[FS#1305] Not working UAS driver for usb hdd case ORICO 2599US3-V1
LEDE Bugs
lede-bugs at lists.infradead.org
Sun Jan 28 07:55:50 PST 2018
A new Flyspray task has been opened. Details are below.
User who did this - emvova (emvova)
Attached to Project - OpenWrt/LEDE Project
Summary - Not working UAS driver for usb hdd case ORICO 2599US3-V1
Task Type - Bug Report
Category - Packages
Status - Unconfirmed
Assigned To -
Operating System - All
Severity - Low
Priority - Very Low
Reported Version - Trunk
Due in Version - Undecided
Due Date - Undecided
Details - - Xiaomi Mi Router 3G
- OpenWrt/LEDE trunk with kmod-usb-storage-uas package.
- After fresh install trunk version and kmod-usb-storage-uas drivers for USB storage have error:
[ 457.174784] scsi host0: uas
[ 457.178931] xhci-mtk 1e1c0000.xhci: ERROR Transfer event for disabled endpoint or incorrect stream ring
[ 457.188303] xhci-mtk 1e1c0000.xhci: @000000000fded170 0ee20000 00000000 05000000 01058001
[ 457.196514] xhci-mtk 1e1c0000.xhci: ERROR Transfer event for disabled endpoint or incorrect stream ring
[ 457.205879] xhci-mtk 1e1c0000.xhci: @000000000fded180 0ee20100 00000000 05000000 01078001
[ 464.441727] Data buffer not 16 bytes aligned: 8ee2c458
[ 464.469820] Data buffer not 16 bytes aligned: 8ee2c0d8
[ 464.477079] Data buffer not 16 bytes aligned: 8ee2c368
[ 477.979944] scsi 0:0:0:0: tag#0 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD IN
[ 477.987509] scsi 0:0:0:0: tag#0 CDB: opcode=0x12 12 00 00 00 24 00
[ 479.029938] scsi host0: uas_eh_bus_reset_handler FAILED to get lock err -16
[ 479.036896] scsi 0:0:0:0: Device offlined - not ready after error recovery
FULL log
[ 0.000000] Linux version 4.9.77 (buildbot at builds) (gcc version 5.5.0 (OpenWrt GCC 5.5.0 r5972-74beb6f) ) #0 SMP Sun Jan 28 07:53:50 2018
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is Xiaomi Mi Router 3G
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 10000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] On node 0 totalpages: 65536
[ 0.000000] free_area_init_node: node 0, pgdat 80519c20, node_mem_map 81003000
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65536 pages, LIFO batch:15
[ 0.000000] percpu: Embedded 12 pages/cpu @8120f000 s17744 r8192 d23216 u49152
[ 0.000000] pcpu-alloc: s17744 r8192 d23216 u49152 alloc=12*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Writing ErrCtl register=00022211
[ 0.000000] Readback ErrCtl register=00022211
[ 0.000000] Memory: 253888K/262144K available (4083K kernel code, 221K rwdata, 920K rodata, 204K init, 272K bss, 8256K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:256
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.000010] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[ 0.007796] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.070423] pid_max: default: 32768 minimum: 301
[ 0.075160] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.081686] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.095326] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.095339] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.095351] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.095506] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.177455] Synchronize counters for CPU 1:
[ 0.177457] done.
[ 0.190893] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.190901] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.190910] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.190995] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.269476] Synchronize counters for CPU 2:
[ 0.269477] done.
[ 0.279363] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.279371] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.279379] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.279472] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.354659] Synchronize counters for CPU 3:
[ 0.354660] done.
