[FS#1503] GL-MT300A Crashes and Reboots in a Loop As of 17.01.2
LEDE Bugs
lede-bugs at lists.infradead.org
Fri Apr 20 20:53:46 PDT 2018
The following task has a new comment added:
FS#1503 - GL-MT300A Crashes and Reboots in a Loop As of 17.01.2
User who did this - languagegame (languagegame)
----------
I connected a serial cable and captured the log. This is for LEDE 17.01.4. Only change to default configuration was to enable Wi-Fi. No ethernet cables plugged in. Just the serial cable and the power cable. I'll try snapshot to see if fails there as well. Note that it crashes when I connected via Wi-Fi and open Luci. It doesn't crash under LEDE 17.01.1. After it reboots, I checked to see if there was a crashlog under /sys/kernel/debug, but I did not see anything.
Anyway, here is the serial log (you can see it rebooted twice, I pulled the power cord after the second reboot so the log gets cut off at the end).
U-Boot 1.1.3 (Dec 23 2015 - 18:37:46)
Board: Ralink APSoC DRAM: 128 MB
relocate_code Pointer2 at: 87fac000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: ef 40 18 0 0 (40180000)
find flash: W25Q128FV
*** Warning - bad CRC, using default environment
======================================================
uboot-gl-mt7620 version: 0.0.0.1
--------------------------------------------------
ASIC 7620_MP (Port5None)
DRAM component: 1024 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 128 MBytes
Flash component: SPI Flash
Date:Dec 23 2015 Time:18:37:46
--------------------------------------------------
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
--------------------------------------------------
##### The CPU freq = 580 MHZ ####
##### Memory size =128 Mbytes ####
======================================================
Press press WPS button for more than 2 seconds to run web failsafe mode
WPS button is pressed for: 0 second(s)
Catution: WPS button wasn't pressed or not long enough!
Continuing normal boot...
*** *** ** ** ***** *** *** *** *
* * * ** ** * * * * * * * * * *
* * ** ** * * * * * * **
* * ***** ** ** * ** * * * * * *
* *** * * * * * * * * * * * *
* * * * * * * * * * * * ****
* * * * * * * * * * * * * * * *
** ****** * * * *** *** *** *** ** **
Hit SPACE to stop autoboot: 0
Found calibration data, checking calibration status...
Device calibrated. Checking MAC address...
Found MAC. Starting firmware...
## Booting image at bc050000 ...
Image Name: MIPS LEDE Linux-4.4.92
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1214310 Bytes = 1.2 MB
Load Address: 80000000
Entry Point: 80000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 128
Starting kernel ...
[ 0.000000] Linux version 4.4.92 (buildbot at debian8) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3557-a5e1f7f) ) #0 Mon Oct 16 22:57:05 2017
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is GL-MT300A
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00004caa
[ 0.000000] Readback ErrCtl register=00004caa
[ 0.000000] Memory: 125924K/131072K available (3017K kernel code, 147K rwdata, 384K rodata, 156K init, 208K bss, 5148K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000012] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.007577] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.070070] pid_max: default: 32768 minimum: 301
[ 0.074698] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.081069] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.094517] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.104064] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.110019] pinctrl core: initialized pinctrl subsystem
[ 0.116367] NET: Registered protocol family 16
[ 0.126099] Can't analyze schedule() prologue at 8000acdc
[ 0.144857] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.150302] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.156454] rt2880_gpio 10000638.gpio: registering 16 gpios
[ 0.161853] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[ 0.167970] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.173370] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.179490] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.184803] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.192118] clocksource: Switched to clocksource systick
[ 0.198529] NET: Registered protocol family 2
[ 0.203796] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.210520] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.216746] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.222972] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.228598] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.234961] NET: Registered protocol family 1
[ 0.243493] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.250136] Crashlog allocated RAM at address 0x3f00000
