[FS#1439] GL.iNet GL-B1300 Ethernet not working
LEDE Bugs
lede-bugs at lists.infradead.org
Fri Mar 16 17:00:24 PDT 2018
A new Flyspray task has been opened. Details are below.
User who did this - Alberto Bursi (bobafetthotmail1)
Attached to Project - OpenWrt/LEDE Project
Summary - GL.iNet GL-B1300 Ethernet not working
Task Type - Bug Report
Category - Base system
Status - Unconfirmed
Assigned To -
Operating System - All
Severity - Low
Priority - Very Low
Reported Version - Trunk
Due in Version - Undecided
Due Date - Undecided
Details - I've compiled from latest sources (r6469-5862f01) and flashed on the device. Then tried with the latest snapshot build, the result is the same.
After it has done rebooting ethernet isn't working anymore. Connecting/disconnecting cables does nothing, not even new messages in dmesg.
>From the uboot environment, ethernet works fine.
I connect to the device with the serial console, this is bootlog and some commands to show that the device does not have ethernet up.
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00117
S - IMAGE_VARIANT_STRING=DAABANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x00000021
S - Reset status Config, 0x00000010
S - Core 0 Frequency, 0 MHz
B - 261 - PBL, Start
B - 1338 - bootable_media_detect_entry, Start
B - 1678 - bootable_media_detect_success, Start
B - 1692 - elf_loader_entry, Start
B - 5069 - auth_hash_seg_entry, Start
B - 7210 - auth_hash_seg_exit, Start
B - 578929 - elf_segs_hash_verify_entry, Start
B - 696660 - PBL, End
B - 696683 - SBL1, Start
B - 787432 - pm_device_init, Start
D - 7 - pm_device_init, Delta
B - 788959 - boot_flash_init, Start
D - 54277 - boot_flash_init, Delta
B - 847376 - boot_config_data_table_init, Start
D - 3837 - boot_config_data_table_init, Delta - (419 Bytes)
B - 854589 - clock_init, Start
D - 7570 - clock_init, Delta
B - 866657 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:0
B - 870070 - sbl1_ddr_set_params, Start
B - 875167 - cpr_init, Start
D - 2 - cpr_init, Delta
B - 879548 - Pre_DDR_clock_init, Start
D - 5 - Pre_DDR_clock_init, Delta
D - 13175 - sbl1_ddr_set_params, Delta
B - 893285 - pm_driver_init, Start
D - 2 - pm_driver_init, Delta
B - 963512 - sbl1_wait_for_ddr_training, Start
D - 28 - sbl1_wait_for_ddr_training, Delta
B - 978987 - Image Load, Start
D - 140781 - QSEE Image Loaded, Delta - (274048 Bytes)
B - 1120195 - Image Load, Start
D - 1438 - SEC Image Loaded, Delta - (2048 Bytes)
B - 1130588 - Image Load, Start
D - 196809 - APPSBL Image Loaded, Delta - (402063 Bytes)
B - 1327792 - QSEE Execution, Start
D - 60 - QSEE Execution, Delta
B - 1334034 - SBL1, End
D - 639429 - SBL1, Delta
S - Flash Throughput, 2002 KB/s (678578 Bytes, 338844 us)
S - DDR Frequency, 537 MHz
U-Boot 2012.07 [Chaos Calmer 15.05.1,r35193] (Dec 19 2017 - 20:17:41)
smem ram ptable found: ver: 1 len: 3
DRAM: 256 MiB
machid : 0x8010000
NAND: SF: Detected MX25L25635E with page size 4 KiB, total 32 MiB
ipq_spi: page_size: 0x100, sector_size: 0x1000, size: 0x2000000
32 MiB
MMC:
In: serial
Out: serial
Err: serial
machid: 8010000
flash_type: 0
Net: MAC0 addr:e4:95:6e:43:30:3a
PHY ID1: 0x4d
PHY ID2: 0xd0b1
ipq40xx_ess_sw_init done
eth0
Hit "gl" key to stop booting: 0
SF: Detected MX25L25635E with page size 4 KiB, total 32 MiB
Checking calibration status...
