[source] bcm53xx: backport Broadcom's iProc QSPI driver
LEDE Commits
lede-commits at lists.infradead.org
Tue Feb 28 22:05:49 PST 2017
rmilecki pushed a commit to source.git, branch master:
https://git.lede-project.org/9209511d61fce02b0af48b44d963150e076e0f7e
commit 9209511d61fce02b0af48b44d963150e076e0f7e
Author: Rafał Miłecki <rafal at milecki.pl>
AuthorDate: Wed Mar 1 06:52:23 2017 +0100
bcm53xx: backport Broadcom's iProc QSPI driver
This driver has been added instead of improving spi-bcm53xx. It has some
advantages: allows SPI speed control & hopefully doesn't have bug that
was stopping us from using multiple SPI messages for writing flash data.
Signed-off-by: Rafał Miłecki <rafal at milecki.pl>
---
target/linux/bcm53xx/config-4.4 | 1 +
...001-spi-bcm-qspi-Add-Broadcom-MSPI-driver.patch | 832 +++++++++++++++++++++
...mstb-qspi-Broadcom-settop-platform-driver.patch | 84 +++
...i-Add-BSPI-spi-nor-flash-controller-drive.patch | 780 +++++++++++++++++++
...pi-bcm-qspi-don-t-include-linux-mtd-cfi.h.patch | 27 +
...005-spi-bcm-qspi-fix-suspend-resume-ifdef.patch | 63 ++
...i-Fix-return-value-check-in-bcm_qspi_prob.patch | 29 +
...i-Fix-error-return-code-in-bcm_qspi_probe.patch | 32 +
...proc-qspi-Add-Broadcom-iProc-SoCs-support.patch | 452 +++++++++++
9 files changed, 2300 insertions(+)
diff --git a/target/linux/bcm53xx/config-4.4 b/target/linux/bcm53xx/config-4.4
index 723d16a..a7675e4 100644
--- a/target/linux/bcm53xx/config-4.4
+++ b/target/linux/bcm53xx/config-4.4
@@ -298,6 +298,7 @@ CONFIG_SMP_ON_UP=y
CONFIG_SPARSE_IRQ=y
CONFIG_SPI=y
CONFIG_SPI_BCM53XX=y
+# CONFIG_SPI_BCM_QSPI is not set
CONFIG_SPI_BITBANG=y
CONFIG_SPI_GPIO=y
CONFIG_SPI_MASTER=y
diff --git a/target/linux/bcm53xx/patches-4.4/083-0001-spi-bcm-qspi-Add-Broadcom-MSPI-driver.patch b/target/linux/bcm53xx/patches-4.4/083-0001-spi-bcm-qspi-Add-Broadcom-MSPI-driver.patch
new file mode 100644
index 0000000..b10ba83
--- /dev/null
+++ b/target/linux/bcm53xx/patches-4.4/083-0001-spi-bcm-qspi-Add-Broadcom-MSPI-driver.patch
@@ -0,0 +1,832 @@
+From fa236a7ef24048bafaeed13f68df35a819794758 Mon Sep 17 00:00:00 2001
+From: Kamal Dasu <kdasu.kdev at gmail.com>
+Date: Wed, 24 Aug 2016 18:04:23 -0400
+Subject: [PATCH] spi: bcm-qspi: Add Broadcom MSPI driver
+
+Master SPI driver for Broadcom settop, iProc SoCs. The driver
+is used for devices that use SPI protocol on BRCMSTB, NSP, NS2
+SoCs. SoC platform driver call exported porbe(), remove()
+and suspend/resume pm_ops implemented in this common driver.
+
+Signed-off-by: Kamal Dasu <kdasu.kdev at gmail.com>
+Signed-off-by: Yendapally Reddy Dhananjaya Reddy
+Signed-off-by: Mark Brown <broonie at kernel.org>
+---
+ drivers/spi/Kconfig | 10 +
+ drivers/spi/Makefile | 1 +
+ drivers/spi/spi-bcm-qspi.c | 712 +++++++++++++++++++++++++++++++++++++++++++++
+ drivers/spi/spi-bcm-qspi.h | 63 ++++
+ 4 files changed, 786 insertions(+)
+ create mode 100644 drivers/spi/spi-bcm-qspi.c
+ create mode 100644 drivers/spi/spi-bcm-qspi.h
+
+--- a/drivers/spi/Kconfig
++++ b/drivers/spi/Kconfig
+@@ -147,6 +147,16 @@ config SPI_BCM63XX_HSSPI
+ This enables support for the High Speed SPI controller present on
+ newer Broadcom BCM63XX SoCs.
+
++config SPI_BCM_QSPI
++ tristate "Broadcom BSPI and MSPI controller support"
++ depends on ARCH_BRCMSTB || ARCH_BCM || ARCH_BCM_IPROC || COMPILE_TEST
++ default ARCH_BCM_IPROC
++ help
++ Enables support for the Broadcom SPI flash and MSPI controller.
++ Select this option for any one of BRCMSTB, iProc NSP and NS2 SoCs
++ based platforms. This driver works for both SPI master for spi-nor
++ flash device as well as MSPI device.
++
+ config SPI_BITBANG
+ tristate "Utilities for Bitbanging SPI masters"
+ help
+--- a/drivers/spi/Makefile
++++ b/drivers/spi/Makefile
+@@ -19,6 +19,7 @@ obj-$(CONFIG_SPI_BCM2835AUX) += spi-bcm
+ obj-$(CONFIG_SPI_BCM53XX) += spi-bcm53xx.o
+ obj-$(CONFIG_SPI_BCM63XX) += spi-bcm63xx.o
+ obj-$(CONFIG_SPI_BCM63XX_HSSPI) += spi-bcm63xx-hsspi.o
++obj-$(CONFIG_SPI_BCM_QSPI) += spi-bcm-qspi.o
+ obj-$(CONFIG_SPI_BFIN5XX) += spi-bfin5xx.o
+ obj-$(CONFIG_SPI_ADI_V3) += spi-adi-v3.o
+ obj-$(CONFIG_SPI_BFIN_SPORT) += spi-bfin-sport.o
+--- /dev/null
++++ b/drivers/spi/spi-bcm-qspi.c
+@@ -0,0 +1,712 @@
++/*
++ * Driver for Broadcom BRCMSTB, NSP, NS2, Cygnus SPI Controllers
++ *
++ * Copyright 2016 Broadcom
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License, version 2, as
++ * published by the Free Software Foundation (the "GPL").
++ *
++ * This program is distributed in the hope that it will be useful, but
++ * WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
++ * General Public License version 2 (GPLv2) for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * version 2 (GPLv2) along with this source code.
++ */
++
++#include <linux/clk.h>
++#include <linux/delay.h>
++#include <linux/device.h>
++#include <linux/init.h>
++#include <linux/interrupt.h>
++#include <linux/io.h>
++#include <linux/ioport.h>
++#include <linux/kernel.h>
++#include <linux/module.h>
++#include <linux/mtd/cfi.h>
++#include <linux/mtd/spi-nor.h>
++#include <linux/of.h>
++#include <linux/of_irq.h>
++#include <linux/platform_device.h>
++#include <linux/slab.h>
++#include <linux/spi/spi.h>
++#include <linux/sysfs.h>
++#include <linux/types.h>
++#include "spi-bcm-qspi.h"
++
++#define DRIVER_NAME "bcm_qspi"
++
++/* MSPI register offsets */
++#define MSPI_SPCR0_LSB 0x000
++#define MSPI_SPCR0_MSB 0x004
++#define MSPI_SPCR1_LSB 0x008
++#define MSPI_SPCR1_MSB 0x00c
++#define MSPI_NEWQP 0x010
++#define MSPI_ENDQP 0x014
++#define MSPI_SPCR2 0x018
++#define MSPI_MSPI_STATUS 0x020
++#define MSPI_CPTQP 0x024
++#define MSPI_SPCR3 0x028
++#define MSPI_TXRAM 0x040
++#define MSPI_RXRAM 0x0c0
++#define MSPI_CDRAM 0x140
++#define MSPI_WRITE_LOCK 0x180
++
++#define MSPI_MASTER_BIT BIT(7)
++
++#define MSPI_NUM_CDRAM 16
++#define MSPI_CDRAM_CONT_BIT BIT(7)
++#define MSPI_CDRAM_BITSE_BIT BIT(6)
++#define MSPI_CDRAM_PCS 0xf
++
++#define MSPI_SPCR2_SPE BIT(6)
++#define MSPI_SPCR2_CONT_AFTER_CMD BIT(7)
++
++#define MSPI_MSPI_STATUS_SPIF BIT(0)
++
++#define INTR_BASE_BIT_SHIFT 0x02
++#define INTR_COUNT 0x07
++
++#define NUM_CHIPSELECT 4
++#define QSPI_SPBR_MIN 8U
++#define QSPI_SPBR_MAX 255U
++
++#define OPCODE_DIOR 0xBB
++#define OPCODE_QIOR 0xEB
++#define OPCODE_DIOR_4B 0xBC
++#define OPCODE_QIOR_4B 0xEC
++
++#define MAX_CMD_SIZE 6
++
++#define ADDR_4MB_MASK GENMASK(22, 0)
++
++/* stop at end of transfer, no other reason */
++#define TRANS_STATUS_BREAK_NONE 0
++/* stop at end of spi_message */
++#define TRANS_STATUS_BREAK_EOM 1
++/* stop at end of spi_transfer if delay */
++#define TRANS_STATUS_BREAK_DELAY 2
++/* stop at end of spi_transfer if cs_change */
++#define TRANS_STATUS_BREAK_CS_CHANGE 4
++/* stop if we run out of bytes */
++#define TRANS_STATUS_BREAK_NO_BYTES 8
++
++/* events that make us stop filling TX slots */
++#define TRANS_STATUS_BREAK_TX (TRANS_STATUS_BREAK_EOM | \
++ TRANS_STATUS_BREAK_DELAY | \
++ TRANS_STATUS_BREAK_CS_CHANGE)
++
++/* events that make us deassert CS */
++#define TRANS_STATUS_BREAK_DESELECT (TRANS_STATUS_BREAK_EOM | \
++ TRANS_STATUS_BREAK_CS_CHANGE)
++
++struct bcm_qspi_parms {
++ u32 speed_hz;
++ u8 mode;
++ u8 bits_per_word;
++};
++
++enum base_type {
++ MSPI,
++ CHIP_SELECT,
++ BASEMAX,
++};
++
++struct bcm_qspi_irq {
++ const char *irq_name;
++ const irq_handler_t irq_handler;
++ u32 mask;
++};
++
++struct bcm_qspi_dev_id {
++ const struct bcm_qspi_irq *irqp;
++ void *dev;
++};
++
++struct qspi_trans {
++ struct spi_transfer *trans;
++ int byte;
++};
++
++struct bcm_qspi {
++ struct platform_device *pdev;
++ struct spi_master *master;
++ struct clk *clk;
++ u32 base_clk;
++ u32 max_speed_hz;
++ void __iomem *base[BASEMAX];
++ struct bcm_qspi_parms last_parms;
++ struct qspi_trans trans_pos;
++ int curr_cs;
++ u32 s3_strap_override_ctrl;
++ bool big_endian;
++ int num_irqs;
++ struct bcm_qspi_dev_id *dev_ids;
++ struct completion mspi_done;
++};
++
++/* Read qspi controller register*/
++static inline u32 bcm_qspi_read(struct bcm_qspi *qspi, enum base_type type,
++ unsigned int offset)
++{
++ return bcm_qspi_readl(qspi->big_endian, qspi->base[type] + offset);
++}
++
++/* Write qspi controller register*/
++static inline void bcm_qspi_write(struct bcm_qspi *qspi, enum base_type type,
++ unsigned int offset, unsigned int data)
++{
++ bcm_qspi_writel(qspi->big_endian, data, qspi->base[type] + offset);
++}
++
++static void bcm_qspi_chip_select(struct bcm_qspi *qspi, int cs)
++{
++ u32 data = 0;
++
++ if (qspi->curr_cs == cs)
++ return;
++ if (qspi->base[CHIP_SELECT]) {
++ data = bcm_qspi_read(qspi, CHIP_SELECT, 0);
++ data = (data & ~0xff) | (1 << cs);
++ bcm_qspi_write(qspi, CHIP_SELECT, 0, data);
++ usleep_range(10, 20);
++ }
++ qspi->curr_cs = cs;
++}
++
++/* MSPI helpers */
++static void bcm_qspi_hw_set_parms(struct bcm_qspi *qspi,
++ const struct bcm_qspi_parms *xp)