[ 0.271590] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.277259] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.289391] io scheduler noop registered
[ 0.293198] io scheduler deadline registered (default)
[ 0.298370] ralink-usb-phy usbphy: invalid resource
[ 0.303696] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.313517] console [ttyS0] disabled
[ 0.316968] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.326642] console [ttyS0] enabled
[ 0.326642] console [ttyS0] enabled
[ 0.333673] bootconsole [early0] disabled
[ 0.333673] bootconsole [early0] disabled
[ 0.348487] spi spi0.0: force spi mode3
[ 0.353031] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.357877] 5 ofpart partitions found on MTD device spi0.0
[ 0.363522] Creating 5 MTD partitions on "spi0.0":
[ 0.368417] 0x000000000000-0x000000030000 : "u-boot"
[ 0.375322] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.382650] 0x000000040000-0x000000050000 : "factory"
[ 0.389602] 0x000000050000-0x000000fd0000 : "firmware"
[ 1.702350] 2 uimage-fw partitions found on MTD device firmware
[ 1.708416] 0x000000050000-0x0000001787a6 : "kernel"
[ 1.715127] 0x0000001787a6-0x000000fd0000 : "rootfs"
[ 1.721983] mtd: device 5 (rootfs) set to be root filesystem
[ 1.727975] 1 squashfs-split partitions found on MTD device rootfs
[ 1.734311] 0x0000003c0000-0x000000fd0000 : "rootfs_data"
[ 1.741674] 0x000000ff0000-0x000001000000 : "art"
[ 1.749394] rt2880-pinmux pinctrl: pin io40 already requested by pinctrl; cannot claim for 10100000.ethernet
[ 1.759513] rt2880-pinmux pinctrl: pin-40 (10100000.ethernet) status -22
[ 1.766371] rt2880-pinmux pinctrl: could not request pin 40 (io40) from group ephy on device rt2880-pinmux
[ 1.776325] mtk_soc_eth 10100000.ethernet: Error applying setting, reverse things back
[ 1.787286] gsw: setting port4 to ephy mode
[ 1.791795] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 1.798689] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 1.807714] rt2880_wdt 10000120.watchdog: Initialized
[ 1.814393] NET: Registered protocol family 10
[ 1.822375] NET: Registered protocol family 17
[ 1.827000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.839906] 8021q: 802.1Q VLAN Support v1.8
[ 1.858792] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 1.866909] Freeing unused kernel memory: 156K
[ 3.971266] init: Console is alive
[ 3.975106] init: - watchdog -
[ 5.946051] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.043422] usbcore: registered new interface driver usbfs
[ 6.049132] usbcore: registered new interface driver hub
[ 6.054734] usbcore: registered new device driver usb
[ 6.065385] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.073579] ehci-platform: EHCI generic platform driver
[ 6.089307] phy phy-usbphy.0: remote usb device wakeup disabled
[ 6.095374] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 6.099944] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 6.105863] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 6.114075] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 6.124628] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 6.132119] hub 1-0:1.0: USB hub found
[ 6.136450] hub 1-0:1.0: 1 port detected
[ 6.143202] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.150950] ohci-platform: OHCI generic platform driver
[ 6.156643] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 6.163629] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 6.171820] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 6.202535] hub 2-0:1.0: USB hub found
[ 6.206729] hub 2-0:1.0: 1 port detected
[ 6.214284] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.225899] init: - preinit -
[ 6.946075] 8021q: adding VLAN 0 to HW filter on device eth0
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 9.767604] jffs2: notice: (359) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 9.786423] mount_root: switching to jffs2 overlay
[ 9.802881] urandom-seed: Seeding with /etc/urandom.seed
[ 10.065338] procd: - early -
[ 10.068999] procd: - watchdog -
[ 10.497990] procd: - watchdog -
[ 10.501537] procd: - ubus -
[ 10.716176] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 10.727568] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 10.737337] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 10.746658] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 10.760173] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 10.769481] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 10.778877] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 10.788279] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 10.797941] procd: - init -
Please press Enter to activate this console.
