mgag200 fails kdump kernel booting
dyoung at redhat.com
Mon Jul 1 20:17:15 PDT 2019
On 07/02/19 at 09:41am, Baoquan He wrote:
> On 07/02/19 at 06:51am, David Airlie wrote:
> > On Wed, Jun 26, 2019 at 6:29 PM Baoquan He <bhe at redhat.com> wrote:
> > >
> > > On 06/26/19 at 04:15pm, Baoquan He wrote:
> > > > Hi Dave,
> > > >
> > > > We met an kdump kernel boot failure on a lenovo system. Kdump kernel
> > > > failed to boot, but just reset to firmware to reboot system. And nothing
> > > > is printed out.
> > > >
> > > > The machine is a big server, with 6T memory and many cpu, its graphic
> > > > driver module is mgag200.
> > > >
> > > > When added 'earlyprintk=ttyS0' into kernel command line, it printed
> > > > out only one line to console during kdump kernel booting:
> > > > KASLR disabled: 'nokaslr' on cmdline.
> > > >
> > > > Then reset to firmware to reboot system.
> > > >
> > > > By further code debugging, the failure happened in
> > > > arch/x86/boot/compressed/misc.c, during kernel decompressing stage. It's
> > > > triggered by the vga printing. As you can see, in __putstr() of
> > > > arch/x86/boot/compressed/misc.c, the code checks if earlyprintk= is
> > > > specified, and print out to the target. And no matter if earlyprintk= is
> > > > added or not, it will print to VGA. And printing to VGA caused it to
> > > > reset to firmware. That's why we see nothing when didn't specify
> > > > earlyprintk=, but see only one line of printing about the 'KASLR
> > > > disabled'.
> > >
> > > Here I mean:
> > > That's why we see nothing when didn't specify earlyprintk=, but see only
> > > one line of printing about the 'KASLR disabled' message when
> > > earlyprintk=ttyS0 added.
> > Just to clarify, the original kernel is booted with mgag200 turned
> > off, then kexec works, but if the original kernel loads mgag200, the
> > kexec kernels resets hard when the VGA is used to write stuff out.
> Thanks for looking into this, Dave.
> Yeah, in fact the issue was found in kdump kernel. I haven't checked the
> kexec jumping. Kexec jumping will call device_shutdown() to attempt to
> shutdown all devices before jumping to the 2nd kernel. But kdump jumping
> > This *might* be fixable in the controlled kexec case, but having an
> > mgag200 shutdown path that tries to put the gpu back into a state
> > where VGA doesn't die, but for the uncontrolled kexec it'll still be a
> > problem, since once the gpu is up and running and VGA is disabled, it
> > doesn't expect to see anymore VGA transactions.
> Yes, I see. It should have been shutdown by device_shutdown() in kexec
> case. The uncontrolled case, I guess you mean the kdump case. In
> kdump case, we don't call device_shutdown() before jumping because the
> 1st kernel has been in crashed state, we just want to switch to kdump
> kernel asap. So wondering how other GPU/VGA device/driver bebahve,
> currently haven't got report about them. Probably mgag200 is very new,
> or we may not meet them. This issue was met on a new bought server.
I assumed the vga writing only take effect when earlyprintk is provided.
eg. earlyprintk=ttyS0, then x86 early decompress code will write to both
vga and ttyS0. So if one does not use earlyprintk, he/she still get
nothing. But if one provides earlyprintk, then he/she should provide a
correct param he want, instead of blindly assume kernel will write to
vga even if he use ttyS0.
More information about the kexec