++{
++ u32 spcr, spbr = 0;
++
++ if (xp->speed_hz)
++ spbr = qspi->base_clk / (2 * xp->speed_hz);
++
++ spcr = clamp_val(spbr, QSPI_SPBR_MIN, QSPI_SPBR_MAX);
++ bcm_qspi_write(qspi, MSPI, MSPI_SPCR0_LSB, spcr);
++
++ spcr = MSPI_MASTER_BIT;
++ /* for 16 bit the data should be zero */
++ if (xp->bits_per_word != 16)
++ spcr |= xp->bits_per_word << 2;
++ spcr |= xp->mode & 3;
++ bcm_qspi_write(qspi, MSPI, MSPI_SPCR0_MSB, spcr);
++
++ qspi->last_parms = *xp;
++}
++
++static void bcm_qspi_update_parms(struct bcm_qspi *qspi,
++ struct spi_device *spi,
++ struct spi_transfer *trans)
++{
++ struct bcm_qspi_parms xp;
++
++ xp.speed_hz = trans->speed_hz;
++ xp.bits_per_word = trans->bits_per_word;
++ xp.mode = spi->mode;
++
++ bcm_qspi_hw_set_parms(qspi, &xp);
++}
++
++static int bcm_qspi_setup(struct spi_device *spi)
++{
++ struct bcm_qspi_parms *xp;
++
++ if (spi->bits_per_word > 16)
++ return -EINVAL;
++
++ xp = spi_get_ctldata(spi);
++ if (!xp) {
++ xp = kzalloc(sizeof(*xp), GFP_KERNEL);
++ if (!xp)
++ return -ENOMEM;
++ spi_set_ctldata(spi, xp);
++ }
++ xp->speed_hz = spi->max_speed_hz;
++ xp->mode = spi->mode;
++
++ if (spi->bits_per_word)
++ xp->bits_per_word = spi->bits_per_word;
++ else
++ xp->bits_per_word = 8;
++
++ return 0;
++}
++
++static int update_qspi_trans_byte_count(struct bcm_qspi *qspi,
++ struct qspi_trans *qt, int flags)
++{
++ int ret = TRANS_STATUS_BREAK_NONE;
++
++ /* count the last transferred bytes */
++ if (qt->trans->bits_per_word <= 8)
++ qt->byte++;
++ else
++ qt->byte += 2;
++
++ if (qt->byte >= qt->trans->len) {
++ /* we're at the end of the spi_transfer */
++
++ /* in TX mode, need to pause for a delay or CS change */
++ if (qt->trans->delay_usecs &&
++ (flags & TRANS_STATUS_BREAK_DELAY))
++ ret |= TRANS_STATUS_BREAK_DELAY;
++ if (qt->trans->cs_change &&
++ (flags & TRANS_STATUS_BREAK_CS_CHANGE))
++ ret |= TRANS_STATUS_BREAK_CS_CHANGE;
++ if (ret)
++ goto done;
++
++ dev_dbg(&qspi->pdev->dev, "advance msg exit\n");
++ if (spi_transfer_is_last(qspi->master, qt->trans))
++ ret = TRANS_STATUS_BREAK_EOM;
++ else
++ ret = TRANS_STATUS_BREAK_NO_BYTES;
++
++ qt->trans = NULL;
++ }
++
++done:
++ dev_dbg(&qspi->pdev->dev, "trans %p len %d byte %d ret %x\n",
++ qt->trans, qt->trans ? qt->trans->len : 0, qt->byte, ret);
++ return ret;
++}
++
++static inline u8 read_rxram_slot_u8(struct bcm_qspi *qspi, int slot)
++{
++ u32 slot_offset = MSPI_RXRAM + (slot << 3) + 0x4;
++
++ /* mask out reserved bits */
++ return bcm_qspi_read(qspi, MSPI, slot_offset) & 0xff;
++}
++
++static inline u16 read_rxram_slot_u16(struct bcm_qspi *qspi, int slot)
++{
++ u32 reg_offset = MSPI_RXRAM;
++ u32 lsb_offset = reg_offset + (slot << 3) + 0x4;
++ u32 msb_offset = reg_offset + (slot << 3);
++
++ return (bcm_qspi_read(qspi, MSPI, lsb_offset) & 0xff) |
++ ((bcm_qspi_read(qspi, MSPI, msb_offset) & 0xff) << 8);
++}
++
++static void read_from_hw(struct bcm_qspi *qspi, int slots)
++{
++ struct qspi_trans tp;
++ int slot;
++
++ if (slots > MSPI_NUM_CDRAM) {
++ /* should never happen */
++ dev_err(&qspi->pdev->dev, "%s: too many slots!\n", __func__);
++ return;
++ }
++
++ tp = qspi->trans_pos;
++
++ for (slot = 0; slot < slots; slot++) {
++ if (tp.trans->bits_per_word <= 8) {
++ u8 *buf = tp.trans->rx_buf;
++
++ if (buf)
++ buf[tp.byte] = read_rxram_slot_u8(qspi, slot);
++ dev_dbg(&qspi->pdev->dev, "RD %02x\n",
++ buf ? buf[tp.byte] : 0xff);
++ } else {
++ u16 *buf = tp.trans->rx_buf;
++
++ if (buf)
++ buf[tp.byte / 2] = read_rxram_slot_u16(qspi,
++ slot);
++ dev_dbg(&qspi->pdev->dev, "RD %04x\n",
++ buf ? buf[tp.byte] : 0xffff);
++ }
++
++ update_qspi_trans_byte_count(qspi, &tp,
++ TRANS_STATUS_BREAK_NONE);
++ }
++
++ qspi->trans_pos = tp;
++}
++
++static inline void write_txram_slot_u8(struct bcm_qspi *qspi, int slot,
++ u8 val)
++{
++ u32 reg_offset = MSPI_TXRAM + (slot << 3);
++
++ /* mask out reserved bits */
++ bcm_qspi_write(qspi, MSPI, reg_offset, val);
++}
++
++static inline void write_txram_slot_u16(struct bcm_qspi *qspi, int slot,
++ u16 val)
++{
++ u32 reg_offset = MSPI_TXRAM;
++ u32 msb_offset = reg_offset + (slot << 3);
++ u32 lsb_offset = reg_offset + (slot << 3) + 0x4;
++
++ bcm_qspi_write(qspi, MSPI, msb_offset, (val >> 8));
++ bcm_qspi_write(qspi, MSPI, lsb_offset, (val & 0xff));
++}
++
++static inline u32 read_cdram_slot(struct bcm_qspi *qspi, int slot)
++{
++ return bcm_qspi_read(qspi, MSPI, MSPI_CDRAM + (slot << 2));
++}
++
++static inline void write_cdram_slot(struct bcm_qspi *qspi, int slot, u32 val)
++{
++ bcm_qspi_write(qspi, MSPI, (MSPI_CDRAM + (slot << 2)), val);
++}
++
++/* Return number of slots written */
++static int write_to_hw(struct bcm_qspi *qspi, struct spi_device *spi)
++{
++ struct qspi_trans tp;
++ int slot = 0, tstatus = 0;
++ u32 mspi_cdram = 0;
++
++ tp = qspi->trans_pos;
++ bcm_qspi_update_parms(qspi, spi, tp.trans);
++
++ /* Run until end of transfer or reached the max data */
++ while (!tstatus && slot < MSPI_NUM_CDRAM) {
++ if (tp.trans->bits_per_word <= 8) {
++ const u8 *buf = tp.trans->tx_buf;
++ u8 val = buf ? buf[tp.byte] : 0xff;
++
++ write_txram_slot_u8(qspi, slot, val);
++ dev_dbg(&qspi->pdev->dev, "WR %02x\n", val);
++ } else {
++ const u16 *buf = tp.trans->tx_buf;
++ u16 val = buf ? buf[tp.byte / 2] : 0xffff;
++
++ write_txram_slot_u16(qspi, slot, val);
++ dev_dbg(&qspi->pdev->dev, "WR %04x\n", val);
++ }
++ mspi_cdram = MSPI_CDRAM_CONT_BIT;
++ mspi_cdram |= (~(1 << spi->chip_select) &
++ MSPI_CDRAM_PCS);
++ mspi_cdram |= ((tp.trans->bits_per_word <= 8) ? 0 :
++ MSPI_CDRAM_BITSE_BIT);
++
++ write_cdram_slot(qspi, slot, mspi_cdram);
++
++ tstatus = update_qspi_trans_byte_count(qspi, &tp,
++ TRANS_STATUS_BREAK_TX);
++ slot++;
++ }
++
++ if (!slot) {
++ dev_err(&qspi->pdev->dev, "%s: no data to send?", __func__);
++ goto done;
++ }
++
++ dev_dbg(&qspi->pdev->dev, "submitting %d slots\n", slot);
++ bcm_qspi_write(qspi, MSPI, MSPI_NEWQP, 0);
++ bcm_qspi_write(qspi, MSPI, MSPI_ENDQP, slot - 1);
++
++ if (tstatus & TRANS_STATUS_BREAK_DESELECT) {
++ mspi_cdram = read_cdram_slot(qspi, slot - 1) &
++ ~MSPI_CDRAM_CONT_BIT;
++ write_cdram_slot(qspi, slot - 1, mspi_cdram);
++ }
++
++ /* Must flush previous writes before starting MSPI operation */
++ mb();
++ /* Set cont | spe | spifie */
++ bcm_qspi_write(qspi, MSPI, MSPI_SPCR2, 0xe0);
++
++done:
++ return slot;
++}
++
++static int bcm_qspi_transfer_one(struct spi_master *master,
++ struct spi_device *spi,
++ struct spi_transfer *trans)
++{
++ struct bcm_qspi *qspi = spi_master_get_devdata(master);
++ int slots;
++ unsigned long timeo = msecs_to_jiffies(100);
++
++ bcm_qspi_chip_select(qspi, spi->chip_select);
++ qspi->trans_pos.trans = trans;
++ qspi->trans_pos.byte = 0;
++
++ while (qspi->trans_pos.byte < trans->len) {
++ reinit_completion(&qspi->mspi_done);
++
++ slots = write_to_hw(qspi, spi);
++ if (!wait_for_completion_timeout(&qspi->mspi_done, timeo)) {
++ dev_err(&qspi->pdev->dev, "timeout waiting for MSPI\n");
++ return -ETIMEDOUT;
++ }
++
++ read_from_hw(qspi, slots);
++ }
++
++ return 0;
++}
++
++static void bcm_qspi_cleanup(struct spi_device *spi)
++{
++ struct bcm_qspi_parms *xp = spi_get_ctldata(spi);
++
++ kfree(xp);
++}
++
++static irqreturn_t bcm_qspi_mspi_l2_isr(int irq, void *dev_id)
++{
++ struct bcm_qspi_dev_id *qspi_dev_id = dev_id;
++ struct bcm_qspi *qspi = qspi_dev_id->dev;
++ u32 status = bcm_qspi_read(qspi, MSPI, MSPI_MSPI_STATUS);
++
++ if (status & MSPI_MSPI_STATUS_SPIF) {
++ /* clear interrupt */
++ status &= ~MSPI_MSPI_STATUS_SPIF;
++ bcm_qspi_write(qspi, MSPI, MSPI_MSPI_STATUS, status);
++ complete(&qspi->mspi_done);
++ return IRQ_HANDLED;
++ } else {
++ return IRQ_NONE;
++ }
++}
++
++static const struct bcm_qspi_irq qspi_irq_tab[] = {
++ {
++ .irq_name = "mspi_done",
++ .irq_handler = bcm_qspi_mspi_l2_isr,
++ .mask = INTR_MSPI_DONE_MASK,
++ },
++ {
++ .irq_name = "mspi_halted",
++ .irq_handler = bcm_qspi_mspi_l2_isr,
++ .mask = INTR_MSPI_HALTED_MASK,
++ },
++};
++
++static void bcm_qspi_hw_init(struct bcm_qspi *qspi)
++{
++ struct bcm_qspi_parms parms;
++
++ bcm_qspi_write(qspi, MSPI, MSPI_SPCR1_LSB, 0);
++ bcm_qspi_write(qspi, MSPI, MSPI_SPCR1_MSB, 0);
++ bcm_qspi_write(qspi, MSPI, MSPI_NEWQP, 0);
++ bcm_qspi_write(qspi, MSPI, MSPI_ENDQP, 0);
++ bcm_qspi_write(qspi, MSPI, MSPI_SPCR2, 0x20);
++
++ parms.mode = SPI_MODE_3;
++ parms.bits_per_word = 8;
++ parms.speed_hz = qspi->max_speed_hz;
++ bcm_qspi_hw_set_parms(qspi, &parms);
++}
++
++static void bcm_qspi_hw_uninit(struct bcm_qspi *qspi)
++{
++ bcm_qspi_write(qspi, MSPI, MSPI_SPCR2, 0);
++}
++
++static const struct of_device_id bcm_qspi_of_match[] = {
++ { .compatible = "brcm,spi-bcm-qspi" },
++ {},
++};
++MODULE_DEVICE_TABLE(of, bcm_qspi_of_match);
++
++int bcm_qspi_probe(struct platform_device *pdev,
++ struct bcm_qspi_soc_intc *soc)
++{
++ struct device *dev = &pdev->dev;
++ struct bcm_qspi *qspi;