[ 11.156858] kmodloader: loading kernel modules from /etc/modules.d/*
[ 11.169397] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 11.185212] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[ 11.193458] Backport generated by backports.git backports-20160324-13-g24da7d3c
[ 11.256873] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.271766] nf_conntrack version 0.5.0 (1970 buckets, 7880 max)
[ 11.322991] xt_time: kernel timezone is -0000
[ 11.339497] PPP generic driver version 2.4.2
[ 11.346810] NET: Registered protocol family 24
[ 11.368726] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
[ 11.376191] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[ 11.384126] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[ 11.494971] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 12.403315] random: jshn: uninitialized urandom read (4 bytes read, 24 bits of entropy available)
[ 12.501821] random: ubusd: uninitialized urandom read (4 bytes read, 24 bits of entropy available)
[ 18.754599] 8021q: adding VLAN 0 to HW filter on device eth0
[ 18.775788] device eth0.1 entered promiscuous mode
[ 18.780699] device eth0 entered promiscuous mode
[ 18.796474] br-lan: port 1(eth0.1) entered forwarding state
[ 18.802278] br-lan: port 1(eth0.1) entered forwarding state
[ 20.800942] br-lan: port 1(eth0.1) entered forwarding state
[ 22.502810] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 22.529863] device wlan0 entered promiscuous mode
[ 23.047697] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 23.054417] br-lan: port 2(wlan0) entered forwarding state
[ 23.060074] br-lan: port 2(wlan0) entered forwarding state
[ 23.820273] br-lan: port 2(wlan0) entered forwarding state
[ 33.759203] random: nonblocking pool is initialized
U-Boot 1.1.3 (Dec 23 2015 - 18:37:46)
Board: Ralink APSoC DRAM: 128 MB
relocate_code Pointer2 at: 87fac000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: ef 40 18 0 0 (40180000)
find flash: W25Q128FV
*** Warning - bad CRC, using default environment
======================================================
uboot-gl-mt7620 version: 0.0.0.1
--------------------------------------------------
ASIC 7620_MP (Port5None)
DRAM component: 1024 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 128 MBytes
Flash component: SPI Flash
Date:Dec 23 2015 Time:18:37:46
--------------------------------------------------
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
--------------------------------------------------
##### The CPU freq = 580 MHZ ####
##### Memory size =128 Mbytes ####
======================================================
Press press WPS button for more than 2 seconds to run web failsafe mode
WPS button is pressed for: 0 second(s)
Catution: WPS button wasn't pressed or not long enough!
Continuing normal boot...
*** *** ** ** ***** *** *** *** *
* * * ** ** * * * * * * * * * *
* * ** ** * * * * * * **
* * ***** ** ** * ** * * * * * *
* *** * * * * * * * * * * * *
* * * * * * * * * * * * ****
* * * * * * * * * * * * * * * *
** ****** * * * *** *** *** *** ** **
Hit SPACE to stop autoboot: 0
Found calibration data, checking calibration status...
Device calibrated. Checking MAC address...
Found MAC. Starting firmware...
## Booting image at bc050000 ...
Image Name: MIPS LEDE Linux-4.4.92
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1214310 Bytes = 1.2 MB
Load Address: 80000000
Entry Point: 80000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 128
Starting kernel ...
[ 0.000000] Linux version 4.4.92 (buildbot at debian8) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3557-a5e1f7f) ) #0 Mon Oct 16 22:57:05 2017
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is GL-MT300A
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00004ca1
[ 0.000000] Readback ErrCtl register=00004ca1
[ 0.000000] Memory: 125924K/131072K available (3017K kernel code, 147K rwdata, 384K rodata, 156K init, 208K bss, 5148K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000012] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.007577] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.070070] pid_max: default: 32768 minimum: 301
[ 0.074698] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.081069] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.094518] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.104065] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.110019] pinctrl core: initialized pinctrl subsystem
[ 0.116367] NET: Registered protocol family 16
[ 0.126099] Can't analyze schedule() prologue at 8000acdc
[ 0.144856] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.150303] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.156454] rt2880_gpio 10000638.gpio: registering 16 gpios
[ 0.161853] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[ 0.167970] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.173370] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.179490] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.184802] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.192117] clocksource: Switched to clocksource systick
[ 0.198528] NET: Registered protocol family 2
