[FS#78] Netgear R7800 - problem USB ports
LEDE Bugs
lede-bugs at lists.infradead.org
Sun Aug 7 02:03:26 PDT 2016
The following task has a new comment added:
FS#78 - Netgear R7800 - problem USB ports
User who did this - Maxim (lobyte)
----------
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.4.14 (openwrt at gb-10) (gcc version 5.3.0 (OpenWrt GCC 5.3.0 49876) ) #1 SMP PREEMPT Sun Jul 31 10:58:18 UTC 2016
[ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] Machine model: Netgear Nighthawk X4S R7800
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 122880
[ 0.000000] free_area_init_node: node 0, pgdat c079dd80, node_mem_map ddc39000
[ 0.000000] Normal zone: 960 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 122880 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 11 pages/cpu @ddc0f000 s14784 r8192 d22080 u45056
[ 0.000000] pcpu-alloc: s14784 r8192 d22080 u45056 alloc=11*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 121920
[ 0.000000] Kernel command line: rootfstype=squashfs noinitrd
[ 0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 480808K/491520K available (3892K kernel code, 244K rwdata, 1596K rodata, 204K init, 292K bss, 10712K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xde800000 - 0xff800000 ( 528 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xde000000 ( 480 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0208000 - 0xc07643fc (5489 kB)
[ 0.000000] .init : 0xc0765000 - 0xc0798000 ( 204 kB)
[ 0.000000] .data : 0xc0798000 - 0xc07d527c ( 245 kB)
[ 0.000000] .bss : 0xc07d8000 - 0xc0821384 ( 293 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[ 0.000007] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[ 0.000021] Switching to timer-based delay loop, resolution 160ns
[ 0.000199] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[ 0.000224] pid_max: default: 32768 minimum: 301
[ 0.000360] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000376] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000979] CPU: Testing write buffer coherency: ok
[ 0.001287] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.001391] Setting up static identity map for 0x42208280 - 0x422082d8
[ 0.094347] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.094502] Brought up 2 CPUs
[ 0.094528] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[ 0.094539] CPU: All CPU(s) started in SVC mode.
[ 0.104353] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[ 0.104793] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.104941] pinctrl core: initialized pinctrl subsystem
[ 0.106499] NET: Registered protocol family 16
[ 0.106793] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.134774] cpuidle: using governor ladder
[ 0.165788] cpuidle: using governor menu
[ 0.182642] gpiochip_add: registered GPIOs 0 to 68 on device: 800000.pinmux
[ 0.182669] GPIO chip 800000.pinmux: created GPIO range 0->68 ==> 800000.pinmux PIN 0->68
[ 0.184408] qcom_rpm 108000.rpm: RPM firmware 3.0.16777364
[ 0.239416] qcom_rpm_reg 108000.rpm:regulators: invalid frequency 1400000
[ 0.239436] qcom_rpm_reg 108000.rpm:regulators: driver callback failed to parse DT for regulator s2a
[ 0.239748] qcom_rpm_reg 108000.rpm:regulators: invalid frequency 1400000
[ 0.239764] qcom_rpm_reg 108000.rpm:regulators: driver callback failed to parse DT for regulator s2b
[ 0.240468] pps_core: LinuxPPS API ver. 1 registered
[ 0.240483] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[ 0.240528] PTP clock support registered
[ 0.241791] clocksource: Switched to clocksource dg_timer
[ 0.243754] NET: Registered protocol family 2
[ 0.244644] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.244693] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.244751] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.244809] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.244837] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.245069] NET: Registered protocol family 1