Device have calibrated,checking test status...
Device haven tested, checking MAC info...
Device have MAC info, starting firmware...
eth0 PHY0 Down Speed :10 Half duplex
eth0 PHY1 Down Speed :10 Half duplex
eth0 PHY2 up Speed :1000 Full duplex
eth0 PHY3 Down Speed :10 Half duplex
eth0 PHY4 Down Speed :10 Half duplex
Using eth0 device
ping failed; host 192.168.1.2 is not alive
eth0 PHY0 Down Speed :10 Half duplex
eth0 PHY1 Down Speed :10 Half duplex
eth0 PHY2 up Speed :1000 Full duplex
eth0 PHY3 Down Speed :10 Half duplex
eth0 PHY4 Down Speed :10 Half duplex
Using eth0 device
ping failed; host 192.168.1.2 is not alive
eth0 PHY0 Down Speed :10 Half duplex
eth0 PHY1 Down Speed :10 Half duplex
eth0 PHY2 up Speed :1000 Full duplex
eth0 PHY3 Down Speed :10 Half duplex
eth0 PHY4 Down Speed :10 Half duplex
Using eth0 device
ping failed; host 192.168.1.2 is not alive
SF: Detected MX25L25635E with page size 4 KiB, total 32 MiB
## Booting kernel from FIT Image at 84000000 ...
Using 'config at 1' configuration
Trying 'kernel at 1' kernel subimage
Description: ARM OpenWrt Linux-4.14.25
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x840000e4
Data Size: 3025863 Bytes = 2.9 MiB
Architecture: ARM
OS: Linux
Load Address: 0x80208000
Entry Point: 0x80208000
Hash algo: crc32
Hash value: 0f3183e0
Hash algo: sha1
Hash value: 07910a0cb439c359762a9ef4e068ee490274a8c7
Verifying Hash Integrity ... crc32+ sha1+ OK
## Flattened Device Tree from FIT Image at 84000000
Using 'config at 1' configuration
Trying 'fdt at 1' FDT blob subimage
Description: ARM OpenWrt glinet_gl-b1300 device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x842e2de8
Data Size: 15859 Bytes = 15.5 KiB
Architecture: ARM
Hash algo: crc32
Hash value: e1ee0892
Hash algo: sha1
Hash value: a4ae2c4f6e123271dcf43d1e88cd9f2d53a8b60e
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x842e2de8
Uncompressing Kernel Image ... OK
Loading Device Tree to 86ff9000, end 86fffdf2 ... OK
ipq: fdt fixup unable to find compatible node
Using machid 0x8010000 from environment
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.14.25 (buildbot at builds) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r6460-bf4aa52)) #0 SMP Wed Mar 14 23:42:41 2018
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: GL.iNet GL-B1300
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] random: get_random_bytes called from start_kernel+0x88/0x3c4 with crng_init=0
[ 0.000000] percpu: Embedded 15 pages/cpu @cfdb0000 s29324 r8192 d23924 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 60928
[ 0.000000] Kernel command line: rootfsname=rootfs rootwait
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 235712K/245760K available (4354K kernel code, 146K rwdata, 1204K rodata, 1024K init, 252K bss, 10048K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0208000 - 0xc0740b88 (5347 kB)
[ 0.000000] .init : 0xc0900000 - 0xc0a00000 (1024 kB)
[ 0.000000] .data : 0xc0a00000 - 0xc0a24840 ( 147 kB)
[ 0.000000] .bss : 0xc0a26000 - 0xc0a652f4 ( 253 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns
[ 0.000008] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398046511096ns
[ 0.000022] Switching to timer-based delay loop, resolution 20ns
[ 0.000248] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000)
[ 0.000267] pid_max: default: 32768 minimum: 301
[ 0.000410] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000427] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.001036] CPU: Testing write buffer coherency: ok
[ 0.001665] Setting up static identity map for 0x80300000 - 0x80300060
[ 0.001797] Hierarchical SRCU implementation.
