[source] uboot-kirkwood: add Zyxel NSA325 uboot
LEDE Commits
lede-commits at lists.infradead.org
Sat Feb 11 12:18:27 PST 2017
nbd pushed a commit to source.git, branch master:
https://git.lede-project.org/add1dd00813ccccfe5f1ee8e6bf04db7822b9fd5
commit add1dd00813ccccfe5f1ee8e6bf04db7822b9fd5
Author: Alberto Bursi <alberto.bursi at outlook.it>
AuthorDate: Mon Feb 6 11:39:21 2017 +0100
uboot-kirkwood: add Zyxel NSA325 uboot
add uboot for NSA325
Signed-off-by: Alberto Bursi <alberto.bursi at outlook.it>
---
package/boot/uboot-kirkwood/Makefile | 5 +
.../patches/008-nsa325-uboot-generic.patch | 709 +++++++++++++++++++++
2 files changed, 714 insertions(+)
diff --git a/package/boot/uboot-kirkwood/Makefile b/package/boot/uboot-kirkwood/Makefile
index 089188a..e06a680 100644
--- a/package/boot/uboot-kirkwood/Makefile
+++ b/package/boot/uboot-kirkwood/Makefile
@@ -52,6 +52,10 @@ define U-Boot/nsa310
NAME:=Zyxel NSA310
endef
+define U-Boot/nsa325
+ NAME:=Zyxel NSA325v1 and v2
+endef
+
define U-Boot/pogo_e02
NAME:=Cloud Engines Pogoplug E02
endef
@@ -70,6 +74,7 @@ UBOOT_TARGETS := \
ib62x0 ib62x0_second_stage \
iconnect iconnect_second_stage \
nsa310 \
+ nsa325 \
pogo_e02 pogo_e02_second_stage \
sheevaplug
diff --git a/package/boot/uboot-kirkwood/patches/008-nsa325-uboot-generic.patch b/package/boot/uboot-kirkwood/patches/008-nsa325-uboot-generic.patch
new file mode 100644
index 0000000..bb179b9
--- /dev/null
+++ b/package/boot/uboot-kirkwood/patches/008-nsa325-uboot-generic.patch
@@ -0,0 +1,709 @@
+diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
+index 819bd3b..6a2d578 100644
+--- a/arch/arm/mach-kirkwood/Kconfig
++++ b/arch/arm/mach-kirkwood/Kconfig
+@@ -55,6 +55,9 @@ config TARGET_NSA310
+ config TARGET_NSA310S
+ bool "Zyxel NSA310S"
+
++config TARGET_NSA325
++ bool "Zyxel NSA325 board"
++
+ endchoice
+
+ config SYS_SOC
+@@ -77,5 +80,6 @@ source "board/Seagate/goflexhome/Kconfig"
+ source "board/Seagate/nas220/Kconfig"
+ source "board/zyxel/nsa310/Kconfig"
+ source "board/zyxel/nsa310s/Kconfig"
++source "board/zyxel/nsa325/Kconfig"
+
+ endif
+diff --git a/board/zyxel/nsa325/Kconfig b/board/zyxel/nsa325/Kconfig
+new file mode 100644
+index 0000000..1fe5ead
+--- /dev/null
++++ b/board/zyxel/nsa325/Kconfig
+@@ -0,0 +1,12 @@
++if TARGET_NSA325
++
++config SYS_BOARD
++ default "nsa325"
++
++config SYS_VENDOR
++ default "zyxel"
++
++config SYS_CONFIG_NAME
++ default "nsa325"
++
++endif
+diff --git a/board/zyxel/nsa325/MAINTAINERS b/board/zyxel/nsa325/MAINTAINERS
+new file mode 100644
+index 0000000..130b4d9
+--- /dev/null
++++ b/board/zyxel/nsa325/MAINTAINERS
+@@ -0,0 +1,6 @@
++NSA325 BOARD
++M: Alberto Bursi <alberto.bursi at outlook.it>
++S: Maintained
++F: board/zyxel/nsa325/
++F: include/configs/nsa325.h
++F: configs/nsa325_defconfig
+diff --git a/board/zyxel/nsa325/Makefile b/board/zyxel/nsa325/Makefile
+new file mode 100644
+index 0000000..4ee953b
+--- /dev/null
++++ b/board/zyxel/nsa325/Makefile
+@@ -0,0 +1,13 @@
++#
++# (C) Copyright 2015 bodhi <mibodhi at gmail.com>
++#
++# Based on
++# (C) Copyright 2009
++# Marvell Semiconductor <www.marvell.com>
++# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
++#
++# SPDX-License-Identifier: GPL-2.0+
++#
++
++obj-y := nsa325.o
++
+diff --git a/board/zyxel/nsa325/kwbimage.cfg b/board/zyxel/nsa325/kwbimage.cfg
+new file mode 100644
+index 0000000..5a27d38
+--- /dev/null
++++ b/board/zyxel/nsa325/kwbimage.cfg
+@@ -0,0 +1,78 @@
++# Copyright (C) 2015 bodhi <mibodhi at gmail.com>
++#
++# Extracted from Zyxel GPL source for u-boot-1.1.4_NSA325v2
++#
++# See file CREDITS for list of people who contributed to this
++# project.
