[source] apm821xx: add support for the Western Digital MyBook Live Series
LEDE Commits
lede-commits at lists.infradead.org
Fri Jul 22 03:50:15 PDT 2016
nbd pushed a commit to source.git, branch master:
https://git.lede-project.org/?p=source.git;a=commitdiff;h=dc7efaefb53d4671893add07934839eb8d44934d
commit dc7efaefb53d4671893add07934839eb8d44934d
Author: Christian Lamparter <chunkeey at googlemail.com>
AuthorDate: Wed Jul 20 15:44:54 2016 +0200
apm821xx: add support for the Western Digital MyBook Live Series
Hardware Highlights:
This patch adds support for Western Digital MyBook Live Series:
CPU: AMCC PowerPC UNKNOWN (PVR=12c41c83) at 800 MHz (PLB=200, OPB=100, EBC=100 MHz)
32 kB I-Cache 32 kB D-Cache, 256 kB L2-Cache, 32 kB OnChip Memory
Board: Apollo-3G - APM82181 Board, 1*SATA
DRAM: 256 MB (2x NT5TU64M16GG-AC)
FLASH: 512 kB (SST 39VF040)
Ethernet: 1xRGMII - 1 Gbit - Broadcom PHY BCM54610
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The MyBook Live Duo additionally features a 1x USB 2.0 host port
and can support a second hard-drive.
This target produces two images for a target.
1. ext4 image
The extracted/raw image can be directly installed on
the internal HDD via "dd if=img.ext4 of=/dev/sdX".
This can either be done in place with the stock MyBook Live
firmware via ssh. Or by removing the HDD and writing the image
with a different PC.
The the compressed images are useful for sysupgrade.
2. recovery.tar image for TFTP and Serial.
extract the recovery.tar to a TFTP server directory.
On the MyBook Live (Duo) serial port - Hit Enter during u-boot and insert:
# setenv serverip 192.168.1.254; setenv ipaddr 192.168.1.1; run net_self
Where 192.168.1.254 is your TFTP server.
Signed-off-by: Christian Lamparter <chunkeey at gmail.com>
---
target/linux/apm821xx/Makefile | 2 +-
.../linux/apm821xx/base-files/etc/board.d/01_leds | 3 +
.../apm821xx/base-files/etc/board.d/02_network | 1 +
target/linux/apm821xx/base-files/etc/diag.sh | 4 +
target/linux/apm821xx/base-files/lib/apm821xx.sh | 4 +
.../apm821xx/base-files/lib/preinit/79_move_config | 13 +
.../apm821xx/base-files/lib/upgrade/platform.sh | 13 +
.../apm821xx/base-files/lib/upgrade/wdbook.sh | 36 ++
target/linux/apm821xx/config-4.4 | 1 +
target/linux/apm821xx/dts/apollo3g-duo.dts | 18 +
target/linux/apm821xx/dts/apollo3g.dts | 34 ++
target/linux/apm821xx/dts/apollo3g.dtsi | 489 +++++++++++++++++++++
target/linux/apm821xx/image/Makefile | 83 +++-
target/linux/apm821xx/image/mbl_boot.scr | 6 +
target/linux/apm821xx/image/mbl_gen_hdd_img.sh | 27 ++
.../linux/apm821xx/image/mbl_gen_recovery_tar.sh | 92 ++++
.../patches-4.4/030-usb-dwc2-endian-fix.patch | 95 ++++
.../201-add-amcc-apollo3g-support.patch | 30 ++
target/linux/apm821xx/sata/config-default | 44 ++
target/linux/apm821xx/sata/target.mk | 13 +
20 files changed, 1006 insertions(+), 2 deletions(-)
diff --git a/target/linux/apm821xx/Makefile b/target/linux/apm821xx/Makefile
index eb34a3b..bd89c6b 100644
--- a/target/linux/apm821xx/Makefile
+++ b/target/linux/apm821xx/Makefile
@@ -11,7 +11,7 @@ CPU_TYPE:=464fp
FEATURES:=fpu dt gpio
MAINTAINER:=Chris Blake <chrisrblake93 at gmail.com>, \
Christian Lamparter <chunkeey at gmail.com>
-SUBTARGETS:=nand
+SUBTARGETS:=nand sata
KERNEL_PATCHVER:=4.4
diff --git a/target/linux/apm821xx/base-files/etc/board.d/01_leds b/target/linux/apm821xx/base-files/etc/board.d/01_leds
index d5f4cc9..bcc7a9f 100755
--- a/target/linux/apm821xx/base-files/etc/board.d/01_leds
+++ b/target/linux/apm821xx/base-files/etc/board.d/01_leds
@@ -16,6 +16,9 @@ mr24)
ucidef_set_led_wlan "wlan4" "WLAN4" "mr24:green:wifi4" "phy0tpt"
;;
+mbl)
+ ;;
+
*)
;;
esac
diff --git a/target/linux/apm821xx/base-files/etc/board.d/02_network b/target/linux/apm821xx/base-files/etc/board.d/02_network
index 4d53b2f..9525d8c 100755
--- a/target/linux/apm821xx/base-files/etc/board.d/02_network
+++ b/target/linux/apm821xx/base-files/etc/board.d/02_network
@@ -9,6 +9,7 @@ board_config_update
board=$(apm821xx_board_name)