[ 0.245148] PCI: CLS 0 bytes, default 64
[ 0.246943] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.256252] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.256281] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.258723] io scheduler noop registered
[ 0.258752] io scheduler deadline registered (default)
[ 0.260415] qcom-pcie 1b500000.pci: GPIO lookup for consumer perst
[ 0.260434] qcom-pcie 1b500000.pci: using device tree for GPIO lookup
[ 0.260454] of_get_named_gpiod_flags: can't parse 'perst-gpios' property of node '/soc/pci at 1b500000[0]'
[ 0.260481] of_get_named_gpiod_flags: parsed 'perst-gpio' property of node '/soc/pci at 1b500000[0]' - status (0)
[ 0.260570] 1b500000.pci supply vdda not found, using dummy regulator
[ 0.260680] 1b500000.pci supply vdda_phy not found, using dummy regulator
[ 0.260790] 1b500000.pci supply vdda_refclk not found, using dummy regulator
[ 0.261245] PCI host bridge /soc/pci at 1b500000 ranges:
[ 0.261289] IO 0x0fe00000..0x0fefffff -> 0x0fe00000
[ 0.261317] MEM 0x08000000..0x0fdfffff -> 0x08000000
[ 0.290758] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[ 0.290786] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.290808] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff])
[ 0.290826] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[ 0.290843] pci_bus 0000:00: scanning bus
[ 0.290893] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400
[ 0.291031] pci 0000:00:00.0: calling pci_fixup_ide_bases+0x0/0x40
[ 0.291107] pci 0000:00:00.0: supports D1
[ 0.291123] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.291146] pci 0000:00:00.0: PME# disabled
[ 0.291562] pci_bus 0000:00: fixups for bus
[ 0.291592] PCI: bus0: Fast back to back transfers disabled
[ 0.291614] pci 0000:00:00.0: scanning [bus 01-01] behind bridge, pass 0
[ 0.291828] pci_bus 0000:01: scanning bus
[ 0.292084] pci 0000:01:00.0: [168c:0046] type 00 class 0x028000
[ 0.292487] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.292902] pci 0000:01:00.0: calling pci_fixup_ide_bases+0x0/0x40
[ 0.293337] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.293380] pci 0000:01:00.0: PME# disabled
[ 0.293854] pci_bus 0000:01: fixups for bus
[ 0.293922] PCI: bus1: Fast back to back transfers disabled
[ 0.293937] pci_bus 0000:01: bus scan returning with max=01
[ 0.293958] pci 0000:00:00.0: scanning [bus 01-01] behind bridge, pass 1
[ 0.293980] pci_bus 0000:00: bus scan returning with max=01
[ 0.294065] pci 0000:00:00.0: fixup irq: got 136
[ 0.294080] pci 0000:00:00.0: assigning IRQ 136
[ 0.294150] pci 0000:01:00.0: fixup irq: got 136
[ 0.294164] pci 0000:01:00.0: assigning IRQ 136
[ 0.294236] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[ 0.294262] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[ 0.294379] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.294404] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
[ 0.294816] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt
[ 0.294836] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[ 0.294855] pcie_pme 0000:00:00.0:pcie01: service driver pcie_pme loaded
[ 0.295086] aer 0000:00:00.0:pcie02: service driver aer loaded
[ 0.295418] qcom-pcie 1b700000.pci: GPIO lookup for consumer perst
[ 0.295434] qcom-pcie 1b700000.pci: using device tree for GPIO lookup
[ 0.295450] of_get_named_gpiod_flags: can't parse 'perst-gpios' property of node '/soc/pci at 1b700000[0]'
[ 0.295475] of_get_named_gpiod_flags: parsed 'perst-gpio' property of node '/soc/pci at 1b700000[0]' - status (0)
[ 0.295560] 1b700000.pci supply vdda not found, using dummy regulator
[ 0.295662] 1b700000.pci supply vdda_phy not found, using dummy regulator
