- cb->seqno = seqno;
- list_add_tail(&cb->work.entry, &vc4->seqno_cb_list);
- } else {
- schedule_work(&cb->work);
- }
-- mutex_unlock(&dev->struct_mutex);
-+ spin_unlock_irqrestore(&vc4->job_lock, irqflags);
-
- return ret;
- }
diff --git a/target/linux/brcm2708/patches-4.4/0095-drm-vc4-Drop-struct_mutex-around-CL-validation.patch b/target/linux/brcm2708/patches-4.4/0095-drm-vc4-Drop-struct_mutex-around-CL-validation.patch
deleted file mode 100644
index d09d8a1..0000000
--- a/target/linux/brcm2708/patches-4.4/0095-drm-vc4-Drop-struct_mutex-around-CL-validation.patch
+++ /dev/null
@@ -1,63 +0,0 @@
-From 42dd8243cc7c8870c01f245dab252391375384ef Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 19 Oct 2015 08:44:35 -0700
-Subject: [PATCH] drm/vc4: Drop struct_mutex around CL validation.
-
-We were using it so that we could make sure that shader validation
-state didn't change while we were validating, but now shader
-validation state is immutable. The bcl/rcl generation doesn't do any
-other BO dereferencing, and seems to have no other global state
-dependency not covered by job_lock / bo_lock.
-
-Fixes a lock order reversal between mmap_sem and struct_mutex.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_gem.c | 12 ++++--------
- 1 file changed, 4 insertions(+), 8 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -244,13 +244,15 @@ static void
- vc4_queue_submit(struct drm_device *dev, struct vc4_exec_info *exec)
- {
- struct vc4_dev *vc4 = to_vc4_dev(dev);
-- uint64_t seqno = ++vc4->emit_seqno;
-+ uint64_t seqno;
- unsigned long irqflags;
-
-+ spin_lock_irqsave(&vc4->job_lock, irqflags);
-+
-+ seqno = ++vc4->emit_seqno;
- exec->seqno = seqno;
- vc4_update_bo_seqnos(exec, seqno);
-
-- spin_lock_irqsave(&vc4->job_lock, irqflags);
- list_add_tail(&exec->head, &vc4->job_list);
-
- /* If no job was executing, kick ours off. Otherwise, it'll
-@@ -608,8 +610,6 @@ vc4_submit_cl_ioctl(struct drm_device *d
- exec->args = args;
- INIT_LIST_HEAD(&exec->unref_list);
-
-- mutex_lock(&dev->struct_mutex);
--
- ret = vc4_cl_lookup_bos(dev, file_priv, exec);
- if (ret)
- goto fail;
-@@ -636,15 +636,11 @@ vc4_submit_cl_ioctl(struct drm_device *d
- /* Return the seqno for our job. */
- args->seqno = vc4->emit_seqno;
-
-- mutex_unlock(&dev->struct_mutex);
--
- return 0;
-
- fail:
- vc4_complete_exec(exec);
-
-- mutex_unlock(&dev->struct_mutex);
--
- return ret;
- }
-
diff --git a/target/linux/brcm2708/patches-4.4/0096-drm-vc4-Drop-struct_mutex-around-CL-validation.patch b/target/linux/brcm2708/patches-4.4/0096-drm-vc4-Drop-struct_mutex-around-CL-validation.patch
deleted file mode 100644
index 564e08c..0000000
--- a/target/linux/brcm2708/patches-4.4/0096-drm-vc4-Drop-struct_mutex-around-CL-validation.patch
+++ /dev/null
@@ -1,74 +0,0 @@
-From 22dd367f4b6b819b4b84e0b09cd7a16f00e641a9 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 19 Oct 2015 08:44:35 -0700
-Subject: [PATCH] drm/vc4: Drop struct_mutex around CL validation.
-
-We were using it so that we could make sure that shader validation
-state didn't change while we were validating, but now shader
-validation state is immutable. The bcl/rcl generation doesn't do any
-other BO dereferencing, and seems to have no other global state
-dependency not covered by job_lock / bo_lock. We only need to hold
-struct_mutex for object unreferencing.
-
-Fixes a lock order reversal between mmap_sem and struct_mutex.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_gem.c | 13 ++++++-------
- 1 file changed, 6 insertions(+), 7 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -439,10 +439,12 @@ fail:
- }
-
- static void
--vc4_complete_exec(struct vc4_exec_info *exec)
-+vc4_complete_exec(struct drm_device *dev, struct vc4_exec_info *exec)
- {
- unsigned i;
-
-+ /* Need the struct lock for drm_gem_object_unreference(). */
-+ mutex_lock(&dev->struct_mutex);
- if (exec->bo) {
- for (i = 0; i < exec->bo_count; i++)
- drm_gem_object_unreference(&exec->bo[i].bo->base);
-@@ -455,6 +457,7 @@ vc4_complete_exec(struct vc4_exec_info *
- list_del(&bo->unref_head);
- drm_gem_object_unreference(&bo->base.base);
- }
-+ mutex_unlock(&dev->struct_mutex);
-
- kfree(exec);
- }
-@@ -473,7 +476,7 @@ vc4_job_handle_completed(struct vc4_dev
- list_del(&exec->head);
-
- spin_unlock_irqrestore(&vc4->job_lock, irqflags);
-- vc4_complete_exec(exec);
-+ vc4_complete_exec(vc4->dev, exec);
- spin_lock_irqsave(&vc4->job_lock, irqflags);
- }
-
-@@ -525,12 +528,8 @@ vc4_job_done_work(struct work_struct *wo
- {
- struct vc4_dev *vc4 =
- container_of(work, struct vc4_dev, job_done_work);
-- struct drm_device *dev = vc4->dev;
-
-- /* Need the struct lock for drm_gem_object_unreference(). */
-- mutex_lock(&dev->struct_mutex);
- vc4_job_handle_completed(vc4);
-- mutex_unlock(&dev->struct_mutex);
- }
-
- static int
-@@ -639,7 +638,7 @@ vc4_submit_cl_ioctl(struct drm_device *d
- return 0;
-
- fail:
-- vc4_complete_exec(exec);
-+ vc4_complete_exec(vc4->dev, exec);
-
- return ret;
- }
diff --git a/target/linux/brcm2708/patches-4.4/0097-drm-vc4-Add-support-for-more-display-plane-formats.patch b/target/linux/brcm2708/patches-4.4/0097-drm-vc4-Add-support-for-more-display-plane-formats.patch
deleted file mode 100644
index e6653d7..0000000
--- a/target/linux/brcm2708/patches-4.4/0097-drm-vc4-Add-support-for-more-display-plane-formats.patch
+++ /dev/null
@@ -1,35 +0,0 @@
-From 09487bfe004a2567c1b64420a403d352cc4385e9 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 20 Oct 2015 13:59:15 +0100
-Subject: [PATCH] drm/vc4: Add support for more display plane formats.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_plane.c | 16 ++++++++++++++++
- 1 file changed, 16 insertions(+)
-
---- a/drivers/gpu/drm/vc4/vc4_plane.c
-+++ b/drivers/gpu/drm/vc4/vc4_plane.c
-@@ -59,6 +59,22 @@ static const struct hvs_format {
- .drm = DRM_FORMAT_ARGB8888, .hvs = HVS_PIXEL_FORMAT_RGBA8888,
- .pixel_order = HVS_PIXEL_ORDER_ABGR, .has_alpha = true,
- },
-+ {
-+ .drm = DRM_FORMAT_RGB565, .hvs = HVS_PIXEL_FORMAT_RGB565,
-+ .pixel_order = HVS_PIXEL_ORDER_XRGB, .has_alpha = false,
-+ },
-+ {
-+ .drm = DRM_FORMAT_BGR565, .hvs = HVS_PIXEL_FORMAT_RGB565,
-+ .pixel_order = HVS_PIXEL_ORDER_XBGR, .has_alpha = false,
-+ },
-+ {
-+ .drm = DRM_FORMAT_ARGB1555, .hvs = HVS_PIXEL_FORMAT_RGBA5551,
-+ .pixel_order = HVS_PIXEL_ORDER_ABGR, .has_alpha = true,
-+ },
-+ {
-+ .drm = DRM_FORMAT_XRGB1555, .hvs = HVS_PIXEL_FORMAT_RGBA5551,
-+ .pixel_order = HVS_PIXEL_ORDER_ABGR, .has_alpha = false,
-+ },
- };
-
- static const struct hvs_format *vc4_get_hvs_format(u32 drm_format)
diff --git a/target/linux/brcm2708/patches-4.4/0098-drm-vc4-No-need-to-stop-the-stopped-threads.patch b/target/linux/brcm2708/patches-4.4/0098-drm-vc4-No-need-to-stop-the-stopped-threads.patch
deleted file mode 100644
index c9f4819..0000000
--- a/target/linux/brcm2708/patches-4.4/0098-drm-vc4-No-need-to-stop-the-stopped-threads.patch
+++ /dev/null
@@ -1,26 +0,0 @@
-From 7f9ae98f26324649817bc9c66d9cfdaa9eed825d Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 23 Oct 2015 12:31:56 +0100
-Subject: [PATCH] drm/vc4: No need to stop the stopped threads.
-
-This was leftover debug code from the hackdriver. We never submit
-unless the thread is already idle.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_gem.c | 4 ----
- 1 file changed, 4 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -104,10 +104,6 @@ submit_cl(struct drm_device *dev, uint32
- {
- struct vc4_dev *vc4 = to_vc4_dev(dev);
-
-- /* Stop any existing thread and set state to "stopped at halt" */
-- V3D_WRITE(V3D_CTNCS(thread), V3D_CTRUN);
-- barrier();
--
- V3D_WRITE(V3D_CTNCA(thread), start);
- barrier();
-
diff --git a/target/linux/brcm2708/patches-4.4/0099-drm-vc4-Remove-extra-barrier-s-aroudn-CTnCA-CTnEA-se.patch b/target/linux/brcm2708/patches-4.4/0099-drm-vc4-Remove-extra-barrier-s-aroudn-CTnCA-CTnEA-se.patch
deleted file mode 100644
index d9eca64..0000000
--- a/target/linux/brcm2708/patches-4.4/0099-drm-vc4-Remove-extra-barrier-s-aroudn-CTnCA-CTnEA-se.patch
+++ /dev/null
@@ -1,32 +0,0 @@
-From aa3b53bc69a07d03622a65a82843ba2fa4ff7b89 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 23 Oct 2015 12:33:43 +0100
-Subject: [PATCH] drm/vc4: Remove extra barrier()s aroudn CTnCA/CTnEA setup.
-
-The writel() that these expand to already does barriers.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_gem.c | 9 +++------
- 1 file changed, 3 insertions(+), 6 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -104,14 +104,11 @@ submit_cl(struct drm_device *dev, uint32
- {
- struct vc4_dev *vc4 = to_vc4_dev(dev);
-
-- V3D_WRITE(V3D_CTNCA(thread), start);
-- barrier();
--
-- /* Set the end address of the control list. Writing this
-- * register is what starts the job.
-+ /* Set the current and end address of the control list.
-+ * Writing the end register is what starts the job.
- */
-+ V3D_WRITE(V3D_CTNCA(thread), start);
- V3D_WRITE(V3D_CTNEA(thread), end);
-- barrier();
- }
-
- int
diff --git a/target/linux/brcm2708/patches-4.4/0100-drm-vc4-Fix-a-typo-in-a-V3D-debug-register.patch b/target/linux/brcm2708/patches-4.4/0100-drm-vc4-Fix-a-typo-in-a-V3D-debug-register.patch
deleted file mode 100644
index 80dd55f..0000000
--- a/target/linux/brcm2708/patches-4.4/0100-drm-vc4-Fix-a-typo-in-a-V3D-debug-register.patch
+++ /dev/null
@@ -1,33 +0,0 @@
-From 3748a60377cb3f634c7e0ef209c6d67064266f61 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 23 Oct 2015 14:57:22 +0100
-Subject: [PATCH] drm/vc4: Fix a typo in a V3D debug register.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_regs.h | 2 +-
- drivers/gpu/drm/vc4/vc4_v3d.c | 2 +-
- 2 files changed, 2 insertions(+), 2 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_regs.h
-+++ b/drivers/gpu/drm/vc4/vc4_regs.h
-@@ -154,7 +154,7 @@
- #define V3D_PCTRS14 0x006f4
- #define V3D_PCTR15 0x006f8
- #define V3D_PCTRS15 0x006fc
--#define V3D_BGE 0x00f00
-+#define V3D_DBGE 0x00f00
- #define V3D_FDBGO 0x00f04
- #define V3D_FDBGB 0x00f08
- #define V3D_FDBGR 0x00f0c
---- a/drivers/gpu/drm/vc4/vc4_v3d.c
-+++ b/drivers/gpu/drm/vc4/vc4_v3d.c
-@@ -99,7 +99,7 @@ static const struct {
- REGDEF(V3D_PCTRS14),
- REGDEF(V3D_PCTR15),
- REGDEF(V3D_PCTRS15),
-- REGDEF(V3D_BGE),
-+ REGDEF(V3D_DBGE),
- REGDEF(V3D_FDBGO),
- REGDEF(V3D_FDBGB),
- REGDEF(V3D_FDBGR),
diff --git a/target/linux/brcm2708/patches-4.4/0101-drm-vc4-Enable-VC4-modules-and-increase-CMA-size-wit.patch b/target/linux/brcm2708/patches-4.4/0101-drm-vc4-Enable-VC4-modules-and-increase-CMA-size-wit.patch
deleted file mode 100644
index 4fd09e5..0000000
--- a/target/linux/brcm2708/patches-4.4/0101-drm-vc4-Enable-VC4-modules-and-increase-CMA-size-wit.patch
+++ /dev/null
@@ -1,153 +0,0 @@
-From 61033cab2bce9fdb3cb9816872757e9905702b5b Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 2 Nov 2015 17:07:33 +0000
-Subject: [PATCH] drm/vc4: Enable VC4 modules, and increase CMA size with
- overlay
-
-If using the overlay, be careful not to boot to GUI or run startx,
-or the Pi will almost hang, reporting stalls in kernel threads.
----
- arch/arm/boot/dts/overlays/README | 8 ++
- arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts | 95 ++++++++++++++++++++++
- arch/arm/configs/bcm2709_defconfig | 2 +
- arch/arm/configs/bcmrpi_defconfig | 2 +
- 4 files changed, 107 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -601,6 +601,14 @@ Params: txd1_pin GPIO pi
- rxd1_pin GPIO pin for RXD1 (15, 33 or 41 - default 15)
-
-
-+Name: vc4-kms-v3d
-+Info: Enable Eric Anholt's DRM VC4 HDMI/HVS/V3D driver. Running startx or
-+ booting to GUI while this overlay is in use will cause interesting
-+ lockups.
-+Load: dtoverlay=vc4-kms-v3d
-+Params: <None>
-+
-+
- Name: vga666
- Info: Overlay for the Fen Logic VGA666 board
- This uses GPIOs 2-21 (so no I2C), and activates the output 2-3 seconds
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts
-@@ -0,0 +1,95 @@
-+/*
-+ * vc4-kms-v3d-overlay.dts
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+#include "dt-bindings/clock/bcm2835.h"
-+#include "dt-bindings/gpio/gpio.h"
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&i2c2>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&cprman>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&fb>;
-+ __overlay__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ fragment at 3 {
-+ target = <&soc>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+
-+ pixelvalve at 7e206000 {
-+ compatible = "brcm,bcm2835-pixelvalve0";
-+ reg = <0x7e206000 0x100>;
-+ interrupts = <2 13>; /* pwa0 */
-+ };
-+
-+ pixelvalve at 7e207000 {
-+ compatible = "brcm,bcm2835-pixelvalve1";
-+ reg = <0x7e207000 0x100>;
-+ interrupts = <2 14>; /* pwa1 */
-+ };
-+
-+ hvs at 7e400000 {
-+ compatible = "brcm,bcm2835-hvs";
-+ reg = <0x7e400000 0x6000>;
-+ interrupts = <2 1>;
-+ };
-+
-+ pixelvalve at 7e807000 {
-+ compatible = "brcm,bcm2835-pixelvalve2";
-+ reg = <0x7e807000 0x100>;
-+ interrupts = <2 10>; /* pixelvalve */
-+ };
-+
-+ hdmi at 7e902000 {
-+ compatible = "brcm,bcm2835-hdmi";
-+ reg = <0x7e902000 0x600>,
-+ <0x7e808000 0x100>;
-+ interrupts = <2 8>, <2 9>;
-+ ddc = <&i2c2>;
-+ hpd-gpio = <&gpio 46 GPIO_ACTIVE_HIGH>;
-+ clocks = <&cprman BCM2835_PLLH_PIX>,
-+ <&cprman BCM2835_CLOCK_HSM>;
-+ clock-names = "pixel", "hdmi";
-+ };
-+
-+ v3d at 7ec00000 {
-+ compatible = "brcm,vc4-v3d";
-+ reg = <0x7ec00000 0x1000>;
-+ interrupts = <1 10>;
-+ };
-+
-+ gpu at 7e4c0000 {
-+ compatible = "brcm,bcm2835-vc4";
-+ };
-+ };
-+ };
-+
-+ fragment at 4 {
-+ target-path = "/chosen";
-+ __overlay__ {
-+ bootargs = "cma=256M at 512M";
-+ };
-+ };
-+};
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -802,6 +802,8 @@ CONFIG_VIDEO_TW9903=m
- CONFIG_VIDEO_TW9906=m
- CONFIG_VIDEO_OV7640=m
- CONFIG_VIDEO_MT9V011=m
-+CONFIG_DRM=m
-+CONFIG_DRM_VC4=m
- CONFIG_FB=y
- CONFIG_FB_BCM2708=y
- CONFIG_FB_UDL=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -795,6 +795,8 @@ CONFIG_VIDEO_TW9903=m
- CONFIG_VIDEO_TW9906=m
- CONFIG_VIDEO_OV7640=m
- CONFIG_VIDEO_MT9V011=m
-+CONFIG_DRM=m
-+CONFIG_DRM_VC4=m
- CONFIG_FB=y
- CONFIG_FB_BCM2708=y
- CONFIG_FB_UDL=m
diff --git a/target/linux/brcm2708/patches-4.4/0102-squash-fixups.patch b/target/linux/brcm2708/patches-4.4/0102-squash-fixups.patch
deleted file mode 100644
index f3ba35b..0000000
--- a/target/linux/brcm2708/patches-4.4/0102-squash-fixups.patch
+++ /dev/null
@@ -1,43 +0,0 @@
-From 25c65d9787d6d6bb39ac41f66bd4c9e386e23a78 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Wed, 18 Nov 2015 18:29:58 +0000
-Subject: [PATCH] squash: fixups
-
----
- drivers/gpu/drm/vc4/Kconfig | 2 +-
- drivers/gpu/drm/vc4/vc4_drv.c | 2 +-
- drivers/gpu/drm/vc4/vc4_kms.c | 2 +-
- 3 files changed, 3 insertions(+), 3 deletions(-)
-
---- a/drivers/gpu/drm/vc4/Kconfig
-+++ b/drivers/gpu/drm/vc4/Kconfig
-@@ -1,6 +1,6 @@
- config DRM_VC4
- tristate "Broadcom VC4 Graphics"
-- depends on ARCH_BCM2835 || COMPILE_TEST
-+ depends on ARCH_BCM2835 || ARCH_BCM2708 || ARCH_BCM2709 || COMPILE_TEST
- depends on DRM && HAVE_DMA_ATTRS
- select DRM_KMS_HELPER
- select DRM_KMS_CMA_HELPER
---- a/drivers/gpu/drm/vc4/vc4_drv.c
-+++ b/drivers/gpu/drm/vc4/vc4_drv.c
-@@ -127,7 +127,7 @@ static struct drm_driver vc4_drm_driver
- .num_ioctls = ARRAY_SIZE(vc4_drm_ioctls),
- .fops = &vc4_drm_fops,
-
-- .gem_obj_size = sizeof(struct vc4_bo),
-+ //.gem_obj_size = sizeof(struct vc4_bo),
-
- .name = DRIVER_NAME,
- .desc = DRIVER_DESC,
---- a/drivers/gpu/drm/vc4/vc4_kms.c
-+++ b/drivers/gpu/drm/vc4/vc4_kms.c
-@@ -45,7 +45,7 @@ vc4_atomic_complete_commit(struct vc4_co
-
- drm_atomic_helper_commit_modeset_disables(dev, state);
-
-- drm_atomic_helper_commit_planes(dev, state);
-+ drm_atomic_helper_commit_planes(dev, state, false);
-
- drm_atomic_helper_commit_modeset_enables(dev, state);
-
diff --git a/target/linux/brcm2708/patches-4.4/0103-squash-add-missing-vc4-kms-v3d-overlay.dtb-to-makefi.patch b/target/linux/brcm2708/patches-4.4/0103-squash-add-missing-vc4-kms-v3d-overlay.dtb-to-makefi.patch
deleted file mode 100644
index 886b278..0000000
--- a/target/linux/brcm2708/patches-4.4/0103-squash-add-missing-vc4-kms-v3d-overlay.dtb-to-makefi.patch
+++ /dev/null
@@ -1,19 +0,0 @@
-From 07ccb18468b80890f8a251ab397e6f4bd96220a9 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Wed, 18 Nov 2015 20:26:03 +0000
-Subject: [PATCH] squash: add missing vc4-kms-v3d-overlay.dtb to makefile
-
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- 1 file changed, 1 insertion(+)
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -52,6 +52,7 @@ dtb-$(RPI_DT_OVERLAYS) += smi-overlay.dt
- dtb-$(RPI_DT_OVERLAYS) += spi-gpio35-39-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += tinylcd35-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += uart1-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += vc4-kms-v3d-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += vga666-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += w1-gpio-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += w1-gpio-pullup-overlay.dtb
diff --git a/target/linux/brcm2708/patches-4.4/0104-clk-bcm2835-Also-build-the-driver-for-downstream-ker.patch b/target/linux/brcm2708/patches-4.4/0104-clk-bcm2835-Also-build-the-driver-for-downstream-ker.patch
deleted file mode 100644
index c6a6acb..0000000
--- a/target/linux/brcm2708/patches-4.4/0104-clk-bcm2835-Also-build-the-driver-for-downstream-ker.patch
+++ /dev/null
@@ -1,21 +0,0 @@
-From 26c8fd640c3c381a19ebd6f04eea555bcf135b3d Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 12 Oct 2015 11:23:34 -0700
-Subject: [PATCH] clk: bcm2835: Also build the driver for downstream kernels.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/clk/bcm/Makefile | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/clk/bcm/Makefile
-+++ b/drivers/clk/bcm/Makefile
-@@ -3,7 +3,7 @@ obj-$(CONFIG_CLK_BCM_KONA) += clk-kona-s
- obj-$(CONFIG_CLK_BCM_KONA) += clk-bcm281xx.o
- obj-$(CONFIG_CLK_BCM_KONA) += clk-bcm21664.o
- obj-$(CONFIG_COMMON_CLK_IPROC) += clk-iproc-armpll.o clk-iproc-pll.o clk-iproc-asiu.o
--obj-$(CONFIG_ARCH_BCM2835) += clk-bcm2835.o
-+obj-$(CONFIG_ARCH_BCM2835)$(CONFIG_ARCH_BCM2708)$(CONFIG_ARCH_BCM2709) += clk-bcm2835.o
- obj-$(CONFIG_COMMON_CLK_IPROC) += clk-ns2.o
- obj-$(CONFIG_ARCH_BCM_CYGNUS) += clk-cygnus.o
- obj-$(CONFIG_ARCH_BCM_NSP) += clk-nsp.o
diff --git a/target/linux/brcm2708/patches-4.4/0105-dts-Added-overlay-for-gpio_ir_recv-driver.patch b/target/linux/brcm2708/patches-4.4/0105-dts-Added-overlay-for-gpio_ir_recv-driver.patch
deleted file mode 100644
index 829db7e..0000000
--- a/target/linux/brcm2708/patches-4.4/0105-dts-Added-overlay-for-gpio_ir_recv-driver.patch
+++ /dev/null
@@ -1,104 +0,0 @@
-From b88ba8c87060025b4e746bdf8c57ea0997a7aeaf Mon Sep 17 00:00:00 2001
-From: Holger Steinhaus <hsteinhaus at gmx.de>
-Date: Sat, 14 Nov 2015 18:37:43 +0100
-Subject: [PATCH] dts: Added overlay for gpio_ir_recv driver
-
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 18 ++++++++++-
- arch/arm/boot/dts/overlays/gpio-ir-overlay.dts | 45 ++++++++++++++++++++++++++
- 3 files changed, 63 insertions(+), 1 deletion(-)
- create mode 100644 arch/arm/boot/dts/overlays/gpio-ir-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -16,6 +16,7 @@ dtb-$(RPI_DT_OVERLAYS) += ads7846-overla
- dtb-$(RPI_DT_OVERLAYS) += bmp085_i2c-sensor-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += dht11-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += enc28j60-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += gpio-ir-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += gpio-poweroff-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += hifiberry-amp-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += hifiberry-dac-overlay.dtb
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -196,6 +196,22 @@ Params: int_pin GPIO us
- speed SPI bus speed (default 12000000)
-
-
-+Name: gpio-ir
-+Info: Use GPIO pin as rc-core style infrared receiver input. The rc-core-
-+ based gpio_ir_recv driver maps received keys directly to a
-+ /dev/input/event* device, all decoding is done by the kernel - LIRC is
-+ not required! The key mapping and other decoding parameters can be
-+ configured by "ir-keytable" tool.
-+Load: dtoverlay=gpio-ir,<param>=<val>
-+Params: gpio_pin Input pin number. Default is 18.
-+
-+ gpio_pull Desired pull-up/down state (off, down, up)
-+ Default is "down".
-+
-+ rc-map-name Default rc keymap (can also be changed by
-+ ir-keytable), defaults to "rc-rc6-mce"
-+
-+
- Name: gpio-poweroff
- Info: Drives a GPIO high or low on reboot
- Load: dtoverlay=gpio-poweroff,<param>=<val>
-@@ -308,7 +324,7 @@ Params: <None>
- Name: lirc-rpi
- Info: Configures lirc-rpi (Linux Infrared Remote Control for Raspberry Pi)
- Consult the module documentation for more details.
--Load: dtoverlay=lirc-rpi,<param>=<val>,...
-+Load: dtoverlay=lirc-rpi,<param>=<val>
- Params: gpio_out_pin GPIO for output (default "17")
-
- gpio_in_pin GPIO for input (default "18")
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/gpio-ir-overlay.dts
-@@ -0,0 +1,45 @@
-+// Definitions for ir-gpio module
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target-path = "/";
-+ __overlay__ {
-+ gpio_ir: ir-receiver {
-+ compatible = "gpio-ir-receiver";
-+
-+ // pin number, high or low
-+ gpios = <&gpio 18 1>;
-+
-+ // parameter for keymap name
-+ linux,rc-map-name = "rc-rc6-mce";
-+
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ gpio_ir_pins: gpio_ir_pins {
-+ brcm,pins = <18>; // pin 18
-+ brcm,function = <0>; // in
-+ brcm,pull = <1>; // down
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ // parameters
-+ gpio_pin = <&gpio_ir>,"gpios:4",
-+ <&gpio_ir_pins>,"brcm,pins:0",
-+ <&gpio_ir_pins>,"brcm,pull:0"; // pin number
-+ gpio_pull = <&gpio_ir_pins>,"brcm,pull:0"; // pull-up/down state
-+
-+ rc-map-name = <&gpio_ir>,"linux,rc-map-name"; // default rc map
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0106-Build-i2c_gpio-module-and-add-a-device-tree-overlay-.patch b/target/linux/brcm2708/patches-4.4/0106-Build-i2c_gpio-module-and-add-a-device-tree-overlay-.patch
deleted file mode 100644
index 2646892..0000000
--- a/target/linux/brcm2708/patches-4.4/0106-Build-i2c_gpio-module-and-add-a-device-tree-overlay-.patch
+++ /dev/null
@@ -1,100 +0,0 @@
-From 6ba415c6b0e804682ba7ae4477af9cbc56fb0776 Mon Sep 17 00:00:00 2001
-From: Alistair Buxton <a.j.buxton at gmail.com>
-Date: Sun, 1 Nov 2015 22:27:56 +0000
-Subject: [PATCH] Build i2c_gpio module and add a device tree overlay to
- configure it.
-
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 13 +++++++++++-
- arch/arm/boot/dts/overlays/i2c-gpio-overlay.dts | 28 +++++++++++++++++++++++++
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 5 files changed, 43 insertions(+), 1 deletion(-)
- create mode 100644 arch/arm/boot/dts/overlays/i2c-gpio-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -25,6 +25,7 @@ dtb-$(RPI_DT_OVERLAYS) += hifiberry-digi
- dtb-$(RPI_DT_OVERLAYS) += hy28a-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += hy28b-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += i2c-rtc-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += i2c-gpio-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += i2s-mmap-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += iqaudio-dac-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += iqaudio-dacplus-overlay.dtb
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -287,9 +287,20 @@ Params: speed Display
- ledgpio GPIO used to control backlight
-
-
-+Name: i2c-gpio
-+Info: Adds support for software i2c controller on gpio pins
-+Load: dtoverlay=i2c-gpio,<param>=<val>
-+Params: i2c_gpio_sda GPIO used for I2C data (default "23")
-+
-+ i2c_gpio_scl GPIO used for I2C clock (default "24")
-+
-+ i2c_gpio_delay_us Clock delay in microseconds
-+ (default "2" = ~100kHz)
-+
-+
- Name: i2c-rtc
- Info: Adds support for a number of I2C Real Time Clock devices
--Load: dtoverlay=i2c-rtc,<param>
-+Load: dtoverlay=i2c-rtc,<param>=<val>
- Params: ds1307 Select the DS1307 device
-
- ds3231 Select the DS3231 device
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/i2c-gpio-overlay.dts
-@@ -0,0 +1,28 @@
-+// Overlay for i2c_gpio bitbanging host bus.
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target-path = "/";
-+ __overlay__ {
-+ i2c_gpio: i2c at 0 {
-+ compatible = "i2c-gpio";
-+ gpios = <&gpio 23 0 /* sda */
-+ &gpio 24 0 /* scl */
-+ >;
-+ i2c-gpio,delay-us = <2>; /* ~100 kHz */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ };
-+ };
-+ };
-+ __overrides__ {
-+ i2c_gpio_sda = <&i2c_gpio>,"gpios:4";
-+ i2c_gpio_scl = <&i2c_gpio>,"gpios:16";
-+ i2c_gpio_delay_us = <&i2c_gpio>,"i2c-gpio,delay-us:0";
-+ };
-+};
-+
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -595,6 +595,7 @@ CONFIG_RAW_DRIVER=y
- CONFIG_I2C=y
- CONFIG_I2C_CHARDEV=m
- CONFIG_I2C_BCM2708=m
-+CONFIG_I2C_GPIO=m
- CONFIG_SPI=y
- CONFIG_SPI_BCM2835=m
- CONFIG_SPI_SPIDEV=y
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -588,6 +588,7 @@ CONFIG_RAW_DRIVER=y
- CONFIG_I2C=y
- CONFIG_I2C_CHARDEV=m
- CONFIG_I2C_BCM2708=m
-+CONFIG_I2C_GPIO=m
- CONFIG_SPI=y
- CONFIG_SPI_BCM2835=m
- CONFIG_SPI_SPIDEV=y
diff --git a/target/linux/brcm2708/patches-4.4/0107-New-overlay-for-PiScreen2r.patch b/target/linux/brcm2708/patches-4.4/0107-New-overlay-for-PiScreen2r.patch
deleted file mode 100644
index 0d763e7..0000000
--- a/target/linux/brcm2708/patches-4.4/0107-New-overlay-for-PiScreen2r.patch
+++ /dev/null
@@ -1,148 +0,0 @@
-From 6227748732f7620a4a2e1a4ea0727c69a894fc05 Mon Sep 17 00:00:00 2001
-From: mwilliams03 <mark.mwilliams at gmail.com>
-Date: Sun, 18 Oct 2015 17:07:24 -0700
-Subject: [PATCH] New overlay for PiScreen2r
-
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 14 +++
- arch/arm/boot/dts/overlays/piscreen2r-overlay.dts | 100 ++++++++++++++++++++++
- 3 files changed, 115 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/piscreen2r-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -35,6 +35,7 @@ dtb-$(RPI_DT_OVERLAYS) += mcp2515-can1-o
- dtb-$(RPI_DT_OVERLAYS) += mmc-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += mz61581-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += piscreen-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += piscreen2r-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += pitft28-resistive-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += pps-gpio-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += pwm-overlay.dtb
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -425,6 +425,20 @@ Params: speed Display
- xohms Touchpanel sensitivity (X-plate resistance)
-
-
-+Name: piscreen2r
-+Info: PiScreen 2 with resistive TP display by OzzMaker.com
-+Load: dtoverlay=piscreen2r,<param>=<val>
-+Params: speed Display SPI bus speed
-+
-+ rotate Display rotation {0,90,180,270}
-+
-+ fps Delay between frame updates
-+
-+ debug Debug output level {0-7}
-+
-+ xohms Touchpanel sensitivity (X-plate resistance)
-+
-+
- Name: pitft28-resistive
- Info: Adafruit PiTFT 2.8" resistive touch screen
- Load: dtoverlay=pitft28-resistive,<param>=<val>
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/piscreen2r-overlay.dts
-@@ -0,0 +1,100 @@
-+ /*
-+ * Device Tree overlay for PiScreen2 3.5" TFT with resistive touch by Ozzmaker.com
-+ *
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ status = "okay";
-+
-+ spidev at 0{
-+ status = "disabled";
-+ };
-+
-+ spidev at 1{
-+ status = "disabled";
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ piscreen2_pins: piscreen2_pins {
-+ brcm,pins = <17 25 24 22>;
-+ brcm,function = <0 1 1 1>; /* in out out out */
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ /* needed to avoid dtc warning */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ piscreen2: piscreen2 at 0{
-+ compatible = "ilitek,ili9486";
-+ reg = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&piscreen2_pins>;
-+ bgr;
-+ spi-max-frequency = <64000000>;
-+ rotate = <90>;
-+ fps = <30>;
-+ buswidth = <8>;
-+ regwidth = <16>;
-+ txbuflen = <32768>;
-+ reset-gpios = <&gpio 25 0>;
-+ dc-gpios = <&gpio 24 0>;
-+ led-gpios = <&gpio 22 1>;
-+ debug = <0>;
-+
-+ init = <0x10000b0 0x00
-+ 0x1000011
-+ 0x20000ff
-+ 0x100003a 0x55
-+ 0x1000036 0x28
-+ 0x10000c0 0x11 0x09
-+ 0x10000c1 0x41
-+ 0x10000c5 0x00 0x00 0x00 0x00
-+ 0x10000b6 0x00 0x02
-+ 0x10000f7 0xa9 0x51 0x2c 0x2
-+ 0x10000be 0x00 0x04
-+ 0x10000e9 0x00
-+ 0x1000011
-+ 0x1000029>;
-+
-+ };
-+
-+ piscreen2_ts: piscreen2-ts at 1 {
-+ compatible = "ti,ads7846";
-+ reg = <1>;
-+
-+ spi-max-frequency = <2000000>;
-+ interrupts = <17 2>; /* high-to-low edge triggered */
-+ interrupt-parent = <&gpio>;
-+ pendown-gpio = <&gpio 17 0>;
-+ ti,swap-xy;
-+ ti,x-plate-ohms = /bits/ 16 <100>;
-+ ti,pressure-max = /bits/ 16 <255>;
-+ };
-+ };
-+ };
-+ __overrides__ {
-+ speed = <&piscreen2>,"spi-max-frequency:0";
-+ rotate = <&piscreen2>,"rotate:0";
-+ fps = <&piscreen2>,"fps:0";
-+ debug = <&piscreen2>,"debug:0";
-+ xohms = <&piscreen2_ts>,"ti,x-plate-ohms;0";
-+ };
-+};
-+
diff --git a/target/linux/brcm2708/patches-4.4/0108-dts-Added-overlay-for-Adafruit-PiTFT-2.8-capacitive-.patch b/target/linux/brcm2708/patches-4.4/0108-dts-Added-overlay-for-Adafruit-PiTFT-2.8-capacitive-.patch
deleted file mode 100644
index a3139d0..0000000
--- a/target/linux/brcm2708/patches-4.4/0108-dts-Added-overlay-for-Adafruit-PiTFT-2.8-capacitive-.patch
+++ /dev/null
@@ -1,145 +0,0 @@
-From d1f148baae7c78dd81b5be8ada90a11c9634f926 Mon Sep 17 00:00:00 2001
-From: Ondrej Wisniewski <ondrej.wisniewski at gmail.com>
-Date: Fri, 6 Nov 2015 15:01:28 +0100
-Subject: [PATCH] dts: Added overlay for Adafruit PiTFT 2.8" capacitive touch
- screen
-
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 22 ++++++
- .../dts/overlays/pitft28-capacitive-overlay.dts | 88 ++++++++++++++++++++++
- 3 files changed, 111 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/pitft28-capacitive-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -36,6 +36,7 @@ dtb-$(RPI_DT_OVERLAYS) += mmc-overlay.dt
- dtb-$(RPI_DT_OVERLAYS) += mz61581-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += piscreen-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += piscreen2r-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += pitft28-capacitive-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += pitft28-resistive-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += pps-gpio-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += pwm-overlay.dtb
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -439,6 +439,28 @@ Params: speed Display
- xohms Touchpanel sensitivity (X-plate resistance)
-
-
-+Name: pitft28-capacitive
-+Info: Adafruit PiTFT 2.8" capacitive touch screen
-+Load: dtoverlay=pitft28-capacitive,<param>=<val>
-+Params: speed Display SPI bus speed
-+
-+ rotate Display rotation {0,90,180,270}
-+
-+ fps Delay between frame updates
-+
-+ debug Debug output level {0-7}
-+
-+ touch-sizex Touchscreen size x (default 240)
-+
-+ touch-sizey Touchscreen size y (default 320)
-+
-+ touch-invx Touchscreen inverted x axis
-+
-+ touch-invy Touchscreen inverted y axis
-+
-+ touch-swapxy Touchscreen swapped x y axis
-+
-+
- Name: pitft28-resistive
- Info: Adafruit PiTFT 2.8" resistive touch screen
- Load: dtoverlay=pitft28-resistive,<param>=<val>
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/pitft28-capacitive-overlay.dts
-@@ -0,0 +1,88 @@
-+/*
-+ * Device Tree overlay for Adafruit PiTFT 2.8" capacitive touch screen
-+ *
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ status = "okay";
-+
-+ spidev at 0{
-+ status = "disabled";
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ pitft_pins: pitft_pins {
-+ brcm,pins = <24 25>;
-+ brcm,function = <0 1>; /* in out */
-+ brcm,pull = <2 0>; /* pullup none */
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ /* needed to avoid dtc warning */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ pitft: pitft at 0{
-+ compatible = "ilitek,ili9340";
-+ reg = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pitft_pins>;
-+
-+ spi-max-frequency = <32000000>;
-+ rotate = <90>;
-+ fps = <25>;
-+ bgr;
-+ buswidth = <8>;
-+ dc-gpios = <&gpio 25 0>;
-+ debug = <0>;
-+ };
-+ };
-+ };
-+
-+ fragment at 3 {
-+ target = <&i2c1>;
-+ __overlay__ {
-+ /* needed to avoid dtc warning */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ ft6236: ft6236 at 38 {
-+ compatible = "focaltech,ft6236";
-+ reg = <0x38>;
-+
-+ interrupt-parent = <&gpio>;
-+ interrupts = <24 2>;
-+ touchscreen-size-x = <240>;
-+ touchscreen-size-y = <320>;
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ speed = <&pitft>,"spi-max-frequency:0";
-+ rotate = <&pitft>,"rotate:0";
-+ fps = <&pitft>,"fps:0";
-+ debug = <&pitft>,"debug:0";
-+ touch-sizex = <&ft6236>,"touchscreen-size-x?";
-+ touch-sizey = <&ft6236>,"touchscreen-size-y?";
-+ touch-invx = <&ft6236>,"touchscreen-inverted-x?";
-+ touch-invy = <&ft6236>,"touchscreen-inverted-y?";
-+ touch-swapxy = <&ft6236>,"touchscreen-swapped-x-y?";
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0109-Add-support-for-the-HiFiBerry-DAC-Pro.patch b/target/linux/brcm2708/patches-4.4/0109-Add-support-for-the-HiFiBerry-DAC-Pro.patch
deleted file mode 100644
index d688b26..0000000
--- a/target/linux/brcm2708/patches-4.4/0109-Add-support-for-the-HiFiBerry-DAC-Pro.patch
+++ /dev/null
@@ -1,539 +0,0 @@
-From f1ca0131a9b30284a9d6b763f2e2498bd29e2340 Mon Sep 17 00:00:00 2001
-From: Stuart MacLean <stuart at hifiberry.com>
-Date: Fri, 2 Oct 2015 15:12:59 +0100
-Subject: [PATCH] Add support for the HiFiBerry DAC+ Pro.
-
-The HiFiBerry DAC+ and DAC+ Pro products both use the existing bcm sound driver with the DAC+ Pro having a special clock device driver representing the two high precision oscillators.
-
-An addition bug fix is included for the PCM512x codec where by the physical size of the sample frame is used in the calculation of the LRCK divisor as it was found to be wrong when using 24-bit depth sample contained in a little endian 4-byte sample frame.
----
- .../dts/overlays/hifiberry-dacplus-overlay.dts | 15 +-
- drivers/clk/Makefile | 1 +
- drivers/clk/clk-hifiberry-dacpro.c | 160 ++++++++++++++
- sound/soc/bcm/hifiberry_dacplus.c | 244 +++++++++++++++++++--
- sound/soc/codecs/pcm512x.c | 3 +-
- 5 files changed, 396 insertions(+), 27 deletions(-)
- create mode 100644 drivers/clk/clk-hifiberry-dacpro.c
-
---- a/arch/arm/boot/dts/overlays/hifiberry-dacplus-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/hifiberry-dacplus-overlay.dts
-@@ -6,6 +6,16 @@
- compatible = "brcm,bcm2708";
-
- fragment at 0 {
-+ target-path = "/clocks";
-+ __overlay__ {
-+ dacpro_osc: dacpro_osc {
-+ compatible = "hifiberry,dacpro-clk";
-+ #clock-cells = <0>;
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
- target = <&sound>;
- __overlay__ {
- compatible = "hifiberry,hifiberry-dacplus";
-@@ -14,14 +24,14 @@
- };
- };
-
-- fragment at 1 {
-+ fragment at 2 {
- target = <&i2s>;
- __overlay__ {
- status = "okay";
- };
- };
-
-- fragment at 2 {
-+ fragment at 3 {
- target = <&i2c1>;
- __overlay__ {
- #address-cells = <1>;
-@@ -32,6 +42,7 @@
- #sound-dai-cells = <0>;
- compatible = "ti,pcm5122";
- reg = <0x4d>;
-+ clocks = <&dacpro_osc>;
- status = "okay";
- };
- };
---- a/drivers/clk/Makefile
-+++ b/drivers/clk/Makefile
-@@ -24,6 +24,7 @@ obj-$(CONFIG_COMMON_CLK_CDCE706) += clk-
- obj-$(CONFIG_ARCH_CLPS711X) += clk-clps711x.o
- obj-$(CONFIG_ARCH_EFM32) += clk-efm32gg.o
- obj-$(CONFIG_ARCH_HIGHBANK) += clk-highbank.o
-+obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DACPLUS) += clk-hifiberry-dacpro.o
- obj-$(CONFIG_MACH_LOONGSON32) += clk-ls1x.o
- obj-$(CONFIG_COMMON_CLK_MAX_GEN) += clk-max-gen.o
- obj-$(CONFIG_COMMON_CLK_MAX77686) += clk-max77686.o
---- /dev/null
-+++ b/drivers/clk/clk-hifiberry-dacpro.c
-@@ -0,0 +1,160 @@
-+/*
-+ * Clock Driver for HiFiBerry DAC Pro
-+ *
-+ * Author: Stuart MacLean
-+ * Copyright 2015
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * version 2 as published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful, but
-+ * WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
-+ * General Public License for more details.
-+ */
-+
-+#include <linux/clk-provider.h>
-+#include <linux/clkdev.h>
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+#include <linux/of.h>
-+#include <linux/slab.h>
-+#include <linux/platform_device.h>
-+
-+/* Clock rate of CLK44EN attached to GPIO6 pin */
-+#define CLK_44EN_RATE 22579200UL
-+/* Clock rate of CLK48EN attached to GPIO3 pin */
-+#define CLK_48EN_RATE 24576000UL
-+
-+/**
-+ * struct hifiberry_dacpro_clk - Common struct to the HiFiBerry DAC Pro
-+ * @hw: clk_hw for the common clk framework
-+ * @mode: 0 => CLK44EN, 1 => CLK48EN
-+ */
-+struct clk_hifiberry_hw {
-+ struct clk_hw hw;
-+ uint8_t mode;
-+};
-+
-+#define to_hifiberry_clk(_hw) container_of(_hw, struct clk_hifiberry_hw, hw)
-+
-+static const struct of_device_id clk_hifiberry_dacpro_dt_ids[] = {
-+ { .compatible = "hifiberry,dacpro-clk",},
-+ { }
-+};
-+MODULE_DEVICE_TABLE(of, clk_hifiberry_dacpro_dt_ids);
-+
-+static unsigned long clk_hifiberry_dacpro_recalc_rate(struct clk_hw *hw,
-+ unsigned long parent_rate)
-+{
-+ return (to_hifiberry_clk(hw)->mode == 0) ? CLK_44EN_RATE :
-+ CLK_48EN_RATE;
-+}
-+
-+static long clk_hifiberry_dacpro_round_rate(struct clk_hw *hw,
-+ unsigned long rate, unsigned long *parent_rate)
-+{
-+ long actual_rate;
-+
-+ if (rate <= CLK_44EN_RATE) {
-+ actual_rate = (long)CLK_44EN_RATE;
-+ } else if (rate >= CLK_48EN_RATE) {
-+ actual_rate = (long)CLK_48EN_RATE;
-+ } else {
-+ long diff44Rate = (long)(rate - CLK_44EN_RATE);
-+ long diff48Rate = (long)(CLK_48EN_RATE - rate);
-+
-+ if (diff44Rate < diff48Rate)
-+ actual_rate = (long)CLK_44EN_RATE;
-+ else
-+ actual_rate = (long)CLK_48EN_RATE;
-+ }
-+ return actual_rate;
-+}
-+
-+
-+static int clk_hifiberry_dacpro_set_rate(struct clk_hw *hw,
-+ unsigned long rate, unsigned long parent_rate)
-+{
-+ unsigned long actual_rate;
-+ struct clk_hifiberry_hw *clk = to_hifiberry_clk(hw);
-+
-+ actual_rate = (unsigned long)clk_hifiberry_dacpro_round_rate(hw, rate,
-+ &parent_rate);
-+ clk->mode = (actual_rate == CLK_44EN_RATE) ? 0 : 1;
-+ return 0;
-+}
-+
-+
-+const struct clk_ops clk_hifiberry_dacpro_rate_ops = {
-+ .recalc_rate = clk_hifiberry_dacpro_recalc_rate,
-+ .round_rate = clk_hifiberry_dacpro_round_rate,
-+ .set_rate = clk_hifiberry_dacpro_set_rate,
-+};
-+
-+static int clk_hifiberry_dacpro_probe(struct platform_device *pdev)
-+{
-+ int ret;
-+ struct clk_hifiberry_hw *proclk;
-+ struct clk *clk;
-+ struct device *dev;
-+ struct clk_init_data init;
-+
-+ dev = &pdev->dev;
-+
-+ proclk = kzalloc(sizeof(struct clk_hifiberry_hw), GFP_KERNEL);
-+ if (!proclk)
-+ return -ENOMEM;
-+
-+ init.name = "clk-hifiberry-dacpro";
-+ init.ops = &clk_hifiberry_dacpro_rate_ops;
-+ init.flags = CLK_IS_ROOT | CLK_IS_BASIC;
-+ init.parent_names = NULL;
-+ init.num_parents = 0;
-+
-+ proclk->mode = 0;
-+ proclk->hw.init = &init;
-+
-+ clk = devm_clk_register(dev, &proclk->hw);
-+ if (!IS_ERR(clk)) {
-+ ret = of_clk_add_provider(dev->of_node, of_clk_src_simple_get,
-+ clk);
-+ } else {
-+ dev_err(dev, "Fail to register clock driver\n");
-+ kfree(proclk);
-+ ret = PTR_ERR(clk);
-+ }
-+ return ret;
-+}
-+
-+static int clk_hifiberry_dacpro_remove(struct platform_device *pdev)
-+{
-+ of_clk_del_provider(pdev->dev.of_node);
-+ return 0;
-+}
-+
-+static struct platform_driver clk_hifiberry_dacpro_driver = {
-+ .probe = clk_hifiberry_dacpro_probe,
-+ .remove = clk_hifiberry_dacpro_remove,
-+ .driver = {
-+ .name = "clk-hifiberry-dacpro",
-+ .of_match_table = clk_hifiberry_dacpro_dt_ids,
-+ },
-+};
-+
-+static int __init clk_hifiberry_dacpro_init(void)
-+{
-+ return platform_driver_register(&clk_hifiberry_dacpro_driver);
-+}
-+core_initcall(clk_hifiberry_dacpro_init);
-+
-+static void __exit clk_hifiberry_dacpro_exit(void)
-+{
-+ platform_driver_unregister(&clk_hifiberry_dacpro_driver);
-+}
-+module_exit(clk_hifiberry_dacpro_exit);
-+
-+MODULE_DESCRIPTION("HiFiBerry DAC Pro clock driver");
-+MODULE_LICENSE("GPL v2");
-+MODULE_ALIAS("platform:clk-hifiberry-dacpro");
---- a/sound/soc/bcm/hifiberry_dacplus.c
-+++ b/sound/soc/bcm/hifiberry_dacplus.c
-@@ -1,8 +1,8 @@
- /*
-- * ASoC Driver for HiFiBerry DAC+
-+ * ASoC Driver for HiFiBerry DAC+ / DAC Pro
- *
-- * Author: Daniel Matuschek
-- * Copyright 2014
-+ * Author: Daniel Matuschek, Stuart MacLean <stuart at hifiberry.com>
-+ * Copyright 2014-2015
- * based on code by Florian Meier <florian.meier at koalo.de>
- *
- * This program is free software; you can redistribute it and/or
-@@ -17,6 +17,13 @@
-
- #include <linux/module.h>
- #include <linux/platform_device.h>
-+#include <linux/kernel.h>
-+#include <linux/clk.h>
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+#include <linux/of.h>
-+#include <linux/slab.h>
-+#include <linux/delay.h>
-
- #include <sound/core.h>
- #include <sound/pcm.h>
-@@ -26,34 +33,222 @@
-
- #include "../codecs/pcm512x.h"
-
-+#define HIFIBERRY_DACPRO_NOCLOCK 0
-+#define HIFIBERRY_DACPRO_CLK44EN 1
-+#define HIFIBERRY_DACPRO_CLK48EN 2
-+
-+struct pcm512x_priv {
-+ struct regmap *regmap;
-+ struct clk *sclk;
-+};
-+
-+/* Clock rate of CLK44EN attached to GPIO6 pin */
-+#define CLK_44EN_RATE 22579200UL
-+/* Clock rate of CLK48EN attached to GPIO3 pin */
-+#define CLK_48EN_RATE 24576000UL
-+
-+static bool snd_rpi_hifiberry_is_dacpro;
-+
-+static void snd_rpi_hifiberry_dacplus_select_clk(struct snd_soc_codec *codec,
-+ int clk_id)
-+{
-+ switch (clk_id) {
-+ case HIFIBERRY_DACPRO_NOCLOCK:
-+ snd_soc_update_bits(codec, PCM512x_GPIO_CONTROL_1, 0x24, 0x00);
-+ break;
-+ case HIFIBERRY_DACPRO_CLK44EN:
-+ snd_soc_update_bits(codec, PCM512x_GPIO_CONTROL_1, 0x24, 0x20);
-+ break;
-+ case HIFIBERRY_DACPRO_CLK48EN:
-+ snd_soc_update_bits(codec, PCM512x_GPIO_CONTROL_1, 0x24, 0x04);
-+ break;
-+ }
-+}
-+
-+static void snd_rpi_hifiberry_dacplus_clk_gpio(struct snd_soc_codec *codec)
-+{
-+ snd_soc_update_bits(codec, PCM512x_GPIO_EN, 0x24, 0x24);
-+ snd_soc_update_bits(codec, PCM512x_GPIO_OUTPUT_3, 0x0f, 0x02);
-+ snd_soc_update_bits(codec, PCM512x_GPIO_OUTPUT_6, 0x0f, 0x02);
-+}
-+
-+static bool snd_rpi_hifiberry_dacplus_is_sclk(struct snd_soc_codec *codec)
-+{
-+ int sck;
-+
-+ sck = snd_soc_read(codec, PCM512x_RATE_DET_4);
-+ return (!(sck & 0x40));
-+}
-+
-+static bool snd_rpi_hifiberry_dacplus_is_sclk_sleep(
-+ struct snd_soc_codec *codec)
-+{
-+ msleep(2);
-+ return snd_rpi_hifiberry_dacplus_is_sclk(codec);
-+}
-+
-+static bool snd_rpi_hifiberry_dacplus_is_pro_card(struct snd_soc_codec *codec)
-+{
-+ bool isClk44EN, isClk48En, isNoClk;
-+
-+ snd_rpi_hifiberry_dacplus_clk_gpio(codec);
-+
-+ snd_rpi_hifiberry_dacplus_select_clk(codec, HIFIBERRY_DACPRO_CLK44EN);
-+ isClk44EN = snd_rpi_hifiberry_dacplus_is_sclk_sleep(codec);
-+
-+ snd_rpi_hifiberry_dacplus_select_clk(codec, HIFIBERRY_DACPRO_NOCLOCK);
-+ isNoClk = snd_rpi_hifiberry_dacplus_is_sclk_sleep(codec);
-+
-+ snd_rpi_hifiberry_dacplus_select_clk(codec, HIFIBERRY_DACPRO_CLK48EN);
-+ isClk48En = snd_rpi_hifiberry_dacplus_is_sclk_sleep(codec);
-+
-+ return (isClk44EN && isClk48En && !isNoClk);
-+}
-+
-+static int snd_rpi_hifiberry_dacplus_clk_for_rate(int sample_rate)
-+{
-+ int type;
-+
-+ switch (sample_rate) {
-+ case 11025:
-+ case 22050:
-+ case 44100:
-+ case 88200:
-+ case 176400:
-+ type = HIFIBERRY_DACPRO_CLK44EN;
-+ break;
-+ default:
-+ type = HIFIBERRY_DACPRO_CLK48EN;
-+ break;
-+ }
-+ return type;
-+}
-+
-+static void snd_rpi_hifiberry_dacplus_set_sclk(struct snd_soc_codec *codec,
-+ int sample_rate)
-+{
-+ struct pcm512x_priv *pcm512x = snd_soc_codec_get_drvdata(codec);
-+
-+ if (!IS_ERR(pcm512x->sclk)) {
-+ int ctype;
-+
-+ ctype = snd_rpi_hifiberry_dacplus_clk_for_rate(sample_rate);
-+ clk_set_rate(pcm512x->sclk, (ctype == HIFIBERRY_DACPRO_CLK44EN)
-+ ? CLK_44EN_RATE : CLK_48EN_RATE);
-+ snd_rpi_hifiberry_dacplus_select_clk(codec, ctype);
-+ }
-+}
-+
- static int snd_rpi_hifiberry_dacplus_init(struct snd_soc_pcm_runtime *rtd)
- {
- struct snd_soc_codec *codec = rtd->codec;
-+ struct pcm512x_priv *priv;
-+
-+ snd_rpi_hifiberry_is_dacpro
-+ = snd_rpi_hifiberry_dacplus_is_pro_card(codec);
-+
-+ if (snd_rpi_hifiberry_is_dacpro) {
-+ struct snd_soc_dai_link *dai = rtd->dai_link;
-+
-+ dai->name = "HiFiBerry DAC+ Pro";
-+ dai->stream_name = "HiFiBerry DAC+ Pro HiFi";
-+ dai->dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF
-+ | SND_SOC_DAIFMT_CBM_CFM;
-+
-+ snd_soc_update_bits(codec, PCM512x_BCLK_LRCLK_CFG, 0x31, 0x11);
-+ snd_soc_update_bits(codec, PCM512x_MASTER_MODE, 0x03, 0x03);
-+ snd_soc_update_bits(codec, PCM512x_MASTER_CLKDIV_2, 0x7f, 63);
-+ } else {
-+ priv = snd_soc_codec_get_drvdata(codec);
-+ priv->sclk = ERR_PTR(-ENOENT);
-+ }
-+
- snd_soc_update_bits(codec, PCM512x_GPIO_EN, 0x08, 0x08);
-- snd_soc_update_bits(codec, PCM512x_GPIO_OUTPUT_4, 0xf, 0x02);
-- snd_soc_update_bits(codec, PCM512x_GPIO_CONTROL_1, 0x08,0x08);
-+ snd_soc_update_bits(codec, PCM512x_GPIO_OUTPUT_4, 0x0f, 0x02);
-+ snd_soc_update_bits(codec, PCM512x_GPIO_CONTROL_1, 0x08, 0x08);
-+
-+ return 0;
-+}
-+
-+static int snd_rpi_hifiberry_dacplus_update_rate_den(
-+ struct snd_pcm_substream *substream, struct snd_pcm_hw_params *params)
-+{
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_codec *codec = rtd->codec;
-+ struct pcm512x_priv *pcm512x = snd_soc_codec_get_drvdata(codec);
-+ struct snd_ratnum *rats_no_pll;
-+ unsigned int num = 0, den = 0;
-+ int err;
-+
-+ rats_no_pll = devm_kzalloc(rtd->dev, sizeof(*rats_no_pll), GFP_KERNEL);
-+ if (!rats_no_pll)
-+ return -ENOMEM;
-+
-+ rats_no_pll->num = clk_get_rate(pcm512x->sclk) / 64;
-+ rats_no_pll->den_min = 1;
-+ rats_no_pll->den_max = 128;
-+ rats_no_pll->den_step = 1;
-+
-+ err = snd_interval_ratnum(hw_param_interval(params,
-+ SNDRV_PCM_HW_PARAM_RATE), 1, rats_no_pll, &num, &den);
-+ if (err >= 0 && den) {
-+ params->rate_num = num;
-+ params->rate_den = den;
-+ }
-+
-+ devm_kfree(rtd->dev, rats_no_pll);
- return 0;
- }
-
--static int snd_rpi_hifiberry_dacplus_hw_params(struct snd_pcm_substream *substream,
-- struct snd_pcm_hw_params *params)
-+static int snd_rpi_hifiberry_dacplus_set_bclk_ratio_pro(
-+ struct snd_soc_dai *cpu_dai, struct snd_pcm_hw_params *params)
-+{
-+ int bratio = snd_pcm_format_physical_width(params_format(params))
-+ * params_channels(params);
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, bratio);
-+}
-+
-+static int snd_rpi_hifiberry_dacplus_hw_params(
-+ struct snd_pcm_substream *substream, struct snd_pcm_hw_params *params)
- {
-+ int ret;
- struct snd_soc_pcm_runtime *rtd = substream->private_data;
- struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
-- return snd_soc_dai_set_bclk_ratio(cpu_dai, 64);
-+
-+ if (snd_rpi_hifiberry_is_dacpro) {
-+ struct snd_soc_codec *codec = rtd->codec;
-+
-+ snd_rpi_hifiberry_dacplus_set_sclk(codec,
-+ params_rate(params));
-+
-+ ret = snd_rpi_hifiberry_dacplus_set_bclk_ratio_pro(cpu_dai,
-+ params);
-+ if (!ret)
-+ ret = snd_rpi_hifiberry_dacplus_update_rate_den(
-+ substream, params);
-+ } else {
-+ ret = snd_soc_dai_set_bclk_ratio(cpu_dai, 64);
-+ }
-+ return ret;
- }
-
--static int snd_rpi_hifiberry_dacplus_startup(struct snd_pcm_substream *substream) {
-+static int snd_rpi_hifiberry_dacplus_startup(
-+ struct snd_pcm_substream *substream)
-+{
- struct snd_soc_pcm_runtime *rtd = substream->private_data;
- struct snd_soc_codec *codec = rtd->codec;
-- snd_soc_update_bits(codec, PCM512x_GPIO_CONTROL_1, 0x08,0x08);
-+
-+ snd_soc_update_bits(codec, PCM512x_GPIO_CONTROL_1, 0x08, 0x08);
- return 0;
- }
-
--static void snd_rpi_hifiberry_dacplus_shutdown(struct snd_pcm_substream *substream) {
-+static void snd_rpi_hifiberry_dacplus_shutdown(
-+ struct snd_pcm_substream *substream)
-+{
- struct snd_soc_pcm_runtime *rtd = substream->private_data;
- struct snd_soc_codec *codec = rtd->codec;
-- snd_soc_update_bits(codec, PCM512x_GPIO_CONTROL_1, 0x08,0x00);
-+
-+ snd_soc_update_bits(codec, PCM512x_GPIO_CONTROL_1, 0x08, 0x00);
- }
-
- /* machine stream operations */
-@@ -90,19 +285,20 @@ static int snd_rpi_hifiberry_dacplus_pro
- int ret = 0;
-
- snd_rpi_hifiberry_dacplus.dev = &pdev->dev;
--
- if (pdev->dev.of_node) {
-- struct device_node *i2s_node;
-- struct snd_soc_dai_link *dai = &snd_rpi_hifiberry_dacplus_dai[0];
-- i2s_node = of_parse_phandle(pdev->dev.of_node,
-- "i2s-controller", 0);
--
-- if (i2s_node) {
-- dai->cpu_dai_name = NULL;
-- dai->cpu_of_node = i2s_node;
-- dai->platform_name = NULL;
-- dai->platform_of_node = i2s_node;
-- }
-+ struct device_node *i2s_node;
-+ struct snd_soc_dai_link *dai;
-+
-+ dai = &snd_rpi_hifiberry_dacplus_dai[0];
-+ i2s_node = of_parse_phandle(pdev->dev.of_node,
-+ "i2s-controller", 0);
-+
-+ if (i2s_node) {
-+ dai->cpu_dai_name = NULL;
-+ dai->cpu_of_node = i2s_node;
-+ dai->platform_name = NULL;
-+ dai->platform_of_node = i2s_node;
-+ }
- }
-
- ret = snd_soc_register_card(&snd_rpi_hifiberry_dacplus);
---- a/sound/soc/codecs/pcm512x.c
-+++ b/sound/soc/codecs/pcm512x.c
-@@ -854,7 +854,8 @@ static int pcm512x_set_dividers(struct s
- int fssp;
- int gpio;
-
-- lrclk_div = snd_soc_params_to_frame_size(params);
-+ lrclk_div = snd_pcm_format_physical_width(params_format(params))
-+ * params_channels(params);
- if (lrclk_div == 0) {
- dev_err(dev, "No LRCLK?\n");
- return -EINVAL;
diff --git a/target/linux/brcm2708/patches-4.4/0110-BCM270X_DT-Add-at86rf233-overlay.patch b/target/linux/brcm2708/patches-4.4/0110-BCM270X_DT-Add-at86rf233-overlay.patch
deleted file mode 100644
index 24ca257..0000000
--- a/target/linux/brcm2708/patches-4.4/0110-BCM270X_DT-Add-at86rf233-overlay.patch
+++ /dev/null
@@ -1,130 +0,0 @@
-From 55fb7544e8e08b709140847810b2c7fa1efbb76d Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 5 Oct 2015 10:47:45 +0100
-Subject: [PATCH] BCM270X_DT: Add at86rf233 overlay
-
-Add an overlay to support the Atmel AT86RF233 WPAN transceiver on spi0.0.
-
-See: https://github.com/raspberrypi/linux/issues/1151
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 21 +++++++--
- arch/arm/boot/dts/overlays/at86rf233-overlay.dts | 54 ++++++++++++++++++++++++
- 3 files changed, 72 insertions(+), 4 deletions(-)
- create mode 100644 arch/arm/boot/dts/overlays/at86rf233-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -13,6 +13,7 @@ ifeq ($(CONFIG_ARCH_BCM2835),y)
- endif
-
- dtb-$(RPI_DT_OVERLAYS) += ads7846-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += at86rf233-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += bmp085_i2c-sensor-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += dht11-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += enc28j60-overlay.dtb
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -69,13 +69,14 @@ DT parameters:
-
- Parameters always have default values, although in some cases (e.g. "w1-gpio")
- it is necessary to provided multiple overlays in order to get the desired
--behaviour. See the list of overlays below for a description of the parameters and their defaults.
-+behaviour. See the list of overlays below for a description of the parameters
-+and their defaults.
-
- The Overlay and Parameter Reference
- ===================================
-
--N.B. When editing this file, please preserve the indentation levels to make it simple to parse
--programmatically. NO HARD TABS.
-+N.B. When editing this file, please preserve the indentation levels to make it
-+simple to parse programmatically. NO HARD TABS.
-
-
- Name: <The base DTB>
-@@ -149,7 +150,7 @@ Name: ads7846
- Info: ADS7846 Touch controller
- Load: dtoverlay=ads7846,<param>=<val>
- Params: cs SPI bus Chip Select (default 1)
-- speed SPI bus speed (default 2Mhz, max 3.25MHz)
-+ speed SPI bus speed (default 2MHz, max 3.25MHz)
- penirq GPIO used for PENIRQ. REQUIRED
- penirq_pull Set GPIO pull (default 0=none, 2=pullup)
- swapxy Swap x and y axis
-@@ -170,6 +171,18 @@ Params: cs SPI bus
- www.kernel.org/doc/Documentation/devicetree/bindings/input/ads7846.txt
-
-
-+Name: at86rf233
-+Info: Configures the Atmel AT86RF233 802.15.4 low-power WPAN transceiver,
-+ connected to spi0.0
-+Load: dtoverlay=at86rf233,<param>=<val>
-+Params: interrupt GPIO used for INT (default 23)
-+ reset GPIO used for Reset (default 24)
-+ sleep GPIO used for Sleep (default 25)
-+ speed SPI bus speed in Hz (default 6000000)
-+ trim Fine tuning of the internal capacitance
-+ arrays (0=+0pF, 15=+4.5pF, default 15)
-+
-+
- Name: bmp085_i2c-sensor
- Info: Configures the BMP085/BMP180 digital barometric pressure and temperature
- sensors from Bosch Sensortec
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/at86rf233-overlay.dts
-@@ -0,0 +1,54 @@
-+/dts-v1/;
-+/plugin/;
-+
-+/* Overlay for Atmel AT86RF233 IEEE 802.15.4 WPAN transceiver on spi0.0 */
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2836", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ status = "okay";
-+
-+ spidev at 0{
-+ status = "disabled";
-+ };
-+
-+ lowpan0: at86rf233 at 0 {
-+ compatible = "atmel,at86rf233";
-+ reg = <0>;
-+ interrupt-parent = <&gpio>;
-+ interrupts = <23 4>; /* active high */
-+ reset-gpio = <&gpio 24 1>;
-+ sleep-gpio = <&gpio 25 1>;
-+ spi-max-frequency = <6000000>;
-+ xtal-trim = /bits/ 8 <0xf>;
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ lowpan0_pins: lowpan0_pins {
-+ brcm,pins = <23 24 25>;
-+ brcm,function = <0 1 1>; /* in out out */
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ interrupt = <&lowpan0>, "interrupts:0",
-+ <&lowpan0_pins>, "brcm,pins:0";
-+ reset = <&lowpan0>, "reset-gpio:4",
-+ <&lowpan0_pins>, "brcm,pins:4";
-+ sleep = <&lowpan0>, "sleep-gpio:4",
-+ <&lowpan0_pins>, "brcm,pins:8";
-+ speed = <&lowpan0>, "spi-max-frequency:0";
-+ trim = <&lowpan0>, "xtal-trim.0";
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0111-mm-Remove-the-PFN-busy-warning.patch b/target/linux/brcm2708/patches-4.4/0111-mm-Remove-the-PFN-busy-warning.patch
deleted file mode 100644
index 304ec97..0000000
--- a/target/linux/brcm2708/patches-4.4/0111-mm-Remove-the-PFN-busy-warning.patch
+++ /dev/null
@@ -1,25 +0,0 @@
-From b057a14e7ce825cb0f21a56c6f255878e71679f1 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Thu, 18 Dec 2014 16:07:15 -0800
-Subject: [PATCH] mm: Remove the PFN busy warning
-
-See commit dae803e165a11bc88ca8dbc07a11077caf97bbcb -- the warning is
-expected sometimes when using CMA. However, that commit still spams
-my kernel log with these warnings.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- mm/page_alloc.c | 2 --
- 1 file changed, 2 deletions(-)
-
---- a/mm/page_alloc.c
-+++ b/mm/page_alloc.c
-@@ -6785,8 +6785,6 @@ int alloc_contig_range(unsigned long sta
-
- /* Make sure the range is really isolated. */
- if (test_pages_isolated(outer_start, end, false)) {
-- pr_info("%s: [%lx, %lx) PFNs busy\n",
-- __func__, outer_start, end);
- ret = -EBUSY;
- goto done;
- }
diff --git a/target/linux/brcm2708/patches-4.4/0112-drm-Put-an-optional-field-in-the-driver-struct-for-G.patch b/target/linux/brcm2708/patches-4.4/0112-drm-Put-an-optional-field-in-the-driver-struct-for-G.patch
deleted file mode 100644
index 1dbdbed..0000000
--- a/target/linux/brcm2708/patches-4.4/0112-drm-Put-an-optional-field-in-the-driver-struct-for-G.patch
+++ /dev/null
@@ -1,40 +0,0 @@
-From 00d855eeb84f87ee69745204c237ef97970e7b14 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Wed, 19 Nov 2014 12:06:38 -0800
-Subject: [PATCH] drm: Put an optional field in the driver struct for GEM obj
- struct size.
-
-This allows a driver to derive from the CMA object without copying all
-of the code.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/drm_gem_cma_helper.c | 5 ++++-
- include/drm/drmP.h | 1 +
- 2 files changed, 5 insertions(+), 1 deletion(-)
-
---- a/drivers/gpu/drm/drm_gem_cma_helper.c
-+++ b/drivers/gpu/drm/drm_gem_cma_helper.c
-@@ -58,8 +58,11 @@ __drm_gem_cma_create(struct drm_device *
- struct drm_gem_cma_object *cma_obj;
- struct drm_gem_object *gem_obj;
- int ret;
-+ size_t obj_size = (drm->driver->gem_obj_size ?
-+ drm->driver->gem_obj_size :
-+ sizeof(*cma_obj));
-
-- cma_obj = kzalloc(sizeof(*cma_obj), GFP_KERNEL);
-+ cma_obj = kzalloc(obj_size, GFP_KERNEL);
- if (!cma_obj)
- return ERR_PTR(-ENOMEM);
-
---- a/include/drm/drmP.h
-+++ b/include/drm/drmP.h
-@@ -639,6 +639,7 @@ struct drm_driver {
-
- u32 driver_features;
- int dev_priv_size;
-+ size_t gem_obj_size;
- const struct drm_ioctl_desc *ioctls;
- int num_ioctls;
- const struct file_operations *fops;
diff --git a/target/linux/brcm2708/patches-4.4/0113-drm-vc4-Add-an-interface-for-capturing-the-GPU-state.patch b/target/linux/brcm2708/patches-4.4/0113-drm-vc4-Add-an-interface-for-capturing-the-GPU-state.patch
deleted file mode 100644
index f18d29a..0000000
--- a/target/linux/brcm2708/patches-4.4/0113-drm-vc4-Add-an-interface-for-capturing-the-GPU-state.patch
+++ /dev/null
@@ -1,333 +0,0 @@
-From ad2ad9247674a383ed7ca1c5e762b60625b146ec Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 30 Oct 2015 10:09:02 -0700
-Subject: [PATCH] drm/vc4: Add an interface for capturing the GPU state after a
- hang.
-
-This can be parsed with vc4-gpu-tools tools for trying to figure out
-what was going on.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_bo.c | 4 +-
- drivers/gpu/drm/vc4/vc4_drv.c | 1 +
- drivers/gpu/drm/vc4/vc4_drv.h | 4 +
- drivers/gpu/drm/vc4/vc4_gem.c | 185 ++++++++++++++++++++++++++++++++++++++++++
- include/uapi/drm/vc4_drm.h | 45 ++++++++++
- 5 files changed, 237 insertions(+), 2 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_bo.c
-+++ b/drivers/gpu/drm/vc4/vc4_bo.c
-@@ -415,8 +415,8 @@ int vc4_mmap(struct file *filp, struct v
- gem_obj = vma->vm_private_data;
- bo = to_vc4_bo(gem_obj);
-
-- if (bo->validated_shader) {
-- DRM_ERROR("mmaping of shader BOs not allowed.\n");
-+ if (bo->validated_shader && (vma->vm_flags & VM_WRITE)) {
-+ DRM_ERROR("mmaping of shader BOs for writing not allowed.\n");
- return -EINVAL;
- }
-
---- a/drivers/gpu/drm/vc4/vc4_drv.c
-+++ b/drivers/gpu/drm/vc4/vc4_drv.c
-@@ -81,6 +81,7 @@ static const struct drm_ioctl_desc vc4_d
- DRM_IOCTL_DEF_DRV(VC4_CREATE_BO, vc4_create_bo_ioctl, 0),
- DRM_IOCTL_DEF_DRV(VC4_MMAP_BO, vc4_mmap_bo_ioctl, 0),
- DRM_IOCTL_DEF_DRV(VC4_CREATE_SHADER_BO, vc4_create_shader_bo_ioctl, 0),
-+ DRM_IOCTL_DEF_DRV(VC4_GET_HANG_STATE, vc4_get_hang_state_ioctl, DRM_ROOT_ONLY),
- };
-
- static struct drm_driver vc4_drm_driver = {
---- a/drivers/gpu/drm/vc4/vc4_drv.h
-+++ b/drivers/gpu/drm/vc4/vc4_drv.h
-@@ -20,6 +20,8 @@ struct vc4_dev {
- struct drm_fbdev_cma *fbdev;
- struct rpi_firmware *firmware;
-
-+ struct vc4_hang_state *hang_state;
-+
- /* The kernel-space BO cache. Tracks buffers that have been
- * unreferenced by all other users (refcounts of 0!) but not
- * yet freed, so we can do cheap allocations.
-@@ -366,6 +368,8 @@ int vc4_create_shader_bo_ioctl(struct dr
- struct drm_file *file_priv);
- int vc4_mmap_bo_ioctl(struct drm_device *dev, void *data,
- struct drm_file *file_priv);
-+int vc4_get_hang_state_ioctl(struct drm_device *dev, void *data,
-+ struct drm_file *file_priv);
- int vc4_mmap(struct file *filp, struct vm_area_struct *vma);
- int vc4_prime_mmap(struct drm_gem_object *obj, struct vm_area_struct *vma);
- void *vc4_prime_vmap(struct drm_gem_object *obj);
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -40,6 +40,186 @@ vc4_queue_hangcheck(struct drm_device *d
- round_jiffies_up(jiffies + msecs_to_jiffies(100)));
- }
-
-+struct vc4_hang_state {
-+ struct drm_vc4_get_hang_state user_state;
-+
-+ u32 bo_count;
-+ struct drm_gem_object **bo;
-+};
-+
-+static void
-+vc4_free_hang_state(struct drm_device *dev, struct vc4_hang_state *state)
-+{
-+ unsigned int i;
-+
-+ mutex_lock(&dev->struct_mutex);
-+ for (i = 0; i < state->user_state.bo_count; i++) {
-+ drm_gem_object_unreference(state->bo[i]);
-+ }
-+ mutex_unlock(&dev->struct_mutex);
-+
-+ kfree(state);
-+}
-+
-+int
-+vc4_get_hang_state_ioctl(struct drm_device *dev, void *data,
-+ struct drm_file *file_priv)
-+{
-+ struct drm_vc4_get_hang_state *get_state = data;
-+ struct drm_vc4_get_hang_state_bo *bo_state;
-+ struct vc4_hang_state *kernel_state;
-+ struct drm_vc4_get_hang_state *state;
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ unsigned long irqflags;
-+ u32 i;
-+ int ret;
-+
-+ spin_lock_irqsave(&vc4->job_lock, irqflags);
-+ kernel_state = vc4->hang_state;
-+ if (!kernel_state) {
-+ spin_unlock_irqrestore(&vc4->job_lock, irqflags);
-+ return -ENOENT;
-+ }
-+ state = &kernel_state->user_state;
-+
-+ /* If the user's array isn't big enough, just return the
-+ * required array size.
-+ */
-+ if (get_state->bo_count < state->bo_count) {
-+ get_state->bo_count = state->bo_count;
-+ spin_unlock_irqrestore(&vc4->job_lock, irqflags);
-+ return 0;
-+ }
-+
-+ vc4->hang_state = NULL;
-+ spin_unlock_irqrestore(&vc4->job_lock, irqflags);
-+
-+ /* Save the user's BO pointer, so we don't stomp it with the memcpy. */
-+ state->bo = get_state->bo;
-+ memcpy(get_state, state, sizeof(*state));
-+
-+ bo_state = kcalloc(state->bo_count, sizeof(*bo_state), GFP_KERNEL);
-+ if (!bo_state) {
-+ ret = -ENOMEM;
-+ goto err_free;
-+ }
-+
-+ for (i = 0; i < state->bo_count; i++) {
-+ struct vc4_bo *vc4_bo = to_vc4_bo(kernel_state->bo[i]);
-+ u32 handle;
-+ ret = drm_gem_handle_create(file_priv, kernel_state->bo[i],
-+ &handle);
-+
-+ if (ret) {
-+ state->bo_count = i - 1;
-+ goto err;
-+ }
-+ bo_state[i].handle = handle;
-+ bo_state[i].paddr = vc4_bo->base.paddr;
-+ bo_state[i].size = vc4_bo->base.base.size;
-+ }
-+
-+ ret = copy_to_user((void __user *)(uintptr_t)get_state->bo,
-+ bo_state,
-+ state->bo_count * sizeof(*bo_state));
-+ kfree(bo_state);
-+
-+ err_free:
-+
-+ vc4_free_hang_state(dev, kernel_state);
-+
-+err:
-+ return ret;
-+}
-+
-+static void
-+vc4_save_hang_state(struct drm_device *dev)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ struct drm_vc4_get_hang_state *state;
-+ struct vc4_hang_state *kernel_state;
-+ struct vc4_exec_info *exec;
-+ struct vc4_bo *bo;
-+ unsigned long irqflags;
-+ unsigned int i, unref_list_count;
-+
-+ kernel_state = kcalloc(1, sizeof(*state), GFP_KERNEL);
-+ if (!kernel_state)
-+ return;
-+
-+ state = &kernel_state->user_state;
-+
-+ spin_lock_irqsave(&vc4->job_lock, irqflags);
-+ exec = vc4_first_job(vc4);
-+ if (!exec) {
-+ spin_unlock_irqrestore(&vc4->job_lock, irqflags);
-+ return;
-+ }
-+
-+ unref_list_count = 0;
-+ list_for_each_entry(bo, &exec->unref_list, unref_head)
-+ unref_list_count++;
-+
-+ state->bo_count = exec->bo_count + unref_list_count;
-+ kernel_state->bo = kcalloc(state->bo_count, sizeof(*kernel_state->bo),
-+ GFP_ATOMIC);
-+ if (!kernel_state->bo) {
-+ spin_unlock_irqrestore(&vc4->job_lock, irqflags);
-+ return;
-+ }
-+
-+ for (i = 0; i < exec->bo_count; i++) {
-+ drm_gem_object_reference(&exec->bo[i].bo->base);
-+ kernel_state->bo[i] = &exec->bo[i].bo->base;
-+ }
-+
-+ list_for_each_entry(bo, &exec->unref_list, unref_head) {
-+ drm_gem_object_reference(&bo->base.base);
-+ kernel_state->bo[i] = &bo->base.base;
-+ i++;
-+ }
-+
-+ state->start_bin = exec->ct0ca;
-+ state->start_render = exec->ct1ca;
-+
-+ spin_unlock_irqrestore(&vc4->job_lock, irqflags);
-+
-+ state->ct0ca = V3D_READ(V3D_CTNCA(0));
-+ state->ct0ea = V3D_READ(V3D_CTNEA(0));
-+
-+ state->ct1ca = V3D_READ(V3D_CTNCA(1));
-+ state->ct1ea = V3D_READ(V3D_CTNEA(1));
-+
-+ state->ct0cs = V3D_READ(V3D_CTNCS(0));
-+ state->ct1cs = V3D_READ(V3D_CTNCS(1));
-+
-+ state->ct0ra0 = V3D_READ(V3D_CT00RA0);
-+ state->ct1ra0 = V3D_READ(V3D_CT01RA0);
-+
-+ state->bpca = V3D_READ(V3D_BPCA);
-+ state->bpcs = V3D_READ(V3D_BPCS);
-+ state->bpoa = V3D_READ(V3D_BPOA);
-+ state->bpos = V3D_READ(V3D_BPOS);
-+
-+ state->vpmbase = V3D_READ(V3D_VPMBASE);
-+
-+ state->dbge = V3D_READ(V3D_DBGE);
-+ state->fdbgo = V3D_READ(V3D_FDBGO);
-+ state->fdbgb = V3D_READ(V3D_FDBGB);
-+ state->fdbgr = V3D_READ(V3D_FDBGR);
-+ state->fdbgs = V3D_READ(V3D_FDBGS);
-+ state->errstat = V3D_READ(V3D_ERRSTAT);
-+
-+ spin_lock_irqsave(&vc4->job_lock, irqflags);
-+ if (vc4->hang_state) {
-+ spin_unlock_irqrestore(&vc4->job_lock, irqflags);
-+ vc4_free_hang_state(dev, kernel_state);
-+ } else {
-+ vc4->hang_state = kernel_state;
-+ spin_unlock_irqrestore(&vc4->job_lock, irqflags);
-+ }
-+}
-+
- static void
- vc4_reset(struct drm_device *dev)
- {
-@@ -64,6 +244,8 @@ vc4_reset_work(struct work_struct *work)
- struct vc4_dev *vc4 =
- container_of(work, struct vc4_dev, hangcheck.reset_work);
-
-+ vc4_save_hang_state(vc4->dev);
-+
- vc4_reset(vc4->dev);
- }
-
-@@ -673,4 +855,7 @@ vc4_gem_destroy(struct drm_device *dev)
- }
-
- vc4_bo_cache_destroy(dev);
-+
-+ if (vc4->hang_state)
-+ vc4_free_hang_state(dev, vc4->hang_state);
- }
---- a/include/uapi/drm/vc4_drm.h
-+++ b/include/uapi/drm/vc4_drm.h
-@@ -32,6 +32,7 @@
- #define DRM_VC4_CREATE_BO 0x03
- #define DRM_VC4_MMAP_BO 0x04
- #define DRM_VC4_CREATE_SHADER_BO 0x05
-+#define DRM_VC4_GET_HANG_STATE 0x06
-
- #define DRM_IOCTL_VC4_SUBMIT_CL DRM_IOWR( DRM_COMMAND_BASE + DRM_VC4_SUBMIT_CL, struct drm_vc4_submit_cl)
- #define DRM_IOCTL_VC4_WAIT_SEQNO DRM_IOWR( DRM_COMMAND_BASE + DRM_VC4_WAIT_SEQNO, struct drm_vc4_wait_seqno)
-@@ -39,6 +40,7 @@
- #define DRM_IOCTL_VC4_CREATE_BO DRM_IOWR( DRM_COMMAND_BASE + DRM_VC4_CREATE_BO, struct drm_vc4_create_bo)
- #define DRM_IOCTL_VC4_MMAP_BO DRM_IOWR( DRM_COMMAND_BASE + DRM_VC4_MMAP_BO, struct drm_vc4_mmap_bo)
- #define DRM_IOCTL_VC4_CREATE_SHADER_BO DRM_IOWR( DRM_COMMAND_BASE + DRM_VC4_CREATE_SHADER_BO, struct drm_vc4_create_shader_bo)
-+#define DRM_IOCTL_VC4_GET_HANG_STATE DRM_IOWR( DRM_COMMAND_BASE + DRM_VC4_GET_HANG_STATE, struct drm_vc4_get_hang_state)
-
- struct drm_vc4_submit_rcl_surface {
- uint32_t hindex; /* Handle index, or ~0 if not present. */
-@@ -226,4 +228,47 @@ struct drm_vc4_mmap_bo {
- uint64_t offset;
- };
-
-+struct drm_vc4_get_hang_state_bo {
-+ uint32_t handle;
-+ uint32_t paddr;
-+ uint32_t size;
-+ uint32_t pad;
-+};
-+
-+/**
-+ * struct drm_vc4_hang_state - ioctl argument for collecting state
-+ * from a GPU hang for analysis.
-+*/
-+struct drm_vc4_get_hang_state {
-+ /** Pointer to array of struct drm_vc4_get_hang_state_bo. */
-+ uint64_t bo;
-+ /**
-+ * On input, the size of the bo array. Output is the number
-+ * of bos to be returned.
-+ */
-+ uint32_t bo_count;
-+
-+ uint32_t start_bin, start_render;
-+
-+ uint32_t ct0ca, ct0ea;
-+ uint32_t ct1ca, ct1ea;
-+ uint32_t ct0cs, ct1cs;
-+ uint32_t ct0ra0, ct1ra0;
-+
-+ uint32_t bpca, bpcs;
-+ uint32_t bpoa, bpos;
-+
-+ uint32_t vpmbase;
-+
-+ uint32_t dbge;
-+ uint32_t fdbgo;
-+ uint32_t fdbgb;
-+ uint32_t fdbgr;
-+ uint32_t fdbgs;
-+ uint32_t errstat;
-+
-+ /* Pad that we may save more registers into in the future. */
-+ uint32_t pad[16];
-+};
-+
- #endif /* _UAPI_VC4_DRM_H_ */
diff --git a/target/linux/brcm2708/patches-4.4/0114-drm-vc4-Update-a-bunch-of-code-to-match-upstream-sub.patch b/target/linux/brcm2708/patches-4.4/0114-drm-vc4-Update-a-bunch-of-code-to-match-upstream-sub.patch
deleted file mode 100644
index dc6949a..0000000
--- a/target/linux/brcm2708/patches-4.4/0114-drm-vc4-Update-a-bunch-of-code-to-match-upstream-sub.patch
+++ /dev/null
@@ -1,1893 +0,0 @@
-From f6c3cdbb026c7b516694d2cf285ff4c5434f34bf Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 4 Dec 2015 11:35:34 -0800
-Subject: [PATCH] drm/vc4: Update a bunch of code to match upstream submission.
-
-This gets almost everything matching, except for the MSAA support and
-using generic PM domains.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/drm_gem_cma_helper.c | 13 +-
- drivers/gpu/drm/vc4/vc4_bo.c | 322 +++++++++++++++++------------
- drivers/gpu/drm/vc4/vc4_crtc.c | 7 +-
- drivers/gpu/drm/vc4/vc4_drv.c | 6 +-
- drivers/gpu/drm/vc4/vc4_drv.h | 20 +-
- drivers/gpu/drm/vc4/vc4_gem.c | 24 ++-
- drivers/gpu/drm/vc4/vc4_irq.c | 5 +-
- drivers/gpu/drm/vc4/vc4_kms.c | 1 +
- drivers/gpu/drm/vc4/vc4_packet.h | 210 +++++++++----------
- drivers/gpu/drm/vc4/vc4_qpu_defines.h | 308 ++++++++++++++-------------
- drivers/gpu/drm/vc4/vc4_render_cl.c | 4 +-
- drivers/gpu/drm/vc4/vc4_v3d.c | 10 +-
- drivers/gpu/drm/vc4/vc4_validate.c | 130 ++++++------
- drivers/gpu/drm/vc4/vc4_validate_shaders.c | 66 +++---
- include/drm/drmP.h | 8 +-
- 15 files changed, 598 insertions(+), 536 deletions(-)
-
---- a/drivers/gpu/drm/drm_gem_cma_helper.c
-+++ b/drivers/gpu/drm/drm_gem_cma_helper.c
-@@ -58,15 +58,14 @@ __drm_gem_cma_create(struct drm_device *
- struct drm_gem_cma_object *cma_obj;
- struct drm_gem_object *gem_obj;
- int ret;
-- size_t obj_size = (drm->driver->gem_obj_size ?
-- drm->driver->gem_obj_size :
-- sizeof(*cma_obj));
-
-- cma_obj = kzalloc(obj_size, GFP_KERNEL);
-- if (!cma_obj)
-+ if (drm->driver->gem_create_object)
-+ gem_obj = drm->driver->gem_create_object(drm, size);
-+ else
-+ gem_obj = kzalloc(sizeof(*cma_obj), GFP_KERNEL);
-+ if (!gem_obj)
- return ERR_PTR(-ENOMEM);
--
-- gem_obj = &cma_obj->base;
-+ cma_obj = container_of(gem_obj, struct drm_gem_cma_object, base);
-
- ret = drm_gem_object_init(drm, gem_obj, size);
- if (ret)
---- a/drivers/gpu/drm/vc4/vc4_bo.c
-+++ b/drivers/gpu/drm/vc4/vc4_bo.c
-@@ -12,6 +12,10 @@
- * access to system memory with no MMU in between. To support it, we
- * use the GEM CMA helper functions to allocate contiguous ranges of
- * physical memory for our BOs.
-+ *
-+ * Since the CMA allocator is very slow, we keep a cache of recently
-+ * freed BOs around so that the kernel's allocation of objects for 3D
-+ * rendering can return quickly.
- */
-
- #include "vc4_drv.h"
-@@ -34,6 +38,36 @@ static void vc4_bo_stats_dump(struct vc4
- vc4->bo_stats.size_cached / 1024);
- }
-
-+#ifdef CONFIG_DEBUG_FS
-+int vc4_bo_stats_debugfs(struct seq_file *m, void *unused)
-+{
-+ struct drm_info_node *node = (struct drm_info_node *)m->private;
-+ struct drm_device *dev = node->minor->dev;
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ struct vc4_bo_stats stats;
-+
-+ /* Take a snapshot of the current stats with the lock held. */
-+ mutex_lock(&vc4->bo_lock);
-+ stats = vc4->bo_stats;
-+ mutex_unlock(&vc4->bo_lock);
-+
-+ seq_printf(m, "num bos allocated: %d\n",
-+ stats.num_allocated);
-+ seq_printf(m, "size bos allocated: %dkb\n",
-+ stats.size_allocated / 1024);
-+ seq_printf(m, "num bos used: %d\n",
-+ stats.num_allocated - stats.num_cached);
-+ seq_printf(m, "size bos used: %dkb\n",
-+ (stats.size_allocated - stats.size_cached) / 1024);
-+ seq_printf(m, "num bos cached: %d\n",
-+ stats.num_cached);
-+ seq_printf(m, "size bos cached: %dkb\n",
-+ stats.size_cached / 1024);
-+
-+ return 0;
-+}
-+#endif
-+
- static uint32_t bo_page_index(size_t size)
- {
- return (size / PAGE_SIZE) - 1;
-@@ -81,8 +115,8 @@ static struct list_head *vc4_get_cache_l
- struct list_head *new_list;
- uint32_t i;
-
-- new_list = kmalloc(new_size * sizeof(struct list_head),
-- GFP_KERNEL);
-+ new_list = kmalloc_array(new_size, sizeof(struct list_head),
-+ GFP_KERNEL);
- if (!new_list)
- return NULL;
-
-@@ -90,7 +124,9 @@ static struct list_head *vc4_get_cache_l
- * head locations.
- */
- for (i = 0; i < vc4->bo_cache.size_list_size; i++) {
-- struct list_head *old_list = &vc4->bo_cache.size_list[i];
-+ struct list_head *old_list =
-+ &vc4->bo_cache.size_list[i];
-+
- if (list_empty(old_list))
- INIT_LIST_HEAD(&new_list[i]);
- else
-@@ -122,11 +158,60 @@ void vc4_bo_cache_purge(struct drm_devic
- mutex_unlock(&vc4->bo_lock);
- }
-
--struct vc4_bo *vc4_bo_create(struct drm_device *dev, size_t unaligned_size)
-+static struct vc4_bo *vc4_bo_get_from_cache(struct drm_device *dev,
-+ uint32_t size)
- {
- struct vc4_dev *vc4 = to_vc4_dev(dev);
-- uint32_t size = roundup(unaligned_size, PAGE_SIZE);
- uint32_t page_index = bo_page_index(size);
-+ struct vc4_bo *bo = NULL;
-+
-+ size = roundup(size, PAGE_SIZE);
-+
-+ mutex_lock(&vc4->bo_lock);
-+ if (page_index >= vc4->bo_cache.size_list_size)
-+ goto out;
-+
-+ if (list_empty(&vc4->bo_cache.size_list[page_index]))
-+ goto out;
-+
-+ bo = list_first_entry(&vc4->bo_cache.size_list[page_index],
-+ struct vc4_bo, size_head);
-+ vc4_bo_remove_from_cache(bo);
-+ kref_init(&bo->base.base.refcount);
-+
-+out:
-+ mutex_unlock(&vc4->bo_lock);
-+ return bo;
-+}
-+
-+/**
-+ * vc4_gem_create_object - Implementation of driver->gem_create_object.
-+ *
-+ * This lets the CMA helpers allocate object structs for us, and keep
-+ * our BO stats correct.
-+ */
-+struct drm_gem_object *vc4_create_object(struct drm_device *dev, size_t size)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ struct vc4_bo *bo;
-+
-+ bo = kzalloc(sizeof(*bo), GFP_KERNEL);
-+ if (!bo)
-+ return ERR_PTR(-ENOMEM);
-+
-+ mutex_lock(&vc4->bo_lock);
-+ vc4->bo_stats.num_allocated++;
-+ vc4->bo_stats.size_allocated += size;
-+ mutex_unlock(&vc4->bo_lock);
-+
-+ return &bo->base.base;
-+}
-+
-+struct vc4_bo *vc4_bo_create(struct drm_device *dev, size_t unaligned_size,
-+ bool from_cache)
-+{
-+ size_t size = roundup(unaligned_size, PAGE_SIZE);
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct drm_gem_cma_object *cma_obj;
- int pass;
-
-@@ -134,18 +219,12 @@ struct vc4_bo *vc4_bo_create(struct drm_
- return NULL;
-
- /* First, try to get a vc4_bo from the kernel BO cache. */
-- mutex_lock(&vc4->bo_lock);
-- if (page_index < vc4->bo_cache.size_list_size &&
-- !list_empty(&vc4->bo_cache.size_list[page_index])) {
-- struct vc4_bo *bo =
-- list_first_entry(&vc4->bo_cache.size_list[page_index],
-- struct vc4_bo, size_head);
-- vc4_bo_remove_from_cache(bo);
-- mutex_unlock(&vc4->bo_lock);
-- kref_init(&bo->base.base.refcount);
-- return bo;
-+ if (from_cache) {
-+ struct vc4_bo *bo = vc4_bo_get_from_cache(dev, size);
-+
-+ if (bo)
-+ return bo;
- }
-- mutex_unlock(&vc4->bo_lock);
-
- /* Otherwise, make a new BO. */
- for (pass = 0; ; pass++) {
-@@ -179,9 +258,6 @@ struct vc4_bo *vc4_bo_create(struct drm_
- }
- }
-
-- vc4->bo_stats.num_allocated++;
-- vc4->bo_stats.size_allocated += size;
--
- return to_vc4_bo(&cma_obj->base);
- }
-
-@@ -199,7 +275,7 @@ int vc4_dumb_create(struct drm_file *fil
- if (args->size < args->pitch * args->height)
- args->size = args->pitch * args->height;
-
-- bo = vc4_bo_create(dev, args->size);
-+ bo = vc4_bo_create(dev, args->size, false);
- if (!bo)
- return -ENOMEM;
-
-@@ -209,8 +285,8 @@ int vc4_dumb_create(struct drm_file *fil
- return ret;
- }
-
--static void
--vc4_bo_cache_free_old(struct drm_device *dev)
-+/* Must be called with bo_lock held. */
-+static void vc4_bo_cache_free_old(struct drm_device *dev)
- {
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- unsigned long expire_time = jiffies - msecs_to_jiffies(1000);
-@@ -313,15 +389,77 @@ vc4_prime_export(struct drm_device *dev,
- return drm_gem_prime_export(dev, obj, flags);
- }
-
--int
--vc4_create_bo_ioctl(struct drm_device *dev, void *data,
-- struct drm_file *file_priv)
-+int vc4_mmap(struct file *filp, struct vm_area_struct *vma)
-+{
-+ struct drm_gem_object *gem_obj;
-+ struct vc4_bo *bo;
-+ int ret;
-+
-+ ret = drm_gem_mmap(filp, vma);
-+ if (ret)
-+ return ret;
-+
-+ gem_obj = vma->vm_private_data;
-+ bo = to_vc4_bo(gem_obj);
-+
-+ if (bo->validated_shader && (vma->vm_flags & VM_WRITE)) {
-+ DRM_ERROR("mmaping of shader BOs for writing not allowed.\n");
-+ return -EINVAL;
-+ }
-+
-+ /*
-+ * Clear the VM_PFNMAP flag that was set by drm_gem_mmap(), and set the
-+ * vm_pgoff (used as a fake buffer offset by DRM) to 0 as we want to map
-+ * the whole buffer.
-+ */
-+ vma->vm_flags &= ~VM_PFNMAP;
-+ vma->vm_pgoff = 0;
-+
-+ ret = dma_mmap_writecombine(bo->base.base.dev->dev, vma,
-+ bo->base.vaddr, bo->base.paddr,
-+ vma->vm_end - vma->vm_start);
-+ if (ret)
-+ drm_gem_vm_close(vma);
-+
-+ return ret;
-+}
-+
-+int vc4_prime_mmap(struct drm_gem_object *obj, struct vm_area_struct *vma)
-+{
-+ struct vc4_bo *bo = to_vc4_bo(obj);
-+
-+ if (bo->validated_shader && (vma->vm_flags & VM_WRITE)) {
-+ DRM_ERROR("mmaping of shader BOs for writing not allowed.\n");
-+ return -EINVAL;
-+ }
-+
-+ return drm_gem_cma_prime_mmap(obj, vma);
-+}
-+
-+void *vc4_prime_vmap(struct drm_gem_object *obj)
-+{
-+ struct vc4_bo *bo = to_vc4_bo(obj);
-+
-+ if (bo->validated_shader) {
-+ DRM_ERROR("mmaping of shader BOs not allowed.\n");
-+ return ERR_PTR(-EINVAL);
-+ }
-+
-+ return drm_gem_cma_prime_vmap(obj);
-+}
-+
-+int vc4_create_bo_ioctl(struct drm_device *dev, void *data,
-+ struct drm_file *file_priv)
- {
- struct drm_vc4_create_bo *args = data;
- struct vc4_bo *bo = NULL;
- int ret;
-
-- bo = vc4_bo_create(dev, args->size);
-+ /*
-+ * We can't allocate from the BO cache, because the BOs don't
-+ * get zeroed, and that might leak data between users.
-+ */
-+ bo = vc4_bo_create(dev, args->size, false);
- if (!bo)
- return -ENOMEM;
-
-@@ -331,6 +469,25 @@ vc4_create_bo_ioctl(struct drm_device *d
- return ret;
- }
-
-+int vc4_mmap_bo_ioctl(struct drm_device *dev, void *data,
-+ struct drm_file *file_priv)
-+{
-+ struct drm_vc4_mmap_bo *args = data;
-+ struct drm_gem_object *gem_obj;
-+
-+ gem_obj = drm_gem_object_lookup(dev, file_priv, args->handle);
-+ if (!gem_obj) {
-+ DRM_ERROR("Failed to look up GEM BO %d\n", args->handle);
-+ return -EINVAL;
-+ }
-+
-+ /* The mmap offset was set up at BO allocation time. */
-+ args->offset = drm_vma_node_offset_addr(&gem_obj->vma_node);
-+
-+ drm_gem_object_unreference_unlocked(gem_obj);
-+ return 0;
-+}
-+
- int
- vc4_create_shader_bo_ioctl(struct drm_device *dev, void *data,
- struct drm_file *file_priv)
-@@ -355,7 +512,7 @@ vc4_create_shader_bo_ioctl(struct drm_de
- return -EINVAL;
- }
-
-- bo = vc4_bo_create(dev, args->size);
-+ bo = vc4_bo_create(dev, args->size, true);
- if (!bo)
- return -ENOMEM;
-
-@@ -364,6 +521,11 @@ vc4_create_shader_bo_ioctl(struct drm_de
- args->size);
- if (ret != 0)
- goto fail;
-+ /* Clear the rest of the memory from allocating from the BO
-+ * cache.
-+ */
-+ memset(bo->base.vaddr + args->size, 0,
-+ bo->base.base.size - args->size);
-
- bo->validated_shader = vc4_validate_shader(&bo->base);
- if (!bo->validated_shader) {
-@@ -382,85 +544,6 @@ vc4_create_shader_bo_ioctl(struct drm_de
- return ret;
- }
-
--int
--vc4_mmap_bo_ioctl(struct drm_device *dev, void *data,
-- struct drm_file *file_priv)
--{
-- struct drm_vc4_mmap_bo *args = data;
-- struct drm_gem_object *gem_obj;
--
-- gem_obj = drm_gem_object_lookup(dev, file_priv, args->handle);
-- if (!gem_obj) {
-- DRM_ERROR("Failed to look up GEM BO %d\n", args->handle);
-- return -EINVAL;
-- }
--
-- /* The mmap offset was set up at BO allocation time. */
-- args->offset = drm_vma_node_offset_addr(&gem_obj->vma_node);
--
-- drm_gem_object_unreference(gem_obj);
-- return 0;
--}
--
--int vc4_mmap(struct file *filp, struct vm_area_struct *vma)
--{
-- struct drm_gem_object *gem_obj;
-- struct vc4_bo *bo;
-- int ret;
--
-- ret = drm_gem_mmap(filp, vma);
-- if (ret)
-- return ret;
--
-- gem_obj = vma->vm_private_data;
-- bo = to_vc4_bo(gem_obj);
--
-- if (bo->validated_shader && (vma->vm_flags & VM_WRITE)) {
-- DRM_ERROR("mmaping of shader BOs for writing not allowed.\n");
-- return -EINVAL;
-- }
--
-- /*
-- * Clear the VM_PFNMAP flag that was set by drm_gem_mmap(), and set the
-- * vm_pgoff (used as a fake buffer offset by DRM) to 0 as we want to map
-- * the whole buffer.
-- */
-- vma->vm_flags &= ~VM_PFNMAP;
-- vma->vm_pgoff = 0;
--
-- ret = dma_mmap_writecombine(bo->base.base.dev->dev, vma,
-- bo->base.vaddr, bo->base.paddr,
-- vma->vm_end - vma->vm_start);
-- if (ret)
-- drm_gem_vm_close(vma);
--
-- return ret;
--}
--
--int vc4_prime_mmap(struct drm_gem_object *obj, struct vm_area_struct *vma)
--{
-- struct vc4_bo *bo = to_vc4_bo(obj);
--
-- if (bo->validated_shader) {
-- DRM_ERROR("mmaping of shader BOs not allowed.\n");
-- return -EINVAL;
-- }
--
-- return drm_gem_cma_prime_mmap(obj, vma);
--}
--
--void *vc4_prime_vmap(struct drm_gem_object *obj)
--{
-- struct vc4_bo *bo = to_vc4_bo(obj);
--
-- if (bo->validated_shader) {
-- DRM_ERROR("mmaping of shader BOs not allowed.\n");
-- return ERR_PTR(-EINVAL);
-- }
--
-- return drm_gem_cma_prime_vmap(obj);
--}
--
- void vc4_bo_cache_init(struct drm_device *dev)
- {
- struct vc4_dev *vc4 = to_vc4_dev(dev);
-@@ -472,7 +555,7 @@ void vc4_bo_cache_init(struct drm_device
- INIT_WORK(&vc4->bo_cache.time_work, vc4_bo_cache_time_work);
- setup_timer(&vc4->bo_cache.time_timer,
- vc4_bo_cache_time_timer,
-- (unsigned long) dev);
-+ (unsigned long)dev);
- }
-
- void vc4_bo_cache_destroy(struct drm_device *dev)
-@@ -489,28 +572,3 @@ void vc4_bo_cache_destroy(struct drm_dev
- vc4_bo_stats_dump(vc4);
- }
- }
--
--#ifdef CONFIG_DEBUG_FS
--int vc4_bo_stats_debugfs(struct seq_file *m, void *unused)
--{
-- struct drm_info_node *node = (struct drm_info_node *) m->private;
-- struct drm_device *dev = node->minor->dev;
-- struct vc4_dev *vc4 = to_vc4_dev(dev);
-- struct vc4_bo_stats stats;
--
-- mutex_lock(&vc4->bo_lock);
-- stats = vc4->bo_stats;
-- mutex_unlock(&vc4->bo_lock);
--
-- seq_printf(m, "num bos allocated: %d\n", stats.num_allocated);
-- seq_printf(m, "size bos allocated: %dkb\n", stats.size_allocated / 1024);
-- seq_printf(m, "num bos used: %d\n", (stats.num_allocated -
-- stats.num_cached));
-- seq_printf(m, "size bos used: %dkb\n", (stats.size_allocated -
-- stats.size_cached) / 1024);
-- seq_printf(m, "num bos cached: %d\n", stats.num_cached);
-- seq_printf(m, "size bos cached: %dkb\n", stats.size_cached / 1024);
--
-- return 0;
--}
--#endif
---- a/drivers/gpu/drm/vc4/vc4_crtc.c
-+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
-@@ -501,6 +501,7 @@ vc4_async_page_flip_complete(struct vc4_
- vc4_plane_async_set_fb(plane, flip_state->fb);
- if (flip_state->event) {
- unsigned long flags;
-+
- spin_lock_irqsave(&dev->event_lock, flags);
- drm_crtc_send_vblank_event(crtc, flip_state->event);
- spin_unlock_irqrestore(&dev->event_lock, flags);
-@@ -562,9 +563,9 @@ static int vc4_async_page_flip(struct dr
- }
-
- static int vc4_page_flip(struct drm_crtc *crtc,
-- struct drm_framebuffer *fb,
-- struct drm_pending_vblank_event *event,
-- uint32_t flags)
-+ struct drm_framebuffer *fb,
-+ struct drm_pending_vblank_event *event,
-+ uint32_t flags)
- {
- if (flags & DRM_MODE_PAGE_FLIP_ASYNC)
- return vc4_async_page_flip(crtc, fb, event, flags);
---- a/drivers/gpu/drm/vc4/vc4_drv.c
-+++ b/drivers/gpu/drm/vc4/vc4_drv.c
-@@ -81,7 +81,8 @@ static const struct drm_ioctl_desc vc4_d
- DRM_IOCTL_DEF_DRV(VC4_CREATE_BO, vc4_create_bo_ioctl, 0),
- DRM_IOCTL_DEF_DRV(VC4_MMAP_BO, vc4_mmap_bo_ioctl, 0),
- DRM_IOCTL_DEF_DRV(VC4_CREATE_SHADER_BO, vc4_create_shader_bo_ioctl, 0),
-- DRM_IOCTL_DEF_DRV(VC4_GET_HANG_STATE, vc4_get_hang_state_ioctl, DRM_ROOT_ONLY),
-+ DRM_IOCTL_DEF_DRV(VC4_GET_HANG_STATE, vc4_get_hang_state_ioctl,
-+ DRM_ROOT_ONLY),
- };
-
- static struct drm_driver vc4_drm_driver = {
-@@ -107,6 +108,7 @@ static struct drm_driver vc4_drm_driver
- .debugfs_cleanup = vc4_debugfs_cleanup,
- #endif
-
-+ .gem_create_object = vc4_create_object,
- .gem_free_object = vc4_free_object,
- .gem_vm_ops = &drm_gem_cma_vm_ops,
-
-@@ -128,8 +130,6 @@ static struct drm_driver vc4_drm_driver
- .num_ioctls = ARRAY_SIZE(vc4_drm_ioctls),
- .fops = &vc4_drm_fops,
-
-- //.gem_obj_size = sizeof(struct vc4_bo),
--
- .name = DRIVER_NAME,
- .desc = DRIVER_DESC,
- .date = DRIVER_DATE,
---- a/drivers/gpu/drm/vc4/vc4_drv.h
-+++ b/drivers/gpu/drm/vc4/vc4_drv.h
-@@ -72,6 +72,9 @@ struct vc4_dev {
- * job_done_work.
- */
- struct list_head job_done_list;
-+ /* Spinlock used to synchronize the job_list and seqno
-+ * accesses between the IRQ handler and GEM ioctls.
-+ */
- spinlock_t job_lock;
- wait_queue_head_t job_wait_queue;
- struct work_struct job_done_work;
-@@ -318,8 +321,7 @@ struct vc4_texture_sample_info {
- * and validate the shader state record's uniforms that define the texture
- * samples.
- */
--struct vc4_validated_shader_info
--{
-+struct vc4_validated_shader_info {
- uint32_t uniforms_size;
- uint32_t uniforms_src_size;
- uint32_t num_texture_samples;
-@@ -355,8 +357,10 @@ struct vc4_validated_shader_info
- #define wait_for(COND, MS) _wait_for(COND, MS, 1)
-
- /* vc4_bo.c */
-+struct drm_gem_object *vc4_create_object(struct drm_device *dev, size_t size);
- void vc4_free_object(struct drm_gem_object *gem_obj);
--struct vc4_bo *vc4_bo_create(struct drm_device *dev, size_t size);
-+struct vc4_bo *vc4_bo_create(struct drm_device *dev, size_t size,
-+ bool from_cache);
- int vc4_dumb_create(struct drm_file *file_priv,
- struct drm_device *dev,
- struct drm_mode_create_dumb *args);
-@@ -432,7 +436,8 @@ struct drm_plane *vc4_plane_init(struct
- enum drm_plane_type type);
- u32 vc4_plane_write_dlist(struct drm_plane *plane, u32 __iomem *dlist);
- u32 vc4_plane_dlist_size(struct drm_plane_state *state);
--void vc4_plane_async_set_fb(struct drm_plane *plane, struct drm_framebuffer *fb);
-+void vc4_plane_async_set_fb(struct drm_plane *plane,
-+ struct drm_framebuffer *fb);
-
- /* vc4_v3d.c */
- extern struct platform_driver vc4_v3d_driver;
-@@ -450,9 +455,6 @@ vc4_validate_bin_cl(struct drm_device *d
- int
- vc4_validate_shader_recs(struct drm_device *dev, struct vc4_exec_info *exec);
-
--struct vc4_validated_shader_info *
--vc4_validate_shader(struct drm_gem_cma_object *shader_obj);
--
- bool vc4_use_bo(struct vc4_exec_info *exec,
- uint32_t hindex,
- enum vc4_bo_mode mode,
-@@ -464,3 +466,7 @@ bool vc4_check_tex_size(struct vc4_exec_
- struct drm_gem_cma_object *fbo,
- uint32_t offset, uint8_t tiling_format,
- uint32_t width, uint32_t height, uint8_t cpp);
-+
-+/* vc4_validate_shader.c */
-+struct vc4_validated_shader_info *
-+vc4_validate_shader(struct drm_gem_cma_object *shader_obj);
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -53,9 +53,8 @@ vc4_free_hang_state(struct drm_device *d
- unsigned int i;
-
- mutex_lock(&dev->struct_mutex);
-- for (i = 0; i < state->user_state.bo_count; i++) {
-+ for (i = 0; i < state->user_state.bo_count; i++)
- drm_gem_object_unreference(state->bo[i]);
-- }
- mutex_unlock(&dev->struct_mutex);
-
- kfree(state);
-@@ -65,10 +64,10 @@ int
- vc4_get_hang_state_ioctl(struct drm_device *dev, void *data,
- struct drm_file *file_priv)
- {
-- struct drm_vc4_get_hang_state *get_state = data;
-+ struct drm_vc4_get_hang_state *get_state = data;
- struct drm_vc4_get_hang_state_bo *bo_state;
- struct vc4_hang_state *kernel_state;
-- struct drm_vc4_get_hang_state *state;
-+ struct drm_vc4_get_hang_state *state;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- unsigned long irqflags;
- u32 i;
-@@ -107,6 +106,7 @@ vc4_get_hang_state_ioctl(struct drm_devi
- for (i = 0; i < state->bo_count; i++) {
- struct vc4_bo *vc4_bo = to_vc4_bo(kernel_state->bo[i]);
- u32 handle;
-+
- ret = drm_gem_handle_create(file_priv, kernel_state->bo[i],
- &handle);
-
-@@ -124,7 +124,7 @@ vc4_get_hang_state_ioctl(struct drm_devi
- state->bo_count * sizeof(*bo_state));
- kfree(bo_state);
-
-- err_free:
-+err_free:
-
- vc4_free_hang_state(dev, kernel_state);
-
-@@ -578,7 +578,7 @@ vc4_get_bcl(struct drm_device *dev, stru
- goto fail;
- }
-
-- bo = vc4_bo_create(dev, exec_size);
-+ bo = vc4_bo_create(dev, exec_size, true);
- if (!bo) {
- DRM_ERROR("Couldn't allocate BO for binning\n");
- ret = PTR_ERR(exec->exec_bo);
-@@ -668,6 +668,7 @@ vc4_job_handle_completed(struct vc4_dev
- static void vc4_seqno_cb_work(struct work_struct *work)
- {
- struct vc4_seqno_cb *cb = container_of(work, struct vc4_seqno_cb, work);
-+
- cb->func(cb);
- }
-
-@@ -717,6 +718,7 @@ vc4_wait_for_seqno_ioctl_helper(struct d
-
- if ((ret == -EINTR || ret == -ERESTARTSYS) && *timeout_ns != ~0ull) {
- uint64_t delta = jiffies_to_nsecs(jiffies - start);
-+
- if (*timeout_ns >= delta)
- *timeout_ns -= delta;
- }
-@@ -750,9 +752,10 @@ vc4_wait_bo_ioctl(struct drm_device *dev
- }
- bo = to_vc4_bo(gem_obj);
-
-- ret = vc4_wait_for_seqno_ioctl_helper(dev, bo->seqno, &args->timeout_ns);
-+ ret = vc4_wait_for_seqno_ioctl_helper(dev, bo->seqno,
-+ &args->timeout_ns);
-
-- drm_gem_object_unreference(gem_obj);
-+ drm_gem_object_unreference_unlocked(gem_obj);
- return ret;
- }
-
-@@ -793,7 +796,8 @@ vc4_submit_cl_ioctl(struct drm_device *d
- if (ret)
- goto fail;
- } else {
-- exec->ct0ca = exec->ct0ea = 0;
-+ exec->ct0ca = 0;
-+ exec->ct0ea = 0;
- }
-
- ret = vc4_get_rcl(dev, exec);
-@@ -831,7 +835,7 @@ vc4_gem_init(struct drm_device *dev)
- INIT_WORK(&vc4->hangcheck.reset_work, vc4_reset_work);
- setup_timer(&vc4->hangcheck.timer,
- vc4_hangcheck_elapsed,
-- (unsigned long) dev);
-+ (unsigned long)dev);
-
- INIT_WORK(&vc4->job_done_work, vc4_job_done_work);
- }
---- a/drivers/gpu/drm/vc4/vc4_irq.c
-+++ b/drivers/gpu/drm/vc4/vc4_irq.c
-@@ -56,7 +56,7 @@ vc4_overflow_mem_work(struct work_struct
- struct drm_device *dev = vc4->dev;
- struct vc4_bo *bo;
-
-- bo = vc4_bo_create(dev, 256 * 1024);
-+ bo = vc4_bo_create(dev, 256 * 1024, true);
- if (!bo) {
- DRM_ERROR("Couldn't allocate binner overflow mem\n");
- return;
-@@ -87,9 +87,8 @@ vc4_overflow_mem_work(struct work_struct
- spin_unlock_irqrestore(&vc4->job_lock, irqflags);
- }
-
-- if (vc4->overflow_mem) {
-+ if (vc4->overflow_mem)
- drm_gem_object_unreference_unlocked(&vc4->overflow_mem->base.base);
-- }
- vc4->overflow_mem = bo;
-
- V3D_WRITE(V3D_BPOA, bo->base.paddr);
---- a/drivers/gpu/drm/vc4/vc4_kms.c
-+++ b/drivers/gpu/drm/vc4/vc4_kms.c
-@@ -132,6 +132,7 @@ static int vc4_atomic_commit(struct drm_
- struct drm_gem_cma_object *cma_bo =
- drm_fb_cma_get_gem_obj(new_state->fb, 0);
- struct vc4_bo *bo = to_vc4_bo(&cma_bo->base);
-+
- wait_seqno = max(bo->seqno, wait_seqno);
- }
- }
---- a/drivers/gpu/drm/vc4/vc4_packet.h
-+++ b/drivers/gpu/drm/vc4/vc4_packet.h
-@@ -27,60 +27,60 @@
- #include "vc4_regs.h" /* for VC4_MASK, VC4_GET_FIELD, VC4_SET_FIELD */
-
- enum vc4_packet {
-- VC4_PACKET_HALT = 0,
-- VC4_PACKET_NOP = 1,
-+ VC4_PACKET_HALT = 0,
-+ VC4_PACKET_NOP = 1,
-
-- VC4_PACKET_FLUSH = 4,
-- VC4_PACKET_FLUSH_ALL = 5,
-- VC4_PACKET_START_TILE_BINNING = 6,
-- VC4_PACKET_INCREMENT_SEMAPHORE = 7,
-- VC4_PACKET_WAIT_ON_SEMAPHORE = 8,
--
-- VC4_PACKET_BRANCH = 16,
-- VC4_PACKET_BRANCH_TO_SUB_LIST = 17,
--
-- VC4_PACKET_STORE_MS_TILE_BUFFER = 24,
-- VC4_PACKET_STORE_MS_TILE_BUFFER_AND_EOF = 25,
-- VC4_PACKET_STORE_FULL_RES_TILE_BUFFER = 26,
-- VC4_PACKET_LOAD_FULL_RES_TILE_BUFFER = 27,
-- VC4_PACKET_STORE_TILE_BUFFER_GENERAL = 28,
-- VC4_PACKET_LOAD_TILE_BUFFER_GENERAL = 29,
--
-- VC4_PACKET_GL_INDEXED_PRIMITIVE = 32,
-- VC4_PACKET_GL_ARRAY_PRIMITIVE = 33,
--
-- VC4_PACKET_COMPRESSED_PRIMITIVE = 48,
-- VC4_PACKET_CLIPPED_COMPRESSED_PRIMITIVE = 49,
--
-- VC4_PACKET_PRIMITIVE_LIST_FORMAT = 56,
--
-- VC4_PACKET_GL_SHADER_STATE = 64,
-- VC4_PACKET_NV_SHADER_STATE = 65,
-- VC4_PACKET_VG_SHADER_STATE = 66,
--
-- VC4_PACKET_CONFIGURATION_BITS = 96,
-- VC4_PACKET_FLAT_SHADE_FLAGS = 97,
-- VC4_PACKET_POINT_SIZE = 98,
-- VC4_PACKET_LINE_WIDTH = 99,
-- VC4_PACKET_RHT_X_BOUNDARY = 100,
-- VC4_PACKET_DEPTH_OFFSET = 101,
-- VC4_PACKET_CLIP_WINDOW = 102,
-- VC4_PACKET_VIEWPORT_OFFSET = 103,
-- VC4_PACKET_Z_CLIPPING = 104,
-- VC4_PACKET_CLIPPER_XY_SCALING = 105,
-- VC4_PACKET_CLIPPER_Z_SCALING = 106,
--
-- VC4_PACKET_TILE_BINNING_MODE_CONFIG = 112,
-- VC4_PACKET_TILE_RENDERING_MODE_CONFIG = 113,
-- VC4_PACKET_CLEAR_COLORS = 114,
-- VC4_PACKET_TILE_COORDINATES = 115,
--
-- /* Not an actual hardware packet -- this is what we use to put
-- * references to GEM bos in the command stream, since we need the u32
-- * int the actual address packet in order to store the offset from the
-- * start of the BO.
-- */
-- VC4_PACKET_GEM_HANDLES = 254,
-+ VC4_PACKET_FLUSH = 4,
-+ VC4_PACKET_FLUSH_ALL = 5,
-+ VC4_PACKET_START_TILE_BINNING = 6,
-+ VC4_PACKET_INCREMENT_SEMAPHORE = 7,
-+ VC4_PACKET_WAIT_ON_SEMAPHORE = 8,
-+
-+ VC4_PACKET_BRANCH = 16,
-+ VC4_PACKET_BRANCH_TO_SUB_LIST = 17,
-+
-+ VC4_PACKET_STORE_MS_TILE_BUFFER = 24,
-+ VC4_PACKET_STORE_MS_TILE_BUFFER_AND_EOF = 25,
-+ VC4_PACKET_STORE_FULL_RES_TILE_BUFFER = 26,
-+ VC4_PACKET_LOAD_FULL_RES_TILE_BUFFER = 27,
-+ VC4_PACKET_STORE_TILE_BUFFER_GENERAL = 28,
-+ VC4_PACKET_LOAD_TILE_BUFFER_GENERAL = 29,
-+
-+ VC4_PACKET_GL_INDEXED_PRIMITIVE = 32,
-+ VC4_PACKET_GL_ARRAY_PRIMITIVE = 33,
-+
-+ VC4_PACKET_COMPRESSED_PRIMITIVE = 48,
-+ VC4_PACKET_CLIPPED_COMPRESSED_PRIMITIVE = 49,
-+
-+ VC4_PACKET_PRIMITIVE_LIST_FORMAT = 56,
-+
-+ VC4_PACKET_GL_SHADER_STATE = 64,
-+ VC4_PACKET_NV_SHADER_STATE = 65,
-+ VC4_PACKET_VG_SHADER_STATE = 66,
-+
-+ VC4_PACKET_CONFIGURATION_BITS = 96,
-+ VC4_PACKET_FLAT_SHADE_FLAGS = 97,
-+ VC4_PACKET_POINT_SIZE = 98,
-+ VC4_PACKET_LINE_WIDTH = 99,
-+ VC4_PACKET_RHT_X_BOUNDARY = 100,
-+ VC4_PACKET_DEPTH_OFFSET = 101,
-+ VC4_PACKET_CLIP_WINDOW = 102,
-+ VC4_PACKET_VIEWPORT_OFFSET = 103,
-+ VC4_PACKET_Z_CLIPPING = 104,
-+ VC4_PACKET_CLIPPER_XY_SCALING = 105,
-+ VC4_PACKET_CLIPPER_Z_SCALING = 106,
-+
-+ VC4_PACKET_TILE_BINNING_MODE_CONFIG = 112,
-+ VC4_PACKET_TILE_RENDERING_MODE_CONFIG = 113,
-+ VC4_PACKET_CLEAR_COLORS = 114,
-+ VC4_PACKET_TILE_COORDINATES = 115,
-+
-+ /* Not an actual hardware packet -- this is what we use to put
-+ * references to GEM bos in the command stream, since we need the u32
-+ * int the actual address packet in order to store the offset from the
-+ * start of the BO.
-+ */
-+ VC4_PACKET_GEM_HANDLES = 254,
- } __attribute__ ((__packed__));
-
- #define VC4_PACKET_HALT_SIZE 1
-@@ -148,10 +148,10 @@ enum vc4_packet {
- * VC4_PACKET_LOAD_TILE_BUFFER_GENERAL (low bits of the address)
- */
-
--#define VC4_LOADSTORE_TILE_BUFFER_EOF (1 << 3)
--#define VC4_LOADSTORE_TILE_BUFFER_DISABLE_FULL_VG_MASK (1 << 2)
--#define VC4_LOADSTORE_TILE_BUFFER_DISABLE_FULL_ZS (1 << 1)
--#define VC4_LOADSTORE_TILE_BUFFER_DISABLE_FULL_COLOR (1 << 0)
-+#define VC4_LOADSTORE_TILE_BUFFER_EOF BIT(3)
-+#define VC4_LOADSTORE_TILE_BUFFER_DISABLE_FULL_VG_MASK BIT(2)
-+#define VC4_LOADSTORE_TILE_BUFFER_DISABLE_FULL_ZS BIT(1)
-+#define VC4_LOADSTORE_TILE_BUFFER_DISABLE_FULL_COLOR BIT(0)
-
- /** @} */
-
-@@ -160,10 +160,10 @@ enum vc4_packet {
- * byte 0-1 of VC4_PACKET_STORE_TILE_BUFFER_GENERAL and
- * VC4_PACKET_LOAD_TILE_BUFFER_GENERAL
- */
--#define VC4_STORE_TILE_BUFFER_DISABLE_VG_MASK_CLEAR (1 << 15)
--#define VC4_STORE_TILE_BUFFER_DISABLE_ZS_CLEAR (1 << 14)
--#define VC4_STORE_TILE_BUFFER_DISABLE_COLOR_CLEAR (1 << 13)
--#define VC4_STORE_TILE_BUFFER_DISABLE_SWAP (1 << 12)
-+#define VC4_STORE_TILE_BUFFER_DISABLE_VG_MASK_CLEAR BIT(15)
-+#define VC4_STORE_TILE_BUFFER_DISABLE_ZS_CLEAR BIT(14)
-+#define VC4_STORE_TILE_BUFFER_DISABLE_COLOR_CLEAR BIT(13)
-+#define VC4_STORE_TILE_BUFFER_DISABLE_SWAP BIT(12)
-
- #define VC4_LOADSTORE_TILE_BUFFER_FORMAT_MASK VC4_MASK(9, 8)
- #define VC4_LOADSTORE_TILE_BUFFER_FORMAT_SHIFT 8
-@@ -201,28 +201,28 @@ enum vc4_packet {
- #define VC4_INDEX_BUFFER_U16 (1 << 4)
-
- /* This flag is only present in NV shader state. */
--#define VC4_SHADER_FLAG_SHADED_CLIP_COORDS (1 << 3)
--#define VC4_SHADER_FLAG_ENABLE_CLIPPING (1 << 2)
--#define VC4_SHADER_FLAG_VS_POINT_SIZE (1 << 1)
--#define VC4_SHADER_FLAG_FS_SINGLE_THREAD (1 << 0)
-+#define VC4_SHADER_FLAG_SHADED_CLIP_COORDS BIT(3)
-+#define VC4_SHADER_FLAG_ENABLE_CLIPPING BIT(2)
-+#define VC4_SHADER_FLAG_VS_POINT_SIZE BIT(1)
-+#define VC4_SHADER_FLAG_FS_SINGLE_THREAD BIT(0)
-
- /** @{ byte 2 of config bits. */
--#define VC4_CONFIG_BITS_EARLY_Z_UPDATE (1 << 1)
--#define VC4_CONFIG_BITS_EARLY_Z (1 << 0)
-+#define VC4_CONFIG_BITS_EARLY_Z_UPDATE BIT(1)
-+#define VC4_CONFIG_BITS_EARLY_Z BIT(0)
- /** @} */
-
- /** @{ byte 1 of config bits. */
--#define VC4_CONFIG_BITS_Z_UPDATE (1 << 7)
-+#define VC4_CONFIG_BITS_Z_UPDATE BIT(7)
- /** same values in this 3-bit field as PIPE_FUNC_* */
- #define VC4_CONFIG_BITS_DEPTH_FUNC_SHIFT 4
--#define VC4_CONFIG_BITS_COVERAGE_READ_LEAVE (1 << 3)
-+#define VC4_CONFIG_BITS_COVERAGE_READ_LEAVE BIT(3)
-
- #define VC4_CONFIG_BITS_COVERAGE_UPDATE_NONZERO (0 << 1)
- #define VC4_CONFIG_BITS_COVERAGE_UPDATE_ODD (1 << 1)
- #define VC4_CONFIG_BITS_COVERAGE_UPDATE_OR (2 << 1)
- #define VC4_CONFIG_BITS_COVERAGE_UPDATE_ZERO (3 << 1)
-
--#define VC4_CONFIG_BITS_COVERAGE_PIPE_SELECT (1 << 0)
-+#define VC4_CONFIG_BITS_COVERAGE_PIPE_SELECT BIT(0)
- /** @} */
-
- /** @{ byte 0 of config bits. */
-@@ -230,15 +230,15 @@ enum vc4_packet {
- #define VC4_CONFIG_BITS_RASTERIZER_OVERSAMPLE_4X (1 << 6)
- #define VC4_CONFIG_BITS_RASTERIZER_OVERSAMPLE_16X (2 << 6)
-
--#define VC4_CONFIG_BITS_AA_POINTS_AND_LINES (1 << 4)
--#define VC4_CONFIG_BITS_ENABLE_DEPTH_OFFSET (1 << 3)
--#define VC4_CONFIG_BITS_CW_PRIMITIVES (1 << 2)
--#define VC4_CONFIG_BITS_ENABLE_PRIM_BACK (1 << 1)
--#define VC4_CONFIG_BITS_ENABLE_PRIM_FRONT (1 << 0)
-+#define VC4_CONFIG_BITS_AA_POINTS_AND_LINES BIT(4)
-+#define VC4_CONFIG_BITS_ENABLE_DEPTH_OFFSET BIT(3)
-+#define VC4_CONFIG_BITS_CW_PRIMITIVES BIT(2)
-+#define VC4_CONFIG_BITS_ENABLE_PRIM_BACK BIT(1)
-+#define VC4_CONFIG_BITS_ENABLE_PRIM_FRONT BIT(0)
- /** @} */
-
- /** @{ bits in the last u8 of VC4_PACKET_TILE_BINNING_MODE_CONFIG */
--#define VC4_BIN_CONFIG_DB_NON_MS (1 << 7)
-+#define VC4_BIN_CONFIG_DB_NON_MS BIT(7)
-
- #define VC4_BIN_CONFIG_ALLOC_BLOCK_SIZE_MASK VC4_MASK(6, 5)
- #define VC4_BIN_CONFIG_ALLOC_BLOCK_SIZE_SHIFT 5
-@@ -254,17 +254,17 @@ enum vc4_packet {
- #define VC4_BIN_CONFIG_ALLOC_INIT_BLOCK_SIZE_128 2
- #define VC4_BIN_CONFIG_ALLOC_INIT_BLOCK_SIZE_256 3
-
--#define VC4_BIN_CONFIG_AUTO_INIT_TSDA (1 << 2)
--#define VC4_BIN_CONFIG_TILE_BUFFER_64BIT (1 << 1)
--#define VC4_BIN_CONFIG_MS_MODE_4X (1 << 0)
-+#define VC4_BIN_CONFIG_AUTO_INIT_TSDA BIT(2)
-+#define VC4_BIN_CONFIG_TILE_BUFFER_64BIT BIT(1)
-+#define VC4_BIN_CONFIG_MS_MODE_4X BIT(0)
- /** @} */
-
- /** @{ bits in the last u16 of VC4_PACKET_TILE_RENDERING_MODE_CONFIG */
--#define VC4_RENDER_CONFIG_DB_NON_MS (1 << 12)
--#define VC4_RENDER_CONFIG_EARLY_Z_COVERAGE_DISABLE (1 << 11)
--#define VC4_RENDER_CONFIG_EARLY_Z_DIRECTION_G (1 << 10)
--#define VC4_RENDER_CONFIG_COVERAGE_MODE (1 << 9)
--#define VC4_RENDER_CONFIG_ENABLE_VG_MASK (1 << 8)
-+#define VC4_RENDER_CONFIG_DB_NON_MS BIT(12)
-+#define VC4_RENDER_CONFIG_EARLY_Z_COVERAGE_DISABLE BIT(11)
-+#define VC4_RENDER_CONFIG_EARLY_Z_DIRECTION_G BIT(10)
-+#define VC4_RENDER_CONFIG_COVERAGE_MODE BIT(9)
-+#define VC4_RENDER_CONFIG_ENABLE_VG_MASK BIT(8)
-
- /** The values of the field are VC4_TILING_FORMAT_* */
- #define VC4_RENDER_CONFIG_MEMORY_FORMAT_MASK VC4_MASK(7, 6)
-@@ -280,8 +280,8 @@ enum vc4_packet {
- #define VC4_RENDER_CONFIG_FORMAT_RGBA8888 1
- #define VC4_RENDER_CONFIG_FORMAT_BGR565 2
-
--#define VC4_RENDER_CONFIG_TILE_BUFFER_64BIT (1 << 1)
--#define VC4_RENDER_CONFIG_MS_MODE_4X (1 << 0)
-+#define VC4_RENDER_CONFIG_TILE_BUFFER_64BIT BIT(1)
-+#define VC4_RENDER_CONFIG_MS_MODE_4X BIT(0)
-
- #define VC4_PRIMITIVE_LIST_FORMAT_16_INDEX (1 << 4)
- #define VC4_PRIMITIVE_LIST_FORMAT_32_XY (3 << 4)
-@@ -291,24 +291,24 @@ enum vc4_packet {
- #define VC4_PRIMITIVE_LIST_FORMAT_TYPE_RHT (3 << 0)
-
- enum vc4_texture_data_type {
-- VC4_TEXTURE_TYPE_RGBA8888 = 0,
-- VC4_TEXTURE_TYPE_RGBX8888 = 1,
-- VC4_TEXTURE_TYPE_RGBA4444 = 2,
-- VC4_TEXTURE_TYPE_RGBA5551 = 3,
-- VC4_TEXTURE_TYPE_RGB565 = 4,
-- VC4_TEXTURE_TYPE_LUMINANCE = 5,
-- VC4_TEXTURE_TYPE_ALPHA = 6,
-- VC4_TEXTURE_TYPE_LUMALPHA = 7,
-- VC4_TEXTURE_TYPE_ETC1 = 8,
-- VC4_TEXTURE_TYPE_S16F = 9,
-- VC4_TEXTURE_TYPE_S8 = 10,
-- VC4_TEXTURE_TYPE_S16 = 11,
-- VC4_TEXTURE_TYPE_BW1 = 12,
-- VC4_TEXTURE_TYPE_A4 = 13,
-- VC4_TEXTURE_TYPE_A1 = 14,
-- VC4_TEXTURE_TYPE_RGBA64 = 15,
-- VC4_TEXTURE_TYPE_RGBA32R = 16,
-- VC4_TEXTURE_TYPE_YUV422R = 17,
-+ VC4_TEXTURE_TYPE_RGBA8888 = 0,
-+ VC4_TEXTURE_TYPE_RGBX8888 = 1,
-+ VC4_TEXTURE_TYPE_RGBA4444 = 2,
-+ VC4_TEXTURE_TYPE_RGBA5551 = 3,
-+ VC4_TEXTURE_TYPE_RGB565 = 4,
-+ VC4_TEXTURE_TYPE_LUMINANCE = 5,
-+ VC4_TEXTURE_TYPE_ALPHA = 6,
-+ VC4_TEXTURE_TYPE_LUMALPHA = 7,
-+ VC4_TEXTURE_TYPE_ETC1 = 8,
-+ VC4_TEXTURE_TYPE_S16F = 9,
-+ VC4_TEXTURE_TYPE_S8 = 10,
-+ VC4_TEXTURE_TYPE_S16 = 11,
-+ VC4_TEXTURE_TYPE_BW1 = 12,
-+ VC4_TEXTURE_TYPE_A4 = 13,
-+ VC4_TEXTURE_TYPE_A1 = 14,
-+ VC4_TEXTURE_TYPE_RGBA64 = 15,
-+ VC4_TEXTURE_TYPE_RGBA32R = 16,
-+ VC4_TEXTURE_TYPE_YUV422R = 17,
- };
-
- #define VC4_TEX_P0_OFFSET_MASK VC4_MASK(31, 12)
---- a/drivers/gpu/drm/vc4/vc4_qpu_defines.h
-+++ b/drivers/gpu/drm/vc4/vc4_qpu_defines.h
-@@ -25,194 +25,190 @@
- #define VC4_QPU_DEFINES_H
-
- enum qpu_op_add {
-- QPU_A_NOP,
-- QPU_A_FADD,
-- QPU_A_FSUB,
-- QPU_A_FMIN,
-- QPU_A_FMAX,
-- QPU_A_FMINABS,
-- QPU_A_FMAXABS,
-- QPU_A_FTOI,
-- QPU_A_ITOF,
-- QPU_A_ADD = 12,
-- QPU_A_SUB,
-- QPU_A_SHR,
-- QPU_A_ASR,
-- QPU_A_ROR,
-- QPU_A_SHL,
-- QPU_A_MIN,
-- QPU_A_MAX,
-- QPU_A_AND,
-- QPU_A_OR,
-- QPU_A_XOR,
-- QPU_A_NOT,
-- QPU_A_CLZ,
-- QPU_A_V8ADDS = 30,
-- QPU_A_V8SUBS = 31,
-+ QPU_A_NOP,
-+ QPU_A_FADD,
-+ QPU_A_FSUB,
-+ QPU_A_FMIN,
-+ QPU_A_FMAX,
-+ QPU_A_FMINABS,
-+ QPU_A_FMAXABS,
-+ QPU_A_FTOI,
-+ QPU_A_ITOF,
-+ QPU_A_ADD = 12,
-+ QPU_A_SUB,
-+ QPU_A_SHR,
-+ QPU_A_ASR,
-+ QPU_A_ROR,
-+ QPU_A_SHL,
-+ QPU_A_MIN,
-+ QPU_A_MAX,
-+ QPU_A_AND,
-+ QPU_A_OR,
-+ QPU_A_XOR,
-+ QPU_A_NOT,
-+ QPU_A_CLZ,
-+ QPU_A_V8ADDS = 30,
-+ QPU_A_V8SUBS = 31,
- };
-
- enum qpu_op_mul {
-- QPU_M_NOP,
-- QPU_M_FMUL,
-- QPU_M_MUL24,
-- QPU_M_V8MULD,
-- QPU_M_V8MIN,
-- QPU_M_V8MAX,
-- QPU_M_V8ADDS,
-- QPU_M_V8SUBS,
-+ QPU_M_NOP,
-+ QPU_M_FMUL,
-+ QPU_M_MUL24,
-+ QPU_M_V8MULD,
-+ QPU_M_V8MIN,
-+ QPU_M_V8MAX,
-+ QPU_M_V8ADDS,
-+ QPU_M_V8SUBS,
- };
-
- enum qpu_raddr {
-- QPU_R_FRAG_PAYLOAD_ZW = 15, /* W for A file, Z for B file */
-- /* 0-31 are the plain regfile a or b fields */
-- QPU_R_UNIF = 32,
-- QPU_R_VARY = 35,
-- QPU_R_ELEM_QPU = 38,
-- QPU_R_NOP,
-- QPU_R_XY_PIXEL_COORD = 41,
-- QPU_R_MS_REV_FLAGS = 41,
-- QPU_R_VPM = 48,
-- QPU_R_VPM_LD_BUSY,
-- QPU_R_VPM_LD_WAIT,
-- QPU_R_MUTEX_ACQUIRE,
-+ QPU_R_FRAG_PAYLOAD_ZW = 15, /* W for A file, Z for B file */
-+ /* 0-31 are the plain regfile a or b fields */
-+ QPU_R_UNIF = 32,
-+ QPU_R_VARY = 35,
-+ QPU_R_ELEM_QPU = 38,
-+ QPU_R_NOP,
-+ QPU_R_XY_PIXEL_COORD = 41,
-+ QPU_R_MS_REV_FLAGS = 41,
-+ QPU_R_VPM = 48,
-+ QPU_R_VPM_LD_BUSY,
-+ QPU_R_VPM_LD_WAIT,
-+ QPU_R_MUTEX_ACQUIRE,
- };
-
- enum qpu_waddr {
-- /* 0-31 are the plain regfile a or b fields */
-- QPU_W_ACC0 = 32, /* aka r0 */
-- QPU_W_ACC1,
-- QPU_W_ACC2,
-- QPU_W_ACC3,
-- QPU_W_TMU_NOSWAP,
-- QPU_W_ACC5,
-- QPU_W_HOST_INT,
-- QPU_W_NOP,
-- QPU_W_UNIFORMS_ADDRESS,
-- QPU_W_QUAD_XY, /* X for regfile a, Y for regfile b */
-- QPU_W_MS_FLAGS = 42,
-- QPU_W_REV_FLAG = 42,
-- QPU_W_TLB_STENCIL_SETUP = 43,
-- QPU_W_TLB_Z,
-- QPU_W_TLB_COLOR_MS,
-- QPU_W_TLB_COLOR_ALL,
-- QPU_W_TLB_ALPHA_MASK,
-- QPU_W_VPM,
-- QPU_W_VPMVCD_SETUP, /* LD for regfile a, ST for regfile b */
-- QPU_W_VPM_ADDR, /* LD for regfile a, ST for regfile b */
-- QPU_W_MUTEX_RELEASE,
-- QPU_W_SFU_RECIP,
-- QPU_W_SFU_RECIPSQRT,
-- QPU_W_SFU_EXP,
-- QPU_W_SFU_LOG,
-- QPU_W_TMU0_S,
-- QPU_W_TMU0_T,
-- QPU_W_TMU0_R,
-- QPU_W_TMU0_B,
-- QPU_W_TMU1_S,
-- QPU_W_TMU1_T,
-- QPU_W_TMU1_R,
-- QPU_W_TMU1_B,
-+ /* 0-31 are the plain regfile a or b fields */
-+ QPU_W_ACC0 = 32, /* aka r0 */
-+ QPU_W_ACC1,
-+ QPU_W_ACC2,
-+ QPU_W_ACC3,
-+ QPU_W_TMU_NOSWAP,
-+ QPU_W_ACC5,
-+ QPU_W_HOST_INT,
-+ QPU_W_NOP,
-+ QPU_W_UNIFORMS_ADDRESS,
-+ QPU_W_QUAD_XY, /* X for regfile a, Y for regfile b */
-+ QPU_W_MS_FLAGS = 42,
-+ QPU_W_REV_FLAG = 42,
-+ QPU_W_TLB_STENCIL_SETUP = 43,
-+ QPU_W_TLB_Z,
-+ QPU_W_TLB_COLOR_MS,
-+ QPU_W_TLB_COLOR_ALL,
-+ QPU_W_TLB_ALPHA_MASK,
-+ QPU_W_VPM,
-+ QPU_W_VPMVCD_SETUP, /* LD for regfile a, ST for regfile b */
-+ QPU_W_VPM_ADDR, /* LD for regfile a, ST for regfile b */
-+ QPU_W_MUTEX_RELEASE,
-+ QPU_W_SFU_RECIP,
-+ QPU_W_SFU_RECIPSQRT,
-+ QPU_W_SFU_EXP,
-+ QPU_W_SFU_LOG,
-+ QPU_W_TMU0_S,
-+ QPU_W_TMU0_T,
-+ QPU_W_TMU0_R,
-+ QPU_W_TMU0_B,
-+ QPU_W_TMU1_S,
-+ QPU_W_TMU1_T,
-+ QPU_W_TMU1_R,
-+ QPU_W_TMU1_B,
- };
-
- enum qpu_sig_bits {
-- QPU_SIG_SW_BREAKPOINT,
-- QPU_SIG_NONE,
-- QPU_SIG_THREAD_SWITCH,
-- QPU_SIG_PROG_END,
-- QPU_SIG_WAIT_FOR_SCOREBOARD,
-- QPU_SIG_SCOREBOARD_UNLOCK,
-- QPU_SIG_LAST_THREAD_SWITCH,
-- QPU_SIG_COVERAGE_LOAD,
-- QPU_SIG_COLOR_LOAD,
-- QPU_SIG_COLOR_LOAD_END,
-- QPU_SIG_LOAD_TMU0,
-- QPU_SIG_LOAD_TMU1,
-- QPU_SIG_ALPHA_MASK_LOAD,
-- QPU_SIG_SMALL_IMM,
-- QPU_SIG_LOAD_IMM,
-- QPU_SIG_BRANCH
-+ QPU_SIG_SW_BREAKPOINT,
-+ QPU_SIG_NONE,
-+ QPU_SIG_THREAD_SWITCH,
-+ QPU_SIG_PROG_END,
-+ QPU_SIG_WAIT_FOR_SCOREBOARD,
-+ QPU_SIG_SCOREBOARD_UNLOCK,
-+ QPU_SIG_LAST_THREAD_SWITCH,
-+ QPU_SIG_COVERAGE_LOAD,
-+ QPU_SIG_COLOR_LOAD,
-+ QPU_SIG_COLOR_LOAD_END,
-+ QPU_SIG_LOAD_TMU0,
-+ QPU_SIG_LOAD_TMU1,
-+ QPU_SIG_ALPHA_MASK_LOAD,
-+ QPU_SIG_SMALL_IMM,
-+ QPU_SIG_LOAD_IMM,
-+ QPU_SIG_BRANCH
- };
-
- enum qpu_mux {
-- /* hardware mux values */
-- QPU_MUX_R0,
-- QPU_MUX_R1,
-- QPU_MUX_R2,
-- QPU_MUX_R3,
-- QPU_MUX_R4,
-- QPU_MUX_R5,
-- QPU_MUX_A,
-- QPU_MUX_B,
-+ /* hardware mux values */
-+ QPU_MUX_R0,
-+ QPU_MUX_R1,
-+ QPU_MUX_R2,
-+ QPU_MUX_R3,
-+ QPU_MUX_R4,
-+ QPU_MUX_R5,
-+ QPU_MUX_A,
-+ QPU_MUX_B,
-
-- /* non-hardware mux values */
-- QPU_MUX_IMM,
-+ /* non-hardware mux values */
-+ QPU_MUX_IMM,
- };
-
- enum qpu_cond {
-- QPU_COND_NEVER,
-- QPU_COND_ALWAYS,
-- QPU_COND_ZS,
-- QPU_COND_ZC,
-- QPU_COND_NS,
-- QPU_COND_NC,
-- QPU_COND_CS,
-- QPU_COND_CC,
-+ QPU_COND_NEVER,
-+ QPU_COND_ALWAYS,
-+ QPU_COND_ZS,
-+ QPU_COND_ZC,
-+ QPU_COND_NS,
-+ QPU_COND_NC,
-+ QPU_COND_CS,
-+ QPU_COND_CC,
- };
-
- enum qpu_pack_mul {
-- QPU_PACK_MUL_NOP,
-- QPU_PACK_MUL_8888 = 3, /* replicated to each 8 bits of the 32-bit dst. */
-- QPU_PACK_MUL_8A,
-- QPU_PACK_MUL_8B,
-- QPU_PACK_MUL_8C,
-- QPU_PACK_MUL_8D,
-+ QPU_PACK_MUL_NOP,
-+ /* replicated to each 8 bits of the 32-bit dst. */
-+ QPU_PACK_MUL_8888 = 3,
-+ QPU_PACK_MUL_8A,
-+ QPU_PACK_MUL_8B,
-+ QPU_PACK_MUL_8C,
-+ QPU_PACK_MUL_8D,
- };
-
- enum qpu_pack_a {
-- QPU_PACK_A_NOP,
-- /* convert to 16 bit float if float input, or to int16. */
-- QPU_PACK_A_16A,
-- QPU_PACK_A_16B,
-- /* replicated to each 8 bits of the 32-bit dst. */
-- QPU_PACK_A_8888,
-- /* Convert to 8-bit unsigned int. */
-- QPU_PACK_A_8A,
-- QPU_PACK_A_8B,
-- QPU_PACK_A_8C,
-- QPU_PACK_A_8D,
--
-- /* Saturating variants of the previous instructions. */
-- QPU_PACK_A_32_SAT, /* int-only */
-- QPU_PACK_A_16A_SAT, /* int or float */
-- QPU_PACK_A_16B_SAT,
-- QPU_PACK_A_8888_SAT,
-- QPU_PACK_A_8A_SAT,
-- QPU_PACK_A_8B_SAT,
-- QPU_PACK_A_8C_SAT,
-- QPU_PACK_A_8D_SAT,
-+ QPU_PACK_A_NOP,
-+ /* convert to 16 bit float if float input, or to int16. */
-+ QPU_PACK_A_16A,
-+ QPU_PACK_A_16B,
-+ /* replicated to each 8 bits of the 32-bit dst. */
-+ QPU_PACK_A_8888,
-+ /* Convert to 8-bit unsigned int. */
-+ QPU_PACK_A_8A,
-+ QPU_PACK_A_8B,
-+ QPU_PACK_A_8C,
-+ QPU_PACK_A_8D,
-+
-+ /* Saturating variants of the previous instructions. */
-+ QPU_PACK_A_32_SAT, /* int-only */
-+ QPU_PACK_A_16A_SAT, /* int or float */
-+ QPU_PACK_A_16B_SAT,
-+ QPU_PACK_A_8888_SAT,
-+ QPU_PACK_A_8A_SAT,
-+ QPU_PACK_A_8B_SAT,
-+ QPU_PACK_A_8C_SAT,
-+ QPU_PACK_A_8D_SAT,
- };
-
- enum qpu_unpack_r4 {
-- QPU_UNPACK_R4_NOP,
-- QPU_UNPACK_R4_F16A_TO_F32,
-- QPU_UNPACK_R4_F16B_TO_F32,
-- QPU_UNPACK_R4_8D_REP,
-- QPU_UNPACK_R4_8A,
-- QPU_UNPACK_R4_8B,
-- QPU_UNPACK_R4_8C,
-- QPU_UNPACK_R4_8D,
--};
--
--#define QPU_MASK(high, low) ((((uint64_t)1<<((high)-(low)+1))-1)<<(low))
--/* Using the GNU statement expression extension */
--#define QPU_SET_FIELD(value, field) \
-- ({ \
-- uint64_t fieldval = (uint64_t)(value) << field ## _SHIFT; \
-- assert((fieldval & ~ field ## _MASK) == 0); \
-- fieldval & field ## _MASK; \
-- })
-+ QPU_UNPACK_R4_NOP,
-+ QPU_UNPACK_R4_F16A_TO_F32,
-+ QPU_UNPACK_R4_F16B_TO_F32,
-+ QPU_UNPACK_R4_8D_REP,
-+ QPU_UNPACK_R4_8A,
-+ QPU_UNPACK_R4_8B,
-+ QPU_UNPACK_R4_8C,
-+ QPU_UNPACK_R4_8D,
-+};
-+
-+#define QPU_MASK(high, low) \
-+ ((((uint64_t)1 << ((high) - (low) + 1)) - 1) << (low))
-
--#define QPU_GET_FIELD(word, field) ((uint32_t)(((word) & field ## _MASK) >> field ## _SHIFT))
-+#define QPU_GET_FIELD(word, field) \
-+ ((uint32_t)(((word) & field ## _MASK) >> field ## _SHIFT))
-
- #define QPU_SIG_SHIFT 60
- #define QPU_SIG_MASK QPU_MASK(63, 60)
---- a/drivers/gpu/drm/vc4/vc4_render_cl.c
-+++ b/drivers/gpu/drm/vc4/vc4_render_cl.c
-@@ -63,7 +63,6 @@ static inline void rcl_u32(struct vc4_rc
- setup->next_offset += 4;
- }
-
--
- /*
- * Emits a no-op STORE_TILE_BUFFER_GENERAL.
- *
-@@ -217,7 +216,7 @@ static int vc4_create_rcl_bo(struct drm_
- }
- size += xtiles * ytiles * loop_body_size;
-
-- setup->rcl = &vc4_bo_create(dev, size)->base;
-+ setup->rcl = &vc4_bo_create(dev, size, true)->base;
- if (!setup->rcl)
- return -ENOMEM;
- list_add_tail(&to_vc4_bo(&setup->rcl->base)->unref_head,
-@@ -256,6 +255,7 @@ static int vc4_create_rcl_bo(struct drm_
- for (x = min_x_tile; x <= max_x_tile; x++) {
- bool first = (x == min_x_tile && y == min_y_tile);
- bool last = (x == max_x_tile && y == max_y_tile);
-+
- emit_tile(exec, setup, x, y, first, last);
- }
- }
---- a/drivers/gpu/drm/vc4/vc4_v3d.c
-+++ b/drivers/gpu/drm/vc4/vc4_v3d.c
-@@ -125,7 +125,7 @@ int vc4_v3d_debugfs_regs(struct seq_file
-
- int vc4_v3d_debugfs_ident(struct seq_file *m, void *unused)
- {
-- struct drm_info_node *node = (struct drm_info_node *) m->private;
-+ struct drm_info_node *node = (struct drm_info_node *)m->private;
- struct drm_device *dev = node->minor->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- uint32_t ident1 = V3D_READ(V3D_IDENT1);
-@@ -133,11 +133,13 @@ int vc4_v3d_debugfs_ident(struct seq_fil
- uint32_t tups = VC4_GET_FIELD(ident1, V3D_IDENT1_TUPS);
- uint32_t qups = VC4_GET_FIELD(ident1, V3D_IDENT1_QUPS);
-
-- seq_printf(m, "Revision: %d\n", VC4_GET_FIELD(ident1, V3D_IDENT1_REV));
-+ seq_printf(m, "Revision: %d\n",
-+ VC4_GET_FIELD(ident1, V3D_IDENT1_REV));
- seq_printf(m, "Slices: %d\n", nslc);
- seq_printf(m, "TMUs: %d\n", nslc * tups);
- seq_printf(m, "QPUs: %d\n", nslc * qups);
-- seq_printf(m, "Semaphores: %d\n", VC4_GET_FIELD(ident1, V3D_IDENT1_NSEM));
-+ seq_printf(m, "Semaphores: %d\n",
-+ VC4_GET_FIELD(ident1, V3D_IDENT1_NSEM));
-
- return 0;
- }
-@@ -218,7 +220,7 @@ static int vc4_v3d_bind(struct device *d
- }
-
- static void vc4_v3d_unbind(struct device *dev, struct device *master,
-- void *data)
-+ void *data)
- {
- struct drm_device *drm = dev_get_drvdata(master);
- struct vc4_dev *vc4 = to_vc4_dev(drm);
---- a/drivers/gpu/drm/vc4/vc4_validate.c
-+++ b/drivers/gpu/drm/vc4/vc4_validate.c
-@@ -48,7 +48,6 @@
- void *validated, \
- void *untrusted
-
--
- /** Return the width in pixels of a 64-byte microtile. */
- static uint32_t
- utile_width(int cpp)
-@@ -192,7 +191,7 @@ vc4_check_tex_size(struct vc4_exec_info
-
- if (size + offset < size ||
- size + offset > fbo->base.size) {
-- DRM_ERROR("Overflow in %dx%d (%dx%d) fbo size (%d + %d > %d)\n",
-+ DRM_ERROR("Overflow in %dx%d (%dx%d) fbo size (%d + %d > %zd)\n",
- width, height,
- aligned_width, aligned_height,
- size, offset, fbo->base.size);
-@@ -278,7 +277,7 @@ validate_indexed_prim_list(VALIDATE_ARGS
-
- if (offset > ib->base.size ||
- (ib->base.size - offset) / index_size < length) {
-- DRM_ERROR("IB access overflow (%d + %d*%d > %d)\n",
-+ DRM_ERROR("IB access overflow (%d + %d*%d > %zd)\n",
- offset, length, index_size, ib->base.size);
- return -EINVAL;
- }
-@@ -377,6 +376,7 @@ static int
- validate_tile_binning_config(VALIDATE_ARGS)
- {
- struct drm_device *dev = exec->exec_bo->base.dev;
-+ struct vc4_bo *tile_bo;
- uint8_t flags;
- uint32_t tile_state_size, tile_alloc_size;
- uint32_t tile_count;
-@@ -438,12 +438,12 @@ validate_tile_binning_config(VALIDATE_AR
- */
- tile_alloc_size += 1024 * 1024;
-
-- exec->tile_bo = &vc4_bo_create(dev, exec->tile_alloc_offset +
-- tile_alloc_size)->base;
-+ tile_bo = vc4_bo_create(dev, exec->tile_alloc_offset + tile_alloc_size,
-+ true);
-+ exec->tile_bo = &tile_bo->base;
- if (!exec->tile_bo)
- return -ENOMEM;
-- list_add_tail(&to_vc4_bo(&exec->tile_bo->base)->unref_head,
-- &exec->unref_list);
-+ list_add_tail(&tile_bo->unref_head, &exec->unref_list);
-
- /* tile alloc address. */
- *(uint32_t *)(validated + 0) = (exec->tile_bo->paddr +
-@@ -463,8 +463,8 @@ validate_gem_handles(VALIDATE_ARGS)
- return 0;
- }
-
--#define VC4_DEFINE_PACKET(packet, name, func) \
-- [packet] = { packet ## _SIZE, name, func }
-+#define VC4_DEFINE_PACKET(packet, func) \
-+ [packet] = { packet ## _SIZE, #packet, func }
-
- static const struct cmd_info {
- uint16_t len;
-@@ -472,42 +472,43 @@ static const struct cmd_info {
- int (*func)(struct vc4_exec_info *exec, void *validated,
- void *untrusted);
- } cmd_info[] = {
-- VC4_DEFINE_PACKET(VC4_PACKET_HALT, "halt", NULL),
-- VC4_DEFINE_PACKET(VC4_PACKET_NOP, "nop", NULL),
-- VC4_DEFINE_PACKET(VC4_PACKET_FLUSH, "flush", NULL),
-- VC4_DEFINE_PACKET(VC4_PACKET_FLUSH_ALL, "flush all state", validate_flush_all),
-- VC4_DEFINE_PACKET(VC4_PACKET_START_TILE_BINNING, "start tile binning", validate_start_tile_binning),
-- VC4_DEFINE_PACKET(VC4_PACKET_INCREMENT_SEMAPHORE, "increment semaphore", validate_increment_semaphore),
--
-- VC4_DEFINE_PACKET(VC4_PACKET_GL_INDEXED_PRIMITIVE, "Indexed Primitive List", validate_indexed_prim_list),
--
-- VC4_DEFINE_PACKET(VC4_PACKET_GL_ARRAY_PRIMITIVE, "Vertex Array Primitives", validate_gl_array_primitive),
--
-- /* This is only used by clipped primitives (packets 48 and 49), which
-- * we don't support parsing yet.
-- */
-- VC4_DEFINE_PACKET(VC4_PACKET_PRIMITIVE_LIST_FORMAT, "primitive list format", NULL),
--
-- VC4_DEFINE_PACKET(VC4_PACKET_GL_SHADER_STATE, "GL Shader State", validate_gl_shader_state),
-- VC4_DEFINE_PACKET(VC4_PACKET_NV_SHADER_STATE, "NV Shader State", validate_nv_shader_state),
--
-- VC4_DEFINE_PACKET(VC4_PACKET_CONFIGURATION_BITS, "configuration bits", NULL),
-- VC4_DEFINE_PACKET(VC4_PACKET_FLAT_SHADE_FLAGS, "flat shade flags", NULL),
-- VC4_DEFINE_PACKET(VC4_PACKET_POINT_SIZE, "point size", NULL),
-- VC4_DEFINE_PACKET(VC4_PACKET_LINE_WIDTH, "line width", NULL),
-- VC4_DEFINE_PACKET(VC4_PACKET_RHT_X_BOUNDARY, "RHT X boundary", NULL),
-- VC4_DEFINE_PACKET(VC4_PACKET_DEPTH_OFFSET, "Depth Offset", NULL),
-- VC4_DEFINE_PACKET(VC4_PACKET_CLIP_WINDOW, "Clip Window", NULL),
-- VC4_DEFINE_PACKET(VC4_PACKET_VIEWPORT_OFFSET, "Viewport Offset", NULL),
-- VC4_DEFINE_PACKET(VC4_PACKET_CLIPPER_XY_SCALING, "Clipper XY Scaling", NULL),
-+ VC4_DEFINE_PACKET(VC4_PACKET_HALT, NULL),
-+ VC4_DEFINE_PACKET(VC4_PACKET_NOP, NULL),
-+ VC4_DEFINE_PACKET(VC4_PACKET_FLUSH, NULL),
-+ VC4_DEFINE_PACKET(VC4_PACKET_FLUSH_ALL, validate_flush_all),
-+ VC4_DEFINE_PACKET(VC4_PACKET_START_TILE_BINNING,
-+ validate_start_tile_binning),
-+ VC4_DEFINE_PACKET(VC4_PACKET_INCREMENT_SEMAPHORE,
-+ validate_increment_semaphore),
-+
-+ VC4_DEFINE_PACKET(VC4_PACKET_GL_INDEXED_PRIMITIVE,
-+ validate_indexed_prim_list),
-+ VC4_DEFINE_PACKET(VC4_PACKET_GL_ARRAY_PRIMITIVE,
-+ validate_gl_array_primitive),
-+
-+ VC4_DEFINE_PACKET(VC4_PACKET_PRIMITIVE_LIST_FORMAT, NULL),
-+
-+ VC4_DEFINE_PACKET(VC4_PACKET_GL_SHADER_STATE, validate_gl_shader_state),
-+ VC4_DEFINE_PACKET(VC4_PACKET_NV_SHADER_STATE, validate_nv_shader_state),
-+
-+ VC4_DEFINE_PACKET(VC4_PACKET_CONFIGURATION_BITS, NULL),
-+ VC4_DEFINE_PACKET(VC4_PACKET_FLAT_SHADE_FLAGS, NULL),
-+ VC4_DEFINE_PACKET(VC4_PACKET_POINT_SIZE, NULL),
-+ VC4_DEFINE_PACKET(VC4_PACKET_LINE_WIDTH, NULL),
-+ VC4_DEFINE_PACKET(VC4_PACKET_RHT_X_BOUNDARY, NULL),
-+ VC4_DEFINE_PACKET(VC4_PACKET_DEPTH_OFFSET, NULL),
-+ VC4_DEFINE_PACKET(VC4_PACKET_CLIP_WINDOW, NULL),
-+ VC4_DEFINE_PACKET(VC4_PACKET_VIEWPORT_OFFSET, NULL),
-+ VC4_DEFINE_PACKET(VC4_PACKET_CLIPPER_XY_SCALING, NULL),
- /* Note: The docs say this was also 105, but it was 106 in the
- * initial userland code drop.
- */
-- VC4_DEFINE_PACKET(VC4_PACKET_CLIPPER_Z_SCALING, "Clipper Z Scale and Offset", NULL),
-+ VC4_DEFINE_PACKET(VC4_PACKET_CLIPPER_Z_SCALING, NULL),
-
-- VC4_DEFINE_PACKET(VC4_PACKET_TILE_BINNING_MODE_CONFIG, "tile binning configuration", validate_tile_binning_config),
-+ VC4_DEFINE_PACKET(VC4_PACKET_TILE_BINNING_MODE_CONFIG,
-+ validate_tile_binning_config),
-
-- VC4_DEFINE_PACKET(VC4_PACKET_GEM_HANDLES, "GEM handles", validate_gem_handles),
-+ VC4_DEFINE_PACKET(VC4_PACKET_GEM_HANDLES, validate_gem_handles),
- };
-
- int
-@@ -526,7 +527,7 @@ vc4_validate_bin_cl(struct drm_device *d
- u8 cmd = *(uint8_t *)src_pkt;
- const struct cmd_info *info;
-
-- if (cmd > ARRAY_SIZE(cmd_info)) {
-+ if (cmd >= ARRAY_SIZE(cmd_info)) {
- DRM_ERROR("0x%08x: packet %d out of bounds\n",
- src_offset, cmd);
- return -EINVAL;
-@@ -539,11 +540,6 @@ vc4_validate_bin_cl(struct drm_device *d
- return -EINVAL;
- }
-
--#if 0
-- DRM_INFO("0x%08x: packet %d (%s) size %d processing...\n",
-- src_offset, cmd, info->name, info->len);
--#endif
--
- if (src_offset + info->len > len) {
- DRM_ERROR("0x%08x: packet %d (%s) length 0x%08x "
- "exceeds bounds (0x%08x)\n",
-@@ -558,8 +554,7 @@ vc4_validate_bin_cl(struct drm_device *d
- if (info->func && info->func(exec,
- dst_pkt + 1,
- src_pkt + 1)) {
-- DRM_ERROR("0x%08x: packet %d (%s) failed to "
-- "validate\n",
-+ DRM_ERROR("0x%08x: packet %d (%s) failed to validate\n",
- src_offset, cmd, info->name);
- return -EINVAL;
- }
-@@ -618,12 +613,14 @@ reloc_tex(struct vc4_exec_info *exec,
-
- if (sample->is_direct) {
- uint32_t remaining_size = tex->base.size - p0;
-+
- if (p0 > tex->base.size - 4) {
- DRM_ERROR("UBO offset greater than UBO size\n");
- goto fail;
- }
- if (p1 > remaining_size - 4) {
-- DRM_ERROR("UBO clamp would allow reads outside of UBO\n");
-+ DRM_ERROR("UBO clamp would allow reads "
-+ "outside of UBO\n");
- goto fail;
- }
- *validated_p0 = tex->paddr + p0;
-@@ -786,7 +783,7 @@ validate_shader_rec(struct drm_device *d
- struct drm_gem_cma_object *bo[ARRAY_SIZE(gl_relocs) + 8];
- uint32_t nr_attributes = 0, nr_fixed_relocs, nr_relocs, packet_size;
- int i;
-- struct vc4_validated_shader_info *validated_shader;
-+ struct vc4_validated_shader_info *shader;
-
- if (state->packet == VC4_PACKET_NV_SHADER_STATE) {
- relocs = nv_relocs;
-@@ -841,12 +838,12 @@ validate_shader_rec(struct drm_device *d
- else
- mode = VC4_MODE_RENDER;
-
-- if (!vc4_use_bo(exec, src_handles[i], mode, &bo[i])) {
-+ if (!vc4_use_bo(exec, src_handles[i], mode, &bo[i]))
- return false;
-- }
- }
-
- for (i = 0; i < nr_fixed_relocs; i++) {
-+ struct vc4_bo *vc4_bo;
- uint32_t o = relocs[i].offset;
- uint32_t src_offset = *(uint32_t *)(pkt_u + o);
- uint32_t *texture_handles_u;
-@@ -858,34 +855,34 @@ validate_shader_rec(struct drm_device *d
- switch (relocs[i].type) {
- case RELOC_CODE:
- if (src_offset != 0) {
-- DRM_ERROR("Shaders must be at offset 0 of "
-- "the BO.\n");
-+ DRM_ERROR("Shaders must be at offset 0 "
-+ "of the BO.\n");
- goto fail;
- }
-
-- validated_shader = to_vc4_bo(&bo[i]->base)->validated_shader;
-- if (!validated_shader)
-+ vc4_bo = to_vc4_bo(&bo[i]->base);
-+ shader = vc4_bo->validated_shader;
-+ if (!shader)
- goto fail;
-
-- if (validated_shader->uniforms_src_size >
-- exec->uniforms_size) {
-+ if (shader->uniforms_src_size > exec->uniforms_size) {
- DRM_ERROR("Uniforms src buffer overflow\n");
- goto fail;
- }
-
- texture_handles_u = exec->uniforms_u;
- uniform_data_u = (texture_handles_u +
-- validated_shader->num_texture_samples);
-+ shader->num_texture_samples);
-
- memcpy(exec->uniforms_v, uniform_data_u,
-- validated_shader->uniforms_size);
-+ shader->uniforms_size);
-
- for (tex = 0;
-- tex < validated_shader->num_texture_samples;
-+ tex < shader->num_texture_samples;
- tex++) {
- if (!reloc_tex(exec,
- uniform_data_u,
-- &validated_shader->texture_samples[tex],
-+ &shader->texture_samples[tex],
- texture_handles_u[tex])) {
- goto fail;
- }
-@@ -893,9 +890,9 @@ validate_shader_rec(struct drm_device *d
-
- *(uint32_t *)(pkt_v + o + 4) = exec->uniforms_p;
-
-- exec->uniforms_u += validated_shader->uniforms_src_size;
-- exec->uniforms_v += validated_shader->uniforms_size;
-- exec->uniforms_p += validated_shader->uniforms_size;
-+ exec->uniforms_u += shader->uniforms_src_size;
-+ exec->uniforms_v += shader->uniforms_size;
-+ exec->uniforms_p += shader->uniforms_size;
-
- break;
-
-@@ -926,7 +923,8 @@ validate_shader_rec(struct drm_device *d
- max_index = ((vbo->base.size - offset - attr_size) /
- stride);
- if (state->max_index > max_index) {
-- DRM_ERROR("primitives use index %d out of supplied %d\n",
-+ DRM_ERROR("primitives use index %d out of "
-+ "supplied %d\n",
- state->max_index, max_index);
- return -EINVAL;
- }
---- a/drivers/gpu/drm/vc4/vc4_validate_shaders.c
-+++ b/drivers/gpu/drm/vc4/vc4_validate_shaders.c
-@@ -24,24 +24,16 @@
- /**
- * DOC: Shader validator for VC4.
- *
-- * The VC4 has no IOMMU between it and system memory. So, a user with access
-- * to execute shaders could escalate privilege by overwriting system memory
-- * (using the VPM write address register in the general-purpose DMA mode) or
-- * reading system memory it shouldn't (reading it as a texture, or uniform
-- * data, or vertex data).
-+ * The VC4 has no IOMMU between it and system memory, so a user with
-+ * access to execute shaders could escalate privilege by overwriting
-+ * system memory (using the VPM write address register in the
-+ * general-purpose DMA mode) or reading system memory it shouldn't
-+ * (reading it as a texture, or uniform data, or vertex data).
- *
-- * This walks over a shader starting from some offset within a BO, ensuring
-- * that its accesses are appropriately bounded, and recording how many texture
-- * accesses are made and where so that we can do relocations for them in the
-+ * This walks over a shader BO, ensuring that its accesses are
-+ * appropriately bounded, and recording how many texture accesses are
-+ * made and where so that we can do relocations for them in the
- * uniform stream.
-- *
-- * The kernel API has shaders stored in user-mapped BOs. The BOs will be
-- * forcibly unmapped from the process before validation, and any cache of
-- * validated state will be flushed if the mapping is faulted back in.
-- *
-- * Storing the shaders in BOs means that the validation process will be slow
-- * due to uncached reads, but since shaders are long-lived and shader BOs are
-- * never actually modified, this shouldn't be a problem.
- */
-
- #include "vc4_drv.h"
-@@ -70,7 +62,6 @@ waddr_to_live_reg_index(uint32_t waddr,
- else
- return waddr;
- } else if (waddr <= QPU_W_ACC3) {
--
- return 64 + waddr - QPU_W_ACC0;
- } else {
- return ~0;
-@@ -85,15 +76,14 @@ raddr_add_a_to_live_reg_index(uint64_t i
- uint32_t raddr_a = QPU_GET_FIELD(inst, QPU_RADDR_A);
- uint32_t raddr_b = QPU_GET_FIELD(inst, QPU_RADDR_B);
-
-- if (add_a == QPU_MUX_A) {
-+ if (add_a == QPU_MUX_A)
- return raddr_a;
-- } else if (add_a == QPU_MUX_B && sig != QPU_SIG_SMALL_IMM) {
-+ else if (add_a == QPU_MUX_B && sig != QPU_SIG_SMALL_IMM)
- return 32 + raddr_b;
-- } else if (add_a <= QPU_MUX_R3) {
-+ else if (add_a <= QPU_MUX_R3)
- return 64 + add_a;
-- } else {
-+ else
- return ~0;
-- }
- }
-
- static bool
-@@ -111,9 +101,9 @@ is_tmu_write(uint32_t waddr)
- }
-
- static bool
--record_validated_texture_sample(struct vc4_validated_shader_info *validated_shader,
-- struct vc4_shader_validation_state *validation_state,
-- int tmu)
-+record_texture_sample(struct vc4_validated_shader_info *validated_shader,
-+ struct vc4_shader_validation_state *validation_state,
-+ int tmu)
- {
- uint32_t s = validated_shader->num_texture_samples;
- int i;
-@@ -226,8 +216,8 @@ check_tmu_write(uint64_t inst,
- validated_shader->uniforms_size += 4;
-
- if (submit) {
-- if (!record_validated_texture_sample(validated_shader,
-- validation_state, tmu)) {
-+ if (!record_texture_sample(validated_shader,
-+ validation_state, tmu)) {
- return false;
- }
-
-@@ -238,10 +228,10 @@ check_tmu_write(uint64_t inst,
- }
-
- static bool
--check_register_write(uint64_t inst,
-- struct vc4_validated_shader_info *validated_shader,
-- struct vc4_shader_validation_state *validation_state,
-- bool is_mul)
-+check_reg_write(uint64_t inst,
-+ struct vc4_validated_shader_info *validated_shader,
-+ struct vc4_shader_validation_state *validation_state,
-+ bool is_mul)
- {
- uint32_t waddr = (is_mul ?
- QPU_GET_FIELD(inst, QPU_WADDR_MUL) :
-@@ -297,7 +287,7 @@ check_register_write(uint64_t inst,
- return true;
-
- case QPU_W_TLB_STENCIL_SETUP:
-- return true;
-+ return true;
- }
-
- return true;
-@@ -360,7 +350,7 @@ track_live_clamps(uint64_t inst,
- }
-
- validation_state->live_max_clamp_regs[lri_add] = true;
-- } if (op_add == QPU_A_MIN) {
-+ } else if (op_add == QPU_A_MIN) {
- /* Track live clamps of a value clamped to a minimum of 0 and
- * a maximum of some uniform's offset.
- */
-@@ -392,8 +382,10 @@ check_instruction_writes(uint64_t inst,
- return false;
- }
-
-- ok = (check_register_write(inst, validated_shader, validation_state, false) &&
-- check_register_write(inst, validated_shader, validation_state, true));
-+ ok = (check_reg_write(inst, validated_shader, validation_state,
-+ false) &&
-+ check_reg_write(inst, validated_shader, validation_state,
-+ true));
-
- track_live_clamps(inst, validated_shader, validation_state);
-
-@@ -441,7 +433,7 @@ vc4_validate_shader(struct drm_gem_cma_o
- shader = shader_obj->vaddr;
- max_ip = shader_obj->base.size / sizeof(uint64_t);
-
-- validated_shader = kcalloc(sizeof(*validated_shader), 1, GFP_KERNEL);
-+ validated_shader = kcalloc(1, sizeof(*validated_shader), GFP_KERNEL);
- if (!validated_shader)
- return NULL;
-
-@@ -497,7 +489,7 @@ vc4_validate_shader(struct drm_gem_cma_o
-
- if (ip == max_ip) {
- DRM_ERROR("shader failed to terminate before "
-- "shader BO end at %d\n",
-+ "shader BO end at %zd\n",
- shader_obj->base.size);
- goto fail;
- }
---- a/include/drm/drmP.h
-+++ b/include/drm/drmP.h
-@@ -585,6 +585,13 @@ struct drm_driver {
- int (*gem_open_object) (struct drm_gem_object *, struct drm_file *);
- void (*gem_close_object) (struct drm_gem_object *, struct drm_file *);
-
-+ /**
-+ * Hook for allocating the GEM object struct, for use by core
-+ * helpers.
-+ */
-+ struct drm_gem_object *(*gem_create_object)(struct drm_device *dev,
-+ size_t size);
-+
- /* prime: */
- /* export handle -> fd (see drm_gem_prime_handle_to_fd() helper) */
- int (*prime_handle_to_fd)(struct drm_device *dev, struct drm_file *file_priv,
-@@ -639,7 +646,6 @@ struct drm_driver {
-
- u32 driver_features;
- int dev_priv_size;
-- size_t gem_obj_size;
- const struct drm_ioctl_desc *ioctls;
- int num_ioctls;
- const struct file_operations *fops;
diff --git a/target/linux/brcm2708/patches-4.4/0115-drm-Use-the-driver-s-gem_object_free-function-from-C.patch b/target/linux/brcm2708/patches-4.4/0115-drm-Use-the-driver-s-gem_object_free-function-from-C.patch
deleted file mode 100644
index f6c97e7..0000000
--- a/target/linux/brcm2708/patches-4.4/0115-drm-Use-the-driver-s-gem_object_free-function-from-C.patch
+++ /dev/null
@@ -1,59 +0,0 @@
-From 6b0e19cf6cb9a9edbb0187d398f612e20be1af76 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 11 Dec 2015 19:45:03 -0800
-Subject: [PATCH] drm: Use the driver's gem_object_free function from CMA
- helpers.
-
-VC4 wraps the CMA objects in its own structures, so it needs to do its
-own teardown (waiting for GPU to finish, updating bo_stats tracking).
-The other CMA drivers are using drm_gem_cma_free_object as their
-gem_free_object, so this should be a no-op for them.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/drm_fb_cma_helper.c | 6 +++---
- drivers/gpu/drm/drm_gem_cma_helper.c | 4 ++--
- 2 files changed, 5 insertions(+), 5 deletions(-)
-
---- a/drivers/gpu/drm/drm_fb_cma_helper.c
-+++ b/drivers/gpu/drm/drm_fb_cma_helper.c
-@@ -266,7 +266,7 @@ static int drm_fbdev_cma_create(struct d
- fbi = drm_fb_helper_alloc_fbi(helper);
- if (IS_ERR(fbi)) {
- ret = PTR_ERR(fbi);
-- goto err_drm_gem_cma_free_object;
-+ goto err_gem_free_object;
- }
-
- fbdev_cma->fb = drm_fb_cma_alloc(dev, &mode_cmd, &obj, 1);
-@@ -299,8 +299,8 @@ static int drm_fbdev_cma_create(struct d
-
- err_fb_info_destroy:
- drm_fb_helper_release_fbi(helper);
--err_drm_gem_cma_free_object:
-- drm_gem_cma_free_object(&obj->base);
-+err_gem_free_object:
-+ dev->driver->gem_free_object(&obj->base);
- return ret;
- }
-
---- a/drivers/gpu/drm/drm_gem_cma_helper.c
-+++ b/drivers/gpu/drm/drm_gem_cma_helper.c
-@@ -121,7 +121,7 @@ struct drm_gem_cma_object *drm_gem_cma_c
- return cma_obj;
-
- error:
-- drm_gem_cma_free_object(&cma_obj->base);
-+ drm->driver->gem_free_object(&cma_obj->base);
- return ERR_PTR(ret);
- }
- EXPORT_SYMBOL_GPL(drm_gem_cma_create);
-@@ -171,7 +171,7 @@ drm_gem_cma_create_with_handle(struct dr
- return cma_obj;
-
- err_handle_create:
-- drm_gem_cma_free_object(gem_obj);
-+ drm->driver->gem_free_object(gem_obj);
-
- return ERR_PTR(ret);
- }
diff --git a/target/linux/brcm2708/patches-4.4/0116-drm-vc4-Add-support-for-MSAA-rendering.patch b/target/linux/brcm2708/patches-4.4/0116-drm-vc4-Add-support-for-MSAA-rendering.patch
deleted file mode 100644
index 5e9b8e2..0000000
--- a/target/linux/brcm2708/patches-4.4/0116-drm-vc4-Add-support-for-MSAA-rendering.patch
+++ /dev/null
@@ -1,518 +0,0 @@
-From c5361c444af657e9ac4c50fd92d578ce2e3469b0 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 17 Jul 2015 13:15:50 -0700
-Subject: [PATCH] drm/vc4: Add support for MSAA rendering.
-
-For MSAA, you set a bit in the binner that halves the size of tiles in
-each direction, so you can pack 4 samples per pixel in the tile
-buffer. During rendering, you can load and store raw tile buffer
-contents (to save the per-sample MSAA contents), or you can load/store
-resolved tile buffer contents (loads spam the pixel value to all 4
-samples, and stores either average the 4 color samples, or store the
-first sample for Z/S).
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_packet.h | 23 ++-
- drivers/gpu/drm/vc4/vc4_render_cl.c | 274 ++++++++++++++++++++++++++++++------
- drivers/gpu/drm/vc4/vc4_validate.c | 5 +-
- include/uapi/drm/vc4_drm.h | 11 +-
- 4 files changed, 258 insertions(+), 55 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_packet.h
-+++ b/drivers/gpu/drm/vc4/vc4_packet.h
-@@ -123,6 +123,11 @@ enum vc4_packet {
- #define VC4_PACKET_TILE_COORDINATES_SIZE 3
- #define VC4_PACKET_GEM_HANDLES_SIZE 9
-
-+/* Number of multisamples supported. */
-+#define VC4_MAX_SAMPLES 4
-+/* Size of a full resolution color or Z tile buffer load/store. */
-+#define VC4_TILE_BUFFER_SIZE (64 * 64 * 4)
-+
- /** @{
- * Bits used by packets like VC4_PACKET_STORE_TILE_BUFFER_GENERAL and
- * VC4_PACKET_TILE_RENDERING_MODE_CONFIG.
-@@ -137,10 +142,20 @@ enum vc4_packet {
- * low bits of VC4_PACKET_STORE_FULL_RES_TILE_BUFFER and
- * VC4_PACKET_LOAD_FULL_RES_TILE_BUFFER.
- */
--#define VC4_LOADSTORE_FULL_RES_EOF (1 << 3)
--#define VC4_LOADSTORE_FULL_RES_DISABLE_CLEAR_ALL (1 << 2)
--#define VC4_LOADSTORE_FULL_RES_DISABLE_ZS (1 << 1)
--#define VC4_LOADSTORE_FULL_RES_DISABLE_COLOR (1 << 0)
-+#define VC4_LOADSTORE_FULL_RES_EOF BIT(3)
-+#define VC4_LOADSTORE_FULL_RES_DISABLE_CLEAR_ALL BIT(2)
-+#define VC4_LOADSTORE_FULL_RES_DISABLE_ZS BIT(1)
-+#define VC4_LOADSTORE_FULL_RES_DISABLE_COLOR BIT(0)
-+
-+/** @{
-+ *
-+ * low bits of VC4_PACKET_STORE_FULL_RES_TILE_BUFFER and
-+ * VC4_PACKET_LOAD_FULL_RES_TILE_BUFFER.
-+ */
-+#define VC4_LOADSTORE_FULL_RES_EOF BIT(3)
-+#define VC4_LOADSTORE_FULL_RES_DISABLE_CLEAR_ALL BIT(2)
-+#define VC4_LOADSTORE_FULL_RES_DISABLE_ZS BIT(1)
-+#define VC4_LOADSTORE_FULL_RES_DISABLE_COLOR BIT(0)
-
- /** @{
- *
---- a/drivers/gpu/drm/vc4/vc4_render_cl.c
-+++ b/drivers/gpu/drm/vc4/vc4_render_cl.c
-@@ -37,9 +37,11 @@
-
- struct vc4_rcl_setup {
- struct drm_gem_cma_object *color_read;
-- struct drm_gem_cma_object *color_ms_write;
-+ struct drm_gem_cma_object *color_write;
- struct drm_gem_cma_object *zs_read;
- struct drm_gem_cma_object *zs_write;
-+ struct drm_gem_cma_object *msaa_color_write;
-+ struct drm_gem_cma_object *msaa_zs_write;
-
- struct drm_gem_cma_object *rcl;
- u32 next_offset;
-@@ -82,6 +84,22 @@ static void vc4_store_before_load(struct
- }
-
- /*
-+ * Calculates the physical address of the start of a tile in a RCL surface.
-+ *
-+ * Unlike the other load/store packets,
-+ * VC4_PACKET_LOAD/STORE_FULL_RES_TILE_BUFFER don't look at the tile
-+ * coordinates packet, and instead just store to the address given.
-+ */
-+static uint32_t vc4_full_res_offset(struct vc4_exec_info *exec,
-+ struct drm_gem_cma_object *bo,
-+ struct drm_vc4_submit_rcl_surface *surf,
-+ uint8_t x, uint8_t y)
-+{
-+ return bo->paddr + surf->offset + VC4_TILE_BUFFER_SIZE *
-+ (DIV_ROUND_UP(exec->args->width, 32) * y + x);
-+}
-+
-+/*
- * Emits a PACKET_TILE_COORDINATES if one isn't already pending.
- *
- * The tile coordinates packet triggers a pending load if there is one, are
-@@ -108,22 +126,41 @@ static void emit_tile(struct vc4_exec_in
- * may be outstanding at a time.
- */
- if (setup->color_read) {
-- rcl_u8(setup, VC4_PACKET_LOAD_TILE_BUFFER_GENERAL);
-- rcl_u16(setup, args->color_read.bits);
-- rcl_u32(setup,
-- setup->color_read->paddr + args->color_read.offset);
-+ if (args->color_read.flags &
-+ VC4_SUBMIT_RCL_SURFACE_READ_IS_FULL_RES) {
-+ rcl_u8(setup, VC4_PACKET_LOAD_FULL_RES_TILE_BUFFER);
-+ rcl_u32(setup,
-+ vc4_full_res_offset(exec, setup->color_read,
-+ &args->color_read, x, y) |
-+ VC4_LOADSTORE_FULL_RES_DISABLE_ZS);
-+ } else {
-+ rcl_u8(setup, VC4_PACKET_LOAD_TILE_BUFFER_GENERAL);
-+ rcl_u16(setup, args->color_read.bits);
-+ rcl_u32(setup, setup->color_read->paddr +
-+ args->color_read.offset);
-+ }
- }
-
- if (setup->zs_read) {
-- if (setup->color_read) {
-- /* Exec previous load. */
-- vc4_tile_coordinates(setup, x, y);
-- vc4_store_before_load(setup);
-+ if (args->zs_read.flags &
-+ VC4_SUBMIT_RCL_SURFACE_READ_IS_FULL_RES) {
-+ rcl_u8(setup, VC4_PACKET_LOAD_FULL_RES_TILE_BUFFER);
-+ rcl_u32(setup,
-+ vc4_full_res_offset(exec, setup->zs_read,
-+ &args->zs_read, x, y) |
-+ VC4_LOADSTORE_FULL_RES_DISABLE_COLOR);
-+ } else {
-+ if (setup->color_read) {
-+ /* Exec previous load. */
-+ vc4_tile_coordinates(setup, x, y);
-+ vc4_store_before_load(setup);
-+ }
-+
-+ rcl_u8(setup, VC4_PACKET_LOAD_TILE_BUFFER_GENERAL);
-+ rcl_u16(setup, args->zs_read.bits);
-+ rcl_u32(setup, setup->zs_read->paddr +
-+ args->zs_read.offset);
- }
--
-- rcl_u8(setup, VC4_PACKET_LOAD_TILE_BUFFER_GENERAL);
-- rcl_u16(setup, args->zs_read.bits);
-- rcl_u32(setup, setup->zs_read->paddr + args->zs_read.offset);
- }
-
- /* Clipping depends on tile coordinates having been
-@@ -144,20 +181,60 @@ static void emit_tile(struct vc4_exec_in
- (y * exec->bin_tiles_x + x) * 32));
- }
-
-+ if (setup->msaa_color_write) {
-+ bool last_tile_write = (!setup->msaa_zs_write &&
-+ !setup->zs_write &&
-+ !setup->color_write);
-+ uint32_t bits = VC4_LOADSTORE_FULL_RES_DISABLE_ZS;
-+
-+ if (!last_tile_write)
-+ bits |= VC4_LOADSTORE_FULL_RES_DISABLE_CLEAR_ALL;
-+ else if (last)
-+ bits |= VC4_LOADSTORE_FULL_RES_EOF;
-+ rcl_u8(setup, VC4_PACKET_STORE_FULL_RES_TILE_BUFFER);
-+ rcl_u32(setup,
-+ vc4_full_res_offset(exec, setup->msaa_color_write,
-+ &args->msaa_color_write, x, y) |
-+ bits);
-+ }
-+
-+ if (setup->msaa_zs_write) {
-+ bool last_tile_write = (!setup->zs_write &&
-+ !setup->color_write);
-+ uint32_t bits = VC4_LOADSTORE_FULL_RES_DISABLE_COLOR;
-+
-+ if (setup->msaa_color_write)
-+ vc4_tile_coordinates(setup, x, y);
-+ if (!last_tile_write)
-+ bits |= VC4_LOADSTORE_FULL_RES_DISABLE_CLEAR_ALL;
-+ else if (last)
-+ bits |= VC4_LOADSTORE_FULL_RES_EOF;
-+ rcl_u8(setup, VC4_PACKET_STORE_FULL_RES_TILE_BUFFER);
-+ rcl_u32(setup,
-+ vc4_full_res_offset(exec, setup->msaa_zs_write,
-+ &args->msaa_zs_write, x, y) |
-+ bits);
-+ }
-+
- if (setup->zs_write) {
-+ bool last_tile_write = !setup->color_write;
-+
-+ if (setup->msaa_color_write || setup->msaa_zs_write)
-+ vc4_tile_coordinates(setup, x, y);
-+
- rcl_u8(setup, VC4_PACKET_STORE_TILE_BUFFER_GENERAL);
- rcl_u16(setup, args->zs_write.bits |
-- (setup->color_ms_write ?
-- VC4_STORE_TILE_BUFFER_DISABLE_COLOR_CLEAR : 0));
-+ (last_tile_write ?
-+ 0 : VC4_STORE_TILE_BUFFER_DISABLE_COLOR_CLEAR));
- rcl_u32(setup,
- (setup->zs_write->paddr + args->zs_write.offset) |
-- ((last && !setup->color_ms_write) ?
-+ ((last && last_tile_write) ?
- VC4_LOADSTORE_TILE_BUFFER_EOF : 0));
- }
-
-- if (setup->color_ms_write) {
-- if (setup->zs_write) {
-- /* Reset after previous store */
-+ if (setup->color_write) {
-+ if (setup->msaa_color_write || setup->msaa_zs_write ||
-+ setup->zs_write) {
- vc4_tile_coordinates(setup, x, y);
- }
-
-@@ -192,14 +269,26 @@ static int vc4_create_rcl_bo(struct drm_
- }
-
- if (setup->color_read) {
-- loop_body_size += (VC4_PACKET_LOAD_TILE_BUFFER_GENERAL_SIZE);
-+ if (args->color_read.flags &
-+ VC4_SUBMIT_RCL_SURFACE_READ_IS_FULL_RES) {
-+ loop_body_size += VC4_PACKET_LOAD_FULL_RES_TILE_BUFFER_SIZE;
-+ } else {
-+ loop_body_size += VC4_PACKET_LOAD_TILE_BUFFER_GENERAL_SIZE;
-+ }
- }
- if (setup->zs_read) {
-- if (setup->color_read) {
-- loop_body_size += VC4_PACKET_TILE_COORDINATES_SIZE;
-- loop_body_size += VC4_PACKET_STORE_TILE_BUFFER_GENERAL_SIZE;
-+ if (args->zs_read.flags &
-+ VC4_SUBMIT_RCL_SURFACE_READ_IS_FULL_RES) {
-+ loop_body_size += VC4_PACKET_LOAD_FULL_RES_TILE_BUFFER_SIZE;
-+ } else {
-+ if (setup->color_read &&
-+ !(args->color_read.flags &
-+ VC4_SUBMIT_RCL_SURFACE_READ_IS_FULL_RES)) {
-+ loop_body_size += VC4_PACKET_TILE_COORDINATES_SIZE;
-+ loop_body_size += VC4_PACKET_STORE_TILE_BUFFER_GENERAL_SIZE;
-+ }
-+ loop_body_size += VC4_PACKET_LOAD_TILE_BUFFER_GENERAL_SIZE;
- }
-- loop_body_size += VC4_PACKET_LOAD_TILE_BUFFER_GENERAL_SIZE;
- }
-
- if (has_bin) {
-@@ -207,13 +296,23 @@ static int vc4_create_rcl_bo(struct drm_
- loop_body_size += VC4_PACKET_BRANCH_TO_SUB_LIST_SIZE;
- }
-
-+ if (setup->msaa_color_write)
-+ loop_body_size += VC4_PACKET_STORE_FULL_RES_TILE_BUFFER_SIZE;
-+ if (setup->msaa_zs_write)
-+ loop_body_size += VC4_PACKET_STORE_FULL_RES_TILE_BUFFER_SIZE;
-+
- if (setup->zs_write)
- loop_body_size += VC4_PACKET_STORE_TILE_BUFFER_GENERAL_SIZE;
-- if (setup->color_ms_write) {
-- if (setup->zs_write)
-- loop_body_size += VC4_PACKET_TILE_COORDINATES_SIZE;
-+ if (setup->color_write)
- loop_body_size += VC4_PACKET_STORE_MS_TILE_BUFFER_SIZE;
-- }
-+
-+ /* We need a VC4_PACKET_TILE_COORDINATES in between each store. */
-+ loop_body_size += VC4_PACKET_TILE_COORDINATES_SIZE *
-+ ((setup->msaa_color_write != NULL) +
-+ (setup->msaa_zs_write != NULL) +
-+ (setup->color_write != NULL) +
-+ (setup->zs_write != NULL) - 1);
-+
- size += xtiles * ytiles * loop_body_size;
-
- setup->rcl = &vc4_bo_create(dev, size, true)->base;
-@@ -224,13 +323,12 @@ static int vc4_create_rcl_bo(struct drm_
-
- rcl_u8(setup, VC4_PACKET_TILE_RENDERING_MODE_CONFIG);
- rcl_u32(setup,
-- (setup->color_ms_write ?
-- (setup->color_ms_write->paddr +
-- args->color_ms_write.offset) :
-+ (setup->color_write ? (setup->color_write->paddr +
-+ args->color_write.offset) :
- 0));
- rcl_u16(setup, args->width);
- rcl_u16(setup, args->height);
-- rcl_u16(setup, args->color_ms_write.bits);
-+ rcl_u16(setup, args->color_write.bits);
-
- /* The tile buffer gets cleared when the previous tile is stored. If
- * the clear values changed between frames, then the tile buffer has
-@@ -267,6 +365,56 @@ static int vc4_create_rcl_bo(struct drm_
- return 0;
- }
-
-+static int vc4_full_res_bounds_check(struct vc4_exec_info *exec,
-+ struct drm_gem_cma_object *obj,
-+ struct drm_vc4_submit_rcl_surface *surf)
-+{
-+ struct drm_vc4_submit_cl *args = exec->args;
-+ u32 render_tiles_stride = DIV_ROUND_UP(exec->args->width, 32);
-+
-+ if (surf->offset > obj->base.size) {
-+ DRM_ERROR("surface offset %d > BO size %zd\n",
-+ surf->offset, obj->base.size);
-+ return -EINVAL;
-+ }
-+
-+ if ((obj->base.size - surf->offset) / VC4_TILE_BUFFER_SIZE <
-+ render_tiles_stride * args->max_y_tile + args->max_x_tile) {
-+ DRM_ERROR("MSAA tile %d, %d out of bounds "
-+ "(bo size %zd, offset %d).\n",
-+ args->max_x_tile, args->max_y_tile,
-+ obj->base.size,
-+ surf->offset);
-+ return -EINVAL;
-+ }
-+
-+ return 0;
-+}
-+
-+static int vc4_rcl_msaa_surface_setup(struct vc4_exec_info *exec,
-+ struct drm_gem_cma_object **obj,
-+ struct drm_vc4_submit_rcl_surface *surf)
-+{
-+ if (surf->flags != 0 || surf->bits != 0) {
-+ DRM_ERROR("MSAA surface had nonzero flags/bits\n");
-+ return -EINVAL;
-+ }
-+
-+ if (surf->hindex == ~0)
-+ return 0;
-+
-+ *obj = vc4_use_bo(exec, surf->hindex);
-+ if (!*obj)
-+ return -EINVAL;
-+
-+ if (surf->offset & 0xf) {
-+ DRM_ERROR("MSAA write must be 16b aligned.\n");
-+ return -EINVAL;
-+ }
-+
-+ return vc4_full_res_bounds_check(exec, *obj, surf);
-+}
-+
- static int vc4_rcl_surface_setup(struct vc4_exec_info *exec,
- struct drm_gem_cma_object **obj,
- struct drm_vc4_submit_rcl_surface *surf)
-@@ -278,9 +426,10 @@ static int vc4_rcl_surface_setup(struct
- uint8_t format = VC4_GET_FIELD(surf->bits,
- VC4_LOADSTORE_TILE_BUFFER_FORMAT);
- int cpp;
-+ int ret;
-
-- if (surf->pad != 0) {
-- DRM_ERROR("Padding unset\n");
-+ if (surf->flags & ~VC4_SUBMIT_RCL_SURFACE_READ_IS_FULL_RES) {
-+ DRM_ERROR("Extra flags set\n");
- return -EINVAL;
- }
-
-@@ -290,6 +439,25 @@ static int vc4_rcl_surface_setup(struct
- if (!vc4_use_bo(exec, surf->hindex, VC4_MODE_RENDER, obj))
- return -EINVAL;
-
-+ if (surf->flags & VC4_SUBMIT_RCL_SURFACE_READ_IS_FULL_RES) {
-+ if (surf == &exec->args->zs_write) {
-+ DRM_ERROR("general zs write may not be a full-res.\n");
-+ return -EINVAL;
-+ }
-+
-+ if (surf->bits != 0) {
-+ DRM_ERROR("load/store general bits set with "
-+ "full res load/store.\n");
-+ return -EINVAL;
-+ }
-+
-+ ret = vc4_full_res_bounds_check(exec, *obj, surf);
-+ if (!ret)
-+ return ret;
-+
-+ return 0;
-+ }
-+
- if (surf->bits & ~(VC4_LOADSTORE_TILE_BUFFER_TILING_MASK |
- VC4_LOADSTORE_TILE_BUFFER_BUFFER_MASK |
- VC4_LOADSTORE_TILE_BUFFER_FORMAT_MASK)) {
-@@ -341,9 +509,10 @@ static int vc4_rcl_surface_setup(struct
- }
-
- static int
--vc4_rcl_ms_surface_setup(struct vc4_exec_info *exec,
-- struct drm_gem_cma_object **obj,
-- struct drm_vc4_submit_rcl_surface *surf)
-+vc4_rcl_render_config_surface_setup(struct vc4_exec_info *exec,
-+ struct vc4_rcl_setup *setup,
-+ struct drm_gem_cma_object **obj,
-+ struct drm_vc4_submit_rcl_surface *surf)
- {
- uint8_t tiling = VC4_GET_FIELD(surf->bits,
- VC4_RENDER_CONFIG_MEMORY_FORMAT);
-@@ -351,13 +520,15 @@ vc4_rcl_ms_surface_setup(struct vc4_exec
- VC4_RENDER_CONFIG_FORMAT);
- int cpp;
-
-- if (surf->pad != 0) {
-- DRM_ERROR("Padding unset\n");
-+ if (surf->flags != 0) {
-+ DRM_ERROR("No flags supported on render config.\n");
- return -EINVAL;
- }
-
- if (surf->bits & ~(VC4_RENDER_CONFIG_MEMORY_FORMAT_MASK |
-- VC4_RENDER_CONFIG_FORMAT_MASK)) {
-+ VC4_RENDER_CONFIG_FORMAT_MASK |
-+ VC4_RENDER_CONFIG_MS_MODE_4X |
-+ VC4_RENDER_CONFIG_DECIMATE_MODE_4X)) {
- DRM_ERROR("Unknown bits in render config: 0x%04x\n",
- surf->bits);
- return -EINVAL;
-@@ -413,18 +584,20 @@ int vc4_get_rcl(struct drm_device *dev,
- if (has_bin &&
- (args->max_x_tile > exec->bin_tiles_x ||
- args->max_y_tile > exec->bin_tiles_y)) {
-- DRM_ERROR("Render tiles (%d,%d) outside of bin config (%d,%d)\n",
-+ DRM_ERROR("Render tiles (%d,%d) outside of bin config "
-+ "(%d,%d)\n",
- args->max_x_tile, args->max_y_tile,
- exec->bin_tiles_x, exec->bin_tiles_y);
- return -EINVAL;
- }
-
-- ret = vc4_rcl_surface_setup(exec, &setup.color_read, &args->color_read);
-+ ret = vc4_rcl_render_config_surface_setup(exec, &setup,
-+ &setup.color_write,
-+ &args->color_write);
- if (ret)
- return ret;
-
-- ret = vc4_rcl_ms_surface_setup(exec, &setup.color_ms_write,
-- &args->color_ms_write);
-+ ret = vc4_rcl_surface_setup(exec, &setup.color_read, &args->color_read);
- if (ret)
- return ret;
-
-@@ -436,10 +609,21 @@ int vc4_get_rcl(struct drm_device *dev,
- if (ret)
- return ret;
-
-+ ret = vc4_rcl_msaa_surface_setup(exec, &setup.msaa_color_write,
-+ &args->msaa_color_write);
-+ if (ret)
-+ return ret;
-+
-+ ret = vc4_rcl_msaa_surface_setup(exec, &setup.msaa_zs_write,
-+ &args->msaa_zs_write);
-+ if (ret)
-+ return ret;
-+
- /* We shouldn't even have the job submitted to us if there's no
- * surface to write out.
- */
-- if (!setup.color_ms_write && !setup.zs_write) {
-+ if (!setup.color_write && !setup.zs_write &&
-+ !setup.msaa_color_write && !setup.msaa_zs_write) {
- DRM_ERROR("RCL requires color or Z/S write\n");
- return -EINVAL;
- }
---- a/drivers/gpu/drm/vc4/vc4_validate.c
-+++ b/drivers/gpu/drm/vc4/vc4_validate.c
-@@ -400,9 +400,8 @@ validate_tile_binning_config(VALIDATE_AR
- }
-
- if (flags & (VC4_BIN_CONFIG_DB_NON_MS |
-- VC4_BIN_CONFIG_TILE_BUFFER_64BIT |
-- VC4_BIN_CONFIG_MS_MODE_4X)) {
-- DRM_ERROR("unsupported bining config flags 0x%02x\n", flags);
-+ VC4_BIN_CONFIG_TILE_BUFFER_64BIT)) {
-+ DRM_ERROR("unsupported binning config flags 0x%02x\n", flags);
- return -EINVAL;
- }
-
---- a/include/uapi/drm/vc4_drm.h
-+++ b/include/uapi/drm/vc4_drm.h
-@@ -46,10 +46,13 @@ struct drm_vc4_submit_rcl_surface {
- uint32_t hindex; /* Handle index, or ~0 if not present. */
- uint32_t offset; /* Offset to start of buffer. */
- /*
-- * Bits for either render config (color_ms_write) or load/store packet.
-+ * Bits for either render config (color_write) or load/store packet.
-+ * Bits should all be 0 for MSAA load/stores.
- */
- uint16_t bits;
-- uint16_t pad;
-+
-+#define VC4_SUBMIT_RCL_SURFACE_READ_IS_FULL_RES (1 << 0)
-+ uint16_t flags;
- };
-
- /**
-@@ -128,9 +131,11 @@ struct drm_vc4_submit_cl {
- uint8_t max_x_tile;
- uint8_t max_y_tile;
- struct drm_vc4_submit_rcl_surface color_read;
-- struct drm_vc4_submit_rcl_surface color_ms_write;
-+ struct drm_vc4_submit_rcl_surface color_write;
- struct drm_vc4_submit_rcl_surface zs_read;
- struct drm_vc4_submit_rcl_surface zs_write;
-+ struct drm_vc4_submit_rcl_surface msaa_color_write;
-+ struct drm_vc4_submit_rcl_surface msaa_zs_write;
- uint32_t clear_color[2];
- uint32_t clear_z;
- uint8_t clear_s;
diff --git a/target/linux/brcm2708/patches-4.4/0117-drm-vc4-A-few-more-non-functional-changes-to-sync-to.patch b/target/linux/brcm2708/patches-4.4/0117-drm-vc4-A-few-more-non-functional-changes-to-sync-to.patch
deleted file mode 100644
index 75128a7..0000000
--- a/target/linux/brcm2708/patches-4.4/0117-drm-vc4-A-few-more-non-functional-changes-to-sync-to.patch
+++ /dev/null
@@ -1,345 +0,0 @@
-From 610288fc950dc72015acee534573cfdb398c48d2 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 8 Dec 2015 14:00:43 -0800
-Subject: [PATCH] drm/vc4: A few more non-functional changes to sync to
- upstream.
-
-At this point all that's left is the force-enable of HDMI connector,
-and using direct firmware calls to turn on V3D instead of the generic
-power domain support.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_v3d.c | 2 +-
- include/uapi/drm/vc4_drm.h | 182 +++++++++++++++++++++---------------------
- 2 files changed, 92 insertions(+), 92 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_v3d.c
-+++ b/drivers/gpu/drm/vc4/vc4_v3d.c
-@@ -109,7 +109,7 @@ static const struct {
-
- int vc4_v3d_debugfs_regs(struct seq_file *m, void *unused)
- {
-- struct drm_info_node *node = (struct drm_info_node *) m->private;
-+ struct drm_info_node *node = (struct drm_info_node *)m->private;
- struct drm_device *dev = node->minor->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- int i;
---- a/include/uapi/drm/vc4_drm.h
-+++ b/include/uapi/drm/vc4_drm.h
-@@ -24,7 +24,7 @@
- #ifndef _UAPI_VC4_DRM_H_
- #define _UAPI_VC4_DRM_H_
-
--#include <drm/drm.h>
-+#include "drm.h"
-
- #define DRM_VC4_SUBMIT_CL 0x00
- #define DRM_VC4_WAIT_SEQNO 0x01
-@@ -34,25 +34,25 @@
- #define DRM_VC4_CREATE_SHADER_BO 0x05
- #define DRM_VC4_GET_HANG_STATE 0x06
-
--#define DRM_IOCTL_VC4_SUBMIT_CL DRM_IOWR( DRM_COMMAND_BASE + DRM_VC4_SUBMIT_CL, struct drm_vc4_submit_cl)
--#define DRM_IOCTL_VC4_WAIT_SEQNO DRM_IOWR( DRM_COMMAND_BASE + DRM_VC4_WAIT_SEQNO, struct drm_vc4_wait_seqno)
--#define DRM_IOCTL_VC4_WAIT_BO DRM_IOWR( DRM_COMMAND_BASE + DRM_VC4_WAIT_BO, struct drm_vc4_wait_bo)
--#define DRM_IOCTL_VC4_CREATE_BO DRM_IOWR( DRM_COMMAND_BASE + DRM_VC4_CREATE_BO, struct drm_vc4_create_bo)
--#define DRM_IOCTL_VC4_MMAP_BO DRM_IOWR( DRM_COMMAND_BASE + DRM_VC4_MMAP_BO, struct drm_vc4_mmap_bo)
--#define DRM_IOCTL_VC4_CREATE_SHADER_BO DRM_IOWR( DRM_COMMAND_BASE + DRM_VC4_CREATE_SHADER_BO, struct drm_vc4_create_shader_bo)
--#define DRM_IOCTL_VC4_GET_HANG_STATE DRM_IOWR( DRM_COMMAND_BASE + DRM_VC4_GET_HANG_STATE, struct drm_vc4_get_hang_state)
-+#define DRM_IOCTL_VC4_SUBMIT_CL DRM_IOWR(DRM_COMMAND_BASE + DRM_VC4_SUBMIT_CL, struct drm_vc4_submit_cl)
-+#define DRM_IOCTL_VC4_WAIT_SEQNO DRM_IOWR(DRM_COMMAND_BASE + DRM_VC4_WAIT_SEQNO, struct drm_vc4_wait_seqno)
-+#define DRM_IOCTL_VC4_WAIT_BO DRM_IOWR(DRM_COMMAND_BASE + DRM_VC4_WAIT_BO, struct drm_vc4_wait_bo)
-+#define DRM_IOCTL_VC4_CREATE_BO DRM_IOWR(DRM_COMMAND_BASE + DRM_VC4_CREATE_BO, struct drm_vc4_create_bo)
-+#define DRM_IOCTL_VC4_MMAP_BO DRM_IOWR(DRM_COMMAND_BASE + DRM_VC4_MMAP_BO, struct drm_vc4_mmap_bo)
-+#define DRM_IOCTL_VC4_CREATE_SHADER_BO DRM_IOWR(DRM_COMMAND_BASE + DRM_VC4_CREATE_SHADER_BO, struct drm_vc4_create_shader_bo)
-+#define DRM_IOCTL_VC4_GET_HANG_STATE DRM_IOWR(DRM_COMMAND_BASE + DRM_VC4_GET_HANG_STATE, struct drm_vc4_get_hang_state)
-
- struct drm_vc4_submit_rcl_surface {
-- uint32_t hindex; /* Handle index, or ~0 if not present. */
-- uint32_t offset; /* Offset to start of buffer. */
-+ __u32 hindex; /* Handle index, or ~0 if not present. */
-+ __u32 offset; /* Offset to start of buffer. */
- /*
-- * Bits for either render config (color_write) or load/store packet.
-- * Bits should all be 0 for MSAA load/stores.
-+ * Bits for either render config (color_write) or load/store packet.
-+ * Bits should all be 0 for MSAA load/stores.
- */
-- uint16_t bits;
-+ __u16 bits;
-
- #define VC4_SUBMIT_RCL_SURFACE_READ_IS_FULL_RES (1 << 0)
-- uint16_t flags;
-+ __u16 flags;
- };
-
- /**
-@@ -76,7 +76,7 @@ struct drm_vc4_submit_cl {
- * then writes out the state updates and draw calls necessary per tile
- * to the tile allocation BO.
- */
-- uint64_t bin_cl;
-+ __u64 bin_cl;
-
- /* Pointer to the shader records.
- *
-@@ -85,16 +85,16 @@ struct drm_vc4_submit_cl {
- * reference to the shader record has enough information to determine
- * how many pointers are necessary (fixed number for shaders/uniforms,
- * and an attribute count), so those BO indices into bo_handles are
-- * just stored as uint32_ts before each shader record passed in.
-+ * just stored as __u32s before each shader record passed in.
- */
-- uint64_t shader_rec;
-+ __u64 shader_rec;
-
- /* Pointer to uniform data and texture handles for the textures
- * referenced by the shader.
- *
- * For each shader state record, there is a set of uniform data in the
- * order referenced by the record (FS, VS, then CS). Each set of
-- * uniform data has a uint32_t index into bo_handles per texture
-+ * uniform data has a __u32 index into bo_handles per texture
- * sample operation, in the order the QPU_W_TMUn_S writes appear in
- * the program. Following the texture BO handle indices is the actual
- * uniform data.
-@@ -103,52 +103,52 @@ struct drm_vc4_submit_cl {
- * because the kernel has to determine the sizes anyway during shader
- * code validation.
- */
-- uint64_t uniforms;
-- uint64_t bo_handles;
-+ __u64 uniforms;
-+ __u64 bo_handles;
-
- /* Size in bytes of the binner command list. */
-- uint32_t bin_cl_size;
-+ __u32 bin_cl_size;
- /* Size in bytes of the set of shader records. */
-- uint32_t shader_rec_size;
-+ __u32 shader_rec_size;
- /* Number of shader records.
- *
- * This could just be computed from the contents of shader_records and
- * the address bits of references to them from the bin CL, but it
- * keeps the kernel from having to resize some allocations it makes.
- */
-- uint32_t shader_rec_count;
-+ __u32 shader_rec_count;
- /* Size in bytes of the uniform state. */
-- uint32_t uniforms_size;
-+ __u32 uniforms_size;
-
- /* Number of BO handles passed in (size is that times 4). */
-- uint32_t bo_handle_count;
-+ __u32 bo_handle_count;
-
- /* RCL setup: */
-- uint16_t width;
-- uint16_t height;
-- uint8_t min_x_tile;
-- uint8_t min_y_tile;
-- uint8_t max_x_tile;
-- uint8_t max_y_tile;
-+ __u16 width;
-+ __u16 height;
-+ __u8 min_x_tile;
-+ __u8 min_y_tile;
-+ __u8 max_x_tile;
-+ __u8 max_y_tile;
- struct drm_vc4_submit_rcl_surface color_read;
- struct drm_vc4_submit_rcl_surface color_write;
- struct drm_vc4_submit_rcl_surface zs_read;
- struct drm_vc4_submit_rcl_surface zs_write;
- struct drm_vc4_submit_rcl_surface msaa_color_write;
- struct drm_vc4_submit_rcl_surface msaa_zs_write;
-- uint32_t clear_color[2];
-- uint32_t clear_z;
-- uint8_t clear_s;
-+ __u32 clear_color[2];
-+ __u32 clear_z;
-+ __u8 clear_s;
-
-- uint32_t pad:24;
-+ __u32 pad:24;
-
- #define VC4_SUBMIT_CL_USE_CLEAR_COLOR (1 << 0)
-- uint32_t flags;
-+ __u32 flags;
-
- /* Returned value of the seqno of this render job (for the
- * wait ioctl).
- */
-- uint64_t seqno;
-+ __u64 seqno;
- };
-
- /**
-@@ -159,8 +159,8 @@ struct drm_vc4_submit_cl {
- * block, just return the status."
- */
- struct drm_vc4_wait_seqno {
-- uint64_t seqno;
-- uint64_t timeout_ns;
-+ __u64 seqno;
-+ __u64 timeout_ns;
- };
-
- /**
-@@ -172,9 +172,9 @@ struct drm_vc4_wait_seqno {
- * completed.
- */
- struct drm_vc4_wait_bo {
-- uint32_t handle;
-- uint32_t pad;
-- uint64_t timeout_ns;
-+ __u32 handle;
-+ __u32 pad;
-+ __u64 timeout_ns;
- };
-
- /**
-@@ -184,11 +184,30 @@ struct drm_vc4_wait_bo {
- * used in a future extension.
- */
- struct drm_vc4_create_bo {
-- uint32_t size;
-- uint32_t flags;
-+ __u32 size;
-+ __u32 flags;
- /** Returned GEM handle for the BO. */
-- uint32_t handle;
-- uint32_t pad;
-+ __u32 handle;
-+ __u32 pad;
-+};
-+
-+/**
-+ * struct drm_vc4_mmap_bo - ioctl argument for mapping VC4 BOs.
-+ *
-+ * This doesn't actually perform an mmap. Instead, it returns the
-+ * offset you need to use in an mmap on the DRM device node. This
-+ * means that tools like valgrind end up knowing about the mapped
-+ * memory.
-+ *
-+ * There are currently no values for the flags argument, but it may be
-+ * used in a future extension.
-+ */
-+struct drm_vc4_mmap_bo {
-+ /** Handle for the object being mapped. */
-+ __u32 handle;
-+ __u32 flags;
-+ /** offset into the drm node to use for subsequent mmap call. */
-+ __u64 offset;
- };
-
- /**
-@@ -201,43 +220,24 @@ struct drm_vc4_create_bo {
- */
- struct drm_vc4_create_shader_bo {
- /* Size of the data argument. */
-- uint32_t size;
-+ __u32 size;
- /* Flags, currently must be 0. */
-- uint32_t flags;
-+ __u32 flags;
-
- /* Pointer to the data. */
-- uint64_t data;
-+ __u64 data;
-
- /** Returned GEM handle for the BO. */
-- uint32_t handle;
-+ __u32 handle;
- /* Pad, must be 0. */
-- uint32_t pad;
--};
--
--/**
-- * struct drm_vc4_mmap_bo - ioctl argument for mapping VC4 BOs.
-- *
-- * This doesn't actually perform an mmap. Instead, it returns the
-- * offset you need to use in an mmap on the DRM device node. This
-- * means that tools like valgrind end up knowing about the mapped
-- * memory.
-- *
-- * There are currently no values for the flags argument, but it may be
-- * used in a future extension.
-- */
--struct drm_vc4_mmap_bo {
-- /** Handle for the object being mapped. */
-- uint32_t handle;
-- uint32_t flags;
-- /** offset into the drm node to use for subsequent mmap call. */
-- uint64_t offset;
-+ __u32 pad;
- };
-
- struct drm_vc4_get_hang_state_bo {
-- uint32_t handle;
-- uint32_t paddr;
-- uint32_t size;
-- uint32_t pad;
-+ __u32 handle;
-+ __u32 paddr;
-+ __u32 size;
-+ __u32 pad;
- };
-
- /**
-@@ -246,34 +246,34 @@ struct drm_vc4_get_hang_state_bo {
- */
- struct drm_vc4_get_hang_state {
- /** Pointer to array of struct drm_vc4_get_hang_state_bo. */
-- uint64_t bo;
-+ __u64 bo;
- /**
- * On input, the size of the bo array. Output is the number
- * of bos to be returned.
- */
-- uint32_t bo_count;
-+ __u32 bo_count;
-
-- uint32_t start_bin, start_render;
-+ __u32 start_bin, start_render;
-
-- uint32_t ct0ca, ct0ea;
-- uint32_t ct1ca, ct1ea;
-- uint32_t ct0cs, ct1cs;
-- uint32_t ct0ra0, ct1ra0;
--
-- uint32_t bpca, bpcs;
-- uint32_t bpoa, bpos;
--
-- uint32_t vpmbase;
--
-- uint32_t dbge;
-- uint32_t fdbgo;
-- uint32_t fdbgb;
-- uint32_t fdbgr;
-- uint32_t fdbgs;
-- uint32_t errstat;
-+ __u32 ct0ca, ct0ea;
-+ __u32 ct1ca, ct1ea;
-+ __u32 ct0cs, ct1cs;
-+ __u32 ct0ra0, ct1ra0;
-+
-+ __u32 bpca, bpcs;
-+ __u32 bpoa, bpos;
-+
-+ __u32 vpmbase;
-+
-+ __u32 dbge;
-+ __u32 fdbgo;
-+ __u32 fdbgb;
-+ __u32 fdbgr;
-+ __u32 fdbgs;
-+ __u32 errstat;
-
- /* Pad that we may save more registers into in the future. */
-- uint32_t pad[16];
-+ __u32 pad[16];
- };
-
- #endif /* _UAPI_VC4_DRM_H_ */
diff --git a/target/linux/brcm2708/patches-4.4/0118-drm-vc4-Use-hpd-gpios-for-HDMI-GPIO-like-what-landed.patch b/target/linux/brcm2708/patches-4.4/0118-drm-vc4-Use-hpd-gpios-for-HDMI-GPIO-like-what-landed.patch
deleted file mode 100644
index 95f764b..0000000
--- a/target/linux/brcm2708/patches-4.4/0118-drm-vc4-Use-hpd-gpios-for-HDMI-GPIO-like-what-landed.patch
+++ /dev/null
@@ -1,22 +0,0 @@
-From a55db42f8e9a6451db116a45d6e69ea22495a577 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 15 Dec 2015 23:46:32 +0000
-Subject: [PATCH] drm/vc4: Use "hpd-gpios" for HDMI GPIO, like what landed
- upstream.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts
-@@ -68,7 +68,7 @@
- <0x7e808000 0x100>;
- interrupts = <2 8>, <2 9>;
- ddc = <&i2c2>;
-- hpd-gpio = <&gpio 46 GPIO_ACTIVE_HIGH>;
-+ hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
- clocks = <&cprman BCM2835_PLLH_PIX>,
- <&cprman BCM2835_CLOCK_HSM>;
- clock-names = "pixel", "hdmi";
diff --git a/target/linux/brcm2708/patches-4.4/0119-drm-vc4-Synchronize-validation-code-for-v2-submissio.patch b/target/linux/brcm2708/patches-4.4/0119-drm-vc4-Synchronize-validation-code-for-v2-submissio.patch
deleted file mode 100644
index eb43367..0000000
--- a/target/linux/brcm2708/patches-4.4/0119-drm-vc4-Synchronize-validation-code-for-v2-submissio.patch
+++ /dev/null
@@ -1,612 +0,0 @@
-From 129a21c953913f3373cb8c89928049b2da625400 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 7 Dec 2015 12:35:01 -0800
-Subject: [PATCH] drm/vc4: Synchronize validation code for v2 submission
- upstream.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_drv.h | 24 +--
- drivers/gpu/drm/vc4/vc4_gem.c | 14 +-
- drivers/gpu/drm/vc4/vc4_render_cl.c | 6 +-
- drivers/gpu/drm/vc4/vc4_validate.c | 287 +++++++++++++++---------------------
- 4 files changed, 135 insertions(+), 196 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_drv.h
-+++ b/drivers/gpu/drm/vc4/vc4_drv.h
-@@ -189,17 +189,6 @@ to_vc4_encoder(struct drm_encoder *encod
- #define HVS_READ(offset) readl(vc4->hvs->regs + offset)
- #define HVS_WRITE(offset, val) writel(val, vc4->hvs->regs + offset)
-
--enum vc4_bo_mode {
-- VC4_MODE_UNDECIDED,
-- VC4_MODE_RENDER,
-- VC4_MODE_SHADER,
--};
--
--struct vc4_bo_exec_state {
-- struct drm_gem_cma_object *bo;
-- enum vc4_bo_mode mode;
--};
--
- struct vc4_exec_info {
- /* Sequence number for this bin/render job. */
- uint64_t seqno;
-@@ -210,7 +199,7 @@ struct vc4_exec_info {
- /* This is the array of BOs that were looked up at the start of exec.
- * Command validation will use indices into this array.
- */
-- struct vc4_bo_exec_state *bo;
-+ struct drm_gem_cma_object **bo;
- uint32_t bo_count;
-
- /* Pointers for our position in vc4->job_list */
-@@ -238,7 +227,6 @@ struct vc4_exec_info {
- * command lists.
- */
- struct vc4_shader_state {
-- uint8_t packet;
- uint32_t addr;
- /* Maximum vertex index referenced by any primitive using this
- * shader state.
-@@ -254,6 +242,7 @@ struct vc4_exec_info {
- bool found_tile_binning_mode_config_packet;
- bool found_start_tile_binning_packet;
- bool found_increment_semaphore_packet;
-+ bool found_flush;
- uint8_t bin_tiles_x, bin_tiles_y;
- struct drm_gem_cma_object *tile_bo;
- uint32_t tile_alloc_offset;
-@@ -265,6 +254,9 @@ struct vc4_exec_info {
- uint32_t ct0ca, ct0ea;
- uint32_t ct1ca, ct1ea;
-
-+ /* Pointer to the unvalidated bin CL (if present). */
-+ void *bin_u;
-+
- /* Pointers to the shader recs. These paddr gets incremented as CL
- * packets are relocated in validate_gl_shader_state, and the vaddrs
- * (u and v) get incremented and size decremented as the shader recs
-@@ -455,10 +447,8 @@ vc4_validate_bin_cl(struct drm_device *d
- int
- vc4_validate_shader_recs(struct drm_device *dev, struct vc4_exec_info *exec);
-
--bool vc4_use_bo(struct vc4_exec_info *exec,
-- uint32_t hindex,
-- enum vc4_bo_mode mode,
-- struct drm_gem_cma_object **obj);
-+struct drm_gem_cma_object *vc4_use_bo(struct vc4_exec_info *exec,
-+ uint32_t hindex);
-
- int vc4_get_rcl(struct drm_device *dev, struct vc4_exec_info *exec);
-
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -169,8 +169,8 @@ vc4_save_hang_state(struct drm_device *d
- }
-
- for (i = 0; i < exec->bo_count; i++) {
-- drm_gem_object_reference(&exec->bo[i].bo->base);
-- kernel_state->bo[i] = &exec->bo[i].bo->base;
-+ drm_gem_object_reference(&exec->bo[i]->base);
-+ kernel_state->bo[i] = &exec->bo[i]->base;
- }
-
- list_for_each_entry(bo, &exec->unref_list, unref_head) {
-@@ -397,7 +397,7 @@ vc4_update_bo_seqnos(struct vc4_exec_inf
- unsigned i;
-
- for (i = 0; i < exec->bo_count; i++) {
-- bo = to_vc4_bo(&exec->bo[i].bo->base);
-+ bo = to_vc4_bo(&exec->bo[i]->base);
- bo->seqno = seqno;
- }
-
-@@ -467,7 +467,7 @@ vc4_cl_lookup_bos(struct drm_device *dev
- return -EINVAL;
- }
-
-- exec->bo = kcalloc(exec->bo_count, sizeof(struct vc4_bo_exec_state),
-+ exec->bo = kcalloc(exec->bo_count, sizeof(struct drm_gem_cma_object *),
- GFP_KERNEL);
- if (!exec->bo) {
- DRM_ERROR("Failed to allocate validated BO pointers\n");
-@@ -500,7 +500,7 @@ vc4_cl_lookup_bos(struct drm_device *dev
- goto fail;
- }
- drm_gem_object_reference(bo);
-- exec->bo[i].bo = (struct drm_gem_cma_object *)bo;
-+ exec->bo[i] = (struct drm_gem_cma_object *)bo;
- }
- spin_unlock(&file_priv->table_lock);
-
-@@ -591,6 +591,8 @@ vc4_get_bcl(struct drm_device *dev, stru
-
- exec->ct0ca = exec->exec_bo->paddr + bin_offset;
-
-+ exec->bin_u = bin;
-+
- exec->shader_rec_v = exec->exec_bo->vaddr + shader_rec_offset;
- exec->shader_rec_p = exec->exec_bo->paddr + shader_rec_offset;
- exec->shader_rec_size = args->shader_rec_size;
-@@ -622,7 +624,7 @@ vc4_complete_exec(struct drm_device *dev
- mutex_lock(&dev->struct_mutex);
- if (exec->bo) {
- for (i = 0; i < exec->bo_count; i++)
-- drm_gem_object_unreference(&exec->bo[i].bo->base);
-+ drm_gem_object_unreference(&exec->bo[i]->base);
- kfree(exec->bo);
- }
-
---- a/drivers/gpu/drm/vc4/vc4_render_cl.c
-+++ b/drivers/gpu/drm/vc4/vc4_render_cl.c
-@@ -436,7 +436,8 @@ static int vc4_rcl_surface_setup(struct
- if (surf->hindex == ~0)
- return 0;
-
-- if (!vc4_use_bo(exec, surf->hindex, VC4_MODE_RENDER, obj))
-+ *obj = vc4_use_bo(exec, surf->hindex);
-+ if (!*obj)
- return -EINVAL;
-
- if (surf->flags & VC4_SUBMIT_RCL_SURFACE_READ_IS_FULL_RES) {
-@@ -537,7 +538,8 @@ vc4_rcl_render_config_surface_setup(stru
- if (surf->hindex == ~0)
- return 0;
-
-- if (!vc4_use_bo(exec, surf->hindex, VC4_MODE_RENDER, obj))
-+ *obj = vc4_use_bo(exec, surf->hindex);
-+ if (!*obj)
- return -EINVAL;
-
- if (tiling > VC4_TILING_FORMAT_LT) {
---- a/drivers/gpu/drm/vc4/vc4_validate.c
-+++ b/drivers/gpu/drm/vc4/vc4_validate.c
-@@ -94,42 +94,42 @@ size_is_lt(uint32_t width, uint32_t heig
- height <= 4 * utile_height(cpp));
- }
-
--bool
--vc4_use_bo(struct vc4_exec_info *exec,
-- uint32_t hindex,
-- enum vc4_bo_mode mode,
-- struct drm_gem_cma_object **obj)
-+struct drm_gem_cma_object *
-+vc4_use_bo(struct vc4_exec_info *exec, uint32_t hindex)
- {
-- *obj = NULL;
-+ struct drm_gem_cma_object *obj;
-+ struct vc4_bo *bo;
-
- if (hindex >= exec->bo_count) {
- DRM_ERROR("BO index %d greater than BO count %d\n",
- hindex, exec->bo_count);
-- return false;
-+ return NULL;
- }
-+ obj = exec->bo[hindex];
-+ bo = to_vc4_bo(&obj->base);
-
-- if (exec->bo[hindex].mode != mode) {
-- if (exec->bo[hindex].mode == VC4_MODE_UNDECIDED) {
-- exec->bo[hindex].mode = mode;
-- } else {
-- DRM_ERROR("BO index %d reused with mode %d vs %d\n",
-- hindex, exec->bo[hindex].mode, mode);
-- return false;
-- }
-+ if (bo->validated_shader) {
-+ DRM_ERROR("Trying to use shader BO as something other than "
-+ "a shader\n");
-+ return NULL;
- }
-
-- *obj = exec->bo[hindex].bo;
-- return true;
-+ return obj;
-+}
-+
-+static struct drm_gem_cma_object *
-+vc4_use_handle(struct vc4_exec_info *exec, uint32_t gem_handles_packet_index)
-+{
-+ return vc4_use_bo(exec, exec->bo_index[gem_handles_packet_index]);
- }
-
- static bool
--vc4_use_handle(struct vc4_exec_info *exec,
-- uint32_t gem_handles_packet_index,
-- enum vc4_bo_mode mode,
-- struct drm_gem_cma_object **obj)
-+validate_bin_pos(struct vc4_exec_info *exec, void *untrusted, uint32_t pos)
- {
-- return vc4_use_bo(exec, exec->bo_index[gem_handles_packet_index],
-- mode, obj);
-+ /* Note that the untrusted pointer passed to these functions is
-+ * incremented past the packet byte.
-+ */
-+ return (untrusted - 1 == exec->bin_u + pos);
- }
-
- static uint32_t
-@@ -202,13 +202,13 @@ vc4_check_tex_size(struct vc4_exec_info
- }
-
- static int
--validate_flush_all(VALIDATE_ARGS)
-+validate_flush(VALIDATE_ARGS)
- {
-- if (exec->found_increment_semaphore_packet) {
-- DRM_ERROR("VC4_PACKET_FLUSH_ALL after "
-- "VC4_PACKET_INCREMENT_SEMAPHORE\n");
-+ if (!validate_bin_pos(exec, untrusted, exec->args->bin_cl_size - 1)) {
-+ DRM_ERROR("Bin CL must end with VC4_PACKET_FLUSH\n");
- return -EINVAL;
- }
-+ exec->found_flush = true;
-
- return 0;
- }
-@@ -233,17 +233,13 @@ validate_start_tile_binning(VALIDATE_ARG
- static int
- validate_increment_semaphore(VALIDATE_ARGS)
- {
-- if (exec->found_increment_semaphore_packet) {
-- DRM_ERROR("Duplicate VC4_PACKET_INCREMENT_SEMAPHORE\n");
-+ if (!validate_bin_pos(exec, untrusted, exec->args->bin_cl_size - 2)) {
-+ DRM_ERROR("Bin CL must end with "
-+ "VC4_PACKET_INCREMENT_SEMAPHORE\n");
- return -EINVAL;
- }
- exec->found_increment_semaphore_packet = true;
-
-- /* Once we've found the semaphore increment, there should be one FLUSH
-- * then the end of the command list. The FLUSH actually triggers the
-- * increment, so we only need to make sure there
-- */
--
- return 0;
- }
-
-@@ -257,11 +253,6 @@ validate_indexed_prim_list(VALIDATE_ARGS
- uint32_t index_size = (*(uint8_t *)(untrusted + 0) >> 4) ? 2 : 1;
- struct vc4_shader_state *shader_state;
-
-- if (exec->found_increment_semaphore_packet) {
-- DRM_ERROR("Drawing after VC4_PACKET_INCREMENT_SEMAPHORE\n");
-- return -EINVAL;
-- }
--
- /* Check overflow condition */
- if (exec->shader_state_count == 0) {
- DRM_ERROR("shader state must precede primitives\n");
-@@ -272,7 +263,8 @@ validate_indexed_prim_list(VALIDATE_ARGS
- if (max_index > shader_state->max_index)
- shader_state->max_index = max_index;
-
-- if (!vc4_use_handle(exec, 0, VC4_MODE_RENDER, &ib))
-+ ib = vc4_use_handle(exec, 0);
-+ if (!ib)
- return -EINVAL;
-
- if (offset > ib->base.size ||
-@@ -295,11 +287,6 @@ validate_gl_array_primitive(VALIDATE_ARG
- uint32_t max_index;
- struct vc4_shader_state *shader_state;
-
-- if (exec->found_increment_semaphore_packet) {
-- DRM_ERROR("Drawing after VC4_PACKET_INCREMENT_SEMAPHORE\n");
-- return -EINVAL;
-- }
--
- /* Check overflow condition */
- if (exec->shader_state_count == 0) {
- DRM_ERROR("shader state must precede primitives\n");
-@@ -329,7 +316,6 @@ validate_gl_shader_state(VALIDATE_ARGS)
- return -EINVAL;
- }
-
-- exec->shader_state[i].packet = VC4_PACKET_GL_SHADER_STATE;
- exec->shader_state[i].addr = *(uint32_t *)untrusted;
- exec->shader_state[i].max_index = 0;
-
-@@ -348,31 +334,6 @@ validate_gl_shader_state(VALIDATE_ARGS)
- }
-
- static int
--validate_nv_shader_state(VALIDATE_ARGS)
--{
-- uint32_t i = exec->shader_state_count++;
--
-- if (i >= exec->shader_state_size) {
-- DRM_ERROR("More requests for shader states than declared\n");
-- return -EINVAL;
-- }
--
-- exec->shader_state[i].packet = VC4_PACKET_NV_SHADER_STATE;
-- exec->shader_state[i].addr = *(uint32_t *)untrusted;
--
-- if (exec->shader_state[i].addr & 15) {
-- DRM_ERROR("NV shader state address 0x%08x misaligned\n",
-- exec->shader_state[i].addr);
-- return -EINVAL;
-- }
--
-- *(uint32_t *)validated = (exec->shader_state[i].addr +
-- exec->shader_rec_p);
--
-- return 0;
--}
--
--static int
- validate_tile_binning_config(VALIDATE_ARGS)
- {
- struct drm_device *dev = exec->exec_bo->base.dev;
-@@ -473,8 +434,8 @@ static const struct cmd_info {
- } cmd_info[] = {
- VC4_DEFINE_PACKET(VC4_PACKET_HALT, NULL),
- VC4_DEFINE_PACKET(VC4_PACKET_NOP, NULL),
-- VC4_DEFINE_PACKET(VC4_PACKET_FLUSH, NULL),
-- VC4_DEFINE_PACKET(VC4_PACKET_FLUSH_ALL, validate_flush_all),
-+ VC4_DEFINE_PACKET(VC4_PACKET_FLUSH, validate_flush),
-+ VC4_DEFINE_PACKET(VC4_PACKET_FLUSH_ALL, NULL),
- VC4_DEFINE_PACKET(VC4_PACKET_START_TILE_BINNING,
- validate_start_tile_binning),
- VC4_DEFINE_PACKET(VC4_PACKET_INCREMENT_SEMAPHORE,
-@@ -488,7 +449,6 @@ static const struct cmd_info {
- VC4_DEFINE_PACKET(VC4_PACKET_PRIMITIVE_LIST_FORMAT, NULL),
-
- VC4_DEFINE_PACKET(VC4_PACKET_GL_SHADER_STATE, validate_gl_shader_state),
-- VC4_DEFINE_PACKET(VC4_PACKET_NV_SHADER_STATE, validate_nv_shader_state),
-
- VC4_DEFINE_PACKET(VC4_PACKET_CONFIGURATION_BITS, NULL),
- VC4_DEFINE_PACKET(VC4_PACKET_FLAT_SHADE_FLAGS, NULL),
-@@ -575,8 +535,16 @@ vc4_validate_bin_cl(struct drm_device *d
- return -EINVAL;
- }
-
-- if (!exec->found_increment_semaphore_packet) {
-- DRM_ERROR("Bin CL missing VC4_PACKET_INCREMENT_SEMAPHORE\n");
-+ /* The bin CL must be ended with INCREMENT_SEMAPHORE and FLUSH. The
-+ * semaphore is used to trigger the render CL to start up, and the
-+ * FLUSH is what caps the bin lists with
-+ * VC4_PACKET_RETURN_FROM_SUB_LIST (so they jump back to the main
-+ * render CL when they get called to) and actually triggers the queued
-+ * semaphore increment.
-+ */
-+ if (!exec->found_increment_semaphore_packet || !exec->found_flush) {
-+ DRM_ERROR("Bin CL missing VC4_PACKET_INCREMENT_SEMAPHORE + "
-+ "VC4_PACKET_FLUSH\n");
- return -EINVAL;
- }
-
-@@ -607,7 +575,8 @@ reloc_tex(struct vc4_exec_info *exec,
- uint32_t cube_map_stride = 0;
- enum vc4_texture_data_type type;
-
-- if (!vc4_use_bo(exec, texture_handle_index, VC4_MODE_RENDER, &tex))
-+ tex = vc4_use_bo(exec, texture_handle_index);
-+ if (!tex)
- return false;
-
- if (sample->is_direct) {
-@@ -755,51 +724,28 @@ reloc_tex(struct vc4_exec_info *exec,
- }
-
- static int
--validate_shader_rec(struct drm_device *dev,
-- struct vc4_exec_info *exec,
-- struct vc4_shader_state *state)
-+validate_gl_shader_rec(struct drm_device *dev,
-+ struct vc4_exec_info *exec,
-+ struct vc4_shader_state *state)
- {
- uint32_t *src_handles;
- void *pkt_u, *pkt_v;
-- enum shader_rec_reloc_type {
-- RELOC_CODE,
-- RELOC_VBO,
-- };
-- struct shader_rec_reloc {
-- enum shader_rec_reloc_type type;
-- uint32_t offset;
-- };
-- static const struct shader_rec_reloc gl_relocs[] = {
-- { RELOC_CODE, 4 }, /* fs */
-- { RELOC_CODE, 16 }, /* vs */
-- { RELOC_CODE, 28 }, /* cs */
-- };
-- static const struct shader_rec_reloc nv_relocs[] = {
-- { RELOC_CODE, 4 }, /* fs */
-- { RELOC_VBO, 12 }
-+ static const uint32_t shader_reloc_offsets[] = {
-+ 4, /* fs */
-+ 16, /* vs */
-+ 28, /* cs */
- };
-- const struct shader_rec_reloc *relocs;
-- struct drm_gem_cma_object *bo[ARRAY_SIZE(gl_relocs) + 8];
-- uint32_t nr_attributes = 0, nr_fixed_relocs, nr_relocs, packet_size;
-+ uint32_t shader_reloc_count = ARRAY_SIZE(shader_reloc_offsets);
-+ struct drm_gem_cma_object *bo[shader_reloc_count + 8];
-+ uint32_t nr_attributes, nr_relocs, packet_size;
- int i;
-- struct vc4_validated_shader_info *shader;
-
-- if (state->packet == VC4_PACKET_NV_SHADER_STATE) {
-- relocs = nv_relocs;
-- nr_fixed_relocs = ARRAY_SIZE(nv_relocs);
--
-- packet_size = 16;
-- } else {
-- relocs = gl_relocs;
-- nr_fixed_relocs = ARRAY_SIZE(gl_relocs);
--
-- nr_attributes = state->addr & 0x7;
-- if (nr_attributes == 0)
-- nr_attributes = 8;
-- packet_size = gl_shader_rec_size(state->addr);
-- }
-- nr_relocs = nr_fixed_relocs + nr_attributes;
-+ nr_attributes = state->addr & 0x7;
-+ if (nr_attributes == 0)
-+ nr_attributes = 8;
-+ packet_size = gl_shader_rec_size(state->addr);
-
-+ nr_relocs = ARRAY_SIZE(shader_reloc_offsets) + nr_attributes;
- if (nr_relocs * 4 > exec->shader_rec_size) {
- DRM_ERROR("overflowed shader recs reading %d handles "
- "from %d bytes left\n",
-@@ -829,21 +775,30 @@ validate_shader_rec(struct drm_device *d
- exec->shader_rec_v += roundup(packet_size, 16);
- exec->shader_rec_size -= packet_size;
-
-- for (i = 0; i < nr_relocs; i++) {
-- enum vc4_bo_mode mode;
-+ if (!(*(uint16_t *)pkt_u & VC4_SHADER_FLAG_FS_SINGLE_THREAD)) {
-+ DRM_ERROR("Multi-threaded fragment shaders not supported.\n");
-+ return -EINVAL;
-+ }
-
-- if (i < nr_fixed_relocs && relocs[i].type == RELOC_CODE)
-- mode = VC4_MODE_SHADER;
-- else
-- mode = VC4_MODE_RENDER;
-+ for (i = 0; i < shader_reloc_count; i++) {
-+ if (src_handles[i] > exec->bo_count) {
-+ DRM_ERROR("Shader handle %d too big\n", src_handles[i]);
-+ return -EINVAL;
-+ }
-
-- if (!vc4_use_bo(exec, src_handles[i], mode, &bo[i]))
-- return false;
-+ bo[i] = exec->bo[src_handles[i]];
-+ if (!bo[i])
-+ return -EINVAL;
-+ }
-+ for (i = shader_reloc_count; i < nr_relocs; i++) {
-+ bo[i] = vc4_use_bo(exec, src_handles[i]);
-+ if (!bo[i])
-+ return -EINVAL;
- }
-
-- for (i = 0; i < nr_fixed_relocs; i++) {
-- struct vc4_bo *vc4_bo;
-- uint32_t o = relocs[i].offset;
-+ for (i = 0; i < shader_reloc_count; i++) {
-+ struct vc4_validated_shader_info *validated_shader;
-+ uint32_t o = shader_reloc_offsets[i];
- uint32_t src_offset = *(uint32_t *)(pkt_u + o);
- uint32_t *texture_handles_u;
- void *uniform_data_u;
-@@ -851,57 +806,50 @@ validate_shader_rec(struct drm_device *d
-
- *(uint32_t *)(pkt_v + o) = bo[i]->paddr + src_offset;
-
-- switch (relocs[i].type) {
-- case RELOC_CODE:
-- if (src_offset != 0) {
-- DRM_ERROR("Shaders must be at offset 0 "
-- "of the BO.\n");
-- goto fail;
-- }
-+ if (src_offset != 0) {
-+ DRM_ERROR("Shaders must be at offset 0 of "
-+ "the BO.\n");
-+ return -EINVAL;
-+ }
-
-- vc4_bo = to_vc4_bo(&bo[i]->base);
-- shader = vc4_bo->validated_shader;
-- if (!shader)
-- goto fail;
-+ validated_shader = to_vc4_bo(&bo[i]->base)->validated_shader;
-+ if (!validated_shader)
-+ return -EINVAL;
-
-- if (shader->uniforms_src_size > exec->uniforms_size) {
-- DRM_ERROR("Uniforms src buffer overflow\n");
-- goto fail;
-- }
-+ if (validated_shader->uniforms_src_size >
-+ exec->uniforms_size) {
-+ DRM_ERROR("Uniforms src buffer overflow\n");
-+ return -EINVAL;
-+ }
-
-- texture_handles_u = exec->uniforms_u;
-- uniform_data_u = (texture_handles_u +
-- shader->num_texture_samples);
--
-- memcpy(exec->uniforms_v, uniform_data_u,
-- shader->uniforms_size);
--
-- for (tex = 0;
-- tex < shader->num_texture_samples;
-- tex++) {
-- if (!reloc_tex(exec,
-- uniform_data_u,
-- &shader->texture_samples[tex],
-- texture_handles_u[tex])) {
-- goto fail;
-- }
-+ texture_handles_u = exec->uniforms_u;
-+ uniform_data_u = (texture_handles_u +
-+ validated_shader->num_texture_samples);
-+
-+ memcpy(exec->uniforms_v, uniform_data_u,
-+ validated_shader->uniforms_size);
-+
-+ for (tex = 0;
-+ tex < validated_shader->num_texture_samples;
-+ tex++) {
-+ if (!reloc_tex(exec,
-+ uniform_data_u,
-+ &validated_shader->texture_samples[tex],
-+ texture_handles_u[tex])) {
-+ return -EINVAL;
- }
-+ }
-
-- *(uint32_t *)(pkt_v + o + 4) = exec->uniforms_p;
--
-- exec->uniforms_u += shader->uniforms_src_size;
-- exec->uniforms_v += shader->uniforms_size;
-- exec->uniforms_p += shader->uniforms_size;
--
-- break;
-+ *(uint32_t *)(pkt_v + o + 4) = exec->uniforms_p;
-
-- case RELOC_VBO:
-- break;
-- }
-+ exec->uniforms_u += validated_shader->uniforms_src_size;
-+ exec->uniforms_v += validated_shader->uniforms_size;
-+ exec->uniforms_p += validated_shader->uniforms_size;
- }
-
- for (i = 0; i < nr_attributes; i++) {
-- struct drm_gem_cma_object *vbo = bo[nr_fixed_relocs + i];
-+ struct drm_gem_cma_object *vbo =
-+ bo[ARRAY_SIZE(shader_reloc_offsets) + i];
- uint32_t o = 36 + i * 8;
- uint32_t offset = *(uint32_t *)(pkt_u + o + 0);
- uint32_t attr_size = *(uint8_t *)(pkt_u + o + 4) + 1;
-@@ -933,9 +881,6 @@ validate_shader_rec(struct drm_device *d
- }
-
- return 0;
--
--fail:
-- return -EINVAL;
- }
-
- int
-@@ -946,7 +891,7 @@ vc4_validate_shader_recs(struct drm_devi
- int ret = 0;
-
- for (i = 0; i < exec->shader_state_count; i++) {
-- ret = validate_shader_rec(dev, exec, &exec->shader_state[i]);
-+ ret = validate_gl_shader_rec(dev, exec, &exec->shader_state[i]);
- if (ret)
- return ret;
- }
diff --git a/target/linux/brcm2708/patches-4.4/0120-MMC-Do-not-use-mmc_debug-if-CONFIG_MMC_BCM2835-is-no.patch b/target/linux/brcm2708/patches-4.4/0120-MMC-Do-not-use-mmc_debug-if-CONFIG_MMC_BCM2835-is-no.patch
deleted file mode 100644
index 37f2a56..0000000
--- a/target/linux/brcm2708/patches-4.4/0120-MMC-Do-not-use-mmc_debug-if-CONFIG_MMC_BCM2835-is-no.patch
+++ /dev/null
@@ -1,36 +0,0 @@
-From 8f8381d1d47cc2a82dee3d308bd71c654affa085 Mon Sep 17 00:00:00 2001
-From: janluca <janluca at zedat.fu-berlin.de>
-Date: Sun, 27 Dec 2015 14:34:04 +0100
-Subject: [PATCH] MMC: Do not use mmc_debug if CONFIG_MMC_BCM2835 is not set
-
-If CONFIG_MMC_BCM2835 was not set the compiling of the kernel failed
-since mmc_debug was not defined but used in drivers/mmc/core/quirks.c.
-
-This patch add a ifdef-check for CONFIG_MMC_BCM2835 to the change of
-commit 64d395457f793250d2e582eeb38cc3403b1db98c
----
- drivers/mmc/core/quirks.c | 4 ++++
- 1 file changed, 4 insertions(+)
-
---- a/drivers/mmc/core/quirks.c
-+++ b/drivers/mmc/core/quirks.c
-@@ -53,7 +53,9 @@ static const struct mmc_fixup mmc_fixup_
-
- void mmc_fixup_device(struct mmc_card *card, const struct mmc_fixup *table)
- {
-+#ifdef CONFIG_MMC_BCM2835
- extern unsigned mmc_debug;
-+#endif
- const struct mmc_fixup *f;
- u64 rev = cid_rev_card(card);
-
-@@ -81,7 +83,9 @@ void mmc_fixup_device(struct mmc_card *c
- /* SDHCI on BCM2708 - bug causes a certain sequence of CMD23 operations to fail.
- * Disable this flag for all cards (fall-back to CMD25/CMD18 multi-block transfers).
- */
-+#ifdef CONFIG_MMC_BCM2835
- if (mmc_debug & (1<<13))
- card->quirks |= MMC_QUIRK_BLK_NO_CMD23;
-+#endif
- }
- EXPORT_SYMBOL(mmc_fixup_device);
diff --git a/target/linux/brcm2708/patches-4.4/0121-Extend-clock-timeout-fix-modprobe-baudrate-parameter.patch b/target/linux/brcm2708/patches-4.4/0121-Extend-clock-timeout-fix-modprobe-baudrate-parameter.patch
deleted file mode 100644
index 20c54d5..0000000
--- a/target/linux/brcm2708/patches-4.4/0121-Extend-clock-timeout-fix-modprobe-baudrate-parameter.patch
+++ /dev/null
@@ -1,107 +0,0 @@
-From 3239987e97227ed6dcad81498b98f6e40c2a81a8 Mon Sep 17 00:00:00 2001
-From: Devon Fyson <devonfyson at gmail.com>
-Date: Wed, 30 Dec 2015 16:40:47 -0500
-Subject: [PATCH] Extend clock timeout, fix modprobe baudrate parameter.
-
-Set the BSC_CLKT clock streching timeout to 35ms as per SMBus specs.\n- Increase priority of baudrate parameter passed to modprobe (in /etc/modprobe.d/*.conf or command line). Currently custom baudrates don't work because they are overridden by clock-frequency in the platform_device passed to the function.
----
- drivers/i2c/busses/i2c-bcm2708.c | 45 ++++++++++++++++++++++++++--------------
- 1 file changed, 29 insertions(+), 16 deletions(-)
-
---- a/drivers/i2c/busses/i2c-bcm2708.c
-+++ b/drivers/i2c/busses/i2c-bcm2708.c
-@@ -71,7 +71,8 @@
-
- #define DRV_NAME "bcm2708_i2c"
-
--static unsigned int baudrate = CONFIG_I2C_BCM2708_BAUDRATE;
-+static unsigned int baudrate_default = CONFIG_I2C_BCM2708_BAUDRATE;
-+static unsigned int baudrate;
- module_param(baudrate, uint, S_IRUSR | S_IWUSR | S_IRGRP | S_IWGRP);
- MODULE_PARM_DESC(baudrate, "The I2C baudrate");
-
-@@ -87,6 +88,7 @@ struct bcm2708_i2c {
- int irq;
- struct clk *clk;
- u32 cdiv;
-+ u32 clk_tout;
-
- struct completion done;
-
-@@ -126,7 +128,7 @@ static inline void bcm2708_bsc_fifo_fill
-
- static inline int bcm2708_bsc_setup(struct bcm2708_i2c *bi)
- {
-- u32 cdiv, s;
-+ u32 cdiv, s, clk_tout;
- u32 c = BSC_C_I2CEN | BSC_C_INTD | BSC_C_ST | BSC_C_CLEAR_1;
- int wait_loops = I2C_WAIT_LOOP_COUNT;
-
-@@ -134,12 +136,14 @@ static inline int bcm2708_bsc_setup(stru
- * Use the value that we cached in the probe.
- */
- cdiv = bi->cdiv;
-+ clk_tout = bi->clk_tout;
-
- if (bi->msg->flags & I2C_M_RD)
- c |= BSC_C_INTR | BSC_C_READ;
- else
- c |= BSC_C_INTT;
-
-+ bcm2708_wr(bi, BSC_CLKT, clk_tout);
- bcm2708_wr(bi, BSC_DIV, cdiv);
- bcm2708_wr(bi, BSC_A, bi->msg->addr);
- bcm2708_wr(bi, BSC_DLEN, bi->msg->len);
-@@ -312,21 +316,24 @@ static int bcm2708_i2c_probe(struct plat
- struct bcm2708_i2c *bi;
- struct i2c_adapter *adap;
- unsigned long bus_hz;
-- u32 cdiv;
--
-- if (pdev->dev.of_node) {
-- u32 bus_clk_rate;
-- pdev->id = of_alias_get_id(pdev->dev.of_node, "i2c");
-- if (pdev->id < 0) {
-- dev_err(&pdev->dev, "alias is missing\n");
-- return -EINVAL;
-+ u32 cdiv, clk_tout;
-+
-+ if (!baudrate) {
-+ baudrate = baudrate_default;
-+ if (pdev->dev.of_node) {
-+ u32 bus_clk_rate;
-+ pdev->id = of_alias_get_id(pdev->dev.of_node, "i2c");
-+ if (pdev->id < 0) {
-+ dev_err(&pdev->dev, "alias is missing\n");
-+ return -EINVAL;
-+ }
-+ if (!of_property_read_u32(pdev->dev.of_node,
-+ "clock-frequency", &bus_clk_rate))
-+ baudrate = bus_clk_rate;
-+ else
-+ dev_warn(&pdev->dev,
-+ "Could not read clock-frequency property\n");
- }
-- if (!of_property_read_u32(pdev->dev.of_node,
-- "clock-frequency", &bus_clk_rate))
-- baudrate = bus_clk_rate;
-- else
-- dev_warn(&pdev->dev,
-- "Could not read clock-frequency property\n");
- }
-
- regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-@@ -417,7 +424,13 @@ static int bcm2708_i2c_probe(struct plat
- cdiv = 0xffff;
- baudrate = bus_hz / cdiv;
- }
-+
-+ clk_tout = 35/1000*baudrate; //35ms timeout as per SMBus specs.
-+ if (clk_tout > 0xffff)
-+ clk_tout = 0xffff;
-+
- bi->cdiv = cdiv;
-+ bi->clk_tout = clk_tout;
-
- dev_info(&pdev->dev, "BSC%d Controller at 0x%08lx (irq %d) (baudrate %d)\n",
- pdev->id, (unsigned long)regs->start, irq, baudrate);
diff --git a/target/linux/brcm2708/patches-4.4/0122-bcm270x_dt-Add-dwc2-and-dwc-otg-overlays.patch b/target/linux/brcm2708/patches-4.4/0122-bcm270x_dt-Add-dwc2-and-dwc-otg-overlays.patch
deleted file mode 100644
index 2924275..0000000
--- a/target/linux/brcm2708/patches-4.4/0122-bcm270x_dt-Add-dwc2-and-dwc-otg-overlays.patch
+++ /dev/null
@@ -1,110 +0,0 @@
-From eb92559814cd3054166d9e53765d7c193f0b2f41 Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Noralf=20Tr=C3=B8nnes?= <noralf at tronnes.org>
-Date: Thu, 31 Dec 2015 16:44:58 +0100
-Subject: [PATCH] bcm270x_dt: Add dwc2 and dwc-otg overlays
-
----
- arch/arm/boot/dts/overlays/Makefile | 2 ++
- arch/arm/boot/dts/overlays/README | 21 +++++++++++++++++++
- arch/arm/boot/dts/overlays/dwc-otg-overlay.dts | 20 ++++++++++++++++++
- arch/arm/boot/dts/overlays/dwc2-overlay.dts | 29 ++++++++++++++++++++++++++
- 4 files changed, 72 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/dwc-otg-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/dwc2-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -15,6 +15,8 @@ endif
- dtb-$(RPI_DT_OVERLAYS) += ads7846-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += at86rf233-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += bmp085_i2c-sensor-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += dwc2-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += dwc-otg-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += dht11-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += enc28j60-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += gpio-ir-overlay.dtb
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -198,6 +198,27 @@ Params: gpiopin GPIO co
- (default 4)
-
-
-+Name: dwc-otg
-+Info: Selects the dwc_otg USB controller driver which has fiq support. This
-+ is the default on all except the Pi Zero which defaults to dwc2.
-+Load: dtoverlay=dwc-otg
-+Params: <None>
-+
-+
-+Name: dwc2
-+Info: Selects the dwc2 USB controller driver
-+Load: dtoverlay=dwc2,<param>=<val>
-+Params: dr_mode Dual role mode: "host", "peripheral" or "otg"
-+
-+ g-rx-fifo-size Size of rx fifo size in gadget mode
-+
-+ g-np-tx-fifo-size Size of non-periodic tx fifo size in gadget
-+ mode
-+
-+ g-tx-fifo-size Size of periodic tx fifo per endpoint
-+ (except ep0) in gadget mode
-+
-+
- [ The ds1307-rtc overlay has been deleted. See i2c-rtc. ]
-
-
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/dwc-otg-overlay.dts
-@@ -0,0 +1,20 @@
-+/dts-v1/;
-+/plugin/;
-+
-+/{
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&usb>;
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+ __overlay__ {
-+ compatible = "brcm,bcm2708-usb";
-+ reg = <0x7e980000 0x10000>,
-+ <0x7e006000 0x1000>;
-+ interrupts = <2 0>,
-+ <1 9>;
-+ status = "okay";
-+ };
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/dwc2-overlay.dts
-@@ -0,0 +1,29 @@
-+/dts-v1/;
-+/plugin/;
-+
-+/{
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&usb>;
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+ __overlay__ {
-+ compatible = "brcm,bcm2835-usb";
-+ reg = <0x7e980000 0x10000>;
-+ interrupts = <1 9>;
-+ dr_mode = "otg";
-+ g-np-tx-fifo-size = <32>;
-+ g-rx-fifo-size = <256>;
-+ g-tx-fifo-size = <256 128 128 64 64 64 32>;
-+ status = "okay";
-+ };
-+ };
-+
-+ __overrides__ {
-+ dr_mode = <&usb>, "dr_mode";
-+ g-np-tx-fifo-size = <&usb>,"g-np-tx-fifo-size:0";
-+ g-rx-fifo-size = <&usb>,"g-rx-fifo-size:0";
-+ g-tx-fifo-size = <&usb>,"g-tx-fifo-size:0";
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0123-BCM270X_DT-Add-the-sdtweak-overlay-for-tuning-sdhost.patch b/target/linux/brcm2708/patches-4.4/0123-BCM270X_DT-Add-the-sdtweak-overlay-for-tuning-sdhost.patch
deleted file mode 100644
index e2ad522..0000000
--- a/target/linux/brcm2708/patches-4.4/0123-BCM270X_DT-Add-the-sdtweak-overlay-for-tuning-sdhost.patch
+++ /dev/null
@@ -1,73 +0,0 @@
-From 29754f6751d0cdd5a9e1da94b30e5d0686557be9 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 4 Jan 2016 14:42:17 +0000
-Subject: [PATCH] BCM270X_DT: Add the sdtweak overlay, for tuning sdhost
-
-The sdhost overlay declares the sdhost interface and allows parameters
-to be set. This is overkill for situations where the user just wants to
-tweak the parameters of a pre-declared sdhost interface, so create an
-sdtweak overlay that does just that.
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 14 ++++++++++++++
- arch/arm/boot/dts/overlays/sdtweak-overlay.dts | 21 +++++++++++++++++++++
- 3 files changed, 36 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/sdtweak-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -53,6 +53,7 @@ dtb-$(RPI_DT_OVERLAYS) += rpi-proto-over
- dtb-$(RPI_DT_OVERLAYS) += rpi-sense-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += sdhost-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += sdio-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += sdtweak-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += smi-dev-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += smi-nand-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += smi-overlay.dtb
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -635,6 +635,20 @@ Params: overclock_50 Clock (
- (default on: polling once at boot-time)
-
-
-+Name: sdtweak
-+Info: Tunes the bcm2835-sdhost SD/MMC driver
-+Load: dtoverlay=sdtweak,<param>=<val>
-+Params: overclock_50 Clock (in MHz) to use when the MMC framework
-+ requests 50MHz
-+
-+ force_pio Disable DMA support (default off)
-+
-+ pio_limit Number of blocks above which to use DMA
-+ (default 1)
-+
-+ debug Enable debug output (default off)
-+
-+
- Name: smi
- Info: Enables the Secondary Memory Interface peripheral. Uses GPIOs 2-25!
- Load: dtoverlay=smi
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/sdtweak-overlay.dts
-@@ -0,0 +1,21 @@
-+/dts-v1/;
-+/plugin/;
-+
-+/{
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&sdhost>;
-+ frag1: __overlay__ {
-+ brcm,overclock-50 = <0>;
-+ brcm,pio-limit = <1>;
-+ };
-+ };
-+
-+ __overrides__ {
-+ overclock_50 = <&frag1>,"brcm,overclock-50:0";
-+ force_pio = <&frag1>,"brcm,force-pio?";
-+ pio_limit = <&frag1>,"brcm,pio-limit:0";
-+ debug = <&frag1>,"brcm,debug?";
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0124-bcm2835-mmc-Don-t-override-bus-width-capabilities-fr.patch b/target/linux/brcm2708/patches-4.4/0124-bcm2835-mmc-Don-t-override-bus-width-capabilities-fr.patch
deleted file mode 100644
index 06d5cf7..0000000
--- a/target/linux/brcm2708/patches-4.4/0124-bcm2835-mmc-Don-t-override-bus-width-capabilities-fr.patch
+++ /dev/null
@@ -1,24 +0,0 @@
-From 78d792a868d92d6d4703fa1e60c5dd0d84bdf6ff Mon Sep 17 00:00:00 2001
-From: Andrew Litt <ajlitt at splunge.net>
-Date: Mon, 11 Jan 2016 07:54:21 +0000
-Subject: [PATCH] bcm2835-mmc: Don't override bus width capabilities from
- devicetree
-
-Take out the force setting of the MMC_CAP_4_BIT_DATA host capability
-so that the result read from devicetree via mmc_of_parse() is
-preserved.
----
- drivers/mmc/host/bcm2835-mmc.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/mmc/host/bcm2835-mmc.c
-+++ b/drivers/mmc/host/bcm2835-mmc.c
-@@ -1305,7 +1305,7 @@ static int bcm2835_mmc_add_host(struct b
- /* host controller capabilities */
- mmc->caps |= MMC_CAP_CMD23 | MMC_CAP_ERASE | MMC_CAP_NEEDS_POLL |
- MMC_CAP_SDIO_IRQ | MMC_CAP_SD_HIGHSPEED |
-- MMC_CAP_MMC_HIGHSPEED | MMC_CAP_4_BIT_DATA;
-+ MMC_CAP_MMC_HIGHSPEED;
-
- mmc->caps2 |= MMC_CAP2_SDIO_IRQ_NOTHREAD;
-
diff --git a/target/linux/brcm2708/patches-4.4/0125-SDIO-overlay-add-bus_width-parameter.patch b/target/linux/brcm2708/patches-4.4/0125-SDIO-overlay-add-bus_width-parameter.patch
deleted file mode 100644
index 78bed04..0000000
--- a/target/linux/brcm2708/patches-4.4/0125-SDIO-overlay-add-bus_width-parameter.patch
+++ /dev/null
@@ -1,42 +0,0 @@
-From 597258492a6930e916cb16c09b3adf1508062a00 Mon Sep 17 00:00:00 2001
-From: Andrew Litt <ajlitt at splunge.net>
-Date: Mon, 11 Jan 2016 07:55:54 +0000
-Subject: [PATCH] SDIO-overlay: add bus_width parameter
-
-Allow setting of the SDIO bus width capability of the bcm2835-mmc
-host. This is helpful when only a 1 bit wide bus is connected
-between host and device but both host and device advertise 4 bit
-mode.
----
- arch/arm/boot/dts/overlays/README | 2 ++
- arch/arm/boot/dts/overlays/sdio-overlay.dts | 2 ++
- 2 files changed, 4 insertions(+)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -634,6 +634,8 @@ Params: overclock_50 Clock (
- poll_once Disable SDIO-device polling every second
- (default on: polling once at boot-time)
-
-+ bus_width Set the SDIO host bus width (default 4 bits)
-+
-
- Name: sdtweak
- Info: Tunes the bcm2835-sdhost SD/MMC driver
---- a/arch/arm/boot/dts/overlays/sdio-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/sdio-overlay.dts
-@@ -11,6 +11,7 @@
- pinctrl-names = "default";
- pinctrl-0 = <&sdio_pins>;
- non-removable;
-+ bus-width = <4>;
- status = "okay";
- };
- };
-@@ -28,5 +29,6 @@
-
- __overrides__ {
- poll_once = <&sdio_mmc>,"non-removable?";
-+ bus_width = <&sdio_mmc>,"bus-width:0";
- };
- };
diff --git a/target/linux/brcm2708/patches-4.4/0126-bcm2835-extend-allowed-range-of-channels-and-sampler.patch b/target/linux/brcm2708/patches-4.4/0126-bcm2835-extend-allowed-range-of-channels-and-sampler.patch
deleted file mode 100644
index b622210..0000000
--- a/target/linux/brcm2708/patches-4.4/0126-bcm2835-extend-allowed-range-of-channels-and-sampler.patch
+++ /dev/null
@@ -1,36 +0,0 @@
-From 67389892940501bcb998a5ab55bb337beb406e39 Mon Sep 17 00:00:00 2001
-From: wm4 <wm4 at nowhere>
-Date: Wed, 13 Jan 2016 19:41:45 +0100
-Subject: [PATCH] bcm2835: extend allowed range of channels and samplerates
-
-Allow everything the videocore accepts.
----
- sound/arm/bcm2835-pcm.c | 8 ++++----
- 1 file changed, 4 insertions(+), 4 deletions(-)
-
---- a/sound/arm/bcm2835-pcm.c
-+++ b/sound/arm/bcm2835-pcm.c
-@@ -26,9 +26,9 @@ static struct snd_pcm_hardware snd_bcm28
- .formats = SNDRV_PCM_FMTBIT_U8 | SNDRV_PCM_FMTBIT_S16_LE,
- .rates = SNDRV_PCM_RATE_CONTINUOUS | SNDRV_PCM_RATE_8000_48000,
- .rate_min = 8000,
-- .rate_max = 48000,
-+ .rate_max = 192000,
- .channels_min = 1,
-- .channels_max = 2,
-+ .channels_max = 8,
- .buffer_bytes_max = 128 * 1024,
- .period_bytes_min = 1 * 1024,
- .period_bytes_max = 128 * 1024,
-@@ -43,9 +43,9 @@ static struct snd_pcm_hardware snd_bcm28
- .rates = SNDRV_PCM_RATE_CONTINUOUS | SNDRV_PCM_RATE_44100 |
- SNDRV_PCM_RATE_48000,
- .rate_min = 44100,
-- .rate_max = 48000,
-+ .rate_max = 192000,
- .channels_min = 2,
-- .channels_max = 2,
-+ .channels_max = 8,
- .buffer_bytes_max = 128 * 1024,
- .period_bytes_min = 1 * 1024,
- .period_bytes_max = 128 * 1024,
diff --git a/target/linux/brcm2708/patches-4.4/0127-bcm2835-restrict-channels-rate-to-8-960000.patch b/target/linux/brcm2708/patches-4.4/0127-bcm2835-restrict-channels-rate-to-8-960000.patch
deleted file mode 100644
index fc38b33..0000000
--- a/target/linux/brcm2708/patches-4.4/0127-bcm2835-restrict-channels-rate-to-8-960000.patch
+++ /dev/null
@@ -1,80 +0,0 @@
-From fe51d76ced4088c11981b835a7b741ee9e0df10e Mon Sep 17 00:00:00 2001
-From: wm4 <wm4 at nowhere>
-Date: Wed, 13 Jan 2016 19:42:18 +0100
-Subject: [PATCH] bcm2835: restrict channels*rate to 8*960000
-
-This is required at least for SPDIF. If the bitrate goes above,
-videocore will either resample the audio or corrupt it due to
-underruns. Supposedly the hardware isn't designed to output
-higher rates, but it can still resample it down to supported
-rates.
-
-Some code is based on ac97_pcm.c.
----
- sound/arm/bcm2835-pcm.c | 41 +++++++++++++++++++++++++++++++++++++++++
- 1 file changed, 41 insertions(+)
-
---- a/sound/arm/bcm2835-pcm.c
-+++ b/sound/arm/bcm2835-pcm.c
-@@ -19,6 +19,9 @@
-
- #include "bcm2835.h"
-
-+/* The hardware can not do much more num_channels*samplerate then this value */
-+#define MAX_COMBINED_RATE 768000
-+
- /* hardware definition */
- static struct snd_pcm_hardware snd_bcm2835_playback_hw = {
- .info = (SNDRV_PCM_INFO_INTERLEAVED | SNDRV_PCM_INFO_BLOCK_TRANSFER |
-@@ -107,6 +110,31 @@ static irqreturn_t bcm2835_playback_fifo
- return IRQ_HANDLED;
- }
-
-+
-+static int rate_hw_constraint_rate(struct snd_pcm_hw_params *params,
-+ struct snd_pcm_hw_rule *rule)
-+{
-+ struct snd_interval *channels = hw_param_interval(params, SNDRV_PCM_HW_PARAM_CHANNELS);
-+ struct snd_interval rates = {
-+ .min = 8000,
-+ .max = min(192000u, MAX_COMBINED_RATE / max(channels->min, 1u)),
-+ };
-+ struct snd_interval *rate = hw_param_interval(params, SNDRV_PCM_HW_PARAM_RATE);
-+ return snd_interval_refine(rate, &rates);
-+}
-+
-+static int rate_hw_constraint_channels(struct snd_pcm_hw_params *params,
-+ struct snd_pcm_hw_rule *rule)
-+{
-+ struct snd_interval *rate = hw_param_interval(params, SNDRV_PCM_HW_PARAM_RATE);
-+ struct snd_interval channels_interval = {
-+ .min = 1,
-+ .max = min(8u, MAX_COMBINED_RATE / max(rate->min, 1u)),
-+ };
-+ struct snd_interval *channels = hw_param_interval(params, SNDRV_PCM_HW_PARAM_CHANNELS);
-+ return snd_interval_refine(channels, &channels_interval);
-+}
-+
- /* open callback */
- static int snd_bcm2835_playback_open_generic(
- struct snd_pcm_substream *substream, int spdif)
-@@ -188,6 +216,19 @@ static int snd_bcm2835_playback_open_gen
- snd_pcm_hw_constraint_step(runtime, 0, SNDRV_PCM_HW_PARAM_PERIOD_BYTES,
- 16);
-
-+ /* When playing PCM, pretend that we support the full range of channels
-+ * and sample rates. The GPU can't output it, but is able to resample
-+ * the data to a rate the hardware can handle it. This won't work with
-+ * compressed data; the resampler would just destroy it. */
-+ if (spdif) {
-+ err = snd_pcm_hw_rule_add(runtime, 0, SNDRV_PCM_HW_PARAM_RATE,
-+ rate_hw_constraint_rate, NULL,
-+ SNDRV_PCM_HW_PARAM_CHANNELS, -1);
-+ err = snd_pcm_hw_rule_add(runtime, 0, SNDRV_PCM_HW_PARAM_CHANNELS,
-+ rate_hw_constraint_channels, NULL,
-+ SNDRV_PCM_HW_PARAM_RATE, -1);
-+ }
-+
- chip->alsa_stream[idx] = alsa_stream;
-
- chip->opened |= (1 << idx);
diff --git a/target/linux/brcm2708/patches-4.4/0128-rpi-update-vc_vchi_audioserv_defs.h.patch b/target/linux/brcm2708/patches-4.4/0128-rpi-update-vc_vchi_audioserv_defs.h.patch
deleted file mode 100644
index 10e3e21..0000000
--- a/target/linux/brcm2708/patches-4.4/0128-rpi-update-vc_vchi_audioserv_defs.h.patch
+++ /dev/null
@@ -1,66 +0,0 @@
-From 7fe7d97c537f09a1fb160a7ec61fd26d97ab06ee Mon Sep 17 00:00:00 2001
-From: wm4 <wm4 at nowhere>
-Date: Wed, 13 Jan 2016 19:42:48 +0100
-Subject: [PATCH] rpi: update vc_vchi_audioserv_defs.h
-
-Add audioserv 3 extensions. The changes were taken from the paste
-linked here:
-
-https://github.com/raspberrypi/linux/pull/1166#issuecomment-151917067
----
- sound/arm/vc_vchi_audioserv_defs.h | 13 +++++++++++--
- 1 file changed, 11 insertions(+), 2 deletions(-)
-
---- a/sound/arm/vc_vchi_audioserv_defs.h
-+++ b/sound/arm/vc_vchi_audioserv_defs.h
-@@ -16,7 +16,7 @@
- #define _VC_AUDIO_DEFS_H_
-
- #define VC_AUDIOSERV_MIN_VER 1
--#define VC_AUDIOSERV_VER 2
-+#define VC_AUDIOSERV_VER 3
-
- // FourCC code used for VCHI connection
- #define VC_AUDIO_SERVER_NAME MAKE_FOURCC("AUDS")
-@@ -36,6 +36,7 @@ typedef enum {
- VC_AUDIO_MSG_TYPE_START, // Configure audio
- VC_AUDIO_MSG_TYPE_STOP, // Configure audio
- VC_AUDIO_MSG_TYPE_WRITE, // Configure audio
-+ VC_AUDIO_MSG_TYPE_LATENCY, // request latency in cycles
- VC_AUDIO_MSG_TYPE_MAX
- } VC_AUDIO_MSG_TYPE;
-
-@@ -44,6 +45,7 @@ typedef struct {
- uint32_t channels;
- uint32_t samplerate;
- uint32_t bps;
-+ uint32_t channelmap;
-
- } VC_AUDIO_CONFIG_T;
-
-@@ -84,6 +86,12 @@ typedef struct {
- uint16_t max_packet;
- } VC_AUDIO_WRITE_T;
-
-+// query latency in samples of sink
-+typedef struct
-+{
-+ uint32_t dummy;
-+} VC_AUDIO_LATENCY_T;
-+
- // Generic result for a request (VC->HOST)
- typedef struct {
- int32_t success; // Success value
-@@ -108,9 +116,10 @@ typedef struct {
- VC_AUDIO_START_T start;
- VC_AUDIO_STOP_T stop;
- VC_AUDIO_WRITE_T write;
-+ VC_AUDIO_LATENCY_T latency;
- VC_AUDIO_RESULT_T result;
- VC_AUDIO_COMPLETE_T complete;
- } u;
- } VC_AUDIO_MSG_T;
-
--#endif // _VC_AUDIO_DEFS_H_
-+#endif // _VC_AUDIO_DEFS_H_
-\ No newline at end of file
diff --git a/target/linux/brcm2708/patches-4.4/0129-bcm2835-implement-channel-map-API.patch b/target/linux/brcm2708/patches-4.4/0129-bcm2835-implement-channel-map-API.patch
deleted file mode 100644
index 3da4fc4..0000000
--- a/target/linux/brcm2708/patches-4.4/0129-bcm2835-implement-channel-map-API.patch
+++ /dev/null
@@ -1,421 +0,0 @@
-From dead6a5d8c3cd19b1197b60a674f898270a8e1d1 Mon Sep 17 00:00:00 2001
-From: wm4 <wm4 at nowhere>
-Date: Wed, 13 Jan 2016 19:43:12 +0100
-Subject: [PATCH] bcm2835: implement channel map API
-
-Report all layouts supported by the HDMI protocol to userspace.
-Make the videocore set the correct layout according to the
-userspace request.
-
-Some code taken from patch_hdmi.c. In particular, the HDMI channel
-layout table was copied without changes - with the idea in mind that
-hopefully it can be shared one day. Or at least updating it will be
-simpler.
-
-In my tests, everything appears to work, except when outputting
-FL FR RL RR. Then my receiver outputs RL on both the RL and RR
-speakers, while RR is never heard.
----
- sound/arm/bcm2835-ctl.c | 276 ++++++++++++++++++++++++++++++++++++++++++++++
- sound/arm/bcm2835-pcm.c | 22 +++-
- sound/arm/bcm2835-vchiq.c | 13 +++
- sound/arm/bcm2835.h | 4 +
- 4 files changed, 311 insertions(+), 4 deletions(-)
-
---- a/sound/arm/bcm2835-ctl.c
-+++ b/sound/arm/bcm2835-ctl.c
-@@ -300,6 +300,281 @@ static struct snd_kcontrol_new snd_bcm28
- },
- };
-
-+struct cea_channel_speaker_allocation {
-+ int ca_index;
-+ int speakers[8];
-+};
-+
-+#define FL SNDRV_CHMAP_FL
-+#define FR SNDRV_CHMAP_FR
-+#define RL SNDRV_CHMAP_RL
-+#define RR SNDRV_CHMAP_RR
-+#define LFE SNDRV_CHMAP_LFE
-+#define FC SNDRV_CHMAP_FC
-+#define RLC SNDRV_CHMAP_RLC
-+#define RRC SNDRV_CHMAP_RRC
-+#define RC SNDRV_CHMAP_RC
-+#define FLC SNDRV_CHMAP_FLC
-+#define FRC SNDRV_CHMAP_FRC
-+#define FLH SNDRV_CHMAP_TFL
-+#define FRH SNDRV_CHMAP_TFR
-+#define FLW SNDRV_CHMAP_FLW
-+#define FRW SNDRV_CHMAP_FRW
-+#define TC SNDRV_CHMAP_TC
-+#define FCH SNDRV_CHMAP_TFC
-+
-+/*
-+ * CEA-861 channel maps
-+ *
-+ * Stolen from sound/pci/hda/patch_hdmi.c
-+ * (unlike the source, this uses SNDRV_* constants directly, as by the
-+ * map_tables array in patch_hdmi.c)
-+ * Unknown entries use 0, which unfortunately is SNDRV_CHMAP_UNKNOWN instead
-+ * of SNDRV_CHMAP_NA.
-+ */
-+static struct cea_channel_speaker_allocation channel_allocations[] = {
-+/* channel: 7 6 5 4 3 2 1 0 */
-+{ .ca_index = 0x00, .speakers = { 0, 0, 0, 0, 0, 0, FR, FL } },
-+ /* 2.1 */
-+{ .ca_index = 0x01, .speakers = { 0, 0, 0, 0, 0, LFE, FR, FL } },
-+ /* Dolby Surround */
-+{ .ca_index = 0x02, .speakers = { 0, 0, 0, 0, FC, 0, FR, FL } },
-+ /* surround40 */
-+{ .ca_index = 0x08, .speakers = { 0, 0, RR, RL, 0, 0, FR, FL } },
-+ /* surround41 */
-+{ .ca_index = 0x09, .speakers = { 0, 0, RR, RL, 0, LFE, FR, FL } },
-+ /* surround50 */
-+{ .ca_index = 0x0a, .speakers = { 0, 0, RR, RL, FC, 0, FR, FL } },
-+ /* surround51 */
-+{ .ca_index = 0x0b, .speakers = { 0, 0, RR, RL, FC, LFE, FR, FL } },
-+ /* 6.1 */
-+{ .ca_index = 0x0f, .speakers = { 0, RC, RR, RL, FC, LFE, FR, FL } },
-+ /* surround71 */
-+{ .ca_index = 0x13, .speakers = { RRC, RLC, RR, RL, FC, LFE, FR, FL } },
-+
-+{ .ca_index = 0x03, .speakers = { 0, 0, 0, 0, FC, LFE, FR, FL } },
-+{ .ca_index = 0x04, .speakers = { 0, 0, 0, RC, 0, 0, FR, FL } },
-+{ .ca_index = 0x05, .speakers = { 0, 0, 0, RC, 0, LFE, FR, FL } },
-+{ .ca_index = 0x06, .speakers = { 0, 0, 0, RC, FC, 0, FR, FL } },
-+{ .ca_index = 0x07, .speakers = { 0, 0, 0, RC, FC, LFE, FR, FL } },
-+{ .ca_index = 0x0c, .speakers = { 0, RC, RR, RL, 0, 0, FR, FL } },
-+{ .ca_index = 0x0d, .speakers = { 0, RC, RR, RL, 0, LFE, FR, FL } },
-+{ .ca_index = 0x0e, .speakers = { 0, RC, RR, RL, FC, 0, FR, FL } },
-+{ .ca_index = 0x10, .speakers = { RRC, RLC, RR, RL, 0, 0, FR, FL } },
-+{ .ca_index = 0x11, .speakers = { RRC, RLC, RR, RL, 0, LFE, FR, FL } },
-+{ .ca_index = 0x12, .speakers = { RRC, RLC, RR, RL, FC, 0, FR, FL } },
-+{ .ca_index = 0x14, .speakers = { FRC, FLC, 0, 0, 0, 0, FR, FL } },
-+{ .ca_index = 0x15, .speakers = { FRC, FLC, 0, 0, 0, LFE, FR, FL } },
-+{ .ca_index = 0x16, .speakers = { FRC, FLC, 0, 0, FC, 0, FR, FL } },
-+{ .ca_index = 0x17, .speakers = { FRC, FLC, 0, 0, FC, LFE, FR, FL } },
-+{ .ca_index = 0x18, .speakers = { FRC, FLC, 0, RC, 0, 0, FR, FL } },
-+{ .ca_index = 0x19, .speakers = { FRC, FLC, 0, RC, 0, LFE, FR, FL } },
-+{ .ca_index = 0x1a, .speakers = { FRC, FLC, 0, RC, FC, 0, FR, FL } },
-+{ .ca_index = 0x1b, .speakers = { FRC, FLC, 0, RC, FC, LFE, FR, FL } },
-+{ .ca_index = 0x1c, .speakers = { FRC, FLC, RR, RL, 0, 0, FR, FL } },
-+{ .ca_index = 0x1d, .speakers = { FRC, FLC, RR, RL, 0, LFE, FR, FL } },
-+{ .ca_index = 0x1e, .speakers = { FRC, FLC, RR, RL, FC, 0, FR, FL } },
-+{ .ca_index = 0x1f, .speakers = { FRC, FLC, RR, RL, FC, LFE, FR, FL } },
-+{ .ca_index = 0x20, .speakers = { 0, FCH, RR, RL, FC, 0, FR, FL } },
-+{ .ca_index = 0x21, .speakers = { 0, FCH, RR, RL, FC, LFE, FR, FL } },
-+{ .ca_index = 0x22, .speakers = { TC, 0, RR, RL, FC, 0, FR, FL } },
-+{ .ca_index = 0x23, .speakers = { TC, 0, RR, RL, FC, LFE, FR, FL } },
-+{ .ca_index = 0x24, .speakers = { FRH, FLH, RR, RL, 0, 0, FR, FL } },
-+{ .ca_index = 0x25, .speakers = { FRH, FLH, RR, RL, 0, LFE, FR, FL } },
-+{ .ca_index = 0x26, .speakers = { FRW, FLW, RR, RL, 0, 0, FR, FL } },
-+{ .ca_index = 0x27, .speakers = { FRW, FLW, RR, RL, 0, LFE, FR, FL } },
-+{ .ca_index = 0x28, .speakers = { TC, RC, RR, RL, FC, 0, FR, FL } },
-+{ .ca_index = 0x29, .speakers = { TC, RC, RR, RL, FC, LFE, FR, FL } },
-+{ .ca_index = 0x2a, .speakers = { FCH, RC, RR, RL, FC, 0, FR, FL } },
-+{ .ca_index = 0x2b, .speakers = { FCH, RC, RR, RL, FC, LFE, FR, FL } },
-+{ .ca_index = 0x2c, .speakers = { TC, FCH, RR, RL, FC, 0, FR, FL } },
-+{ .ca_index = 0x2d, .speakers = { TC, FCH, RR, RL, FC, LFE, FR, FL } },
-+{ .ca_index = 0x2e, .speakers = { FRH, FLH, RR, RL, FC, 0, FR, FL } },
-+{ .ca_index = 0x2f, .speakers = { FRH, FLH, RR, RL, FC, LFE, FR, FL } },
-+{ .ca_index = 0x30, .speakers = { FRW, FLW, RR, RL, FC, 0, FR, FL } },
-+{ .ca_index = 0x31, .speakers = { FRW, FLW, RR, RL, FC, LFE, FR, FL } },
-+};
-+
-+static int snd_bcm2835_chmap_ctl_tlv(struct snd_kcontrol *kcontrol, int op_flag,
-+ unsigned int size, unsigned int __user *tlv)
-+{
-+ unsigned int __user *dst;
-+ int count = 0;
-+ int i;
-+
-+ if (size < 8)
-+ return -ENOMEM;
-+ if (put_user(SNDRV_CTL_TLVT_CONTAINER, tlv))
-+ return -EFAULT;
-+ size -= 8;
-+ dst = tlv + 2;
-+ for (i = 0; i < ARRAY_SIZE(channel_allocations); i++) {
-+ struct cea_channel_speaker_allocation *ch = &channel_allocations[i];
-+ int num_chs = 0;
-+ int chs_bytes;
-+ int c;
-+
-+ for (c = 0; c < 8; c++) {
-+ if (ch->speakers[c])
-+ num_chs++;
-+ }
-+
-+ chs_bytes = num_chs * 4;
-+ if (size < 8)
-+ return -ENOMEM;
-+ if (put_user(SNDRV_CTL_TLVT_CHMAP_FIXED, dst) ||
-+ put_user(chs_bytes, dst + 1))
-+ return -EFAULT;
-+ dst += 2;
-+ size -= 8;
-+ count += 8;
-+ if (size < chs_bytes)
-+ return -ENOMEM;
-+ size -= chs_bytes;
-+ count += chs_bytes;
-+ for (c = 0; c < 8; c++) {
-+ int sp = ch->speakers[7 - c];
-+ if (sp) {
-+ if (put_user(sp, dst))
-+ return -EFAULT;
-+ dst++;
-+ }
-+ }
-+ }
-+ if (put_user(count, tlv + 1))
-+ return -EFAULT;
-+ return 0;
-+}
-+
-+static int snd_bcm2835_chmap_ctl_get(struct snd_kcontrol *kcontrol,
-+ struct snd_ctl_elem_value *ucontrol)
-+{
-+ struct snd_pcm_chmap *info = snd_kcontrol_chip(kcontrol);
-+ bcm2835_chip_t *chip = info->private_data;
-+ unsigned int idx = snd_ctl_get_ioffidx(kcontrol, &ucontrol->id);
-+ struct snd_pcm_substream *substream = snd_pcm_chmap_substream(info, idx);
-+ struct cea_channel_speaker_allocation *ch = NULL;
-+ int cur = 0;
-+ int i;
-+
-+ if (!substream || !substream->runtime)
-+ return -ENODEV;
-+
-+ for (i = 0; i < ARRAY_SIZE(channel_allocations); i++) {
-+ if (channel_allocations[i].ca_index == chip->cea_chmap)
-+ ch = &channel_allocations[i];
-+ }
-+
-+ /* If no layout was set yet, return a dummy. Apparently the userspace
-+ * API will be confused if we don't. */
-+ if (!ch)
-+ ch = &channel_allocations[0];
-+
-+ for (i = 0; i < 8; i++) {
-+ if (ch->speakers[7 - i])
-+ ucontrol->value.integer.value[cur++] = ch->speakers[7 - i];
-+ }
-+ while (cur < 8)
-+ ucontrol->value.integer.value[cur++] = SNDRV_CHMAP_NA;
-+ return 0;
-+}
-+
-+static int snd_bcm2835_chmap_ctl_put(struct snd_kcontrol *kcontrol,
-+ struct snd_ctl_elem_value *ucontrol)
-+{
-+ struct snd_pcm_chmap *info = snd_kcontrol_chip(kcontrol);
-+ bcm2835_chip_t *chip = info->private_data;
-+ unsigned int idx = snd_ctl_get_ioffidx(kcontrol, &ucontrol->id);
-+ struct snd_pcm_substream *substream = snd_pcm_chmap_substream(info, idx);
-+ int i, prepared = 0, cea_chmap = -1;
-+ int remap[8];
-+
-+ if (!substream || !substream->runtime)
-+ return -ENODEV;
-+
-+ switch (substream->runtime->status->state) {
-+ case SNDRV_PCM_STATE_OPEN:
-+ case SNDRV_PCM_STATE_SETUP:
-+ break;
-+ case SNDRV_PCM_STATE_PREPARED:
-+ prepared = 1;
-+ break;
-+ default:
-+ return -EBUSY;
-+ }
-+
-+ for (i = 0; i < ARRAY_SIZE(channel_allocations); i++) {
-+ struct cea_channel_speaker_allocation *ch = &channel_allocations[i];
-+ int matches = 1;
-+ int cur = 0;
-+ int x;
-+ memset(remap, 0, sizeof(remap));
-+ for (x = 0; x < substream->runtime->channels; x++) {
-+ int sp = ucontrol->value.integer.value[x];
-+ while (cur < 8 && !ch->speakers[7 - cur])
-+ cur++;
-+ if (cur >= 8) {
-+ /* user has more channels than ch */
-+ matches = 0;
-+ break;
-+ }
-+ if (ch->speakers[7 - cur] != sp) {
-+ matches = 0;
-+ break;
-+ }
-+ remap[x] = cur;
-+ cur++;
-+ }
-+ for (x = cur; x < 8; x++) {
-+ if (ch->speakers[7 - x]) {
-+ /* ch has more channels than user */
-+ matches = 0;
-+ break;
-+ }
-+ }
-+ if (matches) {
-+ cea_chmap = ch->ca_index;
-+ break;
-+ }
-+ }
-+
-+ if (cea_chmap < 0)
-+ return -EINVAL;
-+
-+ /* don't change the layout if another substream is active */
-+ if (chip->opened != (1 << substream->number) && chip->cea_chmap != cea_chmap)
-+ return -EBUSY; /* unsure whether this is a good error code */
-+
-+ chip->cea_chmap = cea_chmap;
-+ for (i = 0; i < 8; i++)
-+ chip->map_channels[i] = remap[i];
-+ if (prepared)
-+ snd_bcm2835_pcm_prepare_again(substream);
-+ return 0;
-+}
-+
-+static int snd_bcm2835_add_chmap_ctl(bcm2835_chip_t * chip)
-+{
-+ struct snd_pcm_chmap *chmap;
-+ struct snd_kcontrol *kctl;
-+ int err, i;
-+
-+ err = snd_pcm_add_chmap_ctls(chip->pcm,
-+ SNDRV_PCM_STREAM_PLAYBACK,
-+ NULL, 8, 0, &chmap);
-+ if (err < 0)
-+ return err;
-+ /* override handlers */
-+ chmap->private_data = chip;
-+ kctl = chmap->kctl;
-+ for (i = 0; i < kctl->count; i++)
-+ kctl->vd[i].access |= SNDRV_CTL_ELEM_ACCESS_WRITE;
-+ kctl->get = snd_bcm2835_chmap_ctl_get;
-+ kctl->put = snd_bcm2835_chmap_ctl_put;
-+ kctl->tlv.c = snd_bcm2835_chmap_ctl_tlv;
-+ return 0;
-+}
-+
- int snd_bcm2835_new_ctl(bcm2835_chip_t * chip)
- {
- int err;
-@@ -313,6 +588,7 @@ int snd_bcm2835_new_ctl(bcm2835_chip_t *
- if (err < 0)
- return err;
- }
-+ snd_bcm2835_add_chmap_ctl(chip);
- for (idx = 0; idx < ARRAY_SIZE(snd_bcm2835_spdif); idx++) {
- err = snd_ctl_add(chip->card,
- snd_ctl_new1(&snd_bcm2835_spdif[idx], chip));
---- a/sound/arm/bcm2835-pcm.c
-+++ b/sound/arm/bcm2835-pcm.c
-@@ -231,6 +231,9 @@ static int snd_bcm2835_playback_open_gen
-
- chip->alsa_stream[idx] = alsa_stream;
-
-+ if (!chip->opened)
-+ chip->cea_chmap = -1;
-+
- chip->opened |= (1 << idx);
- alsa_stream->open = 1;
- alsa_stream->draining = 1;
-@@ -341,8 +344,7 @@ static int snd_bcm2835_pcm_hw_free(struc
- return snd_pcm_lib_free_pages(substream);
- }
-
--/* prepare callback */
--static int snd_bcm2835_pcm_prepare(struct snd_pcm_substream *substream)
-+int snd_bcm2835_pcm_prepare_again(struct snd_pcm_substream *substream)
- {
- bcm2835_chip_t *chip = snd_pcm_substream_chip(substream);
- struct snd_pcm_runtime *runtime = substream->runtime;
-@@ -350,8 +352,6 @@ static int snd_bcm2835_pcm_prepare(struc
- int channels;
- int err;
-
-- audio_info(" .. IN\n");
--
- /* notify the vchiq that it should enter spdif passthrough mode by
- * setting channels=0 (see
- * https://github.com/raspberrypi/linux/issues/528) */
-@@ -367,6 +367,20 @@ static int snd_bcm2835_pcm_prepare(struc
- audio_error(" error setting hw params\n");
- }
-
-+ return err;
-+}
-+
-+/* prepare callback */
-+static int snd_bcm2835_pcm_prepare(struct snd_pcm_substream *substream)
-+{
-+ bcm2835_chip_t *chip = snd_pcm_substream_chip(substream);
-+ struct snd_pcm_runtime *runtime = substream->runtime;
-+ bcm2835_alsa_stream_t *alsa_stream = runtime->private_data;
-+
-+ audio_info(" .. IN\n");
-+
-+ snd_bcm2835_pcm_prepare_again(substream);
-+
- bcm2835_audio_setup(alsa_stream);
-
- /* in preparation of the stream, set the controls (volume level) of the stream */
---- a/sound/arm/bcm2835-vchiq.c
-+++ b/sound/arm/bcm2835-vchiq.c
-@@ -570,6 +570,8 @@ int bcm2835_audio_set_params(bcm2835_als
- VC_AUDIO_MSG_T m;
- AUDIO_INSTANCE_T *instance = alsa_stream->instance;
- int32_t success;
-+ uint32_t chmap_value;
-+ int i;
- int ret;
- LOG_DBG(" .. IN\n");
-
-@@ -593,10 +595,21 @@ int bcm2835_audio_set_params(bcm2835_als
-
- instance->result = -1;
-
-+ if (alsa_stream->chip->cea_chmap >= 0) {
-+ chmap_value = (unsigned)alsa_stream->chip->cea_chmap << 24;
-+ } else {
-+ chmap_value = 0; /* force stereo */
-+ for (i = 0; i < 8; i++)
-+ alsa_stream->chip->map_channels[i] = i;
-+ }
-+ for (i = 0; i < 8; i++)
-+ chmap_value |= alsa_stream->chip->map_channels[i] << (i * 3);
-+
- m.type = VC_AUDIO_MSG_TYPE_CONFIG;
- m.u.config.channels = channels;
- m.u.config.samplerate = samplerate;
- m.u.config.bps = bps;
-+ m.u.config.channelmap = chmap_value;
-
- /* Create the message available completion */
- init_completion(&instance->msg_avail_comp);
---- a/sound/arm/bcm2835.h
-+++ b/sound/arm/bcm2835.h
-@@ -107,6 +107,8 @@ typedef struct bcm2835_chip {
- int old_volume; /* stores the volume value whist muted */
- int dest;
- int mute;
-+ int cea_chmap; /* currently requested Audio InfoFrame Data Byte 4 */
-+ int map_channels[8];
-
- unsigned int opened;
- unsigned int spdif_status;
-@@ -149,6 +151,8 @@ int snd_bcm2835_new_ctl(bcm2835_chip_t *
- int snd_bcm2835_new_pcm(bcm2835_chip_t * chip);
- int snd_bcm2835_new_spdif_pcm(bcm2835_chip_t * chip);
-
-+int snd_bcm2835_pcm_prepare_again(struct snd_pcm_substream *substream);
-+
- int bcm2835_audio_open(bcm2835_alsa_stream_t * alsa_stream);
- int bcm2835_audio_close(bcm2835_alsa_stream_t * alsa_stream);
- int bcm2835_audio_set_params(bcm2835_alsa_stream_t * alsa_stream,
diff --git a/target/linux/brcm2708/patches-4.4/0130-bcm2835-access-controls-under-the-audio-mutex.patch b/target/linux/brcm2708/patches-4.4/0130-bcm2835-access-controls-under-the-audio-mutex.patch
deleted file mode 100644
index ee41e8d..0000000
--- a/target/linux/brcm2708/patches-4.4/0130-bcm2835-access-controls-under-the-audio-mutex.patch
+++ /dev/null
@@ -1,237 +0,0 @@
-From b88f8bdd254f5afd9284c7d75d10d4952c6dd9a4 Mon Sep 17 00:00:00 2001
-From: wm4 <wm4 at nowhere>
-Date: Wed, 13 Jan 2016 19:43:35 +0100
-Subject: [PATCH] bcm2835: access controls under the audio mutex
-
-I don't think the ALSA framework provides any kind of automatic
-synchronization within the control callbacks. We most likely need
-to ensure this manually, so add locking around all access to shared
-mutable data. In particular, bcm2835_audio_set_ctls() should
-probably always be called under our own audio lock.
----
- sound/arm/bcm2835-ctl.c | 74 +++++++++++++++++++++++++++++++++++++++++--------
- sound/arm/bcm2835-pcm.c | 4 +++
- 2 files changed, 66 insertions(+), 12 deletions(-)
-
---- a/sound/arm/bcm2835-ctl.c
-+++ b/sound/arm/bcm2835-ctl.c
-@@ -94,6 +94,9 @@ static int snd_bcm2835_ctl_get(struct sn
- {
- struct bcm2835_chip *chip = snd_kcontrol_chip(kcontrol);
-
-+ if (mutex_lock_interruptible(&chip->audio_mutex))
-+ return -EINTR;
-+
- BUG_ON(!chip && !(chip->avail_substreams & AVAIL_SUBSTREAMS_MASK));
-
- if (kcontrol->private_value == PCM_PLAYBACK_VOLUME)
-@@ -103,6 +106,7 @@ static int snd_bcm2835_ctl_get(struct sn
- else if (kcontrol->private_value == PCM_PLAYBACK_DEVICE)
- ucontrol->value.integer.value[0] = chip->dest;
-
-+ mutex_unlock(&chip->audio_mutex);
- return 0;
- }
-
-@@ -112,11 +116,15 @@ static int snd_bcm2835_ctl_put(struct sn
- struct bcm2835_chip *chip = snd_kcontrol_chip(kcontrol);
- int changed = 0;
-
-+ if (mutex_lock_interruptible(&chip->audio_mutex))
-+ return -EINTR;
-+
- if (kcontrol->private_value == PCM_PLAYBACK_VOLUME) {
- audio_info("Volume change attempted.. volume = %d new_volume = %d\n", chip->volume, (int)ucontrol->value.integer.value[0]);
- if (chip->mute == CTRL_VOL_MUTE) {
- /* changed = toggle_mute(chip, CTRL_VOL_UNMUTE); */
-- return 1; /* should return 0 to signify no change but the mixer takes this as the opposite sign (no idea why) */
-+ changed = 1; /* should return 0 to signify no change but the mixer takes this as the opposite sign (no idea why) */
-+ goto unlock;
- }
- if (changed
- || (ucontrol->value.integer.value[0] != chip2alsa(chip->volume))) {
-@@ -142,6 +150,8 @@ static int snd_bcm2835_ctl_put(struct sn
- printk(KERN_ERR "Failed to set ALSA controls..\n");
- }
-
-+unlock:
-+ mutex_unlock(&chip->audio_mutex);
- return changed;
- }
-
-@@ -198,10 +208,14 @@ static int snd_bcm2835_spdif_default_get
- struct bcm2835_chip *chip = snd_kcontrol_chip(kcontrol);
- int i;
-
-+ if (mutex_lock_interruptible(&chip->audio_mutex))
-+ return -EINTR;
-+
- for (i = 0; i < 4; i++)
- ucontrol->value.iec958.status[i] =
- (chip->spdif_status >> (i * 8)) && 0xff;
-
-+ mutex_unlock(&chip->audio_mutex);
- return 0;
- }
-
-@@ -212,12 +226,16 @@ static int snd_bcm2835_spdif_default_put
- unsigned int val = 0;
- int i, change;
-
-+ if (mutex_lock_interruptible(&chip->audio_mutex))
-+ return -EINTR;
-+
- for (i = 0; i < 4; i++)
- val |= (unsigned int)ucontrol->value.iec958.status[i] << (i * 8);
-
- change = val != chip->spdif_status;
- chip->spdif_status = val;
-
-+ mutex_unlock(&chip->audio_mutex);
- return change;
- }
-
-@@ -253,9 +271,14 @@ static int snd_bcm2835_spdif_stream_get(
- struct bcm2835_chip *chip = snd_kcontrol_chip(kcontrol);
- int i;
-
-+ if (mutex_lock_interruptible(&chip->audio_mutex))
-+ return -EINTR;
-+
- for (i = 0; i < 4; i++)
- ucontrol->value.iec958.status[i] =
- (chip->spdif_status >> (i * 8)) & 0xff;
-+
-+ mutex_unlock(&chip->audio_mutex);
- return 0;
- }
-
-@@ -266,11 +289,15 @@ static int snd_bcm2835_spdif_stream_put(
- unsigned int val = 0;
- int i, change;
-
-+ if (mutex_lock_interruptible(&chip->audio_mutex))
-+ return -EINTR;
-+
- for (i = 0; i < 4; i++)
- val |= (unsigned int)ucontrol->value.iec958.status[i] << (i * 8);
- change = val != chip->spdif_status;
- chip->spdif_status = val;
-
-+ mutex_unlock(&chip->audio_mutex);
- return change;
- }
-
-@@ -454,11 +481,17 @@ static int snd_bcm2835_chmap_ctl_get(str
- unsigned int idx = snd_ctl_get_ioffidx(kcontrol, &ucontrol->id);
- struct snd_pcm_substream *substream = snd_pcm_chmap_substream(info, idx);
- struct cea_channel_speaker_allocation *ch = NULL;
-+ int res = 0;
- int cur = 0;
- int i;
-
-- if (!substream || !substream->runtime)
-- return -ENODEV;
-+ if (mutex_lock_interruptible(&chip->audio_mutex))
-+ return -EINTR;
-+
-+ if (!substream || !substream->runtime) {
-+ res = -ENODEV;
-+ goto unlock;
-+ }
-
- for (i = 0; i < ARRAY_SIZE(channel_allocations); i++) {
- if (channel_allocations[i].ca_index == chip->cea_chmap)
-@@ -476,7 +509,10 @@ static int snd_bcm2835_chmap_ctl_get(str
- }
- while (cur < 8)
- ucontrol->value.integer.value[cur++] = SNDRV_CHMAP_NA;
-- return 0;
-+
-+unlock:
-+ mutex_unlock(&chip->audio_mutex);
-+ return res;
- }
-
- static int snd_bcm2835_chmap_ctl_put(struct snd_kcontrol *kcontrol,
-@@ -487,10 +523,16 @@ static int snd_bcm2835_chmap_ctl_put(str
- unsigned int idx = snd_ctl_get_ioffidx(kcontrol, &ucontrol->id);
- struct snd_pcm_substream *substream = snd_pcm_chmap_substream(info, idx);
- int i, prepared = 0, cea_chmap = -1;
-+ int res = 0;
- int remap[8];
-
-- if (!substream || !substream->runtime)
-- return -ENODEV;
-+ if (mutex_lock_interruptible(&chip->audio_mutex))
-+ return -EINTR;
-+
-+ if (!substream || !substream->runtime) {
-+ res = -ENODEV;
-+ goto unlock;
-+ }
-
- switch (substream->runtime->status->state) {
- case SNDRV_PCM_STATE_OPEN:
-@@ -500,7 +542,8 @@ static int snd_bcm2835_chmap_ctl_put(str
- prepared = 1;
- break;
- default:
-- return -EBUSY;
-+ res = -EBUSY;
-+ goto unlock;
- }
-
- for (i = 0; i < ARRAY_SIZE(channel_allocations); i++) {
-@@ -538,19 +581,26 @@ static int snd_bcm2835_chmap_ctl_put(str
- }
- }
-
-- if (cea_chmap < 0)
-- return -EINVAL;
-+ if (cea_chmap < 0) {
-+ res = -EINVAL;
-+ goto unlock;
-+ }
-
- /* don't change the layout if another substream is active */
-- if (chip->opened != (1 << substream->number) && chip->cea_chmap != cea_chmap)
-- return -EBUSY; /* unsure whether this is a good error code */
-+ if (chip->opened != (1 << substream->number) && chip->cea_chmap != cea_chmap) {
-+ res = -EBUSY; /* unsure whether this is a good error code */
-+ goto unlock;
-+ }
-
- chip->cea_chmap = cea_chmap;
- for (i = 0; i < 8; i++)
- chip->map_channels[i] = remap[i];
- if (prepared)
- snd_bcm2835_pcm_prepare_again(substream);
-- return 0;
-+
-+unlock:
-+ mutex_unlock(&chip->audio_mutex);
-+ return res;
- }
-
- static int snd_bcm2835_add_chmap_ctl(bcm2835_chip_t * chip)
---- a/sound/arm/bcm2835-pcm.c
-+++ b/sound/arm/bcm2835-pcm.c
-@@ -379,6 +379,9 @@ static int snd_bcm2835_pcm_prepare(struc
-
- audio_info(" .. IN\n");
-
-+ if (mutex_lock_interruptible(&chip->audio_mutex))
-+ return -EINTR;
-+
- snd_bcm2835_pcm_prepare_again(substream);
-
- bcm2835_audio_setup(alsa_stream);
-@@ -401,6 +404,7 @@ static int snd_bcm2835_pcm_prepare(struc
- alsa_stream->buffer_size, alsa_stream->period_size,
- alsa_stream->pos, runtime->frame_bits);
-
-+ mutex_unlock(&chip->audio_mutex);
- audio_info(" .. OUT\n");
- return 0;
- }
diff --git a/target/linux/brcm2708/patches-4.4/0131-bcm2835-always-use-2-4-8-channels-for-multichannel-l.patch b/target/linux/brcm2708/patches-4.4/0131-bcm2835-always-use-2-4-8-channels-for-multichannel-l.patch
deleted file mode 100644
index c30b219..0000000
--- a/target/linux/brcm2708/patches-4.4/0131-bcm2835-always-use-2-4-8-channels-for-multichannel-l.patch
+++ /dev/null
@@ -1,138 +0,0 @@
-From 8014377b2bffac1297ec920e45d8dcd1e74919cf Mon Sep 17 00:00:00 2001
-From: wm4 <wm4 at nowhere>
-Date: Wed, 13 Jan 2016 19:44:03 +0100
-Subject: [PATCH] bcm2835: always use 2/4/8 channels for multichannel layouts
-
-Pad the unused channels with NA. This means userspace needs to write
-additional, silent padding channels, which is not ideal, but better
-than noise.
-
-Works around noise at the following channel counts: 3, 5, 6, 7
----
- sound/arm/bcm2835-ctl.c | 89 +++++++++++++++++++++++++------------------------
- 1 file changed, 45 insertions(+), 44 deletions(-)
-
---- a/sound/arm/bcm2835-ctl.c
-+++ b/sound/arm/bcm2835-ctl.c
-@@ -349,6 +349,7 @@ struct cea_channel_speaker_allocation {
- #define FRW SNDRV_CHMAP_FRW
- #define TC SNDRV_CHMAP_TC
- #define FCH SNDRV_CHMAP_TFC
-+#define NA SNDRV_CHMAP_NA
-
- /*
- * CEA-861 channel maps
-@@ -356,69 +357,69 @@ struct cea_channel_speaker_allocation {
- * Stolen from sound/pci/hda/patch_hdmi.c
- * (unlike the source, this uses SNDRV_* constants directly, as by the
- * map_tables array in patch_hdmi.c)
-- * Unknown entries use 0, which unfortunately is SNDRV_CHMAP_UNKNOWN instead
-- * of SNDRV_CHMAP_NA.
-+ * Entries which do not have a physical output channel use 0. Entries which
-+ * require userspace to output silence use NA (SNDRV_CHMAP_NA).
- */
- static struct cea_channel_speaker_allocation channel_allocations[] = {
- /* channel: 7 6 5 4 3 2 1 0 */
- { .ca_index = 0x00, .speakers = { 0, 0, 0, 0, 0, 0, FR, FL } },
- /* 2.1 */
--{ .ca_index = 0x01, .speakers = { 0, 0, 0, 0, 0, LFE, FR, FL } },
-+{ .ca_index = 0x01, .speakers = { 0, 0, 0, 0, NA, LFE, FR, FL } },
- /* Dolby Surround */
--{ .ca_index = 0x02, .speakers = { 0, 0, 0, 0, FC, 0, FR, FL } },
-+{ .ca_index = 0x02, .speakers = { 0, 0, 0, 0, FC, NA, FR, FL } },
- /* surround40 */
--{ .ca_index = 0x08, .speakers = { 0, 0, RR, RL, 0, 0, FR, FL } },
-+{ .ca_index = 0x08, .speakers = { NA, NA, RR, RL, NA, NA, FR, FL } },
- /* surround41 */
--{ .ca_index = 0x09, .speakers = { 0, 0, RR, RL, 0, LFE, FR, FL } },
-+{ .ca_index = 0x09, .speakers = { NA, NA, RR, RL, NA, LFE, FR, FL } },
- /* surround50 */
--{ .ca_index = 0x0a, .speakers = { 0, 0, RR, RL, FC, 0, FR, FL } },
-+{ .ca_index = 0x0a, .speakers = { NA, NA, RR, RL, FC, NA, FR, FL } },
- /* surround51 */
--{ .ca_index = 0x0b, .speakers = { 0, 0, RR, RL, FC, LFE, FR, FL } },
-+{ .ca_index = 0x0b, .speakers = { NA, NA, RR, RL, FC, LFE, FR, FL } },
- /* 6.1 */
--{ .ca_index = 0x0f, .speakers = { 0, RC, RR, RL, FC, LFE, FR, FL } },
-+{ .ca_index = 0x0f, .speakers = { NA, RC, RR, RL, FC, LFE, FR, FL } },
- /* surround71 */
- { .ca_index = 0x13, .speakers = { RRC, RLC, RR, RL, FC, LFE, FR, FL } },
-
--{ .ca_index = 0x03, .speakers = { 0, 0, 0, 0, FC, LFE, FR, FL } },
--{ .ca_index = 0x04, .speakers = { 0, 0, 0, RC, 0, 0, FR, FL } },
--{ .ca_index = 0x05, .speakers = { 0, 0, 0, RC, 0, LFE, FR, FL } },
--{ .ca_index = 0x06, .speakers = { 0, 0, 0, RC, FC, 0, FR, FL } },
--{ .ca_index = 0x07, .speakers = { 0, 0, 0, RC, FC, LFE, FR, FL } },
--{ .ca_index = 0x0c, .speakers = { 0, RC, RR, RL, 0, 0, FR, FL } },
--{ .ca_index = 0x0d, .speakers = { 0, RC, RR, RL, 0, LFE, FR, FL } },
--{ .ca_index = 0x0e, .speakers = { 0, RC, RR, RL, FC, 0, FR, FL } },
--{ .ca_index = 0x10, .speakers = { RRC, RLC, RR, RL, 0, 0, FR, FL } },
--{ .ca_index = 0x11, .speakers = { RRC, RLC, RR, RL, 0, LFE, FR, FL } },
--{ .ca_index = 0x12, .speakers = { RRC, RLC, RR, RL, FC, 0, FR, FL } },
--{ .ca_index = 0x14, .speakers = { FRC, FLC, 0, 0, 0, 0, FR, FL } },
--{ .ca_index = 0x15, .speakers = { FRC, FLC, 0, 0, 0, LFE, FR, FL } },
--{ .ca_index = 0x16, .speakers = { FRC, FLC, 0, 0, FC, 0, FR, FL } },
--{ .ca_index = 0x17, .speakers = { FRC, FLC, 0, 0, FC, LFE, FR, FL } },
--{ .ca_index = 0x18, .speakers = { FRC, FLC, 0, RC, 0, 0, FR, FL } },
--{ .ca_index = 0x19, .speakers = { FRC, FLC, 0, RC, 0, LFE, FR, FL } },
--{ .ca_index = 0x1a, .speakers = { FRC, FLC, 0, RC, FC, 0, FR, FL } },
--{ .ca_index = 0x1b, .speakers = { FRC, FLC, 0, RC, FC, LFE, FR, FL } },
--{ .ca_index = 0x1c, .speakers = { FRC, FLC, RR, RL, 0, 0, FR, FL } },
--{ .ca_index = 0x1d, .speakers = { FRC, FLC, RR, RL, 0, LFE, FR, FL } },
--{ .ca_index = 0x1e, .speakers = { FRC, FLC, RR, RL, FC, 0, FR, FL } },
-+{ .ca_index = 0x03, .speakers = { NA, NA, NA, NA, FC, LFE, FR, FL } },
-+{ .ca_index = 0x04, .speakers = { NA, NA, NA, RC, NA, NA, FR, FL } },
-+{ .ca_index = 0x05, .speakers = { NA, NA, NA, RC, NA, LFE, FR, FL } },
-+{ .ca_index = 0x06, .speakers = { NA, NA, NA, RC, FC, NA, FR, FL } },
-+{ .ca_index = 0x07, .speakers = { NA, NA, NA, RC, FC, LFE, FR, FL } },
-+{ .ca_index = 0x0c, .speakers = { NA, RC, RR, RL, NA, NA, FR, FL } },
-+{ .ca_index = 0x0d, .speakers = { NA, RC, RR, RL, NA, LFE, FR, FL } },
-+{ .ca_index = 0x0e, .speakers = { NA, RC, RR, RL, FC, NA, FR, FL } },
-+{ .ca_index = 0x10, .speakers = { RRC, RLC, RR, RL, NA, NA, FR, FL } },
-+{ .ca_index = 0x11, .speakers = { RRC, RLC, RR, RL, NA, LFE, FR, FL } },
-+{ .ca_index = 0x12, .speakers = { RRC, RLC, RR, RL, FC, NA, FR, FL } },
-+{ .ca_index = 0x14, .speakers = { FRC, FLC, NA, NA, NA, NA, FR, FL } },
-+{ .ca_index = 0x15, .speakers = { FRC, FLC, NA, NA, NA, LFE, FR, FL } },
-+{ .ca_index = 0x16, .speakers = { FRC, FLC, NA, NA, FC, NA, FR, FL } },
-+{ .ca_index = 0x17, .speakers = { FRC, FLC, NA, NA, FC, LFE, FR, FL } },
-+{ .ca_index = 0x18, .speakers = { FRC, FLC, NA, RC, NA, NA, FR, FL } },
-+{ .ca_index = 0x19, .speakers = { FRC, FLC, NA, RC, NA, LFE, FR, FL } },
-+{ .ca_index = 0x1a, .speakers = { FRC, FLC, NA, RC, FC, NA, FR, FL } },
-+{ .ca_index = 0x1b, .speakers = { FRC, FLC, NA, RC, FC, LFE, FR, FL } },
-+{ .ca_index = 0x1c, .speakers = { FRC, FLC, RR, RL, NA, NA, FR, FL } },
-+{ .ca_index = 0x1d, .speakers = { FRC, FLC, RR, RL, NA, LFE, FR, FL } },
-+{ .ca_index = 0x1e, .speakers = { FRC, FLC, RR, RL, FC, NA, FR, FL } },
- { .ca_index = 0x1f, .speakers = { FRC, FLC, RR, RL, FC, LFE, FR, FL } },
--{ .ca_index = 0x20, .speakers = { 0, FCH, RR, RL, FC, 0, FR, FL } },
--{ .ca_index = 0x21, .speakers = { 0, FCH, RR, RL, FC, LFE, FR, FL } },
--{ .ca_index = 0x22, .speakers = { TC, 0, RR, RL, FC, 0, FR, FL } },
--{ .ca_index = 0x23, .speakers = { TC, 0, RR, RL, FC, LFE, FR, FL } },
--{ .ca_index = 0x24, .speakers = { FRH, FLH, RR, RL, 0, 0, FR, FL } },
--{ .ca_index = 0x25, .speakers = { FRH, FLH, RR, RL, 0, LFE, FR, FL } },
--{ .ca_index = 0x26, .speakers = { FRW, FLW, RR, RL, 0, 0, FR, FL } },
--{ .ca_index = 0x27, .speakers = { FRW, FLW, RR, RL, 0, LFE, FR, FL } },
--{ .ca_index = 0x28, .speakers = { TC, RC, RR, RL, FC, 0, FR, FL } },
-+{ .ca_index = 0x20, .speakers = { NA, FCH, RR, RL, FC, NA, FR, FL } },
-+{ .ca_index = 0x21, .speakers = { NA, FCH, RR, RL, FC, LFE, FR, FL } },
-+{ .ca_index = 0x22, .speakers = { TC, NA, RR, RL, FC, NA, FR, FL } },
-+{ .ca_index = 0x23, .speakers = { TC, NA, RR, RL, FC, LFE, FR, FL } },
-+{ .ca_index = 0x24, .speakers = { FRH, FLH, RR, RL, NA, NA, FR, FL } },
-+{ .ca_index = 0x25, .speakers = { FRH, FLH, RR, RL, NA, LFE, FR, FL } },
-+{ .ca_index = 0x26, .speakers = { FRW, FLW, RR, RL, NA, NA, FR, FL } },
-+{ .ca_index = 0x27, .speakers = { FRW, FLW, RR, RL, NA, LFE, FR, FL } },
-+{ .ca_index = 0x28, .speakers = { TC, RC, RR, RL, FC, NA, FR, FL } },
- { .ca_index = 0x29, .speakers = { TC, RC, RR, RL, FC, LFE, FR, FL } },
--{ .ca_index = 0x2a, .speakers = { FCH, RC, RR, RL, FC, 0, FR, FL } },
-+{ .ca_index = 0x2a, .speakers = { FCH, RC, RR, RL, FC, NA, FR, FL } },
- { .ca_index = 0x2b, .speakers = { FCH, RC, RR, RL, FC, LFE, FR, FL } },
--{ .ca_index = 0x2c, .speakers = { TC, FCH, RR, RL, FC, 0, FR, FL } },
-+{ .ca_index = 0x2c, .speakers = { TC, FCH, RR, RL, FC, NA, FR, FL } },
- { .ca_index = 0x2d, .speakers = { TC, FCH, RR, RL, FC, LFE, FR, FL } },
--{ .ca_index = 0x2e, .speakers = { FRH, FLH, RR, RL, FC, 0, FR, FL } },
-+{ .ca_index = 0x2e, .speakers = { FRH, FLH, RR, RL, FC, NA, FR, FL } },
- { .ca_index = 0x2f, .speakers = { FRH, FLH, RR, RL, FC, LFE, FR, FL } },
--{ .ca_index = 0x30, .speakers = { FRW, FLW, RR, RL, FC, 0, FR, FL } },
-+{ .ca_index = 0x30, .speakers = { FRW, FLW, RR, RL, FC, NA, FR, FL } },
- { .ca_index = 0x31, .speakers = { FRW, FLW, RR, RL, FC, LFE, FR, FL } },
- };
-
diff --git a/target/linux/brcm2708/patches-4.4/0132-bcm2835-only-allow-stereo-if-analogue-jack-is-select.patch b/target/linux/brcm2708/patches-4.4/0132-bcm2835-only-allow-stereo-if-analogue-jack-is-select.patch
deleted file mode 100644
index 77798d5..0000000
--- a/target/linux/brcm2708/patches-4.4/0132-bcm2835-only-allow-stereo-if-analogue-jack-is-select.patch
+++ /dev/null
@@ -1,61 +0,0 @@
-From 55f46d3887656ffb67c61cd9b44599c4cdfc65c7 Mon Sep 17 00:00:00 2001
-From: wm4 <wm4 at nowhere>
-Date: Wed, 13 Jan 2016 19:44:24 +0100
-Subject: [PATCH] bcm2835: only allow stereo if analogue jack is selected
-
-Sending more than 2 channels to videocore while outputting to analogue
-mysteriously outputs heavy artifacts. So just paint it over with a
-hack: if analogue is explicitly selected as destination, do not
-reporting support for anything other than stereo.
-
-I'm not sure how to deal with the auto case (destination 0). There's
-probably way to retrieve this and even to listen to plug events, but
-I didn't find one yet, and it's probably not worth the trouble. Just
-don't use this setting, I guess. Unless you like noise.
-
-Changing the setting while an audio stream is active also doesn't
-work properly. We could probably interrupt running streams by
-returning ENODEV or using kernel hotplug stuff (maybe), but that
-also doesn't seem worth the trouble.
----
- sound/arm/bcm2835-ctl.c | 12 ++++++++++++
- 1 file changed, 12 insertions(+)
-
---- a/sound/arm/bcm2835-ctl.c
-+++ b/sound/arm/bcm2835-ctl.c
-@@ -423,9 +423,16 @@ static struct cea_channel_speaker_alloca
- { .ca_index = 0x31, .speakers = { FRW, FLW, RR, RL, FC, LFE, FR, FL } },
- };
-
-+static int uses_analogue(bcm2835_chip_t *chip)
-+{
-+ return chip->dest == 1;
-+}
-+
- static int snd_bcm2835_chmap_ctl_tlv(struct snd_kcontrol *kcontrol, int op_flag,
- unsigned int size, unsigned int __user *tlv)
- {
-+ struct snd_pcm_chmap *info = snd_kcontrol_chip(kcontrol);
-+ bcm2835_chip_t *chip = info->private_data;
- unsigned int __user *dst;
- int count = 0;
- int i;
-@@ -442,6 +449,9 @@ static int snd_bcm2835_chmap_ctl_tlv(str
- int chs_bytes;
- int c;
-
-+ if (i > 0 && uses_analogue(chip))
-+ break;
-+
- for (c = 0; c < 8; c++) {
- if (ch->speakers[c])
- num_chs++;
-@@ -552,6 +562,8 @@ static int snd_bcm2835_chmap_ctl_put(str
- int matches = 1;
- int cur = 0;
- int x;
-+ if (i > 0 && uses_analogue(chip))
-+ break;
- memset(remap, 0, sizeof(remap));
- for (x = 0; x < substream->runtime->channels; x++) {
- int sp = ucontrol->value.integer.value[x];
diff --git a/target/linux/brcm2708/patches-4.4/0133-bcm2835-interpolate-audio-delay.patch b/target/linux/brcm2708/patches-4.4/0133-bcm2835-interpolate-audio-delay.patch
deleted file mode 100644
index 8bf1ad8..0000000
--- a/target/linux/brcm2708/patches-4.4/0133-bcm2835-interpolate-audio-delay.patch
+++ /dev/null
@@ -1,90 +0,0 @@
-From a94c77d797c554678a37fb2b921fbab46f7f205e Mon Sep 17 00:00:00 2001
-From: wm4 <wm4 at nowhere>
-Date: Wed, 13 Jan 2016 19:44:47 +0100
-Subject: [PATCH] bcm2835: interpolate audio delay
-
-It appears the GPU only sends us a message all 10ms to update
-the playback progress. Other than this, the playback position
-(what SNDRV_PCM_IOCTL_DELAY will return) is not updated at all.
-Userspace will see jitter up to 10ms in the audio position.
-
-Make this a bit nicer for userspace by interpolating the
-position using the CPU clock.
-
-I'm not sure if setting snd_pcm_runtime.delay is the right
-approach for this. Or if there is maybe an already existing
-mechanism for position interpolation in the ALSA core.
-
-I only set SNDRV_PCM_INFO_BATCH because this appears to remove
-at least one situation snd_pcm_runtime.delay is used, so I have
-to worry less in which place I have to update this field, or
-how it interacts with the rest of ALSA.
-
-In the future, it might be nice to use VC_AUDIO_MSG_TYPE_LATENCY.
-One problem is that it requires sending a videocore message, and
-waiting for a reply, which could make the implementation much
-harder due to locking and synchronization requirements.
----
- sound/arm/bcm2835-pcm.c | 12 +++++++++++-
- sound/arm/bcm2835.h | 1 +
- 2 files changed, 12 insertions(+), 1 deletion(-)
-
---- a/sound/arm/bcm2835-pcm.c
-+++ b/sound/arm/bcm2835-pcm.c
-@@ -25,7 +25,7 @@
- /* hardware definition */
- static struct snd_pcm_hardware snd_bcm2835_playback_hw = {
- .info = (SNDRV_PCM_INFO_INTERLEAVED | SNDRV_PCM_INFO_BLOCK_TRANSFER |
-- SNDRV_PCM_INFO_MMAP | SNDRV_PCM_INFO_MMAP_VALID),
-+ SNDRV_PCM_INFO_MMAP | SNDRV_PCM_INFO_MMAP_VALID | SNDRV_PCM_INFO_BATCH),
- .formats = SNDRV_PCM_FMTBIT_U8 | SNDRV_PCM_FMTBIT_S16_LE,
- .rates = SNDRV_PCM_RATE_CONTINUOUS | SNDRV_PCM_RATE_8000_48000,
- .rate_min = 8000,
-@@ -99,6 +99,8 @@ static irqreturn_t bcm2835_playback_fifo
- alsa_stream->pos %= alsa_stream->buffer_size;
- }
-
-+ alsa_stream->interpolate_start = ktime_get_ns();
-+
- if (alsa_stream->substream) {
- if (new_period)
- snd_pcm_period_elapsed(alsa_stream->substream);
-@@ -399,6 +401,7 @@ static int snd_bcm2835_pcm_prepare(struc
- alsa_stream->buffer_size = snd_pcm_lib_buffer_bytes(substream);
- alsa_stream->period_size = snd_pcm_lib_period_bytes(substream);
- alsa_stream->pos = 0;
-+ alsa_stream->interpolate_start = ktime_get_ns();
-
- audio_debug("buffer_size=%d, period_size=%d pos=%d frame_bits=%d\n",
- alsa_stream->buffer_size, alsa_stream->period_size,
-@@ -495,6 +498,7 @@ snd_bcm2835_pcm_pointer(struct snd_pcm_s
- {
- struct snd_pcm_runtime *runtime = substream->runtime;
- bcm2835_alsa_stream_t *alsa_stream = runtime->private_data;
-+ u64 now = ktime_get_ns();
-
- audio_info(" .. IN\n");
-
-@@ -503,6 +507,12 @@ snd_bcm2835_pcm_pointer(struct snd_pcm_s
- frames_to_bytes(runtime, runtime->control->appl_ptr),
- alsa_stream->pos);
-
-+ /* Give userspace better delay reporting by interpolating between GPU
-+ * notifications, assuming audio speed is close enough to the clock
-+ * used for ktime */
-+ if (alsa_stream->interpolate_start && alsa_stream->interpolate_start < now)
-+ runtime->delay = -(int)div_u64((now - alsa_stream->interpolate_start) * runtime->rate, 1000000000);
-+
- audio_info(" .. OUT\n");
- return snd_pcm_indirect_playback_pointer(substream,
- &alsa_stream->pcm_indirect,
---- a/sound/arm/bcm2835.h
-+++ b/sound/arm/bcm2835.h
-@@ -137,6 +137,7 @@ typedef struct bcm2835_alsa_stream {
- unsigned int pos;
- unsigned int buffer_size;
- unsigned int period_size;
-+ u64 interpolate_start;
-
- uint32_t enable_fifo_irq;
- irq_handler_t fifo_irq_handler;
diff --git a/target/linux/brcm2708/patches-4.4/0134-bcm2835-sdhost-Add-workaround-for-odd-behaviour-on-s.patch b/target/linux/brcm2708/patches-4.4/0134-bcm2835-sdhost-Add-workaround-for-odd-behaviour-on-s.patch
deleted file mode 100644
index 705eb77..0000000
--- a/target/linux/brcm2708/patches-4.4/0134-bcm2835-sdhost-Add-workaround-for-odd-behaviour-on-s.patch
+++ /dev/null
@@ -1,137 +0,0 @@
-From 2c8808d44f2555d0385082010a870a05ac888a5c Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Tue, 19 Jan 2016 17:16:38 +0000
-Subject: [PATCH] bcm2835-sdhost: Add workaround for odd behaviour on some
- cards
-
-For reasons not understood, the sdhost driver fails when reading
-sectors very near the end of some SD cards. The problem could
-be related to the similar issue that reading the final sector
-of any card as part of a multiple read never completes, and the
-workaround is an extension of the mechanism introduced to solve
-that problem which ensures those sectors are always read singly.
----
- drivers/mmc/host/bcm2835-sdhost.c | 61 +++++++++++++++++++++++++++++++++------
- 1 file changed, 52 insertions(+), 9 deletions(-)
-
---- a/drivers/mmc/host/bcm2835-sdhost.c
-+++ b/drivers/mmc/host/bcm2835-sdhost.c
-@@ -173,6 +173,9 @@ struct bcm2835_host {
- u32 overclock_50; /* frequency to use when 50MHz is requested (in MHz) */
- u32 overclock; /* Current frequency if overclocked, else zero */
- u32 pio_limit; /* Maximum block count for PIO (0 = always DMA) */
-+
-+ u32 sectors; /* Cached card size in sectors */
-+ u32 single_read_sectors[8];
- };
-
-
-@@ -277,6 +280,9 @@ static void bcm2835_sdhost_reset_interna
- {
- u32 temp;
-
-+ if (host->debug)
-+ pr_info("%s: reset\n", mmc_hostname(host->mmc));
-+
- bcm2835_sdhost_set_power(host, false);
-
- bcm2835_sdhost_write(host, 0, SDCMD);
-@@ -299,6 +305,8 @@ static void bcm2835_sdhost_reset_interna
- bcm2835_sdhost_set_power(host, true);
- mdelay(10);
- host->clock = 0;
-+ host->sectors = 0;
-+ host->single_read_sectors[0] = ~0;
- bcm2835_sdhost_write(host, host->hcfg, SDHCFG);
- bcm2835_sdhost_write(host, host->cdiv, SDCDIV);
- mmiowb();
-@@ -309,8 +317,6 @@ static void bcm2835_sdhost_reset(struct
- {
- struct bcm2835_host *host = mmc_priv(mmc);
- unsigned long flags;
-- if (host->debug)
-- pr_info("%s: reset\n", mmc_hostname(mmc));
- spin_lock_irqsave(&host->lock, flags);
-
- bcm2835_sdhost_reset_internal(host);
-@@ -676,6 +682,32 @@ static void bcm2835_sdhost_prepare_data(
- host->flush_fifo = 0;
- host->data->bytes_xfered = 0;
-
-+ if (!host->sectors && host->mmc->card)
-+ {
-+ struct mmc_card *card = host->mmc->card;
-+ if (!mmc_card_sd(card) && mmc_card_blockaddr(card)) {
-+ /*
-+ * The EXT_CSD sector count is in number of 512 byte
-+ * sectors.
-+ */
-+ host->sectors = card->ext_csd.sectors;
-+ pr_err("%s: using ext_csd!\n", mmc_hostname(host->mmc));
-+ } else {
-+ /*
-+ * The CSD capacity field is in units of read_blkbits.
-+ * set_capacity takes units of 512 bytes.
-+ */
-+ host->sectors = card->csd.capacity <<
-+ (card->csd.read_blkbits - 9);
-+ }
-+ host->single_read_sectors[0] = host->sectors - 65;
-+ host->single_read_sectors[1] = host->sectors - 64;
-+ host->single_read_sectors[2] = host->sectors - 33;
-+ host->single_read_sectors[3] = host->sectors - 32;
-+ host->single_read_sectors[4] = host->sectors - 1;
-+ host->single_read_sectors[5] = ~0; /* Safety net */
-+ }
-+
- host->use_dma = host->have_dma && (data->blocks > host->pio_limit);
- if (!host->use_dma) {
- int flags;
-@@ -1246,6 +1278,10 @@ static u32 bcm2835_sdhost_block_irq(stru
-
- bcm2835_sdhost_finish_data(host);
- } else {
-+ /* Reset the timer */
-+ mod_timer(&host->pio_timer,
-+ jiffies + host->pio_timeout);
-+
- bcm2835_sdhost_transfer_pio(host);
-
- /* Reset the timer */
-@@ -1450,8 +1486,8 @@ void bcm2835_sdhost_set_clock(struct bcm
- host->cdiv = div;
- bcm2835_sdhost_write(host, host->cdiv, SDCDIV);
-
-- /* Set the timeout to 500ms */
-- bcm2835_sdhost_write(host, host->mmc->actual_clock/2, SDTOUT);
-+ /* Set the timeout to 250ms */
-+ bcm2835_sdhost_write(host, host->mmc->actual_clock/4, SDTOUT);
-
- if (host->debug)
- pr_info("%s: clock=%d -> max_clk=%d, cdiv=%x (actual clock %d)\n",
-@@ -1566,13 +1602,20 @@ static int bcm2835_sdhost_multi_io_quirk
- reading the final sector of the card as part of a multiple read
- problematic. Detect that case and shorten the read accordingly.
- */
-- /* csd.capacity is in weird units - convert to sectors */
-- u32 card_sectors = (card->csd.capacity << (card->csd.read_blkbits - 9));
-+ struct bcm2835_host *host;
-+
-+ host = mmc_priv(card->host);
-
-- if ((direction == MMC_DATA_READ) &&
-- ((blk_pos + blk_size) == card_sectors))
-- blk_size--;
-+ if (direction == MMC_DATA_READ)
-+ {
-+ int i;
-+ int sector;
-+ for (i = 0; blk_pos > (sector = host->single_read_sectors[i]); i++)
-+ continue;
-
-+ if ((blk_pos + blk_size) > sector)
-+ blk_size = (blk_pos == sector) ? 1 : (sector - blk_pos);
-+ }
- return blk_size;
- }
-
diff --git a/target/linux/brcm2708/patches-4.4/0135-bcm2835-sdhost-Add-debug_flags-dtparam.patch b/target/linux/brcm2708/patches-4.4/0135-bcm2835-sdhost-Add-debug_flags-dtparam.patch
deleted file mode 100644
index e98710d..0000000
--- a/target/linux/brcm2708/patches-4.4/0135-bcm2835-sdhost-Add-debug_flags-dtparam.patch
+++ /dev/null
@@ -1,120 +0,0 @@
-From 99695e24b9c0d1b573846081c2f58ef3114a9f35 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 22 Jan 2016 16:03:24 +0000
-Subject: [PATCH] bcm2835-sdhost: Add debug_flags dtparam
-
-Bit zero disables the single-read-sectors map:
-
-If the default MMC driver is bcm2835-mmc:
- dtoverlay=sdhost,debug_flags=1
-If the default MMC driver is bcm2835-sdhost:
- dtoverlay=sdtweak,debug_flags=1
-(although the sdhost overlay may also work, sdtweak is
-less invasive and will work in more circumstances).
-
-Also revert the timeout change, just in case.
----
- arch/arm/boot/dts/overlays/sdhost-overlay.dts | 2 ++
- arch/arm/boot/dts/overlays/sdtweak-overlay.dts | 2 ++
- drivers/mmc/host/bcm2835-sdhost.c | 26 +++++++++++++++++++++-----
- 3 files changed, 25 insertions(+), 5 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/sdhost-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/sdhost-overlay.dts
-@@ -16,6 +16,7 @@
- frag1: __overlay__ {
- brcm,overclock-50 = <0>;
- brcm,pio-limit = <1>;
-+ brcm,debug-flags = <0>;
- status = "okay";
- };
- };
-@@ -25,5 +26,6 @@
- force_pio = <&frag1>,"brcm,force-pio?";
- pio_limit = <&frag1>,"brcm,pio-limit:0";
- debug = <&frag1>,"brcm,debug?";
-+ debug_flags = <&frag1>,"brcm,debug-flags:0";
- };
- };
---- a/arch/arm/boot/dts/overlays/sdtweak-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/sdtweak-overlay.dts
-@@ -9,6 +9,7 @@
- frag1: __overlay__ {
- brcm,overclock-50 = <0>;
- brcm,pio-limit = <1>;
-+ brcm,debug-flags = <0>;
- };
- };
-
-@@ -17,5 +18,6 @@
- force_pio = <&frag1>,"brcm,force-pio?";
- pio_limit = <&frag1>,"brcm,pio-limit:0";
- debug = <&frag1>,"brcm,debug?";
-+ debug_flags = <&frag1>,"brcm,debug-flags:0";
- };
- };
---- a/drivers/mmc/host/bcm2835-sdhost.c
-+++ b/drivers/mmc/host/bcm2835-sdhost.c
-@@ -174,6 +174,8 @@ struct bcm2835_host {
- u32 overclock; /* Current frequency if overclocked, else zero */
- u32 pio_limit; /* Maximum block count for PIO (0 = always DMA) */
-
-+ u32 debug_flags;
-+
- u32 sectors; /* Cached card size in sectors */
- u32 single_read_sectors[8];
- };
-@@ -682,7 +684,7 @@ static void bcm2835_sdhost_prepare_data(
- host->flush_fifo = 0;
- host->data->bytes_xfered = 0;
-
-- if (!host->sectors && host->mmc->card)
-+ if (!host->sectors && host->mmc->card && !(host->debug_flags & 1))
- {
- struct mmc_card *card = host->mmc->card;
- if (!mmc_card_sd(card) && mmc_card_blockaddr(card)) {
-@@ -1486,8 +1488,8 @@ void bcm2835_sdhost_set_clock(struct bcm
- host->cdiv = div;
- bcm2835_sdhost_write(host, host->cdiv, SDCDIV);
-
-- /* Set the timeout to 250ms */
-- bcm2835_sdhost_write(host, host->mmc->actual_clock/4, SDTOUT);
-+ /* Set the timeout to 500ms */
-+ bcm2835_sdhost_write(host, host->mmc->actual_clock/2, SDTOUT);
-
- if (host->debug)
- pr_info("%s: clock=%d -> max_clk=%d, cdiv=%x (actual clock %d)\n",
-@@ -1606,8 +1608,16 @@ static int bcm2835_sdhost_multi_io_quirk
-
- host = mmc_priv(card->host);
-
-- if (direction == MMC_DATA_READ)
-- {
-+ if (!host->sectors) {
-+ /* csd.capacity is in weird units - convert to sectors */
-+ u32 card_sectors = (card->csd.capacity << (card->csd.read_blkbits - 9));
-+ if ((direction == MMC_DATA_READ) &&
-+ ((blk_pos + blk_size) == card_sectors))
-+ blk_size--;
-+ return blk_size;
-+ }
-+
-+ if (direction == MMC_DATA_READ) {
- int i;
- int sector;
- for (i = 0; blk_pos > (sector = host->single_read_sectors[i]); i++)
-@@ -1838,8 +1848,14 @@ static int bcm2835_sdhost_probe(struct p
- host->allow_dma = ALLOW_DMA &&
- !of_property_read_bool(node, "brcm,force-pio");
- host->debug = of_property_read_bool(node, "brcm,debug");
-+ of_property_read_u32(node,
-+ "brcm,debug-flags",
-+ &host->debug_flags);
- }
-
-+ if (host->debug_flags)
-+ dev_err(dev, "debug_flags=%x\n", host->debug_flags);
-+
- if (host->allow_dma) {
- if (node) {
- host->dma_chan_tx =
diff --git a/target/linux/brcm2708/patches-4.4/0136-BCM270X_DT-Add-sdio_overclock-parameter-to-sdio-over.patch b/target/linux/brcm2708/patches-4.4/0136-BCM270X_DT-Add-sdio_overclock-parameter-to-sdio-over.patch
deleted file mode 100644
index 32f2b39..0000000
--- a/target/linux/brcm2708/patches-4.4/0136-BCM270X_DT-Add-sdio_overclock-parameter-to-sdio-over.patch
+++ /dev/null
@@ -1,68 +0,0 @@
-From 8f64930d900f31cff8bad07ae49059138f1cd46d Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 25 Jan 2016 09:12:06 +0000
-Subject: [PATCH] BCM270X_DT: Add sdio_overclock parameter to sdio overlay
-
-The sdio_overclock parameter is like the overclock_50 parameter, i.e.
-it sets an alternate frequency (in MHz) to use when the MMC framework
-requests 50MHz, except that it applies to the SDIO bus.
-
-Be aware that the actual frequencies achievable are limited to even integer
-divisions of 250MHz, and that the driver will round up to include fractions
-(e.g. 62 will include 62.5) but then round down to the nearest frequency.
-In other words, the chosen frequency is the highest possible that is less than
-the parameter value + 1. In practise this means that 62 is the only sensible
-value.
-
-Examples:
- 250MHz/4 = 62.5MHz (sdio_overclock=62)
- 250MHz/2 = 125MHz (sdio_overclock=125) # Too fast
----
- arch/arm/boot/dts/overlays/README | 9 ++++++---
- arch/arm/boot/dts/overlays/sdio-overlay.dts | 2 ++
- 2 files changed, 8 insertions(+), 3 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -53,8 +53,8 @@ have its contents deleted (or commented
- Using Overlays
- ==============
-
--Overlays are loaded using the "dtoverlay" directive. As an example, consider the
--popular lirc-rpi module, the Linux Infrared Remote Control driver. In the
-+Overlays are loaded using the "dtoverlay" directive. As an example, consider
-+the popular lirc-rpi module, the Linux Infrared Remote Control driver. In the
- pre-DT world this would be loaded from /etc/modules, with an explicit
- "modprobe lirc-rpi" command, or programmatically by lircd. With DT enabled,
- this becomes a line in config.txt:
-@@ -621,9 +621,12 @@ Name: sdio
- Info: Selects the bcm2835-sdhost SD/MMC driver, optionally with overclock,
- and enables SDIO via GPIOs 22-27.
- Load: dtoverlay=sdio,<param>=<val>
--Params: overclock_50 Clock (in MHz) to use when the MMC framework
-+Params: overclock_50 SD Clock (in MHz) to use when the MMC framework
- requests 50MHz
-
-+ sdio_overclock SDIO Clock (in MHz) to use when the MMC
-+ framework requests 50MHz
-+
- force_pio Disable DMA support (default off)
-
- pio_limit Number of blocks above which to use DMA
---- a/arch/arm/boot/dts/overlays/sdio-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/sdio-overlay.dts
-@@ -12,6 +12,7 @@
- pinctrl-0 = <&sdio_pins>;
- non-removable;
- bus-width = <4>;
-+ brcm,overclock-50 = <0>;
- status = "okay";
- };
- };
-@@ -30,5 +31,6 @@
- __overrides__ {
- poll_once = <&sdio_mmc>,"non-removable?";
- bus_width = <&sdio_mmc>,"bus-width:0";
-+ sdio_overclock = <&sdio_mmc>,"brcm,overclock-50:0";
- };
- };
diff --git a/target/linux/brcm2708/patches-4.4/0137-rtc-ds1307-add-support-for-the-DT-property-wakeup-so.patch b/target/linux/brcm2708/patches-4.4/0137-rtc-ds1307-add-support-for-the-DT-property-wakeup-so.patch
deleted file mode 100644
index 1c6f355..0000000
--- a/target/linux/brcm2708/patches-4.4/0137-rtc-ds1307-add-support-for-the-DT-property-wakeup-so.patch
+++ /dev/null
@@ -1,93 +0,0 @@
-From 52a2e460333eb84cf5afb3acff953b79487fd3ac Mon Sep 17 00:00:00 2001
-From: Michael Lange <linuxstuff at milaw.biz>
-Date: Thu, 21 Jan 2016 18:10:16 +0100
-Subject: [PATCH] rtc: ds1307: add support for the DT property 'wakeup-source'
-
-For RTC chips with no IRQ directly connected to the SoC, the RTC chip
-can be forced as a wakeup source by stating that explicitly in
-the device's .dts file using the "wakeup-source" boolean property.
-This will guarantee the 'wakealarm' sysfs entry is available on the
-device, if supported by the RTC.
-
-With these changes to the driver rtc-ds1307 and the necessary entries
-in the .dts file, I get an working ds1337 RTC on the Witty Pi extension
-board by UUGear for the Raspberry Pi.
-
-An example for the entry in the .dts file:
-
- rtc: ds1337 at 68 {
- compatible = "dallas,ds1337";
- reg = <0x68>;
- wakeup-source;
-
-If the "wakeup-source" property is set, do not request an IRQ.
-Set also UIE mode to unsupported, to get a working 'hwclock' binary.
-
-Signed-off-by: Michael Lange <linuxstuff at milaw.biz>
-Signed-off-by: Alexandre Belloni <alexandre.belloni at free-electrons.com>
----
- drivers/rtc/rtc-ds1307.c | 29 +++++++++++++++++++++++++++--
- 1 file changed, 27 insertions(+), 2 deletions(-)
-
---- a/drivers/rtc/rtc-ds1307.c
-+++ b/drivers/rtc/rtc-ds1307.c
-@@ -860,6 +860,7 @@ static int ds1307_probe(struct i2c_clien
- struct chip_desc *chip = &chips[id->driver_data];
- struct i2c_adapter *adapter = to_i2c_adapter(client->dev.parent);
- bool want_irq = false;
-+ bool ds1307_can_wakeup_device = false;
- unsigned char *buf;
- struct ds1307_platform_data *pdata = dev_get_platdata(&client->dev);
- irq_handler_t irq_handler = ds1307_irq;
-@@ -907,6 +908,20 @@ static int ds1307_probe(struct i2c_clien
- ds1307->write_block_data = ds1307_write_block_data;
- }
-
-+#ifdef CONFIG_OF
-+/*
-+ * For devices with no IRQ directly connected to the SoC, the RTC chip
-+ * can be forced as a wakeup source by stating that explicitly in
-+ * the device's .dts file using the "wakeup-source" boolean property.
-+ * If the "wakeup-source" property is set, don't request an IRQ.
-+ * This will guarantee the 'wakealarm' sysfs entry is available on the device,
-+ * if supported by the RTC.
-+ */
-+ if (of_property_read_bool(client->dev.of_node, "wakeup-source")) {
-+ ds1307_can_wakeup_device = true;
-+ }
-+#endif
-+
- switch (ds1307->type) {
- case ds_1337:
- case ds_1339:
-@@ -925,11 +940,13 @@ static int ds1307_probe(struct i2c_clien
- ds1307->regs[0] &= ~DS1337_BIT_nEOSC;
-
- /*
-- * Using IRQ? Disable the square wave and both alarms.
-+ * Using IRQ or defined as wakeup-source?
-+ * Disable the square wave and both alarms.
- * For some variants, be sure alarms can trigger when we're
- * running on Vbackup (BBSQI/BBSQW)
- */
-- if (ds1307->client->irq > 0 && chip->alarm) {
-+ if (chip->alarm && (ds1307->client->irq > 0 ||
-+ ds1307_can_wakeup_device)) {
- ds1307->regs[0] |= DS1337_BIT_INTCN
- | bbsqi_bitpos[ds1307->type];
- ds1307->regs[0] &= ~(DS1337_BIT_A2IE | DS1337_BIT_A1IE);
-@@ -1144,6 +1161,14 @@ read_rtc:
- return PTR_ERR(ds1307->rtc);
- }
-
-+ if (ds1307_can_wakeup_device) {
-+ /* Disable request for an IRQ */
-+ want_irq = false;
-+ dev_info(&client->dev, "'wakeup-source' is set, request for an IRQ is disabled!\n");
-+ /* We cannot support UIE mode if we do not have an IRQ line */
-+ ds1307->rtc->uie_unsupported = 1;
-+ }
-+
- if (want_irq) {
- err = devm_request_threaded_irq(&client->dev,
- client->irq, NULL, irq_handler,
diff --git a/target/linux/brcm2708/patches-4.4/0138-dt-overlay-add-wittypi-overlay.dts.patch b/target/linux/brcm2708/patches-4.4/0138-dt-overlay-add-wittypi-overlay.dts.patch
deleted file mode 100644
index 1b23afb..0000000
--- a/target/linux/brcm2708/patches-4.4/0138-dt-overlay-add-wittypi-overlay.dts.patch
+++ /dev/null
@@ -1,57 +0,0 @@
-From 1230f669009b1d459873de6b27efd452e55b8746 Mon Sep 17 00:00:00 2001
-From: vitalogy <vitalogy_github at milaw.biz>
-Date: Tue, 19 Jan 2016 07:02:02 +0100
-Subject: [PATCH] dt-overlay: add wittypi-overlay.dts
-
----
- arch/arm/boot/dts/overlays/wittypi-overlay.dts | 44 ++++++++++++++++++++++++++
- 1 file changed, 44 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/wittypi-overlay.dts
-
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/wittypi-overlay.dts
-@@ -0,0 +1,44 @@
-+/*
-+ * Device Tree overlay for Witty Pi extension board by UUGear
-+ *
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&leds>;
-+ __overlay__ {
-+ compatible = "gpio-leds";
-+ wittypi_led: wittypi_led {
-+ label = "wittypi_led";
-+ linux,default-trigger = "default-on";
-+ gpios = <&gpio 17 0>;
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&i2c1>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ rtc: ds1337 at 68 {
-+ compatible = "dallas,ds1337";
-+ reg = <0x68>;
-+ wakeup-source;
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ led_gpio = <&wittypi_led>,"gpios:4";
-+ led_trigger = <&wittypi_led>,"linux,default-trigger";
-+ };
-+
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0139-FIXUP-i2c_bcm2708-Don-t-change-module-baudrate-param.patch b/target/linux/brcm2708/patches-4.4/0139-FIXUP-i2c_bcm2708-Don-t-change-module-baudrate-param.patch
deleted file mode 100644
index 5a37c8c..0000000
--- a/target/linux/brcm2708/patches-4.4/0139-FIXUP-i2c_bcm2708-Don-t-change-module-baudrate-param.patch
+++ /dev/null
@@ -1,98 +0,0 @@
-From 68f3ff91c01ecdd6be1738429f586095427cecd7 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Tue, 19 Jan 2016 16:28:05 +0000
-Subject: [PATCH] FIXUP i2c_bcm2708: Don't change module baudrate parameter
-
-Overwriting the baudrate module parameter creates an apparent
-forced baudrate for i2c busses after the first. Not only does this
-override the baudrate from DT it also prevents the bus ID from
-being initialised.
-
-Also fix whitespace errors.
