[FS#957] Archer C2600 boots slowly
LEDE Bugs
lede-bugs at lists.infradead.org
Sun Aug 13 13:53:16 PDT 2017
A new Flyspray task has been opened. Details are below.
User who did this - nopnopnop (nopnopnop)
Attached to Project - LEDE Project
Summary - Archer C2600 boots slowly
Task Type - Bug Report
Category - Kernel
Status - Unconfirmed
Assigned To -
Operating System - All
Severity - Medium
Priority - Very Low
Reported Version - Trunk
Due in Version - Undecided
Due Date - Undecided
Details - An Archer C2600 v1.1 boots very slowly. A few minutes pass between power on and the first replies to ping.
LEDE commit: df3295f50e54909090846de12f7deb3ff8de6557
It's the same after every reboot and power on operation.
I had to power cycle the router after flashing a newer version of LEDE built from trunk. It didn't seem to boot automatically after flashing.
Full kernel log:
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.40 (wrt at ed3110359c81) (gcc version 5.4.0 (LEDE GCC 5.4.0 r4651-a6f6f8d) ) #0 SMP Fri Aug 11 16:12:56 2017
[ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt:Machine model: TP-Link Archer C2600
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 122880
[ 0.000000] free_area_init_node: node 0, pgdat c079d000, node_mem_map ddc39000
[ 0.000000] Normal zone: 960 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 122880 pages, LIFO batch:31
[ 0.000000] percpu: Embedded 13 pages/cpu @ddc06000 s21068 r8192 d23988 u53248
[ 0.000000] pcpu-alloc: s21068 r8192 d23988 u53248 alloc=13*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 121920
[ 0.000000] Kernel command line:
[ 0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8 root=mtd:rootfs rootfstype=squashfs
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 481048K/491520K available (3862K kernel code, 246K rwdata, 1236K rodata, 240K init, 242K bss, 10472K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xde800000 - 0xff800000 ( 528 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xde000000 ( 480 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0208000 - 0xc05cdc20 (3864 kB)
[ 0.000000] .init : 0xc0724000 - 0xc0760000 ( 240 kB)
[ 0.000000] .data : 0xc0760000 - 0xc079d900 ( 247 kB)
[ 0.000000] .bss : 0xc079f000 - 0xc07db828 ( 243 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[ 0.000008] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[ 0.000022] Switching to timer-based delay loop, resolution 160ns
[ 0.000224] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[ 0.000245] pid_max: default: 32768 minimum: 301
[ 0.000351] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000364] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.001015] CPU: Testing write buffer coherency: ok
[ 0.001302] Setting up static identity map for 0x42208280 - 0x422082d8
[ 0.004610] Brought up 2 CPUs
[ 0.004627] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[ 0.004636] CPU: All CPU(s) started in SVC mode.