case "$board" in
+mbl | \
mr24)
ucidef_set_interface_lan "eth0"
;;
diff --git a/target/linux/apm821xx/base-files/etc/diag.sh b/target/linux/apm821xx/base-files/etc/diag.sh
index 58301f8..bea66eb 100755
--- a/target/linux/apm821xx/base-files/etc/diag.sh
+++ b/target/linux/apm821xx/base-files/etc/diag.sh
@@ -5,6 +5,10 @@
get_status_led() {
case $(apm821xx_board_name) in
+ mbl)
+ status_led="mbl:green:power"
+ ;;
+
mr24)
status_led="mr24:green:power"
;;
diff --git a/target/linux/apm821xx/base-files/lib/apm821xx.sh b/target/linux/apm821xx/base-files/lib/apm821xx.sh
index 82f85c5..98e88cf 100755
--- a/target/linux/apm821xx/base-files/lib/apm821xx.sh
+++ b/target/linux/apm821xx/base-files/lib/apm821xx.sh
@@ -14,6 +14,10 @@ apm821xx_board_detect() {
name="mr24"
;;
+ *"MyBook Live"*)
+ name="mbl"
+ ;;
+
*)
name="unknown"
;;
diff --git a/target/linux/apm821xx/base-files/lib/preinit/79_move_config b/target/linux/apm821xx/base-files/lib/preinit/79_move_config
new file mode 100644
index 0000000..7c651b8
--- /dev/null
+++ b/target/linux/apm821xx/base-files/lib/preinit/79_move_config
@@ -0,0 +1,13 @@
+#!/bin/sh
+
+BOOTPART=/dev/sda1
+
+move_config() {
+ if [ -b $BOOTPART ]; then
+ mkdir -p /boot
+ mount -t ext4 -o rw,noatime $BOOTPART /boot
+ [ -f /boot/sysupgrade.tgz ] && mv -f /boot/sysupgrade.tgz /
+ fi
+}
+
+boot_hook_add preinit_mount_root move_config
diff --git a/target/linux/apm821xx/base-files/lib/upgrade/platform.sh b/target/linux/apm821xx/base-files/lib/upgrade/platform.sh
index ddf775f..d5b0986 100755
--- a/target/linux/apm821xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/apm821xx/base-files/lib/upgrade/platform.sh
@@ -11,6 +11,11 @@ platform_check_image() {
[ "$#" -gt 1 ] && return 1
case "$board" in
+ mbl)
+ mbl_do_platform_check $board "$1"
+ return $?;
+ ;;
+
mr24)
merakinand_do_platform_check $board "$1"
return $?;
@@ -41,6 +46,10 @@ platform_do_upgrade() {
local board=$(apm821xx_board_name)
case "$board" in
+ mbl)
+ mbl_do_upgrade "$ARGV"
+ ;;
+
*)
default_do_upgrade "$ARGV"
;;
@@ -51,6 +60,10 @@ platform_copy_config() {
local board=$(apm821xx_board_name)
case "$board" in
+ mbl)
+ mbl_copy_config
+ ;;
+
*)
;;
esac
diff --git a/target/linux/apm821xx/base-files/lib/upgrade/wdbook.sh b/target/linux/apm821xx/base-files/lib/upgrade/wdbook.sh
new file mode 100644
index 0000000..d734751
--- /dev/null
+++ b/target/linux/apm821xx/base-files/lib/upgrade/wdbook.sh
@@ -0,0 +1,36 @@
+. /lib/functions.sh
+
+get_magic_at() {
+ local file="$1"
+ local pos="$2"
+ get_image "$file" | dd bs=1 count=2 skip="$pos" 2>/dev/null | hexdump -v -n 2 -e '1/1 "%02x"'
+}
+
+mbl_do_platform_check() {
+ local board="$1"
+ local file="$2"
+ local magic
+
+ magic=$(get_magic_at "$file" 510)
+
+ [ "$magic" != "55aa" ] && {
+ echo "Failed to verify MBR boot signature."
+ return 1
+ }
+
+ return 0;
+}
+
+mbl_do_upgrade() {
+ sync
+ get_image "$1" | dd of=/dev/sda bs=2M conv=fsync
+ sleep 1
+}
+
+mbl_copy_config() {
+ mkdir -p /boot
+ [ -f /boot/uImage ] || mount -t ext4 -o rw,noatime /dev/sda1 /boot
+ cp -af "$CONF_TAR" /boot/
+ sync
+ umount /boot
+}
diff --git a/target/linux/apm821xx/config-4.4 b/target/linux/apm821xx/config-4.4
index 1e82e26..804e7e8 100644
--- a/target/linux/apm821xx/config-4.4
+++ b/target/linux/apm821xx/config-4.4
@@ -4,6 +4,7 @@ CONFIG_4xx=y
CONFIG_4xx_SOC=y
# CONFIG_ADVANCED_OPTIONS is not set
CONFIG_APM821xx=y
+# CONFIG_APOLLO3G is not set
# CONFIG_ARCHES is not set
CONFIG_ARCH_DMA_ADDR_T_64BIT=y
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
diff --git a/target/linux/apm821xx/dts/apollo3g-duo.dts b/target/linux/apm821xx/dts/apollo3g-duo.dts
new file mode 100644
index 0000000..874c469
--- /dev/null
+++ b/target/linux/apm821xx/dts/apollo3g-duo.dts
@@ -0,0 +1,18 @@
+/*
+ * Device Tree Source for AMCC Canyonlands (460EX)
+ *
+ * Copyright 2008 DENX Software Engineering, Stefan Roese <sr at denx.de>
+ * (c) Copyright 2010 Western Digital Technologies, Inc. All Rights Reserved.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+#include "apollo3g.dtsi"