----
- drivers/i2c/busses/i2c-bcm2708.c | 48 +++++++++++++++++++++-------------------
- 1 file changed, 25 insertions(+), 23 deletions(-)
-
---- a/drivers/i2c/busses/i2c-bcm2708.c
-+++ b/drivers/i2c/busses/i2c-bcm2708.c
-@@ -71,7 +71,6 @@
-
- #define DRV_NAME "bcm2708_i2c"
-
--static unsigned int baudrate_default = CONFIG_I2C_BCM2708_BAUDRATE;
- static unsigned int baudrate;
- module_param(baudrate, uint, S_IRUSR | S_IWUSR | S_IRGRP | S_IWGRP);
- MODULE_PARM_DESC(baudrate, "The I2C baudrate");
-@@ -317,25 +316,28 @@ static int bcm2708_i2c_probe(struct plat
- struct i2c_adapter *adap;
- unsigned long bus_hz;
- u32 cdiv, clk_tout;
--
-- if (!baudrate) {
-- baudrate = baudrate_default;
-- if (pdev->dev.of_node) {
-- u32 bus_clk_rate;
-- pdev->id = of_alias_get_id(pdev->dev.of_node, "i2c");
-- if (pdev->id < 0) {
-- dev_err(&pdev->dev, "alias is missing\n");
-- return -EINVAL;
-- }
-- if (!of_property_read_u32(pdev->dev.of_node,
-- "clock-frequency", &bus_clk_rate))
-- baudrate = bus_clk_rate;
-- else
-- dev_warn(&pdev->dev,
-- "Could not read clock-frequency property\n");
-+ u32 baud;
-+
-+ baud = CONFIG_I2C_BCM2708_BAUDRATE;
-+
-+ if (pdev->dev.of_node) {
-+ u32 bus_clk_rate;
-+ pdev->id = of_alias_get_id(pdev->dev.of_node, "i2c");
-+ if (pdev->id < 0) {
-+ dev_err(&pdev->dev, "alias is missing\n");
-+ return -EINVAL;
- }
-+ if (!of_property_read_u32(pdev->dev.of_node,
-+ "clock-frequency", &bus_clk_rate))
-+ baud = bus_clk_rate;
-+ else
-+ dev_warn(&pdev->dev,
-+ "Could not read clock-frequency property\n");
- }
-
-+ if (baudrate)
-+ baud = baudrate;
-+
- regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (!regs) {
- dev_err(&pdev->dev, "could not get IO memory\n");
-@@ -419,21 +421,21 @@ static int bcm2708_i2c_probe(struct plat
- }
-
- bus_hz = clk_get_rate(bi->clk);
-- cdiv = bus_hz / baudrate;
-+ cdiv = bus_hz / baud;
- if (cdiv > 0xffff) {
- cdiv = 0xffff;
-- baudrate = bus_hz / cdiv;
-+ baud = bus_hz / cdiv;
- }
--
-- clk_tout = 35/1000*baudrate; //35ms timeout as per SMBus specs.
-- if (clk_tout > 0xffff)
-+
-+ clk_tout = 35/1000*baud; //35ms timeout as per SMBus specs.
-+ if (clk_tout > 0xffff)
- clk_tout = 0xffff;
-
- bi->cdiv = cdiv;
- bi->clk_tout = clk_tout;
-
- dev_info(&pdev->dev, "BSC%d Controller at 0x%08lx (irq %d) (baudrate %d)\n",
-- pdev->id, (unsigned long)regs->start, irq, baudrate);
-+ pdev->id, (unsigned long)regs->start, irq, baud);
-
- return 0;
-
diff --git a/target/linux/brcm2708/patches-4.4/0140-Allow-up-to-24dB-digital-gain-to-be-applied-when-usi.patch b/target/linux/brcm2708/patches-4.4/0140-Allow-up-to-24dB-digital-gain-to-be-applied-when-usi.patch
deleted file mode 100644
index bb4f692..0000000
--- a/target/linux/brcm2708/patches-4.4/0140-Allow-up-to-24dB-digital-gain-to-be-applied-when-usi.patch
+++ /dev/null
@@ -1,99 +0,0 @@
-From fb80a497382f9c693ad78524fb0c17454bd9b7f4 Mon Sep 17 00:00:00 2001
-From: Digital Dreamtime <clive.messer at digitaldreamtime.co.uk>
-Date: Thu, 4 Feb 2016 14:14:44 +0000
-Subject: [PATCH] Allow up to 24dB digital gain to be applied when using
- IQAudIO DAC+
-
-24db_digital_gain DT param can be used to specify that PCM512x
-codec "Digital" volume control should not be limited to 0dB gain,
-and if specified will allow the full 24dB gain.
----
- arch/arm/boot/dts/overlays/README | 17 +++++++++++++++--
- .../boot/dts/overlays/iqaudio-dacplus-overlay.dts | 6 +++++-
- sound/soc/bcm/iqaudio-dac.c | 20 ++++++++++++++------
- 3 files changed, 34 insertions(+), 9 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -362,8 +362,21 @@ Params: <None>
-
- Name: iqaudio-dacplus
- Info: Configures the IQaudio DAC+ audio card
--Load: dtoverlay=iqaudio-dacplus
--Params: <None>
-+Load: dtoverlay=iqaudio-dacplus,<param>=<val>
-+Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec
-+ Digital volume control. Enable with
-+ "dtoverlay=iqaudio-dacplus,24db_digital_gain"
-+ (The default behaviour is that the Digital
-+ volume control is limited to a maximum of
-+ 0dB. ie. it can attenuate but not provide
-+ gain. For most users, this will be desired
-+ as it will prevent clipping. By appending
-+ the 24db_digital_gain parameter, the Digital
-+ volume control will allow up to 24dB of
-+ gain. If this parameter is enabled, it is the
-+ responsibility of the user to ensure that
-+ the Digital volume control is set to a value
-+ that does not result in clipping/distortion!)
-
-
- Name: lirc-rpi
---- a/arch/arm/boot/dts/overlays/iqaudio-dacplus-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/iqaudio-dacplus-overlay.dts
-@@ -7,7 +7,7 @@
-
- fragment at 0 {
- target = <&sound>;
-- __overlay__ {
-+ frag0: __overlay__ {
- compatible = "iqaudio,iqaudio-dac";
- i2s-controller = <&i2s>;
- status = "okay";
-@@ -36,4 +36,8 @@
- };
- };
- };
-+
-+ __overrides__ {
-+ 24db_digital_gain = <&frag0>,"iqaudio,24db_digital_gain?";
-+ };
- };
---- a/sound/soc/bcm/iqaudio-dac.c
-+++ b/sound/soc/bcm/iqaudio-dac.c
-@@ -23,14 +23,19 @@
- #include <sound/soc.h>
- #include <sound/jack.h>
-
-+static bool digital_gain_0db_limit = true;
-+
- static int snd_rpi_iqaudio_dac_init(struct snd_soc_pcm_runtime *rtd)
- {
-- int ret;
-- struct snd_soc_card *card = rtd->card;
--
-- ret = snd_soc_limit_volume(card, "Digital Playback Volume", 207);
-- if (ret < 0)
-- dev_warn(card->dev, "Failed to set volume limit: %d\n", ret);
-+ if (digital_gain_0db_limit)
-+ {
-+ int ret;
-+ struct snd_soc_card *card = rtd->card;
-+
-+ ret = snd_soc_limit_volume(card, "Digital Playback Volume", 207);
-+ if (ret < 0)
-+ dev_warn(card->dev, "Failed to set volume limit: %d\n", ret);
-+ }
-
- return 0;
- }
-@@ -94,6 +99,9 @@ static int snd_rpi_iqaudio_dac_probe(str
- dai->platform_name = NULL;
- dai->platform_of_node = i2s_node;
- }
-+
-+ digital_gain_0db_limit = !of_property_read_bool(pdev->dev.of_node,
-+ "iqaudio,24db_digital_gain");
- }
-
- ret = snd_soc_register_card(&snd_rpi_iqaudio_dac);
diff --git a/target/linux/brcm2708/patches-4.4/0141-Limit-PCM512x-Digital-gain-to-0dB-by-default-with-Hi.patch b/target/linux/brcm2708/patches-4.4/0141-Limit-PCM512x-Digital-gain-to-0dB-by-default-with-Hi.patch
deleted file mode 100644
index 4f63921..0000000
--- a/target/linux/brcm2708/patches-4.4/0141-Limit-PCM512x-Digital-gain-to-0dB-by-default-with-Hi.patch
+++ /dev/null
@@ -1,98 +0,0 @@
-From 98357bafa929284bbd1046556971c3d4ae9f71d9 Mon Sep 17 00:00:00 2001
-From: Digital Dreamtime <clive.messer at digitaldreamtime.co.uk>
-Date: Thu, 4 Feb 2016 20:04:00 +0000
-Subject: [PATCH] Limit PCM512x "Digital" gain to 0dB by default with HiFiBerry
- DAC+
-
-24db_digital_gain DT param can be used to specify that PCM512x
-codec "Digital" volume control should not be limited to 0dB gain,
-and if specified will allow the full 24dB gain.
----
- arch/arm/boot/dts/overlays/README | 17 +++++++++++++++--
- .../arm/boot/dts/overlays/hifiberry-dacplus-overlay.dts | 6 +++++-
- sound/soc/bcm/hifiberry_dacplus.c | 14 ++++++++++++++
- 3 files changed, 34 insertions(+), 3 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -273,8 +273,21 @@ Params: <None>
-
- Name: hifiberry-dacplus
- Info: Configures the HifiBerry DAC+ audio card
--Load: dtoverlay=hifiberry-dacplus
--Params: <None>
-+Load: dtoverlay=hifiberry-dacplus,<param>=<val>
-+Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec
-+ Digital volume control. Enable with
-+ "dtoverlay=hifiberry-dacplus,24db_digital_gain"
-+ (The default behaviour is that the Digital
-+ volume control is limited to a maximum of
-+ 0dB. ie. it can attenuate but not provide
-+ gain. For most users, this will be desired
-+ as it will prevent clipping. By appending
-+ the 24dB_digital_gain parameter, the Digital
-+ volume control will allow up to 24dB of
-+ gain. If this parameter is enabled, it is the
-+ responsibility of the user to ensure that
-+ the Digital volume control is set to a value
-+ that does not result in clipping/distortion!)
-
-
- Name: hifiberry-digi
---- a/arch/arm/boot/dts/overlays/hifiberry-dacplus-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/hifiberry-dacplus-overlay.dts
-@@ -17,7 +17,7 @@
-
- fragment at 1 {
- target = <&sound>;
-- __overlay__ {
-+ frag1: __overlay__ {
- compatible = "hifiberry,hifiberry-dacplus";
- i2s-controller = <&i2s>;
- status = "okay";
-@@ -47,4 +47,8 @@
- };
- };
- };
-+
-+ __overrides__ {
-+ 24db_digital_gain = <&frag1>,"hifiberry,24db_digital_gain?";
-+ };
- };
---- a/sound/soc/bcm/hifiberry_dacplus.c
-+++ b/sound/soc/bcm/hifiberry_dacplus.c
-@@ -48,6 +48,7 @@ struct pcm512x_priv {
- #define CLK_48EN_RATE 24576000UL
-
- static bool snd_rpi_hifiberry_is_dacpro;
-+static bool digital_gain_0db_limit = true;
-
- static void snd_rpi_hifiberry_dacplus_select_clk(struct snd_soc_codec *codec,
- int clk_id)
-@@ -167,6 +168,16 @@ static int snd_rpi_hifiberry_dacplus_ini
- snd_soc_update_bits(codec, PCM512x_GPIO_OUTPUT_4, 0x0f, 0x02);
- snd_soc_update_bits(codec, PCM512x_GPIO_CONTROL_1, 0x08, 0x08);
-
-+ if (digital_gain_0db_limit)
-+ {
-+ int ret;
-+ struct snd_soc_card *card = rtd->card;
-+
-+ ret = snd_soc_limit_volume(card, "Digital Playback Volume", 207);
-+ if (ret < 0)
-+ dev_warn(card->dev, "Failed to set volume limit: %d\n", ret);
-+ }
-+
- return 0;
- }
-
-@@ -299,6 +310,9 @@ static int snd_rpi_hifiberry_dacplus_pro
- dai->platform_name = NULL;
- dai->platform_of_node = i2s_node;
- }
-+
-+ digital_gain_0db_limit = !of_property_read_bool(
-+ pdev->dev.of_node, "hifiberry,24db_digital_gain");
- }
-
- ret = snd_soc_register_card(&snd_rpi_hifiberry_dacplus);
diff --git a/target/linux/brcm2708/patches-4.4/0142-BCM270X_DT-Adjust-overlay-README-formatting.patch b/target/linux/brcm2708/patches-4.4/0142-BCM270X_DT-Adjust-overlay-README-formatting.patch
deleted file mode 100644
index c66eb6d..0000000
--- a/target/linux/brcm2708/patches-4.4/0142-BCM270X_DT-Adjust-overlay-README-formatting.patch
+++ /dev/null
@@ -1,729 +0,0 @@
-From 0feb25cf50f89502ea7f2150f0fab1f9d40b138a Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 8 Feb 2016 09:46:33 +0000
-Subject: [PATCH] BCM270X_DT: Adjust overlay README formatting
-
----
- arch/arm/boot/dts/overlays/README | 414 +++++++++++++++++++-------------------
- 1 file changed, 207 insertions(+), 207 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -83,58 +83,58 @@ Name: <The base DTB>
- Info: Configures the base Raspberry Pi hardware
- Load: <loaded automatically>
- Params:
-- audio Set to "on" to enable the onboard ALSA audio
-- interface (default "off")
-+ audio Set to "on" to enable the onboard ALSA audio
-+ interface (default "off")
-
-- i2c_arm Set to "on" to enable the ARM's i2c interface
-- (default "off")
-+ i2c_arm Set to "on" to enable the ARM's i2c interface
-+ (default "off")
-
-- i2c_vc Set to "on" to enable the i2c interface
-- usually reserved for the VideoCore processor
-- (default "off")
-+ i2c_vc Set to "on" to enable the i2c interface
-+ usually reserved for the VideoCore processor
-+ (default "off")
-
-- i2c An alias for i2c_arm
-+ i2c An alias for i2c_arm
-
-- i2c_arm_baudrate Set the baudrate of the ARM's i2c interface
-- (default "100000")
-+ i2c_arm_baudrate Set the baudrate of the ARM's i2c interface
-+ (default "100000")
-
-- i2c_vc_baudrate Set the baudrate of the VideoCore i2c interface
-- (default "100000")
-+ i2c_vc_baudrate Set the baudrate of the VideoCore i2c interface
-+ (default "100000")
-
-- i2c_baudrate An alias for i2c_arm_baudrate
-+ i2c_baudrate An alias for i2c_arm_baudrate
-
-- i2s Set to "on" to enable the i2s interface
-- (default "off")
-+ i2s Set to "on" to enable the i2s interface
-+ (default "off")
-
-- spi Set to "on" to enable the spi interfaces
-- (default "off")
-+ spi Set to "on" to enable the spi interfaces
-+ (default "off")
-
-- random Set to "on" to enable the hardware random
-- number generator (default "on")
-+ random Set to "on" to enable the hardware random
-+ number generator (default "on")
-
-- uart0 Set to "off" to disable uart0 (default "on")
-+ uart0 Set to "off" to disable uart0 (default "on")
-
-- watchdog Set to "on" to enable the hardware watchdog
-- (default "off")
-+ watchdog Set to "on" to enable the hardware watchdog
-+ (default "off")
-
-- act_led_trigger Choose which activity the LED tracks.
-- Use "heartbeat" for a nice load indicator.
-- (default "mmc")
-+ act_led_trigger Choose which activity the LED tracks.
-+ Use "heartbeat" for a nice load indicator.
-+ (default "mmc")
-
-- act_led_activelow Set to "on" to invert the sense of the LED
-- (default "off")
-+ act_led_activelow Set to "on" to invert the sense of the LED
-+ (default "off")
-
-- act_led_gpio Set which GPIO to use for the activity LED
-- (in case you want to connect it to an external
-- device)
-- (default "16" on a non-Plus board, "47" on a
-- Plus or Pi 2)
-+ act_led_gpio Set which GPIO to use for the activity LED
-+ (in case you want to connect it to an external
-+ device)
-+ (default "16" on a non-Plus board, "47" on a
-+ Plus or Pi 2)
-
- pwr_led_trigger
- pwr_led_activelow
- pwr_led_gpio
-- As for act_led_*, but using the PWR LED.
-- Not available on Model A/B boards.
-+ As for act_led_*, but using the PWR LED.
-+ Not available on Model A/B boards.
-
- N.B. It is recommended to only enable those interfaces that are needed.
- Leaving all interfaces enabled can lead to unwanted behaviour (i2c_vc
-@@ -149,19 +149,19 @@ Params:
- Name: ads7846
- Info: ADS7846 Touch controller
- Load: dtoverlay=ads7846,<param>=<val>
--Params: cs SPI bus Chip Select (default 1)
-- speed SPI bus speed (default 2MHz, max 3.25MHz)
-- penirq GPIO used for PENIRQ. REQUIRED
-- penirq_pull Set GPIO pull (default 0=none, 2=pullup)
-- swapxy Swap x and y axis
-- xmin Minimum value on the X axis (default 0)
-- ymin Minimum value on the Y axis (default 0)
-- xmax Maximum value on the X axis (default 4095)
-- ymax Maximum value on the Y axis (default 4095)
-- pmin Minimum reported pressure value (default 0)
-- pmax Maximum reported pressure value (default 65535)
-- xohms Touchpanel sensitivity (X-plate resistance)
-- (default 400)
-+Params: cs SPI bus Chip Select (default 1)
-+ speed SPI bus speed (default 2MHz, max 3.25MHz)
-+ penirq GPIO used for PENIRQ. REQUIRED
-+ penirq_pull Set GPIO pull (default 0=none, 2=pullup)
-+ swapxy Swap x and y axis
-+ xmin Minimum value on the X axis (default 0)
-+ ymin Minimum value on the Y axis (default 0)
-+ xmax Maximum value on the X axis (default 4095)
-+ ymax Maximum value on the Y axis (default 4095)
-+ pmin Minimum reported pressure value (default 0)
-+ pmax Maximum reported pressure value (default 65535)
-+ xohms Touchpanel sensitivity (X-plate resistance)
-+ (default 400)
-
- penirq is required and usually xohms (60-100) has to be set as well.
- Apart from that, pmax (255) and swapxy are also common.
-@@ -175,12 +175,12 @@ Name: at86rf233
- Info: Configures the Atmel AT86RF233 802.15.4 low-power WPAN transceiver,
- connected to spi0.0
- Load: dtoverlay=at86rf233,<param>=<val>
--Params: interrupt GPIO used for INT (default 23)
-- reset GPIO used for Reset (default 24)
-- sleep GPIO used for Sleep (default 25)
-- speed SPI bus speed in Hz (default 6000000)
-- trim Fine tuning of the internal capacitance
-- arrays (0=+0pF, 15=+4.5pF, default 15)
-+Params: interrupt GPIO used for INT (default 23)
-+ reset GPIO used for Reset (default 24)
-+ sleep GPIO used for Sleep (default 25)
-+ speed SPI bus speed in Hz (default 6000000)
-+ trim Fine tuning of the internal capacitance
-+ arrays (0=+0pF, 15=+4.5pF, default 15)
-
-
- Name: bmp085_i2c-sensor
-@@ -194,8 +194,8 @@ Name: dht11
- Info: Overlay for the DHT11/DHT21/DHT22 humidity/temperature sensors
- Also sometimes found with the part number(s) AM230x.
- Load: dtoverlay=dht11,<param>=<val>
--Params: gpiopin GPIO connected to the sensor's DATA output.
-- (default 4)
-+Params: gpiopin GPIO connected to the sensor's DATA output.
-+ (default 4)
-
-
- Name: dwc-otg
-@@ -208,15 +208,15 @@ Params: <None>
- Name: dwc2
- Info: Selects the dwc2 USB controller driver
- Load: dtoverlay=dwc2,<param>=<val>
--Params: dr_mode Dual role mode: "host", "peripheral" or "otg"
-+Params: dr_mode Dual role mode: "host", "peripheral" or "otg"
-
-- g-rx-fifo-size Size of rx fifo size in gadget mode
-+ g-rx-fifo-size Size of rx fifo size in gadget mode
-
-- g-np-tx-fifo-size Size of non-periodic tx fifo size in gadget
-- mode
-+ g-np-tx-fifo-size Size of non-periodic tx fifo size in gadget
-+ mode
-
-- g-tx-fifo-size Size of periodic tx fifo per endpoint
-- (except ep0) in gadget mode
-+ g-tx-fifo-size Size of periodic tx fifo per endpoint
-+ (except ep0) in gadget mode
-
-
- [ The ds1307-rtc overlay has been deleted. See i2c-rtc. ]
-@@ -225,9 +225,9 @@ Params: dr_mode Dual ro
- Name: enc28j60
- Info: Overlay for the Microchip ENC28J60 Ethernet Controller (SPI)
- Load: dtoverlay=enc28j60,<param>=<val>
--Params: int_pin GPIO used for INT (default 25)
-+Params: int_pin GPIO used for INT (default 25)
-
-- speed SPI bus speed (default 12000000)
-+ speed SPI bus speed (default 12000000)
-
-
- Name: gpio-ir
-@@ -237,26 +237,26 @@ Info: Use GPIO pin as rc-core style in
- not required! The key mapping and other decoding parameters can be
- configured by "ir-keytable" tool.
- Load: dtoverlay=gpio-ir,<param>=<val>
--Params: gpio_pin Input pin number. Default is 18.
-+Params: gpio_pin Input pin number. Default is 18.
-
-- gpio_pull Desired pull-up/down state (off, down, up)
-- Default is "down".
-+ gpio_pull Desired pull-up/down state (off, down, up)
-+ Default is "down".
-
-- rc-map-name Default rc keymap (can also be changed by
-- ir-keytable), defaults to "rc-rc6-mce"
-+ rc-map-name Default rc keymap (can also be changed by
-+ ir-keytable), defaults to "rc-rc6-mce"
-
-
- Name: gpio-poweroff
- Info: Drives a GPIO high or low on reboot
- Load: dtoverlay=gpio-poweroff,<param>=<val>
--Params: gpiopin GPIO for signalling (default 26)
-+Params: gpiopin GPIO for signalling (default 26)
-
-- active_low Set if the power control device requires a
-- high->low transition to trigger a power-down.
-- Note that this will require the support of a
-- custom dt-blob.bin to prevent a power-down
-- during the boot process, and that a reboot
-- will also cause the pin to go low.
-+ active_low Set if the power control device requires a
-+ high->low transition to trigger a power-down.
-+ Note that this will require the support of a
-+ custom dt-blob.bin to prevent a power-down
-+ during the boot process, and that a reboot
-+ will also cause the pin to go low.
-
-
- Name: hifiberry-amp
-@@ -300,65 +300,65 @@ Name: hy28a
- Info: HY28A - 2.8" TFT LCD Display Module by HAOYU Electronics
- Default values match Texy's display shield
- Load: dtoverlay=hy28a,<param>=<val>
--Params: speed Display SPI bus speed
-+Params: speed Display SPI bus speed
-
-- rotate Display rotation {0,90,180,270}
-+ rotate Display rotation {0,90,180,270}
-
-- fps Delay between frame updates
-+ fps Delay between frame updates
-
-- debug Debug output level {0-7}
-+ debug Debug output level {0-7}
-
-- xohms Touchpanel sensitivity (X-plate resistance)
-+ xohms Touchpanel sensitivity (X-plate resistance)
-
-- resetgpio GPIO used to reset controller
-+ resetgpio GPIO used to reset controller
-
-- ledgpio GPIO used to control backlight
-+ ledgpio GPIO used to control backlight
-
-
- Name: hy28b
- Info: HY28B - 2.8" TFT LCD Display Module by HAOYU Electronics
- Default values match Texy's display shield
- Load: dtoverlay=hy28b,<param>=<val>
--Params: speed Display SPI bus speed
-+Params: speed Display SPI bus speed
-
-- rotate Display rotation {0,90,180,270}
-+ rotate Display rotation {0,90,180,270}
-
-- fps Delay between frame updates
-+ fps Delay between frame updates
-
-- debug Debug output level {0-7}
-+ debug Debug output level {0-7}
-
-- xohms Touchpanel sensitivity (X-plate resistance)
-+ xohms Touchpanel sensitivity (X-plate resistance)
-
-- resetgpio GPIO used to reset controller
-+ resetgpio GPIO used to reset controller
-
-- ledgpio GPIO used to control backlight
-+ ledgpio GPIO used to control backlight
-
-
- Name: i2c-gpio
- Info: Adds support for software i2c controller on gpio pins
- Load: dtoverlay=i2c-gpio,<param>=<val>
--Params: i2c_gpio_sda GPIO used for I2C data (default "23")
-+Params: i2c_gpio_sda GPIO used for I2C data (default "23")
-
-- i2c_gpio_scl GPIO used for I2C clock (default "24")
-+ i2c_gpio_scl GPIO used for I2C clock (default "24")
-
-- i2c_gpio_delay_us Clock delay in microseconds
-- (default "2" = ~100kHz)
-+ i2c_gpio_delay_us Clock delay in microseconds
-+ (default "2" = ~100kHz)
-
-
- Name: i2c-rtc
- Info: Adds support for a number of I2C Real Time Clock devices
- Load: dtoverlay=i2c-rtc,<param>=<val>
--Params: ds1307 Select the DS1307 device
-+Params: ds1307 Select the DS1307 device
-
-- ds3231 Select the DS3231 device
-+ ds3231 Select the DS3231 device
-
-- mcp7941x Select the MCP7941x device
-+ mcp7941x Select the MCP7941x device
-
-- pcf2127 Select the PCF2127 device
-+ pcf2127 Select the PCF2127 device
-
-- pcf8523 Select the PCF8523 device
-+ pcf8523 Select the PCF8523 device
-
-- pcf8563 Select the PCF8563 device
-+ pcf8563 Select the PCF8563 device
-
-
- Name: i2s-mmap
-@@ -396,70 +396,70 @@ Name: lirc-rpi
- Info: Configures lirc-rpi (Linux Infrared Remote Control for Raspberry Pi)
- Consult the module documentation for more details.
- Load: dtoverlay=lirc-rpi,<param>=<val>
--Params: gpio_out_pin GPIO for output (default "17")
-+Params: gpio_out_pin GPIO for output (default "17")
-
-- gpio_in_pin GPIO for input (default "18")
-+ gpio_in_pin GPIO for input (default "18")
-
-- gpio_in_pull Pull up/down/off on the input pin
-- (default "down")
-+ gpio_in_pull Pull up/down/off on the input pin
-+ (default "down")
-
-- sense Override the IR receive auto-detection logic:
-- "0" = force active-high
-- "1" = force active-low
-- "-1" = use auto-detection
-- (default "-1")
-+ sense Override the IR receive auto-detection logic:
-+ "0" = force active-high
-+ "1" = force active-low
-+ "-1" = use auto-detection
-+ (default "-1")
-
-- softcarrier Turn the software carrier "on" or "off"
-- (default "on")
-+ softcarrier Turn the software carrier "on" or "off"
-+ (default "on")
-
-- invert "on" = invert the output pin (default "off")
-+ invert "on" = invert the output pin (default "off")
-
-- debug "on" = enable additional debug messages
-- (default "off")
-+ debug "on" = enable additional debug messages
-+ (default "off")
-
-
- Name: mcp2515-can0
- Info: Configures the MCP2515 CAN controller on spi0.0
- Load: dtoverlay=mcp2515-can0,<param>=<val>
--Params: oscillator Clock frequency for the CAN controller (Hz)
-+Params: oscillator Clock frequency for the CAN controller (Hz)
-
-- spimaxfrequency Maximum SPI frequence (Hz)
-+ spimaxfrequency Maximum SPI frequence (Hz)
-
-- interrupt GPIO for interrupt signal
-+ interrupt GPIO for interrupt signal
-
-
- Name: mcp2515-can1
- Info: Configures the MCP2515 CAN controller on spi0.1
- Load: dtoverlay=mcp2515-can1,<param>=<val>
--Params: oscillator Clock frequency for the CAN controller (Hz)
-+Params: oscillator Clock frequency for the CAN controller (Hz)
-
-- spimaxfrequency Maximum SPI frequence (Hz)
-+ spimaxfrequency Maximum SPI frequence (Hz)
-
-- interrupt GPIO for interrupt signal
-+ interrupt GPIO for interrupt signal
-
-
- Name: mmc
- Info: Selects the bcm2835-mmc SD/MMC driver, optionally with overclock
- Load: dtoverlay=mmc,<param>=<val>
--Params: overclock_50 Clock (in MHz) to use when the MMC framework
-- requests 50MHz
-- force_pio Disable DMA support
-+Params: overclock_50 Clock (in MHz) to use when the MMC framework
-+ requests 50MHz
-+ force_pio Disable DMA support
-
-
- Name: mz61581
- Info: MZ61581 display by Tontec
- Load: dtoverlay=mz61581,<param>=<val>
--Params: speed Display SPI bus speed
-+Params: speed Display SPI bus speed
-
-- rotate Display rotation {0,90,180,270}
-+ rotate Display rotation {0,90,180,270}
-
-- fps Delay between frame updates
-+ fps Delay between frame updates
-
-- txbuflen Transmit buffer length (default 32768)
-+ txbuflen Transmit buffer length (default 32768)
-
-- debug Debug output level {0-7}
-+ debug Debug output level {0-7}
-
-- xohms Touchpanel sensitivity (X-plate resistance)
-+ xohms Touchpanel sensitivity (X-plate resistance)
-
-
- [ The pcf2127-rtc overlay has been deleted. See i2c-rtc. ]
-@@ -474,69 +474,69 @@ Params: speed Display
- Name: piscreen
- Info: PiScreen display by OzzMaker.com
- Load: dtoverlay=piscreen,<param>=<val>
--Params: speed Display SPI bus speed
-+Params: speed Display SPI bus speed
-
-- rotate Display rotation {0,90,180,270}
-+ rotate Display rotation {0,90,180,270}
-
-- fps Delay between frame updates
-+ fps Delay between frame updates
-
-- debug Debug output level {0-7}
-+ debug Debug output level {0-7}
-
-- xohms Touchpanel sensitivity (X-plate resistance)
-+ xohms Touchpanel sensitivity (X-plate resistance)
-
-
- Name: piscreen2r
- Info: PiScreen 2 with resistive TP display by OzzMaker.com
- Load: dtoverlay=piscreen2r,<param>=<val>
--Params: speed Display SPI bus speed
-+Params: speed Display SPI bus speed
-
-- rotate Display rotation {0,90,180,270}
-+ rotate Display rotation {0,90,180,270}
-
-- fps Delay between frame updates
-+ fps Delay between frame updates
-
-- debug Debug output level {0-7}
-+ debug Debug output level {0-7}
-
-- xohms Touchpanel sensitivity (X-plate resistance)
-+ xohms Touchpanel sensitivity (X-plate resistance)
-
-
- Name: pitft28-capacitive
- Info: Adafruit PiTFT 2.8" capacitive touch screen
- Load: dtoverlay=pitft28-capacitive,<param>=<val>
--Params: speed Display SPI bus speed
-+Params: speed Display SPI bus speed
-
-- rotate Display rotation {0,90,180,270}
-+ rotate Display rotation {0,90,180,270}
-
-- fps Delay between frame updates
-+ fps Delay between frame updates
-
-- debug Debug output level {0-7}
-+ debug Debug output level {0-7}
-
-- touch-sizex Touchscreen size x (default 240)
-+ touch-sizex Touchscreen size x (default 240)
-
-- touch-sizey Touchscreen size y (default 320)
-+ touch-sizey Touchscreen size y (default 320)
-
-- touch-invx Touchscreen inverted x axis
-+ touch-invx Touchscreen inverted x axis
-
-- touch-invy Touchscreen inverted y axis
-+ touch-invy Touchscreen inverted y axis
-
-- touch-swapxy Touchscreen swapped x y axis
-+ touch-swapxy Touchscreen swapped x y axis
-
-
- Name: pitft28-resistive
- Info: Adafruit PiTFT 2.8" resistive touch screen
- Load: dtoverlay=pitft28-resistive,<param>=<val>
--Params: speed Display SPI bus speed
-+Params: speed Display SPI bus speed
-
-- rotate Display rotation {0,90,180,270}
-+ rotate Display rotation {0,90,180,270}
-
-- fps Delay between frame updates
-+ fps Delay between frame updates
-
-- debug Debug output level {0-7}
-+ debug Debug output level {0-7}
-
-
- Name: pps-gpio
- Info: Configures the pps-gpio (pulse-per-second time signal via GPIO).
- Load: dtoverlay=pps-gpio,<param>=<val>
--Params: gpiopin Input GPIO (default "18")
-+Params: gpiopin Input GPIO (default "18")
-
-
- Name: pwm
-@@ -553,9 +553,9 @@ Info: Configures a single PWM channel
- 4) Currently the clock must have been enabled and configured
- by other means.
- Load: dtoverlay=pwm,<param>=<val>
--Params: pin Output pin (default 18) - see table
-- func Pin function (default 2 = Alt5) - see above
-- clock PWM clock frequency (informational)
-+Params: pin Output pin (default 18) - see table
-+ func Pin function (default 2 = Alt5) - see above
-+ clock PWM clock frequency (informational)
-
-
- Name: pwm-2chan
-@@ -572,11 +572,11 @@ Info: Configures both PWM channels
- 4) Currently the clock must have been enabled and configured
- by other means.
- Load: dtoverlay=pwm-2chan,<param>=<val>
--Params: pin Output pin (default 18) - see table
-- pin2 Output pin for other channel (default 19)
-- func Pin function (default 2 = Alt5) - see above
-- func2 Function for pin2 (default 2 = Alt5)
-- clock PWM clock frequency (informational)
-+Params: pin Output pin (default 18) - see table
-+ pin2 Output pin for other channel (default 19)
-+ func Pin function (default 2 = Alt5) - see above
-+ func2 Function for pin2 (default 2 = Alt5)
-+ clock PWM clock frequency (informational)
-
-
- Name: raspidac3
-@@ -600,15 +600,15 @@ Params: <None>
- Name: rpi-display
- Info: RPi-Display - 2.8" Touch Display by Watterott
- Load: dtoverlay=rpi-display,<param>=<val>
--Params: speed Display SPI bus speed
-+Params: speed Display SPI bus speed
-
-- rotate Display rotation {0,90,180,270}
-+ rotate Display rotation {0,90,180,270}
-
-- fps Delay between frame updates
-+ fps Delay between frame updates
-
-- debug Debug output level {0-7}
-+ debug Debug output level {0-7}
-
-- xohms Touchpanel sensitivity (X-plate resistance)
-+ xohms Touchpanel sensitivity (X-plate resistance)
-
-
- Name: rpi-ft5406
-@@ -632,52 +632,52 @@ Params: <None>
- Name: sdhost
- Info: Selects the bcm2835-sdhost SD/MMC driver, optionally with overclock
- Load: dtoverlay=sdhost,<param>=<val>
--Params: overclock_50 Clock (in MHz) to use when the MMC framework
-- requests 50MHz
-+Params: overclock_50 Clock (in MHz) to use when the MMC framework
-+ requests 50MHz
-
-- force_pio Disable DMA support (default off)
-+ force_pio Disable DMA support (default off)
-
-- pio_limit Number of blocks above which to use DMA
-- (default 1)
-+ pio_limit Number of blocks above which to use DMA
-+ (default 1)
-
-- debug Enable debug output (default off)
-+ debug Enable debug output (default off)
-
-
- Name: sdio
- Info: Selects the bcm2835-sdhost SD/MMC driver, optionally with overclock,
- and enables SDIO via GPIOs 22-27.
- Load: dtoverlay=sdio,<param>=<val>
--Params: overclock_50 SD Clock (in MHz) to use when the MMC framework
-- requests 50MHz
-+Params: overclock_50 SD Clock (in MHz) to use when the MMC framework
-+ requests 50MHz
-
-- sdio_overclock SDIO Clock (in MHz) to use when the MMC
-- framework requests 50MHz
-+ sdio_overclock SDIO Clock (in MHz) to use when the MMC
-+ framework requests 50MHz
-
-- force_pio Disable DMA support (default off)
-+ force_pio Disable DMA support (default off)
-
-- pio_limit Number of blocks above which to use DMA
-- (default 1)
-+ pio_limit Number of blocks above which to use DMA
-+ (default 1)
-
-- debug Enable debug output (default off)
-+ debug Enable debug output (default off)
-
-- poll_once Disable SDIO-device polling every second
-- (default on: polling once at boot-time)
-+ poll_once Disable SDIO-device polling every second
-+ (default on: polling once at boot-time)
-
-- bus_width Set the SDIO host bus width (default 4 bits)
-+ bus_width Set the SDIO host bus width (default 4 bits)
-
-
- Name: sdtweak
- Info: Tunes the bcm2835-sdhost SD/MMC driver
- Load: dtoverlay=sdtweak,<param>=<val>
--Params: overclock_50 Clock (in MHz) to use when the MMC framework
-- requests 50MHz
-+Params: overclock_50 Clock (in MHz) to use when the MMC framework
-+ requests 50MHz
-
-- force_pio Disable DMA support (default off)
-+ force_pio Disable DMA support (default off)
-
-- pio_limit Number of blocks above which to use DMA
-- (default 1)
-+ pio_limit Number of blocks above which to use DMA
-+ (default 1)
-
-- debug Enable debug output (default off)
-+ debug Enable debug output (default off)
-
-
- Name: smi
-@@ -708,25 +708,25 @@ Name: tinylcd35
- Info: 3.5" Color TFT Display by www.tinylcd.com
- Options: Touch, RTC, keypad
- Load: dtoverlay=tinylcd35,<param>=<val>
--Params: speed Display SPI bus speed
-+Params: speed Display SPI bus speed
-
-- rotate Display rotation {0,90,180,270}
-+ rotate Display rotation {0,90,180,270}
-
-- fps Delay between frame updates
-+ fps Delay between frame updates
-
-- debug Debug output level {0-7}
-+ debug Debug output level {0-7}
-
-- touch Enable touch panel
-+ touch Enable touch panel
-
-- touchgpio Touch controller IRQ GPIO
-+ touchgpio Touch controller IRQ GPIO
-
-- xohms Touchpanel: Resistance of X-plate in ohms
-+ xohms Touchpanel: Resistance of X-plate in ohms
-
-- rtc-pcf PCF8563 Real Time Clock
-+ rtc-pcf PCF8563 Real Time Clock
-
-- rtc-ds DS1307 Real Time Clock
-+ rtc-ds DS1307 Real Time Clock
-
-- keypad Enable keypad
-+ keypad Enable keypad
-
- Examples:
- Display with touchpanel, PCF8563 RTC and keypad:
-@@ -738,9 +738,9 @@ Params: speed Display
- Name: uart1
- Info: Enable uart1 in place of uart0
- Load: dtoverlay=uart1,<param>=<val>
--Params: txd1_pin GPIO pin for TXD1 (14, 32 or 40 - default 14)
-+Params: txd1_pin GPIO pin for TXD1 (14, 32 or 40 - default 14)
-
-- rxd1_pin GPIO pin for RXD1 (15, 33 or 41 - default 15)
-+ rxd1_pin GPIO pin for RXD1 (15, 33 or 41 - default 15)
-
-
- Name: vc4-kms-v3d
-@@ -763,22 +763,22 @@ Name: w1-gpio
- Info: Configures the w1-gpio Onewire interface module.
- Use this overlay if you *don't* need a GPIO to drive an external pullup.
- Load: dtoverlay=w1-gpio,<param>=<val>
--Params: gpiopin GPIO for I/O (default "4")
-+Params: gpiopin GPIO for I/O (default "4")
-
-- pullup Non-zero, "on", or "y" to enable the parasitic
-- power (2-wire, power-on-data) feature
-+ pullup Non-zero, "on", or "y" to enable the parasitic
-+ power (2-wire, power-on-data) feature
-
-
- Name: w1-gpio-pullup
- Info: Configures the w1-gpio Onewire interface module.
- Use this overlay if you *do* need a GPIO to drive an external pullup.
- Load: dtoverlay=w1-gpio-pullup,<param>=<val>
--Params: gpiopin GPIO for I/O (default "4")
-+Params: gpiopin GPIO for I/O (default "4")
-
-- pullup Non-zero, "on", or "y" to enable the parasitic
-- power (2-wire, power-on-data) feature
-+ pullup Non-zero, "on", or "y" to enable the parasitic
-+ power (2-wire, power-on-data) feature
-
-- extpullup GPIO for external pullup (default "5")
-+ extpullup GPIO for external pullup (default "5")
-
-
- Troubleshooting
diff --git a/target/linux/brcm2708/patches-4.4/0143-bcm2835-sdhost-Major-revision.patch b/target/linux/brcm2708/patches-4.4/0143-bcm2835-sdhost-Major-revision.patch
deleted file mode 100644
index 84170a2..0000000
--- a/target/linux/brcm2708/patches-4.4/0143-bcm2835-sdhost-Major-revision.patch
+++ /dev/null
@@ -1,2070 +0,0 @@
-From 545bbd2db8451d8e81a83aa1bbc0e8e5227a0503 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Thu, 11 Feb 2016 16:51:01 +0000
-Subject: [PATCH] bcm2835-sdhost: Major revision
-
-This is a significant revision of the bcm2835-sdhost driver. It
-improves on the original in a number of ways:
-
-1) Through the use of CMD23 for reads it appears to avoid problems
- reading some sectors on certain high speed cards.
-2) Better atomicity to prevent crashes.
-3) Higher performance.
-4) Activity logging included, for easier diagnosis in the event
- of a problem.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- drivers/mmc/host/bcm2835-sdhost.c | 1284 ++++++++++++++++++++-----------------
- 1 file changed, 686 insertions(+), 598 deletions(-)
-
---- a/drivers/mmc/host/bcm2835-sdhost.c
-+++ b/drivers/mmc/host/bcm2835-sdhost.c
-@@ -2,7 +2,7 @@
- * BCM2835 SD host driver.
- *
- * Author: Phil Elwell <phil at raspberrypi.org>
-- * Copyright 2015
-+ * Copyright (C) 2015-2016 Raspberry Pi (Trading) Ltd.
- *
- * Based on
- * mmc-bcm2835.c by Gellert Weisz
-@@ -24,12 +24,13 @@
- * along with this program. If not, see <http://www.gnu.org/licenses/>.
- */
-
--#define SAFE_READ_THRESHOLD 4
--#define SAFE_WRITE_THRESHOLD 4
--#define ALLOW_DMA 1
--#define ALLOW_CMD23 0
--#define ALLOW_FAST 1
--#define USE_BLOCK_IRQ 1
-+#define FIFO_READ_THRESHOLD 4
-+#define FIFO_WRITE_THRESHOLD 4
-+#define ALLOW_CMD23_READ 1
-+#define ALLOW_CMD23_WRITE 0
-+#define ENABLE_LOG 1
-+#define SDDATA_FIFO_PIO_BURST 8
-+#define CMD_DALLY_US 1
-
- #include <linux/delay.h>
- #include <linux/module.h>
-@@ -48,6 +49,7 @@
- #include <linux/dma-mapping.h>
- #include <linux/of_dma.h>
- #include <linux/time.h>
-+#include <linux/workqueue.h>
-
- #define DRIVER_NAME "sdhost-bcm2835"
-
-@@ -110,6 +112,28 @@
- #define SDEDM_READ_THRESHOLD_SHIFT 14
- #define SDEDM_THRESHOLD_MASK 0x1f
-
-+#define SDEDM_FSM_MASK 0xf
-+#define SDEDM_FSM_IDENTMODE 0x0
-+#define SDEDM_FSM_DATAMODE 0x1
-+#define SDEDM_FSM_READDATA 0x2
-+#define SDEDM_FSM_WRITEDATA 0x3
-+#define SDEDM_FSM_READWAIT 0x4
-+#define SDEDM_FSM_READCRC 0x5
-+#define SDEDM_FSM_WRITECRC 0x6
-+#define SDEDM_FSM_WRITEWAIT1 0x7
-+#define SDEDM_FSM_POWERDOWN 0x8
-+#define SDEDM_FSM_POWERUP 0x9
-+#define SDEDM_FSM_WRITESTART1 0xa
-+#define SDEDM_FSM_WRITESTART2 0xb
-+#define SDEDM_FSM_GENPULSES 0xc
-+#define SDEDM_FSM_WRITEWAIT2 0xd
-+#define SDEDM_FSM_STARTPOWDOWN 0xf
-+
-+#define SDDATA_FIFO_WORDS 16
-+
-+#define USE_CMD23_FLAGS ((ALLOW_CMD23_READ * MMC_DATA_READ) | \
-+ (ALLOW_CMD23_WRITE * MMC_DATA_WRITE))
-+
- #define MHZ 1000000
-
-
-@@ -131,15 +155,17 @@ struct bcm2835_host {
-
- struct tasklet_struct finish_tasklet; /* Tasklet structures */
-
-- struct timer_list timer; /* Timer for timeouts */
-+ struct work_struct cmd_wait_wq; /* Workqueue function */
-
-- struct timer_list pio_timer; /* PIO error detection timer */
-+ struct timer_list timer; /* Timer for timeouts */
-
- struct sg_mapping_iter sg_miter; /* SG state for PIO */
- unsigned int blocks; /* remaining PIO blocks */
-
- int irq; /* Device IRQ */
-
-+ u32 cmd_quick_poll_retries;
-+ u32 ns_per_fifo_word;
-
- /* cached registers */
- u32 hcfg;
-@@ -154,16 +180,21 @@ struct bcm2835_host {
-
- unsigned int use_busy:1; /* Wait for busy interrupt */
-
-- unsigned int debug:1; /* Enable debug output */
-+ unsigned int use_sbc:1; /* Send CMD23 */
-
-- u32 thread_isr;
-+ unsigned int debug:1; /* Enable debug output */
-
- /*DMA part*/
- struct dma_chan *dma_chan_rx; /* DMA channel for reads */
- struct dma_chan *dma_chan_tx; /* DMA channel for writes */
-+ struct dma_chan *dma_chan; /* Channel in used */
-+ struct dma_async_tx_descriptor *dma_desc;
-+ u32 dma_dir;
-+ u32 drain_words;
-+ struct page *drain_page;
-+ u32 drain_offset;
-
- bool allow_dma;
-- bool have_dma;
- bool use_dma;
- /*end of DMA part*/
-
-@@ -173,13 +204,98 @@ struct bcm2835_host {
- u32 overclock_50; /* frequency to use when 50MHz is requested (in MHz) */
- u32 overclock; /* Current frequency if overclocked, else zero */
- u32 pio_limit; /* Maximum block count for PIO (0 = always DMA) */
-+};
-
-- u32 debug_flags;
-+#if ENABLE_LOG
-
-- u32 sectors; /* Cached card size in sectors */
-- u32 single_read_sectors[8];
-+struct log_entry_struct {
-+ char event[4];
-+ u32 timestamp;
-+ u32 param1;
-+ u32 param2;
- };
-
-+typedef struct log_entry_struct LOG_ENTRY_T;
-+
-+LOG_ENTRY_T *sdhost_log_buf;
-+dma_addr_t sdhost_log_addr;
-+static u32 sdhost_log_idx;
-+static spinlock_t log_lock;
-+static void __iomem *timer_base;
-+
-+#define LOG_ENTRIES (256*1)
-+#define LOG_SIZE (sizeof(LOG_ENTRY_T)*LOG_ENTRIES)
-+
-+static void log_init(u32 bus_to_phys)
-+{
-+ spin_lock_init(&log_lock);
-+ sdhost_log_buf = dma_zalloc_coherent(NULL, LOG_SIZE, &sdhost_log_addr,
-+ GFP_KERNEL);
-+ if (sdhost_log_buf) {
-+ pr_err("sdhost: log_buf @ %p (%x)\n",
-+ sdhost_log_buf, sdhost_log_addr);
-+ timer_base = ioremap_nocache(bus_to_phys + 0x7e003000, SZ_4K);
-+ if (!timer_base)
-+ pr_err("sdhost: failed to remap timer\n");
-+ }
-+ else
-+ pr_err("sdhost: failed to allocate log buf\n");
-+}
-+
-+static void log_event_impl(const char *event, u32 param1, u32 param2)
-+{
-+ if (sdhost_log_buf) {
-+ LOG_ENTRY_T *entry;
-+ unsigned long flags;
-+
-+ spin_lock_irqsave(&log_lock, flags);
-+
-+ entry = sdhost_log_buf + sdhost_log_idx;
-+ memcpy(entry->event, event, 4);
-+ entry->timestamp = (readl(timer_base + 4) & 0x3fffffff) +
-+ (smp_processor_id()<<30);
-+ entry->param1 = param1;
-+ entry->param2 = param2;
-+ sdhost_log_idx = (sdhost_log_idx + 1) % LOG_ENTRIES;
-+
-+ spin_unlock_irqrestore(&log_lock, flags);
-+ }
-+}
-+
-+static void log_dump(void)
-+{
-+ if (sdhost_log_buf) {
-+ LOG_ENTRY_T *entry;
-+ unsigned long flags;
-+ int idx;
-+
-+ spin_lock_irqsave(&log_lock, flags);
-+
-+ idx = sdhost_log_idx;
-+ do {
-+ entry = sdhost_log_buf + idx;
-+ if (entry->event[0] != '\0')
-+ pr_err("[%08x] %.4s %x %x\n",
-+ entry->timestamp,
-+ entry->event,
-+ entry->param1,
-+ entry->param2);
-+ idx = (idx + 1) % LOG_ENTRIES;
-+ } while (idx != sdhost_log_idx);
-+
-+ spin_unlock_irqrestore(&log_lock, flags);
-+ }
-+}
-+
-+#define log_event(event, param1, param2) log_event_impl(event, param1, param2)
-+
-+#else
-+
-+#define log_init(x) (void)0
-+#define log_event(event, param1, param2) (void)0
-+#define log_dump() (void)0
-+
-+#endif
-
- static inline void bcm2835_sdhost_write(struct bcm2835_host *host, u32 val, int reg)
- {
-@@ -201,7 +317,7 @@ static void bcm2835_sdhost_dumpcmd(struc
- const char *label)
- {
- if (cmd)
-- pr_info("%s:%c%s op %d arg 0x%x flags 0x%x - resp %08x %08x %08x %08x, err %d\n",
-+ pr_err("%s:%c%s op %d arg 0x%x flags 0x%x - resp %08x %08x %08x %08x, err %d\n",
- mmc_hostname(host->mmc),
- (cmd == host->cmd) ? '>' : ' ',
- label, cmd->opcode, cmd->arg, cmd->flags,
-@@ -211,73 +327,74 @@ static void bcm2835_sdhost_dumpcmd(struc
-
- static void bcm2835_sdhost_dumpregs(struct bcm2835_host *host)
- {
-- bcm2835_sdhost_dumpcmd(host, host->mrq->sbc, "sbc");
-- bcm2835_sdhost_dumpcmd(host, host->mrq->cmd, "cmd");
-- if (host->mrq->data)
-- pr_err("%s: data blocks %x blksz %x - err %d\n",
-- mmc_hostname(host->mmc),
-- host->mrq->data->blocks,
-- host->mrq->data->blksz,
-- host->mrq->data->error);
-- bcm2835_sdhost_dumpcmd(host, host->mrq->stop, "stop");
-+ if (host->mrq)
-+ {
-+ bcm2835_sdhost_dumpcmd(host, host->mrq->sbc, "sbc");
-+ bcm2835_sdhost_dumpcmd(host, host->mrq->cmd, "cmd");
-+ if (host->mrq->data)
-+ pr_err("%s: data blocks %x blksz %x - err %d\n",
-+ mmc_hostname(host->mmc),
-+ host->mrq->data->blocks,
-+ host->mrq->data->blksz,
-+ host->mrq->data->error);
-+ bcm2835_sdhost_dumpcmd(host, host->mrq->stop, "stop");
-+ }
-
-- pr_info("%s: =========== REGISTER DUMP ===========\n",
-+ pr_err("%s: =========== REGISTER DUMP ===========\n",
- mmc_hostname(host->mmc));
-
-- pr_info("%s: SDCMD 0x%08x\n",
-+ pr_err("%s: SDCMD 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDCMD));
-- pr_info("%s: SDARG 0x%08x\n",
-+ pr_err("%s: SDARG 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDARG));
-- pr_info("%s: SDTOUT 0x%08x\n",
-+ pr_err("%s: SDTOUT 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDTOUT));
-- pr_info("%s: SDCDIV 0x%08x\n",
-+ pr_err("%s: SDCDIV 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDCDIV));
-- pr_info("%s: SDRSP0 0x%08x\n",
-+ pr_err("%s: SDRSP0 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDRSP0));
-- pr_info("%s: SDRSP1 0x%08x\n",
-+ pr_err("%s: SDRSP1 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDRSP1));
-- pr_info("%s: SDRSP2 0x%08x\n",
-+ pr_err("%s: SDRSP2 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDRSP2));
-- pr_info("%s: SDRSP3 0x%08x\n",
-+ pr_err("%s: SDRSP3 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDRSP3));
-- pr_info("%s: SDHSTS 0x%08x\n",
-+ pr_err("%s: SDHSTS 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDHSTS));
-- pr_info("%s: SDVDD 0x%08x\n",
-+ pr_err("%s: SDVDD 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDVDD));
-- pr_info("%s: SDEDM 0x%08x\n",
-+ pr_err("%s: SDEDM 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDEDM));
-- pr_info("%s: SDHCFG 0x%08x\n",
-+ pr_err("%s: SDHCFG 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDHCFG));
-- pr_info("%s: SDHBCT 0x%08x\n",
-+ pr_err("%s: SDHBCT 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDHBCT));
-- pr_info("%s: SDHBLC 0x%08x\n",
-+ pr_err("%s: SDHBLC 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDHBLC));
-
-- pr_info("%s: ===========================================\n",
-+ pr_err("%s: ===========================================\n",
- mmc_hostname(host->mmc));
- }
-
--
- static void bcm2835_sdhost_set_power(struct bcm2835_host *host, bool on)
- {
- bcm2835_sdhost_write(host, on ? 1 : 0, SDVDD);
- }
-
--
- static void bcm2835_sdhost_reset_internal(struct bcm2835_host *host)
- {
- u32 temp;
-@@ -300,26 +417,24 @@ static void bcm2835_sdhost_reset_interna
- temp = bcm2835_sdhost_read(host, SDEDM);
- temp &= ~((SDEDM_THRESHOLD_MASK<<SDEDM_READ_THRESHOLD_SHIFT) |
- (SDEDM_THRESHOLD_MASK<<SDEDM_WRITE_THRESHOLD_SHIFT));
-- temp |= (SAFE_READ_THRESHOLD << SDEDM_READ_THRESHOLD_SHIFT) |
-- (SAFE_WRITE_THRESHOLD << SDEDM_WRITE_THRESHOLD_SHIFT);
-+ temp |= (FIFO_READ_THRESHOLD << SDEDM_READ_THRESHOLD_SHIFT) |
-+ (FIFO_WRITE_THRESHOLD << SDEDM_WRITE_THRESHOLD_SHIFT);
- bcm2835_sdhost_write(host, temp, SDEDM);
- mdelay(10);
- bcm2835_sdhost_set_power(host, true);
- mdelay(10);
- host->clock = 0;
-- host->sectors = 0;
-- host->single_read_sectors[0] = ~0;
- bcm2835_sdhost_write(host, host->hcfg, SDHCFG);
- bcm2835_sdhost_write(host, host->cdiv, SDCDIV);
- mmiowb();
- }
-
--
- static void bcm2835_sdhost_reset(struct mmc_host *mmc)
- {
- struct bcm2835_host *host = mmc_priv(mmc);
- unsigned long flags;
- spin_lock_irqsave(&host->lock, flags);
-+ log_event("RST<", 0, 0);
-
- bcm2835_sdhost_reset_internal(host);
-
-@@ -344,82 +459,48 @@ static void bcm2835_sdhost_init(struct b
- }
- }
-
--static bool bcm2835_sdhost_is_write_complete(struct bcm2835_host *host)
-+static void bcm2835_sdhost_wait_transfer_complete(struct bcm2835_host *host)
- {
-- bool write_complete = ((bcm2835_sdhost_read(host, SDEDM) & 0xf) == 1);
-+ int timediff;
-+ u32 alternate_idle;
-+ u32 edm;
-
-- if (!write_complete) {
-- /* Request an IRQ for the last block */
-- host->hcfg |= SDHCFG_BLOCK_IRPT_EN;
-- bcm2835_sdhost_write(host, host->hcfg, SDHCFG);
-- if ((bcm2835_sdhost_read(host, SDEDM) & 0xf) == 1) {
-- /* The write has now completed. Disable the interrupt
-- and clear the status flag */
-- host->hcfg &= ~SDHCFG_BLOCK_IRPT_EN;
-- bcm2835_sdhost_write(host, host->hcfg, SDHCFG);
-- bcm2835_sdhost_write(host, SDHSTS_BLOCK_IRPT, SDHSTS);
-- write_complete = true;
-- }
-- }
-+ alternate_idle = (host->mrq->data->flags & MMC_DATA_READ) ?
-+ SDEDM_FSM_READWAIT : SDEDM_FSM_WRITESTART1;
-
-- return write_complete;
--}
-+ edm = bcm2835_sdhost_read(host, SDEDM);
-
--static void bcm2835_sdhost_wait_write_complete(struct bcm2835_host *host)
--{
-- int timediff;
--#ifdef DEBUG
-- static struct timeval start_time;
-- static int max_stall_time = 0;
-- static int total_stall_time = 0;
-- struct timeval before, after;
--
-- do_gettimeofday(&before);
-- if (max_stall_time == 0)
-- start_time = before;
--#endif
-+ log_event("WTC<", edm, 0);
-
- timediff = 0;
-
- while (1) {
-- u32 edm = bcm2835_sdhost_read(host, SDEDM);
-- if ((edm & 0xf) == 1)
-+ u32 fsm = edm & SDEDM_FSM_MASK;
-+ if ((fsm == SDEDM_FSM_IDENTMODE) ||
-+ (fsm == SDEDM_FSM_DATAMODE))
- break;
-- timediff++;
-- if (timediff > 5000000) {
--#ifdef DEBUG
-- do_gettimeofday(&after);
-- timediff = (after.tv_sec - before.tv_sec)*1000000 +
-- (after.tv_usec - before.tv_usec);
-+ if (fsm == alternate_idle) {
-+ bcm2835_sdhost_write(host,
-+ edm | SDEDM_FORCE_DATA_MODE,
-+ SDEDM);
-+ break;
-+ }
-
-- pr_err(" wait_write_complete - still waiting after %dus\n",
-- timediff);
--#else
-- pr_err(" wait_write_complete - still waiting after %d retries\n",
-+ timediff++;
-+ if (timediff == 100000) {
-+ pr_err("%s: wait_transfer_complete - still waiting after %d retries\n",
-+ mmc_hostname(host->mmc),
- timediff);
--#endif
-+ log_dump();
- bcm2835_sdhost_dumpregs(host);
-- host->data->error = -ETIMEDOUT;
-+ host->mrq->data->error = -ETIMEDOUT;
-+ log_event("WTC!", edm, 0);
- return;
- }
-+ cpu_relax();
-+ edm = bcm2835_sdhost_read(host, SDEDM);
- }
--
--#ifdef DEBUG
-- do_gettimeofday(&after);
-- timediff = (after.tv_sec - before.tv_sec)*1000000 + (after.tv_usec - before.tv_usec);
--
-- total_stall_time += timediff;
-- if (timediff > max_stall_time)
-- max_stall_time = timediff;
--
-- if ((after.tv_sec - start_time.tv_sec) > 10) {
-- pr_debug(" wait_write_complete - max wait %dus, total %dus\n",
-- max_stall_time, total_stall_time);
-- start_time = after;
-- max_stall_time = 0;
-- total_stall_time = 0;
-- }
--#endif
-+ log_event("WTC>", edm, 0);
- }
-
- static void bcm2835_sdhost_finish_data(struct bcm2835_host *host);
-@@ -427,65 +508,44 @@ static void bcm2835_sdhost_finish_data(s
- static void bcm2835_sdhost_dma_complete(void *param)
- {
- struct bcm2835_host *host = param;
-- struct dma_chan *dma_chan;
-+ struct mmc_data *data = host->data;
- unsigned long flags;
-- u32 dir_data;
-
- spin_lock_irqsave(&host->lock, flags);
-+ log_event("DMA<", (u32)host->data, bcm2835_sdhost_read(host, SDHSTS));
-+ log_event("DMA ", bcm2835_sdhost_read(host, SDCMD),
-+ bcm2835_sdhost_read(host, SDEDM));
-
-- if (host->data) {
-- bool write_complete;
-- if (USE_BLOCK_IRQ)
-- write_complete = bcm2835_sdhost_is_write_complete(host);
-- else {
-- bcm2835_sdhost_wait_write_complete(host);
-- write_complete = true;
-- }
-- pr_debug("dma_complete() - write_complete=%d\n",
-- write_complete);
--
-- if (write_complete || (host->data->flags & MMC_DATA_READ))
-- {
-- if (write_complete) {
-- dma_chan = host->dma_chan_tx;
-- dir_data = DMA_TO_DEVICE;
-- } else {
-- dma_chan = host->dma_chan_rx;
-- dir_data = DMA_FROM_DEVICE;
-- }
--
-- dma_unmap_sg(dma_chan->device->dev,
-- host->data->sg, host->data->sg_len,
-- dir_data);
-+ if (host->dma_chan) {
-+ dma_unmap_sg(host->dma_chan->device->dev,
-+ data->sg, data->sg_len,
-+ host->dma_dir);
-
-- bcm2835_sdhost_finish_data(host);
-- }
-+ host->dma_chan = NULL;
- }
-
-- spin_unlock_irqrestore(&host->lock, flags);
--}
-+ if (host->drain_words) {
-+ void *page;
-+ u32 *buf;
-
--static bool data_transfer_wait(struct bcm2835_host *host)
--{
-- unsigned long timeout = 1000000;
-- while (timeout)
-- {
-- u32 sdhsts = bcm2835_sdhost_read(host, SDHSTS);
-- if (sdhsts & SDHSTS_DATA_FLAG) {
-- bcm2835_sdhost_write(host, SDHSTS_DATA_FLAG, SDHSTS);
-- break;
-+ page = kmap_atomic(host->drain_page);
-+ buf = page + host->drain_offset;
-+
-+ while (host->drain_words) {
-+ u32 edm = bcm2835_sdhost_read(host, SDEDM);
-+ if ((edm >> 4) & 0x1f)
-+ *(buf++) = bcm2835_sdhost_read(host,
-+ SDDATA);
-+ host->drain_words--;
- }
-- timeout--;
-- }
-- if (timeout == 0) {
-- pr_err("%s: Data %s timeout\n",
-- mmc_hostname(host->mmc),
-- (host->data->flags & MMC_DATA_READ) ? "read" : "write");
-- bcm2835_sdhost_dumpregs(host);
-- host->data->error = -ETIMEDOUT;
-- return false;
-+
-+ kunmap_atomic(page);
- }
-- return true;
-+
-+ bcm2835_sdhost_finish_data(host);
-+
-+ log_event("DMA>", (u32)host->data, 0);
-+ spin_unlock_irqrestore(&host->lock, flags);
- }
-
- static void bcm2835_sdhost_read_block_pio(struct bcm2835_host *host)
-@@ -493,32 +553,83 @@ static void bcm2835_sdhost_read_block_pi
- unsigned long flags;
- size_t blksize, len;
- u32 *buf;
-+ unsigned long wait_max;
-
- blksize = host->data->blksz;
-
-+ wait_max = jiffies + msecs_to_jiffies(host->pio_timeout);
-+
- local_irq_save(flags);
-
- while (blksize) {
-- if (!sg_miter_next(&host->sg_miter))
-- BUG();
-+ int copy_words;
-+ u32 hsts = 0;
-+
-+ if (!sg_miter_next(&host->sg_miter)) {
-+ host->data->error = -EINVAL;
-+ break;
-+ }
-
- len = min(host->sg_miter.length, blksize);
-- BUG_ON(len % 4);
-+ if (len % 4) {
-+ host->data->error = -EINVAL;
-+ break;
-+ }
-
- blksize -= len;
- host->sg_miter.consumed = len;
-
- buf = (u32 *)host->sg_miter.addr;
-
-- while (len) {
-- if (!data_transfer_wait(host))
-- break;
-+ copy_words = len/4;
-+
-+ while (copy_words) {
-+ int burst_words, words;
-+ u32 edm;
-+
-+ burst_words = SDDATA_FIFO_PIO_BURST;
-+ if (burst_words > copy_words)
-+ burst_words = copy_words;
-+ edm = bcm2835_sdhost_read(host, SDEDM);
-+ words = ((edm >> 4) & 0x1f);
-+
-+ if (words < burst_words) {
-+ int fsm_state = (edm & SDEDM_FSM_MASK);
-+ if ((fsm_state != SDEDM_FSM_READDATA) &&
-+ (fsm_state != SDEDM_FSM_READWAIT) &&
-+ (fsm_state != SDEDM_FSM_READCRC)) {
-+ hsts = bcm2835_sdhost_read(host,
-+ SDHSTS);
-+ pr_err("%s: fsm %x, hsts %x\n",
-+ mmc_hostname(host->mmc),
-+ fsm_state, hsts);
-+ if (hsts & SDHSTS_ERROR_MASK)
-+ break;
-+ }
-+
-+ if (time_after(jiffies, wait_max)) {
-+ pr_err("%s: PIO read timeout - EDM %x\n",
-+ mmc_hostname(host->mmc),
-+ edm);
-+ hsts = SDHSTS_REW_TIME_OUT;
-+ break;
-+ }
-+ ndelay((burst_words - words) *
-+ host->ns_per_fifo_word);
-+ continue;
-+ } else if (words > copy_words) {
-+ words = copy_words;
-+ }
-+
-+ copy_words -= words;
-
-- *(buf++) = bcm2835_sdhost_read(host, SDDATA);
-- len -= 4;
-+ while (words) {
-+ *(buf++) = bcm2835_sdhost_read(host, SDDATA);
-+ words--;
-+ }
- }
-
-- if (host->data->error)
-+ if (hsts & SDHSTS_ERROR_MASK)
- break;
- }
-
-@@ -532,32 +643,83 @@ static void bcm2835_sdhost_write_block_p
- unsigned long flags;
- size_t blksize, len;
- u32 *buf;
-+ unsigned long wait_max;
-
- blksize = host->data->blksz;
-
-+ wait_max = jiffies + msecs_to_jiffies(host->pio_timeout);
-+
- local_irq_save(flags);
-
- while (blksize) {
-- if (!sg_miter_next(&host->sg_miter))
-- BUG();
-+ int copy_words;
-+ u32 hsts = 0;
-+
-+ if (!sg_miter_next(&host->sg_miter)) {
-+ host->data->error = -EINVAL;
-+ break;
-+ }
-
- len = min(host->sg_miter.length, blksize);
-- BUG_ON(len % 4);
-+ if (len % 4) {
-+ host->data->error = -EINVAL;
-+ break;
-+ }
-
- blksize -= len;
- host->sg_miter.consumed = len;
-
-- buf = host->sg_miter.addr;
-+ buf = (u32 *)host->sg_miter.addr;
-
-- while (len) {
-- if (!data_transfer_wait(host))
-- break;
-+ copy_words = len/4;
-+
-+ while (copy_words) {
-+ int burst_words, words;
-+ u32 edm;
-+
-+ burst_words = SDDATA_FIFO_PIO_BURST;
-+ if (burst_words > copy_words)
-+ burst_words = copy_words;
-+ edm = bcm2835_sdhost_read(host, SDEDM);
-+ words = SDDATA_FIFO_WORDS - ((edm >> 4) & 0x1f);
-+
-+ if (words < burst_words) {
-+ int fsm_state = (edm & SDEDM_FSM_MASK);
-+ if ((fsm_state != SDEDM_FSM_WRITEDATA) &&
-+ (fsm_state != SDEDM_FSM_WRITESTART1) &&
-+ (fsm_state != SDEDM_FSM_WRITESTART2)) {
-+ hsts = bcm2835_sdhost_read(host,
-+ SDHSTS);
-+ pr_err("%s: fsm %x, hsts %x\n",
-+ mmc_hostname(host->mmc),
-+ fsm_state, hsts);
-+ if (hsts & SDHSTS_ERROR_MASK)
-+ break;
-+ }
-
-- bcm2835_sdhost_write(host, *(buf++), SDDATA);
-- len -= 4;
-+ if (time_after(jiffies, wait_max)) {
-+ pr_err("%s: PIO write timeout - EDM %x\n",
-+ mmc_hostname(host->mmc),
-+ edm);
-+ hsts = SDHSTS_REW_TIME_OUT;
-+ break;
-+ }
-+ ndelay((burst_words - words) *
-+ host->ns_per_fifo_word);
-+ continue;
-+ } else if (words > copy_words) {
-+ words = copy_words;
-+ }
-+
-+ copy_words -= words;
-+
-+ while (words) {
-+ bcm2835_sdhost_write(host, *(buf++), SDDATA);
-+ words--;
-+ }
- }
-
-- if (host->data->error)
-+ if (hsts & SDHSTS_ERROR_MASK)
- break;
- }
-
-@@ -566,12 +728,12 @@ static void bcm2835_sdhost_write_block_p
- local_irq_restore(flags);
- }
-
--
- static void bcm2835_sdhost_transfer_pio(struct bcm2835_host *host)
- {
- u32 sdhsts;
- bool is_read;
- BUG_ON(!host->data);
-+ log_event("XFP<", (u32)host->data, host->blocks);
-
- is_read = (host->data->flags & MMC_DATA_READ) != 0;
- if (is_read)
-@@ -595,28 +757,21 @@ static void bcm2835_sdhost_transfer_pio(
- is_read ? "read" : "write",
- sdhsts);
- host->data->error = -ETIMEDOUT;
-- } else if (!is_read && !host->data->error) {
-- /* Start a timer in case a transfer error occurs because
-- there is no error interrupt */
-- mod_timer(&host->pio_timer, jiffies + host->pio_timeout);
- }
-+ log_event("XFP>", (u32)host->data, host->blocks);
- }
-
--
--static void bcm2835_sdhost_transfer_dma(struct bcm2835_host *host)
-+static void bcm2835_sdhost_prepare_dma(struct bcm2835_host *host,
-+ struct mmc_data *data)
- {
-- u32 len, dir_data, dir_slave;
-+ int len, dir_data, dir_slave;
- struct dma_async_tx_descriptor *desc = NULL;
- struct dma_chan *dma_chan;
-
-- pr_debug("bcm2835_sdhost_transfer_dma()\n");
--
-- WARN_ON(!host->data);
-+ log_event("PRD<", (u32)data, 0);
-+ pr_debug("bcm2835_sdhost_prepare_dma()\n");
-
-- if (!host->data)
-- return;
--
-- if (host->data->flags & MMC_DATA_READ) {
-+ if (data->flags & MMC_DATA_READ) {
- dma_chan = host->dma_chan_rx;
- dir_data = DMA_FROM_DEVICE;
- dir_slave = DMA_DEV_TO_MEM;
-@@ -625,35 +780,71 @@ static void bcm2835_sdhost_transfer_dma(
- dir_data = DMA_TO_DEVICE;
- dir_slave = DMA_MEM_TO_DEV;
- }
-+ log_event("PRD1", (u32)dma_chan, 0);
-
- BUG_ON(!dma_chan->device);
- BUG_ON(!dma_chan->device->dev);
-- BUG_ON(!host->data->sg);
-+ BUG_ON(!data->sg);
-
-- len = dma_map_sg(dma_chan->device->dev, host->data->sg,
-- host->data->sg_len, dir_data);
-- if (len > 0) {
-- desc = dmaengine_prep_slave_sg(dma_chan, host->data->sg,
-+ /* The block doesn't manage the FIFO DREQs properly for multi-block
-+ transfers, so don't attempt to DMA the final few words.
-+ Unfortunately this requires the final sg entry to be trimmed.
-+ N.B. This code demands that the overspill is contained in
-+ a single sg entry.
-+ */
-+
-+ host->drain_words = 0;
-+ if ((data->blocks > 1) && (dir_data == DMA_FROM_DEVICE)) {
-+ struct scatterlist *sg;
-+ u32 len;
-+ int i;
-+
-+ len = min((u32)(FIFO_READ_THRESHOLD - 1) * 4,
-+ (u32)data->blocks * data->blksz);
-+
-+ for_each_sg(data->sg, sg, data->sg_len, i) {
-+ if (sg_is_last(sg)) {
-+ BUG_ON(sg->length < len);
-+ sg->length -= len;
-+ host->drain_page = (struct page *)sg->page_link;
-+ host->drain_offset = sg->offset + sg->length;
-+ }
-+ }
-+ host->drain_words = len/4;
-+ }
-+
-+ len = dma_map_sg(dma_chan->device->dev, data->sg, data->sg_len,
-+ dir_data);
-+
-+ log_event("PRD2", len, 0);
-+ if (len > 0)
-+ desc = dmaengine_prep_slave_sg(dma_chan, data->sg,
- len, dir_slave,
- DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
-- } else {
-- dev_err(mmc_dev(host->mmc), "dma_map_sg returned zero length\n");
-- }
-+ log_event("PRD3", (u32)desc, 0);
-+
- if (desc) {
- desc->callback = bcm2835_sdhost_dma_complete;
- desc->callback_param = host;
-- dmaengine_submit(desc);
-- dma_async_issue_pending(dma_chan);
-+ host->dma_desc = desc;
-+ host->dma_chan = dma_chan;
-+ host->dma_dir = dir_data;
- }
--
-+ log_event("PDM>", (u32)data, 0);
- }
-
-+static void bcm2835_sdhost_start_dma(struct bcm2835_host *host)
-+{
-+ log_event("SDMA", (u32)host->data, (u32)host->dma_chan);
-+ dmaengine_submit(host->dma_desc);
-+ dma_async_issue_pending(host->dma_chan);
-+}
-
- static void bcm2835_sdhost_set_transfer_irqs(struct bcm2835_host *host)
- {
- u32 all_irqs = SDHCFG_DATA_IRPT_EN | SDHCFG_BLOCK_IRPT_EN |
- SDHCFG_BUSY_IRPT_EN;
-- if (host->use_dma)
-+ if (host->dma_desc)
- host->hcfg = (host->hcfg & ~all_irqs) |
- SDHCFG_BUSY_IRPT_EN;
- else
-@@ -664,13 +855,13 @@ static void bcm2835_sdhost_set_transfer_
- bcm2835_sdhost_write(host, host->hcfg, SDHCFG);
- }
-
--
- static void bcm2835_sdhost_prepare_data(struct bcm2835_host *host, struct mmc_command *cmd)
- {
- struct mmc_data *data = cmd->data;
-
- WARN_ON(host->data);
-
-+ host->data = data;
- if (!data)
- return;
-
-@@ -679,46 +870,19 @@ static void bcm2835_sdhost_prepare_data(
- BUG_ON(data->blksz > host->mmc->max_blk_size);
- BUG_ON(data->blocks > 65535);
-
-- host->data = data;
- host->data_complete = 0;
- host->flush_fifo = 0;
- host->data->bytes_xfered = 0;
-
-- if (!host->sectors && host->mmc->card && !(host->debug_flags & 1))
-- {
-- struct mmc_card *card = host->mmc->card;
-- if (!mmc_card_sd(card) && mmc_card_blockaddr(card)) {
-- /*
-- * The EXT_CSD sector count is in number of 512 byte
-- * sectors.
-- */
-- host->sectors = card->ext_csd.sectors;
-- pr_err("%s: using ext_csd!\n", mmc_hostname(host->mmc));
-- } else {
-- /*
-- * The CSD capacity field is in units of read_blkbits.
-- * set_capacity takes units of 512 bytes.
-- */
-- host->sectors = card->csd.capacity <<
-- (card->csd.read_blkbits - 9);
-- }
-- host->single_read_sectors[0] = host->sectors - 65;
-- host->single_read_sectors[1] = host->sectors - 64;
-- host->single_read_sectors[2] = host->sectors - 33;
-- host->single_read_sectors[3] = host->sectors - 32;
-- host->single_read_sectors[4] = host->sectors - 1;
-- host->single_read_sectors[5] = ~0; /* Safety net */
-- }
-
-- host->use_dma = host->have_dma && (data->blocks > host->pio_limit);
-- if (!host->use_dma) {
-+ if (!host->dma_desc) {
-+ /* Use PIO */
- int flags;
-
-- flags = SG_MITER_ATOMIC;
- if (data->flags & MMC_DATA_READ)
-- flags |= SG_MITER_TO_SG;
-+ flags = SG_MITER_TO_SG;
- else
-- flags |= SG_MITER_FROM_SG;
-+ flags = SG_MITER_FROM_SG;
- sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags);
- host->blocks = data->blocks;
- }
-@@ -726,19 +890,20 @@ static void bcm2835_sdhost_prepare_data(
- bcm2835_sdhost_set_transfer_irqs(host);
-
- bcm2835_sdhost_write(host, data->blksz, SDHBCT);
-- bcm2835_sdhost_write(host, host->use_dma ? data->blocks : 0, SDHBLC);
-+ bcm2835_sdhost_write(host, data->blocks, SDHBLC);
-
- BUG_ON(!host->data);
- }
-
--
--void bcm2835_sdhost_send_command(struct bcm2835_host *host, struct mmc_command *cmd)
-+bool bcm2835_sdhost_send_command(struct bcm2835_host *host,
-+ struct mmc_command *cmd)
- {
- u32 sdcmd, sdhsts;
- unsigned long timeout;
- int delay;
-
- WARN_ON(host->cmd);
-+ log_event("CMD<", cmd->opcode, cmd->arg);
-
- if (cmd->data)
- pr_debug("%s: send_command %d 0x%x "
-@@ -761,9 +926,9 @@ void bcm2835_sdhost_send_command(struct
- pr_err("%s: previous command never completed.\n",
- mmc_hostname(host->mmc));
- bcm2835_sdhost_dumpregs(host);
-- cmd->error = -EIO;
-+ cmd->error = -EILSEQ;
- tasklet_schedule(&host->finish_tasklet);
-- return;
-+ return false;
- }
- timeout--;
- udelay(10);
-@@ -791,23 +956,24 @@ void bcm2835_sdhost_send_command(struct
- if (sdhsts & SDHSTS_ERROR_MASK)
- bcm2835_sdhost_write(host, sdhsts, SDHSTS);
-
-- bcm2835_sdhost_prepare_data(host, cmd);
--
-- bcm2835_sdhost_write(host, cmd->arg, SDARG);
--
- if ((cmd->flags & MMC_RSP_136) && (cmd->flags & MMC_RSP_BUSY)) {
- pr_err("%s: unsupported response type!\n",
- mmc_hostname(host->mmc));
- cmd->error = -EINVAL;
- tasklet_schedule(&host->finish_tasklet);
-- return;
-+ return false;
- }
-
-+ bcm2835_sdhost_prepare_data(host, cmd);
-+
-+ bcm2835_sdhost_write(host, cmd->arg, SDARG);
-+
- sdcmd = cmd->opcode & SDCMD_CMD_MASK;
-
-- if (!(cmd->flags & MMC_RSP_PRESENT))
-+ host->use_busy = 0;
-+ if (!(cmd->flags & MMC_RSP_PRESENT)) {
- sdcmd |= SDCMD_NO_RESPONSE;
-- else {
-+ } else {
- if (cmd->flags & MMC_RSP_136)
- sdcmd |= SDCMD_LONG_RESPONSE;
- if (cmd->flags & MMC_RSP_BUSY) {
-@@ -817,6 +983,7 @@ void bcm2835_sdhost_send_command(struct
- }
-
- if (cmd->data) {
-+ log_event("CMDD", cmd->data->blocks, cmd->data->blksz);
- if (host->delay_after_stop) {
- struct timeval now;
- int time_since_stop;
-@@ -839,10 +1006,12 @@ void bcm2835_sdhost_send_command(struct
- }
-
- bcm2835_sdhost_write(host, sdcmd | SDCMD_NEW_FLAG, SDCMD);
--}
-
-+ return true;
-+}
-
--static void bcm2835_sdhost_finish_command(struct bcm2835_host *host);
-+static void bcm2835_sdhost_finish_command(struct bcm2835_host *host,
-+ unsigned long *irq_flags);
- static void bcm2835_sdhost_transfer_complete(struct bcm2835_host *host);
-
- static void bcm2835_sdhost_finish_data(struct bcm2835_host *host)
-@@ -852,6 +1021,7 @@ static void bcm2835_sdhost_finish_data(s
- data = host->data;
- BUG_ON(!data);
-
-+ log_event("FDA<", (u32)host->mrq, (u32)host->cmd);
- pr_debug("finish_data(error %d, stop %d, sbc %d)\n",
- data->error, data->stop ? 1 : 0,
- host->mrq->sbc ? 1 : 0);
-@@ -859,10 +1029,7 @@ static void bcm2835_sdhost_finish_data(s
- host->hcfg &= ~(SDHCFG_DATA_IRPT_EN | SDHCFG_BLOCK_IRPT_EN);
- bcm2835_sdhost_write(host, host->hcfg, SDHCFG);
-
-- if (data->error) {
-- data->bytes_xfered = 0;
-- } else
-- data->bytes_xfered = data->blksz * data->blocks;
-+ data->bytes_xfered = data->error ? 0 : (data->blksz * data->blocks);
-
- host->data_complete = 1;
-
-@@ -877,9 +1044,9 @@ static void bcm2835_sdhost_finish_data(s
- }
- else
- bcm2835_sdhost_transfer_complete(host);
-+ log_event("FDA>", (u32)host->mrq, (u32)host->cmd);
- }
-
--
- static void bcm2835_sdhost_transfer_complete(struct bcm2835_host *host)
- {
- struct mmc_data *data;
-@@ -891,6 +1058,7 @@ static void bcm2835_sdhost_transfer_comp
- data = host->data;
- host->data = NULL;
-
-+ log_event("TCM<", (u32)data, data->error);
- pr_debug("transfer_complete(error %d, stop %d)\n",
- data->error, data->stop ? 1 : 0);
-
-@@ -899,88 +1067,114 @@ static void bcm2835_sdhost_transfer_comp
- * a) open-ended multiblock transfer (no CMD23)
- * b) error in multiblock transfer
- */
-- if (data->stop &&
-- (data->error ||
-- !host->mrq->sbc)) {
-- host->flush_fifo = 1;
-- bcm2835_sdhost_send_command(host, data->stop);
-- if (host->delay_after_stop)
-- do_gettimeofday(&host->stop_time);
-- if (!host->use_busy)
-- bcm2835_sdhost_finish_command(host);
-+ if (host->mrq->stop && (data->error || !host->use_sbc)) {
-+ if (bcm2835_sdhost_send_command(host, host->mrq->stop)) {
-+ /* No busy, so poll for completion */
-+ if (!host->use_busy)
-+ bcm2835_sdhost_finish_command(host, NULL);
-+
-+ if (host->delay_after_stop)
-+ do_gettimeofday(&host->stop_time);
-+ }
- } else {
-+ bcm2835_sdhost_wait_transfer_complete(host);
- tasklet_schedule(&host->finish_tasklet);
- }
-+ log_event("TCM>", (u32)data, 0);
- }
-
--static void bcm2835_sdhost_finish_command(struct bcm2835_host *host)
-+/* If irq_flags is valid, the caller is in a thread context and is allowed
-+ to sleep */
-+static void bcm2835_sdhost_finish_command(struct bcm2835_host *host,
-+ unsigned long *irq_flags)
- {
- u32 sdcmd;
-- unsigned long timeout;
-+ u32 retries;
- #ifdef DEBUG
- struct timeval before, after;
- int timediff = 0;
- #endif
-
-+ log_event("FCM<", (u32)host->mrq, (u32)host->cmd);
- pr_debug("finish_command(%x)\n", bcm2835_sdhost_read(host, SDCMD));
-
- BUG_ON(!host->cmd || !host->mrq);
-
--#ifdef DEBUG
-- do_gettimeofday(&before);
--#endif
-- /* Wait max 100 ms */
-- timeout = 10000;
-+ /* Poll quickly at first */
-+
-+ retries = host->cmd_quick_poll_retries;
-+ if (!retries) {
-+ /* Work out how many polls take 1us by timing 10us */
-+ struct timeval start, now;
-+ int us_diff;
-+
-+ retries = 1;
-+ do {
-+ int i;
-+
-+ retries *= 2;
-+
-+ do_gettimeofday(&start);
-+
-+ for (i = 0; i < retries; i++) {
-+ cpu_relax();
-+ sdcmd = bcm2835_sdhost_read(host, SDCMD);
-+ }
-+
-+ do_gettimeofday(&now);
-+ us_diff = (now.tv_sec - start.tv_sec) * 1000000 +
-+ (now.tv_usec - start.tv_usec);
-+ } while (us_diff < 10);
-+
-+ host->cmd_quick_poll_retries = ((retries * us_diff + 9)*CMD_DALLY_US)/10 + 1;
-+ retries = 1; // We've already waited long enough this time
-+ }
-+
-+ retries = host->cmd_quick_poll_retries;
- for (sdcmd = bcm2835_sdhost_read(host, SDCMD);
-- (sdcmd & SDCMD_NEW_FLAG) && timeout;
-- timeout--) {
-- if (host->flush_fifo) {
-- while (bcm2835_sdhost_read(host, SDHSTS) &
-- SDHSTS_DATA_FLAG)
-- (void)bcm2835_sdhost_read(host, SDDATA);
-- }
-- udelay(10);
-+ (sdcmd & SDCMD_NEW_FLAG) && !(sdcmd & SDCMD_FAIL_FLAG) && retries;
-+ retries--) {
-+ cpu_relax();
- sdcmd = bcm2835_sdhost_read(host, SDCMD);
- }
--#ifdef DEBUG
-- do_gettimeofday(&after);
-- timediff = (after.tv_sec - before.tv_sec)*1000000 +
-- (after.tv_usec - before.tv_usec);
-
-- pr_debug(" finish_command - waited %dus\n", timediff);
--#endif
-+ if (!retries) {
-+ unsigned long wait_max;
-+
-+ if (!irq_flags) {
-+ /* Schedule the work */
-+ log_event("CWWQ", 0, 0);
-+ schedule_work(&host->cmd_wait_wq);
-+ return;
-+ }
-+
-+ /* Wait max 100 ms */
-+ wait_max = jiffies + msecs_to_jiffies(100);
-+ while (time_before(jiffies, wait_max)) {
-+ spin_unlock_irqrestore(&host->lock, *irq_flags);
-+ usleep_range(1, 10);
-+ spin_lock_irqsave(&host->lock, *irq_flags);
-+ sdcmd = bcm2835_sdhost_read(host, SDCMD);
-+ if (!(sdcmd & SDCMD_NEW_FLAG) ||
-+ (sdcmd & SDCMD_FAIL_FLAG))
-+ break;
-+ }
-+ }
-
-- if (timeout == 0) {
-+ /* Check for errors */
-+ if (sdcmd & SDCMD_NEW_FLAG) {
- pr_err("%s: command never completed.\n",
- mmc_hostname(host->mmc));
- bcm2835_sdhost_dumpregs(host);
- host->cmd->error = -EIO;
- tasklet_schedule(&host->finish_tasklet);
- return;
-- }
--
-- if (host->flush_fifo) {
-- for (timeout = 100;
-- (bcm2835_sdhost_read(host, SDHSTS) & SDHSTS_DATA_FLAG) && timeout;
-- timeout--) {
-- (void)bcm2835_sdhost_read(host, SDDATA);
-- }
-- host->flush_fifo = 0;
-- if (timeout == 0) {
-- pr_err("%s: FIFO never drained.\n",
-- mmc_hostname(host->mmc));
-- bcm2835_sdhost_dumpregs(host);
-- host->cmd->error = -EIO;
-- tasklet_schedule(&host->finish_tasklet);
-- return;
-- }
-- }
--
-- /* Check for errors */
-- if (sdcmd & SDCMD_FAIL_FLAG)
-- {
-+ } else if (sdcmd & SDCMD_FAIL_FLAG) {
- u32 sdhsts = bcm2835_sdhost_read(host, SDHSTS);
-
-+ /* Clear the errors */
-+ bcm2835_sdhost_write(host, SDHSTS_ERROR_MASK, SDHSTS);
-+
- if (host->debug)
- pr_info("%s: error detected - CMD %x, HSTS %03x, EDM %x\n",
- mmc_hostname(host->mmc), sdcmd, sdhsts,
-@@ -1003,7 +1197,7 @@ static void bcm2835_sdhost_finish_comman
- mmc_hostname(host->mmc),
- host->cmd->opcode);
- bcm2835_sdhost_dumpregs(host);
-- host->cmd->error = -EIO;
-+ host->cmd->error = -EILSEQ;
- }
- tasklet_schedule(&host->finish_tasklet);
- return;
-@@ -1018,31 +1212,31 @@ static void bcm2835_sdhost_finish_comman
- pr_debug("%s: finish_command %08x %08x %08x %08x\n",
- mmc_hostname(host->mmc),
- host->cmd->resp[0], host->cmd->resp[1], host->cmd->resp[2], host->cmd->resp[3]);
-+ log_event("RSP ", host->cmd->resp[0], host->cmd->resp[1]);
- } else {
- host->cmd->resp[0] = bcm2835_sdhost_read(host, SDRSP0);
- pr_debug("%s: finish_command %08x\n",
- mmc_hostname(host->mmc),
- host->cmd->resp[0]);
-+ log_event("RSP ", host->cmd->resp[0], 0);
- }
- }
-
-- host->cmd->error = 0;
--
- if (host->cmd == host->mrq->sbc) {
- /* Finished CMD23, now send actual command. */
- host->cmd = NULL;
-- bcm2835_sdhost_send_command(host, host->mrq->cmd);
-+ if (bcm2835_sdhost_send_command(host, host->mrq->cmd)) {
-+ if (host->data && host->dma_desc)
-+ /* DMA transfer starts now, PIO starts after irq */
-+ bcm2835_sdhost_start_dma(host);
-
-- if (host->cmd->data && host->use_dma)
-- /* DMA transfer starts now, PIO starts after irq */
-- bcm2835_sdhost_transfer_dma(host);
--
-- if (!host->use_busy)
-- bcm2835_sdhost_finish_command(host);
-- } else if (host->cmd == host->mrq->stop)
-+ if (!host->use_busy)
-+ bcm2835_sdhost_finish_command(host, NULL);
-+ }
-+ } else if (host->cmd == host->mrq->stop) {
- /* Finished CMD12 */
- tasklet_schedule(&host->finish_tasklet);
-- else {
-+ } else {
- /* Processed actual command. */
- host->cmd = NULL;
- if (!host->data)
-@@ -1050,6 +1244,7 @@ static void bcm2835_sdhost_finish_comman
- else if (host->data_complete)
- bcm2835_sdhost_transfer_complete(host);
- }
-+ log_event("FCM>", (u32)host->mrq, (u32)host->cmd);
- }
-
- static void bcm2835_sdhost_timeout(unsigned long data)
-@@ -1060,10 +1255,12 @@ static void bcm2835_sdhost_timeout(unsig
- host = (struct bcm2835_host *)data;
-
- spin_lock_irqsave(&host->lock, flags);
-+ log_event("TIM<", 0, 0);
-
- if (host->mrq) {
- pr_err("%s: timeout waiting for hardware interrupt.\n",
- mmc_hostname(host->mmc));
-+ log_dump();
- bcm2835_sdhost_dumpregs(host);
-
- if (host->data) {
-@@ -1084,74 +1281,15 @@ static void bcm2835_sdhost_timeout(unsig
- spin_unlock_irqrestore(&host->lock, flags);
- }
-
--static void bcm2835_sdhost_pio_timeout(unsigned long data)
--{
-- struct bcm2835_host *host;
-- unsigned long flags;
--
-- host = (struct bcm2835_host *)data;
--
-- spin_lock_irqsave(&host->lock, flags);
--
-- if (host->data) {
-- u32 sdhsts = bcm2835_sdhost_read(host, SDHSTS);
--
-- if (sdhsts & SDHSTS_REW_TIME_OUT) {
-- pr_err("%s: transfer timeout\n",
-- mmc_hostname(host->mmc));
-- if (host->debug)
-- bcm2835_sdhost_dumpregs(host);
-- } else {
-- pr_err("%s: unexpected transfer timeout\n",
-- mmc_hostname(host->mmc));
-- bcm2835_sdhost_dumpregs(host);
-- }
--
-- bcm2835_sdhost_write(host, SDHSTS_TRANSFER_ERROR_MASK,
-- SDHSTS);
--
-- host->data->error = -ETIMEDOUT;
--
-- bcm2835_sdhost_finish_data(host);
-- }
--
-- mmiowb();
-- spin_unlock_irqrestore(&host->lock, flags);
--}
--
--static void bcm2835_sdhost_enable_sdio_irq_nolock(struct bcm2835_host *host, int enable)
--{
-- if (enable)
-- host->hcfg |= SDHCFG_SDIO_IRPT_EN;
-- else
-- host->hcfg &= ~SDHCFG_SDIO_IRPT_EN;
-- bcm2835_sdhost_write(host, host->hcfg, SDHCFG);
-- mmiowb();
--}
--
--static void bcm2835_sdhost_enable_sdio_irq(struct mmc_host *mmc, int enable)
--{
-- struct bcm2835_host *host = mmc_priv(mmc);
-- unsigned long flags;
--
-- pr_debug("%s: enable_sdio_irq(%d)\n", mmc_hostname(mmc), enable);
-- spin_lock_irqsave(&host->lock, flags);
-- bcm2835_sdhost_enable_sdio_irq_nolock(host, enable);
-- spin_unlock_irqrestore(&host->lock, flags);
--}
--
--static u32 bcm2835_sdhost_busy_irq(struct bcm2835_host *host, u32 intmask)
-+static void bcm2835_sdhost_busy_irq(struct bcm2835_host *host, u32 intmask)
- {
-- const u32 handled = (SDHSTS_REW_TIME_OUT | SDHSTS_CMD_TIME_OUT |
-- SDHSTS_CRC16_ERROR | SDHSTS_CRC7_ERROR |
-- SDHSTS_FIFO_ERROR);
--
-+ log_event("IRQB", (u32)host->cmd, intmask);
- if (!host->cmd) {
- pr_err("%s: got command busy interrupt 0x%08x even "
- "though no command operation was in progress.\n",
- mmc_hostname(host->mmc), (unsigned)intmask);
- bcm2835_sdhost_dumpregs(host);
-- return 0;
-+ return;
- }
-
- if (!host->use_busy) {
-@@ -1159,7 +1297,7 @@ static u32 bcm2835_sdhost_busy_irq(struc
- "though not expecting one.\n",
- mmc_hostname(host->mmc), (unsigned)intmask);
- bcm2835_sdhost_dumpregs(host);
-- return 0;
-+ return;
- }
- host->use_busy = 0;
-
-@@ -1182,28 +1320,23 @@ static u32 bcm2835_sdhost_busy_irq(struc
- } else if (intmask & SDHSTS_CMD_TIME_OUT)
- host->cmd->error = -ETIMEDOUT;
-
-+ log_dump();
- bcm2835_sdhost_dumpregs(host);
-- tasklet_schedule(&host->finish_tasklet);
- }
- else
-- bcm2835_sdhost_finish_command(host);
--
-- return handled;
-+ bcm2835_sdhost_finish_command(host, NULL);
- }
-
--static u32 bcm2835_sdhost_data_irq(struct bcm2835_host *host, u32 intmask)
-+static void bcm2835_sdhost_data_irq(struct bcm2835_host *host, u32 intmask)
- {
-- const u32 handled = (SDHSTS_REW_TIME_OUT |
-- SDHSTS_CRC16_ERROR |
-- SDHSTS_FIFO_ERROR);
--
- /* There are no dedicated data/space available interrupt
- status bits, so it is necessary to use the single shared
- data/space available FIFO status bits. It is therefore not
- an error to get here when there is no data transfer in
- progress. */
-+ log_event("IRQD", (u32)host->data, intmask);
- if (!host->data)
-- return 0;
-+ return;
-
- if (intmask & (SDHSTS_CRC16_ERROR |
- SDHSTS_FIFO_ERROR |
-@@ -1214,46 +1347,37 @@ static u32 bcm2835_sdhost_data_irq(struc
- else
- host->data->error = -ETIMEDOUT;
-
-- bcm2835_sdhost_dumpregs(host);
-- tasklet_schedule(&host->finish_tasklet);
-- return handled;
-+ if (host->debug) {
-+ log_dump();
-+ bcm2835_sdhost_dumpregs(host);
-+ }
- }
-
-- /* Use the block interrupt for writes after the first block */
-- if (host->data->flags & MMC_DATA_WRITE) {
-+ if (host->data->error) {
-+ bcm2835_sdhost_finish_data(host);
-+ } else if (host->data->flags & MMC_DATA_WRITE) {
-+ /* Use the block interrupt for writes after the first block */
- host->hcfg &= ~(SDHCFG_DATA_IRPT_EN);
- host->hcfg |= SDHCFG_BLOCK_IRPT_EN;
- bcm2835_sdhost_write(host, host->hcfg, SDHCFG);
-- if (host->data->error)
-- bcm2835_sdhost_finish_data(host);
-- else
-- bcm2835_sdhost_transfer_pio(host);
-+ bcm2835_sdhost_transfer_pio(host);
- } else {
-- if (!host->data->error) {
-- bcm2835_sdhost_transfer_pio(host);
-- host->blocks--;
-- }
-+ bcm2835_sdhost_transfer_pio(host);
-+ host->blocks--;
- if ((host->blocks == 0) || host->data->error)
- bcm2835_sdhost_finish_data(host);
- }
--
-- return handled;
- }
-
--static u32 bcm2835_sdhost_block_irq(struct bcm2835_host *host, u32 intmask)
-+static void bcm2835_sdhost_block_irq(struct bcm2835_host *host, u32 intmask)
- {
-- struct dma_chan *dma_chan;
-- u32 dir_data;
-- const u32 handled = (SDHSTS_REW_TIME_OUT |
-- SDHSTS_CRC16_ERROR |
-- SDHSTS_FIFO_ERROR);
--
-+ log_event("IRQK", (u32)host->data, intmask);
- if (!host->data) {
- pr_err("%s: got block interrupt 0x%08x even "
- "though no data operation was in progress.\n",
- mmc_hostname(host->mmc), (unsigned)intmask);
- bcm2835_sdhost_dumpregs(host);
-- return handled;
-+ return;
- }
-
- if (intmask & (SDHSTS_CRC16_ERROR |
-@@ -1265,149 +1389,69 @@ static u32 bcm2835_sdhost_block_irq(stru
- else
- host->data->error = -ETIMEDOUT;
-
-- if (host->debug)
-+ if (host->debug) {
-+ log_dump();
- bcm2835_sdhost_dumpregs(host);
-- tasklet_schedule(&host->finish_tasklet);
-- return handled;
-+ }
- }
-
-- if (!host->use_dma) {
-+ if (!host->dma_desc) {
- BUG_ON(!host->blocks);
-- host->blocks--;
-- if ((host->blocks == 0) || host->data->error) {
-- /* Cancel the timer */
-- del_timer(&host->pio_timer);
--
-+ if (host->data->error || (--host->blocks == 0)) {
- bcm2835_sdhost_finish_data(host);
- } else {
-- /* Reset the timer */
-- mod_timer(&host->pio_timer,
-- jiffies + host->pio_timeout);
--
- bcm2835_sdhost_transfer_pio(host);
--
-- /* Reset the timer */
-- mod_timer(&host->pio_timer,
-- jiffies + host->pio_timeout);
- }
- } else if (host->data->flags & MMC_DATA_WRITE) {
-- dma_chan = host->dma_chan_tx;
-- dir_data = DMA_TO_DEVICE;
-- dma_unmap_sg(dma_chan->device->dev,
-- host->data->sg, host->data->sg_len,
-- dir_data);
--
- bcm2835_sdhost_finish_data(host);
- }
--
-- return handled;
- }
-
--
- static irqreturn_t bcm2835_sdhost_irq(int irq, void *dev_id)
- {
- irqreturn_t result = IRQ_NONE;
- struct bcm2835_host *host = dev_id;
-- u32 unexpected = 0, early = 0;
-- int loops = 0;
-+ u32 intmask;
-
- spin_lock(&host->lock);
-
-- for (loops = 0; loops < 1; loops++) {
-- u32 intmask, handled;
--
-- intmask = bcm2835_sdhost_read(host, SDHSTS);
-- handled = intmask & (SDHSTS_BUSY_IRPT |
-- SDHSTS_BLOCK_IRPT |
-- SDHSTS_SDIO_IRPT |
-- SDHSTS_DATA_FLAG);
-- if ((handled == SDHSTS_DATA_FLAG) &&
-- (loops == 0) && !host->data) {
-- pr_err("%s: sdhost_irq data interrupt 0x%08x even "
-- "though no data operation was in progress.\n",
-- mmc_hostname(host->mmc),
-- (unsigned)intmask);
--
-- bcm2835_sdhost_dumpregs(host);
-- }
--
-- if (!handled)
-- break;
-+ intmask = bcm2835_sdhost_read(host, SDHSTS);
-+ log_event("IRQ<", intmask, 0);
-
-- if (loops)
-- early |= handled;
-+ bcm2835_sdhost_write(host,
-+ SDHSTS_BUSY_IRPT |
-+ SDHSTS_BLOCK_IRPT |
-+ SDHSTS_SDIO_IRPT |
-+ SDHSTS_DATA_FLAG,
-+ SDHSTS);
-
-+ if (intmask & SDHSTS_BLOCK_IRPT) {
-+ bcm2835_sdhost_block_irq(host, intmask);
- result = IRQ_HANDLED;
-+ }
-
-- /* Clear all interrupts and notifications */
-- bcm2835_sdhost_write(host, intmask, SDHSTS);
--
-- if (intmask & SDHSTS_BUSY_IRPT)
-- handled |= bcm2835_sdhost_busy_irq(host, intmask);
--
-- /* There is no true data interrupt status bit, so it is
-- necessary to qualify the data flag with the interrupt
-- enable bit */
-- if ((intmask & SDHSTS_DATA_FLAG) &&
-- (host->hcfg & SDHCFG_DATA_IRPT_EN))
-- handled |= bcm2835_sdhost_data_irq(host, intmask);
--
-- if (intmask & SDHSTS_BLOCK_IRPT)
-- handled |= bcm2835_sdhost_block_irq(host, intmask);
--
-- if (intmask & SDHSTS_SDIO_IRPT) {
-- bcm2835_sdhost_enable_sdio_irq_nolock(host, false);
-- host->thread_isr |= SDHSTS_SDIO_IRPT;
-- result = IRQ_WAKE_THREAD;
-- }
-+ if (intmask & SDHSTS_BUSY_IRPT) {
-+ bcm2835_sdhost_busy_irq(host, intmask);
-+ result = IRQ_HANDLED;
-+ }
-
-- unexpected |= (intmask & ~handled);
-+ /* There is no true data interrupt status bit, so it is
-+ necessary to qualify the data flag with the interrupt
-+ enable bit */
-+ if ((intmask & SDHSTS_DATA_FLAG) &&
-+ (host->hcfg & SDHCFG_DATA_IRPT_EN)) {
-+ bcm2835_sdhost_data_irq(host, intmask);
-+ result = IRQ_HANDLED;
- }
-
- mmiowb();
-
-+ log_event("IRQ>", bcm2835_sdhost_read(host, SDHSTS), 0);
- spin_unlock(&host->lock);
-
-- if (early)
-- pr_debug("%s: early %x (loops %d)\n",
-- mmc_hostname(host->mmc), early, loops);
--
-- if (unexpected) {
-- pr_err("%s: unexpected interrupt 0x%08x.\n",
-- mmc_hostname(host->mmc), unexpected);
-- bcm2835_sdhost_dumpregs(host);
-- }
--
- return result;
- }
-
--static irqreturn_t bcm2835_sdhost_thread_irq(int irq, void *dev_id)
--{
-- struct bcm2835_host *host = dev_id;
-- unsigned long flags;
-- u32 isr;
--
-- spin_lock_irqsave(&host->lock, flags);
-- isr = host->thread_isr;
-- host->thread_isr = 0;
-- spin_unlock_irqrestore(&host->lock, flags);
--
-- if (isr & SDHSTS_SDIO_IRPT) {
-- sdio_run_irqs(host->mmc);
--
--/* Is this necessary? Why re-enable an interrupt which is enabled?
-- spin_lock_irqsave(&host->lock, flags);
-- if (host->flags & SDHSTS_SDIO_IRPT_ENABLED)
-- bcm2835_sdhost_enable_sdio_irq_nolock(host, true);
-- spin_unlock_irqrestore(&host->lock, flags);
--*/
-- }
--
-- return isr ? IRQ_HANDLED : IRQ_NONE;
--}
--
--
--
- void bcm2835_sdhost_set_clock(struct bcm2835_host *host, unsigned int clock)
- {
- int div = 0; /* Initialized for compiler warning */
-@@ -1417,9 +1461,8 @@ void bcm2835_sdhost_set_clock(struct bcm
- pr_info("%s: set_clock(%d)\n", mmc_hostname(host->mmc), clock);
-
- if ((host->overclock_50 > 50) &&
-- (clock == 50*MHZ)) {
-+ (clock == 50*MHZ))
- clock = host->overclock_50 * MHZ + (MHZ - 1);
-- }
-
- /* The SDCDIV register has 11 bits, and holds (div - 2).
- But in data mode the max is 50MHz wihout a minimum, and only the
-@@ -1466,6 +1509,11 @@ void bcm2835_sdhost_set_clock(struct bcm
- clock = host->max_clk / (div + 2);
- host->mmc->actual_clock = clock;
-
-+ /* Calibrate some delays */
-+
-+ host->ns_per_fifo_word = (1000000000/clock) *
-+ ((host->mmc->caps & MMC_CAP_4_BIT_DATA) ? 8 : 32);
-+
- if (clock > input_clock) {
- /* Save the closest value, to make it easier
- to reduce in the event of error */
-@@ -1501,6 +1549,7 @@ static void bcm2835_sdhost_request(struc
- {
- struct bcm2835_host *host;
- unsigned long flags;
-+ u32 edm, fsm;
-
- host = mmc_priv(mmc);
-
-@@ -1521,6 +1570,8 @@ static void bcm2835_sdhost_request(struc
- }
-
- /* Reset the error statuses in case this is a retry */
-+ if (mrq->sbc)
-+ mrq->sbc->error = 0;
- if (mrq->cmd)
- mrq->cmd->error = 0;
- if (mrq->data)
-@@ -1536,28 +1587,58 @@ static void bcm2835_sdhost_request(struc
- return;
- }
-
-+ if (host->use_dma && mrq->data &&
-+ (mrq->data->blocks > host->pio_limit))
-+ bcm2835_sdhost_prepare_dma(host, mrq->data);
-+
- spin_lock_irqsave(&host->lock, flags);
-
- WARN_ON(host->mrq != NULL);
--
- host->mrq = mrq;
-
-- if (mrq->sbc)
-- bcm2835_sdhost_send_command(host, mrq->sbc);
-- else
-- bcm2835_sdhost_send_command(host, mrq->cmd);
-+ edm = bcm2835_sdhost_read(host, SDEDM);
-+ fsm = edm & SDEDM_FSM_MASK;
-
-- mmiowb();
-- spin_unlock_irqrestore(&host->lock, flags);
-+ log_event("REQ<", (u32)mrq, edm);
-+ if ((fsm != SDEDM_FSM_IDENTMODE) &&
-+ (fsm != SDEDM_FSM_DATAMODE)) {
-+ pr_err("%s: previous command (%d) not complete (EDM %x)\n",
-+ mmc_hostname(host->mmc),
-+ bcm2835_sdhost_read(host, SDCMD) & SDCMD_CMD_MASK,
-+ edm);
-+ log_event("REQ!", (u32)mrq, edm);
-+ log_dump();
-+ bcm2835_sdhost_dumpregs(host);
-+ mrq->cmd->error = -EILSEQ;
-+ tasklet_schedule(&host->finish_tasklet);
-+ mmiowb();
-+ spin_unlock_irqrestore(&host->lock, flags);
-+ return;
-+ }
-+
-+ host->use_sbc = !!mrq->sbc &&
-+ (host->mrq->data->flags & USE_CMD23_FLAGS);
-+ if (host->use_sbc) {
-+ if (bcm2835_sdhost_send_command(host, mrq->sbc)) {
-+ if (!host->use_busy)
-+ bcm2835_sdhost_finish_command(host, &flags);
-+ }
-+ } else if (bcm2835_sdhost_send_command(host, mrq->cmd)) {
-+ if (host->data && host->dma_desc)
-+ /* DMA transfer starts now, PIO starts after irq */
-+ bcm2835_sdhost_start_dma(host);
-
-- if (!mrq->sbc && mrq->cmd->data && host->use_dma)
-- /* DMA transfer starts now, PIO starts after irq */
-- bcm2835_sdhost_transfer_dma(host);
-+ if (!host->use_busy)
-+ bcm2835_sdhost_finish_command(host, &flags);
-+ }
-
-- if (!host->use_busy)
-- bcm2835_sdhost_finish_command(host);
--}
-+ log_event("CMD ", (u32)mrq->cmd->opcode,
-+ mrq->data ? (u32)mrq->data->blksz : 0);
-+ mmiowb();
-
-+ log_event("REQ>", (u32)mrq, 0);
-+ spin_unlock_irqrestore(&host->lock, flags);
-+}
-
- static void bcm2835_sdhost_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
- {
-@@ -1574,6 +1655,8 @@ static void bcm2835_sdhost_set_ios(struc
-
- spin_lock_irqsave(&host->lock, flags);
-
-+ log_event("IOS<", ios->clock, 0);
-+
- if (!ios->clock || ios->clock != host->clock) {
- bcm2835_sdhost_set_clock(host, ios->clock);
- host->clock = ios->clock;
-@@ -1596,59 +1679,53 @@ static void bcm2835_sdhost_set_ios(struc
- spin_unlock_irqrestore(&host->lock, flags);
- }
-
--static int bcm2835_sdhost_multi_io_quirk(struct mmc_card *card,
-- unsigned int direction,
-- u32 blk_pos, int blk_size)
--{
-- /* There is a bug in the host controller hardware that makes
-- reading the final sector of the card as part of a multiple read
-- problematic. Detect that case and shorten the read accordingly.
-- */
-+static struct mmc_host_ops bcm2835_sdhost_ops = {
-+ .request = bcm2835_sdhost_request,
-+ .set_ios = bcm2835_sdhost_set_ios,
-+ .hw_reset = bcm2835_sdhost_reset,
-+};
-+
-+static void bcm2835_sdhost_cmd_wait_work(struct work_struct *work)
-+{
- struct bcm2835_host *host;
-+ unsigned long flags;
-
-- host = mmc_priv(card->host);
-+ host = container_of(work, struct bcm2835_host, cmd_wait_wq);
-
-- if (!host->sectors) {
-- /* csd.capacity is in weird units - convert to sectors */
-- u32 card_sectors = (card->csd.capacity << (card->csd.read_blkbits - 9));
-- if ((direction == MMC_DATA_READ) &&
-- ((blk_pos + blk_size) == card_sectors))
-- blk_size--;
-- return blk_size;
-- }
-+ spin_lock_irqsave(&host->lock, flags);
-
-- if (direction == MMC_DATA_READ) {
-- int i;
-- int sector;
-- for (i = 0; blk_pos > (sector = host->single_read_sectors[i]); i++)
-- continue;
-+ log_event("CWK<", (u32)host->cmd, (u32)host->mrq);
-
-- if ((blk_pos + blk_size) > sector)
-- blk_size = (blk_pos == sector) ? 1 : (sector - blk_pos);
-+ /*
-+ * If this tasklet gets rescheduled while running, it will
-+ * be run again afterwards but without any active request.
-+ */
-+ if (!host->mrq) {
-+ spin_unlock_irqrestore(&host->lock, flags);
-+ return;
- }
-- return blk_size;
--}
-
-+ bcm2835_sdhost_finish_command(host, &flags);
-
--static struct mmc_host_ops bcm2835_sdhost_ops = {
-- .request = bcm2835_sdhost_request,
-- .set_ios = bcm2835_sdhost_set_ios,
-- .enable_sdio_irq = bcm2835_sdhost_enable_sdio_irq,
-- .hw_reset = bcm2835_sdhost_reset,
-- .multi_io_quirk = bcm2835_sdhost_multi_io_quirk,
--};
-+ mmiowb();
-+
-+ log_event("CWK>", (u32)host->cmd, 0);
-
-+ spin_unlock_irqrestore(&host->lock, flags);
-+}
-
- static void bcm2835_sdhost_tasklet_finish(unsigned long param)
- {
- struct bcm2835_host *host;
- unsigned long flags;
- struct mmc_request *mrq;
-+ struct dma_chan *terminate_chan = NULL;
-
- host = (struct bcm2835_host *)param;
-
- spin_lock_irqsave(&host->lock, flags);
-
-+ log_event("TSK<", (u32)host->mrq, 0);
- /*
- * If this tasklet gets rescheduled while running, it will
- * be run again afterwards but without any active request.
-@@ -1683,11 +1760,23 @@ static void bcm2835_sdhost_tasklet_finis
-
- mmiowb();
-
-+ host->dma_desc = NULL;
-+ terminate_chan = host->dma_chan;
-+ host->dma_chan = NULL;
-+
- spin_unlock_irqrestore(&host->lock, flags);
-- mmc_request_done(host->mmc, mrq);
--}
-
-+ if (terminate_chan)
-+ {
-+ int err = dmaengine_terminate_all(terminate_chan);
-+ if (err)
-+ pr_err("%s: failed to terminate DMA (%d)\n",
-+ mmc_hostname(host->mmc), err);
-+ }
-
-+ mmc_request_done(host->mmc, mrq);
-+ log_event("TSK>", (u32)mrq, 0);
-+}
-
- int bcm2835_sdhost_add_host(struct bcm2835_host *host)
- {
-@@ -1709,10 +1798,10 @@ int bcm2835_sdhost_add_host(struct bcm28
- mmc->f_max, mmc->f_min, mmc->max_busy_timeout);
-
- /* host controller capabilities */
-- mmc->caps |= /* MMC_CAP_SDIO_IRQ |*/ MMC_CAP_4_BIT_DATA |
-+ mmc->caps |=
- MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED |
- MMC_CAP_NEEDS_POLL | MMC_CAP_HW_RESET | MMC_CAP_ERASE |
-- (ALLOW_CMD23 * MMC_CAP_CMD23);
-+ ((ALLOW_CMD23_READ|ALLOW_CMD23_WRITE) * MMC_CAP_CMD23);
-
- spin_lock_init(&host->lock);
-
-@@ -1722,9 +1811,9 @@ int bcm2835_sdhost_add_host(struct bcm28
- pr_err("%s: unable to initialise DMA channels. "
- "Falling back to PIO\n",
- mmc_hostname(mmc));
-- host->have_dma = false;
-+ host->use_dma = false;
- } else {
-- host->have_dma = true;
-+ host->use_dma = true;
-
- cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
- cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
-@@ -1741,7 +1830,7 @@ int bcm2835_sdhost_add_host(struct bcm28
- ret = dmaengine_slave_config(host->dma_chan_rx, &cfg);
- }
- } else {
-- host->have_dma = false;
-+ host->use_dma = false;
- }
-
- mmc->max_segs = 128;
-@@ -1756,16 +1845,15 @@ int bcm2835_sdhost_add_host(struct bcm28
- tasklet_init(&host->finish_tasklet,
- bcm2835_sdhost_tasklet_finish, (unsigned long)host);
-
-- setup_timer(&host->timer, bcm2835_sdhost_timeout,
-- (unsigned long)host);
-+ INIT_WORK(&host->cmd_wait_wq, bcm2835_sdhost_cmd_wait_work);
-
-- setup_timer(&host->pio_timer, bcm2835_sdhost_pio_timeout,
-+ setup_timer(&host->timer, bcm2835_sdhost_timeout,
- (unsigned long)host);
-
- bcm2835_sdhost_init(host, 0);
-- ret = request_threaded_irq(host->irq, bcm2835_sdhost_irq,
-- bcm2835_sdhost_thread_irq,
-- IRQF_SHARED, mmc_hostname(mmc), host);
-+
-+ ret = request_irq(host->irq, bcm2835_sdhost_irq, 0 /*IRQF_SHARED*/,
-+ mmc_hostname(mmc), host);
- if (ret) {
- pr_err("%s: failed to request IRQ %d: %d\n",
- mmc_hostname(mmc), host->irq, ret);
-@@ -1776,11 +1864,11 @@ int bcm2835_sdhost_add_host(struct bcm28
- mmc_add_host(mmc);
-
- pio_limit_string[0] = '\0';
-- if (host->have_dma && (host->pio_limit > 0))
-+ if (host->use_dma && (host->pio_limit > 0))
- sprintf(pio_limit_string, " (>%d)", host->pio_limit);
- pr_info("%s: %s loaded - DMA %s%s\n",
- mmc_hostname(mmc), DRIVER_NAME,
-- host->have_dma ? "enabled" : "disabled",
-+ host->use_dma ? "enabled" : "disabled",
- pio_limit_string);
-
- return 0;
-@@ -1810,8 +1898,11 @@ static int bcm2835_sdhost_probe(struct p
- mmc->ops = &bcm2835_sdhost_ops;
- host = mmc_priv(mmc);
- host->mmc = mmc;
-+ host->cmd_quick_poll_retries = 0;
- host->pio_timeout = msecs_to_jiffies(500);
-+ host->pio_limit = 1;
- host->max_delay = 1; /* Warn if over 1ms */
-+ host->allow_dma = 1;
- spin_lock_init(&host->lock);
-
- iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-@@ -1827,13 +1918,12 @@ static int bcm2835_sdhost_probe(struct p
- return -ENODEV;
- }
- host->bus_addr = be32_to_cpup(addr);
-+ log_init(iomem->start - host->bus_addr);
- pr_debug(" - ioaddr %lx, iomem->start %lx, bus_addr %lx\n",
- (unsigned long)host->ioaddr,
- (unsigned long)iomem->start,
- (unsigned long)host->bus_addr);
-
-- host->allow_dma = ALLOW_DMA;
--
- if (node) {
- /* Read any custom properties */
- of_property_read_u32(node,
-@@ -1845,16 +1935,17 @@ static int bcm2835_sdhost_probe(struct p
- of_property_read_u32(node,
- "brcm,pio-limit",
- &host->pio_limit);
-- host->allow_dma = ALLOW_DMA &&
-+ host->allow_dma =
- !of_property_read_bool(node, "brcm,force-pio");
- host->debug = of_property_read_bool(node, "brcm,debug");
-- of_property_read_u32(node,
-- "brcm,debug-flags",
-- &host->debug_flags);
- }
-
-- if (host->debug_flags)
-- dev_err(dev, "debug_flags=%x\n", host->debug_flags);
-+ host->dma_chan = NULL;
-+ host->dma_desc = NULL;
-+
-+ /* Formally recognise the other way of disabling DMA */
-+ if (host->pio_limit == 0x7fffffff)
-+ host->allow_dma = false;
-
- if (host->allow_dma) {
- if (node) {
-@@ -1940,15 +2031,12 @@ static int bcm2835_sdhost_remove(struct
- return 0;
- }
-
--
- static const struct of_device_id bcm2835_sdhost_match[] = {
- { .compatible = "brcm,bcm2835-sdhost" },
- { }
- };
- MODULE_DEVICE_TABLE(of, bcm2835_sdhost_match);
-
--
--
- static struct platform_driver bcm2835_sdhost_driver = {
- .probe = bcm2835_sdhost_probe,
- .remove = bcm2835_sdhost_remove,
diff --git a/target/linux/brcm2708/patches-4.4/0144-BCM270X_DT-Add-dtparams-for-the-SD-interface.patch b/target/linux/brcm2708/patches-4.4/0144-BCM270X_DT-Add-dtparams-for-the-SD-interface.patch
deleted file mode 100644
index dbf1b4b..0000000
--- a/target/linux/brcm2708/patches-4.4/0144-BCM270X_DT-Add-dtparams-for-the-SD-interface.patch
+++ /dev/null
@@ -1,235 +0,0 @@
-From 04d6a3c61ec9d05399a49007f3564a57b91355dd Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 12 Feb 2016 15:38:00 +0000
-Subject: [PATCH] BCM270X_DT: Add dtparams for the SD interface
-
-Add new base dtparams sd_overclock, sd_force_pio, sd_pio_limit
-and sd_debug.
----
- arch/arm/boot/dts/bcm2708-rpi-b-plus.dts | 4 ++++
- arch/arm/boot/dts/bcm2708-rpi-b.dts | 4 ++++
- arch/arm/boot/dts/bcm2708-rpi-cm.dts | 1 -
- arch/arm/boot/dts/bcm2708-rpi-cm.dtsi | 13 +++++++++++++
- arch/arm/boot/dts/bcm2708_common.dtsi | 2 ++
- arch/arm/boot/dts/bcm2709-rpi-2-b.dts | 4 ++++
- arch/arm/boot/dts/overlays/README | 11 ++++++++++-
- arch/arm/boot/dts/overlays/mmc-overlay.dts | 1 -
- arch/arm/boot/dts/overlays/sdhost-overlay.dts | 27 +++++++++++++-------------
- arch/arm/boot/dts/overlays/sdtweak-overlay.dts | 14 ++++++-------
- 10 files changed, 58 insertions(+), 23 deletions(-)
-
---- a/arch/arm/boot/dts/bcm2708-rpi-b-plus.dts
-+++ b/arch/arm/boot/dts/bcm2708-rpi-b-plus.dts
-@@ -141,5 +141,9 @@
- audio = <&audio>,"status";
- watchdog = <&watchdog>,"status";
- random = <&random>,"status";
-+ sd_overclock = <&sdhost>,"brcm,overclock-50:0";
-+ sd_force_pio = <&sdhost>,"brcm,force-pio?";
-+ sd_pio_limit = <&sdhost>,"brcm,pio-limit:0";
-+ sd_debug = <&sdhost>,"brcm,debug";
- };
- };
---- a/arch/arm/boot/dts/bcm2708-rpi-b.dts
-+++ b/arch/arm/boot/dts/bcm2708-rpi-b.dts
-@@ -131,5 +131,9 @@
- audio = <&audio>,"status";
- watchdog = <&watchdog>,"status";
- random = <&random>,"status";
-+ sd_overclock = <&sdhost>,"brcm,overclock-50:0";
-+ sd_force_pio = <&sdhost>,"brcm,force-pio?";
-+ sd_pio_limit = <&sdhost>,"brcm,pio-limit:0";
-+ sd_debug = <&sdhost>,"brcm,debug";
- };
- };
---- a/arch/arm/boot/dts/bcm2708-rpi-cm.dts
-+++ b/arch/arm/boot/dts/bcm2708-rpi-cm.dts
-@@ -97,6 +97,5 @@
- i2c0_baudrate = <&i2c0>,"clock-frequency:0";
- i2c1_baudrate = <&i2c1>,"clock-frequency:0";
- i2c2_baudrate = <&i2c2>,"clock-frequency:0";
-- core_freq = <&clk_core>,"clock-frequency:0";
- };
- };
---- a/arch/arm/boot/dts/bcm2708-rpi-cm.dtsi
-+++ b/arch/arm/boot/dts/bcm2708-rpi-cm.dtsi
-@@ -7,6 +7,13 @@
- };
- };
-
-+&gpio {
-+ sdhost_pins: sdhost_pins {
-+ brcm,pins = <48 49 50 51 52 53>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+};
-+
- &leds {
- act_led: act {
- label = "led0";
-@@ -29,6 +36,8 @@
-
- / {
- __overrides__ {
-+ core_freq = <&clk_core>,"clock-frequency:0";
-+
- act_led_gpio = <&act_led>,"gpios:4";
- act_led_activelow = <&act_led>,"gpios:8";
- act_led_trigger = <&act_led>,"linux,default-trigger";
-@@ -36,5 +45,9 @@
- audio = <&audio>,"status";
- watchdog = <&watchdog>,"status";
- random = <&random>,"status";
-+ sd_overclock = <&sdhost>,"brcm,overclock-50:0";
-+ sd_force_pio = <&sdhost>,"brcm,force-pio?";
-+ sd_pio_limit = <&sdhost>,"brcm,pio-limit:0";
-+ sd_debug = <&sdhost>,"brcm,debug";
- };
- };
---- a/arch/arm/boot/dts/bcm2708_common.dtsi
-+++ b/arch/arm/boot/dts/bcm2708_common.dtsi
-@@ -135,6 +135,7 @@
- dmas = <&dma 13>,
- <&dma 13>;
- dma-names = "tx", "rx";
-+ brcm,overclock-50 = <0>;
- brcm,pio-limit = <1>;
- status = "disabled";
- };
-@@ -203,6 +204,7 @@
- dmas = <&dma 11>,
- <&dma 11>;
- dma-names = "tx", "rx";
-+ brcm,overclock-50 = <0>;
- status = "disabled";
- };
-
---- a/arch/arm/boot/dts/bcm2709-rpi-2-b.dts
-+++ b/arch/arm/boot/dts/bcm2709-rpi-2-b.dts
-@@ -141,5 +141,9 @@
- audio = <&audio>,"status";
- watchdog = <&watchdog>,"status";
- random = <&random>,"status";
-+ sd_overclock = <&sdhost>,"brcm,overclock-50:0";
-+ sd_force_pio = <&sdhost>,"brcm,force-pio?";
-+ sd_pio_limit = <&sdhost>,"brcm,pio-limit:0";
-+ sd_debug = <&sdhost>,"brcm,debug";
- };
- };
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -112,6 +112,16 @@ Params:
- random Set to "on" to enable the hardware random
- number generator (default "on")
-
-+ sd_overclock Clock (in MHz) to use when the MMC framework
-+ requests 50MHz
-+
-+ sd_force_pio Disable DMA support for SD driver (default off)
-+
-+ sd_pio_limit Number of blocks above which to use DMA for
-+ SD card (default 1)
-+
-+ sd_debug Enable debug output from SD driver (default off)
-+
- uart0 Set to "off" to disable uart0 (default "on")
-
- watchdog Set to "on" to enable the hardware watchdog
-@@ -443,7 +453,6 @@ Info: Selects the bcm2835-mmc SD/MMC d
- Load: dtoverlay=mmc,<param>=<val>
- Params: overclock_50 Clock (in MHz) to use when the MMC framework
- requests 50MHz
-- force_pio Disable DMA support
-
-
- Name: mz61581
---- a/arch/arm/boot/dts/overlays/mmc-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/mmc-overlay.dts
-@@ -34,6 +34,5 @@
-
- __overrides__ {
- overclock_50 = <&frag0>,"brcm,overclock-50:0";
-- force_pio = <&frag0>,"brcm,force-pio?";
- };
- };
---- a/arch/arm/boot/dts/overlays/sdhost-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/sdhost-overlay.dts
-@@ -1,19 +1,14 @@
- /dts-v1/;
- /plugin/;
-
-+/* Provide backwards compatible aliases for the old sdhost dtparams. */
-+
- /{
- compatible = "brcm,bcm2708";
-
- fragment at 0 {
-- target = <&mmc>;
-- __overlay__ {
-- status = "disabled";
-- };
-- };
--
-- fragment at 1 {
- target = <&sdhost>;
-- frag1: __overlay__ {
-+ frag0: __overlay__ {
- brcm,overclock-50 = <0>;
- brcm,pio-limit = <1>;
- brcm,debug-flags = <0>;
-@@ -21,11 +16,17 @@
- };
- };
-
-+ fragment at 1 {
-+ target = <&mmc>;
-+ __overlay__ {
-+ status = "disabled";
-+ };
-+ };
-+
- __overrides__ {
-- overclock_50 = <&frag1>,"brcm,overclock-50:0";
-- force_pio = <&frag1>,"brcm,force-pio?";
-- pio_limit = <&frag1>,"brcm,pio-limit:0";
-- debug = <&frag1>,"brcm,debug?";
-- debug_flags = <&frag1>,"brcm,debug-flags:0";
-+ overclock_50 = <&frag0>,"brcm,overclock-50:0";
-+ force_pio = <&frag0>,"brcm,force-pio?";
-+ pio_limit = <&frag0>,"brcm,pio-limit:0";
-+ debug = <&frag0>,"brcm,debug?";
- };
- };
---- a/arch/arm/boot/dts/overlays/sdtweak-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/sdtweak-overlay.dts
-@@ -1,23 +1,23 @@
- /dts-v1/;
- /plugin/;
-
-+/* Provide backwards compatible aliases for the old sdhost dtparams. */
-+
- /{
- compatible = "brcm,bcm2708";
-
- fragment at 0 {
- target = <&sdhost>;
-- frag1: __overlay__ {
-+ frag0: __overlay__ {
- brcm,overclock-50 = <0>;
- brcm,pio-limit = <1>;
-- brcm,debug-flags = <0>;
- };
- };
-
- __overrides__ {
-- overclock_50 = <&frag1>,"brcm,overclock-50:0";
-- force_pio = <&frag1>,"brcm,force-pio?";
-- pio_limit = <&frag1>,"brcm,pio-limit:0";
-- debug = <&frag1>,"brcm,debug?";
-- debug_flags = <&frag1>,"brcm,debug-flags:0";
-+ overclock_50 = <&frag0>,"brcm,overclock-50:0";
-+ force_pio = <&frag0>,"brcm,force-pio?";
-+ pio_limit = <&frag0>,"brcm,pio-limit:0";
-+ debug = <&frag0>,"brcm,debug?";
- };
- };
diff --git a/target/linux/brcm2708/patches-4.4/0145-dcw_otg-trim-xfer-length-when-buffer-larger-than-all.patch b/target/linux/brcm2708/patches-4.4/0145-dcw_otg-trim-xfer-length-when-buffer-larger-than-all.patch
deleted file mode 100644
index 8a3f405..0000000
--- a/target/linux/brcm2708/patches-4.4/0145-dcw_otg-trim-xfer-length-when-buffer-larger-than-all.patch
+++ /dev/null
@@ -1,37 +0,0 @@
-From 8cf8f0caacfc0ae3da52de8112b0e0b6cc42086b Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Fri, 12 Feb 2016 14:50:25 +0000
-Subject: [PATCH] dcw_otg: trim xfer length when buffer larger than allocated
- size is received
-
----
- drivers/usb/host/dwc_otg/dwc_otg_hcd_intr.c | 11 +++++++++++
- 1 file changed, 11 insertions(+)
-
---- a/drivers/usb/host/dwc_otg/dwc_otg_hcd_intr.c
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_hcd_intr.c
-@@ -737,6 +737,11 @@ static int update_urb_state_xfer_comp(dw
- DWC_OTG_HC_XFER_COMPLETE,
- &short_read);
-
-+ if (urb->actual_length + xfer_length > urb->length) {
-+ DWC_WARN("%s(): trimming xfer length\n", __func__);
-+ xfer_length = urb->length - urb->actual_length;
-+ }
-+
- /* non DWORD-aligned buffer case handling. */
- if (hc->align_buff && xfer_length && hc->ep_is_in) {
- dwc_memcpy(urb->buf + urb->actual_length, hc->qh->dw_align_buf,
-@@ -1423,6 +1428,12 @@ static void update_urb_state_xfer_intr(d
- {
- uint32_t bytes_transferred = get_actual_xfer_length(hc, hc_regs, qtd,
- halt_status, NULL);
-+
-+ if (urb->actual_length + bytes_transferred > urb->length) {
-+ DWC_WARN("%s(): trimming xfer length\n", __func__);
-+ bytes_transferred = urb->length - urb->actual_length;
-+ }
-+
- /* non DWORD-aligned buffer case handling. */
- if (hc->align_buff && bytes_transferred && hc->ep_is_in) {
- dwc_memcpy(urb->buf + urb->actual_length, hc->qh->dw_align_buf,
diff --git a/target/linux/brcm2708/patches-4.4/0146-bcm2835-sdhost-Restore-ATOMIC-flag-to-PIO-sg-mapping.patch b/target/linux/brcm2708/patches-4.4/0146-bcm2835-sdhost-Restore-ATOMIC-flag-to-PIO-sg-mapping.patch
deleted file mode 100644
index 7cdddf9..0000000
--- a/target/linux/brcm2708/patches-4.4/0146-bcm2835-sdhost-Restore-ATOMIC-flag-to-PIO-sg-mapping.patch
+++ /dev/null
@@ -1,32 +0,0 @@
-From 617f80917f4d8a50ce8ea1d4f4f9ac30866757b7 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 15 Feb 2016 10:00:27 +0000
-Subject: [PATCH] bcm2835-sdhost: Restore ATOMIC flag to PIO sg mapping
-
-Allocation problems have been seen in a wireless driver, and
-this is the only change which might have been responsible.
----
- drivers/mmc/host/bcm2835-sdhost.c | 7 +++----
- 1 file changed, 3 insertions(+), 4 deletions(-)
-
---- a/drivers/mmc/host/bcm2835-sdhost.c
-+++ b/drivers/mmc/host/bcm2835-sdhost.c
-@@ -874,15 +874,14 @@ static void bcm2835_sdhost_prepare_data(
- host->flush_fifo = 0;
- host->data->bytes_xfered = 0;
-
--
- if (!host->dma_desc) {
- /* Use PIO */
-- int flags;
-+ int flags = SG_MITER_ATOMIC;
-
- if (data->flags & MMC_DATA_READ)
-- flags = SG_MITER_TO_SG;
-+ flags |= SG_MITER_TO_SG;
- else
-- flags = SG_MITER_FROM_SG;
-+ flags |= SG_MITER_FROM_SG;
- sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags);
- host->blocks = data->blocks;
- }
diff --git a/target/linux/brcm2708/patches-4.4/0147-Updated-smsc95xx-driver-to-check-for-a-valid-MAC-add.patch b/target/linux/brcm2708/patches-4.4/0147-Updated-smsc95xx-driver-to-check-for-a-valid-MAC-add.patch
deleted file mode 100644
index 036c79e..0000000
--- a/target/linux/brcm2708/patches-4.4/0147-Updated-smsc95xx-driver-to-check-for-a-valid-MAC-add.patch
+++ /dev/null
@@ -1,39 +0,0 @@
-From a1285def32834713d38a8777969396046f2ce988 Mon Sep 17 00:00:00 2001
-From: Craig Roberts <cjr at craigroberts.net>
-Date: Tue, 16 Feb 2016 10:03:42 +0000
-Subject: [PATCH] Updated smsc95xx driver to check for a valid MAC address in
- eeprom before using smsc95xx.macaddr parameter passed on command line.
-
-The built-in RPi adaptor will still get a MAC address based on the parameter passed on the command line as the RPi hardware does not have an eeprom,
-however usb->ethernet adaptors using the same driver should have an eeprom with MAC address as part of their hardware and therefore will use this
-meaning they don't end up with the same MAC address as the built-in RPi adaptor.
----
- drivers/net/usb/smsc95xx.c | 10 +++++-----
- 1 file changed, 5 insertions(+), 5 deletions(-)
-
---- a/drivers/net/usb/smsc95xx.c
-+++ b/drivers/net/usb/smsc95xx.c
-@@ -817,10 +817,6 @@ static int smsc95xx_is_macaddr_param(str
-
- static void smsc95xx_init_mac_address(struct usbnet *dev)
- {
-- /* Check module parameters */
-- if (smsc95xx_is_macaddr_param(dev, dev->net->dev_addr))
-- return;
--
- /* try reading mac address from EEPROM */
- if (smsc95xx_read_eeprom(dev, EEPROM_MAC_OFFSET, ETH_ALEN,
- dev->net->dev_addr) == 0) {
-@@ -831,7 +827,11 @@ static void smsc95xx_init_mac_address(st
- }
- }
-
-- /* no eeprom, or eeprom values are invalid. generate random MAC */
-+ /* Check module parameters */
-+ if (smsc95xx_is_macaddr_param(dev, dev->net->dev_addr))
-+ return;
-+
-+ /* no eeprom, or eeprom values are invalid, and no module parameter specified to set MAC. Generate random MAC */
- eth_hw_addr_random(dev->net);
- netif_dbg(dev, ifup, dev->net, "MAC address set to eth_random_addr\n");
- }
diff --git a/target/linux/brcm2708/patches-4.4/0148-dcw_otg-Make-trimming-messages-less-noisy.patch b/target/linux/brcm2708/patches-4.4/0148-dcw_otg-Make-trimming-messages-less-noisy.patch
deleted file mode 100644
index bc1962d..0000000
--- a/target/linux/brcm2708/patches-4.4/0148-dcw_otg-Make-trimming-messages-less-noisy.patch
+++ /dev/null
@@ -1,31 +0,0 @@
-From f35eeb2263b45c800be90a6299a532be34ddeec9 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Wed, 17 Feb 2016 19:02:31 +0000
-Subject: [PATCH] dcw_otg: Make trimming messages less noisy
-
----
- drivers/usb/host/dwc_otg/dwc_otg_hcd_intr.c | 6 ++++--
- 1 file changed, 4 insertions(+), 2 deletions(-)
-
---- a/drivers/usb/host/dwc_otg/dwc_otg_hcd_intr.c
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_hcd_intr.c
-@@ -738,7 +738,8 @@ static int update_urb_state_xfer_comp(dw
- &short_read);
-
- if (urb->actual_length + xfer_length > urb->length) {
-- DWC_WARN("%s(): trimming xfer length\n", __func__);
-+ printk_once(KERN_DEBUG "dwc_otg: DEVICE:%03d : %s:%d:trimming xfer length\n",
-+ hc->dev_addr, __func__, __LINE__);
- xfer_length = urb->length - urb->actual_length;
- }
-
-@@ -1430,7 +1431,8 @@ static void update_urb_state_xfer_intr(d
- halt_status, NULL);
-
- if (urb->actual_length + bytes_transferred > urb->length) {
-- DWC_WARN("%s(): trimming xfer length\n", __func__);
-+ printk_once(KERN_DEBUG "dwc_otg: DEVICE:%03d : %s:%d:trimming xfer length\n",
-+ hc->dev_addr, __func__, __LINE__);
- bytes_transferred = urb->length - urb->actual_length;
- }
-
diff --git a/target/linux/brcm2708/patches-4.4/0149-BCM270X_DT-at86rf233-overlay-drop-to-3MHz.patch b/target/linux/brcm2708/patches-4.4/0149-BCM270X_DT-at86rf233-overlay-drop-to-3MHz.patch
deleted file mode 100644
index f0326ab..0000000
--- a/target/linux/brcm2708/patches-4.4/0149-BCM270X_DT-at86rf233-overlay-drop-to-3MHz.patch
+++ /dev/null
@@ -1,36 +0,0 @@
-From 02062281b451fd98412ed607e8d662c0a8d3c19d Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Thu, 18 Feb 2016 15:28:14 +0000
-Subject: [PATCH] BCM270X_DT: at86rf233 overlay - drop to 3MHz
-
-The consensus is that 6MHz is too fast, but that 3MHz is OK.
-
-See: https://github.com/raspberrypi/linux/issues/1294
- https://github.com/raspberrypi/linux/issues/1151
----
- arch/arm/boot/dts/overlays/README | 2 +-
- arch/arm/boot/dts/overlays/at86rf233-overlay.dts | 2 +-
- 2 files changed, 2 insertions(+), 2 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -188,7 +188,7 @@ Load: dtoverlay=at86rf233,<param>=<val
- Params: interrupt GPIO used for INT (default 23)
- reset GPIO used for Reset (default 24)
- sleep GPIO used for Sleep (default 25)
-- speed SPI bus speed in Hz (default 6000000)
-+ speed SPI bus speed in Hz (default 3000000)
- trim Fine tuning of the internal capacitance
- arrays (0=+0pF, 15=+4.5pF, default 15)
-
---- a/arch/arm/boot/dts/overlays/at86rf233-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/at86rf233-overlay.dts
-@@ -25,7 +25,7 @@
- interrupts = <23 4>; /* active high */
- reset-gpio = <&gpio 24 1>;
- sleep-gpio = <&gpio 25 1>;
-- spi-max-frequency = <6000000>;
-+ spi-max-frequency = <3000000>;
- xtal-trim = /bits/ 8 <0xf>;
- };
- };
diff --git a/target/linux/brcm2708/patches-4.4/0150-bcm2835-sdhost-Downgrade-log-message-status.patch b/target/linux/brcm2708/patches-4.4/0150-bcm2835-sdhost-Downgrade-log-message-status.patch
deleted file mode 100644
index 367130f..0000000
--- a/target/linux/brcm2708/patches-4.4/0150-bcm2835-sdhost-Downgrade-log-message-status.patch
+++ /dev/null
@@ -1,22 +0,0 @@
-From 42d750a9c671e6df0337dacf70990166d226c542 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 19 Feb 2016 12:04:48 +0000
-Subject: [PATCH] bcm2835-sdhost: Downgrade log message status
-
----
- drivers/mmc/host/bcm2835-sdhost.c | 4 ++--
- 1 file changed, 2 insertions(+), 2 deletions(-)
-
---- a/drivers/mmc/host/bcm2835-sdhost.c
-+++ b/drivers/mmc/host/bcm2835-sdhost.c
-@@ -232,8 +232,8 @@ static void log_init(u32 bus_to_phys)
- sdhost_log_buf = dma_zalloc_coherent(NULL, LOG_SIZE, &sdhost_log_addr,
- GFP_KERNEL);
- if (sdhost_log_buf) {
-- pr_err("sdhost: log_buf @ %p (%x)\n",
-- sdhost_log_buf, sdhost_log_addr);
-+ pr_info("sdhost: log_buf @ %p (%x)\n",
-+ sdhost_log_buf, sdhost_log_addr);
- timer_base = ioremap_nocache(bus_to_phys + 0x7e003000, SZ_4K);
- if (!timer_base)
- pr_err("sdhost: failed to remap timer\n");
diff --git a/target/linux/brcm2708/patches-4.4/0151-config-Enable-HCI-over-UARTs.patch b/target/linux/brcm2708/patches-4.4/0151-config-Enable-HCI-over-UARTs.patch
deleted file mode 100644
index 19dec6a..0000000
--- a/target/linux/brcm2708/patches-4.4/0151-config-Enable-HCI-over-UARTs.patch
+++ /dev/null
@@ -1,33 +0,0 @@
-From d0e7bd37c760d09ff5a7d28f03c4716e39864852 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 15 Jan 2016 16:48:27 +0000
-Subject: [PATCH] config: Enable HCI over UARTs
-
----
- arch/arm/configs/bcm2709_defconfig | 3 +++
- arch/arm/configs/bcmrpi_defconfig | 2 ++
- 2 files changed, 5 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -376,6 +376,9 @@ CONFIG_BT_BNEP_PROTO_FILTER=y
- CONFIG_BT_HIDP=m
- CONFIG_BT_6LOWPAN=m
- CONFIG_BT_HCIBTUSB=m
-+CONFIG_BT_HCIUART=m
-+CONFIG_BT_HCIUART_3WIRE=y
-+CONFIG_BT_HCIUART_BCM=y
- CONFIG_BT_HCIBCM203X=m
- CONFIG_BT_HCIBPA10X=m
- CONFIG_BT_HCIBFUSB=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -370,6 +370,8 @@ CONFIG_BT_HIDP=m
- CONFIG_BT_6LOWPAN=m
- CONFIG_BT_HCIBTUSB=m
- CONFIG_BT_HCIUART=m
-+CONFIG_BT_HCIUART_3WIRE=y
-+CONFIG_BT_HCIUART_BCM=y
- CONFIG_BT_HCIBCM203X=m
- CONFIG_BT_HCIBPA10X=m
- CONFIG_BT_HCIBFUSB=m
diff --git a/target/linux/brcm2708/patches-4.4/0152-hci_h5-Don-t-send-conf_req-when-ACTIVE.patch b/target/linux/brcm2708/patches-4.4/0152-hci_h5-Don-t-send-conf_req-when-ACTIVE.patch
deleted file mode 100644
index e4d7850..0000000
--- a/target/linux/brcm2708/patches-4.4/0152-hci_h5-Don-t-send-conf_req-when-ACTIVE.patch
+++ /dev/null
@@ -1,23 +0,0 @@
-From cf2d30f682d6e2f06ff51dc1694f3fb3f52b5c27 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Thu, 17 Dec 2015 13:37:07 +0000
-Subject: [PATCH] hci_h5: Don't send conf_req when ACTIVE
-
-Without this patch, a modem and kernel can continuously bombard each
-other with conf_req and conf_rsp messages, in a demented game of tag.
----
- drivers/bluetooth/hci_h5.c | 3 ++-
- 1 file changed, 2 insertions(+), 1 deletion(-)
-
---- a/drivers/bluetooth/hci_h5.c
-+++ b/drivers/bluetooth/hci_h5.c
-@@ -314,7 +314,8 @@ static void h5_handle_internal_rx(struct
- h5_link_control(hu, conf_req, 3);
- } else if (memcmp(data, conf_req, 2) == 0) {
- h5_link_control(hu, conf_rsp, 2);
-- h5_link_control(hu, conf_req, 3);
-+ if (h5->state != H5_ACTIVE)
-+ h5_link_control(hu, conf_req, 3);
- } else if (memcmp(data, conf_rsp, 2) == 0) {
- if (H5_HDR_LEN(hdr) > 2)
- h5->tx_win = (data[2] & 7);
diff --git a/target/linux/brcm2708/patches-4.4/0153-amba_pl011-Don-t-use-DT-aliases-for-numbering.patch b/target/linux/brcm2708/patches-4.4/0153-amba_pl011-Don-t-use-DT-aliases-for-numbering.patch
deleted file mode 100644
index 4088fdc..0000000
--- a/target/linux/brcm2708/patches-4.4/0153-amba_pl011-Don-t-use-DT-aliases-for-numbering.patch
+++ /dev/null
@@ -1,29 +0,0 @@
-From 171bc9150b3c330e96b2b6103885138ae9ba8cf0 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Tue, 23 Feb 2016 17:26:48 +0000
-Subject: [PATCH] amba_pl011: Don't use DT aliases for numbering
-
-The pl011 driver looks for DT aliases of the form "serial<n>",
-and if found uses <n> as the device ID. This can cause
-/dev/ttyAMA0 to become /dev/ttyAMA1, which is confusing if the
-other serial port is provided by the 8250 driver which doesn't
-use the same logic.
----
- drivers/tty/serial/amba-pl011.c | 5 +++++
- 1 file changed, 5 insertions(+)
-
---- a/drivers/tty/serial/amba-pl011.c
-+++ b/drivers/tty/serial/amba-pl011.c
-@@ -2313,7 +2313,12 @@ static int pl011_setup_port(struct devic
- if (IS_ERR(base))
- return PTR_ERR(base);
-
-+ /* Don't use DT serial<n> aliases - it causes the device to
-+ be renumbered to ttyAMA1 if it is the second serial port in the
-+ system, even though the other one is ttyS0. The 8250 driver
-+ doesn't use this logic, so always remains ttyS0.
- index = pl011_probe_dt_alias(index, dev);
-+ */
-
- uap->old_cr = 0;
- uap->port.dev = dev;
diff --git a/target/linux/brcm2708/patches-4.4/0154-clk-bcm2835-Add-bindings-for-the-auxiliary-periphera.patch b/target/linux/brcm2708/patches-4.4/0154-clk-bcm2835-Add-bindings-for-the-auxiliary-periphera.patch
deleted file mode 100644
index 3368710..0000000
--- a/target/linux/brcm2708/patches-4.4/0154-clk-bcm2835-Add-bindings-for-the-auxiliary-periphera.patch
+++ /dev/null
@@ -1,72 +0,0 @@
-From 0c4228ae6f3f3d35525fba773473015a66870dce Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 15 Dec 2015 15:35:57 -0800
-Subject: [PATCH] clk: bcm2835: Add bindings for the auxiliary peripheral clock
- gates.
-
-These will be used for enabling UART1, SPI1, and SPI2.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Acked-by: Rob Herring <robh at kernel.org>
-Signed-off-by: Michael Turquette <mturquette at baylibre.com>
----
- .../bindings/clock/brcm,bcm2835-aux-clock.txt | 31 ++++++++++++++++++++++
- include/dt-bindings/clock/bcm2835-aux.h | 17 ++++++++++++
- 2 files changed, 48 insertions(+)
- create mode 100644 Documentation/devicetree/bindings/clock/brcm,bcm2835-aux-clock.txt
- create mode 100644 include/dt-bindings/clock/bcm2835-aux.h
-
---- /dev/null
-+++ b/Documentation/devicetree/bindings/clock/brcm,bcm2835-aux-clock.txt
-@@ -0,0 +1,31 @@
-+Broadcom BCM2835 auxiliary peripheral support
-+
-+This binding uses the common clock binding:
-+ Documentation/devicetree/bindings/clock/clock-bindings.txt
-+
-+The auxiliary peripherals (UART, SPI1, and SPI2) have a small register
-+area controlling clock gating to the peripherals, and providing an IRQ
-+status register.
-+
-+Required properties:
-+- compatible: Should be "brcm,bcm2835-aux"
-+- #clock-cells: Should be <1>. The permitted clock-specifier values can be
-+ found in include/dt-bindings/clock/bcm2835-aux.h
-+- reg: Specifies base physical address and size of the registers
-+- clocks: The parent clock phandle
-+
-+Example:
-+
-+ clocks: cprman at 7e101000 {
-+ compatible = "brcm,bcm2835-cprman";
-+ #clock-cells = <1>;
-+ reg = <0x7e101000 0x2000>;
-+ clocks = <&clk_osc>;
-+ };
-+
-+ aux: aux at 0x7e215004 {
-+ compatible = "brcm,bcm2835-aux";
-+ #clock-cells = <1>;
-+ reg = <0x7e215000 0x8>;
-+ clocks = <&clocks BCM2835_CLOCK_VPU>;
-+ };
---- /dev/null
-+++ b/include/dt-bindings/clock/bcm2835-aux.h
-@@ -0,0 +1,17 @@
-+/*
-+ * Copyright (C) 2015 Broadcom Corporation
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License as
-+ * published by the Free Software Foundation version 2.
-+ *
-+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
-+ * kind, whether express or implied; without even the implied warranty
-+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ */
-+
-+#define BCM2835_AUX_CLOCK_UART 0
-+#define BCM2835_AUX_CLOCK_SPI1 1
-+#define BCM2835_AUX_CLOCK_SPI2 2
-+#define BCM2835_AUX_CLOCK_COUNT 3
diff --git a/target/linux/brcm2708/patches-4.4/0155-clk-bcm2835-Add-a-driver-for-the-auxiliary-periphera.patch b/target/linux/brcm2708/patches-4.4/0155-clk-bcm2835-Add-a-driver-for-the-auxiliary-periphera.patch
deleted file mode 100644
index 4e1911b..0000000
--- a/target/linux/brcm2708/patches-4.4/0155-clk-bcm2835-Add-a-driver-for-the-auxiliary-periphera.patch
+++ /dev/null
@@ -1,118 +0,0 @@
-From dd08a123b91b1265b9f69a7a819b0a0f907a5a6f Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 15 Dec 2015 15:35:58 -0800
-Subject: [PATCH] clk: bcm2835: Add a driver for the auxiliary peripheral clock
- gates.
-
-There are a pair of SPI masters and a mini UART that were last minute
-additions. As a result, they didn't get integrated in the same way as
-the other gates off of the VPU clock in CPRMAN.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Michael Turquette <mturquette at baylibre.com>
-
-updated Makefile to preserve the rasoberry pi architectures
----
- drivers/clk/bcm/Makefile | 1 +
- drivers/clk/bcm/clk-bcm2835-aux.c | 85 +++++++++++++++++++++++++++++++++++++++
- 2 files changed, 86 insertions(+)
- create mode 100644 drivers/clk/bcm/clk-bcm2835-aux.c
-
---- a/drivers/clk/bcm/Makefile
-+++ b/drivers/clk/bcm/Makefile
-@@ -4,6 +4,7 @@ obj-$(CONFIG_CLK_BCM_KONA) += clk-bcm281
- obj-$(CONFIG_CLK_BCM_KONA) += clk-bcm21664.o
- obj-$(CONFIG_COMMON_CLK_IPROC) += clk-iproc-armpll.o clk-iproc-pll.o clk-iproc-asiu.o
- obj-$(CONFIG_ARCH_BCM2835)$(CONFIG_ARCH_BCM2708)$(CONFIG_ARCH_BCM2709) += clk-bcm2835.o
-+obj-$(CONFIG_ARCH_BCM2835) += clk-bcm2835-aux.o
- obj-$(CONFIG_COMMON_CLK_IPROC) += clk-ns2.o
- obj-$(CONFIG_ARCH_BCM_CYGNUS) += clk-cygnus.o
- obj-$(CONFIG_ARCH_BCM_NSP) += clk-nsp.o
---- /dev/null
-+++ b/drivers/clk/bcm/clk-bcm2835-aux.c
-@@ -0,0 +1,85 @@
-+/*
-+ * Copyright (C) 2015 Broadcom
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ */
-+
-+#include <linux/clk.h>
-+#include <linux/clk-provider.h>
-+#include <linux/clk/bcm2835.h>
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+#include <dt-bindings/clock/bcm2835-aux.h>
-+
-+#define BCM2835_AUXIRQ 0x00
-+#define BCM2835_AUXENB 0x04
-+
-+static int bcm2835_aux_clk_probe(struct platform_device *pdev)
-+{
-+ struct device *dev = &pdev->dev;
-+ struct clk_onecell_data *onecell;
-+ const char *parent;
-+ struct clk *parent_clk;
-+ struct resource *res;
-+ void __iomem *reg, *gate;
-+
-+ parent_clk = devm_clk_get(dev, NULL);
-+ if (IS_ERR(parent_clk))
-+ return PTR_ERR(parent_clk);
-+ parent = __clk_get_name(parent_clk);
-+
-+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+ reg = devm_ioremap_resource(dev, res);
-+ if (!reg)
-+ return -ENODEV;
-+
-+ onecell = devm_kmalloc(dev, sizeof(*onecell), GFP_KERNEL);
-+ if (!onecell)
-+ return -ENOMEM;
-+ onecell->clk_num = BCM2835_AUX_CLOCK_COUNT;
-+ onecell->clks = devm_kcalloc(dev, BCM2835_AUX_CLOCK_COUNT,
-+ sizeof(*onecell->clks), GFP_KERNEL);
-+ if (!onecell->clks)
-+ return -ENOMEM;
-+
-+ gate = reg + BCM2835_AUXENB;
-+ onecell->clks[BCM2835_AUX_CLOCK_UART] =
-+ clk_register_gate(dev, "aux_uart", parent, 0, gate, 0, 0, NULL);
-+
-+ onecell->clks[BCM2835_AUX_CLOCK_SPI1] =
-+ clk_register_gate(dev, "aux_spi1", parent, 0, gate, 1, 0, NULL);
-+
-+ onecell->clks[BCM2835_AUX_CLOCK_SPI2] =
-+ clk_register_gate(dev, "aux_spi2", parent, 0, gate, 2, 0, NULL);
-+
-+ of_clk_add_provider(pdev->dev.of_node, of_clk_src_onecell_get, onecell);
-+
-+ return 0;
-+}
-+
-+static const struct of_device_id bcm2835_aux_clk_of_match[] = {
-+ { .compatible = "brcm,bcm2835-aux", },
-+ {},
-+};
-+MODULE_DEVICE_TABLE(of, bcm2835_aux_clk_of_match);
-+
-+static struct platform_driver bcm2835_aux_clk_driver = {
-+ .driver = {
-+ .name = "bcm2835-aux-clk",
-+ .of_match_table = bcm2835_aux_clk_of_match,
-+ },
-+ .probe = bcm2835_aux_clk_probe,
-+};
-+builtin_platform_driver(bcm2835_aux_clk_driver);
-+
-+MODULE_AUTHOR("Eric Anholt <eric at anholt.net>");
-+MODULE_DESCRIPTION("BCM2835 auxiliary peripheral clock driver");
-+MODULE_LICENSE("GPL v2");
diff --git a/target/linux/brcm2708/patches-4.4/0156-Aux-SPI-1-2-implementation.patch b/target/linux/brcm2708/patches-4.4/0156-Aux-SPI-1-2-implementation.patch
deleted file mode 100644
index f4d0436..0000000
--- a/target/linux/brcm2708/patches-4.4/0156-Aux-SPI-1-2-implementation.patch
+++ /dev/null
@@ -1,700 +0,0 @@
-From d8576480efc07f6abcf0ffbd0320ba15804fb22d Mon Sep 17 00:00:00 2001
-From: Fraser <github at frasersdev.net>
-Date: Tue, 23 Feb 2016 10:04:37 +1100
-Subject: [PATCH] Aux SPI 1&2 implementation
-
-Adds aux spi 1 & 2 devices to compatible raspberry PIs.
-* Minor config of the driver build environment to ensure they get built
-for CONFIG_ARCH_BCM2708 & CONFIG_ARCH_BCM2709 devices.
-* Adds the aux spi driver into the defconfigs as a module.
-* Adds the auxiliary and spi1/2 devices into the device tree in a
-disabled state
-* Provides decide tree overlays which enables the devices and gives
-users a degree of control over how they are setup.
----
- arch/arm/boot/dts/bcm2708_common.dtsi | 34 ++++++++-
- arch/arm/boot/dts/overlays/Makefile | 6 ++
- arch/arm/boot/dts/overlays/README | 99 +++++++++++++++++++++++++
- arch/arm/boot/dts/overlays/spi1-1cs-overlay.dts | 57 ++++++++++++++
- arch/arm/boot/dts/overlays/spi1-2cs-overlay.dts | 69 +++++++++++++++++
- arch/arm/boot/dts/overlays/spi1-3cs-overlay.dts | 81 ++++++++++++++++++++
- arch/arm/boot/dts/overlays/spi2-1cs-overlay.dts | 57 ++++++++++++++
- arch/arm/boot/dts/overlays/spi2-2cs-overlay.dts | 69 +++++++++++++++++
- arch/arm/boot/dts/overlays/spi2-3cs-overlay.dts | 81 ++++++++++++++++++++
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- drivers/clk/bcm/Makefile | 2 +-
- drivers/spi/Kconfig | 2 +-
- 13 files changed, 556 insertions(+), 3 deletions(-)
- create mode 100644 arch/arm/boot/dts/overlays/spi1-1cs-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/spi1-2cs-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/spi1-3cs-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/spi2-1cs-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/spi2-2cs-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/spi2-3cs-overlay.dts
-
---- a/arch/arm/boot/dts/bcm2708_common.dtsi
-+++ b/arch/arm/boot/dts/bcm2708_common.dtsi
-@@ -1,3 +1,4 @@
-+#include <dt-bindings/clock/bcm2835-aux.h>
- #include "skeleton.dtsi"
-
- / {
-@@ -5,6 +6,7 @@
-
- aliases {
- audio = &audio;
-+ aux = &aux;
- sound = &sound;
- soc = &soc;
- dma = &dma;
-@@ -19,6 +21,8 @@
- spi0 = &spi0;
- i2c0 = &i2c0;
- uart1 = &uart1;
-+ spi1 = &spi1;
-+ spi2 = &spi2;
- mmc = &mmc;
- i2c1 = &i2c1;
- i2c2 = &i2c2;
-@@ -186,6 +190,14 @@
- status = "disabled";
- };
-
-+ aux: aux at 0x7e215004 {
-+ compatible = "brcm,bcm2835-aux";
-+ #clock-cells = <1>;
-+ reg = <0x7e215000 0x8>;
-+ clocks = <&clk_core>;
-+ status = "disabled";
-+ };
-+
- uart1: uart at 7e215040 {
- compatible = "brcm,bcm2835-aux-uart", "ns16550";
- reg = <0x7e215040 0x40>;
-@@ -194,7 +206,27 @@
- reg-shift = <2>;
- no-loopback-test;
- status = "disabled";
-- };
-+ };
-+
-+ spi1: spi at 7e215080 {
-+ compatible = "brcm,bcm2835-aux-spi";
-+ reg = <0x7e215080 0x40>, <0x7e215000 0x8>;
-+ interrupts = <1 29>;
-+ clocks = <&aux BCM2835_AUX_CLOCK_SPI1>;
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "disabled";
-+ };
-+
-+ spi2: spi at 7e2150C0 {
-+ compatible = "brcm,bcm2835-aux-spi";
-+ reg = <0x7e2150C0 0x40>, <0x7e215000 0x8>;
-+ interrupts = <1 29>;
-+ clocks = <&aux BCM2835_AUX_CLOCK_SPI2>;
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "disabled";
-+ };
-
- mmc: mmc at 7e300000 {
- compatible = "brcm,bcm2835-mmc";
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -57,6 +57,12 @@ dtb-$(RPI_DT_OVERLAYS) += sdtweak-overla
- dtb-$(RPI_DT_OVERLAYS) += smi-dev-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += smi-nand-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += smi-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += spi1-1cs-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += spi1-2cs-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += spi1-3cs-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += spi2-1cs-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += spi2-2cs-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += spi2-3cs-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += spi-gpio35-39-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += tinylcd35-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += uart1-overlay.dtb
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -713,6 +713,105 @@ Load: dtoverlay=spi-gpio35-39
- Params: <None>
-
-
-+Name: spi1-1cs
-+Info: Enables spi1 with a single chip select (CS) line and associated spidev
-+ dev node. The gpio pin number for the CS line and spidev device node
-+ creation are configurable.
-+ N.B.: spi1 is only accessible on devices with a 40pin header, eg:
-+ A+, B+, Zero and PI2 B; as well as the Compute Module.
-+Load: dtoverlay=spi1-1cs,<param>=<val>
-+Params: cs0_pin GPIO pin for CS0 (default 18 - BCM SPI1_CE0).
-+ cs0_spidev Set to 'disabled' to stop the creation of a
-+ userspace device node /dev/spidev1.0 (default
-+ is 'okay' or enabled).
-+
-+
-+Name: spi1-2cs
-+Info: Enables spi1 with two chip select (CS) lines and associated spidev
-+ dev nodes. The gpio pin numbers for the CS lines and spidev device node
-+ creation are configurable.
-+ N.B.: spi1 is only accessible on devices with a 40pin header, eg:
-+ A+, B+, Zero and PI2 B; as well as the Compute Module.
-+Load: dtoverlay=spi1-2cs,<param>=<val>
-+Params: cs0_pin GPIO pin for CS0 (default 18 - BCM SPI1_CE0).
-+ cs1_pin GPIO pin for CS1 (default 17 - BCM SPI1_CE1).
-+ cs0_spidev Set to 'disabled' to stop the creation of a
-+ userspace device node /dev/spidev1.0 (default
-+ is 'okay' or enabled).
-+ cs1_spidev Set to 'disabled' to stop the creation of a
-+ userspace device node /dev/spidev1.1 (default
-+ is 'okay' or enabled).
-+
-+
-+Name: spi1-3cs
-+Info: Enables spi1 with three chip select (CS) lines and associated spidev
-+ dev nodes. The gpio pin numbers for the CS lines and spidev device node
-+ creation are configurable.
-+ N.B.: spi1 is only accessible on devices with a 40pin header, eg:
-+ A+, B+, Zero and PI2 B; as well as the Compute Module.
-+Load: dtoverlay=spi1-3cs,<param>=<val>
-+Params: cs0_pin GPIO pin for CS0 (default 18 - BCM SPI1_CE0).
-+ cs1_pin GPIO pin for CS1 (default 17 - BCM SPI1_CE1).
-+ cs2_pin GPIO pin for CS2 (default 16 - BCM SPI1_CE2).
-+ cs0_spidev Set to 'disabled' to stop the creation of a
-+ userspace device node /dev/spidev1.0 (default
-+ is 'okay' or enabled).
-+ cs1_spidev Set to 'disabled' to stop the creation of a
-+ userspace device node /dev/spidev1.1 (default
-+ is 'okay' or enabled).
-+ cs2_spidev Set to 'disabled' to stop the creation of a
-+ userspace device node /dev/spidev1.2 (default
-+ is 'okay' or enabled).
-+
-+
-+Name: spi2-1cs
-+Info: Enables spi2 with a single chip select (CS) line and associated spidev
-+ dev node. The gpio pin number for the CS line and spidev device node
-+ creation are configurable.
-+ N.B.: spi2 is only accessible with the Compute Module.
-+Load: dtoverlay=spi2-1cs,<param>=<val>
-+Params: cs0_pin GPIO pin for CS0 (default 43 - BCM SPI2_CE0).
-+ cs0_spidev Set to 'disabled' to stop the creation of a
-+ userspace device node /dev/spidev2.0 (default
-+ is 'okay' or enabled).
-+
-+
-+Name: spi2-2cs
-+Info: Enables spi2 with two chip select (CS) lines and associated spidev
-+ dev nodes. The gpio pin numbers for the CS lines and spidev device node
-+ creation are configurable.
-+ N.B.: spi2 is only accessible with the Compute Module.
-+Load: dtoverlay=spi2-2cs,<param>=<val>
-+Params: cs0_pin GPIO pin for CS0 (default 43 - BCM SPI2_CE0).
-+ cs1_pin GPIO pin for CS1 (default 44 - BCM SPI2_CE1).
-+ cs0_spidev Set to 'disabled' to stop the creation of a
-+ userspace device node /dev/spidev2.0 (default
-+ is 'okay' or enabled).
-+ cs1_spidev Set to 'disabled' to stop the creation of a
-+ userspace device node /dev/spidev2.1 (default
-+ is 'okay' or enabled).
-+
-+
-+Name: spi2-3cs
-+Info: Enables spi2 with three chip select (CS) lines and associated spidev
-+ dev nodes. The gpio pin numbers for the CS lines and spidev device node
-+ creation are configurable.
-+ N.B.: spi2 is only accessible with the Compute Module.
-+Load: dtoverlay=spi2-3cs,<param>=<val>
-+Params: cs0_pin GPIO pin for CS0 (default 43 - BCM SPI2_CE0).
-+ cs1_pin GPIO pin for CS1 (default 44 - BCM SPI2_CE1).
-+ cs2_pin GPIO pin for CS2 (default 45 - BCM SPI2_CE2).
-+ cs0_spidev Set to 'disabled' to stop the creation of a
-+ userspace device node /dev/spidev2.0 (default
-+ is 'okay' or enabled).
-+ cs1_spidev Set to 'disabled' to stop the creation of a
-+ userspace device node /dev/spidev2.1 (default
-+ is 'okay' or enabled).
-+ cs2_spidev Set to 'disabled' to stop the creation of a
-+ userspace device node /dev/spidev2.2 (default
-+ is 'okay' or enabled).
-+
-+
- Name: tinylcd35
- Info: 3.5" Color TFT Display by www.tinylcd.com
- Options: Touch, RTC, keypad
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/spi1-1cs-overlay.dts
-@@ -0,0 +1,57 @@
-+/dts-v1/;
-+/plugin/;
-+
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ spi1_pins: spi1_pins {
-+ brcm,pins = <19 20 21>;
-+ brcm,function = <3>; /* alt4 */
-+ };
-+
-+ spi1_cs_pins: spi1_cs_pins {
-+ brcm,pins = <18>;
-+ brcm,function = <1>; /* output */
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&spi1>;
-+ frag1: __overlay__ {
-+ /* needed to avoid dtc warning */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&spi1_pins &spi1_cs_pins>;
-+ cs-gpios = <&gpio 18 1>;
-+ status = "okay";
-+
-+ spidev1_0: spidev at 0 {
-+ compatible = "spidev";
-+ reg = <0>; /* CE0 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&aux>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ __overrides__ {
-+ cs0_pin = <&spi1_cs_pins>,"brcm,pins:0",
-+ <&frag1>,"cs-gpios:4";
-+ cs0_spidev = <&spidev1_0>,"status";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/spi1-2cs-overlay.dts
-@@ -0,0 +1,69 @@
-+/dts-v1/;
-+/plugin/;
-+
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ spi1_pins: spi1_pins {
-+ brcm,pins = <19 20 21>;
-+ brcm,function = <3>; /* alt4 */
-+ };
-+
-+ spi1_cs_pins: spi1_cs_pins {
-+ brcm,pins = <18 17>;
-+ brcm,function = <1>; /* output */
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&spi1>;
-+ frag1: __overlay__ {
-+ /* needed to avoid dtc warning */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&spi1_pins &spi1_cs_pins>;
-+ cs-gpios = <&gpio 18 1>, <&gpio 17 1>;
-+ status = "okay";
-+
-+ spidev1_0: spidev at 0 {
-+ compatible = "spidev";
-+ reg = <0>; /* CE0 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ };
-+
-+ spidev1_1: spidev at 1 {
-+ compatible = "spidev";
-+ reg = <1>; /* CE1 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&aux>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ __overrides__ {
-+ cs0_pin = <&spi1_cs_pins>,"brcm,pins:0",
-+ <&frag1>,"cs-gpios:4";
-+ cs1_pin = <&spi1_cs_pins>,"brcm,pins:4",
-+ <&frag1>,"cs-gpios:16";
-+ cs0_spidev = <&spidev1_0>,"status";
-+ cs1_spidev = <&spidev1_1>,"status";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/spi1-3cs-overlay.dts
-@@ -0,0 +1,81 @@
-+/dts-v1/;
-+/plugin/;
-+
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ spi1_pins: spi1_pins {
-+ brcm,pins = <19 20 21>;
-+ brcm,function = <3>; /* alt4 */
-+ };
-+
-+ spi1_cs_pins: spi1_cs_pins {
-+ brcm,pins = <18 17 16>;
-+ brcm,function = <1>; /* output */
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&spi1>;
-+ frag1: __overlay__ {
-+ /* needed to avoid dtc warning */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&spi1_pins &spi1_cs_pins>;
-+ cs-gpios = <&gpio 18 1>, <&gpio 17 1>, <&gpio 16 1>;
-+ status = "okay";
-+
-+ spidev1_0: spidev at 0 {
-+ compatible = "spidev";
-+ reg = <0>; /* CE0 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ };
-+
-+ spidev1_1: spidev at 1 {
-+ compatible = "spidev";
-+ reg = <1>; /* CE1 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ };
-+
-+ spidev1_2: spidev at 2 {
-+ compatible = "spidev";
-+ reg = <2>; /* CE2 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&aux>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ __overrides__ {
-+ cs0_pin = <&spi1_cs_pins>,"brcm,pins:0",
-+ <&frag1>,"cs-gpios:4";
-+ cs1_pin = <&spi1_cs_pins>,"brcm,pins:4",
-+ <&frag1>,"cs-gpios:16";
-+ cs2_pin = <&spi1_cs_pins>,"brcm,pins:8",
-+ <&frag1>,"cs-gpios:28";
-+ cs0_spidev = <&spidev1_0>,"status";
-+ cs1_spidev = <&spidev1_1>,"status";
-+ cs2_spidev = <&spidev1_2>,"status";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/spi2-1cs-overlay.dts
-@@ -0,0 +1,57 @@
-+/dts-v1/;
-+/plugin/;
-+
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ spi2_pins: spi2_pins {
-+ brcm,pins = <40 41 42>;
-+ brcm,function = <3>; /* alt4 */
-+ };
-+
-+ spi2_cs_pins: spi2_cs_pins {
-+ brcm,pins = <43>;
-+ brcm,function = <1>; /* output */
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&spi2>;
-+ frag1: __overlay__ {
-+ /* needed to avoid dtc warning */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&spi2_pins &spi2_cs_pins>;
-+ cs-gpios = <&gpio 43 1>;
-+ status = "okay";
-+
-+ spidev2_0: spidev at 0 {
-+ compatible = "spidev";
-+ reg = <0>; /* CE0 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&aux>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ __overrides__ {
-+ cs0_pin = <&spi2_cs_pins>,"brcm,pins:0",
-+ <&frag1>,"cs-gpios:4";
-+ cs0_spidev = <&spidev2_0>,"status";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/spi2-2cs-overlay.dts
-@@ -0,0 +1,69 @@
-+/dts-v1/;
-+/plugin/;
-+
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ spi2_pins: spi2_pins {
-+ brcm,pins = <40 41 42>;
-+ brcm,function = <3>; /* alt4 */
-+ };
-+
-+ spi2_cs_pins: spi2_cs_pins {
-+ brcm,pins = <43 44>;
-+ brcm,function = <1>; /* output */
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&spi2>;
-+ frag1: __overlay__ {
-+ /* needed to avoid dtc warning */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&spi2_pins &spi2_cs_pins>;
-+ cs-gpios = <&gpio 43 1>, <&gpio 44 1>;
-+ status = "okay";
-+
-+ spidev2_0: spidev at 0 {
-+ compatible = "spidev";
-+ reg = <0>; /* CE0 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ };
-+
-+ spidev2_1: spidev at 1 {
-+ compatible = "spidev";
-+ reg = <1>; /* CE1 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&aux>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ __overrides__ {
-+ cs0_pin = <&spi2_cs_pins>,"brcm,pins:0",
-+ <&frag1>,"cs-gpios:4";
-+ cs1_pin = <&spi2_cs_pins>,"brcm,pins:4",
-+ <&frag1>,"cs-gpios:16";
-+ cs0_spidev = <&spidev2_0>,"status";
-+ cs1_spidev = <&spidev2_1>,"status";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/spi2-3cs-overlay.dts
-@@ -0,0 +1,81 @@
-+/dts-v1/;
-+/plugin/;
-+
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ spi2_pins: spi2_pins {
-+ brcm,pins = <40 41 42>;
-+ brcm,function = <3>; /* alt4 */
-+ };
-+
-+ spi2_cs_pins: spi2_cs_pins {
-+ brcm,pins = <43 44 45>;
-+ brcm,function = <1>; /* output */
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&spi2>;
-+ frag1: __overlay__ {
-+ /* needed to avoid dtc warning */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&spi2_pins &spi2_cs_pins>;
-+ cs-gpios = <&gpio 43 1>, <&gpio 44 1>, <&gpio 45 1>;
-+ status = "okay";
-+
-+ spidev2_0: spidev at 0 {
-+ compatible = "spidev";
-+ reg = <0>; /* CE0 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ };
-+
-+ spidev2_1: spidev at 1 {
-+ compatible = "spidev";
-+ reg = <1>; /* CE1 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ };
-+
-+ spidev2_2: spidev at 2 {
-+ compatible = "spidev";
-+ reg = <2>; /* CE2 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&aux>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ __overrides__ {
-+ cs0_pin = <&spi2_cs_pins>,"brcm,pins:0",
-+ <&frag1>,"cs-gpios:4";
-+ cs1_pin = <&spi2_cs_pins>,"brcm,pins:4",
-+ <&frag1>,"cs-gpios:16";
-+ cs2_pin = <&spi2_cs_pins>,"brcm,pins:8",
-+ <&frag1>,"cs-gpios:28";
-+ cs0_spidev = <&spidev2_0>,"status";
-+ cs1_spidev = <&spidev2_1>,"status";
-+ cs2_spidev = <&spidev2_2>,"status";
-+ };
-+};
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -601,6 +601,7 @@ CONFIG_I2C_BCM2708=m
- CONFIG_I2C_GPIO=m
- CONFIG_SPI=y
- CONFIG_SPI_BCM2835=m
-+CONFIG_SPI_BCM2835AUX=m
- CONFIG_SPI_SPIDEV=y
- CONFIG_PPS=m
- CONFIG_PPS_CLIENT_LDISC=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -593,6 +593,7 @@ CONFIG_I2C_BCM2708=m
- CONFIG_I2C_GPIO=m
- CONFIG_SPI=y
- CONFIG_SPI_BCM2835=m
-+CONFIG_SPI_BCM2835AUX=m
- CONFIG_SPI_SPIDEV=y
- CONFIG_PPS=m
- CONFIG_PPS_CLIENT_LDISC=m
---- a/drivers/clk/bcm/Makefile
-+++ b/drivers/clk/bcm/Makefile
-@@ -4,7 +4,7 @@ obj-$(CONFIG_CLK_BCM_KONA) += clk-bcm281
- obj-$(CONFIG_CLK_BCM_KONA) += clk-bcm21664.o
- obj-$(CONFIG_COMMON_CLK_IPROC) += clk-iproc-armpll.o clk-iproc-pll.o clk-iproc-asiu.o
- obj-$(CONFIG_ARCH_BCM2835)$(CONFIG_ARCH_BCM2708)$(CONFIG_ARCH_BCM2709) += clk-bcm2835.o
--obj-$(CONFIG_ARCH_BCM2835) += clk-bcm2835-aux.o
-+obj-$(CONFIG_ARCH_BCM2835)$(CONFIG_ARCH_BCM2708)$(CONFIG_ARCH_BCM2709) += clk-bcm2835-aux.o
- obj-$(CONFIG_COMMON_CLK_IPROC) += clk-ns2.o
- obj-$(CONFIG_ARCH_BCM_CYGNUS) += clk-cygnus.o
- obj-$(CONFIG_ARCH_BCM_NSP) += clk-nsp.o
---- a/drivers/spi/Kconfig
-+++ b/drivers/spi/Kconfig
-@@ -90,7 +90,7 @@ config SPI_BCM2835
-
- config SPI_BCM2835AUX
- tristate "BCM2835 SPI auxiliary controller"
-- depends on ARCH_BCM2835 || COMPILE_TEST
-+ depends on ARCH_BCM2835 || ARCH_BCM2708 || ARCH_BCM2709 || COMPILE_TEST
- depends on GPIOLIB
- help
- This selects a driver for the Broadcom BCM2835 SPI aux master.
diff --git a/target/linux/brcm2708/patches-4.4/0157-ASoC-bcm-add-missing-.owner-fields-in-sound-card-dri.patch b/target/linux/brcm2708/patches-4.4/0157-ASoC-bcm-add-missing-.owner-fields-in-sound-card-dri.patch
deleted file mode 100644
index 73ef160..0000000
--- a/target/linux/brcm2708/patches-4.4/0157-ASoC-bcm-add-missing-.owner-fields-in-sound-card-dri.patch
+++ /dev/null
@@ -1,107 +0,0 @@
-From 3723d7a10e6e45a49e35bbd06d723b739ff86970 Mon Sep 17 00:00:00 2001
-From: Matthias Reichl <hias at horus.com>
-Date: Tue, 23 Feb 2016 17:28:23 +0100
-Subject: [PATCH] ASoC: bcm: add missing .owner fields in sound card drivers
-
-If snd_soc_card.owner is not set the kernel won't do usage refcounting
-and one can remove the card driver module while it's in use (eg playback
-active) - which leads to a kernel crash.
-
-The missing owner field also prevents ALSA slot ordering
-(options snd slots=module-name1,module-name-2,...) from working with
-the I2S cards as it has no module name to match against.
-
-Fix these issues by setting the .owner field in the snd_soc_card structs.
-
-Signed-off-by: Matthias Reichl <hias at horus.com>
----
- sound/soc/bcm/hifiberry_amp.c | 1 +
- sound/soc/bcm/hifiberry_dac.c | 1 +
- sound/soc/bcm/hifiberry_dacplus.c | 1 +
- sound/soc/bcm/hifiberry_digi.c | 1 +
- sound/soc/bcm/iqaudio-dac.c | 1 +
- sound/soc/bcm/raspidac3.c | 1 +
- sound/soc/bcm/rpi-dac.c | 1 +
- sound/soc/bcm/rpi-proto.c | 1 +
- 8 files changed, 8 insertions(+)
-
---- a/sound/soc/bcm/hifiberry_amp.c
-+++ b/sound/soc/bcm/hifiberry_amp.c
-@@ -61,6 +61,7 @@ static struct snd_soc_dai_link snd_rpi_h
-
- static struct snd_soc_card snd_rpi_hifiberry_amp = {
- .name = "snd_rpi_hifiberry_amp",
-+ .owner = THIS_MODULE,
- .dai_link = snd_rpi_hifiberry_amp_dai,
- .num_links = ARRAY_SIZE(snd_rpi_hifiberry_amp_dai),
- };
---- a/sound/soc/bcm/hifiberry_dac.c
-+++ b/sound/soc/bcm/hifiberry_dac.c
-@@ -63,6 +63,7 @@ static struct snd_soc_dai_link snd_rpi_h
- /* audio machine driver */
- static struct snd_soc_card snd_rpi_hifiberry_dac = {
- .name = "snd_rpi_hifiberry_dac",
-+ .owner = THIS_MODULE,
- .dai_link = snd_rpi_hifiberry_dac_dai,
- .num_links = ARRAY_SIZE(snd_rpi_hifiberry_dac_dai),
- };
---- a/sound/soc/bcm/hifiberry_dacplus.c
-+++ b/sound/soc/bcm/hifiberry_dacplus.c
-@@ -287,6 +287,7 @@ static struct snd_soc_dai_link snd_rpi_h
- /* audio machine driver */
- static struct snd_soc_card snd_rpi_hifiberry_dacplus = {
- .name = "snd_rpi_hifiberry_dacplus",
-+ .owner = THIS_MODULE,
- .dai_link = snd_rpi_hifiberry_dacplus_dai,
- .num_links = ARRAY_SIZE(snd_rpi_hifiberry_dacplus_dai),
- };
---- a/sound/soc/bcm/hifiberry_digi.c
-+++ b/sound/soc/bcm/hifiberry_digi.c
-@@ -164,6 +164,7 @@ static struct snd_soc_dai_link snd_rpi_h
- /* audio machine driver */
- static struct snd_soc_card snd_rpi_hifiberry_digi = {
- .name = "snd_rpi_hifiberry_digi",
-+ .owner = THIS_MODULE,
- .dai_link = snd_rpi_hifiberry_digi_dai,
- .num_links = ARRAY_SIZE(snd_rpi_hifiberry_digi_dai),
- };
---- a/sound/soc/bcm/iqaudio-dac.c
-+++ b/sound/soc/bcm/iqaudio-dac.c
-@@ -77,6 +77,7 @@ static struct snd_soc_dai_link snd_rpi_i
- /* audio machine driver */
- static struct snd_soc_card snd_rpi_iqaudio_dac = {
- .name = "IQaudIODAC",
-+ .owner = THIS_MODULE,
- .dai_link = snd_rpi_iqaudio_dac_dai,
- .num_links = ARRAY_SIZE(snd_rpi_iqaudio_dac_dai),
- };
---- a/sound/soc/bcm/raspidac3.c
-+++ b/sound/soc/bcm/raspidac3.c
-@@ -128,6 +128,7 @@ static struct snd_soc_dai_link snd_rpi_r
- /* audio machine driver */
- static struct snd_soc_card snd_rpi_raspidac3 = {
- .name = "RaspiDAC Rev.3x HiFi Audio Card",
-+ .owner = THIS_MODULE,
- .dai_link = snd_rpi_raspidac3_dai,
- .num_links = ARRAY_SIZE(snd_rpi_raspidac3_dai),
- };
---- a/sound/soc/bcm/rpi-dac.c
-+++ b/sound/soc/bcm/rpi-dac.c
-@@ -60,6 +60,7 @@ static struct snd_soc_dai_link snd_rpi_r
- /* audio machine driver */
- static struct snd_soc_card snd_rpi_rpi_dac = {
- .name = "snd_rpi_rpi_dac",
-+ .owner = THIS_MODULE,
- .dai_link = snd_rpi_rpi_dac_dai,
- .num_links = ARRAY_SIZE(snd_rpi_rpi_dac_dai),
- };
---- a/sound/soc/bcm/rpi-proto.c
-+++ b/sound/soc/bcm/rpi-proto.c
-@@ -91,6 +91,7 @@ static struct snd_soc_dai_link snd_rpi_p
- /* audio machine driver */
- static struct snd_soc_card snd_rpi_proto = {
- .name = "snd_rpi_proto",
-+ .owner = THIS_MODULE,
- .dai_link = snd_rpi_proto_dai,
- .num_links = ARRAY_SIZE(snd_rpi_proto_dai),
- };
diff --git a/target/linux/brcm2708/patches-4.4/0158-smsx95xx-Add-option-to-disable-the-crimes-against-tr.patch b/target/linux/brcm2708/patches-4.4/0158-smsx95xx-Add-option-to-disable-the-crimes-against-tr.patch
deleted file mode 100644
index 7f0a8f0..0000000
--- a/target/linux/brcm2708/patches-4.4/0158-smsx95xx-Add-option-to-disable-the-crimes-against-tr.patch
+++ /dev/null
@@ -1,44 +0,0 @@
-From 0e33a60fe54f789da20be92571531013a5625e63 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Wed, 20 Jan 2016 17:50:09 +0000
-Subject: [PATCH] smsx95xx: Add option to disable the crimes against truesize
- fix
-
-It may improve iperf numbers on Pi 1, but may generate dmesg warnings and possibly cause network issues
-See issue 1248.
----
- drivers/net/usb/smsc95xx.c | 8 ++++++++
- 1 file changed, 8 insertions(+)
- mode change 100755 => 100644 drivers/net/usb/smsc95xx.c
-
---- a/drivers/net/usb/smsc95xx.c
-+++ b/drivers/net/usb/smsc95xx.c
-@@ -75,6 +75,10 @@ static bool turbo_mode = false;
- module_param(turbo_mode, bool, 0644);
- MODULE_PARM_DESC(turbo_mode, "Enable multiple frames per Rx transaction");
-
-+static bool truesize_mode = false;
-+module_param(truesize_mode, bool, 0644);
-+MODULE_PARM_DESC(truesize_mode, "Report larger truesize value");
-+
- static char *macaddr = ":";
- module_param(macaddr, charp, 0);
- MODULE_PARM_DESC(macaddr, "MAC address");
-@@ -1841,6 +1845,8 @@ static int smsc95xx_rx_fixup(struct usbn
- if (dev->net->features & NETIF_F_RXCSUM)
- smsc95xx_rx_csum_offload(skb);
- skb_trim(skb, skb->len - 4); /* remove fcs */
-+ if (truesize_mode)
-+ skb->truesize = size + sizeof(struct sk_buff);
-
- return 1;
- }
-@@ -1858,6 +1864,8 @@ static int smsc95xx_rx_fixup(struct usbn
- if (dev->net->features & NETIF_F_RXCSUM)
- smsc95xx_rx_csum_offload(ax_skb);
- skb_trim(ax_skb, ax_skb->len - 4); /* remove fcs */
-+ if (truesize_mode)
-+ ax_skb->truesize = size + sizeof(struct sk_buff);
-
- usbnet_skb_return(dev, ax_skb);
- }
diff --git a/target/linux/brcm2708/patches-4.4/0159-bcm2835-virtgpio-Virtual-GPIO-driver.patch b/target/linux/brcm2708/patches-4.4/0159-bcm2835-virtgpio-Virtual-GPIO-driver.patch
deleted file mode 100644
index fe19fbe..0000000
--- a/target/linux/brcm2708/patches-4.4/0159-bcm2835-virtgpio-Virtual-GPIO-driver.patch
+++ /dev/null
@@ -1,244 +0,0 @@
-From 2fcaab4e60a00ed9b63606b45ae499d7c5561c16 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Tue, 23 Feb 2016 19:56:04 +0000
-Subject: [PATCH] bcm2835-virtgpio: Virtual GPIO driver
-
-Add a virtual GPIO driver that uses the firmware mailbox interface to
-request that the VPU toggles LEDs.
----
- arch/arm/configs/bcm2709_defconfig | 1 +
- drivers/gpio/Kconfig | 6 +
- drivers/gpio/Makefile | 1 +
- drivers/gpio/gpio-bcm-virt.c | 180 +++++++++++++++++++++++++++++
- include/soc/bcm2835/raspberrypi-firmware.h | 1 +
- 5 files changed, 189 insertions(+)
- create mode 100644 drivers/gpio/gpio-bcm-virt.c
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -607,6 +607,7 @@ CONFIG_PPS=m
- CONFIG_PPS_CLIENT_LDISC=m
- CONFIG_PPS_CLIENT_GPIO=m
- CONFIG_GPIO_SYSFS=y
-+CONFIG_GPIO_BCM_VIRT=y
- CONFIG_GPIO_ARIZONA=m
- CONFIG_GPIO_STMPE=y
- CONFIG_W1=m
---- a/drivers/gpio/Kconfig
-+++ b/drivers/gpio/Kconfig
-@@ -133,6 +133,12 @@ config GPIO_BCM_KONA
- help
- Turn on GPIO support for Broadcom "Kona" chips.
-
-+config GPIO_BCM_VIRT
-+ bool "Broadcom Virt GPIO"
-+ depends on OF_GPIO && RASPBERRYPI_FIRMWARE && (ARCH_BCM2835 || ARCH_BCM2708 || ARCH_BCM2709 || COMPILE_TEST)
-+ help
-+ Turn on virtual GPIO support for Broadcom BCM283X chips.
-+
- config GPIO_BRCMSTB
- tristate "BRCMSTB GPIO support"
- default y if ARCH_BRCMSTB
---- a/drivers/gpio/Makefile
-+++ b/drivers/gpio/Makefile
-@@ -24,6 +24,7 @@ obj-$(CONFIG_GPIO_AMDPT) += gpio-amdpt.o
- obj-$(CONFIG_GPIO_ARIZONA) += gpio-arizona.o
- obj-$(CONFIG_ATH79) += gpio-ath79.o
- obj-$(CONFIG_GPIO_BCM_KONA) += gpio-bcm-kona.o
-+obj-$(CONFIG_GPIO_BCM_VIRT) += gpio-bcm-virt.o
- obj-$(CONFIG_GPIO_BRCMSTB) += gpio-brcmstb.o
- obj-$(CONFIG_GPIO_BT8XX) += gpio-bt8xx.o
- obj-$(CONFIG_GPIO_CLPS711X) += gpio-clps711x.o
---- /dev/null
-+++ b/drivers/gpio/gpio-bcm-virt.c
-@@ -0,0 +1,180 @@
-+/*
-+ * brcmvirt GPIO driver
-+ *
-+ * Copyright (C) 2012,2013 Dom Cobley <popcornmix at gmail.com>
-+ * Based on gpio-clps711x.c by Alexander Shiyan <shc_work at mail.ru>
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ */
-+
-+#include <linux/err.h>
-+#include <linux/gpio.h>
-+#include <linux/module.h>
-+#include <linux/basic_mmio_gpio.h>
-+#include <linux/platform_device.h>
-+#include <soc/bcm2835/raspberrypi-firmware.h>
-+
-+#define MODULE_NAME "brcmvirt-gpio"
-+#define NUM_GPIO 2
-+
-+struct brcmvirt_gpio {
-+ struct gpio_chip gc;
-+ u32 __iomem *ts_base;
-+ /* two packed 16-bit counts of enabled and disables
-+ Allows host to detect a brief enable that was missed */
-+ u32 enables_disables[NUM_GPIO];
-+};
-+
-+static int brcmvirt_gpio_dir_in(struct gpio_chip *gc, unsigned off)
-+{
-+ struct brcmvirt_gpio *gpio;
-+ gpio = container_of(gc, struct brcmvirt_gpio, gc);
-+ return -EINVAL;
-+}
-+
-+static int brcmvirt_gpio_dir_out(struct gpio_chip *gc, unsigned off, int val)
-+{
-+ struct brcmvirt_gpio *gpio;
-+ gpio = container_of(gc, struct brcmvirt_gpio, gc);
-+ return 0;
-+}
-+
-+static int brcmvirt_gpio_get(struct gpio_chip *gc, unsigned off)
-+{
-+ struct brcmvirt_gpio *gpio;
-+ unsigned v;
-+ gpio = container_of(gc, struct brcmvirt_gpio, gc);
-+ v = readl(gpio->ts_base + off);
-+ return (v >> off) & 1;
-+}
-+
-+static void brcmvirt_gpio_set(struct gpio_chip *gc, unsigned off, int val)
-+{
-+ struct brcmvirt_gpio *gpio;
-+ u16 enables, disables;
-+ s16 diff;
-+ bool lit;
-+ gpio = container_of(gc, struct brcmvirt_gpio, gc);
-+ enables = gpio->enables_disables[off] >> 16;
-+ disables = gpio->enables_disables[off] >> 0;
-+ diff = (s16)(enables - disables);
-+ lit = diff > 0;
-+ if ((val && lit) || (!val && !lit))
-+ return;
-+ if (val)
-+ enables++;
-+ else
-+ disables++;
-+ diff = (s16)(enables - disables);
-+ BUG_ON(diff != 0 && diff != 1);
-+ gpio->enables_disables[off] = (enables << 16) | (disables << 0);
-+ writel(gpio->enables_disables[off], gpio->ts_base + off);
-+}
-+
-+static int brcmvirt_gpio_probe(struct platform_device *pdev)
-+{
-+ struct device *dev = &pdev->dev;
-+ struct device_node *np = dev->of_node;
-+ struct device_node *fw_node;
-+ struct rpi_firmware *fw;
-+ struct brcmvirt_gpio *ucb;
-+ u32 gpiovirtbuf;
-+ int err = 0;
-+
-+ fw_node = of_parse_phandle(np, "firmware", 0);
-+ if (!fw_node) {
-+ dev_err(dev, "Missing firmware node\n");
-+ return -ENOENT;
-+ }
-+
-+ fw = rpi_firmware_get(fw_node);
-+ if (!fw)
-+ return -EPROBE_DEFER;
-+
-+ err = rpi_firmware_property(fw, RPI_FIRMWARE_FRAMEBUFFER_GET_GPIOVIRTBUF,
-+ &gpiovirtbuf, sizeof(gpiovirtbuf));
-+
-+ if (err) {
-+ dev_err(dev, "Failed to get gpiovirtbuf\n");
-+ goto err;
-+ }
-+
-+ if (!gpiovirtbuf) {
-+ dev_err(dev, "No virtgpio buffer\n");
-+ err = -ENOENT;
-+ goto err;
-+ }
-+
-+ ucb = devm_kzalloc(dev, sizeof *ucb, GFP_KERNEL);
-+ if (!ucb) {
-+ err = -EINVAL;
-+ goto err;
-+ }
-+
-+ // mmap the physical memory
-+ gpiovirtbuf &= ~0xc0000000;
-+ ucb->ts_base = ioremap(gpiovirtbuf, 4096);
-+ if (ucb->ts_base == NULL) {
-+ dev_err(dev, "Failed to map physical address\n");
-+ err = -ENOENT;
-+ goto err;
-+ }
-+
-+ ucb->gc.label = MODULE_NAME;
-+ ucb->gc.owner = THIS_MODULE;
-+ ucb->gc.dev = dev;
-+ ucb->gc.of_node = np;
-+ ucb->gc.base = 100;
-+ ucb->gc.ngpio = NUM_GPIO;
-+
-+ ucb->gc.direction_input = brcmvirt_gpio_dir_in;
-+ ucb->gc.direction_output = brcmvirt_gpio_dir_out;
-+ ucb->gc.get = brcmvirt_gpio_get;
-+ ucb->gc.set = brcmvirt_gpio_set;
-+ ucb->gc.can_sleep = true;
-+
-+ err = gpiochip_add(&ucb->gc);
-+ if (err)
-+ goto err;
-+
-+ platform_set_drvdata(pdev, ucb);
-+
-+err:
-+ return err;
-+
-+}
-+
-+static int brcmvirt_gpio_remove(struct platform_device *pdev)
-+{
-+ int err = 0;
-+ struct brcmvirt_gpio *ucb = platform_get_drvdata(pdev);
-+
-+ gpiochip_remove(&ucb->gc);
-+ iounmap(ucb->ts_base);
-+ return err;
-+}
-+
-+static const struct of_device_id __maybe_unused brcmvirt_gpio_ids[] = {
-+ { .compatible = "brcm,bcm2835-virtgpio" },
-+ { }
-+};
-+MODULE_DEVICE_TABLE(of, brcmvirt_gpio_ids);
-+
-+static struct platform_driver brcmvirt_gpio_driver = {
-+ .driver = {
-+ .name = MODULE_NAME,
-+ .owner = THIS_MODULE,
-+ .of_match_table = of_match_ptr(brcmvirt_gpio_ids),
-+ },
-+ .probe = brcmvirt_gpio_probe,
-+ .remove = brcmvirt_gpio_remove,
-+};
-+module_platform_driver(brcmvirt_gpio_driver);
-+
-+MODULE_LICENSE("GPL");
-+MODULE_AUTHOR("Dom Cobley <popcornmix at gmail.com>");
-+MODULE_DESCRIPTION("brcmvirt GPIO driver");
-+MODULE_ALIAS("platform:brcmvirt-gpio");
---- a/include/soc/bcm2835/raspberrypi-firmware.h
-+++ b/include/soc/bcm2835/raspberrypi-firmware.h
-@@ -93,6 +93,7 @@ enum rpi_firmware_property_tag {
- RPI_FIRMWARE_FRAMEBUFFER_GET_OVERSCAN = 0x0004000a,
- RPI_FIRMWARE_FRAMEBUFFER_GET_PALETTE = 0x0004000b,
- RPI_FIRMWARE_FRAMEBUFFER_GET_TOUCHBUF = 0x0004000f,
-+ RPI_FIRMWARE_FRAMEBUFFER_GET_GPIOVIRTBUF = 0x00040010,
- RPI_FIRMWARE_FRAMEBUFFER_RELEASE = 0x00048001,
- RPI_FIRMWARE_FRAMEBUFFER_TEST_PHYSICAL_WIDTH_HEIGHT = 0x00044003,
- RPI_FIRMWARE_FRAMEBUFFER_TEST_VIRTUAL_WIDTH_HEIGHT = 0x00044004,
diff --git a/target/linux/brcm2708/patches-4.4/0160-BCM270X_DT-Add-Pi3-support.patch b/target/linux/brcm2708/patches-4.4/0160-BCM270X_DT-Add-Pi3-support.patch
deleted file mode 100644
index 4a4175f..0000000
--- a/target/linux/brcm2708/patches-4.4/0160-BCM270X_DT-Add-Pi3-support.patch
+++ /dev/null
@@ -1,323 +0,0 @@
-From 75b68302aff0489e1ece90d00086759cec4166c1 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Thu, 21 Jan 2016 17:57:49 +0000
-Subject: [PATCH] BCM270X_DT: Add Pi3 support
-
----
- arch/arm/boot/dts/Makefile | 1 +
- arch/arm/boot/dts/bcm2710-rpi-3-b.dts | 192 ++++++++++++++++++++++++++++++++++
- arch/arm/boot/dts/bcm2710.dtsi | 102 ++++++++++++++++++
- 3 files changed, 295 insertions(+)
- create mode 100644 arch/arm/boot/dts/bcm2710-rpi-3-b.dts
- create mode 100644 arch/arm/boot/dts/bcm2710.dtsi
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -5,6 +5,7 @@ dtb-$(CONFIG_ARCH_BCM2708) += bcm2708-rp
- dtb-$(CONFIG_ARCH_BCM2708) += bcm2708-rpi-cm.dtb
- dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-cm.dtb
- dtb-$(CONFIG_ARCH_BCM2709) += bcm2709-rpi-2-b.dtb
-+dtb-$(CONFIG_ARCH_BCM2709) += bcm2710-rpi-3-b.dtb
-
- # Raspberry Pi
- ifeq ($(CONFIG_ARCH_BCM2708),y)
---- /dev/null
-+++ b/arch/arm/boot/dts/bcm2710-rpi-3-b.dts
-@@ -0,0 +1,192 @@
-+/dts-v1/;
-+
-+#include "bcm2710.dtsi"
-+
-+/ {
-+ compatible = "brcm,bcm2710","brcm,bcm2709";
-+ model = "Raspberry Pi 3 Model B";
-+};
-+
-+&gpio {
-+ sdhost_pins: sdhost_pins {
-+ brcm,pins = <48 49 50 51 52 53>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+
-+ spi0_pins: spi0_pins {
-+ brcm,pins = <9 10 11>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+
-+ spi0_cs_pins: spi0_cs_pins {
-+ brcm,pins = <8 7>;
-+ brcm,function = <1>; /* output */
-+ };
-+
-+ i2c0_pins: i2c0 {
-+ brcm,pins = <0 1>;
-+ brcm,function = <4>;
-+ };
-+
-+ i2c1_pins: i2c1 {
-+ brcm,pins = <2 3>;
-+ brcm,function = <4>;
-+ };
-+
-+ i2s_pins: i2s {
-+ brcm,pins = <18 19 20 21>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+
-+ sdio_pins: sdio_pins {
-+ brcm,pins = <34 35 36 37 38 39>;
-+ brcm,function = <7>; // alt3 = SD1
-+ brcm,pull = <0 2 2 2 2 2>;
-+ };
-+
-+ bt_pins: bt_pins {
-+ brcm,pins = <28 29 30 31 43>;
-+ brcm,function = <6 6 6 6 4>; /* alt2:PCM alt0:GPCLK2 */
-+ brcm,pull = <0 0 0 0 0>;
-+ };
-+
-+ uart0_pins: uart0_pins {
-+ brcm,pins = <32 33>;
-+ brcm,function = <7>; /* alt3=UART0 */
-+ brcm,pull = <0 0>;
-+ };
-+
-+ uart1_pins: uart1_pins {
-+ brcm,pins = <14 15>;
-+ brcm,function = <2>; /* alt5=UART1 */
-+ brcm,pull = <0 0>;
-+ };
-+};
-+
-+&sdhost {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&sdhost_pins>;
-+ bus-width = <4>;
-+ status = "okay";
-+};
-+
-+&mmc {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&sdio_pins>;
-+ non-removable;
-+ bus-width = <4>;
-+ status = "okay";
-+ brcm,overclock-50 = <0>;
-+};
-+
-+&soc {
-+ virtgpio: virtgpio {
-+ compatible = "brcm,bcm2835-virtgpio";
-+ gpio-controller;
-+ #gpio-cells = <2>;
-+ firmware = <&firmware>;
-+ status = "okay";
-+ };
-+};
-+
-+&fb {
-+ status = "okay";
-+};
-+
-+&uart0 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&uart0_pins &bt_pins>;
-+ status = "okay";
-+};
-+
-+&uart1 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&uart1_pins>;
-+ status = "okay";
-+};
-+
-+&spi0 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
-+ cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
-+
-+ spidev at 0{
-+ compatible = "spidev";
-+ reg = <0>; /* CE0 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ };
-+
-+ spidev at 1{
-+ compatible = "spidev";
-+ reg = <1>; /* CE1 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ };
-+};
-+
-+&i2c0 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2c0_pins>;
-+ clock-frequency = <100000>;
-+};
-+
-+&i2c1 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2c1_pins>;
-+ clock-frequency = <100000>;
-+};
-+
-+&i2c2 {
-+ clock-frequency = <100000>;
-+};
-+
-+&i2s {
-+ #sound-dai-cells = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2s_pins>;
-+};
-+
-+&random {
-+ status = "okay";
-+};
-+
-+&leds {
-+ act_led: act {
-+ label = "led0";
-+ linux,default-trigger = "mmc0";
-+ gpios = <&virtgpio 0 0>;
-+ };
-+};
-+
-+/ {
-+ chosen {
-+ bootargs = "8250.nr_uarts=1";
-+ };
-+};
-+
-+/ {
-+ __overrides__ {
-+ uart0 = <&uart0>,"status";
-+ uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
-+ i2s = <&i2s>,"status";
-+ spi = <&spi0>,"status";
-+ i2c0 = <&i2c0>,"status";
-+ i2c1 = <&i2c1>,"status";
-+ i2c2_iknowwhatimdoing = <&i2c2>,"status";
-+ i2c0_baudrate = <&i2c0>,"clock-frequency:0";
-+ i2c1_baudrate = <&i2c1>,"clock-frequency:0";
-+ i2c2_baudrate = <&i2c2>,"clock-frequency:0";
-+ core_freq = <&clk_core>,"clock-frequency:0";
-+
-+ act_led_gpio = <&act_led>,"gpios:4";
-+ act_led_activelow = <&act_led>,"gpios:8";
-+ act_led_trigger = <&act_led>,"linux,default-trigger";
-+
-+ audio = <&audio>,"status";
-+ watchdog = <&watchdog>,"status";
-+ random = <&random>,"status";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/bcm2710.dtsi
-@@ -0,0 +1,102 @@
-+#include "bcm2708_common.dtsi"
-+
-+/ {
-+ compatible = "brcm,bcm2710","brcm,bcm2709";
-+ model = "BCM2710";
-+
-+ chosen {
-+ /* No padding required - the boot loader can do that. */
-+ bootargs = "";
-+ };
-+
-+ soc {
-+ ranges = <0x7e000000 0x3f000000 0x01000000>,
-+ <0x40000000 0x40000000 0x00040000>;
-+
-+ local_intc: local_intc {
-+ compatible = "brcm,bcm2836-l1-intc";
-+ reg = <0x40000000 0x100>;
-+ interrupt-controller;
-+ #interrupt-cells = <1>;
-+ interrupt-parent = <&local_intc>;
-+ };
-+
-+ arm-pmu {
-+ compatible = "arm,cortex-a7-pmu";
-+ interrupt-parent = <&local_intc>;
-+ interrupts = <9>;
-+ };
-+
-+ gpiomem {
-+ compatible = "brcm,bcm2835-gpiomem";
-+ reg = <0x7e200000 0x1000>;
-+ status = "okay";
-+ };
-+
-+ timer {
-+ compatible = "arm,armv7-timer";
-+ clock-frequency = <19200000>;
-+ interrupt-parent = <&local_intc>;
-+ interrupts = <0>, // PHYS_SECURE_PPI
-+ <1>, // PHYS_NONSECURE_PPI
-+ <3>, // VIRT_PPI
-+ <2>; // HYP_PPI
-+ always-on;
-+ };
-+
-+ syscon at 40000000 {
-+ compatible = "brcm,bcm2836-arm-local", "syscon";
-+ reg = <0x40000000 0x100>;
-+ };
-+ };
-+
-+ cpus: cpus {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ v7_cpu0: cpu at 0 {
-+ device_type = "cpu";
-+ compatible = "arm,cortex-a7";
-+ reg = <0x000>;
-+ clock-frequency = <800000000>;
-+ };
-+
-+ v7_cpu1: cpu at 1 {
-+ device_type = "cpu";
-+ compatible = "arm,cortex-a7";
-+ reg = <0x001>;
-+ clock-frequency = <800000000>;
-+ };
-+
-+ v7_cpu2: cpu at 2 {
-+ device_type = "cpu";
-+ compatible = "arm,cortex-a7";
-+ reg = <0x002>;
-+ clock-frequency = <800000000>;
-+ };
-+
-+ v7_cpu3: cpu at 3 {
-+ device_type = "cpu";
-+ compatible = "arm,cortex-a7";
-+ reg = <0x003>;
-+ clock-frequency = <800000000>;
-+ };
-+ };
-+
-+ __overrides__ {
-+ arm_freq = <&v7_cpu0>, "clock-frequency:0",
-+ <&v7_cpu1>, "clock-frequency:0",
-+ <&v7_cpu2>, "clock-frequency:0",
-+ <&v7_cpu3>, "clock-frequency:0";
-+ };
-+};
-+
-+&watchdog {
-+ status = "okay";
-+};
-+
-+&intc {
-+ compatible = "brcm,bcm2836-armctrl-ic";
-+ interrupt-parent = <&local_intc>;
-+ interrupts = <8>;
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0161-DT-Add-overlays-to-configure-I2C-pins.patch b/target/linux/brcm2708/patches-4.4/0161-DT-Add-overlays-to-configure-I2C-pins.patch
deleted file mode 100644
index eddbdf8..0000000
--- a/target/linux/brcm2708/patches-4.4/0161-DT-Add-overlays-to-configure-I2C-pins.patch
+++ /dev/null
@@ -1,134 +0,0 @@
-From ada7795b8734bd5d66ff9e7499fff148f0e17510 Mon Sep 17 00:00:00 2001
-From: Dave Stevenson <6by9 at users.noreply.github.com>
-Date: Mon, 8 Feb 2016 23:49:41 +0000
-Subject: [PATCH] DT: Add overlays to configure I2C pins
-
-Lifted from
-https://www.raspberrypi.org/forums/viewtopic.php?f=107&t=120938&p=825883
-so not claiming this to be my own work.
-Adds overlays i2c0-bcm2708 and i2c1-bcm2708 that allow the pin
-allocations for i2c-0 and i2c-1 to be changed.
----
- arch/arm/boot/dts/overlays/Makefile | 2 ++
- arch/arm/boot/dts/overlays/README | 16 ++++++++++
- .../arm/boot/dts/overlays/i2c0-bcm2708-overlay.dts | 36 +++++++++++++++++++++
- .../arm/boot/dts/overlays/i2c1-bcm2708-overlay.dts | 37 ++++++++++++++++++++++
- 4 files changed, 91 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/i2c0-bcm2708-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/i2c1-bcm2708-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -29,6 +29,8 @@ dtb-$(RPI_DT_OVERLAYS) += hy28a-overlay.
- dtb-$(RPI_DT_OVERLAYS) += hy28b-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += i2c-rtc-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += i2c-gpio-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += i2c0-bcm2708-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += i2c1-bcm2708-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += i2s-mmap-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += iqaudio-dac-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += iqaudio-dacplus-overlay.dtb
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -371,6 +371,22 @@ Params: ds1307 Select t
- pcf8563 Select the PCF8563 device
-
-
-+Name: i2c0-bcm2708
-+Info: Enable the i2c_bcm2708 driver for the i2c0 bus
-+Load: dtoverlay=i2c0-bcm2708,<param>=<val>
-+Params: sda0_pin GPIO pin for SDA0 (0, 28 [or 44] - default 0)
-+ scl0_pin GPIO pin for SCL0 (1, 29 [or 45] - default 1)
-+
-+
-+Name: i2c1-bcm2708
-+Info: Enable the i2c_bcm2708 driver for the i2c1 bus
-+Load: dtoverlay=i2c1-bcm2708,<param>=<val>
-+Params: sda1_pin GPIO pin for SDA1 (2 or 44 - default 2)
-+ scl1_pin GPIO pin for SCL1 (3 or 45 - default 3)
-+ pin_func Alternative pin function (4 (alt0), 6 (alt2) -
-+ default 4)
-+
-+
- Name: i2s-mmap
- Info: Enables mmap support in the bcm2708-i2s driver
- Load: dtoverlay=i2s-mmap
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/i2c0-bcm2708-overlay.dts
-@@ -0,0 +1,36 @@
-+/*
-+ * Device tree overlay for i2c_bcm2708, i2c0 bus
-+ *
-+ * Compile:
-+ * dtc -@ -I dts -O dtb -o i2c0-bcm2708-overlay.dtb i2c0-bcm2708-overlay.dts
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/{
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&i2c0>;
-+ __overlay__ {
-+ pinctrl-0 = <&i2c0_pins>;
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ i2c0_pins: i2c0 {
-+ brcm,pins = <0 1>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ sda0_pin = <&i2c0_pins>,"brcm,pins:0";
-+ scl0_pin = <&i2c0_pins>,"brcm,pins:4";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/i2c1-bcm2708-overlay.dts
-@@ -0,0 +1,37 @@
-+/*
-+ * Device tree overlay for i2c_bcm2708, i2c1 bus
-+ *
-+ * Compile:
-+ * dtc -@ -I dts -O dtb -o i2c1-bcm2708-overlay.dtb i2c1-bcm2708-overlay.dts
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/{
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&i2c1>;
-+ __overlay__ {
-+ pinctrl-0 = <&i2c1_pins>;
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ i2c1_pins: i2c1 {
-+ brcm,pins = <2 3>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ sda1_pin = <&i2c1_pins>,"brcm,pins:0";
-+ scl1_pin = <&i2c1_pins>,"brcm,pins:4";
-+ pin_func = <&i2c1_pins>,"brcm,function:0";
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0162-bcm2835-camera-fix-a-bug-in-computation-of-frame-tim.patch b/target/linux/brcm2708/patches-4.4/0162-bcm2835-camera-fix-a-bug-in-computation-of-frame-tim.patch
deleted file mode 100644
index f8ae31b..0000000
--- a/target/linux/brcm2708/patches-4.4/0162-bcm2835-camera-fix-a-bug-in-computation-of-frame-tim.patch
+++ /dev/null
@@ -1,22 +0,0 @@
-From fe490f6183e1a1759abe188d5e83708956c0fbbe Mon Sep 17 00:00:00 2001
-From: Dhiraj Goel <dhiraj.goel at gmail.com>
-Date: Thu, 3 Mar 2016 21:10:50 -0800
-Subject: [PATCH] bcm2835-camera: fix a bug in computation of frame timestamp
-
-Fixes #1318
----
- drivers/media/platform/bcm2835/bcm2835-camera.c | 3 +--
- 1 file changed, 1 insertion(+), 2 deletions(-)
-
---- a/drivers/media/platform/bcm2835/bcm2835-camera.c
-+++ b/drivers/media/platform/bcm2835/bcm2835-camera.c
-@@ -360,8 +360,7 @@ static void buffer_cb(struct vchiq_mmal_
- div =
- div_u64_rem(runtime_us, USEC_PER_SEC, &rem);
- buf->vb.timestamp.tv_sec =
-- dev->capture.kernel_start_ts.tv_sec - 1 +
-- div;
-+ dev->capture.kernel_start_ts.tv_sec + div;
- buf->vb.timestamp.tv_usec =
- dev->capture.kernel_start_ts.tv_usec + rem;
-
diff --git a/target/linux/brcm2708/patches-4.4/0163-BCM270X_DT-Add-pi3-disable-bt-overlay.patch b/target/linux/brcm2708/patches-4.4/0163-BCM270X_DT-Add-pi3-disable-bt-overlay.patch
deleted file mode 100644
index 092e289..0000000
--- a/target/linux/brcm2708/patches-4.4/0163-BCM270X_DT-Add-pi3-disable-bt-overlay.patch
+++ /dev/null
@@ -1,96 +0,0 @@
-From 21d5e5f19ba17eab204a1a2f77370892ebec4de9 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Wed, 2 Mar 2016 10:59:05 +0000
-Subject: [PATCH] BCM270X_DT: Add pi3-disable-bt overlay
-
-Disable Bluetooth and restore UART0/ttyAMA0 over GPIOs 14 & 15. To disable
-the systemd service that initialises the modem so it doesn't use the UART:
-
- sudo systemctl disable hciuart
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 8 ++++
- .../boot/dts/overlays/pi3-disable-bt-overlay.dts | 48 ++++++++++++++++++++++
- 3 files changed, 57 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/pi3-disable-bt-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -39,6 +39,7 @@ dtb-$(RPI_DT_OVERLAYS) += mcp2515-can0-o
- dtb-$(RPI_DT_OVERLAYS) += mcp2515-can1-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += mmc-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += mz61581-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += pi3-disable-bt-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += piscreen-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += piscreen2r-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += pitft28-capacitive-overlay.dtb
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -496,6 +496,14 @@ Params: speed Display
- [ The pcf8563-rtc overlay has been deleted. See i2c-rtc. ]
-
-
-+Name: pi3-disable-bt
-+Info: Disable Pi3 Bluetooth and restore UART0/ttyAMA0 over GPIOs 14 & 15
-+ N.B. To disable the systemd service that initialises the modem so it
-+ doesn't use the UART, use 'sudo systemctl disable hciuart'.
-+Load: dtoverlay=pi3-disable-bt
-+Params: <None>
-+
-+
- Name: piscreen
- Info: PiScreen display by OzzMaker.com
- Load: dtoverlay=piscreen,<param>=<val>
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/pi3-disable-bt-overlay.dts
-@@ -0,0 +1,48 @@
-+/dts-v1/;
-+/plugin/;
-+
-+/* Disable Bluetooth and restore UART0/ttyAMA0 over GPIOs 14 & 15.
-+ To disable the systemd service that initialises the modem so it doesn't use
-+ the UART:
-+
-+ sudo systemctl disable hciuart
-+*/
-+
-+/{
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&uart1>;
-+ __overlay__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&uart0>;
-+ __overlay__ {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&uart0_pins>;
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ uart0_pins: uart0_pins {
-+ brcm,pins = <14 15>;
-+ brcm,function = <4>; /* alt0 */
-+ brcm,pull = <0 2>;
-+ };
-+ };
-+ };
-+
-+ fragment at 3 {
-+ target-path = "/aliases";
-+ __overlay__ {
-+ serial0 = "/soc/uart at 7e201000";
-+ serial1 = "/soc/uart at 7e215040";
-+ };
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0164-BCM270X_DT-Add-pi3-miniuart-bt-DT-overlay.patch b/target/linux/brcm2708/patches-4.4/0164-BCM270X_DT-Add-pi3-miniuart-bt-DT-overlay.patch
deleted file mode 100644
index 6e705b9..0000000
--- a/target/linux/brcm2708/patches-4.4/0164-BCM270X_DT-Add-pi3-miniuart-bt-DT-overlay.patch
+++ /dev/null
@@ -1,117 +0,0 @@
-From 91c1bcac979f9633784bef027c127e95db8ac673 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 7 Mar 2016 09:53:03 +0000
-Subject: [PATCH] BCM270X_DT: Add pi3-miniuart-bt DT overlay
-
-Switch Pi3 Bluetooth function to use the mini-UART (ttyS0) and restore
-UART0/ttyAMA0 over GPIOs 14 & 15. Note that this may reduce the maximum
-usable baudrate.
-
-It is also necessary to edit /lib/systemd/system/hciuart.server and
-replace ttyAMA0 with ttyS0.
-
-If cmdline.txt uses the alias serial0 to refer to the user-accessable port
-then the firmware will replace with the appropriate port whether or not
-this overlay is used.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 10 ++++
- .../boot/dts/overlays/pi3-miniuart-bt-overlay.dts | 61 ++++++++++++++++++++++
- 3 files changed, 72 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/pi3-miniuart-bt-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -40,6 +40,7 @@ dtb-$(RPI_DT_OVERLAYS) += mcp2515-can1-o
- dtb-$(RPI_DT_OVERLAYS) += mmc-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += mz61581-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += pi3-disable-bt-overlay.dtb
-+dtb-$(RPI_DT_OVERLAYS) += pi3-miniuart-bt-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += piscreen-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += piscreen2r-overlay.dtb
- dtb-$(RPI_DT_OVERLAYS) += pitft28-capacitive-overlay.dtb
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -504,6 +504,16 @@ Load: dtoverlay=pi3-disable-bt
- Params: <None>
-
-
-+Name: pi3-miniuart-bt
-+Info: Switch Pi3 Bluetooth function to use the mini-UART (ttyS0) and restore
-+ UART0/ttyAMA0 over GPIOs 14 & 15. Note that this may reduce the maximum
-+ usable baudrate.
-+ N.B. It is also necessary to edit /lib/systemd/system/hciuart.server
-+ and replace ttyAMA0 with ttyS0.
-+Load: dtoverlay=pi3-miniuart-bt
-+Params: <None>
-+
-+
- Name: piscreen
- Info: PiScreen display by OzzMaker.com
- Load: dtoverlay=piscreen,<param>=<val>
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/pi3-miniuart-bt-overlay.dts
-@@ -0,0 +1,61 @@
-+/dts-v1/;
-+/plugin/;
-+
-+/* Switch Pi3 Bluetooth function to use the mini-UART (ttyS0) and restore
-+ UART0/ttyAMA0 over GPIOs 14 & 15. Note that this may reduce the maximum
-+ usable baudrate.
-+
-+ It is also necessary to edit /lib/systemd/system/hciuart.server and
-+ replace ttyAMA0 with ttyS0.
-+
-+ If cmdline.txt uses the alias serial0 to refer to the user-accessable port
-+ then the firmware will replace with the appropriate port whether or not
-+ this overlay is used.
-+*/
-+
-+/{
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&uart0>;
-+ __overlay__ {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&uart0_pins>;
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&uart1>;
-+ __overlay__ {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&uart1_pins>;
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ uart0_pins: uart0_pins {
-+ brcm,pins = <14 15>;
-+ brcm,function = <4>; /* alt0 */
-+ brcm,pull = <0 2>;
-+ };
-+
-+ uart1_pins: uart1_pins {
-+ brcm,pins = <32 33>;
-+ brcm,function = <2>; /* alt5=UART1 */
-+ brcm,pull = <0 0>;
-+ };
-+ };
-+ };
-+
-+ fragment at 3 {
-+ target-path = "/aliases";
-+ __overlay__ {
-+ serial0 = "/soc/uart at 7e201000";
-+ serial1 = "/soc/uart at 7e215040";
-+ };
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0165-Pi3-DT-Add-dtparams-for-the-SD-interface.patch b/target/linux/brcm2708/patches-4.4/0165-Pi3-DT-Add-dtparams-for-the-SD-interface.patch
deleted file mode 100644
index f852290..0000000
--- a/target/linux/brcm2708/patches-4.4/0165-Pi3-DT-Add-dtparams-for-the-SD-interface.patch
+++ /dev/null
@@ -1,25 +0,0 @@
-From db0517a83136007b585e3d73800b5798cc2e3941 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 7 Mar 2016 13:38:39 +0000
-Subject: [PATCH] Pi3 DT: Add dtparams for the SD interface
-
-Add new base dtparams sd_overclock, sd_force_pio, sd_pio_limit
-and sd_debug. These were missed out of the initial Pi3 DTB.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/bcm2710-rpi-3-b.dts | 4 ++++
- 1 file changed, 4 insertions(+)
-
---- a/arch/arm/boot/dts/bcm2710-rpi-3-b.dts
-+++ b/arch/arm/boot/dts/bcm2710-rpi-3-b.dts
-@@ -188,5 +188,9 @@
- audio = <&audio>,"status";
- watchdog = <&watchdog>,"status";
- random = <&random>,"status";
-+ sd_overclock = <&sdhost>,"brcm,overclock-50:0";
-+ sd_force_pio = <&sdhost>,"brcm,force-pio?";
-+ sd_pio_limit = <&sdhost>,"brcm,pio-limit:0";
-+ sd_debug = <&sdhost>,"brcm,debug";
- };
- };
diff --git a/target/linux/brcm2708/patches-4.4/0166-vchiq_arm-Tweak-the-logging-output.patch b/target/linux/brcm2708/patches-4.4/0166-vchiq_arm-Tweak-the-logging-output.patch
deleted file mode 100644
index 024d792..0000000
--- a/target/linux/brcm2708/patches-4.4/0166-vchiq_arm-Tweak-the-logging-output.patch
+++ /dev/null
@@ -1,75 +0,0 @@
-From 1c501f26df2c902003b237fea2570e251239436e Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 7 Mar 2016 15:05:11 +0000
-Subject: [PATCH] vchiq_arm: Tweak the logging output
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- .../vc04_services/interface/vchiq_arm/vchiq_core.c | 31 +++++++++-------------
- 1 file changed, 13 insertions(+), 18 deletions(-)
-
---- a/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_core.c
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_core.c
-@@ -891,16 +891,14 @@ queue_message(VCHIQ_STATE_T *state, VCHI
- error_count);
- return VCHIQ_ERROR;
- }
-- if (i == 0) {
-- if (SRVTRACE_ENABLED(service,
-- VCHIQ_LOG_INFO))
-- vchiq_log_dump_mem("Sent", 0,
-- header->data + pos,
-- min(64u,
-- elements[0].size));
-- }
- }
-
-+ if (SRVTRACE_ENABLED(service,
-+ VCHIQ_LOG_INFO))
-+ vchiq_log_dump_mem("Sent", 0,
-+ header->data,
-+ min(16, pos));
-+
- spin_lock("a_spinlock);
- service_quota->message_use_count++;
-
-@@ -1039,16 +1037,13 @@ queue_message_sync(VCHIQ_STATE_T *state,
- error_count);
- return VCHIQ_ERROR;
- }
-- if (i == 0) {
-- if (vchiq_sync_log_level >=
-- VCHIQ_LOG_TRACE)
-- vchiq_log_dump_mem("Sent Sync",
-- 0, header->data + pos,
-- min(64u,
-- elements[0].size));
-- }
- }
-
-+ if (vchiq_sync_log_level >= VCHIQ_LOG_TRACE)
-+ vchiq_log_dump_mem("Sent Sync",
-+ 0, header->data,
-+ min(16, pos));
-+
- VCHIQ_SERVICE_STATS_INC(service, ctrl_tx_count);
- VCHIQ_SERVICE_STATS_ADD(service, ctrl_tx_bytes, size);
- } else {
-@@ -1720,7 +1715,7 @@ parse_rx_slots(VCHIQ_STATE_T *state)
- remoteport, localport, size);
- if (size > 0)
- vchiq_log_dump_mem("Rcvd", 0, header->data,
-- min(64, size));
-+ min(16, size));
- }
-
- if (((unsigned int)header & VCHIQ_SLOT_MASK) + calc_stride(size)
-@@ -2187,7 +2182,7 @@ sync_func(void *v)
- remoteport, localport, size);
- if (size > 0)
- vchiq_log_dump_mem("Rcvd", 0, header->data,
-- min(64, size));
-+ min(16, size));
- }
-
- switch (type) {
diff --git a/target/linux/brcm2708/patches-4.4/0167-bcm2835-sdhost-Only-claim-one-DMA-channel.patch b/target/linux/brcm2708/patches-4.4/0167-bcm2835-sdhost-Only-claim-one-DMA-channel.patch
deleted file mode 100644
index 945c972..0000000
--- a/target/linux/brcm2708/patches-4.4/0167-bcm2835-sdhost-Only-claim-one-DMA-channel.patch
+++ /dev/null
@@ -1,160 +0,0 @@
-From 99864da2b792c10fb95f8c4f56c0a1be376a7f0d Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 7 Mar 2016 16:46:39 +0000
-Subject: [PATCH] bcm2835-sdhost: Only claim one DMA channel
-
-With both MMC controllers enabled there are few DMA channels left. The
-bcm2835-sdhost driver only uses DMA in one direction at a time, so it
-doesn't need to claim two channels.
-
-See: https://github.com/raspberrypi/linux/issues/1327
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/bcm2708_common.dtsi | 5 +--
- drivers/mmc/host/bcm2835-sdhost.c | 70 ++++++++++++++++++++++++-----------
- 2 files changed, 50 insertions(+), 25 deletions(-)
-
---- a/arch/arm/boot/dts/bcm2708_common.dtsi
-+++ b/arch/arm/boot/dts/bcm2708_common.dtsi
-@@ -136,9 +136,8 @@
- reg = <0x7e202000 0x100>;
- interrupts = <2 24>;
- clocks = <&clk_core>;
-- dmas = <&dma 13>,
-- <&dma 13>;
-- dma-names = "tx", "rx";
-+ dmas = <&dma 13>;
-+ dma-names = "rx-tx";
- brcm,overclock-50 = <0>;
- brcm,pio-limit = <1>;
- status = "disabled";
---- a/drivers/mmc/host/bcm2835-sdhost.c
-+++ b/drivers/mmc/host/bcm2835-sdhost.c
-@@ -185,9 +185,10 @@ struct bcm2835_host {
- unsigned int debug:1; /* Enable debug output */
-
- /*DMA part*/
-- struct dma_chan *dma_chan_rx; /* DMA channel for reads */
-- struct dma_chan *dma_chan_tx; /* DMA channel for writes */
-- struct dma_chan *dma_chan; /* Channel in used */
-+ struct dma_chan *dma_chan_rxtx; /* DMA channel for reads and writes */
-+ struct dma_chan *dma_chan; /* Channel in use */
-+ struct dma_slave_config dma_cfg_rx;
-+ struct dma_slave_config dma_cfg_tx;
- struct dma_async_tx_descriptor *dma_desc;
- u32 dma_dir;
- u32 drain_words;
-@@ -771,12 +772,11 @@ static void bcm2835_sdhost_prepare_dma(s
- log_event("PRD<", (u32)data, 0);
- pr_debug("bcm2835_sdhost_prepare_dma()\n");
-
-+ dma_chan = host->dma_chan_rxtx;
- if (data->flags & MMC_DATA_READ) {
-- dma_chan = host->dma_chan_rx;
- dir_data = DMA_FROM_DEVICE;
- dir_slave = DMA_DEV_TO_MEM;
- } else {
-- dma_chan = host->dma_chan_tx;
- dir_data = DMA_TO_DEVICE;
- dir_slave = DMA_MEM_TO_DEV;
- }
-@@ -813,6 +813,12 @@ static void bcm2835_sdhost_prepare_dma(s
- host->drain_words = len/4;
- }
-
-+ /* The parameters have already been validated, so this will not fail */
-+ (void)dmaengine_slave_config(dma_chan,
-+ (dir_data == DMA_FROM_DEVICE) ?
-+ &host->dma_cfg_rx :
-+ &host->dma_cfg_tx);
-+
- len = dma_map_sg(dma_chan->device->dev, data->sg, data->sg_len,
- dir_data);
-
-@@ -1805,28 +1811,46 @@ int bcm2835_sdhost_add_host(struct bcm28
- spin_lock_init(&host->lock);
-
- if (host->allow_dma) {
-- if (IS_ERR_OR_NULL(host->dma_chan_tx) ||
-- IS_ERR_OR_NULL(host->dma_chan_rx)) {
-- pr_err("%s: unable to initialise DMA channels. "
-+ if (IS_ERR_OR_NULL(host->dma_chan_rxtx)) {
-+ pr_err("%s: unable to initialise DMA channel. "
- "Falling back to PIO\n",
- mmc_hostname(mmc));
- host->use_dma = false;
- } else {
-- host->use_dma = true;
--
- cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
- cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
- cfg.slave_id = 13; /* DREQ channel */
-
-+ /* Validate the slave configurations */
-+
- cfg.direction = DMA_MEM_TO_DEV;
- cfg.src_addr = 0;
- cfg.dst_addr = host->bus_addr + SDDATA;
-- ret = dmaengine_slave_config(host->dma_chan_tx, &cfg);
-
-- cfg.direction = DMA_DEV_TO_MEM;
-- cfg.src_addr = host->bus_addr + SDDATA;
-- cfg.dst_addr = 0;
-- ret = dmaengine_slave_config(host->dma_chan_rx, &cfg);
-+ ret = dmaengine_slave_config(host->dma_chan_rxtx, &cfg);
-+
-+ if (ret == 0) {
-+ host->dma_cfg_tx = cfg;
-+
-+ cfg.direction = DMA_DEV_TO_MEM;
-+ cfg.src_addr = host->bus_addr + SDDATA;
-+ cfg.dst_addr = 0;
-+
-+ ret = dmaengine_slave_config(host->dma_chan_rxtx, &cfg);
-+ }
-+
-+ if (ret == 0) {
-+ host->dma_cfg_rx = cfg;
-+
-+ host->use_dma = true;
-+ } else {
-+ pr_err("%s: unable to configure DMA channel. "
-+ "Falling back to PIO\n",
-+ mmc_hostname(mmc));
-+ dma_release_channel(host->dma_chan_rxtx);
-+ host->dma_chan_rxtx = NULL;
-+ host->use_dma = false;
-+ }
- }
- } else {
- host->use_dma = false;
-@@ -1948,19 +1972,21 @@ static int bcm2835_sdhost_probe(struct p
-
- if (host->allow_dma) {
- if (node) {
-- host->dma_chan_tx =
-- dma_request_slave_channel(dev, "tx");
-- host->dma_chan_rx =
-- dma_request_slave_channel(dev, "rx");
-+ host->dma_chan_rxtx =
-+ dma_request_slave_channel(dev, "rx-tx");
-+ if (!host->dma_chan_rxtx)
-+ host->dma_chan_rxtx =
-+ dma_request_slave_channel(dev, "tx");
-+ if (!host->dma_chan_rxtx)
-+ host->dma_chan_rxtx =
-+ dma_request_slave_channel(dev, "rx");
- } else {
- dma_cap_mask_t mask;
-
- dma_cap_zero(mask);
- /* we don't care about the channel, any would work */
- dma_cap_set(DMA_SLAVE, mask);
-- host->dma_chan_tx =
-- dma_request_channel(mask, NULL, NULL);
-- host->dma_chan_rx =
-+ host->dma_chan_rxtx =
- dma_request_channel(mask, NULL, NULL);
- }
- }
diff --git a/target/linux/brcm2708/patches-4.4/0168-bcm2835-mmc-Only-claim-one-DMA-channel.patch b/target/linux/brcm2708/patches-4.4/0168-bcm2835-mmc-Only-claim-one-DMA-channel.patch
deleted file mode 100644
index c4f5f8f..0000000
--- a/target/linux/brcm2708/patches-4.4/0168-bcm2835-mmc-Only-claim-one-DMA-channel.patch
+++ /dev/null
@@ -1,170 +0,0 @@
-From 73271a952afe1a9ba51421478e69e95d5993e65b Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Tue, 8 Mar 2016 09:49:16 +0000
-Subject: [PATCH] bcm2835-mmc: Only claim one DMA channel
-
-With both MMC controllers enabled there are few DMA channels left. The
-bcm2835-mmc driver only uses DMA in one direction at a time, so it
-doesn't need to claim two channels.
-
-See: https://github.com/raspberrypi/linux/issues/1327
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/bcm2708_common.dtsi | 5 +--
- drivers/mmc/host/bcm2835-mmc.c | 69 +++++++++++++++++++++++++----------
- 2 files changed, 51 insertions(+), 23 deletions(-)
-
---- a/arch/arm/boot/dts/bcm2708_common.dtsi
-+++ b/arch/arm/boot/dts/bcm2708_common.dtsi
-@@ -232,9 +232,8 @@
- reg = <0x7e300000 0x100>;
- interrupts = <2 30>;
- clocks = <&clk_mmc>;
-- dmas = <&dma 11>,
-- <&dma 11>;
-- dma-names = "tx", "rx";
-+ dmas = <&dma 11>;
-+ dma-names = "rx-tx";
- brcm,overclock-50 = <0>;
- status = "disabled";
- };
---- a/drivers/mmc/host/bcm2835-mmc.c
-+++ b/drivers/mmc/host/bcm2835-mmc.c
-@@ -108,8 +108,9 @@ struct bcm2835_host {
- u32 shadow;
-
- /*DMA part*/
-- struct dma_chan *dma_chan_rx; /* DMA channel for reads */
-- struct dma_chan *dma_chan_tx; /* DMA channel for writes */
-+ struct dma_chan *dma_chan_rxtx; /* DMA channel for reads and writes */
-+ struct dma_slave_config dma_cfg_rx;
-+ struct dma_slave_config dma_cfg_tx;
- struct dma_async_tx_descriptor *tx_desc; /* descriptor */
-
- bool have_dma;
-@@ -342,7 +343,7 @@ static void bcm2835_mmc_dma_complete(voi
-
- if (host->data && !(host->data->flags & MMC_DATA_WRITE)) {
- /* otherwise handled in SDHCI IRQ */
-- dma_chan = host->dma_chan_rx;
-+ dma_chan = host->dma_chan_rxtx;
- dir_data = DMA_FROM_DEVICE;
-
- dma_unmap_sg(dma_chan->device->dev,
-@@ -493,16 +494,21 @@ static void bcm2835_mmc_transfer_dma(str
- if (host->blocks == 0)
- return;
-
-+ dma_chan = host->dma_chan_rxtx;
- if (host->data->flags & MMC_DATA_READ) {
-- dma_chan = host->dma_chan_rx;
- dir_data = DMA_FROM_DEVICE;
- dir_slave = DMA_DEV_TO_MEM;
- } else {
-- dma_chan = host->dma_chan_tx;
- dir_data = DMA_TO_DEVICE;
- dir_slave = DMA_MEM_TO_DEV;
- }
-
-+ /* The parameters have already been validated, so this will not fail */
-+ (void)dmaengine_slave_config(dma_chan,
-+ (dir_data == DMA_FROM_DEVICE) ?
-+ &host->dma_cfg_rx :
-+ &host->dma_cfg_tx);
-+
- BUG_ON(!dma_chan->device);
- BUG_ON(!dma_chan->device->dev);
- BUG_ON(!host->data->sg);
-@@ -936,7 +942,7 @@ static void bcm2835_mmc_data_irq(struct
- if (host->data->flags & MMC_DATA_WRITE) {
- /* IRQ handled here */
-
-- dma_chan = host->dma_chan_tx;
-+ dma_chan = host->dma_chan_rxtx;
- dir_data = DMA_TO_DEVICE;
- dma_unmap_sg(dma_chan->device->dev,
- host->data->sg, host->data->sg_len,
-@@ -1316,28 +1322,47 @@ static int bcm2835_mmc_add_host(struct b
- dev_info(dev, "Forcing PIO mode\n");
- host->have_dma = false;
- #else
-- if (IS_ERR_OR_NULL(host->dma_chan_tx) ||
-- IS_ERR_OR_NULL(host->dma_chan_rx)) {
-- dev_err(dev, "%s: Unable to initialise DMA channels. Falling back to PIO\n",
-+ if (IS_ERR_OR_NULL(host->dma_chan_rxtx)) {
-+ dev_err(dev, "%s: Unable to initialise DMA channel. Falling back to PIO\n",
- DRIVER_NAME);
- host->have_dma = false;
- } else {
-- dev_info(dev, "DMA channels allocated");
-- host->have_dma = true;
-+ dev_info(dev, "DMA channel allocated");
-
- cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
- cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
- cfg.slave_id = 11; /* DREQ channel */
-
-+ /* Validate the slave configurations */
-+
- cfg.direction = DMA_MEM_TO_DEV;
- cfg.src_addr = 0;
- cfg.dst_addr = host->bus_addr + SDHCI_BUFFER;
-- ret = dmaengine_slave_config(host->dma_chan_tx, &cfg);
-
-- cfg.direction = DMA_DEV_TO_MEM;
-- cfg.src_addr = host->bus_addr + SDHCI_BUFFER;
-- cfg.dst_addr = 0;
-- ret = dmaengine_slave_config(host->dma_chan_rx, &cfg);
-+ ret = dmaengine_slave_config(host->dma_chan_rxtx, &cfg);
-+
-+ if (ret == 0) {
-+ host->dma_cfg_tx = cfg;
-+
-+ cfg.direction = DMA_DEV_TO_MEM;
-+ cfg.src_addr = host->bus_addr + SDHCI_BUFFER;
-+ cfg.dst_addr = 0;
-+
-+ ret = dmaengine_slave_config(host->dma_chan_rxtx, &cfg);
-+ }
-+
-+ if (ret == 0) {
-+ host->dma_cfg_rx = cfg;
-+
-+ host->use_dma = true;
-+ } else {
-+ pr_err("%s: unable to configure DMA channel. "
-+ "Faling back to PIO\n",
-+ mmc_hostname(mmc));
-+ dma_release_channel(host->dma_chan_rxtx);
-+ host->dma_chan_rxtx = NULL;
-+ host->use_dma = false;
-+ }
- }
- #endif
- mmc->max_segs = 128;
-@@ -1416,16 +1441,20 @@ static int bcm2835_mmc_probe(struct plat
-
- #ifndef FORCE_PIO
- if (node) {
-- host->dma_chan_tx = dma_request_slave_channel(dev, "tx");
-- host->dma_chan_rx = dma_request_slave_channel(dev, "rx");
-+ host->dma_chan_rxtx = dma_request_slave_channel(dev, "rx-tx");
-+ if (!host->dma_chan_rxtx)
-+ host->dma_chan_rxtx =
-+ dma_request_slave_channel(dev, "tx");
-+ if (!host->dma_chan_rxtx)
-+ host->dma_chan_rxtx =
-+ dma_request_slave_channel(dev, "rx");
- } else {
- dma_cap_mask_t mask;
-
- dma_cap_zero(mask);
- /* we don't care about the channel, any would work */
- dma_cap_set(DMA_SLAVE, mask);
-- host->dma_chan_tx = dma_request_channel(mask, NULL, NULL);
-- host->dma_chan_rx = dma_request_channel(mask, NULL, NULL);
-+ host->dma_chan_rxtx = dma_request_channel(mask, NULL, NULL);
- }
- #endif
- clk = devm_clk_get(dev, NULL);
diff --git a/target/linux/brcm2708/patches-4.4/0169-config-rebuild-with-savedefconfig.patch b/target/linux/brcm2708/patches-4.4/0169-config-rebuild-with-savedefconfig.patch
deleted file mode 100644
index 288aa5d..0000000
--- a/target/linux/brcm2708/patches-4.4/0169-config-rebuild-with-savedefconfig.patch
+++ /dev/null
@@ -1,28 +0,0 @@
-From 82668cb6c9b2ffbe57377667c24f58effd2e4d4e Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Tue, 8 Mar 2016 17:08:39 +0000
-Subject: [PATCH] config: rebuild with savedefconfig
-
----
- arch/arm/configs/bcm2709_defconfig | 3 +--
- 1 file changed, 1 insertion(+), 2 deletions(-)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -593,7 +593,6 @@ CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
- CONFIG_SERIAL_OF_PLATFORM=y
- CONFIG_TTY_PRINTK=y
- CONFIG_HW_RANDOM=y
--CONFIG_HW_RANDOM_BCM2835=y
- CONFIG_RAW_DRIVER=y
- CONFIG_I2C=y
- CONFIG_I2C_CHARDEV=m
-@@ -1112,7 +1111,7 @@ CONFIG_EXTCON=m
- CONFIG_EXTCON_ARIZONA=m
- CONFIG_IIO=m
- CONFIG_IIO_BUFFER=y
--CONFIG_IIO_BUFFER_CB=y
-+CONFIG_IIO_BUFFER_CB=m
- CONFIG_IIO_KFIFO_BUF=m
- CONFIG_MCP320X=m
- CONFIG_DHT11=m
diff --git a/target/linux/brcm2708/patches-4.4/0170-config-Add-module-for-mcp3422-ADC.patch b/target/linux/brcm2708/patches-4.4/0170-config-Add-module-for-mcp3422-ADC.patch
deleted file mode 100644
index e9aca91..0000000
--- a/target/linux/brcm2708/patches-4.4/0170-config-Add-module-for-mcp3422-ADC.patch
+++ /dev/null
@@ -1,30 +0,0 @@
-From e354ef4c50668092dd17982005592032cc12bc14 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Tue, 8 Mar 2016 17:06:33 +0000
-Subject: [PATCH] config: Add module for mcp3422 ADC
-
----
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 2 files changed, 2 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -1114,6 +1114,7 @@ CONFIG_IIO_BUFFER=y
- CONFIG_IIO_BUFFER_CB=m
- CONFIG_IIO_KFIFO_BUF=m
- CONFIG_MCP320X=m
-+CONFIG_MCP3422=m
- CONFIG_DHT11=m
- CONFIG_PWM_BCM2835=m
- CONFIG_RASPBERRYPI_FIRMWARE=y
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -1121,6 +1121,7 @@ CONFIG_IIO_BUFFER=y
- CONFIG_IIO_BUFFER_CB=m
- CONFIG_IIO_KFIFO_BUF=m
- CONFIG_MCP320X=m
-+CONFIG_MCP3422=m
- CONFIG_DHT11=m
- CONFIG_PWM_BCM2835=m
- CONFIG_RASPBERRYPI_FIRMWARE=y
diff --git a/target/linux/brcm2708/patches-4.4/0171-Pi3-DT-Add-pull-ups-on-the-UART-RX-lines.patch b/target/linux/brcm2708/patches-4.4/0171-Pi3-DT-Add-pull-ups-on-the-UART-RX-lines.patch
deleted file mode 100644
index 3eae04c..0000000
--- a/target/linux/brcm2708/patches-4.4/0171-Pi3-DT-Add-pull-ups-on-the-UART-RX-lines.patch
+++ /dev/null
@@ -1,40 +0,0 @@
-From bd9a33f0530d2428e96e868d3e0d264f7a822105 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Tue, 8 Mar 2016 16:18:57 +0000
-Subject: [PATCH] Pi3 DT: Add pull-ups on the UART RX lines
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/bcm2710-rpi-3-b.dts | 4 ++--
- arch/arm/boot/dts/overlays/pi3-miniuart-bt-overlay.dts | 2 +-
- 2 files changed, 3 insertions(+), 3 deletions(-)
-
---- a/arch/arm/boot/dts/bcm2710-rpi-3-b.dts
-+++ b/arch/arm/boot/dts/bcm2710-rpi-3-b.dts
-@@ -53,13 +53,13 @@
- uart0_pins: uart0_pins {
- brcm,pins = <32 33>;
- brcm,function = <7>; /* alt3=UART0 */
-- brcm,pull = <0 0>;
-+ brcm,pull = <0 2>;
- };
-
- uart1_pins: uart1_pins {
- brcm,pins = <14 15>;
- brcm,function = <2>; /* alt5=UART1 */
-- brcm,pull = <0 0>;
-+ brcm,pull = <0 2>;
- };
- };
-
---- a/arch/arm/boot/dts/overlays/pi3-miniuart-bt-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/pi3-miniuart-bt-overlay.dts
-@@ -46,7 +46,7 @@
- uart1_pins: uart1_pins {
- brcm,pins = <32 33>;
- brcm,function = <2>; /* alt5=UART1 */
-- brcm,pull = <0 0>;
-+ brcm,pull = <0 2>;
- };
- };
- };
diff --git a/target/linux/brcm2708/patches-4.4/0173-BCM270X_DT-rpi-display-overlay-add-swapxy-param.patch b/target/linux/brcm2708/patches-4.4/0173-BCM270X_DT-rpi-display-overlay-add-swapxy-param.patch
deleted file mode 100644
index a80bb13..0000000
--- a/target/linux/brcm2708/patches-4.4/0173-BCM270X_DT-rpi-display-overlay-add-swapxy-param.patch
+++ /dev/null
@@ -1,38 +0,0 @@
-From a0a0ba8755deac2a3f34bce1d9a7f667856d9550 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Wed, 9 Mar 2016 21:28:52 +0000
-Subject: [PATCH] BCM270X_DT: rpi-display overlay - add swapxy param
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/overlays/README | 5 +----
- arch/arm/boot/dts/overlays/rpi-display-overlay.dts | 1 +
- 2 files changed, 2 insertions(+), 4 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -644,14 +644,11 @@ Name: rpi-display
- Info: RPi-Display - 2.8" Touch Display by Watterott
- Load: dtoverlay=rpi-display,<param>=<val>
- Params: speed Display SPI bus speed
--
- rotate Display rotation {0,90,180,270}
--
- fps Delay between frame updates
--
- debug Debug output level {0-7}
--
- xohms Touchpanel sensitivity (X-plate resistance)
-+ swapxy Swap x and y axis
-
-
- Name: rpi-ft5406
---- a/arch/arm/boot/dts/overlays/rpi-display-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/rpi-display-overlay.dts
-@@ -78,5 +78,6 @@
- fps = <&rpidisplay>,"fps:0";
- debug = <&rpidisplay>,"debug:0";
- xohms = <&rpidisplay_ts>,"ti,x-plate-ohms;0";
-+ swapxy = <&rpidisplay_ts>,"ti,swap-xy?";
- };
- };
diff --git a/target/linux/brcm2708/patches-4.4/0174-Remove-I2S-config-from-bt_pins.patch b/target/linux/brcm2708/patches-4.4/0174-Remove-I2S-config-from-bt_pins.patch
deleted file mode 100644
index eb32cc0..0000000
--- a/target/linux/brcm2708/patches-4.4/0174-Remove-I2S-config-from-bt_pins.patch
+++ /dev/null
@@ -1,38 +0,0 @@
-From e281d1ab5060498de591dc55af4742f990c3ce16 Mon Sep 17 00:00:00 2001
-From: DigitalDreamtime <clive.messer at digitaldreamtime.co.uk>
-Date: Fri, 11 Mar 2016 11:44:35 +0000
-Subject: [PATCH] Remove I2S config from bt_pins.
-
-Remove I2S config from bt_pins. Causes issues with clock alignment when I2S is
-used by an external DAC via GPIO header.
----
- arch/arm/boot/dts/bcm2710-rpi-3-b.dts | 6 +++---
- arch/arm/boot/dts/overlays/pi3-miniuart-bt-overlay.dts | 2 +-
- 2 files changed, 4 insertions(+), 4 deletions(-)
-
---- a/arch/arm/boot/dts/bcm2710-rpi-3-b.dts
-+++ b/arch/arm/boot/dts/bcm2710-rpi-3-b.dts
-@@ -45,9 +45,9 @@
- };
-
- bt_pins: bt_pins {
-- brcm,pins = <28 29 30 31 43>;
-- brcm,function = <6 6 6 6 4>; /* alt2:PCM alt0:GPCLK2 */
-- brcm,pull = <0 0 0 0 0>;
-+ brcm,pins = <43>;
-+ brcm,function = <4>; /* alt0:GPCLK2 */
-+ brcm,pull = <0>;
- };
-
- uart0_pins: uart0_pins {
---- a/arch/arm/boot/dts/overlays/pi3-miniuart-bt-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/pi3-miniuart-bt-overlay.dts
-@@ -29,7 +29,7 @@
- target = <&uart1>;
- __overlay__ {
- pinctrl-names = "default";
-- pinctrl-0 = <&uart1_pins>;
-+ pinctrl-0 = <&uart1_pins &bt_pins>;
- status = "okay";
- };
- };
diff --git a/target/linux/brcm2708/patches-4.4/0175-Revert-scripts-dtc-Add-overlay-support.patch b/target/linux/brcm2708/patches-4.4/0175-Revert-scripts-dtc-Add-overlay-support.patch
deleted file mode 100644
index cc9cc7d..0000000
--- a/target/linux/brcm2708/patches-4.4/0175-Revert-scripts-dtc-Add-overlay-support.patch
+++ /dev/null
@@ -1,4390 +0,0 @@
-From eab82be4e9c0a7267a0535a79740e81bc797e65d Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 10 Aug 2015 09:44:59 +0100
-Subject: [PATCH] Revert "scripts/dtc: Add overlay support"
-
-This reverts commit fa6d1755c2fdd9451077d8248e3804f0619f19b9.
----
- scripts/dtc/checks.c | 119 +--
- scripts/dtc/dtc-lexer.l | 5 -
- scripts/dtc/dtc-lexer.lex.c_shipped | 490 +++++----
- scripts/dtc/dtc-parser.tab.c_shipped | 1896 +++++++++++++++-------------------
- scripts/dtc/dtc-parser.tab.h_shipped | 107 +-
- scripts/dtc/dtc-parser.y | 23 +-
- scripts/dtc/dtc.c | 9 +-
- scripts/dtc/dtc.h | 38 -
- scripts/dtc/flattree.c | 141 +--
- scripts/dtc/version_gen.h | 2 +-
- 10 files changed, 1145 insertions(+), 1685 deletions(-)
-
---- a/scripts/dtc/checks.c
-+++ b/scripts/dtc/checks.c
-@@ -458,91 +458,21 @@ static void fixup_phandle_references(str
- struct node *node, struct property *prop)
- {
- struct marker *m = prop->val.markers;
-- struct fixup *f, **fp;
-- struct fixup_entry *fe, **fep;
- struct node *refnode;
- cell_t phandle;
-- int has_phandle_refs;
--
-- has_phandle_refs = 0;
-- for_each_marker_of_type(m, REF_PHANDLE) {
-- has_phandle_refs = 1;
-- break;
-- }
--
-- if (!has_phandle_refs)
-- return;
-
- for_each_marker_of_type(m, REF_PHANDLE) {
- assert(m->offset + sizeof(cell_t) <= prop->val.len);
-
- refnode = get_node_by_ref(dt, m->ref);
-- if (!refnode && !symbol_fixup_support) {
-+ if (! refnode) {
- FAIL(c, "Reference to non-existent node or label \"%s\"\n",
-- m->ref);
-+ m->ref);
- continue;
- }
-
-- if (!refnode) {
-- /* allocate fixup entry */
-- fe = xmalloc(sizeof(*fe));
--
-- fe->node = node;
-- fe->prop = prop;
-- fe->offset = m->offset;
-- fe->next = NULL;
--
-- /* search for an already existing fixup */
-- for_each_fixup(dt, f)
-- if (strcmp(f->ref, m->ref) == 0)
-- break;
--
-- /* no fixup found, add new */
-- if (f == NULL) {
-- f = xmalloc(sizeof(*f));
-- f->ref = m->ref;
-- f->entries = NULL;
-- f->next = NULL;
--
-- /* add it to the tree */
-- fp = &dt->fixups;
-- while (*fp)
-- fp = &(*fp)->next;
-- *fp = f;
-- }
--
-- /* and now append fixup entry */
-- fep = &f->entries;
-- while (*fep)
-- fep = &(*fep)->next;
-- *fep = fe;
--
-- /* mark the entry as unresolved */
-- phandle = 0xdeadbeef;
-- } else {
-- phandle = get_node_phandle(dt, refnode);
--
-- /* if it's a plugin, we need to record it */
-- if (symbol_fixup_support && dt->is_plugin) {
--
-- /* allocate a new local fixup entry */
-- fe = xmalloc(sizeof(*fe));
--
-- fe->node = node;
-- fe->prop = prop;
-- fe->offset = m->offset;
-- fe->next = NULL;
--
-- /* append it to the local fixups */
-- fep = &dt->local_fixups;
-- while (*fep)
-- fep = &(*fep)->next;
-- *fep = fe;
-- }
-- }
--
-- *((cell_t *)(prop->val.val + m->offset)) =
-- cpu_to_fdt32(phandle);
-+ phandle = get_node_phandle(dt, refnode);
-+ *((cell_t *)(prop->val.val + m->offset)) = cpu_to_fdt32(phandle);
- }
- }
- ERROR(phandle_references, NULL, NULL, fixup_phandle_references, NULL,
-@@ -722,45 +652,6 @@ static void check_obsolete_chosen_interr
- }
- TREE_WARNING(obsolete_chosen_interrupt_controller, NULL);
-
--static void check_auto_label_phandles(struct check *c, struct node *dt,
-- struct node *node)
--{
-- struct label *l;
-- struct symbol *s, **sp;
-- int has_label;
--
-- if (!symbol_fixup_support)
-- return;
--
-- has_label = 0;
-- for_each_label(node->labels, l) {
-- has_label = 1;
-- break;
-- }
--
-- if (!has_label)
-- return;
--
-- /* force allocation of a phandle for this node */
-- (void)get_node_phandle(dt, node);
--
-- /* add the symbol */
-- for_each_label(node->labels, l) {
--
-- s = xmalloc(sizeof(*s));
-- s->label = l;
-- s->node = node;
-- s->next = NULL;
--
-- /* add it to the symbols list */
-- sp = &dt->symbols;
-- while (*sp)
-- sp = &((*sp)->next);
-- *sp = s;
-- }
--}
--NODE_WARNING(auto_label_phandles, NULL);
--
- static struct check *check_table[] = {
- &duplicate_node_names, &duplicate_property_names,
- &node_name_chars, &node_name_format, &property_name_chars,
-@@ -779,8 +670,6 @@ static struct check *check_table[] = {
- &avoid_default_addr_size,
- &obsolete_chosen_interrupt_controller,
-
-- &auto_label_phandles,
--
- &always_fail,
- };
-
---- a/scripts/dtc/dtc-lexer.l
-+++ b/scripts/dtc/dtc-lexer.l
-@@ -113,11 +113,6 @@ static void lexical_error(const char *fm
- return DT_V1;
- }
-
--<*>"/plugin/" {
-- DPRINT("Keyword: /plugin/\n");
-- return DT_PLUGIN;
-- }
--
- <*>"/memreserve/" {
- DPRINT("Keyword: /memreserve/\n");
- BEGIN_DEFAULT();
---- a/scripts/dtc/dtc-lexer.lex.c_shipped
-+++ b/scripts/dtc/dtc-lexer.lex.c_shipped
-@@ -9,7 +9,7 @@
- #define FLEX_SCANNER
- #define YY_FLEX_MAJOR_VERSION 2
- #define YY_FLEX_MINOR_VERSION 5
--#define YY_FLEX_SUBMINOR_VERSION 35
-+#define YY_FLEX_SUBMINOR_VERSION 39
- #if YY_FLEX_SUBMINOR_VERSION > 0
- #define FLEX_BETA
- #endif
-@@ -162,7 +162,12 @@ typedef unsigned int flex_uint32_t;
- typedef struct yy_buffer_state *YY_BUFFER_STATE;
- #endif
-
--extern int yyleng;
-+#ifndef YY_TYPEDEF_YY_SIZE_T
-+#define YY_TYPEDEF_YY_SIZE_T
-+typedef size_t yy_size_t;
-+#endif
-+
-+extern yy_size_t yyleng;
-
- extern FILE *yyin, *yyout;
-
-@@ -171,6 +176,7 @@ extern FILE *yyin, *yyout;
- #define EOB_ACT_LAST_MATCH 2
-
- #define YY_LESS_LINENO(n)
-+ #define YY_LINENO_REWIND_TO(ptr)
-
- /* Return all but the first "n" matched characters back to the input stream. */
- #define yyless(n) \
-@@ -188,11 +194,6 @@ extern FILE *yyin, *yyout;
-
- #define unput(c) yyunput( c, (yytext_ptr) )
-
--#ifndef YY_TYPEDEF_YY_SIZE_T
--#define YY_TYPEDEF_YY_SIZE_T
--typedef size_t yy_size_t;
--#endif
--
- #ifndef YY_STRUCT_YY_BUFFER_STATE
- #define YY_STRUCT_YY_BUFFER_STATE
- struct yy_buffer_state
-@@ -210,7 +211,7 @@ struct yy_buffer_state
- /* Number of characters read into yy_ch_buf, not including EOB
- * characters.
- */
-- int yy_n_chars;
-+ yy_size_t yy_n_chars;
-
- /* Whether we "own" the buffer - i.e., we know we created it,
- * and can realloc() it to grow it, and should free() it to
-@@ -280,8 +281,8 @@ static YY_BUFFER_STATE * yy_buffer_stack
-
- /* yy_hold_char holds the character lost when yytext is formed. */
- static char yy_hold_char;
--static int yy_n_chars; /* number of characters read into yy_ch_buf */
--int yyleng;
-+static yy_size_t yy_n_chars; /* number of characters read into yy_ch_buf */
-+yy_size_t yyleng;
-
- /* Points to current character in buffer. */
- static char *yy_c_buf_p = (char *) 0;
-@@ -309,7 +310,7 @@ static void yy_init_buffer (YY_BUFFER_ST
-
- YY_BUFFER_STATE yy_scan_buffer (char *base,yy_size_t size );
- YY_BUFFER_STATE yy_scan_string (yyconst char *yy_str );
--YY_BUFFER_STATE yy_scan_bytes (yyconst char *bytes,int len );
-+YY_BUFFER_STATE yy_scan_bytes (yyconst char *bytes,yy_size_t len );
-
- void *yyalloc (yy_size_t );
- void *yyrealloc (void *,yy_size_t );
-@@ -341,7 +342,7 @@ void yyfree (void * );
-
- /* Begin user sect3 */
-
--#define yywrap(n) 1
-+#define yywrap() 1
- #define YY_SKIP_YYWRAP
-
- typedef unsigned char YY_CHAR;
-@@ -372,8 +373,8 @@ static void yy_fatal_error (yyconst char
- *yy_cp = '\0'; \
- (yy_c_buf_p) = yy_cp;
-
--#define YY_NUM_RULES 31
--#define YY_END_OF_BUFFER 32
-+#define YY_NUM_RULES 30
-+#define YY_END_OF_BUFFER 31
- /* This struct is not used in this scanner,
- but its presence is necessary. */
- struct yy_trans_info
-@@ -381,26 +382,25 @@ struct yy_trans_info
- flex_int32_t yy_verify;
- flex_int32_t yy_nxt;
- };
--static yyconst flex_int16_t yy_accept[166] =
-+static yyconst flex_int16_t yy_accept[159] =
- { 0,
-- 0, 0, 0, 0, 0, 0, 0, 0, 32, 30,
-- 19, 19, 30, 30, 30, 30, 30, 30, 30, 30,
-- 30, 30, 30, 30, 30, 30, 16, 17, 17, 30,
-- 17, 11, 11, 19, 27, 0, 3, 0, 28, 13,
-- 0, 0, 12, 0, 0, 0, 0, 0, 0, 0,
-- 0, 22, 24, 26, 25, 23, 0, 10, 29, 0,
-- 0, 0, 15, 15, 17, 17, 17, 11, 11, 11,
-- 0, 13, 0, 12, 0, 0, 0, 21, 0, 0,
-- 0, 0, 0, 0, 0, 0, 0, 17, 11, 11,
-- 11, 0, 14, 20, 0, 0, 0, 0, 0, 0,
--
-- 0, 0, 0, 0, 17, 0, 0, 0, 0, 0,
-- 0, 0, 0, 0, 0, 17, 7, 0, 0, 0,
-- 0, 0, 0, 0, 2, 0, 0, 0, 0, 0,
-- 0, 0, 0, 0, 4, 18, 0, 0, 5, 2,
-- 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
-- 0, 0, 1, 0, 0, 0, 0, 6, 9, 0,
-- 0, 0, 0, 8, 0
-+ 0, 0, 0, 0, 0, 0, 0, 0, 31, 29,
-+ 18, 18, 29, 29, 29, 29, 29, 29, 29, 29,
-+ 29, 29, 29, 29, 29, 29, 15, 16, 16, 29,
-+ 16, 10, 10, 18, 26, 0, 3, 0, 27, 12,
-+ 0, 0, 11, 0, 0, 0, 0, 0, 0, 0,
-+ 21, 23, 25, 24, 22, 0, 9, 28, 0, 0,
-+ 0, 14, 14, 16, 16, 16, 10, 10, 10, 0,
-+ 12, 0, 11, 0, 0, 0, 20, 0, 0, 0,
-+ 0, 0, 0, 0, 0, 16, 10, 10, 10, 0,
-+ 13, 19, 0, 0, 0, 0, 0, 0, 0, 0,
-+
-+ 0, 16, 0, 0, 0, 0, 0, 0, 0, 0,
-+ 0, 16, 6, 0, 0, 0, 0, 0, 0, 2,
-+ 0, 0, 0, 0, 0, 0, 0, 0, 4, 17,
-+ 0, 0, 2, 0, 0, 0, 0, 0, 0, 0,
-+ 0, 0, 0, 0, 0, 1, 0, 0, 0, 0,
-+ 5, 8, 0, 0, 0, 0, 7, 0
- } ;
-
- static yyconst flex_int32_t yy_ec[256] =
-@@ -416,9 +416,9 @@ static yyconst flex_int32_t yy_ec[256] =
- 22, 22, 22, 22, 24, 22, 22, 25, 22, 22,
- 1, 26, 27, 1, 22, 1, 21, 28, 29, 30,
-
-- 31, 21, 32, 22, 33, 22, 22, 34, 35, 36,
-- 37, 38, 22, 39, 40, 41, 42, 43, 22, 25,
-- 44, 22, 45, 46, 47, 1, 1, 1, 1, 1,
-+ 31, 21, 22, 22, 32, 22, 22, 33, 34, 35,
-+ 36, 37, 22, 38, 39, 40, 41, 42, 22, 25,
-+ 43, 22, 44, 45, 46, 1, 1, 1, 1, 1,
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
-@@ -435,165 +435,163 @@ static yyconst flex_int32_t yy_ec[256] =
- 1, 1, 1, 1, 1
- } ;
-
--static yyconst flex_int32_t yy_meta[48] =
-+static yyconst flex_int32_t yy_meta[47] =
- { 0,
- 1, 1, 1, 1, 1, 1, 2, 3, 1, 2,
- 2, 2, 4, 5, 5, 5, 6, 1, 1, 1,
- 7, 8, 8, 8, 8, 1, 1, 7, 7, 7,
- 7, 8, 8, 8, 8, 8, 8, 8, 8, 8,
-- 8, 8, 8, 8, 3, 1, 4
-+ 8, 8, 8, 3, 1, 4
- } ;
-
--static yyconst flex_int16_t yy_base[180] =
-+static yyconst flex_int16_t yy_base[173] =
- { 0,
-- 0, 393, 35, 392, 66, 391, 38, 107, 397, 401,
-- 55, 113, 377, 112, 111, 111, 114, 42, 376, 106,
-- 377, 347, 126, 120, 0, 147, 401, 0, 124, 0,
-- 137, 158, 170, 163, 401, 153, 401, 389, 401, 0,
-- 378, 120, 401, 131, 380, 386, 355, 139, 351, 355,
-- 351, 401, 401, 401, 401, 401, 367, 401, 401, 185,
-- 350, 346, 401, 364, 0, 185, 347, 189, 356, 355,
-- 0, 0, 330, 180, 366, 141, 372, 361, 332, 338,
-- 331, 341, 334, 326, 205, 331, 337, 329, 401, 341,
-- 167, 316, 401, 349, 348, 320, 328, 346, 180, 318,
--
-- 324, 209, 324, 320, 322, 342, 338, 309, 306, 315,
-- 305, 315, 312, 192, 342, 341, 401, 293, 306, 282,
-- 268, 252, 255, 203, 285, 282, 272, 268, 252, 233,
-- 232, 239, 208, 107, 401, 401, 238, 211, 401, 211,
-- 212, 208, 228, 203, 215, 207, 233, 222, 212, 211,
-- 203, 227, 401, 237, 225, 204, 185, 401, 401, 149,
-- 128, 88, 42, 401, 401, 253, 259, 267, 271, 275,
-- 281, 288, 292, 300, 308, 312, 318, 326, 334
-+ 0, 383, 34, 382, 65, 381, 37, 105, 387, 391,
-+ 54, 111, 367, 110, 109, 109, 112, 41, 366, 104,
-+ 367, 338, 124, 117, 0, 144, 391, 0, 121, 0,
-+ 135, 155, 140, 179, 391, 160, 391, 379, 391, 0,
-+ 368, 141, 391, 167, 370, 376, 346, 103, 342, 345,
-+ 391, 391, 391, 391, 391, 358, 391, 391, 175, 342,
-+ 338, 391, 355, 0, 185, 339, 184, 347, 346, 0,
-+ 0, 322, 175, 357, 175, 363, 352, 324, 330, 323,
-+ 332, 326, 201, 324, 329, 322, 391, 333, 181, 309,
-+ 391, 341, 340, 313, 320, 338, 178, 311, 146, 317,
-+
-+ 314, 315, 335, 331, 303, 300, 309, 299, 308, 188,
-+ 336, 335, 391, 305, 320, 281, 283, 271, 203, 288,
-+ 281, 271, 266, 264, 245, 242, 208, 104, 391, 391,
-+ 244, 218, 204, 219, 206, 224, 201, 212, 204, 229,
-+ 215, 208, 207, 200, 219, 391, 233, 221, 200, 181,
-+ 391, 391, 149, 122, 86, 41, 391, 391, 245, 251,
-+ 259, 263, 267, 273, 280, 284, 292, 300, 304, 310,
-+ 318, 326
- } ;
-
--static yyconst flex_int16_t yy_def[180] =
-+static yyconst flex_int16_t yy_def[173] =
- { 0,
-- 165, 1, 1, 3, 165, 5, 1, 1, 165, 165,
-- 165, 165, 165, 166, 167, 168, 165, 165, 165, 165,
-- 169, 165, 165, 165, 170, 169, 165, 171, 172, 171,
-- 171, 165, 165, 165, 165, 166, 165, 166, 165, 173,
-- 165, 168, 165, 168, 174, 175, 165, 165, 165, 165,
-- 165, 165, 165, 165, 165, 165, 169, 165, 165, 165,
-- 165, 165, 165, 169, 171, 172, 171, 165, 165, 165,
-- 176, 173, 177, 168, 174, 174, 175, 165, 165, 165,
-- 165, 165, 165, 165, 165, 165, 165, 171, 165, 165,
-- 176, 177, 165, 165, 165, 165, 165, 165, 165, 165,
--
-- 165, 165, 165, 165, 171, 165, 165, 165, 165, 165,
-- 165, 165, 165, 178, 165, 171, 165, 165, 165, 165,
-- 165, 165, 165, 178, 165, 178, 165, 165, 165, 165,
-- 165, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-- 165, 165, 165, 165, 165, 165, 165, 179, 165, 165,
-- 165, 179, 165, 179, 165, 165, 165, 165, 165, 165,
-- 165, 165, 165, 165, 0, 165, 165, 165, 165, 165,
-- 165, 165, 165, 165, 165, 165, 165, 165, 165
-+ 158, 1, 1, 3, 158, 5, 1, 1, 158, 158,
-+ 158, 158, 158, 159, 160, 161, 158, 158, 158, 158,
-+ 162, 158, 158, 158, 163, 162, 158, 164, 165, 164,
-+ 164, 158, 158, 158, 158, 159, 158, 159, 158, 166,
-+ 158, 161, 158, 161, 167, 168, 158, 158, 158, 158,
-+ 158, 158, 158, 158, 158, 162, 158, 158, 158, 158,
-+ 158, 158, 162, 164, 165, 164, 158, 158, 158, 169,
-+ 166, 170, 161, 167, 167, 168, 158, 158, 158, 158,
-+ 158, 158, 158, 158, 158, 164, 158, 158, 169, 170,
-+ 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-+
-+ 158, 164, 158, 158, 158, 158, 158, 158, 158, 171,
-+ 158, 164, 158, 158, 158, 158, 158, 158, 171, 158,
-+ 171, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-+ 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-+ 172, 158, 158, 158, 172, 158, 172, 158, 158, 158,
-+ 158, 158, 158, 158, 158, 158, 158, 0, 158, 158,
-+ 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-+ 158, 158
- } ;
-
--static yyconst flex_int16_t yy_nxt[449] =
-+static yyconst flex_int16_t yy_nxt[438] =
- { 0,
- 10, 11, 12, 11, 13, 14, 10, 15, 16, 10,
- 10, 10, 17, 10, 10, 10, 10, 18, 19, 20,
- 21, 21, 21, 21, 21, 10, 10, 21, 21, 21,
- 21, 21, 21, 21, 21, 21, 21, 21, 21, 21,
-- 21, 21, 21, 21, 10, 22, 10, 24, 25, 25,
-- 25, 32, 33, 33, 164, 26, 34, 34, 34, 52,
-- 53, 27, 26, 26, 26, 26, 10, 11, 12, 11,
-- 13, 14, 28, 15, 16, 28, 28, 28, 24, 28,
-- 28, 28, 10, 18, 19, 20, 29, 29, 29, 29,
-- 29, 30, 10, 29, 29, 29, 29, 29, 29, 29,
--
-- 29, 29, 29, 29, 29, 29, 29, 29, 29, 29,
-- 10, 22, 10, 23, 34, 34, 34, 37, 39, 43,
-- 32, 33, 33, 45, 55, 56, 46, 60, 43, 45,
-- 65, 163, 46, 65, 65, 65, 44, 38, 60, 74,
-- 58, 47, 141, 48, 142, 44, 49, 47, 50, 48,
-- 76, 51, 62, 94, 50, 41, 44, 51, 37, 61,
-- 64, 64, 64, 58, 34, 34, 34, 64, 162, 80,
-- 67, 68, 68, 68, 64, 64, 64, 64, 38, 81,
-- 69, 70, 71, 68, 68, 68, 60, 161, 43, 69,
-- 70, 65, 69, 70, 65, 65, 65, 125, 85, 85,
--
-- 85, 58, 68, 68, 68, 44, 102, 110, 125, 133,
-- 102, 69, 70, 111, 114, 160, 159, 126, 85, 85,
-- 85, 140, 140, 140, 140, 140, 140, 153, 126, 147,
-- 147, 147, 153, 148, 147, 147, 147, 158, 148, 165,
-- 157, 156, 155, 151, 150, 149, 146, 154, 145, 144,
-- 143, 139, 154, 36, 36, 36, 36, 36, 36, 36,
-- 36, 40, 138, 137, 136, 40, 40, 42, 42, 42,
-- 42, 42, 42, 42, 42, 57, 57, 57, 57, 63,
-- 135, 63, 65, 134, 165, 65, 133, 65, 65, 66,
-- 132, 131, 66, 66, 66, 66, 72, 130, 72, 72,
--
-- 75, 75, 75, 75, 75, 75, 75, 75, 77, 77,
-- 77, 77, 77, 77, 77, 77, 91, 129, 91, 92,
-- 128, 92, 92, 127, 92, 92, 124, 124, 124, 124,
-- 124, 124, 124, 124, 152, 152, 152, 152, 152, 152,
-- 152, 152, 60, 60, 123, 122, 121, 120, 119, 118,
-- 117, 45, 116, 111, 115, 113, 112, 109, 108, 107,
-- 46, 106, 93, 89, 105, 104, 103, 101, 100, 99,
-- 98, 97, 96, 95, 78, 76, 93, 90, 89, 88,
-- 58, 87, 86, 58, 84, 83, 82, 79, 78, 76,
-- 73, 165, 59, 58, 54, 35, 165, 31, 23, 23,
--
-- 9, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-- 165, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-- 165, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-- 165, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-- 165, 165, 165, 165, 165, 165, 165, 165
-+ 21, 21, 21, 10, 22, 10, 24, 25, 25, 25,
-+ 32, 33, 33, 157, 26, 34, 34, 34, 51, 52,
-+ 27, 26, 26, 26, 26, 10, 11, 12, 11, 13,
-+ 14, 28, 15, 16, 28, 28, 28, 24, 28, 28,
-+ 28, 10, 18, 19, 20, 29, 29, 29, 29, 29,
-+ 30, 10, 29, 29, 29, 29, 29, 29, 29, 29,
-+
-+ 29, 29, 29, 29, 29, 29, 29, 29, 10, 22,
-+ 10, 23, 34, 34, 34, 37, 39, 43, 32, 33,
-+ 33, 45, 54, 55, 46, 59, 45, 64, 156, 46,
-+ 64, 64, 64, 79, 44, 38, 59, 57, 134, 47,
-+ 135, 48, 80, 49, 47, 50, 48, 99, 61, 43,
-+ 50, 110, 41, 67, 67, 67, 60, 63, 63, 63,
-+ 57, 155, 68, 69, 63, 37, 44, 66, 67, 67,
-+ 67, 63, 63, 63, 63, 73, 59, 68, 69, 70,
-+ 34, 34, 34, 43, 75, 38, 154, 92, 83, 83,
-+ 83, 64, 44, 120, 64, 64, 64, 67, 67, 67,
-+
-+ 44, 57, 99, 68, 69, 107, 68, 69, 120, 127,
-+ 108, 153, 152, 121, 83, 83, 83, 133, 133, 133,
-+ 146, 133, 133, 133, 146, 140, 140, 140, 121, 141,
-+ 140, 140, 140, 151, 141, 158, 150, 149, 148, 144,
-+ 147, 143, 142, 139, 147, 36, 36, 36, 36, 36,
-+ 36, 36, 36, 40, 138, 137, 136, 40, 40, 42,
-+ 42, 42, 42, 42, 42, 42, 42, 56, 56, 56,
-+ 56, 62, 132, 62, 64, 131, 130, 64, 129, 64,
-+ 64, 65, 128, 158, 65, 65, 65, 65, 71, 127,
-+ 71, 71, 74, 74, 74, 74, 74, 74, 74, 74,
-+
-+ 76, 76, 76, 76, 76, 76, 76, 76, 89, 126,
-+ 89, 90, 125, 90, 90, 124, 90, 90, 119, 119,
-+ 119, 119, 119, 119, 119, 119, 145, 145, 145, 145,
-+ 145, 145, 145, 145, 123, 122, 59, 59, 118, 117,
-+ 116, 115, 114, 113, 45, 112, 108, 111, 109, 106,
-+ 105, 104, 46, 103, 91, 87, 102, 101, 100, 98,
-+ 97, 96, 95, 94, 93, 77, 75, 91, 88, 87,
-+ 86, 57, 85, 84, 57, 82, 81, 78, 77, 75,
-+ 72, 158, 58, 57, 53, 35, 158, 31, 23, 23,
-+ 9, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-+
-+ 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-+ 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-+ 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-+ 158, 158, 158, 158, 158, 158, 158
- } ;
-
--static yyconst flex_int16_t yy_chk[449] =
-+static yyconst flex_int16_t yy_chk[438] =
- { 0,
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
-- 1, 1, 1, 1, 1, 1, 1, 3, 3, 3,
-- 3, 7, 7, 7, 163, 3, 11, 11, 11, 18,
-- 18, 3, 3, 3, 3, 3, 5, 5, 5, 5,
-+ 1, 1, 1, 1, 1, 1, 3, 3, 3, 3,
-+ 7, 7, 7, 156, 3, 11, 11, 11, 18, 18,
-+ 3, 3, 3, 3, 3, 5, 5, 5, 5, 5,
- 5, 5, 5, 5, 5, 5, 5, 5, 5, 5,
- 5, 5, 5, 5, 5, 5, 5, 5, 5, 5,
- 5, 5, 5, 5, 5, 5, 5, 5, 5, 5,
-
- 5, 5, 5, 5, 5, 5, 5, 5, 5, 5,
-- 5, 5, 5, 8, 12, 12, 12, 14, 15, 16,
-- 8, 8, 8, 17, 20, 20, 17, 23, 42, 24,
-- 29, 162, 24, 29, 29, 29, 16, 14, 31, 44,
-- 29, 17, 134, 17, 134, 42, 17, 24, 17, 24,
-- 76, 17, 24, 76, 24, 15, 44, 24, 36, 23,
-- 26, 26, 26, 26, 34, 34, 34, 26, 161, 48,
-- 31, 32, 32, 32, 26, 26, 26, 26, 36, 48,
-- 32, 32, 32, 33, 33, 33, 60, 160, 74, 91,
-- 91, 66, 33, 33, 66, 66, 66, 114, 60, 60,
--
-- 60, 66, 68, 68, 68, 74, 85, 99, 124, 133,
-- 102, 68, 68, 99, 102, 157, 156, 114, 85, 85,
-- 85, 133, 133, 133, 140, 140, 140, 148, 124, 143,
-- 143, 143, 152, 143, 147, 147, 147, 155, 147, 154,
-- 151, 150, 149, 146, 145, 144, 142, 148, 141, 138,
-- 137, 132, 152, 166, 166, 166, 166, 166, 166, 166,
-- 166, 167, 131, 130, 129, 167, 167, 168, 168, 168,
-- 168, 168, 168, 168, 168, 169, 169, 169, 169, 170,
-- 128, 170, 171, 127, 126, 171, 125, 171, 171, 172,
-- 123, 122, 172, 172, 172, 172, 173, 121, 173, 173,
--
-- 174, 174, 174, 174, 174, 174, 174, 174, 175, 175,
-- 175, 175, 175, 175, 175, 175, 176, 120, 176, 177,
-- 119, 177, 177, 118, 177, 177, 178, 178, 178, 178,
-- 178, 178, 178, 178, 179, 179, 179, 179, 179, 179,
-- 179, 179, 116, 115, 113, 112, 111, 110, 109, 108,
-- 107, 106, 105, 104, 103, 101, 100, 98, 97, 96,
-- 95, 94, 92, 90, 88, 87, 86, 84, 83, 82,
-- 81, 80, 79, 78, 77, 75, 73, 70, 69, 67,
-- 64, 62, 61, 57, 51, 50, 49, 47, 46, 45,
-+ 5, 8, 12, 12, 12, 14, 15, 16, 8, 8,
-+ 8, 17, 20, 20, 17, 23, 24, 29, 155, 24,
-+ 29, 29, 29, 48, 16, 14, 31, 29, 128, 17,
-+ 128, 17, 48, 17, 24, 17, 24, 99, 24, 42,
-+ 24, 99, 15, 33, 33, 33, 23, 26, 26, 26,
-+ 26, 154, 33, 33, 26, 36, 42, 31, 32, 32,
-+ 32, 26, 26, 26, 26, 44, 59, 32, 32, 32,
-+ 34, 34, 34, 73, 75, 36, 153, 75, 59, 59,
-+ 59, 65, 44, 110, 65, 65, 65, 67, 67, 67,
-+
-+ 73, 65, 83, 89, 89, 97, 67, 67, 119, 127,
-+ 97, 150, 149, 110, 83, 83, 83, 133, 133, 133,
-+ 141, 127, 127, 127, 145, 136, 136, 136, 119, 136,
-+ 140, 140, 140, 148, 140, 147, 144, 143, 142, 139,
-+ 141, 138, 137, 135, 145, 159, 159, 159, 159, 159,
-+ 159, 159, 159, 160, 134, 132, 131, 160, 160, 161,
-+ 161, 161, 161, 161, 161, 161, 161, 162, 162, 162,
-+ 162, 163, 126, 163, 164, 125, 124, 164, 123, 164,
-+ 164, 165, 122, 121, 165, 165, 165, 165, 166, 120,
-+ 166, 166, 167, 167, 167, 167, 167, 167, 167, 167,
-+
-+ 168, 168, 168, 168, 168, 168, 168, 168, 169, 118,
-+ 169, 170, 117, 170, 170, 116, 170, 170, 171, 171,
-+ 171, 171, 171, 171, 171, 171, 172, 172, 172, 172,
-+ 172, 172, 172, 172, 115, 114, 112, 111, 109, 108,
-+ 107, 106, 105, 104, 103, 102, 101, 100, 98, 96,
-+ 95, 94, 93, 92, 90, 88, 86, 85, 84, 82,
-+ 81, 80, 79, 78, 77, 76, 74, 72, 69, 68,
-+ 66, 63, 61, 60, 56, 50, 49, 47, 46, 45,
- 41, 38, 22, 21, 19, 13, 9, 6, 4, 2,
-+ 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-
-- 165, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-- 165, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-- 165, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-- 165, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-- 165, 165, 165, 165, 165, 165, 165, 165
-+ 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-+ 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-+ 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-+ 158, 158, 158, 158, 158, 158, 158
- } ;
-
- static yy_state_type yy_last_accepting_state;
-@@ -664,7 +662,7 @@ static int dts_version = 1;
- static void push_input_file(const char *filename);
- static bool pop_input_file(void);
- static void lexical_error(const char *fmt, ...);
--#line 668 "dtc-lexer.lex.c"
-+#line 666 "dtc-lexer.lex.c"
-
- #define INITIAL 0
- #define BYTESTRING 1
-@@ -706,7 +704,7 @@ FILE *yyget_out (void );
-
- void yyset_out (FILE * out_str );
-
--int yyget_leng (void );
-+yy_size_t yyget_leng (void );
-
- char *yyget_text (void );
-
-@@ -855,10 +853,6 @@ YY_DECL
- register char *yy_cp, *yy_bp;
- register int yy_act;
-
--#line 68 "dtc-lexer.l"
--
--#line 861 "dtc-lexer.lex.c"
--
- if ( !(yy_init) )
- {
- (yy_init) = 1;
-@@ -885,6 +879,11 @@ YY_DECL
- yy_load_buffer_state( );
- }
-
-+ {
-+#line 68 "dtc-lexer.l"
-+
-+#line 886 "dtc-lexer.lex.c"
-+
- while ( 1 ) /* loops until end-of-file is reached */
- {
- yy_cp = (yy_c_buf_p);
-@@ -902,7 +901,7 @@ YY_DECL
- yy_match:
- do
- {
-- register YY_CHAR yy_c = yy_ec[YY_SC_TO_UI(*yy_cp)];
-+ register YY_CHAR yy_c = yy_ec[YY_SC_TO_UI(*yy_cp)] ;
- if ( yy_accept[yy_current_state] )
- {
- (yy_last_accepting_state) = yy_current_state;
-@@ -911,13 +910,13 @@ yy_match:
- while ( yy_chk[yy_base[yy_current_state] + yy_c] != yy_current_state )
- {
- yy_current_state = (int) yy_def[yy_current_state];
-- if ( yy_current_state >= 166 )
-+ if ( yy_current_state >= 159 )
- yy_c = yy_meta[(unsigned int) yy_c];
- }
- yy_current_state = yy_nxt[yy_base[yy_current_state] + (unsigned int) yy_c];
- ++yy_cp;
- }
-- while ( yy_current_state != 165 );
-+ while ( yy_current_state != 158 );
- yy_cp = (yy_last_accepting_cpos);
- yy_current_state = (yy_last_accepting_state);
-
-@@ -1008,31 +1007,23 @@ case 5:
- YY_RULE_SETUP
- #line 116 "dtc-lexer.l"
- {
-- DPRINT("Keyword: /plugin/\n");
-- return DT_PLUGIN;
-- }
-- YY_BREAK
--case 6:
--YY_RULE_SETUP
--#line 121 "dtc-lexer.l"
--{
- DPRINT("Keyword: /memreserve/\n");
- BEGIN_DEFAULT();
- return DT_MEMRESERVE;
- }
- YY_BREAK
--case 7:
-+case 6:
- YY_RULE_SETUP
--#line 127 "dtc-lexer.l"
-+#line 122 "dtc-lexer.l"
- {
- DPRINT("Keyword: /bits/\n");
- BEGIN_DEFAULT();
- return DT_BITS;
- }
- YY_BREAK
--case 8:
-+case 7:
- YY_RULE_SETUP
--#line 133 "dtc-lexer.l"
-+#line 128 "dtc-lexer.l"
- {
- DPRINT("Keyword: /delete-property/\n");
- DPRINT("<PROPNODENAME>\n");
-@@ -1040,9 +1031,9 @@ YY_RULE_SETUP
- return DT_DEL_PROP;
- }
- YY_BREAK
--case 9:
-+case 8:
- YY_RULE_SETUP
--#line 140 "dtc-lexer.l"
-+#line 135 "dtc-lexer.l"
- {
- DPRINT("Keyword: /delete-node/\n");
- DPRINT("<PROPNODENAME>\n");
-@@ -1050,9 +1041,9 @@ YY_RULE_SETUP
- return DT_DEL_NODE;
- }
- YY_BREAK
--case 10:
-+case 9:
- YY_RULE_SETUP
--#line 147 "dtc-lexer.l"
-+#line 142 "dtc-lexer.l"
- {
- DPRINT("Label: %s\n", yytext);
- yylval.labelref = xstrdup(yytext);
-@@ -1060,9 +1051,9 @@ YY_RULE_SETUP
- return DT_LABEL;
- }
- YY_BREAK
--case 11:
-+case 10:
- YY_RULE_SETUP
--#line 154 "dtc-lexer.l"
-+#line 149 "dtc-lexer.l"
- {
- char *e;
- DPRINT("Integer Literal: '%s'\n", yytext);
-@@ -1082,10 +1073,10 @@ YY_RULE_SETUP
- return DT_LITERAL;
- }
- YY_BREAK
--case 12:
--/* rule 12 can match eol */
-+case 11:
-+/* rule 11 can match eol */
- YY_RULE_SETUP
--#line 173 "dtc-lexer.l"
-+#line 168 "dtc-lexer.l"
- {
- struct data d;
- DPRINT("Character literal: %s\n", yytext);
-@@ -1107,18 +1098,18 @@ YY_RULE_SETUP
- return DT_CHAR_LITERAL;
- }
- YY_BREAK
--case 13:
-+case 12:
- YY_RULE_SETUP
--#line 194 "dtc-lexer.l"
-+#line 189 "dtc-lexer.l"
- { /* label reference */
- DPRINT("Ref: %s\n", yytext+1);
- yylval.labelref = xstrdup(yytext+1);
- return DT_REF;
- }
- YY_BREAK
--case 14:
-+case 13:
- YY_RULE_SETUP
--#line 200 "dtc-lexer.l"
-+#line 195 "dtc-lexer.l"
- { /* new-style path reference */
- yytext[yyleng-1] = '\0';
- DPRINT("Ref: %s\n", yytext+2);
-@@ -1126,27 +1117,27 @@ YY_RULE_SETUP
- return DT_REF;
- }
- YY_BREAK
--case 15:
-+case 14:
- YY_RULE_SETUP
--#line 207 "dtc-lexer.l"
-+#line 202 "dtc-lexer.l"
- {
- yylval.byte = strtol(yytext, NULL, 16);
- DPRINT("Byte: %02x\n", (int)yylval.byte);
- return DT_BYTE;
- }
- YY_BREAK
--case 16:
-+case 15:
- YY_RULE_SETUP
--#line 213 "dtc-lexer.l"
-+#line 208 "dtc-lexer.l"
- {
- DPRINT("/BYTESTRING\n");
- BEGIN_DEFAULT();
- return ']';
- }
- YY_BREAK
--case 17:
-+case 16:
- YY_RULE_SETUP
--#line 219 "dtc-lexer.l"
-+#line 214 "dtc-lexer.l"
- {
- DPRINT("PropNodeName: %s\n", yytext);
- yylval.propnodename = xstrdup((yytext[0] == '\\') ?
-@@ -1155,75 +1146,75 @@ YY_RULE_SETUP
- return DT_PROPNODENAME;
- }
- YY_BREAK
--case 18:
-+case 17:
- YY_RULE_SETUP
--#line 227 "dtc-lexer.l"
-+#line 222 "dtc-lexer.l"
- {
- DPRINT("Binary Include\n");
- return DT_INCBIN;
- }
- YY_BREAK
--case 19:
--/* rule 19 can match eol */
-+case 18:
-+/* rule 18 can match eol */
- YY_RULE_SETUP
--#line 232 "dtc-lexer.l"
-+#line 227 "dtc-lexer.l"
- /* eat whitespace */
- YY_BREAK
--case 20:
--/* rule 20 can match eol */
-+case 19:
-+/* rule 19 can match eol */
- YY_RULE_SETUP
--#line 233 "dtc-lexer.l"
-+#line 228 "dtc-lexer.l"
- /* eat C-style comments */
- YY_BREAK
--case 21:
--/* rule 21 can match eol */
-+case 20:
-+/* rule 20 can match eol */
- YY_RULE_SETUP
--#line 234 "dtc-lexer.l"
-+#line 229 "dtc-lexer.l"
- /* eat C++-style comments */
- YY_BREAK
--case 22:
-+case 21:
- YY_RULE_SETUP
--#line 236 "dtc-lexer.l"
-+#line 231 "dtc-lexer.l"
- { return DT_LSHIFT; };
- YY_BREAK
--case 23:
-+case 22:
- YY_RULE_SETUP
--#line 237 "dtc-lexer.l"
-+#line 232 "dtc-lexer.l"
- { return DT_RSHIFT; };
- YY_BREAK
--case 24:
-+case 23:
- YY_RULE_SETUP
--#line 238 "dtc-lexer.l"
-+#line 233 "dtc-lexer.l"
- { return DT_LE; };
- YY_BREAK
--case 25:
-+case 24:
- YY_RULE_SETUP
--#line 239 "dtc-lexer.l"
-+#line 234 "dtc-lexer.l"
- { return DT_GE; };
- YY_BREAK
--case 26:
-+case 25:
- YY_RULE_SETUP
--#line 240 "dtc-lexer.l"
-+#line 235 "dtc-lexer.l"
- { return DT_EQ; };
- YY_BREAK
--case 27:
-+case 26:
- YY_RULE_SETUP
--#line 241 "dtc-lexer.l"
-+#line 236 "dtc-lexer.l"
- { return DT_NE; };
- YY_BREAK
--case 28:
-+case 27:
- YY_RULE_SETUP
--#line 242 "dtc-lexer.l"
-+#line 237 "dtc-lexer.l"
- { return DT_AND; };
- YY_BREAK
--case 29:
-+case 28:
- YY_RULE_SETUP
--#line 243 "dtc-lexer.l"
-+#line 238 "dtc-lexer.l"
- { return DT_OR; };
- YY_BREAK
--case 30:
-+case 29:
- YY_RULE_SETUP
--#line 245 "dtc-lexer.l"
-+#line 240 "dtc-lexer.l"
- {
- DPRINT("Char: %c (\\x%02x)\n", yytext[0],
- (unsigned)yytext[0]);
-@@ -1239,12 +1230,12 @@ YY_RULE_SETUP
- return yytext[0];
- }
- YY_BREAK
--case 31:
-+case 30:
- YY_RULE_SETUP
--#line 260 "dtc-lexer.l"
-+#line 255 "dtc-lexer.l"
- ECHO;
- YY_BREAK
--#line 1248 "dtc-lexer.lex.c"
-+#line 1239 "dtc-lexer.lex.c"
-
- case YY_END_OF_BUFFER:
- {
-@@ -1374,6 +1365,7 @@ ECHO;
- "fatal flex scanner internal error--no action found" );
- } /* end of action switch */
- } /* end of scanning one token */
-+ } /* end of user's declarations */
- } /* end of yylex */
-
- /* yy_get_next_buffer - try to read in a new buffer
-@@ -1429,21 +1421,21 @@ static int yy_get_next_buffer (void)
-
- else
- {
-- int num_to_read =
-+ yy_size_t num_to_read =
- YY_CURRENT_BUFFER_LVALUE->yy_buf_size - number_to_move - 1;
-
- while ( num_to_read <= 0 )
- { /* Not enough room in the buffer - grow it. */
-
- /* just a shorter name for the current buffer */
-- YY_BUFFER_STATE b = YY_CURRENT_BUFFER;
-+ YY_BUFFER_STATE b = YY_CURRENT_BUFFER_LVALUE;
-
- int yy_c_buf_p_offset =
- (int) ((yy_c_buf_p) - b->yy_ch_buf);
-
- if ( b->yy_is_our_buffer )
- {
-- int new_size = b->yy_buf_size * 2;
-+ yy_size_t new_size = b->yy_buf_size * 2;
-
- if ( new_size <= 0 )
- b->yy_buf_size += b->yy_buf_size / 8;
-@@ -1474,7 +1466,7 @@ static int yy_get_next_buffer (void)
-
- /* Read in more data. */
- YY_INPUT( (&YY_CURRENT_BUFFER_LVALUE->yy_ch_buf[number_to_move]),
-- (yy_n_chars), (size_t) num_to_read );
-+ (yy_n_chars), num_to_read );
-
- YY_CURRENT_BUFFER_LVALUE->yy_n_chars = (yy_n_chars);
- }
-@@ -1536,7 +1528,7 @@ static int yy_get_next_buffer (void)
- while ( yy_chk[yy_base[yy_current_state] + yy_c] != yy_current_state )
- {
- yy_current_state = (int) yy_def[yy_current_state];
-- if ( yy_current_state >= 166 )
-+ if ( yy_current_state >= 159 )
- yy_c = yy_meta[(unsigned int) yy_c];
- }
- yy_current_state = yy_nxt[yy_base[yy_current_state] + (unsigned int) yy_c];
-@@ -1564,13 +1556,13 @@ static int yy_get_next_buffer (void)
- while ( yy_chk[yy_base[yy_current_state] + yy_c] != yy_current_state )
- {
- yy_current_state = (int) yy_def[yy_current_state];
-- if ( yy_current_state >= 166 )
-+ if ( yy_current_state >= 159 )
- yy_c = yy_meta[(unsigned int) yy_c];
- }
- yy_current_state = yy_nxt[yy_base[yy_current_state] + (unsigned int) yy_c];
-- yy_is_jam = (yy_current_state == 165);
-+ yy_is_jam = (yy_current_state == 158);
-
-- return yy_is_jam ? 0 : yy_current_state;
-+ return yy_is_jam ? 0 : yy_current_state;
- }
-
- #ifndef YY_NO_INPUT
-@@ -1597,7 +1589,7 @@ static int yy_get_next_buffer (void)
-
- else
- { /* need more input */
-- int offset = (yy_c_buf_p) - (yytext_ptr);
-+ yy_size_t offset = (yy_c_buf_p) - (yytext_ptr);
- ++(yy_c_buf_p);
-
- switch ( yy_get_next_buffer( ) )
-@@ -1871,7 +1863,7 @@ void yypop_buffer_state (void)
- */
- static void yyensure_buffer_stack (void)
- {
-- int num_to_alloc;
-+ yy_size_t num_to_alloc;
-
- if (!(yy_buffer_stack)) {
-
-@@ -1968,12 +1960,12 @@ YY_BUFFER_STATE yy_scan_string (yyconst
- *
- * @return the newly allocated buffer state object.
- */
--YY_BUFFER_STATE yy_scan_bytes (yyconst char * yybytes, int _yybytes_len )
-+YY_BUFFER_STATE yy_scan_bytes (yyconst char * yybytes, yy_size_t _yybytes_len )
- {
- YY_BUFFER_STATE b;
- char *buf;
- yy_size_t n;
-- int i;
-+ yy_size_t i;
-
- /* Get memory for full buffer, including space for trailing EOB's. */
- n = _yybytes_len + 2;
-@@ -2055,7 +2047,7 @@ FILE *yyget_out (void)
- /** Get the length of the current token.
- *
- */
--int yyget_leng (void)
-+yy_size_t yyget_leng (void)
- {
- return yyleng;
- }
-@@ -2203,7 +2195,7 @@ void yyfree (void * ptr )
-
- #define YYTABLES_NAME "yytables"
-
--#line 260 "dtc-lexer.l"
-+#line 254 "dtc-lexer.l"
-
-
-
---- a/scripts/dtc/dtc-parser.tab.c_shipped
-+++ b/scripts/dtc/dtc-parser.tab.c_shipped
-@@ -1,19 +1,19 @@
--/* A Bison parser, made by GNU Bison 2.5. */
-+/* A Bison parser, made by GNU Bison 3.0.2. */
-
- /* Bison implementation for Yacc-like parsers in C
--
-- Copyright (C) 1984, 1989-1990, 2000-2011 Free Software Foundation, Inc.
--
-+
-+ Copyright (C) 1984, 1989-1990, 2000-2013 Free Software Foundation, Inc.
-+
- This program is free software: you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation, either version 3 of the License, or
- (at your option) any later version.
--
-+
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
--
-+
- You should have received a copy of the GNU General Public License
- along with this program. If not, see <http://www.gnu.org/licenses/>. */
-
-@@ -26,7 +26,7 @@
- special exception, which will cause the skeleton and the resulting
- Bison output files to be licensed under the GNU General Public
- License without this special exception.
--
-+
- This special exception was added by the Free Software Foundation in
- version 2.2 of Bison. */
-
-@@ -44,7 +44,7 @@
- #define YYBISON 1
-
- /* Bison version. */
--#define YYBISON_VERSION "2.5"
-+#define YYBISON_VERSION "3.0.2"
-
- /* Skeleton name. */
- #define YYSKELETON_NAME "yacc.c"
-@@ -58,18 +58,13 @@
- /* Pull parsers. */
- #define YYPULL 1
-
--/* Using locations. */
--#define YYLSP_NEEDED 1
-
-
-
- /* Copy the first part of user declarations. */
--
--/* Line 268 of yacc.c */
--#line 20 "dtc-parser.y"
-+#line 20 "dtc-parser.y" /* yacc.c:339 */
-
- #include <stdio.h>
--#include <inttypes.h>
-
- #include "dtc.h"
- #include "srcpos.h"
-@@ -85,14 +80,15 @@ extern void yyerror(char const *s);
- extern struct boot_info *the_boot_info;
- extern bool treesource_error;
-
-+#line 84 "dtc-parser.tab.c" /* yacc.c:339 */
-
--/* Line 268 of yacc.c */
--#line 91 "dtc-parser.tab.c"
--
--/* Enabling traces. */
--#ifndef YYDEBUG
--# define YYDEBUG 0
--#endif
-+# ifndef YY_NULLPTR
-+# if defined __cplusplus && 201103L <= __cplusplus
-+# define YY_NULLPTR nullptr
-+# else
-+# define YY_NULLPTR 0
-+# endif
-+# endif
-
- /* Enabling verbose error messages. */
- #ifdef YYERROR_VERBOSE
-@@ -102,51 +98,53 @@ extern bool treesource_error;
- # define YYERROR_VERBOSE 0
- #endif
-
--/* Enabling the token table. */
--#ifndef YYTOKEN_TABLE
--# define YYTOKEN_TABLE 0
-+/* In a future release of Bison, this section will be replaced
-+ by #include "dtc-parser.tab.h". */
-+#ifndef YY_YY_DTC_PARSER_TAB_H_INCLUDED
-+# define YY_YY_DTC_PARSER_TAB_H_INCLUDED
-+/* Debug traces. */
-+#ifndef YYDEBUG
-+# define YYDEBUG 0
-+#endif
-+#if YYDEBUG
-+extern int yydebug;
- #endif
-
--
--/* Tokens. */
-+/* Token type. */
- #ifndef YYTOKENTYPE
- # define YYTOKENTYPE
-- /* Put the tokens into the symbol table, so that GDB and other debuggers
-- know about them. */
-- enum yytokentype {
-- DT_V1 = 258,
-- DT_PLUGIN = 259,
-- DT_MEMRESERVE = 260,
-- DT_LSHIFT = 261,
-- DT_RSHIFT = 262,
-- DT_LE = 263,
-- DT_GE = 264,
-- DT_EQ = 265,
-- DT_NE = 266,
-- DT_AND = 267,
-- DT_OR = 268,
-- DT_BITS = 269,
-- DT_DEL_PROP = 270,
-- DT_DEL_NODE = 271,
-- DT_PROPNODENAME = 272,
-- DT_LITERAL = 273,
-- DT_CHAR_LITERAL = 274,
-- DT_BYTE = 275,
-- DT_STRING = 276,
-- DT_LABEL = 277,
-- DT_REF = 278,
-- DT_INCBIN = 279
-- };
-+ enum yytokentype
-+ {
-+ DT_V1 = 258,
-+ DT_MEMRESERVE = 259,
-+ DT_LSHIFT = 260,
-+ DT_RSHIFT = 261,
-+ DT_LE = 262,
-+ DT_GE = 263,
-+ DT_EQ = 264,
-+ DT_NE = 265,
-+ DT_AND = 266,
-+ DT_OR = 267,
-+ DT_BITS = 268,
-+ DT_DEL_PROP = 269,
-+ DT_DEL_NODE = 270,
-+ DT_PROPNODENAME = 271,
-+ DT_LITERAL = 272,
-+ DT_CHAR_LITERAL = 273,
-+ DT_BYTE = 274,
-+ DT_STRING = 275,
-+ DT_LABEL = 276,
-+ DT_REF = 277,
-+ DT_INCBIN = 278
-+ };
- #endif
-
--
--
-+/* Value type. */
- #if ! defined YYSTYPE && ! defined YYSTYPE_IS_DECLARED
--typedef union YYSTYPE
-+typedef union YYSTYPE YYSTYPE;
-+union YYSTYPE
- {
--
--/* Line 293 of yacc.c */
--#line 39 "dtc-parser.y"
-+#line 38 "dtc-parser.y" /* yacc.c:355 */
-
- char *propnodename;
- char *labelref;
-@@ -164,37 +162,37 @@ typedef union YYSTYPE
- struct node *nodelist;
- struct reserve_info *re;
- uint64_t integer;
-- int is_plugin;
--
--
-
--/* Line 293 of yacc.c */
--#line 173 "dtc-parser.tab.c"
--} YYSTYPE;
-+#line 167 "dtc-parser.tab.c" /* yacc.c:355 */
-+};
- # define YYSTYPE_IS_TRIVIAL 1
--# define yystype YYSTYPE /* obsolescent; will be withdrawn */
- # define YYSTYPE_IS_DECLARED 1
- #endif
-
-+/* Location type. */
- #if ! defined YYLTYPE && ! defined YYLTYPE_IS_DECLARED
--typedef struct YYLTYPE
-+typedef struct YYLTYPE YYLTYPE;
-+struct YYLTYPE
- {
- int first_line;
- int first_column;
- int last_line;
- int last_column;
--} YYLTYPE;
--# define yyltype YYLTYPE /* obsolescent; will be withdrawn */
-+};
- # define YYLTYPE_IS_DECLARED 1
- # define YYLTYPE_IS_TRIVIAL 1
- #endif
-
-
--/* Copy the second part of user declarations. */
-+extern YYSTYPE yylval;
-+extern YYLTYPE yylloc;
-+int yyparse (void);
-+
-+#endif /* !YY_YY_DTC_PARSER_TAB_H_INCLUDED */
-
-+/* Copy the second part of user declarations. */
-
--/* Line 343 of yacc.c */
--#line 198 "dtc-parser.tab.c"
-+#line 196 "dtc-parser.tab.c" /* yacc.c:358 */
-
- #ifdef short
- # undef short
-@@ -208,11 +206,8 @@ typedef unsigned char yytype_uint8;
-
- #ifdef YYTYPE_INT8
- typedef YYTYPE_INT8 yytype_int8;
--#elif (defined __STDC__ || defined __C99__FUNC__ \
-- || defined __cplusplus || defined _MSC_VER)
--typedef signed char yytype_int8;
- #else
--typedef short int yytype_int8;
-+typedef signed char yytype_int8;
- #endif
-
- #ifdef YYTYPE_UINT16
-@@ -232,8 +227,7 @@ typedef short int yytype_int16;
- # define YYSIZE_T __SIZE_TYPE__
- # elif defined size_t
- # define YYSIZE_T size_t
--# elif ! defined YYSIZE_T && (defined __STDC__ || defined __C99__FUNC__ \
-- || defined __cplusplus || defined _MSC_VER)
-+# elif ! defined YYSIZE_T
- # include <stddef.h> /* INFRINGES ON USER NAME SPACE */
- # define YYSIZE_T size_t
- # else
-@@ -247,39 +241,68 @@ typedef short int yytype_int16;
- # if defined YYENABLE_NLS && YYENABLE_NLS
- # if ENABLE_NLS
- # include <libintl.h> /* INFRINGES ON USER NAME SPACE */
--# define YY_(msgid) dgettext ("bison-runtime", msgid)
-+# define YY_(Msgid) dgettext ("bison-runtime", Msgid)
- # endif
- # endif
- # ifndef YY_
--# define YY_(msgid) msgid
-+# define YY_(Msgid) Msgid
-+# endif
-+#endif
-+
-+#ifndef YY_ATTRIBUTE
-+# if (defined __GNUC__ \
-+ && (2 < __GNUC__ || (__GNUC__ == 2 && 96 <= __GNUC_MINOR__))) \
-+ || defined __SUNPRO_C && 0x5110 <= __SUNPRO_C
-+# define YY_ATTRIBUTE(Spec) __attribute__(Spec)
-+# else
-+# define YY_ATTRIBUTE(Spec) /* empty */
-+# endif
-+#endif
-+
-+#ifndef YY_ATTRIBUTE_PURE
-+# define YY_ATTRIBUTE_PURE YY_ATTRIBUTE ((__pure__))
-+#endif
-+
-+#ifndef YY_ATTRIBUTE_UNUSED
-+# define YY_ATTRIBUTE_UNUSED YY_ATTRIBUTE ((__unused__))
-+#endif
-+
-+#if !defined _Noreturn \
-+ && (!defined __STDC_VERSION__ || __STDC_VERSION__ < 201112)
-+# if defined _MSC_VER && 1200 <= _MSC_VER
-+# define _Noreturn __declspec (noreturn)
-+# else
-+# define _Noreturn YY_ATTRIBUTE ((__noreturn__))
- # endif
- #endif
-
- /* Suppress unused-variable warnings by "using" E. */
- #if ! defined lint || defined __GNUC__
--# define YYUSE(e) ((void) (e))
-+# define YYUSE(E) ((void) (E))
- #else
--# define YYUSE(e) /* empty */
-+# define YYUSE(E) /* empty */
- #endif
-
--/* Identity function, used to suppress warnings about constant conditions. */
--#ifndef lint
--# define YYID(n) (n)
--#else
--#if (defined __STDC__ || defined __C99__FUNC__ \
-- || defined __cplusplus || defined _MSC_VER)
--static int
--YYID (int yyi)
-+#if defined __GNUC__ && 407 <= __GNUC__ * 100 + __GNUC_MINOR__
-+/* Suppress an incorrect diagnostic about yylval being uninitialized. */
-+# define YY_IGNORE_MAYBE_UNINITIALIZED_BEGIN \
-+ _Pragma ("GCC diagnostic push") \
-+ _Pragma ("GCC diagnostic ignored \"-Wuninitialized\"")\
-+ _Pragma ("GCC diagnostic ignored \"-Wmaybe-uninitialized\"")
-+# define YY_IGNORE_MAYBE_UNINITIALIZED_END \
-+ _Pragma ("GCC diagnostic pop")
- #else
--static int
--YYID (yyi)
-- int yyi;
-+# define YY_INITIAL_VALUE(Value) Value
- #endif
--{
-- return yyi;
--}
-+#ifndef YY_IGNORE_MAYBE_UNINITIALIZED_BEGIN
-+# define YY_IGNORE_MAYBE_UNINITIALIZED_BEGIN
-+# define YY_IGNORE_MAYBE_UNINITIALIZED_END
-+#endif
-+#ifndef YY_INITIAL_VALUE
-+# define YY_INITIAL_VALUE(Value) /* Nothing. */
- #endif
-
-+
- #if ! defined yyoverflow || YYERROR_VERBOSE
-
- /* The parser invokes alloca or malloc; define the necessary symbols. */
-@@ -297,9 +320,9 @@ YYID (yyi)
- # define alloca _alloca
- # else
- # define YYSTACK_ALLOC alloca
--# if ! defined _ALLOCA_H && ! defined EXIT_SUCCESS && (defined __STDC__ || defined __C99__FUNC__ \
-- || defined __cplusplus || defined _MSC_VER)
-+# if ! defined _ALLOCA_H && ! defined EXIT_SUCCESS
- # include <stdlib.h> /* INFRINGES ON USER NAME SPACE */
-+ /* Use EXIT_SUCCESS as a witness for stdlib.h. */
- # ifndef EXIT_SUCCESS
- # define EXIT_SUCCESS 0
- # endif
-@@ -309,8 +332,8 @@ YYID (yyi)
- # endif
-
- # ifdef YYSTACK_ALLOC
-- /* Pacify GCC's `empty if-body' warning. */
--# define YYSTACK_FREE(Ptr) do { /* empty */; } while (YYID (0))
-+ /* Pacify GCC's 'empty if-body' warning. */
-+# define YYSTACK_FREE(Ptr) do { /* empty */; } while (0)
- # ifndef YYSTACK_ALLOC_MAXIMUM
- /* The OS might guarantee only one guard page at the bottom of the stack,
- and a page size can be as small as 4096 bytes. So we cannot safely
-@@ -326,7 +349,7 @@ YYID (yyi)
- # endif
- # if (defined __cplusplus && ! defined EXIT_SUCCESS \
- && ! ((defined YYMALLOC || defined malloc) \
-- && (defined YYFREE || defined free)))
-+ && (defined YYFREE || defined free)))
- # include <stdlib.h> /* INFRINGES ON USER NAME SPACE */
- # ifndef EXIT_SUCCESS
- # define EXIT_SUCCESS 0
-@@ -334,15 +357,13 @@ YYID (yyi)
- # endif
- # ifndef YYMALLOC
- # define YYMALLOC malloc
--# if ! defined malloc && ! defined EXIT_SUCCESS && (defined __STDC__ || defined __C99__FUNC__ \
-- || defined __cplusplus || defined _MSC_VER)
-+# if ! defined malloc && ! defined EXIT_SUCCESS
- void *malloc (YYSIZE_T); /* INFRINGES ON USER NAME SPACE */
- # endif
- # endif
- # ifndef YYFREE
- # define YYFREE free
--# if ! defined free && ! defined EXIT_SUCCESS && (defined __STDC__ || defined __C99__FUNC__ \
-- || defined __cplusplus || defined _MSC_VER)
-+# if ! defined free && ! defined EXIT_SUCCESS
- void free (void *); /* INFRINGES ON USER NAME SPACE */
- # endif
- # endif
-@@ -352,8 +373,8 @@ void free (void *); /* INFRINGES ON USER
-
- #if (! defined yyoverflow \
- && (! defined __cplusplus \
-- || (defined YYLTYPE_IS_TRIVIAL && YYLTYPE_IS_TRIVIAL \
-- && defined YYSTYPE_IS_TRIVIAL && YYSTYPE_IS_TRIVIAL)))
-+ || (defined YYLTYPE_IS_TRIVIAL && YYLTYPE_IS_TRIVIAL \
-+ && defined YYSTYPE_IS_TRIVIAL && YYSTYPE_IS_TRIVIAL)))
-
- /* A type that is properly aligned for any stack member. */
- union yyalloc
-@@ -379,35 +400,35 @@ union yyalloc
- elements in the stack, and YYPTR gives the new location of the
- stack. Advance YYPTR to a properly aligned location for the next
- stack. */
--# define YYSTACK_RELOCATE(Stack_alloc, Stack) \
-- do \
-- { \
-- YYSIZE_T yynewbytes; \
-- YYCOPY (&yyptr->Stack_alloc, Stack, yysize); \
-- Stack = &yyptr->Stack_alloc; \
-- yynewbytes = yystacksize * sizeof (*Stack) + YYSTACK_GAP_MAXIMUM; \
-- yyptr += yynewbytes / sizeof (*yyptr); \
-- } \
-- while (YYID (0))
-+# define YYSTACK_RELOCATE(Stack_alloc, Stack) \
-+ do \
-+ { \
-+ YYSIZE_T yynewbytes; \
-+ YYCOPY (&yyptr->Stack_alloc, Stack, yysize); \
-+ Stack = &yyptr->Stack_alloc; \
-+ yynewbytes = yystacksize * sizeof (*Stack) + YYSTACK_GAP_MAXIMUM; \
-+ yyptr += yynewbytes / sizeof (*yyptr); \
-+ } \
-+ while (0)
-
- #endif
-
- #if defined YYCOPY_NEEDED && YYCOPY_NEEDED
--/* Copy COUNT objects from FROM to TO. The source and destination do
-+/* Copy COUNT objects from SRC to DST. The source and destination do
- not overlap. */
- # ifndef YYCOPY
- # if defined __GNUC__ && 1 < __GNUC__
--# define YYCOPY(To, From, Count) \
-- __builtin_memcpy (To, From, (Count) * sizeof (*(From)))
-+# define YYCOPY(Dst, Src, Count) \
-+ __builtin_memcpy (Dst, Src, (Count) * sizeof (*(Src)))
- # else
--# define YYCOPY(To, From, Count) \
-- do \
-- { \
-- YYSIZE_T yyi; \
-- for (yyi = 0; yyi < (Count); yyi++) \
-- (To)[yyi] = (From)[yyi]; \
-- } \
-- while (YYID (0))
-+# define YYCOPY(Dst, Src, Count) \
-+ do \
-+ { \
-+ YYSIZE_T yyi; \
-+ for (yyi = 0; yyi < (Count); yyi++) \
-+ (Dst)[yyi] = (Src)[yyi]; \
-+ } \
-+ while (0)
- # endif
- # endif
- #endif /* !YYCOPY_NEEDED */
-@@ -418,37 +439,39 @@ union yyalloc
- #define YYLAST 136
-
- /* YYNTOKENS -- Number of terminals. */
--#define YYNTOKENS 48
-+#define YYNTOKENS 47
- /* YYNNTS -- Number of nonterminals. */
--#define YYNNTS 29
-+#define YYNNTS 28
- /* YYNRULES -- Number of rules. */
--#define YYNRULES 82
--/* YYNRULES -- Number of states. */
--#define YYNSTATES 147
-+#define YYNRULES 80
-+/* YYNSTATES -- Number of states. */
-+#define YYNSTATES 144
-
--/* YYTRANSLATE(YYLEX) -- Bison symbol number corresponding to YYLEX. */
-+/* YYTRANSLATE[YYX] -- Symbol number corresponding to YYX as returned
-+ by yylex, with out-of-bounds checking. */
- #define YYUNDEFTOK 2
--#define YYMAXUTOK 279
-+#define YYMAXUTOK 278
-
--#define YYTRANSLATE(YYX) \
-+#define YYTRANSLATE(YYX) \
- ((unsigned int) (YYX) <= YYMAXUTOK ? yytranslate[YYX] : YYUNDEFTOK)
-
--/* YYTRANSLATE[YYLEX] -- Bison symbol number corresponding to YYLEX. */
-+/* YYTRANSLATE[TOKEN-NUM] -- Symbol number corresponding to TOKEN-NUM
-+ as returned by yylex, without out-of-bounds checking. */
- static const yytype_uint8 yytranslate[] =
- {
- 0, 2, 2, 2, 2, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
-- 2, 2, 2, 47, 2, 2, 2, 45, 41, 2,
-- 33, 35, 44, 42, 34, 43, 2, 26, 2, 2,
-- 2, 2, 2, 2, 2, 2, 2, 2, 38, 25,
-- 36, 29, 30, 37, 2, 2, 2, 2, 2, 2,
-+ 2, 2, 2, 46, 2, 2, 2, 44, 40, 2,
-+ 32, 34, 43, 41, 33, 42, 2, 25, 2, 2,
-+ 2, 2, 2, 2, 2, 2, 2, 2, 37, 24,
-+ 35, 28, 29, 36, 2, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
-- 2, 31, 2, 32, 40, 2, 2, 2, 2, 2,
-+ 2, 30, 2, 31, 39, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
-- 2, 2, 2, 27, 39, 28, 46, 2, 2, 2,
-+ 2, 2, 2, 26, 38, 27, 45, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
-@@ -463,335 +486,292 @@ static const yytype_uint8 yytranslate[]
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 1, 2, 3, 4,
- 5, 6, 7, 8, 9, 10, 11, 12, 13, 14,
-- 15, 16, 17, 18, 19, 20, 21, 22, 23, 24
-+ 15, 16, 17, 18, 19, 20, 21, 22, 23
- };
-
- #if YYDEBUG
--/* YYPRHS[YYN] -- Index of the first RHS symbol of rule number YYN in
-- YYRHS. */
--static const yytype_uint16 yyprhs[] =
--{
-- 0, 0, 3, 9, 10, 13, 14, 17, 22, 25,
-- 28, 32, 37, 41, 46, 52, 53, 56, 61, 64,
-- 68, 71, 74, 78, 83, 86, 96, 102, 105, 106,
-- 109, 112, 116, 118, 121, 124, 127, 129, 131, 135,
-- 137, 139, 145, 147, 151, 153, 157, 159, 163, 165,
-- 169, 171, 175, 177, 181, 185, 187, 191, 195, 199,
-- 203, 207, 211, 213, 217, 221, 223, 227, 231, 235,
-- 237, 239, 242, 245, 248, 249, 252, 255, 256, 259,
-- 262, 265, 269
--};
--
--/* YYRHS -- A `-1'-separated list of the rules' RHS. */
--static const yytype_int8 yyrhs[] =
--{
-- 49, 0, -1, 3, 25, 50, 51, 53, -1, -1,
-- 4, 25, -1, -1, 52, 51, -1, 5, 60, 60,
-- 25, -1, 22, 52, -1, 26, 54, -1, 53, 26,
-- 54, -1, 53, 22, 23, 54, -1, 53, 23, 54,
-- -1, 53, 16, 23, 25, -1, 27, 55, 75, 28,
-- 25, -1, -1, 55, 56, -1, 17, 29, 57, 25,
-- -1, 17, 25, -1, 15, 17, 25, -1, 22, 56,
-- -1, 58, 21, -1, 58, 59, 30, -1, 58, 31,
-- 74, 32, -1, 58, 23, -1, 58, 24, 33, 21,
-- 34, 60, 34, 60, 35, -1, 58, 24, 33, 21,
-- 35, -1, 57, 22, -1, -1, 57, 34, -1, 58,
-- 22, -1, 14, 18, 36, -1, 36, -1, 59, 60,
-- -1, 59, 23, -1, 59, 22, -1, 18, -1, 19,
-- -1, 33, 61, 35, -1, 62, -1, 63, -1, 63,
-- 37, 61, 38, 62, -1, 64, -1, 63, 13, 64,
-- -1, 65, -1, 64, 12, 65, -1, 66, -1, 65,
-- 39, 66, -1, 67, -1, 66, 40, 67, -1, 68,
-- -1, 67, 41, 68, -1, 69, -1, 68, 10, 69,
-- -1, 68, 11, 69, -1, 70, -1, 69, 36, 70,
-- -1, 69, 30, 70, -1, 69, 8, 70, -1, 69,
-- 9, 70, -1, 70, 6, 71, -1, 70, 7, 71,
-- -1, 71, -1, 71, 42, 72, -1, 71, 43, 72,
-- -1, 72, -1, 72, 44, 73, -1, 72, 26, 73,
-- -1, 72, 45, 73, -1, 73, -1, 60, -1, 43,
-- 73, -1, 46, 73, -1, 47, 73, -1, -1, 74,
-- 20, -1, 74, 22, -1, -1, 76, 75, -1, 76,
-- 56, -1, 17, 54, -1, 16, 17, 25, -1, 22,
-- 76, -1
--};
--
--/* YYRLINE[YYN] -- source line where rule number YYN was defined. */
-+ /* YYRLINE[YYN] -- Source line where rule number YYN was defined. */
- static const yytype_uint16 yyrline[] =
- {
-- 0, 108, 108, 119, 122, 130, 133, 140, 144, 152,
-- 156, 161, 172, 182, 197, 205, 208, 215, 219, 223,
-- 227, 235, 239, 243, 247, 251, 267, 277, 285, 288,
-- 292, 299, 315, 320, 339, 353, 360, 361, 362, 369,
-- 373, 374, 378, 379, 383, 384, 388, 389, 393, 394,
-- 398, 399, 403, 404, 405, 409, 410, 411, 412, 413,
-- 417, 418, 419, 423, 424, 425, 429, 430, 431, 432,
-- 436, 437, 438, 439, 444, 447, 451, 459, 462, 466,
-- 474, 478, 482
-+ 0, 104, 104, 113, 116, 123, 127, 135, 139, 144,
-+ 155, 165, 180, 188, 191, 198, 202, 206, 210, 218,
-+ 222, 226, 230, 234, 250, 260, 268, 271, 275, 282,
-+ 298, 303, 322, 336, 343, 344, 345, 352, 356, 357,
-+ 361, 362, 366, 367, 371, 372, 376, 377, 381, 382,
-+ 386, 387, 388, 392, 393, 394, 395, 396, 400, 401,
-+ 402, 406, 407, 408, 412, 413, 414, 415, 419, 420,
-+ 421, 422, 427, 430, 434, 442, 445, 449, 457, 461,
-+ 465
- };
- #endif
-
--#if YYDEBUG || YYERROR_VERBOSE || YYTOKEN_TABLE
-+#if YYDEBUG || YYERROR_VERBOSE || 0
- /* YYTNAME[SYMBOL-NUM] -- String name of the symbol SYMBOL-NUM.
- First, the terminals, then, starting at YYNTOKENS, nonterminals. */
- static const char *const yytname[] =
- {
-- "$end", "error", "$undefined", "DT_V1", "DT_PLUGIN", "DT_MEMRESERVE",
-- "DT_LSHIFT", "DT_RSHIFT", "DT_LE", "DT_GE", "DT_EQ", "DT_NE", "DT_AND",
-- "DT_OR", "DT_BITS", "DT_DEL_PROP", "DT_DEL_NODE", "DT_PROPNODENAME",
-- "DT_LITERAL", "DT_CHAR_LITERAL", "DT_BYTE", "DT_STRING", "DT_LABEL",
-- "DT_REF", "DT_INCBIN", "';'", "'/'", "'{'", "'}'", "'='", "'>'", "'['",
-- "']'", "'('", "','", "')'", "'<'", "'?'", "':'", "'|'", "'^'", "'&'",
-- "'+'", "'-'", "'*'", "'%'", "'~'", "'!'", "$accept", "sourcefile",
-- "plugindecl", "memreserves", "memreserve", "devicetree", "nodedef",
-- "proplist", "propdef", "propdata", "propdataprefix", "arrayprefix",
-- "integer_prim", "integer_expr", "integer_trinary", "integer_or",
-- "integer_and", "integer_bitor", "integer_bitxor", "integer_bitand",
-- "integer_eq", "integer_rela", "integer_shift", "integer_add",
-- "integer_mul", "integer_unary", "bytestring", "subnodes", "subnode", 0
-+ "$end", "error", "$undefined", "DT_V1", "DT_MEMRESERVE", "DT_LSHIFT",
-+ "DT_RSHIFT", "DT_LE", "DT_GE", "DT_EQ", "DT_NE", "DT_AND", "DT_OR",
-+ "DT_BITS", "DT_DEL_PROP", "DT_DEL_NODE", "DT_PROPNODENAME", "DT_LITERAL",
-+ "DT_CHAR_LITERAL", "DT_BYTE", "DT_STRING", "DT_LABEL", "DT_REF",
-+ "DT_INCBIN", "';'", "'/'", "'{'", "'}'", "'='", "'>'", "'['", "']'",
-+ "'('", "','", "')'", "'<'", "'?'", "':'", "'|'", "'^'", "'&'", "'+'",
-+ "'-'", "'*'", "'%'", "'~'", "'!'", "$accept", "sourcefile",
-+ "memreserves", "memreserve", "devicetree", "nodedef", "proplist",
-+ "propdef", "propdata", "propdataprefix", "arrayprefix", "integer_prim",
-+ "integer_expr", "integer_trinary", "integer_or", "integer_and",
-+ "integer_bitor", "integer_bitxor", "integer_bitand", "integer_eq",
-+ "integer_rela", "integer_shift", "integer_add", "integer_mul",
-+ "integer_unary", "bytestring", "subnodes", "subnode", YY_NULLPTR
- };
- #endif
-
- # ifdef YYPRINT
--/* YYTOKNUM[YYLEX-NUM] -- Internal token number corresponding to
-- token YYLEX-NUM. */
-+/* YYTOKNUM[NUM] -- (External) token number corresponding to the
-+ (internal) symbol number NUM (which must be that of a token). */
- static const yytype_uint16 yytoknum[] =
- {
- 0, 256, 257, 258, 259, 260, 261, 262, 263, 264,
- 265, 266, 267, 268, 269, 270, 271, 272, 273, 274,
-- 275, 276, 277, 278, 279, 59, 47, 123, 125, 61,
-- 62, 91, 93, 40, 44, 41, 60, 63, 58, 124,
-- 94, 38, 43, 45, 42, 37, 126, 33
-+ 275, 276, 277, 278, 59, 47, 123, 125, 61, 62,
-+ 91, 93, 40, 44, 41, 60, 63, 58, 124, 94,
-+ 38, 43, 45, 42, 37, 126, 33
- };
- # endif
-
--/* YYR1[YYN] -- Symbol number of symbol that rule YYN derives. */
--static const yytype_uint8 yyr1[] =
--{
-- 0, 48, 49, 50, 50, 51, 51, 52, 52, 53,
-- 53, 53, 53, 53, 54, 55, 55, 56, 56, 56,
-- 56, 57, 57, 57, 57, 57, 57, 57, 58, 58,
-- 58, 59, 59, 59, 59, 59, 60, 60, 60, 61,
-- 62, 62, 63, 63, 64, 64, 65, 65, 66, 66,
-- 67, 67, 68, 68, 68, 69, 69, 69, 69, 69,
-- 70, 70, 70, 71, 71, 71, 72, 72, 72, 72,
-- 73, 73, 73, 73, 74, 74, 74, 75, 75, 75,
-- 76, 76, 76
--};
-+#define YYPACT_NINF -81
-
--/* YYR2[YYN] -- Number of symbols composing right hand side of rule YYN. */
--static const yytype_uint8 yyr2[] =
-+#define yypact_value_is_default(Yystate) \
-+ (!!((Yystate) == (-81)))
-+
-+#define YYTABLE_NINF -1
-+
-+#define yytable_value_is_error(Yytable_value) \
-+ 0
-+
-+ /* YYPACT[STATE-NUM] -- Index in YYTABLE of the portion describing
-+ STATE-NUM. */
-+static const yytype_int8 yypact[] =
- {
-- 0, 2, 5, 0, 2, 0, 2, 4, 2, 2,
-- 3, 4, 3, 4, 5, 0, 2, 4, 2, 3,
-- 2, 2, 3, 4, 2, 9, 5, 2, 0, 2,
-- 2, 3, 1, 2, 2, 2, 1, 1, 3, 1,
-- 1, 5, 1, 3, 1, 3, 1, 3, 1, 3,
-- 1, 3, 1, 3, 3, 1, 3, 3, 3, 3,
-- 3, 3, 1, 3, 3, 1, 3, 3, 3, 1,
-- 1, 2, 2, 2, 0, 2, 2, 0, 2, 2,
-- 2, 3, 2
-+ 16, -11, 21, 10, -81, 25, 10, 19, 10, -81,
-+ -81, -9, 25, -81, 2, 51, -81, -9, -9, -9,
-+ -81, 1, -81, -6, 50, 14, 28, 29, 36, 3,
-+ 58, 44, -3, -81, 47, -81, -81, 65, 68, 2,
-+ 2, -81, -81, -81, -81, -9, -9, -9, -9, -9,
-+ -9, -9, -9, -9, -9, -9, -9, -9, -9, -9,
-+ -9, -9, -9, -9, -81, 63, 69, 2, -81, -81,
-+ 50, 57, 14, 28, 29, 36, 3, 3, 58, 58,
-+ 58, 58, 44, 44, -3, -3, -81, -81, -81, 79,
-+ 80, -8, 63, -81, 72, 63, -81, -81, -9, 76,
-+ 77, -81, -81, -81, -81, -81, 78, -81, -81, -81,
-+ -81, -81, 35, 4, -81, -81, -81, -81, 86, -81,
-+ -81, -81, 73, -81, -81, 33, 71, 84, 39, -81,
-+ -81, -81, -81, -81, 41, -81, -81, -81, 25, -81,
-+ 74, 25, 75, -81
- };
-
--/* YYDEFACT[STATE-NAME] -- Default reduction number in state STATE-NUM.
-- Performed when YYTABLE doesn't specify something else to do. Zero
-- means the default is an error. */
-+ /* YYDEFACT[STATE-NUM] -- Default reduction number in state STATE-NUM.
-+ Performed when YYTABLE does not specify something else to do. Zero
-+ means the default is an error. */
- static const yytype_uint8 yydefact[] =
- {
-- 0, 0, 0, 3, 1, 0, 5, 4, 0, 0,
-- 0, 5, 36, 37, 0, 0, 8, 0, 2, 6,
-- 0, 0, 0, 70, 0, 39, 40, 42, 44, 46,
-- 48, 50, 52, 55, 62, 65, 69, 0, 15, 9,
-- 0, 0, 0, 0, 71, 72, 73, 38, 0, 0,
-+ 0, 0, 0, 3, 1, 0, 0, 0, 3, 34,
-+ 35, 0, 0, 6, 0, 2, 4, 0, 0, 0,
-+ 68, 0, 37, 38, 40, 42, 44, 46, 48, 50,
-+ 53, 60, 63, 67, 0, 13, 7, 0, 0, 0,
-+ 0, 69, 70, 71, 36, 0, 0, 0, 0, 0,
- 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
-- 0, 0, 0, 0, 0, 0, 0, 7, 77, 0,
-- 0, 12, 10, 43, 0, 45, 47, 49, 51, 53,
-- 54, 58, 59, 57, 56, 60, 61, 63, 64, 67,
-- 66, 68, 0, 0, 0, 0, 16, 0, 77, 13,
-- 11, 0, 0, 0, 18, 28, 80, 20, 82, 0,
-- 79, 78, 41, 19, 81, 0, 0, 14, 27, 17,
-- 29, 0, 21, 30, 24, 0, 74, 32, 0, 0,
-- 0, 0, 35, 34, 22, 33, 31, 0, 75, 76,
-- 23, 0, 26, 0, 0, 0, 25
-+ 0, 0, 0, 0, 5, 75, 0, 0, 10, 8,
-+ 41, 0, 43, 45, 47, 49, 51, 52, 56, 57,
-+ 55, 54, 58, 59, 61, 62, 65, 64, 66, 0,
-+ 0, 0, 0, 14, 0, 75, 11, 9, 0, 0,
-+ 0, 16, 26, 78, 18, 80, 0, 77, 76, 39,
-+ 17, 79, 0, 0, 12, 25, 15, 27, 0, 19,
-+ 28, 22, 0, 72, 30, 0, 0, 0, 0, 33,
-+ 32, 20, 31, 29, 0, 73, 74, 21, 0, 24,
-+ 0, 0, 0, 23
- };
-
--/* YYDEFGOTO[NTERM-NUM]. */
--static const yytype_int16 yydefgoto[] =
-+ /* YYPGOTO[NTERM-NUM]. */
-+static const yytype_int8 yypgoto[] =
- {
-- -1, 2, 6, 10, 11, 18, 39, 68, 96, 115,
-- 116, 128, 23, 24, 25, 26, 27, 28, 29, 30,
-- 31, 32, 33, 34, 35, 36, 131, 97, 98
-+ -81, -81, 100, 104, -81, -38, -81, -80, -81, -81,
-+ -81, -5, 66, 13, -81, 70, 67, 81, 64, 82,
-+ 37, 27, 34, 38, -14, -81, 22, 24
- };
-
--/* YYPACT[STATE-NUM] -- Index in YYTABLE of the portion describing
-- STATE-NUM. */
--#define YYPACT_NINF -84
--static const yytype_int8 yypact[] =
-+ /* YYDEFGOTO[NTERM-NUM]. */
-+static const yytype_int16 yydefgoto[] =
- {
-- 15, -12, 35, 42, -84, 27, 9, -84, 24, 9,
-- 43, 9, -84, -84, -10, 24, -84, 60, 44, -84,
-- -10, -10, -10, -84, 55, -84, -7, 52, 53, 51,
-- 54, 10, 2, 38, 37, -4, -84, 68, -84, -84,
-- 71, 73, 60, 60, -84, -84, -84, -84, -10, -10,
-- -10, -10, -10, -10, -10, -10, -10, -10, -10, -10,
-- -10, -10, -10, -10, -10, -10, -10, -84, 56, 72,
-- 60, -84, -84, 52, 61, 53, 51, 54, 10, 2,
-- 2, 38, 38, 38, 38, 37, 37, -4, -4, -84,
-- -84, -84, 81, 83, 34, 56, -84, 74, 56, -84,
-- -84, -10, 76, 78, -84, -84, -84, -84, -84, 79,
-- -84, -84, -84, -84, -84, -6, 3, -84, -84, -84,
-- -84, 87, -84, -84, -84, 75, -84, -84, 32, 70,
-- 86, 36, -84, -84, -84, -84, -84, 47, -84, -84,
-- -84, 24, -84, 77, 24, 80, -84
-+ -1, 2, 7, 8, 15, 36, 65, 93, 112, 113,
-+ 125, 20, 21, 22, 23, 24, 25, 26, 27, 28,
-+ 29, 30, 31, 32, 33, 128, 94, 95
- };
-
--/* YYPGOTO[NTERM-NUM]. */
--static const yytype_int8 yypgoto[] =
-+ /* YYTABLE[YYPACT[STATE-NUM]] -- What to do in state STATE-NUM. If
-+ positive, shift that token. If negative, reduce the rule whose
-+ number is the opposite. If YYTABLE_NINF, syntax error. */
-+static const yytype_uint8 yytable[] =
- {
-- -84, -84, -84, 98, 101, -84, -41, -84, -83, -84,
-- -84, -84, -8, 63, 12, -84, 66, 67, 65, 69,
-- 82, 29, 18, 25, 26, -17, -84, 20, 28
-+ 12, 68, 69, 41, 42, 43, 45, 34, 9, 10,
-+ 53, 54, 104, 3, 5, 107, 101, 118, 35, 1,
-+ 102, 4, 61, 11, 119, 120, 121, 122, 35, 97,
-+ 46, 6, 55, 17, 123, 44, 18, 19, 56, 124,
-+ 62, 63, 9, 10, 14, 51, 52, 86, 87, 88,
-+ 9, 10, 48, 103, 129, 130, 115, 11, 135, 116,
-+ 136, 47, 131, 57, 58, 11, 37, 49, 117, 50,
-+ 137, 64, 38, 39, 138, 139, 40, 89, 90, 91,
-+ 78, 79, 80, 81, 92, 59, 60, 66, 76, 77,
-+ 67, 82, 83, 96, 98, 99, 100, 84, 85, 106,
-+ 110, 111, 114, 126, 134, 127, 133, 141, 16, 143,
-+ 13, 109, 71, 74, 72, 70, 105, 108, 0, 0,
-+ 132, 0, 0, 0, 0, 0, 0, 0, 0, 73,
-+ 0, 0, 75, 140, 0, 0, 142
- };
-
--/* YYTABLE[YYPACT[STATE-NUM]]. What to do in state STATE-NUM. If
-- positive, shift that token. If negative, reduce the rule which
-- number is the opposite. If YYTABLE_NINF, syntax error. */
--#define YYTABLE_NINF -1
--static const yytype_uint8 yytable[] =
-+static const yytype_int16 yycheck[] =
- {
-- 15, 71, 72, 44, 45, 46, 48, 37, 12, 13,
-- 56, 57, 107, 3, 8, 110, 118, 121, 1, 119,
-- 54, 55, 64, 14, 122, 123, 124, 125, 120, 100,
-- 49, 9, 58, 20, 126, 4, 21, 22, 59, 127,
-- 65, 66, 12, 13, 60, 61, 5, 89, 90, 91,
-- 12, 13, 7, 106, 132, 133, 138, 14, 139, 104,
-- 40, 38, 134, 105, 50, 14, 41, 42, 140, 17,
-- 43, 92, 93, 94, 81, 82, 83, 84, 95, 62,
-- 63, 141, 142, 79, 80, 85, 86, 38, 87, 88,
-- 47, 52, 51, 67, 69, 53, 70, 99, 102, 101,
-- 103, 113, 109, 114, 117, 129, 136, 137, 130, 19,
-- 16, 144, 74, 112, 73, 146, 76, 75, 111, 0,
-- 135, 77, 0, 108, 0, 0, 0, 0, 0, 0,
-- 0, 0, 0, 143, 0, 78, 145
-+ 5, 39, 40, 17, 18, 19, 12, 12, 17, 18,
-+ 7, 8, 92, 24, 4, 95, 24, 13, 26, 3,
-+ 28, 0, 25, 32, 20, 21, 22, 23, 26, 67,
-+ 36, 21, 29, 42, 30, 34, 45, 46, 35, 35,
-+ 43, 44, 17, 18, 25, 9, 10, 61, 62, 63,
-+ 17, 18, 38, 91, 21, 22, 21, 32, 19, 24,
-+ 21, 11, 29, 5, 6, 32, 15, 39, 33, 40,
-+ 31, 24, 21, 22, 33, 34, 25, 14, 15, 16,
-+ 53, 54, 55, 56, 21, 41, 42, 22, 51, 52,
-+ 22, 57, 58, 24, 37, 16, 16, 59, 60, 27,
-+ 24, 24, 24, 17, 20, 32, 35, 33, 8, 34,
-+ 6, 98, 46, 49, 47, 45, 92, 95, -1, -1,
-+ 125, -1, -1, -1, -1, -1, -1, -1, -1, 48,
-+ -1, -1, 50, 138, -1, -1, 141
- };
-
--#define yypact_value_is_default(yystate) \
-- ((yystate) == (-84))
--
--#define yytable_value_is_error(yytable_value) \
-- YYID (0)
-+ /* YYSTOS[STATE-NUM] -- The (internal number of the) accessing
-+ symbol of state STATE-NUM. */
-+static const yytype_uint8 yystos[] =
-+{
-+ 0, 3, 48, 24, 0, 4, 21, 49, 50, 17,
-+ 18, 32, 58, 50, 25, 51, 49, 42, 45, 46,
-+ 58, 59, 60, 61, 62, 63, 64, 65, 66, 67,
-+ 68, 69, 70, 71, 58, 26, 52, 15, 21, 22,
-+ 25, 71, 71, 71, 34, 12, 36, 11, 38, 39,
-+ 40, 9, 10, 7, 8, 29, 35, 5, 6, 41,
-+ 42, 25, 43, 44, 24, 53, 22, 22, 52, 52,
-+ 62, 59, 63, 64, 65, 66, 67, 67, 68, 68,
-+ 68, 68, 69, 69, 70, 70, 71, 71, 71, 14,
-+ 15, 16, 21, 54, 73, 74, 24, 52, 37, 16,
-+ 16, 24, 28, 52, 54, 74, 27, 54, 73, 60,
-+ 24, 24, 55, 56, 24, 21, 24, 33, 13, 20,
-+ 21, 22, 23, 30, 35, 57, 17, 32, 72, 21,
-+ 22, 29, 58, 35, 20, 19, 21, 31, 33, 34,
-+ 58, 33, 58, 34
-+};
-
--static const yytype_int16 yycheck[] =
-+ /* YYR1[YYN] -- Symbol number of symbol that rule YYN derives. */
-+static const yytype_uint8 yyr1[] =
- {
-- 8, 42, 43, 20, 21, 22, 13, 15, 18, 19,
-- 8, 9, 95, 25, 5, 98, 22, 14, 3, 25,
-- 10, 11, 26, 33, 21, 22, 23, 24, 34, 70,
-- 37, 22, 30, 43, 31, 0, 46, 47, 36, 36,
-- 44, 45, 18, 19, 6, 7, 4, 64, 65, 66,
-- 18, 19, 25, 94, 22, 23, 20, 33, 22, 25,
-- 16, 27, 30, 29, 12, 33, 22, 23, 32, 26,
-- 26, 15, 16, 17, 56, 57, 58, 59, 22, 42,
-- 43, 34, 35, 54, 55, 60, 61, 27, 62, 63,
-- 35, 40, 39, 25, 23, 41, 23, 25, 17, 38,
-- 17, 25, 28, 25, 25, 18, 36, 21, 33, 11,
-- 9, 34, 49, 101, 48, 35, 51, 50, 98, -1,
-- 128, 52, -1, 95, -1, -1, -1, -1, -1, -1,
-- -1, -1, -1, 141, -1, 53, 144
-+ 0, 47, 48, 49, 49, 50, 50, 51, 51, 51,
-+ 51, 51, 52, 53, 53, 54, 54, 54, 54, 55,
-+ 55, 55, 55, 55, 55, 55, 56, 56, 56, 57,
-+ 57, 57, 57, 57, 58, 58, 58, 59, 60, 60,
-+ 61, 61, 62, 62, 63, 63, 64, 64, 65, 65,
-+ 66, 66, 66, 67, 67, 67, 67, 67, 68, 68,
-+ 68, 69, 69, 69, 70, 70, 70, 70, 71, 71,
-+ 71, 71, 72, 72, 72, 73, 73, 73, 74, 74,
-+ 74
- };
-
--/* YYSTOS[STATE-NUM] -- The (internal number of the) accessing
-- symbol of state STATE-NUM. */
--static const yytype_uint8 yystos[] =
-+ /* YYR2[YYN] -- Number of symbols on the right hand side of rule YYN. */
-+static const yytype_uint8 yyr2[] =
- {
-- 0, 3, 49, 25, 0, 4, 50, 25, 5, 22,
-- 51, 52, 18, 19, 33, 60, 52, 26, 53, 51,
-- 43, 46, 47, 60, 61, 62, 63, 64, 65, 66,
-- 67, 68, 69, 70, 71, 72, 73, 60, 27, 54,
-- 16, 22, 23, 26, 73, 73, 73, 35, 13, 37,
-- 12, 39, 40, 41, 10, 11, 8, 9, 30, 36,
-- 6, 7, 42, 43, 26, 44, 45, 25, 55, 23,
-- 23, 54, 54, 64, 61, 65, 66, 67, 68, 69,
-- 69, 70, 70, 70, 70, 71, 71, 72, 72, 73,
-- 73, 73, 15, 16, 17, 22, 56, 75, 76, 25,
-- 54, 38, 17, 17, 25, 29, 54, 56, 76, 28,
-- 56, 75, 62, 25, 25, 57, 58, 25, 22, 25,
-- 34, 14, 21, 22, 23, 24, 31, 36, 59, 18,
-- 33, 74, 22, 23, 30, 60, 36, 21, 20, 22,
-- 32, 34, 35, 60, 34, 60, 35
-+ 0, 2, 4, 0, 2, 4, 2, 2, 3, 4,
-+ 3, 4, 5, 0, 2, 4, 2, 3, 2, 2,
-+ 3, 4, 2, 9, 5, 2, 0, 2, 2, 3,
-+ 1, 2, 2, 2, 1, 1, 3, 1, 1, 5,
-+ 1, 3, 1, 3, 1, 3, 1, 3, 1, 3,
-+ 1, 3, 3, 1, 3, 3, 3, 3, 3, 3,
-+ 1, 3, 3, 1, 3, 3, 3, 1, 1, 2,
-+ 2, 2, 0, 2, 2, 0, 2, 2, 2, 3,
-+ 2
- };
-
--#define yyerrok (yyerrstatus = 0)
--#define yyclearin (yychar = YYEMPTY)
--#define YYEMPTY (-2)
--#define YYEOF 0
--
--#define YYACCEPT goto yyacceptlab
--#define YYABORT goto yyabortlab
--#define YYERROR goto yyerrorlab
--
--
--/* Like YYERROR except do call yyerror. This remains here temporarily
-- to ease the transition to the new meaning of YYERROR, for GCC.
-- Once GCC version 2 has supplanted version 1, this can go. However,
-- YYFAIL appears to be in use. Nevertheless, it is formally deprecated
-- in Bison 2.4.2's NEWS entry, where a plan to phase it out is
-- discussed. */
--
--#define YYFAIL goto yyerrlab
--#if defined YYFAIL
-- /* This is here to suppress warnings from the GCC cpp's
-- -Wunused-macros. Normally we don't worry about that warning, but
-- some users do, and we want to make it easy for users to remove
-- YYFAIL uses, which will produce warnings from Bison 2.5. */
--#endif
-
--#define YYRECOVERING() (!!yyerrstatus)
-+#define yyerrok (yyerrstatus = 0)
-+#define yyclearin (yychar = YYEMPTY)
-+#define YYEMPTY (-2)
-+#define YYEOF 0
-+
-+#define YYACCEPT goto yyacceptlab
-+#define YYABORT goto yyabortlab
-+#define YYERROR goto yyerrorlab
-
--#define YYBACKUP(Token, Value) \
--do \
-- if (yychar == YYEMPTY && yylen == 1) \
-- { \
-- yychar = (Token); \
-- yylval = (Value); \
-- YYPOPSTACK (1); \
-- goto yybackup; \
-- } \
-- else \
-- { \
-- yyerror (YY_("syntax error: cannot back up")); \
-- YYERROR; \
-- } \
--while (YYID (0))
-
-+#define YYRECOVERING() (!!yyerrstatus)
-
--#define YYTERROR 1
--#define YYERRCODE 256
-+#define YYBACKUP(Token, Value) \
-+do \
-+ if (yychar == YYEMPTY) \
-+ { \
-+ yychar = (Token); \
-+ yylval = (Value); \
-+ YYPOPSTACK (yylen); \
-+ yystate = *yyssp; \
-+ goto yybackup; \
-+ } \
-+ else \
-+ { \
-+ yyerror (YY_("syntax error: cannot back up")); \
-+ YYERROR; \
-+ } \
-+while (0)
-+
-+/* Error token number */
-+#define YYTERROR 1
-+#define YYERRCODE 256
-
-
- /* YYLLOC_DEFAULT -- Set CURRENT to span from RHS[1] to RHS[N].
- If N is 0, then set CURRENT to the empty location which ends
- the previous symbol: RHS[0] (always defined). */
-
--#define YYRHSLOC(Rhs, K) ((Rhs)[K])
- #ifndef YYLLOC_DEFAULT
--# define YYLLOC_DEFAULT(Current, Rhs, N) \
-- do \
-- if (YYID (N)) \
-- { \
-- (Current).first_line = YYRHSLOC (Rhs, 1).first_line; \
-- (Current).first_column = YYRHSLOC (Rhs, 1).first_column; \
-- (Current).last_line = YYRHSLOC (Rhs, N).last_line; \
-- (Current).last_column = YYRHSLOC (Rhs, N).last_column; \
-- } \
-- else \
-- { \
-- (Current).first_line = (Current).last_line = \
-- YYRHSLOC (Rhs, 0).last_line; \
-- (Current).first_column = (Current).last_column = \
-- YYRHSLOC (Rhs, 0).last_column; \
-- } \
-- while (YYID (0))
-+# define YYLLOC_DEFAULT(Current, Rhs, N) \
-+ do \
-+ if (N) \
-+ { \
-+ (Current).first_line = YYRHSLOC (Rhs, 1).first_line; \
-+ (Current).first_column = YYRHSLOC (Rhs, 1).first_column; \
-+ (Current).last_line = YYRHSLOC (Rhs, N).last_line; \
-+ (Current).last_column = YYRHSLOC (Rhs, N).last_column; \
-+ } \
-+ else \
-+ { \
-+ (Current).first_line = (Current).last_line = \
-+ YYRHSLOC (Rhs, 0).last_line; \
-+ (Current).first_column = (Current).last_column = \
-+ YYRHSLOC (Rhs, 0).last_column; \
-+ } \
-+ while (0)
- #endif
-
-+#define YYRHSLOC(Rhs, K) ((Rhs)[K])
-+
-+
-+/* Enable debugging if requested. */
-+#if YYDEBUG
-+
-+# ifndef YYFPRINTF
-+# include <stdio.h> /* INFRINGES ON USER NAME SPACE */
-+# define YYFPRINTF fprintf
-+# endif
-+
-+# define YYDPRINTF(Args) \
-+do { \
-+ if (yydebug) \
-+ YYFPRINTF Args; \
-+} while (0)
-+
-
- /* YY_LOCATION_PRINT -- Print the location on the stream.