[ 0.002372] smp: Bringing up secondary CPUs ...
[ 0.004876] smp: Brought up 1 node, 4 CPUs
[ 0.004895] SMP: Total of 4 processors activated (384.00 BogoMIPS).
[ 0.004904] CPU: All CPU(s) started in SVC mode.
[ 0.008623] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.008798] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.008820] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.009019] pinctrl core: initialized pinctrl subsystem
[ 0.009964] NET: Registered protocol family 16
[ 0.010252] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.011286] cpuidle: using governor ladder
[ 0.011328] cpuidle: using governor menu
[ 0.027441] msm_bus_fabric_init_driver
[ 0.028041] usbcore: registered new interface driver usbfs
[ 0.028100] usbcore: registered new interface driver hub
[ 0.028178] usbcore: registered new device driver usb
[ 0.028225] pps_core: LinuxPPS API ver. 1 registered
[ 0.028235] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[ 0.028259] PTP clock support registered
[ 0.029344] clocksource: Switched to clocksource arch_sys_counter
[ 0.030220] NET: Registered protocol family 2
[ 0.030909] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.030953] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.031002] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.031110] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.031147] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.031345] NET: Registered protocol family 1
[ 0.032352] No memory allocated for crashlog
[ 0.032489] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[ 0.035689] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.035706] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.036777] random: fast init done
[ 0.040618] io scheduler noop registered
[ 0.040635] io scheduler deadline registered (default)
[ 0.043314] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000
[ 0.043402] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7
[ 0.043476] tcsr 1953000.ess_tcsr: setting ess interface select = 0
[ 0.043556] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222
[ 0.043776] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.045540] msm_serial 78af000.serial: msm_serial: detected port #0
[ 0.045588] msm_serial 78af000.serial: uartclk = 1843200
[ 0.045642] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 25, base_baud = 115200) is a MSM
[ 0.045669] msm_serial: console setup on port #0
[ 0.547847] console [ttyMSM0] enabled
[ 0.552768] msm_serial: driver initialized
[ 0.560280] loop: module loaded
[ 0.561329] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[ 0.564286] m25p80 spi0.0: mx25l25635e (32768 Kbytes)
[ 0.570495] 9 fixed-partitions partitions found on MTD device spi0.0
[ 0.575348] Creating 9 MTD partitions on "spi0.0":
[ 0.581802] 0x000000000000-0x000000040000 : "SBL1"
[ 0.587034] 0x000000040000-0x000000060000 : "MIBIB"
[ 0.591709] 0x000000060000-0x0000000c0000 : "QSEE"
[ 0.596477] 0x0000000c0000-0x0000000d0000 : "CDT"
[ 0.601336] 0x0000000d0000-0x0000000e0000 : "DDRPARAMS"
[ 0.606089] 0x0000000e0000-0x0000000f0000 : "APPSBLENV"
[ 0.611168] 0x0000000f0000-0x000000170000 : "APPSBL"
[ 0.616320] 0x000000170000-0x000000180000 : "ART"
[ 0.621572] 0x000000180000-0x000002000000 : "firmware"
[ 0.626383] 2 fit-fw partitions found on MTD device firmware
[ 0.630673] 0x000000180000-0x000000470000 : "kernel"
[ 0.637102] 0x000000466f00-0x000002000000 : "rootfs"
[ 0.641939] mtd: device 10 (rootfs) set to be root filesystem
[ 0.646514] 1 squashfs-split partitions found on MTD device rootfs
[ 0.652020] 0x0000006b0000-0x000002000000 : "rootfs_data"
[ 0.659288] libphy: ipq40xx_mdio: probed
[ 0.688293] ESS reset ok!