[ 0.016579] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[ 0.016766] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.016792] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.016871] pinctrl core: initialized pinctrl subsystem
[ 0.018176] NET: Registered protocol family 16
[ 0.018425] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.041430] cpuidle: using governor ladder
[ 0.072446] cpuidle: using governor menu
[ 0.074598] qcom_rpm 108000.rpm: could not find pctldev for node /soc/pinmux at 800000/i2c4_pinmux, deferring probe
[ 0.125127] msm_bus_fabric_init_driver
[ 0.126271] usbcore: registered new interface driver usbfs
[ 0.126372] usbcore: registered new interface driver hub
[ 0.126460] usbcore: registered new device driver usb
[ 0.126519] pps_core: LinuxPPS API ver. 1 registered
[ 0.126531] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[ 0.126563] PTP clock support registered
[ 0.128572] clocksource: Switched to clocksource dg_timer
[ 0.132624] NET: Registered protocol family 2
[ 0.133219] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.133267] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.133326] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.133379] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.133403] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.133597] NET: Registered protocol family 1
[ 0.133650] PCI: CLS 0 bytes, default 64
[ 0.135132] No memory allocated for crashlog
[ 0.135436] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 0.141817] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.141834] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.148445] io scheduler noop registered
[ 0.148465] io scheduler deadline registered (default)
[ 0.149994] 1b500000.pci supply vdda not found, using dummy regulator
[ 0.150101] 1b500000.pci supply vdda_phy not found, using dummy regulator
[ 0.150198] 1b500000.pci supply vdda_refclk not found, using dummy regulator
[ 0.151016] OF: PCI: host bridge /soc/pci at 1b500000 ranges:
[ 0.151061] OF: PCI: IO 0x0fe00000..0x0fefffff -> 0x0fe00000
[ 0.151089] OF: PCI: MEM 0x08000000..0x0fdfffff -> 0x08000000
[ 0.259343] qcom-pcie 1b500000.pci: link up
[ 0.261430] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[ 0.261452] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.261472] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff])
[ 0.261488] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[ 0.261504] pci_bus 0000:00: scanning bus
[ 0.261550] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400
[ 0.261644] pci 0000:00:00.0: calling pci_fixup_ide_bases+0x0/0x3c
[ 0.261713] pci 0000:00:00.0: supports D1
[ 0.261724] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.261743] pci 0000:00:00.0: PME# disabled
[ 0.262022] pci_bus 0000:00: fixups for bus
[ 0.262043] PCI: bus0: Fast back to back transfers disabled
[ 0.262063] pci 0000:00:00.0: scanning [bus 01-01] behind bridge, pass 0
[ 0.262206] pci_bus 0000:01: scanning bus
[ 0.262381] pci 0000:01:00.0: [168c:0040] type 00 class 0x028000
[ 0.262611] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.263062] pci 0000:01:00.0: calling pci_fixup_ide_bases+0x0/0x3c
[ 0.263701] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.263742] pci 0000:01:00.0: PME# disabled
[ 0.264090] pci_bus 0000:01: fixups for bus
[ 0.264159] PCI: bus1: Fast back to back transfers disabled
[ 0.264173] pci_bus 0000:01: bus scan returning with max=01
[ 0.264191] pci 0000:00:00.0: scanning [bus 01-01] behind bridge, pass 1
[ 0.264207] pci_bus 0000:00: bus scan returning with max=01
[ 0.264345] pci 0000:00:00.0: fixup irq: got 133
[ 0.264355] pci 0000:00:00.0: assigning IRQ 133
[ 0.264436] pci 0000:01:00.0: fixup irq: got 133
[ 0.264446] pci 0000:01:00.0: assigning IRQ 133
