[FS#1206] ath kernel oops on boot
LEDE Bugs
lede-bugs at lists.infradead.org
Tue Dec 5 07:01:05 PST 2017
A new Flyspray task has been opened. Details are below.
User who did this - Kyle Gordon (kylegordon)
Attached to Project - LEDE Project
Summary - ath kernel oops on boot
Task Type - Bug Report
Category - Base system
Status - Unconfirmed
Assigned To -
Operating System - All
Severity - High
Priority - Very Low
Reported Version - lede-17.01
Due in Version - Undecided
Due Date - Undecided
Details - Supply the following if possible:
- Device problem occurs on :
Meraki MR18
- Software versions of LEDE release, packages, etc.
Standard 17.01.4.
- Steps to reproduce
This is happening on a Meraki MR18, bootstrapped using @riptidewave93s bringup method described at https://medium.com/openwrt-iot/lede-openwrt-installing-firmware-on-meraki-mr18-e96e4e081710. It was then sysupgraded to 17.01, and then 17.01.4 when appropriate.
Following a LEDE factory reset in order to wipe the configuration, it is now seemingly unable to bring up 2 of the 3 radio interfaces. The following output has been observed in dmesg, where it seems that the ath module is causing a kernel oops.
My other MR18 with LEDE 17.04.1 has not been reset in this manner, and continues to work, and does not exhibit the kernel oops on boot.
'iw phy' lists all 3 radios, whereas 'iw dev' lists only wlan2.
root at wap01:~# dmesg
[ 0.000000] Linux version 4.4.92 (buildbot at builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3102-0224e32) ) #0 Mon Oct 16 15:21:43 2017
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] No valid device tree found, continuing without
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat 8042a4d0, node_mem_map 81000000
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=MR18 mtdparts=ar934x-nfc:512k(nandloader)ro,8M(kernel),8M(recovery),113664k(ubi),128k at 130944k(odm-caldata)ro console=ttyS0,115200 rootfstype=squashfs noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 125008K/131072K available (3384K kernel code, 160K rwdata, 464K rodata, 272K init, 204K bss, 6064K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:720.000MHz, DDR:600.000MHz, AHB:200.000MHz, Ref:40.000MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5309056796 ns
[ 0.000007] sched_clock: 32 bits at 360MHz, resolution 2ns, wraps every 5965232126ns
[ 0.008281] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
[ 0.071178] pid_max: default: 32768 minimum: 301
[ 0.076185] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.083229] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.092549] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.103047] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.110398] NET: Registered protocol family 16
[ 0.116135] MIPS: machine is Meraki MR18
[ 0.120356] SGMII cal value = 0x1
[ 0.137188] ar71xx: using random MAC address for eth0
[ 0.355689] registering PCI controller with io_map_base unset
[ 0.361902] registering PCI controller with io_map_base unset
[ 0.368044] Can't analyze schedule() prologue at 800670fc
[ 0.381023] PCI host bridge to bus 0000:00
[ 0.385391] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
[ 0.392734] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.398657] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.405880] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.414334] pci 0000:00:00.0: [168c:0033] type 00 class 0x028000
[ 0.414390] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x0001ffff 64bit]
[ 0.414443] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 0.414500] pci 0000:00:00.0: supports D1
[ 0.414513] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.414688] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.414715] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
[ 0.422531] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
[ 0.430305] PCI host bridge to bus 0000:01
[ 0.434679] pci_bus 0000:01: root bus resource [mem 0x12000000-0x13ffffff]
[ 0.441991] pci_bus 0000:01: root bus resource [io 0x0001]
[ 0.447922] pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
[ 0.455137] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[ 0.463589] pci 0000:01:00.0: [168c:0033] type 00 class 0x028000
[ 0.463643] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x0001ffff 64bit]
[ 0.463696] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 0.463752] pci 0000:01:00.0: supports D1
[ 0.463764] pci 0000:01:00.0: PME# supported from D0 D1 D3hot
[ 0.463956] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.463982] pci 0000:01:00.0: BAR 0: assigned [mem 0x12000000-0x1201ffff 64bit]