[ 0.295772] 1b700000.pci supply vdda_refclk not found, using dummy regulator
[ 0.296187] PCI host bridge /soc/pci at 1b700000 ranges:
[ 0.296227] IO 0x31e00000..0x31efffff -> 0x31e00000
[ 0.296251] MEM 0x2e000000..0x31dfffff -> 0x2e000000
[ 0.324453] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[ 0.324473] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 0.324489] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[ 0.324505] pci_bus 0001:00: scanning bus
[ 0.324549] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400
[ 0.324654] pci 0001:00:00.0: calling pci_fixup_ide_bases+0x0/0x40
[ 0.324715] pci 0001:00:00.0: supports D1
[ 0.324729] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
[ 0.324747] pci 0001:00:00.0: PME# disabled
[ 0.325138] pci_bus 0001:00: fixups for bus
[ 0.325163] PCI: bus0: Fast back to back transfers disabled
[ 0.325181] pci 0001:00:00.0: scanning [bus 01-01] behind bridge, pass 0
[ 0.325383] pci_bus 0001:01: scanning bus
[ 0.325543] pci 0001:01:00.0: [168c:0046] type 00 class 0x028000
[ 0.325893] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.326302] pci 0001:01:00.0: calling pci_fixup_ide_bases+0x0/0x40
[ 0.326732] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.326774] pci 0001:01:00.0: PME# disabled
[ 0.327238] pci_bus 0001:01: fixups for bus
[ 0.327307] PCI: bus1: Fast back to back transfers disabled
[ 0.327321] pci_bus 0001:01: bus scan returning with max=01
[ 0.327343] pci 0001:00:00.0: scanning [bus 01-01] behind bridge, pass 1
[ 0.327364] pci_bus 0001:00: bus scan returning with max=01
[ 0.327418] pcieport 0000:00:00.0: fixup irq: got 136
[ 0.327432] pcieport 0000:00:00.0: assigning IRQ 136
[ 0.327498] pci 0000:01:00.0: fixup irq: got 136
[ 0.327512] pci 0000:01:00.0: assigning IRQ 136
[ 0.327596] pci 0001:00:00.0: fixup irq: got 169
[ 0.327610] pci 0001:00:00.0: assigning IRQ 169
[ 0.327678] pci 0001:01:00.0: fixup irq: got 169
[ 0.327692] pci 0001:01:00.0: assigning IRQ 169
[ 0.327752] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[ 0.327776] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[ 0.327889] pci 0001:00:00.0: PCI bridge to [bus 01]
[ 0.327910] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
[ 0.328280] pcieport 0001:00:00.0: Signaling PME through PCIe PME interrupt
[ 0.328298] pci 0001:01:00.0: Signaling PME through PCIe PME interrupt
[ 0.328317] pcie_pme 0001:00:00.0:pcie01: service driver pcie_pme loaded
[ 0.328521] aer 0001:00:00.0:pcie02: service driver aer loaded
[ 0.334319] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[ 0.335953] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.341349] msm_serial 16340000.serial: msm_serial: detected port #0
[ 0.341462] msm_serial 16340000.serial: uartclk = 1843200
[ 0.341539] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 170, base_baud = 115200) is a MSM
[ 0.341593] msm_serial: console setup on port #0
[ 1.044850] console [ttyMSM0] enabled
[ 1.049657] msm_serial: driver initialized
[ 1.056750] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1
[ 1.056861] nand: AMD/Spansion S34MS01G2
[ 1.063458] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.067295] Scanning device for bad blocks
[ 1.560799] random: nonblocking pool is initialized
[ 1.922250] 10 ofpart partitions found on MTD device qcom-nandc
[ 1.922281] Creating 10 MTD partitions on "qcom-nandc":
[ 1.926980] 0x000000000000-0x000000c80000 : "qcadata"
[ 1.933955] 0x000000c80000-0x000001180000 : "APPSBL"
[ 1.949483] 0x000001180000-0x000001200000 : "APPSBLENV"
[ 1.961581] 0x000001200000-0x000001340000 : "art"
[ 1.973465] 0x000001340000-0x000001480000 : "artbak"
[ 1.985230] 0x000001480000-0x000001680000 : "kernel"
[ 1.986735] 0x000001680000-0x000003480000 : "ubi"
[ 1.990817] 0x000003480000-0x000007900000 : "netgear"
[ 1.995561] 0x000007900000-0x000008000000 : "reserve"