- This macro was not mandated originally: define only if we know
-@@ -799,82 +779,73 @@ while (YYID (0))
-
- #ifndef YY_LOCATION_PRINT
- # if defined YYLTYPE_IS_TRIVIAL && YYLTYPE_IS_TRIVIAL
--# define YY_LOCATION_PRINT(File, Loc) \
-- fprintf (File, "%d.%d-%d.%d", \
-- (Loc).first_line, (Loc).first_column, \
-- (Loc).last_line, (Loc).last_column)
--# else
--# define YY_LOCATION_PRINT(File, Loc) ((void) 0)
--# endif
--#endif
--
-
--/* YYLEX -- calling `yylex' with the right arguments. */
-+/* Print *YYLOCP on YYO. Private, do not rely on its existence. */
-
--#ifdef YYLEX_PARAM
--# define YYLEX yylex (YYLEX_PARAM)
--#else
--# define YYLEX yylex ()
--#endif
-+YY_ATTRIBUTE_UNUSED
-+static unsigned
-+yy_location_print_ (FILE *yyo, YYLTYPE const * const yylocp)
-+{
-+ unsigned res = 0;
-+ int end_col = 0 != yylocp->last_column ? yylocp->last_column - 1 : 0;
-+ if (0 <= yylocp->first_line)
-+ {
-+ res += YYFPRINTF (yyo, "%d", yylocp->first_line);
-+ if (0 <= yylocp->first_column)
-+ res += YYFPRINTF (yyo, ".%d", yylocp->first_column);
-+ }
-+ if (0 <= yylocp->last_line)
-+ {
-+ if (yylocp->first_line < yylocp->last_line)
-+ {
-+ res += YYFPRINTF (yyo, "-%d", yylocp->last_line);
-+ if (0 <= end_col)
-+ res += YYFPRINTF (yyo, ".%d", end_col);
-+ }
-+ else if (0 <= end_col && yylocp->first_column < end_col)
-+ res += YYFPRINTF (yyo, "-%d", end_col);
-+ }
-+ return res;
-+ }
-
--/* Enable debugging if requested. */
--#if YYDEBUG
-+# define YY_LOCATION_PRINT(File, Loc) \
-+ yy_location_print_ (File, &(Loc))
-
--# ifndef YYFPRINTF
--# include <stdio.h> /* INFRINGES ON USER NAME SPACE */
--# define YYFPRINTF fprintf
-+# else
-+# define YY_LOCATION_PRINT(File, Loc) ((void) 0)
- # endif
-+#endif
-
--# define YYDPRINTF(Args) \
--do { \
-- if (yydebug) \
-- YYFPRINTF Args; \
--} while (YYID (0))
--
--# define YY_SYMBOL_PRINT(Title, Type, Value, Location) \
--do { \
-- if (yydebug) \
-- { \
-- YYFPRINTF (stderr, "%s ", Title); \
-- yy_symbol_print (stderr, \
-- Type, Value, Location); \
-- YYFPRINTF (stderr, "\n"); \
-- } \
--} while (YYID (0))
-
-+# define YY_SYMBOL_PRINT(Title, Type, Value, Location) \
-+do { \
-+ if (yydebug) \
-+ { \
-+ YYFPRINTF (stderr, "%s ", Title); \
-+ yy_symbol_print (stderr, \
-+ Type, Value, Location); \
-+ YYFPRINTF (stderr, "\n"); \
-+ } \
-+} while (0)
-
--/*--------------------------------.
--| Print this symbol on YYOUTPUT. |
--`--------------------------------*/
-
--/*ARGSUSED*/
--#if (defined __STDC__ || defined __C99__FUNC__ \
-- || defined __cplusplus || defined _MSC_VER)
-+/*----------------------------------------.
-+| Print this symbol's value on YYOUTPUT. |
-+`----------------------------------------*/
-+
- static void
- yy_symbol_value_print (FILE *yyoutput, int yytype, YYSTYPE const * const yyvaluep, YYLTYPE const * const yylocationp)
--#else
--static void
--yy_symbol_value_print (yyoutput, yytype, yyvaluep, yylocationp)
-- FILE *yyoutput;
-- int yytype;
-- YYSTYPE const * const yyvaluep;
-- YYLTYPE const * const yylocationp;
--#endif
- {
-+ FILE *yyo = yyoutput;
-+ YYUSE (yyo);
-+ YYUSE (yylocationp);
- if (!yyvaluep)
- return;
-- YYUSE (yylocationp);
- # ifdef YYPRINT
- if (yytype < YYNTOKENS)
- YYPRINT (yyoutput, yytoknum[yytype], *yyvaluep);
--# else
-- YYUSE (yyoutput);
- # endif
-- switch (yytype)
-- {
-- default:
-- break;
-- }
-+ YYUSE (yytype);
- }
-
-
-@@ -882,23 +853,11 @@ yy_symbol_value_print (yyoutput, yytype,
- | Print this symbol on YYOUTPUT. |
- `--------------------------------*/
-
--#if (defined __STDC__ || defined __C99__FUNC__ \
-- || defined __cplusplus || defined _MSC_VER)
- static void
- yy_symbol_print (FILE *yyoutput, int yytype, YYSTYPE const * const yyvaluep, YYLTYPE const * const yylocationp)
--#else
--static void
--yy_symbol_print (yyoutput, yytype, yyvaluep, yylocationp)
-- FILE *yyoutput;
-- int yytype;
-- YYSTYPE const * const yyvaluep;
-- YYLTYPE const * const yylocationp;
--#endif
- {
-- if (yytype < YYNTOKENS)
-- YYFPRINTF (yyoutput, "token %s (", yytname[yytype]);
-- else
-- YYFPRINTF (yyoutput, "nterm %s (", yytname[yytype]);
-+ YYFPRINTF (yyoutput, "%s %s (",
-+ yytype < YYNTOKENS ? "token" : "nterm", yytname[yytype]);
-
- YY_LOCATION_PRINT (yyoutput, *yylocationp);
- YYFPRINTF (yyoutput, ": ");
-@@ -911,16 +870,8 @@ yy_symbol_print (yyoutput, yytype, yyval
- | TOP (included). |
- `------------------------------------------------------------------*/
-
--#if (defined __STDC__ || defined __C99__FUNC__ \
-- || defined __cplusplus || defined _MSC_VER)
- static void
- yy_stack_print (yytype_int16 *yybottom, yytype_int16 *yytop)
--#else
--static void
--yy_stack_print (yybottom, yytop)
-- yytype_int16 *yybottom;
-- yytype_int16 *yytop;
--#endif
- {
- YYFPRINTF (stderr, "Stack now");
- for (; yybottom <= yytop; yybottom++)
-@@ -931,50 +882,42 @@ yy_stack_print (yybottom, yytop)
- YYFPRINTF (stderr, "\n");
- }
-
--# define YY_STACK_PRINT(Bottom, Top) \
--do { \
-- if (yydebug) \
-- yy_stack_print ((Bottom), (Top)); \
--} while (YYID (0))
-+# define YY_STACK_PRINT(Bottom, Top) \
-+do { \
-+ if (yydebug) \
-+ yy_stack_print ((Bottom), (Top)); \
-+} while (0)
-
-
- /*------------------------------------------------.
- | Report that the YYRULE is going to be reduced. |
- `------------------------------------------------*/
-
--#if (defined __STDC__ || defined __C99__FUNC__ \
-- || defined __cplusplus || defined _MSC_VER)
--static void
--yy_reduce_print (YYSTYPE *yyvsp, YYLTYPE *yylsp, int yyrule)
--#else
- static void
--yy_reduce_print (yyvsp, yylsp, yyrule)
-- YYSTYPE *yyvsp;
-- YYLTYPE *yylsp;
-- int yyrule;
--#endif
-+yy_reduce_print (yytype_int16 *yyssp, YYSTYPE *yyvsp, YYLTYPE *yylsp, int yyrule)
- {
-+ unsigned long int yylno = yyrline[yyrule];
- int yynrhs = yyr2[yyrule];
- int yyi;
-- unsigned long int yylno = yyrline[yyrule];
- YYFPRINTF (stderr, "Reducing stack by rule %d (line %lu):\n",
-- yyrule - 1, yylno);
-+ yyrule - 1, yylno);
- /* The symbols being reduced. */
- for (yyi = 0; yyi < yynrhs; yyi++)
- {
- YYFPRINTF (stderr, " $%d = ", yyi + 1);
-- yy_symbol_print (stderr, yyrhs[yyprhs[yyrule] + yyi],
-- &(yyvsp[(yyi + 1) - (yynrhs)])
-- , &(yylsp[(yyi + 1) - (yynrhs)]) );
-+ yy_symbol_print (stderr,
-+ yystos[yyssp[yyi + 1 - yynrhs]],
-+ &(yyvsp[(yyi + 1) - (yynrhs)])
-+ , &(yylsp[(yyi + 1) - (yynrhs)]) );
- YYFPRINTF (stderr, "\n");
- }
- }
-
--# define YY_REDUCE_PRINT(Rule) \
--do { \
-- if (yydebug) \
-- yy_reduce_print (yyvsp, yylsp, Rule); \
--} while (YYID (0))
-+# define YY_REDUCE_PRINT(Rule) \
-+do { \
-+ if (yydebug) \
-+ yy_reduce_print (yyssp, yyvsp, yylsp, Rule); \
-+} while (0)
-
- /* Nonzero means print parse trace. It is left uninitialized so that
- multiple parsers can coexist. */
-@@ -988,7 +931,7 @@ int yydebug;
-
-
- /* YYINITDEPTH -- initial size of the parser's stacks. */
--#ifndef YYINITDEPTH
-+#ifndef YYINITDEPTH
- # define YYINITDEPTH 200
- #endif
-
-@@ -1011,15 +954,8 @@ int yydebug;
- # define yystrlen strlen
- # else
- /* Return the length of YYSTR. */
--#if (defined __STDC__ || defined __C99__FUNC__ \
-- || defined __cplusplus || defined _MSC_VER)
- static YYSIZE_T
- yystrlen (const char *yystr)
--#else
--static YYSIZE_T
--yystrlen (yystr)
-- const char *yystr;
--#endif
- {
- YYSIZE_T yylen;
- for (yylen = 0; yystr[yylen]; yylen++)
-@@ -1035,16 +971,8 @@ yystrlen (yystr)
- # else
- /* Copy YYSRC to YYDEST, returning the address of the terminating '\0' in
- YYDEST. */
--#if (defined __STDC__ || defined __C99__FUNC__ \
-- || defined __cplusplus || defined _MSC_VER)
- static char *
- yystpcpy (char *yydest, const char *yysrc)
--#else
--static char *
--yystpcpy (yydest, yysrc)
-- char *yydest;
-- const char *yysrc;
--#endif
- {
- char *yyd = yydest;
- const char *yys = yysrc;
-@@ -1074,27 +1002,27 @@ yytnamerr (char *yyres, const char *yyst
- char const *yyp = yystr;
-
- for (;;)
-- switch (*++yyp)
-- {
-- case '\'':
-- case ',':
-- goto do_not_strip_quotes;
--
-- case '\\':
-- if (*++yyp != '\\')
-- goto do_not_strip_quotes;
-- /* Fall through. */
-- default:
-- if (yyres)
-- yyres[yyn] = *yyp;
-- yyn++;
-- break;
--
-- case '"':
-- if (yyres)
-- yyres[yyn] = '\0';
-- return yyn;
-- }
-+ switch (*++yyp)
-+ {
-+ case '\'':
-+ case ',':
-+ goto do_not_strip_quotes;
-+
-+ case '\\':
-+ if (*++yyp != '\\')
-+ goto do_not_strip_quotes;
-+ /* Fall through. */
-+ default:
-+ if (yyres)
-+ yyres[yyn] = *yyp;
-+ yyn++;
-+ break;
-+
-+ case '"':
-+ if (yyres)
-+ yyres[yyn] = '\0';
-+ return yyn;
-+ }
- do_not_strip_quotes: ;
- }
-
-@@ -1117,12 +1045,11 @@ static int
- yysyntax_error (YYSIZE_T *yymsg_alloc, char **yymsg,
- yytype_int16 *yyssp, int yytoken)
- {
-- YYSIZE_T yysize0 = yytnamerr (0, yytname[yytoken]);
-+ YYSIZE_T yysize0 = yytnamerr (YY_NULLPTR, yytname[yytoken]);
- YYSIZE_T yysize = yysize0;
-- YYSIZE_T yysize1;
- enum { YYERROR_VERBOSE_ARGS_MAXIMUM = 5 };
- /* Internationalized format string. */
-- const char *yyformat = 0;
-+ const char *yyformat = YY_NULLPTR;
- /* Arguments of yyformat. */
- char const *yyarg[YYERROR_VERBOSE_ARGS_MAXIMUM];
- /* Number of reported tokens (one for the "unexpected", one per
-@@ -1130,10 +1057,6 @@ yysyntax_error (YYSIZE_T *yymsg_alloc, c
- int yycount = 0;
-
- /* There are many possibilities here to consider:
-- - Assume YYFAIL is not used. It's too flawed to consider. See
-- <http://lists.gnu.org/archive/html/bison-patches/2009-12/msg00024.html>
-- for details. YYERROR is fine as it does not invoke this
-- function.
- - If this state is a consistent state with a default action, then
- the only way this function was invoked is if the default action
- is an error action. In that case, don't check for expected
-@@ -1182,11 +1105,13 @@ yysyntax_error (YYSIZE_T *yymsg_alloc, c
- break;
- }
- yyarg[yycount++] = yytname[yyx];
-- yysize1 = yysize + yytnamerr (0, yytname[yyx]);
-- if (! (yysize <= yysize1
-- && yysize1 <= YYSTACK_ALLOC_MAXIMUM))
-- return 2;
-- yysize = yysize1;
-+ {
-+ YYSIZE_T yysize1 = yysize + yytnamerr (YY_NULLPTR, yytname[yyx]);
-+ if (! (yysize <= yysize1
-+ && yysize1 <= YYSTACK_ALLOC_MAXIMUM))
-+ return 2;
-+ yysize = yysize1;
-+ }
- }
- }
- }
-@@ -1206,10 +1131,12 @@ yysyntax_error (YYSIZE_T *yymsg_alloc, c
- # undef YYCASE_
- }
-
-- yysize1 = yysize + yystrlen (yyformat);
-- if (! (yysize <= yysize1 && yysize1 <= YYSTACK_ALLOC_MAXIMUM))
-- return 2;
-- yysize = yysize1;
-+ {
-+ YYSIZE_T yysize1 = yysize + yystrlen (yyformat);
-+ if (! (yysize <= yysize1 && yysize1 <= YYSTACK_ALLOC_MAXIMUM))
-+ return 2;
-+ yysize = yysize1;
-+ }
-
- if (*yymsg_alloc < yysize)
- {
-@@ -1246,50 +1173,21 @@ yysyntax_error (YYSIZE_T *yymsg_alloc, c
- | Release the memory associated to this symbol. |
- `-----------------------------------------------*/
-
--/*ARGSUSED*/
--#if (defined __STDC__ || defined __C99__FUNC__ \
-- || defined __cplusplus || defined _MSC_VER)
- static void
- yydestruct (const char *yymsg, int yytype, YYSTYPE *yyvaluep, YYLTYPE *yylocationp)
--#else
--static void
--yydestruct (yymsg, yytype, yyvaluep, yylocationp)
-- const char *yymsg;
-- int yytype;
-- YYSTYPE *yyvaluep;
-- YYLTYPE *yylocationp;
--#endif
- {
- YYUSE (yyvaluep);
- YYUSE (yylocationp);
--
- if (!yymsg)
- yymsg = "Deleting";
- YY_SYMBOL_PRINT (yymsg, yytype, yyvaluep, yylocationp);
-
-- switch (yytype)
-- {
--
-- default:
-- break;
-- }
-+ YY_IGNORE_MAYBE_UNINITIALIZED_BEGIN
-+ YYUSE (yytype);
-+ YY_IGNORE_MAYBE_UNINITIALIZED_END
- }
-
-
--/* Prevent warnings from -Wmissing-prototypes. */
--#ifdef YYPARSE_PARAM
--#if defined __STDC__ || defined __cplusplus
--int yyparse (void *YYPARSE_PARAM);
--#else
--int yyparse ();
--#endif
--#else /* ! YYPARSE_PARAM */
--#if defined __STDC__ || defined __cplusplus
--int yyparse (void);
--#else
--int yyparse ();
--#endif
--#endif /* ! YYPARSE_PARAM */
-
-
- /* The lookahead symbol. */
-@@ -1297,10 +1195,12 @@ int yychar;
-
- /* The semantic value of the lookahead symbol. */
- YYSTYPE yylval;
--
- /* Location data for the lookahead symbol. */
--YYLTYPE yylloc;
--
-+YYLTYPE yylloc
-+# if defined YYLTYPE_IS_TRIVIAL && YYLTYPE_IS_TRIVIAL
-+ = { 1, 1, 1, 1 }
-+# endif
-+;
- /* Number of syntax errors so far. */
- int yynerrs;
-
-@@ -1309,38 +1209,19 @@ int yynerrs;
- | yyparse. |
- `----------*/
-
--#ifdef YYPARSE_PARAM
--#if (defined __STDC__ || defined __C99__FUNC__ \
-- || defined __cplusplus || defined _MSC_VER)
--int
--yyparse (void *YYPARSE_PARAM)
--#else
--int
--yyparse (YYPARSE_PARAM)
-- void *YYPARSE_PARAM;
--#endif
--#else /* ! YYPARSE_PARAM */
--#if (defined __STDC__ || defined __C99__FUNC__ \
-- || defined __cplusplus || defined _MSC_VER)
- int
- yyparse (void)
--#else
--int
--yyparse ()
--
--#endif
--#endif
- {
- int yystate;
- /* Number of tokens to shift before error messages enabled. */
- int yyerrstatus;
-
- /* The stacks and their tools:
-- `yyss': related to states.
-- `yyvs': related to semantic values.
-- `yyls': related to locations.
-+ 'yyss': related to states.
-+ 'yyvs': related to semantic values.
-+ 'yyls': related to locations.
-
-- Refer to the stacks thru separate pointers, to allow yyoverflow
-+ Refer to the stacks through separate pointers, to allow yyoverflow
- to reallocate them elsewhere. */
-
- /* The state stack. */
-@@ -1366,7 +1247,7 @@ yyparse ()
- int yyn;
- int yyresult;
- /* Lookahead token as an internal (translated) token number. */
-- int yytoken;
-+ int yytoken = 0;
- /* The variables used to return semantic value and location from the
- action routines. */
- YYSTYPE yyval;
-@@ -1385,10 +1266,9 @@ yyparse ()
- Keep to zero when no symbol should be popped. */
- int yylen = 0;
-
-- yytoken = 0;
-- yyss = yyssa;
-- yyvs = yyvsa;
-- yyls = yylsa;
-+ yyssp = yyss = yyssa;
-+ yyvsp = yyvs = yyvsa;
-+ yylsp = yyls = yylsa;
- yystacksize = YYINITDEPTH;
-
- YYDPRINTF ((stderr, "Starting parse\n"));
-@@ -1397,21 +1277,7 @@ yyparse ()
- yyerrstatus = 0;
- yynerrs = 0;
- yychar = YYEMPTY; /* Cause a token to be read. */
--
-- /* Initialize stack pointers.
-- Waste one element of value and location stack
-- so that they stay on the same level as the state stack.
-- The wasted elements are never initialized. */
-- yyssp = yyss;
-- yyvsp = yyvs;
-- yylsp = yyls;
--
--#if defined YYLTYPE_IS_TRIVIAL && YYLTYPE_IS_TRIVIAL
-- /* Initialize the default location before parsing starts. */
-- yylloc.first_line = yylloc.last_line = 1;
-- yylloc.first_column = yylloc.last_column = 1;
--#endif
--
-+ yylsp[0] = yylloc;
- goto yysetstate;
-
- /*------------------------------------------------------------.
-@@ -1432,26 +1298,26 @@ yyparse ()
-
- #ifdef yyoverflow
- {
-- /* Give user a chance to reallocate the stack. Use copies of
-- these so that the &'s don't force the real ones into
-- memory. */
-- YYSTYPE *yyvs1 = yyvs;
-- yytype_int16 *yyss1 = yyss;
-- YYLTYPE *yyls1 = yyls;
--
-- /* Each stack pointer address is followed by the size of the
-- data in use in that stack, in bytes. This used to be a
-- conditional around just the two extra args, but that might
-- be undefined if yyoverflow is a macro. */
-- yyoverflow (YY_("memory exhausted"),
-- &yyss1, yysize * sizeof (*yyssp),
-- &yyvs1, yysize * sizeof (*yyvsp),
-- &yyls1, yysize * sizeof (*yylsp),
-- &yystacksize);
--
-- yyls = yyls1;
-- yyss = yyss1;
-- yyvs = yyvs1;
-+ /* Give user a chance to reallocate the stack. Use copies of
-+ these so that the &'s don't force the real ones into
-+ memory. */
-+ YYSTYPE *yyvs1 = yyvs;
-+ yytype_int16 *yyss1 = yyss;
-+ YYLTYPE *yyls1 = yyls;
-+
-+ /* Each stack pointer address is followed by the size of the
-+ data in use in that stack, in bytes. This used to be a
-+ conditional around just the two extra args, but that might
-+ be undefined if yyoverflow is a macro. */
-+ yyoverflow (YY_("memory exhausted"),
-+ &yyss1, yysize * sizeof (*yyssp),
-+ &yyvs1, yysize * sizeof (*yyvsp),
-+ &yyls1, yysize * sizeof (*yylsp),
-+ &yystacksize);
-+
-+ yyls = yyls1;
-+ yyss = yyss1;
-+ yyvs = yyvs1;
- }
- #else /* no yyoverflow */
- # ifndef YYSTACK_RELOCATE
-@@ -1459,23 +1325,23 @@ yyparse ()
- # else
- /* Extend the stack our own way. */
- if (YYMAXDEPTH <= yystacksize)
-- goto yyexhaustedlab;
-+ goto yyexhaustedlab;
- yystacksize *= 2;
- if (YYMAXDEPTH < yystacksize)
-- yystacksize = YYMAXDEPTH;
-+ yystacksize = YYMAXDEPTH;
-
- {
-- yytype_int16 *yyss1 = yyss;
-- union yyalloc *yyptr =
-- (union yyalloc *) YYSTACK_ALLOC (YYSTACK_BYTES (yystacksize));
-- if (! yyptr)
-- goto yyexhaustedlab;
-- YYSTACK_RELOCATE (yyss_alloc, yyss);
-- YYSTACK_RELOCATE (yyvs_alloc, yyvs);
-- YYSTACK_RELOCATE (yyls_alloc, yyls);
-+ yytype_int16 *yyss1 = yyss;
-+ union yyalloc *yyptr =
-+ (union yyalloc *) YYSTACK_ALLOC (YYSTACK_BYTES (yystacksize));
-+ if (! yyptr)
-+ goto yyexhaustedlab;
-+ YYSTACK_RELOCATE (yyss_alloc, yyss);
-+ YYSTACK_RELOCATE (yyvs_alloc, yyvs);
-+ YYSTACK_RELOCATE (yyls_alloc, yyls);
- # undef YYSTACK_RELOCATE
-- if (yyss1 != yyssa)
-- YYSTACK_FREE (yyss1);
-+ if (yyss1 != yyssa)
-+ YYSTACK_FREE (yyss1);
- }
- # endif
- #endif /* no yyoverflow */
-@@ -1485,10 +1351,10 @@ yyparse ()
- yylsp = yyls + yysize - 1;
-
- YYDPRINTF ((stderr, "Stack size increased to %lu\n",
-- (unsigned long int) yystacksize));
-+ (unsigned long int) yystacksize));
-
- if (yyss + yystacksize - 1 <= yyssp)
-- YYABORT;
-+ YYABORT;
- }
-
- YYDPRINTF ((stderr, "Entering state %d\n", yystate));
-@@ -1517,7 +1383,7 @@ yybackup:
- if (yychar == YYEMPTY)
- {
- YYDPRINTF ((stderr, "Reading a token: "));
-- yychar = YYLEX;
-+ yychar = yylex ();
- }
-
- if (yychar <= YYEOF)
-@@ -1557,7 +1423,9 @@ yybackup:
- yychar = YYEMPTY;
-
- yystate = yyn;
-+ YY_IGNORE_MAYBE_UNINITIALIZED_BEGIN
- *++yyvsp = yylval;
-+ YY_IGNORE_MAYBE_UNINITIALIZED_END
- *++yylsp = yylloc;
- goto yynewstate;
-
-@@ -1580,7 +1448,7 @@ yyreduce:
- yylen = yyr2[yyn];
-
- /* If YYLEN is nonzero, implement the default value of the action:
-- `$$ = $1'.
-+ '$$ = $1'.
-
- Otherwise, the following line sets YYVAL to garbage.
- This behavior is undocumented and Bison
-@@ -1595,322 +1463,273 @@ yyreduce:
- switch (yyn)
- {
- case 2:
--
--/* Line 1806 of yacc.c */
--#line 109 "dtc-parser.y"
-+#line 105 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyvsp[(5) - (5)].node)->is_plugin = (yyvsp[(3) - (5)].is_plugin);
-- (yyvsp[(5) - (5)].node)->is_root = 1;
-- the_boot_info = build_boot_info((yyvsp[(4) - (5)].re), (yyvsp[(5) - (5)].node),
-- guess_boot_cpuid((yyvsp[(5) - (5)].node)));
-+ the_boot_info = build_boot_info((yyvsp[-1].re), (yyvsp[0].node),
-+ guess_boot_cpuid((yyvsp[0].node)));
- }
-+#line 1472 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 3:
--
--/* Line 1806 of yacc.c */
--#line 119 "dtc-parser.y"
-+#line 113 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.is_plugin) = 0;
-+ (yyval.re) = NULL;
- }
-+#line 1480 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 4:
--
--/* Line 1806 of yacc.c */
--#line 123 "dtc-parser.y"
-+#line 117 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.is_plugin) = 1;
-+ (yyval.re) = chain_reserve_entry((yyvsp[-1].re), (yyvsp[0].re));
- }
-+#line 1488 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 5:
--
--/* Line 1806 of yacc.c */
--#line 130 "dtc-parser.y"
-+#line 124 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.re) = NULL;
-+ (yyval.re) = build_reserve_entry((yyvsp[-2].integer), (yyvsp[-1].integer));
- }
-+#line 1496 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 6:
--
--/* Line 1806 of yacc.c */
--#line 134 "dtc-parser.y"
-+#line 128 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.re) = chain_reserve_entry((yyvsp[(1) - (2)].re), (yyvsp[(2) - (2)].re));
-+ add_label(&(yyvsp[0].re)->labels, (yyvsp[-1].labelref));
-+ (yyval.re) = (yyvsp[0].re);
- }
-+#line 1505 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 7:
--
--/* Line 1806 of yacc.c */
--#line 141 "dtc-parser.y"
-+#line 136 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.re) = build_reserve_entry((yyvsp[(2) - (4)].integer), (yyvsp[(3) - (4)].integer));
-+ (yyval.node) = name_node((yyvsp[0].node), "");
- }
-+#line 1513 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 8:
--
--/* Line 1806 of yacc.c */
--#line 145 "dtc-parser.y"
-+#line 140 "dtc-parser.y" /* yacc.c:1646 */
- {
-- add_label(&(yyvsp[(2) - (2)].re)->labels, (yyvsp[(1) - (2)].labelref));
-- (yyval.re) = (yyvsp[(2) - (2)].re);
-+ (yyval.node) = merge_nodes((yyvsp[-2].node), (yyvsp[0].node));
- }
-+#line 1521 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 9:
--
--/* Line 1806 of yacc.c */
--#line 153 "dtc-parser.y"
-+#line 145 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.node) = name_node((yyvsp[(2) - (2)].node), "");
-+ struct node *target = get_node_by_ref((yyvsp[-3].node), (yyvsp[-1].labelref));
-+
-+ add_label(&target->labels, (yyvsp[-2].labelref));
-+ if (target)
-+ merge_nodes(target, (yyvsp[0].node));
-+ else
-+ ERROR(&(yylsp[-1]), "Label or path %s not found", (yyvsp[-1].labelref));
-+ (yyval.node) = (yyvsp[-3].node);
- }
-+#line 1536 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 10:
--
--/* Line 1806 of yacc.c */
--#line 157 "dtc-parser.y"
-+#line 156 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.node) = merge_nodes((yyvsp[(1) - (3)].node), (yyvsp[(3) - (3)].node));
-+ struct node *target = get_node_by_ref((yyvsp[-2].node), (yyvsp[-1].labelref));
-+
-+ if (target)
-+ merge_nodes(target, (yyvsp[0].node));
-+ else
-+ ERROR(&(yylsp[-1]), "Label or path %s not found", (yyvsp[-1].labelref));
-+ (yyval.node) = (yyvsp[-2].node);
- }
-+#line 1550 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 11:
--
--/* Line 1806 of yacc.c */
--#line 162 "dtc-parser.y"
-+#line 166 "dtc-parser.y" /* yacc.c:1646 */
- {
-- struct node *target = get_node_by_ref((yyvsp[(1) - (4)].node), (yyvsp[(3) - (4)].labelref));
-+ struct node *target = get_node_by_ref((yyvsp[-3].node), (yyvsp[-1].labelref));
-
-- add_label(&target->labels, (yyvsp[(2) - (4)].labelref));
- if (target)
-- merge_nodes(target, (yyvsp[(4) - (4)].node));
-+ delete_node(target);
- else
-- ERROR(&(yylsp[(3) - (4)]), "Label or path %s not found", (yyvsp[(3) - (4)].labelref));
-- (yyval.node) = (yyvsp[(1) - (4)].node);
-+ ERROR(&(yylsp[-1]), "Label or path %s not found", (yyvsp[-1].labelref));
-+
-+
-+ (yyval.node) = (yyvsp[-3].node);
- }
-+#line 1566 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 12:
--
--/* Line 1806 of yacc.c */
--#line 173 "dtc-parser.y"
-+#line 181 "dtc-parser.y" /* yacc.c:1646 */
- {
-- struct node *target = get_node_by_ref((yyvsp[(1) - (3)].node), (yyvsp[(2) - (3)].labelref));
--
-- if (target)
-- merge_nodes(target, (yyvsp[(3) - (3)].node));
-- else
-- ERROR(&(yylsp[(2) - (3)]), "Label or path %s not found", (yyvsp[(2) - (3)].labelref));
-- (yyval.node) = (yyvsp[(1) - (3)].node);
-+ (yyval.node) = build_node((yyvsp[-3].proplist), (yyvsp[-2].nodelist));
- }
-+#line 1574 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 13:
--
--/* Line 1806 of yacc.c */
--#line 183 "dtc-parser.y"
-+#line 188 "dtc-parser.y" /* yacc.c:1646 */
- {
-- struct node *target = get_node_by_ref((yyvsp[(1) - (4)].node), (yyvsp[(3) - (4)].labelref));
--
-- if (target)
-- delete_node(target);
-- else
-- ERROR(&(yylsp[(3) - (4)]), "Label or path %s not found", (yyvsp[(3) - (4)].labelref));
--
--
-- (yyval.node) = (yyvsp[(1) - (4)].node);
-+ (yyval.proplist) = NULL;
- }
-+#line 1582 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 14:
--
--/* Line 1806 of yacc.c */
--#line 198 "dtc-parser.y"
-+#line 192 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.node) = build_node((yyvsp[(2) - (5)].proplist), (yyvsp[(3) - (5)].nodelist));
-+ (yyval.proplist) = chain_property((yyvsp[0].prop), (yyvsp[-1].proplist));
- }
-+#line 1590 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 15:
--
--/* Line 1806 of yacc.c */
--#line 205 "dtc-parser.y"
-+#line 199 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.proplist) = NULL;
-+ (yyval.prop) = build_property((yyvsp[-3].propnodename), (yyvsp[-1].data));
- }
-+#line 1598 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 16:
--
--/* Line 1806 of yacc.c */
--#line 209 "dtc-parser.y"
-+#line 203 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.proplist) = chain_property((yyvsp[(2) - (2)].prop), (yyvsp[(1) - (2)].proplist));
-+ (yyval.prop) = build_property((yyvsp[-1].propnodename), empty_data);
- }
-+#line 1606 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 17:
--
--/* Line 1806 of yacc.c */
--#line 216 "dtc-parser.y"
-+#line 207 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.prop) = build_property((yyvsp[(1) - (4)].propnodename), (yyvsp[(3) - (4)].data));
-+ (yyval.prop) = build_property_delete((yyvsp[-1].propnodename));
- }
-+#line 1614 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 18:
--
--/* Line 1806 of yacc.c */
--#line 220 "dtc-parser.y"
-+#line 211 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.prop) = build_property((yyvsp[(1) - (2)].propnodename), empty_data);
-+ add_label(&(yyvsp[0].prop)->labels, (yyvsp[-1].labelref));
-+ (yyval.prop) = (yyvsp[0].prop);
- }
-+#line 1623 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 19:
--
--/* Line 1806 of yacc.c */
--#line 224 "dtc-parser.y"
-+#line 219 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.prop) = build_property_delete((yyvsp[(2) - (3)].propnodename));
-+ (yyval.data) = data_merge((yyvsp[-1].data), (yyvsp[0].data));
- }
-+#line 1631 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 20:
--
--/* Line 1806 of yacc.c */
--#line 228 "dtc-parser.y"
-+#line 223 "dtc-parser.y" /* yacc.c:1646 */
- {
-- add_label(&(yyvsp[(2) - (2)].prop)->labels, (yyvsp[(1) - (2)].labelref));
-- (yyval.prop) = (yyvsp[(2) - (2)].prop);
-+ (yyval.data) = data_merge((yyvsp[-2].data), (yyvsp[-1].array).data);
- }
-+#line 1639 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 21:
--
--/* Line 1806 of yacc.c */
--#line 236 "dtc-parser.y"
-+#line 227 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.data) = data_merge((yyvsp[(1) - (2)].data), (yyvsp[(2) - (2)].data));
-+ (yyval.data) = data_merge((yyvsp[-3].data), (yyvsp[-1].data));
- }
-+#line 1647 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 22:
--
--/* Line 1806 of yacc.c */
--#line 240 "dtc-parser.y"
-+#line 231 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.data) = data_merge((yyvsp[(1) - (3)].data), (yyvsp[(2) - (3)].array).data);
-+ (yyval.data) = data_add_marker((yyvsp[-1].data), REF_PATH, (yyvsp[0].labelref));
- }
-+#line 1655 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 23:
--
--/* Line 1806 of yacc.c */
--#line 244 "dtc-parser.y"
-- {
-- (yyval.data) = data_merge((yyvsp[(1) - (4)].data), (yyvsp[(3) - (4)].data));
-- }
-- break;
--
-- case 24:
--
--/* Line 1806 of yacc.c */
--#line 248 "dtc-parser.y"
-- {
-- (yyval.data) = data_add_marker((yyvsp[(1) - (2)].data), REF_PATH, (yyvsp[(2) - (2)].labelref));
-- }
-- break;
--
-- case 25:
--
--/* Line 1806 of yacc.c */
--#line 252 "dtc-parser.y"
-+#line 235 "dtc-parser.y" /* yacc.c:1646 */
- {
-- FILE *f = srcfile_relative_open((yyvsp[(4) - (9)].data).val, NULL);
-+ FILE *f = srcfile_relative_open((yyvsp[-5].data).val, NULL);
- struct data d;
-
-- if ((yyvsp[(6) - (9)].integer) != 0)
-- if (fseek(f, (yyvsp[(6) - (9)].integer), SEEK_SET) != 0)
-+ if ((yyvsp[-3].integer) != 0)
-+ if (fseek(f, (yyvsp[-3].integer), SEEK_SET) != 0)
- die("Couldn't seek to offset %llu in \"%s\": %s",
-- (unsigned long long)(yyvsp[(6) - (9)].integer), (yyvsp[(4) - (9)].data).val,
-+ (unsigned long long)(yyvsp[-3].integer), (yyvsp[-5].data).val,
- strerror(errno));
-
-- d = data_copy_file(f, (yyvsp[(8) - (9)].integer));
-+ d = data_copy_file(f, (yyvsp[-1].integer));
-
-- (yyval.data) = data_merge((yyvsp[(1) - (9)].data), d);
-+ (yyval.data) = data_merge((yyvsp[-8].data), d);
- fclose(f);
- }
-+#line 1675 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 26:
--
--/* Line 1806 of yacc.c */
--#line 268 "dtc-parser.y"
-+ case 24:
-+#line 251 "dtc-parser.y" /* yacc.c:1646 */
- {
-- FILE *f = srcfile_relative_open((yyvsp[(4) - (5)].data).val, NULL);
-+ FILE *f = srcfile_relative_open((yyvsp[-1].data).val, NULL);
- struct data d = empty_data;
-
- d = data_copy_file(f, -1);
-
-- (yyval.data) = data_merge((yyvsp[(1) - (5)].data), d);
-+ (yyval.data) = data_merge((yyvsp[-4].data), d);
- fclose(f);
- }
-+#line 1689 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 27:
--
--/* Line 1806 of yacc.c */
--#line 278 "dtc-parser.y"
-+ case 25:
-+#line 261 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.data) = data_add_marker((yyvsp[(1) - (2)].data), LABEL, (yyvsp[(2) - (2)].labelref));
-+ (yyval.data) = data_add_marker((yyvsp[-1].data), LABEL, (yyvsp[0].labelref));
- }
-+#line 1697 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 28:
--
--/* Line 1806 of yacc.c */
--#line 285 "dtc-parser.y"
-+ case 26:
-+#line 268 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.data) = empty_data;
- }
-+#line 1705 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 29:
--
--/* Line 1806 of yacc.c */
--#line 289 "dtc-parser.y"
-+ case 27:
-+#line 272 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.data) = (yyvsp[(1) - (2)].data);
-+ (yyval.data) = (yyvsp[-1].data);
- }
-+#line 1713 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 30:
--
--/* Line 1806 of yacc.c */
--#line 293 "dtc-parser.y"
-+ case 28:
-+#line 276 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.data) = data_add_marker((yyvsp[(1) - (2)].data), LABEL, (yyvsp[(2) - (2)].labelref));
-+ (yyval.data) = data_add_marker((yyvsp[-1].data), LABEL, (yyvsp[0].labelref));
- }
-+#line 1721 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 31:
--
--/* Line 1806 of yacc.c */
--#line 300 "dtc-parser.y"
-+ case 29:
-+#line 283 "dtc-parser.y" /* yacc.c:1646 */
- {
- unsigned long long bits;
-
-- bits = (yyvsp[(2) - (3)].integer);
-+ bits = (yyvsp[-1].integer);
-
- if ((bits != 8) && (bits != 16) &&
- (bits != 32) && (bits != 64)) {
-- ERROR(&(yylsp[(2) - (3)]), "Array elements must be"
-+ ERROR(&(yylsp[-1]), "Array elements must be"
- " 8, 16, 32 or 64-bits");
- bits = 32;
- }
-@@ -1918,25 +1737,23 @@ yyreduce:
- (yyval.array).data = empty_data;
- (yyval.array).bits = bits;
- }
-+#line 1741 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 32:
--
--/* Line 1806 of yacc.c */
--#line 316 "dtc-parser.y"
-+ case 30:
-+#line 299 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.array).data = empty_data;
- (yyval.array).bits = 32;
- }
-+#line 1750 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 33:
--
--/* Line 1806 of yacc.c */
--#line 321 "dtc-parser.y"
-+ case 31:
-+#line 304 "dtc-parser.y" /* yacc.c:1646 */
- {
-- if ((yyvsp[(1) - (2)].array).bits < 64) {
-- uint64_t mask = (1ULL << (yyvsp[(1) - (2)].array).bits) - 1;
-+ if ((yyvsp[-1].array).bits < 64) {
-+ uint64_t mask = (1ULL << (yyvsp[-1].array).bits) - 1;
- /*
- * Bits above mask must either be all zero
- * (positive within range of mask) or all one
-@@ -1945,293 +1762,258 @@ yyreduce:
- * within the mask to one (i.e. | in the
- * mask), all bits are one.
- */
-- if (((yyvsp[(2) - (2)].integer) > mask) && (((yyvsp[(2) - (2)].integer) | mask) != -1ULL))
-- ERROR(&(yylsp[(2) - (2)]), "Value out of range for"
-- " %d-bit array element", (yyvsp[(1) - (2)].array).bits);
-+ if (((yyvsp[0].integer) > mask) && (((yyvsp[0].integer) | mask) != -1ULL))
-+ ERROR(&(yylsp[0]), "Value out of range for"
-+ " %d-bit array element", (yyvsp[-1].array).bits);
- }
-
-- (yyval.array).data = data_append_integer((yyvsp[(1) - (2)].array).data, (yyvsp[(2) - (2)].integer), (yyvsp[(1) - (2)].array).bits);
-+ (yyval.array).data = data_append_integer((yyvsp[-1].array).data, (yyvsp[0].integer), (yyvsp[-1].array).bits);
- }
-+#line 1773 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 34:
--
--/* Line 1806 of yacc.c */
--#line 340 "dtc-parser.y"
-+ case 32:
-+#line 323 "dtc-parser.y" /* yacc.c:1646 */
- {
-- uint64_t val = ~0ULL >> (64 - (yyvsp[(1) - (2)].array).bits);
-+ uint64_t val = ~0ULL >> (64 - (yyvsp[-1].array).bits);
-
-- if ((yyvsp[(1) - (2)].array).bits == 32)
-- (yyvsp[(1) - (2)].array).data = data_add_marker((yyvsp[(1) - (2)].array).data,
-+ if ((yyvsp[-1].array).bits == 32)
-+ (yyvsp[-1].array).data = data_add_marker((yyvsp[-1].array).data,
- REF_PHANDLE,
-- (yyvsp[(2) - (2)].labelref));
-+ (yyvsp[0].labelref));
- else
-- ERROR(&(yylsp[(2) - (2)]), "References are only allowed in "
-+ ERROR(&(yylsp[0]), "References are only allowed in "
- "arrays with 32-bit elements.");
-
-- (yyval.array).data = data_append_integer((yyvsp[(1) - (2)].array).data, val, (yyvsp[(1) - (2)].array).bits);
-+ (yyval.array).data = data_append_integer((yyvsp[-1].array).data, val, (yyvsp[-1].array).bits);
- }
-+#line 1791 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 35:
--
--/* Line 1806 of yacc.c */
--#line 354 "dtc-parser.y"
-+ case 33:
-+#line 337 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.array).data = data_add_marker((yyvsp[(1) - (2)].array).data, LABEL, (yyvsp[(2) - (2)].labelref));
-+ (yyval.array).data = data_add_marker((yyvsp[-1].array).data, LABEL, (yyvsp[0].labelref));
- }
-+#line 1799 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 38:
--
--/* Line 1806 of yacc.c */
--#line 363 "dtc-parser.y"
-+ case 36:
-+#line 346 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.integer) = (yyvsp[(2) - (3)].integer);
-+ (yyval.integer) = (yyvsp[-1].integer);
- }
-+#line 1807 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 41:
-+ case 39:
-+#line 357 "dtc-parser.y" /* yacc.c:1646 */
-+ { (yyval.integer) = (yyvsp[-4].integer) ? (yyvsp[-2].integer) : (yyvsp[0].integer); }
-+#line 1813 "dtc-parser.tab.c" /* yacc.c:1646 */
-+ break;
-
--/* Line 1806 of yacc.c */
--#line 374 "dtc-parser.y"
-- { (yyval.integer) = (yyvsp[(1) - (5)].integer) ? (yyvsp[(3) - (5)].integer) : (yyvsp[(5) - (5)].integer); }
-+ case 41:
-+#line 362 "dtc-parser.y" /* yacc.c:1646 */
-+ { (yyval.integer) = (yyvsp[-2].integer) || (yyvsp[0].integer); }
-+#line 1819 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 43:
--
--/* Line 1806 of yacc.c */
--#line 379 "dtc-parser.y"
-- { (yyval.integer) = (yyvsp[(1) - (3)].integer) || (yyvsp[(3) - (3)].integer); }
-+#line 367 "dtc-parser.y" /* yacc.c:1646 */
-+ { (yyval.integer) = (yyvsp[-2].integer) && (yyvsp[0].integer); }
-+#line 1825 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 45:
--
--/* Line 1806 of yacc.c */
--#line 384 "dtc-parser.y"
-- { (yyval.integer) = (yyvsp[(1) - (3)].integer) && (yyvsp[(3) - (3)].integer); }
-+#line 372 "dtc-parser.y" /* yacc.c:1646 */
-+ { (yyval.integer) = (yyvsp[-2].integer) | (yyvsp[0].integer); }
-+#line 1831 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 47:
--
--/* Line 1806 of yacc.c */
--#line 389 "dtc-parser.y"
-- { (yyval.integer) = (yyvsp[(1) - (3)].integer) | (yyvsp[(3) - (3)].integer); }
-+#line 377 "dtc-parser.y" /* yacc.c:1646 */
-+ { (yyval.integer) = (yyvsp[-2].integer) ^ (yyvsp[0].integer); }
-+#line 1837 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 49:
--
--/* Line 1806 of yacc.c */
--#line 394 "dtc-parser.y"
-- { (yyval.integer) = (yyvsp[(1) - (3)].integer) ^ (yyvsp[(3) - (3)].integer); }
-+#line 382 "dtc-parser.y" /* yacc.c:1646 */
-+ { (yyval.integer) = (yyvsp[-2].integer) & (yyvsp[0].integer); }
-+#line 1843 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 51:
--
--/* Line 1806 of yacc.c */
--#line 399 "dtc-parser.y"
-- { (yyval.integer) = (yyvsp[(1) - (3)].integer) & (yyvsp[(3) - (3)].integer); }
-+#line 387 "dtc-parser.y" /* yacc.c:1646 */
-+ { (yyval.integer) = (yyvsp[-2].integer) == (yyvsp[0].integer); }
-+#line 1849 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 53:
--
--/* Line 1806 of yacc.c */
--#line 404 "dtc-parser.y"
-- { (yyval.integer) = (yyvsp[(1) - (3)].integer) == (yyvsp[(3) - (3)].integer); }
-+ case 52:
-+#line 388 "dtc-parser.y" /* yacc.c:1646 */
-+ { (yyval.integer) = (yyvsp[-2].integer) != (yyvsp[0].integer); }
-+#line 1855 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 54:
-+#line 393 "dtc-parser.y" /* yacc.c:1646 */
-+ { (yyval.integer) = (yyvsp[-2].integer) < (yyvsp[0].integer); }
-+#line 1861 "dtc-parser.tab.c" /* yacc.c:1646 */
-+ break;
-
--/* Line 1806 of yacc.c */
--#line 405 "dtc-parser.y"
-- { (yyval.integer) = (yyvsp[(1) - (3)].integer) != (yyvsp[(3) - (3)].integer); }
-+ case 55:
-+#line 394 "dtc-parser.y" /* yacc.c:1646 */
-+ { (yyval.integer) = (yyvsp[-2].integer) > (yyvsp[0].integer); }
-+#line 1867 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 56:
--
--/* Line 1806 of yacc.c */
--#line 410 "dtc-parser.y"
-- { (yyval.integer) = (yyvsp[(1) - (3)].integer) < (yyvsp[(3) - (3)].integer); }
-+#line 395 "dtc-parser.y" /* yacc.c:1646 */
-+ { (yyval.integer) = (yyvsp[-2].integer) <= (yyvsp[0].integer); }
-+#line 1873 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 57:
--
--/* Line 1806 of yacc.c */
--#line 411 "dtc-parser.y"
-- { (yyval.integer) = (yyvsp[(1) - (3)].integer) > (yyvsp[(3) - (3)].integer); }
-+#line 396 "dtc-parser.y" /* yacc.c:1646 */
-+ { (yyval.integer) = (yyvsp[-2].integer) >= (yyvsp[0].integer); }
-+#line 1879 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 58:
--
--/* Line 1806 of yacc.c */
--#line 412 "dtc-parser.y"
-- { (yyval.integer) = (yyvsp[(1) - (3)].integer) <= (yyvsp[(3) - (3)].integer); }
-+#line 400 "dtc-parser.y" /* yacc.c:1646 */
-+ { (yyval.integer) = (yyvsp[-2].integer) << (yyvsp[0].integer); }
-+#line 1885 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 59:
--
--/* Line 1806 of yacc.c */
--#line 413 "dtc-parser.y"
-- { (yyval.integer) = (yyvsp[(1) - (3)].integer) >= (yyvsp[(3) - (3)].integer); }
-- break;
--
-- case 60:
--
--/* Line 1806 of yacc.c */
--#line 417 "dtc-parser.y"
-- { (yyval.integer) = (yyvsp[(1) - (3)].integer) << (yyvsp[(3) - (3)].integer); }
-+#line 401 "dtc-parser.y" /* yacc.c:1646 */
-+ { (yyval.integer) = (yyvsp[-2].integer) >> (yyvsp[0].integer); }
-+#line 1891 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 61:
--
--/* Line 1806 of yacc.c */
--#line 418 "dtc-parser.y"
-- { (yyval.integer) = (yyvsp[(1) - (3)].integer) >> (yyvsp[(3) - (3)].integer); }
-+#line 406 "dtc-parser.y" /* yacc.c:1646 */
-+ { (yyval.integer) = (yyvsp[-2].integer) + (yyvsp[0].integer); }
-+#line 1897 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 63:
--
--/* Line 1806 of yacc.c */
--#line 423 "dtc-parser.y"
-- { (yyval.integer) = (yyvsp[(1) - (3)].integer) + (yyvsp[(3) - (3)].integer); }
-+ case 62:
-+#line 407 "dtc-parser.y" /* yacc.c:1646 */
-+ { (yyval.integer) = (yyvsp[-2].integer) - (yyvsp[0].integer); }
-+#line 1903 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 64:
-+#line 412 "dtc-parser.y" /* yacc.c:1646 */
-+ { (yyval.integer) = (yyvsp[-2].integer) * (yyvsp[0].integer); }
-+#line 1909 "dtc-parser.tab.c" /* yacc.c:1646 */
-+ break;
-
--/* Line 1806 of yacc.c */
--#line 424 "dtc-parser.y"
-- { (yyval.integer) = (yyvsp[(1) - (3)].integer) - (yyvsp[(3) - (3)].integer); }
-+ case 65:
-+#line 413 "dtc-parser.y" /* yacc.c:1646 */
-+ { (yyval.integer) = (yyvsp[-2].integer) / (yyvsp[0].integer); }
-+#line 1915 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 66:
--
--/* Line 1806 of yacc.c */
--#line 429 "dtc-parser.y"
-- { (yyval.integer) = (yyvsp[(1) - (3)].integer) * (yyvsp[(3) - (3)].integer); }
-+#line 414 "dtc-parser.y" /* yacc.c:1646 */
-+ { (yyval.integer) = (yyvsp[-2].integer) % (yyvsp[0].integer); }
-+#line 1921 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 67:
--
--/* Line 1806 of yacc.c */
--#line 430 "dtc-parser.y"
-- { (yyval.integer) = (yyvsp[(1) - (3)].integer) / (yyvsp[(3) - (3)].integer); }
-+ case 69:
-+#line 420 "dtc-parser.y" /* yacc.c:1646 */
-+ { (yyval.integer) = -(yyvsp[0].integer); }
-+#line 1927 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 68:
--
--/* Line 1806 of yacc.c */
--#line 431 "dtc-parser.y"
-- { (yyval.integer) = (yyvsp[(1) - (3)].integer) % (yyvsp[(3) - (3)].integer); }
-+ case 70:
-+#line 421 "dtc-parser.y" /* yacc.c:1646 */
-+ { (yyval.integer) = ~(yyvsp[0].integer); }
-+#line 1933 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 71:
--
--/* Line 1806 of yacc.c */
--#line 437 "dtc-parser.y"
-- { (yyval.integer) = -(yyvsp[(2) - (2)].integer); }
-+#line 422 "dtc-parser.y" /* yacc.c:1646 */
-+ { (yyval.integer) = !(yyvsp[0].integer); }
-+#line 1939 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 72:
--
--/* Line 1806 of yacc.c */
--#line 438 "dtc-parser.y"
-- { (yyval.integer) = ~(yyvsp[(2) - (2)].integer); }
-+#line 427 "dtc-parser.y" /* yacc.c:1646 */
-+ {
-+ (yyval.data) = empty_data;
-+ }
-+#line 1947 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 73:
--
--/* Line 1806 of yacc.c */
--#line 439 "dtc-parser.y"
-- { (yyval.integer) = !(yyvsp[(2) - (2)].integer); }
-+#line 431 "dtc-parser.y" /* yacc.c:1646 */
-+ {
-+ (yyval.data) = data_append_byte((yyvsp[-1].data), (yyvsp[0].byte));
-+ }
-+#line 1955 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 74:
--
--/* Line 1806 of yacc.c */
--#line 444 "dtc-parser.y"
-+#line 435 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.data) = empty_data;
-+ (yyval.data) = data_add_marker((yyvsp[-1].data), LABEL, (yyvsp[0].labelref));
- }
-+#line 1963 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 75:
--
--/* Line 1806 of yacc.c */
--#line 448 "dtc-parser.y"
-+#line 442 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.data) = data_append_byte((yyvsp[(1) - (2)].data), (yyvsp[(2) - (2)].byte));
-+ (yyval.nodelist) = NULL;
- }
-+#line 1971 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 76:
--
--/* Line 1806 of yacc.c */
--#line 452 "dtc-parser.y"
-+#line 446 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.data) = data_add_marker((yyvsp[(1) - (2)].data), LABEL, (yyvsp[(2) - (2)].labelref));
-+ (yyval.nodelist) = chain_node((yyvsp[-1].node), (yyvsp[0].nodelist));
- }
-+#line 1979 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 77:
--
--/* Line 1806 of yacc.c */
--#line 459 "dtc-parser.y"
-+#line 450 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.nodelist) = NULL;
-+ ERROR(&(yylsp[0]), "Properties must precede subnodes");
-+ YYERROR;
- }
-+#line 1988 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 78:
--
--/* Line 1806 of yacc.c */
--#line 463 "dtc-parser.y"
-+#line 458 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.nodelist) = chain_node((yyvsp[(1) - (2)].node), (yyvsp[(2) - (2)].nodelist));
-+ (yyval.node) = name_node((yyvsp[0].node), (yyvsp[-1].propnodename));
- }
-+#line 1996 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 79:
--
--/* Line 1806 of yacc.c */
--#line 467 "dtc-parser.y"
-+#line 462 "dtc-parser.y" /* yacc.c:1646 */
- {
-- ERROR(&(yylsp[(2) - (2)]), "Properties must precede subnodes");
-- YYERROR;
-+ (yyval.node) = name_node(build_node_delete(), (yyvsp[-1].propnodename));
- }
-+#line 2004 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 80:
--
--/* Line 1806 of yacc.c */
--#line 475 "dtc-parser.y"
-+#line 466 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.node) = name_node((yyvsp[(2) - (2)].node), (yyvsp[(1) - (2)].propnodename));
-+ add_label(&(yyvsp[0].node)->labels, (yyvsp[-1].labelref));
-+ (yyval.node) = (yyvsp[0].node);
- }
-+#line 2013 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 81:
-
--/* Line 1806 of yacc.c */
--#line 479 "dtc-parser.y"
-- {
-- (yyval.node) = name_node(build_node_delete(), (yyvsp[(2) - (3)].propnodename));
-- }
-- break;
--
-- case 82:
--
--/* Line 1806 of yacc.c */
--#line 483 "dtc-parser.y"
-- {
-- add_label(&(yyvsp[(2) - (2)].node)->labels, (yyvsp[(1) - (2)].labelref));
-- (yyval.node) = (yyvsp[(2) - (2)].node);
-- }
-- break;
--
--
--
--/* Line 1806 of yacc.c */
--#line 2235 "dtc-parser.tab.c"
-+#line 2017 "dtc-parser.tab.c" /* yacc.c:1646 */
- default: break;
- }
- /* User semantic actions sometimes alter yychar, and that requires
-@@ -2254,7 +2036,7 @@ yyreduce:
- *++yyvsp = yyval;
- *++yylsp = yyloc;
-
-- /* Now `shift' the result of the reduction. Determine what state
-+ /* Now 'shift' the result of the reduction. Determine what state
- that goes to, based on the state we popped back to and the rule
- number reduced by. */
-
-@@ -2269,9 +2051,9 @@ yyreduce:
- goto yynewstate;
-
-
--/*------------------------------------.
--| yyerrlab -- here on detecting error |
--`------------------------------------*/
-+/*--------------------------------------.
-+| yyerrlab -- here on detecting error. |
-+`--------------------------------------*/
- yyerrlab:
- /* Make sure we have latest lookahead translation. See comments at
- user semantic actions for why this is necessary. */
-@@ -2322,20 +2104,20 @@ yyerrlab:
- if (yyerrstatus == 3)
- {
- /* If just tried and failed to reuse lookahead token after an
-- error, discard it. */
-+ error, discard it. */
-
- if (yychar <= YYEOF)
-- {
-- /* Return failure if at end of input. */
-- if (yychar == YYEOF)
-- YYABORT;
-- }
-+ {
-+ /* Return failure if at end of input. */
-+ if (yychar == YYEOF)
-+ YYABORT;
-+ }
- else
-- {
-- yydestruct ("Error: discarding",
-- yytoken, &yylval, &yylloc);
-- yychar = YYEMPTY;
-- }
-+ {
-+ yydestruct ("Error: discarding",
-+ yytoken, &yylval, &yylloc);
-+ yychar = YYEMPTY;
-+ }
- }
-
- /* Else will try to reuse lookahead token after shifting the error
-@@ -2355,7 +2137,7 @@ yyerrorlab:
- goto yyerrorlab;
-
- yyerror_range[1] = yylsp[1-yylen];
-- /* Do not reclaim the symbols of the rule which action triggered
-+ /* Do not reclaim the symbols of the rule whose action triggered
- this YYERROR. */
- YYPOPSTACK (yylen);
- yylen = 0;
-@@ -2368,35 +2150,37 @@ yyerrorlab:
- | yyerrlab1 -- common code for both syntax error and YYERROR. |
- `-------------------------------------------------------------*/
- yyerrlab1:
-- yyerrstatus = 3; /* Each real token shifted decrements this. */
-+ yyerrstatus = 3; /* Each real token shifted decrements this. */
-
- for (;;)
- {
- yyn = yypact[yystate];
- if (!yypact_value_is_default (yyn))
-- {
-- yyn += YYTERROR;
-- if (0 <= yyn && yyn <= YYLAST && yycheck[yyn] == YYTERROR)
-- {
-- yyn = yytable[yyn];
-- if (0 < yyn)
-- break;
-- }
-- }
-+ {
-+ yyn += YYTERROR;
-+ if (0 <= yyn && yyn <= YYLAST && yycheck[yyn] == YYTERROR)
-+ {
-+ yyn = yytable[yyn];
-+ if (0 < yyn)
-+ break;
-+ }
-+ }
-
- /* Pop the current state because it cannot handle the error token. */
- if (yyssp == yyss)
-- YYABORT;
-+ YYABORT;
-
- yyerror_range[1] = *yylsp;
- yydestruct ("Error: popping",
-- yystos[yystate], yyvsp, yylsp);
-+ yystos[yystate], yyvsp, yylsp);
- YYPOPSTACK (1);
- yystate = *yyssp;
- YY_STACK_PRINT (yyss, yyssp);
- }
-
-+ YY_IGNORE_MAYBE_UNINITIALIZED_BEGIN
- *++yyvsp = yylval;
-+ YY_IGNORE_MAYBE_UNINITIALIZED_END
-
- yyerror_range[2] = yylloc;
- /* Using YYLLOC is tempting, but would change the location of
-@@ -2425,7 +2209,7 @@ yyabortlab:
- yyresult = 1;
- goto yyreturn;
-
--#if !defined(yyoverflow) || YYERROR_VERBOSE
-+#if !defined yyoverflow || YYERROR_VERBOSE
- /*-------------------------------------------------.
- | yyexhaustedlab -- memory exhaustion comes here. |
- `-------------------------------------------------*/
-@@ -2444,14 +2228,14 @@ yyreturn:
- yydestruct ("Cleanup: discarding lookahead",
- yytoken, &yylval, &yylloc);
- }
-- /* Do not reclaim the symbols of the rule which action triggered
-+ /* Do not reclaim the symbols of the rule whose action triggered
- this YYABORT or YYACCEPT. */
- YYPOPSTACK (yylen);
- YY_STACK_PRINT (yyss, yyssp);
- while (yyssp != yyss)
- {
- yydestruct ("Cleanup: popping",
-- yystos[*yyssp], yyvsp, yylsp);
-+ yystos[*yyssp], yyvsp, yylsp);
- YYPOPSTACK (1);
- }
- #ifndef yyoverflow
-@@ -2462,18 +2246,12 @@ yyreturn:
- if (yymsg != yymsgbuf)
- YYSTACK_FREE (yymsg);
- #endif
-- /* Make sure YYID is used. */
-- return YYID (yyresult);
-+ return yyresult;
- }
--
--
--
--/* Line 2067 of yacc.c */
--#line 489 "dtc-parser.y"
-+#line 472 "dtc-parser.y" /* yacc.c:1906 */
-
-
- void yyerror(char const *s)
- {
- ERROR(&yylloc, "%s", s);
- }
--
---- a/scripts/dtc/dtc-parser.tab.h_shipped
-+++ b/scripts/dtc/dtc-parser.tab.h_shipped
-@@ -1,19 +1,19 @@
--/* A Bison parser, made by GNU Bison 2.5. */
-+/* A Bison parser, made by GNU Bison 3.0.2. */
-
- /* Bison interface for Yacc-like parsers in C
--
-- Copyright (C) 1984, 1989-1990, 2000-2011 Free Software Foundation, Inc.
--
-+
-+ Copyright (C) 1984, 1989-1990, 2000-2013 Free Software Foundation, Inc.
-+
- This program is free software: you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation, either version 3 of the License, or
- (at your option) any later version.
--
-+
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
--
-+
- You should have received a copy of the GNU General Public License
- along with this program. If not, see <http://www.gnu.org/licenses/>. */
-
-@@ -26,50 +26,55 @@
- special exception, which will cause the skeleton and the resulting
- Bison output files to be licensed under the GNU General Public
- License without this special exception.
--
-+
- This special exception was added by the Free Software Foundation in
- version 2.2 of Bison. */
-
-+#ifndef YY_YY_DTC_PARSER_TAB_H_INCLUDED
-+# define YY_YY_DTC_PARSER_TAB_H_INCLUDED
-+/* Debug traces. */
-+#ifndef YYDEBUG
-+# define YYDEBUG 0
-+#endif
-+#if YYDEBUG
-+extern int yydebug;
-+#endif
-
--/* Tokens. */
-+/* Token type. */
- #ifndef YYTOKENTYPE
- # define YYTOKENTYPE
-- /* Put the tokens into the symbol table, so that GDB and other debuggers
-- know about them. */
-- enum yytokentype {
-- DT_V1 = 258,
-- DT_PLUGIN = 259,
-- DT_MEMRESERVE = 260,
-- DT_LSHIFT = 261,
-- DT_RSHIFT = 262,
-- DT_LE = 263,
-- DT_GE = 264,
-- DT_EQ = 265,
-- DT_NE = 266,
-- DT_AND = 267,
-- DT_OR = 268,
-- DT_BITS = 269,
-- DT_DEL_PROP = 270,
-- DT_DEL_NODE = 271,
-- DT_PROPNODENAME = 272,
-- DT_LITERAL = 273,
-- DT_CHAR_LITERAL = 274,
-- DT_BYTE = 275,
-- DT_STRING = 276,
-- DT_LABEL = 277,
-- DT_REF = 278,
-- DT_INCBIN = 279
-- };
-+ enum yytokentype
-+ {
-+ DT_V1 = 258,
-+ DT_MEMRESERVE = 259,
-+ DT_LSHIFT = 260,
-+ DT_RSHIFT = 261,
-+ DT_LE = 262,
-+ DT_GE = 263,
-+ DT_EQ = 264,
-+ DT_NE = 265,
-+ DT_AND = 266,
-+ DT_OR = 267,
-+ DT_BITS = 268,
-+ DT_DEL_PROP = 269,
-+ DT_DEL_NODE = 270,
-+ DT_PROPNODENAME = 271,
-+ DT_LITERAL = 272,
-+ DT_CHAR_LITERAL = 273,
-+ DT_BYTE = 274,
-+ DT_STRING = 275,
-+ DT_LABEL = 276,
-+ DT_REF = 277,
-+ DT_INCBIN = 278
-+ };
- #endif
-
--
--
-+/* Value type. */
- #if ! defined YYSTYPE && ! defined YYSTYPE_IS_DECLARED
--typedef union YYSTYPE
-+typedef union YYSTYPE YYSTYPE;
-+union YYSTYPE
- {
--
--/* Line 2068 of yacc.c */
--#line 39 "dtc-parser.y"
-+#line 38 "dtc-parser.y" /* yacc.c:1909 */
-
- char *propnodename;
- char *labelref;
-@@ -87,32 +92,30 @@ typedef union YYSTYPE
- struct node *nodelist;
- struct reserve_info *re;
- uint64_t integer;
-- int is_plugin;
--
--
-
--/* Line 2068 of yacc.c */
--#line 96 "dtc-parser.tab.h"
--} YYSTYPE;
-+#line 97 "dtc-parser.tab.h" /* yacc.c:1909 */
-+};
- # define YYSTYPE_IS_TRIVIAL 1
--# define yystype YYSTYPE /* obsolescent; will be withdrawn */
- # define YYSTYPE_IS_DECLARED 1
- #endif
-
--extern YYSTYPE yylval;
--
-+/* Location type. */
- #if ! defined YYLTYPE && ! defined YYLTYPE_IS_DECLARED
--typedef struct YYLTYPE
-+typedef struct YYLTYPE YYLTYPE;
-+struct YYLTYPE
- {
- int first_line;
- int first_column;
- int last_line;
- int last_column;
--} YYLTYPE;
--# define yyltype YYLTYPE /* obsolescent; will be withdrawn */
-+};
- # define YYLTYPE_IS_DECLARED 1
- # define YYLTYPE_IS_TRIVIAL 1
- #endif
-
-+
-+extern YYSTYPE yylval;
- extern YYLTYPE yylloc;
-+int yyparse (void);
-
-+#endif /* !YY_YY_DTC_PARSER_TAB_H_INCLUDED */
---- a/scripts/dtc/dtc-parser.y
-+++ b/scripts/dtc/dtc-parser.y
-@@ -19,7 +19,6 @@
- */
- %{
- #include <stdio.h>
--#include <inttypes.h>
-
- #include "dtc.h"
- #include "srcpos.h"
-@@ -53,11 +52,9 @@ extern bool treesource_error;
- struct node *nodelist;
- struct reserve_info *re;
- uint64_t integer;
-- int is_plugin;
- }
-
- %token DT_V1
--%token DT_PLUGIN
- %token DT_MEMRESERVE
- %token DT_LSHIFT DT_RSHIFT DT_LE DT_GE DT_EQ DT_NE DT_AND DT_OR
- %token DT_BITS
-@@ -74,7 +71,6 @@ extern bool treesource_error;
-
- %type <data> propdata
- %type <data> propdataprefix
--%type <is_plugin> plugindecl
- %type <re> memreserve
- %type <re> memreserves
- %type <array> arrayprefix
-@@ -105,23 +101,10 @@ extern bool treesource_error;
- %%
-
- sourcefile:
-- DT_V1 ';' plugindecl memreserves devicetree
-+ DT_V1 ';' memreserves devicetree
- {
-- $5->is_plugin = $3;
-- $5->is_root = 1;
-- the_boot_info = build_boot_info($4, $5,
-- guess_boot_cpuid($5));
-- }
-- ;
--
--plugindecl:
-- /* empty */
-- {
-- $$ = 0;
-- }
-- | DT_PLUGIN ';'
-- {
-- $$ = 1;
-+ the_boot_info = build_boot_info($3, $4,
-+ guess_boot_cpuid($4));
- }
- ;
-
---- a/scripts/dtc/dtc.c
-+++ b/scripts/dtc/dtc.c
-@@ -29,7 +29,6 @@ int reservenum; /* Number of memory res
- int minsize; /* Minimum blob size */
- int padsize; /* Additional padding to blob */
- int phandle_format = PHANDLE_BOTH; /* Use linux,phandle or phandle properties */
--int symbol_fixup_support = 0;
-
- static void fill_fullpaths(struct node *tree, const char *prefix)
- {
-@@ -52,7 +51,7 @@ static void fill_fullpaths(struct node *
- #define FDT_VERSION(version) _FDT_VERSION(version)
- #define _FDT_VERSION(version) #version
- static const char usage_synopsis[] = "dtc [options] <input file>";
--static const char usage_short_opts[] = "qI:O:o:V:d:R:S:p:fb:i:H:sW:E:hv@";
-+static const char usage_short_opts[] = "qI:O:o:V:d:R:S:p:fb:i:H:sW:E:hv";
- static struct option const usage_long_opts[] = {
- {"quiet", no_argument, NULL, 'q'},
- {"in-format", a_argument, NULL, 'I'},
-@@ -70,7 +69,6 @@ static struct option const usage_long_op
- {"phandle", a_argument, NULL, 'H'},
- {"warning", a_argument, NULL, 'W'},
- {"error", a_argument, NULL, 'E'},
-- {"symbols", a_argument, NULL, '@'},
- {"help", no_argument, NULL, 'h'},
- {"version", no_argument, NULL, 'v'},
- {NULL, no_argument, NULL, 0x0},
-@@ -101,7 +99,6 @@ static const char * const usage_opts_hel
- "\t\tboth - Both \"linux,phandle\" and \"phandle\" properties",
- "\n\tEnable/disable warnings (prefix with \"no-\")",
- "\n\tEnable/disable errors (prefix with \"no-\")",
-- "\n\tSymbols and Fixups support",
- "\n\tPrint this help and exit",
- "\n\tPrint version and exit",
- NULL,
-@@ -189,9 +186,7 @@ int main(int argc, char *argv[])
- case 'E':
- parse_checks_option(false, true, optarg);
- break;
-- case '@':
-- symbol_fixup_support = 1;
-- break;
-+
- case 'h':
- usage(NULL);
- default:
---- a/scripts/dtc/dtc.h
-+++ b/scripts/dtc/dtc.h
-@@ -54,7 +54,6 @@ extern int reservenum; /* Number of mem
- extern int minsize; /* Minimum blob size */
- extern int padsize; /* Additional padding to blob */
- extern int phandle_format; /* Use linux,phandle or phandle properties */
--extern int symbol_fixup_support;/* enable symbols & fixup support */
-
- #define PHANDLE_LEGACY 0x1
- #define PHANDLE_EPAPR 0x2
-@@ -133,25 +132,6 @@ struct label {
- struct label *next;
- };
-
--struct fixup_entry {
-- int offset;
-- struct node *node;
-- struct property *prop;
-- struct fixup_entry *next;
--};
--
--struct fixup {
-- char *ref;
-- struct fixup_entry *entries;
-- struct fixup *next;
--};
--
--struct symbol {
-- struct label *label;
-- struct node *node;
-- struct symbol *next;
--};
--
- struct property {
- bool deleted;
- char *name;
-@@ -178,12 +158,6 @@ struct node {
- int addr_cells, size_cells;
-
- struct label *labels;
--
-- int is_root;
-- int is_plugin;
-- struct fixup *fixups;
-- struct symbol *symbols;
-- struct fixup_entry *local_fixups;
- };
-
- #define for_each_label_withdel(l0, l) \
-@@ -207,18 +181,6 @@ struct node {
- for_each_child_withdel(n, c) \
- if (!(c)->deleted)
-
--#define for_each_fixup(n, f) \
-- for ((f) = (n)->fixups; (f); (f) = (f)->next)
--
--#define for_each_fixup_entry(f, fe) \
-- for ((fe) = (f)->entries; (fe); (fe) = (fe)->next)
--
--#define for_each_symbol(n, s) \
-- for ((s) = (n)->symbols; (s); (s) = (s)->next)
--
--#define for_each_local_fixup_entry(n, fe) \
-- for ((fe) = (n)->local_fixups; (fe); (fe) = (fe)->next)
--
- void add_label(struct label **labels, char *label);
- void delete_labels(struct label **labels);
-
---- a/scripts/dtc/flattree.c
-+++ b/scripts/dtc/flattree.c
-@@ -262,12 +262,6 @@ static void flatten_tree(struct node *tr
- struct property *prop;
- struct node *child;
- bool seen_name_prop = false;
-- struct symbol *sym;
-- struct fixup *f;
-- struct fixup_entry *fe;
-- char *name, *s;
-- const char *fullpath;
-- int namesz, nameoff, vallen;
-
- if (tree->deleted)
- return;
-@@ -282,6 +276,8 @@ static void flatten_tree(struct node *tr
- emit->align(etarget, sizeof(cell_t));
-
- for_each_property(tree, prop) {
-+ int nameoff;
-+
- if (streq(prop->name, "name"))
- seen_name_prop = true;
-
-@@ -314,139 +310,6 @@ static void flatten_tree(struct node *tr
- flatten_tree(child, emit, etarget, strbuf, vi);
- }
-
-- if (!symbol_fixup_support)
-- goto no_symbols;
--
-- /* add the symbol nodes (if any) */
-- if (tree->symbols) {
--
-- emit->beginnode(etarget, NULL);
-- emit->string(etarget, "__symbols__", 0);
-- emit->align(etarget, sizeof(cell_t));
--
-- for_each_symbol(tree, sym) {
--
-- vallen = strlen(sym->node->fullpath);
--
-- nameoff = stringtable_insert(strbuf, sym->label->label);
--
-- emit->property(etarget, NULL);
-- emit->cell(etarget, vallen + 1);
-- emit->cell(etarget, nameoff);
--
-- if ((vi->flags & FTF_VARALIGN) && vallen >= 8)
-- emit->align(etarget, 8);
--
-- emit->string(etarget, sym->node->fullpath,
-- strlen(sym->node->fullpath));
-- emit->align(etarget, sizeof(cell_t));
-- }
--
-- emit->endnode(etarget, NULL);
-- }
--
-- /* add the fixup nodes */
-- if (tree->fixups) {
--
-- /* emit the external fixups */
-- emit->beginnode(etarget, NULL);
-- emit->string(etarget, "__fixups__", 0);
-- emit->align(etarget, sizeof(cell_t));
--
-- for_each_fixup(tree, f) {
--
-- namesz = 0;
-- for_each_fixup_entry(f, fe) {
-- fullpath = fe->node->fullpath;
-- if (fullpath[0] == '\0')
-- fullpath = "/";
-- namesz += strlen(fullpath) + 1;
-- namesz += strlen(fe->prop->name) + 1;
-- namesz += 32; /* space for :<number> + '\0' */
-- }
--
-- name = xmalloc(namesz);
--
-- s = name;
-- for_each_fixup_entry(f, fe) {
-- fullpath = fe->node->fullpath;
-- if (fullpath[0] == '\0')
-- fullpath = "/";
-- snprintf(s, name + namesz - s, "%s:%s:%d",
-- fullpath,
-- fe->prop->name, fe->offset);
-- s += strlen(s) + 1;
-- }
--
-- nameoff = stringtable_insert(strbuf, f->ref);
-- vallen = s - name - 1;
--
-- emit->property(etarget, NULL);
-- emit->cell(etarget, vallen + 1);
-- emit->cell(etarget, nameoff);
--
-- if ((vi->flags & FTF_VARALIGN) && vallen >= 8)
-- emit->align(etarget, 8);
--
-- emit->string(etarget, name, vallen);
-- emit->align(etarget, sizeof(cell_t));
--
-- free(name);
-- }
--
-- emit->endnode(etarget, tree->labels);
-- }
--
-- /* add the local fixup property */
-- if (tree->local_fixups) {
--
-- /* emit the external fixups */
-- emit->beginnode(etarget, NULL);
-- emit->string(etarget, "__local_fixups__", 0);
-- emit->align(etarget, sizeof(cell_t));
--
-- namesz = 0;
-- for_each_local_fixup_entry(tree, fe) {
-- fullpath = fe->node->fullpath;
-- if (fullpath[0] == '\0')
-- fullpath = "/";
-- namesz += strlen(fullpath) + 1;
-- namesz += strlen(fe->prop->name) + 1;
-- namesz += 32; /* space for :<number> + '\0' */
-- }
--
-- name = xmalloc(namesz);
--
-- s = name;
-- for_each_local_fixup_entry(tree, fe) {
-- fullpath = fe->node->fullpath;
-- if (fullpath[0] == '\0')
-- fullpath = "/";
-- snprintf(s, name + namesz - s, "%s:%s:%d",
-- fullpath, fe->prop->name,
-- fe->offset);
-- s += strlen(s) + 1;
-- }
--
-- nameoff = stringtable_insert(strbuf, "fixup");
-- vallen = s - name - 1;
--
-- emit->property(etarget, NULL);
-- emit->cell(etarget, vallen + 1);
-- emit->cell(etarget, nameoff);
--
-- if ((vi->flags & FTF_VARALIGN) && vallen >= 8)
-- emit->align(etarget, 8);
--
-- emit->string(etarget, name, vallen);
-- emit->align(etarget, sizeof(cell_t));
--
-- free(name);
--
-- emit->endnode(etarget, tree->labels);
-- }
--
--no_symbols:
- emit->endnode(etarget, tree->labels);
- }
-
---- a/scripts/dtc/version_gen.h
-+++ b/scripts/dtc/version_gen.h
-@@ -1 +1 @@
--#define DTC_VERSION "DTC 1.4.1-g9d3649bd-dirty"
-+#define DTC_VERSION "DTC 1.4.1-g9d3649bd"
diff --git a/target/linux/brcm2708/patches-4.4/0176-scripts-dtc-Update-to-upstream-version-1.4.1.patch b/target/linux/brcm2708/patches-4.4/0176-scripts-dtc-Update-to-upstream-version-1.4.1.patch
deleted file mode 100644
index 7e3791c..0000000
--- a/target/linux/brcm2708/patches-4.4/0176-scripts-dtc-Update-to-upstream-version-1.4.1.patch
+++ /dev/null
@@ -1,2736 +0,0 @@
-From 6bf7e9cf8ce65ea8f0ba41084addb86a96dd9fdb Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 10 Aug 2015 09:49:15 +0100
-Subject: [PATCH] scripts/dtc: Update to upstream version 1.4.1
-
-Includes the new localfixups format.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- scripts/dtc/checks.c | 105 ++++-
- scripts/dtc/dtc-lexer.l | 5 +
- scripts/dtc/dtc-lexer.lex.c_shipped | 490 ++++++++++++------------
- scripts/dtc/dtc-parser.tab.c_shipped | 722 ++++++++++++++++++-----------------
- scripts/dtc/dtc-parser.tab.h_shipped | 46 +--
- scripts/dtc/dtc-parser.y | 22 +-
- scripts/dtc/dtc.c | 9 +-
- scripts/dtc/dtc.h | 40 ++
- scripts/dtc/flattree.c | 202 ++++++++++
- scripts/dtc/version_gen.h | 2 +-
- 10 files changed, 1021 insertions(+), 622 deletions(-)
-
---- a/scripts/dtc/checks.c
-+++ b/scripts/dtc/checks.c
-@@ -458,6 +458,8 @@ static void fixup_phandle_references(str
- struct node *node, struct property *prop)
- {
- struct marker *m = prop->val.markers;
-+ struct fixup *f, **fp;
-+ struct fixup_entry *fe, **fep;
- struct node *refnode;
- cell_t phandle;
-
-@@ -466,11 +468,69 @@ static void fixup_phandle_references(str
-
- refnode = get_node_by_ref(dt, m->ref);
- if (! refnode) {
-- FAIL(c, "Reference to non-existent node or label \"%s\"\n",
-- m->ref);
-+ if (!dt->is_plugin) {
-+ FAIL(c, "Reference to non-existent node or label \"%s\"\n",
-+ m->ref);
-+ continue;
-+ }
-+
-+ /* allocate fixup entry */
-+ fe = xmalloc(sizeof(*fe));
-+
-+ fe->node = node;
-+ fe->prop = prop;
-+ fe->offset = m->offset;
-+ fe->next = NULL;
-+
-+ /* search for an already existing fixup */
-+ for_each_fixup(dt, f)
-+ if (strcmp(f->ref, m->ref) == 0)
-+ break;
-+
-+ /* no fixup found, add new */
-+ if (f == NULL) {
-+ f = xmalloc(sizeof(*f));
-+ f->ref = m->ref;
-+ f->entries = NULL;
-+ f->next = NULL;
-+
-+ /* add it to the tree */
-+ fp = &dt->fixups;
-+ while (*fp)
-+ fp = &(*fp)->next;
-+ *fp = f;
-+ }
-+
-+ /* and now append fixup entry */
-+ fep = &f->entries;
-+ while (*fep)
-+ fep = &(*fep)->next;
-+ *fep = fe;
-+
-+ /* mark the entry as unresolved */
-+ *((cell_t *)(prop->val.val + m->offset)) =
-+ cpu_to_fdt32(0xdeadbeef);
- continue;
- }
-
-+ /* if it's a local reference, we need to record it */
-+ if (symbol_fixup_support) {
-+
-+ /* allocate a new local fixup entry */
-+ fe = xmalloc(sizeof(*fe));
-+
-+ fe->node = node;
-+ fe->prop = prop;
-+ fe->offset = m->offset;
-+ fe->next = NULL;
-+
-+ /* append it to the local fixups */
-+ fep = &dt->local_fixups;
-+ while (*fep)
-+ fep = &(*fep)->next;
-+ *fep = fe;
-+ }
-+
- phandle = get_node_phandle(dt, refnode);
- *((cell_t *)(prop->val.val + m->offset)) = cpu_to_fdt32(phandle);
- }
-@@ -652,6 +712,45 @@ static void check_obsolete_chosen_interr
- }
- TREE_WARNING(obsolete_chosen_interrupt_controller, NULL);
-
-+static void check_auto_label_phandles(struct check *c, struct node *dt,
-+ struct node *node)
-+{
-+ struct label *l;
-+ struct symbol *s, **sp;
-+ int has_label;
-+
-+ if (!symbol_fixup_support)
-+ return;
-+
-+ has_label = 0;
-+ for_each_label(node->labels, l) {
-+ has_label = 1;
-+ break;
-+ }
-+
-+ if (!has_label)
-+ return;
-+
-+ /* force allocation of a phandle for this node */
-+ (void)get_node_phandle(dt, node);
-+
-+ /* add the symbol */
-+ for_each_label(node->labels, l) {
-+
-+ s = xmalloc(sizeof(*s));
-+ s->label = l;
-+ s->node = node;
-+ s->next = NULL;
-+
-+ /* add it to the symbols list */
-+ sp = &dt->symbols;
-+ while (*sp)
-+ sp = &((*sp)->next);
-+ *sp = s;
-+ }
-+}
-+NODE_WARNING(auto_label_phandles, NULL);
-+
- static struct check *check_table[] = {
- &duplicate_node_names, &duplicate_property_names,
- &node_name_chars, &node_name_format, &property_name_chars,
-@@ -670,6 +769,8 @@ static struct check *check_table[] = {
- &avoid_default_addr_size,
- &obsolete_chosen_interrupt_controller,
-
-+ &auto_label_phandles,
-+
- &always_fail,
- };
-
---- a/scripts/dtc/dtc-lexer.l
-+++ b/scripts/dtc/dtc-lexer.l
-@@ -113,6 +113,11 @@ static void lexical_error(const char *fm
- return DT_V1;
- }
-
-+<*>"/plugin/" {
-+ DPRINT("Keyword: /plugin/\n");
-+ return DT_PLUGIN;
-+ }
-+
- <*>"/memreserve/" {
- DPRINT("Keyword: /memreserve/\n");
- BEGIN_DEFAULT();
---- a/scripts/dtc/dtc-lexer.lex.c_shipped
-+++ b/scripts/dtc/dtc-lexer.lex.c_shipped
-@@ -9,7 +9,7 @@
- #define FLEX_SCANNER
- #define YY_FLEX_MAJOR_VERSION 2
- #define YY_FLEX_MINOR_VERSION 5
--#define YY_FLEX_SUBMINOR_VERSION 39
-+#define YY_FLEX_SUBMINOR_VERSION 35
- #if YY_FLEX_SUBMINOR_VERSION > 0
- #define FLEX_BETA
- #endif
-@@ -162,12 +162,7 @@ typedef unsigned int flex_uint32_t;
- typedef struct yy_buffer_state *YY_BUFFER_STATE;
- #endif
-
--#ifndef YY_TYPEDEF_YY_SIZE_T
--#define YY_TYPEDEF_YY_SIZE_T
--typedef size_t yy_size_t;
--#endif
--
--extern yy_size_t yyleng;
-+extern int yyleng;
-
- extern FILE *yyin, *yyout;
-
-@@ -176,7 +171,6 @@ extern FILE *yyin, *yyout;
- #define EOB_ACT_LAST_MATCH 2
-
- #define YY_LESS_LINENO(n)
-- #define YY_LINENO_REWIND_TO(ptr)
-
- /* Return all but the first "n" matched characters back to the input stream. */
- #define yyless(n) \
-@@ -194,6 +188,11 @@ extern FILE *yyin, *yyout;
-
- #define unput(c) yyunput( c, (yytext_ptr) )
-
-+#ifndef YY_TYPEDEF_YY_SIZE_T
-+#define YY_TYPEDEF_YY_SIZE_T
-+typedef size_t yy_size_t;
-+#endif
-+
- #ifndef YY_STRUCT_YY_BUFFER_STATE
- #define YY_STRUCT_YY_BUFFER_STATE
- struct yy_buffer_state
-@@ -211,7 +210,7 @@ struct yy_buffer_state
- /* Number of characters read into yy_ch_buf, not including EOB
- * characters.
- */
-- yy_size_t yy_n_chars;
-+ int yy_n_chars;
-
- /* Whether we "own" the buffer - i.e., we know we created it,
- * and can realloc() it to grow it, and should free() it to
-@@ -281,8 +280,8 @@ static YY_BUFFER_STATE * yy_buffer_stack
-
- /* yy_hold_char holds the character lost when yytext is formed. */
- static char yy_hold_char;
--static yy_size_t yy_n_chars; /* number of characters read into yy_ch_buf */
--yy_size_t yyleng;
-+static int yy_n_chars; /* number of characters read into yy_ch_buf */
-+int yyleng;
-
- /* Points to current character in buffer. */
- static char *yy_c_buf_p = (char *) 0;
-@@ -310,7 +309,7 @@ static void yy_init_buffer (YY_BUFFER_ST
-
- YY_BUFFER_STATE yy_scan_buffer (char *base,yy_size_t size );
- YY_BUFFER_STATE yy_scan_string (yyconst char *yy_str );
--YY_BUFFER_STATE yy_scan_bytes (yyconst char *bytes,yy_size_t len );
-+YY_BUFFER_STATE yy_scan_bytes (yyconst char *bytes,int len );
-
- void *yyalloc (yy_size_t );
- void *yyrealloc (void *,yy_size_t );
-@@ -342,7 +341,7 @@ void yyfree (void * );
-
- /* Begin user sect3 */
-
--#define yywrap() 1
-+#define yywrap(n) 1
- #define YY_SKIP_YYWRAP
-
- typedef unsigned char YY_CHAR;
-@@ -373,8 +372,8 @@ static void yy_fatal_error (yyconst char
- *yy_cp = '\0'; \
- (yy_c_buf_p) = yy_cp;
-
--#define YY_NUM_RULES 30
--#define YY_END_OF_BUFFER 31
-+#define YY_NUM_RULES 31
-+#define YY_END_OF_BUFFER 32
- /* This struct is not used in this scanner,
- but its presence is necessary. */
- struct yy_trans_info
-@@ -382,25 +381,26 @@ struct yy_trans_info
- flex_int32_t yy_verify;
- flex_int32_t yy_nxt;
- };
--static yyconst flex_int16_t yy_accept[159] =
-+static yyconst flex_int16_t yy_accept[166] =
- { 0,
-- 0, 0, 0, 0, 0, 0, 0, 0, 31, 29,
-- 18, 18, 29, 29, 29, 29, 29, 29, 29, 29,
-- 29, 29, 29, 29, 29, 29, 15, 16, 16, 29,
-- 16, 10, 10, 18, 26, 0, 3, 0, 27, 12,
-- 0, 0, 11, 0, 0, 0, 0, 0, 0, 0,
-- 21, 23, 25, 24, 22, 0, 9, 28, 0, 0,
-- 0, 14, 14, 16, 16, 16, 10, 10, 10, 0,
-- 12, 0, 11, 0, 0, 0, 20, 0, 0, 0,
-- 0, 0, 0, 0, 0, 16, 10, 10, 10, 0,
-- 13, 19, 0, 0, 0, 0, 0, 0, 0, 0,
--
-- 0, 16, 0, 0, 0, 0, 0, 0, 0, 0,
-- 0, 16, 6, 0, 0, 0, 0, 0, 0, 2,
-- 0, 0, 0, 0, 0, 0, 0, 0, 4, 17,
-- 0, 0, 2, 0, 0, 0, 0, 0, 0, 0,
-- 0, 0, 0, 0, 0, 1, 0, 0, 0, 0,
-- 5, 8, 0, 0, 0, 0, 7, 0
-+ 0, 0, 0, 0, 0, 0, 0, 0, 32, 30,
-+ 19, 19, 30, 30, 30, 30, 30, 30, 30, 30,
-+ 30, 30, 30, 30, 30, 30, 16, 17, 17, 30,
-+ 17, 11, 11, 19, 27, 0, 3, 0, 28, 13,
-+ 0, 0, 12, 0, 0, 0, 0, 0, 0, 0,
-+ 0, 22, 24, 26, 25, 23, 0, 10, 29, 0,
-+ 0, 0, 15, 15, 17, 17, 17, 11, 11, 11,
-+ 0, 13, 0, 12, 0, 0, 0, 21, 0, 0,
-+ 0, 0, 0, 0, 0, 0, 0, 17, 11, 11,
-+ 11, 0, 14, 20, 0, 0, 0, 0, 0, 0,
-+
-+ 0, 0, 0, 0, 17, 0, 0, 0, 0, 0,
-+ 0, 0, 0, 0, 0, 17, 7, 0, 0, 0,
-+ 0, 0, 0, 0, 2, 0, 0, 0, 0, 0,
-+ 0, 0, 0, 0, 4, 18, 0, 0, 5, 2,
-+ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
-+ 0, 0, 1, 0, 0, 0, 0, 6, 9, 0,
-+ 0, 0, 0, 8, 0
- } ;
-
- static yyconst flex_int32_t yy_ec[256] =
-@@ -416,9 +416,9 @@ static yyconst flex_int32_t yy_ec[256] =
- 22, 22, 22, 22, 24, 22, 22, 25, 22, 22,
- 1, 26, 27, 1, 22, 1, 21, 28, 29, 30,
-
-- 31, 21, 22, 22, 32, 22, 22, 33, 34, 35,
-- 36, 37, 22, 38, 39, 40, 41, 42, 22, 25,
-- 43, 22, 44, 45, 46, 1, 1, 1, 1, 1,
-+ 31, 21, 32, 22, 33, 22, 22, 34, 35, 36,
-+ 37, 38, 22, 39, 40, 41, 42, 43, 22, 25,
-+ 44, 22, 45, 46, 47, 1, 1, 1, 1, 1,
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
-@@ -435,163 +435,165 @@ static yyconst flex_int32_t yy_ec[256] =
- 1, 1, 1, 1, 1
- } ;
-
--static yyconst flex_int32_t yy_meta[47] =
-+static yyconst flex_int32_t yy_meta[48] =
- { 0,
- 1, 1, 1, 1, 1, 1, 2, 3, 1, 2,
- 2, 2, 4, 5, 5, 5, 6, 1, 1, 1,
- 7, 8, 8, 8, 8, 1, 1, 7, 7, 7,
- 7, 8, 8, 8, 8, 8, 8, 8, 8, 8,
-- 8, 8, 8, 3, 1, 4
-+ 8, 8, 8, 8, 3, 1, 4
- } ;
-
--static yyconst flex_int16_t yy_base[173] =
-+static yyconst flex_int16_t yy_base[180] =
- { 0,
-- 0, 383, 34, 382, 65, 381, 37, 105, 387, 391,
-- 54, 111, 367, 110, 109, 109, 112, 41, 366, 104,
-- 367, 338, 124, 117, 0, 144, 391, 0, 121, 0,
-- 135, 155, 140, 179, 391, 160, 391, 379, 391, 0,
-- 368, 141, 391, 167, 370, 376, 346, 103, 342, 345,
-- 391, 391, 391, 391, 391, 358, 391, 391, 175, 342,
-- 338, 391, 355, 0, 185, 339, 184, 347, 346, 0,
-- 0, 322, 175, 357, 175, 363, 352, 324, 330, 323,
-- 332, 326, 201, 324, 329, 322, 391, 333, 181, 309,
-- 391, 341, 340, 313, 320, 338, 178, 311, 146, 317,
--
-- 314, 315, 335, 331, 303, 300, 309, 299, 308, 188,
-- 336, 335, 391, 305, 320, 281, 283, 271, 203, 288,
-- 281, 271, 266, 264, 245, 242, 208, 104, 391, 391,
-- 244, 218, 204, 219, 206, 224, 201, 212, 204, 229,
-- 215, 208, 207, 200, 219, 391, 233, 221, 200, 181,
-- 391, 391, 149, 122, 86, 41, 391, 391, 245, 251,
-- 259, 263, 267, 273, 280, 284, 292, 300, 304, 310,
-- 318, 326
-+ 0, 393, 35, 392, 66, 391, 38, 107, 397, 401,
-+ 55, 113, 377, 112, 111, 111, 114, 42, 376, 106,
-+ 377, 347, 126, 120, 0, 147, 401, 0, 124, 0,
-+ 137, 158, 170, 163, 401, 153, 401, 389, 401, 0,
-+ 378, 120, 401, 131, 380, 386, 355, 139, 351, 355,
-+ 351, 401, 401, 401, 401, 401, 367, 401, 401, 185,
-+ 350, 346, 401, 364, 0, 185, 347, 189, 356, 355,
-+ 0, 0, 330, 180, 366, 141, 372, 361, 332, 338,
-+ 331, 341, 334, 326, 205, 331, 337, 329, 401, 341,
-+ 167, 316, 401, 349, 348, 320, 328, 346, 180, 318,
-+
-+ 324, 209, 324, 320, 322, 342, 338, 309, 306, 315,
-+ 305, 315, 312, 192, 342, 341, 401, 293, 306, 282,
-+ 268, 252, 255, 203, 285, 282, 272, 268, 252, 233,
-+ 232, 239, 208, 107, 401, 401, 238, 211, 401, 211,
-+ 212, 208, 228, 203, 215, 207, 233, 222, 212, 211,
-+ 203, 227, 401, 237, 225, 204, 185, 401, 401, 149,
-+ 128, 88, 42, 401, 401, 253, 259, 267, 271, 275,
-+ 281, 288, 292, 300, 308, 312, 318, 326, 334
- } ;
-
--static yyconst flex_int16_t yy_def[173] =
-+static yyconst flex_int16_t yy_def[180] =
- { 0,
-- 158, 1, 1, 3, 158, 5, 1, 1, 158, 158,
-- 158, 158, 158, 159, 160, 161, 158, 158, 158, 158,
-- 162, 158, 158, 158, 163, 162, 158, 164, 165, 164,
-- 164, 158, 158, 158, 158, 159, 158, 159, 158, 166,
-- 158, 161, 158, 161, 167, 168, 158, 158, 158, 158,
-- 158, 158, 158, 158, 158, 162, 158, 158, 158, 158,
-- 158, 158, 162, 164, 165, 164, 158, 158, 158, 169,
-- 166, 170, 161, 167, 167, 168, 158, 158, 158, 158,
-- 158, 158, 158, 158, 158, 164, 158, 158, 169, 170,
-- 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
--
-- 158, 164, 158, 158, 158, 158, 158, 158, 158, 171,
-- 158, 164, 158, 158, 158, 158, 158, 158, 171, 158,
-- 171, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-- 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-- 172, 158, 158, 158, 172, 158, 172, 158, 158, 158,
-- 158, 158, 158, 158, 158, 158, 158, 0, 158, 158,
-- 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-- 158, 158
-+ 165, 1, 1, 3, 165, 5, 1, 1, 165, 165,
-+ 165, 165, 165, 166, 167, 168, 165, 165, 165, 165,
-+ 169, 165, 165, 165, 170, 169, 165, 171, 172, 171,
-+ 171, 165, 165, 165, 165, 166, 165, 166, 165, 173,
-+ 165, 168, 165, 168, 174, 175, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 169, 165, 165, 165,
-+ 165, 165, 165, 169, 171, 172, 171, 165, 165, 165,
-+ 176, 173, 177, 168, 174, 174, 175, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 165, 171, 165, 165,
-+ 176, 177, 165, 165, 165, 165, 165, 165, 165, 165,
-+
-+ 165, 165, 165, 165, 171, 165, 165, 165, 165, 165,
-+ 165, 165, 165, 178, 165, 171, 165, 165, 165, 165,
-+ 165, 165, 165, 178, 165, 178, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 165, 179, 165, 165,
-+ 165, 179, 165, 179, 165, 165, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 0, 165, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 165, 165, 165
- } ;
-
--static yyconst flex_int16_t yy_nxt[438] =
-+static yyconst flex_int16_t yy_nxt[449] =
- { 0,
- 10, 11, 12, 11, 13, 14, 10, 15, 16, 10,
- 10, 10, 17, 10, 10, 10, 10, 18, 19, 20,
- 21, 21, 21, 21, 21, 10, 10, 21, 21, 21,
- 21, 21, 21, 21, 21, 21, 21, 21, 21, 21,
-- 21, 21, 21, 10, 22, 10, 24, 25, 25, 25,
-- 32, 33, 33, 157, 26, 34, 34, 34, 51, 52,
-- 27, 26, 26, 26, 26, 10, 11, 12, 11, 13,
-- 14, 28, 15, 16, 28, 28, 28, 24, 28, 28,
-- 28, 10, 18, 19, 20, 29, 29, 29, 29, 29,
-- 30, 10, 29, 29, 29, 29, 29, 29, 29, 29,
--
-- 29, 29, 29, 29, 29, 29, 29, 29, 10, 22,
-- 10, 23, 34, 34, 34, 37, 39, 43, 32, 33,
-- 33, 45, 54, 55, 46, 59, 45, 64, 156, 46,
-- 64, 64, 64, 79, 44, 38, 59, 57, 134, 47,
-- 135, 48, 80, 49, 47, 50, 48, 99, 61, 43,
-- 50, 110, 41, 67, 67, 67, 60, 63, 63, 63,
-- 57, 155, 68, 69, 63, 37, 44, 66, 67, 67,
-- 67, 63, 63, 63, 63, 73, 59, 68, 69, 70,
-- 34, 34, 34, 43, 75, 38, 154, 92, 83, 83,
-- 83, 64, 44, 120, 64, 64, 64, 67, 67, 67,
--
-- 44, 57, 99, 68, 69, 107, 68, 69, 120, 127,
-- 108, 153, 152, 121, 83, 83, 83, 133, 133, 133,
-- 146, 133, 133, 133, 146, 140, 140, 140, 121, 141,
-- 140, 140, 140, 151, 141, 158, 150, 149, 148, 144,
-- 147, 143, 142, 139, 147, 36, 36, 36, 36, 36,
-- 36, 36, 36, 40, 138, 137, 136, 40, 40, 42,
-- 42, 42, 42, 42, 42, 42, 42, 56, 56, 56,
-- 56, 62, 132, 62, 64, 131, 130, 64, 129, 64,
-- 64, 65, 128, 158, 65, 65, 65, 65, 71, 127,
-- 71, 71, 74, 74, 74, 74, 74, 74, 74, 74,
--
-- 76, 76, 76, 76, 76, 76, 76, 76, 89, 126,
-- 89, 90, 125, 90, 90, 124, 90, 90, 119, 119,
-- 119, 119, 119, 119, 119, 119, 145, 145, 145, 145,
-- 145, 145, 145, 145, 123, 122, 59, 59, 118, 117,
-- 116, 115, 114, 113, 45, 112, 108, 111, 109, 106,
-- 105, 104, 46, 103, 91, 87, 102, 101, 100, 98,
-- 97, 96, 95, 94, 93, 77, 75, 91, 88, 87,
-- 86, 57, 85, 84, 57, 82, 81, 78, 77, 75,
-- 72, 158, 58, 57, 53, 35, 158, 31, 23, 23,
-- 9, 158, 158, 158, 158, 158, 158, 158, 158, 158,
--
-- 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-- 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-- 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-- 158, 158, 158, 158, 158, 158, 158
-+ 21, 21, 21, 21, 10, 22, 10, 24, 25, 25,
-+ 25, 32, 33, 33, 164, 26, 34, 34, 34, 52,
-+ 53, 27, 26, 26, 26, 26, 10, 11, 12, 11,
-+ 13, 14, 28, 15, 16, 28, 28, 28, 24, 28,
-+ 28, 28, 10, 18, 19, 20, 29, 29, 29, 29,
-+ 29, 30, 10, 29, 29, 29, 29, 29, 29, 29,
-+
-+ 29, 29, 29, 29, 29, 29, 29, 29, 29, 29,
-+ 10, 22, 10, 23, 34, 34, 34, 37, 39, 43,
-+ 32, 33, 33, 45, 55, 56, 46, 60, 43, 45,
-+ 65, 163, 46, 65, 65, 65, 44, 38, 60, 74,
-+ 58, 47, 141, 48, 142, 44, 49, 47, 50, 48,
-+ 76, 51, 62, 94, 50, 41, 44, 51, 37, 61,
-+ 64, 64, 64, 58, 34, 34, 34, 64, 162, 80,
-+ 67, 68, 68, 68, 64, 64, 64, 64, 38, 81,
-+ 69, 70, 71, 68, 68, 68, 60, 161, 43, 69,
-+ 70, 65, 69, 70, 65, 65, 65, 125, 85, 85,
-+
-+ 85, 58, 68, 68, 68, 44, 102, 110, 125, 133,
-+ 102, 69, 70, 111, 114, 160, 159, 126, 85, 85,
-+ 85, 140, 140, 140, 140, 140, 140, 153, 126, 147,
-+ 147, 147, 153, 148, 147, 147, 147, 158, 148, 165,
-+ 157, 156, 155, 151, 150, 149, 146, 154, 145, 144,
-+ 143, 139, 154, 36, 36, 36, 36, 36, 36, 36,
-+ 36, 40, 138, 137, 136, 40, 40, 42, 42, 42,
-+ 42, 42, 42, 42, 42, 57, 57, 57, 57, 63,
-+ 135, 63, 65, 134, 165, 65, 133, 65, 65, 66,
-+ 132, 131, 66, 66, 66, 66, 72, 130, 72, 72,
-+
-+ 75, 75, 75, 75, 75, 75, 75, 75, 77, 77,
-+ 77, 77, 77, 77, 77, 77, 91, 129, 91, 92,
-+ 128, 92, 92, 127, 92, 92, 124, 124, 124, 124,
-+ 124, 124, 124, 124, 152, 152, 152, 152, 152, 152,
-+ 152, 152, 60, 60, 123, 122, 121, 120, 119, 118,
-+ 117, 45, 116, 111, 115, 113, 112, 109, 108, 107,
-+ 46, 106, 93, 89, 105, 104, 103, 101, 100, 99,
-+ 98, 97, 96, 95, 78, 76, 93, 90, 89, 88,
-+ 58, 87, 86, 58, 84, 83, 82, 79, 78, 76,
-+ 73, 165, 59, 58, 54, 35, 165, 31, 23, 23,
-+
-+ 9, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 165, 165
- } ;
-
--static yyconst flex_int16_t yy_chk[438] =
-+static yyconst flex_int16_t yy_chk[449] =
- { 0,
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
- 1, 1, 1, 1, 1, 1, 1, 1, 1, 1,
-- 1, 1, 1, 1, 1, 1, 3, 3, 3, 3,
-- 7, 7, 7, 156, 3, 11, 11, 11, 18, 18,
-- 3, 3, 3, 3, 3, 5, 5, 5, 5, 5,
-+ 1, 1, 1, 1, 1, 1, 1, 3, 3, 3,
-+ 3, 7, 7, 7, 163, 3, 11, 11, 11, 18,
-+ 18, 3, 3, 3, 3, 3, 5, 5, 5, 5,
- 5, 5, 5, 5, 5, 5, 5, 5, 5, 5,
- 5, 5, 5, 5, 5, 5, 5, 5, 5, 5,
- 5, 5, 5, 5, 5, 5, 5, 5, 5, 5,
-
- 5, 5, 5, 5, 5, 5, 5, 5, 5, 5,
-- 5, 8, 12, 12, 12, 14, 15, 16, 8, 8,
-- 8, 17, 20, 20, 17, 23, 24, 29, 155, 24,
-- 29, 29, 29, 48, 16, 14, 31, 29, 128, 17,
-- 128, 17, 48, 17, 24, 17, 24, 99, 24, 42,
-- 24, 99, 15, 33, 33, 33, 23, 26, 26, 26,
-- 26, 154, 33, 33, 26, 36, 42, 31, 32, 32,
-- 32, 26, 26, 26, 26, 44, 59, 32, 32, 32,
-- 34, 34, 34, 73, 75, 36, 153, 75, 59, 59,
-- 59, 65, 44, 110, 65, 65, 65, 67, 67, 67,
--
-- 73, 65, 83, 89, 89, 97, 67, 67, 119, 127,
-- 97, 150, 149, 110, 83, 83, 83, 133, 133, 133,
-- 141, 127, 127, 127, 145, 136, 136, 136, 119, 136,
-- 140, 140, 140, 148, 140, 147, 144, 143, 142, 139,
-- 141, 138, 137, 135, 145, 159, 159, 159, 159, 159,
-- 159, 159, 159, 160, 134, 132, 131, 160, 160, 161,
-- 161, 161, 161, 161, 161, 161, 161, 162, 162, 162,
-- 162, 163, 126, 163, 164, 125, 124, 164, 123, 164,
-- 164, 165, 122, 121, 165, 165, 165, 165, 166, 120,
-- 166, 166, 167, 167, 167, 167, 167, 167, 167, 167,
--
-- 168, 168, 168, 168, 168, 168, 168, 168, 169, 118,
-- 169, 170, 117, 170, 170, 116, 170, 170, 171, 171,
-- 171, 171, 171, 171, 171, 171, 172, 172, 172, 172,
-- 172, 172, 172, 172, 115, 114, 112, 111, 109, 108,
-- 107, 106, 105, 104, 103, 102, 101, 100, 98, 96,
-- 95, 94, 93, 92, 90, 88, 86, 85, 84, 82,
-- 81, 80, 79, 78, 77, 76, 74, 72, 69, 68,
-- 66, 63, 61, 60, 56, 50, 49, 47, 46, 45,
-+ 5, 5, 5, 8, 12, 12, 12, 14, 15, 16,
-+ 8, 8, 8, 17, 20, 20, 17, 23, 42, 24,
-+ 29, 162, 24, 29, 29, 29, 16, 14, 31, 44,
-+ 29, 17, 134, 17, 134, 42, 17, 24, 17, 24,
-+ 76, 17, 24, 76, 24, 15, 44, 24, 36, 23,
-+ 26, 26, 26, 26, 34, 34, 34, 26, 161, 48,
-+ 31, 32, 32, 32, 26, 26, 26, 26, 36, 48,
-+ 32, 32, 32, 33, 33, 33, 60, 160, 74, 91,
-+ 91, 66, 33, 33, 66, 66, 66, 114, 60, 60,
-+
-+ 60, 66, 68, 68, 68, 74, 85, 99, 124, 133,
-+ 102, 68, 68, 99, 102, 157, 156, 114, 85, 85,
-+ 85, 133, 133, 133, 140, 140, 140, 148, 124, 143,
-+ 143, 143, 152, 143, 147, 147, 147, 155, 147, 154,
-+ 151, 150, 149, 146, 145, 144, 142, 148, 141, 138,
-+ 137, 132, 152, 166, 166, 166, 166, 166, 166, 166,
-+ 166, 167, 131, 130, 129, 167, 167, 168, 168, 168,
-+ 168, 168, 168, 168, 168, 169, 169, 169, 169, 170,
-+ 128, 170, 171, 127, 126, 171, 125, 171, 171, 172,
-+ 123, 122, 172, 172, 172, 172, 173, 121, 173, 173,
-+
-+ 174, 174, 174, 174, 174, 174, 174, 174, 175, 175,
-+ 175, 175, 175, 175, 175, 175, 176, 120, 176, 177,
-+ 119, 177, 177, 118, 177, 177, 178, 178, 178, 178,
-+ 178, 178, 178, 178, 179, 179, 179, 179, 179, 179,
-+ 179, 179, 116, 115, 113, 112, 111, 110, 109, 108,
-+ 107, 106, 105, 104, 103, 101, 100, 98, 97, 96,
-+ 95, 94, 92, 90, 88, 87, 86, 84, 83, 82,
-+ 81, 80, 79, 78, 77, 75, 73, 70, 69, 67,
-+ 64, 62, 61, 57, 51, 50, 49, 47, 46, 45,
- 41, 38, 22, 21, 19, 13, 9, 6, 4, 2,
-- 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-
-- 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-- 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-- 158, 158, 158, 158, 158, 158, 158, 158, 158, 158,
-- 158, 158, 158, 158, 158, 158, 158
-+ 165, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 165, 165, 165, 165,
-+ 165, 165, 165, 165, 165, 165, 165, 165
- } ;
-
- static yy_state_type yy_last_accepting_state;
-@@ -662,7 +664,7 @@ static int dts_version = 1;
- static void push_input_file(const char *filename);
- static bool pop_input_file(void);
- static void lexical_error(const char *fmt, ...);
--#line 666 "dtc-lexer.lex.c"
-+#line 668 "dtc-lexer.lex.c"
-
- #define INITIAL 0
- #define BYTESTRING 1
-@@ -704,7 +706,7 @@ FILE *yyget_out (void );
-
- void yyset_out (FILE * out_str );
-
--yy_size_t yyget_leng (void );
-+int yyget_leng (void );
-
- char *yyget_text (void );
-
-@@ -853,6 +855,10 @@ YY_DECL
- register char *yy_cp, *yy_bp;
- register int yy_act;
-
-+#line 68 "dtc-lexer.l"
-+
-+#line 861 "dtc-lexer.lex.c"
-+
- if ( !(yy_init) )
- {
- (yy_init) = 1;
-@@ -879,11 +885,6 @@ YY_DECL
- yy_load_buffer_state( );
- }
-
-- {
--#line 68 "dtc-lexer.l"
--
--#line 886 "dtc-lexer.lex.c"
--
- while ( 1 ) /* loops until end-of-file is reached */
- {
- yy_cp = (yy_c_buf_p);
-@@ -901,7 +902,7 @@ YY_DECL
- yy_match:
- do
- {
-- register YY_CHAR yy_c = yy_ec[YY_SC_TO_UI(*yy_cp)] ;
-+ register YY_CHAR yy_c = yy_ec[YY_SC_TO_UI(*yy_cp)];
- if ( yy_accept[yy_current_state] )
- {
- (yy_last_accepting_state) = yy_current_state;
-@@ -910,13 +911,13 @@ yy_match:
- while ( yy_chk[yy_base[yy_current_state] + yy_c] != yy_current_state )
- {
- yy_current_state = (int) yy_def[yy_current_state];
-- if ( yy_current_state >= 159 )
-+ if ( yy_current_state >= 166 )
- yy_c = yy_meta[(unsigned int) yy_c];
- }
- yy_current_state = yy_nxt[yy_base[yy_current_state] + (unsigned int) yy_c];
- ++yy_cp;
- }
-- while ( yy_current_state != 158 );
-+ while ( yy_current_state != 165 );
- yy_cp = (yy_last_accepting_cpos);
- yy_current_state = (yy_last_accepting_state);
-
-@@ -1007,23 +1008,31 @@ case 5:
- YY_RULE_SETUP
- #line 116 "dtc-lexer.l"
- {
-+ DPRINT("Keyword: /plugin/\n");
-+ return DT_PLUGIN;
-+ }
-+ YY_BREAK
-+case 6:
-+YY_RULE_SETUP
-+#line 121 "dtc-lexer.l"
-+{
- DPRINT("Keyword: /memreserve/\n");
- BEGIN_DEFAULT();
- return DT_MEMRESERVE;
- }
- YY_BREAK
--case 6:
-+case 7:
- YY_RULE_SETUP
--#line 122 "dtc-lexer.l"
-+#line 127 "dtc-lexer.l"
- {
- DPRINT("Keyword: /bits/\n");
- BEGIN_DEFAULT();
- return DT_BITS;
- }
- YY_BREAK
--case 7:
-+case 8:
- YY_RULE_SETUP
--#line 128 "dtc-lexer.l"
-+#line 133 "dtc-lexer.l"
- {
- DPRINT("Keyword: /delete-property/\n");
- DPRINT("<PROPNODENAME>\n");
-@@ -1031,9 +1040,9 @@ YY_RULE_SETUP
- return DT_DEL_PROP;
- }
- YY_BREAK
--case 8:
-+case 9:
- YY_RULE_SETUP
--#line 135 "dtc-lexer.l"
-+#line 140 "dtc-lexer.l"
- {
- DPRINT("Keyword: /delete-node/\n");
- DPRINT("<PROPNODENAME>\n");
-@@ -1041,9 +1050,9 @@ YY_RULE_SETUP
- return DT_DEL_NODE;
- }
- YY_BREAK
--case 9:
-+case 10:
- YY_RULE_SETUP
--#line 142 "dtc-lexer.l"
-+#line 147 "dtc-lexer.l"
- {
- DPRINT("Label: %s\n", yytext);
- yylval.labelref = xstrdup(yytext);
-@@ -1051,9 +1060,9 @@ YY_RULE_SETUP
- return DT_LABEL;
- }
- YY_BREAK
--case 10:
-+case 11:
- YY_RULE_SETUP
--#line 149 "dtc-lexer.l"
-+#line 154 "dtc-lexer.l"
- {
- char *e;
- DPRINT("Integer Literal: '%s'\n", yytext);
-@@ -1073,10 +1082,10 @@ YY_RULE_SETUP
- return DT_LITERAL;
- }
- YY_BREAK
--case 11:
--/* rule 11 can match eol */
-+case 12:
-+/* rule 12 can match eol */
- YY_RULE_SETUP
--#line 168 "dtc-lexer.l"
-+#line 173 "dtc-lexer.l"
- {
- struct data d;
- DPRINT("Character literal: %s\n", yytext);
-@@ -1098,18 +1107,18 @@ YY_RULE_SETUP
- return DT_CHAR_LITERAL;
- }
- YY_BREAK
--case 12:
-+case 13:
- YY_RULE_SETUP
--#line 189 "dtc-lexer.l"
-+#line 194 "dtc-lexer.l"
- { /* label reference */
- DPRINT("Ref: %s\n", yytext+1);
- yylval.labelref = xstrdup(yytext+1);
- return DT_REF;
- }
- YY_BREAK
--case 13:
-+case 14:
- YY_RULE_SETUP
--#line 195 "dtc-lexer.l"
-+#line 200 "dtc-lexer.l"
- { /* new-style path reference */
- yytext[yyleng-1] = '\0';
- DPRINT("Ref: %s\n", yytext+2);
-@@ -1117,27 +1126,27 @@ YY_RULE_SETUP
- return DT_REF;
- }
- YY_BREAK
--case 14:
-+case 15:
- YY_RULE_SETUP
--#line 202 "dtc-lexer.l"
-+#line 207 "dtc-lexer.l"
- {
- yylval.byte = strtol(yytext, NULL, 16);
- DPRINT("Byte: %02x\n", (int)yylval.byte);
- return DT_BYTE;
- }
- YY_BREAK
--case 15:
-+case 16:
- YY_RULE_SETUP
--#line 208 "dtc-lexer.l"
-+#line 213 "dtc-lexer.l"
- {
- DPRINT("/BYTESTRING\n");
- BEGIN_DEFAULT();
- return ']';
- }
- YY_BREAK
--case 16:
-+case 17:
- YY_RULE_SETUP
--#line 214 "dtc-lexer.l"
-+#line 219 "dtc-lexer.l"
- {
- DPRINT("PropNodeName: %s\n", yytext);
- yylval.propnodename = xstrdup((yytext[0] == '\\') ?
-@@ -1146,75 +1155,75 @@ YY_RULE_SETUP
- return DT_PROPNODENAME;
- }
- YY_BREAK
--case 17:
-+case 18:
- YY_RULE_SETUP
--#line 222 "dtc-lexer.l"
-+#line 227 "dtc-lexer.l"
- {
- DPRINT("Binary Include\n");
- return DT_INCBIN;
- }
- YY_BREAK
--case 18:
--/* rule 18 can match eol */
--YY_RULE_SETUP
--#line 227 "dtc-lexer.l"
--/* eat whitespace */
-- YY_BREAK
- case 19:
- /* rule 19 can match eol */
- YY_RULE_SETUP
--#line 228 "dtc-lexer.l"
--/* eat C-style comments */
-+#line 232 "dtc-lexer.l"
-+/* eat whitespace */
- YY_BREAK
- case 20:
- /* rule 20 can match eol */
- YY_RULE_SETUP
--#line 229 "dtc-lexer.l"
--/* eat C++-style comments */
-+#line 233 "dtc-lexer.l"
-+/* eat C-style comments */
- YY_BREAK
- case 21:
-+/* rule 21 can match eol */
- YY_RULE_SETUP
--#line 231 "dtc-lexer.l"
--{ return DT_LSHIFT; };
-+#line 234 "dtc-lexer.l"
-+/* eat C++-style comments */
- YY_BREAK
- case 22:
- YY_RULE_SETUP
--#line 232 "dtc-lexer.l"
--{ return DT_RSHIFT; };
-+#line 236 "dtc-lexer.l"
-+{ return DT_LSHIFT; };
- YY_BREAK
- case 23:
- YY_RULE_SETUP
--#line 233 "dtc-lexer.l"
--{ return DT_LE; };
-+#line 237 "dtc-lexer.l"
-+{ return DT_RSHIFT; };
- YY_BREAK
- case 24:
- YY_RULE_SETUP
--#line 234 "dtc-lexer.l"
--{ return DT_GE; };
-+#line 238 "dtc-lexer.l"
-+{ return DT_LE; };
- YY_BREAK
- case 25:
- YY_RULE_SETUP
--#line 235 "dtc-lexer.l"
--{ return DT_EQ; };
-+#line 239 "dtc-lexer.l"
-+{ return DT_GE; };
- YY_BREAK
- case 26:
- YY_RULE_SETUP
--#line 236 "dtc-lexer.l"
--{ return DT_NE; };
-+#line 240 "dtc-lexer.l"
-+{ return DT_EQ; };
- YY_BREAK
- case 27:
- YY_RULE_SETUP
--#line 237 "dtc-lexer.l"
--{ return DT_AND; };
-+#line 241 "dtc-lexer.l"
-+{ return DT_NE; };
- YY_BREAK
- case 28:
- YY_RULE_SETUP
--#line 238 "dtc-lexer.l"
--{ return DT_OR; };
-+#line 242 "dtc-lexer.l"
-+{ return DT_AND; };
- YY_BREAK
- case 29:
- YY_RULE_SETUP
--#line 240 "dtc-lexer.l"
-+#line 243 "dtc-lexer.l"
-+{ return DT_OR; };
-+ YY_BREAK
-+case 30:
-+YY_RULE_SETUP
-+#line 245 "dtc-lexer.l"
- {
- DPRINT("Char: %c (\\x%02x)\n", yytext[0],
- (unsigned)yytext[0]);
-@@ -1230,12 +1239,12 @@ YY_RULE_SETUP
- return yytext[0];
- }
- YY_BREAK
--case 30:
-+case 31:
- YY_RULE_SETUP
--#line 255 "dtc-lexer.l"
-+#line 260 "dtc-lexer.l"
- ECHO;
- YY_BREAK
--#line 1239 "dtc-lexer.lex.c"
-+#line 1248 "dtc-lexer.lex.c"
-
- case YY_END_OF_BUFFER:
- {
-@@ -1365,7 +1374,6 @@ ECHO;
- "fatal flex scanner internal error--no action found" );
- } /* end of action switch */
- } /* end of scanning one token */
-- } /* end of user's declarations */
- } /* end of yylex */
-
- /* yy_get_next_buffer - try to read in a new buffer
-@@ -1421,21 +1429,21 @@ static int yy_get_next_buffer (void)
-
- else
- {
-- yy_size_t num_to_read =
-+ int num_to_read =
- YY_CURRENT_BUFFER_LVALUE->yy_buf_size - number_to_move - 1;
-
- while ( num_to_read <= 0 )
- { /* Not enough room in the buffer - grow it. */
-
- /* just a shorter name for the current buffer */
-- YY_BUFFER_STATE b = YY_CURRENT_BUFFER_LVALUE;
-+ YY_BUFFER_STATE b = YY_CURRENT_BUFFER;
-
- int yy_c_buf_p_offset =
- (int) ((yy_c_buf_p) - b->yy_ch_buf);
-
- if ( b->yy_is_our_buffer )
- {
-- yy_size_t new_size = b->yy_buf_size * 2;
-+ int new_size = b->yy_buf_size * 2;
-
- if ( new_size <= 0 )
- b->yy_buf_size += b->yy_buf_size / 8;
-@@ -1466,7 +1474,7 @@ static int yy_get_next_buffer (void)
-
- /* Read in more data. */
- YY_INPUT( (&YY_CURRENT_BUFFER_LVALUE->yy_ch_buf[number_to_move]),
-- (yy_n_chars), num_to_read );
-+ (yy_n_chars), (size_t) num_to_read );
-
- YY_CURRENT_BUFFER_LVALUE->yy_n_chars = (yy_n_chars);
- }
-@@ -1528,7 +1536,7 @@ static int yy_get_next_buffer (void)
- while ( yy_chk[yy_base[yy_current_state] + yy_c] != yy_current_state )
- {
- yy_current_state = (int) yy_def[yy_current_state];
-- if ( yy_current_state >= 159 )
-+ if ( yy_current_state >= 166 )
- yy_c = yy_meta[(unsigned int) yy_c];
- }
- yy_current_state = yy_nxt[yy_base[yy_current_state] + (unsigned int) yy_c];
-@@ -1556,13 +1564,13 @@ static int yy_get_next_buffer (void)
- while ( yy_chk[yy_base[yy_current_state] + yy_c] != yy_current_state )
- {
- yy_current_state = (int) yy_def[yy_current_state];
-- if ( yy_current_state >= 159 )
-+ if ( yy_current_state >= 166 )
- yy_c = yy_meta[(unsigned int) yy_c];
- }
- yy_current_state = yy_nxt[yy_base[yy_current_state] + (unsigned int) yy_c];
-- yy_is_jam = (yy_current_state == 158);
-+ yy_is_jam = (yy_current_state == 165);
-
-- return yy_is_jam ? 0 : yy_current_state;
-+ return yy_is_jam ? 0 : yy_current_state;
- }
-
- #ifndef YY_NO_INPUT
-@@ -1589,7 +1597,7 @@ static int yy_get_next_buffer (void)
-
- else
- { /* need more input */
-- yy_size_t offset = (yy_c_buf_p) - (yytext_ptr);
-+ int offset = (yy_c_buf_p) - (yytext_ptr);
- ++(yy_c_buf_p);
-
- switch ( yy_get_next_buffer( ) )
-@@ -1863,7 +1871,7 @@ void yypop_buffer_state (void)
- */
- static void yyensure_buffer_stack (void)
- {
-- yy_size_t num_to_alloc;
-+ int num_to_alloc;
-
- if (!(yy_buffer_stack)) {
-
-@@ -1960,12 +1968,12 @@ YY_BUFFER_STATE yy_scan_string (yyconst
- *
- * @return the newly allocated buffer state object.
- */
--YY_BUFFER_STATE yy_scan_bytes (yyconst char * yybytes, yy_size_t _yybytes_len )
-+YY_BUFFER_STATE yy_scan_bytes (yyconst char * yybytes, int _yybytes_len )
- {
- YY_BUFFER_STATE b;
- char *buf;
- yy_size_t n;
-- yy_size_t i;
-+ int i;
-
- /* Get memory for full buffer, including space for trailing EOB's. */
- n = _yybytes_len + 2;
-@@ -2047,7 +2055,7 @@ FILE *yyget_out (void)
- /** Get the length of the current token.
- *
- */
--yy_size_t yyget_leng (void)
-+int yyget_leng (void)
- {
- return yyleng;
- }
-@@ -2195,7 +2203,7 @@ void yyfree (void * ptr )
-
- #define YYTABLES_NAME "yytables"
-
--#line 254 "dtc-lexer.l"
-+#line 260 "dtc-lexer.l"
-
-
-
---- a/scripts/dtc/dtc-parser.tab.c_shipped
-+++ b/scripts/dtc/dtc-parser.tab.c_shipped
-@@ -65,6 +65,7 @@
- #line 20 "dtc-parser.y" /* yacc.c:339 */
-
- #include <stdio.h>
-+#include <inttypes.h>
-
- #include "dtc.h"
- #include "srcpos.h"
-@@ -80,7 +81,7 @@ extern void yyerror(char const *s);
- extern struct boot_info *the_boot_info;
- extern bool treesource_error;
-
--#line 84 "dtc-parser.tab.c" /* yacc.c:339 */
-+#line 85 "dtc-parser.tab.c" /* yacc.c:339 */
-
- # ifndef YY_NULLPTR
- # if defined __cplusplus && 201103L <= __cplusplus
-@@ -116,26 +117,27 @@ extern int yydebug;
- enum yytokentype
- {
- DT_V1 = 258,
-- DT_MEMRESERVE = 259,
-- DT_LSHIFT = 260,
-- DT_RSHIFT = 261,
-- DT_LE = 262,
-- DT_GE = 263,
-- DT_EQ = 264,
-- DT_NE = 265,
-- DT_AND = 266,
-- DT_OR = 267,
-- DT_BITS = 268,
-- DT_DEL_PROP = 269,
-- DT_DEL_NODE = 270,
-- DT_PROPNODENAME = 271,
-- DT_LITERAL = 272,
-- DT_CHAR_LITERAL = 273,
-- DT_BYTE = 274,
-- DT_STRING = 275,
-- DT_LABEL = 276,
-- DT_REF = 277,
-- DT_INCBIN = 278
-+ DT_PLUGIN = 259,
-+ DT_MEMRESERVE = 260,
-+ DT_LSHIFT = 261,
-+ DT_RSHIFT = 262,
-+ DT_LE = 263,
-+ DT_GE = 264,
-+ DT_EQ = 265,
-+ DT_NE = 266,
-+ DT_AND = 267,
-+ DT_OR = 268,
-+ DT_BITS = 269,
-+ DT_DEL_PROP = 270,
-+ DT_DEL_NODE = 271,
-+ DT_PROPNODENAME = 272,
-+ DT_LITERAL = 273,
-+ DT_CHAR_LITERAL = 274,
-+ DT_BYTE = 275,
-+ DT_STRING = 276,
-+ DT_LABEL = 277,
-+ DT_REF = 278,
-+ DT_INCBIN = 279
- };
- #endif
-
-@@ -144,7 +146,7 @@ extern int yydebug;
- typedef union YYSTYPE YYSTYPE;
- union YYSTYPE
- {
--#line 38 "dtc-parser.y" /* yacc.c:355 */
-+#line 39 "dtc-parser.y" /* yacc.c:355 */
-
- char *propnodename;
- char *labelref;
-@@ -162,8 +164,9 @@ union YYSTYPE
- struct node *nodelist;
- struct reserve_info *re;
- uint64_t integer;
-+ bool is_plugin;
-
--#line 167 "dtc-parser.tab.c" /* yacc.c:355 */
-+#line 170 "dtc-parser.tab.c" /* yacc.c:355 */
- };
- # define YYSTYPE_IS_TRIVIAL 1
- # define YYSTYPE_IS_DECLARED 1
-@@ -192,7 +195,7 @@ int yyparse (void);
-
- /* Copy the second part of user declarations. */
-
--#line 196 "dtc-parser.tab.c" /* yacc.c:358 */
-+#line 199 "dtc-parser.tab.c" /* yacc.c:358 */
-
- #ifdef short
- # undef short
-@@ -439,18 +442,18 @@ union yyalloc
- #define YYLAST 136
-
- /* YYNTOKENS -- Number of terminals. */
--#define YYNTOKENS 47
-+#define YYNTOKENS 48
- /* YYNNTS -- Number of nonterminals. */
--#define YYNNTS 28
-+#define YYNNTS 29
- /* YYNRULES -- Number of rules. */
--#define YYNRULES 80
-+#define YYNRULES 82
- /* YYNSTATES -- Number of states. */
--#define YYNSTATES 144
-+#define YYNSTATES 147
-
- /* YYTRANSLATE[YYX] -- Symbol number corresponding to YYX as returned
- by yylex, with out-of-bounds checking. */
- #define YYUNDEFTOK 2
--#define YYMAXUTOK 278
-+#define YYMAXUTOK 279
-
- #define YYTRANSLATE(YYX) \
- ((unsigned int) (YYX) <= YYMAXUTOK ? yytranslate[YYX] : YYUNDEFTOK)
-@@ -462,16 +465,16 @@ static const yytype_uint8 yytranslate[]
- 0, 2, 2, 2, 2, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
-- 2, 2, 2, 46, 2, 2, 2, 44, 40, 2,
-- 32, 34, 43, 41, 33, 42, 2, 25, 2, 2,
-- 2, 2, 2, 2, 2, 2, 2, 2, 37, 24,
-- 35, 28, 29, 36, 2, 2, 2, 2, 2, 2,
-+ 2, 2, 2, 47, 2, 2, 2, 45, 41, 2,
-+ 33, 35, 44, 42, 34, 43, 2, 26, 2, 2,
-+ 2, 2, 2, 2, 2, 2, 2, 2, 38, 25,
-+ 36, 29, 30, 37, 2, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
-- 2, 30, 2, 31, 39, 2, 2, 2, 2, 2,
-+ 2, 31, 2, 32, 40, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
-- 2, 2, 2, 26, 38, 27, 45, 2, 2, 2,
-+ 2, 2, 2, 27, 39, 28, 46, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
-@@ -486,22 +489,22 @@ static const yytype_uint8 yytranslate[]
- 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
- 2, 2, 2, 2, 2, 2, 1, 2, 3, 4,
- 5, 6, 7, 8, 9, 10, 11, 12, 13, 14,
-- 15, 16, 17, 18, 19, 20, 21, 22, 23
-+ 15, 16, 17, 18, 19, 20, 21, 22, 23, 24
- };
-
- #if YYDEBUG
- /* YYRLINE[YYN] -- Source line where rule number YYN was defined. */
- static const yytype_uint16 yyrline[] =
- {
-- 0, 104, 104, 113, 116, 123, 127, 135, 139, 144,
-- 155, 165, 180, 188, 191, 198, 202, 206, 210, 218,
-- 222, 226, 230, 234, 250, 260, 268, 271, 275, 282,
-- 298, 303, 322, 336, 343, 344, 345, 352, 356, 357,
-- 361, 362, 366, 367, 371, 372, 376, 377, 381, 382,
-- 386, 387, 388, 392, 393, 394, 395, 396, 400, 401,
-- 402, 406, 407, 408, 412, 413, 414, 415, 419, 420,
-- 421, 422, 427, 430, 434, 442, 445, 449, 457, 461,
-- 465
-+ 0, 108, 108, 118, 121, 129, 132, 139, 143, 151,
-+ 155, 160, 171, 181, 196, 204, 207, 214, 218, 222,
-+ 226, 234, 238, 242, 246, 250, 266, 276, 284, 287,
-+ 291, 298, 314, 319, 338, 352, 359, 360, 361, 368,
-+ 372, 373, 377, 378, 382, 383, 387, 388, 392, 393,
-+ 397, 398, 402, 403, 404, 408, 409, 410, 411, 412,
-+ 416, 417, 418, 422, 423, 424, 428, 429, 430, 431,
-+ 435, 436, 437, 438, 443, 446, 450, 458, 461, 465,
-+ 473, 477, 481
- };
- #endif
-
-@@ -510,19 +513,19 @@ static const yytype_uint16 yyrline[] =
- First, the terminals, then, starting at YYNTOKENS, nonterminals. */
- static const char *const yytname[] =
- {
-- "$end", "error", "$undefined", "DT_V1", "DT_MEMRESERVE", "DT_LSHIFT",
-- "DT_RSHIFT", "DT_LE", "DT_GE", "DT_EQ", "DT_NE", "DT_AND", "DT_OR",
-- "DT_BITS", "DT_DEL_PROP", "DT_DEL_NODE", "DT_PROPNODENAME", "DT_LITERAL",
-- "DT_CHAR_LITERAL", "DT_BYTE", "DT_STRING", "DT_LABEL", "DT_REF",
-- "DT_INCBIN", "';'", "'/'", "'{'", "'}'", "'='", "'>'", "'['", "']'",
-- "'('", "','", "')'", "'<'", "'?'", "':'", "'|'", "'^'", "'&'", "'+'",
-- "'-'", "'*'", "'%'", "'~'", "'!'", "$accept", "sourcefile",
-- "memreserves", "memreserve", "devicetree", "nodedef", "proplist",
-- "propdef", "propdata", "propdataprefix", "arrayprefix", "integer_prim",
-- "integer_expr", "integer_trinary", "integer_or", "integer_and",
-- "integer_bitor", "integer_bitxor", "integer_bitand", "integer_eq",
-- "integer_rela", "integer_shift", "integer_add", "integer_mul",
-- "integer_unary", "bytestring", "subnodes", "subnode", YY_NULLPTR
-+ "$end", "error", "$undefined", "DT_V1", "DT_PLUGIN", "DT_MEMRESERVE",
-+ "DT_LSHIFT", "DT_RSHIFT", "DT_LE", "DT_GE", "DT_EQ", "DT_NE", "DT_AND",
-+ "DT_OR", "DT_BITS", "DT_DEL_PROP", "DT_DEL_NODE", "DT_PROPNODENAME",
-+ "DT_LITERAL", "DT_CHAR_LITERAL", "DT_BYTE", "DT_STRING", "DT_LABEL",
-+ "DT_REF", "DT_INCBIN", "';'", "'/'", "'{'", "'}'", "'='", "'>'", "'['",
-+ "']'", "'('", "','", "')'", "'<'", "'?'", "':'", "'|'", "'^'", "'&'",
-+ "'+'", "'-'", "'*'", "'%'", "'~'", "'!'", "$accept", "sourcefile",
-+ "plugindecl", "memreserves", "memreserve", "devicetree", "nodedef",
-+ "proplist", "propdef", "propdata", "propdataprefix", "arrayprefix",
-+ "integer_prim", "integer_expr", "integer_trinary", "integer_or",
-+ "integer_and", "integer_bitor", "integer_bitxor", "integer_bitand",
-+ "integer_eq", "integer_rela", "integer_shift", "integer_add",
-+ "integer_mul", "integer_unary", "bytestring", "subnodes", "subnode", YY_NULLPTR
- };
- #endif
-
-@@ -533,16 +536,16 @@ static const yytype_uint16 yytoknum[] =
- {
- 0, 256, 257, 258, 259, 260, 261, 262, 263, 264,
- 265, 266, 267, 268, 269, 270, 271, 272, 273, 274,
-- 275, 276, 277, 278, 59, 47, 123, 125, 61, 62,
-- 91, 93, 40, 44, 41, 60, 63, 58, 124, 94,
-- 38, 43, 45, 42, 37, 126, 33
-+ 275, 276, 277, 278, 279, 59, 47, 123, 125, 61,
-+ 62, 91, 93, 40, 44, 41, 60, 63, 58, 124,
-+ 94, 38, 43, 45, 42, 37, 126, 33
- };
- # endif
-
--#define YYPACT_NINF -81
-+#define YYPACT_NINF -84
-
- #define yypact_value_is_default(Yystate) \
-- (!!((Yystate) == (-81)))
-+ (!!((Yystate) == (-84)))
-
- #define YYTABLE_NINF -1
-
-@@ -553,21 +556,21 @@ static const yytype_uint16 yytoknum[] =
- STATE-NUM. */
- static const yytype_int8 yypact[] =
- {
-- 16, -11, 21, 10, -81, 25, 10, 19, 10, -81,
-- -81, -9, 25, -81, 2, 51, -81, -9, -9, -9,
-- -81, 1, -81, -6, 50, 14, 28, 29, 36, 3,
-- 58, 44, -3, -81, 47, -81, -81, 65, 68, 2,
-- 2, -81, -81, -81, -81, -9, -9, -9, -9, -9,
-- -9, -9, -9, -9, -9, -9, -9, -9, -9, -9,
-- -9, -9, -9, -9, -81, 63, 69, 2, -81, -81,
-- 50, 57, 14, 28, 29, 36, 3, 3, 58, 58,
-- 58, 58, 44, 44, -3, -3, -81, -81, -81, 79,
-- 80, -8, 63, -81, 72, 63, -81, -81, -9, 76,
-- 77, -81, -81, -81, -81, -81, 78, -81, -81, -81,
-- -81, -81, 35, 4, -81, -81, -81, -81, 86, -81,
-- -81, -81, 73, -81, -81, 33, 71, 84, 39, -81,
-- -81, -81, -81, -81, 41, -81, -81, -81, 25, -81,
-- 74, 25, 75, -81
-+ 15, -12, 35, 42, -84, 27, 9, -84, 24, 9,
-+ 43, 9, -84, -84, -10, 24, -84, 60, 44, -84,
-+ -10, -10, -10, -84, 55, -84, -7, 52, 53, 51,
-+ 54, 10, 2, 38, 37, -4, -84, 68, -84, -84,
-+ 71, 73, 60, 60, -84, -84, -84, -84, -10, -10,
-+ -10, -10, -10, -10, -10, -10, -10, -10, -10, -10,
-+ -10, -10, -10, -10, -10, -10, -10, -84, 56, 72,
-+ 60, -84, -84, 52, 61, 53, 51, 54, 10, 2,
-+ 2, 38, 38, 38, 38, 37, 37, -4, -4, -84,
-+ -84, -84, 81, 83, 34, 56, -84, 74, 56, -84,
-+ -84, -10, 76, 78, -84, -84, -84, -84, -84, 79,
-+ -84, -84, -84, -84, -84, -6, 3, -84, -84, -84,
-+ -84, 87, -84, -84, -84, 75, -84, -84, 32, 70,
-+ 86, 36, -84, -84, -84, -84, -84, 47, -84, -84,
-+ -84, 24, -84, 77, 24, 80, -84
- };
-
- /* YYDEFACT[STATE-NUM] -- Default reduction number in state STATE-NUM.
-@@ -575,37 +578,37 @@ static const yytype_int8 yypact[] =
- means the default is an error. */
- static const yytype_uint8 yydefact[] =
- {
-- 0, 0, 0, 3, 1, 0, 0, 0, 3, 34,
-- 35, 0, 0, 6, 0, 2, 4, 0, 0, 0,
-- 68, 0, 37, 38, 40, 42, 44, 46, 48, 50,
-- 53, 60, 63, 67, 0, 13, 7, 0, 0, 0,
-- 0, 69, 70, 71, 36, 0, 0, 0, 0, 0,
-+ 0, 0, 0, 3, 1, 0, 5, 4, 0, 0,
-+ 0, 5, 36, 37, 0, 0, 8, 0, 2, 6,
-+ 0, 0, 0, 70, 0, 39, 40, 42, 44, 46,
-+ 48, 50, 52, 55, 62, 65, 69, 0, 15, 9,
-+ 0, 0, 0, 0, 71, 72, 73, 38, 0, 0,
- 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
-- 0, 0, 0, 0, 5, 75, 0, 0, 10, 8,
-- 41, 0, 43, 45, 47, 49, 51, 52, 56, 57,
-- 55, 54, 58, 59, 61, 62, 65, 64, 66, 0,
-- 0, 0, 0, 14, 0, 75, 11, 9, 0, 0,
-- 0, 16, 26, 78, 18, 80, 0, 77, 76, 39,
-- 17, 79, 0, 0, 12, 25, 15, 27, 0, 19,
-- 28, 22, 0, 72, 30, 0, 0, 0, 0, 33,
-- 32, 20, 31, 29, 0, 73, 74, 21, 0, 24,
-- 0, 0, 0, 23
-+ 0, 0, 0, 0, 0, 0, 0, 7, 77, 0,
-+ 0, 12, 10, 43, 0, 45, 47, 49, 51, 53,
-+ 54, 58, 59, 57, 56, 60, 61, 63, 64, 67,
-+ 66, 68, 0, 0, 0, 0, 16, 0, 77, 13,
-+ 11, 0, 0, 0, 18, 28, 80, 20, 82, 0,
-+ 79, 78, 41, 19, 81, 0, 0, 14, 27, 17,
-+ 29, 0, 21, 30, 24, 0, 74, 32, 0, 0,
-+ 0, 0, 35, 34, 22, 33, 31, 0, 75, 76,
-+ 23, 0, 26, 0, 0, 0, 25
- };
-
- /* YYPGOTO[NTERM-NUM]. */
- static const yytype_int8 yypgoto[] =
- {
-- -81, -81, 100, 104, -81, -38, -81, -80, -81, -81,
-- -81, -5, 66, 13, -81, 70, 67, 81, 64, 82,
-- 37, 27, 34, 38, -14, -81, 22, 24
-+ -84, -84, -84, 98, 101, -84, -41, -84, -83, -84,
-+ -84, -84, -8, 63, 12, -84, 66, 67, 65, 69,
-+ 82, 29, 18, 25, 26, -17, -84, 20, 28
- };
-
- /* YYDEFGOTO[NTERM-NUM]. */
- static const yytype_int16 yydefgoto[] =
- {
-- -1, 2, 7, 8, 15, 36, 65, 93, 112, 113,
-- 125, 20, 21, 22, 23, 24, 25, 26, 27, 28,
-- 29, 30, 31, 32, 33, 128, 94, 95
-+ -1, 2, 6, 10, 11, 18, 39, 68, 96, 115,
-+ 116, 128, 23, 24, 25, 26, 27, 28, 29, 30,
-+ 31, 32, 33, 34, 35, 36, 131, 97, 98
- };
-
- /* YYTABLE[YYPACT[STATE-NUM]] -- What to do in state STATE-NUM. If
-@@ -613,87 +616,87 @@ static const yytype_int16 yydefgoto[] =
- number is the opposite. If YYTABLE_NINF, syntax error. */
- static const yytype_uint8 yytable[] =
- {
-- 12, 68, 69, 41, 42, 43, 45, 34, 9, 10,
-- 53, 54, 104, 3, 5, 107, 101, 118, 35, 1,
-- 102, 4, 61, 11, 119, 120, 121, 122, 35, 97,
-- 46, 6, 55, 17, 123, 44, 18, 19, 56, 124,
-- 62, 63, 9, 10, 14, 51, 52, 86, 87, 88,
-- 9, 10, 48, 103, 129, 130, 115, 11, 135, 116,
-- 136, 47, 131, 57, 58, 11, 37, 49, 117, 50,
-- 137, 64, 38, 39, 138, 139, 40, 89, 90, 91,
-- 78, 79, 80, 81, 92, 59, 60, 66, 76, 77,
-- 67, 82, 83, 96, 98, 99, 100, 84, 85, 106,
-- 110, 111, 114, 126, 134, 127, 133, 141, 16, 143,
-- 13, 109, 71, 74, 72, 70, 105, 108, 0, 0,
-- 132, 0, 0, 0, 0, 0, 0, 0, 0, 73,
-- 0, 0, 75, 140, 0, 0, 142
-+ 15, 71, 72, 44, 45, 46, 48, 37, 12, 13,
-+ 56, 57, 107, 3, 8, 110, 118, 121, 1, 119,
-+ 54, 55, 64, 14, 122, 123, 124, 125, 120, 100,
-+ 49, 9, 58, 20, 126, 4, 21, 22, 59, 127,
-+ 65, 66, 12, 13, 60, 61, 5, 89, 90, 91,
-+ 12, 13, 7, 106, 132, 133, 138, 14, 139, 104,
-+ 40, 38, 134, 105, 50, 14, 41, 42, 140, 17,
-+ 43, 92, 93, 94, 81, 82, 83, 84, 95, 62,
-+ 63, 141, 142, 79, 80, 85, 86, 38, 87, 88,
-+ 47, 52, 51, 67, 69, 53, 70, 99, 102, 101,
-+ 103, 113, 109, 114, 117, 129, 136, 137, 130, 19,
-+ 16, 144, 74, 112, 73, 146, 76, 75, 111, 0,
-+ 135, 77, 0, 108, 0, 0, 0, 0, 0, 0,
-+ 0, 0, 0, 143, 0, 78, 145
- };
-
- static const yytype_int16 yycheck[] =
- {
-- 5, 39, 40, 17, 18, 19, 12, 12, 17, 18,
-- 7, 8, 92, 24, 4, 95, 24, 13, 26, 3,
-- 28, 0, 25, 32, 20, 21, 22, 23, 26, 67,
-- 36, 21, 29, 42, 30, 34, 45, 46, 35, 35,
-- 43, 44, 17, 18, 25, 9, 10, 61, 62, 63,
-- 17, 18, 38, 91, 21, 22, 21, 32, 19, 24,
-- 21, 11, 29, 5, 6, 32, 15, 39, 33, 40,
-- 31, 24, 21, 22, 33, 34, 25, 14, 15, 16,
-- 53, 54, 55, 56, 21, 41, 42, 22, 51, 52,
-- 22, 57, 58, 24, 37, 16, 16, 59, 60, 27,
-- 24, 24, 24, 17, 20, 32, 35, 33, 8, 34,
-- 6, 98, 46, 49, 47, 45, 92, 95, -1, -1,
-- 125, -1, -1, -1, -1, -1, -1, -1, -1, 48,
-- -1, -1, 50, 138, -1, -1, 141
-+ 8, 42, 43, 20, 21, 22, 13, 15, 18, 19,
-+ 8, 9, 95, 25, 5, 98, 22, 14, 3, 25,
-+ 10, 11, 26, 33, 21, 22, 23, 24, 34, 70,
-+ 37, 22, 30, 43, 31, 0, 46, 47, 36, 36,
-+ 44, 45, 18, 19, 6, 7, 4, 64, 65, 66,
-+ 18, 19, 25, 94, 22, 23, 20, 33, 22, 25,
-+ 16, 27, 30, 29, 12, 33, 22, 23, 32, 26,
-+ 26, 15, 16, 17, 56, 57, 58, 59, 22, 42,
-+ 43, 34, 35, 54, 55, 60, 61, 27, 62, 63,
-+ 35, 40, 39, 25, 23, 41, 23, 25, 17, 38,
-+ 17, 25, 28, 25, 25, 18, 36, 21, 33, 11,
-+ 9, 34, 49, 101, 48, 35, 51, 50, 98, -1,
-+ 128, 52, -1, 95, -1, -1, -1, -1, -1, -1,
-+ -1, -1, -1, 141, -1, 53, 144
- };
-
- /* YYSTOS[STATE-NUM] -- The (internal number of the) accessing
- symbol of state STATE-NUM. */
- static const yytype_uint8 yystos[] =
- {
-- 0, 3, 48, 24, 0, 4, 21, 49, 50, 17,
-- 18, 32, 58, 50, 25, 51, 49, 42, 45, 46,
-- 58, 59, 60, 61, 62, 63, 64, 65, 66, 67,
-- 68, 69, 70, 71, 58, 26, 52, 15, 21, 22,
-- 25, 71, 71, 71, 34, 12, 36, 11, 38, 39,
-- 40, 9, 10, 7, 8, 29, 35, 5, 6, 41,
-- 42, 25, 43, 44, 24, 53, 22, 22, 52, 52,
-- 62, 59, 63, 64, 65, 66, 67, 67, 68, 68,
-- 68, 68, 69, 69, 70, 70, 71, 71, 71, 14,
-- 15, 16, 21, 54, 73, 74, 24, 52, 37, 16,
-- 16, 24, 28, 52, 54, 74, 27, 54, 73, 60,
-- 24, 24, 55, 56, 24, 21, 24, 33, 13, 20,
-- 21, 22, 23, 30, 35, 57, 17, 32, 72, 21,
-- 22, 29, 58, 35, 20, 19, 21, 31, 33, 34,
-- 58, 33, 58, 34
-+ 0, 3, 49, 25, 0, 4, 50, 25, 5, 22,
-+ 51, 52, 18, 19, 33, 60, 52, 26, 53, 51,
-+ 43, 46, 47, 60, 61, 62, 63, 64, 65, 66,
-+ 67, 68, 69, 70, 71, 72, 73, 60, 27, 54,
-+ 16, 22, 23, 26, 73, 73, 73, 35, 13, 37,
-+ 12, 39, 40, 41, 10, 11, 8, 9, 30, 36,
-+ 6, 7, 42, 43, 26, 44, 45, 25, 55, 23,
-+ 23, 54, 54, 64, 61, 65, 66, 67, 68, 69,
-+ 69, 70, 70, 70, 70, 71, 71, 72, 72, 73,
-+ 73, 73, 15, 16, 17, 22, 56, 75, 76, 25,
-+ 54, 38, 17, 17, 25, 29, 54, 56, 76, 28,
-+ 56, 75, 62, 25, 25, 57, 58, 25, 22, 25,
-+ 34, 14, 21, 22, 23, 24, 31, 36, 59, 18,
-+ 33, 74, 22, 23, 30, 60, 36, 21, 20, 22,
-+ 32, 34, 35, 60, 34, 60, 35
- };
-
- /* YYR1[YYN] -- Symbol number of symbol that rule YYN derives. */
- static const yytype_uint8 yyr1[] =
- {
-- 0, 47, 48, 49, 49, 50, 50, 51, 51, 51,
-- 51, 51, 52, 53, 53, 54, 54, 54, 54, 55,
-- 55, 55, 55, 55, 55, 55, 56, 56, 56, 57,
-- 57, 57, 57, 57, 58, 58, 58, 59, 60, 60,
-- 61, 61, 62, 62, 63, 63, 64, 64, 65, 65,
-- 66, 66, 66, 67, 67, 67, 67, 67, 68, 68,
-- 68, 69, 69, 69, 70, 70, 70, 70, 71, 71,
-- 71, 71, 72, 72, 72, 73, 73, 73, 74, 74,
-- 74
-+ 0, 48, 49, 50, 50, 51, 51, 52, 52, 53,
-+ 53, 53, 53, 53, 54, 55, 55, 56, 56, 56,
-+ 56, 57, 57, 57, 57, 57, 57, 57, 58, 58,
-+ 58, 59, 59, 59, 59, 59, 60, 60, 60, 61,
-+ 62, 62, 63, 63, 64, 64, 65, 65, 66, 66,
-+ 67, 67, 68, 68, 68, 69, 69, 69, 69, 69,
-+ 70, 70, 70, 71, 71, 71, 72, 72, 72, 72,
-+ 73, 73, 73, 73, 74, 74, 74, 75, 75, 75,
-+ 76, 76, 76
- };
-
- /* YYR2[YYN] -- Number of symbols on the right hand side of rule YYN. */
- static const yytype_uint8 yyr2[] =
- {
-- 0, 2, 4, 0, 2, 4, 2, 2, 3, 4,
-- 3, 4, 5, 0, 2, 4, 2, 3, 2, 2,
-- 3, 4, 2, 9, 5, 2, 0, 2, 2, 3,
-- 1, 2, 2, 2, 1, 1, 3, 1, 1, 5,
-- 1, 3, 1, 3, 1, 3, 1, 3, 1, 3,
-- 1, 3, 3, 1, 3, 3, 3, 3, 3, 3,
-- 1, 3, 3, 1, 3, 3, 3, 1, 1, 2,
-- 2, 2, 0, 2, 2, 0, 2, 2, 2, 3,
-- 2
-+ 0, 2, 5, 0, 2, 0, 2, 4, 2, 2,
-+ 3, 4, 3, 4, 5, 0, 2, 4, 2, 3,
-+ 2, 2, 3, 4, 2, 9, 5, 2, 0, 2,
-+ 2, 3, 1, 2, 2, 2, 1, 1, 3, 1,
-+ 1, 5, 1, 3, 1, 3, 1, 3, 1, 3,
-+ 1, 3, 1, 3, 3, 1, 3, 3, 3, 3,
-+ 3, 3, 1, 3, 3, 1, 3, 3, 3, 1,
-+ 1, 2, 2, 2, 0, 2, 2, 0, 2, 2,
-+ 2, 3, 2
- };
-
-
-@@ -1463,65 +1466,82 @@ yyreduce:
- switch (yyn)
- {
- case 2:
--#line 105 "dtc-parser.y" /* yacc.c:1646 */
-+#line 109 "dtc-parser.y" /* yacc.c:1646 */
- {
-+ (yyvsp[0].node)->is_plugin = (yyvsp[-2].is_plugin);
- the_boot_info = build_boot_info((yyvsp[-1].re), (yyvsp[0].node),
- guess_boot_cpuid((yyvsp[0].node)));
- }
--#line 1472 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1476 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 3:
--#line 113 "dtc-parser.y" /* yacc.c:1646 */
-+#line 118 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.re) = NULL;
-+ (yyval.is_plugin) = false;
- }
--#line 1480 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1484 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 4:
--#line 117 "dtc-parser.y" /* yacc.c:1646 */
-+#line 122 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.re) = chain_reserve_entry((yyvsp[-1].re), (yyvsp[0].re));
-+ (yyval.is_plugin) = true;
- }
--#line 1488 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1492 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 5:
--#line 124 "dtc-parser.y" /* yacc.c:1646 */
-+#line 129 "dtc-parser.y" /* yacc.c:1646 */
- {
-- (yyval.re) = build_reserve_entry((yyvsp[-2].integer), (yyvsp[-1].integer));
-+ (yyval.re) = NULL;
- }
--#line 1496 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1500 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
- case 6:
--#line 128 "dtc-parser.y" /* yacc.c:1646 */
-+#line 133 "dtc-parser.y" /* yacc.c:1646 */
-+ {
-+ (yyval.re) = chain_reserve_entry((yyvsp[-1].re), (yyvsp[0].re));
-+ }
-+#line 1508 "dtc-parser.tab.c" /* yacc.c:1646 */
-+ break;
-+
-+ case 7:
-+#line 140 "dtc-parser.y" /* yacc.c:1646 */
-+ {
-+ (yyval.re) = build_reserve_entry((yyvsp[-2].integer), (yyvsp[-1].integer));
-+ }
-+#line 1516 "dtc-parser.tab.c" /* yacc.c:1646 */
-+ break;
-+
-+ case 8:
-+#line 144 "dtc-parser.y" /* yacc.c:1646 */
- {
- add_label(&(yyvsp[0].re)->labels, (yyvsp[-1].labelref));
- (yyval.re) = (yyvsp[0].re);
- }
--#line 1505 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1525 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 7:
--#line 136 "dtc-parser.y" /* yacc.c:1646 */
-+ case 9:
-+#line 152 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.node) = name_node((yyvsp[0].node), "");
- }
--#line 1513 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1533 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 8:
--#line 140 "dtc-parser.y" /* yacc.c:1646 */
-+ case 10:
-+#line 156 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.node) = merge_nodes((yyvsp[-2].node), (yyvsp[0].node));
- }
--#line 1521 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1541 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 9:
--#line 145 "dtc-parser.y" /* yacc.c:1646 */
-+ case 11:
-+#line 161 "dtc-parser.y" /* yacc.c:1646 */
- {
- struct node *target = get_node_by_ref((yyvsp[-3].node), (yyvsp[-1].labelref));
-
-@@ -1532,11 +1552,11 @@ yyreduce:
- ERROR(&(yylsp[-1]), "Label or path %s not found", (yyvsp[-1].labelref));
- (yyval.node) = (yyvsp[-3].node);
- }
--#line 1536 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1556 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 10:
--#line 156 "dtc-parser.y" /* yacc.c:1646 */
-+ case 12:
-+#line 172 "dtc-parser.y" /* yacc.c:1646 */
- {
- struct node *target = get_node_by_ref((yyvsp[-2].node), (yyvsp[-1].labelref));
-
-@@ -1546,11 +1566,11 @@ yyreduce:
- ERROR(&(yylsp[-1]), "Label or path %s not found", (yyvsp[-1].labelref));
- (yyval.node) = (yyvsp[-2].node);
- }
--#line 1550 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1570 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 11:
--#line 166 "dtc-parser.y" /* yacc.c:1646 */
-+ case 13:
-+#line 182 "dtc-parser.y" /* yacc.c:1646 */
- {
- struct node *target = get_node_by_ref((yyvsp[-3].node), (yyvsp[-1].labelref));
-
-@@ -1562,100 +1582,100 @@ yyreduce:
-
- (yyval.node) = (yyvsp[-3].node);
- }
--#line 1566 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1586 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 12:
--#line 181 "dtc-parser.y" /* yacc.c:1646 */
-+ case 14:
-+#line 197 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.node) = build_node((yyvsp[-3].proplist), (yyvsp[-2].nodelist));
- }
--#line 1574 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1594 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 13:
--#line 188 "dtc-parser.y" /* yacc.c:1646 */
-+ case 15:
-+#line 204 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.proplist) = NULL;
- }
--#line 1582 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1602 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 14:
--#line 192 "dtc-parser.y" /* yacc.c:1646 */
-+ case 16:
-+#line 208 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.proplist) = chain_property((yyvsp[0].prop), (yyvsp[-1].proplist));
- }
--#line 1590 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1610 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 15:
--#line 199 "dtc-parser.y" /* yacc.c:1646 */
-+ case 17:
-+#line 215 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.prop) = build_property((yyvsp[-3].propnodename), (yyvsp[-1].data));
- }
--#line 1598 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1618 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 16:
--#line 203 "dtc-parser.y" /* yacc.c:1646 */
-+ case 18:
-+#line 219 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.prop) = build_property((yyvsp[-1].propnodename), empty_data);
- }
--#line 1606 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1626 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 17:
--#line 207 "dtc-parser.y" /* yacc.c:1646 */
-+ case 19:
-+#line 223 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.prop) = build_property_delete((yyvsp[-1].propnodename));
- }
--#line 1614 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1634 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 18:
--#line 211 "dtc-parser.y" /* yacc.c:1646 */
-+ case 20:
-+#line 227 "dtc-parser.y" /* yacc.c:1646 */
- {
- add_label(&(yyvsp[0].prop)->labels, (yyvsp[-1].labelref));
- (yyval.prop) = (yyvsp[0].prop);
- }
--#line 1623 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1643 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 19:
--#line 219 "dtc-parser.y" /* yacc.c:1646 */
-+ case 21:
-+#line 235 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.data) = data_merge((yyvsp[-1].data), (yyvsp[0].data));
- }
--#line 1631 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1651 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 20:
--#line 223 "dtc-parser.y" /* yacc.c:1646 */
-+ case 22:
-+#line 239 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.data) = data_merge((yyvsp[-2].data), (yyvsp[-1].array).data);
- }
--#line 1639 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1659 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 21:
--#line 227 "dtc-parser.y" /* yacc.c:1646 */
-+ case 23:
-+#line 243 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.data) = data_merge((yyvsp[-3].data), (yyvsp[-1].data));
- }
--#line 1647 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1667 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 22:
--#line 231 "dtc-parser.y" /* yacc.c:1646 */
-+ case 24:
-+#line 247 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.data) = data_add_marker((yyvsp[-1].data), REF_PATH, (yyvsp[0].labelref));
- }
--#line 1655 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1675 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 23:
--#line 235 "dtc-parser.y" /* yacc.c:1646 */
-+ case 25:
-+#line 251 "dtc-parser.y" /* yacc.c:1646 */
- {
- FILE *f = srcfile_relative_open((yyvsp[-5].data).val, NULL);
- struct data d;
-@@ -1671,11 +1691,11 @@ yyreduce:
- (yyval.data) = data_merge((yyvsp[-8].data), d);
- fclose(f);
- }
--#line 1675 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1695 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 24:
--#line 251 "dtc-parser.y" /* yacc.c:1646 */
-+ case 26:
-+#line 267 "dtc-parser.y" /* yacc.c:1646 */
- {
- FILE *f = srcfile_relative_open((yyvsp[-1].data).val, NULL);
- struct data d = empty_data;
-@@ -1685,43 +1705,43 @@ yyreduce:
- (yyval.data) = data_merge((yyvsp[-4].data), d);
- fclose(f);
- }
--#line 1689 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1709 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 25:
--#line 261 "dtc-parser.y" /* yacc.c:1646 */
-+ case 27:
-+#line 277 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.data) = data_add_marker((yyvsp[-1].data), LABEL, (yyvsp[0].labelref));
- }
--#line 1697 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1717 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 26:
--#line 268 "dtc-parser.y" /* yacc.c:1646 */
-+ case 28:
-+#line 284 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.data) = empty_data;
- }
--#line 1705 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1725 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 27:
--#line 272 "dtc-parser.y" /* yacc.c:1646 */
-+ case 29:
-+#line 288 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.data) = (yyvsp[-1].data);
- }
--#line 1713 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1733 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 28:
--#line 276 "dtc-parser.y" /* yacc.c:1646 */
-+ case 30:
-+#line 292 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.data) = data_add_marker((yyvsp[-1].data), LABEL, (yyvsp[0].labelref));
- }
--#line 1721 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1741 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 29:
--#line 283 "dtc-parser.y" /* yacc.c:1646 */
-+ case 31:
-+#line 299 "dtc-parser.y" /* yacc.c:1646 */
- {
- unsigned long long bits;
-
-@@ -1737,20 +1757,20 @@ yyreduce:
- (yyval.array).data = empty_data;
- (yyval.array).bits = bits;
- }
--#line 1741 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1761 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 30:
--#line 299 "dtc-parser.y" /* yacc.c:1646 */
-+ case 32:
-+#line 315 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.array).data = empty_data;
- (yyval.array).bits = 32;
- }
--#line 1750 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1770 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 31:
--#line 304 "dtc-parser.y" /* yacc.c:1646 */
-+ case 33:
-+#line 320 "dtc-parser.y" /* yacc.c:1646 */
- {
- if ((yyvsp[-1].array).bits < 64) {
- uint64_t mask = (1ULL << (yyvsp[-1].array).bits) - 1;
-@@ -1769,11 +1789,11 @@ yyreduce:
-
- (yyval.array).data = data_append_integer((yyvsp[-1].array).data, (yyvsp[0].integer), (yyvsp[-1].array).bits);
- }
--#line 1773 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1793 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 32:
--#line 323 "dtc-parser.y" /* yacc.c:1646 */
-+ case 34:
-+#line 339 "dtc-parser.y" /* yacc.c:1646 */
- {
- uint64_t val = ~0ULL >> (64 - (yyvsp[-1].array).bits);
-
-@@ -1787,233 +1807,233 @@ yyreduce:
-
- (yyval.array).data = data_append_integer((yyvsp[-1].array).data, val, (yyvsp[-1].array).bits);
- }
--#line 1791 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1811 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 33:
--#line 337 "dtc-parser.y" /* yacc.c:1646 */
-+ case 35:
-+#line 353 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.array).data = data_add_marker((yyvsp[-1].array).data, LABEL, (yyvsp[0].labelref));
- }
--#line 1799 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1819 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 36:
--#line 346 "dtc-parser.y" /* yacc.c:1646 */
-+ case 38:
-+#line 362 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.integer) = (yyvsp[-1].integer);
- }
--#line 1807 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1827 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 39:
--#line 357 "dtc-parser.y" /* yacc.c:1646 */
-+ case 41:
-+#line 373 "dtc-parser.y" /* yacc.c:1646 */
- { (yyval.integer) = (yyvsp[-4].integer) ? (yyvsp[-2].integer) : (yyvsp[0].integer); }
--#line 1813 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1833 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 41:
--#line 362 "dtc-parser.y" /* yacc.c:1646 */
-+ case 43:
-+#line 378 "dtc-parser.y" /* yacc.c:1646 */
- { (yyval.integer) = (yyvsp[-2].integer) || (yyvsp[0].integer); }
--#line 1819 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1839 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 43:
--#line 367 "dtc-parser.y" /* yacc.c:1646 */
-+ case 45:
-+#line 383 "dtc-parser.y" /* yacc.c:1646 */
- { (yyval.integer) = (yyvsp[-2].integer) && (yyvsp[0].integer); }
--#line 1825 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1845 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 45:
--#line 372 "dtc-parser.y" /* yacc.c:1646 */
-+ case 47:
-+#line 388 "dtc-parser.y" /* yacc.c:1646 */
- { (yyval.integer) = (yyvsp[-2].integer) | (yyvsp[0].integer); }
--#line 1831 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1851 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 47:
--#line 377 "dtc-parser.y" /* yacc.c:1646 */
-+ case 49:
-+#line 393 "dtc-parser.y" /* yacc.c:1646 */
- { (yyval.integer) = (yyvsp[-2].integer) ^ (yyvsp[0].integer); }
--#line 1837 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1857 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 49:
--#line 382 "dtc-parser.y" /* yacc.c:1646 */
-+ case 51:
-+#line 398 "dtc-parser.y" /* yacc.c:1646 */
- { (yyval.integer) = (yyvsp[-2].integer) & (yyvsp[0].integer); }
--#line 1843 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1863 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 51:
--#line 387 "dtc-parser.y" /* yacc.c:1646 */
-+ case 53:
-+#line 403 "dtc-parser.y" /* yacc.c:1646 */
- { (yyval.integer) = (yyvsp[-2].integer) == (yyvsp[0].integer); }
--#line 1849 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1869 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 52:
--#line 388 "dtc-parser.y" /* yacc.c:1646 */
-+ case 54:
-+#line 404 "dtc-parser.y" /* yacc.c:1646 */
- { (yyval.integer) = (yyvsp[-2].integer) != (yyvsp[0].integer); }
--#line 1855 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1875 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 54:
--#line 393 "dtc-parser.y" /* yacc.c:1646 */
-+ case 56:
-+#line 409 "dtc-parser.y" /* yacc.c:1646 */
- { (yyval.integer) = (yyvsp[-2].integer) < (yyvsp[0].integer); }
--#line 1861 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1881 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 55:
--#line 394 "dtc-parser.y" /* yacc.c:1646 */
-+ case 57:
-+#line 410 "dtc-parser.y" /* yacc.c:1646 */
- { (yyval.integer) = (yyvsp[-2].integer) > (yyvsp[0].integer); }
--#line 1867 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1887 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 56:
--#line 395 "dtc-parser.y" /* yacc.c:1646 */
-+ case 58:
-+#line 411 "dtc-parser.y" /* yacc.c:1646 */
- { (yyval.integer) = (yyvsp[-2].integer) <= (yyvsp[0].integer); }
--#line 1873 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1893 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 57:
--#line 396 "dtc-parser.y" /* yacc.c:1646 */
-+ case 59:
-+#line 412 "dtc-parser.y" /* yacc.c:1646 */
- { (yyval.integer) = (yyvsp[-2].integer) >= (yyvsp[0].integer); }
--#line 1879 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1899 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 58:
--#line 400 "dtc-parser.y" /* yacc.c:1646 */
-+ case 60:
-+#line 416 "dtc-parser.y" /* yacc.c:1646 */
- { (yyval.integer) = (yyvsp[-2].integer) << (yyvsp[0].integer); }
--#line 1885 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1905 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 59:
--#line 401 "dtc-parser.y" /* yacc.c:1646 */
-+ case 61:
-+#line 417 "dtc-parser.y" /* yacc.c:1646 */
- { (yyval.integer) = (yyvsp[-2].integer) >> (yyvsp[0].integer); }
--#line 1891 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1911 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 61:
--#line 406 "dtc-parser.y" /* yacc.c:1646 */
-+ case 63:
-+#line 422 "dtc-parser.y" /* yacc.c:1646 */
- { (yyval.integer) = (yyvsp[-2].integer) + (yyvsp[0].integer); }
--#line 1897 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1917 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 62:
--#line 407 "dtc-parser.y" /* yacc.c:1646 */
-+ case 64:
-+#line 423 "dtc-parser.y" /* yacc.c:1646 */
- { (yyval.integer) = (yyvsp[-2].integer) - (yyvsp[0].integer); }
--#line 1903 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1923 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 64:
--#line 412 "dtc-parser.y" /* yacc.c:1646 */
-+ case 66:
-+#line 428 "dtc-parser.y" /* yacc.c:1646 */
- { (yyval.integer) = (yyvsp[-2].integer) * (yyvsp[0].integer); }
--#line 1909 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1929 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 65:
--#line 413 "dtc-parser.y" /* yacc.c:1646 */
-+ case 67:
-+#line 429 "dtc-parser.y" /* yacc.c:1646 */
- { (yyval.integer) = (yyvsp[-2].integer) / (yyvsp[0].integer); }
--#line 1915 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1935 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 66:
--#line 414 "dtc-parser.y" /* yacc.c:1646 */
-+ case 68:
-+#line 430 "dtc-parser.y" /* yacc.c:1646 */
- { (yyval.integer) = (yyvsp[-2].integer) % (yyvsp[0].integer); }
--#line 1921 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1941 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 69:
--#line 420 "dtc-parser.y" /* yacc.c:1646 */
-+ case 71:
-+#line 436 "dtc-parser.y" /* yacc.c:1646 */
- { (yyval.integer) = -(yyvsp[0].integer); }
--#line 1927 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1947 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 70:
--#line 421 "dtc-parser.y" /* yacc.c:1646 */
-+ case 72:
-+#line 437 "dtc-parser.y" /* yacc.c:1646 */
- { (yyval.integer) = ~(yyvsp[0].integer); }
--#line 1933 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1953 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 71:
--#line 422 "dtc-parser.y" /* yacc.c:1646 */
-+ case 73:
-+#line 438 "dtc-parser.y" /* yacc.c:1646 */
- { (yyval.integer) = !(yyvsp[0].integer); }
--#line 1939 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1959 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 72:
--#line 427 "dtc-parser.y" /* yacc.c:1646 */
-+ case 74:
-+#line 443 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.data) = empty_data;
- }
--#line 1947 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1967 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 73:
--#line 431 "dtc-parser.y" /* yacc.c:1646 */
-+ case 75:
-+#line 447 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.data) = data_append_byte((yyvsp[-1].data), (yyvsp[0].byte));
- }
--#line 1955 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1975 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 74:
--#line 435 "dtc-parser.y" /* yacc.c:1646 */
-+ case 76:
-+#line 451 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.data) = data_add_marker((yyvsp[-1].data), LABEL, (yyvsp[0].labelref));
- }
--#line 1963 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1983 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 75:
--#line 442 "dtc-parser.y" /* yacc.c:1646 */
-+ case 77:
-+#line 458 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.nodelist) = NULL;
- }
--#line 1971 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1991 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 76:
--#line 446 "dtc-parser.y" /* yacc.c:1646 */
-+ case 78:
-+#line 462 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.nodelist) = chain_node((yyvsp[-1].node), (yyvsp[0].nodelist));
- }
--#line 1979 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 1999 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 77:
--#line 450 "dtc-parser.y" /* yacc.c:1646 */
-+ case 79:
-+#line 466 "dtc-parser.y" /* yacc.c:1646 */
- {
- ERROR(&(yylsp[0]), "Properties must precede subnodes");
- YYERROR;
- }
--#line 1988 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 2008 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 78:
--#line 458 "dtc-parser.y" /* yacc.c:1646 */
-+ case 80:
-+#line 474 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.node) = name_node((yyvsp[0].node), (yyvsp[-1].propnodename));
- }
--#line 1996 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 2016 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 79:
--#line 462 "dtc-parser.y" /* yacc.c:1646 */
-+ case 81:
-+#line 478 "dtc-parser.y" /* yacc.c:1646 */
- {
- (yyval.node) = name_node(build_node_delete(), (yyvsp[-1].propnodename));
- }
--#line 2004 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 2024 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-- case 80:
--#line 466 "dtc-parser.y" /* yacc.c:1646 */
-+ case 82:
-+#line 482 "dtc-parser.y" /* yacc.c:1646 */
- {
- add_label(&(yyvsp[0].node)->labels, (yyvsp[-1].labelref));
- (yyval.node) = (yyvsp[0].node);
- }
--#line 2013 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 2033 "dtc-parser.tab.c" /* yacc.c:1646 */
- break;
-
-
--#line 2017 "dtc-parser.tab.c" /* yacc.c:1646 */
-+#line 2037 "dtc-parser.tab.c" /* yacc.c:1646 */
- default: break;
- }
- /* User semantic actions sometimes alter yychar, and that requires
-@@ -2248,7 +2268,7 @@ yyreturn:
- #endif
- return yyresult;
- }
--#line 472 "dtc-parser.y" /* yacc.c:1906 */
-+#line 488 "dtc-parser.y" /* yacc.c:1906 */
-
-
- void yyerror(char const *s)
---- a/scripts/dtc/dtc-parser.tab.h_shipped
-+++ b/scripts/dtc/dtc-parser.tab.h_shipped
-@@ -46,26 +46,27 @@ extern int yydebug;
- enum yytokentype
- {
- DT_V1 = 258,
-- DT_MEMRESERVE = 259,
-- DT_LSHIFT = 260,
-- DT_RSHIFT = 261,
-- DT_LE = 262,
-- DT_GE = 263,
-- DT_EQ = 264,
-- DT_NE = 265,
-- DT_AND = 266,
-- DT_OR = 267,
-- DT_BITS = 268,
-- DT_DEL_PROP = 269,
-- DT_DEL_NODE = 270,
-- DT_PROPNODENAME = 271,
-- DT_LITERAL = 272,
-- DT_CHAR_LITERAL = 273,
-- DT_BYTE = 274,
-- DT_STRING = 275,
-- DT_LABEL = 276,
-- DT_REF = 277,
-- DT_INCBIN = 278
-+ DT_PLUGIN = 259,
-+ DT_MEMRESERVE = 260,
-+ DT_LSHIFT = 261,
-+ DT_RSHIFT = 262,
-+ DT_LE = 263,
-+ DT_GE = 264,
-+ DT_EQ = 265,
-+ DT_NE = 266,
-+ DT_AND = 267,
-+ DT_OR = 268,
-+ DT_BITS = 269,
-+ DT_DEL_PROP = 270,
-+ DT_DEL_NODE = 271,
-+ DT_PROPNODENAME = 272,
-+ DT_LITERAL = 273,
-+ DT_CHAR_LITERAL = 274,
-+ DT_BYTE = 275,
-+ DT_STRING = 276,
-+ DT_LABEL = 277,
-+ DT_REF = 278,
-+ DT_INCBIN = 279
- };
- #endif
-
-@@ -74,7 +75,7 @@ extern int yydebug;
- typedef union YYSTYPE YYSTYPE;
- union YYSTYPE
- {
--#line 38 "dtc-parser.y" /* yacc.c:1909 */
-+#line 39 "dtc-parser.y" /* yacc.c:1909 */
-
- char *propnodename;
- char *labelref;
-@@ -92,8 +93,9 @@ union YYSTYPE
- struct node *nodelist;
- struct reserve_info *re;
- uint64_t integer;
-+ bool is_plugin;
-
--#line 97 "dtc-parser.tab.h" /* yacc.c:1909 */
-+#line 99 "dtc-parser.tab.h" /* yacc.c:1909 */
- };
- # define YYSTYPE_IS_TRIVIAL 1
- # define YYSTYPE_IS_DECLARED 1
---- a/scripts/dtc/dtc-parser.y
-+++ b/scripts/dtc/dtc-parser.y
-@@ -19,6 +19,7 @@
- */
- %{
- #include <stdio.h>
-+#include <inttypes.h>
-
- #include "dtc.h"
- #include "srcpos.h"
-@@ -52,9 +53,11 @@ extern bool treesource_error;
- struct node *nodelist;
- struct reserve_info *re;
- uint64_t integer;
-+ bool is_plugin;
- }
-
- %token DT_V1
-+%token DT_PLUGIN
- %token DT_MEMRESERVE
- %token DT_LSHIFT DT_RSHIFT DT_LE DT_GE DT_EQ DT_NE DT_AND DT_OR
- %token DT_BITS
-@@ -71,6 +74,7 @@ extern bool treesource_error;
-
- %type <data> propdata
- %type <data> propdataprefix
-+%type <is_plugin> plugindecl
- %type <re> memreserve
- %type <re> memreserves
- %type <array> arrayprefix
-@@ -101,10 +105,22 @@ extern bool treesource_error;
- %%
-
- sourcefile:
-- DT_V1 ';' memreserves devicetree
-+ DT_V1 ';' plugindecl memreserves devicetree
- {
-- the_boot_info = build_boot_info($3, $4,
-- guess_boot_cpuid($4));
-+ $5->is_plugin = $3;
-+ the_boot_info = build_boot_info($4, $5,
-+ guess_boot_cpuid($5));
-+ }
-+ ;
-+
-+plugindecl:
-+ /* empty */
-+ {
-+ $$ = false;
-+ }
-+ | DT_PLUGIN ';'
-+ {
-+ $$ = true;
- }
- ;
-
---- a/scripts/dtc/dtc.c
-+++ b/scripts/dtc/dtc.c
-@@ -29,6 +29,7 @@ int reservenum; /* Number of memory res
- int minsize; /* Minimum blob size */
- int padsize; /* Additional padding to blob */
- int phandle_format = PHANDLE_BOTH; /* Use linux,phandle or phandle properties */
-+int symbol_fixup_support = 0;
-
- static void fill_fullpaths(struct node *tree, const char *prefix)
- {
-@@ -51,7 +52,7 @@ static void fill_fullpaths(struct node *
- #define FDT_VERSION(version) _FDT_VERSION(version)
- #define _FDT_VERSION(version) #version
- static const char usage_synopsis[] = "dtc [options] <input file>";
--static const char usage_short_opts[] = "qI:O:o:V:d:R:S:p:fb:i:H:sW:E:hv";
-+static const char usage_short_opts[] = "qI:O:o:V:d:R:S:p:fb:i:H:sW:E:@hv";
- static struct option const usage_long_opts[] = {
- {"quiet", no_argument, NULL, 'q'},
- {"in-format", a_argument, NULL, 'I'},
-@@ -69,6 +70,7 @@ static struct option const usage_long_op
- {"phandle", a_argument, NULL, 'H'},
- {"warning", a_argument, NULL, 'W'},
- {"error", a_argument, NULL, 'E'},
-+ {"symbols", no_argument, NULL, '@'},
- {"help", no_argument, NULL, 'h'},
- {"version", no_argument, NULL, 'v'},
- {NULL, no_argument, NULL, 0x0},
-@@ -99,6 +101,7 @@ static const char * const usage_opts_hel
- "\t\tboth - Both \"linux,phandle\" and \"phandle\" properties",
- "\n\tEnable/disable warnings (prefix with \"no-\")",
- "\n\tEnable/disable errors (prefix with \"no-\")",
-+ "\n\tEnable symbols/fixup support",
- "\n\tPrint this help and exit",
- "\n\tPrint version and exit",
- NULL,
-@@ -186,7 +189,9 @@ int main(int argc, char *argv[])
- case 'E':
- parse_checks_option(false, true, optarg);
- break;
--
-+ case '@':
-+ symbol_fixup_support = 1;
-+ break;
- case 'h':
- usage(NULL);
- default:
---- a/scripts/dtc/dtc.h
-+++ b/scripts/dtc/dtc.h
-@@ -54,6 +54,7 @@ extern int reservenum; /* Number of mem
- extern int minsize; /* Minimum blob size */
- extern int padsize; /* Additional padding to blob */
- extern int phandle_format; /* Use linux,phandle or phandle properties */
-+extern int symbol_fixup_support;/* enable symbols & fixup support */
-
- #define PHANDLE_LEGACY 0x1
- #define PHANDLE_EPAPR 0x2
-@@ -132,6 +133,26 @@ struct label {
- struct label *next;
- };
-
-+struct fixup_entry {
-+ int offset;
-+ struct node *node;
-+ struct property *prop;
-+ struct fixup_entry *next;
-+ bool local_fixup_generated;
-+};
-+
-+struct fixup {
-+ char *ref;
-+ struct fixup_entry *entries;
-+ struct fixup *next;
-+};
-+
-+struct symbol {
-+ struct label *label;
-+ struct node *node;
-+ struct symbol *next;
-+};
-+
- struct property {
- bool deleted;
- char *name;
-@@ -158,6 +179,13 @@ struct node {
- int addr_cells, size_cells;
-
- struct label *labels;
-+
-+ struct symbol *symbols;
-+ struct fixup_entry *local_fixups;
-+ bool emit_local_fixup_node;
-+
-+ bool is_plugin;
-+ struct fixup *fixups;
- };
-
- #define for_each_label_withdel(l0, l) \
-@@ -181,6 +209,18 @@ struct node {
- for_each_child_withdel(n, c) \
- if (!(c)->deleted)
-
-+#define for_each_fixup(n, f) \
-+ for ((f) = (n)->fixups; (f); (f) = (f)->next)
-+
-+#define for_each_fixup_entry(f, fe) \
-+ for ((fe) = (f)->entries; (fe); (fe) = (fe)->next)
-+
-+#define for_each_symbol(n, s) \
-+ for ((s) = (n)->symbols; (s); (s) = (s)->next)
-+
-+#define for_each_local_fixup_entry(n, fe) \
-+ for ((fe) = (n)->local_fixups; (fe); (fe) = (fe)->next)
-+
- void add_label(struct label **labels, char *label);
- void delete_labels(struct label **labels);
-
---- a/scripts/dtc/flattree.c
-+++ b/scripts/dtc/flattree.c
-@@ -255,6 +255,204 @@ static int stringtable_insert(struct dat
- return i;
- }
-
-+static void emit_local_fixups(struct node *tree, struct emitter *emit,
-+ void *etarget, struct data *strbuf, struct version_info *vi,
-+ struct node *node)
-+{
-+ struct fixup_entry *fe, *fen;
-+ struct node *child;
-+ int nameoff, count;
-+ cell_t *buf;
-+ struct data d;
-+
-+ if (node->emit_local_fixup_node) {
-+
-+ /* emit the external fixups (do not emit /) */
-+ if (node != tree) {
-+ emit->beginnode(etarget, NULL);
-+ emit->string(etarget, node->name, 0);
-+ emit->align(etarget, sizeof(cell_t));
-+ }
-+
-+ for_each_local_fixup_entry(tree, fe) {
-+ if (fe->node != node || fe->local_fixup_generated)
-+ continue;
-+
-+ /* count the number of fixup entries */
-+ count = 0;
-+ for_each_local_fixup_entry(tree, fen) {
-+ if (fen->prop != fe->prop)
-+ continue;
-+ fen->local_fixup_generated = true;
-+ count++;
-+ }
-+
-+ /* allocate buffer */
-+ buf = xmalloc(count * sizeof(cell_t));
-+
-+ /* collect all the offsets in buffer */
-+ count = 0;
-+ for_each_local_fixup_entry(tree, fen) {
-+ if (fen->prop != fe->prop)
-+ continue;
-+ fen->local_fixup_generated = true;
-+ buf[count++] = cpu_to_fdt32(fen->offset);
-+ }
-+ d = empty_data;
-+ d.len = count * sizeof(cell_t);
-+ d.val = (char *)buf;
-+
-+ nameoff = stringtable_insert(strbuf, fe->prop->name);
-+ emit->property(etarget, fe->prop->labels);
-+ emit->cell(etarget, count * sizeof(cell_t));
-+ emit->cell(etarget, nameoff);
-+
-+ if ((vi->flags & FTF_VARALIGN) &&
-+ (count * sizeof(cell_t)) >= 8)
-+ emit->align(etarget, 8);
-+
-+ emit->data(etarget, d);
-+ emit->align(etarget, sizeof(cell_t));
-+
-+ free(buf);
-+ }
-+ }
-+
-+ for_each_child(node, child)
-+ emit_local_fixups(tree, emit, etarget, strbuf, vi, child);
-+
-+ if (node->emit_local_fixup_node && node != tree)
-+ emit->endnode(etarget, tree->labels);
-+}
-+
-+static void emit_symbols_node(struct node *tree, struct emitter *emit,
-+ void *etarget, struct data *strbuf,
-+ struct version_info *vi)
-+{
-+ struct symbol *sym;
-+ int nameoff, vallen;
-+
-+ /* do nothing if no symbols */
-+ if (!tree->symbols)
-+ return;
-+
-+ emit->beginnode(etarget, NULL);
-+ emit->string(etarget, "__symbols__", 0);
-+ emit->align(etarget, sizeof(cell_t));
-+
-+ for_each_symbol(tree, sym) {
-+
-+ vallen = strlen(sym->node->fullpath);
-+
-+ nameoff = stringtable_insert(strbuf, sym->label->label);
-+
-+ emit->property(etarget, NULL);
-+ emit->cell(etarget, vallen + 1);
-+ emit->cell(etarget, nameoff);
-+
-+ if ((vi->flags & FTF_VARALIGN) && vallen >= 8)
-+ emit->align(etarget, 8);
-+
-+ emit->string(etarget, sym->node->fullpath,
-+ strlen(sym->node->fullpath));
-+ emit->align(etarget, sizeof(cell_t));
-+ }
-+
-+ emit->endnode(etarget, NULL);
-+}
-+
-+static void emit_local_fixups_node(struct node *tree, struct emitter *emit,
-+ void *etarget, struct data *strbuf,
-+ struct version_info *vi)
-+{
-+ struct fixup_entry *fe;
-+ struct node *node;
-+
-+ /* do nothing if no local fixups */
-+ if (!tree->local_fixups)
-+ return;
-+
-+ /* mark all nodes that need a local fixup generated (and parents) */
-+ for_each_local_fixup_entry(tree, fe) {
-+ node = fe->node;
-+ while (node != NULL && !node->emit_local_fixup_node) {
-+ node->emit_local_fixup_node = true;
-+ node = node->parent;
-+ }
-+ }
-+
-+ /* emit the local fixups node now */
-+ emit->beginnode(etarget, NULL);
-+ emit->string(etarget, "__local_fixups__", 0);
-+ emit->align(etarget, sizeof(cell_t));
-+
-+ emit_local_fixups(tree, emit, etarget, strbuf, vi, tree);
-+
-+ emit->endnode(etarget, tree->labels);
-+}
-+
-+static void emit_fixups_node(struct node *tree, struct emitter *emit,
-+ void *etarget, struct data *strbuf,
-+ struct version_info *vi)
-+{
-+ struct fixup *f;
-+ struct fixup_entry *fe;
-+ char *name, *s;
-+ const char *fullpath;
-+ int namesz, nameoff, vallen;
-+
-+ /* do nothing if no fixups */
-+ if (!tree->fixups)
-+ return;
-+
-+ /* emit the external fixups */
-+ emit->beginnode(etarget, NULL);
-+ emit->string(etarget, "__fixups__", 0);
-+ emit->align(etarget, sizeof(cell_t));
-+
-+ for_each_fixup(tree, f) {
-+
-+ namesz = 0;
-+ for_each_fixup_entry(f, fe) {
-+ fullpath = fe->node->fullpath;
-+ if (fullpath[0] == '\0')
-+ fullpath = "/";
-+ namesz += strlen(fullpath) + 1;
-+ namesz += strlen(fe->prop->name) + 1;
-+ namesz += 32; /* space for :<number> + '\0' */
-+ }
-+
-+ name = xmalloc(namesz);
-+
-+ s = name;
-+ for_each_fixup_entry(f, fe) {
-+ fullpath = fe->node->fullpath;
-+ if (fullpath[0] == '\0')
-+ fullpath = "/";
-+ snprintf(s, name + namesz - s, "%s:%s:%d", fullpath,
-+ fe->prop->name, fe->offset);
-+ s += strlen(s) + 1;
-+ }
-+
-+ nameoff = stringtable_insert(strbuf, f->ref);
-+ vallen = s - name - 1;
-+
-+ emit->property(etarget, NULL);
-+ emit->cell(etarget, vallen + 1);
-+ emit->cell(etarget, nameoff);
-+
-+ if ((vi->flags & FTF_VARALIGN) && vallen >= 8)
-+ emit->align(etarget, 8);
-+
-+ emit->string(etarget, name, vallen);
-+ emit->align(etarget, sizeof(cell_t));
-+
-+ free(name);
-+ }
-+
-+ emit->endnode(etarget, tree->labels);
-+}
-+
- static void flatten_tree(struct node *tree, struct emitter *emit,
- void *etarget, struct data *strbuf,
- struct version_info *vi)
-@@ -310,6 +508,10 @@ static void flatten_tree(struct node *tr
- flatten_tree(child, emit, etarget, strbuf, vi);
- }
-
-+ emit_symbols_node(tree, emit, etarget, strbuf, vi);
-+ emit_local_fixups_node(tree, emit, etarget, strbuf, vi);
-+ emit_fixups_node(tree, emit, etarget, strbuf, vi);
-+
- emit->endnode(etarget, tree->labels);
- }
-
---- a/scripts/dtc/version_gen.h
-+++ b/scripts/dtc/version_gen.h
-@@ -1 +1 @@
--#define DTC_VERSION "DTC 1.4.1-g9d3649bd"
-+#define DTC_VERSION "DTC 1.4.1-g25efc119"
diff --git a/target/linux/brcm2708/patches-4.4/0177-configfs-implement-binary-attributes.patch b/target/linux/brcm2708/patches-4.4/0177-configfs-implement-binary-attributes.patch
deleted file mode 100644
index f337d61..0000000
--- a/target/linux/brcm2708/patches-4.4/0177-configfs-implement-binary-attributes.patch
+++ /dev/null
@@ -1,639 +0,0 @@
-From 76827059f7092a0d871db592abdfd287e4d4cb60 Mon Sep 17 00:00:00 2001
-From: Pantelis Antoniou <pantelis.antoniou at konsulko.com>
-Date: Thu, 22 Oct 2015 23:30:04 +0300
-Subject: [PATCH] configfs: implement binary attributes
-
-ConfigFS lacked binary attributes up until now. This patch
-introduces support for binary attributes in a somewhat similar
-manner of sysfs binary attributes albeit with changes that
-fit the configfs usage model.
-
-Problems that configfs binary attributes fix are everything that
-requires a binary blob as part of the configuration of a resource,
-such as bitstream loading for FPGAs, DTBs for dynamically created
-devices etc.
-
-Look at Documentation/filesystems/configfs/configfs.txt for internals
-and howto use them.
-
-This patch is against linux-next as of today that contains
-Christoph's configfs rework.
-
-Signed-off-by: Pantelis Antoniou <pantelis.antoniou at konsulko.com>
-[hch: folded a fix from Geert Uytterhoeven <geert+renesas at glider.be>]
-[hch: a few tiny updates based on review feedback]
-Signed-off-by: Christoph Hellwig <hch at lst.de>
----
- Documentation/filesystems/configfs/configfs.txt | 57 +++++-
- fs/configfs/configfs_internal.h | 14 +-
- fs/configfs/dir.c | 18 +-
- fs/configfs/file.c | 255 +++++++++++++++++++++++-
- fs/configfs/inode.c | 2 +-
- include/linux/configfs.h | 50 +++++
- 6 files changed, 374 insertions(+), 22 deletions(-)
-
---- a/Documentation/filesystems/configfs/configfs.txt
-+++ b/Documentation/filesystems/configfs/configfs.txt
-@@ -51,15 +51,27 @@ configfs tree is always there, whether m
- An item is created via mkdir(2). The item's attributes will also
- appear at this time. readdir(3) can determine what the attributes are,
- read(2) can query their default values, and write(2) can store new
--values. Like sysfs, attributes should be ASCII text files, preferably
--with only one value per file. The same efficiency caveats from sysfs
--apply. Don't mix more than one attribute in one attribute file.
--
--Like sysfs, configfs expects write(2) to store the entire buffer at
--once. When writing to configfs attributes, userspace processes should
--first read the entire file, modify the portions they wish to change, and
--then write the entire buffer back. Attribute files have a maximum size
--of one page (PAGE_SIZE, 4096 on i386).
-+values. Don't mix more than one attribute in one attribute file.
-+
-+There are two types of configfs attributes:
-+
-+* Normal attributes, which similar to sysfs attributes, are small ASCII text
-+files, with a maximum size of one page (PAGE_SIZE, 4096 on i386). Preferably
-+only one value per file should be used, and the same caveats from sysfs apply.
-+Configfs expects write(2) to store the entire buffer at once. When writing to
-+normal configfs attributes, userspace processes should first read the entire
-+file, modify the portions they wish to change, and then write the entire
-+buffer back.
-+
-+* Binary attributes, which are somewhat similar to sysfs binary attributes,
-+but with a few slight changes to semantics. The PAGE_SIZE limitation does not
-+apply, but the whole binary item must fit in single kernel vmalloc'ed buffer.
-+The write(2) calls from user space are buffered, and the attributes'
-+write_bin_attribute method will be invoked on the final close, therefore it is
-+imperative for user-space to check the return code of close(2) in order to
-+verify that the operation finished successfully.
-+To avoid a malicious user OOMing the kernel, there's a per-binary attribute
-+maximum buffer value.
-
- When an item needs to be destroyed, remove it with rmdir(2). An
- item cannot be destroyed if any other item has a link to it (via
-@@ -171,6 +183,7 @@ among other things. For that, it needs
- struct configfs_item_operations *ct_item_ops;
- struct configfs_group_operations *ct_group_ops;
- struct configfs_attribute **ct_attrs;
-+ struct configfs_bin_attribute **ct_bin_attrs;
- };
-
- The most basic function of a config_item_type is to define what
-@@ -201,6 +214,32 @@ be called whenever userspace asks for a
- attribute is writable and provides a ->store method, that method will be
- be called whenever userspace asks for a write(2) on the attribute.
-
-+[struct configfs_bin_attribute]
-+
-+ struct configfs_attribute {
-+ struct configfs_attribute cb_attr;
-+ void *cb_private;
-+ size_t cb_max_size;
-+ };
-+
-+The binary attribute is used when the one needs to use binary blob to
-+appear as the contents of a file in the item's configfs directory.
-+To do so add the binary attribute to the NULL-terminated array
-+config_item_type->ct_bin_attrs, and the item appears in configfs, the
-+attribute file will appear with the configfs_bin_attribute->cb_attr.ca_name
-+filename. configfs_bin_attribute->cb_attr.ca_mode specifies the file
-+permissions.
-+The cb_private member is provided for use by the driver, while the
-+cb_max_size member specifies the maximum amount of vmalloc buffer
-+to be used.
-+
-+If binary attribute is readable and the config_item provides a
-+ct_item_ops->read_bin_attribute() method, that method will be called
-+whenever userspace asks for a read(2) on the attribute. The converse
-+will happen for write(2). The reads/writes are bufferred so only a
-+single read/write will occur; the attributes' need not concern itself
-+with it.
-+
- [struct config_group]
-
- A config_item cannot live in a vacuum. The only way one can be created
---- a/fs/configfs/configfs_internal.h
-+++ b/fs/configfs/configfs_internal.h
-@@ -53,13 +53,14 @@ struct configfs_dirent {
- #define CONFIGFS_ROOT 0x0001
- #define CONFIGFS_DIR 0x0002
- #define CONFIGFS_ITEM_ATTR 0x0004
-+#define CONFIGFS_ITEM_BIN_ATTR 0x0008
- #define CONFIGFS_ITEM_LINK 0x0020
- #define CONFIGFS_USET_DIR 0x0040
- #define CONFIGFS_USET_DEFAULT 0x0080
- #define CONFIGFS_USET_DROPPING 0x0100
- #define CONFIGFS_USET_IN_MKDIR 0x0200
- #define CONFIGFS_USET_CREATING 0x0400
--#define CONFIGFS_NOT_PINNED (CONFIGFS_ITEM_ATTR)
-+#define CONFIGFS_NOT_PINNED (CONFIGFS_ITEM_ATTR | CONFIGFS_ITEM_BIN_ATTR)
-
- extern struct mutex configfs_symlink_mutex;
- extern spinlock_t configfs_dirent_lock;
-@@ -72,6 +73,8 @@ extern struct inode * configfs_new_inode
- extern int configfs_create(struct dentry *, umode_t mode, void (*init)(struct inode *));
-
- extern int configfs_create_file(struct config_item *, const struct configfs_attribute *);
-+extern int configfs_create_bin_file(struct config_item *,
-+ const struct configfs_bin_attribute *);
- extern int configfs_make_dirent(struct configfs_dirent *,
- struct dentry *, void *, umode_t, int);
- extern int configfs_dirent_is_ready(struct configfs_dirent *);
-@@ -88,7 +91,7 @@ extern void configfs_release_fs(void);
- extern struct rw_semaphore configfs_rename_sem;
- extern const struct file_operations configfs_dir_operations;
- extern const struct file_operations configfs_file_operations;
--extern const struct file_operations bin_fops;
-+extern const struct file_operations configfs_bin_file_operations;
- extern const struct inode_operations configfs_dir_inode_operations;
- extern const struct inode_operations configfs_root_inode_operations;
- extern const struct inode_operations configfs_symlink_inode_operations;
-@@ -119,6 +122,13 @@ static inline struct configfs_attribute
- return ((struct configfs_attribute *) sd->s_element);
- }
-
-+static inline struct configfs_bin_attribute *to_bin_attr(struct dentry *dentry)
-+{
-+ struct configfs_attribute *attr = to_attr(dentry);
-+
-+ return container_of(attr, struct configfs_bin_attribute, cb_attr);
-+}
-+
- static inline struct config_item *configfs_get_config_item(struct dentry *dentry)
- {
- struct config_item * item = NULL;
---- a/fs/configfs/dir.c
-+++ b/fs/configfs/dir.c
-@@ -255,6 +255,12 @@ static void configfs_init_file(struct in
- inode->i_fop = &configfs_file_operations;
- }
-
-+static void configfs_init_bin_file(struct inode *inode)
-+{
-+ inode->i_size = 0;
-+ inode->i_fop = &configfs_bin_file_operations;
-+}
-+
- static void init_symlink(struct inode * inode)
- {
- inode->i_op = &configfs_symlink_inode_operations;
-@@ -423,7 +429,9 @@ static int configfs_attach_attr(struct c
- spin_unlock(&configfs_dirent_lock);
-
- error = configfs_create(dentry, (attr->ca_mode & S_IALLUGO) | S_IFREG,
-- configfs_init_file);
-+ (sd->s_type & CONFIGFS_ITEM_BIN_ATTR) ?
-+ configfs_init_bin_file :
-+ configfs_init_file);
- if (error) {
- configfs_put(sd);
- return error;
-@@ -583,6 +591,7 @@ static int populate_attrs(struct config_
- {
- struct config_item_type *t = item->ci_type;
- struct configfs_attribute *attr;
-+ struct configfs_bin_attribute *bin_attr;
- int error = 0;
- int i;
-
-@@ -594,6 +603,13 @@ static int populate_attrs(struct config_
- break;
- }
- }
-+ if (t->ct_bin_attrs) {
-+ for (i = 0; (bin_attr = t->ct_bin_attrs[i]) != NULL; i++) {
-+ error = configfs_create_bin_file(item, bin_attr);
-+ if (error)
-+ break;
-+ }
-+ }
-
- if (error)
- detach_attrs(item);
---- a/fs/configfs/file.c
-+++ b/fs/configfs/file.c
-@@ -28,6 +28,7 @@
- #include <linux/module.h>
- #include <linux/slab.h>
- #include <linux/mutex.h>
-+#include <linux/vmalloc.h>
- #include <asm/uaccess.h>
-
- #include <linux/configfs.h>
-@@ -48,6 +49,10 @@ struct configfs_buffer {
- struct configfs_item_operations * ops;
- struct mutex mutex;
- int needs_read_fill;
-+ bool read_in_progress;
-+ bool write_in_progress;
-+ char *bin_buffer;
-+ int bin_buffer_size;
- };
-
-
-@@ -123,6 +128,87 @@ out:
- return retval;
- }
-
-+/**
-+ * configfs_read_bin_file - read a binary attribute.
-+ * @file: file pointer.
-+ * @buf: buffer to fill.
-+ * @count: number of bytes to read.
-+ * @ppos: starting offset in file.
-+ *
-+ * Userspace wants to read a binary attribute file. The attribute
-+ * descriptor is in the file's ->d_fsdata. The target item is in the
-+ * directory's ->d_fsdata.
-+ *
-+ * We check whether we need to refill the buffer. If so we will
-+ * call the attributes' attr->read() twice. The first time we
-+ * will pass a NULL as a buffer pointer, which the attributes' method
-+ * will use to return the size of the buffer required. If no error
-+ * occurs we will allocate the buffer using vmalloc and call
-+ * attr->read() again passing that buffer as an argument.
-+ * Then we just copy to user-space using simple_read_from_buffer.
-+ */
-+
-+static ssize_t
-+configfs_read_bin_file(struct file *file, char __user *buf,
-+ size_t count, loff_t *ppos)
-+{
-+ struct configfs_buffer *buffer = file->private_data;
-+ struct dentry *dentry = file->f_path.dentry;
-+ struct config_item *item = to_item(dentry->d_parent);
-+ struct configfs_bin_attribute *bin_attr = to_bin_attr(dentry);
-+ ssize_t retval = 0;
-+ ssize_t len = min_t(size_t, count, PAGE_SIZE);
-+
-+ mutex_lock(&buffer->mutex);
-+
-+ /* we don't support switching read/write modes */
-+ if (buffer->write_in_progress) {
-+ retval = -ETXTBSY;
-+ goto out;
-+ }
-+ buffer->read_in_progress = 1;
-+
-+ if (buffer->needs_read_fill) {
-+ /* perform first read with buf == NULL to get extent */
-+ len = bin_attr->read(item, NULL, 0);
-+ if (len <= 0) {
-+ retval = len;
-+ goto out;
-+ }
-+
-+ /* do not exceed the maximum value */
-+ if (bin_attr->cb_max_size && len > bin_attr->cb_max_size) {
-+ retval = -EFBIG;
-+ goto out;
-+ }
-+
-+ buffer->bin_buffer = vmalloc(len);
-+ if (buffer->bin_buffer == NULL) {
-+ retval = -ENOMEM;
-+ goto out;
-+ }
-+ buffer->bin_buffer_size = len;
-+
-+ /* perform second read to fill buffer */
-+ len = bin_attr->read(item, buffer->bin_buffer, len);
-+ if (len < 0) {
-+ retval = len;
-+ vfree(buffer->bin_buffer);
-+ buffer->bin_buffer_size = 0;
-+ buffer->bin_buffer = NULL;
-+ goto out;
-+ }
-+
-+ buffer->needs_read_fill = 0;
-+ }
-+
-+ retval = simple_read_from_buffer(buf, count, ppos, buffer->bin_buffer,
-+ buffer->bin_buffer_size);
-+out:
-+ mutex_unlock(&buffer->mutex);
-+ return retval;
-+}
-+
-
- /**
- * fill_write_buffer - copy buffer from userspace.
-@@ -209,10 +295,80 @@ configfs_write_file(struct file *file, c
- return len;
- }
-
--static int check_perm(struct inode * inode, struct file * file)
-+/**
-+ * configfs_write_bin_file - write a binary attribute.
-+ * @file: file pointer
-+ * @buf: data to write
-+ * @count: number of bytes
-+ * @ppos: starting offset
-+ *
-+ * Writing to a binary attribute file is similar to a normal read.
-+ * We buffer the consecutive writes (binary attribute files do not
-+ * support lseek) in a continuously growing buffer, but we don't
-+ * commit until the close of the file.
-+ */
-+
-+static ssize_t
-+configfs_write_bin_file(struct file *file, const char __user *buf,
-+ size_t count, loff_t *ppos)
-+{
-+ struct configfs_buffer *buffer = file->private_data;
-+ struct dentry *dentry = file->f_path.dentry;
-+ struct configfs_bin_attribute *bin_attr = to_bin_attr(dentry);
-+ void *tbuf = NULL;
-+ ssize_t len;
-+
-+ mutex_lock(&buffer->mutex);
-+
-+ /* we don't support switching read/write modes */
-+ if (buffer->read_in_progress) {
-+ len = -ETXTBSY;
-+ goto out;
-+ }
-+ buffer->write_in_progress = 1;
-+
-+ /* buffer grows? */
-+ if (*ppos + count > buffer->bin_buffer_size) {
-+
-+ if (bin_attr->cb_max_size &&
-+ *ppos + count > bin_attr->cb_max_size) {
-+ len = -EFBIG;
-+ }
-+
-+ tbuf = vmalloc(*ppos + count);
-+ if (tbuf == NULL) {
-+ len = -ENOMEM;
-+ goto out;
-+ }
-+
-+ /* copy old contents */
-+ if (buffer->bin_buffer) {
-+ memcpy(tbuf, buffer->bin_buffer,
-+ buffer->bin_buffer_size);
-+ vfree(buffer->bin_buffer);
-+ }
-+
-+ /* clear the new area */
-+ memset(tbuf + buffer->bin_buffer_size, 0,
-+ *ppos + count - buffer->bin_buffer_size);
-+ buffer->bin_buffer = tbuf;
-+ buffer->bin_buffer_size = *ppos + count;
-+ }
-+
-+ len = simple_write_to_buffer(buffer->bin_buffer,
-+ buffer->bin_buffer_size, ppos, buf, count);
-+ if (len > 0)
-+ *ppos += len;
-+out:
-+ mutex_unlock(&buffer->mutex);
-+ return len;
-+}
-+
-+static int check_perm(struct inode * inode, struct file * file, int type)
- {
- struct config_item *item = configfs_get_config_item(file->f_path.dentry->d_parent);
- struct configfs_attribute * attr = to_attr(file->f_path.dentry);
-+ struct configfs_bin_attribute *bin_attr = NULL;
- struct configfs_buffer * buffer;
- struct configfs_item_operations * ops = NULL;
- int error = 0;
-@@ -220,6 +376,9 @@ static int check_perm(struct inode * ino
- if (!item || !attr)
- goto Einval;
-
-+ if (type & CONFIGFS_ITEM_BIN_ATTR)
-+ bin_attr = to_bin_attr(file->f_path.dentry);
-+
- /* Grab the module reference for this attribute if we have one */
- if (!try_module_get(attr->ca_owner)) {
- error = -ENODEV;
-@@ -236,9 +395,14 @@ static int check_perm(struct inode * ino
- * and we must have a store method.
- */
- if (file->f_mode & FMODE_WRITE) {
-- if (!(inode->i_mode & S_IWUGO) || !attr->store)
-+ if (!(inode->i_mode & S_IWUGO))
- goto Eaccess;
-
-+ if ((type & CONFIGFS_ITEM_ATTR) && !attr->store)
-+ goto Eaccess;
-+
-+ if ((type & CONFIGFS_ITEM_BIN_ATTR) && !bin_attr->write)
-+ goto Eaccess;
- }
-
- /* File needs read support.
-@@ -246,7 +410,13 @@ static int check_perm(struct inode * ino
- * must be a show method for it.
- */
- if (file->f_mode & FMODE_READ) {
-- if (!(inode->i_mode & S_IRUGO) || !attr->show)
-+ if (!(inode->i_mode & S_IRUGO))
-+ goto Eaccess;
-+
-+ if ((type & CONFIGFS_ITEM_ATTR) && !attr->show)
-+ goto Eaccess;
-+
-+ if ((type & CONFIGFS_ITEM_BIN_ATTR) && !bin_attr->read)
- goto Eaccess;
- }
-
-@@ -260,6 +430,8 @@ static int check_perm(struct inode * ino
- }
- mutex_init(&buffer->mutex);
- buffer->needs_read_fill = 1;
-+ buffer->read_in_progress = 0;
-+ buffer->write_in_progress = 0;
- buffer->ops = ops;
- file->private_data = buffer;
- goto Done;
-@@ -277,12 +449,7 @@ static int check_perm(struct inode * ino
- return error;
- }
-
--static int configfs_open_file(struct inode * inode, struct file * filp)
--{
-- return check_perm(inode,filp);
--}
--
--static int configfs_release(struct inode * inode, struct file * filp)
-+static int configfs_release(struct inode *inode, struct file *filp)
- {
- struct config_item * item = to_item(filp->f_path.dentry->d_parent);
- struct configfs_attribute * attr = to_attr(filp->f_path.dentry);
-@@ -303,6 +470,47 @@ static int configfs_release(struct inode
- return 0;
- }
-
-+static int configfs_open_file(struct inode *inode, struct file *filp)
-+{
-+ return check_perm(inode, filp, CONFIGFS_ITEM_ATTR);
-+}
-+
-+static int configfs_open_bin_file(struct inode *inode, struct file *filp)
-+{
-+ return check_perm(inode, filp, CONFIGFS_ITEM_BIN_ATTR);
-+}
-+
-+static int configfs_release_bin_file(struct inode *inode, struct file *filp)
-+{
-+ struct configfs_buffer *buffer = filp->private_data;
-+ struct dentry *dentry = filp->f_path.dentry;
-+ struct config_item *item = to_item(dentry->d_parent);
-+ struct configfs_bin_attribute *bin_attr = to_bin_attr(dentry);
-+ ssize_t len = 0;
-+ int ret;
-+
-+ buffer->read_in_progress = 0;
-+
-+ if (buffer->write_in_progress) {
-+ buffer->write_in_progress = 0;
-+
-+ len = bin_attr->write(item, buffer->bin_buffer,
-+ buffer->bin_buffer_size);
-+
-+ /* vfree on NULL is safe */
-+ vfree(buffer->bin_buffer);
-+ buffer->bin_buffer = NULL;
-+ buffer->bin_buffer_size = 0;
-+ buffer->needs_read_fill = 1;
-+ }
-+
-+ ret = configfs_release(inode, filp);
-+ if (len < 0)
-+ return len;
-+ return ret;
-+}
-+
-+
- const struct file_operations configfs_file_operations = {
- .read = configfs_read_file,
- .write = configfs_write_file,
-@@ -311,6 +519,14 @@ const struct file_operations configfs_fi
- .release = configfs_release,
- };
-
-+const struct file_operations configfs_bin_file_operations = {
-+ .read = configfs_read_bin_file,
-+ .write = configfs_write_bin_file,
-+ .llseek = NULL, /* bin file is not seekable */
-+ .open = configfs_open_bin_file,
-+ .release = configfs_release_bin_file,
-+};
-+
- /**
- * configfs_create_file - create an attribute file for an item.
- * @item: item we're creating for.
-@@ -332,3 +548,24 @@ int configfs_create_file(struct config_i
- return error;
- }
-
-+/**
-+ * configfs_create_bin_file - create a binary attribute file for an item.
-+ * @item: item we're creating for.
-+ * @attr: atrribute descriptor.
-+ */
-+
-+int configfs_create_bin_file(struct config_item *item,
-+ const struct configfs_bin_attribute *bin_attr)
-+{
-+ struct dentry *dir = item->ci_dentry;
-+ struct configfs_dirent *parent_sd = dir->d_fsdata;
-+ umode_t mode = (bin_attr->cb_attr.ca_mode & S_IALLUGO) | S_IFREG;
-+ int error = 0;
-+
-+ mutex_lock_nested(&dir->d_inode->i_mutex, I_MUTEX_NORMAL);
-+ error = configfs_make_dirent(parent_sd, NULL, (void *) bin_attr, mode,
-+ CONFIGFS_ITEM_BIN_ATTR);
-+ mutex_unlock(&dir->d_inode->i_mutex);
-+
-+ return error;
-+}
---- a/fs/configfs/inode.c
-+++ b/fs/configfs/inode.c
-@@ -218,7 +218,7 @@ const unsigned char * configfs_get_name(
- if (sd->s_type & (CONFIGFS_DIR | CONFIGFS_ITEM_LINK))
- return sd->s_dentry->d_name.name;
-
-- if (sd->s_type & CONFIGFS_ITEM_ATTR) {
-+ if (sd->s_type & (CONFIGFS_ITEM_ATTR | CONFIGFS_ITEM_BIN_ATTR)) {
- attr = sd->s_element;
- return attr->ca_name;
- }
---- a/include/linux/configfs.h
-+++ b/include/linux/configfs.h
-@@ -51,6 +51,7 @@ struct module;
- struct configfs_item_operations;
- struct configfs_group_operations;
- struct configfs_attribute;
-+struct configfs_bin_attribute;
- struct configfs_subsystem;
-
- struct config_item {
-@@ -84,6 +85,7 @@ struct config_item_type {
- struct configfs_item_operations *ct_item_ops;
- struct configfs_group_operations *ct_group_ops;
- struct configfs_attribute **ct_attrs;
-+ struct configfs_bin_attribute **ct_bin_attrs;
- };
-
- /**
-@@ -154,6 +156,54 @@ static struct configfs_attribute _pfx##a
- .store = _pfx##_name##_store, \
- }
-
-+struct file;
-+struct vm_area_struct;
-+
-+struct configfs_bin_attribute {
-+ struct configfs_attribute cb_attr; /* std. attribute */
-+ void *cb_private; /* for user */
-+ size_t cb_max_size; /* max core size */
-+ ssize_t (*read)(struct config_item *, void *, size_t);
-+ ssize_t (*write)(struct config_item *, const void *, size_t);
-+};
-+
-+#define CONFIGFS_BIN_ATTR(_pfx, _name, _priv, _maxsz) \
-+static struct configfs_bin_attribute _pfx##attr_##_name = { \
-+ .cb_attr = { \
-+ .ca_name = __stringify(_name), \
-+ .ca_mode = S_IRUGO | S_IWUSR, \
-+ .ca_owner = THIS_MODULE, \
-+ }, \
-+ .cb_private = _priv, \
-+ .cb_max_size = _maxsz, \
-+ .read = _pfx##_name##_read, \
-+ .write = _pfx##_name##_write, \
-+}
-+
-+#define CONFIGFS_BIN_ATTR_RO(_pfx, _name, _priv, _maxsz) \
-+static struct configfs_attribute _pfx##attr_##_name = { \
-+ .cb_attr = { \
-+ .ca_name = __stringify(_name), \
-+ .ca_mode = S_IRUGO, \
-+ .ca_owner = THIS_MODULE, \
-+ }, \
-+ .cb_private = _priv, \
-+ .cb_max_size = _maxsz, \
-+ .read = _pfx##_name##_read, \
-+}
-+
-+#define CONFIGFS_BIN_ATTR_WO(_pfx, _name, _priv, _maxsz) \
-+static struct configfs_attribute _pfx##attr_##_name = { \
-+ .cb_attr = { \
-+ .ca_name = __stringify(_name), \
-+ .ca_mode = S_IWUSR, \
-+ .ca_owner = THIS_MODULE, \
-+ }, \
-+ .cb_private = _priv, \
-+ .cb_max_size = _maxsz, \
-+ .write = _pfx##_name##_write, \
-+}
-+
- /*
- * If allow_link() exists, the item can symlink(2) out to other
- * items. If the item is a group, it may support mkdir(2).
diff --git a/target/linux/brcm2708/patches-4.4/0178-OF-DT-Overlay-configfs-interface.patch b/target/linux/brcm2708/patches-4.4/0178-OF-DT-Overlay-configfs-interface.patch
deleted file mode 100644
index bfa6e65..0000000
--- a/target/linux/brcm2708/patches-4.4/0178-OF-DT-Overlay-configfs-interface.patch
+++ /dev/null
@@ -1,408 +0,0 @@
-From a21871b24d8f33c80a3ed5bee23fac981d4bdbe8 Mon Sep 17 00:00:00 2001
-From: Pantelis Antoniou <pantelis.antoniou at konsulko.com>
-Date: Wed, 3 Dec 2014 13:23:28 +0200
-Subject: [PATCH] OF: DT-Overlay configfs interface
-
-This is a port of Pantelis Antoniou's v3 port that makes use of the
-new upstreamed configfs support for binary attributes.
-
-Original commit message:
-
-Add a runtime interface to using configfs for generic device tree overlay
-usage. With it its possible to use device tree overlays without having
-to use a per-platform overlay manager.
-
-Please see Documentation/devicetree/configfs-overlays.txt for more info.
-
-Changes since v2:
-- Removed ifdef CONFIG_OF_OVERLAY (since for now it's required)
-- Created a documentation entry
-- Slight rewording in Kconfig
-
-Changes since v1:
-- of_resolve() -> of_resolve_phandles().
-
-Originally-signed-off-by: Pantelis Antoniou <pantelis.antoniou at konsulko.com>
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- Documentation/devicetree/configfs-overlays.txt | 31 +++
- drivers/of/Kconfig | 7 +
- drivers/of/Makefile | 1 +
- drivers/of/configfs.c | 314 +++++++++++++++++++++++++
- 4 files changed, 353 insertions(+)
- create mode 100644 Documentation/devicetree/configfs-overlays.txt
- create mode 100644 drivers/of/configfs.c
-
---- /dev/null
-+++ b/Documentation/devicetree/configfs-overlays.txt
-@@ -0,0 +1,31 @@
-+Howto use the configfs overlay interface.
-+
-+A device-tree configfs entry is created in /config/device-tree/overlays
-+and and it is manipulated using standard file system I/O.
-+Note that this is a debug level interface, for use by developers and
-+not necessarily something accessed by normal users due to the
-+security implications of having direct access to the kernel's device tree.
-+
-+* To create an overlay you mkdir the directory:
-+
-+ # mkdir /config/device-tree/overlays/foo
-+
-+* Either you echo the overlay firmware file to the path property file.
-+
-+ # echo foo.dtbo >/config/device-tree/overlays/foo/path
-+
-+* Or you cat the contents of the overlay to the dtbo file
-+
-+ # cat foo.dtbo >/config/device-tree/overlays/foo/dtbo
-+
-+The overlay file will be applied, and devices will be created/destroyed
-+as required.
-+
-+To remove it simply rmdir the directory.
-+
-+ # rmdir /config/device-tree/overlays/foo
-+
-+The rationalle of the dual interface (firmware & direct copy) is that each is
-+better suited to different use patterns. The firmware interface is what's
-+intended to be used by hardware managers in the kernel, while the copy interface
-+make sense for developers (since it avoids problems with namespaces).
---- a/drivers/of/Kconfig
-+++ b/drivers/of/Kconfig
-@@ -112,4 +112,11 @@ config OF_OVERLAY
- While this option is selected automatically when needed, you can
- enable it manually to improve device tree unit test coverage.
-
-+config OF_CONFIGFS
-+ bool "Device Tree Overlay ConfigFS interface"
-+ select CONFIGFS_FS
-+ select OF_OVERLAY
-+ help
-+ Enable a simple user-space driven DT overlay interface.
-+
- endif # OF
---- a/drivers/of/Makefile
-+++ b/drivers/of/Makefile
-@@ -1,4 +1,5 @@
- obj-y = base.o device.o platform.o
-+obj-$(CONFIG_OF_CONFIGFS) += configfs.o
- obj-$(CONFIG_OF_DYNAMIC) += dynamic.o
- obj-$(CONFIG_OF_FLATTREE) += fdt.o
- obj-$(CONFIG_OF_EARLY_FLATTREE) += fdt_address.o
---- /dev/null
-+++ b/drivers/of/configfs.c
-@@ -0,0 +1,314 @@
-+/*
-+ * Configfs entries for device-tree
-+ *
-+ * Copyright (C) 2013 - Pantelis Antoniou <panto at antoniou-consulting.com>
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * as published by the Free Software Foundation; either version
-+ * 2 of the License, or (at your option) any later version.
-+ */
-+#include <linux/ctype.h>
-+#include <linux/cpu.h>
-+#include <linux/module.h>
-+#include <linux/of.h>
-+#include <linux/of_fdt.h>
-+#include <linux/spinlock.h>
-+#include <linux/slab.h>
-+#include <linux/proc_fs.h>
-+#include <linux/configfs.h>
-+#include <linux/types.h>
-+#include <linux/stat.h>
-+#include <linux/limits.h>
-+#include <linux/file.h>
-+#include <linux/vmalloc.h>
-+#include <linux/firmware.h>
-+
-+#include "of_private.h"
-+
-+struct cfs_overlay_item {
-+ struct config_item item;
-+
-+ char path[PATH_MAX];
-+
-+ const struct firmware *fw;
-+ struct device_node *overlay;
-+ int ov_id;
-+
-+ void *dtbo;
-+ int dtbo_size;
-+};
-+
-+static int create_overlay(struct cfs_overlay_item *overlay, void *blob)
-+{
-+ int err;
-+
-+ /* unflatten the tree */
-+ of_fdt_unflatten_tree(blob, &overlay->overlay);
-+ if (overlay->overlay == NULL) {
-+ pr_err("%s: failed to unflatten tree\n", __func__);
-+ err = -EINVAL;
-+ goto out_err;
-+ }
-+ pr_debug("%s: unflattened OK\n", __func__);
-+
-+ /* mark it as detached */
-+ of_node_set_flag(overlay->overlay, OF_DETACHED);
-+
-+ /* perform resolution */
-+ err = of_resolve_phandles(overlay->overlay);
-+ if (err != 0) {
-+ pr_err("%s: Failed to resolve tree\n", __func__);
-+ goto out_err;
-+ }
-+ pr_debug("%s: resolved OK\n", __func__);
-+
-+ err = of_overlay_create(overlay->overlay);
-+ if (err < 0) {
-+ pr_err("%s: Failed to create overlay (err=%d)\n",
-+ __func__, err);
-+ goto out_err;
-+ }
-+ overlay->ov_id = err;
-+
-+out_err:
-+ return err;
-+}
-+
-+static inline struct cfs_overlay_item *to_cfs_overlay_item(
-+ struct config_item *item)
-+{
-+ return item ? container_of(item, struct cfs_overlay_item, item) : NULL;
-+}
-+
-+static ssize_t cfs_overlay_item_path_show(struct config_item *item,
-+ char *page)
-+{
-+ struct cfs_overlay_item *overlay = to_cfs_overlay_item(item);
-+ return sprintf(page, "%s\n", overlay->path);
-+}
-+
-+static ssize_t cfs_overlay_item_path_store(struct config_item *item,
-+ const char *page, size_t count)
-+{
-+ struct cfs_overlay_item *overlay = to_cfs_overlay_item(item);
-+ const char *p = page;
-+ char *s;
-+ int err;
-+
-+ /* if it's set do not allow changes */
-+ if (overlay->path[0] != '\0' || overlay->dtbo_size > 0)
-+ return -EPERM;
-+
-+ /* copy to path buffer (and make sure it's always zero terminated */
-+ count = snprintf(overlay->path, sizeof(overlay->path) - 1, "%s", p);
-+ overlay->path[sizeof(overlay->path) - 1] = '\0';
-+
-+ /* strip trailing newlines */
-+ s = overlay->path + strlen(overlay->path);
-+ while (s > overlay->path && *--s == '\n')
-+ *s = '\0';
-+
-+ pr_debug("%s: path is '%s'\n", __func__, overlay->path);
-+
-+ err = request_firmware(&overlay->fw, overlay->path, NULL);
-+ if (err != 0)
-+ goto out_err;
-+
-+ err = create_overlay(overlay, (void *)overlay->fw->data);
-+ if (err != 0)
-+ goto out_err;
-+
-+ return count;
-+
-+out_err:
-+
-+ release_firmware(overlay->fw);
-+ overlay->fw = NULL;
-+
-+ overlay->path[0] = '\0';
-+ return err;
-+}
-+
-+static ssize_t cfs_overlay_item_status_show(struct config_item *item,
-+ char *page)
-+{
-+ struct cfs_overlay_item *overlay = to_cfs_overlay_item(item);
-+
-+ return sprintf(page, "%s\n",
-+ overlay->ov_id >= 0 ? "applied" : "unapplied");
-+}
-+
-+CONFIGFS_ATTR(cfs_overlay_item_, path);
-+CONFIGFS_ATTR_RO(cfs_overlay_item_, status);
-+
-+static struct configfs_attribute *cfs_overlay_attrs[] = {
-+ &cfs_overlay_item_attr_path,
-+ &cfs_overlay_item_attr_status,
-+ NULL,
-+};
-+
-+ssize_t cfs_overlay_item_dtbo_read(struct config_item *item,
-+ void *buf, size_t max_count)
-+{
-+ struct cfs_overlay_item *overlay = to_cfs_overlay_item(item);
-+
-+ pr_debug("%s: buf=%p max_count=%u\n", __func__,
-+ buf, max_count);
-+
-+ if (overlay->dtbo == NULL)
-+ return 0;
-+
-+ /* copy if buffer provided */
-+ if (buf != NULL) {
-+ /* the buffer must be large enough */
-+ if (overlay->dtbo_size > max_count)
-+ return -ENOSPC;
-+
-+ memcpy(buf, overlay->dtbo, overlay->dtbo_size);
-+ }
-+
-+ return overlay->dtbo_size;
-+}
-+
-+ssize_t cfs_overlay_item_dtbo_write(struct config_item *item,
-+ const void *buf, size_t count)
-+{
-+ struct cfs_overlay_item *overlay = to_cfs_overlay_item(item);
-+ int err;
-+
-+ /* if it's set do not allow changes */
-+ if (overlay->path[0] != '\0' || overlay->dtbo_size > 0)
-+ return -EPERM;
-+
-+ /* copy the contents */
-+ overlay->dtbo = kmemdup(buf, count, GFP_KERNEL);
-+ if (overlay->dtbo == NULL)
-+ return -ENOMEM;
-+
-+ overlay->dtbo_size = count;
-+
-+ err = create_overlay(overlay, overlay->dtbo);
-+ if (err != 0)
-+ goto out_err;
-+
-+ return count;
-+
-+out_err:
-+ kfree(overlay->dtbo);
-+ overlay->dtbo = NULL;
-+ overlay->dtbo_size = 0;
-+
-+ return err;
-+}
-+
-+CONFIGFS_BIN_ATTR(cfs_overlay_item_, dtbo, NULL, SZ_1M);
-+
-+static struct configfs_bin_attribute *cfs_overlay_bin_attrs[] = {
-+ &cfs_overlay_item_attr_dtbo,
-+ NULL,
-+};
-+
-+static void cfs_overlay_release(struct config_item *item)
-+{
-+ struct cfs_overlay_item *overlay = to_cfs_overlay_item(item);
-+
-+ if (overlay->ov_id >= 0)
-+ of_overlay_destroy(overlay->ov_id);
-+ if (overlay->fw)
-+ release_firmware(overlay->fw);
-+ /* kfree with NULL is safe */
-+ kfree(overlay->dtbo);
-+ kfree(overlay);
-+}
-+
-+static struct configfs_item_operations cfs_overlay_item_ops = {
-+ .release = cfs_overlay_release,
-+};
-+
-+static struct config_item_type cfs_overlay_type = {
-+ .ct_item_ops = &cfs_overlay_item_ops,
-+ .ct_attrs = cfs_overlay_attrs,
-+ .ct_bin_attrs = cfs_overlay_bin_attrs,
-+ .ct_owner = THIS_MODULE,
-+};
-+
-+static struct config_item *cfs_overlay_group_make_item(
-+ struct config_group *group, const char *name)
-+{
-+ struct cfs_overlay_item *overlay;
-+
-+ overlay = kzalloc(sizeof(*overlay), GFP_KERNEL);
-+ if (!overlay)
-+ return ERR_PTR(-ENOMEM);
-+ overlay->ov_id = -1;
-+
-+ config_item_init_type_name(&overlay->item, name, &cfs_overlay_type);
-+ return &overlay->item;
-+}
-+
-+static void cfs_overlay_group_drop_item(struct config_group *group,
-+ struct config_item *item)
-+{
-+ struct cfs_overlay_item *overlay = to_cfs_overlay_item(item);
-+
-+ config_item_put(&overlay->item);
-+}
-+
-+static struct configfs_group_operations overlays_ops = {
-+ .make_item = cfs_overlay_group_make_item,
-+ .drop_item = cfs_overlay_group_drop_item,
-+};
-+
-+static struct config_item_type overlays_type = {
-+ .ct_group_ops = &overlays_ops,
-+ .ct_owner = THIS_MODULE,
-+};
-+
-+static struct configfs_group_operations of_cfs_ops = {
-+ /* empty - we don't allow anything to be created */
-+};
-+
-+static struct config_item_type of_cfs_type = {
-+ .ct_group_ops = &of_cfs_ops,
-+ .ct_owner = THIS_MODULE,
-+};
-+
-+struct config_group of_cfs_overlay_group;
-+
-+struct config_group *of_cfs_def_groups[] = {
-+ &of_cfs_overlay_group,
-+ NULL
-+};
-+
-+static struct configfs_subsystem of_cfs_subsys = {
-+ .su_group = {
-+ .cg_item = {
-+ .ci_namebuf = "device-tree",
-+ .ci_type = &of_cfs_type,
-+ },
-+ .default_groups = of_cfs_def_groups,
-+ },
-+ .su_mutex = __MUTEX_INITIALIZER(of_cfs_subsys.su_mutex),
-+};
-+
-+static int __init of_cfs_init(void)
-+{
-+ int ret;
-+
-+ pr_info("%s\n", __func__);
-+
-+ config_group_init(&of_cfs_subsys.su_group);
-+ config_group_init_type_name(&of_cfs_overlay_group, "overlays",
-+ &overlays_type);
-+
-+ ret = configfs_register_subsystem(&of_cfs_subsys);
-+ if (ret != 0) {
-+ pr_err("%s: failed to register subsys\n", __func__);
-+ goto out;
-+ }
-+ pr_info("%s: OK\n", __func__);
-+out:
-+ return ret;
-+}
-+late_initcall(of_cfs_init);
diff --git a/target/linux/brcm2708/patches-4.4/0179-Protect-__release_resource-against-resources-without.patch b/target/linux/brcm2708/patches-4.4/0179-Protect-__release_resource-against-resources-without.patch
deleted file mode 100644
index 4122413..0000000
--- a/target/linux/brcm2708/patches-4.4/0179-Protect-__release_resource-against-resources-without.patch
+++ /dev/null
@@ -1,27 +0,0 @@
-From 290f9608c2a1294033a3fa6c6c9f842313ae874a Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 13 Mar 2015 12:43:36 +0000
-Subject: [PATCH] Protect __release_resource against resources without parents
-
-Without this patch, removing a device tree overlay can crash here.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- kernel/resource.c | 6 ++++++
- 1 file changed, 6 insertions(+)
-
---- a/kernel/resource.c
-+++ b/kernel/resource.c
-@@ -237,6 +237,12 @@ static int __release_resource(struct res
- {
- struct resource *tmp, **p;
-
-+ if (!old->parent) {
-+ WARN(old->sibling, "sibling but no parent");
-+ if (old->sibling)
-+ return -EINVAL;
-+ return 0;
-+ }
- p = &old->parent->child;
- for (;;) {
- tmp = *p;
diff --git a/target/linux/brcm2708/patches-4.4/0180-BCM270X_DT-Add-a-.dtbo-target-use-for-overlays.patch b/target/linux/brcm2708/patches-4.4/0180-BCM270X_DT-Add-a-.dtbo-target-use-for-overlays.patch
deleted file mode 100644
index 8ac5c3a..0000000
--- a/target/linux/brcm2708/patches-4.4/0180-BCM270X_DT-Add-a-.dtbo-target-use-for-overlays.patch
+++ /dev/null
@@ -1,193 +0,0 @@
-From 4ac5a040374bae6eb55efeab8b15f2b5dc379e06 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 13 Mar 2015 20:00:21 +0000
-Subject: [PATCH] BCM270X_DT: Add a .dtbo target, use for overlays
-
-Change the filenames and extensions to keep the pre-DDT style of
-overlay (<name>-overlay.dtb) distinct from new ones that use a
-different style of local fixups (<name>.dtbo), and to match other
-platforms.
-
-The RPi firmware uses the DDTK trailer atom to choose which type of
-overlay to use for each kernel.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/.gitignore | 2 +-
- arch/arm/boot/dts/overlays/Makefile | 135 +++++++++++++++++-------------------
- scripts/Makefile.lib | 10 +++
- 3 files changed, 76 insertions(+), 71 deletions(-)
-
---- a/arch/arm/boot/.gitignore
-+++ b/arch/arm/boot/.gitignore
-@@ -3,4 +3,4 @@ zImage
- xipImage
- bootpImage
- uImage
--*.dtb
-+*.dtb*
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -12,78 +12,73 @@ ifeq ($(CONFIG_ARCH_BCM2835),y)
- RPI_DT_OVERLAYS=y
- endif
-
--dtb-$(RPI_DT_OVERLAYS) += ads7846-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += at86rf233-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += bmp085_i2c-sensor-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += dwc2-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += dwc-otg-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += dht11-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += enc28j60-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += gpio-ir-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += gpio-poweroff-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += hifiberry-amp-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += hifiberry-dac-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += hifiberry-dacplus-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += hifiberry-digi-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += hy28a-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += hy28b-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += i2c-rtc-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += i2c-gpio-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += i2c0-bcm2708-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += i2c1-bcm2708-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += i2s-mmap-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += iqaudio-dac-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += iqaudio-dacplus-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += lirc-rpi-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += mcp2515-can0-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += mcp2515-can1-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += mmc-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += mz61581-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += pi3-disable-bt-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += pi3-miniuart-bt-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += piscreen-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += piscreen2r-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += pitft28-capacitive-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += pitft28-resistive-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += pps-gpio-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += pwm-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += pwm-2chan-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += raspidac3-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += rpi-backlight-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += rpi-dac-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += rpi-display-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += rpi-ft5406-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += rpi-proto-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += rpi-sense-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += sdhost-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += sdio-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += sdtweak-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += smi-dev-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += smi-nand-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += smi-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += spi1-1cs-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += spi1-2cs-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += spi1-3cs-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += spi2-1cs-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += spi2-2cs-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += spi2-3cs-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += spi-gpio35-39-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += tinylcd35-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += uart1-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += vc4-kms-v3d-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += vga666-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += w1-gpio-overlay.dtb
--dtb-$(RPI_DT_OVERLAYS) += w1-gpio-pullup-overlay.dtb
-+dtbo-$(RPI_DT_OVERLAYS) += ads7846.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += at86rf233.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += bmp085_i2c-sensor.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += dwc2.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += dwc-otg.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += dht11.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += enc28j60.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += gpio-ir.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += gpio-poweroff.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += hifiberry-amp.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += hifiberry-dac.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += hifiberry-dacplus.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += hifiberry-digi.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += hy28a.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += hy28b.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += i2c-rtc.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += i2c-gpio.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += i2c0-bcm2708.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += i2c1-bcm2708.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += i2s-mmap.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += iqaudio-dac.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += iqaudio-dacplus.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += lirc-rpi.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += mcp2515-can0.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += mcp2515-can1.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += mmc.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += mz61581.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += pi3-disable-bt.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += pi3-miniuart-bt.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += piscreen.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += piscreen2r.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += pitft28-capacitive.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += pitft28-resistive.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += pps-gpio.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += pwm.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += pwm-2chan.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += raspidac3.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += rpi-backlight.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += rpi-dac.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += rpi-display.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += rpi-ft5406.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += rpi-proto.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += rpi-sense.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += sdhost.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += sdio.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += sdtweak.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += smi-dev.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += smi-nand.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += smi.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += spi1-1cs.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += spi1-2cs.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += spi1-3cs.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += spi2-1cs.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += spi2-2cs.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += spi2-3cs.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += spi-gpio35-39.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += tinylcd35.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += uart1.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += vc4-kms-v3d.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += vga666.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += w1-gpio.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += w1-gpio-pullup.dtbo
-
- targets += dtbs dtbs_install
--targets += $(dtb-y)
-+targets += $(dtbo-y)
-
- endif
-
--always := $(dtb-y)
--clean-files := *.dtb
--
--# Enable fixups to support overlays on BCM2708 platforms
--ifeq ($(RPI_DT_OVERLAYS),y)
-- DTC_FLAGS ?= -@
--endif
-+always := $(dtbo-y)
-+clean-files := *.dtbo
---- a/scripts/Makefile.lib
-+++ b/scripts/Makefile.lib
-@@ -292,6 +292,16 @@ cmd_dtc = mkdir -p $(dir ${dtc-tmp}) ; \
- $(obj)/%.dtb: $(src)/%.dts FORCE
- $(call if_changed_dep,dtc)
-
-+quiet_cmd_dtco = DTCO $@
-+cmd_dtco = $(CPP) $(dtc_cpp_flags) -x assembler-with-cpp -o $(dtc-tmp) $< ; \
-+ $(objtree)/scripts/dtc/dtc -@ -O dtb -o $@ -b 0 \
-+ -i $(dir $<) $(DTC_FLAGS) \
-+ -d $(depfile).dtc.tmp $(dtc-tmp) ; \
-+ cat $(depfile).pre.tmp $(depfile).dtc.tmp > $(depfile)
-+
-+$(obj)/%.dtbo: $(src)/%-overlay.dts FORCE
-+ $(call if_changed_dep,dtco)
-+
- dtc-tmp = $(subst $(comma),_,$(dot-target).dts.tmp)
-
- # Bzip2
diff --git a/target/linux/brcm2708/patches-4.4/0181-scripts-knlinfo-Decode-DDTK-atom.patch b/target/linux/brcm2708/patches-4.4/0181-scripts-knlinfo-Decode-DDTK-atom.patch
deleted file mode 100644
index 6da6cf0..0000000
--- a/target/linux/brcm2708/patches-4.4/0181-scripts-knlinfo-Decode-DDTK-atom.patch
+++ /dev/null
@@ -1,31 +0,0 @@
-From 923637607b454c86216da7e2eedcb23731ebeb24 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 29 May 2015 11:18:58 +0100
-Subject: [PATCH] scripts/knlinfo: Decode DDTK atom
-
-Show the DDTK atom as being a boolean.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- scripts/knlinfo | 3 ++-
- 1 file changed, 2 insertions(+), 1 deletion(-)
-
---- a/scripts/knlinfo
-+++ b/scripts/knlinfo
-@@ -16,6 +16,7 @@ my $trailer_magic = 'RPTL';
-
- my %atom_formats =
- (
-+ 'DDTK' => \&format_bool,
- 'DTOK' => \&format_bool,
- 'KVer' => \&format_string,
- '270X' => \&format_bool,
-@@ -148,7 +149,7 @@ sub format_atom
- sub format_bool
- {
- my ($data) = @_;
-- return unpack('V', $data) ? 'true' : 'false';
-+ return unpack('V', $data) ? 'y' : 'n';
- }
-
- sub format_int
diff --git a/target/linux/brcm2708/patches-4.4/0182-Enable-Dynamic-Device-Tree-for-bcmrpi_defconfig-and-.patch b/target/linux/brcm2708/patches-4.4/0182-Enable-Dynamic-Device-Tree-for-bcmrpi_defconfig-and-.patch
deleted file mode 100644
index b131bda..0000000
--- a/target/linux/brcm2708/patches-4.4/0182-Enable-Dynamic-Device-Tree-for-bcmrpi_defconfig-and-.patch
+++ /dev/null
@@ -1,40 +0,0 @@
-From eed86699379c418216242680e285eeb393ec055b Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 29 May 2015 11:48:59 +0100
-Subject: [PATCH] Enable Dynamic Device Tree for bcmrpi_defconfig and
- bcm2709_defconfig
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/configs/bcm2709_defconfig | 2 +-
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 2 files changed, 2 insertions(+), 1 deletion(-)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -403,6 +403,7 @@ CONFIG_MTD=m
- CONFIG_MTD_BLOCK=m
- CONFIG_MTD_NAND=m
- CONFIG_MTD_UBI=m
-+CONFIG_OF_CONFIGFS=y
- CONFIG_ZRAM=m
- CONFIG_ZRAM_LZ4_COMPRESS=y
- CONFIG_BLK_DEV_LOOP=y
-@@ -1161,7 +1162,6 @@ CONFIG_NTFS_FS=m
- CONFIG_NTFS_RW=y
- CONFIG_TMPFS=y
- CONFIG_TMPFS_POSIX_ACL=y
--CONFIG_CONFIGFS_FS=y
- CONFIG_ECRYPT_FS=m
- CONFIG_HFS_FS=m
- CONFIG_HFSPLUS_FS=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -396,6 +396,7 @@ CONFIG_MTD=m
- CONFIG_MTD_BLOCK=m
- CONFIG_MTD_NAND=m
- CONFIG_MTD_UBI=m
-+CONFIG_OF_OVERLAY=y
- CONFIG_ZRAM=m
- CONFIG_ZRAM_LZ4_COMPRESS=y
- CONFIG_BLK_DEV_LOOP=y
diff --git a/target/linux/brcm2708/patches-4.4/0183-SQUASH-Add-CONFIG_OF_CONFIGFS-to-bcmrpi_defconfig.patch b/target/linux/brcm2708/patches-4.4/0183-SQUASH-Add-CONFIG_OF_CONFIGFS-to-bcmrpi_defconfig.patch
deleted file mode 100644
index 49cbbd4..0000000
--- a/target/linux/brcm2708/patches-4.4/0183-SQUASH-Add-CONFIG_OF_CONFIGFS-to-bcmrpi_defconfig.patch
+++ /dev/null
@@ -1,29 +0,0 @@
-From 141144638ff113861764bf1bdff74ff31c042a87 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Sun, 13 Mar 2016 16:14:44 +0000
-Subject: [PATCH] SQUASH: Add CONFIG_OF_CONFIGFS to bcmrpi_defconfig
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/configs/bcmrpi_defconfig | 3 +--
- 1 file changed, 1 insertion(+), 2 deletions(-)
-
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -396,7 +396,7 @@ CONFIG_MTD=m
- CONFIG_MTD_BLOCK=m
- CONFIG_MTD_NAND=m
- CONFIG_MTD_UBI=m
--CONFIG_OF_OVERLAY=y
-+CONFIG_OF_CONFIGFS=y
- CONFIG_ZRAM=m
- CONFIG_ZRAM_LZ4_COMPRESS=y
- CONFIG_BLK_DEV_LOOP=y
-@@ -1169,7 +1169,6 @@ CONFIG_NTFS_FS=m
- CONFIG_NTFS_RW=y
- CONFIG_TMPFS=y
- CONFIG_TMPFS_POSIX_ACL=y
--CONFIG_CONFIGFS_FS=y
- CONFIG_ECRYPT_FS=m
- CONFIG_HFS_FS=m
- CONFIG_HFSPLUS_FS=m
diff --git a/target/linux/brcm2708/patches-4.4/0184-dts-kbuild-dtbs_install-installs-.dtbo-files-too.patch b/target/linux/brcm2708/patches-4.4/0184-dts-kbuild-dtbs_install-installs-.dtbo-files-too.patch
deleted file mode 100644
index 06153fb..0000000
--- a/target/linux/brcm2708/patches-4.4/0184-dts-kbuild-dtbs_install-installs-.dtbo-files-too.patch
+++ /dev/null
@@ -1,42 +0,0 @@
-From d38115727d4a75484aef19100578d0b1f3131f45 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 14 Mar 2016 16:56:54 +0000
-Subject: [PATCH] dts, kbuild: dtbs_install installs .dtbo files too
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- scripts/Makefile.dtbinst | 10 +++++++---
- 1 file changed, 7 insertions(+), 3 deletions(-)
-
---- a/scripts/Makefile.dtbinst
-+++ b/scripts/Makefile.dtbinst
-@@ -29,6 +29,7 @@ ifeq ("$(dtbinst-root)", "$(obj)")
- endif
-
- dtbinst-files := $(dtb-y)
-+dtboinst-files := $(dtbo-y)
- dtbinst-dirs := $(dts-dirs)
-
- # Helper targets for Installing DTBs into the boot directory
-@@ -37,15 +38,18 @@ quiet_cmd_dtb_install = INSTALL $<
-
- install-dir = $(patsubst $(dtbinst-root)%,$(INSTALL_DTBS_PATH)%,$(obj))
-
--$(dtbinst-files) $(dtbinst-dirs): | __dtbs_install_prep
-+$(dtbinst-files) $(dtboinst-files) $(dtbinst-dirs): | __dtbs_install_prep
-
- $(dtbinst-files): %.dtb: $(obj)/%.dtb
- $(call cmd,dtb_install,$(install-dir))
-
-+$(dtboinst-files): %.dtbo: $(obj)/%.dtbo
-+ $(call cmd,dtb_install,$(install-dir))
-+
- $(dtbinst-dirs):
- $(Q)$(MAKE) $(dtbinst)=$(obj)/$@
-
--PHONY += $(dtbinst-files) $(dtbinst-dirs)
--__dtbs_install: $(dtbinst-files) $(dtbinst-dirs)
-+PHONY += $(dtbinst-files) $(dtboinst-files) $(dtbinst-dirs)
-+__dtbs_install: $(dtbinst-files) $(dtboinst-files) $(dtbinst-dirs)
-
- .PHONY: $(PHONY)
diff --git a/target/linux/brcm2708/patches-4.4/0185-bcm2835-sdhost-Workaround-for-slow-sectors.patch b/target/linux/brcm2708/patches-4.4/0185-bcm2835-sdhost-Workaround-for-slow-sectors.patch
deleted file mode 100644
index 81abccd..0000000
--- a/target/linux/brcm2708/patches-4.4/0185-bcm2835-sdhost-Workaround-for-slow-sectors.patch
+++ /dev/null
@@ -1,118 +0,0 @@
-From d8b46a34e59ebee9ffa01a4b5bbe407351dff12d Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Tue, 15 Mar 2016 14:10:29 +0000
-Subject: [PATCH] bcm2835-sdhost: Workaround for "slow" sectors
-
-Some cards have been seen to cause timeouts after certain sectors are
-read. This workaround enforces a minimum delay between the stop after
-reading one of those sectors and a subsequent data command.
-
-Using CMD23 (SET_BLOCK_COUNT) avoids this problem, so good cards will
-not be penalised by this workaround.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- drivers/mmc/host/bcm2835-sdhost.c | 50 +++++++++++++++++++++++++++++++++++----
- 1 file changed, 46 insertions(+), 4 deletions(-)
-
---- a/drivers/mmc/host/bcm2835-sdhost.c
-+++ b/drivers/mmc/host/bcm2835-sdhost.c
-@@ -202,9 +202,12 @@ struct bcm2835_host {
- int max_delay; /* maximum length of time spent waiting */
- struct timeval stop_time; /* when the last stop was issued */
- u32 delay_after_stop; /* minimum time between stop and subsequent data transfer */
-+ u32 delay_after_this_stop; /* minimum time between this stop and subsequent data transfer */
- u32 overclock_50; /* frequency to use when 50MHz is requested (in MHz) */
- u32 overclock; /* Current frequency if overclocked, else zero */
- u32 pio_limit; /* Maximum block count for PIO (0 = always DMA) */
-+
-+ u32 sectors; /* Cached card size in sectors */
- };
-
- #if ENABLE_LOG
-@@ -425,6 +428,7 @@ static void bcm2835_sdhost_reset_interna
- bcm2835_sdhost_set_power(host, true);
- mdelay(10);
- host->clock = 0;
-+ host->sectors = 0;
- bcm2835_sdhost_write(host, host->hcfg, SDHCFG);
- bcm2835_sdhost_write(host, host->cdiv, SDCDIV);
- mmiowb();
-@@ -880,6 +884,24 @@ static void bcm2835_sdhost_prepare_data(
- host->flush_fifo = 0;
- host->data->bytes_xfered = 0;
-
-+ if (!host->sectors && host->mmc->card) {
-+ struct mmc_card *card = host->mmc->card;
-+ if (!mmc_card_sd(card) && mmc_card_blockaddr(card)) {
-+ /*
-+ * The EXT_CSD sector count is in number of 512 byte
-+ * sectors.
-+ */
-+ host->sectors = card->ext_csd.sectors;
-+ } else {
-+ /*
-+ * The CSD capacity field is in units of read_blkbits.
-+ * set_capacity takes units of 512 bytes.
-+ */
-+ host->sectors = card->csd.capacity <<
-+ (card->csd.read_blkbits - 9);
-+ }
-+ }
-+
- if (!host->dma_desc) {
- /* Use PIO */
- int flags = SG_MITER_ATOMIC;
-@@ -989,7 +1011,7 @@ bool bcm2835_sdhost_send_command(struct
-
- if (cmd->data) {
- log_event("CMDD", cmd->data->blocks, cmd->data->blksz);
-- if (host->delay_after_stop) {
-+ if (host->delay_after_this_stop) {
- struct timeval now;
- int time_since_stop;
- do_gettimeofday(&now);
-@@ -998,12 +1020,32 @@ bool bcm2835_sdhost_send_command(struct
- /* Possibly less than one second */
- time_since_stop = time_since_stop * 1000000 +
- (now.tv_usec - host->stop_time.tv_usec);
-- if (time_since_stop < host->delay_after_stop)
-- udelay(host->delay_after_stop -
-+ if (time_since_stop <
-+ host->delay_after_this_stop)
-+ udelay(host->delay_after_this_stop -
- time_since_stop);
- }
- }
-
-+ host->delay_after_this_stop = host->delay_after_stop;
-+ if ((cmd->data->flags & MMC_DATA_READ) && !host->use_sbc) {
-+ /* See if read crosses one of the hazardous sectors */
-+ u32 first_blk, last_blk;
-+
-+ /* Intentionally include the following sector because
-+ without CMD23/SBC the read may run on. */
-+ first_blk = host->mrq->cmd->arg;
-+ last_blk = first_blk + cmd->data->blocks;
-+
-+ if (((last_blk >= (host->sectors - 64)) &&
-+ (first_blk <= (host->sectors - 64))) ||
-+ ((last_blk >= (host->sectors - 32)) &&
-+ (first_blk <= (host->sectors - 32)))) {
-+ host->delay_after_this_stop =
-+ max(250u, host->delay_after_stop);
-+ }
-+ }
-+
- if (cmd->data->flags & MMC_DATA_WRITE)
- sdcmd |= SDCMD_WRITE_CMD;
- if (cmd->data->flags & MMC_DATA_READ)
-@@ -1078,7 +1120,7 @@ static void bcm2835_sdhost_transfer_comp
- if (!host->use_busy)
- bcm2835_sdhost_finish_command(host, NULL);
-
-- if (host->delay_after_stop)
-+ if (host->delay_after_this_stop)
- do_gettimeofday(&host->stop_time);
- }
- } else {
diff --git a/target/linux/brcm2708/patches-4.4/0186-BCM270X_DT-Add-labels-to-spidev-nodes.patch b/target/linux/brcm2708/patches-4.4/0186-BCM270X_DT-Add-labels-to-spidev-nodes.patch
deleted file mode 100644
index 5dfe2a4..0000000
--- a/target/linux/brcm2708/patches-4.4/0186-BCM270X_DT-Add-labels-to-spidev-nodes.patch
+++ /dev/null
@@ -1,114 +0,0 @@
-From 14be8e80fe39af4b042511c8acc1fb15aeb1885d Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Tue, 15 Mar 2016 15:49:16 +0000
-Subject: [PATCH] BCM270X_DT: Add labels to spidev nodes
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/bcm2708-rpi-b-plus.dts | 4 ++--
- arch/arm/boot/dts/bcm2708-rpi-b.dts | 4 ++--
- arch/arm/boot/dts/bcm2708-rpi-cm.dts | 4 ++--
- arch/arm/boot/dts/bcm2709-rpi-2-b.dts | 4 ++--
- arch/arm/boot/dts/bcm2710-rpi-3-b.dts | 4 ++--
- 5 files changed, 10 insertions(+), 10 deletions(-)
-
---- a/arch/arm/boot/dts/bcm2708-rpi-b-plus.dts
-+++ b/arch/arm/boot/dts/bcm2708-rpi-b-plus.dts
-@@ -59,7 +59,7 @@
- pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
- cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
-
-- spidev at 0{
-+ spidev0: spidev at 0{
- compatible = "spidev";
- reg = <0>; /* CE0 */
- #address-cells = <1>;
-@@ -67,7 +67,7 @@
- spi-max-frequency = <500000>;
- };
-
-- spidev at 1{
-+ spidev1: spidev at 1{
- compatible = "spidev";
- reg = <1>; /* CE1 */
- #address-cells = <1>;
---- a/arch/arm/boot/dts/bcm2708-rpi-b.dts
-+++ b/arch/arm/boot/dts/bcm2708-rpi-b.dts
-@@ -59,7 +59,7 @@
- pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
- cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
-
-- spidev at 0{
-+ spidev0: spidev at 0{
- compatible = "spidev";
- reg = <0>; /* CE0 */
- #address-cells = <1>;
-@@ -67,7 +67,7 @@
- spi-max-frequency = <500000>;
- };
-
-- spidev at 1{
-+ spidev1: spidev at 1{
- compatible = "spidev";
- reg = <1>; /* CE1 */
- #address-cells = <1>;
---- a/arch/arm/boot/dts/bcm2708-rpi-cm.dts
-+++ b/arch/arm/boot/dts/bcm2708-rpi-cm.dts
-@@ -42,7 +42,7 @@
- pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
- cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
-
-- spidev at 0{
-+ spidev0: spidev at 0{
- compatible = "spidev";
- reg = <0>; /* CE0 */
- #address-cells = <1>;
-@@ -50,7 +50,7 @@
- spi-max-frequency = <500000>;
- };
-
-- spidev at 1{
-+ spidev1: spidev at 1{
- compatible = "spidev";
- reg = <1>; /* CE1 */
- #address-cells = <1>;
---- a/arch/arm/boot/dts/bcm2709-rpi-2-b.dts
-+++ b/arch/arm/boot/dts/bcm2709-rpi-2-b.dts
-@@ -59,7 +59,7 @@
- pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
- cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
-
-- spidev at 0{
-+ spidev0: spidev at 0{
- compatible = "spidev";
- reg = <0>; /* CE0 */
- #address-cells = <1>;
-@@ -67,7 +67,7 @@
- spi-max-frequency = <500000>;
- };
-
-- spidev at 1{
-+ spidev1: spidev at 1{
- compatible = "spidev";
- reg = <1>; /* CE1 */
- #address-cells = <1>;
---- a/arch/arm/boot/dts/bcm2710-rpi-3-b.dts
-+++ b/arch/arm/boot/dts/bcm2710-rpi-3-b.dts
-@@ -110,7 +110,7 @@
- pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
- cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
-
-- spidev at 0{
-+ spidev0: spidev at 0{
- compatible = "spidev";
- reg = <0>; /* CE0 */
- #address-cells = <1>;
-@@ -118,7 +118,7 @@
- spi-max-frequency = <500000>;
- };
-
-- spidev at 1{
-+ spidev1: spidev at 1{
- compatible = "spidev";
- reg = <1>; /* CE1 */
- #address-cells = <1>;
diff --git a/target/linux/brcm2708/patches-4.4/0187-BCM270X_DT-Use-spidev-labels-in-overlays.patch b/target/linux/brcm2708/patches-4.4/0187-BCM270X_DT-Use-spidev-labels-in-overlays.patch
deleted file mode 100644
index f2917af..0000000
--- a/target/linux/brcm2708/patches-4.4/0187-BCM270X_DT-Use-spidev-labels-in-overlays.patch
+++ /dev/null
@@ -1,628 +0,0 @@
-From 40f425862e85fcdfd8222ad6169b60f58d430cb9 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Tue, 15 Mar 2016 16:27:26 +0000
-Subject: [PATCH] BCM270X_DT: Use spidev labels in overlays
-
----
- arch/arm/boot/dts/overlays/ads7846-overlay.dts | 22 ++++++++++-------
- arch/arm/boot/dts/overlays/at86rf233-overlay.dts | 11 +++++----
- arch/arm/boot/dts/overlays/enc28j60-overlay.dts | 11 +++++----
- arch/arm/boot/dts/overlays/hy28a-overlay.dts | 22 ++++++++++-------
- arch/arm/boot/dts/overlays/hy28b-overlay.dts | 22 ++++++++++-------
- .../arm/boot/dts/overlays/mcp2515-can0-overlay.dts | 16 ++++++++-----
- .../arm/boot/dts/overlays/mcp2515-can1-overlay.dts | 16 ++++++++-----
- arch/arm/boot/dts/overlays/mz61581-overlay.dts | 22 ++++++++++-------
- arch/arm/boot/dts/overlays/piscreen-overlay.dts | 22 ++++++++++-------
- arch/arm/boot/dts/overlays/piscreen2r-overlay.dts | 22 ++++++++++-------
- .../dts/overlays/pitft28-capacitive-overlay.dts | 17 +++++++------
- .../dts/overlays/pitft28-resistive-overlay.dts | 24 ++++++++++++-------
- arch/arm/boot/dts/overlays/rpi-display-overlay.dts | 22 ++++++++++-------
- arch/arm/boot/dts/overlays/tinylcd35-overlay.dts | 28 +++++++++++++---------
- 14 files changed, 174 insertions(+), 103 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/ads7846-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/ads7846-overlay.dts
-@@ -13,18 +13,24 @@
- target = <&spi0>;
- __overlay__ {
- status = "okay";
-+ };
-+ };
-
-- spidev at 0{
-- status = "disabled";
-- };
-+ fragment at 1 {
-+ target = <&spidev0>;
-+ __overlay__ {
-+ status = "disabled";
-+ };
-+ };
-
-- spidev at 1{
-- status = "disabled";
-- };
-+ fragment at 2 {
-+ target = <&spidev1>;
-+ __overlay__ {
-+ status = "disabled";
- };
- };
-
-- fragment at 1 {
-+ fragment at 3 {
- target = <&gpio>;
- __overlay__ {
- ads7846_pins: ads7846_pins {
-@@ -35,7 +41,7 @@
- };
- };
-
-- fragment at 2 {
-+ fragment at 4 {
- target = <&spi0>;
- __overlay__ {
- /* needed to avoid dtc warning */
---- a/arch/arm/boot/dts/overlays/at86rf233-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/at86rf233-overlay.dts
-@@ -14,10 +14,6 @@
-
- status = "okay";
-
-- spidev at 0{
-- status = "disabled";
-- };
--
- lowpan0: at86rf233 at 0 {
- compatible = "atmel,at86rf233";
- reg = <0>;
-@@ -32,6 +28,13 @@
- };
-
- fragment at 1 {
-+ target = <&spidev0>;
-+ __overlay__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ fragment at 2 {
- target = <&gpio>;
- __overlay__ {
- lowpan0_pins: lowpan0_pins {
---- a/arch/arm/boot/dts/overlays/enc28j60-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/enc28j60-overlay.dts
-@@ -14,10 +14,6 @@
-
- status = "okay";
-
-- spidev at 0{
-- status = "disabled";
-- };
--
- eth1: enc28j60 at 0{
- compatible = "microchip,enc28j60";
- reg = <0>; /* CE0 */
-@@ -32,6 +28,13 @@
- };
-
- fragment at 1 {
-+ target = <&spidev0>;
-+ __overlay__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ fragment at 2 {
- target = <&gpio>;
- __overlay__ {
- eth1_pins: eth1_pins {
---- a/arch/arm/boot/dts/overlays/hy28a-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/hy28a-overlay.dts
-@@ -13,18 +13,24 @@
- target = <&spi0>;
- __overlay__ {
- status = "okay";
-+ };
-+ };
-
-- spidev at 0{
-- status = "disabled";
-- };
-+ fragment at 1 {
-+ target = <&spidev0>;
-+ __overlay__ {
-+ status = "disabled";
-+ };
-+ };
-
-- spidev at 1{
-- status = "disabled";
-- };
-+ fragment at 2 {
-+ target = <&spidev1>;
-+ __overlay__ {
-+ status = "disabled";
- };
- };
-
-- fragment at 1 {
-+ fragment at 3 {
- target = <&gpio>;
- __overlay__ {
- hy28a_pins: hy28a_pins {
-@@ -34,7 +40,7 @@
- };
- };
-
-- fragment at 2 {
-+ fragment at 4 {
- target = <&spi0>;
- __overlay__ {
- /* needed to avoid dtc warning */
---- a/arch/arm/boot/dts/overlays/hy28b-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/hy28b-overlay.dts
-@@ -13,18 +13,24 @@
- target = <&spi0>;
- __overlay__ {
- status = "okay";
-+ };
-+ };
-
-- spidev at 0{
-- status = "disabled";
-- };
-+ fragment at 1 {
-+ target = <&spidev0>;
-+ __overlay__ {
-+ status = "disabled";
-+ };
-+ };
-
-- spidev at 1{
-- status = "disabled";
-- };
-+ fragment at 2 {
-+ target = <&spidev1>;
-+ __overlay__ {
-+ status = "disabled";
- };
- };
-
-- fragment at 1 {
-+ fragment at 3 {
- target = <&gpio>;
- __overlay__ {
- hy28b_pins: hy28b_pins {
-@@ -34,7 +40,7 @@
- };
- };
-
-- fragment at 2 {
-+ fragment at 4 {
- target = <&spi0>;
- __overlay__ {
- /* needed to avoid dtc warning */
---- a/arch/arm/boot/dts/overlays/mcp2515-can0-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/mcp2515-can0-overlay.dts
-@@ -12,14 +12,18 @@
- target = <&spi0>;
- __overlay__ {
- status = "okay";
-- spidev at 0{
-- status = "disabled";
-- };
- };
- };
-
-- /* the interrupt pin of the can-controller */
- fragment at 1 {
-+ target = <&spidev0>;
-+ __overlay__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ /* the interrupt pin of the can-controller */
-+ fragment at 2 {
- target = <&gpio>;
- __overlay__ {
- can0_pins: can0_pins {
-@@ -30,7 +34,7 @@
- };
-
- /* the clock/oscillator of the can-controller */
-- fragment at 2 {
-+ fragment at 3 {
- target-path = "/clocks";
- __overlay__ {
- /* external oscillator of mcp2515 on SPI0.0 */
-@@ -43,7 +47,7 @@
- };
-
- /* the spi config of the can-controller itself binding everything together */
-- fragment at 3 {
-+ fragment at 4 {
- target = <&spi0>;
- __overlay__ {
- /* needed to avoid dtc warning */
---- a/arch/arm/boot/dts/overlays/mcp2515-can1-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/mcp2515-can1-overlay.dts
-@@ -12,14 +12,18 @@
- target = <&spi0>;
- __overlay__ {
- status = "okay";
-- spidev at 1{
-- status = "disabled";
-- };
- };
- };
-
-- /* the interrupt pin of the can-controller */
- fragment at 1 {
-+ target = <&spidev1>;
-+ __overlay__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ /* the interrupt pin of the can-controller */
-+ fragment at 2 {
- target = <&gpio>;
- __overlay__ {
- can1_pins: can1_pins {
-@@ -30,7 +34,7 @@
- };
-
- /* the clock/oscillator of the can-controller */
-- fragment at 2 {
-+ fragment at 3 {
- target-path = "/clocks";
- __overlay__ {
- /* external oscillator of mcp2515 on spi0.1 */
-@@ -43,7 +47,7 @@
- };
-
- /* the spi config of the can-controller itself binding everything together */
-- fragment at 3 {
-+ fragment at 4 {
- target = <&spi0>;
- __overlay__ {
- /* needed to avoid dtc warning */
---- a/arch/arm/boot/dts/overlays/mz61581-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/mz61581-overlay.dts
-@@ -13,18 +13,24 @@
- target = <&spi0>;
- __overlay__ {
- status = "okay";
-+ };
-+ };
-
-- spidev at 0{
-- status = "disabled";
-- };
-+ fragment at 1 {
-+ target = <&spidev0>;
-+ __overlay__ {
-+ status = "disabled";
-+ };
-+ };
-
-- spidev at 1{
-- status = "disabled";
-- };
-+ fragment at 2 {
-+ target = <&spidev1>;
-+ __overlay__ {
-+ status = "disabled";
- };
- };
-
-- fragment at 1 {
-+ fragment at 3 {
- target = <&gpio>;
- __overlay__ {
- mz61581_pins: mz61581_pins {
-@@ -34,7 +40,7 @@
- };
- };
-
-- fragment at 2 {
-+ fragment at 4 {
- target = <&spi0>;
- __overlay__ {
- /* needed to avoid dtc warning */
---- a/arch/arm/boot/dts/overlays/piscreen-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/piscreen-overlay.dts
-@@ -13,18 +13,24 @@
- target = <&spi0>;
- __overlay__ {
- status = "okay";
-+ };
-+ };
-
-- spidev at 0{
-- status = "disabled";
-- };
-+ fragment at 1 {
-+ target = <&spidev0>;
-+ __overlay__ {
-+ status = "disabled";
-+ };
-+ };
-
-- spidev at 1{
-- status = "disabled";
-- };
-+ fragment at 2 {
-+ target = <&spidev1>;
-+ __overlay__ {
-+ status = "disabled";
- };
- };
-
-- fragment at 1 {
-+ fragment at 3 {
- target = <&gpio>;
- __overlay__ {
- piscreen_pins: piscreen_pins {
-@@ -34,7 +40,7 @@
- };
- };
-
-- fragment at 2 {
-+ fragment at 4 {
- target = <&spi0>;
- __overlay__ {
- /* needed to avoid dtc warning */
---- a/arch/arm/boot/dts/overlays/piscreen2r-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/piscreen2r-overlay.dts
-@@ -13,18 +13,24 @@
- target = <&spi0>;
- __overlay__ {
- status = "okay";
-+ };
-+ };
-
-- spidev at 0{
-- status = "disabled";
-- };
-+ fragment at 1 {
-+ target = <&spidev0>;
-+ __overlay__ {
-+ status = "disabled";
-+ };
-+ };
-
-- spidev at 1{
-- status = "disabled";
-- };
-+ fragment at 2 {
-+ target = <&spidev1>;
-+ __overlay__ {
-+ status = "disabled";
- };
- };
-
-- fragment at 1 {
-+ fragment at 3 {
- target = <&gpio>;
- __overlay__ {
- piscreen2_pins: piscreen2_pins {
-@@ -34,7 +40,7 @@
- };
- };
-
-- fragment at 2 {
-+ fragment at 4 {
- target = <&spi0>;
- __overlay__ {
- /* needed to avoid dtc warning */
---- a/arch/arm/boot/dts/overlays/pitft28-capacitive-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/pitft28-capacitive-overlay.dts
-@@ -13,14 +13,17 @@
- target = <&spi0>;
- __overlay__ {
- status = "okay";
--
-- spidev at 0{
-- status = "disabled";
-- };
- };
- };
-
-- fragment at 1 {
-+ fragment at 1 {
-+ target = <&spidev0>;
-+ __overlay__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ fragment at 2 {
- target = <&gpio>;
- __overlay__ {
- pitft_pins: pitft_pins {
-@@ -31,7 +34,7 @@
- };
- };
-
-- fragment at 2 {
-+ fragment at 3 {
- target = <&spi0>;
- __overlay__ {
- /* needed to avoid dtc warning */
-@@ -55,7 +58,7 @@
- };
- };
-
-- fragment at 3 {
-+ fragment at 4 {
- target = <&i2c1>;
- __overlay__ {
- /* needed to avoid dtc warning */
---- a/arch/arm/boot/dts/overlays/pitft28-resistive-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/pitft28-resistive-overlay.dts
-@@ -13,18 +13,24 @@
- target = <&spi0>;
- __overlay__ {
- status = "okay";
-+ };
-+ };
-
-- spidev at 0{
-- status = "disabled";
-- };
-+ fragment at 1 {
-+ target = <&spidev0>;
-+ __overlay__ {
-+ status = "disabled";
-+ };
-+ };
-
-- spidev at 1{
-- status = "disabled";
-- };
-+ fragment at 2 {
-+ target = <&spidev1>;
-+ __overlay__ {
-+ status = "disabled";
- };
- };
-
-- fragment at 1 {
-+ fragment at 3 {
- target = <&gpio>;
- __overlay__ {
- pitft_pins: pitft_pins {
-@@ -35,7 +41,7 @@
- };
- };
-
-- fragment at 2 {
-+ fragment at 4 {
- target = <&spi0>;
- __overlay__ {
- /* needed to avoid dtc warning */
-@@ -95,7 +101,7 @@
- };
- };
-
-- fragment at 3 {
-+ fragment at 5 {
- target-path = "/soc";
- __overlay__ {
- backlight {
---- a/arch/arm/boot/dts/overlays/rpi-display-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/rpi-display-overlay.dts
-@@ -13,18 +13,24 @@
- target = <&spi0>;
- __overlay__ {
- status = "okay";
-+ };
-+ };
-
-- spidev at 0{
-- status = "disabled";
-- };
-+ fragment at 1 {
-+ target = <&spidev0>;
-+ __overlay__ {
-+ status = "disabled";
-+ };
-+ };
-
-- spidev at 1{
-- status = "disabled";
-- };
-+ fragment at 2 {
-+ target = <&spidev1>;
-+ __overlay__ {
-+ status = "disabled";
- };
- };
-
-- fragment at 1 {
-+ fragment at 3 {
- target = <&gpio>;
- __overlay__ {
- rpi_display_pins: rpi_display_pins {
-@@ -35,7 +41,7 @@
- };
- };
-
-- fragment at 2 {
-+ fragment at 4 {
- target = <&spi0>;
- __overlay__ {
- /* needed to avoid dtc warning */
---- a/arch/arm/boot/dts/overlays/tinylcd35-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/tinylcd35-overlay.dts
-@@ -30,18 +30,24 @@
- target = <&spi0>;
- __overlay__ {
- status = "okay";
-+ };
-+ };
-
-- spidev at 0{
-- status = "disabled";
-- };
-+ fragment at 1 {
-+ target = <&spidev0>;
-+ __overlay__ {
-+ status = "disabled";
-+ };
-+ };
-
-- spidev at 1{
-- status = "disabled";
-- };
-+ fragment at 2 {
-+ target = <&spidev1>;
-+ __overlay__ {
-+ status = "disabled";
- };
- };
-
-- fragment at 1 {
-+ fragment at 3 {
- target = <&gpio>;
- __overlay__ {
- tinylcd35_pins: tinylcd35_pins {
-@@ -60,7 +66,7 @@
- };
- };
-
-- fragment at 2 {
-+ fragment at 4 {
- target = <&spi0>;
- __overlay__ {
- /* needed to avoid dtc warning */
-@@ -124,7 +130,7 @@
-
- /* RTC */
-
-- fragment at 3 {
-+ fragment at 5 {
- target = <&i2c1>;
- __overlay__ {
- #address-cells = <1>;
-@@ -138,7 +144,7 @@
- };
- };
-
-- fragment at 4 {
-+ fragment at 6 {
- target = <&i2c1>;
- __overlay__ {
- #address-cells = <1>;
-@@ -156,7 +162,7 @@
- * Values for input event code is found under the
- * 'Keys and buttons' heading in include/uapi/linux/input.h
- */
-- fragment at 5 {
-+ fragment at 7 {
- target-path = "/soc";
- __overlay__ {
- keypad: keypad {
diff --git a/target/linux/brcm2708/patches-4.4/0188-BCM270X_DT-Build-and-document-the-wittypi-overlay.patch b/target/linux/brcm2708/patches-4.4/0188-BCM270X_DT-Build-and-document-the-wittypi-overlay.patch
deleted file mode 100644
index 80355e3..0000000
--- a/target/linux/brcm2708/patches-4.4/0188-BCM270X_DT-Build-and-document-the-wittypi-overlay.patch
+++ /dev/null
@@ -1,50 +0,0 @@
-From b4d870dddb6127a762d67530b80658ba8adccbfb Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Tue, 15 Mar 2016 16:41:37 +0000
-Subject: [PATCH] BCM270X_DT: Build and document the wittypi overlay
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 8 ++++++++
- arch/arm/boot/dts/overlays/wittypi-overlay.dts | 2 +-
- 3 files changed, 10 insertions(+), 1 deletion(-)
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -74,6 +74,7 @@ dtbo-$(RPI_DT_OVERLAYS) += vc4-kms-v3d.d
- dtbo-$(RPI_DT_OVERLAYS) += vga666.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += w1-gpio.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += w1-gpio-pullup.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += wittypi.dtbo
-
- targets += dtbs dtbs_install
- targets += $(dtbo-y)
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -920,6 +920,14 @@ Params: gpiopin GPIO for
- extpullup GPIO for external pullup (default "5")
-
-
-+Name: wittypi
-+Info: Configures the wittypi RTC module.
-+Load: dtoverlay=wittypi,<param>=<val>
-+Params: led_gpio GPIO for LED (default "17")
-+ led_trigger Choose which activity the LED tracks (default
-+ "default-on")
-+
-+
- Troubleshooting
- ===============
-
---- a/arch/arm/boot/dts/overlays/wittypi-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/wittypi-overlay.dts
-@@ -37,7 +37,7 @@
- };
-
- __overrides__ {
-- led_gpio = <&wittypi_led>,"gpios:4";
-+ led_gpio = <&wittypi_led>,"gpios:4";
- led_trigger = <&wittypi_led>,"linux,default-trigger";
- };
-
diff --git a/target/linux/brcm2708/patches-4.4/0189-scripts-dtc-Fix-UMR-causing-corrupt-dtbo-overlay-fil.patch b/target/linux/brcm2708/patches-4.4/0189-scripts-dtc-Fix-UMR-causing-corrupt-dtbo-overlay-fil.patch
deleted file mode 100644
index cc72380..0000000
--- a/target/linux/brcm2708/patches-4.4/0189-scripts-dtc-Fix-UMR-causing-corrupt-dtbo-overlay-fil.patch
+++ /dev/null
@@ -1,26 +0,0 @@
-From e564fbc9655417becb0477e19da99444e6c0c417 Mon Sep 17 00:00:00 2001
-From: Matthias Reichl <hias at horus.com>
-Date: Tue, 15 Mar 2016 21:13:39 +0100
-Subject: [PATCH] scripts/dtc: Fix UMR causing corrupt dtbo overlay files
-
-struct fixup_entry is allocated from the heap but it's member
-local_fixup_generated was never initialized. This lead to
-corrupted dtbo files.
-
-Fix this by initializing local_fixup_generated to false.
-
-Signed-off-by: Matthias Reichl <hias at horus.com>
----
- scripts/dtc/checks.c | 1 +
- 1 file changed, 1 insertion(+)
-
---- a/scripts/dtc/checks.c
-+++ b/scripts/dtc/checks.c
-@@ -523,6 +523,7 @@ static void fixup_phandle_references(str
- fe->prop = prop;
- fe->offset = m->offset;
- fe->next = NULL;
-+ fe->local_fixup_generated = false;
-
- /* append it to the local fixups */
- fep = &dt->local_fixups;
diff --git a/target/linux/brcm2708/patches-4.4/0190-BCM270X_DT-Add-dtparam-for-uart1.patch b/target/linux/brcm2708/patches-4.4/0190-BCM270X_DT-Add-dtparam-for-uart1.patch
deleted file mode 100644
index a047023..0000000
--- a/target/linux/brcm2708/patches-4.4/0190-BCM270X_DT-Add-dtparam-for-uart1.patch
+++ /dev/null
@@ -1,77 +0,0 @@
-From c3aa6acf36175b310627605fe1dc5a3e87bc903a Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Wed, 16 Mar 2016 08:35:06 +0000
-Subject: [PATCH] BCM270X_DT: Add dtparam for uart1
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/bcm2708-rpi-b-plus.dts | 1 +
- arch/arm/boot/dts/bcm2708-rpi-b.dts | 1 +
- arch/arm/boot/dts/bcm2708-rpi-cm.dts | 1 +
- arch/arm/boot/dts/bcm2709-rpi-2-b.dts | 1 +
- arch/arm/boot/dts/bcm2710-rpi-3-b.dts | 1 +
- arch/arm/boot/dts/overlays/README | 3 +++
- 6 files changed, 8 insertions(+)
-
---- a/arch/arm/boot/dts/bcm2708-rpi-b-plus.dts
-+++ b/arch/arm/boot/dts/bcm2708-rpi-b-plus.dts
-@@ -120,6 +120,7 @@
- __overrides__ {
- uart0 = <&uart0>,"status";
- uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
-+ uart1 = <&uart1>,"status";
- i2s = <&i2s>,"status";
- spi = <&spi0>,"status";
- i2c0 = <&i2c0>,"status";
---- a/arch/arm/boot/dts/bcm2708-rpi-b.dts
-+++ b/arch/arm/boot/dts/bcm2708-rpi-b.dts
-@@ -114,6 +114,7 @@
- __overrides__ {
- uart0 = <&uart0>,"status";
- uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
-+ uart1 = <&uart1>,"status";
- i2s = <&i2s>,"status";
- spi = <&spi0>,"status";
- i2c0 = <&i2c0>,"status";
---- a/arch/arm/boot/dts/bcm2708-rpi-cm.dts
-+++ b/arch/arm/boot/dts/bcm2708-rpi-cm.dts
-@@ -89,6 +89,7 @@
- __overrides__ {
- uart0 = <&uart0>,"status";
- uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
-+ uart1 = <&uart1>,"status";
- i2s = <&i2s>,"status";
- spi = <&spi0>,"status";
- i2c0 = <&i2c0>,"status";
---- a/arch/arm/boot/dts/bcm2709-rpi-2-b.dts
-+++ b/arch/arm/boot/dts/bcm2709-rpi-2-b.dts
-@@ -120,6 +120,7 @@
- __overrides__ {
- uart0 = <&uart0>,"status";
- uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
-+ uart1 = <&uart1>,"status";
- i2s = <&i2s>,"status";
- spi = <&spi0>,"status";
- i2c0 = <&i2c0>,"status";
---- a/arch/arm/boot/dts/bcm2710-rpi-3-b.dts
-+++ b/arch/arm/boot/dts/bcm2710-rpi-3-b.dts
-@@ -171,6 +171,7 @@
- __overrides__ {
- uart0 = <&uart0>,"status";
- uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
-+ uart1 = <&uart1>,"status";
- i2s = <&i2s>,"status";
- spi = <&spi0>,"status";
- i2c0 = <&i2c0>,"status";
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -124,6 +124,9 @@ Params:
-
- uart0 Set to "off" to disable uart0 (default "on")
-
-+ uart1 Set to "on" or "off" to enable or disable uart1
-+ (default varies)
-+
- watchdog Set to "on" to enable the hardware watchdog
- (default "off")
-
diff --git a/target/linux/brcm2708/patches-4.4/0191-dwc-overlay-Use-label-so-overrides-can-apply.patch b/target/linux/brcm2708/patches-4.4/0191-dwc-overlay-Use-label-so-overrides-can-apply.patch
deleted file mode 100644
index 43e42d2..0000000
--- a/target/linux/brcm2708/patches-4.4/0191-dwc-overlay-Use-label-so-overrides-can-apply.patch
+++ /dev/null
@@ -1,34 +0,0 @@
-From afac265e770fe6b731d4483c5496401bbdaded4a Mon Sep 17 00:00:00 2001
-From: Przemek Rudy <prudy1 at o2.pl>
-Date: Fri, 11 Mar 2016 22:41:26 +0100
-Subject: [PATCH] dwc-overlay: Use label so overrides can apply.
-
----
- arch/arm/boot/dts/overlays/dwc2-overlay.dts | 10 +++++-----
- 1 file changed, 5 insertions(+), 5 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/dwc2-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/dwc2-overlay.dts
-@@ -8,7 +8,7 @@
- target = <&usb>;
- #address-cells = <1>;
- #size-cells = <1>;
-- __overlay__ {
-+ dwc2_usb: __overlay__ {
- compatible = "brcm,bcm2835-usb";
- reg = <0x7e980000 0x10000>;
- interrupts = <1 9>;
-@@ -21,9 +21,9 @@
- };
-
- __overrides__ {
-- dr_mode = <&usb>, "dr_mode";
-- g-np-tx-fifo-size = <&usb>,"g-np-tx-fifo-size:0";
-- g-rx-fifo-size = <&usb>,"g-rx-fifo-size:0";
-- g-tx-fifo-size = <&usb>,"g-tx-fifo-size:0";
-+ dr_mode = <&dwc2_usb>, "dr_mode";
-+ g-np-tx-fifo-size = <&dwc2_usb>,"g-np-tx-fifo-size:0";
-+ g-rx-fifo-size = <&dwc2_usb>,"g-rx-fifo-size:0";
-+ g-tx-fifo-size = <&dwc2_usb>,"g-tx-fifo-size:0";
- };
- };
diff --git a/target/linux/brcm2708/patches-4.4/0192-drm-vc4-Add-a-debugfs-node-for-tracking-execution-st.patch b/target/linux/brcm2708/patches-4.4/0192-drm-vc4-Add-a-debugfs-node-for-tracking-execution-st.patch
deleted file mode 100644
index b7006fe..0000000
--- a/target/linux/brcm2708/patches-4.4/0192-drm-vc4-Add-a-debugfs-node-for-tracking-execution-st.patch
+++ /dev/null
@@ -1,55 +0,0 @@
-From b84a32eae1e9dd52ee62714616a4755aac401670 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 22 Jan 2016 13:06:39 -0800
-Subject: [PATCH] drm/vc4: Add a debugfs node for tracking execution state.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_debugfs.c | 1 +
- drivers/gpu/drm/vc4/vc4_drv.h | 1 +
- drivers/gpu/drm/vc4/vc4_gem.c | 14 ++++++++++++++
- 3 files changed, 16 insertions(+)
-
---- a/drivers/gpu/drm/vc4/vc4_debugfs.c
-+++ b/drivers/gpu/drm/vc4/vc4_debugfs.c
-@@ -17,6 +17,7 @@
-
- static const struct drm_info_list vc4_debugfs_list[] = {
- {"bo_stats", vc4_bo_stats_debugfs, 0},
-+ {"gem_exec", vc4_gem_exec_debugfs, 0},
- {"hdmi_regs", vc4_hdmi_debugfs_regs, 0},
- {"hvs_regs", vc4_hvs_debugfs_regs, 0},
- {"crtc0_regs", vc4_crtc_debugfs_regs, 0, (void *)(uintptr_t)0},
---- a/drivers/gpu/drm/vc4/vc4_drv.h
-+++ b/drivers/gpu/drm/vc4/vc4_drv.h
-@@ -403,6 +403,7 @@ void vc4_job_handle_completed(struct vc4
- int vc4_queue_seqno_cb(struct drm_device *dev,
- struct vc4_seqno_cb *cb, uint64_t seqno,
- void (*func)(struct vc4_seqno_cb *cb));
-+int vc4_gem_exec_debugfs(struct seq_file *m, void *arg);
-
- /* vc4_hdmi.c */
- extern struct platform_driver vc4_hdmi_driver;
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -31,6 +31,20 @@
- #include "vc4_regs.h"
- #include "vc4_trace.h"
-
-+#ifdef CONFIG_DEBUG_FS
-+int vc4_gem_exec_debugfs(struct seq_file *m, void *unused)
-+{
-+ struct drm_info_node *node = (struct drm_info_node *)m->private;
-+ struct drm_device *dev = node->minor->dev;
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+
-+ seq_printf(m, "Emitted seqno: 0x%016llx\n", vc4->emit_seqno);
-+ seq_printf(m, "Finished seqno: 0x%016llx\n", vc4->finished_seqno);
-+
-+ return 0;
-+}
-+#endif /* CONFIG_DEBUG_FS */
-+
- static void
- vc4_queue_hangcheck(struct drm_device *dev)
- {
diff --git a/target/linux/brcm2708/patches-4.4/0193-drm-vc4-Include-vc4_drm.h-in-uapi-in-downstream-buil.patch b/target/linux/brcm2708/patches-4.4/0193-drm-vc4-Include-vc4_drm.h-in-uapi-in-downstream-buil.patch
deleted file mode 100644
index 91b9f88..0000000
--- a/target/linux/brcm2708/patches-4.4/0193-drm-vc4-Include-vc4_drm.h-in-uapi-in-downstream-buil.patch
+++ /dev/null
@@ -1,20 +0,0 @@
-From 02502e6f84f16c25bad064d1aaa0beddff841d8a Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 25 Jan 2016 13:03:33 -0800
-Subject: [PATCH] drm/vc4: Include vc4_drm.h in uapi in downstream build.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- include/uapi/drm/Kbuild | 1 +
- 1 file changed, 1 insertion(+)
-
---- a/include/uapi/drm/Kbuild
-+++ b/include/uapi/drm/Kbuild
-@@ -14,6 +14,7 @@ header-y += radeon_drm.h
- header-y += savage_drm.h
- header-y += sis_drm.h
- header-y += tegra_drm.h
-+header-y += vc4_drm.h
- header-y += via_drm.h
- header-y += vmwgfx_drm.h
- header-y += msm_drm.h
diff --git a/target/linux/brcm2708/patches-4.4/0194-drm-vc4-Validate-that-WAIT_BO-padding-is-cleared.patch b/target/linux/brcm2708/patches-4.4/0194-drm-vc4-Validate-that-WAIT_BO-padding-is-cleared.patch
deleted file mode 100644
index 6c9eb5e..0000000
--- a/target/linux/brcm2708/patches-4.4/0194-drm-vc4-Validate-that-WAIT_BO-padding-is-cleared.patch
+++ /dev/null
@@ -1,25 +0,0 @@
-From 635c15dedc5c00b2a3a65f4c8fe15b9003ab2159 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 25 Jan 2016 13:05:00 -0800
-Subject: [PATCH] drm/vc4: Validate that WAIT_BO padding is cleared.
-
-This is ABI future-proofing if we ever want to extend the pad to mean
-something.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_gem.c | 3 +++
- 1 file changed, 3 insertions(+)
-
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -761,6 +761,9 @@ vc4_wait_bo_ioctl(struct drm_device *dev
- struct drm_gem_object *gem_obj;
- struct vc4_bo *bo;
-
-+ if (args->pad != 0)
-+ return -EINVAL;
-+
- gem_obj = drm_gem_object_lookup(dev, file_priv, args->handle);
- if (!gem_obj) {
- DRM_ERROR("Failed to look up GEM BO %d\n", args->handle);
diff --git a/target/linux/brcm2708/patches-4.4/0195-drm-vc4-Fix-the-clear-color-for-the-first-tile-rende.patch b/target/linux/brcm2708/patches-4.4/0195-drm-vc4-Fix-the-clear-color-for-the-first-tile-rende.patch
deleted file mode 100644
index 7cb9bcf..0000000
--- a/target/linux/brcm2708/patches-4.4/0195-drm-vc4-Fix-the-clear-color-for-the-first-tile-rende.patch
+++ /dev/null
@@ -1,48 +0,0 @@
-From 3804cf13fbe66de0ffac009021b7e18e667f44a0 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 25 Jan 2016 13:52:41 -0800
-Subject: [PATCH] drm/vc4: Fix the clear color for the first tile rendered.
-
-Apparently in hardware (as opposed to simulation), the clear colors
-need to be uploaded before the render config, otherwise they won't
-take effect. Fixes igt's vc4_wait_bo/used-bo-* subtests.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_render_cl.c | 18 +++++++++---------
- 1 file changed, 9 insertions(+), 9 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_render_cl.c
-+++ b/drivers/gpu/drm/vc4/vc4_render_cl.c
-@@ -321,15 +321,6 @@ static int vc4_create_rcl_bo(struct drm_
- list_add_tail(&to_vc4_bo(&setup->rcl->base)->unref_head,
- &exec->unref_list);
-
-- rcl_u8(setup, VC4_PACKET_TILE_RENDERING_MODE_CONFIG);
-- rcl_u32(setup,
-- (setup->color_write ? (setup->color_write->paddr +
-- args->color_write.offset) :
-- 0));
-- rcl_u16(setup, args->width);
-- rcl_u16(setup, args->height);
-- rcl_u16(setup, args->color_write.bits);
--
- /* The tile buffer gets cleared when the previous tile is stored. If
- * the clear values changed between frames, then the tile buffer has
- * stale clear values in it, so we have to do a store in None mode (no
-@@ -349,6 +340,15 @@ static int vc4_create_rcl_bo(struct drm_
- rcl_u32(setup, 0); /* no address, since we're in None mode */
- }
-
-+ rcl_u8(setup, VC4_PACKET_TILE_RENDERING_MODE_CONFIG);
-+ rcl_u32(setup,
-+ (setup->color_write ? (setup->color_write->paddr +
-+ args->color_write.offset) :
-+ 0));
-+ rcl_u16(setup, args->width);
-+ rcl_u16(setup, args->height);
-+ rcl_u16(setup, args->color_write.bits);
-+
- for (y = min_y_tile; y <= max_y_tile; y++) {
- for (x = min_x_tile; x <= max_x_tile; x++) {
- bool first = (x == min_x_tile && y == min_y_tile);
diff --git a/target/linux/brcm2708/patches-4.4/0196-drm-vc4-Return-an-ERR_PTR-from-BO-creation-instead-o.patch b/target/linux/brcm2708/patches-4.4/0196-drm-vc4-Return-an-ERR_PTR-from-BO-creation-instead-o.patch
deleted file mode 100644
index da07a3e..0000000
--- a/target/linux/brcm2708/patches-4.4/0196-drm-vc4-Return-an-ERR_PTR-from-BO-creation-instead-o.patch
+++ /dev/null
@@ -1,136 +0,0 @@
-From be92a6b3e5378018b3c958631a706ce5e5534734 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 25 Jan 2016 14:13:12 -0800
-Subject: [PATCH] drm/vc4: Return an ERR_PTR from BO creation instead of NULL.
-
-Fixes igt vc4_create_bo/create-bo-0 by returning -EINVAL from the
-ioctl instead of -ENOMEM.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_bo.c | 23 +++++++++++++----------
- drivers/gpu/drm/vc4/vc4_gem.c | 4 ++--
- drivers/gpu/drm/vc4/vc4_irq.c | 2 +-
- drivers/gpu/drm/vc4/vc4_render_cl.c | 4 ++--
- drivers/gpu/drm/vc4/vc4_validate.c | 4 ++--
- 5 files changed, 20 insertions(+), 17 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_bo.c
-+++ b/drivers/gpu/drm/vc4/vc4_bo.c
-@@ -213,10 +213,10 @@ struct vc4_bo *vc4_bo_create(struct drm_
- size_t size = roundup(unaligned_size, PAGE_SIZE);
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct drm_gem_cma_object *cma_obj;
-- int pass;
-+ int pass, ret;
-
- if (size == 0)
-- return NULL;
-+ return ERR_PTR(-EINVAL);
-
- /* First, try to get a vc4_bo from the kernel BO cache. */
- if (from_cache) {
-@@ -247,14 +247,17 @@ struct vc4_bo *vc4_bo_create(struct drm_
- * unreferenced BOs to the cache, and then
- * free the cache.
- */
-- vc4_wait_for_seqno(dev, vc4->emit_seqno, ~0ull, true);
-+ ret = vc4_wait_for_seqno(dev, vc4->emit_seqno, ~0ull,
-+ true);
-+ if (ret)
-+ return ERR_PTR(ret);
- vc4_job_handle_completed(vc4);
- vc4_bo_cache_purge(dev);
- break;
- case 3:
- DRM_ERROR("Failed to allocate from CMA:\n");
- vc4_bo_stats_dump(vc4);
-- return NULL;
-+ return ERR_PTR(-ENOMEM);
- }
- }
-
-@@ -276,8 +279,8 @@ int vc4_dumb_create(struct drm_file *fil
- args->size = args->pitch * args->height;
-
- bo = vc4_bo_create(dev, args->size, false);
-- if (!bo)
-- return -ENOMEM;
-+ if (IS_ERR(bo))
-+ return PTR_ERR(bo);
-
- ret = drm_gem_handle_create(file_priv, &bo->base.base, &args->handle);
- drm_gem_object_unreference_unlocked(&bo->base.base);
-@@ -460,8 +463,8 @@ int vc4_create_bo_ioctl(struct drm_devic
- * get zeroed, and that might leak data between users.
- */
- bo = vc4_bo_create(dev, args->size, false);
-- if (!bo)
-- return -ENOMEM;
-+ if (IS_ERR(bo))
-+ return PTR_ERR(bo);
-
- ret = drm_gem_handle_create(file_priv, &bo->base.base, &args->handle);
- drm_gem_object_unreference_unlocked(&bo->base.base);
-@@ -513,8 +516,8 @@ vc4_create_shader_bo_ioctl(struct drm_de
- }
-
- bo = vc4_bo_create(dev, args->size, true);
-- if (!bo)
-- return -ENOMEM;
-+ if (IS_ERR(bo))
-+ return PTR_ERR(bo);
-
- ret = copy_from_user(bo->base.vaddr,
- (void __user *)(uintptr_t)args->data,
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -593,9 +593,9 @@ vc4_get_bcl(struct drm_device *dev, stru
- }
-
- bo = vc4_bo_create(dev, exec_size, true);
-- if (!bo) {
-+ if (IS_ERR(bo)) {
- DRM_ERROR("Couldn't allocate BO for binning\n");
-- ret = PTR_ERR(exec->exec_bo);
-+ ret = PTR_ERR(bo);
- goto fail;
- }
- exec->exec_bo = &bo->base;
---- a/drivers/gpu/drm/vc4/vc4_irq.c
-+++ b/drivers/gpu/drm/vc4/vc4_irq.c
-@@ -57,7 +57,7 @@ vc4_overflow_mem_work(struct work_struct
- struct vc4_bo *bo;
-
- bo = vc4_bo_create(dev, 256 * 1024, true);
-- if (!bo) {
-+ if (IS_ERR(bo)) {
- DRM_ERROR("Couldn't allocate binner overflow mem\n");
- return;
- }
---- a/drivers/gpu/drm/vc4/vc4_render_cl.c
-+++ b/drivers/gpu/drm/vc4/vc4_render_cl.c
-@@ -316,8 +316,8 @@ static int vc4_create_rcl_bo(struct drm_
- size += xtiles * ytiles * loop_body_size;
-
- setup->rcl = &vc4_bo_create(dev, size, true)->base;
-- if (!setup->rcl)
-- return -ENOMEM;
-+ if (IS_ERR(setup->rcl))
-+ return PTR_ERR(setup->rcl);
- list_add_tail(&to_vc4_bo(&setup->rcl->base)->unref_head,
- &exec->unref_list);
-
---- a/drivers/gpu/drm/vc4/vc4_validate.c
-+++ b/drivers/gpu/drm/vc4/vc4_validate.c
-@@ -401,8 +401,8 @@ validate_tile_binning_config(VALIDATE_AR
- tile_bo = vc4_bo_create(dev, exec->tile_alloc_offset + tile_alloc_size,
- true);
- exec->tile_bo = &tile_bo->base;
-- if (!exec->tile_bo)
-- return -ENOMEM;
-+ if (IS_ERR(exec->tile_bo))
-+ return PTR_ERR(exec->tile_bo);
- list_add_tail(&tile_bo->unref_head, &exec->unref_list);
-
- /* tile alloc address. */
diff --git a/target/linux/brcm2708/patches-4.4/0197-drm-vc4-Fix-ERESTARTSYS-error-return-from-BO-waits.patch b/target/linux/brcm2708/patches-4.4/0197-drm-vc4-Fix-ERESTARTSYS-error-return-from-BO-waits.patch
deleted file mode 100644
index 2fe5900..0000000
--- a/target/linux/brcm2708/patches-4.4/0197-drm-vc4-Fix-ERESTARTSYS-error-return-from-BO-waits.patch
+++ /dev/null
@@ -1,32 +0,0 @@
-From bbbf1b8b37cadf400d0ae7e198f3423c73b39842 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 25 Jan 2016 14:32:41 -0800
-Subject: [PATCH] drm/vc4: Fix -ERESTARTSYS error return from BO waits.
-
-This caused the wait ioctls to claim that waiting had completed when
-we actually got interrupted by a signal before it was done. Fixes
-broken rendering throttling that produced serious lag in X window
-dragging.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_gem.c | 6 ++----
- 1 file changed, 2 insertions(+), 4 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -352,12 +352,10 @@ vc4_wait_for_seqno(struct drm_device *de
- finish_wait(&vc4->job_wait_queue, &wait);
- trace_vc4_wait_for_seqno_end(dev, seqno);
-
-- if (ret && ret != -ERESTARTSYS) {
-+ if (ret && ret != -ERESTARTSYS)
- DRM_ERROR("timeout waiting for render thread idle\n");
-- return ret;
-- }
-
-- return 0;
-+ return ret;
- }
-
- static void
diff --git a/target/linux/brcm2708/patches-4.4/0198-drm-vc4-Drop-error-message-on-seqno-wait-timeouts.patch b/target/linux/brcm2708/patches-4.4/0198-drm-vc4-Drop-error-message-on-seqno-wait-timeouts.patch
deleted file mode 100644
index 63a49ce..0000000
--- a/target/linux/brcm2708/patches-4.4/0198-drm-vc4-Drop-error-message-on-seqno-wait-timeouts.patch
+++ /dev/null
@@ -1,27 +0,0 @@
-From e533472c91247507f73c4120a441d7844eee637a Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 25 Jan 2016 14:33:50 -0800
-Subject: [PATCH] drm/vc4: Drop error message on seqno wait timeouts.
-
-These ioctls end up getting exposed to userspace, and having normal
-user requests print DRM errors is obviously wrong. The message was
-originally to give us some idea of what happened when a hang occurred,
-but we have a DRM_INFO from reset for that.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_gem.c | 3 ---
- 1 file changed, 3 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -352,9 +352,6 @@ vc4_wait_for_seqno(struct drm_device *de
- finish_wait(&vc4->job_wait_queue, &wait);
- trace_vc4_wait_for_seqno_end(dev, seqno);
-
-- if (ret && ret != -ERESTARTSYS)
-- DRM_ERROR("timeout waiting for render thread idle\n");
--
- return ret;
- }
-
diff --git a/target/linux/brcm2708/patches-4.4/0199-BCM270X_DT-Add-1-bit-SDIO-using-minimal-pins.patch b/target/linux/brcm2708/patches-4.4/0199-BCM270X_DT-Add-1-bit-SDIO-using-minimal-pins.patch
deleted file mode 100644
index 392f70b..0000000
--- a/target/linux/brcm2708/patches-4.4/0199-BCM270X_DT-Add-1-bit-SDIO-using-minimal-pins.patch
+++ /dev/null
@@ -1,81 +0,0 @@
-From 865d65a4097327385dd845260bfac37141303d2d Mon Sep 17 00:00:00 2001
-From: campag <dave-lowe at ntlworld.com>
-Date: Wed, 24 Feb 2016 16:45:42 +0000
-Subject: [PATCH] BCM270X_DT: Add 1-bit SDIO using minimal pins...
-
-... for that mode: GPIOs 22-25.
----
- arch/arm/boot/dts/overlays/README | 21 ++++++++++++++
- arch/arm/boot/dts/overlays/sdio-1bit-overlay.dts | 36 ++++++++++++++++++++++++
- 2 files changed, 57 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/sdio-1bit-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -709,6 +709,27 @@ Params: overclock_50 SD Clock
- bus_width Set the SDIO host bus width (default 4 bits)
-
-
-+Name: sdio-1bit
-+Info: Selects the bcm2835-sdhost SD/MMC driver, optionally with overclock,
-+ and enables 1-bit SDIO via GPIOs 22-25.
-+Load: dtoverlay=sdio-1bit,<param>=<val>
-+Params: overclock_50 SD Clock (in MHz) to use when the MMC framework
-+ requests 50MHz
-+
-+ sdio_overclock SDIO Clock (in MHz) to use when the MMC
-+ framework requests 50MHz
-+
-+ force_pio Disable DMA support (default off)
-+
-+ pio_limit Number of blocks above which to use DMA
-+ (default 1)
-+
-+ debug Enable debug output (default off)
-+
-+ poll_once Disable SDIO-device polling every second
-+ (default on: polling once at boot-time)
-+
-+
- Name: sdtweak
- Info: Tunes the bcm2835-sdhost SD/MMC driver
- Load: dtoverlay=sdtweak,<param>=<val>
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/sdio-1bit-overlay.dts
-@@ -0,0 +1,36 @@
-+/* Enable 1-bit SDIO from MMC interface via GPIOs 22-25. Includes sdhost overlay. */
-+
-+/include/ "sdhost-overlay.dts"
-+
-+/{
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 3 {
-+ target = <&mmc>;
-+ sdio_mmc: __overlay__ {
-+ compatible = "brcm,bcm2835-mmc";
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&sdio_pins>;
-+ non-removable;
-+ bus-width = <1>;
-+ brcm,overclock-50 = <0>;
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 4 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ sdio_pins: sdio_pins {
-+ brcm,pins = <22 23 24 25>;
-+ brcm,function = <7 7 7 7>; /* ALT3 = SD1 */
-+ brcm,pull = <0 2 2 2>;
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ poll_once = <&sdio_mmc>,"non-removable?";
-+ sdio_overclock = <&sdio_mmc>,"brcm,overclock-50:0";
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0201-Add-overlay-and-enable-support-for-QCA7000-board.patch b/target/linux/brcm2708/patches-4.4/0201-Add-overlay-and-enable-support-for-QCA7000-board.patch
deleted file mode 100644
index 7576f61..0000000
--- a/target/linux/brcm2708/patches-4.4/0201-Add-overlay-and-enable-support-for-QCA7000-board.patch
+++ /dev/null
@@ -1,127 +0,0 @@
-From 358feb7def17978e9a3c45c1971b42d36ff89545 Mon Sep 17 00:00:00 2001
-From: Michael Heimpold <michael.heimpold at i2se.com>
-Date: Fri, 29 Jan 2016 12:00:37 +0100
-Subject: [PATCH] Add overlay and enable support for QCA7000 board
-
-This adds a device tree overlay for the QCA7000 which can be used
-when attaching an I2SE's PLC Stamp micro EVK to the Raspberry Pi.
-
-This Evaluation Board embeds a QCA7000 chip, a Homeplug Green PHY
-powerline chip from Qualcomm/Atheros for the Internet of Things.
-
-This patch also enables the required QCA7000 driver module
-in the default configurations.
-
-Signed-off-by: Stefan Wahren <stefan.wahren at i2se.com>
-Signed-off-by: Michael Heimpold <michael.heimpold at i2se.com>
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 8 ++++
- arch/arm/boot/dts/overlays/qca7000-overlay.dts | 52 ++++++++++++++++++++++++++
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 5 files changed, 63 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/qca7000-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -48,6 +48,7 @@ dtbo-$(RPI_DT_OVERLAYS) += pitft28-resis
- dtbo-$(RPI_DT_OVERLAYS) += pps-gpio.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += pwm.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += pwm-2chan.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += qca7000.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += raspidac3.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += rpi-backlight.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += rpi-dac.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -625,6 +625,14 @@ Params: pin Output p
- clock PWM clock frequency (informational)
-
-
-+Name: qca7000
-+Info: I2SE's Evaluation Board for PLC Stamp micro
-+Load: dtoverlay=qca7000,<param>=<val>
-+Params: int_pin GPIO pin for interrupt signal (default 23)
-+
-+ speed SPI bus speed (default 12 MHz)
-+
-+
- Name: raspidac3
- Info: Configures the RaspiDAV Rev.3x audio card
- Load: dtoverlay=raspidac3
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/qca7000-overlay.dts
-@@ -0,0 +1,52 @@
-+// Overlay for the Qualcomm Atheros QCA7000 on I2SE's PLC Stamp micro EVK
-+// Visit: https://www.i2se.com/product/plc-stamp-micro-evk for details
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ /* needed to avoid dtc warning */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ status = "okay";
-+
-+ spidev at 0 {
-+ status = "disabled";
-+ };
-+
-+ eth1: qca7000 at 0 {
-+ compatible = "qca,qca7000";
-+ reg = <0>; /* CE0 */
-+ pinctrl-names = "default";
-+ pinctrl-0 = <ð1_pins>;
-+ interrupt-parent = <&gpio>;
-+ interrupts = <23 0x1>; /* rising edge */
-+ spi-max-frequency = <12000000>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ eth1_pins: eth1_pins {
-+ brcm,pins = <23>;
-+ brcm,function = <0>; /* in */
-+ brcm,pull = <0>; /* none */
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ int_pin = <ð1>, "interrupts:0",
-+ <ð1_pins>, "brcm,pins:0";
-+ speed = <ð1>, "spi-max-frequency:0";
-+ };
-+};
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -446,6 +446,7 @@ CONFIG_NETCONSOLE=m
- CONFIG_TUN=m
- CONFIG_VETH=m
- CONFIG_ENC28J60=m
-+CONFIG_QCA7000=m
- CONFIG_MDIO_BITBANG=m
- CONFIG_PPP=m
- CONFIG_PPP_BSDCOMP=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -439,6 +439,7 @@ CONFIG_NETCONSOLE=m
- CONFIG_TUN=m
- CONFIG_VETH=m
- CONFIG_ENC28J60=m
-+CONFIG_QCA7000=m
- CONFIG_MDIO_BITBANG=m
- CONFIG_PPP=m
- CONFIG_PPP_BSDCOMP=m
diff --git a/target/linux/brcm2708/patches-4.4/0202-serial-Take-care-starting-a-hung-up-tty-s-port.patch b/target/linux/brcm2708/patches-4.4/0202-serial-Take-care-starting-a-hung-up-tty-s-port.patch
deleted file mode 100644
index 7e14036..0000000
--- a/target/linux/brcm2708/patches-4.4/0202-serial-Take-care-starting-a-hung-up-tty-s-port.patch
+++ /dev/null
@@ -1,28 +0,0 @@
-From 5aab55736fae3c46fab5c89ff1e9a2e2bb6740d2 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Wed, 9 Mar 2016 13:28:24 +0000
-Subject: [PATCH] serial: Take care starting a hung-up tty's port
-
-tty_port_hangup sets a port's tty field to NULL (holding the port lock),
-but uart_tx_stopped, called from __uart_start (with the port lock),
-uses the tty field without checking for NULL.
-
-Change uart_tx_stopped to treat a NULL tty field as another stopped
-indication.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- include/linux/serial_core.h | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/include/linux/serial_core.h
-+++ b/include/linux/serial_core.h
-@@ -397,7 +397,7 @@ int uart_resume_port(struct uart_driver
- static inline int uart_tx_stopped(struct uart_port *port)
- {
- struct tty_struct *tty = port->state->port.tty;
-- if (tty->stopped || port->hw_stopped)
-+ if (!tty || tty->stopped || port->hw_stopped)
- return 1;
- return 0;
- }
diff --git a/target/linux/brcm2708/patches-4.4/0203-pi3-miniuart-bt-overlay-Correct-and-clarify-info.patch b/target/linux/brcm2708/patches-4.4/0203-pi3-miniuart-bt-overlay-Correct-and-clarify-info.patch
deleted file mode 100644
index 70fada1..0000000
--- a/target/linux/brcm2708/patches-4.4/0203-pi3-miniuart-bt-overlay-Correct-and-clarify-info.patch
+++ /dev/null
@@ -1,41 +0,0 @@
-From 49da60a482e61465bb7a6148232bb5a2dd48919f Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Thu, 17 Mar 2016 10:16:16 +0000
-Subject: [PATCH] pi3-miniuart-bt-overlay: Correct and clarify info
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/overlays/README | 6 ++++--
- arch/arm/boot/dts/overlays/pi3-miniuart-bt-overlay.dts | 6 ++++--
- 2 files changed, 8 insertions(+), 4 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -511,8 +511,10 @@ Name: pi3-miniuart-bt
- Info: Switch Pi3 Bluetooth function to use the mini-UART (ttyS0) and restore
- UART0/ttyAMA0 over GPIOs 14 & 15. Note that this may reduce the maximum
- usable baudrate.
-- N.B. It is also necessary to edit /lib/systemd/system/hciuart.server
-- and replace ttyAMA0 with ttyS0.
-+ N.B. It is also necessary to edit /lib/systemd/system/hciuart.service
-+ and replace ttyAMA0 with ttyS0, unless you have a system with udev rules
-+ that create /dev/serial0 and /dev/serial1, in which case use
-+ /dev/serial1 instead because it will always be correct.
- Load: dtoverlay=pi3-miniuart-bt
- Params: <None>
-
---- a/arch/arm/boot/dts/overlays/pi3-miniuart-bt-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/pi3-miniuart-bt-overlay.dts
-@@ -5,8 +5,10 @@
- UART0/ttyAMA0 over GPIOs 14 & 15. Note that this may reduce the maximum
- usable baudrate.
-
-- It is also necessary to edit /lib/systemd/system/hciuart.server and
-- replace ttyAMA0 with ttyS0.
-+ It is also necessary to edit /lib/systemd/system/hciuart.service and
-+ replace ttyAMA0 with ttyS0, unless you have a system with udev rules
-+ that create /dev/serial0 and /dev/serial1, in which case use /dev/serial1
-+ instead because it will always be correct.
-
- If cmdline.txt uses the alias serial0 to refer to the user-accessable port
- then the firmware will replace with the appropriate port whether or not
diff --git a/target/linux/brcm2708/patches-4.4/0204-pwm-overlays-Params-must-have-in-overlay-targets.patch b/target/linux/brcm2708/patches-4.4/0204-pwm-overlays-Params-must-have-in-overlay-targets.patch
deleted file mode 100644
index 2180035..0000000
--- a/target/linux/brcm2708/patches-4.4/0204-pwm-overlays-Params-must-have-in-overlay-targets.patch
+++ /dev/null
@@ -1,52 +0,0 @@
-From 92e2a3c84b5761a54c89f3328f72b32d86f5a03c Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Thu, 17 Mar 2016 10:41:56 +0000
-Subject: [PATCH] pwm overlays: Params must have in-overlay targets
-
----
- arch/arm/boot/dts/overlays/pwm-2chan-overlay.dts | 9 ++++++++-
- arch/arm/boot/dts/overlays/pwm-overlay.dts | 9 ++++++++-
- 2 files changed, 16 insertions(+), 2 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/pwm-2chan-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/pwm-2chan-overlay.dts
-@@ -36,11 +36,18 @@ N.B.:
- };
- };
-
-+ fragment at 2 {
-+ target = <&clk_pwm>;
-+ frag2: __overlay__ {
-+ clock-frequency = <100000000>;
-+ };
-+ };
-+
- __overrides__ {
- pin = <&pwm_pins>,"brcm,pins:0";
- pin2 = <&pwm_pins>,"brcm,pins:4";
- func = <&pwm_pins>,"brcm,function:0";
- func2 = <&pwm_pins>,"brcm,function:4";
-- clock = <&clk_pwm>,"clock-frequency:0";
-+ clock = <&frag2>,"clock-frequency:0";
- };
- };
---- a/arch/arm/boot/dts/overlays/pwm-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/pwm-overlay.dts
-@@ -34,9 +34,16 @@ N.B.:
- };
- };
-
-+ fragment at 2 {
-+ target = <&clk_pwm>;
-+ frag2: __overlay__ {
-+ clock-frequency = <100000000>;
-+ };
-+ };
-+
- __overrides__ {
- pin = <&pwm_pins>,"brcm,pins:0";
- func = <&pwm_pins>,"brcm,function:0";
-- clock = <&clk_pwm>,"clock-frequency:0";
-+ clock = <&frag2>,"clock-frequency:0";
- };
- };
diff --git a/target/linux/brcm2708/patches-4.4/0205-BCM270X_DT-Switch-Compute-Module-to-MMC.patch b/target/linux/brcm2708/patches-4.4/0205-BCM270X_DT-Switch-Compute-Module-to-MMC.patch
deleted file mode 100644
index e4a5e7a..0000000
--- a/target/linux/brcm2708/patches-4.4/0205-BCM270X_DT-Switch-Compute-Module-to-MMC.patch
+++ /dev/null
@@ -1,53 +0,0 @@
-From ece89176468346dc103873a021d80b8db0ced0f6 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 18 Mar 2016 13:06:29 +0000
-Subject: [PATCH] BCM270X_DT: Switch Compute Module to MMC
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/bcm2708-rpi-cm.dtsi | 17 ++++++++---------
- 1 file changed, 8 insertions(+), 9 deletions(-)
-
---- a/arch/arm/boot/dts/bcm2708-rpi-cm.dtsi
-+++ b/arch/arm/boot/dts/bcm2708-rpi-cm.dtsi
-@@ -8,9 +8,9 @@
- };
-
- &gpio {
-- sdhost_pins: sdhost_pins {
-+ mmc_pins: mmc_pins {
- brcm,pins = <48 49 50 51 52 53>;
-- brcm,function = <4>; /* alt0 */
-+ brcm,function = <7>; /* alt3 */
- };
- };
-
-@@ -22,12 +22,14 @@
- };
- };
-
--&sdhost {
-+
-+&mmc {
- pinctrl-names = "default";
-- pinctrl-0 = <&sdhost_pins>;
-- bus-width = <4>;
-+ pinctrl-0 = <&mmc_pins>;
- non-removable;
-+ bus-width = <4>;
- status = "okay";
-+ brcm,overclock-50 = <0>;
- };
-
- &fb {
-@@ -45,9 +47,6 @@
- audio = <&audio>,"status";
- watchdog = <&watchdog>,"status";
- random = <&random>,"status";
-- sd_overclock = <&sdhost>,"brcm,overclock-50:0";
-- sd_force_pio = <&sdhost>,"brcm,force-pio?";
-- sd_pio_limit = <&sdhost>,"brcm,pio-limit:0";
-- sd_debug = <&sdhost>,"brcm,debug";
-+ sd_overclock = <&mmc>,"brcm,overclock-50:0";
- };
- };
diff --git a/target/linux/brcm2708/patches-4.4/0206-dwc_otg-Don-t-free-qh-align-buffers-in-atomic-contex.patch b/target/linux/brcm2708/patches-4.4/0206-dwc_otg-Don-t-free-qh-align-buffers-in-atomic-contex.patch
deleted file mode 100644
index eddd3d5..0000000
--- a/target/linux/brcm2708/patches-4.4/0206-dwc_otg-Don-t-free-qh-align-buffers-in-atomic-contex.patch
+++ /dev/null
@@ -1,43 +0,0 @@
-From 73e49d74c2bb5ef82bf19ad1132cd127d76dede3 Mon Sep 17 00:00:00 2001
-From: P33M <P33M at github.com>
-Date: Fri, 18 Mar 2016 17:38:37 +0000
-Subject: [PATCH] dwc_otg: Don't free qh align buffers in atomic context
-
----
- drivers/usb/host/dwc_otg/dwc_otg_hcd_queue.c | 9 +++++++--
- 1 file changed, 7 insertions(+), 2 deletions(-)
-
---- a/drivers/usb/host/dwc_otg/dwc_otg_hcd_queue.c
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_hcd_queue.c
-@@ -56,6 +56,9 @@ void dwc_otg_hcd_qh_free(dwc_otg_hcd_t *
- {
- dwc_otg_qtd_t *qtd, *qtd_tmp;
- dwc_irqflags_t flags;
-+ uint32_t buf_size = 0;
-+ uint8_t *align_buf_virt = NULL;
-+ dwc_dma_t align_buf_dma;
-
- /* Free each QTD in the QTD list */
- DWC_SPINLOCK_IRQSAVE(hcd->lock, &flags);
-@@ -67,17 +70,19 @@ void dwc_otg_hcd_qh_free(dwc_otg_hcd_t *
- if (hcd->core_if->dma_desc_enable) {
- dwc_otg_hcd_qh_free_ddma(hcd, qh);
- } else if (qh->dw_align_buf) {
-- uint32_t buf_size;
- if (qh->ep_type == UE_ISOCHRONOUS) {
- buf_size = 4096;
- } else {
- buf_size = hcd->core_if->core_params->max_transfer_size;
- }
-- DWC_DMA_FREE(buf_size, qh->dw_align_buf, qh->dw_align_buf_dma);
-+ align_buf_virt = qh->dw_align_buf;
-+ align_buf_dma = qh->dw_align_buf_dma;
- }
-
- DWC_FREE(qh);
- DWC_SPINUNLOCK_IRQRESTORE(hcd->lock, flags);
-+ if (align_buf_virt)
-+ DWC_DMA_FREE(buf_size, align_buf_virt, align_buf_dma);
- return;
- }
-
diff --git a/target/linux/brcm2708/patches-4.4/0207-dwc_otg-Enable-the-hack-for-Split-Interrupt-transact.patch b/target/linux/brcm2708/patches-4.4/0207-dwc_otg-Enable-the-hack-for-Split-Interrupt-transact.patch
deleted file mode 100644
index d4bf775..0000000
--- a/target/linux/brcm2708/patches-4.4/0207-dwc_otg-Enable-the-hack-for-Split-Interrupt-transact.patch
+++ /dev/null
@@ -1,28 +0,0 @@
-From b52a34302b48c53ea5a5db4edd1778542c823085 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Mon, 21 Mar 2016 15:38:38 +0000
-Subject: [PATCH] dwc_otg: Enable the hack for Split Interrupt transactions by
- default
-
-dwc_otg.fiq_fsm_mask=0xF has long been a suggestion for users with audio stutters or other USB bandwidth issues.
-So far we are aware of many success stories but no failure caused by this setting.
-Make it a default to learn more.
-
-See: https://www.raspberrypi.org/forums/viewtopic.php?f=28&t=70437
-
-Signed-off-by: popcornmix <popcornmix at gmail.com>
----
- drivers/usb/host/dwc_otg/dwc_otg_driver.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/usb/host/dwc_otg/dwc_otg_driver.c
-+++ b/drivers/usb/host/dwc_otg/dwc_otg_driver.c
-@@ -247,7 +247,7 @@ bool fiq_fsm_enable = true;
- //Bulk split-transaction NAK holdoff in microframes
- uint16_t nak_holdoff = 8;
-
--unsigned short fiq_fsm_mask = 0x07;
-+unsigned short fiq_fsm_mask = 0x0F;
-
- /**
- * This function shows the Driver Version.
diff --git a/target/linux/brcm2708/patches-4.4/0208-BCM270X_DT-Remove-explicit-claiming-of-UART-pins.patch b/target/linux/brcm2708/patches-4.4/0208-BCM270X_DT-Remove-explicit-claiming-of-UART-pins.patch
deleted file mode 100644
index 21f3b41..0000000
--- a/target/linux/brcm2708/patches-4.4/0208-BCM270X_DT-Remove-explicit-claiming-of-UART-pins.patch
+++ /dev/null
@@ -1,89 +0,0 @@
-From 93d9ea7abe5811252560ec7ae2c5301d0bfb3c0d Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Sat, 19 Mar 2016 16:51:37 +0000
-Subject: [PATCH] BCM270X_DT: Remove explicit claiming of UART pins
-
-It is convenient to be able to map a different function to the UART
-pins (e.g. DPI for vga666) without having to disable the UART first.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/bcm2710-rpi-3-b.dts | 6 +++---
- .../boot/dts/overlays/pi3-disable-bt-overlay.dts | 10 ++++-----
- .../boot/dts/overlays/pi3-miniuart-bt-overlay.dts | 25 +++++++++++-----------
- 3 files changed, 20 insertions(+), 21 deletions(-)
-
---- a/arch/arm/boot/dts/bcm2710-rpi-3-b.dts
-+++ b/arch/arm/boot/dts/bcm2710-rpi-3-b.dts
-@@ -57,9 +57,9 @@
- };
-
- uart1_pins: uart1_pins {
-- brcm,pins = <14 15>;
-- brcm,function = <2>; /* alt5=UART1 */
-- brcm,pull = <0 2>;
-+ brcm,pins;
-+ brcm,function;
-+ brcm,pull;
- };
- };
-
---- a/arch/arm/boot/dts/overlays/pi3-disable-bt-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/pi3-disable-bt-overlay.dts
-@@ -28,13 +28,11 @@
- };
-
- fragment at 2 {
-- target = <&gpio>;
-+ target = <&uart0_pins>;
- __overlay__ {
-- uart0_pins: uart0_pins {
-- brcm,pins = <14 15>;
-- brcm,function = <4>; /* alt0 */
-- brcm,pull = <0 2>;
-- };
-+ brcm,pins;
-+ brcm,function;
-+ brcm,pull;
- };
- };
-
---- a/arch/arm/boot/dts/overlays/pi3-miniuart-bt-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/pi3-miniuart-bt-overlay.dts
-@@ -37,23 +37,24 @@
- };
-
- fragment at 2 {
-- target = <&gpio>;
-+ target = <&uart0_pins>;
- __overlay__ {
-- uart0_pins: uart0_pins {
-- brcm,pins = <14 15>;
-- brcm,function = <4>; /* alt0 */
-- brcm,pull = <0 2>;
-- };
--
-- uart1_pins: uart1_pins {
-- brcm,pins = <32 33>;
-- brcm,function = <2>; /* alt5=UART1 */
-- brcm,pull = <0 2>;
-- };
-+ brcm,pins;
-+ brcm,function;
-+ brcm,pull;
- };
- };
-
- fragment at 3 {
-+ target = <&uart1_pins>;
-+ __overlay__ {
-+ brcm,pins = <32 33>;
-+ brcm,function = <2>; /* alt5=UART1 */
-+ brcm,pull = <0 2>;
-+ };
-+ };
-+
-+ fragment at 4 {
- target-path = "/aliases";
- __overlay__ {
- serial0 = "/soc/uart at 7e201000";
diff --git a/target/linux/brcm2708/patches-4.4/0209-lirc_rpi-Lower-IR-reception-error-to-debug.patch b/target/linux/brcm2708/patches-4.4/0209-lirc_rpi-Lower-IR-reception-error-to-debug.patch
deleted file mode 100644
index 47943f1..0000000
--- a/target/linux/brcm2708/patches-4.4/0209-lirc_rpi-Lower-IR-reception-error-to-debug.patch
+++ /dev/null
@@ -1,21 +0,0 @@
-From f8ddc7db43b7757469d5dc0ad9fddef0fb702a8d Mon Sep 17 00:00:00 2001
-From: Rodrigo Freire <rfreire at rf.usersys.redhat.com>
-Date: Tue, 22 Mar 2016 12:40:33 -0300
-Subject: [PATCH] lirc_rpi: Lower IR reception error to debug
-
-Lowers a IR reception error condition message to KERNEL_DEBUG
----
- drivers/staging/media/lirc/lirc_rpi.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/staging/media/lirc/lirc_rpi.c
-+++ b/drivers/staging/media/lirc/lirc_rpi.c
-@@ -271,7 +271,7 @@ static irqreturn_t irq_handler(int i, vo
- data = PULSE_MASK; /* really long time */
- if (!(signal^sense)) {
- /* sanity check */
-- printk(KERN_WARNING LIRC_DRIVER_NAME
-+ printk(KERN_DEBUG LIRC_DRIVER_NAME
- ": AIEEEE: %d %d %lx %lx %lx %lx\n",
- signal, sense, tv.tv_sec, lasttv.tv_sec,
- tv.tv_usec, lasttv.tv_usec);
diff --git a/target/linux/brcm2708/patches-4.4/0210-vchiq_arm-Access-the-dequeue_pending-flag-locked.patch b/target/linux/brcm2708/patches-4.4/0210-vchiq_arm-Access-the-dequeue_pending-flag-locked.patch
deleted file mode 100644
index 3c2ac0b..0000000
--- a/target/linux/brcm2708/patches-4.4/0210-vchiq_arm-Access-the-dequeue_pending-flag-locked.patch
+++ /dev/null
@@ -1,58 +0,0 @@
-From 53de1d6daf22ab3d0f36ca81bb4eaec81f698886 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Wed, 23 Mar 2016 14:16:25 +0000
-Subject: [PATCH] vchiq_arm: Access the dequeue_pending flag locked
-
-Reading through this code looking for another problem (now found in userland)
-the use of dequeue_pending outside a lock didn't seem safe.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- .../misc/vc04_services/interface/vchiq_arm/vchiq_arm.c | 17 ++++++++++++-----
- 1 file changed, 12 insertions(+), 5 deletions(-)
-
---- a/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_arm.c
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_arm.c
-@@ -279,6 +279,7 @@ service_callback(VCHIQ_REASON_T reason,
- USER_SERVICE_T *user_service;
- VCHIQ_SERVICE_T *service;
- VCHIQ_INSTANCE_T instance;
-+ int skip_completion = 0;
- DEBUG_INITIALISE(g_state.local)
-
- DEBUG_TRACE(SERVICE_CALLBACK_LINE);
-@@ -345,9 +346,6 @@ service_callback(VCHIQ_REASON_T reason,
- user_service->msg_queue[user_service->msg_insert &
- (MSG_QUEUE_SIZE - 1)] = header;
- user_service->msg_insert++;
-- spin_unlock(&msg_queue_spinlock);
--
-- up(&user_service->insert_event);
-
- /* If there is a thread waiting in DEQUEUE_MESSAGE, or if
- ** there is a MESSAGE_AVAILABLE in the completion queue then
-@@ -356,13 +354,22 @@ service_callback(VCHIQ_REASON_T reason,
- if (((user_service->message_available_pos -
- instance->completion_remove) >= 0) ||
- user_service->dequeue_pending) {
-- DEBUG_TRACE(SERVICE_CALLBACK_LINE);
- user_service->dequeue_pending = 0;
-- return VCHIQ_SUCCESS;
-+ skip_completion = 1;
- }
-
-+ spin_unlock(&msg_queue_spinlock);
-+
-+ up(&user_service->insert_event);
-+
- header = NULL;
- }
-+
-+ if (skip_completion) {
-+ DEBUG_TRACE(SERVICE_CALLBACK_LINE);
-+ return VCHIQ_SUCCESS;
-+ }
-+
- DEBUG_TRACE(SERVICE_CALLBACK_LINE);
-
- return add_completion(instance, reason, header, user_service,
diff --git a/target/linux/brcm2708/patches-4.4/0211-BCM270X_DT-Add-pi3-act-led-overlay.patch b/target/linux/brcm2708/patches-4.4/0211-BCM270X_DT-Add-pi3-act-led-overlay.patch
deleted file mode 100644
index a1d3161..0000000
--- a/target/linux/brcm2708/patches-4.4/0211-BCM270X_DT-Add-pi3-act-led-overlay.patch
+++ /dev/null
@@ -1,94 +0,0 @@
-From 04cbc84d6a2f9e06b38932e640cb6a251040eaf0 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Wed, 23 Mar 2016 15:57:14 +0000
-Subject: [PATCH] BCM270X_DT: Add pi3-act-led overlay
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 19 +++++++++++++++
- arch/arm/boot/dts/overlays/pi3-act-led-overlay.dts | 27 ++++++++++++++++++++++
- 3 files changed, 47 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/pi3-act-led-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -39,6 +39,7 @@ dtbo-$(RPI_DT_OVERLAYS) += mcp2515-can0.
- dtbo-$(RPI_DT_OVERLAYS) += mcp2515-can1.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += mmc.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += mz61581.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += pi3-act-led.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += pi3-disable-bt.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += pi3-miniuart-bt.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += piscreen.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -136,12 +136,14 @@ Params:
-
- act_led_activelow Set to "on" to invert the sense of the LED
- (default "off")
-+ N.B. For Pi3 see pi3-act-led overlay.
-
- act_led_gpio Set which GPIO to use for the activity LED
- (in case you want to connect it to an external
- device)
- (default "16" on a non-Plus board, "47" on a
- Plus or Pi 2)
-+ N.B. For Pi3 see pi3-act-led overlay.
-
- pwr_led_trigger
- pwr_led_activelow
-@@ -499,6 +501,23 @@ Params: speed Display
- [ The pcf8563-rtc overlay has been deleted. See i2c-rtc. ]
-
-
-+Name: pi3-act-led
-+Info: Pi3 uses a GPIO expander to drive the LEDs which can only be accessed
-+ from the VPU. There is a special driver for this with a separate DT
-+ node, which has the unfortunate consequence of breaking the
-+ act_led_gpio and act_led_activelow dtparams.
-+ This overlay changes the GPIO controller back to the standard one and
-+ restores the dtparams.
-+Load: dtoverlay=pi3-act-led,<param>=<val>
-+Params: activelow Set to "on" to invert the sense of the LED
-+ (default "off")
-+
-+ gpio Set which GPIO to use for the activity LED
-+ (in case you want to connect it to an external
-+ device)
-+ REQUIRED
-+
-+
- Name: pi3-disable-bt
- Info: Disable Pi3 Bluetooth and restore UART0/ttyAMA0 over GPIOs 14 & 15
- N.B. To disable the systemd service that initialises the modem so it
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/pi3-act-led-overlay.dts
-@@ -0,0 +1,27 @@
-+/dts-v1/;
-+/plugin/;
-+
-+/* Pi3 uses a GPIO expander to drive the LEDs which can only be accessed
-+ from the VPU. There is a special driver for this with a separate DT node,
-+ which has the unfortunate consequence of breaking the act_led_gpio and
-+ act_led_activelow dtparams.
-+
-+ This overlay changes the GPIO controller back to the standard one and
-+ restores the dtparams.
-+*/
-+
-+/{
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&act_led>;
-+ frag0: __overlay__ {
-+ gpios = <&gpio 0 0>;
-+ };
-+ };
-+
-+ __overrides__ {
-+ gpio = <&frag0>,"gpios:4";
-+ activelow = <&frag0>,"gpios:8";
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0212-vchiq_arm-Service-callbacks-must-not-fail.patch b/target/linux/brcm2708/patches-4.4/0212-vchiq_arm-Service-callbacks-must-not-fail.patch
deleted file mode 100644
index eae0f0f..0000000
--- a/target/linux/brcm2708/patches-4.4/0212-vchiq_arm-Service-callbacks-must-not-fail.patch
+++ /dev/null
@@ -1,26 +0,0 @@
-From b88115ca91107f35ed28e4dfd2f2fdd18d3707fe Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Wed, 23 Mar 2016 20:53:47 +0000
-Subject: [PATCH] vchiq_arm: Service callbacks must not fail
-
-Service callbacks are not allowed to return an error. The internal callback
-that delivers events and messages to user tasks does not enqueue them if
-the service is closing, but this is not an error and should not be
-reported as such.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- drivers/misc/vc04_services/interface/vchiq_arm/vchiq_arm.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_arm.c
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_arm.c
-@@ -224,7 +224,7 @@ add_completion(VCHIQ_INSTANCE_T instance
- } else if (instance->closing) {
- vchiq_log_info(vchiq_arm_log_level,
- "service_callback closing");
-- return VCHIQ_ERROR;
-+ return VCHIQ_SUCCESS;
- }
- DEBUG_TRACE(SERVICE_CALLBACK_LINE);
- }
diff --git a/target/linux/brcm2708/patches-4.4/0213-Add-configs-and-overlay-for-PCA9548-I2C-mux.patch b/target/linux/brcm2708/patches-4.4/0213-Add-configs-and-overlay-for-PCA9548-I2C-mux.patch
deleted file mode 100644
index 28db3d1..0000000
--- a/target/linux/brcm2708/patches-4.4/0213-Add-configs-and-overlay-for-PCA9548-I2C-mux.patch
+++ /dev/null
@@ -1,133 +0,0 @@
-From 29a3c1c4b42969b487d1212128a2bdf4135fedb9 Mon Sep 17 00:00:00 2001
-From: Dave Stevenson <6by9 at users.noreply.github.com>
-Date: Thu, 17 Mar 2016 18:16:16 +0000
-Subject: [PATCH] Add configs and overlay for PCA9548 I2C mux
-
-Adds kernel configs for I2C muxes and a dt overlay for PCA9548
-that adds the 8 muxed I2C buses and mux device.
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 6 ++
- .../boot/dts/overlays/i2c-mux-pca9548a-overlay.dts | 67 ++++++++++++++++++++++
- arch/arm/configs/bcm2709_defconfig | 2 +
- arch/arm/configs/bcmrpi_defconfig | 2 +
- 5 files changed, 78 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/i2c-mux-pca9548a-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -29,6 +29,7 @@ dtbo-$(RPI_DT_OVERLAYS) += hy28a.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += hy28b.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c-rtc.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c-gpio.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += i2c-mux-pca9548a.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c0-bcm2708.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c1-bcm2708.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2s-mmap.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -360,6 +360,12 @@ Params: i2c_gpio_sda GPIO use
- (default "2" = ~100kHz)
-
-
-+Name: i2c-mux-pca9548a
-+Info: Adds support for an NXP PCA9548A I2C multiplexer on i2c_arm
-+Load: dtoverlay=i2c-mux-pca9548a,<param>=<val>
-+Params: addr I2C address of PCA9548A (default 0x70)
-+
-+
- Name: i2c-rtc
- Info: Adds support for a number of I2C Real Time Clock devices
- Load: dtoverlay=i2c-rtc,<param>=<val>
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/i2c-mux-pca9548a-overlay.dts
-@@ -0,0 +1,67 @@
-+// Definitions for NXP PCA9548A I2C mux on ARM I2C bus.
-+/dts-v1/;
-+/plugin/;
-+
-+/{
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&i2c_arm>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ i2cmux: mux at 70 {
-+ compatible = "nxp,pca9548";
-+ reg = <0x70>;
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ i2c at 0 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <0>;
-+ };
-+ i2c at 1 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <1>;
-+ };
-+ i2c at 2 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <2>;
-+ };
-+ i2c at 3 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <3>;
-+ };
-+ i2c at 4 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <4>;
-+ };
-+ i2c at 5 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <5>;
-+ };
-+ i2c at 6 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <6>;
-+ };
-+ i2c at 7 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <7>;
-+ };
-+ };
-+ };
-+ };
-+ __overrides__ {
-+ addr = <&i2cmux>,"reg:0";
-+ };
-+};
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -600,6 +600,8 @@ CONFIG_I2C=y
- CONFIG_I2C_CHARDEV=m
- CONFIG_I2C_BCM2708=m
- CONFIG_I2C_GPIO=m
-+CONFIG_I2C_MUX=m
-+CONFIG_I2C_MUX_PCA954x=m
- CONFIG_SPI=y
- CONFIG_SPI_BCM2835=m
- CONFIG_SPI_BCM2835AUX=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -593,6 +593,8 @@ CONFIG_I2C=y
- CONFIG_I2C_CHARDEV=m
- CONFIG_I2C_BCM2708=m
- CONFIG_I2C_GPIO=m
-+CONFIG_I2C_MUX=m
-+CONFIG_I2C_MUX_PCA954x=m
- CONFIG_SPI=y
- CONFIG_SPI_BCM2835=m
- CONFIG_SPI_BCM2835AUX=m
diff --git a/target/linux/brcm2708/patches-4.4/0214-BCM270X_DT-Add-DS1339-to-i2c-rtc-overlay.patch b/target/linux/brcm2708/patches-4.4/0214-BCM270X_DT-Add-DS1339-to-i2c-rtc-overlay.patch
deleted file mode 100644
index 5356373..0000000
--- a/target/linux/brcm2708/patches-4.4/0214-BCM270X_DT-Add-DS1339-to-i2c-rtc-overlay.patch
+++ /dev/null
@@ -1,58 +0,0 @@
-From 147681567d5d5d3032c749f4203630677f278df8 Mon Sep 17 00:00:00 2001
-From: Nicolas Boullis <nboullis at debian.org>
-Date: Wed, 23 Mar 2016 23:40:15 +0100
-Subject: [PATCH] BCM270X_DT: Add DS1339 to i2c-rtc overlay
-
----
- arch/arm/boot/dts/overlays/README | 4 ++++
- arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts | 8 ++++++++
- 2 files changed, 12 insertions(+)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -371,6 +371,8 @@ Info: Adds support for a number of I2C
- Load: dtoverlay=i2c-rtc,<param>=<val>
- Params: ds1307 Select the DS1307 device
-
-+ ds1339 Select the DS1339 device
-+
- ds3231 Select the DS3231 device
-
- mcp7941x Select the MCP7941x device
-@@ -381,6 +383,8 @@ Params: ds1307 Select t
-
- pcf8563 Select the PCF8563 device
-
-+ trickle-resistor-ohms Resistor value for trickle charge (DS1339-only)
-+
-
- Name: i2c0-bcm2708
- Info: Enable the i2c_bcm2708 driver for the i2c0 bus
---- a/arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts
-@@ -17,6 +17,12 @@
- reg = <0x68>;
- status = "disable";
- };
-+ ds1339: ds1339 at 68 {
-+ compatible = "dallas,ds1339";
-+ trickle-resistor-ohms = <0>;
-+ reg = <0x68>;
-+ status = "disable";
-+ };
- mcp7941x: mcp7941x at 6f {
- compatible = "microchip,mcp7941x";
- reg = <0x6f>;
-@@ -46,10 +52,12 @@
- };
- __overrides__ {
- ds1307 = <&ds1307>,"status";
-+ ds1339 = <&ds1339>,"status";
- ds3231 = <&ds3231>,"status";
- mcp7941x = <&mcp7941x>,"status";
- pcf2127 = <&pcf2127>,"status";
- pcf8523 = <&pcf8523>,"status";
- pcf8563 = <&pcf8563>,"status";
-+ trickle-resistor-ohms = <&ds1339>,"trickle-resistor-ohms:0";
- };
- };
diff --git a/target/linux/brcm2708/patches-4.4/0215-copy_from_user-CPU_SW_DOMAIN_PAN-compatibility.patch b/target/linux/brcm2708/patches-4.4/0215-copy_from_user-CPU_SW_DOMAIN_PAN-compatibility.patch
deleted file mode 100644
index 2d8b374..0000000
--- a/target/linux/brcm2708/patches-4.4/0215-copy_from_user-CPU_SW_DOMAIN_PAN-compatibility.patch
+++ /dev/null
@@ -1,53 +0,0 @@
-From cfe94ad9e10d75790f783296006c60fb89beb321 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Tue, 29 Mar 2016 15:32:30 +0100
-Subject: [PATCH] copy_from_user: CPU_SW_DOMAIN_PAN compatibility
-
-The downstream copy_from_user acceleration must also play nice with
-CONFIG_CPU_SW_DOMAIN_PAN.
-
-See: https://github.com/raspberrypi/linux/issues/1381
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/lib/uaccess_with_memcpy.c | 14 +++++++++++---
- 1 file changed, 11 insertions(+), 3 deletions(-)
-
---- a/arch/arm/lib/uaccess_with_memcpy.c
-+++ b/arch/arm/lib/uaccess_with_memcpy.c
-@@ -186,6 +186,7 @@ out:
- unsigned long noinline
- __copy_from_user_memcpy(void *to, const void __user *from, unsigned long n)
- {
-+ unsigned long ua_flags;
- int atomic;
-
- if (unlikely(segment_eq(get_fs(), KERNEL_DS))) {
-@@ -217,7 +218,9 @@ __copy_from_user_memcpy(void *to, const
- if (tocopy > n)
- tocopy = n;
-
-+ ua_flags = uaccess_save_and_enable();
- memcpy(to, (const void *)from, tocopy);
-+ uaccess_restore(ua_flags);
- to += tocopy;
- from += tocopy;
- n -= tocopy;
-@@ -261,9 +264,14 @@ arm_copy_from_user(void *to, const void
- * With frame pointer disabled, tail call optimization kicks in
- * as well making this test almost invisible.
- */
-- if (n < COPY_FROM_USER_THRESHOLD)
-- return __copy_from_user_std(to, from, n);
-- return __copy_from_user_memcpy(to, from, n);
-+ if (n < COPY_TO_USER_THRESHOLD) {
-+ unsigned long ua_flags = uaccess_save_and_enable();
-+ n = __copy_from_user_std(to, from, n);
-+ uaccess_restore(ua_flags);
-+ } else {
-+ n = __copy_from_user_memcpy(to, from, n);
-+ }
-+ return n;
- }
-
- static unsigned long noinline
diff --git a/target/linux/brcm2708/patches-4.4/0216-bcm2835-sdhost-Adjust-to-core-clock-changes.patch b/target/linux/brcm2708/patches-4.4/0216-bcm2835-sdhost-Adjust-to-core-clock-changes.patch
deleted file mode 100644
index cfc32c0..0000000
--- a/target/linux/brcm2708/patches-4.4/0216-bcm2835-sdhost-Adjust-to-core-clock-changes.patch
+++ /dev/null
@@ -1,339 +0,0 @@
-From afa73f51ed48ae715560e200edcdb7cc85a1e43b Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Wed, 30 Mar 2016 16:33:09 +0100
-Subject: [PATCH] bcm2835-sdhost: Adjust to core clock changes
-
-The SDHOST block uses the core clock, so previously it has been
-necessary to prevent the core clock from changing in order to maintain
-performance and prevent accidental SD bus overclocking.
-
-With this patch the sdhost driver is notified of clock changes, allowing
-it to delay them while an SD access is outstanding and to delay new SD
-accesses while the clock is changing. This feature is disabled in the
-case where the core frequency can never change.
-
-Now that the driver copes with changes to the core clock, it is safe
-to disable the io_is_busy feature of the on-demand governor.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- drivers/mmc/host/Kconfig | 1 +
- drivers/mmc/host/bcm2835-sdhost.c | 140 ++++++++++++++++++++++++++++++++------
- 2 files changed, 119 insertions(+), 22 deletions(-)
-
---- a/drivers/mmc/host/Kconfig
-+++ b/drivers/mmc/host/Kconfig
-@@ -36,6 +36,7 @@ config MMC_BCM2835_PIO_DMA_BARRIER
- config MMC_BCM2835_SDHOST
- tristate "Support for the SDHost controller on BCM2708/9"
- depends on MACH_BCM2708 || MACH_BCM2709 || ARCH_BCM2835
-+ depends on RASPBERRYPI_FIRMWARE
- help
- This selects the SDHost controller on BCM2835/6.
-
---- a/drivers/mmc/host/bcm2835-sdhost.c
-+++ b/drivers/mmc/host/bcm2835-sdhost.c
-@@ -50,6 +50,10 @@
- #include <linux/of_dma.h>
- #include <linux/time.h>
- #include <linux/workqueue.h>
-+#include <linux/cpufreq.h>
-+#include <linux/semaphore.h>
-+#include <soc/bcm2835/raspberrypi-firmware.h>
-+
-
- #define DRIVER_NAME "sdhost-bcm2835"
-
-@@ -136,6 +140,8 @@
-
- #define MHZ 1000000
-
-+#define RPI_FIRMWARE_CLOCK_CORE 4
-+
-
- struct bcm2835_host {
- spinlock_t lock;
-@@ -151,7 +157,9 @@ struct bcm2835_host {
-
- bool slow_card; /* Force 11-bit divisor */
-
-- unsigned int max_clk; /* Max possible freq */
-+ unsigned int max_clk; /* Max src clock freq */
-+ unsigned int min_clk; /* Min src clock freq */
-+ unsigned int cur_clk; /* Current src clock freq */
-
- struct tasklet_struct finish_tasklet; /* Tasklet structures */
-
-@@ -183,6 +191,7 @@ struct bcm2835_host {
- unsigned int use_sbc:1; /* Send CMD23 */
-
- unsigned int debug:1; /* Enable debug output */
-+ unsigned int variable_clock:1; /* The core clock may change */
-
- /*DMA part*/
- struct dma_chan *dma_chan_rxtx; /* DMA channel for reads and writes */
-@@ -208,6 +217,9 @@ struct bcm2835_host {
- u32 pio_limit; /* Maximum block count for PIO (0 = always DMA) */
-
- u32 sectors; /* Cached card size in sectors */
-+
-+ struct notifier_block cpufreq_nb; /* The cpufreq callback list item */
-+ struct semaphore cpufreq_semaphore; /* Interlock between SD activity and cpufreq changes */
- };
-
- #if ENABLE_LOG
-@@ -227,6 +239,10 @@ static u32 sdhost_log_idx;
- static spinlock_t log_lock;
- static void __iomem *timer_base;
-
-+static int bcm2835_sdhost_cpufreq_callback(struct notifier_block *nb,
-+ unsigned long action, void *data);
-+static unsigned int get_core_clock(unsigned int mode);
-+
- #define LOG_ENTRIES (256*1)
- #define LOG_SIZE (sizeof(LOG_ENTRY_T)*LOG_ENTRIES)
-
-@@ -448,20 +464,14 @@ static void bcm2835_sdhost_reset(struct
-
- static void bcm2835_sdhost_set_ios(struct mmc_host *mmc, struct mmc_ios *ios);
-
--static void bcm2835_sdhost_init(struct bcm2835_host *host, int soft)
-+static void bcm2835_sdhost_init(struct bcm2835_host *host)
- {
-- pr_debug("bcm2835_sdhost_init(%d)\n", soft);
-+ pr_debug("bcm2835_sdhost_init()\n");
-
- /* Set interrupt enables */
- host->hcfg = SDHCFG_BUSY_IRPT_EN;
-
- bcm2835_sdhost_reset_internal(host);
--
-- if (soft) {
-- /* force clock reconfiguration */
-- host->clock = 0;
-- bcm2835_sdhost_set_ios(host->mmc, &host->mmc->ios);
-- }
- }
-
- static void bcm2835_sdhost_wait_transfer_complete(struct bcm2835_host *host)
-@@ -1499,10 +1509,10 @@ static irqreturn_t bcm2835_sdhost_irq(in
- return result;
- }
-
--void bcm2835_sdhost_set_clock(struct bcm2835_host *host, unsigned int clock)
-+void bcm2835_sdhost_set_clock(struct bcm2835_host *host)
- {
- int div = 0; /* Initialized for compiler warning */
-- unsigned int input_clock = clock;
-+ unsigned int clock = host->clock;
-
- if (host->debug)
- pr_info("%s: set_clock(%d)\n", mmc_hostname(host->mmc), clock);
-@@ -1543,17 +1553,17 @@ void bcm2835_sdhost_set_clock(struct bcm
- return;
- }
-
-- div = host->max_clk / clock;
-+ div = host->cur_clk / clock;
- if (div < 2)
- div = 2;
-- if ((host->max_clk / div) > clock)
-+ if ((host->cur_clk / div) > clock)
- div++;
- div -= 2;
-
- if (div > SDCDIV_MAX_CDIV)
- div = SDCDIV_MAX_CDIV;
-
-- clock = host->max_clk / (div + 2);
-+ clock = host->cur_clk / (div + 2);
- host->mmc->actual_clock = clock;
-
- /* Calibrate some delays */
-@@ -1561,7 +1571,7 @@ void bcm2835_sdhost_set_clock(struct bcm
- host->ns_per_fifo_word = (1000000000/clock) *
- ((host->mmc->caps & MMC_CAP_4_BIT_DATA) ? 8 : 32);
-
-- if (clock > input_clock) {
-+ if (clock > host->clock) {
- /* Save the closest value, to make it easier
- to reduce in the event of error */
- host->overclock_50 = (clock/MHZ);
-@@ -1587,9 +1597,9 @@ void bcm2835_sdhost_set_clock(struct bcm
- bcm2835_sdhost_write(host, host->mmc->actual_clock/2, SDTOUT);
-
- if (host->debug)
-- pr_info("%s: clock=%d -> max_clk=%d, cdiv=%x (actual clock %d)\n",
-- mmc_hostname(host->mmc), input_clock,
-- host->max_clk, host->cdiv, host->mmc->actual_clock);
-+ pr_info("%s: clock=%d -> cur_clk=%d, cdiv=%x (actual clock %d)\n",
-+ mmc_hostname(host->mmc), host->clock,
-+ host->cur_clk, host->cdiv, host->mmc->actual_clock);
- }
-
- static void bcm2835_sdhost_request(struct mmc_host *mmc, struct mmc_request *mrq)
-@@ -1638,6 +1648,13 @@ static void bcm2835_sdhost_request(struc
- (mrq->data->blocks > host->pio_limit))
- bcm2835_sdhost_prepare_dma(host, mrq->data);
-
-+ if (host->variable_clock &&
-+ (down_killable(&host->cpufreq_semaphore) != 0)) {
-+ mrq->cmd->error = -EINTR;
-+ mmc_request_done(mmc, mrq);
-+ return;
-+ }
-+
- spin_lock_irqsave(&host->lock, flags);
-
- WARN_ON(host->mrq != NULL);
-@@ -1687,6 +1704,52 @@ static void bcm2835_sdhost_request(struc
- spin_unlock_irqrestore(&host->lock, flags);
- }
-
-+static int bcm2835_sdhost_cpufreq_callback(struct notifier_block *nb,
-+ unsigned long action, void *data)
-+{
-+ struct cpufreq_freqs *freq = data;
-+ struct bcm2835_host *host;
-+
-+ host = container_of(nb, struct bcm2835_host, cpufreq_nb);
-+
-+ if (freq->cpu == 0) {
-+ switch (action) {
-+ case CPUFREQ_PRECHANGE:
-+ if (down_killable(&host->cpufreq_semaphore) != 0)
-+ return NOTIFY_BAD;
-+ break;
-+ case CPUFREQ_POSTCHANGE:
-+ if (freq->new > freq->old)
-+ host->cur_clk = host->max_clk;
-+ else
-+ host->cur_clk = host->min_clk;
-+ bcm2835_sdhost_set_clock(host);
-+ up(&host->cpufreq_semaphore);
-+ break;
-+ default:
-+ break;
-+ }
-+ }
-+ return NOTIFY_OK;
-+}
-+
-+static unsigned int get_core_clock(unsigned int mode)
-+{
-+ struct rpi_firmware *fw = rpi_firmware_get(NULL);
-+ struct {
-+ u32 id;
-+ u32 val;
-+ } packet;
-+ int ret;
-+
-+ packet.id = RPI_FIRMWARE_CLOCK_CORE;
-+ ret = rpi_firmware_property(fw, mode, &packet, sizeof(packet));
-+ if (ret)
-+ return 0;
-+
-+ return packet.val;
-+}
-+
- static void bcm2835_sdhost_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
- {
-
-@@ -1700,13 +1763,16 @@ static void bcm2835_sdhost_set_ios(struc
- ios->clock, ios->power_mode, ios->bus_width,
- ios->timing, ios->signal_voltage, ios->drv_type);
-
-+ if (ios->clock && !host->cur_clk)
-+ host->cur_clk = get_core_clock(RPI_FIRMWARE_GET_CLOCK_RATE);
-+
- spin_lock_irqsave(&host->lock, flags);
-
- log_event("IOS<", ios->clock, 0);
-
- if (!ios->clock || ios->clock != host->clock) {
-- bcm2835_sdhost_set_clock(host, ios->clock);
- host->clock = ios->clock;
-+ bcm2835_sdhost_set_clock(host);
- }
-
- /* set bus width */
-@@ -1795,7 +1861,7 @@ static void bcm2835_sdhost_tasklet_finis
- host->overclock_50--;
- pr_warn("%s: reducing overclock due to errors\n",
- mmc_hostname(host->mmc));
-- bcm2835_sdhost_set_clock(host,50*MHZ);
-+ bcm2835_sdhost_set_clock(host);
- mrq->cmd->error = -EILSEQ;
- mrq->cmd->retries = 1;
- }
-@@ -1813,6 +1879,9 @@ static void bcm2835_sdhost_tasklet_finis
-
- spin_unlock_irqrestore(&host->lock, flags);
-
-+ if (host->variable_clock)
-+ up(&host->cpufreq_semaphore);
-+
- if (terminate_chan)
- {
- int err = dmaengine_terminate_all(terminate_chan);
-@@ -1915,10 +1984,10 @@ int bcm2835_sdhost_add_host(struct bcm28
- setup_timer(&host->timer, bcm2835_sdhost_timeout,
- (unsigned long)host);
-
-- bcm2835_sdhost_init(host, 0);
-+ bcm2835_sdhost_init(host);
-
- ret = request_irq(host->irq, bcm2835_sdhost_irq, 0 /*IRQF_SHARED*/,
-- mmc_hostname(mmc), host);
-+ mmc_hostname(mmc), host);
- if (ret) {
- pr_err("%s: failed to request IRQ %d: %d\n",
- mmc_hostname(mmc), host->irq, ret);
-@@ -1953,6 +2022,7 @@ static int bcm2835_sdhost_probe(struct p
- struct bcm2835_host *host;
- struct mmc_host *mmc;
- const __be32 *addr;
-+ unsigned int max_clk;
- int ret;
-
- pr_debug("bcm2835_sdhost_probe\n");
-@@ -2062,6 +2132,28 @@ static int bcm2835_sdhost_probe(struct p
- if (ret)
- goto err;
-
-+ /* Query the core clock frequencies */
-+ host->min_clk = get_core_clock(RPI_FIRMWARE_GET_MIN_CLOCK_RATE);
-+ max_clk = get_core_clock(RPI_FIRMWARE_GET_MAX_CLOCK_RATE);
-+ if (max_clk != host->max_clk) {
-+ pr_warn("%s: Expected max clock %d, found %d\n",
-+ mmc_hostname(mmc), host->max_clk, max_clk);
-+ host->max_clk = max_clk;
-+ }
-+
-+ if (host->min_clk != host->max_clk) {
-+ host->cpufreq_nb.notifier_call =
-+ bcm2835_sdhost_cpufreq_callback;
-+ sema_init(&host->cpufreq_semaphore, 1);
-+ cpufreq_register_notifier(&host->cpufreq_nb,
-+ CPUFREQ_TRANSITION_NOTIFIER);
-+ host->variable_clock = 1;
-+ host->cur_clk = 0; /* Get this later */
-+ } else {
-+ host->variable_clock = 0;
-+ host->cur_clk = host->max_clk;
-+ }
-+
- platform_set_drvdata(pdev, host);
-
- pr_debug("bcm2835_sdhost_probe -> OK\n");
-@@ -2081,6 +2173,10 @@ static int bcm2835_sdhost_remove(struct
-
- pr_debug("bcm2835_sdhost_remove\n");
-
-+ if (host->variable_clock)
-+ cpufreq_unregister_notifier(&host->cpufreq_nb,
-+ CPUFREQ_TRANSITION_NOTIFIER);
-+
- mmc_remove_host(host->mmc);
-
- bcm2835_sdhost_set_power(host, false);
diff --git a/target/linux/brcm2708/patches-4.4/0217-BCM270X_DT-Document-hazards-of-sdhost-overlay.patch b/target/linux/brcm2708/patches-4.4/0217-BCM270X_DT-Document-hazards-of-sdhost-overlay.patch
deleted file mode 100644
index 3e75aa9..0000000
--- a/target/linux/brcm2708/patches-4.4/0217-BCM270X_DT-Document-hazards-of-sdhost-overlay.patch
+++ /dev/null
@@ -1,34 +0,0 @@
-From 9a865e38d598c4495e34f3c8f23680a946c68f3b Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Wed, 30 Mar 2016 17:07:15 +0100
-Subject: [PATCH] BCM270X_DT: Document hazards of sdhost overlay
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/overlays/README | 8 +++++++-
- 1 file changed, 7 insertions(+), 1 deletion(-)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -712,7 +712,11 @@ Params: <None>
-
-
- Name: sdhost
--Info: Selects the bcm2835-sdhost SD/MMC driver, optionally with overclock
-+Info: Selects the bcm2835-sdhost SD/MMC driver, optionally with overclock.