[ 0.264512] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[ 0.264537] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[ 0.264666] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.264689] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
[ 0.265112] aer 0000:00:00.0:pcie002: service driver aer loaded
[ 0.265505] 1b700000.pci supply vdda not found, using dummy regulator
[ 0.265607] 1b700000.pci supply vdda_phy not found, using dummy regulator
[ 0.265690] 1b700000.pci supply vdda_refclk not found, using dummy regulator
[ 0.266481] OF: PCI: host bridge /soc/pci at 1b700000 ranges:
[ 0.266515] OF: PCI: IO 0x31e00000..0x31efffff -> 0x31e00000
[ 0.266538] OF: PCI: MEM 0x2e000000..0x31dfffff -> 0x2e000000
[ 0.376805] qcom-pcie 1b700000.pci: link up
[ 0.378847] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[ 0.378866] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 0.378883] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[ 0.378897] pci_bus 0001:00: scanning bus
[ 0.378935] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400
[ 0.379010] pci 0001:00:00.0: calling pci_fixup_ide_bases+0x0/0x3c
[ 0.379069] pci 0001:00:00.0: supports D1
[ 0.379079] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[ 0.379092] pci 0001:00:00.0: PME# disabled
[ 0.379339] pci_bus 0001:00: fixups for bus
[ 0.379356] PCI: bus0: Fast back to back transfers disabled
[ 0.379372] pci 0001:00:00.0: scanning [bus 01-01] behind bridge, pass 0
[ 0.379503] pci_bus 0001:01: scanning bus
[ 0.379675] pci 0001:01:00.0: [168c:0040] type 00 class 0x028000
[ 0.379899] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.380345] pci 0001:01:00.0: calling pci_fixup_ide_bases+0x0/0x3c
[ 0.380983] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.381023] pci 0001:01:00.0: PME# disabled
[ 0.381366] pci_bus 0001:01: fixups for bus
[ 0.381437] PCI: bus1: Fast back to back transfers disabled
[ 0.381451] pci_bus 0001:01: bus scan returning with max=01
[ 0.381467] pci 0001:00:00.0: scanning [bus 01-01] behind bridge, pass 1
[ 0.381483] pci_bus 0001:00: bus scan returning with max=01
[ 0.381542] pcieport 0000:00:00.0: fixup irq: got 133
[ 0.381551] pcieport 0000:00:00.0: assigning IRQ 133
[ 0.381628] pci 0000:01:00.0: fixup irq: got 133
[ 0.381637] pci 0000:01:00.0: assigning IRQ 133
[ 0.381766] pci 0001:00:00.0: fixup irq: got 166
[ 0.381776] pci 0001:00:00.0: assigning IRQ 166
[ 0.381855] pci 0001:01:00.0: fixup irq: got 166
[ 0.381865] pci 0001:01:00.0: assigning IRQ 166
[ 0.381920] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[ 0.381942] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[ 0.382065] pci 0001:00:00.0: PCI bridge to [bus 01]
[ 0.382085] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
[ 0.382420] aer 0001:00:00.0:pcie002: service driver aer loaded
[ 0.385112] L2 @ QSB rate. Forcing new rate.
[ 0.385306] L2 @ 384000 KHz
[ 0.385480] CPU0 @ 800000 KHz
[ 0.385492] CPU1 @ QSB rate. Forcing new rate.
[ 0.385619] CPU1 @ 384000 KHz
[ 0.388294] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[ 0.389820] gsbi 1a200000.gsbi: GSBI port protocol: 3 crci: 0
[ 0.391319] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.392196] msm_serial 16340000.serial: msm_serial: detected port #0
[ 0.392303] msm_serial 16340000.serial: uartclk = 7372800
[ 0.392380] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 167, base_baud = 460800) is a MSM
[ 0.392417] msm_serial: console setup on port #0
[ 1.101648] console [ttyMSM0] enabled
[ 1.106364] msm_serial: driver initialized
[ 1.117864] loop: module loaded
[ 1.119399] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[ 1.121388] m25p80 spi32766.0: mx25u25635f (32768 Kbytes)
[ 1.127347] 25 ofpart partitions found on MTD device spi32766.0
[ 1.132612] Creating 25 MTD partitions on "spi32766.0":
[ 1.138225] 0x000000000000-0x000000020000 : "SBL1"