+
+/ {
+ model = "MyBook Live Duo";
+};
diff --git a/target/linux/apm821xx/dts/apollo3g.dts b/target/linux/apm821xx/dts/apollo3g.dts
new file mode 100644
index 0000000..1b9f826
--- /dev/null
+++ b/target/linux/apm821xx/dts/apollo3g.dts
@@ -0,0 +1,34 @@
+/*
+ * Copyright 2008 DENX Software Engineering, Stefan Roese <sr at denx.de>
+ * (c) Copyright 2010 Western Digital Technologies, Inc. All Rights Reserved.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+#include "apollo3g.dtsi"
+
+/ {
+ model = "MyBook Live";
+};
+
+&SATA0 {
+ status = "disabled";
+};
+
+&USBOTG0 {
+ status = "disabled";
+};
+
+&gpio0 {
+ enable-usb {
+ status = "disabled";
+ };
+
+ enable-port0 {
+ status = "disabled";
+ };
+};
diff --git a/target/linux/apm821xx/dts/apollo3g.dtsi b/target/linux/apm821xx/dts/apollo3g.dtsi
new file mode 100644
index 0000000..bd15a8e
--- /dev/null
+++ b/target/linux/apm821xx/dts/apollo3g.dtsi
@@ -0,0 +1,489 @@
+/*
+ * Copyright 2008 DENX Software Engineering, Stefan Roese <sr at denx.de>
+ * (c) Copyright 2010 Western Digital Technologies, Inc. All Rights Reserved.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ */
+
+/ {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "amcc,apollo3g";
+ dcr-parent = <&{/cpus/cpu at 0}>;
+
+ aliases {
+ ethernet0 = &EMAC0;
+ serial0 = &UART0;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu at 0 {
+ device_type = "cpu";
+ model = "PowerPC,apm82181";
+ reg = <0x00000000>;
+ clock-frequency = <0>; /* Filled in by U-Boot */
+ timebase-frequency = <0>; /* Filled in by U-Boot */
+ i-cache-line-size = <32>;
+ d-cache-line-size = <32>;
+ i-cache-size = <32768>;
+ d-cache-size = <32768>;
+ dcr-controller;
+ dcr-access-method = "native";
+ next-level-cache = <&L2C0>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x00000000 0x00000000>; /* Filled in by U-Boot */
+ };
+
+ UIC0: interrupt-controller0 {
+ compatible = "ibm,uic-460ex","ibm,uic";
+ interrupt-controller;
+ cell-index = <0>;
+ dcr-reg = <0x0c0 0x009>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ };
+
+ UIC1: interrupt-controller1 {
+ compatible = "ibm,uic-460ex","ibm,uic";
+ interrupt-controller;
+ cell-index = <1>;
+ dcr-reg = <0x0d0 0x009>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ interrupts = <0x1e 0x4 0x1f 0x4>; /* cascade */
+ interrupt-parent = <&UIC0>;
+ };
+
+ UIC2: interrupt-controller2 {
+ compatible = "ibm,uic-460ex","ibm,uic";
+ interrupt-controller;
+ cell-index = <2>;
+ dcr-reg = <0x0e0 0x009>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ interrupts = <0xa 0x4 0xb 0x4>; /* cascade */
+ interrupt-parent = <&UIC0>;
+ };
+
+ UIC3: interrupt-controller3 {
+ compatible = "ibm,uic-460ex","ibm,uic";
+ interrupt-controller;
+ cell-index = <3>;
+ dcr-reg = <0x0f0 0x009>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ interrupts = <0x10 0x4 0x11 0x4>; /* cascade */
+ interrupt-parent = <&UIC0>;
+ };
+
+ OCM1: ocm at 400040000 {
+ compatible = "ibm,ocm";
+ status = "okay";
+ cell-index = <1>;
+ /* configured in U-Boot */
+ reg = <4 0x00040000 0x8000>; /* 32K */
+ };
+
+ SDR0: sdr {
+ compatible = "ibm,sdr-460ex";
+ dcr-reg = <0x00e 0x002>;
+ };
+
+ CPR0: cpr {
+ compatible = "ibm,cpr-460ex";
+ dcr-reg = <0x00c 0x002>;
+ };
+
+ CPM0: cpm {
+ compatible = "ibm,cpm";
+ dcr-access-method = "native";
+ dcr-reg = <0x160 0x003>;
+ unused-units = <0x00000100>;
+ idle-doze = <0x02000000>;
+ standby = <0xfeff791d>;
+ };
+
+ L2C0: l2c {
+ compatible = "ibm,l2-cache-apm82181", "ibm,l2-cache";
+ dcr-reg = <0x020 0x008
+ 0x030 0x008>;
+ cache-line-size = <32>;
+ cache-size = <262144>;
+ interrupt-parent = <&UIC1>;
+ interrupts = <11 1>;
+ };
+
+ plb {
+ compatible = "ibm,plb-460ex", "ibm,plb4";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges;
+ clock-frequency = <0>; /* Filled in by U-Boot */
+
+ SDRAM0: sdram {
+ compatible = "ibm,sdram-460ex", "ibm,sdram-405gp";
+ dcr-reg = <0x010 0x002>;
+ };
+
+ CRYPTO: crypto at 180000 {