++ struct spi_master *master;
++ struct resource *res;
++ int irq, ret = 0, num_ints = 0;
++ u32 val;
++ const char *name = NULL;
++ int num_irqs = ARRAY_SIZE(qspi_irq_tab);
++
++ /* We only support device-tree instantiation */
++ if (!dev->of_node)
++ return -ENODEV;
++
++ if (!of_match_node(bcm_qspi_of_match, dev->of_node))
++ return -ENODEV;
++
++ master = spi_alloc_master(dev, sizeof(struct bcm_qspi));
++ if (!master) {
++ dev_err(dev, "error allocating spi_master\n");
++ return -ENOMEM;
++ }
++
++ qspi = spi_master_get_devdata(master);
++ qspi->pdev = pdev;
++ qspi->trans_pos.trans = NULL;
++ qspi->trans_pos.byte = 0;
++ qspi->master = master;
++
++ master->bus_num = -1;
++ master->mode_bits = SPI_CPHA | SPI_CPOL | SPI_RX_DUAL | SPI_RX_QUAD;
++ master->setup = bcm_qspi_setup;
++ master->transfer_one = bcm_qspi_transfer_one;
++ master->cleanup = bcm_qspi_cleanup;
++ master->dev.of_node = dev->of_node;
++ master->num_chipselect = NUM_CHIPSELECT;
++
++ qspi->big_endian = of_device_is_big_endian(dev->of_node);
++
++ if (!of_property_read_u32(dev->of_node, "num-cs", &val))
++ master->num_chipselect = val;
++
++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "hif_mspi");
++ if (!res)
++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
++ "mspi");
++
++ if (res) {
++ qspi->base[MSPI] = devm_ioremap_resource(dev, res);
++ if (IS_ERR(qspi->base[MSPI])) {
++ ret = PTR_ERR(qspi->base[MSPI]);
++ goto qspi_probe_err;
++ }
++ } else {
++ goto qspi_probe_err;
++ }
++
++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "cs_reg");
++ if (res) {
++ qspi->base[CHIP_SELECT] = devm_ioremap_resource(dev, res);
++ if (IS_ERR(qspi->base[CHIP_SELECT])) {
++ ret = PTR_ERR(qspi->base[CHIP_SELECT]);
++ goto qspi_probe_err;
++ }
++ }
++
++ qspi->dev_ids = kcalloc(num_irqs, sizeof(struct bcm_qspi_dev_id),
++ GFP_KERNEL);
++ if (IS_ERR(qspi->dev_ids)) {
++ ret = PTR_ERR(qspi->dev_ids);
++ goto qspi_probe_err;
++ }
++
++ for (val = 0; val < num_irqs; val++) {
++ irq = -1;
++ name = qspi_irq_tab[val].irq_name;
++ irq = platform_get_irq_byname(pdev, name);
++
++ if (irq >= 0) {
++ ret = devm_request_irq(&pdev->dev, irq,
++ qspi_irq_tab[val].irq_handler, 0,
++ name,
++ &qspi->dev_ids[val]);
++ if (ret < 0) {
++ dev_err(&pdev->dev, "IRQ %s not found\n", name);
++ goto qspi_probe_err;
++ }
++
++ qspi->dev_ids[val].dev = qspi;
++ qspi->dev_ids[val].irqp = &qspi_irq_tab[val];
++ num_ints++;
++ dev_dbg(&pdev->dev, "registered IRQ %s %d\n",
++ qspi_irq_tab[val].irq_name,
++ irq);
++ }
++ }
++
++ if (!num_ints) {
++ dev_err(&pdev->dev, "no IRQs registered, cannot init driver\n");
++ goto qspi_probe_err;
++ }
++
++ qspi->clk = devm_clk_get(&pdev->dev, NULL);
++ if (IS_ERR(qspi->clk)) {
++ dev_warn(dev, "unable to get clock\n");
++ goto qspi_probe_err;
++ }
++
++ ret = clk_prepare_enable(qspi->clk);
++ if (ret) {
++ dev_err(dev, "failed to prepare clock\n");
++ goto qspi_probe_err;
++ }
++
++ qspi->base_clk = clk_get_rate(qspi->clk);
++ qspi->max_speed_hz = qspi->base_clk / (QSPI_SPBR_MIN * 2);
++
++ bcm_qspi_hw_init(qspi);
++ init_completion(&qspi->mspi_done);
++ qspi->curr_cs = -1;
++
++ platform_set_drvdata(pdev, qspi);
++ ret = devm_spi_register_master(&pdev->dev, master);
++ if (ret < 0) {
++ dev_err(dev, "can't register master\n");
++ goto qspi_reg_err;
++ }
++
++ return 0;
++
++qspi_reg_err:
++ bcm_qspi_hw_uninit(qspi);
++ clk_disable_unprepare(qspi->clk);
++qspi_probe_err:
++ spi_master_put(master);
++ kfree(qspi->dev_ids);
++ return ret;
++}
++/* probe function to be called by SoC specific platform driver probe */
++EXPORT_SYMBOL_GPL(bcm_qspi_probe);
++
++int bcm_qspi_remove(struct platform_device *pdev)
++{
++ struct bcm_qspi *qspi = platform_get_drvdata(pdev);
++
++ platform_set_drvdata(pdev, NULL);
++ bcm_qspi_hw_uninit(qspi);
++ clk_disable_unprepare(qspi->clk);
++ kfree(qspi->dev_ids);
++ spi_unregister_master(qspi->master);
++
++ return 0;
++}
++/* function to be called by SoC specific platform driver remove() */
++EXPORT_SYMBOL_GPL(bcm_qspi_remove);
++
++#ifdef CONFIG_PM_SLEEP
++static int bcm_qspi_suspend(struct device *dev)
++{
++ struct bcm_qspi *qspi = dev_get_drvdata(dev);
++
++ spi_master_suspend(qspi->master);
++ clk_disable(qspi->clk);
++ bcm_qspi_hw_uninit(qspi);
++
++ return 0;
++};
++
++static int bcm_qspi_resume(struct device *dev)
++{
++ struct bcm_qspi *qspi = dev_get_drvdata(dev);
++ int ret = 0;
++
++ bcm_qspi_hw_init(qspi);
++ bcm_qspi_chip_select(qspi, qspi->curr_cs);
++ ret = clk_enable(qspi->clk);
++ if (!ret)
++ spi_master_resume(qspi->master);
++
++ return ret;
++}
++#endif /* CONFIG_PM_SLEEP */
++
++const struct dev_pm_ops bcm_qspi_pm_ops = {
++ .suspend = bcm_qspi_suspend,
++ .resume = bcm_qspi_resume,
++};
++/* pm_ops to be called by SoC specific platform driver */
++EXPORT_SYMBOL_GPL(bcm_qspi_pm_ops);
++
++MODULE_AUTHOR("Kamal Dasu");
++MODULE_DESCRIPTION("Broadcom QSPI driver");
++MODULE_LICENSE("GPL v2");
++MODULE_ALIAS("platform:" DRIVER_NAME);
+--- /dev/null
++++ b/drivers/spi/spi-bcm-qspi.h
+@@ -0,0 +1,63 @@
++/*
++ * Copyright 2016 Broadcom
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License, version 2, as
++ * published by the Free Software Foundation (the "GPL").
++ *
++ * This program is distributed in the hope that it will be useful, but
++ * WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
++ * General Public License version 2 (GPLv2) for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * version 2 (GPLv2) along with this source code.
++ */
++
++#ifndef __SPI_BCM_QSPI_H__
++#define __SPI_BCM_QSPI_H__
++
++#include <linux/types.h>
++#include <linux/io.h>
++
++/* MSPI Interrupt masks */
++#define INTR_MSPI_HALTED_MASK BIT(6)
++#define INTR_MSPI_DONE_MASK BIT(5)
++
++#define MSPI_INTERRUPTS_ALL \
++ (INTR_MSPI_DONE_MASK | \
++ INTR_MSPI_HALTED_MASK)
++
++struct platform_device;
++struct dev_pm_ops;
++
++struct bcm_qspi_soc_intc;
++
++/* Read controller register*/
++static inline u32 bcm_qspi_readl(bool be, void __iomem *addr)
++{
++ if (be)
++ return ioread32be(addr);
++ else
++ return readl_relaxed(addr);
++}
++
++/* Write controller register*/
++static inline void bcm_qspi_writel(bool be,
++ unsigned int data, void __iomem *addr)
++{
++ if (be)
++ iowrite32be(data, addr);
++ else
++ writel_relaxed(data, addr);
++}
++
++/* The common driver functions to be called by the SoC platform driver */
++int bcm_qspi_probe(struct platform_device *pdev,
++ struct bcm_qspi_soc_intc *soc_intc);
++int bcm_qspi_remove(struct platform_device *pdev);
++
++/* pm_ops used by the SoC platform driver called on PM suspend/resume */
++extern const struct dev_pm_ops bcm_qspi_pm_ops;
++
++#endif /* __SPI_BCM_QSPI_H__ */
diff --git a/target/linux/bcm53xx/patches-4.4/083-0002-spi-brcmstb-qspi-Broadcom-settop-platform-driver.patch b/target/linux/bcm53xx/patches-4.4/083-0002-spi-brcmstb-qspi-Broadcom-settop-platform-driver.patch
new file mode 100644
index 0000000..476b11c
--- /dev/null
+++ b/target/linux/bcm53xx/patches-4.4/083-0002-spi-brcmstb-qspi-Broadcom-settop-platform-driver.patch
@@ -0,0 +1,84 @@
+From 44f95d87a6187f5027568bbcdce491713d7de5e5 Mon Sep 17 00:00:00 2001
+From: Kamal Dasu <kdasu.kdev at gmail.com>
+Date: Wed, 24 Aug 2016 18:04:24 -0400
+Subject: [PATCH] spi: brcmstb-qspi: Broadcom settop platform driver
+
+Adding the settop SoC platfrom driver, this driver is compatible
+with the settop MSPI+BSPI and MSPI only blocks implemented on the
+SoCs. Driver calls the spi-bcm-qspi probe(), remove() and pm_ops.
+
+Signed-off-by: Kamal Dasu <kdasu.kdev at gmail.com>
+Signed-off-by: Mark Brown <broonie at kernel.org>
+---
+ drivers/spi/Makefile | 2 +-
+ drivers/spi/spi-brcmstb-qspi.c | 53 ++++++++++++++++++++++++++++++++++++++++++
+ 2 files changed, 54 insertions(+), 1 deletion(-)
+ create mode 100644 drivers/spi/spi-brcmstb-qspi.c
+
+--- a/drivers/spi/Makefile
++++ b/drivers/spi/Makefile
+@@ -19,7 +19,7 @@ obj-$(CONFIG_SPI_BCM2835AUX) += spi-bcm
+ obj-$(CONFIG_SPI_BCM53XX) += spi-bcm53xx.o
+ obj-$(CONFIG_SPI_BCM63XX) += spi-bcm63xx.o
+ obj-$(CONFIG_SPI_BCM63XX_HSSPI) += spi-bcm63xx-hsspi.o
+-obj-$(CONFIG_SPI_BCM_QSPI) += spi-bcm-qspi.o
++obj-$(CONFIG_SPI_BCM_QSPI) += spi-brcmstb-qspi.o spi-bcm-qspi.o
+ obj-$(CONFIG_SPI_BFIN5XX) += spi-bfin5xx.o
+ obj-$(CONFIG_SPI_ADI_V3) += spi-adi-v3.o
+ obj-$(CONFIG_SPI_BFIN_SPORT) += spi-bfin-sport.o
+--- /dev/null
++++ b/drivers/spi/spi-brcmstb-qspi.c
+@@ -0,0 +1,53 @@
++/*
++ * Copyright 2016 Broadcom
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License, version 2, as
++ * published by the Free Software Foundation (the "GPL").
++ *
++ * This program is distributed in the hope that it will be useful, but
++ * WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
++ * General Public License version 2 (GPLv2) for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * version 2 (GPLv2) along with this source code.
