[PATCH] rpmsg: virtio: Fix broken rpmsg_probe()

[Michael S. Tsirkin]

On Wed, Jun 29, 2022 at 11:43:18AM -0600, Mathieu Poirier wrote:
> Hi Anup,
> 
> On Wed, Jun 08, 2022 at 10:43:34PM +0530, Anup Patel wrote:
> > The rpmsg_probe() is broken at the moment because virtqueue_add_inbuf()
> > fails due to both virtqueues (Rx and Tx) marked as broken by the
> > __vring_new_virtqueue() function. To solve this, virtio_device_ready()
> > (which unbreaks queues) should be called before virtqueue_add_inbuf().
> > 
> > Fixes: 8b4ec69d7e09 ("virtio: harden vring IRQ")
> > Signed-off-by: Anup Patel <apatel at ventanamicro.com>
> > ---
> >  drivers/rpmsg/virtio_rpmsg_bus.c | 6 +++---
> >  1 file changed, 3 insertions(+), 3 deletions(-)
> > 
> > diff --git a/drivers/rpmsg/virtio_rpmsg_bus.c b/drivers/rpmsg/virtio_rpmsg_bus.c
> > index 905ac7910c98..71a64d2c7644 100644
> > --- a/drivers/rpmsg/virtio_rpmsg_bus.c
> > +++ b/drivers/rpmsg/virtio_rpmsg_bus.c
> > @@ -929,6 +929,9 @@ static int rpmsg_probe(struct virtio_device *vdev)
> >  	/* and half is dedicated for TX */
> >  	vrp->sbufs = bufs_va + total_buf_space / 2;
> >  
> > +	/* From this point on, we can notify and get callbacks. */
> > +	virtio_device_ready(vdev);
> > +
> 
> Calling virtio_device_ready() here means that virtqueue_get_buf_ctx_split() can
> potentially be called (by way of rpmsg_recv_done()), which will race with
> virtqueue_add_inbuf().  If buffers in the virtqueue aren't available then
> rpmsg_recv_done() will fail, potentially breaking remote processors' state
> machines that don't expect their initial name service to fail when the "device"
> has been marked as ready.

When you say available I am guessing you really need used.

With a non broken device you won't get a callback
until some buffers have been used.

Or, if no used buffers are present then you will get another
callback down the road.


> 
> What does make me curious though is that nobody on the remoteproc mailing list
> has complained about commit 8b4ec69d7e09 breaking their environment... By now,
> i.e rc4, that should have happened.  Anyone from TI, ST and Xilinx care to test this on
> their rig?
> 
> Thanks,
> Mathieu
> 
> >  	/* set up the receive buffers */
> >  	for (i = 0; i < vrp->num_bufs / 2; i++) {
> >  		struct scatterlist sg;
> > @@ -983,9 +986,6 @@ static int rpmsg_probe(struct virtio_device *vdev)
> >  	 */
> >  	notify = virtqueue_kick_prepare(vrp->rvq);
> >  
> > -	/* From this point on, we can notify and get callbacks. */
> > -	virtio_device_ready(vdev);
> > -
> >  	/* tell the remote processor it can start sending messages */
> >  	/*
> >  	 * this might be concurrent with callbacks, but we are only
> > -- 
> > 2.34.1
> > 
>