-+ N.B. This overlay is designed for situations where the mmc driver is
-+ the default, so it disables the other (mmc) interface - this will kill
-+ WiFi on a Pi3. If this isn't what you want, either use the sdtweak
-+ overlay or the new sd_* dtparams of the base DTBs.
- Load: dtoverlay=sdhost,<param>=<val>
- Params: overclock_50 Clock (in MHz) to use when the MMC framework
- requests 50MHz
-@@ -771,6 +775,8 @@ Params: overclock_50 SD Clock
-
- Name: sdtweak
- Info: Tunes the bcm2835-sdhost SD/MMC driver
-+ N.B. This functionality is now available via the sd_* dtparams in the
-+ base DTB.
- Load: dtoverlay=sdtweak,<param>=<val>
- Params: overclock_50 Clock (in MHz) to use when the MMC framework
- requests 50MHz
diff --git a/target/linux/brcm2708/patches-4.4/0218-cpufreq-Temporarily-ignore-io_is_busy-1.patch b/target/linux/brcm2708/patches-4.4/0218-cpufreq-Temporarily-ignore-io_is_busy-1.patch
deleted file mode 100644
index ca5c0fc..0000000
--- a/target/linux/brcm2708/patches-4.4/0218-cpufreq-Temporarily-ignore-io_is_busy-1.patch
+++ /dev/null
@@ -1,31 +0,0 @@
-From f22c5a99f10b4bc3e219c682e0eb28d2fcdbb4d0 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Wed, 30 Mar 2016 17:23:15 +0100
-Subject: [PATCH] cpufreq: Temporarily ignore io_is_busy=1
-
-To speed testing of the new sdhost driver that adapts to changes in
-core_freq, hack the on-demand governor to treat io_is_busy=1 as
-io_is_busy=0. The io_is_busy feature can still be forced using
-io_is_busy=2.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- drivers/cpufreq/cpufreq_ondemand.c | 7 ++++++-
- 1 file changed, 6 insertions(+), 1 deletion(-)
-
---- a/drivers/cpufreq/cpufreq_ondemand.c
-+++ b/drivers/cpufreq/cpufreq_ondemand.c
-@@ -307,7 +307,12 @@ static ssize_t store_io_is_busy(struct d
- ret = sscanf(buf, "%u", &input);
- if (ret != 1)
- return -EINVAL;
-- od_tuners->io_is_busy = !!input;
-+ // XXX temporary hack
-+ if (input > 1)
-+ input = 1;
-+ else
-+ input = 0;
-+ od_tuners->io_is_busy = input;
-
- /* we need to re-evaluate prev_cpu_idle */
- for_each_online_cpu(j) {
diff --git a/target/linux/brcm2708/patches-4.4/0219-Revert-cpufreq-Temporarily-ignore-io_is_busy-1.patch b/target/linux/brcm2708/patches-4.4/0219-Revert-cpufreq-Temporarily-ignore-io_is_busy-1.patch
deleted file mode 100644
index 2e258e5..0000000
--- a/target/linux/brcm2708/patches-4.4/0219-Revert-cpufreq-Temporarily-ignore-io_is_busy-1.patch
+++ /dev/null
@@ -1,26 +0,0 @@
-From 2948f9f5e47f5ed46179b3f0c79b4c97fa88dab0 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Wed, 30 Mar 2016 20:18:38 +0100
-Subject: [PATCH] Revert "cpufreq: Temporarily ignore io_is_busy=1"
-
-This reverts commit 2af1218a8a0220fec526f64d03977b8451afb4c8.
----
- drivers/cpufreq/cpufreq_ondemand.c | 7 +------
- 1 file changed, 1 insertion(+), 6 deletions(-)
-
---- a/drivers/cpufreq/cpufreq_ondemand.c
-+++ b/drivers/cpufreq/cpufreq_ondemand.c
-@@ -307,12 +307,7 @@ static ssize_t store_io_is_busy(struct d
- ret = sscanf(buf, "%u", &input);
- if (ret != 1)
- return -EINVAL;
-- // XXX temporary hack
-- if (input > 1)
-- input = 1;
-- else
-- input = 0;
-- od_tuners->io_is_busy = input;
-+ od_tuners->io_is_busy = !!input;
-
- /* we need to re-evaluate prev_cpu_idle */
- for_each_online_cpu(j) {
diff --git a/target/linux/brcm2708/patches-4.4/0220-net-sched-add-skb_at_tc_ingress-helper.patch b/target/linux/brcm2708/patches-4.4/0220-net-sched-add-skb_at_tc_ingress-helper.patch
deleted file mode 100644
index bd88fa5..0000000
--- a/target/linux/brcm2708/patches-4.4/0220-net-sched-add-skb_at_tc_ingress-helper.patch
+++ /dev/null
@@ -1,31 +0,0 @@
-From 21d7bc4d1c4680d8c1e8f14b314c3f232db3b6aa Mon Sep 17 00:00:00 2001
-From: Daniel Borkmann <daniel at iogearbox.net>
-Date: Thu, 7 Jan 2016 15:50:22 +0100
-Subject: [PATCH] net, sched: add skb_at_tc_ingress helper
-
-Add a skb_at_tc_ingress() as this will be needed elsewhere as well and
-can hide the ugly ifdef.
-
-Signed-off-by: Daniel Borkmann <daniel at iogearbox.net>
-Acked-by: Alexei Starovoitov <ast at kernel.org>
-Signed-off-by: David S. Miller <davem at davemloft.net>
----
- net/sched/cls_bpf.c | 6 +-----
- 1 file changed, 1 insertion(+), 5 deletions(-)
-
---- a/net/sched/cls_bpf.c
-+++ b/net/sched/cls_bpf.c
-@@ -79,12 +79,8 @@ static int cls_bpf_classify(struct sk_bu
- struct tcf_result *res)
- {
- struct cls_bpf_head *head = rcu_dereference_bh(tp->root);
-+ bool at_ingress = skb_at_tc_ingress(skb);
- struct cls_bpf_prog *prog;
--#ifdef CONFIG_NET_CLS_ACT
-- bool at_ingress = G_TC_AT(skb->tc_verd) & AT_INGRESS;
--#else
-- bool at_ingress = false;
--#endif
- int ret = -1;
-
- if (unlikely(!skb_mac_header_was_set(skb)))
diff --git a/target/linux/brcm2708/patches-4.4/0222-bcm2835-sdhost-Precalc-divisors-and-overclocks.patch b/target/linux/brcm2708/patches-4.4/0222-bcm2835-sdhost-Precalc-divisors-and-overclocks.patch
deleted file mode 100644
index a35c8b1..0000000
--- a/target/linux/brcm2708/patches-4.4/0222-bcm2835-sdhost-Precalc-divisors-and-overclocks.patch
+++ /dev/null
@@ -1,270 +0,0 @@
-From 152daaa4a44dfa67ec4c975d0f3446b38fe047bd Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Thu, 31 Mar 2016 15:44:53 +0100
-Subject: [PATCH] bcm2835-sdhost: Precalc divisors and overclocks
-
-Recalculating the clock divisors when the core clock changes is wasteful
-and makes it harder to manage the overclock settings. Instead,
-precalculate them and only report significant changes.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- drivers/mmc/host/bcm2835-sdhost.c | 152 ++++++++++++++++++++++----------------
- 1 file changed, 88 insertions(+), 64 deletions(-)
-
---- a/drivers/mmc/host/bcm2835-sdhost.c
-+++ b/drivers/mmc/host/bcm2835-sdhost.c
-@@ -154,12 +154,15 @@ struct bcm2835_host {
- u32 pio_timeout; /* In jiffies */
-
- int clock; /* Current clock speed */
-+ int clocks[2];
-
- bool slow_card; /* Force 11-bit divisor */
-
- unsigned int max_clk; /* Max src clock freq */
-- unsigned int min_clk; /* Min src clock freq */
-- unsigned int cur_clk; /* Current src clock freq */
-+ unsigned int src_clks[2]; /* Min/max src clock freqs */
-+ unsigned int cur_clk_idx; /* Index of current clock */
-+ unsigned int next_clk_idx; /* Next clock index */
-+ unsigned int cdivs[2];
-
- struct tasklet_struct finish_tasklet; /* Tasklet structures */
-
-@@ -213,7 +216,7 @@ struct bcm2835_host {
- u32 delay_after_stop; /* minimum time between stop and subsequent data transfer */
- u32 delay_after_this_stop; /* minimum time between this stop and subsequent data transfer */
- u32 overclock_50; /* frequency to use when 50MHz is requested (in MHz) */
-- u32 overclock; /* Current frequency if overclocked, else zero */
-+ u32 prev_overclock_50;
- u32 pio_limit; /* Maximum block count for PIO (0 = always DMA) */
-
- u32 sectors; /* Cached card size in sectors */
-@@ -1509,10 +1512,35 @@ static irqreturn_t bcm2835_sdhost_irq(in
- return result;
- }
-
-+static void bcm2835_sdhost_select_clock(struct bcm2835_host *host, int idx)
-+{
-+ unsigned int clock = host->clocks[idx];
-+ unsigned int cdiv = host->cdivs[idx];
-+
-+ host->mmc->actual_clock = clock;
-+ host->ns_per_fifo_word = (1000000000/clock) *
-+ ((host->mmc->caps & MMC_CAP_4_BIT_DATA) ? 8 : 32);
-+
-+ host->cdiv = cdiv;
-+ bcm2835_sdhost_write(host, host->cdiv, SDCDIV);
-+
-+ /* Set the timeout to 500ms */
-+ bcm2835_sdhost_write(host, clock/2, SDTOUT);
-+
-+ host->cur_clk_idx = host->next_clk_idx = idx;
-+
-+ if (host->debug)
-+ pr_info("%s: clock=%d -> src_clk=%d, cdiv=%x (actual %d)\n",
-+ mmc_hostname(host->mmc), host->clock,
-+ host->src_clks[idx], host->cdiv,
-+ host->mmc->actual_clock);
-+}
-+
- void bcm2835_sdhost_set_clock(struct bcm2835_host *host)
- {
- int div = 0; /* Initialized for compiler warning */
- unsigned int clock = host->clock;
-+ int clk_idx;
-
- if (host->debug)
- pr_info("%s: set_clock(%d)\n", mmc_hostname(host->mmc), clock);
-@@ -1553,53 +1581,45 @@ void bcm2835_sdhost_set_clock(struct bcm
- return;
- }
-
-- div = host->cur_clk / clock;
-- if (div < 2)
-- div = 2;
-- if ((host->cur_clk / div) > clock)
-- div++;
-- div -= 2;
--
-- if (div > SDCDIV_MAX_CDIV)
-- div = SDCDIV_MAX_CDIV;
--
-- clock = host->cur_clk / (div + 2);
-- host->mmc->actual_clock = clock;
--
-- /* Calibrate some delays */
--
-- host->ns_per_fifo_word = (1000000000/clock) *
-- ((host->mmc->caps & MMC_CAP_4_BIT_DATA) ? 8 : 32);
-+ /* Calculate the clock divisors */
-+ for (clk_idx = 0; clk_idx <= host->variable_clock; clk_idx++)
-+ {
-+ unsigned int cur_clk = host->src_clks[clk_idx];
-+ unsigned int actual_clock;
-
-- if (clock > host->clock) {
-- /* Save the closest value, to make it easier
-- to reduce in the event of error */
-- host->overclock_50 = (clock/MHZ);
--
-- if (clock != host->overclock) {
-- pr_warn("%s: overclocking to %dHz\n",
-- mmc_hostname(host->mmc), clock);
-- host->overclock = clock;
-+ div = cur_clk / clock;
-+ if (div < 2)
-+ div = 2;
-+ if ((cur_clk / div) > clock)
-+ div++;
-+ div -= 2;
-+
-+ if (div > SDCDIV_MAX_CDIV)
-+ div = SDCDIV_MAX_CDIV;
-+ actual_clock = cur_clk / (div + 2);
-+
-+ host->cdivs[clk_idx] = div;
-+ host->clocks[clk_idx] = actual_clock;
-+
-+ if (host->overclock_50 != host->prev_overclock_50) {
-+ const char *clk_name = "";
-+ if (host->variable_clock)
-+ clk_name = clk_idx ? " (turbo)" : " (normal)";
-+ if (actual_clock > host->clock)
-+ pr_info("%s: overclocking to %dHz%s\n",
-+ mmc_hostname(host->mmc),
-+ actual_clock, clk_name);
-+ else if ((host->overclock_50 < 50) && (clk_idx == 0))
-+ pr_info("%s: cancelling overclock%s\n",
-+ mmc_hostname(host->mmc),
-+ host->variable_clock ? "s" : "");
- }
- }
-- else if (host->overclock)
-- {
-- host->overclock = 0;
-- if (clock == 50 * MHZ)
-- pr_warn("%s: cancelling overclock\n",
-- mmc_hostname(host->mmc));
-- }
-
-- host->cdiv = div;
-- bcm2835_sdhost_write(host, host->cdiv, SDCDIV);
-+ if (host->clock == 50*MHZ)
-+ host->prev_overclock_50 = host->overclock_50;
-
-- /* Set the timeout to 500ms */
-- bcm2835_sdhost_write(host, host->mmc->actual_clock/2, SDTOUT);
--
-- if (host->debug)
-- pr_info("%s: clock=%d -> cur_clk=%d, cdiv=%x (actual clock %d)\n",
-- mmc_hostname(host->mmc), host->clock,
-- host->cur_clk, host->cdiv, host->mmc->actual_clock);
-+ bcm2835_sdhost_select_clock(host, host->cur_clk_idx);
- }
-
- static void bcm2835_sdhost_request(struct mmc_host *mmc, struct mmc_request *mrq)
-@@ -1657,6 +1677,9 @@ static void bcm2835_sdhost_request(struc
-
- spin_lock_irqsave(&host->lock, flags);
-
-+ if (host->next_clk_idx != host->cur_clk_idx)
-+ bcm2835_sdhost_select_clock(host, host->next_clk_idx);
-+
- WARN_ON(host->mrq != NULL);
- host->mrq = mrq;
-
-@@ -1719,11 +1742,7 @@ static int bcm2835_sdhost_cpufreq_callba
- return NOTIFY_BAD;
- break;
- case CPUFREQ_POSTCHANGE:
-- if (freq->new > freq->old)
-- host->cur_clk = host->max_clk;
-- else
-- host->cur_clk = host->min_clk;
-- bcm2835_sdhost_set_clock(host);
-+ host->next_clk_idx = (freq->new > freq->old);
- up(&host->cpufreq_semaphore);
- break;
- default:
-@@ -1763,8 +1782,11 @@ static void bcm2835_sdhost_set_ios(struc
- ios->clock, ios->power_mode, ios->bus_width,
- ios->timing, ios->signal_voltage, ios->drv_type);
-
-- if (ios->clock && !host->cur_clk)
-- host->cur_clk = get_core_clock(RPI_FIRMWARE_GET_CLOCK_RATE);
-+ if (ios->clock && (host->cur_clk_idx == -1)) {
-+ unsigned int cur_clk =
-+ get_core_clock(RPI_FIRMWARE_GET_CLOCK_RATE);
-+ host->cur_clk_idx = (cur_clk == host->src_clks[0]) ? 0 : 1;
-+ }
-
- spin_lock_irqsave(&host->lock, flags);
-
-@@ -1854,11 +1876,12 @@ static void bcm2835_sdhost_tasklet_finis
-
- /* Drop the overclock after any data corruption, or after any
- error overclocked */
-- if (host->overclock) {
-+ if (host->clock > 50*MHZ) {
- if ((mrq->cmd && mrq->cmd->error) ||
- (mrq->data && mrq->data->error) ||
- (mrq->stop && mrq->stop->error)) {
-- host->overclock_50--;
-+ host->overclock_50 = (host->clock/MHZ) - 1;
-+
- pr_warn("%s: reducing overclock due to errors\n",
- mmc_hostname(host->mmc));
- bcm2835_sdhost_set_clock(host);
-@@ -2022,7 +2045,7 @@ static int bcm2835_sdhost_probe(struct p
- struct bcm2835_host *host;
- struct mmc_host *mmc;
- const __be32 *addr;
-- unsigned int max_clk;
-+ unsigned int max_clk, min_clk;
- int ret;
-
- pr_debug("bcm2835_sdhost_probe\n");
-@@ -2128,12 +2151,8 @@ static int bcm2835_sdhost_probe(struct p
- else
- mmc->caps |= MMC_CAP_4_BIT_DATA;
-
-- ret = bcm2835_sdhost_add_host(host);
-- if (ret)
-- goto err;
--
- /* Query the core clock frequencies */
-- host->min_clk = get_core_clock(RPI_FIRMWARE_GET_MIN_CLOCK_RATE);
-+ min_clk = get_core_clock(RPI_FIRMWARE_GET_MIN_CLOCK_RATE);
- max_clk = get_core_clock(RPI_FIRMWARE_GET_MAX_CLOCK_RATE);
- if (max_clk != host->max_clk) {
- pr_warn("%s: Expected max clock %d, found %d\n",
-@@ -2141,19 +2160,24 @@ static int bcm2835_sdhost_probe(struct p
- host->max_clk = max_clk;
- }
-
-- if (host->min_clk != host->max_clk) {
-+ host->src_clks[0] = min_clk;
-+ host->cur_clk_idx = -1;
-+ if (max_clk != min_clk) {
-+ host->src_clks[1] = max_clk;
- host->cpufreq_nb.notifier_call =
- bcm2835_sdhost_cpufreq_callback;
- sema_init(&host->cpufreq_semaphore, 1);
- cpufreq_register_notifier(&host->cpufreq_nb,
- CPUFREQ_TRANSITION_NOTIFIER);
- host->variable_clock = 1;
-- host->cur_clk = 0; /* Get this later */
- } else {
- host->variable_clock = 0;
-- host->cur_clk = host->max_clk;
- }
-
-+ ret = bcm2835_sdhost_add_host(host);
-+ if (ret)
-+ goto err;
-+
- platform_set_drvdata(pdev, host);
-
- pr_debug("bcm2835_sdhost_probe -> OK\n");
diff --git a/target/linux/brcm2708/patches-4.4/0223-Revert-bcm2835-sdhost-Precalc-divisors-and-overclock.patch b/target/linux/brcm2708/patches-4.4/0223-Revert-bcm2835-sdhost-Precalc-divisors-and-overclock.patch
deleted file mode 100644
index daa935f..0000000
--- a/target/linux/brcm2708/patches-4.4/0223-Revert-bcm2835-sdhost-Precalc-divisors-and-overclock.patch
+++ /dev/null
@@ -1,266 +0,0 @@
-From d1d692081ec333f981b892cac660ac73977923d2 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 4 Apr 2016 12:35:32 +0100
-Subject: [PATCH] Revert "bcm2835-sdhost: Precalc divisors and overclocks"
-
-This reverts commit 20260462773366a5734e5268dae0a4c179a21a2d.
----
- drivers/mmc/host/bcm2835-sdhost.c | 152 ++++++++++++++++----------------------
- 1 file changed, 64 insertions(+), 88 deletions(-)
-
---- a/drivers/mmc/host/bcm2835-sdhost.c
-+++ b/drivers/mmc/host/bcm2835-sdhost.c
-@@ -154,15 +154,12 @@ struct bcm2835_host {
- u32 pio_timeout; /* In jiffies */
-
- int clock; /* Current clock speed */
-- int clocks[2];
-
- bool slow_card; /* Force 11-bit divisor */
-
- unsigned int max_clk; /* Max src clock freq */
-- unsigned int src_clks[2]; /* Min/max src clock freqs */
-- unsigned int cur_clk_idx; /* Index of current clock */
-- unsigned int next_clk_idx; /* Next clock index */
-- unsigned int cdivs[2];
-+ unsigned int min_clk; /* Min src clock freq */
-+ unsigned int cur_clk; /* Current src clock freq */
-
- struct tasklet_struct finish_tasklet; /* Tasklet structures */
-
-@@ -216,7 +213,7 @@ struct bcm2835_host {
- u32 delay_after_stop; /* minimum time between stop and subsequent data transfer */
- u32 delay_after_this_stop; /* minimum time between this stop and subsequent data transfer */
- u32 overclock_50; /* frequency to use when 50MHz is requested (in MHz) */
-- u32 prev_overclock_50;
-+ u32 overclock; /* Current frequency if overclocked, else zero */
- u32 pio_limit; /* Maximum block count for PIO (0 = always DMA) */
-
- u32 sectors; /* Cached card size in sectors */
-@@ -1512,35 +1509,10 @@ static irqreturn_t bcm2835_sdhost_irq(in
- return result;
- }
-
--static void bcm2835_sdhost_select_clock(struct bcm2835_host *host, int idx)
--{
-- unsigned int clock = host->clocks[idx];
-- unsigned int cdiv = host->cdivs[idx];
--
-- host->mmc->actual_clock = clock;
-- host->ns_per_fifo_word = (1000000000/clock) *
-- ((host->mmc->caps & MMC_CAP_4_BIT_DATA) ? 8 : 32);
--
-- host->cdiv = cdiv;
-- bcm2835_sdhost_write(host, host->cdiv, SDCDIV);
--
-- /* Set the timeout to 500ms */
-- bcm2835_sdhost_write(host, clock/2, SDTOUT);
--
-- host->cur_clk_idx = host->next_clk_idx = idx;
--
-- if (host->debug)
-- pr_info("%s: clock=%d -> src_clk=%d, cdiv=%x (actual %d)\n",
-- mmc_hostname(host->mmc), host->clock,
-- host->src_clks[idx], host->cdiv,
-- host->mmc->actual_clock);
--}
--
- void bcm2835_sdhost_set_clock(struct bcm2835_host *host)
- {
- int div = 0; /* Initialized for compiler warning */
- unsigned int clock = host->clock;
-- int clk_idx;
-
- if (host->debug)
- pr_info("%s: set_clock(%d)\n", mmc_hostname(host->mmc), clock);
-@@ -1581,45 +1553,53 @@ void bcm2835_sdhost_set_clock(struct bcm
- return;
- }
-
-- /* Calculate the clock divisors */
-- for (clk_idx = 0; clk_idx <= host->variable_clock; clk_idx++)
-- {
-- unsigned int cur_clk = host->src_clks[clk_idx];
-- unsigned int actual_clock;
-+ div = host->cur_clk / clock;
-+ if (div < 2)
-+ div = 2;
-+ if ((host->cur_clk / div) > clock)
-+ div++;
-+ div -= 2;
-+
-+ if (div > SDCDIV_MAX_CDIV)
-+ div = SDCDIV_MAX_CDIV;
-+
-+ clock = host->cur_clk / (div + 2);
-+ host->mmc->actual_clock = clock;
-+
-+ /* Calibrate some delays */
-+
-+ host->ns_per_fifo_word = (1000000000/clock) *
-+ ((host->mmc->caps & MMC_CAP_4_BIT_DATA) ? 8 : 32);
-
-- div = cur_clk / clock;
-- if (div < 2)
-- div = 2;
-- if ((cur_clk / div) > clock)
-- div++;
-- div -= 2;
--
-- if (div > SDCDIV_MAX_CDIV)
-- div = SDCDIV_MAX_CDIV;
-- actual_clock = cur_clk / (div + 2);
--
-- host->cdivs[clk_idx] = div;
-- host->clocks[clk_idx] = actual_clock;
--
-- if (host->overclock_50 != host->prev_overclock_50) {
-- const char *clk_name = "";
-- if (host->variable_clock)
-- clk_name = clk_idx ? " (turbo)" : " (normal)";
-- if (actual_clock > host->clock)
-- pr_info("%s: overclocking to %dHz%s\n",
-- mmc_hostname(host->mmc),
-- actual_clock, clk_name);
-- else if ((host->overclock_50 < 50) && (clk_idx == 0))
-- pr_info("%s: cancelling overclock%s\n",
-- mmc_hostname(host->mmc),
-- host->variable_clock ? "s" : "");
-+ if (clock > host->clock) {
-+ /* Save the closest value, to make it easier
-+ to reduce in the event of error */
-+ host->overclock_50 = (clock/MHZ);
-+
-+ if (clock != host->overclock) {
-+ pr_warn("%s: overclocking to %dHz\n",
-+ mmc_hostname(host->mmc), clock);
-+ host->overclock = clock;
- }
- }
-+ else if (host->overclock)
-+ {
-+ host->overclock = 0;
-+ if (clock == 50 * MHZ)
-+ pr_warn("%s: cancelling overclock\n",
-+ mmc_hostname(host->mmc));
-+ }
-
-- if (host->clock == 50*MHZ)
-- host->prev_overclock_50 = host->overclock_50;
-+ host->cdiv = div;
-+ bcm2835_sdhost_write(host, host->cdiv, SDCDIV);
-
-- bcm2835_sdhost_select_clock(host, host->cur_clk_idx);
-+ /* Set the timeout to 500ms */
-+ bcm2835_sdhost_write(host, host->mmc->actual_clock/2, SDTOUT);
-+
-+ if (host->debug)
-+ pr_info("%s: clock=%d -> cur_clk=%d, cdiv=%x (actual clock %d)\n",
-+ mmc_hostname(host->mmc), host->clock,
-+ host->cur_clk, host->cdiv, host->mmc->actual_clock);
- }
-
- static void bcm2835_sdhost_request(struct mmc_host *mmc, struct mmc_request *mrq)
-@@ -1677,9 +1657,6 @@ static void bcm2835_sdhost_request(struc
-
- spin_lock_irqsave(&host->lock, flags);
-
-- if (host->next_clk_idx != host->cur_clk_idx)
-- bcm2835_sdhost_select_clock(host, host->next_clk_idx);
--
- WARN_ON(host->mrq != NULL);
- host->mrq = mrq;
-
-@@ -1742,7 +1719,11 @@ static int bcm2835_sdhost_cpufreq_callba
- return NOTIFY_BAD;
- break;
- case CPUFREQ_POSTCHANGE:
-- host->next_clk_idx = (freq->new > freq->old);
-+ if (freq->new > freq->old)
-+ host->cur_clk = host->max_clk;
-+ else
-+ host->cur_clk = host->min_clk;
-+ bcm2835_sdhost_set_clock(host);
- up(&host->cpufreq_semaphore);
- break;
- default:
-@@ -1782,11 +1763,8 @@ static void bcm2835_sdhost_set_ios(struc
- ios->clock, ios->power_mode, ios->bus_width,
- ios->timing, ios->signal_voltage, ios->drv_type);
-
-- if (ios->clock && (host->cur_clk_idx == -1)) {
-- unsigned int cur_clk =
-- get_core_clock(RPI_FIRMWARE_GET_CLOCK_RATE);
-- host->cur_clk_idx = (cur_clk == host->src_clks[0]) ? 0 : 1;
-- }
-+ if (ios->clock && !host->cur_clk)
-+ host->cur_clk = get_core_clock(RPI_FIRMWARE_GET_CLOCK_RATE);
-
- spin_lock_irqsave(&host->lock, flags);
-
-@@ -1876,12 +1854,11 @@ static void bcm2835_sdhost_tasklet_finis
-
- /* Drop the overclock after any data corruption, or after any
- error overclocked */
-- if (host->clock > 50*MHZ) {
-+ if (host->overclock) {
- if ((mrq->cmd && mrq->cmd->error) ||
- (mrq->data && mrq->data->error) ||
- (mrq->stop && mrq->stop->error)) {
-- host->overclock_50 = (host->clock/MHZ) - 1;
--
-+ host->overclock_50--;
- pr_warn("%s: reducing overclock due to errors\n",
- mmc_hostname(host->mmc));
- bcm2835_sdhost_set_clock(host);
-@@ -2045,7 +2022,7 @@ static int bcm2835_sdhost_probe(struct p
- struct bcm2835_host *host;
- struct mmc_host *mmc;
- const __be32 *addr;
-- unsigned int max_clk, min_clk;
-+ unsigned int max_clk;
- int ret;
-
- pr_debug("bcm2835_sdhost_probe\n");
-@@ -2151,8 +2128,12 @@ static int bcm2835_sdhost_probe(struct p
- else
- mmc->caps |= MMC_CAP_4_BIT_DATA;
-
-+ ret = bcm2835_sdhost_add_host(host);
-+ if (ret)
-+ goto err;
-+
- /* Query the core clock frequencies */
-- min_clk = get_core_clock(RPI_FIRMWARE_GET_MIN_CLOCK_RATE);
-+ host->min_clk = get_core_clock(RPI_FIRMWARE_GET_MIN_CLOCK_RATE);
- max_clk = get_core_clock(RPI_FIRMWARE_GET_MAX_CLOCK_RATE);
- if (max_clk != host->max_clk) {
- pr_warn("%s: Expected max clock %d, found %d\n",
-@@ -2160,24 +2141,19 @@ static int bcm2835_sdhost_probe(struct p
- host->max_clk = max_clk;
- }
-
-- host->src_clks[0] = min_clk;
-- host->cur_clk_idx = -1;
-- if (max_clk != min_clk) {
-- host->src_clks[1] = max_clk;
-+ if (host->min_clk != host->max_clk) {
- host->cpufreq_nb.notifier_call =
- bcm2835_sdhost_cpufreq_callback;
- sema_init(&host->cpufreq_semaphore, 1);
- cpufreq_register_notifier(&host->cpufreq_nb,
- CPUFREQ_TRANSITION_NOTIFIER);
- host->variable_clock = 1;
-+ host->cur_clk = 0; /* Get this later */
- } else {
- host->variable_clock = 0;
-+ host->cur_clk = host->max_clk;
- }
-
-- ret = bcm2835_sdhost_add_host(host);
-- if (ret)
-- goto err;
--
- platform_set_drvdata(pdev, host);
-
- pr_debug("bcm2835_sdhost_probe -> OK\n");
diff --git a/target/linux/brcm2708/patches-4.4/0224-Revert-bcm2835-sdhost-Adjust-to-core-clock-changes.patch b/target/linux/brcm2708/patches-4.4/0224-Revert-bcm2835-sdhost-Adjust-to-core-clock-changes.patch
deleted file mode 100644
index 5469934..0000000
--- a/target/linux/brcm2708/patches-4.4/0224-Revert-bcm2835-sdhost-Adjust-to-core-clock-changes.patch
+++ /dev/null
@@ -1,327 +0,0 @@
-From a48331cf3aaa92e7290e8876b13bd1efd64541e6 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 4 Apr 2016 12:35:51 +0100
-Subject: [PATCH] Revert "bcm2835-sdhost: Adjust to core clock changes"
-
-This reverts commit 4b89d07fd299a0f4e25321920cb74416ba2e638e.
----
- drivers/mmc/host/Kconfig | 1 -
- drivers/mmc/host/bcm2835-sdhost.c | 140 ++++++--------------------------------
- 2 files changed, 22 insertions(+), 119 deletions(-)
-
---- a/drivers/mmc/host/Kconfig
-+++ b/drivers/mmc/host/Kconfig
-@@ -36,7 +36,6 @@ config MMC_BCM2835_PIO_DMA_BARRIER
- config MMC_BCM2835_SDHOST
- tristate "Support for the SDHost controller on BCM2708/9"
- depends on MACH_BCM2708 || MACH_BCM2709 || ARCH_BCM2835
-- depends on RASPBERRYPI_FIRMWARE
- help
- This selects the SDHost controller on BCM2835/6.
-
---- a/drivers/mmc/host/bcm2835-sdhost.c
-+++ b/drivers/mmc/host/bcm2835-sdhost.c
-@@ -50,10 +50,6 @@
- #include <linux/of_dma.h>
- #include <linux/time.h>
- #include <linux/workqueue.h>
--#include <linux/cpufreq.h>
--#include <linux/semaphore.h>
--#include <soc/bcm2835/raspberrypi-firmware.h>
--
-
- #define DRIVER_NAME "sdhost-bcm2835"
-
-@@ -140,8 +136,6 @@
-
- #define MHZ 1000000
-
--#define RPI_FIRMWARE_CLOCK_CORE 4
--
-
- struct bcm2835_host {
- spinlock_t lock;
-@@ -157,9 +151,7 @@ struct bcm2835_host {
-
- bool slow_card; /* Force 11-bit divisor */
-
-- unsigned int max_clk; /* Max src clock freq */
-- unsigned int min_clk; /* Min src clock freq */
-- unsigned int cur_clk; /* Current src clock freq */
-+ unsigned int max_clk; /* Max possible freq */
-
- struct tasklet_struct finish_tasklet; /* Tasklet structures */
-
-@@ -191,7 +183,6 @@ struct bcm2835_host {
- unsigned int use_sbc:1; /* Send CMD23 */
-
- unsigned int debug:1; /* Enable debug output */
-- unsigned int variable_clock:1; /* The core clock may change */
-
- /*DMA part*/
- struct dma_chan *dma_chan_rxtx; /* DMA channel for reads and writes */
-@@ -217,9 +208,6 @@ struct bcm2835_host {
- u32 pio_limit; /* Maximum block count for PIO (0 = always DMA) */
-
- u32 sectors; /* Cached card size in sectors */
--
-- struct notifier_block cpufreq_nb; /* The cpufreq callback list item */
-- struct semaphore cpufreq_semaphore; /* Interlock between SD activity and cpufreq changes */
- };
-
- #if ENABLE_LOG
-@@ -239,10 +227,6 @@ static u32 sdhost_log_idx;
- static spinlock_t log_lock;
- static void __iomem *timer_base;
-
--static int bcm2835_sdhost_cpufreq_callback(struct notifier_block *nb,
-- unsigned long action, void *data);
--static unsigned int get_core_clock(unsigned int mode);
--
- #define LOG_ENTRIES (256*1)
- #define LOG_SIZE (sizeof(LOG_ENTRY_T)*LOG_ENTRIES)
-
-@@ -464,14 +448,20 @@ static void bcm2835_sdhost_reset(struct
-
- static void bcm2835_sdhost_set_ios(struct mmc_host *mmc, struct mmc_ios *ios);
-
--static void bcm2835_sdhost_init(struct bcm2835_host *host)
-+static void bcm2835_sdhost_init(struct bcm2835_host *host, int soft)
- {
-- pr_debug("bcm2835_sdhost_init()\n");
-+ pr_debug("bcm2835_sdhost_init(%d)\n", soft);
-
- /* Set interrupt enables */
- host->hcfg = SDHCFG_BUSY_IRPT_EN;
-
- bcm2835_sdhost_reset_internal(host);
-+
-+ if (soft) {
-+ /* force clock reconfiguration */
-+ host->clock = 0;
-+ bcm2835_sdhost_set_ios(host->mmc, &host->mmc->ios);
-+ }
- }
-
- static void bcm2835_sdhost_wait_transfer_complete(struct bcm2835_host *host)
-@@ -1509,10 +1499,10 @@ static irqreturn_t bcm2835_sdhost_irq(in
- return result;
- }
-
--void bcm2835_sdhost_set_clock(struct bcm2835_host *host)
-+void bcm2835_sdhost_set_clock(struct bcm2835_host *host, unsigned int clock)
- {
- int div = 0; /* Initialized for compiler warning */
-- unsigned int clock = host->clock;
-+ unsigned int input_clock = clock;
-
- if (host->debug)
- pr_info("%s: set_clock(%d)\n", mmc_hostname(host->mmc), clock);
-@@ -1553,17 +1543,17 @@ void bcm2835_sdhost_set_clock(struct bcm
- return;
- }
-
-- div = host->cur_clk / clock;
-+ div = host->max_clk / clock;
- if (div < 2)
- div = 2;
-- if ((host->cur_clk / div) > clock)
-+ if ((host->max_clk / div) > clock)
- div++;
- div -= 2;
-
- if (div > SDCDIV_MAX_CDIV)
- div = SDCDIV_MAX_CDIV;
-
-- clock = host->cur_clk / (div + 2);
-+ clock = host->max_clk / (div + 2);
- host->mmc->actual_clock = clock;
-
- /* Calibrate some delays */
-@@ -1571,7 +1561,7 @@ void bcm2835_sdhost_set_clock(struct bcm
- host->ns_per_fifo_word = (1000000000/clock) *
- ((host->mmc->caps & MMC_CAP_4_BIT_DATA) ? 8 : 32);
-
-- if (clock > host->clock) {
-+ if (clock > input_clock) {
- /* Save the closest value, to make it easier
- to reduce in the event of error */
- host->overclock_50 = (clock/MHZ);
-@@ -1597,9 +1587,9 @@ void bcm2835_sdhost_set_clock(struct bcm
- bcm2835_sdhost_write(host, host->mmc->actual_clock/2, SDTOUT);
-
- if (host->debug)
-- pr_info("%s: clock=%d -> cur_clk=%d, cdiv=%x (actual clock %d)\n",
-- mmc_hostname(host->mmc), host->clock,
-- host->cur_clk, host->cdiv, host->mmc->actual_clock);
-+ pr_info("%s: clock=%d -> max_clk=%d, cdiv=%x (actual clock %d)\n",
-+ mmc_hostname(host->mmc), input_clock,
-+ host->max_clk, host->cdiv, host->mmc->actual_clock);
- }
-
- static void bcm2835_sdhost_request(struct mmc_host *mmc, struct mmc_request *mrq)
-@@ -1648,13 +1638,6 @@ static void bcm2835_sdhost_request(struc
- (mrq->data->blocks > host->pio_limit))
- bcm2835_sdhost_prepare_dma(host, mrq->data);
-
-- if (host->variable_clock &&
-- (down_killable(&host->cpufreq_semaphore) != 0)) {
-- mrq->cmd->error = -EINTR;
-- mmc_request_done(mmc, mrq);
-- return;
-- }
--
- spin_lock_irqsave(&host->lock, flags);
-
- WARN_ON(host->mrq != NULL);
-@@ -1704,52 +1687,6 @@ static void bcm2835_sdhost_request(struc
- spin_unlock_irqrestore(&host->lock, flags);
- }
-
--static int bcm2835_sdhost_cpufreq_callback(struct notifier_block *nb,
-- unsigned long action, void *data)
--{
-- struct cpufreq_freqs *freq = data;
-- struct bcm2835_host *host;
--
-- host = container_of(nb, struct bcm2835_host, cpufreq_nb);
--
-- if (freq->cpu == 0) {
-- switch (action) {
-- case CPUFREQ_PRECHANGE:
-- if (down_killable(&host->cpufreq_semaphore) != 0)
-- return NOTIFY_BAD;
-- break;
-- case CPUFREQ_POSTCHANGE:
-- if (freq->new > freq->old)
-- host->cur_clk = host->max_clk;
-- else
-- host->cur_clk = host->min_clk;
-- bcm2835_sdhost_set_clock(host);
-- up(&host->cpufreq_semaphore);
-- break;
-- default:
-- break;
-- }
-- }
-- return NOTIFY_OK;
--}
--
--static unsigned int get_core_clock(unsigned int mode)
--{
-- struct rpi_firmware *fw = rpi_firmware_get(NULL);
-- struct {
-- u32 id;
-- u32 val;
-- } packet;
-- int ret;
--
-- packet.id = RPI_FIRMWARE_CLOCK_CORE;
-- ret = rpi_firmware_property(fw, mode, &packet, sizeof(packet));
-- if (ret)
-- return 0;
--
-- return packet.val;
--}
--
- static void bcm2835_sdhost_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
- {
-
-@@ -1763,16 +1700,13 @@ static void bcm2835_sdhost_set_ios(struc
- ios->clock, ios->power_mode, ios->bus_width,
- ios->timing, ios->signal_voltage, ios->drv_type);
-
-- if (ios->clock && !host->cur_clk)
-- host->cur_clk = get_core_clock(RPI_FIRMWARE_GET_CLOCK_RATE);
--
- spin_lock_irqsave(&host->lock, flags);
-
- log_event("IOS<", ios->clock, 0);
-
- if (!ios->clock || ios->clock != host->clock) {
-+ bcm2835_sdhost_set_clock(host, ios->clock);
- host->clock = ios->clock;
-- bcm2835_sdhost_set_clock(host);
- }
-
- /* set bus width */
-@@ -1861,7 +1795,7 @@ static void bcm2835_sdhost_tasklet_finis
- host->overclock_50--;
- pr_warn("%s: reducing overclock due to errors\n",
- mmc_hostname(host->mmc));
-- bcm2835_sdhost_set_clock(host);
-+ bcm2835_sdhost_set_clock(host,50*MHZ);
- mrq->cmd->error = -EILSEQ;
- mrq->cmd->retries = 1;
- }
-@@ -1879,9 +1813,6 @@ static void bcm2835_sdhost_tasklet_finis
-
- spin_unlock_irqrestore(&host->lock, flags);
-
-- if (host->variable_clock)
-- up(&host->cpufreq_semaphore);
--
- if (terminate_chan)
- {
- int err = dmaengine_terminate_all(terminate_chan);
-@@ -1984,10 +1915,10 @@ int bcm2835_sdhost_add_host(struct bcm28
- setup_timer(&host->timer, bcm2835_sdhost_timeout,
- (unsigned long)host);
-
-- bcm2835_sdhost_init(host);
-+ bcm2835_sdhost_init(host, 0);
-
- ret = request_irq(host->irq, bcm2835_sdhost_irq, 0 /*IRQF_SHARED*/,
-- mmc_hostname(mmc), host);
-+ mmc_hostname(mmc), host);
- if (ret) {
- pr_err("%s: failed to request IRQ %d: %d\n",
- mmc_hostname(mmc), host->irq, ret);
-@@ -2022,7 +1953,6 @@ static int bcm2835_sdhost_probe(struct p
- struct bcm2835_host *host;
- struct mmc_host *mmc;
- const __be32 *addr;
-- unsigned int max_clk;
- int ret;
-
- pr_debug("bcm2835_sdhost_probe\n");
-@@ -2132,28 +2062,6 @@ static int bcm2835_sdhost_probe(struct p
- if (ret)
- goto err;
-
-- /* Query the core clock frequencies */
-- host->min_clk = get_core_clock(RPI_FIRMWARE_GET_MIN_CLOCK_RATE);
-- max_clk = get_core_clock(RPI_FIRMWARE_GET_MAX_CLOCK_RATE);
-- if (max_clk != host->max_clk) {
-- pr_warn("%s: Expected max clock %d, found %d\n",
-- mmc_hostname(mmc), host->max_clk, max_clk);
-- host->max_clk = max_clk;
-- }
--
-- if (host->min_clk != host->max_clk) {
-- host->cpufreq_nb.notifier_call =
-- bcm2835_sdhost_cpufreq_callback;
-- sema_init(&host->cpufreq_semaphore, 1);
-- cpufreq_register_notifier(&host->cpufreq_nb,
-- CPUFREQ_TRANSITION_NOTIFIER);
-- host->variable_clock = 1;
-- host->cur_clk = 0; /* Get this later */
-- } else {
-- host->variable_clock = 0;
-- host->cur_clk = host->max_clk;
-- }
--
- platform_set_drvdata(pdev, host);
-
- pr_debug("bcm2835_sdhost_probe -> OK\n");
-@@ -2173,10 +2081,6 @@ static int bcm2835_sdhost_remove(struct
-
- pr_debug("bcm2835_sdhost_remove\n");
-
-- if (host->variable_clock)
-- cpufreq_unregister_notifier(&host->cpufreq_nb,
-- CPUFREQ_TRANSITION_NOTIFIER);
--
- mmc_remove_host(host->mmc);
-
- bcm2835_sdhost_set_power(host, false);
diff --git a/target/linux/brcm2708/patches-4.4/0225-bcm2835-sdhost-Firmware-manages-the-clock-divisor.patch b/target/linux/brcm2708/patches-4.4/0225-bcm2835-sdhost-Firmware-manages-the-clock-divisor.patch
deleted file mode 100644
index 0f28064..0000000
--- a/target/linux/brcm2708/patches-4.4/0225-bcm2835-sdhost-Firmware-manages-the-clock-divisor.patch
+++ /dev/null
@@ -1,226 +0,0 @@
-From 2fd8e8397c3ae6e50fdb8b5224a195678cad9ed6 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 4 Apr 2016 16:03:18 +0100
-Subject: [PATCH] bcm2835-sdhost: Firmware manages the clock divisor
-
-The bcm2835-sdhost driver hands control of the CDIV clock divisor
-register to matching firmware, allowing it to adjust to a changing
-core clock. This removes the need to use the performance governor or
-to enable io_is_busy on the on-demand governor in order to get the
-best SD performance.
-
-N.B. As SD clocks must be an integer divisor of the core clock, it is
-possible that the SD clock for "turbo" mode can be different (even
-lower) than "normal" mode.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- drivers/mmc/host/bcm2835-sdhost.c | 120 ++++++++++++++++++-----------
- include/soc/bcm2835/raspberrypi-firmware.h | 1 +
- 2 files changed, 74 insertions(+), 47 deletions(-)
-
---- a/drivers/mmc/host/bcm2835-sdhost.c
-+++ b/drivers/mmc/host/bcm2835-sdhost.c
-@@ -50,6 +50,7 @@
- #include <linux/of_dma.h>
- #include <linux/time.h>
- #include <linux/workqueue.h>
-+#include <soc/bcm2835/raspberrypi-firmware.h>
-
- #define DRIVER_NAME "sdhost-bcm2835"
-
-@@ -183,6 +184,7 @@ struct bcm2835_host {
- unsigned int use_sbc:1; /* Send CMD23 */
-
- unsigned int debug:1; /* Enable debug output */
-+ unsigned int firmware_sets_cdiv:1; /* Let the firmware manage the clock */
-
- /*DMA part*/
- struct dma_chan *dma_chan_rxtx; /* DMA channel for reads and writes */
-@@ -430,7 +432,7 @@ static void bcm2835_sdhost_reset_interna
- host->clock = 0;
- host->sectors = 0;
- bcm2835_sdhost_write(host, host->hcfg, SDHCFG);
-- bcm2835_sdhost_write(host, host->cdiv, SDCDIV);
-+ bcm2835_sdhost_write(host, SDCDIV_MAX_CDIV, SDCDIV);
- mmiowb();
- }
-
-@@ -1534,62 +1536,75 @@ void bcm2835_sdhost_set_clock(struct bcm
-
- host->mmc->actual_clock = 0;
-
-- if (clock < 100000) {
-- /* Can't stop the clock, but make it as slow as possible
-- * to show willing
-- */
-- host->cdiv = SDCDIV_MAX_CDIV;
-- bcm2835_sdhost_write(host, host->cdiv, SDCDIV);
-- return;
-- }
--
-- div = host->max_clk / clock;
-- if (div < 2)
-- div = 2;
-- if ((host->max_clk / div) > clock)
-- div++;
-- div -= 2;
-+ if (host->firmware_sets_cdiv) {
-+ u32 msg[3] = { clock, 0, 0 };
-
-- if (div > SDCDIV_MAX_CDIV)
-- div = SDCDIV_MAX_CDIV;
-+ rpi_firmware_property(rpi_firmware_get(NULL),
-+ RPI_FIRMWARE_SET_SDHOST_CLOCK,
-+ &msg, sizeof(msg));
-
-- clock = host->max_clk / (div + 2);
-- host->mmc->actual_clock = clock;
-+ clock = max(msg[1], msg[2]);
-+ } else {
-+ if (clock < 100000) {
-+ /* Can't stop the clock, but make it as slow as
-+ * possible to show willing
-+ */
-+ host->cdiv = SDCDIV_MAX_CDIV;
-+ bcm2835_sdhost_write(host, host->cdiv, SDCDIV);
-+ return;
-+ }
-+
-+ div = host->max_clk / clock;
-+ if (div < 2)
-+ div = 2;
-+ if ((host->max_clk / div) > clock)
-+ div++;
-+ div -= 2;
-+
-+ if (div > SDCDIV_MAX_CDIV)
-+ div = SDCDIV_MAX_CDIV;
-+
-+ clock = host->max_clk / (div + 2);
-+
-+ host->cdiv = div;
-+ bcm2835_sdhost_write(host, host->cdiv, SDCDIV);
-+
-+ if (host->debug)
-+ pr_info("%s: clock=%d -> max_clk=%d, cdiv=%x "
-+ "(actual clock %d)\n",
-+ mmc_hostname(host->mmc), input_clock,
-+ host->max_clk, host->cdiv,
-+ clock);
-+ }
-
- /* Calibrate some delays */
-
- host->ns_per_fifo_word = (1000000000/clock) *
- ((host->mmc->caps & MMC_CAP_4_BIT_DATA) ? 8 : 32);
-
-- if (clock > input_clock) {
-- /* Save the closest value, to make it easier
-- to reduce in the event of error */
-- host->overclock_50 = (clock/MHZ);
--
-- if (clock != host->overclock) {
-- pr_warn("%s: overclocking to %dHz\n",
-- mmc_hostname(host->mmc), clock);
-- host->overclock = clock;
-+ if (input_clock == 50 * MHZ) {
-+ if (clock > input_clock) {
-+ /* Save the closest value, to make it easier
-+ to reduce in the event of error */
-+ host->overclock_50 = (clock/MHZ);
-+
-+ if (clock != host->overclock) {
-+ pr_warn("%s: overclocking to %dHz\n",
-+ mmc_hostname(host->mmc), clock);
-+ host->overclock = clock;
-+ }
-+ } else if (host->overclock) {
-+ host->overclock = 0;
-+ if (clock == 50 * MHZ)
-+ pr_warn("%s: cancelling overclock\n",
-+ mmc_hostname(host->mmc));
- }
- }
-- else if (host->overclock)
-- {
-- host->overclock = 0;
-- if (clock == 50 * MHZ)
-- pr_warn("%s: cancelling overclock\n",
-- mmc_hostname(host->mmc));
-- }
--
-- host->cdiv = div;
-- bcm2835_sdhost_write(host, host->cdiv, SDCDIV);
-
- /* Set the timeout to 500ms */
-- bcm2835_sdhost_write(host, host->mmc->actual_clock/2, SDTOUT);
-+ bcm2835_sdhost_write(host, clock/2, SDTOUT);
-
-- if (host->debug)
-- pr_info("%s: clock=%d -> max_clk=%d, cdiv=%x (actual clock %d)\n",
-- mmc_hostname(host->mmc), input_clock,
-- host->max_clk, host->cdiv, host->mmc->actual_clock);
-+ host->mmc->actual_clock = clock;
- }
-
- static void bcm2835_sdhost_request(struct mmc_host *mmc, struct mmc_request *mrq)
-@@ -1704,11 +1719,6 @@ static void bcm2835_sdhost_set_ios(struc
-
- log_event("IOS<", ios->clock, 0);
-
-- if (!ios->clock || ios->clock != host->clock) {
-- bcm2835_sdhost_set_clock(host, ios->clock);
-- host->clock = ios->clock;
-- }
--
- /* set bus width */
- host->hcfg &= ~SDHCFG_WIDE_EXT_BUS;
- if (ios->bus_width == MMC_BUS_WIDTH_4)
-@@ -1721,6 +1731,11 @@ static void bcm2835_sdhost_set_ios(struc
-
- bcm2835_sdhost_write(host, host->hcfg, SDHCFG);
-
-+ if (!ios->clock || ios->clock != host->clock) {
-+ bcm2835_sdhost_set_clock(host, ios->clock);
-+ host->clock = ios->clock;
-+ }
-+
- mmiowb();
-
- spin_unlock_irqrestore(&host->lock, flags);
-@@ -1953,6 +1968,7 @@ static int bcm2835_sdhost_probe(struct p
- struct bcm2835_host *host;
- struct mmc_host *mmc;
- const __be32 *addr;
-+ u32 msg[3];
- int ret;
-
- pr_debug("bcm2835_sdhost_probe\n");
-@@ -2058,6 +2074,16 @@ static int bcm2835_sdhost_probe(struct p
- else
- mmc->caps |= MMC_CAP_4_BIT_DATA;
-
-+ msg[0] = 0;
-+ msg[1] = ~0;
-+ msg[2] = ~0;
-+
-+ rpi_firmware_property(rpi_firmware_get(NULL),
-+ RPI_FIRMWARE_SET_SDHOST_CLOCK,
-+ &msg, sizeof(msg));
-+
-+ host->firmware_sets_cdiv = (msg[1] != ~0);
-+
- ret = bcm2835_sdhost_add_host(host);
- if (ret)
- goto err;
---- a/include/soc/bcm2835/raspberrypi-firmware.h
-+++ b/include/soc/bcm2835/raspberrypi-firmware.h
-@@ -79,6 +79,7 @@ enum rpi_firmware_property_tag {
- RPI_FIRMWARE_SET_VOLTAGE = 0x00038003,
- RPI_FIRMWARE_SET_TURBO = 0x00038009,
- RPI_FIRMWARE_SET_CUSTOMER_OTP = 0x00038021,
-+ RPI_FIRMWARE_SET_SDHOST_CLOCK = 0x00038042,
-
- /* Dispmanx TAGS */
- RPI_FIRMWARE_FRAMEBUFFER_ALLOCATE = 0x00040001,
diff --git a/target/linux/brcm2708/patches-4.4/0226-Revert-Revert-cpufreq-Temporarily-ignore-io_is_busy-.patch b/target/linux/brcm2708/patches-4.4/0226-Revert-Revert-cpufreq-Temporarily-ignore-io_is_busy-.patch
deleted file mode 100644
index 45308e2..0000000
--- a/target/linux/brcm2708/patches-4.4/0226-Revert-Revert-cpufreq-Temporarily-ignore-io_is_busy-.patch
+++ /dev/null
@@ -1,26 +0,0 @@
-From eaef16fa8bfaf3f2f928315f1005709a3ec9d25c Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Mon, 4 Apr 2016 19:52:27 +0100
-Subject: [PATCH] Revert "Revert "cpufreq: Temporarily ignore io_is_busy=1""
-
-This reverts commit c353af0f83220068c10f6593b1767576b9b6cc18.
----
- drivers/cpufreq/cpufreq_ondemand.c | 7 ++++++-
- 1 file changed, 6 insertions(+), 1 deletion(-)
-
---- a/drivers/cpufreq/cpufreq_ondemand.c
-+++ b/drivers/cpufreq/cpufreq_ondemand.c
-@@ -307,7 +307,12 @@ static ssize_t store_io_is_busy(struct d
- ret = sscanf(buf, "%u", &input);
- if (ret != 1)
- return -EINVAL;
-- od_tuners->io_is_busy = !!input;
-+ // XXX temporary hack
-+ if (input > 1)
-+ input = 1;
-+ else
-+ input = 0;
-+ od_tuners->io_is_busy = input;
-
- /* we need to re-evaluate prev_cpu_idle */
- for_each_online_cpu(j) {
diff --git a/target/linux/brcm2708/patches-4.4/0227-config-Enabled-IPV6_SUBTREES.patch b/target/linux/brcm2708/patches-4.4/0227-config-Enabled-IPV6_SUBTREES.patch
deleted file mode 100644
index 54e5d8b..0000000
--- a/target/linux/brcm2708/patches-4.4/0227-config-Enabled-IPV6_SUBTREES.patch
+++ /dev/null
@@ -1,30 +0,0 @@
-From aa28c8dff61c5663f69a87139364f023766a307c Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Thu, 31 Mar 2016 16:49:52 +0100
-Subject: [PATCH] config: Enabled IPV6_SUBTREES
-
----
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 2 files changed, 2 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -106,6 +106,7 @@ CONFIG_INET6_ESP=m
- CONFIG_INET6_IPCOMP=m
- CONFIG_IPV6_TUNNEL=m
- CONFIG_IPV6_MULTIPLE_TABLES=y
-+CONFIG_IPV6_SUBTREES=y
- CONFIG_IPV6_MROUTE=y
- CONFIG_IPV6_MROUTE_MULTIPLE_TABLES=y
- CONFIG_IPV6_PIMSM_V2=y
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -73,6 +73,7 @@ CONFIG_INET=y
- CONFIG_IP_MULTICAST=y
- CONFIG_IP_ADVANCED_ROUTER=y
- CONFIG_IP_MULTIPLE_TABLES=y
-+CONFIG_IPV6_SUBTREES=y
- CONFIG_IP_ROUTE_MULTIPATH=y
- CONFIG_IP_ROUTE_VERBOSE=y
- CONFIG_IP_PNP=y
diff --git a/target/linux/brcm2708/patches-4.4/0228-add-smsc95xx-packetsize-module_param.patch b/target/linux/brcm2708/patches-4.4/0228-add-smsc95xx-packetsize-module_param.patch
deleted file mode 100644
index f419599..0000000
--- a/target/linux/brcm2708/patches-4.4/0228-add-smsc95xx-packetsize-module_param.patch
+++ /dev/null
@@ -1,42 +0,0 @@
-From c7504685b6f2ee671e1adda42dcfa81dcb3f8c69 Mon Sep 17 00:00:00 2001
-From: Sam Nazarko <email at samnazarko.co.uk>
-Date: Fri, 1 Apr 2016 17:27:21 +0100
-Subject: [PATCH] add smsc95xx packetsize module_param
-
-Signed-off-by: Sam Nazarko <email at samnazarko.co.uk>
----
- drivers/net/usb/smsc95xx.c | 14 +++++++++-----
- 1 file changed, 9 insertions(+), 5 deletions(-)
-
---- a/drivers/net/usb/smsc95xx.c
-+++ b/drivers/net/usb/smsc95xx.c
-@@ -83,6 +83,10 @@ static char *macaddr = ":";
- module_param(macaddr, charp, 0);
- MODULE_PARM_DESC(macaddr, "MAC address");
-
-+static int packetsize = 0;
-+module_param(packetsize, int, 0644);
-+MODULE_PARM_DESC(packetsize, "Override the RX URB packet size");
-+
- static int __must_check __smsc95xx_read_reg(struct usbnet *dev, u32 index,
- u32 *data, int in_pm)
- {
-@@ -1006,13 +1010,13 @@ static int smsc95xx_reset(struct usbnet
-
- if (!turbo_mode) {
- burst_cap = 0;
-- dev->rx_urb_size = MAX_SINGLE_PACKET_SIZE;
-+ dev->rx_urb_size = packetsize ? packetsize : MAX_SINGLE_PACKET_SIZE;
- } else if (dev->udev->speed == USB_SPEED_HIGH) {
-- burst_cap = DEFAULT_HS_BURST_CAP_SIZE / HS_USB_PKT_SIZE;
-- dev->rx_urb_size = DEFAULT_HS_BURST_CAP_SIZE;
-+ dev->rx_urb_size = packetsize ? packetsize : DEFAULT_HS_BURST_CAP_SIZE;
-+ burst_cap = dev->rx_urb_size / HS_USB_PKT_SIZE;
- } else {
-- burst_cap = DEFAULT_FS_BURST_CAP_SIZE / FS_USB_PKT_SIZE;
-- dev->rx_urb_size = DEFAULT_FS_BURST_CAP_SIZE;
-+ dev->rx_urb_size = packetsize ? packetsize : DEFAULT_FS_BURST_CAP_SIZE;
-+ burst_cap = dev->rx_urb_size / FS_USB_PKT_SIZE;
- }
-
- netif_dbg(dev, ifup, dev->net, "rx_urb_size=%ld\n",
diff --git a/target/linux/brcm2708/patches-4.4/0229-reboot-Use-power-off-rather-than-busy-spinning-when-.patch b/target/linux/brcm2708/patches-4.4/0229-reboot-Use-power-off-rather-than-busy-spinning-when-.patch
deleted file mode 100644
index 57b01a5..0000000
--- a/target/linux/brcm2708/patches-4.4/0229-reboot-Use-power-off-rather-than-busy-spinning-when-.patch
+++ /dev/null
@@ -1,25 +0,0 @@
-From 596c6fd4ff5ba8e472442d59bb782f2a0ff16d71 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Tue, 5 Apr 2016 19:40:12 +0100
-Subject: [PATCH] reboot: Use power off rather than busy spinning when halt is
- requested
-
----
- arch/arm/kernel/reboot.c | 6 +-----
- 1 file changed, 1 insertion(+), 5 deletions(-)
-
---- a/arch/arm/kernel/reboot.c
-+++ b/arch/arm/kernel/reboot.c
-@@ -102,11 +102,7 @@ void machine_shutdown(void)
- */
- void machine_halt(void)
- {
-- local_irq_disable();
-- smp_send_stop();
--
-- local_irq_disable();
-- while (1);
-+ machine_power_off();
- }
-
- /*
diff --git a/target/linux/brcm2708/patches-4.4/0230-Revert-bcm2835-dma-Fix-dreq-not-set-for-slave-transf.patch b/target/linux/brcm2708/patches-4.4/0230-Revert-bcm2835-dma-Fix-dreq-not-set-for-slave-transf.patch
deleted file mode 100644
index 9cb3ed6..0000000
--- a/target/linux/brcm2708/patches-4.4/0230-Revert-bcm2835-dma-Fix-dreq-not-set-for-slave-transf.patch
+++ /dev/null
@@ -1,31 +0,0 @@
-From c10f65e711c4707173388502776d8731e296c601 Mon Sep 17 00:00:00 2001
-From: HiassofT <github at hias.horus.com>
-Date: Wed, 6 Apr 2016 21:45:01 +0200
-Subject: [PATCH] Revert "bcm2835-dma: Fix dreq not set for slave transfers"
-
-This reverts commit 8ad957e866a1fe1450f663f2b00a57d7de44904c.
-
-
-
-DMA channels are set in devicetree, thus dreq will be set,
-
-and this commit is no longer needed.
-
-
-
-Signed-off-by: Matthias Reichl <hias at horus.com>
----
- drivers/dma/bcm2835-dma.c | 2 --
- 1 file changed, 2 deletions(-)
-
---- a/drivers/dma/bcm2835-dma.c
-+++ b/drivers/dma/bcm2835-dma.c
-@@ -679,8 +679,6 @@ static int bcm2835_dma_slave_config(stru
- }
-
- c->cfg = *cfg;
-- if (!c->dreq)
-- c->dreq = cfg->slave_id;
-
- return 0;
- }
diff --git a/target/linux/brcm2708/patches-4.4/0231-RPi-config-Add-CONFIG_PWM_PCA9685-for-NXP-PCA9685-dr.patch b/target/linux/brcm2708/patches-4.4/0231-RPi-config-Add-CONFIG_PWM_PCA9685-for-NXP-PCA9685-dr.patch
deleted file mode 100644
index 5bfde8d..0000000
--- a/target/linux/brcm2708/patches-4.4/0231-RPi-config-Add-CONFIG_PWM_PCA9685-for-NXP-PCA9685-dr.patch
+++ /dev/null
@@ -1,92 +0,0 @@
-From da8208f8af795b0696e591bd85bedf2990775451 Mon Sep 17 00:00:00 2001
-From: Dave Stevenson <6by9 at users.noreply.github.com>
-Date: Fri, 1 Apr 2016 15:28:46 +0100
-Subject: [PATCH] RPi config: Add CONFIG_PWM_PCA9685 for NXP PCA9685 driver
- over I2C
-
-Includes DT overlay to configure it.
-
-Signed-off-by: Dave Stevenson <6by9 at users.noreply.github.com>
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 6 +++++
- .../boot/dts/overlays/i2c-pwm-pca9685a-overlay.dts | 26 ++++++++++++++++++++++
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 5 files changed, 35 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/i2c-pwm-pca9685a-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -30,6 +30,7 @@ dtbo-$(RPI_DT_OVERLAYS) += hy28b.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c-rtc.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c-gpio.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c-mux-pca9548a.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += i2c-pwm-pca9685a.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c0-bcm2708.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c1-bcm2708.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2s-mmap.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -366,6 +366,12 @@ Load: dtoverlay=i2c-mux-pca9548a,<para
- Params: addr I2C address of PCA9548A (default 0x70)
-
-
-+Name: i2c-pwm-pca9685a
-+Info: Adds support for an NXP PCA9685A I2C PWM controller on i2c_arm
-+Load: dtoverlay=i2c-pwm-pca9685a,<param>=<val>
-+Params: addr I2C address of PCA9685A (default 0x40)
-+
-+
- Name: i2c-rtc
- Info: Adds support for a number of I2C Real Time Clock devices
- Load: dtoverlay=i2c-rtc,<param>=<val>
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/i2c-pwm-pca9685a-overlay.dts
-@@ -0,0 +1,26 @@
-+// Definitions for NXP PCA9685A I2C PWM controller on ARM I2C bus.
-+/dts-v1/;
-+/plugin/;
-+
-+/{
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&i2c_arm>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ pca: pca at 40 {
-+ compatible = "nxp,pca9685";
-+ #pwm-cells = <2>;
-+ reg = <0x40>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+ __overrides__ {
-+ addr = <&pca>,"reg:0";
-+ };
-+};
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -1122,6 +1122,7 @@ CONFIG_MCP320X=m
- CONFIG_MCP3422=m
- CONFIG_DHT11=m
- CONFIG_PWM_BCM2835=m
-+CONFIG_PWM_PCA9685=m
- CONFIG_RASPBERRYPI_FIRMWARE=y
- CONFIG_EXT4_FS=y
- CONFIG_EXT4_FS_POSIX_ACL=y
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -1129,6 +1129,7 @@ CONFIG_MCP320X=m
- CONFIG_MCP3422=m
- CONFIG_DHT11=m
- CONFIG_PWM_BCM2835=m
-+CONFIG_PWM_PCA9685=m
- CONFIG_RASPBERRYPI_FIRMWARE=y
- CONFIG_EXT4_FS=y
- CONFIG_EXT4_FS_POSIX_ACL=y
diff --git a/target/linux/brcm2708/patches-4.4/0232-BCM270X_DT-Don-t-generate-linux-phandle-props.patch b/target/linux/brcm2708/patches-4.4/0232-BCM270X_DT-Don-t-generate-linux-phandle-props.patch
deleted file mode 100644
index d17915b..0000000
--- a/target/linux/brcm2708/patches-4.4/0232-BCM270X_DT-Don-t-generate-linux-phandle-props.patch
+++ /dev/null
@@ -1,36 +0,0 @@
-From 552a516a854306ced246dc0dfd73a52830d2bbfd Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 8 Apr 2016 17:43:27 +0100
-Subject: [PATCH] BCM270X_DT: Don't generate "linux,phandle" props
-
-The EPAPR standard says to use "phandle" properties to store phandles,
-rather than the deprecated "linux,phandle" version. By default, dtc
-generates both, but adding "-H epapr" causes it to only generate
-"phandle"s, saving some space and clutter.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/Makefile | 2 +-
- scripts/Makefile.lib | 2 +-
- 2 files changed, 2 insertions(+), 2 deletions(-)
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -813,5 +813,5 @@ clean-files := *.dtb
-
- # Enable fixups to support overlays on BCM2708 platforms
- ifeq ($(RPI_DT_OVERLAYS),y)
-- DTC_FLAGS ?= -@
-+ DTC_FLAGS ?= -@ -H epapr
- endif
---- a/scripts/Makefile.lib
-+++ b/scripts/Makefile.lib
-@@ -294,7 +294,7 @@ $(obj)/%.dtb: $(src)/%.dts FORCE
-
- quiet_cmd_dtco = DTCO $@
- cmd_dtco = $(CPP) $(dtc_cpp_flags) -x assembler-with-cpp -o $(dtc-tmp) $< ; \
-- $(objtree)/scripts/dtc/dtc -@ -O dtb -o $@ -b 0 \
-+ $(objtree)/scripts/dtc/dtc -@ -H epapr -O dtb -o $@ -b 0 \
- -i $(dir $<) $(DTC_FLAGS) \
- -d $(depfile).dtc.tmp $(dtc-tmp) ; \
- cat $(depfile).pre.tmp $(depfile).dtc.tmp > $(depfile)
diff --git a/target/linux/brcm2708/patches-4.4/0233-V4L2-driver-updates-1393.patch b/target/linux/brcm2708/patches-4.4/0233-V4L2-driver-updates-1393.patch
deleted file mode 100644
index 5804892..0000000
--- a/target/linux/brcm2708/patches-4.4/0233-V4L2-driver-updates-1393.patch
+++ /dev/null
@@ -1,718 +0,0 @@
-From 21e3542368e5df2eecb87f32187cb7a64c55fd04 Mon Sep 17 00:00:00 2001
-From: 6by9 <6by9 at users.noreply.github.com>
-Date: Fri, 8 Apr 2016 18:15:43 +0100
-Subject: [PATCH] V4L2 driver updates (#1393)
-
-* BCM2835-V4L2: Correct ISO control and add V4L2_CID_ISO_SENSITIVITY_AUTO
-
-https://github.com/raspberrypi/linux/issues/1251
-
-V4L2_CID_ISO_SENSITIVITY was not advertising ISO*1000 as it should.
-V4L2_CID_ISO_SENSITIVITY_AUTO was not implemented, so was taking
-V4L2_CID_ISO_SENSITIVITY as 0 for auto mode.
-Still accepts 0 for auto, but also abides by the new parameter.
-
-Signed-off-by: Dave Stevenson <6by9 at users.noreply.github.com>
-
-* BCM2835-V4L2: Add a video_nr parameter.
-
-Adds a kernel parameter "video_nr" to specify the preferred
-/dev/videoX device node.
-https://www.raspberrypi.org/forums/viewtopic.php?f=38&t=136120&p=905545
-
-Signed-off-by: Dave Stevenson <6by9 at users.noreply.github.com>
-
-* BCM2835-V4L2: Add support for multiple cameras
-
-Ask GPU on load how many cameras have been detected, and
-enumerate that number of devices.
-Only applicable on the Compute Module as no other device
-exposes multiple CSI2 interfaces.
-
-Signed-off-by: Dave Stevenson <6by9 at users.noreply.github.com>
-
-* BCM2835-V4L2: Add control of the overlay location and alpha.
-
-Actually do something useful in vidioc_s_fmt_vid_overlay and
-vidioc_try_fmt_vid_overlay, rather than effectively having
-read-only fields.
-
-Signed-off-by: Dave Stevenson <6by9 at users.noreply.github.com>
-
-* BCM2835-V4L2: V4L2-Compliance failure fix
-
-VIDIOC_TRY_FMT was failing due to bytesperline not
-being set correctly by default.
-
-Signed-off-by: Dave Stevenson <6by9 at users.noreply.github.com>
-
-* BCM2835-V4L2: Make all module parameters static
-
-Clean up to correct variable scope
-
-Signed-off-by: Dave Stevenson <6by9 at users.noreply.github.com>
----
- drivers/media/platform/bcm2835/bcm2835-camera.c | 372 +++++++++++++++--------
- drivers/media/platform/bcm2835/bcm2835-camera.h | 19 +-
- drivers/media/platform/bcm2835/controls.c | 31 +-
- drivers/media/platform/bcm2835/mmal-parameters.h | 33 ++
- 4 files changed, 320 insertions(+), 135 deletions(-)
-
---- a/drivers/media/platform/bcm2835/bcm2835-camera.c
-+++ b/drivers/media/platform/bcm2835/bcm2835-camera.c
-@@ -45,6 +45,8 @@
- #define MAX_VIDEO_MODE_WIDTH 1280
- #define MAX_VIDEO_MODE_HEIGHT 720
-
-+#define MAX_BCM2835_CAMERAS 2
-+
- MODULE_DESCRIPTION("Broadcom 2835 MMAL video capture");
- MODULE_AUTHOR("Vincent Sanders");
- MODULE_LICENSE("GPL");
-@@ -54,8 +56,13 @@ int bcm2835_v4l2_debug;
- module_param_named(debug, bcm2835_v4l2_debug, int, 0644);
- MODULE_PARM_DESC(bcm2835_v4l2_debug, "Debug level 0-2");
-
--int max_video_width = MAX_VIDEO_MODE_WIDTH;
--int max_video_height = MAX_VIDEO_MODE_HEIGHT;
-+#define UNSET (-1)
-+static int video_nr[] = {[0 ... (MAX_BCM2835_CAMERAS - 1)] = UNSET };
-+module_param_array(video_nr, int, NULL, 0644);
-+MODULE_PARM_DESC(video_nr, "videoX start numbers, -1 is autodetect");
-+
-+static int max_video_width = MAX_VIDEO_MODE_WIDTH;
-+static int max_video_height = MAX_VIDEO_MODE_HEIGHT;
- module_param(max_video_width, int, S_IRUSR | S_IWUSR | S_IRGRP | S_IROTH);
- MODULE_PARM_DESC(max_video_width, "Threshold for video mode");
- module_param(max_video_height, int, S_IRUSR | S_IWUSR | S_IRGRP | S_IROTH);
-@@ -70,11 +77,12 @@ MODULE_PARM_DESC(max_video_height, "Thre
- * our function table list (actually switch to an alternate set, but same
- * result).
- */
--int gst_v4l2src_is_broken = 0;
-+static int gst_v4l2src_is_broken;
- module_param(gst_v4l2src_is_broken, int, S_IRUSR | S_IWUSR | S_IRGRP | S_IROTH);
- MODULE_PARM_DESC(gst_v4l2src_is_broken, "If non-zero, enable workaround for Gstreamer");
-
--static struct bm2835_mmal_dev *gdev; /* global device data */
-+/* global device data array */
-+static struct bm2835_mmal_dev *gdev[MAX_BCM2835_CAMERAS];
-
- #define FPS_MIN 1
- #define FPS_MAX 90
-@@ -413,6 +421,17 @@ static int enable_camera(struct bm2835_m
- {
- int ret;
- if (!dev->camera_use_count) {
-+ ret = vchiq_mmal_port_parameter_set(
-+ dev->instance,
-+ &dev->component[MMAL_COMPONENT_CAMERA]->control,
-+ MMAL_PARAMETER_CAMERA_NUM, &dev->camera_num,
-+ sizeof(dev->camera_num));
-+ if (ret < 0) {
-+ v4l2_err(&dev->v4l2_dev,
-+ "Failed setting camera num, ret %d\n", ret);
-+ return -EINVAL;
-+ }
-+
- ret = vchiq_mmal_component_enable(
- dev->instance,
- dev->component[MMAL_COMPONENT_CAMERA]);
-@@ -647,6 +666,30 @@ static struct vb2_ops bm2835_mmal_video_
- IOCTL operations
- ------------------------------------------------------------------*/
-
-+static int set_overlay_params(struct bm2835_mmal_dev *dev,
-+ struct vchiq_mmal_port *port)
-+{
-+ int ret;
-+ struct mmal_parameter_displayregion prev_config = {
-+ .set = MMAL_DISPLAY_SET_LAYER | MMAL_DISPLAY_SET_ALPHA |
-+ MMAL_DISPLAY_SET_DEST_RECT | MMAL_DISPLAY_SET_FULLSCREEN,
-+ .layer = PREVIEW_LAYER,
-+ .alpha = dev->overlay.global_alpha,
-+ .fullscreen = 0,
-+ .dest_rect = {
-+ .x = dev->overlay.w.left,
-+ .y = dev->overlay.w.top,
-+ .width = dev->overlay.w.width,
-+ .height = dev->overlay.w.height,
-+ },
-+ };
-+ ret = vchiq_mmal_port_parameter_set(dev->instance, port,
-+ MMAL_PARAMETER_DISPLAYREGION,
-+ &prev_config, sizeof(prev_config));
-+
-+ return ret;
-+}
-+
- /* overlay ioctl */
- static int vidioc_enum_fmt_vid_overlay(struct file *file, void *priv,
- struct v4l2_fmtdesc *f)
-@@ -678,10 +721,31 @@ static int vidioc_g_fmt_vid_overlay(stru
- static int vidioc_try_fmt_vid_overlay(struct file *file, void *priv,
- struct v4l2_format *f)
- {
-- /* Only support one format so get the current one. */
-- vidioc_g_fmt_vid_overlay(file, priv, f);
-+ struct bm2835_mmal_dev *dev = video_drvdata(file);
-
-- /* todo: allow the size and/or offset to be changed. */
-+ f->fmt.win.field = V4L2_FIELD_NONE;
-+ f->fmt.win.chromakey = 0;
-+ f->fmt.win.clips = NULL;
-+ f->fmt.win.clipcount = 0;
-+ f->fmt.win.bitmap = NULL;
-+
-+ v4l_bound_align_image(&f->fmt.win.w.width, MIN_WIDTH, MAX_WIDTH, 1,
-+ &f->fmt.win.w.height, MIN_HEIGHT, MAX_HEIGHT,
-+ 1, 0);
-+ v4l_bound_align_image(&f->fmt.win.w.left, MIN_WIDTH, MAX_WIDTH, 1,
-+ &f->fmt.win.w.top, MIN_HEIGHT, MAX_HEIGHT,
-+ 1, 0);
-+
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "Overlay: Now w/h %dx%d l/t %dx%d\n",
-+ f->fmt.win.w.width, f->fmt.win.w.height,
-+ f->fmt.win.w.left, f->fmt.win.w.top);
-+
-+ v4l2_dump_win_format(1,
-+ bcm2835_v4l2_debug,
-+ &dev->v4l2_dev,
-+ &f->fmt.win,
-+ __func__);
- return 0;
- }
-
-@@ -693,8 +757,11 @@ static int vidioc_s_fmt_vid_overlay(stru
- vidioc_try_fmt_vid_overlay(file, priv, f);
-
- dev->overlay = f->fmt.win;
-+ if (dev->component[MMAL_COMPONENT_PREVIEW]->enabled) {
-+ set_overlay_params(dev,
-+ &dev->component[MMAL_COMPONENT_PREVIEW]->input[0]);
-+ }
-
-- /* todo: program the preview port parameters */
- return 0;
- }
-
-@@ -704,20 +771,6 @@ static int vidioc_overlay(struct file *f
- struct bm2835_mmal_dev *dev = video_drvdata(file);
- struct vchiq_mmal_port *src;
- struct vchiq_mmal_port *dst;
-- struct mmal_parameter_displayregion prev_config = {
-- .set = MMAL_DISPLAY_SET_LAYER | MMAL_DISPLAY_SET_ALPHA |
-- MMAL_DISPLAY_SET_DEST_RECT | MMAL_DISPLAY_SET_FULLSCREEN,
-- .layer = PREVIEW_LAYER,
-- .alpha = 255,
-- .fullscreen = 0,
-- .dest_rect = {
-- .x = dev->overlay.w.left,
-- .y = dev->overlay.w.top,
-- .width = dev->overlay.w.width,
-- .height = dev->overlay.w.height,
-- },
-- };
--
- if ((on && dev->component[MMAL_COMPONENT_PREVIEW]->enabled) ||
- (!on && !dev->component[MMAL_COMPONENT_PREVIEW]->enabled))
- return 0; /* already in requested state */
-@@ -749,9 +802,7 @@ static int vidioc_overlay(struct file *f
- if (ret < 0)
- goto error;
-
-- ret = vchiq_mmal_port_parameter_set(dev->instance, dst,
-- MMAL_PARAMETER_DISPLAYREGION,
-- &prev_config, sizeof(prev_config));
-+ ret = set_overlay_params(dev, dst);
- if (ret < 0)
- goto error;
-
-@@ -782,6 +833,9 @@ static int vidioc_g_fbuf(struct file *fi
- struct vchiq_mmal_port *preview_port =
- &dev->component[MMAL_COMPONENT_CAMERA]->
- output[MMAL_CAMERA_PORT_PREVIEW];
-+
-+ a->capability = V4L2_FBUF_CAP_EXTERNOVERLAY |
-+ V4L2_FBUF_CAP_GLOBAL_ALPHA;
- a->flags = V4L2_FBUF_FLAG_OVERLAY;
- a->fmt.width = preview_port->es.video.width;
- a->fmt.height = preview_port->es.video.height;
-@@ -1445,6 +1499,34 @@ static struct video_device vdev_template
- .release = video_device_release_empty,
- };
-
-+static int get_num_cameras(struct vchiq_mmal_instance *instance)
-+{
-+ int ret;
-+ struct vchiq_mmal_component *cam_info_component;
-+ struct mmal_parameter_camera_info_t cam_info = {0};
-+ int param_size = sizeof(cam_info);
-+
-+ /* create a camera_info component */
-+ ret = vchiq_mmal_component_init(instance, "camera_info",
-+ &cam_info_component);
-+ if (ret < 0)
-+ /* Unusual failure - let's guess one camera. */
-+ return 1;
-+
-+ if (vchiq_mmal_port_parameter_get(instance,
-+ &cam_info_component->control,
-+ MMAL_PARAMETER_CAMERA_INFO,
-+ &cam_info,
-+ ¶m_size)) {
-+ pr_info("Failed to get camera info\n");
-+ }
-+
-+ vchiq_mmal_component_finalise(instance,
-+ cam_info_component);
-+
-+ return cam_info.num_cameras;
-+}
-+
- static int set_camera_parameters(struct vchiq_mmal_instance *instance,
- struct vchiq_mmal_component *camera)
- {
-@@ -1685,7 +1767,9 @@ static int __init bm2835_mmal_init_devic
- /* video device needs to be able to access instance data */
- video_set_drvdata(vfd, dev);
-
-- ret = video_register_device(vfd, VFL_TYPE_GRABBER, -1);
-+ ret = video_register_device(vfd,
-+ VFL_TYPE_GRABBER,
-+ video_nr[dev->camera_num]);
- if (ret < 0)
- return ret;
-
-@@ -1696,10 +1780,52 @@ static int __init bm2835_mmal_init_devic
- return 0;
- }
-
-+void bcm2835_cleanup_instance(struct bm2835_mmal_dev *dev)
-+{
-+ if (!dev)
-+ return;
-+
-+ v4l2_info(&dev->v4l2_dev, "unregistering %s\n",
-+ video_device_node_name(&dev->vdev));
-+
-+ video_unregister_device(&dev->vdev);
-+
-+ if (dev->capture.encode_component) {
-+ v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
-+ "mmal_exit - disconnect tunnel\n");
-+ vchiq_mmal_port_connect_tunnel(dev->instance,
-+ dev->capture.camera_port, NULL);
-+ vchiq_mmal_component_disable(dev->instance,
-+ dev->capture.encode_component);
-+ }
-+ vchiq_mmal_component_disable(dev->instance,
-+ dev->component[MMAL_COMPONENT_CAMERA]);
-+
-+ vchiq_mmal_component_finalise(dev->instance,
-+ dev->
-+ component[MMAL_COMPONENT_VIDEO_ENCODE]);
-+
-+ vchiq_mmal_component_finalise(dev->instance,
-+ dev->
-+ component[MMAL_COMPONENT_IMAGE_ENCODE]);
-+
-+ vchiq_mmal_component_finalise(dev->instance,
-+ dev->component[MMAL_COMPONENT_PREVIEW]);
-+
-+ vchiq_mmal_component_finalise(dev->instance,
-+ dev->component[MMAL_COMPONENT_CAMERA]);
-+
-+ v4l2_ctrl_handler_free(&dev->ctrl_handler);
-+
-+ v4l2_device_unregister(&dev->v4l2_dev);
-+
-+ kfree(dev);
-+}
-+
- static struct v4l2_format default_v4l2_format = {
- .fmt.pix.pixelformat = V4L2_PIX_FMT_JPEG,
- .fmt.pix.width = 1024,
-- .fmt.pix.bytesperline = 1024,
-+ .fmt.pix.bytesperline = 0,
- .fmt.pix.height = 768,
- .fmt.pix.sizeimage = 1024*768,
- };
-@@ -1709,76 +1835,93 @@ static int __init bm2835_mmal_init(void)
- int ret;
- struct bm2835_mmal_dev *dev;
- struct vb2_queue *q;
-+ int camera;
-+ unsigned int num_cameras;
-+ struct vchiq_mmal_instance *instance;
-
-- dev = kzalloc(sizeof(*gdev), GFP_KERNEL);
-- if (!dev)
-- return -ENOMEM;
--
-- /* setup device defaults */
-- dev->overlay.w.left = 150;
-- dev->overlay.w.top = 50;
-- dev->overlay.w.width = 1024;
-- dev->overlay.w.height = 768;
-- dev->overlay.clipcount = 0;
-- dev->overlay.field = V4L2_FIELD_NONE;
--
-- dev->capture.fmt = &formats[3]; /* JPEG */
--
-- /* v4l device registration */
-- snprintf(dev->v4l2_dev.name, sizeof(dev->v4l2_dev.name),
-- "%s", BM2835_MMAL_MODULE_NAME);
-- ret = v4l2_device_register(NULL, &dev->v4l2_dev);
-- if (ret)
-- goto free_dev;
--
-- /* setup v4l controls */
-- ret = bm2835_mmal_init_controls(dev, &dev->ctrl_handler);
-- if (ret < 0)
-- goto unreg_dev;
-- dev->v4l2_dev.ctrl_handler = &dev->ctrl_handler;
--
-- /* mmal init */
-- ret = mmal_init(dev);
-+ ret = vchiq_mmal_init(&instance);
- if (ret < 0)
-- goto unreg_dev;
-+ return ret;
-
-- /* initialize queue */
-- q = &dev->capture.vb_vidq;
-- memset(q, 0, sizeof(*q));
-- q->type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
-- q->io_modes = VB2_MMAP | VB2_USERPTR | VB2_READ;
-- q->drv_priv = dev;
-- q->buf_struct_size = sizeof(struct mmal_buffer);
-- q->ops = &bm2835_mmal_video_qops;
-- q->mem_ops = &vb2_vmalloc_memops;
-- q->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC;
-- ret = vb2_queue_init(q);
-- if (ret < 0)
-- goto unreg_dev;
-+ num_cameras = get_num_cameras(instance);
-+ if (num_cameras > MAX_BCM2835_CAMERAS)
-+ num_cameras = MAX_BCM2835_CAMERAS;
-+
-+ for (camera = 0; camera < num_cameras; camera++) {
-+ dev = kzalloc(sizeof(struct bm2835_mmal_dev), GFP_KERNEL);
-+ if (!dev)
-+ return -ENOMEM;
-+
-+ dev->camera_num = camera;
-+
-+ /* setup device defaults */
-+ dev->overlay.w.left = 150;
-+ dev->overlay.w.top = 50;
-+ dev->overlay.w.width = 1024;
-+ dev->overlay.w.height = 768;
-+ dev->overlay.clipcount = 0;
-+ dev->overlay.field = V4L2_FIELD_NONE;
-+ dev->overlay.global_alpha = 255;
-+
-+ dev->capture.fmt = &formats[3]; /* JPEG */
-+
-+ /* v4l device registration */
-+ snprintf(dev->v4l2_dev.name, sizeof(dev->v4l2_dev.name),
-+ "%s", BM2835_MMAL_MODULE_NAME);
-+ ret = v4l2_device_register(NULL, &dev->v4l2_dev);
-+ if (ret)
-+ goto free_dev;
-
-- /* v4l2 core mutex used to protect all fops and v4l2 ioctls. */
-- mutex_init(&dev->mutex);
-+ /* setup v4l controls */
-+ ret = bm2835_mmal_init_controls(dev, &dev->ctrl_handler);
-+ if (ret < 0)
-+ goto unreg_dev;
-+ dev->v4l2_dev.ctrl_handler = &dev->ctrl_handler;
-+
-+ /* mmal init */
-+ dev->instance = instance;
-+ ret = mmal_init(dev);
-+ if (ret < 0)
-+ goto unreg_dev;
-+
-+ /* initialize queue */
-+ q = &dev->capture.vb_vidq;
-+ memset(q, 0, sizeof(*q));
-+ q->type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
-+ q->io_modes = VB2_MMAP | VB2_USERPTR | VB2_READ;
-+ q->drv_priv = dev;
-+ q->buf_struct_size = sizeof(struct mmal_buffer);
-+ q->ops = &bm2835_mmal_video_qops;
-+ q->mem_ops = &vb2_vmalloc_memops;
-+ q->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC;
-+ ret = vb2_queue_init(q);
-+ if (ret < 0)
-+ goto unreg_dev;
-+
-+ /* v4l2 core mutex used to protect all fops and v4l2 ioctls. */
-+ mutex_init(&dev->mutex);
-+
-+ /* initialise video devices */
-+ ret = bm2835_mmal_init_device(dev, &dev->vdev);
-+ if (ret < 0)
-+ goto unreg_dev;
-+
-+ /* Really want to call vidioc_s_fmt_vid_cap with the default
-+ * format, but currently the APIs don't join up.
-+ */
-+ ret = mmal_setup_components(dev, &default_v4l2_format);
-+ if (ret < 0) {
-+ v4l2_err(&dev->v4l2_dev,
-+ "%s: could not setup components\n", __func__);
-+ goto unreg_dev;
-+ }
-
-- /* initialise video devices */
-- ret = bm2835_mmal_init_device(dev, &dev->vdev);
-- if (ret < 0)
-- goto unreg_dev;
-+ v4l2_info(&dev->v4l2_dev,
-+ "Broadcom 2835 MMAL video capture ver %s loaded.\n",
-+ BM2835_MMAL_VERSION);
-
-- /* Really want to call vidioc_s_fmt_vid_cap with the default
-- * format, but currently the APIs don't join up.
-- */
-- ret = mmal_setup_components(dev, &default_v4l2_format);
-- if (ret < 0) {
-- v4l2_err(&dev->v4l2_dev,
-- "%s: could not setup components\n", __func__);
-- goto unreg_dev;
-+ gdev[camera] = dev;
- }
--
-- v4l2_info(&dev->v4l2_dev,
-- "Broadcom 2835 MMAL video capture ver %s loaded.\n",
-- BM2835_MMAL_VERSION);
--
-- gdev = dev;
- return 0;
-
- unreg_dev:
-@@ -1788,8 +1931,11 @@ unreg_dev:
- free_dev:
- kfree(dev);
-
-- v4l2_err(&dev->v4l2_dev,
-- "%s: error %d while loading driver\n",
-+ for ( ; camera > 0; camera--) {
-+ bcm2835_cleanup_instance(gdev[camera]);
-+ gdev[camera] = NULL;
-+ }
-+ pr_info("%s: error %d while loading driver\n",
- BM2835_MMAL_MODULE_NAME, ret);
-
- return ret;
-@@ -1797,46 +1943,14 @@ free_dev:
-
- static void __exit bm2835_mmal_exit(void)
- {
-- if (!gdev)
-- return;
--
-- v4l2_info(&gdev->v4l2_dev, "unregistering %s\n",
-- video_device_node_name(&gdev->vdev));
-+ int camera;
-+ struct vchiq_mmal_instance *instance = gdev[0]->instance;
-
-- video_unregister_device(&gdev->vdev);
--
-- if (gdev->capture.encode_component) {
-- v4l2_dbg(1, bcm2835_v4l2_debug, &gdev->v4l2_dev,
-- "mmal_exit - disconnect tunnel\n");
-- vchiq_mmal_port_connect_tunnel(gdev->instance,
-- gdev->capture.camera_port, NULL);
-- vchiq_mmal_component_disable(gdev->instance,
-- gdev->capture.encode_component);
-+ for (camera = 0; camera < MAX_BCM2835_CAMERAS; camera++) {
-+ bcm2835_cleanup_instance(gdev[camera]);
-+ gdev[camera] = NULL;
- }
-- vchiq_mmal_component_disable(gdev->instance,
-- gdev->component[MMAL_COMPONENT_CAMERA]);
--
-- vchiq_mmal_component_finalise(gdev->instance,
-- gdev->
-- component[MMAL_COMPONENT_VIDEO_ENCODE]);
--
-- vchiq_mmal_component_finalise(gdev->instance,
-- gdev->
-- component[MMAL_COMPONENT_IMAGE_ENCODE]);
--
-- vchiq_mmal_component_finalise(gdev->instance,
-- gdev->component[MMAL_COMPONENT_PREVIEW]);
--
-- vchiq_mmal_component_finalise(gdev->instance,
-- gdev->component[MMAL_COMPONENT_CAMERA]);
--
-- vchiq_mmal_finalise(gdev->instance);
--
-- v4l2_ctrl_handler_free(&gdev->ctrl_handler);
--
-- v4l2_device_unregister(&gdev->v4l2_dev);
--
-- kfree(gdev);
-+ vchiq_mmal_finalise(instance);
- }
-
- module_init(bm2835_mmal_init);
---- a/drivers/media/platform/bcm2835/bcm2835-camera.h
-+++ b/drivers/media/platform/bcm2835/bcm2835-camera.h
-@@ -15,7 +15,7 @@
- * core driver device
- */
-
--#define V4L2_CTRL_COUNT 28 /* number of v4l controls */
-+#define V4L2_CTRL_COUNT 29 /* number of v4l controls */
-
- enum {
- MMAL_COMPONENT_CAMERA = 0,
-@@ -58,6 +58,8 @@ struct bm2835_mmal_dev {
- enum mmal_parameter_exposuremeteringmode metering_mode;
- unsigned int manual_shutter_speed;
- bool exp_auto_priority;
-+ bool manual_iso_enabled;
-+ uint32_t iso;
-
- /* allocated mmal instance and components */
- struct vchiq_mmal_instance *instance;
-@@ -104,6 +106,8 @@ struct bm2835_mmal_dev {
-
- } capture;
-
-+ unsigned int camera_num;
-+
- };
-
- int bm2835_mmal_init_controls(
-@@ -124,3 +128,16 @@ int set_framerate_params(struct bm2835_m
- (pix_fmt)->pixelformat, (pix_fmt)->bytesperline, \
- (pix_fmt)->sizeimage, (pix_fmt)->colorspace, (pix_fmt)->priv); \
- }
-+#define v4l2_dump_win_format(level, debug, dev, win_fmt, desc) \
-+{ \
-+ v4l2_dbg(level, debug, dev, \
-+"%s: w %u h %u l %u t %u field %u chromakey %06X clip %p " \
-+"clipcount %u bitmap %p\n", \
-+ desc == NULL ? "" : desc, \
-+ (win_fmt)->w.width, (win_fmt)->w.height, \
-+ (win_fmt)->w.left, (win_fmt)->w.top, \
-+ (win_fmt)->field, \
-+ (win_fmt)->chromakey, \
-+ (win_fmt)->clips, (win_fmt)->clipcount, \
-+ (win_fmt)->bitmap); \
-+}
---- a/drivers/media/platform/bcm2835/controls.c
-+++ b/drivers/media/platform/bcm2835/controls.c
-@@ -49,10 +49,13 @@ static const s64 ev_bias_qmenu[] = {
- 4000
- };
-
--/* Supported ISO values
-+/* Supported ISO values (*1000)
- * ISOO = auto ISO
- */
- static const s64 iso_qmenu[] = {
-+ 0, 100000, 200000, 400000, 800000,
-+};
-+static const uint32_t iso_values[] = {
- 0, 100, 200, 400, 800,
- };
-
-@@ -201,7 +204,7 @@ static int ctrl_set_value(struct bm2835_
- &u32_value, sizeof(u32_value));
- }
-
--static int ctrl_set_value_menu(struct bm2835_mmal_dev *dev,
-+static int ctrl_set_iso(struct bm2835_mmal_dev *dev,
- struct v4l2_ctrl *ctrl,
- const struct bm2835_mmal_v4l2_ctrl *mmal_ctrl)
- {
-@@ -211,12 +214,23 @@ static int ctrl_set_value_menu(struct bm
- if (ctrl->val > mmal_ctrl->max || ctrl->val < mmal_ctrl->min)
- return 1;
-
-+ if (ctrl->id == V4L2_CID_ISO_SENSITIVITY)
-+ dev->iso = iso_values[ctrl->val];
-+ else if (ctrl->id == V4L2_CID_ISO_SENSITIVITY_AUTO)
-+ dev->manual_iso_enabled =
-+ (ctrl->val == V4L2_ISO_SENSITIVITY_MANUAL ?
-+ true :
-+ false);
-+
- control = &dev->component[MMAL_COMPONENT_CAMERA]->control;
-
-- u32_value = mmal_ctrl->imenu[ctrl->val];
-+ if (dev->manual_iso_enabled)
-+ u32_value = dev->iso;
-+ else
-+ u32_value = 0;
-
- return vchiq_mmal_port_parameter_set(dev->instance, control,
-- mmal_ctrl->mmal_id,
-+ MMAL_PARAMETER_ISO,
- &u32_value, sizeof(u32_value));
- }
-
-@@ -956,7 +970,14 @@ static const struct bm2835_mmal_v4l2_ctr
- V4L2_CID_ISO_SENSITIVITY, MMAL_CONTROL_TYPE_INT_MENU,
- 0, ARRAY_SIZE(iso_qmenu) - 1, 0, 1, iso_qmenu,
- MMAL_PARAMETER_ISO,
-- &ctrl_set_value_menu,
-+ &ctrl_set_iso,
-+ false
-+ },
-+ {
-+ V4L2_CID_ISO_SENSITIVITY_AUTO, MMAL_CONTROL_TYPE_STD_MENU,
-+ 0, 1, V4L2_ISO_SENSITIVITY_AUTO, 1, NULL,
-+ MMAL_PARAMETER_ISO,
-+ &ctrl_set_iso,
- false
- },
- {
---- a/drivers/media/platform/bcm2835/mmal-parameters.h
-+++ b/drivers/media/platform/bcm2835/mmal-parameters.h
-@@ -654,3 +654,36 @@ struct mmal_parameter_imagefx_parameters
- u32 num_effect_params;
- u32 effect_parameter[MMAL_MAX_IMAGEFX_PARAMETERS];
- };
-+
-+#define MMAL_PARAMETER_CAMERA_INFO_MAX_CAMERAS 4
-+#define MMAL_PARAMETER_CAMERA_INFO_MAX_FLASHES 2
-+#define MMAL_PARAMETER_CAMERA_INFO_MAX_STR_LEN 16
-+
-+struct mmal_parameter_camera_info_camera_t {
-+ u32 port_id;
-+ u32 max_width;
-+ u32 max_height;
-+ u32 lens_present;
-+ u8 camera_name[MMAL_PARAMETER_CAMERA_INFO_MAX_STR_LEN];
-+};
-+
-+enum mmal_parameter_camera_info_flash_type_t {
-+ /* Make values explicit to ensure they match values in config ini */
-+ MMAL_PARAMETER_CAMERA_INFO_FLASH_TYPE_XENON = 0,
-+ MMAL_PARAMETER_CAMERA_INFO_FLASH_TYPE_LED = 1,
-+ MMAL_PARAMETER_CAMERA_INFO_FLASH_TYPE_OTHER = 2,
-+ MMAL_PARAMETER_CAMERA_INFO_FLASH_TYPE_MAX = 0x7FFFFFFF
-+};
-+
-+struct mmal_parameter_camera_info_flash_t {
-+ enum mmal_parameter_camera_info_flash_type_t flash_type;
-+};
-+
-+struct mmal_parameter_camera_info_t {
-+ u32 num_cameras;
-+ u32 num_flashes;
-+ struct mmal_parameter_camera_info_camera_t
-+ cameras[MMAL_PARAMETER_CAMERA_INFO_MAX_CAMERAS];
-+ struct mmal_parameter_camera_info_flash_t
-+ flashes[MMAL_PARAMETER_CAMERA_INFO_MAX_FLASHES];
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0234-bcm2835-sdhost-Reset-the-clock-in-task-context.patch b/target/linux/brcm2708/patches-4.4/0234-bcm2835-sdhost-Reset-the-clock-in-task-context.patch
deleted file mode 100644
index ebb2cc2..0000000
--- a/target/linux/brcm2708/patches-4.4/0234-bcm2835-sdhost-Reset-the-clock-in-task-context.patch
+++ /dev/null
@@ -1,107 +0,0 @@
-From d17f0605ff4b3197eb6667368adc07c5ca859679 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 11 Apr 2016 12:50:58 +0100
-Subject: [PATCH] bcm2835-sdhost: Reset the clock in task context
-
-Since reprogramming the clock can now involve a round-trip to the
-firmware it must not be done at atomic context, and a tasklet
-is not a task.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- drivers/mmc/host/bcm2835-sdhost.c | 25 ++++++++++++++++++-------
- 1 file changed, 18 insertions(+), 7 deletions(-)
-
---- a/drivers/mmc/host/bcm2835-sdhost.c
-+++ b/drivers/mmc/host/bcm2835-sdhost.c
-@@ -185,6 +185,7 @@ struct bcm2835_host {
-
- unsigned int debug:1; /* Enable debug output */
- unsigned int firmware_sets_cdiv:1; /* Let the firmware manage the clock */
-+ unsigned int reset_clock:1; /* Reset the clock fore the next request */
-
- /*DMA part*/
- struct dma_chan *dma_chan_rxtx; /* DMA channel for reads and writes */
-@@ -1505,6 +1506,7 @@ void bcm2835_sdhost_set_clock(struct bcm
- {
- int div = 0; /* Initialized for compiler warning */
- unsigned int input_clock = clock;
-+ unsigned long flags;
-
- if (host->debug)
- pr_info("%s: set_clock(%d)\n", mmc_hostname(host->mmc), clock);
-@@ -1544,13 +1546,17 @@ void bcm2835_sdhost_set_clock(struct bcm
- &msg, sizeof(msg));
-
- clock = max(msg[1], msg[2]);
-+ spin_lock_irqsave(&host->lock, flags);
- } else {
-+ spin_lock_irqsave(&host->lock, flags);
- if (clock < 100000) {
- /* Can't stop the clock, but make it as slow as
- * possible to show willing
- */
- host->cdiv = SDCDIV_MAX_CDIV;
- bcm2835_sdhost_write(host, host->cdiv, SDCDIV);
-+ mmiowb();
-+ spin_unlock_irqrestore(&host->lock, flags);
- return;
- }
-
-@@ -1605,6 +1611,11 @@ void bcm2835_sdhost_set_clock(struct bcm
- bcm2835_sdhost_write(host, clock/2, SDTOUT);
-
- host->mmc->actual_clock = clock;
-+ host->clock = input_clock;
-+ host->reset_clock = 0;
-+
-+ mmiowb();
-+ spin_unlock_irqrestore(&host->lock, flags);
- }
-
- static void bcm2835_sdhost_request(struct mmc_host *mmc, struct mmc_request *mrq)
-@@ -1653,6 +1664,9 @@ static void bcm2835_sdhost_request(struc
- (mrq->data->blocks > host->pio_limit))
- bcm2835_sdhost_prepare_dma(host, mrq->data);
-
-+ if (host->reset_clock)
-+ bcm2835_sdhost_set_clock(host, host->clock);
-+
- spin_lock_irqsave(&host->lock, flags);
-
- WARN_ON(host->mrq != NULL);
-@@ -1731,14 +1745,12 @@ static void bcm2835_sdhost_set_ios(struc
-
- bcm2835_sdhost_write(host, host->hcfg, SDHCFG);
-
-- if (!ios->clock || ios->clock != host->clock) {
-- bcm2835_sdhost_set_clock(host, ios->clock);
-- host->clock = ios->clock;
-- }
--
- mmiowb();
-
- spin_unlock_irqrestore(&host->lock, flags);
-+
-+ if (!ios->clock || ios->clock != host->clock)
-+ bcm2835_sdhost_set_clock(host, ios->clock);
- }
-
- static struct mmc_host_ops bcm2835_sdhost_ops = {
-@@ -1810,7 +1822,7 @@ static void bcm2835_sdhost_tasklet_finis
- host->overclock_50--;
- pr_warn("%s: reducing overclock due to errors\n",
- mmc_hostname(host->mmc));
-- bcm2835_sdhost_set_clock(host,50*MHZ);
-+ host->reset_clock = 1;
- mrq->cmd->error = -EILSEQ;
- mrq->cmd->retries = 1;
- }
-@@ -1979,7 +1991,6 @@ static int bcm2835_sdhost_probe(struct p
- mmc->ops = &bcm2835_sdhost_ops;
- host = mmc_priv(mmc);
- host->mmc = mmc;
-- host->cmd_quick_poll_retries = 0;
- host->pio_timeout = msecs_to_jiffies(500);
- host->pio_limit = 1;
- host->max_delay = 1; /* Warn if over 1ms */
diff --git a/target/linux/brcm2708/patches-4.4/0235-config-Enable-CONFIG_IPV6_ROUTER_PREF-for-networks-w.patch b/target/linux/brcm2708/patches-4.4/0235-config-Enable-CONFIG_IPV6_ROUTER_PREF-for-networks-w.patch
deleted file mode 100644
index 4a10591..0000000
--- a/target/linux/brcm2708/patches-4.4/0235-config-Enable-CONFIG_IPV6_ROUTER_PREF-for-networks-w.patch
+++ /dev/null
@@ -1,31 +0,0 @@
-From c11caeae93f2aa630f949425a81443dbf5da3a3c Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Thu, 7 Apr 2016 12:44:24 +0100
-Subject: [PATCH] config: Enable CONFIG_IPV6_ROUTER_PREF for networks with
- multiple routers
-
----
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 2 files changed, 2 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -101,6 +101,7 @@ CONFIG_INET_XFRM_MODE_TUNNEL=m
- CONFIG_INET_XFRM_MODE_BEET=m
- CONFIG_INET_LRO=m
- CONFIG_INET_DIAG=m
-+CONFIG_IPV6_ROUTER_PREF=y
- CONFIG_INET6_AH=m
- CONFIG_INET6_ESP=m
- CONFIG_INET6_IPCOMP=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -95,6 +95,7 @@ CONFIG_INET_XFRM_MODE_TUNNEL=m
- CONFIG_INET_XFRM_MODE_BEET=m
- CONFIG_INET_LRO=m
- CONFIG_INET_DIAG=m
-+CONFIG_IPV6_ROUTER_PREF=y
- CONFIG_INET6_AH=m
- CONFIG_INET6_ESP=m
- CONFIG_INET6_IPCOMP=m
diff --git a/target/linux/brcm2708/patches-4.4/0236-Enable-hid-betopff-module.patch b/target/linux/brcm2708/patches-4.4/0236-Enable-hid-betopff-module.patch
deleted file mode 100644
index 6e0fc1e..0000000
--- a/target/linux/brcm2708/patches-4.4/0236-Enable-hid-betopff-module.patch
+++ /dev/null
@@ -1,32 +0,0 @@
-From 828cd1ba4537fafed9f22945c2c867bbdd403052 Mon Sep 17 00:00:00 2001
-From: jochenberger <fooberger at gmail.com>
-Date: Thu, 7 Apr 2016 21:38:46 +0200
-Subject: [PATCH] Enable hid-betopff module
-
-Add force feedback support for Betop based devices
-https://github.com/raspberrypi/linux/blob/rpi-4.1.y/drivers/hid/hid-betopff.c
----
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 2 files changed, 2 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -867,6 +867,7 @@ CONFIG_HID_A4TECH=m
- CONFIG_HID_ACRUX=m
- CONFIG_HID_APPLE=m
- CONFIG_HID_BELKIN=m
-+CONFIG_HID_BETOP_FF=m
- CONFIG_HID_CHERRY=m
- CONFIG_HID_CHICONY=m
- CONFIG_HID_CYPRESS=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -859,6 +859,7 @@ CONFIG_HID_A4TECH=m
- CONFIG_HID_ACRUX=m
- CONFIG_HID_APPLE=m
- CONFIG_HID_BELKIN=m
-+CONFIG_HID_BETOP_FF=m
- CONFIG_HID_CHERRY=m
- CONFIG_HID_CHICONY=m
- CONFIG_HID_CYPRESS=m
diff --git a/target/linux/brcm2708/patches-4.4/0237-config-Make-IPV6-a-module-and-regenerate-with-defcon.patch b/target/linux/brcm2708/patches-4.4/0237-config-Make-IPV6-a-module-and-regenerate-with-defcon.patch
deleted file mode 100644
index ea0ce74..0000000
--- a/target/linux/brcm2708/patches-4.4/0237-config-Make-IPV6-a-module-and-regenerate-with-defcon.patch
+++ /dev/null
@@ -1,69 +0,0 @@
-From 395609f56e3d714f92a0902760ff9fccb5ed5701 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Tue, 12 Apr 2016 12:45:16 +0100
-Subject: [PATCH] config: Make IPV6 a module and regenerate with defconfig
-
----
- arch/arm/configs/bcm2709_defconfig | 4 ++--
- arch/arm/configs/bcmrpi_defconfig | 6 +++---
- 2 files changed, 5 insertions(+), 5 deletions(-)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -101,6 +101,7 @@ CONFIG_INET_XFRM_MODE_TUNNEL=m
- CONFIG_INET_XFRM_MODE_BEET=m
- CONFIG_INET_LRO=m
- CONFIG_INET_DIAG=m
-+CONFIG_IPV6=m
- CONFIG_IPV6_ROUTER_PREF=y
- CONFIG_INET6_AH=m
- CONFIG_INET6_ESP=m
-@@ -600,10 +601,9 @@ CONFIG_HW_RANDOM=y
- CONFIG_RAW_DRIVER=y
- CONFIG_I2C=y
- CONFIG_I2C_CHARDEV=m
-+CONFIG_I2C_MUX_PCA954x=m
- CONFIG_I2C_BCM2708=m
- CONFIG_I2C_GPIO=m
--CONFIG_I2C_MUX=m
--CONFIG_I2C_MUX_PCA954x=m
- CONFIG_SPI=y
- CONFIG_SPI_BCM2835=m
- CONFIG_SPI_BCM2835AUX=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -73,7 +73,6 @@ CONFIG_INET=y
- CONFIG_IP_MULTICAST=y
- CONFIG_IP_ADVANCED_ROUTER=y
- CONFIG_IP_MULTIPLE_TABLES=y
--CONFIG_IPV6_SUBTREES=y
- CONFIG_IP_ROUTE_MULTIPATH=y
- CONFIG_IP_ROUTE_VERBOSE=y
- CONFIG_IP_PNP=y
-@@ -95,12 +94,14 @@ CONFIG_INET_XFRM_MODE_TUNNEL=m
- CONFIG_INET_XFRM_MODE_BEET=m
- CONFIG_INET_LRO=m
- CONFIG_INET_DIAG=m
-+CONFIG_IPV6=m
- CONFIG_IPV6_ROUTER_PREF=y
- CONFIG_INET6_AH=m
- CONFIG_INET6_ESP=m
- CONFIG_INET6_IPCOMP=m
- CONFIG_IPV6_TUNNEL=m
- CONFIG_IPV6_MULTIPLE_TABLES=y
-+CONFIG_IPV6_SUBTREES=y
- CONFIG_IPV6_MROUTE=y
- CONFIG_IPV6_MROUTE_MULTIPLE_TABLES=y
- CONFIG_IPV6_PIMSM_V2=y
-@@ -593,10 +594,9 @@ CONFIG_HW_RANDOM=y
- CONFIG_RAW_DRIVER=y
- CONFIG_I2C=y
- CONFIG_I2C_CHARDEV=m
-+CONFIG_I2C_MUX_PCA954x=m
- CONFIG_I2C_BCM2708=m
- CONFIG_I2C_GPIO=m
--CONFIG_I2C_MUX=m
--CONFIG_I2C_MUX_PCA954x=m
- CONFIG_SPI=y
- CONFIG_SPI_BCM2835=m
- CONFIG_SPI_BCM2835AUX=m
diff --git a/target/linux/brcm2708/patches-4.4/0238-BCM270X_DT-Add-dpi24-overlay.patch b/target/linux/brcm2708/patches-4.4/0238-BCM270X_DT-Add-dpi24-overlay.patch
deleted file mode 100644
index 1c77984..0000000
--- a/target/linux/brcm2708/patches-4.4/0238-BCM270X_DT-Add-dpi24-overlay.patch
+++ /dev/null
@@ -1,74 +0,0 @@
-From d2d72085169d260835028620d0ca430c34b73bac Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Tue, 5 Apr 2016 13:01:54 +0100
-Subject: [PATCH] BCM270X_DT: Add dpi24 overlay
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 8 +++++++
- arch/arm/boot/dts/overlays/dpi24-overlay.dts | 31 ++++++++++++++++++++++++++++
- 3 files changed, 40 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/dpi24-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -15,6 +15,7 @@ endif
- dtbo-$(RPI_DT_OVERLAYS) += ads7846.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += at86rf233.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += bmp085_i2c-sensor.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += dpi24.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += dwc2.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += dwc-otg.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += dht11.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -213,6 +213,14 @@ Params: gpiopin GPIO con
- (default 4)
-
-
-+Name: dpi24
-+Info: Overlay for a generic 24-bit DPI display
-+ This uses GPIOs 0-27 (so no I2C, uart etc.), and activates the output
-+ 2-3 seconds after the kernel has started.
-+Load: dtoverlay=dpi24
-+Params: <None>
-+
-+
- Name: dwc-otg
- Info: Selects the dwc_otg USB controller driver which has fiq support. This
- is the default on all except the Pi Zero which defaults to dwc2.
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/dpi24-overlay.dts
-@@ -0,0 +1,31 @@
-+/dts-v1/;
-+/plugin/;
-+
-+/{
-+ compatible = "brcm,bcm2708";
-+
-+ // There is no DPI driver module, but we need a platform device
-+ // node (that doesn't already use pinctrl) to hang the pinctrl
-+ // reference on - leds will do
-+
-+ fragment at 0 {
-+ target = <&leds>;
-+ __overlay__ {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&dpi24_pins>;
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ dpi24_pins: dpi24_pins {
-+ brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11
-+ 12 13 14 15 16 17 18 19 20
-+ 21 22 23 24 25 26 27>;
-+ brcm,function = <6>; /* alt2 */
-+ brcm,pull = <0>; /* no pull */
-+ };
-+ };
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0239-Modify-IQAudIO-DAC-ASoC-driver-to-set-card-dai-confi.patch b/target/linux/brcm2708/patches-4.4/0239-Modify-IQAudIO-DAC-ASoC-driver-to-set-card-dai-confi.patch
deleted file mode 100644
index cc50105..0000000
--- a/target/linux/brcm2708/patches-4.4/0239-Modify-IQAudIO-DAC-ASoC-driver-to-set-card-dai-confi.patch
+++ /dev/null
@@ -1,57 +0,0 @@
-From 3e4b46800c9574ad64f4e5fb8836b702f7d590a7 Mon Sep 17 00:00:00 2001
-From: DigitalDreamtime <clive.messer at digitaldreamtime.co.uk>
-Date: Thu, 14 Apr 2016 00:57:33 +0100
-Subject: [PATCH] Modify IQAudIO DAC+ ASoC driver to set card/dai config from
- dt
-
-Add the ability to set the card name, dai name and dai stream name, from
-dt config.
-
-Signed-off-by: DigitalDreamtime <clive.messer at digitaldreamtime.co.uk>
----
- sound/soc/bcm/iqaudio-dac.c | 13 ++++++++++---
- 1 file changed, 10 insertions(+), 3 deletions(-)
-
---- a/sound/soc/bcm/iqaudio-dac.c
-+++ b/sound/soc/bcm/iqaudio-dac.c
-@@ -61,8 +61,6 @@ static struct snd_soc_ops snd_rpi_iqaudi
-
- static struct snd_soc_dai_link snd_rpi_iqaudio_dac_dai[] = {
- {
-- .name = "IQaudIO DAC",
-- .stream_name = "IQaudIO DAC HiFi",
- .cpu_dai_name = "bcm2708-i2s.0",
- .codec_dai_name = "pcm512x-hifi",
- .platform_name = "bcm2708-i2s.0",
-@@ -76,7 +74,6 @@ static struct snd_soc_dai_link snd_rpi_i
-
- /* audio machine driver */
- static struct snd_soc_card snd_rpi_iqaudio_dac = {
-- .name = "IQaudIODAC",
- .owner = THIS_MODULE,
- .dai_link = snd_rpi_iqaudio_dac_dai,
- .num_links = ARRAY_SIZE(snd_rpi_iqaudio_dac_dai),
-@@ -90,6 +87,7 @@ static int snd_rpi_iqaudio_dac_probe(str
-
- if (pdev->dev.of_node) {
- struct device_node *i2s_node;
-+ struct snd_soc_card *card = &snd_rpi_iqaudio_dac;
- struct snd_soc_dai_link *dai = &snd_rpi_iqaudio_dac_dai[0];
- i2s_node = of_parse_phandle(pdev->dev.of_node,
- "i2s-controller", 0);
-@@ -103,6 +101,15 @@ static int snd_rpi_iqaudio_dac_probe(str
-
- digital_gain_0db_limit = !of_property_read_bool(pdev->dev.of_node,
- "iqaudio,24db_digital_gain");
-+ if (of_property_read_string(pdev->dev.of_node, "card_name",
-+ &card->name))
-+ card->name = "IQaudIODAC";
-+ if (of_property_read_string(pdev->dev.of_node, "dai_name",
-+ &dai->name))
-+ dai->name = "IQaudIO DAC";
-+ if (of_property_read_string(pdev->dev.of_node, "dai_stream_name",
-+ &dai->stream_name))
-+ dai->stream_name = "IQaudIO DAC HiFi";
- }
-
- ret = snd_soc_register_card(&snd_rpi_iqaudio_dac);
diff --git a/target/linux/brcm2708/patches-4.4/0240-Add-support-for-the-Digital-Dreamtime-Akkordion-musi.patch b/target/linux/brcm2708/patches-4.4/0240-Add-support-for-the-Digital-Dreamtime-Akkordion-musi.patch
deleted file mode 100644
index 84d7d18..0000000
--- a/target/linux/brcm2708/patches-4.4/0240-Add-support-for-the-Digital-Dreamtime-Akkordion-musi.patch
+++ /dev/null
@@ -1,104 +0,0 @@
-From 6b4abb74e8855962e6826d5cb86bdd6557eb54ad Mon Sep 17 00:00:00 2001
-From: DigitalDreamtime <clive.messer at digitaldreamtime.co.uk>
-Date: Thu, 14 Apr 2016 01:00:58 +0100
-Subject: [PATCH] Add support for the Digital Dreamtime Akkordion music player.
-
-Support the Digital Dreamtime Akkordion using the OEM IQAudIO DAC+ or
-DACZero modules. Set ALSA card name, ("Akkordion"), from dt config.
-
-Signed-off-by: DigitalDreamtime <clive.messer at digitaldreamtime.co.uk>
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 20 ++++++++++
- .../dts/overlays/akkordion-iqdacplus-overlay.dts | 46 ++++++++++++++++++++++
- 3 files changed, 67 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/akkordion-iqdacplus-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -13,6 +13,7 @@ ifeq ($(CONFIG_ARCH_BCM2835),y)
- endif
-
- dtbo-$(RPI_DT_OVERLAYS) += ads7846.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += akkordion-iqdacplus.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += at86rf233.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += bmp085_i2c-sensor.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += dpi24.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -186,6 +186,26 @@ Params: cs SPI bus
- www.kernel.org/doc/Documentation/devicetree/bindings/input/ads7846.txt
-
-
-+Name: akkordion-iqdacplus
-+Info: Configures the Digital Dreamtime Akkordion Music Player (based on the
-+ OEM IQAudIO DAC+ or DAC Zero module).
-+Load: dtoverlay=akkordion-iqdacplus,<param>=<val>
-+Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec
-+ Digital volume control. Enable with
-+ dtoverlay=akkordion-iqdacplus,24db_digital_gain
-+ (The default behaviour is that the Digital
-+ volume control is limited to a maximum of
-+ 0dB. ie. it can attenuate but not provide
-+ gain. For most users, this will be desired
-+ as it will prevent clipping. By appending
-+ the 24db_digital_gain parameter, the Digital
-+ volume control will allow up to 24dB of
-+ gain. If this parameter is enabled, it is the
-+ responsibility of the user to ensure that
-+ the Digital volume control is set to a value
-+ that does not result in clipping/distortion!)
-+
-+
- Name: at86rf233
- Info: Configures the Atmel AT86RF233 802.15.4 low-power WPAN transceiver,
- connected to spi0.0
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/akkordion-iqdacplus-overlay.dts
-@@ -0,0 +1,46 @@
-+// Definitions for Digital Dreamtime Akkordion using IQaudIO DAC+ or DACZero
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&sound>;
-+ frag0: __overlay__ {
-+ compatible = "iqaudio,iqaudio-dac";
-+ card_name = "Akkordion";
-+ dai_name = "IQaudIO DAC";
-+ dai_stream_name = "IQaudIO DAC HiFi";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&i2s>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&i2c1>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ pcm5122 at 4c {
-+ #sound-dai-cells = <0>;
-+ compatible = "ti,pcm5122";
-+ reg = <0x4c>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ 24db_digital_gain = <&frag0>,"iqaudio,24db_digital_gain?";
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0241-Add-Support-for-BoomBerry-Audio-boards.patch b/target/linux/brcm2708/patches-4.4/0241-Add-Support-for-BoomBerry-Audio-boards.patch
deleted file mode 100644
index 5e16440..0000000
--- a/target/linux/brcm2708/patches-4.4/0241-Add-Support-for-BoomBerry-Audio-boards.patch
+++ /dev/null
@@ -1,605 +0,0 @@
-From 4d6aaca0231c13aa5b47284cc58d0796196c0ee5 Mon Sep 17 00:00:00 2001
-From: Aaron Shaw <shawaj at gmail.com>
-Date: Thu, 7 Apr 2016 21:26:21 +0100
-Subject: [PATCH] Add Support for BoomBerry Audio boards
-
----
- arch/arm/boot/dts/overlays/Makefile | 2 +
- arch/arm/boot/dts/overlays/README | 26 +++
- .../boot/dts/overlays/boomberry-dac-overlay.dts | 43 +++++
- .../boot/dts/overlays/boomberry-digi-overlay.dts | 39 ++++
- arch/arm/configs/bcm2709_defconfig | 2 +
- arch/arm/configs/bcmrpi_defconfig | 2 +
- sound/soc/bcm/Kconfig | 14 ++
- sound/soc/bcm/Makefile | 4 +
- sound/soc/bcm/boomberry-dac.c | 163 ++++++++++++++++
- sound/soc/bcm/boomberry-digi.c | 215 +++++++++++++++++++++
- 10 files changed, 510 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/boomberry-dac-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/boomberry-digi-overlay.dts
- create mode 100644 sound/soc/bcm/boomberry-dac.c
- create mode 100644 sound/soc/bcm/boomberry-digi.c
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -16,6 +16,8 @@ dtbo-$(RPI_DT_OVERLAYS) += ads7846.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += akkordion-iqdacplus.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += at86rf233.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += bmp085_i2c-sensor.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += boomberry-dac.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += boomberry-digi.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += dpi24.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += dwc2.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += dwc-otg.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -225,6 +225,32 @@ Load: dtoverlay=bmp085_i2c-sensor
- Params: <None>
-
-
-+Name: boomberry-dac
-+Info: Configures the BoomBerry DAC HAT, Amp HAT, DAC Zero and Amp Zero audio
-+ cards
-+Load: dtoverlay=boomberry-dac,<param>=<val>
-+Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec
-+ Digital volume control. Enable with
-+ "dtoverlay=boomberry-dac,24db_digital_gain"
-+ (The default behaviour is that the Digital
-+ volume control is limited to a maximum of
-+ 0dB. ie. it can attenuate but not provide
-+ gain. For most users, this will be desired
-+ as it will prevent clipping. By appending
-+ the 24dB_digital_gain parameter, the Digital
-+ volume control will allow up to 24dB of
-+ gain. If this parameter is enabled, it is the
-+ responsibility of the user to ensure that
-+ the Digital volume control is set to a value
-+ that does not result in clipping/distortion!)
-+
-+
-+Name: boomberry-digi
-+Info: Configures the BoomBerry Digi HAT and Digi Zero audio cards
-+Load: dtoverlay=boomberry-digi
-+Params: <None>
-+
-+
- Name: dht11
- Info: Overlay for the DHT11/DHT21/DHT22 humidity/temperature sensors
- Also sometimes found with the part number(s) AM230x.
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/boomberry-dac-overlay.dts
-@@ -0,0 +1,43 @@
-+// Definitions for BoomBerry DAC
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&sound>;
-+ frag0: __overlay__ {
-+ compatible = "boomberry,boomberry-dac";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&i2s>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&i2c1>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ pcm5122 at 4d {
-+ #sound-dai-cells = <0>;
-+ compatible = "ti,pcm5122";
-+ reg = <0x4d>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ 24db_digital_gain = <&frag0>,"boomberry,24db_digital_gain?";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/boomberry-digi-overlay.dts
-@@ -0,0 +1,39 @@
-+// Definitions for BoomBerry Digi
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&sound>;
-+ __overlay__ {
-+ compatible = "boomberry,boomberry-digi";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&i2s>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&i2c1>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ wm8804 at 3b {
-+ #sound-dai-cells = <0>;
-+ compatible = "wlf,wm8804";
-+ reg = <0x3b>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+};
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -853,6 +853,8 @@ CONFIG_SND_BCM2708_SOC_HIFIBERRY_DAC=m
- CONFIG_SND_BCM2708_SOC_HIFIBERRY_DACPLUS=m
- CONFIG_SND_BCM2708_SOC_HIFIBERRY_DIGI=m
- CONFIG_SND_BCM2708_SOC_HIFIBERRY_AMP=m
-+CONFIG_SND_BCM2708_SOC_BOOMBERRY_DAC=m
-+CONFIG_SNG_BCM2708_SOC_BOOMBERRY_DIGI=m
- CONFIG_SND_BCM2708_SOC_RPI_DAC=m
- CONFIG_SND_BCM2708_SOC_RPI_PROTO=m
- CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -845,6 +845,8 @@ CONFIG_SND_BCM2708_SOC_HIFIBERRY_DAC=m
- CONFIG_SND_BCM2708_SOC_HIFIBERRY_DACPLUS=m
- CONFIG_SND_BCM2708_SOC_HIFIBERRY_DIGI=m
- CONFIG_SND_BCM2708_SOC_HIFIBERRY_AMP=m
-+CONFIG_SND_BCM2708_SOC_BOOMBERRY_DAC=m
-+CONFIG_SND_BCM2708_SOC_BOOMBERRY_DIGI=m
- CONFIG_SND_BCM2708_SOC_RPI_DAC=m
- CONFIG_SND_BCM2708_SOC_RPI_PROTO=m
- CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC=m
---- a/sound/soc/bcm/Kconfig
-+++ b/sound/soc/bcm/Kconfig
-@@ -50,6 +50,20 @@ config SND_BCM2708_SOC_RPI_PROTO
- help
- Say Y or M if you want to add support for Audio Codec Board PROTO (WM8731).
-
-+config SND_BCM2708_SOC_BOOMBERRY_DAC
-+ tristate "Support for BoomBerry DAC"
-+ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
-+ select SND_SOC_PCM512x
-+ help
-+ Say Y or M if you want to add support for BoomBerry DAC.
-+
-+config SND_BCM2708_SOC_BOOMBERRY_DIGI
-+ tristate "Support for BoomBerry Digi"
-+ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
-+ select SND_SOC_WM8804
-+ help
-+ Say Y or M if you want to add support for BoomBerry Digi.
-+
- config SND_BCM2708_SOC_IQAUDIO_DAC
- tristate "Support for IQaudIO-DAC"
- depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
---- a/sound/soc/bcm/Makefile
-+++ b/sound/soc/bcm/Makefile
-@@ -8,6 +8,8 @@ snd-soc-hifiberry-dac-objs := hifiberry_
- snd-soc-hifiberry-dacplus-objs := hifiberry_dacplus.o
- snd-soc-hifiberry-digi-objs := hifiberry_digi.o
- snd-soc-hifiberry-amp-objs := hifiberry_amp.o
-+snd-soc-boomberry-dac-objs := boomberry-dac.o
-+snd-soc-boomberry-digi-objs := boomberry-digi.o
- snd-soc-rpi-dac-objs := rpi-dac.o
- snd-soc-rpi-proto-objs := rpi-proto.o
- snd-soc-iqaudio-dac-objs := iqaudio-dac.o
-@@ -17,6 +19,8 @@ obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_D
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DACPLUS) += snd-soc-hifiberry-dacplus.o
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DIGI) += snd-soc-hifiberry-digi.o
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_AMP) += snd-soc-hifiberry-amp.o
-+obj-$(CONFIG_SND_BCM2708_SOC_BOOMBERRY_DAC) += snd-soc-boomberry-dac.o
-+obj-$(CONFIG_SND_BCM2708_SOC_BOOMBERRY_DIGI) += snd-soc-boomberry-digi.o
- obj-$(CONFIG_SND_BCM2708_SOC_RPI_DAC) += snd-soc-rpi-dac.o
- obj-$(CONFIG_SND_BCM2708_SOC_RPI_PROTO) += snd-soc-rpi-proto.o
- obj-$(CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC) += snd-soc-iqaudio-dac.o
---- /dev/null
-+++ b/sound/soc/bcm/boomberry-dac.c
-@@ -0,0 +1,163 @@
-+/*
-+ * ASoC Driver for BoomBerry DAC Raspberry Pi HAT Sound Card
-+ *
-+ * Author: Milan Neskovic
-+ * Copyright 2016
-+ * based on code by Daniel Matuschek <info at crazy-audio.com>
-+ * based on code by Florian Meier <florian.meier at koalo.de>
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * version 2 as published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful, but
-+ * WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
-+ * General Public License for more details.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+
-+#include <sound/core.h>
-+#include <sound/pcm.h>
-+#include <sound/pcm_params.h>
-+#include <sound/soc.h>
-+#include <sound/jack.h>
-+
-+#include "../codecs/pcm512x.h"
-+
-+static bool digital_gain_0db_limit = true;
-+
-+static int snd_rpi_boomberry_dac_init(struct snd_soc_pcm_runtime *rtd)
-+{
-+ struct snd_soc_codec *codec = rtd->codec;
-+ snd_soc_update_bits(codec, PCM512x_GPIO_EN, 0x08, 0x08);
-+ snd_soc_update_bits(codec, PCM512x_GPIO_OUTPUT_4, 0xf, 0x02);
-+ snd_soc_update_bits(codec, PCM512x_GPIO_CONTROL_1, 0x08,0x08);
-+
-+ if (digital_gain_0db_limit)
-+ {
-+ int ret;
-+ struct snd_soc_card *card = rtd->card;
-+ struct snd_soc_codec *codec = rtd->codec;
-+
-+ ret = snd_soc_limit_volume(codec, "Digital Playback Volume", 207);
-+ if (ret < 0)
-+ dev_warn(card->dev, "Failed to set volume limit: %d\n", ret);
-+ }
-+
-+ return 0;
-+}
-+
-+static int snd_rpi_boomberry_dac_hw_params(struct snd_pcm_substream *substream,
-+ struct snd_pcm_hw_params *params)
-+{
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
-+ /*return snd_soc_dai_set_bclk_ratio(cpu_dai, 64);*/
-+ unsigned int sample_bits =
-+ snd_pcm_format_physical_width(params_format(params));
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, sample_bits * 2);
-+}
-+
-+static int snd_rpi_boomberry_dac_startup(struct snd_pcm_substream *substream) {
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_codec *codec = rtd->codec;
-+ snd_soc_update_bits(codec, PCM512x_GPIO_CONTROL_1, 0x08,0x08);
-+ return 0;
-+}
-+
-+static void snd_rpi_boomberry_dac_shutdown(struct snd_pcm_substream *substream) {
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_codec *codec = rtd->codec;
-+ snd_soc_update_bits(codec, PCM512x_GPIO_CONTROL_1, 0x08,0x00);
-+}
-+
-+/* machine stream operations */
-+static struct snd_soc_ops snd_rpi_boomberry_dac_ops = {
-+ .hw_params = snd_rpi_boomberry_dac_hw_params,
-+ .startup = snd_rpi_boomberry_dac_startup,
-+ .shutdown = snd_rpi_boomberry_dac_shutdown,
-+};
-+
-+static struct snd_soc_dai_link snd_rpi_boomberry_dac_dai[] = {
-+{
-+ .name = "BoomBerry DAC",
-+ .stream_name = "BoomBerry DAC HiFi",
-+ .cpu_dai_name = "bcm2708-i2s.0",
-+ .codec_dai_name = "pcm512x-hifi",
-+ .platform_name = "bcm2708-i2s.0",
-+ .codec_name = "pcm512x.1-004d",
-+ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF |
-+ SND_SOC_DAIFMT_CBS_CFS,
-+ .ops = &snd_rpi_boomberry_dac_ops,
-+ .init = snd_rpi_boomberry_dac_init,
-+},
-+};
-+
-+/* audio machine driver */
-+static struct snd_soc_card snd_rpi_boomberry_dac = {
-+ .name = "snd_rpi_boomberry_dac",
-+ .owner = THIS_MODULE,
-+ .dai_link = snd_rpi_boomberry_dac_dai,
-+ .num_links = ARRAY_SIZE(snd_rpi_boomberry_dac_dai),
-+};
-+
-+static int snd_rpi_boomberry_dac_probe(struct platform_device *pdev)
-+{
-+ int ret = 0;
-+
-+ snd_rpi_boomberry_dac.dev = &pdev->dev;
-+
-+ if (pdev->dev.of_node) {
-+ struct device_node *i2s_node;
-+ struct snd_soc_dai_link *dai = &snd_rpi_boomberry_dac_dai[0];
-+ i2s_node = of_parse_phandle(pdev->dev.of_node,
-+ "i2s-controller", 0);
-+
-+ if (i2s_node) {
-+ dai->cpu_dai_name = NULL;
-+ dai->cpu_of_node = i2s_node;
-+ dai->platform_name = NULL;
-+ dai->platform_of_node = i2s_node;
-+ }
-+
-+ digital_gain_0db_limit = !of_property_read_bool(
-+ pdev->dev.of_node, "boomberry,24db_digital_gain");
-+ }
-+
-+ ret = snd_soc_register_card(&snd_rpi_boomberry_dac);
-+ if (ret)
-+ dev_err(&pdev->dev,
-+ "snd_soc_register_card() failed: %d\n", ret);
-+
-+ return ret;
-+}
-+
-+static int snd_rpi_boomberry_dac_remove(struct platform_device *pdev)
-+{
-+ return snd_soc_unregister_card(&snd_rpi_boomberry_dac);
-+}
-+
-+static const struct of_device_id snd_rpi_boomberry_dac_of_match[] = {
-+ { .compatible = "boomberry,boomberry-dac", },
-+ {},
-+};
-+MODULE_DEVICE_TABLE(of, snd_rpi_boomberry_dac_of_match);
-+
-+static struct platform_driver snd_rpi_boomberry_dac_driver = {
-+ .driver = {
-+ .name = "snd-rpi-boomberry-dac",
-+ .owner = THIS_MODULE,
-+ .of_match_table = snd_rpi_boomberry_dac_of_match,
-+ },
-+ .probe = snd_rpi_boomberry_dac_probe,
-+ .remove = snd_rpi_boomberry_dac_remove,
-+};
-+
-+module_platform_driver(snd_rpi_boomberry_dac_driver);
-+
-+MODULE_AUTHOR("Milan Neskovic <info at boomberry.co>");
-+MODULE_DESCRIPTION("ASoC Driver for BoomBerry PI DAC HAT Sound Card");
-+MODULE_LICENSE("GPL v2");
---- /dev/null
-+++ b/sound/soc/bcm/boomberry-digi.c
-@@ -0,0 +1,215 @@
-+/*
-+ * ASoC Driver for BoomBerry Raspberry Pi Digi HAT Sound Card
-+ *
-+ * Author: Milan Neskovic
-+ * Copyright 2016
-+ * based on code by Daniel Matuschek <info at crazy-audio.com>
-+ * based on code by Florian Meier <florian.meier at koalo.de>
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * version 2 as published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful, but
-+ * WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
-+ * General Public License for more details.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+
-+#include <sound/core.h>
-+#include <sound/pcm.h>
-+#include <sound/pcm_params.h>
-+#include <sound/soc.h>
-+#include <sound/jack.h>
-+
-+#include "../codecs/wm8804.h"
-+
-+static int snd_rpi_boomberry_digi_init(struct snd_soc_pcm_runtime *rtd)
-+{
-+ struct snd_soc_codec *codec = rtd->codec;
-+
-+ /* enable TX output */
-+ snd_soc_update_bits(codec, WM8804_PWRDN, 0x4, 0x0);
-+
-+ return 0;
-+}
-+
-+static int snd_rpi_boomberry_digi_startup(struct snd_pcm_substream *substream) {
-+ /* turn on digital output */
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_codec *codec = rtd->codec;
-+ snd_soc_update_bits(codec, WM8804_PWRDN, 0x3c, 0x00);
-+ return 0;
-+}
-+
-+static void snd_rpi_boomberry_digi_shutdown(struct snd_pcm_substream *substream) {
-+ /* turn off output */
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_codec *codec = rtd->codec;
-+ snd_soc_update_bits(codec, WM8804_PWRDN, 0x3c, 0x3c);
-+}
-+
-+static int snd_rpi_boomberry_digi_hw_params(struct snd_pcm_substream *substream,
-+ struct snd_pcm_hw_params *params)
-+{
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_dai *codec_dai = rtd->codec_dai;
-+ struct snd_soc_codec *codec = rtd->codec;
-+ struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
-+
-+ int sysclk = 27000000; /* This is fixed on this board */
-+
-+ long mclk_freq=0;
-+ int mclk_div=1;
-+ int sampling_freq=1;
-+
-+ int ret;
-+
-+ int samplerate = params_rate(params);
-+
-+ if (samplerate<=96000) {
-+ mclk_freq=samplerate*256;
-+ mclk_div=WM8804_MCLKDIV_256FS;
-+ } else {
-+ mclk_freq=samplerate*128;
-+ mclk_div=WM8804_MCLKDIV_128FS;
-+ }
-+
-+ switch (samplerate) {
-+ case 32000:
-+ sampling_freq=0x03;
-+ break;
-+ case 44100:
-+ sampling_freq=0x00;
-+ break;
-+ case 48000:
-+ sampling_freq=0x02;
-+ break;
-+ case 88200:
-+ sampling_freq=0x08;
-+ break;
-+ case 96000:
-+ sampling_freq=0x0a;
-+ break;
-+ case 176400:
-+ sampling_freq=0x0c;
-+ break;
-+ case 192000:
-+ sampling_freq=0x0e;
-+ break;
-+ default:
-+ dev_err(codec->dev,
-+ "Failed to set WM8804 SYSCLK, unsupported samplerate %d\n",
-+ samplerate);
-+ }
-+
-+ snd_soc_dai_set_clkdiv(codec_dai, WM8804_MCLK_DIV, mclk_div);
-+ snd_soc_dai_set_pll(codec_dai, 0, 0, sysclk, mclk_freq);
-+
-+ ret = snd_soc_dai_set_sysclk(codec_dai, WM8804_TX_CLKSRC_PLL,
-+ sysclk, SND_SOC_CLOCK_OUT);
-+ if (ret < 0) {
-+ dev_err(codec->dev,
-+ "Failed to set WM8804 SYSCLK: %d\n", ret);
-+ return ret;
-+ }
-+
-+ /* Enable TX output */
-+ snd_soc_update_bits(codec, WM8804_PWRDN, 0x4, 0x0);
-+
-+ /* Power on */
-+ snd_soc_update_bits(codec, WM8804_PWRDN, 0x9, 0);
-+
-+ /* set sampling frequency status bits */
-+ snd_soc_update_bits(codec, WM8804_SPDTX4, 0x0f, sampling_freq);
-+
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai,64);
-+}
-+
-+/* machine stream operations */
-+static struct snd_soc_ops snd_rpi_boomberry_digi_ops = {
-+ .hw_params = snd_rpi_boomberry_digi_hw_params,
-+ .startup = snd_rpi_boomberry_digi_startup,
-+ .shutdown = snd_rpi_boomberry_digi_shutdown,
-+};
-+
-+static struct snd_soc_dai_link snd_rpi_boomberry_digi_dai[] = {
-+{
-+ .name = "BoomBerry Digi",
-+ .stream_name = "BoomBerry Digi HiFi",
-+ .cpu_dai_name = "bcm2708-i2s.0",
-+ .codec_dai_name = "wm8804-spdif",
-+ .platform_name = "bcm2708-i2s.0",
-+ .codec_name = "wm8804.1-003b",
-+ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF |
-+ SND_SOC_DAIFMT_CBM_CFM,
-+ .ops = &snd_rpi_boomberry_digi_ops,
-+ .init = snd_rpi_boomberry_digi_init,
-+},
-+};
-+
-+/* audio machine driver */
-+static struct snd_soc_card snd_rpi_boomberry_digi = {
-+ .name = "snd_rpi_boomberry_digi",
-+ .owner = THIS_MODULE,
-+ .dai_link = snd_rpi_boomberry_digi_dai,
-+ .num_links = ARRAY_SIZE(snd_rpi_boomberry_digi_dai),
-+};
-+
-+static int snd_rpi_boomberry_digi_probe(struct platform_device *pdev)
-+{
-+ int ret = 0;
-+
-+ snd_rpi_boomberry_digi.dev = &pdev->dev;
-+
-+ if (pdev->dev.of_node) {
-+ struct device_node *i2s_node;
-+ struct snd_soc_dai_link *dai = &snd_rpi_boomberry_digi_dai[0];
-+ i2s_node = of_parse_phandle(pdev->dev.of_node,
-+ "i2s-controller", 0);
-+
-+ if (i2s_node) {
-+ dai->cpu_dai_name = NULL;
-+ dai->cpu_of_node = i2s_node;
-+ dai->platform_name = NULL;
-+ dai->platform_of_node = i2s_node;
-+ }
-+ }
-+
-+ ret = snd_soc_register_card(&snd_rpi_boomberry_digi);
-+ if (ret)
-+ dev_err(&pdev->dev,
-+ "snd_soc_register_card() failed: %d\n", ret);
-+
-+ return ret;
-+}
-+
-+static int snd_rpi_boomberry_digi_remove(struct platform_device *pdev)
-+{
-+ return snd_soc_unregister_card(&snd_rpi_boomberry_digi);
-+}
-+
-+static const struct of_device_id snd_rpi_boomberry_digi_of_match[] = {
-+ { .compatible = "boomberry,boomberry-digi", },
-+ {},
-+};
-+MODULE_DEVICE_TABLE(of, snd_rpi_boomberry_digi_of_match);
-+
-+static struct platform_driver snd_rpi_boomberry_digi_driver = {
-+ .driver = {
-+ .name = "snd-rpi-boomberry-digi",
-+ .owner = THIS_MODULE,
-+ .of_match_table = snd_rpi_boomberry_digi_of_match,
-+ },
-+ .probe = snd_rpi_boomberry_digi_probe,
-+ .remove = snd_rpi_boomberry_digi_remove,
-+};
-+
-+module_platform_driver(snd_rpi_boomberry_digi_driver);
-+
-+MODULE_AUTHOR("Milan Neskovic <info at boomberry.co>");
-+MODULE_DESCRIPTION("ASoC Driver for BoomBerry PI Digi HAT Sound Card");
-+MODULE_LICENSE("GPL v2");
diff --git a/target/linux/brcm2708/patches-4.4/0242-Add-support-for-mcp7940x-family-of-RTC.patch b/target/linux/brcm2708/patches-4.4/0242-Add-support-for-mcp7940x-family-of-RTC.patch
deleted file mode 100644
index bdc7d68..0000000
--- a/target/linux/brcm2708/patches-4.4/0242-Add-support-for-mcp7940x-family-of-RTC.patch
+++ /dev/null
@@ -1,43 +0,0 @@
-From c4b87e2407fa4a7cfd95e9675ca2052702ab36e1 Mon Sep 17 00:00:00 2001
-From: Aaron Shaw <shawaj at gmail.com>
-Date: Fri, 8 Apr 2016 00:06:00 +0100
-Subject: [PATCH] Add support for mcp7940x family of RTC
-
----
- arch/arm/boot/dts/overlays/README | 2 ++
- arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts | 6 ++++++
- 2 files changed, 8 insertions(+)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -435,6 +435,8 @@ Params: ds1307 Select t
-
- ds3231 Select the DS3231 device
-
-+ mcp7940x Select the MCP7940x device
-+
- mcp7941x Select the MCP7941x device
-
- pcf2127 Select the PCF2127 device
---- a/arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts
-@@ -23,6 +23,11 @@
- reg = <0x68>;
- status = "disable";
- };
-+ mcp7940x: mcp7940x at 6f {
-+ compatible = "microchip,mcp7940x";
-+ reg = <0x6f>;
-+ status = "disable";
-+ };
- mcp7941x: mcp7941x at 6f {
- compatible = "microchip,mcp7941x";
- reg = <0x6f>;
-@@ -54,6 +59,7 @@
- ds1307 = <&ds1307>,"status";
- ds1339 = <&ds1339>,"status";
- ds3231 = <&ds3231>,"status";
-+ mcp7940x = <&mcp7940x>,"status";
- mcp7941x = <&mcp7941x>,"status";
- pcf2127 = <&pcf2127>,"status";
- pcf8523 = <&pcf8523>,"status";
diff --git a/target/linux/brcm2708/patches-4.4/0243-bcm2709_defconfig-Fix-typo-on-BoomBerry-configuratio.patch b/target/linux/brcm2708/patches-4.4/0243-bcm2709_defconfig-Fix-typo-on-BoomBerry-configuratio.patch
deleted file mode 100644
index 967a906..0000000
--- a/target/linux/brcm2708/patches-4.4/0243-bcm2709_defconfig-Fix-typo-on-BoomBerry-configuratio.patch
+++ /dev/null
@@ -1,22 +0,0 @@
-From 21b81df3c9039cd3c0894c025b7f1b114d27a2ba Mon Sep 17 00:00:00 2001
-From: Jeremy McDermond <nh6z at nh6z.net>
-Date: Thu, 14 Apr 2016 09:39:20 -0700
-Subject: [PATCH] bcm2709_defconfig: Fix typo on BoomBerry configuration
- directive
-
-The BoomBerry configuration directive in bcm2709_defconfig has a typo.
----
- arch/arm/configs/bcm2709_defconfig | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -854,7 +854,7 @@ CONFIG_SND_BCM2708_SOC_HIFIBERRY_DACPLUS
- CONFIG_SND_BCM2708_SOC_HIFIBERRY_DIGI=m
- CONFIG_SND_BCM2708_SOC_HIFIBERRY_AMP=m
- CONFIG_SND_BCM2708_SOC_BOOMBERRY_DAC=m
--CONFIG_SNG_BCM2708_SOC_BOOMBERRY_DIGI=m
-+CONFIG_SND_BCM2708_SOC_BOOMBERRY_DIGI=m
- CONFIG_SND_BCM2708_SOC_RPI_DAC=m
- CONFIG_SND_BCM2708_SOC_RPI_PROTO=m
- CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC=m
diff --git a/target/linux/brcm2708/patches-4.4/0244-boomberry-dac-Adjust-for-ALSA-API-change.patch b/target/linux/brcm2708/patches-4.4/0244-boomberry-dac-Adjust-for-ALSA-API-change.patch
deleted file mode 100644
index 9661afe..0000000
--- a/target/linux/brcm2708/patches-4.4/0244-boomberry-dac-Adjust-for-ALSA-API-change.patch
+++ /dev/null
@@ -1,26 +0,0 @@
-From 1fb5a7313cc2d1cab79c7ca9c93eb69ddf43071b Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 15 Apr 2016 10:48:39 +0100
-Subject: [PATCH] boomberry-dac: Adjust for ALSA API change
-
-As of 4.4, snd_soc_limit_volume now takes a struct snd_soc_card *
-rather than a struct snd_soc_codec *.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- sound/soc/bcm/boomberry-dac.c | 3 +--
- 1 file changed, 1 insertion(+), 2 deletions(-)
-
---- a/sound/soc/bcm/boomberry-dac.c
-+++ b/sound/soc/bcm/boomberry-dac.c
-@@ -40,9 +40,8 @@ static int snd_rpi_boomberry_dac_init(st
- {
- int ret;
- struct snd_soc_card *card = rtd->card;
-- struct snd_soc_codec *codec = rtd->codec;
-
-- ret = snd_soc_limit_volume(codec, "Digital Playback Volume", 207);
-+ ret = snd_soc_limit_volume(card, "Digital Playback Volume", 207);
- if (ret < 0)
- dev_warn(card->dev, "Failed to set volume limit: %d\n", ret);
- }
diff --git a/target/linux/brcm2708/patches-4.4/0245-vmcs-Remove-unused-sm_cache_map_vector-definition-14.patch b/target/linux/brcm2708/patches-4.4/0245-vmcs-Remove-unused-sm_cache_map_vector-definition-14.patch
deleted file mode 100644
index 5e6e65e..0000000
--- a/target/linux/brcm2708/patches-4.4/0245-vmcs-Remove-unused-sm_cache_map_vector-definition-14.patch
+++ /dev/null
@@ -1,34 +0,0 @@
-From 6c9401d37f03ab829f22e67c0941e04349df3e86 Mon Sep 17 00:00:00 2001
-From: Khem Raj <raj.khem at gmail.com>
-Date: Sun, 17 Apr 2016 04:44:47 -0700
-Subject: [PATCH] vmcs: Remove unused sm_cache_map_vector definition (#1411)
-
-The code using it also ifdef'ed with 0, anyyd gcc 6
-complains
-
-error: 'sm_cache_map_vector' defined but not used
-
-The code using it also ifdef'ed out
-
-Signed-off-by: Khem Raj <raj.khem at gmail.com>
----
- drivers/char/broadcom/vc_sm/vmcs_sm.c | 2 ++
- 1 file changed, 2 insertions(+)
-
---- a/drivers/char/broadcom/vc_sm/vmcs_sm.c
-+++ b/drivers/char/broadcom/vc_sm/vmcs_sm.c
-@@ -197,12 +197,14 @@ struct SM_STATE_T {
- static struct SM_STATE_T *sm_state;
- static int sm_inited;
-
-+#if 0
- static const char *const sm_cache_map_vector[] = {
- "(null)",
- "host",
- "videocore",
- "host+videocore",
- };
-+#endif
-
- /* ---- Private Function Prototypes -------------------------------------- */
-
diff --git a/target/linux/brcm2708/patches-4.4/0246-scripts-mkknlimg-Append-a-trailer-for-all-input.patch b/target/linux/brcm2708/patches-4.4/0246-scripts-mkknlimg-Append-a-trailer-for-all-input.patch
deleted file mode 100644
index 100c377..0000000
--- a/target/linux/brcm2708/patches-4.4/0246-scripts-mkknlimg-Append-a-trailer-for-all-input.patch
+++ /dev/null
@@ -1,63 +0,0 @@
-From 01d0d8d730b1687d078ee5e782eb2a3fa75afa7c Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 18 Apr 2016 11:56:53 +0100
-Subject: [PATCH] scripts/mkknlimg: Append a trailer for all input
-
-Now that the firmware assumes an unsigned kernel is DT-capable, it is
-helpful to be able to mark a kernel as being non-DT-capable.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- scripts/mkknlimg | 11 +++++------
- 1 file changed, 5 insertions(+), 6 deletions(-)
-
---- a/scripts/mkknlimg
-+++ b/scripts/mkknlimg
-@@ -98,7 +98,7 @@ my $append_trailer;
- my $trailer;
- my $kver = '?';
-
--$append_trailer = $dtok;
-+$append_trailer = 1;
-
- if ($res)
- {
-@@ -108,7 +108,6 @@ if ($res)
-
- if ($flags & FLAG_PI)
- {
-- $append_trailer = 1;
- $dtok ||= ($flags & FLAG_DTOK) != 0;
- $is_270x ||= ($flags & FLAG_270X) != 0;
- $is_283x ||= ($flags & FLAG_283X) != 0;
-@@ -116,18 +115,18 @@ if ($res)
- }
- else
- {
-- print ("* This doesn't look like a Raspberry Pi kernel. In pass-through mode.\n");
-+ print ("* This doesn't look like a Raspberry Pi kernel.\n");
- }
- }
- elsif (!$dtok)
- {
-- print ("* Is this a valid kernel? In pass-through mode.\n");
-+ print ("* Is this a valid kernel?\n");
- }
-
- if ($append_trailer)
- {
- printf("DT: %s\n", $dtok ? "y" : "n");
-- printf("DDT: %s\n", $ddtk ? "y" : "n") if ($ddtk);
-+ printf("DDT: %s\n", $ddtk ? "y" : "n");
- printf("270x: %s\n", $is_270x ? "y" : "n");
- printf("283x: %s\n", $is_283x ? "y" : "n");
-
-@@ -136,7 +135,7 @@ if ($append_trailer)
- push @atoms, [ $trailer_magic, pack('V', 0) ];
- push @atoms, [ 'KVer', $kver ];
- push @atoms, [ 'DTOK', pack('V', $dtok) ];
-- push @atoms, [ 'DDTK', pack('V', $ddtk) ] if ($ddtk);
-+ push @atoms, [ 'DDTK', pack('V', $ddtk) ];
- push @atoms, [ '270X', pack('V', $is_270x) ];
- push @atoms, [ '283X', pack('V', $is_283x) ];
- push @atoms, [ '283x', pack('V', $is_283x && !$is_270x) ];
diff --git a/target/linux/brcm2708/patches-4.4/0247-bcm2835_thermal-Don-t-report-unsupported-trip-type.patch b/target/linux/brcm2708/patches-4.4/0247-bcm2835_thermal-Don-t-report-unsupported-trip-type.patch
deleted file mode 100644
index e35d799..0000000
--- a/target/linux/brcm2708/patches-4.4/0247-bcm2835_thermal-Don-t-report-unsupported-trip-type.patch
+++ /dev/null
@@ -1,69 +0,0 @@
-From f0ccc27f25ee75c1df4f757d398ef78e85034ff0 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Tue, 19 Apr 2016 12:57:52 +0100
-Subject: [PATCH] bcm2835_thermal: Don't report unsupported trip type
-
----
- drivers/thermal/bcm2835-thermal.c | 34 +---------------------------------
- 1 file changed, 1 insertion(+), 33 deletions(-)
-
---- a/drivers/thermal/bcm2835-thermal.c
-+++ b/drivers/thermal/bcm2835-thermal.c
-@@ -49,38 +49,8 @@ static int bcm2835_thermal_get_temp(stru
- RPI_FIRMWARE_GET_TEMPERATURE);
- }
-
--static int bcm2835_thermal_get_max_temp(struct thermal_zone_device *tz,
-- int trip, int *temp)
--{
-- /*
-- * The maximum safe temperature of the SoC.
-- * Overclock may be disabled above this temperature.
-- */
-- return bcm2835_thermal_get_property(tz, temp,
-- RPI_FIRMWARE_GET_MAX_TEMPERATURE);
--}
--
--static int bcm2835_thermal_get_trip_type(struct thermal_zone_device *tz,
-- int trip, enum thermal_trip_type *type)
--{
-- *type = THERMAL_TRIP_HOT;
--
-- return 0;
--}
--
--static int bcm2835_thermal_get_mode(struct thermal_zone_device *tz,
-- enum thermal_device_mode *mode)
--{
-- *mode = THERMAL_DEVICE_ENABLED;
--
-- return 0;
--}
--
- static struct thermal_zone_device_ops ops = {
- .get_temp = bcm2835_thermal_get_temp,
-- .get_trip_temp = bcm2835_thermal_get_max_temp,
-- .get_trip_type = bcm2835_thermal_get_trip_type,
-- .get_mode = bcm2835_thermal_get_mode,
- };
-
- static int bcm2835_thermal_probe(struct platform_device *pdev)
-@@ -90,17 +60,15 @@ static int bcm2835_thermal_probe(struct
- struct thermal_zone_device *tz;
-
- fw_np = of_parse_phandle(pdev->dev.of_node, "firmware", 0);
--/* Remove comment when booting without Device Tree is no longer supported
- if (!fw_np) {
- dev_err(&pdev->dev, "Missing firmware node\n");
- return -ENOENT;
- }
--*/
- fw = rpi_firmware_get(fw_np);
- if (!fw)
- return -EPROBE_DEFER;
-
-- tz = thermal_zone_device_register("bcm2835_thermal", 1, 0, fw, &ops,
-+ tz = thermal_zone_device_register("bcm2835_thermal", 0, 0, fw, &ops,
- NULL, 0, 0);
- if (IS_ERR(tz)) {
- dev_err(&pdev->dev, "Failed to register the thermal device\n");
diff --git a/target/linux/brcm2708/patches-4.4/0248-scripts-dtc-Only-emit-local-fixups-for-overlays.patch b/target/linux/brcm2708/patches-4.4/0248-scripts-dtc-Only-emit-local-fixups-for-overlays.patch
deleted file mode 100644
index 28c56cd..0000000
--- a/target/linux/brcm2708/patches-4.4/0248-scripts-dtc-Only-emit-local-fixups-for-overlays.patch
+++ /dev/null
@@ -1,21 +0,0 @@
-From 6fa3d052ad8aeedaec70d5b3f143009c5a0fea46 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Tue, 19 Apr 2016 13:55:29 +0100
-Subject: [PATCH] scripts/dtc: Only emit local fixups for overlays
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- scripts/dtc/checks.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/scripts/dtc/checks.c
-+++ b/scripts/dtc/checks.c
-@@ -514,7 +514,7 @@ static void fixup_phandle_references(str
- }
-
- /* if it's a local reference, we need to record it */
-- if (symbol_fixup_support) {
-+ if (symbol_fixup_support && dt->is_plugin) {
-
- /* allocate a new local fixup entry */
- fe = xmalloc(sizeof(*fe));
diff --git a/target/linux/brcm2708/patches-4.4/0249-bcm2835-do-not-require-substream-for-accessing-chmap.patch b/target/linux/brcm2708/patches-4.4/0249-bcm2835-do-not-require-substream-for-accessing-chmap.patch
deleted file mode 100644
index 5699987..0000000
--- a/target/linux/brcm2708/patches-4.4/0249-bcm2835-do-not-require-substream-for-accessing-chmap.patch
+++ /dev/null
@@ -1,50 +0,0 @@
-From dd5d430ef916b934dab137d32562c80b737d7738 Mon Sep 17 00:00:00 2001
-From: wm4 <wm4 at nowhere>
-Date: Tue, 19 Apr 2016 16:08:35 +0200
-Subject: [PATCH] bcm2835: do not require substream for accessing chmap ctl
-
-Fixes alsasctl store/restore operation.
----
- sound/arm/bcm2835-ctl.c | 10 +---------
- 1 file changed, 1 insertion(+), 9 deletions(-)
-
---- a/sound/arm/bcm2835-ctl.c
-+++ b/sound/arm/bcm2835-ctl.c
-@@ -489,8 +489,6 @@ static int snd_bcm2835_chmap_ctl_get(str
- {
- struct snd_pcm_chmap *info = snd_kcontrol_chip(kcontrol);
- bcm2835_chip_t *chip = info->private_data;
-- unsigned int idx = snd_ctl_get_ioffidx(kcontrol, &ucontrol->id);
-- struct snd_pcm_substream *substream = snd_pcm_chmap_substream(info, idx);
- struct cea_channel_speaker_allocation *ch = NULL;
- int res = 0;
- int cur = 0;
-@@ -499,11 +497,6 @@ static int snd_bcm2835_chmap_ctl_get(str
- if (mutex_lock_interruptible(&chip->audio_mutex))
- return -EINTR;
-
-- if (!substream || !substream->runtime) {
-- res = -ENODEV;
-- goto unlock;
-- }
--
- for (i = 0; i < ARRAY_SIZE(channel_allocations); i++) {
- if (channel_allocations[i].ca_index == chip->cea_chmap)
- ch = &channel_allocations[i];
-@@ -521,7 +514,6 @@ static int snd_bcm2835_chmap_ctl_get(str
- while (cur < 8)
- ucontrol->value.integer.value[cur++] = SNDRV_CHMAP_NA;
-
--unlock:
- mutex_unlock(&chip->audio_mutex);
- return res;
- }
-@@ -541,7 +533,7 @@ static int snd_bcm2835_chmap_ctl_put(str
- return -EINTR;
-
- if (!substream || !substream->runtime) {
-- res = -ENODEV;
-+ /* ignore and return success for the sake of alsactl */
- goto unlock;
- }
-
diff --git a/target/linux/brcm2708/patches-4.4/0250-bcm2835-add-fallback-channel-layouts-if-channel-map-.patch b/target/linux/brcm2708/patches-4.4/0250-bcm2835-add-fallback-channel-layouts-if-channel-map-.patch
deleted file mode 100644
index 5a4009d..0000000
--- a/target/linux/brcm2708/patches-4.4/0250-bcm2835-add-fallback-channel-layouts-if-channel-map-.patch
+++ /dev/null
@@ -1,41 +0,0 @@
-From 5710f5696b9db1108e1643a5967a5b576c32b8a0 Mon Sep 17 00:00:00 2001
-From: wm4 <wm4 at nowhere>
-Date: Tue, 19 Apr 2016 16:29:41 +0200
-Subject: [PATCH] bcm2835: add fallback channel layouts if channel map API is
- not used
-
-Should be more useful than just forcing stereo.
-
-We can't match the exact legacy ALSA channel layouts, so this is a
-"best effort" hack.
-
-I'm not sure what happens if the application requests channel counts
-that are not power-of-2s. The channel map API hopefully forces
-applications which use the channel map API to request the correct
-count by adding padding channels, but the bare API enforces
-nothing. Possibly this could be added to rate_hw_constraint_channels
-at a later point.
----
- sound/arm/bcm2835-vchiq.c | 11 ++++++++++-
- 1 file changed, 10 insertions(+), 1 deletion(-)
-
---- a/sound/arm/bcm2835-vchiq.c
-+++ b/sound/arm/bcm2835-vchiq.c
-@@ -598,7 +598,16 @@ int bcm2835_audio_set_params(bcm2835_als
- if (alsa_stream->chip->cea_chmap >= 0) {
- chmap_value = (unsigned)alsa_stream->chip->cea_chmap << 24;
- } else {
-- chmap_value = 0; /* force stereo */
-+ /* fallback layouts for applications which do not use chmap API */
-+ chmap_value = 0x00;
-+ switch (channels) {
-+ case 3: chmap_value = 0x01; break;
-+ case 4: chmap_value = 0x03; break;
-+ case 5: chmap_value = 0x07; break;
-+ case 6: chmap_value = 0x0b; break;
-+ case 7: chmap_value = 0x0f; break;
-+ case 8: chmap_value = 0x13; break;
-+ }
- for (i = 0; i < 8; i++)
- alsa_stream->chip->map_channels[i] = i;
- }
diff --git a/target/linux/brcm2708/patches-4.4/0251-bcm2835-log-which-channel-map-is-set.patch b/target/linux/brcm2708/patches-4.4/0251-bcm2835-log-which-channel-map-is-set.patch
deleted file mode 100644
index f39b433..0000000
--- a/target/linux/brcm2708/patches-4.4/0251-bcm2835-log-which-channel-map-is-set.patch
+++ /dev/null
@@ -1,32 +0,0 @@
-From a35699c1a20bfe4c4b268dd6697a026a32a18e2f Mon Sep 17 00:00:00 2001
-From: wm4 <wm4 at nowhere>
-Date: Tue, 19 Apr 2016 16:38:03 +0200
-Subject: [PATCH] bcm2835: log which channel map is set
-
----
- sound/arm/bcm2835-vchiq.c | 5 +++++
- 1 file changed, 5 insertions(+)
-
---- a/sound/arm/bcm2835-vchiq.c
-+++ b/sound/arm/bcm2835-vchiq.c
-@@ -596,8 +596,11 @@ int bcm2835_audio_set_params(bcm2835_als
- instance->result = -1;
-
- if (alsa_stream->chip->cea_chmap >= 0) {
-+ LOG_INFO("Using application requested channel map: %d\n",
-+ alsa_stream->chip->cea_chmap);
- chmap_value = (unsigned)alsa_stream->chip->cea_chmap << 24;
- } else {
-+ LOG_INFO("Using fallback channel map.\n");
- /* fallback layouts for applications which do not use chmap API */
- chmap_value = 0x00;
- switch (channels) {
-@@ -614,6 +617,8 @@ int bcm2835_audio_set_params(bcm2835_als
- for (i = 0; i < 8; i++)
- chmap_value |= alsa_stream->chip->map_channels[i] << (i * 3);
-
-+ LOG_INFO("Requesting AUDS channel map: 0x%lx\n", (long)chmap_value);
-+
- m.type = VC_AUDIO_MSG_TYPE_CONFIG;
- m.u.config.channels = channels;
- m.u.config.samplerate = samplerate;
diff --git a/target/linux/brcm2708/patches-4.4/0252-clk-bcm2835-add-a-round-up-ability-to-the-clock-divi.patch b/target/linux/brcm2708/patches-4.4/0252-clk-bcm2835-add-a-round-up-ability-to-the-clock-divi.patch
deleted file mode 100644
index 65aed5c..0000000
--- a/target/linux/brcm2708/patches-4.4/0252-clk-bcm2835-add-a-round-up-ability-to-the-clock-divi.patch
+++ /dev/null
@@ -1,69 +0,0 @@
-From e17280a589eede384ca578a4f1f35a1f3b066360 Mon Sep 17 00:00:00 2001
-From: Remi Pommarel <repk at triplefau.lt>
-Date: Sun, 6 Dec 2015 17:22:46 +0100
-Subject: [PATCH] clk: bcm2835: add a round up ability to the clock divisor
-
-Make bcm2835_clock_choose_div to optionally round up the chosen MASH divisor
-so that the resulting average rate will not be higher than the requested one.
-
-Signed-off-by: Remi Pommarel <repk at triplefau.lt>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Michael Turquette <mturquette at baylibre.com>
-(cherry picked from commit 9c95b32ca09364e4687b72c4e17b78dc1c420026)
----
- drivers/clk/bcm/clk-bcm2835.c | 22 ++++++++++++----------
- 1 file changed, 12 insertions(+), 10 deletions(-)
-
---- a/drivers/clk/bcm/clk-bcm2835.c
-+++ b/drivers/clk/bcm/clk-bcm2835.c
-@@ -1166,22 +1166,24 @@ static int bcm2835_clock_is_on(struct cl
-
- static u32 bcm2835_clock_choose_div(struct clk_hw *hw,
- unsigned long rate,
-- unsigned long parent_rate)
-+ unsigned long parent_rate,
-+ bool round_up)
- {
- struct bcm2835_clock *clock = bcm2835_clock_from_hw(hw);
- const struct bcm2835_clock_data *data = clock->data;
-- u32 unused_frac_mask = GENMASK(CM_DIV_FRAC_BITS - data->frac_bits, 0);
-+ u32 unused_frac_mask =
-+ GENMASK(CM_DIV_FRAC_BITS - data->frac_bits, 0) >> 1;
- u64 temp = (u64)parent_rate << CM_DIV_FRAC_BITS;
-+ u64 rem;
- u32 div;
-
-- do_div(temp, rate);
-+ rem = do_div(temp, rate);
- div = temp;
-
-- /* Round and mask off the unused bits */
-- if (unused_frac_mask != 0) {
-- div += unused_frac_mask >> 1;
-- div &= ~unused_frac_mask;
-- }
-+ /* Round up and mask off the unused bits */
-+ if (round_up && ((div & unused_frac_mask) != 0 || rem != 0))
-+ div += unused_frac_mask + 1;
-+ div &= ~unused_frac_mask;
-
- /* clamp to min divider of 1 */
- div = max_t(u32, div, 1 << CM_DIV_FRAC_BITS);
-@@ -1221,7 +1223,7 @@ static long bcm2835_clock_round_rate(str
- unsigned long *parent_rate)
- {
- struct bcm2835_clock *clock = bcm2835_clock_from_hw(hw);
-- u32 div = bcm2835_clock_choose_div(hw, rate, *parent_rate);
-+ u32 div = bcm2835_clock_choose_div(hw, rate, *parent_rate, false);
-
- return bcm2835_clock_rate_from_divisor(clock, *parent_rate, div);
- }
-@@ -1290,7 +1292,7 @@ static int bcm2835_clock_set_rate(struct
- struct bcm2835_clock *clock = bcm2835_clock_from_hw(hw);
- struct bcm2835_cprman *cprman = clock->cprman;
- const struct bcm2835_clock_data *data = clock->data;
-- u32 div = bcm2835_clock_choose_div(hw, rate, parent_rate);
-+ u32 div = bcm2835_clock_choose_div(hw, rate, parent_rate, false);
-
- cprman_write(cprman, data->div_reg, div);
-
diff --git a/target/linux/brcm2708/patches-4.4/0253-clk-bcm2835-Support-for-clock-parent-selection.patch b/target/linux/brcm2708/patches-4.4/0253-clk-bcm2835-Support-for-clock-parent-selection.patch
deleted file mode 100644
index 13bb740..0000000
--- a/target/linux/brcm2708/patches-4.4/0253-clk-bcm2835-Support-for-clock-parent-selection.patch
+++ /dev/null
@@ -1,188 +0,0 @@
-From 7a4e9397156fd222f04eb86564a04cc647b99b76 Mon Sep 17 00:00:00 2001
-From: Remi Pommarel <repk at triplefau.lt>
-Date: Sun, 6 Dec 2015 17:22:47 +0100
-Subject: [PATCH] clk: bcm2835: Support for clock parent selection
-
-Some bcm2835 clocks used by hardware (like "PWM" or "H264") can have multiple
-parent clocks. These clocks divide the rate of a parent which can be selected by
-setting the proper bits in the clock control register.
-
-Previously all these parents where handled by a mux clock. But a mux clock
-cannot be used because updating clock control register to select parent needs a
-password to be xor'd with the parent index.
-
-This patch get rid of mux clock and make these clocks handle their own parent,
-allowing them to select the one to use.
-
-Signed-off-by: Remi Pommarel <repk at triplefau.lt>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Michael Turquette <mturquette at baylibre.com>
-(cherry picked from commit 6d18b8adbe679b5947aa822b676efff230acc5f6)
----
- drivers/clk/bcm/clk-bcm2835.c | 122 ++++++++++++++++++++++++++----------------
- 1 file changed, 77 insertions(+), 45 deletions(-)
-
---- a/drivers/clk/bcm/clk-bcm2835.c
-+++ b/drivers/clk/bcm/clk-bcm2835.c
-@@ -1218,16 +1218,6 @@ static long bcm2835_clock_rate_from_divi
- return temp;
- }
-
--static long bcm2835_clock_round_rate(struct clk_hw *hw,
-- unsigned long rate,
-- unsigned long *parent_rate)
--{
-- struct bcm2835_clock *clock = bcm2835_clock_from_hw(hw);
-- u32 div = bcm2835_clock_choose_div(hw, rate, *parent_rate, false);
--
-- return bcm2835_clock_rate_from_divisor(clock, *parent_rate, div);
--}
--
- static unsigned long bcm2835_clock_get_rate(struct clk_hw *hw,
- unsigned long parent_rate)
- {
-@@ -1299,13 +1289,75 @@ static int bcm2835_clock_set_rate(struct
- return 0;
- }
-
-+static int bcm2835_clock_determine_rate(struct clk_hw *hw,
-+ struct clk_rate_request *req)
-+{
-+ struct bcm2835_clock *clock = bcm2835_clock_from_hw(hw);
-+ struct clk_hw *parent, *best_parent = NULL;
-+ unsigned long rate, best_rate = 0;
-+ unsigned long prate, best_prate = 0;
-+ size_t i;
-+ u32 div;
-+
-+ /*
-+ * Select parent clock that results in the closest but lower rate
-+ */
-+ for (i = 0; i < clk_hw_get_num_parents(hw); ++i) {
-+ parent = clk_hw_get_parent_by_index(hw, i);
-+ if (!parent)
-+ continue;
-+ prate = clk_hw_get_rate(parent);
-+ div = bcm2835_clock_choose_div(hw, req->rate, prate, true);
-+ rate = bcm2835_clock_rate_from_divisor(clock, prate, div);
-+ if (rate > best_rate && rate <= req->rate) {
-+ best_parent = parent;
-+ best_prate = prate;
-+ best_rate = rate;
-+ }
-+ }
-+
-+ if (!best_parent)
-+ return -EINVAL;
-+
-+ req->best_parent_hw = best_parent;
-+ req->best_parent_rate = best_prate;
-+
-+ req->rate = best_rate;
-+
-+ return 0;
-+}
-+
-+static int bcm2835_clock_set_parent(struct clk_hw *hw, u8 index)
-+{
-+ struct bcm2835_clock *clock = bcm2835_clock_from_hw(hw);
-+ struct bcm2835_cprman *cprman = clock->cprman;
-+ const struct bcm2835_clock_data *data = clock->data;
-+ u8 src = (index << CM_SRC_SHIFT) & CM_SRC_MASK;
-+
-+ cprman_write(cprman, data->ctl_reg, src);
-+ return 0;
-+}
-+
-+static u8 bcm2835_clock_get_parent(struct clk_hw *hw)
-+{
-+ struct bcm2835_clock *clock = bcm2835_clock_from_hw(hw);
-+ struct bcm2835_cprman *cprman = clock->cprman;
-+ const struct bcm2835_clock_data *data = clock->data;
-+ u32 src = cprman_read(cprman, data->ctl_reg);
-+
-+ return (src & CM_SRC_MASK) >> CM_SRC_SHIFT;
-+}
-+
-+
- static const struct clk_ops bcm2835_clock_clk_ops = {
- .is_prepared = bcm2835_clock_is_on,
- .prepare = bcm2835_clock_on,
- .unprepare = bcm2835_clock_off,
- .recalc_rate = bcm2835_clock_get_rate,
- .set_rate = bcm2835_clock_set_rate,
-- .round_rate = bcm2835_clock_round_rate,
-+ .determine_rate = bcm2835_clock_determine_rate,
-+ .set_parent = bcm2835_clock_set_parent,
-+ .get_parent = bcm2835_clock_get_parent,
- };
-
- static int bcm2835_vpu_clock_is_on(struct clk_hw *hw)
-@@ -1321,7 +1373,9 @@ static const struct clk_ops bcm2835_vpu_
- .is_prepared = bcm2835_vpu_clock_is_on,
- .recalc_rate = bcm2835_clock_get_rate,
- .set_rate = bcm2835_clock_set_rate,
-- .round_rate = bcm2835_clock_round_rate,
-+ .determine_rate = bcm2835_clock_determine_rate,
-+ .set_parent = bcm2835_clock_set_parent,
-+ .get_parent = bcm2835_clock_get_parent,
- };
-
- static struct clk *bcm2835_register_pll(struct bcm2835_cprman *cprman,
-@@ -1415,45 +1469,23 @@ static struct clk *bcm2835_register_cloc
- {
- struct bcm2835_clock *clock;
- struct clk_init_data init;
-- const char *parent;
-+ const char *parents[1 << CM_SRC_BITS];
-+ size_t i;
-
- /*
-- * Most of the clock generators have a mux field, so we
-- * instantiate a generic mux as our parent to handle it.
-+ * Replace our "xosc" references with the oscillator's
-+ * actual name.
- */
-- if (data->num_mux_parents) {
-- const char *parents[1 << CM_SRC_BITS];
-- int i;
--
-- parent = devm_kasprintf(cprman->dev, GFP_KERNEL,
-- "mux_%s", data->name);
-- if (!parent)
-- return NULL;
--
-- /*
-- * Replace our "xosc" references with the oscillator's
-- * actual name.
-- */
-- for (i = 0; i < data->num_mux_parents; i++) {
-- if (strcmp(data->parents[i], "xosc") == 0)
-- parents[i] = cprman->osc_name;
-- else
-- parents[i] = data->parents[i];
-- }
--
-- clk_register_mux(cprman->dev, parent,
-- parents, data->num_mux_parents,
-- CLK_SET_RATE_PARENT,
-- cprman->regs + data->ctl_reg,
-- CM_SRC_SHIFT, CM_SRC_BITS,
-- 0, &cprman->regs_lock);
-- } else {
-- parent = data->parents[0];
-+ for (i = 0; i < data->num_mux_parents; i++) {
-+ if (strcmp(data->parents[i], "xosc") == 0)
-+ parents[i] = cprman->osc_name;
-+ else
-+ parents[i] = data->parents[i];
- }
-
- memset(&init, 0, sizeof(init));
-- init.parent_names = &parent;
-- init.num_parents = 1;
-+ init.parent_names = parents;
-+ init.num_parents = data->num_mux_parents;
- init.name = data->name;
- init.flags = CLK_IGNORE_UNUSED;
-
diff --git a/target/linux/brcm2708/patches-4.4/0254-clk-bcm2835-Add-PWM-clock-support.patch b/target/linux/brcm2708/patches-4.4/0254-clk-bcm2835-Add-PWM-clock-support.patch
deleted file mode 100644
index fbe0b7c..0000000
--- a/target/linux/brcm2708/patches-4.4/0254-clk-bcm2835-Add-PWM-clock-support.patch
+++ /dev/null
@@ -1,55 +0,0 @@
-From 8ee53ca609a2c7747b36a2fb3eb7eadcd79f5b29 Mon Sep 17 00:00:00 2001
-From: Remi Pommarel <repk at triplefau.lt>
-Date: Sun, 6 Dec 2015 17:22:48 +0100
-Subject: [PATCH] clk: bcm2835: Add PWM clock support
-
-Register the pwm clock for bcm2835.
-
-Signed-off-by: Remi Pommarel <repk at triplefau.lt>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Michael Turquette <mturquette at baylibre.com>
-(cherry picked from commit cfbab8fbab9c330aca963095a439c451ac97c0dd)
----
- drivers/clk/bcm/clk-bcm2835.c | 13 +++++++++++++
- include/dt-bindings/clock/bcm2835.h | 3 ++-
- 2 files changed, 15 insertions(+), 1 deletion(-)
-
---- a/drivers/clk/bcm/clk-bcm2835.c
-+++ b/drivers/clk/bcm/clk-bcm2835.c
-@@ -807,6 +807,16 @@ static const struct bcm2835_clock_data b
- .frac_bits = 8,
- };
-
-+static const struct bcm2835_clock_data bcm2835_clock_pwm_data = {
-+ .name = "pwm",
-+ .num_mux_parents = ARRAY_SIZE(bcm2835_clock_per_parents),
-+ .parents = bcm2835_clock_per_parents,
-+ .ctl_reg = CM_PWMCTL,
-+ .div_reg = CM_PWMDIV,
-+ .int_bits = 12,
-+ .frac_bits = 12,
-+};
-+
- struct bcm2835_pll {
- struct clk_hw hw;
- struct bcm2835_cprman *cprman;
-@@ -1603,6 +1613,9 @@ static int bcm2835_clk_probe(struct plat
- cprman->regs + CM_PERIICTL, CM_GATE_BIT,
- 0, &cprman->regs_lock);
-
-+ clks[BCM2835_CLOCK_PWM] =
-+ bcm2835_register_clock(cprman, &bcm2835_clock_pwm_data);
-+
- return of_clk_add_provider(dev->of_node, of_clk_src_onecell_get,
- &cprman->onecell);
- }
---- a/include/dt-bindings/clock/bcm2835.h
-+++ b/include/dt-bindings/clock/bcm2835.h
-@@ -43,5 +43,6 @@
- #define BCM2835_CLOCK_TSENS 27
- #define BCM2835_CLOCK_EMMC 28
- #define BCM2835_CLOCK_PERI_IMAGE 29
-+#define BCM2835_CLOCK_PWM 30
-
--#define BCM2835_CLOCK_COUNT 30
-+#define BCM2835_CLOCK_COUNT 31
diff --git a/target/linux/brcm2708/patches-4.4/0255-clk-bcm2835-added-missing-clock-register-definitions.patch b/target/linux/brcm2708/patches-4.4/0255-clk-bcm2835-added-missing-clock-register-definitions.patch
deleted file mode 100644
index 487751f..0000000
--- a/target/linux/brcm2708/patches-4.4/0255-clk-bcm2835-added-missing-clock-register-definitions.patch
+++ /dev/null
@@ -1,48 +0,0 @@
-From 324fca092b17a2affebeb89a35f53b6512ded4d0 Mon Sep 17 00:00:00 2001
-From: Martin Sperl <kernel at martin.sperl.org>
-Date: Tue, 22 Dec 2015 20:13:08 +0000
-Subject: [PATCH] clk: bcm2835: added missing clock register definitions
-
-Added missing CTRL and DIV clock register definitions for:
-PCM, SLIM, TCNT, TEC, TD0, TD1
-
-Register information taken from:
-https://rawgit.com/msperl/rpi-registers/master/rpi-registers.html#CM
-which extracted the information from the header files shared by
-Broadcom/rpi foundation in this file:
-http://www.broadcom.com/docs/support/videocore/Brcm_Android_ICS_Graphics_Stack.tar.gz
-
-Signed-off-by: Martin Sperl <kernel at martin.sperl.org>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
-(cherry picked from commit 2103a2156119b30f5924af2a1094227954be4617)
----
- drivers/clk/bcm/clk-bcm2835.c | 13 +++++++++++++
- 1 file changed, 13 insertions(+)
-
---- a/drivers/clk/bcm/clk-bcm2835.c
-+++ b/drivers/clk/bcm/clk-bcm2835.c
-@@ -88,10 +88,23 @@
- #define CM_HSMDIV 0x08c
- #define CM_OTPCTL 0x090
- #define CM_OTPDIV 0x094
-+#define CM_PCMCTL 0x098
-+#define CM_PCMDIV 0x09c
- #define CM_PWMCTL 0x0a0
- #define CM_PWMDIV 0x0a4
-+#define CM_SLIMCTL 0x0a8
-+#define CM_SLIMDIV 0x0ac
- #define CM_SMICTL 0x0b0
- #define CM_SMIDIV 0x0b4
-+/* no definition for 0x0b8 and 0x0bc */
-+#define CM_TCNTCTL 0x0c0
-+#define CM_TCNTDIV 0x0c4
-+#define CM_TECCTL 0x0c8
-+#define CM_TECDIV 0x0cc
-+#define CM_TD0CTL 0x0d0
-+#define CM_TD0DIV 0x0d4
-+#define CM_TD1CTL 0x0d8
-+#define CM_TD1DIV 0x0dc
- #define CM_TSENSCTL 0x0e0
- #define CM_TSENSDIV 0x0e4
- #define CM_TIMERCTL 0x0e8
diff --git a/target/linux/brcm2708/patches-4.4/0256-clk-bcm2835-correctly-enable-fractional-clock-suppor.patch b/target/linux/brcm2708/patches-4.4/0256-clk-bcm2835-correctly-enable-fractional-clock-suppor.patch
deleted file mode 100644
index e9f7a0e..0000000
--- a/target/linux/brcm2708/patches-4.4/0256-clk-bcm2835-correctly-enable-fractional-clock-suppor.patch
+++ /dev/null
@@ -1,133 +0,0 @@
-From c12ba7510cbd151a718423967c89d5dca053040f Mon Sep 17 00:00:00 2001
-From: Martin Sperl <kernel at martin.sperl.org>
-Date: Mon, 29 Feb 2016 11:39:21 +0000
-Subject: [PATCH] clk: bcm2835: correctly enable fractional clock support
-
-The current driver calculates the clock divider with
-fractional support enabled.
-
-But it does not enable fractional support in the
-control register itself resulting in an integer only divider,
-but in clk_set_rate responds back the fractionally divided
-clock frequency.
-
-This patch enables fractional support in the control register
-whenever there is a fractional bit set in the requested clock divider.
-
-Mash clock limits are are also handled for the PWM clock
-applying the correct divider limits (2 and max_int) applicable to
-basic fractional divider support (mash order of 1).
-
-It also adds locking to protect the read/modify/write cycle of
-the register modification.
-
-Fixes: 41691b8862e2 ("clk: bcm2835: Add support for programming the
-audio domain clocks")
-
-Signed-off-by: Martin Sperl <kernel at martin.sperl.org>
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 959ca92a3235fc4b17c1e18483fc390b3d612254)
----
- drivers/clk/bcm/clk-bcm2835.c | 45 +++++++++++++++++++++++++++++++++++++------
- 1 file changed, 39 insertions(+), 6 deletions(-)
-
---- a/drivers/clk/bcm/clk-bcm2835.c
-+++ b/drivers/clk/bcm/clk-bcm2835.c
-@@ -51,6 +51,7 @@
- #define CM_GNRICCTL 0x000
- #define CM_GNRICDIV 0x004
- # define CM_DIV_FRAC_BITS 12
-+# define CM_DIV_FRAC_MASK GENMASK(CM_DIV_FRAC_BITS - 1, 0)
-
- #define CM_VPUCTL 0x008
- #define CM_VPUDIV 0x00c
-@@ -128,6 +129,7 @@
- # define CM_GATE BIT(CM_GATE_BIT)
- # define CM_BUSY BIT(7)
- # define CM_BUSYD BIT(8)
-+# define CM_FRAC BIT(9)
- # define CM_SRC_SHIFT 0
- # define CM_SRC_BITS 4
- # define CM_SRC_MASK 0xf
-@@ -647,6 +649,7 @@ struct bcm2835_clock_data {
- u32 frac_bits;
-
- bool is_vpu_clock;
-+ bool is_mash_clock;
- };
-
- static const char *const bcm2835_clock_per_parents[] = {
-@@ -828,6 +831,7 @@ static const struct bcm2835_clock_data b
- .div_reg = CM_PWMDIV,
- .int_bits = 12,
- .frac_bits = 12,
-+ .is_mash_clock = true,
- };
-
- struct bcm2835_pll {
-@@ -1198,7 +1202,7 @@ static u32 bcm2835_clock_choose_div(stru
- GENMASK(CM_DIV_FRAC_BITS - data->frac_bits, 0) >> 1;
- u64 temp = (u64)parent_rate << CM_DIV_FRAC_BITS;
- u64 rem;
-- u32 div;
-+ u32 div, mindiv, maxdiv;
-
- rem = do_div(temp, rate);
- div = temp;
-@@ -1208,11 +1212,23 @@ static u32 bcm2835_clock_choose_div(stru
- div += unused_frac_mask + 1;
- div &= ~unused_frac_mask;
-
-- /* clamp to min divider of 1 */
-- div = max_t(u32, div, 1 << CM_DIV_FRAC_BITS);
-- /* clamp to the highest possible fractional divider */
-- div = min_t(u32, div, GENMASK(data->int_bits + CM_DIV_FRAC_BITS - 1,
-- CM_DIV_FRAC_BITS - data->frac_bits));
-+ /* different clamping limits apply for a mash clock */
-+ if (data->is_mash_clock) {
-+ /* clamp to min divider of 2 */
-+ mindiv = 2 << CM_DIV_FRAC_BITS;
-+ /* clamp to the highest possible integer divider */
-+ maxdiv = (BIT(data->int_bits) - 1) << CM_DIV_FRAC_BITS;
-+ } else {
-+ /* clamp to min divider of 1 */
-+ mindiv = 1 << CM_DIV_FRAC_BITS;
-+ /* clamp to the highest possible fractional divider */
-+ maxdiv = GENMASK(data->int_bits + CM_DIV_FRAC_BITS - 1,
-+ CM_DIV_FRAC_BITS - data->frac_bits);
-+ }
-+
-+ /* apply the clamping limits */
-+ div = max_t(u32, div, mindiv);
-+ div = min_t(u32, div, maxdiv);
-
- return div;
- }
-@@ -1306,9 +1322,26 @@ static int bcm2835_clock_set_rate(struct
- struct bcm2835_cprman *cprman = clock->cprman;
- const struct bcm2835_clock_data *data = clock->data;
- u32 div = bcm2835_clock_choose_div(hw, rate, parent_rate, false);
-+ u32 ctl;
-+
-+ spin_lock(&cprman->regs_lock);
-+
-+ /*
-+ * Setting up frac support
-+ *
-+ * In principle it is recommended to stop/start the clock first,
-+ * but as we set CLK_SET_RATE_GATE during registration of the
-+ * clock this requirement should be take care of by the
-+ * clk-framework.
-+ */
-+ ctl = cprman_read(cprman, data->ctl_reg) & ~CM_FRAC;
-+ ctl |= (div & CM_DIV_FRAC_MASK) ? CM_FRAC : 0;
-+ cprman_write(cprman, data->ctl_reg, ctl);
-
- cprman_write(cprman, data->div_reg, div);
-
-+ spin_unlock(&cprman->regs_lock);
-+
- return 0;
- }
-
diff --git a/target/linux/brcm2708/patches-4.4/0257-clk-bcm2835-clean-up-coding-style-issues.patch b/target/linux/brcm2708/patches-4.4/0257-clk-bcm2835-clean-up-coding-style-issues.patch
deleted file mode 100644
index 0fcff80..0000000
--- a/target/linux/brcm2708/patches-4.4/0257-clk-bcm2835-clean-up-coding-style-issues.patch
+++ /dev/null
@@ -1,52 +0,0 @@
-From 7fea22b10a3cf07ea0f3b5ffb7c31f6e341cdd6b Mon Sep 17 00:00:00 2001
-From: Martin Sperl <kernel at martin.sperl.org>
-Date: Mon, 29 Feb 2016 11:39:22 +0000
-Subject: [PATCH] clk: bcm2835: clean up coding style issues
-
-Fix all the checkpatch complaints for clk-bcm2835.c
-
-Signed-off-by: Martin Sperl <kernel at martin.sperl.org>
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 6e1e60dacee7b32aef1468ea461b02e4c7a90a45)
----
- drivers/clk/bcm/clk-bcm2835.c | 8 ++------
- 1 file changed, 2 insertions(+), 6 deletions(-)
-
---- a/drivers/clk/bcm/clk-bcm2835.c
-+++ b/drivers/clk/bcm/clk-bcm2835.c
-@@ -12,9 +12,6 @@
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
-- * You should have received a copy of the GNU General Public License
-- * along with this program; if not, write to the Free Software
-- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
- /**
-@@ -299,7 +296,7 @@
- struct bcm2835_cprman {
- struct device *dev;
- void __iomem *regs;
-- spinlock_t regs_lock;
-+ spinlock_t regs_lock; /* spinlock for all clocks */
- const char *osc_name;
-
- struct clk_onecell_data onecell;
-@@ -1346,7 +1343,7 @@ static int bcm2835_clock_set_rate(struct
- }
-
- static int bcm2835_clock_determine_rate(struct clk_hw *hw,
-- struct clk_rate_request *req)
-+ struct clk_rate_request *req)
- {
- struct bcm2835_clock *clock = bcm2835_clock_from_hw(hw);
- struct clk_hw *parent, *best_parent = NULL;
-@@ -1404,7 +1401,6 @@ static u8 bcm2835_clock_get_parent(struc
- return (src & CM_SRC_MASK) >> CM_SRC_SHIFT;
- }
-
--
- static const struct clk_ops bcm2835_clock_clk_ops = {
- .is_prepared = bcm2835_clock_is_on,
- .prepare = bcm2835_clock_on,
diff --git a/target/linux/brcm2708/patches-4.4/0258-clk-bcm2835-expose-raw-clock-registers-via-debugfs.patch b/target/linux/brcm2708/patches-4.4/0258-clk-bcm2835-expose-raw-clock-registers-via-debugfs.patch
deleted file mode 100644
index b736245..0000000
--- a/target/linux/brcm2708/patches-4.4/0258-clk-bcm2835-expose-raw-clock-registers-via-debugfs.patch
+++ /dev/null
@@ -1,188 +0,0 @@
-From 480388d3fa7727888533e9a745f05fb363f527f9 Mon Sep 17 00:00:00 2001
-From: Martin Sperl <kernel at martin.sperl.org>
-Date: Mon, 29 Feb 2016 14:20:15 +0000
-Subject: [PATCH] clk: bcm2835: expose raw clock-registers via debugfs
-
-For debugging purposes under some circumstance
-it helps to be able to see the actual clock registers.
-
-E.g: when looking at the clock divider it is helpful to
-see what the actual clock divider is.
-
-This patch exposes all the clock registers specific to each
-clock/pll/pll-divider via debugfs.
-
-Signed-off-by: Martin Sperl <kernel at martin.sperl.org>
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Acked-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 96bf9c69d5729781018a00f08e2ae395ec3346b4)
----
- drivers/clk/bcm/clk-bcm2835.c | 101 ++++++++++++++++++++++++++++++++++++++++++
- 1 file changed, 101 insertions(+)
-
---- a/drivers/clk/bcm/clk-bcm2835.c
-+++ b/drivers/clk/bcm/clk-bcm2835.c
-@@ -37,6 +37,7 @@
- #include <linux/clk-provider.h>
- #include <linux/clkdev.h>
- #include <linux/clk/bcm2835.h>
-+#include <linux/debugfs.h>
- #include <linux/module.h>
- #include <linux/of.h>
- #include <linux/platform_device.h>
-@@ -313,6 +314,27 @@ static inline u32 cprman_read(struct bcm
- return readl(cprman->regs + reg);
- }
-
-+static int bcm2835_debugfs_regset(struct bcm2835_cprman *cprman, u32 base,
-+ struct debugfs_reg32 *regs, size_t nregs,
-+ struct dentry *dentry)
-+{
-+ struct dentry *regdump;
-+ struct debugfs_regset32 *regset;
-+
-+ regset = devm_kzalloc(cprman->dev, sizeof(*regset), GFP_KERNEL);
-+ if (!regset)
-+ return -ENOMEM;
-+
-+ regset->regs = regs;
-+ regset->nregs = nregs;
-+ regset->base = cprman->regs + base;
-+
-+ regdump = debugfs_create_regset32("regdump", S_IRUGO, dentry,
-+ regset);
-+
-+ return regdump ? 0 : -ENOMEM;
-+}
-+
- /*
- * These are fixed clocks. They're probably not all root clocks and it may
- * be possible to turn them on and off but until this is mapped out better
-@@ -1044,6 +1066,36 @@ static int bcm2835_pll_set_rate(struct c
- return 0;
- }
-
-+static int bcm2835_pll_debug_init(struct clk_hw *hw,
-+ struct dentry *dentry)
-+{
-+ struct bcm2835_pll *pll = container_of(hw, struct bcm2835_pll, hw);
-+ struct bcm2835_cprman *cprman = pll->cprman;
-+ const struct bcm2835_pll_data *data = pll->data;
-+ struct debugfs_reg32 *regs;
-+
-+ regs = devm_kzalloc(cprman->dev, 7 * sizeof(*regs), GFP_KERNEL);
-+ if (!regs)
-+ return -ENOMEM;
-+
-+ regs[0].name = "cm_ctrl";
-+ regs[0].offset = data->cm_ctrl_reg;
-+ regs[1].name = "a2w_ctrl";
-+ regs[1].offset = data->a2w_ctrl_reg;
-+ regs[2].name = "frac";
-+ regs[2].offset = data->frac_reg;
-+ regs[3].name = "ana0";
-+ regs[3].offset = data->ana_reg_base + 0 * 4;
-+ regs[4].name = "ana1";
-+ regs[4].offset = data->ana_reg_base + 1 * 4;
-+ regs[5].name = "ana2";
-+ regs[5].offset = data->ana_reg_base + 2 * 4;
-+ regs[6].name = "ana3";
-+ regs[6].offset = data->ana_reg_base + 3 * 4;
-+
-+ return bcm2835_debugfs_regset(cprman, 0, regs, 7, dentry);
-+}
-+
- static const struct clk_ops bcm2835_pll_clk_ops = {
- .is_prepared = bcm2835_pll_is_on,
- .prepare = bcm2835_pll_on,
-@@ -1051,6 +1103,7 @@ static const struct clk_ops bcm2835_pll_
- .recalc_rate = bcm2835_pll_get_rate,
- .set_rate = bcm2835_pll_set_rate,
- .round_rate = bcm2835_pll_round_rate,
-+ .debug_init = bcm2835_pll_debug_init,
- };
-
- struct bcm2835_pll_divider {
-@@ -1153,6 +1206,26 @@ static int bcm2835_pll_divider_set_rate(
- return 0;
- }
-
-+static int bcm2835_pll_divider_debug_init(struct clk_hw *hw,
-+ struct dentry *dentry)
-+{
-+ struct bcm2835_pll_divider *divider = bcm2835_pll_divider_from_hw(hw);
-+ struct bcm2835_cprman *cprman = divider->cprman;
-+ const struct bcm2835_pll_divider_data *data = divider->data;
-+ struct debugfs_reg32 *regs;
-+
-+ regs = devm_kzalloc(cprman->dev, 7 * sizeof(*regs), GFP_KERNEL);
-+ if (!regs)
-+ return -ENOMEM;
-+
-+ regs[0].name = "cm";
-+ regs[0].offset = data->cm_reg;
-+ regs[1].name = "a2w";
-+ regs[1].offset = data->a2w_reg;
-+
-+ return bcm2835_debugfs_regset(cprman, 0, regs, 2, dentry);
-+}
-+
- static const struct clk_ops bcm2835_pll_divider_clk_ops = {
- .is_prepared = bcm2835_pll_divider_is_on,
- .prepare = bcm2835_pll_divider_on,
-@@ -1160,6 +1233,7 @@ static const struct clk_ops bcm2835_pll_
- .recalc_rate = bcm2835_pll_divider_get_rate,
- .set_rate = bcm2835_pll_divider_set_rate,
- .round_rate = bcm2835_pll_divider_round_rate,
-+ .debug_init = bcm2835_pll_divider_debug_init,
- };
-
- /*
-@@ -1401,6 +1475,31 @@ static u8 bcm2835_clock_get_parent(struc
- return (src & CM_SRC_MASK) >> CM_SRC_SHIFT;
- }
-
-+static struct debugfs_reg32 bcm2835_debugfs_clock_reg32[] = {
-+ {
-+ .name = "ctl",
-+ .offset = 0,
-+ },
-+ {
-+ .name = "div",
-+ .offset = 4,
-+ },
-+};
-+
-+static int bcm2835_clock_debug_init(struct clk_hw *hw,
-+ struct dentry *dentry)
-+{
-+ struct bcm2835_clock *clock = bcm2835_clock_from_hw(hw);
-+ struct bcm2835_cprman *cprman = clock->cprman;
-+ const struct bcm2835_clock_data *data = clock->data;
-+
-+ return bcm2835_debugfs_regset(
-+ cprman, data->ctl_reg,
-+ bcm2835_debugfs_clock_reg32,
-+ ARRAY_SIZE(bcm2835_debugfs_clock_reg32),
-+ dentry);
-+}
-+
- static const struct clk_ops bcm2835_clock_clk_ops = {
- .is_prepared = bcm2835_clock_is_on,
- .prepare = bcm2835_clock_on,
-@@ -1410,6 +1509,7 @@ static const struct clk_ops bcm2835_cloc
- .determine_rate = bcm2835_clock_determine_rate,
- .set_parent = bcm2835_clock_set_parent,
- .get_parent = bcm2835_clock_get_parent,
-+ .debug_init = bcm2835_clock_debug_init,
- };
-
- static int bcm2835_vpu_clock_is_on(struct clk_hw *hw)
-@@ -1428,6 +1528,7 @@ static const struct clk_ops bcm2835_vpu_
- .determine_rate = bcm2835_clock_determine_rate,
- .set_parent = bcm2835_clock_set_parent,
- .get_parent = bcm2835_clock_get_parent,
-+ .debug_init = bcm2835_clock_debug_init,
- };
-
- static struct clk *bcm2835_register_pll(struct bcm2835_cprman *cprman,
diff --git a/target/linux/brcm2708/patches-4.4/0259-clk-bcm2835-remove-use-of-BCM2835_CLOCK_COUNT-in-dri.patch b/target/linux/brcm2708/patches-4.4/0259-clk-bcm2835-remove-use-of-BCM2835_CLOCK_COUNT-in-dri.patch
deleted file mode 100644
index 02930bd..0000000
--- a/target/linux/brcm2708/patches-4.4/0259-clk-bcm2835-remove-use-of-BCM2835_CLOCK_COUNT-in-dri.patch
+++ /dev/null
@@ -1,236 +0,0 @@
-From 4552597dcdf2f17003addcd2157fd466aa513144 Mon Sep 17 00:00:00 2001
-From: Martin Sperl <kernel at martin.sperl.org>
-Date: Mon, 29 Feb 2016 12:51:41 +0000
-Subject: [PATCH] clk: bcm2835: remove use of BCM2835_CLOCK_COUNT in driver
-
-As the use of BCM2835_CLOCK_COUNT in
-include/dt-bindings/clock/bcm2835.h is frowned upon as
-it needs to get modified every time a new clock gets introduced
-this patch changes the clk-bcm2835 driver to use a different
-scheme for registration of clocks and pll, so that there
-is no more need for BCM2835_CLOCK_COUNT to be defined.
-
-Signed-off-by: Martin Sperl <kernel at martin.sperl.org>
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 56eb3a2ed9726961e1bcfa69d4a3f86d68f0eb52)
----
- drivers/clk/bcm/clk-bcm2835.c | 167 ++++++++++++++++++++----------------
- include/dt-bindings/clock/bcm2835.h | 2 -
- 2 files changed, 94 insertions(+), 75 deletions(-)
-
---- a/drivers/clk/bcm/clk-bcm2835.c
-+++ b/drivers/clk/bcm/clk-bcm2835.c
-@@ -301,7 +301,7 @@ struct bcm2835_cprman {
- const char *osc_name;
-
- struct clk_onecell_data onecell;
-- struct clk *clks[BCM2835_CLOCK_COUNT];
-+ struct clk *clks[];
- };
-
- static inline void cprman_write(struct bcm2835_cprman *cprman, u32 reg, u32 val)
-@@ -853,6 +853,25 @@ static const struct bcm2835_clock_data b
- .is_mash_clock = true,
- };
-
-+struct bcm2835_gate_data {
-+ const char *name;
-+ const char *parent;
-+
-+ u32 ctl_reg;
-+};
-+
-+/*
-+ * CM_PERIICTL (and CM_PERIACTL, CM_SYSCTL and CM_VPUCTL if
-+ * you have the debug bit set in the power manager, which we
-+ * don't bother exposing) are individual gates off of the
-+ * non-stop vpu clock.
-+ */
-+static const struct bcm2835_gate_data bcm2835_clock_peri_image_data = {
-+ .name = "peri_image",
-+ .parent = "vpu",
-+ .ctl_reg = CM_PERIICTL,
-+};
-+
- struct bcm2835_pll {
- struct clk_hw hw;
- struct bcm2835_cprman *cprman;
-@@ -1660,14 +1679,81 @@ static struct clk *bcm2835_register_cloc
- return devm_clk_register(cprman->dev, &clock->hw);
- }
-
-+static struct clk *bcm2835_register_gate(struct bcm2835_cprman *cprman,
-+ const struct bcm2835_gate_data *data)
-+{
-+ return clk_register_gate(cprman->dev, data->name, data->parent,
-+ CLK_IGNORE_UNUSED | CLK_SET_RATE_GATE,
-+ cprman->regs + data->ctl_reg,
-+ CM_GATE_BIT, 0, &cprman->regs_lock);
-+}
-+
-+typedef struct clk *(*bcm2835_clk_register)(struct bcm2835_cprman *cprman,
-+ const void *data);
-+struct bcm2835_clk_desc {
-+ bcm2835_clk_register clk_register;
-+ const void *data;
-+};
-+
-+#define _REGISTER(f, d) { .clk_register = (bcm2835_clk_register)f, \
-+ .data = d }
-+#define REGISTER_PLL(d) _REGISTER(&bcm2835_register_pll, d)
-+#define REGISTER_PLL_DIV(d) _REGISTER(&bcm2835_register_pll_divider, d)
-+#define REGISTER_CLK(d) _REGISTER(&bcm2835_register_clock, d)
-+#define REGISTER_GATE(d) _REGISTER(&bcm2835_register_gate, d)
-+
-+static const struct bcm2835_clk_desc clk_desc_array[] = {
-+ /* register PLL */
-+ [BCM2835_PLLA] = REGISTER_PLL(&bcm2835_plla_data),
-+ [BCM2835_PLLB] = REGISTER_PLL(&bcm2835_pllb_data),
-+ [BCM2835_PLLC] = REGISTER_PLL(&bcm2835_pllc_data),
-+ [BCM2835_PLLD] = REGISTER_PLL(&bcm2835_plld_data),
-+ [BCM2835_PLLH] = REGISTER_PLL(&bcm2835_pllh_data),
-+ /* the PLL dividers */
-+ [BCM2835_PLLA_CORE] = REGISTER_PLL_DIV(&bcm2835_plla_core_data),
-+ [BCM2835_PLLA_PER] = REGISTER_PLL_DIV(&bcm2835_plla_per_data),
-+ [BCM2835_PLLC_CORE0] = REGISTER_PLL_DIV(&bcm2835_pllc_core0_data),
-+ [BCM2835_PLLC_CORE1] = REGISTER_PLL_DIV(&bcm2835_pllc_core1_data),
-+ [BCM2835_PLLC_CORE2] = REGISTER_PLL_DIV(&bcm2835_pllc_core2_data),
-+ [BCM2835_PLLC_PER] = REGISTER_PLL_DIV(&bcm2835_pllc_per_data),
-+ [BCM2835_PLLD_CORE] = REGISTER_PLL_DIV(&bcm2835_plld_core_data),
-+ [BCM2835_PLLD_PER] = REGISTER_PLL_DIV(&bcm2835_plld_per_data),
-+ [BCM2835_PLLH_RCAL] = REGISTER_PLL_DIV(&bcm2835_pllh_rcal_data),
-+ [BCM2835_PLLH_AUX] = REGISTER_PLL_DIV(&bcm2835_pllh_aux_data),
-+ [BCM2835_PLLH_PIX] = REGISTER_PLL_DIV(&bcm2835_pllh_pix_data),
-+ /* the clocks */
-+ [BCM2835_CLOCK_TIMER] = REGISTER_CLK(&bcm2835_clock_timer_data),
-+ [BCM2835_CLOCK_OTP] = REGISTER_CLK(&bcm2835_clock_otp_data),
-+ [BCM2835_CLOCK_TSENS] = REGISTER_CLK(&bcm2835_clock_tsens_data),
-+ [BCM2835_CLOCK_VPU] = REGISTER_CLK(&bcm2835_clock_vpu_data),
-+ [BCM2835_CLOCK_V3D] = REGISTER_CLK(&bcm2835_clock_v3d_data),
-+ [BCM2835_CLOCK_ISP] = REGISTER_CLK(&bcm2835_clock_isp_data),
-+ [BCM2835_CLOCK_H264] = REGISTER_CLK(&bcm2835_clock_h264_data),
-+ [BCM2835_CLOCK_V3D] = REGISTER_CLK(&bcm2835_clock_v3d_data),
-+ [BCM2835_CLOCK_SDRAM] = REGISTER_CLK(&bcm2835_clock_sdram_data),
-+ [BCM2835_CLOCK_UART] = REGISTER_CLK(&bcm2835_clock_uart_data),
-+ [BCM2835_CLOCK_VEC] = REGISTER_CLK(&bcm2835_clock_vec_data),
-+ [BCM2835_CLOCK_HSM] = REGISTER_CLK(&bcm2835_clock_hsm_data),
-+ [BCM2835_CLOCK_EMMC] = REGISTER_CLK(&bcm2835_clock_emmc_data),
-+ [BCM2835_CLOCK_PWM] = REGISTER_CLK(&bcm2835_clock_pwm_data),
-+ /* the gates */
-+ [BCM2835_CLOCK_PERI_IMAGE] = REGISTER_GATE(
-+ &bcm2835_clock_peri_image_data),
-+};
-+
- static int bcm2835_clk_probe(struct platform_device *pdev)
- {
- struct device *dev = &pdev->dev;
- struct clk **clks;
- struct bcm2835_cprman *cprman;
- struct resource *res;
-+ const struct bcm2835_clk_desc *desc;
-+ const size_t asize = ARRAY_SIZE(clk_desc_array);
-+ size_t i;
-
-- cprman = devm_kzalloc(dev, sizeof(*cprman), GFP_KERNEL);
-+ cprman = devm_kzalloc(dev,
-+ sizeof(*cprman) + asize * sizeof(*clks),
-+ GFP_KERNEL);
- if (!cprman)
- return -ENOMEM;
-
-@@ -1684,80 +1770,15 @@ static int bcm2835_clk_probe(struct plat
-
- platform_set_drvdata(pdev, cprman);
-
-- cprman->onecell.clk_num = BCM2835_CLOCK_COUNT;
-+ cprman->onecell.clk_num = asize;
- cprman->onecell.clks = cprman->clks;
- clks = cprman->clks;
-
-- clks[BCM2835_PLLA] = bcm2835_register_pll(cprman, &bcm2835_plla_data);
-- clks[BCM2835_PLLB] = bcm2835_register_pll(cprman, &bcm2835_pllb_data);
-- clks[BCM2835_PLLC] = bcm2835_register_pll(cprman, &bcm2835_pllc_data);
-- clks[BCM2835_PLLD] = bcm2835_register_pll(cprman, &bcm2835_plld_data);
-- clks[BCM2835_PLLH] = bcm2835_register_pll(cprman, &bcm2835_pllh_data);
--
-- clks[BCM2835_PLLA_CORE] =
-- bcm2835_register_pll_divider(cprman, &bcm2835_plla_core_data);
-- clks[BCM2835_PLLA_PER] =
-- bcm2835_register_pll_divider(cprman, &bcm2835_plla_per_data);
-- clks[BCM2835_PLLC_CORE0] =
-- bcm2835_register_pll_divider(cprman, &bcm2835_pllc_core0_data);
-- clks[BCM2835_PLLC_CORE1] =
-- bcm2835_register_pll_divider(cprman, &bcm2835_pllc_core1_data);
-- clks[BCM2835_PLLC_CORE2] =
-- bcm2835_register_pll_divider(cprman, &bcm2835_pllc_core2_data);
-- clks[BCM2835_PLLC_PER] =
-- bcm2835_register_pll_divider(cprman, &bcm2835_pllc_per_data);
-- clks[BCM2835_PLLD_CORE] =
-- bcm2835_register_pll_divider(cprman, &bcm2835_plld_core_data);
-- clks[BCM2835_PLLD_PER] =
-- bcm2835_register_pll_divider(cprman, &bcm2835_plld_per_data);
-- clks[BCM2835_PLLH_RCAL] =
-- bcm2835_register_pll_divider(cprman, &bcm2835_pllh_rcal_data);
-- clks[BCM2835_PLLH_AUX] =
-- bcm2835_register_pll_divider(cprman, &bcm2835_pllh_aux_data);
-- clks[BCM2835_PLLH_PIX] =
-- bcm2835_register_pll_divider(cprman, &bcm2835_pllh_pix_data);
--
-- clks[BCM2835_CLOCK_TIMER] =
-- bcm2835_register_clock(cprman, &bcm2835_clock_timer_data);
-- clks[BCM2835_CLOCK_OTP] =
-- bcm2835_register_clock(cprman, &bcm2835_clock_otp_data);
-- clks[BCM2835_CLOCK_TSENS] =
-- bcm2835_register_clock(cprman, &bcm2835_clock_tsens_data);
-- clks[BCM2835_CLOCK_VPU] =
-- bcm2835_register_clock(cprman, &bcm2835_clock_vpu_data);
-- clks[BCM2835_CLOCK_V3D] =
-- bcm2835_register_clock(cprman, &bcm2835_clock_v3d_data);
-- clks[BCM2835_CLOCK_ISP] =
-- bcm2835_register_clock(cprman, &bcm2835_clock_isp_data);
-- clks[BCM2835_CLOCK_H264] =
-- bcm2835_register_clock(cprman, &bcm2835_clock_h264_data);
-- clks[BCM2835_CLOCK_V3D] =
-- bcm2835_register_clock(cprman, &bcm2835_clock_v3d_data);
-- clks[BCM2835_CLOCK_SDRAM] =
-- bcm2835_register_clock(cprman, &bcm2835_clock_sdram_data);
-- clks[BCM2835_CLOCK_UART] =
-- bcm2835_register_clock(cprman, &bcm2835_clock_uart_data);
-- clks[BCM2835_CLOCK_VEC] =
-- bcm2835_register_clock(cprman, &bcm2835_clock_vec_data);
-- clks[BCM2835_CLOCK_HSM] =
-- bcm2835_register_clock(cprman, &bcm2835_clock_hsm_data);
-- clks[BCM2835_CLOCK_EMMC] =
-- bcm2835_register_clock(cprman, &bcm2835_clock_emmc_data);
--
-- /*
-- * CM_PERIICTL (and CM_PERIACTL, CM_SYSCTL and CM_VPUCTL if
-- * you have the debug bit set in the power manager, which we
-- * don't bother exposing) are individual gates off of the
-- * non-stop vpu clock.
-- */
-- clks[BCM2835_CLOCK_PERI_IMAGE] =
-- clk_register_gate(dev, "peri_image", "vpu",
-- CLK_IGNORE_UNUSED | CLK_SET_RATE_GATE,
-- cprman->regs + CM_PERIICTL, CM_GATE_BIT,
-- 0, &cprman->regs_lock);
--
-- clks[BCM2835_CLOCK_PWM] =
-- bcm2835_register_clock(cprman, &bcm2835_clock_pwm_data);
-+ for (i = 0; i < asize; i++) {
-+ desc = &clk_desc_array[i];
-+ if (desc->clk_register && desc->data)
-+ clks[i] = desc->clk_register(cprman, desc->data);
-+ }
-
- return of_clk_add_provider(dev->of_node, of_clk_src_onecell_get,
- &cprman->onecell);
---- a/include/dt-bindings/clock/bcm2835.h
-+++ b/include/dt-bindings/clock/bcm2835.h
-@@ -44,5 +44,3 @@
- #define BCM2835_CLOCK_EMMC 28
- #define BCM2835_CLOCK_PERI_IMAGE 29
- #define BCM2835_CLOCK_PWM 30
--
--#define BCM2835_CLOCK_COUNT 31
diff --git a/target/linux/brcm2708/patches-4.4/0260-clk-bcm2835-reorganize-bcm2835_clock_array-assignmen.patch b/target/linux/brcm2708/patches-4.4/0260-clk-bcm2835-reorganize-bcm2835_clock_array-assignmen.patch
deleted file mode 100644
index 079db11..0000000
--- a/target/linux/brcm2708/patches-4.4/0260-clk-bcm2835-reorganize-bcm2835_clock_array-assignmen.patch
+++ /dev/null
@@ -1,925 +0,0 @@
-From 6efb6018b84fa3e5fefb69a097db05b6a0a6ba09 Mon Sep 17 00:00:00 2001
-From: Martin Sperl <kernel at martin.sperl.org>
-Date: Mon, 29 Feb 2016 12:51:42 +0000
-Subject: [PATCH] clk: bcm2835: reorganize bcm2835_clock_array assignment
-
-Reorganize bcm2835_clock_array so that there is no more
-need for separate bcm2835_*_data structures to be defined.
-Instead the required structures are generated inline via
-helper macros.
-
-To allow this to also work for pll alone it was required that
-the parent_pll was changed from a pointer to bcm2835_pll_data
-to the name of the pll instead.
-
-Signed-off-by: Martin Sperl <kernel at martin.sperl.org>
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 3b15afefbef9b5952e3d68ad73d93f981b9faca8)
----
- drivers/clk/bcm/clk-bcm2835.c | 852 +++++++++++++++++++-----------------------
- 1 file changed, 393 insertions(+), 459 deletions(-)
-
---- a/drivers/clk/bcm/clk-bcm2835.c
-+++ b/drivers/clk/bcm/clk-bcm2835.c
-@@ -418,115 +418,10 @@ static const struct bcm2835_pll_ana_bits
- .fb_prediv_mask = BIT(11),
- };
-
--/*
-- * PLLA is the auxiliary PLL, used to drive the CCP2 (Compact Camera
-- * Port 2) transmitter clock.
-- *
-- * It is in the PX LDO power domain, which is on when the AUDIO domain
-- * is on.
-- */
--static const struct bcm2835_pll_data bcm2835_plla_data = {
-- .name = "plla",
-- .cm_ctrl_reg = CM_PLLA,
-- .a2w_ctrl_reg = A2W_PLLA_CTRL,
-- .frac_reg = A2W_PLLA_FRAC,
-- .ana_reg_base = A2W_PLLA_ANA0,
-- .reference_enable_mask = A2W_XOSC_CTRL_PLLA_ENABLE,
-- .lock_mask = CM_LOCK_FLOCKA,
--
-- .ana = &bcm2835_ana_default,
--
-- .min_rate = 600000000u,
-- .max_rate = 2400000000u,
-- .max_fb_rate = BCM2835_MAX_FB_RATE,
--};
--
--/* PLLB is used for the ARM's clock. */
--static const struct bcm2835_pll_data bcm2835_pllb_data = {
-- .name = "pllb",
-- .cm_ctrl_reg = CM_PLLB,
-- .a2w_ctrl_reg = A2W_PLLB_CTRL,
-- .frac_reg = A2W_PLLB_FRAC,
-- .ana_reg_base = A2W_PLLB_ANA0,
-- .reference_enable_mask = A2W_XOSC_CTRL_PLLB_ENABLE,
-- .lock_mask = CM_LOCK_FLOCKB,
--
-- .ana = &bcm2835_ana_default,
--
-- .min_rate = 600000000u,
-- .max_rate = 3000000000u,
-- .max_fb_rate = BCM2835_MAX_FB_RATE,
--};
--
--/*
-- * PLLC is the core PLL, used to drive the core VPU clock.
-- *
-- * It is in the PX LDO power domain, which is on when the AUDIO domain
-- * is on.
--*/
--static const struct bcm2835_pll_data bcm2835_pllc_data = {
-- .name = "pllc",
-- .cm_ctrl_reg = CM_PLLC,
-- .a2w_ctrl_reg = A2W_PLLC_CTRL,
-- .frac_reg = A2W_PLLC_FRAC,
-- .ana_reg_base = A2W_PLLC_ANA0,
-- .reference_enable_mask = A2W_XOSC_CTRL_PLLC_ENABLE,
-- .lock_mask = CM_LOCK_FLOCKC,
--
-- .ana = &bcm2835_ana_default,
--
-- .min_rate = 600000000u,
-- .max_rate = 3000000000u,
-- .max_fb_rate = BCM2835_MAX_FB_RATE,
--};
--
--/*
-- * PLLD is the display PLL, used to drive DSI display panels.
-- *
-- * It is in the PX LDO power domain, which is on when the AUDIO domain
-- * is on.
-- */
--static const struct bcm2835_pll_data bcm2835_plld_data = {
-- .name = "plld",
-- .cm_ctrl_reg = CM_PLLD,
-- .a2w_ctrl_reg = A2W_PLLD_CTRL,
-- .frac_reg = A2W_PLLD_FRAC,
-- .ana_reg_base = A2W_PLLD_ANA0,
-- .reference_enable_mask = A2W_XOSC_CTRL_DDR_ENABLE,
-- .lock_mask = CM_LOCK_FLOCKD,
--
-- .ana = &bcm2835_ana_default,
--
-- .min_rate = 600000000u,
-- .max_rate = 2400000000u,
-- .max_fb_rate = BCM2835_MAX_FB_RATE,
--};
--
--/*
-- * PLLH is used to supply the pixel clock or the AUX clock for the TV
-- * encoder.
-- *
-- * It is in the HDMI power domain.
-- */
--static const struct bcm2835_pll_data bcm2835_pllh_data = {
-- "pllh",
-- .cm_ctrl_reg = CM_PLLH,
-- .a2w_ctrl_reg = A2W_PLLH_CTRL,
-- .frac_reg = A2W_PLLH_FRAC,
-- .ana_reg_base = A2W_PLLH_ANA0,
-- .reference_enable_mask = A2W_XOSC_CTRL_PLLC_ENABLE,
-- .lock_mask = CM_LOCK_FLOCKH,
--
-- .ana = &bcm2835_ana_pllh,
--
-- .min_rate = 600000000u,
-- .max_rate = 3000000000u,
-- .max_fb_rate = BCM2835_MAX_FB_RATE,
--};
--
- struct bcm2835_pll_divider_data {
- const char *name;
-- const struct bcm2835_pll_data *source_pll;
-+ const char *source_pll;
-+
- u32 cm_reg;
- u32 a2w_reg;
-
-@@ -535,124 +430,6 @@ struct bcm2835_pll_divider_data {
- u32 fixed_divider;
- };
-
--static const struct bcm2835_pll_divider_data bcm2835_plla_core_data = {
-- .name = "plla_core",
-- .source_pll = &bcm2835_plla_data,
-- .cm_reg = CM_PLLA,
-- .a2w_reg = A2W_PLLA_CORE,
-- .load_mask = CM_PLLA_LOADCORE,
-- .hold_mask = CM_PLLA_HOLDCORE,
-- .fixed_divider = 1,
--};
--
--static const struct bcm2835_pll_divider_data bcm2835_plla_per_data = {
-- .name = "plla_per",
-- .source_pll = &bcm2835_plla_data,
-- .cm_reg = CM_PLLA,
-- .a2w_reg = A2W_PLLA_PER,
-- .load_mask = CM_PLLA_LOADPER,
-- .hold_mask = CM_PLLA_HOLDPER,
-- .fixed_divider = 1,
--};
--
--static const struct bcm2835_pll_divider_data bcm2835_pllb_arm_data = {
-- .name = "pllb_arm",
-- .source_pll = &bcm2835_pllb_data,
-- .cm_reg = CM_PLLB,
-- .a2w_reg = A2W_PLLB_ARM,
-- .load_mask = CM_PLLB_LOADARM,
-- .hold_mask = CM_PLLB_HOLDARM,
-- .fixed_divider = 1,
--};
--
--static const struct bcm2835_pll_divider_data bcm2835_pllc_core0_data = {
-- .name = "pllc_core0",
-- .source_pll = &bcm2835_pllc_data,
-- .cm_reg = CM_PLLC,
-- .a2w_reg = A2W_PLLC_CORE0,
-- .load_mask = CM_PLLC_LOADCORE0,
-- .hold_mask = CM_PLLC_HOLDCORE0,
-- .fixed_divider = 1,
--};
--
--static const struct bcm2835_pll_divider_data bcm2835_pllc_core1_data = {
-- .name = "pllc_core1", .source_pll = &bcm2835_pllc_data,
-- .cm_reg = CM_PLLC, A2W_PLLC_CORE1,
-- .load_mask = CM_PLLC_LOADCORE1,
-- .hold_mask = CM_PLLC_HOLDCORE1,
-- .fixed_divider = 1,
--};
--
--static const struct bcm2835_pll_divider_data bcm2835_pllc_core2_data = {
-- .name = "pllc_core2",
-- .source_pll = &bcm2835_pllc_data,
-- .cm_reg = CM_PLLC,
-- .a2w_reg = A2W_PLLC_CORE2,
-- .load_mask = CM_PLLC_LOADCORE2,
-- .hold_mask = CM_PLLC_HOLDCORE2,
-- .fixed_divider = 1,
--};
--
--static const struct bcm2835_pll_divider_data bcm2835_pllc_per_data = {
-- .name = "pllc_per",
-- .source_pll = &bcm2835_pllc_data,
-- .cm_reg = CM_PLLC,
-- .a2w_reg = A2W_PLLC_PER,
-- .load_mask = CM_PLLC_LOADPER,
-- .hold_mask = CM_PLLC_HOLDPER,
-- .fixed_divider = 1,
--};
--
--static const struct bcm2835_pll_divider_data bcm2835_plld_core_data = {
-- .name = "plld_core",
-- .source_pll = &bcm2835_plld_data,
-- .cm_reg = CM_PLLD,
-- .a2w_reg = A2W_PLLD_CORE,
-- .load_mask = CM_PLLD_LOADCORE,
-- .hold_mask = CM_PLLD_HOLDCORE,
-- .fixed_divider = 1,
--};
--
--static const struct bcm2835_pll_divider_data bcm2835_plld_per_data = {
-- .name = "plld_per",
-- .source_pll = &bcm2835_plld_data,
-- .cm_reg = CM_PLLD,
-- .a2w_reg = A2W_PLLD_PER,
-- .load_mask = CM_PLLD_LOADPER,
-- .hold_mask = CM_PLLD_HOLDPER,
-- .fixed_divider = 1,
--};
--
--static const struct bcm2835_pll_divider_data bcm2835_pllh_rcal_data = {
-- .name = "pllh_rcal",
-- .source_pll = &bcm2835_pllh_data,
-- .cm_reg = CM_PLLH,
-- .a2w_reg = A2W_PLLH_RCAL,
-- .load_mask = CM_PLLH_LOADRCAL,
-- .hold_mask = 0,
-- .fixed_divider = 10,
--};
--
--static const struct bcm2835_pll_divider_data bcm2835_pllh_aux_data = {
-- .name = "pllh_aux",
-- .source_pll = &bcm2835_pllh_data,
-- .cm_reg = CM_PLLH,
-- .a2w_reg = A2W_PLLH_AUX,
-- .load_mask = CM_PLLH_LOADAUX,
-- .hold_mask = 0,
-- .fixed_divider = 10,
--};
--
--static const struct bcm2835_pll_divider_data bcm2835_pllh_pix_data = {
-- .name = "pllh_pix",
-- .source_pll = &bcm2835_pllh_data,
-- .cm_reg = CM_PLLH,
-- .a2w_reg = A2W_PLLH_PIX,
-- .load_mask = CM_PLLH_LOADPIX,
-- .hold_mask = 0,
-- .fixed_divider = 10,
--};
--
- struct bcm2835_clock_data {
- const char *name;
-
-@@ -671,188 +448,6 @@ struct bcm2835_clock_data {
- bool is_mash_clock;
- };
-
--static const char *const bcm2835_clock_per_parents[] = {
-- "gnd",
-- "xosc",
-- "testdebug0",
-- "testdebug1",
-- "plla_per",
-- "pllc_per",
-- "plld_per",
-- "pllh_aux",
--};
--
--static const char *const bcm2835_clock_vpu_parents[] = {
-- "gnd",
-- "xosc",
-- "testdebug0",
-- "testdebug1",
-- "plla_core",
-- "pllc_core0",
-- "plld_core",
-- "pllh_aux",
-- "pllc_core1",
-- "pllc_core2",
--};
--
--static const char *const bcm2835_clock_osc_parents[] = {
-- "gnd",
-- "xosc",
-- "testdebug0",
-- "testdebug1"
--};
--
--/*
-- * Used for a 1Mhz clock for the system clocksource, and also used by
-- * the watchdog timer and the camera pulse generator.
-- */
--static const struct bcm2835_clock_data bcm2835_clock_timer_data = {
-- .name = "timer",
-- .num_mux_parents = ARRAY_SIZE(bcm2835_clock_osc_parents),
-- .parents = bcm2835_clock_osc_parents,
-- .ctl_reg = CM_TIMERCTL,
-- .div_reg = CM_TIMERDIV,
-- .int_bits = 6,
-- .frac_bits = 12,
--};
--
--/* One Time Programmable Memory clock. Maximum 10Mhz. */
--static const struct bcm2835_clock_data bcm2835_clock_otp_data = {
-- .name = "otp",
-- .num_mux_parents = ARRAY_SIZE(bcm2835_clock_osc_parents),
-- .parents = bcm2835_clock_osc_parents,
-- .ctl_reg = CM_OTPCTL,
-- .div_reg = CM_OTPDIV,
-- .int_bits = 4,
-- .frac_bits = 0,
--};
--
--/*
-- * VPU clock. This doesn't have an enable bit, since it drives the
-- * bus for everything else, and is special so it doesn't need to be
-- * gated for rate changes. It is also known as "clk_audio" in various
-- * hardware documentation.
-- */
--static const struct bcm2835_clock_data bcm2835_clock_vpu_data = {
-- .name = "vpu",
-- .num_mux_parents = ARRAY_SIZE(bcm2835_clock_vpu_parents),
-- .parents = bcm2835_clock_vpu_parents,
-- .ctl_reg = CM_VPUCTL,
-- .div_reg = CM_VPUDIV,
-- .int_bits = 12,
-- .frac_bits = 8,
-- .is_vpu_clock = true,
--};
--
--static const struct bcm2835_clock_data bcm2835_clock_v3d_data = {
-- .name = "v3d",
-- .num_mux_parents = ARRAY_SIZE(bcm2835_clock_vpu_parents),
-- .parents = bcm2835_clock_vpu_parents,
-- .ctl_reg = CM_V3DCTL,
-- .div_reg = CM_V3DDIV,
-- .int_bits = 4,
-- .frac_bits = 8,
--};
--
--static const struct bcm2835_clock_data bcm2835_clock_isp_data = {
-- .name = "isp",
-- .num_mux_parents = ARRAY_SIZE(bcm2835_clock_vpu_parents),
-- .parents = bcm2835_clock_vpu_parents,
-- .ctl_reg = CM_ISPCTL,
-- .div_reg = CM_ISPDIV,
-- .int_bits = 4,
-- .frac_bits = 8,
--};
--
--static const struct bcm2835_clock_data bcm2835_clock_h264_data = {
-- .name = "h264",
-- .num_mux_parents = ARRAY_SIZE(bcm2835_clock_vpu_parents),
-- .parents = bcm2835_clock_vpu_parents,
-- .ctl_reg = CM_H264CTL,
-- .div_reg = CM_H264DIV,
-- .int_bits = 4,
-- .frac_bits = 8,
--};
--
--/* TV encoder clock. Only operating frequency is 108Mhz. */
--static const struct bcm2835_clock_data bcm2835_clock_vec_data = {
-- .name = "vec",
-- .num_mux_parents = ARRAY_SIZE(bcm2835_clock_per_parents),
-- .parents = bcm2835_clock_per_parents,
-- .ctl_reg = CM_VECCTL,
-- .div_reg = CM_VECDIV,
-- .int_bits = 4,
-- .frac_bits = 0,
--};
--
--static const struct bcm2835_clock_data bcm2835_clock_uart_data = {
-- .name = "uart",
-- .num_mux_parents = ARRAY_SIZE(bcm2835_clock_per_parents),
-- .parents = bcm2835_clock_per_parents,
-- .ctl_reg = CM_UARTCTL,
-- .div_reg = CM_UARTDIV,
-- .int_bits = 10,
-- .frac_bits = 12,
--};
--
--/* HDMI state machine */
--static const struct bcm2835_clock_data bcm2835_clock_hsm_data = {
-- .name = "hsm",
-- .num_mux_parents = ARRAY_SIZE(bcm2835_clock_per_parents),
-- .parents = bcm2835_clock_per_parents,
-- .ctl_reg = CM_HSMCTL,
-- .div_reg = CM_HSMDIV,
-- .int_bits = 4,
-- .frac_bits = 8,
--};
--
--/*
-- * Secondary SDRAM clock. Used for low-voltage modes when the PLL in
-- * the SDRAM controller can't be used.
-- */
--static const struct bcm2835_clock_data bcm2835_clock_sdram_data = {
-- .name = "sdram",
-- .num_mux_parents = ARRAY_SIZE(bcm2835_clock_vpu_parents),
-- .parents = bcm2835_clock_vpu_parents,
-- .ctl_reg = CM_SDCCTL,
-- .div_reg = CM_SDCDIV,
-- .int_bits = 6,
-- .frac_bits = 0,
--};
--
--/* Clock for the temperature sensor. Generally run at 2Mhz, max 5Mhz. */
--static const struct bcm2835_clock_data bcm2835_clock_tsens_data = {
-- .name = "tsens",
-- .num_mux_parents = ARRAY_SIZE(bcm2835_clock_osc_parents),
-- .parents = bcm2835_clock_osc_parents,
-- .ctl_reg = CM_TSENSCTL,
-- .div_reg = CM_TSENSDIV,
-- .int_bits = 5,
-- .frac_bits = 0,
--};
--
--/* Arasan EMMC clock */
--static const struct bcm2835_clock_data bcm2835_clock_emmc_data = {
-- .name = "emmc",
-- .num_mux_parents = ARRAY_SIZE(bcm2835_clock_per_parents),
-- .parents = bcm2835_clock_per_parents,
-- .ctl_reg = CM_EMMCCTL,
-- .div_reg = CM_EMMCDIV,
-- .int_bits = 4,
-- .frac_bits = 8,
--};
--
--static const struct bcm2835_clock_data bcm2835_clock_pwm_data = {
-- .name = "pwm",
-- .num_mux_parents = ARRAY_SIZE(bcm2835_clock_per_parents),
-- .parents = bcm2835_clock_per_parents,
-- .ctl_reg = CM_PWMCTL,
-- .div_reg = CM_PWMDIV,
-- .int_bits = 12,
-- .frac_bits = 12,
-- .is_mash_clock = true,
--};
--
- struct bcm2835_gate_data {
- const char *name;
- const char *parent;
-@@ -860,18 +455,6 @@ struct bcm2835_gate_data {
- u32 ctl_reg;
- };
-
--/*
-- * CM_PERIICTL (and CM_PERIACTL, CM_SYSCTL and CM_VPUCTL if
-- * you have the debug bit set in the power manager, which we
-- * don't bother exposing) are individual gates off of the
-- * non-stop vpu clock.
-- */
--static const struct bcm2835_gate_data bcm2835_clock_peri_image_data = {
-- .name = "peri_image",
-- .parent = "vpu",
-- .ctl_reg = CM_PERIICTL,
--};
--
- struct bcm2835_pll {
- struct clk_hw hw;
- struct bcm2835_cprman *cprman;
-@@ -1596,7 +1179,7 @@ bcm2835_register_pll_divider(struct bcm2
-
- memset(&init, 0, sizeof(init));
-
-- init.parent_names = &data->source_pll->name;
-+ init.parent_names = &data->source_pll;
- init.num_parents = 1;
- init.name = divider_name;
- init.ops = &bcm2835_pll_divider_clk_ops;
-@@ -1695,50 +1278,401 @@ struct bcm2835_clk_desc {
- const void *data;
- };
-
--#define _REGISTER(f, d) { .clk_register = (bcm2835_clk_register)f, \
-- .data = d }
--#define REGISTER_PLL(d) _REGISTER(&bcm2835_register_pll, d)
--#define REGISTER_PLL_DIV(d) _REGISTER(&bcm2835_register_pll_divider, d)
--#define REGISTER_CLK(d) _REGISTER(&bcm2835_register_clock, d)
--#define REGISTER_GATE(d) _REGISTER(&bcm2835_register_gate, d)
-+/* assignment helper macros for different clock types */
-+#define _REGISTER(f, ...) { .clk_register = (bcm2835_clk_register)f, \
-+ .data = __VA_ARGS__ }
-+#define REGISTER_PLL(...) _REGISTER(&bcm2835_register_pll, \
-+ &(struct bcm2835_pll_data) \
-+ {__VA_ARGS__})
-+#define REGISTER_PLL_DIV(...) _REGISTER(&bcm2835_register_pll_divider, \
-+ &(struct bcm2835_pll_divider_data) \
-+ {__VA_ARGS__})
-+#define REGISTER_CLK(...) _REGISTER(&bcm2835_register_clock, \
-+ &(struct bcm2835_clock_data) \
-+ {__VA_ARGS__})
-+#define REGISTER_GATE(...) _REGISTER(&bcm2835_register_gate, \
-+ &(struct bcm2835_gate_data) \
-+ {__VA_ARGS__})
-+
-+/* parent mux arrays plus helper macros */
-+
-+/* main oscillator parent mux */
-+static const char *const bcm2835_clock_osc_parents[] = {
-+ "gnd",
-+ "xosc",
-+ "testdebug0",
-+ "testdebug1"
-+};
-+
-+#define REGISTER_OSC_CLK(...) REGISTER_CLK( \
-+ .num_mux_parents = ARRAY_SIZE(bcm2835_clock_osc_parents), \
-+ .parents = bcm2835_clock_osc_parents, \
-+ __VA_ARGS__)
-+
-+/* main peripherial parent mux */
-+static const char *const bcm2835_clock_per_parents[] = {
-+ "gnd",
-+ "xosc",
-+ "testdebug0",
-+ "testdebug1",
-+ "plla_per",
-+ "pllc_per",
-+ "plld_per",
-+ "pllh_aux",
-+};
-+
-+#define REGISTER_PER_CLK(...) REGISTER_CLK( \
-+ .num_mux_parents = ARRAY_SIZE(bcm2835_clock_per_parents), \
-+ .parents = bcm2835_clock_per_parents, \
-+ __VA_ARGS__)
-+
-+/* main vpu parent mux */
-+static const char *const bcm2835_clock_vpu_parents[] = {
-+ "gnd",
-+ "xosc",
-+ "testdebug0",
-+ "testdebug1",
-+ "plla_core",
-+ "pllc_core0",
-+ "plld_core",
-+ "pllh_aux",
-+ "pllc_core1",
-+ "pllc_core2",
-+};
-+
-+#define REGISTER_VPU_CLK(...) REGISTER_CLK( \
-+ .num_mux_parents = ARRAY_SIZE(bcm2835_clock_vpu_parents), \
-+ .parents = bcm2835_clock_vpu_parents, \
-+ __VA_ARGS__)
-
-+/*
-+ * the real definition of all the pll, pll_dividers and clocks
-+ * these make use of the above REGISTER_* macros
-+ */
- static const struct bcm2835_clk_desc clk_desc_array[] = {
-- /* register PLL */
-- [BCM2835_PLLA] = REGISTER_PLL(&bcm2835_plla_data),
-- [BCM2835_PLLB] = REGISTER_PLL(&bcm2835_pllb_data),
-- [BCM2835_PLLC] = REGISTER_PLL(&bcm2835_pllc_data),
-- [BCM2835_PLLD] = REGISTER_PLL(&bcm2835_plld_data),
-- [BCM2835_PLLH] = REGISTER_PLL(&bcm2835_pllh_data),
-- /* the PLL dividers */
-- [BCM2835_PLLA_CORE] = REGISTER_PLL_DIV(&bcm2835_plla_core_data),
-- [BCM2835_PLLA_PER] = REGISTER_PLL_DIV(&bcm2835_plla_per_data),
-- [BCM2835_PLLC_CORE0] = REGISTER_PLL_DIV(&bcm2835_pllc_core0_data),
-- [BCM2835_PLLC_CORE1] = REGISTER_PLL_DIV(&bcm2835_pllc_core1_data),
-- [BCM2835_PLLC_CORE2] = REGISTER_PLL_DIV(&bcm2835_pllc_core2_data),
-- [BCM2835_PLLC_PER] = REGISTER_PLL_DIV(&bcm2835_pllc_per_data),
-- [BCM2835_PLLD_CORE] = REGISTER_PLL_DIV(&bcm2835_plld_core_data),
-- [BCM2835_PLLD_PER] = REGISTER_PLL_DIV(&bcm2835_plld_per_data),
-- [BCM2835_PLLH_RCAL] = REGISTER_PLL_DIV(&bcm2835_pllh_rcal_data),
-- [BCM2835_PLLH_AUX] = REGISTER_PLL_DIV(&bcm2835_pllh_aux_data),
-- [BCM2835_PLLH_PIX] = REGISTER_PLL_DIV(&bcm2835_pllh_pix_data),
-+ /* the PLL + PLL dividers */
-+
-+ /*
-+ * PLLA is the auxiliary PLL, used to drive the CCP2
-+ * (Compact Camera Port 2) transmitter clock.
-+ *
-+ * It is in the PX LDO power domain, which is on when the
-+ * AUDIO domain is on.
-+ */
-+ [BCM2835_PLLA] = REGISTER_PLL(
-+ .name = "plla",
-+ .cm_ctrl_reg = CM_PLLA,
-+ .a2w_ctrl_reg = A2W_PLLA_CTRL,
-+ .frac_reg = A2W_PLLA_FRAC,
-+ .ana_reg_base = A2W_PLLA_ANA0,
-+ .reference_enable_mask = A2W_XOSC_CTRL_PLLA_ENABLE,
-+ .lock_mask = CM_LOCK_FLOCKA,
-+
-+ .ana = &bcm2835_ana_default,
-+
-+ .min_rate = 600000000u,
-+ .max_rate = 2400000000u,
-+ .max_fb_rate = BCM2835_MAX_FB_RATE),
-+ [BCM2835_PLLA_CORE] = REGISTER_PLL_DIV(
-+ .name = "plla_core",
-+ .source_pll = "plla",
-+ .cm_reg = CM_PLLA,
-+ .a2w_reg = A2W_PLLA_CORE,
-+ .load_mask = CM_PLLA_LOADCORE,
-+ .hold_mask = CM_PLLA_HOLDCORE,
-+ .fixed_divider = 1),
-+ [BCM2835_PLLA_PER] = REGISTER_PLL_DIV(
-+ .name = "plla_per",
-+ .source_pll = "plla",
-+ .cm_reg = CM_PLLA,
-+ .a2w_reg = A2W_PLLA_PER,
-+ .load_mask = CM_PLLA_LOADPER,
-+ .hold_mask = CM_PLLA_HOLDPER,
-+ .fixed_divider = 1),
-+
-+ /* PLLB is used for the ARM's clock. */
-+ [BCM2835_PLLB] = REGISTER_PLL(
-+ .name = "pllb",
-+ .cm_ctrl_reg = CM_PLLB,
-+ .a2w_ctrl_reg = A2W_PLLB_CTRL,
-+ .frac_reg = A2W_PLLB_FRAC,
-+ .ana_reg_base = A2W_PLLB_ANA0,
-+ .reference_enable_mask = A2W_XOSC_CTRL_PLLB_ENABLE,
-+ .lock_mask = CM_LOCK_FLOCKB,
-+
-+ .ana = &bcm2835_ana_default,
-+
-+ .min_rate = 600000000u,
-+ .max_rate = 3000000000u,
-+ .max_fb_rate = BCM2835_MAX_FB_RATE),
-+ [BCM2835_PLLB_ARM] = REGISTER_PLL_DIV(
-+ .name = "pllb_arm",
-+ .source_pll = "pllb",
-+ .cm_reg = CM_PLLB,
-+ .a2w_reg = A2W_PLLB_ARM,
-+ .load_mask = CM_PLLB_LOADARM,
-+ .hold_mask = CM_PLLB_HOLDARM,
-+ .fixed_divider = 1),
-+
-+ /*
-+ * PLLC is the core PLL, used to drive the core VPU clock.
-+ *
-+ * It is in the PX LDO power domain, which is on when the
-+ * AUDIO domain is on.
-+ */
-+ [BCM2835_PLLC] = REGISTER_PLL(
-+ .name = "pllc",
-+ .cm_ctrl_reg = CM_PLLC,
-+ .a2w_ctrl_reg = A2W_PLLC_CTRL,
-+ .frac_reg = A2W_PLLC_FRAC,
-+ .ana_reg_base = A2W_PLLC_ANA0,
-+ .reference_enable_mask = A2W_XOSC_CTRL_PLLC_ENABLE,
-+ .lock_mask = CM_LOCK_FLOCKC,
-+
-+ .ana = &bcm2835_ana_default,
-+
-+ .min_rate = 600000000u,
-+ .max_rate = 3000000000u,
-+ .max_fb_rate = BCM2835_MAX_FB_RATE),
-+ [BCM2835_PLLC_CORE0] = REGISTER_PLL_DIV(
-+ .name = "pllc_core0",
-+ .source_pll = "pllc",
-+ .cm_reg = CM_PLLC,
-+ .a2w_reg = A2W_PLLC_CORE0,
-+ .load_mask = CM_PLLC_LOADCORE0,
-+ .hold_mask = CM_PLLC_HOLDCORE0,
-+ .fixed_divider = 1),
-+ [BCM2835_PLLC_CORE1] = REGISTER_PLL_DIV(
-+ .name = "pllc_core1",
-+ .source_pll = "pllc",
-+ .cm_reg = CM_PLLC,
-+ .a2w_reg = A2W_PLLC_CORE1,
-+ .load_mask = CM_PLLC_LOADCORE1,
-+ .hold_mask = CM_PLLC_HOLDCORE1,
-+ .fixed_divider = 1),
-+ [BCM2835_PLLC_CORE2] = REGISTER_PLL_DIV(
-+ .name = "pllc_core2",
-+ .source_pll = "pllc",
-+ .cm_reg = CM_PLLC,
-+ .a2w_reg = A2W_PLLC_CORE2,
-+ .load_mask = CM_PLLC_LOADCORE2,
-+ .hold_mask = CM_PLLC_HOLDCORE2,
-+ .fixed_divider = 1),
-+ [BCM2835_PLLC_PER] = REGISTER_PLL_DIV(
-+ .name = "pllc_per",
-+ .source_pll = "pllc",
-+ .cm_reg = CM_PLLC,
-+ .a2w_reg = A2W_PLLC_PER,
-+ .load_mask = CM_PLLC_LOADPER,
-+ .hold_mask = CM_PLLC_HOLDPER,
-+ .fixed_divider = 1),
-+
-+ /*
-+ * PLLD is the display PLL, used to drive DSI display panels.
-+ *
-+ * It is in the PX LDO power domain, which is on when the
-+ * AUDIO domain is on.
-+ */
-+ [BCM2835_PLLD] = REGISTER_PLL(
-+ .name = "plld",
-+ .cm_ctrl_reg = CM_PLLD,
-+ .a2w_ctrl_reg = A2W_PLLD_CTRL,
-+ .frac_reg = A2W_PLLD_FRAC,
-+ .ana_reg_base = A2W_PLLD_ANA0,
-+ .reference_enable_mask = A2W_XOSC_CTRL_DDR_ENABLE,
-+ .lock_mask = CM_LOCK_FLOCKD,
-+
-+ .ana = &bcm2835_ana_default,
-+
-+ .min_rate = 600000000u,
-+ .max_rate = 2400000000u,
-+ .max_fb_rate = BCM2835_MAX_FB_RATE),
-+ [BCM2835_PLLD_CORE] = REGISTER_PLL_DIV(
-+ .name = "plld_core",
-+ .source_pll = "plld",
-+ .cm_reg = CM_PLLD,
-+ .a2w_reg = A2W_PLLD_CORE,
-+ .load_mask = CM_PLLD_LOADCORE,
-+ .hold_mask = CM_PLLD_HOLDCORE,
-+ .fixed_divider = 1),
-+ [BCM2835_PLLD_PER] = REGISTER_PLL_DIV(
-+ .name = "plld_per",
-+ .source_pll = "plld",
-+ .cm_reg = CM_PLLD,
-+ .a2w_reg = A2W_PLLD_PER,
-+ .load_mask = CM_PLLD_LOADPER,
-+ .hold_mask = CM_PLLD_HOLDPER,
-+ .fixed_divider = 1),
-+
-+ /*
-+ * PLLH is used to supply the pixel clock or the AUX clock for the
-+ * TV encoder.
-+ *
-+ * It is in the HDMI power domain.
-+ */
-+ [BCM2835_PLLH] = REGISTER_PLL(
-+ "pllh",
-+ .cm_ctrl_reg = CM_PLLH,
-+ .a2w_ctrl_reg = A2W_PLLH_CTRL,
-+ .frac_reg = A2W_PLLH_FRAC,
-+ .ana_reg_base = A2W_PLLH_ANA0,
-+ .reference_enable_mask = A2W_XOSC_CTRL_PLLC_ENABLE,
-+ .lock_mask = CM_LOCK_FLOCKH,
-+
-+ .ana = &bcm2835_ana_pllh,
-+
-+ .min_rate = 600000000u,
-+ .max_rate = 3000000000u,
-+ .max_fb_rate = BCM2835_MAX_FB_RATE),
-+ [BCM2835_PLLH_RCAL] = REGISTER_PLL_DIV(
-+ .name = "pllh_rcal",
-+ .source_pll = "pllh",
-+ .cm_reg = CM_PLLH,
-+ .a2w_reg = A2W_PLLH_RCAL,
-+ .load_mask = CM_PLLH_LOADRCAL,
-+ .hold_mask = 0,
-+ .fixed_divider = 10),
-+ [BCM2835_PLLH_AUX] = REGISTER_PLL_DIV(
-+ .name = "pllh_aux",
-+ .source_pll = "pllh",
-+ .cm_reg = CM_PLLH,
-+ .a2w_reg = A2W_PLLH_AUX,
-+ .load_mask = CM_PLLH_LOADAUX,
-+ .hold_mask = 0,
-+ .fixed_divider = 10),
-+ [BCM2835_PLLH_PIX] = REGISTER_PLL_DIV(
-+ .name = "pllh_pix",
-+ .source_pll = "pllh",
-+ .cm_reg = CM_PLLH,
-+ .a2w_reg = A2W_PLLH_PIX,
-+ .load_mask = CM_PLLH_LOADPIX,
-+ .hold_mask = 0,
-+ .fixed_divider = 10),
-+
- /* the clocks */
-- [BCM2835_CLOCK_TIMER] = REGISTER_CLK(&bcm2835_clock_timer_data),
-- [BCM2835_CLOCK_OTP] = REGISTER_CLK(&bcm2835_clock_otp_data),
-- [BCM2835_CLOCK_TSENS] = REGISTER_CLK(&bcm2835_clock_tsens_data),
-- [BCM2835_CLOCK_VPU] = REGISTER_CLK(&bcm2835_clock_vpu_data),
-- [BCM2835_CLOCK_V3D] = REGISTER_CLK(&bcm2835_clock_v3d_data),
-- [BCM2835_CLOCK_ISP] = REGISTER_CLK(&bcm2835_clock_isp_data),
-- [BCM2835_CLOCK_H264] = REGISTER_CLK(&bcm2835_clock_h264_data),
-- [BCM2835_CLOCK_V3D] = REGISTER_CLK(&bcm2835_clock_v3d_data),
-- [BCM2835_CLOCK_SDRAM] = REGISTER_CLK(&bcm2835_clock_sdram_data),
-- [BCM2835_CLOCK_UART] = REGISTER_CLK(&bcm2835_clock_uart_data),
-- [BCM2835_CLOCK_VEC] = REGISTER_CLK(&bcm2835_clock_vec_data),
-- [BCM2835_CLOCK_HSM] = REGISTER_CLK(&bcm2835_clock_hsm_data),
-- [BCM2835_CLOCK_EMMC] = REGISTER_CLK(&bcm2835_clock_emmc_data),
-- [BCM2835_CLOCK_PWM] = REGISTER_CLK(&bcm2835_clock_pwm_data),
-+
-+ /* clocks with oscillator parent mux */
-+
-+ /* One Time Programmable Memory clock. Maximum 10Mhz. */
-+ [BCM2835_CLOCK_OTP] = REGISTER_OSC_CLK(
-+ .name = "otp",
-+ .ctl_reg = CM_OTPCTL,
-+ .div_reg = CM_OTPDIV,
-+ .int_bits = 4,
-+ .frac_bits = 0),
-+ /*
-+ * Used for a 1Mhz clock for the system clocksource, and also used
-+ * bythe watchdog timer and the camera pulse generator.
-+ */
-+ [BCM2835_CLOCK_TIMER] = REGISTER_OSC_CLK(
-+ .name = "timer",
-+ .ctl_reg = CM_TIMERCTL,
-+ .div_reg = CM_TIMERDIV,
-+ .int_bits = 6,
-+ .frac_bits = 12),
-+ /*
-+ * Clock for the temperature sensor.
-+ * Generally run at 2Mhz, max 5Mhz.
-+ */
-+ [BCM2835_CLOCK_TSENS] = REGISTER_OSC_CLK(
-+ .name = "tsens",
-+ .ctl_reg = CM_TSENSCTL,
-+ .div_reg = CM_TSENSDIV,
-+ .int_bits = 5,
-+ .frac_bits = 0),
-+
-+ /* clocks with vpu parent mux */
-+ [BCM2835_CLOCK_H264] = REGISTER_VPU_CLK(
-+ .name = "h264",
-+ .ctl_reg = CM_H264CTL,
-+ .div_reg = CM_H264DIV,
-+ .int_bits = 4,
-+ .frac_bits = 8),
-+ [BCM2835_CLOCK_ISP] = REGISTER_VPU_CLK(
-+ .name = "isp",
-+ .ctl_reg = CM_ISPCTL,
-+ .div_reg = CM_ISPDIV,
-+ .int_bits = 4,
-+ .frac_bits = 8),
-+ /*
-+ * Secondary SDRAM clock. Used for low-voltage modes when the PLL
-+ * in the SDRAM controller can't be used.
-+ */
-+ [BCM2835_CLOCK_SDRAM] = REGISTER_VPU_CLK(
-+ .name = "sdram",
-+ .ctl_reg = CM_SDCCTL,
-+ .div_reg = CM_SDCDIV,
-+ .int_bits = 6,
-+ .frac_bits = 0),
-+ [BCM2835_CLOCK_V3D] = REGISTER_VPU_CLK(
-+ .name = "v3d",
-+ .ctl_reg = CM_V3DCTL,
-+ .div_reg = CM_V3DDIV,
-+ .int_bits = 4,
-+ .frac_bits = 8),
-+ /*
-+ * VPU clock. This doesn't have an enable bit, since it drives
-+ * the bus for everything else, and is special so it doesn't need
-+ * to be gated for rate changes. It is also known as "clk_audio"
-+ * in various hardware documentation.
-+ */
-+ [BCM2835_CLOCK_VPU] = REGISTER_VPU_CLK(
-+ .name = "vpu",
-+ .ctl_reg = CM_VPUCTL,
-+ .div_reg = CM_VPUDIV,
-+ .int_bits = 12,
-+ .frac_bits = 8,
-+ .is_vpu_clock = true),
-+
-+ /* clocks with per parent mux */
-+
-+ /* Arasan EMMC clock */
-+ [BCM2835_CLOCK_EMMC] = REGISTER_PER_CLK(
-+ .name = "emmc",
-+ .ctl_reg = CM_EMMCCTL,
-+ .div_reg = CM_EMMCDIV,
-+ .int_bits = 4,
-+ .frac_bits = 8),
-+ /* HDMI state machine */
-+ [BCM2835_CLOCK_HSM] = REGISTER_PER_CLK(
-+ .name = "hsm",
-+ .ctl_reg = CM_HSMCTL,
-+ .div_reg = CM_HSMDIV,
-+ .int_bits = 4,
-+ .frac_bits = 8),
-+ [BCM2835_CLOCK_PWM] = REGISTER_PER_CLK(
-+ .name = "pwm",
-+ .ctl_reg = CM_PWMCTL,
-+ .div_reg = CM_PWMDIV,
-+ .int_bits = 12,
-+ .frac_bits = 12,
-+ .is_mash_clock = true),
-+ [BCM2835_CLOCK_UART] = REGISTER_PER_CLK(
-+ .name = "uart",
-+ .ctl_reg = CM_UARTCTL,
-+ .div_reg = CM_UARTDIV,
-+ .int_bits = 10,
-+ .frac_bits = 12),
-+ /* TV encoder clock. Only operating frequency is 108Mhz. */
-+ [BCM2835_CLOCK_VEC] = REGISTER_PER_CLK(
-+ .name = "vec",
-+ .ctl_reg = CM_VECCTL,
-+ .div_reg = CM_VECDIV,
-+ .int_bits = 4,
-+ .frac_bits = 0),
-+
- /* the gates */
-+
-+ /*
-+ * CM_PERIICTL (and CM_PERIACTL, CM_SYSCTL and CM_VPUCTL if
-+ * you have the debug bit set in the power manager, which we
-+ * don't bother exposing) are individual gates off of the
-+ * non-stop vpu clock.
-+ */
- [BCM2835_CLOCK_PERI_IMAGE] = REGISTER_GATE(
-- &bcm2835_clock_peri_image_data),
-+ .name = "peri_image",
-+ .parent = "vpu",
-+ .ctl_reg = CM_PERIICTL),
- };
-
- static int bcm2835_clk_probe(struct platform_device *pdev)
diff --git a/target/linux/brcm2708/patches-4.4/0261-clk-bcm2835-enable-management-of-PCM-clock.patch b/target/linux/brcm2708/patches-4.4/0261-clk-bcm2835-enable-management-of-PCM-clock.patch
deleted file mode 100644
index 9309272..0000000
--- a/target/linux/brcm2708/patches-4.4/0261-clk-bcm2835-enable-management-of-PCM-clock.patch
+++ /dev/null
@@ -1,40 +0,0 @@
-From 32639fed421640aaeda9e5f102264895a8a9f42c Mon Sep 17 00:00:00 2001
-From: Martin Sperl <kernel at martin.sperl.org>
-Date: Mon, 29 Feb 2016 12:51:43 +0000
-Subject: [PATCH] clk: bcm2835: enable management of PCM clock
-
-Enable the PCM clock in the SOC, which is used by the
-bcm2835-i2s driver.
-
-Signed-off-by: Martin Sperl <kernel at martin.sperl.org>
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 33b689600f43094a9316a1b582f2286d17bc737b)
----
- drivers/clk/bcm/clk-bcm2835.c | 7 +++++++
- include/dt-bindings/clock/bcm2835.h | 1 +
- 2 files changed, 8 insertions(+)
-
---- a/drivers/clk/bcm/clk-bcm2835.c
-+++ b/drivers/clk/bcm/clk-bcm2835.c
-@@ -1640,6 +1640,13 @@ static const struct bcm2835_clk_desc clk
- .div_reg = CM_HSMDIV,
- .int_bits = 4,
- .frac_bits = 8),
-+ [BCM2835_CLOCK_PCM] = REGISTER_PER_CLK(
-+ .name = "pcm",
-+ .ctl_reg = CM_PCMCTL,
-+ .div_reg = CM_PCMDIV,
-+ .int_bits = 12,
-+ .frac_bits = 12,
-+ .is_mash_clock = true),
- [BCM2835_CLOCK_PWM] = REGISTER_PER_CLK(
- .name = "pwm",
- .ctl_reg = CM_PWMCTL,
---- a/include/dt-bindings/clock/bcm2835.h
-+++ b/include/dt-bindings/clock/bcm2835.h
-@@ -44,3 +44,4 @@
- #define BCM2835_CLOCK_EMMC 28
- #define BCM2835_CLOCK_PERI_IMAGE 29
- #define BCM2835_CLOCK_PWM 30
-+#define BCM2835_CLOCK_PCM 31
diff --git a/target/linux/brcm2708/patches-4.4/0262-clk-bcm2835-add-missing-PLL-clock-dividers.patch b/target/linux/brcm2708/patches-4.4/0262-clk-bcm2835-add-missing-PLL-clock-dividers.patch
deleted file mode 100644
index 20a9cd8..0000000
--- a/target/linux/brcm2708/patches-4.4/0262-clk-bcm2835-add-missing-PLL-clock-dividers.patch
+++ /dev/null
@@ -1,73 +0,0 @@
-From df502f9589fb2d25ef93906adfb2ce2f8349397d Mon Sep 17 00:00:00 2001
-From: Martin Sperl <kernel at martin.sperl.org>
-Date: Mon, 29 Feb 2016 15:43:56 +0000
-Subject: [PATCH] clk: bcm2835: add missing PLL clock dividers
-
-Signed-off-by: Martin Sperl <kernel at martin.sperl.org>
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 728436956aa172b24a3212295f8b53feb6479f32)
----
- drivers/clk/bcm/clk-bcm2835.c | 32 ++++++++++++++++++++++++++++++++
- include/dt-bindings/clock/bcm2835.h | 5 +++++
- 2 files changed, 37 insertions(+)
-
---- a/drivers/clk/bcm/clk-bcm2835.c
-+++ b/drivers/clk/bcm/clk-bcm2835.c
-@@ -1389,6 +1389,22 @@ static const struct bcm2835_clk_desc clk
- .load_mask = CM_PLLA_LOADPER,
- .hold_mask = CM_PLLA_HOLDPER,
- .fixed_divider = 1),
-+ [BCM2835_PLLA_DSI0] = REGISTER_PLL_DIV(
-+ .name = "plla_dsi0",
-+ .source_pll = "plla",
-+ .cm_reg = CM_PLLA,
-+ .a2w_reg = A2W_PLLA_DSI0,
-+ .load_mask = CM_PLLA_LOADDSI0,
-+ .hold_mask = CM_PLLA_HOLDDSI0,
-+ .fixed_divider = 1),
-+ [BCM2835_PLLA_CCP2] = REGISTER_PLL_DIV(
-+ .name = "plla_ccp2",
-+ .source_pll = "plla",
-+ .cm_reg = CM_PLLA,
-+ .a2w_reg = A2W_PLLA_CCP2,
-+ .load_mask = CM_PLLA_LOADCCP2,
-+ .hold_mask = CM_PLLA_HOLDCCP2,
-+ .fixed_divider = 1),
-
- /* PLLB is used for the ARM's clock. */
- [BCM2835_PLLB] = REGISTER_PLL(
-@@ -1503,6 +1519,22 @@ static const struct bcm2835_clk_desc clk
- .load_mask = CM_PLLD_LOADPER,
- .hold_mask = CM_PLLD_HOLDPER,
- .fixed_divider = 1),
-+ [BCM2835_PLLD_DSI0] = REGISTER_PLL_DIV(
-+ .name = "plld_dsi0",
-+ .source_pll = "plld",
-+ .cm_reg = CM_PLLD,
-+ .a2w_reg = A2W_PLLD_DSI0,
-+ .load_mask = CM_PLLD_LOADDSI0,
-+ .hold_mask = CM_PLLD_HOLDDSI0,
-+ .fixed_divider = 1),
-+ [BCM2835_PLLD_DSI1] = REGISTER_PLL_DIV(
-+ .name = "plld_dsi1",
-+ .source_pll = "plld",
-+ .cm_reg = CM_PLLD,
-+ .a2w_reg = A2W_PLLD_DSI1,
-+ .load_mask = CM_PLLD_LOADDSI1,
-+ .hold_mask = CM_PLLD_HOLDDSI1,
-+ .fixed_divider = 1),
-
- /*
- * PLLH is used to supply the pixel clock or the AUX clock for the
---- a/include/dt-bindings/clock/bcm2835.h
-+++ b/include/dt-bindings/clock/bcm2835.h
-@@ -45,3 +45,8 @@
- #define BCM2835_CLOCK_PERI_IMAGE 29
- #define BCM2835_CLOCK_PWM 30
- #define BCM2835_CLOCK_PCM 31
-+
-+#define BCM2835_PLLA_DSI0 32
-+#define BCM2835_PLLA_CCP2 33
-+#define BCM2835_PLLD_DSI0 34
-+#define BCM2835_PLLD_DSI1 35
diff --git a/target/linux/brcm2708/patches-4.4/0263-clk-bcm2835-add-missing-osc-and-per-clocks.patch b/target/linux/brcm2708/patches-4.4/0263-clk-bcm2835-add-missing-osc-and-per-clocks.patch
deleted file mode 100644
index 23e5182..0000000
--- a/target/linux/brcm2708/patches-4.4/0263-clk-bcm2835-add-missing-osc-and-per-clocks.patch
+++ /dev/null
@@ -1,184 +0,0 @@
-From 65bccc432d1f2877a92b7341cbb08b8ef9e0d09d Mon Sep 17 00:00:00 2001
-From: Martin Sperl <kernel at martin.sperl.org>
-Date: Mon, 29 Feb 2016 15:43:57 +0000
-Subject: [PATCH] clk: bcm2835: add missing osc and per clocks
-
-Add AVE0, DFT, GP0, GP1, GP2, SLIM, SMI, TEC, DPI, CAM0, CAM1, DSI0E,
-and DSI1E. PULSE is not added because it has an extra divider.
-
-Signed-off-by: Martin Sperl <kernel at martin.sperl.org>
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit d3d6f15fd376e3dbba851724057b112558c70b79)
----
- drivers/clk/bcm/clk-bcm2835.c | 90 +++++++++++++++++++++++++++++++++++++
- include/dt-bindings/clock/bcm2835.h | 14 ++++++
- 2 files changed, 104 insertions(+)
-
---- a/drivers/clk/bcm/clk-bcm2835.c
-+++ b/drivers/clk/bcm/clk-bcm2835.c
-@@ -117,6 +117,8 @@
- #define CM_SDCCTL 0x1a8
- #define CM_SDCDIV 0x1ac
- #define CM_ARMCTL 0x1b0
-+#define CM_AVEOCTL 0x1b8
-+#define CM_AVEODIV 0x1bc
- #define CM_EMMCCTL 0x1c0
- #define CM_EMMCDIV 0x1c4
-
-@@ -1612,6 +1614,12 @@ static const struct bcm2835_clk_desc clk
- .div_reg = CM_TSENSDIV,
- .int_bits = 5,
- .frac_bits = 0),
-+ [BCM2835_CLOCK_TEC] = REGISTER_OSC_CLK(
-+ .name = "tec",
-+ .ctl_reg = CM_TECCTL,
-+ .div_reg = CM_TECDIV,
-+ .int_bits = 6,
-+ .frac_bits = 0),
-
- /* clocks with vpu parent mux */
- [BCM2835_CLOCK_H264] = REGISTER_VPU_CLK(
-@@ -1626,6 +1634,7 @@ static const struct bcm2835_clk_desc clk
- .div_reg = CM_ISPDIV,
- .int_bits = 4,
- .frac_bits = 8),
-+
- /*
- * Secondary SDRAM clock. Used for low-voltage modes when the PLL
- * in the SDRAM controller can't be used.
-@@ -1657,6 +1666,36 @@ static const struct bcm2835_clk_desc clk
- .is_vpu_clock = true),
-
- /* clocks with per parent mux */
-+ [BCM2835_CLOCK_AVEO] = REGISTER_PER_CLK(
-+ .name = "aveo",
-+ .ctl_reg = CM_AVEOCTL,
-+ .div_reg = CM_AVEODIV,
-+ .int_bits = 4,
-+ .frac_bits = 0),
-+ [BCM2835_CLOCK_CAM0] = REGISTER_PER_CLK(
-+ .name = "cam0",
-+ .ctl_reg = CM_CAM0CTL,
-+ .div_reg = CM_CAM0DIV,
-+ .int_bits = 4,
-+ .frac_bits = 8),
-+ [BCM2835_CLOCK_CAM1] = REGISTER_PER_CLK(
-+ .name = "cam1",
-+ .ctl_reg = CM_CAM1CTL,
-+ .div_reg = CM_CAM1DIV,
-+ .int_bits = 4,
-+ .frac_bits = 8),
-+ [BCM2835_CLOCK_DFT] = REGISTER_PER_CLK(
-+ .name = "dft",
-+ .ctl_reg = CM_DFTCTL,
-+ .div_reg = CM_DFTDIV,
-+ .int_bits = 5,
-+ .frac_bits = 0),
-+ [BCM2835_CLOCK_DPI] = REGISTER_PER_CLK(
-+ .name = "dpi",
-+ .ctl_reg = CM_DPICTL,
-+ .div_reg = CM_DPIDIV,
-+ .int_bits = 4,
-+ .frac_bits = 8),
-
- /* Arasan EMMC clock */
- [BCM2835_CLOCK_EMMC] = REGISTER_PER_CLK(
-@@ -1665,6 +1704,29 @@ static const struct bcm2835_clk_desc clk
- .div_reg = CM_EMMCDIV,
- .int_bits = 4,
- .frac_bits = 8),
-+
-+ /* General purpose (GPIO) clocks */
-+ [BCM2835_CLOCK_GP0] = REGISTER_PER_CLK(
-+ .name = "gp0",
-+ .ctl_reg = CM_GP0CTL,
-+ .div_reg = CM_GP0DIV,
-+ .int_bits = 12,
-+ .frac_bits = 12,
-+ .is_mash_clock = true),
-+ [BCM2835_CLOCK_GP1] = REGISTER_PER_CLK(
-+ .name = "gp1",
-+ .ctl_reg = CM_GP1CTL,
-+ .div_reg = CM_GP1DIV,
-+ .int_bits = 12,
-+ .frac_bits = 12,
-+ .is_mash_clock = true),
-+ [BCM2835_CLOCK_GP2] = REGISTER_PER_CLK(
-+ .name = "gp2",
-+ .ctl_reg = CM_GP2CTL,
-+ .div_reg = CM_GP2DIV,
-+ .int_bits = 12,
-+ .frac_bits = 12),
-+
- /* HDMI state machine */
- [BCM2835_CLOCK_HSM] = REGISTER_PER_CLK(
- .name = "hsm",
-@@ -1686,12 +1748,26 @@ static const struct bcm2835_clk_desc clk
- .int_bits = 12,
- .frac_bits = 12,
- .is_mash_clock = true),
-+ [BCM2835_CLOCK_SLIM] = REGISTER_PER_CLK(
-+ .name = "slim",
-+ .ctl_reg = CM_SLIMCTL,
-+ .div_reg = CM_SLIMDIV,
-+ .int_bits = 12,
-+ .frac_bits = 12,
-+ .is_mash_clock = true),
-+ [BCM2835_CLOCK_SMI] = REGISTER_PER_CLK(
-+ .name = "smi",
-+ .ctl_reg = CM_SMICTL,
-+ .div_reg = CM_SMIDIV,
-+ .int_bits = 4,
-+ .frac_bits = 8),
- [BCM2835_CLOCK_UART] = REGISTER_PER_CLK(
- .name = "uart",
- .ctl_reg = CM_UARTCTL,
- .div_reg = CM_UARTDIV,
- .int_bits = 10,
- .frac_bits = 12),
-+
- /* TV encoder clock. Only operating frequency is 108Mhz. */
- [BCM2835_CLOCK_VEC] = REGISTER_PER_CLK(
- .name = "vec",
-@@ -1700,6 +1776,20 @@ static const struct bcm2835_clk_desc clk
- .int_bits = 4,
- .frac_bits = 0),
-
-+ /* dsi clocks */
-+ [BCM2835_CLOCK_DSI0E] = REGISTER_PER_CLK(
-+ .name = "dsi0e",
-+ .ctl_reg = CM_DSI0ECTL,
-+ .div_reg = CM_DSI0EDIV,
-+ .int_bits = 4,
-+ .frac_bits = 8),
-+ [BCM2835_CLOCK_DSI1E] = REGISTER_PER_CLK(
-+ .name = "dsi1e",
-+ .ctl_reg = CM_DSI1ECTL,
-+ .div_reg = CM_DSI1EDIV,
-+ .int_bits = 4,
-+ .frac_bits = 8),
-+
- /* the gates */
-
- /*
---- a/include/dt-bindings/clock/bcm2835.h
-+++ b/include/dt-bindings/clock/bcm2835.h
-@@ -50,3 +50,17 @@
- #define BCM2835_PLLA_CCP2 33
- #define BCM2835_PLLD_DSI0 34
- #define BCM2835_PLLD_DSI1 35
-+
-+#define BCM2835_CLOCK_AVEO 36
-+#define BCM2835_CLOCK_DFT 37
-+#define BCM2835_CLOCK_GP0 38
-+#define BCM2835_CLOCK_GP1 39
-+#define BCM2835_CLOCK_GP2 40
-+#define BCM2835_CLOCK_SLIM 41
-+#define BCM2835_CLOCK_SMI 42
-+#define BCM2835_CLOCK_TEC 43
-+#define BCM2835_CLOCK_DPI 44
-+#define BCM2835_CLOCK_CAM0 45
-+#define BCM2835_CLOCK_CAM1 46
-+#define BCM2835_CLOCK_DSI0E 47
-+#define BCM2835_CLOCK_DSI1E 48
diff --git a/target/linux/brcm2708/patches-4.4/0264-ARM-bcm2835-Define-two-new-packets-from-the-latest-f.patch b/target/linux/brcm2708/patches-4.4/0264-ARM-bcm2835-Define-two-new-packets-from-the-latest-f.patch
deleted file mode 100644
index 924ee74..0000000
--- a/target/linux/brcm2708/patches-4.4/0264-ARM-bcm2835-Define-two-new-packets-from-the-latest-f.patch
+++ /dev/null
@@ -1,33 +0,0 @@
-From 9647b869fb509fc92d0e9d90dd29895f00a0d467 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 1 Dec 2015 16:49:12 -0800
-Subject: [PATCH] ARM: bcm2835: Define two new packets from the latest
- firmware.
-
-These packets give us direct access to the firmware's power management
-code, as opposed to GET/SET_POWER_STATE packets that only had a couple
-of domains implemented.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Reviewed-by: Kevin Hilman <khilman at linaro.org>
-(cherry picked from commit 60d56333e869be6ad6926cdba3ba974512b2183b)
----
- include/soc/bcm2835/raspberrypi-firmware.h | 2 ++
- 1 file changed, 2 insertions(+)
-
---- a/include/soc/bcm2835/raspberrypi-firmware.h
-+++ b/include/soc/bcm2835/raspberrypi-firmware.h
-@@ -74,11 +74,13 @@ enum rpi_firmware_property_tag {
- RPI_FIRMWARE_GET_DISPMANX_RESOURCE_MEM_HANDLE = 0x00030014,
- RPI_FIRMWARE_GET_EDID_BLOCK = 0x00030020,
- RPI_FIRMWARE_GET_CUSTOMER_OTP = 0x00030021,
-+ RPI_FIRMWARE_GET_DOMAIN_STATE = 0x00030030,
- RPI_FIRMWARE_SET_CLOCK_STATE = 0x00038001,
- RPI_FIRMWARE_SET_CLOCK_RATE = 0x00038002,
- RPI_FIRMWARE_SET_VOLTAGE = 0x00038003,
- RPI_FIRMWARE_SET_TURBO = 0x00038009,
- RPI_FIRMWARE_SET_CUSTOMER_OTP = 0x00038021,
-+ RPI_FIRMWARE_SET_DOMAIN_STATE = 0x00038030,
- RPI_FIRMWARE_SET_SDHOST_CLOCK = 0x00038042,
-
- /* Dispmanx TAGS */
diff --git a/target/linux/brcm2708/patches-4.4/0265-ARM-bcm2835-add-rpi-power-domain-driver.patch b/target/linux/brcm2708/patches-4.4/0265-ARM-bcm2835-add-rpi-power-domain-driver.patch
deleted file mode 100644
index 6b0c249..0000000
--- a/target/linux/brcm2708/patches-4.4/0265-ARM-bcm2835-add-rpi-power-domain-driver.patch
+++ /dev/null
@@ -1,361 +0,0 @@
-From a537e763c6c8d5516b6a66d053b10ce782db53df Mon Sep 17 00:00:00 2001
-From: Alexander Aring <alex.aring at gmail.com>
-Date: Wed, 16 Dec 2015 16:26:47 -0800
-Subject: [PATCH] ARM: bcm2835: add rpi power domain driver
-
-This patch adds support for several power domains on Raspberry Pi,
-including USB (so it can be enabled even if the bootloader didn't do
-it), and graphics.
-
-This patch is the combined work of Eric Anholt (who wrote USB support
-inside of the Raspberry Pi firmware driver, and wrote the non-USB
-domain support) and Alexander Aring (who separated the original USB
-work out from the firmware driver).
-
-Signed-off-by: Alexander Aring <alex.aring at gmail.com>
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Reviewed-by: Ulf Hansson <ulf.hansson at linaro.org>
-Reviewed-by: Kevin Hilman <khilman at linaro.org>
-(cherry picked from commit a09cd356586d33f64cbe64ee4f5c1a7c4a6abee5)
----
- drivers/soc/Kconfig | 1 +
- drivers/soc/Makefile | 1 +
- drivers/soc/bcm/Kconfig | 9 +
- drivers/soc/bcm/Makefile | 1 +
- drivers/soc/bcm/raspberrypi-power.c | 247 ++++++++++++++++++++++++++
- include/dt-bindings/power/raspberrypi-power.h | 41 +++++
- 6 files changed, 300 insertions(+)
- create mode 100644 drivers/soc/bcm/Kconfig
- create mode 100644 drivers/soc/bcm/Makefile
- create mode 100644 drivers/soc/bcm/raspberrypi-power.c
- create mode 100644 include/dt-bindings/power/raspberrypi-power.h
-
---- a/drivers/soc/Kconfig
-+++ b/drivers/soc/Kconfig
-@@ -1,5 +1,6 @@
- menu "SOC (System On Chip) specific Drivers"
-
-+source "drivers/soc/bcm/Kconfig"
- source "drivers/soc/brcmstb/Kconfig"
- source "drivers/soc/mediatek/Kconfig"
- source "drivers/soc/qcom/Kconfig"
---- a/drivers/soc/Makefile
-+++ b/drivers/soc/Makefile
-@@ -2,6 +2,7 @@
- # Makefile for the Linux Kernel SOC specific device drivers.
- #
-
-+obj-y += bcm/
- obj-$(CONFIG_SOC_BRCMSTB) += brcmstb/
- obj-$(CONFIG_MACH_DOVE) += dove/
- obj-$(CONFIG_ARCH_MEDIATEK) += mediatek/
---- /dev/null
-+++ b/drivers/soc/bcm/Kconfig
-@@ -0,0 +1,9 @@
-+config RASPBERRYPI_POWER
-+ bool "Raspberry Pi power domain driver"
-+ depends on ARCH_BCM2835 || COMPILE_TEST
-+ depends on RASPBERRYPI_FIRMWARE
-+ select PM_GENERIC_DOMAINS if PM
-+ select PM_GENERIC_DOMAINS_OF if PM
-+ help
-+ This enables support for the RPi power domains which can be enabled
-+ or disabled via the RPi firmware.
---- /dev/null
-+++ b/drivers/soc/bcm/Makefile
-@@ -0,0 +1 @@
-+obj-$(CONFIG_RASPBERRYPI_POWER) += raspberrypi-power.o
---- /dev/null
-+++ b/drivers/soc/bcm/raspberrypi-power.c
-@@ -0,0 +1,247 @@
-+/* (C) 2015 Pengutronix, Alexander Aring <aar at pengutronix.de>
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ *
-+ * Authors:
-+ * Alexander Aring <aar at pengutronix.de>
-+ * Eric Anholt <eric at anholt.net>
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/of_platform.h>
-+#include <linux/platform_device.h>
-+#include <linux/pm_domain.h>
-+#include <dt-bindings/power/raspberrypi-power.h>
-+#include <soc/bcm2835/raspberrypi-firmware.h>
-+
-+/*
-+ * Firmware indices for the old power domains interface. Only a few
-+ * of them were actually implemented.
-+ */
-+#define RPI_OLD_POWER_DOMAIN_USB 3
-+#define RPI_OLD_POWER_DOMAIN_V3D 10
-+
-+struct rpi_power_domain {
-+ u32 domain;
-+ bool enabled;
-+ bool old_interface;
-+ struct generic_pm_domain base;
-+ struct rpi_firmware *fw;
-+};
-+
-+struct rpi_power_domains {
-+ bool has_new_interface;
-+ struct genpd_onecell_data xlate;
-+ struct rpi_firmware *fw;
-+ struct rpi_power_domain domains[RPI_POWER_DOMAIN_COUNT];
-+};
-+
-+/*
-+ * Packet definition used by RPI_FIRMWARE_SET_POWER_STATE and
-+ * RPI_FIRMWARE_SET_DOMAIN_STATE
-+ */
-+struct rpi_power_domain_packet {
-+ u32 domain;
-+ u32 on;
-+} __packet;
-+
-+/*
-+ * Asks the firmware to enable or disable power on a specific power
-+ * domain.
-+ */
-+static int rpi_firmware_set_power(struct rpi_power_domain *rpi_domain, bool on)
-+{
-+ struct rpi_power_domain_packet packet;
-+
-+ packet.domain = rpi_domain->domain;
-+ packet.on = on;
-+ return rpi_firmware_property(rpi_domain->fw,
-+ rpi_domain->old_interface ?
-+ RPI_FIRMWARE_SET_POWER_STATE :
-+ RPI_FIRMWARE_SET_DOMAIN_STATE,
-+ &packet, sizeof(packet));
-+}
-+
-+static int rpi_domain_off(struct generic_pm_domain *domain)
-+{
-+ struct rpi_power_domain *rpi_domain =
-+ container_of(domain, struct rpi_power_domain, base);
-+
-+ return rpi_firmware_set_power(rpi_domain, false);
-+}
-+
-+static int rpi_domain_on(struct generic_pm_domain *domain)
-+{
-+ struct rpi_power_domain *rpi_domain =
-+ container_of(domain, struct rpi_power_domain, base);
-+
-+ return rpi_firmware_set_power(rpi_domain, true);
-+}
-+
-+static void rpi_common_init_power_domain(struct rpi_power_domains *rpi_domains,
-+ int xlate_index, const char *name)
-+{
-+ struct rpi_power_domain *dom = &rpi_domains->domains[xlate_index];
-+
-+ dom->fw = rpi_domains->fw;
-+
-+ dom->base.name = name;
-+ dom->base.power_on = rpi_domain_on;
-+ dom->base.power_off = rpi_domain_off;
-+
-+ /*
-+ * Treat all power domains as off at boot.
-+ *
-+ * The firmware itself may be keeping some domains on, but
-+ * from Linux's perspective all we control is the refcounts
-+ * that we give to the firmware, and we can't ask the firmware
-+ * to turn off something that we haven't ourselves turned on.
-+ */
-+ pm_genpd_init(&dom->base, NULL, true);
-+
-+ rpi_domains->xlate.domains[xlate_index] = &dom->base;
-+}
-+
-+static void rpi_init_power_domain(struct rpi_power_domains *rpi_domains,
-+ int xlate_index, const char *name)
-+{
-+ struct rpi_power_domain *dom = &rpi_domains->domains[xlate_index];
-+
-+ if (!rpi_domains->has_new_interface)
-+ return;
-+
-+ /* The DT binding index is the firmware's domain index minus one. */
-+ dom->domain = xlate_index + 1;
-+
-+ rpi_common_init_power_domain(rpi_domains, xlate_index, name);
-+}
-+
-+static void rpi_init_old_power_domain(struct rpi_power_domains *rpi_domains,
-+ int xlate_index, int domain,
-+ const char *name)
-+{
-+ struct rpi_power_domain *dom = &rpi_domains->domains[xlate_index];
-+
-+ dom->old_interface = true;
-+ dom->domain = domain;
-+
-+ rpi_common_init_power_domain(rpi_domains, xlate_index, name);
-+}
-+
-+/*
-+ * Detects whether the firmware supports the new power domains interface.
-+ *
-+ * The firmware doesn't actually return an error on an unknown tag,
-+ * and just skips over it, so we do the detection by putting an
-+ * unexpected value in the return field and checking if it was
-+ * unchanged.
-+ */
-+static bool
-+rpi_has_new_domain_support(struct rpi_power_domains *rpi_domains)
-+{
-+ struct rpi_power_domain_packet packet;
-+ int ret;
-+
-+ packet.domain = RPI_POWER_DOMAIN_ARM;
-+ packet.on = ~0;
-+
-+ ret = rpi_firmware_property(rpi_domains->fw,
-+ RPI_FIRMWARE_GET_DOMAIN_STATE,
-+ &packet, sizeof(packet));
-+
-+ return ret == 0 && packet.on != ~0;
-+}
-+
-+static int rpi_power_probe(struct platform_device *pdev)
-+{
-+ struct device_node *fw_np;
-+ struct device *dev = &pdev->dev;
-+ struct rpi_power_domains *rpi_domains;
-+
-+ rpi_domains = devm_kzalloc(dev, sizeof(*rpi_domains), GFP_KERNEL);
-+ if (!rpi_domains)
-+ return -ENOMEM;
-+
-+ rpi_domains->xlate.domains =
-+ devm_kzalloc(dev, sizeof(*rpi_domains->xlate.domains) *
-+ RPI_POWER_DOMAIN_COUNT, GFP_KERNEL);
-+ if (!rpi_domains->xlate.domains)
-+ return -ENOMEM;
-+
-+ rpi_domains->xlate.num_domains = RPI_POWER_DOMAIN_COUNT;
-+
-+ fw_np = of_parse_phandle(pdev->dev.of_node, "firmware", 0);
-+ if (!fw_np) {
-+ dev_err(&pdev->dev, "no firmware node\n");
-+ return -ENODEV;
-+ }
-+
-+ rpi_domains->fw = rpi_firmware_get(fw_np);
-+ of_node_put(fw_np);
-+ if (!rpi_domains->fw)
-+ return -EPROBE_DEFER;
-+
-+ rpi_domains->has_new_interface =
-+ rpi_has_new_domain_support(rpi_domains);
-+
-+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_I2C0, "I2C0");
-+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_I2C1, "I2C1");
-+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_I2C2, "I2C2");
-+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_VIDEO_SCALER,
-+ "VIDEO_SCALER");
-+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_VPU1, "VPU1");
-+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_HDMI, "HDMI");
-+
-+ /*
-+ * Use the old firmware interface for USB power, so that we
-+ * can turn it on even if the firmware hasn't been updated.
-+ */
-+ rpi_init_old_power_domain(rpi_domains, RPI_POWER_DOMAIN_USB,
-+ RPI_OLD_POWER_DOMAIN_USB, "USB");
-+
-+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_VEC, "VEC");
-+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_JPEG, "JPEG");
-+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_H264, "H264");
-+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_V3D, "V3D");
-+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_ISP, "ISP");
-+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_UNICAM0, "UNICAM0");
-+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_UNICAM1, "UNICAM1");
-+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_CCP2RX, "CCP2RX");
-+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_CSI2, "CSI2");
-+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_CPI, "CPI");
-+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_DSI0, "DSI0");
-+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_DSI1, "DSI1");
-+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_TRANSPOSER,
-+ "TRANSPOSER");
-+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_CCP2TX, "CCP2TX");
-+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_CDP, "CDP");
-+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_ARM, "ARM");
-+
-+ of_genpd_add_provider_onecell(dev->of_node, &rpi_domains->xlate);
-+
-+ platform_set_drvdata(pdev, rpi_domains);
-+
-+ return 0;
-+}
-+
-+static const struct of_device_id rpi_power_of_match[] = {
-+ { .compatible = "raspberrypi,bcm2835-power", },
-+ {},
-+};
-+MODULE_DEVICE_TABLE(of, rpi_power_of_match);
-+
-+static struct platform_driver rpi_power_driver = {
-+ .driver = {
-+ .name = "raspberrypi-power",
-+ .of_match_table = rpi_power_of_match,
-+ },
-+ .probe = rpi_power_probe,
-+};
-+builtin_platform_driver(rpi_power_driver);
-+
-+MODULE_AUTHOR("Alexander Aring <aar at pengutronix.de>");
-+MODULE_AUTHOR("Eric Anholt <eric at anholt.net>");
-+MODULE_DESCRIPTION("Raspberry Pi power domain driver");
-+MODULE_LICENSE("GPL v2");
---- /dev/null
-+++ b/include/dt-bindings/power/raspberrypi-power.h
-@@ -0,0 +1,41 @@
-+/*
-+ * Copyright © 2015 Broadcom
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ */
-+
-+#ifndef _DT_BINDINGS_ARM_BCM2835_RPI_POWER_H
-+#define _DT_BINDINGS_ARM_BCM2835_RPI_POWER_H
-+
-+/* These power domain indices are the firmware interface's indices
-+ * minus one.
-+ */
-+#define RPI_POWER_DOMAIN_I2C0 0
-+#define RPI_POWER_DOMAIN_I2C1 1
-+#define RPI_POWER_DOMAIN_I2C2 2
-+#define RPI_POWER_DOMAIN_VIDEO_SCALER 3
-+#define RPI_POWER_DOMAIN_VPU1 4
-+#define RPI_POWER_DOMAIN_HDMI 5
-+#define RPI_POWER_DOMAIN_USB 6
-+#define RPI_POWER_DOMAIN_VEC 7
-+#define RPI_POWER_DOMAIN_JPEG 8
-+#define RPI_POWER_DOMAIN_H264 9
-+#define RPI_POWER_DOMAIN_V3D 10
-+#define RPI_POWER_DOMAIN_ISP 11
-+#define RPI_POWER_DOMAIN_UNICAM0 12
-+#define RPI_POWER_DOMAIN_UNICAM1 13
-+#define RPI_POWER_DOMAIN_CCP2RX 14
-+#define RPI_POWER_DOMAIN_CSI2 15
-+#define RPI_POWER_DOMAIN_CPI 16
-+#define RPI_POWER_DOMAIN_DSI0 17
-+#define RPI_POWER_DOMAIN_DSI1 18
-+#define RPI_POWER_DOMAIN_TRANSPOSER 19
-+#define RPI_POWER_DOMAIN_CCP2TX 20
-+#define RPI_POWER_DOMAIN_CDP 21
-+#define RPI_POWER_DOMAIN_ARM 22
-+
-+#define RPI_POWER_DOMAIN_COUNT 23
-+
-+#endif /* _DT_BINDINGS_ARM_BCM2835_RPI_POWER_H */
diff --git a/target/linux/brcm2708/patches-4.4/0266-ARM-bcm2835-clarify-RASPBERRYPI_FIRMWARE-dependency.patch b/target/linux/brcm2708/patches-4.4/0266-ARM-bcm2835-clarify-RASPBERRYPI_FIRMWARE-dependency.patch
deleted file mode 100644
index 8004d68..0000000
--- a/target/linux/brcm2708/patches-4.4/0266-ARM-bcm2835-clarify-RASPBERRYPI_FIRMWARE-dependency.patch
+++ /dev/null
@@ -1,36 +0,0 @@
-From d9ae89f6995870072c3237f6be8ecbd0213685ab Mon Sep 17 00:00:00 2001
-From: Arnd Bergmann <arnd at arndb.de>
-Date: Thu, 31 Dec 2015 23:39:14 +0100
-Subject: [PATCH] ARM: bcm2835: clarify RASPBERRYPI_FIRMWARE dependency
-
-The firmware driver can be a loadable module, but the power domain
-can only be built-in, so we get a build error in an allmodconfig
-kernel:
-
-:(.text+0x17e59c): undefined reference to `rpi_firmware_property'
-:(.text+0x17e51c): undefined reference to `rpi_firmware_get'
-:(.text+0x17e244): undefined reference to `rpi_firmware_property'
-
-This changes the dependency to only allow the power domain code
-to be enabled when the firmware driver is built-in. Other users
-of the firmware driver may still be loadable modules and not
-everyone needs the power domains, so we don't change the firmware
-code.
-
-Signed-off-by: Arnd Bergmann <arnd at arndb.de>
-(cherry picked from commit 22a5b1ddd83b991b96cb635898e011cce48bf6f8)
----
- drivers/soc/bcm/Kconfig | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/soc/bcm/Kconfig
-+++ b/drivers/soc/bcm/Kconfig
-@@ -1,7 +1,7 @@
- config RASPBERRYPI_POWER
- bool "Raspberry Pi power domain driver"
- depends on ARCH_BCM2835 || COMPILE_TEST
-- depends on RASPBERRYPI_FIRMWARE
-+ depends on RASPBERRYPI_FIRMWARE=y
- select PM_GENERIC_DOMAINS if PM
- select PM_GENERIC_DOMAINS_OF if PM
- help
diff --git a/target/linux/brcm2708/patches-4.4/0267-ARM-bcm2708-Enable-building-power-domain-driver.patch b/target/linux/brcm2708/patches-4.4/0267-ARM-bcm2708-Enable-building-power-domain-driver.patch
deleted file mode 100644
index 876c0ce..0000000
--- a/target/linux/brcm2708/patches-4.4/0267-ARM-bcm2708-Enable-building-power-domain-driver.patch
+++ /dev/null
@@ -1,20 +0,0 @@
-From 1110ec3ffb9ed8f6f5eb11e8da530fc873f23e80 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 19 Apr 2016 15:55:02 -0700
-Subject: [PATCH] ARM: bcm2708: Enable building power domain driver.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/soc/bcm/Kconfig | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/soc/bcm/Kconfig
-+++ b/drivers/soc/bcm/Kconfig
-@@ -1,6 +1,6 @@
- config RASPBERRYPI_POWER
- bool "Raspberry Pi power domain driver"
-- depends on ARCH_BCM2835 || COMPILE_TEST
-+ depends on ARCH_BCM2835 || ARCH_BCM2708 || ARCH_BCM2709 || COMPILE_TEST
- depends on RASPBERRYPI_FIRMWARE=y
- select PM_GENERIC_DOMAINS if PM
- select PM_GENERIC_DOMAINS_OF if PM
diff --git a/target/linux/brcm2708/patches-4.4/0268-bcm2708-Add-RASPBERRYPI_POWER-to-the-defconfigs.patch b/target/linux/brcm2708/patches-4.4/0268-bcm2708-Add-RASPBERRYPI_POWER-to-the-defconfigs.patch
deleted file mode 100644
index 0429226..0000000
--- a/target/linux/brcm2708/patches-4.4/0268-bcm2708-Add-RASPBERRYPI_POWER-to-the-defconfigs.patch
+++ /dev/null
@@ -1,50 +0,0 @@
-From fd3735ba9a90c34384b5d9da5b66d71257762ed0 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 19 Apr 2016 14:23:30 -0700
-Subject: [PATCH] bcm2708: Add RASPBERRYPI_POWER to the defconfigs.
-
-This will be used by the GPU driver for powering on HDMI at boot time
-and for 3D hang reset.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- arch/arm/configs/bcm2709_defconfig | 2 ++
- arch/arm/configs/bcmrpi_defconfig | 2 ++
- 2 files changed, 4 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -71,6 +71,7 @@ CONFIG_NEON=y
- CONFIG_KERNEL_MODE_NEON=y
- CONFIG_BINFMT_MISC=m
- # CONFIG_SUSPEND is not set
-+CONFIG_PM=y
- CONFIG_NET=y
- CONFIG_PACKET=y
- CONFIG_UNIX=y
-@@ -1116,6 +1117,7 @@ CONFIG_FB_TFT_FBTFT_DEVICE=m
- CONFIG_MAILBOX=y
- CONFIG_BCM2835_MBOX=y
- # CONFIG_IOMMU_SUPPORT is not set
-+CONFIG_RASPBERRYPI_POWER=y
- CONFIG_EXTCON=m
- CONFIG_EXTCON_ARIZONA=m
- CONFIG_IIO=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -64,6 +64,7 @@ CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
- CONFIG_VFP=y
- CONFIG_BINFMT_MISC=m
- # CONFIG_SUSPEND is not set
-+CONFIG_PM=y
- CONFIG_NET=y
- CONFIG_PACKET=y
- CONFIG_UNIX=y
-@@ -1123,6 +1124,7 @@ CONFIG_FB_TFT_FBTFT_DEVICE=m
- CONFIG_MAILBOX=y
- CONFIG_BCM2835_MBOX=y
- # CONFIG_IOMMU_SUPPORT is not set
-+CONFIG_RASPBERRYPI_POWER=y
- CONFIG_EXTCON=m
- CONFIG_EXTCON_ARIZONA=m
- CONFIG_IIO=m
diff --git a/target/linux/brcm2708/patches-4.4/0269-bcm2708-Add-the-power-domain-driver-to-the-device-tr.patch b/target/linux/brcm2708/patches-4.4/0269-bcm2708-Add-the-power-domain-driver-to-the-device-tr.patch
deleted file mode 100644
index d5849ee..0000000
--- a/target/linux/brcm2708/patches-4.4/0269-bcm2708-Add-the-power-domain-driver-to-the-device-tr.patch
+++ /dev/null
@@ -1,25 +0,0 @@
-From f4ebbf7c02b68dbbce6fc3346e291984e3bf17ae Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 19 Apr 2016 14:36:31 -0700
-Subject: [PATCH] bcm2708: Add the power domain driver to the device tree.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- arch/arm/boot/dts/bcm2708_common.dtsi | 6 ++++++
- 1 file changed, 6 insertions(+)
-
---- a/arch/arm/boot/dts/bcm2708_common.dtsi
-+++ b/arch/arm/boot/dts/bcm2708_common.dtsi
-@@ -285,6 +285,12 @@
- mboxes = <&mailbox>;
- };
-
-+ power: power {
-+ compatible = "raspberrypi,bcm2835-power";
-+ firmware = <&firmware>;
-+ #power-domain-cells = <1>;
-+ };
-+
- leds: leds {
- compatible = "gpio-leds";
- };
diff --git a/target/linux/brcm2708/patches-4.4/0270-bcm2708-Reference-the-HDMI-power-domain-for-the-HDMI.patch b/target/linux/brcm2708/patches-4.4/0270-bcm2708-Reference-the-HDMI-power-domain-for-the-HDMI.patch
deleted file mode 100644
index b584820..0000000
--- a/target/linux/brcm2708/patches-4.4/0270-bcm2708-Reference-the-HDMI-power-domain-for-the-HDMI.patch
+++ /dev/null
@@ -1,28 +0,0 @@
-From 3f85b3a12fa31a983da125aa7042f9527b7c1193 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 19 Apr 2016 14:40:08 -0700
-Subject: [PATCH] bcm2708: Reference the HDMI power domain for the HDMI driver.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts | 2 ++
- 1 file changed, 2 insertions(+)
-
---- a/arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts
-@@ -6,6 +6,7 @@
- /plugin/;
-
- #include "dt-bindings/clock/bcm2835.h"
-+#include "dt-bindings/power/raspberrypi-power.h"
- #include "dt-bindings/gpio/gpio.h"
-
- / {
-@@ -72,6 +73,7 @@
- clocks = <&cprman BCM2835_PLLH_PIX>,
- <&cprman BCM2835_CLOCK_HSM>;
- clock-names = "pixel", "hdmi";
-+ power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
- };
-
- v3d at 7ec00000 {
diff --git a/target/linux/brcm2708/patches-4.4/0271-drm-vc4-copy_to_user-returns-the-number-of-bytes-rem.patch b/target/linux/brcm2708/patches-4.4/0271-drm-vc4-copy_to_user-returns-the-number-of-bytes-rem.patch
deleted file mode 100644
index 0f885f6..0000000
--- a/target/linux/brcm2708/patches-4.4/0271-drm-vc4-copy_to_user-returns-the-number-of-bytes-rem.patch
+++ /dev/null
@@ -1,86 +0,0 @@
-From 2f8406d49325d00a4f71a3045901662b29c96278 Mon Sep 17 00:00:00 2001
-From: Dan Carpenter <dan.carpenter at oracle.com>
-Date: Thu, 17 Dec 2015 15:36:28 +0300
-Subject: [PATCH] drm/vc4: copy_to_user() returns the number of bytes remaining
-
-The copy_to/from_user() functions return the number of bytes remaining
-to be copied. We want to return error codes here.
-
-Also it's a bad idea to print an error message if a copy from user fails
-because users can use that to spam /var/log/messages which is annoying
-so I removed those.
-
-Fixes: 214613656b51 ('drm/vc4: Add an interface for capturing the GPU state after a hang.')
-Signed-off-by: Dan Carpenter <dan.carpenter at oracle.com>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 65c4777de54a39b2722a4b1ff3306d044014d511)
----
- drivers/gpu/drm/vc4/vc4_gem.c | 37 ++++++++++++++++++-------------------
- 1 file changed, 18 insertions(+), 19 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -85,7 +85,7 @@ vc4_get_hang_state_ioctl(struct drm_devi
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- unsigned long irqflags;
- u32 i;
-- int ret;
-+ int ret = 0;
-
- spin_lock_irqsave(&vc4->job_lock, irqflags);
- kernel_state = vc4->hang_state;
-@@ -133,9 +133,11 @@ vc4_get_hang_state_ioctl(struct drm_devi
- bo_state[i].size = vc4_bo->base.base.size;
- }
-
-- ret = copy_to_user((void __user *)(uintptr_t)get_state->bo,
-- bo_state,
-- state->bo_count * sizeof(*bo_state));
-+ if (copy_to_user((void __user *)(uintptr_t)get_state->bo,
-+ bo_state,
-+ state->bo_count * sizeof(*bo_state)))
-+ ret = -EFAULT;
-+
- kfree(bo_state);
-
- err_free:
-@@ -563,27 +565,24 @@ vc4_get_bcl(struct drm_device *dev, stru
- exec->shader_state = temp + exec_size;
- exec->shader_state_size = args->shader_rec_count;
-
-- ret = copy_from_user(bin,
-- (void __user *)(uintptr_t)args->bin_cl,
-- args->bin_cl_size);
-- if (ret) {
-- DRM_ERROR("Failed to copy in bin cl\n");
-+ if (copy_from_user(bin,
-+ (void __user *)(uintptr_t)args->bin_cl,
-+ args->bin_cl_size)) {
-+ ret = -EFAULT;
- goto fail;
- }
-
-- ret = copy_from_user(exec->shader_rec_u,
-- (void __user *)(uintptr_t)args->shader_rec,
-- args->shader_rec_size);
-- if (ret) {
-- DRM_ERROR("Failed to copy in shader recs\n");
-+ if (copy_from_user(exec->shader_rec_u,
-+ (void __user *)(uintptr_t)args->shader_rec,
-+ args->shader_rec_size)) {
-+ ret = -EFAULT;
- goto fail;
- }
-
-- ret = copy_from_user(exec->uniforms_u,
-- (void __user *)(uintptr_t)args->uniforms,
-- args->uniforms_size);
-- if (ret) {
-- DRM_ERROR("Failed to copy in uniforms cl\n");
-+ if (copy_from_user(exec->uniforms_u,
-+ (void __user *)(uintptr_t)args->uniforms,
-+ args->uniforms_size)) {
-+ ret = -EFAULT;
- goto fail;
- }
-
diff --git a/target/linux/brcm2708/patches-4.4/0272-drm-vc4-allocate-enough-memory-in-vc4_save_hang_stat.patch b/target/linux/brcm2708/patches-4.4/0272-drm-vc4-allocate-enough-memory-in-vc4_save_hang_stat.patch
deleted file mode 100644
index f266ba6..0000000
--- a/target/linux/brcm2708/patches-4.4/0272-drm-vc4-allocate-enough-memory-in-vc4_save_hang_stat.patch
+++ /dev/null
@@ -1,26 +0,0 @@
-From 8774a819d4dcf5fc2ce0370cdf40a29d47cde553 Mon Sep 17 00:00:00 2001
-From: Dan Carpenter <dan.carpenter at oracle.com>
-Date: Thu, 17 Dec 2015 15:39:08 +0300
-Subject: [PATCH] drm/vc4: allocate enough memory in vc4_save_hang_state()
-
-"state" is smaller than "kernel_state" so we end up corrupting memory.
-
-Fixes: 214613656b51 ('drm/vc4: Add an interface for capturing the GPU state after a hang.')
-Signed-off-by: Dan Carpenter <dan.carpenter at oracle.com>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 7e5082fbc00cc157e57a70cdb6b9bbb21289afb1)
----
- drivers/gpu/drm/vc4/vc4_gem.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -159,7 +159,7 @@ vc4_save_hang_state(struct drm_device *d
- unsigned long irqflags;
- unsigned int i, unref_list_count;
-
-- kernel_state = kcalloc(1, sizeof(*state), GFP_KERNEL);
-+ kernel_state = kcalloc(1, sizeof(*kernel_state), GFP_KERNEL);
- if (!kernel_state)
- return;
-
diff --git a/target/linux/brcm2708/patches-4.4/0273-drm-vc4-fix-warning-in-validate-printf.patch b/target/linux/brcm2708/patches-4.4/0273-drm-vc4-fix-warning-in-validate-printf.patch
deleted file mode 100644
index b01ae09..0000000
--- a/target/linux/brcm2708/patches-4.4/0273-drm-vc4-fix-warning-in-validate-printf.patch
+++ /dev/null
@@ -1,32 +0,0 @@
-From 89994ac686cb5522e36dbd6a4088cc8490008e44 Mon Sep 17 00:00:00 2001
-From: Dave Airlie <airlied at redhat.com>
-Date: Mon, 18 Jan 2016 09:10:42 +1000
-Subject: [PATCH] drm/vc4: fix warning in validate printf.
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-This just fixes a warning on 64-bit builds:
-
- drivers/gpu/drm/vc4/vc4_validate.c: In function ‘validate_gl_shader_rec’:
- drivers/gpu/drm/vc4/vc4_validate.c:864:12: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t {aka long unsigned int}’ [-Wformat=]
-
-Reported-by: Linus Torvalds <torvalds at linux-foundation.org>
-Signed-off-by: Dave Airlie <airlied at redhat.com>
-Signed-off-by: Linus Torvalds <torvalds at linux-foundation.org>
-(cherry picked from commit c671e1e30259da587d7a0162895200601979ee65)
----
- drivers/gpu/drm/vc4/vc4_validate.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/gpu/drm/vc4/vc4_validate.c
-+++ b/drivers/gpu/drm/vc4/vc4_validate.c
-@@ -861,7 +861,7 @@ validate_gl_shader_rec(struct drm_device
-
- if (vbo->base.size < offset ||
- vbo->base.size - offset < attr_size) {
-- DRM_ERROR("BO offset overflow (%d + %d > %d)\n",
-+ DRM_ERROR("BO offset overflow (%d + %d > %zu)\n",
- offset, attr_size, vbo->base.size);
- return -EINVAL;
- }
diff --git a/target/linux/brcm2708/patches-4.4/0274-drm-vc4-Improve-comments-on-vc4_plane_state-members.patch b/target/linux/brcm2708/patches-4.4/0274-drm-vc4-Improve-comments-on-vc4_plane_state-members.patch
deleted file mode 100644
index cb86035..0000000
--- a/target/linux/brcm2708/patches-4.4/0274-drm-vc4-Improve-comments-on-vc4_plane_state-members.patch
+++ /dev/null
@@ -1,36 +0,0 @@
-From 322440d294ae3c41c4bb06cbc8bb00e87041883f Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 28 Dec 2015 14:14:09 -0800
-Subject: [PATCH] drm/vc4: Improve comments on vc4_plane_state members.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit f427fb16cf756548c39256b569cf083f39bcc4e9)
----
- drivers/gpu/drm/vc4/vc4_plane.c | 9 ++++++---
- 1 file changed, 6 insertions(+), 3 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_plane.c
-+++ b/drivers/gpu/drm/vc4/vc4_plane.c
-@@ -26,16 +26,19 @@
-
- struct vc4_plane_state {
- struct drm_plane_state base;
-+ /* System memory copy of the display list for this element, computed
-+ * at atomic_check time.
-+ */
- u32 *dlist;
-- u32 dlist_size; /* Number of dwords in allocated for the display list */
-+ u32 dlist_size; /* Number of dwords allocated for the display list */
- u32 dlist_count; /* Number of used dwords in the display list. */
-
- /* Offset in the dlist to pointer word 0. */
- u32 pw0_offset;
-
- /* Offset where the plane's dlist was last stored in the
-- hardware at vc4_crtc_atomic_flush() time.
-- */
-+ * hardware at vc4_crtc_atomic_flush() time.
-+ */
- u32 *hw_dlist;
- };
-
diff --git a/target/linux/brcm2708/patches-4.4/0275-drm-vc4-Add-missing-__iomem-annotation-to-hw_dlist.patch b/target/linux/brcm2708/patches-4.4/0275-drm-vc4-Add-missing-__iomem-annotation-to-hw_dlist.patch
deleted file mode 100644
index c8a0748..0000000
--- a/target/linux/brcm2708/patches-4.4/0275-drm-vc4-Add-missing-__iomem-annotation-to-hw_dlist.patch
+++ /dev/null
@@ -1,25 +0,0 @@
-From a8cdc6f8056df9683dd48c06c48c0dce13acfdff Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 28 Dec 2015 14:14:57 -0800
-Subject: [PATCH] drm/vc4: Add missing __iomem annotation to hw_dlist.
-
-This is the pointer to the HVS device's memory where we stored the
-contents of *dlist.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 17eac75111ebda33e13d8d8d98aaedfc1a9c2abf)
----
- drivers/gpu/drm/vc4/vc4_plane.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/gpu/drm/vc4/vc4_plane.c
-+++ b/drivers/gpu/drm/vc4/vc4_plane.c
-@@ -39,7 +39,7 @@ struct vc4_plane_state {
- /* Offset where the plane's dlist was last stored in the
- * hardware at vc4_crtc_atomic_flush() time.
- */
-- u32 *hw_dlist;
-+ u32 __iomem *hw_dlist;
- };
-
- static inline struct vc4_plane_state *
diff --git a/target/linux/brcm2708/patches-4.4/0276-drm-vc4-Move-the-plane-clipping-scaling-setup-to-a-s.patch b/target/linux/brcm2708/patches-4.4/0276-drm-vc4-Move-the-plane-clipping-scaling-setup-to-a-s.patch
deleted file mode 100644
index 0a12da5..0000000
--- a/target/linux/brcm2708/patches-4.4/0276-drm-vc4-Move-the-plane-clipping-scaling-setup-to-a-s.patch
+++ /dev/null
@@ -1,143 +0,0 @@
-From 178cf206ba61689f83872ba1ace6964c59718106 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 28 Dec 2015 14:34:44 -0800
-Subject: [PATCH] drm/vc4: Move the plane clipping/scaling setup to a separate
- function.
-
-As we add actual scaling, this is going to get way more complicated.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 5c6799942003df91801b1d2277bba34d71f99603)
----
- drivers/gpu/drm/vc4/vc4_plane.c | 78 +++++++++++++++++++++++++++--------------
- 1 file changed, 52 insertions(+), 26 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_plane.c
-+++ b/drivers/gpu/drm/vc4/vc4_plane.c
-@@ -40,6 +40,14 @@ struct vc4_plane_state {
- * hardware at vc4_crtc_atomic_flush() time.
- */
- u32 __iomem *hw_dlist;
-+
-+ /* Clipped coordinates of the plane on the display. */
-+ int crtc_x, crtc_y, crtc_w, crtc_h;
-+
-+ /* Offset to start scanning out from the start of the plane's
-+ * BO.
-+ */
-+ u32 offset;
- };
-
- static inline struct vc4_plane_state *
-@@ -167,22 +175,17 @@ static void vc4_dlist_write(struct vc4_p
- vc4_state->dlist[vc4_state->dlist_count++] = val;
- }
-
--/* Writes out a full display list for an active plane to the plane's
-- * private dlist state.
-- */
--static int vc4_plane_mode_set(struct drm_plane *plane,
-- struct drm_plane_state *state)
-+static int vc4_plane_setup_clipping_and_scaling(struct drm_plane_state *state)
- {
- struct vc4_plane_state *vc4_state = to_vc4_plane_state(state);
- struct drm_framebuffer *fb = state->fb;
-- struct drm_gem_cma_object *bo = drm_fb_cma_get_gem_obj(fb, 0);
-- u32 ctl0_offset = vc4_state->dlist_count;
-- const struct hvs_format *format = vc4_get_hvs_format(fb->pixel_format);
-- uint32_t offset = fb->offsets[0];
-- int crtc_x = state->crtc_x;
-- int crtc_y = state->crtc_y;
-- int crtc_w = state->crtc_w;
-- int crtc_h = state->crtc_h;
-+
-+ vc4_state->offset = fb->offsets[0];
-+
-+ vc4_state->crtc_x = state->crtc_x;
-+ vc4_state->crtc_y = state->crtc_y;
-+ vc4_state->crtc_w = state->crtc_w;
-+ vc4_state->crtc_h = state->crtc_h;
-
- if (state->crtc_w << 16 != state->src_w ||
- state->crtc_h << 16 != state->src_h) {
-@@ -194,18 +197,41 @@ static int vc4_plane_mode_set(struct drm
- return -EINVAL;
- }
-
-- if (crtc_x < 0) {
-- offset += drm_format_plane_cpp(fb->pixel_format, 0) * -crtc_x;
-- crtc_w += crtc_x;
-- crtc_x = 0;
-+ if (vc4_state->crtc_x < 0) {
-+ vc4_state->offset += (drm_format_plane_cpp(fb->pixel_format,
-+ 0) *
-+ -vc4_state->crtc_x);
-+ vc4_state->crtc_w += vc4_state->crtc_x;
-+ vc4_state->crtc_x = 0;
- }
-
-- if (crtc_y < 0) {
-- offset += fb->pitches[0] * -crtc_y;
-- crtc_h += crtc_y;
-- crtc_y = 0;
-+ if (vc4_state->crtc_y < 0) {
-+ vc4_state->offset += fb->pitches[0] * -vc4_state->crtc_y;
-+ vc4_state->crtc_h += vc4_state->crtc_y;
-+ vc4_state->crtc_y = 0;
- }
-
-+ return 0;
-+}
-+
-+
-+/* Writes out a full display list for an active plane to the plane's
-+ * private dlist state.
-+ */
-+static int vc4_plane_mode_set(struct drm_plane *plane,
-+ struct drm_plane_state *state)
-+{
-+ struct vc4_plane_state *vc4_state = to_vc4_plane_state(state);
-+ struct drm_framebuffer *fb = state->fb;
-+ struct drm_gem_cma_object *bo = drm_fb_cma_get_gem_obj(fb, 0);
-+ u32 ctl0_offset = vc4_state->dlist_count;
-+ const struct hvs_format *format = vc4_get_hvs_format(fb->pixel_format);
-+ int ret;
-+
-+ ret = vc4_plane_setup_clipping_and_scaling(state);
-+ if (ret)
-+ return ret;
-+
- vc4_dlist_write(vc4_state,
- SCALER_CTL0_VALID |
- (format->pixel_order << SCALER_CTL0_ORDER_SHIFT) |
-@@ -215,8 +241,8 @@ static int vc4_plane_mode_set(struct drm
- /* Position Word 0: Image Positions and Alpha Value */
- vc4_dlist_write(vc4_state,
- VC4_SET_FIELD(0xff, SCALER_POS0_FIXED_ALPHA) |
-- VC4_SET_FIELD(crtc_x, SCALER_POS0_START_X) |
-- VC4_SET_FIELD(crtc_y, SCALER_POS0_START_Y));
-+ VC4_SET_FIELD(vc4_state->crtc_x, SCALER_POS0_START_X) |
-+ VC4_SET_FIELD(vc4_state->crtc_y, SCALER_POS0_START_Y));
-
- /* Position Word 1: Scaled Image Dimensions.
- * Skipped due to SCALER_CTL0_UNITY scaling.
-@@ -228,8 +254,8 @@ static int vc4_plane_mode_set(struct drm
- SCALER_POS2_ALPHA_MODE_PIPELINE :
- SCALER_POS2_ALPHA_MODE_FIXED,
- SCALER_POS2_ALPHA_MODE) |
-- VC4_SET_FIELD(crtc_w, SCALER_POS2_WIDTH) |
-- VC4_SET_FIELD(crtc_h, SCALER_POS2_HEIGHT));
-+ VC4_SET_FIELD(vc4_state->crtc_w, SCALER_POS2_WIDTH) |
-+ VC4_SET_FIELD(vc4_state->crtc_h, SCALER_POS2_HEIGHT));
-
- /* Position Word 3: Context. Written by the HVS. */
- vc4_dlist_write(vc4_state, 0xc0c0c0c0);
-@@ -237,7 +263,7 @@ static int vc4_plane_mode_set(struct drm
- vc4_state->pw0_offset = vc4_state->dlist_count;
-
- /* Pointer Word 0: RGB / Y Pointer */
-- vc4_dlist_write(vc4_state, bo->paddr + offset);
-+ vc4_dlist_write(vc4_state, bo->paddr + vc4_state->offset);
-
- /* Pointer Context Word 0: Written by the HVS */
- vc4_dlist_write(vc4_state, 0xc0c0c0c0);
diff --git a/target/linux/brcm2708/patches-4.4/0277-drm-vc4-Add-a-proper-short-circut-path-for-legacy-cu.patch b/target/linux/brcm2708/patches-4.4/0277-drm-vc4-Add-a-proper-short-circut-path-for-legacy-cu.patch
deleted file mode 100644
index 420cb6a..0000000
--- a/target/linux/brcm2708/patches-4.4/0277-drm-vc4-Add-a-proper-short-circut-path-for-legacy-cu.patch
+++ /dev/null
@@ -1,192 +0,0 @@
-From 056244a89e41317346558b66b30f7fe92e83a04d Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Wed, 30 Dec 2015 11:50:22 -0800
-Subject: [PATCH] drm/vc4: Add a proper short-circut path for legacy cursor
- updates.
-
-Previously, on every modeset we would allocate new display list
-memory, recompute changed planes, write all of them to the new memory,
-and pointed scanout at the new list (which will latch approximately at
-the next line of scanout). We let
-drm_atomic_helper_wait_for_vblanks() decide whether we needed to wait
-for a vblank after a modeset before cleaning up the old state and
-letting the next modeset proceed, and on legacy cursor updates we
-wouldn't wait. If you moved the cursor fast enough, we could
-potentially wrap around the display list memory area and overwrite the
-existing display list while it was still being scanned out, resulting
-in the HVS scanning out garbage or just halting.
-
-Instead of making cursor updates wait for scanout to move to the new
-display list area (which introduces significant cursor lag in X), we
-just rewrite our current display list.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 6674a904d68041d982ffb284d2827410765a097a)
----
- drivers/gpu/drm/vc4/vc4_kms.c | 9 ++++
- drivers/gpu/drm/vc4/vc4_plane.c | 94 ++++++++++++++++++++++++++++++++++++++---
- 2 files changed, 96 insertions(+), 7 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_kms.c
-+++ b/drivers/gpu/drm/vc4/vc4_kms.c
-@@ -49,6 +49,15 @@ vc4_atomic_complete_commit(struct vc4_co
-
- drm_atomic_helper_commit_modeset_enables(dev, state);
-
-+ /* Make sure that drm_atomic_helper_wait_for_vblanks()
-+ * actually waits for vblank. If we're doing a full atomic
-+ * modeset (as opposed to a vc4_update_plane() short circuit),
-+ * then we need to wait for scanout to be done with our
-+ * display lists before we free it and potentially reallocate
-+ * and overwrite the dlist memory with a new modeset.
-+ */
-+ state->legacy_cursor_update = false;
-+
- drm_atomic_helper_wait_for_vblanks(dev, state);
-
- drm_atomic_helper_cleanup_planes(dev, state);
---- a/drivers/gpu/drm/vc4/vc4_plane.c
-+++ b/drivers/gpu/drm/vc4/vc4_plane.c
-@@ -33,8 +33,12 @@ struct vc4_plane_state {
- u32 dlist_size; /* Number of dwords allocated for the display list */
- u32 dlist_count; /* Number of used dwords in the display list. */
-
-- /* Offset in the dlist to pointer word 0. */
-- u32 pw0_offset;
-+ /* Offset in the dlist to various words, for pageflip or
-+ * cursor updates.
-+ */
-+ u32 pos0_offset;
-+ u32 pos2_offset;
-+ u32 ptr0_offset;
-
- /* Offset where the plane's dlist was last stored in the
- * hardware at vc4_crtc_atomic_flush() time.
-@@ -239,6 +243,7 @@ static int vc4_plane_mode_set(struct drm
- SCALER_CTL0_UNITY);
-
- /* Position Word 0: Image Positions and Alpha Value */
-+ vc4_state->pos0_offset = vc4_state->dlist_count;
- vc4_dlist_write(vc4_state,
- VC4_SET_FIELD(0xff, SCALER_POS0_FIXED_ALPHA) |
- VC4_SET_FIELD(vc4_state->crtc_x, SCALER_POS0_START_X) |
-@@ -249,6 +254,7 @@ static int vc4_plane_mode_set(struct drm
- */
-
- /* Position Word 2: Source Image Size, Alpha Mode */
-+ vc4_state->pos2_offset = vc4_state->dlist_count;
- vc4_dlist_write(vc4_state,
- VC4_SET_FIELD(format->has_alpha ?
- SCALER_POS2_ALPHA_MODE_PIPELINE :
-@@ -260,9 +266,8 @@ static int vc4_plane_mode_set(struct drm
- /* Position Word 3: Context. Written by the HVS. */
- vc4_dlist_write(vc4_state, 0xc0c0c0c0);
-
-- vc4_state->pw0_offset = vc4_state->dlist_count;
--
- /* Pointer Word 0: RGB / Y Pointer */
-+ vc4_state->ptr0_offset = vc4_state->dlist_count;
- vc4_dlist_write(vc4_state, bo->paddr + vc4_state->offset);
-
- /* Pointer Context Word 0: Written by the HVS */
-@@ -348,13 +353,13 @@ void vc4_plane_async_set_fb(struct drm_p
- * scanout will start from this address as soon as the FIFO
- * needs to refill with pixels.
- */
-- writel(addr, &vc4_state->hw_dlist[vc4_state->pw0_offset]);
-+ writel(addr, &vc4_state->hw_dlist[vc4_state->ptr0_offset]);
-
- /* Also update the CPU-side dlist copy, so that any later
- * atomic updates that don't do a new modeset on our plane
- * also use our updated address.
- */
-- vc4_state->dlist[vc4_state->pw0_offset] = addr;
-+ vc4_state->dlist[vc4_state->ptr0_offset] = addr;
- }
-
- static const struct drm_plane_helper_funcs vc4_plane_helper_funcs = {
-@@ -370,8 +375,83 @@ static void vc4_plane_destroy(struct drm
- drm_plane_cleanup(plane);
- }
-
-+/* Implements immediate (non-vblank-synced) updates of the cursor
-+ * position, or falls back to the atomic helper otherwise.
-+ */
-+static int
-+vc4_update_plane(struct drm_plane *plane,
-+ struct drm_crtc *crtc,
-+ struct drm_framebuffer *fb,
-+ int crtc_x, int crtc_y,
-+ unsigned int crtc_w, unsigned int crtc_h,
-+ uint32_t src_x, uint32_t src_y,
-+ uint32_t src_w, uint32_t src_h)
-+{
-+ struct drm_plane_state *plane_state;
-+ struct vc4_plane_state *vc4_state;
-+
-+ if (plane != crtc->cursor)
-+ goto out;
-+
-+ plane_state = plane->state;
-+ vc4_state = to_vc4_plane_state(plane_state);
-+
-+ if (!plane_state)
-+ goto out;
-+
-+ /* If we're changing the cursor contents, do that in the
-+ * normal vblank-synced atomic path.
-+ */
-+ if (fb != plane_state->fb)
-+ goto out;
-+
-+ /* No configuring new scaling in the fast path. */
-+ if (crtc_w != plane_state->crtc_w ||
-+ crtc_h != plane_state->crtc_h ||
-+ src_w != plane_state->src_w ||
-+ src_h != plane_state->src_h) {
-+ goto out;
-+ }
-+
-+ /* Set the cursor's position on the screen. This is the
-+ * expected change from the drm_mode_cursor_universal()
-+ * helper.
-+ */
-+ plane_state->crtc_x = crtc_x;
-+ plane_state->crtc_y = crtc_y;
-+
-+ /* Allow changing the start position within the cursor BO, if
-+ * that matters.
-+ */
-+ plane_state->src_x = src_x;
-+ plane_state->src_y = src_y;
-+
-+ /* Update the display list based on the new crtc_x/y. */
-+ vc4_plane_atomic_check(plane, plane_state);
-+
-+ /* Note that we can't just call vc4_plane_write_dlist()
-+ * because that would smash the context data that the HVS is
-+ * currently using.
-+ */
-+ writel(vc4_state->dlist[vc4_state->pos0_offset],
-+ &vc4_state->hw_dlist[vc4_state->pos0_offset]);
-+ writel(vc4_state->dlist[vc4_state->pos2_offset],
-+ &vc4_state->hw_dlist[vc4_state->pos2_offset]);
-+ writel(vc4_state->dlist[vc4_state->ptr0_offset],
-+ &vc4_state->hw_dlist[vc4_state->ptr0_offset]);
-+
-+ return 0;
-+
-+out:
-+ return drm_atomic_helper_update_plane(plane, crtc, fb,
-+ crtc_x, crtc_y,
-+ crtc_w, crtc_h,
-+ src_x, src_y,
-+ src_w, src_h);
-+}
-+
- static const struct drm_plane_funcs vc4_plane_funcs = {
-- .update_plane = drm_atomic_helper_update_plane,
-+ .update_plane = vc4_update_plane,
- .disable_plane = drm_atomic_helper_disable_plane,
- .destroy = vc4_plane_destroy,
- .set_property = NULL,
diff --git a/target/linux/brcm2708/patches-4.4/0278-drm-vc4-Make-the-CRTCs-cooperate-on-allocating-displ.patch b/target/linux/brcm2708/patches-4.4/0278-drm-vc4-Make-the-CRTCs-cooperate-on-allocating-displ.patch
deleted file mode 100644
index 959bfce..0000000
--- a/target/linux/brcm2708/patches-4.4/0278-drm-vc4-Make-the-CRTCs-cooperate-on-allocating-displ.patch
+++ /dev/null
@@ -1,248 +0,0 @@
-From 94ede591f0db9d2c0d4c6c0175824cc6d5c38bd7 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 28 Dec 2015 13:25:41 -0800
-Subject: [PATCH] drm/vc4: Make the CRTCs cooperate on allocating display
- lists.
-
-So far, we've only ever lit up one CRTC, so this has been fine. To
-extend to more displays or more planes, we need to make sure we don't
-run our display lists into each other.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit d8dbf44f13b91185c618219d912b246817a8d132)
----
- drivers/gpu/drm/vc4/vc4_crtc.c | 115 +++++++++++++++++++++++------------------
- drivers/gpu/drm/vc4/vc4_drv.h | 8 ++-
- drivers/gpu/drm/vc4/vc4_hvs.c | 13 +++++
- 3 files changed, 84 insertions(+), 52 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_crtc.c
-+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
-@@ -49,22 +49,27 @@ struct vc4_crtc {
- /* Which HVS channel we're using for our CRTC. */
- int channel;
-
-- /* Pointer to the actual hardware display list memory for the
-- * crtc.
-- */
-- u32 __iomem *dlist;
--
-- u32 dlist_size; /* in dwords */
--
- struct drm_pending_vblank_event *event;
- };
-
-+struct vc4_crtc_state {
-+ struct drm_crtc_state base;
-+ /* Dlist area for this CRTC configuration. */
-+ struct drm_mm_node mm;
-+};
-+
- static inline struct vc4_crtc *
- to_vc4_crtc(struct drm_crtc *crtc)
- {
- return (struct vc4_crtc *)crtc;
- }
-
-+static inline struct vc4_crtc_state *
-+to_vc4_crtc_state(struct drm_crtc_state *crtc_state)
-+{
-+ return (struct vc4_crtc_state *)crtc_state;
-+}
-+
- struct vc4_crtc_data {
- /* Which channel of the HVS this pixelvalve sources from. */
- int hvs_channel;
-@@ -319,11 +324,13 @@ static void vc4_crtc_enable(struct drm_c
- static int vc4_crtc_atomic_check(struct drm_crtc *crtc,
- struct drm_crtc_state *state)
- {
-+ struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(state);
- struct drm_device *dev = crtc->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct drm_plane *plane;
-- struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
-+ unsigned long flags;
- u32 dlist_count = 0;
-+ int ret;
-
- /* The pixelvalve can only feed one encoder (and encoders are
- * 1:1 with connectors.)
-@@ -346,18 +353,12 @@ static int vc4_crtc_atomic_check(struct
-
- dlist_count++; /* Account for SCALER_CTL0_END. */
-
-- if (!vc4_crtc->dlist || dlist_count > vc4_crtc->dlist_size) {
-- vc4_crtc->dlist = ((u32 __iomem *)vc4->hvs->dlist +
-- HVS_BOOTLOADER_DLIST_END);
-- vc4_crtc->dlist_size = ((SCALER_DLIST_SIZE >> 2) -
-- HVS_BOOTLOADER_DLIST_END);
--
-- if (dlist_count > vc4_crtc->dlist_size) {
-- DRM_DEBUG_KMS("dlist too large for CRTC (%d > %d).\n",
-- dlist_count, vc4_crtc->dlist_size);
-- return -EINVAL;
-- }
-- }
-+ spin_lock_irqsave(&vc4->hvs->mm_lock, flags);
-+ ret = drm_mm_insert_node(&vc4->hvs->dlist_mm, &vc4_state->mm,
-+ dlist_count, 1, 0);
-+ spin_unlock_irqrestore(&vc4->hvs->mm_lock, flags);
-+ if (ret)
-+ return ret;
-
- return 0;
- }
-@@ -368,47 +369,29 @@ static void vc4_crtc_atomic_flush(struct
- struct drm_device *dev = crtc->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
-+ struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
- struct drm_plane *plane;
- bool debug_dump_regs = false;
-- u32 __iomem *dlist_next = vc4_crtc->dlist;
-+ u32 __iomem *dlist_start = vc4->hvs->dlist + vc4_state->mm.start;
-+ u32 __iomem *dlist_next = dlist_start;
-
- if (debug_dump_regs) {
- DRM_INFO("CRTC %d HVS before:\n", drm_crtc_index(crtc));
- vc4_hvs_dump_state(dev);
- }
-
-- /* Copy all the active planes' dlist contents to the hardware dlist.
-- *
-- * XXX: If the new display list was large enough that it
-- * overlapped a currently-read display list, we need to do
-- * something like disable scanout before putting in the new
-- * list. For now, we're safe because we only have the two
-- * planes.
-- */
-+ /* Copy all the active planes' dlist contents to the hardware dlist. */
- drm_atomic_crtc_for_each_plane(plane, crtc) {
- dlist_next += vc4_plane_write_dlist(plane, dlist_next);
- }
-
-- if (dlist_next == vc4_crtc->dlist) {
-- /* If no planes were enabled, use the SCALER_CTL0_END
-- * at the start of the display list memory (in the
-- * bootloader section). We'll rewrite that
-- * SCALER_CTL0_END, just in case, though.
-- */
-- writel(SCALER_CTL0_END, vc4->hvs->dlist);
-- HVS_WRITE(SCALER_DISPLISTX(vc4_crtc->channel), 0);
-- } else {
-- writel(SCALER_CTL0_END, dlist_next);
-- dlist_next++;
--
-- HVS_WRITE(SCALER_DISPLISTX(vc4_crtc->channel),
-- (u32 __iomem *)vc4_crtc->dlist -
-- (u32 __iomem *)vc4->hvs->dlist);
--
-- /* Make the next display list start after ours. */
-- vc4_crtc->dlist_size -= (dlist_next - vc4_crtc->dlist);
-- vc4_crtc->dlist = dlist_next;
-- }
-+ writel(SCALER_CTL0_END, dlist_next);
-+ dlist_next++;
-+
-+ WARN_ON_ONCE(dlist_next - dlist_start != vc4_state->mm.size);
-+
-+ HVS_WRITE(SCALER_DISPLISTX(vc4_crtc->channel),
-+ vc4_state->mm.start);
-
- if (debug_dump_regs) {
- DRM_INFO("CRTC %d HVS after:\n", drm_crtc_index(crtc));
-@@ -573,6 +556,36 @@ static int vc4_page_flip(struct drm_crtc
- return drm_atomic_helper_page_flip(crtc, fb, event, flags);
- }
-
-+static struct drm_crtc_state *vc4_crtc_duplicate_state(struct drm_crtc *crtc)
-+{
-+ struct vc4_crtc_state *vc4_state;
-+
-+ vc4_state = kzalloc(sizeof(*vc4_state), GFP_KERNEL);
-+ if (!vc4_state)
-+ return NULL;
-+
-+ __drm_atomic_helper_crtc_duplicate_state(crtc, &vc4_state->base);
-+ return &vc4_state->base;
-+}
-+
-+static void vc4_crtc_destroy_state(struct drm_crtc *crtc,
-+ struct drm_crtc_state *state)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(crtc->dev);
-+ struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(state);
-+
-+ if (vc4_state->mm.allocated) {
-+ unsigned long flags;
-+
-+ spin_lock_irqsave(&vc4->hvs->mm_lock, flags);
-+ drm_mm_remove_node(&vc4_state->mm);
-+ spin_unlock_irqrestore(&vc4->hvs->mm_lock, flags);
-+
-+ }
-+
-+ __drm_atomic_helper_crtc_destroy_state(crtc, state);
-+}
-+
- static const struct drm_crtc_funcs vc4_crtc_funcs = {
- .set_config = drm_atomic_helper_set_config,
- .destroy = vc4_crtc_destroy,
-@@ -581,8 +594,8 @@ static const struct drm_crtc_funcs vc4_c
- .cursor_set = NULL, /* handled by drm_mode_cursor_universal */
- .cursor_move = NULL, /* handled by drm_mode_cursor_universal */
- .reset = drm_atomic_helper_crtc_reset,
-- .atomic_duplicate_state = drm_atomic_helper_crtc_duplicate_state,
-- .atomic_destroy_state = drm_atomic_helper_crtc_destroy_state,
-+ .atomic_duplicate_state = vc4_crtc_duplicate_state,
-+ .atomic_destroy_state = vc4_crtc_destroy_state,
- };
-
- static const struct drm_crtc_helper_funcs vc4_crtc_helper_funcs = {
---- a/drivers/gpu/drm/vc4/vc4_drv.h
-+++ b/drivers/gpu/drm/vc4/vc4_drv.h
-@@ -150,7 +150,13 @@ struct vc4_v3d {
- struct vc4_hvs {
- struct platform_device *pdev;
- void __iomem *regs;
-- void __iomem *dlist;
-+ u32 __iomem *dlist;
-+
-+ /* Memory manager for CRTCs to allocate space in the display
-+ * list. Units are dwords.
-+ */
-+ struct drm_mm dlist_mm;
-+ spinlock_t mm_lock;
- };
-
- struct vc4_plane {
---- a/drivers/gpu/drm/vc4/vc4_hvs.c
-+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
-@@ -119,6 +119,17 @@ static int vc4_hvs_bind(struct device *d
-
- hvs->dlist = hvs->regs + SCALER_DLIST_START;
-
-+ spin_lock_init(&hvs->mm_lock);
-+
-+ /* Set up the HVS display list memory manager. We never
-+ * overwrite the setup from the bootloader (just 128b out of
-+ * our 16K), since we don't want to scramble the screen when
-+ * transitioning from the firmware's boot setup to runtime.
-+ */
-+ drm_mm_init(&hvs->dlist_mm,
-+ HVS_BOOTLOADER_DLIST_END,
-+ (SCALER_DLIST_SIZE >> 2) - HVS_BOOTLOADER_DLIST_END);
-+
- vc4->hvs = hvs;
- return 0;
- }
-@@ -129,6 +140,8 @@ static void vc4_hvs_unbind(struct device
- struct drm_device *drm = dev_get_drvdata(master);
- struct vc4_dev *vc4 = drm->dev_private;
-
-+ drm_mm_takedown(&vc4->hvs->dlist_mm);
-+
- vc4->hvs = NULL;
- }
-
diff --git a/target/linux/brcm2708/patches-4.4/0279-drm-vc4-Add-more-display-planes-to-each-CRTC.patch b/target/linux/brcm2708/patches-4.4/0279-drm-vc4-Add-more-display-planes-to-each-CRTC.patch
deleted file mode 100644
index 6c847f5..0000000
--- a/target/linux/brcm2708/patches-4.4/0279-drm-vc4-Add-more-display-planes-to-each-CRTC.patch
+++ /dev/null
@@ -1,106 +0,0 @@
-From befbfa7af4719d0496df2b79fbc4c8742e1b4ab4 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 20 Oct 2015 14:18:56 +0100
-Subject: [PATCH] drm/vc4: Add more display planes to each CRTC.
-
-Previously we only did the primary and cursor plane, but overlay
-planes are useful and just require this setup to add, since all planes
-go into the HVS display list in the same way.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit fc2d6f1eabee9d971453da2a27a72471c2a347dd)
----
- drivers/gpu/drm/vc4/vc4_crtc.c | 56 ++++++++++++++++++++++++++++++------------
- 1 file changed, 40 insertions(+), 16 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_crtc.c
-+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
-@@ -677,9 +677,9 @@ static int vc4_crtc_bind(struct device *
- struct vc4_dev *vc4 = to_vc4_dev(drm);
- struct vc4_crtc *vc4_crtc;
- struct drm_crtc *crtc;
-- struct drm_plane *primary_plane, *cursor_plane;
-+ struct drm_plane *primary_plane, *cursor_plane, *destroy_plane, *temp;
- const struct of_device_id *match;
-- int ret;
-+ int ret, i;
-
- vc4_crtc = devm_kzalloc(dev, sizeof(*vc4_crtc), GFP_KERNEL);
- if (!vc4_crtc)
-@@ -708,27 +708,49 @@ static int vc4_crtc_bind(struct device *
- goto err;
- }
-
-- cursor_plane = vc4_plane_init(drm, DRM_PLANE_TYPE_CURSOR);
-- if (IS_ERR(cursor_plane)) {
-- dev_err(dev, "failed to construct cursor plane\n");
-- ret = PTR_ERR(cursor_plane);
-- goto err_primary;
-- }
--
-- drm_crtc_init_with_planes(drm, crtc, primary_plane, cursor_plane,
-+ drm_crtc_init_with_planes(drm, crtc, primary_plane, NULL,
- &vc4_crtc_funcs);
- drm_crtc_helper_add(crtc, &vc4_crtc_helper_funcs);
- primary_plane->crtc = crtc;
-- cursor_plane->crtc = crtc;
- vc4->crtc[drm_crtc_index(crtc)] = vc4_crtc;
- vc4_crtc->channel = vc4_crtc->data->hvs_channel;
-
-+ /* Set up some arbitrary number of planes. We're not limited
-+ * by a set number of physical registers, just the space in
-+ * the HVS (16k) and how small an plane can be (28 bytes).
-+ * However, each plane we set up takes up some memory, and
-+ * increases the cost of looping over planes, which atomic
-+ * modesetting does quite a bit. As a result, we pick a
-+ * modest number of planes to expose, that should hopefully
-+ * still cover any sane usecase.
-+ */
-+ for (i = 0; i < 8; i++) {
-+ struct drm_plane *plane =
-+ vc4_plane_init(drm, DRM_PLANE_TYPE_OVERLAY);
-+
-+ if (IS_ERR(plane))
-+ continue;
-+
-+ plane->possible_crtcs = 1 << drm_crtc_index(crtc);
-+ }
-+
-+ /* Set up the legacy cursor after overlay initialization,
-+ * since we overlay planes on the CRTC in the order they were
-+ * initialized.
-+ */
-+ cursor_plane = vc4_plane_init(drm, DRM_PLANE_TYPE_CURSOR);
-+ if (!IS_ERR(cursor_plane)) {
-+ cursor_plane->possible_crtcs = 1 << drm_crtc_index(crtc);
-+ cursor_plane->crtc = crtc;
-+ crtc->cursor = cursor_plane;
-+ }
-+
- CRTC_WRITE(PV_INTEN, 0);
- CRTC_WRITE(PV_INTSTAT, PV_INT_VFP_START);
- ret = devm_request_irq(dev, platform_get_irq(pdev, 0),
- vc4_crtc_irq_handler, 0, "vc4 crtc", vc4_crtc);
- if (ret)
-- goto err_cursor;
-+ goto err_destroy_planes;
-
- vc4_set_crtc_possible_masks(drm, crtc);
-
-@@ -736,10 +758,12 @@ static int vc4_crtc_bind(struct device *
-
- return 0;
-
--err_cursor:
-- cursor_plane->funcs->destroy(cursor_plane);
--err_primary:
-- primary_plane->funcs->destroy(primary_plane);
-+err_destroy_planes:
-+ list_for_each_entry_safe(destroy_plane, temp,
-+ &drm->mode_config.plane_list, head) {
-+ if (destroy_plane->possible_crtcs == 1 << drm_crtc_index(crtc))
-+ destroy_plane->funcs->destroy(destroy_plane);
-+ }
- err:
- return ret;
- }
diff --git a/target/linux/brcm2708/patches-4.4/0280-drm-vc4-Fix-which-value-is-being-used-for-source-ima.patch b/target/linux/brcm2708/patches-4.4/0280-drm-vc4-Fix-which-value-is-being-used-for-source-ima.patch
deleted file mode 100644
index 6fc1985..0000000
--- a/target/linux/brcm2708/patches-4.4/0280-drm-vc4-Fix-which-value-is-being-used-for-source-ima.patch
+++ /dev/null
@@ -1,76 +0,0 @@
-From 567ed250293747ceb5413faba8ae1f6c3d207bee Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 28 Dec 2015 14:45:25 -0800
-Subject: [PATCH] drm/vc4: Fix which value is being used for source image size.
-
-This doesn't matter yet since we only allow 1:1 scaling, but the
-comment clearly says we should be using the source size.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit f863e356013d628fa65b1cd89aa298eed26fc936)
----
- drivers/gpu/drm/vc4/vc4_plane.c | 23 ++++++++++++++---------
- 1 file changed, 14 insertions(+), 9 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_plane.c
-+++ b/drivers/gpu/drm/vc4/vc4_plane.c
-@@ -47,6 +47,8 @@ struct vc4_plane_state {
-
- /* Clipped coordinates of the plane on the display. */
- int crtc_x, crtc_y, crtc_w, crtc_h;
-+ /* Clipped size of the area scanned from in the FB. */
-+ u32 src_w, src_h;
-
- /* Offset to start scanning out from the start of the plane's
- * BO.
-@@ -186,11 +188,6 @@ static int vc4_plane_setup_clipping_and_
-
- vc4_state->offset = fb->offsets[0];
-
-- vc4_state->crtc_x = state->crtc_x;
-- vc4_state->crtc_y = state->crtc_y;
-- vc4_state->crtc_w = state->crtc_w;
-- vc4_state->crtc_h = state->crtc_h;
--
- if (state->crtc_w << 16 != state->src_w ||
- state->crtc_h << 16 != state->src_h) {
- /* We don't support scaling yet, which involves
-@@ -201,17 +198,25 @@ static int vc4_plane_setup_clipping_and_
- return -EINVAL;
- }
-
-+ vc4_state->src_w = state->src_w >> 16;
-+ vc4_state->src_h = state->src_h >> 16;
-+
-+ vc4_state->crtc_x = state->crtc_x;
-+ vc4_state->crtc_y = state->crtc_y;
-+ vc4_state->crtc_w = state->crtc_w;
-+ vc4_state->crtc_h = state->crtc_h;
-+
- if (vc4_state->crtc_x < 0) {
- vc4_state->offset += (drm_format_plane_cpp(fb->pixel_format,
- 0) *
- -vc4_state->crtc_x);
-- vc4_state->crtc_w += vc4_state->crtc_x;
-+ vc4_state->src_w += vc4_state->crtc_x;
- vc4_state->crtc_x = 0;
- }
-
- if (vc4_state->crtc_y < 0) {
- vc4_state->offset += fb->pitches[0] * -vc4_state->crtc_y;
-- vc4_state->crtc_h += vc4_state->crtc_y;
-+ vc4_state->src_h += vc4_state->crtc_y;
- vc4_state->crtc_y = 0;
- }
-
-@@ -260,8 +265,8 @@ static int vc4_plane_mode_set(struct drm
- SCALER_POS2_ALPHA_MODE_PIPELINE :
- SCALER_POS2_ALPHA_MODE_FIXED,
- SCALER_POS2_ALPHA_MODE) |
-- VC4_SET_FIELD(vc4_state->crtc_w, SCALER_POS2_WIDTH) |
-- VC4_SET_FIELD(vc4_state->crtc_h, SCALER_POS2_HEIGHT));
-+ VC4_SET_FIELD(vc4_state->src_w, SCALER_POS2_WIDTH) |
-+ VC4_SET_FIELD(vc4_state->src_h, SCALER_POS2_HEIGHT));
-
- /* Position Word 3: Context. Written by the HVS. */
- vc4_dlist_write(vc4_state, 0xc0c0c0c0);
diff --git a/target/linux/brcm2708/patches-4.4/0281-drm-vc4-Add-support-for-scaling-of-display-planes.patch b/target/linux/brcm2708/patches-4.4/0281-drm-vc4-Add-support-for-scaling-of-display-planes.patch
deleted file mode 100644
index c174573..0000000
--- a/target/linux/brcm2708/patches-4.4/0281-drm-vc4-Add-support-for-scaling-of-display-planes.patch
+++ /dev/null
@@ -1,579 +0,0 @@
-From 5a7984aba2d7c7cb50bbfb84e36b2f5d3f0dc46d Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 20 Oct 2015 16:06:57 +0100
-Subject: [PATCH] drm/vc4: Add support for scaling of display planes.
-
-This implements a simple policy for choosing scaling modes
-(trapezoidal for decimation, PPF for magnification), and a single PPF
-filter (Mitchell/Netravali's recommendation).