++#
++# This program is free software; you can redistribute it and/or
++# modify it under the terms of the GNU General Public License as
++# published by the Free Software Foundation; either version 2 of
++# the License, or (at your option) any later version.
++#
++# This program is distributed in the hope that it will be useful,
++# but WITHOUT ANY WARRANTY; without even the implied warranty of
++# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++# GNU General Public License for more details.
++#
++# You should have received a copy of the GNU General Public License
++# along with this program; if not, write to the Free Software
++# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
++# MA 02110-1301 USA
++#
++# Refer docs/README.kwimage for more details about how-to configure
++# and create kirkwood boot image
++#
++
++# Boot Media configurations
++#BOOT_FROM uart
++BOOT_FROM nand
++NAND_ECC_MODE default
++NAND_PAGE_SIZE 0x0800
++
++# SOC registers configuration using bootrom header extension
++# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
++
++# Configure RGMII-0 interface pad voltage to 1.8V
++DATA 0xFFD100e0 0x1b1b1b9b
++
++#Dram initalization
++DATA 0xFFD01400 0x4301503E # DDR Configuration register
++DATA 0xFFD01404 0xB9843000 # DDR Controller Control Low
++DATA 0xFFD01408 0x33137777 # DDR Timing (Low)
++DATA 0xFFD0140C 0x16000C55 # DDR Timing (High)
++DATA 0xFFD01410 0x04000000 # DDR Address Control
++DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
++DATA 0xFFD01418 0x00000000 # DDR Operation
++DATA 0xFFD0141C 0x00000672 # DDR Mode
++DATA 0xFFD01420 0x00000004 # DDR Extended Mode
++DATA 0xFFD01424 0x0000F14F # DDR Controller Control High
++DATA 0xFFD01428 0x000D6720 # DDR3 ODT Read Timing
++DATA 0xFFD0147C 0x0000B571 # DDR2 ODT Write Timing
++DATA 0xFFD01504 0x1FFFFFF1 # CS[0]n Size
++DATA 0xFFD01508 0x20000000 # CS[1]n Base address to 512Mb
++DATA 0xFFD0150C 0x1FFFFFF4 # CS[1]n Size 512Mb Window enabled for CS1
++DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
++DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
++DATA 0xFFD01494 0x00120000 # DDR ODT Control (Low)
++DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
++DATA 0xFFD0149C 0x0000E803 # CPU ODT Control
++
++DATA 0xFFD015D0 0x00000630
++DATA 0xFFD015D4 0x00000046
++DATA 0xFFD015D8 0x00000008
++DATA 0xFFD015DC 0x00000000
++DATA 0xFFD015E0 0x00000023
++DATA 0xFFD015E4 0x00203C18
++DATA 0xFFD01620 0x00384800
++DATA 0xFFD01480 0x00000001
++DATA 0xFFD20134 0x66666666
++DATA 0xFFD20138 0x00066666
++
++#Disable nsa325 hardware watchdog to allow successful kwbooting
++DATA 0xFFD10100 0x00004000 # set GPIO 14 to high to disable the watchdog
++DATA 0xFFD10104 0xFFFFBFFF # set GPIO 14 to output (to block any other input to it)
++
++# End of Header extension
++DATA 0x0 0x0
++
+diff --git a/board/zyxel/nsa325/nsa325.c b/board/zyxel/nsa325/nsa325.c
+new file mode 100644
+index 0000000..4cd1c0f
+--- /dev/null
++++ b/board/zyxel/nsa325/nsa325.c
+@@ -0,0 +1,265 @@
++/*
++ * Copyright (C) 2015 bodhi <mibodhi at gmail.com>
++ *
++ * Based on
++ * Copyright (C) 2014 Jason Plum <jplum at archlinuxarm.org>
++ *
++ * Based on nsa320.c originall written by
++ * Copyright (C) 2012 Peter Schildmann <linux at schildmann.info>
++ *
++ * Based on guruplug.c originally written by
++ * Siddarth Gore <gores at marvell.com>
++ * (C) Copyright 2009
++ * Marvell Semiconductor <www.marvell.com>
++ *
++ * See file CREDITS for list of people who contributed to this
++ * project.