++ */
++
++#include <linux/device.h>
++#include <linux/module.h>
++#include <linux/platform_device.h>
++#include <linux/of.h>
++#include "spi-bcm-qspi.h"
++
++static const struct of_device_id brcmstb_qspi_of_match[] = {
++ { .compatible = "brcm,spi-brcmstb-qspi" },
++ { .compatible = "brcm,spi-brcmstb-mspi" },
++ {},
++};
++MODULE_DEVICE_TABLE(of, brcmstb_qspi_of_match);
++
++static int brcmstb_qspi_probe(struct platform_device *pdev)
++{
++ return bcm_qspi_probe(pdev, NULL);
++}
++
++static int brcmstb_qspi_remove(struct platform_device *pdev)
++{
++ return bcm_qspi_remove(pdev);
++}
++
++static struct platform_driver brcmstb_qspi_driver = {
++ .probe = brcmstb_qspi_probe,
++ .remove = brcmstb_qspi_remove,
++ .driver = {
++ .name = "brcmstb_qspi",
++ .pm = &bcm_qspi_pm_ops,
++ .of_match_table = brcmstb_qspi_of_match,
++ }
++};
++module_platform_driver(brcmstb_qspi_driver);
++
++MODULE_LICENSE("GPL v2");
++MODULE_AUTHOR("Kamal Dasu");
++MODULE_DESCRIPTION("Broadcom SPI driver for settop SoC");
diff --git a/target/linux/bcm53xx/patches-4.4/083-0003-spi-bcm-qspi-Add-BSPI-spi-nor-flash-controller-drive.patch b/target/linux/bcm53xx/patches-4.4/083-0003-spi-bcm-qspi-Add-BSPI-spi-nor-flash-controller-drive.patch
new file mode 100644
index 0000000..f5f2ba0
--- /dev/null
+++ b/target/linux/bcm53xx/patches-4.4/083-0003-spi-bcm-qspi-Add-BSPI-spi-nor-flash-controller-drive.patch
@@ -0,0 +1,780 @@
+From 4e3b2d236fe00f0e0b6c45dcb3cc7d84c2316424 Mon Sep 17 00:00:00 2001
+From: Kamal Dasu <kdasu.kdev at gmail.com>
+Date: Wed, 24 Aug 2016 18:04:25 -0400
+Subject: [PATCH] spi: bcm-qspi: Add BSPI spi-nor flash controller driver
+
+This change implements BSPI driver for Broadcom BRCMSTB, NS2,
+NSP SoCs works in combination with the MSPI controller driver
+and implements flash read acceleration and implements the
+spi_flash_read() method. Both MSPI and BSPI controllers are
+needed to access spi-nor flash.
+
+Signed-off-by: Kamal Dasu <kdasu.kdev at gmail.com>
+Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy at broadcom.com>
+Signed-off-by: Mark Brown <broonie at kernel.org>
+---
+ drivers/spi/spi-bcm-qspi.c | 603 ++++++++++++++++++++++++++++++++++++++++++++-
+ drivers/spi/spi-bcm-qspi.h | 20 ++
+ 2 files changed, 620 insertions(+), 3 deletions(-)
+
+--- a/drivers/spi/spi-bcm-qspi.c
++++ b/drivers/spi/spi-bcm-qspi.c
+@@ -38,6 +38,60 @@
+
+ #define DRIVER_NAME "bcm_qspi"
+
++
++/* BSPI register offsets */
++#define BSPI_REVISION_ID 0x000
++#define BSPI_SCRATCH 0x004
++#define BSPI_MAST_N_BOOT_CTRL 0x008
++#define BSPI_BUSY_STATUS 0x00c
++#define BSPI_INTR_STATUS 0x010
++#define BSPI_B0_STATUS 0x014
++#define BSPI_B0_CTRL 0x018
++#define BSPI_B1_STATUS 0x01c
++#define BSPI_B1_CTRL 0x020
++#define BSPI_STRAP_OVERRIDE_CTRL 0x024
++#define BSPI_FLEX_MODE_ENABLE 0x028
++#define BSPI_BITS_PER_CYCLE 0x02c
++#define BSPI_BITS_PER_PHASE 0x030
++#define BSPI_CMD_AND_MODE_BYTE 0x034
++#define BSPI_BSPI_FLASH_UPPER_ADDR_BYTE 0x038
++#define BSPI_BSPI_XOR_VALUE 0x03c
++#define BSPI_BSPI_XOR_ENABLE 0x040
++#define BSPI_BSPI_PIO_MODE_ENABLE 0x044
++#define BSPI_BSPI_PIO_IODIR 0x048
++#define BSPI_BSPI_PIO_DATA 0x04c
++
++/* RAF register offsets */
++#define BSPI_RAF_START_ADDR 0x100
++#define BSPI_RAF_NUM_WORDS 0x104
++#define BSPI_RAF_CTRL 0x108
++#define BSPI_RAF_FULLNESS 0x10c
++#define BSPI_RAF_WATERMARK 0x110
++#define BSPI_RAF_STATUS 0x114
++#define BSPI_RAF_READ_DATA 0x118
++#define BSPI_RAF_WORD_CNT 0x11c
++#define BSPI_RAF_CURR_ADDR 0x120
++
++/* Override mode masks */
++#define BSPI_STRAP_OVERRIDE_CTRL_OVERRIDE BIT(0)
++#define BSPI_STRAP_OVERRIDE_CTRL_DATA_DUAL BIT(1)
++#define BSPI_STRAP_OVERRIDE_CTRL_ADDR_4BYTE BIT(2)
++#define BSPI_STRAP_OVERRIDE_CTRL_DATA_QUAD BIT(3)
++#define BSPI_STRAP_OVERRIDE_CTRL_ENDAIN_MODE BIT(4)
++
++#define BSPI_ADDRLEN_3BYTES 3
++#define BSPI_ADDRLEN_4BYTES 4
++
++#define BSPI_RAF_STATUS_FIFO_EMPTY_MASK BIT(1)
++
++#define BSPI_RAF_CTRL_START_MASK BIT(0)
++#define BSPI_RAF_CTRL_CLEAR_MASK BIT(1)
++
++#define BSPI_BPP_MODE_SELECT_MASK BIT(8)
++#define BSPI_BPP_ADDR_SELECT_MASK BIT(16)
++
++#define BSPI_READ_LENGTH 256
++
+ /* MSPI register offsets */
+ #define MSPI_SPCR0_LSB 0x000
+ #define MSPI_SPCR0_MSB 0x004
+@@ -108,8 +162,16 @@ struct bcm_qspi_parms {
+ u8 bits_per_word;
+ };
+
++struct bcm_xfer_mode {
++ bool flex_mode;
++ unsigned int width;
++ unsigned int addrlen;
++ unsigned int hp;
++};
++
+ enum base_type {
+ MSPI,
++ BSPI,
+ CHIP_SELECT,
+ BASEMAX,
+ };
+@@ -140,13 +202,28 @@ struct bcm_qspi {
+ struct bcm_qspi_parms last_parms;
+ struct qspi_trans trans_pos;
+ int curr_cs;
++ int bspi_maj_rev;
++ int bspi_min_rev;
++ int bspi_enabled;
++ struct spi_flash_read_message *bspi_rf_msg;
++ u32 bspi_rf_msg_idx;
++ u32 bspi_rf_msg_len;
++ u32 bspi_rf_msg_status;
++ struct bcm_xfer_mode xfer_mode;
+ u32 s3_strap_override_ctrl;
++ bool bspi_mode;
+ bool big_endian;
+ int num_irqs;
+ struct bcm_qspi_dev_id *dev_ids;
+ struct completion mspi_done;
++ struct completion bspi_done;
+ };
+
++static inline bool has_bspi(struct bcm_qspi *qspi)
++{
++ return qspi->bspi_mode;
++}
++
+ /* Read qspi controller register*/
+ static inline u32 bcm_qspi_read(struct bcm_qspi *qspi, enum base_type type,
+ unsigned int offset)
+@@ -161,6 +238,300 @@ static inline void bcm_qspi_write(struct
+ bcm_qspi_writel(qspi->big_endian, data, qspi->base[type] + offset);
+ }
+
++/* BSPI helpers */
++static int bcm_qspi_bspi_busy_poll(struct bcm_qspi *qspi)
++{
++ int i;
++
++ /* this should normally finish within 10us */
++ for (i = 0; i < 1000; i++) {
++ if (!(bcm_qspi_read(qspi, BSPI, BSPI_BUSY_STATUS) & 1))
++ return 0;
++ udelay(1);
++ }
++ dev_warn(&qspi->pdev->dev, "timeout waiting for !busy_status\n");
++ return -EIO;
++}
++
++static inline bool bcm_qspi_bspi_ver_three(struct bcm_qspi *qspi)
++{
++ if (qspi->bspi_maj_rev < 4)
++ return true;
++ return false;
++}
++
++static void bcm_qspi_bspi_flush_prefetch_buffers(struct bcm_qspi *qspi)
++{
++ bcm_qspi_bspi_busy_poll(qspi);
++ /* Force rising edge for the b0/b1 'flush' field */
++ bcm_qspi_write(qspi, BSPI, BSPI_B0_CTRL, 1);
++ bcm_qspi_write(qspi, BSPI, BSPI_B1_CTRL, 1);
++ bcm_qspi_write(qspi, BSPI, BSPI_B0_CTRL, 0);
++ bcm_qspi_write(qspi, BSPI, BSPI_B1_CTRL, 0);
++}
++
++static int bcm_qspi_bspi_lr_is_fifo_empty(struct bcm_qspi *qspi)
++{
++ return (bcm_qspi_read(qspi, BSPI, BSPI_RAF_STATUS) &
++ BSPI_RAF_STATUS_FIFO_EMPTY_MASK);
++}
++
++static inline u32 bcm_qspi_bspi_lr_read_fifo(struct bcm_qspi *qspi)
++{
++ u32 data = bcm_qspi_read(qspi, BSPI, BSPI_RAF_READ_DATA);
++
++ /* BSPI v3 LR is LE only, convert data to host endianness */
++ if (bcm_qspi_bspi_ver_three(qspi))
++ data = le32_to_cpu(data);
++
++ return data;
++}
++
++static inline void bcm_qspi_bspi_lr_start(struct bcm_qspi *qspi)
++{
++ bcm_qspi_bspi_busy_poll(qspi);
++ bcm_qspi_write(qspi, BSPI, BSPI_RAF_CTRL,
++ BSPI_RAF_CTRL_START_MASK);
++}
++
++static inline void bcm_qspi_bspi_lr_clear(struct bcm_qspi *qspi)
++{
++ bcm_qspi_write(qspi, BSPI, BSPI_RAF_CTRL,
++ BSPI_RAF_CTRL_CLEAR_MASK);
++ bcm_qspi_bspi_flush_prefetch_buffers(qspi);
++}
++
++static void bcm_qspi_bspi_lr_data_read(struct bcm_qspi *qspi)
++{
++ u32 *buf = (u32 *)qspi->bspi_rf_msg->buf;
++ u32 data = 0;
++
++ dev_dbg(&qspi->pdev->dev, "xfer %p rx %p rxlen %d\n", qspi->bspi_rf_msg,
++ qspi->bspi_rf_msg->buf, qspi->bspi_rf_msg_len);
++ while (!bcm_qspi_bspi_lr_is_fifo_empty(qspi)) {
++ data = bcm_qspi_bspi_lr_read_fifo(qspi);
++ if (likely(qspi->bspi_rf_msg_len >= 4) &&
++ IS_ALIGNED((uintptr_t)buf, 4)) {
++ buf[qspi->bspi_rf_msg_idx++] = data;
++ qspi->bspi_rf_msg_len -= 4;
++ } else {
++ /* Read out remaining bytes, make sure*/
++ u8 *cbuf = (u8 *)&buf[qspi->bspi_rf_msg_idx];
++
++ data = cpu_to_le32(data);
++ while (qspi->bspi_rf_msg_len) {
++ *cbuf++ = (u8)data;
++ data >>= 8;
++ qspi->bspi_rf_msg_len--;
++ }
++ }
++ }
++}
++
++static void bcm_qspi_bspi_set_xfer_params(struct bcm_qspi *qspi, u8 cmd_byte,
++ int bpp, int bpc, int flex_mode)
++{
++ bcm_qspi_write(qspi, BSPI, BSPI_FLEX_MODE_ENABLE, 0);
++ bcm_qspi_write(qspi, BSPI, BSPI_BITS_PER_CYCLE, bpc);
++ bcm_qspi_write(qspi, BSPI, BSPI_BITS_PER_PHASE, bpp);
++ bcm_qspi_write(qspi, BSPI, BSPI_CMD_AND_MODE_BYTE, cmd_byte);
++ bcm_qspi_write(qspi, BSPI, BSPI_FLEX_MODE_ENABLE, flex_mode);
++}
++
++static int bcm_qspi_bspi_set_flex_mode(struct bcm_qspi *qspi, int width,