+ compatible = "amcc,ppc460ex-crypto", "amcc,ppc4xx-crypto";
+ reg = <4 0x00180000 0x80400>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <0x1d 0x4>;
+ };
+
+ PKA: pka at 114000 {
+ device_type = "pka";
+ compatible = "ppc4xx-pka", "amcc,ppc4xx-pka";
+ reg = <0 0x00114000 0x4000>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <0x14 0x2>;
+ };
+
+ HWRNG: trng at 110000 {
+ compatible = "amcc,ppc460ex-rng", "ppc4xx-rng";
+ reg = <4 0x00110000 0x50>;
+ };
+
+ MAL0: mcmal {
+ compatible = "ibm,mcmal-460ex", "ibm,mcmal2";
+ descriptor-memory = "ocm";
+ dcr-reg = <0x180 0x062>;
+ num-tx-chans = <1>;
+ num-rx-chans = <1>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ interrupt-parent = <&UIC2>;
+ interrupts = < /*TXEOB*/ 0x6 0x4
+ /*RXEOB*/ 0x7 0x4
+ /*SERR*/ 0x3 0x4
+ /*TXDE*/ 0x4 0x4
+ /*RXDE*/ 0x5 0x4
+ /*TX0 COAL*/ 0x8 0x2
+ /*TX1 COAL 0x9 0x2*/
+ /*RX0 COAL*/ 0xc 0x2
+ /*RX1 COAL 0xd 0x2*/ >;
+ };
+
+ AHBDMA: dma at bffd0800 {
+ compatible = "snps,dma-spear1340";
+ reg = <4 0xbffd0800 0x400>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <25 4>;
+ #dma-cells = <3>;
+ /* use autoconfiguration for the dma setup */
+ };
+
+ SATA0: sata at bffd1000 {
+ compatible = "amcc,sata-460ex";
+ reg = <4 0xbffd1000 0x800>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <26 4>;
+ dmas = <&AHBDMA 0 0 1>;
+ dma-names = "sata-dma";
+ };
+
+ SATA1: sata at bffd1800 {
+ compatible = "amcc,sata-460ex";
+ reg = <4 0xbffd1800 0x800>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <27 4>;
+ dmas = <&AHBDMA 1 0 2>;
+ dma-names = "sata-dma";
+ };
+
+
+ USBOTG0: usbotg at bff80000 {
+ compatible = "snps,dwc2";
+ reg = <4 0xbff80000 0x10000>;
+ interrupt-parent = <&USBOTG0>;
+ interrupts = <0 1 2>;
+ #interrupt-cells = <1>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ interrupt-map = </* USB-OTG */ 0 &UIC2 0x1c 4
+ /* HIGH-POWER */ 1 &UIC1 0x1a 8
+ /* DMA */ 2 &UIC0 0xc 4>;
+ dr_mode = "host";
+ };
+
+ POB0: opb {
+ compatible = "ibm,opb-460ex", "ibm,opb";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0xb0000000 0x4 0xb0000000 0x50000000>;
+ clock-frequency = <0>; /* Filled in by U-Boot */
+
+ EBC0: ebc {
+ compatible = "ibm,ebc-460ex", "ibm,ebc";
+ dcr-reg = <0x012 0x002>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ clock-frequency = <0>; /* Filled in by U-Boot */
+ interrupts = <0x6 0x4>;
+ interrupt-parent = <&UIC1>;
+ /* ranges property are supplied by U-Boot */
+ ranges = <0x0 0x0 0xfff80000 0x00080000
+ 0x1 0x0 0x00000000 0x00000000
+ 0x2 0x0 0x00000000 0x00000000>;
+
+ /* Define device tree for Apollo3g NAS NOR flash
+ * The NOR doesn't work when "enable-button" GPIO
+ * is asserted.
+ */
+ nor_flash at 0,0 {
+ compatible = "amd,s29gl512n", "jedec-probe", "cfi-flash", "mtd-rom";
+ bank-width = <1>;
+ reg = <0x00000000 0x00000000 0x00080000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ /* Part of bootrom - Don't use it without a jump */
+ label = "free";
+ reg = <0x00000000 0x0001e000>;
+ };
+ partition at 1 {
+ label = "env";
+ reg = <0x0001e000 0x00002000>;
+ };
+ partition at 2 {
+ label = "uboot";
+ reg = <0x00020000 0x00050000>;
+ };
+
+ };
+
+ ndfc at 1,0 {
+ compatible = "ibm,ndfc";
+ reg = <0x00000001 0x00000000 0x00002000>;
+ ccr = <0x00001000>;
+ bank-settings = <0x80002222>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ status = "disabled";
+
+ nand {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+ };
+ };
+
+ gpio0: gpio0 at e0000000 {
+ compatible = "wd,mbl-gpio", "ti,74273";
+ reg-names = "dat";
+ reg = <0xe0000000 0x1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+
+ enable-phy {
+ /* toggle to reset EMAC PHY */
+ gpio-hog;
+ line-name = "enable EMAC PHY";
+ gpios = <0 1>;
+ output-low;
+ };
+
+ enable-button {
+ /* Defined in u-boot as: NOT_NOR
+ * "enables features other than NOR
+ * specifically, the buffer at CS2"
+ * (button).
+ *
+ * Note: This option is disabled as
+ * it prevents the system from being
+ * rebooted successfully.