[ 2.010652] 0x000001480000-0x000003480000 : "firmware"
[ 2.023976] no rootfs found after FIT image in "firmware"
[ 2.025200] libphy: Fixed MDIO Bus: probed
[ 2.028682] of_get_named_gpiod_flags: parsed 'gpios' property of node '/soc/mdio[0]' - status (0)
[ 2.028712] of_get_named_gpiod_flags: parsed 'gpios' property of node '/soc/mdio[1]' - status (0)
[ 2.028735] of_get_named_gpiod_flags: can't parse 'gpios' property of node '/soc/mdio[2]'
[ 2.028934] libphy: GPIO Bitbanged MDIO: probed
[ 2.058600] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0
[ 2.330076] of_get_named_gpiod_flags: can't parse 'link-gpios' property of node '/soc/ethernet at 37200000/fixed-link[0]'
[ 2.330856] stmmac - user ID: 0x10, Synopsys ID: 0x37
[ 2.330887] Ring mode enabled
[ 2.334955] DMA HW capability register supported
[ 2.337836] Enhanced/Alternate descriptors
[ 2.342610] Enabled extended descriptors
[ 2.346603] RX Checksum Offload Engine supported (type 2)
[ 2.350770] TX Checksum insertion supported
[ 2.356224] Wake-Up On Lan supported
[ 2.360651] Enable RX Mitigation via HW Watchdog Timer
[ 2.365272] of_get_named_gpiod_flags: can't parse 'link-gpios' property of node '/soc/ethernet at 37400000/fixed-link[0]'
[ 2.365960] stmmac - user ID: 0x10, Synopsys ID: 0x37
[ 2.369173] Ring mode enabled
[ 2.374492] DMA HW capability register supported
[ 2.377333] Enhanced/Alternate descriptors
[ 2.382189] Enabled extended descriptors
[ 2.386098] RX Checksum Offload Engine supported (type 2)
[ 2.390267] TX Checksum insertion supported
[ 2.395709] Wake-Up On Lan supported
[ 2.400145] Enable RX Mitigation via HW Watchdog Timer
[ 2.404601] i2c /dev entries driver
[ 2.410160] Speed bin: 0
[ 2.412223] PVS bin: 3
[ 2.417703] L2 @ QSB rate. Forcing new rate.
[ 2.417862] L2 @ 384000 KHz
[ 2.421656] CPU0 @ 800000 KHz
[ 2.424126] CPU1 @ QSB rate. Forcing new rate.
[ 2.427243] CPU1 @ 384000 KHz
[ 2.433277] NET: Registered protocol family 10
[ 2.436136] NET: Registered protocol family 17
[ 2.438963] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.443485] Bridge firewalling registered
[ 2.456510] 8021q: 802.1Q VLAN Support v1.8
[ 2.460066] Registering SWP/SWPB emulation handler
[ 2.467738] UBI: auto-attach mtd6
[ 2.468833] ubi0: attaching mtd6
[ 2.875090] ubi0: scanning is finished
[ 2.896284] ubi0: attached mtd6 (name "ubi", size 30 MiB)
[ 2.896322] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 2.900669] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 2.907529] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 2.914391] ubi0: good PEBs: 240, bad PEBs: 0, corrupted PEBs: 0
[ 2.921068] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 2.927419] ubi0: max/mean erase counter: 5/3, WL threshold: 4096, image sequence number: 873690004
[ 2.934448] ubi0: available PEBs: 0, total reserved PEBs: 240, PEBs reserved for bad PEB handling: 20
[ 2.943548] ubi0: background thread "ubi_bgt0d" started, PID 49
[ 2.953932] block ubiblock0_0: created from ubi0:0(rootfs)
[ 2.958394] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 2.964058] hctosys: unable to open rtc device (rtc0)
[ 2.990645] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 2.990963] Freeing unused kernel memory: 204K (c0765000 - c0798000)
[ 3.675128] init: Console is alive
[ 3.675391] init: - watchdog -
[ 4.544050] usbcore: registered new interface driver usbfs
[ 4.544269] usbcore: registered new interface driver hub
[ 4.548693] usbcore: registered new device driver usb
[ 4.556284] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-keys/wifi[0]' - status (0)
[ 4.556339] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-keys/reset[0]' - status (0)
[ 4.556390] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-keys/wps[0]' - status (0)
[ 4.565357] SCSI subsystem initialized
[ 4.583851] libata version 3.00 loaded.