++ int addrlen, int hp)
++{
++ int bpc = 0, bpp = 0;
++ u8 command = SPINOR_OP_READ_FAST;
++ int flex_mode = 1, rv = 0;
++ bool spans_4byte = false;
++
++ dev_dbg(&qspi->pdev->dev, "set flex mode w %x addrlen %x hp %d\n",
++ width, addrlen, hp);
++
++ if (addrlen == BSPI_ADDRLEN_4BYTES) {
++ bpp = BSPI_BPP_ADDR_SELECT_MASK;
++ spans_4byte = true;
++ }
++
++ bpp |= 8;
++
++ switch (width) {
++ case SPI_NBITS_SINGLE:
++ if (addrlen == BSPI_ADDRLEN_3BYTES)
++ /* default mode, does not need flex_cmd */
++ flex_mode = 0;
++ else
++ command = SPINOR_OP_READ4_FAST;
++ break;
++ case SPI_NBITS_DUAL:
++ bpc = 0x00000001;
++ if (hp) {
++ bpc |= 0x00010100; /* address and mode are 2-bit */
++ bpp = BSPI_BPP_MODE_SELECT_MASK;
++ command = OPCODE_DIOR;
++ if (spans_4byte)
++ command = OPCODE_DIOR_4B;
++ } else {
++ command = SPINOR_OP_READ_1_1_2;
++ if (spans_4byte)
++ command = SPINOR_OP_READ4_1_1_2;
++ }
++ break;
++ case SPI_NBITS_QUAD:
++ bpc = 0x00000002;
++ if (hp) {
++ bpc |= 0x00020200; /* address and mode are 4-bit */
++ bpp = 4; /* dummy cycles */
++ bpp |= BSPI_BPP_ADDR_SELECT_MASK;
++ command = OPCODE_QIOR;
++ if (spans_4byte)
++ command = OPCODE_QIOR_4B;
++ } else {
++ command = SPINOR_OP_READ_1_1_4;
++ if (spans_4byte)
++ command = SPINOR_OP_READ4_1_1_4;
++ }
++ break;
++ default:
++ rv = -EINVAL;
++ break;
++ }
++
++ if (rv == 0)
++ bcm_qspi_bspi_set_xfer_params(qspi, command, bpp, bpc,
++ flex_mode);
++
++ return rv;
++}
++
++static int bcm_qspi_bspi_set_override(struct bcm_qspi *qspi, int width,
++ int addrlen, int hp)
++{
++ u32 data = bcm_qspi_read(qspi, BSPI, BSPI_STRAP_OVERRIDE_CTRL);
++
++ dev_dbg(&qspi->pdev->dev, "set override mode w %x addrlen %x hp %d\n",
++ width, addrlen, hp);
++
++ switch (width) {
++ case SPI_NBITS_SINGLE:
++ /* clear quad/dual mode */
++ data &= ~(BSPI_STRAP_OVERRIDE_CTRL_DATA_QUAD |
++ BSPI_STRAP_OVERRIDE_CTRL_DATA_DUAL);
++ break;
++
++ case SPI_NBITS_QUAD:
++ /* clear dual mode and set quad mode */
++ data &= ~BSPI_STRAP_OVERRIDE_CTRL_DATA_DUAL;
++ data |= BSPI_STRAP_OVERRIDE_CTRL_DATA_QUAD;
++ break;
++ case SPI_NBITS_DUAL:
++ /* clear quad mode set dual mode */
++ data &= ~BSPI_STRAP_OVERRIDE_CTRL_DATA_QUAD;
++ data |= BSPI_STRAP_OVERRIDE_CTRL_DATA_DUAL;
++ break;
++ default:
++ return -EINVAL;
++ }
++
++ if (addrlen == BSPI_ADDRLEN_4BYTES)
++ /* set 4byte mode*/
++ data |= BSPI_STRAP_OVERRIDE_CTRL_ADDR_4BYTE;
++ else
++ /* clear 4 byte mode */
++ data &= ~BSPI_STRAP_OVERRIDE_CTRL_ADDR_4BYTE;
++
++ /* set the override mode */
++ data |= BSPI_STRAP_OVERRIDE_CTRL_OVERRIDE;
++ bcm_qspi_write(qspi, BSPI, BSPI_STRAP_OVERRIDE_CTRL, data);
++ bcm_qspi_bspi_set_xfer_params(qspi, SPINOR_OP_READ_FAST, 0, 0, 0);
++
++ return 0;
++}
++
++static int bcm_qspi_bspi_set_mode(struct bcm_qspi *qspi,
++ int width, int addrlen, int hp)
++{
++ int error = 0;
++
++ /* default mode */
++ qspi->xfer_mode.flex_mode = true;
++
++ if (!bcm_qspi_bspi_ver_three(qspi)) {
++ u32 val, mask;
++
++ val = bcm_qspi_read(qspi, BSPI, BSPI_STRAP_OVERRIDE_CTRL);
++ mask = BSPI_STRAP_OVERRIDE_CTRL_OVERRIDE;
++ if (val & mask || qspi->s3_strap_override_ctrl & mask) {
++ qspi->xfer_mode.flex_mode = false;
++ bcm_qspi_write(qspi, BSPI, BSPI_FLEX_MODE_ENABLE,
++ 0);
++
++ if ((val | qspi->s3_strap_override_ctrl) &
++ BSPI_STRAP_OVERRIDE_CTRL_DATA_DUAL)
++ width = SPI_NBITS_DUAL;
++ else if ((val | qspi->s3_strap_override_ctrl) &
++ BSPI_STRAP_OVERRIDE_CTRL_DATA_QUAD)
++ width = SPI_NBITS_QUAD;
++
++ error = bcm_qspi_bspi_set_override(qspi, width, addrlen,
++ hp);
++ }
++ }
++
++ if (qspi->xfer_mode.flex_mode)
++ error = bcm_qspi_bspi_set_flex_mode(qspi, width, addrlen, hp);
++
++ if (error) {
++ dev_warn(&qspi->pdev->dev,
++ "INVALID COMBINATION: width=%d addrlen=%d hp=%d\n",
++ width, addrlen, hp);
++ } else if (qspi->xfer_mode.width != width ||
++ qspi->xfer_mode.addrlen != addrlen ||
++ qspi->xfer_mode.hp != hp) {
++ qspi->xfer_mode.width = width;
++ qspi->xfer_mode.addrlen = addrlen;
++ qspi->xfer_mode.hp = hp;
++ dev_dbg(&qspi->pdev->dev,
++ "cs:%d %d-lane output, %d-byte address%s\n",
++ qspi->curr_cs,
++ qspi->xfer_mode.width,
++ qspi->xfer_mode.addrlen,
++ qspi->xfer_mode.hp != -1 ? ", hp mode" : "");
++ }
++
++ return error;
++}
++
++static void bcm_qspi_enable_bspi(struct bcm_qspi *qspi)
++{
++ if (!has_bspi(qspi) || (qspi->bspi_enabled))
++ return;
++
++ qspi->bspi_enabled = 1;
++ if ((bcm_qspi_read(qspi, BSPI, BSPI_MAST_N_BOOT_CTRL) & 1) == 0)
++ return;
++
++ bcm_qspi_bspi_flush_prefetch_buffers(qspi);
++ udelay(1);
++ bcm_qspi_write(qspi, BSPI, BSPI_MAST_N_BOOT_CTRL, 0);
++ udelay(1);
++}
++
++static void bcm_qspi_disable_bspi(struct bcm_qspi *qspi)
++{
++ if (!has_bspi(qspi) || (!qspi->bspi_enabled))
++ return;
++
++ qspi->bspi_enabled = 0;
++ if ((bcm_qspi_read(qspi, BSPI, BSPI_MAST_N_BOOT_CTRL) & 1))
++ return;
++
++ bcm_qspi_bspi_busy_poll(qspi);
++ bcm_qspi_write(qspi, BSPI, BSPI_MAST_N_BOOT_CTRL, 1);
++ udelay(1);
++}
++
+ static void bcm_qspi_chip_select(struct bcm_qspi *qspi, int cs)
+ {
+ u32 data = 0;
+@@ -298,6 +669,8 @@ static void read_from_hw(struct bcm_qspi
+ struct qspi_trans tp;
+ int slot;
+
++ bcm_qspi_disable_bspi(qspi);
++
+ if (slots > MSPI_NUM_CDRAM) {
+ /* should never happen */
+ dev_err(&qspi->pdev->dev, "%s: too many slots!\n", __func__);
+@@ -368,6 +741,7 @@ static int write_to_hw(struct bcm_qspi *
+ int slot = 0, tstatus = 0;
+ u32 mspi_cdram = 0;
+
++ bcm_qspi_disable_bspi(qspi);
+ tp = qspi->trans_pos;
+ bcm_qspi_update_parms(qspi, spi, tp.trans);
+
+@@ -414,6 +788,9 @@ static int write_to_hw(struct bcm_qspi *
+ write_cdram_slot(qspi, slot - 1, mspi_cdram);
+ }
+
++ if (has_bspi(qspi))
++ bcm_qspi_write(qspi, MSPI, MSPI_WRITE_LOCK, 1);
++
+ /* Must flush previous writes before starting MSPI operation */
+ mb();
+ /* Set cont | spe | spifie */
+@@ -423,6 +800,118 @@ done:
+ return slot;
+ }
+
++static int bcm_qspi_bspi_flash_read(struct spi_device *spi,
++ struct spi_flash_read_message *msg)
++{
++ struct bcm_qspi *qspi = spi_master_get_devdata(spi->master);
++ u32 addr = 0, len, len_words;
++ int ret = 0;
++ unsigned long timeo = msecs_to_jiffies(100);
++
++ if (bcm_qspi_bspi_ver_three(qspi))
++ if (msg->addr_width == BSPI_ADDRLEN_4BYTES)
++ return -EIO;
++
++ bcm_qspi_chip_select(qspi, spi->chip_select);
++ bcm_qspi_write(qspi, MSPI, MSPI_WRITE_LOCK, 0);
++
++ /*
++ * when using flex mode mode we need to send
++ * the upper address byte to bspi
++ */
++ if (bcm_qspi_bspi_ver_three(qspi) == false) {
++ addr = msg->from & 0xff000000;
++ bcm_qspi_write(qspi, BSPI,
++ BSPI_BSPI_FLASH_UPPER_ADDR_BYTE, addr);
++ }
++
++ if (!qspi->xfer_mode.flex_mode)
++ addr = msg->from;
++ else
++ addr = msg->from & 0x00ffffff;
++
++ /* set BSPI RAF buffer max read length */
++ len = msg->len;
++ if (len > BSPI_READ_LENGTH)
++ len = BSPI_READ_LENGTH;
++
++ if (bcm_qspi_bspi_ver_three(qspi) == true)
++ addr = (addr + 0xc00000) & 0xffffff;
++
++ reinit_completion(&qspi->bspi_done);
++ bcm_qspi_enable_bspi(qspi);
++ len_words = (len + 3) >> 2;
++ qspi->bspi_rf_msg = msg;
++ qspi->bspi_rf_msg_status = 0;
++ qspi->bspi_rf_msg_idx = 0;
++ qspi->bspi_rf_msg_len = len;
++ dev_dbg(&qspi->pdev->dev, "bspi xfr addr 0x%x len 0x%x", addr, len);
++
++ bcm_qspi_write(qspi, BSPI, BSPI_RAF_START_ADDR, addr);
++ bcm_qspi_write(qspi, BSPI, BSPI_RAF_NUM_WORDS, len_words);
++ bcm_qspi_write(qspi, BSPI, BSPI_RAF_WATERMARK, 0);
++
++ /* Must flush previous writes before starting BSPI operation */
++ mb();
++
++ bcm_qspi_bspi_lr_start(qspi);
++ if (!wait_for_completion_timeout(&qspi->bspi_done, timeo)) {
++ dev_err(&qspi->pdev->dev, "timeout waiting for BSPI\n");
++ ret = -ETIMEDOUT;
++ } else {
++ /* set the return length for the caller */
++ msg->retlen = len;
++ }
++
++ return ret;
++}
++
++static int bcm_qspi_flash_read(struct spi_device *spi,
++ struct spi_flash_read_message *msg)
++{
++ struct bcm_qspi *qspi = spi_master_get_devdata(spi->master);
++ int ret = 0;
++ bool mspi_read = false;
++ u32 io_width, addrlen, addr, len;
++ u_char *buf;
++
++ buf = msg->buf;
++ addr = msg->from;
++ len = msg->len;
++
++ if (bcm_qspi_bspi_ver_three(qspi) == true) {
++ /*
++ * The address coming into this function is a raw flash offset.
++ * But for BSPI <= V3, we need to convert it to a remapped BSPI
++ * address. If it crosses a 4MB boundary, just revert back to
++ * using MSPI.
