[FS#333] ath10k_pci: crash after ~10d uptime

LEDE Bugs lede-bugs at lists.infradead.org
Sun Feb 19 00:12:16 PST 2017


The following task has a new comment added:

FS#333 - ath10k_pci: crash after ~10d uptime
User who did this - Stijn Tintel (stintel)

----------
Just happened again after 4d uptime. This time, only wlan0 was active on the ath10k radio (no multi-AP).


[    9.945432] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[   10.169744] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2
[   10.180641] ath10k_pci 0000:00:00.0: Falling back to user helper
[   10.272271] firmware ath10k!pre-cal-pci-0000:00:00.0.bin: firmware_loading_store: map pages failed
[   10.569381] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[   10.578742] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[   10.591867] ath10k_pci 0000:00:00.0: firmware ver 10.2.4-1.0-00016 api 5 features no-p2p,raw-mode,mfp crc32 0c5668f8
[   10.602663] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[   10.613271] ath10k_pci 0000:00:00.0: Falling back to user helper
[   10.696442] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[   10.712219] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[   11.816627] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
[   11.922156] ath: EEPROM regdomain: 0x0
[   11.922172] ath: EEPROM indicates default country code should be used
[   11.922179] ath: doing EEPROM country->regdmn map search
[   11.922195] ath: country maps to regdmn code: 0x3a
[   11.922204] ath: Country alpha2 being used: US
[   11.922212] ath: Regpair used: 0x3a
[   12.285787] ath: EEPROM regdomain: 0x0
[   12.285803] ath: EEPROM indicates default country code should be used
[   12.285811] ath: doing EEPROM country->regdmn map search
[   12.285828] ath: country maps to regdmn code: 0x3a
[   12.285837] ath: Country alpha2 being used: US
[   12.285845] ath: Regpair used: 0x3a
[   21.409164] ath: EEPROM regdomain: 0x8038
[   21.413241] ath: EEPROM indicates we should expect a country code
[   21.419444] ath: doing EEPROM country->regdmn map search
[   21.424830] ath: country maps to regdmn code: 0x37
[   21.429702] ath: Country alpha2 being used: BE
[   21.434210] ath: Regpair used: 0x37
[   21.437750] ath: regdomain 0x8038 dynamically updated by user
[   21.443652] ath: EEPROM regdomain: 0x8038
[   21.447717] ath: EEPROM indicates we should expect a country code
[   21.453913] ath: doing EEPROM country->regdmn map search
[   21.459312] ath: country maps to regdmn code: 0x37
[   21.464165] ath: Country alpha2 being used: BE
[   21.468671] ath: Regpair used: 0x37
[   21.472223] ath: regdomain 0x8038 dynamically updated by user
[346092.285193] ath10k_pci 0000:00:00.0: failed to delete peer c0:ee:fb:4a:18:b7 for vdev 0: -145
[346092.293986] ath10k_pci 0000:00:00.0: found sta peer c0:ee:fb:4a:18:b7 (ptr 8f3ac000 id 95) entry on vdev 0 after it was supposedly removed
[346092.306790] ------------[ cut here ]------------
[346092.311694] WARNING: CPU: 0 PID: 1365 at compat-wireless-2016-10-08/net/mac80211/sta_info.c:964 sta_set_sinfo+0x928/0x9dc [mac80211]()
[346092.324069] Modules linked in: iptable_nat ath9k nf_nat_ipv4 nf_conntrack_ipv4 iptable_mangle iptable_filter ipt_REJECT ipt_MASQUERADE ip_tables ath9k_common xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG x_tables nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_nat nf_log_ipv4 nf_log_common nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack crc_ccitt ath9k_hw act_skbedit act_mirred em_u32 cls_u32 cls_tcindex cls_flow cls_route cls_fw sch_tbf sch_htb sch_hfsc sch_ingress ath10k_pci ath10k_core ath mac80211 cfg80211 compat sha256_generic jitterentropy_rng drbg hmac gpio_button_hotplug cryptomgr aead crypto_null crypto_hash
[346092.387902] CPU: 0 PID: 1365 Comm: hostapd Not tainted 4.4.47 #0
[346092.394085] Stack : 00000000 00000000 80496542 00000034 803c1518 00000000 00000001 80430000
[346092.394085]           80420000 80424d83 803bdb40 00000555 8049378c 80420000 8f44cc00 00000000
[346092.394085]           00000000 800a955c 803c3238 80420000 00000003 80420000 803c1644 8e977afc
[346092.394085]           8049378c 800a73f8 803c0000 00000000 00000001 80200300 00000000 00000000
[346092.394085]           00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[346092.394085]           ...
[346092.430540] Call Trace:
[346092.433124] [] show_stack+0x64/0xb0
[346092.437656] [] warn_slowpath_common+0xa0/0xd0
[346092.443051] [] warn_slowpath_null+0x18/0x24
[346092.448373] [] sta_set_sinfo+0x928/0x9dc [mac80211]
[346092.454381] [] __sta_info_destroy+0x30/0x48 [mac80211]
[346092.460686] [] sta_info_destroy_addr_bss+0x38/0x60 [mac80211]
[346092.467617] [] cfg80211_check_station_change+0xfb4/0x1528 [cfg80211]
[346092.475053] 