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License as
++ * published by the Free Software Foundation; either version 2 of
++ * the License, or (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
++ * MA 02110-1301 USA
++ */
++
++#include <common.h>
++#include <miiphy.h>
++#include <asm/arch/soc.h>
++#include <asm/arch/mpp.h>
++#include <asm/arch/cpu.h>
++#include <asm/gpio.h>
++#include <asm/io.h>
++#include "nsa325.h"
++#include <asm/arch/gpio.h>
++
++DECLARE_GLOBAL_DATA_PTR;
++
++int board_early_init_f(void)
++{
++ /*
++ * default gpio configuration
++ * There are maximum 64 gpios controlled through 2 sets of registers
++ * the below configuration configures mainly initial LED status
++ */
++ mvebu_config_gpio(NSA325_VAL_LOW, NSA325_VAL_HIGH,
++ NSA325_OE_LOW, NSA325_OE_HIGH);
++
++ /* Multi-Purpose Pins Functionality configuration */
++ /* (all LEDs & power off active high) */
++ u32 kwmpp_config[] = {
++ MPP0_NF_IO2,
++ MPP1_NF_IO3,
++ MPP2_NF_IO4,
++ MPP3_NF_IO5,
++ MPP4_NF_IO6,
++ MPP5_NF_IO7,
++ MPP6_SYSRST_OUTn,
++ MPP7_GPO,
++ MPP8_TW_SDA, /* PCF8563 RTC chip */
++ MPP9_TW_SCK, /* connected to TWSI */
++ MPP10_UART0_TXD,
++ MPP11_UART0_RXD,
++ MPP12_GPO, /* HDD2 LED (green) */
++ MPP13_GPIO, /* HDD2 LED (red) */
++ MPP14_GPIO, /* MCU DATA pin (in) */
++ MPP15_GPIO, /* USB LED (green) */
++ MPP16_GPIO, /* MCU CLK pin (out) */
++ MPP17_GPIO, /* MCU ACT pin (out) */
++ MPP18_NF_IO0,
++ MPP19_NF_IO1,
++ MPP20_GPIO,
++ MPP21_GPIO, /* USB power */
++ MPP22_GPIO,
++ MPP23_GPIO,
++ MPP24_GPIO,
++ MPP25_GPIO,
++ MPP26_GPIO,
++ MPP27_GPIO,
++ MPP28_GPIO, /* SYS LED (green) */
++ MPP29_GPIO, /* SYS LED (orange) */
++ MPP30_GPIO,
++ MPP31_GPIO,
++ MPP32_GPIO,
++ MPP33_GPIO,
++ MPP34_GPIO,
++ MPP35_GPIO,
++ MPP36_GPIO, /* reset button */
++ MPP37_GPIO, /* copy button */
++ MPP38_GPIO, /* VID B0 */
++ MPP39_GPIO, /* COPY LED (green) */
++ MPP40_GPIO, /* COPY LED (red) */
++ MPP41_GPIO, /* HDD1 LED (green) */
++ MPP42_GPIO, /* HDD1 LED (red) */
++ MPP43_GPIO, /* HTP pin */
++ MPP44_GPIO, /* buzzer */
++ MPP45_GPIO, /* VID B1 */
++ MPP46_GPIO, /* power button */
++ MPP47_GPIO, /* HDD2 power */
++ MPP48_GPIO, /* power off */
++ 0
++ };
++ kirkwood_mpp_conf(kwmpp_config, NULL);
++ return 0;
++}
++
++int board_init(void)
++{
++
++ /* address of boot parameters */
++ gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
++
++ /* This disables the hardware watchdog in the mcu on this board. */
++ kw_gpio_set_valid(14, 1);
++ kw_gpio_direction_output(14, 0);
++ kw_gpio_set_value(14, 1);
++
++ return 0;
++}
++
