[FS#1020] Mikrotik RB493G AR8316 switch0/ETH0 cannot be managed
LEDE Bugs
lede-bugs at lists.infradead.org
Tue Dec 19 13:05:12 PST 2017
The following task has a new comment added:
FS#1020 - Mikrotik RB493G AR8316 switch0/ETH0 cannot be managed
User who did this - betelgeux1 (betelgeux1)
----------
[ 0.000000] Linux version 4.4.92 (buildbot at builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3103-1b51a49) ) #0 Tue Oct 17 17:46:20 2017
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR7161 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 10000000 @ 00000000 (usable)
[ 0.000000] User-defined physical RAM map:
[ 0.000000] memory: 10000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] No valid device tree found, continuing without
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] On node 0 totalpages: 65536
[ 0.000000] free_area_init_node: node 0, pgdat 804304d0, node_mem_map 81000000
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65536 pages, LIFO batch:15
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: parts=1 boot_part_size=4194304 gpio=4023 HZ=340000000 mem=256M kmac=64:D1:54:59:44:26 board=493G ver=3.24 hw_opt=00020004 boot=1 mlc=9 console=ttyS0,115200 rootfstype=squashfs noinitrd
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 254960K/262144K available (3399K kernel code, 177K rwdata, 468K rodata, 236K init, 203K bss, 7184K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:680.000MHz, DDR:340.000MHz, AHB:170.000MHz, Ref:40.000MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5621354254 ns
[ 0.000008] sched_clock: 32 bits at 340MHz, resolution 2ns, wraps every 6316128254ns
[ 0.007797] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
[ 0.070513] pid_max: default: 32768 minimum: 301
[ 0.075245] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.081854] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.091128] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.100990] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.108125] NET: Registered protocol family 16
[ 0.113919] MIPS: machine is MikroTik RouterBOARD 493G
[ 2.748964] registering PCI controller with io_map_base unset
[ 2.754725] Can't analyze schedule() prologue at 800670fc
[ 2.767688] rb4xx-spi rb4xx-spi: master is unqueued, this is deprecated
[ 2.775310] PCI host bridge to bus 0000:00
[ 2.779413] pci_bus 0000:00: root bus resource [mem 0x10000000-0x16ffffff]
[ 2.786305] pci_bus 0000:00: root bus resource [io 0x0000]
[ 2.791866] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 2.798646] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 2.806602] pci 0000:00:14.0: [168c:0029] type 00 class 0x028000
[ 2.806641] pci 0000:00:14.0: reg 0x10: [mem 0x00000000-0x0000ffff]
[ 2.806707] pci 0000:00:14.0: PME# supported from D0 D3hot
[ 2.806894] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 2.806924] pci 0000:00:14.0: BAR 0: assigned [mem 0x10000000-0x1000ffff]
[ 2.813738] pci 0000:00:14.0: using irq 42 for pin 1
[ 2.819419] clocksource: Switched to clocksource MIPS
[ 2.825446] NET: Registered protocol family 2
[ 2.830659] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 2.837644] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 2.844067] TCP: Hash tables configured (established 2048 bind 2048)
[ 2.850518] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 2.856354] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 2.862866] NET: Registered protocol family 1
[ 2.867255] PCI: CLS 0 bytes, default 32
[ 2.871537] Crashlog allocated RAM at address 0x3f00000
[ 2.889267] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.895146] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 2.907278] io scheduler noop registered
[ 2.911248] io scheduler deadline registered (default)
[ 2.916637] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 2.925405] console [ttyS0] disabled
[ 2.949036] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 10625000) is a 16550A
[ 2.957748] console [ttyS0] enabled
[ 2.964713] bootconsole [early0] disabled
[ 2.973554] m25p80 spi0.0: pm25lv512 (64 Kbytes)
[ 2.978177] Creating 4 MTD partitions on "spi0.0":
