[FS#1198] RT-N10U no Wi-Fi
LEDE Bugs
lede-bugs at lists.infradead.org
Wed Nov 29 05:11:38 PST 2017
A new Flyspray task has been opened. Details are below.
User who did this - Pavel Ch. (PavelCh)
Attached to Project - LEDE Project
Summary - RT-N10U no Wi-Fi
Task Type - Bug Report
Category - Base system
Status - Unconfirmed
Assigned To -
Operating System - All
Severity - Low
Priority - Very Low
Reported Version - All
Due in Version - Undecided
Due Date - Undecided
Details - - RT-N10U B (black version)[[https://www.asus.com/ru/Networking/RTN10U_B/|RTN10U_B on Asus site]]
- Trunk, lede 17.01
- No Wi-Fi interface (BCM5356U Unsupported)
On "ASUS Oleg's based custom firmware" all working good. [[https://github.com/wl500g/wl500g|Link]]
DD-WRT working
Kernel log:
[ 0.000000] Linux version 4.4.92 (buildbot at builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3104-41de9a2) ) #
0 Tue Oct 17 17:46:20 2017
[ 0.000000] CPU0 revision is: 00019749 (MIPS 74Kc)
[ 0.000000] bcm47xx: Using bcma bus
[ 0.000000] bcma: bus0: Found chip with id 0x5357, rev 0x02 and package 0x08
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 8034e4c0, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 60940K/65536K available (2979K kernel code, 134K rwdata, 368K rodata, 156K init, 294K bss, 4596K reserved, 0K
cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:128
[ 0.000000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x26, class 0x0)
[ 0.000000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x1C, class 0x0)
[ 0.000000] bcma: bus0: Core 2 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x03, class 0x0)
[ 0.000000] bcma: bus0: Core 3 found: MIPS 74K (manuf 0x4A7, id 0x82C, rev 0x04, class 0x0)
[ 0.000000] bcma: bus0: Core 4 found: USB 2.0 Host (manuf 0x4BF, id 0x819, rev 0x05, class 0x0)
[ 0.000000] bcma: bus0: Core 5 found: DDR1/DDR2 Memory Controller (manuf 0x4BF, id 0x82E, rev 0x02, class 0x0)
[ 0.000000] bcma: bus0: Core 6 found: I2S (manuf 0x4BF, id 0x834, rev 0x02, class 0x0)
[ 0.000000] bcma: bus0: Core 7 found: Internal Memory (manuf 0x4BF, id 0x80E, rev 0x0B, class 0x0)
[ 0.000000] bcma: bus0: Found rev 9 PMU (capabilities 0x28A42A09)
[ 0.000000] bcma: bus0: Found serial flash
[ 0.000000] bcma: bus0: Found M25P64 serial flash (size: 8192KiB, blocksize: 0x10000, blocks: 128)
[ 0.000000] bcma: bus0: Early bus registered
[ 0.000000] MIPS: machine is Asus RT-N10U
[ 0.000000] bcm47xx: Setting up vectored interrupts
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11479041721 ns
[ 0.000018] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12897800188ns
[ 0.000098] Calibrating delay loop... 166.29 BogoMIPS (lpj=831488)
[ 0.070083] pid_max: default: 32768 minimum: 301
[ 0.070391] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.070427] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.075081] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.075141] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.076637] NET: Registered protocol family 16
[ 0.077856] Can't analyze schedule() prologue at 800077c8
[ 0.101281] clocksource: Switched to clocksource MIPS
[ 0.103867] NET: Registered protocol family 2
[ 0.105856] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.105931] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.105983] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.106185] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.106247] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.106783] NET: Registered protocol family 1
[ 0.106894] PCI: CLS 0 bytes, default 32
[ 0.382153] bcma: bus0: Using SPROM revision 8 provided by platform.
[ 0.382201] bcma: bus0: PMU resource config unknown or not needed for device 0x5357
[ 0.384226] bcma: bus0: Workarounds unknown or not needed for device 0x5357
[ 0.384250] bcma: bus0: Initializing MIPS core...