++#ifdef CONFIG_RESET_PHY_R
++/* Configure and enable MV88E1318 PHY */
++void reset_phy(void)
++{
++ u16 reg;
++ u16 devadr;
++ char *name = "egiga0";
++
++ if (miiphy_set_current_dev(name))
++ return;
++
++ /* command to read PHY dev address */
++ if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
++ printf("Err..%s could not read PHY dev address\n",
++ __FUNCTION__);
++ return;
++ }
++
++ /* Set RGMII delay */
++ miiphy_write(name, devadr, MV88E1318_PGADR_REG, MV88E1318_MAC_CTRL_PG);
++ miiphy_read(name, devadr, MV88E1318_MAC_CTRL_REG, ®);
++ reg |= (MV88E1318_RGMII_RXTM_CTRL | MV88E1318_RGMII_TXTM_CTRL);
++ miiphy_write(name, devadr, MV88E1318_MAC_CTRL_REG, reg);
++ miiphy_write(name, devadr, MV88E1318_PGADR_REG, 0);
++
++ /* reset the phy */
++ miiphy_reset(name, devadr);
++
++ /* The ZyXEL NSA325 uses the 88E1310S Alaska (interface identical to 88E1318) */
++ /* and has an MCU attached to the LED[2] via tristate interrupt */
++ reg = 0;
++
++ /* switch to LED register page */
++ miiphy_write(name, devadr, MV88E1318_PGADR_REG, MV88E1318_LED_PG);
++ /* read out LED polarity register */
++ miiphy_read(name, devadr, MV88E1318_LED_POL_REG, ®);
++ /* clear 4, set 5 - LED2 low, tri-state */
++ reg &= ~(MV88E1318_LED2_4);
++ reg |= (MV88E1318_LED2_5);
++ /* write back LED polarity register */
++ miiphy_write(name, devadr, MV88E1318_LED_POL_REG, reg);
++ /* jump back to page 0, per the PHY chip documenation. */
++ miiphy_write(name, devadr, MV88E1318_PGADR_REG, 0);
++
++ /* Set the phy back to auto-negotiation mode. Onboard mcu sets it as 10Mbits/s on poweroff for WoL function */
++ miiphy_write(name, devadr, 0x4, 0x1e1);
++ miiphy_write(name, devadr, 0x9, 0x300);
++ /* Downshift */
++ miiphy_write(name, devadr, 0x10, 0x3860);
++ miiphy_write(name, devadr, 0x0, 0x9140);
++
++ printf("MV88E1318 PHY initialized on %s\n", name);
++
++}
++#endif /* CONFIG_RESET_PHY_R */
++
++#ifdef CONFIG_SHOW_BOOT_PROGRESS
++void show_boot_progress(int val)
++{
++ struct kwgpio_registers *gpio0 = (struct kwgpio_registers *)MVEBU_GPIO0_BASE;
++ u32 dout0 = readl(&gpio0->dout);
++ u32 blen0 = readl(&gpio0->blink_en);
++
++ struct kwgpio_registers *gpio1 = (struct kwgpio_registers *)MVEBU_GPIO1_BASE;
++ u32 dout1 = readl(&gpio1->dout);
++ u32 blen1 = readl(&gpio1->blink_en);
++
++ switch (val) {
++ case BOOTSTAGE_ID_DECOMP_IMAGE:
++ writel(blen0 & ~(SYS_GREEN_LED | SYS_ORANGE_LED), &gpio0->blink_en);
++ writel((dout0 & ~SYS_GREEN_LED) | SYS_ORANGE_LED, &gpio0->dout);
++ break;
++ case BOOTSTAGE_ID_RUN_OS:
++ writel(dout0 & ~SYS_ORANGE_LED, &gpio0->dout);