[ 4.590337] ahci 29000000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x0 impl platform mode
[ 4.590407] ahci 29000000.sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
[ 4.610200] scsi host0: ahci
[ 4.611060] ata1: DUMMY
[ 4.619144] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.620595] ehci-platform: EHCI generic platform driver
[ 4.636587] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.638125] ohci-platform: OHCI generic platform driver
[ 4.643948] qcom-dwc3 soc:usb30 at 0: failed to get optional iface clock
[ 4.646819] qcom-dwc3 soc:usb30 at 0: failed to get optional sleep clock
[ 4.655304] qcom-dwc3 soc:usb30 at 1: failed to get optional iface clock
[ 4.659836] qcom-dwc3 soc:usb30 at 1: failed to get optional sleep clock
[ 5.177252] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 5.177361] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 5.181979] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x00010010
[ 5.189468] xhci-hcd xhci-hcd.0.auto: irq 171, io mem 0x11000000
[ 5.199971] hub 1-0:1.0: USB hub found
[ 5.204340] hub 1-0:1.0: 1 port detected
[ 5.210004] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 5.211801] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 5.217512] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 5.226522] hub 2-0:1.0: USB hub found
[ 5.233240] hub 2-0:1.0: 1 port detected
[ 5.239335] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 5.240639] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 5.246380] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x00010010
[ 5.253688] xhci-hcd xhci-hcd.1.auto: irq 172, io mem 0x10000000
[ 5.263995] hub 3-0:1.0: USB hub found
[ 5.268445] hub 3-0:1.0: 1 port detected
[ 5.274131] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 5.276033] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 5.281533] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 5.290778] hub 4-0:1.0: USB hub found
[ 5.297401] hub 4-0:1.0: 1 port detected
[ 5.305845] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/usb1[0]' - status (0)
[ 5.306222] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/usb3[0]' - status (0)
[ 5.306556] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/status[0]' - status (0)
[ 5.306872] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/internet[0]' - status (0)
[ 5.307193] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/wan[0]' - status (0)
[ 5.307535] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/wps[0]' - status (0)
[ 5.307857] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/esata[0]' - status (0)
[ 5.308181] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/power[0]' - status (0)
[ 5.308505] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/rfkill[0]' - status (0)
[ 5.308848] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-leds/wifi[0]' - status (0)
[ 5.321360] init: - preinit -
[ 8.967532] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 93
[ 9.058612] UBIFS (ubi0:1): recovery needed
[ 9.330200] UBIFS (ubi0:1): recovery completed
[ 9.330379] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 9.333698] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 9.341497] UBIFS (ubi0:1): FS size: 23744512 bytes (22 MiB, 187 LEBs), journal size 1142784 bytes (1 MiB, 9 LEBs)
[ 9.351779] UBIFS (ubi0:1): reserved for root: 1121511 bytes (1095 KiB)
[ 9.361722] UBIFS (ubi0:1): media format: w4/r0 (latest is w4/r0), UUID 6CF62BF6-268B-4B44-A227-2077F9DFE466, small LPT model
[ 9.389919] mount_root: loading kmods from internal overlay
[ 9.544369] usbcore: registered new interface driver usb-storage