[ 0.360901] Brought up 4 CPUs
[ 0.367821] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.377613] futex hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.383863] pinctrl core: initialized pinctrl subsystem
[ 0.389755] NET: Registered protocol family 16
[ 0.403515] FPU Affinity set after 11720 emulations
[ 0.449650] pull PCIe RST: RALINK_RSTCTRL = 4000000
[ 0.754956] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.760005] ***** Xtal 40MHz *****
[ 0.763360] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.768459] Port 0 N_FTS = 1b105000
[ 0.771934] Port 1 N_FTS = 1b105000
[ 0.775368] Port 2 N_FTS = 1b102800
[ 1.930662] PCIE2 no card, disable it(RST&CLK)
[ 1.935027] -> 21007f2
[ 1.937422] PCIE0 enabled
[ 1.940014] PCIE1 enabled
[ 1.942610] PCI host bridge /pcie at 1e140000 ranges:
[ 1.947395] MEM 0x0000000060000000..0x000000006fffffff
[ 1.952552] IO 0x000000001e160000..0x000000001e16ffff
[ 1.957754] PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 2.009324] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 2.015156] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 2.020966] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 2.027884] PCI host bridge to bus 0000:00
[ 2.031941] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 2.038727] pci_bus 0000:00: root bus resource [io 0xffffffff]
[ 2.044616] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 2.051341] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 2.059269] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 2.059300] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 2.059312] pci 0000:00:00.0: reg 0x14: [mem 0x60300000-0x6030ffff]
[ 2.059374] pci 0000:00:00.0: supports D1
[ 2.059383] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 2.059617] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 2.059641] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 2.059656] pci 0000:00:01.0: reg 0x14: [mem 0x60310000-0x6031ffff]
[ 2.059705] pci 0000:00:01.0: supports D1
[ 2.059713] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 2.060115] pci 0000:01:00.0: [14c3:7603] type 00 class 0x028000
[ 2.060145] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
[ 2.060267] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 2.060466] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 2.060648] pci 0000:02:00.0: [14c3:7662] type 00 class 0x028000
[ 2.060683] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[ 2.060728] pci 0000:02:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 2.060816] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 2.061016] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 2.061034] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 02
[ 2.061093] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 2.067602] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.074545] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 2.081087] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.088015] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 2.094738] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff]
[ 2.101497] pci 0000:00:01.0: BAR 9: assigned [mem 0x60200000-0x602fffff pref]
[ 2.108649] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
[ 2.115404] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]
[ 2.122138] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff]
[ 2.128881] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 2.133788] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 2.140555] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit]
[ 2.147793] pci 0000:02:00.0: BAR 6: assigned [mem 0x60200000-0x6020ffff pref]
[ 2.154968] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 2.159885] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff]
[ 2.166635] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff pref]
[ 2.173807] BAR0 at slot 0 = 0
[ 2.176821] bus=0x0, slot = 0x0
[ 2.179929] BAR0 at slot 1 = 0
[ 2.182941] bus=0x0, slot = 0x1
[ 2.186059] bus=0x1, slot = 0x0, irq=0xff
[ 2.190052] bus=0x2, slot = 0x1, irq=0xff
[ 2.195374] clocksource: Switched to clocksource GIC
[ 2.201886] NET: Registered protocol family 2
[ 2.206991] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 2.213879] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 2.220380] TCP: Hash tables configured (established 2048 bind 2048)
[ 2.226740] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 2.232503] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 2.238991] NET: Registered protocol family 1
[ 2.243310] PCI: CLS 80 bytes, default 32
[ 2.475320] 4 CPUs re-calibrate udelay(lpj = 2924544)
[ 2.481720] Crashlog allocated RAM at address 0x3f00000
[ 2.487253] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[ 2.497205] random: fast init done
[ 2.503153] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.508957] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 2.521334] io scheduler noop registered
[ 2.525170] io scheduler deadline registered (default)
[ 2.530800] gpio-export gpio_export: 1 gpio(s) exported
[ 2.536631] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 2.546698] console [ttyS0] disabled
[ 2.550247] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 18, base_baud = 3125000) is a 16550A
[ 2.559239] console [ttyS0] enabled
[ 2.566106] bootconsole [early0] disabled
[ 2.575604] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
[ 2.582660] Allocate 16 byte aligned buffer: 80588360
[ 2.587709] Enable NFI Clock
[ 2.590575] # MTK NAND # : Use HW ECC
[ 2.594233] Device not found, ID: c8d1
[ 2.597975] Not Support this Device!