++ writel(blen0 | SYS_GREEN_LED, &gpio0->blink_en);
++ break;
++ case BOOTSTAGE_ID_NET_START:
++ writel(dout1 & ~COPY_RED_LED, &gpio1->dout);
++ writel((blen1 & ~COPY_RED_LED) | COPY_GREEN_LED, &gpio1->blink_en);
++ break;
++ case BOOTSTAGE_ID_NET_LOADED:
++ writel(blen1 & ~(COPY_RED_LED | COPY_GREEN_LED), &gpio1->blink_en);
++ writel((dout1 & ~COPY_RED_LED) | COPY_GREEN_LED, &gpio1->dout);
++ break;
++ case -BOOTSTAGE_ID_NET_NETLOOP_OK:
++ case -BOOTSTAGE_ID_NET_LOADED:
++ writel(dout1 & ~COPY_GREEN_LED, &gpio1->dout);
++ writel((blen1 & ~COPY_GREEN_LED) | COPY_RED_LED, &gpio1->blink_en);
++ break;
++ default:
++ if (val < 0) {
++ /* error */
++ printf("Error occured, error code = %d\n", -val);
++ writel(dout0 & ~SYS_GREEN_LED, &gpio0->dout);
++ writel(blen0 | SYS_ORANGE_LED, &gpio0->blink_en);
++ }
++ break;
++ }
++}
++#endif
++
++#if defined(CONFIG_KIRKWOOD_GPIO)
++/* Return GPIO button status */
++/*
++un-pressed:
++ gpio-36 (Reset Button ) in hi (act lo) - IRQ edge (clear )
++ gpio-37 (Copy Button ) in hi (act lo) - IRQ edge (clear )
++ gpio-46 (Power Button ) in lo (act hi) - IRQ edge (clear )
++pressed
++ gpio-36 (Reset Button ) in lo (act hi) - IRQ edge (clear )
++ gpio-37 (Copy Button ) in lo (act hi) - IRQ edge (clear )
++ gpio-46 (Power Button ) in hi (act lo) - IRQ edge (clear )
++*/
++
++static int
++do_read_button(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
++{
++ if (strcmp(argv[1], "power") == 0) {
++ kw_gpio_set_valid(BTN_POWER, GPIO_INPUT_OK);
++ kw_gpio_direction_input(BTN_POWER);
++ return !kw_gpio_get_value(BTN_POWER);
++ }
++ else if (strcmp(argv[1], "reset") == 0)
++ return kw_gpio_get_value(BTN_RESET);
++ else if (strcmp(argv[1], "copy") == 0)
++ return kw_gpio_get_value(BTN_COPY);
++ else
++ return -1;
++}
++
++
++U_BOOT_CMD(button, 2, 0, do_read_button,
++ "Return GPIO button status 0=off 1=on",
++ "- button power|reset|copy: test buttons states\n"
++);
++
++#endif
++
+diff --git a/board/zyxel/nsa325/nsa325.h b/board/zyxel/nsa325/nsa325.h
+new file mode 100644
+index 0000000..996653e
+--- /dev/null
++++ b/board/zyxel/nsa325/nsa325.h
+@@ -0,0 +1,77 @@
++/*
++ * Copyright (C) 2014 Jason Plum <jplum at archlinuxarm.org>
++ *
++ * Based on nsa320.h originall written by
++ * Copyright (C) 2012 Peter Schildmann <linux at schildmann.info>
++ *
++ * Based on guruplug.h originally written by
++ * Siddarth Gore <gores at marvell.com>
++ * (C) Copyright 2009
++ * Marvell Semiconductor <www.marvell.com>
++ *
++ * See file CREDITS for list of people who contributed to this
++ * project.
