[PATCH v3 1/3] kexec: Move vmcoreinfo out of the kernel's .bss section

Michael Holzheu holzheu at linux.vnet.ibm.com
Thu Mar 23 10:46:31 PDT 2017


Am Thu, 23 Mar 2017 17:23:53 +0800
schrieb Xunlei Pang <xpang at redhat.com>:

> On 03/23/2017 at 04:48 AM, Michael Holzheu wrote:
> > Am Wed, 22 Mar 2017 12:30:04 +0800
> > schrieb Dave Young <dyoung at redhat.com>:
> >
> >> On 03/21/17 at 10:18pm, Eric W. Biederman wrote:
> >>> Dave Young <dyoung at redhat.com> writes:
> >>>
> > [snip]
> >
> >>>> I think makedumpfile is using it, but I also vote to remove the
> >>>> CRASHTIME. It is better not to do this while crashing and a makedumpfile
> >>>> userspace patch is needed to drop the use of it.
> >>>>
> >>>>> As we are looking at reliability concerns removing CRASHTIME should make
> >>>>> everything in vmcoreinfo a boot time constant.  Which should simplify
> >>>>> everything considerably.
> >>>> It is a nice improvement..
> >>> We also need to take a close look at what s390 is doing with vmcoreinfo.
> >>> As apparently it is reading it in a different kind of crashdump process.
> >> Yes, need careful review from s390 and maybe ppc64 especially about
> >> patch 2/3, better to have comments from IBM about s390 dump tool and ppc
> >> fadump. Added more cc.
> > On s390 we have at least an issue with patch 1/3. For stand-alone dump
> > and also because we create the ELF header for kdump in the new
> > kernel we save the pointer to the vmcoreinfo note in the old kernel on a
> > defined memory address in our absolute zero lowcore.
> >
> > This is done in arch/s390/kernel/setup.c:
> >
> > static void __init setup_vmcoreinfo(void)
> > {
> >         mem_assign_absolute(S390_lowcore.vmcore_info, paddr_vmcoreinfo_note());
> > }
> >
> > Since with patch 1/3 paddr_vmcoreinfo_note() returns NULL at this point in
> > time we have a problem here.
> >
> > To solve this - I think - we could move the initialization to
> > arch/s390/kernel/machine_kexec.c:
> >
> > void arch_crash_save_vmcoreinfo(void)
> > {
> >         VMCOREINFO_SYMBOL(lowcore_ptr);
> >         VMCOREINFO_SYMBOL(high_memory);
> >         VMCOREINFO_LENGTH(lowcore_ptr, NR_CPUS);
> >         mem_assign_absolute(S390_lowcore.vmcore_info, paddr_vmcoreinfo_note());
> > }
> >
> > Probably related to this is my observation that patch 3/3 leads to
> > an empty VMCOREINFO note for kdump on s390. The note is there ...
> >
> > # readelf -n /var/crash/127.0.0.1-2017-03-22-21:14:39/vmcore | grep VMCORE
> >   VMCOREINFO           0x0000068e       Unknown note type: (0x00000000)
> >
> > But it contains only zeros.
> 
> Yes, this is a good catch, I will do more tests.

Hello Xunlei,

After spending some time on this, I now understood the problem:

In patch 3/3 you copy vmcoreinfo into the control page before
machine_kexec_prepare() is called. For s390 we give back all the
crashkernel memory to the hypervisor before the new crashkernel
is loaded:

/*
 * Give back memory to hypervisor before new kdump is loaded
 */
static int machine_kexec_prepare_kdump(void)
{
#ifdef CONFIG_CRASH_DUMP
        if (MACHINE_IS_VM)
                diag10_range(PFN_DOWN(crashk_res.start),
                             PFN_DOWN(crashk_res.end - crashk_res.start + 1));
        return 0;
#else
        return -EINVAL;
#endif
}

So after machine_kexec_prepare_kdump() the contents of your control page
is gone and therefore the vmcorinfo ELF note contains only zeros.

If you call kimage_crash_copy_vmcoreinfo() after
machine_kexec_prepare_kdump() the problem should be solved for s390.

Regards
Michael




More information about the kexec mailing list