[ 0.721290] ESS reset ok!
[ 1.149729] libphy: Fixed MDIO Bus: probed
[ 1.153419] libphy: PHY 90000.mdio:04 not found
[ 1.229594] ------------[ cut here ]------------
[ 1.229642] WARNING: CPU: 1 PID: 1 at mm/vmalloc.c:1525 release_nodes+0x198/0x1bc
[ 1.233285] Trying to vfree() nonexistent vm area (d08e8000)
[ 1.240687] Modules linked in:
[ 1.246389] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.14.25 #0
[ 1.249255] Hardware name: Generic DT based system
[ 1.255442] [] (unwind_backtrace) from [] (show_stack+0x10/0x14)
[ 1.260036] [] (show_stack) from [] (dump_stack+0x88/0x9c)
[ 1.267931] [] (dump_stack) from [] (__warn+0xe4/0x100)
[ 1.274959] [] (__warn) from [] (warn_slowpath_fmt+0x38/0x48)
[ 1.281819] [] (warn_slowpath_fmt) from [] (release_nodes+0x198/0x1bc)
[ 1.289463] [] (release_nodes) from [] (really_probe+0x1a8/0x27c)
[ 1.297618] [] (really_probe) from [] (__driver_attach+0x8c/0xb0)
[ 1.305517] [] (__driver_attach) from [] (bus_for_each_dev+0x4c/0xa0)
[ 1.313331] [] (bus_for_each_dev) from [] (bus_add_driver+0xe8/0x200)
[ 1.321489] [] (bus_add_driver) from [] (driver_register+0xa8/0xe4)
[ 1.329646] [] (driver_register) from [] (do_one_initcall+0xc0/0x184)
[ 1.337465] [] (do_one_initcall) from [] (kernel_init_freeable+0x13c/0x1d0)
[ 1.345796] [] (kernel_init_freeable) from [] (kernel_init+0x8/0x110)
[ 1.354301] [] (kernel_init) from [] (ret_from_fork+0x14/0x2c)
[ 1.362702] ---[ end trace 250c0be6176c0372 ]---
[ 1.370119] ess_edma: probe of c080000.edma failed with error -5
[ 1.375478] i2c /dev entries driver
[ 1.410267] NET: Registered protocol family 10
[ 1.411725] Segment Routing with IPv6
[ 1.413712] NET: Registered protocol family 17
[ 1.417400] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.422085] 8021q: 802.1Q VLAN Support v1.8
�[ 1.449573] VFS: Mounted root (squashfs filesystem) readonly on device 31:10.
[ 1.451147] Freeing unused kernel memory: 1024K
[ 2.306363] init: Console is alive
[ 2.306597] init: - watchdog -
[ 3.773901] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.319843] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 4.320433] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 4.326325] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f665 hci version 0x100 quirks 0x02010010
[ 4.332940] xhci-hcd xhci-hcd.0.auto: irq 94, io mem 0x08a00000
[ 4.348359] hub 1-0:1.0: USB hub found
[ 4.349153] hub 1-0:1.0: 1 port detected
[ 4.352351] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 4.355199] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 4.360611] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.368563] hub 2-0:1.0: USB hub found
[ 4.376445] hub 2-0:1.0: 1 port detected
[ 4.499902] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 4.500448] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 4.506216] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f665 hci version 0x100 quirks 0x02010010
[ 4.512944] xhci-hcd xhci-hcd.1.auto: irq 95, io mem 0x06000000
[ 4.521469] hub 3-0:1.0: USB hub found
[ 4.526592] hub 3-0:1.0: 1 port detected
[ 4.530786] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 4.534454] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 4.539946] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.547821] hub 4-0:1.0: USB hub found
[ 4.555681] hub 4-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 4.560984] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.579575] init: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 9.186982] jffs2: notice: (161) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 1 orphan) and 1 of xref (1 dead, 0 orphan) found.