[ 2.983013] 0x000000000000-0x00000000b000 : "routerboot"
[ 2.992447] 0x00000000b000-0x00000000c000 : "hard_config"
[ 2.999222] 0x00000000d000-0x00000000f000 : "bios"
[ 3.005516] 0x00000000f000-0x000000010000 : "soft_config"
[ 3.012548] NAND flash driver for RouterBoard 4xx series version 0.2.0
[ 3.019328] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1
[ 3.025723] nand: Samsung NAND 128MiB 3,3V 8-bit
[ 3.030341] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 3.037923] Scanning device for bad blocks
[ 3.197631] Bad eraseblock 447 at 0x0000037e0000
[ 3.222870] Bad eraseblock 507 at 0x000003f60000
[ 3.406258] Creating 3 MTD partitions on "NAND 128MiB 3,3V 8-bit":
[ 3.412446] 0x000000000000-0x000000040000 : "booter"
[ 3.418698] 0x000000040000-0x000000400000 : "kernel"
[ 3.425183] 0x000000400000-0x000008000000 : "ubi"
[ 3.439354] **switch0: Atheros AR8316 rev. 1 switch registered on gpio**
[ 3.445771] libphy: GPIO Bitbanged MDIO: probed
[ 3.455262] **switch1: Atheros AR8316 rev. 1 switch registered on ag71xx-mdio.0**
[ 3.462456] libphy: ag71xx_mdio: probed
[ 3.780830] ar8316: Using port 4 as switch port
[ 3.828437] ag71xx ag71xx.1: connected to PHY at gpio:00 [uid=004dd041, driver=Atheros AR8216/AR8236/AR8316]
[ 3.838883] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:RGMII
[ 4.160789] ar8316: Using port 4 as switch port
[ 4.195443] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd041, driver=Atheros AR8216/AR8236/AR8316]
[ 4.206670] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 4.214733] NET: Registered protocol family 10
[ 4.222649] NET: Registered protocol family 17
[ 4.227151] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 4.239885] 8021q: 802.1Q VLAN Support v1.8
[ 4.244210] rb: no calibration data found
[ 4.251327] UBI: auto-attach mtd6
[ 4.254490] ubi0: attaching mtd6
[ 7.339318] ubi0: scanning is finished
[ 7.405204] ubi0: attached mtd6 (name "ubi", size 124 MiB)
[ 7.410743] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 7.417600] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 7.424381] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 7.431333] ubi0: good PEBs: 990, bad PEBs: 2, corrupted PEBs: 0
[ 7.437325] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 7.444540] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 271852037
[ 7.453569] ubi0: available PEBs: 0, total reserved PEBs: 990, PEBs reserved for bad PEB handling: 18
[ 7.462892] ubi0: background thread "ubi_bgt0d" started, PID 329
[ 7.470774] block ubiblock0_1: created from ubi0:1(rootfs)
[ 7.476258] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[ 7.497933] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 7.506119] Freeing unused kernel memory: 236K
[ 9.070160] init: Console is alive
[ 9.073779] init: - watchdog -
[ 10.391280] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 10.459653] usbcore: registered new interface driver usbfs
[ 10.465223] usbcore: registered new interface driver hub
[ 10.470639] usbcore: registered new device driver usb
[ 10.480128] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 10.487949] ehci-platform: EHCI generic platform driver
[ 10.493329] ehci-platform ehci-platform: EHCI Host Controller
[ 10.499095] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 10.507120] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 10.529436] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 10.536538] hub 1-0:1.0: USB hub found
[ 10.540648] hub 1-0:1.0: 2 ports detected
[ 10.547084] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 10.554464] ohci-platform: OHCI generic platform driver
[ 10.559839] ohci-platform ohci-platform: Generic Platform OHCI controller
[ 10.566636] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
[ 10.574625] ohci-platform ohci-platform: irq 14, io mem 0x1c000000
[ 10.644306] hub 2-0:1.0: USB hub found
[ 10.648355] hub 2-0:1.0: 2 ports detected
[ 10.653214] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 10.670877] init: - preinit -
[ 11.298295] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 13.160006] ar71xx: pll_reg 0xb8050014: 0x110000