[346092.476674] ---[ end trace 24a608a72f7c1d41 ]---
[346095.495158] ath10k_pci 0000:00:00.0: failed to wait for created wmi peer c0:ee:fb:4a:18:b7 on vdev 0: -145
[346095.505059] ath10k_pci 0000:00:00.0: failed to add peer c0:ee:fb:4a:18:b7 for vdev 0 when adding a new sta: -145
[346293.634172] ath10k_pci 0000:00:00.0: failed to install key for vdev 0 peer a4:77:33:8c:8b:20: -11
[346293.643288] wlan0: failed to remove key (0, a4:77:33:8c:8b:20) from hardware (-11)
[346296.654141] ath10k_pci 0000:00:00.0: failed to install key for vdev 0 peer 9c:d6:43:29:cc:18: -11
[346296.663247] wlan0: failed to remove key (2, ff:ff:ff:ff:ff:ff) from hardware (-11)
[346299.664166] ath10k_pci 0000:00:00.0: failed to install key for vdev 0 peer 9c:d6:43:29:cc:18: -11
[346299.673266] wlan0: failed to set key (2, ff:ff:ff:ff:ff:ff) to hardware (-11)
[346302.694111] ath10k_pci 0000:00:00.0: failed to install key for vdev 0 peer b0:df:3a:12:79:80: -11
[346302.703216] wlan0: failed to remove key (0, b0:df:3a:12:79:80) from hardware (-11)
[346302.721527] ath10k_pci 0000:00:00.0: cipher 525 is not supported
[346302.727783] ath10k_pci 0000:00:00.0: failed to remove peer wep key 0: -122
[346302.734870] ath10k_pci 0000:00:00.0: failed to clear all peer wep keys for vdev 0: -122
[346302.743087] ath10k_pci 0000:00:00.0: failed to disassociate station: a4:77:33:8c:8b:20 vdev 0: -122
[346302.752360] ------------[ cut here ]------------
[346302.757275] WARNING: CPU: 0 PID: 1365 at compat-wireless-2016-10-08/net/mac80211/sta_info.c:956 sta_set_sinfo+0x8d4/0x9dc [mac80211]()
[346302.769626] Modules linked in: iptable_nat ath9k nf_nat_ipv4 nf_conntrack_ipv4 iptable_mangle iptable_filter ipt_REJECT ipt_MASQUERADE ip_tables ath9k_common xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG x_tables nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_nat nf_log_ipv4 nf_log_common nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack crc_ccitt ath9k_hw act_skbedit act_mirred em_u32 cls_u32 cls_tcindex cls_flow cls_route cls_fw sch_tbf sch_htb sch_hfsc sch_ingress ath10k_pci ath10k_core ath mac80211 cfg80211 compat sha256_generic jitterentropy_rng drbg hmac gpio_button_hotplug cryptomgr aead crypto_null crypto_hash
[346302.833445] CPU: 0 PID: 1365 Comm: hostapd Tainted: G        W       4.4.47 #0
[346302.840866] Stack : 00000000 00000000 80496542 00000042 803c1518 00000000 00000001 80430000
[346302.840866]           80420000 80424d83 803bdb40 00000555 8049378c 80420000 8f44cc00 00000000
[346302.840866]           00000000 800a955c 803c3238 80420000 00000003 80420000 803c1644 8e977afc
[346302.840866]           8049378c 800a73f8 8e977af8 00000000 80423e90 80200300 00000000 00000000
[346302.840866]           00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[346302.840866]           ...
[346302.877322] Call Trace:
[346302.879902] [] show_stack+0x64/0xb0
[346302.884429] [] warn_slowpath_common+0xa0/0xd0
[346302.889824] [] warn_slowpath_null+0x18/0x24
[346302.895127] [] sta_set_sinfo+0x8d4/0x9dc [mac80211]
[346302.901127] [] __sta_info_destroy+0x30/0x48 [mac80211]
[346302.907423] [] sta_info_destroy_addr_bss+0x38/0x60 [mac80211]
[346302.914363] [] cfg80211_check_station_change+0xfb4/0x1528 [cfg80211]
[346302.921790]
[346302.923392] ---[ end trace 24a608a72f7c1d42 ]---
[346305.924133] ath10k_pci 0000:00:00.0: failed to delete peer a4:77:33:8c:8b:20 for vdev 0: -11
[346305.932794] ath10k_pci 0000:00:00.0: found sta peer a4:77:33:8c:8b:20 (ptr 8f3ac400 id 87) entry on vdev 0 after it was supposedly removed
[346305.956350] ath10k_pci 0000:00:00.0: cipher 525 is not supported
[346305.962603] ath10k_pci 0000:00:00.0: failed to remove peer wep key 0: -122
[346305.969718] ath10k_pci 0000:00:00.0: failed to clear all peer wep keys for vdev 0: -122
[346308.974069] ath10k_warn: 1 callbacks suppressed
[346308.978790] ath10k_pci 0000:00:00.0: failed to delete peer b0:df:3a:12:79:80 for vdev 0: -11
[346308.987491] ath10k_pci 0000:00:00.0: found sta peer b0:df:3a:12:79:80 (ptr 8f3cb200 id 243) entry on vdev 0 after it was supposedly removed
[346312.004059] ath10k_pci 0000:00:00.0: failed to set beacon mode for vdev 0: -11
[346315.004045] ath10k_pci 0000:00:00.0: failed to set dtim period for vdev 0: -11
[346318.024030] ath10k_pci 0000:00:00.0: failed to recalculate rts/cts prot for vdev 0: -11
[346321.024014] ath10k_pci 0000:00:00.0: failed to set protection mode 0 on vdev 0: -11
[346324.024003] ath10k_pci 0000:00:00.0: failed to set preamble for vdev 0: -11
[409419.602401] ath10k_pci 0000:00:00.0: failed to send pdev bss chan info request

----------

More information can be found at the following URL:
https://bugs.lede-project.org/index.php?do=details&task_id=333#comment1876



More information about the lede-bugs mailing list