[ 9.575312] blk_update_request: I/O error, dev mtdblock0, sector 0
[ 9.576159] blk_update_request: I/O error, dev mtdblock0, sector 8
[ 9.581184] blk_update_request: I/O error, dev mtdblock0, sector 16
[ 9.587516] blk_update_request: I/O error, dev mtdblock0, sector 24
[ 9.593772] blk_update_request: I/O error, dev mtdblock0, sector 0
[ 9.598996] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[ 9.606423] blk_update_request: I/O error, dev mtdblock1, sector 0
[ 9.613453] blk_update_request: I/O error, dev mtdblock1, sector 8
[ 9.619576] blk_update_request: I/O error, dev mtdblock1, sector 16
[ 9.625854] blk_update_request: I/O error, dev mtdblock1, sector 24
[ 9.632040] blk_update_request: I/O error, dev mtdblock1, sector 0
[ 9.637269] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[ 9.888323] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 9.894118] block: extroot: not configured
[ 9.935512] mount_root: switching to jffs2 overlay
[ 9.960013] procd: - early -
[ 9.960213] procd: - watchdog -
[ 10.694319] procd: - ubus -
[ 10.753134] procd: - init -
[ 11.790369] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 11.798977] Loading modules backported from Linux version wt-2016-05-12-0-g7a54796
[ 11.799014] Backport generated by backports.git backports-20160216-0-ge3c56e4
[ 11.839159] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.846511] nf_conntrack version 0.5.0 (7515 buckets, 30060 max)
[ 11.966808] usbcore: registered new interface driver ums-alauda
[ 11.968103] usbcore: registered new interface driver ums-cypress
[ 11.972953] usbcore: registered new interface driver ums-datafab
[ 11.978976] usbcore: registered new interface driver ums-freecom
[ 11.985127] usbcore: registered new interface driver ums-isd200
[ 11.991061] usbcore: registered new interface driver ums-jumpshot
[ 11.996759] usbcore: registered new interface driver ums-karma
[ 12.003274] usbcore: registered new interface driver ums-sddr09
[ 12.008694] usbcore: registered new interface driver ums-sddr55
[ 12.014718] usbcore: registered new interface driver ums-usbat
[ 12.030968] xt_time: kernel timezone is -0000
[ 12.038734] PPP generic driver version 2.4.2
[ 12.039977] NET: Registered protocol family 24
[ 15.986164] blk_update_request: I/O error, dev mtdblock0, sector 0
[ 15.987064] blk_update_request: I/O error, dev mtdblock0, sector 8
[ 15.992083] blk_update_request: I/O error, dev mtdblock0, sector 16
[ 16.002321] blk_update_request: I/O error, dev mtdblock0, sector 24
[ 16.012706] blk_update_request: I/O error, dev mtdblock0, sector 0
[ 16.012766] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[ 16.022660] blk_update_request: I/O error, dev mtdblock1, sector 0
[ 16.032557] blk_update_request: I/O error, dev mtdblock1, sector 8
[ 16.042545] blk_update_request: I/O error, dev mtdblock1, sector 16
[ 16.052534] blk_update_request: I/O error, dev mtdblock1, sector 24
[ 16.062545] blk_update_request: I/O error, dev mtdblock1, sector 0
[ 16.062600] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[ 17.266575] device eth1 entered promiscuous mode
[ 17.271772] br-lan: port 1(eth1) entered forwarding state
[ 17.271850] br-lan: port 1(eth1) entered forwarding state
[ 19.263140] br-lan: port 1(eth1) entered forwarding state
[ 19.263356] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 19.302228] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
----------
One or more files have been attached.
More information can be found at the following URL:
https://bugs.lede-project.org/index.php?do=details&task_id=78#comment193
More information about the lede-bugs
mailing list