[ 2.601702] chip_mode=00000001
[ 2.604750] Support this Device in MTK table! c8d1
[ 2.609710] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
[ 2.616186] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xd1
[ 2.622507] nand: ESMT NAND 128MiB 3,3V 8-bit
[ 2.626855] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 2.634399] Scanning device for bad blocks
[ 2.784501] 10 ofpart partitions found on MTD device MT7621-NAND
[ 2.790493] Creating 10 MTD partitions on "MT7621-NAND":
[ 2.795810] 0x000000000000-0x000000080000 : "Bootloader"
[ 2.802545] 0x000000080000-0x0000000c0000 : "Config"
[ 2.808805] 0x0000000c0000-0x000000100000 : "Bdata"
[ 2.814961] 0x000000100000-0x000000140000 : "Factory"
[ 2.821369] 0x000000140000-0x000000180000 : "crash"
[ 2.827570] 0x000000180000-0x0000001c0000 : "crash_syslog"
[ 2.834259] 0x0000001c0000-0x000000200000 : "reserved0"
[ 2.840866] 0x000000200000-0x000000600000 : "kernel_stock"
[ 2.847705] 0x000000600000-0x000000a00000 : "kernel"
[ 2.853942] 0x000000a00000-0x000007f80000 : "ubi"
[ 2.860898] [mtk_nand] probe successfully!
[ 2.865771] Signature matched and data read!
[ 2.870021] load_fact_bbt success 1023
[ 2.874429] libphy: Fixed MDIO Bus: probed
[ 2.947980] libphy: mdio: probed
[ 4.350751] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver
[ 4.357511] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 20
[ 4.368063] NET: Registered protocol family 10
[ 4.374121] NET: Registered protocol family 17
[ 4.378695] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 4.391609] 8021q: 802.1Q VLAN Support v1.8
[ 4.398759] UBI: auto-attach mtd9
[ 4.402087] ubi0: attaching mtd9
[ 4.618462] mtk_soc_eth 1e100000.ethernet eth0: port 1 link up
[ 5.521109] ubi0: scanning is finished
[ 5.541359] ubi0: attached mtd9 (name "ubi", size 117 MiB)
[ 5.546892] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 5.553734] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 5.560504] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 5.567456] ubi0: good PEBs: 940, bad PEBs: 0, corrupted PEBs: 0
[ 5.573433] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 5.580638] ubi0: max/mean erase counter: 13/8, WL threshold: 4096, image sequence number: 2038926528
[ 5.589837] ubi0: available PEBs: 0, total reserved PEBs: 940, PEBs reserved for bad PEB handling: 20
[ 5.599059] ubi0: background thread "ubi_bgt0d" started, PID 375
[ 5.601341] block ubiblock0_0: created from ubi0:0(rootfs)
[ 5.601351] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 5.601368] hctosys: unable to open rtc device (rtc0)
[ 5.628756] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 5.636357] Freeing unused kernel memory: 204K
[ 5.640789] This architecture does not have kernel memory protection.