[ 1.144723] 0x000000020000-0x000000040000 : "MIBIB"
[ 1.149359] 0x000000040000-0x000000060000 : "SBL2"
[ 1.154061] 0x000000060000-0x000000090000 : "SBL3"
[ 1.159019] 0x000000090000-0x0000000a0000 : "DDRCONFIG"
[ 1.163688] 0x0000000a0000-0x0000000b0000 : "SSD"
[ 1.169147] 0x0000000b0000-0x0000000e0000 : "TZ"
[ 1.173692] 0x0000000e0000-0x000000100000 : "RPM"
[ 1.178611] 0x000000100000-0x000000170000 : "fs-uboot"
[ 1.183040] 0x000000170000-0x0000001b0000 : "uboot-env"
[ 1.188001] 0x0000001b0000-0x0000001f0000 : "radio"
[ 1.193178] 0x0000001f0000-0x0000003f0000 : "os-image"
[ 1.197992] 0x0000003f0000-0x000001ef0000 : "rootfs"
[ 1.203237] mtd: device 12 (rootfs) set to be root filesystem
[ 1.207550] 1 squashfs-split partitions found on MTD device rootfs
[ 1.213036] 0x000000720000-0x000001ef0000 : "rootfs_data"
[ 1.220117] 0x000001ef0000-0x000001ef0200 : "default-mac"
[ 1.225759] 0x000001ef0200-0x000001ef0400 : "pin"
[ 1.230953] 0x000001ef0400-0x000001f00000 : "product-info"
[ 1.235832] 0x000001f00000-0x000001f10000 : "partition-table"
[ 1.241070] 0x000001f10000-0x000001f20000 : "soft-version"
[ 1.246785] 0x000001f20000-0x000001f30000 : "support-list"
[ 1.252229] 0x000001f30000-0x000001f40000 : "profile"
[ 1.257610] 0x000001f40000-0x000001f50000 : "default-config"
[ 1.262853] 0x000001f50000-0x000001f90000 : "user-config"
[ 1.268837] 0x000001f90000-0x000001fd0000 : "qos-db"
[ 1.273768] 0x000001fd0000-0x000001fe0000 : "usb-config"
[ 1.279163] 0x000001fe0000-0x000002000000 : "log"
[ 1.284950] libphy: GPIO Bitbanged MDIO: probed
[ 1.313593] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0
[ 2.229691] libphy: Fixed MDIO Bus: probed
[ 2.229724] libphy: mdio_driver_register: qca8k
[ 2.234739] stmmac - user ID: 0x10, Synopsys ID: 0x37
[ 2.237110] Ring mode enabled
[ 2.242393] DMA HW capability register supported
[ 2.245268] Enhanced/Alternate descriptors
[ 2.250909] Enabled extended descriptors
[ 2.253868] RX Checksum Offload Engine supported
[ 2.258036] COE Type 2
[ 2.262783] TX Checksum insertion supported
[ 2.264979] Wake-Up On Lan supported
[ 2.269564] Enable RX Mitigation via HW Watchdog Timer
[ 2.274957] stmmac - user ID: 0x10, Synopsys ID: 0x37
[ 2.278088] Ring mode enabled
[ 2.283385] DMA HW capability register supported
[ 2.286247] Enhanced/Alternate descriptors
[ 2.291889] Enabled extended descriptors
[ 2.294846] RX Checksum Offload Engine supported
[ 2.299085] COE Type 2
[ 2.303698] TX Checksum insertion supported
[ 2.305958] Wake-Up On Lan supported
[ 2.310549] Enable RX Mitigation via HW Watchdog Timer
[ 2.314809] i2c /dev entries driver
[ 2.320000] Calibration not found.
[ 2.322545] qcom-tsens 900000.thermal-sensor: tsens calibration failed
[ 2.327080] Speed bin: 0
[ 2.332608] PVS bin: 1
[ 2.337010] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[ 2.337438] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[ 2.345199] sdhci: Secure Digital Host Controller Interface driver
[ 2.351943] sdhci: Copyright(c) Pierre Ossman
[ 2.358131] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.364315] NET: Registered protocol family 10
[ 2.369828] NET: Registered protocol family 17
[ 2.372837] 8021q: 802.1Q VLAN Support v1.8
[ 2.377021] Registering SWP/SWPB emulation handler
[ 2.393395] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342
[ 2.405014] s1a: Bringing 0uV into 1050000-1050000uV
[ 2.405353] s1b: Bringing 0uV into 1050000-1050000uV
[ 2.409420] s2a: Bringing 0uV into 800000-800000uV
[ 2.414274] s2b: Bringing 0uV into 800000-800000uV
[ 2.421672] of: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:0, -19
[ 2.423884] of: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:1, -19
[ 2.431926] hctosys: unable to open rtc device (rtc0)
[ 2.444233] random: fast init done
[ 2.446697] VFS: Mounted root (squashfs filesystem) readonly on device 31:12.