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 21af94cf1a4c2d3450ab7fead58e6e2291ab92a9)
----
- drivers/gpu/drm/vc4/vc4_drv.h | 4 +
- drivers/gpu/drm/vc4/vc4_hvs.c | 84 +++++++++++++
- drivers/gpu/drm/vc4/vc4_plane.c | 253 +++++++++++++++++++++++++++++++++++++---
- drivers/gpu/drm/vc4/vc4_regs.h | 46 ++++++++
- 4 files changed, 374 insertions(+), 13 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_drv.h
-+++ b/drivers/gpu/drm/vc4/vc4_drv.h
-@@ -156,7 +156,11 @@ struct vc4_hvs {
- * list. Units are dwords.
- */
- struct drm_mm dlist_mm;
-+ /* Memory manager for the LBM memory used by HVS scaling. */
-+ struct drm_mm lbm_mm;
- spinlock_t mm_lock;
-+
-+ struct drm_mm_node mitchell_netravali_filter;
- };
-
- struct vc4_plane {
---- a/drivers/gpu/drm/vc4/vc4_hvs.c
-+++ b/drivers/gpu/drm/vc4/vc4_hvs.c
-@@ -100,12 +100,76 @@ int vc4_hvs_debugfs_regs(struct seq_file
- }
- #endif
-
-+/* The filter kernel is composed of dwords each containing 3 9-bit
-+ * signed integers packed next to each other.
-+ */
-+#define VC4_INT_TO_COEFF(coeff) (coeff & 0x1ff)
-+#define VC4_PPF_FILTER_WORD(c0, c1, c2) \
-+ ((((c0) & 0x1ff) << 0) | \
-+ (((c1) & 0x1ff) << 9) | \
-+ (((c2) & 0x1ff) << 18))
-+
-+/* The whole filter kernel is arranged as the coefficients 0-16 going
-+ * up, then a pad, then 17-31 going down and reversed within the
-+ * dwords. This means that a linear phase kernel (where it's
-+ * symmetrical at the boundary between 15 and 16) has the last 5
-+ * dwords matching the first 5, but reversed.
-+ */
-+#define VC4_LINEAR_PHASE_KERNEL(c0, c1, c2, c3, c4, c5, c6, c7, c8, \
-+ c9, c10, c11, c12, c13, c14, c15) \
-+ {VC4_PPF_FILTER_WORD(c0, c1, c2), \
-+ VC4_PPF_FILTER_WORD(c3, c4, c5), \
-+ VC4_PPF_FILTER_WORD(c6, c7, c8), \
-+ VC4_PPF_FILTER_WORD(c9, c10, c11), \
-+ VC4_PPF_FILTER_WORD(c12, c13, c14), \
-+ VC4_PPF_FILTER_WORD(c15, c15, 0)}
-+
-+#define VC4_LINEAR_PHASE_KERNEL_DWORDS 6
-+#define VC4_KERNEL_DWORDS (VC4_LINEAR_PHASE_KERNEL_DWORDS * 2 - 1)
-+
-+/* Recommended B=1/3, C=1/3 filter choice from Mitchell/Netravali.
-+ * http://www.cs.utexas.edu/~fussell/courses/cs384g/lectures/mitchell/Mitchell.pdf
-+ */
-+static const u32 mitchell_netravali_1_3_1_3_kernel[] =
-+ VC4_LINEAR_PHASE_KERNEL(0, -2, -6, -8, -10, -8, -3, 2, 18,
-+ 50, 82, 119, 155, 187, 213, 227);
-+
-+static int vc4_hvs_upload_linear_kernel(struct vc4_hvs *hvs,
-+ struct drm_mm_node *space,
-+ const u32 *kernel)
-+{
-+ int ret, i;
-+ u32 __iomem *dst_kernel;
-+
-+ ret = drm_mm_insert_node(&hvs->dlist_mm, space, VC4_KERNEL_DWORDS, 1,
-+ 0);
-+ if (ret) {
-+ DRM_ERROR("Failed to allocate space for filter kernel: %d\n",
-+ ret);
-+ return ret;
-+ }
-+
-+ dst_kernel = hvs->dlist + space->start;
-+
-+ for (i = 0; i < VC4_KERNEL_DWORDS; i++) {
-+ if (i < VC4_LINEAR_PHASE_KERNEL_DWORDS)
-+ writel(kernel[i], &dst_kernel[i]);
-+ else {
-+ writel(kernel[VC4_KERNEL_DWORDS - i - 1],
-+ &dst_kernel[i]);
-+ }
-+ }
-+
-+ return 0;
-+}
-+
- static int vc4_hvs_bind(struct device *dev, struct device *master, void *data)
- {
- struct platform_device *pdev = to_platform_device(dev);
- struct drm_device *drm = dev_get_drvdata(master);
- struct vc4_dev *vc4 = drm->dev_private;
- struct vc4_hvs *hvs = NULL;
-+ int ret;
-
- hvs = devm_kzalloc(&pdev->dev, sizeof(*hvs), GFP_KERNEL);
- if (!hvs)
-@@ -130,6 +194,22 @@ static int vc4_hvs_bind(struct device *d
- HVS_BOOTLOADER_DLIST_END,
- (SCALER_DLIST_SIZE >> 2) - HVS_BOOTLOADER_DLIST_END);
-
-+ /* Set up the HVS LBM memory manager. We could have some more
-+ * complicated data structure that allowed reuse of LBM areas
-+ * between planes when they don't overlap on the screen, but
-+ * for now we just allocate globally.
-+ */
-+ drm_mm_init(&hvs->lbm_mm, 0, 96 * 1024);
-+
-+ /* Upload filter kernels. We only have the one for now, so we
-+ * keep it around for the lifetime of the driver.
-+ */
-+ ret = vc4_hvs_upload_linear_kernel(hvs,
-+ &hvs->mitchell_netravali_filter,
-+ mitchell_netravali_1_3_1_3_kernel);
-+ if (ret)
-+ return ret;
-+
- vc4->hvs = hvs;
- return 0;
- }
-@@ -140,7 +220,11 @@ static void vc4_hvs_unbind(struct device
- struct drm_device *drm = dev_get_drvdata(master);
- struct vc4_dev *vc4 = drm->dev_private;
-
-+ if (vc4->hvs->mitchell_netravali_filter.allocated)
-+ drm_mm_remove_node(&vc4->hvs->mitchell_netravali_filter);
-+
- drm_mm_takedown(&vc4->hvs->dlist_mm);
-+ drm_mm_takedown(&vc4->hvs->lbm_mm);
-
- vc4->hvs = NULL;
- }
---- a/drivers/gpu/drm/vc4/vc4_plane.c
-+++ b/drivers/gpu/drm/vc4/vc4_plane.c
-@@ -24,6 +24,12 @@
- #include "drm_fb_cma_helper.h"
- #include "drm_plane_helper.h"
-
-+enum vc4_scaling_mode {
-+ VC4_SCALING_NONE,
-+ VC4_SCALING_TPZ,
-+ VC4_SCALING_PPF,
-+};
-+
- struct vc4_plane_state {
- struct drm_plane_state base;
- /* System memory copy of the display list for this element, computed
-@@ -47,13 +53,19 @@ struct vc4_plane_state {
-
- /* Clipped coordinates of the plane on the display. */
- int crtc_x, crtc_y, crtc_w, crtc_h;
-- /* Clipped size of the area scanned from in the FB. */
-- u32 src_w, src_h;
-+ /* Clipped area being scanned from in the FB. */
-+ u32 src_x, src_y, src_w, src_h;
-+
-+ enum vc4_scaling_mode x_scaling, y_scaling;
-+ bool is_unity;
-
- /* Offset to start scanning out from the start of the plane's
- * BO.
- */
- u32 offset;
-+
-+ /* Our allocation in LBM for temporary storage during scaling. */
-+ struct drm_mm_node lbm;
- };
-
- static inline struct vc4_plane_state *
-@@ -106,6 +118,16 @@ static const struct hvs_format *vc4_get_
- return NULL;
- }
-
-+static enum vc4_scaling_mode vc4_get_scaling_mode(u32 src, u32 dst)
-+{
-+ if (dst > src)
-+ return VC4_SCALING_PPF;
-+ else if (dst < src)
-+ return VC4_SCALING_TPZ;
-+ else
-+ return VC4_SCALING_NONE;
-+}
-+
- static bool plane_enabled(struct drm_plane_state *state)
- {
- return state->fb && state->crtc;
-@@ -122,6 +144,8 @@ static struct drm_plane_state *vc4_plane
- if (!vc4_state)
- return NULL;
-
-+ memset(&vc4_state->lbm, 0, sizeof(vc4_state->lbm));
-+
- __drm_atomic_helper_plane_duplicate_state(plane, &vc4_state->base);
-
- if (vc4_state->dlist) {
-@@ -141,8 +165,17 @@ static struct drm_plane_state *vc4_plane
- static void vc4_plane_destroy_state(struct drm_plane *plane,
- struct drm_plane_state *state)
- {
-+ struct vc4_dev *vc4 = to_vc4_dev(plane->dev);
- struct vc4_plane_state *vc4_state = to_vc4_plane_state(state);
-
-+ if (vc4_state->lbm.allocated) {
-+ unsigned long irqflags;
-+
-+ spin_lock_irqsave(&vc4->hvs->mm_lock, irqflags);
-+ drm_mm_remove_node(&vc4_state->lbm);
-+ spin_unlock_irqrestore(&vc4->hvs->mm_lock, irqflags);
-+ }
-+
- kfree(vc4_state->dlist);
- __drm_atomic_helper_plane_destroy_state(plane, &vc4_state->base);
- kfree(state);
-@@ -181,23 +214,60 @@ static void vc4_dlist_write(struct vc4_p
- vc4_state->dlist[vc4_state->dlist_count++] = val;
- }
-
-+/* Returns the scl0/scl1 field based on whether the dimensions need to
-+ * be up/down/non-scaled.
-+ *
-+ * This is a replication of a table from the spec.
-+ */
-+static u32 vc4_get_scl_field(struct drm_plane_state *state)
-+{
-+ struct vc4_plane_state *vc4_state = to_vc4_plane_state(state);
-+
-+ switch (vc4_state->x_scaling << 2 | vc4_state->y_scaling) {
-+ case VC4_SCALING_PPF << 2 | VC4_SCALING_PPF:
-+ return SCALER_CTL0_SCL_H_PPF_V_PPF;
-+ case VC4_SCALING_TPZ << 2 | VC4_SCALING_PPF:
-+ return SCALER_CTL0_SCL_H_TPZ_V_PPF;
-+ case VC4_SCALING_PPF << 2 | VC4_SCALING_TPZ:
-+ return SCALER_CTL0_SCL_H_PPF_V_TPZ;
-+ case VC4_SCALING_TPZ << 2 | VC4_SCALING_TPZ:
-+ return SCALER_CTL0_SCL_H_TPZ_V_TPZ;
-+ case VC4_SCALING_PPF << 2 | VC4_SCALING_NONE:
-+ return SCALER_CTL0_SCL_H_PPF_V_NONE;
-+ case VC4_SCALING_NONE << 2 | VC4_SCALING_PPF:
-+ return SCALER_CTL0_SCL_H_NONE_V_PPF;
-+ case VC4_SCALING_NONE << 2 | VC4_SCALING_TPZ:
-+ return SCALER_CTL0_SCL_H_NONE_V_TPZ;
-+ case VC4_SCALING_TPZ << 2 | VC4_SCALING_NONE:
-+ return SCALER_CTL0_SCL_H_TPZ_V_NONE;
-+ default:
-+ case VC4_SCALING_NONE << 2 | VC4_SCALING_NONE:
-+ /* The unity case is independently handled by
-+ * SCALER_CTL0_UNITY.
-+ */
-+ return 0;
-+ }
-+}
-+
- static int vc4_plane_setup_clipping_and_scaling(struct drm_plane_state *state)
- {
-+ struct drm_plane *plane = state->plane;
- struct vc4_plane_state *vc4_state = to_vc4_plane_state(state);
- struct drm_framebuffer *fb = state->fb;
-+ u32 subpixel_src_mask = (1 << 16) - 1;
-
- vc4_state->offset = fb->offsets[0];
-
-- if (state->crtc_w << 16 != state->src_w ||
-- state->crtc_h << 16 != state->src_h) {
-- /* We don't support scaling yet, which involves
-- * allocating the LBM memory for scaling temporary
-- * storage, and putting filter kernels in the HVS
-- * context.
-- */
-+ /* We don't support subpixel source positioning for scaling. */
-+ if ((state->src_x & subpixel_src_mask) ||
-+ (state->src_y & subpixel_src_mask) ||
-+ (state->src_w & subpixel_src_mask) ||
-+ (state->src_h & subpixel_src_mask)) {
- return -EINVAL;
- }
-
-+ vc4_state->src_x = state->src_x >> 16;
-+ vc4_state->src_y = state->src_y >> 16;
- vc4_state->src_w = state->src_w >> 16;
- vc4_state->src_h = state->src_h >> 16;
-
-@@ -206,6 +276,23 @@ static int vc4_plane_setup_clipping_and_
- vc4_state->crtc_w = state->crtc_w;
- vc4_state->crtc_h = state->crtc_h;
-
-+ vc4_state->x_scaling = vc4_get_scaling_mode(vc4_state->src_w,
-+ vc4_state->crtc_w);
-+ vc4_state->y_scaling = vc4_get_scaling_mode(vc4_state->src_h,
-+ vc4_state->crtc_h);
-+ vc4_state->is_unity = (vc4_state->x_scaling == VC4_SCALING_NONE &&
-+ vc4_state->y_scaling == VC4_SCALING_NONE);
-+
-+ /* No configuring scaling on the cursor plane, since it gets
-+ non-vblank-synced updates, and scaling requires requires
-+ LBM changes which have to be vblank-synced.
-+ */
-+ if (plane->type == DRM_PLANE_TYPE_CURSOR && !vc4_state->is_unity)
-+ return -EINVAL;
-+
-+ /* Clamp the on-screen start x/y to 0. The hardware doesn't
-+ * support negative y, and negative x wastes bandwidth.
-+ */
- if (vc4_state->crtc_x < 0) {
- vc4_state->offset += (drm_format_plane_cpp(fb->pixel_format,
- 0) *
-@@ -223,6 +310,87 @@ static int vc4_plane_setup_clipping_and_
- return 0;
- }
-
-+static void vc4_write_tpz(struct vc4_plane_state *vc4_state, u32 src, u32 dst)
-+{
-+ u32 scale, recip;
-+
-+ scale = (1 << 16) * src / dst;
-+
-+ /* The specs note that while the reciprocal would be defined
-+ * as (1<<32)/scale, ~0 is close enough.
-+ */
-+ recip = ~0 / scale;
-+
-+ vc4_dlist_write(vc4_state,
-+ VC4_SET_FIELD(scale, SCALER_TPZ0_SCALE) |
-+ VC4_SET_FIELD(0, SCALER_TPZ0_IPHASE));
-+ vc4_dlist_write(vc4_state,
-+ VC4_SET_FIELD(recip, SCALER_TPZ1_RECIP));
-+}
-+
-+static void vc4_write_ppf(struct vc4_plane_state *vc4_state, u32 src, u32 dst)
-+{
-+ u32 scale = (1 << 16) * src / dst;
-+
-+ vc4_dlist_write(vc4_state,
-+ SCALER_PPF_AGC |
-+ VC4_SET_FIELD(scale, SCALER_PPF_SCALE) |
-+ VC4_SET_FIELD(0, SCALER_PPF_IPHASE));
-+}
-+
-+static u32 vc4_lbm_size(struct drm_plane_state *state)
-+{
-+ struct vc4_plane_state *vc4_state = to_vc4_plane_state(state);
-+ /* This is the worst case number. One of the two sizes will
-+ * be used depending on the scaling configuration.
-+ */
-+ u32 pix_per_line = max(vc4_state->src_w, (u32)vc4_state->crtc_w);
-+ u32 lbm;
-+
-+ if (vc4_state->is_unity)
-+ return 0;
-+ else if (vc4_state->y_scaling == VC4_SCALING_TPZ)
-+ lbm = pix_per_line * 8;
-+ else {
-+ /* In special cases, this multiplier might be 12. */
-+ lbm = pix_per_line * 16;
-+ }
-+
-+ lbm = roundup(lbm, 32);
-+
-+ return lbm;
-+}
-+
-+static void vc4_write_scaling_parameters(struct drm_plane_state *state)
-+{
-+ struct vc4_plane_state *vc4_state = to_vc4_plane_state(state);
-+
-+ /* Ch0 H-PPF Word 0: Scaling Parameters */
-+ if (vc4_state->x_scaling == VC4_SCALING_PPF) {
-+ vc4_write_ppf(vc4_state,
-+ vc4_state->src_w, vc4_state->crtc_w);
-+ }
-+
-+ /* Ch0 V-PPF Words 0-1: Scaling Parameters, Context */
-+ if (vc4_state->y_scaling == VC4_SCALING_PPF) {
-+ vc4_write_ppf(vc4_state,
-+ vc4_state->src_h, vc4_state->crtc_h);
-+ vc4_dlist_write(vc4_state, 0xc0c0c0c0);
-+ }
-+
-+ /* Ch0 H-TPZ Words 0-1: Scaling Parameters, Recip */
-+ if (vc4_state->x_scaling == VC4_SCALING_TPZ) {
-+ vc4_write_tpz(vc4_state,
-+ vc4_state->src_w, vc4_state->crtc_w);
-+ }
-+
-+ /* Ch0 V-TPZ Words 0-2: Scaling Parameters, Recip, Context */
-+ if (vc4_state->y_scaling == VC4_SCALING_TPZ) {
-+ vc4_write_tpz(vc4_state,
-+ vc4_state->src_h, vc4_state->crtc_h);
-+ vc4_dlist_write(vc4_state, 0xc0c0c0c0);
-+ }
-+}
-
- /* Writes out a full display list for an active plane to the plane's
- * private dlist state.
-@@ -230,22 +398,50 @@ static int vc4_plane_setup_clipping_and_
- static int vc4_plane_mode_set(struct drm_plane *plane,
- struct drm_plane_state *state)
- {
-+ struct vc4_dev *vc4 = to_vc4_dev(plane->dev);
- struct vc4_plane_state *vc4_state = to_vc4_plane_state(state);
- struct drm_framebuffer *fb = state->fb;
- struct drm_gem_cma_object *bo = drm_fb_cma_get_gem_obj(fb, 0);
- u32 ctl0_offset = vc4_state->dlist_count;
- const struct hvs_format *format = vc4_get_hvs_format(fb->pixel_format);
-+ u32 scl;
-+ u32 lbm_size;
-+ unsigned long irqflags;
- int ret;
-
- ret = vc4_plane_setup_clipping_and_scaling(state);
- if (ret)
- return ret;
-
-+ /* Allocate the LBM memory that the HVS will use for temporary
-+ * storage due to our scaling/format conversion.
-+ */
-+ lbm_size = vc4_lbm_size(state);
-+ if (lbm_size) {
-+ if (!vc4_state->lbm.allocated) {
-+ spin_lock_irqsave(&vc4->hvs->mm_lock, irqflags);
-+ ret = drm_mm_insert_node(&vc4->hvs->lbm_mm,
-+ &vc4_state->lbm,
-+ lbm_size, 32, 0);
-+ spin_unlock_irqrestore(&vc4->hvs->mm_lock, irqflags);
-+ } else {
-+ WARN_ON_ONCE(lbm_size != vc4_state->lbm.size);
-+ }
-+ }
-+
-+ if (ret)
-+ return ret;
-+
-+ scl = vc4_get_scl_field(state);
-+
-+ /* Control word */
- vc4_dlist_write(vc4_state,
- SCALER_CTL0_VALID |
- (format->pixel_order << SCALER_CTL0_ORDER_SHIFT) |
- (format->hvs << SCALER_CTL0_PIXEL_FORMAT_SHIFT) |
-- SCALER_CTL0_UNITY);
-+ (vc4_state->is_unity ? SCALER_CTL0_UNITY : 0) |
-+ VC4_SET_FIELD(scl, SCALER_CTL0_SCL0) |
-+ VC4_SET_FIELD(scl, SCALER_CTL0_SCL1));
-
- /* Position Word 0: Image Positions and Alpha Value */
- vc4_state->pos0_offset = vc4_state->dlist_count;
-@@ -254,9 +450,14 @@ static int vc4_plane_mode_set(struct drm
- VC4_SET_FIELD(vc4_state->crtc_x, SCALER_POS0_START_X) |
- VC4_SET_FIELD(vc4_state->crtc_y, SCALER_POS0_START_Y));
-
-- /* Position Word 1: Scaled Image Dimensions.
-- * Skipped due to SCALER_CTL0_UNITY scaling.
-- */
-+ /* Position Word 1: Scaled Image Dimensions. */
-+ if (!vc4_state->is_unity) {
-+ vc4_dlist_write(vc4_state,
-+ VC4_SET_FIELD(vc4_state->crtc_w,
-+ SCALER_POS1_SCL_WIDTH) |
-+ VC4_SET_FIELD(vc4_state->crtc_h,
-+ SCALER_POS1_SCL_HEIGHT));
-+ }
-
- /* Position Word 2: Source Image Size, Alpha Mode */
- vc4_state->pos2_offset = vc4_state->dlist_count;
-@@ -282,6 +483,32 @@ static int vc4_plane_mode_set(struct drm
- vc4_dlist_write(vc4_state,
- VC4_SET_FIELD(fb->pitches[0], SCALER_SRC_PITCH));
-
-+ if (!vc4_state->is_unity) {
-+ /* LBM Base Address. */
-+ if (vc4_state->y_scaling != VC4_SCALING_NONE)
-+ vc4_dlist_write(vc4_state, vc4_state->lbm.start);
-+
-+ vc4_write_scaling_parameters(state);
-+
-+ /* If any PPF setup was done, then all the kernel
-+ * pointers get uploaded.
-+ */
-+ if (vc4_state->x_scaling == VC4_SCALING_PPF ||
-+ vc4_state->y_scaling == VC4_SCALING_PPF) {
-+ u32 kernel = VC4_SET_FIELD(vc4->hvs->mitchell_netravali_filter.start,
-+ SCALER_PPF_KERNEL_OFFSET);
-+
-+ /* HPPF plane 0 */
-+ vc4_dlist_write(vc4_state, kernel);
-+ /* VPPF plane 0 */
-+ vc4_dlist_write(vc4_state, kernel);
-+ /* HPPF plane 1 */
-+ vc4_dlist_write(vc4_state, kernel);
-+ /* VPPF plane 1 */
-+ vc4_dlist_write(vc4_state, kernel);
-+ }
-+ }
-+
- vc4_state->dlist[ctl0_offset] |=
- VC4_SET_FIELD(vc4_state->dlist_count, SCALER_CTL0_SIZE);
-
---- a/drivers/gpu/drm/vc4/vc4_regs.h
-+++ b/drivers/gpu/drm/vc4/vc4_regs.h
-@@ -536,6 +536,21 @@ enum hvs_pixel_format {
- #define SCALER_CTL0_ORDER_MASK VC4_MASK(14, 13)
- #define SCALER_CTL0_ORDER_SHIFT 13
-
-+#define SCALER_CTL0_SCL1_MASK VC4_MASK(10, 8)
-+#define SCALER_CTL0_SCL1_SHIFT 8
-+
-+#define SCALER_CTL0_SCL0_MASK VC4_MASK(7, 5)
-+#define SCALER_CTL0_SCL0_SHIFT 5
-+
-+#define SCALER_CTL0_SCL_H_PPF_V_PPF 0
-+#define SCALER_CTL0_SCL_H_TPZ_V_PPF 1
-+#define SCALER_CTL0_SCL_H_PPF_V_TPZ 2
-+#define SCALER_CTL0_SCL_H_TPZ_V_TPZ 3
-+#define SCALER_CTL0_SCL_H_PPF_V_NONE 4
-+#define SCALER_CTL0_SCL_H_NONE_V_PPF 5
-+#define SCALER_CTL0_SCL_H_NONE_V_TPZ 6
-+#define SCALER_CTL0_SCL_H_TPZ_V_NONE 7
-+
- /* Set to indicate no scaling. */
- #define SCALER_CTL0_UNITY BIT(4)
-
-@@ -551,6 +566,12 @@ enum hvs_pixel_format {
- #define SCALER_POS0_START_X_MASK VC4_MASK(11, 0)
- #define SCALER_POS0_START_X_SHIFT 0
-
-+#define SCALER_POS1_SCL_HEIGHT_MASK VC4_MASK(27, 16)
-+#define SCALER_POS1_SCL_HEIGHT_SHIFT 16
-+
-+#define SCALER_POS1_SCL_WIDTH_MASK VC4_MASK(11, 0)
-+#define SCALER_POS1_SCL_WIDTH_SHIFT 0
-+
- #define SCALER_POS2_ALPHA_MODE_MASK VC4_MASK(31, 30)
- #define SCALER_POS2_ALPHA_MODE_SHIFT 30
- #define SCALER_POS2_ALPHA_MODE_PIPELINE 0
-@@ -564,6 +585,31 @@ enum hvs_pixel_format {
- #define SCALER_POS2_WIDTH_MASK VC4_MASK(11, 0)
- #define SCALER_POS2_WIDTH_SHIFT 0
-
-+#define SCALER_TPZ0_VERT_RECALC BIT(31)
-+#define SCALER_TPZ0_SCALE_MASK VC4_MASK(28, 8)
-+#define SCALER_TPZ0_SCALE_SHIFT 8
-+#define SCALER_TPZ0_IPHASE_MASK VC4_MASK(7, 0)
-+#define SCALER_TPZ0_IPHASE_SHIFT 0
-+#define SCALER_TPZ1_RECIP_MASK VC4_MASK(15, 0)
-+#define SCALER_TPZ1_RECIP_SHIFT 0
-+
-+/* Skips interpolating coefficients to 64 phases, so just 8 are used.
-+ * Required for nearest neighbor.
-+ */
-+#define SCALER_PPF_NOINTERP BIT(31)
-+/* Replaes the highest valued coefficient with one that makes all 4
-+ * sum to unity.
-+ */
-+#define SCALER_PPF_AGC BIT(30)
-+#define SCALER_PPF_SCALE_MASK VC4_MASK(24, 8)
-+#define SCALER_PPF_SCALE_SHIFT 8
-+#define SCALER_PPF_IPHASE_MASK VC4_MASK(6, 0)
-+#define SCALER_PPF_IPHASE_SHIFT 0
-+
-+#define SCALER_PPF_KERNEL_OFFSET_MASK VC4_MASK(13, 0)
-+#define SCALER_PPF_KERNEL_OFFSET_SHIFT 0
-+#define SCALER_PPF_KERNEL_UNCACHED BIT(31)
-+
- #define SCALER_SRC_PITCH_MASK VC4_MASK(15, 0)
- #define SCALER_SRC_PITCH_SHIFT 0
-
diff --git a/target/linux/brcm2708/patches-4.4/0282-drm-vc4-Add-support-for-YUV-planes.patch b/target/linux/brcm2708/patches-4.4/0282-drm-vc4-Add-support-for-YUV-planes.patch
deleted file mode 100644
index bec1c2b..0000000
--- a/target/linux/brcm2708/patches-4.4/0282-drm-vc4-Add-support-for-YUV-planes.patch
+++ /dev/null
@@ -1,519 +0,0 @@
-From 08d0e437e351c8be6ce7985854fe4405e214664a Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Wed, 30 Dec 2015 12:25:44 -0800
-Subject: [PATCH] drm/vc4: Add support for YUV planes.
-
-This supports 420 and 422 subsampling with 2 or 3 planes, tested with
-modetest. It doesn't set up chroma subsampling position (which it
-appears KMS doesn't deal with yet).
-
-The LBM memory is overallocated in many cases, but apparently the docs
-aren't quite correct and I'll probably need to look at the hardware
-source to really figure it out.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit fc04023fafecf19ebd09278d8d67dc5ed1f68b46)
----
- drivers/gpu/drm/vc4/vc4_plane.c | 256 +++++++++++++++++++++++++++++++---------
- drivers/gpu/drm/vc4/vc4_regs.h | 56 ++++++++-
- 2 files changed, 253 insertions(+), 59 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_plane.c
-+++ b/drivers/gpu/drm/vc4/vc4_plane.c
-@@ -54,15 +54,19 @@ struct vc4_plane_state {
- /* Clipped coordinates of the plane on the display. */
- int crtc_x, crtc_y, crtc_w, crtc_h;
- /* Clipped area being scanned from in the FB. */
-- u32 src_x, src_y, src_w, src_h;
-+ u32 src_x, src_y;
-
-- enum vc4_scaling_mode x_scaling, y_scaling;
-+ u32 src_w[2], src_h[2];
-+
-+ /* Scaling selection for the RGB/Y plane and the Cb/Cr planes. */
-+ enum vc4_scaling_mode x_scaling[2], y_scaling[2];
- bool is_unity;
-+ bool is_yuv;
-
- /* Offset to start scanning out from the start of the plane's
- * BO.
- */
-- u32 offset;
-+ u32 offsets[3];
-
- /* Our allocation in LBM for temporary storage during scaling. */
- struct drm_mm_node lbm;
-@@ -79,6 +83,7 @@ static const struct hvs_format {
- u32 hvs; /* HVS_FORMAT_* */
- u32 pixel_order;
- bool has_alpha;
-+ bool flip_cbcr;
- } hvs_formats[] = {
- {
- .drm = DRM_FORMAT_XRGB8888, .hvs = HVS_PIXEL_FORMAT_RGBA8888,
-@@ -104,6 +109,32 @@ static const struct hvs_format {
- .drm = DRM_FORMAT_XRGB1555, .hvs = HVS_PIXEL_FORMAT_RGBA5551,
- .pixel_order = HVS_PIXEL_ORDER_ABGR, .has_alpha = false,
- },
-+ {
-+ .drm = DRM_FORMAT_YUV422,
-+ .hvs = HVS_PIXEL_FORMAT_YCBCR_YUV422_3PLANE,
-+ },
-+ {
-+ .drm = DRM_FORMAT_YVU422,
-+ .hvs = HVS_PIXEL_FORMAT_YCBCR_YUV422_3PLANE,
-+ .flip_cbcr = true,
-+ },
-+ {
-+ .drm = DRM_FORMAT_YUV420,
-+ .hvs = HVS_PIXEL_FORMAT_YCBCR_YUV420_3PLANE,
-+ },
-+ {
-+ .drm = DRM_FORMAT_YVU420,
-+ .hvs = HVS_PIXEL_FORMAT_YCBCR_YUV420_3PLANE,
-+ .flip_cbcr = true,
-+ },
-+ {
-+ .drm = DRM_FORMAT_NV12,
-+ .hvs = HVS_PIXEL_FORMAT_YCBCR_YUV420_2PLANE,
-+ },
-+ {
-+ .drm = DRM_FORMAT_NV16,
-+ .hvs = HVS_PIXEL_FORMAT_YCBCR_YUV422_2PLANE,
-+ },
- };
-
- static const struct hvs_format *vc4_get_hvs_format(u32 drm_format)
-@@ -219,11 +250,11 @@ static void vc4_dlist_write(struct vc4_p
- *
- * This is a replication of a table from the spec.
- */
--static u32 vc4_get_scl_field(struct drm_plane_state *state)
-+static u32 vc4_get_scl_field(struct drm_plane_state *state, int plane)
- {
- struct vc4_plane_state *vc4_state = to_vc4_plane_state(state);
-
-- switch (vc4_state->x_scaling << 2 | vc4_state->y_scaling) {
-+ switch (vc4_state->x_scaling[plane] << 2 | vc4_state->y_scaling[plane]) {
- case VC4_SCALING_PPF << 2 | VC4_SCALING_PPF:
- return SCALER_CTL0_SCL_H_PPF_V_PPF;
- case VC4_SCALING_TPZ << 2 | VC4_SCALING_PPF:
-@@ -254,9 +285,16 @@ static int vc4_plane_setup_clipping_and_
- struct drm_plane *plane = state->plane;
- struct vc4_plane_state *vc4_state = to_vc4_plane_state(state);
- struct drm_framebuffer *fb = state->fb;
-+ struct drm_gem_cma_object *bo = drm_fb_cma_get_gem_obj(fb, 0);
- u32 subpixel_src_mask = (1 << 16) - 1;
-+ u32 format = fb->pixel_format;
-+ int num_planes = drm_format_num_planes(format);
-+ u32 h_subsample = 1;
-+ u32 v_subsample = 1;
-+ int i;
-
-- vc4_state->offset = fb->offsets[0];
-+ for (i = 0; i < num_planes; i++)
-+ vc4_state->offsets[i] = bo->paddr + fb->offsets[i];
-
- /* We don't support subpixel source positioning for scaling. */
- if ((state->src_x & subpixel_src_mask) ||
-@@ -268,20 +306,48 @@ static int vc4_plane_setup_clipping_and_
-
- vc4_state->src_x = state->src_x >> 16;
- vc4_state->src_y = state->src_y >> 16;
-- vc4_state->src_w = state->src_w >> 16;
-- vc4_state->src_h = state->src_h >> 16;
-+ vc4_state->src_w[0] = state->src_w >> 16;
-+ vc4_state->src_h[0] = state->src_h >> 16;
-
- vc4_state->crtc_x = state->crtc_x;
- vc4_state->crtc_y = state->crtc_y;
- vc4_state->crtc_w = state->crtc_w;
- vc4_state->crtc_h = state->crtc_h;
-
-- vc4_state->x_scaling = vc4_get_scaling_mode(vc4_state->src_w,
-- vc4_state->crtc_w);
-- vc4_state->y_scaling = vc4_get_scaling_mode(vc4_state->src_h,
-- vc4_state->crtc_h);
-- vc4_state->is_unity = (vc4_state->x_scaling == VC4_SCALING_NONE &&
-- vc4_state->y_scaling == VC4_SCALING_NONE);
-+ vc4_state->x_scaling[0] = vc4_get_scaling_mode(vc4_state->src_w[0],
-+ vc4_state->crtc_w);
-+ vc4_state->y_scaling[0] = vc4_get_scaling_mode(vc4_state->src_h[0],
-+ vc4_state->crtc_h);
-+
-+ if (num_planes > 1) {
-+ vc4_state->is_yuv = true;
-+
-+ h_subsample = drm_format_horz_chroma_subsampling(format);
-+ v_subsample = drm_format_vert_chroma_subsampling(format);
-+ vc4_state->src_w[1] = vc4_state->src_w[0] / h_subsample;
-+ vc4_state->src_h[1] = vc4_state->src_h[0] / v_subsample;
-+
-+ vc4_state->x_scaling[1] =
-+ vc4_get_scaling_mode(vc4_state->src_w[1],
-+ vc4_state->crtc_w);
-+ vc4_state->y_scaling[1] =
-+ vc4_get_scaling_mode(vc4_state->src_h[1],
-+ vc4_state->crtc_h);
-+
-+ /* YUV conversion requires that scaling be enabled,
-+ * even on a plane that's otherwise 1:1. Choose TPZ
-+ * for simplicity.
-+ */
-+ if (vc4_state->x_scaling[0] == VC4_SCALING_NONE)
-+ vc4_state->x_scaling[0] = VC4_SCALING_TPZ;
-+ if (vc4_state->y_scaling[0] == VC4_SCALING_NONE)
-+ vc4_state->y_scaling[0] = VC4_SCALING_TPZ;
-+ }
-+
-+ vc4_state->is_unity = (vc4_state->x_scaling[0] == VC4_SCALING_NONE &&
-+ vc4_state->y_scaling[0] == VC4_SCALING_NONE &&
-+ vc4_state->x_scaling[1] == VC4_SCALING_NONE &&
-+ vc4_state->y_scaling[1] == VC4_SCALING_NONE);
-
- /* No configuring scaling on the cursor plane, since it gets
- non-vblank-synced updates, and scaling requires requires
-@@ -294,16 +360,27 @@ static int vc4_plane_setup_clipping_and_
- * support negative y, and negative x wastes bandwidth.
- */
- if (vc4_state->crtc_x < 0) {
-- vc4_state->offset += (drm_format_plane_cpp(fb->pixel_format,
-- 0) *
-- -vc4_state->crtc_x);
-- vc4_state->src_w += vc4_state->crtc_x;
-+ for (i = 0; i < num_planes; i++) {
-+ u32 cpp = drm_format_plane_cpp(fb->pixel_format, i);
-+ u32 subs = ((i == 0) ? 1 : h_subsample);
-+
-+ vc4_state->offsets[i] += (cpp *
-+ (-vc4_state->crtc_x) / subs);
-+ }
-+ vc4_state->src_w[0] += vc4_state->crtc_x;
-+ vc4_state->src_w[1] += vc4_state->crtc_x / h_subsample;
- vc4_state->crtc_x = 0;
- }
-
- if (vc4_state->crtc_y < 0) {
-- vc4_state->offset += fb->pitches[0] * -vc4_state->crtc_y;
-- vc4_state->src_h += vc4_state->crtc_y;
-+ for (i = 0; i < num_planes; i++) {
-+ u32 subs = ((i == 0) ? 1 : v_subsample);
-+
-+ vc4_state->offsets[i] += (fb->pitches[i] *
-+ (-vc4_state->crtc_y) / subs);
-+ }
-+ vc4_state->src_h[0] += vc4_state->crtc_y;
-+ vc4_state->src_h[1] += vc4_state->crtc_y / v_subsample;
- vc4_state->crtc_y = 0;
- }
-
-@@ -344,15 +421,23 @@ static u32 vc4_lbm_size(struct drm_plane
- /* This is the worst case number. One of the two sizes will
- * be used depending on the scaling configuration.
- */
-- u32 pix_per_line = max(vc4_state->src_w, (u32)vc4_state->crtc_w);
-+ u32 pix_per_line = max(vc4_state->src_w[0], (u32)vc4_state->crtc_w);
- u32 lbm;
-
-- if (vc4_state->is_unity)
-- return 0;
-- else if (vc4_state->y_scaling == VC4_SCALING_TPZ)
-- lbm = pix_per_line * 8;
-- else {
-- /* In special cases, this multiplier might be 12. */
-+ if (!vc4_state->is_yuv) {
-+ if (vc4_state->is_unity)
-+ return 0;
-+ else if (vc4_state->y_scaling[0] == VC4_SCALING_TPZ)
-+ lbm = pix_per_line * 8;
-+ else {
-+ /* In special cases, this multiplier might be 12. */
-+ lbm = pix_per_line * 16;
-+ }
-+ } else {
-+ /* There are cases for this going down to a multiplier
-+ * of 2, but according to the firmware source, the
-+ * table in the docs is somewhat wrong.
-+ */
- lbm = pix_per_line * 16;
- }
-
-@@ -361,33 +446,34 @@ static u32 vc4_lbm_size(struct drm_plane
- return lbm;
- }
-
--static void vc4_write_scaling_parameters(struct drm_plane_state *state)
-+static void vc4_write_scaling_parameters(struct drm_plane_state *state,
-+ int channel)
- {
- struct vc4_plane_state *vc4_state = to_vc4_plane_state(state);
-
- /* Ch0 H-PPF Word 0: Scaling Parameters */
-- if (vc4_state->x_scaling == VC4_SCALING_PPF) {
-+ if (vc4_state->x_scaling[channel] == VC4_SCALING_PPF) {
- vc4_write_ppf(vc4_state,
-- vc4_state->src_w, vc4_state->crtc_w);
-+ vc4_state->src_w[channel], vc4_state->crtc_w);
- }
-
- /* Ch0 V-PPF Words 0-1: Scaling Parameters, Context */
-- if (vc4_state->y_scaling == VC4_SCALING_PPF) {
-+ if (vc4_state->y_scaling[channel] == VC4_SCALING_PPF) {
- vc4_write_ppf(vc4_state,
-- vc4_state->src_h, vc4_state->crtc_h);
-+ vc4_state->src_h[channel], vc4_state->crtc_h);
- vc4_dlist_write(vc4_state, 0xc0c0c0c0);
- }
-
- /* Ch0 H-TPZ Words 0-1: Scaling Parameters, Recip */
-- if (vc4_state->x_scaling == VC4_SCALING_TPZ) {
-+ if (vc4_state->x_scaling[channel] == VC4_SCALING_TPZ) {
- vc4_write_tpz(vc4_state,
-- vc4_state->src_w, vc4_state->crtc_w);
-+ vc4_state->src_w[channel], vc4_state->crtc_w);
- }
-
- /* Ch0 V-TPZ Words 0-2: Scaling Parameters, Recip, Context */
-- if (vc4_state->y_scaling == VC4_SCALING_TPZ) {
-+ if (vc4_state->y_scaling[channel] == VC4_SCALING_TPZ) {
- vc4_write_tpz(vc4_state,
-- vc4_state->src_h, vc4_state->crtc_h);
-+ vc4_state->src_h[channel], vc4_state->crtc_h);
- vc4_dlist_write(vc4_state, 0xc0c0c0c0);
- }
- }
-@@ -401,13 +487,13 @@ static int vc4_plane_mode_set(struct drm
- struct vc4_dev *vc4 = to_vc4_dev(plane->dev);
- struct vc4_plane_state *vc4_state = to_vc4_plane_state(state);
- struct drm_framebuffer *fb = state->fb;
-- struct drm_gem_cma_object *bo = drm_fb_cma_get_gem_obj(fb, 0);
- u32 ctl0_offset = vc4_state->dlist_count;
- const struct hvs_format *format = vc4_get_hvs_format(fb->pixel_format);
-- u32 scl;
-+ int num_planes = drm_format_num_planes(format->drm);
-+ u32 scl0, scl1;
- u32 lbm_size;
- unsigned long irqflags;
-- int ret;
-+ int ret, i;
-
- ret = vc4_plane_setup_clipping_and_scaling(state);
- if (ret)
-@@ -432,7 +518,19 @@ static int vc4_plane_mode_set(struct drm
- if (ret)
- return ret;
-
-- scl = vc4_get_scl_field(state);
-+ /* SCL1 is used for Cb/Cr scaling of planar formats. For RGB
-+ * and 4:4:4, scl1 should be set to scl0 so both channels of
-+ * the scaler do the same thing. For YUV, the Y plane needs
-+ * to be put in channel 1 and Cb/Cr in channel 0, so we swap
-+ * the scl fields here.
-+ */
-+ if (num_planes == 1) {
-+ scl0 = vc4_get_scl_field(state, 1);
-+ scl1 = scl0;
-+ } else {
-+ scl0 = vc4_get_scl_field(state, 1);
-+ scl1 = vc4_get_scl_field(state, 0);
-+ }
-
- /* Control word */
- vc4_dlist_write(vc4_state,
-@@ -440,8 +538,8 @@ static int vc4_plane_mode_set(struct drm
- (format->pixel_order << SCALER_CTL0_ORDER_SHIFT) |
- (format->hvs << SCALER_CTL0_PIXEL_FORMAT_SHIFT) |
- (vc4_state->is_unity ? SCALER_CTL0_UNITY : 0) |
-- VC4_SET_FIELD(scl, SCALER_CTL0_SCL0) |
-- VC4_SET_FIELD(scl, SCALER_CTL0_SCL1));
-+ VC4_SET_FIELD(scl0, SCALER_CTL0_SCL0) |
-+ VC4_SET_FIELD(scl1, SCALER_CTL0_SCL1));
-
- /* Position Word 0: Image Positions and Alpha Value */
- vc4_state->pos0_offset = vc4_state->dlist_count;
-@@ -466,35 +564,68 @@ static int vc4_plane_mode_set(struct drm
- SCALER_POS2_ALPHA_MODE_PIPELINE :
- SCALER_POS2_ALPHA_MODE_FIXED,
- SCALER_POS2_ALPHA_MODE) |
-- VC4_SET_FIELD(vc4_state->src_w, SCALER_POS2_WIDTH) |
-- VC4_SET_FIELD(vc4_state->src_h, SCALER_POS2_HEIGHT));
-+ VC4_SET_FIELD(vc4_state->src_w[0], SCALER_POS2_WIDTH) |
-+ VC4_SET_FIELD(vc4_state->src_h[0], SCALER_POS2_HEIGHT));
-
- /* Position Word 3: Context. Written by the HVS. */
- vc4_dlist_write(vc4_state, 0xc0c0c0c0);
-
-- /* Pointer Word 0: RGB / Y Pointer */
-+
-+ /* Pointer Word 0/1/2: RGB / Y / Cb / Cr Pointers
-+ *
-+ * The pointers may be any byte address.
-+ */
- vc4_state->ptr0_offset = vc4_state->dlist_count;
-- vc4_dlist_write(vc4_state, bo->paddr + vc4_state->offset);
-+ if (!format->flip_cbcr) {
-+ for (i = 0; i < num_planes; i++)
-+ vc4_dlist_write(vc4_state, vc4_state->offsets[i]);
-+ } else {
-+ WARN_ON_ONCE(num_planes != 3);
-+ vc4_dlist_write(vc4_state, vc4_state->offsets[0]);
-+ vc4_dlist_write(vc4_state, vc4_state->offsets[2]);
-+ vc4_dlist_write(vc4_state, vc4_state->offsets[1]);
-+ }
-
-- /* Pointer Context Word 0: Written by the HVS */
-- vc4_dlist_write(vc4_state, 0xc0c0c0c0);
-+ /* Pointer Context Word 0/1/2: Written by the HVS */
-+ for (i = 0; i < num_planes; i++)
-+ vc4_dlist_write(vc4_state, 0xc0c0c0c0);
-
-- /* Pitch word 0: Pointer 0 Pitch */
-- vc4_dlist_write(vc4_state,
-- VC4_SET_FIELD(fb->pitches[0], SCALER_SRC_PITCH));
-+ /* Pitch word 0/1/2 */
-+ for (i = 0; i < num_planes; i++) {
-+ vc4_dlist_write(vc4_state,
-+ VC4_SET_FIELD(fb->pitches[i], SCALER_SRC_PITCH));
-+ }
-+
-+ /* Colorspace conversion words */
-+ if (vc4_state->is_yuv) {
-+ vc4_dlist_write(vc4_state, SCALER_CSC0_ITR_R_601_5);
-+ vc4_dlist_write(vc4_state, SCALER_CSC1_ITR_R_601_5);
-+ vc4_dlist_write(vc4_state, SCALER_CSC2_ITR_R_601_5);
-+ }
-
- if (!vc4_state->is_unity) {
- /* LBM Base Address. */
-- if (vc4_state->y_scaling != VC4_SCALING_NONE)
-+ if (vc4_state->y_scaling[0] != VC4_SCALING_NONE ||
-+ vc4_state->y_scaling[1] != VC4_SCALING_NONE) {
- vc4_dlist_write(vc4_state, vc4_state->lbm.start);
-+ }
-
-- vc4_write_scaling_parameters(state);
-+ if (num_planes > 1) {
-+ /* Emit Cb/Cr as channel 0 and Y as channel
-+ * 1. This matches how we set up scl0/scl1
-+ * above.
-+ */
-+ vc4_write_scaling_parameters(state, 1);
-+ }
-+ vc4_write_scaling_parameters(state, 0);
-
- /* If any PPF setup was done, then all the kernel
- * pointers get uploaded.
- */
-- if (vc4_state->x_scaling == VC4_SCALING_PPF ||
-- vc4_state->y_scaling == VC4_SCALING_PPF) {
-+ if (vc4_state->x_scaling[0] == VC4_SCALING_PPF ||
-+ vc4_state->y_scaling[0] == VC4_SCALING_PPF ||
-+ vc4_state->x_scaling[1] == VC4_SCALING_PPF ||
-+ vc4_state->y_scaling[1] == VC4_SCALING_PPF) {
- u32 kernel = VC4_SET_FIELD(vc4->hvs->mitchell_netravali_filter.start,
- SCALER_PPF_KERNEL_OFFSET);
-
-@@ -698,6 +829,7 @@ struct drm_plane *vc4_plane_init(struct
- struct drm_plane *plane = NULL;
- struct vc4_plane *vc4_plane;
- u32 formats[ARRAY_SIZE(hvs_formats)];
-+ u32 num_formats = 0;
- int ret = 0;
- unsigned i;
-
-@@ -708,12 +840,20 @@ struct drm_plane *vc4_plane_init(struct
- goto fail;
- }
-
-- for (i = 0; i < ARRAY_SIZE(hvs_formats); i++)
-- formats[i] = hvs_formats[i].drm;
-+ for (i = 0; i < ARRAY_SIZE(hvs_formats); i++) {
-+ /* Don't allow YUV in cursor planes, since that means
-+ * tuning on the scaler, which we don't allow for the
-+ * cursor.
-+ */
-+ if (type != DRM_PLANE_TYPE_CURSOR ||
-+ hvs_formats[i].hvs < HVS_PIXEL_FORMAT_YCBCR_YUV420_3PLANE) {
-+ formats[num_formats++] = hvs_formats[i].drm;
-+ }
-+ }
- plane = &vc4_plane->base;
- ret = drm_universal_plane_init(dev, plane, 0xff,
- &vc4_plane_funcs,
-- formats, ARRAY_SIZE(formats),
-+ formats, num_formats,
- type);
-
- drm_plane_helper_add(plane, &vc4_plane_helper_funcs);
---- a/drivers/gpu/drm/vc4/vc4_regs.h
-+++ b/drivers/gpu/drm/vc4/vc4_regs.h
-@@ -503,7 +503,12 @@ enum hvs_pixel_format {
- HVS_PIXEL_FORMAT_RGB888 = 5,
- HVS_PIXEL_FORMAT_RGBA6666 = 6,
- /* 32bpp */
-- HVS_PIXEL_FORMAT_RGBA8888 = 7
-+ HVS_PIXEL_FORMAT_RGBA8888 = 7,
-+
-+ HVS_PIXEL_FORMAT_YCBCR_YUV420_3PLANE = 8,
-+ HVS_PIXEL_FORMAT_YCBCR_YUV420_2PLANE = 9,
-+ HVS_PIXEL_FORMAT_YCBCR_YUV422_3PLANE = 10,
-+ HVS_PIXEL_FORMAT_YCBCR_YUV422_2PLANE = 11,
- };
-
- /* Note: the LSB is the rightmost character shown. Only valid for
-@@ -585,6 +590,55 @@ enum hvs_pixel_format {
- #define SCALER_POS2_WIDTH_MASK VC4_MASK(11, 0)
- #define SCALER_POS2_WIDTH_SHIFT 0
-
-+/* Color Space Conversion words. Some values are S2.8 signed
-+ * integers, except that the 2 integer bits map as {0x0: 0, 0x1: 1,
-+ * 0x2: 2, 0x3: -1}
-+ */
-+/* bottom 8 bits of S2.8 contribution of Cr to Blue */
-+#define SCALER_CSC0_COEF_CR_BLU_MASK VC4_MASK(31, 24)
-+#define SCALER_CSC0_COEF_CR_BLU_SHIFT 24
-+/* Signed offset to apply to Y before CSC. (Y' = Y + YY_OFS) */
-+#define SCALER_CSC0_COEF_YY_OFS_MASK VC4_MASK(23, 16)
-+#define SCALER_CSC0_COEF_YY_OFS_SHIFT 16
-+/* Signed offset to apply to CB before CSC (Cb' = Cb - 128 + CB_OFS). */
-+#define SCALER_CSC0_COEF_CB_OFS_MASK VC4_MASK(15, 8)
-+#define SCALER_CSC0_COEF_CB_OFS_SHIFT 8
-+/* Signed offset to apply to CB before CSC (Cr' = Cr - 128 + CR_OFS). */
-+#define SCALER_CSC0_COEF_CR_OFS_MASK VC4_MASK(7, 0)
-+#define SCALER_CSC0_COEF_CR_OFS_SHIFT 0
-+#define SCALER_CSC0_ITR_R_601_5 0x00f00000
-+#define SCALER_CSC0_ITR_R_709_3 0x00f00000
-+#define SCALER_CSC0_JPEG_JFIF 0x00000000
-+
-+/* S2.8 contribution of Cb to Green */
-+#define SCALER_CSC1_COEF_CB_GRN_MASK VC4_MASK(31, 22)
-+#define SCALER_CSC1_COEF_CB_GRN_SHIFT 22
-+/* S2.8 contribution of Cr to Green */
-+#define SCALER_CSC1_COEF_CR_GRN_MASK VC4_MASK(21, 12)
-+#define SCALER_CSC1_COEF_CR_GRN_SHIFT 12
-+/* S2.8 contribution of Y to all of RGB */
-+#define SCALER_CSC1_COEF_YY_ALL_MASK VC4_MASK(11, 2)
-+#define SCALER_CSC1_COEF_YY_ALL_SHIFT 2
-+/* top 2 bits of S2.8 contribution of Cr to Blue */
-+#define SCALER_CSC1_COEF_CR_BLU_MASK VC4_MASK(1, 0)
-+#define SCALER_CSC1_COEF_CR_BLU_SHIFT 0
-+#define SCALER_CSC1_ITR_R_601_5 0xe73304a8
-+#define SCALER_CSC1_ITR_R_709_3 0xf2b784a8
-+#define SCALER_CSC1_JPEG_JFIF 0xea34a400
-+
-+/* S2.8 contribution of Cb to Red */
-+#define SCALER_CSC2_COEF_CB_RED_MASK VC4_MASK(29, 20)
-+#define SCALER_CSC2_COEF_CB_RED_SHIFT 20
-+/* S2.8 contribution of Cr to Red */
-+#define SCALER_CSC2_COEF_CR_RED_MASK VC4_MASK(19, 10)
-+#define SCALER_CSC2_COEF_CR_RED_SHIFT 10
-+/* S2.8 contribution of Cb to Blue */
-+#define SCALER_CSC2_COEF_CB_BLU_MASK VC4_MASK(19, 10)
-+#define SCALER_CSC2_COEF_CB_BLU_SHIFT 10
-+#define SCALER_CSC2_ITR_R_601_5 0x00066204
-+#define SCALER_CSC2_ITR_R_709_3 0x00072a1c
-+#define SCALER_CSC2_JPEG_JFIF 0x000599c5
-+
- #define SCALER_TPZ0_VERT_RECALC BIT(31)
- #define SCALER_TPZ0_SCALE_MASK VC4_MASK(28, 8)
- #define SCALER_TPZ0_SCALE_SHIFT 8
diff --git a/target/linux/brcm2708/patches-4.4/0283-drm-vc4-Fix-spurious-GPU-resets-due-to-BO-reuse.patch b/target/linux/brcm2708/patches-4.4/0283-drm-vc4-Fix-spurious-GPU-resets-due-to-BO-reuse.patch
deleted file mode 100644
index e6e3335..0000000
--- a/target/linux/brcm2708/patches-4.4/0283-drm-vc4-Fix-spurious-GPU-resets-due-to-BO-reuse.patch
+++ /dev/null
@@ -1,81 +0,0 @@
-From 20399eb8527bfb74406fe7af056ed7af0cc9f277 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 8 Feb 2016 11:19:14 -0800
-Subject: [PATCH] drm/vc4: Fix spurious GPU resets due to BO reuse.
-
-We were tracking the "where are the head pointers pointing" globally,
-so if another job reused the same BOs and execution was at the same
-point as last time we checked, we'd stop and trigger a reset even
-though the GPU had made progress.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit c4ce60dc30912df09b2438f1e5594eae1ef64d1e)
----
- drivers/gpu/drm/vc4/vc4_drv.h | 6 +++++-
- drivers/gpu/drm/vc4/vc4_gem.c | 19 ++++++++++++++-----
- 2 files changed, 19 insertions(+), 6 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_drv.h
-+++ b/drivers/gpu/drm/vc4/vc4_drv.h
-@@ -93,7 +93,6 @@ struct vc4_dev {
- struct work_struct overflow_mem_work;
-
- struct {
-- uint32_t last_ct0ca, last_ct1ca;
- struct timer_list timer;
- struct work_struct reset_work;
- } hangcheck;
-@@ -203,6 +202,11 @@ struct vc4_exec_info {
- /* Sequence number for this bin/render job. */
- uint64_t seqno;
-
-+ /* Last current addresses the hardware was processing when the
-+ * hangcheck timer checked on us.
-+ */
-+ uint32_t last_ct0ca, last_ct1ca;
-+
- /* Kernel-space copy of the ioctl arguments */
- struct drm_vc4_submit_cl *args;
-
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -271,10 +271,17 @@ vc4_hangcheck_elapsed(unsigned long data
- struct drm_device *dev = (struct drm_device *)data;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- uint32_t ct0ca, ct1ca;
-+ unsigned long irqflags;
-+ struct vc4_exec_info *exec;
-+
-+ spin_lock_irqsave(&vc4->job_lock, irqflags);
-+ exec = vc4_first_job(vc4);
-
- /* If idle, we can stop watching for hangs. */
-- if (list_empty(&vc4->job_list))
-+ if (!exec) {
-+ spin_unlock_irqrestore(&vc4->job_lock, irqflags);
- return;
-+ }
-
- ct0ca = V3D_READ(V3D_CTNCA(0));
- ct1ca = V3D_READ(V3D_CTNCA(1));
-@@ -282,14 +289,16 @@ vc4_hangcheck_elapsed(unsigned long data
- /* If we've made any progress in execution, rearm the timer
- * and wait.
- */
-- if (ct0ca != vc4->hangcheck.last_ct0ca ||
-- ct1ca != vc4->hangcheck.last_ct1ca) {
-- vc4->hangcheck.last_ct0ca = ct0ca;
-- vc4->hangcheck.last_ct1ca = ct1ca;
-+ if (ct0ca != exec->last_ct0ca || ct1ca != exec->last_ct1ca) {
-+ exec->last_ct0ca = ct0ca;
-+ exec->last_ct1ca = ct1ca;
-+ spin_unlock_irqrestore(&vc4->job_lock, irqflags);
- vc4_queue_hangcheck(dev);
- return;
- }
-
-+ spin_unlock_irqrestore(&vc4->job_lock, irqflags);
-+
- /* We've gone too long with no progress, reset. This has to
- * be done from a work struct, since resetting can sleep and
- * this timer hook isn't allowed to.
diff --git a/target/linux/brcm2708/patches-4.4/0284-drm-vc4-Fix-a-framebuffer-reference-leak-on-async-fl.patch b/target/linux/brcm2708/patches-4.4/0284-drm-vc4-Fix-a-framebuffer-reference-leak-on-async-fl.patch
deleted file mode 100644
index 2873913..0000000
--- a/target/linux/brcm2708/patches-4.4/0284-drm-vc4-Fix-a-framebuffer-reference-leak-on-async-fl.patch
+++ /dev/null
@@ -1,26 +0,0 @@
-From 85e5b58da528a7b32bf3a570b31f46129f2ecea9 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 5 Feb 2016 15:06:15 -0800
-Subject: [PATCH] drm/vc4: Fix a framebuffer reference leak on async flip
- interrupt.
-
-We'd need X to queue up an async pageflip while another is
-outstanding, and then take a SIGIO. I think X actually avoids sending
-out the next pageflip while one's already queued, but I'm not sure.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 48627eb8dc55c60d35794105f6f79fb627347dbd)
----
- drivers/gpu/drm/vc4/vc4_crtc.c | 1 +
- 1 file changed, 1 insertion(+)
-
---- a/drivers/gpu/drm/vc4/vc4_crtc.c
-+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
-@@ -527,6 +527,7 @@ static int vc4_async_page_flip(struct dr
- /* Make sure all other async modesetes have landed. */
- ret = down_interruptible(&vc4->async_modeset);
- if (ret) {
-+ drm_framebuffer_unreference(fb);
- kfree(flip_state);
- return ret;
- }
diff --git a/target/linux/brcm2708/patches-4.4/0285-drm-vc4-Bring-HDMI-up-from-power-off-if-necessary.patch b/target/linux/brcm2708/patches-4.4/0285-drm-vc4-Bring-HDMI-up-from-power-off-if-necessary.patch
deleted file mode 100644
index 9754dee..0000000
--- a/target/linux/brcm2708/patches-4.4/0285-drm-vc4-Bring-HDMI-up-from-power-off-if-necessary.patch
+++ /dev/null
@@ -1,72 +0,0 @@
-From 72babc2af3130870d9ef1ccfdf61224a8e834935 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 12 Feb 2016 14:15:14 -0800
-Subject: [PATCH] drm/vc4: Bring HDMI up from power off if necessary.
-
-If the firmware hadn't brought up HDMI for us, we need to do its
-power-on reset sequence (reset HD and and clear its STANDBY bits,
-reset HDMI, and leave the PHY disabled).
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 851479ad5927b7b1aa141ca9dedb897a7bce2b1d)
----
- drivers/gpu/drm/vc4/vc4_hdmi.c | 29 ++++++++++++++++++++++++++++-
- drivers/gpu/drm/vc4/vc4_regs.h | 2 ++
- 2 files changed, 30 insertions(+), 1 deletion(-)
-
---- a/drivers/gpu/drm/vc4/vc4_hdmi.c
-+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
-@@ -497,6 +497,16 @@ static int vc4_hdmi_bind(struct device *
- goto err_put_i2c;
- }
-
-+ /* This is the rate that is set by the firmware. The number
-+ * needs to be a bit higher than the pixel clock rate
-+ * (generally 148.5Mhz).
-+ */
-+ ret = clk_set_rate(hdmi->hsm_clock, 163682864);
-+ if (ret) {
-+ DRM_ERROR("Failed to set HSM clock rate: %d\n", ret);
-+ goto err_unprepare_pix;
-+ }
-+
- ret = clk_prepare_enable(hdmi->hsm_clock);
- if (ret) {
- DRM_ERROR("Failed to turn on HDMI state machine clock: %d\n",
-@@ -518,7 +528,24 @@ static int vc4_hdmi_bind(struct device *
- vc4->hdmi = hdmi;
-
- /* HDMI core must be enabled. */
-- WARN_ON_ONCE((HD_READ(VC4_HD_M_CTL) & VC4_HD_M_ENABLE) == 0);
-+ if (!(HD_READ(VC4_HD_M_CTL) & VC4_HD_M_ENABLE)) {
-+ HD_WRITE(VC4_HD_M_CTL, VC4_HD_M_SW_RST);
-+ udelay(1);
-+ HD_WRITE(VC4_HD_M_CTL, 0);
-+
-+ HD_WRITE(VC4_HD_M_CTL, VC4_HD_M_ENABLE);
-+
-+ HDMI_WRITE(VC4_HDMI_SW_RESET_CONTROL,
-+ VC4_HDMI_SW_RESET_HDMI |
-+ VC4_HDMI_SW_RESET_FORMAT_DETECT);
-+
-+ HDMI_WRITE(VC4_HDMI_SW_RESET_CONTROL, 0);
-+
-+ /* PHY should be in reset, like
-+ * vc4_hdmi_encoder_disable() does.
-+ */
-+ HDMI_WRITE(VC4_HDMI_TX_PHY_RESET_CTL, 0xf << 16);
-+ }
-
- drm_encoder_init(drm, hdmi->encoder, &vc4_hdmi_encoder_funcs,
- DRM_MODE_ENCODER_TMDS);
---- a/drivers/gpu/drm/vc4/vc4_regs.h
-+++ b/drivers/gpu/drm/vc4/vc4_regs.h
-@@ -456,6 +456,8 @@
- #define VC4_HDMI_TX_PHY_RESET_CTL 0x2c0
-
- #define VC4_HD_M_CTL 0x00c
-+# define VC4_HD_M_REGISTER_FILE_STANDBY (3 << 6)
-+# define VC4_HD_M_RAM_STANDBY (3 << 4)
- # define VC4_HD_M_SW_RST BIT(2)
- # define VC4_HD_M_ENABLE BIT(0)
-
diff --git a/target/linux/brcm2708/patches-4.4/0286-drm-vc4-Add-another-reg-to-HDMI-debug-dumping.patch b/target/linux/brcm2708/patches-4.4/0286-drm-vc4-Add-another-reg-to-HDMI-debug-dumping.patch
deleted file mode 100644
index 3df4e97..0000000
--- a/target/linux/brcm2708/patches-4.4/0286-drm-vc4-Add-another-reg-to-HDMI-debug-dumping.patch
+++ /dev/null
@@ -1,24 +0,0 @@
-From f3a8e8eeab6e0f183849dded055829f530e8eeb9 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 12 Feb 2016 15:16:56 -0800
-Subject: [PATCH] drm/vc4: Add another reg to HDMI debug dumping.
-
-This is also involved in the HDMI setup sequence so it's nice to see
-it.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 936f1a53f32148cc6164fad7c9a26ebf144e5ffb)
----
- drivers/gpu/drm/vc4/vc4_hdmi.c | 1 +
- 1 file changed, 1 insertion(+)
-
---- a/drivers/gpu/drm/vc4/vc4_hdmi.c
-+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
-@@ -95,6 +95,7 @@ static const struct {
- HDMI_REG(VC4_HDMI_SW_RESET_CONTROL),
- HDMI_REG(VC4_HDMI_HOTPLUG_INT),
- HDMI_REG(VC4_HDMI_HOTPLUG),
-+ HDMI_REG(VC4_HDMI_RAM_PACKET_CONFIG),
- HDMI_REG(VC4_HDMI_HORZA),
- HDMI_REG(VC4_HDMI_HORZB),
- HDMI_REG(VC4_HDMI_FIFO_CTL),
diff --git a/target/linux/brcm2708/patches-4.4/0287-drm-vc4-Fix-the-name-of-the-VSYNCD_EVEN-register.patch b/target/linux/brcm2708/patches-4.4/0287-drm-vc4-Fix-the-name-of-the-VSYNCD_EVEN-register.patch
deleted file mode 100644
index 7cadcbd..0000000
--- a/target/linux/brcm2708/patches-4.4/0287-drm-vc4-Fix-the-name-of-the-VSYNCD_EVEN-register.patch
+++ /dev/null
@@ -1,36 +0,0 @@
-From 1fd348be7113d72334ff198d6f92019839c43e82 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 15 Feb 2016 17:06:02 -0800
-Subject: [PATCH] drm/vc4: Fix the name of the VSYNCD_EVEN register.
-
-It's used for delaying vsync in interlaced mode.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit c31806fbdda910d337b60896040afa708bdfa2bd)
----
- drivers/gpu/drm/vc4/vc4_crtc.c | 2 +-
- drivers/gpu/drm/vc4/vc4_regs.h | 2 +-
- 2 files changed, 2 insertions(+), 2 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_crtc.c
-+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
-@@ -88,7 +88,7 @@ static const struct {
- } crtc_regs[] = {
- CRTC_REG(PV_CONTROL),
- CRTC_REG(PV_V_CONTROL),
-- CRTC_REG(PV_VSYNCD),
-+ CRTC_REG(PV_VSYNCD_EVEN),
- CRTC_REG(PV_HORZA),
- CRTC_REG(PV_HORZB),
- CRTC_REG(PV_VERTA),
---- a/drivers/gpu/drm/vc4/vc4_regs.h
-+++ b/drivers/gpu/drm/vc4/vc4_regs.h
-@@ -187,7 +187,7 @@
- # define PV_VCONTROL_CONTINUOUS BIT(1)
- # define PV_VCONTROL_VIDEN BIT(0)
-
--#define PV_VSYNCD 0x08
-+#define PV_VSYNCD_EVEN 0x08
-
- #define PV_HORZA 0x0c
- # define PV_HORZA_HBP_MASK VC4_MASK(31, 16)
diff --git a/target/linux/brcm2708/patches-4.4/0288-drm-vc4-Fix-setting-of-vertical-timings-in-the-CRTC.patch b/target/linux/brcm2708/patches-4.4/0288-drm-vc4-Fix-setting-of-vertical-timings-in-the-CRTC.patch
deleted file mode 100644
index a21f9c9..0000000
--- a/target/linux/brcm2708/patches-4.4/0288-drm-vc4-Fix-setting-of-vertical-timings-in-the-CRTC.patch
+++ /dev/null
@@ -1,34 +0,0 @@
-From 85937f77d4cbafeba80594c3f760bed4ef114946 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 15 Feb 2016 17:31:41 -0800
-Subject: [PATCH] drm/vc4: Fix setting of vertical timings in the CRTC.
-
-It looks like when I went to add the interlaced bits, I just took the
-existing PV_VERT* block and indented it, instead of copy and pasting
-it first. Without this, changing resolution never worked.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit a7c5047d1ce178dd2b1fa577fc8909ad663d56d5)
----
- drivers/gpu/drm/vc4/vc4_crtc.c | 10 ++++++++++
- 1 file changed, 10 insertions(+)
-
---- a/drivers/gpu/drm/vc4/vc4_crtc.c
-+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
-@@ -217,6 +217,16 @@ static void vc4_crtc_mode_set_nofb(struc
- PV_HORZB_HFP) |
- VC4_SET_FIELD(mode->hdisplay, PV_HORZB_HACTIVE));
-
-+ CRTC_WRITE(PV_VERTA,
-+ VC4_SET_FIELD(mode->vtotal - mode->vsync_end,
-+ PV_VERTA_VBP) |
-+ VC4_SET_FIELD(mode->vsync_end - mode->vsync_start,
-+ PV_VERTA_VSYNC));
-+ CRTC_WRITE(PV_VERTB,
-+ VC4_SET_FIELD(mode->vsync_start - mode->vdisplay,
-+ PV_VERTB_VFP) |
-+ VC4_SET_FIELD(vactive, PV_VERTB_VACTIVE));
-+
- if (interlace) {
- CRTC_WRITE(PV_VERTA_EVEN,
- VC4_SET_FIELD(mode->vtotal - mode->vsync_end - 1,
diff --git a/target/linux/brcm2708/patches-4.4/0289-drm-vc4-Initialize-scaler-DISPBKGND-on-modeset.patch b/target/linux/brcm2708/patches-4.4/0289-drm-vc4-Initialize-scaler-DISPBKGND-on-modeset.patch
deleted file mode 100644
index 5581625..0000000
--- a/target/linux/brcm2708/patches-4.4/0289-drm-vc4-Initialize-scaler-DISPBKGND-on-modeset.patch
+++ /dev/null
@@ -1,68 +0,0 @@
-From 8d1911da16e80f415a42bbaa5b0479ede582b02d Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 16 Feb 2016 10:24:08 -0800
-Subject: [PATCH] drm/vc4: Initialize scaler DISPBKGND on modeset.
-
-We weren't updating the interlaced bit, so we'd scan out incorrectly
-if the firmware had brought up the TV encoder and we were switching to
-HDMI.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 6a609209865247cc748e90158c99f374f79b494c)
----
- drivers/gpu/drm/vc4/vc4_crtc.c | 6 ++++++
- drivers/gpu/drm/vc4/vc4_regs.h | 14 ++++++++++++++
- 2 files changed, 20 insertions(+)
-
---- a/drivers/gpu/drm/vc4/vc4_crtc.c
-+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
-@@ -188,6 +188,8 @@ static int vc4_get_clock_select(struct d
-
- static void vc4_crtc_mode_set_nofb(struct drm_crtc *crtc)
- {
-+ struct drm_device *dev = crtc->dev;
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
- struct drm_crtc_state *state = crtc->state;
- struct drm_display_mode *mode = &state->adjusted_mode;
-@@ -256,6 +258,10 @@ static void vc4_crtc_mode_set_nofb(struc
- PV_CONTROL_FIFO_CLR |
- PV_CONTROL_EN);
-
-+ HVS_WRITE(SCALER_DISPBKGNDX(vc4_crtc->channel),
-+ SCALER_DISPBKGND_AUTOHS |
-+ (interlace ? SCALER_DISPBKGND_INTERLACE : 0));
-+
- if (debug_dump_regs) {
- DRM_INFO("CRTC %d regs after:\n", drm_crtc_index(crtc));
- vc4_crtc_dump_regs(vc4_crtc);
---- a/drivers/gpu/drm/vc4/vc4_regs.h
-+++ b/drivers/gpu/drm/vc4/vc4_regs.h
-@@ -350,6 +350,17 @@
- # define SCALER_DISPCTRLX_HEIGHT_SHIFT 0
-
- #define SCALER_DISPBKGND0 0x00000044
-+# define SCALER_DISPBKGND_AUTOHS BIT(31)
-+# define SCALER_DISPBKGND_INTERLACE BIT(30)
-+# define SCALER_DISPBKGND_GAMMA BIT(29)
-+# define SCALER_DISPBKGND_TESTMODE_MASK VC4_MASK(28, 25)
-+# define SCALER_DISPBKGND_TESTMODE_SHIFT 25
-+/* Enables filling the scaler line with the RGB value in the low 24
-+ * bits before compositing. Costs cycles, so should be skipped if
-+ * opaque display planes will cover everything.
-+ */
-+# define SCALER_DISPBKGND_FILL BIT(24)
-+
- #define SCALER_DISPSTAT0 0x00000048
- #define SCALER_DISPBASE0 0x0000004c
- # define SCALER_DISPSTATX_MODE_MASK VC4_MASK(31, 30)
-@@ -362,6 +373,9 @@
- # define SCALER_DISPSTATX_EMPTY BIT(28)
- #define SCALER_DISPCTRL1 0x00000050
- #define SCALER_DISPBKGND1 0x00000054
-+#define SCALER_DISPBKGNDX(x) (SCALER_DISPBKGND0 + \
-+ (x) * (SCALER_DISPBKGND1 - \
-+ SCALER_DISPBKGND0))
- #define SCALER_DISPSTAT1 0x00000058
- #define SCALER_DISPSTATX(x) (SCALER_DISPSTAT0 + \
- (x) * (SCALER_DISPSTAT1 - \
diff --git a/target/linux/brcm2708/patches-4.4/0290-drm-vc4-improve-throughput-by-pipelining-binning-and.patch b/target/linux/brcm2708/patches-4.4/0290-drm-vc4-improve-throughput-by-pipelining-binning-and.patch
deleted file mode 100644
index addef40..0000000
--- a/target/linux/brcm2708/patches-4.4/0290-drm-vc4-improve-throughput-by-pipelining-binning-and.patch
+++ /dev/null
@@ -1,429 +0,0 @@
-From c661b60a4057da2d212fc5e8e2a56d463d912974 Mon Sep 17 00:00:00 2001
-From: Varad Gautam <varadgautam at gmail.com>
-Date: Wed, 17 Feb 2016 19:08:21 +0530
-Subject: [PATCH] drm/vc4: improve throughput by pipelining binning and
- rendering jobs
-
-The hardware provides us with separate threads for binning and
-rendering, and the existing model waits for them both to complete
-before submitting the next job.
-
-Splitting the binning and rendering submissions reduces idle time and
-gives us approx 20-30% speedup with some x11perf tests such as -line10
-and -tilerect1. Improves openarena performance by 1.01897% +/-
-0.247857% (n=16).
-
-Thanks to anholt for suggesting this.
-
-v2: Rebase on the spurious resets fix (change by anholt).
-
-Signed-off-by: Varad Gautam <varadgautam at gmail.com>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit ca26d28bbaa39f31d5e7e4812603b015c8d54207)
----
- drivers/gpu/drm/vc4/vc4_drv.h | 37 +++++++++----
- drivers/gpu/drm/vc4/vc4_gem.c | 123 ++++++++++++++++++++++++++++++------------
- drivers/gpu/drm/vc4/vc4_irq.c | 58 ++++++++++++++++----
- 3 files changed, 166 insertions(+), 52 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_drv.h
-+++ b/drivers/gpu/drm/vc4/vc4_drv.h
-@@ -53,7 +53,7 @@ struct vc4_dev {
- /* Protects bo_cache and the BO stats. */
- struct mutex bo_lock;
-
-- /* Sequence number for the last job queued in job_list.
-+ /* Sequence number for the last job queued in bin_job_list.
- * Starts at 0 (no jobs emitted).
- */
- uint64_t emit_seqno;
-@@ -63,11 +63,19 @@ struct vc4_dev {
- */
- uint64_t finished_seqno;
-
-- /* List of all struct vc4_exec_info for jobs to be executed.
-- * The first job in the list is the one currently programmed
-- * into ct0ca/ct1ca for execution.
-+ /* List of all struct vc4_exec_info for jobs to be executed in
-+ * the binner. The first job in the list is the one currently
-+ * programmed into ct0ca for execution.
-+ */
-+ struct list_head bin_job_list;
-+
-+ /* List of all struct vc4_exec_info for jobs that have
-+ * completed binning and are ready for rendering. The first
-+ * job in the list is the one currently programmed into ct1ca
-+ * for execution.
- */
-- struct list_head job_list;
-+ struct list_head render_job_list;
-+
- /* List of the finished vc4_exec_infos waiting to be freed by
- * job_done_work.
- */
-@@ -291,11 +299,20 @@ struct vc4_exec_info {
- };
-
- static inline struct vc4_exec_info *
--vc4_first_job(struct vc4_dev *vc4)
-+vc4_first_bin_job(struct vc4_dev *vc4)
-+{
-+ if (list_empty(&vc4->bin_job_list))
-+ return NULL;
-+ return list_first_entry(&vc4->bin_job_list, struct vc4_exec_info, head);
-+}
-+
-+static inline struct vc4_exec_info *
-+vc4_first_render_job(struct vc4_dev *vc4)
- {
-- if (list_empty(&vc4->job_list))
-+ if (list_empty(&vc4->render_job_list))
- return NULL;
-- return list_first_entry(&vc4->job_list, struct vc4_exec_info, head);
-+ return list_first_entry(&vc4->render_job_list,
-+ struct vc4_exec_info, head);
- }
-
- /**
-@@ -410,7 +427,9 @@ int vc4_wait_seqno_ioctl(struct drm_devi
- struct drm_file *file_priv);
- int vc4_wait_bo_ioctl(struct drm_device *dev, void *data,
- struct drm_file *file_priv);
--void vc4_submit_next_job(struct drm_device *dev);
-+void vc4_submit_next_bin_job(struct drm_device *dev);
-+void vc4_submit_next_render_job(struct drm_device *dev);
-+void vc4_move_job_to_render(struct drm_device *dev, struct vc4_exec_info *exec);
- int vc4_wait_for_seqno(struct drm_device *dev, uint64_t seqno,
- uint64_t timeout_ns, bool interruptible);
- void vc4_job_handle_completed(struct vc4_dev *vc4);
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -154,10 +154,10 @@ vc4_save_hang_state(struct drm_device *d
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct drm_vc4_get_hang_state *state;
- struct vc4_hang_state *kernel_state;
-- struct vc4_exec_info *exec;
-+ struct vc4_exec_info *exec[2];
- struct vc4_bo *bo;
- unsigned long irqflags;
-- unsigned int i, unref_list_count;
-+ unsigned int i, j, unref_list_count, prev_idx;
-
- kernel_state = kcalloc(1, sizeof(*kernel_state), GFP_KERNEL);
- if (!kernel_state)
-@@ -166,37 +166,55 @@ vc4_save_hang_state(struct drm_device *d
- state = &kernel_state->user_state;
-
- spin_lock_irqsave(&vc4->job_lock, irqflags);
-- exec = vc4_first_job(vc4);
-- if (!exec) {
-+ exec[0] = vc4_first_bin_job(vc4);
-+ exec[1] = vc4_first_render_job(vc4);
-+ if (!exec[0] && !exec[1]) {
- spin_unlock_irqrestore(&vc4->job_lock, irqflags);
- return;
- }
-
-- unref_list_count = 0;
-- list_for_each_entry(bo, &exec->unref_list, unref_head)
-- unref_list_count++;
--
-- state->bo_count = exec->bo_count + unref_list_count;
-- kernel_state->bo = kcalloc(state->bo_count, sizeof(*kernel_state->bo),
-- GFP_ATOMIC);
-+ /* Get the bos from both binner and renderer into hang state. */
-+ state->bo_count = 0;
-+ for (i = 0; i < 2; i++) {
-+ if (!exec[i])
-+ continue;
-+
-+ unref_list_count = 0;
-+ list_for_each_entry(bo, &exec[i]->unref_list, unref_head)
-+ unref_list_count++;
-+ state->bo_count += exec[i]->bo_count + unref_list_count;
-+ }
-+
-+ kernel_state->bo = kcalloc(state->bo_count,
-+ sizeof(*kernel_state->bo), GFP_ATOMIC);
-+
- if (!kernel_state->bo) {
- spin_unlock_irqrestore(&vc4->job_lock, irqflags);
- return;
- }
-
-- for (i = 0; i < exec->bo_count; i++) {
-- drm_gem_object_reference(&exec->bo[i]->base);
-- kernel_state->bo[i] = &exec->bo[i]->base;
-- }
-+ prev_idx = 0;
-+ for (i = 0; i < 2; i++) {
-+ if (!exec[i])
-+ continue;
-+
-+ for (j = 0; j < exec[i]->bo_count; j++) {
-+ drm_gem_object_reference(&exec[i]->bo[j]->base);
-+ kernel_state->bo[j + prev_idx] = &exec[i]->bo[j]->base;
-+ }
-
-- list_for_each_entry(bo, &exec->unref_list, unref_head) {
-- drm_gem_object_reference(&bo->base.base);
-- kernel_state->bo[i] = &bo->base.base;
-- i++;
-+ list_for_each_entry(bo, &exec[i]->unref_list, unref_head) {
-+ drm_gem_object_reference(&bo->base.base);
-+ kernel_state->bo[j + prev_idx] = &bo->base.base;
-+ j++;
-+ }
-+ prev_idx = j + 1;
- }
-
-- state->start_bin = exec->ct0ca;
-- state->start_render = exec->ct1ca;
-+ if (exec[0])
-+ state->start_bin = exec[0]->ct0ca;
-+ if (exec[1])
-+ state->start_render = exec[1]->ct1ca;
-
- spin_unlock_irqrestore(&vc4->job_lock, irqflags);
-
-@@ -272,13 +290,15 @@ vc4_hangcheck_elapsed(unsigned long data
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- uint32_t ct0ca, ct1ca;
- unsigned long irqflags;
-- struct vc4_exec_info *exec;
-+ struct vc4_exec_info *bin_exec, *render_exec;
-
- spin_lock_irqsave(&vc4->job_lock, irqflags);
-- exec = vc4_first_job(vc4);
-+
-+ bin_exec = vc4_first_bin_job(vc4);
-+ render_exec = vc4_first_render_job(vc4);
-
- /* If idle, we can stop watching for hangs. */
-- if (!exec) {
-+ if (!bin_exec && !render_exec) {
- spin_unlock_irqrestore(&vc4->job_lock, irqflags);
- return;
- }
-@@ -289,9 +309,12 @@ vc4_hangcheck_elapsed(unsigned long data
- /* If we've made any progress in execution, rearm the timer
- * and wait.
- */
-- if (ct0ca != exec->last_ct0ca || ct1ca != exec->last_ct1ca) {
-- exec->last_ct0ca = ct0ca;
-- exec->last_ct1ca = ct1ca;
-+ if ((bin_exec && ct0ca != bin_exec->last_ct0ca) ||
-+ (render_exec && ct1ca != render_exec->last_ct1ca)) {
-+ if (bin_exec)
-+ bin_exec->last_ct0ca = ct0ca;
-+ if (render_exec)
-+ render_exec->last_ct1ca = ct1ca;
- spin_unlock_irqrestore(&vc4->job_lock, irqflags);
- vc4_queue_hangcheck(dev);
- return;
-@@ -391,11 +414,13 @@ vc4_flush_caches(struct drm_device *dev)
- * The job_lock should be held during this.
- */
- void
--vc4_submit_next_job(struct drm_device *dev)
-+vc4_submit_next_bin_job(struct drm_device *dev)
- {
- struct vc4_dev *vc4 = to_vc4_dev(dev);
-- struct vc4_exec_info *exec = vc4_first_job(vc4);
-+ struct vc4_exec_info *exec;
-
-+again:
-+ exec = vc4_first_bin_job(vc4);
- if (!exec)
- return;
-
-@@ -405,11 +430,40 @@ vc4_submit_next_job(struct drm_device *d
- V3D_WRITE(V3D_BPOA, 0);
- V3D_WRITE(V3D_BPOS, 0);
-
-- if (exec->ct0ca != exec->ct0ea)
-+ /* Either put the job in the binner if it uses the binner, or
-+ * immediately move it to the to-be-rendered queue.
-+ */
-+ if (exec->ct0ca != exec->ct0ea) {
- submit_cl(dev, 0, exec->ct0ca, exec->ct0ea);
-+ } else {
-+ vc4_move_job_to_render(dev, exec);
-+ goto again;
-+ }
-+}
-+
-+void
-+vc4_submit_next_render_job(struct drm_device *dev)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ struct vc4_exec_info *exec = vc4_first_render_job(vc4);
-+
-+ if (!exec)
-+ return;
-+
- submit_cl(dev, 1, exec->ct1ca, exec->ct1ea);
- }
-
-+void
-+vc4_move_job_to_render(struct drm_device *dev, struct vc4_exec_info *exec)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ bool was_empty = list_empty(&vc4->render_job_list);
-+
-+ list_move_tail(&exec->head, &vc4->render_job_list);
-+ if (was_empty)
-+ vc4_submit_next_render_job(dev);
-+}
-+
- static void
- vc4_update_bo_seqnos(struct vc4_exec_info *exec, uint64_t seqno)
- {
-@@ -448,14 +502,14 @@ vc4_queue_submit(struct drm_device *dev,
- exec->seqno = seqno;
- vc4_update_bo_seqnos(exec, seqno);
-
-- list_add_tail(&exec->head, &vc4->job_list);
-+ list_add_tail(&exec->head, &vc4->bin_job_list);
-
- /* If no job was executing, kick ours off. Otherwise, it'll
-- * get started when the previous job's frame done interrupt
-+ * get started when the previous job's flush done interrupt
- * occurs.
- */
-- if (vc4_first_job(vc4) == exec) {
-- vc4_submit_next_job(dev);
-+ if (vc4_first_bin_job(vc4) == exec) {
-+ vc4_submit_next_bin_job(dev);
- vc4_queue_hangcheck(dev);
- }
-
-@@ -849,7 +903,8 @@ vc4_gem_init(struct drm_device *dev)
- {
- struct vc4_dev *vc4 = to_vc4_dev(dev);
-
-- INIT_LIST_HEAD(&vc4->job_list);
-+ INIT_LIST_HEAD(&vc4->bin_job_list);
-+ INIT_LIST_HEAD(&vc4->render_job_list);
- INIT_LIST_HEAD(&vc4->job_done_list);
- INIT_LIST_HEAD(&vc4->seqno_cb_list);
- spin_lock_init(&vc4->job_lock);
---- a/drivers/gpu/drm/vc4/vc4_irq.c
-+++ b/drivers/gpu/drm/vc4/vc4_irq.c
-@@ -30,6 +30,10 @@
- * disables that specific interrupt, and 0s written are ignored
- * (reading either one returns the set of enabled interrupts).
- *
-+ * When we take a binning flush done interrupt, we need to submit the
-+ * next frame for binning and move the finished frame to the render
-+ * thread.
-+ *
- * When we take a render frame interrupt, we need to wake the
- * processes waiting for some frame to be done, and get the next frame
- * submitted ASAP (so the hardware doesn't sit idle when there's work
-@@ -44,6 +48,7 @@
- #include "vc4_regs.h"
-
- #define V3D_DRIVER_IRQS (V3D_INT_OUTOMEM | \
-+ V3D_INT_FLDONE | \
- V3D_INT_FRDONE)
-
- DECLARE_WAIT_QUEUE_HEAD(render_wait);
-@@ -77,7 +82,7 @@ vc4_overflow_mem_work(struct work_struct
- unsigned long irqflags;
-
- spin_lock_irqsave(&vc4->job_lock, irqflags);
-- current_exec = vc4_first_job(vc4);
-+ current_exec = vc4_first_bin_job(vc4);
- if (current_exec) {
- vc4->overflow_mem->seqno = vc4->finished_seqno + 1;
- list_add_tail(&vc4->overflow_mem->unref_head,
-@@ -98,17 +103,43 @@ vc4_overflow_mem_work(struct work_struct
- }
-
- static void
--vc4_irq_finish_job(struct drm_device *dev)
-+vc4_irq_finish_bin_job(struct drm_device *dev)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ struct vc4_exec_info *exec = vc4_first_bin_job(vc4);
-+
-+ if (!exec)
-+ return;
-+
-+ vc4_move_job_to_render(dev, exec);
-+ vc4_submit_next_bin_job(dev);
-+}
-+
-+static void
-+vc4_cancel_bin_job(struct drm_device *dev)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ struct vc4_exec_info *exec = vc4_first_bin_job(vc4);
-+
-+ if (!exec)
-+ return;
-+
-+ list_move_tail(&exec->head, &vc4->bin_job_list);
-+ vc4_submit_next_bin_job(dev);
-+}
-+
-+static void
-+vc4_irq_finish_render_job(struct drm_device *dev)
- {
- struct vc4_dev *vc4 = to_vc4_dev(dev);
-- struct vc4_exec_info *exec = vc4_first_job(vc4);
-+ struct vc4_exec_info *exec = vc4_first_render_job(vc4);
-
- if (!exec)
- return;
-
- vc4->finished_seqno++;
- list_move_tail(&exec->head, &vc4->job_done_list);
-- vc4_submit_next_job(dev);
-+ vc4_submit_next_render_job(dev);
-
- wake_up_all(&vc4->job_wait_queue);
- schedule_work(&vc4->job_done_work);
-@@ -125,9 +156,10 @@ vc4_irq(int irq, void *arg)
- barrier();
- intctl = V3D_READ(V3D_INTCTL);
-
-- /* Acknowledge the interrupts we're handling here. The render
-- * frame done interrupt will be cleared, while OUTOMEM will
-- * stay high until the underlying cause is cleared.
-+ /* Acknowledge the interrupts we're handling here. The binner
-+ * last flush / render frame done interrupt will be cleared,
-+ * while OUTOMEM will stay high until the underlying cause is
-+ * cleared.
- */
- V3D_WRITE(V3D_INTCTL, intctl);
-
-@@ -138,9 +170,16 @@ vc4_irq(int irq, void *arg)
- status = IRQ_HANDLED;
- }
-
-+ if (intctl & V3D_INT_FLDONE) {
-+ spin_lock(&vc4->job_lock);
-+ vc4_irq_finish_bin_job(dev);
-+ spin_unlock(&vc4->job_lock);
-+ status = IRQ_HANDLED;
-+ }
-+
- if (intctl & V3D_INT_FRDONE) {
- spin_lock(&vc4->job_lock);
-- vc4_irq_finish_job(dev);
-+ vc4_irq_finish_render_job(dev);
- spin_unlock(&vc4->job_lock);
- status = IRQ_HANDLED;
- }
-@@ -205,6 +244,7 @@ void vc4_irq_reset(struct drm_device *de
- V3D_WRITE(V3D_INTENA, V3D_DRIVER_IRQS);
-
- spin_lock_irqsave(&vc4->job_lock, irqflags);
-- vc4_irq_finish_job(dev);
-+ vc4_cancel_bin_job(dev);
-+ vc4_irq_finish_render_job(dev);
- spin_unlock_irqrestore(&vc4->job_lock, irqflags);
- }
diff --git a/target/linux/brcm2708/patches-4.4/0291-drm-vc4-Let-gpiolib-know-that-we-re-OK-with-sleeping.patch b/target/linux/brcm2708/patches-4.4/0291-drm-vc4-Let-gpiolib-know-that-we-re-OK-with-sleeping.patch
deleted file mode 100644
index e75c0fb..0000000
--- a/target/linux/brcm2708/patches-4.4/0291-drm-vc4-Let-gpiolib-know-that-we-re-OK-with-sleeping.patch
+++ /dev/null
@@ -1,27 +0,0 @@
-From aa917f1fec96141a6e3fe05eb6d4338ffd33d4d1 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 29 Feb 2016 17:53:00 -0800
-Subject: [PATCH] drm/vc4: Let gpiolib know that we're OK with sleeping for
- HPD.
-
-Fixes an error thrown every few seconds when we poll HPD when it's on
-a I2C to GPIO expander.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Tested-by: Daniel Stone <daniels at collabora.com>
-(cherry picked from commit 0e60eab57557bc06bb3a5ef8d5d6dcd9ddd47aff)
----
- drivers/gpu/drm/vc4/vc4_hdmi.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/gpu/drm/vc4/vc4_hdmi.c
-+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
-@@ -168,7 +168,7 @@ vc4_hdmi_connector_detect(struct drm_con
- return connector_status_connected;
-
- if (vc4->hdmi->hpd_gpio) {
-- if (gpio_get_value(vc4->hdmi->hpd_gpio))
-+ if (gpio_get_value_cansleep(vc4->hdmi->hpd_gpio))
- return connector_status_connected;
- else
- return connector_status_disconnected;
diff --git a/target/linux/brcm2708/patches-4.4/0292-drm-vc4-Respect-GPIO_ACTIVE_LOW-on-HDMI-HPD-if-set-i.patch b/target/linux/brcm2708/patches-4.4/0292-drm-vc4-Respect-GPIO_ACTIVE_LOW-on-HDMI-HPD-if-set-i.patch
deleted file mode 100644
index 1922777..0000000
--- a/target/linux/brcm2708/patches-4.4/0292-drm-vc4-Respect-GPIO_ACTIVE_LOW-on-HDMI-HPD-if-set-i.patch
+++ /dev/null
@@ -1,57 +0,0 @@
-From 79c0037706c4e589f1743679e21a0aee51b9b609 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 29 Feb 2016 17:53:01 -0800
-Subject: [PATCH] drm/vc4: Respect GPIO_ACTIVE_LOW on HDMI HPD if set in the
- devicetree.
-
-The original Raspberry Pi had the GPIO active high, but the later
-models are active low. The DT GPIO bindings allow specifying the
-active flag, except that it doesn't get propagated to the gpiodesc, so
-you have to handle it yourself.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Tested-by: Daniel Stone <daniels at collabora.com>
-(cherry picked from commit 0b06e0a7945130e6a187f7959529cba7725f573a)
----
- drivers/gpu/drm/vc4/vc4_hdmi.c | 12 ++++++++++--
- 1 file changed, 10 insertions(+), 2 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_hdmi.c
-+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
-@@ -47,6 +47,7 @@ struct vc4_hdmi {
- void __iomem *hdmicore_regs;
- void __iomem *hd_regs;
- int hpd_gpio;
-+ bool hpd_active_low;
-
- struct clk *pixel_clock;
- struct clk *hsm_clock;
-@@ -168,7 +169,8 @@ vc4_hdmi_connector_detect(struct drm_con
- return connector_status_connected;
-
- if (vc4->hdmi->hpd_gpio) {
-- if (gpio_get_value_cansleep(vc4->hdmi->hpd_gpio))
-+ if (gpio_get_value_cansleep(vc4->hdmi->hpd_gpio) ^
-+ vc4->hdmi->hpd_active_low)
- return connector_status_connected;
- else
- return connector_status_disconnected;
-@@ -519,11 +521,17 @@ static int vc4_hdmi_bind(struct device *
- * we'll use the HDMI core's register.
- */
- if (of_find_property(dev->of_node, "hpd-gpios", &value)) {
-- hdmi->hpd_gpio = of_get_named_gpio(dev->of_node, "hpd-gpios", 0);
-+ enum of_gpio_flags hpd_gpio_flags;
-+
-+ hdmi->hpd_gpio = of_get_named_gpio_flags(dev->of_node,
-+ "hpd-gpios", 0,
-+ &hpd_gpio_flags);
- if (hdmi->hpd_gpio < 0) {
- ret = hdmi->hpd_gpio;
- goto err_unprepare_hsm;
- }
-+
-+ hdmi->hpd_active_low = hpd_gpio_flags & OF_GPIO_ACTIVE_LOW;
- }
-
- vc4->hdmi = hdmi;
diff --git a/target/linux/brcm2708/patches-4.4/0293-drm-vc4-Return-EFAULT-on-copy_from_user-failure.patch b/target/linux/brcm2708/patches-4.4/0293-drm-vc4-Return-EFAULT-on-copy_from_user-failure.patch
deleted file mode 100644
index 33c695f..0000000
--- a/target/linux/brcm2708/patches-4.4/0293-drm-vc4-Return-EFAULT-on-copy_from_user-failure.patch
+++ /dev/null
@@ -1,36 +0,0 @@
-From 99163bd65fc65f2a3f754de89a7009d4b243bbdc Mon Sep 17 00:00:00 2001
-From: Dan Carpenter <dan.carpenter at oracle.com>
-Date: Tue, 8 Mar 2016 15:09:41 +0300
-Subject: [PATCH] drm/vc4: Return -EFAULT on copy_from_user() failure
-
-The copy_from_user() function returns the number of bytes not copied but
-we want to return a negative error code.
-
-Fixes: 463873d57014 ('drm/vc4: Add an API for creating GPU shaders in GEM BOs.')
-Cc: stable at vger.kernel.org
-Signed-off-by: Dan Carpenter <dan.carpenter at oracle.com>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 585cb132a48190b554aecda2ebc3e2911fcbb665)
----
- drivers/gpu/drm/vc4/vc4_bo.c | 7 ++++---
- 1 file changed, 4 insertions(+), 3 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_bo.c
-+++ b/drivers/gpu/drm/vc4/vc4_bo.c
-@@ -519,11 +519,12 @@ vc4_create_shader_bo_ioctl(struct drm_de
- if (IS_ERR(bo))
- return PTR_ERR(bo);
-
-- ret = copy_from_user(bo->base.vaddr,
-+ if (copy_from_user(bo->base.vaddr,
- (void __user *)(uintptr_t)args->data,
-- args->size);
-- if (ret != 0)
-+ args->size)) {
-+ ret = -EFAULT;
- goto fail;
-+ }
- /* Clear the rest of the memory from allocating from the BO
- * cache.
- */
diff --git a/target/linux/brcm2708/patches-4.4/0294-drm-vc4-Recognize-a-more-specific-compatible-string-.patch b/target/linux/brcm2708/patches-4.4/0294-drm-vc4-Recognize-a-more-specific-compatible-string-.patch
deleted file mode 100644
index 3eb9735..0000000
--- a/target/linux/brcm2708/patches-4.4/0294-drm-vc4-Recognize-a-more-specific-compatible-string-.patch
+++ /dev/null
@@ -1,28 +0,0 @@
-From 6bffd5f15e00a2ccc721995d7e924447b6a9deb0 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 4 Mar 2016 12:32:07 -0800
-Subject: [PATCH] drm/vc4: Recognize a more specific compatible string for V3D.
-
-The Raspberry Pi Foundation's firmware updates are shipping device
-trees using the old string, so we'll keep recognizing that as this rev
-of V3D. Still, we should use a more specific name in the upstream DT
-to clarify which board is being supported, in case we do other revs of
-V3D in the future.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Acked-by: Stephen Warren <swarren at wwwdotorg.org>
-(cherry picked from commit 90d7116061f86c1f8ea460806a0414addea7b58b)
----
- drivers/gpu/drm/vc4/vc4_v3d.c | 1 +
- 1 file changed, 1 insertion(+)
-
---- a/drivers/gpu/drm/vc4/vc4_v3d.c
-+++ b/drivers/gpu/drm/vc4/vc4_v3d.c
-@@ -256,6 +256,7 @@ static int vc4_v3d_dev_remove(struct pla
- }
-
- static const struct of_device_id vc4_v3d_dt_match[] = {
-+ { .compatible = "brcm,bcm2835-v3d" },
- { .compatible = "brcm,vc4-v3d" },
- {}
- };
diff --git a/target/linux/brcm2708/patches-4.4/0295-ARM-bcm2708-Move-the-CMA-range-down-for-kernel-4.4.patch b/target/linux/brcm2708/patches-4.4/0295-ARM-bcm2708-Move-the-CMA-range-down-for-kernel-4.4.patch
deleted file mode 100644
index 9a0adb0..0000000
--- a/target/linux/brcm2708/patches-4.4/0295-ARM-bcm2708-Move-the-CMA-range-down-for-kernel-4.4.patch
+++ /dev/null
@@ -1,24 +0,0 @@
-From 84af80ea19bb7e94e15c9e986594a07befb5930f Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 19 Apr 2016 17:21:06 -0700
-Subject: [PATCH] ARM: bcm2708: Move the CMA range down for kernel 4.4.
-
-The previous area no longer works, for reasons I haven't investigated.
-Just move it somewhere that works.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts
-@@ -91,7 +91,7 @@
- fragment at 4 {
- target-path = "/chosen";
- __overlay__ {
-- bootargs = "cma=256M at 512M";
-+ bootargs = "cma=256M at 256M";
- };
- };
- };
diff --git a/target/linux/brcm2708/patches-4.4/0296-clk-bcm2835-fix-check-of-error-code-returned-by-devm.patch b/target/linux/brcm2708/patches-4.4/0296-clk-bcm2835-fix-check-of-error-code-returned-by-devm.patch
deleted file mode 100644
index b79f290..0000000
--- a/target/linux/brcm2708/patches-4.4/0296-clk-bcm2835-fix-check-of-error-code-returned-by-devm.patch
+++ /dev/null
@@ -1,33 +0,0 @@
-From bd6f91eb03d1f33e0be64c9b3a5a121e32d420f0 Mon Sep 17 00:00:00 2001
-From: Vladimir Zapolskiy <vz at mleia.com>
-Date: Sun, 6 Mar 2016 03:21:35 +0200
-Subject: [PATCH] clk: bcm2835: fix check of error code returned by
- devm_ioremap_resource()
-
-The change fixes potential oops while accessing iomem on invalid
-address, if devm_ioremap_resource() fails due to some reason.
-
-The devm_ioremap_resource() function returns ERR_PTR() and never
-returns NULL, which makes useless a following check for NULL.
-
-Signed-off-by: Vladimir Zapolskiy <vz at mleia.com>
-Fixes: 5e63dcc74b30 ("clk: bcm2835: Add a driver for the auxiliary peripheral clock gates")
-Reviewed-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
----
- drivers/clk/bcm/clk-bcm2835-aux.c | 4 ++--
- 1 file changed, 2 insertions(+), 2 deletions(-)
-
---- a/drivers/clk/bcm/clk-bcm2835-aux.c
-+++ b/drivers/clk/bcm/clk-bcm2835-aux.c
-@@ -38,8 +38,8 @@ static int bcm2835_aux_clk_probe(struct
-
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- reg = devm_ioremap_resource(dev, res);
-- if (!reg)
-- return -ENODEV;
-+ if (IS_ERR(reg))
-+ return PTR_ERR(reg);
-
- onecell = devm_kmalloc(dev, sizeof(*onecell), GFP_KERNEL);
- if (!onecell)
diff --git a/target/linux/brcm2708/patches-4.4/0297-vchiq_arm-Add-completion-records-under-the-mutex.patch b/target/linux/brcm2708/patches-4.4/0297-vchiq_arm-Add-completion-records-under-the-mutex.patch
deleted file mode 100644
index 642b301..0000000
--- a/target/linux/brcm2708/patches-4.4/0297-vchiq_arm-Add-completion-records-under-the-mutex.patch
+++ /dev/null
@@ -1,63 +0,0 @@
-From 210830154ad28d544e79b188217190eb0e06a941 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Thu, 21 Apr 2016 13:49:32 +0100
-Subject: [PATCH] vchiq_arm: Add completion records under the mutex
-
-An issue was observed when flushing openmax components
-which generate a large number of messages returning
-buffers to host.
-
-We occasionally found a duplicate message from 16
-messages prior, resulting in a buffer returned twice.
-
-While only one thread adds completions, without the
-mutex you don't get the protection of the automatic
-memory barrier you get with synchronisation objects.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- drivers/misc/vc04_services/interface/vchiq_arm/vchiq_arm.c | 13 ++++++++++++-
- 1 file changed, 12 insertions(+), 1 deletion(-)
-
---- a/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_arm.c
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_arm.c
-@@ -210,6 +210,8 @@ add_completion(VCHIQ_INSTANCE_T instance
- VCHIQ_COMPLETION_DATA_T *completion;
- DEBUG_INITIALISE(g_state.local)
-
-+ mutex_lock(&instance->completion_mutex);
-+
- while (instance->completion_insert ==
- (instance->completion_remove + MAX_COMPLETIONS)) {
- /* Out of space - wait for the client */
-@@ -217,11 +219,17 @@ add_completion(VCHIQ_INSTANCE_T instance
- vchiq_log_trace(vchiq_arm_log_level,
- "add_completion - completion queue full");
- DEBUG_COUNT(COMPLETION_QUEUE_FULL_COUNT);
-+
-+ mutex_unlock(&instance->completion_mutex);
- if (down_interruptible(&instance->remove_event) != 0) {
- vchiq_log_info(vchiq_arm_log_level,
- "service_callback interrupted");
- return VCHIQ_RETRY;
-- } else if (instance->closing) {
-+ }
-+
-+ mutex_lock(&instance->completion_mutex);
-+ if (instance->closing) {
-+ mutex_unlock(&instance->completion_mutex);
- vchiq_log_info(vchiq_arm_log_level,
- "service_callback closing");
- return VCHIQ_SUCCESS;
-@@ -254,8 +262,11 @@ add_completion(VCHIQ_INSTANCE_T instance
- if (reason == VCHIQ_MESSAGE_AVAILABLE)
- user_service->message_available_pos =
- instance->completion_insert;
-+
- instance->completion_insert++;
-
-+ mutex_unlock(&instance->completion_mutex);
-+
- up(&instance->insert_event);
-
- return VCHIQ_SUCCESS;
diff --git a/target/linux/brcm2708/patches-4.4/0298-config-Add-DRM_UDL-module.patch b/target/linux/brcm2708/patches-4.4/0298-config-Add-DRM_UDL-module.patch
deleted file mode 100644
index 72e5119..0000000
--- a/target/linux/brcm2708/patches-4.4/0298-config-Add-DRM_UDL-module.patch
+++ /dev/null
@@ -1,59 +0,0 @@
-From 00f3e076b530df01f8e05ba86829c2d18072b150 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Thu, 21 Apr 2016 16:07:15 +0100
-Subject: [PATCH] config: Add DRM_UDL module
-
-See: https://github.com/raspberrypi/linux/issues/1422
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/configs/bcm2709_defconfig | 5 +++--
- arch/arm/configs/bcmrpi_defconfig | 5 +++--
- 2 files changed, 6 insertions(+), 4 deletions(-)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -815,6 +815,7 @@ CONFIG_VIDEO_TW9906=m
- CONFIG_VIDEO_OV7640=m
- CONFIG_VIDEO_MT9V011=m
- CONFIG_DRM=m
-+CONFIG_DRM_UDL=m
- CONFIG_DRM_VC4=m
- CONFIG_FB=y
- CONFIG_FB_BCM2708=y
-@@ -854,10 +855,10 @@ CONFIG_SND_BCM2708_SOC_HIFIBERRY_DAC=m
- CONFIG_SND_BCM2708_SOC_HIFIBERRY_DACPLUS=m
- CONFIG_SND_BCM2708_SOC_HIFIBERRY_DIGI=m
- CONFIG_SND_BCM2708_SOC_HIFIBERRY_AMP=m
--CONFIG_SND_BCM2708_SOC_BOOMBERRY_DAC=m
--CONFIG_SND_BCM2708_SOC_BOOMBERRY_DIGI=m
- CONFIG_SND_BCM2708_SOC_RPI_DAC=m
- CONFIG_SND_BCM2708_SOC_RPI_PROTO=m
-+CONFIG_SND_BCM2708_SOC_BOOMBERRY_DAC=m
-+CONFIG_SND_BCM2708_SOC_BOOMBERRY_DIGI=m
- CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC=m
- CONFIG_SND_BCM2708_SOC_RASPIDAC3=m
- CONFIG_SND_SOC_ADAU1701=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -807,6 +807,7 @@ CONFIG_VIDEO_TW9906=m
- CONFIG_VIDEO_OV7640=m
- CONFIG_VIDEO_MT9V011=m
- CONFIG_DRM=m
-+CONFIG_DRM_UDL=m
- CONFIG_DRM_VC4=m
- CONFIG_FB=y
- CONFIG_FB_BCM2708=y
-@@ -846,10 +847,10 @@ CONFIG_SND_BCM2708_SOC_HIFIBERRY_DAC=m
- CONFIG_SND_BCM2708_SOC_HIFIBERRY_DACPLUS=m
- CONFIG_SND_BCM2708_SOC_HIFIBERRY_DIGI=m
- CONFIG_SND_BCM2708_SOC_HIFIBERRY_AMP=m
--CONFIG_SND_BCM2708_SOC_BOOMBERRY_DAC=m
--CONFIG_SND_BCM2708_SOC_BOOMBERRY_DIGI=m
- CONFIG_SND_BCM2708_SOC_RPI_DAC=m
- CONFIG_SND_BCM2708_SOC_RPI_PROTO=m
-+CONFIG_SND_BCM2708_SOC_BOOMBERRY_DAC=m
-+CONFIG_SND_BCM2708_SOC_BOOMBERRY_DIGI=m
- CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC=m
- CONFIG_SND_BCM2708_SOC_RASPIDAC3=m
- CONFIG_SND_SOC_ADAU1701=m
diff --git a/target/linux/brcm2708/patches-4.4/0299-bcm2835-i2s-Reduce-the-TX-DREQ-threshold.patch b/target/linux/brcm2708/patches-4.4/0299-bcm2835-i2s-Reduce-the-TX-DREQ-threshold.patch
deleted file mode 100644
index ca2ba89..0000000
--- a/target/linux/brcm2708/patches-4.4/0299-bcm2835-i2s-Reduce-the-TX-DREQ-threshold.patch
+++ /dev/null
@@ -1,48 +0,0 @@
-From 5178a5d56cff7e0db126a456355a710782d51ba8 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Thu, 21 Apr 2016 15:44:14 +0100
-Subject: [PATCH] bcm2835-i2s: Reduce the TX DREQ threshold
-
-TX FIFO overrun is thought to be the cause of channel swapping, so
-reducing the DREQ threshold seems reasonable and appears to be
-effective.
-
-See: https://github.com/raspberrypi/linux/issues/1417
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- sound/soc/bcm/bcm2835-i2s.c | 21 ++++++++++++++-------
- 1 file changed, 14 insertions(+), 7 deletions(-)
-
---- a/sound/soc/bcm/bcm2835-i2s.c
-+++ b/sound/soc/bcm/bcm2835-i2s.c
-@@ -555,15 +555,22 @@ static int bcm2835_i2s_hw_params(struct
-
- /* Setup the DMA parameters */
- regmap_update_bits(dev->i2s_regmap, BCM2835_I2S_CS_A_REG,
-- BCM2835_I2S_RXTHR(1)
-- | BCM2835_I2S_TXTHR(1)
-- | BCM2835_I2S_DMAEN, 0xffffffff);
-+ BCM2835_I2S_RXTHR(3)
-+ | BCM2835_I2S_TXTHR(3)
-+ | BCM2835_I2S_DMAEN,
-+ BCM2835_I2S_RXTHR(1)
-+ | BCM2835_I2S_TXTHR(1)
-+ | BCM2835_I2S_DMAEN);
-
- regmap_update_bits(dev->i2s_regmap, BCM2835_I2S_DREQ_A_REG,
-- BCM2835_I2S_TX_PANIC(0x10)
-- | BCM2835_I2S_RX_PANIC(0x30)
-- | BCM2835_I2S_TX(0x30)
-- | BCM2835_I2S_RX(0x20), 0xffffffff);
-+ BCM2835_I2S_TX_PANIC(0x7f)
-+ | BCM2835_I2S_RX_PANIC(0x7f)
-+ | BCM2835_I2S_TX(0x7f)
-+ | BCM2835_I2S_RX(0x7f),
-+ BCM2835_I2S_TX_PANIC(0x10)
-+ | BCM2835_I2S_RX_PANIC(0x30)
-+ | BCM2835_I2S_TX(0x20)
-+ | BCM2835_I2S_RX(0x20));
-
- /* Clear FIFOs */
- bcm2835_i2s_clear_fifos(dev, true, true);
diff --git a/target/linux/brcm2708/patches-4.4/0300-V4L2-Request-maximum-resolution-from-GPU.patch b/target/linux/brcm2708/patches-4.4/0300-V4L2-Request-maximum-resolution-from-GPU.patch
deleted file mode 100644
index edd95a1..0000000
--- a/target/linux/brcm2708/patches-4.4/0300-V4L2-Request-maximum-resolution-from-GPU.patch
+++ /dev/null
@@ -1,193 +0,0 @@
-From 4f0614de030f2a75be22a8f7ebc298e8260021cf Mon Sep 17 00:00:00 2001
-From: Dave Stevenson <6by9 at users.noreply.github.com>
-Date: Sat, 16 Apr 2016 23:09:54 +0100
-Subject: [PATCH] V4L2: Request maximum resolution from GPU
-
-Get resolution information about the sensors from the GPU
-and advertise it correctly.
-
-Signed-off-by: Dave Stevenson <6by9 at users.noreply.github.com>
----
- drivers/media/platform/bcm2835/bcm2835-camera.c | 59 +++++++++++++++++--------
- drivers/media/platform/bcm2835/bcm2835-camera.h | 3 +-
- 2 files changed, 43 insertions(+), 19 deletions(-)
-
---- a/drivers/media/platform/bcm2835/bcm2835-camera.c
-+++ b/drivers/media/platform/bcm2835/bcm2835-camera.c
-@@ -38,8 +38,6 @@
- #define BM2835_MMAL_MODULE_NAME "bcm2835-v4l2"
- #define MIN_WIDTH 16
- #define MIN_HEIGHT 16
--#define MAX_WIDTH 2592
--#define MAX_HEIGHT 1944
- #define MIN_BUFFER_SIZE (80*1024)
-
- #define MAX_VIDEO_MODE_WIDTH 1280
-@@ -729,11 +727,11 @@ static int vidioc_try_fmt_vid_overlay(st
- f->fmt.win.clipcount = 0;
- f->fmt.win.bitmap = NULL;
-
-- v4l_bound_align_image(&f->fmt.win.w.width, MIN_WIDTH, MAX_WIDTH, 1,
-- &f->fmt.win.w.height, MIN_HEIGHT, MAX_HEIGHT,
-+ v4l_bound_align_image(&f->fmt.win.w.width, MIN_WIDTH, dev->max_width, 1,
-+ &f->fmt.win.w.height, MIN_HEIGHT, dev->max_height,
- 1, 0);
-- v4l_bound_align_image(&f->fmt.win.w.left, MIN_WIDTH, MAX_WIDTH, 1,
-- &f->fmt.win.w.top, MIN_HEIGHT, MAX_HEIGHT,
-+ v4l_bound_align_image(&f->fmt.win.w.left, MIN_WIDTH, dev->max_width, 1,
-+ &f->fmt.win.w.top, MIN_HEIGHT, dev->max_height,
- 1, 0);
-
- v4l2_dbg(1, bcm2835_v4l2_debug, &dev->v4l2_dev,
-@@ -961,8 +959,9 @@ static int vidioc_try_fmt_vid_cap(struct
- "Clipping/aligning %dx%d format %08X\n",
- f->fmt.pix.width, f->fmt.pix.height, f->fmt.pix.pixelformat);
-
-- v4l_bound_align_image(&f->fmt.pix.width, MIN_WIDTH, MAX_WIDTH, 1,
-- &f->fmt.pix.height, MIN_HEIGHT, MAX_HEIGHT, 1, 0);
-+ v4l_bound_align_image(&f->fmt.pix.width, MIN_WIDTH, dev->max_width, 1,
-+ &f->fmt.pix.height, MIN_HEIGHT, dev->max_height,
-+ 1, 0);
- f->fmt.pix.bytesperline = f->fmt.pix.width * mfmt->ybbp;
-
- /* Image buffer has to be padded to allow for alignment, even though
-@@ -1301,9 +1300,10 @@ static int vidioc_s_fmt_vid_cap(struct f
- int vidioc_enum_framesizes(struct file *file, void *fh,
- struct v4l2_frmsizeenum *fsize)
- {
-+ struct bm2835_mmal_dev *dev = video_drvdata(file);
- static const struct v4l2_frmsize_stepwise sizes = {
-- MIN_WIDTH, MAX_WIDTH, 2,
-- MIN_HEIGHT, MAX_HEIGHT, 2
-+ MIN_WIDTH, 0, 2,
-+ MIN_HEIGHT, 0, 2
- };
- int i;
-
-@@ -1316,6 +1316,8 @@ int vidioc_enum_framesizes(struct file *
- return -EINVAL;
- fsize->type = V4L2_FRMSIZE_TYPE_STEPWISE;
- fsize->stepwise = sizes;
-+ fsize->stepwise.max_width = dev->max_width;
-+ fsize->stepwise.max_height = dev->max_height;
- return 0;
- }
-
-@@ -1323,6 +1325,7 @@ int vidioc_enum_framesizes(struct file *
- static int vidioc_enum_frameintervals(struct file *file, void *priv,
- struct v4l2_frmivalenum *fival)
- {
-+ struct bm2835_mmal_dev *dev = video_drvdata(file);
- int i;
-
- if (fival->index)
-@@ -1335,8 +1338,8 @@ static int vidioc_enum_frameintervals(st
- return -EINVAL;
-
- /* regarding width & height - we support any within range */
-- if (fival->width < MIN_WIDTH || fival->width > MAX_WIDTH ||
-- fival->height < MIN_HEIGHT || fival->height > MAX_HEIGHT)
-+ if (fival->width < MIN_WIDTH || fival->width > dev->max_width ||
-+ fival->height < MIN_HEIGHT || fival->height > dev->max_height)
- return -EINVAL;
-
- fival->type = V4L2_FRMIVAL_TYPE_CONTINUOUS;
-@@ -1499,12 +1502,17 @@ static struct video_device vdev_template
- .release = video_device_release_empty,
- };
-
--static int get_num_cameras(struct vchiq_mmal_instance *instance)
-+/* Returns the number of cameras, and also the max resolution supported
-+ * by those cameras.
-+ */
-+static int get_num_cameras(struct vchiq_mmal_instance *instance,
-+ unsigned int resolutions[][2], int num_resolutions)
- {
- int ret;
- struct vchiq_mmal_component *cam_info_component;
- struct mmal_parameter_camera_info_t cam_info = {0};
- int param_size = sizeof(cam_info);
-+ int i;
-
- /* create a camera_info component */
- ret = vchiq_mmal_component_init(instance, "camera_info",
-@@ -1520,6 +1528,14 @@ static int get_num_cameras(struct vchiq_
- ¶m_size)) {
- pr_info("Failed to get camera info\n");
- }
-+ for (i = 0;
-+ i < (cam_info.num_cameras > num_resolutions ?
-+ cam_info.num_cameras :
-+ num_resolutions);
-+ i++) {
-+ resolutions[i][0] = cam_info.cameras[i].max_width;
-+ resolutions[i][1] = cam_info.cameras[i].max_height;
-+ }
-
- vchiq_mmal_component_finalise(instance,
- cam_info_component);
-@@ -1528,12 +1544,13 @@ static int get_num_cameras(struct vchiq_
- }
-
- static int set_camera_parameters(struct vchiq_mmal_instance *instance,
-- struct vchiq_mmal_component *camera)
-+ struct vchiq_mmal_component *camera,
-+ struct bm2835_mmal_dev *dev)
- {
- int ret;
- struct mmal_parameter_camera_config cam_config = {
-- .max_stills_w = MAX_WIDTH,
-- .max_stills_h = MAX_HEIGHT,
-+ .max_stills_w = dev->max_width,
-+ .max_stills_h = dev->max_height,
- .stills_yuv422 = 1,
- .one_shot_stills = 1,
- .max_preview_video_w = (max_video_width > 1920) ?
-@@ -1576,7 +1593,8 @@ static int __init mmal_init(struct bm283
- }
-
- ret = set_camera_parameters(dev->instance,
-- dev->component[MMAL_COMPONENT_CAMERA]);
-+ dev->component[MMAL_COMPONENT_CAMERA],
-+ dev);
- if (ret < 0)
- goto unreg_camera;
-
-@@ -1838,12 +1856,15 @@ static int __init bm2835_mmal_init(void)
- int camera;
- unsigned int num_cameras;
- struct vchiq_mmal_instance *instance;
-+ unsigned int resolutions[MAX_BCM2835_CAMERAS][2];
-
- ret = vchiq_mmal_init(&instance);
- if (ret < 0)
- return ret;
-
-- num_cameras = get_num_cameras(instance);
-+ num_cameras = get_num_cameras(instance,
-+ resolutions,
-+ MAX_BCM2835_CAMERAS);
- if (num_cameras > MAX_BCM2835_CAMERAS)
- num_cameras = MAX_BCM2835_CAMERAS;
-
-@@ -1853,6 +1874,8 @@ static int __init bm2835_mmal_init(void)
- return -ENOMEM;
-
- dev->camera_num = camera;
-+ dev->max_width = resolutions[camera][0];
-+ dev->max_height = resolutions[camera][1];
-
- /* setup device defaults */
- dev->overlay.w.left = 150;
---- a/drivers/media/platform/bcm2835/bcm2835-camera.h
-+++ b/drivers/media/platform/bcm2835/bcm2835-camera.h
-@@ -107,7 +107,8 @@ struct bm2835_mmal_dev {
- } capture;
-
- unsigned int camera_num;
--
-+ unsigned int max_width;
-+ unsigned int max_height;
- };
-
- int bm2835_mmal_init_controls(
diff --git a/target/linux/brcm2708/patches-4.4/0301-ARM-bcm2835-add-i2s-gpio28-31-for-cm.patch b/target/linux/brcm2708/patches-4.4/0301-ARM-bcm2835-add-i2s-gpio28-31-for-cm.patch
deleted file mode 100644
index b16fb38..0000000
--- a/target/linux/brcm2708/patches-4.4/0301-ARM-bcm2835-add-i2s-gpio28-31-for-cm.patch
+++ /dev/null
@@ -1,62 +0,0 @@
-From ed7c9c36919e91a4859e146f6032910db24dfc7b Mon Sep 17 00:00:00 2001
-From: Martin Sperl <kernel at martin.sperl.org>
-Date: Sat, 23 Apr 2016 15:21:41 +0000
-Subject: [PATCH] ARM: bcm2835: add i2s-gpio28-31 for cm
-
-Add i2s-gpio28-31 overlay for compute module
-so that i2s is using gpio28-31
-
-Signed-off-by: Martin Sperl <kernel at martin.sperl.org>
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 6 ++++++
- arch/arm/boot/dts/overlays/i2s-gpio28-31-overlay.dts | 18 ++++++++++++++++++
- 3 files changed, 25 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/i2s-gpio28-31-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -37,6 +37,7 @@ dtbo-$(RPI_DT_OVERLAYS) += i2c-mux-pca95
- dtbo-$(RPI_DT_OVERLAYS) += i2c-pwm-pca9685a.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c0-bcm2708.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c1-bcm2708.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += i2s-gpio28-31.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2s-mmap.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += iqaudio-dac.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += iqaudio-dacplus.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -464,6 +464,12 @@ Params: sda1_pin GPIO pin
- default 4)
-
-
-+Name: i2s-gpio28-31
-+Info: move I2S function block to GPIO 28 to 31
-+Load: dtoverlay=i2s-gpio28-31
-+Params: <None>
-+
-+
- Name: i2s-mmap
- Info: Enables mmap support in the bcm2708-i2s driver
- Load: dtoverlay=i2s-mmap
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/i2s-gpio28-31-overlay.dts
-@@ -0,0 +1,18 @@
-+/*
-+ * Device tree overlay to move i2s to gpio 28 to 31 on CM
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2836", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&i2s_pins>;
-+ __overlay__ {
-+ brcm,pins = <28 29 30 31>;
-+ brcm,function = <6>; /* alt2 */
-+ };
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0302-drm-vc4-Add-DT-parameters-to-control-CMA-usage.patch b/target/linux/brcm2708/patches-4.4/0302-drm-vc4-Add-DT-parameters-to-control-CMA-usage.patch
deleted file mode 100644
index b4718b1..0000000
--- a/target/linux/brcm2708/patches-4.4/0302-drm-vc4-Add-DT-parameters-to-control-CMA-usage.patch
+++ /dev/null
@@ -1,75 +0,0 @@
-From fb40c5765f64ba63ecbd2d0a7abc25ee81714b6b Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Sun, 24 Apr 2016 17:28:15 +0100
-Subject: [PATCH] drm/vc4: Add DT parameters to control CMA usage
-
-Example: dtoverlay=vc4-kms-v3d,cma-128
-
-See: https://github.com/raspberrypi/linux/pull/1431
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/overlays/README | 8 +++--
- arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts | 36 ++++++++++++++++++++++
- 2 files changed, 42 insertions(+), 2 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -1023,8 +1023,12 @@ Name: vc4-kms-v3d
- Info: Enable Eric Anholt's DRM VC4 HDMI/HVS/V3D driver. Running startx or
- booting to GUI while this overlay is in use will cause interesting
- lockups.
--Load: dtoverlay=vc4-kms-v3d
--Params: <None>
-+Load: dtoverlay=vc4-kms-v3d,<param>
-+Params: cma-256 CMA is 256MB, 256MB-aligned (needs 1GB)
-+ cma-192 CMA is 192MB, 256MB-aligned (needs 1GB)
-+ cma-128 CMA is 128MB, 128MB-aligned
-+ cma-96 CMA is 96MB, 128MB-aligned
-+ cma-64 CMA is 64MB, 64MB-aligned
-
-
- Name: vga666
---- a/arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts
-@@ -94,4 +94,40 @@
- bootargs = "cma=256M at 256M";
- };
- };
-+
-+ fragment at 5 {
-+ target-path = "/chosen";
-+ __dormant__ {
-+ bootargs = "cma=192M at 256M";
-+ };
-+ };
-+
-+ fragment at 6 {
-+ target-path = "/chosen";
-+ __dormant__ {
-+ bootargs = "cma=128M at 128M";
-+ };
-+ };
-+
-+ fragment at 7 {
-+ target-path = "/chosen";
-+ __dormant__ {
-+ bootargs = "cma=96M at 128M";
-+ };
-+ };
-+
-+ fragment at 8 {
-+ target-path = "/chosen";
-+ __dormant__ {
-+ bootargs = "cma=64M at 64M";
-+ };
-+ };
-+
-+ __overrides__ {
-+ cma-256 = <0>,"+4-5-6-7-8";
-+ cma-192 = <0>,"-4+5-6-7-8";
-+ cma-128 = <0>,"-4-5+6-7-8";
-+ cma-96 = <0>,"-4-5-6+7-8";
-+ cma-64 = <0>,"-4-5-6-7+8";
-+ };
- };
diff --git a/target/linux/brcm2708/patches-4.4/0303-SQUASH-BCM270X_DT-Add-make-rule-for-sdio-1bit.patch b/target/linux/brcm2708/patches-4.4/0303-SQUASH-BCM270X_DT-Add-make-rule-for-sdio-1bit.patch
deleted file mode 100644
index 682a67a..0000000
--- a/target/linux/brcm2708/patches-4.4/0303-SQUASH-BCM270X_DT-Add-make-rule-for-sdio-1bit.patch
+++ /dev/null
@@ -1,22 +0,0 @@
-From 8ae1bbb4987b83c3c63f83fda4316870d219de31 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 25 Apr 2016 10:43:36 +0100
-Subject: [PATCH] SQUASH: BCM270X_DT: Add make rule for sdio-1bit
-
-See: https://github.com/raspberrypi/linux/pull/1301
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- 1 file changed, 1 insertion(+)
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -66,6 +66,7 @@ dtbo-$(RPI_DT_OVERLAYS) += rpi-proto.dtb
- dtbo-$(RPI_DT_OVERLAYS) += rpi-sense.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += sdhost.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += sdio.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += sdio-1bit.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += sdtweak.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += smi-dev.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += smi-nand.dtbo
diff --git a/target/linux/brcm2708/patches-4.4/0304-dts-add-overlay-for-pitft22.patch b/target/linux/brcm2708/patches-4.4/0304-dts-add-overlay-for-pitft22.patch
deleted file mode 100644
index 47910e2..0000000
--- a/target/linux/brcm2708/patches-4.4/0304-dts-add-overlay-for-pitft22.patch
+++ /dev/null
@@ -1,123 +0,0 @@
-From e0a2d28dadbb8c41f4e4b7eb46658b79f63e23bf Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Petter=20Mab=C3=A4cker?= <petter at technux.se>
-Date: Fri, 8 Jan 2016 09:02:44 +0100
-Subject: [PATCH] dts: add overlay for pitft22
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Add the pitft22 overlay from adafruit Adafruit-Pi-Kernel-o-Matic repo:
-https://github.com/adafruit/Adafruit-Pi-Kernel-o-Matic
-
-Signed-off-by: Petter Mabäcker <petter at technux.se>
-Signed-off-by: Andrei Gherzan <andrei at resin.io>
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 12 +++++
- arch/arm/boot/dts/overlays/pitft22-overlay.dts | 69 ++++++++++++++++++++++++++
- 3 files changed, 82 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/pitft22-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -51,6 +51,7 @@ dtbo-$(RPI_DT_OVERLAYS) += pi3-disable-b
- dtbo-$(RPI_DT_OVERLAYS) += pi3-miniuart-bt.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += piscreen.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += piscreen2r.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += pitft22.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += pitft28-capacitive.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += pitft28-resistive.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += pps-gpio.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -644,6 +644,18 @@ Params: speed Display
- xohms Touchpanel sensitivity (X-plate resistance)
-
-
-+Name: pitft22
-+Info: Adafruit PiTFT 2.2" screen
-+Load: dtoverlay=pitft22,<param>=<val>
-+Params: speed Display SPI bus speed
-+
-+ rotate Display rotation {0,90,180,270}
-+
-+ fps Delay between frame updates
-+
-+ debug Debug output level {0-7}
-+
-+
- Name: pitft28-capacitive
- Info: Adafruit PiTFT 2.8" capacitive touch screen
- Load: dtoverlay=pitft28-capacitive,<param>=<val>
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/pitft22-overlay.dts
-@@ -0,0 +1,69 @@
-+/*
-+ * Device Tree overlay for pitft by Adafruit
-+ *
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ status = "okay";
-+
-+ spidev at 0{
-+ status = "disabled";
-+ };
-+
-+ spidev at 1{
-+ status = "disabled";
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ pitft_pins: pitft_pins {
-+ brcm,pins = <25>;
-+ brcm,function = <1>; /* out */
-+ brcm,pull = <0>; /* none */
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ /* needed to avoid dtc warning */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ pitft: pitft at 0{
-+ compatible = "ilitek,ili9340";
-+ reg = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pitft_pins>;
-+
-+ spi-max-frequency = <32000000>;
-+ rotate = <90>;
-+ fps = <25>;
-+ bgr;
-+ buswidth = <8>;
-+ dc-gpios = <&gpio 25 0>;
-+ debug = <0>;
-+ };
-+
-+ };
-+ };
-+
-+ __overrides__ {
-+ speed = <&pitft>,"spi-max-frequency:0";
-+ rotate = <&pitft>,"rotate:0";
-+ fps = <&pitft>,"fps:0";
-+ debug = <&pitft>,"debug:0";
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0305-BCM270X_DT-Sound-DT-adjustments-for-Dynamic-DT.patch b/target/linux/brcm2708/patches-4.4/0305-BCM270X_DT-Sound-DT-adjustments-for-Dynamic-DT.patch
deleted file mode 100644
index dadf9dd..0000000
--- a/target/linux/brcm2708/patches-4.4/0305-BCM270X_DT-Sound-DT-adjustments-for-Dynamic-DT.patch
+++ /dev/null
@@ -1,578 +0,0 @@
-From e1a02b311f61d83f33994b8510ba4c1b7d2f3026 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Tue, 26 Apr 2016 10:44:59 +0100
-Subject: [PATCH] BCM270X_DT: Sound DT adjustments for Dynamic DT
-
-There are a number of issues when loading and unloading overlays for
-sound cards:
-1) The "sound" and "audio" nodes must be children of a bus node, such
- as "/soc", otherwise the DT changes don't result in platform devices
- being created and deleted.
-2) The "/sound" node must have a "disabled" status property, otherwise
- setting the status to "okay" won't be detected.
-3) ALSA doesn't like having components unloaded under its feet, and it
- is easy to deadlock or crash. Ordering the overlay fragments so that
- the sound card appears last avoids this problem.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/bcm2708_common.dtsi | 23 +++++++++---------
- .../dts/overlays/akkordion-iqdacplus-overlay.dts | 28 +++++++++++-----------
- .../boot/dts/overlays/boomberry-dac-overlay.dts | 22 ++++++++---------
- .../boot/dts/overlays/boomberry-digi-overlay.dts | 20 ++++++++--------
- .../boot/dts/overlays/hifiberry-amp-overlay.dts | 20 ++++++++--------
- .../boot/dts/overlays/hifiberry-dac-overlay.dts | 22 ++++++++---------
- .../dts/overlays/hifiberry-dacplus-overlay.dts | 22 ++++++++---------
- .../boot/dts/overlays/hifiberry-digi-overlay.dts | 20 ++++++++--------
- arch/arm/boot/dts/overlays/iqaudio-dac-overlay.dts | 20 ++++++++--------
- .../boot/dts/overlays/iqaudio-dacplus-overlay.dts | 22 ++++++++---------
- arch/arm/boot/dts/overlays/raspidac3-overlay.dts | 20 ++++++++--------
- arch/arm/boot/dts/overlays/rpi-dac-overlay.dts | 22 ++++++++---------
- arch/arm/boot/dts/overlays/rpi-proto-overlay.dts | 20 ++++++++--------
- 13 files changed, 141 insertions(+), 140 deletions(-)
-
---- a/arch/arm/boot/dts/bcm2708_common.dtsi
-+++ b/arch/arm/boot/dts/bcm2708_common.dtsi
-@@ -34,17 +34,6 @@
- clocks = &clocks;
- };
-
-- /* Onboard audio */
-- audio: audio {
-- compatible = "brcm,bcm2835-audio";
-- brcm,pwm-channels = <8>;
-- status = "disabled";
-- };
--
-- /* External sound card */
-- sound: sound {
-- };
--
- soc: soc {
- compatible = "simple-bus";
- #address-cells = <1>;
-@@ -313,6 +302,18 @@
- compatible = "brcm,bcm2835-thermal";
- firmware = <&firmware>;
- };
-+
-+ /* Onboard audio */
-+ audio: audio {
-+ compatible = "brcm,bcm2835-audio";
-+ brcm,pwm-channels = <8>;
-+ status = "disabled";
-+ };
-+
-+ /* External sound card */
-+ sound: sound {
-+ status = "disabled";
-+ };
- };
-
- clocks: clocks {
---- a/arch/arm/boot/dts/overlays/akkordion-iqdacplus-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/akkordion-iqdacplus-overlay.dts
-@@ -6,25 +6,13 @@
- compatible = "brcm,bcm2708";
-
- fragment at 0 {
-- target = <&sound>;
-- frag0: __overlay__ {
-- compatible = "iqaudio,iqaudio-dac";
-- card_name = "Akkordion";
-- dai_name = "IQaudIO DAC";
-- dai_stream_name = "IQaudIO DAC HiFi";
-- i2s-controller = <&i2s>;
-- status = "okay";
-- };
-- };
--
-- fragment at 1 {
- target = <&i2s>;
- __overlay__ {
- status = "okay";
- };
- };
-
-- fragment at 2 {
-+ fragment at 1 {
- target = <&i2c1>;
- __overlay__ {
- #address-cells = <1>;
-@@ -40,7 +28,19 @@
- };
- };
-
-+ fragment at 2 {
-+ target = <&sound>;
-+ frag2: __overlay__ {
-+ compatible = "iqaudio,iqaudio-dac";
-+ card_name = "Akkordion";
-+ dai_name = "IQaudIO DAC";
-+ dai_stream_name = "IQaudIO DAC HiFi";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
-+
- __overrides__ {
-- 24db_digital_gain = <&frag0>,"iqaudio,24db_digital_gain?";
-+ 24db_digital_gain = <&frag2>,"iqaudio,24db_digital_gain?";
- };
- };
---- a/arch/arm/boot/dts/overlays/boomberry-dac-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/boomberry-dac-overlay.dts
-@@ -6,22 +6,13 @@
- compatible = "brcm,bcm2708";
-
- fragment at 0 {
-- target = <&sound>;
-- frag0: __overlay__ {
-- compatible = "boomberry,boomberry-dac";
-- i2s-controller = <&i2s>;
-- status = "okay";
-- };
-- };
--
-- fragment at 1 {
- target = <&i2s>;
- __overlay__ {
- status = "okay";
- };
- };
-
-- fragment at 2 {
-+ fragment at 1 {
- target = <&i2c1>;
- __overlay__ {
- #address-cells = <1>;
-@@ -37,7 +28,16 @@
- };
- };
-
-+ fragment at 2 {
-+ target = <&sound>;
-+ frag2: __overlay__ {
-+ compatible = "boomberry,boomberry-dac";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
-+
- __overrides__ {
-- 24db_digital_gain = <&frag0>,"boomberry,24db_digital_gain?";
-+ 24db_digital_gain = <&frag2>,"boomberry,24db_digital_gain?";
- };
- };
---- a/arch/arm/boot/dts/overlays/boomberry-digi-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/boomberry-digi-overlay.dts
-@@ -6,22 +6,13 @@
- compatible = "brcm,bcm2708";
-
- fragment at 0 {
-- target = <&sound>;
-- __overlay__ {
-- compatible = "boomberry,boomberry-digi";
-- i2s-controller = <&i2s>;
-- status = "okay";
-- };
-- };
--
-- fragment at 1 {
- target = <&i2s>;
- __overlay__ {
- status = "okay";
- };
- };
-
-- fragment at 2 {
-+ fragment at 1 {
- target = <&i2c1>;
- __overlay__ {
- #address-cells = <1>;
-@@ -36,4 +27,13 @@
- };
- };
- };
-+
-+ fragment at 2 {
-+ target = <&sound>;
-+ __overlay__ {
-+ compatible = "boomberry,boomberry-digi";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
- };
---- a/arch/arm/boot/dts/overlays/hifiberry-amp-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/hifiberry-amp-overlay.dts
-@@ -6,22 +6,13 @@
- compatible = "brcm,bcm2708";
-
- fragment at 0 {
-- target = <&sound>;
-- __overlay__ {
-- compatible = "hifiberry,hifiberry-amp";
-- i2s-controller = <&i2s>;
-- status = "okay";
-- };
-- };
--
-- fragment at 1 {
- target = <&i2s>;
- __overlay__ {
- status = "okay";
- };
- };
-
-- fragment at 2 {
-+ fragment at 1 {
- target = <&i2c1>;
- __overlay__ {
- #address-cells = <1>;
-@@ -36,4 +27,13 @@
- };
- };
- };
-+
-+ fragment at 2 {
-+ target = <&sound>;
-+ __overlay__ {
-+ compatible = "hifiberry,hifiberry-amp";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
- };
---- a/arch/arm/boot/dts/overlays/hifiberry-dac-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/hifiberry-dac-overlay.dts
-@@ -6,23 +6,14 @@
- compatible = "brcm,bcm2708";
-
- fragment at 0 {
-- target = <&sound>;
-- __overlay__ {
-- compatible = "hifiberry,hifiberry-dac";
-- i2s-controller = <&i2s>;
-- status = "okay";
-- };
-- };
--
-- fragment at 1 {
- target = <&i2s>;
- __overlay__ {
- status = "okay";
- };
- };
-
-- fragment at 2 {
-- target-path = "/";
-+ fragment at 1 {
-+ target = <&soc>;
- __overlay__ {
- pcm5102a-codec {
- #sound-dai-cells = <0>;
-@@ -31,4 +22,13 @@
- };
- };
- };
-+
-+ fragment at 2 {
-+ target = <&sound>;
-+ __overlay__ {
-+ compatible = "hifiberry,hifiberry-dac";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
- };
---- a/arch/arm/boot/dts/overlays/hifiberry-dacplus-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/hifiberry-dacplus-overlay.dts
-@@ -16,22 +16,13 @@
- };
-
- fragment at 1 {
-- target = <&sound>;
-- frag1: __overlay__ {
-- compatible = "hifiberry,hifiberry-dacplus";
-- i2s-controller = <&i2s>;
-- status = "okay";
-- };
-- };
--
-- fragment at 2 {
- target = <&i2s>;
- __overlay__ {
- status = "okay";
- };
- };
-
-- fragment at 3 {
-+ fragment at 2 {
- target = <&i2c1>;
- __overlay__ {
- #address-cells = <1>;
-@@ -48,7 +39,16 @@
- };
- };
-
-+ fragment at 3 {
-+ target = <&sound>;
-+ frag3: __overlay__ {
-+ compatible = "hifiberry,hifiberry-dacplus";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
-+
- __overrides__ {
-- 24db_digital_gain = <&frag1>,"hifiberry,24db_digital_gain?";
-+ 24db_digital_gain = <&frag3>,"hifiberry,24db_digital_gain?";
- };
- };
---- a/arch/arm/boot/dts/overlays/hifiberry-digi-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/hifiberry-digi-overlay.dts
-@@ -6,22 +6,13 @@
- compatible = "brcm,bcm2708";
-
- fragment at 0 {
-- target = <&sound>;
-- __overlay__ {
-- compatible = "hifiberry,hifiberry-digi";
-- i2s-controller = <&i2s>;
-- status = "okay";
-- };
-- };
--
-- fragment at 1 {
- target = <&i2s>;
- __overlay__ {
- status = "okay";
- };
- };
-
-- fragment at 2 {
-+ fragment at 1 {
- target = <&i2c1>;
- __overlay__ {
- #address-cells = <1>;
-@@ -36,4 +27,13 @@
- };
- };
- };
-+
-+ fragment at 2 {
-+ target = <&sound>;
-+ __overlay__ {
-+ compatible = "hifiberry,hifiberry-digi";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
- };
---- a/arch/arm/boot/dts/overlays/iqaudio-dac-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/iqaudio-dac-overlay.dts
-@@ -6,22 +6,13 @@
- compatible = "brcm,bcm2708";
-
- fragment at 0 {
-- target = <&sound>;
-- __overlay__ {
-- compatible = "iqaudio,iqaudio-dac";
-- i2s-controller = <&i2s>;
-- status = "okay";
-- };
-- };
--
-- fragment at 1 {
- target = <&i2s>;
- __overlay__ {
- status = "okay";
- };
- };
-
-- fragment at 2 {
-+ fragment at 1 {
- target = <&i2c1>;
- __overlay__ {
- #address-cells = <1>;
-@@ -36,4 +27,13 @@
- };
- };
- };
-+
-+ fragment at 2 {
-+ target = <&sound>;
-+ __overlay__ {
-+ compatible = "iqaudio,iqaudio-dac";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
- };
---- a/arch/arm/boot/dts/overlays/iqaudio-dacplus-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/iqaudio-dacplus-overlay.dts
-@@ -6,22 +6,13 @@
- compatible = "brcm,bcm2708";
-
- fragment at 0 {
-- target = <&sound>;
-- frag0: __overlay__ {
-- compatible = "iqaudio,iqaudio-dac";
-- i2s-controller = <&i2s>;
-- status = "okay";
-- };
-- };
--
-- fragment at 1 {
- target = <&i2s>;
- __overlay__ {
- status = "okay";
- };
- };
-
-- fragment at 2 {
-+ fragment at 1 {
- target = <&i2c1>;
- __overlay__ {
- #address-cells = <1>;
-@@ -37,7 +28,16 @@
- };
- };
-
-+ fragment at 2 {
-+ target = <&sound>;
-+ frag2: __overlay__ {
-+ compatible = "iqaudio,iqaudio-dac";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
-+
- __overrides__ {
-- 24db_digital_gain = <&frag0>,"iqaudio,24db_digital_gain?";
-+ 24db_digital_gain = <&frag2>,"iqaudio,24db_digital_gain?";
- };
- };
---- a/arch/arm/boot/dts/overlays/raspidac3-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/raspidac3-overlay.dts
-@@ -6,22 +6,13 @@
- compatible = "brcm,bcm2708";
-
- fragment at 0 {
-- target = <&sound>;
-- __overlay__ {
-- compatible = "jg,raspidacv3";
-- i2s-controller = <&i2s>;
-- status = "okay";
-- };
-- };
--
-- fragment at 1 {
- target = <&i2s>;
- __overlay__ {
- status = "okay";
- };
- };
-
-- fragment at 2 {
-+ fragment at 1 {
- target = <&i2c1>;
- __overlay__ {
- #address-cells = <1>;
-@@ -42,4 +33,13 @@
- };
- };
- };
-+
-+ fragment at 2 {
-+ target = <&sound>;
-+ __overlay__ {
-+ compatible = "jg,raspidacv3";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
- };
---- a/arch/arm/boot/dts/overlays/rpi-dac-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/rpi-dac-overlay.dts
-@@ -6,23 +6,14 @@
- compatible = "brcm,bcm2708";
-
- fragment at 0 {
-- target = <&sound>;
-- __overlay__ {
-- compatible = "rpi,rpi-dac";
-- i2s-controller = <&i2s>;
-- status = "okay";
-- };
-- };
--
-- fragment at 1 {
- target = <&i2s>;
- __overlay__ {
- status = "okay";
- };
- };
-
-- fragment at 2 {
-- target-path = "/";
-+ fragment at 1 {
-+ target = <&soc>;
- __overlay__ {
- pcm1794a-codec {
- #sound-dai-cells = <0>;
-@@ -31,4 +22,13 @@
- };
- };
- };
-+
-+ fragment at 2 {
-+ target = <&sound>;
-+ __overlay__ {
-+ compatible = "rpi,rpi-dac";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
- };
---- a/arch/arm/boot/dts/overlays/rpi-proto-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/rpi-proto-overlay.dts
-@@ -6,22 +6,13 @@
- compatible = "brcm,bcm2708";
-
- fragment at 0 {
-- target = <&sound>;
-- __overlay__ {
-- compatible = "rpi,rpi-proto";
-- i2s-controller = <&i2s>;
-- status = "okay";
-- };
-- };
--
-- fragment at 1 {
- target = <&i2s>;
- __overlay__ {
- status = "okay";
- };
- };
-
-- fragment at 2 {
-+ fragment at 1 {
- target = <&i2c1>;
- __overlay__ {
- #address-cells = <1>;
-@@ -36,4 +27,13 @@
- };
- };
- };
-+
-+ fragment at 2 {
-+ target = <&sound>;
-+ __overlay__ {
-+ compatible = "rpi,rpi-proto";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
- };
diff --git a/target/linux/brcm2708/patches-4.4/0306-BCM270X_DT-Fix-codec-use-in-hifiberry-dac-overlay.patch b/target/linux/brcm2708/patches-4.4/0306-BCM270X_DT-Fix-codec-use-in-hifiberry-dac-overlay.patch
deleted file mode 100644
index 9dfdcfb..0000000
--- a/target/linux/brcm2708/patches-4.4/0306-BCM270X_DT-Fix-codec-use-in-hifiberry-dac-overlay.patch
+++ /dev/null
@@ -1,21 +0,0 @@
-From 875783b480b4fd3e227f1d81d187e3675703c8b8 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Wed, 27 Apr 2016 12:01:41 +0100
-Subject: [PATCH] BCM270X_DT: Fix codec use in hifiberry-dac overlay
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/overlays/hifiberry-dac-overlay.dts | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/arch/arm/boot/dts/overlays/hifiberry-dac-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/hifiberry-dac-overlay.dts
-@@ -13,7 +13,7 @@
- };
-
- fragment at 1 {
-- target = <&soc>;
-+ target-path = "/";
- __overlay__ {
- pcm5102a-codec {
- #sound-dai-cells = <0>;
diff --git a/target/linux/brcm2708/patches-4.4/0309-Revert-bcm2835-log-which-channel-map-is-set.patch b/target/linux/brcm2708/patches-4.4/0309-Revert-bcm2835-log-which-channel-map-is-set.patch
deleted file mode 100644
index a6f09d8..0000000
--- a/target/linux/brcm2708/patches-4.4/0309-Revert-bcm2835-log-which-channel-map-is-set.patch
+++ /dev/null
@@ -1,33 +0,0 @@
-From de42d50472397833d39f8cc96e5e906ba45cd450 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Fri, 29 Apr 2016 17:27:33 +0100
-Subject: [PATCH] Revert "bcm2835: log which channel map is set"
-
-This reverts commit cd560b8658868d9652ab31754e02f86daf6831ba.
----
- sound/arm/bcm2835-vchiq.c | 5 -----
- 1 file changed, 5 deletions(-)
-
---- a/sound/arm/bcm2835-vchiq.c
-+++ b/sound/arm/bcm2835-vchiq.c
-@@ -596,11 +596,8 @@ int bcm2835_audio_set_params(bcm2835_als
- instance->result = -1;
-
- if (alsa_stream->chip->cea_chmap >= 0) {
-- LOG_INFO("Using application requested channel map: %d\n",
-- alsa_stream->chip->cea_chmap);
- chmap_value = (unsigned)alsa_stream->chip->cea_chmap << 24;
- } else {
-- LOG_INFO("Using fallback channel map.\n");
- /* fallback layouts for applications which do not use chmap API */
- chmap_value = 0x00;
- switch (channels) {
-@@ -617,8 +614,6 @@ int bcm2835_audio_set_params(bcm2835_als
- for (i = 0; i < 8; i++)
- chmap_value |= alsa_stream->chip->map_channels[i] << (i * 3);
-
-- LOG_INFO("Requesting AUDS channel map: 0x%lx\n", (long)chmap_value);
--
- m.type = VC_AUDIO_MSG_TYPE_CONFIG;
- m.u.config.channels = channels;
- m.u.config.samplerate = samplerate;
diff --git a/target/linux/brcm2708/patches-4.4/0310-Revert-bcm2835-add-fallback-channel-layouts-if-chann.patch b/target/linux/brcm2708/patches-4.4/0310-Revert-bcm2835-add-fallback-channel-layouts-if-chann.patch
deleted file mode 100644
index e56219f..0000000
--- a/target/linux/brcm2708/patches-4.4/0310-Revert-bcm2835-add-fallback-channel-layouts-if-chann.patch
+++ /dev/null
@@ -1,31 +0,0 @@
-From 7173096d92c31748fe2af2943a3d44d8d8250418 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Fri, 29 Apr 2016 17:27:35 +0100
-Subject: [PATCH] Revert "bcm2835: add fallback channel layouts if channel map
- API is not used"
-
-This reverts commit ceacfff9f86f89826dbc8a6df667f485894327d1.
----
- sound/arm/bcm2835-vchiq.c | 11 +----------
- 1 file changed, 1 insertion(+), 10 deletions(-)
-
---- a/sound/arm/bcm2835-vchiq.c
-+++ b/sound/arm/bcm2835-vchiq.c
-@@ -598,16 +598,7 @@ int bcm2835_audio_set_params(bcm2835_als
- if (alsa_stream->chip->cea_chmap >= 0) {
- chmap_value = (unsigned)alsa_stream->chip->cea_chmap << 24;
- } else {
-- /* fallback layouts for applications which do not use chmap API */
-- chmap_value = 0x00;
-- switch (channels) {
-- case 3: chmap_value = 0x01; break;
-- case 4: chmap_value = 0x03; break;
-- case 5: chmap_value = 0x07; break;
-- case 6: chmap_value = 0x0b; break;
-- case 7: chmap_value = 0x0f; break;
-- case 8: chmap_value = 0x13; break;
-- }
-+ chmap_value = 0; /* force stereo */
- for (i = 0; i < 8; i++)
- alsa_stream->chip->map_channels[i] = i;
- }
diff --git a/target/linux/brcm2708/patches-4.4/0311-Revert-bcm2835-do-not-require-substream-for-accessin.patch b/target/linux/brcm2708/patches-4.4/0311-Revert-bcm2835-do-not-require-substream-for-accessin.patch
deleted file mode 100644
index 4993e41..0000000
--- a/target/linux/brcm2708/patches-4.4/0311-Revert-bcm2835-do-not-require-substream-for-accessin.patch
+++ /dev/null
@@ -1,51 +0,0 @@
-From ba83dd0869f15c33c016de9e061e15cca66327bd Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Fri, 29 Apr 2016 17:27:36 +0100
-Subject: [PATCH] Revert "bcm2835: do not require substream for accessing chmap
- ctl"
-
-This reverts commit a05b4815196018c329ea98c24205bc6fa9c097e0.
----
- sound/arm/bcm2835-ctl.c | 10 +++++++++-
- 1 file changed, 9 insertions(+), 1 deletion(-)
-
---- a/sound/arm/bcm2835-ctl.c
-+++ b/sound/arm/bcm2835-ctl.c
-@@ -489,6 +489,8 @@ static int snd_bcm2835_chmap_ctl_get(str
- {
- struct snd_pcm_chmap *info = snd_kcontrol_chip(kcontrol);
- bcm2835_chip_t *chip = info->private_data;
-+ unsigned int idx = snd_ctl_get_ioffidx(kcontrol, &ucontrol->id);
-+ struct snd_pcm_substream *substream = snd_pcm_chmap_substream(info, idx);
- struct cea_channel_speaker_allocation *ch = NULL;
- int res = 0;
- int cur = 0;
-@@ -497,6 +499,11 @@ static int snd_bcm2835_chmap_ctl_get(str
- if (mutex_lock_interruptible(&chip->audio_mutex))
- return -EINTR;
-
-+ if (!substream || !substream->runtime) {
-+ res = -ENODEV;
-+ goto unlock;
-+ }
-+
- for (i = 0; i < ARRAY_SIZE(channel_allocations); i++) {
- if (channel_allocations[i].ca_index == chip->cea_chmap)
- ch = &channel_allocations[i];
-@@ -514,6 +521,7 @@ static int snd_bcm2835_chmap_ctl_get(str
- while (cur < 8)
- ucontrol->value.integer.value[cur++] = SNDRV_CHMAP_NA;
-
-+unlock:
- mutex_unlock(&chip->audio_mutex);
- return res;
- }
-@@ -533,7 +541,7 @@ static int snd_bcm2835_chmap_ctl_put(str
- return -EINTR;
-
- if (!substream || !substream->runtime) {
-- /* ignore and return success for the sake of alsactl */
-+ res = -ENODEV;
- goto unlock;
- }
-
diff --git a/target/linux/brcm2708/patches-4.4/0312-Revert-bcm2835-interpolate-audio-delay.patch b/target/linux/brcm2708/patches-4.4/0312-Revert-bcm2835-interpolate-audio-delay.patch
deleted file mode 100644
index 66e06ab..0000000
--- a/target/linux/brcm2708/patches-4.4/0312-Revert-bcm2835-interpolate-audio-delay.patch
+++ /dev/null
@@ -1,70 +0,0 @@
-From 168e9978c48f0bc90618b6bb1de412a87f97805d Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Fri, 29 Apr 2016 17:27:37 +0100
-Subject: [PATCH] Revert "bcm2835: interpolate audio delay"
-
-This reverts commit 83eca613d0eddd2c8299f114b8fe573ccaffdefc.
----
- sound/arm/bcm2835-pcm.c | 12 +-----------
- sound/arm/bcm2835.h | 1 -
- 2 files changed, 1 insertion(+), 12 deletions(-)
-
---- a/sound/arm/bcm2835-pcm.c
-+++ b/sound/arm/bcm2835-pcm.c
-@@ -25,7 +25,7 @@
- /* hardware definition */
- static struct snd_pcm_hardware snd_bcm2835_playback_hw = {
- .info = (SNDRV_PCM_INFO_INTERLEAVED | SNDRV_PCM_INFO_BLOCK_TRANSFER |
-- SNDRV_PCM_INFO_MMAP | SNDRV_PCM_INFO_MMAP_VALID | SNDRV_PCM_INFO_BATCH),
-+ SNDRV_PCM_INFO_MMAP | SNDRV_PCM_INFO_MMAP_VALID),
- .formats = SNDRV_PCM_FMTBIT_U8 | SNDRV_PCM_FMTBIT_S16_LE,
- .rates = SNDRV_PCM_RATE_CONTINUOUS | SNDRV_PCM_RATE_8000_48000,
- .rate_min = 8000,
-@@ -99,8 +99,6 @@ static irqreturn_t bcm2835_playback_fifo
- alsa_stream->pos %= alsa_stream->buffer_size;
- }
-
-- alsa_stream->interpolate_start = ktime_get_ns();
--
- if (alsa_stream->substream) {
- if (new_period)
- snd_pcm_period_elapsed(alsa_stream->substream);
-@@ -401,7 +399,6 @@ static int snd_bcm2835_pcm_prepare(struc
- alsa_stream->buffer_size = snd_pcm_lib_buffer_bytes(substream);
- alsa_stream->period_size = snd_pcm_lib_period_bytes(substream);
- alsa_stream->pos = 0;
-- alsa_stream->interpolate_start = ktime_get_ns();
-
- audio_debug("buffer_size=%d, period_size=%d pos=%d frame_bits=%d\n",
- alsa_stream->buffer_size, alsa_stream->period_size,
-@@ -498,7 +495,6 @@ snd_bcm2835_pcm_pointer(struct snd_pcm_s
- {
- struct snd_pcm_runtime *runtime = substream->runtime;
- bcm2835_alsa_stream_t *alsa_stream = runtime->private_data;
-- u64 now = ktime_get_ns();
-
- audio_info(" .. IN\n");
-
-@@ -507,12 +503,6 @@ snd_bcm2835_pcm_pointer(struct snd_pcm_s
- frames_to_bytes(runtime, runtime->control->appl_ptr),
- alsa_stream->pos);
-
-- /* Give userspace better delay reporting by interpolating between GPU
-- * notifications, assuming audio speed is close enough to the clock
-- * used for ktime */
-- if (alsa_stream->interpolate_start && alsa_stream->interpolate_start < now)
-- runtime->delay = -(int)div_u64((now - alsa_stream->interpolate_start) * runtime->rate, 1000000000);
--
- audio_info(" .. OUT\n");
- return snd_pcm_indirect_playback_pointer(substream,
- &alsa_stream->pcm_indirect,
---- a/sound/arm/bcm2835.h
-+++ b/sound/arm/bcm2835.h
-@@ -137,7 +137,6 @@ typedef struct bcm2835_alsa_stream {
- unsigned int pos;
- unsigned int buffer_size;
- unsigned int period_size;
-- u64 interpolate_start;
-
- uint32_t enable_fifo_irq;
- irq_handler_t fifo_irq_handler;
diff --git a/target/linux/brcm2708/patches-4.4/0313-Revert-bcm2835-only-allow-stereo-if-analogue-jack-is.patch b/target/linux/brcm2708/patches-4.4/0313-Revert-bcm2835-only-allow-stereo-if-analogue-jack-is.patch
deleted file mode 100644
index a2d0288..0000000
--- a/target/linux/brcm2708/patches-4.4/0313-Revert-bcm2835-only-allow-stereo-if-analogue-jack-is.patch
+++ /dev/null
@@ -1,49 +0,0 @@
-From 27209aa2a0ff06e9941ce3e4e484021f996a28c5 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Fri, 29 Apr 2016 17:28:06 +0100
-Subject: [PATCH] Revert "bcm2835: only allow stereo if analogue jack is
- selected"
-
-This reverts commit 5f7049894f47b3836838cd68e29ee883179c80b3.
----
- sound/arm/bcm2835-ctl.c | 12 ------------
- 1 file changed, 12 deletions(-)
-
---- a/sound/arm/bcm2835-ctl.c
-+++ b/sound/arm/bcm2835-ctl.c
-@@ -423,16 +423,9 @@ static struct cea_channel_speaker_alloca
- { .ca_index = 0x31, .speakers = { FRW, FLW, RR, RL, FC, LFE, FR, FL } },
- };
-
--static int uses_analogue(bcm2835_chip_t *chip)
--{
-- return chip->dest == 1;
--}
--
- static int snd_bcm2835_chmap_ctl_tlv(struct snd_kcontrol *kcontrol, int op_flag,
- unsigned int size, unsigned int __user *tlv)
- {
-- struct snd_pcm_chmap *info = snd_kcontrol_chip(kcontrol);
-- bcm2835_chip_t *chip = info->private_data;
- unsigned int __user *dst;
- int count = 0;
- int i;
-@@ -449,9 +442,6 @@ static int snd_bcm2835_chmap_ctl_tlv(str
- int chs_bytes;
- int c;
-
-- if (i > 0 && uses_analogue(chip))
-- break;
--
- for (c = 0; c < 8; c++) {
- if (ch->speakers[c])
- num_chs++;
-@@ -562,8 +552,6 @@ static int snd_bcm2835_chmap_ctl_put(str
- int matches = 1;
- int cur = 0;
- int x;
-- if (i > 0 && uses_analogue(chip))
-- break;
- memset(remap, 0, sizeof(remap));
- for (x = 0; x < substream->runtime->channels; x++) {
- int sp = ucontrol->value.integer.value[x];
diff --git a/target/linux/brcm2708/patches-4.4/0314-Revert-bcm2835-always-use-2-4-8-channels-for-multich.patch b/target/linux/brcm2708/patches-4.4/0314-Revert-bcm2835-always-use-2-4-8-channels-for-multich.patch
deleted file mode 100644
index 29502fb..0000000
--- a/target/linux/brcm2708/patches-4.4/0314-Revert-bcm2835-always-use-2-4-8-channels-for-multich.patch
+++ /dev/null
@@ -1,135 +0,0 @@
-From 87879e01254dd42b4600cb91d593802293a471cf Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Fri, 29 Apr 2016 17:28:08 +0100
-Subject: [PATCH] Revert "bcm2835: always use 2/4/8 channels for multichannel
- layouts"
-
-This reverts commit 06931f74092d86087144f070b06a4444df8b444b.
----
- sound/arm/bcm2835-ctl.c | 89 ++++++++++++++++++++++++-------------------------
- 1 file changed, 44 insertions(+), 45 deletions(-)
-
---- a/sound/arm/bcm2835-ctl.c
-+++ b/sound/arm/bcm2835-ctl.c
-@@ -349,7 +349,6 @@ struct cea_channel_speaker_allocation {
- #define FRW SNDRV_CHMAP_FRW
- #define TC SNDRV_CHMAP_TC
- #define FCH SNDRV_CHMAP_TFC
--#define NA SNDRV_CHMAP_NA
-
- /*
- * CEA-861 channel maps
-@@ -357,69 +356,69 @@ struct cea_channel_speaker_allocation {
- * Stolen from sound/pci/hda/patch_hdmi.c
- * (unlike the source, this uses SNDRV_* constants directly, as by the
- * map_tables array in patch_hdmi.c)
-- * Entries which do not have a physical output channel use 0. Entries which
-- * require userspace to output silence use NA (SNDRV_CHMAP_NA).
-+ * Unknown entries use 0, which unfortunately is SNDRV_CHMAP_UNKNOWN instead
-+ * of SNDRV_CHMAP_NA.
- */
- static struct cea_channel_speaker_allocation channel_allocations[] = {
- /* channel: 7 6 5 4 3 2 1 0 */
- { .ca_index = 0x00, .speakers = { 0, 0, 0, 0, 0, 0, FR, FL } },
- /* 2.1 */
--{ .ca_index = 0x01, .speakers = { 0, 0, 0, 0, NA, LFE, FR, FL } },
-+{ .ca_index = 0x01, .speakers = { 0, 0, 0, 0, 0, LFE, FR, FL } },
- /* Dolby Surround */
--{ .ca_index = 0x02, .speakers = { 0, 0, 0, 0, FC, NA, FR, FL } },
-+{ .ca_index = 0x02, .speakers = { 0, 0, 0, 0, FC, 0, FR, FL } },
- /* surround40 */
--{ .ca_index = 0x08, .speakers = { NA, NA, RR, RL, NA, NA, FR, FL } },
-+{ .ca_index = 0x08, .speakers = { 0, 0, RR, RL, 0, 0, FR, FL } },
- /* surround41 */
--{ .ca_index = 0x09, .speakers = { NA, NA, RR, RL, NA, LFE, FR, FL } },
-+{ .ca_index = 0x09, .speakers = { 0, 0, RR, RL, 0, LFE, FR, FL } },
- /* surround50 */
--{ .ca_index = 0x0a, .speakers = { NA, NA, RR, RL, FC, NA, FR, FL } },
-+{ .ca_index = 0x0a, .speakers = { 0, 0, RR, RL, FC, 0, FR, FL } },
- /* surround51 */
--{ .ca_index = 0x0b, .speakers = { NA, NA, RR, RL, FC, LFE, FR, FL } },
-+{ .ca_index = 0x0b, .speakers = { 0, 0, RR, RL, FC, LFE, FR, FL } },
- /* 6.1 */
--{ .ca_index = 0x0f, .speakers = { NA, RC, RR, RL, FC, LFE, FR, FL } },
-+{ .ca_index = 0x0f, .speakers = { 0, RC, RR, RL, FC, LFE, FR, FL } },
- /* surround71 */
- { .ca_index = 0x13, .speakers = { RRC, RLC, RR, RL, FC, LFE, FR, FL } },
-
--{ .ca_index = 0x03, .speakers = { NA, NA, NA, NA, FC, LFE, FR, FL } },
--{ .ca_index = 0x04, .speakers = { NA, NA, NA, RC, NA, NA, FR, FL } },
--{ .ca_index = 0x05, .speakers = { NA, NA, NA, RC, NA, LFE, FR, FL } },
--{ .ca_index = 0x06, .speakers = { NA, NA, NA, RC, FC, NA, FR, FL } },
--{ .ca_index = 0x07, .speakers = { NA, NA, NA, RC, FC, LFE, FR, FL } },
--{ .ca_index = 0x0c, .speakers = { NA, RC, RR, RL, NA, NA, FR, FL } },
--{ .ca_index = 0x0d, .speakers = { NA, RC, RR, RL, NA, LFE, FR, FL } },
--{ .ca_index = 0x0e, .speakers = { NA, RC, RR, RL, FC, NA, FR, FL } },
--{ .ca_index = 0x10, .speakers = { RRC, RLC, RR, RL, NA, NA, FR, FL } },
--{ .ca_index = 0x11, .speakers = { RRC, RLC, RR, RL, NA, LFE, FR, FL } },
--{ .ca_index = 0x12, .speakers = { RRC, RLC, RR, RL, FC, NA, FR, FL } },
--{ .ca_index = 0x14, .speakers = { FRC, FLC, NA, NA, NA, NA, FR, FL } },
--{ .ca_index = 0x15, .speakers = { FRC, FLC, NA, NA, NA, LFE, FR, FL } },
--{ .ca_index = 0x16, .speakers = { FRC, FLC, NA, NA, FC, NA, FR, FL } },
--{ .ca_index = 0x17, .speakers = { FRC, FLC, NA, NA, FC, LFE, FR, FL } },
--{ .ca_index = 0x18, .speakers = { FRC, FLC, NA, RC, NA, NA, FR, FL } },
--{ .ca_index = 0x19, .speakers = { FRC, FLC, NA, RC, NA, LFE, FR, FL } },
--{ .ca_index = 0x1a, .speakers = { FRC, FLC, NA, RC, FC, NA, FR, FL } },
--{ .ca_index = 0x1b, .speakers = { FRC, FLC, NA, RC, FC, LFE, FR, FL } },
--{ .ca_index = 0x1c, .speakers = { FRC, FLC, RR, RL, NA, NA, FR, FL } },
--{ .ca_index = 0x1d, .speakers = { FRC, FLC, RR, RL, NA, LFE, FR, FL } },
--{ .ca_index = 0x1e, .speakers = { FRC, FLC, RR, RL, FC, NA, FR, FL } },
-+{ .ca_index = 0x03, .speakers = { 0, 0, 0, 0, FC, LFE, FR, FL } },
-+{ .ca_index = 0x04, .speakers = { 0, 0, 0, RC, 0, 0, FR, FL } },
-+{ .ca_index = 0x05, .speakers = { 0, 0, 0, RC, 0, LFE, FR, FL } },
-+{ .ca_index = 0x06, .speakers = { 0, 0, 0, RC, FC, 0, FR, FL } },
-+{ .ca_index = 0x07, .speakers = { 0, 0, 0, RC, FC, LFE, FR, FL } },
-+{ .ca_index = 0x0c, .speakers = { 0, RC, RR, RL, 0, 0, FR, FL } },
-+{ .ca_index = 0x0d, .speakers = { 0, RC, RR, RL, 0, LFE, FR, FL } },
-+{ .ca_index = 0x0e, .speakers = { 0, RC, RR, RL, FC, 0, FR, FL } },
-+{ .ca_index = 0x10, .speakers = { RRC, RLC, RR, RL, 0, 0, FR, FL } },
-+{ .ca_index = 0x11, .speakers = { RRC, RLC, RR, RL, 0, LFE, FR, FL } },
-+{ .ca_index = 0x12, .speakers = { RRC, RLC, RR, RL, FC, 0, FR, FL } },
-+{ .ca_index = 0x14, .speakers = { FRC, FLC, 0, 0, 0, 0, FR, FL } },
-+{ .ca_index = 0x15, .speakers = { FRC, FLC, 0, 0, 0, LFE, FR, FL } },
-+{ .ca_index = 0x16, .speakers = { FRC, FLC, 0, 0, FC, 0, FR, FL } },
-+{ .ca_index = 0x17, .speakers = { FRC, FLC, 0, 0, FC, LFE, FR, FL } },
-+{ .ca_index = 0x18, .speakers = { FRC, FLC, 0, RC, 0, 0, FR, FL } },
-+{ .ca_index = 0x19, .speakers = { FRC, FLC, 0, RC, 0, LFE, FR, FL } },
-+{ .ca_index = 0x1a, .speakers = { FRC, FLC, 0, RC, FC, 0, FR, FL } },
-+{ .ca_index = 0x1b, .speakers = { FRC, FLC, 0, RC, FC, LFE, FR, FL } },
-+{ .ca_index = 0x1c, .speakers = { FRC, FLC, RR, RL, 0, 0, FR, FL } },
-+{ .ca_index = 0x1d, .speakers = { FRC, FLC, RR, RL, 0, LFE, FR, FL } },
-+{ .ca_index = 0x1e, .speakers = { FRC, FLC, RR, RL, FC, 0, FR, FL } },
- { .ca_index = 0x1f, .speakers = { FRC, FLC, RR, RL, FC, LFE, FR, FL } },
--{ .ca_index = 0x20, .speakers = { NA, FCH, RR, RL, FC, NA, FR, FL } },
--{ .ca_index = 0x21, .speakers = { NA, FCH, RR, RL, FC, LFE, FR, FL } },
--{ .ca_index = 0x22, .speakers = { TC, NA, RR, RL, FC, NA, FR, FL } },
--{ .ca_index = 0x23, .speakers = { TC, NA, RR, RL, FC, LFE, FR, FL } },
--{ .ca_index = 0x24, .speakers = { FRH, FLH, RR, RL, NA, NA, FR, FL } },
--{ .ca_index = 0x25, .speakers = { FRH, FLH, RR, RL, NA, LFE, FR, FL } },
--{ .ca_index = 0x26, .speakers = { FRW, FLW, RR, RL, NA, NA, FR, FL } },
--{ .ca_index = 0x27, .speakers = { FRW, FLW, RR, RL, NA, LFE, FR, FL } },
--{ .ca_index = 0x28, .speakers = { TC, RC, RR, RL, FC, NA, FR, FL } },
-+{ .ca_index = 0x20, .speakers = { 0, FCH, RR, RL, FC, 0, FR, FL } },
-+{ .ca_index = 0x21, .speakers = { 0, FCH, RR, RL, FC, LFE, FR, FL } },
-+{ .ca_index = 0x22, .speakers = { TC, 0, RR, RL, FC, 0, FR, FL } },
-+{ .ca_index = 0x23, .speakers = { TC, 0, RR, RL, FC, LFE, FR, FL } },
-+{ .ca_index = 0x24, .speakers = { FRH, FLH, RR, RL, 0, 0, FR, FL } },
-+{ .ca_index = 0x25, .speakers = { FRH, FLH, RR, RL, 0, LFE, FR, FL } },
-+{ .ca_index = 0x26, .speakers = { FRW, FLW, RR, RL, 0, 0, FR, FL } },
-+{ .ca_index = 0x27, .speakers = { FRW, FLW, RR, RL, 0, LFE, FR, FL } },
-+{ .ca_index = 0x28, .speakers = { TC, RC, RR, RL, FC, 0, FR, FL } },
- { .ca_index = 0x29, .speakers = { TC, RC, RR, RL, FC, LFE, FR, FL } },
--{ .ca_index = 0x2a, .speakers = { FCH, RC, RR, RL, FC, NA, FR, FL } },
-+{ .ca_index = 0x2a, .speakers = { FCH, RC, RR, RL, FC, 0, FR, FL } },
- { .ca_index = 0x2b, .speakers = { FCH, RC, RR, RL, FC, LFE, FR, FL } },
--{ .ca_index = 0x2c, .speakers = { TC, FCH, RR, RL, FC, NA, FR, FL } },
-+{ .ca_index = 0x2c, .speakers = { TC, FCH, RR, RL, FC, 0, FR, FL } },
- { .ca_index = 0x2d, .speakers = { TC, FCH, RR, RL, FC, LFE, FR, FL } },
--{ .ca_index = 0x2e, .speakers = { FRH, FLH, RR, RL, FC, NA, FR, FL } },
-+{ .ca_index = 0x2e, .speakers = { FRH, FLH, RR, RL, FC, 0, FR, FL } },
- { .ca_index = 0x2f, .speakers = { FRH, FLH, RR, RL, FC, LFE, FR, FL } },
--{ .ca_index = 0x30, .speakers = { FRW, FLW, RR, RL, FC, NA, FR, FL } },
-+{ .ca_index = 0x30, .speakers = { FRW, FLW, RR, RL, FC, 0, FR, FL } },
- { .ca_index = 0x31, .speakers = { FRW, FLW, RR, RL, FC, LFE, FR, FL } },
- };
-
diff --git a/target/linux/brcm2708/patches-4.4/0315-Revert-bcm2835-implement-channel-map-API.patch b/target/linux/brcm2708/patches-4.4/0315-Revert-bcm2835-implement-channel-map-API.patch
deleted file mode 100644
index 142ac24..0000000
--- a/target/linux/brcm2708/patches-4.4/0315-Revert-bcm2835-implement-channel-map-API.patch
+++ /dev/null
@@ -1,496 +0,0 @@
-From af788c8cdfc0b6179ca378edab1bf80bf86b85be Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Fri, 29 Apr 2016 17:29:03 +0100
-Subject: [PATCH] Revert "bcm2835: implement channel map API"
-
-This reverts commit 5efba3f8c180c39609a8d40033ef92046ef0de75.
----
- sound/arm/bcm2835-ctl.c | 299 ----------------------------------------------
- sound/arm/bcm2835-pcm.c | 69 ++---------
- sound/arm/bcm2835-vchiq.c | 13 --
- sound/arm/bcm2835.h | 4 -
- 4 files changed, 7 insertions(+), 378 deletions(-)
-
---- a/sound/arm/bcm2835-ctl.c
-+++ b/sound/arm/bcm2835-ctl.c
-@@ -327,304 +327,6 @@ static struct snd_kcontrol_new snd_bcm28
- },
- };
-
--struct cea_channel_speaker_allocation {
-- int ca_index;
-- int speakers[8];
--};
--
--#define FL SNDRV_CHMAP_FL
--#define FR SNDRV_CHMAP_FR
--#define RL SNDRV_CHMAP_RL
--#define RR SNDRV_CHMAP_RR
--#define LFE SNDRV_CHMAP_LFE
--#define FC SNDRV_CHMAP_FC
--#define RLC SNDRV_CHMAP_RLC
--#define RRC SNDRV_CHMAP_RRC
--#define RC SNDRV_CHMAP_RC
--#define FLC SNDRV_CHMAP_FLC
--#define FRC SNDRV_CHMAP_FRC
--#define FLH SNDRV_CHMAP_TFL
--#define FRH SNDRV_CHMAP_TFR
--#define FLW SNDRV_CHMAP_FLW
--#define FRW SNDRV_CHMAP_FRW
--#define TC SNDRV_CHMAP_TC
--#define FCH SNDRV_CHMAP_TFC
--
--/*
-- * CEA-861 channel maps
-- *
-- * Stolen from sound/pci/hda/patch_hdmi.c
-- * (unlike the source, this uses SNDRV_* constants directly, as by the
-- * map_tables array in patch_hdmi.c)
-- * Unknown entries use 0, which unfortunately is SNDRV_CHMAP_UNKNOWN instead
-- * of SNDRV_CHMAP_NA.
-- */
--static struct cea_channel_speaker_allocation channel_allocations[] = {
--/* channel: 7 6 5 4 3 2 1 0 */
--{ .ca_index = 0x00, .speakers = { 0, 0, 0, 0, 0, 0, FR, FL } },
-- /* 2.1 */
--{ .ca_index = 0x01, .speakers = { 0, 0, 0, 0, 0, LFE, FR, FL } },
-- /* Dolby Surround */
--{ .ca_index = 0x02, .speakers = { 0, 0, 0, 0, FC, 0, FR, FL } },
-- /* surround40 */
--{ .ca_index = 0x08, .speakers = { 0, 0, RR, RL, 0, 0, FR, FL } },
-- /* surround41 */
--{ .ca_index = 0x09, .speakers = { 0, 0, RR, RL, 0, LFE, FR, FL } },
-- /* surround50 */
--{ .ca_index = 0x0a, .speakers = { 0, 0, RR, RL, FC, 0, FR, FL } },
-- /* surround51 */
--{ .ca_index = 0x0b, .speakers = { 0, 0, RR, RL, FC, LFE, FR, FL } },
-- /* 6.1 */
--{ .ca_index = 0x0f, .speakers = { 0, RC, RR, RL, FC, LFE, FR, FL } },
-- /* surround71 */
--{ .ca_index = 0x13, .speakers = { RRC, RLC, RR, RL, FC, LFE, FR, FL } },
--
--{ .ca_index = 0x03, .speakers = { 0, 0, 0, 0, FC, LFE, FR, FL } },
--{ .ca_index = 0x04, .speakers = { 0, 0, 0, RC, 0, 0, FR, FL } },
--{ .ca_index = 0x05, .speakers = { 0, 0, 0, RC, 0, LFE, FR, FL } },
--{ .ca_index = 0x06, .speakers = { 0, 0, 0, RC, FC, 0, FR, FL } },
--{ .ca_index = 0x07, .speakers = { 0, 0, 0, RC, FC, LFE, FR, FL } },
--{ .ca_index = 0x0c, .speakers = { 0, RC, RR, RL, 0, 0, FR, FL } },
--{ .ca_index = 0x0d, .speakers = { 0, RC, RR, RL, 0, LFE, FR, FL } },
--{ .ca_index = 0x0e, .speakers = { 0, RC, RR, RL, FC, 0, FR, FL } },
--{ .ca_index = 0x10, .speakers = { RRC, RLC, RR, RL, 0, 0, FR, FL } },
--{ .ca_index = 0x11, .speakers = { RRC, RLC, RR, RL, 0, LFE, FR, FL } },
--{ .ca_index = 0x12, .speakers = { RRC, RLC, RR, RL, FC, 0, FR, FL } },
--{ .ca_index = 0x14, .speakers = { FRC, FLC, 0, 0, 0, 0, FR, FL } },
--{ .ca_index = 0x15, .speakers = { FRC, FLC, 0, 0, 0, LFE, FR, FL } },
--{ .ca_index = 0x16, .speakers = { FRC, FLC, 0, 0, FC, 0, FR, FL } },
--{ .ca_index = 0x17, .speakers = { FRC, FLC, 0, 0, FC, LFE, FR, FL } },
--{ .ca_index = 0x18, .speakers = { FRC, FLC, 0, RC, 0, 0, FR, FL } },
--{ .ca_index = 0x19, .speakers = { FRC, FLC, 0, RC, 0, LFE, FR, FL } },
--{ .ca_index = 0x1a, .speakers = { FRC, FLC, 0, RC, FC, 0, FR, FL } },
--{ .ca_index = 0x1b, .speakers = { FRC, FLC, 0, RC, FC, LFE, FR, FL } },
--{ .ca_index = 0x1c, .speakers = { FRC, FLC, RR, RL, 0, 0, FR, FL } },
--{ .ca_index = 0x1d, .speakers = { FRC, FLC, RR, RL, 0, LFE, FR, FL } },
--{ .ca_index = 0x1e, .speakers = { FRC, FLC, RR, RL, FC, 0, FR, FL } },
--{ .ca_index = 0x1f, .speakers = { FRC, FLC, RR, RL, FC, LFE, FR, FL } },
--{ .ca_index = 0x20, .speakers = { 0, FCH, RR, RL, FC, 0, FR, FL } },
--{ .ca_index = 0x21, .speakers = { 0, FCH, RR, RL, FC, LFE, FR, FL } },
--{ .ca_index = 0x22, .speakers = { TC, 0, RR, RL, FC, 0, FR, FL } },
--{ .ca_index = 0x23, .speakers = { TC, 0, RR, RL, FC, LFE, FR, FL } },
--{ .ca_index = 0x24, .speakers = { FRH, FLH, RR, RL, 0, 0, FR, FL } },
--{ .ca_index = 0x25, .speakers = { FRH, FLH, RR, RL, 0, LFE, FR, FL } },
--{ .ca_index = 0x26, .speakers = { FRW, FLW, RR, RL, 0, 0, FR, FL } },
--{ .ca_index = 0x27, .speakers = { FRW, FLW, RR, RL, 0, LFE, FR, FL } },
--{ .ca_index = 0x28, .speakers = { TC, RC, RR, RL, FC, 0, FR, FL } },
--{ .ca_index = 0x29, .speakers = { TC, RC, RR, RL, FC, LFE, FR, FL } },
--{ .ca_index = 0x2a, .speakers = { FCH, RC, RR, RL, FC, 0, FR, FL } },
--{ .ca_index = 0x2b, .speakers = { FCH, RC, RR, RL, FC, LFE, FR, FL } },
--{ .ca_index = 0x2c, .speakers = { TC, FCH, RR, RL, FC, 0, FR, FL } },
--{ .ca_index = 0x2d, .speakers = { TC, FCH, RR, RL, FC, LFE, FR, FL } },
--{ .ca_index = 0x2e, .speakers = { FRH, FLH, RR, RL, FC, 0, FR, FL } },
--{ .ca_index = 0x2f, .speakers = { FRH, FLH, RR, RL, FC, LFE, FR, FL } },
--{ .ca_index = 0x30, .speakers = { FRW, FLW, RR, RL, FC, 0, FR, FL } },
--{ .ca_index = 0x31, .speakers = { FRW, FLW, RR, RL, FC, LFE, FR, FL } },
--};
--
--static int snd_bcm2835_chmap_ctl_tlv(struct snd_kcontrol *kcontrol, int op_flag,
-- unsigned int size, unsigned int __user *tlv)
--{
-- unsigned int __user *dst;
-- int count = 0;
-- int i;
--
-- if (size < 8)
-- return -ENOMEM;
-- if (put_user(SNDRV_CTL_TLVT_CONTAINER, tlv))
-- return -EFAULT;
-- size -= 8;
-- dst = tlv + 2;
-- for (i = 0; i < ARRAY_SIZE(channel_allocations); i++) {
-- struct cea_channel_speaker_allocation *ch = &channel_allocations[i];
-- int num_chs = 0;
-- int chs_bytes;
-- int c;
--
-- for (c = 0; c < 8; c++) {
-- if (ch->speakers[c])
-- num_chs++;
-- }
--
-- chs_bytes = num_chs * 4;
-- if (size < 8)
-- return -ENOMEM;
-- if (put_user(SNDRV_CTL_TLVT_CHMAP_FIXED, dst) ||
-- put_user(chs_bytes, dst + 1))
-- return -EFAULT;
-- dst += 2;
-- size -= 8;
-- count += 8;
-- if (size < chs_bytes)
-- return -ENOMEM;
-- size -= chs_bytes;
-- count += chs_bytes;
-- for (c = 0; c < 8; c++) {
-- int sp = ch->speakers[7 - c];
-- if (sp) {
-- if (put_user(sp, dst))
-- return -EFAULT;
-- dst++;
-- }
-- }
-- }
-- if (put_user(count, tlv + 1))
-- return -EFAULT;
-- return 0;
--}
--
--static int snd_bcm2835_chmap_ctl_get(struct snd_kcontrol *kcontrol,
-- struct snd_ctl_elem_value *ucontrol)
--{
-- struct snd_pcm_chmap *info = snd_kcontrol_chip(kcontrol);
-- bcm2835_chip_t *chip = info->private_data;
-- unsigned int idx = snd_ctl_get_ioffidx(kcontrol, &ucontrol->id);
-- struct snd_pcm_substream *substream = snd_pcm_chmap_substream(info, idx);
-- struct cea_channel_speaker_allocation *ch = NULL;
-- int res = 0;
-- int cur = 0;
-- int i;
--
-- if (mutex_lock_interruptible(&chip->audio_mutex))
-- return -EINTR;
--
-- if (!substream || !substream->runtime) {
-- res = -ENODEV;
-- goto unlock;
-- }
--
-- for (i = 0; i < ARRAY_SIZE(channel_allocations); i++) {
-- if (channel_allocations[i].ca_index == chip->cea_chmap)
-- ch = &channel_allocations[i];
-- }
--
-- /* If no layout was set yet, return a dummy. Apparently the userspace
-- * API will be confused if we don't. */
-- if (!ch)
-- ch = &channel_allocations[0];
--
-- for (i = 0; i < 8; i++) {
-- if (ch->speakers[7 - i])
-- ucontrol->value.integer.value[cur++] = ch->speakers[7 - i];
-- }
-- while (cur < 8)
-- ucontrol->value.integer.value[cur++] = SNDRV_CHMAP_NA;
--
--unlock:
-- mutex_unlock(&chip->audio_mutex);
-- return res;
--}
--
--static int snd_bcm2835_chmap_ctl_put(struct snd_kcontrol *kcontrol,
-- struct snd_ctl_elem_value *ucontrol)
--{
-- struct snd_pcm_chmap *info = snd_kcontrol_chip(kcontrol);
-- bcm2835_chip_t *chip = info->private_data;
-- unsigned int idx = snd_ctl_get_ioffidx(kcontrol, &ucontrol->id);
-- struct snd_pcm_substream *substream = snd_pcm_chmap_substream(info, idx);
-- int i, prepared = 0, cea_chmap = -1;
-- int res = 0;
-- int remap[8];
--
-- if (mutex_lock_interruptible(&chip->audio_mutex))
-- return -EINTR;
--
-- if (!substream || !substream->runtime) {
-- res = -ENODEV;
-- goto unlock;
-- }
--
-- switch (substream->runtime->status->state) {
-- case SNDRV_PCM_STATE_OPEN:
-- case SNDRV_PCM_STATE_SETUP:
-- break;
-- case SNDRV_PCM_STATE_PREPARED:
-- prepared = 1;
-- break;
-- default:
-- res = -EBUSY;
-- goto unlock;
-- }
--
-- for (i = 0; i < ARRAY_SIZE(channel_allocations); i++) {
-- struct cea_channel_speaker_allocation *ch = &channel_allocations[i];
-- int matches = 1;
-- int cur = 0;
-- int x;
-- memset(remap, 0, sizeof(remap));
-- for (x = 0; x < substream->runtime->channels; x++) {
-- int sp = ucontrol->value.integer.value[x];
-- while (cur < 8 && !ch->speakers[7 - cur])
-- cur++;
-- if (cur >= 8) {
-- /* user has more channels than ch */
-- matches = 0;
-- break;
-- }
-- if (ch->speakers[7 - cur] != sp) {
-- matches = 0;
-- break;
-- }
-- remap[x] = cur;
-- cur++;
-- }
-- for (x = cur; x < 8; x++) {
-- if (ch->speakers[7 - x]) {
-- /* ch has more channels than user */
-- matches = 0;
-- break;
-- }
-- }
-- if (matches) {
-- cea_chmap = ch->ca_index;
-- break;
-- }
-- }
--
-- if (cea_chmap < 0) {
-- res = -EINVAL;
-- goto unlock;
-- }
--
-- /* don't change the layout if another substream is active */
-- if (chip->opened != (1 << substream->number) && chip->cea_chmap != cea_chmap) {
-- res = -EBUSY; /* unsure whether this is a good error code */
-- goto unlock;
-- }
--
-- chip->cea_chmap = cea_chmap;
-- for (i = 0; i < 8; i++)
-- chip->map_channels[i] = remap[i];
-- if (prepared)
-- snd_bcm2835_pcm_prepare_again(substream);
--
--unlock:
-- mutex_unlock(&chip->audio_mutex);
-- return res;
--}
--
--static int snd_bcm2835_add_chmap_ctl(bcm2835_chip_t * chip)
--{
-- struct snd_pcm_chmap *chmap;
-- struct snd_kcontrol *kctl;
-- int err, i;
--
-- err = snd_pcm_add_chmap_ctls(chip->pcm,
-- SNDRV_PCM_STREAM_PLAYBACK,
-- NULL, 8, 0, &chmap);
-- if (err < 0)
-- return err;
-- /* override handlers */
-- chmap->private_data = chip;
-- kctl = chmap->kctl;
-- for (i = 0; i < kctl->count; i++)
-- kctl->vd[i].access |= SNDRV_CTL_ELEM_ACCESS_WRITE;
-- kctl->get = snd_bcm2835_chmap_ctl_get;
-- kctl->put = snd_bcm2835_chmap_ctl_put;
-- kctl->tlv.c = snd_bcm2835_chmap_ctl_tlv;
-- return 0;
--}
--
- int snd_bcm2835_new_ctl(bcm2835_chip_t * chip)
- {
- int err;
-@@ -638,7 +340,6 @@ int snd_bcm2835_new_ctl(bcm2835_chip_t *
- if (err < 0)
- return err;
- }
-- snd_bcm2835_add_chmap_ctl(chip);
- for (idx = 0; idx < ARRAY_SIZE(snd_bcm2835_spdif); idx++) {
- err = snd_ctl_add(chip->card,
- snd_ctl_new1(&snd_bcm2835_spdif[idx], chip));
---- a/sound/arm/bcm2835-pcm.c
-+++ b/sound/arm/bcm2835-pcm.c
-@@ -19,9 +19,6 @@
-
- #include "bcm2835.h"
-
--/* The hardware can not do much more num_channels*samplerate then this value */
--#define MAX_COMBINED_RATE 768000
--
- /* hardware definition */
- static struct snd_pcm_hardware snd_bcm2835_playback_hw = {
- .info = (SNDRV_PCM_INFO_INTERLEAVED | SNDRV_PCM_INFO_BLOCK_TRANSFER |
-@@ -110,31 +107,6 @@ static irqreturn_t bcm2835_playback_fifo
- return IRQ_HANDLED;
- }
-
--
--static int rate_hw_constraint_rate(struct snd_pcm_hw_params *params,
-- struct snd_pcm_hw_rule *rule)
--{
-- struct snd_interval *channels = hw_param_interval(params, SNDRV_PCM_HW_PARAM_CHANNELS);
-- struct snd_interval rates = {
-- .min = 8000,
-- .max = min(192000u, MAX_COMBINED_RATE / max(channels->min, 1u)),
-- };
-- struct snd_interval *rate = hw_param_interval(params, SNDRV_PCM_HW_PARAM_RATE);
-- return snd_interval_refine(rate, &rates);
--}
--
--static int rate_hw_constraint_channels(struct snd_pcm_hw_params *params,
-- struct snd_pcm_hw_rule *rule)
--{
-- struct snd_interval *rate = hw_param_interval(params, SNDRV_PCM_HW_PARAM_RATE);
-- struct snd_interval channels_interval = {
-- .min = 1,
-- .max = min(8u, MAX_COMBINED_RATE / max(rate->min, 1u)),
-- };
-- struct snd_interval *channels = hw_param_interval(params, SNDRV_PCM_HW_PARAM_CHANNELS);
-- return snd_interval_refine(channels, &channels_interval);
--}
--
- /* open callback */
- static int snd_bcm2835_playback_open_generic(
- struct snd_pcm_substream *substream, int spdif)
-@@ -216,24 +188,8 @@ static int snd_bcm2835_playback_open_gen
- snd_pcm_hw_constraint_step(runtime, 0, SNDRV_PCM_HW_PARAM_PERIOD_BYTES,
- 16);
-
-- /* When playing PCM, pretend that we support the full range of channels
-- * and sample rates. The GPU can't output it, but is able to resample
-- * the data to a rate the hardware can handle it. This won't work with
-- * compressed data; the resampler would just destroy it. */
-- if (spdif) {
-- err = snd_pcm_hw_rule_add(runtime, 0, SNDRV_PCM_HW_PARAM_RATE,
-- rate_hw_constraint_rate, NULL,
-- SNDRV_PCM_HW_PARAM_CHANNELS, -1);
-- err = snd_pcm_hw_rule_add(runtime, 0, SNDRV_PCM_HW_PARAM_CHANNELS,
-- rate_hw_constraint_channels, NULL,
-- SNDRV_PCM_HW_PARAM_RATE, -1);
-- }
--
- chip->alsa_stream[idx] = alsa_stream;
-
-- if (!chip->opened)
-- chip->cea_chmap = -1;
--
- chip->opened |= (1 << idx);
- alsa_stream->open = 1;
- alsa_stream->draining = 1;
-@@ -344,7 +300,8 @@ static int snd_bcm2835_pcm_hw_free(struc
- return snd_pcm_lib_free_pages(substream);
- }
-
--int snd_bcm2835_pcm_prepare_again(struct snd_pcm_substream *substream)
-+/* prepare callback */
-+static int snd_bcm2835_pcm_prepare(struct snd_pcm_substream *substream)
- {
- bcm2835_chip_t *chip = snd_pcm_substream_chip(substream);
- struct snd_pcm_runtime *runtime = substream->runtime;
-@@ -352,6 +309,11 @@ int snd_bcm2835_pcm_prepare_again(struct
- int channels;
- int err;
-
-+ audio_info(" .. IN\n");
-+
-+ if (mutex_lock_interruptible(&chip->audio_mutex))
-+ return -EINTR;
-+
- /* notify the vchiq that it should enter spdif passthrough mode by
- * setting channels=0 (see
- * https://github.com/raspberrypi/linux/issues/528) */
-@@ -367,23 +329,6 @@ int snd_bcm2835_pcm_prepare_again(struct
- audio_error(" error setting hw params\n");
- }
-
-- return err;
--}
--
--/* prepare callback */
--static int snd_bcm2835_pcm_prepare(struct snd_pcm_substream *substream)
--{
-- bcm2835_chip_t *chip = snd_pcm_substream_chip(substream);
-- struct snd_pcm_runtime *runtime = substream->runtime;
-- bcm2835_alsa_stream_t *alsa_stream = runtime->private_data;
--
-- audio_info(" .. IN\n");
--
-- if (mutex_lock_interruptible(&chip->audio_mutex))
-- return -EINTR;
--
-- snd_bcm2835_pcm_prepare_again(substream);
--
- bcm2835_audio_setup(alsa_stream);
-
- /* in preparation of the stream, set the controls (volume level) of the stream */
---- a/sound/arm/bcm2835-vchiq.c
-+++ b/sound/arm/bcm2835-vchiq.c
-@@ -570,8 +570,6 @@ int bcm2835_audio_set_params(bcm2835_als
- VC_AUDIO_MSG_T m;
- AUDIO_INSTANCE_T *instance = alsa_stream->instance;
- int32_t success;
-- uint32_t chmap_value;
-- int i;
- int ret;
- LOG_DBG(" .. IN\n");
-
-@@ -595,21 +593,10 @@ int bcm2835_audio_set_params(bcm2835_als
-
- instance->result = -1;
-
-- if (alsa_stream->chip->cea_chmap >= 0) {
-- chmap_value = (unsigned)alsa_stream->chip->cea_chmap << 24;
-- } else {
-- chmap_value = 0; /* force stereo */
-- for (i = 0; i < 8; i++)
-- alsa_stream->chip->map_channels[i] = i;
-- }
-- for (i = 0; i < 8; i++)
-- chmap_value |= alsa_stream->chip->map_channels[i] << (i * 3);
--
- m.type = VC_AUDIO_MSG_TYPE_CONFIG;
- m.u.config.channels = channels;
- m.u.config.samplerate = samplerate;
- m.u.config.bps = bps;
-- m.u.config.channelmap = chmap_value;
-
- /* Create the message available completion */
- init_completion(&instance->msg_avail_comp);
---- a/sound/arm/bcm2835.h
-+++ b/sound/arm/bcm2835.h
-@@ -107,8 +107,6 @@ typedef struct bcm2835_chip {
- int old_volume; /* stores the volume value whist muted */
- int dest;
- int mute;
-- int cea_chmap; /* currently requested Audio InfoFrame Data Byte 4 */
-- int map_channels[8];
-
- unsigned int opened;
- unsigned int spdif_status;
-@@ -151,8 +149,6 @@ int snd_bcm2835_new_ctl(bcm2835_chip_t *
- int snd_bcm2835_new_pcm(bcm2835_chip_t * chip);
- int snd_bcm2835_new_spdif_pcm(bcm2835_chip_t * chip);
-
--int snd_bcm2835_pcm_prepare_again(struct snd_pcm_substream *substream);
--
- int bcm2835_audio_open(bcm2835_alsa_stream_t * alsa_stream);
- int bcm2835_audio_close(bcm2835_alsa_stream_t * alsa_stream);
- int bcm2835_audio_set_params(bcm2835_alsa_stream_t * alsa_stream,
diff --git a/target/linux/brcm2708/patches-4.4/0316-Revert-bcm2835-extend-allowed-range-of-channels-and-.patch b/target/linux/brcm2708/patches-4.4/0316-Revert-bcm2835-extend-allowed-range-of-channels-and-.patch
deleted file mode 100644
index b6c97b0..0000000
--- a/target/linux/brcm2708/patches-4.4/0316-Revert-bcm2835-extend-allowed-range-of-channels-and-.patch
+++ /dev/null
@@ -1,37 +0,0 @@
-From 7b159fc86bb5c1c4baf6fdb50c0afd0a23e683e7 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Fri, 29 Apr 2016 17:30:00 +0100
-Subject: [PATCH] Revert "bcm2835: extend allowed range of channels and
- samplerates"
-
-This reverts commit 688a5f0daa45e0a51b324707768d472e1d715c13.
----
- sound/arm/bcm2835-pcm.c | 8 ++++----
- 1 file changed, 4 insertions(+), 4 deletions(-)
-
---- a/sound/arm/bcm2835-pcm.c
-+++ b/sound/arm/bcm2835-pcm.c
-@@ -26,9 +26,9 @@ static struct snd_pcm_hardware snd_bcm28
- .formats = SNDRV_PCM_FMTBIT_U8 | SNDRV_PCM_FMTBIT_S16_LE,
- .rates = SNDRV_PCM_RATE_CONTINUOUS | SNDRV_PCM_RATE_8000_48000,
- .rate_min = 8000,
-- .rate_max = 192000,
-+ .rate_max = 48000,
- .channels_min = 1,
-- .channels_max = 8,
-+ .channels_max = 2,
- .buffer_bytes_max = 128 * 1024,
- .period_bytes_min = 1 * 1024,
- .period_bytes_max = 128 * 1024,
-@@ -43,9 +43,9 @@ static struct snd_pcm_hardware snd_bcm28
- .rates = SNDRV_PCM_RATE_CONTINUOUS | SNDRV_PCM_RATE_44100 |
- SNDRV_PCM_RATE_48000,
- .rate_min = 44100,
-- .rate_max = 192000,
-+ .rate_max = 48000,
- .channels_min = 2,
-- .channels_max = 8,
-+ .channels_max = 2,
- .buffer_bytes_max = 128 * 1024,
- .period_bytes_min = 1 * 1024,
- .period_bytes_max = 128 * 1024,
diff --git a/target/linux/brcm2708/patches-4.4/0317-pinctrl-bcm2835-Return-pins-to-inputs-when-freed.patch b/target/linux/brcm2708/patches-4.4/0317-pinctrl-bcm2835-Return-pins-to-inputs-when-freed.patch
deleted file mode 100644
index 97aa072..0000000
--- a/target/linux/brcm2708/patches-4.4/0317-pinctrl-bcm2835-Return-pins-to-inputs-when-freed.patch
+++ /dev/null
@@ -1,40 +0,0 @@
-From 6e63fd304b56de44e2cd2b10450c95660af6d8c2 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 6 May 2016 12:32:47 +0100
-Subject: [PATCH] pinctrl-bcm2835: Return pins to inputs when freed
-
-When dynamically unloading overlays, it is important that freed pins are
-restored to being inputs to prevent functions from being enabled in
-multiple places at once.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- drivers/pinctrl/bcm/pinctrl-bcm2835.c | 10 ++++++++++
- 1 file changed, 10 insertions(+)
-
---- a/drivers/pinctrl/bcm/pinctrl-bcm2835.c
-+++ b/drivers/pinctrl/bcm/pinctrl-bcm2835.c
-@@ -831,6 +831,15 @@ static const struct pinctrl_ops bcm2835_
- .dt_free_map = bcm2835_pctl_dt_free_map,
- };
-
-+static void bcm2835_pmx_free(struct pinctrl_dev *pctldev,
-+ unsigned offset)
-+{
-+ struct bcm2835_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev);
-+
-+ /* disable by setting to GPIO_IN */
-+ bcm2835_pinctrl_fsel_set(pc, offset, BCM2835_FSEL_GPIO_IN);
-+}
-+
- static int bcm2835_pmx_get_functions_count(struct pinctrl_dev *pctldev)
- {
- return BCM2835_FSEL_COUNT;
-@@ -890,6 +899,7 @@ static int bcm2835_pmx_gpio_set_directio
- }
-
- static const struct pinmux_ops bcm2835_pmx_ops = {
-+ .free = bcm2835_pmx_free,
- .get_functions_count = bcm2835_pmx_get_functions_count,
- .get_function_name = bcm2835_pmx_get_function_name,
- .get_function_groups = bcm2835_pmx_get_function_groups,
diff --git a/target/linux/brcm2708/patches-4.4/0318-BCM270X_DT-i2c0-bcm2708-pin-group-params.patch b/target/linux/brcm2708/patches-4.4/0318-BCM270X_DT-i2c0-bcm2708-pin-group-params.patch
deleted file mode 100644
index 041e1a1..0000000
--- a/target/linux/brcm2708/patches-4.4/0318-BCM270X_DT-i2c0-bcm2708-pin-group-params.patch
+++ /dev/null
@@ -1,99 +0,0 @@
-From 808cc161f7fe7c9b5a906d2e41b58f0dccc96df9 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 6 May 2016 12:53:16 +0100
-Subject: [PATCH] BCM270X_DT: i2c0-bcm2708 - pin group params
-
-Add parameters to set pin groups as a unit, setting the pin function
-appropriately. The parameters are:
- pins_0_1
- pins_28_29
- pins_44_45
- pins_46_47
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/overlays/README | 11 ++++--
- .../arm/boot/dts/overlays/i2c0-bcm2708-overlay.dts | 43 +++++++++++++++++-----
- 2 files changed, 42 insertions(+), 12 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -449,10 +449,15 @@ Params: ds1307 Select t
-
-
- Name: i2c0-bcm2708
--Info: Enable the i2c_bcm2708 driver for the i2c0 bus
-+Info: Enable the i2c_bcm2708 driver for the i2c0 bus. Not all pin combinations
-+ are usable on all platforms.
- Load: dtoverlay=i2c0-bcm2708,<param>=<val>
--Params: sda0_pin GPIO pin for SDA0 (0, 28 [or 44] - default 0)
-- scl0_pin GPIO pin for SCL0 (1, 29 [or 45] - default 1)
-+Params: sda0_pin GPIO pin for SDA0 (deprecated - use pins_*)
-+ scl0_pin GPIO pin for SCL0 (deprecated - use pins_*)
-+ pins_0_1 Use pins 0 and 1 (default)
-+ pins_28_29 Use pins 28 and 29
-+ pins_44_45 Use pins 44 and 45
-+ pins_46_47 Use pins 46 and 47
-
-
- Name: i2c1-bcm2708
---- a/arch/arm/boot/dts/overlays/i2c0-bcm2708-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/i2c0-bcm2708-overlay.dts
-@@ -14,23 +14,48 @@
- fragment at 0 {
- target = <&i2c0>;
- __overlay__ {
-- pinctrl-0 = <&i2c0_pins>;
- status = "okay";
- };
- };
-
- fragment at 1 {
-- target = <&gpio>;
-- __overlay__ {
-- i2c0_pins: i2c0 {
-- brcm,pins = <0 1>;
-- brcm,function = <4>; /* alt0 */
-- };
-+ target = <&i2c0_pins>;
-+ frag1: __overlay__ {
-+ brcm,pins = <0 1>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&i2c0_pins>;
-+ __dormant__ {
-+ brcm,pins = <28 29>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+ };
-+
-+ fragment at 3 {
-+ target = <&i2c0_pins>;
-+ __dormant__ {
-+ brcm,pins = <44 45>;
-+ brcm,function = <5>; /* alt1 */
-+ };
-+ };
-+
-+ fragment at 4 {
-+ target = <&i2c0_pins>;
-+ __dormant__ {
-+ brcm,pins = <46 47>;
-+ brcm,function = <4>; /* alt0 */
- };
- };
-
- __overrides__ {
-- sda0_pin = <&i2c0_pins>,"brcm,pins:0";
-- scl0_pin = <&i2c0_pins>,"brcm,pins:4";
-+ sda0_pin = <&frag1>,"brcm,pins:0";
-+ scl0_pin = <&frag1>,"brcm,pins:4";
-+ pins_0_1 = <0>,"+1-2-3-4";
-+ pins_28_29 = <0>,"-1+2-3-4";
-+ pins_44_45 = <0>,"-1-2+3-4";
-+ pins_46_47 = <0>,"-1-2-3+4";
- };
- };
diff --git a/target/linux/brcm2708/patches-4.4/0319-config-Add-CONFIG_DRM_LOAD_EDID_FIRMWARE.patch b/target/linux/brcm2708/patches-4.4/0319-config-Add-CONFIG_DRM_LOAD_EDID_FIRMWARE.patch
deleted file mode 100644
index eaeaf9e..0000000
--- a/target/linux/brcm2708/patches-4.4/0319-config-Add-CONFIG_DRM_LOAD_EDID_FIRMWARE.patch
+++ /dev/null
@@ -1,30 +0,0 @@
-From db778dfa9420c1bafdede8eacb8c75de03dc35f2 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Fri, 6 May 2016 12:40:37 +0100
-Subject: [PATCH] config: Add CONFIG_DRM_LOAD_EDID_FIRMWARE
-
----
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 2 files changed, 2 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -815,6 +815,7 @@ CONFIG_VIDEO_TW9906=m
- CONFIG_VIDEO_OV7640=m
- CONFIG_VIDEO_MT9V011=m
- CONFIG_DRM=m
-+CONFIG_DRM_LOAD_EDID_FIRMWARE=y
- CONFIG_DRM_UDL=m
- CONFIG_DRM_VC4=m
- CONFIG_FB=y
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -807,6 +807,7 @@ CONFIG_VIDEO_TW9906=m
- CONFIG_VIDEO_OV7640=m
- CONFIG_VIDEO_MT9V011=m
- CONFIG_DRM=m
-+CONFIG_DRM_LOAD_EDID_FIRMWARE=y
- CONFIG_DRM_UDL=m
- CONFIG_DRM_VC4=m
- CONFIG_FB=y
diff --git a/target/linux/brcm2708/patches-4.4/0320-Revert-rpi-update-vc_vchi_audioserv_defs.h.patch b/target/linux/brcm2708/patches-4.4/0320-Revert-rpi-update-vc_vchi_audioserv_defs.h.patch
deleted file mode 100644
index dd58798..0000000
--- a/target/linux/brcm2708/patches-4.4/0320-Revert-rpi-update-vc_vchi_audioserv_defs.h.patch
+++ /dev/null
@@ -1,63 +0,0 @@
-From 7abf3b24c02ba23b73f46c91719729219143ceed Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Fri, 6 May 2016 17:18:57 +0100
-Subject: [PATCH] Revert "rpi: update vc_vchi_audioserv_defs.h"
-
-This reverts commit 64fa9f963dffab0145f7960a593422064bb0aa8d.
----
- sound/arm/vc_vchi_audioserv_defs.h | 13 ++-----------
- 1 file changed, 2 insertions(+), 11 deletions(-)
-
---- a/sound/arm/vc_vchi_audioserv_defs.h
-+++ b/sound/arm/vc_vchi_audioserv_defs.h
-@@ -16,7 +16,7 @@
- #define _VC_AUDIO_DEFS_H_
-
- #define VC_AUDIOSERV_MIN_VER 1
--#define VC_AUDIOSERV_VER 3
-+#define VC_AUDIOSERV_VER 2
-
- // FourCC code used for VCHI connection
- #define VC_AUDIO_SERVER_NAME MAKE_FOURCC("AUDS")
-@@ -36,7 +36,6 @@ typedef enum {
- VC_AUDIO_MSG_TYPE_START, // Configure audio
- VC_AUDIO_MSG_TYPE_STOP, // Configure audio
- VC_AUDIO_MSG_TYPE_WRITE, // Configure audio
-- VC_AUDIO_MSG_TYPE_LATENCY, // request latency in cycles
- VC_AUDIO_MSG_TYPE_MAX
- } VC_AUDIO_MSG_TYPE;
-
-@@ -45,7 +44,6 @@ typedef struct {
- uint32_t channels;
- uint32_t samplerate;
- uint32_t bps;
-- uint32_t channelmap;
-
- } VC_AUDIO_CONFIG_T;
-
-@@ -86,12 +84,6 @@ typedef struct {
- uint16_t max_packet;
- } VC_AUDIO_WRITE_T;
-
--// query latency in samples of sink
--typedef struct
--{
-- uint32_t dummy;
--} VC_AUDIO_LATENCY_T;
--
- // Generic result for a request (VC->HOST)
- typedef struct {
- int32_t success; // Success value
-@@ -116,10 +108,9 @@ typedef struct {
- VC_AUDIO_START_T start;
- VC_AUDIO_STOP_T stop;
- VC_AUDIO_WRITE_T write;
-- VC_AUDIO_LATENCY_T latency;
- VC_AUDIO_RESULT_T result;
- VC_AUDIO_COMPLETE_T complete;
- } u;
- } VC_AUDIO_MSG_T;
-
--#endif // _VC_AUDIO_DEFS_H_
-\ No newline at end of file
-+#endif // _VC_AUDIO_DEFS_H_
diff --git a/target/linux/brcm2708/patches-4.4/0321-Revert-config-Add-CONFIG_DRM_LOAD_EDID_FIRMWARE.patch b/target/linux/brcm2708/patches-4.4/0321-Revert-config-Add-CONFIG_DRM_LOAD_EDID_FIRMWARE.patch
deleted file mode 100644
index 854a68d..0000000
--- a/target/linux/brcm2708/patches-4.4/0321-Revert-config-Add-CONFIG_DRM_LOAD_EDID_FIRMWARE.patch
+++ /dev/null
@@ -1,31 +0,0 @@
-From 6b97b7ea90c13cc0fcfe8c4af96a89f217322680 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Fri, 6 May 2016 17:21:58 +0100
-Subject: [PATCH] Revert "config: Add CONFIG_DRM_LOAD_EDID_FIRMWARE"
-
-This reverts commit 417aed4cb35a479e001c8389fd8d97c3ea612999.
----
- arch/arm/configs/bcm2709_defconfig | 1 -
- arch/arm/configs/bcmrpi_defconfig | 1 -
- 2 files changed, 2 deletions(-)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -815,7 +815,6 @@ CONFIG_VIDEO_TW9906=m
- CONFIG_VIDEO_OV7640=m
- CONFIG_VIDEO_MT9V011=m
- CONFIG_DRM=m
--CONFIG_DRM_LOAD_EDID_FIRMWARE=y
- CONFIG_DRM_UDL=m
- CONFIG_DRM_VC4=m
- CONFIG_FB=y
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -807,7 +807,6 @@ CONFIG_VIDEO_TW9906=m
- CONFIG_VIDEO_OV7640=m
- CONFIG_VIDEO_MT9V011=m
- CONFIG_DRM=m
--CONFIG_DRM_LOAD_EDID_FIRMWARE=y
- CONFIG_DRM_UDL=m
- CONFIG_DRM_VC4=m
- CONFIG_FB=y
diff --git a/target/linux/brcm2708/patches-4.4/0322-ARM-adau1977-adc-Add-basic-machine-driver-for-adau19.patch b/target/linux/brcm2708/patches-4.4/0322-ARM-adau1977-adc-Add-basic-machine-driver-for-adau19.patch
deleted file mode 100644
index d5d8d60..0000000
--- a/target/linux/brcm2708/patches-4.4/0322-ARM-adau1977-adc-Add-basic-machine-driver-for-adau19.patch
+++ /dev/null
@@ -1,285 +0,0 @@
-From 891b971addc0beaa1cc3c0fab7d7ac0f4357ab50 Mon Sep 17 00:00:00 2001
-From: Andrey Grodzovsky <andrey2805 at gmail.com>
-Date: Tue, 3 May 2016 22:10:59 -0400
-Subject: [PATCH] ARM: adau1977-adc: Add basic machine driver for adau1977
- codec driver.
-
-This commit adds basic support for the codec usage including: Device tree overlay,
-binding I2S bus and setting I2S mode, clock source and frequency setting according
-to spec.
-
-Signed-off-by: Andrey Grodzovsky <andrey2805 at gmail.com>
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 7 ++
- .../arm/boot/dts/overlays/adau1977-adc-overlay.dts | 53 +++++++++
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- sound/soc/bcm/Kconfig | 7 ++
- sound/soc/bcm/Makefile | 2 +
- sound/soc/bcm/adau1977-adc.c | 125 +++++++++++++++++++++
- 8 files changed, 197 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/adau1977-adc-overlay.dts
- create mode 100644 sound/soc/bcm/adau1977-adc.c
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -12,6 +12,7 @@ ifeq ($(CONFIG_ARCH_BCM2835),y)
- RPI_DT_OVERLAYS=y
- endif
-
-+dtbo-$(RPI_DT_OVERLAYS) += adau1977-adc.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += ads7846.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += akkordion-iqdacplus.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += at86rf233.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -161,6 +161,13 @@ Params:
- and the other i2c baudrate parameters.
-
-
-+Name: adau1977-adc
-+Info: Overlay for activation of ADAU1977 ADC codec over I2C for control
-+ and I2S for data.
-+Load: dtoverlay=adau1977-adc
-+Params: <None>
-+
-+
- Name: ads7846
- Info: ADS7846 Touch controller
- Load: dtoverlay=ads7846,<param>=<val>
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/adau1977-adc-overlay.dts
-@@ -0,0 +1,53 @@
-+// Definitions for ADAU1977 ADC
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&soc>;
-+
-+ __overlay__ {
-+ codec_supply: fixedregulator at 0 {
-+ compatible = "regulator-fixed";
-+ regulator-name = "AVDD";
-+ regulator-min-microvolt = <3300000>;
-+ regulator-max-microvolt = <3300000>;
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&i2c>;
-+
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ adau1977: codec at 11 {
-+ compatible = "adi,adau1977";
-+ reg = <0x11>;
-+ reset-gpios = <&gpio 5 0>;
-+ AVDD-supply = <&codec_supply>;
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&i2s>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 3 {
-+ target = <&sound>;
-+ __overlay__ {
-+ compatible = "adi,adau1977-adc";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
-+};
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -861,6 +861,7 @@ CONFIG_SND_BCM2708_SOC_BOOMBERRY_DAC=m
- CONFIG_SND_BCM2708_SOC_BOOMBERRY_DIGI=m
- CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC=m
- CONFIG_SND_BCM2708_SOC_RASPIDAC3=m
-+CONFIG_SND_BCM2708_SOC_ADAU1977_ADC=m
- CONFIG_SND_SOC_ADAU1701=m
- CONFIG_SND_SOC_WM8804_I2C=m
- CONFIG_SND_SIMPLE_CARD=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -853,6 +853,7 @@ CONFIG_SND_BCM2708_SOC_BOOMBERRY_DAC=m
- CONFIG_SND_BCM2708_SOC_BOOMBERRY_DIGI=m
- CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC=m
- CONFIG_SND_BCM2708_SOC_RASPIDAC3=m
-+CONFIG_SND_BCM2708_SOC_ADAU1977_ADC=m
- CONFIG_SND_SOC_ADAU1701=m
- CONFIG_SND_SOC_WM8804_I2C=m
- CONFIG_SND_SIMPLE_CARD=m
---- a/sound/soc/bcm/Kconfig
-+++ b/sound/soc/bcm/Kconfig
-@@ -78,3 +78,10 @@ config SND_BCM2708_SOC_RASPIDAC3
- select SND_SOC_TPA6130A2
- help
- Say Y or M if you want to add support for RaspiDAC Rev.3x.
-+
-+config SND_BCM2708_SOC_ADAU1977_ADC
-+ tristate "Support for ADAU1977 ADC"
-+ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
-+ select SND_SOC_ADAU1977_I2C
-+ help
-+ Say Y or M if you want to add support for ADAU1977 ADC.
---- a/sound/soc/bcm/Makefile
-+++ b/sound/soc/bcm/Makefile
-@@ -4,6 +4,7 @@ snd-soc-bcm2835-i2s-objs := bcm2835-i2s.
- obj-$(CONFIG_SND_BCM2835_SOC_I2S) += snd-soc-bcm2835-i2s.o
-
- # BCM2708 Machine Support
-+snd-soc-adau1977-adc-objs := adau1977-adc.o
- snd-soc-hifiberry-dac-objs := hifiberry_dac.o
- snd-soc-hifiberry-dacplus-objs := hifiberry_dacplus.o
- snd-soc-hifiberry-digi-objs := hifiberry_digi.o
-@@ -15,6 +16,7 @@ snd-soc-rpi-proto-objs := rpi-proto.o
- snd-soc-iqaudio-dac-objs := iqaudio-dac.o
- snd-soc-raspidac3-objs := raspidac3.o
-
-+obj-$(CONFIG_SND_BCM2708_SOC_ADAU1977_ADC) += snd-soc-adau1977-adc.o
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DAC) += snd-soc-hifiberry-dac.o
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DACPLUS) += snd-soc-hifiberry-dacplus.o
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DIGI) += snd-soc-hifiberry-digi.o
---- /dev/null
-+++ b/sound/soc/bcm/adau1977-adc.c
-@@ -0,0 +1,125 @@
-+/*
-+ * ASoC Driver for ADAU1977 ADC
-+ *
-+ * Author: Andrey Grodzovsky <andrey2805 at gmail.com>
-+ * Copyright 2016
-+ *
-+ * This file is based on hifibery_dac driver by Florian Meier.
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * version 2 as published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful, but
-+ * WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
-+ * General Public License for more details.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+
-+#include <sound/core.h>
-+#include <sound/pcm.h>
-+#include <sound/pcm_params.h>
-+#include <sound/soc.h>
-+#include <sound/jack.h>
-+
-+enum adau1977_clk_id {
-+ ADAU1977_SYSCLK,
-+};
-+
-+enum adau1977_sysclk_src {
-+ ADAU1977_SYSCLK_SRC_MCLK,
-+ ADAU1977_SYSCLK_SRC_LRCLK,
-+};
-+
-+static int eval_adau1977_init(struct snd_soc_pcm_runtime *rtd)
-+{
-+ int ret;
-+ struct snd_soc_dai *codec_dai = rtd->codec_dai;
-+
-+ ret = snd_soc_dai_set_tdm_slot(codec_dai, 0, 0, 0, 0);
-+ if (ret < 0)
-+ return ret;
-+
-+ return snd_soc_codec_set_sysclk(rtd->codec, ADAU1977_SYSCLK,
-+ ADAU1977_SYSCLK_SRC_MCLK, 11289600, SND_SOC_CLOCK_IN);
-+}
-+
-+static struct snd_soc_dai_link snd_rpi_adau1977_dai[] = {
-+ {
-+ .name = "adau1977",
-+ .stream_name = "ADAU1977",
-+ .cpu_dai_name = "bcm2708-i2s.0",
-+ .codec_dai_name = "adau1977-hifi",
-+ .platform_name = "bcm2708-i2s.0",
-+ .codec_name = "adau1977.1-0011",
-+ .init = eval_adau1977_init,
-+ .dai_fmt = SND_SOC_DAIFMT_I2S |
-+ SND_SOC_DAIFMT_NB_NF |
-+ SND_SOC_DAIFMT_CBM_CFM,
-+ },
-+};
-+
-+/* audio machine driver */
-+static struct snd_soc_card snd_adau1977_adc = {
-+ .name = "snd_rpi_adau1977_adc",
-+ .owner = THIS_MODULE,
-+ .dai_link = snd_rpi_adau1977_dai,
-+ .num_links = ARRAY_SIZE(snd_rpi_adau1977_dai),
-+};
-+
-+static int snd_adau1977_adc_probe(struct platform_device *pdev)
-+{
-+ int ret = 0;
-+
-+ snd_adau1977_adc.dev = &pdev->dev;
-+ if (pdev->dev.of_node) {
-+ struct device_node *i2s_node;
-+ struct snd_soc_dai_link *dai = &snd_rpi_adau1977_dai[0];
-+ i2s_node = of_parse_phandle(pdev->dev.of_node,
-+ "i2s-controller", 0);
-+
-+ if (i2s_node) {
-+ dai->cpu_dai_name = NULL;
-+ dai->cpu_of_node = i2s_node;
-+ dai->platform_name = NULL;
-+ dai->platform_of_node = i2s_node;
-+ }
-+ }
-+
-+ ret = snd_soc_register_card(&snd_adau1977_adc);
-+ if (ret)
-+ dev_err(&pdev->dev, "snd_soc_register_card() failed: %d\n", ret);
-+
-+ return ret;
-+}
-+
-+static int snd_adau1977_adc_remove(struct platform_device *pdev)
-+{
-+ return snd_soc_unregister_card(&snd_adau1977_adc);
-+}
-+
-+static const struct of_device_id snd_adau1977_adc_of_match[] = {
-+ { .compatible = "adi,adau1977-adc", },
-+ {},
-+};
-+
-+MODULE_DEVICE_TABLE(of, snd_adau1977_adc_of_match);
-+
-+static struct platform_driver snd_adau1977_adc_driver = {
-+ .driver = {
-+ .name = "snd-adau1977-adc",
-+ .owner = THIS_MODULE,
-+ .of_match_table = snd_adau1977_adc_of_match,
-+ },
-+ .probe = snd_adau1977_adc_probe,
-+ .remove = snd_adau1977_adc_remove,
-+};
-+
-+module_platform_driver(snd_adau1977_adc_driver);
-+
-+MODULE_AUTHOR("Andrey Grodzovsky <andrey2805 at gmail.com>");
-+MODULE_DESCRIPTION("ASoC Driver for ADAU1977 ADC");
-+MODULE_LICENSE("GPL v2");
diff --git a/target/linux/brcm2708/patches-4.4/0323-Allow-up-to-24dB-digital-gain-to-be-applied-when-usi.patch b/target/linux/brcm2708/patches-4.4/0323-Allow-up-to-24dB-digital-gain-to-be-applied-when-usi.patch
deleted file mode 100644
index 76b98a5..0000000
--- a/target/linux/brcm2708/patches-4.4/0323-Allow-up-to-24dB-digital-gain-to-be-applied-when-usi.patch
+++ /dev/null
@@ -1,60 +0,0 @@
-From f8abdaaf67f76c85eff5d5b2d38603b0dbaaf6be Mon Sep 17 00:00:00 2001
-From: DigitalDreamtime <clive.messer at digitaldreamtime.co.uk>
-Date: Fri, 6 May 2016 09:42:55 +0100
-Subject: [PATCH] Allow up to 24dB digital gain to be applied when using
- IQAudIO DAC
-
-24db_digital_gain DT param can be used to specify that PCM512x
-codec "Digital" volume control should not be limited to 0dB gain,
-and if specified will allow the full 24dB gain.
-
-Signed-off-by: DigitalDreamtime <clive.messer at digitaldreamtime.co.uk>
----
- arch/arm/boot/dts/overlays/README | 17 +++++++++++++++--
- arch/arm/boot/dts/overlays/iqaudio-dac-overlay.dts | 6 +++++-
- 2 files changed, 20 insertions(+), 3 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -490,8 +490,21 @@ Params: <None>
-
- Name: iqaudio-dac
- Info: Configures the IQaudio DAC audio card
--Load: dtoverlay=iqaudio-dac
--Params: <None>
-+Load: dtoverlay=iqaudio-dac,<param>
-+Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec
-+ Digital volume control. Enable with
-+ "dtoverlay=iqaudio-dac,24db_digital_gain"
-+ (The default behaviour is that the Digital
-+ volume control is limited to a maximum of
-+ 0dB. ie. it can attenuate but not provide
-+ gain. For most users, this will be desired
-+ as it will prevent clipping. By appending
-+ the 24db_digital_gain parameter, the Digital
-+ volume control will allow up to 24dB of
-+ gain. If this parameter is enabled, it is the
-+ responsibility of the user to ensure that
-+ the Digital volume control is set to a value
-+ that does not result in clipping/distortion!)
-
-
- Name: iqaudio-dacplus
---- a/arch/arm/boot/dts/overlays/iqaudio-dac-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/iqaudio-dac-overlay.dts
-@@ -30,10 +30,14 @@
-
- fragment at 2 {
- target = <&sound>;
-- __overlay__ {
-+ frag2: __overlay__ {
- compatible = "iqaudio,iqaudio-dac";
- i2s-controller = <&i2s>;
- status = "okay";
- };
- };
-+
-+ __overrides__ {
-+ 24db_digital_gain = <&frag2>,"iqaudio,24db_digital_gain?";
-+ };
- };
diff --git a/target/linux/brcm2708/patches-4.4/0324-config-Add-CONFIG_DRM_LOAD_EDID_FIRMWARE.patch b/target/linux/brcm2708/patches-4.4/0324-config-Add-CONFIG_DRM_LOAD_EDID_FIRMWARE.patch
deleted file mode 100644
index 5ff57f4..0000000
--- a/target/linux/brcm2708/patches-4.4/0324-config-Add-CONFIG_DRM_LOAD_EDID_FIRMWARE.patch
+++ /dev/null
@@ -1,30 +0,0 @@
-From 8b3a4ebc9b42a759c70234ba6e87aa01e7253550 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Fri, 6 May 2016 12:40:37 +0100
-Subject: [PATCH] config: Add CONFIG_DRM_LOAD_EDID_FIRMWARE
-
----
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 2 files changed, 2 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -815,6 +815,7 @@ CONFIG_VIDEO_TW9906=m
- CONFIG_VIDEO_OV7640=m
- CONFIG_VIDEO_MT9V011=m
- CONFIG_DRM=m
-+CONFIG_DRM_LOAD_EDID_FIRMWARE=y
- CONFIG_DRM_UDL=m
- CONFIG_DRM_VC4=m
- CONFIG_FB=y
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -807,6 +807,7 @@ CONFIG_VIDEO_TW9906=m
- CONFIG_VIDEO_OV7640=m
- CONFIG_VIDEO_MT9V011=m
- CONFIG_DRM=m
-+CONFIG_DRM_LOAD_EDID_FIRMWARE=y
- CONFIG_DRM_UDL=m
- CONFIG_DRM_VC4=m
- CONFIG_FB=y
diff --git a/target/linux/brcm2708/patches-4.4/0325-BCM270X_DT-Move-vc4-node-contents-to-bcm2708_common..patch b/target/linux/brcm2708/patches-4.4/0325-BCM270X_DT-Move-vc4-node-contents-to-bcm2708_common..patch
deleted file mode 100644
index 38aa269..0000000
--- a/target/linux/brcm2708/patches-4.4/0325-BCM270X_DT-Move-vc4-node-contents-to-bcm2708_common..patch
+++ /dev/null
@@ -1,324 +0,0 @@
-From 7802e183f782f20a30d629cef099c911c07e0e4d Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 6 May 2016 11:48:35 -0700
-Subject: [PATCH] BCM270X_DT: Move vc4 node contents to bcm2708_common.dtsi.
-
-This should clarify what's going on with the overlay: The hardware is
-always present, we're just enabling the DT node so that the vc4 driver
-probes.
-
-The interrupts are left in the overlay, because the firmware doesn't
-check node status before masking out the vc4 interrupts.
-
-By having the nodes in the common file, we'll be able to correctly
-connect the HDMI HPD GPIO so that we can detect whether an HDMI
-monitor is connected.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- arch/arm/boot/dts/bcm2708_common.dtsi | 51 +++++++
- arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts | 160 ++++++++++-----------
- 2 files changed, 129 insertions(+), 82 deletions(-)
-
---- a/arch/arm/boot/dts/bcm2708_common.dtsi
-+++ b/arch/arm/boot/dts/bcm2708_common.dtsi
-@@ -1,4 +1,7 @@
-+#include "dt-bindings/clock/bcm2835.h"
- #include <dt-bindings/clock/bcm2835-aux.h>
-+#include "dt-bindings/power/raspberrypi-power.h"
-+#include "dt-bindings/gpio/gpio.h"
- #include "skeleton.dtsi"
-
- / {
-@@ -170,6 +173,18 @@
- status = "disabled";
- };
-
-+ pixelvalve0: pixelvalve at 7e206000 {
-+ compatible = "brcm,bcm2835-pixelvalve0";
-+ reg = <0x7e206000 0x100>;
-+ status = "disabled";
-+ };
-+
-+ pixelvalve1: pixelvalve at 7e207000 {
-+ compatible = "brcm,bcm2835-pixelvalve1";
-+ reg = <0x7e207000 0x100>;
-+ status = "disabled";
-+ };
-+
- pwm: pwm at 7e20c000 {
- compatible = "brcm,bcm2835-pwm";
- reg = <0x7e20c000 0x28>;
-@@ -227,6 +242,12 @@
- status = "disabled";
- };
-
-+ hvs: hvs at 7e400000 {
-+ compatible = "brcm,bcm2835-hvs";
-+ reg = <0x7e400000 0x6000>;
-+ status = "disabled";
-+ };
-+
- i2c1: i2c at 7e804000 {
- compatible = "brcm,bcm2708-i2c";
- reg = <0x7e804000 0x1000>;
-@@ -261,6 +282,25 @@
- status = "disabled";
- };
-
-+ pixelvalve2: pixelvalve at 7e807000 {
-+ compatible = "brcm,bcm2835-pixelvalve2";
-+ reg = <0x7e807000 0x100>;
-+ status = "disabled";
-+ };
-+
-+ hdmi: hdmi at 7e902000 {
-+ compatible = "brcm,bcm2835-hdmi";
-+ reg = <0x7e902000 0x600>,
-+ <0x7e808000 0x100>;
-+ ddc = <&i2c2>;
-+ hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
-+ clocks = <&cprman BCM2835_PLLH_PIX>,
-+ <&cprman BCM2835_CLOCK_HSM>;
-+ clock-names = "pixel", "hdmi";
-+ power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
-+ status = "disabled";
-+ };
-+
- usb: usb at 7e980000 {
- compatible = "brcm,bcm2708-usb";
- reg = <0x7e980000 0x10000>,
-@@ -269,6 +309,12 @@
- <1 9>;
- };
-
-+ v3d: v3d at 7ec00000 {
-+ compatible = "brcm,vc4-v3d";
-+ reg = <0x7ec00000 0x1000>;
-+ status = "disabled";
-+ };
-+
- firmware: firmware {
- compatible = "raspberrypi,bcm2835-firmware";
- mboxes = <&mailbox>;
-@@ -303,6 +349,11 @@
- firmware = <&firmware>;
- };
-
-+ gpu: gpu {
-+ compatible = "brcm,bcm2835-vc4";
-+ status = "disabled";
-+ };
-+
- /* Onboard audio */
- audio: audio {
- compatible = "brcm,bcm2835-audio";
---- a/arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts
-@@ -5,129 +5,125 @@
- /dts-v1/;
- /plugin/;
-
--#include "dt-bindings/clock/bcm2835.h"
--#include "dt-bindings/power/raspberrypi-power.h"
--#include "dt-bindings/gpio/gpio.h"
--
- / {
- compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-
- fragment at 0 {
-+ target-path = "/chosen";
-+ __overlay__ {
-+ bootargs = "cma=256M at 256M";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target-path = "/chosen";
-+ __dormant__ {
-+ bootargs = "cma=192M at 256M";
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target-path = "/chosen";
-+ __dormant__ {
-+ bootargs = "cma=128M at 128M";
-+ };
-+ };
-+
-+ fragment at 3 {
-+ target-path = "/chosen";
-+ __dormant__ {
-+ bootargs = "cma=96M at 128M";
-+ };
-+ };
-+
-+ fragment at 4 {
-+ target-path = "/chosen";
-+ __dormant__ {
-+ bootargs = "cma=64M at 64M";
-+ };
-+ };
-+
-+ fragment at 5 {
- target = <&i2c2>;
- __overlay__ {
- status = "okay";
- };
- };
-
-- fragment at 1 {
-+ fragment at 6 {
- target = <&cprman>;
- __overlay__ {
- status = "okay";
- };
- };
-
-- fragment at 2 {
-+ fragment at 7 {
- target = <&fb>;
- __overlay__ {
- status = "disabled";
- };
- };
-
-- fragment at 3 {
-- target = <&soc>;
-+ fragment at 8 {
-+ target = <&pixelvalve0>;
- __overlay__ {
-- #address-cells = <1>;
-- #size-cells = <1>;
-+ interrupts = <2 13>; /* pwa0 */
-+ status = "okay";
-+ };
-+ };
-
-- pixelvalve at 7e206000 {
-- compatible = "brcm,bcm2835-pixelvalve0";
-- reg = <0x7e206000 0x100>;
-- interrupts = <2 13>; /* pwa0 */
-- };
--
-- pixelvalve at 7e207000 {
-- compatible = "brcm,bcm2835-pixelvalve1";
-- reg = <0x7e207000 0x100>;
-- interrupts = <2 14>; /* pwa1 */
-- };
--
-- hvs at 7e400000 {
-- compatible = "brcm,bcm2835-hvs";
-- reg = <0x7e400000 0x6000>;
-- interrupts = <2 1>;
-- };
--
-- pixelvalve at 7e807000 {
-- compatible = "brcm,bcm2835-pixelvalve2";
-- reg = <0x7e807000 0x100>;
-- interrupts = <2 10>; /* pixelvalve */
-- };
--
-- hdmi at 7e902000 {
-- compatible = "brcm,bcm2835-hdmi";
-- reg = <0x7e902000 0x600>,
-- <0x7e808000 0x100>;
-- interrupts = <2 8>, <2 9>;
-- ddc = <&i2c2>;
-- hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
-- clocks = <&cprman BCM2835_PLLH_PIX>,
-- <&cprman BCM2835_CLOCK_HSM>;
-- clock-names = "pixel", "hdmi";
-- power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
-- };
--
-- v3d at 7ec00000 {
-- compatible = "brcm,vc4-v3d";
-- reg = <0x7ec00000 0x1000>;
-- interrupts = <1 10>;
-- };
--
-- gpu at 7e4c0000 {
-- compatible = "brcm,bcm2835-vc4";
-- };
-+ fragment at 9 {
-+ target = <&pixelvalve1>;
-+ __overlay__ {
-+ interrupts = <2 14>; /* pwa1 */
-+ status = "okay";
- };
- };
-
-- fragment at 4 {
-- target-path = "/chosen";
-- __overlay__ {
-- bootargs = "cma=256M at 256M";
-+ fragment at 10 {
-+ target = <&pixelvalve2>;
-+ __overlay__ {
-+ interrupts = <2 10>; /* pixelvalve */
-+ status = "okay";
- };
- };
-
-- fragment at 5 {
-- target-path = "/chosen";
-- __dormant__ {
-- bootargs = "cma=192M at 256M";
-+ fragment at 11 {
-+ target = <&hvs>;
-+ __overlay__ {
-+ interrupts = <2 1>;
-+ status = "okay";
- };
- };
-
-- fragment at 6 {
-- target-path = "/chosen";
-- __dormant__ {
-- bootargs = "cma=128M at 128M";
-+ fragment at 12 {
-+ target = <&hdmi>;
-+ __overlay__ {
-+ interrupts = <2 8>, <2 9>;
-+ status = "okay";
- };
- };
-
-- fragment at 7 {
-- target-path = "/chosen";
-- __dormant__ {
-- bootargs = "cma=96M at 128M";
-+ fragment at 13 {
-+ target = <&v3d>;
-+ __overlay__ {
-+ interrupts = <1 10>;
-+ status = "okay";
- };
- };
-
-- fragment at 8 {
-- target-path = "/chosen";
-- __dormant__ {
-- bootargs = "cma=64M at 64M";
-+ fragment at 14 {
-+ target = <&gpu>;
-+ __overlay__ {
-+ status = "okay";
- };
- };
-
- __overrides__ {
-- cma-256 = <0>,"+4-5-6-7-8";
-- cma-192 = <0>,"-4+5-6-7-8";
-- cma-128 = <0>,"-4-5+6-7-8";
-- cma-96 = <0>,"-4-5-6+7-8";
-- cma-64 = <0>,"-4-5-6-7+8";
-+ cma-256 = <0>,"+0-1-2-3-4";
-+ cma-192 = <0>,"-0+1-2-3-4";
-+ cma-128 = <0>,"-0-1+2-3-4";
-+ cma-96 = <0>,"-0-1-2+3-4";
-+ cma-64 = <0>,"-0-1-2-3+4";
- };
- };
diff --git a/target/linux/brcm2708/patches-4.4/0326-BCM270X_DT-Set-correct-HDMI-HPD-GPIO-levels-for-vari.patch b/target/linux/brcm2708/patches-4.4/0326-BCM270X_DT-Set-correct-HDMI-HPD-GPIO-levels-for-vari.patch
deleted file mode 100644
index 3cac1bf..0000000
--- a/target/linux/brcm2708/patches-4.4/0326-BCM270X_DT-Set-correct-HDMI-HPD-GPIO-levels-for-vari.patch
+++ /dev/null
@@ -1,69 +0,0 @@
-From fd4fa552546b0817e90d5ebab1889b51e46f23fa Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 6 May 2016 12:42:26 -0700
-Subject: [PATCH] BCM270X_DT: Set correct HDMI HPD GPIO levels for various
- boards.
-
-The CM is left out, because I haven't found a source for how the CM's
-HPD is connected.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- arch/arm/boot/dts/bcm2708-rpi-b-plus.dts | 4 ++++
- arch/arm/boot/dts/bcm2708-rpi-b.dts | 4 ++++
- arch/arm/boot/dts/bcm2709-rpi-2-b.dts | 4 ++++
- arch/arm/boot/dts/bcm2710-rpi-3-b.dts | 4 ++++
- 4 files changed, 16 insertions(+)
-
---- a/arch/arm/boot/dts/bcm2708-rpi-b-plus.dts
-+++ b/arch/arm/boot/dts/bcm2708-rpi-b-plus.dts
-@@ -116,6 +116,10 @@
- };
- };
-
-+&hdmi {
-+ hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
-+};
-+
- / {
- __overrides__ {
- uart0 = <&uart0>,"status";
---- a/arch/arm/boot/dts/bcm2708-rpi-b.dts
-+++ b/arch/arm/boot/dts/bcm2708-rpi-b.dts
-@@ -110,6 +110,10 @@
- };
- };
-
-+&hdmi {
-+ hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
-+};
-+
- / {
- __overrides__ {
- uart0 = <&uart0>,"status";
---- a/arch/arm/boot/dts/bcm2709-rpi-2-b.dts
-+++ b/arch/arm/boot/dts/bcm2709-rpi-2-b.dts
-@@ -116,6 +116,10 @@
- };
- };
-
-+&hdmi {
-+ hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
-+};
-+
- / {
- __overrides__ {
- uart0 = <&uart0>,"status";
---- a/arch/arm/boot/dts/bcm2710-rpi-3-b.dts
-+++ b/arch/arm/boot/dts/bcm2710-rpi-3-b.dts
-@@ -161,6 +161,10 @@
- };
- };
-
-+&hdmi {
-+ hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
-+};
-+
- / {
- chosen {
- bootargs = "8250.nr_uarts=1";
diff --git a/target/linux/brcm2708/patches-4.4/0327-Revert-drm-vc4-Force-HDMI-to-connected.patch b/target/linux/brcm2708/patches-4.4/0327-Revert-drm-vc4-Force-HDMI-to-connected.patch
deleted file mode 100644
index 14039aa..0000000
--- a/target/linux/brcm2708/patches-4.4/0327-Revert-drm-vc4-Force-HDMI-to-connected.patch
+++ /dev/null
@@ -1,26 +0,0 @@
-From a67ee5f0bbd45f70a72e3c25e96e72f4f1add7d2 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 6 May 2016 12:43:25 -0700
-Subject: [PATCH] Revert "drm/vc4: Force HDMI to connected."
-
-Now that we have the HDMI HPD GPIOs correctly identified in the DT, we
-should be able to successfully detect HDMI.
-
-This reverts commit fbec01e2d17b924d91850e17eeecf975e74c9ebf.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_hdmi.c | 2 --
- 1 file changed, 2 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_hdmi.c
-+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
-@@ -166,8 +166,6 @@ vc4_hdmi_connector_detect(struct drm_con
- struct drm_device *dev = connector->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
-
-- return connector_status_connected;
--
- if (vc4->hdmi->hpd_gpio) {
- if (gpio_get_value_cansleep(vc4->hdmi->hpd_gpio) ^
- vc4->hdmi->hpd_active_low)
diff --git a/target/linux/brcm2708/patches-4.4/0328-BCM270X-Include-DRM_PANEL_SIMPLE-in-the-defconfigs.patch b/target/linux/brcm2708/patches-4.4/0328-BCM270X-Include-DRM_PANEL_SIMPLE-in-the-defconfigs.patch
deleted file mode 100644
index 9807745..0000000
--- a/target/linux/brcm2708/patches-4.4/0328-BCM270X-Include-DRM_PANEL_SIMPLE-in-the-defconfigs.patch
+++ /dev/null
@@ -1,33 +0,0 @@
-From ff0917e1fd02a71d3eacdfebb0e666fd8f5267e9 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 6 May 2016 12:59:27 -0700
-Subject: [PATCH] BCM270X: Include DRM_PANEL_SIMPLE in the defconfigs.
-
-This is going to be required for the Adafruit DPI panel support.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 2 files changed, 2 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -817,6 +817,7 @@ CONFIG_VIDEO_MT9V011=m
- CONFIG_DRM=m
- CONFIG_DRM_LOAD_EDID_FIRMWARE=y
- CONFIG_DRM_UDL=m
-+CONFIG_DRM_PANEL_SIMPLE=m
- CONFIG_DRM_VC4=m
- CONFIG_FB=y
- CONFIG_FB_BCM2708=y
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -809,6 +809,7 @@ CONFIG_VIDEO_MT9V011=m
- CONFIG_DRM=m
- CONFIG_DRM_LOAD_EDID_FIRMWARE=y
- CONFIG_DRM_UDL=m
-+CONFIG_DRM_PANEL_SIMPLE=m
- CONFIG_DRM_VC4=m
- CONFIG_FB=y
- CONFIG_FB_BCM2708=y
diff --git a/target/linux/brcm2708/patches-4.4/0329-drm-Add-an-encoder-and-connector-type-enum-for-DPI.patch b/target/linux/brcm2708/patches-4.4/0329-drm-Add-an-encoder-and-connector-type-enum-for-DPI.patch
deleted file mode 100644
index e9cec59..0000000
--- a/target/linux/brcm2708/patches-4.4/0329-drm-Add-an-encoder-and-connector-type-enum-for-DPI.patch
+++ /dev/null
@@ -1,64 +0,0 @@
-From 99dcc59ce1c684c1138a70e0a02dd9a40512f29a Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 18 Mar 2016 12:34:59 -0700
-Subject: [PATCH] drm: Add an encoder and connector type enum for DPI.
-
-Right now exynos is exposing DPI as a TMDS encoder and VGA connector,
-which seems rather misleading. This isn't just an internal detail,
-since xrandr actually exposes "VGA" as the output name. Define some
-new enums so that vc4's DPI can have a more informative name.
-
-I considered other names for the connector as well. For VC4, the
-Adafruit DPI kippah takes the 28 GPIO pins and routes them to a
-standard-ish 40-pin FPC connector, but "40-pin FPC" doesn't uniquely
-identify an ordering of pins (apparently some other orderings exist),
-doesn't explain things as well for the user (who, if anything, knows
-their product is a DPI kippah/panel combo), and actually doesn't have
-to exist (one could connect the 28 GPIOs directly to something else).
-Simply "DPI" seems like a good compromise name to distinguish from the
-HDMI, DSI, and TV connectors .
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Reviewed-by: Daniel Vetter <daniel.vetter at ffwll.ch>
-(cherry picked from commit 0b27c02a7f1c697694f2ad6d6517e7dbf9ecfa39)
----
- drivers/gpu/drm/drm_crtc.c | 2 ++
- include/uapi/drm/drm_mode.h | 2 ++
- 2 files changed, 4 insertions(+)
-
---- a/drivers/gpu/drm/drm_crtc.c
-+++ b/drivers/gpu/drm/drm_crtc.c
-@@ -168,6 +168,7 @@ static struct drm_conn_prop_enum_list dr
- { DRM_MODE_CONNECTOR_eDP, "eDP" },
- { DRM_MODE_CONNECTOR_VIRTUAL, "Virtual" },
- { DRM_MODE_CONNECTOR_DSI, "DSI" },
-+ { DRM_MODE_CONNECTOR_DPI, "DPI" },
- };
-
- static const struct drm_prop_enum_list drm_encoder_enum_list[] = {
-@@ -179,6 +180,7 @@ static const struct drm_prop_enum_list d
- { DRM_MODE_ENCODER_VIRTUAL, "Virtual" },
- { DRM_MODE_ENCODER_DSI, "DSI" },
- { DRM_MODE_ENCODER_DPMST, "DP MST" },
-+ { DRM_MODE_ENCODER_DPI, "DPI" },
- };
-
- static const struct drm_prop_enum_list drm_subpixel_enum_list[] = {
---- a/include/uapi/drm/drm_mode.h
-+++ b/include/uapi/drm/drm_mode.h
-@@ -202,6 +202,7 @@ struct drm_mode_get_plane_res {
- #define DRM_MODE_ENCODER_VIRTUAL 5
- #define DRM_MODE_ENCODER_DSI 6
- #define DRM_MODE_ENCODER_DPMST 7
-+#define DRM_MODE_ENCODER_DPI 8
-
- struct drm_mode_get_encoder {
- __u32 encoder_id;
-@@ -241,6 +242,7 @@ struct drm_mode_get_encoder {
- #define DRM_MODE_CONNECTOR_eDP 14
- #define DRM_MODE_CONNECTOR_VIRTUAL 15
- #define DRM_MODE_CONNECTOR_DSI 16
-+#define DRM_MODE_CONNECTOR_DPI 17
-
- struct drm_mode_get_connector {
-
diff --git a/target/linux/brcm2708/patches-4.4/0330-dt-bindings-Add-binding-docs-for-V3D.patch b/target/linux/brcm2708/patches-4.4/0330-dt-bindings-Add-binding-docs-for-V3D.patch
deleted file mode 100644
index f396d37..0000000
--- a/target/linux/brcm2708/patches-4.4/0330-dt-bindings-Add-binding-docs-for-V3D.patch
+++ /dev/null
@@ -1,42 +0,0 @@
-From e9e9d7af1d62105ade6e14bd759b9b69e804aaaa Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 4 Mar 2016 12:32:06 -0800
-Subject: [PATCH] dt-bindings: Add binding docs for V3D.
-
-This was missed in the upstreaming process.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Acked-by: Stephen Warren <swarren at wwwdotorg.org>
-(cherry picked from commit 4653f22e9ab08b2b7178b7262a9326eb777e0266)
----
- Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt | 12 ++++++++++++
- 1 file changed, 12 insertions(+)
-
---- a/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt
-+++ b/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt
-@@ -35,6 +35,12 @@ Optional properties for HDMI:
- as an interrupt/status bit in the HDMI controller
- itself). See bindings/pinctrl/brcm,bcm2835-gpio.txt
-
-+Required properties for V3D:
-+- compatible: Should be "brcm,bcm2835-v3d"
-+- reg: Physical base address and length of the V3D's registers
-+- interrupts: The interrupt number
-+ See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
-+
- Example:
- pixelvalve at 7e807000 {
- compatible = "brcm,bcm2835-pixelvalve2";
-@@ -60,6 +66,12 @@ hdmi: hdmi at 7e902000 {
- clock-names = "pixel", "hdmi";
- };
-
-+v3d: v3d at 7ec00000 {
-+ compatible = "brcm,bcm2835-v3d";
-+ reg = <0x7ec00000 0x1000>;
-+ interrupts = <1 10>;
-+};
-+
- vc4: gpu {
- compatible = "brcm,bcm2835-vc4";
- };
diff --git a/target/linux/brcm2708/patches-4.4/0331-drm-vc4-Add-DPI-driver.patch b/target/linux/brcm2708/patches-4.4/0331-drm-vc4-Add-DPI-driver.patch
deleted file mode 100644
index 0850968..0000000
--- a/target/linux/brcm2708/patches-4.4/0331-drm-vc4-Add-DPI-driver.patch
+++ /dev/null
@@ -1,673 +0,0 @@
-From 3fdffbb253cc8738bee0860f58de9ebd099afab1 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Wed, 10 Feb 2016 11:42:32 -0800
-Subject: [PATCH] drm/vc4: Add DPI driver
-
-The DPI interface involves taking a ton of our GPIOs to be used as
-outputs, and routing display signals over them in parallel.
-
-v2: Use display_info.bus_formats[] to replace our custom DT
- properties.
-v3: Rebase on V3D documentation changes.
-v4: Fix rebase detritus from V3D documentation changes.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Acked-by: Rob Herring <robh at kernel.org>
-(cherry picked from commit 08302c35b59d306ff37b996e56fb2a488c1d2c2e)
----
- .../devicetree/bindings/display/brcm,bcm-vc4.txt | 36 ++
- drivers/gpu/drm/vc4/Kconfig | 1 +
- drivers/gpu/drm/vc4/Makefile | 1 +
- drivers/gpu/drm/vc4/vc4_debugfs.c | 1 +
- drivers/gpu/drm/vc4/vc4_dpi.c | 520 +++++++++++++++++++++
- drivers/gpu/drm/vc4/vc4_drv.c | 1 +
- drivers/gpu/drm/vc4/vc4_drv.h | 5 +
- 7 files changed, 565 insertions(+)
- create mode 100644 drivers/gpu/drm/vc4/vc4_dpi.c
-
---- a/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt
-+++ b/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt
-@@ -35,12 +35,22 @@ Optional properties for HDMI:
- as an interrupt/status bit in the HDMI controller
- itself). See bindings/pinctrl/brcm,bcm2835-gpio.txt
-
-+Required properties for DPI:
-+- compatible: Should be "brcm,bcm2835-dpi"
-+- reg: Physical base address and length of the registers
-+- clocks: a) core: The core clock the unit runs on
-+ b) pixel: The pixel clock that feeds the pixelvalve
-+- port: Port node with a single endpoint connecting to the panel
-+ device, as defined in [1]
-+
- Required properties for V3D:
- - compatible: Should be "brcm,bcm2835-v3d"
- - reg: Physical base address and length of the V3D's registers
- - interrupts: The interrupt number
- See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
-
-+[1] Documentation/devicetree/bindings/media/video-interfaces.txt
-+
- Example:
- pixelvalve at 7e807000 {
- compatible = "brcm,bcm2835-pixelvalve2";
-@@ -66,6 +76,22 @@ hdmi: hdmi at 7e902000 {
- clock-names = "pixel", "hdmi";
- };
-
-+dpi: dpi at 7e208000 {
-+ compatible = "brcm,bcm2835-dpi";
-+ reg = <0x7e208000 0x8c>;
-+ clocks = <&clocks BCM2835_CLOCK_VPU>,
-+ <&clocks BCM2835_CLOCK_DPI>;
-+ clock-names = "core", "pixel";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ port {
-+ dpi_out: endpoint at 0 {
-+ remote-endpoint = <&panel_in>;
-+ };
-+ };
-+};
-+
- v3d: v3d at 7ec00000 {
- compatible = "brcm,bcm2835-v3d";
- reg = <0x7ec00000 0x1000>;
-@@ -75,3 +101,13 @@ v3d: v3d at 7ec00000 {
- vc4: gpu {
- compatible = "brcm,bcm2835-vc4";
- };
-+
-+panel: panel {
-+ compatible = "ontat,yx700wv03", "simple-panel";
-+
-+ port {
-+ panel_in: endpoint {
-+ remote-endpoint = <&dpi_out>;
-+ };
-+ };
-+};
---- a/drivers/gpu/drm/vc4/Kconfig
-+++ b/drivers/gpu/drm/vc4/Kconfig
-@@ -5,6 +5,7 @@ config DRM_VC4
- select DRM_KMS_HELPER
- select DRM_KMS_CMA_HELPER
- select DRM_GEM_CMA_HELPER
-+ select DRM_PANEL
- help
- Choose this option if you have a system that has a Broadcom
- VC4 GPU, such as the Raspberry Pi or other BCM2708/BCM2835.
---- a/drivers/gpu/drm/vc4/Makefile
-+++ b/drivers/gpu/drm/vc4/Makefile
-@@ -7,6 +7,7 @@ vc4-y := \
- vc4_bo.o \
- vc4_crtc.o \
- vc4_drv.o \
-+ vc4_dpi.o \
- vc4_kms.o \
- vc4_gem.o \
- vc4_hdmi.o \
---- a/drivers/gpu/drm/vc4/vc4_debugfs.c
-+++ b/drivers/gpu/drm/vc4/vc4_debugfs.c
-@@ -17,6 +17,7 @@
-
- static const struct drm_info_list vc4_debugfs_list[] = {
- {"bo_stats", vc4_bo_stats_debugfs, 0},
-+ {"dpi_regs", vc4_dpi_debugfs_regs, 0},
- {"gem_exec", vc4_gem_exec_debugfs, 0},
- {"hdmi_regs", vc4_hdmi_debugfs_regs, 0},
- {"hvs_regs", vc4_hvs_debugfs_regs, 0},
---- /dev/null
-+++ b/drivers/gpu/drm/vc4/vc4_dpi.c
-@@ -0,0 +1,520 @@
-+/*
-+ * Copyright (C) 2016 Broadcom Limited
-+ *
-+ * This program is free software; you can redistribute it and/or modify it
-+ * under the terms of the GNU General Public License version 2 as published by
-+ * the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful, but WITHOUT
-+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
-+ * more details.
-+ *
-+ * You should have received a copy of the GNU General Public License along with
-+ * this program. If not, see <http://www.gnu.org/licenses/>.
-+ */
-+
-+/**
-+ * DOC: VC4 DPI module
-+ *
-+ * The VC4 DPI hardware supports MIPI DPI type 4 and Nokia ViSSI
-+ * signals, which are routed out to GPIO0-27 with the ALT2 function.
-+ */
-+
-+#include "drm_atomic_helper.h"
-+#include "drm_crtc_helper.h"
-+#include "drm_edid.h"
-+#include "drm_panel.h"
-+#include "linux/clk.h"
-+#include "linux/component.h"
-+#include "linux/of_graph.h"
-+#include "linux/of_platform.h"
-+#include "vc4_drv.h"
-+#include "vc4_regs.h"
-+
-+#define DPI_C 0x00
-+# define DPI_OUTPUT_ENABLE_MODE BIT(16)
-+
-+/* The order field takes the incoming 24 bit RGB from the pixel valve
-+ * and shuffles the 3 channels.
-+ */
-+# define DPI_ORDER_MASK VC4_MASK(15, 14)
-+# define DPI_ORDER_SHIFT 14
-+# define DPI_ORDER_RGB 0
-+# define DPI_ORDER_BGR 1
-+# define DPI_ORDER_GRB 2
-+# define DPI_ORDER_BRG 3
-+
-+/* The format field takes the ORDER-shuffled pixel valve data and
-+ * formats it onto the output lines.
-+ */
-+# define DPI_FORMAT_MASK VC4_MASK(13, 11)
-+# define DPI_FORMAT_SHIFT 11
-+/* This define is named in the hardware, but actually just outputs 0. */
-+# define DPI_FORMAT_9BIT_666_RGB 0
-+/* Outputs 00000000rrrrrggggggbbbbb */
-+# define DPI_FORMAT_16BIT_565_RGB_1 1
-+/* Outputs 000rrrrr00gggggg000bbbbb */
-+# define DPI_FORMAT_16BIT_565_RGB_2 2
-+/* Outputs 00rrrrr000gggggg00bbbbb0 */
-+# define DPI_FORMAT_16BIT_565_RGB_3 3
-+/* Outputs 000000rrrrrrggggggbbbbbb */
-+# define DPI_FORMAT_18BIT_666_RGB_1 4
-+/* Outputs 00rrrrrr00gggggg00bbbbbb */
-+# define DPI_FORMAT_18BIT_666_RGB_2 5
-+/* Outputs rrrrrrrrggggggggbbbbbbbb */
-+# define DPI_FORMAT_24BIT_888_RGB 6
-+
-+/* Reverses the polarity of the corresponding signal */
-+# define DPI_PIXEL_CLK_INVERT BIT(10)
-+# define DPI_HSYNC_INVERT BIT(9)
-+# define DPI_VSYNC_INVERT BIT(8)
-+# define DPI_OUTPUT_ENABLE_INVERT BIT(7)
-+
-+/* Outputs the signal the falling clock edge instead of rising. */
-+# define DPI_HSYNC_NEGATE BIT(6)
-+# define DPI_VSYNC_NEGATE BIT(5)
-+# define DPI_OUTPUT_ENABLE_NEGATE BIT(4)
-+
-+/* Disables the signal */
-+# define DPI_HSYNC_DISABLE BIT(3)
-+# define DPI_VSYNC_DISABLE BIT(2)
-+# define DPI_OUTPUT_ENABLE_DISABLE BIT(1)
-+
-+/* Power gate to the device, full reset at 0 -> 1 transition */
-+# define DPI_ENABLE BIT(0)
-+
-+/* All other registers besides DPI_C return the ID */
-+#define DPI_ID 0x04
-+# define DPI_ID_VALUE 0x00647069
-+
-+/* General DPI hardware state. */
-+struct vc4_dpi {
-+ struct platform_device *pdev;
-+
-+ struct drm_encoder *encoder;
-+ struct drm_connector *connector;
-+ struct drm_panel *panel;
-+
-+ void __iomem *regs;
-+
-+ struct clk *pixel_clock;
-+ struct clk *core_clock;
-+};
-+
-+#define DPI_READ(offset) readl(dpi->regs + (offset))
-+#define DPI_WRITE(offset, val) writel(val, dpi->regs + (offset))
-+
-+/* VC4 DPI encoder KMS struct */
-+struct vc4_dpi_encoder {
-+ struct vc4_encoder base;
-+ struct vc4_dpi *dpi;
-+};
-+
-+static inline struct vc4_dpi_encoder *
-+to_vc4_dpi_encoder(struct drm_encoder *encoder)
-+{
-+ return container_of(encoder, struct vc4_dpi_encoder, base.base);
-+}
-+
-+/* VC4 DPI connector KMS struct */
-+struct vc4_dpi_connector {
-+ struct drm_connector base;
-+ struct vc4_dpi *dpi;
-+
-+ /* Since the connector is attached to just the one encoder,
-+ * this is the reference to it so we can do the best_encoder()
-+ * hook.
-+ */
-+ struct drm_encoder *encoder;
-+};
-+
-+static inline struct vc4_dpi_connector *
-+to_vc4_dpi_connector(struct drm_connector *connector)
-+{
-+ return container_of(connector, struct vc4_dpi_connector, base);
-+}
-+
-+#define DPI_REG(reg) { reg, #reg }
-+static const struct {
-+ u32 reg;
-+ const char *name;
-+} dpi_regs[] = {
-+ DPI_REG(DPI_C),
-+ DPI_REG(DPI_ID),
-+};
-+
-+static void vc4_dpi_dump_regs(struct vc4_dpi *dpi)
-+{
-+ int i;
-+
-+ for (i = 0; i < ARRAY_SIZE(dpi_regs); i++) {
-+ DRM_INFO("0x%04x (%s): 0x%08x\n",
-+ dpi_regs[i].reg, dpi_regs[i].name,
-+ DPI_READ(dpi_regs[i].reg));
-+ }
-+}
-+
-+#ifdef CONFIG_DEBUG_FS
-+int vc4_dpi_debugfs_regs(struct seq_file *m, void *unused)
-+{
-+ struct drm_info_node *node = (struct drm_info_node *)m->private;
-+ struct drm_device *dev = node->minor->dev;
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ struct vc4_dpi *dpi = vc4->dpi;
-+ int i;
-+
-+ if (!dpi)
-+ return 0;
-+
-+ for (i = 0; i < ARRAY_SIZE(dpi_regs); i++) {
-+ seq_printf(m, "%s (0x%04x): 0x%08x\n",
-+ dpi_regs[i].name, dpi_regs[i].reg,
-+ DPI_READ(dpi_regs[i].reg));
-+ }
-+
-+ return 0;
-+}
-+#endif
-+
-+static enum drm_connector_status
-+vc4_dpi_connector_detect(struct drm_connector *connector, bool force)
-+{
-+ struct vc4_dpi_connector *vc4_connector =
-+ to_vc4_dpi_connector(connector);
-+ struct vc4_dpi *dpi = vc4_connector->dpi;
-+
-+ if (dpi->panel)
-+ return connector_status_connected;
-+ else
-+ return connector_status_disconnected;
-+}
-+
-+static void vc4_dpi_connector_destroy(struct drm_connector *connector)
-+{
-+ drm_connector_unregister(connector);
-+ drm_connector_cleanup(connector);
-+}
-+
-+static int vc4_dpi_connector_get_modes(struct drm_connector *connector)
-+{
-+ struct vc4_dpi_connector *vc4_connector =
-+ to_vc4_dpi_connector(connector);
-+ struct vc4_dpi *dpi = vc4_connector->dpi;
-+
-+ if (dpi->panel)
-+ return drm_panel_get_modes(dpi->panel);
-+
-+ return 0;
-+}
-+
-+static struct drm_encoder *
-+vc4_dpi_connector_best_encoder(struct drm_connector *connector)
-+{
-+ struct vc4_dpi_connector *dpi_connector =
-+ to_vc4_dpi_connector(connector);
-+ return dpi_connector->encoder;
-+}
-+
-+static const struct drm_connector_funcs vc4_dpi_connector_funcs = {
-+ .dpms = drm_atomic_helper_connector_dpms,
-+ .detect = vc4_dpi_connector_detect,
-+ .fill_modes = drm_helper_probe_single_connector_modes,
-+ .destroy = vc4_dpi_connector_destroy,
-+ .reset = drm_atomic_helper_connector_reset,
-+ .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
-+ .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
-+};
-+
-+static const struct drm_connector_helper_funcs vc4_dpi_connector_helper_funcs = {
-+ .get_modes = vc4_dpi_connector_get_modes,
-+ .best_encoder = vc4_dpi_connector_best_encoder,
-+};
-+
-+static struct drm_connector *vc4_dpi_connector_init(struct drm_device *dev,
-+ struct vc4_dpi *dpi)
-+{
-+ struct drm_connector *connector = NULL;
-+ struct vc4_dpi_connector *dpi_connector;
-+ int ret = 0;
-+
-+ dpi_connector = devm_kzalloc(dev->dev, sizeof(*dpi_connector),
-+ GFP_KERNEL);
-+ if (!dpi_connector) {
-+ ret = -ENOMEM;
-+ goto fail;
-+ }
-+ connector = &dpi_connector->base;
-+
-+ dpi_connector->encoder = dpi->encoder;
-+ dpi_connector->dpi = dpi;
-+
-+ drm_connector_init(dev, connector, &vc4_dpi_connector_funcs,
-+ DRM_MODE_CONNECTOR_DPI);
-+ drm_connector_helper_add(connector, &vc4_dpi_connector_helper_funcs);
-+
-+ connector->polled = 0;
-+ connector->interlace_allowed = 0;
-+ connector->doublescan_allowed = 0;
-+
-+ drm_mode_connector_attach_encoder(connector, dpi->encoder);
-+
-+ return connector;
-+
-+ fail:
-+ if (connector)
-+ vc4_dpi_connector_destroy(connector);
-+
-+ return ERR_PTR(ret);
-+}
-+
-+static const struct drm_encoder_funcs vc4_dpi_encoder_funcs = {
-+ .destroy = drm_encoder_cleanup,
-+};
-+
-+static void vc4_dpi_encoder_disable(struct drm_encoder *encoder)
-+{
-+ struct vc4_dpi_encoder *vc4_encoder = to_vc4_dpi_encoder(encoder);
-+ struct vc4_dpi *dpi = vc4_encoder->dpi;
-+
-+ drm_panel_disable(dpi->panel);
-+
-+ clk_disable_unprepare(dpi->pixel_clock);
-+
-+ drm_panel_unprepare(dpi->panel);
-+}
-+
-+static void vc4_dpi_encoder_enable(struct drm_encoder *encoder)
-+{
-+ struct drm_display_mode *mode = &encoder->crtc->mode;
-+ struct vc4_dpi_encoder *vc4_encoder = to_vc4_dpi_encoder(encoder);
-+ struct vc4_dpi *dpi = vc4_encoder->dpi;
-+ u32 dpi_c = DPI_ENABLE | DPI_OUTPUT_ENABLE_MODE;
-+ int ret;
-+
-+ ret = drm_panel_prepare(dpi->panel);
-+ if (ret) {
-+ DRM_ERROR("Panel failed to prepare\n");
-+ return;
-+ }
-+
-+ if (dpi->connector->display_info.num_bus_formats) {
-+ u32 bus_format = dpi->connector->display_info.bus_formats[0];
-+
-+ switch (bus_format) {
-+ case MEDIA_BUS_FMT_RGB888_1X24:
-+ dpi_c |= VC4_SET_FIELD(DPI_FORMAT_24BIT_888_RGB,
-+ DPI_FORMAT);
-+ break;
-+ case MEDIA_BUS_FMT_BGR888_1X24:
-+ dpi_c |= VC4_SET_FIELD(DPI_FORMAT_24BIT_888_RGB,
-+ DPI_FORMAT);
-+ dpi_c |= VC4_SET_FIELD(DPI_ORDER_BGR, DPI_ORDER);
-+ break;
-+ case MEDIA_BUS_FMT_RGB666_1X24_CPADHI:
-+ dpi_c |= VC4_SET_FIELD(DPI_FORMAT_18BIT_666_RGB_2,
-+ DPI_FORMAT);
-+ break;
-+ case MEDIA_BUS_FMT_RGB666_1X18:
-+ dpi_c |= VC4_SET_FIELD(DPI_FORMAT_18BIT_666_RGB_1,
-+ DPI_FORMAT);
-+ break;
-+ case MEDIA_BUS_FMT_RGB565_1X16:
-+ dpi_c |= VC4_SET_FIELD(DPI_FORMAT_16BIT_565_RGB_3,
-+ DPI_FORMAT);
-+ break;
-+ default:
-+ DRM_ERROR("Unknown media bus format %d\n", bus_format);
-+ break;
-+ }
-+ }
-+
-+ if (mode->flags & DRM_MODE_FLAG_NHSYNC)
-+ dpi_c |= DPI_HSYNC_INVERT;
-+ else if (!(mode->flags & DRM_MODE_FLAG_PHSYNC))
-+ dpi_c |= DPI_HSYNC_DISABLE;
-+
-+ if (mode->flags & DRM_MODE_FLAG_NVSYNC)
-+ dpi_c |= DPI_VSYNC_INVERT;
-+ else if (!(mode->flags & DRM_MODE_FLAG_PVSYNC))
-+ dpi_c |= DPI_VSYNC_DISABLE;
-+
-+ DPI_WRITE(DPI_C, dpi_c);
-+
-+ ret = clk_set_rate(dpi->pixel_clock, mode->clock * 1000);
-+ if (ret)
-+ DRM_ERROR("Failed to set clock rate: %d\n", ret);
-+
-+ ret = clk_prepare_enable(dpi->pixel_clock);
-+ if (ret)
-+ DRM_ERROR("Failed to set clock rate: %d\n", ret);
-+
-+ ret = drm_panel_enable(dpi->panel);
-+ if (ret) {
-+ DRM_ERROR("Panel failed to enable\n");
-+ drm_panel_unprepare(dpi->panel);
-+ return;
-+ }
-+}
-+
-+static const struct drm_encoder_helper_funcs vc4_dpi_encoder_helper_funcs = {
-+ .disable = vc4_dpi_encoder_disable,
-+ .enable = vc4_dpi_encoder_enable,
-+};
-+
-+static const struct of_device_id vc4_dpi_dt_match[] = {
-+ { .compatible = "brcm,bcm2835-dpi", .data = NULL },
-+ {}
-+};
-+
-+/* Walks the OF graph to find the panel node and then asks DRM to look
-+ * up the panel.
-+ */
-+static struct drm_panel *vc4_dpi_get_panel(struct device *dev)
-+{
-+ struct device_node *endpoint, *panel_node;
-+ struct device_node *np = dev->of_node;
-+ struct drm_panel *panel;
-+
-+ endpoint = of_graph_get_next_endpoint(np, NULL);
-+ if (!endpoint) {
-+ dev_err(dev, "no endpoint to fetch DPI panel\n");
-+ return NULL;
-+ }
-+
-+ /* don't proceed if we have an endpoint but no panel_node tied to it */
-+ panel_node = of_graph_get_remote_port_parent(endpoint);
-+ of_node_put(endpoint);
-+ if (!panel_node) {
-+ dev_err(dev, "no valid panel node\n");
-+ return NULL;
-+ }
-+
-+ panel = of_drm_find_panel(panel_node);
-+ of_node_put(panel_node);
-+
-+ return panel;
-+}
-+
-+static int vc4_dpi_bind(struct device *dev, struct device *master, void *data)
-+{
-+ struct platform_device *pdev = to_platform_device(dev);
-+ struct drm_device *drm = dev_get_drvdata(master);
-+ struct vc4_dev *vc4 = to_vc4_dev(drm);
-+ struct vc4_dpi *dpi;
-+ struct vc4_dpi_encoder *vc4_dpi_encoder;
-+ int ret;
-+
-+ dpi = devm_kzalloc(dev, sizeof(*dpi), GFP_KERNEL);
-+ if (!dpi)
-+ return -ENOMEM;
-+
-+ vc4_dpi_encoder = devm_kzalloc(dev, sizeof(*vc4_dpi_encoder),
-+ GFP_KERNEL);
-+ if (!vc4_dpi_encoder)
-+ return -ENOMEM;
-+ vc4_dpi_encoder->base.type = VC4_ENCODER_TYPE_DPI;
-+ vc4_dpi_encoder->dpi = dpi;
-+ dpi->encoder = &vc4_dpi_encoder->base.base;
-+
-+ dpi->pdev = pdev;
-+ dpi->regs = vc4_ioremap_regs(pdev, 0);
-+ if (IS_ERR(dpi->regs))
-+ return PTR_ERR(dpi->regs);
-+
-+ vc4_dpi_dump_regs(dpi);
-+
-+ if (DPI_READ(DPI_ID) != DPI_ID_VALUE) {
-+ dev_err(dev, "Port returned 0x%08x for ID instead of 0x%08x\n",
-+ DPI_READ(DPI_ID), DPI_ID_VALUE);
-+ return -ENODEV;
-+ }
-+
-+ dpi->core_clock = devm_clk_get(dev, "core");
-+ if (IS_ERR(dpi->core_clock)) {
-+ ret = PTR_ERR(dpi->core_clock);
-+ if (ret != -EPROBE_DEFER)
-+ DRM_ERROR("Failed to get core clock: %d\n", ret);
-+ return ret;
-+ }
-+ dpi->pixel_clock = devm_clk_get(dev, "pixel");
-+ if (IS_ERR(dpi->pixel_clock)) {
-+ ret = PTR_ERR(dpi->pixel_clock);
-+ if (ret != -EPROBE_DEFER)
-+ DRM_ERROR("Failed to get pixel clock: %d\n", ret);
-+ return ret;
-+ }
-+
-+ ret = clk_prepare_enable(dpi->core_clock);
-+ if (ret)
-+ DRM_ERROR("Failed to turn on core clock: %d\n", ret);
-+
-+ dpi->panel = vc4_dpi_get_panel(dev);
-+
-+ drm_encoder_init(drm, dpi->encoder, &vc4_dpi_encoder_funcs,
-+ DRM_MODE_ENCODER_DPI);
-+ drm_encoder_helper_add(dpi->encoder, &vc4_dpi_encoder_helper_funcs);
-+
-+ dpi->connector = vc4_dpi_connector_init(drm, dpi);
-+ if (IS_ERR(dpi->connector)) {
-+ ret = PTR_ERR(dpi->connector);
-+ goto err_destroy_encoder;
-+ }
-+
-+ if (dpi->panel)
-+ drm_panel_attach(dpi->panel, dpi->connector);
-+
-+ dev_set_drvdata(dev, dpi);
-+
-+ vc4->dpi = dpi;
-+
-+ return 0;
-+
-+err_destroy_encoder:
-+ drm_encoder_cleanup(dpi->encoder);
-+ clk_disable_unprepare(dpi->core_clock);
-+ return ret;
-+}
-+
-+static void vc4_dpi_unbind(struct device *dev, struct device *master,
-+ void *data)
-+{
-+ struct drm_device *drm = dev_get_drvdata(master);
-+ struct vc4_dev *vc4 = to_vc4_dev(drm);
-+ struct vc4_dpi *dpi = dev_get_drvdata(dev);
-+
-+ if (dpi->panel)
-+ drm_panel_detach(dpi->panel);
-+
-+ vc4_dpi_connector_destroy(dpi->connector);
-+ drm_encoder_cleanup(dpi->encoder);
-+
-+ clk_disable_unprepare(dpi->core_clock);
-+
-+ vc4->dpi = NULL;
-+}
-+
-+static const struct component_ops vc4_dpi_ops = {
-+ .bind = vc4_dpi_bind,
-+ .unbind = vc4_dpi_unbind,
-+};
-+
-+static int vc4_dpi_dev_probe(struct platform_device *pdev)
-+{
-+ return component_add(&pdev->dev, &vc4_dpi_ops);
-+}
-+
-+static int vc4_dpi_dev_remove(struct platform_device *pdev)
-+{
-+ component_del(&pdev->dev, &vc4_dpi_ops);
-+ return 0;
-+}
-+
-+struct platform_driver vc4_dpi_driver = {
-+ .probe = vc4_dpi_dev_probe,
-+ .remove = vc4_dpi_dev_remove,
-+ .driver = {
-+ .name = "vc4_dpi",
-+ .of_match_table = vc4_dpi_dt_match,
-+ },
-+};
---- a/drivers/gpu/drm/vc4/vc4_drv.c
-+++ b/drivers/gpu/drm/vc4/vc4_drv.c
-@@ -259,6 +259,7 @@ static const struct component_master_ops
-
- static struct platform_driver *const component_drivers[] = {
- &vc4_hdmi_driver,
-+ &vc4_dpi_driver,
- &vc4_crtc_driver,
- &vc4_hvs_driver,
- &vc4_v3d_driver,
---- a/drivers/gpu/drm/vc4/vc4_drv.h
-+++ b/drivers/gpu/drm/vc4/vc4_drv.h
-@@ -16,6 +16,7 @@ struct vc4_dev {
- struct vc4_hvs *hvs;
- struct vc4_crtc *crtc[3];
- struct vc4_v3d *v3d;
-+ struct vc4_dpi *dpi;
-
- struct drm_fbdev_cma *fbdev;
- struct rpi_firmware *firmware;
-@@ -418,6 +419,10 @@ void vc4_debugfs_cleanup(struct drm_mino
- /* vc4_drv.c */
- void __iomem *vc4_ioremap_regs(struct platform_device *dev, int index);
-
-+/* vc4_dpi.c */
-+extern struct platform_driver vc4_dpi_driver;
-+int vc4_dpi_debugfs_regs(struct seq_file *m, void *unused);
-+
- /* vc4_gem.c */
- void vc4_gem_init(struct drm_device *dev);
- void vc4_gem_destroy(struct drm_device *dev);
diff --git a/target/linux/brcm2708/patches-4.4/0332-drm-vc4-Fix-NULL-deref-in-HDMI-init-error-path.patch b/target/linux/brcm2708/patches-4.4/0332-drm-vc4-Fix-NULL-deref-in-HDMI-init-error-path.patch
deleted file mode 100644
index ebd54cc..0000000
--- a/target/linux/brcm2708/patches-4.4/0332-drm-vc4-Fix-NULL-deref-in-HDMI-init-error-path.patch
+++ /dev/null
@@ -1,25 +0,0 @@
-From bdd15a0ce3a80e58e6f3c38c11cc33f1781b8394 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 4 Apr 2016 14:25:59 -0700
-Subject: [PATCH] drm/vc4: Fix NULL deref in HDMI init error path
-
-If you make it here other than through err_destroy_encoder, vc4->hdmi
-is still NULL.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 5883980313af70aec0ceebaef6ef0709726e5e63)
----
- drivers/gpu/drm/vc4/vc4_hdmi.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/gpu/drm/vc4/vc4_hdmi.c
-+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
-@@ -573,7 +573,7 @@ err_unprepare_hsm:
- err_unprepare_pix:
- clk_disable_unprepare(hdmi->pixel_clock);
- err_put_i2c:
-- put_device(&vc4->hdmi->ddc->dev);
-+ put_device(&hdmi->ddc->dev);
-
- return ret;
- }
diff --git a/target/linux/brcm2708/patches-4.4/0333-drm-vc4-Kick-out-the-simplefb-framebuffer-before-we-.patch b/target/linux/brcm2708/patches-4.4/0333-drm-vc4-Kick-out-the-simplefb-framebuffer-before-we-.patch
deleted file mode 100644
index 1b81f66..0000000
--- a/target/linux/brcm2708/patches-4.4/0333-drm-vc4-Kick-out-the-simplefb-framebuffer-before-we-.patch
+++ /dev/null
@@ -1,53 +0,0 @@
-From 0a628ed00bf01046212f7464ac72d89a80702a46 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 19 Apr 2016 13:24:14 -0700
-Subject: [PATCH] drm/vc4: Kick out the simplefb framebuffer before we set up
- KMS.
-
-If we don't, then simplefb stays loaded on /dev/fb0 even though
-scanout isn't happening from simplefb's memory area any more, and you
-end up with no console.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Acked-by: Dave Airlie <airlied at redhat.com>
-(cherry picked from commit b3a15f6d55fb584dd4d8baac5d1b6a398720620c)
----
- drivers/gpu/drm/vc4/vc4_drv.c | 20 ++++++++++++++++++++
- 1 file changed, 20 insertions(+)
-
---- a/drivers/gpu/drm/vc4/vc4_drv.c
-+++ b/drivers/gpu/drm/vc4/vc4_drv.c
-@@ -164,6 +164,24 @@ static void vc4_match_add_drivers(struct
- }
- }
-
-+static void vc4_kick_out_firmware_fb(void)
-+{
-+ struct apertures_struct *ap;
-+
-+ ap = alloc_apertures(1);
-+ if (!ap)
-+ return;
-+
-+ /* Since VC4 is a UMA device, the simplefb node may have been
-+ * located anywhere in memory.
-+ */
-+ ap->ranges[0].base = 0;
-+ ap->ranges[0].size = ~0;
-+
-+ remove_conflicting_framebuffers(ap, "vc4drmfb", false);
-+ kfree(ap);
-+}
-+
- static int vc4_drm_bind(struct device *dev)
- {
- struct platform_device *pdev = to_platform_device(dev);
-@@ -208,6 +226,8 @@ static int vc4_drm_bind(struct device *d
- if (ret)
- goto gem_destroy;
-
-+ vc4_kick_out_firmware_fb();
-+
- ret = drm_dev_register(drm, 0);
- if (ret < 0)
- goto unbind_all;
diff --git a/target/linux/brcm2708/patches-4.4/0334-drm-vc4-Rename-async-to-nonblock.patch b/target/linux/brcm2708/patches-4.4/0334-drm-vc4-Rename-async-to-nonblock.patch
deleted file mode 100644
index 54dab9b..0000000
--- a/target/linux/brcm2708/patches-4.4/0334-drm-vc4-Rename-async-to-nonblock.patch
+++ /dev/null
@@ -1,45 +0,0 @@
-From 864228402f90a8aed8d7978e94f6ab020412a2ee Mon Sep 17 00:00:00 2001
-From: Maarten Lankhorst <maarten.lankhorst at linux.intel.com>
-Date: Tue, 26 Apr 2016 16:11:44 +0200
-Subject: [PATCH] drm/vc4: Rename async to nonblock.
-
-The async name is deprecated and should be changed to nonblocking.
-
-Cc: Eric Anholt <eric at anholt.net>
-Signed-off-by: Maarten Lankhorst <maarten.lankhorst at linux.intel.com>
-Signed-off-by: Daniel Vetter <daniel.vetter at ffwll.ch>
-Link: http://patchwork.freedesktop.org/patch/msgid/1461679905-30177-12-git-send-email-maarten.lankhorst@linux.intel.com
-(cherry picked from commit eb63961ba52ba545f5b7ebeeeefe1c98704e1a79)
----
- drivers/gpu/drm/vc4/vc4_kms.c | 6 +++---
- 1 file changed, 3 insertions(+), 3 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_kms.c
-+++ b/drivers/gpu/drm/vc4/vc4_kms.c
-@@ -93,7 +93,7 @@ static struct vc4_commit *commit_init(st
- * vc4_atomic_commit - commit validated state object
- * @dev: DRM device
- * @state: the driver state object
-- * @async: asynchronous commit
-+ * @nonblock: nonblocking commit
- *
- * This function commits a with drm_atomic_helper_check() pre-validated state
- * object. This can still fail when e.g. the framebuffer reservation fails. For
-@@ -104,7 +104,7 @@ static struct vc4_commit *commit_init(st
- */
- static int vc4_atomic_commit(struct drm_device *dev,
- struct drm_atomic_state *state,
-- bool async)
-+ bool nonblock)
- {
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- int ret;
-@@ -170,7 +170,7 @@ static int vc4_atomic_commit(struct drm_
- * current layout.
- */
-
-- if (async) {
-+ if (nonblock) {
- vc4_queue_seqno_cb(dev, &c->cb, wait_seqno,
- vc4_atomic_complete_commit_seqno_cb);
- } else {
diff --git a/target/linux/brcm2708/patches-4.4/0335-drm-vc4-Add-support-for-gamma-ramps.patch b/target/linux/brcm2708/patches-4.4/0335-drm-vc4-Add-support-for-gamma-ramps.patch
deleted file mode 100644
index 12bf47d..0000000
--- a/target/linux/brcm2708/patches-4.4/0335-drm-vc4-Add-support-for-gamma-ramps.patch
+++ /dev/null
@@ -1,137 +0,0 @@
-From 32416213337d69aa33e3da67df148cf68df2699b Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Thu, 31 Mar 2016 18:38:20 -0700
-Subject: [PATCH] drm/vc4: Add support for gamma ramps.
-
-We could possibly save a bit of power by not requesting gamma
-conversion when the ramp happens to be 1:1, but at least if all the
-CRTCs are off the SRAM will be disabled.
-
-This should fix brightness sliders in a lot of fullscreen games.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit e582b6c7e7f9d0b1e30e8017e4082d3a9ede3310)
----
- drivers/gpu/drm/vc4/vc4_crtc.c | 58 ++++++++++++++++++++++++++++++++++++++++++
- drivers/gpu/drm/vc4/vc4_regs.h | 6 +++++
- 2 files changed, 64 insertions(+)
-
---- a/drivers/gpu/drm/vc4/vc4_crtc.c
-+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
-@@ -49,6 +49,10 @@ struct vc4_crtc {
- /* Which HVS channel we're using for our CRTC. */
- int channel;
-
-+ u8 lut_r[256];
-+ u8 lut_g[256];
-+ u8 lut_b[256];
-+
- struct drm_pending_vblank_event *event;
- };
-
-@@ -147,6 +151,46 @@ static void vc4_crtc_destroy(struct drm_
- drm_crtc_cleanup(crtc);
- }
-
-+static void
-+vc4_crtc_lut_load(struct drm_crtc *crtc)
-+{
-+ struct drm_device *dev = crtc->dev;
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
-+ u32 i;
-+
-+ /* The LUT memory is laid out with each HVS channel in order,
-+ * each of which takes 256 writes for R, 256 for G, then 256
-+ * for B.
-+ */
-+ HVS_WRITE(SCALER_GAMADDR,
-+ SCALER_GAMADDR_AUTOINC |
-+ (vc4_crtc->channel * 3 * crtc->gamma_size));
-+
-+ for (i = 0; i < crtc->gamma_size; i++)
-+ HVS_WRITE(SCALER_GAMDATA, vc4_crtc->lut_r[i]);
-+ for (i = 0; i < crtc->gamma_size; i++)
-+ HVS_WRITE(SCALER_GAMDATA, vc4_crtc->lut_g[i]);
-+ for (i = 0; i < crtc->gamma_size; i++)
-+ HVS_WRITE(SCALER_GAMDATA, vc4_crtc->lut_b[i]);
-+}
-+
-+static void
-+vc4_crtc_gamma_set(struct drm_crtc *crtc, u16 *r, u16 *g, u16 *b,
-+ uint32_t start, uint32_t size)
-+{
-+ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
-+ u32 i;
-+
-+ for (i = start; i < start + size; i++) {
-+ vc4_crtc->lut_r[i] = r[i] >> 8;
-+ vc4_crtc->lut_g[i] = g[i] >> 8;
-+ vc4_crtc->lut_b[i] = b[i] >> 8;
-+ }
-+
-+ vc4_crtc_lut_load(crtc);
-+}
-+
- static u32 vc4_get_fifo_full_level(u32 format)
- {
- static const u32 fifo_len_bytes = 64;
-@@ -260,8 +304,14 @@ static void vc4_crtc_mode_set_nofb(struc
-
- HVS_WRITE(SCALER_DISPBKGNDX(vc4_crtc->channel),
- SCALER_DISPBKGND_AUTOHS |
-+ SCALER_DISPBKGND_GAMMA |
- (interlace ? SCALER_DISPBKGND_INTERLACE : 0));
-
-+ /* Reload the LUT, since the SRAMs would have been disabled if
-+ * all CRTCs had SCALER_DISPBKGND_GAMMA unset at once.
-+ */
-+ vc4_crtc_lut_load(crtc);
-+
- if (debug_dump_regs) {
- DRM_INFO("CRTC %d regs after:\n", drm_crtc_index(crtc));
- vc4_crtc_dump_regs(vc4_crtc);
-@@ -613,6 +663,7 @@ static const struct drm_crtc_funcs vc4_c
- .reset = drm_atomic_helper_crtc_reset,
- .atomic_duplicate_state = vc4_crtc_duplicate_state,
- .atomic_destroy_state = vc4_crtc_destroy_state,
-+ .gamma_set = vc4_crtc_gamma_set,
- };
-
- static const struct drm_crtc_helper_funcs vc4_crtc_helper_funcs = {
-@@ -731,6 +782,7 @@ static int vc4_crtc_bind(struct device *
- primary_plane->crtc = crtc;
- vc4->crtc[drm_crtc_index(crtc)] = vc4_crtc;
- vc4_crtc->channel = vc4_crtc->data->hvs_channel;
-+ drm_mode_crtc_set_gamma_size(crtc, ARRAY_SIZE(vc4_crtc->lut_r));
-
- /* Set up some arbitrary number of planes. We're not limited
- * by a set number of physical registers, just the space in
-@@ -771,6 +823,12 @@ static int vc4_crtc_bind(struct device *
-
- vc4_set_crtc_possible_masks(drm, crtc);
-
-+ for (i = 0; i < crtc->gamma_size; i++) {
-+ vc4_crtc->lut_r[i] = i;
-+ vc4_crtc->lut_g[i] = i;
-+ vc4_crtc->lut_b[i] = i;
-+ }
-+
- platform_set_drvdata(pdev, vc4_crtc);
-
- return 0;
---- a/drivers/gpu/drm/vc4/vc4_regs.h
-+++ b/drivers/gpu/drm/vc4/vc4_regs.h
-@@ -390,6 +390,12 @@
- #define SCALER_DISPBASE2 0x0000006c
- #define SCALER_DISPALPHA2 0x00000070
- #define SCALER_GAMADDR 0x00000078
-+# define SCALER_GAMADDR_AUTOINC BIT(31)
-+/* Enables all gamma ramp SRAMs, not just those of CRTCs with gamma
-+ * enabled.
-+ */
-+# define SCALER_GAMADDR_SRAMENB BIT(30)
-+
- #define SCALER_GAMDATA 0x000000e0
- #define SCALER_DLIST_START 0x00002000
- #define SCALER_DLIST_SIZE 0x00004000
diff --git a/target/linux/brcm2708/patches-4.4/0336-drm-vc4-Add-missing-render-node-support.patch b/target/linux/brcm2708/patches-4.4/0336-drm-vc4-Add-missing-render-node-support.patch
deleted file mode 100644
index ca41046..0000000
--- a/target/linux/brcm2708/patches-4.4/0336-drm-vc4-Add-missing-render-node-support.patch
+++ /dev/null
@@ -1,26 +0,0 @@
-From 18b4b5539b142af8a1733e86e30a73d7b62cb739 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Thu, 14 Apr 2016 23:16:05 -0700
-Subject: [PATCH] drm/vc4: Add missing render node support
-
-There shouldn't be any other driver support necessary, since none of
-the driver-specific ioctls ever required auth, and none of them deal
-with modesetting.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Reviewed-by: Daniel Vetter <daniel.vetter at ffwll.ch>
-(cherry picked from commit 0cd3e27476620176c19e346f82576c6e139b85a9)
----
- drivers/gpu/drm/vc4/vc4_drv.c | 1 +
- 1 file changed, 1 insertion(+)
-
---- a/drivers/gpu/drm/vc4/vc4_drv.c
-+++ b/drivers/gpu/drm/vc4/vc4_drv.c
-@@ -90,6 +90,7 @@ static struct drm_driver vc4_drm_driver
- DRIVER_ATOMIC |
- DRIVER_GEM |
- DRIVER_HAVE_IRQ |
-+ DRIVER_RENDER |
- DRIVER_PRIME),
- .lastclose = vc4_lastclose,
- .preclose = vc4_drm_preclose,
diff --git a/target/linux/brcm2708/patches-4.4/0337-drm-panel-simple-Add-the-7-DPI-panel-from-Adafruit.patch b/target/linux/brcm2708/patches-4.4/0337-drm-panel-simple-Add-the-7-DPI-panel-from-Adafruit.patch
deleted file mode 100644
index 3aac13b..0000000
--- a/target/linux/brcm2708/patches-4.4/0337-drm-panel-simple-Add-the-7-DPI-panel-from-Adafruit.patch
+++ /dev/null
@@ -1,86 +0,0 @@
-From e2bcafd4dbc3f179adbd6dd60c700994bd641799 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Thu, 24 Mar 2016 17:23:48 -0700
-Subject: [PATCH] drm/panel: simple: Add the 7" DPI panel from Adafruit
-
-This is a basic TFT panel with a 40-pin FPC connector on it. The
-specification doesn't define timings, but the Adafruit instructions
-were setting up 800x480 CVT.
-
-v2: Add .bus_format and vsync/hsync flags.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Acked-by: Rob Herring <robh at kernel.org>
-[treding at nvidia.com: keep entries properly sorted]
-Signed-off-by: Thierry Reding <treding at nvidia.com>
-
-(cherry picked from commit 8070fdbd024727c752f815b18e5339c681a01bbe)
----
- .../bindings/display/panel/ontat,yx700wv03.txt | 7 ++++
- drivers/gpu/drm/panel/panel-simple.c | 37 ++++++++++++++++++++++
- 2 files changed, 44 insertions(+)
- create mode 100644 Documentation/devicetree/bindings/display/panel/ontat,yx700wv03.txt
-
---- /dev/null
-+++ b/Documentation/devicetree/bindings/display/panel/ontat,yx700wv03.txt
-@@ -0,0 +1,7 @@
-+On Tat Industrial Company 7" DPI TFT panel.
-+
-+Required properties:
-+- compatible: should be "ontat,yx700wv03"
-+
-+This binding is compatible with the simple-panel binding, which is specified
-+in simple-panel.txt in this directory.
---- a/drivers/gpu/drm/panel/panel-simple.c
-+++ b/drivers/gpu/drm/panel/panel-simple.c
-@@ -1003,6 +1003,40 @@ static const struct panel_desc okaya_rs8
- .bus_format = MEDIA_BUS_FMT_RGB666_1X18,
- };
-
-+/*
-+ * 800x480 CVT. The panel appears to be quite accepting, at least as far as
-+ * pixel clocks, but this is the timing that was being used in the Adafruit
-+ * installation instructions.
-+ */
-+static const struct drm_display_mode ontat_yx700wv03_mode = {
-+ .clock = 29500,
-+ .hdisplay = 800,
-+ .hsync_start = 824,
-+ .hsync_end = 896,
-+ .htotal = 992,
-+ .vdisplay = 480,
-+ .vsync_start = 483,
-+ .vsync_end = 493,
-+ .vtotal = 500,
-+ .vrefresh = 60,
-+ .flags = DRM_MODE_FLAG_NVSYNC | DRM_MODE_FLAG_NHSYNC,
-+};
-+
-+/*
-+ * Specification at:
-+ * https://www.adafruit.com/images/product-files/2406/c3163.pdf
-+ */
-+static const struct panel_desc ontat_yx700wv03 = {
-+ .modes = &ontat_yx700wv03_mode,
-+ .num_modes = 1,
-+ .bpc = 8,
-+ .size = {
-+ .width = 154,
-+ .height = 83,
-+ },
-+ .bus_format = MEDIA_BUS_FMT_RGB888_1X24,
-+};
-+
- static const struct drm_display_mode ortustech_com43h4m85ulc_mode = {
- .clock = 25000,
- .hdisplay = 480,
-@@ -1179,6 +1213,9 @@ static const struct of_device_id platfor
- .compatible = "okaya,rs800480t-7x0gp",
- .data = &okaya_rs800480t_7x0gp,
- }, {
-+ .compatible = "ontat,yx700wv03",
-+ .data = &ontat_yx700wv03,
-+ }, {
- .compatible = "ortustech,com43h4m85ulc",
- .data = &ortustech_com43h4m85ulc,
- }, {
diff --git a/target/linux/brcm2708/patches-4.4/0338-BCM270X_DT-Add-the-disabled-by-default-DPI-device-no.patch b/target/linux/brcm2708/patches-4.4/0338-BCM270X_DT-Add-the-disabled-by-default-DPI-device-no.patch
deleted file mode 100644
index d2cd892..0000000
--- a/target/linux/brcm2708/patches-4.4/0338-BCM270X_DT-Add-the-disabled-by-default-DPI-device-no.patch
+++ /dev/null
@@ -1,33 +0,0 @@
-From 0d67f03b11b9e2d0efdbfc05ae898d79d89c319f Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 6 May 2016 13:18:09 -0700
-Subject: [PATCH] BCM270X_DT: Add the disabled-by-default DPI device node.
-
-This will be enabled and connected to a particular panel by DT
-overlays.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- arch/arm/boot/dts/bcm2708_common.dtsi | 11 +++++++++++
- 1 file changed, 11 insertions(+)
-
---- a/arch/arm/boot/dts/bcm2708_common.dtsi
-+++ b/arch/arm/boot/dts/bcm2708_common.dtsi
-@@ -179,6 +179,17 @@
- status = "disabled";
- };
-
-+ dpi: dpi at 7e208000 {
-+ compatible = "brcm,bcm2835-dpi";
-+ reg = <0x7e208000 0x8c>;
-+ clocks = <&cprman BCM2835_CLOCK_VPU>,
-+ <&cprman BCM2835_CLOCK_DPI>;
-+ clock-names = "core", "pixel";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "disabled";
-+ };
-+
- pixelvalve1: pixelvalve at 7e207000 {
- compatible = "brcm,bcm2835-pixelvalve1";
- reg = <0x7e207000 0x100>;
diff --git a/target/linux/brcm2708/patches-4.4/0339-drm-vc4-Fix-get_vblank_counter-with-proper-no-op-for.patch b/target/linux/brcm2708/patches-4.4/0339-drm-vc4-Fix-get_vblank_counter-with-proper-no-op-for.patch
deleted file mode 100644
index fdd97bd..0000000
--- a/target/linux/brcm2708/patches-4.4/0339-drm-vc4-Fix-get_vblank_counter-with-proper-no-op-for.patch
+++ /dev/null
@@ -1,31 +0,0 @@
-From 29759cf06eed641e1337543c7f6b89d487b31f8b Mon Sep 17 00:00:00 2001
-From: Mario Kleiner <mario.kleiner.de at gmail.com>
-Date: Fri, 6 May 2016 19:26:05 +0200
-Subject: [PATCH] drm/vc4: Fix get_vblank_counter with proper no-op for Linux
- 4.4+
-
-get_vblank_counter hooked up to drm_vblank_count() which alway was
-non-sensical but didn't hurt in the past. Since Linux 4.4 it
-triggers a WARN_ON_ONCE in drm_update_vblank_count on first vblank
-irq disable, so fix it by hooking to drm_vblank_no_hw_counter().
-
-Tested against Raspian kernel 4.4.8 tree on RPi 2B.
-
-Signed-off-by: Mario Kleiner <mario.kleiner.de at gmail.com>
-Cc: Eric Anholt <eric at anholt.net>
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_drv.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/gpu/drm/vc4/vc4_drv.c
-+++ b/drivers/gpu/drm/vc4/vc4_drv.c
-@@ -102,7 +102,7 @@ static struct drm_driver vc4_drm_driver
-
- .enable_vblank = vc4_enable_vblank,
- .disable_vblank = vc4_disable_vblank,
-- .get_vblank_counter = drm_vblank_count,
-+ .get_vblank_counter = drm_vblank_no_hw_counter,
-
- #if defined(CONFIG_DEBUG_FS)
- .debugfs_init = vc4_debugfs_init,
diff --git a/target/linux/brcm2708/patches-4.4/0340-drm-vc4-Fix-drm_vblank_put-get-imbalance-in-page-fli.patch b/target/linux/brcm2708/patches-4.4/0340-drm-vc4-Fix-drm_vblank_put-get-imbalance-in-page-fli.patch
deleted file mode 100644
index eddcdfc..0000000
--- a/target/linux/brcm2708/patches-4.4/0340-drm-vc4-Fix-drm_vblank_put-get-imbalance-in-page-fli.patch
+++ /dev/null
@@ -1,47 +0,0 @@
-From fcb31481cff293291c6d3e7891da4be4a302cfd1 Mon Sep 17 00:00:00 2001
-From: Mario Kleiner <mario.kleiner.de at gmail.com>
-Date: Fri, 6 May 2016 19:26:06 +0200
-Subject: [PATCH] drm/vc4: Fix drm_vblank_put/get imbalance in page flip path.
-
-The async page flip path was missing drm_crtc_vblank_get/put
-completely. The sync flip path was missing a vblank put, so async
-flips only reported proper pageflip completion events by chance,
-and vblank irq's never turned off after a first vsync'ed page flip
-until system reboot.
-
-Tested against Raspian kernel 4.4.8 tree on RPi 2B.
-
-Signed-off-by: Mario Kleiner <mario.kleiner.de at gmail.com>
-Cc: Eric Anholt <eric at anholt.net>
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_crtc.c | 4 ++++
- 1 file changed, 4 insertions(+)
-
---- a/drivers/gpu/drm/vc4/vc4_crtc.c
-+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
-@@ -506,6 +506,7 @@ static void vc4_crtc_handle_page_flip(st
- if (vc4_crtc->event) {
- drm_crtc_send_vblank_event(crtc, vc4_crtc->event);
- vc4_crtc->event = NULL;
-+ drm_crtc_vblank_put(crtc);
- }
- spin_unlock_irqrestore(&dev->event_lock, flags);
- }
-@@ -556,6 +557,7 @@ vc4_async_page_flip_complete(struct vc4_
- spin_unlock_irqrestore(&dev->event_lock, flags);
- }
-
-+ drm_crtc_vblank_put(crtc);
- drm_framebuffer_unreference(flip_state->fb);
- kfree(flip_state);
-
-@@ -598,6 +600,8 @@ static int vc4_async_page_flip(struct dr
- return ret;
- }
-
-+ WARN_ON(drm_crtc_vblank_get(crtc) != 0);
-+
- /* Immediately update the plane's legacy fb pointer, so that later
- * modeset prep sees the state that will be present when the semaphore
- * is released.
diff --git a/target/linux/brcm2708/patches-4.4/0341-BCM270X_DT-Add-umbrella-I2C-Mux-overlay-i2c-mux.patch b/target/linux/brcm2708/patches-4.4/0341-BCM270X_DT-Add-umbrella-I2C-Mux-overlay-i2c-mux.patch
deleted file mode 100644
index 8ea61b9..0000000
--- a/target/linux/brcm2708/patches-4.4/0341-BCM270X_DT-Add-umbrella-I2C-Mux-overlay-i2c-mux.patch
+++ /dev/null
@@ -1,269 +0,0 @@
-From 8921183116514635e0a9d823d8547067f2aa82ee Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Wed, 11 May 2016 15:38:04 +0100
-Subject: [PATCH] BCM270X_DT: Add umbrella I2C Mux overlay i2c-mux
-
-This overlay supports a range of I2C multiplexers - PCA9542 (2 ports),
-PCA9545 (4 ports) and PCA9548 (8 ports).
-
-Also remove the dedicated i2c-mux-9548a overlays since it is no longer
-needed.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/overlays/Makefile | 2 +-
- arch/arm/boot/dts/overlays/README | 17 ++-
- arch/arm/boot/dts/overlays/i2c-mux-overlay.dts | 138 +++++++++++++++++++++
- .../boot/dts/overlays/i2c-mux-pca9548a-overlay.dts | 67 ----------
- 4 files changed, 152 insertions(+), 72 deletions(-)
- create mode 100644 arch/arm/boot/dts/overlays/i2c-mux-overlay.dts
- delete mode 100644 arch/arm/boot/dts/overlays/i2c-mux-pca9548a-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -34,7 +34,7 @@ dtbo-$(RPI_DT_OVERLAYS) += hy28a.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += hy28b.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c-rtc.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c-gpio.dtbo
--dtbo-$(RPI_DT_OVERLAYS) += i2c-mux-pca9548a.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += i2c-mux.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c-pwm-pca9685a.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c0-bcm2708.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c1-bcm2708.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -421,10 +421,19 @@ Params: i2c_gpio_sda GPIO use
- (default "2" = ~100kHz)
-
-
--Name: i2c-mux-pca9548a
--Info: Adds support for an NXP PCA9548A I2C multiplexer on i2c_arm
--Load: dtoverlay=i2c-mux-pca9548a,<param>=<val>
--Params: addr I2C address of PCA9548A (default 0x70)
-+Name: i2c-mux
-+Info: Adds support for a number of I2C bus multiplexers on i2c_arm
-+Load: dtoverlay=i2c-mux,<param>=<val>
-+Params: pca9542 Select the NXP PCA9542 device
-+
-+ pca9545 Select the NXP PCA9545 device
-+
-+ pca9548 Select the NXP PCA9548 device
-+
-+ addr Change I2C address of the device (default 0x70)
-+
-+
-+[ The i2c-mux-pca9548a overlay has been deleted. See i2c-mux. ]
-
-
- Name: i2c-pwm-pca9685a
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/i2c-mux-overlay.dts
-@@ -0,0 +1,138 @@
-+// Umbrella I2C Mux overlay
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/{
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&i2c_arm>;
-+ __dormant__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ pca9542: mux at 70 {
-+ compatible = "nxp,pca9542";
-+ reg = <0x70>;
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ i2c at 0 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <0>;
-+ };
-+ i2c at 1 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <1>;
-+ };
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&i2c_arm>;
-+ __dormant__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ pca9545: mux at 70 {
-+ compatible = "nxp,pca9545";
-+ reg = <0x70>;
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ i2c at 0 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <0>;
-+ };
-+ i2c at 1 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <1>;
-+ };
-+ i2c at 2 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <2>;
-+ };
-+ i2c at 3 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <3>;
-+ };
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&i2c_arm>;
-+ __dormant__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ pca9548: mux at 70 {
-+ compatible = "nxp,pca9548";
-+ reg = <0x70>;
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ i2c at 0 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <0>;
-+ };
-+ i2c at 1 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <1>;
-+ };
-+ i2c at 2 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <2>;
-+ };
-+ i2c at 3 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <3>;
-+ };
-+ i2c at 4 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <4>;
-+ };
-+ i2c at 5 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <5>;
-+ };
-+ i2c at 6 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <6>;
-+ };
-+ i2c at 7 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <7>;
-+ };
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ pca9542 = <0>, "+0";
-+ pca9545 = <0>, "+1";
-+ pca9548 = <0>, "+2";
-+
-+ addr = <&pca9545>,"reg:0",
-+ <&pca9548>,"reg:0";
-+ };
-+};
---- a/arch/arm/boot/dts/overlays/i2c-mux-pca9548a-overlay.dts
-+++ /dev/null
-@@ -1,67 +0,0 @@
--// Definitions for NXP PCA9548A I2C mux on ARM I2C bus.
--/dts-v1/;
--/plugin/;
--
--/{
-- compatible = "brcm,bcm2708";
--
-- fragment at 0 {
-- target = <&i2c_arm>;
-- __overlay__ {
-- #address-cells = <1>;
-- #size-cells = <0>;
-- status = "okay";
--
-- i2cmux: mux at 70 {
-- compatible = "nxp,pca9548";
-- reg = <0x70>;
-- #address-cells = <1>;
-- #size-cells = <0>;
--
-- i2c at 0 {
-- #address-cells = <1>;
-- #size-cells = <0>;
-- reg = <0>;
-- };
-- i2c at 1 {
-- #address-cells = <1>;
-- #size-cells = <0>;
-- reg = <1>;
-- };
-- i2c at 2 {
-- #address-cells = <1>;
-- #size-cells = <0>;
-- reg = <2>;
-- };
-- i2c at 3 {
-- #address-cells = <1>;
-- #size-cells = <0>;
-- reg = <3>;
-- };
-- i2c at 4 {
-- #address-cells = <1>;
-- #size-cells = <0>;
-- reg = <4>;
-- };
-- i2c at 5 {
-- #address-cells = <1>;
-- #size-cells = <0>;
-- reg = <5>;
-- };
-- i2c at 6 {
-- #address-cells = <1>;
-- #size-cells = <0>;
-- reg = <6>;
-- };
-- i2c at 7 {
-- #address-cells = <1>;
-- #size-cells = <0>;
-- reg = <7>;
-- };
-- };
-- };
-- };
-- __overrides__ {
-- addr = <&i2cmux>,"reg:0";
-- };
--};
diff --git a/target/linux/brcm2708/patches-4.4/0342-BCM270X_DT-Include-address-override-for-pca9542.patch b/target/linux/brcm2708/patches-4.4/0342-BCM270X_DT-Include-address-override-for-pca9542.patch
deleted file mode 100644
index 4feefe6..0000000
--- a/target/linux/brcm2708/patches-4.4/0342-BCM270X_DT-Include-address-override-for-pca9542.patch
+++ /dev/null
@@ -1,24 +0,0 @@
-From ad63bac56a66996bbacb5dff4d6598e93ea52740 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Thu, 12 May 2016 08:52:06 +0100
-Subject: [PATCH] BCM270X_DT: Include address override for pca9542
-
-Omitted from "BCM270X_DT: Add umbrella I2C Mux overlay i2c-mux".
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/overlays/i2c-mux-overlay.dts | 3 ++-
- 1 file changed, 2 insertions(+), 1 deletion(-)
-
---- a/arch/arm/boot/dts/overlays/i2c-mux-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/i2c-mux-overlay.dts
-@@ -132,7 +132,8 @@
- pca9545 = <0>, "+1";
- pca9548 = <0>, "+2";
-
-- addr = <&pca9545>,"reg:0",
-+ addr = <&pca9542>,"reg:0",
-+ <&pca9545>,"reg:0",
- <&pca9548>,"reg:0";
- };
- };
diff --git a/target/linux/brcm2708/patches-4.4/0343-BCM270X_DT-Fix-the-tinylcd35-overlay-RTC-support.patch b/target/linux/brcm2708/patches-4.4/0343-BCM270X_DT-Fix-the-tinylcd35-overlay-RTC-support.patch
deleted file mode 100644
index c94f4e0..0000000
--- a/target/linux/brcm2708/patches-4.4/0343-BCM270X_DT-Fix-the-tinylcd35-overlay-RTC-support.patch
+++ /dev/null
@@ -1,68 +0,0 @@
-From 883257ef0684a00823501a440e05f3eb24c1de73 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Thu, 12 May 2016 09:04:20 +0100
-Subject: [PATCH] BCM270X_DT: Fix the tinylcd35 overlay RTC support
-
-Now that overlay parameters are applied before the merge (a requirement
-for kernel runtime overlays) it is illegal for parameters/overrides to
-target nodes in the base DTB. Solve the problem of only enabling I2C
-when an RTC option is used by making the RTC fragments conditional,
-and including the required status="okay" within the fragments.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/overlays/tinylcd35-overlay.dts | 18 ++++++++++--------
- 1 file changed, 10 insertions(+), 8 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/tinylcd35-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/tinylcd35-overlay.dts
-@@ -132,28 +132,32 @@
-
- fragment at 5 {
- target = <&i2c1>;
-- __overlay__ {
-+ __dormant__ {
- #address-cells = <1>;
- #size-cells = <0>;
-
-+ status = "okay";
-+
- pcf8563: pcf8563 at 51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
-- status = "disabled";
-+ status = "okay";
- };
- };
- };
-
- fragment at 6 {
- target = <&i2c1>;
-- __overlay__ {
-+ __dormant__ {
- #address-cells = <1>;
- #size-cells = <0>;
-
-+ status = "okay";
-+
- ds1307: ds1307 at 68 {
- compatible = "maxim,ds1307";
- reg = <0x68>;
-- status = "disabled";
-+ status = "okay";
- };
- };
- };
-@@ -213,10 +217,8 @@
- <&tinylcd35_ts>,"interrupts:0",
- <&tinylcd35_ts>,"pendown-gpio:4";
- xohms = <&tinylcd35_ts>,"ti,x-plate-ohms;0";
-- rtc-pcf = <&i2c1>,"status",
-- <&pcf8563>,"status";
-- rtc-ds = <&i2c1>,"status",
-- <&ds1307>,"status";
-+ rtc-pcf = <0>,"=5";
-+ rtc-ds = <0>,"=6";
- keypad = <&keypad>,"status";
- };
- };
diff --git a/target/linux/brcm2708/patches-4.4/0344-clk-Allow-clocks-to-be-marked-as-CRITICAL.patch b/target/linux/brcm2708/patches-4.4/0344-clk-Allow-clocks-to-be-marked-as-CRITICAL.patch
deleted file mode 100644
index 702de5c..0000000
--- a/target/linux/brcm2708/patches-4.4/0344-clk-Allow-clocks-to-be-marked-as-CRITICAL.patch
+++ /dev/null
@@ -1,43 +0,0 @@
-From 731550c50d5e00edd555f25de0cc49a0ca564c0f Mon Sep 17 00:00:00 2001
-From: Lee Jones <lee.jones at linaro.org>
-Date: Thu, 11 Feb 2016 13:19:09 -0800
-Subject: [PATCH] clk: Allow clocks to be marked as CRITICAL
-
-Critical clocks are those which must not be gated, else undefined
-or catastrophic failure would occur. Here we have chosen to
-ensure the prepare/enable counts are correctly incremented, so as
-not to confuse users with enabled clocks with no visible users.
-
-Signed-off-by: Lee Jones <lee.jones at linaro.org>
-Signed-off-by: Michael Turquette <mturquette at baylibre.com>
-Link: lkml.kernel.org/r/1455225554-13267-2-git-send-email-mturquette at baylibre.com
-(cherry picked from commit 32b9b10961860860268961d9aad0c56a73018c37)
----
- drivers/clk/clk.c | 5 +++++
- include/linux/clk-provider.h | 1 +
- 2 files changed, 6 insertions(+)
-
---- a/drivers/clk/clk.c
-+++ b/drivers/clk/clk.c
-@@ -2466,6 +2466,11 @@ static int __clk_init(struct device *dev
- if (core->ops->init)
- core->ops->init(core->hw);
-
-+ if (core->flags & CLK_IS_CRITICAL) {
-+ clk_core_prepare(core);
-+ clk_core_enable(core);
-+ }
-+
- kref_init(&core->ref);
- out:
- clk_prepare_unlock();
---- a/include/linux/clk-provider.h
-+++ b/include/linux/clk-provider.h
-@@ -31,6 +31,7 @@
- #define CLK_SET_RATE_NO_REPARENT BIT(7) /* don't re-parent on rate change */
- #define CLK_GET_ACCURACY_NOCACHE BIT(8) /* do not use the cached clk accuracy */
- #define CLK_RECALC_NEW_RATES BIT(9) /* recalc rates after notifications */
-+#define CLK_IS_CRITICAL BIT(11) /* do not gate, ever */
-
- struct clk;
- struct clk_hw;
diff --git a/target/linux/brcm2708/patches-4.4/0345-clk-bcm2835-Mark-the-VPU-clock-as-critical.patch b/target/linux/brcm2708/patches-4.4/0345-clk-bcm2835-Mark-the-VPU-clock-as-critical.patch
deleted file mode 100644
index 4ebaacb..0000000
--- a/target/linux/brcm2708/patches-4.4/0345-clk-bcm2835-Mark-the-VPU-clock-as-critical.patch
+++ /dev/null
@@ -1,46 +0,0 @@
-From 16a3192294e1c450a9dccb2a808ea159bdbfdb9e Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 26 Apr 2016 11:44:59 -0700
-Subject: [PATCH] clk: bcm2835: Mark the VPU clock as critical
-
-The VPU clock is also the clock for our AXI bus, so we really can't
-disable it. This might have happened during boot if, for example,
-uart1 (aux_uart clock) probed and was then disabled before the other
-consumers of the VPU clock had probed.
-
-v2: Rewrite to use a .flags in bcm2835_clock_data, since other clocks
- will need this too.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/clk/bcm/clk-bcm2835.c | 5 ++++-
- 1 file changed, 4 insertions(+), 1 deletion(-)
-
---- a/drivers/clk/bcm/clk-bcm2835.c
-+++ b/drivers/clk/bcm/clk-bcm2835.c
-@@ -446,6 +446,8 @@ struct bcm2835_clock_data {
- /* Number of fractional bits in the divider */
- u32 frac_bits;
-
-+ u32 flags;
-+
- bool is_vpu_clock;
- bool is_mash_clock;
- };
-@@ -1244,7 +1246,7 @@ static struct clk *bcm2835_register_cloc
- init.parent_names = parents;
- init.num_parents = data->num_mux_parents;
- init.name = data->name;
-- init.flags = CLK_IGNORE_UNUSED;
-+ init.flags = data->flags | CLK_IGNORE_UNUSED;
-
- if (data->is_vpu_clock) {
- init.ops = &bcm2835_vpu_clock_clk_ops;
-@@ -1663,6 +1665,7 @@ static const struct bcm2835_clk_desc clk
- .div_reg = CM_VPUDIV,
- .int_bits = 12,
- .frac_bits = 8,
-+ .flags = CLK_IS_CRITICAL,
- .is_vpu_clock = true),
-
- /* clocks with per parent mux */
diff --git a/target/linux/brcm2708/patches-4.4/0346-clk-bcm2835-Mark-GPIO-clocks-enabled-at-boot-as-crit.patch b/target/linux/brcm2708/patches-4.4/0346-clk-bcm2835-Mark-GPIO-clocks-enabled-at-boot-as-crit.patch
deleted file mode 100644
index c860756..0000000
--- a/target/linux/brcm2708/patches-4.4/0346-clk-bcm2835-Mark-GPIO-clocks-enabled-at-boot-as-crit.patch
+++ /dev/null
@@ -1,54 +0,0 @@
-From c6f1ea4b22c1ce02929d8d52ac1c68f6fb1edeb9 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 9 May 2016 17:28:18 -0700
-Subject: [PATCH] clk: bcm2835: Mark GPIO clocks enabled at boot as critical.
-
-These divide off of PLLD_PER and are used for the ethernet and wifi
-PHYs source PLLs. Neither of them is currently represented by a phy
-device that would grab the clock for us.
-
-This keeps other drivers from killing the networking PHYs when they
-disable their own clocks and trigger PLLD_PER's refcount going to 0.
-
-v2: Skip marking as critical if they aren't on at boot.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/clk/bcm/clk-bcm2835.c | 13 ++++++++++++-
- 1 file changed, 12 insertions(+), 1 deletion(-)
-
---- a/drivers/clk/bcm/clk-bcm2835.c
-+++ b/drivers/clk/bcm/clk-bcm2835.c
-@@ -1248,6 +1248,15 @@ static struct clk *bcm2835_register_cloc
- init.name = data->name;
- init.flags = data->flags | CLK_IGNORE_UNUSED;
-
-+ /*
-+ * Some GPIO clocks for ethernet/wifi PLLs are marked as
-+ * critical (since some platforms use them), but if the
-+ * firmware didn't have them turned on then they clearly
-+ * aren't actually critical.
-+ */
-+ if ((cprman_read(cprman, data->ctl_reg) & CM_ENABLE) == 0)
-+ init.flags &= ~CLK_IS_CRITICAL;
-+
- if (data->is_vpu_clock) {
- init.ops = &bcm2835_vpu_clock_clk_ops;
- } else {
-@@ -1722,13 +1731,15 @@ static const struct bcm2835_clk_desc clk
- .div_reg = CM_GP1DIV,
- .int_bits = 12,
- .frac_bits = 12,
-+ .flags = CLK_IS_CRITICAL,
- .is_mash_clock = true),
- [BCM2835_CLOCK_GP2] = REGISTER_PER_CLK(
- .name = "gp2",
- .ctl_reg = CM_GP2CTL,
- .div_reg = CM_GP2DIV,
- .int_bits = 12,
-- .frac_bits = 12),
-+ .frac_bits = 12,
-+ .flags = CLK_IS_CRITICAL),
-
- /* HDMI state machine */
- [BCM2835_CLOCK_HSM] = REGISTER_PER_CLK(
diff --git a/target/linux/brcm2708/patches-4.4/0347-clk-bcm2835-Skip-PLLC-clocks-when-deciding-on-a-new-.patch b/target/linux/brcm2708/patches-4.4/0347-clk-bcm2835-Skip-PLLC-clocks-when-deciding-on-a-new-.patch
deleted file mode 100644
index 9d39eca..0000000
--- a/target/linux/brcm2708/patches-4.4/0347-clk-bcm2835-Skip-PLLC-clocks-when-deciding-on-a-new-.patch
+++ /dev/null
@@ -1,71 +0,0 @@
-From 298433024e7f889e87a002f3888bcd5ab8a319cb Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 26 Apr 2016 12:39:45 -0700
-Subject: [PATCH] clk: bcm2835: Skip PLLC clocks when deciding on a new clock
- parent
-
-If the firmware had set up a clock to source from PLLC, go along with
-it. But if we're looking for a new parent, we don't want to switch it
-to PLLC because the firmware will force PLLC (and thus the AXI bus
-clock) to different frequencies during over-temp/under-voltage,
-without notification to Linux.
-
-On my system, this moves the Linux-enabled HDMI state machine and DSI1
-escape clock over to plld_per from pllc_per. EMMC still ends up on
-pllc_per, because the firmware had set it up to use that.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Fixes: 41691b8862e2 ("clk: bcm2835: Add support for programming the audio domain clocks")
----
- drivers/clk/bcm/clk-bcm2835.c | 23 +++++++++++++++++++++++
- 1 file changed, 23 insertions(+)
-
---- a/drivers/clk/bcm/clk-bcm2835.c
-+++ b/drivers/clk/bcm/clk-bcm2835.c
-@@ -1022,16 +1022,28 @@ static int bcm2835_clock_set_rate(struct
- return 0;
- }
-
-+static bool
-+bcm2835_clk_is_pllc(struct clk_hw *hw)
-+{
-+ if (!hw)
-+ return false;
-+
-+ return strncmp(clk_hw_get_name(hw), "pllc", 4) == 0;
-+}
-+
- static int bcm2835_clock_determine_rate(struct clk_hw *hw,
- struct clk_rate_request *req)
- {
- struct bcm2835_clock *clock = bcm2835_clock_from_hw(hw);
- struct clk_hw *parent, *best_parent = NULL;
-+ bool current_parent_is_pllc;
- unsigned long rate, best_rate = 0;
- unsigned long prate, best_prate = 0;
- size_t i;
- u32 div;
-
-+ current_parent_is_pllc = bcm2835_clk_is_pllc(clk_hw_get_parent(hw));
-+
- /*
- * Select parent clock that results in the closest but lower rate
- */
-@@ -1039,6 +1051,17 @@ static int bcm2835_clock_determine_rate(
- parent = clk_hw_get_parent_by_index(hw, i);
- if (!parent)
- continue;
-+
-+ /*
-+ * Don't choose a PLLC-derived clock as our parent
-+ * unless it had been manually set that way. PLLC's
-+ * frequency gets adjusted by the firmware due to
-+ * over-temp or under-voltage conditions, without
-+ * prior notification to our clock consumer.
-+ */
-+ if (bcm2835_clk_is_pllc(parent) && !current_parent_is_pllc)
-+ continue;
-+
- prate = clk_hw_get_rate(parent);
- div = bcm2835_clock_choose_div(hw, req->rate, prate, true);
- rate = bcm2835_clock_rate_from_divisor(clock, prate, div);
diff --git a/target/linux/brcm2708/patches-4.4/0348-mmc-Add-MMC_QUIRK_ERASE_BROKEN-for-some-cards.patch b/target/linux/brcm2708/patches-4.4/0348-mmc-Add-MMC_QUIRK_ERASE_BROKEN-for-some-cards.patch
deleted file mode 100644
index b322f40..0000000
--- a/target/linux/brcm2708/patches-4.4/0348-mmc-Add-MMC_QUIRK_ERASE_BROKEN-for-some-cards.patch
+++ /dev/null
@@ -1,56 +0,0 @@
-From 1aa7ba68d3a693ca2420d7452b172b075b30aee6 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Wed, 11 May 2016 12:50:33 +0100
-Subject: [PATCH] mmc: Add MMC_QUIRK_ERASE_BROKEN for some cards
-
-Some SD cards have been found that corrupt data when small blocks
-are erased. Add a quirk to indicate that ERASE should not be used,
-and set it for cards of that type.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- drivers/mmc/card/block.c | 7 +++++++
- drivers/mmc/core/core.c | 3 ++-
- include/linux/mmc/card.h | 3 +++
- 3 files changed, 12 insertions(+), 1 deletion(-)
-
---- a/drivers/mmc/card/block.c
-+++ b/drivers/mmc/card/block.c
-@@ -2553,6 +2553,13 @@ static const struct mmc_fixup blk_fixups
- MMC_FIXUP("V10016", CID_MANFID_KINGSTON, CID_OEMID_ANY, add_quirk_mmc,
- MMC_QUIRK_TRIM_BROKEN),
-
-+ /*
-+ * On some Kingston SD cards, multiple erases of less than 64
-+ * sectors can cause corruption.
-+ */
-+ MMC_FIXUP("SD16G", 0x41, 0x3432, add_quirk_mmc,
-+ MMC_QUIRK_ERASE_BROKEN),
-+
- END_FIXUP
- };
-
---- a/drivers/mmc/core/core.c
-+++ b/drivers/mmc/core/core.c
-@@ -2253,7 +2253,8 @@ EXPORT_SYMBOL(mmc_erase);
- int mmc_can_erase(struct mmc_card *card)
- {
- if ((card->host->caps & MMC_CAP_ERASE) &&
-- (card->csd.cmdclass & CCC_ERASE) && card->erase_size)
-+ (card->csd.cmdclass & CCC_ERASE) && card->erase_size &&
-+ !(card->quirks & MMC_QUIRK_ERASE_BROKEN))
- return 1;
- return 0;
- }
---- a/include/linux/mmc/card.h
-+++ b/include/linux/mmc/card.h
-@@ -281,6 +281,9 @@ struct mmc_card {
- #define MMC_QUIRK_TRIM_BROKEN (1<<12) /* Skip trim */
-
-
-+#define MMC_QUIRK_ERASE_BROKEN (1<<31) /* Skip erase */
-+
-+
- unsigned int erase_size; /* erase size in sectors */
- unsigned int erase_shift; /* if erase unit is power 2 */
- unsigned int pref_erase; /* in sectors */
diff --git a/target/linux/brcm2708/patches-4.4/0349-New-AudioInjector.net-Pi-soundcard-with-low-jitter-a.patch b/target/linux/brcm2708/patches-4.4/0349-New-AudioInjector.net-Pi-soundcard-with-low-jitter-a.patch
deleted file mode 100644
index e21dd6d..0000000
--- a/target/linux/brcm2708/patches-4.4/0349-New-AudioInjector.net-Pi-soundcard-with-low-jitter-a.patch
+++ /dev/null
@@ -1,284 +0,0 @@
-From 97944f92806c9dca3bbfe76e9043b0c56bdd4849 Mon Sep 17 00:00:00 2001
-From: Matt Flax <flatmax at flatmax.org>
-Date: Mon, 16 May 2016 21:36:31 +1000
-Subject: [PATCH] New AudioInjector.net Pi soundcard with low jitter audio in
- and out.
-
-Contains the sound/soc/bcm ALSA machine driver and necessary alterations to the Kconfig and Makefile.
-Adds the dts overlay and updates the Makefile and README.
-Updates the relevant defconfig files to enable building for the Raspberry Pi.
-Thanks to Phil Elwell (pelwell) for the review, simple-card concepts and discussion. Thanks to Clive Messer for overlay naming suggestions.
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 6 +
- .../audioinjector-wm8731-audio-overlay.dts | 39 ++++++
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- sound/soc/bcm/Kconfig | 7 +
- sound/soc/bcm/Makefile | 3 +
- sound/soc/bcm/audioinjector-pi-soundcard.c | 142 +++++++++++++++++++++
- 8 files changed, 200 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/audioinjector-wm8731-audio-overlay.dts
- create mode 100644 sound/soc/bcm/audioinjector-pi-soundcard.c
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -16,6 +16,7 @@ dtbo-$(RPI_DT_OVERLAYS) += adau1977-adc.
- dtbo-$(RPI_DT_OVERLAYS) += ads7846.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += akkordion-iqdacplus.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += at86rf233.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += audioinjector-wm8731-audio.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += bmp085_i2c-sensor.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += boomberry-dac.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += boomberry-digi.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -225,6 +225,12 @@ Params: interrupt GPIO use
- arrays (0=+0pF, 15=+4.5pF, default 15)
-
-
-+Name: audioinjector-wm8731-audio
-+Info: Configures the audioinjector.net audio add on soundcard
-+Load: dtoverlay=audioinjector-wm8731-audio
-+Params: <None>
-+
-+
- Name: bmp085_i2c-sensor
- Info: Configures the BMP085/BMP180 digital barometric pressure and temperature
- sensors from Bosch Sensortec
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/audioinjector-wm8731-audio-overlay.dts
-@@ -0,0 +1,39 @@
-+// Definitions for audioinjector.net audio add on soundcard
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&i2s>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&i2c1>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ wm8731 at 1a {
-+ #sound-dai-cells = <0>;
-+ compatible = "wlf,wm8731";
-+ reg = <0x1a>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&sound>;
-+ __overlay__ {
-+ compatible = "ai,audioinjector-pi-soundcard";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
-+};
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -863,6 +863,7 @@ CONFIG_SND_BCM2708_SOC_BOOMBERRY_DAC=m
- CONFIG_SND_BCM2708_SOC_BOOMBERRY_DIGI=m
- CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC=m
- CONFIG_SND_BCM2708_SOC_RASPIDAC3=m
-+CONFIG_SND_AUDIOINJECTOR_PI_SOUNDCARD=m
- CONFIG_SND_BCM2708_SOC_ADAU1977_ADC=m
- CONFIG_SND_SOC_ADAU1701=m
- CONFIG_SND_SOC_WM8804_I2C=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -855,6 +855,7 @@ CONFIG_SND_BCM2708_SOC_BOOMBERRY_DAC=m
- CONFIG_SND_BCM2708_SOC_BOOMBERRY_DIGI=m
- CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC=m
- CONFIG_SND_BCM2708_SOC_RASPIDAC3=m
-+CONFIG_SND_AUDIOINJECTOR_PI_SOUNDCARD=m
- CONFIG_SND_BCM2708_SOC_ADAU1977_ADC=m
- CONFIG_SND_SOC_ADAU1701=m
- CONFIG_SND_SOC_WM8804_I2C=m
---- a/sound/soc/bcm/Kconfig
-+++ b/sound/soc/bcm/Kconfig
-@@ -85,3 +85,10 @@ config SND_BCM2708_SOC_ADAU1977_ADC
- select SND_SOC_ADAU1977_I2C
- help
- Say Y or M if you want to add support for ADAU1977 ADC.
-+
-+config SND_AUDIOINJECTOR_PI_SOUNDCARD
-+ tristate "Support for audioinjector.net Pi add on soundcard"
-+ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
-+ select SND_SOC_WM8731
-+ help
-+ Say Y or M if you want to add support for audioinjector.net Pi Hat
---- a/sound/soc/bcm/Makefile
-+++ b/sound/soc/bcm/Makefile
-@@ -15,6 +15,7 @@ snd-soc-rpi-dac-objs := rpi-dac.o
- snd-soc-rpi-proto-objs := rpi-proto.o
- snd-soc-iqaudio-dac-objs := iqaudio-dac.o
- snd-soc-raspidac3-objs := raspidac3.o
-+snd-soc-audioinjector-pi-soundcard-objs := audioinjector-pi-soundcard.o
-
- obj-$(CONFIG_SND_BCM2708_SOC_ADAU1977_ADC) += snd-soc-adau1977-adc.o
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DAC) += snd-soc-hifiberry-dac.o
-@@ -27,3 +28,5 @@ obj-$(CONFIG_SND_BCM2708_SOC_RPI_DAC) +=
- obj-$(CONFIG_SND_BCM2708_SOC_RPI_PROTO) += snd-soc-rpi-proto.o
- obj-$(CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC) += snd-soc-iqaudio-dac.o
- obj-$(CONFIG_SND_BCM2708_SOC_RASPIDAC3) += snd-soc-raspidac3.o
-+obj-$(CONFIG_SND_AUDIOINJECTOR_PI_SOUNDCARD) += snd-soc-audioinjector-pi-soundcard.o
-+
---- /dev/null
-+++ b/sound/soc/bcm/audioinjector-pi-soundcard.c
-@@ -0,0 +1,142 @@
-+/*
-+ * ASoC Driver for AudioInjector Pi add on soundcard
-+ *
-+ * Created on: 13-May-2016
-+ * Author: flatmax at flatmax.org
-+ * based on code by Cliff Cai <Cliff.Cai at analog.com> for the ssm2602 machine blackfin.
-+ * with help from Lars-Peter Clausen for simplifying the original code to use the dai_fmt field.
-+ * i2s_node code taken from the other sound/soc/bcm machine drivers.
-+ *
-+ * Copyright (C) 2016 Flatmax Pty. Ltd.
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * version 2 as published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful, but
-+ * WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
-+ * General Public License for more details.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/types.h>
-+
-+#include <sound/core.h>
-+#include <sound/soc.h>
-+#include <sound/pcm_params.h>
-+#include <sound/control.h>
-+
-+#include "../codecs/wm8731.h"
-+
-+static int audioinjector_pi_soundcard_dai_init(struct snd_soc_pcm_runtime *rtd)
-+{
-+ struct snd_soc_dapm_context *dapm = &rtd->card->dapm;
-+
-+ // not connected
-+ snd_soc_dapm_nc_pin(dapm, "Mic Bias");
-+ snd_soc_dapm_nc_pin(dapm, "MICIN");
-+ snd_soc_dapm_nc_pin(dapm, "RHPOUT");
-+ snd_soc_dapm_nc_pin(dapm, "LHPOUT");
-+
-+ return snd_soc_dai_set_sysclk(rtd->codec_dai, WM8731_SYSCLK_XTAL, 12000000, SND_SOC_CLOCK_IN);
-+}
-+
-+static struct snd_soc_dai_link audioinjector_pi_soundcard_dai[] = {
-+ {
-+ .name = "AudioInjector audio",
-+ .stream_name = "AudioInjector audio",
-+ .cpu_dai_name = "bcm2708-i2s.0",
-+ .codec_dai_name = "wm8731-hifi",
-+ .platform_name = "bcm2835-i2s.0",
-+ .codec_name = "wm8731.1-001a",
-+ .init = audioinjector_pi_soundcard_dai_init,
-+ .dai_fmt = SND_SOC_DAIFMT_CBM_CFM|SND_SOC_DAIFMT_I2S|SND_SOC_DAIFMT_NB_NF,
-+ },
-+};
-+
-+static const struct snd_soc_dapm_widget wm8731_dapm_widgets[] = {
-+ SND_SOC_DAPM_SPK("Ext Spk", NULL),
-+ SND_SOC_DAPM_LINE("Line In Jacks", NULL),
-+};
-+
-+/* Corgi machine connections to the codec pins */
-+static const struct snd_soc_dapm_route audioinjector_audio_map[] = {
-+ /* speaker connected to LOUT, ROUT */
-+ {"Ext Spk", NULL, "ROUT"},
-+ {"Ext Spk", NULL, "LOUT"},
-+
-+ /* line inputs */
-+ {"Line In Jacks", NULL, "Line Input"},
-+};
-+
-+static struct snd_soc_card snd_soc_audioinjector = {
-+ .name = "audioinjector-pi-soundcard",
-+ .dai_link = audioinjector_pi_soundcard_dai,
-+ .num_links = 1,
-+
-+ .dapm_widgets = wm8731_dapm_widgets,
-+ .num_dapm_widgets = ARRAY_SIZE(wm8731_dapm_widgets),
-+ .dapm_routes = audioinjector_audio_map,
-+ .num_dapm_routes = ARRAY_SIZE(audioinjector_audio_map),
-+};
-+
-+static int audioinjector_pi_soundcard_probe(struct platform_device *pdev)
-+{
-+ struct snd_soc_card *card = &snd_soc_audioinjector;
-+ int ret;
-+
-+ card->dev = &pdev->dev;
-+
-+ if (pdev->dev.of_node) {
-+ struct snd_soc_dai_link *dai = &audioinjector_pi_soundcard_dai[0];
-+ struct device_node *i2s_node = of_parse_phandle(pdev->dev.of_node,
-+ "i2s-controller", 0);
-+
-+ if (i2s_node) {
-+ dai->cpu_dai_name = NULL;
-+ dai->cpu_of_node = i2s_node;
-+ dai->platform_name = NULL;
-+ dai->platform_of_node = i2s_node;
-+ } else
-+ if (!dai->cpu_of_node) {
-+ dev_err(&pdev->dev, "Property 'i2s-controller' missing or invalid\n");
-+ return -EINVAL;
-+ }
-+ }
-+
-+ if ((ret = snd_soc_register_card(card))) {
-+ dev_err(&pdev->dev, "snd_soc_register_card failed (%d)\n", ret);
-+ }
-+ return ret;
-+}
-+
-+static int audioinjector_pi_soundcard_remove(struct platform_device *pdev)
-+{
-+ struct snd_soc_card *card = platform_get_drvdata(pdev);
-+ return snd_soc_unregister_card(card);
-+
-+}
-+
-+static const struct of_device_id audioinjector_pi_soundcard_of_match[] = {
-+ { .compatible = "ai,audioinjector-pi-soundcard", },
-+ {},
-+};
-+MODULE_DEVICE_TABLE(of, audioinjector_pi_soundcard_of_match);
-+
-+static struct platform_driver audioinjector_pi_soundcard_driver = {
-+ .driver = {
-+ .name = "audioinjector-audio",
-+ .owner = THIS_MODULE,
-+ .of_match_table = audioinjector_pi_soundcard_of_match,
-+ },
-+ .probe = audioinjector_pi_soundcard_probe,
-+ .remove = audioinjector_pi_soundcard_remove,
-+};
-+
-+module_platform_driver(audioinjector_pi_soundcard_driver);
-+MODULE_AUTHOR("Matt Flax <flatmax at flatmax.org>");
-+MODULE_DESCRIPTION("AudioInjector.net Pi Soundcard");
-+MODULE_LICENSE("GPL v2");
-+MODULE_ALIAS("platform:audioinjector-pi-soundcard");
-+
diff --git a/target/linux/brcm2708/patches-4.4/0350-mmc-Apply-QUIRK_BROKEN_ERASE-to-other-capacities.patch b/target/linux/brcm2708/patches-4.4/0350-mmc-Apply-QUIRK_BROKEN_ERASE-to-other-capacities.patch
deleted file mode 100644
index c0b3bdb..0000000
--- a/target/linux/brcm2708/patches-4.4/0350-mmc-Apply-QUIRK_BROKEN_ERASE-to-other-capacities.patch
+++ /dev/null
@@ -1,23 +0,0 @@
-From e26729f7e04d21d069169cf1c5f8611e2d9eba60 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Thu, 19 May 2016 14:40:28 +0100
-Subject: [PATCH] mmc: Apply QUIRK_BROKEN_ERASE to other capacities
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- drivers/mmc/card/block.c | 4 ++++
- 1 file changed, 4 insertions(+)
-
---- a/drivers/mmc/card/block.c
-+++ b/drivers/mmc/card/block.c
-@@ -2559,6 +2559,10 @@ static const struct mmc_fixup blk_fixups
- */
- MMC_FIXUP("SD16G", 0x41, 0x3432, add_quirk_mmc,
- MMC_QUIRK_ERASE_BROKEN),
-+ MMC_FIXUP("SD32G", 0x41, 0x3432, add_quirk_mmc,
-+ MMC_QUIRK_ERASE_BROKEN),
-+ MMC_FIXUP("SD64G", 0x41, 0x3432, add_quirk_mmc,
-+ MMC_QUIRK_ERASE_BROKEN),
-
- END_FIXUP
- };
diff --git a/target/linux/brcm2708/patches-4.4/0351-mmc-Add-card_quirks-module-parameter-log-quirks.patch b/target/linux/brcm2708/patches-4.4/0351-mmc-Add-card_quirks-module-parameter-log-quirks.patch
deleted file mode 100644
index 2604eb5..0000000
--- a/target/linux/brcm2708/patches-4.4/0351-mmc-Add-card_quirks-module-parameter-log-quirks.patch
+++ /dev/null
@@ -1,76 +0,0 @@
-From 1e3041d55d7184e94174f0a5eeaa2c23ca9d940a Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 20 May 2016 10:11:43 +0100
-Subject: [PATCH] mmc: Add card_quirks module parameter, log quirks
-
-Use mmc_block.card_quirks to override the quirks for all SD or MMC
-cards. The value is a bitfield using the bit positions defined in
-include/linux/mmc/card.h. If the module parameter is placed in the
-kernel command line (or bootargs) stored on the card then, assuming the
-device only has one SD card interface, the override effectively becomes
-card-specific.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- drivers/mmc/card/block.c | 28 +++++++++++++++++++++++++---
- 1 file changed, 25 insertions(+), 3 deletions(-)
-
---- a/drivers/mmc/card/block.c
-+++ b/drivers/mmc/card/block.c
-@@ -137,6 +137,13 @@ enum {
- module_param(perdev_minors, int, 0444);
- MODULE_PARM_DESC(perdev_minors, "Minors numbers to allocate per device");
-
-+/*
-+ * Allow quirks to be overridden for the current card
-+ */
-+static char *card_quirks;
-+module_param(card_quirks, charp, 0644);
-+MODULE_PARM_DESC(card_quirks, "Force the use of the indicated quirks (a bitfield)");
-+
- static inline int mmc_blk_part_switch(struct mmc_card *card,
- struct mmc_blk_data *md);
- static int get_card_status(struct mmc_card *card, u32 *status, int retries);
-@@ -2571,6 +2578,7 @@ static int mmc_blk_probe(struct mmc_card
- {
- struct mmc_blk_data *md, *part_md;
- char cap_str[10];
-+ char quirk_str[24];
-
- /*
- * Check that the card supports the command class(es) we need.
-@@ -2578,7 +2586,16 @@ static int mmc_blk_probe(struct mmc_card
- if (!(card->csd.cmdclass & CCC_BLOCK_READ))
- return -ENODEV;
-
-- mmc_fixup_device(card, blk_fixups);
-+ if (card_quirks) {
-+ unsigned long quirks;
-+ if (kstrtoul(card_quirks, 0, &quirks) == 0)
-+ card->quirks = (unsigned int)quirks;
-+ else
-+ pr_err("mmc_block: Invalid card_quirks parameter '%s'\n",
-+ card_quirks);
-+ }
-+ else
-+ mmc_fixup_device(card, blk_fixups);
-
- md = mmc_blk_alloc(card);
- if (IS_ERR(md))
-@@ -2586,9 +2603,14 @@ static int mmc_blk_probe(struct mmc_card
-
- string_get_size((u64)get_capacity(md->disk), 512, STRING_UNITS_2,
- cap_str, sizeof(cap_str));
-- pr_info("%s: %s %s %s %s\n",
-+ if (card->quirks)
-+ snprintf(quirk_str, sizeof(quirk_str),
-+ " (quirks 0x%08x)", card->quirks);
-+ else
-+ quirk_str[0] = '\0';
-+ pr_info("%s: %s %s %s%s%s\n",
- md->disk->disk_name, mmc_card_id(card), mmc_card_name(card),
-- cap_str, md->read_only ? "(ro)" : "");
-+ cap_str, md->read_only ? " (ro)" : "", quirk_str);
-
- if (mmc_blk_alloc_parts(card, md))
- goto out;
diff --git a/target/linux/brcm2708/patches-4.4/0352-rtc-ds1307-ensure-that-any-pending-alarm-is-cleared-.patch b/target/linux/brcm2708/patches-4.4/0352-rtc-ds1307-ensure-that-any-pending-alarm-is-cleared-.patch
deleted file mode 100644
index 5e1c338..0000000
--- a/target/linux/brcm2708/patches-4.4/0352-rtc-ds1307-ensure-that-any-pending-alarm-is-cleared-.patch
+++ /dev/null
@@ -1,58 +0,0 @@
-From 4821969ac388afa50202a3c4211a22d6ccef1fa1 Mon Sep 17 00:00:00 2001
-From: Nicolas Boullis <nboullis at debian.org>
-Date: Sun, 10 Apr 2016 13:23:05 +0200
-Subject: [PATCH] rtc: ds1307: ensure that any pending alarm is cleared before
- a new alarm is enabled
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-If a previously-set alarm was disabled and then triggered, it may still
-be pending when a new alarm is configured.
-
-Then, if the alarm is enabled before the pending alarm is cleared, then
-an interrupt is immediately raised.
-
-Unfortunately, when the alarm is cleared and enabled during the same I²C
-block write, the chip (at least the DS1339 I have) considers that the
-alarm is enabled before it is cleared, and raises an interrupt.
-
-This patch ensures that the pending alarm is cleared before the alarm is
-enabled.
-
-Signed-off-by: Nicolas Boullis <nboullis at debian.org>
-Signed-off-by: Alexandre Belloni <alexandre.belloni at free-electrons.com>
----
- drivers/rtc/rtc-ds1307.c | 13 ++++++++-----
- 1 file changed, 8 insertions(+), 5 deletions(-)
-
---- a/drivers/rtc/rtc-ds1307.c
-+++ b/drivers/rtc/rtc-ds1307.c
-@@ -540,12 +540,8 @@ static int ds1337_set_alarm(struct devic
- buf[5] = 0;
- buf[6] = 0;
-
-- /* optionally enable ALARM1 */
-+ /* disable alarms */
- buf[7] = control & ~(DS1337_BIT_A1IE | DS1337_BIT_A2IE);
-- if (t->enabled) {
-- dev_dbg(dev, "alarm IRQ armed\n");
-- buf[7] |= DS1337_BIT_A1IE; /* only ALARM1 is used */
-- }
- buf[8] = status & ~(DS1337_BIT_A1I | DS1337_BIT_A2I);
-
- ret = ds1307->write_block_data(client,
-@@ -555,6 +551,13 @@ static int ds1337_set_alarm(struct devic
- return ret;
- }
-
-+ /* optionally enable ALARM1 */
-+ if (t->enabled) {
-+ dev_dbg(dev, "alarm IRQ armed\n");
-+ buf[7] |= DS1337_BIT_A1IE; /* only ALARM1 is used */
-+ i2c_smbus_write_byte_data(client, DS1337_REG_CONTROL, buf[7]);
-+ }
-+
- return 0;
- }
-
diff --git a/target/linux/brcm2708/patches-4.4/0353-Revert-Revert-drm-vc4-Force-HDMI-to-connected.patch b/target/linux/brcm2708/patches-4.4/0353-Revert-Revert-drm-vc4-Force-HDMI-to-connected.patch
deleted file mode 100644
index 3e39a61..0000000
--- a/target/linux/brcm2708/patches-4.4/0353-Revert-Revert-drm-vc4-Force-HDMI-to-connected.patch
+++ /dev/null
@@ -1,27 +0,0 @@
-From 63d5cb4410a81b35357741efed82ea17b9d3673d Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Mon, 23 May 2016 17:06:08 +0100
-Subject: [PATCH] Revert "Revert "drm/vc4: Force HDMI to connected.""
-
-This reverts commit 7da44d06540b4a191ecc74e943f3203577fce0df.
-
-This breaks the driver on Pi3 as hotplug is implemented through a
-gpio expander owned by the GPU.
-
-We need to extend the virtual gpio driver to support this, but for
-now assume hotplug is always enabled.
