[FS#1199] Bad Header Checksum DIR-600 B5E
LEDE Bugs
lede-bugs at lists.infradead.org
Sat Jan 6 06:32:21 PST 2018
The following task has a new comment added:
FS#1199 - Bad Header Checksum DIR-600 B5E
User who did this - Venca B Spam (vbspam)
----------
Sorry for spamming with long logs. Here is full record of:
- Failed boot "Wrong checksum"
- Flashing of
- First boot after flash, which is OK
- Failed boot "Wrong checksum" after reboot.
dcache: sets:128, ways:4, linesz:32 ,total:16384
## Powering down port 0 ~ 3.
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
A: Load Runtime code then write to Flash via Serial.
\0x08\0x08\0x08 0
3: System Boot system code via Flash.
## Booting image at bc050000 ...
......................................................addr:80400000
We have SEAMA, Image Size = 3428292
Verifying Checksum ...
Bad Header Checksum.
## Powering up port 0 ~ 3.
Entering HTTP server.
KSEG1ADDR(NetTxPacket) = 0xA1FE74C0
NetLoop,call eth_halt !
NetLoop,call eth_init !
Waitting for RX_DMA_BUSY status Start... done
Header Payload scatter function is Disable !!
ETH_STATE_ACTIVE!!
Using Eth0 (10/100-M) device
Start HTTP server on port 80, 192.168.0.1
Running ...
Got ARP REQUEST, return our IP
mpfd_decode: UPLOADED, upsize = 3301428
SEAMA ==========================================
magic : 5ea3a417
meta size : 36 bytes
meta data : signature=wrgn59_dlob.hans_dir610
meta data :
meta data :
image size : 0 bytes
================================================
SEAMA ==========================================
magic : 5ea3a417
meta size : 36 bytes
meta data : dev=/dev/mtdblock/2
meta data : type=firmware
meta data :
meta data :
image size : 3301316 bytes
checksum : 701AAA72BB6EA38245ABA6D912984CB9
digest : 701AAA72BB6EA38245ABA6D912984CB9
Selected !!!
================================================
Copy SEAMA with header (from 0x80100030).
raspi_erase_write: offs:50000, count:326004
raspi_erase: offs:50000 len:320000
..................................................
raspi_write: to:50000 len:320000
..................................................
...................................................raspi_erase: offs:370000 len:10000
.
raspi_write: to:370000 len:10000
.
.Done!
Copy linux image [3301380 bytes] to Flash offset [0x00050000] ...
U-Boot 1.1.3 (Feb 25 2011 - 14:31:26) (ALPHA)
SVN revision: 499
Target board: WRG-N49
Board: Ralink APSoC DRAM: 32 MB
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 42
spi device id: c2 20 16 c2 20 (2016c220)
find flash: MX25L3205D
..============================================
Ralink UBoot Version: 3.5.1.0
--------------------------------------------
ASIC 5350_MP (Port5None)
DRAM_CONF_FROM: Boot-Strapping
DRAM_TYPE: SDRAM
DRAM_SIZE: 256 Mbits
DRAM_WIDTH: 16 bits
DRAM_TOTAL_WIDTH: 16 bits
TOTAL_MEMORY_SIZE: 32 MBytes
Flash component: SPI Flash
Date:Feb 25 2011 Time:14:31:26
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384
## Powering down port 0 ~ 3.
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
A: Load Runtime code then write to Flash via Serial.
\0x08\0x08\0x08 0
3: System Boot system code via Flash.
## Booting image at bc050000 ...
....................................................addr:80400000
We have SEAMA, Image Size = 3301316
Verifying Checksum ...
Uncompressing SEAMA linux.lzma ... OK
## Transferring control to Linux (at address ff000000) ...
## Giving linux memsize in MB, 32
Starting kernel ...