+ */
+
+ gpio-hog;
+ line-name = "Enable Reset Button, disable NOR";
+ gpios = <1 0>;
+ output-low;
+ };
+
+ enable-usb {
+ gpio-hog;
+ line-name = "Power USB Core";
+ gpios = <2 1>;
+ output-low;
+ };
+
+ enable-port1 {
+ gpio-hog;
+ line-name = "Power Drive Port 1";
+ gpios = <3 1>;
+ output-low;
+ };
+
+ enable-port0 {
+ gpio-hog;
+ line-name = "Power Drive Port 0";
+ gpios = <7 1>;
+ output-low;
+ };
+ };
+
+ gpio1: gpio1 at e0100000 {
+ compatible = "wd,mbl-gpio", "ti,74244";
+ reg-names = "dat";
+ reg = <0xe0100000 0x1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ no-output;
+ };
+
+ UART0: serial at ef600300 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0xef600300 0x00000008>;
+ virtual-reg = <0xef600300>;
+ clock-frequency = <0>; /* Filled in by U-Boot */
+ current-speed = <0>; /* Filled in by U-Boot */
+ interrupt-parent = <&UIC1>;
+ interrupts = <0x1 0x4>;
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ power-red {
+ label = "mbl:red:power";
+ gpios = <&gpio0 4 0>;
+ linux,default-trigger = "panic";
+ };
+ power-green {
+ label = "mbl:green:power";
+ gpios = <&gpio0 5 0>;
+ linux,default-trigger = "default-on";
+ };
+ power-blue {
+ label = "mbl:blue:power";
+ gpios = <&gpio0 6 0>;
+ linux,default-trigger = "cpu0";
+ };
+ };
+
+ gpio_keys_polled {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <60>; /* 3 * 20 = 60ms */
+ autorepeat;
+ button at 1 {
+ label = "Reset button";
+ linux,code = <0x198>; /* KEY_RESTART */
+ gpios = <&gpio1 2 1>;
+ };
+ };
+
+ RGMII0: emac-rgmii at ef601500 {
+ compatible = "ibm,rgmii-405ex", "ibm,rgmii";
+ reg = <0xef601500 0x00000008>;
+ has-mdio;
+ };
+
+ TAH0: emac-tah at ef601350 {
+ compatible = "ibm,tah-460ex", "ibm,tah";
+ reg = <0xef601350 0x00000030>;
+ };
+
+ EMAC0: ethernet at ef600c00 {
+ device_type = "network";
+ compatible = "ibm,emac-405ex", "ibm,emac4sync";
+ interrupt-parent = <&EMAC0>;
+ interrupts = <0x0 0x1>;
+ #interrupt-cells = <1>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ interrupt-map = </*Status*/ 0x0 &UIC2 0x10 0x4
+ /*Wake*/ 0x1 &UIC2 0x14 0x4>;
+ reg = <0xef600c00 0x000000c4>;
+ local-mac-address = [000000000000]; /* Filled in by U-Boot */
+ mal-device = <&MAL0>;
+ mal-tx-channel = <0>;
+ mal-rx-channel = <0>;
+ cell-index = <0>;
+ max-frame-size = <9000>;
+ rx-fifo-size = <16384>;
+ tx-fifo-size = <2048>;
+ phy-mode = "rgmii";
+ phy-map = <0x00000000>;
+ rgmii-device = <&RGMII0>;
+ rgmii-channel = <0>;
+ tah-device = <&TAH0>;
+ tah-channel = <0>;
+ has-inverted-stacr-oc;
+ has-new-stacr-staopc;
+ };
+ };
+
+ ADMA: adma {
+ compatible = "amcc,apm82181-adma";
+ device_type = "dma";
+ #address-cells = <2>;
+ #size-cells = <1>;
+
+ dma-4channel at 1 {
+ compatible = "amcc,apm82181-dma-4channel";
+ cell-index = <1>;
+ label = "plb_dma1";
+ interrupt-parent = <&UIC0>;
+ interrupts = <0xd 0x4>;
+ pool_size = <0x4000>;
+ dcr-reg = <0x208 0x20f>;
+ };
+
+ dma-4channel at 2 {
+ compatible = "amcc,apm82181-dma-4channel";
+ cell-index = <2>;
+ label = "plb_dma2";
+ interrupt-parent = <&UIC0>;
+ interrupts = <0xe 0x4>;
+ pool_size = <0x4000>;
+ dcr-reg = <0x210 0x217>;
+ };
+
+ dma-4channel at 3 {
+ compatible = "amcc,apm82181-dma-4channel";
+ cell-index = <3>;
+ label = "plb_dma3";
+ interrupt-parent = <&UIC0>;
+ interrupts = <0xf 0x4>;
+ pool_size = <0x4000>;
+ dcr-reg = <0x218 0x21f>;
+ };
+ };
+
+ DMA: plb_dma at 400300200 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "amcc,dma";
+ cell-index = <0>;
+ reg = <4 00300200 200>;
+ dcr-reg = <0x100 0x13f>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <0>;
+ interrupt-map = < /* chan0 */ 0 &UIC0 12 4>;
+
+ dma-4channel at 0{
+ compatible = "amcc,dma-4channel";
+ cell-index = <0>;
+ label = "channel0";
+ reg = <0x100 0x107>;
+ };
+ };
+ };
+};
diff --git a/target/linux/apm821xx/image/Makefile b/target/linux/apm821xx/image/Makefile
index ba11bb2..9ba43d9 100644
--- a/target/linux/apm821xx/image/Makefile
+++ b/target/linux/apm821xx/image/Makefile
@@ -78,6 +78,87 @@ define Device/mr24
endef
TARGET_DEVICES += mr24
-$(eval $(call BuildImage))
+endif
+
+ifeq ($(SUBTARGET),sata)
+
+### Image scripts for the WD My Book Live Series ###
+define Build/boot-script
+ $(STAGING_DIR_HOST)/bin/mkimage -A powerpc -T script -C none -n "$(PROFILE) Boot Script" \
+ -d mbl_boot.scr \
+ $@.scr
+endef
+
+define Build/boot-img
+ $(RM) -rf $@.bootdir