----
- drivers/gpu/drm/vc4/vc4_hdmi.c | 2 ++
- 1 file changed, 2 insertions(+)
-
---- a/drivers/gpu/drm/vc4/vc4_hdmi.c
-+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
-@@ -166,6 +166,8 @@ vc4_hdmi_connector_detect(struct drm_con
- struct drm_device *dev = connector->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
-
-+ return connector_status_connected;
-+
- if (vc4->hdmi->hpd_gpio) {
- if (gpio_get_value_cansleep(vc4->hdmi->hpd_gpio) ^
- vc4->hdmi->hpd_active_low)
diff --git a/target/linux/brcm2708/patches-4.4/0354-config-Add-NF_MATCH_RPFILTER.patch b/target/linux/brcm2708/patches-4.4/0354-config-Add-NF_MATCH_RPFILTER.patch
deleted file mode 100644
index a5cafe6..0000000
--- a/target/linux/brcm2708/patches-4.4/0354-config-Add-NF_MATCH_RPFILTER.patch
+++ /dev/null
@@ -1,46 +0,0 @@
-From b823dd079c0a8f9eb9d5495a7bdbb9413d10fba4 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Mon, 23 May 2016 18:22:52 +0100
-Subject: [PATCH] config: Add NF_MATCH_RPFILTER
-
----
- arch/arm/configs/bcm2709_defconfig | 2 ++
- arch/arm/configs/bcmrpi_defconfig | 2 ++
- 2 files changed, 4 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -223,6 +223,7 @@ CONFIG_NF_CONNTRACK_IPV4=m
- CONFIG_IP_NF_IPTABLES=m
- CONFIG_IP_NF_MATCH_AH=m
- CONFIG_IP_NF_MATCH_ECN=m
-+CONFIG_IP_NF_MATCH_RPFILTER=m
- CONFIG_IP_NF_MATCH_TTL=m
- CONFIG_IP_NF_FILTER=m
- CONFIG_IP_NF_TARGET_REJECT=m
-@@ -247,6 +248,7 @@ CONFIG_IP6_NF_MATCH_OPTS=m
- CONFIG_IP6_NF_MATCH_HL=m
- CONFIG_IP6_NF_MATCH_IPV6HEADER=m
- CONFIG_IP6_NF_MATCH_MH=m
-+CONFIG_IP6_NF_MATCH_RPFILTER=m
- CONFIG_IP6_NF_MATCH_RT=m
- CONFIG_IP6_NF_TARGET_HL=m
- CONFIG_IP6_NF_FILTER=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -216,6 +216,7 @@ CONFIG_NF_CONNTRACK_IPV4=m
- CONFIG_IP_NF_IPTABLES=m
- CONFIG_IP_NF_MATCH_AH=m
- CONFIG_IP_NF_MATCH_ECN=m
-+CONFIG_IP_NF_MATCH_RPFILTER=m
- CONFIG_IP_NF_MATCH_TTL=m
- CONFIG_IP_NF_FILTER=m
- CONFIG_IP_NF_TARGET_REJECT=m
-@@ -240,6 +241,7 @@ CONFIG_IP6_NF_MATCH_OPTS=m
- CONFIG_IP6_NF_MATCH_HL=m
- CONFIG_IP6_NF_MATCH_IPV6HEADER=m
- CONFIG_IP6_NF_MATCH_MH=m
-+CONFIG_IP6_NF_MATCH_RPFILTER=m
- CONFIG_IP6_NF_MATCH_RT=m
- CONFIG_IP6_NF_TARGET_HL=m
- CONFIG_IP6_NF_FILTER=m
diff --git a/target/linux/brcm2708/patches-4.4/0355-Added-Overlay-for-Microchip-MCP23017-I2C-gpio-expand.patch b/target/linux/brcm2708/patches-4.4/0355-Added-Overlay-for-Microchip-MCP23017-I2C-gpio-expand.patch
deleted file mode 100644
index 2082eb5..0000000
--- a/target/linux/brcm2708/patches-4.4/0355-Added-Overlay-for-Microchip-MCP23017-I2C-gpio-expand.patch
+++ /dev/null
@@ -1,86 +0,0 @@
-From 8e602f1220b75a4c72b3ce5e02567888d93614f6 Mon Sep 17 00:00:00 2001
-From: Michael Kaplan <m.kaplan at evva.com>
-Date: Tue, 24 May 2016 10:19:08 +0200
-Subject: [PATCH] Added Overlay for Microchip MCP23017 I2C gpio expander
-
----
- arch/arm/boot/dts/overlays/README | 9 +++++
- arch/arm/boot/dts/overlays/mcp23017-overlay.dts | 54 +++++++++++++++++++++++++
- 2 files changed, 63 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/mcp23017-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -567,6 +567,15 @@ Params: gpio_out_pin GPIO for
- (default "off")
-
-
-+Name: mcp23017
-+Info: Configures the MCP23017 I2C port expander
-+Load: dtoverlay=mcp23017,<param>=<val>
-+Params: gpiopin Gpio pin connected to the INTA output of the
-+ MCP23017 (default: 4)
-+
-+ addr I2C address of the MCP23017 (default: 0x20)
-+
-+
- Name: mcp2515-can0
- Info: Configures the MCP2515 CAN controller on spi0.0
- Load: dtoverlay=mcp2515-can0,<param>=<val>
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/mcp23017-overlay.dts
-@@ -0,0 +1,54 @@
-+// Definitions for MCP23017 Gpio Extender from Microchip Semiconductor
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&i2c1>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ mcp23017_pins: mcp23017_pins {
-+ brcm,pins = <4>;
-+ brcm,function = <0>;
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&i2c1>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ mcp23017: mcp at 20 {
-+ compatible = "microchip,mcp23017";
-+ reg = <0x20>;
-+ gpio-controller;
-+ #gpio-cells = <2>;
-+ #interrupt-cells=<2>;
-+ interrupt-parent = <&gpio>;
-+ interrupts = <4 2>;
-+ interrupt-controller;
-+ microchip,irq-mirror;
-+
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ gpiopin = <&mcp23017_pins>,"brcm,pins:0",
-+ <&mcp23017>,"interrupts:0";
-+ addr = <&mcp23017>,"reg:0";
-+ };
-+};
-+
diff --git a/target/linux/brcm2708/patches-4.4/0362-bcm2835-camera-Fix-max-min-error-when-looping-over-c.patch b/target/linux/brcm2708/patches-4.4/0362-bcm2835-camera-Fix-max-min-error-when-looping-over-c.patch
deleted file mode 100644
index 2d461bd..0000000
--- a/target/linux/brcm2708/patches-4.4/0362-bcm2835-camera-Fix-max-min-error-when-looping-over-c.patch
+++ /dev/null
@@ -1,24 +0,0 @@
-From 5babc366b2f0386103bac6ecfb9e1bfbbf817135 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Tue, 24 May 2016 16:20:09 +0100
-Subject: [PATCH] bcm2835-camera: Fix max/min error when looping over
- cameras/resolutions
-
-See: https://github.com/raspberrypi/linux/issues/1447#issuecomment-221303506
----
- drivers/media/platform/bcm2835/bcm2835-camera.c | 4 ++--
- 1 file changed, 2 insertions(+), 2 deletions(-)
-
---- a/drivers/media/platform/bcm2835/bcm2835-camera.c
-+++ b/drivers/media/platform/bcm2835/bcm2835-camera.c
-@@ -1530,8 +1530,8 @@ static int get_num_cameras(struct vchiq_
- }
- for (i = 0;
- i < (cam_info.num_cameras > num_resolutions ?
-- cam_info.num_cameras :
-- num_resolutions);
-+ num_resolutions :
-+ cam_info.num_cameras);
- i++) {
- resolutions[i][0] = cam_info.cameras[i].max_width;
- resolutions[i][1] = cam_info.cameras[i].max_height;
diff --git a/target/linux/brcm2708/patches-4.4/0363-Change-BoomBerry-name-to-JustBoom-in-all-locations-d.patch b/target/linux/brcm2708/patches-4.4/0363-Change-BoomBerry-name-to-JustBoom-in-all-locations-d.patch
deleted file mode 100644
index 0a5f9ff..0000000
--- a/target/linux/brcm2708/patches-4.4/0363-Change-BoomBerry-name-to-JustBoom-in-all-locations-d.patch
+++ /dev/null
@@ -1,1139 +0,0 @@
-From 4a60188d596d2c98230361f9757bcf71eabc793c Mon Sep 17 00:00:00 2001
-From: Aaron Shaw <shawaj at gmail.com>
-Date: Thu, 26 May 2016 23:37:11 +0100
-Subject: [PATCH] Change BoomBerry name to JustBoom in all locations due to
- legal challenge
-
----
- arch/arm/boot/dts/overlays/Makefile | 4 +-
- arch/arm/boot/dts/overlays/README | 52 ++---
- .../boot/dts/overlays/boomberry-dac-overlay.dts | 43 -----
- .../boot/dts/overlays/boomberry-digi-overlay.dts | 39 ----
- .../arm/boot/dts/overlays/justboom-dac-overlay.dts | 43 +++++
- .../boot/dts/overlays/justboom-digi-overlay.dts | 39 ++++
- arch/arm/configs/bcm2709_defconfig | 4 +-
- arch/arm/configs/bcmrpi_defconfig | 4 +-
- sound/soc/bcm/Kconfig | 12 +-
- sound/soc/bcm/Makefile | 8 +-
- sound/soc/bcm/boomberry-dac.c | 162 ----------------
- sound/soc/bcm/boomberry-digi.c | 215 ---------------------
- sound/soc/bcm/justboom-dac.c | 162 ++++++++++++++++
- sound/soc/bcm/justboom-digi.c | 215 +++++++++++++++++++++
- 14 files changed, 501 insertions(+), 501 deletions(-)
- delete mode 100644 arch/arm/boot/dts/overlays/boomberry-dac-overlay.dts
- delete mode 100644 arch/arm/boot/dts/overlays/boomberry-digi-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/justboom-dac-overlay.dts
- create mode 100644 arch/arm/boot/dts/overlays/justboom-digi-overlay.dts
- delete mode 100644 sound/soc/bcm/boomberry-dac.c
- delete mode 100644 sound/soc/bcm/boomberry-digi.c
- create mode 100644 sound/soc/bcm/justboom-dac.c
- create mode 100644 sound/soc/bcm/justboom-digi.c
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -18,8 +18,6 @@ dtbo-$(RPI_DT_OVERLAYS) += akkordion-iqd
- dtbo-$(RPI_DT_OVERLAYS) += at86rf233.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += audioinjector-wm8731-audio.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += bmp085_i2c-sensor.dtbo
--dtbo-$(RPI_DT_OVERLAYS) += boomberry-dac.dtbo
--dtbo-$(RPI_DT_OVERLAYS) += boomberry-digi.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += dpi24.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += dwc2.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += dwc-otg.dtbo
-@@ -43,6 +41,8 @@ dtbo-$(RPI_DT_OVERLAYS) += i2s-gpio28-31
- dtbo-$(RPI_DT_OVERLAYS) += i2s-mmap.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += iqaudio-dac.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += iqaudio-dacplus.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += justboom-dac.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += justboom-digi.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += lirc-rpi.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += mcp2515-can0.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += mcp2515-can1.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -238,32 +238,6 @@ Load: dtoverlay=bmp085_i2c-sensor
- Params: <None>
-
-
--Name: boomberry-dac
--Info: Configures the BoomBerry DAC HAT, Amp HAT, DAC Zero and Amp Zero audio
-- cards
--Load: dtoverlay=boomberry-dac,<param>=<val>
--Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec
-- Digital volume control. Enable with
-- "dtoverlay=boomberry-dac,24db_digital_gain"
-- (The default behaviour is that the Digital
-- volume control is limited to a maximum of
-- 0dB. ie. it can attenuate but not provide
-- gain. For most users, this will be desired
-- as it will prevent clipping. By appending
-- the 24dB_digital_gain parameter, the Digital
-- volume control will allow up to 24dB of
-- gain. If this parameter is enabled, it is the
-- responsibility of the user to ensure that
-- the Digital volume control is set to a value
-- that does not result in clipping/distortion!)
--
--
--Name: boomberry-digi
--Info: Configures the BoomBerry Digi HAT and Digi Zero audio cards
--Load: dtoverlay=boomberry-digi
--Params: <None>
--
--
- Name: dht11
- Info: Overlay for the DHT11/DHT21/DHT22 humidity/temperature sensors
- Also sometimes found with the part number(s) AM230x.
-@@ -541,6 +515,32 @@ Params: 24db_digital_gain Allow ga
- that does not result in clipping/distortion!)
-
-
-+Name: justboom-dac
-+Info: Configures the JustBoom DAC HAT, Amp HAT, DAC Zero and Amp Zero audio
-+ cards
-+Load: dtoverlay=justboom-dac,<param>=<val>
-+Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec
-+ Digital volume control. Enable with
-+ "dtoverlay=justboom-dac,24db_digital_gain"
-+ (The default behaviour is that the Digital
-+ volume control is limited to a maximum of
-+ 0dB. ie. it can attenuate but not provide
-+ gain. For most users, this will be desired
-+ as it will prevent clipping. By appending
-+ the 24dB_digital_gain parameter, the Digital
-+ volume control will allow up to 24dB of
-+ gain. If this parameter is enabled, it is the
-+ responsibility of the user to ensure that
-+ the Digital volume control is set to a value
-+ that does not result in clipping/distortion!)
-+
-+
-+Name: justboom-digi
-+Info: Configures the JustBoom Digi HAT and Digi Zero audio cards
-+Load: dtoverlay=justboom-digi
-+Params: <None>
-+
-+
- Name: lirc-rpi
- Info: Configures lirc-rpi (Linux Infrared Remote Control for Raspberry Pi)
- Consult the module documentation for more details.
---- a/arch/arm/boot/dts/overlays/boomberry-dac-overlay.dts
-+++ /dev/null
-@@ -1,43 +0,0 @@
--// Definitions for BoomBerry DAC
--/dts-v1/;
--/plugin/;
--
--/ {
-- compatible = "brcm,bcm2708";
--
-- fragment at 0 {
-- target = <&i2s>;
-- __overlay__ {
-- status = "okay";
-- };
-- };
--
-- fragment at 1 {
-- target = <&i2c1>;
-- __overlay__ {
-- #address-cells = <1>;
-- #size-cells = <0>;
-- status = "okay";
--
-- pcm5122 at 4d {
-- #sound-dai-cells = <0>;
-- compatible = "ti,pcm5122";
-- reg = <0x4d>;
-- status = "okay";
-- };
-- };
-- };
--
-- fragment at 2 {
-- target = <&sound>;
-- frag2: __overlay__ {
-- compatible = "boomberry,boomberry-dac";
-- i2s-controller = <&i2s>;
-- status = "okay";
-- };
-- };
--
-- __overrides__ {
-- 24db_digital_gain = <&frag2>,"boomberry,24db_digital_gain?";
-- };
--};
---- a/arch/arm/boot/dts/overlays/boomberry-digi-overlay.dts
-+++ /dev/null
-@@ -1,39 +0,0 @@
--// Definitions for BoomBerry Digi
--/dts-v1/;
--/plugin/;
--
--/ {
-- compatible = "brcm,bcm2708";
--
-- fragment at 0 {
-- target = <&i2s>;
-- __overlay__ {
-- status = "okay";
-- };
-- };
--
-- fragment at 1 {
-- target = <&i2c1>;
-- __overlay__ {
-- #address-cells = <1>;
-- #size-cells = <0>;
-- status = "okay";
--
-- wm8804 at 3b {
-- #sound-dai-cells = <0>;
-- compatible = "wlf,wm8804";
-- reg = <0x3b>;
-- status = "okay";
-- };
-- };
-- };
--
-- fragment at 2 {
-- target = <&sound>;
-- __overlay__ {
-- compatible = "boomberry,boomberry-digi";
-- i2s-controller = <&i2s>;
-- status = "okay";
-- };
-- };
--};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/justboom-dac-overlay.dts
-@@ -0,0 +1,43 @@
-+// Definitions for JustBoom DAC
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&i2s>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&i2c1>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ pcm5122 at 4d {
-+ #sound-dai-cells = <0>;
-+ compatible = "ti,pcm5122";
-+ reg = <0x4d>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&sound>;
-+ frag2: __overlay__ {
-+ compatible = "justboom,justboom-dac";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
-+
-+ __overrides__ {
-+ 24db_digital_gain = <&frag2>,"justboom,24db_digital_gain?";
-+ };
-+};
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/justboom-digi-overlay.dts
-@@ -0,0 +1,39 @@
-+// Definitions for JustBoom Digi
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&i2s>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&i2c1>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ wm8804 at 3b {
-+ #sound-dai-cells = <0>;
-+ compatible = "wlf,wm8804";
-+ reg = <0x3b>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&sound>;
-+ __overlay__ {
-+ compatible = "justboom,justboom-digi";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
-+};
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -861,8 +861,8 @@ CONFIG_SND_BCM2708_SOC_HIFIBERRY_DIGI=m
- CONFIG_SND_BCM2708_SOC_HIFIBERRY_AMP=m
- CONFIG_SND_BCM2708_SOC_RPI_DAC=m
- CONFIG_SND_BCM2708_SOC_RPI_PROTO=m
--CONFIG_SND_BCM2708_SOC_BOOMBERRY_DAC=m
--CONFIG_SND_BCM2708_SOC_BOOMBERRY_DIGI=m
-+CONFIG_SND_BCM2708_SOC_JUSTBOOM_DAC=m
-+CONFIG_SND_BCM2708_SOC_JUSTBOOM_DIGI=m
- CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC=m
- CONFIG_SND_BCM2708_SOC_RASPIDAC3=m
- CONFIG_SND_AUDIOINJECTOR_PI_SOUNDCARD=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -853,8 +853,8 @@ CONFIG_SND_BCM2708_SOC_HIFIBERRY_DIGI=m
- CONFIG_SND_BCM2708_SOC_HIFIBERRY_AMP=m
- CONFIG_SND_BCM2708_SOC_RPI_DAC=m
- CONFIG_SND_BCM2708_SOC_RPI_PROTO=m
--CONFIG_SND_BCM2708_SOC_BOOMBERRY_DAC=m
--CONFIG_SND_BCM2708_SOC_BOOMBERRY_DIGI=m
-+CONFIG_SND_BCM2708_SOC_JUSTBOOM_DAC=m
-+CONFIG_SND_BCM2708_SOC_JUSTBOOM_DIGI=m
- CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC=m
- CONFIG_SND_BCM2708_SOC_RASPIDAC3=m
- CONFIG_SND_AUDIOINJECTOR_PI_SOUNDCARD=m
---- a/sound/soc/bcm/Kconfig
-+++ b/sound/soc/bcm/Kconfig
-@@ -50,19 +50,19 @@ config SND_BCM2708_SOC_RPI_PROTO
- help
- Say Y or M if you want to add support for Audio Codec Board PROTO (WM8731).
-
--config SND_BCM2708_SOC_BOOMBERRY_DAC
-- tristate "Support for BoomBerry DAC"
-+config SND_BCM2708_SOC_JUSTBOOM_DAC
-+ tristate "Support for JustBoom DAC"
- depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
- select SND_SOC_PCM512x
- help
-- Say Y or M if you want to add support for BoomBerry DAC.
-+ Say Y or M if you want to add support for JustBoom DAC.
-
--config SND_BCM2708_SOC_BOOMBERRY_DIGI
-- tristate "Support for BoomBerry Digi"
-+config SND_BCM2708_SOC_JUSTBOOM_DIGI
-+ tristate "Support for JustBoom Digi"
- depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
- select SND_SOC_WM8804
- help
-- Say Y or M if you want to add support for BoomBerry Digi.
-+ Say Y or M if you want to add support for JustBoom Digi.
-
- config SND_BCM2708_SOC_IQAUDIO_DAC
- tristate "Support for IQaudIO-DAC"
---- a/sound/soc/bcm/Makefile
-+++ b/sound/soc/bcm/Makefile
-@@ -9,8 +9,8 @@ snd-soc-hifiberry-dac-objs := hifiberry_
- snd-soc-hifiberry-dacplus-objs := hifiberry_dacplus.o
- snd-soc-hifiberry-digi-objs := hifiberry_digi.o
- snd-soc-hifiberry-amp-objs := hifiberry_amp.o
--snd-soc-boomberry-dac-objs := boomberry-dac.o
--snd-soc-boomberry-digi-objs := boomberry-digi.o
-+snd-soc-justboom-dac-objs := justboom-dac.o
-+snd-soc-justboom-digi-objs := justboom-digi.o
- snd-soc-rpi-dac-objs := rpi-dac.o
- snd-soc-rpi-proto-objs := rpi-proto.o
- snd-soc-iqaudio-dac-objs := iqaudio-dac.o
-@@ -22,8 +22,8 @@ obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_D
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DACPLUS) += snd-soc-hifiberry-dacplus.o
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DIGI) += snd-soc-hifiberry-digi.o
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_AMP) += snd-soc-hifiberry-amp.o
--obj-$(CONFIG_SND_BCM2708_SOC_BOOMBERRY_DAC) += snd-soc-boomberry-dac.o
--obj-$(CONFIG_SND_BCM2708_SOC_BOOMBERRY_DIGI) += snd-soc-boomberry-digi.o
-+obj-$(CONFIG_SND_BCM2708_SOC_JUSTBOOM_DAC) += snd-soc-justboom-dac.o
-+obj-$(CONFIG_SND_BCM2708_SOC_JUSTBOOM_DIGI) += snd-soc-justboom-digi.o
- obj-$(CONFIG_SND_BCM2708_SOC_RPI_DAC) += snd-soc-rpi-dac.o
- obj-$(CONFIG_SND_BCM2708_SOC_RPI_PROTO) += snd-soc-rpi-proto.o
- obj-$(CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC) += snd-soc-iqaudio-dac.o
---- a/sound/soc/bcm/boomberry-dac.c
-+++ /dev/null
-@@ -1,162 +0,0 @@
--/*
-- * ASoC Driver for BoomBerry DAC Raspberry Pi HAT Sound Card
-- *
-- * Author: Milan Neskovic
-- * Copyright 2016
-- * based on code by Daniel Matuschek <info at crazy-audio.com>
-- * based on code by Florian Meier <florian.meier at koalo.de>
-- *
-- * This program is free software; you can redistribute it and/or
-- * modify it under the terms of the GNU General Public License
-- * version 2 as published by the Free Software Foundation.
-- *
-- * This program is distributed in the hope that it will be useful, but
-- * WITHOUT ANY WARRANTY; without even the implied warranty of
-- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
-- * General Public License for more details.
-- */
--
--#include <linux/module.h>
--#include <linux/platform_device.h>
--
--#include <sound/core.h>
--#include <sound/pcm.h>
--#include <sound/pcm_params.h>
--#include <sound/soc.h>
--#include <sound/jack.h>
--
--#include "../codecs/pcm512x.h"
--
--static bool digital_gain_0db_limit = true;
--
--static int snd_rpi_boomberry_dac_init(struct snd_soc_pcm_runtime *rtd)
--{
-- struct snd_soc_codec *codec = rtd->codec;
-- snd_soc_update_bits(codec, PCM512x_GPIO_EN, 0x08, 0x08);
-- snd_soc_update_bits(codec, PCM512x_GPIO_OUTPUT_4, 0xf, 0x02);
-- snd_soc_update_bits(codec, PCM512x_GPIO_CONTROL_1, 0x08,0x08);
--
-- if (digital_gain_0db_limit)
-- {
-- int ret;
-- struct snd_soc_card *card = rtd->card;
--
-- ret = snd_soc_limit_volume(card, "Digital Playback Volume", 207);
-- if (ret < 0)
-- dev_warn(card->dev, "Failed to set volume limit: %d\n", ret);
-- }
--
-- return 0;
--}
--
--static int snd_rpi_boomberry_dac_hw_params(struct snd_pcm_substream *substream,
-- struct snd_pcm_hw_params *params)
--{
-- struct snd_soc_pcm_runtime *rtd = substream->private_data;
-- struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
-- /*return snd_soc_dai_set_bclk_ratio(cpu_dai, 64);*/
-- unsigned int sample_bits =
-- snd_pcm_format_physical_width(params_format(params));
-- return snd_soc_dai_set_bclk_ratio(cpu_dai, sample_bits * 2);
--}
--
--static int snd_rpi_boomberry_dac_startup(struct snd_pcm_substream *substream) {
-- struct snd_soc_pcm_runtime *rtd = substream->private_data;
-- struct snd_soc_codec *codec = rtd->codec;
-- snd_soc_update_bits(codec, PCM512x_GPIO_CONTROL_1, 0x08,0x08);
-- return 0;
--}
--
--static void snd_rpi_boomberry_dac_shutdown(struct snd_pcm_substream *substream) {
-- struct snd_soc_pcm_runtime *rtd = substream->private_data;
-- struct snd_soc_codec *codec = rtd->codec;
-- snd_soc_update_bits(codec, PCM512x_GPIO_CONTROL_1, 0x08,0x00);
--}
--
--/* machine stream operations */
--static struct snd_soc_ops snd_rpi_boomberry_dac_ops = {
-- .hw_params = snd_rpi_boomberry_dac_hw_params,
-- .startup = snd_rpi_boomberry_dac_startup,
-- .shutdown = snd_rpi_boomberry_dac_shutdown,
--};
--
--static struct snd_soc_dai_link snd_rpi_boomberry_dac_dai[] = {
--{
-- .name = "BoomBerry DAC",
-- .stream_name = "BoomBerry DAC HiFi",
-- .cpu_dai_name = "bcm2708-i2s.0",
-- .codec_dai_name = "pcm512x-hifi",
-- .platform_name = "bcm2708-i2s.0",
-- .codec_name = "pcm512x.1-004d",
-- .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF |
-- SND_SOC_DAIFMT_CBS_CFS,
-- .ops = &snd_rpi_boomberry_dac_ops,
-- .init = snd_rpi_boomberry_dac_init,
--},
--};
--
--/* audio machine driver */
--static struct snd_soc_card snd_rpi_boomberry_dac = {
-- .name = "snd_rpi_boomberry_dac",
-- .owner = THIS_MODULE,
-- .dai_link = snd_rpi_boomberry_dac_dai,
-- .num_links = ARRAY_SIZE(snd_rpi_boomberry_dac_dai),
--};
--
--static int snd_rpi_boomberry_dac_probe(struct platform_device *pdev)
--{
-- int ret = 0;
--
-- snd_rpi_boomberry_dac.dev = &pdev->dev;
--
-- if (pdev->dev.of_node) {
-- struct device_node *i2s_node;
-- struct snd_soc_dai_link *dai = &snd_rpi_boomberry_dac_dai[0];
-- i2s_node = of_parse_phandle(pdev->dev.of_node,
-- "i2s-controller", 0);
--
-- if (i2s_node) {
-- dai->cpu_dai_name = NULL;
-- dai->cpu_of_node = i2s_node;
-- dai->platform_name = NULL;
-- dai->platform_of_node = i2s_node;
-- }
--
-- digital_gain_0db_limit = !of_property_read_bool(
-- pdev->dev.of_node, "boomberry,24db_digital_gain");
-- }
--
-- ret = snd_soc_register_card(&snd_rpi_boomberry_dac);
-- if (ret)
-- dev_err(&pdev->dev,
-- "snd_soc_register_card() failed: %d\n", ret);
--
-- return ret;
--}
--
--static int snd_rpi_boomberry_dac_remove(struct platform_device *pdev)
--{
-- return snd_soc_unregister_card(&snd_rpi_boomberry_dac);
--}
--
--static const struct of_device_id snd_rpi_boomberry_dac_of_match[] = {
-- { .compatible = "boomberry,boomberry-dac", },
-- {},
--};
--MODULE_DEVICE_TABLE(of, snd_rpi_boomberry_dac_of_match);
--
--static struct platform_driver snd_rpi_boomberry_dac_driver = {
-- .driver = {
-- .name = "snd-rpi-boomberry-dac",
-- .owner = THIS_MODULE,
-- .of_match_table = snd_rpi_boomberry_dac_of_match,
-- },
-- .probe = snd_rpi_boomberry_dac_probe,
-- .remove = snd_rpi_boomberry_dac_remove,
--};
--
--module_platform_driver(snd_rpi_boomberry_dac_driver);
--
--MODULE_AUTHOR("Milan Neskovic <info at boomberry.co>");
--MODULE_DESCRIPTION("ASoC Driver for BoomBerry PI DAC HAT Sound Card");
--MODULE_LICENSE("GPL v2");
---- a/sound/soc/bcm/boomberry-digi.c
-+++ /dev/null
-@@ -1,215 +0,0 @@
--/*
-- * ASoC Driver for BoomBerry Raspberry Pi Digi HAT Sound Card
-- *
-- * Author: Milan Neskovic
-- * Copyright 2016
-- * based on code by Daniel Matuschek <info at crazy-audio.com>
-- * based on code by Florian Meier <florian.meier at koalo.de>
-- *
-- * This program is free software; you can redistribute it and/or
-- * modify it under the terms of the GNU General Public License
-- * version 2 as published by the Free Software Foundation.
-- *
-- * This program is distributed in the hope that it will be useful, but
-- * WITHOUT ANY WARRANTY; without even the implied warranty of
-- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
-- * General Public License for more details.
-- */
--
--#include <linux/module.h>
--#include <linux/platform_device.h>
--
--#include <sound/core.h>
--#include <sound/pcm.h>
--#include <sound/pcm_params.h>
--#include <sound/soc.h>
--#include <sound/jack.h>
--
--#include "../codecs/wm8804.h"
--
--static int snd_rpi_boomberry_digi_init(struct snd_soc_pcm_runtime *rtd)
--{
-- struct snd_soc_codec *codec = rtd->codec;
--
-- /* enable TX output */
-- snd_soc_update_bits(codec, WM8804_PWRDN, 0x4, 0x0);
--
-- return 0;
--}
--
--static int snd_rpi_boomberry_digi_startup(struct snd_pcm_substream *substream) {
-- /* turn on digital output */
-- struct snd_soc_pcm_runtime *rtd = substream->private_data;
-- struct snd_soc_codec *codec = rtd->codec;
-- snd_soc_update_bits(codec, WM8804_PWRDN, 0x3c, 0x00);
-- return 0;
--}
--
--static void snd_rpi_boomberry_digi_shutdown(struct snd_pcm_substream *substream) {
-- /* turn off output */
-- struct snd_soc_pcm_runtime *rtd = substream->private_data;
-- struct snd_soc_codec *codec = rtd->codec;
-- snd_soc_update_bits(codec, WM8804_PWRDN, 0x3c, 0x3c);
--}
--
--static int snd_rpi_boomberry_digi_hw_params(struct snd_pcm_substream *substream,
-- struct snd_pcm_hw_params *params)
--{
-- struct snd_soc_pcm_runtime *rtd = substream->private_data;
-- struct snd_soc_dai *codec_dai = rtd->codec_dai;
-- struct snd_soc_codec *codec = rtd->codec;
-- struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
--
-- int sysclk = 27000000; /* This is fixed on this board */
--
-- long mclk_freq=0;
-- int mclk_div=1;
-- int sampling_freq=1;
--
-- int ret;
--
-- int samplerate = params_rate(params);
--
-- if (samplerate<=96000) {
-- mclk_freq=samplerate*256;
-- mclk_div=WM8804_MCLKDIV_256FS;
-- } else {
-- mclk_freq=samplerate*128;
-- mclk_div=WM8804_MCLKDIV_128FS;
-- }
--
-- switch (samplerate) {
-- case 32000:
-- sampling_freq=0x03;
-- break;
-- case 44100:
-- sampling_freq=0x00;
-- break;
-- case 48000:
-- sampling_freq=0x02;
-- break;
-- case 88200:
-- sampling_freq=0x08;
-- break;
-- case 96000:
-- sampling_freq=0x0a;
-- break;
-- case 176400:
-- sampling_freq=0x0c;
-- break;
-- case 192000:
-- sampling_freq=0x0e;
-- break;
-- default:
-- dev_err(codec->dev,
-- "Failed to set WM8804 SYSCLK, unsupported samplerate %d\n",
-- samplerate);
-- }
--
-- snd_soc_dai_set_clkdiv(codec_dai, WM8804_MCLK_DIV, mclk_div);
-- snd_soc_dai_set_pll(codec_dai, 0, 0, sysclk, mclk_freq);
--
-- ret = snd_soc_dai_set_sysclk(codec_dai, WM8804_TX_CLKSRC_PLL,
-- sysclk, SND_SOC_CLOCK_OUT);
-- if (ret < 0) {
-- dev_err(codec->dev,
-- "Failed to set WM8804 SYSCLK: %d\n", ret);
-- return ret;
-- }
--
-- /* Enable TX output */
-- snd_soc_update_bits(codec, WM8804_PWRDN, 0x4, 0x0);
--
-- /* Power on */
-- snd_soc_update_bits(codec, WM8804_PWRDN, 0x9, 0);
--
-- /* set sampling frequency status bits */
-- snd_soc_update_bits(codec, WM8804_SPDTX4, 0x0f, sampling_freq);
--
-- return snd_soc_dai_set_bclk_ratio(cpu_dai,64);
--}
--
--/* machine stream operations */
--static struct snd_soc_ops snd_rpi_boomberry_digi_ops = {
-- .hw_params = snd_rpi_boomberry_digi_hw_params,
-- .startup = snd_rpi_boomberry_digi_startup,
-- .shutdown = snd_rpi_boomberry_digi_shutdown,
--};
--
--static struct snd_soc_dai_link snd_rpi_boomberry_digi_dai[] = {
--{
-- .name = "BoomBerry Digi",
-- .stream_name = "BoomBerry Digi HiFi",
-- .cpu_dai_name = "bcm2708-i2s.0",
-- .codec_dai_name = "wm8804-spdif",
-- .platform_name = "bcm2708-i2s.0",
-- .codec_name = "wm8804.1-003b",
-- .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF |
-- SND_SOC_DAIFMT_CBM_CFM,
-- .ops = &snd_rpi_boomberry_digi_ops,
-- .init = snd_rpi_boomberry_digi_init,
--},
--};
--
--/* audio machine driver */
--static struct snd_soc_card snd_rpi_boomberry_digi = {
-- .name = "snd_rpi_boomberry_digi",
-- .owner = THIS_MODULE,
-- .dai_link = snd_rpi_boomberry_digi_dai,
-- .num_links = ARRAY_SIZE(snd_rpi_boomberry_digi_dai),
--};
--
--static int snd_rpi_boomberry_digi_probe(struct platform_device *pdev)
--{
-- int ret = 0;
--
-- snd_rpi_boomberry_digi.dev = &pdev->dev;
--
-- if (pdev->dev.of_node) {
-- struct device_node *i2s_node;
-- struct snd_soc_dai_link *dai = &snd_rpi_boomberry_digi_dai[0];
-- i2s_node = of_parse_phandle(pdev->dev.of_node,
-- "i2s-controller", 0);
--
-- if (i2s_node) {
-- dai->cpu_dai_name = NULL;
-- dai->cpu_of_node = i2s_node;
-- dai->platform_name = NULL;
-- dai->platform_of_node = i2s_node;
-- }
-- }
--
-- ret = snd_soc_register_card(&snd_rpi_boomberry_digi);
-- if (ret)
-- dev_err(&pdev->dev,
-- "snd_soc_register_card() failed: %d\n", ret);
--
-- return ret;
--}
--
--static int snd_rpi_boomberry_digi_remove(struct platform_device *pdev)
--{
-- return snd_soc_unregister_card(&snd_rpi_boomberry_digi);
--}
--
--static const struct of_device_id snd_rpi_boomberry_digi_of_match[] = {
-- { .compatible = "boomberry,boomberry-digi", },
-- {},
--};
--MODULE_DEVICE_TABLE(of, snd_rpi_boomberry_digi_of_match);
--
--static struct platform_driver snd_rpi_boomberry_digi_driver = {
-- .driver = {
-- .name = "snd-rpi-boomberry-digi",
-- .owner = THIS_MODULE,
-- .of_match_table = snd_rpi_boomberry_digi_of_match,
-- },
-- .probe = snd_rpi_boomberry_digi_probe,
-- .remove = snd_rpi_boomberry_digi_remove,
--};
--
--module_platform_driver(snd_rpi_boomberry_digi_driver);
--
--MODULE_AUTHOR("Milan Neskovic <info at boomberry.co>");
--MODULE_DESCRIPTION("ASoC Driver for BoomBerry PI Digi HAT Sound Card");
--MODULE_LICENSE("GPL v2");
---- /dev/null
-+++ b/sound/soc/bcm/justboom-dac.c
-@@ -0,0 +1,162 @@
-+/*
-+ * ASoC Driver for JustBoom DAC Raspberry Pi HAT Sound Card
-+ *
-+ * Author: Milan Neskovic
-+ * Copyright 2016
-+ * based on code by Daniel Matuschek <info at crazy-audio.com>
-+ * based on code by Florian Meier <florian.meier at koalo.de>
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * version 2 as published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful, but
-+ * WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
-+ * General Public License for more details.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+
-+#include <sound/core.h>
-+#include <sound/pcm.h>
-+#include <sound/pcm_params.h>
-+#include <sound/soc.h>
-+#include <sound/jack.h>
-+
-+#include "../codecs/pcm512x.h"
-+
-+static bool digital_gain_0db_limit = true;
-+
-+static int snd_rpi_justboom_dac_init(struct snd_soc_pcm_runtime *rtd)
-+{
-+ struct snd_soc_codec *codec = rtd->codec;
-+ snd_soc_update_bits(codec, PCM512x_GPIO_EN, 0x08, 0x08);
-+ snd_soc_update_bits(codec, PCM512x_GPIO_OUTPUT_4, 0xf, 0x02);
-+ snd_soc_update_bits(codec, PCM512x_GPIO_CONTROL_1, 0x08,0x08);
-+
-+ if (digital_gain_0db_limit)
-+ {
-+ int ret;
-+ struct snd_soc_card *card = rtd->card;
-+
-+ ret = snd_soc_limit_volume(card, "Digital Playback Volume", 207);
-+ if (ret < 0)
-+ dev_warn(card->dev, "Failed to set volume limit: %d\n", ret);
-+ }
-+
-+ return 0;
-+}
-+
-+static int snd_rpi_justboom_dac_hw_params(struct snd_pcm_substream *substream,
-+ struct snd_pcm_hw_params *params)
-+{
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
-+ /*return snd_soc_dai_set_bclk_ratio(cpu_dai, 64);*/
-+ unsigned int sample_bits =
-+ snd_pcm_format_physical_width(params_format(params));
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, sample_bits * 2);
-+}
-+
-+static int snd_rpi_justboom_dac_startup(struct snd_pcm_substream *substream) {
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_codec *codec = rtd->codec;
-+ snd_soc_update_bits(codec, PCM512x_GPIO_CONTROL_1, 0x08,0x08);
-+ return 0;
-+}
-+
-+static void snd_rpi_justboom_dac_shutdown(struct snd_pcm_substream *substream) {
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_codec *codec = rtd->codec;
-+ snd_soc_update_bits(codec, PCM512x_GPIO_CONTROL_1, 0x08,0x00);
-+}
-+
-+/* machine stream operations */
-+static struct snd_soc_ops snd_rpi_justboom_dac_ops = {
-+ .hw_params = snd_rpi_justboom_dac_hw_params,
-+ .startup = snd_rpi_justboom_dac_startup,
-+ .shutdown = snd_rpi_justboom_dac_shutdown,
-+};
-+
-+static struct snd_soc_dai_link snd_rpi_justboom_dac_dai[] = {
-+{
-+ .name = "JustBoom DAC",
-+ .stream_name = "JustBoom DAC HiFi",
-+ .cpu_dai_name = "bcm2708-i2s.0",
-+ .codec_dai_name = "pcm512x-hifi",
-+ .platform_name = "bcm2708-i2s.0",
-+ .codec_name = "pcm512x.1-004d",
-+ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF |
-+ SND_SOC_DAIFMT_CBS_CFS,
-+ .ops = &snd_rpi_justboom_dac_ops,
-+ .init = snd_rpi_justboom_dac_init,
-+},
-+};
-+
-+/* audio machine driver */
-+static struct snd_soc_card snd_rpi_justboom_dac = {
-+ .name = "snd_rpi_justboom_dac",
-+ .owner = THIS_MODULE,
-+ .dai_link = snd_rpi_justboom_dac_dai,
-+ .num_links = ARRAY_SIZE(snd_rpi_justboom_dac_dai),
-+};
-+
-+static int snd_rpi_justboom_dac_probe(struct platform_device *pdev)
-+{
-+ int ret = 0;
-+
-+ snd_rpi_justboom_dac.dev = &pdev->dev;
-+
-+ if (pdev->dev.of_node) {
-+ struct device_node *i2s_node;
-+ struct snd_soc_dai_link *dai = &snd_rpi_justboom_dac_dai[0];
-+ i2s_node = of_parse_phandle(pdev->dev.of_node,
-+ "i2s-controller", 0);
-+
-+ if (i2s_node) {
-+ dai->cpu_dai_name = NULL;
-+ dai->cpu_of_node = i2s_node;
-+ dai->platform_name = NULL;
-+ dai->platform_of_node = i2s_node;
-+ }
-+
-+ digital_gain_0db_limit = !of_property_read_bool(
-+ pdev->dev.of_node, "justboom,24db_digital_gain");
-+ }
-+
-+ ret = snd_soc_register_card(&snd_rpi_justboom_dac);
-+ if (ret)
-+ dev_err(&pdev->dev,
-+ "snd_soc_register_card() failed: %d\n", ret);
-+
-+ return ret;
-+}
-+
-+static int snd_rpi_justboom_dac_remove(struct platform_device *pdev)
-+{
-+ return snd_soc_unregister_card(&snd_rpi_justboom_dac);
-+}
-+
-+static const struct of_device_id snd_rpi_justboom_dac_of_match[] = {
-+ { .compatible = "justboom,justboom-dac", },
-+ {},
-+};
-+MODULE_DEVICE_TABLE(of, snd_rpi_justboom_dac_of_match);
-+
-+static struct platform_driver snd_rpi_justboom_dac_driver = {
-+ .driver = {
-+ .name = "snd-rpi-justboom-dac",
-+ .owner = THIS_MODULE,
-+ .of_match_table = snd_rpi_justboom_dac_of_match,
-+ },
-+ .probe = snd_rpi_justboom_dac_probe,
-+ .remove = snd_rpi_justboom_dac_remove,
-+};
-+
-+module_platform_driver(snd_rpi_justboom_dac_driver);
-+
-+MODULE_AUTHOR("Milan Neskovic <info at justboom.co>");
-+MODULE_DESCRIPTION("ASoC Driver for JustBoom PI DAC HAT Sound Card");
-+MODULE_LICENSE("GPL v2");
---- /dev/null
-+++ b/sound/soc/bcm/justboom-digi.c
-@@ -0,0 +1,215 @@
-+/*
-+ * ASoC Driver for JustBoom Raspberry Pi Digi HAT Sound Card
-+ *
-+ * Author: Milan Neskovic
-+ * Copyright 2016
-+ * based on code by Daniel Matuschek <info at crazy-audio.com>
-+ * based on code by Florian Meier <florian.meier at koalo.de>
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * version 2 as published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful, but
-+ * WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
-+ * General Public License for more details.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+
-+#include <sound/core.h>
-+#include <sound/pcm.h>
-+#include <sound/pcm_params.h>
-+#include <sound/soc.h>
-+#include <sound/jack.h>
-+
-+#include "../codecs/wm8804.h"
-+
-+static int snd_rpi_justboom_digi_init(struct snd_soc_pcm_runtime *rtd)
-+{
-+ struct snd_soc_codec *codec = rtd->codec;
-+
-+ /* enable TX output */
-+ snd_soc_update_bits(codec, WM8804_PWRDN, 0x4, 0x0);
-+
-+ return 0;
-+}
-+
-+static int snd_rpi_justboom_digi_startup(struct snd_pcm_substream *substream) {
-+ /* turn on digital output */
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_codec *codec = rtd->codec;
-+ snd_soc_update_bits(codec, WM8804_PWRDN, 0x3c, 0x00);
-+ return 0;
-+}
-+
-+static void snd_rpi_justboom_digi_shutdown(struct snd_pcm_substream *substream) {
-+ /* turn off output */
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_codec *codec = rtd->codec;
-+ snd_soc_update_bits(codec, WM8804_PWRDN, 0x3c, 0x3c);
-+}
-+
-+static int snd_rpi_justboom_digi_hw_params(struct snd_pcm_substream *substream,
-+ struct snd_pcm_hw_params *params)
-+{
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_dai *codec_dai = rtd->codec_dai;
-+ struct snd_soc_codec *codec = rtd->codec;
-+ struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
-+
-+ int sysclk = 27000000; /* This is fixed on this board */
-+
-+ long mclk_freq=0;
-+ int mclk_div=1;
-+ int sampling_freq=1;
-+
-+ int ret;
-+
-+ int samplerate = params_rate(params);
-+
-+ if (samplerate<=96000) {
-+ mclk_freq=samplerate*256;
-+ mclk_div=WM8804_MCLKDIV_256FS;
-+ } else {
-+ mclk_freq=samplerate*128;
-+ mclk_div=WM8804_MCLKDIV_128FS;
-+ }
-+
-+ switch (samplerate) {
-+ case 32000:
-+ sampling_freq=0x03;
-+ break;
-+ case 44100:
-+ sampling_freq=0x00;
-+ break;
-+ case 48000:
-+ sampling_freq=0x02;
-+ break;
-+ case 88200:
-+ sampling_freq=0x08;
-+ break;
-+ case 96000:
-+ sampling_freq=0x0a;
-+ break;
-+ case 176400:
-+ sampling_freq=0x0c;
-+ break;
-+ case 192000:
-+ sampling_freq=0x0e;
-+ break;
-+ default:
-+ dev_err(codec->dev,
-+ "Failed to set WM8804 SYSCLK, unsupported samplerate %d\n",
-+ samplerate);
-+ }
-+
-+ snd_soc_dai_set_clkdiv(codec_dai, WM8804_MCLK_DIV, mclk_div);
-+ snd_soc_dai_set_pll(codec_dai, 0, 0, sysclk, mclk_freq);
-+
-+ ret = snd_soc_dai_set_sysclk(codec_dai, WM8804_TX_CLKSRC_PLL,
-+ sysclk, SND_SOC_CLOCK_OUT);
-+ if (ret < 0) {
-+ dev_err(codec->dev,
-+ "Failed to set WM8804 SYSCLK: %d\n", ret);
-+ return ret;
-+ }
-+
-+ /* Enable TX output */
-+ snd_soc_update_bits(codec, WM8804_PWRDN, 0x4, 0x0);
-+
-+ /* Power on */
-+ snd_soc_update_bits(codec, WM8804_PWRDN, 0x9, 0);
-+
-+ /* set sampling frequency status bits */
-+ snd_soc_update_bits(codec, WM8804_SPDTX4, 0x0f, sampling_freq);
-+
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai,64);
-+}
-+
-+/* machine stream operations */
-+static struct snd_soc_ops snd_rpi_justboom_digi_ops = {
-+ .hw_params = snd_rpi_justboom_digi_hw_params,
-+ .startup = snd_rpi_justboom_digi_startup,
-+ .shutdown = snd_rpi_justboom_digi_shutdown,
-+};
-+
-+static struct snd_soc_dai_link snd_rpi_justboom_digi_dai[] = {
-+{
-+ .name = "JustBoom Digi",
-+ .stream_name = "JustBoom Digi HiFi",
-+ .cpu_dai_name = "bcm2708-i2s.0",
-+ .codec_dai_name = "wm8804-spdif",
-+ .platform_name = "bcm2708-i2s.0",
-+ .codec_name = "wm8804.1-003b",
-+ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF |
-+ SND_SOC_DAIFMT_CBM_CFM,
-+ .ops = &snd_rpi_justboom_digi_ops,
-+ .init = snd_rpi_justboom_digi_init,
-+},
-+};
-+
-+/* audio machine driver */
-+static struct snd_soc_card snd_rpi_justboom_digi = {
-+ .name = "snd_rpi_justboom_digi",
-+ .owner = THIS_MODULE,
-+ .dai_link = snd_rpi_justboom_digi_dai,
-+ .num_links = ARRAY_SIZE(snd_rpi_justboom_digi_dai),
-+};
-+
-+static int snd_rpi_justboom_digi_probe(struct platform_device *pdev)
-+{
-+ int ret = 0;
-+
-+ snd_rpi_justboom_digi.dev = &pdev->dev;
-+
-+ if (pdev->dev.of_node) {
-+ struct device_node *i2s_node;
-+ struct snd_soc_dai_link *dai = &snd_rpi_justboom_digi_dai[0];
-+ i2s_node = of_parse_phandle(pdev->dev.of_node,
-+ "i2s-controller", 0);
-+
-+ if (i2s_node) {
-+ dai->cpu_dai_name = NULL;
-+ dai->cpu_of_node = i2s_node;
-+ dai->platform_name = NULL;
-+ dai->platform_of_node = i2s_node;
-+ }
-+ }
-+
-+ ret = snd_soc_register_card(&snd_rpi_justboom_digi);
-+ if (ret)
-+ dev_err(&pdev->dev,
-+ "snd_soc_register_card() failed: %d\n", ret);
-+
-+ return ret;
-+}
-+
-+static int snd_rpi_justboom_digi_remove(struct platform_device *pdev)
-+{
-+ return snd_soc_unregister_card(&snd_rpi_justboom_digi);
-+}
-+
-+static const struct of_device_id snd_rpi_justboom_digi_of_match[] = {
-+ { .compatible = "justboom,justboom-digi", },
-+ {},
-+};
-+MODULE_DEVICE_TABLE(of, snd_rpi_justboom_digi_of_match);
-+
-+static struct platform_driver snd_rpi_justboom_digi_driver = {
-+ .driver = {
-+ .name = "snd-rpi-justboom-digi",
-+ .owner = THIS_MODULE,
-+ .of_match_table = snd_rpi_justboom_digi_of_match,
-+ },
-+ .probe = snd_rpi_justboom_digi_probe,
-+ .remove = snd_rpi_justboom_digi_remove,
-+};
-+
-+module_platform_driver(snd_rpi_justboom_digi_driver);
-+
-+MODULE_AUTHOR("Milan Neskovic <info at justboom.co>");
-+MODULE_DESCRIPTION("ASoC Driver for JustBoom PI Digi HAT Sound Card");
-+MODULE_LICENSE("GPL v2");
diff --git a/target/linux/brcm2708/patches-4.4/0367-Add-dt-param-to-force-HiFiBerry-DAC-Pro-into-slave-m.patch b/target/linux/brcm2708/patches-4.4/0367-Add-dt-param-to-force-HiFiBerry-DAC-Pro-into-slave-m.patch
deleted file mode 100644
index f9fc90c..0000000
--- a/target/linux/brcm2708/patches-4.4/0367-Add-dt-param-to-force-HiFiBerry-DAC-Pro-into-slave-m.patch
+++ /dev/null
@@ -1,82 +0,0 @@
-From d742437dcfd03abe608b8829b28c4871a3ce42ae Mon Sep 17 00:00:00 2001
-From: DigitalDreamtime <clive.messer at digitaldreamtime.co.uk>
-Date: Sun, 29 May 2016 05:22:29 +0100
-Subject: [PATCH] Add dt param to force HiFiBerry DAC+ Pro into slave mode
-
-"dtoverlay=hifiberry-dacplus,slave"
-
-Add 'slave' param to use HiFiBerry DAC+ Pro in slave mode,
-with Pi as master for bit and frame clock.
-
-Signed-off-by: DigitalDreamtime <clive.messer at digitaldreamtime.co.uk>
----
- arch/arm/boot/dts/overlays/README | 2 ++
- arch/arm/boot/dts/overlays/hifiberry-dacplus-overlay.dts | 6 ++++--
- sound/soc/bcm/hifiberry_dacplus.c | 10 ++++++++--
- 3 files changed, 14 insertions(+), 4 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -344,6 +344,8 @@ Params: 24db_digital_gain Allow ga
- responsibility of the user to ensure that
- the Digital volume control is set to a value
- that does not result in clipping/distortion!)
-+ slave Force DAC+ Pro into slave mode, using Pi as
-+ master for bit clock and frame clock.
-
-
- Name: hifiberry-digi
---- a/arch/arm/boot/dts/overlays/hifiberry-dacplus-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/hifiberry-dacplus-overlay.dts
-@@ -41,7 +41,7 @@
-
- fragment at 3 {
- target = <&sound>;
-- frag3: __overlay__ {
-+ hifiberry_dacplus: __overlay__ {
- compatible = "hifiberry,hifiberry-dacplus";
- i2s-controller = <&i2s>;
- status = "okay";
-@@ -49,6 +49,8 @@
- };
-
- __overrides__ {
-- 24db_digital_gain = <&frag3>,"hifiberry,24db_digital_gain?";
-+ 24db_digital_gain =
-+ <&hifiberry_dacplus>,"hifiberry,24db_digital_gain?";
-+ slave = <&hifiberry_dacplus>,"hifiberry-dacplus,slave?";
- };
- };
---- a/sound/soc/bcm/hifiberry_dacplus.c
-+++ b/sound/soc/bcm/hifiberry_dacplus.c
-@@ -47,6 +47,7 @@ struct pcm512x_priv {
- /* Clock rate of CLK48EN attached to GPIO3 pin */
- #define CLK_48EN_RATE 24576000UL
-
-+static bool slave;
- static bool snd_rpi_hifiberry_is_dacpro;
- static bool digital_gain_0db_limit = true;
-
-@@ -145,8 +146,11 @@ static int snd_rpi_hifiberry_dacplus_ini
- struct snd_soc_codec *codec = rtd->codec;
- struct pcm512x_priv *priv;
-
-- snd_rpi_hifiberry_is_dacpro
-- = snd_rpi_hifiberry_dacplus_is_pro_card(codec);
-+ if (slave)
-+ snd_rpi_hifiberry_is_dacpro = false;
-+ else
-+ snd_rpi_hifiberry_is_dacpro =
-+ snd_rpi_hifiberry_dacplus_is_pro_card(codec);
-
- if (snd_rpi_hifiberry_is_dacpro) {
- struct snd_soc_dai_link *dai = rtd->dai_link;
-@@ -314,6 +318,8 @@ static int snd_rpi_hifiberry_dacplus_pro
-
- digital_gain_0db_limit = !of_property_read_bool(
- pdev->dev.of_node, "hifiberry,24db_digital_gain");
-+ slave = of_property_read_bool(pdev->dev.of_node,
-+ "hifiberry-dacplus,slave");
- }
-
- ret = snd_soc_register_card(&snd_rpi_hifiberry_dacplus);
diff --git a/target/linux/brcm2708/patches-4.4/0368-simple-add-sound-dai-cells-to-I2S-def.patch b/target/linux/brcm2708/patches-4.4/0368-simple-add-sound-dai-cells-to-I2S-def.patch
deleted file mode 100644
index ce90ca6..0000000
--- a/target/linux/brcm2708/patches-4.4/0368-simple-add-sound-dai-cells-to-I2S-def.patch
+++ /dev/null
@@ -1,33 +0,0 @@
-From 4de668ca1f16498a6eab79af3b71e4e863333106 Mon Sep 17 00:00:00 2001
-From: DigitalDreamtime <clive.messer at digitaldreamtime.co.uk>
-Date: Thu, 19 May 2016 00:00:00 +0100
-Subject: [PATCH] simple: add sound-dai-cells to I2S def
-
-Add '#sound-dai-cells = <0>;' to the I2S definition in
-bcm2708_common.dtsi
-
-Not having it specified, whilst not causing an issue right now with
-rpi-4.4.y, is going to cause an issue going forward with the use of
-simple-card driver. So it doesn't fall through the cracks, patch it
-in now.
-
-Hopefully Martin has taken care of getting a patch submitted for the
-upstream Pi dts, as it was he who first run into the issue with the
-current upstream kernel....
-https://github.com/msperl/linux-rpi/issues/3#issue-154916615
-
-Signed-off-by: DigitalDreamtime <clive.messer at digitaldreamtime.co.uk>
----
- arch/arm/boot/dts/bcm2708_common.dtsi | 1 +
- 1 file changed, 1 insertion(+)
-
---- a/arch/arm/boot/dts/bcm2708_common.dtsi
-+++ b/arch/arm/boot/dts/bcm2708_common.dtsi
-@@ -137,6 +137,7 @@
-
- i2s: i2s at 7e203000 {
- compatible = "brcm,bcm2835-i2s";
-+ #sound-dai-cells = <0>;
- reg = <0x7e203000 0x24>,
- <0x7e101098 0x08>;
-
diff --git a/target/linux/brcm2708/patches-4.4/0369-BCM2835-V4L2-Increase-minimum-resolution-to-32x32.patch b/target/linux/brcm2708/patches-4.4/0369-BCM2835-V4L2-Increase-minimum-resolution-to-32x32.patch
deleted file mode 100644
index 3d704bb..0000000
--- a/target/linux/brcm2708/patches-4.4/0369-BCM2835-V4L2-Increase-minimum-resolution-to-32x32.patch
+++ /dev/null
@@ -1,31 +0,0 @@
-From 7ab1d91d45b4d739bacfe50b2fe89e3ac504b5ba Mon Sep 17 00:00:00 2001
-From: Dave Stevenson <6by9 at users.noreply.github.com>
-Date: Tue, 31 May 2016 10:38:31 +0100
-Subject: [PATCH] BCM2835-V4L2: Increase minimum resolution to 32x32
-
-https://github.com/raspberrypi/linux/issues/1498 showed
-up that 16x16 is failing to work on the GPU for some reason.
-
-GPU bug being tracked on
-https://github.com/raspberrypi/firmware/issues/607
-Workaround here by increasing minimum resolution via V4L2
-to 32x32.
-
-Signed-off-by: Dave Stevenson <6by9 at users.noreply.github.com>
----
- drivers/media/platform/bcm2835/bcm2835-camera.c | 4 ++--
- 1 file changed, 2 insertions(+), 2 deletions(-)
-
---- a/drivers/media/platform/bcm2835/bcm2835-camera.c
-+++ b/drivers/media/platform/bcm2835/bcm2835-camera.c
-@@ -36,8 +36,8 @@
-
- #define BM2835_MMAL_VERSION "0.0.2"
- #define BM2835_MMAL_MODULE_NAME "bcm2835-v4l2"
--#define MIN_WIDTH 16
--#define MIN_HEIGHT 16
-+#define MIN_WIDTH 32
-+#define MIN_HEIGHT 32
- #define MIN_BUFFER_SIZE (80*1024)
-
- #define MAX_VIDEO_MODE_WIDTH 1280
diff --git a/target/linux/brcm2708/patches-4.4/0370-config-Add-support-for-Logitech-Rumblepad.patch b/target/linux/brcm2708/patches-4.4/0370-config-Add-support-for-Logitech-Rumblepad.patch
deleted file mode 100644
index 7cdaf7d..0000000
--- a/target/linux/brcm2708/patches-4.4/0370-config-Add-support-for-Logitech-Rumblepad.patch
+++ /dev/null
@@ -1,36 +0,0 @@
-From 861c8462679c371acb15f780fee932fa8298d0eb Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Fri, 27 May 2016 18:23:51 +0100
-Subject: [PATCH] config: Add support for Logitech Rumblepad
-
----
- arch/arm/configs/bcm2709_defconfig | 4 ++++
- arch/arm/configs/bcmrpi_defconfig | 4 ++++
- 2 files changed, 8 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -896,6 +896,10 @@ CONFIG_HID_TWINHAN=m
- CONFIG_HID_KENSINGTON=m
- CONFIG_HID_LCPOWER=m
- CONFIG_HID_LOGITECH=m
-+CONFIG_HID_LOGITECH_DJ=m
-+CONFIG_LOGITECH_FF=y
-+CONFIG_LOGIRUMBLEPAD2_FF=y
-+CONFIG_LOGIG940_FF=y
- CONFIG_HID_MAGICMOUSE=m
- CONFIG_HID_MICROSOFT=m
- CONFIG_HID_MONTEREY=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -888,6 +888,10 @@ CONFIG_HID_TWINHAN=m
- CONFIG_HID_KENSINGTON=m
- CONFIG_HID_LCPOWER=m
- CONFIG_HID_LOGITECH=m
-+CONFIG_HID_LOGITECH_DJ=m
-+CONFIG_LOGITECH_FF=y
-+CONFIG_LOGIRUMBLEPAD2_FF=y
-+CONFIG_LOGIG940_FF=y
- CONFIG_HID_MAGICMOUSE=m
- CONFIG_HID_MICROSOFT=m
- CONFIG_HID_MONTEREY=m
diff --git a/target/linux/brcm2708/patches-4.4/0371-New-driver-for-RRA-DigiDAC1-soundcard-using-WM8741-W.patch b/target/linux/brcm2708/patches-4.4/0371-New-driver-for-RRA-DigiDAC1-soundcard-using-WM8741-W.patch
deleted file mode 100644
index c94dc55..0000000
--- a/target/linux/brcm2708/patches-4.4/0371-New-driver-for-RRA-DigiDAC1-soundcard-using-WM8741-W.patch
+++ /dev/null
@@ -1,602 +0,0 @@
-From c056c0b3563942ab9715c14fb2c4e24198f84b33 Mon Sep 17 00:00:00 2001
-From: escalator2015 <jmtasende at gmail.com>
-Date: Tue, 24 May 2016 16:20:09 +0100
-Subject: [PATCH] New driver for RRA DigiDAC1 soundcard using WM8741 + WM8804
-
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 6 +
- .../overlays/rra-digidac1-wm8741-audio-overlay.dts | 81 ++++
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- sound/soc/bcm/Kconfig | 8 +
- sound/soc/bcm/Makefile | 2 +
- sound/soc/bcm/digidac1-soundcard.c | 422 +++++++++++++++++++++
- 8 files changed, 522 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/rra-digidac1-wm8741-audio-overlay.dts
- create mode 100644 sound/soc/bcm/digidac1-soundcard.c
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -67,6 +67,7 @@ dtbo-$(RPI_DT_OVERLAYS) += rpi-display.d
- dtbo-$(RPI_DT_OVERLAYS) += rpi-ft5406.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += rpi-proto.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += rpi-sense.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += rra-digidac1-wm8741-audio.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += sdhost.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += sdio.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += sdio-1bit.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -842,6 +842,12 @@ Load: dtoverlay=rpi-sense
- Params: <None>
-
-
-+Name: rra-digidac1-wm8741-audio
-+Info: Configures the Red Rocks Audio DigiDAC1 soundcard
-+Load: dtoverlay=rra-digidac1-wm8741-audio
-+Params: <None>
-+
-+
- Name: sdhost
- Info: Selects the bcm2835-sdhost SD/MMC driver, optionally with overclock.
- N.B. This overlay is designed for situations where the mmc driver is
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/rra-digidac1-wm8741-audio-overlay.dts
-@@ -0,0 +1,81 @@
-+// Definitions for RRA DigiDAC1 Audio card
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target-path = "/";
-+ __overlay__ {
-+ aliases {
-+ ldo0 = &ldo0;
-+ ldo1 = &ldo1;
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target-path = "/soc";
-+ __overlay__ {
-+
-+ ldo1: ldo1 {
-+ compatible = "regulator-fixed";
-+ regulator-name = "DC_5V";
-+ regulator-min-microvolt = <5000000>;
-+ regulator-max-microvolt = <5000000>;
-+ regulator-always-on;
-+ };
-+
-+ ldo0: ldo0 {
-+ compatible = "regulator-fixed";
-+ regulator-name = "DC_3V3";
-+ regulator-min-microvolt = <3300000>;
-+ regulator-max-microvolt = <3300000>;
-+ regulator-always-on;
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&i2s>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 3 {
-+ target = <&i2c1>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ wm8804 at 3b {
-+ #sound-dai-cells = <0>;
-+ compatible = "wlf,wm8804";
-+ reg = <0x3b>;
-+ status = "okay";
-+ PVDD-supply = <&ldo0>;
-+ DVDD-supply = <&ldo0>;
-+ };
-+
-+ wm8742: wm8741 at 1a {
-+ compatible = "wlf,wm8741";
-+ reg = <0x1a>;
-+ status = "okay";
-+ AVDD-supply = <&ldo1>;
-+ DVDD-supply = <&ldo0>;
-+ };
-+ };
-+ };
-+
-+ fragment at 4 {
-+ target = <&sound>;
-+ __overlay__ {
-+ compatible = "rra,digidac1-soundcard";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
-+};
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -866,6 +866,7 @@ CONFIG_SND_BCM2708_SOC_JUSTBOOM_DIGI=m
- CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC=m
- CONFIG_SND_BCM2708_SOC_RASPIDAC3=m
- CONFIG_SND_AUDIOINJECTOR_PI_SOUNDCARD=m
-+CONFIG_SND_DIGIDAC1_SOUNDCARD=m
- CONFIG_SND_BCM2708_SOC_ADAU1977_ADC=m
- CONFIG_SND_SOC_ADAU1701=m
- CONFIG_SND_SOC_WM8804_I2C=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -858,6 +858,7 @@ CONFIG_SND_BCM2708_SOC_JUSTBOOM_DIGI=m
- CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC=m
- CONFIG_SND_BCM2708_SOC_RASPIDAC3=m
- CONFIG_SND_AUDIOINJECTOR_PI_SOUNDCARD=m
-+CONFIG_SND_DIGIDAC1_SOUNDCARD=m
- CONFIG_SND_BCM2708_SOC_ADAU1977_ADC=m
- CONFIG_SND_SOC_ADAU1701=m
- CONFIG_SND_SOC_WM8804_I2C=m
---- a/sound/soc/bcm/Kconfig
-+++ b/sound/soc/bcm/Kconfig
-@@ -92,3 +92,11 @@ config SND_AUDIOINJECTOR_PI_SOUNDCARD
- select SND_SOC_WM8731
- help
- Say Y or M if you want to add support for audioinjector.net Pi Hat
-+
-+config SND_DIGIDAC1_SOUNDCARD
-+ tristate "Support for Red Rocks Audio DigiDAC1"
-+ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
-+ select SND_SOC_WM8804
-+ select SND_SOC_WM8741
-+ help
-+ Say Y or M if you want to add support for Red Rocks Audio DigiDAC1 board.
---- a/sound/soc/bcm/Makefile
-+++ b/sound/soc/bcm/Makefile
-@@ -16,6 +16,7 @@ snd-soc-rpi-proto-objs := rpi-proto.o
- snd-soc-iqaudio-dac-objs := iqaudio-dac.o
- snd-soc-raspidac3-objs := raspidac3.o
- snd-soc-audioinjector-pi-soundcard-objs := audioinjector-pi-soundcard.o
-+snd-soc-digidac1-soundcard-objs := digidac1-soundcard.o
-
- obj-$(CONFIG_SND_BCM2708_SOC_ADAU1977_ADC) += snd-soc-adau1977-adc.o
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DAC) += snd-soc-hifiberry-dac.o
-@@ -29,4 +30,5 @@ obj-$(CONFIG_SND_BCM2708_SOC_RPI_PROTO)
- obj-$(CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC) += snd-soc-iqaudio-dac.o
- obj-$(CONFIG_SND_BCM2708_SOC_RASPIDAC3) += snd-soc-raspidac3.o
- obj-$(CONFIG_SND_AUDIOINJECTOR_PI_SOUNDCARD) += snd-soc-audioinjector-pi-soundcard.o
-+obj-$(CONFIG_SND_DIGIDAC1_SOUNDCARD) += snd-soc-digidac1-soundcard.o
-
---- /dev/null
-+++ b/sound/soc/bcm/digidac1-soundcard.c
-@@ -0,0 +1,422 @@
-+/*
-+ * ASoC Driver for RRA DigiDAC1
-+ * Copyright 2016
-+ * Author: José M. Tasende <vintage at redrocksaudio.es>
-+ * based on the HifiBerry DAC driver by Florian Meier <florian.meier at koalo.de>
-+ * and the Wolfson card driver by Nikesh Oswal, <Nikesh.Oswal at wolfsonmicro.com>
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * version 2 as published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful, but
-+ * WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
-+ * General Public License for more details.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+#include <linux/i2c.h>
-+#include <sound/core.h>
-+#include <sound/pcm.h>
-+#include <sound/pcm_params.h>
-+#include <sound/soc.h>
-+#include <sound/jack.h>
-+#include <sound/soc-dapm.h>
-+#include <sound/tlv.h>
-+#include <linux/regulator/consumer.h>
-+
-+#include "../codecs/wm8804.h"
-+#include "../codecs/wm8741.h"
-+
-+#define WM8741_NUM_SUPPLIES 2
-+
-+/* codec private data */
-+struct wm8741_priv {
-+ struct wm8741_platform_data pdata;
-+ struct regmap *regmap;
-+ struct regulator_bulk_data supplies[WM8741_NUM_SUPPLIES];
-+ unsigned int sysclk;
-+ const struct snd_pcm_hw_constraint_list *sysclk_constraints;
-+};
-+
-+static int samplerate = 44100;
-+
-+/* New Alsa Controls not exposed by original wm8741 codec driver */
-+/* in actual driver the att. adjustment is wrong because */
-+/* this DAC has a coarse attenuation register with 4dB steps */
-+/* and a fine level register with 0.125dB steps */
-+/* each register has 32 steps so combining both we have 1024 steps */
-+/* of 0.125 dB. */
-+/* The original level controls from driver are removed at startup */
-+/* and replaced by the corrected ones. */
-+/* The same wm8741 driver can be used for wm8741 and wm8742 devices */
-+
-+static const DECLARE_TLV_DB_SCALE(dac_tlv_fine, 0, 13, 0);
-+static const DECLARE_TLV_DB_SCALE(dac_tlv_coarse, -12700, 400, 1);
-+static const char *w8741_dither[4] = {"Off", "RPDF", "TPDF", "HPDF"};
-+static const char *w8741_filter[5] = {
-+ "Type 1", "Type 2", "Type 3", "Type 4", "Type 5"};
-+static const char *w8741_switch[2] = {"Off", "On"};
-+static const struct soc_enum w8741_enum[] = {
-+SOC_ENUM_SINGLE(WM8741_MODE_CONTROL_2, 0, 4, w8741_dither),/* dithering type */
-+SOC_ENUM_SINGLE(WM8741_FILTER_CONTROL, 0, 5, w8741_filter),/* filter type */
-+SOC_ENUM_SINGLE(WM8741_FORMAT_CONTROL, 6, 2, w8741_switch),/* phase invert */
-+SOC_ENUM_SINGLE(WM8741_VOLUME_CONTROL, 0, 2, w8741_switch),/* volume ramp */
-+SOC_ENUM_SINGLE(WM8741_VOLUME_CONTROL, 3, 2, w8741_switch),/* soft mute */
-+};
-+
-+static const struct snd_kcontrol_new w8741_snd_controls_stereo[] = {
-+SOC_DOUBLE_R_TLV("DAC Fine Playback Volume", WM8741_DACLLSB_ATTENUATION,
-+ WM8741_DACRLSB_ATTENUATION, 0, 31, 1, dac_tlv_fine),
-+SOC_DOUBLE_R_TLV("Digital Playback Volume", WM8741_DACLMSB_ATTENUATION,
-+ WM8741_DACRMSB_ATTENUATION, 0, 31, 1, dac_tlv_coarse),
-+SOC_ENUM("DAC Dither", w8741_enum[0]),
-+SOC_ENUM("DAC Digital Filter", w8741_enum[1]),
-+SOC_ENUM("DAC Phase Invert", w8741_enum[2]),
-+SOC_ENUM("DAC Volume Ramp", w8741_enum[3]),
-+SOC_ENUM("DAC Soft Mute", w8741_enum[4]),
-+};
-+
-+static const struct snd_kcontrol_new w8741_snd_controls_mono_left[] = {
-+SOC_SINGLE_TLV("DAC Fine Playback Volume", WM8741_DACLLSB_ATTENUATION,
-+ 0, 31, 0, dac_tlv_fine),
-+SOC_SINGLE_TLV("Digital Playback Volume", WM8741_DACLMSB_ATTENUATION,
-+ 0, 31, 1, dac_tlv_coarse),
-+SOC_ENUM("DAC Dither", w8741_enum[0]),
-+SOC_ENUM("DAC Digital Filter", w8741_enum[1]),
-+SOC_ENUM("DAC Phase Invert", w8741_enum[2]),
-+SOC_ENUM("DAC Volume Ramp", w8741_enum[3]),
-+SOC_ENUM("DAC Soft Mute", w8741_enum[4]),
-+};
-+
-+static const struct snd_kcontrol_new w8741_snd_controls_mono_right[] = {
-+SOC_SINGLE_TLV("DAC Fine Playback Volume", WM8741_DACRLSB_ATTENUATION,
-+ 0, 31, 0, dac_tlv_fine),
-+SOC_SINGLE_TLV("Digital Playback Volume", WM8741_DACRMSB_ATTENUATION,
-+ 0, 31, 1, dac_tlv_coarse),
-+SOC_ENUM("DAC Dither", w8741_enum[0]),
-+SOC_ENUM("DAC Digital Filter", w8741_enum[1]),
-+SOC_ENUM("DAC Phase Invert", w8741_enum[2]),
-+SOC_ENUM("DAC Volume Ramp", w8741_enum[3]),
-+SOC_ENUM("DAC Soft Mute", w8741_enum[4]),
-+};
-+
-+static int w8741_add_controls(struct snd_soc_codec *codec)
-+{
-+ struct wm8741_priv *wm8741 = snd_soc_codec_get_drvdata(codec);
-+
-+ switch (wm8741->pdata.diff_mode) {
-+ case WM8741_DIFF_MODE_STEREO:
-+ case WM8741_DIFF_MODE_STEREO_REVERSED:
-+ snd_soc_add_codec_controls(codec,
-+ w8741_snd_controls_stereo,
-+ ARRAY_SIZE(w8741_snd_controls_stereo));
-+ break;
-+ case WM8741_DIFF_MODE_MONO_LEFT:
-+ snd_soc_add_codec_controls(codec,
-+ w8741_snd_controls_mono_left,
-+ ARRAY_SIZE(w8741_snd_controls_mono_left));
-+ break;
-+ case WM8741_DIFF_MODE_MONO_RIGHT:
-+ snd_soc_add_codec_controls(codec,
-+ w8741_snd_controls_mono_right,
-+ ARRAY_SIZE(w8741_snd_controls_mono_right));
-+ break;
-+ default:
-+ return -EINVAL;
-+ }
-+
-+ return 0;
-+}
-+
-+static int digidac1_soundcard_init(struct snd_soc_pcm_runtime *rtd)
-+{
-+ struct snd_soc_codec *codec = rtd->codec;
-+ struct snd_soc_card *card = rtd->card;
-+ struct snd_soc_pcm_runtime *wm8741_rtd;
-+ struct snd_soc_codec *wm8741_codec;
-+ struct snd_card *sound_card = card->snd_card;
-+ struct snd_kcontrol *kctl;
-+ int ret;
-+
-+ wm8741_rtd = snd_soc_get_pcm_runtime(card, card->dai_link[1].name);
-+ if (!wm8741_rtd) {
-+ dev_warn(card->dev, "digidac1_soundcard_init: couldn't get wm8741 rtd\n");
-+ return -EFAULT;
-+ }
-+ wm8741_codec = wm8741_rtd->codec;
-+ ret = w8741_add_controls(wm8741_codec);
-+ if (ret < 0)
-+ dev_warn(card->dev, "Failed to add new wm8741 controls: %d\n",
-+ ret);
-+
-+ /* enable TX output */
-+ snd_soc_update_bits(codec, WM8804_PWRDN, 0x4, 0x0);
-+
-+ kctl = snd_soc_card_get_kcontrol(card,
-+ "Playback Volume");
-+ if (kctl) {
-+ kctl->vd[0].access = SNDRV_CTL_ELEM_ACCESS_READWRITE;
-+ snd_ctl_remove(sound_card, kctl);
-+ }
-+ kctl = snd_soc_card_get_kcontrol(card,
-+ "Fine Playback Volume");
-+ if (kctl) {
-+ kctl->vd[0].access = SNDRV_CTL_ELEM_ACCESS_READWRITE;
-+ snd_ctl_remove(sound_card, kctl);
-+ }
-+ return 0;
-+}
-+
-+static int digidac1_soundcard_startup(struct snd_pcm_substream *substream)
-+{
-+ /* turn on wm8804 digital output */
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_codec *codec = rtd->codec;
-+ struct snd_soc_card *card = rtd->card;
-+ struct snd_soc_pcm_runtime *wm8741_rtd;
-+ struct snd_soc_codec *wm8741_codec;
-+
-+ snd_soc_update_bits(codec, WM8804_PWRDN, 0x3c, 0x00);
-+ wm8741_rtd = snd_soc_get_pcm_runtime(card, card->dai_link[1].name);
-+ if (!wm8741_rtd) {
-+ dev_warn(card->dev, "digidac1_soundcard_startup: couldn't get WM8741 rtd\n");
-+ return -EFAULT;
-+ }
-+ wm8741_codec = wm8741_rtd->codec;
-+
-+ /* latch wm8741 level */
-+ snd_soc_update_bits(wm8741_codec, WM8741_DACLLSB_ATTENUATION,
-+ WM8741_UPDATELL, WM8741_UPDATELL);
-+ snd_soc_update_bits(wm8741_codec, WM8741_DACLMSB_ATTENUATION,
-+ WM8741_UPDATELM, WM8741_UPDATELM);
-+ snd_soc_update_bits(wm8741_codec, WM8741_DACRLSB_ATTENUATION,
-+ WM8741_UPDATERL, WM8741_UPDATERL);
-+ snd_soc_update_bits(wm8741_codec, WM8741_DACRMSB_ATTENUATION,
-+ WM8741_UPDATERM, WM8741_UPDATERM);
-+
-+ return 0;
-+}
-+
-+static void digidac1_soundcard_shutdown(struct snd_pcm_substream *substream)
-+{
-+ /* turn off wm8804 digital output */
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_codec *codec = rtd->codec;
-+
-+ snd_soc_update_bits(codec, WM8804_PWRDN, 0x3c, 0x3c);
-+}
-+
-+static int digidac1_soundcard_hw_params(struct snd_pcm_substream *substream,
-+ struct snd_pcm_hw_params *params)
-+{
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_dai *codec_dai = rtd->codec_dai;
-+ struct snd_soc_codec *codec = rtd->codec;
-+ struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
-+ struct snd_soc_card *card = rtd->card;
-+ struct snd_soc_pcm_runtime *wm8741_rtd;
-+ struct snd_soc_codec *wm8741_codec;
-+
-+ int sysclk = 27000000;
-+ long mclk_freq = 0;
-+ int mclk_div = 1;
-+ int sampling_freq = 1;
-+ int ret;
-+
-+ wm8741_rtd = snd_soc_get_pcm_runtime(card, card->dai_link[1].name);
-+ if (!wm8741_rtd) {
-+ dev_warn(card->dev, "digidac1_soundcard_hw_params: couldn't get WM8741 rtd\n");
-+ return -EFAULT;
-+ }
-+ wm8741_codec = wm8741_rtd->codec;
-+ samplerate = params_rate(params);
-+
-+ if (samplerate <= 96000) {
-+ mclk_freq = samplerate*256;
-+ mclk_div = WM8804_MCLKDIV_256FS;
-+ } else {
-+ mclk_freq = samplerate*128;
-+ mclk_div = WM8804_MCLKDIV_128FS;
-+ }
-+
-+ switch (samplerate) {
-+ case 32000:
-+ sampling_freq = 0x03;
-+ break;
-+ case 44100:
-+ sampling_freq = 0x00;
-+ break;
-+ case 48000:
-+ sampling_freq = 0x02;
-+ break;
-+ case 88200:
-+ sampling_freq = 0x08;
-+ break;
-+ case 96000:
-+ sampling_freq = 0x0a;
-+ break;
-+ case 176400:
-+ sampling_freq = 0x0c;
-+ break;
-+ case 192000:
-+ sampling_freq = 0x0e;
-+ break;
-+ default:
-+ dev_err(codec->dev,
-+ "Failed to set WM8804 SYSCLK, unsupported samplerate %d\n",
-+ samplerate);
-+ }
-+
-+ snd_soc_dai_set_clkdiv(codec_dai, WM8804_MCLK_DIV, mclk_div);
-+ snd_soc_dai_set_pll(codec_dai, 0, 0, sysclk, mclk_freq);
-+
-+ ret = snd_soc_dai_set_sysclk(codec_dai, WM8804_TX_CLKSRC_PLL,
-+ sysclk, SND_SOC_CLOCK_OUT);
-+ if (ret < 0) {
-+ dev_err(codec->dev,
-+ "Failed to set WM8804 SYSCLK: %d\n", ret);
-+ return ret;
-+ }
-+ /* Enable wm8804 TX output */
-+ snd_soc_update_bits(codec, WM8804_PWRDN, 0x4, 0x0);
-+
-+ /* wm8804 Power on */
-+ snd_soc_update_bits(codec, WM8804_PWRDN, 0x9, 0);
-+
-+ /* wm8804 set sampling frequency status bits */
-+ snd_soc_update_bits(codec, WM8804_SPDTX4, 0x0f, sampling_freq);
-+
-+ /* Now update wm8741 registers for the correct oversampling */
-+ if (samplerate <= 48000)
-+ snd_soc_update_bits(wm8741_codec, WM8741_MODE_CONTROL_1,
-+ WM8741_OSR_MASK, 0x00);
-+ else if (samplerate <= 96000)
-+ snd_soc_update_bits(wm8741_codec, WM8741_MODE_CONTROL_1,
-+ WM8741_OSR_MASK, 0x20);
-+ else
-+ snd_soc_update_bits(wm8741_codec, WM8741_MODE_CONTROL_1,
-+ WM8741_OSR_MASK, 0x40);
-+
-+ /* wm8741 bit size */
-+ switch (params_width(params)) {
-+ case 16:
-+ snd_soc_update_bits(wm8741_codec, WM8741_FORMAT_CONTROL,
-+ WM8741_IWL_MASK, 0x00);
-+ break;
-+ case 20:
-+ snd_soc_update_bits(wm8741_codec, WM8741_FORMAT_CONTROL,
-+ WM8741_IWL_MASK, 0x01);
-+ break;
-+ case 24:
-+ snd_soc_update_bits(wm8741_codec, WM8741_FORMAT_CONTROL,
-+ WM8741_IWL_MASK, 0x02);
-+ break;
-+ case 32:
-+ snd_soc_update_bits(wm8741_codec, WM8741_FORMAT_CONTROL,
-+ WM8741_IWL_MASK, 0x03);
-+ break;
-+ default:
-+ dev_dbg(codec->dev, "wm8741_hw_params: Unsupported bit size param = %d",
-+ params_width(params));
-+ return -EINVAL;
-+ }
-+
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, 64);
-+}
-+/* machine stream operations */
-+static struct snd_soc_ops digidac1_soundcard_ops = {
-+ .hw_params = digidac1_soundcard_hw_params,
-+ .startup = digidac1_soundcard_startup,
-+ .shutdown = digidac1_soundcard_shutdown,
-+};
-+
-+static struct snd_soc_dai_link digidac1_soundcard_dai[] = {
-+ {
-+ .name = "RRA DigiDAC1",
-+ .stream_name = "RRA DigiDAC1 HiFi",
-+ .cpu_dai_name = "bcm2708-i2s.0",
-+ .codec_dai_name = "wm8804-spdif",
-+ .platform_name = "bcm2708-i2s.0",
-+ .codec_name = "wm8804.1-003b",
-+ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF |
-+ SND_SOC_DAIFMT_CBM_CFM,
-+ .ops = &digidac1_soundcard_ops,
-+ .init = digidac1_soundcard_init,
-+ },
-+ {
-+ .name = "RRA DigiDAC11",
-+ .stream_name = "RRA DigiDAC11 HiFi",
-+ .cpu_dai_name = "wm8804-spdif",
-+ .codec_dai_name = "wm8741",
-+ .codec_name = "wm8741.1-001a",
-+ .dai_fmt = SND_SOC_DAIFMT_I2S
-+ | SND_SOC_DAIFMT_NB_NF
-+ | SND_SOC_DAIFMT_CBS_CFS,
-+ },
-+};
-+
-+/* audio machine driver */
-+static struct snd_soc_card digidac1_soundcard = {
-+ .name = "digidac1-soundcard",
-+ .owner = THIS_MODULE,
-+ .dai_link = digidac1_soundcard_dai,
-+ .num_links = ARRAY_SIZE(digidac1_soundcard_dai),
-+};
-+
-+static int digidac1_soundcard_probe(struct platform_device *pdev)
-+{
-+ int ret = 0;
-+
-+ digidac1_soundcard.dev = &pdev->dev;
-+
-+ if (pdev->dev.of_node) {
-+ struct device_node *i2s_node;
-+ struct snd_soc_dai_link *dai = &digidac1_soundcard_dai[0];
-+
-+ i2s_node = of_parse_phandle(pdev->dev.of_node,
-+ "i2s-controller", 0);
-+
-+ if (i2s_node) {
-+ dai->cpu_dai_name = NULL;
-+ dai->cpu_of_node = i2s_node;
-+ dai->platform_name = NULL;
-+ dai->platform_of_node = i2s_node;
-+ }
-+ }
-+
-+ ret = snd_soc_register_card(&digidac1_soundcard);
-+ if (ret)
-+ dev_err(&pdev->dev, "snd_soc_register_card() failed: %d\n",
-+ ret);
-+
-+ return ret;
-+}
-+
-+static int digidac1_soundcard_remove(struct platform_device *pdev)
-+{
-+ return snd_soc_unregister_card(&digidac1_soundcard);
-+}
-+
-+static const struct of_device_id digidac1_soundcard_of_match[] = {
-+ { .compatible = "rra,digidac1-soundcard", },
-+ {},
-+};
-+MODULE_DEVICE_TABLE(of, digidac1_soundcard_of_match);
-+
-+static struct platform_driver digidac1_soundcard_driver = {
-+ .driver = {
-+ .name = "digidac1-audio",
-+ .owner = THIS_MODULE,
-+ .of_match_table = digidac1_soundcard_of_match,
-+ },
-+ .probe = digidac1_soundcard_probe,
-+ .remove = digidac1_soundcard_remove,
-+};
-+
-+module_platform_driver(digidac1_soundcard_driver);
-+
-+MODULE_AUTHOR("José M. Tasende <vintage at redrocksaudio.es>");
-+MODULE_DESCRIPTION("ASoC Driver for RRA DigiDAC1");
-+MODULE_LICENSE("GPL v2");
diff --git a/target/linux/brcm2708/patches-4.4/0373-BCM2835-V4L2-Correct-handling-for-BGR24-vs-RGB24.patch b/target/linux/brcm2708/patches-4.4/0373-BCM2835-V4L2-Correct-handling-for-BGR24-vs-RGB24.patch
deleted file mode 100644
index e48a0d3..0000000
--- a/target/linux/brcm2708/patches-4.4/0373-BCM2835-V4L2-Correct-handling-for-BGR24-vs-RGB24.patch
+++ /dev/null
@@ -1,170 +0,0 @@
-From 94e0b7315a48c6080240ea5bc8b43a17b7cb48b3 Mon Sep 17 00:00:00 2001
-From: Dave Stevenson <6by9 at users.noreply.github.com>
-Date: Wed, 25 May 2016 23:25:36 +0100
-Subject: [PATCH] BCM2835-V4L2: Correct handling for BGR24 vs RGB24.
-
-There was a bug in the GPU firmware that had reversed these
-two formats.
-Detect the old firmware, and reverse the formats if necessary.
-
-Signed-off-by: Dave Stevenson <6by9 at users.noreply.github.com>
----
- drivers/media/platform/bcm2835/bcm2835-camera.c | 69 ++++++++++++++++++-------
- drivers/media/platform/bcm2835/bcm2835-camera.h | 1 +
- 2 files changed, 52 insertions(+), 18 deletions(-)
-
---- a/drivers/media/platform/bcm2835/bcm2835-camera.c
-+++ b/drivers/media/platform/bcm2835/bcm2835-camera.c
-@@ -115,7 +115,7 @@ static struct mmal_fmt formats[] = {
- .name = "RGB24 (LE)",
- .fourcc = V4L2_PIX_FMT_RGB24,
- .flags = 0,
-- .mmal = MMAL_ENCODING_BGR24,
-+ .mmal = MMAL_ENCODING_RGB24,
- .depth = 24,
- .mmal_component = MMAL_COMPONENT_CAMERA,
- .ybbp = 3,
-@@ -187,7 +187,7 @@ static struct mmal_fmt formats[] = {
- .name = "RGB24 (BE)",
- .fourcc = V4L2_PIX_FMT_BGR24,
- .flags = 0,
-- .mmal = MMAL_ENCODING_RGB24,
-+ .mmal = MMAL_ENCODING_BGR24,
- .depth = 24,
- .mmal_component = MMAL_COMPONENT_CAMERA,
- .ybbp = 3,
-@@ -1059,6 +1059,13 @@ static int mmal_setup_components(struct
- else
- camera_port->format.encoding = mfmt->mmal;
-
-+ if (dev->rgb_bgr_swapped) {
-+ if (camera_port->format.encoding == MMAL_ENCODING_RGB24)
-+ camera_port->format.encoding = MMAL_ENCODING_BGR24;
-+ else if (camera_port->format.encoding == MMAL_ENCODING_BGR24)
-+ camera_port->format.encoding = MMAL_ENCODING_RGB24;
-+ }
-+
- camera_port->format.encoding_variant = 0;
- camera_port->es.video.width = f->fmt.pix.width;
- camera_port->es.video.height = f->fmt.pix.height;
-@@ -1569,12 +1576,17 @@ static int set_camera_parameters(struct
- return ret;
- }
-
-+#define MAX_SUPPORTED_ENCODINGS 20
-+
- /* MMAL instance and component init */
- static int __init mmal_init(struct bm2835_mmal_dev *dev)
- {
- int ret;
- struct mmal_es_format *format;
- u32 bool_true = 1;
-+ u32 supported_encodings[MAX_SUPPORTED_ENCODINGS];
-+ int param_size;
-+ struct vchiq_mmal_component *camera;
-
- ret = vchiq_mmal_init(&dev->instance);
- if (ret < 0)
-@@ -1586,21 +1598,48 @@ static int __init mmal_init(struct bm283
- if (ret < 0)
- goto unreg_mmal;
-
-- if (dev->component[MMAL_COMPONENT_CAMERA]->outputs <
-- MMAL_CAMERA_PORT_COUNT) {
-+ camera = dev->component[MMAL_COMPONENT_CAMERA];
-+ if (camera->outputs < MMAL_CAMERA_PORT_COUNT) {
- ret = -EINVAL;
- goto unreg_camera;
- }
-
- ret = set_camera_parameters(dev->instance,
-- dev->component[MMAL_COMPONENT_CAMERA],
-+ camera,
- dev);
- if (ret < 0)
- goto unreg_camera;
-
-- format =
-- &dev->component[MMAL_COMPONENT_CAMERA]->
-- output[MMAL_CAMERA_PORT_PREVIEW].format;
-+ /* There was an error in the firmware that meant the camera component
-+ * produced BGR instead of RGB.
-+ * This is now fixed, but in order to support the old firmwares, we
-+ * have to check.
-+ */
-+ dev->rgb_bgr_swapped = true;
-+ param_size = sizeof(supported_encodings);
-+ ret = vchiq_mmal_port_parameter_get(dev->instance,
-+ &camera->output[MMAL_CAMERA_PORT_CAPTURE],
-+ MMAL_PARAMETER_SUPPORTED_ENCODINGS,
-+ &supported_encodings,
-+ ¶m_size);
-+ if (ret == 0) {
-+ int i;
-+
-+ for (i = 0; i < param_size/sizeof(u32); i++) {
-+ if (supported_encodings[i] == MMAL_ENCODING_BGR24) {
-+ /* Found BGR24 first - old firmware. */
-+ break;
-+ }
-+ if (supported_encodings[i] == MMAL_ENCODING_RGB24) {
-+ /* Found RGB24 first
-+ * new firmware, so use RGB24.
-+ */
-+ dev->rgb_bgr_swapped = false;
-+ break;
-+ }
-+ }
-+ }
-+ format = &camera->output[MMAL_CAMERA_PORT_PREVIEW].format;
-
- format->encoding = MMAL_ENCODING_OPAQUE;
- format->encoding_variant = MMAL_ENCODING_I420;
-@@ -1614,9 +1653,7 @@ static int __init mmal_init(struct bm283
- format->es->video.frame_rate.num = 0; /* Rely on fps_range */
- format->es->video.frame_rate.den = 1;
-
-- format =
-- &dev->component[MMAL_COMPONENT_CAMERA]->
-- output[MMAL_CAMERA_PORT_VIDEO].format;
-+ format = &camera->output[MMAL_CAMERA_PORT_VIDEO].format;
-
- format->encoding = MMAL_ENCODING_OPAQUE;
- format->encoding_variant = MMAL_ENCODING_I420;
-@@ -1631,14 +1668,11 @@ static int __init mmal_init(struct bm283
- format->es->video.frame_rate.den = 1;
-
- vchiq_mmal_port_parameter_set(dev->instance,
-- &dev->component[MMAL_COMPONENT_CAMERA]->
-- output[MMAL_CAMERA_PORT_VIDEO],
-+ &camera->output[MMAL_CAMERA_PORT_VIDEO],
- MMAL_PARAMETER_NO_IMAGE_PADDING,
- &bool_true, sizeof(bool_true));
-
-- format =
-- &dev->component[MMAL_COMPONENT_CAMERA]->
-- output[MMAL_CAMERA_PORT_CAPTURE].format;
-+ format = &camera->output[MMAL_CAMERA_PORT_CAPTURE].format;
-
- format->encoding = MMAL_ENCODING_OPAQUE;
-
-@@ -1660,8 +1694,7 @@ static int __init mmal_init(struct bm283
- dev->capture.enc_level = V4L2_MPEG_VIDEO_H264_LEVEL_4_0;
-
- vchiq_mmal_port_parameter_set(dev->instance,
-- &dev->component[MMAL_COMPONENT_CAMERA]->
-- output[MMAL_CAMERA_PORT_CAPTURE],
-+ &camera->output[MMAL_CAMERA_PORT_CAPTURE],
- MMAL_PARAMETER_NO_IMAGE_PADDING,
- &bool_true, sizeof(bool_true));
-
---- a/drivers/media/platform/bcm2835/bcm2835-camera.h
-+++ b/drivers/media/platform/bcm2835/bcm2835-camera.h
-@@ -109,6 +109,7 @@ struct bm2835_mmal_dev {
- unsigned int camera_num;
- unsigned int max_width;
- unsigned int max_height;
-+ unsigned int rgb_bgr_swapped;
- };
-
- int bm2835_mmal_init_controls(
diff --git a/target/linux/brcm2708/patches-4.4/0374-BCM270X_DT-Add-mcp23017-to-the-overlay-Makefile.patch b/target/linux/brcm2708/patches-4.4/0374-BCM270X_DT-Add-mcp23017-to-the-overlay-Makefile.patch
deleted file mode 100644
index a15e885..0000000
--- a/target/linux/brcm2708/patches-4.4/0374-BCM270X_DT-Add-mcp23017-to-the-overlay-Makefile.patch
+++ /dev/null
@@ -1,20 +0,0 @@
-From 87115acb06c36e0e3519ce6af3f0b2506cb22a42 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 3 Jun 2016 22:21:47 +0100
-Subject: [PATCH] BCM270X_DT: Add mcp23017 to the overlay Makefile
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- 1 file changed, 1 insertion(+)
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -44,6 +44,7 @@ dtbo-$(RPI_DT_OVERLAYS) += iqaudio-dacpl
- dtbo-$(RPI_DT_OVERLAYS) += justboom-dac.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += justboom-digi.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += lirc-rpi.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += mcp23017.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += mcp2515-can0.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += mcp2515-can1.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += mmc.dtbo
diff --git a/target/linux/brcm2708/patches-4.4/0375-BCM270X_DT-Sort-entries-to-placate-check-script.patch b/target/linux/brcm2708/patches-4.4/0375-BCM270X_DT-Sort-entries-to-placate-check-script.patch
deleted file mode 100644
index 1869f1d..0000000
--- a/target/linux/brcm2708/patches-4.4/0375-BCM270X_DT-Sort-entries-to-placate-check-script.patch
+++ /dev/null
@@ -1,56 +0,0 @@
-From 1adea82b353d310284c6510627bb6acc4f43cbf3 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 3 Jun 2016 23:01:01 +0100
-Subject: [PATCH] BCM270X_DT: Sort entries to placate check script
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/overlays/Makefile | 10 +++++-----
- 1 file changed, 5 insertions(+), 5 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -18,10 +18,10 @@ dtbo-$(RPI_DT_OVERLAYS) += akkordion-iqd
- dtbo-$(RPI_DT_OVERLAYS) += at86rf233.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += audioinjector-wm8731-audio.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += bmp085_i2c-sensor.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += dht11.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += dpi24.dtbo
--dtbo-$(RPI_DT_OVERLAYS) += dwc2.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += dwc-otg.dtbo
--dtbo-$(RPI_DT_OVERLAYS) += dht11.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += dwc2.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += enc28j60.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += gpio-ir.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += gpio-poweroff.dtbo
-@@ -31,10 +31,10 @@ dtbo-$(RPI_DT_OVERLAYS) += hifiberry-dac
- dtbo-$(RPI_DT_OVERLAYS) += hifiberry-digi.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += hy28a.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += hy28b.dtbo
--dtbo-$(RPI_DT_OVERLAYS) += i2c-rtc.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c-gpio.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c-mux.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c-pwm-pca9685a.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += i2c-rtc.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c0-bcm2708.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c1-bcm2708.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2s-gpio28-31.dtbo
-@@ -73,16 +73,16 @@ dtbo-$(RPI_DT_OVERLAYS) += sdhost.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += sdio.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += sdio-1bit.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += sdtweak.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += smi.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += smi-dev.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += smi-nand.dtbo
--dtbo-$(RPI_DT_OVERLAYS) += smi.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += spi-gpio35-39.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += spi1-1cs.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += spi1-2cs.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += spi1-3cs.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += spi2-1cs.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += spi2-2cs.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += spi2-3cs.dtbo
--dtbo-$(RPI_DT_OVERLAYS) += spi-gpio35-39.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += tinylcd35.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += uart1.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += vc4-kms-v3d.dtbo
diff --git a/target/linux/brcm2708/patches-4.4/0376-gpio-ir-overlay-gpio_pin-shouldn-t-change-pull-setti.patch b/target/linux/brcm2708/patches-4.4/0376-gpio-ir-overlay-gpio_pin-shouldn-t-change-pull-setti.patch
deleted file mode 100644
index 632a0fd..0000000
--- a/target/linux/brcm2708/patches-4.4/0376-gpio-ir-overlay-gpio_pin-shouldn-t-change-pull-setti.patch
+++ /dev/null
@@ -1,22 +0,0 @@
-From 2d6a2582cc4995a962a58a4468705c347c11473e Mon Sep 17 00:00:00 2001
-From: Matthias Reichl <hias at horus.com>
-Date: Sat, 4 Jun 2016 11:30:48 +0200
-Subject: [PATCH] gpio-ir overlay: gpio_pin shouldn't change pull setting
-
-Signed-off-by: Matthias Reichl <hias at horus.com>
----
- arch/arm/boot/dts/overlays/gpio-ir-overlay.dts | 3 +--
- 1 file changed, 1 insertion(+), 2 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/gpio-ir-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/gpio-ir-overlay.dts
-@@ -36,8 +36,7 @@
- __overrides__ {
- // parameters
- gpio_pin = <&gpio_ir>,"gpios:4",
-- <&gpio_ir_pins>,"brcm,pins:0",
-- <&gpio_ir_pins>,"brcm,pull:0"; // pin number
-+ <&gpio_ir_pins>,"brcm,pins:0"; // pin number
- gpio_pull = <&gpio_ir_pins>,"brcm,pull:0"; // pull-up/down state
-
- rc-map-name = <&gpio_ir>,"linux,rc-map-name"; // default rc map
diff --git a/target/linux/brcm2708/patches-4.4/0377-media-rc-core-define-a-default-timeout-for-drivers.patch b/target/linux/brcm2708/patches-4.4/0377-media-rc-core-define-a-default-timeout-for-drivers.patch
deleted file mode 100644
index 92dc90e..0000000
--- a/target/linux/brcm2708/patches-4.4/0377-media-rc-core-define-a-default-timeout-for-drivers.patch
+++ /dev/null
@@ -1,25 +0,0 @@
-From d71470889e080d423eb94be1717a5f4e96add3cd Mon Sep 17 00:00:00 2001
-From: Eric Nelson <eric at nelint.com>
-Date: Sat, 3 Oct 2015 08:18:50 -0700
-Subject: [PATCH] [media] rc-core: define a default timeout for drivers
-
-A default timeout value of 125 ms should work for all decoders.
-
-Declare a constant to help standardize its' use.
-
-Signed-off-by: Eric Nelson <eric at nelint.com>
-Signed-off-by: Mauro Carvalho Chehab <mchehab at osg.samsung.com>
----
- include/media/rc-core.h | 1 +
- 1 file changed, 1 insertion(+)
-
---- a/include/media/rc-core.h
-+++ b/include/media/rc-core.h
-@@ -239,6 +239,7 @@ static inline void init_ir_raw_event(str
- memset(ev, 0, sizeof(*ev));
- }
-
-+#define IR_DEFAULT_TIMEOUT MS_TO_NS(125)
- #define IR_MAX_DURATION 500000000 /* 500 ms */
- #define US_TO_NS(usec) ((usec) * 1000)
- #define MS_TO_US(msec) ((msec) * 1000)
diff --git a/target/linux/brcm2708/patches-4.4/0378-media-rc-gpio-ir-recv-add-timeout-on-idle.patch b/target/linux/brcm2708/patches-4.4/0378-media-rc-gpio-ir-recv-add-timeout-on-idle.patch
deleted file mode 100644
index a745cea..0000000
--- a/target/linux/brcm2708/patches-4.4/0378-media-rc-gpio-ir-recv-add-timeout-on-idle.patch
+++ /dev/null
@@ -1,91 +0,0 @@
-From 1f899a2d03b1751ef5adc4c5c0706c83dfcf7256 Mon Sep 17 00:00:00 2001
-From: Eric Nelson <eric at nelint.com>
-Date: Wed, 23 Sep 2015 11:07:08 -0300
-Subject: [PATCH] [media] rc: gpio-ir-recv: add timeout on idle
-
-Many decoders require a trailing space (period without IR illumination)
-to be delivered before completing a decode.
-
-Since the gpio-ir-recv driver only delivers events on gpio transitions,
-a single IR symbol (caused by a quick touch on an IR remote) will not
-be properly decoded without the use of a timer to flush the tail end
-state of the IR receiver.
-
-This patch initializes and uses a timer and the timeout field of rcdev
-to complete the stream and allow decode.
-
-The timeout can be overridden through the use of the LIRC_SET_REC_TIMEOUT
-ioctl.
-
-Signed-off-by: Eric Nelson <eric at nelint.com>
-Acked-by: Sean Young <sean at mess.org>
-Signed-off-by: Mauro Carvalho Chehab <mchehab at osg.samsung.com>
----
- drivers/media/rc/gpio-ir-recv.c | 22 ++++++++++++++++++++++
- 1 file changed, 22 insertions(+)
-
---- a/drivers/media/rc/gpio-ir-recv.c
-+++ b/drivers/media/rc/gpio-ir-recv.c
-@@ -30,6 +30,7 @@ struct gpio_rc_dev {
- struct rc_dev *rcdev;
- int gpio_nr;
- bool active_low;
-+ struct timer_list flush_timer;
- };
-
- #ifdef CONFIG_OF
-@@ -93,12 +94,26 @@ static irqreturn_t gpio_ir_recv_irq(int
- if (rc < 0)
- goto err_get_value;
-
-+ mod_timer(&gpio_dev->flush_timer,
-+ jiffies + nsecs_to_jiffies(gpio_dev->rcdev->timeout));
-+
- ir_raw_event_handle(gpio_dev->rcdev);
-
- err_get_value:
- return IRQ_HANDLED;
- }
-
-+static void flush_timer(unsigned long arg)
-+{
-+ struct gpio_rc_dev *gpio_dev = (struct gpio_rc_dev *)arg;
-+ DEFINE_IR_RAW_EVENT(ev);
-+
-+ ev.timeout = true;
-+ ev.duration = gpio_dev->rcdev->timeout;
-+ ir_raw_event_store(gpio_dev->rcdev, &ev);
-+ ir_raw_event_handle(gpio_dev->rcdev);
-+}
-+
- static int gpio_ir_recv_probe(struct platform_device *pdev)
- {
- struct gpio_rc_dev *gpio_dev;
-@@ -144,6 +159,9 @@ static int gpio_ir_recv_probe(struct pla
- rcdev->input_id.version = 0x0100;
- rcdev->dev.parent = &pdev->dev;
- rcdev->driver_name = GPIO_IR_DRIVER_NAME;
-+ rcdev->min_timeout = 0;
-+ rcdev->timeout = IR_DEFAULT_TIMEOUT;
-+ rcdev->max_timeout = 10 * IR_DEFAULT_TIMEOUT;
- if (pdata->allowed_protos)
- rcdev->allowed_protocols = pdata->allowed_protos;
- else
-@@ -154,6 +172,9 @@ static int gpio_ir_recv_probe(struct pla
- gpio_dev->gpio_nr = pdata->gpio_nr;
- gpio_dev->active_low = pdata->active_low;
-
-+ setup_timer(&gpio_dev->flush_timer, flush_timer,
-+ (unsigned long)gpio_dev);
-+
- rc = gpio_request(pdata->gpio_nr, "gpio-ir-recv");
- if (rc < 0)
- goto err_gpio_request;
-@@ -196,6 +217,7 @@ static int gpio_ir_recv_remove(struct pl
- struct gpio_rc_dev *gpio_dev = platform_get_drvdata(pdev);
-
- free_irq(gpio_to_irq(gpio_dev->gpio_nr), gpio_dev);
-+ del_timer_sync(&gpio_dev->flush_timer);
- rc_unregister_device(gpio_dev->rcdev);
- gpio_free(gpio_dev->gpio_nr);
- kfree(gpio_dev);
diff --git a/target/linux/brcm2708/patches-4.4/0379-smsir.h-remove-a-now-duplicated-definition-IR_DEFAUL.patch b/target/linux/brcm2708/patches-4.4/0379-smsir.h-remove-a-now-duplicated-definition-IR_DEFAUL.patch
deleted file mode 100644
index 15dcc4d..0000000
--- a/target/linux/brcm2708/patches-4.4/0379-smsir.h-remove-a-now-duplicated-definition-IR_DEFAUL.patch
+++ /dev/null
@@ -1,24 +0,0 @@
-From 2809beb6706e6d2e445f8318401b03f6bac82d72 Mon Sep 17 00:00:00 2001
-From: Mauro Carvalho Chehab <mchehab at osg.samsung.com>
-Date: Thu, 19 Nov 2015 11:41:36 -0200
-Subject: [PATCH] smsir.h: remove a now duplicated definition
- (IR_DEFAULT_TIMEOUT)
-
-This macro is now part of the core. Remove from Siano driver.
-
-Signed-off-by: Mauro Carvalho Chehab <mchehab at osg.samsung.com>
----
- drivers/media/common/siano/smsir.h | 2 --
- 1 file changed, 2 deletions(-)
-
---- a/drivers/media/common/siano/smsir.h
-+++ b/drivers/media/common/siano/smsir.h
-@@ -30,8 +30,6 @@ along with this program. If not, see <h
- #include <linux/input.h>
- #include <media/rc-core.h>
-
--#define IR_DEFAULT_TIMEOUT 100
--
- struct smscore_device_t;
-
- struct ir_t {
diff --git a/target/linux/brcm2708/patches-4.4/0380-Implement-a-wakeup-source-option-for-the-i2c-rtc-Dev.patch b/target/linux/brcm2708/patches-4.4/0380-Implement-a-wakeup-source-option-for-the-i2c-rtc-Dev.patch
deleted file mode 100644
index 7fa529b..0000000
--- a/target/linux/brcm2708/patches-4.4/0380-Implement-a-wakeup-source-option-for-the-i2c-rtc-Dev.patch
+++ /dev/null
@@ -1,36 +0,0 @@
-From c07a798c0570158e07eea5e6485a6018b4e418e6 Mon Sep 17 00:00:00 2001
-From: Nicolas Boullis <nboullis at debian.org>
-Date: Sat, 4 Jun 2016 00:57:06 +0200
-Subject: [PATCH] Implement a "wakeup-source" option for the i2c-rtc DeviceTree
- overlay.
-
-See: https://github.com/raspberrypi/linux/pull/1511
----
- arch/arm/boot/dts/overlays/README | 3 +++
- arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts | 4 ++++
- 2 files changed, 7 insertions(+)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -445,6 +445,9 @@ Params: ds1307 Select t
-
- trickle-resistor-ohms Resistor value for trickle charge (DS1339-only)
-
-+ wakeup-source Specify that the RTC can be used as a wakeup
-+ source
-+
-
- Name: i2c0-bcm2708
- Info: Enable the i2c_bcm2708 driver for the i2c0 bus. Not all pin combinations
---- a/arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts
-@@ -65,5 +65,9 @@
- pcf8523 = <&pcf8523>,"status";
- pcf8563 = <&pcf8563>,"status";
- trickle-resistor-ohms = <&ds1339>,"trickle-resistor-ohms:0";
-+ wakeup-source = <&ds1339>,"wakeup-source?",
-+ <&ds3231>,"wakeup-source?",
-+ <&mcp7940x>,"wakeup-source?",
-+ <&mcp7941x>,"wakeup-source?";
- };
- };
diff --git a/target/linux/brcm2708/patches-4.4/0381-BCM270X_DT-Fix-rpi-dac-overlay.patch b/target/linux/brcm2708/patches-4.4/0381-BCM270X_DT-Fix-rpi-dac-overlay.patch
deleted file mode 100644
index e98da46..0000000
--- a/target/linux/brcm2708/patches-4.4/0381-BCM270X_DT-Fix-rpi-dac-overlay.patch
+++ /dev/null
@@ -1,34 +0,0 @@
-From f3fc891572c8b371746bf05419da57a4337d9090 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 3 Jun 2016 21:56:40 +0100
-Subject: [PATCH] BCM270X_DT: Fix rpi-dac overlay
-
-The rpi-dac overlay is almost identical to the hifiberry-dac overlay -
-the codec used is different but it also doesn't sit on the I2C bus. As
-a result, when the overlays were modified for dynamic loading and it
-was discovered that the hifiberry-dac overlay didn't work any more, the
-the rpi-dac overlay was also broken.
-
-The failure was caused by the fact that outside a bus, device names are
-constructed from the concatenation of the path elements leading to it,
-so moving the codec instantiation inside /soc caused the device name
-to get a "soc" added, breaking ALSA's naming.
-
-See: http://forum.kodi.tv/showthread.php?tid=269814&pid=2349776#pid2349776
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/overlays/rpi-dac-overlay.dts | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/arch/arm/boot/dts/overlays/rpi-dac-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/rpi-dac-overlay.dts
-@@ -13,7 +13,7 @@
- };
-
- fragment at 1 {
-- target = <&soc>;
-+ target-path = "/";
- __overlay__ {
- pcm1794a-codec {
- #sound-dai-cells = <0>;
diff --git a/target/linux/brcm2708/patches-4.4/0382-BCM270X_DT-Make-i2c-gpio-usable-by-other-overlays.patch b/target/linux/brcm2708/patches-4.4/0382-BCM270X_DT-Make-i2c-gpio-usable-by-other-overlays.patch
deleted file mode 100644
index ed472c2..0000000
--- a/target/linux/brcm2708/patches-4.4/0382-BCM270X_DT-Make-i2c-gpio-usable-by-other-overlays.patch
+++ /dev/null
@@ -1,37 +0,0 @@
-From e1174e6896bbdb39c5d45322819a70b23a57d32f Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 6 Jun 2016 09:23:37 +0100
-Subject: [PATCH] BCM270X_DT: Make i2c-gpio usable by other overlays
-
-Modify the i2c-gpio overlay to export symbol i2c-gpio for use by other
-overlays. Export the alias as well for good measure.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/overlays/i2c-gpio-overlay.dts | 15 +++++++++++++++
- 1 file changed, 15 insertions(+)
-
---- a/arch/arm/boot/dts/overlays/i2c-gpio-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/i2c-gpio-overlay.dts
-@@ -19,6 +19,21 @@
- };
- };
- };
-+
-+ fragment at 1 {
-+ target-path = "/aliases";
-+ __overlay__ {
-+ i2c_gpio = "/i2c at 0";
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target-path = "/__symbols__";
-+ __overlay__ {
-+ i2c_gpio = "/i2c at 0";
-+ };
-+ };
-+
- __overrides__ {
- i2c_gpio_sda = <&i2c_gpio>,"gpios:4";
- i2c_gpio_scl = <&i2c_gpio>,"gpios:16";
diff --git a/target/linux/brcm2708/patches-4.4/0386-Add-ads1015-overlay.patch b/target/linux/brcm2708/patches-4.4/0386-Add-ads1015-overlay.patch
deleted file mode 100644
index 6684ab5..0000000
--- a/target/linux/brcm2708/patches-4.4/0386-Add-ads1015-overlay.patch
+++ /dev/null
@@ -1,155 +0,0 @@
-From 4528d92a0ea8014a42526215872faf89c7a4c619 Mon Sep 17 00:00:00 2001
-From: Erik Sejr <erik at eriks.ssimicro.com>
-Date: Tue, 7 Jun 2016 20:58:17 -0400
-Subject: [PATCH] Add ads1015 overlay
-
-See: https://github.com/raspberrypi/linux/pull/1520
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 22 ++++++
- arch/arm/boot/dts/overlays/ads1015-overlay.dts | 98 ++++++++++++++++++++++++++
- 3 files changed, 121 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/ads1015-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -13,6 +13,7 @@ ifeq ($(CONFIG_ARCH_BCM2835),y)
- endif
-
- dtbo-$(RPI_DT_OVERLAYS) += adau1977-adc.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += ads1015.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += ads7846.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += akkordion-iqdacplus.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += at86rf233.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -168,6 +168,28 @@ Load: dtoverlay=adau1977-adc
- Params: <None>
-
-
-+Name: ads1015
-+Info: Overlay for activation of Texas Instruments ADS1015 ADC over I2C
-+Load: dtoverlay=ads1015,<param>=<val>
-+Params: addr I2C bus address of device. Set based on how the
-+ addr pin is wired. (default=0x48 assumes addr
-+ is pulled to GND)
-+ cha_enable Enable virtual channel a. (default=true)
-+ cha_cfg Set the configuration for virtual channel a.
-+ (default=4 configures this channel for the
-+ voltage at A0 with respect to GND)
-+ cha_datarate Set the datarate (samples/sec) for this channel.
-+ (default=4 sets 1600 sps)
-+ cha_gain Set the gain of the Programmable Gain
-+ Amplifier for this channel. (default=2 sets the
-+ full scale of the channel to 2.048 Volts)
-+
-+ Channel (ch) parameters can be set for each enabled channel.
-+ A maximum of 4 channels can be enabled (letters a thru d).
-+ For more information refer to the device datasheet at:
-+ http://www.ti.com/lit/ds/symlink/ads1015.pdf
-+
-+
- Name: ads7846
- Info: ADS7846 Touch controller
- Load: dtoverlay=ads7846,<param>=<val>
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/ads1015-overlay.dts
-@@ -0,0 +1,98 @@
-+/*
-+ * 2016 - Erik Sejr
-+ */
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+ /* ----------- ADS1015 ------------ */
-+ fragment at 0 {
-+ target = <&i2c_arm>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+ ads1015: ads1015 {
-+ compatible = "ti,ads1015";
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <0x48>;
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target-path = "i2c_arm/ads1015";
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ channel_a: channel_a {
-+ reg = <4>;
-+ ti,gain = <2>;
-+ ti,datarate = <4>;
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target-path = "i2c_arm/ads1015";
-+ __dormant__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ channel_b: channel_b {
-+ reg = <5>;
-+ ti,gain = <2>;
-+ ti,datarate = <4>;
-+ };
-+ };
-+ };
-+
-+ fragment at 3 {
-+ target-path = "i2c_arm/ads1015";
-+ __dormant__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ channel_c: channel_c {
-+ reg = <6>;
-+ ti,gain = <2>;
-+ ti,datarate = <4>;
-+ };
-+ };
-+ };
-+
-+ fragment at 4 {
-+ target-path = "i2c_arm/ads1015";
-+ __dormant__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ channel_d: channel_d {
-+ reg = <7>;
-+ ti,gain = <2>;
-+ ti,datarate = <4>;
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ addr = <&ads1015>,"reg:0";
-+ cha_enable = <0>,"=1";
-+ cha_cfg = <&channel_a>,"reg:0";
-+ cha_gain = <&channel_a>,"ti,gain:0";
-+ cha_datarate = <&channel_a>,"ti,datarate:0";
-+ chb_enable = <0>,"=2";
-+ chb_cfg = <&channel_b>,"reg:0";
-+ chb_gain = <&channel_b>,"ti,gain:0";
-+ chb_datarate = <&channel_b>,"ti,datarate:0";
-+ chc_enable = <0>,"=3";
-+ chc_cfg = <&channel_c>,"reg:0";
-+ chc_gain = <&channel_c>,"ti,gain:0";
-+ chc_datarate = <&channel_c>,"ti,datarate:0";
-+ chd_enable = <0>,"=4";
-+ chd_cfg = <&channel_d>,"reg:0";
-+ chd_gain = <&channel_d>,"ti,gain:0";
-+ chd_datarate = <&channel_d>,"ti,datarate:0";
-+ };
-+
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0387-Fixed-MCP23017-section-in-overlay-README.patch b/target/linux/brcm2708/patches-4.4/0387-Fixed-MCP23017-section-in-overlay-README.patch
deleted file mode 100644
index 6454d72..0000000
--- a/target/linux/brcm2708/patches-4.4/0387-Fixed-MCP23017-section-in-overlay-README.patch
+++ /dev/null
@@ -1,22 +0,0 @@
-From 92e11a94e6e81e5b9358f65989641ffbedc24241 Mon Sep 17 00:00:00 2001
-From: Michael Kaplan <m.kaplan at evva.com>
-Date: Wed, 8 Jun 2016 15:14:11 +0200
-Subject: [PATCH] Fixed MCP23017 section in overlay README
-
-Old description could have led to the misunderstanding that it is an
-i2c port expander, but in fact it is a gpio expander.
----
- arch/arm/boot/dts/overlays/README | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -595,7 +595,7 @@ Params: gpio_out_pin GPIO for
-
-
- Name: mcp23017
--Info: Configures the MCP23017 I2C port expander
-+Info: Configures the MCP23017 I2C GPIO expander
- Load: dtoverlay=mcp23017,<param>=<val>
- Params: gpiopin Gpio pin connected to the INTA output of the
- MCP23017 (default: 4)
diff --git a/target/linux/brcm2708/patches-4.4/0388-Revert-bcm2835-dma-Fix-up-convert-to-DMA-pool.patch b/target/linux/brcm2708/patches-4.4/0388-Revert-bcm2835-dma-Fix-up-convert-to-DMA-pool.patch
deleted file mode 100644
index 0e0f2bd..0000000
--- a/target/linux/brcm2708/patches-4.4/0388-Revert-bcm2835-dma-Fix-up-convert-to-DMA-pool.patch
+++ /dev/null
@@ -1,86 +0,0 @@
-From e21e533fa2f97f934376556d033f24e24edb362a Mon Sep 17 00:00:00 2001
-From: Martin Sperl <kernel at martin.sperl.org>
-Date: Fri, 22 Apr 2016 17:17:13 +0000
-Subject: [PATCH] Revert "bcm2835-dma: Fix up convert to DMA pool"
-
-This reverts commit ec2e48fda22c57cab56a4332d1a095f91c919493.
----
- drivers/dma/bcm2835-dma.c | 36 ++++++++++--------------------------
- 1 file changed, 10 insertions(+), 26 deletions(-)
-
---- a/drivers/dma/bcm2835-dma.c
-+++ b/drivers/dma/bcm2835-dma.c
-@@ -488,17 +488,6 @@ static struct dma_async_tx_descriptor *b
- c->cyclic = true;
-
- return vchan_tx_prep(&c->vc, &d->vd, flags);
--error_cb:
-- i--;
-- for (; i >= 0; i--) {
-- struct bcm2835_cb_entry *cb_entry = &d->cb_list[i];
--
-- dma_pool_free(c->cb_pool, cb_entry->cb, cb_entry->paddr);
-- }
--
-- kfree(d->cb_list);
-- kfree(d);
-- return NULL;
- }
-
- static struct dma_async_tx_descriptor *
-@@ -545,7 +534,6 @@ bcm2835_dma_prep_slave_sg(struct dma_cha
- if (!d)
- return NULL;
-
-- d->c = c;
- d->dir = direction;
-
- if (c->ch >= 8) /* LITE channel */
-@@ -565,21 +553,15 @@ bcm2835_dma_prep_slave_sg(struct dma_cha
- d->frames += len / max_size + 1;
- }
-
-- d->cb_list = kcalloc(d->frames, sizeof(*d->cb_list), GFP_KERNEL);
-- if (!d->cb_list) {
-+ /* Allocate memory for control blocks */
-+ d->control_block_size = d->frames * sizeof(struct bcm2835_dma_cb);
-+ d->control_block_base = dma_zalloc_coherent(chan->device->dev,
-+ d->control_block_size, &d->control_block_base_phys,
-+ GFP_NOWAIT);
-+ if (!d->control_block_base) {
- kfree(d);
- return NULL;
- }
-- /* Allocate memory for control blocks */
-- for (i = 0; i < d->frames; i++) {
-- struct bcm2835_cb_entry *cb_entry = &d->cb_list[i];
--
-- cb_entry->cb = dma_pool_zalloc(c->cb_pool, GFP_ATOMIC,
-- &cb_entry->paddr);
--
-- if (!cb_entry->cb)
-- goto error_cb;
-- }
-
- /*
- * Iterate over all SG entries, create a control block
-@@ -596,7 +578,7 @@ bcm2835_dma_prep_slave_sg(struct dma_cha
-
- for (j = 0; j < len; j += max_size) {
- struct bcm2835_dma_cb *control_block =
-- d->cb_list[i + split_cnt].cb;
-+ &d->control_block_base[i + split_cnt];
-
- /* Setup addresses */
- if (d->dir == DMA_DEV_TO_MEM) {
-@@ -638,7 +620,9 @@ bcm2835_dma_prep_slave_sg(struct dma_cha
- if (i < sg_len - 1 || len - j > max_size) {
- /* Next block is the next frame. */
- control_block->next =
-- d->cb_list[i + split_cnt + 1].paddr;
-+ d->control_block_base_phys +
-+ sizeof(struct bcm2835_dma_cb) *
-+ (i + split_cnt + 1);
- } else {
- /* Next block is empty. */
- control_block->next = 0;
diff --git a/target/linux/brcm2708/patches-4.4/0389-Revert-bcm2835-dma-Limit-cyclic-transfers-on-lite-ch.patch b/target/linux/brcm2708/patches-4.4/0389-Revert-bcm2835-dma-Limit-cyclic-transfers-on-lite-ch.patch
deleted file mode 100644
index 7627c55..0000000
--- a/target/linux/brcm2708/patches-4.4/0389-Revert-bcm2835-dma-Limit-cyclic-transfers-on-lite-ch.patch
+++ /dev/null
@@ -1,35 +0,0 @@
-From 6973f7462577fb7bdcf4d04901346462d645fcd7 Mon Sep 17 00:00:00 2001
-From: Martin Sperl <kernel at martin.sperl.org>
-Date: Fri, 22 Apr 2016 17:17:22 +0000
-Subject: [PATCH] Revert "bcm2835-dma: Limit cyclic transfers on lite channels
- to 32k"
-
-This reverts commit 052c2005b6ecedc5abad86632f5781adda310aa7.
----
- drivers/dma/bcm2835-dma.c | 8 +-------
- 1 file changed, 1 insertion(+), 7 deletions(-)
-
---- a/drivers/dma/bcm2835-dma.c
-+++ b/drivers/dma/bcm2835-dma.c
-@@ -144,12 +144,6 @@ struct bcm2835_desc {
- */
- #define MAX_LITE_TRANSFER (SZ_64K - 4)
-
--/*
-- * Transfers larger than 32k cause issues with the bcm2708-i2s driver,
-- * so limit transfer size to 32k as bcm2708-dmaengine did.
-- */
--#define MAX_CYCLIC_LITE_TRANSFER SZ_32K
--
- static inline struct bcm2835_dmadev *to_bcm2835_dma_dev(struct dma_device *d)
- {
- return container_of(d, struct bcm2835_dmadev, ddev);
-@@ -418,7 +412,7 @@ static struct dma_async_tx_descriptor *b
- d->c = c;
- d->dir = direction;
- if (c->ch >= 8) /* LITE channel */
-- max_size = MAX_CYCLIC_LITE_TRANSFER;
-+ max_size = MAX_LITE_TRANSFER;
- else
- max_size = MAX_NORMAL_TRANSFER;
- period_len = min(period_len, max_size);
diff --git a/target/linux/brcm2708/patches-4.4/0390-Revert-dmaengine-bcm2835-Load-driver-early-and-suppo.patch b/target/linux/brcm2708/patches-4.4/0390-Revert-dmaengine-bcm2835-Load-driver-early-and-suppo.patch
deleted file mode 100644
index a7e4daa..0000000
--- a/target/linux/brcm2708/patches-4.4/0390-Revert-dmaengine-bcm2835-Load-driver-early-and-suppo.patch
+++ /dev/null
@@ -1,90 +0,0 @@
-From 7dd4ef8796bac4137484f636a04b02fba85537dc Mon Sep 17 00:00:00 2001
-From: Martin Sperl <kernel at martin.sperl.org>
-Date: Fri, 22 Apr 2016 17:17:30 +0000
-Subject: [PATCH] Revert "dmaengine: bcm2835: Load driver early and support
- legacy API"
-
-This reverts commit 6f56fff39c811953809b011f59c49a2122c4d173.
----
- drivers/dma/Kconfig | 2 +-
- drivers/dma/bcm2835-dma.c | 30 ++++++------------------------
- 2 files changed, 7 insertions(+), 25 deletions(-)
-
---- a/drivers/dma/Kconfig
-+++ b/drivers/dma/Kconfig
-@@ -108,7 +108,7 @@ config COH901318
-
- config DMA_BCM2835
- tristate "BCM2835 DMA engine support"
-- depends on ARCH_BCM2835 || ARCH_BCM2708 || ARCH_BCM2709
-+ depends on ARCH_BCM2835
- select DMA_ENGINE
- select DMA_VIRTUAL_CHANNELS
-
---- a/drivers/dma/bcm2835-dma.c
-+++ b/drivers/dma/bcm2835-dma.c
-@@ -36,7 +36,6 @@
- #include <linux/interrupt.h>
- #include <linux/list.h>
- #include <linux/module.h>
--#include <linux/platform_data/dma-bcm2708.h>
- #include <linux/platform_device.h>
- #include <linux/slab.h>
- #include <linux/io.h>
-@@ -787,10 +786,6 @@ static int bcm2835_dma_probe(struct plat
- if (IS_ERR(base))
- return PTR_ERR(base);
-
-- rc = bcm_dmaman_probe(pdev, base, BCM2835_DMA_BULK_MASK);
-- if (rc)
-- dev_err(&pdev->dev, "Failed to initialize the legacy API\n");
--
- od->base = base;
-
- dma_cap_set(DMA_SLAVE, od->ddev.cap_mask);
-@@ -823,8 +818,11 @@ static int bcm2835_dma_probe(struct plat
- goto err_no_dma;
- }
-
-- /* Channel 0 is used by the legacy API */
-- chans_available &= ~BCM2835_DMA_BULK_MASK;
-+ /*
-+ * Do not use the FIQ and BULK channels,
-+ * because they are used by the GPU.
-+ */
-+ chans_available &= ~(BCM2835_DMA_FIQ_MASK | BCM2835_DMA_BULK_MASK);
-
- for (i = 0; i < pdev->num_resources; i++) {
- irq = platform_get_irq(pdev, i);
-@@ -868,7 +866,6 @@ static int bcm2835_dma_remove(struct pla
- {
- struct bcm2835_dmadev *od = platform_get_drvdata(pdev);
-
-- bcm_dmaman_remove(pdev);
- dma_async_device_unregister(&od->ddev);
- bcm2835_dma_free(od);
-
-@@ -884,22 +881,7 @@ static struct platform_driver bcm2835_dm
- },
- };
-
--static int bcm2835_dma_init(void)
--{
-- return platform_driver_register(&bcm2835_dma_driver);
--}
--
--static void bcm2835_dma_exit(void)
--{
-- platform_driver_unregister(&bcm2835_dma_driver);
--}
--
--/*
-- * Load after serial driver (arch_initcall) so we see the messages if it fails,
-- * but before drivers (module_init) that need a DMA channel.
-- */
--subsys_initcall(bcm2835_dma_init);
--module_exit(bcm2835_dma_exit);
-+module_platform_driver(bcm2835_dma_driver);
-
- MODULE_ALIAS("platform:bcm2835-dma");
- MODULE_DESCRIPTION("BCM2835 DMA engine driver");
diff --git a/target/linux/brcm2708/patches-4.4/0391-Revert-dmaengine-bcm2835-Add-slave-dma-support.patch b/target/linux/brcm2708/patches-4.4/0391-Revert-dmaengine-bcm2835-Add-slave-dma-support.patch
deleted file mode 100644
index 08b375b..0000000
--- a/target/linux/brcm2708/patches-4.4/0391-Revert-dmaengine-bcm2835-Add-slave-dma-support.patch
+++ /dev/null
@@ -1,312 +0,0 @@
-From 7ed4a7651d05de05a1caaa2617255a23ac7f78b1 Mon Sep 17 00:00:00 2001
-From: Martin Sperl <kernel at martin.sperl.org>
-Date: Fri, 22 Apr 2016 17:17:37 +0000
-Subject: [PATCH] Revert "dmaengine: bcm2835: Add slave dma support"
-
-This reverts commit 8a349301238aabb40c9da5ca8c8492b6b8d146f6.
----
- drivers/dma/bcm2835-dma.c | 206 ++++------------------------------------------
- 1 file changed, 14 insertions(+), 192 deletions(-)
-
---- a/drivers/dma/bcm2835-dma.c
-+++ b/drivers/dma/bcm2835-dma.c
-@@ -1,10 +1,11 @@
- /*
- * BCM2835 DMA engine support
- *
-+ * This driver only supports cyclic DMA transfers
-+ * as needed for the I2S module.
-+ *
- * Author: Florian Meier <florian.meier at koalo.de>
- * Copyright 2013
-- * Gellert Weisz <gellert at raspberrypi.org>
-- * Copyright 2013-2014
- *
- * Based on
- * OMAP DMAengine support by Russell King
-@@ -94,8 +95,6 @@ struct bcm2835_desc {
- size_t size;
- };
-
--#define BCM2835_DMA_WAIT_CYCLES 0 /* Slow down DMA transfers: 0-31 */
--
- #define BCM2835_DMA_CS 0x00
- #define BCM2835_DMA_ADDR 0x04
- #define BCM2835_DMA_SOURCE_AD 0x0c
-@@ -112,16 +111,12 @@ struct bcm2835_desc {
- #define BCM2835_DMA_RESET BIT(31) /* WO, self clearing */
-
- #define BCM2835_DMA_INT_EN BIT(0)
--#define BCM2835_DMA_WAIT_RESP BIT(3)
- #define BCM2835_DMA_D_INC BIT(4)
--#define BCM2835_DMA_D_WIDTH BIT(5)
- #define BCM2835_DMA_D_DREQ BIT(6)
- #define BCM2835_DMA_S_INC BIT(8)
--#define BCM2835_DMA_S_WIDTH BIT(9)
- #define BCM2835_DMA_S_DREQ BIT(10)
-
- #define BCM2835_DMA_PER_MAP(x) ((x) << 16)
--#define BCM2835_DMA_WAITS(x) (((x) & 0x1f) << 21)
-
- #define BCM2835_DMA_DATA_TYPE_S8 1
- #define BCM2835_DMA_DATA_TYPE_S16 2
-@@ -135,14 +130,6 @@ struct bcm2835_desc {
- #define BCM2835_DMA_CHAN(n) ((n) << 8) /* Base address */
- #define BCM2835_DMA_CHANIO(base, n) ((base) + BCM2835_DMA_CHAN(n))
-
--#define MAX_NORMAL_TRANSFER SZ_1G
--/*
-- * Max length on a Lite channel is 65535 bytes.
-- * DMA handles byte-enables on SDRAM reads and writes even on 128-bit accesses,
-- * but byte-enables don't exist on peripheral addresses, so align to 32-bit.
-- */
--#define MAX_LITE_TRANSFER (SZ_64K - 4)
--
- static inline struct bcm2835_dmadev *to_bcm2835_dma_dev(struct dma_device *d)
- {
- return container_of(d, struct bcm2835_dmadev, ddev);
-@@ -239,19 +226,13 @@ static irqreturn_t bcm2835_dma_callback(
- d = c->desc;
-
- if (d) {
-- if (c->cyclic) {
-- vchan_cyclic_callback(&d->vd);
--
-- /* Keep the DMA engine running */
-- writel(BCM2835_DMA_ACTIVE,
-- c->chan_base + BCM2835_DMA_CS);
--
-- } else {
-- vchan_cookie_complete(&c->desc->vd);
-- bcm2835_dma_start_desc(c);
-- }
-+ /* TODO Only works for cyclic DMA */
-+ vchan_cyclic_callback(&d->vd);
- }
-
-+ /* Keep the DMA engine running */
-+ writel(BCM2835_DMA_ACTIVE, c->chan_base + BCM2835_DMA_CS);
-+
- spin_unlock_irqrestore(&c->vc.lock, flags);
-
- return IRQ_HANDLED;
-@@ -358,6 +339,8 @@ static void bcm2835_dma_issue_pending(st
- struct bcm2835_chan *c = to_bcm2835_dma_chan(chan);
- unsigned long flags;
-
-+ c->cyclic = true; /* Nothing else is implemented */
-+
- spin_lock_irqsave(&c->vc.lock, flags);
- if (vchan_issue_pending(&c->vc) && !c->desc)
- bcm2835_dma_start_desc(c);
-@@ -375,7 +358,7 @@ static struct dma_async_tx_descriptor *b
- struct bcm2835_desc *d;
- dma_addr_t dev_addr;
- unsigned int es, sync_type;
-- unsigned int frame, max_size;
-+ unsigned int frame;
- int i;
-
- /* Grab configuration */
-@@ -410,12 +393,7 @@ static struct dma_async_tx_descriptor *b
-
- d->c = c;
- d->dir = direction;
-- if (c->ch >= 8) /* LITE channel */
-- max_size = MAX_LITE_TRANSFER;
-- else
-- max_size = MAX_NORMAL_TRANSFER;
-- period_len = min(period_len, max_size);
-- d->frames = (buf_len - 1) / (period_len + 1);
-+ d->frames = buf_len / period_len;
-
- d->cb_list = kcalloc(d->frames, sizeof(*d->cb_list), GFP_KERNEL);
- if (!d->cb_list) {
-@@ -463,171 +441,17 @@ static struct dma_async_tx_descriptor *b
- BCM2835_DMA_PER_MAP(c->dreq);
-
- /* Length of a frame */
-- if (frame != d->frames - 1)
-- control_block->length = period_len;
-- else
-- control_block->length = buf_len - (d->frames - 1) *
-- period_len;
-+ control_block->length = period_len;
- d->size += control_block->length;
-
- /*
- * Next block is the next frame.
-- * This function is called on cyclic DMA transfers.
-+ * This DMA engine driver currently only supports cyclic DMA.
- * Therefore, wrap around at number of frames.
- */
- control_block->next = d->cb_list[((frame + 1) % d->frames)].paddr;
- }
-
-- c->cyclic = true;
--
-- return vchan_tx_prep(&c->vc, &d->vd, flags);
--}
--
--static struct dma_async_tx_descriptor *
--bcm2835_dma_prep_slave_sg(struct dma_chan *chan,
-- struct scatterlist *sgl,
-- unsigned int sg_len,
-- enum dma_transfer_direction direction,
-- unsigned long flags, void *context)
--{
-- struct bcm2835_chan *c = to_bcm2835_dma_chan(chan);
-- enum dma_slave_buswidth dev_width;
-- struct bcm2835_desc *d;
-- dma_addr_t dev_addr;
-- struct scatterlist *sgent;
-- unsigned int i, sync_type, split_cnt, max_size;
--
-- if (!is_slave_direction(direction)) {
-- dev_err(chan->device->dev, "direction not supported\n");
-- return NULL;
-- }
--
-- if (direction == DMA_DEV_TO_MEM) {
-- dev_addr = c->cfg.src_addr;
-- dev_width = c->cfg.src_addr_width;
-- sync_type = BCM2835_DMA_S_DREQ;
-- } else {
-- dev_addr = c->cfg.dst_addr;
-- dev_width = c->cfg.dst_addr_width;
-- sync_type = BCM2835_DMA_D_DREQ;
-- }
--
-- /* Bus width translates to the element size (ES) */
-- switch (dev_width) {
-- case DMA_SLAVE_BUSWIDTH_4_BYTES:
-- break;
-- default:
-- dev_err(chan->device->dev, "buswidth not supported: %i\n",
-- dev_width);
-- return NULL;
-- }
--
-- /* Allocate and setup the descriptor. */
-- d = kzalloc(sizeof(*d), GFP_NOWAIT);
-- if (!d)
-- return NULL;
--
-- d->dir = direction;
--
-- if (c->ch >= 8) /* LITE channel */
-- max_size = MAX_LITE_TRANSFER;
-- else
-- max_size = MAX_NORMAL_TRANSFER;
--
-- /*
-- * Store the length of the SG list in d->frames
-- * taking care to account for splitting up transfers
-- * too large for a LITE channel
-- */
-- d->frames = 0;
-- for_each_sg(sgl, sgent, sg_len, i) {
-- unsigned int len = sg_dma_len(sgent);
--
-- d->frames += len / max_size + 1;
-- }
--
-- /* Allocate memory for control blocks */
-- d->control_block_size = d->frames * sizeof(struct bcm2835_dma_cb);
-- d->control_block_base = dma_zalloc_coherent(chan->device->dev,
-- d->control_block_size, &d->control_block_base_phys,
-- GFP_NOWAIT);
-- if (!d->control_block_base) {
-- kfree(d);
-- return NULL;
-- }
--
-- /*
-- * Iterate over all SG entries, create a control block
-- * for each frame and link them together.
-- * Count the number of times an SG entry had to be split
-- * as a result of using a LITE channel
-- */
-- split_cnt = 0;
--
-- for_each_sg(sgl, sgent, sg_len, i) {
-- unsigned int j;
-- dma_addr_t addr = sg_dma_address(sgent);
-- unsigned int len = sg_dma_len(sgent);
--
-- for (j = 0; j < len; j += max_size) {
-- struct bcm2835_dma_cb *control_block =
-- &d->control_block_base[i + split_cnt];
--
-- /* Setup addresses */
-- if (d->dir == DMA_DEV_TO_MEM) {
-- control_block->info = BCM2835_DMA_D_INC |
-- BCM2835_DMA_D_WIDTH |
-- BCM2835_DMA_S_DREQ;
-- control_block->src = dev_addr;
-- control_block->dst = addr + (dma_addr_t)j;
-- } else {
-- control_block->info = BCM2835_DMA_S_INC |
-- BCM2835_DMA_S_WIDTH |
-- BCM2835_DMA_D_DREQ;
-- control_block->src = addr + (dma_addr_t)j;
-- control_block->dst = dev_addr;
-- }
--
-- /* Common part */
-- control_block->info |=
-- BCM2835_DMA_WAITS(BCM2835_DMA_WAIT_CYCLES);
-- control_block->info |= BCM2835_DMA_WAIT_RESP;
--
-- /* Enable */
-- if (i == sg_len - 1 && len - j <= max_size)
-- control_block->info |= BCM2835_DMA_INT_EN;
--
-- /* Setup synchronization */
-- if (sync_type)
-- control_block->info |= sync_type;
--
-- /* Setup DREQ channel */
-- if (c->dreq)
-- control_block->info |=
-- BCM2835_DMA_PER_MAP(c->dreq);
--
-- /* Length of a frame */
-- control_block->length = min(len - j, max_size);
-- d->size += control_block->length;
--
-- if (i < sg_len - 1 || len - j > max_size) {
-- /* Next block is the next frame. */
-- control_block->next =
-- d->control_block_base_phys +
-- sizeof(struct bcm2835_dma_cb) *
-- (i + split_cnt + 1);
-- } else {
-- /* Next block is empty. */
-- control_block->next = 0;
-- }
--
-- if (len - j > max_size)
-- split_cnt++;
-- }
-- }
--
-- c->cyclic = false;
--
- return vchan_tx_prep(&c->vc, &d->vd, flags);
- error_cb:
- i--;
-@@ -796,7 +620,6 @@ static int bcm2835_dma_probe(struct plat
- od->ddev.device_tx_status = bcm2835_dma_tx_status;
- od->ddev.device_issue_pending = bcm2835_dma_issue_pending;
- od->ddev.device_prep_dma_cyclic = bcm2835_dma_prep_dma_cyclic;
-- od->ddev.device_prep_slave_sg = bcm2835_dma_prep_slave_sg;
- od->ddev.device_config = bcm2835_dma_slave_config;
- od->ddev.device_terminate_all = bcm2835_dma_terminate_all;
- od->ddev.src_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_4_BYTES);
-@@ -886,5 +709,4 @@ module_platform_driver(bcm2835_dma_drive
- MODULE_ALIAS("platform:bcm2835-dma");
- MODULE_DESCRIPTION("BCM2835 DMA engine driver");
- MODULE_AUTHOR("Florian Meier <florian.meier at koalo.de>");
--MODULE_AUTHOR("Gellert Weisz <gellert at raspberrypi.org>");
- MODULE_LICENSE("GPL v2");
diff --git a/target/linux/brcm2708/patches-4.4/0392-dmaengine-bcm2835-remove-unnecessary-masking-of-dma-.patch b/target/linux/brcm2708/patches-4.4/0392-dmaengine-bcm2835-remove-unnecessary-masking-of-dma-.patch
deleted file mode 100644
index 632b697..0000000
--- a/target/linux/brcm2708/patches-4.4/0392-dmaengine-bcm2835-remove-unnecessary-masking-of-dma-.patch
+++ /dev/null
@@ -1,56 +0,0 @@
-From 4373ba9e686948c9188a594f63ecb57569ff972b Mon Sep 17 00:00:00 2001
-From: Martin Sperl <kernel at martin.sperl.org>
-Date: Wed, 16 Mar 2016 12:24:56 -0700
-Subject: [PATCH] dmaengine: bcm2835: remove unnecessary masking of dma
- channels
-
-The original patch contained 3 dma channels that were masked out.
-
-These - as far as research and discussions show - are a
-artefacts remaining from the downstream legacy dma-api.
-
-Right now down-stream still includes a legacy api used only
-in a single (downstream only) driver (bcm2708_fb) that requires
-2D DMA for speedup (DMA-channel 0).
-Formerly the sd-card support driver also was using this legacy
-api (DMA-channel 2), but since has been moved over to use
-dmaengine directly.
-
-The DMA-channel 3 is already masked out in the devicetree in
-the default property "brcm,dma-channel-mask = <0x7f35>;"
-
-So we can remove the whole masking of DMA channels.
-
-Signed-off-by: Martin Sperl <kernel at martin.sperl.org>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Vinod Koul <vinod.koul at intel.com>
----
- drivers/dma/bcm2835-dma.c | 9 ---------
- 1 file changed, 9 deletions(-)
-
---- a/drivers/dma/bcm2835-dma.c
-+++ b/drivers/dma/bcm2835-dma.c
-@@ -123,9 +123,6 @@ struct bcm2835_desc {
- #define BCM2835_DMA_DATA_TYPE_S32 4
- #define BCM2835_DMA_DATA_TYPE_S128 16
-
--#define BCM2835_DMA_BULK_MASK BIT(0)
--#define BCM2835_DMA_FIQ_MASK (BIT(2) | BIT(3))
--
- /* Valid only for channels 0 - 14, 15 has its own base address */
- #define BCM2835_DMA_CHAN(n) ((n) << 8) /* Base address */
- #define BCM2835_DMA_CHANIO(base, n) ((base) + BCM2835_DMA_CHAN(n))
-@@ -641,12 +638,6 @@ static int bcm2835_dma_probe(struct plat
- goto err_no_dma;
- }
-
-- /*
-- * Do not use the FIQ and BULK channels,
-- * because they are used by the GPU.
-- */
-- chans_available &= ~(BCM2835_DMA_FIQ_MASK | BCM2835_DMA_BULK_MASK);
--
- for (i = 0; i < pdev->num_resources; i++) {
- irq = platform_get_irq(pdev, i);
- if (irq < 0)
diff --git a/target/linux/brcm2708/patches-4.4/0393-dmaengine-bcm2835-add-additional-defines-for-DMA-reg.patch b/target/linux/brcm2708/patches-4.4/0393-dmaengine-bcm2835-add-additional-defines-for-DMA-reg.patch
deleted file mode 100644
index 2527c0b..0000000
--- a/target/linux/brcm2708/patches-4.4/0393-dmaengine-bcm2835-add-additional-defines-for-DMA-reg.patch
+++ /dev/null
@@ -1,93 +0,0 @@
-From 1d7215d262e9a8190f8c8bef552d1186e2d3df9b Mon Sep 17 00:00:00 2001
-From: Martin Sperl <kernel at martin.sperl.org>
-Date: Wed, 16 Mar 2016 12:24:57 -0700
-Subject: [PATCH] dmaengine: bcm2835: add additional defines for DMA-registers
-
-Add additional defines describing the DMA registers
-as well as adding some more documentation to those registers.
-
-Signed-off-by: Martin Sperl <kernel at martin.sperl.org>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Vinod Koul <vinod.koul at intel.com>
----
- drivers/dma/bcm2835-dma.c | 57 ++++++++++++++++++++++++++++++++++++++++-------
- 1 file changed, 49 insertions(+), 8 deletions(-)
-
---- a/drivers/dma/bcm2835-dma.c
-+++ b/drivers/dma/bcm2835-dma.c
-@@ -97,26 +97,67 @@ struct bcm2835_desc {
-
- #define BCM2835_DMA_CS 0x00
- #define BCM2835_DMA_ADDR 0x04
-+#define BCM2835_DMA_TI 0x08
- #define BCM2835_DMA_SOURCE_AD 0x0c
- #define BCM2835_DMA_DEST_AD 0x10
--#define BCM2835_DMA_NEXTCB 0x1C
-+#define BCM2835_DMA_LEN 0x14
-+#define BCM2835_DMA_STRIDE 0x18
-+#define BCM2835_DMA_NEXTCB 0x1c
-+#define BCM2835_DMA_DEBUG 0x20
-
- /* DMA CS Control and Status bits */
--#define BCM2835_DMA_ACTIVE BIT(0)
--#define BCM2835_DMA_INT BIT(2)
-+#define BCM2835_DMA_ACTIVE BIT(0) /* activate the DMA */
-+#define BCM2835_DMA_END BIT(1) /* current CB has ended */
-+#define BCM2835_DMA_INT BIT(2) /* interrupt status */
-+#define BCM2835_DMA_DREQ BIT(3) /* DREQ state */
- #define BCM2835_DMA_ISPAUSED BIT(4) /* Pause requested or not active */
- #define BCM2835_DMA_ISHELD BIT(5) /* Is held by DREQ flow control */
--#define BCM2835_DMA_ERR BIT(8)
-+#define BCM2835_DMA_WAITING_FOR_WRITES BIT(6) /* waiting for last
-+ * AXI-write to ack
-+ */
-+#define BCM2835_DMA_ERR BIT(8)
-+#define BCM2835_DMA_PRIORITY(x) ((x & 15) << 16) /* AXI priority */
-+#define BCM2835_DMA_PANIC_PRIORITY(x) ((x & 15) << 20) /* panic priority */
-+/* current value of TI.BCM2835_DMA_WAIT_RESP */
-+#define BCM2835_DMA_WAIT_FOR_WRITES BIT(28)
-+#define BCM2835_DMA_DIS_DEBUG BIT(29) /* disable debug pause signal */
- #define BCM2835_DMA_ABORT BIT(30) /* Stop current CB, go to next, WO */
- #define BCM2835_DMA_RESET BIT(31) /* WO, self clearing */
-
-+/* Transfer information bits - also bcm2835_cb.info field */
- #define BCM2835_DMA_INT_EN BIT(0)
-+#define BCM2835_DMA_TDMODE BIT(1) /* 2D-Mode */
-+#define BCM2835_DMA_WAIT_RESP BIT(3) /* wait for AXI-write to be acked */
- #define BCM2835_DMA_D_INC BIT(4)
--#define BCM2835_DMA_D_DREQ BIT(6)
-+#define BCM2835_DMA_D_WIDTH BIT(5) /* 128bit writes if set */
-+#define BCM2835_DMA_D_DREQ BIT(6) /* enable DREQ for destination */
-+#define BCM2835_DMA_D_IGNORE BIT(7) /* ignore destination writes */
- #define BCM2835_DMA_S_INC BIT(8)
--#define BCM2835_DMA_S_DREQ BIT(10)
-+#define BCM2835_DMA_S_WIDTH BIT(9) /* 128bit writes if set */
-+#define BCM2835_DMA_S_DREQ BIT(10) /* enable SREQ for source */
-+#define BCM2835_DMA_S_IGNORE BIT(11) /* ignore source reads - read 0 */
-+#define BCM2835_DMA_BURST_LENGTH(x) ((x & 15) << 12)
-+#define BCM2835_DMA_PER_MAP(x) ((x & 31) << 16) /* REQ source */
-+#define BCM2835_DMA_WAIT(x) ((x & 31) << 21) /* add DMA-wait cycles */
-+#define BCM2835_DMA_NO_WIDE_BURSTS BIT(26) /* no 2 beat write bursts */
-
--#define BCM2835_DMA_PER_MAP(x) ((x) << 16)
-+/* debug register bits */
-+#define BCM2835_DMA_DEBUG_LAST_NOT_SET_ERR BIT(0)
-+#define BCM2835_DMA_DEBUG_FIFO_ERR BIT(1)
-+#define BCM2835_DMA_DEBUG_READ_ERR BIT(2)
-+#define BCM2835_DMA_DEBUG_OUTSTANDING_WRITES_SHIFT 4
-+#define BCM2835_DMA_DEBUG_OUTSTANDING_WRITES_BITS 4
-+#define BCM2835_DMA_DEBUG_ID_SHIFT 16
-+#define BCM2835_DMA_DEBUG_ID_BITS 9
-+#define BCM2835_DMA_DEBUG_STATE_SHIFT 16
-+#define BCM2835_DMA_DEBUG_STATE_BITS 9
-+#define BCM2835_DMA_DEBUG_VERSION_SHIFT 25
-+#define BCM2835_DMA_DEBUG_VERSION_BITS 3
-+#define BCM2835_DMA_DEBUG_LITE BIT(28)
-+
-+/* shared registers for all dma channels */
-+#define BCM2835_DMA_INT_STATUS 0xfe0
-+#define BCM2835_DMA_ENABLE 0xff0
-
- #define BCM2835_DMA_DATA_TYPE_S8 1
- #define BCM2835_DMA_DATA_TYPE_S16 2
diff --git a/target/linux/brcm2708/patches-4.4/0394-dmaengine-bcm2835-move-cyclic-member-from-bcm2835_ch.patch b/target/linux/brcm2708/patches-4.4/0394-dmaengine-bcm2835-move-cyclic-member-from-bcm2835_ch.patch
deleted file mode 100644
index 8a16780..0000000
--- a/target/linux/brcm2708/patches-4.4/0394-dmaengine-bcm2835-move-cyclic-member-from-bcm2835_ch.patch
+++ /dev/null
@@ -1,53 +0,0 @@
-From 621a48d74677ecf91fbaeebe8435e9ce6d1637f1 Mon Sep 17 00:00:00 2001
-From: Martin Sperl <kernel at martin.sperl.org>
-Date: Wed, 16 Mar 2016 12:24:58 -0700
-Subject: [PATCH] dmaengine: bcm2835: move cyclic member from bcm2835_chan into
- bcm2835_desc
-
-In preparation to consolidating code we move the cyclic member
-into the bcm_2835_desc structure.
-
-Signed-off-by: Martin Sperl <kernel at martin.sperl.org>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Vinod Koul <vinod.koul at intel.com>
----
- drivers/dma/bcm2835-dma.c | 6 +++---
- 1 file changed, 3 insertions(+), 3 deletions(-)
-
---- a/drivers/dma/bcm2835-dma.c
-+++ b/drivers/dma/bcm2835-dma.c
-@@ -73,7 +73,6 @@ struct bcm2835_chan {
- struct list_head node;
-
- struct dma_slave_config cfg;
-- bool cyclic;
- unsigned int dreq;
-
- int ch;
-@@ -93,6 +92,8 @@ struct bcm2835_desc {
-
- unsigned int frames;
- size_t size;
-+
-+ bool cyclic;
- };
-
- #define BCM2835_DMA_CS 0x00
-@@ -377,8 +378,6 @@ static void bcm2835_dma_issue_pending(st
- struct bcm2835_chan *c = to_bcm2835_dma_chan(chan);
- unsigned long flags;
-
-- c->cyclic = true; /* Nothing else is implemented */
--
- spin_lock_irqsave(&c->vc.lock, flags);
- if (vchan_issue_pending(&c->vc) && !c->desc)
- bcm2835_dma_start_desc(c);
-@@ -432,6 +431,7 @@ static struct dma_async_tx_descriptor *b
- d->c = c;
- d->dir = direction;
- d->frames = buf_len / period_len;
-+ d->cyclic = true;
-
- d->cb_list = kcalloc(d->frames, sizeof(*d->cb_list), GFP_KERNEL);
- if (!d->cb_list) {
diff --git a/target/linux/brcm2708/patches-4.4/0395-dmaengine-bcm2835-move-controlblock-chain-generation.patch b/target/linux/brcm2708/patches-4.4/0395-dmaengine-bcm2835-move-controlblock-chain-generation.patch
deleted file mode 100644
index d942338..0000000
--- a/target/linux/brcm2708/patches-4.4/0395-dmaengine-bcm2835-move-controlblock-chain-generation.patch
+++ /dev/null
@@ -1,378 +0,0 @@
-From 3710f8c9b410aad29ef4b37be90c6290e16bf6cb Mon Sep 17 00:00:00 2001
-From: Martin Sperl <kernel at martin.sperl.org>
-Date: Wed, 16 Mar 2016 12:24:59 -0700
-Subject: [PATCH] dmaengine: bcm2835: move controlblock chain generation into
- separate method
-
-In preparation of adding slave_sg functionality this patch moves the
-generation/allocation of bcm2835_desc and the building of
-the corresponding DMA-control-block chain from bcm2835_dma_prep_dma_cyclic
-into the newly created method bcm2835_dma_create_cb_chain.
-
-Signed-off-by: Martin Sperl <kernel at martin.sperl.org>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Vinod Koul <vinod.koul at intel.com>
----
- drivers/dma/bcm2835-dma.c | 294 +++++++++++++++++++++++++++++++---------------
- 1 file changed, 198 insertions(+), 96 deletions(-)
-
---- a/drivers/dma/bcm2835-dma.c
-+++ b/drivers/dma/bcm2835-dma.c
-@@ -88,12 +88,12 @@ struct bcm2835_desc {
- struct virt_dma_desc vd;
- enum dma_transfer_direction dir;
-
-- struct bcm2835_cb_entry *cb_list;
--
- unsigned int frames;
- size_t size;
-
- bool cyclic;
-+
-+ struct bcm2835_cb_entry cb_list[];
- };
-
- #define BCM2835_DMA_CS 0x00
-@@ -169,6 +169,13 @@ struct bcm2835_desc {
- #define BCM2835_DMA_CHAN(n) ((n) << 8) /* Base address */
- #define BCM2835_DMA_CHANIO(base, n) ((base) + BCM2835_DMA_CHAN(n))
-
-+/* how many frames of max_len size do we need to transfer len bytes */
-+static inline size_t bcm2835_dma_frames_for_length(size_t len,
-+ size_t max_len)
-+{
-+ return DIV_ROUND_UP(len, max_len);
-+}
-+
- static inline struct bcm2835_dmadev *to_bcm2835_dma_dev(struct dma_device *d)
- {
- return container_of(d, struct bcm2835_dmadev, ddev);
-@@ -185,19 +192,161 @@ static inline struct bcm2835_desc *to_bc
- return container_of(t, struct bcm2835_desc, vd.tx);
- }
-
--static void bcm2835_dma_desc_free(struct virt_dma_desc *vd)
-+static void bcm2835_dma_free_cb_chain(struct bcm2835_desc *desc)
- {
-- struct bcm2835_desc *desc = container_of(vd, struct bcm2835_desc, vd);
-- int i;
-+ size_t i;
-
- for (i = 0; i < desc->frames; i++)
- dma_pool_free(desc->c->cb_pool, desc->cb_list[i].cb,
- desc->cb_list[i].paddr);
-
-- kfree(desc->cb_list);
- kfree(desc);
- }
-
-+static void bcm2835_dma_desc_free(struct virt_dma_desc *vd)
-+{
-+ bcm2835_dma_free_cb_chain(
-+ container_of(vd, struct bcm2835_desc, vd));
-+}
-+
-+static void bcm2835_dma_create_cb_set_length(
-+ struct bcm2835_chan *chan,
-+ struct bcm2835_dma_cb *control_block,
-+ size_t len,
-+ size_t period_len,
-+ size_t *total_len,
-+ u32 finalextrainfo)
-+{
-+ /* set the length */
-+ control_block->length = len;
-+
-+ /* finished if we have no period_length */
-+ if (!period_len)
-+ return;
-+
-+ /*
-+ * period_len means: that we need to generate
-+ * transfers that are terminating at every
-+ * multiple of period_len - this is typically
-+ * used to set the interrupt flag in info
-+ * which is required during cyclic transfers
-+ */
-+
-+ /* have we filled in period_length yet? */
-+ if (*total_len + control_block->length < period_len)
-+ return;
-+
-+ /* calculate the length that remains to reach period_length */
-+ control_block->length = period_len - *total_len;
-+
-+ /* reset total_length for next period */
-+ *total_len = 0;
-+
-+ /* add extrainfo bits in info */
-+ control_block->info |= finalextrainfo;
-+}
-+
-+/**
-+ * bcm2835_dma_create_cb_chain - create a control block and fills data in
-+ *
-+ * @chan: the @dma_chan for which we run this
-+ * @direction: the direction in which we transfer
-+ * @cyclic: it is a cyclic transfer
-+ * @info: the default info bits to apply per controlblock
-+ * @frames: number of controlblocks to allocate
-+ * @src: the src address to assign (if the S_INC bit is set
-+ * in @info, then it gets incremented)
-+ * @dst: the dst address to assign (if the D_INC bit is set
-+ * in @info, then it gets incremented)
-+ * @buf_len: the full buffer length (may also be 0)
-+ * @period_len: the period length when to apply @finalextrainfo
-+ * in addition to the last transfer
-+ * this will also break some control-blocks early
-+ * @finalextrainfo: additional bits in last controlblock
-+ * (or when period_len is reached in case of cyclic)
-+ * @gfp: the GFP flag to use for allocation
-+ */
-+static struct bcm2835_desc *bcm2835_dma_create_cb_chain(
-+ struct dma_chan *chan, enum dma_transfer_direction direction,
-+ bool cyclic, u32 info, u32 finalextrainfo, size_t frames,
-+ dma_addr_t src, dma_addr_t dst, size_t buf_len,
-+ size_t period_len, gfp_t gfp)
-+{
-+ struct bcm2835_chan *c = to_bcm2835_dma_chan(chan);
-+ size_t len = buf_len, total_len;
-+ size_t frame;
-+ struct bcm2835_desc *d;
-+ struct bcm2835_cb_entry *cb_entry;
-+ struct bcm2835_dma_cb *control_block;
-+
-+ /* allocate and setup the descriptor. */
-+ d = kzalloc(sizeof(*d) + frames * sizeof(struct bcm2835_cb_entry),
-+ gfp);
-+ if (!d)
-+ return NULL;
-+
-+ d->c = c;
-+ d->dir = direction;
-+ d->cyclic = cyclic;
-+
-+ /*
-+ * Iterate over all frames, create a control block
-+ * for each frame and link them together.
-+ */
-+ for (frame = 0, total_len = 0; frame < frames; d->frames++, frame++) {
-+ cb_entry = &d->cb_list[frame];
-+ cb_entry->cb = dma_pool_alloc(c->cb_pool, gfp,
-+ &cb_entry->paddr);
-+ if (!cb_entry->cb)
-+ goto error_cb;
-+
-+ /* fill in the control block */
-+ control_block = cb_entry->cb;
-+ control_block->info = info;
-+ control_block->src = src;
-+ control_block->dst = dst;
-+ control_block->stride = 0;
-+ control_block->next = 0;
-+ /* set up length in control_block if requested */
-+ if (buf_len) {
-+ /* calculate length honoring period_length */
-+ bcm2835_dma_create_cb_set_length(
-+ c, control_block,
-+ len, period_len, &total_len,
-+ cyclic ? finalextrainfo : 0);
-+
-+ /* calculate new remaining length */
-+ len -= control_block->length;
-+ }
-+
-+ /* link this the last controlblock */
-+ if (frame)
-+ d->cb_list[frame - 1].cb->next = cb_entry->paddr;
-+
-+ /* update src and dst and length */
-+ if (src && (info & BCM2835_DMA_S_INC))
-+ src += control_block->length;
-+ if (dst && (info & BCM2835_DMA_D_INC))
-+ dst += control_block->length;
-+
-+ /* Length of total transfer */
-+ d->size += control_block->length;
-+ }
-+
-+ /* the last frame requires extra flags */
-+ d->cb_list[d->frames - 1].cb->info |= finalextrainfo;
-+
-+ /* detect a size missmatch */
-+ if (buf_len && (d->size != buf_len))
-+ goto error_cb;
-+
-+ return d;
-+error_cb:
-+ bcm2835_dma_free_cb_chain(d);
-+
-+ return NULL;
-+}
-+
- static int bcm2835_dma_abort(void __iomem *chan_base)
- {
- unsigned long cs;
-@@ -391,12 +540,11 @@ static struct dma_async_tx_descriptor *b
- unsigned long flags)
- {
- struct bcm2835_chan *c = to_bcm2835_dma_chan(chan);
-- enum dma_slave_buswidth dev_width;
- struct bcm2835_desc *d;
-- dma_addr_t dev_addr;
-- unsigned int es, sync_type;
-- unsigned int frame;
-- int i;
-+ dma_addr_t src, dst;
-+ u32 info = BCM2835_DMA_WAIT_RESP;
-+ u32 extra = BCM2835_DMA_INT_EN;
-+ size_t frames;
-
- /* Grab configuration */
- if (!is_slave_direction(direction)) {
-@@ -404,104 +552,58 @@ static struct dma_async_tx_descriptor *b
- return NULL;
- }
-
-- if (direction == DMA_DEV_TO_MEM) {
-- dev_addr = c->cfg.src_addr;
-- dev_width = c->cfg.src_addr_width;
-- sync_type = BCM2835_DMA_S_DREQ;
-- } else {
-- dev_addr = c->cfg.dst_addr;
-- dev_width = c->cfg.dst_addr_width;
-- sync_type = BCM2835_DMA_D_DREQ;
-- }
--
-- /* Bus width translates to the element size (ES) */
-- switch (dev_width) {
-- case DMA_SLAVE_BUSWIDTH_4_BYTES:
-- es = BCM2835_DMA_DATA_TYPE_S32;
-- break;
-- default:
-+ if (!buf_len) {
-+ dev_err(chan->device->dev,
-+ "%s: bad buffer length (= 0)\n", __func__);
- return NULL;
- }
-
-- /* Now allocate and setup the descriptor. */
-- d = kzalloc(sizeof(*d), GFP_NOWAIT);
-- if (!d)
-- return NULL;
--
-- d->c = c;
-- d->dir = direction;
-- d->frames = buf_len / period_len;
-- d->cyclic = true;
-+ /*
-+ * warn if buf_len is not a multiple of period_len - this may leed
-+ * to unexpected latencies for interrupts and thus audiable clicks
-+ */
-+ if (buf_len % period_len)
-+ dev_warn_once(chan->device->dev,
-+ "%s: buffer_length (%zd) is not a multiple of period_len (%zd)\n",
-+ __func__, buf_len, period_len);
-+
-+ /* Setup DREQ channel */
-+ if (c->dreq != 0)
-+ info |= BCM2835_DMA_PER_MAP(c->dreq);
-
-- d->cb_list = kcalloc(d->frames, sizeof(*d->cb_list), GFP_KERNEL);
-- if (!d->cb_list) {
-- kfree(d);
-- return NULL;
-+ if (direction == DMA_DEV_TO_MEM) {
-+ if (c->cfg.src_addr_width != DMA_SLAVE_BUSWIDTH_4_BYTES)
-+ return NULL;
-+ src = c->cfg.src_addr;
-+ dst = buf_addr;
-+ info |= BCM2835_DMA_S_DREQ | BCM2835_DMA_D_INC;
-+ } else {
-+ if (c->cfg.dst_addr_width != DMA_SLAVE_BUSWIDTH_4_BYTES)
-+ return NULL;
-+ dst = c->cfg.dst_addr;
-+ src = buf_addr;
-+ info |= BCM2835_DMA_D_DREQ | BCM2835_DMA_S_INC;
- }
-- /* Allocate memory for control blocks */
-- for (i = 0; i < d->frames; i++) {
-- struct bcm2835_cb_entry *cb_entry = &d->cb_list[i];
-
-- cb_entry->cb = dma_pool_zalloc(c->cb_pool, GFP_ATOMIC,
-- &cb_entry->paddr);
-- if (!cb_entry->cb)
-- goto error_cb;
-- }
-+ /* calculate number of frames */
-+ frames = DIV_ROUND_UP(buf_len, period_len);
-
- /*
-- * Iterate over all frames, create a control block
-- * for each frame and link them together.
-+ * allocate the CB chain
-+ * note that we need to use GFP_NOWAIT, as the ALSA i2s dmaengine
-+ * implementation calls prep_dma_cyclic with interrupts disabled.
- */
-- for (frame = 0; frame < d->frames; frame++) {
-- struct bcm2835_dma_cb *control_block = d->cb_list[frame].cb;
--
-- /* Setup adresses */
-- if (d->dir == DMA_DEV_TO_MEM) {
-- control_block->info = BCM2835_DMA_D_INC;
-- control_block->src = dev_addr;
-- control_block->dst = buf_addr + frame * period_len;
-- } else {
-- control_block->info = BCM2835_DMA_S_INC;
-- control_block->src = buf_addr + frame * period_len;
-- control_block->dst = dev_addr;
-- }
--
-- /* Enable interrupt */
-- control_block->info |= BCM2835_DMA_INT_EN;
--
-- /* Setup synchronization */
-- if (sync_type != 0)
-- control_block->info |= sync_type;
--
-- /* Setup DREQ channel */
-- if (c->dreq != 0)
-- control_block->info |=
-- BCM2835_DMA_PER_MAP(c->dreq);
--
-- /* Length of a frame */
-- control_block->length = period_len;
-- d->size += control_block->length;
-+ d = bcm2835_dma_create_cb_chain(chan, direction, true,
-+ info, extra,
-+ frames, src, dst, buf_len,
-+ period_len, GFP_NOWAIT);
-+ if (!d)
-+ return NULL;
-
-- /*
-- * Next block is the next frame.
-- * This DMA engine driver currently only supports cyclic DMA.
-- * Therefore, wrap around at number of frames.
-- */
-- control_block->next = d->cb_list[((frame + 1) % d->frames)].paddr;
-- }
-+ /* wrap around into a loop */
-+ d->cb_list[d->frames - 1].cb->next = d->cb_list[0].paddr;
-
- return vchan_tx_prep(&c->vc, &d->vd, flags);
--error_cb:
-- i--;
-- for (; i >= 0; i--) {
-- struct bcm2835_cb_entry *cb_entry = &d->cb_list[i];
--
-- dma_pool_free(c->cb_pool, cb_entry->cb, cb_entry->paddr);
-- }
--
-- kfree(d->cb_list);
-- kfree(d);
-- return NULL;
- }
-
- static int bcm2835_dma_slave_config(struct dma_chan *chan,
diff --git a/target/linux/brcm2708/patches-4.4/0396-dmaengine-bcm2835-limit-max-length-based-on-channel-.patch b/target/linux/brcm2708/patches-4.4/0396-dmaengine-bcm2835-limit-max-length-based-on-channel-.patch
deleted file mode 100644
index 20fb886..0000000
--- a/target/linux/brcm2708/patches-4.4/0396-dmaengine-bcm2835-limit-max-length-based-on-channel-.patch
+++ /dev/null
@@ -1,114 +0,0 @@
-From 426f54e1e932f40b666b238ef37d0610fd35d0d0 Mon Sep 17 00:00:00 2001
-From: Martin Sperl <kernel at martin.sperl.org>
-Date: Wed, 16 Mar 2016 12:25:00 -0700
-Subject: [PATCH] dmaengine: bcm2835: limit max length based on channel type
-
-The bcm2835 dma system has 2 basic types of dma-channels:
-* "normal" channels
-* "light" channels
-
-Lite channels are limited in several aspects:
-* internal data-structure is 128 bit (not 256)
-* does not support BCM2835_DMA_TDMODE (2D)
-* DMA length register is limited to 16 bit.
- so 0-65535 (not 0-65536 as mentioned in the official datasheet)
-* BCM2835_DMA_S/D_IGNORE are not supported
-
-The detection of the type of mode is implemented by looking at
-the LITE bit in the DEBUG register for each channel.
-This allows automatic detection.
-
-Based on this the maximum block size is set to (64K - 4) or to 1G
-and this limit is honored during generation of control block
-chains. The effect is that when a LITE channel is used more
-control blocks are used to do the same transfer (compared
-to a normal channel).
-
-As there are several sources/target DREQS that are 32 bit wide
-we need to have the transfer to be a multiple of 4 as this would
-break the transfer otherwise.
-
-This is why the limit of (64K - 4) was chosen over the
-alternative of (64K - 4K).
-
-Signed-off-by: Martin Sperl <kernel at martin.sperl.org>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Vinod Koul <vinod.koul at intel.com>
----
- drivers/dma/bcm2835-dma.c | 29 ++++++++++++++++++++++++++---
- 1 file changed, 26 insertions(+), 3 deletions(-)
-
---- a/drivers/dma/bcm2835-dma.c
-+++ b/drivers/dma/bcm2835-dma.c
-@@ -81,6 +81,8 @@ struct bcm2835_chan {
-
- void __iomem *chan_base;
- int irq_number;
-+
-+ bool is_lite_channel;
- };
-
- struct bcm2835_desc {
-@@ -169,6 +171,16 @@ struct bcm2835_desc {
- #define BCM2835_DMA_CHAN(n) ((n) << 8) /* Base address */
- #define BCM2835_DMA_CHANIO(base, n) ((base) + BCM2835_DMA_CHAN(n))
-
-+/* the max dma length for different channels */
-+#define MAX_DMA_LEN SZ_1G
-+#define MAX_LITE_DMA_LEN (SZ_64K - 4)
-+
-+static inline size_t bcm2835_dma_max_frame_length(struct bcm2835_chan *c)
-+{
-+ /* lite and normal channels have different max frame length */
-+ return c->is_lite_channel ? MAX_LITE_DMA_LEN : MAX_DMA_LEN;
-+}
-+
- /* how many frames of max_len size do we need to transfer len bytes */
- static inline size_t bcm2835_dma_frames_for_length(size_t len,
- size_t max_len)
-@@ -217,8 +229,10 @@ static void bcm2835_dma_create_cb_set_le
- size_t *total_len,
- u32 finalextrainfo)
- {
-- /* set the length */
-- control_block->length = len;
-+ size_t max_len = bcm2835_dma_max_frame_length(chan);
-+
-+ /* set the length taking lite-channel limitations into account */
-+ control_block->length = min_t(u32, len, max_len);
-
- /* finished if we have no period_length */
- if (!period_len)
-@@ -544,6 +558,7 @@ static struct dma_async_tx_descriptor *b
- dma_addr_t src, dst;
- u32 info = BCM2835_DMA_WAIT_RESP;
- u32 extra = BCM2835_DMA_INT_EN;
-+ size_t max_len = bcm2835_dma_max_frame_length(c);
- size_t frames;
-
- /* Grab configuration */
-@@ -586,7 +601,10 @@ static struct dma_async_tx_descriptor *b
- }
-
- /* calculate number of frames */
-- frames = DIV_ROUND_UP(buf_len, period_len);
-+ frames = /* number of periods */
-+ DIV_ROUND_UP(buf_len, period_len) *
-+ /* number of frames per period */
-+ bcm2835_dma_frames_for_length(period_len, max_len);
-
- /*
- * allocate the CB chain
-@@ -685,6 +703,11 @@ static int bcm2835_dma_chan_init(struct
- c->ch = chan_id;
- c->irq_number = irq;
-
-+ /* check in DEBUG register if this is a LITE channel */
-+ if (readl(c->chan_base + BCM2835_DMA_DEBUG) &
-+ BCM2835_DMA_DEBUG_LITE)
-+ c->is_lite_channel = true;
-+
- return 0;
- }
-
diff --git a/target/linux/brcm2708/patches-4.4/0397-dmaengine-bcm2835-add-slave_sg-support-to-bcm2835-dm.patch b/target/linux/brcm2708/patches-4.4/0397-dmaengine-bcm2835-add-slave_sg-support-to-bcm2835-dm.patch
deleted file mode 100644
index 776871d..0000000
--- a/target/linux/brcm2708/patches-4.4/0397-dmaengine-bcm2835-add-slave_sg-support-to-bcm2835-dm.patch
+++ /dev/null
@@ -1,182 +0,0 @@
-From dcfe16f80447e411dbe91144592f33f452fb6067 Mon Sep 17 00:00:00 2001
-From: Martin Sperl <kernel at martin.sperl.org>
-Date: Wed, 16 Mar 2016 12:25:01 -0700
-Subject: [PATCH] dmaengine: bcm2835: add slave_sg support to bcm2835-dma
-
-Add slave_sg support to bcm2835-dma using shared allocation
-code for bcm2835_desc and DMA-control blocks already used by
-dma_cyclic.
-
-Note that bcm2835_dma_callback had to get modified to support
-both modes of operation (cyclic and non-cyclic).
-
-Tested using:
-* Hifiberry I2S card (using cyclic DMA)
-* fb_st7735r SPI-framebuffer (using slave_sg DMA via spi-bcm2835)
-playing BigBuckBunny for audio and video.
-
-Signed-off-by: Martin Sperl <kernel at martin.sperl.org>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Vinod Koul <vinod.koul at intel.com>
----
- drivers/dma/bcm2835-dma.c | 113 ++++++++++++++++++++++++++++++++++++++++++++--
- 1 file changed, 108 insertions(+), 5 deletions(-)
-
---- a/drivers/dma/bcm2835-dma.c
-+++ b/drivers/dma/bcm2835-dma.c
-@@ -260,6 +260,23 @@ static void bcm2835_dma_create_cb_set_le
- control_block->info |= finalextrainfo;
- }
-
-+static inline size_t bcm2835_dma_count_frames_for_sg(
-+ struct bcm2835_chan *c,
-+ struct scatterlist *sgl,
-+ unsigned int sg_len)
-+{
-+ size_t frames = 0;
-+ struct scatterlist *sgent;
-+ unsigned int i;
-+ size_t plength = bcm2835_dma_max_frame_length(c);
-+
-+ for_each_sg(sgl, sgent, sg_len, i)
-+ frames += bcm2835_dma_frames_for_length(
-+ sg_dma_len(sgent), plength);
-+
-+ return frames;
-+}
-+
- /**
- * bcm2835_dma_create_cb_chain - create a control block and fills data in
- *
-@@ -361,6 +378,32 @@ error_cb:
- return NULL;
- }
-
-+static void bcm2835_dma_fill_cb_chain_with_sg(
-+ struct dma_chan *chan,
-+ enum dma_transfer_direction direction,
-+ struct bcm2835_cb_entry *cb,
-+ struct scatterlist *sgl,
-+ unsigned int sg_len)
-+{
-+ struct bcm2835_chan *c = to_bcm2835_dma_chan(chan);
-+ size_t max_len = bcm2835_dma_max_frame_length(c);
-+ unsigned int i, len;
-+ dma_addr_t addr;
-+ struct scatterlist *sgent;
-+
-+ for_each_sg(sgl, sgent, sg_len, i) {
-+ for (addr = sg_dma_address(sgent), len = sg_dma_len(sgent);
-+ len > 0;
-+ addr += cb->cb->length, len -= cb->cb->length, cb++) {
-+ if (direction == DMA_DEV_TO_MEM)
-+ cb->cb->dst = addr;
-+ else
-+ cb->cb->src = addr;
-+ cb->cb->length = min(len, max_len);
-+ }
-+ }
-+}
-+
- static int bcm2835_dma_abort(void __iomem *chan_base)
- {
- unsigned long cs;
-@@ -428,13 +471,19 @@ static irqreturn_t bcm2835_dma_callback(
- d = c->desc;
-
- if (d) {
-- /* TODO Only works for cyclic DMA */
-- vchan_cyclic_callback(&d->vd);
-+ if (d->cyclic) {
-+ /* call the cyclic callback */
-+ vchan_cyclic_callback(&d->vd);
-+
-+ /* Keep the DMA engine running */
-+ writel(BCM2835_DMA_ACTIVE,
-+ c->chan_base + BCM2835_DMA_CS);
-+ } else {
-+ vchan_cookie_complete(&c->desc->vd);
-+ bcm2835_dma_start_desc(c);
-+ }
- }
-
-- /* Keep the DMA engine running */
-- writel(BCM2835_DMA_ACTIVE, c->chan_base + BCM2835_DMA_CS);
--
- spin_unlock_irqrestore(&c->vc.lock, flags);
-
- return IRQ_HANDLED;
-@@ -548,6 +597,58 @@ static void bcm2835_dma_issue_pending(st
- spin_unlock_irqrestore(&c->vc.lock, flags);
- }
-
-+static struct dma_async_tx_descriptor *bcm2835_dma_prep_slave_sg(
-+ struct dma_chan *chan,
-+ struct scatterlist *sgl, unsigned int sg_len,
-+ enum dma_transfer_direction direction,
-+ unsigned long flags, void *context)
-+{
-+ struct bcm2835_chan *c = to_bcm2835_dma_chan(chan);
-+ struct bcm2835_desc *d;
-+ dma_addr_t src = 0, dst = 0;
-+ u32 info = BCM2835_DMA_WAIT_RESP;
-+ u32 extra = BCM2835_DMA_INT_EN;
-+ size_t frames;
-+
-+ if (!is_slave_direction(direction)) {
-+ dev_err(chan->device->dev,
-+ "%s: bad direction?\n", __func__);
-+ return NULL;
-+ }
-+
-+ if (c->dreq != 0)
-+ info |= BCM2835_DMA_PER_MAP(c->dreq);
-+
-+ if (direction == DMA_DEV_TO_MEM) {
-+ if (c->cfg.src_addr_width != DMA_SLAVE_BUSWIDTH_4_BYTES)
-+ return NULL;
-+ src = c->cfg.src_addr;
-+ info |= BCM2835_DMA_S_DREQ | BCM2835_DMA_D_INC;
-+ } else {
-+ if (c->cfg.dst_addr_width != DMA_SLAVE_BUSWIDTH_4_BYTES)
-+ return NULL;
-+ dst = c->cfg.dst_addr;
-+ info |= BCM2835_DMA_D_DREQ | BCM2835_DMA_S_INC;
-+ }
-+
-+ /* count frames in sg list */
-+ frames = bcm2835_dma_count_frames_for_sg(c, sgl, sg_len);
-+
-+ /* allocate the CB chain */
-+ d = bcm2835_dma_create_cb_chain(chan, direction, false,
-+ info, extra,
-+ frames, src, dst, 0, 0,
-+ GFP_KERNEL);
-+ if (!d)
-+ return NULL;
-+
-+ /* fill in frames with scatterlist pointers */
-+ bcm2835_dma_fill_cb_chain_with_sg(chan, direction, d->cb_list,
-+ sgl, sg_len);
-+
-+ return vchan_tx_prep(&c->vc, &d->vd, flags);
-+}
-+
- static struct dma_async_tx_descriptor *bcm2835_dma_prep_dma_cyclic(
- struct dma_chan *chan, dma_addr_t buf_addr, size_t buf_len,
- size_t period_len, enum dma_transfer_direction direction,
-@@ -778,11 +879,13 @@ static int bcm2835_dma_probe(struct plat
- dma_cap_set(DMA_SLAVE, od->ddev.cap_mask);
- dma_cap_set(DMA_PRIVATE, od->ddev.cap_mask);
- dma_cap_set(DMA_CYCLIC, od->ddev.cap_mask);
-+ dma_cap_set(DMA_SLAVE, od->ddev.cap_mask);
- od->ddev.device_alloc_chan_resources = bcm2835_dma_alloc_chan_resources;
- od->ddev.device_free_chan_resources = bcm2835_dma_free_chan_resources;
- od->ddev.device_tx_status = bcm2835_dma_tx_status;
- od->ddev.device_issue_pending = bcm2835_dma_issue_pending;
- od->ddev.device_prep_dma_cyclic = bcm2835_dma_prep_dma_cyclic;
-+ od->ddev.device_prep_slave_sg = bcm2835_dma_prep_slave_sg;
- od->ddev.device_config = bcm2835_dma_slave_config;
- od->ddev.device_terminate_all = bcm2835_dma_terminate_all;
- od->ddev.src_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_4_BYTES);
diff --git a/target/linux/brcm2708/patches-4.4/0398-dmaengine-bcm2835-add-dma_memcopy-support-to-bcm2835.patch b/target/linux/brcm2708/patches-4.4/0398-dmaengine-bcm2835-add-dma_memcopy-support-to-bcm2835.patch
deleted file mode 100644
index 5d063a9..0000000
--- a/target/linux/brcm2708/patches-4.4/0398-dmaengine-bcm2835-add-dma_memcopy-support-to-bcm2835.patch
+++ /dev/null
@@ -1,87 +0,0 @@
-From 5e439596e0a4a5a14556d8b3f246e7204a8f3cd0 Mon Sep 17 00:00:00 2001
-From: Martin Sperl <kernel at martin.sperl.org>
-Date: Wed, 16 Mar 2016 12:25:02 -0700
-Subject: [PATCH] dmaengine: bcm2835: add dma_memcopy support to bcm2835-dma
-
-Also added check for an error condition in bcm2835_dma_create_cb_chain
-that showed up during development of this patch.
-
-Tested using dmatest for all enabled channels.
-
-Signed-off-by: Martin Sperl <kernel at martin.sperl.org>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Vinod Koul <vinod.koul at intel.com>
----
- drivers/dma/bcm2835-dma.c | 36 +++++++++++++++++++++++++++++++++++-
- 1 file changed, 35 insertions(+), 1 deletion(-)
-
---- a/drivers/dma/bcm2835-dma.c
-+++ b/drivers/dma/bcm2835-dma.c
-@@ -310,6 +310,9 @@ static struct bcm2835_desc *bcm2835_dma_
- struct bcm2835_cb_entry *cb_entry;
- struct bcm2835_dma_cb *control_block;
-
-+ if (!frames)
-+ return NULL;
-+
- /* allocate and setup the descriptor. */
- d = kzalloc(sizeof(*d) + frames * sizeof(struct bcm2835_cb_entry),
- gfp);
-@@ -597,6 +600,34 @@ static void bcm2835_dma_issue_pending(st
- spin_unlock_irqrestore(&c->vc.lock, flags);
- }
-
-+struct dma_async_tx_descriptor *bcm2835_dma_prep_dma_memcpy(
-+ struct dma_chan *chan, dma_addr_t dst, dma_addr_t src,
-+ size_t len, unsigned long flags)
-+{
-+ struct bcm2835_chan *c = to_bcm2835_dma_chan(chan);
-+ struct bcm2835_desc *d;
-+ u32 info = BCM2835_DMA_D_INC | BCM2835_DMA_S_INC;
-+ u32 extra = BCM2835_DMA_INT_EN | BCM2835_DMA_WAIT_RESP;
-+ size_t max_len = bcm2835_dma_max_frame_length(c);
-+ size_t frames;
-+
-+ /* if src, dst or len is not given return with an error */
-+ if (!src || !dst || !len)
-+ return NULL;
-+
-+ /* calculate number of frames */
-+ frames = bcm2835_dma_frames_for_length(len, max_len);
-+
-+ /* allocate the CB chain - this also fills in the pointers */
-+ d = bcm2835_dma_create_cb_chain(chan, DMA_MEM_TO_MEM, false,
-+ info, extra, frames,
-+ src, dst, len, 0, GFP_KERNEL);
-+ if (!d)
-+ return NULL;
-+
-+ return vchan_tx_prep(&c->vc, &d->vd, flags);
-+}
-+
- static struct dma_async_tx_descriptor *bcm2835_dma_prep_slave_sg(
- struct dma_chan *chan,
- struct scatterlist *sgl, unsigned int sg_len,
-@@ -880,17 +911,20 @@ static int bcm2835_dma_probe(struct plat
- dma_cap_set(DMA_PRIVATE, od->ddev.cap_mask);
- dma_cap_set(DMA_CYCLIC, od->ddev.cap_mask);
- dma_cap_set(DMA_SLAVE, od->ddev.cap_mask);
-+ dma_cap_set(DMA_MEMCPY, od->ddev.cap_mask);
- od->ddev.device_alloc_chan_resources = bcm2835_dma_alloc_chan_resources;
- od->ddev.device_free_chan_resources = bcm2835_dma_free_chan_resources;
- od->ddev.device_tx_status = bcm2835_dma_tx_status;
- od->ddev.device_issue_pending = bcm2835_dma_issue_pending;
- od->ddev.device_prep_dma_cyclic = bcm2835_dma_prep_dma_cyclic;
- od->ddev.device_prep_slave_sg = bcm2835_dma_prep_slave_sg;
-+ od->ddev.device_prep_dma_memcpy = bcm2835_dma_prep_dma_memcpy;
- od->ddev.device_config = bcm2835_dma_slave_config;
- od->ddev.device_terminate_all = bcm2835_dma_terminate_all;
- od->ddev.src_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_4_BYTES);
- od->ddev.dst_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_4_BYTES);
-- od->ddev.directions = BIT(DMA_DEV_TO_MEM) | BIT(DMA_MEM_TO_DEV);
-+ od->ddev.directions = BIT(DMA_DEV_TO_MEM) | BIT(DMA_MEM_TO_DEV) |
-+ BIT(DMA_MEM_TO_MEM);
- od->ddev.residue_granularity = DMA_RESIDUE_GRANULARITY_BURST;
- od->ddev.dev = &pdev->dev;
- INIT_LIST_HEAD(&od->ddev.channels);
diff --git a/target/linux/brcm2708/patches-4.4/0399-dmaengine-bcm2835-use-platform_get_irq_byname.patch b/target/linux/brcm2708/patches-4.4/0399-dmaengine-bcm2835-use-platform_get_irq_byname.patch
deleted file mode 100644
index 1252039..0000000
--- a/target/linux/brcm2708/patches-4.4/0399-dmaengine-bcm2835-use-platform_get_irq_byname.patch
+++ /dev/null
@@ -1,170 +0,0 @@
-From c2de1d10f8c29605bafc57d541f9b904b05c81b5 Mon Sep 17 00:00:00 2001
-From: Martin Sperl <kernel at martin.sperl.org>
-Date: Mon, 11 Apr 2016 13:29:08 +0000
-Subject: [PATCH] dmaengine: bcm2835: use platform_get_irq_byname
-
-Use platform_get_irq_byname to allow for correct mapping of
-interrupts to dma channels.
-
-The currently implemented device tree is unfortunately
-implemented with the wrong assumption, that each dma-channel
-has its own dma channel, but dma-irq 11 is handling
-dma-channel 11-14 and dma-irq 12 is actually a "catch all"
-interrupt.
-
-So here we use the byname variant and require that interrupts
-are explicitly named via the interrupts-name property in the
-device tree.
-
-The use of shared interrupts is also implemented.
-
-As a side-effect this means we can now use dma channels 12, 13 and 14
-in a correct manner - also testing shows that onl using
-channels 11 to 14 for spi and i2s works perfectly (when playing
-some video)
-
-Signed-off-by: Martin Sperl <kernel at martin.sperl.org>
-Acked-by: Eric Anholt <eric at anholt.net>
-Acked-by: Mark Rutland <mark.rutland at arm.com>
-Signed-off-by: Vinod Koul <vinod.koul at intel.com>
----
- drivers/dma/bcm2835-dma.c | 77 ++++++++++++++++++++++++++++++++++++++---------
- 1 file changed, 63 insertions(+), 14 deletions(-)
-
---- a/drivers/dma/bcm2835-dma.c
-+++ b/drivers/dma/bcm2835-dma.c
-@@ -46,6 +46,9 @@
-
- #include "virt-dma.h"
-
-+#define BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED 14
-+#define BCM2835_DMA_CHAN_NAME_SIZE 8
-+
- struct bcm2835_dmadev {
- struct dma_device ddev;
- spinlock_t lock;
-@@ -81,6 +84,7 @@ struct bcm2835_chan {
-
- void __iomem *chan_base;
- int irq_number;
-+ unsigned int irq_flags;
-
- bool is_lite_channel;
- };
-@@ -466,6 +470,15 @@ static irqreturn_t bcm2835_dma_callback(
- struct bcm2835_desc *d;
- unsigned long flags;
-
-+ /* check the shared interrupt */
-+ if (c->irq_flags & IRQF_SHARED) {
-+ /* check if the interrupt is enabled */
-+ flags = readl(c->chan_base + BCM2835_DMA_CS);
-+ /* if not set then we are not the reason for the irq */
-+ if (!(flags & BCM2835_DMA_INT))
-+ return IRQ_NONE;
-+ }
-+
- spin_lock_irqsave(&c->vc.lock, flags);
-
- /* Acknowledge interrupt */
-@@ -506,8 +519,8 @@ static int bcm2835_dma_alloc_chan_resour
- return -ENOMEM;
- }
-
-- return request_irq(c->irq_number,
-- bcm2835_dma_callback, 0, "DMA IRQ", c);
-+ return request_irq(c->irq_number, bcm2835_dma_callback,
-+ c->irq_flags, "DMA IRQ", c);
- }
-
- static void bcm2835_dma_free_chan_resources(struct dma_chan *chan)
-@@ -819,7 +832,8 @@ static int bcm2835_dma_terminate_all(str
- return 0;
- }
-
--static int bcm2835_dma_chan_init(struct bcm2835_dmadev *d, int chan_id, int irq)
-+static int bcm2835_dma_chan_init(struct bcm2835_dmadev *d, int chan_id,
-+ int irq, unsigned int irq_flags)
- {
- struct bcm2835_chan *c;
-
-@@ -834,6 +848,7 @@ static int bcm2835_dma_chan_init(struct
- c->chan_base = BCM2835_DMA_CHANIO(d->base, chan_id);
- c->ch = chan_id;
- c->irq_number = irq;
-+ c->irq_flags = irq_flags;
-
- /* check in DEBUG register if this is a LITE channel */
- if (readl(c->chan_base + BCM2835_DMA_DEBUG) &
-@@ -882,9 +897,11 @@ static int bcm2835_dma_probe(struct plat
- struct resource *res;
- void __iomem *base;
- int rc;
-- int i;
-- int irq;
-+ int i, j;
-+ int irq[BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED + 1];
-+ int irq_flags;
- uint32_t chans_available;
-+ char chan_name[BCM2835_DMA_CHAN_NAME_SIZE];
-
- if (!pdev->dev.dma_mask)
- pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
-@@ -941,16 +958,48 @@ static int bcm2835_dma_probe(struct plat
- goto err_no_dma;
- }
-
-- for (i = 0; i < pdev->num_resources; i++) {
-- irq = platform_get_irq(pdev, i);
-- if (irq < 0)
-- break;
--
-- if (chans_available & (1 << i)) {
-- rc = bcm2835_dma_chan_init(od, i, irq);
-- if (rc)
-- goto err_no_dma;
-+ /* get irqs for each channel that we support */
-+ for (i = 0; i <= BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED; i++) {
-+ /* skip masked out channels */
-+ if (!(chans_available & (1 << i))) {
-+ irq[i] = -1;
-+ continue;
- }
-+
-+ /* get the named irq */
-+ snprintf(chan_name, sizeof(chan_name), "dma%i", i);
-+ irq[i] = platform_get_irq_byname(pdev, chan_name);
-+ if (irq[i] >= 0)
-+ continue;
-+
-+ /* legacy device tree case handling */
-+ dev_warn_once(&pdev->dev,
-+ "missing interrupts-names property in device tree - legacy interpretation is used");
-+ /*
-+ * in case of channel >= 11
-+ * use the 11th interrupt and that is shared
-+ */
-+ irq[i] = platform_get_irq(pdev, i < 11 ? i : 11);
-+ }
-+
-+ /* get irqs for each channel */
-+ for (i = 0; i <= BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED; i++) {
-+ /* skip channels without irq */
-+ if (irq[i] < 0)
-+ continue;
-+
-+ /* check if there are other channels that also use this irq */
-+ irq_flags = 0;
-+ for (j = 0; j <= BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED; j++)
-+ if ((i != j) && (irq[j] == irq[i])) {
-+ irq_flags = IRQF_SHARED;
-+ break;
-+ }
-+
-+ /* initialize the channel */
-+ rc = bcm2835_dma_chan_init(od, i, irq[i], irq_flags);
-+ if (rc)
-+ goto err_no_dma;
- }
-
- dev_dbg(&pdev->dev, "Initialized %i DMA channels\n", i);
diff --git a/target/linux/brcm2708/patches-4.4/0400-dmaengine-bcm2835-Load-driver-early-and-support-lega.patch b/target/linux/brcm2708/patches-4.4/0400-dmaengine-bcm2835-Load-driver-early-and-support-lega.patch
deleted file mode 100644
index 577e937..0000000
--- a/target/linux/brcm2708/patches-4.4/0400-dmaengine-bcm2835-Load-driver-early-and-support-lega.patch
+++ /dev/null
@@ -1,89 +0,0 @@
-From 2de569f13c66b1cfd467f52cce1f01b78422a20b Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Noralf=20Tr=C3=B8nnes?= <noralf at tronnes.org>
-Date: Sat, 3 Oct 2015 22:22:55 +0200
-Subject: [PATCH] dmaengine: bcm2835: Load driver early and support legacy API
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Load driver early since at least bcm2708_fb doesn't support deferred
-probing and even if it did, we don't want the video driver deferred.
-
-Support the legacy DMA API which is needed by bcm2708_fb
-(but only using the dedicated dma channel 0).
-
-Signed-off-by: Noralf Trønnes <noralf at tronnes.org>
-Signed-off-by: Martin Sperl <kernel at martin.sperl.org>
----
- drivers/dma/Kconfig | 2 +-
- drivers/dma/bcm2835-dma.c | 27 ++++++++++++++++++++++++++-
- 2 files changed, 27 insertions(+), 2 deletions(-)
-
---- a/drivers/dma/Kconfig
-+++ b/drivers/dma/Kconfig
-@@ -108,7 +108,7 @@ config COH901318
-
- config DMA_BCM2835
- tristate "BCM2835 DMA engine support"
-- depends on ARCH_BCM2835
-+ depends on ARCH_BCM2835 || ARCH_BCM2708 || ARCH_BCM2709
- select DMA_ENGINE
- select DMA_VIRTUAL_CHANNELS
-
---- a/drivers/dma/bcm2835-dma.c
-+++ b/drivers/dma/bcm2835-dma.c
-@@ -37,6 +37,7 @@
- #include <linux/interrupt.h>
- #include <linux/list.h>
- #include <linux/module.h>
-+#include <linux/platform_data/dma-bcm2708.h>
- #include <linux/platform_device.h>
- #include <linux/slab.h>
- #include <linux/io.h>
-@@ -1021,6 +1022,14 @@ static int bcm2835_dma_probe(struct plat
-
- dev_dbg(&pdev->dev, "Load BCM2835 DMA engine driver\n");
-
-+ /* load the legacy api if bit 0 in the mask is cleared */
-+ if ((chans_available & BIT(0)) == 0) {
-+ rc = bcm_dmaman_probe(pdev, base, BIT(0));
-+ if (rc)
-+ dev_err(&pdev->dev,
-+ "Failed to initialize the legacy API\n");
-+ }
-+
- return 0;
-
- err_no_dma:
-@@ -1032,6 +1041,7 @@ static int bcm2835_dma_remove(struct pla
- {
- struct bcm2835_dmadev *od = platform_get_drvdata(pdev);
-
-+ bcm_dmaman_remove(pdev);
- dma_async_device_unregister(&od->ddev);
- bcm2835_dma_free(od);
-
-@@ -1047,7 +1057,22 @@ static struct platform_driver bcm2835_dm
- },
- };
-
--module_platform_driver(bcm2835_dma_driver);
-+static int bcm2835_dma_init(void)
-+{
-+ return platform_driver_register(&bcm2835_dma_driver);
-+}
-+
-+static void bcm2835_dma_exit(void)
-+{
-+ platform_driver_unregister(&bcm2835_dma_driver);
-+}
-+
-+/*
-+ * Load after serial driver (arch_initcall) so we see the messages if it fails,
-+ * but before drivers (module_init) that need a DMA channel.
-+ */
-+subsys_initcall(bcm2835_dma_init);
-+module_exit(bcm2835_dma_exit);
-
- MODULE_ALIAS("platform:bcm2835-dma");
- MODULE_DESCRIPTION("BCM2835 DMA engine driver");
diff --git a/target/linux/brcm2708/patches-4.4/0401-ARM-bcm270x-changed-bcrm-dma-channel-mask-to-mask-ou.patch b/target/linux/brcm2708/patches-4.4/0401-ARM-bcm270x-changed-bcrm-dma-channel-mask-to-mask-ou.patch
deleted file mode 100644
index e993e4e..0000000
--- a/target/linux/brcm2708/patches-4.4/0401-ARM-bcm270x-changed-bcrm-dma-channel-mask-to-mask-ou.patch
+++ /dev/null
@@ -1,26 +0,0 @@
-From 58934b5badc587bb62659e2862f48bdd77388ff6 Mon Sep 17 00:00:00 2001
-From: Martin Sperl <kernel at martin.sperl.org>
-Date: Fri, 22 Apr 2016 16:13:59 +0000
-Subject: [PATCH] ARM: bcm270x: changed bcrm,dma-channel-mask to mask out the
- used channel
-
-Dma channel0 is used by the legacy api - to avoid confilcts this
-needs to get masked out in the device-tree instead of hardcoding it
-in the driver.
-
-Signed-off-by: Martin Sperl <kernel at martin.sperl.org>
----
- arch/arm/boot/dts/bcm2708_common.dtsi | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/arch/arm/boot/dts/bcm2708_common.dtsi
-+++ b/arch/arm/boot/dts/bcm2708_common.dtsi
-@@ -59,7 +59,7 @@
- <1 27>;
-
- #dma-cells = <1>;
-- brcm,dma-channel-mask = <0x0f35>;
-+ brcm,dma-channel-mask = <0x0f34>;
- };
-
- intc: interrupt-controller at 7e00b200 {
diff --git a/target/linux/brcm2708/patches-4.4/0402-ARM-bcm2835-add-interrupt-names-and-apply-correct-ma.patch b/target/linux/brcm2708/patches-4.4/0402-ARM-bcm2835-add-interrupt-names-and-apply-correct-ma.patch
deleted file mode 100644
index 7a99361..0000000
--- a/target/linux/brcm2708/patches-4.4/0402-ARM-bcm2835-add-interrupt-names-and-apply-correct-ma.patch
+++ /dev/null
@@ -1,50 +0,0 @@
-From 6cbb6897025920aff7536d89e1020afbcc97c340 Mon Sep 17 00:00:00 2001
-From: Martin Sperl <kernel at martin.sperl.org>
-Date: Sat, 23 Apr 2016 14:07:03 +0000
-Subject: [PATCH] ARM: bcm2835: add interrupt-names and apply correct mapping
-
-Add interrupt-names properties to dt and apply the correct
-mapping between irq and dma channels.
-
-Signed-off-by: Martin Sperl <kernel at martin.sperl.org>
----
- arch/arm/boot/dts/bcm2708_common.dtsi | 26 ++++++++++++++++++++++++--
- 1 file changed, 24 insertions(+), 2 deletions(-)
-
---- a/arch/arm/boot/dts/bcm2708_common.dtsi
-+++ b/arch/arm/boot/dts/bcm2708_common.dtsi
-@@ -56,10 +56,32 @@
- <1 24>,
- <1 25>,
- <1 26>,
-- <1 27>;
-+ /* dma channel 11-14 share one irq */
-+ <1 27>,
-+ <1 27>,
-+ <1 27>,
-+ <1 27>,
-+ /* unused shared irq for all channels */
-+ <1 28>;
-+ interrupt-names = "dma0",
-+ "dma1",
-+ "dma2",
-+ "dma3",
-+ "dma4",
-+ "dma5",
-+ "dma6",
-+ "dma7",
-+ "dma8",
-+ "dma9",
-+ "dma10",
-+ "dma11",
-+ "dma12",
-+ "dma13",
-+ "dma14",
-+ "dma-shared-all";
-
- #dma-cells = <1>;
-- brcm,dma-channel-mask = <0x0f34>;
-+ brcm,dma-channel-mask = <0x7f34>;
- };
-
- intc: interrupt-controller at 7e00b200 {
diff --git a/target/linux/brcm2708/patches-4.4/0403-ARM-bcm2835-make-dma-channel-0-available-for-kms-set.patch b/target/linux/brcm2708/patches-4.4/0403-ARM-bcm2835-make-dma-channel-0-available-for-kms-set.patch
deleted file mode 100644
index b93e88a..0000000
--- a/target/linux/brcm2708/patches-4.4/0403-ARM-bcm2835-make-dma-channel-0-available-for-kms-set.patch
+++ /dev/null
@@ -1,28 +0,0 @@
-From c80437416a4a6f914943ada8c23b6891d1d29781 Mon Sep 17 00:00:00 2001
-From: Martin Sperl <kernel at martin.sperl.org>
-Date: Sat, 23 Apr 2016 14:20:41 +0000
-Subject: [PATCH] ARM: bcm2835: make dma-channel-0 available for kms setups
-
-Enable the use of dma-channel 0 when using the vc4-kms-v3d overlay.
-
-Signed-off-by: Martin Sperl <kernel at martin.sperl.org>
----
- arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts | 7 +++++++
- 1 file changed, 7 insertions(+)
-
---- a/arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts
-@@ -119,6 +119,13 @@
- };
- };
-
-+ fragment at 15 {
-+ target-path = "/soc/dma";
-+ __overlay__ {
-+ brcm,dma-channel-mask = <0x7f35>;
-+ };
-+ };
-+
- __overrides__ {
- cma-256 = <0>,"+0-1-2-3-4";
- cma-192 = <0>,"-0+1-2-3-4";
diff --git a/target/linux/brcm2708/patches-4.4/0404-dmaengine-bcm2835-Fix-cyclic-DMA-period-splitting.patch b/target/linux/brcm2708/patches-4.4/0404-dmaengine-bcm2835-Fix-cyclic-DMA-period-splitting.patch
deleted file mode 100644
index 2b6bd99..0000000
--- a/target/linux/brcm2708/patches-4.4/0404-dmaengine-bcm2835-Fix-cyclic-DMA-period-splitting.patch
+++ /dev/null
@@ -1,38 +0,0 @@
-From 9c9db58d0b33e3fd7e67a3fc9910184e6f4d2f95 Mon Sep 17 00:00:00 2001
-From: Matthias Reichl <hias at horus.com>
-Date: Tue, 7 Jun 2016 19:37:10 +0200
-Subject: [PATCH] dmaengine: bcm2835: Fix cyclic DMA period splitting
-
-The code responsible for splitting periods into chunks that
-can be handled by the DMA controller missed to update total_len,
-the number of bytes processed in the current period, when there
-are more chunks to follow.
-
-Therefore total_len was stuck at 0 and the code didn't work at all.
-This resulted in a wrong control block layout and audio issues because
-the cyclic DMA callback wasn't executing on period boundaries.
-
-Fix this by adding the missing total_len update.
-
-Signed-off-by: Matthias Reichl <hias at horus.com>
-Signed-off-by: Martin Sperl <kernel at martin.sperl.org>
-Tested-by: Clive Messer <clive.messer at digitaldreamtime.co.uk>
----
- drivers/dma/bcm2835-dma.c | 5 ++++-
- 1 file changed, 4 insertions(+), 1 deletion(-)
-
---- a/drivers/dma/bcm2835-dma.c
-+++ b/drivers/dma/bcm2835-dma.c
-@@ -252,8 +252,11 @@ static void bcm2835_dma_create_cb_set_le
- */
-
- /* have we filled in period_length yet? */
-- if (*total_len + control_block->length < period_len)
-+ if (*total_len + control_block->length < period_len) {
-+ /* update number of bytes in this period so far */
-+ *total_len += control_block->length;
- return;
-+ }
-
- /* calculate the length that remains to reach period_length */
- control_block->length = period_len - *total_len;
diff --git a/target/linux/brcm2708/patches-4.4/0405-dmaengine-bcm2835-Avoid-splitting-periods-into-very-.patch b/target/linux/brcm2708/patches-4.4/0405-dmaengine-bcm2835-Avoid-splitting-periods-into-very-.patch
deleted file mode 100644
index 6ee4e29..0000000
--- a/target/linux/brcm2708/patches-4.4/0405-dmaengine-bcm2835-Avoid-splitting-periods-into-very-.patch
+++ /dev/null
@@ -1,56 +0,0 @@
-From d9f7bbf7d6f175dc2363c027b931d36fb5e091d1 Mon Sep 17 00:00:00 2001
-From: Matthias Reichl <hias at horus.com>
-Date: Wed, 8 Jun 2016 13:09:56 +0200
-Subject: [PATCH] dmaengine: bcm2835: Avoid splitting periods into very small
- chunks
-
-The current cyclic DMA period splitting implementation can generate
-very small chunks at the end of each period. For example a 65536 byte
-period will be split into a 65532 byte chunk and a 4 byte chunk on
-the "lite" DMA channels.
-
-This increases pressure on the RAM controller as the DMA controller
-needs to fetch two control blocks from RAM in quick succession and
-could potentially cause latency issues if the RAM is tied up by other
-devices.
-
-We can easily avoid these situations by distributing the remaining
-length evenly between the last-but-one and the last chunk, making
-sure that split chunks will be at least half the maximum length the
-DMA controller can handle.
-
-This patch checks if the last chunk would be less than half of
-the maximum DMA length and if yes distributes the max len+4...max_len*1.5
-bytes evenly between the last 2 chunks. This results in chunk sizes
-between max_len/2 and max_len*0.75 bytes.
-
-Signed-off-by: Matthias Reichl <hias at horus.com>
-Signed-off-by: Martin Sperl <kernel at martin.sperl.org>
-Tested-by: Clive Messer <clive.messer at digitaldreamtime.co.uk>
----
- drivers/dma/bcm2835-dma.c | 14 ++++++++++++++
- 1 file changed, 14 insertions(+)
-
---- a/drivers/dma/bcm2835-dma.c
-+++ b/drivers/dma/bcm2835-dma.c
-@@ -253,6 +253,20 @@ static void bcm2835_dma_create_cb_set_le
-
- /* have we filled in period_length yet? */
- if (*total_len + control_block->length < period_len) {
-+ /*
-+ * If the next control block is the last in the period
-+ * and it's length would be less than half of max_len
-+ * change it so that both control blocks are (almost)
-+ * equally long. This avoids generating very short
-+ * control blocks (worst case would be 4 bytes) which
-+ * might be problematic. We also have to make sure the
-+ * new length is a multiple of 4 bytes.
-+ */
-+ if (*total_len + control_block->length + max_len / 2 >
-+ period_len) {
-+ control_block->length =
-+ DIV_ROUND_UP(period_len - *total_len, 8) * 4;
-+ }
- /* update number of bytes in this period so far */
- *total_len += control_block->length;
- return;
diff --git a/target/linux/brcm2708/patches-4.4/0406-dmaengine-bcm2835-Fix-polling-for-completion-of-DMA-.patch b/target/linux/brcm2708/patches-4.4/0406-dmaengine-bcm2835-Fix-polling-for-completion-of-DMA-.patch
deleted file mode 100644
index 77d5d86..0000000
--- a/target/linux/brcm2708/patches-4.4/0406-dmaengine-bcm2835-Fix-polling-for-completion-of-DMA-.patch
+++ /dev/null
@@ -1,68 +0,0 @@
-From 1f38f6d05f4d79a6d13dba29db962e434d4fbb57 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 3 Jun 2016 19:29:11 -0700
-Subject: [PATCH] dmaengine: bcm2835: Fix polling for completion of DMA with
- interrupts masked.
-
-The tx_status hook is supposed to be safe to call from interrupt
-context, but it wouldn't ever return completion for the last transfer,
-meaning you couldn't poll for DMA completion with interrupts masked.
-
-This fixes IRQ handling for bcm2835's DSI1, which requires using the
-DMA engine to write its registers due to a bug in the AXI bridge.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/dma/bcm2835-dma.c | 24 +++++++++++++++++++-----
- 1 file changed, 19 insertions(+), 5 deletions(-)
-
---- a/drivers/dma/bcm2835-dma.c
-+++ b/drivers/dma/bcm2835-dma.c
-@@ -588,16 +588,16 @@ static enum dma_status bcm2835_dma_tx_st
- struct virt_dma_desc *vd;
- enum dma_status ret;
- unsigned long flags;
-+ u32 residue;
-
- ret = dma_cookie_status(chan, cookie, txstate);
-- if (ret == DMA_COMPLETE || !txstate)
-+ if (ret == DMA_COMPLETE)
- return ret;
-
- spin_lock_irqsave(&c->vc.lock, flags);
- vd = vchan_find_desc(&c->vc, cookie);
- if (vd) {
-- txstate->residue =
-- bcm2835_dma_desc_size(to_bcm2835_dma_desc(&vd->tx));
-+ residue = bcm2835_dma_desc_size(to_bcm2835_dma_desc(&vd->tx));
- } else if (c->desc && c->desc->vd.tx.cookie == cookie) {
- struct bcm2835_desc *d = c->desc;
- dma_addr_t pos;
-@@ -609,11 +609,25 @@ static enum dma_status bcm2835_dma_tx_st
- else
- pos = 0;
-
-- txstate->residue = bcm2835_dma_desc_size_pos(d, pos);
-+ residue = bcm2835_dma_desc_size_pos(d, pos);
-+
-+ /*
-+ * If our non-cyclic transfer is done, then report
-+ * complete and trigger the next tx now. This lets
-+ * the dmaengine API be used synchronously from an IRQ
-+ * handler.
-+ */
-+ if (!d->cyclic && residue == 0) {
-+ vchan_cookie_complete(&c->desc->vd);
-+ bcm2835_dma_start_desc(c);
-+ ret = dma_cookie_status(chan, cookie, txstate);
-+ }
- } else {
-- txstate->residue = 0;
-+ residue = 0;
- }
-
-+ dma_set_residue(txstate, residue);
-+
- spin_unlock_irqrestore(&c->vc.lock, flags);
-
- return ret;
diff --git a/target/linux/brcm2708/patches-4.4/0408-BCM270X_DT-Add-spi-rtc-overlay-on-SPI0.0.patch b/target/linux/brcm2708/patches-4.4/0408-BCM270X_DT-Add-spi-rtc-overlay-on-SPI0.0.patch
deleted file mode 100644
index 1801e28..0000000
--- a/target/linux/brcm2708/patches-4.4/0408-BCM270X_DT-Add-spi-rtc-overlay-on-SPI0.0.patch
+++ /dev/null
@@ -1,76 +0,0 @@
-From 14069cf322a96df5b2fdf4ed68510f7d3178bf2e Mon Sep 17 00:00:00 2001
-From: Thomas Kriechbaumer <thomas at kriechbaumer.name>
-Date: Fri, 3 Jun 2016 09:40:44 +0200
-Subject: [PATCH] BCM270X_DT: Add spi-rtc overlay on SPI0.0
-
-Initial version only supports PCF2123 RTC.
-
-See: https://github.com/raspberrypi/linux/pull/1510
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 6 +++++
- arch/arm/boot/dts/overlays/spi-rtc-overlay.dts | 33 ++++++++++++++++++++++++++
- 3 files changed, 40 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/spi-rtc-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -78,6 +78,7 @@ dtbo-$(RPI_DT_OVERLAYS) += smi.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += smi-dev.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += smi-nand.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += spi-gpio35-39.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += spi-rtc.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += spi1-1cs.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += spi1-2cs.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += spi1-3cs.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -975,6 +975,12 @@ Load: dtoverlay=spi-gpio35-39
- Params: <None>
-
-
-+Name: spi-rtc
-+Info: Adds support for a number of SPI Real Time Clock devices
-+Load: dtoverlay=spi-rtc,<param>=<val>
-+Params: pcf2123 Select the PCF2123 device
-+
-+
- Name: spi1-1cs
- Info: Enables spi1 with a single chip select (CS) line and associated spidev
- dev node. The gpio pin number for the CS line and spidev device node
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/spi-rtc-overlay.dts
-@@ -0,0 +1,33 @@
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&spidev0>;
-+ __dormant__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&spi0>;
-+ __dormant__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ rtc-pcf2123 at 0 {
-+ compatible = "nxp,rtc-pcf2123";
-+ spi-max-frequency = <5000000>;
-+ spi-cs-high = <1>;
-+ reg = <0>;
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ pcf2123 = <0>, "=0=1";
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0409-rtc-Add-SPI-alias-for-pcf2123-driver.patch b/target/linux/brcm2708/patches-4.4/0409-rtc-Add-SPI-alias-for-pcf2123-driver.patch
deleted file mode 100644
index 6edf2c6..0000000
--- a/target/linux/brcm2708/patches-4.4/0409-rtc-Add-SPI-alias-for-pcf2123-driver.patch
+++ /dev/null
@@ -1,20 +0,0 @@
-From 61d2f841f7cd5f2a2da3ce8b1497557ba8882157 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Wed, 15 Jun 2016 16:48:41 +0100
-Subject: [PATCH] rtc: Add SPI alias for pcf2123 driver
-
-Without this alias, Device Tree won't cause the driver
-to be loaded.
-
-See: https://github.com/raspberrypi/linux/pull/1510
----
- drivers/rtc/rtc-pcf2123.c | 1 +
- 1 file changed, 1 insertion(+)
-
---- a/drivers/rtc/rtc-pcf2123.c
-+++ b/drivers/rtc/rtc-pcf2123.c
-@@ -358,3 +358,4 @@ MODULE_AUTHOR("Chris Verges <chrisv at cybe
- MODULE_DESCRIPTION("NXP PCF2123 RTC driver");
- MODULE_LICENSE("GPL");
- MODULE_VERSION(DRV_VERSION);
-+MODULE_ALIAS("spi:rtc-pcf2123");
diff --git a/target/linux/brcm2708/patches-4.4/0410-Added-support-for-headphones-microphone-and-bclk_rat.patch b/target/linux/brcm2708/patches-4.4/0410-Added-support-for-headphones-microphone-and-bclk_rat.patch
deleted file mode 100644
index bd8f6e2..0000000
--- a/target/linux/brcm2708/patches-4.4/0410-Added-support-for-headphones-microphone-and-bclk_rat.patch
+++ /dev/null
@@ -1,119 +0,0 @@
-From 40f0914ea3de388781f98620aed9f5f94feccc42 Mon Sep 17 00:00:00 2001
-From: Matt Flax <flatmax at flatmax.org>
-Date: Fri, 17 Jun 2016 12:03:39 +1000
-Subject: [PATCH] Added support for headphones, microphone and bclk_ratio
- settings.
-
-This patch adds headphone and microphone capability to the Audio Injector sound card. The patch also sets the bit clock ratio for use in the bcm2835-i2s driver. The bcm2835-i2s can't handle an 8 kHz sample rate when the bit clock is at 12 MHz because its register is only 10 bits wide which can't represent the ch2 offset of 1508. For that reason, the rate constraint is added.
----
- sound/soc/bcm/audioinjector-pi-soundcard.c | 67 ++++++++++++++++++++++++++----
- 1 file changed, 58 insertions(+), 9 deletions(-)
-
---- a/sound/soc/bcm/audioinjector-pi-soundcard.c
-+++ b/sound/soc/bcm/audioinjector-pi-soundcard.c
-@@ -29,16 +29,56 @@
-
- #include "../codecs/wm8731.h"
-
--static int audioinjector_pi_soundcard_dai_init(struct snd_soc_pcm_runtime *rtd)
-+static const unsigned int bcm2835_rates_12000000[] = {
-+ 32000, 44100, 48000, 96000, 88200,
-+};
-+
-+static struct snd_pcm_hw_constraint_list bcm2835_constraints_12000000 = {
-+ .list = bcm2835_rates_12000000,
-+ .count = ARRAY_SIZE(bcm2835_rates_12000000),
-+};
-+
-+static int snd_audioinjector_pi_soundcard_startup(struct snd_pcm_substream *substream)
- {
-- struct snd_soc_dapm_context *dapm = &rtd->card->dapm;
-+ /* Setup constraints, because there is a 12 MHz XTAL on the board */
-+ snd_pcm_hw_constraint_list(substream->runtime, 0,
-+ SNDRV_PCM_HW_PARAM_RATE,
-+ &bcm2835_constraints_12000000);
-+ return 0;
-+}
-
-- // not connected
-- snd_soc_dapm_nc_pin(dapm, "Mic Bias");
-- snd_soc_dapm_nc_pin(dapm, "MICIN");
-- snd_soc_dapm_nc_pin(dapm, "RHPOUT");
-- snd_soc_dapm_nc_pin(dapm, "LHPOUT");
-+static int snd_audioinjector_pi_soundcard_hw_params(struct snd_pcm_substream *substream,
-+ struct snd_pcm_hw_params *params)
-+{
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
-
-+ switch (params_rate(params)){
-+ case 8000:
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, 1508);
-+ case 32000:
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, 378);
-+ case 44100:
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, 274);
-+ case 48000:
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, 252);
-+ case 88200:
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, 136);
-+ case 96000:
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, 126);
-+ default:
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, 126);
-+ }
-+}
-+
-+/* machine stream operations */
-+static struct snd_soc_ops snd_audioinjector_pi_soundcard_ops = {
-+ .startup = snd_audioinjector_pi_soundcard_startup,
-+ .hw_params = snd_audioinjector_pi_soundcard_hw_params,
-+};
-+
-+static int audioinjector_pi_soundcard_dai_init(struct snd_soc_pcm_runtime *rtd)
-+{
- return snd_soc_dai_set_sysclk(rtd->codec_dai, WM8731_SYSCLK_XTAL, 12000000, SND_SOC_CLOCK_IN);
- }
-
-@@ -50,30 +90,39 @@ static struct snd_soc_dai_link audioinje
- .codec_dai_name = "wm8731-hifi",
- .platform_name = "bcm2835-i2s.0",
- .codec_name = "wm8731.1-001a",
-+ .ops = &snd_audioinjector_pi_soundcard_ops,
- .init = audioinjector_pi_soundcard_dai_init,
- .dai_fmt = SND_SOC_DAIFMT_CBM_CFM|SND_SOC_DAIFMT_I2S|SND_SOC_DAIFMT_NB_NF,
- },
- };
-
- static const struct snd_soc_dapm_widget wm8731_dapm_widgets[] = {
-+ SND_SOC_DAPM_HP("Headphone Jack", NULL),
- SND_SOC_DAPM_SPK("Ext Spk", NULL),
- SND_SOC_DAPM_LINE("Line In Jacks", NULL),
-+ SND_SOC_DAPM_MIC("Microphone", NULL),
- };
-
--/* Corgi machine connections to the codec pins */
- static const struct snd_soc_dapm_route audioinjector_audio_map[] = {
-+ /* headphone connected to LHPOUT, RHPOUT */
-+ {"Headphone Jack", NULL, "LHPOUT"},
-+ {"Headphone Jack", NULL, "RHPOUT"},
-+
- /* speaker connected to LOUT, ROUT */
- {"Ext Spk", NULL, "ROUT"},
- {"Ext Spk", NULL, "LOUT"},
-
- /* line inputs */
- {"Line In Jacks", NULL, "Line Input"},
-+
-+ /* mic is connected to Mic Jack, with WM8731 Mic Bias */
-+ {"Microphone", NULL, "Mic Bias"},
- };
-
- static struct snd_soc_card snd_soc_audioinjector = {
- .name = "audioinjector-pi-soundcard",
- .dai_link = audioinjector_pi_soundcard_dai,
-- .num_links = 1,
-+ .num_links = ARRAY_SIZE(audioinjector_pi_soundcard_dai),
-
- .dapm_widgets = wm8731_dapm_widgets,
- .num_dapm_widgets = ARRAY_SIZE(wm8731_dapm_widgets),
diff --git a/target/linux/brcm2708/patches-4.4/0411-IQaudIO-auto-mute-for-AMP-and-DigiAMP.patch b/target/linux/brcm2708/patches-4.4/0411-IQaudIO-auto-mute-for-AMP-and-DigiAMP.patch
deleted file mode 100644
index 882fa0d..0000000
--- a/target/linux/brcm2708/patches-4.4/0411-IQaudIO-auto-mute-for-AMP-and-DigiAMP.patch
+++ /dev/null
@@ -1,272 +0,0 @@
-From fdf637067ca6a532f785ca4fe54a38caeda39d48 Mon Sep 17 00:00:00 2001
-From: DigitalDreamtime <clive.messer at digitaldreamtime.co.uk>
-Date: Mon, 9 May 2016 20:38:08 +0100
-Subject: [PATCH] IQaudIO: auto-mute for AMP+ and DigiAMP+
-
-IQAudIO amplifier mute via GPIO22. Add dt params for "one-shot" unmute
-and auto mute.
-
-Revision 2, auto mute implementing HiassofT suggestion to mute/unmute
-using set_bias_level, rather than startup/shutdown....
-"By default DAPM waits 5 seconds (pmdown_time) before shutting down
-playback streams so a close/stop immediately followed by open/start
-doesn't trigger an amp mute+unmute."
-
-Tested on both AMP+ (via DAC+) and DigiAMP+, with both options...
-
-dtoverlay=iqaudio-dacplus,unmute_amp
- "one-shot" unmute when kernel module loads.
-
-dtoverlay=iqaudio-dacplus,auto_mute_amp
- Unmute amp when ALSA device opened by a client. Mute, with 5 second delay
- when ALSA device closed. (Re-opening the device within the 5 second close
- window, will cancel mute.)
-
-Revision 4, using gpiod.
-
-Revision 5, clean-up formatting before adding mute code.
- - Convert tab plus 4 space formatting to 2x tab
- - Remove '// NOT USED' commented code
-
-Revision 6, don't attempt to "one-shot" unmute amp, unless card is
-successfully registered.
-
-Signed-off-by: DigitalDreamtime <clive.messer at digitaldreamtime.co.uk>
----
- arch/arm/boot/dts/overlays/README | 4 +
- .../boot/dts/overlays/iqaudio-dacplus-overlay.dts | 7 +-
- sound/soc/bcm/iqaudio-dac.c | 144 ++++++++++++++++-----
- 3 files changed, 124 insertions(+), 31 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -540,6 +540,10 @@ Params: 24db_digital_gain Allow ga
- responsibility of the user to ensure that
- the Digital volume control is set to a value
- that does not result in clipping/distortion!)
-+ auto_mute_amp If specified, unmute/mute the IQaudIO amp when
-+ starting/stopping audio playback.
-+ unmute_amp If specified, unmute the IQaudIO amp once when
-+ the DAC driver module loads.
-
-
- Name: justboom-dac
---- a/arch/arm/boot/dts/overlays/iqaudio-dacplus-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/iqaudio-dacplus-overlay.dts
-@@ -30,14 +30,17 @@
-
- fragment at 2 {
- target = <&sound>;
-- frag2: __overlay__ {
-+ iqaudio_dac: __overlay__ {
- compatible = "iqaudio,iqaudio-dac";
- i2s-controller = <&i2s>;
-+ mute-gpios = <&gpio 22 0>;
- status = "okay";
- };
- };
-
- __overrides__ {
-- 24db_digital_gain = <&frag2>,"iqaudio,24db_digital_gain?";
-+ 24db_digital_gain = <&iqaudio_dac>,"iqaudio,24db_digital_gain?";
-+ auto_mute_amp = <&iqaudio_dac>,"iqaudio-dac,auto-mute-amp?";
-+ unmute_amp = <&iqaudio_dac>,"iqaudio-dac,unmute-amp?";
- };
- };
---- a/sound/soc/bcm/iqaudio-dac.c
-+++ b/sound/soc/bcm/iqaudio-dac.c
-@@ -15,6 +15,7 @@
- */
-
- #include <linux/module.h>
-+#include <linux/gpio/consumer.h>
- #include <linux/platform_device.h>
-
- #include <sound/core.h>
-@@ -25,6 +26,8 @@
-
- static bool digital_gain_0db_limit = true;
-
-+static struct gpio_desc *mute_gpio;
-+
- static int snd_rpi_iqaudio_dac_init(struct snd_soc_pcm_runtime *rtd)
- {
- if (digital_gain_0db_limit)
-@@ -41,11 +44,9 @@ static int snd_rpi_iqaudio_dac_init(stru
- }
-
- static int snd_rpi_iqaudio_dac_hw_params(struct snd_pcm_substream *substream,
-- struct snd_pcm_hw_params *params)
-+ struct snd_pcm_hw_params *params)
- {
- struct snd_soc_pcm_runtime *rtd = substream->private_data;
--// NOT USED struct snd_soc_dai *codec_dai = rtd->codec_dai;
--// NOT USED struct snd_soc_codec *codec = rtd->codec;
- struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
-
- unsigned int sample_bits =
-@@ -54,6 +55,56 @@ static int snd_rpi_iqaudio_dac_hw_params
- return snd_soc_dai_set_bclk_ratio(cpu_dai, sample_bits * 2);
- }
-
-+static void snd_rpi_iqaudio_gpio_mute(struct snd_soc_card *card)
-+{
-+ if (mute_gpio) {
-+ dev_info(card->dev, "%s: muting amp using GPIO22\n",
-+ __func__);
-+ gpiod_set_value_cansleep(mute_gpio, 0);
-+ }
-+}
-+
-+static void snd_rpi_iqaudio_gpio_unmute(struct snd_soc_card *card)
-+{
-+ if (mute_gpio) {
-+ dev_info(card->dev, "%s: un-muting amp using GPIO22\n",
-+ __func__);
-+ gpiod_set_value_cansleep(mute_gpio, 1);
-+ }
-+}
-+
-+static int snd_rpi_iqaudio_set_bias_level(struct snd_soc_card *card,
-+ struct snd_soc_dapm_context *dapm, enum snd_soc_bias_level level)
-+{
-+ struct snd_soc_dai *codec_dai = card->rtd[0].codec_dai;
-+
-+ if (dapm->dev != codec_dai->dev)
-+ return 0;
-+
-+ switch (level) {
-+ case SND_SOC_BIAS_PREPARE:
-+ if (dapm->bias_level != SND_SOC_BIAS_STANDBY)
-+ break;
-+
-+ /* UNMUTE AMP */
-+ snd_rpi_iqaudio_gpio_unmute(card);
-+
-+ break;
-+ case SND_SOC_BIAS_STANDBY:
-+ if (dapm->bias_level != SND_SOC_BIAS_PREPARE)
-+ break;
-+
-+ /* MUTE AMP */
-+ snd_rpi_iqaudio_gpio_mute(card);
-+
-+ break;
-+ default:
-+ break;
-+ }
-+
-+ return 0;
-+}
-+
- /* machine stream operations */
- static struct snd_soc_ops snd_rpi_iqaudio_dac_ops = {
- .hw_params = snd_rpi_iqaudio_dac_hw_params,
-@@ -82,46 +133,81 @@ static struct snd_soc_card snd_rpi_iqaud
- static int snd_rpi_iqaudio_dac_probe(struct platform_device *pdev)
- {
- int ret = 0;
-+ bool gpio_unmute = false;
-
- snd_rpi_iqaudio_dac.dev = &pdev->dev;
-
- if (pdev->dev.of_node) {
-- struct device_node *i2s_node;
-- struct snd_soc_card *card = &snd_rpi_iqaudio_dac;
-- struct snd_soc_dai_link *dai = &snd_rpi_iqaudio_dac_dai[0];
-- i2s_node = of_parse_phandle(pdev->dev.of_node,
-- "i2s-controller", 0);
--
-- if (i2s_node) {
-- dai->cpu_dai_name = NULL;
-- dai->cpu_of_node = i2s_node;
-- dai->platform_name = NULL;
-- dai->platform_of_node = i2s_node;
-- }
--
-- digital_gain_0db_limit = !of_property_read_bool(pdev->dev.of_node,
-- "iqaudio,24db_digital_gain");
-- if (of_property_read_string(pdev->dev.of_node, "card_name",
-- &card->name))
-- card->name = "IQaudIODAC";
-- if (of_property_read_string(pdev->dev.of_node, "dai_name",
-- &dai->name))
-- dai->name = "IQaudIO DAC";
-- if (of_property_read_string(pdev->dev.of_node, "dai_stream_name",
-- &dai->stream_name))
-- dai->stream_name = "IQaudIO DAC HiFi";
-+ struct device_node *i2s_node;
-+ struct snd_soc_card *card = &snd_rpi_iqaudio_dac;
-+ struct snd_soc_dai_link *dai = &snd_rpi_iqaudio_dac_dai[0];
-+ bool auto_gpio_mute = false;
-+
-+ i2s_node = of_parse_phandle(pdev->dev.of_node,
-+ "i2s-controller", 0);
-+ if (i2s_node) {
-+ dai->cpu_dai_name = NULL;
-+ dai->cpu_of_node = i2s_node;
-+ dai->platform_name = NULL;
-+ dai->platform_of_node = i2s_node;
-+ }
-+
-+ digital_gain_0db_limit = !of_property_read_bool(
-+ pdev->dev.of_node, "iqaudio,24db_digital_gain");
-+
-+ if (of_property_read_string(pdev->dev.of_node, "card_name",
-+ &card->name))
-+ card->name = "IQaudIODAC";
-+
-+ if (of_property_read_string(pdev->dev.of_node, "dai_name",
-+ &dai->name))
-+ dai->name = "IQaudIO DAC";
-+
-+ if (of_property_read_string(pdev->dev.of_node,
-+ "dai_stream_name", &dai->stream_name))
-+ dai->stream_name = "IQaudIO DAC HiFi";
-+
-+ /* gpio_unmute - one time unmute amp using GPIO */
-+ gpio_unmute = of_property_read_bool(pdev->dev.of_node,
-+ "iqaudio-dac,unmute-amp");
-+
-+ /* auto_gpio_mute - mute/unmute amp using GPIO */
-+ auto_gpio_mute = of_property_read_bool(pdev->dev.of_node,
-+ "iqaudio-dac,auto-mute-amp");
-+
-+ if (auto_gpio_mute || gpio_unmute) {
-+ mute_gpio = devm_gpiod_get_optional(&pdev->dev, "mute",
-+ GPIOD_OUT_LOW);
-+ if (IS_ERR(mute_gpio)) {
-+ ret = PTR_ERR(mute_gpio);
-+ dev_err(&pdev->dev,
-+ "Failed to get mute gpio: %d\n", ret);
-+ return ret;
-+ }
-+
-+ if (auto_gpio_mute && mute_gpio)
-+ snd_rpi_iqaudio_dac.set_bias_level =
-+ snd_rpi_iqaudio_set_bias_level;
-+ }
- }
-
- ret = snd_soc_register_card(&snd_rpi_iqaudio_dac);
-- if (ret)
-+ if (ret) {
- dev_err(&pdev->dev,
- "snd_soc_register_card() failed: %d\n", ret);
-+ return ret;
-+ }
-+
-+ if (gpio_unmute && mute_gpio)
-+ snd_rpi_iqaudio_gpio_unmute(&snd_rpi_iqaudio_dac);
-
-- return ret;
-+ return 0;
- }
-
- static int snd_rpi_iqaudio_dac_remove(struct platform_device *pdev)
- {
-+ snd_rpi_iqaudio_gpio_mute(&snd_rpi_iqaudio_dac);
-+
- return snd_soc_unregister_card(&snd_rpi_iqaudio_dac);
- }
-
diff --git a/target/linux/brcm2708/patches-4.4/0412-mmc-Apply-ERASE_BROKEN-quirks-correctly.patch b/target/linux/brcm2708/patches-4.4/0412-mmc-Apply-ERASE_BROKEN-quirks-correctly.patch
deleted file mode 100644
index 36801e3..0000000
--- a/target/linux/brcm2708/patches-4.4/0412-mmc-Apply-ERASE_BROKEN-quirks-correctly.patch
+++ /dev/null
@@ -1,28 +0,0 @@
-From 13fe4901709c5d7b8bad28d60292f507e5d19b4d Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Thu, 23 Jun 2016 16:37:46 +0100
-Subject: [PATCH] mmc: Apply ERASE_BROKEN quirks correctly
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- drivers/mmc/card/block.c | 9 +++------
- 1 file changed, 3 insertions(+), 6 deletions(-)
-
---- a/drivers/mmc/card/block.c
-+++ b/drivers/mmc/card/block.c
-@@ -2564,12 +2564,9 @@ static const struct mmc_fixup blk_fixups
- * On some Kingston SD cards, multiple erases of less than 64
- * sectors can cause corruption.
- */
-- MMC_FIXUP("SD16G", 0x41, 0x3432, add_quirk_mmc,
-- MMC_QUIRK_ERASE_BROKEN),
-- MMC_FIXUP("SD32G", 0x41, 0x3432, add_quirk_mmc,
-- MMC_QUIRK_ERASE_BROKEN),
-- MMC_FIXUP("SD64G", 0x41, 0x3432, add_quirk_mmc,
-- MMC_QUIRK_ERASE_BROKEN),
-+ MMC_FIXUP("SD16G", 0x41, 0x3432, add_quirk, MMC_QUIRK_ERASE_BROKEN),
-+ MMC_FIXUP("SD32G", 0x41, 0x3432, add_quirk, MMC_QUIRK_ERASE_BROKEN),
-+ MMC_FIXUP("SD64G", 0x41, 0x3432, add_quirk, MMC_QUIRK_ERASE_BROKEN),
-
- END_FIXUP
- };
diff --git a/target/linux/brcm2708/patches-4.4/0413-enable-led-support-for-xpad-driver-fixes-flashing-le.patch b/target/linux/brcm2708/patches-4.4/0413-enable-led-support-for-xpad-driver-fixes-flashing-le.patch
deleted file mode 100644
index 58b3757..0000000
--- a/target/linux/brcm2708/patches-4.4/0413-enable-led-support-for-xpad-driver-fixes-flashing-le.patch
+++ /dev/null
@@ -1,31 +0,0 @@
-From 8ad248ba91135b0a710e2b1a8b520f93c3810af6 Mon Sep 17 00:00:00 2001
-From: Jools Wills <buzz at exotica.org.uk>
-Date: Sun, 26 Jun 2016 16:28:48 +0000
-Subject: [PATCH] enable led support for xpad driver - fixes flashing leds on
- controller
-
----
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 2 files changed, 2 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -559,6 +559,7 @@ CONFIG_JOYSTICK_IFORCE=m
- CONFIG_JOYSTICK_IFORCE_USB=y
- CONFIG_JOYSTICK_XPAD=m
- CONFIG_JOYSTICK_XPAD_FF=y
-+CONFIG_JOYSTICK_XPAD_LEDS=y
- CONFIG_JOYSTICK_RPISENSE=m
- CONFIG_INPUT_TOUCHSCREEN=y
- CONFIG_TOUCHSCREEN_ADS7846=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -552,6 +552,7 @@ CONFIG_JOYSTICK_IFORCE=m
- CONFIG_JOYSTICK_IFORCE_USB=y
- CONFIG_JOYSTICK_XPAD=m
- CONFIG_JOYSTICK_XPAD_FF=y
-+CONFIG_JOYSTICK_XPAD_LEDS=y
- CONFIG_JOYSTICK_RPISENSE=m
- CONFIG_INPUT_TOUCHSCREEN=y
- CONFIG_TOUCHSCREEN_ADS7846=m
diff --git a/target/linux/brcm2708/patches-4.4/0414-Add-critical-information-for-getting-pi3-miniuart-bt.patch b/target/linux/brcm2708/patches-4.4/0414-Add-critical-information-for-getting-pi3-miniuart-bt.patch
deleted file mode 100644
index d8c813e..0000000
--- a/target/linux/brcm2708/patches-4.4/0414-Add-critical-information-for-getting-pi3-miniuart-bt.patch
+++ /dev/null
@@ -1,25 +0,0 @@
-From c9b8a3517364a417cf3c7bbfb051e3155d2ec99a Mon Sep 17 00:00:00 2001
-From: David Lechner <david at lechnology.com>
-Date: Mon, 27 Jun 2016 22:52:22 -0500
-Subject: [PATCH] Add critical information for getting pi3-miniuart-bt overlay
- to work
-
-Bluetooth on RPi 3 using uart1 will not work without setting core_freq=250 in config.txt. This is not
-documented anywhere, so this seems like a good place to start.
----
- arch/arm/boot/dts/overlays/README | 4 +++-
- 1 file changed, 3 insertions(+), 1 deletion(-)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -691,7 +691,9 @@ Info: Switch Pi3 Bluetooth function to
- N.B. It is also necessary to edit /lib/systemd/system/hciuart.service
- and replace ttyAMA0 with ttyS0, unless you have a system with udev rules
- that create /dev/serial0 and /dev/serial1, in which case use
-- /dev/serial1 instead because it will always be correct.
-+ /dev/serial1 instead because it will always be correct. Furthermore,
-+ you must also set core_freq=250 in config.txt or the miniuart will not
-+ work.
- Load: dtoverlay=pi3-miniuart-bt
- Params: <None>
-
diff --git a/target/linux/brcm2708/patches-4.4/0415-bcm2835-sdhost-Improvements-to-error-recovery.patch b/target/linux/brcm2708/patches-4.4/0415-bcm2835-sdhost-Improvements-to-error-recovery.patch
deleted file mode 100644
index 88d9d4d..0000000
--- a/target/linux/brcm2708/patches-4.4/0415-bcm2835-sdhost-Improvements-to-error-recovery.patch
+++ /dev/null
@@ -1,312 +0,0 @@
-From edeb743e7562d9fa4d5f19c557bf558036031973 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Wed, 15 Jun 2016 17:13:55 +0100
-Subject: [PATCH] bcm2835-sdhost: Improvements to error recovery
-
-1) Try to avoid reducing overclock when a card is removed.
-
-2) Reset overclock on card insertion.
-
-3) Reduce logging when errors occur, lowering the severity of
- some messages and making others conditional on the debug
- flag.
-
-4) Attempt to identify a disconnected SD bus earlier, treating a
- zero returned OCR (voltage support) as an error condition.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- drivers/mmc/host/bcm2835-sdhost.c | 117 ++++++++++++++++++++++++--------------
- 1 file changed, 74 insertions(+), 43 deletions(-)
-
---- a/drivers/mmc/host/bcm2835-sdhost.c
-+++ b/drivers/mmc/host/bcm2835-sdhost.c
-@@ -38,6 +38,7 @@
- #include <linux/mmc/mmc.h>
- #include <linux/mmc/host.h>
- #include <linux/mmc/sd.h>
-+#include <linux/mmc/sdio.h>
- #include <linux/scatterlist.h>
- #include <linux/of_address.h>
- #include <linux/of_irq.h>
-@@ -206,6 +207,7 @@ struct bcm2835_host {
- struct timeval stop_time; /* when the last stop was issued */
- u32 delay_after_stop; /* minimum time between stop and subsequent data transfer */
- u32 delay_after_this_stop; /* minimum time between this stop and subsequent data transfer */
-+ u32 user_overclock_50; /* User's preferred frequency to use when 50MHz is requested (in MHz) */
- u32 overclock_50; /* frequency to use when 50MHz is requested (in MHz) */
- u32 overclock; /* Current frequency if overclocked, else zero */
- u32 pio_limit; /* Maximum block count for PIO (0 = always DMA) */
-@@ -282,7 +284,7 @@ static void log_dump(void)
- do {
- entry = sdhost_log_buf + idx;
- if (entry->event[0] != '\0')
-- pr_err("[%08x] %.4s %x %x\n",
-+ pr_info("[%08x] %.4s %x %x\n",
- entry->timestamp,
- entry->event,
- entry->param1,
-@@ -324,7 +326,7 @@ static void bcm2835_sdhost_dumpcmd(struc
- const char *label)
- {
- if (cmd)
-- pr_err("%s:%c%s op %d arg 0x%x flags 0x%x - resp %08x %08x %08x %08x, err %d\n",
-+ pr_info("%s:%c%s op %d arg 0x%x flags 0x%x - resp %08x %08x %08x %08x, err %d\n",
- mmc_hostname(host->mmc),
- (cmd == host->cmd) ? '>' : ' ',
- label, cmd->opcode, cmd->arg, cmd->flags,
-@@ -339,7 +341,7 @@ static void bcm2835_sdhost_dumpregs(stru
- bcm2835_sdhost_dumpcmd(host, host->mrq->sbc, "sbc");
- bcm2835_sdhost_dumpcmd(host, host->mrq->cmd, "cmd");
- if (host->mrq->data)
-- pr_err("%s: data blocks %x blksz %x - err %d\n",
-+ pr_info("%s: data blocks %x blksz %x - err %d\n",
- mmc_hostname(host->mmc),
- host->mrq->data->blocks,
- host->mrq->data->blksz,
-@@ -347,53 +349,53 @@ static void bcm2835_sdhost_dumpregs(stru
- bcm2835_sdhost_dumpcmd(host, host->mrq->stop, "stop");
- }
-
-- pr_err("%s: =========== REGISTER DUMP ===========\n",
-+ pr_info("%s: =========== REGISTER DUMP ===========\n",
- mmc_hostname(host->mmc));
-
-- pr_err("%s: SDCMD 0x%08x\n",
-+ pr_info("%s: SDCMD 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDCMD));
-- pr_err("%s: SDARG 0x%08x\n",
-+ pr_info("%s: SDARG 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDARG));
-- pr_err("%s: SDTOUT 0x%08x\n",
-+ pr_info("%s: SDTOUT 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDTOUT));
-- pr_err("%s: SDCDIV 0x%08x\n",
-+ pr_info("%s: SDCDIV 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDCDIV));
-- pr_err("%s: SDRSP0 0x%08x\n",
-+ pr_info("%s: SDRSP0 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDRSP0));
-- pr_err("%s: SDRSP1 0x%08x\n",
-+ pr_info("%s: SDRSP1 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDRSP1));
-- pr_err("%s: SDRSP2 0x%08x\n",
-+ pr_info("%s: SDRSP2 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDRSP2));
- pr_err("%s: SDRSP3 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDRSP3));
-- pr_err("%s: SDHSTS 0x%08x\n",
-+ pr_info("%s: SDHSTS 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDHSTS));
-- pr_err("%s: SDVDD 0x%08x\n",
-+ pr_info("%s: SDVDD 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDVDD));
-- pr_err("%s: SDEDM 0x%08x\n",
-+ pr_info("%s: SDEDM 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDEDM));
-- pr_err("%s: SDHCFG 0x%08x\n",
-+ pr_info("%s: SDHCFG 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDHCFG));
-- pr_err("%s: SDHBCT 0x%08x\n",
-+ pr_info("%s: SDHBCT 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDHBCT));
-- pr_err("%s: SDHBLC 0x%08x\n",
-+ pr_info("%s: SDHBLC 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDHBLC));
-
-- pr_err("%s: ===========================================\n",
-+ pr_info("%s: ===========================================\n",
- mmc_hostname(host->mmc));
- }
-
-@@ -608,7 +610,7 @@ static void bcm2835_sdhost_read_block_pi
- (fsm_state != SDEDM_FSM_READCRC)) {
- hsts = bcm2835_sdhost_read(host,
- SDHSTS);
-- pr_err("%s: fsm %x, hsts %x\n",
-+ pr_info("%s: fsm %x, hsts %x\n",
- mmc_hostname(host->mmc),
- fsm_state, hsts);
- if (hsts & SDHSTS_ERROR_MASK)
-@@ -698,7 +700,7 @@ static void bcm2835_sdhost_write_block_p
- (fsm_state != SDEDM_FSM_WRITESTART2)) {
- hsts = bcm2835_sdhost_read(host,
- SDHSTS);
-- pr_err("%s: fsm %x, hsts %x\n",
-+ pr_info("%s: fsm %x, hsts %x\n",
- mmc_hostname(host->mmc),
- fsm_state, hsts);
- if (hsts & SDHSTS_ERROR_MASK)
-@@ -953,9 +955,10 @@ bool bcm2835_sdhost_send_command(struct
-
- while (bcm2835_sdhost_read(host, SDCMD) & SDCMD_NEW_FLAG) {
- if (timeout == 0) {
-- pr_err("%s: previous command never completed.\n",
-+ pr_warn("%s: previous command never completed.\n",
- mmc_hostname(host->mmc));
-- bcm2835_sdhost_dumpregs(host);
-+ if (host->debug)
-+ bcm2835_sdhost_dumpregs(host);
- cmd->error = -EILSEQ;
- tasklet_schedule(&host->finish_tasklet);
- return false;
-@@ -1213,10 +1216,12 @@ static void bcm2835_sdhost_finish_comman
-
- /* Check for errors */
- if (sdcmd & SDCMD_NEW_FLAG) {
-- pr_err("%s: command never completed.\n",
-- mmc_hostname(host->mmc));
-- bcm2835_sdhost_dumpregs(host);
-- host->cmd->error = -EIO;
-+ if (host->debug) {
-+ pr_err("%s: command %d never completed.\n",
-+ mmc_hostname(host->mmc), host->cmd->opcode);
-+ bcm2835_sdhost_dumpregs(host);
-+ }
-+ host->cmd->error = -EILSEQ;
- tasklet_schedule(&host->finish_tasklet);
- return;
- } else if (sdcmd & SDCMD_FAIL_FLAG) {
-@@ -1238,15 +1243,14 @@ static void bcm2835_sdhost_finish_comman
- } else {
- if (sdhsts & SDHSTS_CMD_TIME_OUT) {
- if (host->debug)
-- pr_err("%s: command %d timeout\n",
-+ pr_warn("%s: command %d timeout\n",
- mmc_hostname(host->mmc),
- host->cmd->opcode);
- host->cmd->error = -ETIMEDOUT;
- } else {
-- pr_err("%s: unexpected command %d error\n",
-+ pr_warn("%s: unexpected command %d error\n",
- mmc_hostname(host->mmc),
- host->cmd->opcode);
-- bcm2835_sdhost_dumpregs(host);
- host->cmd->error = -EILSEQ;
- }
- tasklet_schedule(&host->finish_tasklet);
-@@ -1370,8 +1374,10 @@ static void bcm2835_sdhost_busy_irq(stru
- } else if (intmask & SDHSTS_CMD_TIME_OUT)
- host->cmd->error = -ETIMEDOUT;
-
-- log_dump();
-- bcm2835_sdhost_dumpregs(host);
-+ if (host->debug) {
-+ log_dump();
-+ bcm2835_sdhost_dumpregs(host);
-+ }
- }
- else
- bcm2835_sdhost_finish_command(host, NULL);
-@@ -1595,7 +1601,7 @@ void bcm2835_sdhost_set_clock(struct bcm
- host->overclock_50 = (clock/MHZ);
-
- if (clock != host->overclock) {
-- pr_warn("%s: overclocking to %dHz\n",
-+ pr_info("%s: overclocking to %dHz\n",
- mmc_hostname(host->mmc), clock);
- host->overclock = clock;
- }
-@@ -1605,6 +1611,11 @@ void bcm2835_sdhost_set_clock(struct bcm
- pr_warn("%s: cancelling overclock\n",
- mmc_hostname(host->mmc));
- }
-+ } else if (input_clock == 0) {
-+ /* Reset the preferred overclock when the clock is stopped.
-+ * This always happens during initialisation. */
-+ host->overclock_50 = host->user_overclock_50;
-+ host->overclock = 0;
- }
-
- /* Set the timeout to 500ms */
-@@ -1678,13 +1689,15 @@ static void bcm2835_sdhost_request(struc
- log_event("REQ<", (u32)mrq, edm);
- if ((fsm != SDEDM_FSM_IDENTMODE) &&
- (fsm != SDEDM_FSM_DATAMODE)) {
-- pr_err("%s: previous command (%d) not complete (EDM %x)\n",
-- mmc_hostname(host->mmc),
-- bcm2835_sdhost_read(host, SDCMD) & SDCMD_CMD_MASK,
-- edm);
- log_event("REQ!", (u32)mrq, edm);
-- log_dump();
-- bcm2835_sdhost_dumpregs(host);
-+ if (host->debug) {
-+ pr_warn("%s: previous command (%d) not complete (EDM %x)\n",
-+ mmc_hostname(host->mmc),
-+ bcm2835_sdhost_read(host, SDCMD) & SDCMD_CMD_MASK,
-+ edm);
-+ log_dump();
-+ bcm2835_sdhost_dumpregs(host);
-+ }
- mrq->cmd->error = -EILSEQ;
- tasklet_schedule(&host->finish_tasklet);
- mmiowb();
-@@ -1814,16 +1827,19 @@ static void bcm2835_sdhost_tasklet_finis
- mrq = host->mrq;
-
- /* Drop the overclock after any data corruption, or after any
-- error overclocked */
-+ * error while overclocked. Ignore errors for status commands,
-+ * as they are likely when a card is ejected. */
- if (host->overclock) {
-- if ((mrq->cmd && mrq->cmd->error) ||
-+ if ((mrq->cmd && mrq->cmd->error &&
-+ (mrq->cmd->opcode != MMC_SEND_STATUS)) ||
- (mrq->data && mrq->data->error) ||
-- (mrq->stop && mrq->stop->error)) {
-+ (mrq->stop && mrq->stop->error) ||
-+ (mrq->sbc && mrq->sbc->error)) {
- host->overclock_50--;
- pr_warn("%s: reducing overclock due to errors\n",
- mmc_hostname(host->mmc));
- host->reset_clock = 1;
-- mrq->cmd->error = -EILSEQ;
-+ mrq->cmd->error = -ETIMEDOUT;
- mrq->cmd->retries = 1;
- }
- }
-@@ -1848,6 +1864,21 @@ static void bcm2835_sdhost_tasklet_finis
- mmc_hostname(host->mmc), err);
- }
-
-+ /* The SDHOST block doesn't report any errors for a disconnected
-+ interface. All cards and SDIO devices should report some supported
-+ voltage range, so a zero response to SEND_OP_COND, IO_SEND_OP_COND
-+ or APP_SEND_OP_COND can be treated as an error. */
-+ if (((mrq->cmd->opcode == MMC_SEND_OP_COND) ||
-+ (mrq->cmd->opcode == SD_IO_SEND_OP_COND) ||
-+ (mrq->cmd->opcode == SD_APP_OP_COND)) &&
-+ (mrq->cmd->error == 0) &&
-+ (mrq->cmd->resp[0] == 0)) {
-+ mrq->cmd->error = -ETIMEDOUT;
-+ if (host->debug)
-+ pr_info("%s: faking timeout due to zero OCR\n",
-+ mmc_hostname(host->mmc));
-+ }
-+
- mmc_request_done(host->mmc, mrq);
- log_event("TSK>", (u32)mrq, 0);
- }
-@@ -2023,7 +2054,7 @@ static int bcm2835_sdhost_probe(struct p
- &host->delay_after_stop);
- of_property_read_u32(node,
- "brcm,overclock-50",
-- &host->overclock_50);
-+ &host->user_overclock_50);
- of_property_read_u32(node,
- "brcm,pio-limit",
- &host->pio_limit);
diff --git a/target/linux/brcm2708/patches-4.4/0416-pinctrl-bcm2835-Fix-return-type-of-bcm2835_pmx_free.patch b/target/linux/brcm2708/patches-4.4/0416-pinctrl-bcm2835-Fix-return-type-of-bcm2835_pmx_free.patch
deleted file mode 100644
index be2bbaa..0000000
--- a/target/linux/brcm2708/patches-4.4/0416-pinctrl-bcm2835-Fix-return-type-of-bcm2835_pmx_free.patch
+++ /dev/null
@@ -1,27 +0,0 @@
-From 6e3a6683d7da4fcb31a9e6eae5f9c50dab62da31 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Tue, 28 Jun 2016 22:13:15 +0100
-Subject: [PATCH] pinctrl-bcm2835: Fix return type of bcm2835_pmx_free
-
----
- drivers/pinctrl/bcm/pinctrl-bcm2835.c | 3 ++-
- 1 file changed, 2 insertions(+), 1 deletion(-)
-
---- a/drivers/pinctrl/bcm/pinctrl-bcm2835.c
-+++ b/drivers/pinctrl/bcm/pinctrl-bcm2835.c
-@@ -831,13 +831,14 @@ static const struct pinctrl_ops bcm2835_
- .dt_free_map = bcm2835_pctl_dt_free_map,
- };
-
--static void bcm2835_pmx_free(struct pinctrl_dev *pctldev,
-+static int bcm2835_pmx_free(struct pinctrl_dev *pctldev,
- unsigned offset)
- {
- struct bcm2835_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev);
-
- /* disable by setting to GPIO_IN */
- bcm2835_pinctrl_fsel_set(pc, offset, BCM2835_FSEL_GPIO_IN);
-+ return 0;
- }
-
- static int bcm2835_pmx_get_functions_count(struct pinctrl_dev *pctldev)
diff --git a/target/linux/brcm2708/patches-4.4/0417-Add-IQAudIO-Digi-WM8804-board-support.patch b/target/linux/brcm2708/patches-4.4/0417-Add-IQAudIO-Digi-WM8804-board-support.patch
deleted file mode 100644
index 92a6996..0000000
--- a/target/linux/brcm2708/patches-4.4/0417-Add-IQAudIO-Digi-WM8804-board-support.patch
+++ /dev/null
@@ -1,399 +0,0 @@
-From 3baa4a62b02b106fd49bb02fc1791a9467004e43 Mon Sep 17 00:00:00 2001
-From: DigitalDreamtime <clive.messer at digitaldreamtime.co.uk>
-Date: Thu, 30 Jun 2016 18:38:42 +0100
-Subject: [PATCH] Add IQAudIO Digi WM8804 board support
-
-Support IQAudIO Digi board with iqaudio_digi machine driver and
- iqaudio-digi-wm8804-audio overlay.
-
-NB. Machine driver is a cut and paste of hifiberry_digi code, with format
- and general cleanup to comply with kernel coding standards.
-
-Signed-off-by: DigitalDreamtime <clive.messer at digitaldreamtime.co.uk>
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 9 +
- .../overlays/iqaudio-digi-wm8804-audio-overlay.dts | 47 ++++
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- sound/soc/bcm/Kconfig | 7 +
- sound/soc/bcm/Makefile | 2 +
- sound/soc/bcm/iqaudio_digi.c | 239 +++++++++++++++++++++
- 8 files changed, 307 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/iqaudio-digi-wm8804-audio-overlay.dts
- create mode 100644 sound/soc/bcm/iqaudio_digi.c
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -42,6 +42,7 @@ dtbo-$(RPI_DT_OVERLAYS) += i2s-gpio28-31
- dtbo-$(RPI_DT_OVERLAYS) += i2s-mmap.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += iqaudio-dac.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += iqaudio-dacplus.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += iqaudio-digi-wm8804-audio.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += justboom-dac.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += justboom-digi.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += lirc-rpi.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -546,6 +546,15 @@ Params: 24db_digital_gain Allow ga
- the DAC driver module loads.
-
-
-+Name: iqaudio-digi-wm8804-audio
-+Info: Configures the IQAudIO Digi WM8804 audio card
-+Load: dtoverlay=iqaudio-digi-wm8804-audio,<param>=<val>
-+Params: card_name Override the default, "IQAudIODigi", card name.
-+ dai_name Override the default, "IQAudIO Digi", dai name.
-+ dai_stream_name Override the default, "IQAudIO Digi HiFi",
-+ dai stream name.
-+
-+
- Name: justboom-dac
- Info: Configures the JustBoom DAC HAT, Amp HAT, DAC Zero and Amp Zero audio
- cards
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/iqaudio-digi-wm8804-audio-overlay.dts
-@@ -0,0 +1,47 @@
-+// Definitions for IQAudIO Digi WM8804 audio board
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&i2s>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&i2c1>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ wm8804 at 3b {
-+ #sound-dai-cells = <0>;
-+ compatible = "wlf,wm8804";
-+ reg = <0x3b>;
-+ status = "okay";
-+ // DVDD-supply = <®_3v3>;
-+ // PVDD-supply = <®_3v3>;
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&sound>;
-+ wm8804_digi: __overlay__ {
-+ compatible = "iqaudio,wm8804-digi";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
-+
-+ __overrides__ {
-+ card_name = <&wm8804_digi>,"wm8804-digi,card-name";
-+ dai_name = <&wm8804_digi>,"wm8804-digi,dai-name";
-+ dai_stream_name = <&wm8804_digi>,"wm8804-digi,dai-stream-name";
-+ };
-+};
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -865,6 +865,7 @@ CONFIG_SND_BCM2708_SOC_RPI_PROTO=m
- CONFIG_SND_BCM2708_SOC_JUSTBOOM_DAC=m
- CONFIG_SND_BCM2708_SOC_JUSTBOOM_DIGI=m
- CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC=m
-+CONFIG_SND_BCM2708_SOC_IQAUDIO_DIGI=m
- CONFIG_SND_BCM2708_SOC_RASPIDAC3=m
- CONFIG_SND_AUDIOINJECTOR_PI_SOUNDCARD=m
- CONFIG_SND_DIGIDAC1_SOUNDCARD=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -857,6 +857,7 @@ CONFIG_SND_BCM2708_SOC_RPI_PROTO=m
- CONFIG_SND_BCM2708_SOC_JUSTBOOM_DAC=m
- CONFIG_SND_BCM2708_SOC_JUSTBOOM_DIGI=m
- CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC=m
-+CONFIG_SND_BCM2708_SOC_IQAUDIO_DIGI=m
- CONFIG_SND_BCM2708_SOC_RASPIDAC3=m
- CONFIG_SND_AUDIOINJECTOR_PI_SOUNDCARD=m
- CONFIG_SND_DIGIDAC1_SOUNDCARD=m
---- a/sound/soc/bcm/Kconfig
-+++ b/sound/soc/bcm/Kconfig
-@@ -71,6 +71,13 @@ config SND_BCM2708_SOC_IQAUDIO_DAC
- help
- Say Y or M if you want to add support for IQaudIO-DAC.
-
-+config SND_BCM2708_SOC_IQAUDIO_DIGI
-+ tristate "Support for IQAudIO Digi"
-+ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
-+ select SND_SOC_WM8804
-+ help
-+ Say Y or M if you want to add support for IQAudIO Digital IO board.
-+
- config SND_BCM2708_SOC_RASPIDAC3
- tristate "Support for RaspiDAC Rev.3x"
- depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
---- a/sound/soc/bcm/Makefile
-+++ b/sound/soc/bcm/Makefile
-@@ -14,6 +14,7 @@ snd-soc-justboom-digi-objs := justboom-d
- snd-soc-rpi-dac-objs := rpi-dac.o
- snd-soc-rpi-proto-objs := rpi-proto.o
- snd-soc-iqaudio-dac-objs := iqaudio-dac.o
-+snd-soc-iqaudio-digi-objs := iqaudio_digi.o
- snd-soc-raspidac3-objs := raspidac3.o
- snd-soc-audioinjector-pi-soundcard-objs := audioinjector-pi-soundcard.o
- snd-soc-digidac1-soundcard-objs := digidac1-soundcard.o
-@@ -28,6 +29,7 @@ obj-$(CONFIG_SND_BCM2708_SOC_JUSTBOOM_DI
- obj-$(CONFIG_SND_BCM2708_SOC_RPI_DAC) += snd-soc-rpi-dac.o
- obj-$(CONFIG_SND_BCM2708_SOC_RPI_PROTO) += snd-soc-rpi-proto.o
- obj-$(CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC) += snd-soc-iqaudio-dac.o
-+obj-$(CONFIG_SND_BCM2708_SOC_IQAUDIO_DIGI) += snd-soc-iqaudio-digi.o
- obj-$(CONFIG_SND_BCM2708_SOC_RASPIDAC3) += snd-soc-raspidac3.o
- obj-$(CONFIG_SND_AUDIOINJECTOR_PI_SOUNDCARD) += snd-soc-audioinjector-pi-soundcard.o
- obj-$(CONFIG_SND_DIGIDAC1_SOUNDCARD) += snd-soc-digidac1-soundcard.o
---- /dev/null
-+++ b/sound/soc/bcm/iqaudio_digi.c
-@@ -0,0 +1,239 @@
-+/*
-+ * ASoC Driver for IQAudIO WM8804 Digi
-+ *
-+ * Author: Daniel Matuschek <info at crazy-audio.com>
-+ * based on the HifiBerry DAC driver by Florian Meier <florian.meier at koalo.de>
-+ * Copyright 2013
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * version 2 as published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful, but
-+ * WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
-+ * General Public License for more details.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+
-+#include <sound/core.h>
-+#include <sound/pcm.h>
-+#include <sound/pcm_params.h>
-+#include <sound/soc.h>
-+#include <sound/jack.h>
-+
-+#include "../codecs/wm8804.h"
-+
-+static short int auto_shutdown_output;
-+module_param(auto_shutdown_output, short,
-+ S_IRUSR | S_IWUSR | S_IRGRP | S_IWGRP);
-+MODULE_PARM_DESC(auto_shutdown_output, "Shutdown SP/DIF output if playback is stopped");
-+
-+static int snd_rpi_iqaudio_digi_init(struct snd_soc_pcm_runtime *rtd)
-+{
-+ struct snd_soc_codec *codec = rtd->codec;
-+
-+ /* enable TX output */
-+ snd_soc_update_bits(codec, WM8804_PWRDN, 0x4, 0x0);
-+
-+ return 0;
-+}
-+
-+static int snd_rpi_iqaudio_digi_startup(struct snd_pcm_substream *substream)
-+{
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_codec *codec = rtd->codec;
-+
-+ /* turn on digital output */
-+ snd_soc_update_bits(codec, WM8804_PWRDN, 0x3c, 0x00);
-+
-+ return 0;
-+}
-+
-+static void snd_rpi_iqaudio_digi_shutdown(struct snd_pcm_substream *substream)
-+{
-+ if (auto_shutdown_output) {
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_codec *codec = rtd->codec;
-+
-+ /* turn off digital output */
-+ snd_soc_update_bits(codec, WM8804_PWRDN, 0x3c, 0x3c);
-+ }
-+}
-+
-+
-+static int snd_rpi_iqaudio_digi_hw_params(struct snd_pcm_substream *substream,
-+ struct snd_pcm_hw_params *params)
-+{
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_dai *codec_dai = rtd->codec_dai;
-+ struct snd_soc_codec *codec = rtd->codec;
-+ struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
-+
-+ int sysclk = 27000000; /* This is fixed on this board */
-+
-+ long mclk_freq = 0;
-+ int mclk_div = 1;
-+ int sampling_freq = 1;
-+
-+ int ret;
-+
-+ int samplerate = params_rate(params);
-+
-+ if (samplerate <= 96000) {
-+ mclk_freq = samplerate * 256;
-+ mclk_div = WM8804_MCLKDIV_256FS;
-+ } else {
-+ mclk_freq = samplerate * 128;
-+ mclk_div = WM8804_MCLKDIV_128FS;
-+ }
-+
-+ switch (samplerate) {
-+ case 32000:
-+ sampling_freq = 0x03;
-+ break;
-+ case 44100:
-+ sampling_freq = 0x00;
-+ break;
-+ case 48000:
-+ sampling_freq = 0x02;
-+ break;
-+ case 88200:
-+ sampling_freq = 0x08;
-+ break;
-+ case 96000:
-+ sampling_freq = 0x0a;
-+ break;
-+ case 176400:
-+ sampling_freq = 0x0c;
-+ break;
-+ case 192000:
-+ sampling_freq = 0x0e;
-+ break;
-+ default:
-+ dev_err(codec->dev, "Failed to set WM8804 SYSCLK, unsupported samplerate %d\n",
-+ samplerate);
-+ }
-+
-+ snd_soc_dai_set_clkdiv(codec_dai, WM8804_MCLK_DIV, mclk_div);
-+ snd_soc_dai_set_pll(codec_dai, 0, 0, sysclk, mclk_freq);
-+
-+ ret = snd_soc_dai_set_sysclk(codec_dai, WM8804_TX_CLKSRC_PLL,
-+ sysclk, SND_SOC_CLOCK_OUT);
-+ if (ret < 0) {
-+ dev_err(codec->dev, "Failed to set WM8804 SYSCLK: %d\n", ret);
-+ return ret;
-+ }
-+
-+ /* Enable TX output */
-+ snd_soc_update_bits(codec, WM8804_PWRDN, 0x4, 0x0);
-+
-+ /* Power on */
-+ snd_soc_update_bits(codec, WM8804_PWRDN, 0x9, 0);
-+
-+ /* set sampling frequency status bits */
-+ snd_soc_update_bits(codec, WM8804_SPDTX4, 0x0f, sampling_freq);
-+
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, 64);
-+}
-+
-+/* machine stream operations */
-+static struct snd_soc_ops snd_rpi_iqaudio_digi_ops = {
-+ .hw_params = snd_rpi_iqaudio_digi_hw_params,
-+ .startup = snd_rpi_iqaudio_digi_startup,
-+ .shutdown = snd_rpi_iqaudio_digi_shutdown,
-+};
-+
-+static struct snd_soc_dai_link snd_rpi_iqaudio_digi_dai[] = {
-+{
-+ .name = "IQAudIO Digi",
-+ .stream_name = "IQAudIO Digi HiFi",
-+ .cpu_dai_name = "bcm2708-i2s.0",
-+ .codec_dai_name = "wm8804-spdif",
-+ .platform_name = "bcm2708-i2s.0",
-+ .codec_name = "wm8804.1-003b",
-+ .dai_fmt = SND_SOC_DAIFMT_I2S |
-+ SND_SOC_DAIFMT_NB_NF |
-+ SND_SOC_DAIFMT_CBM_CFM,
-+ .ops = &snd_rpi_iqaudio_digi_ops,
-+ .init = snd_rpi_iqaudio_digi_init,
-+},
-+};
-+
-+/* audio machine driver */
-+static struct snd_soc_card snd_rpi_iqaudio_digi = {
-+ .name = "IQAudIODigi",
-+ .owner = THIS_MODULE,
-+ .dai_link = snd_rpi_iqaudio_digi_dai,
-+ .num_links = ARRAY_SIZE(snd_rpi_iqaudio_digi_dai),
-+};
-+
-+static int snd_rpi_iqaudio_digi_probe(struct platform_device *pdev)
-+{
-+ struct snd_soc_card *card = &snd_rpi_iqaudio_digi;
-+ char *prefix = "wm8804-digi,";
-+ char prop[128];
-+ struct device_node *np;
-+ int ret = 0;
-+
-+ snd_rpi_iqaudio_digi.dev = &pdev->dev;
-+
-+ np = pdev->dev.of_node;
-+ if (np) {
-+ struct snd_soc_dai_link *dai = &snd_rpi_iqaudio_digi_dai[0];
-+ struct device_node *i2s_node;
-+
-+ i2s_node = of_parse_phandle(np, "i2s-controller", 0);
-+ if (i2s_node) {
-+ dai->cpu_dai_name = NULL;
-+ dai->cpu_of_node = i2s_node;
-+ dai->platform_name = NULL;
-+ dai->platform_of_node = i2s_node;
-+ }
-+
-+ snprintf(prop, sizeof(prop), "%scard-name", prefix);
-+ of_property_read_string(np, prop, &card->name);
-+
-+ snprintf(prop, sizeof(prop), "%sdai-name", prefix);
-+ of_property_read_string(np, prop, &dai->name);
-+
-+ snprintf(prop, sizeof(prop), "%sdai-stream-name", prefix);
-+ of_property_read_string(np, prop, &dai->stream_name);
-+ }
-+
-+ ret = snd_soc_register_card(card);
-+ if (ret)
-+ dev_err(&pdev->dev, "snd_soc_register_card() failed: %d\n",
-+ ret);
-+
-+ return ret;
-+}
-+
-+static int snd_rpi_iqaudio_digi_remove(struct platform_device *pdev)
-+{
-+ return snd_soc_unregister_card(&snd_rpi_iqaudio_digi);
-+}
-+
-+static const struct of_device_id snd_rpi_iqaudio_digi_of_match[] = {
-+ { .compatible = "iqaudio,wm8804-digi", },
-+ {},
-+};
-+MODULE_DEVICE_TABLE(of, snd_rpi_iqaudio_digi_of_match);
-+
-+static struct platform_driver snd_rpi_iqaudio_digi_driver = {
-+ .driver = {
-+ .name = "IQAudIODigi",
-+ .owner = THIS_MODULE,
-+ .of_match_table = snd_rpi_iqaudio_digi_of_match,
-+ },
-+ .probe = snd_rpi_iqaudio_digi_probe,
-+ .remove = snd_rpi_iqaudio_digi_remove,
-+};
-+
-+module_platform_driver(snd_rpi_iqaudio_digi_driver);
-+
-+MODULE_AUTHOR("Daniel Matuschek <info at crazy-audio.com>");
-+MODULE_DESCRIPTION("ASoC Driver for IQAudIO WM8804 Digi");
-+MODULE_LICENSE("GPL v2");
diff --git a/target/linux/brcm2708/patches-4.4/0418-dts-Add-overlay-for-NXP-SC16IS752-Dual-UART-with-SPI.patch b/target/linux/brcm2708/patches-4.4/0418-dts-Add-overlay-for-NXP-SC16IS752-Dual-UART-with-SPI.patch
deleted file mode 100644
index 3650047..0000000
--- a/target/linux/brcm2708/patches-4.4/0418-dts-Add-overlay-for-NXP-SC16IS752-Dual-UART-with-SPI.patch
+++ /dev/null
@@ -1,106 +0,0 @@
-From 23074d03200bc35acdb2ebd8a127fb6b832307fc Mon Sep 17 00:00:00 2001
-From: Erdem MEYDANLI <erdem.meydanli at punica.com.tr>
-Date: Thu, 30 Jun 2016 21:05:08 +0300
-Subject: [PATCH] dts: Add overlay for NXP SC16IS752 Dual UART with SPI
- Interface
-
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 10 ++++
- .../boot/dts/overlays/sc16is752-spi1-overlay.dts | 61 ++++++++++++++++++++++
- 3 files changed, 72 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/sc16is752-spi1-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -71,6 +71,7 @@ dtbo-$(RPI_DT_OVERLAYS) += rpi-ft5406.dt
- dtbo-$(RPI_DT_OVERLAYS) += rpi-proto.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += rpi-sense.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += rra-digidac1-wm8741-audio.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += sc16is752-spi1.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += sdhost.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += sdio.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += sdio-1bit.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -888,6 +888,16 @@ Load: dtoverlay=rra-digidac1-wm8741-au
- Params: <None>
-
-
-+Name: sc16is752-spi1
-+Info: Overlay for the NXP SC16IS752 Dual UART with SPI Interface
-+ Enables the chip on SPI1.
-+ N.B.: spi1 is only accessible on devices with a 40pin header, eg:
-+ A+, B+, Zero and PI2 B; as well as the Compute Module.
-+
-+Load: dtoverlay=sc16is752-spi1,<param>=<val>
-+Params: int_pin GPIO used for IRQ (default 24)
-+
-+
- Name: sdhost
- Info: Selects the bcm2835-sdhost SD/MMC driver, optionally with overclock.
- N.B. This overlay is designed for situations where the mmc driver is
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/sc16is752-spi1-overlay.dts
-@@ -0,0 +1,61 @@
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ spi1_pins: spi1_pins {
-+ brcm,pins = <19 20 21>;
-+ brcm,function = <3>; /* alt4 */
-+ };
-+
-+ spi1_cs_pins: spi1_cs_pins {
-+ brcm,pins = <18>;
-+ brcm,function = <1>; /* output */
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&spi1>;
-+ frag1: __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&spi1_pins &spi1_cs_pins>;
-+ cs-gpios = <&gpio 18 1>;
-+ status = "okay";
-+
-+ sc16is752: sc16is752 at 0 {
-+ compatible = "nxp,sc16is752";
-+ reg = <0>; /* CE0 */
-+ clocks = <&sc16is752_clk>;
-+ interrupt-parent = <&gpio>;
-+ interrupts = <24 2>; /* IRQ_TYPE_EDGE_FALLING */
-+ #gpio-controller;
-+ #gpio-cells = <2>;
-+ spi-max-frequency = <4000000>;
-+
-+ sc16is752_clk: sc16is752_clk {
-+ compatible = "fixed-clock";
-+ #clock-cells = <0>;
-+ clock-frequency = <14745600>;
-+ };
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&aux>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ __overrides__ {
-+ int_pin = <&sc16is752>,"interrupts:0";
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0419-spi-bcm2835-Disable-forced-software-CS.patch b/target/linux/brcm2708/patches-4.4/0419-spi-bcm2835-Disable-forced-software-CS.patch
deleted file mode 100644
index 567788f..0000000
--- a/target/linux/brcm2708/patches-4.4/0419-spi-bcm2835-Disable-forced-software-CS.patch
+++ /dev/null
@@ -1,46 +0,0 @@
-From 5f2b7d1bf699505b07eb5b05e3ad4c2619b1f578 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 1 Jul 2016 22:09:24 +0100
-Subject: [PATCH] spi-bcm2835: Disable forced software CS
-
-Select software CS in bcm2708_common.dtsi, and disable the automatic
-conversion in the driver to allow hardware CS to be re-enabled with an
-overlay.
-
-See: https://github.com/raspberrypi/linux/issues/1547
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/bcm2708_common.dtsi | 2 +-
- drivers/spi/spi-bcm2835.c | 2 ++
- 2 files changed, 3 insertions(+), 1 deletion(-)
-
---- a/arch/arm/boot/dts/bcm2708_common.dtsi
-+++ b/arch/arm/boot/dts/bcm2708_common.dtsi
-@@ -183,7 +183,7 @@
- * add more gpios if necessary as <&gpio 6 1>
- * (but do not forget to make them output!)
- */
-- cs-gpios = <0>, <0>;
-+ cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
- };
-
- i2c0: i2c at 7e205000 {
---- a/drivers/spi/spi-bcm2835.c
-+++ b/drivers/spi/spi-bcm2835.c
-@@ -707,6 +707,7 @@ static int bcm2835_spi_setup(struct spi_
- return -EINVAL;
- }
-
-+#if 0
- /* now translate native cs to GPIO */
- /* first look for chip select pins in the devices pin groups */
- for (pingroup_index = 0;
-@@ -761,6 +762,7 @@ static int bcm2835_spi_setup(struct spi_
- * so we are setting it here explicitly
- */
- gpio_set_value(spi->cs_gpio, (spi->mode & SPI_CS_HIGH) ? 0 : 1);
-+#endif
-
- return 0;
- }
diff --git a/target/linux/brcm2708/patches-4.4/0420-BCM270X_DT-Overlay-to-re-enable-HW-CS-on-SPI0.patch b/target/linux/brcm2708/patches-4.4/0420-BCM270X_DT-Overlay-to-re-enable-HW-CS-on-SPI0.patch
deleted file mode 100644
index 257d8a1..0000000
--- a/target/linux/brcm2708/patches-4.4/0420-BCM270X_DT-Overlay-to-re-enable-HW-CS-on-SPI0.patch
+++ /dev/null
@@ -1,69 +0,0 @@
-From 2dcbb03d4f8bc425af50505140a9fac2103afb0c Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 1 Jul 2016 22:34:52 +0100
-Subject: [PATCH] BCM270X_DT: Overlay to re-enable HW CS on SPI0
-
-See: https://github.com/raspberrypi/linux/issues/1547
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 6 ++++++
- arch/arm/boot/dts/overlays/spi0-hw-cs-overlay.dts | 26 +++++++++++++++++++++++
- 3 files changed, 33 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/spi0-hw-cs-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -81,6 +81,7 @@ dtbo-$(RPI_DT_OVERLAYS) += smi-dev.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += smi-nand.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += spi-gpio35-39.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += spi-rtc.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += spi0-hw-cs.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += spi1-1cs.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += spi1-2cs.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += spi1-3cs.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -1006,6 +1006,12 @@ Load: dtoverlay=spi-rtc,<param>=<val>
- Params: pcf2123 Select the PCF2123 device
-
-
-+Name: spi0-hw-cs
-+Info: Re-enables hardware CS/CE (chip selects) for SPI0
-+Load: dtoverlay=spi0-hw-cs
-+Params: <None>
-+
-+
- Name: spi1-1cs
- Info: Enables spi1 with a single chip select (CS) line and associated spidev
- dev node. The gpio pin number for the CS line and spidev device node
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/spi0-hw-cs-overlay.dts
-@@ -0,0 +1,26 @@
-+/*
-+ * Device tree overlay to re-enable hardware CS for SPI0
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2836", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ cs-gpios = <0>, <0>;
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&spi0_cs_pins>;
-+ __overlay__ {
-+ brcm,pins = <8 7>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0421-Add-support-for-Dion-Audio-LOCO-DAC-AMP-HAT.patch b/target/linux/brcm2708/patches-4.4/0421-Add-support-for-Dion-Audio-LOCO-DAC-AMP-HAT.patch
deleted file mode 100644
index dffcef5..0000000
--- a/target/linux/brcm2708/patches-4.4/0421-Add-support-for-Dion-Audio-LOCO-DAC-AMP-HAT.patch
+++ /dev/null
@@ -1,261 +0,0 @@
-From 01eedb8b865d19d9cd00799a6e657b0e00b26b2d Mon Sep 17 00:00:00 2001
-From: DigitalDreamtime <clive.messer at digitaldreamtime.co.uk>
-Date: Sat, 2 Jul 2016 16:26:19 +0100
-Subject: [PATCH] Add support for Dion Audio LOCO DAC-AMP HAT
-
-Using dedicated machine driver and pcm5102a codec driver.
-
-Signed-off-by: DigitalDreamtime <clive.messer at digitaldreamtime.co.uk>
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 6 +
- .../boot/dts/overlays/dionaudio-loco-overlay.dts | 39 +++++++
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- sound/soc/bcm/Kconfig | 7 ++
- sound/soc/bcm/Makefile | 3 +-
- sound/soc/bcm/dionaudio_loco.c | 121 +++++++++++++++++++++
- 8 files changed, 178 insertions(+), 1 deletion(-)
- create mode 100644 arch/arm/boot/dts/overlays/dionaudio-loco-overlay.dts
- create mode 100644 sound/soc/bcm/dionaudio_loco.c
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -20,6 +20,7 @@ dtbo-$(RPI_DT_OVERLAYS) += at86rf233.dtb
- dtbo-$(RPI_DT_OVERLAYS) += audioinjector-wm8731-audio.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += bmp085_i2c-sensor.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += dht11.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += dionaudio-loco.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += dpi24.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += dwc-otg.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += dwc2.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -268,6 +268,12 @@ Params: gpiopin GPIO con
- (default 4)
-
-
-+Name: dionaudio-loco
-+Info: Configures the Dion Audio LOCO DAC-AMP
-+Load: dtoverlay=dionaudio-loco
-+Params: <None>
-+
-+
- Name: dpi24
- Info: Overlay for a generic 24-bit DPI display
- This uses GPIOs 0-27 (so no I2C, uart etc.), and activates the output
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/dionaudio-loco-overlay.dts
-@@ -0,0 +1,39 @@
-+// Definitions for Dion Audio LOCO DAC-AMP
-+
-+/*
-+ * PCM5242 DAC (in hardware mode) and TPA3118 AMP.
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&i2s>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target-path = "/";
-+ __overlay__ {
-+ pcm5102a-codec {
-+ #sound-dai-cells = <0>;
-+ compatible = "ti,pcm5102a";
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&sound>;
-+ __overlay__ {
-+ compatible = "dionaudio,loco-pcm5242-tpa3118";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
-+};
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -870,6 +870,7 @@ CONFIG_SND_BCM2708_SOC_RASPIDAC3=m
- CONFIG_SND_AUDIOINJECTOR_PI_SOUNDCARD=m
- CONFIG_SND_DIGIDAC1_SOUNDCARD=m
- CONFIG_SND_BCM2708_SOC_ADAU1977_ADC=m
-+CONFIG_SND_BCM2708_SOC_DIONAUDIO_LOCO=m
- CONFIG_SND_SOC_ADAU1701=m
- CONFIG_SND_SOC_WM8804_I2C=m
- CONFIG_SND_SIMPLE_CARD=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -862,6 +862,7 @@ CONFIG_SND_BCM2708_SOC_RASPIDAC3=m
- CONFIG_SND_AUDIOINJECTOR_PI_SOUNDCARD=m
- CONFIG_SND_DIGIDAC1_SOUNDCARD=m
- CONFIG_SND_BCM2708_SOC_ADAU1977_ADC=m
-+CONFIG_SND_BCM2708_SOC_DIONAUDIO_LOCO=m
- CONFIG_SND_SOC_ADAU1701=m
- CONFIG_SND_SOC_WM8804_I2C=m
- CONFIG_SND_SIMPLE_CARD=m
---- a/sound/soc/bcm/Kconfig
-+++ b/sound/soc/bcm/Kconfig
-@@ -107,3 +107,10 @@ config SND_DIGIDAC1_SOUNDCARD
- select SND_SOC_WM8741
- help
- Say Y or M if you want to add support for Red Rocks Audio DigiDAC1 board.
-+
-+config SND_BCM2708_SOC_DIONAUDIO_LOCO
-+ tristate "Support for Dion Audio LOCO DAC-AMP"
-+ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
-+ select SND_SOC_PCM5102a
-+ help
-+ Say Y or M if you want to add support for Dion Audio LOCO.
---- a/sound/soc/bcm/Makefile
-+++ b/sound/soc/bcm/Makefile
-@@ -18,6 +18,7 @@ snd-soc-iqaudio-digi-objs := iqaudio_dig
- snd-soc-raspidac3-objs := raspidac3.o
- snd-soc-audioinjector-pi-soundcard-objs := audioinjector-pi-soundcard.o
- snd-soc-digidac1-soundcard-objs := digidac1-soundcard.o
-+snd-soc-dionaudio-loco-objs := dionaudio_loco.o
-
- obj-$(CONFIG_SND_BCM2708_SOC_ADAU1977_ADC) += snd-soc-adau1977-adc.o
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DAC) += snd-soc-hifiberry-dac.o
-@@ -33,4 +34,4 @@ obj-$(CONFIG_SND_BCM2708_SOC_IQAUDIO_DIG
- obj-$(CONFIG_SND_BCM2708_SOC_RASPIDAC3) += snd-soc-raspidac3.o
- obj-$(CONFIG_SND_AUDIOINJECTOR_PI_SOUNDCARD) += snd-soc-audioinjector-pi-soundcard.o
- obj-$(CONFIG_SND_DIGIDAC1_SOUNDCARD) += snd-soc-digidac1-soundcard.o
--
-+obj-$(CONFIG_SND_BCM2708_SOC_DIONAUDIO_LOCO) += snd-soc-dionaudio-loco.o
---- /dev/null
-+++ b/sound/soc/bcm/dionaudio_loco.c
-@@ -0,0 +1,121 @@
-+/*
-+ * ASoC Driver for Dion Audio LOCO DAC-AMP
-+ *
-+ * Author: Miquel Blauw <info at dionaudio.nl>
-+ * Copyright 2016
-+ *
-+ * Based on the software of the RPi-DAC writen by Florian Meier
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * version 2 as published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful, but
-+ * WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
-+ * General Public License for more details.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+
-+#include <sound/core.h>
-+#include <sound/pcm.h>
-+#include <sound/pcm_params.h>
-+#include <sound/soc.h>
-+#include <sound/jack.h>
-+
-+static int snd_rpi_dionaudio_loco_hw_params(
-+ struct snd_pcm_substream *substream, struct snd_pcm_hw_params *params)
-+{
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
-+
-+ unsigned int sample_bits =
-+ snd_pcm_format_physical_width(params_format(params));
-+
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, sample_bits * 2);
-+}
-+
-+/* machine stream operations */
-+static struct snd_soc_ops snd_rpi_dionaudio_loco_ops = {
-+ .hw_params = snd_rpi_dionaudio_loco_hw_params,
-+};
-+
-+static struct snd_soc_dai_link snd_rpi_dionaudio_loco_dai[] = {
-+{
-+ .name = "DionAudio LOCO",
-+ .stream_name = "DionAudio LOCO DAC-AMP",
-+ .cpu_dai_name = "bcm2708-i2s.0",
-+ .codec_dai_name = "pcm5102a-hifi",
-+ .platform_name = "bcm2708-i2s.0",
-+ .codec_name = "pcm5102a-codec",
-+ .dai_fmt = SND_SOC_DAIFMT_I2S |
-+ SND_SOC_DAIFMT_NB_NF |
-+ SND_SOC_DAIFMT_CBS_CFS,
-+ .ops = &snd_rpi_dionaudio_loco_ops,
-+},
-+};
-+
-+/* audio machine driver */
-+static struct snd_soc_card snd_rpi_dionaudio_loco = {
-+ .name = "snd_rpi_dionaudio_loco",
-+ .dai_link = snd_rpi_dionaudio_loco_dai,
-+ .num_links = ARRAY_SIZE(snd_rpi_dionaudio_loco_dai),
-+};
-+
-+static int snd_rpi_dionaudio_loco_probe(struct platform_device *pdev)
-+{
-+ struct device_node *np;
-+ int ret = 0;
-+
-+ snd_rpi_dionaudio_loco.dev = &pdev->dev;
-+
-+ np = pdev->dev.of_node;
-+ if (np) {
-+ struct snd_soc_dai_link *dai = &snd_rpi_dionaudio_loco_dai[0];
-+ struct device_node *i2s_np;
-+
-+ i2s_np = of_parse_phandle(np, "i2s-controller", 0);
-+ if (i2s_np) {
-+ dai->cpu_dai_name = NULL;
-+ dai->cpu_of_node = i2s_np;
-+ dai->platform_name = NULL;
-+ dai->platform_of_node = i2s_np;
-+ }
-+ }
-+
-+ ret = snd_soc_register_card(&snd_rpi_dionaudio_loco);
-+ if (ret)
-+ dev_err(&pdev->dev, "snd_soc_register_card() failed: %d\n",
-+ ret);
-+
-+ return ret;
-+}
-+
-+static int snd_rpi_dionaudio_loco_remove(struct platform_device *pdev)
-+{
-+ return snd_soc_unregister_card(&snd_rpi_dionaudio_loco);
-+}
-+
-+static const struct of_device_id snd_rpi_dionaudio_loco_of_match[] = {
-+ { .compatible = "dionaudio,loco-pcm5242-tpa3118", },
-+ { /* sentinel */ },
-+};
-+MODULE_DEVICE_TABLE(of, snd_rpi_dionaudio_loco_of_match);
-+
-+static struct platform_driver snd_rpi_dionaudio_loco_driver = {
-+ .driver = {
-+ .name = "snd-dionaudio-loco",
-+ .owner = THIS_MODULE,
-+ .of_match_table = snd_rpi_dionaudio_loco_of_match,
-+ },
-+ .probe = snd_rpi_dionaudio_loco_probe,
-+ .remove = snd_rpi_dionaudio_loco_remove,
-+};
-+
-+module_platform_driver(snd_rpi_dionaudio_loco_driver);
-+
-+MODULE_AUTHOR("Miquel Blauw <info at dionaudio.nl>");
-+MODULE_DESCRIPTION("ASoC Driver for DionAudio LOCO");
-+MODULE_LICENSE("GPL v2");
diff --git a/target/linux/brcm2708/patches-4.4/0422-ASoc-wm8731-add-32bit-mode.patch b/target/linux/brcm2708/patches-4.4/0422-ASoc-wm8731-add-32bit-mode.patch
deleted file mode 100644
index f487525..0000000
--- a/target/linux/brcm2708/patches-4.4/0422-ASoc-wm8731-add-32bit-mode.patch
+++ /dev/null
@@ -1,39 +0,0 @@
-From 78bfece00f4edb5d13e4e066c66e1c5903b69986 Mon Sep 17 00:00:00 2001
-From: Matt Flax <flatmax at flatmax.org>
-Date: Fri, 17 Jun 2016 14:48:16 +1000
-Subject: [PATCH] ASoc: wm8731: add 32bit mode.
-
-commit cf5ef3a299ba32f6ac24c3c6ba18c1b7f1b5475f upstream.
-
-This patch adds 32 bit word capability to the wm8731 driver. The wm8731
-codec is capable of handling 32 bit word sizes, however that has not
-previously been activated in the codec driver.
-
-Signed-off-by: Matt Flax <flatmax at flatmax.org>
-Acked-by: Charles Keepax <ckeepax at opensource.wolfsonmicro.com>
-Signed-off-by: Mark Brown <broonie at kernel.org>
----
- sound/soc/codecs/wm8731.c | 5 ++++-
- 1 file changed, 4 insertions(+), 1 deletion(-)
-
---- a/sound/soc/codecs/wm8731.c
-+++ b/sound/soc/codecs/wm8731.c
-@@ -358,6 +358,9 @@ static int wm8731_hw_params(struct snd_p
- case 24:
- iface |= 0x0008;
- break;
-+ case 32:
-+ iface |= 0x000c;
-+ break;
- }
-
- wm8731_set_deemph(codec);
-@@ -541,7 +544,7 @@ static int wm8731_startup(struct snd_pcm
- #define WM8731_RATES SNDRV_PCM_RATE_8000_96000
-
- #define WM8731_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S20_3LE |\
-- SNDRV_PCM_FMTBIT_S24_LE)
-+ SNDRV_PCM_FMTBIT_S24_LE | SNDRV_PCM_FMTBIT_S32_LE)
-
- static const struct snd_soc_dai_ops wm8731_dai_ops = {
- .startup = wm8731_startup,
diff --git a/target/linux/brcm2708/patches-4.4/0423-BCM270X_DT-Declare-the-audio-PWM-pins-explicitly.patch b/target/linux/brcm2708/patches-4.4/0423-BCM270X_DT-Declare-the-audio-PWM-pins-explicitly.patch
deleted file mode 100644
index f558f2d..0000000
--- a/target/linux/brcm2708/patches-4.4/0423-BCM270X_DT-Declare-the-audio-PWM-pins-explicitly.patch
+++ /dev/null
@@ -1,122 +0,0 @@
-From b7ed9ed6bebe864e6a52f25e82c337448d1e44fc Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 20 Jun 2016 13:21:26 +0100
-Subject: [PATCH] BCM270X_DT: Declare the audio PWM pins explicitly
-
-Make the audio driver's use of the PWM functions explicit. Overlays
-that want to use the PWM functionality for other purposes must
-disable the audio node.
-
-See: https://github.com/raspberrypi/linux/issues/1473
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/bcm2708-rpi-b-plus.dts | 10 ++++++++++
- arch/arm/boot/dts/bcm2708-rpi-b.dts | 9 +++++++++
- arch/arm/boot/dts/bcm2709-rpi-2-b.dts | 10 ++++++++++
- arch/arm/boot/dts/bcm2710-rpi-3-b.dts | 10 ++++++++++
- 4 files changed, 39 insertions(+)
-
---- a/arch/arm/boot/dts/bcm2708-rpi-b-plus.dts
-+++ b/arch/arm/boot/dts/bcm2708-rpi-b-plus.dts
-@@ -37,6 +37,11 @@
- brcm,pins = <18 19 20 21>;
- brcm,function = <4>; /* alt0 */
- };
-+
-+ audio_pins: audio_pins {
-+ brcm,pins = <40 45>;
-+ brcm,function = <4>;
-+ };
- };
-
- &sdhost {
-@@ -120,6 +125,11 @@
- hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
- };
-
-+&audio {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&audio_pins>;
-+};
-+
- / {
- __overrides__ {
- uart0 = <&uart0>,"status";
---- a/arch/arm/boot/dts/bcm2708-rpi-b.dts
-+++ b/arch/arm/boot/dts/bcm2708-rpi-b.dts
-@@ -36,6 +36,10 @@
- i2s_pins: i2s {
- brcm,pins = <28 29 30 31>;
- brcm,function = <6>; /* alt2 */
-+
-+ audio_pins: audio_pins {
-+ brcm,pins = <40 45>;
-+ brcm,function = <4>;
- };
- };
-
-@@ -114,6 +118,11 @@
- hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
- };
-
-+&audio {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&audio_pins>;
-+};
-+
- / {
- __overrides__ {
- uart0 = <&uart0>,"status";
---- a/arch/arm/boot/dts/bcm2709-rpi-2-b.dts
-+++ b/arch/arm/boot/dts/bcm2709-rpi-2-b.dts
-@@ -37,6 +37,11 @@
- brcm,pins = <18 19 20 21>;
- brcm,function = <4>; /* alt0 */
- };
-+
-+ audio_pins: audio_pins {
-+ brcm,pins = <40 45>;
-+ brcm,function = <4>;
-+ };
- };
-
- &sdhost {
-@@ -120,6 +125,11 @@
- hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
- };
-
-+&audio {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&audio_pins>;
-+};
-+
- / {
- __overrides__ {
- uart0 = <&uart0>,"status";
---- a/arch/arm/boot/dts/bcm2710-rpi-3-b.dts
-+++ b/arch/arm/boot/dts/bcm2710-rpi-3-b.dts
-@@ -61,6 +61,11 @@
- brcm,function;
- brcm,pull;
- };
-+
-+ audio_pins: audio_pins {
-+ brcm,pins = <40 41>;
-+ brcm,function = <4>;
-+ };
- };
-
- &sdhost {
-@@ -165,6 +170,11 @@
- hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
- };
-
-+&audio {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&audio_pins>;
-+};
-+
- / {
- chosen {
- bootargs = "8250.nr_uarts=1";
diff --git a/target/linux/brcm2708/patches-4.4/0424-BCM270X_DT-Restore-lost-closing-brace.patch b/target/linux/brcm2708/patches-4.4/0424-BCM270X_DT-Restore-lost-closing-brace.patch
deleted file mode 100644
index 965d32b..0000000
--- a/target/linux/brcm2708/patches-4.4/0424-BCM270X_DT-Restore-lost-closing-brace.patch
+++ /dev/null
@@ -1,20 +0,0 @@
-From 6e270c36d997a7daec9f3d87097fd5bd96df4059 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Tue, 12 Jul 2016 10:35:01 +0100
-Subject: [PATCH] BCM270X_DT: Restore lost closing brace.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/bcm2708-rpi-b.dts | 1 +
- 1 file changed, 1 insertion(+)
-
---- a/arch/arm/boot/dts/bcm2708-rpi-b.dts
-+++ b/arch/arm/boot/dts/bcm2708-rpi-b.dts
-@@ -36,6 +36,7 @@
- i2s_pins: i2s {
- brcm,pins = <28 29 30 31>;
- brcm,function = <6>; /* alt2 */
-+ };
-
- audio_pins: audio_pins {
- brcm,pins = <40 45>;
diff --git a/target/linux/brcm2708/patches-4.4/0425-config-Add-driver-for-mcp23017-I2C-GPIO-expander.patch b/target/linux/brcm2708/patches-4.4/0425-config-Add-driver-for-mcp23017-I2C-GPIO-expander.patch
deleted file mode 100644
index 5277ed5..0000000
--- a/target/linux/brcm2708/patches-4.4/0425-config-Add-driver-for-mcp23017-I2C-GPIO-expander.patch
+++ /dev/null
@@ -1,56 +0,0 @@
-From e73043d1daa80325acaa769812baa36971b06eda Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Thu, 14 Jul 2016 10:40:20 +0100
-Subject: [PATCH] config: Add driver for mcp23017 I2C GPIO expander
-
-There is already an overlay for the mcp23017 I2C GPIO expander,
-but it does nothing without the required driver module.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/configs/bcm2709_defconfig | 3 ++-
- arch/arm/configs/bcmrpi_defconfig | 3 ++-
- 2 files changed, 4 insertions(+), 2 deletions(-)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -619,6 +619,7 @@ CONFIG_GPIO_SYSFS=y
- CONFIG_GPIO_BCM_VIRT=y
- CONFIG_GPIO_ARIZONA=m
- CONFIG_GPIO_STMPE=y
-+CONFIG_GPIO_MCP23S08=m
- CONFIG_W1=m
- CONFIG_W1_MASTER_DS2490=m
- CONFIG_W1_MASTER_DS2482=m
-@@ -867,9 +868,9 @@ CONFIG_SND_BCM2708_SOC_JUSTBOOM_DIGI=m
- CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC=m
- CONFIG_SND_BCM2708_SOC_IQAUDIO_DIGI=m
- CONFIG_SND_BCM2708_SOC_RASPIDAC3=m
-+CONFIG_SND_BCM2708_SOC_ADAU1977_ADC=m
- CONFIG_SND_AUDIOINJECTOR_PI_SOUNDCARD=m
- CONFIG_SND_DIGIDAC1_SOUNDCARD=m
--CONFIG_SND_BCM2708_SOC_ADAU1977_ADC=m
- CONFIG_SND_BCM2708_SOC_DIONAUDIO_LOCO=m
- CONFIG_SND_SOC_ADAU1701=m
- CONFIG_SND_SOC_WM8804_I2C=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -611,6 +611,7 @@ CONFIG_PPS_CLIENT_GPIO=m
- CONFIG_GPIO_SYSFS=y
- CONFIG_GPIO_ARIZONA=m
- CONFIG_GPIO_STMPE=y
-+CONFIG_GPIO_MCP23S08=m
- CONFIG_W1=m
- CONFIG_W1_MASTER_DS2490=m
- CONFIG_W1_MASTER_DS2482=m
-@@ -859,9 +860,9 @@ CONFIG_SND_BCM2708_SOC_JUSTBOOM_DIGI=m
- CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC=m
- CONFIG_SND_BCM2708_SOC_IQAUDIO_DIGI=m
- CONFIG_SND_BCM2708_SOC_RASPIDAC3=m
-+CONFIG_SND_BCM2708_SOC_ADAU1977_ADC=m
- CONFIG_SND_AUDIOINJECTOR_PI_SOUNDCARD=m
- CONFIG_SND_DIGIDAC1_SOUNDCARD=m
--CONFIG_SND_BCM2708_SOC_ADAU1977_ADC=m
- CONFIG_SND_BCM2708_SOC_DIONAUDIO_LOCO=m
- CONFIG_SND_SOC_ADAU1701=m
- CONFIG_SND_SOC_WM8804_I2C=m
diff --git a/target/linux/brcm2708/patches-4.4/0426-vchiq_arm-Avoid-use-of-mutex-in-add_completion.patch b/target/linux/brcm2708/patches-4.4/0426-vchiq_arm-Avoid-use-of-mutex-in-add_completion.patch
deleted file mode 100644
index d2edccc..0000000
--- a/target/linux/brcm2708/patches-4.4/0426-vchiq_arm-Avoid-use-of-mutex-in-add_completion.patch
+++ /dev/null
@@ -1,192 +0,0 @@
-From c1aad7829f0bb4f13b6a61879361f2405eed2a9b Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 20 Jun 2016 13:51:44 +0100
-Subject: [PATCH] vchiq_arm: Avoid use of mutex in add_completion
-
-Claiming the completion_mutex within add_completion did prevent some
-messages appearing twice, but provokes a deadlock caused by vcsm using
-vchiq within a page fault handler.
-
-Revert the use of completion_mutex, and instead fix the original
-problem using more memory barriers.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- .../vc04_services/interface/vchiq_arm/vchiq_arm.c | 55 +++++++++++-----------
- .../vc04_services/interface/vchiq_arm/vchiq_core.c | 14 ++++--
- 2 files changed, 37 insertions(+), 32 deletions(-)
-
---- a/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_arm.c
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_arm.c
-@@ -64,10 +64,10 @@
- #define VCHIQ_MINOR 0
-
- /* Some per-instance constants */
--#define MAX_COMPLETIONS 16
-+#define MAX_COMPLETIONS 128
- #define MAX_SERVICES 64
- #define MAX_ELEMENTS 8
--#define MSG_QUEUE_SIZE 64
-+#define MSG_QUEUE_SIZE 128
-
- #define KEEPALIVE_VER 1
- #define KEEPALIVE_VER_MIN KEEPALIVE_VER
-@@ -208,28 +208,24 @@ add_completion(VCHIQ_INSTANCE_T instance
- void *bulk_userdata)
- {
- VCHIQ_COMPLETION_DATA_T *completion;
-+ int insert;
- DEBUG_INITIALISE(g_state.local)
-
-- mutex_lock(&instance->completion_mutex);
--
-- while (instance->completion_insert ==
-- (instance->completion_remove + MAX_COMPLETIONS)) {
-+ insert = instance->completion_insert;
-+ while ((insert - instance->completion_remove) >= MAX_COMPLETIONS) {
- /* Out of space - wait for the client */
- DEBUG_TRACE(SERVICE_CALLBACK_LINE);
- vchiq_log_trace(vchiq_arm_log_level,
- "add_completion - completion queue full");
- DEBUG_COUNT(COMPLETION_QUEUE_FULL_COUNT);
-
-- mutex_unlock(&instance->completion_mutex);
- if (down_interruptible(&instance->remove_event) != 0) {
- vchiq_log_info(vchiq_arm_log_level,
- "service_callback interrupted");
- return VCHIQ_RETRY;
- }
-
-- mutex_lock(&instance->completion_mutex);
- if (instance->closing) {
-- mutex_unlock(&instance->completion_mutex);
- vchiq_log_info(vchiq_arm_log_level,
- "service_callback closing");
- return VCHIQ_SUCCESS;
-@@ -237,9 +233,7 @@ add_completion(VCHIQ_INSTANCE_T instance
- DEBUG_TRACE(SERVICE_CALLBACK_LINE);
- }
-
-- completion =
-- &instance->completions[instance->completion_insert &
-- (MAX_COMPLETIONS - 1)];
-+ completion = &instance->completions[insert & (MAX_COMPLETIONS - 1)];
-
- completion->header = header;
- completion->reason = reason;
-@@ -260,12 +254,9 @@ add_completion(VCHIQ_INSTANCE_T instance
- wmb();
-
- if (reason == VCHIQ_MESSAGE_AVAILABLE)
-- user_service->message_available_pos =
-- instance->completion_insert;
--
-- instance->completion_insert++;
-+ user_service->message_available_pos = insert;
-
-- mutex_unlock(&instance->completion_mutex);
-+ instance->completion_insert = ++insert;
-
- up(&instance->insert_event);
-
-@@ -795,6 +786,7 @@ vchiq_ioctl(struct file *file, unsigned
- instance->completion_insert)
- && !instance->closing) {
- int rc;
-+
- DEBUG_TRACE(AWAIT_COMPLETION_LINE);
- mutex_unlock(&instance->completion_mutex);
- rc = down_interruptible(&instance->insert_event);
-@@ -809,24 +801,29 @@ vchiq_ioctl(struct file *file, unsigned
- }
- DEBUG_TRACE(AWAIT_COMPLETION_LINE);
-
-- /* A read memory barrier is needed to stop prefetch of a stale
-- ** completion record
-- */
-- rmb();
--
- if (ret == 0) {
- int msgbufcount = args.msgbufcount;
-+ int remove;
-+
-+ remove = instance->completion_remove;
-+
- for (ret = 0; ret < args.count; ret++) {
- VCHIQ_COMPLETION_DATA_T *completion;
- VCHIQ_SERVICE_T *service;
- USER_SERVICE_T *user_service;
- VCHIQ_HEADER_T *header;
-- if (instance->completion_remove ==
-- instance->completion_insert)
-+
-+ if (remove == instance->completion_insert)
- break;
-+
- completion = &instance->completions[
-- instance->completion_remove &
-- (MAX_COMPLETIONS - 1)];
-+ remove & (MAX_COMPLETIONS - 1)];
-+
-+
-+ /* A read memory barrier is needed to prevent
-+ ** the prefetch of a stale completion record
-+ */
-+ rmb();
-
- service = completion->service_userdata;
- user_service = service->base.userdata;
-@@ -903,7 +900,11 @@ vchiq_ioctl(struct file *file, unsigned
- break;
- }
-
-- instance->completion_remove++;
-+ /* Ensure that the above copy has completed
-+ ** before advancing the remove pointer. */
-+ mb();
-+
-+ instance->completion_remove = ++remove;
- }
-
- if (msgbufcount != args.msgbufcount) {
---- a/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_core.c
-+++ b/drivers/misc/vc04_services/interface/vchiq_arm/vchiq_core.c
-@@ -610,15 +610,15 @@ process_free_queue(VCHIQ_STATE_T *state)
- BITSET_T service_found[BITSET_SIZE(VCHIQ_MAX_SERVICES)];
- int slot_queue_available;
-
-- /* Use a read memory barrier to ensure that any state that may have
-- ** been modified by another thread is not masked by stale prefetched
-- ** values. */
-- rmb();
--
- /* Find slots which have been freed by the other side, and return them
- ** to the available queue. */
- slot_queue_available = state->slot_queue_available;
-
-+ /* Use a memory barrier to ensure that any state that may have been
-+ ** modified by another thread is not masked by stale prefetched
-+ ** values. */
-+ mb();
-+
- while (slot_queue_available != local->slot_queue_recycle) {
- unsigned int pos;
- int slot_index = local->slot_queue[slot_queue_available++ &
-@@ -626,6 +626,8 @@ process_free_queue(VCHIQ_STATE_T *state)
- char *data = (char *)SLOT_DATA_FROM_INDEX(state, slot_index);
- int data_found = 0;
-
-+ rmb();
-+
- vchiq_log_trace(vchiq_core_log_level, "%d: pfq %d=%x %x %x",
- state->id, slot_index, (unsigned int)data,
- local->slot_queue_recycle, slot_queue_available);
-@@ -741,6 +743,8 @@ process_free_queue(VCHIQ_STATE_T *state)
- up(&state->data_quota_event);
- }
-
-+ mb();
-+
- state->slot_queue_available = slot_queue_available;
- up(&state->slot_available_event);
- }
diff --git a/target/linux/brcm2708/patches-4.4/0427-bcm2708_fb-Default-framebuffer-to-32-bit.patch b/target/linux/brcm2708/patches-4.4/0427-bcm2708_fb-Default-framebuffer-to-32-bit.patch
deleted file mode 100644
index 76b0fd3..0000000
--- a/target/linux/brcm2708/patches-4.4/0427-bcm2708_fb-Default-framebuffer-to-32-bit.patch
+++ /dev/null
@@ -1,21 +0,0 @@
-From d2d95b8aaa0310df7270b9a87eac36030fa4ccd2 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Thu, 28 Jul 2016 12:15:47 +0100
-Subject: [PATCH] bcm2708_fb: Default framebuffer to 32-bit
-
-Can be overridden with framebuffer_depth=16 in config.txt for old behaviour
----
- drivers/video/fbdev/bcm2708_fb.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/video/fbdev/bcm2708_fb.c
-+++ b/drivers/video/fbdev/bcm2708_fb.c
-@@ -51,7 +51,7 @@ static const char *bcm2708_name = "BCM27
-
- static int fbwidth = 800; /* module parameter */
- static int fbheight = 480; /* module parameter */
--static int fbdepth = 16; /* module parameter */
-+static int fbdepth = 32; /* module parameter */
- static int fbswap = 0; /* module parameter */
-
- static u32 dma_busy_wait_threshold = 1<<15;
diff --git a/target/linux/brcm2708/patches-4.4/0428-fix-auto-sense-in-lirc_rpi-driver.patch b/target/linux/brcm2708/patches-4.4/0428-fix-auto-sense-in-lirc_rpi-driver.patch
deleted file mode 100644
index cb31c97..0000000
--- a/target/linux/brcm2708/patches-4.4/0428-fix-auto-sense-in-lirc_rpi-driver.patch
+++ /dev/null
@@ -1,45 +0,0 @@
-From f06d8bce13972d65888bd7790cf339177357f87a Mon Sep 17 00:00:00 2001
-From: Ingo Kresse <ingo.kresse at gmail.com>
-Date: Fri, 29 Jul 2016 22:50:21 +0000
-Subject: [PATCH] fix auto-sense in lirc_rpi driver
-
-On a Raspberry Pi 2, the lirc_rpi driver might receive spurious
-interrupts and change it's low-active / high-active setting.
-When this happens, the IR remote control stops working.
-
-This patch disables this auto-detection if the 'sense' parameter
-was set in the device tree, making the driver robust to such
-spurious interrupts.
----
- drivers/staging/media/lirc/lirc_rpi.c | 6 +++++-
- 1 file changed, 5 insertions(+), 1 deletion(-)
-
---- a/drivers/staging/media/lirc/lirc_rpi.c
-+++ b/drivers/staging/media/lirc/lirc_rpi.c
-@@ -79,6 +79,7 @@ static bool invert = 0;
-
- struct gpio_chip *gpiochip;
- static int irq_num;
-+static int auto_sense = 1;
-
- /* forward declarations */
- static long send_pulse(unsigned long length);
-@@ -279,7 +280,9 @@ static irqreturn_t irq_handler(int i, vo
- * detecting pulse while this
- * MUST be a space!
- */
-- sense = sense ? 0 : 1;
-+ if (auto_sense) {
-+ sense = sense ? 0 : 1;
-+ }
- }
- } else {
- data = (int) (deltv*1000000 +
-@@ -417,6 +420,7 @@ static int init_port(void)
- printk(KERN_INFO LIRC_DRIVER_NAME
- ": manually using active %s receiver on GPIO pin %d\n",
- sense ? "low" : "high", gpio_in_pin);
-+ auto_sense = 0;
- }
-
- return 0;
diff --git a/target/linux/brcm2708/patches-4.4/0429-enable-gembird-joypad-support.patch b/target/linux/brcm2708/patches-4.4/0429-enable-gembird-joypad-support.patch
deleted file mode 100644
index c760642..0000000
--- a/target/linux/brcm2708/patches-4.4/0429-enable-gembird-joypad-support.patch
+++ /dev/null
@@ -1,30 +0,0 @@
-From 582ac16712ce8b04c09f4d35015143b68637206c Mon Sep 17 00:00:00 2001
-From: Jools Wills <buzz at exotica.org.uk>
-Date: Mon, 8 Aug 2016 11:04:29 +0100
-Subject: [PATCH] enable gembird joypad support
-
----
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 2 files changed, 2 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -891,6 +891,7 @@ CONFIG_HID_EMS_FF=m
- CONFIG_HID_ELECOM=m
- CONFIG_HID_ELO=m
- CONFIG_HID_EZKEY=m
-+CONFIG_HID_GEMBIRD=m
- CONFIG_HID_HOLTEK=m
- CONFIG_HID_KEYTOUCH=m
- CONFIG_HID_KYE=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -883,6 +883,7 @@ CONFIG_HID_EMS_FF=m
- CONFIG_HID_ELECOM=m
- CONFIG_HID_ELO=m
- CONFIG_HID_EZKEY=m
-+CONFIG_HID_GEMBIRD=m
- CONFIG_HID_HOLTEK=m
- CONFIG_HID_KEYTOUCH=m
- CONFIG_HID_KYE=m
diff --git a/target/linux/brcm2708/patches-4.4/0430-Added-HiFiBerry-Digi-Pro-driver.patch b/target/linux/brcm2708/patches-4.4/0430-Added-HiFiBerry-Digi-Pro-driver.patch
deleted file mode 100644
index e2dafd2..0000000
--- a/target/linux/brcm2708/patches-4.4/0430-Added-HiFiBerry-Digi-Pro-driver.patch
+++ /dev/null
@@ -1,187 +0,0 @@
-From ca5dc61992ac0451a3d778fd760fbcd565271a66 Mon Sep 17 00:00:00 2001
-From: "Daniel Matuschek (HiFiBerry)" <daniel at hifiberry.com>
-Date: Tue, 26 Jul 2016 19:16:25 +0200
-Subject: [PATCH] Added HiFiBerry Digi+ Pro driver
-
-Signed-off-by: Daniel Matuschek <daniel at hifiberry.com>
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 8 +++-
- .../dts/overlays/hifiberry-digi-pro-overlay.dts | 41 +++++++++++++++++
- sound/soc/bcm/hifiberry_digi.c | 51 ++++++++++++++++++++++
- 4 files changed, 100 insertions(+), 1 deletion(-)
- create mode 100644 arch/arm/boot/dts/overlays/hifiberry-digi-pro-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -31,6 +31,7 @@ dtbo-$(RPI_DT_OVERLAYS) += hifiberry-amp
- dtbo-$(RPI_DT_OVERLAYS) += hifiberry-dac.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += hifiberry-dacplus.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += hifiberry-digi.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += hifiberry-digi-pro.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += hy28a.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += hy28b.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c-gpio.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -377,11 +377,17 @@ Params: 24db_digital_gain Allow ga
-
-
- Name: hifiberry-digi
--Info: Configures the HifiBerry Digi audio card
-+Info: Configures the HifiBerry Digi and Digi+ audio card
- Load: dtoverlay=hifiberry-digi
- Params: <None>
-
-
-+Name: hifiberry-digi-pro
-+Info: Configures the HifiBerry Digi+ Pro audio card
-+Load: dtoverlay=hifiberry-digi-pro
-+Params: <None>
-+
-+
- Name: hy28a
- Info: HY28A - 2.8" TFT LCD Display Module by HAOYU Electronics
- Default values match Texy's display shield
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/hifiberry-digi-pro-overlay.dts
-@@ -0,0 +1,41 @@
-+// Definitions for HiFiBerry Digi Pro
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&i2s>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&i2c1>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ wm8804 at 3b {
-+ #sound-dai-cells = <0>;
-+ compatible = "wlf,wm8804";
-+ reg = <0x3b>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&sound>;
-+ __overlay__ {
-+ compatible = "hifiberry,hifiberry-digi";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ clock44-gpio = <&gpio 5 0>;
-+ clock48-gpio = <&gpio 6 0>;
-+ };
-+ };
-+};
---- a/sound/soc/bcm/hifiberry_digi.c
-+++ b/sound/soc/bcm/hifiberry_digi.c
-@@ -23,6 +23,7 @@
- #include <sound/pcm_params.h>
- #include <sound/soc.h>
- #include <sound/jack.h>
-+#include <linux/gpio/consumer.h>
-
- #include "../codecs/wm8804.h"
-
-@@ -30,9 +31,34 @@ static short int auto_shutdown_output =
- module_param(auto_shutdown_output, short, S_IRUSR | S_IWUSR | S_IRGRP | S_IWGRP);
- MODULE_PARM_DESC(auto_shutdown_output, "Shutdown SP/DIF output if playback is stopped");
-
-+#define CLK_44EN_RATE 22579200UL
-+#define CLK_48EN_RATE 24576000UL
-+
-+static bool snd_rpi_hifiberry_is_digipro;
-+static struct gpio_desc *snd_rpi_hifiberry_clk44gpio;
-+static struct gpio_desc *snd_rpi_hifiberry_clk48gpio;
-
- static int samplerate=44100;
-
-+static uint32_t snd_rpi_hifiberry_digi_enable_clock(int sample_rate)
-+{
-+ switch (sample_rate) {
-+ case 11025:
-+ case 22050:
-+ case 44100:
-+ case 88200:
-+ case 176400:
-+ gpiod_set_value_cansleep(snd_rpi_hifiberry_clk44gpio, 1);
-+ gpiod_set_value_cansleep(snd_rpi_hifiberry_clk48gpio, 0);
-+ return CLK_44EN_RATE;
-+ default:
-+ gpiod_set_value_cansleep(snd_rpi_hifiberry_clk48gpio, 1);
-+ gpiod_set_value_cansleep(snd_rpi_hifiberry_clk44gpio, 0);
-+ return CLK_48EN_RATE;
-+ }
-+}
-+
-+
- static int snd_rpi_hifiberry_digi_init(struct snd_soc_pcm_runtime *rtd)
- {
- struct snd_soc_codec *codec = rtd->codec;
-@@ -40,6 +66,14 @@ static int snd_rpi_hifiberry_digi_init(s
- /* enable TX output */
- snd_soc_update_bits(codec, WM8804_PWRDN, 0x4, 0x0);
-
-+ /* Initialize Digi+ Pro hardware */
-+ if (snd_rpi_hifiberry_is_digipro) {
-+ struct snd_soc_dai_link *dai = rtd->dai_link;
-+
-+ dai->name = "HiFiBerry Digi+ Pro";
-+ dai->stream_name = "HiFiBerry Digi+ Pro HiFi";
-+ }
-+
- return 0;
- }
-
-@@ -87,6 +121,9 @@ static int snd_rpi_hifiberry_digi_hw_par
- mclk_freq=samplerate*128;
- mclk_div=WM8804_MCLKDIV_128FS;
- }
-+
-+ if (snd_rpi_hifiberry_is_digipro)
-+ sysclk = snd_rpi_hifiberry_digi_enable_clock(samplerate);
-
- switch (samplerate) {
- case 32000:
-@@ -121,6 +158,7 @@ static int snd_rpi_hifiberry_digi_hw_par
-
- ret = snd_soc_dai_set_sysclk(codec_dai, WM8804_TX_CLKSRC_PLL,
- sysclk, SND_SOC_CLOCK_OUT);
-+
- if (ret < 0) {
- dev_err(codec->dev,
- "Failed to set WM8804 SYSCLK: %d\n", ret);
-@@ -187,6 +225,19 @@ static int snd_rpi_hifiberry_digi_probe(
- dai->platform_name = NULL;
- dai->platform_of_node = i2s_node;
- }
-+
-+ snd_rpi_hifiberry_is_digipro = 1;
-+
-+ snd_rpi_hifiberry_clk44gpio =
-+ devm_gpiod_get(&pdev->dev, "clock44", GPIOD_OUT_LOW);
-+ if (IS_ERR(snd_rpi_hifiberry_clk44gpio))
-+ snd_rpi_hifiberry_is_digipro = 0;
-+
-+ snd_rpi_hifiberry_clk48gpio =
-+ devm_gpiod_get(&pdev->dev, "clock48", GPIOD_OUT_LOW);
-+ if (IS_ERR(snd_rpi_hifiberry_clk48gpio))
-+ snd_rpi_hifiberry_is_digipro = 0;
-+
- }
-
- ret = snd_soc_register_card(&snd_rpi_hifiberry_digi);
diff --git a/target/linux/brcm2708/patches-4.4/0431-clk-bcm2835-Mark-the-CM-SDRAM-clock-s-parent-as-crit.patch b/target/linux/brcm2708/patches-4.4/0431-clk-bcm2835-Mark-the-CM-SDRAM-clock-s-parent-as-crit.patch
deleted file mode 100644
index e3c7f5a..0000000
--- a/target/linux/brcm2708/patches-4.4/0431-clk-bcm2835-Mark-the-CM-SDRAM-clock-s-parent-as-crit.patch
+++ /dev/null
@@ -1,73 +0,0 @@
-From f863897ded282644de97eb600ccb596b7d58abab Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Wed, 1 Jun 2016 12:05:35 -0700
-Subject: [PATCH] clk: bcm2835: Mark the CM SDRAM clock's parent as critical
-
-While the SDRAM is being driven by its dedicated PLL most of the time,
-there is a little loop running in the firmware that periodically turns
-on the CM SDRAM clock (using its pre-initialized parent) and switches
-SDRAM to using the CM clock to do PVT recalibration.
-
-This avoids system hangs if we choose SDRAM's parent for some other
-clock, then disable that clock.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/clk/bcm/clk-bcm2835.c | 25 +++++++++++++++++++++++++
- 1 file changed, 25 insertions(+)
-
---- a/drivers/clk/bcm/clk-bcm2835.c
-+++ b/drivers/clk/bcm/clk-bcm2835.c
-@@ -36,6 +36,7 @@
-
- #include <linux/clk-provider.h>
- #include <linux/clkdev.h>
-+#include <linux/clk.h>
- #include <linux/clk/bcm2835.h>
- #include <linux/debugfs.h>
- #include <linux/module.h>
-@@ -1841,6 +1842,25 @@ static const struct bcm2835_clk_desc clk
- .ctl_reg = CM_PERIICTL),
- };
-
-+/*
-+ * Permanently take a reference on the parent of the SDRAM clock.
-+ *
-+ * While the SDRAM is being driven by its dedicated PLL most of the
-+ * time, there is a little loop running in the firmware that
-+ * periodically switches the SDRAM to using our CM clock to do PVT
-+ * recalibration, with the assumption that the previously configured
-+ * SDRAM parent is still enabled and running.
-+ */
-+static int bcm2835_mark_sdc_parent_critical(struct clk *sdc)
-+{
-+ struct clk *parent = clk_get_parent(sdc);
-+
-+ if (IS_ERR(parent))
-+ return PTR_ERR(parent);
-+
-+ return clk_prepare_enable(parent);
-+}
-+
- static int bcm2835_clk_probe(struct platform_device *pdev)
- {
- struct device *dev = &pdev->dev;
-@@ -1850,6 +1870,7 @@ static int bcm2835_clk_probe(struct plat
- const struct bcm2835_clk_desc *desc;
- const size_t asize = ARRAY_SIZE(clk_desc_array);
- size_t i;
-+ int ret;
-
- cprman = devm_kzalloc(dev,
- sizeof(*cprman) + asize * sizeof(*clks),
-@@ -1880,6 +1901,10 @@ static int bcm2835_clk_probe(struct plat
- clks[i] = desc->clk_register(cprman, desc->data);
- }
-
-+ ret = bcm2835_mark_sdc_parent_critical(clks[BCM2835_CLOCK_SDRAM]);
-+ if (ret)
-+ return ret;
-+
- return of_clk_add_provider(dev->of_node, of_clk_src_onecell_get,
- &cprman->onecell);
- }
diff --git a/target/linux/brcm2708/patches-4.4/0432-clk-bcm2835-Don-t-rate-change-PLLs-on-behalf-of-divi.patch b/target/linux/brcm2708/patches-4.4/0432-clk-bcm2835-Don-t-rate-change-PLLs-on-behalf-of-divi.patch
deleted file mode 100644
index 0c14316..0000000
--- a/target/linux/brcm2708/patches-4.4/0432-clk-bcm2835-Don-t-rate-change-PLLs-on-behalf-of-divi.patch
+++ /dev/null
@@ -1,27 +0,0 @@
-From dc6b6175531fd8c2d7831569eefd7acb0c54d016 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Thu, 31 Mar 2016 12:51:04 -0700
-Subject: [PATCH] clk: bcm2835: Don't rate change PLLs on behalf of dividers.
-
-Our core PLLs are intended to be configured once and left alone. With
-the flag set, asking to set the PLLD_DSI1 clock rate would change PLLD
-just to get closer to the requested DSI clock, thus changing PLLD_PER,
-the UART and ethernet PHY clock rates downstream of it, and breaking
-ethernet.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/clk/bcm/clk-bcm2835.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/clk/bcm/clk-bcm2835.c
-+++ b/drivers/clk/bcm/clk-bcm2835.c
-@@ -1211,7 +1211,7 @@ bcm2835_register_pll_divider(struct bcm2
- init.num_parents = 1;
- init.name = divider_name;
- init.ops = &bcm2835_pll_divider_clk_ops;
-- init.flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED;
-+ init.flags = CLK_IGNORE_UNUSED;
-
- divider = devm_kzalloc(cprman->dev, sizeof(*divider), GFP_KERNEL);
- if (!divider)
diff --git a/target/linux/brcm2708/patches-4.4/0433-clk-bcm2835-Do-appropriate-name-lookups-for-DSI1-s-p.patch b/target/linux/brcm2708/patches-4.4/0433-clk-bcm2835-Do-appropriate-name-lookups-for-DSI1-s-p.patch
deleted file mode 100644
index 4823bf8..0000000
--- a/target/linux/brcm2708/patches-4.4/0433-clk-bcm2835-Do-appropriate-name-lookups-for-DSI1-s-p.patch
+++ /dev/null
@@ -1,125 +0,0 @@
-From 9c7608ef6a1cdcc91462be7f48de0bdfc25dd247 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Thu, 14 Apr 2016 15:13:53 -0700
-Subject: [PATCH] clk: bcm2835: Do appropriate name lookups for DSI1's parents
- as well.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- .../bindings/clock/brcm,bcm2835-cprman.txt | 12 ++++-
- drivers/clk/bcm/clk-bcm2835.c | 54 +++++++++++++++++-----
- 2 files changed, 54 insertions(+), 12 deletions(-)
-
---- a/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt
-+++ b/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt
-@@ -16,7 +16,17 @@ Required properties:
- - #clock-cells: Should be <1>. The permitted clock-specifier values can be
- found in include/dt-bindings/clock/bcm2835.h
- - reg: Specifies base physical address and size of the registers
--- clocks: The external oscillator clock phandle
-+- clocks: phandles to the parent clocks used as input to the module, in
-+ the following order:
-+
-+ - External oscillator
-+ - DSI1 byte clock
-+ - DSI1 DDR2 clock
-+ - DSI1 DDR clock
-+
-+ Only external oscillator is required. The DSI clocks may
-+ not be present, in which case their children will be
-+ unusable.
-
- Example:
-
---- a/drivers/clk/bcm/clk-bcm2835.c
-+++ b/drivers/clk/bcm/clk-bcm2835.c
-@@ -297,11 +297,29 @@
- #define LOCK_TIMEOUT_NS 100000000
- #define BCM2835_MAX_FB_RATE 1750000000u
-
-+/*
-+ * Names of clocks used within the driver that need to be replaced
-+ * with an external parent's name. This array is in the order that
-+ * the clocks node in the DT references external clocks.
-+ */
-+static const char *cprman_parent_names[] = {
-+ "xosc",
-+ "dsi1_byte",
-+ "dsi1_ddr2",
-+ "dsi1_ddr",
-+};
-+
- struct bcm2835_cprman {
- struct device *dev;
- void __iomem *regs;
- spinlock_t regs_lock; /* spinlock for all clocks */
-- const char *osc_name;
-+
-+ /*
-+ * Real names of cprman clock parents looked up through
-+ * of_clk_get_parent_name(), which will be used in the
-+ * parent_names[] arrays for clock registration.
-+ */
-+ const char *real_parent_names[ARRAY_SIZE(cprman_parent_names)];
-
- struct clk_onecell_data onecell;
- struct clk *clks[];
-@@ -1170,7 +1188,7 @@ static struct clk *bcm2835_register_pll(
- memset(&init, 0, sizeof(init));
-
- /* All of the PLLs derive from the external oscillator. */
-- init.parent_names = &cprman->osc_name;
-+ init.parent_names = &cprman->real_parent_names[0];
- init.num_parents = 1;
- init.name = data->name;
- init.ops = &bcm2835_pll_clk_ops;
-@@ -1253,17 +1271,21 @@ static struct clk *bcm2835_register_cloc
- struct bcm2835_clock *clock;
- struct clk_init_data init;
- const char *parents[1 << CM_SRC_BITS];
-- size_t i;
-+ size_t i, j;
-
- /*
-- * Replace our "xosc" references with the oscillator's
-- * actual name.
-+ * Replace our strings referencing parent clocks with the
-+ * actual clock-output-name of the parent.
- */
- for (i = 0; i < data->num_mux_parents; i++) {
-- if (strcmp(data->parents[i], "xosc") == 0)
-- parents[i] = cprman->osc_name;
-- else
-- parents[i] = data->parents[i];
-+ parents[i] = data->parents[i];
-+
-+ for (j = 0; j < ARRAY_SIZE(cprman_parent_names); j++) {
-+ if (strcmp(parents[i], cprman_parent_names[j]) == 0) {
-+ parents[i] = cprman->real_parent_names[j];
-+ break;
-+ }
-+ }
- }
-
- memset(&init, 0, sizeof(init));
-@@ -1885,8 +1907,18 @@ static int bcm2835_clk_probe(struct plat
- if (IS_ERR(cprman->regs))
- return PTR_ERR(cprman->regs);
-
-- cprman->osc_name = of_clk_get_parent_name(dev->of_node, 0);
-- if (!cprman->osc_name)
-+ for (i = 0; i < ARRAY_SIZE(cprman_parent_names); i++) {
-+ cprman->real_parent_names[i] =
-+ of_clk_get_parent_name(dev->of_node, i);
-+ }
-+ /*
-+ * Make sure the external oscillator has been registered.
-+ *
-+ * The other (DSI) clocks are not present on older device
-+ * trees, which we still need to support for backwards
-+ * compatibility.
-+ */
-+ if (!cprman->real_parent_names[0])
- return -ENODEV;
-
- platform_set_drvdata(pdev, cprman);
diff --git a/target/linux/brcm2708/patches-4.4/0434-clk-bcm2835-Add-an-enum-for-the-DSI1-pixel-clock.patch b/target/linux/brcm2708/patches-4.4/0434-clk-bcm2835-Add-an-enum-for-the-DSI1-pixel-clock.patch
deleted file mode 100644
index a8a6dd7..0000000
--- a/target/linux/brcm2708/patches-4.4/0434-clk-bcm2835-Add-an-enum-for-the-DSI1-pixel-clock.patch
+++ /dev/null
@@ -1,87 +0,0 @@
-From 05647aae00756fe9ef796af5ea7c712da58b658c Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Thu, 14 Apr 2016 19:00:33 -0700
-Subject: [PATCH] clk: bcm2835: Add an enum for the DSI1 pixel clock.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/clk/bcm/clk-bcm2835.c | 39 +++++++++++++++++++++++++++++++++++--
- include/dt-bindings/clock/bcm2835.h | 1 +
- 2 files changed, 38 insertions(+), 2 deletions(-)
-
---- a/drivers/clk/bcm/clk-bcm2835.c
-+++ b/drivers/clk/bcm/clk-bcm2835.c
-@@ -936,6 +936,9 @@ static long bcm2835_clock_rate_from_divi
- const struct bcm2835_clock_data *data = clock->data;
- u64 temp;
-
-+ if (data->int_bits == 0 && data->frac_bits == 0)
-+ return parent_rate;
-+
- /*
- * The divisor is a 12.12 fixed point field, but only some of
- * the bits are populated in any given clock.
-@@ -959,7 +962,12 @@ static unsigned long bcm2835_clock_get_r
- struct bcm2835_clock *clock = bcm2835_clock_from_hw(hw);
- struct bcm2835_cprman *cprman = clock->cprman;
- const struct bcm2835_clock_data *data = clock->data;
-- u32 div = cprman_read(cprman, data->div_reg);
-+ u32 div;
-+
-+ if (data->int_bits == 0 && data->frac_bits == 0)
-+ return parent_rate;
-+
-+ div = cprman_read(cprman, data->div_reg);
-
- return bcm2835_clock_rate_from_divisor(clock, parent_rate, div);
- }
-@@ -1405,6 +1413,28 @@ static const char *const bcm2835_clock_v
- __VA_ARGS__)
-
- /*
-+ * DSI1 parent clocks. The DSI1 byte clock comes from the DSI1 PHY,
-+ * which in turn sources from plld_dsi1.
-+ */
-+static const char *const bcm2835_clock_dsi1_parents[] = {
-+ "gnd",
-+ "xosc",
-+ "testdebug0",
-+ "testdebug1",
-+ "dsi1_ddr",
-+ "dsi1_ddr_inv",
-+ "dsi1_ddr2",
-+ "dsi1_ddr2_inv",
-+ "dsi1_byte",
-+ "dsi1_byte_inv",
-+};
-+
-+#define REGISTER_DSI1_CLK(...) REGISTER_CLK( \
-+ .num_mux_parents = ARRAY_SIZE(bcm2835_clock_dsi1_parents), \
-+ .parents = bcm2835_clock_dsi1_parents, \
-+ __VA_ARGS__)
-+
-+/*
- * the real definition of all the pll, pll_dividers and clocks
- * these make use of the above REGISTER_* macros
- */
-@@ -1849,7 +1879,12 @@ static const struct bcm2835_clk_desc clk
- .div_reg = CM_DSI1EDIV,
- .int_bits = 4,
- .frac_bits = 8),
--
-+ [BCM2835_CLOCK_DSI1P] = REGISTER_DSI1_CLK(
-+ .name = "dsi1p",
-+ .ctl_reg = CM_DSI1PCTL,
-+ .div_reg = CM_DSI1PDIV,
-+ .int_bits = 0,
-+ .frac_bits = 0),
- /* the gates */
-
- /*
---- a/include/dt-bindings/clock/bcm2835.h
-+++ b/include/dt-bindings/clock/bcm2835.h
-@@ -64,3 +64,4 @@
- #define BCM2835_CLOCK_CAM1 46
- #define BCM2835_CLOCK_DSI0E 47
- #define BCM2835_CLOCK_DSI1E 48
-+#define BCM2835_CLOCK_DSI1P 49
diff --git a/target/linux/brcm2708/patches-4.4/0435-drm-fb_cma_helper-Remove-implicit-call-to-disable_un.patch b/target/linux/brcm2708/patches-4.4/0435-drm-fb_cma_helper-Remove-implicit-call-to-disable_un.patch
deleted file mode 100644
index 70e21d8..0000000
--- a/target/linux/brcm2708/patches-4.4/0435-drm-fb_cma_helper-Remove-implicit-call-to-disable_un.patch
+++ /dev/null
@@ -1,79 +0,0 @@
-From 5276a04f7ccf15158ec5b71273d278b0a859beaf Mon Sep 17 00:00:00 2001
-From: Maxime Ripard <maxime.ripard at free-electrons.com>
-Date: Thu, 14 Jan 2016 16:24:56 +0100
-Subject: [PATCH] drm/fb_cma_helper: Remove implicit call to
- disable_unused_functions
-
-The drm_fbdev_cma_init function always calls the
-drm_helper_disable_unused_functions. Since it's part of the usual probe
-process, all the drivers using that helper will end up having their encoder
-and CRTC disable functions called at probe if their device has not been
-reported as enabled.
-
-This could be fixed by reading out from the registers the current state of
-the device if it is enabled, but even that will not handle the case where
-the device is actually disabled.
-
-Moreover, the drivers using the atomic modesetting expect that their enable
-and disable callback to be called when the device is already enabled or
-disabled (respectively).
-
-We can however fix this issue by moving the call to
-drm_helper_disable_unused_functions out of drm_fbdev_cma_init and make the
-drivers needing it (all the drivers calling drm_fbdev_cma_init and not
-using the atomic modesetting) explicitly call it.
-
-Signed-off-by: Maxime Ripard <maxime.ripard at free-electrons.com>
-Link: http://patchwork.freedesktop.org/patch/msgid/1452785109-6172-14-git-send-email-maxime.ripard@free-electrons.com
-Acked-by: Laurent Pinchart <laurent.pinchart at ideasonboard.com>
-Signed-off-by: Daniel Vetter <daniel.vetter at ffwll.ch>
-(cherry picked from commit 4314e19ef4ae0ba8872bd8610f6fef5e8743e236)
----
- drivers/gpu/drm/drm_fb_cma_helper.c | 3 ---
- drivers/gpu/drm/imx/imx-drm-core.c | 1 +
- drivers/gpu/drm/sti/sti_drv.c | 1 +
- drivers/gpu/drm/tilcdc/tilcdc_drv.c | 1 +
- 4 files changed, 3 insertions(+), 3 deletions(-)
-
---- a/drivers/gpu/drm/drm_fb_cma_helper.c
-+++ b/drivers/gpu/drm/drm_fb_cma_helper.c
-@@ -348,9 +348,6 @@ struct drm_fbdev_cma *drm_fbdev_cma_init
-
- }
-
-- /* disable all the possible outputs/crtcs before entering KMS mode */
-- drm_helper_disable_unused_functions(dev);
--
- ret = drm_fb_helper_initial_config(helper, preferred_bpp);
- if (ret < 0) {
- dev_err(dev->dev, "Failed to set initial hw configuration.\n");
---- a/drivers/gpu/drm/imx/imx-drm-core.c
-+++ b/drivers/gpu/drm/imx/imx-drm-core.c
-@@ -313,6 +313,7 @@ static int imx_drm_driver_load(struct dr
- dev_warn(drm->dev, "Invalid legacyfb_depth. Defaulting to 16bpp\n");
- legacyfb_depth = 16;
- }
-+ drm_helper_disable_unused_functions(drm);
- imxdrm->fbhelper = drm_fbdev_cma_init(drm, legacyfb_depth,
- drm->mode_config.num_crtc, MAX_CRTC);
- if (IS_ERR(imxdrm->fbhelper)) {
---- a/drivers/gpu/drm/sti/sti_drv.c
-+++ b/drivers/gpu/drm/sti/sti_drv.c
-@@ -160,6 +160,7 @@ static int sti_load(struct drm_device *d
-
- drm_mode_config_reset(dev);
-
-+ drm_helper_disable_unused_functions(dev);
- drm_fbdev_cma_init(dev, 32,
- dev->mode_config.num_crtc,
- dev->mode_config.num_connector);
---- a/drivers/gpu/drm/tilcdc/tilcdc_drv.c
-+++ b/drivers/gpu/drm/tilcdc/tilcdc_drv.c
-@@ -294,6 +294,7 @@ static int tilcdc_load(struct drm_device
- break;
- }
-
-+ drm_helper_disable_unused_functions(dev);
- priv->fbdev = drm_fbdev_cma_init(dev, bpp,
- dev->mode_config.num_crtc,
- dev->mode_config.num_connector);
diff --git a/target/linux/brcm2708/patches-4.4/0436-overlays-Add-assert_falling_edge-to-pps-gpio-overlay.patch b/target/linux/brcm2708/patches-4.4/0436-overlays-Add-assert_falling_edge-to-pps-gpio-overlay.patch
deleted file mode 100644
index bb6e6de..0000000
--- a/target/linux/brcm2708/patches-4.4/0436-overlays-Add-assert_falling_edge-to-pps-gpio-overlay.patch
+++ /dev/null
@@ -1,31 +0,0 @@
-From 801e6433bb229f2d00caf2607a8b41d60596cc4c Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Tue, 9 Aug 2016 21:51:41 +0100
-Subject: [PATCH] overlays: Add assert_falling_edge to pps-gpio overlay
-
-See: https://github.com/raspberrypi/linux/issues/1590
----
- arch/arm/boot/dts/overlays/README | 2 ++
- arch/arm/boot/dts/overlays/pps-gpio-overlay.dts | 1 +
- 2 files changed, 3 insertions(+)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -797,6 +797,8 @@ Name: pps-gpio
- Info: Configures the pps-gpio (pulse-per-second time signal via GPIO).
- Load: dtoverlay=pps-gpio,<param>=<val>
- Params: gpiopin Input GPIO (default "18")
-+ assert_falling_edge When present, assert is indicated by a falling
-+ edge, rather than by a rising edge
-
-
- Name: pwm
---- a/arch/arm/boot/dts/overlays/pps-gpio-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/pps-gpio-overlay.dts
-@@ -30,5 +30,6 @@
- __overrides__ {
- gpiopin = <&pps>,"gpios:4",
- <&pps_pins>,"brcm,pins:0";
-+ assert_falling_edge = <&pps>,"assert-falling-edge?";
- };
- };
diff --git a/target/linux/brcm2708/patches-4.4/0437-drm-mipi-dsi-Unregister-bus-at-exit.patch b/target/linux/brcm2708/patches-4.4/0437-drm-mipi-dsi-Unregister-bus-at-exit.patch
deleted file mode 100644
index 7088419..0000000
--- a/target/linux/brcm2708/patches-4.4/0437-drm-mipi-dsi-Unregister-bus-at-exit.patch
+++ /dev/null
@@ -1,30 +0,0 @@
-From 2f9d800b5fc37f5574be96db7ab468c523790826 Mon Sep 17 00:00:00 2001
-From: Takashi Iwai <tiwai at suse.de>
-Date: Tue, 2 Aug 2016 14:16:42 +0200
-Subject: [PATCH] drm/mipi-dsi: Unregister bus at exit
-
-This is a preliminary patch for building drm-mipi-dsi as a module.
-Add the module exit callback to unregister the bus properly.
-
-Suggested-by: Thierry Reding <treding at nvidia.com>
-Signed-off-by: Takashi Iwai <tiwai at suse.de>
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/drm_mipi_dsi.c | 6 ++++++
- 1 file changed, 6 insertions(+)
-
---- a/drivers/gpu/drm/drm_mipi_dsi.c
-+++ b/drivers/gpu/drm/drm_mipi_dsi.c
-@@ -928,6 +928,12 @@ static int __init mipi_dsi_bus_init(void
- }
- postcore_initcall(mipi_dsi_bus_init);
-
-+static void __exit mipi_dsi_bus_exit(void)
-+{
-+ bus_unregister(&mipi_dsi_bus_type);
-+}
-+module_exit(mipi_dsi_bus_exit);
-+
- MODULE_AUTHOR("Andrzej Hajda <a.hajda at samsung.com>");
- MODULE_DESCRIPTION("MIPI DSI Bus");
- MODULE_LICENSE("GPL and additional rights");
diff --git a/target/linux/brcm2708/patches-4.4/0438-drm-mipi-dsi-Allow-to-build-drm-mipi-dsi-as-a-module.patch b/target/linux/brcm2708/patches-4.4/0438-drm-mipi-dsi-Allow-to-build-drm-mipi-dsi-as-a-module.patch
deleted file mode 100644
index 5f6822a..0000000
--- a/target/linux/brcm2708/patches-4.4/0438-drm-mipi-dsi-Allow-to-build-drm-mipi-dsi-as-a-module.patch
+++ /dev/null
@@ -1,32 +0,0 @@
-From 9d2d8cfdce5e946ef9134f53ae9871919d8e756c Mon Sep 17 00:00:00 2001
-From: Takashi Iwai <tiwai at suse.de>
-Date: Tue, 2 Aug 2016 14:16:43 +0200
-Subject: [PATCH] drm/mipi-dsi: Allow to build drm-mipi-dsi as a module
-
-The drm-mipi-dsi driver has been only built-in although this isn't
-strictly required to be so. Since it's referred by lots of DRM
-drivers nowadays, most of distro kernels include the driver as
-built-in as a result, even though many systems don't need it at all.
-
-This patch fixes Kconfig to allow drm-mipi-dsi driver built as a
-module, so that we can save footprint on systems without such DRM
-drivers. The probe order is managed by the module dependency, and
-postcore_initcall() works just fine as a module init call.
-
-Signed-off-by: Takashi Iwai <tiwai at suse.de>
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/Kconfig | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/gpu/drm/Kconfig
-+++ b/drivers/gpu/drm/Kconfig
-@@ -22,7 +22,7 @@ menuconfig DRM
- (/dev/agpgart) support if it is available for your platform.
-
- config DRM_MIPI_DSI
-- bool
-+ tristate
- depends on DRM
-
- config DRM_KMS_HELPER
diff --git a/target/linux/brcm2708/patches-4.4/0439-drm-vc4-Fix-flipped-HVS-channels-for-DSI0-1.patch b/target/linux/brcm2708/patches-4.4/0439-drm-vc4-Fix-flipped-HVS-channels-for-DSI0-1.patch
deleted file mode 100644
index fea2e89..0000000
--- a/target/linux/brcm2708/patches-4.4/0439-drm-vc4-Fix-flipped-HVS-channels-for-DSI0-1.patch
+++ /dev/null
@@ -1,30 +0,0 @@
-From ab31298089f141d61d8b91a037aa69b8ca398142 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Thu, 11 Feb 2016 12:29:45 -0800
-Subject: [PATCH] drm/vc4: Fix flipped HVS channels for DSI0/1.
-
-Empirically, DSI1 appears to be using HVS channel 0 on my Pi2.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_crtc.c | 4 ++--
- 1 file changed, 2 insertions(+), 2 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_crtc.c
-+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
-@@ -699,13 +699,13 @@ void vc4_cancel_page_flip(struct drm_crt
- }
-
- static const struct vc4_crtc_data pv0_data = {
-- .hvs_channel = 0,
-+ .hvs_channel = 2,
- .encoder0_type = VC4_ENCODER_TYPE_DSI0,
- .encoder1_type = VC4_ENCODER_TYPE_DPI,
- };
-
- static const struct vc4_crtc_data pv1_data = {
-- .hvs_channel = 2,
-+ .hvs_channel = 0,
- .encoder0_type = VC4_ENCODER_TYPE_DSI1,
- .encoder1_type = VC4_ENCODER_TYPE_SMI,
- };
diff --git a/target/linux/brcm2708/patches-4.4/0440-drm-vc4-Add-support-for-feeding-DSI-encoders-from-th.patch b/target/linux/brcm2708/patches-4.4/0440-drm-vc4-Add-support-for-feeding-DSI-encoders-from-th.patch
deleted file mode 100644
index 4e27f8a..0000000
--- a/target/linux/brcm2708/patches-4.4/0440-drm-vc4-Add-support-for-feeding-DSI-encoders-from-th.patch
+++ /dev/null
@@ -1,96 +0,0 @@
-From 34d4366b33a39d0b563d0d3c44edb80ca9348f12 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Wed, 10 Feb 2016 16:17:29 -0800
-Subject: [PATCH] drm/vc4: Add support for feeding DSI encoders from the pixel
- valve.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_crtc.c | 30 +++++++++++++++++-------------
- drivers/gpu/drm/vc4/vc4_regs.h | 2 ++
- 2 files changed, 19 insertions(+), 13 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_crtc.c
-+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
-@@ -210,38 +210,40 @@ static u32 vc4_get_fifo_full_level(u32 f
- }
-
- /*
-- * Returns the clock select bit for the connector attached to the
-- * CRTC.
-+ * Returns the encoder attached to the CRTC.
-+ *
-+ * VC4 can only scan out to one encoder at a type, while the DRM core
-+ * allows drivers to push pixels to more than one encoder from the
-+ * same CRTC.
- */
--static int vc4_get_clock_select(struct drm_crtc *crtc)
-+static struct drm_encoder *vc4_get_crtc_encoder(struct drm_crtc *crtc)
- {
- struct drm_connector *connector;
-
- drm_for_each_connector(connector, crtc->dev) {
- if (connector->state->crtc == crtc) {
-- struct drm_encoder *encoder = connector->encoder;
-- struct vc4_encoder *vc4_encoder =
-- to_vc4_encoder(encoder);
--
-- return vc4_encoder->clock_select;
-+ return connector->encoder;
- }
- }
-
-- return -1;
-+ return NULL;
- }
-
- static void vc4_crtc_mode_set_nofb(struct drm_crtc *crtc)
- {
- struct drm_device *dev = crtc->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ struct drm_encoder *encoder = vc4_get_crtc_encoder(crtc);
-+ struct vc4_encoder *vc4_encoder = to_vc4_encoder(encoder);
- struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
- struct drm_crtc_state *state = crtc->state;
- struct drm_display_mode *mode = &state->adjusted_mode;
- bool interlace = mode->flags & DRM_MODE_FLAG_INTERLACE;
- u32 vactive = (mode->vdisplay >> (interlace ? 1 : 0));
-- u32 format = PV_CONTROL_FORMAT_24;
-- bool debug_dump_regs = false;
-- int clock_select = vc4_get_clock_select(crtc);
-+ bool is_dsi = (vc4_encoder->type == VC4_ENCODER_TYPE_DSI0 ||
-+ vc4_encoder->type == VC4_ENCODER_TYPE_DSI1);
-+ u32 format = is_dsi ? PV_CONTROL_FORMAT_DSIV_24 : PV_CONTROL_FORMAT_24;
-+ bool debug_dump_regs = true;
-
- if (debug_dump_regs) {
- DRM_INFO("CRTC %d regs before:\n", drm_crtc_index(crtc));
-@@ -289,6 +291,7 @@ static void vc4_crtc_mode_set_nofb(struc
-
- CRTC_WRITE(PV_V_CONTROL,
- PV_VCONTROL_CONTINUOUS |
-+ (is_dsi ? PV_VCONTROL_DSI : 0) |
- (interlace ? PV_VCONTROL_INTERLACE : 0));
-
- CRTC_WRITE(PV_CONTROL,
-@@ -298,7 +301,8 @@ static void vc4_crtc_mode_set_nofb(struc
- PV_CONTROL_CLR_AT_START |
- PV_CONTROL_TRIGGER_UNDERFLOW |
- PV_CONTROL_WAIT_HSTART |
-- VC4_SET_FIELD(clock_select, PV_CONTROL_CLK_SELECT) |
-+ VC4_SET_FIELD(vc4_encoder->clock_select,
-+ PV_CONTROL_CLK_SELECT) |
- PV_CONTROL_FIFO_CLR |
- PV_CONTROL_EN);
-
---- a/drivers/gpu/drm/vc4/vc4_regs.h
-+++ b/drivers/gpu/drm/vc4/vc4_regs.h
-@@ -184,6 +184,8 @@
-
- #define PV_V_CONTROL 0x04
- # define PV_VCONTROL_INTERLACE BIT(4)
-+# define PV_VCONTROL_DSI BIT(3)
-+# define PV_VCONTROL_COMMAND BIT(2)
- # define PV_VCONTROL_CONTINUOUS BIT(1)
- # define PV_VCONTROL_VIDEN BIT(0)
-
diff --git a/target/linux/brcm2708/patches-4.4/0441-drm-vc4-Start-switching-to-using-debugfs_reg32-helpe.patch b/target/linux/brcm2708/patches-4.4/0441-drm-vc4-Start-switching-to-using-debugfs_reg32-helpe.patch
deleted file mode 100644
index 853d95f..0000000
--- a/target/linux/brcm2708/patches-4.4/0441-drm-vc4-Start-switching-to-using-debugfs_reg32-helpe.patch
+++ /dev/null
@@ -1,156 +0,0 @@
-From 2c0dcd858253cb508f4c8ae571f4db6af2d44d93 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 20 May 2016 16:24:47 -0700
-Subject: [PATCH] drm/vc4: Start switching to using debugfs_reg32 helpers for
- debugfs.