[ 0.203796] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.210521] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.216747] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.222972] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.228599] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.234961] NET: Registered protocol family 1
[ 0.243494] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.250137] Crashlog allocated RAM at address 0x3f00000
[ 0.271591] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.277260] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.289391] io scheduler noop registered
[ 0.293199] io scheduler deadline registered (default)
[ 0.298370] ralink-usb-phy usbphy: invalid resource
[ 0.303697] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.313518] console [ttyS0] disabled
[ 0.316969] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.326644] console [ttyS0] enabled
[ 0.326644] console [ttyS0] enabled
[ 0.333674] bootconsole [early0] disabled
[ 0.333674] bootconsole [early0] disabled
[ 0.348488] spi spi0.0: force spi mode3
[ 0.353033] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.357878] 5 ofpart partitions found on MTD device spi0.0
[ 0.363523] Creating 5 MTD partitions on "spi0.0":
[ 0.368418] 0x000000000000-0x000000030000 : "u-boot"
[ 0.375322] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.382651] 0x000000040000-0x000000050000 : "factory"
[ 0.389602] 0x000000050000-0x000000fd0000 : "firmware"
[ 1.702357] 2 uimage-fw partitions found on MTD device firmware
[ 1.708424] 0x000000050000-0x0000001787a6 : "kernel"
[ 1.715134] 0x0000001787a6-0x000000fd0000 : "rootfs"
[ 1.721989] mtd: device 5 (rootfs) set to be root filesystem
[ 1.727981] 1 squashfs-split partitions found on MTD device rootfs
[ 1.734317] 0x0000003c0000-0x000000fd0000 : "rootfs_data"
[ 1.741680] 0x000000ff0000-0x000001000000 : "art"
[ 1.749401] rt2880-pinmux pinctrl: pin io40 already requested by pinctrl; cannot claim for 10100000.ethernet
[ 1.759520] rt2880-pinmux pinctrl: pin-40 (10100000.ethernet) status -22
[ 1.766378] rt2880-pinmux pinctrl: could not request pin 40 (io40) from group ephy on device rt2880-pinmux
[ 1.776332] mtk_soc_eth 10100000.ethernet: Error applying setting, reverse things back
[ 1.787290] gsw: setting port4 to ephy mode
[ 1.791799] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 1.798693] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 1.807719] rt2880_wdt 10000120.watchdog: Initialized
[ 1.814399] NET: Registered protocol family 10
[ 1.822382] NET: Registered protocol family 17
[ 1.827007] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.839912] 8021q: 802.1Q VLAN Support v1.8
[ 1.858797] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 1.866915] Freeing unused kernel memory: 156K
[ 3.971446] init: Console is alive
[ 3.975292] init: - watchdog -
[ 5.947566] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.044972] usbcore: registered new interface driver usbfs
[ 6.050683] usbcore: registered new interface driver hub
[ 6.056284] usbcore: registered new device driver usb
[ 6.066939] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.075131] ehci-platform: EHCI generic platform driver
[ 6.090859] phy phy-usbphy.0: remote usb device wakeup disabled
[ 6.096925] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 6.101495] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 6.107414] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 6.115627] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 6.125623] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 6.133166] hub 1-0:1.0: USB hub found
[ 6.137477] hub 1-0:1.0: 1 port detected
[ 6.144306] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.151976] ohci-platform: OHCI generic platform driver
[ 6.157674] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 6.164635] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 6.172835] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 6.203545] hub 2-0:1.0: USB hub found
[ 6.207736] hub 2-0:1.0: 1 port detected
[ 6.215377] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.226958] init: - preinit -
[ 6.946992] 8021q: adding VLAN 0 to HW filter on device eth0
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 9.767690] jffs2: notice: (359) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 9.786525] mount_root: switching to jffs2 overlay
[ 9.802915] urandom-seed: Seeding with /etc/urandom.seed
[ 10.064774] procd: - early -
[ 10.067822] procd: - watchdog -
[ 10.497018] procd: - watchdog -
[ 10.500513] procd: - ubus -
[ 10.715244] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 10.726640] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 10.736413] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 10.745735] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 10.758513] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 10.768397] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 10.778182] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 10.787633] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 10.797257] procd: - init -
Please press Enter to activate this console.