++ */
++ addr = (addr + 0xc00000) & 0xffffff;
++
++ if ((~ADDR_4MB_MASK & addr) ^
++ (~ADDR_4MB_MASK & (addr + len - 1)))
++ mspi_read = true;
++ }
++
++ /* non-aligned and very short transfers are handled by MSPI */
++ if (!IS_ALIGNED((uintptr_t)addr, 4) || !IS_ALIGNED((uintptr_t)buf, 4) ||
++ len < 4)
++ mspi_read = true;
++
++ if (mspi_read)
++ /* this will make the m25p80 read to fallback to mspi read */
++ return -EAGAIN;
++
++ io_width = msg->data_nbits ? msg->data_nbits : SPI_NBITS_SINGLE;
++ addrlen = msg->addr_width;
++ ret = bcm_qspi_bspi_set_mode(qspi, io_width, addrlen, -1);
++
++ if (!ret)
++ ret = bcm_qspi_bspi_flash_read(spi, msg);
++
++ return ret;
++}
++
+ static int bcm_qspi_transfer_one(struct spi_master *master,
+ struct spi_device *spi,
+ struct spi_transfer *trans)
+@@ -469,13 +958,76 @@ static irqreturn_t bcm_qspi_mspi_l2_isr(
+ bcm_qspi_write(qspi, MSPI, MSPI_MSPI_STATUS, status);
+ complete(&qspi->mspi_done);
+ return IRQ_HANDLED;
+- } else {
+- return IRQ_NONE;
+ }
++
++ return IRQ_NONE;
++}
++
++static irqreturn_t bcm_qspi_bspi_lr_l2_isr(int irq, void *dev_id)
++{
++ struct bcm_qspi_dev_id *qspi_dev_id = dev_id;
++ struct bcm_qspi *qspi = qspi_dev_id->dev;
++ u32 status;
++
++ if (qspi->bspi_enabled && qspi->bspi_rf_msg) {
++ bcm_qspi_bspi_lr_data_read(qspi);
++ if (qspi->bspi_rf_msg_len == 0) {
++ qspi->bspi_rf_msg = NULL;
++ if (qspi->bspi_rf_msg_status)
++ bcm_qspi_bspi_lr_clear(qspi);
++ else
++ bcm_qspi_bspi_flush_prefetch_buffers(qspi);
++ }
++ }
++
++ status = (qspi_dev_id->irqp->mask & INTR_BSPI_LR_SESSION_DONE_MASK);
++ if (qspi->bspi_enabled && status && qspi->bspi_rf_msg_len == 0)
++ complete(&qspi->bspi_done);
++
++ return IRQ_HANDLED;
++}
++
++static irqreturn_t bcm_qspi_bspi_lr_err_l2_isr(int irq, void *dev_id)
++{
++ struct bcm_qspi_dev_id *qspi_dev_id = dev_id;
++ struct bcm_qspi *qspi = qspi_dev_id->dev;
++
++ dev_err(&qspi->pdev->dev, "BSPI INT error\n");
++ qspi->bspi_rf_msg_status = -EIO;
++ complete(&qspi->bspi_done);
++ return IRQ_HANDLED;
+ }
+
+ static const struct bcm_qspi_irq qspi_irq_tab[] = {
+ {
++ .irq_name = "spi_lr_fullness_reached",
++ .irq_handler = bcm_qspi_bspi_lr_l2_isr,
++ .mask = INTR_BSPI_LR_FULLNESS_REACHED_MASK,
++ },
++ {
++ .irq_name = "spi_lr_session_aborted",
++ .irq_handler = bcm_qspi_bspi_lr_err_l2_isr,
++ .mask = INTR_BSPI_LR_SESSION_ABORTED_MASK,
++ },
++ {
++ .irq_name = "spi_lr_impatient",
++ .irq_handler = bcm_qspi_bspi_lr_err_l2_isr,
++ .mask = INTR_BSPI_LR_IMPATIENT_MASK,
++ },
++ {
++ .irq_name = "spi_lr_session_done",
++ .irq_handler = bcm_qspi_bspi_lr_l2_isr,
++ .mask = INTR_BSPI_LR_SESSION_DONE_MASK,
++ },
++#ifdef QSPI_INT_DEBUG
++ /* this interrupt is for debug purposes only, dont request irq */
++ {
++ .irq_name = "spi_lr_overread",
++ .irq_handler = bcm_qspi_bspi_lr_err_l2_isr,
++ .mask = INTR_BSPI_LR_OVERREAD_MASK,
++ },
++#endif
++ {
+ .irq_name = "mspi_done",
+ .irq_handler = bcm_qspi_mspi_l2_isr,
+ .mask = INTR_MSPI_DONE_MASK,
+@@ -487,6 +1039,24 @@ static const struct bcm_qspi_irq qspi_ir
+ },
+ };
+
++static void bcm_qspi_bspi_init(struct bcm_qspi *qspi)
++{
++ u32 val = 0;
++
++ val = bcm_qspi_read(qspi, BSPI, BSPI_REVISION_ID);
++ qspi->bspi_maj_rev = (val >> 8) & 0xff;
++ qspi->bspi_min_rev = val & 0xff;
++ if (!(bcm_qspi_bspi_ver_three(qspi))) {
++ /* Force mapping of BSPI address -> flash offset */
++ bcm_qspi_write(qspi, BSPI, BSPI_BSPI_XOR_VALUE, 0);
++ bcm_qspi_write(qspi, BSPI, BSPI_BSPI_XOR_ENABLE, 1);
++ }
++ qspi->bspi_enabled = 1;
++ bcm_qspi_disable_bspi(qspi);
++ bcm_qspi_write(qspi, BSPI, BSPI_B0_CTRL, 0);
++ bcm_qspi_write(qspi, BSPI, BSPI_B1_CTRL, 0);
++}
++
+ static void bcm_qspi_hw_init(struct bcm_qspi *qspi)
+ {
+ struct bcm_qspi_parms parms;
+@@ -501,11 +1071,17 @@ static void bcm_qspi_hw_init(struct bcm_
+ parms.bits_per_word = 8;
+ parms.speed_hz = qspi->max_speed_hz;
+ bcm_qspi_hw_set_parms(qspi, &parms);
++
++ if (has_bspi(qspi))
++ bcm_qspi_bspi_init(qspi);
+ }
+
+ static void bcm_qspi_hw_uninit(struct bcm_qspi *qspi)
+ {
+ bcm_qspi_write(qspi, MSPI, MSPI_SPCR2, 0);
++ if (has_bspi(qspi))
++ bcm_qspi_write(qspi, MSPI, MSPI_WRITE_LOCK, 0);
++
+ }
+
+ static const struct of_device_id bcm_qspi_of_match[] = {
+@@ -515,7 +1091,7 @@ static const struct of_device_id bcm_qsp
+ MODULE_DEVICE_TABLE(of, bcm_qspi_of_match);
+
+ int bcm_qspi_probe(struct platform_device *pdev,
+- struct bcm_qspi_soc_intc *soc)
++ struct bcm_qspi_soc_intc *soc_intc)
+ {
+ struct device *dev = &pdev->dev;
+ struct bcm_qspi *qspi;
+@@ -549,6 +1125,7 @@ int bcm_qspi_probe(struct platform_devic
+ master->mode_bits = SPI_CPHA | SPI_CPOL | SPI_RX_DUAL | SPI_RX_QUAD;
+ master->setup = bcm_qspi_setup;
+ master->transfer_one = bcm_qspi_transfer_one;
++ master->spi_flash_read = bcm_qspi_flash_read;
+ master->cleanup = bcm_qspi_cleanup;
+ master->dev.of_node = dev->of_node;
+ master->num_chipselect = NUM_CHIPSELECT;
+@@ -573,6 +1150,20 @@ int bcm_qspi_probe(struct platform_devic
+ goto qspi_probe_err;
+ }
+
++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "bspi");
++ if (res) {
++ qspi->base[BSPI] = devm_ioremap_resource(dev, res);
++ if (IS_ERR(qspi->base[BSPI])) {
++ ret = PTR_ERR(qspi->base[BSPI]);
++ goto qspi_probe_err;
++ }
++ qspi->bspi_mode = true;
++ } else {
++ qspi->bspi_mode = false;
++ }
++
++ dev_info(dev, "using %smspi mode\n", qspi->bspi_mode ? "bspi-" : "");
++
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "cs_reg");
+ if (res) {
+ qspi->base[CHIP_SELECT] = devm_ioremap_resource(dev, res);
+@@ -635,9 +1226,15 @@ int bcm_qspi_probe(struct platform_devic
+
+ bcm_qspi_hw_init(qspi);
+ init_completion(&qspi->mspi_done);
++ init_completion(&qspi->bspi_done);
+ qspi->curr_cs = -1;
+
+ platform_set_drvdata(pdev, qspi);
++
++ qspi->xfer_mode.width = -1;
++ qspi->xfer_mode.addrlen = -1;
++ qspi->xfer_mode.hp = -1;
++
+ ret = devm_spi_register_master(&pdev->dev, master);
+ if (ret < 0) {
+ dev_err(dev, "can't register master\n");
+--- a/drivers/spi/spi-bcm-qspi.h
++++ b/drivers/spi/spi-bcm-qspi.h
+@@ -20,6 +20,26 @@
+ #include <linux/types.h>
+ #include <linux/io.h>
+
++/* BSPI interrupt masks */
++#define INTR_BSPI_LR_OVERREAD_MASK BIT(4)
++#define INTR_BSPI_LR_SESSION_DONE_MASK BIT(3)
++#define INTR_BSPI_LR_IMPATIENT_MASK BIT(2)
++#define INTR_BSPI_LR_SESSION_ABORTED_MASK BIT(1)
++#define INTR_BSPI_LR_FULLNESS_REACHED_MASK BIT(0)
++
++#define BSPI_LR_INTERRUPTS_DATA \
++ (INTR_BSPI_LR_SESSION_DONE_MASK | \
++ INTR_BSPI_LR_FULLNESS_REACHED_MASK)
++
++#define BSPI_LR_INTERRUPTS_ERROR \
++ (INTR_BSPI_LR_OVERREAD_MASK | \
++ INTR_BSPI_LR_IMPATIENT_MASK | \
++ INTR_BSPI_LR_SESSION_ABORTED_MASK)
++
++#define BSPI_LR_INTERRUPTS_ALL \
++ (BSPI_LR_INTERRUPTS_ERROR | \
++ BSPI_LR_INTERRUPTS_DATA)
++
+ /* MSPI Interrupt masks */
+ #define INTR_MSPI_HALTED_MASK BIT(6)
+ #define INTR_MSPI_DONE_MASK BIT(5)
diff --git a/target/linux/bcm53xx/patches-4.4/083-0004-spi-bcm-qspi-don-t-include-linux-mtd-cfi.h.patch b/target/linux/bcm53xx/patches-4.4/083-0004-spi-bcm-qspi-don-t-include-linux-mtd-cfi.h.patch
new file mode 100644
index 0000000..f90c02b
--- /dev/null
+++ b/target/linux/bcm53xx/patches-4.4/083-0004-spi-bcm-qspi-don-t-include-linux-mtd-cfi.h.patch
@@ -0,0 +1,27 @@
+From c0a75d072a501effd66d3392ada8d3f4283b87ef Mon Sep 17 00:00:00 2001
+From: Arnd Bergmann <arnd at arndb.de>
+Date: Thu, 15 Sep 2016 17:40:15 +0200
+Subject: [PATCH] spi: bcm-qspi: don't include linux/mtd/cfi.h
+
+The header isn't actually needed here, but including it leads
+to a build warning when CONFIG_MTD is disabled:
+
+include/linux/mtd/cfi.h:76:2: #warning No CONFIG_MTD_CFI_Ix selected. No NOR chip support can work. [-Werror=cpp]
+
+Fixes: fa236a7ef240 (spi: bcm-qspi: Add Broadcom MSPI driver)
+Signed-off-by: Arnd Bergmann <arnd at arndb.de>
+Signed-off-by: Mark Brown <broonie at kernel.org>
+---
+ drivers/spi/spi-bcm-qspi.c | 1 -
+ 1 file changed, 1 deletion(-)
+
+--- a/drivers/spi/spi-bcm-qspi.c
++++ b/drivers/spi/spi-bcm-qspi.c
+@@ -25,7 +25,6 @@
+ #include <linux/ioport.h>
+ #include <linux/kernel.h>
+ #include <linux/module.h>
+-#include <linux/mtd/cfi.h>
+ #include <linux/mtd/spi-nor.h>
+ #include <linux/of.h>
+ #include <linux/of_irq.h>
diff --git a/target/linux/bcm53xx/patches-4.4/083-0005-spi-bcm-qspi-fix-suspend-resume-ifdef.patch b/target/linux/bcm53xx/patches-4.4/083-0005-spi-bcm-qspi-fix-suspend-resume-ifdef.patch
new file mode 100644
index 0000000..aad22d2
--- /dev/null
+++ b/target/linux/bcm53xx/patches-4.4/083-0005-spi-bcm-qspi-fix-suspend-resume-ifdef.patch
@@ -0,0 +1,63 @@
+From a0319f8b12c0fb9800da61f4cba9bd6fd80e37a4 Mon Sep 17 00:00:00 2001
+From: Arnd Bergmann <arnd at arndb.de>
+Date: Thu, 15 Sep 2016 17:46:53 +0200
+Subject: [PATCH] spi: bcm-qspi: fix suspend/resume #ifdef
+
+The two power management functions are define inside of an #ifdef
+but referenced unconditionally, which is obviously broken when
+CONFIG_PM_SLEEP is not set:
+
+drivers/spi/spi-bcm-qspi.c:1300:13: error: 'bcm_qspi_suspend' undeclared here (not in a function)
+drivers/spi/spi-bcm-qspi.c:1301:13: error: 'bcm_qspi_resume' undeclared here (not in a function)
+
+This replaces the #ifdef with a __maybe_unused annotation that lets
+the compiler figure out whether to drop the functions itself,
+and uses SIMPLE_DEV_PM_OPS() to refer to the functions.
+
+This will also fill the freeze/thaw/poweroff/restore callback
+pointers in addition to suspend/resume, but as far as I can tell,
+this is what we want.