-
-Every file was defining its own little struct and dumping for the
-regs, when there's a helper in debugfs for doing just this. However,
-instead of printing:
-
-PV_HORZA (0x000c): 0x00000000
-
-we now print:
-
-PV_HORZA = 0x00000000
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_crtc.c | 48 ++++++++++++++++--------------------------
- drivers/gpu/drm/vc4/vc4_drv.c | 13 ++++++++++++
- drivers/gpu/drm/vc4/vc4_drv.h | 6 ++++++
- 3 files changed, 37 insertions(+), 30 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_crtc.c
-+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
-@@ -35,6 +35,7 @@
- #include "drm_atomic_helper.h"
- #include "drm_crtc_helper.h"
- #include "linux/clk.h"
-+#include "linux/debugfs.h"
- #include "drm_fb_cma_helper.h"
- #include "linux/component.h"
- #include "linux/of_device.h"
-@@ -85,35 +86,25 @@ struct vc4_crtc_data {
- #define CRTC_WRITE(offset, val) writel(val, vc4_crtc->regs + (offset))
- #define CRTC_READ(offset) readl(vc4_crtc->regs + (offset))
-
--#define CRTC_REG(reg) { reg, #reg }
--static const struct {
-- u32 reg;
-- const char *name;
--} crtc_regs[] = {
-- CRTC_REG(PV_CONTROL),
-- CRTC_REG(PV_V_CONTROL),
-- CRTC_REG(PV_VSYNCD_EVEN),
-- CRTC_REG(PV_HORZA),
-- CRTC_REG(PV_HORZB),
-- CRTC_REG(PV_VERTA),
-- CRTC_REG(PV_VERTB),
-- CRTC_REG(PV_VERTA_EVEN),
-- CRTC_REG(PV_VERTB_EVEN),
-- CRTC_REG(PV_INTEN),
-- CRTC_REG(PV_INTSTAT),
-- CRTC_REG(PV_STAT),
-- CRTC_REG(PV_HACT_ACT),
-+static const struct debugfs_reg32 crtc_regs[] = {
-+ VC4_DEBUG_REG(PV_CONTROL),
-+ VC4_DEBUG_REG(PV_V_CONTROL),
-+ VC4_DEBUG_REG(PV_VSYNCD_EVEN),
-+ VC4_DEBUG_REG(PV_HORZA),
-+ VC4_DEBUG_REG(PV_HORZB),
-+ VC4_DEBUG_REG(PV_VERTA),
-+ VC4_DEBUG_REG(PV_VERTB),
-+ VC4_DEBUG_REG(PV_VERTA_EVEN),
-+ VC4_DEBUG_REG(PV_VERTB_EVEN),
-+ VC4_DEBUG_REG(PV_INTEN),
-+ VC4_DEBUG_REG(PV_INTSTAT),
-+ VC4_DEBUG_REG(PV_STAT),
-+ VC4_DEBUG_REG(PV_HACT_ACT),
- };
-
- static void vc4_crtc_dump_regs(struct vc4_crtc *vc4_crtc)
- {
-- int i;
--
-- for (i = 0; i < ARRAY_SIZE(crtc_regs); i++) {
-- DRM_INFO("0x%04x (%s): 0x%08x\n",
-- crtc_regs[i].reg, crtc_regs[i].name,
-- CRTC_READ(crtc_regs[i].reg));
-- }
-+ vc4_dump_regs32(crtc_regs, ARRAY_SIZE(crtc_regs), vc4_crtc->regs, "");
- }
-
- #ifdef CONFIG_DEBUG_FS
-@@ -136,11 +127,8 @@ int vc4_crtc_debugfs_regs(struct seq_fil
- return 0;
- vc4_crtc = to_vc4_crtc(crtc);
-
-- for (i = 0; i < ARRAY_SIZE(crtc_regs); i++) {
-- seq_printf(m, "%s (0x%04x): 0x%08x\n",
-- crtc_regs[i].name, crtc_regs[i].reg,
-- CRTC_READ(crtc_regs[i].reg));
-- }
-+ debugfs_print_regs32(m, crtc_regs, ARRAY_SIZE(crtc_regs),
-+ vc4_crtc->regs, "");
-
- return 0;
- }
---- a/drivers/gpu/drm/vc4/vc4_drv.c
-+++ b/drivers/gpu/drm/vc4/vc4_drv.c
-@@ -9,6 +9,7 @@
-
- #include <linux/clk.h>
- #include <linux/component.h>
-+#include <linux/debugfs.h>
- #include <linux/device.h>
- #include <linux/io.h>
- #include <linux/module.h>
-@@ -52,6 +53,18 @@ static void vc4_drm_preclose(struct drm_
- vc4_cancel_page_flip(crtc, file);
- }
-
-+void vc4_dump_regs32(const struct debugfs_reg32 *regs, unsigned int num_regs,
-+ void __iomem *base, const char *prefix)
-+{
-+ unsigned int i;
-+
-+ for (i = 0; i < num_regs; i++) {
-+ DRM_INFO("%s0x%04lx (%s): 0x%08x\n",
-+ prefix, regs[i].offset, regs[i].name,
-+ readl(base + regs[i].offset));
-+ }
-+}
-+
- static void vc4_lastclose(struct drm_device *dev)
- {
- struct vc4_dev *vc4 = to_vc4_dev(dev);
---- a/drivers/gpu/drm/vc4/vc4_drv.h
-+++ b/drivers/gpu/drm/vc4/vc4_drv.h
-@@ -9,6 +9,8 @@
- #include "drmP.h"
- #include "drm_gem_cma_helper.h"
-
-+struct debugfs_reg32;
-+
- struct vc4_dev {
- struct drm_device *dev;
-
-@@ -207,6 +209,8 @@ to_vc4_encoder(struct drm_encoder *encod
- #define HVS_READ(offset) readl(vc4->hvs->regs + offset)
- #define HVS_WRITE(offset, val) writel(val, vc4->hvs->regs + offset)
-
-+#define VC4_DEBUG_REG(reg) { .name = #reg, .offset = reg }
-+
- struct vc4_exec_info {
- /* Sequence number for this bin/render job. */
- uint64_t seqno;
-@@ -418,6 +422,8 @@ void vc4_debugfs_cleanup(struct drm_mino
-
- /* vc4_drv.c */
- void __iomem *vc4_ioremap_regs(struct platform_device *dev, int index);
-+void vc4_dump_regs32(const struct debugfs_reg32 *reg, unsigned int num_regs,
-+ void __iomem *base, const char *prefix);
-
- /* vc4_dpi.c */
- extern struct platform_driver vc4_dpi_driver;
diff --git a/target/linux/brcm2708/patches-4.4/0442-drm-vc4-Add-DSI1-driver.patch b/target/linux/brcm2708/patches-4.4/0442-drm-vc4-Add-DSI1-driver.patch
deleted file mode 100644
index a0003a5..0000000
--- a/target/linux/brcm2708/patches-4.4/0442-drm-vc4-Add-DSI1-driver.patch
+++ /dev/null
@@ -1,1914 +0,0 @@
-From fe5b388ac8cacd61ca01ff9a89f60af401fffee9 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Wed, 10 Feb 2016 11:42:32 -0800
-Subject: [PATCH] drm/vc4: Add DSI1 driver
-
-The DSI0 and DSI1 blocks on the 2835 are different but very similar
-hardware blocks. Some registers move around, and the featureset is
-slightly different, but they're clearly related. This doesn't enable
-DSI0, but some of the infrastructure is present.
-
-Also, this driver doesn't initialize the DSI successfully from
-poweron, so we currently require that the Raspberry Pi firmware enable
-it at boot time. From there, we just keep the same settings forever,
-and when poweroff is requested we just scan out black instead.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/Kconfig | 2 +
- drivers/gpu/drm/vc4/Makefile | 1 +
- drivers/gpu/drm/vc4/vc4_crtc.c | 41 +-
- drivers/gpu/drm/vc4/vc4_debugfs.c | 2 +
- drivers/gpu/drm/vc4/vc4_drv.c | 1 +
- drivers/gpu/drm/vc4/vc4_drv.h | 8 +
- drivers/gpu/drm/vc4/vc4_dsi.c | 1737 +++++++++++++++++++++++++++++++++++++
- 7 files changed, 1780 insertions(+), 12 deletions(-)
- create mode 100644 drivers/gpu/drm/vc4/vc4_dsi.c
-
---- a/drivers/gpu/drm/vc4/Kconfig
-+++ b/drivers/gpu/drm/vc4/Kconfig
-@@ -6,6 +6,8 @@ config DRM_VC4
- select DRM_KMS_CMA_HELPER
- select DRM_GEM_CMA_HELPER
- select DRM_PANEL
-+ select DRM_MIPI_DSI
-+ select CLKSRC_OF
- help
- Choose this option if you have a system that has a Broadcom
- VC4 GPU, such as the Raspberry Pi or other BCM2708/BCM2835.
---- a/drivers/gpu/drm/vc4/Makefile
-+++ b/drivers/gpu/drm/vc4/Makefile
-@@ -8,6 +8,7 @@ vc4-y := \
- vc4_crtc.o \
- vc4_drv.o \
- vc4_dpi.o \
-+ vc4_dsi.o \
- vc4_kms.o \
- vc4_gem.o \
- vc4_hdmi.o \
---- a/drivers/gpu/drm/vc4/vc4_crtc.c
-+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
-@@ -231,7 +231,7 @@ static void vc4_crtc_mode_set_nofb(struc
- bool is_dsi = (vc4_encoder->type == VC4_ENCODER_TYPE_DSI0 ||
- vc4_encoder->type == VC4_ENCODER_TYPE_DSI1);
- u32 format = is_dsi ? PV_CONTROL_FORMAT_DSIV_24 : PV_CONTROL_FORMAT_24;
-- bool debug_dump_regs = true;
-+ bool debug_dump_regs = false;
-
- if (debug_dump_regs) {
- DRM_INFO("CRTC %d regs before:\n", drm_crtc_index(crtc));
-@@ -327,6 +327,19 @@ static void vc4_crtc_disable(struct drm_
- int ret;
- require_hvs_enabled(dev);
-
-+ if (VC4_DSI_USE_FIRMWARE_SETUP &&
-+ (CRTC_READ(PV_V_CONTROL) & PV_VCONTROL_DSI)) {
-+ /* Skip disabling the PV/HVS for the channel if it was
-+ * connected to the DSI panel and we're using the
-+ * firmware setup. Instead, just set it to stuff
-+ * black in the composite output buffer.
-+ */
-+ HVS_WRITE(SCALER_DISPBKGNDX(vc4_crtc->channel),
-+ HVS_READ(SCALER_DISPBKGNDX(vc4_crtc->channel)) |
-+ SCALER_DISPBKGND_FILL);
-+ return;
-+ }
-+
- CRTC_WRITE(PV_V_CONTROL,
- CRTC_READ(PV_V_CONTROL) & ~PV_VCONTROL_VIDEN);
- ret = wait_for(!(CRTC_READ(PV_V_CONTROL) & PV_VCONTROL_VIDEN), 1);
-@@ -396,17 +409,19 @@ static int vc4_crtc_atomic_check(struct
- if (drm_atomic_connectors_for_crtc(state->state, crtc) > 1)
- return -EINVAL;
-
-- drm_atomic_crtc_state_for_each_plane(plane, state) {
-- struct drm_plane_state *plane_state =
-- state->state->plane_states[drm_plane_index(plane)];
--
-- /* plane might not have changed, in which case take
-- * current state:
-- */
-- if (!plane_state)
-- plane_state = plane->state;
-+ if (state->active) {
-+ drm_atomic_crtc_state_for_each_plane(plane, state) {
-+ struct drm_plane_state *plane_state =
-+ state->state->plane_states[drm_plane_index(plane)];
-+
-+ /* plane might not have changed, in which case take
-+ * current state:
-+ */
-+ if (!plane_state)
-+ plane_state = plane->state;
-
-- dlist_count += vc4_plane_dlist_size(plane_state);
-+ dlist_count += vc4_plane_dlist_size(plane_state);
-+ }
- }
-
- dlist_count++; /* Account for SCALER_CTL0_END. */
-@@ -439,8 +454,10 @@ static void vc4_crtc_atomic_flush(struct
- }
-
- /* Copy all the active planes' dlist contents to the hardware dlist. */
-- drm_atomic_crtc_for_each_plane(plane, crtc) {
-- dlist_next += vc4_plane_write_dlist(plane, dlist_next);
-+ if (crtc->state->active) {
-+ drm_atomic_crtc_for_each_plane(plane, crtc) {
-+ dlist_next += vc4_plane_write_dlist(plane, dlist_next);
-+ }
- }
-
- writel(SCALER_CTL0_END, dlist_next);
---- a/drivers/gpu/drm/vc4/vc4_debugfs.c
-+++ b/drivers/gpu/drm/vc4/vc4_debugfs.c
-@@ -19,6 +19,8 @@ static const struct drm_info_list vc4_de
- {"bo_stats", vc4_bo_stats_debugfs, 0},
- {"dpi_regs", vc4_dpi_debugfs_regs, 0},
- {"gem_exec", vc4_gem_exec_debugfs, 0},
-+ {"dsi0_regs", vc4_dsi_debugfs_regs, 0, (void *)(uintptr_t)0},
-+ {"dsi1_regs", vc4_dsi_debugfs_regs, 0, (void *)(uintptr_t)1},
- {"hdmi_regs", vc4_hdmi_debugfs_regs, 0},
- {"hvs_regs", vc4_hvs_debugfs_regs, 0},
- {"crtc0_regs", vc4_crtc_debugfs_regs, 0, (void *)(uintptr_t)0},
---- a/drivers/gpu/drm/vc4/vc4_drv.c
-+++ b/drivers/gpu/drm/vc4/vc4_drv.c
-@@ -294,6 +294,7 @@ static const struct component_master_ops
- static struct platform_driver *const component_drivers[] = {
- &vc4_hdmi_driver,
- &vc4_dpi_driver,
-+ &vc4_dsi_driver,
- &vc4_crtc_driver,
- &vc4_hvs_driver,
- &vc4_v3d_driver,
---- a/drivers/gpu/drm/vc4/vc4_drv.h
-+++ b/drivers/gpu/drm/vc4/vc4_drv.h
-@@ -19,6 +19,8 @@ struct vc4_dev {
- struct vc4_crtc *crtc[3];
- struct vc4_v3d *v3d;
- struct vc4_dpi *dpi;
-+ struct vc4_dsi *dsi0;
-+ struct vc4_dsi *dsi1;
-
- struct drm_fbdev_cma *fbdev;
- struct rpi_firmware *firmware;
-@@ -192,6 +194,8 @@ enum vc4_encoder_type {
- VC4_ENCODER_TYPE_DPI,
- };
-
-+#define VC4_DSI_USE_FIRMWARE_SETUP true
-+
- struct vc4_encoder {
- struct drm_encoder base;
- enum vc4_encoder_type type;
-@@ -429,6 +433,10 @@ void vc4_dump_regs32(const struct debugf
- extern struct platform_driver vc4_dpi_driver;
- int vc4_dpi_debugfs_regs(struct seq_file *m, void *unused);
-
-+/* vc4_dsi.c */
-+extern struct platform_driver vc4_dsi_driver;
-+int vc4_dsi_debugfs_regs(struct seq_file *m, void *unused);
-+
- /* vc4_gem.c */
- void vc4_gem_init(struct drm_device *dev);
- void vc4_gem_destroy(struct drm_device *dev);
---- /dev/null
-+++ b/drivers/gpu/drm/vc4/vc4_dsi.c
-@@ -0,0 +1,1737 @@
-+ /*
-+ * Copyright (C) 2016 Broadcom Limited
-+ *
-+ * This program is free software; you can redistribute it and/or modify it
-+ * under the terms of the GNU General Public License version 2 as published by
-+ * the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful, but WITHOUT
-+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
-+ * more details.
-+ *
-+ * You should have received a copy of the GNU General Public License along with
-+ * this program. If not, see <http://www.gnu.org/licenses/>.
-+ */
-+
-+/**
-+ * DOC: VC4 DSI0 module
-+ */
-+
-+#include "drm_atomic_helper.h"
-+#include "drm_crtc_helper.h"
-+#include "drm_edid.h"
-+#include "drm_mipi_dsi.h"
-+#include "drm_panel.h"
-+#include "linux/clk.h"
-+#include "linux/clk-provider.h"
-+#include "linux/completion.h"
-+#include "linux/component.h"
-+#include "linux/debugfs.h"
-+#include "linux/dmaengine.h"
-+#include "linux/i2c.h"
-+#include "linux/of_address.h"
-+#include "linux/of_gpio.h"
-+#include "linux/of_platform.h"
-+#include "vc4_drv.h"
-+#include "vc4_regs.h"
-+
-+#define DSI_CMD_FIFO_DEPTH 16
-+#define DSI_PIX_FIFO_DEPTH 256
-+#define DSI_PIX_FIFO_WIDTH 4
-+
-+#define DSI0_CTRL 0x00
-+
-+/* Command packet control. */
-+#define DSI0_TXPKT1C 0x04 /* AKA PKTC */
-+#define DSI1_TXPKT1C 0x04
-+# define DSI_TXPKT1C_TRIG_CMD_MASK VC4_MASK(31, 24)
-+# define DSI_TXPKT1C_TRIG_CMD_SHIFT 24
-+# define DSI_TXPKT1C_CMD_REPEAT_MASK VC4_MASK(23, 10)
-+# define DSI_TXPKT1C_CMD_REPEAT_SHIFT 10
-+
-+# define DSI_TXPKT1C_DISPLAY_NO_MASK VC4_MASK(9, 8)
-+# define DSI_TXPKT1C_DISPLAY_NO_SHIFT 8
-+/* Short, trigger, BTA, or a long packet that fits all in CMDFIFO. */
-+# define DSI_TXPKT1C_DISPLAY_NO_SHORT 0
-+/* Primary display where cmdfifo provides part of the payload and
-+ * pixelvalve the rest.
-+ */
-+# define DSI_TXPKT1C_DISPLAY_NO_PRIMARY 1
-+/* Secondary display where cmdfifo provides part of the payload and
-+ * pixfifo the rest.
-+ */
-+# define DSI_TXPKT1C_DISPLAY_NO_SECONDARY 2
-+
-+# define DSI_TXPKT1C_CMD_TX_TIME_MASK VC4_MASK(7, 6)
-+# define DSI_TXPKT1C_CMD_TX_TIME_SHIFT 6
-+# define DSI_TXPKT1C_CMD_CTRL_MASK VC4_MASK(5, 4)
-+# define DSI_TXPKT1C_CMD_CTRL_SHIFT 4
-+/* Command only. Uses TXPKT1H and DISPLAY_NO */
-+# define DSI_TXPKT1C_CMD_CTRL_TX 0
-+/* Command with BTA for either ack or read data. */
-+# define DSI_TXPKT1C_CMD_CTRL_RX 1
-+/* Trigger according to TRIG_CMD */
-+# define DSI_TXPKT1C_CMD_CTRL_TRIG 2
-+/* BTA alone for getting error status after a command, or a TE trigger
-+ * without a previous command.
-+ */
-+# define DSI_TXPKT1C_CMD_CTRL_BTA 3
-+
-+# define DSI_TXPKT1C_CMD_MODE_LP BIT(3)
-+# define DSI_TXPKT1C_CMD_TYPE_LONG BIT(2)
-+# define DSI_TXPKT1C_CMD_TE_EN BIT(1)
-+# define DSI_TXPKT1C_CMD_EN BIT(0)
-+
-+/* Command packet header. */
-+#define DSI0_TXPKT1H 0x08 /* AKA PKTH */
-+#define DSI1_TXPKT1H 0x08
-+# define DSI_TXPKT1H_BC_CMDFIFO_MASK VC4_MASK(31, 24)
-+# define DSI_TXPKT1H_BC_CMDFIFO_SHIFT 24
-+# define DSI_TXPKT1H_BC_PARAM_MASK VC4_MASK(23, 8)
-+# define DSI_TXPKT1H_BC_PARAM_SHIFT 8
-+# define DSI_TXPKT1H_BC_DT_MASK VC4_MASK(7, 0)
-+# define DSI_TXPKT1H_BC_DT_SHIFT 0
-+
-+#define DSI0_RXPKT1H 0x0c /* AKA RX1_PKTH */
-+#define DSI1_RXPKT1H 0x14
-+# define DSI_RXPKT1H_CRC_ERR BIT(31)
-+# define DSI_RXPKT1H_DET_ERR BIT(30)
-+# define DSI_RXPKT1H_ECC_ERR BIT(29)
-+# define DSI_RXPKT1H_COR_ERR BIT(28)
-+# define DSI_RXPKT1H_INCOMP_PKT BIT(25)
-+# define DSI_RXPKT1H_PKT_TYPE_LONG BIT(24)
-+/* Byte count if DSI_RXPKT1H_PKT_TYPE_LONG */
-+# define DSI_RXPKT1H_BC_PARAM_MASK VC4_MASK(23, 8)
-+# define DSI_RXPKT1H_BC_PARAM_SHIFT 8
-+/* Short return bytes if !DSI_RXPKT1H_PKT_TYPE_LONG */
-+# define DSI_RXPKT1H_SHORT_1_MASK VC4_MASK(23, 16)
-+# define DSI_RXPKT1H_SHORT_1_SHIFT 16
-+# define DSI_RXPKT1H_SHORT_0_MASK VC4_MASK(15, 8)
-+# define DSI_RXPKT1H_SHORT_0_SHIFT 8
-+# define DSI_RXPKT1H_DT_LP_CMD_MASK VC4_MASK(7, 0)
-+# define DSI_RXPKT1H_DT_LP_CMD_SHIFT 0
-+
-+#define DSI0_RXPKT2H 0x10 /* AKA RX2_PKTH */
-+#define DSI1_RXPKT2H 0x18
-+# define DSI_RXPKT1H_DET_ERR BIT(30)
-+# define DSI_RXPKT1H_ECC_ERR BIT(29)
-+# define DSI_RXPKT1H_COR_ERR BIT(28)
-+# define DSI_RXPKT1H_INCOMP_PKT BIT(25)
-+# define DSI_RXPKT1H_BC_PARAM_MASK VC4_MASK(23, 8)
-+# define DSI_RXPKT1H_BC_PARAM_SHIFT 8
-+# define DSI_RXPKT1H_DT_MASK VC4_MASK(7, 0)
-+# define DSI_RXPKT1H_DT_SHIFT 0
-+
-+#define DSI0_TXPKT_CMD_FIFO 0x14 /* AKA CMD_DATAF */
-+#define DSI1_TXPKT_CMD_FIFO 0x1c
-+
-+#define DSI0_DISP0_CTRL 0x18
-+# define DSI_DISP0_PIX_CLK_DIV_MASK VC4_MASK(21, 13)
-+# define DSI_DISP0_PIX_CLK_DIV_SHIFT 13
-+# define DSI_DISP0_LP_STOP_CTRL_MASK VC4_MASK(12, 11)
-+# define DSI_DISP0_LP_STOP_CTRL_SHIFT 11
-+# define DSI_DISP0_LP_STOP_DISABLE 0
-+# define DSI_DISP0_LP_STOP_PERLINE 1
-+# define DSI_DISP0_LP_STOP_PERFRAME 2
-+
-+/* Transmit RGB pixels and null packets only during HACTIVE, instead
-+ * of going to LP-STOP.
-+ */
-+# define DSI_DISP_HACTIVE_NULL BIT(10)
-+/* Transmit blanking packet only during vblank, instead of allowing LP-STOP. */
-+# define DSI_DISP_VBLP_CTRL BIT(9)
-+/* Transmit blanking packet only during HFP, instead of allowing LP-STOP. */
-+# define DSI_DISP_HFP_CTRL BIT(8)
-+/* Transmit blanking packet only during HBP, instead of allowing LP-STOP. */
-+# define DSI_DISP_HBP_CTRL BIT(7)
-+# define DSI_DISP0_CHANNEL_MASK VC4_MASK(6, 5)
-+# define DSI_DISP0_CHANNEL_SHIFT 5
-+/* Enables and end events for HSYNC/VSYNC, not just start events. */
-+# define DSI_DISP0_ST_END BIT(4)
-+# define DSI_DISP0_PFORMAT_MASK VC4_MASK(3, 2)
-+# define DSI_DISP0_PFORMAT_SHIFT 2
-+# define DSI_PFORMAT_RGB565 0
-+# define DSI_PFORMAT_RGB666_PACKED 1
-+# define DSI_PFORMAT_RGB666 2
-+# define DSI_PFORMAT_RGB888 3
-+/* Default is VIDEO mode. */
-+# define DSI_DISP0_COMMAND_MODE BIT(1)
-+# define DSI_DISP0_ENABLE BIT(0)
-+
-+#define DSI0_DISP1_CTRL 0x1c
-+#define DSI1_DISP1_CTRL 0x2c
-+/* Format of the data written to TXPKT_PIX_FIFO. */
-+# define DSI_DISP1_PFORMAT_MASK VC4_MASK(2, 1)
-+# define DSI_DISP1_PFORMAT_SHIFT 1
-+# define DSI_DISP1_PFORMAT_16BIT 0
-+# define DSI_DISP1_PFORMAT_24BIT 1
-+# define DSI_DISP1_PFORMAT_32BIT_LE 2
-+# define DSI_DISP1_PFORMAT_32BIT_BE 3
-+
-+/* DISP1 is always command mode. */
-+# define DSI_DISP1_ENABLE BIT(0)
-+
-+#define DSI0_TXPKT_PIX_FIFO 0x20 /* AKA PIX_FIFO */
-+
-+#define DSI0_INT_STAT 0x24
-+#define DSI0_INT_EN 0x28
-+# define DSI1_INT_PHY_D3_ULPS BIT(30)
-+# define DSI1_INT_PHY_D3_STOP BIT(29)
-+# define DSI1_INT_PHY_D2_ULPS BIT(28)
-+# define DSI1_INT_PHY_D2_STOP BIT(27)
-+# define DSI1_INT_PHY_D1_ULPS BIT(26)
-+# define DSI1_INT_PHY_D1_STOP BIT(25)
-+# define DSI1_INT_PHY_D0_ULPS BIT(24)
-+# define DSI1_INT_PHY_D0_STOP BIT(23)
-+# define DSI1_INT_FIFO_ERR BIT(22)
-+# define DSI1_INT_PHY_DIR_RTF BIT(21)
-+# define DSI1_INT_PHY_RXLPDT BIT(20)
-+# define DSI1_INT_PHY_RXTRIG BIT(19)
-+# define DSI1_INT_PHY_D0_LPDT BIT(18)
-+# define DSI1_INT_PHY_DIR_FTR BIT(17)
-+
-+/* Signaled when the clock lane enters the given state. */
-+# define DSI1_INT_PHY_CLOCK_ULPS BIT(16)
-+# define DSI1_INT_PHY_CLOCK_HS BIT(15)
-+# define DSI1_INT_PHY_CLOCK_STOP BIT(14)
-+
-+/* Signaled on timeouts */
-+# define DSI1_INT_PR_TO BIT(13)
-+# define DSI1_INT_TA_TO BIT(12)
-+# define DSI1_INT_LPRX_TO BIT(11)
-+# define DSI1_INT_HSTX_TO BIT(10)
-+
-+/* Contention on a line when trying to drive the line low */
-+# define DSI1_INT_ERR_CONT_LP1 BIT(9)
-+# define DSI1_INT_ERR_CONT_LP0 BIT(8)
-+
-+/* Control error: incorrect line state sequence on data lane 0. */
-+# define DSI1_INT_ERR_CONTROL BIT(7)
-+/* LPDT synchronization error (bits received not a multiple of 8. */
-+
-+# define DSI1_INT_ERR_SYNC_ESC BIT(6)
-+/* Signaled after receiving an error packet from the display in
-+ * response to a read.
-+ */
-+# define DSI1_INT_RXPKT2 BIT(5)
-+/* Signaled after receiving a packet. The header and optional short
-+ * response will be in RXPKT1H, and a long response will be in the
-+ * RXPKT_FIFO.
-+ */
-+# define DSI1_INT_RXPKT1 BIT(4)
-+# define DSI1_INT_TXPKT2_DONE BIT(3)
-+# define DSI1_INT_TXPKT2_END BIT(2)
-+/* Signaled after all repeats of TXPKT1 are transferred. */
-+# define DSI1_INT_TXPKT1_DONE BIT(1)
-+/* Signaled after each TXPKT1 repeat is scheduled. */
-+# define DSI1_INT_TXPKT1_END BIT(0)
-+
-+#define DSI1_INTERRUPTS_ALWAYS_ENABLED (DSI1_INT_ERR_SYNC_ESC | \
-+ DSI1_INT_ERR_CONTROL | \
-+ DSI1_INT_ERR_CONT_LP0 | \
-+ DSI1_INT_ERR_CONT_LP1 | \
-+ DSI1_INT_HSTX_TO | \
-+ DSI1_INT_LPRX_TO | \
-+ DSI1_INT_TA_TO | \
-+ DSI1_INT_PR_TO)
-+
-+#define DSI0_STAT 0x2c
-+#define DSI0_HSTX_TO_CNT 0x30
-+#define DSI0_LPRX_TO_CNT 0x34
-+#define DSI0_TA_TO_CNT 0x38
-+#define DSI0_PR_TO_CNT 0x3c
-+#define DSI0_PHYC 0x40
-+# define DSI1_PHYC_ESC_CLK_LPDT_MASK VC4_MASK(25, 20)
-+# define DSI1_PHYC_ESC_CLK_LPDT_SHIFT 20
-+# define DSI1_PHYC_HS_CLK_CONTINUOUS BIT(18)
-+# define DSI1_PHYC_CLANE_ULPS BIT(17)
-+# define DSI0_PHYC_ESC_CLK_LPDT_MASK VC4_MASK(17, 12)
-+# define DSI0_PHYC_ESC_CLK_LPDT_SHIFT 12
-+# define DSI1_PHYC_CLANE_ENABLE BIT(16)
-+# define DSI_PHYC_DLANE3_ULPS BIT(13)
-+# define DSI_PHYC_DLANE3_ENABLE BIT(12)
-+# define DSI0_PHYC_HS_CLK_CONTINUOUS BIT(10)
-+# define DSI0_PHYC_CLANE_ULPS BIT(9)
-+# define DSI_PHYC_DLANE2_ULPS BIT(9)
-+# define DSI0_PHYC_CLANE_ENABLE BIT(8)
-+# define DSI_PHYC_DLANE2_ENABLE BIT(8)
-+# define DSI_PHYC_DLANE1_ULPS BIT(5)
-+# define DSI_PHYC_DLANE1_ENABLE BIT(4)
-+# define DSI_PHYC_DLANE0_FORCE_STOP BIT(2)
-+# define DSI_PHYC_DLANE0_ULPS BIT(1)
-+# define DSI_PHYC_DLANE0_ENABLE BIT(0)
-+
-+#define DSI0_HS_CLT0 0x44
-+#define DSI0_HS_CLT1 0x48
-+#define DSI0_HS_CLT2 0x4c
-+#define DSI0_HS_DLT3 0x50
-+#define DSI0_HS_DLT4 0x54
-+#define DSI0_HS_DLT5 0x58
-+#define DSI0_HS_DLT6 0x5c
-+#define DSI0_HS_DLT7 0x60
-+
-+#define DSI0_PHY_AFEC0 0x64
-+# define DSI0_PHY_AFEC0_DDR2CLK_EN BIT(26)
-+# define DSI0_PHY_AFEC0_DDRCLK_EN BIT(25)
-+# define DSI0_PHY_AFEC0_LATCH_ULPS BIT(24)
-+# define DSI1_PHY_AFEC0_IDR_DLANE3_MASK VC4_MASK(31, 29)
-+# define DSI1_PHY_AFEC0_IDR_DLANE3_SHIFT 29
-+# define DSI1_PHY_AFEC0_IDR_DLANE2_MASK VC4_MASK(28, 26)
-+# define DSI1_PHY_AFEC0_IDR_DLANE2_SHIFT 26
-+# define DSI1_PHY_AFEC0_IDR_DLANE1_MASK VC4_MASK(27, 23)
-+# define DSI1_PHY_AFEC0_IDR_DLANE1_SHIFT 23
-+# define DSI1_PHY_AFEC0_IDR_DLANE0_MASK VC4_MASK(22, 20)
-+# define DSI1_PHY_AFEC0_IDR_DLANE0_SHIFT 20
-+# define DSI1_PHY_AFEC0_IDR_CLANE_MASK VC4_MASK(19, 17)
-+# define DSI1_PHY_AFEC0_IDR_CLANE_SHIFT 17
-+# define DSI0_PHY_AFEC0_ACTRL_DLANE1_MASK VC4_MASK(23, 20)
-+# define DSI0_PHY_AFEC0_ACTRL_DLANE1_SHIFT 20
-+# define DSI0_PHY_AFEC0_ACTRL_DLANE0_MASK VC4_MASK(19, 16)
-+# define DSI0_PHY_AFEC0_ACTRL_DLANE0_SHIFT 16
-+# define DSI0_PHY_AFEC0_ACTRL_CLANE_MASK VC4_MASK(15, 12)
-+# define DSI0_PHY_AFEC0_ACTRL_CLANE_SHIFT 12
-+# define DSI1_PHY_AFEC0_DDR2CLK_EN BIT(16)
-+# define DSI1_PHY_AFEC0_DDRCLK_EN BIT(15)
-+# define DSI1_PHY_AFEC0_LATCH_ULPS BIT(14)
-+# define DSI1_PHY_AFEC0_RESET BIT(13)
-+# define DSI1_PHY_AFEC0_PD BIT(12)
-+# define DSI0_PHY_AFEC0_RESET BIT(11)
-+# define DSI1_PHY_AFEC0_PD_BG BIT(11)
-+# define DSI0_PHY_AFEC0_PD BIT(10)
-+# define DSI1_PHY_AFEC0_PD_DLANE3 BIT(10)
-+# define DSI0_PHY_AFEC0_PD_BG BIT(9)
-+# define DSI1_PHY_AFEC0_PD_DLANE2 BIT(9)
-+# define DSI0_PHY_AFEC0_PD_DLANE1 BIT(8)
-+# define DSI1_PHY_AFEC0_PD_DLANE1 BIT(8)
-+# define DSI_PHY_AFEC0_PTATADJ_MASK VC4_MASK(7, 4)
-+# define DSI_PHY_AFEC0_PTATADJ_SHIFT 4
-+# define DSI_PHY_AFEC0_CTATADJ_MASK VC4_MASK(3, 0)
-+# define DSI_PHY_AFEC0_CTATADJ_SHIFT 0
-+
-+#define DSI0_PHY_AFEC1 0x68
-+# define DSI0_PHY_AFEC1_IDR_DLANE1_MASK VC4_MASK(10, 8)
-+# define DSI0_PHY_AFEC1_IDR_DLANE1_SHIFT 8
-+# define DSI0_PHY_AFEC1_IDR_DLANE0_MASK VC4_MASK(6, 4)
-+# define DSI0_PHY_AFEC1_IDR_DLANE0_SHIFT 4
-+# define DSI0_PHY_AFEC1_IDR_CLANE_MASK VC4_MASK(2, 0)
-+# define DSI0_PHY_AFEC1_IDR_CLANE_SHIFT 0
-+
-+#define DSI0_TST_SEL 0x6c
-+#define DSI0_TST_MON 0x70
-+#define DSI0_ID 0x74
-+# define DSI_ID_VALUE 0x00647369
-+
-+
-+#define DSI1_CTRL 0x00
-+# define DSI_CTRL_HS_CLKC_MASK VC4_MASK(15, 14)
-+# define DSI_CTRL_HS_CLKC_SHIFT 14
-+# define DSI_CTRL_HS_CLKC_BYTE 0
-+# define DSI_CTRL_HS_CLKC_DDR2 1
-+# define DSI_CTRL_HS_CLKC_DDR 2
-+
-+# define DSI_CTRL_RX_LPDT_EOT_DISABLE BIT(13)
-+# define DSI_CTRL_LPDT_EOT_DISABLE BIT(12)
-+# define DSI_CTRL_HSDT_EOT_DISABLE BIT(11)
-+# define DSI_CTRL_SOFT_RESET_CFG BIT(10)
-+# define DSI_CTRL_CAL_BYTE BIT(9)
-+# define DSI_CTRL_INV_BYTE BIT(8)
-+# define DSI_CTRL_CLR_LDF BIT(7)
-+# define DSI0_CTRL_CLR_PBCF BIT(6)
-+# define DSI1_CTRL_CLR_RXF BIT(6)
-+# define DSI0_CTRL_CLR_CPBCF BIT(5)
-+# define DSI1_CTRL_CLR_PDF BIT(5)
-+# define DSI0_CTRL_CLR_PDF BIT(4)
-+# define DSI1_CTRL_CLR_CDF BIT(4)
-+# define DSI0_CTRL_CLR_CDF BIT(3)
-+# define DSI0_CTRL_CTRL2 BIT(2)
-+# define DSI1_CTRL_DISABLE_DISP_CRCC BIT(2)
-+# define DSI0_CTRL_CTRL1 BIT(1)
-+# define DSI1_CTRL_DISABLE_DISP_ECCC BIT(1)
-+# define DSI0_CTRL_CTRL0 BIT(0)
-+# define DSI1_CTRL_EN BIT(0)
-+# define DSI0_CTRL_RESET_FIFOS (DSI_CTRL_CLR_LDF | \
-+ DSI0_CTRL_CLR_PBCF | \
-+ DSI0_CTRL_CLR_CPBCF | \
-+ DSI0_CTRL_CLR_PDF | \
-+ DSI0_CTRL_CLR_CDF)
-+# define DSI1_CTRL_RESET_FIFOS (DSI_CTRL_CLR_LDF | \
-+ DSI1_CTRL_CLR_RXF | \
-+ DSI1_CTRL_CLR_PDF | \
-+ DSI1_CTRL_CLR_CDF)
-+
-+#define DSI1_TXPKT2C 0x0c
-+#define DSI1_TXPKT2H 0x10
-+#define DSI1_TXPKT_PIX_FIFO 0x20
-+#define DSI1_RXPKT_FIFO 0x24
-+#define DSI1_DISP0_CTRL 0x28
-+#define DSI1_INT_STAT 0x30
-+#define DSI1_INT_EN 0x34
-+
-+/* State reporting bits. These mostly behave like INT_STAT, where
-+ * writing a 1 clears the bit.
-+ */
-+#define DSI1_STAT 0x38
-+# define DSI1_STAT_PHY_D3_ULPS BIT(31)
-+# define DSI1_STAT_PHY_D3_STOP BIT(30)
-+# define DSI1_STAT_PHY_D2_ULPS BIT(29)
-+# define DSI1_STAT_PHY_D2_STOP BIT(28)
-+# define DSI1_STAT_PHY_D1_ULPS BIT(27)
-+# define DSI1_STAT_PHY_D1_STOP BIT(26)
-+# define DSI1_STAT_PHY_D0_ULPS BIT(25)
-+# define DSI1_STAT_PHY_D0_STOP BIT(24)
-+# define DSI1_STAT_FIFO_ERR BIT(23)
-+# define DSI1_STAT_PHY_RXLPDT BIT(22)
-+# define DSI1_STAT_PHY_RXTRIG BIT(21)
-+# define DSI1_STAT_PHY_D0_LPDT BIT(20)
-+/* Set when in forward direction */
-+# define DSI1_STAT_PHY_DIR BIT(19)
-+# define DSI1_STAT_PHY_CLOCK_ULPS BIT(18)
-+# define DSI1_STAT_PHY_CLOCK_HS BIT(17)
-+# define DSI1_STAT_PHY_CLOCK_STOP BIT(16)
-+# define DSI1_STAT_PR_TO BIT(15)
-+# define DSI1_STAT_TA_TO BIT(14)
-+# define DSI1_STAT_LPRX_TO BIT(13)
-+# define DSI1_STAT_HSTX_TO BIT(12)
-+# define DSI1_STAT_ERR_CONT_LP1 BIT(11)
-+# define DSI1_STAT_ERR_CONT_LP0 BIT(10)
-+# define DSI1_STAT_ERR_CONTROL BIT(9)
-+# define DSI1_STAT_ERR_SYNC_ESC BIT(8)
-+# define DSI1_STAT_RXPKT2 BIT(7)
-+# define DSI1_STAT_RXPKT1 BIT(6)
-+# define DSI1_STAT_TXPKT2_BUSY BIT(5)
-+# define DSI1_STAT_TXPKT2_DONE BIT(4)
-+# define DSI1_STAT_TXPKT2_END BIT(3)
-+# define DSI1_STAT_TXPKT1_BUSY BIT(2)
-+# define DSI1_STAT_TXPKT1_DONE BIT(1)
-+# define DSI1_STAT_TXPKT1_END BIT(0)
-+
-+#define DSI1_HSTX_TO_CNT 0x3c
-+#define DSI1_LPRX_TO_CNT 0x40
-+#define DSI1_TA_TO_CNT 0x44
-+#define DSI1_PR_TO_CNT 0x48
-+#define DSI1_PHYC 0x4c
-+
-+#define DSI1_HS_CLT0 0x50
-+# define DSI_HS_CLT0_CZERO_MASK VC4_MASK(26, 18)
-+# define DSI_HS_CLT0_CZERO_SHIFT 18
-+# define DSI_HS_CLT0_CPRE_MASK VC4_MASK(17, 9)
-+# define DSI_HS_CLT0_CPRE_SHIFT 9
-+# define DSI_HS_CLT0_CPREP_MASK VC4_MASK(8, 0)
-+# define DSI_HS_CLT0_CPREP_SHIFT 0
-+
-+#define DSI1_HS_CLT1 0x54
-+# define DSI_HS_CLT1_CTRAIL_MASK VC4_MASK(17, 9)
-+# define DSI_HS_CLT1_CTRAIL_SHIFT 9
-+# define DSI_HS_CLT1_CPOST_MASK VC4_MASK(8, 0)
-+# define DSI_HS_CLT1_CPOST_SHIFT 0
-+
-+#define DSI1_HS_CLT2 0x58
-+# define DSI_HS_CLT2_WUP_MASK VC4_MASK(23, 0)
-+# define DSI_HS_CLT2_WUP_SHIFT 0
-+
-+#define DSI1_HS_DLT3 0x5c
-+# define DSI_HS_DLT3_EXIT_MASK VC4_MASK(26, 18)
-+# define DSI_HS_DLT3_EXIT_SHIFT 18
-+# define DSI_HS_DLT3_ZERO_MASK VC4_MASK(17, 9)
-+# define DSI_HS_DLT3_ZERO_SHIFT 9
-+# define DSI_HS_DLT3_PRE_MASK VC4_MASK(8, 0)
-+# define DSI_HS_DLT3_PRE_SHIFT 0
-+
-+#define DSI1_HS_DLT4 0x60
-+# define DSI_HS_DLT4_ANLAT_MASK VC4_MASK(22, 18)
-+# define DSI_HS_DLT4_ANLAT_SHIFT 18
-+# define DSI_HS_DLT4_TRAIL_MASK VC4_MASK(17, 9)
-+# define DSI_HS_DLT4_TRAIL_SHIFT 9
-+# define DSI_HS_DLT4_LPX_MASK VC4_MASK(8, 0)
-+# define DSI_HS_DLT4_LPX_SHIFT 0
-+
-+#define DSI1_HS_DLT5 0x64
-+# define DSI_HS_DLT5_INIT_MASK VC4_MASK(23, 0)
-+# define DSI_HS_DLT5_INIT_SHIFT 0
-+
-+#define DSI1_HS_DLT6 0x68
-+# define DSI_HS_DLT6_TA_GET_MASK VC4_MASK(31, 24)
-+# define DSI_HS_DLT6_TA_GET_SHIFT 24
-+# define DSI_HS_DLT6_TA_SURE_MASK VC4_MASK(23, 16)
-+# define DSI_HS_DLT6_TA_SURE_SHIFT 16
-+# define DSI_HS_DLT6_TA_GO_MASK VC4_MASK(15, 8)
-+# define DSI_HS_DLT6_TA_GO_SHIFT 8
-+# define DSI_HS_DLT6_LP_LPX_MASK VC4_MASK(7, 0)
-+# define DSI_HS_DLT6_LP_LPX_SHIFT 0
-+
-+#define DSI1_HS_DLT7 0x6c
-+# define DSI_HS_DLT7_LP_WUP_MASK VC4_MASK(23, 0)
-+# define DSI_HS_DLT7_LP_WUP_SHIFT 0
-+
-+#define DSI1_PHY_AFEC0 0x70
-+
-+#define DSI1_PHY_AFEC1 0x74
-+# define DSI1_PHY_AFEC1_ACTRL_DLANE3_MASK VC4_MASK(19, 16)
-+# define DSI1_PHY_AFEC1_ACTRL_DLANE3_SHIFT 16
-+# define DSI1_PHY_AFEC1_ACTRL_DLANE2_MASK VC4_MASK(15, 12)
-+# define DSI1_PHY_AFEC1_ACTRL_DLANE2_SHIFT 12
-+# define DSI1_PHY_AFEC1_ACTRL_DLANE1_MASK VC4_MASK(11, 8)
-+# define DSI1_PHY_AFEC1_ACTRL_DLANE1_SHIFT 8
-+# define DSI1_PHY_AFEC1_ACTRL_DLANE0_MASK VC4_MASK(7, 4)
-+# define DSI1_PHY_AFEC1_ACTRL_DLANE0_SHIFT 4
-+# define DSI1_PHY_AFEC1_ACTRL_CLANE_MASK VC4_MASK(3, 0)
-+# define DSI1_PHY_AFEC1_ACTRL_CLANE_SHIFT 0
-+
-+#define DSI1_TST_SEL 0x78
-+#define DSI1_TST_MON 0x7c
-+#define DSI1_PHY_TST1 0x80
-+#define DSI1_PHY_TST2 0x84
-+#define DSI1_PHY_FIFO_STAT 0x88
-+/* Actually, all registers in the range that aren't otherwise claimed
-+ * will return the ID.
-+ */
-+#define DSI1_ID 0x8c
-+
-+/* General DSI hardware state. */
-+struct vc4_dsi {
-+ struct platform_device *pdev;
-+
-+ struct mipi_dsi_host dsi_host;
-+ struct drm_encoder *encoder;
-+ struct drm_connector *connector;
-+ struct drm_panel *panel;
-+
-+ void __iomem *regs;
-+
-+ struct dma_chan *reg_dma_chan;
-+ dma_addr_t reg_dma_paddr;
-+ u32 *reg_dma_mem;
-+ dma_addr_t reg_paddr;
-+
-+ /* Whether we're on bcm2835's DSI0 or DSI1. */
-+ int port;
-+
-+ /* DSI channel for the panel we're connected to. */
-+ u32 channel;
-+ u32 lanes;
-+ enum mipi_dsi_pixel_format format;
-+ u32 mode_flags;
-+
-+ /* Input clock to the PHY, for the DSI escape clock. */
-+ struct clk *escape_clock;
-+
-+ /* Input clock to the PHY, used to generate the DSI bit
-+ * clock.
-+ */
-+ struct clk *pll_phy_clock;
-+
-+ /* Byte clock generated within the DSI PHY. */
-+ struct clk_hw phy_byte_clock;
-+
-+ struct clk_onecell_data clk_onecell;
-+
-+ /* Pixel clock output to the pixelvalve, generated from the
-+ * byte clock.
-+ */
-+ struct clk *pixel_clock;
-+
-+ struct completion xfer_completion;
-+ int xfer_result;
-+
-+ bool use_firmware_setup;
-+};
-+
-+static inline void
-+dsi_write(struct vc4_dsi *dsi, u32 offset, u32 val)
-+{
-+ struct dma_chan *chan = dsi->reg_dma_chan;
-+ struct dma_async_tx_descriptor *tx;
-+ dma_cookie_t cookie;
-+ int ret;
-+
-+#if 0 /* XXX */
-+ dev_info(&dsi->pdev->dev, "WRITE 0x%04x -> 0x%08x\n", offset, val);
-+#endif
-+
-+ if (!chan) {
-+ writel(val, dsi->regs + offset);
-+ return;
-+ }
-+
-+ *dsi->reg_dma_mem = val;
-+
-+ tx = chan->device->device_prep_dma_memcpy(chan,
-+ dsi->reg_paddr + offset,
-+ dsi->reg_dma_paddr,
-+ 4, 0);
-+ if (!tx) {
-+ DRM_ERROR("Failed to set up DMA register write\n");
-+ return;
-+ }
-+
-+ cookie = tx->tx_submit(tx);
-+ ret = dma_submit_error(cookie);
-+ if (ret) {
-+ DRM_ERROR("Failed to submit DMA: %d\n", ret);
-+ return;
-+ }
-+ ret = dma_sync_wait(chan, cookie);
-+ if (ret)
-+ DRM_ERROR("Failed to wait for DMA: %d\n", ret);
-+
-+#if 0 /* XXX */
-+ if (offset != DSI1_TXPKT_CMD_FIFO &&
-+ offset != DSI1_TXPKT_PIX_FIFO) {
-+ dev_info(&dsi->pdev->dev,
-+ " -> 0x%08x\n",
-+ readl(dsi->regs + (offset)));
-+ }
-+#endif
-+}
-+
-+#define DSI_READ(offset) readl(dsi->regs + (offset))
-+#define DSI_WRITE(offset, val) dsi_write(dsi, offset, val)
-+#define DSI_PORT_READ(offset) \
-+ DSI_READ(dsi->port ? DSI1_##offset : DSI0_##offset)
-+#define DSI_PORT_WRITE(offset, val) \
-+ DSI_WRITE(dsi->port ? DSI1_##offset : DSI0_##offset, val)
-+#define DSI_PORT_BIT(bit) (dsi->port ? DSI1_##bit : DSI0_##bit)
-+
-+/* VC4 DSI encoder KMS struct */
-+struct vc4_dsi_encoder {
-+ struct vc4_encoder base;
-+ struct vc4_dsi *dsi;
-+};
-+
-+static inline struct vc4_dsi_encoder *
-+to_vc4_dsi_encoder(struct drm_encoder *encoder)
-+{
-+ return container_of(encoder, struct vc4_dsi_encoder, base.base);
-+}
-+#define host_to_dsi(host) container_of(host, struct vc4_dsi, dsi_host)
-+
-+/* VC4 DSI connector KMS struct */
-+struct vc4_dsi_connector {
-+ struct drm_connector base;
-+ struct vc4_dsi *dsi;
-+
-+ /* Since the connector is attached to just the one encoder,
-+ * this is the reference to it so we can do the best_encoder()
-+ * hook.
-+ */
-+ struct drm_encoder *encoder;
-+};
-+
-+static inline struct vc4_dsi_connector *
-+to_vc4_dsi_connector(struct drm_connector *connector)
-+{
-+ return container_of(connector, struct vc4_dsi_connector, base);
-+}
-+
-+static const struct debugfs_reg32 dsi0_regs[] = {
-+ VC4_DEBUG_REG(DSI0_CTRL),
-+ VC4_DEBUG_REG(DSI0_STAT),
-+ VC4_DEBUG_REG(DSI0_DISP0_CTRL),
-+ VC4_DEBUG_REG(DSI0_DISP1_CTRL),
-+ VC4_DEBUG_REG(DSI0_PHYC),
-+ VC4_DEBUG_REG(DSI0_STAT),
-+ VC4_DEBUG_REG(DSI0_HS_CLT0),
-+ VC4_DEBUG_REG(DSI0_HS_CLT1),
-+ VC4_DEBUG_REG(DSI0_HS_CLT2),
-+ VC4_DEBUG_REG(DSI0_HS_DLT3),
-+ VC4_DEBUG_REG(DSI0_HS_DLT4),
-+ VC4_DEBUG_REG(DSI0_HS_DLT5),
-+ VC4_DEBUG_REG(DSI0_HS_DLT6),
-+ VC4_DEBUG_REG(DSI0_HS_DLT7),
-+ VC4_DEBUG_REG(DSI0_PHY_AFEC0),
-+ VC4_DEBUG_REG(DSI0_PHY_AFEC1),
-+ VC4_DEBUG_REG(DSI0_ID),
-+};
-+
-+static const struct debugfs_reg32 dsi1_regs[] = {
-+ VC4_DEBUG_REG(DSI1_CTRL),
-+ VC4_DEBUG_REG(DSI1_STAT),
-+ VC4_DEBUG_REG(DSI1_DISP0_CTRL),
-+ VC4_DEBUG_REG(DSI1_DISP1_CTRL),
-+ VC4_DEBUG_REG(DSI1_PHYC),
-+ VC4_DEBUG_REG(DSI1_STAT),
-+ VC4_DEBUG_REG(DSI1_HS_CLT0),
-+ VC4_DEBUG_REG(DSI1_HS_CLT1),
-+ VC4_DEBUG_REG(DSI1_HS_CLT2),
-+ VC4_DEBUG_REG(DSI1_HS_DLT3),
-+ VC4_DEBUG_REG(DSI1_HS_DLT4),
-+ VC4_DEBUG_REG(DSI1_HS_DLT5),
-+ VC4_DEBUG_REG(DSI1_HS_DLT6),
-+ VC4_DEBUG_REG(DSI1_HS_DLT7),
-+ VC4_DEBUG_REG(DSI1_PHY_AFEC0),
-+ VC4_DEBUG_REG(DSI1_PHY_AFEC1),
-+ VC4_DEBUG_REG(DSI1_ID),
-+};
-+
-+static void vc4_dsi_dump_regs(struct vc4_dsi *dsi, const char *prefix)
-+{
-+ if (dsi->port == 0) {
-+ vc4_dump_regs32(dsi0_regs, ARRAY_SIZE(dsi0_regs), dsi->regs,
-+ prefix);
-+ } else {
-+ vc4_dump_regs32(dsi1_regs, ARRAY_SIZE(dsi1_regs), dsi->regs,
-+ prefix);
-+ }
-+}
-+
-+#ifdef CONFIG_DEBUG_FS
-+int vc4_dsi_debugfs_regs(struct seq_file *m, void *number)
-+{
-+ struct drm_info_node *node = (struct drm_info_node *)m->private;
-+ struct drm_device *dev = node->minor->dev;
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ struct vc4_dsi *dsi;
-+ int port = (uintptr_t)number;
-+
-+ if (port == 0) {
-+ dsi = vc4->dsi0;
-+ debugfs_print_regs32(m, dsi0_regs, ARRAY_SIZE(dsi0_regs),
-+ dsi->regs, "");
-+ } else {
-+ dsi = vc4->dsi1;
-+ debugfs_print_regs32(m, dsi1_regs, ARRAY_SIZE(dsi1_regs),
-+ dsi->regs, "");
-+ }
-+
-+ return 0;
-+}
-+#endif
-+
-+static enum drm_connector_status
-+vc4_dsi_connector_detect(struct drm_connector *connector, bool force)
-+{
-+ struct vc4_dsi_connector *vc4_connector =
-+ to_vc4_dsi_connector(connector);
-+ struct vc4_dsi *dsi = vc4_connector->dsi;
-+
-+ if (dsi->panel)
-+ return connector_status_connected;
-+ else
-+ return connector_status_disconnected;
-+}
-+
-+static void vc4_dsi_connector_destroy(struct drm_connector *connector)
-+{
-+ drm_connector_unregister(connector);
-+ drm_connector_cleanup(connector);
-+}
-+
-+static int vc4_dsi_connector_get_modes(struct drm_connector *connector)
-+{
-+ struct vc4_dsi_connector *vc4_connector =
-+ to_vc4_dsi_connector(connector);
-+ struct vc4_dsi *dsi = vc4_connector->dsi;
-+
-+ if (dsi->panel)
-+ return drm_panel_get_modes(dsi->panel);
-+
-+ return 0;
-+}
-+
-+static struct drm_encoder *
-+vc4_dsi_connector_best_encoder(struct drm_connector *connector)
-+{
-+ struct vc4_dsi_connector *dsi_connector =
-+ to_vc4_dsi_connector(connector);
-+ return dsi_connector->encoder;
-+}
-+
-+static const struct drm_connector_funcs vc4_dsi_connector_funcs = {
-+ .dpms = drm_atomic_helper_connector_dpms,
-+ .detect = vc4_dsi_connector_detect,
-+ .fill_modes = drm_helper_probe_single_connector_modes,
-+ .destroy = vc4_dsi_connector_destroy,
-+ .reset = drm_atomic_helper_connector_reset,
-+ .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
-+ .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
-+};
-+
-+static const struct drm_connector_helper_funcs vc4_dsi_connector_helper_funcs = {
-+ .get_modes = vc4_dsi_connector_get_modes,
-+ .best_encoder = vc4_dsi_connector_best_encoder,
-+};
-+
-+static struct drm_connector *vc4_dsi_connector_init(struct drm_device *dev,
-+ struct vc4_dsi *dsi)
-+{
-+ struct drm_connector *connector = NULL;
-+ struct vc4_dsi_connector *dsi_connector;
-+ int ret = 0;
-+
-+ dsi_connector = devm_kzalloc(dev->dev, sizeof(*dsi_connector),
-+ GFP_KERNEL);
-+ if (!dsi_connector) {
-+ ret = -ENOMEM;
-+ goto fail;
-+ }
-+ connector = &dsi_connector->base;
-+
-+ dsi_connector->encoder = dsi->encoder;
-+ dsi_connector->dsi = dsi;
-+
-+ drm_connector_init(dev, connector, &vc4_dsi_connector_funcs,
-+ DRM_MODE_CONNECTOR_DSI);
-+ drm_connector_helper_add(connector, &vc4_dsi_connector_helper_funcs);
-+
-+ connector->polled = 0;
-+ connector->interlace_allowed = 0;
-+ connector->doublescan_allowed = 0;
-+
-+ drm_mode_connector_attach_encoder(connector, dsi->encoder);
-+
-+ return connector;
-+
-+ fail:
-+ if (connector)
-+ vc4_dsi_connector_destroy(connector);
-+
-+ return ERR_PTR(ret);
-+}
-+
-+static void vc4_dsi_encoder_destroy(struct drm_encoder *encoder)
-+{
-+ drm_encoder_cleanup(encoder);
-+}
-+
-+static const struct drm_encoder_funcs vc4_dsi_encoder_funcs = {
-+ .destroy = vc4_dsi_encoder_destroy,
-+};
-+
-+static void vc4_dsi_latch_ulps(struct vc4_dsi *dsi, bool latch)
-+{
-+ u32 afec0 = DSI_PORT_READ(PHY_AFEC0);
-+
-+ if (latch)
-+ afec0 |= DSI_PORT_BIT(PHY_AFEC0_LATCH_ULPS);
-+ else
-+ afec0 &= ~DSI_PORT_BIT(PHY_AFEC0_LATCH_ULPS);
-+
-+ DSI_PORT_WRITE(PHY_AFEC0, afec0);
-+}
-+
-+/* Enters or exits Ultra Low Power State. */
-+static void vc4_dsi_ulps(struct vc4_dsi *dsi, bool ulps)
-+{
-+ u32 phyc_ulps = (DSI_PORT_BIT(PHYC_CLANE_ULPS) |
-+ DSI_PHYC_DLANE0_ULPS |
-+ (dsi->lanes > 1 ? DSI_PHYC_DLANE1_ULPS : 0) |
-+ (dsi->lanes > 2 ? DSI_PHYC_DLANE2_ULPS : 0) |
-+ (dsi->lanes > 3 ? DSI_PHYC_DLANE3_ULPS : 0));
-+ u32 stat_ulps = (DSI1_STAT_PHY_CLOCK_ULPS |
-+ DSI1_STAT_PHY_D0_ULPS |
-+ (dsi->lanes > 1 ? DSI1_STAT_PHY_D1_ULPS : 0) |
-+ (dsi->lanes > 2 ? DSI1_STAT_PHY_D2_ULPS : 0) |
-+ (dsi->lanes > 3 ? DSI1_STAT_PHY_D3_ULPS : 0));
-+ u32 stat_stop = (DSI1_STAT_PHY_CLOCK_STOP |
-+ DSI1_STAT_PHY_D0_STOP |
-+ (dsi->lanes > 1 ? DSI1_STAT_PHY_D1_STOP : 0) |
-+ (dsi->lanes > 2 ? DSI1_STAT_PHY_D2_STOP : 0) |
-+ (dsi->lanes > 3 ? DSI1_STAT_PHY_D3_STOP : 0));
-+ int ret;
-+
-+ DSI_PORT_WRITE(STAT, stat_ulps);
-+ DSI_PORT_WRITE(PHYC, DSI_PORT_READ(PHYC) | phyc_ulps);
-+ ret = wait_for((DSI_PORT_READ(STAT) & stat_ulps) == stat_ulps, 20);
-+ if (ret) {
-+ dev_warn(&dsi->pdev->dev,
-+ "Timeout waiting for DSI ULPS entry: STAT 0x%08x",
-+ DSI_PORT_READ(STAT));
-+ DSI_PORT_WRITE(PHYC, DSI_PORT_READ(PHYC) & ~phyc_ulps);
-+ vc4_dsi_latch_ulps(dsi, false);
-+ return;
-+ }
-+
-+ /* The DSI module can't be disabled while the module is
-+ * generating ULPS state. So, to be able to disable the
-+ * module, we have the AFE latch the ULPS state and continue
-+ * on to having the module enter STOP.
-+ */
-+ vc4_dsi_latch_ulps(dsi, ulps);
-+
-+ DSI_PORT_WRITE(STAT, stat_stop);
-+ DSI_PORT_WRITE(PHYC, DSI_PORT_READ(PHYC) & ~phyc_ulps);
-+ ret = wait_for((DSI_PORT_READ(STAT) & stat_stop) == stat_stop, 20);
-+ if (ret) {
-+ dev_warn(&dsi->pdev->dev,
-+ "Timeout waiting for DSI STOP entry: STAT 0x%08x",
-+ DSI_PORT_READ(STAT));
-+ DSI_PORT_WRITE(PHYC, DSI_PORT_READ(PHYC) & ~phyc_ulps);
-+ return;
-+ }
-+}
-+
-+static uint32_t
-+dsi_hs_timing(u32 ui_ns, u32 ns, u32 ui)
-+{
-+ /* The HS timings have to be rounded up to a multiple of 8
-+ * because we're using the byte clock.
-+ */
-+ return roundup(ui + DIV_ROUND_UP(ns, ui_ns), 8);
-+}
-+
-+/* ESC always runs at 100Mhz. */
-+#define ESC_TIME_NS 10
-+
-+static uint32_t
-+dsi_esc_timing(u32 ns)
-+{
-+ return DIV_ROUND_UP(ns, ESC_TIME_NS);
-+}
-+
-+static void vc4_dsi_encoder_disable(struct drm_encoder *encoder)
-+{
-+ struct vc4_dsi_encoder *vc4_encoder = to_vc4_dsi_encoder(encoder);
-+ struct vc4_dsi *dsi = vc4_encoder->dsi;
-+
-+ drm_panel_disable(dsi->panel);
-+
-+ if (!dsi->use_firmware_setup)
-+ vc4_dsi_ulps(dsi, true);
-+
-+ drm_panel_unprepare(dsi->panel);
-+
-+ if (dsi->use_firmware_setup) {
-+ /* Since we're using the firmware setup and aren't
-+ * communicating with the panel to bring the link
-+ * down, we need to just keep the clocks and DSI
-+ * module running.
-+ */
-+ } else {
-+ clk_disable_unprepare(dsi->pll_phy_clock);
-+ clk_disable_unprepare(dsi->escape_clock);
-+ clk_disable_unprepare(dsi->pixel_clock);
-+ }
-+}
-+
-+static void vc4_dsi_encoder_enable(struct drm_encoder *encoder)
-+{
-+ struct drm_display_mode *mode = &encoder->crtc->mode;
-+ struct vc4_dsi_encoder *vc4_encoder = to_vc4_dsi_encoder(encoder);
-+ struct vc4_dsi *dsi = vc4_encoder->dsi;
-+ struct device *dev = &dsi->pdev->dev;
-+ uint32_t format = 0, divider = 0;
-+ bool debug_dump_regs = false;
-+ unsigned long hs_clock;
-+ uint32_t ui_ns;
-+ /* Minimum LP state duration in escape clock cycles. */
-+ uint32_t lpx = dsi_esc_timing(60);
-+ uint32_t phyc;
-+ int ret;
-+
-+ ret = drm_panel_prepare(dsi->panel);
-+ if (ret) {
-+ DRM_ERROR("Panel failed to prepare\n");
-+ return;
-+ }
-+
-+ if (debug_dump_regs)
-+ vc4_dsi_dump_regs(dsi, "DSI before: ");
-+
-+ /* XXX */
-+ if (!dsi->use_firmware_setup) {
-+ ret = clk_set_rate(dsi->pll_phy_clock, 2020000000 / 3);
-+ if (ret)
-+ dev_err(&dsi->pdev->dev, "Failed to set phy clock: %d\n", ret);
-+ dev_info(&dsi->pdev->dev, "Tried to set clock to: %d\n", 2000000000 / 3);
-+
-+ ret = clk_prepare_enable(dsi->escape_clock);
-+ if (ret) {
-+ DRM_ERROR("Failed to turn on DSI escape clock: %d\n", ret);
-+ return;
-+ }
-+
-+ ret = clk_prepare_enable(dsi->pll_phy_clock);
-+ if (ret) {
-+ DRM_ERROR("Failed to turn on DSI PLL: %d\n", ret);
-+ return;
-+ }
-+
-+ ret = clk_set_rate(dsi->pixel_clock, mode->clock * 1000);
-+ if (ret)
-+ dev_err(dev, "Failed to set pixel clock: %d\n", ret);
-+ dev_info(&dsi->pdev->dev, "Tried to set pixel clock to: %d\n", mode->clock * 1000);
-+
-+ ret = clk_prepare_enable(dsi->pixel_clock);
-+ if (ret) {
-+ DRM_ERROR("Failed to turn on DSI pixel clock: %d\n", ret);
-+ return;
-+ }
-+ }
-+
-+ hs_clock = clk_get_rate(dsi->pll_phy_clock);
-+
-+ /* Reset the DSI and all its fifos. */
-+ if (dsi->port == 0) {
-+ DSI_PORT_WRITE(CTRL,
-+ DSI_CTRL_SOFT_RESET_CFG |
-+ DSI0_CTRL_RESET_FIFOS);
-+ } else {
-+ DSI_PORT_WRITE(CTRL,
-+ DSI_CTRL_SOFT_RESET_CFG |
-+ DSI1_CTRL_RESET_FIFOS);
-+ }
-+
-+ DSI_PORT_WRITE(CTRL,
-+ DSI_CTRL_HSDT_EOT_DISABLE |
-+ DSI_CTRL_RX_LPDT_EOT_DISABLE);
-+
-+ switch (dsi->format) {
-+ case MIPI_DSI_FMT_RGB888:
-+ format = DSI_PFORMAT_RGB888;
-+ divider = 24 / dsi->lanes;
-+ break;
-+ case MIPI_DSI_FMT_RGB666:
-+ format = DSI_PFORMAT_RGB666;
-+ divider = 24 / dsi->lanes;
-+ break;
-+ case MIPI_DSI_FMT_RGB666_PACKED:
-+ format = DSI_PFORMAT_RGB666_PACKED;
-+ divider = 18 / dsi->lanes;
-+ break;
-+ case MIPI_DSI_FMT_RGB565:
-+ format = DSI_PFORMAT_RGB565;
-+ divider = 16 / dsi->lanes;
-+ break;
-+ }
-+
-+ /* Set AFE CTR00/CTR1 to release powerdown of analog. */
-+ if (dsi->port == 0) {
-+ u32 afec0 = (VC4_SET_FIELD(7, DSI_PHY_AFEC0_PTATADJ) |
-+ VC4_SET_FIELD(7, DSI_PHY_AFEC0_CTATADJ));
-+
-+ if (dsi->lanes < 2)
-+ afec0 |= DSI0_PHY_AFEC0_PD_DLANE1;
-+
-+ if (!(dsi->mode_flags & MIPI_DSI_MODE_VIDEO))
-+ afec0 |= DSI0_PHY_AFEC0_RESET;
-+
-+ DSI_PORT_WRITE(PHY_AFEC0, afec0);
-+
-+ DSI_PORT_WRITE(PHY_AFEC1,
-+ VC4_SET_FIELD(6, DSI0_PHY_AFEC1_IDR_DLANE1) |
-+ VC4_SET_FIELD(6, DSI0_PHY_AFEC1_IDR_DLANE0) |
-+ VC4_SET_FIELD(6, DSI0_PHY_AFEC1_IDR_CLANE));
-+ } else {
-+ u32 afec0 = (VC4_SET_FIELD(7, DSI_PHY_AFEC0_PTATADJ) |
-+ VC4_SET_FIELD(7, DSI_PHY_AFEC0_CTATADJ) |
-+ VC4_SET_FIELD(6, DSI1_PHY_AFEC0_IDR_CLANE) |
-+ VC4_SET_FIELD(6, DSI1_PHY_AFEC0_IDR_DLANE0) |
-+ VC4_SET_FIELD(6, DSI1_PHY_AFEC0_IDR_DLANE1) |
-+ VC4_SET_FIELD(6, DSI1_PHY_AFEC0_IDR_DLANE2) |
-+ VC4_SET_FIELD(6, DSI1_PHY_AFEC0_IDR_DLANE3));
-+
-+ if (dsi->lanes < 4)
-+ afec0 |= DSI1_PHY_AFEC0_PD_DLANE3;
-+ if (dsi->lanes < 3)
-+ afec0 |= DSI1_PHY_AFEC0_PD_DLANE2;
-+ if (dsi->lanes < 2)
-+ afec0 |= DSI1_PHY_AFEC0_PD_DLANE1;
-+
-+ if (!(dsi->mode_flags & MIPI_DSI_MODE_VIDEO))
-+ afec0 |= DSI1_PHY_AFEC0_RESET;
-+
-+ DSI_PORT_WRITE(PHY_AFEC0, afec0);
-+
-+ DSI_PORT_WRITE(PHY_AFEC1, 0);
-+ }
-+
-+ /* How many ns one DSI unit interval is. Note that the clock
-+ * is DDR, so there's an extra divide by 2.
-+ */
-+ ui_ns = DIV_ROUND_UP(500000000, hs_clock);
-+
-+ DSI_PORT_WRITE(HS_CLT0,
-+ VC4_SET_FIELD(dsi_hs_timing(ui_ns, 262, 0),
-+ DSI_HS_CLT0_CZERO) |
-+ VC4_SET_FIELD(dsi_hs_timing(ui_ns, 0, 8),
-+ DSI_HS_CLT0_CPRE) |
-+ VC4_SET_FIELD(dsi_hs_timing(ui_ns, 38, 0),
-+ DSI_HS_CLT0_CPREP));
-+
-+ DSI_PORT_WRITE(HS_CLT1,
-+ VC4_SET_FIELD(dsi_hs_timing(ui_ns, 60, 0),
-+ DSI_HS_CLT1_CTRAIL) |
-+ VC4_SET_FIELD(dsi_hs_timing(ui_ns, 60, 52),
-+ DSI_HS_CLT1_CPOST));
-+
-+ DSI_PORT_WRITE(HS_CLT2,
-+ VC4_SET_FIELD(dsi_hs_timing(ui_ns, 1000000, 0),
-+ DSI_HS_CLT2_WUP));
-+
-+ DSI_PORT_WRITE(HS_DLT3,
-+ VC4_SET_FIELD(dsi_hs_timing(ui_ns, 100, 0),
-+ DSI_HS_DLT3_EXIT) |
-+ VC4_SET_FIELD(dsi_hs_timing(ui_ns, 105, 6),
-+ DSI_HS_DLT3_ZERO) |
-+ VC4_SET_FIELD(dsi_hs_timing(ui_ns, 40, 4),
-+ DSI_HS_DLT3_PRE));
-+
-+ DSI_PORT_WRITE(HS_DLT4,
-+ VC4_SET_FIELD(dsi_hs_timing(ui_ns, lpx * ESC_TIME_NS, 0),
-+ DSI_HS_DLT4_LPX) |
-+ VC4_SET_FIELD(max(dsi_hs_timing(ui_ns, 0, 8),
-+ dsi_hs_timing(ui_ns, 60, 4)),
-+ DSI_HS_DLT4_TRAIL) |
-+ VC4_SET_FIELD(0, DSI_HS_DLT4_ANLAT));
-+
-+ DSI_PORT_WRITE(HS_DLT5, VC4_SET_FIELD(dsi_hs_timing(ui_ns, 1000, 5000),
-+ DSI_HS_DLT5_INIT));
-+
-+ DSI_PORT_WRITE(HS_DLT6,
-+ VC4_SET_FIELD(lpx * 5, DSI_HS_DLT6_TA_GET) |
-+ VC4_SET_FIELD(lpx, DSI_HS_DLT6_TA_SURE) |
-+ VC4_SET_FIELD(lpx * 4, DSI_HS_DLT6_TA_GO) |
-+ VC4_SET_FIELD(lpx, DSI_HS_DLT6_LP_LPX));
-+
-+ DSI_PORT_WRITE(HS_DLT7,
-+ VC4_SET_FIELD(dsi_esc_timing(1000000),
-+ DSI_HS_DLT7_LP_WUP));
-+
-+ /* Define EOT PKT in EOT reg. */
-+
-+ phyc = (DSI_PHYC_DLANE0_ENABLE |
-+ (dsi->lanes >= 2 ? DSI_PHYC_DLANE1_ENABLE : 0) |
-+ (dsi->lanes >= 3 ? DSI_PHYC_DLANE2_ENABLE : 0) |
-+ (dsi->lanes >= 4 ? DSI_PHYC_DLANE3_ENABLE : 0) |
-+ (dsi->port == 0 ?
-+ VC4_SET_FIELD(lpx - 1, DSI0_PHYC_ESC_CLK_LPDT) :
-+ VC4_SET_FIELD(lpx - 1, DSI1_PHYC_ESC_CLK_LPDT)) |
-+ DSI_PORT_BIT(PHYC_CLANE_ENABLE));
-+
-+ DSI_PORT_WRITE(CTRL,
-+ DSI_PORT_READ(CTRL) |
-+ DSI_CTRL_CAL_BYTE);
-+
-+ /* HS timeout in HS clock cycles: disabled. */
-+ DSI_PORT_WRITE(HSTX_TO_CNT, 0);
-+ /* LP receive timeout in HS clocks. */
-+ DSI_PORT_WRITE(LPRX_TO_CNT, 0xffffff);
-+ /* Bus turnaround timeout */
-+ DSI_PORT_WRITE(TA_TO_CNT, 100000);
-+ /* Display reset sequence timeout */
-+ DSI_PORT_WRITE(TA_TO_CNT, 100000);
-+
-+ if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO) {
-+ DSI_PORT_WRITE(DISP0_CTRL,
-+ VC4_SET_FIELD(divider, DSI_DISP0_PIX_CLK_DIV) |
-+ VC4_SET_FIELD(format, DSI_DISP0_PFORMAT) |
-+ VC4_SET_FIELD(DSI_DISP0_LP_STOP_PERFRAME,
-+ DSI_DISP0_LP_STOP_CTRL) |
-+ DSI_DISP0_ST_END |
-+ DSI_DISP0_ENABLE);
-+ } else {
-+ DSI_PORT_WRITE(DISP0_CTRL,
-+ DSI_DISP0_COMMAND_MODE |
-+ DSI_DISP0_ENABLE);
-+ }
-+
-+ /* Set up DISP1 for transferring long command payloads through
-+ * the pixfifo.
-+ */
-+ DSI_PORT_WRITE(DISP1_CTRL,
-+ VC4_SET_FIELD(DSI_DISP1_PFORMAT_32BIT_LE,
-+ DSI_DISP1_PFORMAT) |
-+ DSI_DISP1_ENABLE);
-+
-+ if (!(dsi->mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS))
-+ phyc |= DSI_PORT_BIT(PHYC_HS_CLK_CONTINUOUS);
-+
-+ DSI_PORT_WRITE(PHYC, phyc);
-+
-+ /* Ungate the block. */
-+ if (dsi->port == 0)
-+ DSI_PORT_WRITE(CTRL, DSI_PORT_READ(CTRL) | DSI0_CTRL_CTRL0);
-+ else {
-+ DSI_PORT_WRITE(CTRL, DSI_PORT_READ(CTRL) | DSI1_CTRL_EN);
-+ }
-+
-+ if (!dsi->use_firmware_setup)
-+ vc4_dsi_ulps(dsi, false);
-+
-+ if (debug_dump_regs)
-+ vc4_dsi_dump_regs(dsi, "DSI after: ");
-+
-+ ret = drm_panel_enable(dsi->panel);
-+ if (ret) {
-+ DRM_ERROR("Panel failed to enable\n");
-+ drm_panel_unprepare(dsi->panel);
-+ return;
-+ }
-+}
-+
-+static ssize_t vc4_dsi_host_transfer(struct mipi_dsi_host *host,
-+ const struct mipi_dsi_msg *msg)
-+{
-+ struct vc4_dsi *dsi = host_to_dsi(host);
-+ struct mipi_dsi_packet packet;
-+ u32 pkth = 0, pktc = 0;
-+ int i, ret;
-+ bool is_long = mipi_dsi_packet_format_is_long(msg->type);
-+ u32 cmd_fifo_len = 0, pix_fifo_len = 0;
-+
-+ mipi_dsi_create_packet(&packet, msg);
-+ pr_err("DSI host xfer %db, %s\n",
-+ packet.payload_length,
-+ is_long ? "long" : "short");
-+
-+ pkth |= VC4_SET_FIELD(packet.header[0], DSI_TXPKT1H_BC_DT);
-+ pkth |= VC4_SET_FIELD(packet.header[1] |
-+ (packet.header[2] << 8),
-+ DSI_TXPKT1H_BC_PARAM);
-+ if (is_long) {
-+ /* Divide data across the various FIFOs we have available.
-+ * The command FIFO takes byte-oriented data, but is of
-+ * limited size. The pixel FIFO (never actually used for
-+ * pixel data in reality) is word oriented, and substantially
-+ * larger. So, we use the pixel FIFO for most of the data,
-+ * sending the residual bytes in the command FIFO at the start.
-+ *
-+ * With this arrangement, the command FIFO will never get full.
-+ */
-+ cmd_fifo_len = packet.payload_length % DSI_PIX_FIFO_WIDTH;
-+ pix_fifo_len = ((packet.payload_length - cmd_fifo_len) /
-+ DSI_PIX_FIFO_WIDTH);
-+
-+ WARN_ON_ONCE(pix_fifo_len >= DSI_PIX_FIFO_DEPTH);
-+
-+ pkth |= VC4_SET_FIELD(cmd_fifo_len, DSI_TXPKT1H_BC_CMDFIFO);
-+ }
-+
-+ if (msg->rx_len) {
-+ pktc |= VC4_SET_FIELD(DSI_TXPKT1C_CMD_CTRL_RX,
-+ DSI_TXPKT1C_CMD_CTRL);
-+ } else {
-+ pktc |= VC4_SET_FIELD(DSI_TXPKT1C_CMD_CTRL_TX,
-+ DSI_TXPKT1C_CMD_CTRL);
-+ }
-+
-+ dev_info(&dsi->pdev->dev, "FIFO setup: %d, %d\n",
-+ cmd_fifo_len, pix_fifo_len);
-+
-+ for (i = 0; i < cmd_fifo_len; i++)
-+ DSI_PORT_WRITE(TXPKT_CMD_FIFO, packet.payload[i]);
-+ for (i = 0; i < pix_fifo_len; i++) {
-+ const uint8_t *pix = packet.payload + cmd_fifo_len + i * 4;
-+ DSI_PORT_WRITE(TXPKT_PIX_FIFO,
-+ pix[0] |
-+ pix[1] << 8 |
-+ pix[2] << 16 |
-+ pix[3] << 24);
-+ }
-+
-+ if (msg->flags & MIPI_DSI_MSG_USE_LPM)
-+ pktc |= DSI_TXPKT1C_CMD_MODE_LP;
-+ if (is_long)
-+ pktc |= DSI_TXPKT1C_CMD_TYPE_LONG;
-+
-+ /* Send one copy of the packet. Larger repeats are used for pixel
-+ * data in command mode.
-+ */
-+ pktc |= VC4_SET_FIELD(1, DSI_TXPKT1C_CMD_REPEAT);
-+
-+ pktc |= DSI_TXPKT1C_CMD_EN;
-+ if (pix_fifo_len) {
-+ pktc |= VC4_SET_FIELD(DSI_TXPKT1C_DISPLAY_NO_SECONDARY,
-+ DSI_TXPKT1C_DISPLAY_NO);
-+ } else {
-+ pktc |= VC4_SET_FIELD(DSI_TXPKT1C_DISPLAY_NO_SHORT,
-+ DSI_TXPKT1C_DISPLAY_NO);
-+ }
-+
-+ /* Enable the appropriate interrupt for the transfer completion. */
-+ dsi->xfer_result = 0;
-+ reinit_completion(&dsi->xfer_completion);
-+ DSI_PORT_WRITE(INT_STAT, DSI1_INT_TXPKT1_DONE | DSI1_INT_PHY_DIR_RTF);
-+ if (msg->rx_len) {
-+ DSI_PORT_WRITE(INT_EN, (DSI1_INTERRUPTS_ALWAYS_ENABLED |
-+ DSI1_INT_PHY_DIR_RTF));
-+ } else {
-+ DSI_PORT_WRITE(INT_EN, (DSI1_INTERRUPTS_ALWAYS_ENABLED |
-+ DSI1_INT_TXPKT1_DONE));
-+ }
-+
-+ /* Send the packet. */
-+ DSI_PORT_WRITE(TXPKT1H, pkth);
-+ DSI_PORT_WRITE(TXPKT1C, pktc);
-+
-+ if (!wait_for_completion_timeout(&dsi->xfer_completion,
-+ msecs_to_jiffies(100))) {
-+ u32 stat = DSI_PORT_READ(STAT);
-+
-+ dev_err(&dsi->pdev->dev, "transfer interrupt wait timeout");
-+ dev_err(&dsi->pdev->dev, "INT_STAT: 0x%08x, STAT: 0x%08x\n",
-+ DSI_PORT_READ(INT_STAT), stat);
-+
-+ if (stat & DSI1_STAT_TXPKT1_DONE) {
-+ dev_info(&dsi->pdev->dev,
-+ "STAT reports DONE, though.\n");
-+ ret = 0;
-+ } else {
-+ ret = -ETIMEDOUT;
-+ }
-+ } else {
-+ ret = dsi->xfer_result;
-+ }
-+
-+ DSI_PORT_WRITE(INT_EN, DSI1_INTERRUPTS_ALWAYS_ENABLED);
-+ if (ret)
-+ goto reset_fifo_and_return;
-+
-+ if (ret == 0 && msg->rx_len) {
-+ u32 rxpkt1h = DSI_PORT_READ(RXPKT1H);
-+ u8 *msg_rx = msg->rx_buf;
-+
-+ if (rxpkt1h & DSI_RXPKT1H_PKT_TYPE_LONG) {
-+ u32 rxlen = VC4_GET_FIELD(rxpkt1h, DSI_RXPKT1H_BC_PARAM);
-+
-+ if (rxlen != msg->rx_len) {
-+ DRM_ERROR("DSI returned %db, expecting %db\n",
-+ rxlen, msg->rx_len);
-+ ret = -ENXIO;
-+ goto reset_fifo_and_return;
-+ }
-+
-+ for (i = 0; i < msg->rx_len; i++)
-+ msg_rx[i] = DSI_READ(DSI1_RXPKT_FIFO);
-+ } else {
-+ /* XXX: AWER */
-+
-+ msg_rx[0] = VC4_GET_FIELD(rxpkt1h,
-+ DSI_RXPKT1H_SHORT_0);
-+ if (msg->rx_len > 1) {
-+ msg_rx[1] = VC4_GET_FIELD(rxpkt1h,
-+ DSI_RXPKT1H_SHORT_1);
-+ }
-+ }
-+ }
-+
-+ return ret;
-+
-+reset_fifo_and_return:
-+ DRM_ERROR("DSI TRANSFER failed, resetting: %d\n", ret);
-+
-+ DSI_PORT_WRITE(TXPKT1C, DSI_PORT_READ(TXPKT1C) & ~DSI_TXPKT1C_CMD_EN);
-+ udelay(1);
-+ if (dsi->port == 0) {
-+ DSI_PORT_WRITE(CTRL,
-+ DSI_PORT_READ(CTRL) | DSI0_CTRL_RESET_FIFOS);
-+ } else {
-+ DSI_PORT_WRITE(CTRL,
-+ DSI_PORT_READ(CTRL) | DSI1_CTRL_RESET_FIFOS);
-+ }
-+
-+ DSI_PORT_WRITE(TXPKT1C, 0);
-+ DSI_PORT_WRITE(INT_EN, DSI1_INTERRUPTS_ALWAYS_ENABLED);
-+
-+
-+ return ret;
-+}
-+
-+static int vc4_dsi_host_attach(struct mipi_dsi_host *host,
-+ struct mipi_dsi_device *device)
-+{
-+ struct vc4_dsi *dsi = host_to_dsi(host);
-+
-+ dsi->lanes = device->lanes;
-+ dsi->channel = device->channel;
-+ dsi->format = device->format;
-+ dsi->mode_flags = device->mode_flags;
-+
-+ if (!(dsi->mode_flags & MIPI_DSI_MODE_VIDEO)) {
-+ dev_err(&dsi->pdev->dev,
-+ "Only VIDEO mode panels supported currently.\n");
-+ return 0;
-+ }
-+
-+ dsi->panel = of_drm_find_panel(device->dev.of_node);
-+ if (dsi->panel)
-+ return drm_panel_attach(dsi->panel, dsi->connector);
-+
-+ drm_helper_hpd_irq_event(dsi->connector->dev);
-+
-+ return 0;
-+}
-+
-+static int vc4_dsi_host_detach(struct mipi_dsi_host *host,
-+ struct mipi_dsi_device *device)
-+{
-+ struct vc4_dsi *dsi = host_to_dsi(host);
-+
-+ if (dsi->panel) {
-+ int ret = drm_panel_detach(dsi->panel);
-+ if (ret)
-+ return ret;
-+
-+ dsi->panel = NULL;
-+ }
-+
-+ drm_helper_hpd_irq_event(dsi->connector->dev);
-+
-+ return 0;
-+}
-+
-+static const struct mipi_dsi_host_ops vc4_dsi_host_ops = {
-+ .attach = vc4_dsi_host_attach,
-+ .detach = vc4_dsi_host_detach,
-+ .transfer = vc4_dsi_host_transfer,
-+};
-+
-+static const struct drm_encoder_helper_funcs vc4_dsi_encoder_helper_funcs = {
-+ .disable = vc4_dsi_encoder_disable,
-+ .enable = vc4_dsi_encoder_enable,
-+};
-+
-+static const struct of_device_id vc4_dsi_dt_match[] = {
-+ { .compatible = "brcm,bcm2835-dsi0", (void *)(uintptr_t)0 },
-+ { .compatible = "brcm,bcm2835-dsi1", (void *)(uintptr_t)1 },
-+ {}
-+};
-+
-+static long vc4_dsi_byte_clock_round_rate(struct clk_hw *hw, unsigned long rate,
-+ unsigned long *parent_rate)
-+{
-+ return *parent_rate / 8;
-+}
-+
-+static unsigned long vc4_dsi_byte_clock_get_rate(struct clk_hw *hw,
-+ unsigned long parent_rate)
-+{
-+ return parent_rate / 8;
-+}
-+
-+static int vc4_dsi_byte_clock_set_rate(struct clk_hw *hw,
-+ unsigned long rate,
-+ unsigned long parent_rate)
-+{
-+ return 0;
-+}
-+
-+/* The byte clock has *no* ops filled. It's always running when the
-+ * PHY is.
-+ */
-+static const struct clk_ops vc4_dsi_byte_clock_ops = {
-+ .recalc_rate = vc4_dsi_byte_clock_get_rate,
-+ .set_rate = vc4_dsi_byte_clock_set_rate,
-+ .round_rate = vc4_dsi_byte_clock_round_rate,
-+};
-+
-+static void dsi_handle_error(struct vc4_dsi *dsi,
-+ irqreturn_t *ret, u32 stat, u32 bit,
-+ const char *type)
-+{
-+ if (!(stat & bit))
-+ return;
-+
-+ DRM_ERROR("DSI%d: %s error\n", dsi->port, type);
-+ *ret = IRQ_HANDLED;
-+}
-+
-+static irqreturn_t vc4_dsi_irq_handler(int irq, void *data)
-+{
-+ struct vc4_dsi *dsi = data;
-+ u32 stat = DSI_PORT_READ(INT_STAT);
-+ irqreturn_t ret = IRQ_NONE;
-+
-+ DSI_PORT_WRITE(INT_STAT, stat);
-+
-+ dsi_handle_error(dsi, &ret, stat,
-+ DSI1_INT_ERR_SYNC_ESC, "LPDT sync");
-+ dsi_handle_error(dsi, &ret, stat,
-+ DSI1_INT_ERR_CONTROL, "data lane 0 sequence");
-+ dsi_handle_error(dsi, &ret, stat,
-+ DSI1_INT_ERR_CONT_LP0, "LP0 contention");
-+ dsi_handle_error(dsi, &ret, stat,
-+ DSI1_INT_ERR_CONT_LP1, "LP1 contention");
-+ dsi_handle_error(dsi, &ret, stat,
-+ DSI1_INT_HSTX_TO, "HSTX timeout");
-+ dsi_handle_error(dsi, &ret, stat,
-+ DSI1_INT_LPRX_TO, "LPRX timeout");
-+ dsi_handle_error(dsi, &ret, stat,
-+ DSI1_INT_TA_TO, "turnaround timeout");
-+ dsi_handle_error(dsi, &ret, stat,
-+ DSI1_INT_PR_TO, "peripheral reset timeout");
-+
-+ if (stat & (DSI1_INT_TXPKT1_DONE | DSI1_INT_PHY_DIR_RTF)) {
-+ complete(&dsi->xfer_completion);
-+ ret = IRQ_HANDLED;
-+ } else if (stat & DSI1_INT_HSTX_TO) {
-+ complete(&dsi->xfer_completion);
-+ dsi->xfer_result = -ETIMEDOUT;
-+ ret = IRQ_HANDLED;
-+ }
-+
-+ return ret;
-+}
-+
-+static int
-+vc4_dsi_init_phy_byte_clock(struct vc4_dsi *dsi)
-+{
-+ struct device *dev = &dsi->pdev->dev;
-+ const char *parent_name = __clk_get_name(dsi->pll_phy_clock);
-+ struct clk_init_data init;
-+ struct clk *clk;
-+
-+ memset(&init, 0, sizeof(init));
-+ init.parent_names = &parent_name;
-+ init.num_parents = 1;
-+ if (dsi->port == 1)
-+ init.name = "dsi1_byte";
-+ else
-+ init.name = "dsi0_byte";
-+ init.ops = &vc4_dsi_byte_clock_ops;
-+ init.flags = 0;
-+
-+ dsi->phy_byte_clock.init = &init;
-+ clk = devm_clk_register(dev, &dsi->phy_byte_clock);
-+ if (IS_ERR(clk))
-+ return PTR_ERR(clk);
-+
-+ /* Use the onecell provider because we may need to expose the
-+ * DDR and DDR2 clocks at some point, which we'd want to put
-+ * in slots 1 and 2.
-+ */
-+ dsi->clk_onecell.clk_num = 1;
-+ dsi->clk_onecell.clks = devm_kcalloc(dev,
-+ dsi->clk_onecell.clk_num,
-+ sizeof(*dsi->clk_onecell.clks),
-+ GFP_KERNEL);
-+ if (!dsi->clk_onecell.clks)
-+ return -ENOMEM;
-+
-+ dsi->clk_onecell.clks[0] = clk;
-+
-+ return of_clk_add_provider(dev->of_node,
-+ of_clk_src_onecell_get,
-+ &dsi->clk_onecell);
-+}
-+
-+static int vc4_dsi_bind(struct device *dev, struct device *master, void *data)
-+{
-+ struct platform_device *pdev = to_platform_device(dev);
-+ struct drm_device *drm = dev_get_drvdata(master);
-+ struct vc4_dev *vc4 = to_vc4_dev(drm);
-+ struct vc4_dsi *dsi;
-+ struct vc4_dsi_encoder *vc4_dsi_encoder;
-+ const struct of_device_id *match;
-+ dma_cap_mask_t dma_mask;
-+ int ret;
-+
-+ dsi = devm_kzalloc(dev, sizeof(*dsi), GFP_KERNEL);
-+ if (!dsi)
-+ return -ENOMEM;
-+
-+ match = of_match_device(vc4_dsi_dt_match, dev);
-+ if (!match)
-+ return -ENODEV;
-+
-+ dsi->port = (uintptr_t)match->data;
-+
-+ vc4_dsi_encoder = devm_kzalloc(dev, sizeof(*vc4_dsi_encoder),
-+ GFP_KERNEL);
-+ if (!vc4_dsi_encoder)
-+ return -ENOMEM;
-+ vc4_dsi_encoder->base.type = VC4_ENCODER_TYPE_DSI1;
-+ vc4_dsi_encoder->dsi = dsi;
-+ dsi->encoder = &vc4_dsi_encoder->base.base;
-+
-+ dsi->pdev = pdev;
-+ dsi->regs = vc4_ioremap_regs(pdev, 0);
-+ if (IS_ERR(dsi->regs))
-+ return PTR_ERR(dsi->regs);
-+
-+ if (DSI_PORT_READ(ID) != DSI_ID_VALUE) {
-+ dev_err(dev, "Port returned 0x%08x for ID instead of 0x%08x\n",
-+ DSI_PORT_READ(ID), DSI_ID_VALUE);
-+ return -ENODEV;
-+ }
-+
-+ if (DSI_PORT_READ(CTRL) == 0) {
-+ dev_info(dev, "DSI not set up by firmware.\n");
-+ return 0;
-+ }
-+
-+ /* Set this flag to indicate that we're relying on boot-time
-+ * DSI state and can't successfully reconfigure DSI yet.
-+ */
-+ dsi->use_firmware_setup = VC4_DSI_USE_FIRMWARE_SETUP;
-+
-+ if (dsi->use_firmware_setup) {
-+ /* Increment references to the various clocks so that
-+ * they stay always enabled and the clock framework
-+ * doesn't disable their parents.
-+ */
-+ ret = clk_prepare_enable(dsi->escape_clock);
-+ if (ret) {
-+ DRM_ERROR("Failed to refcount DSI escape clock: %d\n", ret);
-+ return ret;
-+ }
-+
-+ ret = clk_prepare_enable(dsi->pll_phy_clock);
-+ if (ret) {
-+ DRM_ERROR("Failed to refcount DSI PLL: %d\n", ret);
-+ return ret;
-+ }
-+
-+ ret = clk_prepare_enable(dsi->pixel_clock);
-+ if (ret) {
-+ DRM_ERROR("Failed to refcount pixel clock: %d\n", ret);
-+ return ret;
-+ }
-+ }
-+
-+ /* DSI1 has a broken AXI slave that doesn't respond to writes
-+ * from the ARM. It does handle writes from the DMA engine,
-+ * so set up a channel for talking to it.
-+ */
-+ if (dsi->port == 1) {
-+ dsi->reg_dma_mem = dma_alloc_coherent(dev, 4,
-+ &dsi->reg_dma_paddr,
-+ GFP_KERNEL);
-+ if (!dsi->reg_dma_mem) {
-+ DRM_ERROR("Failed to get DMA memory\n");
-+ return -ENOMEM;
-+ }
-+
-+ dma_cap_zero(dma_mask);
-+ dma_cap_set(DMA_MEMCPY, dma_mask);
-+ dsi->reg_dma_chan = dma_request_channel(dma_mask, NULL, NULL);
-+ if (IS_ERR(dsi->reg_dma_chan)) {
-+ ret = PTR_ERR(dsi->reg_dma_chan);
-+ if (ret != -EPROBE_DEFER)
-+ DRM_ERROR("Failed to get DMA channel: %d\n",
-+ ret);
-+ return ret;
-+ }
-+
-+ /* Get the physical address of the device's registers. The
-+ * struct resource for the regs gives us the bus address
-+ * instead.
-+ */
-+ dsi->reg_paddr = be32_to_cpup(of_get_address(dev->of_node,
-+ 0, NULL, NULL));
-+ }
-+
-+ init_completion(&dsi->xfer_completion);
-+ /* At startup enable error-reporting interrupts and nothing else. */
-+ DSI_PORT_WRITE(INT_EN, DSI1_INTERRUPTS_ALWAYS_ENABLED);
-+ /* Clear any existing interrupt state. */
-+ DSI_PORT_WRITE(INT_STAT, DSI_PORT_READ(INT_STAT));
-+
-+ ret = devm_request_irq(dev, platform_get_irq(pdev, 0),
-+ vc4_dsi_irq_handler, 0, "vc4 dsi", dsi);
-+ if (ret) {
-+ if (ret != -EPROBE_DEFER)
-+ dev_err(dev, "Failed to get interrupt: %d\n", ret);
-+ return ret;
-+ }
-+
-+ dsi->escape_clock = devm_clk_get(dev, "escape");
-+ if (IS_ERR(dsi->escape_clock)) {
-+ ret = PTR_ERR(dsi->escape_clock);
-+ if (ret != -EPROBE_DEFER)
-+ dev_err(dev, "Failed to get escape clock: %d\n", ret);
-+ return ret;
-+ }
-+
-+ dsi->pll_phy_clock = devm_clk_get(dev, "phy");
-+ if (IS_ERR(dsi->pll_phy_clock)) {
-+ ret = PTR_ERR(dsi->pll_phy_clock);
-+ if (ret != -EPROBE_DEFER)
-+ dev_err(dev, "Failed to get phy clock: %d\n", ret);
-+ return ret;
-+ }
-+
-+ dsi->pixel_clock = devm_clk_get(dev, "pixel");
-+ if (IS_ERR(dsi->pixel_clock)) {
-+ ret = PTR_ERR(dsi->pixel_clock);
-+ if (ret != -EPROBE_DEFER)
-+ dev_err(dev, "Failed to get pixel clock: %d\n", ret);
-+ return ret;
-+ }
-+
-+ /* The esc clock rate is supposed to always be 100Mhz. */
-+ ret = clk_set_rate(dsi->escape_clock, 100 * 1000000);
-+ if (ret) {
-+ dev_err(dev, "Failed to set esc clock: %d\n", ret);
-+ return ret;
-+ }
-+
-+ ret = vc4_dsi_init_phy_byte_clock(dsi);
-+ if (ret)
-+ return ret;
-+
-+ if (dsi->port == 1)
-+ vc4->dsi1 = dsi;
-+
-+ drm_encoder_init(drm, dsi->encoder, &vc4_dsi_encoder_funcs,
-+ DRM_MODE_ENCODER_DSI);
-+ drm_encoder_helper_add(dsi->encoder, &vc4_dsi_encoder_helper_funcs);
-+
-+ dsi->connector = vc4_dsi_connector_init(drm, dsi);
-+ if (IS_ERR(dsi->connector)) {
-+ ret = PTR_ERR(dsi->connector);
-+ goto err_destroy_encoder;
-+ }
-+
-+ dsi->dsi_host.ops = &vc4_dsi_host_ops;
-+ dsi->dsi_host.dev = dev;
-+
-+ mipi_dsi_host_register(&dsi->dsi_host);
-+
-+ dev_set_drvdata(dev, dsi);
-+
-+ return 0;
-+
-+err_destroy_encoder:
-+ vc4_dsi_encoder_destroy(dsi->encoder);
-+
-+ return ret;
-+}
-+
-+static void vc4_dsi_unbind(struct device *dev, struct device *master,
-+ void *data)
-+{
-+ struct drm_device *drm = dev_get_drvdata(master);
-+ struct vc4_dev *vc4 = to_vc4_dev(drm);
-+ struct vc4_dsi *dsi = dev_get_drvdata(dev);
-+
-+ vc4_dsi_connector_destroy(dsi->connector);
-+ vc4_dsi_encoder_destroy(dsi->encoder);
-+
-+ mipi_dsi_host_unregister(&dsi->dsi_host);
-+
-+ if (!dsi->use_firmware_setup) {
-+ clk_disable_unprepare(dsi->pll_phy_clock);
-+ clk_disable_unprepare(dsi->escape_clock);
-+ clk_disable_unprepare(dsi->pixel_clock);
-+ }
-+
-+ if (dsi->port == 1)
-+ vc4->dsi1 = NULL;
-+}
-+
-+static const struct component_ops vc4_dsi_ops = {
-+ .bind = vc4_dsi_bind,
-+ .unbind = vc4_dsi_unbind,
-+};
-+
-+static int vc4_dsi_dev_probe(struct platform_device *pdev)
-+{
-+ return component_add(&pdev->dev, &vc4_dsi_ops);
-+}
-+
-+static int vc4_dsi_dev_remove(struct platform_device *pdev)
-+{
-+ component_del(&pdev->dev, &vc4_dsi_ops);
-+ return 0;
-+}
-+
-+struct platform_driver vc4_dsi_driver = {
-+ .probe = vc4_dsi_dev_probe,
-+ .remove = vc4_dsi_dev_remove,
-+ .driver = {
-+ .name = "vc4_dsi",
-+ .of_match_table = vc4_dsi_dt_match,
-+ },
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0443-drm-panel-Add-support-for-the-Raspberry-Pi-7-Touchsc.patch b/target/linux/brcm2708/patches-4.4/0443-drm-panel-Add-support-for-the-Raspberry-Pi-7-Touchsc.patch
deleted file mode 100644
index bd0623e..0000000
--- a/target/linux/brcm2708/patches-4.4/0443-drm-panel-Add-support-for-the-Raspberry-Pi-7-Touchsc.patch
+++ /dev/null
@@ -1,390 +0,0 @@
-From 42c5ac14ecc2ce912ab1d95c1509db7a41bf2348 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 26 Apr 2016 13:46:13 -0700
-Subject: [PATCH] drm/panel: Add support for the Raspberry Pi 7" Touchscreen.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/panel/Kconfig | 9 +
- drivers/gpu/drm/panel/Makefile | 1 +
- .../gpu/drm/panel/panel-raspberrypi-touchscreen.c | 347 +++++++++++++++++++++
- 3 files changed, 357 insertions(+)
- create mode 100644 drivers/gpu/drm/panel/panel-raspberrypi-touchscreen.c
-
---- a/drivers/gpu/drm/panel/Kconfig
-+++ b/drivers/gpu/drm/panel/Kconfig
-@@ -31,6 +31,15 @@ config DRM_PANEL_LG_LG4573
- Say Y here if you want to enable support for LG4573 RGB panel.
- To compile this driver as a module, choose M here.
-
-+config DRM_PANEL_RASPBERRYPI_TOUCHSCREEN
-+ tristate "Raspberry Pi 7-inch touchscreen panel"
-+ depends on DRM_MIPI_DSI
-+ depends on BACKLIGHT_CLASS_DEVICE
-+ help
-+ Say Y here if you want to enable support for the Raspberry
-+ Pi 7" Touchscreen. To compile this driver as a module,
-+ choose M here.
-+
- config DRM_PANEL_SAMSUNG_S6E8AA0
- tristate "Samsung S6E8AA0 DSI video mode panel"
- depends on OF
---- a/drivers/gpu/drm/panel/Makefile
-+++ b/drivers/gpu/drm/panel/Makefile
-@@ -1,5 +1,6 @@
- obj-$(CONFIG_DRM_PANEL_SIMPLE) += panel-simple.o
- obj-$(CONFIG_DRM_PANEL_LG_LG4573) += panel-lg-lg4573.o
-+obj-$(CONFIG_DRM_PANEL_RASPBERRYPI_TOUCHSCREEN) += panel-raspberrypi-touchscreen.o
- obj-$(CONFIG_DRM_PANEL_SAMSUNG_LD9040) += panel-samsung-ld9040.o
- obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E8AA0) += panel-samsung-s6e8aa0.o
- obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o
---- /dev/null
-+++ b/drivers/gpu/drm/panel/panel-raspberrypi-touchscreen.c
-@@ -0,0 +1,347 @@
-+/*
-+ * Copyright © 2016 Broadcom Limited
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ *
-+ * Portions of this file (derived from panel-simple.c) are:
-+ *
-+ * Copyright (C) 2013, NVIDIA Corporation. All rights reserved.
-+ *
-+ * Permission is hereby granted, free of charge, to any person obtaining a
-+ * copy of this software and associated documentation files (the "Software"),
-+ * to deal in the Software without restriction, including without limitation
-+ * the rights to use, copy, modify, merge, publish, distribute, sub license,
-+ * and/or sell copies of the Software, and to permit persons to whom the
-+ * Software is furnished to do so, subject to the following conditions:
-+ *
-+ * The above copyright notice and this permission notice (including the
-+ * next paragraph) shall be included in all copies or substantial portions
-+ * of the Software.
-+ *
-+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
-+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
-+ * FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT SHALL
-+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
-+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
-+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
-+ * DEALINGS IN THE SOFTWARE.
-+ */
-+
-+/**
-+ * DOC: Raspberry Pi 7" touchscreen panel driver.
-+ *
-+ * The 7" touchscreen consists of a DPI LCD panel, a Toshiba
-+ * TC358762XBG DSI-DPI bridge, and an I2C-connected Atmel ATTINY88-MUR
-+ * controlling power management, the LCD PWM, and the touchscreen.
-+ *
-+ * This driver presents this device as a MIPI DSI panel to the DRM
-+ * driver, and should expose the touchscreen as a HID device.
-+ */
-+
-+#include <linux/backlight.h>
-+#include <linux/delay.h>
-+#include <linux/err.h>
-+#include <linux/fb.h>
-+#include <linux/gpio.h>
-+#include <linux/gpio/consumer.h>
-+#include <linux/i2c.h>
-+#include <linux/module.h>
-+#include <linux/of.h>
-+#include <linux/of_device.h>
-+#include <linux/of_graph.h>
-+#include <linux/pm.h>
-+
-+#include <drm/drm_panel.h>
-+#include <drm/drmP.h>
-+#include <drm/drm_crtc.h>
-+#include <drm/drm_mipi_dsi.h>
-+#include <drm/drm_panel.h>
-+
-+struct rpi_touchscreen {
-+ struct drm_panel base;
-+ struct mipi_dsi_device *dsi;
-+ struct i2c_client *bridge_i2c;
-+ struct backlight_device *backlight;
-+
-+ bool prepared;
-+ bool enabled;
-+
-+ /* Version of the firmware on the bridge chip */
-+ int atmel_ver;
-+};
-+
-+static const struct drm_display_mode rpi_touchscreen_modes[] = {
-+ {
-+ /* This is assuming that we'll be running the DSI PLL
-+ * at 2Ghz / 3 (since we only get integer dividers),
-+ * so a pixel clock of 2Ghz / 3 / 8.
-+ */
-+ .clock = 83333,
-+ .hdisplay = 800,
-+ .hsync_start = 800 + 61,
-+ .hsync_end = 800 + 61 + 2,
-+ .htotal = 800 + 61 + 2 + 44,
-+ .vdisplay = 480,
-+ .vsync_start = 480 + 7,
-+ .vsync_end = 480 + 7 + 2,
-+ .vtotal = 480 + 7 + 2 + 21,
-+ .vrefresh = 60,
-+ },
-+};
-+
-+static struct rpi_touchscreen *panel_to_ts(struct drm_panel *panel)
-+{
-+ return container_of(panel, struct rpi_touchscreen, base);
-+}
-+
-+struct regdump {
-+ const char *reg;
-+ u32 offset;
-+};
-+
-+#define REGDUMP(reg) { #reg, reg }
-+
-+static int rpi_touchscreen_disable(struct drm_panel *panel)
-+{
-+ struct rpi_touchscreen *ts = panel_to_ts(panel);
-+ pr_err("disable\n");
-+
-+ if (!ts->enabled)
-+ return 0;
-+
-+ if (ts->backlight) {
-+ ts->backlight->props.power = FB_BLANK_POWERDOWN;
-+ backlight_update_status(ts->backlight);
-+ }
-+
-+ ts->enabled = false;
-+
-+ return 0;
-+}
-+
-+static int rpi_touchscreen_unprepare(struct drm_panel *panel)
-+{
-+ struct rpi_touchscreen *ts = panel_to_ts(panel);
-+
-+ if (!ts->prepared)
-+ return 0;
-+
-+ ts->prepared = false;
-+
-+ return 0;
-+}
-+
-+static int rpi_touchscreen_prepare(struct drm_panel *panel)
-+{
-+ struct rpi_touchscreen *ts = panel_to_ts(panel);
-+
-+ if (ts->prepared)
-+ return 0;
-+
-+ ts->prepared = true;
-+
-+ return 0;
-+}
-+
-+/*
-+ * Powers on the panel once the DSI link is up.
-+ *
-+ * The TC358762 is run in PLLOFF mode, where it usees the MIPI DSI
-+ * byte clock instead of an external reference clock. This means that
-+ * we need the DSI host to be on and transmitting before we start
-+ * talking to it.
-+ */
-+static int rpi_touchscreen_enable(struct drm_panel *panel)
-+{
-+ struct rpi_touchscreen *ts = panel_to_ts(panel);
-+
-+ if (ts->enabled)
-+ return 0;
-+
-+ if (ts->backlight) {
-+ ts->backlight->props.power = FB_BLANK_UNBLANK;
-+ backlight_update_status(ts->backlight);
-+ }
-+
-+ ts->enabled = true;
-+
-+ return 0;
-+}
-+
-+static int rpi_touchscreen_get_modes(struct drm_panel *panel)
-+{
-+ struct drm_connector *connector = panel->connector;
-+ struct drm_device *drm = panel->drm;
-+ unsigned int i, num = 0;
-+
-+ for (i = 0; i < ARRAY_SIZE(rpi_touchscreen_modes); i++) {
-+ const struct drm_display_mode *m = &rpi_touchscreen_modes[i];
-+ struct drm_display_mode *mode;
-+
-+ mode = drm_mode_duplicate(drm, m);
-+ if (!mode) {
-+ dev_err(drm->dev, "failed to add mode %ux%u@%u\n",
-+ m->hdisplay, m->vdisplay, m->vrefresh);
-+ continue;
-+ }
-+
-+ mode->type |= DRM_MODE_TYPE_DRIVER;
-+
-+ if (i == 0)
-+ mode->type |= DRM_MODE_TYPE_PREFERRED;
-+
-+ drm_mode_set_name(mode);
-+
-+ drm_mode_probed_add(connector, mode);
-+ num++;
-+ }
-+
-+ connector->display_info.bpc = 8;
-+ connector->display_info.width_mm = 217; /* XXX */
-+ connector->display_info.height_mm = 136; /* XXX */
-+
-+ return num;
-+}
-+
-+static int rpi_touchscreen_backlight_update(struct backlight_device *bl)
-+{
-+ int brightness = bl->props.brightness;
-+
-+ if (bl->props.power != FB_BLANK_UNBLANK ||
-+ bl->props.state & (BL_CORE_SUSPENDED | BL_CORE_FBBLANK))
-+ brightness = 0;
-+
-+ return 0;
-+}
-+
-+static const struct backlight_ops rpi_touchscreen_backlight_ops = {
-+ .update_status = rpi_touchscreen_backlight_update,
-+};
-+
-+static const struct drm_panel_funcs rpi_touchscreen_funcs = {
-+ .disable = rpi_touchscreen_disable,
-+ .unprepare = rpi_touchscreen_unprepare,
-+ .prepare = rpi_touchscreen_prepare,
-+ .enable = rpi_touchscreen_enable,
-+ .get_modes = rpi_touchscreen_get_modes,
-+};
-+
-+static struct i2c_client *rpi_touchscreen_get_i2c(struct device *dev,
-+ const char *name)
-+{
-+ struct device_node *node;
-+ struct i2c_client *client;
-+
-+ node = of_parse_phandle(dev->of_node, name, 0);
-+ if (!node)
-+ return ERR_PTR(-ENODEV);
-+
-+ client = of_find_i2c_device_by_node(node);
-+
-+ of_node_put(node);
-+
-+ return client;
-+}
-+
-+static int rpi_touchscreen_dsi_probe(struct mipi_dsi_device *dsi)
-+{
-+ struct device *dev = &dsi->dev;
-+ struct rpi_touchscreen *ts;
-+ int ret;
-+
-+ ts = devm_kzalloc(dev, sizeof(*ts), GFP_KERNEL);
-+ if (!ts)
-+ return -ENOMEM;
-+
-+ dev_set_drvdata(dev, ts);
-+
-+ ts->dsi = dsi;
-+ dsi->mode_flags = (MIPI_DSI_MODE_VIDEO |
-+ MIPI_DSI_MODE_VIDEO_SYNC_PULSE);
-+ dsi->format = MIPI_DSI_FMT_RGB888;
-+ dsi->lanes = 1;
-+
-+ ts->bridge_i2c =
-+ rpi_touchscreen_get_i2c(dev, "raspberrypi,touchscreen-bridge");
-+ if (!ts->bridge_i2c) {
-+ ret = -EPROBE_DEFER;
-+ return ret;
-+ }
-+
-+#if 0
-+ ts->backlight =
-+ devm_backlight_device_register(dev,
-+ "raspberrypi-touchscreen-backlight",
-+ dev, ts,
-+ &rpi_touchscreen_backlight_ops,
-+ NULL);
-+ if (IS_ERR(ts->backlight)) {
-+ DRM_ERROR("failed to register backlight\n");
-+ return PTR_ERR(ts->backlight);
-+ }
-+ ts->backlight->props.max_brightness = RPI_TOUCHSCREEN_MAX_BRIGHTNESS;
-+ ts->backlight->props.brightness = RPI_TOUCHSCREEN_MAX_BRIGHTNESS;
-+#endif
-+
-+ drm_panel_init(&ts->base);
-+ ts->base.dev = dev;
-+ ts->base.funcs = &rpi_touchscreen_funcs;
-+
-+ ret = drm_panel_add(&ts->base);
-+ if (ret < 0)
-+ goto err_release_bridge;
-+
-+ return mipi_dsi_attach(dsi);
-+
-+err_release_bridge:
-+ put_device(&ts->bridge_i2c->dev);
-+ return ret;
-+}
-+
-+static int rpi_touchscreen_dsi_remove(struct mipi_dsi_device *dsi)
-+{
-+ struct device *dev = &dsi->dev;
-+ struct rpi_touchscreen *ts = dev_get_drvdata(dev);
-+ int ret;
-+
-+ ret = mipi_dsi_detach(dsi);
-+ if (ret < 0) {
-+ dev_err(&dsi->dev, "failed to detach from DSI host: %d\n", ret);
-+ return ret;
-+ }
-+
-+ drm_panel_detach(&ts->base);
-+ drm_panel_remove(&ts->base);
-+
-+ put_device(&ts->bridge_i2c->dev);
-+
-+ return 0;
-+}
-+
-+static void rpi_touchscreen_dsi_shutdown(struct mipi_dsi_device *dsi)
-+{
-+ /* XXX: poweroff */
-+}
-+
-+static const struct of_device_id rpi_touchscreen_of_match[] = {
-+ { .compatible = "raspberrypi,touchscreen" },
-+ { } /* sentinel */
-+};
-+MODULE_DEVICE_TABLE(of, rpi_touchscreen_of_match);
-+
-+static struct mipi_dsi_driver rpi_touchscreen_driver = {
-+ .driver = {
-+ .name = "raspberrypi-touchscreen",
-+ .of_match_table = rpi_touchscreen_of_match,
-+ },
-+ .probe = rpi_touchscreen_dsi_probe,
-+ .remove = rpi_touchscreen_dsi_remove,
-+ .shutdown = rpi_touchscreen_dsi_shutdown,
-+};
-+module_mipi_dsi_driver(rpi_touchscreen_driver);
-+
-+MODULE_AUTHOR("Eric Anholt <eric at anholt.net>");
-+MODULE_DESCRIPTION("Raspberry Pi 7-inch touchscreen driver");
-+MODULE_LICENSE("GPL v2");
diff --git a/target/linux/brcm2708/patches-4.4/0444-BCM270X-Add-the-DSI-panel-to-the-defconfig.patch b/target/linux/brcm2708/patches-4.4/0444-BCM270X-Add-the-DSI-panel-to-the-defconfig.patch
deleted file mode 100644
index bc37487..0000000
--- a/target/linux/brcm2708/patches-4.4/0444-BCM270X-Add-the-DSI-panel-to-the-defconfig.patch
+++ /dev/null
@@ -1,31 +0,0 @@
-From ef50da8920b3b6a669b73b60100b9cfab9840547 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Thu, 2 Jun 2016 12:29:45 -0700
-Subject: [PATCH] BCM270X: Add the DSI panel to the defconfig.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 2 files changed, 2 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -822,6 +822,7 @@ CONFIG_DRM=m
- CONFIG_DRM_LOAD_EDID_FIRMWARE=y
- CONFIG_DRM_UDL=m
- CONFIG_DRM_PANEL_SIMPLE=m
-+CONFIG_DRM_PANEL_RASPBERRYPI_TOUCHSCREEN=m
- CONFIG_DRM_VC4=m
- CONFIG_FB=y
- CONFIG_FB_BCM2708=y
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -814,6 +814,7 @@ CONFIG_DRM=m
- CONFIG_DRM_LOAD_EDID_FIRMWARE=y
- CONFIG_DRM_UDL=m
- CONFIG_DRM_PANEL_SIMPLE=m
-+CONFIG_DRM_PANEL_RASPBERRYPI_TOUCHSCREEN=m
- CONFIG_DRM_VC4=m
- CONFIG_FB=y
- CONFIG_FB_BCM2708=y
diff --git a/target/linux/brcm2708/patches-4.4/0445-BCM270X-Add-the-DSI-and-DSI-panel-nodes-to-the-VC4-o.patch b/target/linux/brcm2708/patches-4.4/0445-BCM270X-Add-the-DSI-and-DSI-panel-nodes-to-the-VC4-o.patch
deleted file mode 100644
index 384ef59..0000000
--- a/target/linux/brcm2708/patches-4.4/0445-BCM270X-Add-the-DSI-and-DSI-panel-nodes-to-the-VC4-o.patch
+++ /dev/null
@@ -1,84 +0,0 @@
-From 2a089ea1c91d13333302ca181643ead14fbc461b Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Thu, 2 Jun 2016 15:09:35 -0700
-Subject: [PATCH] BCM270X: Add the DSI and DSI panel nodes to the VC4 overlay.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- arch/arm/boot/dts/bcm2708_common.dtsi | 24 ++++++++++++++++++++--
- arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts | 16 +++++++++++++++
- 2 files changed, 38 insertions(+), 2 deletions(-)
-
---- a/arch/arm/boot/dts/bcm2708_common.dtsi
-+++ b/arch/arm/boot/dts/bcm2708_common.dtsi
-@@ -2,6 +2,7 @@
- #include <dt-bindings/clock/bcm2835-aux.h>
- #include "dt-bindings/power/raspberrypi-power.h"
- #include "dt-bindings/gpio/gpio.h"
-+#include "dt-bindings/pinctrl/bcm2835.h"
- #include "skeleton.dtsi"
-
- / {
-@@ -110,9 +111,10 @@
- reg = <0x7e101000 0x2000>;
-
- /* CPRMAN derives everything from the platform's
-- * oscillator.
-+ * oscillator except for a few clocks that may
-+ * derive from something else derived from CPRMAN..
- */
-- clocks = <&clk_osc>;
-+ clocks = <&clk_osc>, <&dsi1 0>, <&dsi1 1>, <&dsi1 2>;
- status = "disabled";
- };
-
-@@ -282,6 +284,24 @@
- status = "disabled";
- };
-
-+ dsi1: dsi at 7e700000 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ #clock-cells = <1>;
-+
-+ compatible = "brcm,bcm2835-dsi1";
-+ reg = <0x7e700000 0x8c>;
-+ interrupts = <2 12>;
-+
-+ clocks = <&cprman BCM2835_PLLD_DSI1>,
-+ <&cprman BCM2835_CLOCK_DSI1E>,
-+ <&cprman BCM2835_CLOCK_DSI1P>;
-+ clock-names = "phy", "escape", "pixel";
-+ clock-output-names = "dsi1_byte", "dsi1_ddr2", "dsi1_ddr";
-+ status = "disabled";
-+ power-domains = <&power RPI_POWER_DOMAIN_DSI1>;
-+ };
-+
- i2c1: i2c at 7e804000 {
- compatible = "brcm,bcm2708-i2c";
- reg = <0x7e804000 0x1000>;
---- a/arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts
-@@ -126,6 +126,22 @@
- };
- };
-
-+ fragment at 16 {
-+ target = <&dsi1>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ brcm,panel = <&pitouchscreen>;
-+
-+ pitouchscreen: panel {
-+ compatible = "raspberrypi,touchscreen";
-+ reg = <0>;
-+ };
-+ };
-+ };
-+
- __overrides__ {
- cma-256 = <0>,"+0-1-2-3-4";
- cma-192 = <0>,"-0+1-2-3-4";
diff --git a/target/linux/brcm2708/patches-4.4/0446-of-Export-of_device_uevent_modalias-for-DRM_MIPI_DSI.patch b/target/linux/brcm2708/patches-4.4/0446-of-Export-of_device_uevent_modalias-for-DRM_MIPI_DSI.patch
deleted file mode 100644
index 15f65f1..0000000
--- a/target/linux/brcm2708/patches-4.4/0446-of-Export-of_device_uevent_modalias-for-DRM_MIPI_DSI.patch
+++ /dev/null
@@ -1,21 +0,0 @@
-From 0456e24bfc7e0dc2fa3145fa199c2a2a097953c0 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 9 Aug 2016 15:12:06 -0700
-Subject: [PATCH] of: Export of_device_uevent_modalias for DRM_MIPI_DSI.
-
-In order to make DSI panel modules able to load automatically, we need
-to emit the OF modalias uevent so that their MODULE_DEVICE_TABLE(of,
-...) can match against it.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/of/device.c | 1 +
- 1 file changed, 1 insertion(+)
-
---- a/drivers/of/device.c
-+++ b/drivers/of/device.c
-@@ -287,3 +287,4 @@ int of_device_uevent_modalias(struct dev
-
- return 0;
- }
-+EXPORT_SYMBOL(of_device_uevent_modalias);
diff --git a/target/linux/brcm2708/patches-4.4/0447-drm-Emit-modalias-uevents-for-the-DSI-devices-we-cre.patch b/target/linux/brcm2708/patches-4.4/0447-drm-Emit-modalias-uevents-for-the-DSI-devices-we-cre.patch
deleted file mode 100644
index 07bb779..0000000
--- a/target/linux/brcm2708/patches-4.4/0447-drm-Emit-modalias-uevents-for-the-DSI-devices-we-cre.patch
+++ /dev/null
@@ -1,48 +0,0 @@
-From 4f0506089cef66d8138da5f611e621a24b9d7296 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 9 Aug 2016 15:13:33 -0700
-Subject: [PATCH] drm: Emit modalias uevents for the DSI devices we create.
-
-This gets the Raspberry Pi panel module to automatically load at boot
-time.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/drm_mipi_dsi.c | 19 +++++++++++++++++++
- 1 file changed, 19 insertions(+)
-
---- a/drivers/gpu/drm/drm_mipi_dsi.c
-+++ b/drivers/gpu/drm/drm_mipi_dsi.c
-@@ -50,6 +50,24 @@ static int mipi_dsi_device_match(struct
- return of_driver_match_device(dev, drv);
- }
-
-+/**
-+ * Send modalias events when devices are created on the bus, so that
-+ * modules can load automatically.
-+ */
-+static int mipi_dsi_uevent(struct device *dev, struct kobj_uevent_env *env)
-+{
-+ int rc;
-+
-+ /* Just do the OF uevent, which emits the compatible string so
-+ * that a MODULE_DEVICE_TABLE(of, ...) works.
-+ */
-+ rc = of_device_uevent_modalias(dev, env);
-+ if (rc != -ENODEV)
-+ return rc;
-+
-+ return 0;
-+}
-+
- static const struct dev_pm_ops mipi_dsi_device_pm_ops = {
- .runtime_suspend = pm_generic_runtime_suspend,
- .runtime_resume = pm_generic_runtime_resume,
-@@ -65,6 +83,7 @@ static struct bus_type mipi_dsi_bus_type
- .name = "mipi-dsi",
- .match = mipi_dsi_device_match,
- .pm = &mipi_dsi_device_pm_ops,
-+ .uevent = mipi_dsi_uevent,
- };
-
- static int of_device_match(struct device *dev, void *data)
diff --git a/target/linux/brcm2708/patches-4.4/0448-gpu-drm-vc4_hdmi-add-missing-of_node_put-after-calli.patch b/target/linux/brcm2708/patches-4.4/0448-gpu-drm-vc4_hdmi-add-missing-of_node_put-after-calli.patch
deleted file mode 100644
index 2c682a0..0000000
--- a/target/linux/brcm2708/patches-4.4/0448-gpu-drm-vc4_hdmi-add-missing-of_node_put-after-calli.patch
+++ /dev/null
@@ -1,46 +0,0 @@
-From e190604e4821a0b9cceebb53b21d890a84cdccbf Mon Sep 17 00:00:00 2001
-From: Peter Chen <peter.chen at nxp.com>
-Date: Tue, 5 Jul 2016 10:04:54 +0800
-Subject: [PATCH] gpu: drm: vc4_hdmi: add missing of_node_put after calling
- of_parse_phandle
-
-of_node_put needs to be called when the device node which is got
-from of_parse_phandle has finished using.
-
-Signed-off-by: Peter Chen <peter.chen at nxp.com>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 027a697677b0d5ff211773596d96f84078ceda80)
----
- drivers/gpu/drm/vc4/vc4_hdmi.c | 13 +++++++------
- 1 file changed, 7 insertions(+), 6 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_hdmi.c
-+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
-@@ -467,12 +467,6 @@ static int vc4_hdmi_bind(struct device *
- if (IS_ERR(hdmi->hd_regs))
- return PTR_ERR(hdmi->hd_regs);
-
-- ddc_node = of_parse_phandle(dev->of_node, "ddc", 0);
-- if (!ddc_node) {
-- DRM_ERROR("Failed to find ddc node in device tree\n");
-- return -ENODEV;
-- }
--
- hdmi->pixel_clock = devm_clk_get(dev, "pixel");
- if (IS_ERR(hdmi->pixel_clock)) {
- DRM_ERROR("Failed to get pixel clock\n");
-@@ -484,7 +478,14 @@ static int vc4_hdmi_bind(struct device *
- return PTR_ERR(hdmi->hsm_clock);
- }
-
-+ ddc_node = of_parse_phandle(dev->of_node, "ddc", 0);
-+ if (!ddc_node) {
-+ DRM_ERROR("Failed to find ddc node in device tree\n");
-+ return -ENODEV;
-+ }
-+
- hdmi->ddc = of_find_i2c_adapter_by_node(ddc_node);
-+ of_node_put(ddc_node);
- if (!hdmi->ddc) {
- DRM_DEBUG("Failed to get ddc i2c adapter by node\n");
- return -EPROBE_DEFER;
diff --git a/target/linux/brcm2708/patches-4.4/0449-drm-vc4-Use-for_each_plane_in_state.patch b/target/linux/brcm2708/patches-4.4/0449-drm-vc4-Use-for_each_plane_in_state.patch
deleted file mode 100644
index 2582c33..0000000
--- a/target/linux/brcm2708/patches-4.4/0449-drm-vc4-Use-for_each_plane_in_state.patch
+++ /dev/null
@@ -1,42 +0,0 @@
-From 9c89a2669e825428103518288426dcc3936112f1 Mon Sep 17 00:00:00 2001
-From: Daniel Vetter <daniel.vetter at ffwll.ch>
-Date: Thu, 2 Jun 2016 00:06:28 +0200
-Subject: [PATCH] drm/vc4: Use for_each_plane_in_state
-
-We want to hide drm_atomic_stat internals a bit better.
-
-Cc: Eric Anholt <eric at anholt.net>
-Reviewed-by: Maarten Lankhorst <maarten.lankhorst at linux.intel.com>
-Signed-off-by: Daniel Vetter <daniel.vetter at intel.com>
-Link: http://patchwork.freedesktop.org/patch/msgid/1464818821-5736-6-git-send-email-daniel.vetter@ffwll.ch
-(cherry picked from commit 833cd78adbc236db684f19e93121d4bf6659a8af)
----
- drivers/gpu/drm/vc4/vc4_kms.c | 10 +++-------
- 1 file changed, 3 insertions(+), 7 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_kms.c
-+++ b/drivers/gpu/drm/vc4/vc4_kms.c
-@@ -111,6 +111,8 @@ static int vc4_atomic_commit(struct drm_
- int i;
- uint64_t wait_seqno = 0;
- struct vc4_commit *c;
-+ struct drm_plane *plane;
-+ struct drm_plane_state *new_state;
-
- c = commit_init(state);
- if (!c)
-@@ -130,13 +132,7 @@ static int vc4_atomic_commit(struct drm_
- return ret;
- }
-
-- for (i = 0; i < dev->mode_config.num_total_plane; i++) {
-- struct drm_plane *plane = state->planes[i];
-- struct drm_plane_state *new_state = state->plane_states[i];
--
-- if (!plane)
-- continue;
--
-+ for_each_plane_in_state(state, plane, new_state, i) {
- if ((plane->state->fb != new_state->fb) && new_state->fb) {
- struct drm_gem_cma_object *cma_bo =
- drm_fb_cma_get_gem_obj(new_state->fb, 0);
diff --git a/target/linux/brcm2708/patches-4.4/0450-drm-vc4-Fix-ioctl-permissions-for-render-nodes.patch b/target/linux/brcm2708/patches-4.4/0450-drm-vc4-Fix-ioctl-permissions-for-render-nodes.patch
deleted file mode 100644
index ffc593a..0000000
--- a/target/linux/brcm2708/patches-4.4/0450-drm-vc4-Fix-ioctl-permissions-for-render-nodes.patch
+++ /dev/null
@@ -1,39 +0,0 @@
-From 78480484281e0a867f7de1db9f9e0f13810a29d7 Mon Sep 17 00:00:00 2001
-From: Herve Jourdain <herve.jourdain at neuf.fr>
-Date: Wed, 1 Jun 2016 02:24:46 +0800
-Subject: [PATCH] drm/vc4: Fix ioctl permissions for render nodes.
-
-Contrary to other flags to DRM_IOCTL_DEF_DRV(), which restrict usage,
-the flag for render node is an enabler (the IOCTL can't be used from
-render node if it's not present). So DRM_RENDER_ALLOW needs to be
-added to all the flags that were previously 0.
-
-Signed-off-by: Herve Jourdain <herve.jourdain at neuf.fr>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-Fixes: 0cd3e2747662 ("drm/vc4: Add missing render node support")
-(cherry picked from commit b10c22e5f9902a329450c2027e9291b71e9f1602)
----
- drivers/gpu/drm/vc4/vc4_drv.c | 12 ++++++------
- 1 file changed, 6 insertions(+), 6 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_drv.c
-+++ b/drivers/gpu/drm/vc4/vc4_drv.c
-@@ -88,12 +88,12 @@ static const struct file_operations vc4_
- };
-
- static const struct drm_ioctl_desc vc4_drm_ioctls[] = {
-- DRM_IOCTL_DEF_DRV(VC4_SUBMIT_CL, vc4_submit_cl_ioctl, 0),
-- DRM_IOCTL_DEF_DRV(VC4_WAIT_SEQNO, vc4_wait_seqno_ioctl, 0),
-- DRM_IOCTL_DEF_DRV(VC4_WAIT_BO, vc4_wait_bo_ioctl, 0),
-- DRM_IOCTL_DEF_DRV(VC4_CREATE_BO, vc4_create_bo_ioctl, 0),
-- DRM_IOCTL_DEF_DRV(VC4_MMAP_BO, vc4_mmap_bo_ioctl, 0),
-- DRM_IOCTL_DEF_DRV(VC4_CREATE_SHADER_BO, vc4_create_shader_bo_ioctl, 0),
-+ DRM_IOCTL_DEF_DRV(VC4_SUBMIT_CL, vc4_submit_cl_ioctl, DRM_RENDER_ALLOW),
-+ DRM_IOCTL_DEF_DRV(VC4_WAIT_SEQNO, vc4_wait_seqno_ioctl, DRM_RENDER_ALLOW),
-+ DRM_IOCTL_DEF_DRV(VC4_WAIT_BO, vc4_wait_bo_ioctl, DRM_RENDER_ALLOW),
-+ DRM_IOCTL_DEF_DRV(VC4_CREATE_BO, vc4_create_bo_ioctl, DRM_RENDER_ALLOW),
-+ DRM_IOCTL_DEF_DRV(VC4_MMAP_BO, vc4_mmap_bo_ioctl, DRM_RENDER_ALLOW),
-+ DRM_IOCTL_DEF_DRV(VC4_CREATE_SHADER_BO, vc4_create_shader_bo_ioctl, DRM_RENDER_ALLOW),
- DRM_IOCTL_DEF_DRV(VC4_GET_HANG_STATE, vc4_get_hang_state_ioctl,
- DRM_ROOT_ONLY),
- };
diff --git a/target/linux/brcm2708/patches-4.4/0451-drm-vc4-Make-pageflip-completion-handling-more-robus.patch b/target/linux/brcm2708/patches-4.4/0451-drm-vc4-Make-pageflip-completion-handling-more-robus.patch
deleted file mode 100644
index 88b8c03..0000000
--- a/target/linux/brcm2708/patches-4.4/0451-drm-vc4-Make-pageflip-completion-handling-more-robus.patch
+++ /dev/null
@@ -1,126 +0,0 @@
-From 8a7bf555e2fa4a6f683a06e3b474cf4751181557 Mon Sep 17 00:00:00 2001
-From: Mario Kleiner <mario.kleiner.de at gmail.com>
-Date: Wed, 18 May 2016 14:02:46 +0200
-Subject: [PATCH] drm/vc4: Make pageflip completion handling more robust.
-
-Protect both the setup of the pageflip event and the
-latching of the new requested displaylist head pointer
-by the event lock, so we can't get into a situation
-where vc4_atomic_flush latches the new display list via
-HVS_WRITE, then immediately gets preempted before queueing
-the pageflip event, then the page-flip completes in hw and
-the vc4_crtc_handle_page_flip() runs and no-ops due to
-lack of a pending pageflip event, then vc4_atomic_flush
-continues and only then queues the pageflip event - after
-the page flip handling already no-oped. This would cause
-flip completion handling only at the next vblank - one
-frame too late.
-
-In vc4_crtc_handle_page_flip() check the actual DL head
-pointer in SCALER_DISPLACTX against the requested pointer
-for page flip to make sure that the flip actually really
-completed in the current vblank and doesn't get deferred
-to the next one because the DL head pointer was written
-a bit too late into SCALER_DISPLISTX, after start of
-vblank, and missed the boat. This avoids handling a
-pageflip completion too early - one frame too early.
-
-According to Eric, DL head pointer updates which were
-written into the HVS DISPLISTX reg get committed to hardware
-at the last pixel of active scanout. Our vblank interrupt
-handler, as triggered by PV_INT_VFP_START irq, gets to run
-earliest at the first pixel of HBLANK at the end of the
-last scanline of active scanout, ie. vblank irq handling
-runs at least 1 pixel duration after a potential pageflip
-completion happened in hardware.
-
-This ordering of events in the hardware, together with the
-lock protection and SCALER_DISPLACTX sampling of this patch,
-guarantees that pageflip completion handling only runs at
-exactly the vblank irq of actual pageflip completion in all
-cases.
-
-Background info from Eric about the relative timing of
-HVS, PV's and trigger points for interrupts, DL updates:
-
-https://lists.freedesktop.org/archives/dri-devel/2016-May/107510.html
-
-Tested on RPi 2B with hardware timing measurement equipment
-and shown to no longer complete flips too early or too late.
-
-Signed-off-by: Mario Kleiner <mario.kleiner.de at gmail.com>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 56d1fe0979dc9b73c1c12ee07722ac380d42a0c4)
----
- drivers/gpu/drm/vc4/vc4_crtc.c | 28 ++++++++++++++++++----------
- drivers/gpu/drm/vc4/vc4_regs.h | 4 ++++
- 2 files changed, 22 insertions(+), 10 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_crtc.c
-+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
-@@ -465,14 +465,6 @@ static void vc4_crtc_atomic_flush(struct
-
- WARN_ON_ONCE(dlist_next - dlist_start != vc4_state->mm.size);
-
-- HVS_WRITE(SCALER_DISPLISTX(vc4_crtc->channel),
-- vc4_state->mm.start);
--
-- if (debug_dump_regs) {
-- DRM_INFO("CRTC %d HVS after:\n", drm_crtc_index(crtc));
-- vc4_hvs_dump_state(dev);
-- }
--
- if (crtc->state->event) {
- unsigned long flags;
-
-@@ -482,8 +474,20 @@ static void vc4_crtc_atomic_flush(struct
-
- spin_lock_irqsave(&dev->event_lock, flags);
- vc4_crtc->event = crtc->state->event;
-- spin_unlock_irqrestore(&dev->event_lock, flags);
- crtc->state->event = NULL;
-+
-+ HVS_WRITE(SCALER_DISPLISTX(vc4_crtc->channel),
-+ vc4_state->mm.start);
-+
-+ spin_unlock_irqrestore(&dev->event_lock, flags);
-+ } else {
-+ HVS_WRITE(SCALER_DISPLISTX(vc4_crtc->channel),
-+ vc4_state->mm.start);
-+ }
-+
-+ if (debug_dump_regs) {
-+ DRM_INFO("CRTC %d HVS after:\n", drm_crtc_index(crtc));
-+ vc4_hvs_dump_state(dev);
- }
- }
-
-@@ -509,10 +513,14 @@ static void vc4_crtc_handle_page_flip(st
- {
- struct drm_crtc *crtc = &vc4_crtc->base;
- struct drm_device *dev = crtc->dev;
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(crtc->state);
-+ u32 chan = vc4_crtc->channel;
- unsigned long flags;
-
- spin_lock_irqsave(&dev->event_lock, flags);
-- if (vc4_crtc->event) {
-+ if (vc4_crtc->event &&
-+ (vc4_state->mm.start == HVS_READ(SCALER_DISPLACTX(chan)))) {
- drm_crtc_send_vblank_event(crtc, vc4_crtc->event);
- vc4_crtc->event = NULL;
- drm_crtc_vblank_put(crtc);
---- a/drivers/gpu/drm/vc4/vc4_regs.h
-+++ b/drivers/gpu/drm/vc4/vc4_regs.h
-@@ -343,6 +343,10 @@
- #define SCALER_DISPLACT0 0x00000030
- #define SCALER_DISPLACT1 0x00000034
- #define SCALER_DISPLACT2 0x00000038
-+#define SCALER_DISPLACTX(x) (SCALER_DISPLACT0 + \
-+ (x) * (SCALER_DISPLACT1 - \
-+ SCALER_DISPLACT0))
-+
- #define SCALER_DISPCTRL0 0x00000040
- # define SCALER_DISPCTRLX_ENABLE BIT(31)
- # define SCALER_DISPCTRLX_RESET BIT(30)
diff --git a/target/linux/brcm2708/patches-4.4/0452-drm-vc4-clean-up-error-exit-path-on-failed-dpi_conne.patch b/target/linux/brcm2708/patches-4.4/0452-drm-vc4-clean-up-error-exit-path-on-failed-dpi_conne.patch
deleted file mode 100644
index b405d38..0000000
--- a/target/linux/brcm2708/patches-4.4/0452-drm-vc4-clean-up-error-exit-path-on-failed-dpi_conne.patch
+++ /dev/null
@@ -1,53 +0,0 @@
-From 9fad3809c56136a3c8e66fa35bba0da9c9e4f0da Mon Sep 17 00:00:00 2001
-From: Colin Ian King <colin.king at canonical.com>
-Date: Thu, 2 Jun 2016 10:38:29 +0100
-Subject: [PATCH] drm/vc4: clean up error exit path on failed dpi_connector
- allocation
-
-There is redundant code in the clean up exit path when dpi_connector
-fails to be allocated. The current code checks if connector is NULL
-before destroying it, in fact, connector is NULL at this point so
-the check is redundant and can be removed. The final clean up is
-that we can remove the goto fail with a simple return and the unused
-variable ret.
-
-Signed-off-by: Colin Ian King <colin.king at canonical.com>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit a9402dfe17bddeee5c72943385eaa13c39f106f7)
----
- drivers/gpu/drm/vc4/vc4_dpi.c | 14 +++-----------
- 1 file changed, 3 insertions(+), 11 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_dpi.c
-+++ b/drivers/gpu/drm/vc4/vc4_dpi.c
-@@ -236,14 +236,12 @@ static struct drm_connector *vc4_dpi_con
- {
- struct drm_connector *connector = NULL;
- struct vc4_dpi_connector *dpi_connector;
-- int ret = 0;
-
- dpi_connector = devm_kzalloc(dev->dev, sizeof(*dpi_connector),
- GFP_KERNEL);
-- if (!dpi_connector) {
-- ret = -ENOMEM;
-- goto fail;
-- }
-+ if (!dpi_connector)
-+ return ERR_PTR(-ENOMEM);
-+
- connector = &dpi_connector->base;
-
- dpi_connector->encoder = dpi->encoder;
-@@ -260,12 +258,6 @@ static struct drm_connector *vc4_dpi_con
- drm_mode_connector_attach_encoder(connector, dpi->encoder);
-
- return connector;
--
-- fail:
-- if (connector)
-- vc4_dpi_connector_destroy(connector);
--
-- return ERR_PTR(ret);
- }
-
- static const struct drm_encoder_funcs vc4_dpi_encoder_funcs = {
diff --git a/target/linux/brcm2708/patches-4.4/0453-drm-vc4-enable-XBGR8888-and-ABGR8888-pixel-formats.patch b/target/linux/brcm2708/patches-4.4/0453-drm-vc4-enable-XBGR8888-and-ABGR8888-pixel-formats.patch
deleted file mode 100644
index 92fe9b3..0000000
--- a/target/linux/brcm2708/patches-4.4/0453-drm-vc4-enable-XBGR8888-and-ABGR8888-pixel-formats.patch
+++ /dev/null
@@ -1,34 +0,0 @@
-From 6e069ea26c09f7193b6ea1e86ccf6cedaf5a6d31 Mon Sep 17 00:00:00 2001
-From: Rob Herring <robh at kernel.org>
-Date: Thu, 9 Jun 2016 16:19:25 -0500
-Subject: [PATCH] drm: vc4: enable XBGR8888 and ABGR8888 pixel formats
-
-DRM_FORMAT_XBGR8888 and DRM_FORMAT_ABGR8888 are 2 of the native formats
-used in Android, so enable them for VC4. There seems to be no logic behind
-HVS_PIXEL_ORDER_xxxx naming, but HVS_PIXEL_ORDER_ARGB seems to work
-correctly.
-
-Signed-off-by: Rob Herring <robh at kernel.org>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 93977767f092fbf0787e5d2a0bf2e0a3fc6f6ced)
----
- drivers/gpu/drm/vc4/vc4_plane.c | 8 ++++++++
- 1 file changed, 8 insertions(+)
-
---- a/drivers/gpu/drm/vc4/vc4_plane.c
-+++ b/drivers/gpu/drm/vc4/vc4_plane.c
-@@ -94,6 +94,14 @@ static const struct hvs_format {
- .pixel_order = HVS_PIXEL_ORDER_ABGR, .has_alpha = true,
- },
- {
-+ .drm = DRM_FORMAT_ABGR8888, .hvs = HVS_PIXEL_FORMAT_RGBA8888,
-+ .pixel_order = HVS_PIXEL_ORDER_ARGB, .has_alpha = true,
-+ },
-+ {
-+ .drm = DRM_FORMAT_XBGR8888, .hvs = HVS_PIXEL_FORMAT_RGBA8888,
-+ .pixel_order = HVS_PIXEL_ORDER_ARGB, .has_alpha = false,
-+ },
-+ {
- .drm = DRM_FORMAT_RGB565, .hvs = HVS_PIXEL_FORMAT_RGB565,
- .pixel_order = HVS_PIXEL_ORDER_XRGB, .has_alpha = false,
- },
diff --git a/target/linux/brcm2708/patches-4.4/0454-drm-vc4-Bind-the-HVS-before-we-bind-the-individual-C.patch b/target/linux/brcm2708/patches-4.4/0454-drm-vc4-Bind-the-HVS-before-we-bind-the-individual-C.patch
deleted file mode 100644
index 87c4918..0000000
--- a/target/linux/brcm2708/patches-4.4/0454-drm-vc4-Bind-the-HVS-before-we-bind-the-individual-C.patch
+++ /dev/null
@@ -1,28 +0,0 @@
-From acb39d9a371298b05bc337c99647ba2f2b335136 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 8 Jul 2016 11:25:09 -0700
-Subject: [PATCH] drm/vc4: Bind the HVS before we bind the individual CRTCs.
-
-We need to be able to look at the CRTC's registers in the HVS as part
-of initialization, while the HVS doesn't need to look at the PV
-registers.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Reviewed-and-tested-by: Mario Kleiner <mario.kleiner.de at gmail.com>
-(cherry picked from commit 7a100969f30b77761901c05a5c810bcaea65df44)
----
- drivers/gpu/drm/vc4/vc4_drv.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/gpu/drm/vc4/vc4_drv.c
-+++ b/drivers/gpu/drm/vc4/vc4_drv.c
-@@ -295,8 +295,8 @@ static struct platform_driver *const com
- &vc4_hdmi_driver,
- &vc4_dpi_driver,
- &vc4_dsi_driver,
-- &vc4_crtc_driver,
- &vc4_hvs_driver,
-+ &vc4_crtc_driver,
- &vc4_v3d_driver,
- };
-
diff --git a/target/linux/brcm2708/patches-4.4/0455-drm-vc4-Implement-precise-vblank-timestamping.patch b/target/linux/brcm2708/patches-4.4/0455-drm-vc4-Implement-precise-vblank-timestamping.patch
deleted file mode 100644
index 01e98b6..0000000
--- a/target/linux/brcm2708/patches-4.4/0455-drm-vc4-Implement-precise-vblank-timestamping.patch
+++ /dev/null
@@ -1,358 +0,0 @@
-From e00fc67625343bada3805ea13cbcd69dfb2ba242 Mon Sep 17 00:00:00 2001
-From: Mario Kleiner <mario.kleiner.de at gmail.com>
-Date: Thu, 23 Jun 2016 08:17:50 +0200
-Subject: [PATCH] drm/vc4: Implement precise vblank timestamping.
-
-Precise vblank timestamping is implemented via the
-usual scanout position based method. On VC4 the
-pixelvalves PV do not have a scanout position
-register. Only the hardware video scaler HVS has a
-similar register which describes which scanline for
-the output is currently composited and stored in the
-HVS fifo for later consumption by the PV.
-
-This causes a problem in that the HVS runs at a much
-faster clock (system clock / audio gate) than the PV
-which runs at video mode dot clock, so the unless the
-fifo between HVS and PV is full, the HVS will progress
-faster in its observable read line position than video
-scan rate, so the HVS position reading can't be directly
-translated into a scanout position for timestamp correction.
-
-Additionally when the PV is in vblank, it doesn't consume
-from the fifo, so the fifo gets full very quickly and then
-the HVS stops compositing until the PV enters active scanout
-and starts consuming scanlines from the fifo again, making
-new space for the HVS to composite.
-
-Therefore a simple translation of HVS read position into
-elapsed time since (or to) start of active scanout does
-not work, but for the most interesting cases we can still
-get useful and sufficiently accurate results:
-
-1. The PV enters active scanout of a new frame with the
- fifo of the HVS completely full, and the HVS can refill
- any fifo line which gets consumed and thereby freed up by
- the PV during active scanout very quickly. Therefore the
- PV and HVS work effectively in lock-step during active
- scanout with the fifo never having more than 1 scanline
- freed up by the PV before it gets refilled. The PV's
- real scanout position is therefore trailing the HVS
- compositing position as scanoutpos = hvspos - fifosize
- and we can get the true scanoutpos as HVS readpos minus
- fifo size, so precise timestamping works while in active
- scanout, except for the last few scanlines of the frame,
- when the HVS reaches end of frame, stops compositing and
- the PV catches up and drains the fifo. This special case
- would only introduce minor errors though.
-
-2. If we are in vblank, then we can only guess something
- reasonable. If called from vblank irq, we assume the irq is
- usually dispatched with minimum delay, so we can take a
- timestamp taken at entry into the vblank irq handler as a
- baseline and then add a full vblank duration until the
- guessed start of active scanout. As irq dispatch is usually
- pretty low latency this works with relatively low jitter and
- good results.
-
- If we aren't called from vblank then we could be anywhere
- within the vblank interval, so we return a neutral result,
- simply the current system timestamp, and hope for the best.
-
-Measurement shows the generated timestamps to be rather precise,
-and at least never off more than 1 vblank duration worst-case.
-
-Limitations: Doesn't work well yet for interlaced video modes,
- therefore disabled in interlaced mode for now.
-
-v2: Use the DISPBASE registers to determine the FIFO size (changes
- by anholt)
-
-Signed-off-by: Mario Kleiner <mario.kleiner.de at gmail.com>
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Reviewed-and-tested-by: Mario Kleiner <mario.kleiner.de at gmail.com> (v2)
-(cherry picked from commit 1bf59f1dcbe25272f6b5d870054647e58a8a9c55)
----
- drivers/gpu/drm/vc4/vc4_crtc.c | 162 +++++++++++++++++++++++++++++++++++++++++
- drivers/gpu/drm/vc4/vc4_drv.c | 2 +
- drivers/gpu/drm/vc4/vc4_drv.h | 7 ++
- drivers/gpu/drm/vc4/vc4_regs.h | 22 +++++-
- 4 files changed, 192 insertions(+), 1 deletion(-)
-
---- a/drivers/gpu/drm/vc4/vc4_crtc.c
-+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
-@@ -47,12 +47,17 @@ struct vc4_crtc {
- const struct vc4_crtc_data *data;
- void __iomem *regs;
-
-+ /* Timestamp at start of vblank irq - unaffected by lock delays. */
-+ ktime_t t_vblank;
-+
- /* Which HVS channel we're using for our CRTC. */
- int channel;
-
- u8 lut_r[256];
- u8 lut_g[256];
- u8 lut_b[256];
-+ /* Size in pixels of the COB memory allocated to this CRTC. */
-+ u32 cob_size;
-
- struct drm_pending_vblank_event *event;
- };
-@@ -134,6 +139,144 @@ int vc4_crtc_debugfs_regs(struct seq_fil
- }
- #endif
-
-+int vc4_crtc_get_scanoutpos(struct drm_device *dev, unsigned int crtc_id,
-+ unsigned int flags, int *vpos, int *hpos,
-+ ktime_t *stime, ktime_t *etime,
-+ const struct drm_display_mode *mode)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ struct vc4_crtc *vc4_crtc = vc4->crtc[crtc_id];
-+ u32 val;
-+ int fifo_lines;
-+ int vblank_lines;
-+ int ret = 0;
-+
-+ /*
-+ * XXX Doesn't work well in interlaced mode yet, partially due
-+ * to problems in vc4 kms or drm core interlaced mode handling,
-+ * so disable for now in interlaced mode.
-+ */
-+ if (mode->flags & DRM_MODE_FLAG_INTERLACE)
-+ return ret;
-+
-+ /* preempt_disable_rt() should go right here in PREEMPT_RT patchset. */
-+
-+ /* Get optional system timestamp before query. */
-+ if (stime)
-+ *stime = ktime_get();
-+
-+ /*
-+ * Read vertical scanline which is currently composed for our
-+ * pixelvalve by the HVS, and also the scaler status.
-+ */
-+ val = HVS_READ(SCALER_DISPSTATX(vc4_crtc->channel));
-+
-+ /* Get optional system timestamp after query. */
-+ if (etime)
-+ *etime = ktime_get();
-+
-+ /* preempt_enable_rt() should go right here in PREEMPT_RT patchset. */
-+
-+ /* Vertical position of hvs composed scanline. */
-+ *vpos = VC4_GET_FIELD(val, SCALER_DISPSTATX_LINE);
-+
-+ /* No hpos info available. */
-+ if (hpos)
-+ *hpos = 0;
-+
-+ /* This is the offset we need for translating hvs -> pv scanout pos. */
-+ fifo_lines = vc4_crtc->cob_size / mode->crtc_hdisplay;
-+
-+ if (fifo_lines > 0)
-+ ret |= DRM_SCANOUTPOS_VALID;
-+
-+ /* HVS more than fifo_lines into frame for compositing? */
-+ if (*vpos > fifo_lines) {
-+ /*
-+ * We are in active scanout and can get some meaningful results
-+ * from HVS. The actual PV scanout can not trail behind more
-+ * than fifo_lines as that is the fifo's capacity. Assume that
-+ * in active scanout the HVS and PV work in lockstep wrt. HVS
-+ * refilling the fifo and PV consuming from the fifo, ie.
-+ * whenever the PV consumes and frees up a scanline in the
-+ * fifo, the HVS will immediately refill it, therefore
-+ * incrementing vpos. Therefore we choose HVS read position -
-+ * fifo size in scanlines as a estimate of the real scanout
-+ * position of the PV.
-+ */
-+ *vpos -= fifo_lines + 1;
-+ if (mode->flags & DRM_MODE_FLAG_INTERLACE)
-+ *vpos /= 2;
-+
-+ ret |= DRM_SCANOUTPOS_ACCURATE;
-+ return ret;
-+ }
-+
-+ /*
-+ * Less: This happens when we are in vblank and the HVS, after getting
-+ * the VSTART restart signal from the PV, just started refilling its
-+ * fifo with new lines from the top-most lines of the new framebuffers.
-+ * The PV does not scan out in vblank, so does not remove lines from
-+ * the fifo, so the fifo will be full quickly and the HVS has to pause.
-+ * We can't get meaningful readings wrt. scanline position of the PV
-+ * and need to make things up in a approximative but consistent way.
-+ */
-+ ret |= DRM_SCANOUTPOS_IN_VBLANK;
-+ vblank_lines = mode->crtc_vtotal - mode->crtc_vdisplay;
-+
-+ if (flags & DRM_CALLED_FROM_VBLIRQ) {
-+ /*
-+ * Assume the irq handler got called close to first
-+ * line of vblank, so PV has about a full vblank
-+ * scanlines to go, and as a base timestamp use the
-+ * one taken at entry into vblank irq handler, so it
-+ * is not affected by random delays due to lock
-+ * contention on event_lock or vblank_time lock in
-+ * the core.
-+ */
-+ *vpos = -vblank_lines;
-+
-+ if (stime)
-+ *stime = vc4_crtc->t_vblank;
-+ if (etime)
-+ *etime = vc4_crtc->t_vblank;
-+
-+ /*
-+ * If the HVS fifo is not yet full then we know for certain
-+ * we are at the very beginning of vblank, as the hvs just
-+ * started refilling, and the stime and etime timestamps
-+ * truly correspond to start of vblank.
-+ */
-+ if ((val & SCALER_DISPSTATX_FULL) != SCALER_DISPSTATX_FULL)
-+ ret |= DRM_SCANOUTPOS_ACCURATE;
-+ } else {
-+ /*
-+ * No clue where we are inside vblank. Return a vpos of zero,
-+ * which will cause calling code to just return the etime
-+ * timestamp uncorrected. At least this is no worse than the
-+ * standard fallback.
-+ */
-+ *vpos = 0;
-+ }
-+
-+ return ret;
-+}
-+
-+int vc4_crtc_get_vblank_timestamp(struct drm_device *dev, unsigned int crtc_id,
-+ int *max_error, struct timeval *vblank_time,
-+ unsigned flags)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ struct vc4_crtc *vc4_crtc = vc4->crtc[crtc_id];
-+ struct drm_crtc *crtc = &vc4_crtc->base;
-+ struct drm_crtc_state *state = crtc->state;
-+
-+ /* Helper routine in DRM core does all the work: */
-+ return drm_calc_vbltimestamp_from_scanoutpos(dev, crtc_id, max_error,
-+ vblank_time, flags,
-+ &state->adjusted_mode);
-+}
-+
- static void vc4_crtc_destroy(struct drm_crtc *crtc)
- {
- drm_crtc_cleanup(crtc);
-@@ -535,6 +678,7 @@ static irqreturn_t vc4_crtc_irq_handler(
- irqreturn_t ret = IRQ_NONE;
-
- if (stat & PV_INT_VFP_START) {
-+ vc4_crtc->t_vblank = ktime_get();
- CRTC_WRITE(PV_INTSTAT, PV_INT_VFP_START);
- drm_crtc_handle_vblank(&vc4_crtc->base);
- vc4_crtc_handle_page_flip(vc4_crtc);
-@@ -759,6 +903,22 @@ static void vc4_set_crtc_possible_masks(
- }
- }
-
-+static void
-+vc4_crtc_get_cob_allocation(struct vc4_crtc *vc4_crtc)
-+{
-+ struct drm_device *drm = vc4_crtc->base.dev;
-+ struct vc4_dev *vc4 = to_vc4_dev(drm);
-+ u32 dispbase = HVS_READ(SCALER_DISPBASEX(vc4_crtc->channel));
-+ /* Top/base are supposed to be 4-pixel aligned, but the
-+ * Raspberry Pi firmware fills the low bits (which are
-+ * presumably ignored).
-+ */
-+ u32 top = VC4_GET_FIELD(dispbase, SCALER_DISPBASEX_TOP) & ~3;
-+ u32 base = VC4_GET_FIELD(dispbase, SCALER_DISPBASEX_BASE) & ~3;
-+
-+ vc4_crtc->cob_size = top - base + 4;
-+}
-+
- static int vc4_crtc_bind(struct device *dev, struct device *master, void *data)
- {
- struct platform_device *pdev = to_platform_device(dev);
-@@ -835,6 +995,8 @@ static int vc4_crtc_bind(struct device *
- crtc->cursor = cursor_plane;
- }
-
-+ vc4_crtc_get_cob_allocation(vc4_crtc);
-+
- CRTC_WRITE(PV_INTEN, 0);
- CRTC_WRITE(PV_INTSTAT, PV_INT_VFP_START);
- ret = devm_request_irq(dev, platform_get_irq(pdev, 0),
---- a/drivers/gpu/drm/vc4/vc4_drv.c
-+++ b/drivers/gpu/drm/vc4/vc4_drv.c
-@@ -116,6 +116,8 @@ static struct drm_driver vc4_drm_driver
- .enable_vblank = vc4_enable_vblank,
- .disable_vblank = vc4_disable_vblank,
- .get_vblank_counter = drm_vblank_no_hw_counter,
-+ .get_scanout_position = vc4_crtc_get_scanoutpos,
-+ .get_vblank_timestamp = vc4_crtc_get_vblank_timestamp,
-
- #if defined(CONFIG_DEBUG_FS)
- .debugfs_init = vc4_debugfs_init,
---- a/drivers/gpu/drm/vc4/vc4_drv.h
-+++ b/drivers/gpu/drm/vc4/vc4_drv.h
-@@ -419,6 +419,13 @@ int vc4_enable_vblank(struct drm_device
- void vc4_disable_vblank(struct drm_device *dev, unsigned int crtc_id);
- void vc4_cancel_page_flip(struct drm_crtc *crtc, struct drm_file *file);
- int vc4_crtc_debugfs_regs(struct seq_file *m, void *arg);
-+int vc4_crtc_get_scanoutpos(struct drm_device *dev, unsigned int crtc_id,
-+ unsigned int flags, int *vpos, int *hpos,
-+ ktime_t *stime, ktime_t *etime,
-+ const struct drm_display_mode *mode);
-+int vc4_crtc_get_vblank_timestamp(struct drm_device *dev, unsigned int crtc_id,
-+ int *max_error, struct timeval *vblank_time,
-+ unsigned flags);
-
- /* vc4_debugfs.c */
- int vc4_debugfs_init(struct drm_minor *minor);
---- a/drivers/gpu/drm/vc4/vc4_regs.h
-+++ b/drivers/gpu/drm/vc4/vc4_regs.h
-@@ -368,7 +368,6 @@
- # define SCALER_DISPBKGND_FILL BIT(24)
-
- #define SCALER_DISPSTAT0 0x00000048
--#define SCALER_DISPBASE0 0x0000004c
- # define SCALER_DISPSTATX_MODE_MASK VC4_MASK(31, 30)
- # define SCALER_DISPSTATX_MODE_SHIFT 30
- # define SCALER_DISPSTATX_MODE_DISABLED 0
-@@ -377,6 +376,24 @@
- # define SCALER_DISPSTATX_MODE_EOF 3
- # define SCALER_DISPSTATX_FULL BIT(29)
- # define SCALER_DISPSTATX_EMPTY BIT(28)
-+# define SCALER_DISPSTATX_FRAME_COUNT_MASK VC4_MASK(17, 12)
-+# define SCALER_DISPSTATX_FRAME_COUNT_SHIFT 12
-+# define SCALER_DISPSTATX_LINE_MASK VC4_MASK(11, 0)
-+# define SCALER_DISPSTATX_LINE_SHIFT 0
-+
-+#define SCALER_DISPBASE0 0x0000004c
-+/* Last pixel in the COB (display FIFO memory) allocated to this HVS
-+ * channel. Must be 4-pixel aligned (and thus 4 pixels less than the
-+ * next COB base).
-+ */
-+# define SCALER_DISPBASEX_TOP_MASK VC4_MASK(31, 16)
-+# define SCALER_DISPBASEX_TOP_SHIFT 16
-+/* First pixel in the COB (display FIFO memory) allocated to this HVS
-+ * channel. Must be 4-pixel aligned.
-+ */
-+# define SCALER_DISPBASEX_BASE_MASK VC4_MASK(15, 0)
-+# define SCALER_DISPBASEX_BASE_SHIFT 0
-+
- #define SCALER_DISPCTRL1 0x00000050
- #define SCALER_DISPBKGND1 0x00000054
- #define SCALER_DISPBKGNDX(x) (SCALER_DISPBKGND0 + \
-@@ -387,6 +404,9 @@
- (x) * (SCALER_DISPSTAT1 - \
- SCALER_DISPSTAT0))
- #define SCALER_DISPBASE1 0x0000005c
-+#define SCALER_DISPBASEX(x) (SCALER_DISPBASE0 + \
-+ (x) * (SCALER_DISPBASE1 - \
-+ SCALER_DISPBASE0))
- #define SCALER_DISPCTRL2 0x00000060
- #define SCALER_DISPCTRLX(x) (SCALER_DISPCTRL0 + \
- (x) * (SCALER_DISPCTRL1 - \
diff --git a/target/linux/brcm2708/patches-4.4/0456-drm-vc4-remove-redundant-ret-status-check.patch b/target/linux/brcm2708/patches-4.4/0456-drm-vc4-remove-redundant-ret-status-check.patch
deleted file mode 100644
index bf93afe..0000000
--- a/target/linux/brcm2708/patches-4.4/0456-drm-vc4-remove-redundant-ret-status-check.patch
+++ /dev/null
@@ -1,35 +0,0 @@
-From 2da1a72e0b499cd8a75465f3bc6ab19483ae72c0 Mon Sep 17 00:00:00 2001
-From: Colin Ian King <colin.king at canonical.com>
-Date: Sat, 9 Jul 2016 23:26:03 +0100
-Subject: [PATCH] drm/vc4: remove redundant ret status check
-
-At the current point where ret is being checked for non-zero it has
-not changed since it was initialized to zero, hence the check and the
-label unref are redundant and can be removed.
-
-Signed-off-by: Colin Ian King <colin.king at canonical.com>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit deb4765db386db67626ffd075d8b5eb5fdf9c4f6)
----
- drivers/gpu/drm/vc4/vc4_drv.c | 3 ---
- 1 file changed, 3 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_drv.c
-+++ b/drivers/gpu/drm/vc4/vc4_drv.c
-@@ -233,8 +233,6 @@ static int vc4_drm_bind(struct device *d
- vc4_bo_cache_init(drm);
-
- drm_mode_config_init(drm);
-- if (ret)
-- goto unref;
-
- vc4_gem_init(drm);
-
-@@ -268,7 +266,6 @@ unbind_all:
- component_unbind_all(dev, drm);
- gem_destroy:
- vc4_gem_destroy(drm);
--unref:
- drm_dev_unref(drm);
- vc4_bo_cache_destroy(drm);
- return ret;
diff --git a/target/linux/brcm2708/patches-4.4/0457-drm-vc4-add-extern-C-guard-for-the-UAPI-header.patch b/target/linux/brcm2708/patches-4.4/0457-drm-vc4-add-extern-C-guard-for-the-UAPI-header.patch
deleted file mode 100644
index 13b3795..0000000
--- a/target/linux/brcm2708/patches-4.4/0457-drm-vc4-add-extern-C-guard-for-the-UAPI-header.patch
+++ /dev/null
@@ -1,34 +0,0 @@
-From 6591e6d9cd731912af998941de8ce4218bd5c278 Mon Sep 17 00:00:00 2001
-From: Emil Velikov <emil.l.velikov at gmail.com>
-Date: Thu, 7 Apr 2016 19:36:57 +0100
-Subject: [PATCH] drm/vc4: add extern C guard for the UAPI header
-
-Cc: Eric Anholt <eric at anholt.net>
-Signed-off-by: Emil Velikov <emil.l.velikov at gmail.com>
-(cherry picked from commit 6a982350f892c286c645a6fe0e1da1f869a0c43f)
----
- include/uapi/drm/vc4_drm.h | 8 ++++++++
- 1 file changed, 8 insertions(+)
-
---- a/include/uapi/drm/vc4_drm.h
-+++ b/include/uapi/drm/vc4_drm.h
-@@ -26,6 +26,10 @@
-
- #include "drm.h"
-
-+#if defined(__cplusplus)
-+extern "C" {
-+#endif
-+
- #define DRM_VC4_SUBMIT_CL 0x00
- #define DRM_VC4_WAIT_SEQNO 0x01
- #define DRM_VC4_WAIT_BO 0x02
-@@ -276,4 +280,8 @@ struct drm_vc4_get_hang_state {
- __u32 pad[16];
- };
-
-+#if defined(__cplusplus)
-+}
-+#endif
-+
- #endif /* _UAPI_VC4_DRM_H_ */
diff --git a/target/linux/brcm2708/patches-4.4/0458-drm-vc4-Fix-definition-of-QPU_R_MS_REV_FLAGS.patch b/target/linux/brcm2708/patches-4.4/0458-drm-vc4-Fix-definition-of-QPU_R_MS_REV_FLAGS.patch
deleted file mode 100644
index 28281fe..0000000
--- a/target/linux/brcm2708/patches-4.4/0458-drm-vc4-Fix-definition-of-QPU_R_MS_REV_FLAGS.patch
+++ /dev/null
@@ -1,25 +0,0 @@
-From 0161e66f52450ec28b32ac82cce3ad2b9f8f07c3 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 4 Jul 2016 12:59:18 -0700
-Subject: [PATCH] drm/vc4: Fix definition of QPU_R_MS_REV_FLAGS
-
-We don't use it in shader validation currently, so it had no effect,
-but best to fix it anyway in case we do some day.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 20e48fd6a9252e21528c7e39b874c8fdca97f25a)
----
- drivers/gpu/drm/vc4/vc4_qpu_defines.h | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/gpu/drm/vc4/vc4_qpu_defines.h
-+++ b/drivers/gpu/drm/vc4/vc4_qpu_defines.h
-@@ -70,7 +70,7 @@ enum qpu_raddr {
- QPU_R_ELEM_QPU = 38,
- QPU_R_NOP,
- QPU_R_XY_PIXEL_COORD = 41,
-- QPU_R_MS_REV_FLAGS = 41,
-+ QPU_R_MS_REV_FLAGS = 42,
- QPU_R_VPM = 48,
- QPU_R_VPM_LD_BUSY,
- QPU_R_VPM_LD_WAIT,
diff --git a/target/linux/brcm2708/patches-4.4/0459-drm-vc4-Fix-a-the-the-typo-in-a-comment.patch b/target/linux/brcm2708/patches-4.4/0459-drm-vc4-Fix-a-the-the-typo-in-a-comment.patch
deleted file mode 100644
index 2339c51..0000000
--- a/target/linux/brcm2708/patches-4.4/0459-drm-vc4-Fix-a-the-the-typo-in-a-comment.patch
+++ /dev/null
@@ -1,22 +0,0 @@
-From ca9c813142d6876340ffbd3eb12be28c0a232cfa Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Sat, 2 Jul 2016 09:58:41 -0700
-Subject: [PATCH] drm/vc4: Fix a "the the" typo in a comment.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit a20d5fa61c32a0c94d237da642326db2ef3c7433)
----
- drivers/gpu/drm/vc4/vc4_validate_shaders.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/gpu/drm/vc4/vc4_validate_shaders.c
-+++ b/drivers/gpu/drm/vc4/vc4_validate_shaders.c
-@@ -162,7 +162,7 @@ check_tmu_write(uint64_t inst,
- return false;
- }
-
-- /* We assert that the the clamped address is the first
-+ /* We assert that the clamped address is the first
- * argument, and the UBO base address is the second argument.
- * This is arbitrary, but simpler than supporting flipping the
- * two either way.
diff --git a/target/linux/brcm2708/patches-4.4/0460-drm-vc4-Return-EBUSY-if-there-s-already-a-pending-fl.patch b/target/linux/brcm2708/patches-4.4/0460-drm-vc4-Return-EBUSY-if-there-s-already-a-pending-fl.patch
deleted file mode 100644
index ae76d25..0000000
--- a/target/linux/brcm2708/patches-4.4/0460-drm-vc4-Return-EBUSY-if-there-s-already-a-pending-fl.patch
+++ /dev/null
@@ -1,44 +0,0 @@
-From 52367e61f8707fe5e22aabf3c769e27f11aa3300 Mon Sep 17 00:00:00 2001
-From: Robert Foss <robert.foss at collabora.com>
-Date: Tue, 3 May 2016 13:48:20 -0400
-Subject: [PATCH] drm/vc4: Return -EBUSY if there's already a pending flip
- event.
-
-As per the documentation in drm_crtc.h, atomic_commit should return
--EBUSY if an asynchronous update is requested and there is an earlier
-update pending.
-
-v2: Rebase on the s/async/nonblock/ change.
-
-Signed-off-by: Robert Foss <robert.foss at collabora.com>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit e7c31f6f25b84fed961dc0dce6248878527693ae)
----
- drivers/gpu/drm/vc4/vc4_kms.c | 16 ++++++++++++----
- 1 file changed, 12 insertions(+), 4 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_kms.c
-+++ b/drivers/gpu/drm/vc4/vc4_kms.c
-@@ -119,10 +119,18 @@ static int vc4_atomic_commit(struct drm_
- return -ENOMEM;
-
- /* Make sure that any outstanding modesets have finished. */
-- ret = down_interruptible(&vc4->async_modeset);
-- if (ret) {
-- kfree(c);
-- return ret;
-+ if (nonblock) {
-+ ret = down_trylock(&vc4->async_modeset);
-+ if (ret) {
-+ kfree(c);
-+ return -EBUSY;
-+ }
-+ } else {
-+ ret = down_interruptible(&vc4->async_modeset);
-+ if (ret) {
-+ kfree(c);
-+ return ret;
-+ }
- }
-
- ret = drm_atomic_helper_prepare_planes(dev, state);
diff --git a/target/linux/brcm2708/patches-4.4/0461-config-Enable-SENSORS_LM75.patch b/target/linux/brcm2708/patches-4.4/0461-config-Enable-SENSORS_LM75.patch
deleted file mode 100644
index f4b3895..0000000
--- a/target/linux/brcm2708/patches-4.4/0461-config-Enable-SENSORS_LM75.patch
+++ /dev/null
@@ -1,30 +0,0 @@
-From ed4550946339c282b938769b3608416f98fe5d09 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Fri, 12 Aug 2016 17:12:32 +0100
-Subject: [PATCH] config: Enable SENSORS_LM75
-
----
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 2 files changed, 2 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -642,6 +642,7 @@ CONFIG_BATTERY_DS2760=m
- CONFIG_POWER_RESET=y
- CONFIG_POWER_RESET_GPIO=y
- CONFIG_HWMON=m
-+CONFIG_SENSORS_LM75=m
- CONFIG_SENSORS_SHT21=m
- CONFIG_SENSORS_SHTC1=m
- CONFIG_THERMAL=y
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -634,6 +634,7 @@ CONFIG_BATTERY_DS2760=m
- CONFIG_POWER_RESET=y
- CONFIG_POWER_RESET_GPIO=y
- CONFIG_HWMON=m
-+CONFIG_SENSORS_LM75=m
- CONFIG_SENSORS_SHT21=m
- CONFIG_SENSORS_SHTC1=m
- CONFIG_THERMAL=y
diff --git a/target/linux/brcm2708/patches-4.4/0462-config-Enable-SERIAL_SC16IS7XX.patch b/target/linux/brcm2708/patches-4.4/0462-config-Enable-SERIAL_SC16IS7XX.patch
deleted file mode 100644
index ae9a489..0000000
--- a/target/linux/brcm2708/patches-4.4/0462-config-Enable-SERIAL_SC16IS7XX.patch
+++ /dev/null
@@ -1,30 +0,0 @@
-From 3c1c34126ec31883a014aca8bf929508d85b30b0 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Fri, 12 Aug 2016 17:00:18 +0100
-Subject: [PATCH] config: Enable SERIAL_SC16IS7XX
-
----
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 2 files changed, 2 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -600,6 +600,7 @@ CONFIG_SERIAL_8250_RUNTIME_UARTS=0
- CONFIG_SERIAL_AMBA_PL011=y
- CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
- CONFIG_SERIAL_OF_PLATFORM=y
-+CONFIG_SERIAL_SC16IS7XX=m
- CONFIG_TTY_PRINTK=y
- CONFIG_HW_RANDOM=y
- CONFIG_RAW_DRIVER=y
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -593,6 +593,7 @@ CONFIG_SERIAL_8250_RUNTIME_UARTS=0
- CONFIG_SERIAL_AMBA_PL011=y
- CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
- CONFIG_SERIAL_OF_PLATFORM=y
-+CONFIG_SERIAL_SC16IS7XX=m
- CONFIG_TTY_PRINTK=y
- CONFIG_HW_RANDOM=y
- CONFIG_RAW_DRIVER=y
diff --git a/target/linux/brcm2708/patches-4.4/0463-snd-bcm2835-Don-t-allow-responses-from-VC-to-be-inte.patch b/target/linux/brcm2708/patches-4.4/0463-snd-bcm2835-Don-t-allow-responses-from-VC-to-be-inte.patch
deleted file mode 100644
index 561a0ac..0000000
--- a/target/linux/brcm2708/patches-4.4/0463-snd-bcm2835-Don-t-allow-responses-from-VC-to-be-inte.patch
+++ /dev/null
@@ -1,63 +0,0 @@
-From ba90aec87bb438f8e92f9263600485ddff232975 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Fri, 12 Aug 2016 15:46:21 +0100
-Subject: [PATCH] snd-bcm2835: Don't allow responses from VC to be interrupted
- by user signals
-
-There should always be a response, and retry after a signal interruption is not handled, so don't report
-we are interruptible.
-
-See: https://github.com/raspberrypi/linux/issues/1560
----
- sound/arm/bcm2835-vchiq.c | 25 ++++++-------------------
- 1 file changed, 6 insertions(+), 19 deletions(-)
-
---- a/sound/arm/bcm2835-vchiq.c
-+++ b/sound/arm/bcm2835-vchiq.c
-@@ -511,12 +511,7 @@ static int bcm2835_audio_set_ctls_chan(b
- }
-
- /* We are expecting a reply from the videocore */
-- ret = wait_for_completion_interruptible(&instance->msg_avail_comp);
-- if (ret) {
-- LOG_DBG("%s: failed on waiting for event (status=%d)\n",
-- __func__, success);
-- goto unlock;
-- }
-+ wait_for_completion(&instance->msg_avail_comp);
-
- if (instance->result != 0) {
- LOG_ERR("%s: result=%d\n", __func__, instance->result);
-@@ -615,12 +610,7 @@ int bcm2835_audio_set_params(bcm2835_als
- }
-
- /* We are expecting a reply from the videocore */
-- ret = wait_for_completion_interruptible(&instance->msg_avail_comp);
-- if (ret) {
-- LOG_DBG("%s: failed on waiting for event (status=%d)\n",
-- __func__, success);
-- goto unlock;
-- }
-+ wait_for_completion(&instance->msg_avail_comp);
-
- if (instance->result != 0) {
- LOG_ERR("%s: result=%d", __func__, instance->result);
-@@ -761,14 +751,11 @@ int bcm2835_audio_close(bcm2835_alsa_str
- goto unlock;
- }
-
-- ret = wait_for_completion_interruptible(&instance->msg_avail_comp);
-- if (ret) {
-- LOG_DBG("%s: failed on waiting for event (status=%d)\n",
-- __func__, success);
-- goto unlock;
-- }
-+ /* We are expecting a reply from the videocore */
-+ wait_for_completion(&instance->msg_avail_comp);
-+
- if (instance->result != 0) {
-- LOG_ERR("%s: failed result (status=%d)\n",
-+ LOG_ERR("%s: failed result (result=%d)\n",
- __func__, instance->result);
-
- ret = -1;
diff --git a/target/linux/brcm2708/patches-4.4/0464-BCM270X-Connect-V3D-to-its-power-domain.patch b/target/linux/brcm2708/patches-4.4/0464-BCM270X-Connect-V3D-to-its-power-domain.patch
deleted file mode 100644
index 28784be..0000000
--- a/target/linux/brcm2708/patches-4.4/0464-BCM270X-Connect-V3D-to-its-power-domain.patch
+++ /dev/null
@@ -1,23 +0,0 @@
-From 788b6642156c9128a640bb1cc7d14625a0ab6caa Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 12 Aug 2016 10:15:34 -0700
-Subject: [PATCH] BCM270X: Connect V3D to its power domain.
-
-We were doing this with manual firmware calls before, but to backport
-runtime PM we want to be using a proper power domain.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- arch/arm/boot/dts/bcm2708_common.dtsi | 1 +
- 1 file changed, 1 insertion(+)
-
---- a/arch/arm/boot/dts/bcm2708_common.dtsi
-+++ b/arch/arm/boot/dts/bcm2708_common.dtsi
-@@ -366,6 +366,7 @@
- v3d: v3d at 7ec00000 {
- compatible = "brcm,vc4-v3d";
- reg = <0x7ec00000 0x1000>;
-+ power-domains = <&power RPI_POWER_DOMAIN_V3D>;
- status = "disabled";
- };
-
diff --git a/target/linux/brcm2708/patches-4.4/0465-drm-vc4-Enable-runtime-PM.patch b/target/linux/brcm2708/patches-4.4/0465-drm-vc4-Enable-runtime-PM.patch
deleted file mode 100644
index 657dde3..0000000
--- a/target/linux/brcm2708/patches-4.4/0465-drm-vc4-Enable-runtime-PM.patch
+++ /dev/null
@@ -1,205 +0,0 @@
-From 212a4df279413e1d9b8c3f5ab25dadf637df3f09 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 5 Feb 2016 17:41:49 -0800
-Subject: [PATCH] drm/vc4: Enable runtime PM.
-
-This may actually get us a feature that the closed driver didn't have:
-turning off the GPU in between rendering jobs, while the V3D device is
-still opened by the client.
-
-There may be some tuning to be applied here to use autosuspend so that
-we don't bounce the device's power so much, but in steady-state
-GPU-bound rendering we keep the power on (since we keep multiple jobs
-outstanding) and even if we power cycle on every job we can still
-manage at least 680 fps.
-
-More importantly, though, runtime PM will allow us to power off the
-device to do a GPU reset.
-
-v2: Switch #ifdef to CONFIG_PM not CONFIG_PM_SLEEP (caught by kbuild
- test robot)
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 001bdb55d9eb72a9e2d5b623bacfc52da74ae03e)
----
- drivers/gpu/drm/vc4/vc4_drv.h | 1 +
- drivers/gpu/drm/vc4/vc4_gem.c | 10 ++++++++
- drivers/gpu/drm/vc4/vc4_v3d.c | 59 ++++++++++++++++++++++++++-----------------
- 3 files changed, 47 insertions(+), 23 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_drv.h
-+++ b/drivers/gpu/drm/vc4/vc4_drv.h
-@@ -155,6 +155,7 @@ struct vc4_seqno_cb {
- };
-
- struct vc4_v3d {
-+ struct vc4_dev *vc4;
- struct platform_device *pdev;
- void __iomem *regs;
- };
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -23,6 +23,7 @@
-
- #include <linux/module.h>
- #include <linux/platform_device.h>
-+#include <linux/pm_runtime.h>
- #include <linux/device.h>
- #include <linux/io.h>
-
-@@ -689,6 +690,7 @@ fail:
- static void
- vc4_complete_exec(struct drm_device *dev, struct vc4_exec_info *exec)
- {
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
- unsigned i;
-
- /* Need the struct lock for drm_gem_object_unreference(). */
-@@ -707,6 +709,8 @@ vc4_complete_exec(struct drm_device *dev
- }
- mutex_unlock(&dev->struct_mutex);
-
-+ pm_runtime_put(&vc4->v3d->pdev->dev);
-+
- kfree(exec);
- }
-
-@@ -860,6 +864,12 @@ vc4_submit_cl_ioctl(struct drm_device *d
- return -ENOMEM;
- }
-
-+ ret = pm_runtime_get_sync(&vc4->v3d->pdev->dev);
-+ if (ret < 0) {
-+ kfree(exec);
-+ return ret;
-+ }
-+
- exec->args = args;
- INIT_LIST_HEAD(&exec->unref_list);
-
---- a/drivers/gpu/drm/vc4/vc4_v3d.c
-+++ b/drivers/gpu/drm/vc4/vc4_v3d.c
-@@ -17,7 +17,7 @@
- */
-
- #include "linux/component.h"
--#include "soc/bcm2835/raspberrypi-firmware.h"
-+#include "linux/pm_runtime.h"
- #include "vc4_drv.h"
- #include "vc4_regs.h"
-
-@@ -145,22 +145,6 @@ int vc4_v3d_debugfs_ident(struct seq_fil
- }
- #endif /* CONFIG_DEBUG_FS */
-
--/*
-- * Asks the firmware to turn on power to the V3D engine.
-- *
-- * This may be doable with just the clocks interface, though this
-- * packet does some other register setup from the firmware, too.
-- */
--int
--vc4_v3d_set_power(struct vc4_dev *vc4, bool on)
--{
-- u32 packet = on;
--
-- return rpi_firmware_property(vc4->firmware,
-- RPI_FIRMWARE_SET_ENABLE_QPU,
-- &packet, sizeof(packet));
--}
--
- static void vc4_v3d_init_hw(struct drm_device *dev)
- {
- struct vc4_dev *vc4 = to_vc4_dev(dev);
-@@ -172,6 +156,29 @@ static void vc4_v3d_init_hw(struct drm_d
- V3D_WRITE(V3D_VPMBASE, 0);
- }
-
-+#ifdef CONFIG_PM
-+static int vc4_v3d_runtime_suspend(struct device *dev)
-+{
-+ struct vc4_v3d *v3d = dev_get_drvdata(dev);
-+ struct vc4_dev *vc4 = v3d->vc4;
-+
-+ vc4_irq_uninstall(vc4->dev);
-+
-+ return 0;
-+}
-+
-+static int vc4_v3d_runtime_resume(struct device *dev)
-+{
-+ struct vc4_v3d *v3d = dev_get_drvdata(dev);
-+ struct vc4_dev *vc4 = v3d->vc4;
-+
-+ vc4_v3d_init_hw(vc4->dev);
-+ vc4_irq_postinstall(vc4->dev);
-+
-+ return 0;
-+}
-+#endif
-+
- static int vc4_v3d_bind(struct device *dev, struct device *master, void *data)
- {
- struct platform_device *pdev = to_platform_device(dev);
-@@ -184,6 +191,8 @@ static int vc4_v3d_bind(struct device *d
- if (!v3d)
- return -ENOMEM;
-
-+ dev_set_drvdata(dev, v3d);
-+
- v3d->pdev = pdev;
-
- v3d->regs = vc4_ioremap_regs(pdev, 0);
-@@ -191,10 +200,7 @@ static int vc4_v3d_bind(struct device *d
- return PTR_ERR(v3d->regs);
-
- vc4->v3d = v3d;
--
-- ret = vc4_v3d_set_power(vc4, true);
-- if (ret)
-- return ret;
-+ v3d->vc4 = vc4;
-
- if (V3D_READ(V3D_IDENT0) != V3D_EXPECTED_IDENT0) {
- DRM_ERROR("V3D_IDENT0 read 0x%08x instead of 0x%08x\n",
-@@ -216,6 +222,8 @@ static int vc4_v3d_bind(struct device *d
- return ret;
- }
-
-+ pm_runtime_enable(dev);
-+
- return 0;
- }
-
-@@ -225,6 +233,8 @@ static void vc4_v3d_unbind(struct device
- struct drm_device *drm = dev_get_drvdata(master);
- struct vc4_dev *vc4 = to_vc4_dev(drm);
-
-+ pm_runtime_disable(dev);
-+
- drm_irq_uninstall(drm);
-
- /* Disable the binner's overflow memory address, so the next
-@@ -234,11 +244,13 @@ static void vc4_v3d_unbind(struct device
- V3D_WRITE(V3D_BPOA, 0);
- V3D_WRITE(V3D_BPOS, 0);
-
-- vc4_v3d_set_power(vc4, false);
--
- vc4->v3d = NULL;
- }
-
-+static const struct dev_pm_ops vc4_v3d_pm_ops = {
-+ SET_RUNTIME_PM_OPS(vc4_v3d_runtime_suspend, vc4_v3d_runtime_resume, NULL)
-+};
-+
- static const struct component_ops vc4_v3d_ops = {
- .bind = vc4_v3d_bind,
- .unbind = vc4_v3d_unbind,
-@@ -267,5 +279,6 @@ struct platform_driver vc4_v3d_driver =
- .driver = {
- .name = "vc4_v3d",
- .of_match_table = vc4_v3d_dt_match,
-+ .pm = &vc4_v3d_pm_ops,
- },
- };
diff --git a/target/linux/brcm2708/patches-4.4/0466-drm-vc4-Drop-firmware-node-getting-now-that-we-use-t.patch b/target/linux/brcm2708/patches-4.4/0466-drm-vc4-Drop-firmware-node-getting-now-that-we-use-t.patch
deleted file mode 100644
index b0b5c3e..0000000
--- a/target/linux/brcm2708/patches-4.4/0466-drm-vc4-Drop-firmware-node-getting-now-that-we-use-t.patch
+++ /dev/null
@@ -1,54 +0,0 @@
-From 0e305a4094e739a5b474c080b4a0b88dac3dbd48 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 12 Aug 2016 10:45:04 -0700
-Subject: [PATCH] drm/vc4: Drop firmware node getting now that we use the power
- domain.
-
----
- drivers/gpu/drm/vc4/vc4_drv.c | 10 ----------
- drivers/gpu/drm/vc4/vc4_drv.h | 1 -
- 2 files changed, 11 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_drv.c
-+++ b/drivers/gpu/drm/vc4/vc4_drv.c
-@@ -15,7 +15,6 @@
- #include <linux/module.h>
- #include <linux/of_platform.h>
- #include <linux/platform_device.h>
--#include <soc/bcm2835/raspberrypi-firmware.h>
- #include "drm_fb_cma_helper.h"
-
- #include "uapi/drm/vc4_drm.h"
-@@ -204,7 +203,6 @@ static int vc4_drm_bind(struct device *d
- struct drm_device *drm;
- struct drm_connector *connector;
- struct vc4_dev *vc4;
-- struct device_node *firmware_node;
- int ret = 0;
-
- dev->coherent_dma_mask = DMA_BIT_MASK(32);
-@@ -213,14 +211,6 @@ static int vc4_drm_bind(struct device *d
- if (!vc4)
- return -ENOMEM;
-
-- firmware_node = of_parse_phandle(dev->of_node, "firmware", 0);
-- vc4->firmware = rpi_firmware_get(firmware_node);
-- if (!vc4->firmware) {
-- DRM_DEBUG("Failed to get Raspberry Pi firmware reference.\n");
-- return -EPROBE_DEFER;
-- }
-- of_node_put(firmware_node);
--
- drm = drm_dev_alloc(&vc4_drm_driver, dev);
- if (!drm)
- return -ENOMEM;
---- a/drivers/gpu/drm/vc4/vc4_drv.h
-+++ b/drivers/gpu/drm/vc4/vc4_drv.h
-@@ -23,7 +23,6 @@ struct vc4_dev {
- struct vc4_dsi *dsi1;
-
- struct drm_fbdev_cma *fbdev;
-- struct rpi_firmware *firmware;
-
- struct vc4_hang_state *hang_state;
-
diff --git a/target/linux/brcm2708/patches-4.4/0467-drm-vc4-Use-runtime-PM-to-power-cycle-the-device-whe.patch b/target/linux/brcm2708/patches-4.4/0467-drm-vc4-Use-runtime-PM-to-power-cycle-the-device-whe.patch
deleted file mode 100644
index 6f28800..0000000
--- a/target/linux/brcm2708/patches-4.4/0467-drm-vc4-Use-runtime-PM-to-power-cycle-the-device-whe.patch
+++ /dev/null
@@ -1,102 +0,0 @@
-From a933cf6cc414d067087f311598e4acd42bc4f6d2 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 8 Feb 2016 12:59:02 -0800
-Subject: [PATCH] drm/vc4: Use runtime PM to power cycle the device when the
- GPU hangs.
-
-This gets us functional GPU reset again, like we had until a refactor
-at merge time. Tested with a little patch to stuff in a broken binner
-job every 100 frames.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 36cb6253f9383fd9a59ee7b8458c6232ef48577c)
----
- drivers/gpu/drm/vc4/vc4_drv.h | 6 +++++-
- drivers/gpu/drm/vc4/vc4_gem.c | 26 +++++++++++++++++++++-----
- 2 files changed, 26 insertions(+), 6 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_drv.h
-+++ b/drivers/gpu/drm/vc4/vc4_drv.h
-@@ -104,6 +104,11 @@ struct vc4_dev {
- struct vc4_bo *overflow_mem;
- struct work_struct overflow_mem_work;
-
-+ int power_refcount;
-+
-+ /* Mutex controlling the power refcount. */
-+ struct mutex power_lock;
-+
- struct {
- struct timer_list timer;
- struct work_struct reset_work;
-@@ -495,7 +500,6 @@ void vc4_plane_async_set_fb(struct drm_p
- extern struct platform_driver vc4_v3d_driver;
- int vc4_v3d_debugfs_ident(struct seq_file *m, void *unused);
- int vc4_v3d_debugfs_regs(struct seq_file *m, void *unused);
--int vc4_v3d_set_power(struct vc4_dev *vc4, bool on);
-
- /* vc4_validate.c */
- int
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -261,8 +261,16 @@ vc4_reset(struct drm_device *dev)
- struct vc4_dev *vc4 = to_vc4_dev(dev);
-
- DRM_INFO("Resetting GPU.\n");
-- vc4_v3d_set_power(vc4, false);
-- vc4_v3d_set_power(vc4, true);
-+
-+ mutex_lock(&vc4->power_lock);
-+ if (vc4->power_refcount) {
-+ /* Power the device off and back on the by dropping the
-+ * reference on runtime PM.
-+ */
-+ pm_runtime_put_sync_suspend(&vc4->v3d->pdev->dev);
-+ pm_runtime_get_sync(&vc4->v3d->pdev->dev);
-+ }
-+ mutex_unlock(&vc4->power_lock);
-
- vc4_irq_reset(dev);
-
-@@ -709,7 +717,10 @@ vc4_complete_exec(struct drm_device *dev
- }
- mutex_unlock(&dev->struct_mutex);
-
-- pm_runtime_put(&vc4->v3d->pdev->dev);
-+ mutex_lock(&vc4->power_lock);
-+ if (--vc4->power_refcount == 0)
-+ pm_runtime_put(&vc4->v3d->pdev->dev);
-+ mutex_unlock(&vc4->power_lock);
-
- kfree(exec);
- }
-@@ -851,7 +862,7 @@ vc4_submit_cl_ioctl(struct drm_device *d
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct drm_vc4_submit_cl *args = data;
- struct vc4_exec_info *exec;
-- int ret;
-+ int ret = 0;
-
- if ((args->flags & ~VC4_SUBMIT_CL_USE_CLEAR_COLOR) != 0) {
- DRM_ERROR("Unknown flags: 0x%02x\n", args->flags);
-@@ -864,7 +875,10 @@ vc4_submit_cl_ioctl(struct drm_device *d
- return -ENOMEM;
- }
-
-- ret = pm_runtime_get_sync(&vc4->v3d->pdev->dev);
-+ mutex_lock(&vc4->power_lock);
-+ if (vc4->power_refcount++ == 0)
-+ ret = pm_runtime_get_sync(&vc4->v3d->pdev->dev);
-+ mutex_unlock(&vc4->power_lock);
- if (ret < 0) {
- kfree(exec);
- return ret;
-@@ -925,6 +939,8 @@ vc4_gem_init(struct drm_device *dev)
- (unsigned long)dev);
-
- INIT_WORK(&vc4->job_done_work, vc4_job_done_work);
-+
-+ mutex_init(&vc4->power_lock);
- }
-
- void
diff --git a/target/linux/brcm2708/patches-4.4/0468-drm-panel-Drop-debug-printf-from-the-Raspberry-Pi-to.patch b/target/linux/brcm2708/patches-4.4/0468-drm-panel-Drop-debug-printf-from-the-Raspberry-Pi-to.patch
deleted file mode 100644
index ec9fb21..0000000
--- a/target/linux/brcm2708/patches-4.4/0468-drm-panel-Drop-debug-printf-from-the-Raspberry-Pi-to.patch
+++ /dev/null
@@ -1,21 +0,0 @@
-From 2ef55e3ffd5e23167a868b21779746c28ae31ed0 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 12 Aug 2016 10:55:53 -0700
-Subject: [PATCH] drm/panel: Drop debug printf from the Raspberry Pi
- touchscreen.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/panel/panel-raspberrypi-touchscreen.c | 1 -
- 1 file changed, 1 deletion(-)
-
---- a/drivers/gpu/drm/panel/panel-raspberrypi-touchscreen.c
-+++ b/drivers/gpu/drm/panel/panel-raspberrypi-touchscreen.c
-@@ -106,7 +106,6 @@ struct regdump {
- static int rpi_touchscreen_disable(struct drm_panel *panel)
- {
- struct rpi_touchscreen *ts = panel_to_ts(panel);
-- pr_err("disable\n");
-
- if (!ts->enabled)
- return 0;
diff --git a/target/linux/brcm2708/patches-4.4/0469-drm-vc4-Replace-HDMI-force-connected-with-an-EDID-pr.patch b/target/linux/brcm2708/patches-4.4/0469-drm-vc4-Replace-HDMI-force-connected-with-an-EDID-pr.patch
deleted file mode 100644
index 2c7ebbd..0000000
--- a/target/linux/brcm2708/patches-4.4/0469-drm-vc4-Replace-HDMI-force-connected-with-an-EDID-pr.patch
+++ /dev/null
@@ -1,42 +0,0 @@
-From 24e0c9aecebc158105c71f5f17b54a66c88c30f6 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 12 Aug 2016 10:57:41 -0700
-Subject: [PATCH] drm/vc4: Replace HDMI force-connected with an EDID probe.
-
-The force-connected started out because I didn't know how to read the
-HPD pin successfully, which required the hpd_active_low check and
-getting the correct active level into the DTs. It stayed because we
-don't have the Pi3's HPD line exposed to Linux, so this was the only
-way to bring up graphics on it.
-
-However, with the DSI panel support now present, users want to be able
-to run DSI-only systems, and forcing HDMI on is interfering with
-default screen configurations. Work around the Pi3's missing HPD by
-probing the DDC on I2C and see if it's present at all.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_hdmi.c | 5 +++--
- 1 file changed, 3 insertions(+), 2 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_hdmi.c
-+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
-@@ -166,8 +166,6 @@ vc4_hdmi_connector_detect(struct drm_con
- struct drm_device *dev = connector->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
-
-- return connector_status_connected;
--
- if (vc4->hdmi->hpd_gpio) {
- if (gpio_get_value_cansleep(vc4->hdmi->hpd_gpio) ^
- vc4->hdmi->hpd_active_low)
-@@ -176,6 +174,9 @@ vc4_hdmi_connector_detect(struct drm_con
- return connector_status_disconnected;
- }
-
-+ if (drm_probe_ddc(vc4->hdmi->ddc))
-+ return connector_status_connected;
-+
- if (HDMI_READ(VC4_HDMI_HOTPLUG) & VC4_HDMI_HOTPLUG_CONNECTED)
- return connector_status_connected;
- else
diff --git a/target/linux/brcm2708/patches-4.4/0470-net-ethernet-enc28j60-add-device-tree-support.patch b/target/linux/brcm2708/patches-4.4/0470-net-ethernet-enc28j60-add-device-tree-support.patch
deleted file mode 100644
index 9a0b2dc..0000000
--- a/target/linux/brcm2708/patches-4.4/0470-net-ethernet-enc28j60-add-device-tree-support.patch
+++ /dev/null
@@ -1,143 +0,0 @@
-From bfd9d92f219cb1dc8899d0f82d6ad2f966e2ef61 Mon Sep 17 00:00:00 2001
-From: Michael Heimpold <mhei at heimpold.de>
-Date: Thu, 28 Apr 2016 22:06:15 +0200
-Subject: [PATCH] net: ethernet: enc28j60: add device tree support
-
-(Upstream commit 2dd355a007e44960ec049c75920ddb6778fec9ee)
-
-The following patch adds the required match table for device tree support
-(and while at, fix the indent). It's also possible to specify the
-MAC address in the DT blob.
-
-Also add the corresponding binding documentation file.
-
-Signed-off-by: Michael Heimpold <mhei at heimpold.de>
-Signed-off-by: David S. Miller <davem at davemloft.net>
----
- .../devicetree/bindings/net/microchip,enc28j60.txt | 59 ++++++++++++++++++++++
- drivers/net/ethernet/microchip/enc28j60.c | 21 +++++---
- 2 files changed, 73 insertions(+), 7 deletions(-)
- create mode 100644 Documentation/devicetree/bindings/net/microchip,enc28j60.txt
-
---- /dev/null
-+++ b/Documentation/devicetree/bindings/net/microchip,enc28j60.txt
-@@ -0,0 +1,59 @@
-+* Microchip ENC28J60
-+
-+This is a standalone 10 MBit ethernet controller with SPI interface.
-+
-+For each device connected to a SPI bus, define a child node within
-+the SPI master node.
-+
-+Required properties:
-+- compatible: Should be "microchip,enc28j60"
-+- reg: Specify the SPI chip select the ENC28J60 is wired to
-+- interrupt-parent: Specify the phandle of the source interrupt, see interrupt
-+ binding documentation for details. Usually this is the GPIO bank
-+ the interrupt line is wired to.
-+- interrupts: Specify the interrupt index within the interrupt controller (referred
-+ to above in interrupt-parent) and interrupt type. The ENC28J60 natively
-+ generates falling edge interrupts, however, additional board logic
-+ might invert the signal.
-+- pinctrl-names: List of assigned state names, see pinctrl binding documentation.
-+- pinctrl-0: List of phandles to configure the GPIO pin used as interrupt line,
-+ see also generic and your platform specific pinctrl binding
-+ documentation.
-+
-+Optional properties:
-+- spi-max-frequency: Maximum frequency of the SPI bus when accessing the ENC28J60.
-+ According to the ENC28J80 datasheet, the chip allows a maximum of 20 MHz, however,
-+ board designs may need to limit this value.
-+- local-mac-address: See ethernet.txt in the same directory.
-+
-+
-+Example (for NXP i.MX28 with pin control stuff for GPIO irq):
-+
-+ ssp2: ssp at 80014000 {
-+ compatible = "fsl,imx28-spi";
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&spi2_pins_b &spi2_sck_cfg>;
-+ status = "okay";
-+
-+ enc28j60: ethernet at 0 {
-+ compatible = "microchip,enc28j60";
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&enc28j60_pins>;
-+ reg = <0>;
-+ interrupt-parent = <&gpio3>;
-+ interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
-+ spi-max-frequency = <12000000>;
-+ };
-+ };
-+
-+ pinctrl at 80018000 {
-+ enc28j60_pins: enc28j60_pins at 0 {
-+ reg = <0>;
-+ fsl,pinmux-ids = <
-+ MX28_PAD_AUART0_RTS__GPIO_3_3 /* Interrupt */
-+ >;
-+ fsl,drive-strength = <MXS_DRIVE_4mA>;
-+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
-+ fsl,pull-up = <MXS_PULL_DISABLE>;
-+ };
-+ };
---- a/drivers/net/ethernet/microchip/enc28j60.c
-+++ b/drivers/net/ethernet/microchip/enc28j60.c
-@@ -28,11 +28,12 @@
- #include <linux/skbuff.h>
- #include <linux/delay.h>
- #include <linux/spi/spi.h>
-+#include <linux/of_net.h>
-
- #include "enc28j60_hw.h"
-
- #define DRV_NAME "enc28j60"
--#define DRV_VERSION "1.01"
-+#define DRV_VERSION "1.02"
-
- #define SPI_OPLEN 1
-
-@@ -1544,6 +1545,7 @@ static int enc28j60_probe(struct spi_dev
- {
- struct net_device *dev;
- struct enc28j60_net *priv;
-+ const void *macaddr;
- int ret = 0;
-
- if (netif_msg_drv(&debug))
-@@ -1575,7 +1577,12 @@ static int enc28j60_probe(struct spi_dev
- ret = -EIO;
- goto error_irq;
- }
-- eth_hw_addr_random(dev);
-+
-+ macaddr = of_get_mac_address(spi->dev.of_node);
-+ if (macaddr)
-+ ether_addr_copy(dev->dev_addr, macaddr);
-+ else
-+ eth_hw_addr_random(dev);
- enc28j60_set_hw_macaddr(dev);
-
- /* Board setup must set the relevant edge trigger type;
-@@ -1630,16 +1637,16 @@ static int enc28j60_remove(struct spi_de
- return 0;
- }
-
--static const struct of_device_id enc28j60_of_match[] = {
-- { .compatible = "microchip,enc28j60", },
-+static const struct of_device_id enc28j60_dt_ids[] = {
-+ { .compatible = "microchip,enc28j60" },
- { /* sentinel */ }
- };
--MODULE_DEVICE_TABLE(of, enc28j60_of_match);
-+MODULE_DEVICE_TABLE(of, enc28j60_dt_ids);
-
- static struct spi_driver enc28j60_driver = {
- .driver = {
-- .name = DRV_NAME,
-- .of_match_table = enc28j60_of_match,
-+ .name = DRV_NAME,
-+ .of_match_table = enc28j60_dt_ids,
- },
- .probe = enc28j60_probe,
- .remove = enc28j60_remove,
diff --git a/target/linux/brcm2708/patches-4.4/0471-enc28j60-Fix-race-condition-in-enc28j60-driver.patch b/target/linux/brcm2708/patches-4.4/0471-enc28j60-Fix-race-condition-in-enc28j60-driver.patch
deleted file mode 100644
index 7ae5607..0000000
--- a/target/linux/brcm2708/patches-4.4/0471-enc28j60-Fix-race-condition-in-enc28j60-driver.patch
+++ /dev/null
@@ -1,64 +0,0 @@
-From 5ba5e453917fbd38b64b99af7b5a23b7ba2eb327 Mon Sep 17 00:00:00 2001
-From: Sergio Valverde <sergio.valverde at hpe.com>
-Date: Fri, 1 Jul 2016 11:44:30 -0600
-Subject: [PATCH] enc28j60: Fix race condition in enc28j60 driver
-
-(Upstream commit 373819ec391de0d11f63b10b2fb69ef2854236ca)
-
-The interrupt worker code for the enc28j60 relies only on the TXIF flag to
-determinate if the packet transmission was completed. However the datasheet
-specifies in section 12.1.3 that TXERIF will clear the TXRTS after a
-transmit abort. Also in section 12.1.4 that TXIF will be set
-when TXRTS transitions from '1' to '0'. Therefore the TXIF flag is enabled
-during transmission errors.
-
-This causes a race condition, since the worker code will invoke
-enc28j60_tx_clear() -> netif_wake_queue(), potentially invoking the
-ndo_start_xmit function to send a new packet. The enc28j60_send_packet function
-uses a workqueue that invokes enc28j60_hw_tx(). In between this function is
-called, the worker from the interrupt handler will enter the path for error
-handler because of the TXERIF flag, causing to invoke enc28j60_tx_clear() again
-and releasing the packet scheduled for transmission, causing a kernel crash with
-due a NULL pointer.
-
-These crashes due a NULL pointer were observed under stress conditions of the
-device. A BUG_ON() sequence was used to validate the issue was fixed, and has
-been running without problems for 2 years now.
-
-Signed-off-by: Diego Dompe <dompe at hpe.com>
-Acked-by: Sergio Valverde <sergio.valverde at hpe.com>
-Signed-off-by: David S. Miller <davem at davemloft.net>
----
- drivers/net/ethernet/microchip/enc28j60.c | 7 +++++--
- 1 file changed, 5 insertions(+), 2 deletions(-)
-
---- a/drivers/net/ethernet/microchip/enc28j60.c
-+++ b/drivers/net/ethernet/microchip/enc28j60.c
-@@ -1147,7 +1147,8 @@ static void enc28j60_irq_work_handler(st
- enc28j60_phy_read(priv, PHIR);
- }
- /* TX complete handler */
-- if ((intflags & EIR_TXIF) != 0) {
-+ if (((intflags & EIR_TXIF) != 0) &&
-+ ((intflags & EIR_TXERIF) == 0)) {
- bool err = false;
- loop++;
- if (netif_msg_intr(priv))
-@@ -1199,7 +1200,7 @@ static void enc28j60_irq_work_handler(st
- enc28j60_tx_clear(ndev, true);
- } else
- enc28j60_tx_clear(ndev, true);
-- locked_reg_bfclr(priv, EIR, EIR_TXERIF);
-+ locked_reg_bfclr(priv, EIR, EIR_TXERIF | EIR_TXIF);
- }
- /* RX Error handler */
- if ((intflags & EIR_RXERIF) != 0) {
-@@ -1234,6 +1235,8 @@ static void enc28j60_irq_work_handler(st
- */
- static void enc28j60_hw_tx(struct enc28j60_net *priv)
- {
-+ BUG_ON(!priv->tx_skb);
-+
- if (netif_msg_tx_queued(priv))
- printk(KERN_DEBUG DRV_NAME
- ": Tx Packet Len:%d\n", priv->tx_skb->len);
diff --git a/target/linux/brcm2708/patches-4.4/0472-Add-cm3-dts-file.patch b/target/linux/brcm2708/patches-4.4/0472-Add-cm3-dts-file.patch
deleted file mode 100644
index 0fd2fa6..0000000
--- a/target/linux/brcm2708/patches-4.4/0472-Add-cm3-dts-file.patch
+++ /dev/null
@@ -1,200 +0,0 @@
-From 7f84c992f88897b1aa0a564a29f4e9d21f7ced38 Mon Sep 17 00:00:00 2001
-From: James Adams <james at raspberrypi.org>
-Date: Fri, 12 Aug 2016 14:35:00 +0100
-Subject: [PATCH] Add cm3 dts file
-
----
- arch/arm/boot/dts/Makefile | 1 +
- arch/arm/boot/dts/bcm2710-rpi-cm3.dts | 176 ++++++++++++++++++++++++++++++++++
- 2 files changed, 177 insertions(+)
- create mode 100644 arch/arm/boot/dts/bcm2710-rpi-cm3.dts
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -6,6 +6,7 @@ dtb-$(CONFIG_ARCH_BCM2708) += bcm2708-rp
- dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-cm.dtb
- dtb-$(CONFIG_ARCH_BCM2709) += bcm2709-rpi-2-b.dtb
- dtb-$(CONFIG_ARCH_BCM2709) += bcm2710-rpi-3-b.dtb
-+dtb-$(CONFIG_ARCH_BCM2709) += bcm2710-rpi-cm3.dtb
-
- # Raspberry Pi
- ifeq ($(CONFIG_ARCH_BCM2708),y)
---- /dev/null
-+++ b/arch/arm/boot/dts/bcm2710-rpi-cm3.dts
-@@ -0,0 +1,176 @@
-+/dts-v1/;
-+
-+#include "bcm2710.dtsi"
-+
-+/ {
-+ compatible = "brcm,bcm2710","brcm,bcm2709";
-+ model = "Raspberry Pi Compute Module 3";
-+};
-+
-+&gpio {
-+
-+ mmc_pins: mmc_pins {
-+ brcm,pins = <48 49 50 51 52 53>;
-+ brcm,function = <7>; /* alt3 */
-+ brcm,pull = <0 2 2 2 2 2>;
-+ };
-+
-+ spi0_pins: spi0_pins {
-+ brcm,pins = <9 10 11>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+
-+ spi0_cs_pins: spi0_cs_pins {
-+ brcm,pins = <8 7>;
-+ brcm,function = <1>; /* output */
-+ };
-+
-+ i2c0_pins: i2c0 {
-+ brcm,pins = <0 1>;
-+ brcm,function = <4>;
-+ };
-+
-+ i2c1_pins: i2c1 {
-+ brcm,pins = <2 3>;
-+ brcm,function = <4>;
-+ };
-+
-+ i2s_pins: i2s {
-+ brcm,pins = <18 19 20 21>;
-+ brcm,function = <4>; /* alt0 */
-+ };
-+
-+ uart0_pins: uart0_pins {
-+ brcm,pins;
-+ brcm,function;
-+ brcm,pull = <0 2>;
-+ };
-+
-+ audio_pins: audio_pins {
-+ brcm,pins;
-+ brcm,function;
-+ };
-+};
-+
-+&mmc {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&mmc_pins>;
-+ non-removable;
-+ bus-width = <4>;
-+ status = "okay";
-+ brcm,overclock-50 = <0>;
-+};
-+
-+&soc {
-+ virtgpio: virtgpio {
-+ compatible = "brcm,bcm2835-virtgpio";
-+ gpio-controller;
-+ #gpio-cells = <2>;
-+ firmware = <&firmware>;
-+ status = "okay";
-+ };
-+};
-+
-+&fb {
-+ status = "okay";
-+};
-+
-+&uart0 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&uart0_pins>;
-+ status = "okay";
-+};
-+
-+&spi0 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
-+ cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
-+
-+ spidev0: spidev at 0{
-+ compatible = "spidev";
-+ reg = <0>; /* CE0 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ };
-+
-+ spidev1: spidev at 1{
-+ compatible = "spidev";
-+ reg = <1>; /* CE1 */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ spi-max-frequency = <500000>;
-+ };
-+};
-+
-+&i2c0 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2c0_pins>;
-+ clock-frequency = <100000>;
-+};
-+
-+&i2c1 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2c1_pins>;
-+ clock-frequency = <100000>;
-+};
-+
-+&i2c2 {
-+ clock-frequency = <100000>;
-+};
-+
-+&i2s {
-+ #sound-dai-cells = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2s_pins>;
-+};
-+
-+&random {
-+ status = "okay";
-+};
-+
-+&leds {
-+ act_led: act {
-+ label = "led0";
-+ linux,default-trigger = "mmc0";
-+ gpios = <&virtgpio 0 0>;
-+ };
-+};
-+
-+&hdmi {
-+ hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
-+};
-+
-+&audio {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&audio_pins>;
-+};
-+
-+/ {
-+ __overrides__ {
-+ uart0 = <&uart0>,"status";
-+ uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
-+ uart1 = <&uart1>,"status";
-+ i2s = <&i2s>,"status";
-+ spi = <&spi0>,"status";
-+ i2c0 = <&i2c0>,"status";
-+ i2c1 = <&i2c1>,"status";
-+ i2c2_iknowwhatimdoing = <&i2c2>,"status";
-+ i2c0_baudrate = <&i2c0>,"clock-frequency:0";
-+ i2c1_baudrate = <&i2c1>,"clock-frequency:0";
-+ i2c2_baudrate = <&i2c2>,"clock-frequency:0";
-+ core_freq = <&clk_core>,"clock-frequency:0";
-+
-+ act_led_gpio = <&act_led>,"gpios:4";
-+ act_led_activelow = <&act_led>,"gpios:8";
-+ act_led_trigger = <&act_led>,"linux,default-trigger";
-+
-+ audio = <&audio>,"status";
-+ watchdog = <&watchdog>,"status";
-+ random = <&random>,"status";
-+ sd_overclock = <&sdhost>,"brcm,overclock-50:0";
-+ sd_force_pio = <&sdhost>,"brcm,force-pio?";
-+ sd_pio_limit = <&sdhost>,"brcm,pio-limit:0";
-+ sd_debug = <&sdhost>,"brcm,debug";
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0473-BCM270X-Drop-HPD-setting-from-the-common-dtsi.patch b/target/linux/brcm2708/patches-4.4/0473-BCM270X-Drop-HPD-setting-from-the-common-dtsi.patch
deleted file mode 100644
index 50687cf..0000000
--- a/target/linux/brcm2708/patches-4.4/0473-BCM270X-Drop-HPD-setting-from-the-common-dtsi.patch
+++ /dev/null
@@ -1,21 +0,0 @@
-From dd354511a8542e5909ea6f3bc07a9f8fcf75ee77 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 15 Aug 2016 10:08:58 -0700
-Subject: [PATCH] BCM270X: Drop HPD setting from the common dtsi.
-
-The HPD is quite board-specific, so we need to set it in the per-board
-DT.
----
- arch/arm/boot/dts/bcm2708_common.dtsi | 1 -
- 1 file changed, 1 deletion(-)
-
---- a/arch/arm/boot/dts/bcm2708_common.dtsi
-+++ b/arch/arm/boot/dts/bcm2708_common.dtsi
-@@ -347,7 +347,6 @@
- reg = <0x7e902000 0x600>,
- <0x7e808000 0x100>;
- ddc = <&i2c2>;
-- hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
- clocks = <&cprman BCM2835_PLLH_PIX>,
- <&cprman BCM2835_CLOCK_HSM>;
- clock-names = "pixel", "hdmi";
diff --git a/target/linux/brcm2708/patches-4.4/0474-BCM2710-Drop-incorrect-HDMI-HPD-line-from-the-DT.patch b/target/linux/brcm2708/patches-4.4/0474-BCM2710-Drop-incorrect-HDMI-HPD-line-from-the-DT.patch
deleted file mode 100644
index ee3ff92..0000000
--- a/target/linux/brcm2708/patches-4.4/0474-BCM2710-Drop-incorrect-HDMI-HPD-line-from-the-DT.patch
+++ /dev/null
@@ -1,26 +0,0 @@
-From ea8d735b694f7b2100b7f2f037f7f846c0412548 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 12 Aug 2016 11:02:14 -0700
-Subject: [PATCH] BCM2710: Drop incorrect HDMI HPD line from the DT.
-
-It's actually off on the GPIO expander, which I don't think we have
-access to.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- arch/arm/boot/dts/bcm2710-rpi-3-b.dts | 4 ----
- 1 file changed, 4 deletions(-)
-
---- a/arch/arm/boot/dts/bcm2710-rpi-3-b.dts
-+++ b/arch/arm/boot/dts/bcm2710-rpi-3-b.dts
-@@ -166,10 +166,6 @@
- };
- };
-
--&hdmi {
-- hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
--};
--
- &audio {
- pinctrl-names = "default";
- pinctrl-0 = <&audio_pins>;
diff --git a/target/linux/brcm2708/patches-4.4/0475-drm-vc4-Add-a-getparam-ioctl-for-getting-the-V3D-ide.patch b/target/linux/brcm2708/patches-4.4/0475-drm-vc4-Add-a-getparam-ioctl-for-getting-the-V3D-ide.patch
deleted file mode 100644
index 2bd7dde..0000000
--- a/target/linux/brcm2708/patches-4.4/0475-drm-vc4-Add-a-getparam-ioctl-for-getting-the-V3D-ide.patch
+++ /dev/null
@@ -1,124 +0,0 @@
-From 3150988da4b514d150a5b6b5e4d7e4d5e5e47e24 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 1 Jul 2016 13:10:38 -0700
-Subject: [PATCH] drm/vc4: Add a getparam ioctl for getting the V3D identity
- regs.
-
-As I extend the driver to support different V3D revisions, userspace
-needs to know what version it's targeting. This is most easily
-detected using the V3D identity registers.
-
-v2: Make sure V3D is runtime PM on when reading the registers.
-v3: Switch to a 64-bit param value (suggested by Rob Clark in review)
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Acked-by: Daniel Vetter <daniel.vetter at ffwll.ch> (v2)
-Reviewed-by: Rob Clark <robdclark at gmail.com> (v3, over irc)
-(cherry picked from commit af713795c59fea36161a7debf97dbc10bf652cf7)
-
-v4: Squashed in "drm/vc4: Fix handling of a pm_runtime_get_sync() success case."
----
- drivers/gpu/drm/vc4/vc4_drv.c | 42 ++++++++++++++++++++++++++++++++++++++++++
- include/uapi/drm/vc4_drm.h | 12 ++++++++++++
- 2 files changed, 54 insertions(+)
-
---- a/drivers/gpu/drm/vc4/vc4_drv.c
-+++ b/drivers/gpu/drm/vc4/vc4_drv.c
-@@ -15,6 +15,7 @@
- #include <linux/module.h>
- #include <linux/of_platform.h>
- #include <linux/platform_device.h>
-+#include <linux/pm_runtime.h>
- #include "drm_fb_cma_helper.h"
-
- #include "uapi/drm/vc4_drm.h"
-@@ -64,6 +65,46 @@ void vc4_dump_regs32(const struct debugf
- }
- }
-
-+static int vc4_get_param_ioctl(struct drm_device *dev, void *data,
-+ struct drm_file *file_priv)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ struct drm_vc4_get_param *args = data;
-+ int ret;
-+
-+ if (args->pad != 0)
-+ return -EINVAL;
-+
-+ switch (args->param) {
-+ case DRM_VC4_PARAM_V3D_IDENT0:
-+ ret = pm_runtime_get_sync(&vc4->v3d->pdev->dev);
-+ if (ret < 0)
-+ return ret;
-+ args->value = V3D_READ(V3D_IDENT0);
-+ pm_runtime_put(&vc4->v3d->pdev->dev);
-+ break;
-+ case DRM_VC4_PARAM_V3D_IDENT1:
-+ ret = pm_runtime_get_sync(&vc4->v3d->pdev->dev);
-+ if (ret < 0)
-+ return ret;
-+ args->value = V3D_READ(V3D_IDENT1);
-+ pm_runtime_put(&vc4->v3d->pdev->dev);
-+ break;
-+ case DRM_VC4_PARAM_V3D_IDENT2:
-+ ret = pm_runtime_get_sync(&vc4->v3d->pdev->dev);
-+ if (ret < 0)
-+ return ret;
-+ args->value = V3D_READ(V3D_IDENT2);
-+ pm_runtime_put(&vc4->v3d->pdev->dev);
-+ break;
-+ default:
-+ DRM_DEBUG("Unknown parameter %d\n", args->param);
-+ return -EINVAL;
-+ }
-+
-+ return 0;
-+}
-+
- static void vc4_lastclose(struct drm_device *dev)
- {
- struct vc4_dev *vc4 = to_vc4_dev(dev);
-@@ -95,6 +136,7 @@ static const struct drm_ioctl_desc vc4_d
- DRM_IOCTL_DEF_DRV(VC4_CREATE_SHADER_BO, vc4_create_shader_bo_ioctl, DRM_RENDER_ALLOW),
- DRM_IOCTL_DEF_DRV(VC4_GET_HANG_STATE, vc4_get_hang_state_ioctl,
- DRM_ROOT_ONLY),
-+ DRM_IOCTL_DEF_DRV(VC4_GET_PARAM, vc4_get_param_ioctl, DRM_RENDER_ALLOW),
- };
-
- static struct drm_driver vc4_drm_driver = {
---- a/include/uapi/drm/vc4_drm.h
-+++ b/include/uapi/drm/vc4_drm.h
-@@ -37,6 +37,7 @@ extern "C" {
- #define DRM_VC4_MMAP_BO 0x04
- #define DRM_VC4_CREATE_SHADER_BO 0x05
- #define DRM_VC4_GET_HANG_STATE 0x06
-+#define DRM_VC4_GET_PARAM 0x07
-
- #define DRM_IOCTL_VC4_SUBMIT_CL DRM_IOWR(DRM_COMMAND_BASE + DRM_VC4_SUBMIT_CL, struct drm_vc4_submit_cl)
- #define DRM_IOCTL_VC4_WAIT_SEQNO DRM_IOWR(DRM_COMMAND_BASE + DRM_VC4_WAIT_SEQNO, struct drm_vc4_wait_seqno)
-@@ -45,6 +46,7 @@ extern "C" {
- #define DRM_IOCTL_VC4_MMAP_BO DRM_IOWR(DRM_COMMAND_BASE + DRM_VC4_MMAP_BO, struct drm_vc4_mmap_bo)
- #define DRM_IOCTL_VC4_CREATE_SHADER_BO DRM_IOWR(DRM_COMMAND_BASE + DRM_VC4_CREATE_SHADER_BO, struct drm_vc4_create_shader_bo)
- #define DRM_IOCTL_VC4_GET_HANG_STATE DRM_IOWR(DRM_COMMAND_BASE + DRM_VC4_GET_HANG_STATE, struct drm_vc4_get_hang_state)
-+#define DRM_IOCTL_VC4_GET_PARAM DRM_IOWR(DRM_COMMAND_BASE + DRM_VC4_GET_PARAM, struct drm_vc4_get_param)
-
- struct drm_vc4_submit_rcl_surface {
- __u32 hindex; /* Handle index, or ~0 if not present. */
-@@ -280,6 +282,16 @@ struct drm_vc4_get_hang_state {
- __u32 pad[16];
- };
-
-+#define DRM_VC4_PARAM_V3D_IDENT0 0
-+#define DRM_VC4_PARAM_V3D_IDENT1 1
-+#define DRM_VC4_PARAM_V3D_IDENT2 2
-+
-+struct drm_vc4_get_param {
-+ __u32 param;
-+ __u32 pad;
-+ __u64 value;
-+};
-+
- #if defined(__cplusplus)
- }
- #endif
diff --git a/target/linux/brcm2708/patches-4.4/0476-drm-vc4-Move-validation-s-current-max-ip-into-the-va.patch b/target/linux/brcm2708/patches-4.4/0476-drm-vc4-Move-validation-s-current-max-ip-into-the-va.patch
deleted file mode 100644
index b1928f5..0000000
--- a/target/linux/brcm2708/patches-4.4/0476-drm-vc4-Move-validation-s-current-max-ip-into-the-va.patch
+++ /dev/null
@@ -1,176 +0,0 @@
-From 84aa70ecf6b01741fda8211e050fce3f8075ea2d Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Sat, 2 Jul 2016 09:57:07 -0700
-Subject: [PATCH] drm/vc4: Move validation's current/max ip into the validation
- struct.
-
-Reduces the argument count for some of the functions, and will be used
-more with the upcoming looping support.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit d0566c2a2f2baacefe1eb75be8a001fdd6fe84a3)
----
- drivers/gpu/drm/vc4/vc4_validate_shaders.c | 54 +++++++++++++++++-------------
- 1 file changed, 30 insertions(+), 24 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_validate_shaders.c
-+++ b/drivers/gpu/drm/vc4/vc4_validate_shaders.c
-@@ -40,6 +40,14 @@
- #include "vc4_qpu_defines.h"
-
- struct vc4_shader_validation_state {
-+ /* Current IP being validated. */
-+ uint32_t ip;
-+
-+ /* IP at the end of the BO, do not read shader[max_ip] */
-+ uint32_t max_ip;
-+
-+ uint64_t *shader;
-+
- struct vc4_texture_sample_info tmu_setup[2];
- int tmu_write_count[2];
-
-@@ -129,11 +137,11 @@ record_texture_sample(struct vc4_validat
- }
-
- static bool
--check_tmu_write(uint64_t inst,
-- struct vc4_validated_shader_info *validated_shader,
-+check_tmu_write(struct vc4_validated_shader_info *validated_shader,
- struct vc4_shader_validation_state *validation_state,
- bool is_mul)
- {
-+ uint64_t inst = validation_state->shader[validation_state->ip];
- uint32_t waddr = (is_mul ?
- QPU_GET_FIELD(inst, QPU_WADDR_MUL) :
- QPU_GET_FIELD(inst, QPU_WADDR_ADD));
-@@ -228,11 +236,11 @@ check_tmu_write(uint64_t inst,
- }
-
- static bool
--check_reg_write(uint64_t inst,
-- struct vc4_validated_shader_info *validated_shader,
-+check_reg_write(struct vc4_validated_shader_info *validated_shader,
- struct vc4_shader_validation_state *validation_state,
- bool is_mul)
- {
-+ uint64_t inst = validation_state->shader[validation_state->ip];
- uint32_t waddr = (is_mul ?
- QPU_GET_FIELD(inst, QPU_WADDR_MUL) :
- QPU_GET_FIELD(inst, QPU_WADDR_ADD));
-@@ -261,7 +269,7 @@ check_reg_write(uint64_t inst,
- case QPU_W_TMU1_T:
- case QPU_W_TMU1_R:
- case QPU_W_TMU1_B:
-- return check_tmu_write(inst, validated_shader, validation_state,
-+ return check_tmu_write(validated_shader, validation_state,
- is_mul);
-
- case QPU_W_HOST_INT:
-@@ -294,10 +302,10 @@ check_reg_write(uint64_t inst,
- }
-
- static void
--track_live_clamps(uint64_t inst,
-- struct vc4_validated_shader_info *validated_shader,
-+track_live_clamps(struct vc4_validated_shader_info *validated_shader,
- struct vc4_shader_validation_state *validation_state)
- {
-+ uint64_t inst = validation_state->shader[validation_state->ip];
- uint32_t op_add = QPU_GET_FIELD(inst, QPU_OP_ADD);
- uint32_t waddr_add = QPU_GET_FIELD(inst, QPU_WADDR_ADD);
- uint32_t waddr_mul = QPU_GET_FIELD(inst, QPU_WADDR_MUL);
-@@ -369,10 +377,10 @@ track_live_clamps(uint64_t inst,
- }
-
- static bool
--check_instruction_writes(uint64_t inst,
-- struct vc4_validated_shader_info *validated_shader,
-+check_instruction_writes(struct vc4_validated_shader_info *validated_shader,
- struct vc4_shader_validation_state *validation_state)
- {
-+ uint64_t inst = validation_state->shader[validation_state->ip];
- uint32_t waddr_add = QPU_GET_FIELD(inst, QPU_WADDR_ADD);
- uint32_t waddr_mul = QPU_GET_FIELD(inst, QPU_WADDR_MUL);
- bool ok;
-@@ -382,12 +390,10 @@ check_instruction_writes(uint64_t inst,
- return false;
- }
-
-- ok = (check_reg_write(inst, validated_shader, validation_state,
-- false) &&
-- check_reg_write(inst, validated_shader, validation_state,
-- true));
-+ ok = (check_reg_write(validated_shader, validation_state, false) &&
-+ check_reg_write(validated_shader, validation_state, true));
-
-- track_live_clamps(inst, validated_shader, validation_state);
-+ track_live_clamps(validated_shader, validation_state);
-
- return ok;
- }
-@@ -417,30 +423,30 @@ vc4_validate_shader(struct drm_gem_cma_o
- {
- bool found_shader_end = false;
- int shader_end_ip = 0;
-- uint32_t ip, max_ip;
-- uint64_t *shader;
-+ uint32_t ip;
- struct vc4_validated_shader_info *validated_shader;
- struct vc4_shader_validation_state validation_state;
- int i;
-
- memset(&validation_state, 0, sizeof(validation_state));
-+ validation_state.shader = shader_obj->vaddr;
-+ validation_state.max_ip = shader_obj->base.size / sizeof(uint64_t);
-
- for (i = 0; i < 8; i++)
- validation_state.tmu_setup[i / 4].p_offset[i % 4] = ~0;
- for (i = 0; i < ARRAY_SIZE(validation_state.live_min_clamp_offsets); i++)
- validation_state.live_min_clamp_offsets[i] = ~0;
-
-- shader = shader_obj->vaddr;
-- max_ip = shader_obj->base.size / sizeof(uint64_t);
--
- validated_shader = kcalloc(1, sizeof(*validated_shader), GFP_KERNEL);
- if (!validated_shader)
- return NULL;
-
-- for (ip = 0; ip < max_ip; ip++) {
-- uint64_t inst = shader[ip];
-+ for (ip = 0; ip < validation_state.max_ip; ip++) {
-+ uint64_t inst = validation_state.shader[ip];
- uint32_t sig = QPU_GET_FIELD(inst, QPU_SIG);
-
-+ validation_state.ip = ip;
-+
- switch (sig) {
- case QPU_SIG_NONE:
- case QPU_SIG_WAIT_FOR_SCOREBOARD:
-@@ -450,7 +456,7 @@ vc4_validate_shader(struct drm_gem_cma_o
- case QPU_SIG_LOAD_TMU1:
- case QPU_SIG_PROG_END:
- case QPU_SIG_SMALL_IMM:
-- if (!check_instruction_writes(inst, validated_shader,
-+ if (!check_instruction_writes(validated_shader,
- &validation_state)) {
- DRM_ERROR("Bad write at ip %d\n", ip);
- goto fail;
-@@ -467,7 +473,7 @@ vc4_validate_shader(struct drm_gem_cma_o
- break;
-
- case QPU_SIG_LOAD_IMM:
-- if (!check_instruction_writes(inst, validated_shader,
-+ if (!check_instruction_writes(validated_shader,
- &validation_state)) {
- DRM_ERROR("Bad LOAD_IMM write at ip %d\n", ip);
- goto fail;
-@@ -487,7 +493,7 @@ vc4_validate_shader(struct drm_gem_cma_o
- break;
- }
-
-- if (ip == max_ip) {
-+ if (ip == validation_state.max_ip) {
- DRM_ERROR("shader failed to terminate before "
- "shader BO end at %zd\n",
- shader_obj->base.size);
diff --git a/target/linux/brcm2708/patches-4.4/0477-drm-vc4-Add-a-bitmap-of-branch-targets-during-shader.patch b/target/linux/brcm2708/patches-4.4/0477-drm-vc4-Add-a-bitmap-of-branch-targets-during-shader.patch
deleted file mode 100644
index 30b01a7..0000000
--- a/target/linux/brcm2708/patches-4.4/0477-drm-vc4-Add-a-bitmap-of-branch-targets-during-shader.patch
+++ /dev/null
@@ -1,200 +0,0 @@
-From f99c0e6116f2a962ee3b1af4f1bc20e36bd8fb0c Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Sat, 2 Jul 2016 10:10:24 -0700
-Subject: [PATCH] drm/vc4: Add a bitmap of branch targets during shader
- validation.
-
-This isn't used yet, it's just a first step toward loop validation.
-During the main parsing of instructions, we need to know when we hit a
-new basic block so that we can reset validated state.
-
-v2: Fix a stray semicolon after an if block. (caught by kbuild test).
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 93aa9ae3e5523e49e4e5abacd4dbee0e4ab2d931)
----
- drivers/gpu/drm/vc4/vc4_qpu_defines.h | 12 +++
- drivers/gpu/drm/vc4/vc4_validate_shaders.c | 114 ++++++++++++++++++++++++++++-
- 2 files changed, 124 insertions(+), 2 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_qpu_defines.h
-+++ b/drivers/gpu/drm/vc4/vc4_qpu_defines.h
-@@ -230,6 +230,15 @@ enum qpu_unpack_r4 {
- #define QPU_COND_MUL_SHIFT 46
- #define QPU_COND_MUL_MASK QPU_MASK(48, 46)
-
-+#define QPU_BRANCH_COND_SHIFT 52
-+#define QPU_BRANCH_COND_MASK QPU_MASK(55, 52)
-+
-+#define QPU_BRANCH_REL ((uint64_t)1 << 51)
-+#define QPU_BRANCH_REG ((uint64_t)1 << 50)
-+
-+#define QPU_BRANCH_RADDR_A_SHIFT 45
-+#define QPU_BRANCH_RADDR_A_MASK QPU_MASK(49, 45)
-+
- #define QPU_SF ((uint64_t)1 << 45)
-
- #define QPU_WADDR_ADD_SHIFT 38
-@@ -261,4 +270,7 @@ enum qpu_unpack_r4 {
- #define QPU_OP_ADD_SHIFT 24
- #define QPU_OP_ADD_MASK QPU_MASK(28, 24)
-
-+#define QPU_BRANCH_TARGET_SHIFT 0
-+#define QPU_BRANCH_TARGET_MASK QPU_MASK(31, 0)
-+
- #endif /* VC4_QPU_DEFINES_H */
---- a/drivers/gpu/drm/vc4/vc4_validate_shaders.c
-+++ b/drivers/gpu/drm/vc4/vc4_validate_shaders.c
-@@ -59,6 +59,13 @@ struct vc4_shader_validation_state {
- */
- uint32_t live_min_clamp_offsets[32 + 32 + 4];
- bool live_max_clamp_regs[32 + 32 + 4];
-+
-+ /* Bitfield of which IPs are used as branch targets.
-+ *
-+ * Used for validation that the uniform stream is updated at the right
-+ * points and clearing the texturing/clamping state.
-+ */
-+ unsigned long *branch_targets;
- };
-
- static uint32_t
-@@ -418,13 +425,104 @@ check_instruction_reads(uint64_t inst,
- return true;
- }
-
-+/* Make sure that all branches are absolute and point within the shader, and
-+ * note their targets for later.
-+ */
-+static bool
-+vc4_validate_branches(struct vc4_shader_validation_state *validation_state)
-+{
-+ uint32_t max_branch_target = 0;
-+ bool found_shader_end = false;
-+ int ip;
-+ int shader_end_ip = 0;
-+ int last_branch = -2;
-+
-+ for (ip = 0; ip < validation_state->max_ip; ip++) {
-+ uint64_t inst = validation_state->shader[ip];
-+ int32_t branch_imm = QPU_GET_FIELD(inst, QPU_BRANCH_TARGET);
-+ uint32_t sig = QPU_GET_FIELD(inst, QPU_SIG);
-+ uint32_t after_delay_ip = ip + 4;
-+ uint32_t branch_target_ip;
-+
-+ if (sig == QPU_SIG_PROG_END) {
-+ shader_end_ip = ip;
-+ found_shader_end = true;
-+ continue;
-+ }
-+
-+ if (sig != QPU_SIG_BRANCH)
-+ continue;
-+
-+ if (ip - last_branch < 4) {
-+ DRM_ERROR("Branch at %d during delay slots\n", ip);
-+ return false;
-+ }
-+ last_branch = ip;
-+
-+ if (inst & QPU_BRANCH_REG) {
-+ DRM_ERROR("branching from register relative "
-+ "not supported\n");
-+ return false;
-+ }
-+
-+ if (!(inst & QPU_BRANCH_REL)) {
-+ DRM_ERROR("relative branching required\n");
-+ return false;
-+ }
-+
-+ /* The actual branch target is the instruction after the delay
-+ * slots, plus whatever byte offset is in the low 32 bits of
-+ * the instruction. Make sure we're not branching beyond the
-+ * end of the shader object.
-+ */
-+ if (branch_imm % sizeof(inst) != 0) {
-+ DRM_ERROR("branch target not aligned\n");
-+ return false;
-+ }
-+
-+ branch_target_ip = after_delay_ip + (branch_imm >> 3);
-+ if (branch_target_ip >= validation_state->max_ip) {
-+ DRM_ERROR("Branch at %d outside of shader (ip %d/%d)\n",
-+ ip, branch_target_ip,
-+ validation_state->max_ip);
-+ return false;
-+ }
-+ set_bit(branch_target_ip, validation_state->branch_targets);
-+
-+ /* Make sure that the non-branching path is also not outside
-+ * the shader.
-+ */
-+ if (after_delay_ip >= validation_state->max_ip) {
-+ DRM_ERROR("Branch at %d continues past shader end "
-+ "(%d/%d)\n",
-+ ip, after_delay_ip, validation_state->max_ip);
-+ return false;
-+ }
-+ set_bit(after_delay_ip, validation_state->branch_targets);
-+ max_branch_target = max(max_branch_target, after_delay_ip);
-+
-+ /* There are two delay slots after program end is signaled
-+ * that are still executed, then we're finished.
-+ */
-+ if (found_shader_end && ip == shader_end_ip + 2)
-+ break;
-+ }
-+
-+ if (max_branch_target > shader_end_ip) {
-+ DRM_ERROR("Branch landed after QPU_SIG_PROG_END");
-+ return false;
-+ }
-+
-+ return true;
-+}
-+
- struct vc4_validated_shader_info *
- vc4_validate_shader(struct drm_gem_cma_object *shader_obj)
- {
- bool found_shader_end = false;
- int shader_end_ip = 0;
- uint32_t ip;
-- struct vc4_validated_shader_info *validated_shader;
-+ struct vc4_validated_shader_info *validated_shader = NULL;
- struct vc4_shader_validation_state validation_state;
- int i;
-
-@@ -437,9 +535,18 @@ vc4_validate_shader(struct drm_gem_cma_o
- for (i = 0; i < ARRAY_SIZE(validation_state.live_min_clamp_offsets); i++)
- validation_state.live_min_clamp_offsets[i] = ~0;
-
-+ validation_state.branch_targets =
-+ kcalloc(BITS_TO_LONGS(validation_state.max_ip),
-+ sizeof(unsigned long), GFP_KERNEL);
-+ if (!validation_state.branch_targets)
-+ goto fail;
-+
- validated_shader = kcalloc(1, sizeof(*validated_shader), GFP_KERNEL);
- if (!validated_shader)
-- return NULL;
-+ goto fail;
-+
-+ if (!vc4_validate_branches(&validation_state))
-+ goto fail;
-
- for (ip = 0; ip < validation_state.max_ip; ip++) {
- uint64_t inst = validation_state.shader[ip];
-@@ -508,9 +615,12 @@ vc4_validate_shader(struct drm_gem_cma_o
- (validated_shader->uniforms_size +
- 4 * validated_shader->num_texture_samples);
-
-+ kfree(validation_state.branch_targets);
-+
- return validated_shader;
-
- fail:
-+ kfree(validation_state.branch_targets);
- if (validated_shader) {
- kfree(validated_shader->texture_samples);
- kfree(validated_shader);
diff --git a/target/linux/brcm2708/patches-4.4/0478-drm-vc4-Add-support-for-branching-in-shader-validati.patch b/target/linux/brcm2708/patches-4.4/0478-drm-vc4-Add-support-for-branching-in-shader-validati.patch
deleted file mode 100644
index 69c11e9..0000000
--- a/target/linux/brcm2708/patches-4.4/0478-drm-vc4-Add-support-for-branching-in-shader-validati.patch
+++ /dev/null
@@ -1,475 +0,0 @@
-From 023a75ed42f697c00eede44a800eedd5beb1ff34 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Sat, 2 Jul 2016 12:17:10 -0700
-Subject: [PATCH] drm/vc4: Add support for branching in shader validation.
-
-We're already checking that branch instructions are between the start
-of the shader and the proper PROG_END sequence. The other thing we
-need to make branching safe is to verify that the shader doesn't read
-past the end of the uniforms stream.
-
-To do that, we require that at any basic block reading uniforms have
-the following instructions:
-
-load_imm temp, <next offset within uniform stream>
-add unif_addr, temp, unif
-
-The instructions are generated by userspace, and the kernel verifies
-that the load_imm is of the expected offset, and that the add adds it
-to a uniform. We track which uniform in the stream that is, and at
-draw call time fix up the uniform stream to have the address of the
-start of the shader's uniforms at that location.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 6d45c81d229d71da54d374143e7d6abad4c0cf31)
----
- drivers/gpu/drm/vc4/vc4_drv.h | 3 +
- drivers/gpu/drm/vc4/vc4_qpu_defines.h | 3 +
- drivers/gpu/drm/vc4/vc4_validate.c | 13 +-
- drivers/gpu/drm/vc4/vc4_validate_shaders.c | 281 +++++++++++++++++++++++++++--
- 4 files changed, 283 insertions(+), 17 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_drv.h
-+++ b/drivers/gpu/drm/vc4/vc4_drv.h
-@@ -363,6 +363,9 @@ struct vc4_validated_shader_info {
- uint32_t uniforms_src_size;
- uint32_t num_texture_samples;
- struct vc4_texture_sample_info *texture_samples;
-+
-+ uint32_t num_uniform_addr_offsets;
-+ uint32_t *uniform_addr_offsets;
- };
-
- /**
---- a/drivers/gpu/drm/vc4/vc4_qpu_defines.h
-+++ b/drivers/gpu/drm/vc4/vc4_qpu_defines.h
-@@ -270,6 +270,9 @@ enum qpu_unpack_r4 {
- #define QPU_OP_ADD_SHIFT 24
- #define QPU_OP_ADD_MASK QPU_MASK(28, 24)
-
-+#define QPU_LOAD_IMM_SHIFT 0
-+#define QPU_LOAD_IMM_MASK QPU_MASK(31, 0)
-+
- #define QPU_BRANCH_TARGET_SHIFT 0
- #define QPU_BRANCH_TARGET_MASK QPU_MASK(31, 0)
-
---- a/drivers/gpu/drm/vc4/vc4_validate.c
-+++ b/drivers/gpu/drm/vc4/vc4_validate.c
-@@ -802,7 +802,7 @@ validate_gl_shader_rec(struct drm_device
- uint32_t src_offset = *(uint32_t *)(pkt_u + o);
- uint32_t *texture_handles_u;
- void *uniform_data_u;
-- uint32_t tex;
-+ uint32_t tex, uni;
-
- *(uint32_t *)(pkt_v + o) = bo[i]->paddr + src_offset;
-
-@@ -840,6 +840,17 @@ validate_gl_shader_rec(struct drm_device
- }
- }
-
-+ /* Fill in the uniform slots that need this shader's
-+ * start-of-uniforms address (used for resetting the uniform
-+ * stream in the presence of control flow).
-+ */
-+ for (uni = 0;
-+ uni < validated_shader->num_uniform_addr_offsets;
-+ uni++) {
-+ uint32_t o = validated_shader->uniform_addr_offsets[uni];
-+ ((uint32_t *)exec->uniforms_v)[o] = exec->uniforms_p;
-+ }
-+
- *(uint32_t *)(pkt_v + o + 4) = exec->uniforms_p;
-
- exec->uniforms_u += validated_shader->uniforms_src_size;
---- a/drivers/gpu/drm/vc4/vc4_validate_shaders.c
-+++ b/drivers/gpu/drm/vc4/vc4_validate_shaders.c
-@@ -39,6 +39,8 @@
- #include "vc4_drv.h"
- #include "vc4_qpu_defines.h"
-
-+#define LIVE_REG_COUNT (32 + 32 + 4)
-+
- struct vc4_shader_validation_state {
- /* Current IP being validated. */
- uint32_t ip;
-@@ -57,8 +59,9 @@ struct vc4_shader_validation_state {
- *
- * This is used for the validation of direct address memory reads.
- */
-- uint32_t live_min_clamp_offsets[32 + 32 + 4];
-- bool live_max_clamp_regs[32 + 32 + 4];
-+ uint32_t live_min_clamp_offsets[LIVE_REG_COUNT];
-+ bool live_max_clamp_regs[LIVE_REG_COUNT];
-+ uint32_t live_immediates[LIVE_REG_COUNT];
-
- /* Bitfield of which IPs are used as branch targets.
- *
-@@ -66,6 +69,20 @@ struct vc4_shader_validation_state {
- * points and clearing the texturing/clamping state.
- */
- unsigned long *branch_targets;
-+
-+ /* Set when entering a basic block, and cleared when the uniform
-+ * address update is found. This is used to make sure that we don't
-+ * read uniforms when the address is undefined.
-+ */
-+ bool needs_uniform_address_update;
-+
-+ /* Set when we find a backwards branch. If the branch is backwards,
-+ * the taraget is probably doing an address reset to read uniforms,
-+ * and so we need to be sure that a uniforms address is present in the
-+ * stream, even if the shader didn't need to read uniforms in later
-+ * basic blocks.
-+ */
-+ bool needs_uniform_address_for_loop;
- };
-
- static uint32_t
-@@ -227,8 +244,14 @@ check_tmu_write(struct vc4_validated_sha
- /* Since direct uses a RADDR uniform reference, it will get counted in
- * check_instruction_reads()
- */
-- if (!is_direct)
-+ if (!is_direct) {
-+ if (validation_state->needs_uniform_address_update) {
-+ DRM_ERROR("Texturing with undefined uniform address\n");
-+ return false;
-+ }
-+
- validated_shader->uniforms_size += 4;
-+ }
-
- if (submit) {
- if (!record_texture_sample(validated_shader,
-@@ -242,6 +265,98 @@ check_tmu_write(struct vc4_validated_sha
- return true;
- }
-
-+static bool require_uniform_address_uniform(struct vc4_validated_shader_info *validated_shader)
-+{
-+ uint32_t o = validated_shader->num_uniform_addr_offsets;
-+ uint32_t num_uniforms = validated_shader->uniforms_size / 4;
-+
-+ validated_shader->uniform_addr_offsets =
-+ krealloc(validated_shader->uniform_addr_offsets,
-+ (o + 1) *
-+ sizeof(*validated_shader->uniform_addr_offsets),
-+ GFP_KERNEL);
-+ if (!validated_shader->uniform_addr_offsets)
-+ return false;
-+
-+ validated_shader->uniform_addr_offsets[o] = num_uniforms;
-+ validated_shader->num_uniform_addr_offsets++;
-+
-+ return true;
-+}
-+
-+static bool
-+validate_uniform_address_write(struct vc4_validated_shader_info *validated_shader,
-+ struct vc4_shader_validation_state *validation_state,
-+ bool is_mul)
-+{
-+ uint64_t inst = validation_state->shader[validation_state->ip];
-+ u32 add_b = QPU_GET_FIELD(inst, QPU_ADD_B);
-+ u32 raddr_a = QPU_GET_FIELD(inst, QPU_RADDR_A);
-+ u32 raddr_b = QPU_GET_FIELD(inst, QPU_RADDR_B);
-+ u32 add_lri = raddr_add_a_to_live_reg_index(inst);
-+ /* We want our reset to be pointing at whatever uniform follows the
-+ * uniforms base address.
-+ */
-+ u32 expected_offset = validated_shader->uniforms_size + 4;
-+
-+ /* We only support absolute uniform address changes, and we
-+ * require that they be in the current basic block before any
-+ * of its uniform reads.
-+ *
-+ * One could potentially emit more efficient QPU code, by
-+ * noticing that (say) an if statement does uniform control
-+ * flow for all threads and that the if reads the same number
-+ * of uniforms on each side. However, this scheme is easy to
-+ * validate so it's all we allow for now.
-+ */
-+
-+ if (QPU_GET_FIELD(inst, QPU_SIG) != QPU_SIG_NONE) {
-+ DRM_ERROR("uniforms address change must be "
-+ "normal math\n");
-+ return false;
-+ }
-+
-+ if (is_mul || QPU_GET_FIELD(inst, QPU_OP_ADD) != QPU_A_ADD) {
-+ DRM_ERROR("Uniform address reset must be an ADD.\n");
-+ return false;
-+ }
-+
-+ if (QPU_GET_FIELD(inst, QPU_COND_ADD) != QPU_COND_ALWAYS) {
-+ DRM_ERROR("Uniform address reset must be unconditional.\n");
-+ return false;
-+ }
-+
-+ if (QPU_GET_FIELD(inst, QPU_PACK) != QPU_PACK_A_NOP &&
-+ !(inst & QPU_PM)) {
-+ DRM_ERROR("No packing allowed on uniforms reset\n");
-+ return false;
-+ }
-+
-+ if (add_lri == -1) {
-+ DRM_ERROR("First argument of uniform address write must be "
-+ "an immediate value.\n");
-+ return false;
-+ }
-+
-+ if (validation_state->live_immediates[add_lri] != expected_offset) {
-+ DRM_ERROR("Resetting uniforms with offset %db instead of %db\n",
-+ validation_state->live_immediates[add_lri],
-+ expected_offset);
-+ return false;
-+ }
-+
-+ if (!(add_b == QPU_MUX_A && raddr_a == QPU_R_UNIF) &&
-+ !(add_b == QPU_MUX_B && raddr_b == QPU_R_UNIF)) {
-+ DRM_ERROR("Second argument of uniform address write must be "
-+ "a uniform.\n");
-+ return false;
-+ }
-+
-+ validation_state->needs_uniform_address_update = false;
-+ validation_state->needs_uniform_address_for_loop = false;
-+ return require_uniform_address_uniform(validated_shader);
-+}
-+
- static bool
- check_reg_write(struct vc4_validated_shader_info *validated_shader,
- struct vc4_shader_validation_state *validation_state,
-@@ -251,14 +366,37 @@ check_reg_write(struct vc4_validated_sha
- uint32_t waddr = (is_mul ?
- QPU_GET_FIELD(inst, QPU_WADDR_MUL) :
- QPU_GET_FIELD(inst, QPU_WADDR_ADD));
-+ uint32_t sig = QPU_GET_FIELD(inst, QPU_SIG);
-+ bool ws = inst & QPU_WS;
-+ bool is_b = is_mul ^ ws;
-+ u32 lri = waddr_to_live_reg_index(waddr, is_b);
-+
-+ if (lri != -1) {
-+ uint32_t cond_add = QPU_GET_FIELD(inst, QPU_COND_ADD);
-+ uint32_t cond_mul = QPU_GET_FIELD(inst, QPU_COND_MUL);
-+
-+ if (sig == QPU_SIG_LOAD_IMM &&
-+ QPU_GET_FIELD(inst, QPU_PACK) == QPU_PACK_A_NOP &&
-+ ((is_mul && cond_mul == QPU_COND_ALWAYS) ||
-+ (!is_mul && cond_add == QPU_COND_ALWAYS))) {
-+ validation_state->live_immediates[lri] =
-+ QPU_GET_FIELD(inst, QPU_LOAD_IMM);
-+ } else {
-+ validation_state->live_immediates[lri] = ~0;
-+ }
-+ }
-
- switch (waddr) {
- case QPU_W_UNIFORMS_ADDRESS:
-- /* XXX: We'll probably need to support this for reladdr, but
-- * it's definitely a security-related one.
-- */
-- DRM_ERROR("uniforms address load unsupported\n");
-- return false;
-+ if (is_b) {
-+ DRM_ERROR("relative uniforms address change "
-+ "unsupported\n");
-+ return false;
-+ }
-+
-+ return validate_uniform_address_write(validated_shader,
-+ validation_state,
-+ is_mul);
-
- case QPU_W_TLB_COLOR_MS:
- case QPU_W_TLB_COLOR_ALL:
-@@ -406,9 +544,35 @@ check_instruction_writes(struct vc4_vali
- }
-
- static bool
--check_instruction_reads(uint64_t inst,
-- struct vc4_validated_shader_info *validated_shader)
-+check_branch(uint64_t inst,
-+ struct vc4_validated_shader_info *validated_shader,
-+ struct vc4_shader_validation_state *validation_state,
-+ int ip)
- {
-+ int32_t branch_imm = QPU_GET_FIELD(inst, QPU_BRANCH_TARGET);
-+ uint32_t waddr_add = QPU_GET_FIELD(inst, QPU_WADDR_ADD);
-+ uint32_t waddr_mul = QPU_GET_FIELD(inst, QPU_WADDR_MUL);
-+
-+ if ((int)branch_imm < 0)
-+ validation_state->needs_uniform_address_for_loop = true;
-+
-+ /* We don't want to have to worry about validation of this, and
-+ * there's no need for it.
-+ */
-+ if (waddr_add != QPU_W_NOP || waddr_mul != QPU_W_NOP) {
-+ DRM_ERROR("branch instruction at %d wrote a register.\n",
-+ validation_state->ip);
-+ return false;
-+ }
-+
-+ return true;
-+}
-+
-+static bool
-+check_instruction_reads(struct vc4_validated_shader_info *validated_shader,
-+ struct vc4_shader_validation_state *validation_state)
-+{
-+ uint64_t inst = validation_state->shader[validation_state->ip];
- uint32_t raddr_a = QPU_GET_FIELD(inst, QPU_RADDR_A);
- uint32_t raddr_b = QPU_GET_FIELD(inst, QPU_RADDR_B);
- uint32_t sig = QPU_GET_FIELD(inst, QPU_SIG);
-@@ -420,6 +584,12 @@ check_instruction_reads(uint64_t inst,
- * already be OOM.
- */
- validated_shader->uniforms_size += 4;
-+
-+ if (validation_state->needs_uniform_address_update) {
-+ DRM_ERROR("Uniform read with undefined uniform "
-+ "address\n");
-+ return false;
-+ }
- }
-
- return true;
-@@ -516,6 +686,65 @@ vc4_validate_branches(struct vc4_shader_
- return true;
- }
-
-+/* Resets any known state for the shader, used when we may be branched to from
-+ * multiple locations in the program (or at shader start).
-+ */
-+static void
-+reset_validation_state(struct vc4_shader_validation_state *validation_state)
-+{
-+ int i;
-+
-+ for (i = 0; i < 8; i++)
-+ validation_state->tmu_setup[i / 4].p_offset[i % 4] = ~0;
-+
-+ for (i = 0; i < LIVE_REG_COUNT; i++) {
-+ validation_state->live_min_clamp_offsets[i] = ~0;
-+ validation_state->live_max_clamp_regs[i] = false;
-+ validation_state->live_immediates[i] = ~0;
-+ }
-+}
-+
-+static bool
-+texturing_in_progress(struct vc4_shader_validation_state *validation_state)
-+{
-+ return (validation_state->tmu_write_count[0] != 0 ||
-+ validation_state->tmu_write_count[1] != 0);
-+}
-+
-+static bool
-+vc4_handle_branch_target(struct vc4_shader_validation_state *validation_state)
-+{
-+ uint32_t ip = validation_state->ip;
-+
-+ if (!test_bit(ip, validation_state->branch_targets))
-+ return true;
-+
-+ if (texturing_in_progress(validation_state)) {
-+ DRM_ERROR("Branch target landed during TMU setup\n");
-+ return false;
-+ }
-+
-+ /* Reset our live values tracking, since this instruction may have
-+ * multiple predecessors.
-+ *
-+ * One could potentially do analysis to determine that, for
-+ * example, all predecessors have a live max clamp in the same
-+ * register, but we don't bother with that.
-+ */
-+ reset_validation_state(validation_state);
-+
-+ /* Since we've entered a basic block from potentially multiple
-+ * predecessors, we need the uniforms address to be updated before any
-+ * unforms are read. We require that after any branch point, the next
-+ * uniform to be loaded is a uniform address offset. That uniform's
-+ * offset will be marked by the uniform address register write
-+ * validation, or a one-off the end-of-program check.
-+ */
-+ validation_state->needs_uniform_address_update = true;
-+
-+ return true;
-+}
-+
- struct vc4_validated_shader_info *
- vc4_validate_shader(struct drm_gem_cma_object *shader_obj)
- {
-@@ -524,16 +753,12 @@ vc4_validate_shader(struct drm_gem_cma_o
- uint32_t ip;
- struct vc4_validated_shader_info *validated_shader = NULL;
- struct vc4_shader_validation_state validation_state;
-- int i;
-
- memset(&validation_state, 0, sizeof(validation_state));
- validation_state.shader = shader_obj->vaddr;
- validation_state.max_ip = shader_obj->base.size / sizeof(uint64_t);
-
-- for (i = 0; i < 8; i++)
-- validation_state.tmu_setup[i / 4].p_offset[i % 4] = ~0;
-- for (i = 0; i < ARRAY_SIZE(validation_state.live_min_clamp_offsets); i++)
-- validation_state.live_min_clamp_offsets[i] = ~0;
-+ reset_validation_state(&validation_state);
-
- validation_state.branch_targets =
- kcalloc(BITS_TO_LONGS(validation_state.max_ip),
-@@ -554,6 +779,9 @@ vc4_validate_shader(struct drm_gem_cma_o
-
- validation_state.ip = ip;
-
-+ if (!vc4_handle_branch_target(&validation_state))
-+ goto fail;
-+
- switch (sig) {
- case QPU_SIG_NONE:
- case QPU_SIG_WAIT_FOR_SCOREBOARD:
-@@ -569,7 +797,8 @@ vc4_validate_shader(struct drm_gem_cma_o
- goto fail;
- }
-
-- if (!check_instruction_reads(inst, validated_shader))
-+ if (!check_instruction_reads(validated_shader,
-+ &validation_state))
- goto fail;
-
- if (sig == QPU_SIG_PROG_END) {
-@@ -587,6 +816,11 @@ vc4_validate_shader(struct drm_gem_cma_o
- }
- break;
-
-+ case QPU_SIG_BRANCH:
-+ if (!check_branch(inst, validated_shader,
-+ &validation_state, ip))
-+ goto fail;
-+ break;
- default:
- DRM_ERROR("Unsupported QPU signal %d at "
- "instruction %d\n", sig, ip);
-@@ -607,6 +841,21 @@ vc4_validate_shader(struct drm_gem_cma_o
- goto fail;
- }
-
-+ /* If we did a backwards branch and we haven't emitted a uniforms
-+ * reset since then, we still need the uniforms stream to have the
-+ * uniforms address available so that the backwards branch can do its
-+ * uniforms reset.
-+ *
-+ * We could potentially prove that the backwards branch doesn't
-+ * contain any uses of uniforms until program exit, but that doesn't
-+ * seem to be worth the trouble.
-+ */
-+ if (validation_state.needs_uniform_address_for_loop) {
-+ if (!require_uniform_address_uniform(validated_shader))
-+ goto fail;
-+ validated_shader->uniforms_size += 4;
-+ }
-+
- /* Again, no chance of integer overflow here because the worst case
- * scenario is 8 bytes of uniforms plus handles per 8-byte
- * instruction.
diff --git a/target/linux/brcm2708/patches-4.4/0479-drm-vc4-Add-a-getparam-to-signal-support-for-branche.patch b/target/linux/brcm2708/patches-4.4/0479-drm-vc4-Add-a-getparam-to-signal-support-for-branche.patch
deleted file mode 100644
index aa3e8c8..0000000
--- a/target/linux/brcm2708/patches-4.4/0479-drm-vc4-Add-a-getparam-to-signal-support-for-branche.patch
+++ /dev/null
@@ -1,38 +0,0 @@
-From 853b4e237d464fff62263aa19ed00786475fbabc Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Sat, 2 Jul 2016 14:14:27 -0700
-Subject: [PATCH] drm/vc4: Add a getparam to signal support for branches.
-
-Userspace needs to know if it can create shaders that do branching.
-Otherwise, for backwards compatibility with old kernels it needs to
-lower if statements to conditional assignments.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 7363cee5b467c31dc3af2ac98df0634bb8bbc668)
----
- drivers/gpu/drm/vc4/vc4_drv.c | 3 +++
- include/uapi/drm/vc4_drm.h | 1 +
- 2 files changed, 4 insertions(+)
-
---- a/drivers/gpu/drm/vc4/vc4_drv.c
-+++ b/drivers/gpu/drm/vc4/vc4_drv.c
-@@ -97,6 +97,9 @@ static int vc4_get_param_ioctl(struct dr
- args->value = V3D_READ(V3D_IDENT2);
- pm_runtime_put(&vc4->v3d->pdev->dev);
- break;
-+ case DRM_VC4_PARAM_SUPPORTS_BRANCHES:
-+ args->value = true;
-+ break;
- default:
- DRM_DEBUG("Unknown parameter %d\n", args->param);
- return -EINVAL;
---- a/include/uapi/drm/vc4_drm.h
-+++ b/include/uapi/drm/vc4_drm.h
-@@ -285,6 +285,7 @@ struct drm_vc4_get_hang_state {
- #define DRM_VC4_PARAM_V3D_IDENT0 0
- #define DRM_VC4_PARAM_V3D_IDENT1 1
- #define DRM_VC4_PARAM_V3D_IDENT2 2
-+#define DRM_VC4_PARAM_SUPPORTS_BRANCHES 3
-
- struct drm_vc4_get_param {
- __u32 param;
diff --git a/target/linux/brcm2708/patches-4.4/0480-drm-vc4-Don-t-force-new-binner-overflow-allocation-p.patch b/target/linux/brcm2708/patches-4.4/0480-drm-vc4-Don-t-force-new-binner-overflow-allocation-p.patch
deleted file mode 100644
index c737d46..0000000
--- a/target/linux/brcm2708/patches-4.4/0480-drm-vc4-Don-t-force-new-binner-overflow-allocation-p.patch
+++ /dev/null
@@ -1,28 +0,0 @@
-From 620d4d361a3bddf920e1f816de517a822726a80b Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 2 Aug 2016 17:17:52 -0700
-Subject: [PATCH] drm/vc4: Don't force new binner overflow allocation per draw.
-
-This came from the initial bringup code, which always idled the GPU
-and always reset the overflow. That massively increases the size of
-the working set when you're doing lots of small draws, though, as is
-common on X desktops or piglit.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_gem.c | 4 ----
- 1 file changed, 4 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -435,10 +435,6 @@ again:
-
- vc4_flush_caches(dev);
-
-- /* Disable the binner's pre-loaded overflow memory address */
-- V3D_WRITE(V3D_BPOA, 0);
-- V3D_WRITE(V3D_BPOS, 0);
--
- /* Either put the job in the binner if it uses the binner, or
- * immediately move it to the to-be-rendered queue.
- */
diff --git a/target/linux/brcm2708/patches-4.4/0481-drm-vc4-Use-drm_free_large-on-handles-to-match-its-a.patch b/target/linux/brcm2708/patches-4.4/0481-drm-vc4-Use-drm_free_large-on-handles-to-match-its-a.patch
deleted file mode 100644
index 776de7f..0000000
--- a/target/linux/brcm2708/patches-4.4/0481-drm-vc4-Use-drm_free_large-on-handles-to-match-its-a.patch
+++ /dev/null
@@ -1,27 +0,0 @@
-From e30f06162959e0e0cc61b9c6f1c0d56bef7666d2 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 19 Jul 2016 11:31:19 -0700
-Subject: [PATCH] drm/vc4: Use drm_free_large() on handles to match its
- allocation.
-
-If you managed to exceed the limit to switch to vmalloc, we'd use the
-wrong free.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Fixes: d5b1a78a772f ("drm/vc4: Add support for drawing 3D frames.")
-Cc: stable at vger.kernel.org
----
- drivers/gpu/drm/vc4/vc4_gem.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -584,7 +584,7 @@ vc4_cl_lookup_bos(struct drm_device *dev
- spin_unlock(&file_priv->table_lock);
-
- fail:
-- kfree(handles);
-+ drm_free_large(handles);
- return 0;
- }
-
diff --git a/target/linux/brcm2708/patches-4.4/0482-drm-vc4-Fix-oops-when-userspace-hands-in-a-bad-BO.patch b/target/linux/brcm2708/patches-4.4/0482-drm-vc4-Fix-oops-when-userspace-hands-in-a-bad-BO.patch
deleted file mode 100644
index d1b4665..0000000
--- a/target/linux/brcm2708/patches-4.4/0482-drm-vc4-Fix-oops-when-userspace-hands-in-a-bad-BO.patch
+++ /dev/null
@@ -1,26 +0,0 @@
-From 77fe7797b274d208fcb4ced899dba8991813827c Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 25 Jul 2016 16:10:04 -0700
-Subject: [PATCH] drm/vc4: Fix oops when userspace hands in a bad BO.
-
-We'd end up NULL pointer dereferencing because we didn't take the
-error path out in the parent. Fixes igt vc4_lookup_fail test.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Fixes: d5b1a78a772f ("drm/vc4: Add support for drawing 3D frames.")
-Cc: stable at vger.kernel.org
----
- drivers/gpu/drm/vc4/vc4_gem.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -585,7 +585,7 @@ vc4_cl_lookup_bos(struct drm_device *dev
-
- fail:
- drm_free_large(handles);
-- return 0;
-+ return ret;
- }
-
- static int
diff --git a/target/linux/brcm2708/patches-4.4/0483-drm-vc4-Fix-overflow-mem-unreferencing-when-the-binn.patch b/target/linux/brcm2708/patches-4.4/0483-drm-vc4-Fix-overflow-mem-unreferencing-when-the-binn.patch
deleted file mode 100644
index fe0574a..0000000
--- a/target/linux/brcm2708/patches-4.4/0483-drm-vc4-Fix-overflow-mem-unreferencing-when-the-binn.patch
+++ /dev/null
@@ -1,57 +0,0 @@
-From a2f60ab34906ce29882cab71b1fcf81308a11009 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Thu, 21 Jul 2016 13:39:11 -0700
-Subject: [PATCH] drm/vc4: Fix overflow mem unreferencing when the binner runs
- dry.
-
-Overflow memory handling is tricky: While it's still referenced by the
-BPO registers, we want to keep it from being freed. When we are
-putting a new set of overflow memory in the registers, we need to
-assign the old one to the last rendering job using it.
-
-We were looking at "what's currently running in the binner", but since
-the bin/render submission split, we may end up with the binner
-completing and having no new job while the renderer is still
-processing. So, if we don't find a bin job at all, look at the
-highest-seqno (last) render job to attach our overflow to.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Fixes: ca26d28bbaa3 ("drm/vc4: improve throughput by pipelining binning and rendering jobs")
-Cc: stable at vger.kernel.org
----
- drivers/gpu/drm/vc4/vc4_drv.h | 9 +++++++++
- drivers/gpu/drm/vc4/vc4_irq.c | 4 +++-
- 2 files changed, 12 insertions(+), 1 deletion(-)
-
---- a/drivers/gpu/drm/vc4/vc4_drv.h
-+++ b/drivers/gpu/drm/vc4/vc4_drv.h
-@@ -329,6 +329,15 @@ vc4_first_render_job(struct vc4_dev *vc4
- struct vc4_exec_info, head);
- }
-
-+static inline struct vc4_exec_info *
-+vc4_last_render_job(struct vc4_dev *vc4)
-+{
-+ if (list_empty(&vc4->render_job_list))
-+ return NULL;
-+ return list_last_entry(&vc4->render_job_list,
-+ struct vc4_exec_info, head);
-+}
-+
- /**
- * struct vc4_texture_sample_info - saves the offsets into the UBO for texture
- * setup parameters.
---- a/drivers/gpu/drm/vc4/vc4_irq.c
-+++ b/drivers/gpu/drm/vc4/vc4_irq.c
-@@ -83,8 +83,10 @@ vc4_overflow_mem_work(struct work_struct
-
- spin_lock_irqsave(&vc4->job_lock, irqflags);
- current_exec = vc4_first_bin_job(vc4);
-+ if (!current_exec)
-+ current_exec = vc4_last_render_job(vc4);
- if (current_exec) {
-- vc4->overflow_mem->seqno = vc4->finished_seqno + 1;
-+ vc4->overflow_mem->seqno = current_exec->seqno;
- list_add_tail(&vc4->overflow_mem->unref_head,
- ¤t_exec->unref_list);
- vc4->overflow_mem = NULL;
diff --git a/target/linux/brcm2708/patches-4.4/0484-config-Enable-SERIAL_SC16IS7XX_SPI.patch b/target/linux/brcm2708/patches-4.4/0484-config-Enable-SERIAL_SC16IS7XX_SPI.patch
deleted file mode 100644
index 4b7c416..0000000
--- a/target/linux/brcm2708/patches-4.4/0484-config-Enable-SERIAL_SC16IS7XX_SPI.patch
+++ /dev/null
@@ -1,33 +0,0 @@
-From 03014a6c1ff83b3aba219dd709254c71be94f8eb Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Thu, 18 Aug 2016 17:36:39 +0100
-Subject: [PATCH] config: Enable SERIAL_SC16IS7XX_SPI
-
-Previously only the I2C mode was supported.
-
-See: https://github.com/raspberrypi/linux/issues/1594
----
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 2 files changed, 2 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -601,6 +601,7 @@ CONFIG_SERIAL_AMBA_PL011=y
- CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
- CONFIG_SERIAL_OF_PLATFORM=y
- CONFIG_SERIAL_SC16IS7XX=m
-+CONFIG_SERIAL_SC16IS7XX_SPI=y
- CONFIG_TTY_PRINTK=y
- CONFIG_HW_RANDOM=y
- CONFIG_RAW_DRIVER=y
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -594,6 +594,7 @@ CONFIG_SERIAL_AMBA_PL011=y
- CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
- CONFIG_SERIAL_OF_PLATFORM=y
- CONFIG_SERIAL_SC16IS7XX=m
-+CONFIG_SERIAL_SC16IS7XX_SPI=y
- CONFIG_TTY_PRINTK=y
- CONFIG_HW_RANDOM=y
- CONFIG_RAW_DRIVER=y
diff --git a/target/linux/brcm2708/patches-4.4/0485-Overlay-for-Microchip-MCP23S08-17-SPI-gpio-expanders.patch b/target/linux/brcm2708/patches-4.4/0485-Overlay-for-Microchip-MCP23S08-17-SPI-gpio-expanders.patch
deleted file mode 100644
index d94d615..0000000
--- a/target/linux/brcm2708/patches-4.4/0485-Overlay-for-Microchip-MCP23S08-17-SPI-gpio-expanders.patch
+++ /dev/null
@@ -1,791 +0,0 @@
-From 7312a1a17fcfd2ae587be671f895b23c8973e9ad Mon Sep 17 00:00:00 2001
-From: wavelet2 <a3d35232 at btinternet.com>
-Date: Fri, 19 Aug 2016 09:32:53 +0100
-Subject: [PATCH] Overlay for Microchip MCP23S08/17 SPI gpio expanders (#1566)
-
-Added Overlay for Microchip MCP23S08/17 SPI gpio expanders
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 24 +
- arch/arm/boot/dts/overlays/mcp23s17-overlay.dts | 732 ++++++++++++++++++++++++
- 3 files changed, 757 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/mcp23s17-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -49,6 +49,7 @@ dtbo-$(RPI_DT_OVERLAYS) += justboom-dac.
- dtbo-$(RPI_DT_OVERLAYS) += justboom-digi.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += lirc-rpi.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += mcp23017.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += mcp23s17.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += mcp2515-can0.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += mcp2515-can1.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += mmc.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -628,6 +628,30 @@ Params: gpiopin Gpio pin
- addr I2C address of the MCP23017 (default: 0x20)
-
-
-+Name: mcp23s17
-+Info: Configures the MCP23S08/17 SPI GPIO expanders.
-+ If devices are present on SPI1 or SPI2, those interfaces must be enabled
-+ with one of the spi1-1/2/3cs and/or spi2-1/2/3cs overlays.
-+ If interrupts are enabled for a device on a given CS# on a SPI bus, that
-+ device must be the only one present on that SPI bus/CS#.
-+Load: dtoverlay=mcp23s17,<param>=<val>
-+Params: s08-spi<n>-<m>-present 4-bit integer, bitmap indicating MCP23S08
-+ devices present on SPI<n>, CS#<m>
-+
-+ s17-spi<n>-<m>-present 8-bit integer, bitmap indicating MCP23S17
-+ devices present on SPI<n>, CS#<m>
-+
-+ s08-spi<n>-<m>-int-gpio integer, enables interrupts on a single
-+ MCP23S08 device on SPI<n>, CS#<m>, specifies
-+ the GPIO pin to which INT output of MCP23S08
-+ is connected.
-+
-+ s17-spi<n>-<m>-int-gpio integer, enables mirrored interrupts on a
-+ single MCP23S17 device on SPI<n>, CS#<m>,
-+ specifies the GPIO pin to which either INTA
-+ or INTB output of MCP23S17 is connected.
-+
-+
- Name: mcp2515-can0
- Info: Configures the MCP2515 CAN controller on spi0.0
- Load: dtoverlay=mcp2515-can0,<param>=<val>
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/mcp23s17-overlay.dts
-@@ -0,0 +1,732 @@
-+// Overlay for MCP23S08/17 GPIO Extenders from Microchip Semiconductor
-+
-+// dtparams:
-+// s08-spi<n>-<m>-present - 4-bit integer, bitmap indicating MCP23S08 devices present on SPI<n>, CS#<m>.
-+// s17-spi<n>-<m>-present - 8-bit integer, bitmap indicating MCP23S17 devices present on SPI<n>, CS#<m>.
-+// s08-spi<n>-<m>-int-gpio - integer, enables interrupts on a single MCP23S08 device on SPI<n>, CS#<m>, specifies the GPIO pin to which INT output is connected.
-+// s17-spi<n>-<m>-int-gpio - integer, enables mirrored interrupts on a single MCP23S17 device on SPI<n>, CS#<m>, specifies the GPIO pin to which either INTA or INTB output is connected.
-+//
-+// If devices are present on SPI1 or SPI2, those interfaces must be enabled with one of the spi1-1/2/3cs and/or spi2-1/2/3cs overlays.
-+// If interrupts are enabled for a device on a given CS# on a SPI bus, that device must be the only one present on that SPI bus/CS#.
-+//
-+// Example 1: A single MCP23S17 device on SPI0, CS#0 with its SPI addr set to 0 and INTA output connected to GPIO25:
-+// dtoverlay=mcp23s17:s17-spi0-0-present=1,s17-spi0-0-int-gpio=25
-+//
-+// Example 2: Two MCP23S08 devices on SPI1, CS#0 with their addrs set to 2 and 3. Three MCP23S17 devices on SPI1, CS#1 with their addrs set to 0, 1 and 7:
-+// dtoverlay=spi1-2cs
-+// dtoverlay=mcp23s17:s08-spi1-0-present=12,s17-spi1-1-present=131
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ // disable spi-dev on spi0.0
-+ fragment at 0 {
-+ target = <&spidev0>;
-+ __dormant__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ // disable spi-dev on spi0.1
-+ fragment at 1 {
-+ target = <&spidev1>;
-+ __dormant__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ // disable spi-dev on spi1.0
-+ fragment at 2 {
-+ target-path = "spi1/spidev at 0";
-+ __dormant__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ // disable spi-dev on spi1.1
-+ fragment at 3 {
-+ target-path = "spi1/spidev at 1";
-+ __dormant__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ // disable spi-dev on spi1.2
-+ fragment at 4 {
-+ target-path = "spi1/spidev at 2";
-+ __dormant__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ // disable spi-dev on spi2.0
-+ fragment at 5 {
-+ target-path = "spi2/spidev at 0";
-+ __dormant__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ // disable spi-dev on spi2.1
-+ fragment at 6 {
-+ target-path = "spi2/spidev at 1";
-+ __dormant__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ // disable spi-dev on spi2.2
-+ fragment at 7 {
-+ target-path = "spi2/spidev at 2";
-+ __dormant__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ // enable one or more mcp23s08s on spi0.0
-+ fragment at 8 {
-+ target = <&spi0>;
-+ __dormant__ {
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ mcp23s08_00: mcp23s08 at 0 {
-+ compatible = "microchip,mcp23s08";
-+ gpio-controller;
-+ #gpio-cells = <2>;
-+ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s08-spi0-0-present parameter */
-+ reg = <0>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ #interrupt-cells=<2>;
-+ interrupts = <0 2>; /* 1st word overwritten by mcp23s08-spi0-0-int-gpio parameter */
-+ };
-+ };
-+ };
-+
-+ // enable one or more mcp23s08s on spi0.1
-+ fragment at 9 {
-+ target = <&spi0>;
-+ __dormant__ {
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ mcp23s08_01: mcp23s08 at 1 {
-+ compatible = "microchip,mcp23s08";
-+ gpio-controller;
-+ #gpio-cells = <2>;
-+ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s08-spi0-1-present parameter */
-+ reg = <1>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ #interrupt-cells=<2>;
-+ interrupts = <0 2>; /* 1st word overwritten by mcp23s08-spi0-1-int-gpio parameter */
-+ };
-+ };
-+ };
-+
-+ // enable one or more mcp23s08s on spi1.0
-+ fragment at 10 {
-+ target = <&spi1>;
-+ __dormant__ {
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ mcp23s08_10: mcp23s08 at 0 {
-+ compatible = "microchip,mcp23s08";
-+ gpio-controller;
-+ #gpio-cells = <2>;
-+ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s08-spi1-0-present parameter */
-+ reg = <0>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ #interrupt-cells=<2>;
-+ interrupts = <0 2>; /* 1st word overwritten by mcp23s08-spi1-0-int-gpio parameter */
-+ };
-+ };
-+ };
-+
-+ // enable one or more mcp23s08s on spi1.1
-+ fragment at 11 {
-+ target = <&spi1>;
-+ __dormant__ {
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ mcp23s08_11: mcp23s08 at 1 {
-+ compatible = "microchip,mcp23s08";
-+ gpio-controller;
-+ #gpio-cells = <2>;
-+ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s08-spi1-1-present parameter */
-+ reg = <1>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ #interrupt-cells=<2>;
-+ interrupts = <0 2>; /* 1st word overwritten by mcp23s08-spi1-1-int-gpio parameter */
-+ };
-+ };
-+ };
-+
-+ // enable one or more mcp23s08s on spi1.2
-+ fragment at 12 {
-+ target = <&spi1>;
-+ __dormant__ {
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ mcp23s08_12: mcp23s08 at 2 {
-+ compatible = "microchip,mcp23s08";
-+ gpio-controller;
-+ #gpio-cells = <2>;
-+ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s08-spi1-2-present parameter */
-+ reg = <2>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ #interrupt-cells=<2>;
-+ interrupts = <0 2>; /* 1st word overwritten by mcp23s08-spi1-2-int-gpio parameter */
-+ };
-+ };
-+ };
-+
-+ // enable one or more mcp23s08s on spi2.0
-+ fragment at 13 {
-+ target = <&spi2>;
-+ __dormant__ {
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ mcp23s08_20: mcp23s08 at 0 {
-+ compatible = "microchip,mcp23s08";
-+ gpio-controller;
-+ #gpio-cells = <2>;
-+ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s08-spi2-0-present parameter */
-+ reg = <0>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ #interrupt-cells=<2>;
-+ interrupts = <0 2>; /* 1st word overwritten by mcp23s08-spi2-0-int-gpio parameter */
-+ };
-+ };
-+ };
-+
-+ // enable one or more mcp23s08s on spi2.1
-+ fragment at 14 {
-+ target = <&spi2>;
-+ __dormant__ {
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ mcp23s08_21: mcp23s08 at 1 {
-+ compatible = "microchip,mcp23s08";
-+ gpio-controller;
-+ #gpio-cells = <2>;
-+ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s08-spi2-1-present parameter */
-+ reg = <1>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ #interrupt-cells=<2>;
-+ interrupts = <0 2>; /* 1st word overwritten by mcp23s08-spi2-1-int-gpio parameter */
-+ };
-+ };
-+ };
-+
-+ // enable one or more mcp23s08s on spi2.2
-+ fragment at 15 {
-+ target = <&spi2>;
-+ __dormant__ {
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ mcp23s08_22: mcp23s08 at 2 {
-+ compatible = "microchip,mcp23s08";
-+ gpio-controller;
-+ #gpio-cells = <2>;
-+ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s08-spi2-2-present parameter */
-+ reg = <2>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ #interrupt-cells=<2>;
-+ interrupts = <0 2>; /* 1st word overwritten by mcp23s08-spi2-2-int-gpio parameter */
-+ };
-+ };
-+ };
-+
-+ // enable one or more mcp23s17s on spi0.0
-+ fragment at 16 {
-+ target = <&spi0>;
-+ __dormant__ {
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ mcp23s17_00: mcp23s17 at 0 {
-+ compatible = "microchip,mcp23s17";
-+ gpio-controller;
-+ #gpio-cells = <2>;
-+ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s17-spi0-0-present parameter */
-+ reg = <0>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ #interrupt-cells=<2>;
-+ interrupts = <0 2>; /* 1st word overwritten by mcp23s17-spi0-0-int-gpio parameter */
-+ };
-+ };
-+ };
-+
-+ // enable one or more mcp23s17s on spi0.1
-+ fragment at 17 {
-+ target = <&spi0>;
-+ __dormant__ {
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ mcp23s17_01: mcp23s17 at 1 {
-+ compatible = "microchip,mcp23s17";
-+ gpio-controller;
-+ #gpio-cells = <2>;
-+ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s17-spi0-1-present parameter */
-+ reg = <1>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ #interrupt-cells=<2>;
-+ interrupts = <0 2>; /* 1st word overwritten by mcp23s17-spi0-1-int-gpio parameter */
-+ };
-+ };
-+ };
-+
-+ // enable one or more mcp23s17s on spi1.0
-+ fragment at 18 {
-+ target = <&spi1>;
-+ __dormant__ {
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ mcp23s17_10: mcp23s17 at 0 {
-+ compatible = "microchip,mcp23s17";
-+ gpio-controller;
-+ #gpio-cells = <2>;
-+ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s17-spi1-0-present parameter */
-+ reg = <0>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ #interrupt-cells=<2>;
-+ interrupts = <0 2>; /* 1st word overwritten by mcp23s17-spi1-0-int-gpio parameter */
-+ };
-+ };
-+ };
-+
-+ // enable one or more mcp23s17s on spi1.1
-+ fragment at 19 {
-+ target = <&spi1>;
-+ __dormant__ {
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ mcp23s17_11: mcp23s17 at 1 {
-+ compatible = "microchip,mcp23s17";
-+ gpio-controller;
-+ #gpio-cells = <2>;
-+ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s17-spi1-1-present parameter */
-+ reg = <1>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ #interrupt-cells=<2>;
-+ interrupts = <0 2>; /* 1st word overwritten by mcp23s17-spi1-1-int-gpio parameter */
-+ };
-+ };
-+ };
-+
-+ // enable one or more mcp23s17s on spi1.2
-+ fragment at 20 {
-+ target = <&spi1>;
-+ __dormant__ {
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ mcp23s17_12: mcp23s17 at 2 {
-+ compatible = "microchip,mcp23s17";
-+ gpio-controller;
-+ #gpio-cells = <2>;
-+ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s17-spi1-2-present parameter */
-+ reg = <2>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ #interrupt-cells=<2>;
-+ interrupts = <0 2>; /* 1st word overwritten by mcp23s17-spi1-2-int-gpio parameter */
-+ };
-+ };
-+ };
-+
-+ // enable one or more mcp23s17s on spi2.0
-+ fragment at 21 {
-+ target = <&spi2>;
-+ __dormant__ {
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ mcp23s17_20: mcp23s17 at 0 {
-+ compatible = "microchip,mcp23s17";
-+ gpio-controller;
-+ #gpio-cells = <2>;
-+ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s17-spi2-0-present parameter */
-+ reg = <0>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ #interrupt-cells=<2>;
-+ interrupts = <0 2>; /* 1st word overwritten by mcp23s17-spi2-0-int-gpio parameter */
-+ };
-+ };
-+ };
-+
-+ // enable one or more mcp23s17s on spi2.1
-+ fragment at 22 {
-+ target = <&spi2>;
-+ __dormant__ {
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ mcp23s17_21: mcp23s17 at 1 {
-+ compatible = "microchip,mcp23s17";
-+ gpio-controller;
-+ #gpio-cells = <2>;
-+ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s17-spi2-1-present parameter */
-+ reg = <1>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ #interrupt-cells=<2>;
-+ interrupts = <0 2>; /* 1st word overwritten by mcp23s17-spi2-1-int-gpio parameter */
-+ };
-+ };
-+ };
-+
-+ // enable one or more mcp23s17s on spi2.2
-+ fragment at 23 {
-+ target = <&spi2>;
-+ __dormant__ {
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ mcp23s17_22: mcp23s17 at 2 {
-+ compatible = "microchip,mcp23s17";
-+ gpio-controller;
-+ #gpio-cells = <2>;
-+ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s17-spi2-2-present parameter */
-+ reg = <2>;
-+ spi-max-frequency = <500000>;
-+ status = "okay";
-+ #interrupt-cells=<2>;
-+ interrupts = <0 2>; /* 1st word overwritten by mcp23s17-spi2-2-int-gpio parameter */
-+ };
-+ };
-+ };
-+
-+ // Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi0.0 as a input with no pull-up/down
-+ fragment at 24 {
-+ target = <&gpio>;
-+ __dormant__ {
-+ spi0_0_int_pins: spi0_0_int_pins {
-+ brcm,pins = <0>; /* overwritten by mcp23s08/17-spi0-0-int-gpio parameter */
-+ brcm,function = <0>;
-+ brcm,pull = <0>;
-+ };
-+ };
-+ };
-+
-+ // Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi0.1 as a input with no pull-up/down
-+ fragment at 25 {
-+ target = <&gpio>;
-+ __dormant__ {
-+ spi0_1_int_pins: spi0_1_int_pins {
-+ brcm,pins = <0>; /* overwritten by mcp23s08/17-spi0-1-int-gpio parameter */
-+ brcm,function = <0>;
-+ brcm,pull = <0>;
-+ };
-+ };
-+ };
-+
-+ // Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi1.0 as a input with no pull-up/down
-+ fragment at 26 {
-+ target = <&gpio>;
-+ __dormant__ {
-+ spi1_0_int_pins: spi1_0_int_pins {
-+ brcm,pins = <0>; /* overwritten by mcp23s08/17-spi1-0-int-gpio parameter */
-+ brcm,function = <0>;
-+ brcm,pull = <0>;
-+ };
-+ };
-+ };
-+
-+ // Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi1.1 as a input with no pull-up/down
-+ fragment at 27 {
-+ target = <&gpio>;
-+ __dormant__ {
-+ spi1_1_int_pins: spi1_1_int_pins {
-+ brcm,pins = <0>; /* overwritten by mcp23s08/17-spi1-1-int-gpio parameter */
-+ brcm,function = <0>;
-+ brcm,pull = <0>;
-+ };
-+ };
-+ };
-+
-+ // Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi1.2 as a input with no pull-up/down
-+ fragment at 28 {
-+ target = <&gpio>;
-+ __dormant__ {
-+ spi1_2_int_pins: spi1_2_int_pins {
-+ brcm,pins = <0>; /* overwritten by mcp23s08/17-spi1-2-int-gpio parameter */
-+ brcm,function = <0>;
-+ brcm,pull = <0>;
-+ };
-+ };
-+ };
-+
-+ // Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi2.0 as a input with no pull-up/down
-+ fragment at 29 {
-+ target = <&gpio>;
-+ __dormant__ {
-+ spi2_0_int_pins: spi2_0_int_pins {
-+ brcm,pins = <0>; /* overwritten by mcp23s08/17-spi2-0-int-gpio parameter */
-+ brcm,function = <0>;
-+ brcm,pull = <0>;
-+ };
-+ };
-+ };
-+
-+ // Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi2.1 as a input with no pull-up/down
-+ fragment at 30 {
-+ target = <&gpio>;
-+ __dormant__ {
-+ spi2_1_int_pins: spi2_1_int_pins {
-+ brcm,pins = <0>; /* overwritten by mcp23s08/17-spi2-1-int-gpio parameter */
-+ brcm,function = <0>;
-+ brcm,pull = <0>;
-+ };
-+ };
-+ };
-+
-+ // Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi2.2 as a input with no pull-up/down
-+ fragment at 31 {
-+ target = <&gpio>;
-+ __dormant__ {
-+ spi2_2_int_pins: spi2_2_int_pins {
-+ brcm,pins = <0>; /* overwritten by mcp23s08/17-spi2-2-int-gpio parameter */
-+ brcm,function = <0>;
-+ brcm,pull = <0>;
-+ };
-+ };
-+ };
-+
-+ // Enable interrupts for a mcp23s08 on spi0.0.
-+ // Use default active low interrupt signalling.
-+ fragment at 32 {
-+ target = <&mcp23s08_00>;
-+ __dormant__ {
-+ interrupt-parent = <&gpio>;
-+ interrupt-controller;
-+ };
-+ };
-+
-+ // Enable interrupts for a mcp23s08 on spi0.1.
-+ // Use default active low interrupt signalling.
-+ fragment at 33 {
-+ target = <&mcp23s08_01>;
-+ __dormant__ {
-+ interrupt-parent = <&gpio>;
-+ interrupt-controller;
-+ };
-+ };
-+
-+ // Enable interrupts for a mcp23s08 on spi1.0.
-+ // Use default active low interrupt signalling.
-+ fragment at 34 {
-+ target = <&mcp23s08_10>;
-+ __dormant__ {
-+ interrupt-parent = <&gpio>;
-+ interrupt-controller;
-+ };
-+ };
-+
-+ // Enable interrupts for a mcp23s08 on spi1.1.
-+ // Use default active low interrupt signalling.
-+ fragment at 35 {
-+ target = <&mcp23s08_11>;
-+ __dormant__ {
-+ interrupt-parent = <&gpio>;
-+ interrupt-controller;
-+ };
-+ };
-+
-+ // Enable interrupts for a mcp23s08 on spi1.2.
-+ // Use default active low interrupt signalling.
-+ fragment at 36 {
-+ target = <&mcp23s08_12>;
-+ __dormant__ {
-+ interrupt-parent = <&gpio>;
-+ interrupt-controller;
-+ };
-+ };
-+
-+ // Enable interrupts for a mcp23s08 on spi2.0.
-+ // Use default active low interrupt signalling.
-+ fragment at 37 {
-+ target = <&mcp23s08_20>;
-+ __dormant__ {
-+ interrupt-parent = <&gpio>;
-+ interrupt-controller;
-+ };
-+ };
-+
-+ // Enable interrupts for a mcp23s08 on spi2.1.
-+ // Use default active low interrupt signalling.
-+ fragment at 38 {
-+ target = <&mcp23s08_21>;
-+ __dormant__ {
-+ interrupt-parent = <&gpio>;
-+ interrupt-controller;
-+ };
-+ };
-+
-+ // Enable interrupts for a mcp23s08 on spi2.2.
-+ // Use default active low interrupt signalling.
-+ fragment at 39 {
-+ target = <&mcp23s08_22>;
-+ __dormant__ {
-+ interrupt-parent = <&gpio>;
-+ interrupt-controller;
-+ };
-+ };
-+
-+ // Enable interrupts for a mcp23s17 on spi0.0.
-+ // Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin.
-+ // Use default active low interrupt signalling.
-+ fragment at 40 {
-+ target = <&mcp23s17_00>;
-+ __dormant__ {
-+ interrupt-parent = <&gpio>;
-+ interrupt-controller;
-+ microchip,irq-mirror;
-+ };
-+ };
-+
-+ // Enable interrupts for a mcp23s17 on spi0.1.
-+ // Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin.
-+ // Configure INTA/B outputs of mcp23s08/17 as active low.
-+ fragment at 41 {
-+ target = <&mcp23s17_01>;
-+ __dormant__ {
-+ interrupt-parent = <&gpio>;
-+ interrupt-controller;
-+ microchip,irq-mirror;
-+ };
-+ };
-+
-+ // Enable interrupts for a mcp23s17 on spi1.0.
-+ // Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin.
-+ // Configure INTA/B outputs of mcp23s08/17 as active low.
-+ fragment at 42 {
-+ target = <&mcp23s17_10>;
-+ __dormant__ {
-+ interrupt-parent = <&gpio>;
-+ interrupt-controller;
-+ microchip,irq-mirror;
-+ };
-+ };
-+
-+ // Enable interrupts for a mcp23s17 on spi1.1.
-+ // Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin.
-+ // Configure INTA/B outputs of mcp23s08/17 as active low.
-+ fragment at 43 {
-+ target = <&mcp23s17_11>;
-+ __dormant__ {
-+ interrupt-parent = <&gpio>;
-+ interrupt-controller;
-+ microchip,irq-mirror;
-+ };
-+ };
-+
-+ // Enable interrupts for a mcp23s17 on spi1.2.
-+ // Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin.
-+ // Configure INTA/B outputs of mcp23s08/17 as active low.
-+ fragment at 44 {
-+ target = <&mcp23s17_12>;
-+ __dormant__ {
-+ interrupt-parent = <&gpio>;
-+ interrupt-controller;
-+ microchip,irq-mirror;
-+ };
-+ };
-+
-+ // Enable interrupts for a mcp23s17 on spi2.0.
-+ // Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin.
-+ // Configure INTA/B outputs of mcp23s08/17 as active low.
-+ fragment at 45 {
-+ target = <&mcp23s17_20>;
-+ __dormant__ {
-+ interrupt-parent = <&gpio>;
-+ interrupt-controller;
-+ microchip,irq-mirror;
-+ };
-+ };
-+
-+ // Enable interrupts for a mcp23s17 on spi2.1.
-+ // Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin.
-+ // Configure INTA/B outputs of mcp23s08/17 as active low.
-+ fragment at 46 {
-+ target = <&mcp23s17_21>;
-+ __dormant__ {
-+ interrupt-parent = <&gpio>;
-+ interrupt-controller;
-+ microchip,irq-mirror;
-+ };
-+ };
-+
-+ // Enable interrupts for a mcp23s17 on spi2.2.
-+ // Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin.
-+ // Configure INTA/B outputs of mcp23s08/17 as active low.
-+ fragment at 47 {
-+ target = <&mcp23s17_22>;
-+ __dormant__ {
-+ interrupt-parent = <&gpio>;
-+ interrupt-controller;
-+ microchip,irq-mirror;
-+ };
-+ };
-+
-+ __overrides__ {
-+ s08-spi0-0-present = <0>,"+0+8", <&mcp23s08_00>,"microchip,spi-present-mask:0";
-+ s08-spi0-1-present = <0>,"+1+9", <&mcp23s08_01>,"microchip,spi-present-mask:0";
-+ s08-spi1-0-present = <0>,"+2+10", <&mcp23s08_10>,"microchip,spi-present-mask:0";
-+ s08-spi1-1-present = <0>,"+3+11", <&mcp23s08_11>,"microchip,spi-present-mask:0";
-+ s08-spi1-2-present = <0>,"+4+12", <&mcp23s08_12>,"microchip,spi-present-mask:0";
-+ s08-spi2-0-present = <0>,"+5+13", <&mcp23s08_20>,"microchip,spi-present-mask:0";
-+ s08-spi2-1-present = <0>,"+6+14", <&mcp23s08_21>,"microchip,spi-present-mask:0";
-+ s08-spi2-2-present = <0>,"+7+15", <&mcp23s08_22>,"microchip,spi-present-mask:0";
-+ s17-spi0-0-present = <0>,"+0+16", <&mcp23s17_00>,"microchip,spi-present-mask:0";
-+ s17-spi0-1-present = <0>,"+1+17", <&mcp23s17_01>,"microchip,spi-present-mask:0";
-+ s17-spi1-0-present = <0>,"+2+18", <&mcp23s17_10>,"microchip,spi-present-mask:0";
-+ s17-spi1-1-present = <0>,"+3+19", <&mcp23s17_11>,"microchip,spi-present-mask:0";
-+ s17-spi1-2-present = <0>,"+4+20", <&mcp23s17_12>,"microchip,spi-present-mask:0";
-+ s17-spi2-0-present = <0>,"+5+21", <&mcp23s17_20>,"microchip,spi-present-mask:0";
-+ s17-spi2-1-present = <0>,"+6+22", <&mcp23s17_21>,"microchip,spi-present-mask:0";
-+ s17-spi2-2-present = <0>,"+7+23", <&mcp23s17_22>,"microchip,spi-present-mask:0";
-+ s08-spi0-0-int-gpio = <0>,"+24+32", <&spi0_0_int_pins>,"brcm,pins:0", <&mcp23s08_00>,"interrupts:0";
-+ s08-spi0-1-int-gpio = <0>,"+25+33", <&spi0_1_int_pins>,"brcm,pins:0", <&mcp23s08_01>,"interrupts:0";
-+ s08-spi1-0-int-gpio = <0>,"+26+34", <&spi1_0_int_pins>,"brcm,pins:0", <&mcp23s08_10>,"interrupts:0";
-+ s08-spi1-1-int-gpio = <0>,"+27+35", <&spi1_1_int_pins>,"brcm,pins:0", <&mcp23s08_11>,"interrupts:0";
-+ s08-spi1-2-int-gpio = <0>,"+28+36", <&spi1_2_int_pins>,"brcm,pins:0", <&mcp23s08_12>,"interrupts:0";
-+ s08-spi2-0-int-gpio = <0>,"+29+37", <&spi2_0_int_pins>,"brcm,pins:0", <&mcp23s08_20>,"interrupts:0";
-+ s08-spi2-1-int-gpio = <0>,"+30+38", <&spi2_1_int_pins>,"brcm,pins:0", <&mcp23s08_21>,"interrupts:0";
-+ s08-spi2-2-int-gpio = <0>,"+31+39", <&spi2_2_int_pins>,"brcm,pins:0", <&mcp23s08_22>,"interrupts:0";
-+ s17-spi0-0-int-gpio = <0>,"+24+40", <&spi0_0_int_pins>,"brcm,pins:0", <&mcp23s17_00>,"interrupts:0";
-+ s17-spi0-1-int-gpio = <0>,"+25+41", <&spi0_1_int_pins>,"brcm,pins:0", <&mcp23s17_01>,"interrupts:0";
-+ s17-spi1-0-int-gpio = <0>,"+26+42", <&spi1_0_int_pins>,"brcm,pins:0", <&mcp23s17_10>,"interrupts:0";
-+ s17-spi1-1-int-gpio = <0>,"+27+43", <&spi1_1_int_pins>,"brcm,pins:0", <&mcp23s17_11>,"interrupts:0";
-+ s17-spi1-2-int-gpio = <0>,"+28+44", <&spi1_2_int_pins>,"brcm,pins:0", <&mcp23s17_12>,"interrupts:0";
-+ s17-spi2-0-int-gpio = <0>,"+29+45", <&spi2_0_int_pins>,"brcm,pins:0", <&mcp23s17_20>,"interrupts:0";
-+ s17-spi2-1-int-gpio = <0>,"+30+46", <&spi2_1_int_pins>,"brcm,pins:0", <&mcp23s17_21>,"interrupts:0";
-+ s17-spi2-2-int-gpio = <0>,"+31+47", <&spi2_2_int_pins>,"brcm,pins:0", <&mcp23s17_22>,"interrupts:0";
-+ };
-+};
-+
diff --git a/target/linux/brcm2708/patches-4.4/0486-BCM270X_DT-Add-audio_pins-to-CM-dtb.patch b/target/linux/brcm2708/patches-4.4/0486-BCM270X_DT-Add-audio_pins-to-CM-dtb.patch
deleted file mode 100644
index a8a98e2..0000000
--- a/target/linux/brcm2708/patches-4.4/0486-BCM270X_DT-Add-audio_pins-to-CM-dtb.patch
+++ /dev/null
@@ -1,24 +0,0 @@
-From b6a9cfee231087657f8380ee4acc96f8fe9e9a51 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 19 Aug 2016 11:12:28 +0100
-Subject: [PATCH] BCM270X_DT: Add audio_pins to CM dtb
-
-Bring the CM .dtb in line with other others.
----
- arch/arm/boot/dts/bcm2708-rpi-cm.dts | 5 +++++
- 1 file changed, 5 insertions(+)
-
---- a/arch/arm/boot/dts/bcm2708-rpi-cm.dts
-+++ b/arch/arm/boot/dts/bcm2708-rpi-cm.dts
-@@ -35,6 +35,11 @@
- brcm,pins = <18 19 20 21>;
- brcm,function = <4>; /* alt0 */
- };
-+
-+ audio_pins: audio_pins {
-+ brcm,pins;
-+ brcm,function;
-+ };
- };
-
- &spi0 {
diff --git a/target/linux/brcm2708/patches-4.4/0487-BCM270X_DT-Don-t-enable-UART0-in-CM3-dtb.patch b/target/linux/brcm2708/patches-4.4/0487-BCM270X_DT-Don-t-enable-UART0-in-CM3-dtb.patch
deleted file mode 100644
index 7590ad6..0000000
--- a/target/linux/brcm2708/patches-4.4/0487-BCM270X_DT-Don-t-enable-UART0-in-CM3-dtb.patch
+++ /dev/null
@@ -1,37 +0,0 @@
-From dea7401406b48720cfea036cfcd03cdefe741116 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 19 Aug 2016 11:19:02 +0100
-Subject: [PATCH] BCM270X_DT: Don't enable UART0 in CM3 dtb
-
----
- arch/arm/boot/dts/bcm2710-rpi-cm3.dts | 12 ------------
- 1 file changed, 12 deletions(-)
-
---- a/arch/arm/boot/dts/bcm2710-rpi-cm3.dts
-+++ b/arch/arm/boot/dts/bcm2710-rpi-cm3.dts
-@@ -40,12 +40,6 @@
- brcm,function = <4>; /* alt0 */
- };
-
-- uart0_pins: uart0_pins {
-- brcm,pins;
-- brcm,function;
-- brcm,pull = <0 2>;
-- };
--
- audio_pins: audio_pins {
- brcm,pins;
- brcm,function;
-@@ -75,12 +69,6 @@
- status = "okay";
- };
-
--&uart0 {
-- pinctrl-names = "default";
-- pinctrl-0 = <&uart0_pins>;
-- status = "okay";
--};
--
- &spi0 {
- pinctrl-names = "default";
- pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
diff --git a/target/linux/brcm2708/patches-4.4/0488-overlays-Add-audremap-overlay.patch b/target/linux/brcm2708/patches-4.4/0488-overlays-Add-audremap-overlay.patch
deleted file mode 100644
index a46dee8..0000000
--- a/target/linux/brcm2708/patches-4.4/0488-overlays-Add-audremap-overlay.patch
+++ /dev/null
@@ -1,56 +0,0 @@
-From e0db21bda68cda5dbc4525ca7fe9528c74866359 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 19 Aug 2016 11:26:57 +0100
-Subject: [PATCH] overlays: Add audremap overlay
-
-The audremap overlay switches the PWM audio outputs to GPIO pins
-12 (L) and 13 (R).
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 6 ++++++
- arch/arm/boot/dts/overlays/audremap-overlay.dts | 14 ++++++++++++++
- 3 files changed, 21 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/audremap-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -18,6 +18,7 @@ dtbo-$(RPI_DT_OVERLAYS) += ads7846.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += akkordion-iqdacplus.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += at86rf233.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += audioinjector-wm8731-audio.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += audremap.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += bmp085_i2c-sensor.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += dht11.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += dionaudio-loco.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -253,6 +253,12 @@ Load: dtoverlay=audioinjector-wm8731-a
- Params: <None>
-
-
-+Name: audremap
-+Info: Switches PWM sound output to pins 12 & 13
-+Load: dtoverlay=audremap
-+Params: <None>
-+
-+
- Name: bmp085_i2c-sensor
- Info: Configures the BMP085/BMP180 digital barometric pressure and temperature
- sensors from Bosch Sensortec
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/audremap-overlay.dts
-@@ -0,0 +1,14 @@
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&audio_pins>;
-+ __overlay__ {
-+ brcm,pins = < 12 13 >;
-+ brcm,function = < 4 >; /* alt0 alt0 */
-+ };
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0489-overlays-Add-swap_lr-and-enable_jack-to-audremap.patch b/target/linux/brcm2708/patches-4.4/0489-overlays-Add-swap_lr-and-enable_jack-to-audremap.patch
deleted file mode 100644
index e8b31c5..0000000
--- a/target/linux/brcm2708/patches-4.4/0489-overlays-Add-swap_lr-and-enable_jack-to-audremap.patch
+++ /dev/null
@@ -1,50 +0,0 @@
-From 0c6470ece4ead2849ed4f5fcb0cb01fed1ee099f Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 19 Aug 2016 15:39:01 +0100
-Subject: [PATCH] overlays: Add swap_lr and enable_jack to audremap
-
-swap_lr causes the channels to be reversed, and enable_jack prevents the
-headphone output from being disabled.
-
-See: https://github.com/raspberrypi/linux/issues/1473
----
- arch/arm/boot/dts/overlays/README | 9 ++++++---
- arch/arm/boot/dts/overlays/audremap-overlay.dts | 7 ++++++-
- 2 files changed, 12 insertions(+), 4 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -254,9 +254,12 @@ Params: <None>
-
-
- Name: audremap
--Info: Switches PWM sound output to pins 12 & 13
--Load: dtoverlay=audremap
--Params: <None>
-+Info: Switches PWM sound output to pins 12 (Right) & 13 (Left)
-+Load: dtoverlay=audremap,<param>=<val>
-+Params: swap_lr Reverse the channel allocation, which will also
-+ swap the audio jack outputs (default off)
-+ enable_jack Don't switch off the audio jack output
-+ (default off)
-
-
- Name: bmp085_i2c-sensor
---- a/arch/arm/boot/dts/overlays/audremap-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/audremap-overlay.dts
-@@ -6,9 +6,14 @@
-
- fragment at 0 {
- target = <&audio_pins>;
-- __overlay__ {
-+ frag0: __overlay__ {
- brcm,pins = < 12 13 >;
- brcm,function = < 4 >; /* alt0 alt0 */
- };
- };
-+
-+ __overrides__ {
-+ swap_lr = <&frag0>, "swap_lr?";
-+ enable_jack = <&frag0>, "enable_jack?";
-+ };
- };
diff --git a/target/linux/brcm2708/patches-4.4/0490-overlays-Clarify-gpio-poweroff-semantics-in-README.patch b/target/linux/brcm2708/patches-4.4/0490-overlays-Clarify-gpio-poweroff-semantics-in-README.patch
deleted file mode 100644
index df39cb0..0000000
--- a/target/linux/brcm2708/patches-4.4/0490-overlays-Clarify-gpio-poweroff-semantics-in-README.patch
+++ /dev/null
@@ -1,24 +0,0 @@
-From 54c1a1acd6a8c4f467855c0e14e295420ad531ba Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 22 Aug 2016 11:56:04 +0100
-Subject: [PATCH] overlays: Clarify gpio-poweroff semantics in README
-
-1) GPIO pin is signalled on poweroff, not reboot.
-2) In RPi kernels, halt is equivalent to poweroff.
-
-See: https://github.com/raspberrypi/linux/issues/1600
----
- arch/arm/boot/dts/overlays/README | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -340,7 +340,7 @@ Params: gpio_pin Input pi
-
-
- Name: gpio-poweroff
--Info: Drives a GPIO high or low on reboot
-+Info: Drives a GPIO high or low on poweroff (including halt)
- Load: dtoverlay=gpio-poweroff,<param>=<val>
- Params: gpiopin GPIO for signalling (default 26)
-
diff --git a/target/linux/brcm2708/patches-4.4/0491-overlays-added-sc16is750-UART-over-I2C-1617.patch b/target/linux/brcm2708/patches-4.4/0491-overlays-added-sc16is750-UART-over-I2C-1617.patch
deleted file mode 100644
index 5639c1b..0000000
--- a/target/linux/brcm2708/patches-4.4/0491-overlays-added-sc16is750-UART-over-I2C-1617.patch
+++ /dev/null
@@ -1,81 +0,0 @@
-From 81d6acbdeecbca2db335d5c8362898df3d4fa8a3 Mon Sep 17 00:00:00 2001
-From: Georgii Staroselskii <gosha371 at gmail.com>
-Date: Tue, 23 Aug 2016 17:40:05 +0400
-Subject: [PATCH] overlays: added sc16is750 UART over I2C (#1617)
-
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 10 ++++++
- .../boot/dts/overlays/sc16is750-i2c-overlay.dts | 37 ++++++++++++++++++++++
- 3 files changed, 48 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/sc16is750-i2c-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -75,6 +75,7 @@ dtbo-$(RPI_DT_OVERLAYS) += rpi-ft5406.dt
- dtbo-$(RPI_DT_OVERLAYS) += rpi-proto.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += rpi-sense.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += rra-digidac1-wm8741-audio.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += sc16is750-i2c.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += sc16is752-spi1.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += sdhost.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += sdio.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -935,6 +935,16 @@ Load: dtoverlay=rra-digidac1-wm8741-au
- Params: <None>
-
-
-+Name: sc16is750-i2c
-+Info: Overlay for the NXP SC16IS750 UART with I2C Interface
-+ Enables the chip on I2C1 at 0x48. To select another address,
-+ please refer to table 10 in reference manual.
-+
-+Load: dtoverlay=sc16is750-i2c,<param>=<val>
-+Params: int_pin GPIO used for IRQ (default 24)
-+ addr Address (default 0x48)
-+
-+
- Name: sc16is752-spi1
- Info: Overlay for the NXP SC16IS752 Dual UART with SPI Interface
- Enables the chip on SPI1.
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/sc16is750-i2c-overlay.dts
-@@ -0,0 +1,37 @@
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&i2c_arm>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ sc16is750: sc16is750 at 48 {
-+ compatible = "nxp,sc16is750";
-+ reg = <0x48>; /* address */
-+ clocks = <&sc16is750_clk>;
-+ interrupt-parent = <&gpio>;
-+ interrupts = <24 2>; /* IRQ_TYPE_EDGE_FALLING */
-+ #gpio-cells = <2>;
-+
-+ sc16is750_clk: sc16is750_clk {
-+ compatible = "fixed-clock";
-+ #clock-cells = <0>;
-+ clock-frequency = <14745600>;
-+ };
-+ };
-+ };
-+ };
-+
-+
-+ __overrides__ {
-+ int_pin = <&sc16is750>,"interrupts:0";
-+ addr = <&sc16is750>,"reg:0";
-+ };
-+
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0492-Bluetooth-Fix-l2cap_sock_setsockopt-with-optname-BT_.patch b/target/linux/brcm2708/patches-4.4/0492-Bluetooth-Fix-l2cap_sock_setsockopt-with-optname-BT_.patch
deleted file mode 100644
index 76ce6a7..0000000
--- a/target/linux/brcm2708/patches-4.4/0492-Bluetooth-Fix-l2cap_sock_setsockopt-with-optname-BT_.patch
+++ /dev/null
@@ -1,33 +0,0 @@
-From 315bdca77a8cc7621ea5e469738df009dad62ace Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Amadeusz=20S=C5=82awi=C5=84ski?=
- <amadeusz.slawinski at tieto.com>
-Date: Thu, 14 Jul 2016 10:50:23 +0200
-Subject: [PATCH] Bluetooth: Fix l2cap_sock_setsockopt() with optname BT_RCVMTU
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-commit 23bc6ab0a0912146fd674a0becc758c3162baabc upstream.
-
-When we retrieve imtu value from userspace we should use 16 bit pointer
-cast instead of 32 as it's defined that way in headers. Fixes setsockopt
-calls on big-endian platforms.
-
-Signed-off-by: Amadeusz Sławiński <amadeusz.slawinski at tieto.com>
-Signed-off-by: Marcel Holtmann <marcel at holtmann.org>
-Signed-off-by: Greg Kroah-Hartman <gregkh at linuxfoundation.org>
----
- net/bluetooth/l2cap_sock.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/net/bluetooth/l2cap_sock.c
-+++ b/net/bluetooth/l2cap_sock.c
-@@ -817,7 +817,7 @@ static int l2cap_sock_setsockopt(struct
- break;
- }
-
-- if (get_user(opt, (u32 __user *) optval)) {
-+ if (get_user(opt, (u16 __user *) optval)) {
- err = -EFAULT;
- break;
- }
diff --git a/target/linux/brcm2708/patches-4.4/0493-config-Add-CONFIG_IPVLAN-module.patch b/target/linux/brcm2708/patches-4.4/0493-config-Add-CONFIG_IPVLAN-module.patch
deleted file mode 100644
index 1cbcd94..0000000
--- a/target/linux/brcm2708/patches-4.4/0493-config-Add-CONFIG_IPVLAN-module.patch
+++ /dev/null
@@ -1,30 +0,0 @@
-From 5006ec8b1834dd310147308a4335dfaa44f6f99e Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Tue, 23 Aug 2016 14:07:29 +0100
-Subject: [PATCH] config: Add CONFIG_IPVLAN module
-
----
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 2 files changed, 2 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -448,6 +448,7 @@ CONFIG_BONDING=m
- CONFIG_DUMMY=m
- CONFIG_IFB=m
- CONFIG_MACVLAN=m
-+CONFIG_IPVLAN=m
- CONFIG_NETCONSOLE=m
- CONFIG_TUN=m
- CONFIG_VETH=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -441,6 +441,7 @@ CONFIG_BONDING=m
- CONFIG_DUMMY=m
- CONFIG_IFB=m
- CONFIG_MACVLAN=m
-+CONFIG_IPVLAN=m
- CONFIG_NETCONSOLE=m
- CONFIG_TUN=m
- CONFIG_VETH=m
diff --git a/target/linux/brcm2708/patches-4.4/0494-config-Add-CONFIG_VXLAN-module.patch b/target/linux/brcm2708/patches-4.4/0494-config-Add-CONFIG_VXLAN-module.patch
deleted file mode 100644
index 4a70619..0000000
--- a/target/linux/brcm2708/patches-4.4/0494-config-Add-CONFIG_VXLAN-module.patch
+++ /dev/null
@@ -1,30 +0,0 @@
-From f05405f703a39200fe8458429d8b434a4bc90a9f Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Tue, 23 Aug 2016 14:08:55 +0100
-Subject: [PATCH] config: Add CONFIG_VXLAN module
-
----
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 2 files changed, 2 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -449,6 +449,7 @@ CONFIG_DUMMY=m
- CONFIG_IFB=m
- CONFIG_MACVLAN=m
- CONFIG_IPVLAN=m
-+CONFIG_VXLAN=m
- CONFIG_NETCONSOLE=m
- CONFIG_TUN=m
- CONFIG_VETH=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -442,6 +442,7 @@ CONFIG_DUMMY=m
- CONFIG_IFB=m
- CONFIG_MACVLAN=m
- CONFIG_IPVLAN=m
-+CONFIG_VXLAN=m
- CONFIG_NETCONSOLE=m
- CONFIG_TUN=m
- CONFIG_VETH=m
diff --git a/target/linux/brcm2708/patches-4.4/0495-Fixes-i2c_bcm2708-Write-to-FIFO-correctly-v2-1574.patch b/target/linux/brcm2708/patches-4.4/0495-Fixes-i2c_bcm2708-Write-to-FIFO-correctly-v2-1574.patch
deleted file mode 100644
index 39b3baa..0000000
--- a/target/linux/brcm2708/patches-4.4/0495-Fixes-i2c_bcm2708-Write-to-FIFO-correctly-v2-1574.patch
+++ /dev/null
@@ -1,48 +0,0 @@
-From 8ef9146c4479db1a672d7a88099e052a409624fa Mon Sep 17 00:00:00 2001
-From: Simon Maes <simonn.maes at gmail.com>
-Date: Mon, 29 Aug 2016 21:11:01 +0200
-Subject: [PATCH] Fixes i2c_bcm2708: Write to FIFO correctly - v2 (#1574)
-
-* i2c: fix i2c_bcm2708: Clear FIFO before sending data
-
-Make sure FIFO gets cleared before trying to send
-data in case of a repeated start (COMBINED=Y).
-
-* i2c: fix i2c_bcm2708: Only write to FIFO when not full
-
-Check if FIFO can accept data before writing.
-To avoid a peripheral read on the last iteration of a loop,
-both bcm2708_bsc_fifo_fill and ~drain are changed as well.
----
- drivers/i2c/busses/i2c-bcm2708.c | 8 ++++++--
- 1 file changed, 6 insertions(+), 2 deletions(-)
-
---- a/drivers/i2c/busses/i2c-bcm2708.c
-+++ b/drivers/i2c/busses/i2c-bcm2708.c
-@@ -115,13 +115,13 @@ static inline void bcm2708_bsc_reset(str
-
- static inline void bcm2708_bsc_fifo_drain(struct bcm2708_i2c *bi)
- {
-- while ((bcm2708_rd(bi, BSC_S) & BSC_S_RXD) && (bi->pos < bi->msg->len))
-+ while ((bi->pos < bi->msg->len) && (bcm2708_rd(bi, BSC_S) & BSC_S_RXD))
- bi->msg->buf[bi->pos++] = bcm2708_rd(bi, BSC_FIFO);
- }
-
- static inline void bcm2708_bsc_fifo_fill(struct bcm2708_i2c *bi)
- {
-- while ((bcm2708_rd(bi, BSC_S) & BSC_S_TXD) && (bi->pos < bi->msg->len))
-+ while ((bi->pos < bi->msg->len) && (bcm2708_rd(bi, BSC_S) & BSC_S_TXD))
- bcm2708_wr(bi, BSC_FIFO, bi->msg->buf[bi->pos++]);
- }
-
-@@ -155,6 +155,10 @@ static inline int bcm2708_bsc_setup(stru
- if ( (bi->nmsgs > 1) &&
- !(bi->msg[0].flags & I2C_M_RD) && (bi->msg[1].flags & I2C_M_RD) &&
- (bi->msg[0].addr == bi->msg[1].addr) && (bi->msg[0].len <= 16)) {
-+
-+ /* Clear FIFO */
-+ bcm2708_wr(bi, BSC_C, BSC_C_CLEAR_1);
-+
- /* Fill FIFO with entire write message (16 byte FIFO) */
- while (bi->pos < bi->msg->len) {
- bcm2708_wr(bi, BSC_FIFO, bi->msg->buf[bi->pos++]);
diff --git a/target/linux/brcm2708/patches-4.4/0496-bcm2835-sdhost-Don-t-exit-cmd-wait-loop-on-error.patch b/target/linux/brcm2708/patches-4.4/0496-bcm2835-sdhost-Don-t-exit-cmd-wait-loop-on-error.patch
deleted file mode 100644
index 36a02a4..0000000
--- a/target/linux/brcm2708/patches-4.4/0496-bcm2835-sdhost-Don-t-exit-cmd-wait-loop-on-error.patch
+++ /dev/null
@@ -1,63 +0,0 @@
-From 05bd3cc3309fd20d4c65d385181b7bbe3797eda6 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 2 Sep 2016 17:21:42 +0100
-Subject: [PATCH] bcm2835-sdhost: Don't exit cmd wait loop on error
-
-The FAIL flag can be set in the CMD register before command processing
-is complete, leading to spurious "failed to complete" errors. This has
-the effect of promoting harmless CRC7 errors during CMD1 processing
-into errors that can delay and even prevent booting.
-
-Also:
-1) Convert the last KERN_ERROR message in the register dumping to
- KERN_INFO.
-2) Remove an unnecessary reset call from bcm2835_sdhost_add_host.
-
-See: https://github.com/raspberrypi/linux/pull/1492
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- drivers/mmc/host/bcm2835-sdhost.c | 10 +++-------
- 1 file changed, 3 insertions(+), 7 deletions(-)
-
---- a/drivers/mmc/host/bcm2835-sdhost.c
-+++ b/drivers/mmc/host/bcm2835-sdhost.c
-@@ -373,7 +373,7 @@ static void bcm2835_sdhost_dumpregs(stru
- pr_info("%s: SDRSP2 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDRSP2));
-- pr_err("%s: SDRSP3 0x%08x\n",
-+ pr_info("%s: SDRSP3 0x%08x\n",
- mmc_hostname(host->mmc),
- bcm2835_sdhost_read(host, SDRSP3));
- pr_info("%s: SDHSTS 0x%08x\n",
-@@ -1183,9 +1183,8 @@ static void bcm2835_sdhost_finish_comman
- retries = 1; // We've already waited long enough this time
- }
-
-- retries = host->cmd_quick_poll_retries;
- for (sdcmd = bcm2835_sdhost_read(host, SDCMD);
-- (sdcmd & SDCMD_NEW_FLAG) && !(sdcmd & SDCMD_FAIL_FLAG) && retries;
-+ (sdcmd & SDCMD_NEW_FLAG) && retries;
- retries--) {
- cpu_relax();
- sdcmd = bcm2835_sdhost_read(host, SDCMD);
-@@ -1208,8 +1207,7 @@ static void bcm2835_sdhost_finish_comman
- usleep_range(1, 10);
- spin_lock_irqsave(&host->lock, *irq_flags);
- sdcmd = bcm2835_sdhost_read(host, SDCMD);
-- if (!(sdcmd & SDCMD_NEW_FLAG) ||
-- (sdcmd & SDCMD_FAIL_FLAG))
-+ if (!(sdcmd & SDCMD_NEW_FLAG))
- break;
- }
- }
-@@ -1892,8 +1890,6 @@ int bcm2835_sdhost_add_host(struct bcm28
-
- mmc = host->mmc;
-
-- bcm2835_sdhost_reset_internal(host);
--
- mmc->f_max = host->max_clk;
- mmc->f_min = host->max_clk / SDCDIV_MAX_CDIV;
-
diff --git a/target/linux/brcm2708/patches-4.4/0497-BCM270X_DT-Use-bcm2835-sdhost-on-Compute-Module.patch b/target/linux/brcm2708/patches-4.4/0497-BCM270X_DT-Use-bcm2835-sdhost-on-Compute-Module.patch
deleted file mode 100644
index 0478ec6..0000000
--- a/target/linux/brcm2708/patches-4.4/0497-BCM270X_DT-Use-bcm2835-sdhost-on-Compute-Module.patch
+++ /dev/null
@@ -1,30 +0,0 @@
-From 046dc73b641d0c8405336e52609d5f79d95d522a Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 2 Sep 2016 14:35:37 +0100
-Subject: [PATCH] BCM270X_DT: Use bcm2835-sdhost on Compute Module
-
-With the preceding commit:
-
- bcm2835-sdhost: Don't exit cmd wait loop on error
-
-it is safe to use the bcm2835-sdhost driver on the Compute Module.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/bcm2708-rpi-cm.dtsi | 4 ++--
- 1 file changed, 2 insertions(+), 2 deletions(-)
-
---- a/arch/arm/boot/dts/bcm2708-rpi-cm.dtsi
-+++ b/arch/arm/boot/dts/bcm2708-rpi-cm.dtsi
-@@ -23,9 +23,9 @@
- };
-
-
--&mmc {
-+&sdhost {
- pinctrl-names = "default";
-- pinctrl-0 = <&mmc_pins>;
-+ pinctrl-0 = <&sdhost_pins>;
- non-removable;
- bus-width = <4>;
- status = "okay";
diff --git a/target/linux/brcm2708/patches-4.4/0498-fbmem-Ensure-that-parameters-are-properly-checked-wi.patch b/target/linux/brcm2708/patches-4.4/0498-fbmem-Ensure-that-parameters-are-properly-checked-wi.patch
deleted file mode 100644
index 63a4bfc..0000000
--- a/target/linux/brcm2708/patches-4.4/0498-fbmem-Ensure-that-parameters-are-properly-checked-wi.patch
+++ /dev/null
@@ -1,27 +0,0 @@
-From 6ff979aa3e2dad734fa06670e56c9531d9a9015f Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Wed, 7 Sep 2016 16:57:59 +0100
-Subject: [PATCH] fbmem: Ensure that parameters are properly checked within
- fb_copyarea_user
-
----
- drivers/video/fbdev/core/fbmem.c | 8 +++++++-
- 1 file changed, 7 insertions(+), 1 deletion(-)
-
---- a/drivers/video/fbdev/core/fbmem.c
-+++ b/drivers/video/fbdev/core/fbmem.c
-@@ -1090,7 +1090,13 @@ static int fb_copyarea_user(struct fb_in
- int ret = 0;
- if (!lock_fb_info(info))
- return -ENODEV;
-- if (copy->dx + copy->width > info->var.xres ||
-+ if (copy->dx >= info->var.xres ||
-+ copy->sx >= info->var.xres ||
-+ copy->width > info->var.xres ||
-+ copy->dy >= info->var.yres ||
-+ copy->sy >= info->var.yres ||
-+ copy->height > info->var.yres ||
-+ copy->dx + copy->width > info->var.xres ||
- copy->sx + copy->width > info->var.xres ||
- copy->dy + copy->height > info->var.yres ||
- copy->sy + copy->height > info->var.yres) {
diff --git a/target/linux/brcm2708/patches-4.4/0499-config-Enabled-SENSORS_INA2XX-module.patch b/target/linux/brcm2708/patches-4.4/0499-config-Enabled-SENSORS_INA2XX-module.patch
deleted file mode 100644
index c2bc9f8..0000000
--- a/target/linux/brcm2708/patches-4.4/0499-config-Enabled-SENSORS_INA2XX-module.patch
+++ /dev/null
@@ -1,30 +0,0 @@
-From 3be9030c762e542e0c04108844bb3b4a1ada65db Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Fri, 9 Sep 2016 19:35:13 +0100
-Subject: [PATCH] config: Enabled SENSORS_INA2XX module
-
----
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 2 files changed, 2 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -649,6 +649,7 @@ CONFIG_HWMON=m
- CONFIG_SENSORS_LM75=m
- CONFIG_SENSORS_SHT21=m
- CONFIG_SENSORS_SHTC1=m
-+CONFIG_SENSORS_INA2XX=m
- CONFIG_THERMAL=y
- CONFIG_THERMAL_BCM2835=y
- CONFIG_WATCHDOG=y
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -641,6 +641,7 @@ CONFIG_HWMON=m
- CONFIG_SENSORS_LM75=m
- CONFIG_SENSORS_SHT21=m
- CONFIG_SENSORS_SHTC1=m
-+CONFIG_SENSORS_INA2XX=m
- CONFIG_THERMAL=y
- CONFIG_THERMAL_BCM2835=y
- CONFIG_WATCHDOG=y
diff --git a/target/linux/brcm2708/patches-4.4/0500-overlays-Add-dpi18-overlay-1634.patch b/target/linux/brcm2708/patches-4.4/0500-overlays-Add-dpi18-overlay-1634.patch
deleted file mode 100644
index dff1e2d..0000000
--- a/target/linux/brcm2708/patches-4.4/0500-overlays-Add-dpi18-overlay-1634.patch
+++ /dev/null
@@ -1,75 +0,0 @@
-From 729a4f56f3db3ad4ec5dbc740312abf8d44c183d Mon Sep 17 00:00:00 2001
-From: Phil Elwell <pelwell at users.noreply.github.com>
-Date: Mon, 12 Sep 2016 13:46:56 +0100
-Subject: [PATCH] overlays: Add dpi18 overlay (#1634)
-
-Add support for 18-bit DPI displays. Although the dpi24 overlay could
-be used, this overlay leaves GPIOs 22-27 free for other uses.
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 8 +++++++
- arch/arm/boot/dts/overlays/dpi18-overlay.dts | 31 ++++++++++++++++++++++++++++
- 3 files changed, 40 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/dpi18-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -22,6 +22,7 @@ dtbo-$(RPI_DT_OVERLAYS) += audremap.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += bmp085_i2c-sensor.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += dht11.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += dionaudio-loco.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += dpi18.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += dpi24.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += dwc-otg.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += dwc2.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -283,6 +283,14 @@ Load: dtoverlay=dionaudio-loco
- Params: <None>
-
-
-+Name: dpi18
-+Info: Overlay for a generic 18-bit DPI display
-+ This uses GPIOs 0-21 (so no I2C, uart etc.), and activates the output
-+ 2-3 seconds after the kernel has started.
-+Load: dtoverlay=dpi18
-+Params: <None>
-+
-+
- Name: dpi24
- Info: Overlay for a generic 24-bit DPI display
- This uses GPIOs 0-27 (so no I2C, uart etc.), and activates the output
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/dpi18-overlay.dts
-@@ -0,0 +1,31 @@
-+/dts-v1/;
-+/plugin/;
-+
-+/{
-+ compatible = "brcm,bcm2708";
-+
-+ // There is no DPI driver module, but we need a platform device
-+ // node (that doesn't already use pinctrl) to hang the pinctrl
-+ // reference on - leds will do
-+
-+ fragment at 0 {
-+ target = <&leds>;
-+ __overlay__ {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&dpi18_pins>;
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ dpi18_pins: dpi18_pins {
-+ brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11
-+ 12 13 14 15 16 17 18 19 20
-+ 21>;
-+ brcm,function = <6>; /* alt2 */
-+ brcm,pull = <0>; /* no pull */
-+ };
-+ };
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0502-drm-vc4-Allow-some-more-signals-to-be-packed-with-un.patch b/target/linux/brcm2708/patches-4.4/0502-drm-vc4-Allow-some-more-signals-to-be-packed-with-un.patch
deleted file mode 100644
index e71e316..0000000
--- a/target/linux/brcm2708/patches-4.4/0502-drm-vc4-Allow-some-more-signals-to-be-packed-with-un.patch
+++ /dev/null
@@ -1,38 +0,0 @@
-From c01673fc785dd4646a9cf3abf1821d90fde2aff2 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 30 Aug 2016 13:57:38 -0700
-Subject: [PATCH] drm/vc4: Allow some more signals to be packed with uniform
- resets.
-
-The intent was to make sure people don't sneak in a small immediate or
-something to change the interpretation of the uniform update args, but
-these signals are just fine.
-
-Fixes a validation failure in the current X server on some Render
-operation.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 313a61d30761217ce4383018de1cc0d5d503a376)
----
- drivers/gpu/drm/vc4/vc4_validate_shaders.c | 10 ++++++++--
- 1 file changed, 8 insertions(+), 2 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_validate_shaders.c
-+++ b/drivers/gpu/drm/vc4/vc4_validate_shaders.c
-@@ -309,8 +309,14 @@ validate_uniform_address_write(struct vc
- * of uniforms on each side. However, this scheme is easy to
- * validate so it's all we allow for now.
- */
--
-- if (QPU_GET_FIELD(inst, QPU_SIG) != QPU_SIG_NONE) {
-+ switch (QPU_GET_FIELD(inst, QPU_SIG)) {
-+ case QPU_SIG_NONE:
-+ case QPU_SIG_SCOREBOARD_UNLOCK:
-+ case QPU_SIG_COLOR_LOAD:
-+ case QPU_SIG_LOAD_TMU0:
-+ case QPU_SIG_LOAD_TMU1:
-+ break;
-+ default:
- DRM_ERROR("uniforms address change must be "
- "normal math\n");
- return false;
diff --git a/target/linux/brcm2708/patches-4.4/0503-raspberrypi-firmware-Export-the-general-transaction-.patch b/target/linux/brcm2708/patches-4.4/0503-raspberrypi-firmware-Export-the-general-transaction-.patch
deleted file mode 100644
index aefcf36..0000000
--- a/target/linux/brcm2708/patches-4.4/0503-raspberrypi-firmware-Export-the-general-transaction-.patch
+++ /dev/null
@@ -1,42 +0,0 @@
-From 6d7d5a0e3fd5885dd75ce2bc1e345513cf5eb22d Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Wed, 14 Sep 2016 09:16:19 +0100
-Subject: [PATCH] raspberrypi-firmware: Export the general transaction
- function.
-
-The vc4-firmware-kms module is going to be doing the MBOX FB call.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/firmware/raspberrypi.c | 3 ++-
- include/soc/bcm2835/raspberrypi-firmware.h | 1 +
- 2 files changed, 3 insertions(+), 1 deletion(-)
-
---- a/drivers/firmware/raspberrypi.c
-+++ b/drivers/firmware/raspberrypi.c
-@@ -42,7 +42,7 @@ static void response_callback(struct mbo
- * Sends a request to the firmware through the BCM2835 mailbox driver,
- * and synchronously waits for the reply.
- */
--static int
-+int
- rpi_firmware_transaction(struct rpi_firmware *fw, u32 chan, u32 data)
- {
- u32 message = MBOX_MSG(chan, data);
-@@ -63,6 +63,7 @@ rpi_firmware_transaction(struct rpi_firm
-
- return ret;
- }
-+EXPORT_SYMBOL_GPL(rpi_firmware_transaction);
-
- /**
- * rpi_firmware_property_list - Submit firmware property list
---- a/include/soc/bcm2835/raspberrypi-firmware.h
-+++ b/include/soc/bcm2835/raspberrypi-firmware.h
-@@ -129,5 +129,6 @@ int rpi_firmware_property(struct rpi_fir
- int rpi_firmware_property_list(struct rpi_firmware *fw,
- void *data, size_t tag_size);
- struct rpi_firmware *rpi_firmware_get(struct device_node *firmware_node);
-+int rpi_firmware_transaction(struct rpi_firmware *fw, u32 chan, u32 data);
-
- #endif /* __SOC_RASPBERRY_FIRMWARE_H__ */
diff --git a/target/linux/brcm2708/patches-4.4/0504-raspberrypi-firmware-Define-the-MBOX-channel-in-the-.patch b/target/linux/brcm2708/patches-4.4/0504-raspberrypi-firmware-Define-the-MBOX-channel-in-the-.patch
deleted file mode 100644
index b5a8065..0000000
--- a/target/linux/brcm2708/patches-4.4/0504-raspberrypi-firmware-Define-the-MBOX-channel-in-the-.patch
+++ /dev/null
@@ -1,21 +0,0 @@
-From 662f4d7f0f880aa37e3eb6ef1022655e831e855a Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Wed, 14 Sep 2016 09:18:09 +0100
-Subject: [PATCH] raspberrypi-firmware: Define the MBOX channel in the header.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- include/soc/bcm2835/raspberrypi-firmware.h | 2 ++
- 1 file changed, 2 insertions(+)
-
---- a/include/soc/bcm2835/raspberrypi-firmware.h
-+++ b/include/soc/bcm2835/raspberrypi-firmware.h
-@@ -12,6 +12,8 @@
- #include <linux/types.h>
- #include <linux/of_device.h>
-
-+#define RPI_FIRMWARE_CHAN_FB 1
-+
- struct rpi_firmware;
-
- enum rpi_firmware_property_status {
diff --git a/target/linux/brcm2708/patches-4.4/0505-drm-vc4-Add-a-mode-for-using-the-closed-firmware-for.patch b/target/linux/brcm2708/patches-4.4/0505-drm-vc4-Add-a-mode-for-using-the-closed-firmware-for.patch
deleted file mode 100644
index e6baeb7..0000000
--- a/target/linux/brcm2708/patches-4.4/0505-drm-vc4-Add-a-mode-for-using-the-closed-firmware-for.patch
+++ /dev/null
@@ -1,776 +0,0 @@
-From 96bd31d9a82377b04c72c853f3381f34c4985587 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Wed, 14 Sep 2016 08:39:33 +0100
-Subject: [PATCH] drm/vc4: Add a mode for using the closed firmware for
- display.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/Makefile | 1 +
- drivers/gpu/drm/vc4/vc4_crtc.c | 13 +
- drivers/gpu/drm/vc4/vc4_drv.c | 10 +-
- drivers/gpu/drm/vc4/vc4_drv.h | 7 +
- drivers/gpu/drm/vc4/vc4_firmware_kms.c | 660 +++++++++++++++++++++++++++++++++
- 5 files changed, 689 insertions(+), 2 deletions(-)
- create mode 100644 drivers/gpu/drm/vc4/vc4_firmware_kms.c
-
---- a/drivers/gpu/drm/vc4/Makefile
-+++ b/drivers/gpu/drm/vc4/Makefile
-@@ -9,6 +9,7 @@ vc4-y := \
- vc4_drv.o \
- vc4_dpi.o \
- vc4_dsi.o \
-+ vc4_firmware_kms.o \
- vc4_kms.o \
- vc4_gem.o \
- vc4_hdmi.o \
---- a/drivers/gpu/drm/vc4/vc4_crtc.c
-+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
-@@ -151,6 +151,9 @@ int vc4_crtc_get_scanoutpos(struct drm_d
- int vblank_lines;
- int ret = 0;
-
-+ if (vc4->firmware_kms)
-+ return 0;
-+
- /*
- * XXX Doesn't work well in interlaced mode yet, partially due
- * to problems in vc4 kms or drm core interlaced mode handling,
-@@ -639,6 +642,11 @@ int vc4_enable_vblank(struct drm_device
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_crtc *vc4_crtc = vc4->crtc[crtc_id];
-
-+ if (vc4->firmware_kms) {
-+ /* XXX: Can we mask the SMI interrupt? */
-+ return 0;
-+ }
-+
- CRTC_WRITE(PV_INTEN, PV_INT_VFP_START);
-
- return 0;
-@@ -649,6 +657,11 @@ void vc4_disable_vblank(struct drm_devic
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct vc4_crtc *vc4_crtc = vc4->crtc[crtc_id];
-
-+ if (vc4->firmware_kms) {
-+ /* XXX: Can we mask the SMI interrupt? */
-+ return;
-+ }
-+
- CRTC_WRITE(PV_INTEN, 0);
- }
-
---- a/drivers/gpu/drm/vc4/vc4_drv.c
-+++ b/drivers/gpu/drm/vc4/vc4_drv.c
-@@ -47,10 +47,15 @@ void __iomem *vc4_ioremap_regs(struct pl
-
- static void vc4_drm_preclose(struct drm_device *dev, struct drm_file *file)
- {
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
- struct drm_crtc *crtc;
-
-- list_for_each_entry(crtc, &dev->mode_config.crtc_list, head)
-- vc4_cancel_page_flip(crtc, file);
-+ list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) {
-+ if (vc4->firmware_kms)
-+ vc4_fkms_cancel_page_flip(crtc, file);
-+ else
-+ vc4_cancel_page_flip(crtc, file);
-+ }
- }
-
- void vc4_dump_regs32(const struct debugfs_reg32 *regs, unsigned int num_regs,
-@@ -331,6 +336,7 @@ static struct platform_driver *const com
- &vc4_dsi_driver,
- &vc4_hvs_driver,
- &vc4_crtc_driver,
-+ &vc4_firmware_kms_driver,
- &vc4_v3d_driver,
- };
-
---- a/drivers/gpu/drm/vc4/vc4_drv.h
-+++ b/drivers/gpu/drm/vc4/vc4_drv.h
-@@ -14,6 +14,9 @@ struct debugfs_reg32;
- struct vc4_dev {
- struct drm_device *dev;
-
-+ bool firmware_kms;
-+ struct rpi_firmware *firmware;
-+
- struct vc4_hdmi *hdmi;
- struct vc4_hvs *hvs;
- struct vc4_crtc *crtc[3];
-@@ -461,6 +464,10 @@ int vc4_dpi_debugfs_regs(struct seq_file
- extern struct platform_driver vc4_dsi_driver;
- int vc4_dsi_debugfs_regs(struct seq_file *m, void *unused);
-
-+/* vc4_firmware_kms.c */
-+extern struct platform_driver vc4_firmware_kms_driver;
-+void vc4_fkms_cancel_page_flip(struct drm_crtc *crtc, struct drm_file *file);
-+
- /* vc4_gem.c */
- void vc4_gem_init(struct drm_device *dev);
- void vc4_gem_destroy(struct drm_device *dev);
---- /dev/null
-+++ b/drivers/gpu/drm/vc4/vc4_firmware_kms.c
-@@ -0,0 +1,660 @@
-+/*
-+ * Copyright (C) 2016 Broadcom
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ */
-+
-+/**
-+ * DOC: VC4 firmware KMS module.
-+ *
-+ * As a hack to get us from the current closed source driver world
-+ * toward a totally open stack, implement KMS on top of the Raspberry
-+ * Pi's firmware display stack.
-+ */
-+
-+#include "drm_atomic.h"
-+#include "drm_atomic_helper.h"
-+#include "drm_plane_helper.h"
-+#include "drm_crtc_helper.h"
-+#include "linux/clk.h"
-+#include "linux/debugfs.h"
-+#include "drm_fb_cma_helper.h"
-+#include "linux/component.h"
-+#include "linux/of_device.h"
-+#include "vc4_drv.h"
-+#include "vc4_regs.h"
-+#include <soc/bcm2835/raspberrypi-firmware.h>
-+
-+/* The firmware delivers a vblank interrupt to us through the SMI
-+ * hardware, which has only this one register.
-+ */
-+#define SMICS 0x0
-+#define SMICS_INTERRUPTS (BIT(9) | BIT(10) | BIT(11))
-+
-+struct vc4_crtc {
-+ struct drm_crtc base;
-+ struct drm_encoder *encoder;
-+ struct drm_connector *connector;
-+ void __iomem *regs;
-+
-+ struct drm_pending_vblank_event *event;
-+};
-+
-+static inline struct vc4_crtc *to_vc4_crtc(struct drm_crtc *crtc)
-+{
-+ return container_of(crtc, struct vc4_crtc, base);
-+}
-+
-+struct vc4_fkms_encoder {
-+ struct drm_encoder base;
-+};
-+
-+static inline struct vc4_fkms_encoder *
-+to_vc4_fkms_encoder(struct drm_encoder *encoder)
-+{
-+ return container_of(encoder, struct vc4_fkms_encoder, base);
-+}
-+
-+/* VC4 FKMS connector KMS struct */
-+struct vc4_fkms_connector {
-+ struct drm_connector base;
-+
-+ /* Since the connector is attached to just the one encoder,
-+ * this is the reference to it so we can do the best_encoder()
-+ * hook.
-+ */
-+ struct drm_encoder *encoder;
-+};
-+
-+static inline struct vc4_fkms_connector *
-+to_vc4_fkms_connector(struct drm_connector *connector)
-+{
-+ return container_of(connector, struct vc4_fkms_connector, base);
-+}
-+
-+/* Firmware's structure for making an FB mbox call. */
-+struct fbinfo_s {
-+ u32 xres, yres, xres_virtual, yres_virtual;
-+ u32 pitch, bpp;
-+ u32 xoffset, yoffset;
-+ u32 base;
-+ u32 screen_size;
-+ u16 cmap[256];
-+};
-+
-+struct vc4_fkms_plane {
-+ struct drm_plane base;
-+ struct fbinfo_s *fbinfo;
-+ dma_addr_t fbinfo_bus_addr;
-+ u32 pitch;
-+};
-+
-+static inline struct vc4_fkms_plane *to_vc4_fkms_plane(struct drm_plane *plane)
-+{
-+ return (struct vc4_fkms_plane *)plane;
-+}
-+
-+/* Turns the display on/off. */
-+static int vc4_plane_set_primary_blank(struct drm_plane *plane, bool blank)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(plane->dev);
-+
-+ u32 packet = blank;
-+ return rpi_firmware_property(vc4->firmware,
-+ RPI_FIRMWARE_FRAMEBUFFER_BLANK,
-+ &packet, sizeof(packet));
-+}
-+
-+static void vc4_primary_plane_atomic_update(struct drm_plane *plane,
-+ struct drm_plane_state *old_state)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(plane->dev);
-+ struct vc4_fkms_plane *vc4_plane = to_vc4_fkms_plane(plane);
-+ struct drm_plane_state *state = plane->state;
-+ struct drm_framebuffer *fb = state->fb;
-+ struct drm_gem_cma_object *bo = drm_fb_cma_get_gem_obj(fb, 0);
-+ volatile struct fbinfo_s *fbinfo = vc4_plane->fbinfo;
-+ u32 bpp = 32;
-+ int ret;
-+
-+ vc4_plane_set_primary_blank(plane, false);
-+
-+ fbinfo->xres = state->crtc_w;
-+ fbinfo->yres = state->crtc_h;
-+ fbinfo->xres_virtual = state->crtc_w;
-+ fbinfo->yres_virtual = state->crtc_h;
-+ fbinfo->bpp = bpp;
-+ fbinfo->xoffset = state->crtc_x;
-+ fbinfo->yoffset = state->crtc_y;
-+ fbinfo->base = bo->paddr + fb->offsets[0];
-+ fbinfo->pitch = fb->pitches[0];
-+ /* A bug in the firmware makes it so that if the fb->base is
-+ * set to nonzero, the configured pitch gets overwritten with
-+ * the previous pitch. So, to get the configured pitch
-+ * recomputed, we have to make it allocate itself a new buffer
-+ * in VC memory, first.
-+ */
-+ if (vc4_plane->pitch != fb->pitches[0]) {
-+ u32 saved_base = fbinfo->base;
-+ fbinfo->base = 0;
-+
-+ ret = rpi_firmware_transaction(vc4->firmware,
-+ RPI_FIRMWARE_CHAN_FB,
-+ vc4_plane->fbinfo_bus_addr);
-+ fbinfo->base = saved_base;
-+
-+ vc4_plane->pitch = fbinfo->pitch;
-+ WARN_ON_ONCE(vc4_plane->pitch != fb->pitches[0]);
-+ }
-+
-+ ret = rpi_firmware_transaction(vc4->firmware,
-+ RPI_FIRMWARE_CHAN_FB,
-+ vc4_plane->fbinfo_bus_addr);
-+ WARN_ON_ONCE(fbinfo->pitch != fb->pitches[0]);
-+ WARN_ON_ONCE(fbinfo->base != bo->paddr + fb->offsets[0]);
-+}
-+
-+static void vc4_primary_plane_atomic_disable(struct drm_plane *plane,
-+ struct drm_plane_state *old_state)
-+{
-+ vc4_plane_set_primary_blank(plane, true);
-+}
-+
-+static void vc4_cursor_plane_atomic_update(struct drm_plane *plane,
-+ struct drm_plane_state *old_state)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(plane->dev);
-+ struct drm_plane_state *state = plane->state;
-+ struct drm_framebuffer *fb = state->fb;
-+ struct drm_gem_cma_object *bo = drm_fb_cma_get_gem_obj(fb, 0);
-+ int ret;
-+ u32 packet_state[] = { true, state->crtc_x, state->crtc_y, 0 };
-+ u32 packet_info[] = { state->crtc_w, state->crtc_h,
-+ 0, /* unused */
-+ bo->paddr + fb->offsets[0],
-+ 0, 0, /* hotx, hoty */};
-+ WARN_ON_ONCE(fb->pitches[0] != state->crtc_w * 4);
-+ WARN_ON_ONCE(fb->bits_per_pixel != 32);
-+
-+ ret = rpi_firmware_property(vc4->firmware,
-+ RPI_FIRMWARE_SET_CURSOR_STATE,
-+ &packet_state,
-+ sizeof(packet_state));
-+ if (ret || packet_state[0] != 0)
-+ DRM_ERROR("Failed to set cursor state: 0x%08x\n", packet_state[0]);
-+
-+ ret = rpi_firmware_property(vc4->firmware,
-+ RPI_FIRMWARE_SET_CURSOR_INFO,
-+ &packet_info,
-+ sizeof(packet_info));
-+ if (ret || packet_info[0] != 0)
-+ DRM_ERROR("Failed to set cursor info: 0x%08x\n", packet_info[0]);
-+}
-+
-+static void vc4_cursor_plane_atomic_disable(struct drm_plane *plane,
-+ struct drm_plane_state *old_state)
-+{
-+ struct vc4_dev *vc4 = to_vc4_dev(plane->dev);
-+ u32 packet_state[] = { false, 0, 0, 0 };
-+ int ret;
-+
-+ ret = rpi_firmware_property(vc4->firmware,
-+ RPI_FIRMWARE_SET_CURSOR_STATE,
-+ &packet_state,
-+ sizeof(packet_state));
-+ if (ret || packet_state[0] != 0)
-+ DRM_ERROR("Failed to set cursor state: 0x%08x\n", packet_state[0]);
-+}
-+
-+static int vc4_plane_atomic_check(struct drm_plane *plane,
-+ struct drm_plane_state *state)
-+{
-+ return 0;
-+}
-+
-+static void vc4_plane_destroy(struct drm_plane *plane)
-+{
-+ drm_plane_helper_disable(plane);
-+ drm_plane_cleanup(plane);
-+}
-+
-+static const struct drm_plane_funcs vc4_plane_funcs = {
-+ .update_plane = drm_atomic_helper_update_plane,
-+ .disable_plane = drm_atomic_helper_disable_plane,
-+ .destroy = vc4_plane_destroy,
-+ .set_property = NULL,
-+ .reset = drm_atomic_helper_plane_reset,
-+ .atomic_duplicate_state = drm_atomic_helper_plane_duplicate_state,
-+ .atomic_destroy_state = drm_atomic_helper_plane_destroy_state,
-+};
-+
-+static const struct drm_plane_helper_funcs vc4_primary_plane_helper_funcs = {
-+ .prepare_fb = NULL,
-+ .cleanup_fb = NULL,
-+ .atomic_check = vc4_plane_atomic_check,
-+ .atomic_update = vc4_primary_plane_atomic_update,
-+ .atomic_disable = vc4_primary_plane_atomic_disable,
-+};
-+
-+static const struct drm_plane_helper_funcs vc4_cursor_plane_helper_funcs = {
-+ .prepare_fb = NULL,
-+ .cleanup_fb = NULL,
-+ .atomic_check = vc4_plane_atomic_check,
-+ .atomic_update = vc4_cursor_plane_atomic_update,
-+ .atomic_disable = vc4_cursor_plane_atomic_disable,
-+};
-+
-+static struct drm_plane *vc4_fkms_plane_init(struct drm_device *dev,
-+ enum drm_plane_type type)
-+{
-+ struct drm_plane *plane = NULL;
-+ struct vc4_fkms_plane *vc4_plane;
-+ u32 xrgb8888 = DRM_FORMAT_XRGB8888;
-+ u32 argb8888 = DRM_FORMAT_ARGB8888;
-+ int ret = 0;
-+ bool primary = (type == DRM_PLANE_TYPE_PRIMARY);
-+
-+ vc4_plane = devm_kzalloc(dev->dev, sizeof(*vc4_plane),
-+ GFP_KERNEL);
-+ if (!vc4_plane) {
-+ ret = -ENOMEM;
-+ goto fail;
-+ }
-+
-+ plane = &vc4_plane->base;
-+ ret = drm_universal_plane_init(dev, plane, 0xff,
-+ &vc4_plane_funcs,
-+ primary ? &xrgb8888 : &argb8888, 1,
-+ type);
-+
-+ if (type == DRM_PLANE_TYPE_PRIMARY) {
-+ vc4_plane->fbinfo =
-+ dma_alloc_coherent(dev->dev,
-+ sizeof(*vc4_plane->fbinfo),
-+ &vc4_plane->fbinfo_bus_addr,
-+ GFP_KERNEL);
-+ memset(vc4_plane->fbinfo, 0, sizeof(*vc4_plane->fbinfo));
-+
-+ drm_plane_helper_add(plane, &vc4_primary_plane_helper_funcs);
-+ } else {
-+ drm_plane_helper_add(plane, &vc4_cursor_plane_helper_funcs);
-+ }
-+
-+ return plane;
-+fail:
-+ if (plane)
-+ vc4_plane_destroy(plane);
-+
-+ return ERR_PTR(ret);
-+}
-+
-+static void vc4_crtc_mode_set_nofb(struct drm_crtc *crtc)
-+{
-+ /* Everyting is handled in the planes. */
-+}
-+
-+static void vc4_crtc_disable(struct drm_crtc *crtc)
-+{
-+}
-+
-+static void vc4_crtc_enable(struct drm_crtc *crtc)
-+{
-+}
-+
-+static int vc4_crtc_atomic_check(struct drm_crtc *crtc,
-+ struct drm_crtc_state *state)
-+{
-+ return 0;
-+}
-+
-+static void vc4_crtc_atomic_flush(struct drm_crtc *crtc,
-+ struct drm_crtc_state *old_state)
-+{
-+}
-+
-+static void vc4_crtc_handle_page_flip(struct vc4_crtc *vc4_crtc)
-+{
-+ struct drm_crtc *crtc = &vc4_crtc->base;
-+ struct drm_device *dev = crtc->dev;
-+ unsigned long flags;
-+
-+ spin_lock_irqsave(&dev->event_lock, flags);
-+ if (vc4_crtc->event) {
-+ drm_crtc_send_vblank_event(crtc, vc4_crtc->event);
-+ vc4_crtc->event = NULL;
-+ drm_crtc_vblank_put(crtc);
-+ }
-+ spin_unlock_irqrestore(&dev->event_lock, flags);
-+}
-+
-+static irqreturn_t vc4_crtc_irq_handler(int irq, void *data)
-+{
-+ struct vc4_crtc *vc4_crtc = data;
-+ u32 stat = readl(vc4_crtc->regs + SMICS);
-+ irqreturn_t ret = IRQ_NONE;
-+
-+ if (stat & SMICS_INTERRUPTS) {
-+ writel(0, vc4_crtc->regs + SMICS);
-+ drm_crtc_handle_vblank(&vc4_crtc->base);
-+ vc4_crtc_handle_page_flip(vc4_crtc);
-+ ret = IRQ_HANDLED;
-+ }
-+
-+ return ret;
-+}
-+
-+static int vc4_page_flip(struct drm_crtc *crtc,
-+ struct drm_framebuffer *fb,
-+ struct drm_pending_vblank_event *event,
-+ uint32_t flags)
-+{
-+ if (flags & DRM_MODE_PAGE_FLIP_ASYNC) {
-+ DRM_ERROR("Async flips aren't allowed\n");
-+ return -EINVAL;
-+ }
-+
-+ return drm_atomic_helper_page_flip(crtc, fb, event, flags);
-+}
-+
-+static const struct drm_crtc_funcs vc4_crtc_funcs = {
-+ .set_config = drm_atomic_helper_set_config,
-+ .destroy = drm_crtc_cleanup,
-+ .page_flip = vc4_page_flip,
-+ .set_property = NULL,
-+ .cursor_set = NULL, /* handled by drm_mode_cursor_universal */
-+ .cursor_move = NULL, /* handled by drm_mode_cursor_universal */
-+ .reset = drm_atomic_helper_crtc_reset,
-+ .atomic_duplicate_state = drm_atomic_helper_crtc_duplicate_state,
-+ .atomic_destroy_state = drm_atomic_helper_crtc_destroy_state,
-+};
-+
-+static const struct drm_crtc_helper_funcs vc4_crtc_helper_funcs = {
-+ .mode_set_nofb = vc4_crtc_mode_set_nofb,
-+ .disable = vc4_crtc_disable,
-+ .enable = vc4_crtc_enable,
-+ .atomic_check = vc4_crtc_atomic_check,
-+ .atomic_flush = vc4_crtc_atomic_flush,
-+};
-+
-+/* Frees the page flip event when the DRM device is closed with the
-+ * event still outstanding.