[ 6.074383] init: Console is alive
[ 6.078103] init: - watchdog -
[ 6.598228] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.689821] usbcore: registered new interface driver usbfs
[ 6.695512] usbcore: registered new interface driver hub
[ 6.700979] usbcore: registered new device driver usb
[ 6.715182] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 6.720568] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[ 6.735589] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x00210010
[ 6.744061] xhci-mtk 1e1c0000.xhci: irq 19, io mem 0x1e1c0000
[ 6.750901] hub 1-0:1.0: USB hub found
[ 6.754722] hub 1-0:1.0: 2 ports detected
[ 6.759206] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 6.764511] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[ 6.772203] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 6.781167] hub 2-0:1.0: USB hub found
[ 6.784977] hub 2-0:1.0: 1 port detected
[ 6.791578] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.815674] init: - preinit -
[ 7.225713] usb 2-1: new SuperSpeed USB device number 2 using xhci-mtk
[ 7.959769] mtk_soc_eth 1e100000.ethernet eth0: port 2 link up
[ 10.669578] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 466
[ 10.743280] UBIFS (ubi0:1): recovery needed
[ 11.027687] UBIFS (ubi0:1): recovery completed
[ 11.032307] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 11.040127] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 11.050019] UBIFS (ubi0:1): FS size: 112754688 bytes (107 MiB, 888 LEBs), journal size 5586944 bytes (5 MiB, 44 LEBs)
[ 11.060604] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
[ 11.067215] UBIFS (ubi0:1): media format: w4/r0 (latest is w4/r0), UUID 20B5BE78-6BF9-4D9C-97D0-63EEEE29FCD2, small LPT model
[ 11.089886] mount_root: overlay filesystem has not been fully initialized yet
[ 11.099816] mount_root: switching to ubifs overlay
[ 11.120963] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 11.206878] procd: - early -
[ 11.209848] procd: - watchdog -
[ 11.915518] procd: - watchdog -
[ 11.918952] procd: - ubus -
[ 11.977423] procd: - init -
[ 12.220332] kmodloader: loading kernel modules from /etc/modules.d/*
[ 12.230433] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.243720] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[ 12.251747] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[ 12.260419] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.272071] nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
[ 12.311093] xt_time: kernel timezone is -0000
[ 12.364278] mt7603e 0000:01:00.0: ASIC revision: 76030010
[ 12.395013] mt7603e 0000:01:00.0: Firmware Version: ap_pcie
[ 12.400808] mt7603e 0000:01:00.0: Build Time: 20160107100755
[ 12.445412] firmware init done
[ 12.617059] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 12.624541] mt76x2e 0000:02:00.0: ASIC revision: 76120044
[ 12.655444] mt76x2e 0000:02:00.0: ROM patch already applied
[ 12.662251] mt76x2e 0000:02:00.0: Firmware Version: 0.0.00
[ 12.667798] mt76x2e 0000:02:00.0: Build: 1
[ 12.671877] mt76x2e 0000:02:00.0: Build Time: 201507311614____
[ 12.705439] mt76x2e 0000:02:00.0: Firmware running!
[ 12.711683] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 12.719726] PPP generic driver version 2.4.2
[ 12.725836] NET: Registered protocol family 24
[ 12.733132] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 19.603555] device eth0 entered promiscuous mode
[ 19.610919] br-lan: port 1(eth0.1) entered blocking state
[ 19.616476] br-lan: port 1(eth0.1) entered disabled state
[ 19.622586] device eth0.1 entered promiscuous mode
[ 19.634503] br-lan: port 1(eth0.1) entered blocking state
[ 19.639985] br-lan: port 1(eth0.1) entered forwarding state
[ 19.646017] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 20.605960] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 22.159899] random: crng init done
[ 191.009312] Data buffer not 16 bytes aligned: 8e40c028
[ 191.017026] Data buffer not 16 bytes aligned: 8e40c508
[ 191.025523] Data buffer not 16 bytes aligned: 8e40c238
[ 191.034117] Data buffer not 16 bytes aligned: 8e40c198