[ 13.160031] eth0: link up (1000Mbps/Full duplex)
[ 13.164746] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 14.424829] random: procd: uninitialized urandom read (4 bytes read, 24 bits of entropy available)
[ 14.439920] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 397
[ 14.776009] UBIFS (ubi0:2): recovery needed
[ 15.335548] UBIFS (ubi0:2): recovery completed
[ 15.340099] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[ 15.347916] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 15.357907] UBIFS (ubi0:2): FS size: 117579776 bytes (112 MiB, 926 LEBs), journal size 5840896 bytes (5 MiB, 46 LEBs)
[ 15.368503] UBIFS (ubi0:2): reserved for root: 4952683 bytes (4836 KiB)
[ 15.375120] UBIFS (ubi0:2): media format: w4/r0 (latest is w4/r0), UUID A51DB03D-DAD5-4F0B-B171-0BC1B108293D, small LPT model
[ 15.406702] mount_root: switching to ubifs overlay
[ 15.426408] urandom-seed: Seeding with /etc/urandom.seed
[ 15.618841] eth0: link down
[ 15.636915] procd: - early -
[ 15.639990] procd: - watchdog -
[ 16.264662] procd: - watchdog -
[ 16.268047] procd: - ubus -
[ 16.306198] random: ubusd: uninitialized urandom read (4 bytes read, 27 bits of entropy available)
[ 16.330301] random: ubusd: uninitialized urandom read (4 bytes read, 27 bits of entropy available)
[ 16.339745] random: ubusd: uninitialized urandom read (4 bytes read, 27 bits of entropy available)
[ 16.348744] random: ubusd: uninitialized urandom read (4 bytes read, 27 bits of entropy available)
[ 16.358172] random: ubusd: uninitialized urandom read (4 bytes read, 27 bits of entropy available)
[ 16.367215] random: ubusd: uninitialized urandom read (4 bytes read, 27 bits of entropy available)
[ 16.376353] random: ubusd: uninitialized urandom read (4 bytes read, 27 bits of entropy available)
[ 16.385508] random: ubusd: uninitialized urandom read (4 bytes read, 27 bits of entropy available)
[ 16.394843] procd: - init -
[ 16.813708] kmodloader: loading kernel modules from /etc/modules.d/*
[ 16.824644] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 16.842330] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[ 16.850380] Backport generated by backports.git backports-20160324-13-g24da7d3c
[ 16.860628] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 16.872998] nf_conntrack version 0.5.0 (3987 buckets, 15948 max)
[ 16.912048] xt_time: kernel timezone is -0000
[ 16.965617] PPP generic driver version 2.4.2
[ 16.972183] NET: Registered protocol family 24
[ 17.007927] PCI: Enabling device 0000:00:14.0 (0000 -> 0002)
[ 18.571904] ath: EEPROM regdomain: 0x0
[ 18.571922] ath: EEPROM indicates default country code should be used
[ 18.571930] ath: doing EEPROM country->regdmn map search
[ 18.571947] ath: country maps to regdmn code: 0x3a
[ 18.571957] ath: Country alpha2 being used: US
[ 18.571965] ath: Regpair used: 0x3a
[ 18.591260] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 18.595969] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=42
[ 19.233301] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 19.754253] random: jshn: uninitialized urandom read (4 bytes read, 32 bits of entropy available)
[ 26.362641] device eth0 entered promiscuous mode
[ 26.442575] IPv6: ADDRCONF(NETDEV_UP): br-3RD_PARTY: link is not ready
[ 26.502493] device eth0.5 entered promiscuous mode
[ 26.535971] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 26.595127] device eth1.1 entered promiscuous mode
[ 26.599991] device eth1 entered promiscuous mode
[ 26.640572] IPv6: ADDRCONF(NETDEV_UP): eth1.7: link is not ready
[ 26.688237] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 26.800569] IPv6: ADDRCONF(NETDEV_UP): eth1.2: link is not ready
[ 27.820007] ar71xx: pll_reg 0xb8050010: 0x110000
[ 27.824634] eth1: link up (1000Mbps/Full duplex)
[ 27.873563] ar71xx: pll_reg 0xb8050014: 0x110000
[ 27.878190] eth0: link up (1000Mbps/Full duplex)
Switch 1 is functional, Switch 0 is unstable.
----------
More information can be found at the following URL:
https://bugs.lede-project.org/index.php?do=details&task_id=1020#comment4009
More information about the lede-bugs
mailing list