[ 2.446929] Freeing unused kernel memory: 240K (c0724000 - c0760000)
[ 2.453814] This architecture does not have kernel memory protection.
[ 2.707162] random: crng init done
[ 3.231184] init: Console is alive
[ 3.231461] init: - watchdog -
[ 5.606708] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.631388] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.633440] SCSI subsystem initialized
[ 5.639085] libata version 3.00 loaded.
[ 5.642247] ehci-platform: EHCI generic platform driver
[ 5.644920] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.646703] ohci-platform: OHCI generic platform driver
[ 5.779028] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 5.779102] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 5.783630] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x02010010
[ 5.791104] xhci-hcd xhci-hcd.0.auto: irq 169, io mem 0x11000000
[ 5.800675] hub 1-0:1.0: USB hub found
[ 5.805951] hub 1-0:1.0: 1 port detected
[ 5.809967] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 5.813547] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 5.819138] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 5.827189] hub 2-0:1.0: USB hub found
[ 5.834860] hub 2-0:1.0: 1 port detected
[ 5.838811] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 5.842376] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 5.847853] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x02010010
[ 5.855350] xhci-hcd xhci-hcd.1.auto: irq 170, io mem 0x10000000
[ 5.864823] hub 3-0:1.0: USB hub found
[ 5.870249] hub 3-0:1.0: 1 port detected
[ 5.874063] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 5.877781] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 5.883276] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 5.891474] hub 4-0:1.0: USB hub found
[ 5.899091] hub 4-0:1.0: 1 port detected
[ 5.905669] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.915271] init: - preinit -
[ 8.784757] dwmac1000: Master AXI performs any burst length
[ 8.784800] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 8.789313] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 8.798340] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 9.849572] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 9.850016] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 11.337086] jffs2: notice: (172) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 11.342074] mount_root: overlay filesystem has not been fully initialized yet
[ 19.443404] mount_root: switching to jffs2 overlay
[ 20.027552] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 20.125058] procd: - early -
[ 20.125155] procd: - watchdog -
[ 20.855207] procd: - watchdog -
[ 20.855660] procd: - ubus -
[ 21.013192] procd: - init -
[ 21.220998] kmodloader: loading kernel modules from /etc/modules.d/*
[ 21.224980] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 21.230352] Netfilter messages via NETLINK v0.30.
[ 21.232750] ip_set: protocol 6
[ 21.248739] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[ 21.248767] Backport generated by backports.git backports-20160324-13-g24da7d3c
[ 21.273162] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[ 21.273254] ath10k_pci 0000:01:00.0: enabling bus mastering
[ 21.273734] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 21.451476] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
[ 21.451523] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 82.190159] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[ 82.190206] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 82.202490] ath10k_pci 0000:01:00.0: firmware ver 10.4.1.00030-1 api 5 features no-p2p crc32 d2901e01
[ 82.262895] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 1:1 crc32 08fa09f2
[ 83.526583] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 512 raw 0 hwcrypto 1
[ 83.652156] ath: EEPROM regdomain: 0x0
[ 83.652168] ath: EEPROM indicates default country code should be used
[ 83.652177] ath: doing EEPROM country->regdmn map search
[ 83.652192] ath: country maps to regdmn code: 0x3a
[ 83.652203] ath: Country alpha2 being used: US
[ 83.652212] ath: Regpair used: 0x3a
[ 83.658954] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[ 83.659078] ath10k_pci 0001:01:00.0: enabling bus mastering
[ 83.659656] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 83.851129] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0001:01:00.0.bin failed with error -2
[ 83.851177] ath10k_pci 0001:01:00.0: Falling back to user helper
[ 146.529172] ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/cal-pci-0001:01:00.0.bin failed with error -2