[ 191.052419] Data buffer not 16 bytes aligned: 8e40c4f8
[ 191.066409] Data buffer not 16 bytes aligned: 8e40c278
[ 191.081738] Data buffer not 16 bytes aligned: 8e40c1c8
[ 191.096954] Data buffer not 16 bytes aligned: 8e40c088
[ 191.111147] Data buffer not 16 bytes aligned: 8e40c028
[ 191.139460] Data buffer not 16 bytes aligned: 8e40c018
[ 191.161243] Data buffer not 16 bytes aligned: 8e40c028
[ 191.176451] Data buffer not 16 bytes aligned: 8e40c128
[ 191.193724] Data buffer not 16 bytes aligned: 8e40c018
[ 191.213324] Data buffer not 16 bytes aligned: 8e40c078
[ 191.225880] Data buffer not 16 bytes aligned: 8e40c2a8
[ 191.265755] Data buffer not 16 bytes aligned: 8e40c158
[ 191.278589] Data buffer not 16 bytes aligned: 8e40c138
[ 191.289159] Data buffer not 16 bytes aligned: 8e40c248
[ 191.317077] Data buffer not 16 bytes aligned: 8e40c278
[ 191.334425] Data buffer not 16 bytes aligned: 8e40c0e8
[ 191.350534] Data buffer not 16 bytes aligned: 8e40c0f8
[ 283.715442] kmodloader: loading kernel modules from /etc/modules.d/*
[ 283.733985] SCSI subsystem initialized
[ 283.745511] usbcore: registered new interface driver usb-storage
[ 283.751874] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 283.816960] kmodloader: loading kernel modules from /etc/modules.d/*
[ 283.825496] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 313.727224] Data buffer not 16 bytes aligned: 8ee38068
[ 313.741091] Data buffer not 16 bytes aligned: 8ee38128
[ 313.749533] Data buffer not 16 bytes aligned: 8ee38078
[ 313.756765] Data buffer not 16 bytes aligned: 8ee383d8
[ 313.785037] Data buffer not 16 bytes aligned: 8ee38128
[ 313.795667] Data buffer not 16 bytes aligned: 8ee38258
[ 313.805290] Data buffer not 16 bytes aligned: 8ee38418
[ 313.813705] Data buffer not 16 bytes aligned: 8ee381a8
[ 313.822188] Data buffer not 16 bytes aligned: 8ee380d8
[ 313.840545] Data buffer not 16 bytes aligned: 8ee38438
[ 313.848969] Data buffer not 16 bytes aligned: 8ee382d8
[ 434.295326] kmodloader: loading kernel modules from /etc/modules.d/*
[ 434.305009] usbcore: registered new interface driver ums-alauda
[ 434.312020] usbcore: registered new interface driver ums-cypress
[ 434.319060] usbcore: registered new interface driver ums-datafab
[ 434.326131] usbcore: registered new interface driver ums-freecom
[ 434.333240] usbcore: registered new interface driver ums-isd200
[ 434.340310] usbcore: registered new interface driver ums-jumpshot
[ 434.347438] usbcore: registered new interface driver ums-karma
[ 434.354646] usbcore: registered new interface driver ums-sddr09
[ 434.361748] usbcore: registered new interface driver ums-sddr55
[ 434.368806] usbcore: registered new interface driver ums-usbat
[ 434.374965] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 457.162257] kmodloader: loading kernel modules from /etc/modules.d/*
[ 457.174784] scsi host0: uas
[ 457.178931] xhci-mtk 1e1c0000.xhci: ERROR Transfer event for disabled endpoint or incorrect stream ring
[ 457.188303] xhci-mtk 1e1c0000.xhci: @000000000fded170 0ee20000 00000000 05000000 01058001
[ 457.196514] xhci-mtk 1e1c0000.xhci: ERROR Transfer event for disabled endpoint or incorrect stream ring
[ 457.205879] xhci-mtk 1e1c0000.xhci: @000000000fded180 0ee20100 00000000 05000000 01078001
[ 464.441727] Data buffer not 16 bytes aligned: 8ee2c458
[ 464.469820] Data buffer not 16 bytes aligned: 8ee2c0d8
[ 464.477079] Data buffer not 16 bytes aligned: 8ee2c368
[ 477.979944] scsi 0:0:0:0: tag#0 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD IN
[ 477.987509] scsi 0:0:0:0: tag#0 CDB: opcode=0x12 12 00 00 00 24 00
[ 479.029938] scsi host0: uas_eh_bus_reset_handler FAILED to get lock err -16
[ 479.036896] scsi 0:0:0:0: Device offlined - not ready after error recovery
[ 479.044393] usbcore: registered new interface driver uas
[ 479.050016] kmodloader: done loading kernel modules from /etc/modules.d/*
More information can be found at the following URL:
https://bugs.lede-project.org/index.php?do=details&task_id=1305
More information about the lede-bugs
mailing list