[ 0.384285] bcma: bus0: set_irq: core 0x0812, irq 3 => 3
[ 0.384315] bcma: bus0: set_irq: core 0x082d, irq 4 => 4
[ 0.384344] bcma: bus0: set_irq: core 0x0819, irq 5 => 5
[ 0.384372] bcma: bus0: set_irq: core 0x0800, irq 2 => 2
[ 0.384401] bcma: bus0: set_irq: core 0x0834, irq 2 => 2
[ 0.384421] bcma: bus0: IRQ reconfiguration done
[ 0.384441] bcma: core 0x0800, irq : 2(S)* 3 4 5 6 D I
[ 0.384504] bcma: core 0x0812, irq : 2(S) 3* 4 5 6 D I
[ 0.384559] bcma: core 0x082d, irq : 2(S) 3 4* 5 6 D I
[ 0.384613] bcma: core 0x082c, irq : 2(S) 3 4 5 6 D I*
[ 0.384669] bcma: core 0x0819, irq : 2(S) 3 4 5* 6 D I
[ 0.384725] bcma: core 0x082e, irq : 2(S) 3 4 5 6 D* I
[ 0.384779] bcma: core 0x0834, irq : 2(S)* 3 4 5 6 D I
[ 0.384833] bcma: core 0x080e, irq : 2(S) 3 4 5 6 D I*
[ 0.386716] bcma: bus0: Bus registered
[ 0.388368] Crashlog allocated RAM at address 0x3f00000
[ 0.426212] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.426250] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.432144] io scheduler noop registered
[ 0.432186] io scheduler deadline registered (default)
[ 0.432671] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.438933] console [ttyS0] disabled
[ 0.459240] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 2, base_baud = 1250000) is a U6_16550A
[ 0.885792] console [ttyS0] enabled
[ 0.975392] 6 bcm47xxpart partitions found on MTD device bcm47xxsflash
[ 0.982111] Creating 6 MTD partitions on "bcm47xxsflash":
[ 0.987632] 0x000000000000-0x000000020000 : "boot"
[ 0.997490] 0x000000020000-0x0000007f0000 : "firmware"
[ 1.006378] 0x0000007f0000-0x000000800000 : "nvram"
[ 1.015012] 0x00000002001c-0x00000002091c : "loader"
[ 1.023736] 0x00000002091c-0x000000146000 : "linux"
[ 1.032419] 0x000000146000-0x0000007f0000 : "rootfs"
[ 1.041028] mtd: device 5 (rootfs) set to be root filesystem
[ 1.046985] 1 squashfs-split partitions found on MTD device rootfs
[ 1.053352] 0x000000380000-0x0000007f0000 : "rootfs_data"
[ 1.066436] libphy: Fixed MDIO Bus: probed
[ 1.070886] bgmac_bcma bcma0:2: Found PHY addr: 30 (NOREGS)
[ 1.080843] libphy: bcma_mdio mii bus: probed
[ 1.085417] bgmac_bcma bcma0:2: Support for Roboswitch not implemented
[ 1.196928] b53_common: found switch: BCM5325, rev 4
[ 1.203660] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded
[ 1.210067] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds)
[ 1.220613] NET: Registered protocol family 10
[ 1.232526] NET: Registered protocol family 17
[ 1.237213] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you
need this.
[ 1.250136] 8021q: 802.1Q VLAN Support v1.8
[ 1.266334] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 1.274895] Freeing unused kernel memory: 156K
[ 3.582722] init: Console is alive
[ 3.586646] init: - watchdog -
[ 5.153481] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.336974] usbcore: registered new interface driver usbfs
[ 5.342889] usbcore: registered new interface driver hub
[ 5.348554] usbcore: registered new device driver usb
[ 5.364200] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.373559] ehci-platform: EHCI generic platform driver
[ 5.379063] ehci-platform ehci-platform.0: EHCI Host Controller
[ 5.385294] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[ 5.393788] ehci-platform ehci-platform.0: irq 5, io mem 0x18004000
[ 5.411356] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[ 5.419861] hub 1-0:1.0: USB hub found
[ 5.424645] hub 1-0:1.0: 2 ports detected
[ 5.434531] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.443339] ohci-platform: OHCI generic platform driver
[ 5.448847] ohci-platform ohci-platform.0: Generic Platform OHCI controller
[ 5.456137] ohci-platform ohci-platform.0: new USB bus registered, assigned bus number 2
[ 5.464646] ohci-platform ohci-platform.0: irq 5, io mem 0x18009000
[ 5.527552] hub 2-0:1.0: USB hub found
[ 5.532255] hub 2-0:1.0: 2 ports detected
[ 5.543476] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.561711] init: - preinit -
[ 6.252838] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 6.323678] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6.405507] random: procd: uninitialized urandom read (4 bytes read, 10 bits of entropy available)
[ 7.911452] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 11.645237] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 11.660347] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 12.032169] procd: - early -
[ 12.035360] procd: - watchdog -
[ 12.685531] procd: - watchdog -
[ 12.689549] procd: - ubus -
[ 12.895262] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 13.044907] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 13.055106] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 13.064454] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 13.074582] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 13.083914] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 13.093647] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 13.103370] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 13.113510] procd: - init -
[ 14.688338] kmodloader: loading kernel modules from /etc/modules.d/*
[ 14.703959] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 14.732965] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[ 14.741123] Backport generated by backports.git backports-20160324-13-g24da7d3c
[ 14.755412] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.778228] nf_conntrack version 0.5.0 (954 buckets, 3816 max)
[ 14.850336] xt_time: kernel timezone is -0000
[ 14.967406] PPP generic driver version 2.4.2
[ 14.977027] NET: Registered protocol family 24
[ 15.004703] b43-phy0: Broadcom 5357 WLAN found (core revision 28)
[ 15.012048] b43-phy0: Found PHY: Analog 9, Type 4 (N), Revision 9
[ 15.018285] b43-phy0 ERROR: FOUND UNSUPPORTED RADIO (Manuf 0x17F, ID 0x2057, Revision 5, Version 2)
[ 15.027643] b43: probe of bcma0:1 failed with error -122
[ 15.033407] Broadcom 43xx driver loaded [ Features: NL ]
[ 15.049885] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 17.644587] random: jshn: uninitialized urandom read (4 bytes read, 29 bits of entropy available)
[ 29.482118] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 29.489170] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 29.496033] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 35.264291] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 35.297289] device eth0.1 entered promiscuous mode
[ 35.302299] device eth0 entered promiscuous mode
[ 35.351811] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 35.568785] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 36.841641] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 36.877156] br-lan: port 1(eth0.1) entered forwarding state
[ 36.883060] br-lan: port 1(eth0.1) entered forwarding state
[ 36.888982] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 37.035007] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 38.881382] br-lan: port 1(eth0.1) entered forwarding state
[ 74.591424] random: nonblocking pool is initialized
[ 76.501417] done.
More information can be found at the following URL:
https://bugs.lede-project.org/index.php?do=details&task_id=1198
More information about the lede-bugs
mailing list