+ mkdir -p $@.bootdir/boot
+
+ $(CP) $@.scr $@.bootdir/boot/boot.scr
+ $(CP) $@.dtb $@.bootdir/boot/$(DEVICE_DTB)
+ $(CP) $(word 1,$^) $@.bootdir/boot/uImage
+
+ genext2fs --block-size $(BLOCKSIZE) --size-in-blocks $$((1024 * $(BOOT_SIZE))) --root $@.bootdir $@.boot
+
+ # convert it to revision 1 - needed for u-boot ext2load
+ $(STAGING_DIR_HOST)/bin/tune2fs -O filetype $@.boot
+ $(STAGING_DIR_HOST)/bin/e2fsck -pDf $@.boot > /dev/null
+endef
+
+define Build/hdd-img
+ ./mbl_gen_hdd_img.sh $@ $@.boot $(word 2,$^)
+ $(if $(CONFIG_TARGET_IMAGES_GZIP),gzip -9n -c $@ > $(BIN_DIR)/$(notdir $@).gz)
+endef
+
+define Build/uRamdisk
+ $(call Image/mkfs/ext4)
+ gzip -9n -c $(KDIR)/root.ext4 > $(KDIR)/root.ext4.gz
+ $(STAGING_DIR_HOST)/bin/mkimage -A powerpc -T ramdisk -C gzip -n "$(PROFILE) rootfs" \
+ -d $(KDIR)/root.ext4.gz \
+ $@.uRamdisk
+endef
+
+define Build/recovery-tar
+ sh ./mbl_gen_recovery_tar.sh \
+ --profile $(DEVICE_PROFILE) \
+ --dtb $@.dtb \
+ --dtbname $(DEVICE_DTB) \
+ --kernel $@ \
+ --rootfs $@.uRamdisk \
+ $@
+endef
+
+define Device/MyBookLiveDefault
+ IMAGE_SIZE := 48m
+ BLOCKSIZE := 1024
+ DTB_SIZE := 16384
+ KERNEL := kernel-bin | gzip | uImage gzip
+ BOOT_SIZE := 8
+ IMAGES := rootfs.img recovery.tar
+ DEVICE_DTB := apollo3g.dtb
+ IMAGE/rootfs.img := boot-script | dtb | boot-img | hdd-img
+ IMAGE/recovery.tar := kernel-bin | dtb | uRamdisk | recovery-tar
+endef
+
+define Device/MyBookLiveSingle
+$(Device/MyBookLiveDefault)
+ DEVICE_TITLE := Western Digital My Book Live
+ DEVICE_DTS := apollo3g
+ DEVICE_PROFILE := apollo3g
+endef
+
+TARGET_DEVICES += MyBookLiveSingle
+
+define Device/MyBookLiveDuo
+$(Device/MyBookLiveDefault)
+ DEVICE_TITLE := Western Digital My Book Live Duo
+ DEVICE_PACKAGES := kmod-usb-dwc2 kmod-ledtrig-usbdev kmod-usb-storage kmod-fs-vfat wpad-mini
+ DEVICE_DTS := apollo3g-duo
+ DEVICE_PROFILE := ap2nc
+endef
+
+TARGET_DEVICES += MyBookLiveDuo
endif
+
+$(eval $(call BuildImage))
+
diff --git a/target/linux/apm821xx/image/mbl_boot.scr b/target/linux/apm821xx/image/mbl_boot.scr
new file mode 100644
index 0000000..062dc27
--- /dev/null
+++ b/target/linux/apm821xx/image/mbl_boot.scr
@@ -0,0 +1,6 @@
+setenv boot_args 'setenv bootargs root=/dev/sda2 rw rootfstype=ext4'
+setenv load_part1 'sata init; ext2load sata 1:1 ${kernel_addr_r} /boot/uImage; ext2load sata 1:1 ${fdt_addr_r} /boot/apollo3g.dtb'
+setenv load_part2 'sata init; ext2load sata 0:1 ${kernel_addr_r} /boot/uImage; ext2load sata 0:1 ${fdt_addr_r} /boot/apollo3g.dtb'
+setenv load_sata 'if run load_part1; then echo Loaded part 1; elif run load_part2; then echo Loaded part 2; fi'
+setenv boot_sata 'run load_sata; run boot_args addtty; bootm ${kernel_addr_r} - ${fdt_addr_r}'
+run boot_sata
diff --git a/target/linux/apm821xx/image/mbl_gen_hdd_img.sh b/target/linux/apm821xx/image/mbl_gen_hdd_img.sh
new file mode 100755
index 0000000..589dcf9
--- /dev/null
+++ b/target/linux/apm821xx/image/mbl_gen_hdd_img.sh
@@ -0,0 +1,27 @@
+#!/usr/bin/env bash
+
+set -x
+[ $# -eq 3 ] || {
+ echo "SYNTAX: $0 <file> <bootfs image> <rootfs image>"
+ exit 1
+}
+
+OUTPUT="$1"
+BOOTFS="$2"
+ROOTFS="$3"
+let "BOOTFSSIZE=(`stat -c%s "$2"` + 1048575) / 1048576"
+let "ROOTFSSIZE=(`stat -c%s "$3"` + 1048575) / 1048576"
+
+head=4
+sect=63
+
+set `ptgen -o $OUTPUT -h $head -s $sect -l 4096 -t 83 -p ${BOOTFSSIZE}M -t 83 -p ${ROOTFSSIZE}M`
+
+BOOTOFFSET="$(($1 / 512))"
+BOOTSIZE="$(($2 / 512))"
+ROOTFSOFFSET="$(($3 / 512))"
+ROOTFSSIZE="$(($4 / 512))"
+
+dd bs=512 if="$BOOTFS" of="$OUTPUT" seek="$BOOTOFFSET" conv=notrunc
+dd bs=512 if="$ROOTFS" of="$OUTPUT" seek="$ROOTFSOFFSET" conv=notrunc
+
diff --git a/target/linux/apm821xx/image/mbl_gen_recovery_tar.sh b/target/linux/apm821xx/image/mbl_gen_recovery_tar.sh
new file mode 100644
index 0000000..f871aef
--- /dev/null
+++ b/target/linux/apm821xx/image/mbl_gen_recovery_tar.sh
@@ -0,0 +1,92 @@
+#!/bin/sh
+
+# based on scripts/sysupgrade-nand.sh
+
+profile=""
+dtb=""
+dtbname=""
+kernel=""
+rootfs=""
+outfile=""
+err=""
+
+while [ "$1" ]; do
+ case "$1" in
+ "--profile")
+ profile="$2"
+ shift
+ shift
+ continue
+ ;;
+ "--dtb")
+ dtb="$2"
+ shift
+ shift
+ continue
+ ;;
+ "--dtbname")
+ dtbname="$2"
+ shift
+ shift
+ continue
+ ;;
+ "--kernel")
+ kernel="$2"
+ shift
+ shift
+ continue
+ ;;
+ "--rootfs")
+ rootfs="$2"
+ shift
+ shift
+ continue
+ ;;
+ *)
+ if [ ! "$outfile" ]; then
+ outfile=$1
+ shift