+
+Signed-off-by: Arnd Bergmann <arnd at arndb.de>
+Fixes: fa236a7ef240 ("spi: bcm-qspi: Add Broadcom MSPI driver")
+Signed-off-by: Mark Brown <broonie at kernel.org>
+---
+ drivers/spi/spi-bcm-qspi.c | 12 ++++--------
+ 1 file changed, 4 insertions(+), 8 deletions(-)
+
+--- a/drivers/spi/spi-bcm-qspi.c
++++ b/drivers/spi/spi-bcm-qspi.c
+@@ -1268,8 +1268,7 @@ int bcm_qspi_remove(struct platform_devi
+ /* function to be called by SoC specific platform driver remove() */
+ EXPORT_SYMBOL_GPL(bcm_qspi_remove);
+
+-#ifdef CONFIG_PM_SLEEP
+-static int bcm_qspi_suspend(struct device *dev)
++static int __maybe_unused bcm_qspi_suspend(struct device *dev)
+ {
+ struct bcm_qspi *qspi = dev_get_drvdata(dev);
+
+@@ -1280,7 +1279,7 @@ static int bcm_qspi_suspend(struct devic
+ return 0;
+ };
+
+-static int bcm_qspi_resume(struct device *dev)
++static int __maybe_unused bcm_qspi_resume(struct device *dev)
+ {
+ struct bcm_qspi *qspi = dev_get_drvdata(dev);
+ int ret = 0;
+@@ -1293,12 +1292,9 @@ static int bcm_qspi_resume(struct device
+
+ return ret;
+ }
+-#endif /* CONFIG_PM_SLEEP */
+
+-const struct dev_pm_ops bcm_qspi_pm_ops = {
+- .suspend = bcm_qspi_suspend,
+- .resume = bcm_qspi_resume,
+-};
++SIMPLE_DEV_PM_OPS(bcm_qspi_pm_ops, bcm_qspi_suspend, bcm_qspi_resume);
++
+ /* pm_ops to be called by SoC specific platform driver */
+ EXPORT_SYMBOL_GPL(bcm_qspi_pm_ops);
+
diff --git a/target/linux/bcm53xx/patches-4.4/083-0006-spi-bcm-qspi-Fix-return-value-check-in-bcm_qspi_prob.patch b/target/linux/bcm53xx/patches-4.4/083-0006-spi-bcm-qspi-Fix-return-value-check-in-bcm_qspi_prob.patch
new file mode 100644
index 0000000..d71b2f4
--- /dev/null
+++ b/target/linux/bcm53xx/patches-4.4/083-0006-spi-bcm-qspi-Fix-return-value-check-in-bcm_qspi_prob.patch
@@ -0,0 +1,29 @@
+From 3bf3eb2b95aaf18eff3080444b24673cda8ff9a2 Mon Sep 17 00:00:00 2001
+From: Wei Yongjun <weiyongjun1 at huawei.com>
+Date: Fri, 16 Sep 2016 13:45:17 +0000
+Subject: [PATCH] spi: bcm-qspi: Fix return value check in bcm_qspi_probe()
+
+In case of error, the function kcalloc() returns NULL pointer
+not ERR_PTR(). The IS_ERR() test in the return value check
+should be replaced with NULL test.
+
+Fixes: fa236a7ef240 ("spi: bcm-qspi: Add Broadcom MSPI driver")
+Signed-off-by: Wei Yongjun <weiyongjun1 at huawei.com>
+Signed-off-by: Mark Brown <broonie at kernel.org>
+---
+ drivers/spi/spi-bcm-qspi.c | 4 ++--
+ 1 file changed, 2 insertions(+), 2 deletions(-)
+
+--- a/drivers/spi/spi-bcm-qspi.c
++++ b/drivers/spi/spi-bcm-qspi.c
+@@ -1174,8 +1174,8 @@ int bcm_qspi_probe(struct platform_devic
+
+ qspi->dev_ids = kcalloc(num_irqs, sizeof(struct bcm_qspi_dev_id),
+ GFP_KERNEL);
+- if (IS_ERR(qspi->dev_ids)) {
+- ret = PTR_ERR(qspi->dev_ids);
++ if (!qspi->dev_ids) {
++ ret = -ENOMEM;
+ goto qspi_probe_err;
+ }
+
diff --git a/target/linux/bcm53xx/patches-4.4/083-0007-spi-bcm-qspi-Fix-error-return-code-in-bcm_qspi_probe.patch b/target/linux/bcm53xx/patches-4.4/083-0007-spi-bcm-qspi-Fix-error-return-code-in-bcm_qspi_probe.patch
new file mode 100644
index 0000000..a15deb5
--- /dev/null
+++ b/target/linux/bcm53xx/patches-4.4/083-0007-spi-bcm-qspi-Fix-error-return-code-in-bcm_qspi_probe.patch
@@ -0,0 +1,32 @@
+From 71b8f350a4f03730f3024bfa7dc2414904a21bcb Mon Sep 17 00:00:00 2001
+From: Wei Yongjun <weiyongjun1 at huawei.com>
+Date: Fri, 16 Sep 2016 14:00:19 +0000
+Subject: [PATCH] spi: bcm-qspi: Fix error return code in bcm_qspi_probe()
+
+Fix to return a negative error code from the error handling
+case instead of 0, as done elsewhere in this function.
+
+Fixes: fa236a7ef240 ("spi: bcm-qspi: Add Broadcom MSPI driver")
+Signed-off-by: Wei Yongjun <weiyongjun1 at huawei.com>
+Signed-off-by: Mark Brown <broonie at kernel.org>
+---
+ drivers/spi/spi-bcm-qspi.c | 2 ++
+ 1 file changed, 2 insertions(+)
+
+--- a/drivers/spi/spi-bcm-qspi.c
++++ b/drivers/spi/spi-bcm-qspi.c
+@@ -1205,12 +1205,14 @@ int bcm_qspi_probe(struct platform_devic
+
+ if (!num_ints) {
+ dev_err(&pdev->dev, "no IRQs registered, cannot init driver\n");
++ ret = -EINVAL;
+ goto qspi_probe_err;
+ }
+
+ qspi->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(qspi->clk)) {
+ dev_warn(dev, "unable to get clock\n");
++ ret = PTR_ERR(qspi->clk);
+ goto qspi_probe_err;
+ }
+
diff --git a/target/linux/bcm53xx/patches-4.4/083-0008-spi-iproc-qspi-Add-Broadcom-iProc-SoCs-support.patch b/target/linux/bcm53xx/patches-4.4/083-0008-spi-iproc-qspi-Add-Broadcom-iProc-SoCs-support.patch
new file mode 100644
index 0000000..836d629
--- /dev/null
+++ b/target/linux/bcm53xx/patches-4.4/083-0008-spi-iproc-qspi-Add-Broadcom-iProc-SoCs-support.patch
@@ -0,0 +1,452 @@
+From cc20a38612dbc87dc7396affc9758e3bfbe92340 Mon Sep 17 00:00:00 2001
+From: Kamal Dasu <kdasu.kdev at gmail.com>
+Date: Wed, 24 Aug 2016 18:04:29 -0400
+Subject: [PATCH] spi: iproc-qspi: Add Broadcom iProc SoCs support
+
+This spi driver uses the common spi-bcm-qspi driver and implements iProc
+SoCs specific interrupt controller. The common driver now calls the SoC
+handlers when present. Adding support for both muxed l1 and unmuxed interrupt
+sources.
+
+Signed-off-by: Kamal Dasu <kdasu.kdev at gmail.com>
+Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy at broadcom.com>
+Signed-off-by: Mark Brown <broonie at kernel.org>
+---
+ drivers/spi/Makefile | 2 +-
+ drivers/spi/spi-bcm-qspi.c | 97 ++++++++++++++++++++++++-
+ drivers/spi/spi-bcm-qspi.h | 34 ++++++++-
+ drivers/spi/spi-iproc-qspi.c | 163 +++++++++++++++++++++++++++++++++++++++++++
+ 4 files changed, 291 insertions(+), 5 deletions(-)
+ create mode 100644 drivers/spi/spi-iproc-qspi.c
+
+--- a/drivers/spi/Makefile
++++ b/drivers/spi/Makefile
+@@ -19,7 +19,7 @@ obj-$(CONFIG_SPI_BCM2835AUX) += spi-bcm
+ obj-$(CONFIG_SPI_BCM53XX) += spi-bcm53xx.o
+ obj-$(CONFIG_SPI_BCM63XX) += spi-bcm63xx.o
+ obj-$(CONFIG_SPI_BCM63XX_HSSPI) += spi-bcm63xx-hsspi.o
+-obj-$(CONFIG_SPI_BCM_QSPI) += spi-brcmstb-qspi.o spi-bcm-qspi.o
++obj-$(CONFIG_SPI_BCM_QSPI) += spi-iproc-qspi.o spi-brcmstb-qspi.o spi-bcm-qspi.o
+ obj-$(CONFIG_SPI_BFIN5XX) += spi-bfin5xx.o
+ obj-$(CONFIG_SPI_ADI_V3) += spi-adi-v3.o
+ obj-$(CONFIG_SPI_BFIN_SPORT) += spi-bfin-sport.o
+--- a/drivers/spi/spi-bcm-qspi.c
++++ b/drivers/spi/spi-bcm-qspi.c
+@@ -175,9 +175,15 @@ enum base_type {
+ BASEMAX,
+ };
+
++enum irq_source {
++ SINGLE_L2,
++ MUXED_L1,
++};
++
+ struct bcm_qspi_irq {
+ const char *irq_name;
+ const irq_handler_t irq_handler;
++ int irq_source;
+ u32 mask;
+ };
+
+@@ -198,6 +204,10 @@ struct bcm_qspi {
+ u32 base_clk;
+ u32 max_speed_hz;
+ void __iomem *base[BASEMAX];
++
++ /* Some SoCs provide custom interrupt status register(s) */
++ struct bcm_qspi_soc_intc *soc_intc;
++
+ struct bcm_qspi_parms last_parms;
+ struct qspi_trans trans_pos;
+ int curr_cs;
+@@ -806,6 +816,7 @@ static int bcm_qspi_bspi_flash_read(stru
+ u32 addr = 0, len, len_words;
+ int ret = 0;
+ unsigned long timeo = msecs_to_jiffies(100);
++ struct bcm_qspi_soc_intc *soc_intc = qspi->soc_intc;
+
+ if (bcm_qspi_bspi_ver_three(qspi))
+ if (msg->addr_width == BSPI_ADDRLEN_4BYTES)
+@@ -850,6 +861,15 @@ static int bcm_qspi_bspi_flash_read(stru
+ bcm_qspi_write(qspi, BSPI, BSPI_RAF_NUM_WORDS, len_words);
+ bcm_qspi_write(qspi, BSPI, BSPI_RAF_WATERMARK, 0);
+
++ if (qspi->soc_intc) {
++ /*
++ * clear soc MSPI and BSPI interrupts and enable
++ * BSPI interrupts.