[ 0.000000] Linux version 4.4.92 (buildbot at debian8) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3556-46e29bd) ) #0 Mon Oct 16 15:21:43 2017
[ 0.000000] SoC Type: Ralink RT5350 id:1 rev:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001964c (MIPS 24KEc)
[ 0.000000] MIPS: machine is D-Link DIR-610 A1
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=00048000
[ 0.000000] Readback ErrCtl register=00048000
[ 0.000000] Memory: 28612K/32768K available (2892K kernel code, 132K rwdata, 356K rodata, 196K init, 196K bss, 4156K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 360MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 10618113593 ns
[ 0.000016] sched_clock: 32 bits at 180MHz, resolution 5ns, wraps every 11930464253ns
[ 0.015683] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080)
[ 0.090902] pid_max: default: 32768 minimum: 301
[ 0.100366] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.113457] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.136707] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.156289] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.168498] pinctrl core: initialized pinctrl subsystem
[ 0.181412] NET: Registered protocol family 16
[ 0.199495] Can't analyze schedule() prologue at 8000acdc
[ 0.240941] rt2880_gpio 10000600.gpio: registering 22 gpios
[ 0.252067] rt2880_gpio 10000600.gpio: registering 22 irq handlers
[ 0.267010] clocksource: Switched to clocksource MIPS
[ 0.279311] NET: Registered protocol family 2
[ 0.289992] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.303888] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.316478] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.329345] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.340983] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.353913] NET: Registered protocol family 1
[ 0.372829] rt-timer 10000100.timer: maximum frequency is 3662Hz
[ 0.386400] Crashlog allocated RAM at address 0x1f00000
[ 0.433609] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.445202] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.470958] io scheduler noop registered
[ 0.478741] io scheduler deadline registered (default)
[ 0.489307] ralink-usb-phy usbphy: invalid resource
[ 0.500155] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.519757] console [ttyS0] disabled
[ 0.526804] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.546636] console [ttyS0] enabled
[ 0.546636] console [ttyS0] enabled
[ 0.560420] bootconsole [early0] disabled
[ 0.560420] bootconsole [early0] disabled
[ 0.591950] spi spi0.0: force spi mode3
[ 0.600611] m25p80 spi0.0: mx25l3205d (4096 Kbytes)
[ 0.610543] 4 ofpart partitions found on MTD device spi0.0
[ 0.621546] Creating 4 MTD partitions on "spi0.0":
[ 0.631174] 0x000000000000-0x000000030000 : "u-boot"
[ 0.644858] 0x000000030000-0x000000040000 : "devdata"
[ 0.659188] 0x000000040000-0x000000050000 : "factory"
[ 0.673315] 0x000000050000-0x000000400000 : "firmware"
[ 1.127591] 2 seama-fw partitions found on MTD device firmware
[ 1.139334] 0x000000050040-0x00000016c000 : "kernel"
[ 1.152581] 0x00000016c000-0x000000400000 : "rootfs"
[ 1.166403] mtd: device 5 (rootfs) set to be root filesystem
[ 1.178021] 1 squashfs-split partitions found on MTD device rootfs
[ 1.190451] 0x000000376000-0x000000400000 : "rootfs_data"
[ 1.211013] rt3050-esw 10110000.esw: link changed 0x00
[ 1.224876] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 1.242588] rt2880_wdt 10000120.watchdog: Initialized
[ 1.255304] NET: Registered protocol family 10
[ 1.272058] NET: Registered protocol family 17
[ 1.281267] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.306519] 8021q: 802.1Q VLAN Support v1.8
[ 1.331527] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 1.347917] Freeing unused kernel memory: 196K
[ 3.700198] init: Console is alive
[ 3.707828] init: - watchdog -
[ 5.262226] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.408062] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.433488] init: - preinit -
[ 6.822970] rt3050-esw 10110000.esw: link changed 0x00
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug[ 7.137305] random: procd: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
level
[ 8.627306] rt3050-esw 10110000.esw: link changed 0x04
[ 10.373409] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 10.395511] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 10.591095] procd: - early -
[ 10.597287] procd: - watchdog -
[ 11.256728] procd: - watchdog -
[ 11.263940] procd: - ubus -
[ 11.516950] random: ubusd: uninitialized urandom read (4 bytes read, 18 bits of entropy available)
[ 11.656834] random: ubusd: uninitialized urandom read (4 bytes read, 18 bits of entropy available)
[ 11.675949] random: ubusd: uninitialized urandom read (4 bytes read, 18 bits of entropy available)
[ 11.694269] random: ubusd: uninitialized urandom read (4 bytes read, 18 bits of entropy available)
[ 11.713353] random: ubusd: uninitialized urandom read (4 bytes read, 18 bits of entropy available)
[ 11.731618] random: ubusd: uninitialized urandom read (4 bytes read, 18 bits of entropy available)
[ 11.750348] random: ubusd: uninitialized urandom read (4 bytes read, 18 bits of entropy available)
[ 11.769095] random: ubusd: uninitialized urandom read (4 bytes read, 18 bits of entropy available)
[ 11.788314] procd: - init -
Please press Enter to activate this console.