+ continue
+ else
+ shift
+ continue
+ fi
+ ;;
+ esac
+done
+
+if [ -z "$profile" -o ! -r "$dtb" -o ! -r "$kernel" -o ! -r "$rootfs" -o ! "$outfile" ]; then
+ echo "syntax: $0 [--profile profilename] [--dtb dtbimage] [--dtbname dtbname] [--kernel kernelimage] [--rootfs rootfs] out"
+ exit 1
+fi
+
+tmpdir="$( mktemp -d 2> /dev/null )"
+if [ -z "$tmpdir" ]; then
+ # try OSX signature
+ tmpdir="$( mktemp -t 'roottmp' -d )"
+fi
+
+if [ -z "$tmpdir" ]; then
+ exit 1
+fi
+
+mkdir -p "${tmpdir}/${profile}"
+[ -z "${dtb}" ] || cp "${dtb}" "${tmpdir}/${profile}/${dtbname}"
+[ -z "${rootfs}" ] || cp "${rootfs}" "${tmpdir}/${profile}/uRamdisk"
+[ -z "${kernel}" ] || cp "${kernel}" "${tmpdir}/${profile}/uImage"
+
+mtime=""
+if [ -n "$SOURCE_DATE_EPOCH" ]; then
+ mtime="--mtime=@${SOURCE_DATE_EPOCH}"
+fi
+
+(cd "$tmpdir"; tar cvf ${profile}.tar ${profile} ${mtime})
+err="$?"
+if [ -e "$tmpdir/${profile}.tar" ]; then
+ cp "$tmpdir/${profile}.tar" "$outfile"
+else
+ err=2
+fi
+rm -rf "$tmpdir"
+
+exit $err
diff --git a/target/linux/apm821xx/patches-4.4/030-usb-dwc2-endian-fix.patch b/target/linux/apm821xx/patches-4.4/030-usb-dwc2-endian-fix.patch
new file mode 100644
index 0000000..9078b6c
--- /dev/null
+++ b/target/linux/apm821xx/patches-4.4/030-usb-dwc2-endian-fix.patch
@@ -0,0 +1,95 @@
+From: Arnd Bergmann <arnd at arndb.de>
+Subject: [PATCH v4] usb: dwc2: fix regression on big-endian PowerPC/ARM systems
+Date: Fri, 13 May 2016 15:52:27 +0200
+Message-Id: <1463147559-544140-1-git-send-email-arnd at arndb.de>
+
+A patch that went into Linux-4.4 to fix big-endian mode on a Lantiq
+MIPS system unfortunately broke big-endian operation on PowerPC
+APM82181 as reported by Christian Lamparter, and likely other
+systems.
+
+It actually introduced multiple issues:
+
+- it broke big-endian ARM kernels: any machine that was working
+ correctly with a little-endian kernel is no longer using byteswaps
+ on big-endian kernels, which clearly breaks them.
+- On PowerPC the same thing must be true: if it was working before,
+ using big-endian kernels is now broken. Unlike ARM, 32-bit PowerPC
+ usually uses big-endian kernels, so they are likely all broken.
+- The barrier for dwc2_writel is on the wrong side of the __raw_writel(),
+ so the MMIO no longer synchronizes with DMA operations.
+- On architectures that require specific CPU instructions for MMIO
+ access, using the __raw_ variant may turn this into a pointer
+ dereference that does not have the same effect as the readl/writel.
+
+This patch is a simple revert for all architectures other than MIPS,
+in the hope that we can more easily backport it to fix the regression
+on PowerPC and ARM systems without breaking the Lantiq system again.
+
+We should follow this up with a more elaborate change to add runtime
+detection of endianness, to make sure it also works on all other
+combinations of architectures and implementations of the usb-dwc2
+device. That patch however will be fairly large and not appropriate
+for backports to stable kernels.
+
+Felipe suggested a different approach, using an endianness switching
+register to always put the device into LE mode, but unfortunately
+the dwc2 hardware does not provide a generic way to do that. Also,
+I see no practical way of addressing the problem more generally by
+patching architecture specific code on MIPS.
+
+Signed-off-by: Arnd Bergmann <arnd at arndb.de>
+Fixes: 95c8bc360944 ("usb: dwc2: Use platform endianness when accessing registers")
+---
+ drivers/usb/dwc2/core.h | 27 +++++++++++++++++++++++++++
+ 1 file changed, 27 insertions(+)
+
+diff --git a/drivers/usb/dwc2/core.h b/drivers/usb/dwc2/core.h
+index 3c58d633ce80..dec0b21fc626 100644
+--- a/drivers/usb/dwc2/core.h
++++ b/drivers/usb/dwc2/core.h
+@@ -64,6 +64,17 @@
+ DWC2_TRACE_SCHEDULER_VB(pr_fmt("%s: SCH: " fmt), \
+ dev_name(hsotg->dev), ##__VA_ARGS__)
+
++#ifdef CONFIG_MIPS
++/*
++ * There are some MIPS machines that can run in either big-endian
++ * or little-endian mode and that use the dwc2 register without
++ * a byteswap in both ways.
++ * Unlike other architectures, MIPS apparently does not require a
++ * barrier before the __raw_writel() to synchronize with DMA but does
++ * require the barrier after the __raw_writel() to serialize a set of
++ * writes. This set of operations was added specifically for MIPS and
++ * should only be used there.