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License as
++ * published by the Free Software Foundation; either version 2 of
++ * the License, or (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
++ * MA 02110-1301 USA
++ */
++
++#ifndef __NSA325_H
++#define __NSA325_H
++
++/* low GPIO's */
++#define HDD2_GREEN_LED (1 << 12)
++#define HDD2_RED_LED (1 << 13)
++#define USB_GREEN_LED (1 << 15)
++#define USB_POWER (1 << 21)
++#define SYS_GREEN_LED (1 << 28)
++#define SYS_ORANGE_LED (1 << 29)
++
++#define PIN_USB_GREEN_LED 15
++#define PIN_USB_POWER 21
++
++#define NSA325_OE_LOW (~(HDD2_GREEN_LED | HDD2_RED_LED | \
++ USB_GREEN_LED | USB_POWER | \
++ SYS_GREEN_LED | SYS_ORANGE_LED))
++#define NSA325_VAL_LOW (SYS_GREEN_LED | USB_POWER)
++
++/* high GPIO's */
++#define COPY_GREEN_LED (1 << 7)
++#define COPY_RED_LED (1 << 8)
++#define HDD1_GREEN_LED (1 << 9)
++#define HDD1_RED_LED (1 << 10)
++#define HDD2_POWER (1 << 15)
++#define WATCHDOG_SIGNAL (1 << 14)
++
++#define NSA325_OE_HIGH (~(COPY_GREEN_LED | COPY_RED_LED | \
++ HDD1_GREEN_LED | HDD1_RED_LED | HDD2_POWER | WATCHDOG_SIGNAL ))
++#define NSA325_VAL_HIGH (WATCHDOG_SIGNAL | HDD2_POWER)
++
++/* PHY related */
++#define MV88E1318_PGADR_REG 22
++#define MV88E1318_MAC_CTRL_PG 2
++#define MV88E1318_MAC_CTRL_REG 21
++#define MV88E1318_RGMII_TXTM_CTRL (1 << 4)
++#define MV88E1318_RGMII_RXTM_CTRL (1 << 5)
++#define MV88E1318_LED_PG 3
++#define MV88E1318_LED_POL_REG 17
++#define MV88E1318_LED2_4 (1 << 4)
++#define MV88E1318_LED2_5 (1 << 5)
++
++#define BTN_POWER 46
++#define BTN_RESET 36
++#define BTN_COPY 37
++
++#endif /* __NSA325_H */
+diff --git a/configs/nsa325_defconfig b/configs/nsa325_defconfig
+new file mode 100644
+index 0000000..48e09cc
+--- /dev/null
++++ b/configs/nsa325_defconfig
+@@ -0,0 +1,18 @@
++CONFIG_ARM=y
++CONFIG_KIRKWOOD=y
++CONFIG_TARGET_NSA325=y
++CONFIG_BOOTDELAY=3
++CONFIG_SYS_PROMPT="NSA325> "
++# CONFIG_CMD_IMLS is not set
++# CONFIG_CMD_FLASH is not set
++CONFIG_SYS_NS16550=y
++CONFIG_CMD_FDT=y
++CONFIG_OF_LIBFDT=y
++CONFIG_CMD_SETEXPR=y
++CONFIG_CMD_DHCP=y
++CONFIG_CMD_NAND=y
++CONFIG_CMD_PING=y
++CONFIG_CMD_USB=y
++CONFIG_USB=y
++CONFIG_CMD_FAT=y
++CONFIG_USB_STORAGE=y
+\ No newline at end of file
+diff --git a/include/configs/nsa325.h b/include/configs/nsa325.h
+new file mode 100644
+index 0000000..e5a8e2a
+--- /dev/null
++++ b/include/configs/nsa325.h
+@@ -0,0 +1,170 @@
++/*
++ * (C) Copyright 2016 bodhi <mibodhi at gmail.com>
++ *
++ * Based on
++ * Copyright (C) 2014 Jason Plum <jplum at archlinuxarm.org>
++ * Based on
++ * Copyright (C) 2012 Peter Schildmann <linux at schildmann.info>
++ *
++ * Based on guruplug.h originally written by
++ * Siddarth Gore <gores at marvell.com>
++ * (C) Copyright 2009
++ * Marvell Semiconductor <www.marvell.com>
++ *
++ * See file CREDITS for list of people who contributed to this
++ * project.