[ 146.529225] ath10k_pci 0001:01:00.0: Falling back to user helper
[ 148.442922] firmware ath10k!cal-pci-0001:01:00.0.bin: firmware_loading_store: map pages failed
[ 148.443191] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[ 148.450573] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 148.467441] ath10k_pci 0001:01:00.0: firmware ver 10.4.1.00030-1 api 5 features no-p2p crc32 d2901e01
[ 150.756223] ath10k_pci 0001:01:00.0: board id is not exist in otp, ignore it
[ 150.756261] ath10k_pci 0001:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0040,subsystem-vendor=168c,subsystem-device=0002¦¦0¦MM¦M
[ 150.756261] |¦¦0¦OB¦¦?V¦i¦ from ath10k/QCA99X0/hw2.0/board-2.bin
[ 150.779488] ath10k_pci 0001:01:00.0: board_file api 1 bmi_id N/A crc32 7e56fd07
[ 154.239465] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal otp max-sta 512 raw 0 hwcrypto 1
[ 154.321987] ath: EEPROM regdomain: 0x0
[ 154.321998] ath: EEPROM indicates default country code should be used
[ 154.322006] ath: doing EEPROM country->regdmn map search
[ 154.322019] ath: country maps to regdmn code: 0x3a
[ 154.322029] ath: Country alpha2 being used: US
[ 154.322037] ath: Regpair used: 0x3a
[ 154.343783] u32 classifier
[ 154.343812] input device check on
[ 154.345381] Actions configured
[ 154.351096] Mirror/redirect action on
[ 154.376532] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
[ 154.382627] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 154.449334] xt_time: kernel timezone is -0000
[ 154.452587] PPP generic driver version 2.4.2
[ 154.453312] NET: Registered protocol family 24
[ 154.458218] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 160.176657] dwmac1000: Master AXI performs any burst length
[ 160.176699] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 160.181264] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 160.190248] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 160.203216] br-lan: port 1(eth1.1) entered blocking state
[ 160.203254] br-lan: port 1(eth1.1) entered disabled state
[ 160.208744] device eth1.1 entered promiscuous mode
[ 160.213779] device eth1 entered promiscuous mode
[ 160.222254] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 160.249642] dwmac1000: Master AXI performs any burst length
[ 160.249708] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 160.254249] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 160.263416] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 160.274620] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 160.723730] ath: EEPROM regdomain: 0x8282
[ 160.723738] ath: EEPROM indicates we should expect a country code
[ 160.723744] ath: doing EEPROM country->regdmn map search
[ 160.723749] ath: country maps to regdmn code: 0x3
[ 160.723753] ath: Country alpha2 being used: RO
[ 160.723756] ath: Regpair used: 0x3
[ 160.723761] ath: regdomain 0x8282 dynamically updated by user
[ 160.723784] ath: EEPROM regdomain: 0x8282
[ 160.723787] ath: EEPROM indicates we should expect a country code
[ 160.723791] ath: doing EEPROM country->regdmn map search
[ 160.723795] ath: country maps to regdmn code: 0x3
[ 160.723798] ath: Country alpha2 being used: RO
[ 160.723801] ath: Regpair used: 0x3
[ 160.723804] ath: regdomain 0x8282 dynamically updated by user
[ 161.211214] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 161.215063] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 161.219807] br-lan: port 1(eth1.1) entered blocking state
[ 161.225167] br-lan: port 1(eth1.1) entered forwarding state
[ 161.231029] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 161.289604] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 161.289674] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 161.298014] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 163.765320] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 163.768030] br-lan: port 2(wlan0) entered blocking state
[ 163.770168] br-lan: port 2(wlan0) entered disabled state
[ 163.776025] device wlan0 entered promiscuous mode
[ 163.781083] br-lan: port 2(wlan0) entered blocking state
[ 163.785504] br-lan: port 2(wlan0) entered forwarding state
[ 163.794081] br-lan: port 2(wlan0) entered disabled state
[ 228.479624] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 228.479750] br-lan: port 2(wlan0) entered blocking state
[ 228.485043] br-lan: port 2(wlan0) entered forwarding state
More information can be found at the following URL:
https://bugs.lede-project.org/index.php?do=details&task_id=957
More information about the lede-bugs
mailing list