++ */
+ static inline u32 dwc2_readl(const void __iomem *addr)
+ {
+ u32 value = __raw_readl(addr);
+@@ -90,6 +101,22 @@ static inline void dwc2_writel(u32 value, void __iomem *addr)
+ pr_info("INFO:: wrote %08x to %p\n", value, addr);
+ #endif
+ }
++#else
++/* Normal architectures just use readl/write */
++static inline u32 dwc2_readl(const void __iomem *addr)
++{
++ return readl(addr);
++}
++
++static inline void dwc2_writel(u32 value, void __iomem *addr)
++{
++ writel(value, addr);
++
++#ifdef DWC2_LOG_WRITES
++ pr_info("info:: wrote %08x to %p\n", value, addr);
++#endif
++}
++#endif
+
+ /* Maximum number of Endpoints/HostChannels */
+ #define MAX_EPS_CHANNELS 16
+--
+2.7.0
+
+
diff --git a/target/linux/apm821xx/patches-4.4/201-add-amcc-apollo3g-support.patch b/target/linux/apm821xx/patches-4.4/201-add-amcc-apollo3g-support.patch
new file mode 100644
index 0000000..8dc0924
--- /dev/null
+++ b/target/linux/apm821xx/patches-4.4/201-add-amcc-apollo3g-support.patch
@@ -0,0 +1,30 @@
+--- a/arch/powerpc/platforms/44x/Kconfig 2016-05-21 23:02:29.933525903 +0200
++++ b/arch/powerpc/platforms/44x/Kconfig 2016-05-21 23:06:50.843908233 +0200
+@@ -143,6 +143,17 @@ config CANYONLANDS
+ help
+ This option enables support for the AMCC PPC460EX evaluation board.
+
++config APOLLO3G
++ bool "Apollo3G"
++ depends on 44x
++ default n
++ select PPC44x_SIMPLE
++ select APM821xx
++ select IBM_EMAC_RGMII
++ select 460EX
++ help
++ This option enables support for the AMCC Apollo 3G board.
++
+ config GLACIER
+ bool "Glacier"
+ depends on 44x
+--- a/arch/powerpc/platforms/44x/ppc44x_simple.c 2016-05-21 23:02:29.933525903 +0200
++++ b/arch/powerpc/platforms/44x/ppc44x_simple.c 2016-05-21 23:06:01.130502053 +0200
+@@ -50,6 +50,7 @@ machine_device_initcall(ppc44x_simple, p
+ * board.c file for it rather than adding it to this list.
+ */
+ static char *board[] __initdata = {
++ "amcc,apollo3g",
+ "amcc,arches",
+ "amcc,bamboo",
+ "apm,bluestone",
diff --git a/target/linux/apm821xx/sata/config-default b/target/linux/apm821xx/sata/config-default
new file mode 100644
index 0000000..8b286fe
--- /dev/null
+++ b/target/linux/apm821xx/sata/config-default
@@ -0,0 +1,44 @@
+# CONFIG_IKAREM is not set
+CONFIG_APOLLO3G=y
+CONFIG_EXT4_FS=y
+CONFIG_DMADEVICES=y
+CONFIG_DMA_ENGINE=y
+CONFIG_DW_DMAC_CORE=y
+CONFIG_DW_DMAC=y
+# CONFIG_SATA_DWC_OLD_DMA is not set
+# CONFIG_DW_DMAC_PCI is not set
+CONFIG_ATA=y
+CONFIG_ATA_SFF=y
+CONFIG_ATA_BMDMA=y
+CONFIG_SATA_PMP=y
+CONFIG_GENERIC_PHY=y
+CONFIG_SATA_DWC=y
+# CONFIG_SATA_DWC_DEBUG is not set
+CONFIG_EXT4_FS=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_GENERIC=y
+CONFIG_GPIO_GENERIC_PLATFORM=y
+CONFIG_GPIO_74XX_MMIO=y
+CONFIG_BLK_DEV_DM=y
+CONFIG_BLK_DEV_DM_BUILTIN=y
+CONFIG_BLK_DEV_MD=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=4096
+CONFIG_MD=y
+CONFIG_MD_AUTODETECT=y
+# CONFIG_MD_LINEAR is not set
+# CONFIG_MD_MULTIPATH is not set
+CONFIG_MD_RAID0=y
+CONFIG_MD_RAID1=y
+# CONFIG_MD_RAID10 is not set
+# CONFIG_MD_RAID456 is not set
+CONFIG_BLK_DEV_RAM_SIZE=50331648
+CONFIG_PPC_EARLY_DEBUG=y
+CONFIG_PPC_EARLY_DEBUG_44x=y
+# CONFIG_PPC_EARLY_DEBUG_MEMCONS is not set
+CONFIG_PPC_EARLY_DEBUG_44x_PHYSHIGH=0x4
+CONFIG_PPC_EARLY_DEBUG_44x_PHYSLOW=0xef600300
diff --git a/target/linux/apm821xx/sata/target.mk b/target/linux/apm821xx/sata/target.mk
new file mode 100644
index 0000000..60efb50
--- /dev/null
+++ b/target/linux/apm821xx/sata/target.mk
@@ -0,0 +1,13 @@
+BOARDNAME := Devices which boot from SATA (NAS)
+FEATURES += ext4 usb
+DEFAULT_PACKAGES += badblocks block-mount e2fsprogs \
+ kmod-dm kmod-md-mod partx-utils
+
+define Target/Description
+ Build firmware images for APM82181 boards that boot from SATA.
+ For NAS like the MyBook Live Series.
+endef
+
+$(eval $(call $(if $(CONFIG_TARGET_ROOTFS_EXT4FS),RequireCommand,Ignore),genext2fs, \
+ Please install genext2fs. \
+))
More information about the lede-commits
mailing list