[ 12.321996] kmodloader: loading kernel modules from /etc/modules.d/*
[ 12.346209] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.381539] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[ 12.397672] Backport generated by backports.git backports-20160324-13-g24da7d3c
[ 12.420515] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.446430] nf_conntrack version 0.5.0 (450 buckets, 1800 max)
[ 12.524180] xt_time: kernel timezone is -0000
[ 12.634360] PPP generic driver version 2.4.2
[ 12.648465] NET: Registered protocol family 24
[ 12.705048] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "devdata"
[ 12.719654] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5350, rev 0500 detected
[ 12.735202] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5350 detected
[ 12.892533] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 14.551274] random: jshn: uninitialized urandom read (4 bytes read, 23 bits of entropy available)
[ 20.958486] rt3050-esw 10110000.esw: link changed 0x00
[ 22.777621] rt3050-esw 10110000.esw: link changed 0x04
[ 25.618151] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 25.647226] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 25.660531] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 32.315780] device eth0.1 entered promiscuous mode
[ 32.326181] device eth0 entered promiscuous mode
[ 32.436647] br-lan: port 1(eth0.1) entered forwarding state
[ 32.447998] br-lan: port 1(eth0.1) entered forwarding state
[ 34.447340] br-lan: port 1(eth0.1) entered forwarding state
[ 34.977379] done.
[ 34.981298] jffs2: notice: (816) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 76.657098] random: nonblocking pool is initialized
[ 88.970627] br-lan: port 1(eth0.1) entered disabled state
[ 89.007267] device eth0.1 left promiscuous mode
[ 89.016614] br-lan: port 1(eth0.1) entered disabled state
[ 89.043588] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 89.485980] device eth0 left promiscuous mode
[ 93.788454] reboot: Restarting system
U-Boot 1.1.3 (Feb 25 2011 - 14:31:26) (ALPHA)
SVN revision: 499
Target board: WRG-N49
Board: Ralink APSoC DRAM: 32 MB
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 42
spi device id: c2 20 16 c2 20 (2016c220)
find flash: MX25L3205D
..============================================
Ralink UBoot Version: 3.5.1.0
--------------------------------------------
ASIC 5350_MP (Port5None)
DRAM_CONF_FROM: Boot-Strapping
DRAM_TYPE: SDRAM
DRAM_SIZE: 256 Mbits
DRAM_WIDTH: 16 bits
DRAM_TOTAL_WIDTH: 16 bits
TOTAL_MEMORY_SIZE: 32 MBytes
Flash component: SPI Flash
Date:Feb 25 2011 Time:14:31:26
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384
## Powering down port 0 ~ 3.
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
A: Load Runtime code then write to Flash via Serial.
\0x08\0x08\0x08 0
3: System Boot system code via Flash.
## Booting image at bc050000 ...
....................................................addr:80400000
We have SEAMA, Image Size = 3301316
Verifying Checksum ...
Bad Header Checksum.
## Powering up port 0 ~ 3.
Entering HTTP server.
KSEG1ADDR(NetTxPacket) = 0xA1FE74C0
NetLoop,call eth_halt !
NetLoop,call eth_init !
Waitting for RX_DMA_BUSY status Start... done
Header Payload scatter function is Disable !!
ETH_STATE_ACTIVE!!
Using Eth0 (10/100-M) device
Start HTTP server on port 80, 192.168.0.1
Running ...
----------
More information can be found at the following URL:
https://bugs.lede-project.org/index.php?do=details&task_id=1199#comment4077
More information about the lede-bugs
mailing list