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License as
++ * published by the Free Software Foundation; either version 2 of
++ * the License, or (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
++ * MA 02110-1301 USA
++ */
++
++#ifndef _CONFIG_NSA325_H
++#define _CONFIG_NSA325_H
++
++/*
++ * Version number information
++ */
++#define CONFIG_IDENT_STRING "\nZyXEL NSA325 2-Bay Power Media Server"
++
++/*
++ * High Level Configuration Options (easy to change)
++ */
++#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
++#define CONFIG_KIRKWOOD 1 /* SOC Family Name */
++#define CONFIG_KW88F6281 1 /* SOC Name */
++
++#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
++
++/*
++ * Misc Configuration Options
++ */
++#define CONFIG_SHOW_BOOT_PROGRESS 1 /* boot progess display (LED's) */
++
++/*
++ * Commands configuration
++ */
++#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
++#define CONFIG_SYS_MVFS /* Picks up Filesystem from mv-common.h */
++#define CONFIG_CMD_DHCP
++#define CONFIG_CMD_ENV
++#define CONFIG_CMD_IDE
++#define CONFIG_CMD_MII
++#define CONFIG_CMD_NAND
++#define CONFIG_CMD_PING
++#define CONFIG_CMD_USB
++#define CONFIG_CMD_DATE
++#define CONFIG_SYS_LONGHELP
++#define CONFIG_PREBOOT
++#define CONFIG_SYS_HUSH_PARSER
++#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
++
++/*
++ * mv-common.h should be defined after CMD configs since it used them
++ * to enable certain macros
++ */
++#include "mv-common.h"
++
++#undef CONFIG_SYS_PROMPT /* previously defined in mv-common.h */
++#define CONFIG_SYS_PROMPT "NSA325> " /* Command Prompt */
++
++/*
++ * Environment variables configurations
++ */
++#ifdef CONFIG_CMD_NAND
++#define CONFIG_ENV_IS_IN_NAND 1
++#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
++#else
++#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */
++#endif
++/*
++ * max 4k env size is enough, but in case of nand
++ * it has to be rounded to sector size
++ */
++#define CONFIG_ENV_SIZE 0x20000 /* 128k */
++#define CONFIG_ENV_ADDR 0xc0000
++#define CONFIG_ENV_OFFSET 0xc0000 /* env starts here */
++
++/*
++ * Default environment variables
++ */
++#define CONFIG_BOOTCOMMAND \
++ "ubi part ubi; " \
++ "ubi read 0x800000 kernel; " \
++ "bootm 0x800000"
++
++#define CONFIG_MTDPARTS \
++ "mtdparts=orion_nand:" \
++ "0x0c0000(uboot)," \
++ "0x80000(uboot_env)," \
++ "0x7ec0000(ubi)\0"
++
++#define CONFIG_EXTRA_ENV_SETTINGS \
++ "console=console=ttyS0,115200\0" \
++ "mtdids=nand0=orion_nand\0" \
++ "mtdparts="CONFIG_MTDPARTS \
++ "bootargs_root=\0"
++
++/*
++ * Ethernet Driver configuration
++ */
++#ifdef CONFIG_CMD_NET
++#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
++#define CONFIG_PHY_BASE_ADR 0x1
++#define CONFIG_PHY_GIGE
++#define CONFIG_NETCONSOLE
++#endif /* CONFIG_CMD_NET */
++
++/*
++ * SATA Driver configuration
++ */
++#ifdef CONFIG_MVSATA_IDE
++#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
++#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET
++#endif /* CONFIG_MVSATA_IDE */
++
++/*
++ * File system
++ */
++#define CONFIG_CMD_EXT2
++#define CONFIG_CMD_EXT4
++#define CONFIG_CMD_FAT
++#define CONFIG_CMD_JFFS2
++#define CONFIG_JFFS2_NAND
++#define CONFIG_JFFS2_LZO
++#define CONFIG_CMD_UBI
++#define CONFIG_CMD_UBIFS
++#define CONFIG_RBTREE
++#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
++#define CONFIG_MTD_PARTITIONS
++#define CONFIG_CMD_MTDPARTS
++#define CONFIG_LZO
++
++/*
++ * EFI partition
++ */
++#define CONFIG_EFI_PARTITION
++
++/*
++ * Date Time
++ */
++#ifdef CONFIG_CMD_DATE
++#define CONFIG_RTC_MV
++#define CONFIG_CMD_SNTP
++#define CONFIG_CMD_DNS
++#endif /* CONFIG_CMD_DATE */
++
++#define CONFIG_KIRKWOOD_GPIO /* Enable GPIO Support */
++
++#endif /* _CONFIG_NSA325_H */
More information about the lede-commits
mailing list