-+ */
-+void vc4_fkms_cancel_page_flip(struct drm_crtc *crtc, struct drm_file *file)
-+{
-+ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
-+ struct drm_device *dev = crtc->dev;
-+ unsigned long flags;
-+
-+ spin_lock_irqsave(&dev->event_lock, flags);
-+
-+ if (vc4_crtc->event && vc4_crtc->event->base.file_priv == file) {
-+ vc4_crtc->event->base.destroy(&vc4_crtc->event->base);
-+ drm_crtc_vblank_put(crtc);
-+ vc4_crtc->event = NULL;
-+ }
-+
-+ spin_unlock_irqrestore(&dev->event_lock, flags);
-+}
-+
-+static const struct of_device_id vc4_firmware_kms_dt_match[] = {
-+ { .compatible = "raspberrypi,rpi-firmware-kms" },
-+ {}
-+};
-+
-+static enum drm_connector_status
-+vc4_fkms_connector_detect(struct drm_connector *connector, bool force)
-+{
-+ return connector_status_connected;
-+}
-+
-+static int vc4_fkms_connector_get_modes(struct drm_connector *connector)
-+{
-+ struct drm_device *dev = connector->dev;
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ u32 wh[2] = {0, 0};
-+ int ret;
-+ struct drm_display_mode *mode;
-+
-+ ret = rpi_firmware_property(vc4->firmware,
-+ RPI_FIRMWARE_FRAMEBUFFER_GET_PHYSICAL_WIDTH_HEIGHT,
-+ &wh, sizeof(wh));
-+ if (ret) {
-+ DRM_ERROR("Failed to get screen size: %d (0x%08x 0x%08x)\n",
-+ ret, wh[0], wh[1]);
-+ return 0;
-+ }
-+
-+ mode = drm_cvt_mode(dev, wh[0], wh[1], 60 /* vrefresh */,
-+ 0, 0, false);
-+ drm_mode_probed_add(connector, mode);
-+
-+ return 1;
-+}
-+
-+static struct drm_encoder *
-+vc4_fkms_connector_best_encoder(struct drm_connector *connector)
-+{
-+ struct vc4_fkms_connector *fkms_connector =
-+ to_vc4_fkms_connector(connector);
-+ return fkms_connector->encoder;
-+}
-+
-+static void vc4_fkms_connector_destroy(struct drm_connector *connector)
-+{
-+ drm_connector_unregister(connector);
-+ drm_connector_cleanup(connector);
-+}
-+
-+static const struct drm_connector_funcs vc4_fkms_connector_funcs = {
-+ .dpms = drm_atomic_helper_connector_dpms,
-+ .detect = vc4_fkms_connector_detect,
-+ .fill_modes = drm_helper_probe_single_connector_modes,
-+ .destroy = vc4_fkms_connector_destroy,
-+ .reset = drm_atomic_helper_connector_reset,
-+ .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
-+ .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
-+};
-+
-+static const struct drm_connector_helper_funcs vc4_fkms_connector_helper_funcs = {
-+ .get_modes = vc4_fkms_connector_get_modes,
-+ .best_encoder = vc4_fkms_connector_best_encoder,
-+};
-+
-+static struct drm_connector *vc4_fkms_connector_init(struct drm_device *dev,
-+ struct drm_encoder *encoder)
-+{
-+ struct drm_connector *connector = NULL;
-+ struct vc4_fkms_connector *fkms_connector;
-+ int ret = 0;
-+
-+ fkms_connector = devm_kzalloc(dev->dev, sizeof(*fkms_connector),
-+ GFP_KERNEL);
-+ if (!fkms_connector) {
-+ ret = -ENOMEM;
-+ goto fail;
-+ }
-+ connector = &fkms_connector->base;
-+
-+ fkms_connector->encoder = encoder;
-+
-+ drm_connector_init(dev, connector, &vc4_fkms_connector_funcs,
-+ DRM_MODE_CONNECTOR_HDMIA);
-+ drm_connector_helper_add(connector, &vc4_fkms_connector_helper_funcs);
-+
-+ connector->polled = (DRM_CONNECTOR_POLL_CONNECT |
-+ DRM_CONNECTOR_POLL_DISCONNECT);
-+
-+ connector->interlace_allowed = 0;
-+ connector->doublescan_allowed = 0;
-+
-+ drm_mode_connector_attach_encoder(connector, encoder);
-+
-+ return connector;
-+
-+ fail:
-+ if (connector)
-+ vc4_fkms_connector_destroy(connector);
-+
-+ return ERR_PTR(ret);
-+}
-+
-+static void vc4_fkms_encoder_destroy(struct drm_encoder *encoder)
-+{
-+ drm_encoder_cleanup(encoder);
-+}
-+
-+static const struct drm_encoder_funcs vc4_fkms_encoder_funcs = {
-+ .destroy = vc4_fkms_encoder_destroy,
-+};
-+
-+static void vc4_fkms_encoder_enable(struct drm_encoder *encoder)
-+{
-+}
-+
-+static void vc4_fkms_encoder_disable(struct drm_encoder *encoder)
-+{
-+}
-+
-+static const struct drm_encoder_helper_funcs vc4_fkms_encoder_helper_funcs = {
-+ .enable = vc4_fkms_encoder_enable,
-+ .disable = vc4_fkms_encoder_disable,
-+};
-+
-+static int vc4_fkms_bind(struct device *dev, struct device *master, void *data)
-+{
-+ struct platform_device *pdev = to_platform_device(dev);
-+ struct drm_device *drm = dev_get_drvdata(master);
-+ struct vc4_dev *vc4 = to_vc4_dev(drm);
-+ struct vc4_crtc *vc4_crtc;
-+ struct vc4_fkms_encoder *vc4_encoder;
-+ struct drm_crtc *crtc;
-+ struct drm_plane *primary_plane, *cursor_plane, *destroy_plane, *temp;
-+ struct device_node *firmware_node;
-+ int ret;
-+
-+ vc4->firmware_kms = true;
-+
-+ vc4_crtc = devm_kzalloc(dev, sizeof(*vc4_crtc), GFP_KERNEL);
-+ if (!vc4_crtc)
-+ return -ENOMEM;
-+ crtc = &vc4_crtc->base;
-+
-+ firmware_node = of_parse_phandle(dev->of_node, "brcm,firmware", 0);
-+ vc4->firmware = rpi_firmware_get(firmware_node);
-+ if (!vc4->firmware) {
-+ DRM_DEBUG("Failed to get Raspberry Pi firmware reference.\n");
-+ return -EPROBE_DEFER;
-+ }
-+ of_node_put(firmware_node);
-+
-+ /* Map the SMI interrupt reg */
-+ vc4_crtc->regs = vc4_ioremap_regs(pdev, 0);
-+ if (IS_ERR(vc4_crtc->regs))
-+ return PTR_ERR(vc4_crtc->regs);
-+
-+ /* For now, we create just the primary and the legacy cursor
-+ * planes. We should be able to stack more planes on easily,
-+ * but to do that we would need to compute the bandwidth
-+ * requirement of the plane configuration, and reject ones
-+ * that will take too much.
-+ */
-+ primary_plane = vc4_fkms_plane_init(drm, DRM_PLANE_TYPE_PRIMARY);
-+ if (IS_ERR(primary_plane)) {
-+ dev_err(dev, "failed to construct primary plane\n");
-+ ret = PTR_ERR(primary_plane);
-+ goto err;
-+ }
-+
-+ cursor_plane = vc4_fkms_plane_init(drm, DRM_PLANE_TYPE_CURSOR);
-+ if (IS_ERR(cursor_plane)) {
-+ dev_err(dev, "failed to construct cursor plane\n");
-+ ret = PTR_ERR(cursor_plane);
-+ goto err;
-+ }
-+
-+ drm_crtc_init_with_planes(drm, crtc, primary_plane, cursor_plane,
-+ &vc4_crtc_funcs);
-+ drm_crtc_helper_add(crtc, &vc4_crtc_helper_funcs);
-+ primary_plane->crtc = crtc;
-+ cursor_plane->crtc = crtc;
-+ vc4->crtc[drm_crtc_index(crtc)] = vc4_crtc;
-+
-+ vc4_encoder = devm_kzalloc(dev, sizeof(*vc4_encoder), GFP_KERNEL);
-+ if (!vc4_encoder)
-+ return -ENOMEM;
-+ vc4_crtc->encoder = &vc4_encoder->base;
-+ vc4_encoder->base.possible_crtcs |= drm_crtc_mask(crtc) ;
-+ drm_encoder_init(drm, &vc4_encoder->base, &vc4_fkms_encoder_funcs,
-+ DRM_MODE_ENCODER_TMDS);
-+ drm_encoder_helper_add(&vc4_encoder->base,
-+ &vc4_fkms_encoder_helper_funcs);
-+
-+ vc4_crtc->connector = vc4_fkms_connector_init(drm, &vc4_encoder->base);
-+ if (IS_ERR(vc4_crtc->connector)) {
-+ ret = PTR_ERR(vc4_crtc->connector);
-+ goto err_destroy_encoder;
-+ }
-+
-+ writel(0, vc4_crtc->regs + SMICS);
-+ ret = devm_request_irq(dev, platform_get_irq(pdev, 0),
-+ vc4_crtc_irq_handler, 0, "vc4 firmware kms",
-+ vc4_crtc);
-+ if (ret)
-+ goto err_destroy_connector;
-+
-+ platform_set_drvdata(pdev, vc4_crtc);
-+
-+ return 0;
-+
-+err_destroy_connector:
-+ vc4_fkms_connector_destroy(vc4_crtc->connector);
-+err_destroy_encoder:
-+ vc4_fkms_encoder_destroy(vc4_crtc->encoder);
-+ list_for_each_entry_safe(destroy_plane, temp,
-+ &drm->mode_config.plane_list, head) {
-+ if (destroy_plane->possible_crtcs == 1 << drm_crtc_index(crtc))
-+ destroy_plane->funcs->destroy(destroy_plane);
-+ }
-+err:
-+ return ret;
-+}
-+
-+static void vc4_fkms_unbind(struct device *dev, struct device *master,
-+ void *data)
-+{
-+ struct platform_device *pdev = to_platform_device(dev);
-+ struct vc4_crtc *vc4_crtc = dev_get_drvdata(dev);
-+
-+ vc4_fkms_connector_destroy(vc4_crtc->connector);
-+ vc4_fkms_encoder_destroy(vc4_crtc->encoder);
-+ drm_crtc_cleanup(&vc4_crtc->base);
-+
-+ platform_set_drvdata(pdev, NULL);
-+}
-+
-+static const struct component_ops vc4_fkms_ops = {
-+ .bind = vc4_fkms_bind,
-+ .unbind = vc4_fkms_unbind,
-+};
-+
-+static int vc4_fkms_probe(struct platform_device *pdev)
-+{
-+ return component_add(&pdev->dev, &vc4_fkms_ops);
-+}
-+
-+static int vc4_fkms_remove(struct platform_device *pdev)
-+{
-+ component_del(&pdev->dev, &vc4_fkms_ops);
-+ return 0;
-+}
-+
-+struct platform_driver vc4_firmware_kms_driver = {
-+ .probe = vc4_fkms_probe,
-+ .remove = vc4_fkms_remove,
-+ .driver = {
-+ .name = "vc4_firmware_kms",
-+ .of_match_table = vc4_firmware_kms_dt_match,
-+ },
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0506-BCM270X-Add-an-overlay-for-enabling-the-vc4-driver-i.patch b/target/linux/brcm2708/patches-4.4/0506-BCM270X-Add-an-overlay-for-enabling-the-vc4-driver-i.patch
deleted file mode 100644
index 3d48b40..0000000
--- a/target/linux/brcm2708/patches-4.4/0506-BCM270X-Add-an-overlay-for-enabling-the-vc4-driver-i.patch
+++ /dev/null
@@ -1,189 +0,0 @@
-From 74759d90a1556cac03225046a976805fd3585f8d Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Wed, 14 Sep 2016 08:52:26 +0100
-Subject: [PATCH] BCM270X: Add an overlay for enabling the vc4 driver in
- firmware-KMS mode.
-
-This gets us normal 3D support on top of the existing firmware display
-stack. There's no real modesetting support, no async pageflips
-(hurting performance), etc., but it means that the desktop can at
-least run until we get full native modesetting.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- arch/arm/boot/dts/bcm2708_common.dtsi | 31 +++++---
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 11 +++
- .../arm/boot/dts/overlays/vc4-fkms-v3d-overlay.dts | 89 ++++++++++++++++++++++
- 4 files changed, 121 insertions(+), 11 deletions(-)
- create mode 100644 arch/arm/boot/dts/overlays/vc4-fkms-v3d-overlay.dts
-
---- a/arch/arm/boot/dts/bcm2708_common.dtsi
-+++ b/arch/arm/boot/dts/bcm2708_common.dtsi
-@@ -284,6 +284,26 @@
- status = "disabled";
- };
-
-+ firmwarekms: firmwarekms at 7e600000 {
-+ compatible = "raspberrypi,rpi-firmware-kms";
-+ /* SMI interrupt reg */
-+ reg = <0x7e600000 0x100>;
-+ interrupts = <2 16>;
-+ brcm,firmware = <&firmware>;
-+ status = "disabled";
-+ };
-+
-+ smi: smi at 7e600000 {
-+ compatible = "brcm,bcm2835-smi";
-+ reg = <0x7e600000 0x44>, <0x7e1010b0 0x8>;
-+ interrupts = <2 16>;
-+ brcm,smi-clock-source = <6>;
-+ brcm,smi-clock-divisor = <4>;
-+ dmas = <&dma 4>;
-+ dma-names = "rx-tx";
-+ status = "disabled";
-+ };
-+
- dsi1: dsi at 7e700000 {
- #address-cells = <1>;
- #size-cells = <0>;
-@@ -325,17 +345,6 @@
- status = "disabled";
- };
-
-- smi: smi at 7e600000 {
-- compatible = "brcm,bcm2835-smi";
-- reg = <0x7e600000 0x44>, <0x7e1010b0 0x8>;
-- interrupts = <2 16>;
-- brcm,smi-clock-source = <6>;
-- brcm,smi-clock-divisor = <4>;
-- dmas = <&dma 4>;
-- dma-names = "rx-tx";
-- status = "disabled";
-- };
--
- pixelvalve2: pixelvalve at 7e807000 {
- compatible = "brcm,bcm2835-pixelvalve2";
- reg = <0x7e807000 0x100>;
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -96,6 +96,7 @@ dtbo-$(RPI_DT_OVERLAYS) += spi2-2cs.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += spi2-3cs.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += tinylcd35.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += uart1.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += vc4-fkms-v3d.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += vc4-kms-v3d.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += vga666.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += w1-gpio.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -1215,6 +1215,17 @@ Params: txd1_pin GPIO pin
- rxd1_pin GPIO pin for RXD1 (15, 33 or 41 - default 15)
-
-
-+Name: vc4-fkms-v3d
-+Info: Enable Eric Anholt's DRM VC4 V3D driver on top of the dispmanx
-+ display stack.
-+Load: dtoverlay=vc4-fkms-v3d,<param>
-+Params: cma-256 CMA is 256MB, 256MB-aligned (needs 1GB)
-+ cma-192 CMA is 192MB, 256MB-aligned (needs 1GB)
-+ cma-128 CMA is 128MB, 128MB-aligned
-+ cma-96 CMA is 96MB, 128MB-aligned
-+ cma-64 CMA is 64MB, 64MB-aligned
-+
-+
- Name: vc4-kms-v3d
- Info: Enable Eric Anholt's DRM VC4 HDMI/HVS/V3D driver. Running startx or
- booting to GUI while this overlay is in use will cause interesting
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/vc4-fkms-v3d-overlay.dts
-@@ -0,0 +1,89 @@
-+/*
-+ * vc4-fkms-v3d-overlay.dts
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target-path = "/chosen";
-+ __overlay__ {
-+ bootargs = "cma=256M at 256M";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target-path = "/chosen";
-+ __dormant__ {
-+ bootargs = "cma=192M at 256M";
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target-path = "/chosen";
-+ __dormant__ {
-+ bootargs = "cma=128M at 128M";
-+ };
-+ };
-+
-+ fragment at 3 {
-+ target-path = "/chosen";
-+ __dormant__ {
-+ bootargs = "cma=96M at 128M";
-+ };
-+ };
-+
-+ fragment at 4 {
-+ target-path = "/chosen";
-+ __dormant__ {
-+ bootargs = "cma=64M at 64M";
-+ };
-+ };
-+
-+ fragment at 5 {
-+ target = <&fb>;
-+ __overlay__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ fragment at 6 {
-+ target = <&firmwarekms>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 7 {
-+ target = <&v3d>;
-+ __overlay__ {
-+ interrupts = <1 10>;
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 8 {
-+ target = <&gpu>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 9 {
-+ target-path = "/soc/dma";
-+ __overlay__ {
-+ brcm,dma-channel-mask = <0x7f35>;
-+ };
-+ };
-+
-+ __overrides__ {
-+ cma-256 = <0>,"+0-1-2-3-4";
-+ cma-192 = <0>,"-0+1-2-3-4";
-+ cma-128 = <0>,"-0-1+2-3-4";
-+ cma-96 = <0>,"-0-1-2+3-4";
-+ cma-64 = <0>,"-0-1-2-3+4";
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0507-Allo-Piano-DAC-boards-Initial-2-channel-stereo-suppo.patch b/target/linux/brcm2708/patches-4.4/0507-Allo-Piano-DAC-boards-Initial-2-channel-stereo-suppo.patch
deleted file mode 100644
index c0cdba9..0000000
--- a/target/linux/brcm2708/patches-4.4/0507-Allo-Piano-DAC-boards-Initial-2-channel-stereo-suppo.patch
+++ /dev/null
@@ -1,324 +0,0 @@
-From 22283a63ebaa5d81f228a7d76290da508c6ecc09 Mon Sep 17 00:00:00 2001
-From: Clive Messer <clive.m.messer at gmail.com>
-Date: Mon, 19 Sep 2016 14:01:04 +0100
-Subject: [PATCH] Allo Piano DAC boards: Initial 2 channel (stereo) support
- (#1645)
-
-Add initial 2 channel (stereo) support for Allo Piano DAC (2.0/2.1) boards,
-using allo-piano-dac-pcm512x-audio overlay and allo-piano-dac ALSA ASoC
-machine driver.
-
-NB. The initial support is 2 channel (stereo) ONLY!
-(The Piano DAC 2.1 will only support 2 channel (stereo) left/right output,
- pending an update to the upstream pcm512x codec driver, which will have
- to be submitted via upstream. With the initial downstream support,
- provided by this patch, the Piano DAC 2.1 subwoofer outputs will
- not function.)
-
-Signed-off-by: Baswaraj K <jaikumar at cem-solutions.net>
-Signed-off-by: Clive Messer <clive.messer at digitaldreamtime.co.uk>
-Tested-by: Clive Messer <clive.messer at digitaldreamtime.co.uk>
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 20 +++
- .../allo-piano-dac-pcm512x-audio-overlay.dts | 54 ++++++++
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- sound/soc/bcm/Kconfig | 7 +
- sound/soc/bcm/Makefile | 2 +
- sound/soc/bcm/allo-piano-dac.c | 144 +++++++++++++++++++++
- 8 files changed, 230 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/allo-piano-dac-pcm512x-audio-overlay.dts
- create mode 100644 sound/soc/bcm/allo-piano-dac.c
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -16,6 +16,7 @@ dtbo-$(RPI_DT_OVERLAYS) += adau1977-adc.
- dtbo-$(RPI_DT_OVERLAYS) += ads1015.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += ads7846.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += akkordion-iqdacplus.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += allo-piano-dac-pcm512x-audio.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += at86rf233.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += audioinjector-wm8731-audio.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += audremap.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -235,6 +235,26 @@ Params: 24db_digital_gain Allow ga
- that does not result in clipping/distortion!)
-
-
-+Name: allo-piano-dac-pcm512x-audio
-+Info: Configures the Allo Piano DAC (2.0/2.1) audio cards.
-+ (NB. This initial support is for 2.0 channel audio ONLY! ie. stereo.
-+ The subwoofer outputs on the Piano 2.1 are not currently supported!)
-+Load: dtoverlay=allo-piano-dac-pcm512x-audio,<param>
-+Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec
-+ Digital volume control.
-+ (The default behaviour is that the Digital
-+ volume control is limited to a maximum of
-+ 0dB. ie. it can attenuate but not provide
-+ gain. For most users, this will be desired
-+ as it will prevent clipping. By appending
-+ the 24db_digital_gain parameter, the Digital
-+ volume control will allow up to 24dB of
-+ gain. If this parameter is enabled, it is the
-+ responsibility of the user to ensure that
-+ the Digital volume control is set to a value
-+ that does not result in clipping/distortion!)
-+
-+
- Name: at86rf233
- Info: Configures the Atmel AT86RF233 802.15.4 low-power WPAN transceiver,
- connected to spi0.0
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/allo-piano-dac-pcm512x-audio-overlay.dts
-@@ -0,0 +1,54 @@
-+/*
-+ * Definitions for Allo Piano DAC (2.0/2.1) boards
-+ *
-+ * NB. The Piano DAC 2.1 board contains 2x TI PCM5142 DAC's. One DAC is stereo
-+ * (left/right) and the other provides a subwoofer output, using DSP on the
-+ * chip for digital high/low pass crossover.
-+ * The initial support for this hardware, that doesn't require any codec driver
-+ * modifications, uses only one DAC chip for stereo (left/right) output, the
-+ * chip with 0x4c slave address. The other chip at 0x4d is currently ignored!
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&i2s>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&i2c1>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ pcm5142 at 4c {
-+ #sound-dai-cells = <0>;
-+ compatible = "ti,pcm5142";
-+ reg = <0x4c>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&sound>;
-+ piano_dac: __overlay__ {
-+ compatible = "allo,piano-dac";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+ };
-+ };
-+
-+ __overrides__ {
-+ 24db_digital_gain =
-+ <&piano_dac>,"allo,24db_digital_gain?";
-+ };
-+};
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -879,6 +879,7 @@ CONFIG_SND_BCM2708_SOC_ADAU1977_ADC=m
- CONFIG_SND_AUDIOINJECTOR_PI_SOUNDCARD=m
- CONFIG_SND_DIGIDAC1_SOUNDCARD=m
- CONFIG_SND_BCM2708_SOC_DIONAUDIO_LOCO=m
-+CONFIG_SND_BCM2708_SOC_ALLO_PIANO_DAC=m
- CONFIG_SND_SOC_ADAU1701=m
- CONFIG_SND_SOC_WM8804_I2C=m
- CONFIG_SND_SIMPLE_CARD=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -871,6 +871,7 @@ CONFIG_SND_BCM2708_SOC_ADAU1977_ADC=m
- CONFIG_SND_AUDIOINJECTOR_PI_SOUNDCARD=m
- CONFIG_SND_DIGIDAC1_SOUNDCARD=m
- CONFIG_SND_BCM2708_SOC_DIONAUDIO_LOCO=m
-+CONFIG_SND_BCM2708_SOC_ALLO_PIANO_DAC=m
- CONFIG_SND_SOC_ADAU1701=m
- CONFIG_SND_SOC_WM8804_I2C=m
- CONFIG_SND_SIMPLE_CARD=m
---- a/sound/soc/bcm/Kconfig
-+++ b/sound/soc/bcm/Kconfig
-@@ -114,3 +114,10 @@ config SND_BCM2708_SOC_DIONAUDIO_LOCO
- select SND_SOC_PCM5102a
- help
- Say Y or M if you want to add support for Dion Audio LOCO.
-+
-+config SND_BCM2708_SOC_ALLO_PIANO_DAC
-+ tristate "Support for Allo Piano DAC"
-+ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
-+ select SND_SOC_PCM512x_I2C
-+ help
-+ Say Y or M if you want to add support for Allo Piano DAC.
---- a/sound/soc/bcm/Makefile
-+++ b/sound/soc/bcm/Makefile
-@@ -19,6 +19,7 @@ snd-soc-raspidac3-objs := raspidac3.o
- snd-soc-audioinjector-pi-soundcard-objs := audioinjector-pi-soundcard.o
- snd-soc-digidac1-soundcard-objs := digidac1-soundcard.o
- snd-soc-dionaudio-loco-objs := dionaudio_loco.o
-+snd-soc-allo-piano-dac-objs := allo-piano-dac.o
-
- obj-$(CONFIG_SND_BCM2708_SOC_ADAU1977_ADC) += snd-soc-adau1977-adc.o
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DAC) += snd-soc-hifiberry-dac.o
-@@ -35,3 +36,4 @@ obj-$(CONFIG_SND_BCM2708_SOC_RASPIDAC3)
- obj-$(CONFIG_SND_AUDIOINJECTOR_PI_SOUNDCARD) += snd-soc-audioinjector-pi-soundcard.o
- obj-$(CONFIG_SND_DIGIDAC1_SOUNDCARD) += snd-soc-digidac1-soundcard.o
- obj-$(CONFIG_SND_BCM2708_SOC_DIONAUDIO_LOCO) += snd-soc-dionaudio-loco.o
-+obj-$(CONFIG_SND_BCM2708_SOC_ALLO_PIANO_DAC) += snd-soc-allo-piano-dac.o
---- /dev/null
-+++ b/sound/soc/bcm/allo-piano-dac.c
-@@ -0,0 +1,144 @@
-+/*
-+ * ALSA ASoC Machine Driver for Allo Piano DAC
-+ *
-+ * Author: Baswaraj K <jaikumar at cem-solutions.net>
-+ * Copyright 2016
-+ * based on code by Daniel Matuschek <info at crazy-audio.com>
-+ * based on code by Florian Meier <florian.meier at koalo.de>
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * version 2 as published by the Free Software Foundation.
-+ *
-+ * This program is distributed in the hope that it will be useful, but
-+ * WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
-+ * General Public License for more details.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+
-+#include <sound/core.h>
-+#include <sound/pcm.h>
-+#include <sound/pcm_params.h>
-+#include <sound/soc.h>
-+
-+static bool digital_gain_0db_limit = true;
-+
-+static int snd_allo_piano_dac_init(struct snd_soc_pcm_runtime *rtd)
-+{
-+ if (digital_gain_0db_limit) {
-+ int ret;
-+ struct snd_soc_card *card = rtd->card;
-+
-+ ret = snd_soc_limit_volume(card, "Digital Playback Volume",
-+ 207);
-+ if (ret < 0)
-+ dev_warn(card->dev, "Failed to set volume limit: %d\n",
-+ ret);
-+ }
-+
-+ return 0;
-+}
-+
-+static int snd_allo_piano_dac_hw_params(
-+ struct snd_pcm_substream *substream, struct snd_pcm_hw_params *params)
-+{
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
-+
-+ unsigned int sample_bits =
-+ snd_pcm_format_physical_width(params_format(params));
-+
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, sample_bits * 2);
-+}
-+
-+/* machine stream operations */
-+static struct snd_soc_ops snd_allo_piano_dac_ops = {
-+ .hw_params = snd_allo_piano_dac_hw_params,
-+};
-+
-+static struct snd_soc_dai_link snd_allo_piano_dac_dai[] = {
-+{
-+ .name = "Piano DAC",
-+ .stream_name = "Piano DAC HiFi",
-+ .cpu_dai_name = "bcm2708-i2s.0",
-+ .codec_dai_name = "pcm512x-hifi",
-+ .platform_name = "bcm2708-i2s.0",
-+ .codec_name = "pcm512x.1-004c",
-+ .dai_fmt = SND_SOC_DAIFMT_I2S |
-+ SND_SOC_DAIFMT_NB_NF |
-+ SND_SOC_DAIFMT_CBS_CFS,
-+ .ops = &snd_allo_piano_dac_ops,
-+ .init = snd_allo_piano_dac_init,
-+},
-+};
-+
-+/* audio machine driver */
-+static struct snd_soc_card snd_allo_piano_dac = {
-+ .name = "PianoDAC",
-+ .owner = THIS_MODULE,
-+ .dai_link = snd_allo_piano_dac_dai,
-+ .num_links = ARRAY_SIZE(snd_allo_piano_dac_dai),
-+};
-+
-+static int snd_allo_piano_dac_probe(struct platform_device *pdev)
-+{
-+ int ret = 0;
-+
-+ snd_allo_piano_dac.dev = &pdev->dev;
-+
-+ if (pdev->dev.of_node) {
-+ struct device_node *i2s_node;
-+ struct snd_soc_dai_link *dai;
-+
-+ dai = &snd_allo_piano_dac_dai[0];
-+ i2s_node = of_parse_phandle(pdev->dev.of_node,
-+ "i2s-controller", 0);
-+
-+ if (i2s_node) {
-+ dai->cpu_dai_name = NULL;
-+ dai->cpu_of_node = i2s_node;
-+ dai->platform_name = NULL;
-+ dai->platform_of_node = i2s_node;
-+ }
-+
-+ digital_gain_0db_limit = !of_property_read_bool(
-+ pdev->dev.of_node, "allo,24db_digital_gain");
-+ }
-+
-+ ret = snd_soc_register_card(&snd_allo_piano_dac);
-+ if (ret)
-+ dev_err(&pdev->dev,
-+ "snd_soc_register_card() failed: %d\n", ret);
-+
-+ return ret;
-+}
-+
-+static int snd_allo_piano_dac_remove(struct platform_device *pdev)
-+{
-+ return snd_soc_unregister_card(&snd_allo_piano_dac);
-+}
-+
-+static const struct of_device_id snd_allo_piano_dac_of_match[] = {
-+ { .compatible = "allo,piano-dac", },
-+ { /* sentinel */ },
-+};
-+MODULE_DEVICE_TABLE(of, snd_allo_piano_dac_of_match);
-+
-+static struct platform_driver snd_allo_piano_dac_driver = {
-+ .driver = {
-+ .name = "snd-allo-piano-dac",
-+ .owner = THIS_MODULE,
-+ .of_match_table = snd_allo_piano_dac_of_match,
-+ },
-+ .probe = snd_allo_piano_dac_probe,
-+ .remove = snd_allo_piano_dac_remove,
-+};
-+
-+module_platform_driver(snd_allo_piano_dac_driver);
-+
-+MODULE_AUTHOR("Baswaraj K <jaikumar at cem-solutions.net>");
-+MODULE_DESCRIPTION("ALSA ASoC Machine Driver for Allo Piano DAC");
-+MODULE_LICENSE("GPL v2");
diff --git a/target/linux/brcm2708/patches-4.4/0508-Correct-typos-in-spi-gpio35-39-overlay.dts-1651.patch b/target/linux/brcm2708/patches-4.4/0508-Correct-typos-in-spi-gpio35-39-overlay.dts-1651.patch
deleted file mode 100644
index 839416b..0000000
--- a/target/linux/brcm2708/patches-4.4/0508-Correct-typos-in-spi-gpio35-39-overlay.dts-1651.patch
+++ /dev/null
@@ -1,29 +0,0 @@
-From d30b600bd635d4e1f585b8e491899681a9b23352 Mon Sep 17 00:00:00 2001
-From: Blogs14 <masterwhite445 at googlemail.com>
-Date: Fri, 23 Sep 2016 11:02:56 +0100
-Subject: [PATCH] Correct typos in spi-gpio35-39-overlay.dts (#1651)
-
-bcrm,pins corrected to brcm,pins
----
- arch/arm/boot/dts/overlays/spi-gpio35-39-overlay.dts | 4 ++--
- 1 file changed, 2 insertions(+), 2 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/spi-gpio35-39-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/spi-gpio35-39-overlay.dts
-@@ -18,14 +18,14 @@
- fragment at 1 {
- target = <&spi0_cs_pins>;
- __overlay__ {
-- bcrm,pins = <36 35>;
-+ brcm,pins = <36 35>;
- };
- };
-
- fragment at 2 {
- target = <&spi0_pins>;
- __overlay__ {
-- bcrm,pins = <37 38 39>;
-+ brcm,pins = <37 38 39>;
- };
- };
- };
diff --git a/target/linux/brcm2708/patches-4.4/0510-drm-vc4-Enable-limited-range-RGB-output-with-CEA-mod.patch b/target/linux/brcm2708/patches-4.4/0510-drm-vc4-Enable-limited-range-RGB-output-with-CEA-mod.patch
deleted file mode 100644
index ae79ae1..0000000
--- a/target/linux/brcm2708/patches-4.4/0510-drm-vc4-Enable-limited-range-RGB-output-with-CEA-mod.patch
+++ /dev/null
@@ -1,83 +0,0 @@
-From 9742e47dadf727e71b8bb75080ec24acd7cd2b96 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Thu, 15 Sep 2016 17:52:17 +0100
-Subject: [PATCH] drm/vc4: Enable limited range RGB output with CEA modes.
-
----
- drivers/gpu/drm/vc4/vc4_hdmi.c | 28 ++++++++++++++++++++++++++--
- drivers/gpu/drm/vc4/vc4_regs.h | 9 ++++++++-
- 2 files changed, 34 insertions(+), 3 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_hdmi.c
-+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
-@@ -285,6 +285,7 @@ static void vc4_hdmi_encoder_mode_set(st
- struct drm_display_mode *unadjusted_mode,
- struct drm_display_mode *mode)
- {
-+ struct vc4_hdmi_encoder *vc4_encoder = to_vc4_hdmi_encoder(encoder);
- struct drm_device *dev = encoder->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- bool debug_dump_regs = false;
-@@ -300,6 +301,7 @@ static void vc4_hdmi_encoder_mode_set(st
- u32 vertb = (VC4_SET_FIELD(0, VC4_HDMI_VERTB_VSPO) |
- VC4_SET_FIELD(mode->vtotal - mode->vsync_end,
- VC4_HDMI_VERTB_VBP));
-+ u32 csc_ctl;
-
- if (debug_dump_regs) {
- DRM_INFO("HDMI regs before:\n");
-@@ -338,9 +340,31 @@ static void vc4_hdmi_encoder_mode_set(st
- (vsync_pos ? 0 : VC4_HD_VID_CTL_VSYNC_LOW) |
- (hsync_pos ? 0 : VC4_HD_VID_CTL_HSYNC_LOW));
-
-+ csc_ctl = VC4_SET_FIELD(VC4_HD_CSC_CTL_ORDER_BGR,
-+ VC4_HD_CSC_CTL_ORDER);
-+
-+ if (vc4_encoder->hdmi_monitor && drm_match_cea_mode(mode) != 0) {
-+ /* Enable limited range RGB output. This matrix is:
-+ * [ 0 0 0.8594 16]
-+ * [ 0 0.8594 0 16]
-+ * [ 0.8594 0 0 16]
-+ * [ 0 0 0 1]
-+ */
-+ csc_ctl |= VC4_HD_CSC_CTL_ENABLE;
-+ csc_ctl |= VC4_HD_CSC_CTL_RGB2YCC;
-+ csc_ctl |= VC4_SET_FIELD(VC4_HD_CSC_CTL_MODE_CUSTOM,
-+ VC4_HD_CSC_CTL_MODE);
-+
-+ HD_WRITE(VC4_HD_CSC_12_11, (0x000 << 16) | 0x000);
-+ HD_WRITE(VC4_HD_CSC_14_13, (0x100 << 16) | 0x6e0);
-+ HD_WRITE(VC4_HD_CSC_22_21, (0x6e0 << 16) | 0x000);
-+ HD_WRITE(VC4_HD_CSC_24_23, (0x100 << 16) | 0x000);
-+ HD_WRITE(VC4_HD_CSC_32_31, (0x000 << 16) | 0x6e0);
-+ HD_WRITE(VC4_HD_CSC_34_33, (0x100 << 16) | 0x000);
-+ }
-+
- /* The RGB order applies even when CSC is disabled. */
-- HD_WRITE(VC4_HD_CSC_CTL, VC4_SET_FIELD(VC4_HD_CSC_CTL_ORDER_BGR,
-- VC4_HD_CSC_CTL_ORDER));
-+ HD_WRITE(VC4_HD_CSC_CTL, csc_ctl);
-
- HDMI_WRITE(VC4_HDMI_FIFO_CTL, VC4_HDMI_FIFO_CTL_MASTER_SLAVE_N);
-
---- a/drivers/gpu/drm/vc4/vc4_regs.h
-+++ b/drivers/gpu/drm/vc4/vc4_regs.h
-@@ -530,10 +530,17 @@
- # define VC4_HD_CSC_CTL_MODE_SHIFT 2
- # define VC4_HD_CSC_CTL_MODE_RGB_TO_SD_YPRPB 0
- # define VC4_HD_CSC_CTL_MODE_RGB_TO_HD_YPRPB 1
--# define VC4_HD_CSC_CTL_MODE_CUSTOM 2
-+# define VC4_HD_CSC_CTL_MODE_CUSTOM 3
- # define VC4_HD_CSC_CTL_RGB2YCC BIT(1)
- # define VC4_HD_CSC_CTL_ENABLE BIT(0)
-
-+#define VC4_HD_CSC_12_11 0x044
-+#define VC4_HD_CSC_14_13 0x048
-+#define VC4_HD_CSC_22_21 0x04c
-+#define VC4_HD_CSC_24_23 0x050
-+#define VC4_HD_CSC_32_31 0x054
-+#define VC4_HD_CSC_34_33 0x058
-+
- #define VC4_HD_FRAME_COUNT 0x068
-
- /* HVS display list information. */
diff --git a/target/linux/brcm2708/patches-4.4/0511-Add-Adafruit-pitft35-touchscreen-support-1657.patch b/target/linux/brcm2708/patches-4.4/0511-Add-Adafruit-pitft35-touchscreen-support-1657.patch
deleted file mode 100644
index 9b8806d..0000000
--- a/target/linux/brcm2708/patches-4.4/0511-Add-Adafruit-pitft35-touchscreen-support-1657.patch
+++ /dev/null
@@ -1,196 +0,0 @@
-From a0cc0a16b17996107a6dd712de9031a7bb7d0b34 Mon Sep 17 00:00:00 2001
-From: Scott Ellis <scott at jumpnowtek.com>
-Date: Tue, 27 Sep 2016 04:29:00 -0400
-Subject: [PATCH] Add Adafruit pitft35 touchscreen support (#1657)
-
-The dts comes from the Adafruit repository
-
- https://github.com/adafruit/Adafruit-Pi-Kernel-o-Matic/blob/pitft/pitft35r-overlay.dts
-
-Reformatted slightly to match conventions in the pitft28-resistive-overlay.
-
-Signed-off-by: Scott Ellis <scott at jumpnowtek.com>
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 12 ++
- .../dts/overlays/pitft35-resistive-overlay.dts | 121 +++++++++++++++++++++
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 5 files changed, 136 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/pitft35-resistive-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -65,6 +65,7 @@ dtbo-$(RPI_DT_OVERLAYS) += piscreen2r.dt
- dtbo-$(RPI_DT_OVERLAYS) += pitft22.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += pitft28-capacitive.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += pitft28-resistive.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += pitft35-resistive.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += pps-gpio.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += pwm.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += pwm-2chan.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -854,6 +854,18 @@ Params: speed Display
- debug Debug output level {0-7}
-
-
-+Name: pitft35-resistive
-+Info: Adafruit PiTFT 3.5" resistive touch screen
-+Load: dtoverlay=pitft35-resistive,<param>=<val>
-+Params: speed Display SPI bus speed
-+
-+ rotate Display rotation {0,90,180,270}
-+
-+ fps Delay between frame updates
-+
-+ debug Debug output level {0-7}
-+
-+
- Name: pps-gpio
- Info: Configures the pps-gpio (pulse-per-second time signal via GPIO).
- Load: dtoverlay=pps-gpio,<param>=<val>
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/pitft35-resistive-overlay.dts
-@@ -0,0 +1,121 @@
-+/*
-+ * Device Tree overlay for Adafruit PiTFT 3.5" resistive touch screen
-+ *
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&spidev0>;
-+ __overlay__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&spidev1>;
-+ __overlay__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ fragment at 3 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ pitft_pins: pitft_pins {
-+ brcm,pins = <24 25>;
-+ brcm,function = <0 1>; /* in out */
-+ brcm,pull = <2 0>; /* pullup none */
-+ };
-+ };
-+ };
-+
-+ fragment at 4 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ /* needed to avoid dtc warning */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ pitft: pitft at 0{
-+ compatible = "himax,hx8357d";
-+ reg = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pitft_pins>;
-+
-+ spi-max-frequency = <32000000>;
-+ rotate = <90>;
-+ fps = <25>;
-+ bgr;
-+ buswidth = <8>;
-+ dc-gpios = <&gpio 25 0>;
-+ debug = <0>;
-+ };
-+
-+ pitft_ts at 1 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ compatible = "st,stmpe610";
-+ reg = <1>;
-+
-+ spi-max-frequency = <500000>;
-+ irq-gpio = <&gpio 24 0x2>; /* IRQF_TRIGGER_FALLING */
-+ interrupts = <24 2>; /* high-to-low edge triggered */
-+ interrupt-parent = <&gpio>;
-+ interrupt-controller;
-+
-+ stmpe_touchscreen {
-+ compatible = "st,stmpe-ts";
-+ st,sample-time = <4>;
-+ st,mod-12b = <1>;
-+ st,ref-sel = <0>;
-+ st,adc-freq = <2>;
-+ st,ave-ctrl = <3>;
-+ st,touch-det-delay = <4>;
-+ st,settling = <2>;
-+ st,fraction-z = <7>;
-+ st,i-drive = <0>;
-+ };
-+
-+ stmpe_gpio: stmpe_gpio {
-+ #gpio-cells = <2>;
-+ compatible = "st,stmpe-gpio";
-+ /*
-+ * only GPIO2 is wired/available
-+ * and it is wired to the backlight
-+ */
-+ st,norequest-mask = <0x7b>;
-+ };
-+ };
-+ };
-+ };
-+
-+ fragment at 5 {
-+ target-path = "/soc";
-+ __overlay__ {
-+ backlight {
-+ compatible = "gpio-backlight";
-+ gpios = <&stmpe_gpio 2 0>;
-+ default-on;
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ speed = <&pitft>,"spi-max-frequency:0";
-+ rotate = <&pitft>,"rotate:0";
-+ fps = <&pitft>,"fps:0";
-+ debug = <&pitft>,"debug:0";
-+ };
-+};
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -1116,6 +1116,7 @@ CONFIG_FB_TFT_BD663474=m
- CONFIG_FB_TFT_HX8340BN=m
- CONFIG_FB_TFT_HX8347D=m
- CONFIG_FB_TFT_HX8353D=m
-+CONFIG_FB_TFT_HX8357D=m
- CONFIG_FB_TFT_ILI9163=m
- CONFIG_FB_TFT_ILI9320=m
- CONFIG_FB_TFT_ILI9325=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -1123,6 +1123,7 @@ CONFIG_FB_TFT_BD663474=m
- CONFIG_FB_TFT_HX8340BN=m
- CONFIG_FB_TFT_HX8347D=m
- CONFIG_FB_TFT_HX8353D=m
-+CONFIG_FB_TFT_HX8357D=m
- CONFIG_FB_TFT_ILI9163=m
- CONFIG_FB_TFT_ILI9320=m
- CONFIG_FB_TFT_ILI9325=m
diff --git a/target/linux/brcm2708/patches-4.4/0512-drm-vc4-Fix-races-when-the-CS-reads-from-render-targ.patch b/target/linux/brcm2708/patches-4.4/0512-drm-vc4-Fix-races-when-the-CS-reads-from-render-targ.patch
deleted file mode 100644
index 4f6145d..0000000
--- a/target/linux/brcm2708/patches-4.4/0512-drm-vc4-Fix-races-when-the-CS-reads-from-render-targ.patch
+++ /dev/null
@@ -1,220 +0,0 @@
-From 5e074566a22f9fd5107c2c6d4d96a1e9a477294c Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 27 Sep 2016 09:03:13 -0700
-Subject: [PATCH] drm/vc4: Fix races when the CS reads from render targets.
-
-With the introduction of bin/render pipelining, the previous job may
-not be completed when we start binning the next one. If the previous
-job wrote our VBO, IB, or CS textures, then the binning stage might
-get stale or uninitialized results.
-
-Fixes the major rendering failure in glmark2 -b terrain.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Fixes: ca26d28bbaa3 ("drm/vc4: improve throughput by pipelining binning and rendering jobs")
-Cc: stable at vger.kernel.org
----
- drivers/gpu/drm/vc4/vc4_drv.h | 19 ++++++++++++++++++-
- drivers/gpu/drm/vc4/vc4_gem.c | 13 +++++++++++++
- drivers/gpu/drm/vc4/vc4_render_cl.c | 21 +++++++++++++++++----
- drivers/gpu/drm/vc4/vc4_validate.c | 17 ++++++++++++++---
- 4 files changed, 62 insertions(+), 8 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_drv.h
-+++ b/drivers/gpu/drm/vc4/vc4_drv.h
-@@ -129,9 +129,16 @@ to_vc4_dev(struct drm_device *dev)
- struct vc4_bo {
- struct drm_gem_cma_object base;
-
-- /* seqno of the last job to render to this BO. */
-+ /* seqno of the last job to render using this BO. */
- uint64_t seqno;
-
-+ /* seqno of the last job to use the RCL to write to this BO.
-+ *
-+ * Note that this doesn't include binner overflow memory
-+ * writes.
-+ */
-+ uint64_t write_seqno;
-+
- /* List entry for the BO's position in either
- * vc4_exec_info->unref_list or vc4_dev->bo_cache.time_list
- */
-@@ -227,6 +234,9 @@ struct vc4_exec_info {
- /* Sequence number for this bin/render job. */
- uint64_t seqno;
-
-+ /* Latest write_seqno of any BO that binning depends on. */
-+ uint64_t bin_dep_seqno;
-+
- /* Last current addresses the hardware was processing when the
- * hangcheck timer checked on us.
- */
-@@ -241,6 +251,13 @@ struct vc4_exec_info {
- struct drm_gem_cma_object **bo;
- uint32_t bo_count;
-
-+ /* List of BOs that are being written by the RCL. Other than
-+ * the binner temporary storage, this is all the BOs written
-+ * by the job.
-+ */
-+ struct drm_gem_cma_object *rcl_write_bo[4];
-+ uint32_t rcl_write_bo_count;
-+
- /* Pointers for our position in vc4->job_list */
- struct list_head head;
-
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -483,6 +483,11 @@ vc4_update_bo_seqnos(struct vc4_exec_inf
- list_for_each_entry(bo, &exec->unref_list, unref_head) {
- bo->seqno = seqno;
- }
-+
-+ for (i = 0; i < exec->rcl_write_bo_count; i++) {
-+ bo = to_vc4_bo(&exec->rcl_write_bo[i]->base);
-+ bo->write_seqno = seqno;
-+ }
- }
-
- /* Queues a struct vc4_exec_info for execution. If no job is
-@@ -685,6 +690,14 @@ vc4_get_bcl(struct drm_device *dev, stru
- goto fail;
-
- ret = vc4_validate_shader_recs(dev, exec);
-+ if (ret)
-+ goto fail;
-+
-+ /* Block waiting on any previous rendering into the CS's VBO,
-+ * IB, or textures, so that pixels are actually written by the
-+ * time we try to read them.
-+ */
-+ ret = vc4_wait_for_seqno(dev, exec->bin_dep_seqno, ~0ull, true);
-
- fail:
- kfree(temp);
---- a/drivers/gpu/drm/vc4/vc4_render_cl.c
-+++ b/drivers/gpu/drm/vc4/vc4_render_cl.c
-@@ -45,6 +45,8 @@ struct vc4_rcl_setup {
-
- struct drm_gem_cma_object *rcl;
- u32 next_offset;
-+
-+ u32 next_write_bo_index;
- };
-
- static inline void rcl_u8(struct vc4_rcl_setup *setup, u8 val)
-@@ -407,6 +409,8 @@ static int vc4_rcl_msaa_surface_setup(st
- if (!*obj)
- return -EINVAL;
-
-+ exec->rcl_write_bo[exec->rcl_write_bo_count++] = *obj;
-+
- if (surf->offset & 0xf) {
- DRM_ERROR("MSAA write must be 16b aligned.\n");
- return -EINVAL;
-@@ -417,7 +421,8 @@ static int vc4_rcl_msaa_surface_setup(st
-
- static int vc4_rcl_surface_setup(struct vc4_exec_info *exec,
- struct drm_gem_cma_object **obj,
-- struct drm_vc4_submit_rcl_surface *surf)
-+ struct drm_vc4_submit_rcl_surface *surf,
-+ bool is_write)
- {
- uint8_t tiling = VC4_GET_FIELD(surf->bits,
- VC4_LOADSTORE_TILE_BUFFER_TILING);
-@@ -440,6 +445,9 @@ static int vc4_rcl_surface_setup(struct
- if (!*obj)
- return -EINVAL;
-
-+ if (is_write)
-+ exec->rcl_write_bo[exec->rcl_write_bo_count++] = *obj;
-+
- if (surf->flags & VC4_SUBMIT_RCL_SURFACE_READ_IS_FULL_RES) {
- if (surf == &exec->args->zs_write) {
- DRM_ERROR("general zs write may not be a full-res.\n");
-@@ -542,6 +550,8 @@ vc4_rcl_render_config_surface_setup(stru
- if (!*obj)
- return -EINVAL;
-
-+ exec->rcl_write_bo[exec->rcl_write_bo_count++] = *obj;
-+
- if (tiling > VC4_TILING_FORMAT_LT) {
- DRM_ERROR("Bad tiling format\n");
- return -EINVAL;
-@@ -599,15 +609,18 @@ int vc4_get_rcl(struct drm_device *dev,
- if (ret)
- return ret;
-
-- ret = vc4_rcl_surface_setup(exec, &setup.color_read, &args->color_read);
-+ ret = vc4_rcl_surface_setup(exec, &setup.color_read, &args->color_read,
-+ false);
- if (ret)
- return ret;
-
-- ret = vc4_rcl_surface_setup(exec, &setup.zs_read, &args->zs_read);
-+ ret = vc4_rcl_surface_setup(exec, &setup.zs_read, &args->zs_read,
-+ false);
- if (ret)
- return ret;
-
-- ret = vc4_rcl_surface_setup(exec, &setup.zs_write, &args->zs_write);
-+ ret = vc4_rcl_surface_setup(exec, &setup.zs_write, &args->zs_write,
-+ true);
- if (ret)
- return ret;
-
---- a/drivers/gpu/drm/vc4/vc4_validate.c
-+++ b/drivers/gpu/drm/vc4/vc4_validate.c
-@@ -267,6 +267,9 @@ validate_indexed_prim_list(VALIDATE_ARGS
- if (!ib)
- return -EINVAL;
-
-+ exec->bin_dep_seqno = max(exec->bin_dep_seqno,
-+ to_vc4_bo(&ib->base)->write_seqno);
-+
- if (offset > ib->base.size ||
- (ib->base.size - offset) / index_size < length) {
- DRM_ERROR("IB access overflow (%d + %d*%d > %zd)\n",
-@@ -555,8 +558,7 @@ static bool
- reloc_tex(struct vc4_exec_info *exec,
- void *uniform_data_u,
- struct vc4_texture_sample_info *sample,
-- uint32_t texture_handle_index)
--
-+ uint32_t texture_handle_index, bool is_cs)
- {
- struct drm_gem_cma_object *tex;
- uint32_t p0 = *(uint32_t *)(uniform_data_u + sample->p_offset[0]);
-@@ -714,6 +716,11 @@ reloc_tex(struct vc4_exec_info *exec,
-
- *validated_p0 = tex->paddr + p0;
-
-+ if (is_cs) {
-+ exec->bin_dep_seqno = max(exec->bin_dep_seqno,
-+ to_vc4_bo(&tex->base)->write_seqno);
-+ }
-+
- return true;
- fail:
- DRM_INFO("Texture p0 at %d: 0x%08x\n", sample->p_offset[0], p0);
-@@ -835,7 +842,8 @@ validate_gl_shader_rec(struct drm_device
- if (!reloc_tex(exec,
- uniform_data_u,
- &validated_shader->texture_samples[tex],
-- texture_handles_u[tex])) {
-+ texture_handles_u[tex],
-+ i == 2)) {
- return -EINVAL;
- }
- }
-@@ -867,6 +875,9 @@ validate_gl_shader_rec(struct drm_device
- uint32_t stride = *(uint8_t *)(pkt_u + o + 5);
- uint32_t max_index;
-
-+ exec->bin_dep_seqno = max(exec->bin_dep_seqno,
-+ to_vc4_bo(&vbo->base)->write_seqno);
-+
- if (state->addr & 0x8)
- stride |= (*(uint32_t *)(pkt_u + 100 + i * 4)) & ~0xff;
-
diff --git a/target/linux/brcm2708/patches-4.4/0513-drm-vc4-Fix-up-the-limited-range-RGB-output-commit.patch b/target/linux/brcm2708/patches-4.4/0513-drm-vc4-Fix-up-the-limited-range-RGB-output-commit.patch
deleted file mode 100644
index 8019b35..0000000
--- a/target/linux/brcm2708/patches-4.4/0513-drm-vc4-Fix-up-the-limited-range-RGB-output-commit.patch
+++ /dev/null
@@ -1,29 +0,0 @@
-From 10f677debaad1f0f45b1f0a70f48ebd92a03fd10 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Thu, 15 Sep 2016 17:52:17 +0100
-Subject: [PATCH] drm/vc4: Fix up the limited range RGB output commit.
-
-CEA mode #1 is the only one that doesn't do limited range, thus the
-strange pattern in other drivers.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_hdmi.c | 7 +++++--
- 1 file changed, 5 insertions(+), 2 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_hdmi.c
-+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
-@@ -343,8 +343,11 @@ static void vc4_hdmi_encoder_mode_set(st
- csc_ctl = VC4_SET_FIELD(VC4_HD_CSC_CTL_ORDER_BGR,
- VC4_HD_CSC_CTL_ORDER);
-
-- if (vc4_encoder->hdmi_monitor && drm_match_cea_mode(mode) != 0) {
-- /* Enable limited range RGB output. This matrix is:
-+ if (vc4_encoder->hdmi_monitor && drm_match_cea_mode(mode) > 1) {
-+ /* CEA VICs other than #1 requre limited range RGB
-+ * output. Apply a colorspace conversion to squash
-+ * 0-255 down to 16-235. The matrix here is:
-+ *
- * [ 0 0 0.8594 16]
- * [ 0 0.8594 0 16]
- * [ 0.8594 0 0 16]
diff --git a/target/linux/brcm2708/patches-4.4/0514-drm-vc4-Increase-timeout-for-HDMI_SCHEDULER_CONTROL-.patch b/target/linux/brcm2708/patches-4.4/0514-drm-vc4-Increase-timeout-for-HDMI_SCHEDULER_CONTROL-.patch
deleted file mode 100644
index 450d67a..0000000
--- a/target/linux/brcm2708/patches-4.4/0514-drm-vc4-Increase-timeout-for-HDMI_SCHEDULER_CONTROL-.patch
+++ /dev/null
@@ -1,34 +0,0 @@
-From c8d14db6e63978e7075fcf37385342db604cbf2c Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Wed, 28 Sep 2016 17:21:05 -0700
-Subject: [PATCH] drm/vc4: Increase timeout for HDMI_SCHEDULER_CONTROL changes.
-
-Fixes occasional debug spew at boot when connected directly through
-HDMI, and probably confusing the HDMI state machine when we go trying
-to poke registers for the enable sequence too soon.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_hdmi.c | 4 ++--
- 1 file changed, 2 insertions(+), 2 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_hdmi.c
-+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
-@@ -408,7 +408,7 @@ static void vc4_hdmi_encoder_enable(stru
- VC4_HDMI_SCHEDULER_CONTROL_MODE_HDMI);
-
- ret = wait_for(HDMI_READ(VC4_HDMI_SCHEDULER_CONTROL) &
-- VC4_HDMI_SCHEDULER_CONTROL_HDMI_ACTIVE, 1);
-+ VC4_HDMI_SCHEDULER_CONTROL_HDMI_ACTIVE, 1000);
- WARN_ONCE(ret, "Timeout waiting for "
- "VC4_HDMI_SCHEDULER_CONTROL_HDMI_ACTIVE\n");
- } else {
-@@ -420,7 +420,7 @@ static void vc4_hdmi_encoder_enable(stru
- ~VC4_HDMI_SCHEDULER_CONTROL_MODE_HDMI);
-
- ret = wait_for(!(HDMI_READ(VC4_HDMI_SCHEDULER_CONTROL) &
-- VC4_HDMI_SCHEDULER_CONTROL_HDMI_ACTIVE), 1);
-+ VC4_HDMI_SCHEDULER_CONTROL_HDMI_ACTIVE), 1000);
- WARN_ONCE(ret, "Timeout waiting for "
- "!VC4_HDMI_SCHEDULER_CONTROL_HDMI_ACTIVE\n");
- }
diff --git a/target/linux/brcm2708/patches-4.4/0515-drm-vc4-Disallow-interlaced-modes-on-DPI.patch b/target/linux/brcm2708/patches-4.4/0515-drm-vc4-Disallow-interlaced-modes-on-DPI.patch
deleted file mode 100644
index 3213c53..0000000
--- a/target/linux/brcm2708/patches-4.4/0515-drm-vc4-Disallow-interlaced-modes-on-DPI.patch
+++ /dev/null
@@ -1,37 +0,0 @@
-From b03aa8d12928c3413b3f02fd7c52d900edee196a Mon Sep 17 00:00:00 2001
-From: Mario Kleiner <mario.kleiner.de at gmail.com>
-Date: Tue, 19 Jul 2016 20:58:57 +0200
-Subject: [PATCH] drm/vc4: Disallow interlaced modes on DPI.
-
-We already don't expose such modes to userspace, but make
-sure userspace can't sneak some interlaced mode in.
-
-Signed-off-by: Mario Kleiner <mario.kleiner.de at gmail.com>
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_dpi.c | 11 +++++++++++
- 1 file changed, 11 insertions(+)
-
---- a/drivers/gpu/drm/vc4/vc4_dpi.c
-+++ b/drivers/gpu/drm/vc4/vc4_dpi.c
-@@ -349,9 +349,20 @@ static void vc4_dpi_encoder_enable(struc
- }
- }
-
-+static bool vc4_dpi_encoder_mode_fixup(struct drm_encoder *encoder,
-+ const struct drm_display_mode *mode,
-+ struct drm_display_mode *adjusted_mode)
-+{
-+ if (adjusted_mode->flags & DRM_MODE_FLAG_INTERLACE)
-+ return false;
-+
-+ return true;
-+}
-+
- static const struct drm_encoder_helper_funcs vc4_dpi_encoder_helper_funcs = {
- .disable = vc4_dpi_encoder_disable,
- .enable = vc4_dpi_encoder_enable,
-+ .mode_fixup = vc4_dpi_encoder_mode_fixup,
- };
-
- static const struct of_device_id vc4_dpi_dt_match[] = {
diff --git a/target/linux/brcm2708/patches-4.4/0516-drm-vc4-Fix-handling-of-interlaced-video-modes.patch b/target/linux/brcm2708/patches-4.4/0516-drm-vc4-Fix-handling-of-interlaced-video-modes.patch
deleted file mode 100644
index 6c82cbd..0000000
--- a/target/linux/brcm2708/patches-4.4/0516-drm-vc4-Fix-handling-of-interlaced-video-modes.patch
+++ /dev/null
@@ -1,104 +0,0 @@
-From 074d7a2c41bbfa252b7c1f1d85b355dce89dcbe7 Mon Sep 17 00:00:00 2001
-From: Mario Kleiner <mario.kleiner.de at gmail.com>
-Date: Tue, 19 Jul 2016 20:58:58 +0200
-Subject: [PATCH] drm/vc4: Fix handling of interlaced video modes.
-
-We must not apply CRTC_INTERLACE_HALVE_V to interlaced modes during
-mode enumeration, as drm_helper_probe_single_connector_modes
-does, so wrap it and reset the effect of CRTC_INTERLACE_HALVE_V
-on affected interlaced modes.
-
-Also mode_fixup interlaced modes passed in from user space.
-
-This fixes the vblank timestamping constants and entries in
-the mode->crtc_xxx fields needed for precise vblank timestamping.
-
-Signed-off-by: Mario Kleiner <mario.kleiner.de at gmail.com>
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_crtc.c | 18 ++++++++++++++++++
- drivers/gpu/drm/vc4/vc4_hdmi.c | 29 +++++++++++++++++++++++++++--
- 2 files changed, 45 insertions(+), 2 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_crtc.c
-+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
-@@ -538,6 +538,23 @@ static void vc4_crtc_enable(struct drm_c
- CRTC_READ(PV_V_CONTROL) | PV_VCONTROL_VIDEN);
- }
-
-+static bool vc4_crtc_mode_fixup(struct drm_crtc *crtc,
-+ const struct drm_display_mode *mode,
-+ struct drm_display_mode *adjusted_mode)
-+{
-+ /*
-+ * Interlaced video modes got CRTC_INTERLACE_HALVE_V applied when
-+ * coming from user space. We don't want this, as it screws up
-+ * vblank timestamping, so fix it up.
-+ */
-+ drm_mode_set_crtcinfo(adjusted_mode, 0);
-+
-+ DRM_DEBUG_KMS("[CRTC:%d] adjusted_mode :\n", crtc->base.id);
-+ drm_mode_debug_printmodeline(adjusted_mode);
-+
-+ return true;
-+}
-+
- static int vc4_crtc_atomic_check(struct drm_crtc *crtc,
- struct drm_crtc_state *state)
- {
-@@ -848,6 +865,7 @@ static const struct drm_crtc_helper_func
- .mode_set_nofb = vc4_crtc_mode_set_nofb,
- .disable = vc4_crtc_disable,
- .enable = vc4_crtc_enable,
-+ .mode_fixup = vc4_crtc_mode_fixup,
- .atomic_check = vc4_crtc_atomic_check,
- .atomic_flush = vc4_crtc_atomic_flush,
- };
---- a/drivers/gpu/drm/vc4/vc4_hdmi.c
-+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
-@@ -219,10 +219,35 @@ vc4_hdmi_connector_best_encoder(struct d
- return hdmi_connector->encoder;
- }
-
-+/*
-+ * drm_helper_probe_single_connector_modes() applies drm_mode_set_crtcinfo to
-+ * all modes with flag CRTC_INTERLACE_HALVE_V. We don't want this, as it
-+ * screws up vblank timestamping for interlaced modes, so fix it up.
-+ */
-+static int vc4_hdmi_connector_probe_modes(struct drm_connector *connector,
-+ uint32_t maxX, uint32_t maxY)
-+{
-+ struct drm_display_mode *mode;
-+ int count;
-+
-+ count = drm_helper_probe_single_connector_modes(connector, maxX, maxY);
-+ if (count == 0)
-+ return 0;
-+
-+ DRM_DEBUG_KMS("[CONNECTOR:%d:%s] probed adapted modes :\n",
-+ connector->base.id, connector->name);
-+ list_for_each_entry(mode, &connector->modes, head) {
-+ drm_mode_set_crtcinfo(mode, 0);
-+ drm_mode_debug_printmodeline(mode);
-+ }
-+
-+ return count;
-+}
-+
- static const struct drm_connector_funcs vc4_hdmi_connector_funcs = {
- .dpms = drm_atomic_helper_connector_dpms,
- .detect = vc4_hdmi_connector_detect,
-- .fill_modes = drm_helper_probe_single_connector_modes,
-+ .fill_modes = vc4_hdmi_connector_probe_modes,
- .destroy = vc4_hdmi_connector_destroy,
- .reset = drm_atomic_helper_connector_reset,
- .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
-@@ -258,7 +283,7 @@ static struct drm_connector *vc4_hdmi_co
- connector->polled = (DRM_CONNECTOR_POLL_CONNECT |
- DRM_CONNECTOR_POLL_DISCONNECT);
-
-- connector->interlace_allowed = 0;
-+ connector->interlace_allowed = 1;
- connector->doublescan_allowed = 0;
-
- drm_mode_connector_attach_encoder(connector, encoder);
diff --git a/target/linux/brcm2708/patches-4.4/0517-drm-vc4-Reject-doublescan-modes.patch b/target/linux/brcm2708/patches-4.4/0517-drm-vc4-Reject-doublescan-modes.patch
deleted file mode 100644
index a3a26e4..0000000
--- a/target/linux/brcm2708/patches-4.4/0517-drm-vc4-Reject-doublescan-modes.patch
+++ /dev/null
@@ -1,30 +0,0 @@
-From 39d618a032d26655dfa62299034394e5d1ea7712 Mon Sep 17 00:00:00 2001
-From: Mario Kleiner <mario.kleiner.de at gmail.com>
-Date: Tue, 19 Jul 2016 20:58:59 +0200
-Subject: [PATCH] drm/vc4: Reject doublescan modes.
-
-We can't handle doublescan modes at the moment, so if
-userspace tries to set one, reject the mode set.
-
-Signed-off-by: Mario Kleiner <mario.kleiner.de at gmail.com>
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_crtc.c | 7 +++++++
- 1 file changed, 7 insertions(+)
-
---- a/drivers/gpu/drm/vc4/vc4_crtc.c
-+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
-@@ -542,6 +542,13 @@ static bool vc4_crtc_mode_fixup(struct d
- const struct drm_display_mode *mode,
- struct drm_display_mode *adjusted_mode)
- {
-+ /* Do not allow doublescan modes from user space */
-+ if (adjusted_mode->flags & DRM_MODE_FLAG_DBLSCAN) {
-+ DRM_DEBUG_KMS("[CRTC:%d] Doublescan mode rejected.\n",
-+ crtc->base.id);
-+ return false;
-+ }
-+
- /*
- * Interlaced video modes got CRTC_INTERLACE_HALVE_V applied when
- * coming from user space. We don't want this, as it screws up
diff --git a/target/linux/brcm2708/patches-4.4/0518-drm-vc4-Enable-precise-vblank-timestamping-for-inter.patch b/target/linux/brcm2708/patches-4.4/0518-drm-vc4-Enable-precise-vblank-timestamping-for-inter.patch
deleted file mode 100644
index f2ba3b7..0000000
--- a/target/linux/brcm2708/patches-4.4/0518-drm-vc4-Enable-precise-vblank-timestamping-for-inter.patch
+++ /dev/null
@@ -1,61 +0,0 @@
-From d64055c8b7c73a95d30fe79300067b79b5b441ce Mon Sep 17 00:00:00 2001
-From: Mario Kleiner <mario.kleiner.de at gmail.com>
-Date: Tue, 19 Jul 2016 20:59:00 +0200
-Subject: [PATCH] drm/vc4: Enable precise vblank timestamping for interlaced
- modes.
-
-On top of the interlaced video mode fix and with some additional
-adjustments, this now works well. It has almost the same accuracy
-as on regular progressive scan modes.
-
-Signed-off-by: Mario Kleiner <mario.kleiner.de at gmail.com>
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_crtc.c | 21 ++++++++-------------
- 1 file changed, 8 insertions(+), 13 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_crtc.c
-+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
-@@ -154,14 +154,6 @@ int vc4_crtc_get_scanoutpos(struct drm_d
- if (vc4->firmware_kms)
- return 0;
-
-- /*
-- * XXX Doesn't work well in interlaced mode yet, partially due
-- * to problems in vc4 kms or drm core interlaced mode handling,
-- * so disable for now in interlaced mode.
-- */
-- if (mode->flags & DRM_MODE_FLAG_INTERLACE)
-- return ret;
--
- /* preempt_disable_rt() should go right here in PREEMPT_RT patchset. */
-
- /* Get optional system timestamp before query. */
-@@ -182,10 +174,15 @@ int vc4_crtc_get_scanoutpos(struct drm_d
-
- /* Vertical position of hvs composed scanline. */
- *vpos = VC4_GET_FIELD(val, SCALER_DISPSTATX_LINE);
-+ *hpos = 0;
-+
-+ if (mode->flags & DRM_MODE_FLAG_INTERLACE) {
-+ *vpos /= 2;
-
-- /* No hpos info available. */
-- if (hpos)
-- *hpos = 0;
-+ /* Use hpos to correct for field offset in interlaced mode. */
-+ if (VC4_GET_FIELD(val, SCALER_DISPSTATX_FRAME_COUNT) % 2)
-+ *hpos += mode->crtc_htotal / 2;
-+ }
-
- /* This is the offset we need for translating hvs -> pv scanout pos. */
- fifo_lines = vc4_crtc->cob_size / mode->crtc_hdisplay;
-@@ -208,8 +205,6 @@ int vc4_crtc_get_scanoutpos(struct drm_d
- * position of the PV.
- */
- *vpos -= fifo_lines + 1;
-- if (mode->flags & DRM_MODE_FLAG_INTERLACE)
-- *vpos /= 2;
-
- ret |= DRM_SCANOUTPOS_ACCURATE;
- return ret;
diff --git a/target/linux/brcm2708/patches-4.4/0519-drm-vc4-Enable-Disable-vblanks-properly-in-crtc-en-d.patch b/target/linux/brcm2708/patches-4.4/0519-drm-vc4-Enable-Disable-vblanks-properly-in-crtc-en-d.patch
deleted file mode 100644
index c04a314..0000000
--- a/target/linux/brcm2708/patches-4.4/0519-drm-vc4-Enable-Disable-vblanks-properly-in-crtc-en-d.patch
+++ /dev/null
@@ -1,38 +0,0 @@
-From b6184d2f6f80dd8abb6bd090830c76efe8f4e785 Mon Sep 17 00:00:00 2001
-From: Mario Kleiner <mario.kleiner.de at gmail.com>
-Date: Tue, 19 Jul 2016 20:59:01 +0200
-Subject: [PATCH] drm/vc4: Enable/Disable vblanks properly in crtc en/disable.
-
-Add missing drm_crtc_vblank_on/off() calls so vblank irq
-handling/updating/timestamping never runs with a crtc shut down
-or during its shutdown/startup, as that causes large jumps in
-vblank count and trouble for compositors.
-
-Signed-off-by: Mario Kleiner <mario.kleiner.de at gmail.com>
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_crtc.c | 6 ++++++
- 1 file changed, 6 insertions(+)
-
---- a/drivers/gpu/drm/vc4/vc4_crtc.c
-+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
-@@ -468,6 +468,9 @@ static void vc4_crtc_disable(struct drm_
- int ret;
- require_hvs_enabled(dev);
-
-+ /* Disable vblank irq handling before crtc is disabled. */
-+ drm_crtc_vblank_off(crtc);
-+
- if (VC4_DSI_USE_FIRMWARE_SETUP &&
- (CRTC_READ(PV_V_CONTROL) & PV_VCONTROL_DSI)) {
- /* Skip disabling the PV/HVS for the channel if it was
-@@ -531,6 +534,9 @@ static void vc4_crtc_enable(struct drm_c
- /* Turn on the pixel valve, which will emit the vstart signal. */
- CRTC_WRITE(PV_V_CONTROL,
- CRTC_READ(PV_V_CONTROL) | PV_VCONTROL_VIDEN);
-+
-+ /* Enable vblank irq handling after crtc is started. */
-+ drm_crtc_vblank_on(crtc);
- }
-
- static bool vc4_crtc_mode_fixup(struct drm_crtc *crtc,
diff --git a/target/linux/brcm2708/patches-4.4/0520-drm-vc4-Fix-support-for-interlaced-modes-on-HDMI.patch b/target/linux/brcm2708/patches-4.4/0520-drm-vc4-Fix-support-for-interlaced-modes-on-HDMI.patch
deleted file mode 100644
index 4e9aaa9..0000000
--- a/target/linux/brcm2708/patches-4.4/0520-drm-vc4-Fix-support-for-interlaced-modes-on-HDMI.patch
+++ /dev/null
@@ -1,211 +0,0 @@
-From 1aa0f9eb09ed1a1bfe303a6c2de1493274935661 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Wed, 28 Sep 2016 17:30:25 -0700
-Subject: [PATCH] drm/vc4: Fix support for interlaced modes on HDMI.
-
-We really do need to be using the halved V fields. I had been
-confused by the code I was using as a reference because it stored
-halved vsync fields but not halved vdisplay, so it looked like I only
-needed to divide vdisplay by 2.
-
-This reverts part of Mario's timestamping fixes that prevented
-CRTC_HALVE_V from applying, and instead adjusts the timestamping code
-to not use the crtc field in that case.
-
-Fixes locking of 1920x1080x60i on my Dell 2408WFP. There are black
-bars on the top and bottom, but I suspect that might be an
-under/overscan flags problem as opposed to video timings.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_crtc.c | 54 +++++++++++++++++++++++-------------------
- drivers/gpu/drm/vc4/vc4_hdmi.c | 45 ++++++++++-------------------------
- drivers/gpu/drm/vc4/vc4_regs.h | 3 +++
- 3 files changed, 44 insertions(+), 58 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_crtc.c
-+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
-@@ -220,7 +220,7 @@ int vc4_crtc_get_scanoutpos(struct drm_d
- * and need to make things up in a approximative but consistent way.
- */
- ret |= DRM_SCANOUTPOS_IN_VBLANK;
-- vblank_lines = mode->crtc_vtotal - mode->crtc_vdisplay;
-+ vblank_lines = mode->vtotal - mode->vdisplay;
-
- if (flags & DRM_CALLED_FROM_VBLIRQ) {
- /*
-@@ -368,7 +368,6 @@ static void vc4_crtc_mode_set_nofb(struc
- struct drm_crtc_state *state = crtc->state;
- struct drm_display_mode *mode = &state->adjusted_mode;
- bool interlace = mode->flags & DRM_MODE_FLAG_INTERLACE;
-- u32 vactive = (mode->vdisplay >> (interlace ? 1 : 0));
- bool is_dsi = (vc4_encoder->type == VC4_ENCODER_TYPE_DSI0 ||
- vc4_encoder->type == VC4_ENCODER_TYPE_DSI1);
- u32 format = is_dsi ? PV_CONTROL_FORMAT_DSIV_24 : PV_CONTROL_FORMAT_24;
-@@ -395,34 +394,49 @@ static void vc4_crtc_mode_set_nofb(struc
- VC4_SET_FIELD(mode->hdisplay, PV_HORZB_HACTIVE));
-
- CRTC_WRITE(PV_VERTA,
-- VC4_SET_FIELD(mode->vtotal - mode->vsync_end,
-+ VC4_SET_FIELD(mode->crtc_vtotal - mode->crtc_vsync_end,
- PV_VERTA_VBP) |
-- VC4_SET_FIELD(mode->vsync_end - mode->vsync_start,
-+ VC4_SET_FIELD(mode->crtc_vsync_end - mode->crtc_vsync_start,
- PV_VERTA_VSYNC));
- CRTC_WRITE(PV_VERTB,
-- VC4_SET_FIELD(mode->vsync_start - mode->vdisplay,
-+ VC4_SET_FIELD(mode->crtc_vsync_start - mode->crtc_vdisplay,
- PV_VERTB_VFP) |
-- VC4_SET_FIELD(vactive, PV_VERTB_VACTIVE));
-+ VC4_SET_FIELD(mode->crtc_vdisplay, PV_VERTB_VACTIVE));
-
- if (interlace) {
- CRTC_WRITE(PV_VERTA_EVEN,
-- VC4_SET_FIELD(mode->vtotal - mode->vsync_end - 1,
-+ VC4_SET_FIELD(mode->crtc_vtotal -
-+ mode->crtc_vsync_end - 1,
- PV_VERTA_VBP) |
-- VC4_SET_FIELD(mode->vsync_end - mode->vsync_start,
-+ VC4_SET_FIELD(mode->crtc_vsync_end -
-+ mode->crtc_vsync_start,
- PV_VERTA_VSYNC));
- CRTC_WRITE(PV_VERTB_EVEN,
-- VC4_SET_FIELD(mode->vsync_start - mode->vdisplay,
-+ VC4_SET_FIELD(mode->crtc_vsync_start -
-+ mode->crtc_vdisplay,
- PV_VERTB_VFP) |
-- VC4_SET_FIELD(vactive, PV_VERTB_VACTIVE));
-+ VC4_SET_FIELD(mode->crtc_vdisplay, PV_VERTB_VACTIVE));
-+
-+ /* We set up first field even mode for HDMI. VEC's
-+ * NTSC mode would want first field odd instead, once
-+ * we support it (to do so, set ODD_FIRST and put the
-+ * delay in VSYNCD_EVEN instead).
-+ */
-+ CRTC_WRITE(PV_V_CONTROL,
-+ PV_VCONTROL_CONTINUOUS |
-+ (is_dsi ? PV_VCONTROL_DSI : 0) |
-+ PV_VCONTROL_INTERLACE |
-+ VC4_SET_FIELD(mode->htotal / 2,
-+ PV_VCONTROL_ODD_DELAY));
-+ CRTC_WRITE(PV_VSYNCD_EVEN, 0);
-+ } else {
-+ CRTC_WRITE(PV_V_CONTROL,
-+ PV_VCONTROL_CONTINUOUS |
-+ (is_dsi ? PV_VCONTROL_DSI : 0));
- }
-
- CRTC_WRITE(PV_HACT_ACT, mode->hdisplay);
-
-- CRTC_WRITE(PV_V_CONTROL,
-- PV_VCONTROL_CONTINUOUS |
-- (is_dsi ? PV_VCONTROL_DSI : 0) |
-- (interlace ? PV_VCONTROL_INTERLACE : 0));
--
- CRTC_WRITE(PV_CONTROL,
- VC4_SET_FIELD(format, PV_CONTROL_FORMAT) |
- VC4_SET_FIELD(vc4_get_fifo_full_level(format),
-@@ -550,16 +564,6 @@ static bool vc4_crtc_mode_fixup(struct d
- return false;
- }
-
-- /*
-- * Interlaced video modes got CRTC_INTERLACE_HALVE_V applied when
-- * coming from user space. We don't want this, as it screws up
-- * vblank timestamping, so fix it up.
-- */
-- drm_mode_set_crtcinfo(adjusted_mode, 0);
--
-- DRM_DEBUG_KMS("[CRTC:%d] adjusted_mode :\n", crtc->base.id);
-- drm_mode_debug_printmodeline(adjusted_mode);
--
- return true;
- }
-
---- a/drivers/gpu/drm/vc4/vc4_hdmi.c
-+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
-@@ -219,35 +219,10 @@ vc4_hdmi_connector_best_encoder(struct d
- return hdmi_connector->encoder;
- }
-
--/*
-- * drm_helper_probe_single_connector_modes() applies drm_mode_set_crtcinfo to
-- * all modes with flag CRTC_INTERLACE_HALVE_V. We don't want this, as it
-- * screws up vblank timestamping for interlaced modes, so fix it up.
-- */
--static int vc4_hdmi_connector_probe_modes(struct drm_connector *connector,
-- uint32_t maxX, uint32_t maxY)
--{
-- struct drm_display_mode *mode;
-- int count;
--
-- count = drm_helper_probe_single_connector_modes(connector, maxX, maxY);
-- if (count == 0)
-- return 0;
--
-- DRM_DEBUG_KMS("[CONNECTOR:%d:%s] probed adapted modes :\n",
-- connector->base.id, connector->name);
-- list_for_each_entry(mode, &connector->modes, head) {
-- drm_mode_set_crtcinfo(mode, 0);
-- drm_mode_debug_printmodeline(mode);
-- }
--
-- return count;
--}
--
- static const struct drm_connector_funcs vc4_hdmi_connector_funcs = {
- .dpms = drm_atomic_helper_connector_dpms,
- .detect = vc4_hdmi_connector_detect,
-- .fill_modes = vc4_hdmi_connector_probe_modes,
-+ .fill_modes = drm_helper_probe_single_connector_modes,
- .destroy = vc4_hdmi_connector_destroy,
- .reset = drm_atomic_helper_connector_reset,
- .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
-@@ -316,16 +291,20 @@ static void vc4_hdmi_encoder_mode_set(st
- bool debug_dump_regs = false;
- bool hsync_pos = mode->flags & DRM_MODE_FLAG_PHSYNC;
- bool vsync_pos = mode->flags & DRM_MODE_FLAG_PVSYNC;
-- u32 vactive = (mode->vdisplay >>
-- ((mode->flags & DRM_MODE_FLAG_INTERLACE) ? 1 : 0));
-- u32 verta = (VC4_SET_FIELD(mode->vsync_end - mode->vsync_start,
-+ bool interlaced = mode->flags & DRM_MODE_FLAG_INTERLACE;
-+ u32 verta = (VC4_SET_FIELD(mode->crtc_vsync_end - mode->crtc_vsync_start,
- VC4_HDMI_VERTA_VSP) |
-- VC4_SET_FIELD(mode->vsync_start - mode->vdisplay,
-+ VC4_SET_FIELD(mode->crtc_vsync_start - mode->crtc_vdisplay,
- VC4_HDMI_VERTA_VFP) |
-- VC4_SET_FIELD(vactive, VC4_HDMI_VERTA_VAL));
-+ VC4_SET_FIELD(mode->crtc_vdisplay, VC4_HDMI_VERTA_VAL));
- u32 vertb = (VC4_SET_FIELD(0, VC4_HDMI_VERTB_VSPO) |
-- VC4_SET_FIELD(mode->vtotal - mode->vsync_end,
-+ VC4_SET_FIELD(mode->crtc_vtotal - mode->crtc_vsync_end,
- VC4_HDMI_VERTB_VBP));
-+ u32 vertb_even = (VC4_SET_FIELD(0, VC4_HDMI_VERTB_VSPO) |
-+ VC4_SET_FIELD(mode->crtc_vtotal -
-+ mode->crtc_vsync_end -
-+ interlaced,
-+ VC4_HDMI_VERTB_VBP));
- u32 csc_ctl;
-
- if (debug_dump_regs) {
-@@ -358,7 +337,7 @@ static void vc4_hdmi_encoder_mode_set(st
- HDMI_WRITE(VC4_HDMI_VERTA0, verta);
- HDMI_WRITE(VC4_HDMI_VERTA1, verta);
-
-- HDMI_WRITE(VC4_HDMI_VERTB0, vertb);
-+ HDMI_WRITE(VC4_HDMI_VERTB0, vertb_even);
- HDMI_WRITE(VC4_HDMI_VERTB1, vertb);
-
- HD_WRITE(VC4_HD_VID_CTL,
---- a/drivers/gpu/drm/vc4/vc4_regs.h
-+++ b/drivers/gpu/drm/vc4/vc4_regs.h
-@@ -183,6 +183,9 @@
- # define PV_CONTROL_EN BIT(0)
-
- #define PV_V_CONTROL 0x04
-+# define PV_VCONTROL_ODD_DELAY_MASK VC4_MASK(22, 6)
-+# define PV_VCONTROL_ODD_DELAY_SHIFT 6
-+# define PV_VCONTROL_ODD_FIRST BIT(5)
- # define PV_VCONTROL_INTERLACE BIT(4)
- # define PV_VCONTROL_DSI BIT(3)
- # define PV_VCONTROL_COMMAND BIT(2)
diff --git a/target/linux/brcm2708/patches-4.4/0521-clk-bcm2835-Clamp-the-PLL-s-requested-rate-to-the-ha.patch b/target/linux/brcm2708/patches-4.4/0521-clk-bcm2835-Clamp-the-PLL-s-requested-rate-to-the-ha.patch
deleted file mode 100644
index c6ae927..0000000
--- a/target/linux/brcm2708/patches-4.4/0521-clk-bcm2835-Clamp-the-PLL-s-requested-rate-to-the-ha.patch
+++ /dev/null
@@ -1,43 +0,0 @@
-From d9ab4b6b57e450db6a03df299079e8d80093ef45 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Wed, 28 Sep 2016 17:58:52 -0700
-Subject: [PATCH] clk: bcm2835: Clamp the PLL's requested rate to the hardware
- limits.
-
-Fixes setting low-resolution video modes on HDMI. Now the PLLH_PIX
-divider adjusts itself until the PLLH is within bounds.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/clk/bcm/clk-bcm2835.c | 11 ++++-------
- 1 file changed, 4 insertions(+), 7 deletions(-)
-
---- a/drivers/clk/bcm/clk-bcm2835.c
-+++ b/drivers/clk/bcm/clk-bcm2835.c
-@@ -523,8 +523,12 @@ static long bcm2835_pll_rate_from_diviso
- static long bcm2835_pll_round_rate(struct clk_hw *hw, unsigned long rate,
- unsigned long *parent_rate)
- {
-+ struct bcm2835_pll *pll = container_of(hw, struct bcm2835_pll, hw);
-+ const struct bcm2835_pll_data *data = pll->data;
- u32 ndiv, fdiv;
-
-+ rate = clamp(rate, data->min_rate, data->max_rate);
-+
- bcm2835_pll_choose_ndiv_and_fdiv(rate, *parent_rate, &ndiv, &fdiv);
-
- return bcm2835_pll_rate_from_divisors(*parent_rate, ndiv, fdiv, 1);
-@@ -629,13 +633,6 @@ static int bcm2835_pll_set_rate(struct c
- u32 ana[4];
- int i;
-
-- if (rate < data->min_rate || rate > data->max_rate) {
-- dev_err(cprman->dev, "%s: rate out of spec: %lu vs (%lu, %lu)\n",
-- clk_hw_get_name(hw), rate,
-- data->min_rate, data->max_rate);
-- return -EINVAL;
-- }
--
- if (rate > data->max_fb_rate) {
- use_fb_prediv = true;
- rate /= 2;
diff --git a/target/linux/brcm2708/patches-4.4/0522-drm-vc4-Set-up-the-AVI-and-SPD-infoframes.patch b/target/linux/brcm2708/patches-4.4/0522-drm-vc4-Set-up-the-AVI-and-SPD-infoframes.patch
deleted file mode 100644
index ec2a819..0000000
--- a/target/linux/brcm2708/patches-4.4/0522-drm-vc4-Set-up-the-AVI-and-SPD-infoframes.patch
+++ /dev/null
@@ -1,223 +0,0 @@
-From 244fda9f361b276c5697573b7aef7e89ee06c209 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Thu, 29 Sep 2016 10:34:21 -0700
-Subject: [PATCH] drm/vc4: Set up the AVI and SPD infoframes.
-
-Fixes a purple bar on the left side of the screen with my Dell
-2408WFP. It will also be required for supporting the double-clocked
-video modes.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_hdmi.c | 136 +++++++++++++++++++++++++++++++++++++++--
- drivers/gpu/drm/vc4/vc4_regs.h | 5 ++
- 2 files changed, 136 insertions(+), 5 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_hdmi.c
-+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
-@@ -62,6 +62,8 @@ struct vc4_hdmi {
- struct vc4_hdmi_encoder {
- struct vc4_encoder base;
- bool hdmi_monitor;
-+ bool limited_rgb_range;
-+ bool rgb_range_selectable;
- };
-
- static inline struct vc4_hdmi_encoder *
-@@ -205,6 +207,12 @@ static int vc4_hdmi_connector_get_modes(
- return -ENODEV;
-
- vc4_encoder->hdmi_monitor = drm_detect_hdmi_monitor(edid);
-+
-+ if (edid && edid->input & DRM_EDID_INPUT_DIGITAL) {
-+ vc4_encoder->rgb_range_selectable =
-+ drm_rgb_quant_range_selectable(edid);
-+ }
-+
- drm_mode_connector_update_edid_property(connector, edid);
- ret = drm_add_edid_modes(connector, edid);
-
-@@ -281,6 +289,117 @@ static const struct drm_encoder_funcs vc
- .destroy = vc4_hdmi_encoder_destroy,
- };
-
-+static int vc4_hdmi_stop_packet(struct drm_encoder *encoder,
-+ enum hdmi_infoframe_type type)
-+{
-+ struct drm_device *dev = encoder->dev;
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ u32 packet_id = type - 0x80;
-+
-+ HDMI_WRITE(VC4_HDMI_RAM_PACKET_CONFIG,
-+ HDMI_READ(VC4_HDMI_RAM_PACKET_CONFIG) & ~BIT(packet_id));
-+
-+ return wait_for(!(HDMI_READ(VC4_HDMI_RAM_PACKET_STATUS) &
-+ BIT(packet_id)), 100);
-+}
-+
-+static void vc4_hdmi_write_infoframe(struct drm_encoder *encoder,
-+ union hdmi_infoframe *frame)
-+{
-+ struct drm_device *dev = encoder->dev;
-+ struct vc4_dev *vc4 = to_vc4_dev(dev);
-+ u32 packet_id = frame->any.type - 0x80;
-+ u32 packet_reg = VC4_HDMI_GCP_0 + VC4_HDMI_PACKET_STRIDE * packet_id;
-+ uint8_t buffer[VC4_HDMI_PACKET_STRIDE];
-+ ssize_t len, i;
-+ int ret;
-+
-+ WARN_ONCE(!(HDMI_READ(VC4_HDMI_RAM_PACKET_CONFIG) &
-+ VC4_HDMI_RAM_PACKET_ENABLE),
-+ "Packet RAM has to be on to store the packet.");
-+
-+ len = hdmi_infoframe_pack(frame, buffer, sizeof(buffer));
-+ if (len < 0)
-+ return;
-+
-+ ret = vc4_hdmi_stop_packet(encoder, frame->any.type);
-+ if (ret) {
-+ DRM_ERROR("Failed to wait for infoframe to go idle: %d\n", ret);
-+ return;
-+ }
-+
-+ for (i = 0; i < len; i += 7) {
-+ HDMI_WRITE(packet_reg,
-+ buffer[i + 0] << 0 |
-+ buffer[i + 1] << 8 |
-+ buffer[i + 2] << 16);
-+ packet_reg += 4;
-+
-+ HDMI_WRITE(packet_reg,
-+ buffer[i + 3] << 0 |
-+ buffer[i + 4] << 8 |
-+ buffer[i + 5] << 16 |
-+ buffer[i + 6] << 24);
-+ packet_reg += 4;
-+ }
-+
-+ HDMI_WRITE(VC4_HDMI_RAM_PACKET_CONFIG,
-+ HDMI_READ(VC4_HDMI_RAM_PACKET_CONFIG) | BIT(packet_id));
-+ ret = wait_for((HDMI_READ(VC4_HDMI_RAM_PACKET_STATUS) &
-+ BIT(packet_id)), 100);
-+ if (ret)
-+ DRM_ERROR("Failed to wait for infoframe to start: %d\n", ret);
-+}
-+
-+static void vc4_hdmi_set_avi_infoframe(struct drm_encoder *encoder)
-+{
-+ struct vc4_hdmi_encoder *vc4_encoder = to_vc4_hdmi_encoder(encoder);
-+ struct drm_crtc *crtc = encoder->crtc;
-+ const struct drm_display_mode *mode = &crtc->state->adjusted_mode;
-+ union hdmi_infoframe frame;
-+ int ret;
-+
-+ ret = drm_hdmi_avi_infoframe_from_display_mode(&frame.avi, mode);
-+ if (ret < 0) {
-+ DRM_ERROR("couldn't fill AVI infoframe\n");
-+ return;
-+ }
-+
-+ if (vc4_encoder->rgb_range_selectable) {
-+ if (vc4_encoder->limited_rgb_range) {
-+ frame.avi.quantization_range =
-+ HDMI_QUANTIZATION_RANGE_LIMITED;
-+ } else {
-+ frame.avi.quantization_range =
-+ HDMI_QUANTIZATION_RANGE_FULL;
-+ }
-+ }
-+
-+ vc4_hdmi_write_infoframe(encoder, &frame);
-+}
-+
-+static void vc4_hdmi_set_spd_infoframe(struct drm_encoder *encoder)
-+{
-+ union hdmi_infoframe frame;
-+ int ret;
-+
-+ ret = hdmi_spd_infoframe_init(&frame.spd, "Broadcom", "Videocore");
-+ if (ret < 0) {
-+ DRM_ERROR("couldn't fill SPD infoframe\n");
-+ return;
-+ }
-+
-+ frame.spd.sdi = HDMI_SPD_SDI_PC;
-+
-+ vc4_hdmi_write_infoframe(encoder, &frame);
-+}
-+
-+static void vc4_hdmi_set_infoframes(struct drm_encoder *encoder)
-+{
-+ vc4_hdmi_set_avi_infoframe(encoder);
-+ vc4_hdmi_set_spd_infoframe(encoder);
-+}
-+
- static void vc4_hdmi_encoder_mode_set(struct drm_encoder *encoder,
- struct drm_display_mode *unadjusted_mode,
- struct drm_display_mode *mode)
-@@ -349,8 +468,9 @@ static void vc4_hdmi_encoder_mode_set(st
-
- if (vc4_encoder->hdmi_monitor && drm_match_cea_mode(mode) > 1) {
- /* CEA VICs other than #1 requre limited range RGB
-- * output. Apply a colorspace conversion to squash
-- * 0-255 down to 16-235. The matrix here is:
-+ * output unless overridden by an AVI infoframe.
-+ * Apply a colorspace conversion to squash 0-255 down
-+ * to 16-235. The matrix here is:
- *
- * [ 0 0 0.8594 16]
- * [ 0 0.8594 0 16]
-@@ -368,6 +488,9 @@ static void vc4_hdmi_encoder_mode_set(st
- HD_WRITE(VC4_HD_CSC_24_23, (0x100 << 16) | 0x000);
- HD_WRITE(VC4_HD_CSC_32_31, (0x000 << 16) | 0x6e0);
- HD_WRITE(VC4_HD_CSC_34_33, (0x100 << 16) | 0x000);
-+ vc4_encoder->limited_rgb_range = true;
-+ } else {
-+ vc4_encoder->limited_rgb_range = false;
- }
-
- /* The RGB order applies even when CSC is disabled. */
-@@ -386,6 +509,8 @@ static void vc4_hdmi_encoder_disable(str
- struct drm_device *dev = encoder->dev;
- struct vc4_dev *vc4 = to_vc4_dev(dev);
-
-+ HDMI_WRITE(VC4_HDMI_RAM_PACKET_CONFIG, 0);
-+
- HDMI_WRITE(VC4_HDMI_TX_PHY_RESET_CTL, 0xf << 16);
- HD_WRITE(VC4_HD_VID_CTL,
- HD_READ(VC4_HD_VID_CTL) & ~VC4_HD_VID_CTL_ENABLE);
-@@ -438,9 +563,10 @@ static void vc4_hdmi_encoder_enable(stru
- HDMI_READ(VC4_HDMI_SCHEDULER_CONTROL) |
- VC4_HDMI_SCHEDULER_CONTROL_VERT_ALWAYS_KEEPOUT);
-
-- /* XXX: Set HDMI_RAM_PACKET_CONFIG (1 << 16) and set
-- * up the infoframe.
-- */
-+ HDMI_WRITE(VC4_HDMI_RAM_PACKET_CONFIG,
-+ VC4_HDMI_RAM_PACKET_ENABLE);
-+
-+ vc4_hdmi_set_infoframes(encoder);
-
- drift = HDMI_READ(VC4_HDMI_FIFO_CTL);
- drift &= VC4_HDMI_FIFO_VALID_WRITE_MASK;
---- a/drivers/gpu/drm/vc4/vc4_regs.h
-+++ b/drivers/gpu/drm/vc4/vc4_regs.h
-@@ -443,6 +443,8 @@
- #define VC4_HDMI_RAM_PACKET_CONFIG 0x0a0
- # define VC4_HDMI_RAM_PACKET_ENABLE BIT(16)
-
-+#define VC4_HDMI_RAM_PACKET_STATUS 0x0a4
-+
- #define VC4_HDMI_HORZA 0x0c4
- # define VC4_HDMI_HORZA_VPOS BIT(14)
- # define VC4_HDMI_HORZA_HPOS BIT(13)
-@@ -504,6 +506,9 @@
-
- #define VC4_HDMI_TX_PHY_RESET_CTL 0x2c0
-
-+#define VC4_HDMI_GCP_0 0x400
-+#define VC4_HDMI_PACKET_STRIDE 0x24
-+
- #define VC4_HD_M_CTL 0x00c
- # define VC4_HD_M_REGISTER_FILE_STANDBY (3 << 6)
- # define VC4_HD_M_RAM_STANDBY (3 << 4)
diff --git a/target/linux/brcm2708/patches-4.4/0523-drm-vc4-Add-support-for-double-clocked-modes.patch b/target/linux/brcm2708/patches-4.4/0523-drm-vc4-Add-support-for-double-clocked-modes.patch
deleted file mode 100644
index eb3e82b..0000000
--- a/target/linux/brcm2708/patches-4.4/0523-drm-vc4-Add-support-for-double-clocked-modes.patch
+++ /dev/null
@@ -1,127 +0,0 @@
-From d8b55ad4f430625256e7a7b02c9ba0369adfe168 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Wed, 28 Sep 2016 19:01:48 -0700
-Subject: [PATCH] drm/vc4: Add support for double-clocked modes.
-
-Now that we have infoframes to report the pixel repeat flag, we can
-start using it. Fixes locking the 720x480i and 720x576i modes on my
-Dell 2408WFP. Like the 1920x1080i case, they don't fit properly on
-the screen, though.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_crtc.c | 17 +++++++++++------
- drivers/gpu/drm/vc4/vc4_hdmi.c | 16 +++++++++++-----
- drivers/gpu/drm/vc4/vc4_regs.h | 2 ++
- 3 files changed, 24 insertions(+), 11 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_crtc.c
-+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
-@@ -371,6 +371,7 @@ static void vc4_crtc_mode_set_nofb(struc
- bool is_dsi = (vc4_encoder->type == VC4_ENCODER_TYPE_DSI0 ||
- vc4_encoder->type == VC4_ENCODER_TYPE_DSI1);
- u32 format = is_dsi ? PV_CONTROL_FORMAT_DSIV_24 : PV_CONTROL_FORMAT_24;
-+ u32 pixel_rep = (mode->flags & DRM_MODE_FLAG_DBLCLK) ? 2 : 1;
- bool debug_dump_regs = false;
-
- if (debug_dump_regs) {
-@@ -384,14 +385,17 @@ static void vc4_crtc_mode_set_nofb(struc
- CRTC_WRITE(PV_CONTROL, 0);
-
- CRTC_WRITE(PV_HORZA,
-- VC4_SET_FIELD(mode->htotal - mode->hsync_end,
-+ VC4_SET_FIELD((mode->htotal -
-+ mode->hsync_end) * pixel_rep,
- PV_HORZA_HBP) |
-- VC4_SET_FIELD(mode->hsync_end - mode->hsync_start,
-+ VC4_SET_FIELD((mode->hsync_end -
-+ mode->hsync_start) * pixel_rep,
- PV_HORZA_HSYNC));
- CRTC_WRITE(PV_HORZB,
-- VC4_SET_FIELD(mode->hsync_start - mode->hdisplay,
-+ VC4_SET_FIELD((mode->hsync_start -
-+ mode->hdisplay) * pixel_rep,
- PV_HORZB_HFP) |
-- VC4_SET_FIELD(mode->hdisplay, PV_HORZB_HACTIVE));
-+ VC4_SET_FIELD(mode->hdisplay * pixel_rep, PV_HORZB_HACTIVE));
-
- CRTC_WRITE(PV_VERTA,
- VC4_SET_FIELD(mode->crtc_vtotal - mode->crtc_vsync_end,
-@@ -426,7 +430,7 @@ static void vc4_crtc_mode_set_nofb(struc
- PV_VCONTROL_CONTINUOUS |
- (is_dsi ? PV_VCONTROL_DSI : 0) |
- PV_VCONTROL_INTERLACE |
-- VC4_SET_FIELD(mode->htotal / 2,
-+ VC4_SET_FIELD(mode->htotal * pixel_rep / 2,
- PV_VCONTROL_ODD_DELAY));
- CRTC_WRITE(PV_VSYNCD_EVEN, 0);
- } else {
-@@ -435,12 +439,13 @@ static void vc4_crtc_mode_set_nofb(struc
- (is_dsi ? PV_VCONTROL_DSI : 0));
- }
-
-- CRTC_WRITE(PV_HACT_ACT, mode->hdisplay);
-+ CRTC_WRITE(PV_HACT_ACT, mode->hdisplay * pixel_rep);
-
- CRTC_WRITE(PV_CONTROL,
- VC4_SET_FIELD(format, PV_CONTROL_FORMAT) |
- VC4_SET_FIELD(vc4_get_fifo_full_level(format),
- PV_CONTROL_FIFO_LEVEL) |
-+ VC4_SET_FIELD(pixel_rep - 1, PV_CONTROL_PIXEL_REP) |
- PV_CONTROL_CLR_AT_START |
- PV_CONTROL_TRIGGER_UNDERFLOW |
- PV_CONTROL_WAIT_HSTART |
---- a/drivers/gpu/drm/vc4/vc4_hdmi.c
-+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
-@@ -411,6 +411,7 @@ static void vc4_hdmi_encoder_mode_set(st
- bool hsync_pos = mode->flags & DRM_MODE_FLAG_PHSYNC;
- bool vsync_pos = mode->flags & DRM_MODE_FLAG_PVSYNC;
- bool interlaced = mode->flags & DRM_MODE_FLAG_INTERLACE;
-+ u32 pixel_rep = (mode->flags & DRM_MODE_FLAG_DBLCLK) ? 2 : 1;
- u32 verta = (VC4_SET_FIELD(mode->crtc_vsync_end - mode->crtc_vsync_start,
- VC4_HDMI_VERTA_VSP) |
- VC4_SET_FIELD(mode->crtc_vsync_start - mode->crtc_vdisplay,
-@@ -433,7 +434,8 @@ static void vc4_hdmi_encoder_mode_set(st
-
- HD_WRITE(VC4_HD_VID_CTL, 0);
-
-- clk_set_rate(vc4->hdmi->pixel_clock, mode->clock * 1000);
-+ clk_set_rate(vc4->hdmi->pixel_clock, mode->clock * 1000 *
-+ ((mode->flags & DRM_MODE_FLAG_DBLCLK) ? 2 : 1));
-
- HDMI_WRITE(VC4_HDMI_SCHEDULER_CONTROL,
- HDMI_READ(VC4_HDMI_SCHEDULER_CONTROL) |
-@@ -443,14 +445,18 @@ static void vc4_hdmi_encoder_mode_set(st
- HDMI_WRITE(VC4_HDMI_HORZA,
- (vsync_pos ? VC4_HDMI_HORZA_VPOS : 0) |
- (hsync_pos ? VC4_HDMI_HORZA_HPOS : 0) |
-- VC4_SET_FIELD(mode->hdisplay, VC4_HDMI_HORZA_HAP));
-+ VC4_SET_FIELD(mode->hdisplay * pixel_rep,
-+ VC4_HDMI_HORZA_HAP));
-
- HDMI_WRITE(VC4_HDMI_HORZB,
-- VC4_SET_FIELD(mode->htotal - mode->hsync_end,
-+ VC4_SET_FIELD((mode->htotal -
-+ mode->hsync_end) * pixel_rep,
- VC4_HDMI_HORZB_HBP) |
-- VC4_SET_FIELD(mode->hsync_end - mode->hsync_start,
-+ VC4_SET_FIELD((mode->hsync_end -
-+ mode->hsync_start) * pixel_rep,
- VC4_HDMI_HORZB_HSP) |
-- VC4_SET_FIELD(mode->hsync_start - mode->hdisplay,
-+ VC4_SET_FIELD((mode->hsync_start -
-+ mode->hdisplay) * pixel_rep,
- VC4_HDMI_HORZB_HFP));
-
- HDMI_WRITE(VC4_HDMI_VERTA0, verta);
---- a/drivers/gpu/drm/vc4/vc4_regs.h
-+++ b/drivers/gpu/drm/vc4/vc4_regs.h
-@@ -175,6 +175,8 @@
- # define PV_CONTROL_CLR_AT_START BIT(14)
- # define PV_CONTROL_TRIGGER_UNDERFLOW BIT(13)
- # define PV_CONTROL_WAIT_HSTART BIT(12)
-+# define PV_CONTROL_PIXEL_REP_MASK VC4_MASK(5, 4)
-+# define PV_CONTROL_PIXEL_REP_SHIFT 4
- # define PV_CONTROL_CLK_SELECT_DSI_VEC 0
- # define PV_CONTROL_CLK_SELECT_DPI_SMI_HDMI 1
- # define PV_CONTROL_CLK_SELECT_MASK VC4_MASK(3, 2)
diff --git a/target/linux/brcm2708/patches-4.4/0524-BCM270X_DT-Update-CM3-to-use-sdhost-interface.patch b/target/linux/brcm2708/patches-4.4/0524-BCM270X_DT-Update-CM3-to-use-sdhost-interface.patch
deleted file mode 100644
index 8db6aa0..0000000
--- a/target/linux/brcm2708/patches-4.4/0524-BCM270X_DT-Update-CM3-to-use-sdhost-interface.patch
+++ /dev/null
@@ -1,36 +0,0 @@
-From c3ffa0b16968bf686fb46e3848ef8f31866e7c33 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 10 Oct 2016 15:06:20 +0100
-Subject: [PATCH] BCM270X_DT: Update CM3 to use sdhost interface
-
----
- arch/arm/boot/dts/bcm2710-rpi-cm3.dts | 9 ++++-----
- 1 file changed, 4 insertions(+), 5 deletions(-)
-
---- a/arch/arm/boot/dts/bcm2710-rpi-cm3.dts
-+++ b/arch/arm/boot/dts/bcm2710-rpi-cm3.dts
-@@ -8,10 +8,9 @@
- };
-
- &gpio {
--
-- mmc_pins: mmc_pins {
-+ sdhost_pins: sdhost_pins {
- brcm,pins = <48 49 50 51 52 53>;
-- brcm,function = <7>; /* alt3 */
-+ brcm,function = <4>; /* alt0 */
- brcm,pull = <0 2 2 2 2 2>;
- };
-
-@@ -46,9 +45,9 @@
- };
- };
-
--&mmc {
-+&sdhost {
- pinctrl-names = "default";
-- pinctrl-0 = <&mmc_pins>;
-+ pinctrl-0 = <&sdhost_pins>;
- non-removable;
- bus-width = <4>;
- status = "okay";
diff --git a/target/linux/brcm2708/patches-4.4/0525-drm-vc4-Fix-memory-leak-of-the-CRTC-state.patch b/target/linux/brcm2708/patches-4.4/0525-drm-vc4-Fix-memory-leak-of-the-CRTC-state.patch
deleted file mode 100644
index 8322813..0000000
--- a/target/linux/brcm2708/patches-4.4/0525-drm-vc4-Fix-memory-leak-of-the-CRTC-state.patch
+++ /dev/null
@@ -1,26 +0,0 @@
-From 26f0d649e4cdaff8d9aa9f151821f7d2219ddb54 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Mon, 10 Oct 2016 09:44:06 -0700
-Subject: [PATCH] drm/vc4: Fix memory leak of the CRTC state.
-
-The underscores variant frees the pointers inside, while the
-no-underscores variant calls underscores and then frees the struct.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Fixes: d8dbf44f13b9 ("drm/vc4: Make the CRTCs cooperate on allocating display lists.")
-Cc: stable at vger.kernel.org
----
- drivers/gpu/drm/vc4/vc4_crtc.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/gpu/drm/vc4/vc4_crtc.c
-+++ b/drivers/gpu/drm/vc4/vc4_crtc.c
-@@ -862,7 +862,7 @@ static void vc4_crtc_destroy_state(struc
-
- }
-
-- __drm_atomic_helper_crtc_destroy_state(crtc, state);
-+ drm_atomic_helper_crtc_destroy_state(crtc, state);
- }
-
- static const struct drm_crtc_funcs vc4_crtc_funcs = {
diff --git a/target/linux/brcm2708/patches-4.4/0526-x86-boot-Fix-kdump-cleanup-aborted-E820_PRAM-max_pfn.patch b/target/linux/brcm2708/patches-4.4/0526-x86-boot-Fix-kdump-cleanup-aborted-E820_PRAM-max_pfn.patch
deleted file mode 100644
index 87d3f66..0000000
--- a/target/linux/brcm2708/patches-4.4/0526-x86-boot-Fix-kdump-cleanup-aborted-E820_PRAM-max_pfn.patch
+++ /dev/null
@@ -1,60 +0,0 @@
-From b52304556d4944be31e2c6784a78c69a7a8288f1 Mon Sep 17 00:00:00 2001
-From: Dan Williams <dan.j.williams at intel.com>
-Date: Wed, 21 Sep 2016 12:50:45 -0700
-Subject: [PATCH] x86/boot: Fix kdump, cleanup aborted E820_PRAM max_pfn
- manipulation
-
-commit 917db484dc6a69969d317b3e57add4208a8d9d42 upstream.
-
-In commit:
-
- ec776ef6bbe1 ("x86/mm: Add support for the non-standard protected e820 type")
-
-Christoph references the original patch I wrote implementing pmem support.
-The intent of the 'max_pfn' changes in that commit were to enable persistent
-memory ranges to be covered by the struct page memmap by default.
-
-However, that approach was abandoned when Christoph ported the patches [1], and
-that functionality has since been replaced by devm_memremap_pages().
-
-In the meantime, this max_pfn manipulation is confusing kdump [2] that
-assumes that everything covered by the max_pfn is "System RAM". This
-results in kdump hanging or crashing.
-
- [1]: https://lists.01.org/pipermail/linux-nvdimm/2015-March/000348.html
- [2]: https://bugzilla.redhat.com/show_bug.cgi?id=1351098
-
-So fix it.
-
-Reported-by: Zhang Yi <yizhan at redhat.com>
-Reported-by: Jeff Moyer <jmoyer at redhat.com>
-Tested-by: Zhang Yi <yizhan at redhat.com>
-Signed-off-by: Dan Williams <dan.j.williams at intel.com>
-Reviewed-by: Jeff Moyer <jmoyer at redhat.com>
-Cc: Andrew Morton <akpm at linux-foundation.org>
-Cc: Boaz Harrosh <boaz at plexistor.com>
-Cc: Christoph Hellwig <hch at lst.de>
-Cc: Linus Torvalds <torvalds at linux-foundation.org>
-Cc: Peter Zijlstra <peterz at infradead.org>
-Cc: Ross Zwisler <ross.zwisler at linux.intel.com>
-Cc: Thomas Gleixner <tglx at linutronix.de>
-Cc: linux-nvdimm at lists.01.org
-Fixes: ec776ef6bbe1 ("x86/mm: Add support for the non-standard protected e820 type")
-Link: http://lkml.kernel.org/r/147448744538.34910.11287693517367139607.stgit@dwillia2-desk3.amr.corp.intel.com
-Signed-off-by: Ingo Molnar <mingo at kernel.org>
-Signed-off-by: Greg Kroah-Hartman <gregkh at linuxfoundation.org>
----
- arch/x86/kernel/e820.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/arch/x86/kernel/e820.c
-+++ b/arch/x86/kernel/e820.c
-@@ -347,7 +347,7 @@ int __init sanitize_e820_map(struct e820
- * continue building up new bios map based on this
- * information
- */
-- if (current_type != last_type || current_type == E820_PRAM) {
-+ if (current_type != last_type) {
- if (last_type != 0) {
- new_bios[new_bios_entry].size =
- change_point[chgidx]->addr - last_addr;
diff --git a/target/linux/brcm2708/patches-4.4/0527-Support-for-Blokas-Labs-pisound-board.patch b/target/linux/brcm2708/patches-4.4/0527-Support-for-Blokas-Labs-pisound-board.patch
deleted file mode 100644
index 2cdda63..0000000
--- a/target/linux/brcm2708/patches-4.4/0527-Support-for-Blokas-Labs-pisound-board.patch
+++ /dev/null
@@ -1,1208 +0,0 @@
-From e5068c05d531f02ee51d00df89a9b96ac434ca1f Mon Sep 17 00:00:00 2001
-From: gtrainavicius <gtrainavicius at users.noreply.github.com>
-Date: Sun, 23 Oct 2016 12:06:53 +0300
-Subject: [PATCH] Support for Blokas Labs pisound board
-
----
- .../devicetree/bindings/vendor-prefixes.txt | 1 +
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 6 +
- arch/arm/boot/dts/overlays/pisound-overlay.dts | 114 +++
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- sound/soc/bcm/Kconfig | 6 +
- sound/soc/bcm/Makefile | 2 +
- sound/soc/bcm/pisound.c | 987 +++++++++++++++++++++
- 9 files changed, 1119 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/pisound-overlay.dts
- create mode 100644 sound/soc/bcm/pisound.c
-
---- a/Documentation/devicetree/bindings/vendor-prefixes.txt
-+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
-@@ -33,6 +33,7 @@ auo AU Optronics Corporation
- avago Avago Technologies
- avic Shanghai AVIC Optoelectronics Co., Ltd.
- axis Axis Communications AB
-+blokaslabs Vilniaus Blokas UAB
- bosch Bosch Sensortec GmbH
- boundary Boundary Devices Inc.
- brcm Broadcom Corporation
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -62,6 +62,7 @@ dtbo-$(RPI_DT_OVERLAYS) += pi3-disable-b
- dtbo-$(RPI_DT_OVERLAYS) += pi3-miniuart-bt.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += piscreen.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += piscreen2r.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += pisound.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += pitft22.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += pitft28-capacitive.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += pitft28-resistive.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -808,6 +808,12 @@ Params: speed Display
- xohms Touchpanel sensitivity (X-plate resistance)
-
-
-+Name: pisound
-+Info: Configures the Blokas Labs pisound card
-+Load: dtoverlay=pisound
-+Params: <None>
-+
-+
- Name: pitft22
- Info: Adafruit PiTFT 2.2" screen
- Load: dtoverlay=pitft22,<param>=<val>
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/pisound-overlay.dts
-@@ -0,0 +1,114 @@
-+/*
-+ * pisound Linux kernel module.
-+ * Copyright (C) 2016 Vilniaus Blokas UAB, http://blokas.io/pisound
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * as published by the Free Software Foundation; version 2 of the
-+ * License.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA.
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+#include <dt-bindings/gpio/gpio.h>
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&sound>;
-+ __overlay__ {
-+ compatible = "blokaslabs,pisound";
-+ i2s-controller = <&i2s>;
-+ status = "okay";
-+
-+ pinctrl-0 = <&pisound_button_pins>;
-+
-+ osr-gpios =
-+ <&gpio 13 GPIO_ACTIVE_HIGH>,
-+ <&gpio 26 GPIO_ACTIVE_HIGH>,
-+ <&gpio 16 GPIO_ACTIVE_HIGH>;
-+
-+ reset-gpios =
-+ <&gpio 12 GPIO_ACTIVE_HIGH>,
-+ <&gpio 24 GPIO_ACTIVE_HIGH>;
-+
-+ data_available-gpios = <&gpio 25 GPIO_ACTIVE_HIGH>;
-+
-+ button-gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pisound_button_pins>;
-+
-+ pisound_button_pins: pisound_button_pins {
-+ brcm,pins = <17>;
-+ brcm,function = <0>; // Input
-+ brcm,pull = <2>; // Pull-Up
-+ };
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&i2s>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 3 {
-+ target-path = "/";
-+ __overlay__ {
-+ pcm5102a-codec {
-+ #sound-dai-cells = <0>;
-+ compatible = "ti,pcm5102a";
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ fragment at 4 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ status = "okay";
-+
-+ spidev at 0{
-+ status = "disabled";
-+ };
-+
-+ spidev at 1{
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ fragment at 5 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ pisound_spi: pisound_spi at 0{
-+ compatible = "blokaslabs,pisound-spi";
-+ reg = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&spi0_pins>;
-+ spi-max-frequency = <1000000>;
-+ };
-+ };
-+ };
-+};
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -880,6 +880,7 @@ CONFIG_SND_AUDIOINJECTOR_PI_SOUNDCARD=m
- CONFIG_SND_DIGIDAC1_SOUNDCARD=m
- CONFIG_SND_BCM2708_SOC_DIONAUDIO_LOCO=m
- CONFIG_SND_BCM2708_SOC_ALLO_PIANO_DAC=m
-+CONFIG_SND_PISOUND=m
- CONFIG_SND_SOC_ADAU1701=m
- CONFIG_SND_SOC_WM8804_I2C=m
- CONFIG_SND_SIMPLE_CARD=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -872,6 +872,7 @@ CONFIG_SND_AUDIOINJECTOR_PI_SOUNDCARD=m
- CONFIG_SND_DIGIDAC1_SOUNDCARD=m
- CONFIG_SND_BCM2708_SOC_DIONAUDIO_LOCO=m
- CONFIG_SND_BCM2708_SOC_ALLO_PIANO_DAC=m
-+CONFIG_SND_PISOUND=m
- CONFIG_SND_SOC_ADAU1701=m
- CONFIG_SND_SOC_WM8804_I2C=m
- CONFIG_SND_SIMPLE_CARD=m
---- a/sound/soc/bcm/Kconfig
-+++ b/sound/soc/bcm/Kconfig
-@@ -121,3 +121,9 @@ config SND_BCM2708_SOC_ALLO_PIANO_DAC
- select SND_SOC_PCM512x_I2C
- help
- Say Y or M if you want to add support for Allo Piano DAC.
-+
-+config SND_PISOUND
-+ tristate "Support for Blokas Labs pisound"
-+ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
-+ help
-+ Say Y or M if you want to add support for Blokas Labs pisound.
---- a/sound/soc/bcm/Makefile
-+++ b/sound/soc/bcm/Makefile
-@@ -20,6 +20,7 @@ snd-soc-audioinjector-pi-soundcard-objs
- snd-soc-digidac1-soundcard-objs := digidac1-soundcard.o
- snd-soc-dionaudio-loco-objs := dionaudio_loco.o
- snd-soc-allo-piano-dac-objs := allo-piano-dac.o
-+snd-soc-pisound-objs := pisound.o
-
- obj-$(CONFIG_SND_BCM2708_SOC_ADAU1977_ADC) += snd-soc-adau1977-adc.o
- obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DAC) += snd-soc-hifiberry-dac.o
-@@ -37,3 +38,4 @@ obj-$(CONFIG_SND_AUDIOINJECTOR_PI_SOUNDC
- obj-$(CONFIG_SND_DIGIDAC1_SOUNDCARD) += snd-soc-digidac1-soundcard.o
- obj-$(CONFIG_SND_BCM2708_SOC_DIONAUDIO_LOCO) += snd-soc-dionaudio-loco.o
- obj-$(CONFIG_SND_BCM2708_SOC_ALLO_PIANO_DAC) += snd-soc-allo-piano-dac.o
-+obj-$(CONFIG_SND_PISOUND) += snd-soc-pisound.o
---- /dev/null
-+++ b/sound/soc/bcm/pisound.c
-@@ -0,0 +1,987 @@
-+/*
-+ * pisound Linux kernel module.
-+ * Copyright (C) 2016 Vilniaus Blokas UAB, http://blokas.io/pisound
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * as published by the Free Software Foundation; version 2 of the
-+ * License.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
-+ * MA 02110-1301, USA.
-+ */
-+
-+#include <linux/init.h>
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+#include <linux/gpio.h>
-+#include <linux/kobject.h>
-+#include <linux/sysfs.h>
-+#include <linux/delay.h>
-+#include <linux/spi/spi.h>
-+#include <linux/interrupt.h>
-+#include <linux/kfifo.h>
-+
-+#include <sound/core.h>
-+#include <sound/pcm.h>
-+#include <sound/pcm_params.h>
-+#include <sound/soc.h>
-+#include <sound/jack.h>
-+#include <sound/rawmidi.h>
-+#include <sound/asequencer.h>
-+
-+static int pisnd_spi_init(struct device *dev);
-+static void pisnd_spi_uninit(void);
-+
-+static void pisnd_spi_send(uint8_t val);
-+static uint8_t pisnd_spi_recv(uint8_t *buffer, uint8_t length);
-+
-+typedef void (*pisnd_spi_recv_cb)(void *data);
-+static void pisnd_spi_set_callback(pisnd_spi_recv_cb cb, void *data);
-+
-+static const char *pisnd_spi_get_serial(void);
-+static const char *pisnd_spi_get_id(void);
-+static const char *pisnd_spi_get_version(void);
-+
-+static int pisnd_midi_init(struct snd_card *card);
-+static void pisnd_midi_uninit(void);
-+
-+#define PISOUND_LOG_PREFIX "pisound: "
-+
-+#ifdef DEBUG
-+# define printd(...) pr_alert(PISOUND_LOG_PREFIX __VA_ARGS__)
-+#else
-+# define printd(...) do {} while (0)
-+#endif
-+
-+#define printe(...) pr_err(PISOUND_LOG_PREFIX __VA_ARGS__)
-+#define printi(...) pr_info(PISOUND_LOG_PREFIX __VA_ARGS__)
-+
-+static int pisnd_output_open(struct snd_rawmidi_substream *substream)
-+{
-+ return 0;
-+}
-+
-+static int pisnd_output_close(struct snd_rawmidi_substream *substream)
-+{
-+ return 0;
-+}
-+
-+static void pisnd_output_trigger(
-+ struct snd_rawmidi_substream *substream,
-+ int up
-+ )
-+{
-+ uint8_t data;
-+
-+ if (!up)
-+ return;
-+
-+ while (snd_rawmidi_transmit_peek(substream, &data, 1)) {
-+ pisnd_spi_send(data);
-+ snd_rawmidi_transmit_ack(substream, 1);
-+ }
-+}
-+
-+static void pisnd_output_drain(struct snd_rawmidi_substream *substream)
-+{
-+ uint8_t data;
-+
-+ while (snd_rawmidi_transmit_peek(substream, &data, 1)) {
-+ pisnd_spi_send(data);
-+
-+ snd_rawmidi_transmit_ack(substream, 1);
-+ }
-+}
-+
-+static int pisnd_input_open(struct snd_rawmidi_substream *substream)
-+{
-+ return 0;
-+}
-+
-+static int pisnd_input_close(struct snd_rawmidi_substream *substream)
-+{
-+ return 0;
-+}
-+
-+static void pisnd_midi_recv_callback(void *substream)
-+{
-+ uint8_t data[128];
-+ uint8_t n = 0;
-+
-+ while ((n = pisnd_spi_recv(data, sizeof(data)))) {
-+ int res = snd_rawmidi_receive(substream, data, n);
-+ (void)res;
-+ printd("midi recv 0x%02x, res = %d\n", data, res);
-+ }
-+}
-+
-+static void pisnd_input_trigger(struct snd_rawmidi_substream *substream, int up)
-+{
-+ if (up) {
-+ pisnd_spi_set_callback(pisnd_midi_recv_callback, substream);
-+ pisnd_midi_recv_callback(substream);
-+ } else {
-+ pisnd_spi_set_callback(NULL, NULL);
-+ }
-+}
-+
-+static struct snd_rawmidi *g_rmidi;
-+
-+static struct snd_rawmidi_ops pisnd_output_ops = {
-+ .open = pisnd_output_open,
-+ .close = pisnd_output_close,
-+ .trigger = pisnd_output_trigger,
-+ .drain = pisnd_output_drain,
-+};
-+
-+static struct snd_rawmidi_ops pisnd_input_ops = {
-+ .open = pisnd_input_open,
-+ .close = pisnd_input_close,
-+ .trigger = pisnd_input_trigger,
-+};
-+
-+static void pisnd_get_port_info(
-+ struct snd_rawmidi *rmidi,
-+ int number,
-+ struct snd_seq_port_info *seq_port_info
-+ )
-+{
-+ seq_port_info->type =
-+ SNDRV_SEQ_PORT_TYPE_MIDI_GENERIC |
-+ SNDRV_SEQ_PORT_TYPE_HARDWARE |
-+ SNDRV_SEQ_PORT_TYPE_PORT;
-+ seq_port_info->midi_voices = 0;
-+}
-+
-+static struct snd_rawmidi_global_ops pisnd_global_ops = {
-+ .get_port_info = pisnd_get_port_info,
-+};
-+
-+static int pisnd_midi_init(struct snd_card *card)
-+{
-+ int err = snd_rawmidi_new(card, "pisound MIDI", 0, 1, 1, &g_rmidi);
-+
-+ if (err < 0) {
-+ printe("snd_rawmidi_new failed: %d\n", err);
-+ return err;
-+ }
-+
-+ strcpy(g_rmidi->name, "pisound MIDI ");
-+ strcat(g_rmidi->name, pisnd_spi_get_serial());
-+
-+ g_rmidi->info_flags =
-+ SNDRV_RAWMIDI_INFO_OUTPUT |
-+ SNDRV_RAWMIDI_INFO_INPUT |
-+ SNDRV_RAWMIDI_INFO_DUPLEX;
-+
-+ g_rmidi->ops = &pisnd_global_ops;
-+
-+ g_rmidi->private_data = (void *)0;
-+
-+ snd_rawmidi_set_ops(
-+ g_rmidi,
-+ SNDRV_RAWMIDI_STREAM_OUTPUT,
-+ &pisnd_output_ops
-+ );
-+
-+ snd_rawmidi_set_ops(
-+ g_rmidi,
-+ SNDRV_RAWMIDI_STREAM_INPUT,
-+ &pisnd_input_ops
-+ );
-+
-+ return 0;
-+}
-+
-+static void pisnd_midi_uninit(void)
-+{
-+}
-+
-+static void *g_recvData;
-+static pisnd_spi_recv_cb g_recvCallback;
-+
-+#define FIFO_SIZE 512
-+
-+static char g_serial_num[11];
-+static char g_id[25];
-+static char g_version[5];
-+
-+DEFINE_KFIFO(spi_fifo_in, uint8_t, FIFO_SIZE);
-+DEFINE_KFIFO(spi_fifo_out, uint8_t, FIFO_SIZE);
-+
-+static struct gpio_desc *data_available;
-+static struct gpio_desc *spi_reset;
-+
-+static struct spi_device *pisnd_spi_device;
-+
-+static struct workqueue_struct *pisnd_workqueue;
-+static struct work_struct pisnd_work_process;
-+
-+static void pisnd_work_handler(struct work_struct *work);
-+
-+static uint16_t spi_transfer16(uint16_t val);
-+
-+static int pisnd_init_workqueues(void)
-+{
-+ pisnd_workqueue = create_singlethread_workqueue("pisnd_workqueue");
-+ INIT_WORK(&pisnd_work_process, pisnd_work_handler);
-+
-+ return 0;
-+}
-+
-+static void pisnd_uninit_workqueues(void)
-+{
-+ flush_workqueue(pisnd_workqueue);
-+ destroy_workqueue(pisnd_workqueue);
-+
-+ pisnd_workqueue = NULL;
-+}
-+
-+static bool pisnd_spi_has_more(void)
-+{
-+ return gpiod_get_value(data_available);
-+}
-+
-+enum task_e {
-+ TASK_PROCESS = 0,
-+};
-+
-+static void pisnd_schedule_process(enum task_e task)
-+{
-+ if (pisnd_spi_device != NULL &&
-+ pisnd_workqueue != NULL &&
-+ !work_pending(&pisnd_work_process)
-+ ) {
-+ printd("schedule: has more = %d\n", pisnd_spi_has_more());
-+ if (task == TASK_PROCESS)
-+ queue_work(pisnd_workqueue, &pisnd_work_process);
-+ }
-+}
-+
-+static irqreturn_t data_available_interrupt_handler(int irq, void *dev_id)
-+{
-+ if (irq == gpiod_to_irq(data_available) && pisnd_spi_has_more()) {
-+ printd("schedule from irq\n");
-+ pisnd_schedule_process(TASK_PROCESS);
-+ }
-+
-+ return IRQ_HANDLED;
-+}
-+
-+static DEFINE_SPINLOCK(spilock);
-+static unsigned long spilockflags;
-+
-+static uint16_t spi_transfer16(uint16_t val)
-+{
-+ int err;
-+ struct spi_transfer transfer;
-+ struct spi_message msg;
-+ uint8_t txbuf[2];
-+ uint8_t rxbuf[2];
-+
-+ if (!pisnd_spi_device) {
-+ printe("pisnd_spi_device null, returning\n");
-+ return 0;
-+ }
-+
-+ spi_message_init(&msg);
-+
-+ memset(&transfer, 0, sizeof(transfer));
-+ memset(&rxbuf, 0, sizeof(rxbuf));
-+
-+ txbuf[0] = val >> 8;
-+ txbuf[1] = val & 0xff;
-+
-+ transfer.tx_buf = &txbuf;
-+ transfer.rx_buf = &rxbuf;
-+ transfer.len = sizeof(txbuf);
-+ transfer.speed_hz = 125000;
-+ transfer.delay_usecs = 100;
-+ spi_message_add_tail(&transfer, &msg);
-+
-+ spin_lock_irqsave(&spilock, spilockflags);
-+ err = spi_sync(pisnd_spi_device, &msg);
-+ spin_unlock_irqrestore(&spilock, spilockflags);
-+
-+ if (err < 0) {
-+ printe("spi_sync error %d\n", err);
-+ return 0;
-+ }
-+
-+ printd("received: %02x%02x\n", rxbuf[0], rxbuf[1]);
-+ printd("hasMore %d\n", pisnd_spi_has_more());
-+
-+ return (rxbuf[0] << 8) | rxbuf[1];
-+}
-+
-+static int spi_read_bytes(char *dst, size_t length, uint8_t *bytesRead)
-+{
-+ uint16_t rx;
-+ uint8_t size;
-+ uint8_t i;
-+
-+ memset(dst, 0, length);
-+ *bytesRead = 0;
-+
-+ rx = spi_transfer16(0);
-+ if (!(rx >> 8))
-+ return -EINVAL;
-+
-+ size = rx & 0xff;
-+
-+ if (size > length)
-+ return -EINVAL;
-+
-+ for (i = 0; i < size; ++i) {
-+ rx = spi_transfer16(0);
-+ if (!(rx >> 8))
-+ return -EINVAL;
-+
-+ dst[i] = rx & 0xff;
-+ }
-+
-+ *bytesRead = i;
-+
-+ return 0;
-+}
-+
-+static int spi_device_match(struct device *dev, void *data)
-+{
-+ struct spi_device *spi = container_of(dev, struct spi_device, dev);
-+
-+ printd(" %s %s %dkHz %d bits mode=0x%02X\n",
-+ spi->modalias, dev_name(dev), spi->max_speed_hz/1000,
-+ spi->bits_per_word, spi->mode);
-+
-+ if (strcmp("pisound-spi", spi->modalias) == 0) {
-+ printi("\tFound!\n");
-+ return 1;
-+ }
-+
-+ printe("\tNot found!\n");
-+ return 0;
-+}
-+
-+static struct spi_device *pisnd_spi_find_device(void)
-+{
-+ struct device *dev;
-+
-+ printi("Searching for spi device...\n");
-+ dev = bus_find_device(&spi_bus_type, NULL, NULL, spi_device_match);
-+ if (dev != NULL)
-+ return container_of(dev, struct spi_device, dev);
-+ else
-+ return NULL;
-+}
-+
-+static void pisnd_work_handler(struct work_struct *work)
-+{
-+ uint16_t rx;
-+ uint16_t tx;
-+ uint8_t val;
-+
-+ if (work == &pisnd_work_process) {
-+ if (pisnd_spi_device == NULL)
-+ return;
-+
-+ do {
-+ val = 0;
-+ tx = 0;
-+
-+ if (kfifo_get(&spi_fifo_out, &val))
-+ tx = 0x0f00 | val;
-+
-+ rx = spi_transfer16(tx);
-+
-+ if (rx & 0xff00) {
-+ kfifo_put(&spi_fifo_in, rx & 0xff);
-+ if (kfifo_len(&spi_fifo_in) > 16
-+ && g_recvCallback)
-+ g_recvCallback(g_recvData);
-+ }
-+ } while (rx != 0
-+ || !kfifo_is_empty(&spi_fifo_out)
-+ || pisnd_spi_has_more()
-+ );
-+
-+ if (!kfifo_is_empty(&spi_fifo_in) && g_recvCallback)
-+ g_recvCallback(g_recvData);
-+ }
-+}
-+
-+static int pisnd_spi_gpio_init(struct device *dev)
-+{
-+ spi_reset = gpiod_get_index(dev, "reset", 1, GPIOD_ASIS);
-+ data_available = gpiod_get_index(dev, "data_available", 0, GPIOD_ASIS);
-+
-+ gpiod_direction_output(spi_reset, 1);
-+ gpiod_direction_input(data_available);
-+
-+ /* Reset the slave. */
-+ gpiod_set_value(spi_reset, false);
-+ mdelay(1);
-+ gpiod_set_value(spi_reset, true);
-+
-+ /* Give time for spi slave to start. */
-+ mdelay(64);
-+
-+ return 0;
-+}
-+
-+static void pisnd_spi_gpio_uninit(void)
-+{
-+ gpiod_set_value(spi_reset, false);
-+ gpiod_put(spi_reset);
-+ spi_reset = NULL;
-+
-+ gpiod_put(data_available);
-+ data_available = NULL;
-+}
-+
-+static int pisnd_spi_gpio_irq_init(struct device *dev)
-+{
-+ return request_irq(
-+ gpiod_to_irq(data_available),
-+ data_available_interrupt_handler,
-+ IRQF_TIMER | IRQF_TRIGGER_RISING,
-+ "data_available_int",
-+ NULL
-+ );
-+}
-+
-+static void pisnd_spi_gpio_irq_uninit(void)
-+{
-+ free_irq(gpiod_to_irq(data_available), NULL);
-+}
-+
-+static int spi_read_info(void)
-+{
-+ uint16_t tmp;
-+ uint8_t count;
-+ uint8_t n;
-+ uint8_t i;
-+ uint8_t j;
-+ char buffer[257];
-+ int ret;
-+ char *p;
-+
-+ memset(g_serial_num, 0, sizeof(g_serial_num));
-+ memset(g_version, 0, sizeof(g_version));
-+ memset(g_id, 0, sizeof(g_id));
-+
-+ tmp = spi_transfer16(0);
-+
-+ if (!(tmp >> 8))
-+ return -EINVAL;
-+
-+ count = tmp & 0xff;
-+
-+ for (i = 0; i < count; ++i) {
-+ memset(buffer, 0, sizeof(buffer));
-+ ret = spi_read_bytes(buffer, sizeof(buffer)-1, &n);
-+
-+ if (ret < 0)
-+ return ret;
-+
-+ switch (i) {
-+ case 0:
-+ if (n != 2)
-+ return -EINVAL;
-+
-+ snprintf(
-+ g_version,
-+ sizeof(g_version),
-+ "%x.%02x",
-+ buffer[0],
-+ buffer[1]
-+ );
-+ break;
-+ case 1:
-+ if (n >= sizeof(g_serial_num))
-+ return -EINVAL;
-+
-+ memcpy(g_serial_num, buffer, sizeof(g_serial_num));
-+ break;
-+ case 2:
-+ {
-+ if (n >= sizeof(g_id))
-+ return -EINVAL;
-+
-+ p = g_id;
-+ for (j = 0; j < n; ++j)
-+ p += sprintf(p, "%02x", buffer[j]);
-+ }
-+ break;
-+ default:
-+ break;
-+ }
-+ }
-+
-+ return 0;
-+}
-+
-+static int pisnd_spi_init(struct device *dev)
-+{
-+ int ret;
-+ struct spi_device *spi;
-+
-+ memset(g_serial_num, 0, sizeof(g_serial_num));
-+ memset(g_id, 0, sizeof(g_id));
-+ memset(g_version, 0, sizeof(g_version));
-+
-+ spi = pisnd_spi_find_device();
-+
-+ if (spi != NULL) {
-+ printd("initializing spi!\n");
-+ pisnd_spi_device = spi;
-+ ret = spi_setup(pisnd_spi_device);
-+ } else {
-+ printe("SPI device not found, deferring!\n");
-+ return -EPROBE_DEFER;
-+ }
-+
-+ ret = pisnd_spi_gpio_init(dev);
-+
-+ if (ret < 0) {
-+ printe("SPI GPIO init failed: %d\n", ret);
-+ spi_dev_put(pisnd_spi_device);
-+ pisnd_spi_device = NULL;
-+ pisnd_spi_gpio_uninit();
-+ return ret;
-+ }
-+
-+ ret = spi_read_info();
-+
-+ if (ret < 0) {
-+ printe("Reading card info failed: %d\n", ret);
-+ spi_dev_put(pisnd_spi_device);
-+ pisnd_spi_device = NULL;
-+ pisnd_spi_gpio_uninit();
-+ return ret;
-+ }
-+
-+ /* Flash the LEDs. */
-+ spi_transfer16(0xf000);
-+
-+ ret = pisnd_spi_gpio_irq_init(dev);
-+ if (ret < 0) {
-+ printe("SPI irq request failed: %d\n", ret);
-+ spi_dev_put(pisnd_spi_device);
-+ pisnd_spi_device = NULL;
-+ pisnd_spi_gpio_irq_uninit();
-+ pisnd_spi_gpio_uninit();
-+ }
-+
-+ ret = pisnd_init_workqueues();
-+ if (ret != 0) {
-+ printe("Workqueue initialization failed: %d\n", ret);
-+ spi_dev_put(pisnd_spi_device);
-+ pisnd_spi_device = NULL;
-+ pisnd_spi_gpio_irq_uninit();
-+ pisnd_spi_gpio_uninit();
-+ pisnd_uninit_workqueues();
-+ return ret;
-+ }
-+
-+ if (pisnd_spi_has_more()) {
-+ printd("data is available, scheduling from init\n");
-+ pisnd_schedule_process(TASK_PROCESS);
-+ }
-+
-+ return 0;
-+}
-+
-+static void pisnd_spi_uninit(void)
-+{
-+ pisnd_uninit_workqueues();
-+
-+ spi_dev_put(pisnd_spi_device);
-+ pisnd_spi_device = NULL;
-+
-+ pisnd_spi_gpio_irq_uninit();
-+ pisnd_spi_gpio_uninit();
-+}
-+
-+static void pisnd_spi_send(uint8_t val)
-+{
-+ kfifo_put(&spi_fifo_out, val);
-+ printd("schedule from spi_send\n");
-+ pisnd_schedule_process(TASK_PROCESS);
-+}
-+
-+static uint8_t pisnd_spi_recv(uint8_t *buffer, uint8_t length)
-+{
-+ return kfifo_out(&spi_fifo_in, buffer, length);
-+}
-+
-+static void pisnd_spi_set_callback(pisnd_spi_recv_cb cb, void *data)
-+{
-+ g_recvData = data;
-+ g_recvCallback = cb;
-+}
-+
-+static const char *pisnd_spi_get_serial(void)
-+{
-+ if (strlen(g_serial_num))
-+ return g_serial_num;
-+
-+ return "";
-+}
-+
-+static const char *pisnd_spi_get_id(void)
-+{
-+ if (strlen(g_id))
-+ return g_id;
-+
-+ return "";
-+}
-+
-+static const char *pisnd_spi_get_version(void)
-+{
-+ if (strlen(g_version))
-+ return g_version;
-+
-+ return "";
-+}
-+
-+static const struct of_device_id pisound_of_match[] = {
-+ { .compatible = "blokaslabs,pisound", },
-+ { .compatible = "blokaslabs,pisound-spi", },
-+ {},
-+};
-+
-+static struct gpio_desc *osr0, *osr1, *osr2;
-+static struct gpio_desc *reset;
-+static struct gpio_desc *button;
-+
-+static int pisnd_hw_params(
-+ struct snd_pcm_substream *substream,
-+ struct snd_pcm_hw_params *params
-+ )
-+{
-+ printd("rate = %d\n", params_rate(params));
-+ printd("ch = %d\n", params_channels(params));
-+ printd("bits = %u\n",
-+ snd_pcm_format_physical_width(params_format(params)));
-+ printd("format = %d\n", params_format(params));
-+
-+ gpiod_set_value(reset, false);
-+
-+ switch (params_rate(params)) {
-+ case 48000:
-+ gpiod_set_value(osr0, true);
-+ gpiod_set_value(osr1, false);
-+ gpiod_set_value(osr2, false);
-+ break;
-+ case 96000:
-+ gpiod_set_value(osr0, true);
-+ gpiod_set_value(osr1, true);
-+ gpiod_set_value(osr2, false);
-+ break;
-+ case 192000:
-+ gpiod_set_value(osr0, true);
-+ gpiod_set_value(osr1, true);
-+ gpiod_set_value(osr2, true);
-+ break;
-+ default:
-+ printe("Unsupported rate %u!\n", params_rate(params));
-+ return -EINVAL;
-+ }
-+
-+ gpiod_set_value(reset, true);
-+
-+ return 0;
-+}
-+
-+static unsigned int rates[3] = {
-+ 48000, 96000, 192000
-+};
-+
-+static struct snd_pcm_hw_constraint_list constraints_rates = {
-+ .count = ARRAY_SIZE(rates),
-+ .list = rates,
-+ .mask = 0,
-+};
-+
-+static unsigned int sample_bits[] = {
-+ 24, 32
-+};
-+
-+static struct snd_pcm_hw_constraint_list constraints_sample_bits = {
-+ .count = ARRAY_SIZE(sample_bits),
-+ .list = sample_bits,
-+ .mask = 0,
-+};
-+
-+static int pisnd_startup(struct snd_pcm_substream *substream)
-+{
-+ int err = snd_pcm_hw_constraint_list(
-+ substream->runtime,
-+ 0,
-+ SNDRV_PCM_HW_PARAM_RATE,
-+ &constraints_rates
-+ );
-+
-+ if (err < 0)
-+ return err;
-+
-+ err = snd_pcm_hw_constraint_list(
-+ substream->runtime,
-+ 0,
-+ SNDRV_PCM_HW_PARAM_SAMPLE_BITS,
-+ &constraints_sample_bits
-+ );
-+
-+ if (err < 0)
-+ return err;
-+
-+ return 0;
-+}
-+
-+static struct snd_soc_ops pisnd_ops = {
-+ .startup = pisnd_startup,
-+ .hw_params = pisnd_hw_params,
-+};
-+
-+static struct snd_soc_dai_link pisnd_dai[] = {
-+ {
-+ .name = "pisound",
-+ .stream_name = "pisound",
-+ .cpu_dai_name = "bcm2708-i2s.0",
-+ .codec_dai_name = "snd-soc-dummy-dai",
-+ .platform_name = "bcm2708-i2s.0",
-+ .codec_name = "snd-soc-dummy",
-+ .dai_fmt =
-+ SND_SOC_DAIFMT_I2S |
-+ SND_SOC_DAIFMT_NB_NF |
-+ SND_SOC_DAIFMT_CBM_CFM,
-+ .ops = &pisnd_ops,
-+ },
-+};
-+
-+static int pisnd_card_probe(struct snd_soc_card *card)
-+{
-+ int err = pisnd_midi_init(card->snd_card);
-+
-+ if (err < 0)
-+ printe("pisnd_midi_init failed: %d\n", err);
-+
-+ return err;
-+}
-+
-+static int pisnd_card_remove(struct snd_soc_card *card)
-+{
-+ pisnd_midi_uninit();
-+ return 0;
-+}
-+
-+static struct snd_soc_card pisnd_card = {
-+ .name = "pisound",
-+ .owner = THIS_MODULE,
-+ .dai_link = pisnd_dai,
-+ .num_links = ARRAY_SIZE(pisnd_dai),
-+ .probe = pisnd_card_probe,
-+ .remove = pisnd_card_remove,
-+};
-+
-+static int pisnd_init_gpio(struct device *dev)
-+{
-+ osr0 = gpiod_get_index(dev, "osr", 0, GPIOD_ASIS);
-+ osr1 = gpiod_get_index(dev, "osr", 1, GPIOD_ASIS);
-+ osr2 = gpiod_get_index(dev, "osr", 2, GPIOD_ASIS);
-+
-+ reset = gpiod_get_index(dev, "reset", 0, GPIOD_ASIS);
-+
-+ button = gpiod_get_index(dev, "button", 0, GPIOD_ASIS);
-+
-+ gpiod_direction_output(osr0, 1);
-+ gpiod_direction_output(osr1, 1);
-+ gpiod_direction_output(osr2, 1);
-+ gpiod_direction_output(reset, 1);
-+
-+ gpiod_set_value(reset, false);
-+ gpiod_set_value(osr0, true);
-+ gpiod_set_value(osr1, false);
-+ gpiod_set_value(osr2, false);
-+ gpiod_set_value(reset, true);
-+
-+ gpiod_export(button, false);
-+
-+ return 0;
-+}
-+
-+static int pisnd_uninit_gpio(void)
-+{
-+ int i;
-+
-+ struct gpio_desc **gpios[] = {
-+ &osr0, &osr1, &osr2, &reset, &button,
-+ };
-+
-+ gpiod_unexport(button);
-+
-+ for (i = 0; i < ARRAY_SIZE(gpios); ++i) {
-+ if (*gpios[i] == NULL) {
-+ printd("weird, GPIO[%d] is NULL already\n", i);
-+ continue;
-+ }
-+
-+ gpiod_put(*gpios[i]);
-+ *gpios[i] = NULL;
-+ }
-+
-+ return 0;
-+}
-+
-+static struct kobject *pisnd_kobj;
-+
-+static ssize_t pisnd_serial_show(
-+ struct kobject *kobj,
-+ struct kobj_attribute *attr,
-+ char *buf
-+ )
-+{
-+ return sprintf(buf, "%s\n", pisnd_spi_get_serial());
-+}
-+
-+static ssize_t pisnd_id_show(
-+ struct kobject *kobj,
-+ struct kobj_attribute *attr,
-+ char *buf
-+ )
-+{
-+ return sprintf(buf, "%s\n", pisnd_spi_get_id());
-+}
-+
-+static ssize_t pisnd_version_show(
-+ struct kobject *kobj,
-+ struct kobj_attribute *attr,
-+ char *buf
-+ )
-+{
-+ return sprintf(buf, "%s\n", pisnd_spi_get_version());
-+}
-+
-+static struct kobj_attribute pisnd_serial_attribute =
-+ __ATTR(serial, 0644, pisnd_serial_show, NULL);
-+static struct kobj_attribute pisnd_id_attribute =
-+ __ATTR(id, 0644, pisnd_id_show, NULL);
-+static struct kobj_attribute pisnd_version_attribute =
-+ __ATTR(version, 0644, pisnd_version_show, NULL);
-+
-+static struct attribute *attrs[] = {
-+ &pisnd_serial_attribute.attr,
-+ &pisnd_id_attribute.attr,
-+ &pisnd_version_attribute.attr,
-+ NULL
-+};
-+
-+static struct attribute_group attr_group = { .attrs = attrs };
-+
-+static int pisnd_probe(struct platform_device *pdev)
-+{
-+ int ret = 0;
-+ int i;
-+
-+ ret = pisnd_spi_init(&pdev->dev);
-+ if (ret < 0) {
-+ printe("pisnd_spi_init failed: %d\n", ret);
-+ return ret;
-+ }
-+
-+ printi("Detected pisound card:\n");
-+ printi("\tSerial: %s\n", pisnd_spi_get_serial());
-+ printi("\tVersion: %s\n", pisnd_spi_get_version());
-+ printi("\tId: %s\n", pisnd_spi_get_id());
-+
-+ pisnd_kobj = kobject_create_and_add("pisound", kernel_kobj);
-+ if (!pisnd_kobj) {
-+ pisnd_spi_uninit();
-+ return -ENOMEM;
-+ }
-+
-+ ret = sysfs_create_group(pisnd_kobj, &attr_group);
-+ if (ret < 0) {
-+ pisnd_spi_uninit();
-+ kobject_put(pisnd_kobj);
-+ return -ENOMEM;
-+ }
-+
-+ pisnd_init_gpio(&pdev->dev);
-+ pisnd_card.dev = &pdev->dev;
-+
-+ if (pdev->dev.of_node) {
-+ struct device_node *i2s_node;
-+
-+ i2s_node = of_parse_phandle(
-+ pdev->dev.of_node,
-+ "i2s-controller",
-+ 0
-+ );
-+
-+ for (i = 0; i < pisnd_card.num_links; ++i) {
-+ struct snd_soc_dai_link *dai = &pisnd_dai[i];
-+
-+ if (i2s_node) {
-+ dai->cpu_dai_name = NULL;
-+ dai->cpu_of_node = i2s_node;
-+ dai->platform_name = NULL;
-+ dai->platform_of_node = i2s_node;
-+ dai->stream_name = pisnd_spi_get_serial();
-+ }
-+ }
-+ }
-+
-+ ret = snd_soc_register_card(&pisnd_card);
-+
-+ if (ret < 0) {
-+ printe("snd_soc_register_card() failed: %d\n", ret);
-+ pisnd_uninit_gpio();
-+ kobject_put(pisnd_kobj);
-+ pisnd_spi_uninit();
-+ }
-+
-+ return ret;
-+}
-+
-+static int pisnd_remove(struct platform_device *pdev)
-+{
-+ if (pisnd_kobj) {
-+ kobject_put(pisnd_kobj);
-+ pisnd_kobj = NULL;
-+ }
-+
-+ pisnd_spi_uninit();
-+
-+ /* Turn off */
-+ gpiod_set_value(reset, false);
-+ pisnd_uninit_gpio();
-+
-+ return snd_soc_unregister_card(&pisnd_card);
-+}
-+
-+MODULE_DEVICE_TABLE(of, pisound_of_match);
-+
-+static struct platform_driver pisnd_driver = {
-+ .driver = {
-+ .name = "snd-rpi-pisound",
-+ .owner = THIS_MODULE,
-+ .of_match_table = pisound_of_match,
-+ },
-+ .probe = pisnd_probe,
-+ .remove = pisnd_remove,
-+};
-+
-+module_platform_driver(pisnd_driver);
-+
-+MODULE_AUTHOR("Giedrius Trainavicius <giedrius at blokas.io>");
-+MODULE_DESCRIPTION("ASoC Driver for pisound, http://blokas.io/pisound");
-+MODULE_LICENSE("GPL v2");
diff --git a/target/linux/brcm2708/patches-4.4/0528-pisound-Fix-a-warning-in-DEBUG-builds.patch b/target/linux/brcm2708/patches-4.4/0528-pisound-Fix-a-warning-in-DEBUG-builds.patch
deleted file mode 100644
index ce757f5..0000000
--- a/target/linux/brcm2708/patches-4.4/0528-pisound-Fix-a-warning-in-DEBUG-builds.patch
+++ /dev/null
@@ -1,31 +0,0 @@
-From a87861c387cf8d0d6691c17be865495674852953 Mon Sep 17 00:00:00 2001
-From: Giedrius Trainavicius <giedrius at blokas.io>
-Date: Tue, 25 Oct 2016 01:47:20 +0300
-Subject: [PATCH] pisound: Fix a warning in DEBUG builds
-
-Also change a macro that enables debug level printing from DEBUG to
-PISOUND_DEBUG.
----
- sound/soc/bcm/pisound.c | 4 ++--
- 1 file changed, 2 insertions(+), 2 deletions(-)
-
---- a/sound/soc/bcm/pisound.c
-+++ b/sound/soc/bcm/pisound.c
-@@ -55,7 +55,7 @@ static void pisnd_midi_uninit(void);
-
- #define PISOUND_LOG_PREFIX "pisound: "
-
--#ifdef DEBUG
-+#ifdef PISOUND_DEBUG
- # define printd(...) pr_alert(PISOUND_LOG_PREFIX __VA_ARGS__)
- #else
- # define printd(...) do {} while (0)
-@@ -119,7 +119,7 @@ static void pisnd_midi_recv_callback(voi
- while ((n = pisnd_spi_recv(data, sizeof(data)))) {
- int res = snd_rawmidi_receive(substream, data, n);
- (void)res;
-- printd("midi recv 0x%02x, res = %d\n", data, res);
-+ printd("midi recv %u bytes, res = %d\n", n, res);
- }
- }
-
diff --git a/target/linux/brcm2708/patches-4.4/0529-config-Add-CONFIG_HTU21-module.patch b/target/linux/brcm2708/patches-4.4/0529-config-Add-CONFIG_HTU21-module.patch
deleted file mode 100644
index e017727..0000000
--- a/target/linux/brcm2708/patches-4.4/0529-config-Add-CONFIG_HTU21-module.patch
+++ /dev/null
@@ -1,30 +0,0 @@
-From b0aa1d105dfe38c99931ff08635d210e057137cc Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Tue, 1 Nov 2016 13:10:05 +0000
-Subject: [PATCH] config: Add CONFIG_HTU21 module
-
----
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 2 files changed, 2 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -1154,6 +1154,7 @@ CONFIG_IIO_KFIFO_BUF=m
- CONFIG_MCP320X=m
- CONFIG_MCP3422=m
- CONFIG_DHT11=m
-+CONFIG_HTU21=m
- CONFIG_PWM_BCM2835=m
- CONFIG_PWM_PCA9685=m
- CONFIG_RASPBERRYPI_FIRMWARE=y
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -1161,6 +1161,7 @@ CONFIG_IIO_KFIFO_BUF=m
- CONFIG_MCP320X=m
- CONFIG_MCP3422=m
- CONFIG_DHT11=m
-+CONFIG_HTU21=m
- CONFIG_PWM_BCM2835=m
- CONFIG_PWM_PCA9685=m
- CONFIG_RASPBERRYPI_FIRMWARE=y
diff --git a/target/linux/brcm2708/patches-4.4/0530-spi-bcm2835-Remove-unused-code.patch b/target/linux/brcm2708/patches-4.4/0530-spi-bcm2835-Remove-unused-code.patch
deleted file mode 100644
index 9979304..0000000
--- a/target/linux/brcm2708/patches-4.4/0530-spi-bcm2835-Remove-unused-code.patch
+++ /dev/null
@@ -1,93 +0,0 @@
-From 8e2a01dec1501b8832f1459213dcbd56b4e11307 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Tue, 8 Nov 2016 21:35:38 +0000
-Subject: [PATCH] spi-bcm2835: Remove unused code
-
----
- drivers/spi/spi-bcm2835.c | 66 -----------------------------------------------
- 1 file changed, 66 deletions(-)
-
---- a/drivers/spi/spi-bcm2835.c
-+++ b/drivers/spi/spi-bcm2835.c
-@@ -679,17 +679,8 @@ static void bcm2835_spi_set_cs(struct sp
- bcm2835_wr(bs, BCM2835_SPI_CS, cs);
- }
-
--static int chip_match_name(struct gpio_chip *chip, void *data)
--{
-- return !strcmp(chip->label, data);
--}
--
- static int bcm2835_spi_setup(struct spi_device *spi)
- {
-- int err;
-- struct gpio_chip *chip;
-- struct device_node *pins;
-- u32 pingroup_index;
- /*
- * sanity checking the native-chipselects
- */
-@@ -707,63 +698,6 @@ static int bcm2835_spi_setup(struct spi_
- return -EINVAL;
- }
-
--#if 0
-- /* now translate native cs to GPIO */
-- /* first look for chip select pins in the devices pin groups */
-- for (pingroup_index = 0;
-- (pins = of_parse_phandle(spi->master->dev.of_node,
-- "pinctrl-0",
-- pingroup_index)) != 0;
-- pingroup_index++) {
-- u32 pin;
-- u32 pin_index;
-- for (pin_index = 0;
-- of_property_read_u32_index(pins,
-- "brcm,pins",
-- pin_index,
-- &pin) == 0;
-- pin_index++) {
-- if (((spi->chip_select == 0) &&
-- ((pin == 8) || (pin == 36) || (pin == 46))) ||
-- ((spi->chip_select == 1) &&
-- ((pin == 7) || (pin == 35)))) {
-- spi->cs_gpio = pin;
-- break;
-- }
-- }
-- of_node_put(pins);
-- }
-- /* if that fails, assume GPIOs 7-11 are used */
-- if (!gpio_is_valid(spi->cs_gpio) ) {
-- /* get the gpio chip for the base */
-- chip = gpiochip_find("pinctrl-bcm2835", chip_match_name);
-- if (!chip)
-- return 0;
--
-- /* and calculate the real CS */
-- spi->cs_gpio = chip->base + 8 - spi->chip_select;
-- }
--
-- /* and set up the "mode" and level */
-- dev_info(&spi->dev, "setting up native-CS%i as GPIO %i\n",
-- spi->chip_select, spi->cs_gpio);
--
-- /* set up GPIO as output and pull to the correct level */
-- err = gpio_direction_output(spi->cs_gpio,
-- (spi->mode & SPI_CS_HIGH) ? 0 : 1);
-- if (err) {
-- dev_err(&spi->dev,
-- "could not set CS%i gpio %i as output: %i",
-- spi->chip_select, spi->cs_gpio, err);
-- return err;
-- }
-- /* the implementation of pinctrl-bcm2835 currently does not
-- * set the GPIO value when using gpio_direction_output
-- * so we are setting it here explicitly
-- */
-- gpio_set_value(spi->cs_gpio, (spi->mode & SPI_CS_HIGH) ? 0 : 1);
--#endif
--
- return 0;
- }
-
diff --git a/target/linux/brcm2708/patches-4.4/0531-bcm2708_fb-Add-ioctl-for-reading-gpu-memory-through-.patch b/target/linux/brcm2708/patches-4.4/0531-bcm2708_fb-Add-ioctl-for-reading-gpu-memory-through-.patch
deleted file mode 100644
index 9d0e527..0000000
--- a/target/linux/brcm2708/patches-4.4/0531-bcm2708_fb-Add-ioctl-for-reading-gpu-memory-through-.patch
+++ /dev/null
@@ -1,167 +0,0 @@
-From c6175951b8f95d9f2c30d00ec069cafd23c6f376 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Sat, 5 Nov 2016 14:14:43 +0000
-Subject: [PATCH] bcm2708_fb: Add ioctl for reading gpu memory through dma
-
----
- drivers/video/fbdev/bcm2708_fb.c | 109 +++++++++++++++++++++++++++++++++++++++
- include/uapi/linux/fb.h | 7 +++
- 2 files changed, 116 insertions(+)
-
---- a/drivers/video/fbdev/bcm2708_fb.c
-+++ b/drivers/video/fbdev/bcm2708_fb.c
-@@ -31,8 +31,10 @@
- #include <linux/console.h>
- #include <linux/debugfs.h>
- #include <asm/sizes.h>
-+#include <asm/uaccess.h>
- #include <linux/io.h>
- #include <linux/dma-mapping.h>
-+#include <linux/cred.h>
- #include <soc/bcm2835/raspberrypi-firmware.h>
-
- //#define BCM2708_FB_DEBUG
-@@ -429,6 +431,110 @@ static int bcm2708_fb_pan_display(struct
- return result;
- }
-
-+static void dma_memcpy(struct bcm2708_fb *fb, dma_addr_t dst, dma_addr_t src, int size)
-+{
-+ int burst_size = (fb->dma_chan == 0) ? 8 : 2;
-+ struct bcm2708_dma_cb *cb = fb->cb_base;
-+
-+ cb->info = BCM2708_DMA_BURST(burst_size) | BCM2708_DMA_S_WIDTH |
-+ BCM2708_DMA_S_INC | BCM2708_DMA_D_WIDTH |
-+ BCM2708_DMA_D_INC | BCM2708_DMA_TDMODE;
-+ cb->dst = dst;
-+ cb->src = src;
-+ cb->length = size;
-+ cb->stride = 0;
-+ cb->pad[0] = 0;
-+ cb->pad[1] = 0;
-+ cb->next = 0;
-+
-+ if (size < dma_busy_wait_threshold) {
-+ bcm_dma_start(fb->dma_chan_base, fb->cb_handle);
-+ bcm_dma_wait_idle(fb->dma_chan_base);
-+ } else {
-+ void __iomem *dma_chan = fb->dma_chan_base;
-+ cb->info |= BCM2708_DMA_INT_EN;
-+ bcm_dma_start(fb->dma_chan_base, fb->cb_handle);
-+ while (bcm_dma_is_busy(dma_chan)) {
-+ wait_event_interruptible(
-+ fb->dma_waitq,
-+ !bcm_dma_is_busy(dma_chan));
-+ }
-+ fb->stats.dma_irqs++;
-+ }
-+ fb->stats.dma_copies++;
-+}
-+
-+#define INTALIAS_NORMAL(x) ((x)&~0xc0000000) // address with no aliases
-+#define INTALIAS_L1L2_NONALLOCATING(x) (((x)&~0xc0000000)|0x80000000) // cache coherent but non-allocating in L1 and L2
-+
-+static long vc_mem_copy(struct bcm2708_fb *fb, unsigned long arg)
-+{
-+ struct fb_dmacopy ioparam;
-+ size_t size = PAGE_SIZE;
-+ u32 *buf = NULL;
-+ dma_addr_t bus_addr;
-+ long rc = 0;
-+ size_t offset;
-+ struct { u32 base, length; } gpu = {};
-+
-+ /* restrict this to root user */
-+ if (!uid_eq(current_euid(), GLOBAL_ROOT_UID))
-+ {
-+ rc = -EFAULT;
-+ goto out;
-+ }
-+
-+ /* Get the parameter data.
-+ */
-+ if (copy_from_user
-+ (&ioparam, (void *)arg, sizeof(ioparam)) != 0) {
-+ pr_err("[%s]: failed to copy-from-user\n",
-+ __func__);
-+ rc = -EFAULT;
-+ goto out;
-+ }
-+
-+ rc = rpi_firmware_property(fb->fw,
-+ RPI_FIRMWARE_GET_VC_MEMORY,
-+ &gpu, sizeof(gpu));
-+ if (rc != 0 || gpu.base == 0 || gpu.length == 0) {
-+ pr_err("[%s]: Unable to determine gpu memory %ld,%x,%x)\n", __func__, rc, gpu.base, gpu.length);
-+ return -EFAULT;
-+ }
-+
-+ if (INTALIAS_NORMAL(ioparam.src) < gpu.base || INTALIAS_NORMAL(ioparam.src) >= gpu.base + gpu.length) {
-+ pr_err("[%s]: Invalid memory access %x (%x-%x)", __func__, INTALIAS_NORMAL(ioparam.src), gpu.base, gpu.base + gpu.length);
-+ return -EFAULT;
-+ }
-+
-+ buf = dma_alloc_coherent(NULL, PAGE_ALIGN(size), &bus_addr,
-+ GFP_ATOMIC);
-+ if (!buf) {
-+ pr_err("[%s]: failed to dma_alloc_coherent(%d)\n",
-+ __func__, size);
-+ rc = -ENOMEM;
-+ goto out;
-+ }
-+
-+ for (offset = 0; offset < ioparam.length; offset += size) {
-+ size_t remaining = ioparam.length - offset;
-+ size_t s = min(size, remaining);
-+ unsigned char *p = (unsigned char *)ioparam.src + offset;
-+ unsigned char *q = (unsigned char *)ioparam.dst + offset;
-+ dma_memcpy(fb, (dma_addr_t)buf, INTALIAS_L1L2_NONALLOCATING((dma_addr_t)p), size);
-+ if (copy_to_user(q, buf, s) != 0) {
-+ pr_err("[%s]: failed to copy-to-user\n",
-+ __func__);
-+ rc = -EFAULT;
-+ goto out;
-+ }
-+ }
-+out:
-+ if (buf)
-+ dma_free_coherent(NULL, PAGE_ALIGN(size), buf, bus_addr);
-+ return rc;
-+}
-+
- static int bcm2708_ioctl(struct fb_info *info, unsigned int cmd, unsigned long arg)
- {
- struct bcm2708_fb *fb = to_bcm2708(info);
-@@ -441,6 +547,9 @@ static int bcm2708_ioctl(struct fb_info
- RPI_FIRMWARE_FRAMEBUFFER_SET_VSYNC,
- &dummy, sizeof(dummy));
- break;
-+ case FBIODMACOPY:
-+ ret = vc_mem_copy(fb, arg);
-+ break;
- default:
- dev_dbg(info->device, "Unknown ioctl 0x%x\n", cmd);
- return -ENOTTY;
---- a/include/uapi/linux/fb.h
-+++ b/include/uapi/linux/fb.h
-@@ -39,6 +39,7 @@
- * be concurrently added to the mainline kernel
- */
- #define FBIOCOPYAREA _IOW('z', 0x21, struct fb_copyarea)
-+#define FBIODMACOPY _IOW('z', 0x22, struct fb_dmacopy)
-
- #define FB_TYPE_PACKED_PIXELS 0 /* Packed Pixels */
- #define FB_TYPE_PLANES 1 /* Non interleaved planes */
-@@ -351,6 +352,12 @@ struct fb_copyarea {
- __u32 sy;
- };
-
-+struct fb_dmacopy {
-+ dma_addr_t dst;
-+ dma_addr_t src;
-+ __u32 length;
-+};
-+
- struct fb_fillrect {
- __u32 dx; /* screen-relative */
- __u32 dy;
diff --git a/target/linux/brcm2708/patches-4.4/0532-rpi-ft5406-Create-coherent-buffer-and-push-to-firmwa.patch b/target/linux/brcm2708/patches-4.4/0532-rpi-ft5406-Create-coherent-buffer-and-push-to-firmwa.patch
deleted file mode 100644
index 1f6dd34..0000000
--- a/target/linux/brcm2708/patches-4.4/0532-rpi-ft5406-Create-coherent-buffer-and-push-to-firmwa.patch
+++ /dev/null
@@ -1,244 +0,0 @@
-From a4d3f1962738d1d3e7a3185b17800f9823f2b4d2 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Fri, 11 Nov 2016 19:32:54 +0000
-Subject: [PATCH] rpi-ft5406: Create coherent buffer and push to firmware
-
----
- drivers/input/touchscreen/rpi-ft5406.c | 152 +++++++++++++++++++----------
- include/soc/bcm2835/raspberrypi-firmware.h | 1 +
- 2 files changed, 101 insertions(+), 52 deletions(-)
-
---- a/drivers/input/touchscreen/rpi-ft5406.c
-+++ b/drivers/input/touchscreen/rpi-ft5406.c
-@@ -21,6 +21,7 @@
- #include <linux/kthread.h>
- #include <linux/platform_device.h>
- #include <asm/io.h>
-+#include <linux/dma-mapping.h>
- #include <soc/bcm2835/raspberrypi-firmware.h>
-
- #define MAXIMUM_SUPPORTED_POINTS 10
-@@ -45,6 +46,7 @@ struct ft5406 {
- struct platform_device * pdev;
- struct input_dev * input_dev;
- void __iomem * ts_base;
-+ dma_addr_t bus_addr;
- struct ft5406_regs * regs;
- struct task_struct * thread;
- };
-@@ -117,18 +119,19 @@ static int ft5406_thread(void *arg)
-
- static int ft5406_probe(struct platform_device *pdev)
- {
-- int ret;
-- struct input_dev * input_dev = input_allocate_device();
-+ int err = 0;
-+ struct device *dev = &pdev->dev;
-+ struct device_node *np = dev->of_node;
- struct ft5406 * ts;
- struct device_node *fw_node;
- struct rpi_firmware *fw;
- u32 touchbuf;
-
-- dev_info(&pdev->dev, "Probing device\n");
-+ dev_info(dev, "Probing device\n");
-
-- fw_node = of_parse_phandle(pdev->dev.of_node, "firmware", 0);
-+ fw_node = of_parse_phandle(np, "firmware", 0);
- if (!fw_node) {
-- dev_err(&pdev->dev, "Missing firmware node\n");
-+ dev_err(dev, "Missing firmware node\n");
- return -ENOENT;
- }
-
-@@ -136,62 +139,88 @@ static int ft5406_probe(struct platform_
- if (!fw)
- return -EPROBE_DEFER;
-
-- ret = rpi_firmware_property(fw, RPI_FIRMWARE_FRAMEBUFFER_GET_TOUCHBUF,
-- &touchbuf, sizeof(touchbuf));
-- if (ret) {
-- dev_err(&pdev->dev, "Failed to get touch buffer\n");
-- return ret;
-+ ts = devm_kzalloc(dev, sizeof(struct ft5406), GFP_KERNEL);
-+ if (!ts) {
-+ dev_err(dev, "Failed to allocate memory\n");
-+ return -ENOMEM;
- }
-
-- if (!touchbuf) {
-- dev_err(&pdev->dev, "Touchscreen not detected\n");
-- return -ENODEV;
-+ ts->input_dev = input_allocate_device();
-+ if (!ts->input_dev) {
-+ dev_err(dev, "Failed to allocate input device\n");
-+ return -ENOMEM;
- }
-
-- dev_dbg(&pdev->dev, "Got TS buffer 0x%x\n", touchbuf);
-+ ts->ts_base = dma_zalloc_coherent(NULL, PAGE_SIZE, &ts->bus_addr, GFP_KERNEL);
-+ if (!ts->ts_base) {
-+ pr_err("[%s]: failed to dma_alloc_coherent(%ld)\n",
-+ __func__, PAGE_SIZE);
-+ err = -ENOMEM;
-+ goto out;
-+ }
-
-- ts = kzalloc(sizeof(struct ft5406), GFP_KERNEL);
-+ touchbuf = (u32)ts->bus_addr;
-+ err = rpi_firmware_property(fw, RPI_FIRMWARE_FRAMEBUFFER_SET_TOUCHBUF,
-+ &touchbuf, sizeof(touchbuf));
-
-- if (!ts || !input_dev) {
-- ret = -ENOMEM;
-- dev_err(&pdev->dev, "Failed to allocate memory\n");
-- return ret;
-+ if (err || touchbuf != 0) {
-+ dev_warn(dev, "Failed to set touchbuf, trying to get err:%x\n", err);
-+ dma_free_coherent(NULL, PAGE_SIZE, ts->ts_base, ts->bus_addr);
-+ ts->ts_base = 0;
-+ ts->bus_addr = 0;
-+ }
-+
-+ if (!ts->ts_base) {
-+ dev_warn(dev, "set failed, trying get (err:%d touchbuf:%x virt:%p bus:%x)\n", err, touchbuf, ts->ts_base, ts->bus_addr);
-+
-+ err = rpi_firmware_property(fw, RPI_FIRMWARE_FRAMEBUFFER_GET_TOUCHBUF,
-+ &touchbuf, sizeof(touchbuf));
-+ if (err) {
-+ dev_err(dev, "Failed to get touch buffer\n");
-+ goto out;
-+ }
-+
-+ if (!touchbuf) {
-+ dev_err(dev, "Touchscreen not detected\n");
-+ err = -ENODEV;
-+ goto out;
-+ }
-+
-+ dev_dbg(dev, "Got TS buffer 0x%x\n", touchbuf);
-+
-+ // mmap the physical memory
-+ touchbuf &= ~0xc0000000;
-+ ts->ts_base = ioremap(touchbuf, sizeof(*ts->regs));
-+ if (ts->ts_base == NULL)
-+ {
-+ dev_err(dev, "Failed to map physical address\n");
-+ err = -ENOMEM;
-+ goto out;
-+ }
- }
-- ts->input_dev = input_dev;
- platform_set_drvdata(pdev, ts);
- ts->pdev = pdev;
-
-- input_dev->name = "FT5406 memory based driver";
-+ ts->input_dev->name = "FT5406 memory based driver";
-
-- __set_bit(EV_KEY, input_dev->evbit);
-- __set_bit(EV_SYN, input_dev->evbit);
-- __set_bit(EV_ABS, input_dev->evbit);
-+ __set_bit(EV_KEY, ts->input_dev->evbit);
-+ __set_bit(EV_SYN, ts->input_dev->evbit);
-+ __set_bit(EV_ABS, ts->input_dev->evbit);
-
-- input_set_abs_params(input_dev, ABS_MT_POSITION_X, 0,
-+ input_set_abs_params(ts->input_dev, ABS_MT_POSITION_X, 0,
- SCREEN_WIDTH, 0, 0);
-- input_set_abs_params(input_dev, ABS_MT_POSITION_Y, 0,
-+ input_set_abs_params(ts->input_dev, ABS_MT_POSITION_Y, 0,
- SCREEN_HEIGHT, 0, 0);
-
-- input_mt_init_slots(input_dev, MAXIMUM_SUPPORTED_POINTS, INPUT_MT_DIRECT);
-+ input_mt_init_slots(ts->input_dev, MAXIMUM_SUPPORTED_POINTS, INPUT_MT_DIRECT);
-
-- input_set_drvdata(input_dev, ts);
-+ input_set_drvdata(ts->input_dev, ts);
-
-- ret = input_register_device(input_dev);
-- if (ret) {
-- dev_err(&pdev->dev, "could not register input device, %d\n",
-- ret);
-- return ret;
-- }
--
-- // mmap the physical memory
-- touchbuf &= ~0xc0000000;
-- ts->ts_base = ioremap(touchbuf, sizeof(*ts->regs));
-- if(ts->ts_base == NULL)
-- {
-- dev_err(&pdev->dev, "Failed to map physical address\n");
-- input_unregister_device(input_dev);
-- kzfree(ts);
-- return -ENOMEM;
-+ err = input_register_device(ts->input_dev);
-+ if (err) {
-+ dev_err(dev, "could not register input device, %d\n",
-+ err);
-+ goto out;
- }
-
- ts->regs = (struct ft5406_regs *) ts->ts_base;
-@@ -200,25 +229,44 @@ static int ft5406_probe(struct platform_
- ts->thread = kthread_run(ft5406_thread, ts, "ft5406");
- if(ts->thread == NULL)
- {
-- dev_err(&pdev->dev, "Failed to create kernel thread");
-- iounmap(ts->ts_base);
-- input_unregister_device(input_dev);
-- kzfree(ts);
-+ dev_err(dev, "Failed to create kernel thread");
-+ err = -ENOMEM;
-+ goto out;
- }
-
- return 0;
-+
-+out:
-+ if (ts->bus_addr) {
-+ dma_free_coherent(NULL, PAGE_SIZE, ts->ts_base, ts->bus_addr);
-+ ts->bus_addr = 0;
-+ ts->ts_base = NULL;
-+ } else if (ts->ts_base) {
-+ iounmap(ts->ts_base);
-+ ts->ts_base = NULL;
-+ }
-+ if (ts->input_dev) {
-+ input_unregister_device(ts->input_dev);
-+ ts->input_dev = NULL;
-+ }
-+ return err;
- }
-
- static int ft5406_remove(struct platform_device *pdev)
- {
-+ struct device *dev = &pdev->dev;
- struct ft5406 *ts = (struct ft5406 *) platform_get_drvdata(pdev);
-
-- dev_info(&pdev->dev, "Removing rpi-ft5406\n");
-+ dev_info(dev, "Removing rpi-ft5406\n");
-
- kthread_stop(ts->thread);
-- iounmap(ts->ts_base);
-- input_unregister_device(ts->input_dev);
-- kzfree(ts);
-+
-+ if (ts->bus_addr)
-+ dma_free_coherent(dev, PAGE_SIZE, ts->ts_base, ts->bus_addr);
-+ else if (ts->ts_base)
-+ iounmap(ts->ts_base);
-+ if (ts->input_dev)
-+ input_unregister_device(ts->input_dev);
-
- return 0;
- }
---- a/include/soc/bcm2835/raspberrypi-firmware.h
-+++ b/include/soc/bcm2835/raspberrypi-firmware.h
-@@ -117,6 +117,7 @@ enum rpi_firmware_property_tag {
- RPI_FIRMWARE_FRAMEBUFFER_SET_VIRTUAL_OFFSET = 0x00048009,
- RPI_FIRMWARE_FRAMEBUFFER_SET_OVERSCAN = 0x0004800a,
- RPI_FIRMWARE_FRAMEBUFFER_SET_PALETTE = 0x0004800b,
-+ RPI_FIRMWARE_FRAMEBUFFER_SET_TOUCHBUF = 0x0004801f,
- RPI_FIRMWARE_FRAMEBUFFER_SET_VSYNC = 0x0004800e,
- RPI_FIRMWARE_FRAMEBUFFER_SET_BACKLIGHT = 0x0004800f,
-
diff --git a/target/linux/brcm2708/patches-4.4/0533-brcmvirt_gpio-Create-coherent-buffer-and-push-to-fir.patch b/target/linux/brcm2708/patches-4.4/0533-brcmvirt_gpio-Create-coherent-buffer-and-push-to-fir.patch
deleted file mode 100644
index cc2951c..0000000
--- a/target/linux/brcm2708/patches-4.4/0533-brcmvirt_gpio-Create-coherent-buffer-and-push-to-fir.patch
+++ /dev/null
@@ -1,169 +0,0 @@
-From 3f948a5f5bb5c736fa051a98fffacc3200d0e40e Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Wed, 9 Nov 2016 22:42:39 +0000
-Subject: [PATCH] brcmvirt_gpio: Create coherent buffer and push to firmware
-
----
- drivers/gpio/gpio-bcm-virt.c | 88 +++++++++++++++++++++---------
- include/soc/bcm2835/raspberrypi-firmware.h | 1 +
- 2 files changed, 62 insertions(+), 27 deletions(-)
-
---- a/drivers/gpio/gpio-bcm-virt.c
-+++ b/drivers/gpio/gpio-bcm-virt.c
-@@ -15,6 +15,7 @@
- #include <linux/module.h>
- #include <linux/basic_mmio_gpio.h>
- #include <linux/platform_device.h>
-+#include <linux/dma-mapping.h>
- #include <soc/bcm2835/raspberrypi-firmware.h>
-
- #define MODULE_NAME "brcmvirt-gpio"
-@@ -26,6 +27,7 @@ struct brcmvirt_gpio {
- /* two packed 16-bit counts of enabled and disables
- Allows host to detect a brief enable that was missed */
- u32 enables_disables[NUM_GPIO];
-+ dma_addr_t bus_addr;
- };
-
- static int brcmvirt_gpio_dir_in(struct gpio_chip *gc, unsigned off)
-@@ -76,13 +78,13 @@ static void brcmvirt_gpio_set(struct gpi
-
- static int brcmvirt_gpio_probe(struct platform_device *pdev)
- {
-+ int err = 0;
- struct device *dev = &pdev->dev;
- struct device_node *np = dev->of_node;
- struct device_node *fw_node;
- struct rpi_firmware *fw;
- struct brcmvirt_gpio *ucb;
- u32 gpiovirtbuf;
-- int err = 0;
-
- fw_node = of_parse_phandle(np, "firmware", 0);
- if (!fw_node) {
-@@ -94,35 +96,56 @@ static int brcmvirt_gpio_probe(struct pl
- if (!fw)
- return -EPROBE_DEFER;
-
-- err = rpi_firmware_property(fw, RPI_FIRMWARE_FRAMEBUFFER_GET_GPIOVIRTBUF,
-- &gpiovirtbuf, sizeof(gpiovirtbuf));
--
-- if (err) {
-- dev_err(dev, "Failed to get gpiovirtbuf\n");
-- goto err;
-- }
--
-- if (!gpiovirtbuf) {
-- dev_err(dev, "No virtgpio buffer\n");
-- err = -ENOENT;
-- goto err;
-- }
--
- ucb = devm_kzalloc(dev, sizeof *ucb, GFP_KERNEL);
- if (!ucb) {
- err = -EINVAL;
-- goto err;
-+ goto out;
- }
-
-- // mmap the physical memory
-- gpiovirtbuf &= ~0xc0000000;
-- ucb->ts_base = ioremap(gpiovirtbuf, 4096);
-- if (ucb->ts_base == NULL) {
-- dev_err(dev, "Failed to map physical address\n");
-- err = -ENOENT;
-- goto err;
-+ ucb->ts_base = dma_zalloc_coherent(NULL, PAGE_SIZE, &ucb->bus_addr, GFP_KERNEL);
-+ if (!ucb->ts_base) {
-+ pr_err("[%s]: failed to dma_alloc_coherent(%ld)\n",
-+ __func__, PAGE_SIZE);
-+ err = -ENOMEM;
-+ goto out;
- }
-
-+ gpiovirtbuf = (u32)ucb->bus_addr;
-+ err = rpi_firmware_property(fw, RPI_FIRMWARE_FRAMEBUFFER_SET_GPIOVIRTBUF,
-+ &gpiovirtbuf, sizeof(gpiovirtbuf));
-+
-+ if (err || gpiovirtbuf != 0) {
-+ dev_warn(dev, "Failed to set gpiovirtbuf, trying to get err:%x\n", err);
-+ dma_free_coherent(NULL, PAGE_SIZE, ucb->ts_base, ucb->bus_addr);
-+ ucb->ts_base = 0;
-+ ucb->bus_addr = 0;
-+ }
-+
-+ if (!ucb->ts_base) {
-+ err = rpi_firmware_property(fw, RPI_FIRMWARE_FRAMEBUFFER_GET_GPIOVIRTBUF,
-+ &gpiovirtbuf, sizeof(gpiovirtbuf));
-+
-+ if (err) {
-+ dev_err(dev, "Failed to get gpiovirtbuf\n");
-+ goto out;
-+ }
-+
-+ if (!gpiovirtbuf) {
-+ dev_err(dev, "No virtgpio buffer\n");
-+ err = -ENOENT;
-+ goto out;
-+ }
-+
-+ // mmap the physical memory
-+ gpiovirtbuf &= ~0xc0000000;
-+ ucb->ts_base = ioremap(gpiovirtbuf, 4096);
-+ if (ucb->ts_base == NULL) {
-+ dev_err(dev, "Failed to map physical address\n");
-+ err = -ENOENT;
-+ goto out;
-+ }
-+ ucb->bus_addr = 0;
-+ }
- ucb->gc.label = MODULE_NAME;
- ucb->gc.owner = THIS_MODULE;
- ucb->gc.dev = dev;
-@@ -138,13 +161,21 @@ static int brcmvirt_gpio_probe(struct pl
-
- err = gpiochip_add(&ucb->gc);
- if (err)
-- goto err;
-+ goto out;
-
- platform_set_drvdata(pdev, ucb);
-
--err:
-+ return 0;
-+out:
-+ if (ucb->bus_addr) {
-+ dma_free_coherent(NULL, PAGE_SIZE, ucb->ts_base, ucb->bus_addr);
-+ ucb->bus_addr = 0;
-+ ucb->ts_base = NULL;
-+ } else if (ucb->ts_base) {
-+ iounmap(ucb->ts_base);
-+ ucb->ts_base = NULL;
-+ }
- return err;
--
- }
-
- static int brcmvirt_gpio_remove(struct platform_device *pdev)
-@@ -153,7 +184,10 @@ static int brcmvirt_gpio_remove(struct p
- struct brcmvirt_gpio *ucb = platform_get_drvdata(pdev);
-
- gpiochip_remove(&ucb->gc);
-- iounmap(ucb->ts_base);
-+ if (ucb->bus_addr)
-+ dma_free_coherent(NULL, PAGE_SIZE, ucb->ts_base, ucb->bus_addr);
-+ else if (ucb->ts_base)
-+ iounmap(ucb->ts_base);
- return err;
- }
-
---- a/include/soc/bcm2835/raspberrypi-firmware.h
-+++ b/include/soc/bcm2835/raspberrypi-firmware.h
-@@ -118,6 +118,7 @@ enum rpi_firmware_property_tag {
- RPI_FIRMWARE_FRAMEBUFFER_SET_OVERSCAN = 0x0004800a,
- RPI_FIRMWARE_FRAMEBUFFER_SET_PALETTE = 0x0004800b,
- RPI_FIRMWARE_FRAMEBUFFER_SET_TOUCHBUF = 0x0004801f,
-+ RPI_FIRMWARE_FRAMEBUFFER_SET_GPIOVIRTBUF = 0x00048020,
- RPI_FIRMWARE_FRAMEBUFFER_SET_VSYNC = 0x0004800e,
- RPI_FIRMWARE_FRAMEBUFFER_SET_BACKLIGHT = 0x0004800f,
-
diff --git a/target/linux/brcm2708/patches-4.4/0534-brcmvirt_gpio-Pass-device-structure-into-dma_zalloc_.patch b/target/linux/brcm2708/patches-4.4/0534-brcmvirt_gpio-Pass-device-structure-into-dma_zalloc_.patch
deleted file mode 100644
index 63eb897..0000000
--- a/target/linux/brcm2708/patches-4.4/0534-brcmvirt_gpio-Pass-device-structure-into-dma_zalloc_.patch
+++ /dev/null
@@ -1,53 +0,0 @@
-From c540f39ccf8c43d45d2f0a1604fbc920a65e1084 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Mon, 14 Nov 2016 17:46:54 +0000
-Subject: [PATCH] brcmvirt_gpio: Pass device structure into dma_zalloc_coherent
-
----
- drivers/gpio/gpio-bcm-virt.c | 9 +++++----
- 1 file changed, 5 insertions(+), 4 deletions(-)
-
---- a/drivers/gpio/gpio-bcm-virt.c
-+++ b/drivers/gpio/gpio-bcm-virt.c
-@@ -102,7 +102,7 @@ static int brcmvirt_gpio_probe(struct pl
- goto out;
- }
-
-- ucb->ts_base = dma_zalloc_coherent(NULL, PAGE_SIZE, &ucb->bus_addr, GFP_KERNEL);
-+ ucb->ts_base = dma_zalloc_coherent(dev, PAGE_SIZE, &ucb->bus_addr, GFP_KERNEL);
- if (!ucb->ts_base) {
- pr_err("[%s]: failed to dma_alloc_coherent(%ld)\n",
- __func__, PAGE_SIZE);
-@@ -116,7 +116,7 @@ static int brcmvirt_gpio_probe(struct pl
-
- if (err || gpiovirtbuf != 0) {
- dev_warn(dev, "Failed to set gpiovirtbuf, trying to get err:%x\n", err);
-- dma_free_coherent(NULL, PAGE_SIZE, ucb->ts_base, ucb->bus_addr);
-+ dma_free_coherent(dev, PAGE_SIZE, ucb->ts_base, ucb->bus_addr);
- ucb->ts_base = 0;
- ucb->bus_addr = 0;
- }
-@@ -168,7 +168,7 @@ static int brcmvirt_gpio_probe(struct pl
- return 0;
- out:
- if (ucb->bus_addr) {
-- dma_free_coherent(NULL, PAGE_SIZE, ucb->ts_base, ucb->bus_addr);
-+ dma_free_coherent(dev, PAGE_SIZE, ucb->ts_base, ucb->bus_addr);
- ucb->bus_addr = 0;
- ucb->ts_base = NULL;
- } else if (ucb->ts_base) {
-@@ -180,12 +180,13 @@ out:
-
- static int brcmvirt_gpio_remove(struct platform_device *pdev)
- {
-+ struct device *dev = &pdev->dev;
- int err = 0;
- struct brcmvirt_gpio *ucb = platform_get_drvdata(pdev);
-
- gpiochip_remove(&ucb->gc);
- if (ucb->bus_addr)
-- dma_free_coherent(NULL, PAGE_SIZE, ucb->ts_base, ucb->bus_addr);
-+ dma_free_coherent(dev, PAGE_SIZE, ucb->ts_base, ucb->bus_addr);
- else if (ucb->ts_base)
- iounmap(ucb->ts_base);
- return err;
diff --git a/target/linux/brcm2708/patches-4.4/0535-rpi-ft5406-Pass-device-structure-into-dma_zalloc_coh.patch b/target/linux/brcm2708/patches-4.4/0535-rpi-ft5406-Pass-device-structure-into-dma_zalloc_coh.patch
deleted file mode 100644
index bf2e426..0000000
--- a/target/linux/brcm2708/patches-4.4/0535-rpi-ft5406-Pass-device-structure-into-dma_zalloc_coh.patch
+++ /dev/null
@@ -1,38 +0,0 @@
-From cc96288e1ec40a79c16949fabbcfc3c857797c59 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Mon, 14 Nov 2016 20:14:21 +0000
-Subject: [PATCH] rpi-ft5406: Pass device structure into dma_zalloc_coherent
-
----
- drivers/input/touchscreen/rpi-ft5406.c | 6 +++---
- 1 file changed, 3 insertions(+), 3 deletions(-)
-
---- a/drivers/input/touchscreen/rpi-ft5406.c
-+++ b/drivers/input/touchscreen/rpi-ft5406.c
-@@ -151,7 +151,7 @@ static int ft5406_probe(struct platform_
- return -ENOMEM;
- }
-
-- ts->ts_base = dma_zalloc_coherent(NULL, PAGE_SIZE, &ts->bus_addr, GFP_KERNEL);
-+ ts->ts_base = dma_zalloc_coherent(dev, PAGE_SIZE, &ts->bus_addr, GFP_KERNEL);
- if (!ts->ts_base) {
- pr_err("[%s]: failed to dma_alloc_coherent(%ld)\n",
- __func__, PAGE_SIZE);
-@@ -165,7 +165,7 @@ static int ft5406_probe(struct platform_
-
- if (err || touchbuf != 0) {
- dev_warn(dev, "Failed to set touchbuf, trying to get err:%x\n", err);
-- dma_free_coherent(NULL, PAGE_SIZE, ts->ts_base, ts->bus_addr);
-+ dma_free_coherent(dev, PAGE_SIZE, ts->ts_base, ts->bus_addr);
- ts->ts_base = 0;
- ts->bus_addr = 0;
- }
-@@ -238,7 +238,7 @@ static int ft5406_probe(struct platform_
-
- out:
- if (ts->bus_addr) {
-- dma_free_coherent(NULL, PAGE_SIZE, ts->ts_base, ts->bus_addr);
-+ dma_free_coherent(dev, PAGE_SIZE, ts->ts_base, ts->bus_addr);
- ts->bus_addr = 0;
- ts->ts_base = NULL;
- } else if (ts->ts_base) {
diff --git a/target/linux/brcm2708/patches-4.4/0536-drm-vc4-Fix-a-couple-error-codes-in-vc4_cl_lookup_bo.patch b/target/linux/brcm2708/patches-4.4/0536-drm-vc4-Fix-a-couple-error-codes-in-vc4_cl_lookup_bo.patch
deleted file mode 100644
index 72aac75..0000000
--- a/target/linux/brcm2708/patches-4.4/0536-drm-vc4-Fix-a-couple-error-codes-in-vc4_cl_lookup_bo.patch
+++ /dev/null
@@ -1,39 +0,0 @@
-From 33286005886531c3f54e84b474b10f05f7c1771e Mon Sep 17 00:00:00 2001
-From: Dan Carpenter <dan.carpenter at oracle.com>
-Date: Thu, 13 Oct 2016 11:54:31 +0300
-Subject: [PATCH] drm/vc4: Fix a couple error codes in vc4_cl_lookup_bos()
-
-If the allocation fails the current code returns success. If
-copy_from_user() fails it returns the number of bytes remaining instead
-of -EFAULT.
-
-Fixes: d5b1a78a772f ("drm/vc4: Add support for drawing 3D frames.")
-Signed-off-by: Dan Carpenter <dan.carpenter at oracle.com>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit b2cdeb19f16ad984eb5bb9193f793d05a8101511)
----
- drivers/gpu/drm/vc4/vc4_gem.c | 9 +++++----
- 1 file changed, 5 insertions(+), 4 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -560,14 +560,15 @@ vc4_cl_lookup_bos(struct drm_device *dev
-
- handles = drm_malloc_ab(exec->bo_count, sizeof(uint32_t));
- if (!handles) {
-+ ret = -ENOMEM;
- DRM_ERROR("Failed to allocate incoming GEM handles\n");
- goto fail;
- }
-
-- ret = copy_from_user(handles,
-- (void __user *)(uintptr_t)args->bo_handles,
-- exec->bo_count * sizeof(uint32_t));
-- if (ret) {
-+ if (copy_from_user(handles,
-+ (void __user *)(uintptr_t)args->bo_handles,
-+ exec->bo_count * sizeof(uint32_t))) {
-+ ret = -EFAULT;
- DRM_ERROR("Failed to copy in GEM handles\n");
- goto fail;
- }
diff --git a/target/linux/brcm2708/patches-4.4/0537-drm-vc4-Fix-termination-of-the-initial-scan-for-bran.patch b/target/linux/brcm2708/patches-4.4/0537-drm-vc4-Fix-termination-of-the-initial-scan-for-bran.patch
deleted file mode 100644
index c470a20..0000000
--- a/target/linux/brcm2708/patches-4.4/0537-drm-vc4-Fix-termination-of-the-initial-scan-for-bran.patch
+++ /dev/null
@@ -1,68 +0,0 @@
-From 9e16ce3589c8db1e04dbaf901a6310b36ca52fc8 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Thu, 20 Oct 2016 16:48:12 -0700
-Subject: [PATCH] drm/vc4: Fix termination of the initial scan for branch
- targets.
-
-The loop is scanning until the original max_ip (size of the BO), but
-we want to not examine any code after the PROG_END's delay slots.
-There was a block trying to do that, except that we had some early
-continue statements if the signal wasn't a PROG_END or a BRANCH.
-
-The failure mode would be that a valid shader is rejected because some
-undefined memory after the PROG_END slots is parsed as a branch and
-the rest of its setup is illegal. I haven't seen this in the wild,
-but valgrind was complaining when about this up in the userland
-simulator mode.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 457e67a728696c4f8e6423c64e93def50530db9a)
----
- drivers/gpu/drm/vc4/vc4_validate_shaders.c | 19 ++++++++-----------
- 1 file changed, 8 insertions(+), 11 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_validate_shaders.c
-+++ b/drivers/gpu/drm/vc4/vc4_validate_shaders.c
-@@ -608,9 +608,7 @@ static bool
- vc4_validate_branches(struct vc4_shader_validation_state *validation_state)
- {
- uint32_t max_branch_target = 0;
-- bool found_shader_end = false;
- int ip;
-- int shader_end_ip = 0;
- int last_branch = -2;
-
- for (ip = 0; ip < validation_state->max_ip; ip++) {
-@@ -621,8 +619,13 @@ vc4_validate_branches(struct vc4_shader_
- uint32_t branch_target_ip;
-
- if (sig == QPU_SIG_PROG_END) {
-- shader_end_ip = ip;
-- found_shader_end = true;
-+ /* There are two delay slots after program end is
-+ * signaled that are still executed, then we're
-+ * finished. validation_state->max_ip is the
-+ * instruction after the last valid instruction in the
-+ * program.
-+ */
-+ validation_state->max_ip = ip + 3;
- continue;
- }
-
-@@ -676,15 +679,9 @@ vc4_validate_branches(struct vc4_shader_
- }
- set_bit(after_delay_ip, validation_state->branch_targets);
- max_branch_target = max(max_branch_target, after_delay_ip);
--
-- /* There are two delay slots after program end is signaled
-- * that are still executed, then we're finished.
-- */
-- if (found_shader_end && ip == shader_end_ip + 2)
-- break;
- }
-
-- if (max_branch_target > shader_end_ip) {
-+ if (max_branch_target > validation_state->max_ip - 3) {
- DRM_ERROR("Branch landed after QPU_SIG_PROG_END");
- return false;
- }
diff --git a/target/linux/brcm2708/patches-4.4/0538-drm-vc4-Add-support-for-rendering-with-ETC1-textures.patch b/target/linux/brcm2708/patches-4.4/0538-drm-vc4-Add-support-for-rendering-with-ETC1-textures.patch
deleted file mode 100644
index ecc77ee..0000000
--- a/target/linux/brcm2708/patches-4.4/0538-drm-vc4-Add-support-for-rendering-with-ETC1-textures.patch
+++ /dev/null
@@ -1,55 +0,0 @@
-From 19682684277e2e1c1eb60956891987790d5dc865 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Thu, 3 Nov 2016 18:53:10 -0700
-Subject: [PATCH] drm/vc4: Add support for rendering with ETC1 textures.
-
-The validation for it ends up being quite simple, but I hadn't got
-around to it before merging the driver. For backwards compatibility,
-we also need to add a flag so that the userspace GL driver can easily
-tell if the kernel will allow ETC1 textures (on an old kernel, it will
-continue to convert to RGBA8)
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 7154d76fedf549607afbc0d13db9aaf02da5cebf)
----
- drivers/gpu/drm/vc4/vc4_drv.c | 1 +
- drivers/gpu/drm/vc4/vc4_validate.c | 7 +++++++
- include/uapi/drm/vc4_drm.h | 1 +
- 3 files changed, 9 insertions(+)
-
---- a/drivers/gpu/drm/vc4/vc4_drv.c
-+++ b/drivers/gpu/drm/vc4/vc4_drv.c
-@@ -103,6 +103,7 @@ static int vc4_get_param_ioctl(struct dr
- pm_runtime_put(&vc4->v3d->pdev->dev);
- break;
- case DRM_VC4_PARAM_SUPPORTS_BRANCHES:
-+ case DRM_VC4_PARAM_SUPPORTS_ETC1:
- args->value = true;
- break;
- default:
---- a/drivers/gpu/drm/vc4/vc4_validate.c
-+++ b/drivers/gpu/drm/vc4/vc4_validate.c
-@@ -644,6 +644,13 @@ reloc_tex(struct vc4_exec_info *exec,
- cpp = 1;
- break;
- case VC4_TEXTURE_TYPE_ETC1:
-+ /* ETC1 is arranged as 64-bit blocks, where each block is 4x4
-+ * pixels.
-+ */
-+ cpp = 8;
-+ width = (width + 3) >> 2;
-+ height = (height + 3) >> 2;
-+ break;
- case VC4_TEXTURE_TYPE_BW1:
- case VC4_TEXTURE_TYPE_A4:
- case VC4_TEXTURE_TYPE_A1:
---- a/include/uapi/drm/vc4_drm.h
-+++ b/include/uapi/drm/vc4_drm.h
-@@ -286,6 +286,7 @@ struct drm_vc4_get_hang_state {
- #define DRM_VC4_PARAM_V3D_IDENT1 1
- #define DRM_VC4_PARAM_V3D_IDENT2 2
- #define DRM_VC4_PARAM_SUPPORTS_BRANCHES 3
-+#define DRM_VC4_PARAM_SUPPORTS_ETC1 4
-
- struct drm_vc4_get_param {
- __u32 param;
diff --git a/target/linux/brcm2708/patches-4.4/0539-drm-vc4-Use-runtime-autosuspend-to-avoid-thrashing-V.patch b/target/linux/brcm2708/patches-4.4/0539-drm-vc4-Use-runtime-autosuspend-to-avoid-thrashing-V.patch
deleted file mode 100644
index 5b5c818..0000000
--- a/target/linux/brcm2708/patches-4.4/0539-drm-vc4-Use-runtime-autosuspend-to-avoid-thrashing-V.patch
+++ /dev/null
@@ -1,78 +0,0 @@
-From df48efb6ddba732b0f0d2ac1ca3a997679500321 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Fri, 4 Nov 2016 15:58:38 -0700
-Subject: [PATCH] drm/vc4: Use runtime autosuspend to avoid thrashing V3D power
- state.
-
-The pm_runtime_put() we were using immediately released power on the
-device, which meant that we were generally turning the device off and
-on once per frame. In many profiles I've looked at, that added up to
-about 1% of CPU time, but this could get worse in the case of frequent
-rendering and readback (as may happen in X rendering). By keeping the
-device on until we've been idle for a couple of frames, we drop the
-overhead of runtime PM down to sub-.1%.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit 3a62234680d86efa0239665ed8a0e908f1aef147)
----
- drivers/gpu/drm/vc4/vc4_drv.c | 9 ++++++---
- drivers/gpu/drm/vc4/vc4_gem.c | 6 ++++--
- drivers/gpu/drm/vc4/vc4_v3d.c | 2 ++
- 3 files changed, 12 insertions(+), 5 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_drv.c
-+++ b/drivers/gpu/drm/vc4/vc4_drv.c
-@@ -86,21 +86,24 @@ static int vc4_get_param_ioctl(struct dr
- if (ret < 0)
- return ret;
- args->value = V3D_READ(V3D_IDENT0);
-- pm_runtime_put(&vc4->v3d->pdev->dev);
-+ pm_runtime_mark_last_busy(&vc4->v3d->pdev->dev);
-+ pm_runtime_put_autosuspend(&vc4->v3d->pdev->dev);
- break;
- case DRM_VC4_PARAM_V3D_IDENT1:
- ret = pm_runtime_get_sync(&vc4->v3d->pdev->dev);
- if (ret < 0)
- return ret;
- args->value = V3D_READ(V3D_IDENT1);
-- pm_runtime_put(&vc4->v3d->pdev->dev);
-+ pm_runtime_mark_last_busy(&vc4->v3d->pdev->dev);
-+ pm_runtime_put_autosuspend(&vc4->v3d->pdev->dev);
- break;
- case DRM_VC4_PARAM_V3D_IDENT2:
- ret = pm_runtime_get_sync(&vc4->v3d->pdev->dev);
- if (ret < 0)
- return ret;
- args->value = V3D_READ(V3D_IDENT2);
-- pm_runtime_put(&vc4->v3d->pdev->dev);
-+ pm_runtime_mark_last_busy(&vc4->v3d->pdev->dev);
-+ pm_runtime_put_autosuspend(&vc4->v3d->pdev->dev);
- break;
- case DRM_VC4_PARAM_SUPPORTS_BRANCHES:
- case DRM_VC4_PARAM_SUPPORTS_ETC1:
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -728,8 +728,10 @@ vc4_complete_exec(struct drm_device *dev
- mutex_unlock(&dev->struct_mutex);
-
- mutex_lock(&vc4->power_lock);
-- if (--vc4->power_refcount == 0)
-- pm_runtime_put(&vc4->v3d->pdev->dev);
-+ if (--vc4->power_refcount == 0) {
-+ pm_runtime_mark_last_busy(&vc4->v3d->pdev->dev);
-+ pm_runtime_put_autosuspend(&vc4->v3d->pdev->dev);
-+ }
- mutex_unlock(&vc4->power_lock);
-
- kfree(exec);
---- a/drivers/gpu/drm/vc4/vc4_v3d.c
-+++ b/drivers/gpu/drm/vc4/vc4_v3d.c
-@@ -222,6 +222,8 @@ static int vc4_v3d_bind(struct device *d
- return ret;
- }
-
-+ pm_runtime_use_autosuspend(dev);
-+ pm_runtime_set_autosuspend_delay(dev, 40); /* a little over 2 frames. */
- pm_runtime_enable(dev);
-
- return 0;
diff --git a/target/linux/brcm2708/patches-4.4/0540-drm-vc4-Use-drm_gem_object_unreference_unlocked.patch b/target/linux/brcm2708/patches-4.4/0540-drm-vc4-Use-drm_gem_object_unreference_unlocked.patch
deleted file mode 100644
index f3ff1c5..0000000
--- a/target/linux/brcm2708/patches-4.4/0540-drm-vc4-Use-drm_gem_object_unreference_unlocked.patch
+++ /dev/null
@@ -1,76 +0,0 @@
-From 26b1bf12a8ed92c1f97b3da7919056c888e1e49d Mon Sep 17 00:00:00 2001
-From: Daniel Vetter <daniel.vetter at ffwll.ch>
-Date: Mon, 30 May 2016 19:53:06 +0200
-Subject: [PATCH] drm/vc4: Use drm_gem_object_unreference_unlocked
-
-Since my last struct_mutex crusade someone escaped!
-
-This already has the advantage that for the common case when someone
-else holds a ref the unref won't even acquire dev->struct_mutex. And
-I'm working on code to allow drivers to completely opt-out of any and
-all dev->struct_mutex usage, but that only works if they use the
-_unlocked variants everywhere.
-
-v2: Drop comment too.
-
-v3: Drop the other comment too.
-
-Cc: Eric Anholt <eric at anholt.net>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Daniel Vetter <daniel.vetter at intel.com>
-Link: http://patchwork.freedesktop.org/patch/msgid/1464630800-30786-15-git-send-email-daniel.vetter@ffwll.ch
-(cherry picked from commit db3697295cf4da1356e3ec86761d464d6d013b48)
----
- drivers/gpu/drm/vc4/vc4_bo.c | 2 --
- drivers/gpu/drm/vc4/vc4_gem.c | 11 +++--------
- 2 files changed, 3 insertions(+), 10 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_bo.c
-+++ b/drivers/gpu/drm/vc4/vc4_bo.c
-@@ -311,8 +311,6 @@ static void vc4_bo_cache_free_old(struct
-
- /* Called on the last userspace/kernel unreference of the BO. Returns
- * it to the BO cache if possible, otherwise frees it.
-- *
-- * Note that this is called with the struct_mutex held.
- */
- void vc4_free_object(struct drm_gem_object *gem_bo)
- {
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -67,10 +67,8 @@ vc4_free_hang_state(struct drm_device *d
- {
- unsigned int i;
-
-- mutex_lock(&dev->struct_mutex);
- for (i = 0; i < state->user_state.bo_count; i++)
-- drm_gem_object_unreference(state->bo[i]);
-- mutex_unlock(&dev->struct_mutex);
-+ drm_gem_object_unreference_unlocked(state->bo[i]);
-
- kfree(state);
- }
-@@ -711,11 +709,9 @@ vc4_complete_exec(struct drm_device *dev
- struct vc4_dev *vc4 = to_vc4_dev(dev);
- unsigned i;
-
-- /* Need the struct lock for drm_gem_object_unreference(). */
-- mutex_lock(&dev->struct_mutex);
- if (exec->bo) {
- for (i = 0; i < exec->bo_count; i++)
-- drm_gem_object_unreference(&exec->bo[i]->base);
-+ drm_gem_object_unreference_unlocked(&exec->bo[i]->base);
- kfree(exec->bo);
- }
-
-@@ -723,9 +719,8 @@ vc4_complete_exec(struct drm_device *dev
- struct vc4_bo *bo = list_first_entry(&exec->unref_list,
- struct vc4_bo, unref_head);
- list_del(&bo->unref_head);
-- drm_gem_object_unreference(&bo->base.base);
-+ drm_gem_object_unreference_unlocked(&bo->base.base);
- }
-- mutex_unlock(&dev->struct_mutex);
-
- mutex_lock(&vc4->power_lock);
- if (--vc4->power_refcount == 0) {
diff --git a/target/linux/brcm2708/patches-4.4/0541-drm-vc4-Use-drm_malloc_ab-to-fix-large-rendering-job.patch b/target/linux/brcm2708/patches-4.4/0541-drm-vc4-Use-drm_malloc_ab-to-fix-large-rendering-job.patch
deleted file mode 100644
index dedc2b5..0000000
--- a/target/linux/brcm2708/patches-4.4/0541-drm-vc4-Use-drm_malloc_ab-to-fix-large-rendering-job.patch
+++ /dev/null
@@ -1,57 +0,0 @@
-From c3557e82a495ea8d0691f25883a9576a0a866fb9 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 19 Jul 2016 11:32:44 -0700
-Subject: [PATCH] drm/vc4: Use drm_malloc_ab to fix large rendering jobs.
-
-If you exceeded the size that kmalloc would return, you'd get a dmesg
-warning and a return from the job submit. We can handle much
-allocations with vmalloc, and drm_malloc_ab makes that decision.
-
-Fixes failure in piglit's scissor-many.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit ece7267dccf0e9e08cb6e8dc6b7ad2be9c4eb444)
----
- drivers/gpu/drm/vc4/vc4_gem.c | 10 +++++-----
- 1 file changed, 5 insertions(+), 5 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -549,8 +549,8 @@ vc4_cl_lookup_bos(struct drm_device *dev
- return -EINVAL;
- }
-
-- exec->bo = kcalloc(exec->bo_count, sizeof(struct drm_gem_cma_object *),
-- GFP_KERNEL);
-+ exec->bo = drm_calloc_large(exec->bo_count,
-+ sizeof(struct drm_gem_cma_object *));
- if (!exec->bo) {
- DRM_ERROR("Failed to allocate validated BO pointers\n");
- return -ENOMEM;
-@@ -624,7 +624,7 @@ vc4_get_bcl(struct drm_device *dev, stru
- * read the contents back for validation, and I think the
- * bo->vaddr is uncached access.
- */
-- temp = kmalloc(temp_size, GFP_KERNEL);
-+ temp = drm_malloc_ab(temp_size, 1);
- if (!temp) {
- DRM_ERROR("Failed to allocate storage for copying "
- "in bin/render CLs.\n");
-@@ -699,7 +699,7 @@ vc4_get_bcl(struct drm_device *dev, stru
- ret = vc4_wait_for_seqno(dev, exec->bin_dep_seqno, ~0ull, true);
-
- fail:
-- kfree(temp);
-+ drm_free_large(temp);
- return ret;
- }
-
-@@ -712,7 +712,7 @@ vc4_complete_exec(struct drm_device *dev
- if (exec->bo) {
- for (i = 0; i < exec->bo_count; i++)
- drm_gem_object_unreference_unlocked(&exec->bo[i]->base);
-- kfree(exec->bo);
-+ drm_free_large(exec->bo);
- }
-
- while (!list_empty(&exec->unref_list)) {
diff --git a/target/linux/brcm2708/patches-4.4/0542-drm-vc4-Free-hang-state-before-destroying-BO-cache.patch b/target/linux/brcm2708/patches-4.4/0542-drm-vc4-Free-hang-state-before-destroying-BO-cache.patch
deleted file mode 100644
index 1206fc9..0000000
--- a/target/linux/brcm2708/patches-4.4/0542-drm-vc4-Free-hang-state-before-destroying-BO-cache.patch
+++ /dev/null
@@ -1,29 +0,0 @@
-From 778bdac35c6979233dd6384dfba01eaa2a4b982b Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Tue, 26 Jul 2016 13:47:13 -0700
-Subject: [PATCH] drm/vc4: Free hang state before destroying BO cache.
-
-The BO cache will complain if BOs are still allocated when we try to
-destroy it (since freeing those BOs would try to hit the cache). You
-could hit this if you were to unload the module after a GPU hang.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Fixes: 214613656b51 ("drm/vc4: Add an interface for capturing the GPU state after a hang.")
-(cherry picked from commit def96527707e1978a0c88e75d13b082f51460d5c)
----
- drivers/gpu/drm/vc4/vc4_gem.c | 4 ++--
- 1 file changed, 2 insertions(+), 2 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_gem.c
-+++ b/drivers/gpu/drm/vc4/vc4_gem.c
-@@ -968,8 +968,8 @@ vc4_gem_destroy(struct drm_device *dev)
- vc4->overflow_mem = NULL;
- }
-
-- vc4_bo_cache_destroy(dev);
--
- if (vc4->hang_state)
- vc4_free_hang_state(dev, vc4->hang_state);
-+
-+ vc4_bo_cache_destroy(dev);
- }
diff --git a/target/linux/brcm2708/patches-4.4/0543-fixup-fb-Use-basic-types-for-dma-addresses-as-these-.patch b/target/linux/brcm2708/patches-4.4/0543-fixup-fb-Use-basic-types-for-dma-addresses-as-these-.patch
deleted file mode 100644
index b10aad7..0000000
--- a/target/linux/brcm2708/patches-4.4/0543-fixup-fb-Use-basic-types-for-dma-addresses-as-these-.patch
+++ /dev/null
@@ -1,23 +0,0 @@
-From 6eac03bfff5f5f587712829c05fc8b7e755ed482 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Mon, 14 Nov 2016 22:05:30 +0000
-Subject: [PATCH] fixup: fb: Use basic types for dma addresses as these are
- also included from user code
-
----
- include/uapi/linux/fb.h | 4 ++--
- 1 file changed, 2 insertions(+), 2 deletions(-)
-
---- a/include/uapi/linux/fb.h
-+++ b/include/uapi/linux/fb.h
-@@ -353,8 +353,8 @@ struct fb_copyarea {
- };
-
- struct fb_dmacopy {
-- dma_addr_t dst;
-- dma_addr_t src;
-+ void *dst;
-+ __u32 src;
- __u32 length;
- };
-
diff --git a/target/linux/brcm2708/patches-4.4/0544-fb-Use-correct-bus-address-for-dest-of-dma-memcpy.patch b/target/linux/brcm2708/patches-4.4/0544-fb-Use-correct-bus-address-for-dest-of-dma-memcpy.patch
deleted file mode 100644
index 8ab5b9f..0000000
--- a/target/linux/brcm2708/patches-4.4/0544-fb-Use-correct-bus-address-for-dest-of-dma-memcpy.patch
+++ /dev/null
@@ -1,29 +0,0 @@
-From c72b24faad8c4d0b1edeee61dac80dad502e5ce8 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Wed, 16 Nov 2016 21:17:27 +0000
-Subject: [PATCH] fb: Use correct bus address for dest of dma memcpy
-
----
- drivers/video/fbdev/bcm2708_fb.c | 4 ++--
- 1 file changed, 2 insertions(+), 2 deletions(-)
-
---- a/drivers/video/fbdev/bcm2708_fb.c
-+++ b/drivers/video/fbdev/bcm2708_fb.c
-@@ -438,7 +438,7 @@ static void dma_memcpy(struct bcm2708_fb
-
- cb->info = BCM2708_DMA_BURST(burst_size) | BCM2708_DMA_S_WIDTH |
- BCM2708_DMA_S_INC | BCM2708_DMA_D_WIDTH |
-- BCM2708_DMA_D_INC | BCM2708_DMA_TDMODE;
-+ BCM2708_DMA_D_INC;
- cb->dst = dst;
- cb->src = src;
- cb->length = size;
-@@ -521,7 +521,7 @@ static long vc_mem_copy(struct bcm2708_f
- size_t s = min(size, remaining);
- unsigned char *p = (unsigned char *)ioparam.src + offset;
- unsigned char *q = (unsigned char *)ioparam.dst + offset;
-- dma_memcpy(fb, (dma_addr_t)buf, INTALIAS_L1L2_NONALLOCATING((dma_addr_t)p), size);
-+ dma_memcpy(fb, bus_addr, INTALIAS_L1L2_NONALLOCATING((dma_addr_t)p), size);
- if (copy_to_user(q, buf, s) != 0) {
- pr_err("[%s]: failed to copy-to-user\n",
- __func__);
diff --git a/target/linux/brcm2708/patches-4.4/0545-drm-vc4-Add-fragment-shader-threading-support.patch b/target/linux/brcm2708/patches-4.4/0545-drm-vc4-Add-fragment-shader-threading-support.patch
deleted file mode 100644
index db469b3..0000000
--- a/target/linux/brcm2708/patches-4.4/0545-drm-vc4-Add-fragment-shader-threading-support.patch
+++ /dev/null
@@ -1,228 +0,0 @@
-From dcd19269dea9ee867deaf0fc5e5840525767c68e Mon Sep 17 00:00:00 2001
-From: Jonas Pfeil <pfeiljonas at gmx.de>
-Date: Tue, 8 Nov 2016 00:18:39 +0100
-Subject: [PATCH] drm/vc4: Add fragment shader threading support
-
-FS threading brings performance improvements of 0-20% in glmark2.
-
-The validation code checks for thread switch signals and ensures that
-the registers of the other thread are not touched, and that our clamps
-are not live across thread switches. It also checks that the
-threading and branching instructions do not interfere.
-
-(Original patch by Jonas, changes by anholt for style cleanup,
-removing validation the kernel doesn't need to do, and adding the flag
-for userspace).
-
-v2: Minor style fixes from checkpatch.
-
-Signed-off-by: Jonas Pfeil <pfeiljonas at gmx.de>
-Signed-off-by: Eric Anholt <eric at anholt.net>
-(cherry picked from commit c778cc5df944291dcdb1ca7a6bb781fbc22550c5)
----
- drivers/gpu/drm/vc4/vc4_drv.c | 1 +
- drivers/gpu/drm/vc4/vc4_drv.h | 2 +
- drivers/gpu/drm/vc4/vc4_validate.c | 17 +++++---
- drivers/gpu/drm/vc4/vc4_validate_shaders.c | 63 ++++++++++++++++++++++++++++++
- include/uapi/drm/vc4_drm.h | 1 +
- 5 files changed, 79 insertions(+), 5 deletions(-)
-
---- a/drivers/gpu/drm/vc4/vc4_drv.c
-+++ b/drivers/gpu/drm/vc4/vc4_drv.c
-@@ -107,6 +107,7 @@ static int vc4_get_param_ioctl(struct dr
- break;
- case DRM_VC4_PARAM_SUPPORTS_BRANCHES:
- case DRM_VC4_PARAM_SUPPORTS_ETC1:
-+ case DRM_VC4_PARAM_SUPPORTS_THREADED_FS:
- args->value = true;
- break;
- default:
---- a/drivers/gpu/drm/vc4/vc4_drv.h
-+++ b/drivers/gpu/drm/vc4/vc4_drv.h
-@@ -395,6 +395,8 @@ struct vc4_validated_shader_info {
-
- uint32_t num_uniform_addr_offsets;
- uint32_t *uniform_addr_offsets;
-+
-+ bool is_threaded;
- };
-
- /**
---- a/drivers/gpu/drm/vc4/vc4_validate.c
-+++ b/drivers/gpu/drm/vc4/vc4_validate.c
-@@ -789,11 +789,6 @@ validate_gl_shader_rec(struct drm_device
- exec->shader_rec_v += roundup(packet_size, 16);
- exec->shader_rec_size -= packet_size;
-
-- if (!(*(uint16_t *)pkt_u & VC4_SHADER_FLAG_FS_SINGLE_THREAD)) {
-- DRM_ERROR("Multi-threaded fragment shaders not supported.\n");
-- return -EINVAL;
-- }
--
- for (i = 0; i < shader_reloc_count; i++) {
- if (src_handles[i] > exec->bo_count) {
- DRM_ERROR("Shader handle %d too big\n", src_handles[i]);
-@@ -810,6 +805,18 @@ validate_gl_shader_rec(struct drm_device
- return -EINVAL;
- }
-
-+ if (((*(uint16_t *)pkt_u & VC4_SHADER_FLAG_FS_SINGLE_THREAD) == 0) !=
-+ to_vc4_bo(&bo[0]->base)->validated_shader->is_threaded) {
-+ DRM_ERROR("Thread mode of CL and FS do not match\n");
-+ return -EINVAL;
-+ }
-+
-+ if (to_vc4_bo(&bo[1]->base)->validated_shader->is_threaded ||
-+ to_vc4_bo(&bo[2]->base)->validated_shader->is_threaded) {
-+ DRM_ERROR("cs and vs cannot be threaded\n");
-+ return -EINVAL;
-+ }
-+
- for (i = 0; i < shader_reloc_count; i++) {
- struct vc4_validated_shader_info *validated_shader;
- uint32_t o = shader_reloc_offsets[i];
---- a/drivers/gpu/drm/vc4/vc4_validate_shaders.c
-+++ b/drivers/gpu/drm/vc4/vc4_validate_shaders.c
-@@ -83,6 +83,13 @@ struct vc4_shader_validation_state {
- * basic blocks.
- */
- bool needs_uniform_address_for_loop;
-+
-+ /* Set when we find an instruction writing the top half of the
-+ * register files. If we allowed writing the unusable regs in
-+ * a threaded shader, then the other shader running on our
-+ * QPU's clamp validation would be invalid.
-+ */
-+ bool all_registers_used;
- };
-
- static uint32_t
-@@ -119,6 +126,13 @@ raddr_add_a_to_live_reg_index(uint64_t i
- }
-
- static bool
-+live_reg_is_upper_half(uint32_t lri)
-+{
-+ return (lri >= 16 && lri < 32) ||
-+ (lri >= 32 + 16 && lri < 32 + 32);
-+}
-+
-+static bool
- is_tmu_submit(uint32_t waddr)
- {
- return (waddr == QPU_W_TMU0_S ||
-@@ -390,6 +404,9 @@ check_reg_write(struct vc4_validated_sha
- } else {
- validation_state->live_immediates[lri] = ~0;
- }
-+
-+ if (live_reg_is_upper_half(lri))
-+ validation_state->all_registers_used = true;
- }
-
- switch (waddr) {
-@@ -598,6 +615,11 @@ check_instruction_reads(struct vc4_valid
- }
- }
-
-+ if ((raddr_a >= 16 && raddr_a < 32) ||
-+ (raddr_b >= 16 && raddr_b < 32 && sig != QPU_SIG_SMALL_IMM)) {
-+ validation_state->all_registers_used = true;
-+ }
-+
- return true;
- }
-
-@@ -753,6 +775,7 @@ vc4_validate_shader(struct drm_gem_cma_o
- {
- bool found_shader_end = false;
- int shader_end_ip = 0;
-+ uint32_t last_thread_switch_ip = -3;
- uint32_t ip;
- struct vc4_validated_shader_info *validated_shader = NULL;
- struct vc4_shader_validation_state validation_state;
-@@ -785,6 +808,17 @@ vc4_validate_shader(struct drm_gem_cma_o
- if (!vc4_handle_branch_target(&validation_state))
- goto fail;
-
-+ if (ip == last_thread_switch_ip + 3) {
-+ /* Reset r0-r3 live clamp data */
-+ int i;
-+
-+ for (i = 64; i < LIVE_REG_COUNT; i++) {
-+ validation_state.live_min_clamp_offsets[i] = ~0;
-+ validation_state.live_max_clamp_regs[i] = false;
-+ validation_state.live_immediates[i] = ~0;
-+ }
-+ }
-+
- switch (sig) {
- case QPU_SIG_NONE:
- case QPU_SIG_WAIT_FOR_SCOREBOARD:
-@@ -794,6 +828,8 @@ vc4_validate_shader(struct drm_gem_cma_o
- case QPU_SIG_LOAD_TMU1:
- case QPU_SIG_PROG_END:
- case QPU_SIG_SMALL_IMM:
-+ case QPU_SIG_THREAD_SWITCH:
-+ case QPU_SIG_LAST_THREAD_SWITCH:
- if (!check_instruction_writes(validated_shader,
- &validation_state)) {
- DRM_ERROR("Bad write at ip %d\n", ip);
-@@ -809,6 +845,18 @@ vc4_validate_shader(struct drm_gem_cma_o
- shader_end_ip = ip;
- }
-
-+ if (sig == QPU_SIG_THREAD_SWITCH ||
-+ sig == QPU_SIG_LAST_THREAD_SWITCH) {
-+ validated_shader->is_threaded = true;
-+
-+ if (ip < last_thread_switch_ip + 3) {
-+ DRM_ERROR("Thread switch too soon after "
-+ "last switch at ip %d\n", ip);
-+ goto fail;
-+ }
-+ last_thread_switch_ip = ip;
-+ }
-+
- break;
-
- case QPU_SIG_LOAD_IMM:
-@@ -823,6 +871,13 @@ vc4_validate_shader(struct drm_gem_cma_o
- if (!check_branch(inst, validated_shader,
- &validation_state, ip))
- goto fail;
-+
-+ if (ip < last_thread_switch_ip + 3) {
-+ DRM_ERROR("Branch in thread switch at ip %d",
-+ ip);
-+ goto fail;
-+ }
-+
- break;
- default:
- DRM_ERROR("Unsupported QPU signal %d at "
-@@ -844,6 +899,14 @@ vc4_validate_shader(struct drm_gem_cma_o
- goto fail;
- }
-
-+ /* Might corrupt other thread */
-+ if (validated_shader->is_threaded &&
-+ validation_state.all_registers_used) {
-+ DRM_ERROR("Shader uses threading, but uses the upper "
-+ "half of the registers, too\n");
-+ goto fail;
-+ }
-+
- /* If we did a backwards branch and we haven't emitted a uniforms
- * reset since then, we still need the uniforms stream to have the
- * uniforms address available so that the backwards branch can do its
---- a/include/uapi/drm/vc4_drm.h
-+++ b/include/uapi/drm/vc4_drm.h
-@@ -287,6 +287,7 @@ struct drm_vc4_get_hang_state {
- #define DRM_VC4_PARAM_V3D_IDENT2 2
- #define DRM_VC4_PARAM_SUPPORTS_BRANCHES 3
- #define DRM_VC4_PARAM_SUPPORTS_ETC1 4
-+#define DRM_VC4_PARAM_SUPPORTS_THREADED_FS 5
-
- struct drm_vc4_get_param {
- __u32 param;
diff --git a/target/linux/brcm2708/patches-4.4/0546-fb-Use-struct-device-for-dma_alloc_coherent.patch b/target/linux/brcm2708/patches-4.4/0546-fb-Use-struct-device-for-dma_alloc_coherent.patch
deleted file mode 100644
index f9c9315..0000000
--- a/target/linux/brcm2708/patches-4.4/0546-fb-Use-struct-device-for-dma_alloc_coherent.patch
+++ /dev/null
@@ -1,29 +0,0 @@
-From 6661c06cfe9c5cc937ed662ed0463bd74e7d098e Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Thu, 17 Nov 2016 16:49:33 +0000
-Subject: [PATCH] fb: Use struct device for dma_alloc_coherent
-
----
- drivers/video/fbdev/bcm2708_fb.c | 4 ++--
- 1 file changed, 2 insertions(+), 2 deletions(-)
-
---- a/drivers/video/fbdev/bcm2708_fb.c
-+++ b/drivers/video/fbdev/bcm2708_fb.c
-@@ -507,7 +507,7 @@ static long vc_mem_copy(struct bcm2708_f
- return -EFAULT;
- }
-
-- buf = dma_alloc_coherent(NULL, PAGE_ALIGN(size), &bus_addr,
-+ buf = dma_alloc_coherent(fb->fb.device, PAGE_ALIGN(size), &bus_addr,
- GFP_ATOMIC);
- if (!buf) {
- pr_err("[%s]: failed to dma_alloc_coherent(%d)\n",
-@@ -531,7 +531,7 @@ static long vc_mem_copy(struct bcm2708_f
- }
- out:
- if (buf)
-- dma_free_coherent(NULL, PAGE_ALIGN(size), buf, bus_addr);
-+ dma_free_coherent(fb->fb.device, PAGE_ALIGN(size), buf, bus_addr);
- return rc;
- }
-
diff --git a/target/linux/brcm2708/patches-4.4/0547-ARM-dts-Visit-overlays-subdir-unconditionally.patch b/target/linux/brcm2708/patches-4.4/0547-ARM-dts-Visit-overlays-subdir-unconditionally.patch
deleted file mode 100644
index fa84561..0000000
--- a/target/linux/brcm2708/patches-4.4/0547-ARM-dts-Visit-overlays-subdir-unconditionally.patch
+++ /dev/null
@@ -1,34 +0,0 @@
-From 578a2d0ba3874bda5634737cd4184eeaa8749b37 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 18 Nov 2016 10:52:49 +0000
-Subject: [PATCH] ARM: dts: Visit overlays subdir unconditionally
-
-make clean processing occurs without loading the configuration, so the
-overlays subdir must be added unconditionally.
-
-See: https://github.com/raspberrypi/linux/issues/1723
----
- arch/arm/boot/dts/Makefile | 5 +----
- 1 file changed, 1 insertion(+), 4 deletions(-)
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -18,9 +18,6 @@ endif
- ifeq ($(CONFIG_ARCH_BCM2835),y)
- RPI_DT_OVERLAYS=y
- endif
--ifeq ($(RPI_DT_OVERLAYS),y)
-- dts-dirs += overlays
--endif
-
- dtb-$(CONFIG_ARCH_ALPINE) += \
- alpine-db.dtb
-@@ -809,7 +806,7 @@ dtstree := $(srctree)/$(src)
- dtb-$(CONFIG_OF_ALL_DTBS) := $(patsubst $(dtstree)/%.dts,%.dtb, $(wildcard $(dtstree)/*.dts))
-
- always := $(dtb-y)
--subdir-y := $(dts-dirs)
-+subdir-y := $(dts-dirs) overlays
- clean-files := *.dtb
-
- # Enable fixups to support overlays on BCM2708 platforms
diff --git a/target/linux/brcm2708/patches-4.4/0548-Audioinjector-Fix-bit-offsets-for-equal-volume-and-a.patch b/target/linux/brcm2708/patches-4.4/0548-Audioinjector-Fix-bit-offsets-for-equal-volume-and-a.patch
deleted file mode 100644
index c1b8a87..0000000
--- a/target/linux/brcm2708/patches-4.4/0548-Audioinjector-Fix-bit-offsets-for-equal-volume-and-a.patch
+++ /dev/null
@@ -1,55 +0,0 @@
-From c4a696183e90f0c3b3b857b6b876660707a60add Mon Sep 17 00:00:00 2001
-From: Matt Flax <flatmax at flatmax.org>
-Date: Sun, 20 Nov 2016 19:15:24 +1100
-Subject: [PATCH] [Audioinjector] Fix bit offsets for equal volume and add 8
- kHz operation (#1727)
-
-Applying to the audioinjector sound card only. This patch offsets channel
-2 correctly from the LR clock. This ensures that channel 2 doesn't loose
-any bits during capture. It also results in both channels 1 and 2 having
-the same volume. This commit also adds 8 kHz operation.
-
-Signed-off-by: Matt Flax <flatmax at flatmax.org>
----
- sound/soc/bcm/audioinjector-pi-soundcard.c | 16 +++++++++-------
- 1 file changed, 9 insertions(+), 7 deletions(-)
-
---- a/sound/soc/bcm/audioinjector-pi-soundcard.c
-+++ b/sound/soc/bcm/audioinjector-pi-soundcard.c
-@@ -30,7 +30,7 @@
- #include "../codecs/wm8731.h"
-
- static const unsigned int bcm2835_rates_12000000[] = {
-- 32000, 44100, 48000, 96000, 88200,
-+ 8000, 16000, 32000, 44100, 48000, 96000, 88200,
- };
-
- static struct snd_pcm_hw_constraint_list bcm2835_constraints_12000000 = {
-@@ -55,19 +55,21 @@ static int snd_audioinjector_pi_soundcar
-
- switch (params_rate(params)){
- case 8000:
-- return snd_soc_dai_set_bclk_ratio(cpu_dai, 1508);
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, 1);
-+ case 16000:
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, 750);
- case 32000:
-- return snd_soc_dai_set_bclk_ratio(cpu_dai, 378);
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, 375);
- case 44100:
-- return snd_soc_dai_set_bclk_ratio(cpu_dai, 274);
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, 272);
- case 48000:
-- return snd_soc_dai_set_bclk_ratio(cpu_dai, 252);
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, 250);
- case 88200:
- return snd_soc_dai_set_bclk_ratio(cpu_dai, 136);
- case 96000:
-- return snd_soc_dai_set_bclk_ratio(cpu_dai, 126);
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, 125);
- default:
-- return snd_soc_dai_set_bclk_ratio(cpu_dai, 126);
-+ return snd_soc_dai_set_bclk_ratio(cpu_dai, 125);
- }
- }
-
diff --git a/target/linux/brcm2708/patches-4.4/0549-config-Add-ABX80X-RTC-driver-and-overlay.patch b/target/linux/brcm2708/patches-4.4/0549-config-Add-ABX80X-RTC-driver-and-overlay.patch
deleted file mode 100644
index 98d32a8..0000000
--- a/target/linux/brcm2708/patches-4.4/0549-config-Add-ABX80X-RTC-driver-and-overlay.patch
+++ /dev/null
@@ -1,96 +0,0 @@
-From 34bea6c63c915333ea838b07438e93c28a8030e7 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Wed, 23 Nov 2016 14:19:40 +0000
-Subject: [PATCH] config: Add ABX80X RTC driver and overlay
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/overlays/README | 12 ++++++++++--
- arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts | 12 +++++++++++-
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 4 files changed, 23 insertions(+), 3 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -498,7 +498,11 @@ Params: addr I2C addr
- Name: i2c-rtc
- Info: Adds support for a number of I2C Real Time Clock devices
- Load: dtoverlay=i2c-rtc,<param>=<val>
--Params: ds1307 Select the DS1307 device
-+Params: abx80x Select one of the ABx80x family:
-+ AB0801, AB0803, AB0804, AB0805,
-+ AB1801, AB1803, AB1804, AB1805
-+
-+ ds1307 Select the DS1307 device
-
- ds1339 Select the DS1339 device
-
-@@ -514,7 +518,11 @@ Params: ds1307 Select t
-
- pcf8563 Select the PCF8563 device
-
-- trickle-resistor-ohms Resistor value for trickle charge (DS1339-only)
-+ trickle-diode-type Diode type for trickle charge - "standard" or
-+ "schottky" (ABx80x only)
-+
-+ trickle-resistor-ohms Resistor value for trickle charge (DS1339,
-+ ABx80x)
-
- wakeup-source Specify that the RTC can be used as a wakeup
- source
---- a/arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts
-@@ -12,6 +12,13 @@
- #size-cells = <0>;
- status = "okay";
-
-+ abx80x: abx80x at 69 {
-+ compatible = "abracon,abx80x";
-+ reg = <0x69>;
-+ abracon,tc-diode = "standard";
-+ abracon,tc-resistor = <0>;
-+ status = "disable";
-+ };
- ds1307: ds1307 at 68 {
- compatible = "maxim,ds1307";
- reg = <0x68>;
-@@ -56,6 +63,7 @@
- };
- };
- __overrides__ {
-+ abx80x = <&abx80x>,"status";
- ds1307 = <&ds1307>,"status";
- ds1339 = <&ds1339>,"status";
- ds3231 = <&ds3231>,"status";
-@@ -64,7 +72,9 @@
- pcf2127 = <&pcf2127>,"status";
- pcf8523 = <&pcf8523>,"status";
- pcf8563 = <&pcf8563>,"status";
-- trickle-resistor-ohms = <&ds1339>,"trickle-resistor-ohms:0";
-+ trickle-diode-type = <&abx80x>,"abracon,tc-diode";
-+ trickle-resistor-ohms = <&ds1339>,"trickle-resistor-ohms:0",
-+ <&abx80x>,"abracon,tc-resistor";
- wakeup-source = <&ds1339>,"wakeup-source?",
- <&ds3231>,"wakeup-source?",
- <&mcp7940x>,"wakeup-source?",
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -1060,6 +1060,7 @@ CONFIG_LEDS_TRIGGER_CAMERA=m
- CONFIG_LEDS_TRIGGER_INPUT=y
- CONFIG_RTC_CLASS=y
- # CONFIG_RTC_HCTOSYS is not set
-+CONFIG_RTC_DRV_ABX80X=m
- CONFIG_RTC_DRV_DS1307=m
- CONFIG_RTC_DRV_DS1374=m
- CONFIG_RTC_DRV_DS1672=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -1067,6 +1067,7 @@ CONFIG_LEDS_TRIGGER_CAMERA=m
- CONFIG_LEDS_TRIGGER_INPUT=y
- CONFIG_RTC_CLASS=y
- # CONFIG_RTC_HCTOSYS is not set
-+CONFIG_RTC_DRV_ABX80X=m
- CONFIG_RTC_DRV_DS1307=m
- CONFIG_RTC_DRV_DS1374=m
- CONFIG_RTC_DRV_DS1672=m
diff --git a/target/linux/brcm2708/patches-4.4/0550-config-Add-AK4554-audio-codec-driver.patch b/target/linux/brcm2708/patches-4.4/0550-config-Add-AK4554-audio-codec-driver.patch
deleted file mode 100644
index d0098f4..0000000
--- a/target/linux/brcm2708/patches-4.4/0550-config-Add-AK4554-audio-codec-driver.patch
+++ /dev/null
@@ -1,33 +0,0 @@
-From 7d18b4f336d99bccd63c15a1729cd44b965867a4 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Fri, 25 Nov 2016 15:01:15 +0000
-Subject: [PATCH] config: Add AK4554 audio codec driver
-
-See: https://github.com/raspberrypi/linux/issues/1730
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 2 files changed, 2 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -882,6 +882,7 @@ CONFIG_SND_BCM2708_SOC_DIONAUDIO_LOCO=m
- CONFIG_SND_BCM2708_SOC_ALLO_PIANO_DAC=m
- CONFIG_SND_PISOUND=m
- CONFIG_SND_SOC_ADAU1701=m
-+CONFIG_SND_SOC_AK4554=m
- CONFIG_SND_SOC_WM8804_I2C=m
- CONFIG_SND_SIMPLE_CARD=m
- CONFIG_SOUND_PRIME=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -874,6 +874,7 @@ CONFIG_SND_BCM2708_SOC_DIONAUDIO_LOCO=m
- CONFIG_SND_BCM2708_SOC_ALLO_PIANO_DAC=m
- CONFIG_SND_PISOUND=m
- CONFIG_SND_SOC_ADAU1701=m
-+CONFIG_SND_SOC_AK4554=m
- CONFIG_SND_SOC_WM8804_I2C=m
- CONFIG_SND_SIMPLE_CARD=m
- CONFIG_SOUND_PRIME=m
diff --git a/target/linux/brcm2708/patches-4.4/0551-kbuild-add-fno-PIE.patch b/target/linux/brcm2708/patches-4.4/0551-kbuild-add-fno-PIE.patch
deleted file mode 100644
index cb043b8..0000000
--- a/target/linux/brcm2708/patches-4.4/0551-kbuild-add-fno-PIE.patch
+++ /dev/null
@@ -1,40 +0,0 @@
-From ce348644b8dc5384764ed3fb91592d62523cbcb3 Mon Sep 17 00:00:00 2001
-From: Sebastian Andrzej Siewior <bigeasy at linutronix.de>
-Date: Fri, 4 Nov 2016 19:39:38 +0100
-Subject: [PATCH] kbuild: add -fno-PIE
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-commit 8ae94224c9d72fc4d9aaac93b2d7833cf46d7141 upstream.
-
-Debian started to build the gcc with -fPIE by default so the kernel
-build ends before it starts properly with:
-|kernel/bounds.c:1:0: error: code model kernel does not support PIC mode
-
-Also add to KBUILD_AFLAGS due to:
-
-|gcc -Wp,-MD,arch/x86/entry/vdso/vdso32/.note.o.d … -mfentry -DCC_USING_FENTRY … vdso/vdso32/note.S
-|arch/x86/entry/vdso/vdso32/note.S:1:0: sorry, unimplemented: -mfentry isn’t supported for 32-bit in combination with -fpic
-
-Tagging it stable so it is possible to compile recent stable kernels as
-well.
-
-Signed-off-by: Sebastian Andrzej Siewior <bigeasy at linutronix.de>
-Signed-off-by: Michal Marek <mmarek at suse.com>
-Signed-off-by: Greg Kroah-Hartman <gregkh at linuxfoundation.org>
----
- Makefile | 2 ++
- 1 file changed, 2 insertions(+)
-
---- a/Makefile
-+++ b/Makefile
-@@ -619,6 +619,8 @@ include arch/$(SRCARCH)/Makefile
- KBUILD_CFLAGS += $(call cc-option,-fno-delete-null-pointer-checks,)
- KBUILD_CFLAGS += $(call cc-disable-warning,maybe-uninitialized,)
- KBUILD_CFLAGS += $(call cc-disable-warning,frame-address,)
-+KBUILD_CFLAGS += $(call cc-option,-fno-PIE)
-+KBUILD_AFLAGS += $(call cc-option,-fno-PIE)
-
- ifdef CONFIG_CC_OPTIMIZE_FOR_SIZE
- KBUILD_CFLAGS += -Os $(EXTRA_OPTIMIZATION)
diff --git a/target/linux/brcm2708/patches-4.4/0552-kbuild-Steal-gcc-s-pie-from-the-very-beginning.patch b/target/linux/brcm2708/patches-4.4/0552-kbuild-Steal-gcc-s-pie-from-the-very-beginning.patch
deleted file mode 100644
index 36aafe8..0000000
--- a/target/linux/brcm2708/patches-4.4/0552-kbuild-Steal-gcc-s-pie-from-the-very-beginning.patch
+++ /dev/null
@@ -1,49 +0,0 @@
-From 8bb4bc0ec8fac19cc635e16d2e5a63dee2cd7f7b Mon Sep 17 00:00:00 2001
-From: Borislav Petkov <bp at suse.de>
-Date: Mon, 14 Nov 2016 19:41:31 +0100
-Subject: [PATCH] kbuild: Steal gcc's pie from the very beginning
-
-commit c6a385539175ebc603da53aafb7753d39089f32e upstream.
-
-So Sebastian turned off the PIE for kernel builds but that was too late
-- Kbuild.include already uses KBUILD_CFLAGS and trying to disable gcc
-options with, say cc-disable-warning, fails:
-
- gcc -D__KERNEL__ -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs
- ...
- -Wno-sign-compare -fno-asynchronous-unwind-tables -Wframe-address -c -x c /dev/null -o .31392.tmp
- /dev/null:1:0: error: code model kernel does not support PIC mode
-
-because that returns an error and we can't disable the warning. For
-example in this case:
-
-KBUILD_CFLAGS += $(call cc-disable-warning,frame-address,)
-
-which leads to gcc issuing all those warnings again.
-
-So let's turn off PIE/PIC at the earliest possible moment, when we
-declare KBUILD_CFLAGS so that cc-disable-warning picks it up too.
-
-Also, we need the $(call cc-option ...) because -fno-PIE is supported
-since gcc v3.4 and our lowest supported gcc version is 3.2 right now.
-
-Signed-off-by: Borislav Petkov <bp at suse.de>
-Cc: Ben Hutchings <ben at decadent.org.uk>
-Cc: Sebastian Andrzej Siewior <bigeasy at linutronix.de>
-Signed-off-by: Michal Marek <mmarek at suse.com>
-Signed-off-by: Greg Kroah-Hartman <gregkh at linuxfoundation.org>
----
- Makefile | 2 --
- 1 file changed, 2 deletions(-)
-
---- a/Makefile
-+++ b/Makefile
-@@ -619,8 +619,6 @@ include arch/$(SRCARCH)/Makefile
- KBUILD_CFLAGS += $(call cc-option,-fno-delete-null-pointer-checks,)
- KBUILD_CFLAGS += $(call cc-disable-warning,maybe-uninitialized,)
- KBUILD_CFLAGS += $(call cc-disable-warning,frame-address,)
--KBUILD_CFLAGS += $(call cc-option,-fno-PIE)
--KBUILD_AFLAGS += $(call cc-option,-fno-PIE)
-
- ifdef CONFIG_CC_OPTIMIZE_FOR_SIZE
- KBUILD_CFLAGS += -Os $(EXTRA_OPTIMIZATION)
diff --git a/target/linux/brcm2708/patches-4.4/0553-ARM-dts-Restore-dtbs_install-functionality.patch b/target/linux/brcm2708/patches-4.4/0553-ARM-dts-Restore-dtbs_install-functionality.patch
deleted file mode 100644
index 7962799..0000000
--- a/target/linux/brcm2708/patches-4.4/0553-ARM-dts-Restore-dtbs_install-functionality.patch
+++ /dev/null
@@ -1,25 +0,0 @@
-From 199489b0b5b2c25640a0e3a23834256cc6c9d536 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Sat, 26 Nov 2016 14:01:52 +0000
-Subject: [PATCH] ARM: dts: Restore dtbs_install functionality
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/Makefile | 3 ++-
- 1 file changed, 2 insertions(+), 1 deletion(-)
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -806,10 +806,11 @@ dtstree := $(srctree)/$(src)
- dtb-$(CONFIG_OF_ALL_DTBS) := $(patsubst $(dtstree)/%.dts,%.dtb, $(wildcard $(dtstree)/*.dts))
-
- always := $(dtb-y)
--subdir-y := $(dts-dirs) overlays
-+subdir-y := overlays
- clean-files := *.dtb
-
- # Enable fixups to support overlays on BCM2708 platforms
- ifeq ($(RPI_DT_OVERLAYS),y)
- DTC_FLAGS ?= -@ -H epapr
-+ dts-dirs += overlays
- endif
diff --git a/target/linux/brcm2708/patches-4.4/0554-BCM270X_DT-Update-UART0-clock-frequency.patch b/target/linux/brcm2708/patches-4.4/0554-BCM270X_DT-Update-UART0-clock-frequency.patch
deleted file mode 100644
index cdb83ff..0000000
--- a/target/linux/brcm2708/patches-4.4/0554-BCM270X_DT-Update-UART0-clock-frequency.patch
+++ /dev/null
@@ -1,29 +0,0 @@
-From 86533bf4f40251f9468a4f48775aa2cf1a37d6b7 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Sun, 27 Nov 2016 21:45:55 +0000
-Subject: [PATCH] BCM270X_DT: Update UART0 clock-frequency
-
-The Raspberry Pi firmware now sets the UART0 clock frequency to
-48MHz (was 3MHz), to allow for baudrates up to 3MHz. This value
-is overwritten by the firmware, but alternative loaders such
-as U-Boot ignore the firmware-provided DTB. And besides, the
-default ought to be correct.
-
-See: https://github.com/raspberrypi/linux/issues/1732
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/bcm2708_common.dtsi | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/arch/arm/boot/dts/bcm2708_common.dtsi
-+++ b/arch/arm/boot/dts/bcm2708_common.dtsi
-@@ -456,7 +456,7 @@
- reg = <2>;
- #clock-cells = <0>;
- clock-output-names = "uart0_pclk";
-- clock-frequency = <3000000>;
-+ clock-frequency = <48000000>;
- };
-
- clk_apb_p: clock at 3 {
diff --git a/target/linux/brcm2708/patches-4.4/0555-BCM2835-v4l2-Fix-a-conformance-test-failure.patch b/target/linux/brcm2708/patches-4.4/0555-BCM2835-v4l2-Fix-a-conformance-test-failure.patch
deleted file mode 100644
index ce809ff..0000000
--- a/target/linux/brcm2708/patches-4.4/0555-BCM2835-v4l2-Fix-a-conformance-test-failure.patch
+++ /dev/null
@@ -1,25 +0,0 @@
-From 8e038b685e146376ec5aa4b281c55cd3f854fccd Mon Sep 17 00:00:00 2001
-From: Dave Stevenson <6by9 at users.noreply.github.com>
-Date: Wed, 30 Nov 2016 20:17:14 +0000
-Subject: [PATCH] BCM2835-v4l2: Fix a conformance test failure
-
-Format ioctls:
- test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK
- warn: v4l2-test-formats.cpp(1195): S_PARM is supported but
- doesn't report V4L2_CAP_TIMEPERFRAME.
- fail: v4l2-test-formats.cpp(1118): node->has_frmintervals
- && !cap->capability
----
- drivers/media/platform/bcm2835/bcm2835-camera.c | 1 +
- 1 file changed, 1 insertion(+)
-
---- a/drivers/media/platform/bcm2835/bcm2835-camera.c
-+++ b/drivers/media/platform/bcm2835/bcm2835-camera.c
-@@ -1397,6 +1397,7 @@ static int vidioc_s_parm(struct file *fi
- dev->capture.timeperframe = tpf;
- parm->parm.capture.timeperframe = tpf;
- parm->parm.capture.readbuffers = 1;
-+ parm->parm.capture.capability = V4L2_CAP_TIMEPERFRAME;
-
- fps_param.num = 0; /* Select variable fps, and then use
- * FPS_RANGE to select the actual limits.
diff --git a/target/linux/brcm2708/patches-4.4/0556-BCM270X_DT-Add-overlay-for-enc28j60-on-SPI2.patch b/target/linux/brcm2708/patches-4.4/0556-BCM270X_DT-Add-overlay-for-enc28j60-on-SPI2.patch
deleted file mode 100644
index f36e993..0000000
--- a/target/linux/brcm2708/patches-4.4/0556-BCM270X_DT-Add-overlay-for-enc28j60-on-SPI2.patch
+++ /dev/null
@@ -1,97 +0,0 @@
-From 1d061a2bcabc8fb49de7db0094da863f8e7966e2 Mon Sep 17 00:00:00 2001
-From: Alan Yiding Wang <y2366wan at uwaterloo.ca>
-Date: Sat, 3 Dec 2016 23:22:02 -0500
-Subject: [PATCH] BCM270X_DT: Add overlay for enc28j60 on SPI2
-
-Works on SPI2 for compute module
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 10 ++++-
- .../boot/dts/overlays/enc28j60-spi2-overlay.dts | 47 ++++++++++++++++++++++
- 3 files changed, 57 insertions(+), 1 deletion(-)
- create mode 100644 arch/arm/boot/dts/overlays/enc28j60-spi2-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -28,6 +28,7 @@ dtbo-$(RPI_DT_OVERLAYS) += dpi24.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += dwc-otg.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += dwc2.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += enc28j60.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += enc28j60-spi2.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += gpio-ir.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += gpio-poweroff.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += hifiberry-amp.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -344,12 +344,20 @@ Params: dr_mode Dual rol
-
-
- Name: enc28j60
--Info: Overlay for the Microchip ENC28J60 Ethernet Controller (SPI)
-+Info: Overlay for the Microchip ENC28J60 Ethernet Controller on SPI0
- Load: dtoverlay=enc28j60,<param>=<val>
- Params: int_pin GPIO used for INT (default 25)
-
- speed SPI bus speed (default 12000000)
-
-+
-+Name: enc28j60-spi2
-+Info: Overlay for the Microchip ENC28J60 Ethernet Controller on SPI2
-+Load: dtoverlay=enc28j60-spi2,<param>=<val>
-+Params: int_pin GPIO used for INT (default 39)
-+
-+ speed SPI bus speed (default 12000000)
-+
-
- Name: gpio-ir
- Info: Use GPIO pin as rc-core style infrared receiver input. The rc-core-
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/enc28j60-spi2-overlay.dts
-@@ -0,0 +1,47 @@
-+// Overlay for the Microchip ENC28J60 Ethernet Controller - SPI2 Compute Module
-+// Interrupt pin: 39
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&spi2>;
-+ __overlay__ {
-+ /* needed to avoid dtc warning */
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ status = "okay";
-+
-+ eth1: enc28j60 at 0{
-+ compatible = "microchip,enc28j60";
-+ reg = <0>; /* CE0 */
-+ pinctrl-names = "default";
-+ pinctrl-0 = <ð1_pins>;
-+ interrupt-parent = <&gpio>;
-+ interrupts = <39 0x2>; /* falling edge */
-+ spi-max-frequency = <12000000>;
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&gpio>;
-+ __overlay__ {
-+ eth1_pins: eth1_pins {
-+ brcm,pins = <39>;
-+ brcm,function = <0>; /* in */
-+ brcm,pull = <0>; /* none */
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ int_pin = <ð1>, "interrupts:0",
-+ <ð1_pins>, "brcm,pins:0";
-+ speed = <ð1>, "spi-max-frequency:0";
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0557-lirc_rpi-Delete-vestigial-gpio_in_pull-parameter.patch b/target/linux/brcm2708/patches-4.4/0557-lirc_rpi-Delete-vestigial-gpio_in_pull-parameter.patch
deleted file mode 100644
index 58bab71..0000000
--- a/target/linux/brcm2708/patches-4.4/0557-lirc_rpi-Delete-vestigial-gpio_in_pull-parameter.patch
+++ /dev/null
@@ -1,38 +0,0 @@
-From d2517545ca23d2a147402f7c5f736d046e921b34 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 5 Dec 2016 09:58:16 +0000
-Subject: [PATCH] lirc_rpi: Delete vestigial gpio_in_pull parameter
-
-The RPi GPIO no longer support run-time "pull" settings - one should
-Device Tree and pinctrl instead - so remove the parameter to avoid
-confusion.
-
-See: https://github.com/raspberrypi/linux/issues/1711
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- drivers/staging/media/lirc/lirc_rpi.c | 6 ------
- 1 file changed, 6 deletions(-)
-
---- a/drivers/staging/media/lirc/lirc_rpi.c
-+++ b/drivers/staging/media/lirc/lirc_rpi.c
-@@ -64,8 +64,6 @@
-
- /* set the default GPIO input pin */
- static int gpio_in_pin = 18;
--/* set the default pull behaviour for input pin */
--static int gpio_in_pull = BCM2708_PULL_DOWN;
- /* set the default GPIO output pin */
- static int gpio_out_pin = 17;
- /* enable debugging messages */
-@@ -716,10 +714,6 @@ module_param(gpio_in_pin, int, S_IRUGO);
- MODULE_PARM_DESC(gpio_in_pin, "GPIO input pin number of the BCM processor."
- " (default 18");
-
--module_param(gpio_in_pull, int, S_IRUGO);
--MODULE_PARM_DESC(gpio_in_pull, "GPIO input pin pull configuration."
-- " (0 = off, 1 = up, 2 = down, default down)");
--
- module_param(sense, int, S_IRUGO);
- MODULE_PARM_DESC(sense, "Override autodetection of IR receiver circuit"
- " (0 = active high, 1 = active low )");
diff --git a/target/linux/brcm2708/patches-4.4/0558-BCM270X_DT-Add-i2c-sensor-overlay.patch b/target/linux/brcm2708/patches-4.4/0558-BCM270X_DT-Add-i2c-sensor-overlay.patch
deleted file mode 100644
index 4e653c3..0000000
--- a/target/linux/brcm2708/patches-4.4/0558-BCM270X_DT-Add-i2c-sensor-overlay.patch
+++ /dev/null
@@ -1,92 +0,0 @@
-From b2a2630ad69cc2f76fc027f1e730d6d82f84ea82 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 5 Dec 2016 17:10:44 +0000
-Subject: [PATCH] BCM270X_DT: Add i2c-sensor overlay
-
-The i2c-sensor overlay is a container for various pressure and
-temperature sensors, currently bmp085 and bmp280. The standalone
-bmp085_i2c-sensor overlay is now deprecated.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 12 ++++++--
- arch/arm/boot/dts/overlays/i2c-sensor-overlay.dts | 34 +++++++++++++++++++++++
- 3 files changed, 45 insertions(+), 2 deletions(-)
- create mode 100644 arch/arm/boot/dts/overlays/i2c-sensor-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -42,6 +42,7 @@ dtbo-$(RPI_DT_OVERLAYS) += i2c-gpio.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c-mux.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c-pwm-pca9685a.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c-rtc.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += i2c-sensor.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c0-bcm2708.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2c1-bcm2708.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += i2s-gpio28-31.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -283,8 +283,7 @@ Params: swap_lr Reverse
-
-
- Name: bmp085_i2c-sensor
--Info: Configures the BMP085/BMP180 digital barometric pressure and temperature
-- sensors from Bosch Sensortec
-+Info: This overlay is now deprecated - see i2c-sensor
- Load: dtoverlay=bmp085_i2c-sensor
- Params: <None>
-
-@@ -536,6 +535,15 @@ Params: abx80x Select o
- source
-
-
-+Name: i2c-sensor
-+Info: Adds support for a number of I2C barometric pressure and temperature
-+ sensors on i2c_arm
-+Load: dtoverlay=i2c-sensor,<param>=<val>
-+Params: bmp085 Select the Bosch sensortronic BMP085
-+
-+ bmp280 Select the Bosch sensortronic BMP280
-+
-+
- Name: i2c0-bcm2708
- Info: Enable the i2c_bcm2708 driver for the i2c0 bus. Not all pin combinations
- are usable on all platforms.
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/i2c-sensor-overlay.dts
-@@ -0,0 +1,34 @@
-+// Definitions for a few digital barometric pressure and temperature sensors
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&i2c_arm>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ bmp085: bmp085 at 77 {
-+ compatible = "bosch,bmp085";
-+ reg = <0x77>;
-+ default-oversampling = <3>;
-+ status = "disable";
-+ };
-+
-+ bmp280: bmp280 at 76 {
-+ compatible = "bosch,bmp280";
-+ reg = <0x76>;
-+ status = "disable";
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ bmp085 = <&bmp085>,"status";
-+ bmp280 = <&bmp280>,"status";
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0559-BCM270X_DT-overlays-overlay.dtb-overlays-.dtbo-1752.patch b/target/linux/brcm2708/patches-4.4/0559-BCM270X_DT-overlays-overlay.dtb-overlays-.dtbo-1752.patch
deleted file mode 100644
index 65f6606..0000000
--- a/target/linux/brcm2708/patches-4.4/0559-BCM270X_DT-overlays-overlay.dtb-overlays-.dtbo-1752.patch
+++ /dev/null
@@ -1,21 +0,0 @@
-From 862c54a1bf9ea4dd964747946b098e1287c016d4 Mon Sep 17 00:00:00 2001
-From: Georgii Staroselskii <gosha371 at gmail.com>
-Date: Wed, 7 Dec 2016 15:10:27 +0300
-Subject: [PATCH] BCM270X_DT: overlays/*-overlay.dtb -> overlays/*.dtbo (#1752)
-
-We now create overlays as .dtbo files.
----
- arch/arm/boot/dts/overlays/README | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -61,7 +61,7 @@ this becomes a line in config.txt:
-
- dtoverlay=lirc-rpi
-
--This causes the file /boot/overlays/lirc-rpi-overlay.dtb to be loaded. By
-+This causes the file /boot/overlays/lirc-rpi.dtbo to be loaded. By
- default it will use GPIOs 17 (out) and 18 (in), but this can be modified using
- DT parameters:
-
diff --git a/target/linux/brcm2708/patches-4.4/0560-Revert-HID-dragonrise-fix-HID-Descriptor-for-0x0006-.patch b/target/linux/brcm2708/patches-4.4/0560-Revert-HID-dragonrise-fix-HID-Descriptor-for-0x0006-.patch
deleted file mode 100644
index cb2c6e2..0000000
--- a/target/linux/brcm2708/patches-4.4/0560-Revert-HID-dragonrise-fix-HID-Descriptor-for-0x0006-.patch
+++ /dev/null
@@ -1,99 +0,0 @@
-From 067c44b3d4e3aabaf9e622621556556a607747a4 Mon Sep 17 00:00:00 2001
-From: Ioan-Adrian Ratiu <adi at adirat.com>
-Date: Tue, 27 Sep 2016 21:41:37 +0300
-Subject: [PATCH] Revert "HID: dragonrise: fix HID Descriptor for 0x0006 PID"
-
-[ Upstream commit 1bcaa05ebee115213e34f1806cc6a4f7a6175a88 ]
-This reverts commit 18339f59c3a6 ("HID: dragonrise: fix HID...") because it
-breaks certain dragonrise 0079:0006 gamepads. While it may fix a breakage
-caused by commit 79346d620e9d ("HID: input: force generic axis to be mapped
-to their user space axis"), it is probable that the manufacturer released
-different hardware with the same PID so this fix works for only a subset
-and breaks the other gamepads sharing the PID.
-
-What is needed is another more generic solution which fixes 79346d620e9d
-("HID: input: force generic axis ...") breakage for this controller: we
-need to add an exception for this driver to make it keep the old behaviour
-previous to the initial breakage (this is done in patch 2 of this series).
-
-Signed-off-by: Ioan-Adrian Ratiu <adi at adirat.com>
-Reviewed-by: Benjamin Tissoires <benjamin.tissoires at redhat.com>
-Signed-off-by: Jiri Kosina <jkosina at suse.cz>
----
- drivers/hid/hid-dr.c | 58 ----------------------------------------------------
- 1 file changed, 58 deletions(-)
-
---- a/drivers/hid/hid-dr.c
-+++ b/drivers/hid/hid-dr.c
-@@ -234,58 +234,6 @@ static __u8 pid0011_rdesc_fixed[] = {
- 0xC0 /* End Collection */
- };
-
--static __u8 pid0006_rdesc_fixed[] = {
-- 0x05, 0x01, /* Usage Page (Generic Desktop) */
-- 0x09, 0x04, /* Usage (Joystick) */
-- 0xA1, 0x01, /* Collection (Application) */
-- 0xA1, 0x02, /* Collection (Logical) */
-- 0x75, 0x08, /* Report Size (8) */
-- 0x95, 0x05, /* Report Count (5) */
-- 0x15, 0x00, /* Logical Minimum (0) */
-- 0x26, 0xFF, 0x00, /* Logical Maximum (255) */
-- 0x35, 0x00, /* Physical Minimum (0) */
-- 0x46, 0xFF, 0x00, /* Physical Maximum (255) */
-- 0x09, 0x30, /* Usage (X) */
-- 0x09, 0x33, /* Usage (Ry) */
-- 0x09, 0x32, /* Usage (Z) */
-- 0x09, 0x31, /* Usage (Y) */
-- 0x09, 0x34, /* Usage (Ry) */
-- 0x81, 0x02, /* Input (Variable) */
-- 0x75, 0x04, /* Report Size (4) */
-- 0x95, 0x01, /* Report Count (1) */
-- 0x25, 0x07, /* Logical Maximum (7) */
-- 0x46, 0x3B, 0x01, /* Physical Maximum (315) */
-- 0x65, 0x14, /* Unit (Centimeter) */
-- 0x09, 0x39, /* Usage (Hat switch) */
-- 0x81, 0x42, /* Input (Variable) */
-- 0x65, 0x00, /* Unit (None) */
-- 0x75, 0x01, /* Report Size (1) */
-- 0x95, 0x0C, /* Report Count (12) */
-- 0x25, 0x01, /* Logical Maximum (1) */
-- 0x45, 0x01, /* Physical Maximum (1) */
-- 0x05, 0x09, /* Usage Page (Button) */
-- 0x19, 0x01, /* Usage Minimum (0x01) */
-- 0x29, 0x0C, /* Usage Maximum (0x0C) */
-- 0x81, 0x02, /* Input (Variable) */
-- 0x06, 0x00, 0xFF, /* Usage Page (Vendor Defined) */
-- 0x75, 0x01, /* Report Size (1) */
-- 0x95, 0x08, /* Report Count (8) */
-- 0x25, 0x01, /* Logical Maximum (1) */
-- 0x45, 0x01, /* Physical Maximum (1) */
-- 0x09, 0x01, /* Usage (0x01) */
-- 0x81, 0x02, /* Input (Variable) */
-- 0xC0, /* End Collection */
-- 0xA1, 0x02, /* Collection (Logical) */
-- 0x75, 0x08, /* Report Size (8) */
-- 0x95, 0x07, /* Report Count (7) */
-- 0x46, 0xFF, 0x00, /* Physical Maximum (255) */
-- 0x26, 0xFF, 0x00, /* Logical Maximum (255) */
-- 0x09, 0x02, /* Usage (0x02) */
-- 0x91, 0x02, /* Output (Variable) */
-- 0xC0, /* End Collection */
-- 0xC0 /* End Collection */
--};
--
- static __u8 *dr_report_fixup(struct hid_device *hdev, __u8 *rdesc,
- unsigned int *rsize)
- {
-@@ -296,12 +244,6 @@ static __u8 *dr_report_fixup(struct hid_
- *rsize = sizeof(pid0011_rdesc_fixed);
- }
- break;
-- case 0x0006:
-- if (*rsize == sizeof(pid0006_rdesc_fixed)) {
-- rdesc = pid0006_rdesc_fixed;
-- *rsize = sizeof(pid0006_rdesc_fixed);
-- }
-- break;
- }
- return rdesc;
- }
diff --git a/target/linux/brcm2708/patches-4.4/0561-bcm2835-rng-Avoid-initialising-if-already-enabled.patch b/target/linux/brcm2708/patches-4.4/0561-bcm2835-rng-Avoid-initialising-if-already-enabled.patch
deleted file mode 100644
index b8cc66c..0000000
--- a/target/linux/brcm2708/patches-4.4/0561-bcm2835-rng-Avoid-initialising-if-already-enabled.patch
+++ /dev/null
@@ -1,26 +0,0 @@
-From ad841f8241807114d61572c1ca1636e7a43e6d93 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Tue, 6 Dec 2016 17:05:39 +0000
-Subject: [PATCH] bcm2835-rng: Avoid initialising if already enabled
-
-Avoids the 0x40000 cycles of warmup again if firmware has already used it
----
- drivers/char/hw_random/bcm2835-rng.c | 7 ++++---
- 1 file changed, 4 insertions(+), 3 deletions(-)
-
---- a/drivers/char/hw_random/bcm2835-rng.c
-+++ b/drivers/char/hw_random/bcm2835-rng.c
-@@ -62,9 +62,10 @@ static int bcm2835_rng_probe(struct plat
- bcm2835_rng_ops.priv = (unsigned long)rng_base;
-
- /* set warm-up count & enable */
-- __raw_writel(RNG_WARMUP_COUNT, rng_base + RNG_STATUS);
-- __raw_writel(RNG_RBGEN, rng_base + RNG_CTRL);
--
-+ if (!(__raw_readl(rng_base + RNG_CTRL) & RNG_RBGEN)) {
-+ __raw_writel(RNG_WARMUP_COUNT, rng_base + RNG_STATUS);
-+ __raw_writel(RNG_RBGEN, rng_base + RNG_CTRL);
-+ }
- /* register driver */
- err = hwrng_register(&bcm2835_rng_ops);
- if (err) {
diff --git a/target/linux/brcm2708/patches-4.4/0562-Pisound-dynamic-overlay-1760.patch b/target/linux/brcm2708/patches-4.4/0562-Pisound-dynamic-overlay-1760.patch
deleted file mode 100644
index 7acf5b2..0000000
--- a/target/linux/brcm2708/patches-4.4/0562-Pisound-dynamic-overlay-1760.patch
+++ /dev/null
@@ -1,144 +0,0 @@
-From 27b7e48055d8d31d8a03dbe7d8d4fccbc3ad7f31 Mon Sep 17 00:00:00 2001
-From: gtrainavicius <gtrainavicius at users.noreply.github.com>
-Date: Sat, 10 Dec 2016 16:05:25 +0200
-Subject: [PATCH] Pisound dynamic overlay (#1760)
-
-Restructuring pisound-overlay.dts, so it can be loaded and unloaded dynamically using dtoverlay.
-
-Print a logline when the kernel module is removed.
----
- arch/arm/boot/dts/overlays/pisound-overlay.dts | 94 ++++++++++++++------------
- sound/soc/bcm/pisound.c | 2 +
- 2 files changed, 52 insertions(+), 44 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/pisound-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/pisound-overlay.dts
-@@ -26,6 +26,54 @@
- compatible = "brcm,bcm2708";
-
- fragment at 0 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&spidev0>;
-+ __overlay__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target = <&spidev1>;
-+ __overlay__ {
-+ status = "okay";
-+ };
-+ };
-+
-+ fragment at 3 {
-+ target = <&spi0>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ pisound_spi: pisound_spi at 0{
-+ compatible = "blokaslabs,pisound-spi";
-+ reg = <0>;
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&spi0_pins>;
-+ spi-max-frequency = <1000000>;
-+ };
-+ };
-+ };
-+
-+ fragment at 4 {
-+ target-path = "/";
-+ __overlay__ {
-+ pcm5102a-codec {
-+ #sound-dai-cells = <0>;
-+ compatible = "ti,pcm5102a";
-+ status = "okay";
-+ };
-+ };
-+ };
-+
-+ fragment at 5 {
- target = <&sound>;
- __overlay__ {
- compatible = "blokaslabs,pisound";
-@@ -49,7 +97,7 @@
- };
- };
-
-- fragment at 1 {
-+ fragment at 6 {
- target = <&gpio>;
- __overlay__ {
- pinctrl-names = "default";
-@@ -63,52 +111,10 @@
- };
- };
-
-- fragment at 2 {
-+ fragment at 7 {
- target = <&i2s>;
- __overlay__ {
- status = "okay";
- };
- };
--
-- fragment at 3 {
-- target-path = "/";
-- __overlay__ {
-- pcm5102a-codec {
-- #sound-dai-cells = <0>;
-- compatible = "ti,pcm5102a";
-- status = "okay";
-- };
-- };
-- };
--
-- fragment at 4 {
-- target = <&spi0>;
-- __overlay__ {
-- status = "okay";
--
-- spidev at 0{
-- status = "disabled";
-- };
--
-- spidev at 1{
-- status = "okay";
-- };
-- };
-- };
--
-- fragment at 5 {
-- target = <&spi0>;
-- __overlay__ {
-- #address-cells = <1>;
-- #size-cells = <0>;
--
-- pisound_spi: pisound_spi at 0{
-- compatible = "blokaslabs,pisound-spi";
-- reg = <0>;
-- pinctrl-names = "default";
-- pinctrl-0 = <&spi0_pins>;
-- spi-max-frequency = <1000000>;
-- };
-- };
-- };
- };
---- a/sound/soc/bcm/pisound.c
-+++ b/sound/soc/bcm/pisound.c
-@@ -954,6 +954,8 @@ static int pisnd_probe(struct platform_d
-
- static int pisnd_remove(struct platform_device *pdev)
- {
-+ printi("Unloading.\n");
-+
- if (pisnd_kobj) {
- kobject_put(pisnd_kobj);
- pisnd_kobj = NULL;
diff --git a/target/linux/brcm2708/patches-4.4/0563-Add-support-for-Silicon-Labs-Si7013-20-21-humidity-t.patch b/target/linux/brcm2708/patches-4.4/0563-Add-support-for-Silicon-Labs-Si7013-20-21-humidity-t.patch
deleted file mode 100644
index 97938b3..0000000
--- a/target/linux/brcm2708/patches-4.4/0563-Add-support-for-Silicon-Labs-Si7013-20-21-humidity-t.patch
+++ /dev/null
@@ -1,90 +0,0 @@
-From f8bd38ac8b299bf55497f678e65babdd99d7e9f1 Mon Sep 17 00:00:00 2001
-From: Alex Tucker <alex at floop.org.uk>
-Date: Tue, 3 Jan 2017 21:30:41 +0000
-Subject: [PATCH] Add support for Silicon Labs Si7013/20/21
- humidity/temperature sensor. (#1765)
-
----
- arch/arm/boot/dts/overlays/README | 3 ++
- arch/arm/boot/dts/overlays/i2c-sensor-overlay.dts | 49 +++++++++++++----------
- 2 files changed, 31 insertions(+), 21 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -543,6 +543,9 @@ Params: bmp085 Select t
-
- bmp280 Select the Bosch sensortronic BMP280
-
-+ si7020 Select the Silicon Labs Si7013/20/21 humidity/
-+ temperature sensor
-+
-
- Name: i2c0-bcm2708
- Info: Enable the i2c_bcm2708 driver for the i2c0 bus. Not all pin combinations
---- a/arch/arm/boot/dts/overlays/i2c-sensor-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/i2c-sensor-overlay.dts
-@@ -1,34 +1,41 @@
--// Definitions for a few digital barometric pressure and temperature sensors
-+// Definitions for I2C based sensors using the Industrial IO interface.
- /dts-v1/;
- /plugin/;
-
- / {
-- compatible = "brcm,bcm2708";
-+ compatible = "brcm,bcm2708";
-
-- fragment at 0 {
-- target = <&i2c_arm>;
-- __overlay__ {
-- #address-cells = <1>;
-- #size-cells = <0>;
-- status = "okay";
--
-- bmp085: bmp085 at 77 {
-- compatible = "bosch,bmp085";
-- reg = <0x77>;
-- default-oversampling = <3>;
-- status = "disable";
-- };
--
-- bmp280: bmp280 at 76 {
-- compatible = "bosch,bmp280";
-- reg = <0x76>;
-- status = "disable";
-- };
-- };
-- };
-+ fragment at 0 {
-+ target = <&i2c_arm>;
-+ __overlay__ {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "okay";
-+
-+ bmp085: bmp085 at 77 {
-+ compatible = "bosch,bmp085";
-+ reg = <0x77>;
-+ default-oversampling = <3>;
-+ status = "disable";
-+ };
-+
-+ bmp280: bmp280 at 76 {
-+ compatible = "bosch,bmp280";
-+ reg = <0x76>;
-+ status = "disable";
-+ };
-+
-+ si7020: si7020 at 40 {
-+ compatible = "si7020";
-+ reg = <0x40>;
-+ status = "disable";
-+ };
-+ };
-+ };
-
- __overrides__ {
- bmp085 = <&bmp085>,"status";
- bmp280 = <&bmp280>,"status";
-+ si7020 = <&si7020>,"status";
- };
- };
diff --git a/target/linux/brcm2708/patches-4.4/0564-pisound-improvements-1778.patch b/target/linux/brcm2708/patches-4.4/0564-pisound-improvements-1778.patch
deleted file mode 100644
index 31dd3d6..0000000
--- a/target/linux/brcm2708/patches-4.4/0564-pisound-improvements-1778.patch
+++ /dev/null
@@ -1,294 +0,0 @@
-From afc3cd61521da7103489081731b1036d9d925197 Mon Sep 17 00:00:00 2001
-From: gtrainavicius <gtrainavicius at users.noreply.github.com>
-Date: Thu, 5 Jan 2017 17:08:45 +0200
-Subject: [PATCH] pisound improvements: (#1778)
-
-* Added a writable sysfs object to enable scripts / user space software
-to blink MIDI activity LEDs for variable duration.
-* Improved hw_param constraints setting.
-* Added compatibility with S16_LE sample format.
-* Exposed some simple placeholder volume controls, so the card appears
-in volumealsa widget.
-
-Signed-off-by: Giedrius Trainavicius <giedrius at blokas.io>
----
- sound/soc/bcm/pisound.c | 175 ++++++++++++++++++++++++++++++++++++++++++------
- 1 file changed, 154 insertions(+), 21 deletions(-)
-
---- a/sound/soc/bcm/pisound.c
-+++ b/sound/soc/bcm/pisound.c
-@@ -36,6 +36,7 @@
- #include <sound/jack.h>
- #include <sound/rawmidi.h>
- #include <sound/asequencer.h>
-+#include <sound/control.h>
-
- static int pisnd_spi_init(struct device *dev);
- static void pisnd_spi_uninit(void);
-@@ -214,6 +215,9 @@ static char g_serial_num[11];
- static char g_id[25];
- static char g_version[5];
-
-+static uint8_t g_ledFlashDuration;
-+static bool g_ledFlashDurationChanged;
-+
- DEFINE_KFIFO(spi_fifo_in, uint8_t, FIFO_SIZE);
- DEFINE_KFIFO(spi_fifo_out, uint8_t, FIFO_SIZE);
-
-@@ -396,8 +400,13 @@ static void pisnd_work_handler(struct wo
- val = 0;
- tx = 0;
-
-- if (kfifo_get(&spi_fifo_out, &val))
-+ if (g_ledFlashDurationChanged) {
-+ tx = 0xf000 | g_ledFlashDuration;
-+ g_ledFlashDuration = 0;
-+ g_ledFlashDurationChanged = false;
-+ } else if (kfifo_get(&spi_fifo_out, &val)) {
- tx = 0x0f00 | val;
-+ }
-
- rx = spi_transfer16(tx);
-
-@@ -410,6 +419,7 @@ static void pisnd_work_handler(struct wo
- } while (rx != 0
- || !kfifo_is_empty(&spi_fifo_out)
- || pisnd_spi_has_more()
-+ || g_ledFlashDurationChanged
- );
-
- if (!kfifo_is_empty(&spi_fifo_in) && g_recvCallback)
-@@ -569,7 +579,7 @@ static int pisnd_spi_init(struct device
- }
-
- /* Flash the LEDs. */
-- spi_transfer16(0xf000);
-+ spi_transfer16(0xf008);
-
- ret = pisnd_spi_gpio_irq_init(dev);
- if (ret < 0) {
-@@ -610,6 +620,14 @@ static void pisnd_spi_uninit(void)
- pisnd_spi_gpio_uninit();
- }
-
-+static void pisnd_spi_flash_leds(uint8_t duration)
-+{
-+ g_ledFlashDuration = duration;
-+ g_ledFlashDurationChanged = true;
-+ printd("schedule from spi_flash_leds\n");
-+ pisnd_schedule_process(TASK_PROCESS);
-+}
-+
- static void pisnd_spi_send(uint8_t val)
- {
- kfifo_put(&spi_fifo_out, val);
-@@ -658,6 +676,83 @@ static const struct of_device_id pisound
- {},
- };
-
-+enum {
-+ SWITCH = 0,
-+ VOLUME = 1,
-+};
-+
-+static int pisnd_ctl_info(struct snd_kcontrol *kcontrol,
-+ struct snd_ctl_elem_info *uinfo)
-+{
-+ if (kcontrol->private_value == SWITCH) {
-+ uinfo->type = SNDRV_CTL_ELEM_TYPE_BOOLEAN;
-+ uinfo->count = 1;
-+ uinfo->value.integer.min = 0;
-+ uinfo->value.integer.max = 1;
-+ return 0;
-+ } else if (kcontrol->private_value == VOLUME) {
-+ uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER;
-+ uinfo->count = 1;
-+ uinfo->value.integer.min = 0;
-+ uinfo->value.integer.max = 100;
-+ return 0;
-+ }
-+ return -EINVAL;
-+}
-+
-+static int pisnd_ctl_get(struct snd_kcontrol *kcontrol,
-+ struct snd_ctl_elem_value *ucontrol)
-+{
-+ if (kcontrol->private_value == SWITCH) {
-+ ucontrol->value.integer.value[0] = 1;
-+ return 0;
-+ } else if (kcontrol->private_value == VOLUME) {
-+ ucontrol->value.integer.value[0] = 100;
-+ return 0;
-+ }
-+
-+ return -EINVAL;
-+}
-+
-+static struct snd_kcontrol_new pisnd_ctl[] = {
-+ {
-+ .iface = SNDRV_CTL_ELEM_IFACE_MIXER,
-+ .name = "PCM Playback Switch",
-+ .index = 0,
-+ .private_value = SWITCH,
-+ .access = SNDRV_CTL_ELEM_ACCESS_READ,
-+ .info = pisnd_ctl_info,
-+ .get = pisnd_ctl_get,
-+ },
-+ {
-+ .iface = SNDRV_CTL_ELEM_IFACE_MIXER,
-+ .name = "PCM Playback Volume",
-+ .index = 0,
-+ .private_value = VOLUME,
-+ .access = SNDRV_CTL_ELEM_ACCESS_READ,
-+ .info = pisnd_ctl_info,
-+ .get = pisnd_ctl_get,
-+ },
-+};
-+
-+static int pisnd_ctl_init(struct snd_card *card)
-+{
-+ int err, i;
-+
-+ for (i = 0; i < ARRAY_SIZE(pisnd_ctl); ++i) {
-+ err = snd_ctl_add(card, snd_ctl_new1(&pisnd_ctl[i], NULL));
-+ if (err < 0)
-+ return err;
-+ }
-+
-+ return 0;
-+}
-+
-+static int pisnd_ctl_uninit(void)
-+{
-+ return 0;
-+}
-+
- static struct gpio_desc *osr0, *osr1, *osr2;
- static struct gpio_desc *reset;
- static struct gpio_desc *button;
-@@ -667,6 +762,14 @@ static int pisnd_hw_params(
- struct snd_pcm_hw_params *params
- )
- {
-+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
-+ struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
-+
-+ /* pisound runs on fixed 32 clock counts per channel,
-+ * as generated by the master ADC.
-+ */
-+ snd_soc_dai_set_bclk_ratio(cpu_dai, 32*2);
-+
- printd("rate = %d\n", params_rate(params));
- printd("ch = %d\n", params_channels(params));
- printd("bits = %u\n",
-@@ -711,16 +814,6 @@ static struct snd_pcm_hw_constraint_list
- .mask = 0,
- };
-
--static unsigned int sample_bits[] = {
-- 24, 32
--};
--
--static struct snd_pcm_hw_constraint_list constraints_sample_bits = {
-- .count = ARRAY_SIZE(sample_bits),
-- .list = sample_bits,
-- .mask = 0,
--};
--
- static int pisnd_startup(struct snd_pcm_substream *substream)
- {
- int err = snd_pcm_hw_constraint_list(
-@@ -733,11 +826,21 @@ static int pisnd_startup(struct snd_pcm_
- if (err < 0)
- return err;
-
-- err = snd_pcm_hw_constraint_list(
-+ err = snd_pcm_hw_constraint_single(
- substream->runtime,
-- 0,
-- SNDRV_PCM_HW_PARAM_SAMPLE_BITS,
-- &constraints_sample_bits
-+ SNDRV_PCM_HW_PARAM_CHANNELS,
-+ 2
-+ );
-+
-+ if (err < 0)
-+ return err;
-+
-+ err = snd_pcm_hw_constraint_mask64(
-+ substream->runtime,
-+ SNDRV_PCM_HW_PARAM_FORMAT,
-+ SNDRV_PCM_FMTBIT_S16_LE |
-+ SNDRV_PCM_FMTBIT_S24_LE |
-+ SNDRV_PCM_FMTBIT_S32_LE
- );
-
- if (err < 0)
-@@ -771,14 +874,23 @@ static int pisnd_card_probe(struct snd_s
- {
- int err = pisnd_midi_init(card->snd_card);
-
-- if (err < 0)
-+ if (err < 0) {
- printe("pisnd_midi_init failed: %d\n", err);
-+ return err;
-+ }
-
-- return err;
-+ err = pisnd_ctl_init(card->snd_card);
-+ if (err < 0) {
-+ printe("pisnd_ctl_init failed: %d\n", err);
-+ return err;
-+ }
-+
-+ return 0;
- }
-
- static int pisnd_card_remove(struct snd_soc_card *card)
- {
-+ pisnd_ctl_uninit();
- pisnd_midi_uninit();
- return 0;
- }
-@@ -870,17 +982,38 @@ static ssize_t pisnd_version_show(
- return sprintf(buf, "%s\n", pisnd_spi_get_version());
- }
-
-+static ssize_t pisnd_led_store(
-+ struct kobject *kobj,
-+ struct kobj_attribute *attr,
-+ const char *buf,
-+ size_t length
-+ )
-+{
-+ uint32_t timeout;
-+ int err;
-+
-+ err = kstrtou32(buf, 10, &timeout);
-+
-+ if (err == 0 && timeout <= 255)
-+ pisnd_spi_flash_leds(timeout);
-+
-+ return length;
-+}
-+
- static struct kobj_attribute pisnd_serial_attribute =
-- __ATTR(serial, 0644, pisnd_serial_show, NULL);
-+ __ATTR(serial, 0444, pisnd_serial_show, NULL);
- static struct kobj_attribute pisnd_id_attribute =
-- __ATTR(id, 0644, pisnd_id_show, NULL);
-+ __ATTR(id, 0444, pisnd_id_show, NULL);
- static struct kobj_attribute pisnd_version_attribute =
-- __ATTR(version, 0644, pisnd_version_show, NULL);
-+ __ATTR(version, 0444, pisnd_version_show, NULL);
-+static struct kobj_attribute pisnd_led_attribute =
-+ __ATTR(led, 0644, NULL, pisnd_led_store);
-
- static struct attribute *attrs[] = {
- &pisnd_serial_attribute.attr,
- &pisnd_id_attribute.attr,
- &pisnd_version_attribute.attr,
-+ &pisnd_led_attribute.attr,
- NULL
- };
-
diff --git a/target/linux/brcm2708/patches-4.4/0565-Add-driver_name-properties-to-JustBoom-drivers-1787.patch b/target/linux/brcm2708/patches-4.4/0565-Add-driver_name-properties-to-JustBoom-drivers-1787.patch
deleted file mode 100644
index e5c324d..0000000
--- a/target/linux/brcm2708/patches-4.4/0565-Add-driver_name-properties-to-JustBoom-drivers-1787.patch
+++ /dev/null
@@ -1,32 +0,0 @@
-From 23bd0578bdaf97a05a29fff25850d3fde26cb686 Mon Sep 17 00:00:00 2001
-From: Aaron Shaw <shawaj at gmail.com>
-Date: Tue, 10 Jan 2017 16:22:53 +0000
-Subject: [PATCH] Add driver_name properties to JustBoom drivers (#1787)
-
-Add driver name properties for use with 5.1 passthrough audio in LibreElec
-and other Kodi based OSs
----
- sound/soc/bcm/justboom-dac.c | 1 +
- sound/soc/bcm/justboom-digi.c | 1 +
- 2 files changed, 2 insertions(+)
-
---- a/sound/soc/bcm/justboom-dac.c
-+++ b/sound/soc/bcm/justboom-dac.c
-@@ -98,6 +98,7 @@ static struct snd_soc_dai_link snd_rpi_j
- /* audio machine driver */
- static struct snd_soc_card snd_rpi_justboom_dac = {
- .name = "snd_rpi_justboom_dac",
-+ .driver_name = "JustBoomDac",
- .owner = THIS_MODULE,
- .dai_link = snd_rpi_justboom_dac_dai,
- .num_links = ARRAY_SIZE(snd_rpi_justboom_dac_dai),
---- a/sound/soc/bcm/justboom-digi.c
-+++ b/sound/soc/bcm/justboom-digi.c
-@@ -154,6 +154,7 @@ static struct snd_soc_dai_link snd_rpi_j
- /* audio machine driver */
- static struct snd_soc_card snd_rpi_justboom_digi = {
- .name = "snd_rpi_justboom_digi",
-+ .driver_name = "JustBoomDigi",
- .owner = THIS_MODULE,
- .dai_link = snd_rpi_justboom_digi_dai,
- .num_links = ARRAY_SIZE(snd_rpi_justboom_digi_dai),
diff --git a/target/linux/brcm2708/patches-4.4/0566-bcm2835-i2s-Changes-for-allowing-asymmetric-sample-f.patch b/target/linux/brcm2708/patches-4.4/0566-bcm2835-i2s-Changes-for-allowing-asymmetric-sample-f.patch
deleted file mode 100644
index 88c001c..0000000
--- a/target/linux/brcm2708/patches-4.4/0566-bcm2835-i2s-Changes-for-allowing-asymmetric-sample-f.patch
+++ /dev/null
@@ -1,96 +0,0 @@
-From b7c0618121a4cf0efdcecb4e36ad0be0430be0b3 Mon Sep 17 00:00:00 2001
-From: gtrainavicius <gtrainavicius at users.noreply.github.com>
-Date: Tue, 10 Jan 2017 21:59:39 +0200
-Subject: [PATCH] bcm2835-i2s: Changes for allowing asymmetric sample formats.
- (#1783)
-
-This is achieved by making changes only to the requested
-stream direction format, keeping the other stream direction
-configuration intact.
-
-Signed-off-by: Giedrius Trainavicius <giedrius at blokas.io>
----
- sound/soc/bcm/bcm2835-i2s.c | 54 +++++++++++++++++++++++++++++++--------------
- 1 file changed, 38 insertions(+), 16 deletions(-)
-
---- a/sound/soc/bcm/bcm2835-i2s.c
-+++ b/sound/soc/bcm/bcm2835-i2s.c
-@@ -310,6 +310,7 @@ static int bcm2835_i2s_hw_params(struct
- unsigned int sampling_rate = params_rate(params);
- unsigned int data_length, data_delay, bclk_ratio;
- unsigned int ch1pos, ch2pos, mode, format;
-+ unsigned int previous_ftxp, previous_frxp;
- unsigned int mash = BCM2835_CLK_MASH_1;
- unsigned int divi, divf, target_frequency;
- int clk_src = -1;
-@@ -320,6 +321,7 @@ static int bcm2835_i2s_hw_params(struct
- bool frame_master = (master == SND_SOC_DAIFMT_CBS_CFS
- || master == SND_SOC_DAIFMT_CBM_CFS);
- uint32_t csreg;
-+ bool packed;
-
- /*
- * If a stream is already enabled,
-@@ -465,26 +467,46 @@ static int bcm2835_i2s_hw_params(struct
- return -EINVAL;
- }
-
-- /*
-- * Set format for both streams.
-- * We cannot set another frame length
-- * (and therefore word length) anyway,
-- * so the format will be the same.
-- */
-- regmap_write(dev->i2s_regmap, BCM2835_I2S_RXC_A_REG, format);
-- regmap_write(dev->i2s_regmap, BCM2835_I2S_TXC_A_REG, format);
-+ /* Set the format for the matching stream direction. */
-+ switch (substream->stream) {
-+ case SNDRV_PCM_STREAM_PLAYBACK:
-+ regmap_write(dev->i2s_regmap, BCM2835_I2S_TXC_A_REG, format);
-+ break;
-+ case SNDRV_PCM_STREAM_CAPTURE:
-+ regmap_write(dev->i2s_regmap, BCM2835_I2S_RXC_A_REG, format);
-+ break;
-+ default:
-+ return -EINVAL;
-+ }
-
- /* Setup the I2S mode */
-+ /* Keep existing FTXP and FRXP values. */
-+ regmap_read(dev->i2s_regmap, BCM2835_I2S_MODE_A_REG, &mode);
-+
-+ previous_ftxp = mode & BCM2835_I2S_FTXP;
-+ previous_frxp = mode & BCM2835_I2S_FRXP;
-+
- mode = 0;
-
-- if (data_length <= 16) {
-- /*
-- * Use frame packed mode (2 channels per 32 bit word)
-- * We cannot set another frame length in the second stream
-- * (and therefore word length) anyway,
-- * so the format will be the same.
-- */
-- mode |= BCM2835_I2S_FTXP | BCM2835_I2S_FRXP;
-+ /*
-+ * Retain the frame packed mode (2 channels per 32 bit word)
-+ * of the other direction stream intact. The formats of each
-+ * direction can be different as long as the frame length is
-+ * shared for both.
-+ */
-+ packed = data_length <= 16;
-+
-+ switch (substream->stream) {
-+ case SNDRV_PCM_STREAM_PLAYBACK:
-+ mode |= previous_frxp;
-+ mode |= packed ? BCM2835_I2S_FTXP : 0;
-+ break;
-+ case SNDRV_PCM_STREAM_CAPTURE:
-+ mode |= previous_ftxp;
-+ mode |= packed ? BCM2835_I2S_FRXP : 0;
-+ break;
-+ default:
-+ return -EINVAL;
- }
-
- mode |= BCM2835_I2S_FLEN(bclk_ratio - 1);
diff --git a/target/linux/brcm2708/patches-4.4/0567-BCM270X_DT-Add-pi3-disable-wifi-overlay.patch b/target/linux/brcm2708/patches-4.4/0567-BCM270X_DT-Add-pi3-disable-wifi-overlay.patch
deleted file mode 100644
index fc36490..0000000
--- a/target/linux/brcm2708/patches-4.4/0567-BCM270X_DT-Add-pi3-disable-wifi-overlay.patch
+++ /dev/null
@@ -1,56 +0,0 @@
-From 04b3aace4865f06b982c33d03098dceb02be67a4 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Wed, 11 Jan 2017 13:01:21 +0000
-Subject: [PATCH] BCM270X_DT: Add pi3-disable-wifi overlay
-
-pi3-disable-wifi is a minimal overlay to disable the onboard WiFi.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 6 ++++++
- arch/arm/boot/dts/overlays/pi3-disable-wifi-overlay.dts | 13 +++++++++++++
- 3 files changed, 20 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/pi3-disable-wifi-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -61,6 +61,7 @@ dtbo-$(RPI_DT_OVERLAYS) += mmc.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += mz61581.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += pi3-act-led.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += pi3-disable-bt.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += pi3-disable-wifi.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += pi3-miniuart-bt.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += piscreen.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += piscreen2r.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -793,6 +793,12 @@ Load: dtoverlay=pi3-disable-bt
- Params: <None>
-
-
-+Name: pi3-disable-wifi
-+Info: Disable Pi3 onboard WiFi
-+Load: dtoverlay=pi3-disable-wifi
-+Params: <None>
-+
-+
- Name: pi3-miniuart-bt
- Info: Switch Pi3 Bluetooth function to use the mini-UART (ttyS0) and restore
- UART0/ttyAMA0 over GPIOs 14 & 15. Note that this may reduce the maximum
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/pi3-disable-wifi-overlay.dts
-@@ -0,0 +1,13 @@
-+/dts-v1/;
-+/plugin/;
-+
-+/{
-+ compatible = "brcm,bcm2708";
-+
-+ fragment at 0 {
-+ target = <&mmc>;
-+ __overlay__ {
-+ status = "disabled";
-+ };
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0568-configfs-Remove-ppos-increment-in-configfs_write_bin.patch b/target/linux/brcm2708/patches-4.4/0568-configfs-Remove-ppos-increment-in-configfs_write_bin.patch
deleted file mode 100644
index 842cb8b..0000000
--- a/target/linux/brcm2708/patches-4.4/0568-configfs-Remove-ppos-increment-in-configfs_write_bin.patch
+++ /dev/null
@@ -1,49 +0,0 @@
-From ec490344ba1906dfdbbb6baaa0349fe2ad3d463d Mon Sep 17 00:00:00 2001
-From: Marek Vasut <marex at denx.de>
-Date: Wed, 18 May 2016 16:16:51 +0200
-Subject: [PATCH] configfs: Remove ppos increment in configfs_write_bin_file
-
-[ Back-port of f8608985f851c917b3884b692d8e326b0210d34e ]
-
-The simple_write_to_buffer() already increments the @ppos on success,
-see fs/libfs.c simple_write_to_buffer() comment:
-
-"
-On success, the number of bytes written is returned and the offset @ppos
-advanced by this number, or negative value is returned on error.
-"
-
-If the configfs_write_bin_file() is invoked with @count smaller than the
-total length of the written binary file, it will be invoked multiple times.
-Since configfs_write_bin_file() increments @ppos on success, after calling
-simple_write_to_buffer(), the @ppos is incremented twice.
-
-Subsequent invocation of configfs_write_bin_file() will result in the next
-piece of data being written to the offset twice as long as the length of
-the previous write, thus creating buffer with "holes" in it.
-
-The simple testcase using DTO follows:
- $ mkdir /sys/kernel/config/device-tree/overlays/1
- $ dd bs=1 if=foo.dtbo of=/sys/kernel/config/device-tree/overlays/1/dtbo
-Without this patch, the testcase will result in twice as big buffer in the
-kernel, which is then passed to the cfs_overlay_item_dtbo_write() .
-
-Signed-off-by: Marek Vasut <marex at denx.de>
-Cc: Geert Uytterhoeven <geert+renesas at glider.be>
-Cc: Christoph Hellwig <hch at lst.de>
-Cc: Pantelis Antoniou <pantelis.antoniou at konsulko.com>
----
- fs/configfs/file.c | 2 --
- 1 file changed, 2 deletions(-)
-
---- a/fs/configfs/file.c
-+++ b/fs/configfs/file.c
-@@ -357,8 +357,6 @@ configfs_write_bin_file(struct file *fil
-
- len = simple_write_to_buffer(buffer->bin_buffer,
- buffer->bin_buffer_size, ppos, buf, count);
-- if (len > 0)
-- *ppos += len;
- out:
- mutex_unlock(&buffer->mutex);
- return len;
diff --git a/target/linux/brcm2708/patches-4.4/0569-config-Add-CONFIG_DM_CACHE.patch b/target/linux/brcm2708/patches-4.4/0569-config-Add-CONFIG_DM_CACHE.patch
deleted file mode 100644
index 9ac4c03..0000000
--- a/target/linux/brcm2708/patches-4.4/0569-config-Add-CONFIG_DM_CACHE.patch
+++ /dev/null
@@ -1,31 +0,0 @@
-From a924593ec575d894135fbb8c6500e6a165551760 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Sun, 15 Jan 2017 21:56:59 +0000
-Subject: [PATCH] config: Add CONFIG_DM_CACHE See:
- https://github.com/raspberrypi/linux/issues/1793
-
----
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 2 files changed, 2 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -438,6 +438,7 @@ CONFIG_BLK_DEV_DM=m
- CONFIG_DM_CRYPT=m
- CONFIG_DM_SNAPSHOT=m
- CONFIG_DM_THIN_PROVISIONING=m
-+CONFIG_DM_CACHE=m
- CONFIG_DM_MIRROR=m
- CONFIG_DM_LOG_USERSPACE=m
- CONFIG_DM_RAID=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -431,6 +431,7 @@ CONFIG_BLK_DEV_DM=m
- CONFIG_DM_CRYPT=m
- CONFIG_DM_SNAPSHOT=m
- CONFIG_DM_THIN_PROVISIONING=m
-+CONFIG_DM_CACHE=m
- CONFIG_DM_MIRROR=m
- CONFIG_DM_LOG_USERSPACE=m
- CONFIG_DM_RAID=m
diff --git a/target/linux/brcm2708/patches-4.4/0570-BCM270X_DT-Add-spi0-cs-overlay.patch b/target/linux/brcm2708/patches-4.4/0570-BCM270X_DT-Add-spi0-cs-overlay.patch
deleted file mode 100644
index 7dd62a7..0000000
--- a/target/linux/brcm2708/patches-4.4/0570-BCM270X_DT-Add-spi0-cs-overlay.patch
+++ /dev/null
@@ -1,81 +0,0 @@
-From 03e5edc82cd5df9f0fc6704d59a6f9aee3ef3552 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 16 Jan 2017 14:53:12 +0000
-Subject: [PATCH] BCM270X_DT: Add spi0-cs overlay
-
-The spi0-cs overlay allows the software chip selectts to be modified
-using the cs0_pin and cs1_pin parameters.
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 9 +++++++-
- arch/arm/boot/dts/overlays/spi0-cs-overlay.dts | 29 ++++++++++++++++++++++++++
- 3 files changed, 38 insertions(+), 1 deletion(-)
- create mode 100644 arch/arm/boot/dts/overlays/spi0-cs-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -93,6 +93,7 @@ dtbo-$(RPI_DT_OVERLAYS) += smi-dev.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += smi-nand.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += spi-gpio35-39.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += spi-rtc.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += spi0-cs.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += spi0-hw-cs.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += spi1-1cs.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += spi1-2cs.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -1131,7 +1131,7 @@ Params: <None>
-
-
- Name: spi-gpio35-39
--Info: move SPI function block to GPIO 35 to 39
-+Info: Move SPI function block to GPIO 35 to 39
- Load: dtoverlay=spi-gpio35-39
- Params: <None>
-
-@@ -1142,6 +1142,13 @@ Load: dtoverlay=spi-rtc,<param>=<val>
- Params: pcf2123 Select the PCF2123 device
-
-
-+Name: spi0-cs
-+Info: Allows the (software) CS pins for SPI0 to be changed
-+Load: dtoverlay=spi0-cs,<param>=<val>
-+Params: cs0_pin GPIO pin for CS0 (default 8)
-+ cs1_pin GPIO pin for CS1 (default 7)
-+
-+
- Name: spi0-hw-cs
- Info: Re-enables hardware CS/CE (chip selects) for SPI0
- Load: dtoverlay=spi0-hw-cs
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/spi0-cs-overlay.dts
-@@ -0,0 +1,29 @@
-+/dts-v1/;
-+/plugin/;
-+
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&spi0_cs_pins>;
-+ frag0: __overlay__ {
-+ brcm,pins = <8 7>;
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&spi0>;
-+ frag1: __overlay__ {
-+ cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
-+ status = "okay";
-+ };
-+ };
-+
-+ __overrides__ {
-+ cs0_pin = <&frag0>,"brcm,pins:0",
-+ <&frag1>,"cs-gpios:4";
-+ cs1_pin = <&frag0>,"brcm,pins:4",
-+ <&frag1>,"cs-gpios:16";
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0571-Revert-bcm2835-i2s-Changes-for-allowing-asymmetric-s.patch b/target/linux/brcm2708/patches-4.4/0571-Revert-bcm2835-i2s-Changes-for-allowing-asymmetric-s.patch
deleted file mode 100644
index c6b5106..0000000
--- a/target/linux/brcm2708/patches-4.4/0571-Revert-bcm2835-i2s-Changes-for-allowing-asymmetric-s.patch
+++ /dev/null
@@ -1,96 +0,0 @@
-From 7a4ba191d95833159eaea4329a806297d31a50da Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 16 Jan 2017 20:58:18 +0000
-Subject: [PATCH] Revert "bcm2835-i2s: Changes for allowing asymmetric sample
- formats. (#1783)"
-
-This reverts commit 4897c5c2f7adb4f77d638121e9959174dff87b9c.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
-
-See: https://github.com/raspberrypi/linux/issues/1799
----
- sound/soc/bcm/bcm2835-i2s.c | 54 ++++++++++++++-------------------------------
- 1 file changed, 16 insertions(+), 38 deletions(-)
-
---- a/sound/soc/bcm/bcm2835-i2s.c
-+++ b/sound/soc/bcm/bcm2835-i2s.c
-@@ -310,7 +310,6 @@ static int bcm2835_i2s_hw_params(struct
- unsigned int sampling_rate = params_rate(params);
- unsigned int data_length, data_delay, bclk_ratio;
- unsigned int ch1pos, ch2pos, mode, format;
-- unsigned int previous_ftxp, previous_frxp;
- unsigned int mash = BCM2835_CLK_MASH_1;
- unsigned int divi, divf, target_frequency;
- int clk_src = -1;
-@@ -321,7 +320,6 @@ static int bcm2835_i2s_hw_params(struct
- bool frame_master = (master == SND_SOC_DAIFMT_CBS_CFS
- || master == SND_SOC_DAIFMT_CBM_CFS);
- uint32_t csreg;
-- bool packed;
-
- /*
- * If a stream is already enabled,
-@@ -467,46 +465,26 @@ static int bcm2835_i2s_hw_params(struct
- return -EINVAL;
- }
-
-- /* Set the format for the matching stream direction. */
-- switch (substream->stream) {
-- case SNDRV_PCM_STREAM_PLAYBACK:
-- regmap_write(dev->i2s_regmap, BCM2835_I2S_TXC_A_REG, format);
-- break;
-- case SNDRV_PCM_STREAM_CAPTURE:
-- regmap_write(dev->i2s_regmap, BCM2835_I2S_RXC_A_REG, format);
-- break;
-- default:
-- return -EINVAL;
-- }
-+ /*
-+ * Set format for both streams.
-+ * We cannot set another frame length
-+ * (and therefore word length) anyway,
-+ * so the format will be the same.
-+ */
-+ regmap_write(dev->i2s_regmap, BCM2835_I2S_RXC_A_REG, format);
-+ regmap_write(dev->i2s_regmap, BCM2835_I2S_TXC_A_REG, format);
-
- /* Setup the I2S mode */
-- /* Keep existing FTXP and FRXP values. */
-- regmap_read(dev->i2s_regmap, BCM2835_I2S_MODE_A_REG, &mode);
--
-- previous_ftxp = mode & BCM2835_I2S_FTXP;
-- previous_frxp = mode & BCM2835_I2S_FRXP;
--
- mode = 0;
-
-- /*
-- * Retain the frame packed mode (2 channels per 32 bit word)
-- * of the other direction stream intact. The formats of each
-- * direction can be different as long as the frame length is
-- * shared for both.
-- */
-- packed = data_length <= 16;
--
-- switch (substream->stream) {
-- case SNDRV_PCM_STREAM_PLAYBACK:
-- mode |= previous_frxp;
-- mode |= packed ? BCM2835_I2S_FTXP : 0;
-- break;
-- case SNDRV_PCM_STREAM_CAPTURE:
-- mode |= previous_ftxp;
-- mode |= packed ? BCM2835_I2S_FRXP : 0;
-- break;
-- default:
-- return -EINVAL;
-+ if (data_length <= 16) {
-+ /*
-+ * Use frame packed mode (2 channels per 32 bit word)
-+ * We cannot set another frame length in the second stream
-+ * (and therefore word length) anyway,
-+ * so the format will be the same.
-+ */
-+ mode |= BCM2835_I2S_FTXP | BCM2835_I2S_FRXP;
- }
-
- mode |= BCM2835_I2S_FLEN(bclk_ratio - 1);
diff --git a/target/linux/brcm2708/patches-4.4/0572-BCM270X_DT-Enable-UART0-on-CM3.patch b/target/linux/brcm2708/patches-4.4/0572-BCM270X_DT-Enable-UART0-on-CM3.patch
deleted file mode 100644
index 8e9881a..0000000
--- a/target/linux/brcm2708/patches-4.4/0572-BCM270X_DT-Enable-UART0-on-CM3.patch
+++ /dev/null
@@ -1,23 +0,0 @@
-From 3ad406903deb46fbdbf4283f0d1d79911e96250a Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Tue, 17 Jan 2017 11:34:58 +0000
-Subject: [PATCH] BCM270X_DT: Enable UART0 on CM3
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/bcm2710-rpi-cm3.dts | 4 ++++
- 1 file changed, 4 insertions(+)
-
---- a/arch/arm/boot/dts/bcm2710-rpi-cm3.dts
-+++ b/arch/arm/boot/dts/bcm2710-rpi-cm3.dts
-@@ -7,6 +7,10 @@
- model = "Raspberry Pi Compute Module 3";
- };
-
-+&uart0 {
-+ status = "okay";
-+};
-+
- &gpio {
- sdhost_pins: sdhost_pins {
- brcm,pins = <48 49 50 51 52 53>;
diff --git a/target/linux/brcm2708/patches-4.4/0573-config-Add-CONFIG_MD_M25P80-and-CONFIG_MD_SPI_NOR.patch b/target/linux/brcm2708/patches-4.4/0573-config-Add-CONFIG_MD_M25P80-and-CONFIG_MD_SPI_NOR.patch
deleted file mode 100644
index 8cd1384..0000000
--- a/target/linux/brcm2708/patches-4.4/0573-config-Add-CONFIG_MD_M25P80-and-CONFIG_MD_SPI_NOR.patch
+++ /dev/null
@@ -1,37 +0,0 @@
-From df7b80d750d34fef14b646c4194eb00f482e22bb Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Tue, 17 Jan 2017 14:39:39 +0000
-Subject: [PATCH] config: Add CONFIG_MD_M25P80 and CONFIG_MD_SPI_NOR
-
-See: https://github.com/raspberrypi/linux/issues/1781
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/configs/bcm2709_defconfig | 2 ++
- arch/arm/configs/bcmrpi_defconfig | 2 ++
- 2 files changed, 4 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -407,7 +407,9 @@ CONFIG_DMA_CMA=y
- CONFIG_CMA_SIZE_MBYTES=5
- CONFIG_MTD=m
- CONFIG_MTD_BLOCK=m
-+CONFIG_MTD_M25P80=m
- CONFIG_MTD_NAND=m
-+CONFIG_MTD_SPI_NOR=m
- CONFIG_MTD_UBI=m
- CONFIG_OF_CONFIGFS=y
- CONFIG_ZRAM=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -400,7 +400,9 @@ CONFIG_DMA_CMA=y
- CONFIG_CMA_SIZE_MBYTES=5
- CONFIG_MTD=m
- CONFIG_MTD_BLOCK=m
-+CONFIG_MTD_M25P80=m
- CONFIG_MTD_NAND=m
-+CONFIG_MTD_SPI_NOR=m
- CONFIG_MTD_UBI=m
- CONFIG_OF_CONFIGFS=y
- CONFIG_ZRAM=m
diff --git a/target/linux/brcm2708/patches-4.4/0574-config-More-USB-config-options-for-bcm2709_defconfig.patch b/target/linux/brcm2708/patches-4.4/0574-config-More-USB-config-options-for-bcm2709_defconfig.patch
deleted file mode 100644
index e59978a..0000000
--- a/target/linux/brcm2708/patches-4.4/0574-config-More-USB-config-options-for-bcm2709_defconfig.patch
+++ /dev/null
@@ -1,48 +0,0 @@
-From c2276d9d2cdd7c6ed65e7b251257e3f73b659641 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <pelwell at users.noreply.github.com>
-Date: Thu, 19 Jan 2017 16:44:43 +0000
-Subject: [PATCH] config: More USB config options for bcm2709_defconfig (#1805)
-
-Bring bcm2709_defconfig up to the level of bcmrpi_defconfig with
-respect to USB support. This is prompted by the introduction of CM3,
-which makes gadget mode on 2709/2710 a useful option.
-
-Note that the DWC2 driver is not loaded by default and must be enabled
-using a DT overlay or custom .dtb.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/configs/bcm2709_defconfig | 15 +++++++++++++++
- 1 file changed, 15 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -969,6 +969,7 @@ CONFIG_USB_MICROTEK=m
- CONFIG_USBIP_CORE=m
- CONFIG_USBIP_VHCI_HCD=m
- CONFIG_USBIP_HOST=m
-+CONFIG_USB_DWC2=m
- CONFIG_USB_SERIAL=m
- CONFIG_USB_SERIAL_GENERIC=y
- CONFIG_USB_SERIAL_AIRCABLE=m
-@@ -1042,6 +1043,20 @@ CONFIG_USB_SPEEDTOUCH=m
- CONFIG_USB_CXACRU=m
- CONFIG_USB_UEAGLEATM=m
- CONFIG_USB_XUSBATM=m
-+CONFIG_USB_GADGET=m
-+CONFIG_USB_ZERO=m
-+CONFIG_USB_AUDIO=m
-+CONFIG_USB_ETH=m
-+CONFIG_USB_GADGETFS=m
-+CONFIG_USB_MASS_STORAGE=m
-+CONFIG_USB_G_SERIAL=m
-+CONFIG_USB_MIDI_GADGET=m
-+CONFIG_USB_G_PRINTER=m
-+CONFIG_USB_CDC_COMPOSITE=m
-+CONFIG_USB_G_ACM_MS=m
-+CONFIG_USB_G_MULTI=m
-+CONFIG_USB_G_HID=m
-+CONFIG_USB_G_WEBCAM=m
- CONFIG_MMC=y
- CONFIG_MMC_BLOCK_MINORS=32
- CONFIG_MMC_BCM2835=y
diff --git a/target/linux/brcm2708/patches-4.4/0575-BCM270X_DT-Add-reference-to-audio_pins-to-CM-dtb.patch b/target/linux/brcm2708/patches-4.4/0575-BCM270X_DT-Add-reference-to-audio_pins-to-CM-dtb.patch
deleted file mode 100644
index 203870f..0000000
--- a/target/linux/brcm2708/patches-4.4/0575-BCM270X_DT-Add-reference-to-audio_pins-to-CM-dtb.patch
+++ /dev/null
@@ -1,28 +0,0 @@
-From e11feff65e7ee74fce499a3514cb3bc22dc0c88f Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil at raspberrypi.org>
-Date: Mon, 23 Jan 2017 17:36:50 +0000
-Subject: [PATCH] BCM270X_DT: Add reference to audio_pins to CM dtb
-
-The CM1 dtb contains an empty audio_pins node, but no reference to it.
-Adding the usual pinctrl reference from the audio node enables the
-audremap overlay (and others) to easily turn on audio.
-
-Signed-off-by: Phil Elwell <phil at raspberrypi.org>
----
- arch/arm/boot/dts/bcm2708-rpi-cm.dtsi | 5 +++++
- 1 file changed, 5 insertions(+)
-
---- a/arch/arm/boot/dts/bcm2708-rpi-cm.dtsi
-+++ b/arch/arm/boot/dts/bcm2708-rpi-cm.dtsi
-@@ -36,6 +36,11 @@
- status = "okay";
- };
-
-+&audio {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&audio_pins>;
-+};
-+
- / {
- __overrides__ {
- core_freq = <&clk_core>,"clock-frequency:0";
diff --git a/target/linux/brcm2708/patches-4.4/0576-Add-overlay-for-mcp3008-adc-1818.patch b/target/linux/brcm2708/patches-4.4/0576-Add-overlay-for-mcp3008-adc-1818.patch
deleted file mode 100644
index 2715d7b..0000000
--- a/target/linux/brcm2708/patches-4.4/0576-Add-overlay-for-mcp3008-adc-1818.patch
+++ /dev/null
@@ -1,281 +0,0 @@
-From fbaf66882e8c247111a190d51c4f397092c8e65a Mon Sep 17 00:00:00 2001
-From: Scott Ellis <scott at jumpnowtek.com>
-Date: Fri, 27 Jan 2017 06:42:42 -0500
-Subject: [PATCH] Add overlay for mcp3008 adc (#1818)
-
-Some example usage:
-
-SPI0.0
-dtparam=spi=on
-dtoverlay=mcp3008:spi0-0-present
-
-SPI0.1
-dtparam=spi=on
-dtoverlay=mcp3008:spi0-1-present
-
-SPI0.0 and SPI0.1
-dtparam=spi=on
-dtoverlay=mcp3008:spi0-0-present,spi0-1-present
-
-SPI1.0
-dtparam=spi=on
-dtoverlay=spi1-1cs
-dtoverlay=mcp3008:spi1-0-present
-
-SPI1.2
-dtparam=spi=on
-dtoverlay=spi1-1cs:cs0_pin=16
-dtoverlay=mcp3008:spi1-0-present
-
-SPI1.0 and SPI1.1
-dtoverlay=spi1-2cs
-dtoverlay=mcp3008:spi1-0-present,spi1-1-present
-
-Changing the speed
-
-SPI0.0
-dtparam=spi=on
-dtoverlay=mcp3008:spi0-0-present,spi0-0-speed=2000000
----
- arch/arm/boot/dts/overlays/Makefile | 1 +
- arch/arm/boot/dts/overlays/README | 9 ++
- arch/arm/boot/dts/overlays/mcp3008-overlay.dts | 205 +++++++++++++++++++++++++
- 3 files changed, 215 insertions(+)
- create mode 100755 arch/arm/boot/dts/overlays/mcp3008-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -57,6 +57,7 @@ dtbo-$(RPI_DT_OVERLAYS) += mcp23017.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += mcp23s17.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += mcp2515-can0.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += mcp2515-can1.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += mcp3008.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += mmc.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += mz61581.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += pi3-act-led.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -736,6 +736,15 @@ Params: oscillator Clock fr
- interrupt GPIO for interrupt signal
-
-
-+Name: mcp3008
-+Info: Configures MCP3008 A/D converters
-+ For devices on spi1 or spi2, the interfaces should be enabled
-+ with one of the spi1-1/2/3cs and/or spi2-1/2/3cs overlays.
-+Load: dtoverlay=mcp3008,<param>[=<val>]
-+Params: spi<n>-<m>-present boolean, configure device at spi<n>, cs<m>
-+ spi<n>-<m>-speed integer, set the spi bus speed for this device
-+
-+
- Name: mmc
- Info: Selects the bcm2835-mmc SD/MMC driver, optionally with overclock
- Load: dtoverlay=mmc,<param>=<val>
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/mcp3008-overlay.dts
-@@ -0,0 +1,205 @@
-+/*
-+ * Device tree overlay for Microchip mcp3008 10-Bit A/D Converters
-+ */
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709";
-+
-+ fragment at 0 {
-+ target = <&spidev0>;
-+ __dormant__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ fragment at 1 {
-+ target = <&spidev1>;
-+ __dormant__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ fragment at 2 {
-+ target-path = "spi1/spidev at 0";
-+ __dormant__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ fragment at 3 {
-+ target-path = "spi1/spidev at 1";
-+ __dormant__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ fragment at 4 {
-+ target-path = "spi1/spidev at 2";
-+ __dormant__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ fragment at 5 {
-+ target-path = "spi2/spidev at 0";
-+ __dormant__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ fragment at 6 {
-+ target-path = "spi2/spidev at 1";
-+ __dormant__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ fragment at 7 {
-+ target-path = "spi2/spidev at 2";
-+ __dormant__ {
-+ status = "disabled";
-+ };
-+ };
-+
-+ fragment at 8 {
-+ target = <&spi0>;
-+ __dormant__ {
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ mcp3008_00: mcp3008 at 0 {
-+ compatible = "mcp3008";
-+ reg = <0>;
-+ spi-max-frequency = <1600000>;
-+ };
-+ };
-+ };
-+
-+ fragment at 9 {
-+ target = <&spi0>;
-+ __dormant__ {
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ mcp3008_01: mcp3008 at 1 {
-+ compatible = "mcp3008";
-+ reg = <1>;
-+ spi-max-frequency = <1600000>;
-+ };
-+ };
-+ };
-+
-+ fragment at 10 {
-+ target = <&spi1>;
-+ __dormant__ {
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ mcp3008_10: mcp3008 at 0 {
-+ compatible = "mcp3008";
-+ reg = <0>;
-+ spi-max-frequency = <1600000>;
-+ };
-+ };
-+ };
-+
-+ fragment at 11 {
-+ target = <&spi1>;
-+ __dormant__ {
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ mcp3008_11: mcp3008 at 1 {
-+ compatible = "mcp3008";
-+ reg = <1>;
-+ spi-max-frequency = <1600000>;
-+ };
-+ };
-+ };
-+
-+ fragment at 12 {
-+ target = <&spi1>;
-+ __dormant__ {
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ mcp3008_12: mcp3008 at 2 {
-+ compatible = "mcp3008";
-+ reg = <2>;
-+ spi-max-frequency = <1600000>;
-+ };
-+ };
-+ };
-+
-+ fragment at 13 {
-+ target = <&spi2>;
-+ __dormant__ {
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ mcp3008_20: mcp3008 at 0 {
-+ compatible = "mcp3008";
-+ reg = <0>;
-+ spi-max-frequency = <1600000>;
-+ };
-+ };
-+ };
-+
-+ fragment at 14 {
-+ target = <&spi2>;
-+ __dormant__ {
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ mcp3008_21: mcp3008 at 1 {
-+ compatible = "mcp3008";
-+ reg = <1>;
-+ spi-max-frequency = <1600000>;
-+ };
-+ };
-+ };
-+
-+ fragment at 15 {
-+ target = <&spi2>;
-+ __dormant__ {
-+ status = "okay";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ mcp3008_22: mcp3008 at 2 {
-+ compatible = "mcp3008";
-+ reg = <2>;
-+ spi-max-frequency = <1600000>;
-+ };
-+ };
-+ };
-+
-+ __overrides__ {
-+ spi0-0-present = <0>, "+0+8";
-+ spi0-1-present = <0>, "+1+9";
-+ spi1-0-present = <0>, "+2+10";
-+ spi1-1-present = <0>, "+3+11";
-+ spi1-2-present = <0>, "+4+12";
-+ spi2-0-present = <0>, "+5+13";
-+ spi2-1-present = <0>, "+6+14";
-+ spi2-2-present = <0>, "+7+15";
-+ spi0-0-speed = <&mcp3008_00>, "spi-max-frequency:0";
-+ spi0-1-speed = <&mcp3008_01>, "spi-max-frequency:0";
-+ spi1-0-speed = <&mcp3008_10>, "spi-max-frequency:0";
-+ spi1-1-speed = <&mcp3008_11>, "spi-max-frequency:0";
-+ spi1-2-speed = <&mcp3008_12>, "spi-max-frequency:0";
-+ spi2-0-speed = <&mcp3008_20>, "spi-max-frequency:0";
-+ spi2-1-speed = <&mcp3008_21>, "spi-max-frequency:0";
-+ spi2-2-speed = <&mcp3008_22>, "spi-max-frequency:0";
-+ };
-+};
diff --git a/target/linux/brcm2708/patches-4.4/0577-config-add-slcan-kernel-module.patch b/target/linux/brcm2708/patches-4.4/0577-config-add-slcan-kernel-module.patch
deleted file mode 100644
index 8e2cebb..0000000
--- a/target/linux/brcm2708/patches-4.4/0577-config-add-slcan-kernel-module.patch
+++ /dev/null
@@ -1,31 +0,0 @@
-From 58a5eac5f1d5849c4c64075cb0608788b35b1ba8 Mon Sep 17 00:00:00 2001
-From: popcornmix <popcornmix at gmail.com>
-Date: Fri, 27 Jan 2017 18:49:30 +0000
-Subject: [PATCH] config: add slcan kernel module
-
-See: https://github.com/raspberrypi/linux/issues/1819
----
- arch/arm/configs/bcm2709_defconfig | 1 +
- arch/arm/configs/bcmrpi_defconfig | 1 +
- 2 files changed, 2 insertions(+)
-
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -358,6 +358,7 @@ CONFIG_BAYCOM_SER_HDX=m
- CONFIG_YAM=m
- CONFIG_CAN=m
- CONFIG_CAN_VCAN=m
-+CONFIG_CAN_SLCAN=m
- CONFIG_CAN_MCP251X=m
- CONFIG_IRDA=m
- CONFIG_IRLAN=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -351,6 +351,7 @@ CONFIG_BAYCOM_SER_HDX=m
- CONFIG_YAM=m
- CONFIG_CAN=m
- CONFIG_CAN_VCAN=m
-+CONFIG_CAN_SLCAN=m
- CONFIG_CAN_MCP251X=m
- CONFIG_IRDA=m
- CONFIG_IRLAN=m
diff --git a/target/linux/brcm2708/patches-4.4/0578-drm-vc4-Fix-sending-of-page-flip-completion-events-i.patch b/target/linux/brcm2708/patches-4.4/0578-drm-vc4-Fix-sending-of-page-flip-completion-events-i.patch
deleted file mode 100644
index a94cde7..0000000
--- a/target/linux/brcm2708/patches-4.4/0578-drm-vc4-Fix-sending-of-page-flip-completion-events-i.patch
+++ /dev/null
@@ -1,42 +0,0 @@
-From 64e5b6a26eec44abb36eea964fc0ac35aeed6f26 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Thu, 2 Feb 2017 09:42:18 -0800
-Subject: [PATCH] drm/vc4: Fix sending of page flip completion events in FKMS
- mode.
-
-In the rewrite of vc4_crtc.c for fkms, I dropped the part of the
-CRTC's atomic flush handler that moved the completion event from the
-proposed atomic state change to the CRTC's current state. That meant
-that when full screen pageflipping happened (glxgears -fullscreen in
-X, compton, por weston), the app would end up blocked firever waiting
-to draw its next frame.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
----
- drivers/gpu/drm/vc4/vc4_firmware_kms.c | 15 +++++++++++++++
- 1 file changed, 15 insertions(+)
-
---- a/drivers/gpu/drm/vc4/vc4_firmware_kms.c
-+++ b/drivers/gpu/drm/vc4/vc4_firmware_kms.c
-@@ -312,6 +312,21 @@ static int vc4_crtc_atomic_check(struct
- static void vc4_crtc_atomic_flush(struct drm_crtc *crtc,
- struct drm_crtc_state *old_state)
- {
-+ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc);
-+ struct drm_device *dev = crtc->dev;
-+
-+ if (crtc->state->event) {
-+ unsigned long flags;
-+
-+ crtc->state->event->pipe = drm_crtc_index(crtc);
-+
-+ WARN_ON(drm_crtc_vblank_get(crtc) != 0);
-+
-+ spin_lock_irqsave(&dev->event_lock, flags);
-+ vc4_crtc->event = crtc->state->event;
-+ crtc->state->event = NULL;
-+ spin_unlock_irqrestore(&dev->event_lock, flags);
-+ }
- }
-
- static void vc4_crtc_handle_page_flip(struct vc4_crtc *vc4_crtc)
diff --git a/target/linux/brcm2708/patches-4.4/0579-clk-bcm2835-Fix-fixed_divider-of-pllh_aux.patch b/target/linux/brcm2708/patches-4.4/0579-clk-bcm2835-Fix-fixed_divider-of-pllh_aux.patch
deleted file mode 100644
index 19ff9b7..0000000
--- a/target/linux/brcm2708/patches-4.4/0579-clk-bcm2835-Fix-fixed_divider-of-pllh_aux.patch
+++ /dev/null
@@ -1,27 +0,0 @@
-From 7149466b737e35d58c92bf7e97539d86afa1d5ad Mon Sep 17 00:00:00 2001
-From: Boris Brezillon <boris.brezillon at free-electrons.com>
-Date: Tue, 22 Nov 2016 12:45:28 -0800
-Subject: [PATCH] clk: bcm2835: Fix ->fixed_divider of pllh_aux
-
-There is no fixed divider on pllh_aux.
-
-Signed-off-by: Boris Brezillon <boris.brezillon at free-electrons.com>
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
-(cherry picked from commit f2a46926aba1f0c33944901d2420a6a887455ddc)
----
- drivers/clk/bcm/clk-bcm2835.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/clk/bcm/clk-bcm2835.c
-+++ b/drivers/clk/bcm/clk-bcm2835.c
-@@ -1657,7 +1657,7 @@ static const struct bcm2835_clk_desc clk
- .a2w_reg = A2W_PLLH_AUX,
- .load_mask = CM_PLLH_LOADAUX,
- .hold_mask = 0,
-- .fixed_divider = 10),
-+ .fixed_divider = 1),
- [BCM2835_PLLH_PIX] = REGISTER_PLL_DIV(
- .name = "pllh_pix",
- .source_pll = "pllh",
diff --git a/target/linux/brcm2708/patches-4.4/0580-clk-bcm-Support-rate-change-propagation-on-bcm2835-c.patch b/target/linux/brcm2708/patches-4.4/0580-clk-bcm-Support-rate-change-propagation-on-bcm2835-c.patch
deleted file mode 100644
index 3bfce12..0000000
--- a/target/linux/brcm2708/patches-4.4/0580-clk-bcm-Support-rate-change-propagation-on-bcm2835-c.patch
+++ /dev/null
@@ -1,124 +0,0 @@
-From cc454cd7c20a0044a6a5a2ba949293b489c51598 Mon Sep 17 00:00:00 2001
-From: Boris Brezillon <boris.brezillon at free-electrons.com>
-Date: Thu, 1 Dec 2016 22:00:19 +0100
-Subject: [PATCH] clk: bcm: Support rate change propagation on bcm2835 clocks
-
-Some peripheral clocks, like the VEC (Video EnCoder) clock need to be set
-to a precise rate (in our case 108MHz). With the current implementation,
-where peripheral clocks are not allowed to forward rate change requests
-to their parents, it is impossible to match this requirement unless the
-bootloader has configured things correctly, or a specific rate has been
-assigned through the DT (with the assigned-clk-rates property).
-
-Add a new field to struct bcm2835_clock_data to specify which parent
-clocks accept rate change propagation, and support set rate propagation
-in bcm2835_clock_determine_rate().
-
-Signed-off-by: Boris Brezillon <boris.brezillon at free-electrons.com>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
-(cherry picked from commit 155e8b3b0ee320ae866b97dd31eba8a1f080a772)
----
- drivers/clk/bcm/clk-bcm2835.c | 67 ++++++++++++++++++++++++++++++++++++++++---
- 1 file changed, 63 insertions(+), 4 deletions(-)
-
---- a/drivers/clk/bcm/clk-bcm2835.c
-+++ b/drivers/clk/bcm/clk-bcm2835.c
-@@ -457,6 +457,9 @@ struct bcm2835_clock_data {
- const char *const *parents;
- int num_mux_parents;
-
-+ /* Bitmap encoding which parents accept rate change propagation. */
-+ unsigned int set_rate_parent;
-+
- u32 ctl_reg;
- u32 div_reg;
-
-@@ -1055,10 +1058,60 @@ bcm2835_clk_is_pllc(struct clk_hw *hw)
- return strncmp(clk_hw_get_name(hw), "pllc", 4) == 0;
- }
-
-+static unsigned long bcm2835_clock_choose_div_and_prate(struct clk_hw *hw,
-+ int parent_idx,
-+ unsigned long rate,
-+ u32 *div,
-+ unsigned long *prate)
-+{
-+ struct bcm2835_clock *clock = bcm2835_clock_from_hw(hw);
-+ struct bcm2835_cprman *cprman = clock->cprman;
-+ const struct bcm2835_clock_data *data = clock->data;
-+ unsigned long best_rate;
-+ u32 curdiv, mindiv, maxdiv;
-+ struct clk_hw *parent;
-+
-+ parent = clk_hw_get_parent_by_index(hw, parent_idx);
-+
-+ if (!(BIT(parent_idx) & data->set_rate_parent)) {
-+ *prate = clk_hw_get_rate(parent);
-+ *div = bcm2835_clock_choose_div(hw, rate, *prate, true);
-+
-+ return bcm2835_clock_rate_from_divisor(clock, *prate,
-+ *div);
-+ }
-+
-+ if (data->frac_bits)
-+ dev_warn(cprman->dev,
-+ "frac bits are not used when propagating rate change");
-+
-+ /* clamp to min divider of 2 if we're dealing with a mash clock */
-+ mindiv = data->is_mash_clock ? 2 : 1;
-+ maxdiv = BIT(data->int_bits) - 1;
-+
-+ /* TODO: Be smart, and only test a subset of the available divisors. */
-+ for (curdiv = mindiv; curdiv <= maxdiv; curdiv++) {
-+ unsigned long tmp_rate;
-+
-+ tmp_rate = clk_hw_round_rate(parent, rate * curdiv);
-+ tmp_rate /= curdiv;
-+ if (curdiv == mindiv ||
-+ (tmp_rate > best_rate && tmp_rate <= rate))
-+ best_rate = tmp_rate;
-+
-+ if (best_rate == rate)
-+ break;
-+ }
-+
-+ *div = curdiv << CM_DIV_FRAC_BITS;
-+ *prate = curdiv * best_rate;
-+
-+ return best_rate;
-+}
-+
- static int bcm2835_clock_determine_rate(struct clk_hw *hw,
- struct clk_rate_request *req)
- {
-- struct bcm2835_clock *clock = bcm2835_clock_from_hw(hw);
- struct clk_hw *parent, *best_parent = NULL;
- bool current_parent_is_pllc;
- unsigned long rate, best_rate = 0;
-@@ -1086,9 +1139,8 @@ static int bcm2835_clock_determine_rate(
- if (bcm2835_clk_is_pllc(parent) && !current_parent_is_pllc)
- continue;
-
-- prate = clk_hw_get_rate(parent);
-- div = bcm2835_clock_choose_div(hw, req->rate, prate, true);
-- rate = bcm2835_clock_rate_from_divisor(clock, prate, div);
-+ rate = bcm2835_clock_choose_div_and_prate(hw, i, req->rate,
-+ &div, &prate);
- if (rate > best_rate && rate <= req->rate) {
- best_parent = parent;
- best_prate = prate;
-@@ -1308,6 +1360,13 @@ static struct clk *bcm2835_register_cloc
- if ((cprman_read(cprman, data->ctl_reg) & CM_ENABLE) == 0)
- init.flags &= ~CLK_IS_CRITICAL;
-
-+ /*
-+ * Pass the CLK_SET_RATE_PARENT flag if we are allowed to propagate
-+ * rate changes on at least of the parents.
-+ */
-+ if (data->set_rate_parent)
-+ init.flags |= CLK_SET_RATE_PARENT;
-+
- if (data->is_vpu_clock) {
- init.ops = &bcm2835_vpu_clock_clk_ops;
- } else {
diff --git a/target/linux/brcm2708/patches-4.4/0581-clk-bcm-Allow-rate-change-propagation-to-PLLH_AUX-on.patch b/target/linux/brcm2708/patches-4.4/0581-clk-bcm-Allow-rate-change-propagation-to-PLLH_AUX-on.patch
deleted file mode 100644
index 4b22762..0000000
--- a/target/linux/brcm2708/patches-4.4/0581-clk-bcm-Allow-rate-change-propagation-to-PLLH_AUX-on.patch
+++ /dev/null
@@ -1,35 +0,0 @@
-From e7a3b8bd6756b59696a430a0c83e3e609915dea6 Mon Sep 17 00:00:00 2001
-From: Boris Brezillon <boris.brezillon at free-electrons.com>
-Date: Thu, 1 Dec 2016 22:00:20 +0100
-Subject: [PATCH] clk: bcm: Allow rate change propagation to PLLH_AUX on VEC
- clock
-
-The VEC clock requires needs to be set at exactly 108MHz. Allow rate
-change propagation on PLLH_AUX to match this requirement wihtout
-impacting other IPs (PLLH is currently only used by the HDMI encoder,
-which cannot be enabled when the VEC encoder is enabled).
-
-Signed-off-by: Boris Brezillon <boris.brezillon at free-electrons.com>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
-(cherry picked from commit d86d46af84855403c00018be1c3e7bc190f2a6cd)
----
- drivers/clk/bcm/clk-bcm2835.c | 7 ++++++-
- 1 file changed, 6 insertions(+), 1 deletion(-)
-
---- a/drivers/clk/bcm/clk-bcm2835.c
-+++ b/drivers/clk/bcm/clk-bcm2835.c
-@@ -1920,7 +1920,12 @@ static const struct bcm2835_clk_desc clk
- .ctl_reg = CM_VECCTL,
- .div_reg = CM_VECDIV,
- .int_bits = 4,
-- .frac_bits = 0),
-+ .frac_bits = 0,
-+ /*
-+ * Allow rate change propagation only on PLLH_AUX which is
-+ * assigned index 7 in the parent array.
-+ */
-+ .set_rate_parent = BIT(7)),
-
- /* dsi clocks */
- [BCM2835_CLOCK_DSI0E] = REGISTER_PER_CLK(
diff --git a/target/linux/brcm2708/patches-4.4/0582-clk-bcm-Fix-maybe-uninitialized-warning-in-bcm2835_c.patch b/target/linux/brcm2708/patches-4.4/0582-clk-bcm-Fix-maybe-uninitialized-warning-in-bcm2835_c.patch
deleted file mode 100644
index 41771a5..0000000
--- a/target/linux/brcm2708/patches-4.4/0582-clk-bcm-Fix-maybe-uninitialized-warning-in-bcm2835_c.patch
+++ /dev/null
@@ -1,29 +0,0 @@
-From 6c42e5b8e25911b5fd39207d1a3b059adecfe346 Mon Sep 17 00:00:00 2001
-From: Boris Brezillon <boris.brezillon at free-electrons.com>
-Date: Mon, 12 Dec 2016 09:00:53 +0100
-Subject: [PATCH] clk: bcm: Fix 'maybe-uninitialized' warning in
- bcm2835_clock_choose_div_and_prate()
-
-best_rate is reported as potentially uninitialized by gcc.
-
-Signed-off-by: Boris Brezillon <boris.brezillon at free-electrons.com>
-Fixes: 155e8b3b0ee3 ("clk: bcm: Support rate change propagation on bcm2835 clocks")
-Reported-by: Stephen Rothwell <sfr at canb.auug.org.au>
-Reviewed-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
-(cherry picked from commit 2aab7a2055a1705c9e30920d95a596226999eb21)
----
- drivers/clk/bcm/clk-bcm2835.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/clk/bcm/clk-bcm2835.c
-+++ b/drivers/clk/bcm/clk-bcm2835.c
-@@ -1067,7 +1067,7 @@ static unsigned long bcm2835_clock_choos
- struct bcm2835_clock *clock = bcm2835_clock_from_hw(hw);
- struct bcm2835_cprman *cprman = clock->cprman;
- const struct bcm2835_clock_data *data = clock->data;
-- unsigned long best_rate;
-+ unsigned long best_rate = 0;
- u32 curdiv, mindiv, maxdiv;
- struct clk_hw *parent;
-
diff --git a/target/linux/brcm2708/patches-4.4/0583-clk-bcm2835-Don-t-rate-change-PLLs-on-behalf-of-DSI-.patch b/target/linux/brcm2708/patches-4.4/0583-clk-bcm2835-Don-t-rate-change-PLLs-on-behalf-of-DSI-.patch
deleted file mode 100644
index b267edc..0000000
--- a/target/linux/brcm2708/patches-4.4/0583-clk-bcm2835-Don-t-rate-change-PLLs-on-behalf-of-DSI-.patch
+++ /dev/null
@@ -1,172 +0,0 @@
-From 07fed713270af298f1ba3cfdc128d29102ecb707 Mon Sep 17 00:00:00 2001
-From: Eric Anholt <eric at anholt.net>
-Date: Wed, 18 Jan 2017 07:31:55 +1100
-Subject: [PATCH] clk: bcm2835: Don't rate change PLLs on behalf of DSI PLL
- dividers (v2).
-
-Our core PLLs are intended to be configured once and left alone. With
-the SET_RATE_PARENT, asking to set the PLLD_DSI1 clock rate would
-change PLLD just to get closer to the requested DSI clock, thus
-changing PLLD_PER, the UART and ethernet PHY clock rates downstream of
-it, and breaking ethernet.
-
-We *do* want PLLH to change so that PLLH_AUX can be exactly the value
-we want, though. Thus, we need to have a per-divider policy of
-whether to pass rate changes up.
-
-Signed-off-by: Eric Anholt <eric at anholt.net>
-Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
-(cherry picked from commit 55486091bd1e1c5ed28c43c0d6b3392468a9adb5)
----
- drivers/clk/bcm/clk-bcm2835.c | 42 ++++++++++++++++++++++++++++--------------
- 1 file changed, 28 insertions(+), 14 deletions(-)
-
---- a/drivers/clk/bcm/clk-bcm2835.c
-+++ b/drivers/clk/bcm/clk-bcm2835.c
-@@ -449,6 +449,7 @@ struct bcm2835_pll_divider_data {
- u32 load_mask;
- u32 hold_mask;
- u32 fixed_divider;
-+ u32 flags;
- };
-
- struct bcm2835_clock_data {
-@@ -1286,7 +1287,7 @@ bcm2835_register_pll_divider(struct bcm2
- init.num_parents = 1;
- init.name = divider_name;
- init.ops = &bcm2835_pll_divider_clk_ops;
-- init.flags = CLK_IGNORE_UNUSED;
-+ init.flags = data->flags | CLK_IGNORE_UNUSED;
-
- divider = devm_kzalloc(cprman->dev, sizeof(*divider), GFP_KERNEL);
- if (!divider)
-@@ -1525,7 +1526,8 @@ static const struct bcm2835_clk_desc clk
- .a2w_reg = A2W_PLLA_CORE,
- .load_mask = CM_PLLA_LOADCORE,
- .hold_mask = CM_PLLA_HOLDCORE,
-- .fixed_divider = 1),
-+ .fixed_divider = 1,
-+ .flags = CLK_SET_RATE_PARENT),
- [BCM2835_PLLA_PER] = REGISTER_PLL_DIV(
- .name = "plla_per",
- .source_pll = "plla",
-@@ -1533,7 +1535,8 @@ static const struct bcm2835_clk_desc clk
- .a2w_reg = A2W_PLLA_PER,
- .load_mask = CM_PLLA_LOADPER,
- .hold_mask = CM_PLLA_HOLDPER,
-- .fixed_divider = 1),
-+ .fixed_divider = 1,
-+ .flags = CLK_SET_RATE_PARENT),
- [BCM2835_PLLA_DSI0] = REGISTER_PLL_DIV(
- .name = "plla_dsi0",
- .source_pll = "plla",
-@@ -1549,7 +1552,8 @@ static const struct bcm2835_clk_desc clk
- .a2w_reg = A2W_PLLA_CCP2,
- .load_mask = CM_PLLA_LOADCCP2,
- .hold_mask = CM_PLLA_HOLDCCP2,
-- .fixed_divider = 1),
-+ .fixed_divider = 1,
-+ .flags = CLK_SET_RATE_PARENT),
-
- /* PLLB is used for the ARM's clock. */
- [BCM2835_PLLB] = REGISTER_PLL(
-@@ -1573,7 +1577,8 @@ static const struct bcm2835_clk_desc clk
- .a2w_reg = A2W_PLLB_ARM,
- .load_mask = CM_PLLB_LOADARM,
- .hold_mask = CM_PLLB_HOLDARM,
-- .fixed_divider = 1),
-+ .fixed_divider = 1,
-+ .flags = CLK_SET_RATE_PARENT),
-
- /*
- * PLLC is the core PLL, used to drive the core VPU clock.
-@@ -1602,7 +1607,8 @@ static const struct bcm2835_clk_desc clk
- .a2w_reg = A2W_PLLC_CORE0,
- .load_mask = CM_PLLC_LOADCORE0,
- .hold_mask = CM_PLLC_HOLDCORE0,
-- .fixed_divider = 1),
-+ .fixed_divider = 1,
-+ .flags = CLK_SET_RATE_PARENT),
- [BCM2835_PLLC_CORE1] = REGISTER_PLL_DIV(
- .name = "pllc_core1",
- .source_pll = "pllc",
-@@ -1610,7 +1616,8 @@ static const struct bcm2835_clk_desc clk
- .a2w_reg = A2W_PLLC_CORE1,
- .load_mask = CM_PLLC_LOADCORE1,
- .hold_mask = CM_PLLC_HOLDCORE1,
-- .fixed_divider = 1),
-+ .fixed_divider = 1,
-+ .flags = CLK_SET_RATE_PARENT),
- [BCM2835_PLLC_CORE2] = REGISTER_PLL_DIV(
- .name = "pllc_core2",
- .source_pll = "pllc",
-@@ -1618,7 +1625,8 @@ static const struct bcm2835_clk_desc clk
- .a2w_reg = A2W_PLLC_CORE2,
- .load_mask = CM_PLLC_LOADCORE2,
- .hold_mask = CM_PLLC_HOLDCORE2,
-- .fixed_divider = 1),
-+ .fixed_divider = 1,
-+ .flags = CLK_SET_RATE_PARENT),
- [BCM2835_PLLC_PER] = REGISTER_PLL_DIV(
- .name = "pllc_per",
- .source_pll = "pllc",
-@@ -1626,7 +1634,8 @@ static const struct bcm2835_clk_desc clk
- .a2w_reg = A2W_PLLC_PER,
- .load_mask = CM_PLLC_LOADPER,
- .hold_mask = CM_PLLC_HOLDPER,
-- .fixed_divider = 1),
-+ .fixed_divider = 1,
-+ .flags = CLK_SET_RATE_PARENT),
-
- /*
- * PLLD is the display PLL, used to drive DSI display panels.
-@@ -1655,7 +1664,8 @@ static const struct bcm2835_clk_desc clk
- .a2w_reg = A2W_PLLD_CORE,
- .load_mask = CM_PLLD_LOADCORE,
- .hold_mask = CM_PLLD_HOLDCORE,
-- .fixed_divider = 1),
-+ .fixed_divider = 1,
-+ .flags = CLK_SET_RATE_PARENT),
- [BCM2835_PLLD_PER] = REGISTER_PLL_DIV(
- .name = "plld_per",
- .source_pll = "plld",
-@@ -1663,7 +1673,8 @@ static const struct bcm2835_clk_desc clk
- .a2w_reg = A2W_PLLD_PER,
- .load_mask = CM_PLLD_LOADPER,
- .hold_mask = CM_PLLD_HOLDPER,
-- .fixed_divider = 1),
-+ .fixed_divider = 1,
-+ .flags = CLK_SET_RATE_PARENT),
- [BCM2835_PLLD_DSI0] = REGISTER_PLL_DIV(
- .name = "plld_dsi0",
- .source_pll = "plld",
-@@ -1708,7 +1719,8 @@ static const struct bcm2835_clk_desc clk
- .a2w_reg = A2W_PLLH_RCAL,
- .load_mask = CM_PLLH_LOADRCAL,
- .hold_mask = 0,
-- .fixed_divider = 10),
-+ .fixed_divider = 10,
-+ .flags = CLK_SET_RATE_PARENT),
- [BCM2835_PLLH_AUX] = REGISTER_PLL_DIV(
- .name = "pllh_aux",
- .source_pll = "pllh",
-@@ -1716,7 +1728,8 @@ static const struct bcm2835_clk_desc clk
- .a2w_reg = A2W_PLLH_AUX,
- .load_mask = CM_PLLH_LOADAUX,
- .hold_mask = 0,
-- .fixed_divider = 1),
-+ .fixed_divider = 1,
-+ .flags = CLK_SET_RATE_PARENT),
- [BCM2835_PLLH_PIX] = REGISTER_PLL_DIV(
- .name = "pllh_pix",
- .source_pll = "pllh",
-@@ -1724,7 +1737,8 @@ static const struct bcm2835_clk_desc clk
- .a2w_reg = A2W_PLLH_PIX,
- .load_mask = CM_PLLH_LOADPIX,
- .hold_mask = 0,
-- .fixed_divider = 10),
-+ .fixed_divider = 10,
-+ .flags = CLK_SET_RATE_PARENT),
-
- /* the clocks */
-
diff --git a/target/linux/brcm2708/patches-4.4/0584-gpio_mem-Remove-unnecessary-dev_info-output-1830.patch b/target/linux/brcm2708/patches-4.4/0584-gpio_mem-Remove-unnecessary-dev_info-output-1830.patch
deleted file mode 100644
index c2f7c89..0000000
--- a/target/linux/brcm2708/patches-4.4/0584-gpio_mem-Remove-unnecessary-dev_info-output-1830.patch
+++ /dev/null
@@ -1,22 +0,0 @@
-From abf88336cae2463bb38104a75e2fea7b5c2aa1f7 Mon Sep 17 00:00:00 2001
-From: JamesH65 <JamesH65 at users.noreply.github.com>
-Date: Mon, 6 Feb 2017 15:24:47 +0000
-Subject: [PATCH] gpio_mem: Remove unnecessary dev_info output (#1830)
-
-The open function was spamming syslog every time
-called, so have removed call completely.
----
- drivers/char/broadcom/bcm2835-gpiomem.c | 2 --
- 1 file changed, 2 deletions(-)
-
---- a/drivers/char/broadcom/bcm2835-gpiomem.c
-+++ b/drivers/char/broadcom/bcm2835-gpiomem.c
-@@ -76,8 +76,6 @@ static int bcm2835_gpiomem_open(struct i
- int dev = iminor(inode);
- int ret = 0;
-
-- dev_info(inst->dev, "gpiomem device opened.");
--
- if (dev != DEVICE_MINOR) {
- dev_err(inst->dev, "Unknown minor device: %d", dev);
- ret = -ENXIO;
diff --git a/target/linux/brcm2708/patches-4.4/1000-mfd-rpisense-disable.patch b/target/linux/brcm2708/patches-4.4/1000-mfd-rpisense-disable.patch
deleted file mode 100644
index 164e844..0000000
--- a/target/linux/brcm2708/patches-4.4/1000-mfd-rpisense-disable.patch
+++ /dev/null
@@ -1,10 +0,0 @@
---- a/drivers/mfd/Kconfig
-+++ b/drivers/mfd/Kconfig
-@@ -13,6 +13,7 @@ config MFD_CORE
- config MFD_RPISENSE_CORE
- tristate "Raspberry Pi Sense HAT core functions"
- depends on I2C
-+ depends on BROKEN
- select MFD_CORE
- help
- This is the core driver for the Raspberry Pi Sense HAT. This provides
More information about the lede-commits
mailing list