++ */
++ soc_intc->bcm_qspi_int_ack(soc_intc, MSPI_BSPI_DONE);
++ soc_intc->bcm_qspi_int_set(soc_intc, BSPI_DONE, true);
++ }
++
+ /* Must flush previous writes before starting BSPI operation */
+ mb();
+
+@@ -952,9 +972,12 @@ static irqreturn_t bcm_qspi_mspi_l2_isr(
+ u32 status = bcm_qspi_read(qspi, MSPI, MSPI_MSPI_STATUS);
+
+ if (status & MSPI_MSPI_STATUS_SPIF) {
++ struct bcm_qspi_soc_intc *soc_intc = qspi->soc_intc;
+ /* clear interrupt */
+ status &= ~MSPI_MSPI_STATUS_SPIF;
+ bcm_qspi_write(qspi, MSPI, MSPI_MSPI_STATUS, status);
++ if (qspi->soc_intc)
++ soc_intc->bcm_qspi_int_ack(soc_intc, MSPI_DONE);
+ complete(&qspi->mspi_done);
+ return IRQ_HANDLED;
+ }
+@@ -966,20 +989,33 @@ static irqreturn_t bcm_qspi_bspi_lr_l2_i
+ {
+ struct bcm_qspi_dev_id *qspi_dev_id = dev_id;
+ struct bcm_qspi *qspi = qspi_dev_id->dev;
+- u32 status;
++ struct bcm_qspi_soc_intc *soc_intc = qspi->soc_intc;
++ u32 status = qspi_dev_id->irqp->mask;
+
+ if (qspi->bspi_enabled && qspi->bspi_rf_msg) {
+ bcm_qspi_bspi_lr_data_read(qspi);
+ if (qspi->bspi_rf_msg_len == 0) {
+ qspi->bspi_rf_msg = NULL;
++ if (qspi->soc_intc) {
++ /* disable soc BSPI interrupt */
++ soc_intc->bcm_qspi_int_set(soc_intc, BSPI_DONE,
++ false);
++ /* indicate done */
++ status = INTR_BSPI_LR_SESSION_DONE_MASK;
++ }
++
+ if (qspi->bspi_rf_msg_status)
+ bcm_qspi_bspi_lr_clear(qspi);
+ else
+ bcm_qspi_bspi_flush_prefetch_buffers(qspi);
+ }
++
++ if (qspi->soc_intc)
++ /* clear soc BSPI interrupt */
++ soc_intc->bcm_qspi_int_ack(soc_intc, BSPI_DONE);
+ }
+
+- status = (qspi_dev_id->irqp->mask & INTR_BSPI_LR_SESSION_DONE_MASK);
++ status &= INTR_BSPI_LR_SESSION_DONE_MASK;
+ if (qspi->bspi_enabled && status && qspi->bspi_rf_msg_len == 0)
+ complete(&qspi->bspi_done);
+
+@@ -990,13 +1026,39 @@ static irqreturn_t bcm_qspi_bspi_lr_err_
+ {
+ struct bcm_qspi_dev_id *qspi_dev_id = dev_id;
+ struct bcm_qspi *qspi = qspi_dev_id->dev;
++ struct bcm_qspi_soc_intc *soc_intc = qspi->soc_intc;
+
+ dev_err(&qspi->pdev->dev, "BSPI INT error\n");
+ qspi->bspi_rf_msg_status = -EIO;
++ if (qspi->soc_intc)
++ /* clear soc interrupt */
++ soc_intc->bcm_qspi_int_ack(soc_intc, BSPI_ERR);
++
+ complete(&qspi->bspi_done);
+ return IRQ_HANDLED;
+ }
+
++static irqreturn_t bcm_qspi_l1_isr(int irq, void *dev_id)
++{
++ struct bcm_qspi_dev_id *qspi_dev_id = dev_id;
++ struct bcm_qspi *qspi = qspi_dev_id->dev;
++ struct bcm_qspi_soc_intc *soc_intc = qspi->soc_intc;
++ irqreturn_t ret = IRQ_NONE;
++
++ if (soc_intc) {
++ u32 status = soc_intc->bcm_qspi_get_int_status(soc_intc);
++
++ if (status & MSPI_DONE)
++ ret = bcm_qspi_mspi_l2_isr(irq, dev_id);
++ else if (status & BSPI_DONE)
++ ret = bcm_qspi_bspi_lr_l2_isr(irq, dev_id);
++ else if (status & BSPI_ERR)
++ ret = bcm_qspi_bspi_lr_err_l2_isr(irq, dev_id);
++ }
++
++ return ret;
++}
++
+ static const struct bcm_qspi_irq qspi_irq_tab[] = {
+ {
+ .irq_name = "spi_lr_fullness_reached",
+@@ -1036,6 +1098,13 @@ static const struct bcm_qspi_irq qspi_ir
+ .irq_handler = bcm_qspi_mspi_l2_isr,
+ .mask = INTR_MSPI_HALTED_MASK,
+ },
++ {
++ /* single muxed L1 interrupt source */
++ .irq_name = "spi_l1_intr",
++ .irq_handler = bcm_qspi_l1_isr,
++ .irq_source = MUXED_L1,
++ .mask = QSPI_INTERRUPTS_ALL,
++ },
+ };
+
+ static void bcm_qspi_bspi_init(struct bcm_qspi *qspi)
+@@ -1182,7 +1251,13 @@ int bcm_qspi_probe(struct platform_devic
+ for (val = 0; val < num_irqs; val++) {
+ irq = -1;
+ name = qspi_irq_tab[val].irq_name;
+- irq = platform_get_irq_byname(pdev, name);
++ if (qspi_irq_tab[val].irq_source == SINGLE_L2) {
++ /* get the l2 interrupts */
++ irq = platform_get_irq_byname(pdev, name);
++ } else if (!num_ints && soc_intc) {
++ /* all mspi, bspi intrs muxed to one L1 intr */
++ irq = platform_get_irq(pdev, 0);
++ }
+
+ if (irq >= 0) {
+ ret = devm_request_irq(&pdev->dev, irq,
+@@ -1209,6 +1284,17 @@ int bcm_qspi_probe(struct platform_devic
+ goto qspi_probe_err;
+ }
+
++ /*
++ * Some SoCs integrate spi controller (e.g., its interrupt bits)
++ * in specific ways
++ */
++ if (soc_intc) {
++ qspi->soc_intc = soc_intc;
++ soc_intc->bcm_qspi_int_set(soc_intc, MSPI_DONE, true);
++ } else {
++ qspi->soc_intc = NULL;
++ }
++
+ qspi->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(qspi->clk)) {
+ dev_warn(dev, "unable to get clock\n");
+@@ -1288,6 +1374,11 @@ static int __maybe_unused bcm_qspi_resum
+
+ bcm_qspi_hw_init(qspi);
+ bcm_qspi_chip_select(qspi, qspi->curr_cs);
++ if (qspi->soc_intc)
++ /* enable MSPI interrupt */
++ qspi->soc_intc->bcm_qspi_int_set(qspi->soc_intc, MSPI_DONE,
++ true);
++
+ ret = clk_enable(qspi->clk);
+ if (!ret)
+ spi_master_resume(qspi->master);
+--- a/drivers/spi/spi-bcm-qspi.h
++++ b/drivers/spi/spi-bcm-qspi.h
+@@ -48,10 +48,26 @@
+ (INTR_MSPI_DONE_MASK | \
+ INTR_MSPI_HALTED_MASK)
+
++#define QSPI_INTERRUPTS_ALL \
++ (MSPI_INTERRUPTS_ALL | \
++ BSPI_LR_INTERRUPTS_ALL)
++
+ struct platform_device;
+ struct dev_pm_ops;
+
+-struct bcm_qspi_soc_intc;
++enum {
++ MSPI_DONE = 0x1,
++ BSPI_DONE = 0x2,
++ BSPI_ERR = 0x4,
++ MSPI_BSPI_DONE = 0x7
++};
++
++struct bcm_qspi_soc_intc {
++ void (*bcm_qspi_int_ack)(struct bcm_qspi_soc_intc *soc_intc, int type);
++ void (*bcm_qspi_int_set)(struct bcm_qspi_soc_intc *soc_intc, int type,
++ bool en);
++ u32 (*bcm_qspi_get_int_status)(struct bcm_qspi_soc_intc *soc_intc);
++};
+
+ /* Read controller register*/
+ static inline u32 bcm_qspi_readl(bool be, void __iomem *addr)
+@@ -72,6 +88,22 @@ static inline void bcm_qspi_writel(bool
+ writel_relaxed(data, addr);
+ }
+
++static inline u32 get_qspi_mask(int type)
++{
++ switch (type) {
++ case MSPI_DONE:
++ return INTR_MSPI_DONE_MASK;
++ case BSPI_DONE:
++ return BSPI_LR_INTERRUPTS_ALL;
++ case MSPI_BSPI_DONE:
++ return QSPI_INTERRUPTS_ALL;
++ case BSPI_ERR:
++ return BSPI_LR_INTERRUPTS_ERROR;
++ }
++
++ return 0;
++}
++
+ /* The common driver functions to be called by the SoC platform driver */
+ int bcm_qspi_probe(struct platform_device *pdev,
+ struct bcm_qspi_soc_intc *soc_intc);
+--- /dev/null
++++ b/drivers/spi/spi-iproc-qspi.c
+@@ -0,0 +1,163 @@
++/*
++ * Copyright 2016 Broadcom Limited
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ */
++
++#include <linux/device.h>
++#include <linux/io.h>
++#include <linux/ioport.h>
++#include <linux/module.h>
++#include <linux/of.h>
++#include <linux/of_address.h>
++#include <linux/platform_device.h>
++#include <linux/slab.h>
++
++#include "spi-bcm-qspi.h"
++
++#define INTR_BASE_BIT_SHIFT 0x02
++#define INTR_COUNT 0x07
++
++struct bcm_iproc_intc {
++ struct bcm_qspi_soc_intc soc_intc;
++ struct platform_device *pdev;
++ void __iomem *int_reg;
++ void __iomem *int_status_reg;
++ spinlock_t soclock;
++ bool big_endian;
++};
++
++static u32 bcm_iproc_qspi_get_l2_int_status(struct bcm_qspi_soc_intc *soc_intc)
++{
++ struct bcm_iproc_intc *priv =
++ container_of(soc_intc, struct bcm_iproc_intc, soc_intc);
++ void __iomem *mmio = priv->int_status_reg;
++ int i;
++ u32 val = 0, sts = 0;
++
++ for (i = 0; i < INTR_COUNT; i++) {
++ if (bcm_qspi_readl(priv->big_endian, mmio + (i * 4)))
++ val |= 1UL << i;
++ }
++
++ if (val & INTR_MSPI_DONE_MASK)
++ sts |= MSPI_DONE;
++
++ if (val & BSPI_LR_INTERRUPTS_ALL)
++ sts |= BSPI_DONE;
++
++ if (val & BSPI_LR_INTERRUPTS_ERROR)
++ sts |= BSPI_ERR;
++
++ return sts;
++}
++
++static void bcm_iproc_qspi_int_ack(struct bcm_qspi_soc_intc *soc_intc, int type)
++{
++ struct bcm_iproc_intc *priv =
++ container_of(soc_intc, struct bcm_iproc_intc, soc_intc);
++ void __iomem *mmio = priv->int_status_reg;
++ u32 mask = get_qspi_mask(type);
++ int i;
++
++ for (i = 0; i < INTR_COUNT; i++) {
++ if (mask & (1UL << i))
++ bcm_qspi_writel(priv->big_endian, 1, mmio + (i * 4));
++ }
++}
++
++static void bcm_iproc_qspi_int_set(struct bcm_qspi_soc_intc *soc_intc, int type,
++ bool en)
++{
++ struct bcm_iproc_intc *priv =
++ container_of(soc_intc, struct bcm_iproc_intc, soc_intc);
++ void __iomem *mmio = priv->int_reg;
++ u32 mask = get_qspi_mask(type);
++ u32 val;
++ unsigned long flags;
++
++ spin_lock_irqsave(&priv->soclock, flags);
++
++ val = bcm_qspi_readl(priv->big_endian, mmio);
++
++ if (en)
++ val = val | (mask << INTR_BASE_BIT_SHIFT);
++ else
++ val = val & ~(mask << INTR_BASE_BIT_SHIFT);
++
++ bcm_qspi_writel(priv->big_endian, val, mmio);
++
++ spin_unlock_irqrestore(&priv->soclock, flags);
++}
++
++static int bcm_iproc_probe(struct platform_device *pdev)
++{
++ struct device *dev = &pdev->dev;
++ struct bcm_iproc_intc *priv;
++ struct bcm_qspi_soc_intc *soc_intc;
++ struct resource *res;
++
++ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
++ if (!priv)
++ return -ENOMEM;
++ soc_intc = &priv->soc_intc;
++ priv->pdev = pdev;
++
++ spin_lock_init(&priv->soclock);
++
++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "intr_regs");
++ priv->int_reg = devm_ioremap_resource(dev, res);
++ if (IS_ERR(priv->int_reg))
++ return PTR_ERR(priv->int_reg);
++
++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
++ "intr_status_reg");
++ priv->int_status_reg = devm_ioremap_resource(dev, res);
++ if (IS_ERR(priv->int_status_reg))
++ return PTR_ERR(priv->int_status_reg);
++
++ priv->big_endian = of_device_is_big_endian(dev->of_node);
++
++ bcm_iproc_qspi_int_ack(soc_intc, MSPI_BSPI_DONE);
++ bcm_iproc_qspi_int_set(soc_intc, MSPI_BSPI_DONE, false);
++
++ soc_intc->bcm_qspi_int_ack = bcm_iproc_qspi_int_ack;
++ soc_intc->bcm_qspi_int_set = bcm_iproc_qspi_int_set;
++ soc_intc->bcm_qspi_get_int_status = bcm_iproc_qspi_get_l2_int_status;
++
++ return bcm_qspi_probe(pdev, soc_intc);
++}
++
++static int bcm_iproc_remove(struct platform_device *pdev)
++{
++ return bcm_qspi_remove(pdev);
++}
++
++static const struct of_device_id bcm_iproc_of_match[] = {
++ { .compatible = "brcm,spi-nsp-qspi" },
++ { .compatible = "brcm,spi-ns2-qspi" },
++ {},
++};
++MODULE_DEVICE_TABLE(of, bcm_iproc_of_match);
++
++static struct platform_driver bcm_iproc_driver = {
++ .probe = bcm_iproc_probe,
++ .remove = bcm_iproc_remove,
++ .driver = {
++ .name = "bcm_iproc",
++ .pm = &bcm_qspi_pm_ops,
++ .of_match_table = bcm_iproc_of_match,
++ }
++};
++module_platform_driver(bcm_iproc_driver);
++
++MODULE_LICENSE("GPL v2");
++MODULE_AUTHOR("Kamal Dasu");
++MODULE_DESCRIPTION("SPI flash driver for Broadcom iProc SoCs");
More information about the lede-commits
mailing list