[ 0.471768] pci 0000:01:00.0: BAR 6: assigned [mem 0x12020000-0x1202ffff pref]
[ 0.479477] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.484756] pci 0000:01:00.0: using irq 41 for pin 1
[ 0.490601] clocksource: Switched to clocksource MIPS
[ 0.496799] NET: Registered protocol family 2
[ 0.502181] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.509600] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.516405] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.523240] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.529462] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.536355] NET: Registered protocol family 1
[ 0.541046] PCI: CLS 0 bytes, default 32
[ 0.544625] Crashlog allocated RAM at address 0x3f00000
[ 0.561412] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.567618] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.580210] io scheduler noop registered
[ 0.584419] io scheduler deadline registered (default)
[ 0.590054] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.598964] console [ttyS0] disabled
[ 0.622846] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[ 0.632027] console [ttyS0] enabled
[ 0.639437] bootconsole [early0] disabled
[ 0.651742] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[ 0.658192] nand: Hynix NAND 128MiB 3,3V 8-bit
[ 0.662725] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.673052] Scanning device for bad blocks
[ 0.690187] Bad eraseblock 143 at 0x0000011e0000
[ 0.774205] 5 cmdlinepart partitions found on MTD device ar934x-nfc
[ 0.780564] Creating 5 MTD partitions on "ar934x-nfc":
[ 0.785792] 0x000000000000-0x000000080000 : "nandloader"
[ 0.792262] 0x000000080000-0x000000880000 : "kernel"
[ 0.798504] 0x000000880000-0x000001080000 : "recovery"
[ 0.804975] 0x000001080000-0x000007f80000 : "ubi"
[ 0.811127] 0x000007fe0000-0x000008000000 : "odm-caldata"
[ 0.826459] libphy: ag71xx_mdio: probed
[ 1.491062] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:03 [uid=004dd072, driver=Atheros 8035 ethernet]
[ 1.501751] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 1.509674] NET: Registered protocol family 10
[ 1.517933] NET: Registered protocol family 17
[ 1.522545] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.535425] 8021q: 802.1Q VLAN Support v1.8
[ 1.542669] UBI: auto-attach mtd3
[ 1.545870] ubi0: attaching mtd3
[ 2.163553] random: nonblocking pool is initialized
[ 2.936556] ubi0: scanning is finished
[ 2.957334] ubi0: attached mtd3 (name "ubi", size 111 MiB)
[ 2.962939] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[ 2.969907] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[ 2.976710] ubi0: VID header offset: 512 (aligned 512), data offset: 2048
[ 2.983601] ubi0: good PEBs: 887, bad PEBs: 1, corrupted PEBs: 0
[ 2.989689] ubi0: user volume: 9, internal volumes: 1, max. volumes count: 128
[ 2.997020] ubi0: max/mean erase counter: 5/1, WL threshold: 4096, image sequence number: 0
[ 3.005495] ubi0: available PEBs: 0, total reserved PEBs: 887, PEBs reserved for bad PEB handling: 19
[ 3.014890] ubi0: background thread "ubi_bgt0d" started, PID 281
[ 3.022538] block ubiblock0_7: created from ubi0:7(rootfs)
[ 3.028103] ubiblock: device ubiblock0_7 (rootfs) set to be root filesystem
[ 3.035202] hctosys: unable to open rtc device (rtc0)
[ 3.048290] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 3.056554] Freeing unused kernel memory: 272K
[ 3.852046] init: Console is alive
[ 3.855661] init: - watchdog -
[ 4.500248] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.559283] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.568181] init: - preinit -
[ 5.026626] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 8.140838] UBIFS (ubi0:8): background thread "ubifs_bgt0_8" started, PID 352
[ 8.221278] UBIFS (ubi0:8): recovery needed
[ 8.369959] UBIFS (ubi0:8): recovery completed
[ 8.374576] UBIFS (ubi0:8): UBIFS: mounted UBI device 0, volume 8, name "rootfs_data"
[ 8.382533] UBIFS (ubi0:8): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 8.392594] UBIFS (ubi0:8): FS size: 56770560 bytes (54 MiB, 440 LEBs), journal size 2838528 bytes (2 MiB, 22 LEBs)
[ 8.403177] UBIFS (ubi0:8): reserved for root: 2681413 bytes (2618 KiB)
[ 8.409890] UBIFS (ubi0:8): media format: w4/r0 (latest is w4/r0), UUID 09620A94-9D7B-4368-AA5D-6EBEFB8A1C9A, small LPT model
[ 8.443717] mount_root: switching to ubifs overlay
[ 8.467726] urandom-seed: Seeding with /etc/urandom.seed
[ 8.562556] eth0: link up (1000Mbps/Full duplex)