[ 9.208874] mount_root: switching to jffs2 overlay
[ 9.230511] overlayfs: upper fs does not support tmpfile.
[ 9.244336] urandom-seed: Seeding with /etc/urandom.seed
[ 9.317375] procd: - early -
[ 9.317514] procd: - watchdog -
[ 9.980551] procd: - watchdog -
[ 9.983341] procd: - ubus -
[ 10.087188] procd: - init -
Please press Enter to activate this console.
[ 10.271602] kmodloader: loading kernel modules from /etc/modules.d/*
[ 10.274673] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.703428] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[ 10.703465] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[ 10.712114] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.083361] nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
[ 11.311032] xt_time: kernel timezone is -0000
[ 11.532737] PPP generic driver version 2.4.2
[ 11.533719] NET: Registered protocol family 24
[ 11.725866] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/firmware-6.bin failed with error -2
[ 11.725917] ath10k_ahb a000000.wifi: Falling back to user helper
[ 11.766796] firmware ath10k!QCA4019!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 12.305593] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003900ff sub 0000:0000
[ 12.305639] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 12.318443] ath10k_ahb a000000.wifi: firmware ver 10.4-3.4-00104 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps crc32 6c332c67
[ 12.364240] ath10k_ahb a000000.wifi: board_file api 2 bmi_id 0:16 crc32 b4b4d99e
[ 13.712909] ath10k_ahb a000000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 512 raw 0 hwcrypto 1
[ 13.924563] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/firmware-6.bin failed with error -2
[ 13.924611] ath10k_ahb a800000.wifi: Falling back to user helper
[ 14.058909] firmware ath10k!QCA4019!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 14.059172] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003900ff sub 0000:0000
[ 14.066880] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 14.081139] ath10k_ahb a800000.wifi: firmware ver 10.4-3.4-00104 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps crc32 6c332c67
[ 14.125418] ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:17 crc32 b4b4d99e
[ 15.473395] ath10k_ahb a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 512 raw 0 hwcrypto 1
[ 15.542473] kmodloader: done loading kernel modules from /etc/modules.d/*
BusyBox v1.27.2 () built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r6469-5862f01
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root at OpenWrt:/# ip a
1: lo: mtu 65536 qdisc noqueue state UNKNOWN qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
4: wlan0: mtu 1500 qdisc noop state DOWN qlen 1000
link/ether e4:95:6e:43:30:3a brd ff:ff:ff:ff:ff:ff
5: wlan1: mtu 1500 qdisc noop state DOWN qlen 1000
link/ether e4:95:6e:43:30:3b brd ff:ff:ff:ff:ff:ff
root at OpenWrt:/# uci show network
network.loopback=interface
network.loopback.ifname='lo'
network.loopback.proto='static'
network.loopback.ipaddr='127.0.0.1'
network.loopback.netmask='255.0.0.0'
network.globals=globals
network.globals.ula_prefix='fd8d:fcc2:d3a6::/48'
network.lan=interface
network.lan.type='bridge'
network.lan.ifname='eth0'
network.lan.proto='static'
network.lan.ipaddr='192.168.1.1'
network.lan.netmask='255.255.255.0'
network.lan.ip6assign='60'
network.wan=interface
network.wan.ifname='eth1'
network.wan.proto='dhcp'
network.wan6=interface
network.wan6.ifname='eth1'
network.wan6.proto='dhcpv6'
network. at switch[0]=switch
network. at switch[0].name='switch0'
network. at switch[0].reset='1'
network. at switch[0].enable_vlan='1'
network. at switch_vlan[0]=switch_vlan
network. at switch_vlan[0].device='switch0'
network. at switch_vlan[0].vlan='1'
network. at switch_vlan[0].ports='3 4 0'
More information can be found at the following URL:
https://bugs.openwrt.org/index.php?do=details&task_id=1439
More information about the lede-bugs
mailing list