[ 11.155418] kmodloader: loading kernel modules from /etc/modules.d/*
[ 11.167908] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 11.183698] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[ 11.191944] Backport generated by backports.git backports-20160324-13-g24da7d3c
[ 11.255613] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.270166] nf_conntrack version 0.5.0 (1970 buckets, 7880 max)
[ 11.321090] xt_time: kernel timezone is -0000
[ 11.337980] PPP generic driver version 2.4.2
[ 11.345216] NET: Registered protocol family 24
[ 11.367206] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
[ 11.374673] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[ 11.382608] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[ 11.493631] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 12.399625] random: jshn: uninitialized urandom read (4 bytes read, 24 bits of entropy available)
[ 12.498038] random: ubusd: uninitialized urandom read (4 bytes read, 24 bits of entropy available)
[ 18.746598] 8021q: adding VLAN 0 to HW filter on device eth0
[ 18.766443] device eth0.1 entered promiscuous mode
[ 18.771353] device eth0 entered promiscuous mode
[ 18.788216] br-lan: port 1(eth0.1) entered forwarding state
[ 18.794020] br-lan: port 1(eth0.1) entered forwarding state
[ 20.791601] br-lan: port 1(eth0.1) entered forwarding state
[ 22.499411] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 22.526761] device wlan0 entered promiscuous mode
[ 23.044001] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 23.050677] br-lan: port 2(wlan0) entered forwarding state
[ 23.056390] br-lan: port 2(wlan0) entered forwarding state
U-Boot 1.1.3 (Dec 23 2015 - 18:37:46)
Board: Ralink APSoC DRAM: 128 MB
relocate_code Pointer2 at: 87fac000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: ef 40 18 0 0 (40180000)
find flash: W25Q128FV
*** Warning - bad CRC, using default environment
======================================================
uboot-gl-mt7620 version: 0.0.0.1
--------------------------------------------------
ASIC 7620_MP (Port5None)
DRAM component: 1024 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 128 MBytes
Flash component: SPI Flash
Date:Dec 23 2015 Time:18:37:46
--------------------------------------------------
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
--------------------------------------------------
##### The CPU freq = 580 MHZ ####
##### Memory size =128 Mbytes ####
======================================================
Press press WPS button for more than 2 seconds to run web failsafe mode
WPS button is pressed for: 0 second(s)
Catution: WPS button wasn't pressed or not long enough!
Continuing normal boot...
*** *** ** ** ***** *** *** *** *
* * * ** ** * * * * * * * * * *
* * ** ** * * * * * * **
* * ***** ** ** * ** * * * * * *
* *** * * * * * * * * * * * *
* * * * * * * * * * * * ****
* * * * * * * * * * * * * * * *
** ****** * * * *** *** *** *** ** **
Hit SPACE to stop autoboot: 0
Found calibration data, checking calibration status...
Device calibrated. Checking MAC address...
Found MAC. Starting firmware...
## Booting image at bc050000 ...
Image Name: MIPS LEDE Linux-4.4.92
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1214310 Bytes = 1.2 MB
Load Address: 80000000
Entry Point: 80000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 128
Starting kernel ...
[ 0.000000] Linux version 4.4.92 (buildbot at debian8) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3557-a5e1f7f) ) #0 Mon Oct 16 22:57:05 2017
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is GL-MT300A
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00004ca0
[ 0.000000] Readback ErrCtl register=00004ca0
[ 0.000000] Memory: 125924K/131072K available (3017K kernel code, 147K rwdata, 384K rodata, 156K init, 208K bss, 5148K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000012] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.007577] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.070069] pid_max: default: 32768 minimum: 301
[ 0.074697] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.081069] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.094518] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.104064] futex hash table entries: 256 (or[ 1.702349] 2 uimage-fw partitions found on MTD device firmware
[ 1.708416] 0x000000050000-0x0000001787a6 : "kernel"
[ 1.715127] 0x0000001787a6-0x000000fd0000 : "rootfs"
[ 1.721982] mtd: device 5 (rootfs) set to be root filesystem
[ 1.727975] 1 squashfs-split partitions found on MTD device rootfs
[ 1.734310] 0x0000003c0000-0x000000fd0000 : "rootfs_data"
[ 1.741673] 0x000000ff0000-0x000001000000 : "art"
[ 1.749394] rt2880-pinmux pinctrl: pin io40 already requested by pinctrl; cannot claim for 10100000.ethernet
[ 1.759513] rt2880-pinmux pinctrl: pin-40 (10100000.ethernet) status -22
[ 1.766371] rt2880-pinmux pinctrl: could not request pin 40 (io40) from group ephy on device rt2880-pinmux
[ 1.776325] mtk_soc_eth 10100000.ethernet: Error applying setting, reverse things back
[ 1.787285] gsw: setting port4 to ephy mode
[ 1.791793] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 1.798688] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 1.807714] rt2880_wdt 10000120.watchdog: Initialized
[ 1.814394] NET: Registered protocol family 10
[ 1.822378] NET: Registered protocol family 17
[ 1.827004] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.839909] 8021q: 802.1Q VLAN Support v1.8
[ 1.858795] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 1.866912] Freeing unused kernel memory: 156K
----------
More information can be found at the following URL:
https://bugs.openwrt.org/index.php?do=details&task_id=1503#comment4640
More information about the lede-bugs
mailing list