[source] ramips: TEW-692GR: fix switch and wireless

[LEDE Commits]

mkresin pushed a commit to source.git, branch master:
https://git.lede-project.org/?p=source.git;a=commitdiff;h=a7c6cf5182a3b20afb1c98d0d79247d6a9bc104b

commit a7c6cf5182a3b20afb1c98d0d79247d6a9bc104b
Author: Mathias Kresin <dev at kresin.me>
AuthorDate: Sun Aug 14 00:47:14 2016 +0200

    ramips: TEW-692GR: fix switch and wireless
    
    The AR8327 initvals were not copied to the DTS during the switch from
    mach file to device tree and broke the switch on the device.
    
    The former used PORT6 related initvals were wrong and have been
    corrected.
    
    The phy mode setting for the switch was missing in the DTS as well.
    
    The wireless requires an eeprom to work. The dual band wireless chips
    have both bands enabled by default but only one band per chip is
    working.
    
    The stock firmware uses the following mac addresses:
    
    LAN:    AA:BB:CC:DD:EE:E4
    WAN:    AA:BB:CC:DD:EE:E4
    2.4GHz: AA:BB:CC:DD:EE:E4
    5 GHz:  AA:BB:CC:DD:EE:E8
    
    Assuming the mac address range :E4 to :E8 is reserved for this device,
    the MAC addresses were reorder to have a unique MAC address for each
    interface:
    
    LAN:    AA:BB:CC:DD:EE:E4
    2.4GHz: AA:BB:CC:DD:EE:E4
    WAN:    AA:BB:CC:DD:EE:E5
    5 GHz:  AA:BB:CC:DD:EE:E8
    
    Signed-off-by: Mathias Kresin <dev at kresin.me>
---
 .../linux/ramips/base-files/etc/board.d/02_network |  3 +--
 target/linux/ramips/dts/TEW-692GR.dts              | 23 +++++++++++++++++++++-
 2 files changed, 23 insertions(+), 3 deletions(-)

diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index 0bf1a8a..73404d9 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -337,8 +337,7 @@ ramips_setup_macs()
 		wan_mac=$(macaddr_add "$lan_mac" 3)
 		;;
 	tew-692gr)
-		lan_mac=$(cat /sys/class/net/eth0/address)
-		wan_mac=$(macaddr_add "$lan_mac" 4)
+		wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 4)" 1)
 		;;
 	tiny-ac)
 		lan_mac=$(mtd_get_mac_ascii u-boot-env LAN_MAC_ADDR)
diff --git a/target/linux/ramips/dts/TEW-692GR.dts b/target/linux/ramips/dts/TEW-692GR.dts
index 5bba8a5..1a56710 100644
--- a/target/linux/ramips/dts/TEW-692GR.dts
+++ b/target/linux/ramips/dts/TEW-692GR.dts
@@ -86,7 +86,7 @@
 
 &ethernet {
 	status = "okay";
-	mtd-mac-address = <&factory 0x28>;
+	mtd-mac-address = <&factory 0x4>;
 
 	port at 0 {
 		phy-handle = <&phy0>;
@@ -98,6 +98,19 @@
 
 		phy0: ethernet-phy at 0 {
 			reg = <0>;
+			phy-mode = "rgmii";
+
+			qca,ar8327-initvals = <
+				0x04 0x07600000 /* PORT0 PAD MODE CTRL */
+				0x0c 0x07600000 /* PORT6 PAD MODE CTRL */
+				0x10 0x40000000 /* Power-on Strapping: 176-pin interface configuration */
+				0x50 0xc437c437 /* LED Control Register 0 */
+				0x54 0xc337c337 /* LED Control Register 1 */
+				0x58 0x00000000 /* LED Control Register 2 */
+				0x5c 0x03ffff00 /* LED Control Register 3 */
+				0x7c 0x0000007e /* PORT0_STATUS */
+				0x94 0x0000007e /* PORT6 STATUS */
+			>;
 		};
 	};
 };
@@ -117,10 +130,18 @@
 	host-bridge {
 		pci-bridge at 1 {
 			status = "okay";
+
+			wmac at 0,0 {
+				compatible = "ralink,rt2880-pci", "pciclass060400", "pciclass0604";
+				reg = < 0x10000 0 0 0 0 >;
+				ralink,2ghz = <0>;
+			};
 		};
 	};
 };
 
 &wmac {
+	status = "okay";
+	ralink,mtd-eeprom = <&factory 0x0>;
 	ralink,5ghz = <0>;
 };