[ 8.567263] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 8.668732] eth0: link down
[ 8.683277] procd: - early -
[ 8.686279] procd: - watchdog -
[ 9.297752] procd: - watchdog -
[ 9.301172] procd: - ubus -
[ 9.363301] procd: - init -
[ 10.614195] kmodloader: loading kernel modules from /etc/modules.d/*
[ 10.624283] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.638306] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[ 10.646472] Backport generated by backports.git backports-20160324-13-g24da7d3c
[ 10.656313] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.667657] nf_conntrack version 0.5.0 (1957 buckets, 7828 max)
[ 10.700467] xt_time: kernel timezone is -0000
[ 10.745027] PPP generic driver version 2.4.2
[ 10.752078] NET: Registered protocol family 24
[ 10.794208] ath: EEPROM regdomain: 0x0
[ 10.794224] ath: EEPROM indicates default country code should be used
[ 10.794231] ath: doing EEPROM country->regdmn map search
[ 10.794247] ath: country maps to regdmn code: 0x3a
[ 10.794256] ath: Country alpha2 being used: US
[ 10.794263] ath: Regpair used: 0x3a
[ 10.809335] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 10.813371] ieee80211 phy0: Atheros AR9550 Rev:0 mem=0xb8100000, irq=47
[ 10.820216] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 10.852952] ath: EEPROM regdomain: 0x0
[ 10.852968] ath: EEPROM indicates default country code should be used
[ 10.852976] ath: doing EEPROM country->regdmn map search
[ 10.852992] ath: country maps to regdmn code: 0x3a
[ 10.853001] ath: Country alpha2 being used: US
[ 10.853008] ath: Regpair used: 0x3a
[ 10.861819] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 10.865810] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40
[ 10.872605] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[ 10.907139] ath: EEPROM regdomain: 0x0
[ 10.907155] ath: EEPROM indicates default country code should be used
[ 10.907162] ath: doing EEPROM country->regdmn map search
[ 10.907178] ath: country maps to regdmn code: 0x3a
[ 10.907186] ath: Country alpha2 being used: US
[ 10.907194] ath: Regpair used: 0x3a
[ 10.915446] ieee80211 phy2: Selected rate control algorithm 'minstrel_ht'
[ 10.919427] ieee80211 phy2: Atheros AR9300 Rev:4 mem=0xb2000000, irq=41
[ 10.929518] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 16.210465] device eth0 entered promiscuous mode
[ 16.228636] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 17.275843] ath: EEPROM regdomain: 0x833a
[ 17.279912] ath: EEPROM indicates we should expect a country code
[ 17.286133] ath: doing EEPROM country->regdmn map search
[ 17.291530] ath: country maps to regdmn code: 0x37
[ 17.296385] ath: Country alpha2 being used: GB
[ 17.300899] ath: Regpair used: 0x37
[ 17.304437] ath: regdomain 0x833a dynamically updated by user
[ 17.310338] ath: EEPROM regdomain: 0x833a
[ 17.314410] ath: EEPROM indicates we should expect a country code
[ 17.320587] ath: doing EEPROM country->regdmn map search
[ 17.325980] ath: country maps to regdmn code: 0x37
[ 17.330845] ath: Country alpha2 being used: GB
[ 17.335350] ath: Regpair used: 0x37
[ 17.338880] ath: regdomain 0x833a dynamically updated by user
[ 17.344769] ath: EEPROM regdomain: 0x833a
[ 17.348832] ath: EEPROM indicates we should expect a country code
[ 17.355025] ath: doing EEPROM country->regdmn map search
[ 17.360406] ath: country maps to regdmn code: 0x37
[ 17.365270] ath: Country alpha2 being used: GB
[ 17.369776] ath: Regpair used: 0x37
[ 17.373324] ath: regdomain 0x833a dynamically updated by user
[ 18.005216] ------------[ cut here ]------------
[ 18.009925] WARNING: CPU: 0 PID: 1022 at compat-wireless-2017-01-31/net/mac80211/driver-ops.h:167 0x87681850 [mac80211 at 87680000+0x607a0]()
[ 18.022581] Modules linked in: ath9k ath9k_common pppoe ppp_async iptable_nat ath9k_hw ath pppox ppp_generic nf_nat_ipv4 nf_conntrack_ipv6 nf_conntrack_ipv4 mac80211 ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_CT spi_gpio slhc nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack iptable_mangle iptable_filter ip_tables crc_ccitt compat ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables x_tables gpio_button_hotplug
[ 18.081941] CPU: 0 PID: 1022 Comm: iw Not tainted 4.4.92 #0
[ 18.087592] Stack : 803dcb4c 00000000 00000001 80430000 00000000 00000000 00000000 00000000
[ 18.087592] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 18.087592] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 18.087592] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 18.087592] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 18.087592] ...
[ 18.123953] Call Trace:[] 0x800719e8
[ 18.128470] [] 0x800719e8
[ 18.132017] [] 0x800817e4
[ 18.135560] [] 0x87681850 [mac80211 at 87680000+0x607a0]
[ 18.141576] [] 0x8008189c
[ 18.145110] [] 0x802aa3bc
[ 18.148658] [] 0x800d68ec
[ 18.152209] [] 0x87681850 [mac80211 at 87680000+0x607a0]
[ 18.158219] [] 0x8769e5b4 [mac80211 at 87680000+0x607a0]
[ 18.164232] [] 0x875dd020 [cfg80211 at 875c0000+0x36a40]
[ 18.170237] [] 0x802aa3bc
[ 18.173783] [] 0x80205048
[ 18.177318] [] 0x802e4fb0
[ 18.180872] [] 0x802e7de0
[ 18.184419] [] 0x802e7b64
[ 18.187957] [] 0x802e6fa4
[ 18.191507] [] 0x802aa2d0
[ 18.195044] [] 0x802e7b4c
[ 18.198582] [] 0x802e6808
[ 18.202132] [] 0x802aa3cc
[ 18.205677] [] 0x802e6d70
[ 18.209210] [] 0x801ec428
[ 18.212760] [] 0x802aec1c
[ 18.216299] [] 0x802a0640
[ 18.219834] [] 0x802a1a58
[ 18.223384] [] 0x800f0284
[ 18.226923] [] 0x800f326c
[ 18.230462] [] 0x802d1d80
[ 18.234010] [] 0x8034c024
[ 18.237552] [] 0x80076754
[ 18.241094] [] 0x8011c690
[ 18.244640] [] 0x801194f0
[ 18.248180] [] 0x802a2984
[ 18.251727] [] 0x801071b0
[ 18.255263] [] 0x80062c6c
[ 18.258800]
[ 18.260310] ---[ end trace adb867f205f892d9 ]---
[ 18.879651] eth0: link up (1000Mbps/Full duplex)
[ 18.885871] br-lan: port 1(eth0) entered forwarding state
[ 18.891425] br-lan: port 1(eth0) entered forwarding state
[ 18.990866] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 20.890648] br-lan: port 1(eth0) entered forwarding state
root at wap01:~# uptime
14:31:37 up 0 min, load average: 0.50, 0.16, 0.05
root at wap01:~# ifconfig -a
br-lan Link encap:Ethernet HWaddr 00:18:0A:84:3A:F1
inet addr:172.24.32.15 Bcast:172.24.32.255 Mask:255.255.255.0
inet6 addr: fe80::218:aff:fe84:3af1/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:7693 errors:0 dropped:0 overruns:0 frame:0
TX packets:3075 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1027812 (1003.7 KiB) TX bytes:753010 (735.3 KiB)
eth0 Link encap:Ethernet HWaddr 00:18:0A:84:3A:F1
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:7693 errors:0 dropped:0 overruns:0 frame:0
TX packets:3076 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1137914 (1.0 MiB) TX bytes:753100 (735.4 KiB)
Interrupt:4
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:16 errors:0 dropped:0 overruns:0 frame:0
TX packets:16 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1
RX bytes:1621 (1.5 KiB) TX bytes:1621 (1.5 KiB)
wlan2 Link encap:UNSPEC HWaddr 00-18-0A-84-3A-F4-30-30-00-00-00-00-00-00-00-00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:121 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:24004 (23.4 KiB) TX bytes:0 (0.0 B)
root at wap01:~#
More information can be found at the following URL:
https://bugs.lede-project.org/index.php?do=details&task_id=1206
More information about the lede-bugs
mailing list